SITE PROGRAM EVALUATION OF THE SONOTECH PULSE COMBUSTION BURNER TECHNOLOGY - TECHNICAL RESULTS

EPA Science Inventory

A series of demonstration tests was performed at the Environmental Protection Agency's (EPA's) Incineration Research Facility (IRF) under the Superfund Innovative Technology Evaluation (SITE) program. These tests, twelve in all, evaluated a pulse combustion burner technology dev...

[Hapten selection for patch tests in the diagnosis of allergic contact dermatitis: epidemiologic data].

PubMed

Romano, C; Carosso, A; Bosio, D; Chiesa, A; Gullino, A; Turrini, A

2003-01-01

Aim of the study was to verify the reliability in clinical practice of patch testing with "standard" series and additional series of haptens for the diagnosis of occupational and non-occupational allergic contact dermatitis, evaluating positive reactions and relating those reactions to professional categories. A total of 392 out of 937 patients (41.8%) showed at least one positive reaction to "standard" series testing; the hapten most frequently noted as the cause of positive reaction was nickel sulphate. Professional categories that showed positive reactions to "standard" series most frequently were clerks, hairdressers and hospital auxiliary workers. Among 897 patients tested with nonstandard allergens, only 124 (13.8%) elicited at least one positive reaction, ammonium persulphate being the most frequently positive hapten. A dominant percentage of positive results was seen in hairdressers and cleaning personnel. No positive reactions were observed in a large number of haptens, tested more than 200 times. Haptens of "standard series" elicited a higher number of positive reaction than the additional series, even though there was a high specificity of few additional series haptens in some professional categories. Data suggest some caution in systematically testing additional series, despite a higher accuracy and diagnostic efficacy in some job categories.

Boeing's CST-100 Structural Test Article Arrival - Boeing's Faci

NASA Image and Video Library

2016-12-08

Boeing’s Structural Test Article of its CST-100 Starliner spacecraft arrives at the company’s Huntington Beach, California, facilities for evaluations. Built to the specifications of an operational spacecraft, the STA is intended to be evaluated through a series of thorough testing conditions.

Patch test standard series recommended by the Brazilian Contact Dermatitis Study Group during the 2006-2011 period.

PubMed

Duarte, Ida Alzira Gomes; Tanaka, Greta Merie; Suzuki, Nathalie Mie; Lazzarini, Rosana; Lopes, Andressa Sato de Aquino; Volpini, Beatrice Mussio Fornazier; Castro, Paulo Carrara de

2013-01-01

A retrospective study was carried out between 2006-2011. Six hundred and eighteen patients with suspected allergic contact dermatitis underwent the standard patch test series recommended by the Brazilian Contact Dermatitis Research Group. The aim of our study was to evaluate the variation of positive patch-test results from standard series year by year. The most frequently positive allergens were: nickel sulfate, thimerosal and potassium bichromate. Decrease of positive patch-test results over the years was statistically significant for: lanolin (p=0.01), neomycin (p=0.01) and anthraquinone (p=0.04). A follow-up study should be useful in determining which allergens could be excluded from standard series, as they may represent low sensitization risk.

Manufacturing Process Developments for Regeneratively-Cooled Channel Wall Rocket Nozzles

NASA Technical Reports Server (NTRS)

Gradl, Paul; Brandsmeier, Will

2016-01-01

Regeneratively cooled channel wall nozzles incorporate a series of integral coolant channels to contain the coolant to maintain adequate wall temperatures and expand hot gas providing engine thrust and specific impulse. NASA has been evaluating manufacturing techniques targeting large scale channel wall nozzles to support affordability of current and future liquid rocket engine nozzles and thrust chamber assemblies. The development of these large scale manufacturing techniques focus on the liner formation, channel slotting with advanced abrasive water-jet milling techniques and closeout of the coolant channels to replace or augment other cost reduction techniques being evaluated for nozzles. NASA is developing a series of channel closeout techniques including large scale additive manufacturing laser deposition and explosively bonded closeouts. A series of subscale nozzles were completed evaluating these processes. Fabrication of mechanical test and metallography samples, in addition to subscale hardware has focused on Inconel 625, 300 series stainless, aluminum alloys as well as other candidate materials. Evaluations of these techniques are demonstrating potential for significant cost reductions for large scale nozzles and chambers. Hot fire testing is planned using these techniques in the future.

Self-test web-based pure-tone audiometry: validity evaluation and measurement error analysis.

PubMed

Masalski, Marcin; Kręcicki, Tomasz

2013-04-12

Potential methods of application of self-administered Web-based pure-tone audiometry conducted at home on a PC with a sound card and ordinary headphones depend on the value of measurement error in such tests. The aim of this research was to determine the measurement error of the hearing threshold determined in the way described above and to identify and analyze factors influencing its value. The evaluation of the hearing threshold was made in three series: (1) tests on a clinical audiometer, (2) self-tests done on a specially calibrated computer under the supervision of an audiologist, and (3) self-tests conducted at home. The research was carried out on the group of 51 participants selected from patients of an audiology outpatient clinic. From the group of 51 patients examined in the first two series, the third series was self-administered at home by 37 subjects (73%). The average difference between the value of the hearing threshold determined in series 1 and in series 2 was -1.54dB with standard deviation of 7.88dB and a Pearson correlation coefficient of .90. Between the first and third series, these values were -1.35dB±10.66dB and .84, respectively. In series 3, the standard deviation was most influenced by the error connected with the procedure of hearing threshold identification (6.64dB), calibration error (6.19dB), and additionally at the frequency of 250Hz by frequency nonlinearity error (7.28dB). The obtained results confirm the possibility of applying Web-based pure-tone audiometry in screening tests. In the future, modifications of the method leading to the decrease in measurement error can broaden the scope of Web-based pure-tone audiometry application.

Final Technical Report 1976-1977. Systemwide Evaluation. Publication Number: 76.69.

ERIC Educational Resources Information Center

Austin Independent School District, TX. Office of Research and Evaluation.

A series of reports describes the activities of the Office of Research and Evaluation and compiles data descriptive of the Austin (Texas) Independent School District. This report consists of four appendices, one for each of four test batteries: California Achievement Tests, Sequential Tests of Educational Progress, Boehm Tests of Basic Concepts,…

Evaluation of optical connectors for consideration in military avionics

NASA Astrophysics Data System (ADS)

Uhlhorn, Brian L.; Drexler, Gregory M.; Nelson, Ryan L.; Stevens, Rick C.

2006-08-01

This paper describes the method used to evaluate single-mode optical connectors under consideration for military avionics platforms. This testing is described in terms of the appropriate fiber optics test procedures (FOTPs) from the TIA/EIA-455 series.

A concise evidence-based physical examination for diagnosis of acromioclavicular joint pathology: a systematic review.

PubMed

Krill, Michael K; Rosas, Samuel; Kwon, KiHyun; Dakkak, Andrew; Nwachukwu, Benedict U; McCormick, Frank

2018-02-01

The clinical examination of the shoulder joint is an undervalued diagnostic tool for evaluating acromioclavicular (AC) joint pathology. Applying evidence-based clinical tests enables providers to make an accurate diagnosis and minimize costly imaging procedures and potential delays in care. The purpose of this study was to create a decision tree analysis enabling simple and accurate diagnosis of AC joint pathology. A systematic review of the Medline, Ovid and Cochrane Review databases was performed to identify level one and two diagnostic studies evaluating clinical tests for AC joint pathology. Individual test characteristics were combined in series and in parallel to improve sensitivities and specificities. A secondary analysis utilized subjective pre-test probabilities to create a clinical decision tree algorithm with post-test probabilities. The optimal special test combination to screen and confirm AC joint pathology combined Paxinos sign and O'Brien's Test, with a specificity of 95.8% when performed in series; whereas, Paxinos sign and Hawkins-Kennedy Test demonstrated a sensitivity of 93.7% when performed in parallel. Paxinos sign and O'Brien's Test demonstrated the greatest positive likelihood ratio (2.71); whereas, Paxinos sign and Hawkins-Kennedy Test reported the lowest negative likelihood ratio (0.35). No combination of special tests performed in series or in parallel creates more than a small impact on post-test probabilities to screen or confirm AC joint pathology. Paxinos sign and O'Brien's Test is the only special test combination that has a small and sometimes important impact when used both in series and in parallel. Physical examination testing is not beneficial for diagnosis of AC joint pathology when pretest probability is unequivocal. In these instances, it is of benefit to proceed with procedural tests to evaluate AC joint pathology. Ultrasound-guided corticosteroid injections are diagnostic and therapeutic. An ultrasound-guided AC joint corticosteroid injection may be an appropriate new standard for treatment and surgical decision-making. II - Systematic Review.

Evaluation of the base/subgrade soil under repeated loading : phase II, in-box and ALF cyclic plate load tests.

DOT National Transportation Integrated Search

2012-03-01

This research study aims at evaluating the performance of base and subgrade soil in flexible pavements under repeated loading test conditions. For this purpose, an indoor cyclic plate load testing equipment was developed and used to conduct a series ...

Image quality, meteorological optical range, and fog particulate number evaluation using the Sandia National Laboratories fog chamber

DOE PAGES

Birch, Gabriel C.; Woo, Bryana L.; Sanchez, Andres L.; ...

2017-08-24

The evaluation of optical system performance in fog conditions typically requires field testing. This can be challenging due to the unpredictable nature of fog generation and the temporal and spatial nonuniformity of the phenomenon itself. We describe the Sandia National Laboratories fog chamber, a new test facility that enables the repeatable generation of fog within a 55 m×3 m×3 m (L×W×H) environment, and demonstrate the fog chamber through a series of optical tests. These tests are performed to evaluate system image quality, determine meteorological optical range (MOR), and measure the number of particles in the atmosphere. Relationships between typical opticalmore » quality metrics, MOR values, and total number of fog particles are described using the data obtained from the fog chamber and repeated over a series of three tests.« less

Image quality, meteorological optical range, and fog particulate number evaluation using the Sandia National Laboratories fog chamber

DOE Office of Scientific and Technical Information (OSTI.GOV)

Birch, Gabriel C.; Woo, Bryana L.; Sanchez, Andres L.

The evaluation of optical system performance in fog conditions typically requires field testing. This can be challenging due to the unpredictable nature of fog generation and the temporal and spatial nonuniformity of the phenomenon itself. We describe the Sandia National Laboratories fog chamber, a new test facility that enables the repeatable generation of fog within a 55 m×3 m×3 m (L×W×H) environment, and demonstrate the fog chamber through a series of optical tests. These tests are performed to evaluate system image quality, determine meteorological optical range (MOR), and measure the number of particles in the atmosphere. Relationships between typical opticalmore » quality metrics, MOR values, and total number of fog particles are described using the data obtained from the fog chamber and repeated over a series of three tests.« less

ORANGES evaluation test plans : analysis of before data collected for the US DOT sponsored evaluation of the ORANGES electronic payment systems field operational test

DOT National Transportation Integrated Search

2003-10-02

This document is one of a series of working papers that report on progress for the US DOT evaluation for Phase I of the ORANGES field operational test. Each working paper corresponds to a Phase I task. At the conclusion of Phase I, these documents wi...

Contact Dermatitis to Personal Sporting Equipment in Youth.

PubMed

Marzario, Barbara; Burrows, Dianne; Skotnicki, Sandy

2016-07-01

Contact dermatitis to personal sporting equipment in youth is poorly studied. To review the results of patch testing 6 youth to their sporting equipment in a dermatology general private practice from 2006 to 2011. A retrospective analysis of 6 youth aged 11 to 14 who were evaluated for chronic and persistent dermatitis occurring in relation to sports equipment was conducted. All patients were subjected to epicutaneous (patch) testing, which included some or all of the following: North American Contact Dermatitis Group (NACGD) series, textile series, rubber series, corticosteroid series, and raw material from the patients' own personal equipment. All cases had 1 or more positive patch test reactions to an allergen within the aforementioned series, and 3 subjects tested positive to their personal equipment in raw form. Allergic contact dermatitis, not irritant, was deemed the relevant cause of chronic dermatitis in 4 of the 6 patients due to positive reactions to epicutaneous tests and/or personal equipment. The utility of testing to patients' own sporting equipment was shown to be of additional value and should be considered when patch testing for contact allergy to sporting equipment. © The Author(s) 2015.

A videotape series for teaching physicians to evaluate sexually abused children.

PubMed

Jones, Jerry G; Garrett, Judy; Worthington, Toss

2004-01-01

A free videotape subscription series was utilized to increase the knowledge of general physicians in clinical practice about the medical evaluation of sexually abused children. Of the 65 physicians who requested the first tape, 39 (60%) completed it. Fourteen of the 39 physicians who completed the first tape (36%) completed the 5-tape series. Completion data suggested that series completion was unrelated to prior knowledge, years since training or number of sexual abuse examinations performed in the previous year. Evaluative comments suggested that quality of the tapes was not a factor in completion rate. On tests of immediate retention, the average posttest percent correct was significantly higher than on the pretest. In a 3-year follow-up of the 14 physicians who completed the series, 10 reported that they were still performing sexual abuse examinations.

Contact Urticaria to Nickel: A Series of 11 Patients Who Were Prick Test Positive and Patch Test Negative to Nickel Sulfate 2.5% and 5.0.

PubMed

Saluja, Sandeep S; Davis, Crystal L; Chong, Tracie A; Powell, Douglas L

2016-01-01

Nickel is the most common allergen found by patch testing; however, not all cases of nickel allergy are type 4 (delayed) allergies. Contact urticaria (CU) to nickel (immediate reaction) has been reported; however, few seem to evaluate it as per a recent published survey of American Contact Dermatitis Society members. The aim of the study was to present a series of patients who had clinical histories suggestive of nickel allergy and yet were patch test negative but prick test positive to nickel, thus demonstrating CU. We reviewed the charts of 11 patients who were patch test negative but prick test positive. All 11 patients demonstrated evidence of CU by prick testing (or closed chamber test in 1). None were patch test positive to nickel 2.5% or 5.0%. Four patients' histories mentioned reactions to various jewelry/earrings within minutes, whereas 2 histories mentioned reacting within a few hours. These histories are consistent with CU. Others (except 1 patient) recalled reacting to jewelry/earrings but did not recall a time frame. Our series suggests that CU to nickel may be far more common than anticipated and should be evaluated with prick testing when patients' history suggests nickel allergy and yet they are patch test negative.

ASBESTOS IN DRINKING WATER PERFORMANCE EVALUATION STUDIES

EPA Science Inventory

Performance evaluations of laboratories testing for asbestos in drinking water according to USEPA Test Method 100.1 or 100.2 are complicated by the difficulty of providing stable sample dispersions of asbestos in water. Reference samples of a graduated series of chrysotile asbes...

ASBESTOS IN DRINKING WATER PERFORMANCE EVALUATION STUDIES

EPA Science Inventory

Performance evaluations of laboratories testing for asbestos in drinking water according to USEPA Test Method 100.1 or 100.2 are complicated by the difficulty of providing stable sample dispersions of asbestos in water. Reference samples of a graduated series of chrysotile asbest...

Identifying Autocorrelation Generated by Various Error Processes in Interrupted Time-Series Regression Designs: A Comparison of AR1 and Portmanteau Tests

ERIC Educational Resources Information Center

Huitema, Bradley E.; McKean, Joseph W.

2007-01-01

Regression models used in the analysis of interrupted time-series designs assume statistically independent errors. Four methods of evaluating this assumption are the Durbin-Watson (D-W), Huitema-McKean (H-M), Box-Pierce (B-P), and Ljung-Box (L-B) tests. These tests were compared with respect to Type I error and power under a wide variety of error…

Aircraft Survivability: Live Fire Test and Evaluation, Spring 2010

DTIC Science & Technology

2010-01-01

OCPD ). These devices were examined in this program for their potential to reduce fire vulnerability. Testing for this test series, designated Live...divided into three categories: 1) short circuit, 2) separating arc gap, and 3) 90% conductor diameter reduction. The performance of the OCPDs was also...incorporated a production- representative tank configuration. All test configurations were evaluated with OCPD protection. In ballistic damage tests

Standard Test Methods for Textile Composites

NASA Technical Reports Server (NTRS)

Masters, John E.; Portanova, Marc A.

1996-01-01

Standard testing methods for composite laminates reinforced with continuous networks of braided, woven, or stitched fibers have been evaluated. The microstructure of these textile' composite materials differs significantly from that of tape laminates. Consequently, specimen dimensions and loading methods developed for tape type composites may not be applicable to textile composites. To this end, a series of evaluations were made comparing testing practices currently used in the composite industry. Information was gathered from a variety of sources and analyzed to establish a series of recommended test methods for textile composites. The current practices established for laminated composite materials by ASTM and the MIL-HDBK-17 Committee were considered. This document provides recommended test methods for determining both in-plane and out-of-plane properties. Specifically, test methods are suggested for: unnotched tension and compression; open and filled hole tension; open hole compression; bolt bearing; and interlaminar tension. A detailed description of the material architectures evaluated is also provided, as is a recommended instrumentation practice.

Hydrogen-oxygen catalytic ignition and thruster investigation. Volume 2: High pressure thruster evaluations

NASA Technical Reports Server (NTRS)

Johnson, R. J.; Heckert, B.; Burge, H. L.

1972-01-01

A high pressure thruster effort was conducted with the major objective of demonstrating a duct cooling concept with gaseous propellant in a thruster operating at nominally 300 psia and 1500 lbf. The analytical design methods for the duct cooling were proven in a series of tests with both ambient and reduced temperature propellants. Long duration tests as well as pulse mode tests demonstrated the feasibility of the concept. All tests were conducted with a scaling of the raised post triplet injector design previously demonstrated at 900 lbf in demonstration firings. A series of environmental conditioned firings were also conducted to determine the effects of thermal soaks, atmospheric air and high humidity. This volume presents the results of the high pressure thruster evaluations.

Design and testing of an energy-absorbing crewseat for the F/FB-111 aircraft. Volume 2: Data from seat testing

NASA Technical Reports Server (NTRS)

Shane, S. J.

1985-01-01

The unacceptably high injury rate during the escape sequence (including the ejection and ground impact) of the crew module for F/FB-111 aircraft is reviewed. A program to determine if the injury potential could be reduced by replacing the existing crewseats with energy absorbing crewseats is presented. An energy absorbing test seat is designed using much of the existing seat hardware. An extensive dynamic seat test series, designed to duplicate various crew module ground impact conditions is conducted at a sled test facility. Comparative tests with operational F-111 crewseats are also conducted. After successful dynamic testing of the seat, more testing is conducted with the seats mounted in an F-111 crew module. Both swing tests and vertical drop tests are conducted. The vertical drop tests are used to obtain comparative data between the energy absorbing and operational seats. Volume 1 describes the energy absorbing test seat and testing conducted, and evaluates the data from both test series. Volume 2 presents the data obtained during the seat test series, while Volume 3 presents the data from the crew module test series.

Fuel containment and damage tolerance in large composite primary aircraft structures. Phase 2: Testing

NASA Technical Reports Server (NTRS)

Sandifer, J. P.; Denny, A.; Wood, M. A.

1985-01-01

Technical issues associated with fuel containment and damage tolerance of composite wing structures for transport aircraft were investigated. Material evaluation tests were conducted on two toughened resin composites: Celion/HX1504 and Celion/5245. These consisted of impact, tension, compression, edge delamination, and double cantilever beam tests. Another test series was conducted on graphite/epoxy box beams simulating a wing cover to spar cap joint configuration of a pressurized fuel tank. These tests evaluated the effectiveness of sealing methods with various fastener types and spacings under fatigue loading and with pressurized fuel. Another test series evaluated the ability of the selected coatings, film, and materials to prevent fuel leakage through 32-ply AS4/2220-1 laminates at various impact energy levels. To verify the structural integrity of the technology demonstration article structural details, tests were conducted on blade stiffened panels and sections. Compression tests were performed on undamaged and impacted stiffened AS4/2220-1 panels and smaller element tests to evaluate stiffener pull-off, side load and failsafe properties. Compression tests were also performed on panels subjected to Zone 2 lightning strikes. All of these data were integrated into a demonstration article representing a moderately loaded area of a transport wing. This test combined lightning strike, pressurized fuel, impact, impact repair, fatigue and residual strength.

Evaluation of random errors in Williams’ series coefficients obtained with digital image correlation

NASA Astrophysics Data System (ADS)

Lychak, Oleh V.; Holyns'kiy, Ivan S.

2016-03-01

The use of the Williams’ series parameters for fracture analysis requires valid information about their error values. The aim of this investigation is the development of the method for estimation of the standard deviation of random errors of the Williams’ series parameters, obtained from the measured components of the stress field. Also, the criteria for choosing the optimal number of terms in the truncated Williams’ series for derivation of their parameters with minimal errors is proposed. The method was used for the evaluation of the Williams’ parameters, obtained from the data, and measured by the digital image correlation technique for testing a three-point bending specimen.

Development and Evaluation of Titanium Space Suit Bearings

NASA Technical Reports Server (NTRS)

Rhodes, Richard; Battisti, Brian; Ytuarte, Ray, Jr.; Schultz, Bradley

2016-01-01

The Z-2 Prototype Planetary Extravehicular Space Suit Assembly is a continuation of NASA's Z series of spacesuits, designed with the intent of meeting a wide variety of exploration mission objectives, including human exploration of the Martian surface. Incorporating titanium bearings into the Z series space suit architecture allows us to reduce mass by an estimated 23 pounds per suit system compared to the previously used stainless steel bearing designs without compromising suit functionality. There are two obstacles to overcome when using titanium for a bearing race: 1) titanium is flammable when exposed to the oxygen wetted environment inside the space suit and 2) titanium's poor wear properties are often challenging to overcome in tribology applications. In order to evaluate the ignitability of a titanium space suit bearing, a series of tests were conducted at White Sands Test Facility that introduced the bearings to an extreme test profile, with multiple failures imbedded into the test bearings. The testing showed no signs of ignition in the most extreme test cases; however, substantial wear of the bearing races was observed. In order to design a bearing that can last an entire exploration mission (approximately 2 years), bearing test rigs were developed that allow for the quick evaluation of various bearing ball loads, ball diameters, lubricants, and surface treatments. This test data will allow designers to minimize the titanium bearing mass for a specific material and lubricant combination around a maximum contact stress that will allow the bearing to survive the life of an exploration mission. This paper reviews the current research and testing that has been performed on titanium bearing races to evaluate the use of such materials in an enriched oxygen environment and to optimize the bearing assembly mass and tribological properties to accommodate for the high bearing cycle life for an exploration mission.

Non-parametric characterization of long-term rainfall time series

NASA Astrophysics Data System (ADS)

Tiwari, Harinarayan; Pandey, Brij Kishor

2018-03-01

The statistical study of rainfall time series is one of the approaches for efficient hydrological system design. Identifying, and characterizing long-term rainfall time series could aid in improving hydrological systems forecasting. In the present study, eventual statistics was applied for the long-term (1851-2006) rainfall time series under seven meteorological regions of India. Linear trend analysis was carried out using Mann-Kendall test for the observed rainfall series. The observed trend using the above-mentioned approach has been ascertained using the innovative trend analysis method. Innovative trend analysis has been found to be a strong tool to detect the general trend of rainfall time series. Sequential Mann-Kendall test has also been carried out to examine nonlinear trends of the series. The partial sum of cumulative deviation test is also found to be suitable to detect the nonlinear trend. Innovative trend analysis, sequential Mann-Kendall test and partial cumulative deviation test have potential to detect the general as well as nonlinear trend for the rainfall time series. Annual rainfall analysis suggests that the maximum changes in mean rainfall is 11.53% for West Peninsular India, whereas the maximum fall in mean rainfall is 7.8% for the North Mountainous Indian region. The innovative trend analysis method is also capable of finding the number of change point available in the time series. Additionally, we have performed von Neumann ratio test and cumulative deviation test to estimate the departure from homogeneity. Singular spectrum analysis has been applied in this study to evaluate the order of departure from homogeneity in the rainfall time series. Monsoon season (JS) of North Mountainous India and West Peninsular India zones has higher departure from homogeneity and singular spectrum analysis shows the results to be in coherence with the same.

Examining the Internal Validity and Statistical Precision of the Comparative Interrupted Time Series Design by Comparison with a Randomized Experiment

ERIC Educational Resources Information Center

St.Clair, Travis; Cook, Thomas D.; Hallberg, Kelly

2014-01-01

Although evaluators often use an interrupted time series (ITS) design to test hypotheses about program effects, there are few empirical tests of the design's validity. We take a randomized experiment on an educational topic and compare its effects to those from a comparative ITS (CITS) design that uses the same treatment group as the experiment…

Refinement of Reading and Mathematics Test Through an Analysis of Reactivity. Beginning Teacher Evaluation Study. Technical Report Series. Technical Report III-6.

ERIC Educational Resources Information Center

Filby, Nikola N.; Dishaw, Marilyn

Major analyses of the achievement tests used in the Beginning Teacher Evaluation Study were conducted to determine test reactivity to instruction. Reading and mathematics tests were administered to second and fifth grade children. Classroom teachers' records were examined to determine the amount of opportunity students had to learn the content…

Evaluation of the LMA (Trade Name) Series of Wire Rope Testing Instruments

DTIC Science & Technology

1985-09-30

NSWC TR 85-388 EVALUATION OF THE LMATM SERIES OF WIRE N ROPE TESTING INSTRUMENTS N BY PAUL M. GAMMELL (NSWC) LARRY D. UNDERBAKKE (NCEL) RESEARCH AND...TECHNOLOGY DEPARTMENT 30 SEPTEMBER 1985’ < DTIC l LECTE Aji~p ro t lu f j t) I c rv I o. s ( st rhtI IiT oi i ts n m itedi1 8 1 JON- NAVAL SURFACE...AUTHOR(S) Gammell, Paul M. (NSWC) and Underbakke, Larry D. (NCEL) 13a. TYPE OF REPORT 13b. TIME COVERED 14. DATE OF REPORT (Year, Month, Day) S. PAGE

The Evaluation of Contact Sensitivity with Standard and Cosmetic Patch Test Series in Rosacea Patients

PubMed Central

Bulur, Isil; Saracoglu, Zeynep Nurhan; Bilgin, Muzaffer

2018-01-01

Background Rosacea is a common dermatosis characterized by erythema, telangiectasia, papules and pustules. Objective We aimed to evaluate contact sensitivity in the rosacea patients. Methods We included 65 rosacea patients and 60 healthy volunteers in the study. The patient and control groups were patch tested with European baseline series and cosmetic series. Results A positive reaction to at least 1 allergen in the European standard series was found in 32.3% of rosacea patients and 20.0% of subjects in the control group while the relevant numbers were 30.8% of rosacea patients and 10% of controls with the cosmetic series (p=0.08). In total, we found a positive reaction to at least 1 allergen in 38.5% of patients and 25.0% of controls (p=0.15). We did not find a statistically significant relationship between a positive reaction to 1 allergen in total and the gender, skin type, rosacea type, ocular involvement, age and disease duration. There were more symptoms in patients with a positive reaction to allergens (p<0.001). Conclusion Contact sensitivity was detected more common in rosacea patients. Patch testing may be useful in the treatment and follow up of rosacea patients especially if symptoms such as itching, burning and stinging are present. PMID:29853742

The Evaluation of Contact Sensitivity with Standard and Cosmetic Patch Test Series in Rosacea Patients.

PubMed

Erdogan, Hilal Kaya; Bulur, Isil; Saracoglu, Zeynep Nurhan; Bilgin, Muzaffer

2018-06-01

Rosacea is a common dermatosis characterized by erythema, telangiectasia, papules and pustules. We aimed to evaluate contact sensitivity in the rosacea patients. We included 65 rosacea patients and 60 healthy volunteers in the study. The patient and control groups were patch tested with European baseline series and cosmetic series. A positive reaction to at least 1 allergen in the European standard series was found in 32.3% of rosacea patients and 20.0% of subjects in the control group while the relevant numbers were 30.8% of rosacea patients and 10% of controls with the cosmetic series ( p =0.08). In total, we found a positive reaction to at least 1 allergen in 38.5% of patients and 25.0% of controls ( p =0.15). We did not find a statistically significant relationship between a positive reaction to 1 allergen in total and the gender, skin type, rosacea type, ocular involvement, age and disease duration. There were more symptoms in patients with a positive reaction to allergens ( p <0.001). Contact sensitivity was detected more common in rosacea patients. Patch testing may be useful in the treatment and follow up of rosacea patients especially if symptoms such as itching, burning and stinging are present.

Strategy for Alternative Occupant Volume Testing

DOT National Transportation Integrated Search

2009-10-20

This paper describes plans for a series of quasi-static : compression tests of rail passenger equipment. These tests are : designed to evaluate the strength of the occupant volume under : static loading conditions. The research plan includes a detail...

AGARD Flight Test Techniques Series. Volume 8. Flight Testing under Extreme Environmental Conditions

DTIC Science & Technology

1988-01-01

gravity control system operation. The overall objective of fuel system tests is to determine whether the system functions properly at all conditions both... gravity . 3.3.4 Hydraulic System The functional adequacy of the hydraulic system should be evaluated by monitoring operating system temperatures and...mechanical or gravity function of the crew ladder should be evaluated. The ladder should be exposed to freasing rain and icing to evaluate the non

The Impact of Proposed Radio Frequency Radiation Standards on Military Operations.

DTIC Science & Technology

1985-03-01

psychological testing has been accomplished on a number of the overexposees. The evaluators have, on occasion, attempted to draw some conclusions, but...NEUILLY- 6i UCAED THELLE E .MR 5hhhhI-0 /G618Eh1hEEhhhmhlhEmqhh 11. 11111 1.1 6 MICROCOPY RESOLUTION TEST CHART NATIONAL BUREAU OF STANDARDS 1963-A tod...series lasting approximately 3 to 4 minutes. Since the average of the staircase current during the period of each series of tests was slightly below the

Progress Report on Reactivity Analyses (October-December Test Data). Beginning Teacher Evaluation Study. Technical Note Series. Technical Note III-5.

ERIC Educational Resources Information Center

Filby, Nikola N.

The development and refinement of the measures of student achievement in reading and mathematics for the Beginning Teacher Evaluation Study are described. The concept of reactivity to instruction is introduced: the tests used to evaluate instructional processes must be sensitive indicators of classroom learning overtime. Data collection activities…

Superfund Technology Evaluation Report: SITE Program Demonstration Test Shirco Pilot-Scale Infrared Incineration System at the Rose Township Demode Road Superfund Site Volume I

EPA Science Inventory

The Shirco Pilot-Scale Infrared Incineration System was evaluated during a series of seventeen test runs under varied operating conditions at the Demode Road Superfund Site located in Rose Township, Michigan. The tests sought to demonstrate the effectiveness of the unit and the t...

10 CFR 709.2 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-01-01

... test data analysis phase, and the post-test phase. Polygraph examination records means all records of... DOE's National Nuclear Security Administration. No opinion means an evaluation of a polygraph test by... test) during a specific series of interactions, including the pretest interview, the use of the...

10 CFR 709.2 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-01-01

... test data analysis phase, and the post-test phase. Polygraph examination records means all records of... DOE's National Nuclear Security Administration. No opinion means an evaluation of a polygraph test by... test) during a specific series of interactions, including the pretest interview, the use of the...

10 CFR 709.2 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-01-01

... test data analysis phase, and the post-test phase. Polygraph examination records means all records of... DOE's National Nuclear Security Administration. No opinion means an evaluation of a polygraph test by... test) during a specific series of interactions, including the pretest interview, the use of the...

Is the European standard series suitable for patch testing in Riyadh, Saudi Arabia?

PubMed

el-Rab, M O; al-Sheikh, O A

1995-11-01

Due to the lack of a regional patch test series in our geographical area, the suitability of the European standard series was evaluated by patch testing dermatitis patients in Riyadh, Saudi Arabia. Of 240 consecutive patients with various forms of dermatitis, 136 (57%) showed 1 or more positive patch tests, women, 74 (54%), slightly outnumbering men, 62 (46%). Positive reactions were found to 21 of the 22 items in the test series. Sensitization was most common to nickel sulfate (51 = 37.5%), potassium dichromate (48 = 35%) and cobalt chloride (43 = 32%) The frequency of sensitization to nickel was higher in women (41 = 30%) while that to dichromate was higher in men (39 = 29%). Less reactions were found to fragrance mix (21 = 15%), formaldehyde (15 = 11%) and neomycin sulfate (15 = 11%). Sensitization to other allergens ranged between 10 and 1%. Less than 1% of patients (0.7%) reacted to benzocaine and none to primin. The frequency of occurrence of multiple sensitivities is also presented. We conclude that the European standard series is suitable for patch testing dermatitis patients in our region, with the exception of benzocaine and primin. The addition of 3 allergens that could be of local relevance is discussed.

Evaluation of anomalies observed on film from S-190A flight system calibration test

NASA Technical Reports Server (NTRS)

Bourque, P. F.; Perry, L.; Sauer, G. E.

1975-01-01

Due to a persistent problem of scratched film from testing of the Skylab S-190A system, a series of tests were designed to identify the cause of the film scratching. The procedures followed in this test for pretest handling and packaging of the film, the makeup of the rolls for processing, and the results of the processed film evaluation are reported.

Bio-Contamination Control for Spacesuit Garments - A Preliminary Study

NASA Technical Reports Server (NTRS)

Rhodes, Richard; Korona, Adam; Orndoff, Evelyn; Ott, Mark; Poritz, Darwin

2010-01-01

This paper outlines a preliminary study to review, test, and improve upon the current state of spacesuit bio-contamination control. The study includes an evaluation of current and advanced suit materials, ground and on-orbit cleaning methods, and microbial test and analysis methods. The first aspect of this study was to identify potential anti-microbial textiles and cleaning agents, and to review current microbial test methods. The anti-microbial cleaning agent and textile market survey included a review of current commercial-off-the-shelf (COTS) products that could potentially be used as future space flight hardware. This review included replacements for any of the softgood layers that may become contaminated during an extravehicular activity (EVA), including the pressure bladder, liquid cooling garment, and ancillary comfort undergarment. After a series of COTS anti-microbial textiles and clean ing agents were identified, a series of four tests were conducted: (1) a stacked configuration test that was conducted in order to review how bio-contamination would propagate through the various suit layers, (2) a individual materials test that evaluated how well each softgood layer either promoted or repressed growth, (3) a cleaning agent test that evaluated the efficacy on each of the baseline bladders, and (4) an evaluation of various COTS anti-microbial textiles. All antimicrobial COTS materials tested appeared to control bacteria colony forming unit (CFU) growth better than the Thermal Comfort Undergarment (TCU) and ACES Liquid Cooling Garment (LCG)/EMU Liquid Cooling Ventilation Garment (LCVG) materials currently in use. However, a comparison of fungi CFU growth in COTS to current suit materials appeared to vary per material. All cleaning agents tested in this study appeared to inhibit the level of bacteria and fungi growth to acceptable levels for short duration tests. While several trends can be obtained from the current analysis, a series of test improvements are described for future microbial testing.

75 FR 55159 - Science and Technology Reinvention Laboratory (STRL) Personnel Management Demonstration Project...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-09-09

.... Above GS-15 Positions B. Classification 1. Occupational Series 2. Classification Standards and Position... Duty Locations Appendix B: Occupational Series by Occupational Family Appendix C: Intervention Model..., MD; Lakehurst, NJ; and Orlando, FL. These facilities support research, development, test, evaluation...

Is a specific eyelid patch test series useful? Results of a French prospective study.

PubMed

Assier, Haudrey; Tetart, Florence; Avenel-Audran, Martine; Barbaud, Annick; Ferrier-le Bouëdec, Marie-Christine; Giordano-Labadie, Françoise; Milpied, Brigitte; Amsler, Emmanuelle; Collet, Evelyne; Girardin, Pascal; Soria, Angèle; Waton, Julie; Truchetet, François; Bourrain, Jean-Luc; Gener, Gwendeline; Bernier, Claire; Raison-Peyron, Nadia

2018-06-08

Eyelids are frequent sites of contact dermatitis. No prospective study focused on eyelid allergic contact dermatitis (EACD) has yet been published, and this topic has never been studied in French patients. To prospectively evaluate the usefulness of an eyelid series in French patients patch tested because of EACD, and to describe these patients. We prospectively analysed standardized data for all patients referred to our departments between September 2014 and August 2016 for patch testing for suspected EACD as the main reason. All patients were patch tested with an eyelid series, the European baseline series (EBS), the French additional series, and their personal products. Patch testing with additional series and repeated open application tests (ROATs) or open tests were performed if necessary. A standardized assessment of the relevance was used, and the analysis of the results was focused on patients having positive test results with a current certain relevance. Two-hundred and sixty-four patients (238 women and 26 men) were included. Three-hundred and twenty-two tests gave positive results in 167 patients, 84 of whom had currently relevant reactions: 56 had currently relevant positive test reactions to the EBS, 16 had currently relevant positive test reactions to their personal products, 8 had currently relevant positive test reactions to the French additional series, and 4 had currently relevant positive test reactions to the eyelid series. Sixty-seven per cent of all relevant cases were related to cosmetic products. The most frequent allergens with current relevance were methylisothiazolinone (10.2%), fragrance mix I (3%), nickel (2.7%), hydroxyperoxides of linalool (2.7%) and limonene (2.3%), and Myroxylon pereirae (2.3%). Current atopic dermatitis was found in 9.5% of patients. The duration of dermatitis was shorter (23.2 vs 34.2 months; P = .035) in patients with currently relevant test reactions. The percentage of currently relevant tests remained the same when atopic patients or dermatitis localized only on the eyelids were taken into account. In French patients, testing for EACD with the extended baseline series and personal products, also including ROATs and use tests, appears to be adequate, considering the currently relevant positive test reactions. The regular addition of an eyelid series does not seem to be necessary. © 2018 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Hydraulic and environmental behavior of recycled asphalt pavement in highway shoulder applications

DOT National Transportation Integrated Search

2017-10-01

Hydraulic conductivity of seven recycled asphalt pavement materials (RAPs) was evaluated through a series of constant-head tests, while their leaching potential was determined through batch leach tests and column leach tests. The contaminant transpor...

Un Test contrastif oral pour l'evaluation des difficultes lexicales dans l'apprentissage de l'anglais L2 (An Oral Contrastive Test for the Evaluation of Lexical Difficulties in Learning English as a Second Language).

ERIC Educational Resources Information Center

Haeusser, Christiane

1978-01-01

The test described here is a particular type of diagnostic test; it is part of a series of tests designed to explore systematically areas of potential lexical difficulty in the English language for French-speaking students of English. The lexical units are considered under their formal, morphological, syntactic and semantic aspects. The test has…

Development and Evaluation of Vocational Competency Measures. Final Report.

ERIC Educational Resources Information Center

Chalupsky, Albert B.; And Others

A series of occupational competency tests representing all seven vocational education curriculum areas were developed, field tested, and validated. Seventeen occupations were selected for competency test development: agricultural chemicals applications technician, farm equipment mechanic, computer operator, word processing specialist, apparel…

Boeing's CST-100 Structural Test Article Shipment from C3PF to B

NASA Image and Video Library

2016-11-22

Boeing’s Structural Test Article of its CST-100 Starliner spacecraft is moved out of the company’s Commercial Crew and Cargo Processing Facility at NASA’s Kennedy Space Center on its way to Huntington Beach, California, for evaluations. Built to the specifications of an operational spacecraft, the STA is intended to be evaluated through a series of thorough testing conditions.

Blasting Rocks and Blasting Cars: Applied Engineering (LBNL Summer Lecture Series)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hopkins, Deborah

2004-06-30

Summer Lecture Series 2004: Deb Hopkins works with industries like automobile, mining and paper to improve their evaluation and measuring techniques. For several years, she has coordinated a program at Berkeley Lab funded under the Partnership for a New Generation of Vehicles, a collaboration between the federal government and the U.S. Council for Automotive Research. Nondestructive evaluation techniques to test a car's structural integrity are being developed for auto assembly lines.

Evaluation of Nonlinear Constitutive Properties of Concrete

DTIC Science & Technology

1990-02-01

34 " \\ 19:#BSTRACT (Continue on reverse if necesuar 4nd identify by block number) 3his report describes the development of a methodology that allows for...Continued). The method of evaluation, as developed herein, consists of the following steps: 1. The design and execution of a series of material... developed in Step L. 3. Design and execution of the series of verification tests which provide data suffi- cient for defining key complex material

Blasting Rocks and Blasting Cars: Applied Engineering (LBNL Summer Lecture Series)

ScienceCinema

Hopkins, Deborah [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States). Engineering Division

2017-12-09

Summer Lecture Series 2004: Deb Hopkins works with industries like automobile, mining and paper to improve their evaluation and measuring techniques. For several years, she has coordinated a program at Berkeley Lab funded under the Partnership for a New Generation of Vehicles, a collaboration between the federal government and the U.S. Council for Automotive Research. Nondestructive evaluation techniques to test a car's structural integrity are being developed for auto assembly lines.

Caustic stress corrosion tests for the LLTR

DOE Office of Scientific and Technical Information (OSTI.GOV)

Indig, M.E.

1976-05-01

A series of tests have been performed in order to determine the effects of the caustic resulting from the Na/H/sub 2/O reaction on the materials used in the LLTR-MSG series of testing. Stainless steel, 2 /sup 1///sub 4/ Cr--1 Mo and carbon steel have been evaluated. Stress corrosion cracking susceptibility and general corrosion are reported. Over the range of temperature, caustic concentration and heating rate tested the stainless steel stressed to 90% of yield or above suffered cracking. Whereas, the 2-/sup 1///sub 4/ Cr--1 Mo and carbon steel were not cracked.

Evaluation of Canadian undergraduate ophthalmology medical education at Western University.

PubMed

Li, Bo; Curts, Dustin; Iordanous, Yiannis; Proulx, Alain; Sharan, Sapna

2016-10-01

To assess and evaluate the current level of ophthalmology knowledge and teaching curriculum in undergraduate year 3 (MS-3) at Western University. The Undergraduate Medical Education Curriculum at Western University has instituted additional ophthalmology lecture series to all MS-3 students. A test on basic ophthalmic knowledge was administered to MS-3 students immediately before and after lecture series to evaluate the level of knowledge at baseline and after ophthalmology didactic teaching. An evaluation survey was also given to MS-3 students to assess students' self-perceived level of competency, exposure, and interests in ophthalmology. A total of 134 students attended the ophthalmology lecture series in the study, and 88.1% of students completed the pretest, post-test, and Ophthalmology Education Survey. The average pretest and post-test scores were 40.7% and 75.6% (p < 0.01), respectively. The average rating from MS-3 students for ophthalmology exposure during medical school education was 2.11 (1 = "very minimal" and 5 = "more than adequate"). The average rating for desire for additional didactic ophthalmology lectures was 4.02 (1 = "strongly disagree" and 5 = "strongly agree"). The average rating for interest in ophthalmology was 2.74 (1 = "very little interest" and 5 = "very strong interest"). The additional ophthalmology lecture series had a positive impact on the level of ophthalmic knowledge among MS-3 students, and a strong desire for more ophthalmology teaching during medical school education was identified, as evidenced by the survey undertaken by students after the lectures. Copyright © 2016 Canadian Ophthalmological Society. Published by Elsevier Inc. All rights reserved.

Space Suit Portable Life Support System (PLSS) 2.0 Pre-Installation Acceptance (PIA) Testing

NASA Technical Reports Server (NTRS)

Anchondo, Ian; Cox, Marlon; Meginnis, Carly; Westheimer, David; Vogel, Matt R.

2016-01-01

Following successful completion of the space suit Portable Life Support System (PLSS) 1.0 development and testing in 2011, the second system-level prototype, PLSS 2.0, was developed in 2012 to continue the maturation of the advanced PLSS design. This advanced PLSS is intended to reduce consumables, improve reliability and robustness, and incorporate additional sensing and functional capabilities over the current Space Shuttle/International Space Station Extravehicular Mobility Unit (EMU) PLSS. PLSS 2.0 represents the first attempt at a packaged design comprising first generation or later component prototypes and medium fidelity interfaces within a flight-like representative volume. Pre-Installation Acceptance (PIA) is carryover terminology from the Space Shuttle Program referring to the series of test sequences used to verify functionality of the EMU PLSS prior to installation into the Space Shuttle airlock for launch. As applied to the PLSS 2.0 development and testing effort, PIA testing designated the series of 27 independent test sequences devised to verify component and subsystem functionality, perform in situ instrument calibrations, generate mapping data, define set-points, evaluate control algorithms, evaluate hardware performance against advanced PLSS design requirements, and provide quantitative and qualitative feedback on evolving design requirements and performance specifications. PLSS 2.0 PIA testing was carried out in 2013 and 2014 using a variety of test configurations to perform test sequences that ranged from stand-alone component testing to system-level testing, with evaluations becoming increasingly integrated as the test series progressed. Each of the 27 test sequences was vetted independently, with verification of basic functionality required before completion. Because PLSS 2.0 design requirements were evolving concurrently with PLSS 2.0 PIA testing, the requirements were used as guidelines to assess performance during the tests; after the completion of PIA testing, test data served to improve the fidelity and maturity of design requirements as well as plans for future advanced PLSS functional testing.

Human Factors Experiments for Data Link : Interim Report No. 5

DOT National Transportation Integrated Search

1975-02-01

One and two-man crews of general aviation pilots and two-man crews of FAA/NAFEC test pilots made a series of simulated flights in a GAT-2 simulator to evaluate various complements of I/O equipment for Data Link. In the earlier experiments in the seri...

Evaluation of Propellant Erosivity with Vented Erosion Apparatus

DTIC Science & Technology

1981-03-01

decision, unless so designated by other documentation. Destroy this report when no longer needed. Do not return it to the originator. UNCLASSIFIED...of specimens 1 and 2. This type of variation is typical of that observed in the previous eperimental series. The fourth test in each series was

NEUROBEHAVIORAL TESTING IN ANIMALS AND THE APPLICATION TO RISK ASSESSMENT.

EPA Science Inventory

Neurobehavioral evaluations are emerging as a key component in neurotoxicity testing. The tests most often used for screening are the functional observational battery (FOB) and motor activity. The FOB is a series of non-invasive observational and manipulative measures which ass...

Comparison of test protocols for standard room/corner tests

Treesearch

R. H. White; M. A. Dietenberger; H. Tran; O. Grexa; L. Richardson; K. Sumathipala; M. Janssens

1998-01-01

As part of international efforts to evaluate alternative reaction-to-fire tests, several series of room/comer tests have been conducted. This paper reviews the overall results of related projects in which different test protocols for standard room/corner tests were used. Differences in the test protocols involved two options for the ignition burner scenario and whether...

Vortex sensing tests at NAFEC.

DOT National Transportation Integrated Search

1972-01-01

The report describes the results of a series of tests to determine and evaluate three experimental techniques for remote sensing of the wing-tip vortices generated by heavy commercial and military aircraft. These techniques involved a pulsed, bistati...

Process fault detection and nonlinear time series analysis for anomaly detection in safeguards

DOE Office of Scientific and Technical Information (OSTI.GOV)

Burr, T.L.; Mullen, M.F.; Wangen, L.E.

In this paper we discuss two advanced techniques, process fault detection and nonlinear time series analysis, and apply them to the analysis of vector-valued and single-valued time-series data. We investigate model-based process fault detection methods for analyzing simulated, multivariate, time-series data from a three-tank system. The model-predictions are compared with simulated measurements of the same variables to form residual vectors that are tested for the presence of faults (possible diversions in safeguards terminology). We evaluate two methods, testing all individual residuals with a univariate z-score and testing all variables simultaneously with the Mahalanobis distance, for their ability to detect lossmore » of material from two different leak scenarios from the three-tank system: a leak without and with replacement of the lost volume. Nonlinear time-series analysis tools were compared with the linear methods popularized by Box and Jenkins. We compare prediction results using three nonlinear and two linear modeling methods on each of six simulated time series: two nonlinear and four linear. The nonlinear methods performed better at predicting the nonlinear time series and did as well as the linear methods at predicting the linear values.« less

Business Telephone Etiquette. Comptetency Test Package. Office Occupations. Instructor's Guide.

ERIC Educational Resources Information Center

Hines, Donna

This competency test package, one of a series of test packages for office occupations education, contains a list of performance objectives: a sample, 50-point objective test; and several performance test activities. The package also includes complete directions for the student and the instructor, plus answer keys and a guide for evaluating the…

Taurus II Stage Test Simulations: Using Large-Scale CFD Simulations to Provide Critical Insight into Plume Induced Environments During Design

NASA Technical Reports Server (NTRS)

Struzenberg, L. L.; West, J. S.

2011-01-01

This paper describes the use of targeted Loci/CHEM CFD simulations to evaluate the effects of a dual-engine first-stage hot-fire test on an evolving integrated launch pad/test article design. This effort was undertaken as a part of the NESC Independent Assessment of the Taurus II Stage Test Series. The underlying conceptual model included development of a series of computational models and simulations to analyze the plume induced environments on the pad, facility structures and test article. A pathfinder simulation was first developed, capable of providing quick-turn around evaluation of plume impingement pressures on the flame deflector. Results from this simulation were available in time to provide data for an ongoing structural assessment of the deflector. The resulting recommendation was available in a timely manner and was incorporated into construction schedule for the new launch stand under construction at Wallops Flight Facility. A series of Reynolds-Averaged Navier-Stokes (RANS) quasi-steady simulations representative of various key elements of the test profile was performed to identify potential concerns with the test configuration and test profile. As required, unsteady Hybrid-RANS/LES simulations were performed, to provide additional insight into critical aspects of the test sequence. Modifications to the test-specific hardware and facility structures thermal protection as well as modifications to the planned hot-fire test profile were implemented based on these simulation results.

Development and Evaluation of Titanium Spacesuit Bearings

NASA Technical Reports Server (NTRS)

Rhodes, Richard; Battisti, Brian; Ytuarte, Raymond, Jr.; Schultz, Bradley

2016-01-01

The Z-2 Prototype Planetary Extravehicular Space Suit Assembly is a continuation of NASA's Z-series of spacesuits, designed with the intent of meeting a wide variety of exploration mission objectives, including human exploration of the Martian surface. Incorporating titanium bearings into the Z-series space suit architecture allows us to reduce mass by an estimated 23 lbs per suit system compared to the previously used stainless steel bearing race designs, without compromising suit functionality. There are two obstacles to overcome when using titanium for a bearing race- 1) titanium is flammable when exposed to the oxygen wetted environment inside the space suit and 2) titanium's poor wear properties are often challenging to overcome in tribology applications. In order to evaluate the ignitability of a titanium space suit bearing, a series of tests were conducted at White Sands Test Facility (WSTF) that introduced the bearings to an extreme test profile, with multiple failures imbedded into the test bearings. The testing showed no signs of ignition in the most extreme test cases; however, substantial wear of the bearing races was observed. In order to design a bearing that can last an entire exploration mission (approx. 3 years), design parameters for maximum contact stress need to be identified. To identify these design parameters, bearing test rigs were developed that allow for the quick evaluation of various bearing ball loads, ball diameters, lubricants, and surface treatments. This test data will allow designers to minimize the titanium bearing mass for a specific material and lubricant combination and design around a cycle life requirement for an exploration mission. This paper reviews the current research and testing that has been performed on titanium bearing races to evaluate the use of such materials in an enriched oxygen environment and to optimize the bearing assembly mass and tribological properties to accommodate for the high bearing cycle life for an exploration mission.

Comparative evaluation of the liver in dogs with a splenic mass by using ultrasonography and contrast-enhanced computed tomography

PubMed Central

Irausquin, Roelof A.; Scavelli, Thomas D.; Corti, Lisa; Stefanacci, Joseph D.; DeMarco, Joann; Flood, Shannon; Rohrbach, Barton W.

2008-01-01

Evaluation of dogs with splenic masses to better educate owners as to the extent of the disease is a goal of many research studies. We compared the use of ultrasonography (US) and contrast-enhanced computed tomography (CT) to evaluate the accuracy of detecting hepatic neoplasia in dogs with splenic masses, independently, in series, or in parallel. No significant difference was found between US and CT. If the presence or absence of ascites, as detected with US, was used as a pretest probability of disease in our population, the positive predictive value increased to 94% if the tests were run in series, and the negative predictive value increased to 95% if the tests were run in parallel. The study showed that CT combined with US could be a valuable tool in evaluation of dogs with splenic masses. PMID:18320977

Alternatives to Pyrotechnic Distress Signals; Additional Signal Evaluation

DTIC Science & Technology

2017-06-01

conducted a series of laboratory experiments designed to determine the optimal signal color and temporal pattern for identification against a variety of...practice” trials at approximately 2030 local time and began the actual Test 1 observation trials at approximately 2130. The series of trials finished at...Lewandowski , 860-271-2692, email: M.J.Lewandowski@uscg.mil 16. Abstract (MAXIMUM 200 WORDS) This report is the fourth in a series that details work

Construct-a-Boat. Science by Design Series.

ERIC Educational Resources Information Center

Baroway, William

This book is one of four books in the Science-by-Design Series created by TERC and funded by the National Science Foundation (NSF). It challenges high school students to investigate the physics of boat performance and work with systems and modeling. Through research, design, testing, and evaluation of a model boat, students experience the…

AGARD Flight Test Techniques Series. Volume 12. The Principles of Flight Test Assessment of Flight-Safety-Critical Systems in Helicopters (Les Principes de l’Evaluation, dans le Cadre des Essais en Vol, des Systemes Indispensables a la Securite de Vol des Helicopteres)

DTIC Science & Technology

1994-08-01

AGARD-AG-300 Vol. 12 04 ADVISORY GROUP FOR AEROSPACE RESEARCH & DEVELOPMENT 7 RUE ANCELLE, 92200 NEUILLY-SUR-SEINE, FRANCE AUG 0195 AGARDograph 300...AGARD Flight Test Techniques Series Volume 12 on The Principles of Flight Test Assessment of Flight-Safety-Critical Systems in Helicopters (Les...and Availability on Back Cover AGARD-AG-300 Vol. 12 ADVISORY GROUP FOR AEROSPACE RESEARCH & DEVELOPMENT 7 RUE ANCELLE, 92200 NEUILLY-SUR-SEINE, FRANCE

Advanced Actuation Systems Development. Volume 2

DTIC Science & Technology

1989-08-01

and unloaded performance characteristics of a test specimen produced by General Dynamics Corporation as a feasibility model. The actuation system for...changing the camber of the test specimen is unique and was evaluated with a series of input/output measurements. The testing verified the general ...MAWS General ’rest Procedure........................................6 General Performance Measurements .................................... 10 Test

Mathematics Library of Test Items. Volume One.

ERIC Educational Resources Information Center

Fraser, Graham, Ed.

As one in a series of test item collections developed by the Assessment and Evaluation Unit of the Directorate of Studies, items of value from previous tests are made available to teachers for the construction of pretests or posttests, reference tests for inter-class comparisons and general assignments. The collection was reviewed for content…

Agriculture Library of Test Items.

ERIC Educational Resources Information Center

Sutherland, Duncan, Ed.

As one in a series of test item collections developed by the Assessment and Evaluation Unit of the Directorate of Studies, items of value from past tests are made available to teachers for the construction of unit tests, term examinations or as a basis for class discussion. Each collection is reviewed for content validity and reliability. The test…

Improvements in safety testing of lithium cells

NASA Astrophysics Data System (ADS)

Stinebring, R. C.; Krehl, P.

1985-07-01

A systematic approach was developed for evaluating the basic safety parameters of high power lithium soluble cathode cells. This approach consists of performing a series of tests on each cell model during the design, prototype and production phases. Abusive testing is performed in a facility where maximum protection is given to test personnel.

Improvements in safety testing of lithium cells

NASA Technical Reports Server (NTRS)

Stinebring, R. C.; Krehl, P.

1985-01-01

A systematic approach was developed for evaluating the basic safety parameters of high power lithium soluble cathode cells. This approach consists of performing a series of tests on each cell model during the design, prototype and production phases. Abusive testing is performed in a facility where maximum protection is given to test personnel.

Design and testing of an energy-absorbing crewseat for the F/FB-111 aircraft, volume 1

NASA Technical Reports Server (NTRS)

Shane, S. J.

1985-01-01

A program to determine if the injury potential could be reduced by replacing the existing crewseats with energy absorbing crewseats is explored. An energy-absorbing test seat was designed using much of the existing seat hardware. An extensive dynamic seat test series, designed to duplicate various crew module ground impact conditions, was conducted at a sled test facility. Comparative tests with operational F-111 crewseats were also conducted. After successful dynamic testing of the seat, more testing was conducted with the seats mounted in an F-111 crew module. Both swing tests and vertical drop tests were conducted. The vertical drop tests were used to obtain comparative data between the energy-absorbing and operational seats. Volume 1 describes the energy absorbing test seat and testing conducted, and evaluates the data from both test series.

Maximal oxygen uptake and cardiorespiratory response to maximal 400-m free swimming, running and cycling tests in competitive swimmers.

PubMed

Rodríguez, F A

2000-06-01

This study compared the cardiorespiratory response of trained swimmers to 400-m unimpeded front crawl swimming (SW), treadmill running (TR) and ergometer cycling (EC) maximal exercise tests, and evaluated the validity and specificity of a method to measure maximal aerobic power in swimming. Two series of experiments were conducted. In series A (n=15), comparisons were made between VO2peak and other cardiorespiratory variables in three maximal tests: after 400-m SW, and during incremental TR and EC. In series B, VO2 peak and related variables were measured after SW and during EC (n=33). No significant differences were observed between VO2peak and VE in the three modes of exercise, although SW values tended to be higher. After SW, maximal ventilatory response was characterized by higher tidal volumes (VT) and lower respiratory rates (fR) as compared with TR and EC. The highest heart rate values (fH) were also observed in TR, followed by EC and SW. In series B, no significant differences were observed either in peak VO2 or VE, but fH was also lower in SW. A maximal 400-m unimpeded freestyle SW test yields essentially equal or nonsignificantly higher peak VO2 and VE values than during maximal TR or EC tests in trained swimmers. The specific maximal cardiorespiratory response to the SW test is characterized by higher VT, lower fR, and lower fH. Breath-by-breath measurements during the immediate recovery after a 400-m voluntary maximal swim is proposed as a valid and specific test for directly measuring maximal metabolic parameters and evaluating specific maximal aerobic power in swimming.

Comparative evaluation of concrete bridge deck sealers.

DOT National Transportation Integrated Search

2015-08-01

The main objective of this research was to compare the performance of five bridge deck sealer products using a : synthesis of two testing methods: NCHRP Report 244 Series II tests and standards developed by the Alberta : Ministry of Transportation (B...

An Evaluation of TCITY: The Twin City Institute for Talented Youth. Report #1 in Evaluation Report Series.

ERIC Educational Resources Information Center

Stake, Robert E.; Gjerde, Craig

This evaluation of the Twin City Institute for Talented Youth, a summer program for gifted students in grades 9 through 12, consists of two parts: a description of the program; and the evaluators' assessments, including advocate and adversary reports. Achievement tests were not used for evaluation. Evaluative comments follow each segment of the…

Test Procedures for Characterizing, Evaluating, and Managing Separator Materials used in Secondary Alkaline Batteries

NASA Technical Reports Server (NTRS)

Guasp, Edwin; Manzo, Michelle A.

1997-01-01

Secondary alkaline batteries, such as nickel-cadmium and silver-zinc, are commonly used for aerospace applications. The uniform evaluation and comparison of separator properties for these systems is dependent upon the measurement techniques. This manual presents a series of standard test procedures that can be used to evaluate, compare, and select separator materials for use in alkaline batteries. Detailed test procedures evaluating the following characteristics are included in this manual: physical measurements of thickness and area weight, dimensional stability measurements, electrolyte retention, resistivity, permeability as measured via bubble pressure, surface evaluation via SEM, chemical stability, and tensile strength.

Creating an Advertising Campaign: An Evaluation Report for the Occupational Exploration Programs.

ERIC Educational Resources Information Center

Altschuld, James W.; And Others

The evaluation report is one of seven produced for the Occupational Exploration Program (OEP), a series of simulated occupational experiences designed for junior high school students. Describing the pilot testing of the simulation dealing with advertising, the report contains sections describing the simulation context, evaluation procedures,…

Planning Educational Programs: An Evaluation Report for the Occupational Exploration Program.

ERIC Educational Resources Information Center

Altschuld, James W.; Pritz, Sandra

The evaluation report is one of seven produced for the Occupational Exploration Program (OEP), a series of simulated occupational experiences designed for junior high school students. Describing the pilot testing of the simulation dealing with education, the report contains sections describing the simulation context, evaluation procedures,…

Test and evaluation of load converter topologies used in the Space Station Freedom Power Management and distribution DC test bed

NASA Technical Reports Server (NTRS)

Lebron, Ramon C.; Oliver, Angela C.; Bodi, Robert F.

1991-01-01

Power components hardware in support of the Space Station Freedom dc Electrical Power System were tested. One type of breadboard hardware tested is the dc Load Converter Unit, which constitutes the power interface between the electric power system and the actual load. These units are dc to dc converters that provide the final system regulation before power is delivered to the load. Three load converters were tested: a series resonant converter, a series inductor switchmode converter, and a switching full-bridge forward converter. The topology, operation principles, and tests results are described, in general. A comparative analysis of the three units is given with respect to efficiency, regulation, short circuit behavior (protection), and transient characteristics.

Evaluation of standing noise barriers.

DOT National Transportation Integrated Search

1978-01-01

A series of tests have been carried out at six sites for the evaluation of noise barriers to determine their relative effectiveness. Two barriers were metal, two were wooden, and one was concrete. One site, used for reference, had no barrier. The eff...

Field evaluation of descent advisor trajectory prediction accuracy

DOT National Transportation Integrated Search

1996-07-01

The Descent Advisor (DA) automation tool has undergone a series of field tests : at the Denver Air Route Traffic Control Center to study the feasibility of : DA-based clearances and procedures. The latest evaluation, conducted in the : fall of 1995, ...

Multifunction LIDAR sensors for noncontact, speed, and complex rail dynamics.

DOT National Transportation Integrated Search

2014-07-01

The results of an extensive series of tests are presented to evaluate the viability and applicability of LIDAR systems for measuring : track speed, distance, and curvature in revenue service. The tests indicate that a LIDAR system can successfully pr...

Modeling seasonal variation of hip fracture in Montreal, Canada.

PubMed

Modarres, Reza; Ouarda, Taha B M J; Vanasse, Alain; Orzanco, Maria Gabriela; Gosselin, Pierre

2012-04-01

The investigation of the association of the climate variables with hip fracture incidences is important in social health issues. This study examined and modeled the seasonal variation of monthly population based hip fracture rate (HFr) time series. The seasonal ARIMA time series modeling approach is used to model monthly HFr incidences time series of female and male patients of the ages 40-74 and 75+ of Montreal, Québec province, Canada, in the period of 1993-2004. The correlation coefficients between meteorological variables such as temperature, snow depth, rainfall depth and day length and HFr are significant. The nonparametric Mann-Kendall test for trend assessment and the nonparametric Levene's test and Wilcoxon's test for checking the difference of HFr before and after change point are also used. The seasonality in HFr indicated sharp difference between winter and summer time. The trend assessment showed decreasing trends in HFr of female and male groups. The nonparametric test also indicated a significant change of the mean HFr. A seasonal ARIMA model was applied for HFr time series without trend and a time trend ARIMA model (TT-ARIMA) was developed and fitted to HFr time series with a significant trend. The multi criteria evaluation showed the adequacy of SARIMA and TT-ARIMA models for modeling seasonal hip fracture time series with and without significant trend. In the time series analysis of HFr of the Montreal region, the effects of the seasonal variation of climate variables on hip fracture are clear. The Seasonal ARIMA model is useful for modeling HFr time series without trend. However, for time series with significant trend, the TT-ARIMA model should be applied for modeling HFr time series. Copyright © 2011 Elsevier Inc. All rights reserved.

Landscape Maintenance and Establishment. A Student Handbook. Teacher Education Series, Volume 9 Number 2S.

ERIC Educational Resources Information Center

Pennsylvania State Univ., University Park. Pennsylvania Agricultural Experiment Station.

This student handbook is one of a series of instructional aids prepared and edited by the Department of Agricultural Education at the Pennsylvania State University. Its organization and content were field tested, evaluated, and improved by teachers attending summer institutes in ornamental horticulture in 1966 and 1967. The content includes…

Acoustic and Thermal Testing of an Integrated Multilayer Insulation and Broad Area Cooling Shield System

NASA Technical Reports Server (NTRS)

Wood, Jessica J.; Foster, Lee W.

2013-01-01

A Multilayer Insulation (MLI) and Broad Area Cooling (BAC) shield thermal control system shows promise for long-duration storage of cryogenic propellant. The NASA Cryogenic Propellant Storage and Transfer (CPST) project is investigating the thermal and structural performance of this tank-applied integrated system. The MLI/BAC Shield Acoustic and Thermal Test was performed to evaluate the MLI/BAC shield's structural performance by subjecting it to worst-case launch acoustic loads. Identical thermal tests using Liquid Nitrogen (LN2) were performed before and after the acoustic test. The data from these tests was compared to determine if any degradation occurred in the thermal performance of the system as a result of exposure to the acoustic loads. The thermal test series consisted of two primary components: a passive boil-off test to evaluate the MLI performance and an active cooling test to evaluate the integrated MLI/BAC shield system with chilled vapor circulating through the BAC shield tubes. The acoustic test used loads closely matching the worst-case envelope of all launch vehicles currently under consideration for CPST. Acoustic test results yielded reasonable responses for the given load. The thermal test matrix was completed prior to the acoustic test and successfully repeated after the acoustic test. Data was compared and yielded near identical results, indicating that the MLI/BAC shield configuration tested in this series is an option for structurally implementing this thermal control system concept.

Geography Library of Test Items. Volume Four.

ERIC Educational Resources Information Center

Kouimanos, John, Ed.

As one in a series of test item collections developed by the Assessment and Evaluation Unit of the Directorate of Studies, items of value from past tests are made available to teachers for the construction of unit tests, term examinations or as a basis for class discussion. Each collection was reviewed for content validity and reliability. The…

Home Science Library of Test Items. Volume One.

ERIC Educational Resources Information Center

Smith, Jan, Ed.

As one in a series of test item collections developed by the Assessment and Evaluation Unit of the Directorate of Studies, items of value from past tests are made available to teachers for the construction of unit tests, term examinations or as a basis for class discussion. Each collection is reviewed for content validity and reliability. The test…

Languages Library of Test Items. Volume Two: German, Latin.

ERIC Educational Resources Information Center

Campbell, Thomas; And Others

As one in a series of test item collections developed by the Assessment and Evaluation Unit of the Directorate of Studies, items of value from past tests are made available to teachers for the construction of unit tests, term examinations or as a basis for class discussion. Each collection was reviewed for content validity and reliability. The…

Languages Library of Test Items. Volume One: French, Indonesian.

ERIC Educational Resources Information Center

Campbell, Thomas; And Others

As one in a series of test item collections developed by the Assessment and Evaluation Unit of the Directorate of Studies, items of value from past tests are made available to teachers for the construction of unit tests, term examinations or as a basis for class discussion. Each collection was reviewed for content validity and reliability. The…

Geography Library of Test Items. Volume Three.

ERIC Educational Resources Information Center

Kouimanos, John, Ed.

As one in a series of test item collections developed by the Assessment and Evaluation Unit of the Directorate of Studies, items of value from past tests are made available to teachers for the construction of unit tests, term examinations or as a basis for class discussion. Each collection was reviewed for content validity and reliability. The…

Commerce Library of Test Items. Volume One.

ERIC Educational Resources Information Center

Meeve, Brian, Ed.

As one in a series of test item collections developed by the Assessment and Evaluation Unit of the Directorate of Studies, items of value from past tests are made available to teachers for the construction of unit tests, term examinations or as a basis for class discussion. Each collection was reviewed for content validity and reliability. The…

Geography Library of Test Items. Volume Five.

ERIC Educational Resources Information Center

Kouimanos, John, Ed.

As one in a series of test item collections developed by the Assessment and Evaluation Unit of the Directorate of Studies, items of value from past tests are made available to teachers for the construction of unit tests, term examinations or as a basis for class discussion. Each collection was reviewed for content validity and reliability. The…

Textiles and Design Library of Test Items. Volume I.

ERIC Educational Resources Information Center

Smith, Jan, Ed.

As one in a series of test item collections developed by the Assessment and Evaluation Unit of the Directorate of Studies, items of value from past tests are made available to teachers for the construction of unit tests, term examinations or as a basis for class discussion. Each collection is reviewed for content validity and reliability. The test…

Commerce Library of Test Items. Volume Two.

ERIC Educational Resources Information Center

Meeve, Brian, Ed.

As one in a series of test item collections developed by the Assessment and Evaluation Unit of the Directorate of Studies, items of value from past tests are made available to teachers for the construction of unit tests, term examinations or as a basis for class discussion. Each collection was reviewed for content validity and reliability. The…

Geography Library of Test Items. Volume Six.

ERIC Educational Resources Information Center

Kouimanos, John, Ed.

As one in a series of test item collections developed by the Assessment and Evaluation Unit of the Directorate of Studies, items of value from past tests are made available to teachers for the construction of unit tests, term examinations or as a basis for class discussion. Each collection was reviewed for content validity and reliability. The…

Geography: Library of Test Items. Volume II.

ERIC Educational Resources Information Center

Kouimanos, John, Ed.

As one in a series of test item collections developed by the Assessment and Evaluation Unit of the Directorate of Studies, items of value from past tests are made available to teachers for the construction of unit tests, term examinations or as a basis for class discussion. Each collection was reviewed for content validity and reliability. The…

Geography Library of Test Items. Volume One.

ERIC Educational Resources Information Center

Kouimanos, John, Ed.

As one in a series of test item collections developed by the Assessment and Evaluation Unit of the Directorate of Studies, items of value from past tests are made available to teachers for the construction of unit tests, term examinations or as a basis for class discussion. Each collection was reviewed for content validity and reliability. The…

Investigation of Time Series Representations and Similarity Measures for Structural Damage Pattern Recognition

PubMed Central

Swartz, R. Andrew

2013-01-01

This paper investigates the time series representation methods and similarity measures for sensor data feature extraction and structural damage pattern recognition. Both model-based time series representation and dimensionality reduction methods are studied to compare the effectiveness of feature extraction for damage pattern recognition. The evaluation of feature extraction methods is performed by examining the separation of feature vectors among different damage patterns and the pattern recognition success rate. In addition, the impact of similarity measures on the pattern recognition success rate and the metrics for damage localization are also investigated. The test data used in this study are from the System Identification to Monitor Civil Engineering Structures (SIMCES) Z24 Bridge damage detection tests, a rigorous instrumentation campaign that recorded the dynamic performance of a concrete box-girder bridge under progressively increasing damage scenarios. A number of progressive damage test case datasets and damage test data with different damage modalities are used. The simulation results show that both time series representation methods and similarity measures have significant impact on the pattern recognition success rate. PMID:24191136

INFFTM: Fast evaluation of 3d Fourier series in MATLAB with an application to quantum vortex reconnections

NASA Astrophysics Data System (ADS)

Caliari, Marco; Zuccher, Simone

2017-04-01

Although Fourier series approximation is ubiquitous in computational physics owing to the Fast Fourier Transform (FFT) algorithm, efficient techniques for the fast evaluation of a three-dimensional truncated Fourier series at a set of arbitrary points are quite rare, especially in MATLAB language. Here we employ the Nonequispaced Fast Fourier Transform (NFFT, by J. Keiner, S. Kunis, and D. Potts), a C library designed for this purpose, and provide a Matlab® and GNU Octave interface that makes NFFT easily available to the Numerical Analysis community. We test the effectiveness of our package in the framework of quantum vortex reconnections, where pseudospectral Fourier methods are commonly used and local high resolution is required in the post-processing stage. We show that the efficient evaluation of a truncated Fourier series at arbitrary points provides excellent results at a computational cost much smaller than carrying out a numerical simulation of the problem on a sufficiently fine regular grid that can reproduce comparable details of the reconnecting vortices.

Image degradation in aerial imagery duplicates. [photographic processing of photographic film and reproduction (copying)

NASA Technical Reports Server (NTRS)

Lockwood, H. E.

1975-01-01

A series of Earth Resources Aircraft Program data flights were made over an aerial test range in Arizona for the evaluation of large cameras. Specifically, both medium altitude and high altitude flights were made to test and evaluate a series of color as well as black-and-white films. Image degradation, inherent in duplication processing, was studied. Resolution losses resulting from resolution characteristics of the film types are given. Color duplicates, in general, are shown to be degraded more than black-and-white films because of the limitations imposed by available aerial color duplicating stock. Results indicate that a greater resolution loss may be expected when the original has higher resolution. Photographs of the duplications are shown.

Design and evaluation of an energy-absorbing, reusable roadside/median barrier.

DOT National Transportation Integrated Search

2015-07-01

Further design and evaluation was conducted on an energy-absorbing, restorable and reusable roadside/median barrier, : designated the RESTORE barrier. A series of dynamic component tests were conducted on 11-in. (295-mm) tall x 10-in. : (254-mm) w...

PILOT-SCALE INCINERATION TEST BURN OF TCDD-CONTAMINATED TRICHLOROPHENOL PRODUCTION WASTE

EPA Science Inventory

A series of three tests directed at evaluating the incinerability of the toluene stillbottoms waste from trichlorophenol production previously generated by the Vertac Chemical Company were performed in the Combustion Research Facility (CRF) rotary kiln incineration system. This w...

Pediatric Baseline Patch Test Series: Initial Findings of the Pediatric Contact Dermatitis Workgroup.

PubMed

Yu, JiaDe; Atwater, Amber Reck; Brod, Bruce; Chen, Jennifer K; Chisolm, Sarah S; Cohen, David E; de la Feld, Salma; Gaspari, Anthony A; Martin, Kari Lyn; Montanez-Wiscovich, Marjorie; Sheehan, Michael; Silverberg, Nanette; Lugo-Somolinos, Aida; Thakur, Binod K; Watsky, Kalman; Jacob, Sharon E

2018-06-21

Allergic contact dermatitis is a challenging diagnostic problem in children. Although epicutaneous patch testing is the diagnostic standard for confirmation of contact sensitization, it is less used in children by dermatologists treating children, pediatric dermatologists, and pediatricians, when compared with adult practitioners. The aim of the study was to create and evaluate standardization of a pediatric patch test series for children older than 6 years. We surveyed dermatologists and allergists conducting epicutaneous patch testing in children attending the 2017 American Contact Dermatitis Society meeting held in Washington, DC. This was followed by discussion of collected data and consensus review by a pediatric contact dermatitis working group at the conference. A baseline pediatric patch test panel was established through working group consensus.

Sleep-inducing N-alkyl-5-[m-(trifluoromethyl)phenyl]-5-hydroxy-2-pyrrolidinones and N-alkyl-3-(trifluoromethyl)cinnamamides.

PubMed

Houlihan, W J; Gogerty, J H; Ryan, E A; Schmitt, G

1985-01-01

A series of N-alkyl-3-[m-(trifluoromethyl)phenyl]-5-hydroxy-2-pyrrolidinones and N-alkyl-3-(trifluoromethyl)-cinnamamides were prepared and screened in a series of tests designed to detect potential sleep inducers. The more active members of the series were evaluated for their ability to induce sleep in Cebus monkeys. The most active compound, N-methyl-5-[m-(trifluoromethyl)phenyl]-5-hydroxy-2-pyrrolidinone, was equal to methaqualone.

Aligning English Language Testing with Curriculum

ERIC Educational Resources Information Center

Palacio, Marcela; Gaviria, Sandra; Brown, James Dean

2016-01-01

Frustrations with traditional testing led a group of teachers at the English for adults program at Universidad EAFIT (Colombia) to design tests aligned with the institutional teaching philosophy and classroom practices. This article reports on a study of an item-by-item evaluation of a series of English exams for validity and reliability in an…

Science Library of Test Items. Volume Four: Practical Testing Guide.

ERIC Educational Resources Information Center

New South Wales Dept. of Education, Sydney (Australia).

As one in a series of test items collections developed by the Assessment and Evaluation Unit of the Directorate of Studies, the guide gives a wide range of questions and activities for the manipulation of scientific equipment to allow assessment of students' practical laboratory skills. Instructions are given to make norm-referenced or…

The importance of assessing for validity of symptom report and performance in attention deficit/hyperactivity disorder (ADHD): Introduction to the special section on noncredible presentation in ADHD.

PubMed

Suhr, Julie A; Berry, David T R

2017-12-01

Invalid self-report and invalid performance occur with high base rates in attention deficit/hyperactivity disorder (ADHD; Harrison, 2006; Musso & Gouvier, 2014). Although much research has focused on the development and validation of symptom validity tests (SVTs) and performance validity tests (PVTs) for psychiatric and neurological presentations, less attention has been given to the use of SVTs and PVTs in ADHD evaluation. This introduction to the special section describes a series of studies examining the use of SVTs and PVTs in adult ADHD evaluation. We present the series of studies in the context of prior research on noncredible presentation and call for future research using improved research methods and with a focus on assessment issues specific to ADHD evaluation. (PsycINFO Database Record (c) 2017 APA, all rights reserved).

Test and evaluation of load converter topologies used in the Space Station Freedom power management and distribution dc test bed

NASA Technical Reports Server (NTRS)

Lebron, Ramon C.; Oliver, Angela C.; Bodi, Robert F.

1991-01-01

Power components hardware in support of the Space Station freedom dc Electric Power System were tested. One type of breadboard hardware tested is the dc Load Converter Unit, which constitutes the power interface between the electric power system and the actual load. These units are dc to dc converters that provide the final system regulation before power is delivered to the load. Three load converters were tested: a series resonant converter, a series inductor switch-mode converter, and a switching full-bridge forward converter. The topology, operation principles, and test results are described, in general. A comparative analysis of the three units is given with respect to efficiency, regulation, short circuit behavior (protection), and transient characteristics.

Evolving Maturation of the Series-Bosch System

NASA Technical Reports Server (NTRS)

Stanley, Christine; Abney, Morgan B.; Barnett, Bill

2017-01-01

Human exploration missions to Mars and other destinations beyond low Earth orbit require highly robust, reliable, and maintainable life support systems that maximize recycling of water and oxygen. In order to meet this requirement, NASA has continued the development of a Series-Bosch System, a two stage reactor process that reduces carbon dioxide (CO2) with hydrogen (H2) to produce water and solid carbon. Theoretically, the Bosch process can recover 100% of the oxygen (O2) from CO2 in the form of water, making it an attractive option for long duration missions. The Series Bosch system includes a reverse water gas shift (RWGS) reactor, a carbon formation reactor (CFR), an H2 extraction membrane, and a CO2 extraction membrane. In 2016, the results of integrated testing of the Series Bosch system showed great promise and resulted in design modifications to the CFR to further improve performance. This year, integrated testing was conducted with the modified reactor to evaluate its performance and compare it with the performance of the previous configuration. Additionally, a CFR with the capability to load new catalyst and remove spent catalyst in-situ was built. Flow demonstrations were performed to evaluate both the catalyst loading and removal process and the hardware performance. The results of the integrated testing with the modified CFR as well as the flow demonstrations are discussed in this paper.

Hyperion 5113/A Infrasound Sensor Evaluation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Merchant, Bion John

2015-09-01

Sandia National Laboratories has tested and evaluated an infrasound sensor, the 5113/A manufactured by Hyperion. These infrasound sensors measure pressure output by a methodology developed by the University of Mississippi. The purpose of the infrasound sensor evaluation was to determine a measured sensitivity, transfer function, power, self-noise, and dynamic range. The 5113/A infrasound sensor is a new revision of the 5000 series intended to meet the infrasound application requirements for use in the International Monitoring System (IMS) of the Comprehensive Nuclear-Test-Ban Treaty Organization (CTBTO).

The Validity and Precision of the Comparative Interrupted Time-Series Design: Three Within-Study Comparisons

ERIC Educational Resources Information Center

St. Clair, Travis; Hallberg, Kelly; Cook, Thomas D.

2016-01-01

We explore the conditions under which short, comparative interrupted time-series (CITS) designs represent valid alternatives to randomized experiments in educational evaluations. To do so, we conduct three within-study comparisons, each of which uses a unique data set to test the validity of the CITS design by comparing its causal estimates to…

NEUROBEHAVIORAL DATA INTERPRETATION IN NEUROTOXICITY STUDIES: FOB, MOTOR ACTIVITY AND FUNCTION

EPA Science Inventory

Neurobehavioral evaluations are emerging as a key component in neurotoxicity testing. The tests most often used for screening are the functional observational battery (FOB) and motor activity. The FOB is a series of non-invasive observational and manipulative measures which ass...

LNG vapor barrier and obstacle evaluation: Wind-tunnel simulation of 1987 Falcon Spill Series. Final report, July 1987-February 1991

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shin, S.H.; Meroney, R.N.; Neff, D.E.

1991-03-01

Measurements of the behavior of simulated liquefied natural gas clouds dispersing over small-scale model placed in environmental wind tunnels permits evaluations of the fluid physics of dense cloud movement and dispersion in a controlled environment. A large data base on the interaction of simulated LNG plumes with the Falcon test configuration of vapor barrier fences and vortex generators was obtained. The purpose of the reported test program is to provide post-field-spill wind tunnel experiments to augment the LNG Vapor Fence Field Program data obtained during the Falcon Test Series in 1987. The goal of the program is to determine themore » probable response of a dense LNG Vapor cloud to vortex inducer obstacles and fences, examine the sensitivity of results to various scaling arguments which might augment limit, or extend the value of the field and wind-tunnel tests, and identify important details of the spill behavior which were not predicted during the pretest planning phase.« less

Science Library of Test Items. Volume Nineteen. A Collection of Multiple Choice Test Items Relating Mainly to Geology.

ERIC Educational Resources Information Center

New South Wales Dept. of Education, Sydney (Australia).

As one in a series of test item collections developed by the Assessment and Evaluation Unit of the Directorate of Studies, items are made available to teachers for the construction of unit tests or term examinations or as a basis for class discussion. Each collection was reviewed for content validity and reliability. The test items meet syllabus…

Science Library of Test Items. Volume Seventeen. A Collection of Multiple Choice Test Items Relating Mainly to Biology.

ERIC Educational Resources Information Center

New South Wales Dept. of Education, Sydney (Australia).

As one in a series of test item collections developed by the Assessment and Evaluation Unit of the Directorate of Studies, items are made available to teachers for the construction of unit tests or term examinations or as a basis for class discussion. Each collection was reviewed for content validity and reliability. The test items meet syllabus…

Science Library of Test Items. Volume Eighteen. A Collection of Multiple Choice Test Items Relating Mainly to Chemistry.

ERIC Educational Resources Information Center

New South Wales Dept. of Education, Sydney (Australia).

As one in a series of test item collections developed by the Assessment and Evaluation Unit of the Directorate of Studies, items are made available to teachers for the construction of unit tests or term examinations or as a basis for class discussion. Each collection was reviewed for content validity and reliability. The test items meet syllabus…

Ethylhexylglycerin: a low-risk, but highly relevant, sensitizer in 'hypo-allergenic' cosmetics.

PubMed

Aerts, Olivier; Verhulst, Lien; Goossens, An

2016-05-01

Ethylhexylglycerin is a relatively new cosmetic ingredient that is used for its surfactant, emollient, skin-conditioning and antimicrobial properties. Since 2002, it has been occasionally reported as a contact allergen. To report on 13 patients who presented with allergic contact dermatitis caused by ethylhexylglycerin, evaluated at two Belgian university patch test clinics during the period 1990-2015. The patients were patch tested with the European baseline series, a cosmetic series, and - if indicated - additional series. Both the cosmetic products used and their single ingredients were patch tested. All but one of the ethylhexylglycerin-allergic patients were female, with a median age of 43 years (range: 29-81 years), most often suffering from dermatitis on the face, and sometimes on the hands and/or axillae. As the culprit products, leave-on cosmetics were identified, including a high number of proclaimed 'hypo-allergenic' and 'preservative-free' facial creams, sun protection creams, and deodorants. Ethylhexylglycerin is a rare, but highly relevant, cosmetic sensitizer, even in those products advertised to be safe for consumers. Targeted patch testing with ethylhexylglycerin 5% pet. is very useful, and routine patch testing in a cosmetic series may be considered. Higher test concentrations might be indicated in selected cases. © 2016 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

LANDSAT Range Resource Information System. [a user evaluation of green forage and rainfall accumulation maps

NASA Technical Reports Server (NTRS)

Boyd, W. E.; Harlan, J. C.

1981-01-01

A series of test products were developed from LANDSAT data sets for North Central Texas that paralleled the needs of ranchers, technical personnel, and the media. The products and evaluation questionnaires were mailed to approximately 150 ranchers who had reported an interest in evaluating the information systems. In addition to the rancher group, fourteen media people and a thirty-three member group in the agri business/technical community was also chosen to receive test products. The group responses are analyzed. Examples of the test products and associated questionnaires are included.

Oral Assessment Kit, Levels II & III. Draft.

ERIC Educational Resources Information Center

Agrelo-Gonzalez, Maria; And Others

The assessment packet includes a series of oral tests to help develop speaking as an integral part of second language instruction at levels II and III. It contains: 8 mini-tests for use at level II; 9 mini-tests for use at level III; a rating scale and score sheet masters for evaluating performance on these tests; and a collection of suggested…

Fractured reservoir characterization through injection, falloff, and flowback tests

DOE Office of Scientific and Technical Information (OSTI.GOV)

Peng, C.P.; Singh, P.K.; Halvorsen, H.

1992-09-01

This paper presents the development of a multiphase pressure-transient-analysis technique for naturally fractured reservoirs and the analysis of a series of field tests performed to evaluate the water injection potential and the reservoir characteristics of a naturally fractured reservoir. These included step-rate, water-injectivity, pressure-falloff, and flowback tests. Through these tests, a description of the reservoir was obtained.

SPE5 Sub-Scale Test Series Summary Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vandersall, Kevin S.; Reeves, Robert V.; DeHaven, Martin R.

2016-01-14

A series of 2 SPE5 sub-scale tests were performed to experimentally confirm that a booster system designed and evaluated in prior tests would properly initiate the PBXN-110 case charge fill. To conduct the experiments, a canister was designed to contain the nominally 50 mm diameter booster tube with an outer fill of approximately 150 mm diameter by 150 mm in length. The canisters were filled with PBXN-110 at NAWS-China Lake and shipped back to LLNL for testing in the High Explosives Applications Facility (HEAF). Piezoelectric crystal pins were placed on the outside of the booster tube before filling, and amore » series of piezoelectric crystal pins along with Photonic Doppler Velocimetry (PDV) probes were placed on the outer surface of the canister to measure the relative timing and magnitude of the detonation. The 2 piezoelectric crystal pins integral to the booster design were also utilized along with a series of either piezoelectric crystal pins or piezoelectric polymer pads on the top of the canister or outside case that utilized direct contact, gaps, or different thicknesses of RTV cushions to obtain time of arrival data to evaluate the response in preparation for the large-scale SPE5 test. To further quantify the margin of the booster operation, the 1st test (SPE5SS1) was functioned with both detonators and the 2nd test (SPE5SS2) was functioned with only 1 detonator. A full detonation of the material was observed in both experiments as observed by the pin timing and PDV signals. The piezoelectric pads were found to provide a greater measured signal magnitude during the testing with an RTV layer present, and the improved response is due to the larger measurement surface area of the pad. This report will detail the experiment design, canister assembly for filling, final assembly, experiment firing, presentation of the diagnostic results, and a discussion of the results.« less

NHTSA's heavy duty vehicle brake research program report number 11 : evaluation of stopping performance of trailer antilock brake systems

DOT National Transportation Integrated Search

1997-04-01

In order to better understand the functioning of antilock brake systems on pneumatically braked trailers, a series of tests were conducted to evaluate different ABS control strategies, performance variations among systems supplied by different manufa...

EVALUATION OF DIFFERENT METHODS FOR THE EXTRACTION OF DNA FROM FUNGAL CONIDIA BY QUANTITATIVE COMPETITIVE PCR ANALYSIS

EPA Science Inventory

Five different DNA extraction methods were evaluated for their effectiveness in recovering PCR templates from the conidia of a series of fungal species often encountered in indoor air. The test organisms were Aspergillus versicolor, Penicillium chrysogenum, Stachybotrys chartaru...

The Historical Development of Evaluation Use

ERIC Educational Resources Information Center

Alkin, Marvin C.; King, Jean A.

2016-01-01

The first article in this series traces the initial development of the concept of evaluation use. As a field, evaluation has always paid attention to the potential for use, both in decision-making and in changing people's thinking. The broad history of the field as we know it today stemmed from two streams: one focused on tests and measurement,…

A Procedure for the Analysis of Time-Series Designs

ERIC Educational Resources Information Center

Algina, James; Swaminathan, Hariharan

1977-01-01

One of the most frequently encountered problems in educational research and evaluation is that of evaluating the effect of a treatment in settings over which the researcher or evaluator has little control. A strong plea is made for use of quasi-experimental designs in these situations and this research provides a method of testing the hypothesis…

Investigating the use of small-diameter softwood as guardrail posts (dynamic test results)

Treesearch

Jason A. Hascall; John D. Reid; Ronald K. Faller; Dean L. Sicking; David E. Kretschmann

2007-01-01

A modified version of the Midwest Guardrail System (MGS), utilizing small-diameter round wood posts, was developed, tested, and evaluated. Three systems were developed using different species of timber, Douglas Fir, Ponderosa Pine, and Southern Yellow Pine. A combination of Barrier VII computer simulation modeling and several series of cantilever bogie tests, conducted...

A Model of International Communication Media Appraisal: Phase IV, Generalizing the Model to Film.

ERIC Educational Resources Information Center

Johnson, J. David

A study tested a causal model of international communication media appraisal using audience evaluations of tests of two films conducted in the Philippines. It was the fourth in a series of tests of the model in both developed and developing countries. In general the model posited determinative relationships between three exogenous variables…

Criterion Referenced Inventory. Grade 7 Skill Clusters, Objectives, and Illustrations.

ERIC Educational Resources Information Center

Montgomery County Public Schools, Rockville, MD.

Part of a series of competency-based test materials for grades six through ten, this test booklet for seventh graders contains multiple-choice questions designed to aid in the evaluation of the pupils' library skills. Accompanied by a separate booklet of illustrations which are to be used in conjunction with the questions, the test covers the…

Modular Cognitive Behavioral Therapy for Youth Anxiety Disorders: A Partial Effectiveness Test in Schools

ERIC Educational Resources Information Center

Chiu, Angela Wai Mon

2010-01-01

The current study used a programmatic dissemination model as a guiding framework for testing an evidence-supported treatment (EST) for child anxiety disorders in the school setting. The main goal of the project was to conduct the first of a planned series of partial-effectiveness tests (group-design randomized controlled trials) evaluating the…

Charge Efficiency Tests of Lead/Acid Batteries

NASA Technical Reports Server (NTRS)

Rowlette, J. J.

1984-01-01

Current, voltage, and gas evolution measured during charge/discharge cycles. Series of standarized tests for evaluating charging efficiency of lead/acid storage batteries described in report. Purpose of tests to provide information for design of battery charger that allows maximum recharge efficiency for electric-vehicle batteries consistent with other operating parameters, such as range, water loss, and cycle life.

Test Anxiety: Theory, Assessment, and Treatment. The Series in Clinical and Community Psychology.

ERIC Educational Resources Information Center

Spielberger, Charles D., Ed.; Vagg, Peter R., Ed.

It is not surprising that a broad array of treatment programs have been developed to reduce test anxiety, since the consequences can be serious. The contributions in this volume review and evaluate the theory of test anxiety, its measurement, its manifestations, and possible treatments and their outcomes. The following chapters are included: (1)…

Retrofit and acceptance test of 30-cm ion thrusters

NASA Technical Reports Server (NTRS)

Poeschel, R. L.

1981-01-01

Six 30 cm mercury thrusters were modified to the J-series design and evaluated using standardized test procedures. The thruster performance meets the design objectives (lifetime objective requires verification), and documentation (drawings, etc.) for the design is completed and upgraded. The retrofit modifications are described and the test data for the modifications are presented and discussed.

Detection of statistical asymmetries in non-stationary sign time series: Analysis of foreign exchange data

PubMed Central

Takayasu, Hideki; Takayasu, Misako

2017-01-01

We extend the concept of statistical symmetry as the invariance of a probability distribution under transformation to analyze binary sign time series data of price difference from the foreign exchange market. We model segments of the sign time series as Markov sequences and apply a local hypothesis test to evaluate the symmetries of independence and time reversion in different periods of the market. For the test, we derive the probability of a binary Markov process to generate a given set of number of symbol pairs. Using such analysis, we could not only segment the time series according the different behaviors but also characterize the segments in terms of statistical symmetries. As a particular result, we find that the foreign exchange market is essentially time reversible but this symmetry is broken when there is a strong external influence. PMID:28542208

Ecological Momentary Assessments and Automated Time Series Analysis to Promote Tailored Health Care: A Proof-of-Principle Study.

PubMed

van der Krieke, Lian; Emerencia, Ando C; Bos, Elisabeth H; Rosmalen, Judith Gm; Riese, Harriëtte; Aiello, Marco; Sytema, Sjoerd; de Jonge, Peter

2015-08-07

Health promotion can be tailored by combining ecological momentary assessments (EMA) with time series analysis. This combined method allows for studying the temporal order of dynamic relationships among variables, which may provide concrete indications for intervention. However, application of this method in health care practice is hampered because analyses are conducted manually and advanced statistical expertise is required. This study aims to show how this limitation can be overcome by introducing automated vector autoregressive modeling (VAR) of EMA data and to evaluate its feasibility through comparisons with results of previously published manual analyses. We developed a Web-based open source application, called AutoVAR, which automates time series analyses of EMA data and provides output that is intended to be interpretable by nonexperts. The statistical technique we used was VAR. AutoVAR tests and evaluates all possible VAR models within a given combinatorial search space and summarizes their results, thereby replacing the researcher's tasks of conducting the analysis, making an informed selection of models, and choosing the best model. We compared the output of AutoVAR to the output of a previously published manual analysis (n=4). An illustrative example consisting of 4 analyses was provided. Compared to the manual output, the AutoVAR output presents similar model characteristics and statistical results in terms of the Akaike information criterion, the Bayesian information criterion, and the test statistic of the Granger causality test. Results suggest that automated analysis and interpretation of times series is feasible. Compared to a manual procedure, the automated procedure is more robust and can save days of time. These findings may pave the way for using time series analysis for health promotion on a larger scale. AutoVAR was evaluated using the results of a previously conducted manual analysis. Analysis of additional datasets is needed in order to validate and refine the application for general use.

Ecological Momentary Assessments and Automated Time Series Analysis to Promote Tailored Health Care: A Proof-of-Principle Study

PubMed Central

Emerencia, Ando C; Bos, Elisabeth H; Rosmalen, Judith GM; Riese, Harriëtte; Aiello, Marco; Sytema, Sjoerd; de Jonge, Peter

2015-01-01

Background Health promotion can be tailored by combining ecological momentary assessments (EMA) with time series analysis. This combined method allows for studying the temporal order of dynamic relationships among variables, which may provide concrete indications for intervention. However, application of this method in health care practice is hampered because analyses are conducted manually and advanced statistical expertise is required. Objective This study aims to show how this limitation can be overcome by introducing automated vector autoregressive modeling (VAR) of EMA data and to evaluate its feasibility through comparisons with results of previously published manual analyses. Methods We developed a Web-based open source application, called AutoVAR, which automates time series analyses of EMA data and provides output that is intended to be interpretable by nonexperts. The statistical technique we used was VAR. AutoVAR tests and evaluates all possible VAR models within a given combinatorial search space and summarizes their results, thereby replacing the researcher’s tasks of conducting the analysis, making an informed selection of models, and choosing the best model. We compared the output of AutoVAR to the output of a previously published manual analysis (n=4). Results An illustrative example consisting of 4 analyses was provided. Compared to the manual output, the AutoVAR output presents similar model characteristics and statistical results in terms of the Akaike information criterion, the Bayesian information criterion, and the test statistic of the Granger causality test. Conclusions Results suggest that automated analysis and interpretation of times series is feasible. Compared to a manual procedure, the automated procedure is more robust and can save days of time. These findings may pave the way for using time series analysis for health promotion on a larger scale. AutoVAR was evaluated using the results of a previously conducted manual analysis. Analysis of additional datasets is needed in order to validate and refine the application for general use. PMID:26254160

Design and evaluation of a 3 million DN series-hybrid thrust bearing. [stability tests and fatigue tests

NASA Technical Reports Server (NTRS)

Scibbe, H. W.; Winn, L. W.; Eusepi, M.

1976-01-01

The bearing, consisting of a 150-mm ball bearing and a centrifugally actuated, conical, fluid-film bearing, was fatigue tested. Test conditions were representative of a mainshaft ball bearing in a gas turbine engine operating at maximum thrust load to simulate aircraft takeoff conditions. Tests were conducted up to 16000 rpm and at this speed an axial load of 15568 newtons (3500 lb) was safely supported by the hybrid bearing system. Through the series-hybrid bearing principle, the effective ball bearing speed was reduced to approximately one-half of the shaft speed. It was concluded that a speed reduction of this magnitude results in a ten-fold increase in the ball bearing fatigue life. A successful evaluation of fluid-film bearing lubricant supply failure was performed repeatedly at an operating speed of 10,000 rpm. A complete and smooth changeover to full-scale ball bearing operation was effected when the oil supply to the fluid-film bearing was cut off. Reactivation of the fluid-film oil supply system resulted in a flawless return to the original mode of hybrid operation.

Immediate versus sustained effects: interrupted time series analysis of a tailored intervention.

PubMed

Hanbury, Andria; Farley, Katherine; Thompson, Carl; Wilson, Paul M; Chambers, Duncan; Holmes, Heather

2013-11-05

Detailed intervention descriptions and robust evaluations that test intervention impact--and explore reasons for impact--are an essential part of progressing implementation science. Time series designs enable the impact and sustainability of intervention effects to be tested. When combined with time series designs, qualitative methods can provide insight into intervention effectiveness and help identify areas for improvement for future interventions. This paper describes the development, delivery, and evaluation of a tailored intervention designed to increase primary health care professionals' adoption of a national recommendation that women with mild to moderate postnatal depression (PND) are referred for psychological therapy as a first stage treatment. Three factors influencing referral for psychological treatment were targeted using three related intervention components: a tailored educational meeting, a tailored educational leaflet, and changes to an electronic system data template used by health professionals during consultations for PND. Evaluation comprised time series analysis of monthly audit data on percentage referral rates and monthly first prescription rates for anti-depressants. Interviews were conducted with a sample of health professionals to explore their perceptions of the intervention components and to identify possible factors influencing intervention effectiveness. The intervention was associated with a significant, immediate, positive effect upon percentage referral rates for psychological treatments. This effect was not sustained over the ten month follow-on period. Monthly rates of anti-depressant prescriptions remained consistently high after the intervention. Qualitative interview findings suggest key messages received from the intervention concerned what appropriate antidepressant prescribing is, suggesting this to underlie the lack of impact upon prescribing rates. However, an understanding that psychological treatment can have long-term benefits was also cited. Barriers to referral identified before intervention were cited again after the intervention, suggesting the intervention had not successfully tackled the barriers targeted. A time series design allowed the initial and sustained impact of our intervention to be tested. Combined with qualitative interviews, this provided insight into intervention effectiveness. Future research should test factors influencing intervention sustainability, and promote adoption of the targeted behavior and dis-adoption of competing behaviors where appropriate.

Immediate versus sustained effects: interrupted time series analysis of a tailored intervention

PubMed Central

2013-01-01

Background Detailed intervention descriptions and robust evaluations that test intervention impact—and explore reasons for impact—are an essential part of progressing implementation science. Time series designs enable the impact and sustainability of intervention effects to be tested. When combined with time series designs, qualitative methods can provide insight into intervention effectiveness and help identify areas for improvement for future interventions. This paper describes the development, delivery, and evaluation of a tailored intervention designed to increase primary health care professionals’ adoption of a national recommendation that women with mild to moderate postnatal depression (PND) are referred for psychological therapy as a first stage treatment. Methods Three factors influencing referral for psychological treatment were targeted using three related intervention components: a tailored educational meeting, a tailored educational leaflet, and changes to an electronic system data template used by health professionals during consultations for PND. Evaluation comprised time series analysis of monthly audit data on percentage referral rates and monthly first prescription rates for anti-depressants. Interviews were conducted with a sample of health professionals to explore their perceptions of the intervention components and to identify possible factors influencing intervention effectiveness. Results The intervention was associated with a significant, immediate, positive effect upon percentage referral rates for psychological treatments. This effect was not sustained over the ten month follow-on period. Monthly rates of anti-depressant prescriptions remained consistently high after the intervention. Qualitative interview findings suggest key messages received from the intervention concerned what appropriate antidepressant prescribing is, suggesting this to underlie the lack of impact upon prescribing rates. However, an understanding that psychological treatment can have long-term benefits was also cited. Barriers to referral identified before intervention were cited again after the intervention, suggesting the intervention had not successfully tackled the barriers targeted. Conclusion A time series design allowed the initial and sustained impact of our intervention to be tested. Combined with qualitative interviews, this provided insight into intervention effectiveness. Future research should test factors influencing intervention sustainability, and promote adoption of the targeted behavior and dis-adoption of competing behaviors where appropriate. PMID:24188718

Diagnostic significance of rib series in minor thorax trauma compared to plain chest film and computed tomography.

PubMed

Hoffstetter, Patrick; Dornia, Christian; Schäfer, Stephan; Wagner, Merle; Dendl, Lena M; Stroszczynski, Christian; Schreyer, Andreas G

2014-01-01

Rib series (RS) are a special radiological technique to improve the visualization of the bony parts of the chest. The aim of this study was to evaluate the diagnostic accuracy of rib series in minor thorax trauma. Retrospective study of 56 patients who received RS, 39 patients where additionally evaluated by plain chest film (PCF). All patients underwent a computed tomography (CT) of the chest. RS and PCF were re-read independently by three radiologists, the results were compared with the CT as goldstandard. Sensitivity, specificity, negative and positive predictive value were calculated. Significance in the differences of findings was determined by McNemar test, interobserver variability by Cohens kappa test. 56 patients were evaluated (34 men, 22 women, mean age =61 y.). In 22 patients one or more rib fracture could be identified by CT. In 18 of these cases (82%) the correct diagnosis was made by RS, in 16 cases (73%) the correct number of involved ribs was detected. These differences were significant (p = 0.03). Specificity was 100%, negative and positive predictive value were 85% and 100%. Kappa values for the interobserver agreement was 0.92-0.96. Sensitivity of PCF was 46% and was significantly lower (p = 0.008) compared to CT. Rib series does not seem to be an useful examination in evaluating minor thorax trauma. CT seems to be the method of choice to detect rib fractures, but the clinical value of the radiological proof has to be discussed and investigated in larger follow up studies.

A comparative evaluation of polymerization stress data obtained with four different mechanical testing systems.

PubMed

Gonçalves, Flávia; Boaro, Leticia C; Ferracane, Jack L; Braga, Roberto R

2012-06-01

The null hypothesis was that mechanical testing systems used to determine polymerization stress (σ(pol)) would rank a series of composites similarly. Two series of composites were tested in the following systems: universal testing machine (UTM) using glass rods as bonding substrate, UTM/acrylic rods, "low compliance device", and single cantilever device ("Bioman"). One series had five experimental composites containing BisGMA:TEGDMA in equimolar concentrations and 60, 65, 70, 75 or 80 wt% of filler. The other series had five commercial composites: Filtek Z250 (3M ESPE), Filtek A110 (3M ESPE), Tetric Ceram (Ivoclar), Heliomolar (Ivoclar) and Point 4 (Kerr). Specimen geometry, dimensions and curing conditions were similar in all systems. σ(pol) was monitored for 10 min. Volumetric shrinkage (VS) was measured in a mercury dilatometer and elastic modulus (E) was determined by three-point bending. Shrinkage rate was used as a measure of reaction kinetics. ANOVA/Tukey test was performed for each variable, separately for each series. For the experimental composites, σ(pol) decreased with filler content in all systems, following the variation in VS. For commercial materials, σ(pol) did not vary in the UTM/acrylic system and showed very few similarities in rankings in the others tests system. Also, no clear relationships were observed between σ(pol) and VS or E. The testing systems showed a good agreement for the experimental composites, but very few similarities for the commercial composites. Therefore, comparison of polymerization stress results from different devices must be done carefully. Copyright © 2012 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

Refractory Metal Heat Pipe Life Test - Test Plan and Standard Operating Procedures

NASA Technical Reports Server (NTRS)

Martin, J. J.; Reid, R. S.

2010-01-01

Refractory metal heat pipes developed during this project shall be subjected to various operating conditions to evaluate life-limiting corrosion factors. To accomplish this objective, various parameters shall be investigated, including the effect of temperature and mass fluence on long-term corrosion rate. The test series will begin with a performance test of one module to evaluate its performance and to establish the temperature and power settings for the remaining modules. The performance test will be followed by round-the-clock testing of 16 heat pipes. All heat pipes shall be nondestructively inspected at 6-month intervals. At longer intervals, specific modules will be destructively evaluated. Both the nondestructive and destructive evaluations shall be coordinated with Los Alamos National Laboratory. During the processing, setup, and testing of the heat pipes, standard operating procedures shall be developed. Initial procedures are listed here and, as hardware is developed, will be updated, incorporating findings and lessons learned.

Science Library of Test Items. Volume Twenty. A Collection of Multiple Choice Test Items Relating Mainly to Physics, 1.

ERIC Educational Resources Information Center

New South Wales Dept. of Education, Sydney (Australia).

As one in a series of test item collections developed by the Assessment and Evaluation Unit of the Directorate of Studies, items are made available to teachers for the construction of unit tests or term examinations or as a basis for class discussion. Each collection was reviewed for content validity and reliability. The test items meet syllabus…

Science Library of Test Items. Volume Twenty-One. A Collection of Multiple Choice Test Items Relating Mainly to Physics, 2.

ERIC Educational Resources Information Center

New South Wales Dept. of Education, Sydney (Australia).

As one in a series of test item collections developed by the Assessment and Evaluation Unit of the Directorate of Studies, items are made available to teachers for the construction of unit tests or term examinations or as a basis for class discussion. Each collection was reviewed for content validity and reliability. The test items meet syllabus…

Science Library of Test Items. Volume Twenty-Two. A Collection of Multiple Choice Test Items Relating Mainly to Skills.

ERIC Educational Resources Information Center

New South Wales Dept. of Education, Sydney (Australia).

As one in a series of test item collections developed by the Assessment and Evaluation Unit of the Directorate of Studies, items are made available to teachers for the construction of unit tests or term examinations or as a basis for class discussion. Each collection was reviewed for content validity and reliability. The test items meet syllabus…

Space Suit Portable Life Support System (PLSS) 2.0 Pre-Installation Acceptance (PIA) Testing

NASA Technical Reports Server (NTRS)

Watts, Carly; Vogel, Matthew

2016-01-01

Following successful completion of the space suit Portable Life Support System (PLSS) 1.0 development and testing in 2011, the second system-level prototype, PLSS 2.0, was developed in 2012 to continue the maturation of the advanced PLSS design which is intended to reduce consumables, improve reliability and robustness, and incorporate additional sensing and functional capabilities over the current Space Shuttle/International Space Station Extravehicular Mobility Unit (EMU) PLSS. PLSS 2.0 represents the first attempt at a packaged design comprising first generation or later component prototypes and medium fidelity interfaces within a flight-like representative volume. Pre-Installation Acceptance (PIA) is carryover terminology from the Space Shuttle Program referring to the series of test sequences used to verify functionality of the EMU PLSS prior to installation into the Space Shuttle airlock for launch. As applied to the PLSS 2.0 development and testing effort, PIA testing designated the series of 27 independent test sequences devised to verify component and subsystem functionality, perform in situ instrument calibrations, generate mapping data to define set-points for control algorithms, evaluate hardware performance against advanced PLSS design requirements, and provide quantitative and qualitative feedback on evolving design requirements and performance specifications. PLSS 2.0 PIA testing was carried out from 3/20/13 - 3/15/14 using a variety of test configurations to perform test sequences that ranged from stand-alone component testing to system-level testing, with evaluations becoming increasingly integrated as the test series progressed. Each of the 27 test sequences was vetted independently, with verification of basic functionality required before completion. Because PLSS 2.0 design requirements were evolving concurrently with PLSS 2.0 PIA testing, the requirements were used as guidelines to assess performance during the tests; after the completion of PIA testing, test data served to improve the fidelity and maturity of design requirements as well as plans for future advanced PLSS functional testing.

Evaluation of four slide test kits for the detection of human chorionic gonadotropin in urine

PubMed Central

Dietrich, Michael; French, J. A.

1974-01-01

Three “indirect-type” slide tests utilizing the principle of hemagglutination inhibition and one new “direct-type” slide test employing direct agglutination were evaluated for their sensitivity in detecting human chorionic gonadotropin (HCG) in urine. The results of positive tests in a group of woman in very early pregnancy were correlated with the “days after last menses”. In this series the direct slide test was the most accurate. A control must be used with each direct test to indicate interfering substances and when such are present a different test must be used. All tests were found to be of the relative sensitivity stated by the manufacturer. PMID:4851924

Evaluation of Series T22 Wet Tantalum Capacitors

NASA Technical Reports Server (NTRS)

Teverovsky, Alexander

2017-01-01

Several types of advanced wet tantalum capacitors, and series T22 in particular, are designed without internal Teflon sealing that is used for military grade, CLR style capacitors. This raises concerns regarding hermeticity of the single seal parts and their capability to withstand high internal gas pressures that might develop during operation in space. To address these issues, T22 series capacitors rated to 50 V and 125 V were subjected to highly accelerated life testing (HALT) at 125 C and rated voltage and step stress random vibration testing (RVT). To simulate conditions of storage or operation under increased internal gas pressure, the parts were stored at temperature of 150 C for 2500 hr (HTS150). Electrical characteristics of the parts were measured through the storage testing and the hermeticity leak rate was tested before and after HTS150. To assess thermo-mechanical robustness of the part, capacitors were manually soldered onto printed wired boards (PWB) and stressed by 1000 temperature cycles between -55 C and +125 C. The effect of temperature cycling was assessed by additional HALT at different temperatures. Results show that T22 series capacitors have robust design and can satisfy requirements for space applications.

Runway Incursion Prevention System Simulation Evaluation

NASA Technical Reports Server (NTRS)

Jones, Denise R.

2002-01-01

A Runway Incursion Prevention System (RIPS) was evaluated in a full mission simulation study at the NASA Langley Research center in March 2002. RIPS integrates airborne and ground-based technologies to provide (1) enhanced surface situational awareness to avoid blunders and (2) alerts of runway conflicts in order to prevent runway incidents while also improving operational capability. A series of test runs was conducted in a high fidelity simulator. The purpose of the study was to evaluate the RIPS airborne incursion detection algorithms and associated alerting and airport surface display concepts. Eight commercial airline crews participated as test subjects completing 467 test runs. This paper gives an overview of the RIPS, simulation study, and test results.

Can Teachers Be Evaluated by Their Students' Test Scores? Should They Be? The Use of Value-Added Measures of Teacher Effectiveness in Policy and Practice. Education Policy for Action Series

ERIC Educational Resources Information Center

Corcoran, Sean P.

2010-01-01

Value-added measures of teacher effectiveness are the centerpiece of a national movement to evaluate, promote, compensate, and dismiss teachers based in part on their students' test results. Federal, state, and local policy-makers have adopted these methods en masse in recent years in an attempt to objectively quantify teaching effectiveness and…

Insurance: An Evaluation Report for the Occupational Exploration Program.

ERIC Educational Resources Information Center

Altschuld, James W.; And Others

The evaluation report is one of seven produced for the Occupational Exploration Program (OEP), a series of simulated occupational experiences designed for junior high school students. Describing the pilot testing of the simulation dealing with the insurance field, the report contains sections describing the simulation context, evaluation…

Application of an Elastic-Plastic Methodology to Structural Integrity Evaluation,

DTIC Science & Technology

The elastic plastic fracture mechanics ( EPFM ) technology has advanced to the point where it can be used to make a realistic assessment of the...concepts of EPFM into a structural stability evaluation. The structure is modeled as a cracked test specimen either in series or parallel with a spring

Manufacturing Production: An Evaluation Report for the Occupational Exploration Program.

ERIC Educational Resources Information Center

Altschuld, James W.; And Others

The evaluation report is one of seven produced for the Occupational Exploration Program (OEP), a series of simulated occupational experiences designed for junior high school students. Describing the pilot testing of the simulation dealing with manufacturing production, the report contains sections describing the simulation context, evaluation…

Stress Reconstruction Analysis of Wheel Saw Cut Tests and Evaluation of Reconstruction Procedure

DOT National Transportation Integrated Search

1993-09-01

The report is the fourth in a series of engineering studies on railroad vehicle wheel performance. The results of saw cut tests performed on one new and one used wheel designed for a fleet of multiple unit (MU) power cars are summarized and analyzed....

Effects of coupler height mismatch on the structural integrity of railroad tank car stub sills.

DOT National Transportation Integrated Search

2001-12-01

This project evaluated the safety implications of coupler height mismatches on the integrity of railroad tank car stub sills, through a series of static and impact tests. The test car was a loaded tank car instrumented with strain gages at critical l...

Evaluation of Acadia National Park ITS field operational test : Island Explorer data analysis

DOT National Transportation Integrated Search

2003-04-01

This report is one in a series that presents the results of data used to assess the impact of the Intelligent Transportation Systems (ITS) that were part of a field operational test at Acadia National Park on Mount Desert Island off the coast of Main...

Evaluation of Acadia National Park ITS field operational test : state of Maine data analysis

DOT National Transportation Integrated Search

2003-04-01

This report is one in a series that presents the results of data used to assess the impact of the Intelligent Transportation Systems (ITS) that were part of a field operational test at Acadia National Park on Mount Desert Island off the coast of Main...

Evaluation of Acadia National Park ITS field operational test : Acadia National Park data analysis

DOT National Transportation Integrated Search

2003-04-01

This report is one in a series that presents the results of data used to assess the impact of the Intelligent Transportation Systems (ITS) that were part of a field operational test at Acadia National Park on Mount Desert Island off the coast of Main...

Using permutation tests to enhance causal inference in interrupted time series analysis.

PubMed

Linden, Ariel

2018-06-01

Interrupted time series analysis (ITSA) is an evaluation methodology in which a single treatment unit's outcome is studied serially over time and the intervention is expected to "interrupt" the level and/or trend of that outcome. The internal validity is strengthened considerably when the treated unit is contrasted with a comparable control group. In this paper, we introduce a robustness check based on permutation tests to further improve causal inference. We evaluate the effect of California's Proposition 99 for reducing cigarette sales by iteratively casting each nontreated state into the role of "treated," creating a comparable control group using the ITSAMATCH package in Stata, and then evaluating treatment effects using ITSA regression. If statistically significant "treatment effects" are estimated for pseudotreated states, then any significant changes in the outcome of the actual treatment unit (California) cannot be attributed to the intervention. We perform these analyses setting the cutpoint significance level to P > .40 for identifying balanced matches (the highest threshold possible for which controls could still be found for California) and use the difference in differences of trends as the treatment effect estimator. Only California attained a statistically significant treatment effect, strengthening confidence in the conclusion that Proposition 99 reduced cigarette sales. The proposed permutation testing framework provides an additional robustness check to either support or refute a treatment effect identified in for the true treated unit in ITSA. Given its value and ease of implementation, this framework should be considered as a standard robustness test in all multiple group interrupted time series analyses. © 2018 John Wiley & Sons, Ltd.

Adsorption of Dissolved Metals in the Berkeley Pit using Thiol-Functionalized Self-Assembled Monolayers on Mesoporous Supports (Thiol-SAMMS)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Betancourt, Amaury P.; Mattigod, Shas V.; Wellman, Dawn M.

2010-03-07

The Berkeley Pit in Butte, Montana, is heavily contaminated with dissolved metals. Adsorption and extraction of these metals can be accomplished through the use of a selective adsorbent. For this research, the adsorbent used was thiol-functionalized Self-Assembled Monolayers on Mesoporous Supports (thiol-SAMMS), which was developed at Pacific Northwest National Laboratory (PNNL). Thiol-SAMMS selectively binds to numerous types of dissolved metals. The objective of this research was to evaluate the loading and kinetics of aluminum, beryllium, copper, and zinc on thiol-SAMMS. For the loading tests, a series of Berkeley Pit water to thiol-SAMMS ratios (mL:g) were tested. These ratios were 1000:1,more » 500:1, 100:1, and 50:1. Berkeley Pit water is acidic (pH {approx} 2.5). This can affect the performance of SAMMS materials. Therefore, the effect of pH was evaluated by conducting parallel series of loading tests wherein the Berkeley Pit water was neutralized before or after addition of thiol-SAMMS, and a series of kinetics tests wherein the Berkeley Pit water was neutralized before addition of thiol-SAMMS for the first test and was not neutralized for the second test. For the kinetics tests, one Berkeley Pit water to thiol-SAMMS ratio was tested, which was 2000:1. The results of the loading and kinetics tests suggest that a significant decrease in dissolved metal concentration at Berkeley Pit could be realized through neutralization of Berkeley Pit water. Thiol-SAMMS technology has a limited application under the highly acidic conditions posed by the Berkeley Pit. However, thiol-SAMMS could provide a secondary remedial technique which would complete the remedial system and remove dissolved metals from the Berkeley Pit to below drinking water standards.« less

Meteorological conditions during the summer 1986 CITE 2 flight series

NASA Technical Reports Server (NTRS)

Shipham, Mark C.; Cahoon, Donald R.; Bachmeier, A. Scott

1990-01-01

An overview of meteorological conditions during the NASA Global Tropospheric Experiment/Chemical Instrumentation Testing and Evaluation (GTE/CITE 2) summer 1986 flight series is presented. Computer-generated isentropic trajectories are used to trace the history of air masses encountered along each aircraft flight path. The synoptic-scale wind fields are depicted based on Montgomery stream function analyses. Time series of aircraft-measured temperature, dew point, ozone, and altitude are shown to depict air mass variability. Observed differences between maritime tropical and maritime polar air masses are discussed.

Problems in Analyzing Time Series with Gaps and Their Solution with the WinABD Software Package

NASA Astrophysics Data System (ADS)

Desherevskii, A. V.; Zhuravlev, V. I.; Nikolsky, A. N.; Sidorin, A. Ya.

2017-12-01

Technologies for the analysis of time series with gaps are considered. Some algorithms of signal extraction (purification) and evaluation of its characteristics, such as rhythmic components, are discussed for series with gaps. Examples are given for the analysis of data obtained during long-term observations at the Garm geophysical test site and in other regions. The technical solutions used in the WinABD software are considered to most efficiently arrange the operation of relevant algorithms in the presence of observational defects.

Piloted simulation tests of propulsion control as backup to loss of primary flight controls for a mid-size jet transport

NASA Technical Reports Server (NTRS)

Bull, John; Mah, Robert; Davis, Gloria; Conley, Joe; Hardy, Gordon; Gibson, Jim; Blake, Matthew; Bryant, Don; Williams, Diane

1995-01-01

Failures of aircraft primary flight-control systems to aircraft during flight have led to catastrophic accidents with subsequent loss of lives (e.g. , DC-1O crash, B-747 crash, C-5 crash, B-52 crash, and others). Dryden Flight Research Center (DFRC) investigated the use of engine thrust for emergency flight control of several airplanes, including the B-720, Lear 24, F-15, C-402, and B-747. A series of three piloted simulation tests have been conducted at Ames Research Center to investigate propulsion control for safely landing a medium size jet transport which has experienced a total primary flight-control failure. The first series of tests was completed in July 1992 and defined the best interface for the pilot commands to drive the engines. The second series of tests was completed in August 1994 and investigated propulsion controlled aircraft (PCA) display requirements and various command modes. The third series of tests was completed in May 1995 and investigated PCA full-flight envelope capabilities. This report describes the concept of a PCA, discusses pilot controls, displays, and procedures; and presents the results of piloted simulation evaluations of the concept by a cross-section of air transport pilots.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Restivo, M.

SRNL Environmental and Chemical Process Technology (E&CPT) was requested to perform testing of vacuum pumps per a verbal request from the Customer, SRNL Hydrogen Processing Technology. Tritium Operations is currently having difficulties procuring the Normetex™® Model 15 m 3/hr (9 CFM) vacuum pump (formerly Normetex Pompes, now Eumeca SARL). One possible solution proposed by Hydrogen Processing Technology personnel is to use two Senior Aerospace Metal Bellows MB-601 vacuum pumps piped with the heads in series, and the pumps in series (Figure 1 below). This memorandum documents the ultimate vacuum testing that was performed to determine if this concept was amore » viable alternate vacuum pump strategy. This testing dovetails with previous pump evaluations documented in references 1 and 2.« less

Analysis and testing of numerical formulas for the initial value problem

NASA Technical Reports Server (NTRS)

Brown, R. L.; Kovach, K. R.; Popyack, J. L.

1980-01-01

Three computer programs for evaluating and testing numerical integration formulas used with fixed stepsize programs to solve initial value systems of ordinary differential equations are described. A program written in PASCAL SERIES, takes as input the differential equations and produces a FORTRAN subroutine for the derivatives of the system and for computing the actual solution through recursive power series techniques. Both of these are used by STAN, a FORTRAN program that interactively displays a discrete analog of the Liapunov stability region of any two dimensional subspace of the system. The derivatives may be used by CLMP, a FORTRAN program, to test the fixed stepsize formula against a good numerical result and interactively display the solutions.

Pulse Detonation Engine Test Bed Developed

NASA Technical Reports Server (NTRS)

Breisacher, Kevin J.

2002-01-01

A detonation is a supersonic combustion wave. A Pulse Detonation Engine (PDE) repetitively creates a series of detonation waves to take advantage of rapid burning and high peak pressures to efficiently produce thrust. NASA Glenn Research Center's Combustion Branch has developed a PDE test bed that can reproduce the operating conditions that might be encountered in an actual engine. It allows the rapid and cost-efficient evaluation of the technical issues and technologies associated with these engines. The test bed is modular in design. It consists of various length sections of both 2- and 2.6- in. internal-diameter combustor tubes. These tubes can be bolted together to create a variety of combustor configurations. A series of bosses allow instrumentation to be inserted on the tubes. Dynamic pressure sensors and heat flux gauges have been used to characterize the performance of the test bed. The PDE test bed is designed to utilize an existing calorimeter (for heat load measurement) and windowed (for optical access) combustor sections. It uses hydrogen as the fuel, and oxygen and nitrogen are mixed to simulate air. An electronic controller is used to open the hydrogen and air valves (or a continuous flow of air is used) and to fire the spark at the appropriate times. Scheduled tests on the test bed include an evaluation of the pumping ability of the train of detonation waves for use in an ejector and an evaluation of the pollutants formed in a PDE combustor. Glenn's Combustion Branch uses the National Combustor Code (NCC) to perform numerical analyses of PDE's as well as to evaluate alternative detonative combustion devices. Pulse Detonation Engine testbed.

Arcjet Testing of Advanced Conformal Ablative TPS

NASA Technical Reports Server (NTRS)

Gasch, Matthew; Beck, Robin; Agrawal, Parul

2014-01-01

A conformable TPS over a rigid aeroshell has the potential to solve a number of challenges faced by traditional rigid TPS materials (such as tiled Phenolic Impregnated Carbon Ablator (PICA) system on MSL. The compliant (high strain to failure) nature of the conformable ablative materials will allow integration of the TPS with the underlying aeroshell structure much easier and enable monolithic-like configuration and larger segments (or parts) to be used. In May of 2013 the CA250 project executed an arcjet test series in the Ames IHF facility to evaluate a phenolic-based conformal system (named Conformal-PICA) over a range of test conditions from 40-400Wcm2. The test series consisted of four runs in the 13-inch diameter nozzle. Test models were based on SPRITE configuration (a 55-deg sphere cone), as it was able to provide a combination of required heat flux, pressure and shear within a single entry. The preliminary in-depth TC data acquired during that test series allowed a mid-fidelity thermal response model for conformal-PICA to be created while testing of seam models began to address TPS attachment and joining of multiple segments for future fabrication of large-scale aeroshells. Discussed in this paper are the results.

Clinical evaluation of a novel population-based regression analysis for detecting glaucomatous visual field progression.

PubMed

Kovalska, M P; Bürki, E; Schoetzau, A; Orguel, S F; Orguel, S; Grieshaber, M C

2011-04-01

The distinction of real progression from test variability in visual field (VF) series may be based on clinical judgment, on trend analysis based on follow-up of test parameters over time, or on identification of a significant change related to the mean of baseline exams (event analysis). The aim of this study was to compare a new population-based method (Octopus field analysis, OFA) with classic regression analyses and clinical judgment for detecting glaucomatous VF changes. 240 VF series of 240 patients with at least 9 consecutive examinations available were included into this study. They were independently classified by two experienced investigators. The results of such a classification served as a reference for comparison for the following statistical tests: (a) t-test global, (b) r-test global, (c) regression analysis of 10 VF clusters and (d) point-wise linear regression analysis. 32.5 % of the VF series were classified as progressive by the investigators. The sensitivity and specificity were 89.7 % and 92.0 % for r-test, and 73.1 % and 93.8 % for the t-test, respectively. In the point-wise linear regression analysis, the specificity was comparable (89.5 % versus 92 %), but the sensitivity was clearly lower than in the r-test (22.4 % versus 89.7 %) at a significance level of p = 0.01. A regression analysis for the 10 VF clusters showed a markedly higher sensitivity for the r-test (37.7 %) than the t-test (14.1 %) at a similar specificity (88.3 % versus 93.8 %) for a significant trend (p = 0.005). In regard to the cluster distribution, the paracentral clusters and the superior nasal hemifield progressed most frequently. The population-based regression analysis seems to be superior to the trend analysis in detecting VF progression in glaucoma, and may eliminate the drawbacks of the event analysis. Further, it may assist the clinician in the evaluation of VF series and may allow better visualization of the correlation between function and structure owing to VF clusters. © Georg Thieme Verlag KG Stuttgart · New York.

Space Shuttle Projects

NASA Image and Video Library

1988-03-21

The Marshall Space Flight Center (MSFC) successfully test fired the third in a series of Transient Pressure Test Articles (TPTA) in its east test area. The test article was a short-stack solid rocket motor 52-feet long and 12-feet in diameter. The TPTA tests were designed to evaluate the effects of temperature, pressure and external loads encountered by the SRM, primarily during ignition transients. Instrumentation on the motor recorded approximately 1,000 charnels of data to verify the structural performance, thermal response, sealing capability of the redesign field, and case-to-nozzle joints. The TPTA test stand, 14-feet wide by 26-feet long by 33-feet high, was built in 1987. The TPTA series was a joint effort among Morton Thiokol, Inc., United Space Boosters, Inc., Wyle Laboratories, and MSFC. Wyle Laboratories conducted the tests for the MSFC, which manages the redesigned SRM program for NASA.

Terahertz NDE of Stressed Composite Overwrapped Pressure Vessels - Initial Testing

NASA Technical Reports Server (NTRS)

Madaras, Eric I.; Seebo, Jeffrey P.; Anatasi, Robert F.

2009-01-01

Terahertz radiation nondestructive evaluation was applied to a set of Kevlar composite overwrapped pressure vessel bottles that had undergone a series of thermal and pressure tests to simulate stress rupture effects. The bottles in these nondestructive evaluation tests were bottles that had not ruptured but had survived various times at the elevated load and temperature levels. Some of the bottles showed evidence of minor composite failures. The terahertz radiation did detect visible surface flaws, but did not detect any internal chemical or material degradation of the thin overwraps.

Advances in Educational and Psychological Testing: Theory and Applications. Evaluation in Education and Human Services Series.

ERIC Educational Resources Information Center

Hambleton, Ronald K., Ed.; Zaal, Jac N., Ed.

The 14 chapters of this book focus on the technical advances, advances in applied settings, and emerging topics in the testing field. Part 1 discusses methodological advances, Part 2 considers developments in applied settings, and Part 3 reviews emerging topics in the field of testing. Part 1 papers include: (1) "Advances in…

Standard test evaluation of graphite fiber/resin matrix composite materials for improved toughness

NASA Technical Reports Server (NTRS)

Chapman, Andrew J.

1984-01-01

Programs sponsored by NASA with the commercial transport manufacturers to develop a technology data base are required to design and build composite wing and fuselage structures. To realize the full potential of composite structures in these strength critical designs, material systems having improved ductility and interlaminar toughness are being sought. To promote systematic evaluation of new materials, NASA and the commercial transport manufacturers have selected and standardized a set of five common tests. These tests evaluate open hole tension and compression performance, compression performance after impact at an energy level of 20 ft-lb, and resistance to delamination. Ten toughened resin matrix/graphite fiber composites were evaluated using this series of tests, and their performance is compared with a widely used composite system.

Initial Evaluation of Acoustic Emission SHM of PRSEUS Multi-bay Box Tests

NASA Technical Reports Server (NTRS)

Horne, Michael R.; Madaras, Eric I.

2016-01-01

A series of tests of the Pultruded Rod Stitched Efficient Unitized Structure (PRSEUS) HWB Multi-Bay Test Article were conducted during the second quarter of 2015 at NASA Langley Research Center (LaRC) in the Combined Loads Test facility (COLTS). This report documents the Acoustic Emission (AE) data collected during those tests along with an initial analysis of the data. A more detailed analysis will be presented in future publications.

Evaluation of Branched-Narrative Virtual Patients for Interprofessional Education of Psychiatry Residents.

PubMed

Wilkening, G Lucy; Gannon, Jessica M; Ross, Clint; Brennan, Jessica L; Fabian, Tanya J; Marcsisin, Michael J; Benedict, Neal J

2017-02-01

This pilot study evaluated the utility of branched-narrative virtual patients in an interprofessional education series for psychiatry residents. Third-year psychiatry residents attended four interprofessional education advanced psychopharmacology sessions that involved completion of a branched-narrative virtual patient and a debriefing session with a psychiatric pharmacist. Pre- and post-assessments analyzed resident learning and were administered around each virtual patient. Simulation 4 served as a comprehensive review. The primary outcome was differences in pre- and post-assessment scores. Secondary outcomes included resident satisfaction with the virtual patient format and psychiatric pharmacist involvement. Post-test scores for simulations 1, 2, and 3 demonstrated significant improvement (p < 0.05) from pre-test scores. Scores for simulation 4 did not retain significance. Resident satisfaction with the branched-narrative virtual patient format and psychiatric pharmacist involvement was high throughout the series (100 %; n = 18). Although there are important methodological limitations to this study including a small sample size and absence of a comparator group, this pilot study supports the use of branched-narrative virtual patients in an interprofessional education series for advanced learners.

The 2016 NIST Speaker Recognition Evaluation

DTIC Science & Technology

2017-08-20

The 2016 NIST Speaker Recognition Evaluation Seyed Omid Sadjadi1,∗, Timothée Kheyrkhah1,†, Audrey Tong1, Craig Greenberg1, Douglas Reynolds2, Elliot...recent in an ongoing series of speaker recognition evaluations (SRE) to foster research in ro- bust text-independent speaker recognition, as well as...online evaluation platform, a fixed training data condition, more variability in test segment duration (uni- formly distributed between 10s and 60s

A pressure-packer system for conducting rising head tests in water table wells

USGS Publications Warehouse

Levy, Benjamin S.; Pannell, Lawrence J.; Dadoly, John P.

1993-01-01

The pressure system developed for fully-saturated well screens has been modified for conducting rising head tests in water table wells installed in highly permeable aquifers. The pressure system consists of a compressed air source and 1 inch diameter PVC piping with a packer attached at the end. The pressure system was evaluated in a series of rising head tests conducted in a well at a Superfund site in New England. The well was tested with slugs and with the pressure system. Within each technique, estimates of hydraulic conductivity showed no difference. Comparison of hydraulic conductivity estimates between techniques (slug test vs. pressure test) showed differences due to stratigraphy. The interval tested using slug tests crossed two stratigraphic units; the pressure system tested only one of these units. We conclude that the pressure system may be used to characterize the vertical hydraulic conductivity distribution in a series of successive tests by changing the packer position and the screened interval tested.

Executive summary.

DOT National Transportation Integrated Search

1996-08-01

Safety is a major goal of the National ITS Program. To promote safety, the Federal Highway Administration (FHWA) funded a series of Field Operational Tests to evaluate two low-cost emergency and assistance communications and rapid response devices an...

Integrated Suit Test 1 - A Study to Evaluate Effects of Suit Weight, Pressure, and Kinematics on Human Performance during Lunar Ambulation

NASA Technical Reports Server (NTRS)

Gernhardt, Michael L.; Norcross, Jason; Vos, Jessica R.

2008-01-01

In an effort to design the next generation Lunar suit, NASA has initiated a series of tests aimed at understanding the human physiological and biomechanical affects of space suits under a variety of conditions. The first of these tests was the EVA Walkback Test (ICES 2007-01-3133). NASA-JSC assembled a multi-disciplinary team to conduct the second test of the series, titled Integrated Suit Test 1 (IST-1), from March 6 through July 24, 2007. Similar to the Walkback Test, this study was performed with the Mark III (MKIII) EVA Technology Demonstrator suit, a treadmill, and the Partial Gravity Simulator in the Space Vehicle Mock-Up Facility at Johnson Space Center. The data collected for IST-1 included metabolic rates, ground reaction forces, biomechanics, and subjective workload and controllability feedback on both suited and unsuited (shirt-sleeve) astronaut subjects. For IST-1 the center of gravity was controlled to a nearly perfect position while the weight, pressure and biomechanics (waist locked vs. unlocked) were varied individually to evaluate the effects of each on the ability to perform level (0 degree incline) ambulation in simulated Lunar gravity. The detailed test methodology and preliminary key findings of IST-1 are summarized in this report.

Developing an Undergraduate Public Health Introductory Core Course Series.

PubMed

Nelson-Hurwitz, Denise C; Tagorda, Michelle; Kehl, Lisa; Buchthal, Opal V; Braun, Kathryn L

2018-01-01

The number of undergraduate public health education programs is increasing, but few publications provide examples of introductory public health courses that provide foundational knowledge and meet 2016 Council on Education in Public Health (CEPH) accreditation standards. This article presents the development and testing of a three-course, introductory series in public health at the University of Hawai'i at Mānoa (UHM). Development was informed by best pedagogical practices in education, web review of existing programs, literature review, key informant interviews, and accreditation standards. Student mastery of required concepts, domains, and competencies is assessed through testing and class assignments. Data from course evaluations, students' exit questionnaires at graduation, and faculty feedback were used to continuously evolve and adapt the curriculum. The three-course series-including Introduction to Public Health, Public Health Issues in Hawai'i, and Introduction to Global Health-was designed to provide incoming undergraduate public health students with a foundation in local, national, and global public health concepts and domains, while improving their skills in public health communication and information literacy. Data from class assignments, examinations, and later coursework suggest students are mastering the course materials and gaining required competencies. Data from course evaluation and exit questionnaires suggest that the students appreciate the series' approach and the challenge to apply course concepts locally and globally in subsequent courses. This foundational public health series provides a model for an introductory course series that can be implemented with existing resources by most programs, meets the new CEPH requirements, is well-received by students, and prepares students well for upper-division public health courses.

Separation system suitability (3S): a new criterion of chromatogram classification in HPLC based on cross-evaluation of separation capacity/peak symmetry and its application to complex mixtures of anthraquinones.

PubMed

Nowik, Witold; Héron, Sylvie; Bonose, Myriam; Tchapla, Alain

2013-10-07

A comparison of chromatograms obtained in a series of separation conditions for a given complex mixture may be done with a series of chromatographic descriptors. In this study, we used two descriptors: the number of critical pairs and symmetry of peaks, further rescaled and converted to the corresponding critical pairs' coefficient (CPc) and symmetry coefficient (Sc). Considering the difficulty of appreciating global separation quality using CPc and Sc criteria separately, as their respective values are usually uncorrelated, a double-criteria cross-evaluation system was required. For that purpose we tested the commonly used multi-criteria decision-making method - Derringer's desirability function (D) - as well as the recently introduced sum of ranking differences (SRD). To facilitate the graphical comparison of both approaches, the desirability function (D) was used in the inverse form (Dinv). The advantages and drawbacks of both evaluation methods, especially the respective under- or over-evaluation of outliers, caused us to introduce a new ranking approach, separation system suitability (3S). The obtained suitability rankings for the three tested approaches (Dinv, SRD and 3S) are different; nevertheless, 3S appears to be the most balanced and the easiest to interpret as well. The approach developed for selection of suitable systems was applied to the problem of separation of complex mixtures through the analysis of a series of standards of anthraquinone derivatives. To judge the pertinence of this evaluation, a sample containing a number of natural anthraquinones extracted from the bark of Indian mulberry (Morinda citrifolia) was analysed. In conclusion, the proposed methodology for the cross-evaluation of the series of chromatograms using single specific descriptors (CPc and Sc) through a global composite descriptor (3S) significantly simplifies the decision that separation systems are the most suitable for the separation of complex target mixtures of compounds.

Image dissector photocathode solar damage test program. [solar radiation shielding using a fast optical lens

NASA Technical Reports Server (NTRS)

Smith, R. A.

1977-01-01

Image dissector sensors of the same type which will be used in the NASA shuttle star tracker were used in a series of tests directed towards obtaining solar radiation/time damage criteria. Data were evaluated to determine the predicted level of operability of the star tracker if tube damage became a reality. During the test series a technique for reducing the solar damage effect was conceived and verified. The damage concepts are outlined and the test methods and data obtained which were used for verification of the technique's feasibility are presented. The ability to operate an image dissector sensor with the solar image focussed on the photocathode by a fast optical lens under certain conditions is feasible and the elimination of a mechanical protection device is possible.

A hybrid algorithm for clustering of time series data based on affinity search technique.

PubMed

Aghabozorgi, Saeed; Ying Wah, Teh; Herawan, Tutut; Jalab, Hamid A; Shaygan, Mohammad Amin; Jalali, Alireza

2014-01-01

Time series clustering is an important solution to various problems in numerous fields of research, including business, medical science, and finance. However, conventional clustering algorithms are not practical for time series data because they are essentially designed for static data. This impracticality results in poor clustering accuracy in several systems. In this paper, a new hybrid clustering algorithm is proposed based on the similarity in shape of time series data. Time series data are first grouped as subclusters based on similarity in time. The subclusters are then merged using the k-Medoids algorithm based on similarity in shape. This model has two contributions: (1) it is more accurate than other conventional and hybrid approaches and (2) it determines the similarity in shape among time series data with a low complexity. To evaluate the accuracy of the proposed model, the model is tested extensively using syntactic and real-world time series datasets.

A Hybrid Algorithm for Clustering of Time Series Data Based on Affinity Search Technique

PubMed Central

Aghabozorgi, Saeed; Ying Wah, Teh; Herawan, Tutut; Jalab, Hamid A.; Shaygan, Mohammad Amin; Jalali, Alireza

2014-01-01

Time series clustering is an important solution to various problems in numerous fields of research, including business, medical science, and finance. However, conventional clustering algorithms are not practical for time series data because they are essentially designed for static data. This impracticality results in poor clustering accuracy in several systems. In this paper, a new hybrid clustering algorithm is proposed based on the similarity in shape of time series data. Time series data are first grouped as subclusters based on similarity in time. The subclusters are then merged using the k-Medoids algorithm based on similarity in shape. This model has two contributions: (1) it is more accurate than other conventional and hybrid approaches and (2) it determines the similarity in shape among time series data with a low complexity. To evaluate the accuracy of the proposed model, the model is tested extensively using syntactic and real-world time series datasets. PMID:24982966

Fire prevention in California's Riverside County Headstart Project...an evaluation

Treesearch

William S. Folkman; Jean Taylor

1972-01-01

An especially designed series of fire prevention lessons were taught to preschool children in the Headstart Project in Riverside County, Calif. Their effectiveness was evaluated by observing classroom reaction and by testing the children at the end of the year. The results suggest that this type of educational approach is feasible.

A Path to Designing Inquiry Activities in Mathematics

ERIC Educational Resources Information Center

Greene, M.; von Renesse, C.

2017-01-01

This paper aims to illustrate a design cycle of inquiry-based mathematics activities. We highlight a series of questions that we use when creating inquiry-based materials, testing and evaluating those materials, and revising the materials following this evaluation. These questions highlight the many decisions necessary to find just the right tasks…

Parameterization of Movement Execution in Children with Developmental Coordination Disorder

ERIC Educational Resources Information Center

Van Waelvelde, Hilde; De Weerdt, Willy; De Cock, Paul; Janssens, Luc; Feys, Hilde; Engelsman, Bouwien C. M. Smits

2006-01-01

The Rhythmic Movement Test (RMT) evaluates temporal and amplitude parameterization and fluency of movement execution in a series of rhythmic arm movements under different sensory conditions. The RMT was used in combination with a jumping and a drawing task, to evaluate 36 children with Developmental Coordination Disorder (DCD) and a matched…

Synthesis and evaluation of new 3-phenylcoumarin derivatives as potential antidepressant agents.

PubMed

Sashidhara, Koneni V; Rao, K Bhaskara; Singh, Seema; Modukuri, Ram K; Aruna Teja, G; Chandasana, Hardik; Shukla, Shubha; Bhatta, Rabi S

2014-10-15

A series of amine substituted 3-phenyl coumarin derivatives were designed and synthesized as potential antidepressant agents. In preliminary screening, all compounds were evaluated in forced swimming test (FST), a model to screen antidepressant activity in rodents. Among the series, compounds 5c and 6a potentially decreased the immobility time by 73.4% and 79.7% at a low dose of 0.5 mg/kg as compared to standard drug fluoxetine (FXT) which reduced the immobility time by 74% at a dose of 20 mg/kg, ip. Additionally, these active compounds also exhibited significant efficacy in tail suspension test (TST) (another model to screen antidepressant compounds). Interestingly, rotarod and locomotor activity tests confirmed that these two compounds do not have any motor impairment effect and neurotoxicity in mice. Our studies demonstrate that the new 3-phenylcoumarin derivatives may serve as a promising antidepressant lead and hence pave the way for further investigation around this chemical space. Copyright © 2014 Elsevier Ltd. All rights reserved.

Intrusion of Soil Water through Pipe Cracks

EPA Science Inventory

This report describes a series of experiments conducted at U.S. EPA’s Test and Evaluation Facility in 2013-2014 to study the intrusion of contaminated soil water into a pipe crack during simulated backflow events. A test rig was used consisting of a 3’ x 3’ x 3’ acrylic soil bo...

Functional Amnesia: Clinical Description and Neuropsychological Profile of 10 Cases

ERIC Educational Resources Information Center

Kritchevsky, Mark; Chang, Judy; Squire, Larry R.

2004-01-01

We carried out the first neuropsychological study of a series of patients with functional amnesia. We evaluated 10 patients, first with a neurological examination and then with three tests of anterograde amnesia and four tests of retrograde amnesia. Excluding one patient who later admitted to malingering, all patients had a significant premorbid…

Forecasting Techniques and Library Circulation Operations: Implications for Management.

ERIC Educational Resources Information Center

Ahiakwo, Okechukwu N.

1988-01-01

Causal regression and time series models were developed using six years of data for home borrowing, average readership, and books consulted at a university library. The models were tested for efficacy in producing short-term planning and control data. Combined models were tested in establishing evaluation measures. (10 references) (Author/MES)

PLUMBBOB Series, 1957

DTIC Science & Technology

1981-09-15

Organization included radiological safety, security, transportation, cominuni- cations, engineering , and logistics. The Air Force Special Weapons Center (AFSWC...Test Organization by Reynolds Electrical and Engineering Company. Inc. * PLUMBBOB AFSWP Operation Summary Report * Weapons Test Reports for the Armed...Project 50.5 (Evaluation of’ Shielding for Engineer ileavy Equipment) .... ......... . 4.2.4 Project 50.6 (Protection Afforded by "Field

Problems in Criterion-Referenced Measurement. CSE Monograph Series in Evaluation, 3.

ERIC Educational Resources Information Center

Harris, Chester W., Ed.; And Others

Six essays on technical measurement problems in criterion referenced tests and four essays by psychometricians proposing solutions are presented: (1) "Criterion-Referenced Measurement" and Other Such Terms, by Marvin C. Alkin which is an overview of the first six papers; (2) Selecting Objectives and Generating Test Items for Objectives-Based…

REMOVAL OF MICROBIAL CONTAMINANTS IN DRINKING WATER: KOCH MEMBRANE SYSTEMS, HF-82-35-PMPW™ ULTRAFILTRATION MEMBRANE

EPA Science Inventory

Two Koch Membrane Systems HF-82-35-PMPW ultrafiltration membrane cartridges were tested for removal of viruses, bacteria, and protozoan cysts at NSF’s Drinking Water Treatment Systems Laboratory. The ETV testing was conducted as part of a series of evaluations of the Expeditiona...

Characterization of Vertical Impact Device Acceleration Pulses Using Parametric Assessment: Phase II Accelerated Free-Fall

DTIC Science & Technology

2016-04-30

support contractor , Infoscitex, conducted a series of tests to identify the performance capabilities of the Vertical Impact Device (VID). The VID is a...C. Table 3. AFD Evaluation with Red IMPAC Programmer: Data Summary Showing Means and Standard Deviations Test Cell Drop Ht . (in) Mean Peak

Performance of Loblolly Pine Seed Sources in Argentina

Treesearch

Timothy La Farge; Floyd E. Bridgwater; Mirta N. Baez

1999-01-01

Four test series of loblolly pine (Pinus taeda L.) were evaluated to determine the performance in northeastern Argentina of seed sources from three breeding populations in the southeastern United States. Three half-sib progeny tests of seed sources from Florida and Louisiana demonstrated strong genetic gains for height, dbh, and volume growth....

Centaur Standard Shroud (CSS) static ultimate load structural tests

NASA Technical Reports Server (NTRS)

1975-01-01

A series of tests were conducted on the jettisonable metallic shroud used on the Titan/Centaur launch vehicle to verify its structural capabilities and to evaluate its structural interaction with the Centaur stage. A flight configured shroud and the interfacing Titan/Centaur structural assemblies were subjected to tests consisting of combinations of applied axial and shear loads to design ultimate values, including a set of tests on thermal conditions and two dynamic response tests to verify the analytical stiffness model. The strength capabilities were demonstrated at ultimate (125 percent of design limit) loads. It was also verified that the spring rate of the flight configured shroud-to-Centaur forward structural deflections of the specimen became nonlinear, as expected, above limit load values. This test series qualification program verified that the Titan/Centaur shroud and the Centaur and Titan interface components are qualified structurally at design ultimate loads.

anticonvulsant and toxicity evaluation of newer 4H-benzo[1,4]oxazin-3-ones: The effect of two hydrogen bonding domains.

PubMed

Siddiqui, Nadeem; Ali, Ruhi; Arshad, M Faiz; Ahsan, Waquar; Ahmed, Sharique; Alam, M Shamsher

2010-11-01

A series of (Z)-2-(substituted aryl)-N-(3-oxo-4-(substituted carbamothioyl)-3,4-dihydro-2H-benzo[b][1,4]oxazin-7-yl) hydrazine carboxamides (6a-r) was synthesized using 2-amino-5-nitrophenol as a starting material. All the synthesized compounds possessed two hydrogen-bonding domains and their effect on the activity was studied thereof. The anticonvulsant activity was assessed by the maximal electroshock test (MES), subcutaneous pentylenetetrazole test (scPTZ) and intraperitoneal thiosemicarbazide test (ipTSC). Compounds (6b, 6h, 6i, and 6p) were found to be the most potent of the series as they showed 83-100% protection in the MES test. They also displayed considerable activity in the chemically induced seizure tests. Most of the tested compounds were devoid of the neurotoxic and hepatotoxic effects.

Open-source Software for Demand Forecasting of Clinical Laboratory Test Volumes Using Time-series Analysis.

PubMed

Mohammed, Emad A; Naugler, Christopher

2017-01-01

Demand forecasting is the area of predictive analytics devoted to predicting future volumes of services or consumables. Fair understanding and estimation of how demand will vary facilitates the optimal utilization of resources. In a medical laboratory, accurate forecasting of future demand, that is, test volumes, can increase efficiency and facilitate long-term laboratory planning. Importantly, in an era of utilization management initiatives, accurately predicted volumes compared to the realized test volumes can form a precise way to evaluate utilization management initiatives. Laboratory test volumes are often highly amenable to forecasting by time-series models; however, the statistical software needed to do this is generally either expensive or highly technical. In this paper, we describe an open-source web-based software tool for time-series forecasting and explain how to use it as a demand forecasting tool in clinical laboratories to estimate test volumes. This tool has three different models, that is, Holt-Winters multiplicative, Holt-Winters additive, and simple linear regression. Moreover, these models are ranked and the best one is highlighted. This tool will allow anyone with historic test volume data to model future demand.

Open-source Software for Demand Forecasting of Clinical Laboratory Test Volumes Using Time-series Analysis

PubMed Central

Mohammed, Emad A.; Naugler, Christopher

2017-01-01

Background: Demand forecasting is the area of predictive analytics devoted to predicting future volumes of services or consumables. Fair understanding and estimation of how demand will vary facilitates the optimal utilization of resources. In a medical laboratory, accurate forecasting of future demand, that is, test volumes, can increase efficiency and facilitate long-term laboratory planning. Importantly, in an era of utilization management initiatives, accurately predicted volumes compared to the realized test volumes can form a precise way to evaluate utilization management initiatives. Laboratory test volumes are often highly amenable to forecasting by time-series models; however, the statistical software needed to do this is generally either expensive or highly technical. Method: In this paper, we describe an open-source web-based software tool for time-series forecasting and explain how to use it as a demand forecasting tool in clinical laboratories to estimate test volumes. Results: This tool has three different models, that is, Holt-Winters multiplicative, Holt-Winters additive, and simple linear regression. Moreover, these models are ranked and the best one is highlighted. Conclusion: This tool will allow anyone with historic test volume data to model future demand. PMID:28400996

[The MMPI-2 test in the evaluation of the mobbing syndrome].

PubMed

Pappone, P; Santalucia, L; Del Castello, E; De Maino, V; Garofalo, E; Cappelluccio, R; Feola, D; Ruberto, M; Liotti, F

2007-01-01

MMPI-2 test is widely used in psychodiagnostic evaluation as well as in the evaluation of psychic pathologies related to psychosocial adversative events in working activities. A more efficacious use of MMPI-2 test in the working context can be achieved by the individuation of indexes able to facilitate the evaluation of mobbing syndrome. This work is based on the analysis of 150 cases (39.7% women and 60.7% men, 30 to 60 years of age), evaluated through an accurate examination of working history and a series of clinic conversations, followed by psychodiagnostic evaluation. The average of T-scores on the clinical scale, the content scale, the PK addition scale and the validation scale were calculated from tests. Pathologic high T-scores on the scales Hs, D. Hy e Pa were found in subjects having positive mobbing anamnesis. These results strongly indicate the presence of clinical specificities in workers exposed to working harassments, and that these specificities can be efficaciously evidenced by the MMPI-2 test.

Flight-test evaluation of civil helicopter terminal approach operations using differential GPS

NASA Technical Reports Server (NTRS)

Edwards, F. G.; Hegarty, D. M.

1989-01-01

A civil code differential Global Positioning System (DGPS) has been developed and flight-tested by the NASA Ames Research Center. The system was used to evaluate the performance of the DGPS for support of helicopter terminal approach operations. The airborne component of the DGPS was installed in a NASA helicopter. The ground-reference component was installed in a mobile van and equipped with a real-time VHF telemetry data link to transmit correction information to the aircraft system. An extensive series of tests was conducted to evaluate the performance of the system for several different configurations of the airborne navigation filter. This paper will describe the systems, the results of the flight tests, and the results of the posttest analysis.

Testing for nonlinearity in time series: The method of surrogate data

DOE Office of Scientific and Technical Information (OSTI.GOV)

Theiler, J.; Galdrikian, B.; Longtin, A.

1991-01-01

We describe a statistical approach for identifying nonlinearity in time series; in particular, we want to avoid claims of chaos when simpler models (such as linearly correlated noise) can explain the data. The method requires a careful statement of the null hypothesis which characterizes a candidate linear process, the generation of an ensemble of surrogate'' data sets which are similar to the original time series but consistent with the null hypothesis, and the computation of a discriminating statistic for the original and for each of the surrogate data sets. The idea is to test the original time series against themore » null hypothesis by checking whether the discriminating statistic computed for the original time series differs significantly from the statistics computed for each of the surrogate sets. We present algorithms for generating surrogate data under various null hypotheses, and we show the results of numerical experiments on artificial data using correlation dimension, Lyapunov exponent, and forecasting error as discriminating statistics. Finally, we consider a number of experimental time series -- including sunspots, electroencephalogram (EEG) signals, and fluid convection -- and evaluate the statistical significance of the evidence for nonlinear structure in each case. 56 refs., 8 figs.« less

Test Series 2. 4: detailed test plan

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

Test Series 2.4 comprises the fourth sub-series of tests to be scheduled as a part of Test Series 2, the second stage of the combustion research program to be carried out at the Grimethorpe Experimental Pressurized Fluidized Bed Combustion Facility. Test Series 2.1, the first sub-series of tests, was completed in February 1983, and the first part of the second sub-series, Test Series 2.3, in October 1983. Test Series 2.2 was completed in February 1984 after which the second part of Test Series 2.3 commenced. The Plan for Test Series 2.4 consists of 350 data gathering hours to be completedmore » within 520 coal burning hours. This document provides a brief description of the Facility and modifications which have been made following the completion of Test Series 2.1. No further modifications were made following the completion of the first part of Test Series 2.3 or Test Series 2.2. The operating requirements for Test Series 2.4 are specified. The tests will be performed using a UK coal (Lady Windsor), and a UK limestone (Middleton) both nominated by the FRG. Seven objectives are proposed which are to be fulfilled by thirteen test conditions. Six part load tests based on input supplied by Kraftwerk Union AG are included. The cascade is expected to be on line for each test condition and total cascade exposure is expected to be in excess of 450 hours. Details of sampling and special measurements are given. A test plan schedule envisages the full test series being completed within a two month calendar period. Finally, a number of contingency strategies are proposed. 3 figures, 14 tables.« less

Electrical short circuit and current overload tests on aircraft wiring

NASA Technical Reports Server (NTRS)

Cahill, Patricia

1995-01-01

The findings of electrical short circuit and current overload tests performed on commercial aircraft wiring are presented. A series of bench-scale tests were conducted to evaluate circuit breaker response to overcurrent and to determine if the wire showed any visible signs of thermal degradation due to overcurrent. Three types of wire used in commercial aircraft were evaluated: MIL-W-22759/34 (150 C rated), MIL-W-81381/12 (200 C rated), and BMS 1360 (260 C rated). A second series of tests evaluated circuit breaker response to short circuits and ticking faults. These tests were also meant to determine if the three test wires behaved differently under these conditions and if a short circuit or ticking fault could start a fire. It is concluded that circuit breakers provided reliable overcurrent protection. Circuit breakers may not protect wire from ticking faults but can protect wire from direct shorts. These tests indicated that the appearance of a wire subjected to a current that totally degrades the insulation looks identical to a wire subjected to a fire; however the 'fire exposed' conductor was more brittle than the conductor degraded by overcurrent. Preliminary testing indicates that direct short circuits are not likely to start a fire. Preliminary testing indicated that direct short circuits do not erode insulation and conductor to the extent that ticking faults did. Circuit breakers may not safeguard against the ignition of flammable materials by ticking faults. The flammability of materials near ticking faults is far more important than the rating of the wire insulation material.

Testing Report: Littleford-Day Dryer Operation: Dryer Operation Impacts of Proposed MIS Mitigation Changes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shimskey, Rick W.; Buchmiller, William C.; Elmore, Monte R.

2007-06-01

Pacific Northwest National Laboratory performed a series of tests using the Littleford Day 22-liter dryer during investigations that evaluated changes in the melter-feed composition for the Demonstration Bulk Vitrification System. During testing, a new melter-feed formulation was developed that improved dryer performance while improving the retention of waste salts in the melter feed during vitrification.

Army Helicopter Crashworthiness

DTIC Science & Technology

1983-10-01

protect the structure surrounding the occupied Cabin volume. Components. An important part of this program was to evaluate analysis methods that could...rigid (nonstroking) seats and the production BLACK HAWK helicopter crashworthy crewseat. Tests of three embalmed cadavers in the rigid seat gave mixed...CONDITIONS FOR RIGID SEAT TESTS WITH EMBALMED CADAVERS 1 CADAVER WEIGHT PEAK TEST NO. NO. AGE HEIGHT (LB) SEX ACCEL. (G) FRACTURE CONDITION SERIES #1

A 100-Year Review: Sensory analysis of milk.

PubMed

Schiano, A N; Harwood, W S; Drake, M A

2017-12-01

Evaluation of the sensory characteristics of food products has been, and will continue to be, the ultimate method for evaluating product quality. Sensory quality is a parameter that can be evaluated only by humans and consists of a series of tests or tools that can be applied objectively or subjectively within the constructs of carefully selected testing procedures and parameters. Depending on the chosen test, evaluators are able to probe areas of interest that are intrinsic product attributes (e.g., flavor profiles and off-flavors) as well as extrinsic measures (e.g., market penetration and consumer perception). This review outlines the literature pertaining to relevant testing procedures and studies of the history of sensory analysis of fluid milk. In addition, evaluation methods outside of traditional sensory techniques and future outlooks on the subject of sensory analysis of fluid milk are explored and presented. Copyright © 2017 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Pyrovalve Blowby Tests

NASA Technical Reports Server (NTRS)

Saulsberry, Regor; Keddy, Christopher P.; Julien, Howard L.

2003-01-01

The NASA White Sands Test Facility (WSTF) was requested to perform pyrovalve blowby tests in support of the Mars Observer Propulsion and Corrective Actions Test Program. Fifty-three tests were conducted in an attempt to characterize the blowby of commercial pyrovalves. Those pyrovalves used on NASA spacecraft are well represented, and the test data reported provide a basis for evaluating the performance of similar valves in other propulsion systems. The three test series conducted are subsequently described. All testing was done in the same test facility, with periodic changes that enhanced the test methodology.

Electrical Evaluation of RCA MWS5001D Random Access Memory, Volume 5, Appendix D

NASA Technical Reports Server (NTRS)

Klute, A.

1979-01-01

The electrical characterization and qualification test results are presented for the RCA MWS 5001D random access memory. The tests included functional tests, AC and DC parametric tests, AC parametric worst-case pattern selection test, determination of worst-case transition for setup and hold times, and a series of schmoo plots. Average input high current, worst case input high current, output low current, and data setup time are some of the results presented.

Electrical Evaluation of RCA MWS5001D Random Access Memory, Volume 4, Appendix C

NASA Technical Reports Server (NTRS)

Klute, A.

1979-01-01

The electrical characterization and qualification test results are presented for the RCA MWS5001D random access memory. The tests included functional tests, AC and DC parametric tests, AC parametric worst-case pattern selection test, determination of worst-case transition for setup and hold times, and a series of schmoo plots. Statistical analysis data is supplied along with write pulse width, read cycle time, write cycle time, and chip enable time data.

Electrical Evaluation of RCA MWS5501D Random Access Memory, Volume 2, Appendix a

NASA Technical Reports Server (NTRS)

Klute, A.

1979-01-01

The electrical characterization and qualification test results are presented for the RCA MWS5001D random access memory. The tests included functional tests, AC and DC parametric tests, AC parametric worst-case pattern selection test, determination of worst-case transition for setup and hold times, and a series of schmoo plots. The address access time, address readout time, the data hold time, and the data setup time are some of the results surveyed.

Performance Validity Testing in Neuropsychology: Scientific Basis and Clinical Application-A Brief Review.

PubMed

Greher, Michael R; Wodushek, Thomas R

2017-03-01

Performance validity testing refers to neuropsychologists' methodology for determining whether neuropsychological test performances completed in the course of an evaluation are valid (ie, the results of true neurocognitive function) or invalid (ie, overly impacted by the patient's effort/engagement in testing). This determination relies upon the use of either standalone tests designed for this sole purpose, or specific scores/indicators embedded within traditional neuropsychological measures that have demonstrated this utility. In response to a greater appreciation for the critical role that performance validity issues play in neuropsychological testing and the need to measure this variable to the best of our ability, the scientific base for performance validity testing has expanded greatly over the last 20 to 30 years. As such, the majority of current day neuropsychologists in the United States use a variety of measures for the purpose of performance validity testing as part of everyday forensic and clinical practice and address this issue directly in their evaluations. The following is the first article of a 2-part series that will address the evolution of performance validity testing in the field of neuropsychology, both in terms of the science as well as the clinical application of this measurement technique. The second article of this series will review performance validity tests in terms of methods for development of these measures, and maximizing of diagnostic accuracy.

Evaluation of Serodiagnostic Assays for Mycobacterium bovis Infection in Elk, White-Tailed Deer, and Reindeer in the United States

PubMed Central

Nelson, Jeffrey T.; Orloski, Kathleen A.; Lloyd, Audra L.; Camacho, Mark; Schoenbaum, Mark A.; Robbe-Austerman, Suelee; Thomsen, Bruce V.; Hall, S. Mark

2012-01-01

In 2011, the United States Department of Agriculture conducted a project in which elk (Cervus elaphus spp.), white-tailed deer (WTD) (Odocoileus virginianus), and reindeer (Rangifer tarandus) were evaluated by the single cervical tuberculin test (SCT), comparative cervical tuberculin test (CCT), and serologic tests. The rapid antibody detection tests evaluated were the CervidTB Stat-Pak (Stat-Pak), and the Dual Path Platform VetTB (DPP). Blood was collected from presumably uninfected animals prior to tuberculin injection for the SCT. A total of 1,783 animals were enrolled in the project. Of these, 1,752 (98.3%) were classified as presumably uninfected, based on originating from a captive cervid herd with no history of exposure to TB. Stat-Pak specificity estimates were 92.4% in reindeer, 96.7% in WTD, and 98.3% in elk and were not significantly different from SCT specificity estimates. Using the DPP in series on Stat-Pak antibody-positive samples improved specificity in the three species. Thirty one animals were classified as confirmed infected, based on necropsy and laboratory results, and 27/31 were antibody positive on Stat-Pak for an estimated sensitivity of 87.1%. The study findings indicate that rapid serologic tests used in series are comparable to the SCT and CCT and may have a greater ability to detect TB-infected cervids. PMID:22792512

Determination of efficiencies, loss mechanisms, and performance degradation factors in chopper controlled dc vehical motors. Section 1: Test program results and recommendations

NASA Technical Reports Server (NTRS)

Hamilton, H. B.; Strangas, E.

1980-01-01

The conventional series motor model is discussed as well as procedures for obtaining, by test, the parameters necessary for calculating performance and losses. The calculated results for operation from ripple free DC are compared with observed test results, indicating approximately 5% or less error. Experimental data indicating the influence of brush shift and chopper frequency are also presented. Both factors have a significant effect on the speed and torque relationships. The losses and loss mechanisms present in a DC series motor are examined and an attempt is made to evaluate the added losses due to harmonic currents and fluxes. Findings with respect to these losses is summarized.

AN EXPERIMENTAL EVALUATION OF THE CONTRIBUTION OF SEQUENCING, PRETESTING, AND ACTIVE STUDENT RESPONSE TO THE EFFECTIVENESS OF PROGRAMMED TV INSTRUCTION. STUDIES IN TELEVISED INSTRUCTION, REPORT 3.

ERIC Educational Resources Information Center

GROPPER, GEORGE L.; LUMSDAINE, ARTHUR A.

A SERIES OF EXPERIMENTS WAS CONDUCTED TO TEST THE EFFECTIVENESS OF TELEVISED INSTRUCTION. THIS STUDY, THE THIRD IN A SERIES, EXPLORED THE ROLE IN FIXED-PACE TELEVISION INSTRUCTION OF SOME OF THE TECHNIQUES AND PRACTICES EMPLOYED IN TEACHING-MACHINE INSTRUCTION. THREE SEPARATE EXPERIMENTS WERE CONDUCTED--(1) A JUNIOR HIGH SCHOOL LESSON ON NEWTON'S…

Effects of automobile steering characteristics on driver/vehicle system performance in discrete maneuvers

NASA Technical Reports Server (NTRS)

Klein, R. H.; Mcruer, D. T.

1975-01-01

A series of discrete maneuver tasks were used to evaluate the effects of steering gain and directional mode dynamic parameters on driver/vehicle responses. The importance and ranking of these parameters were evaluated through changes in subjective driver ratings and performance measures obtained from transient maneuvers such as a double lane change, an emergency lane change, and an unexpected obstacle. The unexpected obstacle maneuver proved more sensitive to individual driver differences than to vehicle differences. Results were based on full scale tests with an experienced test driver evaluating many different dynamic configurations plus seventeen ordinary drivers evaluating six key configurations.

Frequency-Based Spatial Correlation Assessments of the Ares I Subscale Acoustic Model Test Firings

NASA Technical Reports Server (NTRS)

Kenny, R. Jeremy; Houston, J.

2012-01-01

The Marshall Space Flight Center has performed a series of test firings to simulate and understand the acoustic environments generated for the Ares I liftoff profiles. Part of the instrumentation package had special sensor groups to assess the acoustic field spatial correlation features for the various test configurations. The spatial correlation characteristics were evaluated for all of the test firings, inclusive of understanding the diffuse to propagating wave amplitude ratios, the acoustic wave decays, and the incident angle of propagating waves across the sensor groups. These parameters were evaluated across the measured frequency spectra and the associated uncertainties for each parameter were estimated.

Effects of surface chemistry on hot corrosion life

NASA Technical Reports Server (NTRS)

Fryxell, R. E.; Leese, G. E.

1985-01-01

This program has its primary objective: the development of hot corrosion life prediction methodology based on a combination of laboratory test data and evaluation of field service turbine components which show evidence of hot corrosion. The laboratory program comprises burner rig testing by TRW. A summary of results is given for two series of burner rig tests. The life prediction methodology parameters to be appraised in a final campaign of burner rig tests are outlined.

Geography, Years 7-10, Library of Test Items. Volume Eight. Junior Secondary Items To Be Used With 1976 to 1980 H.S.C. Geography Exam. Broadsheets.

ERIC Educational Resources Information Center

Kouimanos, John, Ed.

As one in a series of test item collections developed by the Assessment and Evaluation Unit of the Directorate of Studies, items of value from past tests are made available to teachers for the construction of unit tests, term examinations or as a basis for class discussion. Each collection was reviewed for content validity and reliability. The…

Time Series Modeling of Nano-Gold Immunochromatographic Assay via Expectation Maximization Algorithm.

PubMed

Zeng, Nianyin; Wang, Zidong; Li, Yurong; Du, Min; Cao, Jie; Liu, Xiaohui

2013-12-01

In this paper, the expectation maximization (EM) algorithm is applied to the modeling of the nano-gold immunochromatographic assay (nano-GICA) via available time series of the measured signal intensities of the test and control lines. The model for the nano-GICA is developed as the stochastic dynamic model that consists of a first-order autoregressive stochastic dynamic process and a noisy measurement. By using the EM algorithm, the model parameters, the actual signal intensities of the test and control lines, as well as the noise intensity can be identified simultaneously. Three different time series data sets concerning the target concentrations are employed to demonstrate the effectiveness of the introduced algorithm. Several indices are also proposed to evaluate the inferred models. It is shown that the model fits the data very well.

Design and evaluation of a 3 million DN series-hybrid thrust bearing

NASA Technical Reports Server (NTRS)

Scibbe, H. W.; Winn, L. W.; Eusepi, M.

1976-01-01

The design and experimental evaluation of a series-hybrid thrust bearing, consisting of a 150-mm ball bearing and a centrifugally actuated, conical, fluid-film bearing, is presented. Tests were conducted up to 16,000 rpm and at this speed an axial load of 15,600 N (3500 lb) was safely supported by the hybrid bearing system. Through the series-hybrid bearing principle, the effective ball bearing speed was reduced to approximately one-half of the shaft speed. A speed reduction of this magnitude would result in a tenfold increase in the ball bearing fatigue life. A successful evaluation of fluid-film bearing lubricant supply failure was performed repeatedly at an operating speed of 10,000 rpm. A complete and smooth changeover to full-scale ball bearing operation was effected when the oil supply to the fluid-film bearing was cut off. Reactivation of the fluid-film oil supply system produced a flawless return to the original mode of hybrid operation.

Centaur Standard Shroud (CSS) static limit load structural tests

NASA Technical Reports Server (NTRS)

Eastwood, C.

1975-01-01

The structural capabilities of the jettisonable metal shroud were tested and the interaction of the shroud with the Centaur stage was evaluated. A flight-configured shroud and the assemblies of the associated Centaur stage were tested for applied axial and shear loads to flight limit values. The tests included various thermal, pressure, and load conditions to verify localized strength capabilities, to evaluate subsystem performance, and to determine the aging effect on insulation system properties. The tests series verified the strength capabilities of the shroud and of all associated flight assembles. Shroud deflections were shown to remain within allowable limits so long as load sharing members were connected between the shroud and the Centaur stage.

Control and Non-Payload Communications (CNPC) Prototype Radio - Generation 2 Flight Test Report

NASA Technical Reports Server (NTRS)

Ishac, Joseph A.; Iannicca, Dennis C.; Shalkhauser, Kurt A.; Kachmar, Brian A.

2014-01-01

NASA Glenn Research Center conducted a series of flight tests for the purpose of evaluating air-to-ground communications links for future unmanned aircraft systems (UAS). The primary objective of the test effort was to evaluate the transition of the aircraft communications from one ground station to the next, and to monitor data flow during the "hand-off" event. To facilitate the testing, ground stations were installed at locations in Cleveland, Ohio and Albany, Ohio that each provides line-of-sight radio communications with an overflying aircraft. This report describes results from the flight tests including flight parameters, received signal strength measurements, data latency times, and performance observations for the air-to-ground channel.

Respiratory disease and suicide among US coal miners: is there a relationship

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ames, R.G.

A case-control study was performed to test whether or not respiratory disease in coal miners presented a risk for suicide. While coal miners in general do not experience elevated rates of suicide, coal miners with respiratory disease have been found to have high rates of psychiatric disability, especially depressive reactions. Further, depression has been related to suicide. To test the hypothesis, 50 suicide deaths from four National Institute for Occupational Safety and Health cohorts of coal miners were matched by age at death to two series of controls, a noncancer, nonaccident control series, and a cancer control series. Using oddsmore » ratios (tested by chi-square) the risks of obstructive lung disease and coal workers pneumoconiosis were evaluated together with the risks of years of underground mining, cigarette smoking at the time of cohort creation, and ever having smoked cigarettes. Neither respiratory disease was found to pose a statistically elevated risk of suicide in this sample of U.S. white male coal miners.« less

Characterizing rainfall of hot arid region by using time-series modeling and sustainability approaches: a case study from Gujarat, India

NASA Astrophysics Data System (ADS)

Machiwal, Deepesh; Kumar, Sanjay; Dayal, Devi

2016-05-01

This study aimed at characterization of rainfall dynamics in a hot arid region of Gujarat, India by employing time-series modeling techniques and sustainability approach. Five characteristics, i.e., normality, stationarity, homogeneity, presence/absence of trend, and persistence of 34-year (1980-2013) period annual rainfall time series of ten stations were identified/detected by applying multiple parametric and non-parametric statistical tests. Furthermore, the study involves novelty of proposing sustainability concept for evaluating rainfall time series and demonstrated the concept, for the first time, by identifying the most sustainable rainfall series following reliability ( R y), resilience ( R e), and vulnerability ( V y) approach. Box-whisker plots, normal probability plots, and histograms indicated that the annual rainfall of Mandvi and Dayapar stations is relatively more positively skewed and non-normal compared with that of other stations, which is due to the presence of severe outlier and extreme. Results of Shapiro-Wilk test and Lilliefors test revealed that annual rainfall series of all stations significantly deviated from normal distribution. Two parametric t tests and the non-parametric Mann-Whitney test indicated significant non-stationarity in annual rainfall of Rapar station, where the rainfall was also found to be non-homogeneous based on the results of four parametric homogeneity tests. Four trend tests indicated significantly increasing rainfall trends at Rapar and Gandhidham stations. The autocorrelation analysis suggested the presence of persistence of statistically significant nature in rainfall series of Bhachau (3-year time lag), Mundra (1- and 9-year time lag), Nakhatrana (9-year time lag), and Rapar (3- and 4-year time lag). Results of sustainability approach indicated that annual rainfall of Mundra and Naliya stations ( R y = 0.50 and 0.44; R e = 0.47 and 0.47; V y = 0.49 and 0.46, respectively) are the most sustainable and dependable compared with that of other stations. The highest values of sustainability index at Mundra (0.120) and Naliya (0.112) stations confirmed the earlier findings of R y- R e- V y approach. In general, annual rainfall of the study area is less reliable, less resilient, and moderately vulnerable, which emphasizes the need of developing suitable strategies for managing water resources of the area on sustainable basis. Finally, it is recommended that multiple statistical tests (at least two) should be used in time-series modeling for making reliable decisions. Moreover, methodology and findings of the sustainability concept in rainfall time series can easily be adopted in other arid regions of the world.

EXPERIMENTAL STUDIES OF TRANSIENT EFFECTS IN FAST REACTOR FUELS. SERIES I. UO$sub 2$ IRRADIATIONS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Field, J.H.

1962-11-15

An experimental program to evaluate the performance of FCR and EFCR fuel during transient operation is outlined, and the initial series of tests are described in some detail. Test results from five experiments in the TREAT reactor, using 1-in. OD SS-clad UO/sub 2/ fuel specimens, are compared with regard to fuel temperatures, mechanical integrity, and post-irradiation appearance. Incipient fuel pin failure limits for transients are identified with maximum fuel temperatures in the range of 7000 deg F. Multiple transient damage to the cladding is likely for transients above the melting point of the fuel. (auth)

Performance of rapid tests and algorithms for HIV screening in Abidjan, Ivory Coast.

PubMed

Loukou, Y G; Cabran, M A; Yessé, Zinzendorf Nanga; Adouko, B M O; Lathro, S J; Agbessi-Kouassi, K B T

2014-01-01

Seven rapid diagnosis tests (RDTs) of HIV were evaluated by a panel group who collected serum samples from patients in Abidjan (HIV-1 = 203, HIV-2 = 25, HIV-dual = 25, HIV = 305). Kit performances were recorded after the reference techniques (enzyme-linked immunosorbent assay). The following RDTs showed a sensitivity of 100% and a specificity higher than 99%: Determine, Oraquick, SD Bioline, BCP, and Stat-Pak. These kits were used to establish infection screening strategies. The combination with 2 or 3 of these tests in series or parallel algorithms showed that series combinations with 2 tests (Oraquick and Bioline) and 3 tests (Determine, BCP, and Stat-Pak) gave the best performances (sensitivity, specificity, positive predictive value, and negative predictive value of 100%). However, the combination with 2 tests appeared to be more onerous than the combination with 3 tests. The combination with Determine, BCP, and Stat-Pak tests serving as a tiebreaker could be an alternative to the HIV/AIDS serological screening in Abidjan.

Flight test summary of modified fuel systems

NASA Technical Reports Server (NTRS)

Barrett, B. G.

1976-01-01

Two different aircraft designs, each with two modified fuel control systems, were evaluated. Each aircraft was evaluated in a given series of defined ground and flight conditions while quantitative and qualitative observations were made. During this program, some ten flights were completed, and a total of about 13 hours of engine run time was accumulated by the two airplanes. The results of these evaluations with emphasis on the operational and safety aspects were analyzed. Ground tests of the engine alone were not able to predict acceptable limiting lean mixture settings for the flight envelopes of the Cessna Models 150 and T337.

Next-generation foundations for special trackwork phase III : final report.

DOT National Transportation Integrated Search

2016-05-01

Transportation Technology Center, Inc. (TTCI) conducted a series of tests, funded by the Federal Railroad Administration, which evaluated the potential beneficial effects of various configurations of high angle frogs and frog foundations on wheel-rai...

Using vs. Being Used by School Information Systems.

ERIC Educational Resources Information Center

Sirotnik, Kenneth A.

This is one of a series of reports based on an ongoing reality test of systemic evaluation for instructional decision making. This feasibility study is being carried out by the Center for the Study of Evaluation with the Laboratory in School and Community Relations at a suburban Los Angeles high school (called Site A). Viewing a school as a…

Evaluating the Effectiveness of a Non-Cognitive Assessment Instrument

ERIC Educational Resources Information Center

Di Tommaso, Kathrynn

2016-01-01

This paper presents a pilot study aiming to evaluate the effects of a non-cognitive assessment instrument which was developed and tailored for a community college in the New York City area. The instrument was pilot tested on a group of developmental students and asked a series of questions to determine the campus support services that might best…

An astronomer's guide to period searching

NASA Astrophysics Data System (ADS)

Schwarzenberg-Czerny, A.

2003-03-01

We concentrate on analysis of unevenly sampled time series, interrupted by periodic gaps, as often encountered in astronomy. While some of our conclusions may appear surprising, all are based on classical statistical principles of Fisher & successors. Except for discussion of the resolution issues, it is best for the reader to forget temporarily about Fourier transforms and to concentrate on problems of fitting of a time series with a model curve. According to their statistical content we divide the issues into several sections, consisting of: (ii) statistical numerical aspects of model fitting, (iii) evaluation of fitted models as hypotheses testing, (iv) the role of the orthogonal models in signal detection (v) conditions for equivalence of periodograms (vi) rating sensitivity by test power. An experienced observer working with individual objects would benefit little from formalized statistical approach. However, we demonstrate the usefulness of this approach in evaluation of performance of periodograms and in quantitative design of large variability surveys.

Synthesis and Evaluation of Novel Oxyalkylated Derivatives of 2',4'-Dihydroxychalcone as Anti-Oomycete Agents against Bronopol Resistant Strains of Saprolegnia sp.

PubMed

Flores, Susana; Montenegro, Iván; Villena, Joan; Cuellar, Mauricio; Werner, Enrique; Godoy, Patricio; Madrid, Alejandro

2016-08-22

A series of novel oxyalkylchalcones substituted with alkyl groups were designed and synthesized, and the antioomycete activity of the series was evaluated in vitro against Saprolegnia strains. All tested O-alkylchalcones were synthesized by means of nucleophilic substitution from the natural compound 2',4'-dihydroxychalcone (1) and the respective alkyl bromide. The natural chalcone (1) and 10 synthetic oxyalkylchalcones (2-11) were tested against Saprolegnia parasitica and Saprolegnia australis. Among synthetic analogs, 2-hydroxy,4-farnesyloxychalcone (11) showed the most potent activity against Saprolegnia sp., with MIC and MOC values of 125 µg/mL (similar to bronopol at 150 µg/mL) and 175 µg/mL, respectively; however, 2',4'-dihydroxychalcone (1) was the strongest and most active molecule, with MIC and MOC values of 6.25 µg/mL and 12.5 µg/mL.

Thoracic Injury Risk Curves for Rib Deflections of the SID-IIs Build Level D.

PubMed

Irwin, Annette L; Crawford, Greg; Gorman, David; Wang, Sikui; Mertz, Harold J

2016-11-01

Injury risk curves for SID-IIs thorax and abdomen rib deflections proposed for future NCAP side impact evaluations were developed from tests conducted with the SID-IIs FRG. Since the floating rib guide is known to reduce the magnitude of the peak rib deflections, injury risk curves developed from SID-IIs FRG data are not appropriate for use with SID-IIs build level D. PMHS injury data from three series of sled tests and one series of whole-body drop tests are paired with thoracic rib deflections from equivalent tests with SID-IIs build level D. Where possible, the rib deflections of SID-IIs build level D were scaled to adjust for differences in impact velocity between the PMHS and SID-IIs tests. Injury risk curves developed by the Mertz-Weber modified median rank method are presented and compared to risk curves developed by other parametric and non-parametric methods.

FOOT ECZEMA: THE ROLE OF PATCH TEST IN DETERMINING THE CAUSATIVE AGENT USING STANDARD SERIES

PubMed Central

Priya, K S; Kamath, Ganesh; Martis, Jacintha; D, Sukumar; Shetty, Narendra J; Bhat, Ramesh M; Kishore, B Nanda

2008-01-01

Foot dermatitis refers to the predominant involvement of feet in the eczematous process. This study is undertaken to determine the clinical pattern and causative agent in foot eczema and to evaluate the role of patch testing in determining the causative agent of foot eczema. Data was collected from 50 patients with foot eczema, who attended the out-patient department. The patch test was performed using Indian standard series. Patch test was positive in 88% of the patients. The most common site affected was the dorsal aspect of the foot (48%) and scaly plaque was the predominant morphological pattern. The highest number of patients (24%) showed positive reactions to mercaptobenzothiazole (MBT) and the lowest (4%) to neomycin sulfate. Rubber and rubber chemicals have been reported worldwide to be the most common sensitizer causing foot eczema. Thus, patch test has a major role in finding out the cause of foot eczema. PMID:19881990

Preparations for flight research to evaluate actuated forebody strakes on the F-18 high-alpha research vehicle

NASA Technical Reports Server (NTRS)

Murri, Daniel G.; Shah, Gautam H.; Dicarlo, Daniel J.

1994-01-01

As part of the NASA High-Angle-of-Attack Technology Program (HATP), flight tests are currently being conducted with a multi-axis thrust vectoring system applied to the NASA F-18 High Alpha Research Vehicle (HARV). A follow-on series of flight tests with the NASA F-18 HARV will be focusing on the application of actuated forebody strake controls. These controls are designed to provide increased levels of yaw control at high angles of attack where conventional aerodynamic controls become ineffective. The series of flight tests are collectively referred to as the Actuated Nose Strakes for Enhanced Rolling (ANSER) Flight Experiment. The development of actuated forebody strake controls for the F-18 HARV is discussed and a summary of the ground tests conducted in support of the flight experiment is provided. A summary of the preparations for the flight tests is also provided.

THE FATE OF TRACE METALS IN A ROTARY KILN INCINERATOR WITH A VENTURI/PACKED COLUMN SCRUBBER - VOLUME I: TECHNICAL RESULTS

EPA Science Inventory

A five week series of pilot-scale incineration tests, using a synthetic waste feed, was performed at the Environmental Protection Agency's Incineration Research Facility to evaluate the fate of trace metals fed to a rotary kiln incinerator. Eight tests studied the fate of five ha...

An Experimental Study of Contaminant Intrusion Through Pipe Cracks

EPA Science Inventory

This report describes a series of experiments conducted at U.S. EPA’s Test and Evaluation Facility in 2013-2014 to study the intrusion of contaminated soil water into a pipe crack during simulated backflow events. A test rig was used consisting of a 3’ x 3’ x 3’ acrylic soil bo...

Anthropometry of a Fit Test Sample used in Evaluating the Current and Improved MCU-2/P Masks

DTIC Science & Technology

1989-03-01

METHOD Forty-two head and face measurements were taken on each subject after he/she had completed MSA’s series of fit tests. Of these, 15 were measured...BREADTH Using spreading calipers, the hori- zontal distance between the fronto- temporale landmarks. 25 MEASUREMENT DESCRIPTIONS (cont’d) 13. NASAL

MTF Database: A Repository of Students' Academic Performance Measurements for the Development of Techniques for Evaluating Team Functioning

ERIC Educational Resources Information Center

Hsiung, Chin-Min; Zheng, Xiang-Xiang

2015-01-01

The Measurements for Team Functioning (MTF) database contains a series of student academic performance measurements obtained at a national university in Taiwan. The measurements are acquired from unit tests and homework tests performed during a core mechanical engineering course, and provide an objective means of assessing the functioning of…

Testing and Evaluating C3I Systems That Employ AI. Volume 1. Handbook for Testing Expert Systems

DTIC Science & Technology

1991-01-31

Designs ....... ............. .. 6-29 Nonequivalent Control Group Design ...does not receive the system; and (c) nonequivalent (and nonrandomized) control group designs that rely on statistical techniques like analysis of...implementation); (b) multiple time-series designs using a control group ; and (c) nonequivalent control group designs that obtain pretest and

Assessing the Value-Added by the Environmental Testing Process with the Aide of Physics/Engineering of Failure Evaluations

NASA Technical Reports Server (NTRS)

Cornford, S.; Gibbel, M.

1997-01-01

NASA's Code QT Test Effectiveness Program is funding a series of applied research activities focused on utilizing the principles of physics and engineering of failure and those of engineering economics to assess and improve the value-added by the various validation and verification activities to organizations.

Characteristics of patients with lower extremity symptoms treated with slump stretching: a case series.

PubMed

George, Steven Z

2002-08-01

Prospective case series. The purpose of this case series was to describe the criteria used to determine if patients were to receive slump stretch treatment within a treatment-based classification system and to describe selected symptom characteristics associated with these patients. Previous reports from the literature suggest that the slump test position may be a useful treatment and evaluation technique. However, little information has been presented regarding how to identify patients who are appropriate to treat with slump stretching and the symptom characteristics associated with these patients. Prior to recruitment, criteria were established to identify patients who would be considered appropriate to treat with slump stretching. Consecutive patients referred with low back diagnosis or low-back-related diagnoses were then evaluated using a treatment-based classification system. Selected symptom characteristics were collected from patients treated with slump stretching. Out of 88 consecutive patients with low back diagnoses or low-back-related diagnoses, 6 met the study's inclusion criteria and were treated with slump stretching. All pain diagrams were classified as "organic" or "possibly organic," and the most common symptom descriptor was "deep ache." At the discharge session of physical therapy, 5 of 6 patients had symptoms that were more proximally located and all patients reported a decrease in symptom intensity. Favorable changes in symptom intensity and location were observed for this case series, but definitive conclusions cannot be drawn from this study design. Additional research needs to be completed to determine if the slump test position is an effective evaluation and treatment technique.

Charge-Control Unit for Testing Lithium-Ion Cells

NASA Technical Reports Server (NTRS)

Reid, Concha M.; Mazo, Michelle A.; Button, Robert M.

2008-01-01

A charge-control unit was developed as part of a program to validate Li-ion cells packaged together in batteries for aerospace use. The lithium-ion cell charge-control unit will be useful to anyone who performs testing of battery cells for aerospace and non-aerospace uses and to anyone who manufacturers battery test equipment. This technology reduces the quantity of costly power supplies and independent channels that are needed for test programs in which multiple cells are tested. Battery test equipment manufacturers can integrate the technology into their battery test equipment as a method to manage charging of multiple cells in series. The unit manages a complex scheme that is required for charging Li-ion cells electrically connected in series. The unit makes it possible to evaluate cells together as a pack using a single primary test channel, while also making it possible to charge each cell individually. Hence, inherent cell-to-cell variations in a series string of cells can be addressed, and yet the cost of testing is reduced substantially below the cost of testing each cell as a separate entity. The unit consists of electronic circuits and thermal-management devices housed in a common package. It also includes isolated annunciators to signal when the cells are being actively bypassed. These annunciators can be used by external charge managers or can be connected in series to signal that all cells have reached maximum charge. The charge-control circuitry for each cell amounts to regulator circuitry and is powered by that cell, eliminating the need for an external power source or controller. A 110-VAC source of electricity is required to power the thermal-management portion of the unit. A small direct-current source can be used to supply power for an annunciator signal, if desired.

APPLICATION OF THE AERIAL PROFILING OF TERRAIN SYSTEM.

USGS Publications Warehouse

Cyran, Edward J.

1985-01-01

The U. S. Geological Survey has completed the performance evaluation flight tests of the Aerial Profiling of Terrain System (APTS) and is now performing a series of application tests to determine its effectiveness and efficiency as an earth-science data collection tool. These tests are designed to evaluate the APTS at such tasks as positioning water wells, testing reliability of older maps, measuring elevations of kettle ponds, and profiling stream valleys for flood studies. The results of three application tests in Massachusetts are discussed: positioning water wells and measuring elevations along the Charles River; testing four older 1:24,000-scale quadrangle maps in the Plymouth area; and measuring elevations of several hundred kettle ponds near the Cape Cod Canal.

Test Review: Reynolds, C. R., Voress, J. V., Kamphaus, R. W. (2015), "Mathematics Fluency and Calculation Tests (MFaCTs) review." PRO-ED

ERIC Educational Resources Information Center

Marbach, Joshua

2017-01-01

The Mathematics Fluency and Calculation Tests (MFaCTs) are a series of measures designed to assess for arithmetic calculation skills and calculation fluency in children ages 6 through 18. There are five main purposes of the MFaCTs: (1) identifying students who are behind in basic math fact automaticity; (2) evaluating possible delays in arithmetic…

Development and Refinement of Reading and Mathematics Tests for Grades 2 and 5. Beginning Teacher Evaluation Study. Technical Report Series. Technical Report III-1. Continuation of Phase III A.

ERIC Educational Resources Information Center

Filby, Nikola N.; Dishaw, Marilyn

Achievement tests that are maximally sensitive to effective instruction in reading and mathematics for grades 2 and 5 were developed and refined. Important considerations regarding the tests' validity were: its coverage of instructional content (opportunity to learn), and its reactivity to instruction. Student ability must be minimally related to…

Evaluation of GasmetTM DX-4015 Series Fourier Transform Infrared Gas Analyzer

DTIC Science & Technology

2009-06-01

penalty for failing to comply with a collection of information if it does not display a currently valid OMB control number PLEASE DO NOT RETURN YOUR...Series FTIR Gas Analyzer Instrument test conditions simulated current ALS Increment 0 conditions. Briefly, unknown samples are collected in a "hot...a 1M cell. Emission radiation can be collected following a reflection or transmission process. Only one system is being considered and that system

Experimental evaluation of P-Y curves considering liquefaction development.

DOT National Transportation Integrated Search

2010-12-01

This report presents details and findings of a test series conducted on a single pile embedded in homogeneous saturated Nevada sand, which was subjected to sequential dynamic shaking and lateral (inertial-equivalent) loading. This report documents th...

Torsion testing for general constitutive relations: Gilles Canova's Master's Thesis

NASA Astrophysics Data System (ADS)

Kocks, U. F.; Stout, M. G.

1999-09-01

Torsion testing is useful but cumbersome: useful as a technique to determine large-strain plastic behaviour in a plane-strain mode; cumbersome because the testing of a solid rod provides reliable data in only the simplest of circumstances, for example, when there is no strain hardening or rate sensitivity. The testing of short thin-walled tubes is widely regarded as the best current technique to determine general constitutive behaviour; a drawback is the requirement for large specimen blanks (say, 3 cm cube) and the complex machining procedure. Gilles Canova proposed an alternative - the testing of a series of solid rods of differing diameters, proving the principle by using 10 such rods for one test. We have undertaken a similar series of tests on just four rods plus one short tube for comparison. We found the results from the two types of torsion test in excellent agreement; however, it was not a critical test, inasmuch as the rate sensitivity of the pure copper used was too small. Had it been greater (as, for example, in aluminium and at higher temperature), the evaluation of perhaps six rods would have provided the constitutive response with regard to both hardening and rate sensitivity at the same time - which would require two short-tube tests (plus duplications). The main drawback of the multiple-rod test is that it requires considerable numerical effort in the evaluation. A closer integration with modelling of the constitutive behaviour would be helpful.

Supplemental tests in the evaluation of occupational hand dermatitis in soldiers.

PubMed

Wolf, R; Movshowitz, M; Brenner, S

1996-03-01

Hand dermatitis in soldiers is a considerable problem. The purpose of the study was to evaluate appropriate screening tests to improve the diagnosis of hand dermatitis in soldiers. A group of 111 soldiers with occupational dermatitis from contact with fuels and oils underwent "tailored patch tests" with allergens relevant to their field of work and their environment. The control group consisted of 24 soldiers with various jobs similar to those of civilian life, who had not been exposed to oils and fuels. Seventy-three civilian patients, attending the clinic for patch testing, were also included. Twenty soldiers, who had a history of intensive contact with oil and fuels, but no contact dermatitis, and who were admitted because of various skin diseases (fungal infections, acne, etc.) also underwent the supplemental testing and served as an additional control group. Of the soldiers, 31 (29%) showed one or more positive skin tests of the oil series and 30 patients of this group one or more positive reactions to the standard patch tests trays. No patient of the control groups had a positive test to the oil series. Our results show the value of the supplementary tests as a first-step screening test for detection of oil allergy in soldiers and automobile-mechanics or in workers handling other gasoline- or diesel-powered engineering equipment. The test method appears to be practical, easy to perform, reliable and giving clear and accurate results, with a negligible rate of false positive reactions.

Linear Array Ultrasonic Testing Of A Thick Concrete Specimens For Non-Destructive Evaluation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Clayton, Dwight A.; Khazanovich, Lev; Zammerachi, Mattia

The University of Minnesota and Oak Ridge National Laboratory are collaborating on the design and construction of a concrete specimen with sufficient reinforcement density and cross-sectional size to represent a light water reactor (LWR) containment wall with various defects. The preliminary analysis of the collected data using extended synthetic aperture focussin technique (SAFT) reconstruction indicated a great potential of the ultrasound array technology for locating relatively shallow distresses. However, the resolution and reliability of the analysis is inversely proportional to the defect depth and the amount of reinforcement between the measurement point and the defect location. The objective of thismore » round of testing is to evaluate repeatability of the obtained reconstructions from measurements with different frequencies as well as to examine the effect of the duration of the sending ultrasound signal on the resulting reconstructions. Two series of testing are performed in this study. The objective of the first series is to evaluate repeatability of the measurements and resulting reconstructed images. The measurements use three center frequencies. Five measurements are performed at each location with and without lifting the device. The analysis of the collected data suggested that a linear array ultrasound system can produce reliably repeatable reconstructions using 50 kHz signals for relatively shallow depths (less than 0.5 m). However, for reconstructions at the greater depths the use of lower frequency and/or signal filtering to reduce the effect of signal noise may be required. The objective of the second series of testing is to obtain measurements with various impulse signal durations. The entire grid on the smooth surface is tested with four different various impulse signal durations. An analysis of the resulting extended SAFT reconstructions suggested that Kirchhoff-based migration leads to easier interpreting reconstructions when shorter duration impulse is used. Longer duration impulses may provide useful information for model-based reconstructions.« less

Test Series 2. 2: Detailed Test Plan

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

Test Series 2.2 comprises the third sub-series of tests to be scheduled as a part of Test Series 2, the second stage of the combustion research program to be carried out at the Grimethorpe Experimental Pressurized Fluidized Bed Combustion Facility. Test Series 2.1, the first sub-series of tests, was completed in February 1983, and the first half of the second sub-series, Test Series 2.3, in October 1983. Test Series 2.2 is to consist of 350 data gathering hours, which it is hoped to complete within 560 coal burning hours. This document provides a brief description of the Facility and modificationsmore » which have been made following the completion of Test Series 2.1. No further modifications were made following the completion of the first half of Test Series 2.3. The operating requirements are specified. The tests will be performed using a UK coal (Kiveton Park), and a UK limestone (Middleton) both nominated by the FRG. Nine objectives are proposed which are to be fulfilled by thirteen test conditions. Six part load tests are included, as defined by Kraftwerk Union AG. The cascade is expected to be on line for each test condition and total cascade exposure is expected to be in excess of 450 hours. Details of sampling and special measurements are given. A test plan schedule envisages the test series being completed within a two month calendar period. Finally, a number of contingency strategies are proposed.« less

Design, synthesis and biological evaluation of novel ring-opened cromakalim analogues with relaxant effects on vascular and respiratory smooth muscles and as stimulators of elastin synthesis.

PubMed

Bouhedja, Mourad; Peres, Basile; Fhayli, Wassim; Ghandour, Zeinab; Boumendjel, Ahcène; Faury, Gilles; Khelili, Smail

2018-01-20

Two new series of ring-opened analogues of cromakalim bearing sulfonylurea moieties (series A: with N-unmethylated sulfonylureas, series B: with N-methylated sulfonylureas) were synthesized and tested as relaxants of vascular and respiratory smooth muscles (rat aorta and trachea, respectively). Ex vivo biological evaluations indicated that the most active compounds, belonging to series B, displayed a marked vasorelaxant activity on endothelium-intact aortic rings and the trachea. A majority of series B compounds exhibited a higher vasorelaxant activity (EC 50  < 22 μM) than that of the reference compound diazoxide (EC 50  = 24 μM). Interestingly, several tested compounds of series B also presented stronger relaxant effects on the trachea than the reference compound cromakalim (EC 50  = 124 μM), in particular compounds B4, B7 and B16 (EC 50  < 10 μM). By contrast, series A derivatives were poorly active on aortic rings (EC 50  > 57 μM for all, and EC 50  > 200 μM for a majority of them), but some of them showed an interesting relaxing effect on trachea (i.e. A15 and A33, EC 50  = 30 μM). The most potent compounds of both series, i.e. A15, A33 and B16, tested on aortic rings in the presence of glibenclamide or 80 mM KCl, suggested that they acted as voltage-gated Ca 2+ channel blockers, like verapamil, instead of being ATP-potassium channel activators, as is cromakalim, the parent molecule. Further investigations on cultured vascular smooth muscle cells showed a strong stimulating effect on elastin synthesis, especially compound B16, which was more active at 20 μM than diazoxide, a reference ATP-sensitive potassium channel activator. Taken together, our results show that the N-methylation of the sulfonylurea moieties of ring-opened cromakalim analogues led to new compounds blocking calcium-gated channels, which had a major impact on the arterial and tracheal activities as well as selectivity. Copyright © 2017 Elsevier Masson SAS. All rights reserved.

Fish Passage Through a Simulated Horizontal Bulb Turbine Pressure Regime: A Supplement to"Laboratory Studies of the Effects of Pressure and Dissolved Gas Supersaturation on Turbine-Passed Fish"

DOE Office of Scientific and Technical Information (OSTI.GOV)

Abernethy, Cary S.; Amidan, Brett G.; Cada, G F.

Migratory and resident fish in the Columbia River Basin are exposed to stresses associated with hydroelectric power production, including pressure changes during turbine passage. The responses of fall chinook salmon and bluegill sunfish to rapid pressure change was investigated at the Pacific Northwest National Laboratory. Previous test series evaluated the effects of passage through a vertical Kaplan turbine under the"worst case" pressure conditions and under less severe conditions where pressure changes were minimized. For this series of tests, pressure changes were modified to simulate passage through a horizontal bulb turbine, commonly installed at low head dams. The results were comparedmore » to results from previous test series. Migratory and resident fish in the Columbia River Basin are exposed to stresses associated with hydroelectric power production, including pressure changes during turbine passage. The responses of fall chinook salmon and bluegill sunfish to rapid pressure change was investigated at the Pacific Northwest National Laboratory. Previous test series evaluated the effects of passage through a vertical Kaplan turbine under the"worst case" pressure conditions and under less severe conditions where pressure changes were minimized. For this series of tests, pressure changes were modified to simulate passage through a horizontal bulb turbine, commonly installed at low head dams. The results were compared to results from previous test series. Both fish species were acclimated for 16-22 hours at either surface (101 kPa; 1 atm) or 30 ft (191 kPa; 1.9 atm) of pressure in a hyperbaric chamber before exposure to a pressure scenario simulating passage through a horizontal bulb turbine. The simulation was as follows: gradual pressure increase to about 2 atm of pressure, followed by a sudden (0.4 second) decrease in pressure to either 0.7 or 0.95 atm, followed by gradual return to 1 atm (surface water pressure). Following the exposure, fish were held at surface pressure for a 48-hour post exposure observation period. No fall chinook salmon died during or after exposure to the horizontal bulb turbine passage pressures, and no injuries were observed during the 48-hour post exposure observation period. As with the previous test series, it cannot be determined whether fall chinook salmon acclimated to the greater water pressure during the pretest holding period. For bluegill sunfish exposed to the horizontal bulb turbine turbine-passage pressures, only one fish died and injuries were less severe and less common than for bluegills subjected to either the"worst case" pressure or modified Kaplan turbine pressure conditions in previous tests. Injury rates for bluegills were higher at 0.7 atm nadir than for the 0.95 atm nadir. However, injuries were limited to minor internal hemorrhaging. Bluegills did not suffer swim bladder rupture in any tested scenarios. Tests indicated that for most of the cross-sectional area of a horizontal bulb turbine, pressure changes occurring during turbine passage are not harmful to fall chinook salmon and only minimally harmful to bluegill. However, some areas within a horizontal bulb turbine may have extreme pressure conditions that would be harmful to fish. These scenarios were not tested because they represent a small cross-sectional area of the turbine compared to the centerline pressures scenarios used in these tests.« less

Developing an Undergraduate Public Health Introductory Core Course Series

PubMed Central

Nelson-Hurwitz, Denise C.; Tagorda, Michelle; Kehl, Lisa; Buchthal, Opal V.; Braun, Kathryn L.

2018-01-01

The number of undergraduate public health education programs is increasing, but few publications provide examples of introductory public health courses that provide foundational knowledge and meet 2016 Council on Education in Public Health (CEPH) accreditation standards. This article presents the development and testing of a three-course, introductory series in public health at the University of Hawai‘i at Mānoa (UHM). Development was informed by best pedagogical practices in education, web review of existing programs, literature review, key informant interviews, and accreditation standards. Student mastery of required concepts, domains, and competencies is assessed through testing and class assignments. Data from course evaluations, students' exit questionnaires at graduation, and faculty feedback were used to continuously evolve and adapt the curriculum. The three-course series—including Introduction to Public Health, Public Health Issues in Hawai‘i, and Introduction to Global Health—was designed to provide incoming undergraduate public health students with a foundation in local, national, and global public health concepts and domains, while improving their skills in public health communication and information literacy. Data from class assignments, examinations, and later coursework suggest students are mastering the course materials and gaining required competencies. Data from course evaluation and exit questionnaires suggest that the students appreciate the series' approach and the challenge to apply course concepts locally and globally in subsequent courses. This foundational public health series provides a model for an introductory course series that can be implemented with existing resources by most programs, meets the new CEPH requirements, is well-received by students, and prepares students well for upper-division public health courses. PMID:29892596

An evaluation of uranium-series dating of fossil echinoids from southern California Pleistocene marine terraces

USGS Publications Warehouse

Muhs, D.R.; Kennedy, G.L.

1985-01-01

Fossil sea urchins (Strongylocentrotus) from Pleistocene marine terraces on the southern California Channel Islands have been dated by the uranium-series method in order to test the suitability of echinoids for dating marine terraces. Results indicate that urchin plates and spines do not behave as closed systems with respect to both uranium and thorium. Calculated ages based on these data do not agree with uranium-series ages (120,000 and 127,000 yrs) obtained previously from corals from the same localities. Thus, fossil sea urchins (Strongylocentrotus) are not considered suitable for uraniumseries dating of Pleistocene marine terrace deposits. ?? 1985.

Contextual Influences in Developing a School-Based Comprehensive Information System.

ERIC Educational Resources Information Center

Dorr-Bremme, Donald W.

This is one of a series of reports based on an ongoing reality test of systemic evaluation for instructional decision making. This feasibility study is being carried out by the Center for the Study of Evaluation with the Laboratory in School and Community Relations at a suburban Los Angeles high school (called Site A). Viewing a school as a…

Delineation of State Agency, Accreditation, and Institutional Responsibilities. Improving Community College Evaluation and Planning: Project Working Paper Number Four.

ERIC Educational Resources Information Center

California Community Colleges, Sacramento. Office of the Chancellor.

One of a series of papers resulting from a Fund for the Improvement of Postsecondary Education (FIPSE) project to improve evaluation and planning in community colleges, this working paper presents a plan of purposes and activities to experimentally test a model of delineation of responsibilities among accrediting commissions, state agencies, and…

Me and My Environment Formative Evaluation Report 2. Assessing Student Abilities and Performance: Year 1.

ERIC Educational Resources Information Center

Steele, Joe M.

Presented is the second in a series of formative evaluation reports which summarizes student abilities and performance in field tests of Me and My Environment, a 3-year life science curriculum for 13- to 16-year-old educable mentally handicapped (EMH) adolescents. Discussed are the purpose and interpretation of student data for judging a…

Large-Scale Operations Management Test of Use of the White Amur for Control of Problem Aquatic Plants. Report 2. First Year Poststocking Results. Volume VII. A Model for Evaluation of the Response of the Lake Conway, Florida, Ecosystem to Introduction of the White Amur.

DTIC Science & Technology

1981-11-01

OPERATIONS MANAGEMENT S. TYPE OF REPORT A PERIOD COVERED TEST OF THE USE OF THE WHITE AMUR FOR CONTROL OF Report 2 of a series PROBLEM AQUATIC PLANTS...111. 1981. "Large-Scale Operations Management Test of the Use of the White Amur for Control of Problem Aquatic Plants; Report 2, First Year Poststock...Al 3 LARGE-SCALE OPERATIONS MANAGEMENT TEST OF USE OF THE WHITE AMUR FOR CONTROL OF PROBLEM AQUATIC PLANTS A MODEL FOR EVALUATION OF

Criterion Referenced Assessment Bank. Grade 6 Skill Clusters, Objectives, and Illustrations.

ERIC Educational Resources Information Center

Montgomery County Public Schools, Rockville, MD.

Part of a series of competency-based test materials for grades six through ten, this set of nine test booklets for sixth graders contains multiple-choice questions designed to aid in the evaluation of the pupils' library skills. Accompanied by a separate, tenth booklet of illustrations which are to be used in conjunction with the questions, the…

Computerized Classification Testing under the One-Parameter Logistic Response Model with Ability-Based Guessing

ERIC Educational Resources Information Center

Wang, Wen-Chung; Huang, Sheng-Yun

2011-01-01

The one-parameter logistic model with ability-based guessing (1PL-AG) has been recently developed to account for effect of ability on guessing behavior in multiple-choice items. In this study, the authors developed algorithms for computerized classification testing under the 1PL-AG and conducted a series of simulations to evaluate their…

Musical and Verbal Memory in Alzheimer's Disease: A Study of Long-Term and Short-Term Memory

ERIC Educational Resources Information Center

Menard, Marie-Claude; Belleville, Sylvie

2009-01-01

Musical memory was tested in Alzheimer patients and in healthy older adults using long-term and short-term memory tasks. Long-term memory (LTM) was tested with a recognition procedure using unfamiliar melodies. Short-term memory (STM) was evaluated with same/different judgment tasks on short series of notes. Musical memory was compared to verbal…

FIELD CHECK MANUAL FOR LANGUAGE LABORATORIES, A SERIES OF TESTS WHICH A NON-TECHNICAL PERSON CAN CONDUCT TO VERIFY SPECIFICATIONS.

ERIC Educational Resources Information Center

GRITTNER, FRANK; PAVLAT, RUSSELL

IN ORDER TO ASSIST NON-TECHNICAL PEOPLE IN SCHOOLS TO CONDUCT A FIELD CHECK OF LANGUAGE LABORATORY EQUIPMENT BEFORE THEY MAKE FINAL PAYMENTS, THIS MANUAL OFFERS CRITERIA, TESTS, AND METHODS OF SCORING THE QUALITY OF THE EQUIPMENT. CHECKLISTS ARE PROVIDED FOR EVALUATING CONSOLE FUNCTIONS, TAPE RECORDERS, AMPLIFIERS, SOUND QUALITY (INCLUDING…

Aerothermal Protuberance Heating Design and Test Configurations for Ascent Vehicle Design

NASA Technical Reports Server (NTRS)

Martin, Charles E.; Neumann, Richard D.; Freeman, Delma

2010-01-01

A series of tests were conducted to evaluate protuberance heating for the purposes of vehicle design and modification. These tests represent a state of the art approach to both testing and instrumentation for defining aerothermal protuberance effects on the protuberance and surrounding areas. The testing was performed with a number of wind tunnel entries beginning with the proof of concept "pathfinder" test in the Test Section 1 (TS1) tunnel in the Langley Unitary Plan Wind Tunnel (UPWT). The TS1 section (see Figures 1a and 1b) is a lower Mach number tunnel and the Test Section 2 (TS2) has overlapping and higher Mach number capability as showin in Figure 1c. The pathfinder concept was proven and testing proceeded for a series of protuberance tests using an existing splitter aluminum protuberance mounting plate, Macor protuberances, thin film gages, total temperature and pressure gages, Kulite pressure transducers, Infra-Red camera imaging, LASER velocimetry evaluations and the UPWT data collection system. A boundary layer rake was used to identify the boundary layer profile at the protuberance locations for testing and helped protuberance design. This paper discusses the techniques and instrumentation used during the protuberance heating tests performed in the UPWT in TS1 and TS2. Runs of the protuberances were made Mach numbers of 1.5, 2.16, 2.65, and 3.51. The data set generated from this testing is for ascent protuberance effects and is termed Protuberance Heating Ascent Data (PHAD) and this testing may be termed PHAD-1 to distinguish it from future testing of this type.

Extra-Vehicular Activity (EVA) glove evaluation test protocol

NASA Technical Reports Server (NTRS)

Hinman-Sweeney, E. M.

1994-01-01

One of the most critical components of a space suit is the gloves, yet gloves have traditionally presented significant design challenges. With continued efforts at glove development, a method for evaluating glove performance is needed. This paper presents a pressure-glove evaluation protocol. A description of this evaluation protocol, and its development is provided. The protocol allows comparison of one glove design to another, or any one design to bare-handed performance. Gloves for higher pressure suits may be evaluated at current and future design pressures to drive out differences in performance due to pressure effects. Using this protocol, gloves may be evaluated during design to drive out design problems and determine areas for improvement, or fully mature designs may be evaluated with respect to mission requirements. Several different test configurations are presented to handle these cases. This protocol was run on a prototype glove. The prototype was evaluated at two operating pressures and in the unpressurized state, with results compared to bare-handed performance. Results and analysis from this test series are provided, as is a description of the configuration used for this test.

Homogeneity revisited: analysis of updated precipitation series in Turkey

NASA Astrophysics Data System (ADS)

Bickici Arikan, Bugrayhan; Kahya, Ercan

2018-01-01

Homogeneous time series of meteorological variables are necessary for hydrologic and climate studies. Dependability of historical precipitation data is subjected to keen evaluation prior to every study in water resources, hydrology, and climate change fields. This study aims to characterize the homogeneity of long-term Turkish precipitation data in order to ensure that they can be reliably used. The homogeneity of monthly precipitation data set was tested using the standard normal homogeneity test, Buishand test, Von Neumann ratio test, and Pettitt test at the 5% significance level across Turkey. Our precipitation records including the most updated observations, extracted from 160 meteorological stations, for the periods 1974-2014 were analyzed by all the four homogeneity tests. According to the results of all tests, five out of 160 stations have an inhomogeneity. With regard to our strict confirmation rule, 44 out of 160 stations are said to be inhomogeneous since they failed from at least one of the four tests. The breaks captured by the Buishand and Pettitt tests usually tend to appear in the middle of the precipitation series, whereas the ability of standard normal homogeneity test is in favor of identifying inhomogeneities mostly at the beginning or at the end of the records. Our results showed that 42 out of 44 inhomogeneous stations passed all the four tests after applying a correction procedure based on the double mass curve analysis. Available metadata was used to interpret the detected inhomogeneity.

Educational case series: β-lactam allergy and cross-reactivity.

PubMed

Atanasković-Marković, Marina

2011-12-01

Penicillins and cephalosporins are the most widely used antibiotics for the treatment of common infections, and they are the two main classes of β-lactams. On the basis of the time of appearance of the reaction after drug intake and for diagnostic purposes, hypersensitivity reactions to β-lactams have been classified as immediate or non-immediate. The diagnostic evaluation of allergic reactions to β-lactams has changed over the last decade, for several reasons. In many countries, major and minor determinants for skin testing are not available. In immediate allergic reactions, the sensitivity of skin testing is decreasing. For non-immediate reactions, skin testing appears to be less sensitive than previously reported. The drug provocation test is still necessary for diagnosis. In this education review series, we described three cases of β-lactam allergy: first, a child with an IgE-mediated allergy to benzyl-penicillin; second, a child with a non-allergic hypersensitivity to amoxicillin; and in the third patient, we will discuss about cross-reactivity between penicillins and cephalosporins. These cases are correlated with the practical management of evaluating β-lactam allergy. © 2011 John Wiley & Sons A/S.

Torque Tension Testing of Fasteners used for NASA Flight Hardware Applications

NASA Technical Reports Server (NTRS)

Hemminger, Edgar G.; Posey, Alan J.; Dube, Michael J.

2014-01-01

The effect of various lubricants and other compounds on fastener torque-tension relationships is evaluated. Testing was performed using a unique test apparatus developed by Posey at the NASA Goddard Space Flight Center. A description of the test methodology, including associated data collection and analysis will be presented. Test results for 300 series CRES and A286 heat resistant fasteners, torqued into various types of inserts will be presented. The primary objective of this testing was to obtain torque-tension data for use on NASA flight projects.

Cavity Heating Experiments Supporting Shuttle Columbia Accident Investigation

NASA Technical Reports Server (NTRS)

Everhart, Joel L.; Berger, Karen T.; Bey, Kim S.; Merski, N. Ronald; Wood, William A.

2011-01-01

The two-color thermographic phosphor method has been used to map the local heating augmentation of scaled idealized cavities at conditions simulating the windward surface of the Shuttle Orbiter Columbia during flight STS-107. Two experiments initiated in support of the Columbia Accident Investigation were conducted in the Langley 20-Inch Mach 6 Tunnel. Generally, the first test series evaluated open (length-to-depth less than 10) rectangular cavity geometries proposed as possible damage scenarios resulting from foam and ice impact during launch at several discrete locations on the vehicle windward surface, though some closed (length-to-depth greater than 13) geometries were briefly examined. The second test series was designed to parametrically evaluate heating augmentation in closed rectangular cavities. The tests were conducted under laminar cavity entry conditions over a range of local boundary layer edge-flow parameters typical of re-entry. Cavity design parameters were developed using laminar computational predictions, while the experimental boundary layer state conditions were inferred from the heating measurements. An analysis of the aeroheating caused by cavities allowed exclusion of non-breeching damage from the possible loss scenarios being considered during the investigation.

Flight Tests of the Wilford XOZ-1 Sea Gyroplane

NASA Technical Reports Server (NTRS)

Gustafson, Frederic B.

1941-01-01

During August 1939 a series of flight tests was made at Langley Field on the Wilford sea gyroplane, designated by the Navy as the XOZ-1. These tests were intended to permit rough evaluation of the stability and control characteristics of the machine, with particular reference to possible improvements in rigging which might be made in future machines with fixed wing and nonarticulated feathering control rotor, and to provide data on the bending and feathering motions of the rotor blades. The tests made in 1939 proved inadequate, chiefly because the machine as flown did not have sufficient propeller thrust to give it an appreciable speed range in steady flight. Further tests were therefore made in August 1940 after overhauling the engine and substituting a metal propeller for the wooded one first used. The range of speeds covered in steady flight was markedly extended. Steady-flight runs only were made in this series, since it was felt that takeoffs and landings had been covered sufficiently in the previous tests.

Molecular Testing for Targeted Therapy in Advanced Non-Small Cell Lung Cancer: Suitability of Endobronchial Ultrasound Transbronchial Needle Aspiration.

PubMed

Casadio, Chiara; Guarize, Juliana; Donghi, Stefano; Di Tonno, Clementina; Fumagalli, Caterina; Vacirca, Davide; Dell'Orto, Patrizia; De Marinis, Filippo; Spaggiari, Lorenzo; Viale, Giuseppe; Barberis, Massimo

2015-10-01

Endobronchial ultrasound-guided transbronchial needle aspiration (EBUS-TBNA) is a minimally invasive procedure that has revolutionized the diagnosis and staging of lung cancer. The goal of the present study was to investigate the yield and applicability of molecular testing in the specimens obtained by EBUS-TBNA from patients with advanced non-small cell lung cancer (NSCLC), comparing the results with a series of patients who underwent diagnostic surgical procedures in the same institution. The study followed 306 consecutive patients with clinically diagnosed primary lung cancer who had the EBUS-TBNA procedure. EGFR and KRAS mutations were evaluated on cytologic specimens by Sanger sequencing and Cobas real-time polymerase chain reaction, whereas ALK rearrangement was tested by fluorescence in situ hybridization. The results were compared with those obtained from a series of 1,000 NSCLC surgical samples routinely analyzed. Molecular testing was possible in 96.9% of the samples obtained by EBUS-TBNA. EGFR (exons 18-21) mutations were found in 16.9%, KRAS mutation (exons 2-3) in 31.6%, and ALK rearrangement in 3.9% of the cases. In the surgical series, the mutations' distribution were 14.8%, 29.0%, and 3.4%, respectively. There were no statistical differences between the two series. Our study demonstrates that EBUS-TBNA can be effectively used not just for diagnosis but also for complete mutational testing. Copyright© by the American Society for Clinical Pathology.

Aircraft surface coatings

NASA Technical Reports Server (NTRS)

1983-01-01

A series of studies in which films and liquid spray-on materials were evaluated in the laboratory for transport aircraft external surface coatings are summarized. Elastomeric polyurethanes were found to best meet requirements. Two commercially available products, CAAPCO B-274 and Chemglaze M313, were subjected to further laboratory testing, airline service evaluations, and drag-measurement flight tests. It was found that these coatings were compatible with the severe operating environment of airlines and that coatings reduced airplane drag. An economic analysis indicated significant dollar benefits to airlines from application of the coatings.

AGARD Flight Test Techniques Series. Volume 17. Electronic Warfare Test and Evaluation. (Les Essais et l’Evaluation du Materiel de Guerre Electronique)

DTIC Science & Technology

2000-03-01

FRIENDLY DR ENEMY PLOY OFOR DEGSRADING, ENEUTALY IG DEGRA E,’ EUTRALIE, OR DESTR Y concepts, procedures, and techniques that apply generically to CMA...Association of Old Crows, September 1984 Price, Alfred, "The History of Electronic Warfare," Volume 2, Association of Old Crows, October 1989 Claxton, John...Canada Les demandes de documents RTO ou AGARD doivent comporter la denomination "RTO" ou "AGARD" selon le cas, suivie du numdro de s~rie (par exemple

Project FIRES. Volume 1: Program Overview and Summary, Phase 1B

NASA Technical Reports Server (NTRS)

Abeles, F. J.

1980-01-01

Overall performance requirements and evaluation methods for firefighters protective equipment were established and published as the Protective Ensemble Performance Standards (PEPS). Current firefighters protective equipment was tested and evaluated against the PEPS requirements, and the preliminary design of a prototype protective ensemble was performed. In phase 1B, the design of the prototype ensemble was finalized. Prototype ensembles were fabricated and then subjected to a series of qualification tests which were based upon the PEPS requirements. Engineering drawings and purchase specifications were prepared for the new protective ensemble.

Fragmentation of Solid Materials Using Shock Tubes. Part 2: First Test Series in a Large Diameter Shock Tube

DTIC Science & Technology

2017-12-01

description in Figure 9 below 2 Full or partial loss of test data due to instrumentation/triggering failures 3 Gages not included in these tests 4...Table 2. Sample properties. Test Description Dimensions Weight (lbs.) Strength (psi) Notes 17 Fully Tempered Glass Window 4-ft x 6-ft x...an estimate of prism strength for medium weight CMU. The reinforced concrete sample was a 5.5-in thick solid panel. To evaluate its strength

Evaluation of new spectral bands for multi-spectral imaging: SMIRR aircraft test results

USGS Publications Warehouse

Goetz, Alexander F.H.; Rowan, Lawrence C.; Barringer, Anthony R.

1980-01-01

A 10-channel radiometer called the Shuttle Multispectral Infrared Radiometer (SMIRR) is scheduled to take data from orbit on the second shuttle orbital light test. As part of the instrument test sequence, a series of aircraft flights was carried out over 10 test areas in Utah and Nevada. Apart from vegetation, the materials exposed at the surface were volcanic sequences ranging from tuffs to basalts, areas of hydrothermally altered volcanic rocks, sedimentary sequences of sandstone and carbonate rocks, and alluvial cover.

Vibration effects of the space shuttle main engine high pressure oxidizer turbopump bellows

NASA Technical Reports Server (NTRS)

Harp, J. A.

1978-01-01

A welded metal bellows was subjected to a series of vibration tests in a 400 psi oxygen environment to evaluate the effects of the bellows convolutes rubbing on the damper ring in the high pressure oxidizer turbopump of the space shuttle main engine. The bellows was subjected to approximately 2 million cycles at 0.007 in. double amplitude displacement during this series of tests, at a frequency of 400 Hz. Intrumentation of the test specimen revealed no significant heat buildup caused by the rubbing of the bellows convolutes on the damper ring. A final destruct test was made to determine if a fire would result if the bellows ruptured in the 400 psi oxygen environment, thus exposing a fresh metal surface. The vibration input was changed to 0.8 in. double amplitude displacement at 20 Hz to intentionally rupture the bellows. Failure occurred after 2.5 sec; no fire or heat buildup was encountered.

Enhancing causal interpretations of quality improvement interventions

PubMed Central

Cable, G

2001-01-01

In an era of chronic resource scarcity it is critical that quality improvement professionals have confidence that their project activities cause measured change. A commonly used research design, the single group pre-test/post-test design, provides little insight into whether quality improvement interventions cause measured outcomes. A re-evaluation of a quality improvement programme designed to reduce the percentage of bilateral cardiac catheterisations for the period from January 1991 to October 1996 in three catheterisation laboratories in a north eastern state in the USA was performed using an interrupted time series design with switching replications. The accuracy and causal interpretability of the findings were considerably improved compared with the original evaluation design. Moreover, the re-evaluation provided tangible evidence in support of the suggestion that more rigorous designs can and should be more widely employed to improve the causal interpretability of quality improvement efforts. Evaluation designs for quality improvement projects should be constructed to provide a reasonable opportunity, given available time and resources, for causal interpretation of the results. Evaluators of quality improvement initiatives may infrequently have access to randomised designs. Nonetheless, as shown here, other very rigorous research designs are available for improving causal interpretability. Unilateral methodological surrender need not be the only alternative to randomised experiments. Key Words: causal interpretations; quality improvement; interrupted time series design; implementation fidelity PMID:11533426

Electrostatic Evaluation of the Propellant Handlers Ensemble

NASA Technical Reports Server (NTRS)

Hogue, Michael D.; Calle, Carlos I.; Buhler, Charles

2006-01-01

The Self-Contained Atmospheric Protective Ensemble (SCAPE) used in propellant handling at NASA's Kennedy Space Center (KSC) has recently completed a series of tests to determine its electrostatic properties of the coverall fabric used in the Propellant Handlers Ensemble (PHE). Understanding these electrostatic properties are fundamental to ensuring safe operations when working with flammable rocket propellants such as hydrazine, methyl hydrazine, and unsymmetrical dimethyl hydrazine. These tests include surface resistivity, charge decay, triboelectric charging, and flame incendivity. In this presentation, we will discuss the results of these tests on the current PHE as well as new fabrics and materials being evaluated for the next generation of PHE.

Surface-specific additive manufacturing test artefacts

NASA Astrophysics Data System (ADS)

Townsend, Andrew; Racasan, Radu; Blunt, Liam

2018-06-01

Many test artefact designs have been proposed for use with additive manufacturing (AM) systems. These test artefacts have primarily been designed for the evaluation of AM form and dimensional performance. A series of surface-specific measurement test artefacts designed for use in the verification of AM manufacturing processes are proposed here. Surface-specific test artefacts can be made more compact because they do not require the large dimensions needed for accurate dimensional and form measurements. The series of three test artefacts are designed to provide comprehensive information pertaining to the manufactured surface. Measurement possibilities include deviation analysis, surface texture parameter data generation, sub-surface analysis, layer step analysis and build resolution comparison. The test artefacts are designed to provide easy access for measurement using conventional surface measurement techniques, for example, focus variation microscopy, stylus profilometry, confocal microscopy and scanning electron microscopy. Additionally, the test artefacts may be simply visually inspected as a comparative tool, giving a fast indication of process variation between builds. The three test artefacts are small enough to be included in every build and include built-in manufacturing traceability information, making them a convenient physical record of the build.

Historical Data Analysis of Hospital Discharges Related to the Amerithrax Attack in Florida

PubMed Central

Burke, Lauralyn K.; Brown, C. Perry; Johnson, Tammie M.

2016-01-01

Interrupted time-series analysis (ITSA) can be used to identify, quantify, and evaluate the magnitude and direction of an event on the basis of time-series data. This study evaluates the impact of the bioterrorist anthrax attacks (“Amerithrax”) on hospital inpatient discharges in the metropolitan statistical area of Palm Beach, Broward, and Miami-Dade counties in the fourth quarter of 2001. Three statistical methods—standardized incidence ratio (SIR), segmented regression, and an autoregressive integrated moving average (ARIMA)—were used to determine whether Amerithrax influenced inpatient utilization. The SIR found a non–statistically significant 2 percent decrease in hospital discharges. Although the segmented regression test found a slight increase in the discharge rate during the fourth quarter, it was also not statistically significant; therefore, it could not be attributed to Amerithrax. Segmented regression diagnostics preparing for ARIMA indicated that the quarterly data time frame was not serially correlated and violated one of the assumptions for the use of the ARIMA method and therefore could not properly evaluate the impact on the time-series data. Lack of data granularity of the time frames hindered the successful evaluation of the impact by the three analytic methods. This study demonstrates that the granularity of the data points is as important as the number of data points in a time series. ITSA is important for the ability to evaluate the impact that any hazard may have on inpatient utilization. Knowledge of hospital utilization patterns during disasters offer healthcare and civic professionals valuable information to plan, respond, mitigate, and evaluate any outcomes stemming from biothreats. PMID:27843420

Tracking variable sedimentation rates in orbitally forced paleoclimate proxy series

NASA Astrophysics Data System (ADS)

Li, M.; Kump, L. R.; Hinnov, L.

2017-12-01

This study addresses two fundamental issues in cyclostratigraphy: quantitative testing of orbital forcing in cyclic sedimentary sequences and tracking variable sedimentation rates. The methodology proposed here addresses these issues as an inverse problem, and estimates the product-moment correlation coefficient between the frequency spectra of orbital solutions and paleoclimate proxy series over a range of "test" sedimentation rates. It is inspired by the ASM method (1). The number of orbital parameters involved in the estimation is also considered. The method relies on the hypothesis that orbital forcing had a significant impact on the paleoclimate proxy variations, and thus is also tested. The null hypothesis of no astronomical forcing is evaluated using the Beta distribution, for which the shape parameters are estimated using a Monte Carlo simulation approach. We introduce a metric to estimate the most likely sedimentation rate using the product-moment correlation coefficient, H0 significance level, and the number of contributing orbital parameters, i.e., the CHO value. The CHO metric is applied with a sliding window to track variable sedimentation rates along the paleoclimate proxy series. Two forward models with uniform and variable sedimentation rates are evaluated to demonstrate the robustness of the method. The CHO method is applied to the classical Late Triassic Newark depth rank series; the estimated sedimentation rates match closely with previously published sedimentation rates and provide a more highly time-resolved estimate (2,3). References: (1) Meyers, S.R., Sageman, B.B., Amer. J. Sci., 307, 773-792, 2007; (2) Kent, D.V., Olsen, P.E., Muttoni, G., Earth-Sci. Rev.166, 153-180, 2017; (3) Li, M., Zhang, Y., Huang, C., Ogg, J., Hinnov, L., Wang, Y., Zou, Z., Li, L., 2017. Earth Plant. Sc. Lett. doi:10.1016/j.epsl.2017.07.015

AMENDMENT OF SEDIMENTS WITH A CARBONACEOUS RESIN REDUCES BIOAVAILABILITY OF POLYCYCLIC AROMATIC HYDROCARBONS

EPA Science Inventory

A series of laboratory and field test studies were conducted to evaluate the effectiveness of Ambersorb, a carbonaceous resin, in reducing bioavailability of polycyclic aromatic hydrocarbons (PAHs) in contaminated sediments collected from the field. Amending contaminated sediment...

Los Angeles congestion reduction demonstration (Metro ExpressLanes) program. National evaluation : exogenous factors test plan.

DOT National Transportation Integrated Search

1999-12-01

The Traceability document consists of brief introductory material and a series of appended Trace Tables. These tables provide complete traceability of ITS User Service Requirements (USR) to elements of the National ITS Architecture. Additional Trace ...

Los Angeles congestion reduction demonstration (Metro ExpressLanes). National evaluation : cost benefit analysis test plan.

DOT National Transportation Integrated Search

2002-04-01

The Theory of Operations document is one of a series of deliverables documenting the National Intelligent Transportation System (ITS) Architecture developed under contract to the U.S. Department of Transportation (DOT). The Theory of Operations Docum...

BIODEGRADATION OF AROMATIC HYDROCARBONS BY AQUIFER MICROORGANISMS UNDER DENITRIFYING CONDITIONS

EPA Science Inventory

A series of laboratory tests were conducted to evaluate whether denitrification would be a suitable alternative for biorestoration of an aquifer contaminated with JP-4 jet fuel. Microcosms were prepared from both uncontaminated and contaminated-aquifer material from the site, in ...

TRACER DISPERSION STUDIES FOR HYDRAULIC CHARACTERIZATION OF PIPES

EPA Science Inventory

A series of experiments were conducted at the U. S. Environmental Protection Agency (EPA) Test & Evaluation (T&E) Facility in Cincinnati, Ohio, to quantify longitudinal dispersion of a sodium fluoride tracer in polyvinyl chloride (PVC) pipe and ductile iron pipe under laminar, tr...

Automated Test Methods for XML Metadata

DTIC Science & Technology

2017-12-28

Group under RCC Task TG-147. This document (Volume VI of the RCC Document 118 series) describes procedures used for evaluating XML metadata documents...including TMATS, MDL, IHAL, and DDML documents. These documents contain specifications or descriptions of artifacts and systems of importance to...the collection and management of telemetry data. The methods defined in this report provide a means of evaluating the suitability of such a metadata

Synthesis and biological evaluation of novel dioxa-bicycle C-aryl glucosides as SGLT2 inhibitors.

PubMed

Yan, Qi; Ding, Ning; Li, Yingxia

2016-02-08

A series of novel C-aryl glucosides containing dioxa-bicycle were synthesized and evaluated for inhibition activity against hSGLT2. Among the compounds tested, compound 6a showed moderate SGLT2 inhibition activities at 700 nM. The results could benefit the discovery of new SGLT2 inhibitors. Copyright © 2015 Elsevier Ltd. All rights reserved.

Space Station-based deep-space optical communication experiments

NASA Technical Reports Server (NTRS)

Chen, Chien-Chung; Schwartz, Jon A.

1988-01-01

A series of three experiments proposed for advanced optical deep-space communications is described. These proposed experiments would be carried out aboard the Space Station to test and evaluate the capability of optical instruments to conduct data communication and spacecraft navigation for deep-space missions. Techniques for effective data communication, precision spacecraft ranging, and accurate angular measurements will be developed and evaluated in a spaceborne environment.

Evaluating the efficacy of wood shreds for mitigating erosion

Treesearch

Randy B. Foltz; Natalie S. Copeland

2009-01-01

An erosion control product made by shredding on-site woody materials was evaluated for mitigating erosion through a series of rainfall simulations. Tests were conducted on bare soil and soil with 30, 50, and 70% cover on a coarse and a fine-grained soil. Results indicated that the wood product known as wood shreds reduced runoff and soil loss from both soil types....

Positive concomitant test reactions to allergens in the standard patch test series.

PubMed

Landeck, Lilla; González, Ernesto; Baden, Lynn; Neumann, Konrad; Schalock, Peter

2010-05-01

Patch testing is performed to evaluate suspected allergic contact dermatitis. Common wisdom suggests that various allergens cross-react but only a few larger studies have published confirmations of this. The purpose of our study was to identify significant correlations between positive test reactions in a screening series. A total of 1235 patients undergoing patch testing to the Hermal standard series at the Massachusetts General Hospital, Contact Dermatitis Clinic between 1990 and 2006 were investigated. Two or more positive reactions were seen in 411 patients (33.3%). Sensitizations to eight pairs of allergens were found to have significant correlation (P

Evaluation of Acoustic Emission SHM of PRSEUS Composite Pressure Cube Tests

NASA Technical Reports Server (NTRS)

Horne, Michael R.; Madaras, Eric I.

2013-01-01

A series of tests of the Pultruded Rod Stitched Efficient Unitized Structure (PRSEUS) pressure cube were conducted during third quarter 2011 at NASA Langley Research Center (LaRC) in the Combined Loads Test facility (COLTS). This is a report of the analysis of the Acoustic Emission (AE) data collected during those tests. The AE signals of the later tests are consistent with the final failure progression through two of the pressure cube panels. Calibration tests and damage precursor AE indications, from preliminary checkout pressurizations, indicated areas of concern that eventually failed. Hence those tests have potential for vehicle health monitoring.

Demonstration of Robustness and Integrated Operation of a Series-Bosch System

NASA Technical Reports Server (NTRS)

Abney, Morgan B.; Mansell, Matthew J.; Stanley, Christine; Barnett, Bill; Junaedi, Christian; Vilekar, Saurabh A.; Ryan, Kent

2016-01-01

Manned missions beyond low Earth orbit will require highly robust, reliable, and maintainable life support systems that maximize recycling of water and oxygen. Bosch technology is one option to maximize oxygen recovery, in the form of water, from metabolically-produced carbon dioxide (CO2). A two stage approach to Bosch, called Series-Bosch, reduces metabolic CO2 with hydrogen (H2) to produce water and solid carbon using two reactors: a Reverse Water-Gas Shift (RWGS) reactor and a carbon formation (CF) reactor. Previous development efforts demonstrated the stand-alone performance of a NASA-designed RWGS reactor designed for robustness against carbon formation, two membrane separators intended to maximize single pass conversion of reactants, and a batch CF reactor with both transit and surface catalysts. In the past year, Precision Combustion, Inc. (PCI) developed and delivered a RWGS reactor for testing at NASA. The reactor design was based on their patented Microlith® technology and was first evaluated under a Phase I Small Business Innovative Research (SBIR) effort in 2010. The RWGS reactor was recently evaluated at NASA to compare its performance and operating conditions with NASA's RWGS reactor. The test results will be provided in this paper. Separately, in 2015, a semi-continuous CF reactor was designed and fabricated at NASA based on the results from batch CF reactor testing. The batch CF reactor and the semi-continuous CF reactor were individually integrated with an upstream RWGS reactor to demonstrate the system operation and to evaluate performance. Here, we compare the performance and robustness to carbon formation of both RWGS reactors. We report the results of the integrated operation of a Series-Bosch system and we discuss the technology readiness level.

A Classical Test Theory Analysis of the Light and Spectroscopy Concept Inventory National Study Data Set

ERIC Educational Resources Information Center

Schlingman, Wayne M.; Prather, Edward E.; Wallace, Colin S.; Brissenden, Gina; Rudolph, Alexander L.

2012-01-01

This paper is the first in a series of investigations into the data from the recent national study using the Light and Spectroscopy Concept Inventory (LSCI). In this paper, we use classical test theory to form a framework of results that will be used to evaluate individual item difficulties, item discriminations, and the overall reliability of the…

Use of Saliva for Assessment of Stress and Its Effect on the Immune System Prior to Gross Anatomy Practical Examinations

ERIC Educational Resources Information Center

Lester, S. Reid; Brown, Jason R.; Aycock, Jeffrey E.; Grubbs, S. Lee; Johnson, Roger B.

2010-01-01

The objective of this study was to determine the longitudinal effects of a series of stressful gross anatomy tests on the immune system. Thirty-six freshman occupational therapy students completed a written stress evaluation survey, and saliva samples were obtained at baseline and prior to each of three timed-practical gross anatomy tests.…

Synthesis and antibacterial activity of aromatic and heteroaromatic amino alcohols.

PubMed

de Almeida, Camila G; Reis, Samira G; de Almeida, Angelina M; Diniz, Claudio G; da Silva, Vânia L; Le Hyaric, Mireille

2011-11-01

Two series of aromatic and heteroaromatic amino alcohols were synthesized from alcohols and aldehydes and evaluated for their antibacterial activities. All the octylated compounds displayed a better activity against the four bacteria tested when evaluated by the agar diffusion method and were selected for the evaluation of minimal inhibitory concentration. The best results were obtained for p-octyloxybenzyl derivatives against Staphylococcus epidermidis (minimal inhibitory concentrations = 32 μm). © 2011 John Wiley & Sons A/S.

Clinical time series prediction: Toward a hierarchical dynamical system framework.

PubMed

Liu, Zitao; Hauskrecht, Milos

2015-09-01

Developing machine learning and data mining algorithms for building temporal models of clinical time series is important for understanding of the patient condition, the dynamics of a disease, effect of various patient management interventions and clinical decision making. In this work, we propose and develop a novel hierarchical framework for modeling clinical time series data of varied length and with irregularly sampled observations. Our hierarchical dynamical system framework for modeling clinical time series combines advantages of the two temporal modeling approaches: the linear dynamical system and the Gaussian process. We model the irregularly sampled clinical time series by using multiple Gaussian process sequences in the lower level of our hierarchical framework and capture the transitions between Gaussian processes by utilizing the linear dynamical system. The experiments are conducted on the complete blood count (CBC) panel data of 1000 post-surgical cardiac patients during their hospitalization. Our framework is evaluated and compared to multiple baseline approaches in terms of the mean absolute prediction error and the absolute percentage error. We tested our framework by first learning the time series model from data for the patients in the training set, and then using it to predict future time series values for the patients in the test set. We show that our model outperforms multiple existing models in terms of its predictive accuracy. Our method achieved a 3.13% average prediction accuracy improvement on ten CBC lab time series when it was compared against the best performing baseline. A 5.25% average accuracy improvement was observed when only short-term predictions were considered. A new hierarchical dynamical system framework that lets us model irregularly sampled time series data is a promising new direction for modeling clinical time series and for improving their predictive performance. Copyright © 2014 Elsevier B.V. All rights reserved.

Comparison of solid-phase and pore-water approaches for assessing the quality of marine and estuarine sediments

USGS Publications Warehouse

Carr, Robert Scott; Chapman, Duane C.

1992-01-01

As part of our continuing evaluation of the pore-water approach for assessing sediment quality, we made a series of side-by-side comparisons between the standard 10-day amphipod whole sediment test with the corophiid Grandidierella japonica and a suite of tests using pore water extracted from the same sediments. the pore-water tests evaluated were the sea urchin (Arbacia punctulata) sperm cell test and morphological development assay, the life-cycle test with the polychaete Dinophilus gyrociliatus, and acute exposures of red drum (Sciaenops ocellatus) embryo-larval stages. Sediment and surface microlayer samples were collected from contaminated sites. Whole-sediment, pore-water, and surface microlayer toxicity tests were performed. Pore-water toxicity tests were considerably more sensitive than the whole-sediment amphipod test, which is currently the most sensitive toxicity test now recommended for determining the acceptability of dredged material for open ocean disposal.

An evaluation of grease type ball bearing lubricants operating in various environments

NASA Technical Reports Server (NTRS)

Mcmurtrey, E. L.

1981-01-01

Because many future spacecraft or space stations will require mechanisms to operate for long periods of time in environments which are adverse to most bearing lubricants, a series of tests is continuing to evaluate 38 grease type lubricants in R-4 size bearings in five different environments for a 1 year period. Four repetitions of each test are made to provide statistical samples. These tests were used to select four lubricants for 5 year tests in selected environments with five repetitions of each test for statistical samples. At the present time, 100 test sets are completed and 22 test sets are underway. Three 5 year tests were started in (1) continuous operation and (2) start-stop operation, with both in vacuum at ambient temperatures, and (3) continuous operation at 93.3 C. In the 1 year tests the best results to date in all environments were obtained with a high viscosity index perfluoroalkylpolyether (PFPE) grease.

Detection of nuclear testing from surface concentration measurements: Analysis of radioxenon from the February 2013 underground test in North Korea

DOE PAGES

Kurzeja, R. J.; Buckley, R. L.; Werth, D. W.; ...

2017-12-28

A method is outlined and tested to detect low level nuclear or chemical sources from time series of concentration measurements. The method uses a mesoscale atmospheric model to simulate the concentration signature from a known or suspected source at a receptor which is then regressed successively against segments of the measurement series to create time series of metrics that measure the goodness of fit between the signatures and the measurement segments. The method was applied to radioxenon data from the Comprehensive Test Ban Treaty (CTBT) collection site in Ussuriysk, Russia (RN58) after the Democratic People's Republic of Korea (North Korea)more » underground nuclear test on February 12, 2013 near Punggye. The metrics were found to be a good screening tool to locate data segments with a strong likelihood of origin from Punggye, especially when multiplied together to a determine the joint probability. Metrics from RN58 were also used to find the probability that activity measured in February and April of 2013 originated from the Feb 12 test. A detailed analysis of an RN58 data segment from April 3/4, 2013 was also carried out for a grid of source locations around Punggye and identified Punggye as the most likely point of origin. Thus, the results support the strong possibility that radioxenon was emitted from the test site at various times in April and was detected intermittently at RN58, depending on the wind direction. The method does not locate unsuspected sources, but instead, evaluates the probability of a source at a specified location. However, it can be extended to include a set of suspected sources. Extension of the method to higher resolution data sets, arbitrary sampling, and time-varying sources is discussed along with a path to evaluate uncertainty in the calculated probabilities.« less

Detection of nuclear testing from surface concentration measurements: Analysis of radioxenon from the February 2013 underground test in North Korea

NASA Astrophysics Data System (ADS)

Kurzeja, R. J.; Buckley, R. L.; Werth, D. W.; Chiswell, S. R.

2018-03-01

A method is outlined and tested to detect low level nuclear or chemical sources from time series of concentration measurements. The method uses a mesoscale atmospheric model to simulate the concentration signature from a known or suspected source at a receptor which is then regressed successively against segments of the measurement series to create time series of metrics that measure the goodness of fit between the signatures and the measurement segments. The method was applied to radioxenon data from the Comprehensive Test Ban Treaty (CTBT) collection site in Ussuriysk, Russia (RN58) after the Democratic People's Republic of Korea (North Korea) underground nuclear test on February 12, 2013 near Punggye. The metrics were found to be a good screening tool to locate data segments with a strong likelihood of origin from Punggye, especially when multiplied together to a determine the joint probability. Metrics from RN58 were also used to find the probability that activity measured in February and April of 2013 originated from the Feb 12 test. A detailed analysis of an RN58 data segment from April 3/4, 2013 was also carried out for a grid of source locations around Punggye and identified Punggye as the most likely point of origin. Thus, the results support the strong possibility that radioxenon was emitted from the test site at various times in April and was detected intermittently at RN58, depending on the wind direction. The method does not locate unsuspected sources, but instead, evaluates the probability of a source at a specified location. However, it can be extended to include a set of suspected sources. Extension of the method to higher resolution data sets, arbitrary sampling, and time-varying sources is discussed along with a path to evaluate uncertainty in the calculated probabilities.

Detection of nuclear testing from surface concentration measurements: Analysis of radioxenon from the February 2013 underground test in North Korea

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kurzeja, R. J.; Buckley, R. L.; Werth, D. W.

A method is outlined and tested to detect low level nuclear or chemical sources from time series of concentration measurements. The method uses a mesoscale atmospheric model to simulate the concentration signature from a known or suspected source at a receptor which is then regressed successively against segments of the measurement series to create time series of metrics that measure the goodness of fit between the signatures and the measurement segments. The method was applied to radioxenon data from the Comprehensive Test Ban Treaty (CTBT) collection site in Ussuriysk, Russia (RN58) after the Democratic People's Republic of Korea (North Korea)more » underground nuclear test on February 12, 2013 near Punggye. The metrics were found to be a good screening tool to locate data segments with a strong likelihood of origin from Punggye, especially when multiplied together to a determine the joint probability. Metrics from RN58 were also used to find the probability that activity measured in February and April of 2013 originated from the Feb 12 test. A detailed analysis of an RN58 data segment from April 3/4, 2013 was also carried out for a grid of source locations around Punggye and identified Punggye as the most likely point of origin. Thus, the results support the strong possibility that radioxenon was emitted from the test site at various times in April and was detected intermittently at RN58, depending on the wind direction. The method does not locate unsuspected sources, but instead, evaluates the probability of a source at a specified location. However, it can be extended to include a set of suspected sources. Extension of the method to higher resolution data sets, arbitrary sampling, and time-varying sources is discussed along with a path to evaluate uncertainty in the calculated probabilities.« less

Fuzzy logic based sensor performance evaluation of vehicle mounted metal detector systems

NASA Astrophysics Data System (ADS)

Abeynayake, Canicious; Tran, Minh D.

2015-05-01

Vehicle Mounted Metal Detector (VMMD) systems are widely used for detection of threat objects in humanitarian demining and military route clearance scenarios. Due to the diverse nature of such operational conditions, operational use of VMMD without a proper understanding of its capability boundaries may lead to heavy causalities. Multi-criteria fitness evaluations are crucial for determining capability boundaries of any sensor-based demining equipment. Evaluation of sensor based military equipment is a multi-disciplinary topic combining the efforts of researchers, operators, managers and commanders having different professional backgrounds and knowledge profiles. Information acquired through field tests usually involves uncertainty, vagueness and imprecision due to variations in test and evaluation conditions during a single test or series of tests. This report presents a fuzzy logic based methodology for experimental data analysis and performance evaluation of VMMD. This data evaluation methodology has been developed to evaluate sensor performance by consolidating expert knowledge with experimental data. A case study is presented by implementing the proposed data analysis framework in a VMMD evaluation scenario. The results of this analysis confirm accuracy, practicability and reliability of the fuzzy logic based sensor performance evaluation framework.

Using Multi-Objective Genetic Programming to Synthesize Stochastic Processes

NASA Astrophysics Data System (ADS)

Ross, Brian; Imada, Janine

Genetic programming is used to automatically construct stochastic processes written in the stochastic π-calculus. Grammar-guided genetic programming constrains search to useful process algebra structures. The time-series behaviour of a target process is denoted with a suitable selection of statistical feature tests. Feature tests can permit complex process behaviours to be effectively evaluated. However, they must be selected with care, in order to accurately characterize the desired process behaviour. Multi-objective evaluation is shown to be appropriate for this application, since it permits heterogeneous statistical feature tests to reside as independent objectives. Multiple undominated solutions can be saved and evaluated after a run, for determination of those that are most appropriate. Since there can be a vast number of candidate solutions, however, strategies for filtering and analyzing this set are required.

General purpose free floating platform for KC-135 flight experimentation

NASA Technical Reports Server (NTRS)

Borchers, Bruce A.; Yendler, Boris S.; Kliss, Mark H.; Gonzales, Andrew A.; Edwards, Mark T.

1994-01-01

The Controlled Ecological Life Support Systems (CELSS) program is evaluating higher plants as a means of providing life support functions aboard space craft. These plant systems will be capable of regenerating air and water while meeting some of the food requirements of the crew. In order to grow plants in space, a series of systems are required to provide the necessary plant support functions. Some of the systems required for CELSS experiments are such that is is likely that existing technologies will require refinement, or novel technologies will need to be developed. To evaluate and test these technologies, a series of KC-135 precursor flights are being proposed. A general purpose free floating experiment platform is being developed to allow the KC-135 flights to be used to their fullest. This paper will outline the basic design for the CELSS Free Floating Test Bed (FFTB), and the requirements for the individual subsystems. Several preliminary experiments suitable for the free floater will also be discussed.

Synthesis and Evaluation of Novel Oxyalkylated Derivatives of 2′,4′-Dihydroxychalcone as Anti-Oomycete Agents against Bronopol Resistant Strains of Saprolegnia sp.

PubMed Central

Flores, Susana; Montenegro, Iván; Villena, Joan; Cuellar, Mauricio; Werner, Enrique; Godoy, Patricio; Madrid, Alejandro

2016-01-01

A series of novel oxyalkylchalcones substituted with alkyl groups were designed and synthesized, and the antioomycete activity of the series was evaluated in vitro against Saprolegnia strains. All tested O-alkylchalcones were synthesized by means of nucleophilic substitution from the natural compound 2′,4′-dihydroxychalcone (1) and the respective alkyl bromide. The natural chalcone (1) and 10 synthetic oxyalkylchalcones (2–11) were tested against Saprolegnia parasitica and Saprolegnia australis. Among synthetic analogs, 2-hydroxy,4-farnesyloxychalcone (11) showed the most potent activity against Saprolegnia sp., with MIC and MOC values of 125 µg/mL (similar to bronopol at 150 µg/mL) and 175 µg/mL, respectively; however, 2′,4′-dihydroxychalcone (1) was the strongest and most active molecule, with MIC and MOC values of 6.25 µg/mL and 12.5 µg/mL. PMID:27556457

Effect of chewing gums on the production of volatile sulfur compounds (VSC) in vivo.

PubMed

Rösing, Cassiano K; Gomes, Sabrina C; Bassani, Diego G; Oppermann, Rui V

2009-01-01

The aim of the present study was to evaluate the effect of two chewing gums on the production of volatile sulfur-containing compounds (VSC) in vivo. Fourteen periodontally healthy participants (20-35 years old) were included in the test panel. Test gum 1 (TG1) contained sucrose and Test gum 2 (TG2) contained xylitol and zinc citrate. Two series of tests were conducted with a double-blind cross-over design. Following an overnight refrain from oral hygiene, VSC was measured before and at 5, 15, 30, 45 and 60 minutes of chewing the test gums. In the second series, VSC production was monitored prior to and up to 30 minutes after a rinse with cysteine 6 mM alone or after a rinse followed by chewing the test gums. For the first test, the results were analyzed by repeated measurements ANOVA for intra-group and paired sample t test for intergroup comparisons. In the second series, percent reduction of VSC was compared by Friedman and Wilcoxon tests (p < .05). The test gums did not differ in terms of VSC production, with values ranging from 146 ppb after 5 minutes to 86 ppb after 60 minutes. Similar reductions in VSC production following cysteine were observed for both test gums, with the largest reductions (71% to 52%) observed after 5 and 15 minutes. It can be concluded that VSC production is diminished after chewing gum and that the use of chewing gums reduces temporarily the VSC production enhanced by cysteine rinses.

Initial Performance Evaluation of Optical Fibers and Sensors Under High-Energy Electron Beam Irradiation

NASA Astrophysics Data System (ADS)

Palmer, Matthew E.; Slusher, David; Fielder, Robert S.

2006-01-01

In this paper, recent work on the performance of optical fiber, fiber optic sensors, and fiber optic connectors under the influence of a high-energy electron beam is presented. Electron beam irradiation is relevant for the Jupiter Icy Moons Orbiter (JIMO) mission due to the high electron radiation environment surrounding Jupiter. As an initial feasibility test, selected optical fiber components were exposed to dose levels relevant to the Jupiter environment. Three separate fiber types were used: one series consisted of pure silica core fiber, two other series consisted of different levels of Germania-doped fiber. Additionally, a series of fused silica Extrinsic Fabry-Perot Interferometer (EFPI)-based fiber optic sensors and two different types of fiber optic connectors were tested. Two types of fiber coatings were evaluated: acrylate and polyimide. All samples were exposed to three different dose levels: 2 MRad, 20 MRad, and 50 MRad. Optical loss measurements were made on the optical fiber spools as a function of wavelength between 750 and 1750nm at periodic intervals up to 75 hrs after exposure. Attenuation is minimal and wavelength-dependent. Fiber optic sensors were evaluated using a standard EFPI sensor readout and diagnostic system. Optical connectors and optical fiber coatings were visually inspected for degradation. Additionally, tensile testing and minimum bend radius testing was conducted on the fibers. Initial loss measurements indicate a low-level of induced optical attenuation in the fiber which recovers with time. The fiber optic sensors exhibited no observable degradation after exposure. The optical fiber connectors and coatings also showed no observable degradation. In addition to harsh environment survivability, fiber optic sensors offer a number of intrinsic advantages for space nuclear power applications including extremely low mass, immunity to electromagnetic interference, self diagnostics / prognostics, and smart sensor capability. Deploying fiber optic sensors on future space exploration missions would provide a substantial improvement in spacecraft instrumentation.

Comprehensive evaluation of the child with intellectual disability or global developmental delays.

PubMed

Moeschler, John B; Shevell, Michael

2014-09-01

Global developmental delay and intellectual disability are relatively common pediatric conditions. This report describes the recommended clinical genetics diagnostic approach. The report is based on a review of published reports, most consisting of medium to large case series of diagnostic tests used, and the proportion of those that led to a diagnosis in such patients. Chromosome microarray is designated as a first-line test and replaces the standard karyotype and fluorescent in situ hybridization subtelomere tests for the child with intellectual disability of unknown etiology. Fragile X testing remains an important first-line test. The importance of considering testing for inborn errors of metabolism in this population is supported by a recent systematic review of the literature and several case series recently published. The role of brain MRI remains important in certain patients. There is also a discussion of the emerging literature on the use of whole-exome sequencing as a diagnostic test in this population. Finally, the importance of intentional comanagement among families, the medical home, and the clinical genetics specialty clinic is discussed. Copyright © 2014 by the American Academy of Pediatrics.

Induced static asymmetry of the pelvis is associated with functional asymmetry of the lumbo-pelvo-hip complex.

PubMed

Gnat, Rafał; Saulicz, Edward

2008-03-01

This study evaluates the hypothesis that triggering and eliminating induced static pelvic asymmetry (SPA) may be followed by immediate change in functional asymmetry of the lumbo-pelvo-hip complex. Repeated measures experimental design with 2 levels of independent variable, that is, induced SPA triggered and induced SPA eliminated, was implemented. Three series of measurements were performed, that is, baseline, after triggering SPA, and after eliminating SPA. A group of 84 subjects with no initial symptoms of SPA was studied. Different forms of mechanical stimulation were applied aiming to induce SPA, and the 2 manual stretching-manipulating techniques were performed aiming to eliminate it. A hand inclinometer was used to measure SPA in standing posture. Selected ranges of motion of the hip joints and lumbar spine were used to depict functional asymmetry of the lumbo-pelvo-hip complex. The functional asymmetry indices for individual movements were calculated. Repeated measures design of analysis of variance, dependent data Student t test, and linear Pearson's correlation test were used. Assessment of the SPA showed its significant increase between baseline and series 2 measurements, with a subsequent significant decrease between series 2 and series 3 measurements. Values of the functional asymmetry indices changed accordingly, that is, they increased significantly between series 1 and series 2 and had returned to their initial level in series 3 measurements. Induced SPA shows considerable association with functional asymmetry of the lumbo-pelvo-hip complex.

Classification of biosensor time series using dynamic time warping: applications in screening cancer cells with characteristic biomarkers.

PubMed

Rai, Shesh N; Trainor, Patrick J; Khosravi, Farhad; Kloecker, Goetz; Panchapakesan, Balaji

2016-01-01

The development of biosensors that produce time series data will facilitate improvements in biomedical diagnostics and in personalized medicine. The time series produced by these devices often contains characteristic features arising from biochemical interactions between the sample and the sensor. To use such characteristic features for determining sample class, similarity-based classifiers can be utilized. However, the construction of such classifiers is complicated by the variability in the time domains of such series that renders the traditional distance metrics such as Euclidean distance ineffective in distinguishing between biological variance and time domain variance. The dynamic time warping (DTW) algorithm is a sequence alignment algorithm that can be used to align two or more series to facilitate quantifying similarity. In this article, we evaluated the performance of DTW distance-based similarity classifiers for classifying time series that mimics electrical signals produced by nanotube biosensors. Simulation studies demonstrated the positive performance of such classifiers in discriminating between time series containing characteristic features that are obscured by noise in the intensity and time domains. We then applied a DTW distance-based k -nearest neighbors classifier to distinguish the presence/absence of mesenchymal biomarker in cancer cells in buffy coats in a blinded test. Using a train-test approach, we find that the classifier had high sensitivity (90.9%) and specificity (81.8%) in differentiating between EpCAM-positive MCF7 cells spiked in buffy coats and those in plain buffy coats.

Further important sensitizers in patients sensitive to fragrances.

PubMed

Frosch, P J; Johansen, J D; Menné, T; Pirker, C; Rastogi, S C; Andersen, K E; Bruze, M; Goossens, A; Lepoittevin, J P; White, I R

2002-08-01

The aim of this study was to determine the frequency of responses to selected fragrance materials in consecutive patients patch tested in 6 dermatological centres in Europe. 1855 patients were evaluated with the 8% fragrance mix (FM) and 14 other frequently used well-defined fragrance chemicals (series I). Each patient was classified regarding a history of adverse reactions to fragrances: certain, probable, questionable, none. Reactions to FM occurred in 11.3% of the subjects. The 6 substances with the highest reactivity following FM were Lyral (2.7%), citral (1.1%), farnesol P (0.5%), citronellol (0.4%), hexyl cinnamic aldehyde (0.3%), and coumarin (0.3%). 41 (2.2%) of the patients reacted only to materials of series I and not to FM. 6.6% of 1855 patients gave a history of adverse reactions to fragrances which was classified as certain. This group reacted to FM only in 41.1%, to series I and FM in 12.0% and to series I only in 7.2%. 74.3% of the 39 patients reacting to both FM and 1 of the materials of series I had any type of positive fragrance history, which was significantly higher in comparison to those with isolated reactions to series I (53.6% of 41), p = 0.04. The study identified further sensitizers relevant for patch testing of patients with contact dermatitis, of which Lyral is the most important single chemical.

Testing and validating environmental models

USGS Publications Warehouse

Kirchner, J.W.; Hooper, R.P.; Kendall, C.; Neal, C.; Leavesley, G.

1996-01-01

Generally accepted standards for testing and validating ecosystem models would benefit both modellers and model users. Universally applicable test procedures are difficult to prescribe, given the diversity of modelling approaches and the many uses for models. However, the generally accepted scientific principles of documentation and disclosure provide a useful framework for devising general standards for model evaluation. Adequately documenting model tests requires explicit performance criteria, and explicit benchmarks against which model performance is compared. A model's validity, reliability, and accuracy can be most meaningfully judged by explicit comparison against the available alternatives. In contrast, current practice is often characterized by vague, subjective claims that model predictions show 'acceptable' agreement with data; such claims provide little basis for choosing among alternative models. Strict model tests (those that invalid models are unlikely to pass) are the only ones capable of convincing rational skeptics that a model is probably valid. However, 'false positive' rates as low as 10% can substantially erode the power of validation tests, making them insufficiently strict to convince rational skeptics. Validation tests are often undermined by excessive parameter calibration and overuse of ad hoc model features. Tests are often also divorced from the conditions under which a model will be used, particularly when it is designed to forecast beyond the range of historical experience. In such situations, data from laboratory and field manipulation experiments can provide particularly effective tests, because one can create experimental conditions quite different from historical data, and because experimental data can provide a more precisely defined 'target' for the model to hit. We present a simple demonstration showing that the two most common methods for comparing model predictions to environmental time series (plotting model time series against data time series, and plotting predicted versus observed values) have little diagnostic power. We propose that it may be more useful to statistically extract the relationships of primary interest from the time series, and test the model directly against them.

Auto-Thermal Reforming of Jet-A Fuel over Commercial Monolith Catalysts: MicroReactor Evaluation and Screening Test Results

NASA Technical Reports Server (NTRS)

Yen, Judy C. H.; Tomsik, Thomas M.

2004-01-01

This paper describes the results of a series of catalyst screening tests conducted with Jet-A fuel under auto-thermal reforming (ATR) process conditions at the research laboratories of SOFCo-EFS Holdings LLC under Glenn Research Center Contract. The primary objective is to identify best available catalysts for future testing at the NASA GRC 10-kW(sub e) reformer test facility. The new GRC reformer-injector test rig construction is due to complete by March 2004. Six commercially available monolithic catalyst materials were initially selected by the NASA/SOFCo team for evaluation and bench scale screening in an existing 0.05 kW(sub e) microreactor test apparatus. The catalyst screening tests performed lasted 70 to 100 hours in duration in order to allow comparison between the different samples over a defined range of ATR process conditions. Aging tests were subsequently performed with the top two ranked catalysts as a more representative evaluation of performance in a commercial aerospace application. The two catalyst aging tests conducted lasting for approximately 600 hours and 1000 hours, respectively.

Nondestructive tests of regenerative chambers. [evaluating nondestructive methods of determining metal bond integrity

NASA Technical Reports Server (NTRS)

Malone, G. A.; Vecchies, L.; Wood, R.

1974-01-01

The capabilities and limitations of nondestructive evaluation methods were studied to detect and locate bond deficiencies in regeneratively cooled thrust chambers for rocket engines. Flat test panels and a cylinder were produced to simulate regeneratively cooled thrust chamber walls. Planned defects with various bond integrities were produced in the panels to evaluate the sensitivity, accuracy, and limitations of nondestructive methods to define and locate bond anomalies. Holography, acoustic emission, and ultrasonic scan were found to yield sufficient data to discern bond quality when used in combination and in selected sequences. Bonding techniques included electroforming and brazing. Materials of construction included electroformed nickel bonded to Nickel 200 and OFHC copper, electroformed copper bonded to OFHC copper, and 300 series stainless steel brazed to OFHC copper. Variations in outer wall strength, wall thickness, and defect size were evaluated for nondestructive test response.

Comparison of Statistical Algorithms for the Detection of Infectious Disease Outbreaks in Large Multiple Surveillance Systems

PubMed Central

Farrington, C. Paddy; Noufaily, Angela; Andrews, Nick J.; Charlett, Andre

2016-01-01

A large-scale multiple surveillance system for infectious disease outbreaks has been in operation in England and Wales since the early 1990s. Changes to the statistical algorithm at the heart of the system were proposed and the purpose of this paper is to compare two new algorithms with the original algorithm. Test data to evaluate performance are created from weekly counts of the number of cases of each of more than 2000 diseases over a twenty-year period. The time series of each disease is separated into one series giving the baseline (background) disease incidence and a second series giving disease outbreaks. One series is shifted forward by twelve months and the two are then recombined, giving a realistic series in which it is known where outbreaks have been added. The metrics used to evaluate performance include a scoring rule that appropriately balances sensitivity against specificity and is sensitive to variation in probabilities near 1. In the context of disease surveillance, a scoring rule can be adapted to reflect the size of outbreaks and this was done. Results indicate that the two new algorithms are comparable to each other and better than the algorithm they were designed to replace. PMID:27513749

Taking a Concept to Commercialization: Designing Relevant Tests to Address Safety.

PubMed

Ferrara, Lisa A

2016-04-01

Taking a product from concept to commercialization requires careful navigation of the regulatory pathway through a series of steps: (A) moving the idea through proof of concept and beyond; (B) evaluating new technologies that may provide added value to the idea; (C) designing appropriate test strategies and protocols; and (D) evaluating and mitigating risks. Moving an idea from the napkin stage of development to the final product requires a team effort. When finished, the product rarely resembles the original design, but careful steps throughout the product life cycle ensure that the product meets the vision.

Development of a model for occipital fixation--validation of an analogue bone material.

PubMed

Mullett, H; O'Donnell, T; Felle, P; O'Rourke, K; FitzPatrick, D

2002-01-01

Several implant systems may be used to fuse the skull to the upper cervical spine (occipitocervical fusion). Current biomechanical evaluation is restricted by the limitations of human cadaveric specimens. This paper describes the design and validation of a synthetic testing model of the occipital bone. Data from thickness measurement and pull-out strength testing of a series of human cadaveric skulls was used in the design of a high-density rigid polyurethane foam model. The synthetic occipital model demonstrated repeatable and consistent morphological and biomechanical properties. The model provides a standardized environment for evaluation of occipital implants.

Test evaluation of a laminated wood wind turbine blade concept

NASA Technical Reports Server (NTRS)

Faddoul, J. R.

1981-01-01

A series of tests conducted on a root end section of a laminated wood wind turbine blade are reported. The blade to hub transition of the wood blade uses steel studs cast into the wood D spar with a filled epoxy. Both individual studs and a full scale, short length, root section were tested. Results indicate that the bonded stud concept is more than adequate for both the 30 year life fatigue loads and for the high wind or hurricane gust loads.

Vertical Impact Tests of a Modified F/FB-111 Crew Seat to Evaluate Headrest Position and Restraint Configuration Effects

DTIC Science & Technology

1982-08-01

Deceleration Tower (VDT), shown in Figure 9, was used for this impact test series. This facility consists of a 60 ft vertical steel tower, which supports a...to void prior to entering the test area. A disposable dental bite block (made of Optosil placed over a stainless steel frame) was molded for the...shoulder strap - lap belt configuration (Sections 4D, 5C). 6. Subtolerance human impact tests can be an effective tool in the investi- gation of impact

Identification of commercially available alloys for corrosion-resistant metallic reinforcement and test methods for evaluating corrosion-resistant reinforcement.

DOT National Transportation Integrated Search

2008-01-01

A literature review was conducted with the goal of identifying alternative low-cost corrosion-resistant steel reinforcement materials. The most promising alternate reinforcing materials seen to date that are less expensive than 300 series stainless s...

A randomized intervention of reminder letter for human papillomavirus vaccine series completion.

PubMed

Chao, Chun; Preciado, Melissa; Slezak, Jeff; Xu, Lanfang

2015-01-01

Completion rate for the three-dose series of the human papillomavirus (HPV) vaccine has generally been low. This study evaluated the effectiveness of a reminder letter intervention on HPV vaccine three-dose series completion. Female members of Kaiser Permanente Southern California Health Plan who received at least one dose, but not more than two doses, of the HPV vaccine by February 13, 2013, and who were between ages 9 and 26 years at the time of first HPV vaccination were included. Eighty percent of these females were randomized to receive the reminder letter, and 20% were randomized to receive standard of care (control). The reminder letters were mailed quarterly to those who had not completed the series. The proportion of series completion at the end of the 12-month evaluation period was compared using chi-square test. A total of 9,760 females were included in the intervention group and 2,445 in the control group. HPV vaccine series completion was 56.4% in the intervention group and 46.6% in the control groups (p < .001). The effect of the intervention appeared to be stronger in girls aged 9-17 years compared with young women aged 18-26 years at the first dose and in blacks compared with whites. Reminder letters scheduled quarterly were effective to enhance HPV vaccine series completion among those who initiated the vaccine. However, a large gap in series completion remained despite the intervention. Future studies should address other barriers to series completion, including those at the providers and the health care system level. Copyright © 2015 Society for Adolescent Health and Medicine. Published by Elsevier Inc. All rights reserved.

Hybrid poplar grows poorly on acid spoil banks at high elevations in West Virginia

Treesearch

George R., Jr. Trimble

1963-01-01

In the early 1950s, a region-wide series of hybrid poplar clonal tests was begun in the Northeast to evaluate the performance of 50 selected clones under a variety of site and climatic conditions. The basic test unit was a block of 50 randomized plots-1 plot for each of the 50 clones. In each plot, 16 cuttings were planted at 4-foot spacing.

PM₁₀ exposure and non-accidental mortality in Asian populations: a meta-analysis of time-series and case-crossover studies.

PubMed

Park, Hye Yin; Bae, Sanghyuk; Hong, Yun-Chul

2013-01-01

We investigated the association between particulate matter less than 10 µm in aerodynamic diameter (PM₁₀) exposure and non-accidental mortality in Asian populations by meta-analysis, using both time-series and case-crossover analysis. Among the 819 published studies searched from PubMed and EMBASE using key words related to PM₁₀ exposure and non-accidental mortality in Asian countries, 8 time-series and 4 case-crossover studies were selected for meta-analysis after exclusion by selection criteria. We obtained the relative risk (RR) and 95% confidence intervals (CI) of non-accidental mortality per 10 µg/m³ increase of daily PM₁₀ from each study. We used Q statistics to test the heterogeneity of the results among the different studies and evaluated for publication bias using Begg funnel plot and Egger test. Testing for heterogeneity showed significance (p<0.001); thus, we applied a random-effects model. RR (95% CI) per 10 µg/m³ increase of daily PM₁₀ for both the time-series and case-crossover studies combined, time-series studies relative risk only, and case-crossover studies only, were 1.0047 (1.0033 to 1.0062), 1.0057 (1.0029 to 1.0086), and 1.0027 (1.0010 to 1.0043), respectively. The non-significant Egger test suggested that this analysis was not likely to have a publication bias. We found a significant positive association between PM₁₀ exposure and non-accidental mortality among Asian populations. Continued investigations are encouraged to contribute to the health impact assessment and public health management of air pollution in Asian countries.

Data imputation analysis for Cosmic Rays time series

NASA Astrophysics Data System (ADS)

Fernandes, R. C.; Lucio, P. S.; Fernandez, J. H.

2017-05-01

The occurrence of missing data concerning Galactic Cosmic Rays time series (GCR) is inevitable since loss of data is due to mechanical and human failure or technical problems and different periods of operation of GCR stations. The aim of this study was to perform multiple dataset imputation in order to depict the observational dataset. The study has used the monthly time series of GCR Climax (CLMX) and Roma (ROME) from 1960 to 2004 to simulate scenarios of 10%, 20%, 30%, 40%, 50%, 60%, 70%, 80% and 90% of missing data compared to observed ROME series, with 50 replicates. Then, the CLMX station as a proxy for allocation of these scenarios was used. Three different methods for monthly dataset imputation were selected: AMÉLIA II - runs the bootstrap Expectation Maximization algorithm, MICE - runs an algorithm via Multivariate Imputation by Chained Equations and MTSDI - an Expectation Maximization algorithm-based method for imputation of missing values in multivariate normal time series. The synthetic time series compared with the observed ROME series has also been evaluated using several skill measures as such as RMSE, NRMSE, Agreement Index, R, R2, F-test and t-test. The results showed that for CLMX and ROME, the R2 and R statistics were equal to 0.98 and 0.96, respectively. It was observed that increases in the number of gaps generate loss of quality of the time series. Data imputation was more efficient with MTSDI method, with negligible errors and best skill coefficients. The results suggest a limit of about 60% of missing data for imputation, for monthly averages, no more than this. It is noteworthy that CLMX, ROME and KIEL stations present no missing data in the target period. This methodology allowed reconstructing 43 time series.

Development of a statistically proven injection molding method for reaction bonded silicon nitride, sintering reaction bonded silicon nitride, and sintered silicon nitride

NASA Astrophysics Data System (ADS)

Steiner, Matthias

A statistically proven, series injection molding technique for ceramic components was developed for the construction of engines and gas turbines. The flow behavior of silicon injection-molding materials was characterized and improved. Hot-isostatic-pressing reaction bonded silicon nitride (HIPRBSN) was developed. A nondestructive component evaluation method was developed. An injection molding line for HIPRBSN engine components precombustion chamber, flame spreader, and valve guide was developed. This line allows the production of small series for engine tests.

Industrial application experiment series

NASA Technical Reports Server (NTRS)

Bluhm, S. A.

1981-01-01

Two procurements within the Industrial Application Experiment Series of the Thermal Power Systems Project are discussed. The first procurement, initiated in April 1980, resulted in an award to the Applied Concepts Corporation for the Capital Concrete Experiment: two Fresnel concentrating collectors will be evaluated in single-unit installations at the Jet Propulsion Laboratory Parabolic Dish Test Site and at Capitol Concrete Products, Topeka, Kansas. The second procurement, initiated in March 1981, is titled, "Thermal System Engineering Experiment B." The objective of the procurement is the rapid deployment of developed parabolic dish collectors.

Comparison of attrition test methods: ASTM standard fluidized bed vs jet cup

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhao, R.; Goodwin, J.G. Jr.; Jothimurugesan, K.

2000-05-01

Attrition resistance is one of the key design parameters for catalysts used in fluidized-bed and slurry phase types of reactors. The ASTM fluidized-bed test has been one of the most commonly used attrition resistance evaluation methods; however, it requires the use of 50 g samples--a large amount for catalyst development studies. Recently a test using the jet cup requiring only 5 g samples has been proposed. In the present study, two series of spray-dried iron catalysts were evaluated using both the ASTM fluidized-bed test and a test based on the jet cup to determine this comparability. It is shown thatmore » the two tests give comparable results. This paper, by reporting a comparison of the jet-cup test with the ASTM standard, provides a basis for utilizing the more efficient jet cup with confidence in catalyst attrition studies.« less

The utility of patch tests using larger screening series of allergens.

PubMed

Larkin, A; Rietschel, R L

1998-09-01

The number of patch test allergens available within the United States for routine commercial purchase is limited. Allergens chosen for inclusion in routine screening series or patch test trays vary, and the degree of information obtained from any series may or may not serve a patient's needs. Knowledge of how well the allergens chosen for inclusion in the two commercially available sources perform compared with a more expansive panel of tests can help physicians select the more appropriate tests. From 1994 to mid-1997, 554 patients were tested with allergens recommended by the North American Contact Dermatitis Group (NACDG). This included all allergens currently available from both current domestic sources, although not in the identical form used by the Thin-layer Rapid Use Epicutaneous Test (TRUE) test (Glaxo Dermatology, Research Triangle Park, NC). Another 185 patients were tested with supplemental series of allergens. The larger the series of allergens used, the more positive tests were found and the more relevant tests as well. Hermal patch test allergens identified about 55% of the information found by the NACDG series; the TRUE test allergens (but not in the TRUE test system) identified 65%. Of the 103 reactions to supplemental allergens not found by the NACDG series, 59 were relevant. Larger series of allergens can enhance accurate diagnosis of allergic contact dermatitis. No single arbitrary series of allergens can adequately survey the contemporary environment of individual patients. Selection of allergens for testing requires consideration of the patient's history and access to appropriate environmental contactants.

Crew Exploration Vehicle Launch Abort Controller Performance Analysis

NASA Technical Reports Server (NTRS)

Sparks, Dean W., Jr.; Raney, David L.

2007-01-01

This paper covers the simulation and evaluation of a controller design for the Crew Module (CM) Launch Abort System (LAS), to measure its ability to meet the abort performance requirements. The controller used in this study is a hybrid design, including features developed by the Government and the Contractor. Testing is done using two separate 6-degree-of-freedom (DOF) computer simulation implementations of the LAS/CM throughout the ascent trajectory: 1) executing a series of abort simulations along a nominal trajectory for the nominal LAS/CM system; and 2) using a series of Monte Carlo runs with perturbed initial flight conditions and perturbed system parameters. The performance of the controller is evaluated against a set of criteria, which is based upon the current functional requirements of the LAS. Preliminary analysis indicates that the performance of the present controller meets (with the exception of a few cases) the evaluation criteria mentioned above.

Physical properties of the benchmark models program supercritical wing

NASA Technical Reports Server (NTRS)

Dansberry, Bryan E.; Durham, Michael H.; Bennett, Robert M.; Turnock, David L.; Silva, Walter A.; Rivera, Jose A., Jr.

1993-01-01

The goal of the Benchmark Models Program is to provide data useful in the development and evaluation of aeroelastic computational fluid dynamics (CFD) codes. To that end, a series of three similar wing models are being flutter tested in the Langley Transonic Dynamics Tunnel. These models are designed to simultaneously acquire model response data and unsteady surface pressure data during wing flutter conditions. The supercritical wing is the second model of this series. It is a rigid semispan model with a rectangular planform and a NASA SC(2)-0414 supercritical airfoil shape. The supercritical wing model was flutter tested on a flexible mount, called the Pitch and Plunge Apparatus, that provides a well-defined, two-degree-of-freedom dynamic system. The supercritical wing model and associated flutter test apparatus is described and experimentally determined wind-off structural dynamic characteristics of the combined rigid model and flexible mount system are included.

Evaluation of a clinical decision support tool for osteoporosis disease management: protocol for an interrupted time series design.

PubMed

Kastner, Monika; Sawka, Anna; Thorpe, Kevin; Chignel, Mark; Marquez, Christine; Newton, David; Straus, Sharon E

2011-07-22

Osteoporosis affects over 200 million people worldwide at a high cost to healthcare systems. Although guidelines on assessing and managing osteoporosis are available, many patients are not receiving appropriate diagnostic testing or treatment. Findings from a systematic review of osteoporosis interventions, a series of mixed-methods studies, and advice from experts in osteoporosis and human-factors engineering were used collectively to develop a multicomponent tool (targeted to family physicians and patients at risk for osteoporosis) that may support clinical decision making in osteoporosis disease management at the point of care. A three-phased approach will be used to evaluate the osteoporosis tool. In phase 1, the tool will be implemented in three family practices. It will involve ensuring optimal functioning of the tool while minimizing disruption to usual practice. In phase 2, the tool will be pilot tested in a quasi-experimental interrupted time series (ITS) design to determine if it can improve osteoporosis disease management at the point of care. Phase 3 will involve conducting a qualitative postintervention follow-up study to better understand participants' experiences and perceived utility of the tool and readiness to adopt the tool at the point of care. The osteoporosis tool has the potential to make several contributions to the development and evaluation of complex, chronic disease interventions, such as the inclusion of an implementation strategy prior to conducting an evaluation study. Anticipated benefits of the tool may be to increase awareness for patients about osteoporosis and its associated risks and provide an opportunity to discuss a management plan with their physician, which may all facilitate patient self-management.

Evaluation of a clinical decision support tool for osteoporosis disease management: protocol for an interrupted time series design

PubMed Central

2011-01-01

Background Osteoporosis affects over 200 million people worldwide at a high cost to healthcare systems. Although guidelines on assessing and managing osteoporosis are available, many patients are not receiving appropriate diagnostic testing or treatment. Findings from a systematic review of osteoporosis interventions, a series of mixed-methods studies, and advice from experts in osteoporosis and human-factors engineering were used collectively to develop a multicomponent tool (targeted to family physicians and patients at risk for osteoporosis) that may support clinical decision making in osteoporosis disease management at the point of care. Methods A three-phased approach will be used to evaluate the osteoporosis tool. In phase 1, the tool will be implemented in three family practices. It will involve ensuring optimal functioning of the tool while minimizing disruption to usual practice. In phase 2, the tool will be pilot tested in a quasi-experimental interrupted time series (ITS) design to determine if it can improve osteoporosis disease management at the point of care. Phase 3 will involve conducting a qualitative postintervention follow-up study to better understand participants' experiences and perceived utility of the tool and readiness to adopt the tool at the point of care. Discussion The osteoporosis tool has the potential to make several contributions to the development and evaluation of complex, chronic disease interventions, such as the inclusion of an implementation strategy prior to conducting an evaluation study. Anticipated benefits of the tool may be to increase awareness for patients about osteoporosis and its associated risks and provide an opportunity to discuss a management plan with their physician, which may all facilitate patient self-management. PMID:21781318

Testing and Analytical Modeling for Purging Process of a Cryogenic Line

NASA Technical Reports Server (NTRS)

Hedayat, A.; Mazurkivich, P. V.; Nelson, M. A.; Majumdar, A. K.

2015-01-01

To gain confidence in developing analytical models of the purging process for the cryogenic main propulsion systems of upper stage, two test series were conducted. Test article, a 3.35m long with the diameter of 20 cm incline line, was filled with liquid (LH2)or gaseous hydrogen (GH2) and then purged with gaseous helium (GHe). Total of 10 tests were conducted. Influences of GHe flow rates and initial temperatures were evaluated. Generalized Fluid System Simulation Program (GFSSP), an in-house general-purpose fluid system analyzer, was utilized to model and simulate selective tests.

Space Shuttle Orbiter Approach and Landing Test Evaluation Report. Captive-Active Flight Test Summary

NASA Technical Reports Server (NTRS)

1977-01-01

Captive-active tests consisted of three mated carrier aircraft/Orbiter flights with an active manned Orbiter. The objectives of this series of flights were to (1) verify the separation profile, (2) verify the integrated structure, aerodynamics, and flight control system, (3) verify Orbiter integrated system operations, and (4) refine and finalize carrier aircraft, Orbiter crew, and ground procedures in preparation for free flight tests. A summary description of the flights is presented with assessments of flight test requirements, and of the performance operations, and of significant flight anomalies is included.

Modeling cross-hole slug tests in an unconfined aquifer

DOE PAGES

Malama, Bwalya; Kuhlman, Kristopher L.; Brauchler, Ralf; ...

2016-06-28

Cross-hole slug test date are analyzed with an extended version of a recently published unconfined aquifer model accounting for waterable effects using the linearized kinematic condition. The use of cross-hole slug test data to characterize aquifer heterogeneity and source/observation well oscillation parameters is evaluated. The data were collected in a series of multi-well and multi-level pneumatic slug tests conducted at a site in Widen, Switzerland. Furthermore, the tests involved source and observation well pairs separated by distances of up to 4 m, and instrumented with pressure transducers to monitor aquifer response in discrete intervals.

Space shuttle maneuvering engine reusable thrust chamber program. Task 11: Stability analyses and acoustic model testing data dump

NASA Technical Reports Server (NTRS)

Oberg, C. L.

1974-01-01

The combustion stability characteristics of engines applicable to the Space Shuttle Orbit Maneuvering System and the adequacy of acoustic cavities as a means of assuring stability in these engines were investigated. The study comprised full-scale stability rating tests, bench-scale acoustic model tests and analysis. Two series of stability rating tests were made. Acoustic model tests were made to determine the resonance characteristics and effects of acoustic cavities. Analytical studies were done to aid design of the cavity configurations to be tested and, also, to aid evaluation of the effectiveness of acoustic cavities from available test results.

A high throughput passive dosing format for the Fish Embryo Acute Toxicity test.

PubMed

Vergauwen, Lucia; Schmidt, Stine N; Stinckens, Evelyn; Maho, Walid; Blust, Ronny; Mayer, Philipp; Covaci, Adrian; Knapen, Dries

2015-11-01

High throughput testing according to the Fish Embryo Acute Toxicity (FET) test (OECD Testing Guideline 236) is usually conducted in well plates. In the case of hydrophobic test substances, sorptive and evaporative losses often result in declining and poorly controlled exposure conditions. Therefore, our objective was to improve exposure conditions in FET tests by evaluating a passive dosing format using silicone O-rings in standard 24-well polystyrene plates. We exposed zebrafish embryos to a series of phenanthrene concentrations until 120h post fertilization (hpf), and obtained a linear dilution series. We report effect values for both mortality and sublethal morphological effects based on (1) measured exposure concentrations, (2) (lipid normalized) body residues and (3) chemical activity. The LC50 for 120hpf was 310μg/L, CBR50 (critical body residue) was 2.72mmol/kg fresh wt and La50 (lethal chemical activity) was 0.047. All values were within ranges expected for baseline toxicity. Impaired swim bladder inflation was the most pronounced morphological effect and swimming activity was reduced in all exposure concentrations. Further analysis showed that the effect on swimming activity was not attributed to impaired swim bladder inflation, but rather to baseline toxicity. We conclude that silicone O-rings (1) produce a linear dilution series of phenanthrene in the 120hpf FET test, (2) generate and maintain aqueous concentrations for reliable determination of effect concentrations, and allow for obtaining mechanistic toxicity information, and (3) cause no toxicity, demonstrating its potential as an extension of the FET test when testing hydrophobic chemicals. Copyright © 2015 Elsevier Ltd. All rights reserved.

Performance evaluation approach for the supercritical helium cold circulators of ITER

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vaghela, H.; Sarkar, B.; Bhattacharya, R.

2014-01-29

The ITER project design foresees Supercritical Helium (SHe) forced flow cooling for the main cryogenic components, namely, the superconducting (SC) magnets and cryopumps (CP). Therefore, cold circulators have been selected to provide the required SHe mass flow rate to cope with specific operating conditions and technical requirements. Considering the availability impacts of such machines, it has been decided to perform evaluation tests of the cold circulators at operating conditions prior to the series production in order to minimize the project technical risks. A proposal has been conceptualized, evaluated and simulated to perform representative tests of the full scale SHe coldmore » circulators. The objectives of the performance tests include the validation of normal operating condition, transient and off-design operating modes as well as the efficiency measurement. A suitable process and instrumentation diagram of the test valve box (TVB) has been developed to implement the tests at the required thermodynamic conditions. The conceptual engineering design of the TVB has been developed along with the required thermal analysis for the normal operating conditions to support the performance evaluation of the SHe cold circulator.« less

Z-1 Prototype Space Suit Testing Summary

NASA Technical Reports Server (NTRS)

Ross, Amy

2013-01-01

The Advanced Space Suit team of the NASA-Johnson Space Center performed a series of test with the Z-1 prototype space suit in 2012. This paper discusses, at a summary level, the tests performed and results from those tests. The purpose of the tests were two-fold: 1) characterize the suit performance so that the data could be used in the downselection of components for the Z-2 Space Suit and 2) develop interfaces with the suitport and exploration vehicles through pressurized suit evaluations. Tests performed included isolated and functional range of motion data capture, Z-1 waist and hip testing, joint torque testing, CO2 washout testing, fit checks and subject familiarizations, an exploration vehicle aft deck and suitport controls interface evaluation, delta pressure suitport tests including pressurized suit don and doff, and gross mobility and suitport ingress and egress demonstrations in reduced gravity. Lessons learned specific to the Z-1 prototype and to suit testing techniques will be presented.

Z-1 Prototype Space Suit Testing Summary

NASA Technical Reports Server (NTRS)

Ross, Amy J.

2012-01-01

The Advanced Space Suit team of the NASA-Johnson Space Center performed a series of test with the Z-1 prototype space suit in 2012. This paper discusses, at a summary level, the tests performed and results from those tests. The purpose of the tests were two -fold: 1) characterize the suit performance so that the data could be used in the downselection of components for the Z -2 Space Suit and 2) develop interfaces with the suitport and exploration vehicles through pressurized suit evaluations. Tests performed included isolated and functional range of motion data capture, Z-1 waist and hip testing, joint torque testing, CO2 washout testing, fit checks and subject familiarizations, an exploration vehicle aft deck and suitport controls interface evaluation, delta pressure suitport tests including pressurized suit don and doff, and gross mobility and suitport ingress and egress demonstrations in reduced gravity. Lessons learned specific to the Z -1 prototype and to suit testing techniques will be presented.

Project Developmental Continuity: Field Procedures Manual.

ERIC Educational Resources Information Center

Morris, Mary

This operations manual for field staff (site monitors, site coordinators, and testers) involved in the observation and testing of children is part of a series of documents on the evaluation of Project Developmental Continuity (PDC), a Head Start demonstration program aimed at providing educational and developmental continuity between children's…

Personnel Development for Entrepreneurs.

ERIC Educational Resources Information Center

Sanders, Leon; And Others

Divided into three units, this curriculum guide on entrepreneur education covers nineteen individual areas of instruction and can be conducted in a series of nine workshops. (The development, field testing, and evaluation of the curriculum are reported separately as CE 015 581.) Unit I covers the following areas of instruction: planning,…

An Audiovisual Program in Cell Biology

ERIC Educational Resources Information Center

Fedoroff, Sergey; Opel, William

1978-01-01

A subtopic of cell biology, the structure and function of cell membranes, has been developed as a series of seven self-instructional slide-tape units and tested in five medical schools. Organization of advisers, analysis and definition of objectives and content, and development and evaluation of scripts and storyboards are discussed. (Author/LBH)

Laboratory evaluation of particle size, food contamination, and residual efficacy of pyrethrin + methoprene aerosol

USDA-ARS?s Scientific Manuscript database

A series of tests were conducted to determine residual efficacy of pyrethrin+methoprene aerosol to manage larvae of selected stored product insects. Efficacy was assessed through emergence of morphologically-normal adults and through a quantitative developmental index with values ranging from 1, for...

Authentic Assessment: A Handbook for Educators. Assessment Bookshelf Series.

ERIC Educational Resources Information Center

Hart, Diane

This book reviews the assessment movement, from the history of testing to the practical considerations of enhancing classroom experiences for teachers and students. It explores making time for assessment, tailoring assessment to desired outcomes, and scoring and evaluating student performance. The chapters are: (1) "Where We've Been: Standardized…

Susceptibility of selected stored product insects to a combination treatment of pyriproxyfen and novaluron

USDA-ARS?s Scientific Manuscript database

A series of tests was conducted to evaluate susceptibility of Tribolium castaneum (Herbst), the red flour beetle, Trogoderma variabile (Ballion), the warehouse beetle, and Dermestes maculatus (DeGeer), the hide beetle, to a new insecticide (Tekko®) which contained the IGR pyreproxyfen and the chiten...

Fire performance of oriented strandboard

Treesearch

Robert H. White; Jerrold E. Winandy

2006-01-01

Wood-based composites represent a continuously increasing share of the wood products market. Commercial construction will be important for future expansion of the structural panels market. Use of engineered wood products as an alternative to traditional solid wood lumber is also increasing. A recent series of cone calorimeter tests evaluated the performance of several...

ENVIRONMENTAL TECHNOLOGY VERIFICATION REPORT - LEAD IN DUST WIPE MEASUREMENT TECHNOLOGY, NITON CORPORATION, X-RAY FLUORESCENCE SPECTRUM ANALYSER, XL-300 SERIES

EPA Science Inventory

ETV works in partnership with recognized standards and testing organizations and stakeholder groups consisting of regulators, buyers, and vendor organizations, with the full participation of individual technology developers. The program evaluates the performance of innovative

Evaluation of Life Sciences Glovebox (LSG) and Multi-Purpose Crew Restraint Concepts

NASA Technical Reports Server (NTRS)

Whitmore, Mihriban

2005-01-01

Within the scope of the Multi-purpose Crew Restraints for Long Duration Spaceflights project, funded by Code U, it was proposed to conduct a series of evaluations on the ground and on the KC-135 to investigate the human factors issues concerning confined/unique workstations, such as the design of crew restraints. The usability of multiple crew restraints was evaluated for use with the Life Sciences Glovebox (LSG) and for performing general purpose tasks. The purpose of the KC-135 microgravity evaluation was to: (1) to investigate the usability and effectiveness of the concepts developed, (2) to gather recommendations for further development of the concepts, and (3) to verify the validity of the existing requirements. Some designs had already been tested during a March KC-135 evaluation, and testing revealed the need for modifications/enhancements. This flight was designed to test the new iterations, as well as some new concepts. This flight also involved higher fidelity tasks in the LSG, and the addition of load cells on the gloveports.

Joint modelling of annual maximum drought severity and corresponding duration

NASA Astrophysics Data System (ADS)

Tosunoglu, Fatih; Kisi, Ozgur

2016-12-01

In recent years, the joint distribution properties of drought characteristics (e.g. severity, duration and intensity) have been widely evaluated using copulas. However, history of copulas in modelling drought characteristics obtained from streamflow data is still short, especially in semi-arid regions, such as Turkey. In this study, unlike previous studies, drought events are characterized by annual maximum severity (AMS) and corresponding duration (CD) which are extracted from daily streamflow of the seven gauge stations located in Çoruh Basin, Turkey. On evaluation of the various univariate distributions, the Exponential, Weibull and Logistic distributions are identified as marginal distributions for the AMS and CD series. Archimedean copulas, namely Ali-Mikhail-Haq, Clayton, Frank and Gumbel-Hougaard, are then employed to model joint distribution of the AMS and CD series. With respect to the Anderson Darling and Cramér-von Mises statistical tests and the tail dependence assessment, Gumbel-Hougaard copula is identified as the most suitable model for joint modelling of the AMS and CD series at each station. Furthermore, the developed Gumbel-Hougaard copulas are used to derive the conditional and joint return periods of the AMS and CD series which can be useful for designing and management of reservoirs in the basin.

Statistical Analysis of CFD Solutions from the Drag Prediction Workshop

NASA Technical Reports Server (NTRS)

Hemsch, Michael J.

2002-01-01

A simple, graphical framework is presented for robust statistical evaluation of results obtained from N-Version testing of a series of RANS CFD codes. The solutions were obtained by a variety of code developers and users for the June 2001 Drag Prediction Workshop sponsored by the AIAA Applied Aerodynamics Technical Committee. The aerodynamic configuration used for the computational tests is the DLR-F4 wing-body combination previously tested in several European wind tunnels and for which a previous N-Version test had been conducted. The statistical framework is used to evaluate code results for (1) a single cruise design point, (2) drag polars and (3) drag rise. The paper concludes with a discussion of the meaning of the results, especially with respect to predictability, Validation, and reporting of solutions.

1-(substituted benzyl)-3,4,5,6-tetrahydro-2(1H)-pyrimidones: a series with stimulant and depressant activities.

PubMed

Ellis, K O; Schwan, T J; Wessels, F L; Miles, N J

1980-10-01

A series of 1-(substituted benzyl)-3,4,5,6-tetrahydro-2(1H)-pyrimidones was synthesized primarily by catalytic hydrogenation of the corresponding 1-(substituted benzyl)-2(1H)-pyrimidone. The pharmacological evaluation of these compounds in mice revealed a unique profile that included evidence of CNS stimulation and depression within the series and in the same compounds. Some members of this series induced signs of only CNS stimulation, some compounds caused signs of only CNS depression and skeletal muscle relaxation, and some caused signs of both stimulation and depression in the same animal. This apparent dual activity was assessed further in mice with antidepressant tests based on tetrabenazine antagonism and with antianxiety/anticonvulsant tests on the antagonism of a number of convulsants. The 4-chloro-, 4-fluoro-, 4-bromo-, and 3,4-dichlorobenzyl compounds exhibited antidepressant and antianxiety activities in the same dose range. Among these four compounds, the 3,4-dichlorobenzyl compound possessed the lowest antitetrabenazine (17 mg/kg po) and antipentylenetetrazol (23 mg/kg po) ED50 values. The 4-fluoro compound antagonized tetrabenazine-, pentylenetetrazol-, and isoniazid-induced tonic convulsions in the same dose range (congruent to 50 mg/kg po).

Analytical and clinical performance of the Hologic Aptima HCV Quant Dx Assay for the quantification of HCV RNA in plasma samples.

PubMed

Schønning, Kristian; Pedersen, Martin Schou; Johansen, Kim; Landt, Bodil; Nielsen, Lone Gilmor; Weis, Nina; Westh, Henrik

2017-10-01

Chronic hepatitis C virus (HCV) infection can be effectively treated with directly acting antiviral (DAA) therapy. Measurement of HCV RNA is used to evaluate patient compliance and virological response during and after treatment. To compare the analytical performance of the Aptima HCV Quant Dx Assay (Aptima) and the COBAS Ampliprep/COBAS TaqMan HCV Test v2.0 (CAPCTMv2) for the quantification of HCV RNA in plasma samples, and compare the clinical utility of the two tests in patients undergoing treatment with DAA therapy. Analytical performance was evaluated on two sets of plasma samples: 125 genotyped samples and 172 samples referred for quantification of HCV RNA. Furthermore, performance was evaluated using dilutions series of four samples containing HCV genotype 1a, 2b, 3a, and 4a, respectively. Clinical utility was evaluated on 118 plasma samples obtained from 13 patients undergoing treatment with DAAs. Deming regression of results from 187 plasma samples with HCV RNA >2 Log IU/mL indicated that the Aptima assay quantified higher than the CAPCTMv2 test for HCV RNA >4.9 Log IU/mL. The linearity of the Aptima assay was excellent across dilution series of four HCV genotypes (slope of the regression line: 1.00-1.02). The Aptima assay detected significantly more replicates below targeted 2 Log IU/mL than the CAPCTMv2 test, and yielded clearly interpretable results when used to analyze samples from patients treated with DAAs. The analytical performance of the Aptima assay makes it well suited for monitoring patients with chronic HCV infection undergoing antiviral treatment. Copyright © 2017 Elsevier B.V. All rights reserved.

Contact sensitivity to preservatives in Singapore: frequency of sensitization to 11 common preservatives 2006-2011.

PubMed

Cheng, Suzanne; Leow, Yung Hian; Goh, Chee Leok; Goon, Anthony

2014-01-01

Preservatives are indispensable agents used to prevent bacterial and fungal contamination of cosmetics, personal care products, domestic preparations, and industrial products. We evaluated patch-test data at the National Skin Centre, Singapore, from 2006 to 2011 to identify the trends in preservative contact allergies. All patients with suspected contact dermatitis were patch tested to 4 preservatives within the modified European standard series. Patients were also tested with 7 preservatives from our special series if clinically indicated. Three thousand one hundred seventy-seven patients were tested to preservatives in the standard series. Sensitization frequencies were all greater than 1%: parabens (2.58%), methylchloroisothiazolinone/methylisothiazolinone (1.75%), quaternium 15 (1.43%), and methyldibromoglutaronitrile (1.2%). There was no change in trends in sensitization frequencies from 2006 to 2011, with no increase in sensitization frequency to methylchloroisothiazolinone/methylisothiazolinone. The sensitization frequencies for methyldibromoglutaronitrile/phenoxyethanol and diazolidinylurea were 2.03% and 1.37%, respectively, and remained less than 1% for bronopol, imidazolidinyl urea, and 2-phenoxyethanol. A rate of 0% was seen for 1,3-dimethylol-5,5-dimethyl hydantoin and formaldehyde; 9.4% of positive patch-test results became positive only at day 7. Preservatives are common causes of allergic contact dermatitis. This should be considered when introducing new preservatives into the market. Day 7 readings are important to detect late reactions.

Testing activities at the National Battery Test Laboratory

NASA Astrophysics Data System (ADS)

Hornstra, F.; Deluca, W. H.; Mulcahey, T. P.

The National Battery Test Laboratory (NBTL) is an Argonne National Laboratory facility for testing, evaluating, and studying advanced electric storage batteries. The facility tests batteries developed under Department of Energy programs and from private industry. These include batteries intended for future electric vehicle (EV) propulsion, electric utility load leveling (LL), and solar energy storage. Since becoming operational, the NBTL has evaluated well over 1400 cells (generally in the form of three- to six-cell modules, but up to 140-cell batteries) of various technologies. Performance characterization assessments are conducted under a series of charge/discharge cycles with constant current, constant power, peak power, and computer simulated dynamic load profile conditions. Flexible charging algorithms are provided to accommodate the specific needs of each battery under test. Special studies are conducted to explore and optimize charge procedures, to investigate the impact of unique load demands on battery performance, and to analyze the thermal management requirements of battery systems.

Results from a GPS Shuttle Training Aircraft flight test

NASA Technical Reports Server (NTRS)

Saunders, Penny E.; Montez, Moises N.; Robel, Michael C.; Feuerstein, David N.; Aerni, Mike E.; Sangchat, S.; Rater, Lon M.; Cryan, Scott P.; Salazar, Lydia R.; Leach, Mark P.

1991-01-01

A series of Global Positioning System (GPS) flight tests were performed on a National Aeronautics and Space Administration's (NASA's) Shuttle Training Aircraft (STA). The objective of the tests was to evaluate the performance of GPS-based navigation during simulated Shuttle approach and landings for possible replacement of the current Shuttle landing navigation aid, the Microwave Scanning Beam Landing System (MSBLS). In particular, varying levels of sensor data integration would be evaluated to determine the minimum amount of integration required to meet the navigation accuracy requirements for a Shuttle landing. Four flight tests consisting of 8 to 9 simulation runs per flight test were performed at White Sands Space Harbor in April 1991. Three different GPS receivers were tested. The STA inertial navigation, tactical air navigation, and MSBLS sensor data were also recorded during each run. C-band radar aided laser trackers were utilized to provide the STA 'truth' trajectory.

System-Integrated Finite Element Analysis of a Full-Scale Helicopter Crash Test with Deployable Energy Absorbers

NASA Technical Reports Server (NTRS)

Annett, Martin S.; Polanco, Michael A.

2010-01-01

A full-scale crash test of an MD-500 helicopter was conducted in December 2009 at NASA Langley's Landing and Impact Research facility (LandIR). The MD-500 helicopter was fitted with a composite honeycomb Deployable Energy Absorber (DEA) and tested under vertical and horizontal impact velocities of 26-ft/sec and 40-ft/sec, respectively. The objectives of the test were to evaluate the performance of the DEA concept under realistic crash conditions and to generate test data for validation of a system integrated finite element model. In preparation for the full-scale crash test, a series of sub-scale and MD-500 mass simulator tests was conducted to evaluate the impact performances of various components, including a new crush tube and the DEA blocks. Parameters defined within the system integrated finite element model were determined from these tests. The objective of this paper is to summarize the finite element models developed and analyses performed, beginning with pre-test predictions and continuing through post-test validation.

LS-DYNA Analysis of a Full-Scale Helicopter Crash Test

NASA Technical Reports Server (NTRS)

Annett, Martin S.

2010-01-01

A full-scale crash test of an MD-500 helicopter was conducted in December 2009 at NASA Langley's Landing and Impact Research facility (LandIR). The MD-500 helicopter was fitted with a composite honeycomb Deployable Energy Absorber (DEA) and tested under vertical and horizontal impact velocities of 26 ft/sec and 40 ft/sec, respectively. The objectives of the test were to evaluate the performance of the DEA concept under realistic crash conditions and to generate test data for validation of a system integrated LS-DYNA finite element model. In preparation for the full-scale crash test, a series of sub-scale and MD-500 mass simulator tests was conducted to evaluate the impact performances of various components, including a new crush tube and the DEA blocks. Parameters defined within the system integrated finite element model were determined from these tests. The objective of this paper is to summarize the finite element models developed and analyses performed, beginning with pre-test and continuing through post test validation.

Response of surge protection devices to fast rising pulses

NASA Technical Reports Server (NTRS)

Mindel, I. N.

1980-01-01

Two types of lightning protection modules incorporating leadless (pill type) Zener like devices were evaluated with regard to their ability to suppress EMP induced transients. Two series of tests were performed to evaluate the ability of these modules to react to fast rate of rise ( 1Kv/ns) transients, and the attenuation introduced and the ability to limit damped sinusoid pulses which may be induced due to an EMP resulting from a nuclear detonation.

Evaluation of a series hybrid thrust bearing at DN values to three million. 2: Fabrication and testing

NASA Technical Reports Server (NTRS)

Eusepi, M.; Winn, L. W.

1975-01-01

Results of tests made to determine the experimental performance of a series hybrid bearing are reported. The bearing consists of a 150 mm ball bearing and a centrifugally actuated, conical, fluid film bearing fitting an envelope with an outer radius of 86.4 mm (3.4 in.) and inner radius of 71 mm (2.8 in.). Tests were conducted up to 16,500 rpm, at which speed an axial load of 15,568 N (3500 lb) was safely supported by the hybrid bearing system. Through the employment of the series hybrid bearing principle, it was possible to reduce the effective ball bearing speed to approximately one-half of the shaft speed. A reduction of this magnitude should result in a tenfold increase in the ball bearing fatigue life. A successful simulation of fluid film bearing lubricant supply failure, performed repeatedly at an operating speed of 10,000 rpm, resulted in complete and smooth change over to full scale ball bearing operation when the oil supply to the fluid film bearing was discontinued. Reactivation of the fluid film supply system produced a flawless return to the original mode of hybrid operation.

Material Compatability with Threshold Limit Value Levels of Monomethyl Hydrazine

DTIC Science & Technology

1988-10-26

supply was house- compressed air conditioned by passing through a series of demisters, a hot Hopcalite catalyst bed, a reciprocating dual-tower...recorded. At the end of a test, the tubing was rinsed with methanol and dried with compressed breathing air . Cleaning the tubing material between tests had...niecessary and identify by block wbr -’Materials were evaluated for potential use as ambient air sample lines for hydrazines. Fluorinated poly- mers

The Screening and Evaluation of Experimental Antiparasitic Drugs

DTIC Science & Technology

1990-03-01

exhibited better activity than 5 analogs of artemisinin and only 2 of the 4 different 5-fluoropyrimidine analogs were active. Neither verapamil, diltiazem...Dietary Studies 17 Table III Artemisinin , Artelinic Acid, and Arteether in a 6-Day Suppressive Test 18 Table IV Artemisinin and Related Analogs in a 3...indicate antagnism. 3-DOSE MODIFIED MM TEST A series of artemisinin analogs were administered on days 3, 4 and 5 after inoculation with a regular MM

SRNL SHELF LIFE STUDIES - SCC STUDIES AT ROOM TEMPERTURE [stress corrosion cracking

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mickalonis, J.; Duffey, J.

Phase II, Series 2 corrosion testing performed by the Savannah River National Laboratory (SRNL) for the Department of Energy 3013 container has been completed. The corrosion tests are part of an integrated plan conducted jointly by Los Alamos National Laboratory and the Savannah River Site. SRNL was responsible for conducting corrosion studies in small-scale vessels to address the influence of salt composition, water loading, and type of oxide/salt contact on the relative humidity inside a 3013 container and on the resulting corrosion of Type 304L and 316L stainless steel (304L and 316L). This testing was conducted in two phases: Phasemore » I evaluated a broad spectrum of salt compositions and initial water loadings on the salt mixtures exposed to 304L and 316L and the resulting corrosion; Phase II evaluated the corrosion of 304L at specific water loadings and a single salt composition. During Phase I testing at high initial moisture levels (0.35 to 1.24 wt%)a, the roomtemperature corrosion of 304L exposed to a series of plutonium oxide/chloride salt mixtures ranged from superficial staining to pitting and stress corrosion cracking (SCC). 304L teardrop coupons that exhibited SCC were directly exposed to a mixture composed of 98 wt % PuO2, 0.9 wt % NaCl, 0.9 wt % KCl, and 0.2 wt % CaCl2. Cracking was not observed in a 316L teardrop coupon. Pitting was also observed in this environment for both 304L and 316L with depths ranging from 20 to 100 μm. Neither pitting nor SCC was observed in mixtures with a greater chloride salt concentration (5 and 28 wt%). These results demonstrated that for a corrosive solution to form a balance existed between the water loading and the salt chloride concentration. This chloride solution results from the interaction of loaded water with the hydrating CaCl2 salt. In Phase II, Series 1 tests, the SCC results were shown to be reproducible with cracking occurring in as little as 85 days. The approximate 0.5 wt% moisture level was found to result in an initial relative humidity of ~55% within the small-scale vessels. Pits were found to be associated with cracks and appeared to act as initiators for the cracking. In a vapor-space only exposure, the weld oxide, which results from the TIG closure weld used to fabricate the teardrop coupon, was also shown to be more susceptible to pitting corrosion than a surface free from weld oxide. This result has important implications for the closure weld of the 3013 inner can since the weld oxide on the can internal surface cannot be removed. The results from the Phase II, Series 2 tests further demonstrated the significance of forming a solution with a critical chloride concentration for corrosion to proceed. 304L teardrop coupons were found to corrode only by pitting with a similar oxide/salt mixture as used in Series 1 testing but with a lower water loading of 0.2 wt%, which resulted in an initial relative humidity of 35-38%. These tests ran twice as long as those for Series 1 testing. The exposure condition was also found to impact the corrosion with salt-exposed surfaces showing lower corrosion resistance. Additional analyses of the Series 2 coupons are recommended especially for determining if cracks emanate from the bottom of pits. Data generated under the 2009 3013 corrosion test plan, as was presented here, increased the understanding of the corrosion process within a sealed 3013 container. Along with the corrosion data from destructive evaluations of 3013 containers, the inner can closure weld region (ICCWR) has been identified as the most vulnerable area of the inner can where corrosion may lead to corrosive species leaking to the interior surface of the outer container, thereby jeopardizing the integrity of the 3013 container. A new corrosion plan has been designed that will characterize the corrosion at the ICCWR of 3013 DEs as well as parameters affecting this corrosion.« less

Euclidean distance and Kolmogorov-Smirnov analyses of multi-day auditory event-related potentials: a longitudinal stability study

NASA Astrophysics Data System (ADS)

Durato, M. V.; Albano, A. M.; Rapp, P. E.; Nawang, S. A.

2015-06-01

The validity of ERPs as indices of stable neurophysiological traits is partially dependent on their stability over time. Previous studies on ERP stability, however, have reported diverse stability estimates despite using the same component scoring methods. This present study explores a novel approach in investigating the longitudinal stability of average ERPs—that is, by treating the ERP waveform as a time series and then applying Euclidean Distance and Kolmogorov-Smirnov analyses to evaluate the similarity or dissimilarity between the ERP time series of different sessions or run pairs. Nonlinear dynamical analysis show that in the absence of a change in medical condition, the average ERPs of healthy human adults are highly longitudinally stable—as evaluated by both the Euclidean distance and the Kolmogorov-Smirnov test.

Enhancing emotion recognition in children with autism spectrum conditions: an intervention using animated vehicles with real emotional faces.

PubMed

Golan, Ofer; Ashwin, Emma; Granader, Yael; McClintock, Suzy; Day, Kate; Leggett, Victoria; Baron-Cohen, Simon

2010-03-01

This study evaluated The Transporters, an animated series designed to enhance emotion comprehension in children with autism spectrum conditions (ASC). n = 20 children with ASC (aged 4-7) watched The Transporters everyday for 4 weeks. Participants were tested before and after intervention on emotional vocabulary and emotion recognition at three levels of generalization. Two matched control groups of children (ASC group, n = 18 and typically developing group, n = 18) were also assessed twice without any intervention. The intervention group improved significantly more than the clinical control group on all task levels, performing comparably to typical controls at Time 2. We conclude that using The Transporters significantly improves emotion recognition in children with ASC. Future research should evaluate the series' effectiveness with lower-functioning individuals.

Spectral and cross-spectral analysis of uneven time series with the smoothed Lomb-Scargle periodogram and Monte Carlo evaluation of statistical significance

NASA Astrophysics Data System (ADS)

Pardo-Igúzquiza, Eulogio; Rodríguez-Tovar, Francisco J.

2012-12-01

Many spectral analysis techniques have been designed assuming sequences taken with a constant sampling interval. However, there are empirical time series in the geosciences (sediment cores, fossil abundance data, isotope analysis, …) that do not follow regular sampling because of missing data, gapped data, random sampling or incomplete sequences, among other reasons. In general, interpolating an uneven series in order to obtain a succession with a constant sampling interval alters the spectral content of the series. In such cases it is preferable to follow an approach that works with the uneven data directly, avoiding the need for an explicit interpolation step. The Lomb-Scargle periodogram is a popular choice in such circumstances, as there are programs available in the public domain for its computation. One new computer program for spectral analysis improves the standard Lomb-Scargle periodogram approach in two ways: (1) It explicitly adjusts the statistical significance to any bias introduced by variance reduction smoothing, and (2) it uses a permutation test to evaluate confidence levels, which is better suited than parametric methods when neighbouring frequencies are highly correlated. Another novel program for cross-spectral analysis offers the advantage of estimating the Lomb-Scargle cross-periodogram of two uneven time series defined on the same interval, and it evaluates the confidence levels of the estimated cross-spectra by a non-parametric computer intensive permutation test. Thus, the cross-spectrum, the squared coherence spectrum, the phase spectrum, and the Monte Carlo statistical significance of the cross-spectrum and the squared-coherence spectrum can be obtained. Both of the programs are written in ANSI Fortran 77, in view of its simplicity and compatibility. The program code is of public domain, provided on the website of the journal (http://www.iamg.org/index.php/publisher/articleview/frmArticleID/112/). Different examples (with simulated and real data) are described in this paper to corroborate the methodology and the implementation of these two new programs.

Conditional heteroscedasticity as a leading indicator of ecological regime shifts.

PubMed

Seekell, David A; Carpenter, Stephen R; Pace, Michael L

2011-10-01

Regime shifts are massive, often irreversible, rearrangements of nonlinear ecological processes that occur when systems pass critical transition points. Ecological regime shifts sometimes have severe consequences for human well-being, including eutrophication in lakes, desertification, and species extinctions. Theoretical and laboratory evidence suggests that statistical anomalies may be detectable leading indicators of regime shifts in ecological time series, making it possible to foresee and potentially avert incipient regime shifts. Conditional heteroscedasticity is persistent variance characteristic of time series with clustered volatility. Here, we analyze conditional heteroscedasticity as a potential leading indicator of regime shifts in ecological time series. We evaluate conditional heteroscedasticity by using ecological models with and without four types of critical transition. On approaching transition points, all time series contain significant conditional heteroscedasticity. This signal is detected hundreds of time steps in advance of the regime shift. Time series without regime shifts do not have significant conditional heteroscedasticity. Because probability values are easily associated with tests for conditional heteroscedasticity, detection of false positives in time series without regime shifts is minimized. This property reduces the need for a reference system to compare with the perturbed system.

MELDI2 Do No Harm Test Series

NASA Technical Reports Server (NTRS)

Swanson, G. T.; Santos, J. A.; White, T. R.; Bruce, W. E.; Kuhl, C. A.; Wright, H. S.

2017-01-01

Mars 2020 will fly the Mars Entry, Descent, and Landing Instrumentation II (MEDLI2) sensor suite consisting of a total of seventeen instrumented thermal sensor plugs, eight pressure transducers, two heat flux sensors, and one radiometer embedded in the thermal protection system (TPS). Of the MEDLI2 instrumentation, eleven instrumented thermal plugs and seven pressure transducers will be installed on the heatshield of the Mars 2020 vehicle while the rest will be installed on the backshell. The goal of the MEDLI2 instrumentation is to directly inform the large performance uncertainties that contribute to the design and validation of a Mars entry system. A better understanding of the entry environment and TPS performance could lead to reduced design margins enabling a greater payload mass-fraction and smaller landing ellipses. To prove that the MEDLI2 system will not degrade the performance of the Mars 2020 TPS, an Aerothermal Do No Harm (DNH) test series was designed and conducted. Like Mars 2020's predecessor, Mars Science Laboratory (MSL), the heatshield material will be Phenolic Impregnated Carbon Ablator (PICA); the Mars 2020 entry conditions are enveloped by the MSL design environments, therefore the development and qualification testing performed during MEDLI is sufficient to show that the similar MEDLI2 heatshield instrumentation will not degrade PICA performance. However, given that MEDLI did not include any backshell instrumentation, the MEDLI2 team was required to design and execute a DNH test series utilizing the backshell TPS material (SLA-561V) with the intended flight sensor suite. To meet the requirements handed down from Mars 2020, the MEDLI2 DNH test series emphasized the interaction between the MEDLI2 sensors and sensing locations with the surrounding backshell TPS and substrucutre. These interactions were characterized by performing environmental testing of four 12" by 12" test panels, which mimicked the construction of the backshell TPS and the integration of the MEDLI2 sensors as seen in Figure 1. The testing included thermal vacuum/ cycling, random vibration, shock, and arc jet testing. The test panels were fabricated by Lockheed Martin, establishing techniques that will be utilized during the Mars 2020 vehicle installation. Each test panel included one thermal sensor plug (two embedded thermocouples), one heat flux sensor, and multiple pressure port holes for evaluation. This presentation will discuss the planning and execution of the MEDLI2 DNH test series. Selected highlights and results of each environmental test will be presented, and lessons learned will be addressed that will feed forward into the planning for the MEDLI2 flight system certification testing.

Gum-compliant uncertainty propagations for Pu and U concentration measurements using the 1st-prototype XOS/LANL hiRX instrument; an SRNL H-Canyon Test Bed performance evaluation project

DOE Office of Scientific and Technical Information (OSTI.GOV)

Holland, Michael K.; O'Rourke, Patrick E.

An SRNL H-Canyon Test Bed performance evaluation project was completed jointly by SRNL and LANL on a prototype monochromatic energy dispersive x-ray fluorescence instrument, the hiRX. A series of uncertainty propagations were generated based upon plutonium and uranium measurements performed using the alpha-prototype hiRX instrument. Data reduction and uncertainty modeling provided in this report were performed by the SRNL authors. Observations and lessons learned from this evaluation were also used to predict the expected uncertainties that should be achievable at multiple plutonium and uranium concentration levels provided instrument hardware and software upgrades being recommended by LANL and SRNL are performed.

Operational overview of NASA GTE/CITE 1 airborne instrument intercomparisons - Carbon monoxide, nitric oxide, and hydroxyl instrumentation. [Global Tropospheric Experiment/Chemical Instrumentation Test and Evaluation

NASA Technical Reports Server (NTRS)

Beck, Sherwin M.; Bendura, Richard J.; Mcdougal, David S.; Hoell, James M., Jr.; Gregory, Gerald L.; Sachse, Glen W.; Hill, Gerald F.; Curfman, Howard J., Jr.; Torres, Arnold L.; Condon, Estelle P.

1987-01-01

An overview of the airborne intercomparisons of CO, NO, and OH instrumentation is presented in this first paper of the series on the NASA Global Tropospheric Experiment/Chemical Instrumentation Test and Evaluation (GTE/CITE 1). This paper provides the reader with background information about several important characteristics of the project. These include the overall objectives and approach, the measurements taken, the intercomparison protocol, aircraft platform, profiles of each aircraft flight, and the participants. A synopsis of the overall results of the CO, NO, and OH instrument intercomparisons is also included. Companion papers discuss the detailed results of the CO and NO intercomparison tests as well as pertinent scientific findings.

Turbojet engine blade damping

NASA Technical Reports Server (NTRS)

Srinivasan, A. V.; Cutts, D. G.; Sridhar, S.

1981-01-01

The potentials of various sources of nonaerodynamic damping in engine blading are evaluated through a combination of advanced analysis and testing. The sources studied include material hysteresis, dry friction at shroud and root disk interfaces as well as at platform type external dampers. A limited seris of tests was conducted to evaluate damping capacities of composite materials (B/AL, B/AL/Ti) and thermal barrier coatings. Further, basic experiments were performed on titanium specimens to establish the characteristics of sliding friction and to determine material damping constants J and n. All the tests were conducted on single blades. Mathematical models were develthe several mechanisms of damping. Procedures to apply this data to predict damping levels in an assembly of blades are developed and discussed.

Accuracy evaluation of Fourier series analysis and singular spectrum analysis for predicting the volume of motorcycle sales in Indonesia

NASA Astrophysics Data System (ADS)

Sasmita, Yoga; Darmawan, Gumgum

2017-08-01

This research aims to evaluate the performance of forecasting by Fourier Series Analysis (FSA) and Singular Spectrum Analysis (SSA) which are more explorative and not requiring parametric assumption. Those methods are applied to predicting the volume of motorcycle sales in Indonesia from January 2005 to December 2016 (monthly). Both models are suitable for seasonal and trend component data. Technically, FSA defines time domain as the result of trend and seasonal component in different frequencies which is difficult to identify in the time domain analysis. With the hidden period is 2,918 ≈ 3 and significant model order is 3, FSA model is used to predict testing data. Meanwhile, SSA has two main processes, decomposition and reconstruction. SSA decomposes the time series data into different components. The reconstruction process starts with grouping the decomposition result based on similarity period of each component in trajectory matrix. With the optimum of window length (L = 53) and grouping effect (r = 4), SSA predicting testing data. Forecasting accuracy evaluation is done based on Mean Absolute Percentage Error (MAPE), Mean Absolute Error (MAE) and Root Mean Square Error (RMSE). The result shows that in the next 12 month, SSA has MAPE = 13.54 percent, MAE = 61,168.43 and RMSE = 75,244.92 and FSA has MAPE = 28.19 percent, MAE = 119,718.43 and RMSE = 142,511.17. Therefore, to predict volume of motorcycle sales in the next period should use SSA method which has better performance based on its accuracy.

Evaluation of the micro-carburetor

NASA Technical Reports Server (NTRS)

Weiss, M. F.; Hall, R. A.; Mazor, S. D.

1981-01-01

A prototype sonic, variable-venturi automotive carburetor was evaluated for its effects on vehicle performance, fuel economy, and exhaust emissions. A 350 CID Chevrolet Impala vehicle was tested on a chassis dynamometer over the 1975 Federal Test Procedure, urban driving cycle. The Micro-carburetor was tested and compared with stock and modified-stock engine configurations. Subsequently, the test vehicle's performance characteristics were examined with the stock carburetor and again with the Micro-carburetor in a series of on-road driveability tests. The test engine was then removed from the vehicle and installed on an engine dynamometer. Engine tests were conducted to compare the fuel economy, thermal efficiency, and cylinder-to-cylinder mixture distribution of the Micro-carburetor to that of the stock configuration. Test results show increases in thermal efficiency and improvements in fuel economy at all test conditions. Improve fuel/air mixture preparation is implied from the information presented. Further improvements in fuel economy and exhaust emissions are possible through a detailed recalibration of the Micro-carburetor.

An evaluation of grease-type ball bearing lubricants operation in various environments

NASA Technical Reports Server (NTRS)

Mcmurtrey, E. L.

1983-01-01

Because many future spacecraft or space stations will require mechanisms to operate for long periods of time in environments which are adverse to most bearing lubricants, a series of tests is continuing to evaluate 38 grease type lubricants in R-4 size bearings in five different environments for a 1 year period. Four repetitions of each test are made to provide statistical samples. These tests have also been used to select four lubricants for 5 year tests in selected environments with five repetitions of each test for statistical samples. At the present time, 142 test sets have been completed and 30 test sets are underway. The three 5 year tests in (1) continuous operation and (2) start stop operation, with both in vacuum at ambient temperatures, and (3) continuous vacuum operation at 93.3 C are now completed. To date, in both the 1 year and 5 year tests, the best results in all environments have been obtained with a high viscosity index perfluoroalkylpolyether (PFPE) grease.

Liquid Hydrogen Propellant Tank Sub-Surface Pressurization with Gaseous Helium

NASA Technical Reports Server (NTRS)

Stephens, J. R.; Cartagena, W.

2015-01-01

A series of tests were conducted to evaluate the performance of a propellant tank pressurization system with the pressurant diffuser intentionally submerged beneath the surface of the liquid. Propellant tanks and pressurization systems are typically designed with the diffuser positioned to apply pressurant gas directly into the tank ullage space when the liquid propellant is settled. Space vehicles, and potentially propellant depots, may need to conduct tank pressurization operations in micro-gravity environments where the exact location of the liquid relative to the diffuser is not well understood. If the diffuser is positioned to supply pressurant gas directly to the tank ullage space when the propellant is settled, then it may become partially or completely submerged when the liquid becomes unsettled in a microgravity environment. In such case, the pressurization system performance will be adversely affected requiring additional pressurant mass and longer pressurization times. This series of tests compares and evaluates pressurization system performance using the conventional method of supplying pressurant gas directly to the propellant tank ullage, and then supplying pressurant gas beneath the liquid surface. The pressurization tests were conducted on the Engineering Development Unit (EDU) located at Test Stand 300 at NASA Marshall Space Flight Center (MSFC). EDU is a ground based Cryogenic Fluid Management (CFM) test article supported by Glenn Research Center (GRC) and MSFC. A 150 ft3 propellant tank was filled with liquid hydrogen (LH2). The pressurization system used regulated ambient helium (GHe) as a pressurant, a variable position valve to maintain flow rate, and two identical independent pressurant diffusers. The ullage diffuser was located in the forward end of the tank and was completely exposed to the tank ullage. The submerged diffuser was located in the aft end of the tank and was completely submerged when the tank liquid level was 10% or greater. The ullage diffuser tests were conducted as a baseline to evaluate the performance of the pressurization system, and the submerged diffuser tests showed how the performance of the pressurization system was compromised when the diffuser was submerged in LH2. The test results are evaluated and compared, and included in this report for various propellant tank fill levels.

Eco-friendly synthesis of novel cyanopyridine derivatives and their anticancer and PIM-1 kinase inhibitory activities.

PubMed

Abouzid, Khaled A M; Al-Ansary, Ghada H; El-Naggar, Abeer M

2017-07-07

Targeting Pim-1 kinase recently proved to be profitable for conquering cancer proliferation. In the current study, we report the design, synthesis and biological evaluation of two novel series of 2-amino cyanopyridine series (5a-g) and 2-oxocyanopyridine series (6a-g) targeting Pim-1 kinase. All of the newly synthesized compounds were evaluated for their in vitro anticancer activity against a panel of three cell lines, namely, the liver cancer cell line (HepG2), the colon cancer cell line (HCT-116) and the breast cancer cell line (MCF-7). Most of the compounds showed good to moderate anti-proliferative activity against HepG2 and HCT-116 cell lines while only few compounds showed significant cytotoxic activity against MCF-7 cell line. Further, the Pim-1 kinase inhibitory activity for the two series was evaluated where most of the tested compounds showed marked Pim-1 kinase inhibitory activity (26%-89%). Moreover, determination of the IC 50 values unraveled very potent molecules in the submicromolar range where compound 6c possessed an IC 50 value of 0.94 μM. Moreover, apoptosis studies were conducted on the most potent compound 6c to evaluate the proapoptotic potential of our compounds. Interestingly, it induced the level of active caspase 3 and boosted the Bax/Bcl2 ratio 22704 folds in comparison to the control. Finally, a molecular docking study was conducted to reveal the probable interaction with the Pim-1 kinase active site. Copyright © 2017 Elsevier Masson SAS. All rights reserved.

Evaluation of testing strategies to identify infected animals at a single round of testing within dairy herds known to be infected with Mycobacterium avium ssp. paratuberculosis.

PubMed

More, S J; Cameron, A R; Strain, S; Cashman, W; Ezanno, P; Kenny, K; Fourichon, C; Graham, D

2015-08-01

As part of a broader control strategy within herds known to be infected with Mycobacterium avium ssp. paratuberculosis (MAP), individual animal testing is generally conducted to identify infected animals for action, usually culling. Opportunities are now available to quantitatively compare different testing strategies (combinations of tests) in known infected herds. This study evaluates the effectiveness, cost, and cost-effectiveness of different testing strategies to identify infected animals at a single round of testing within dairy herds known to be MAP infected. A model was developed, taking account of both within-herd infection dynamics and test performance, to simulate the use of different tests at a single round of testing in a known infected herd. Model inputs included the number of animals at different stages of infection, the sensitivity and specificity of each test, and the costs of testing and culling. Testing strategies included either milk or serum ELISA alone or with fecal culture in series. Model outputs included effectiveness (detection fraction, the proportion of truly infected animals in the herd that are successfully detected by the testing strategy), cost, and cost-effectiveness (testing cost per true positive detected, total cost per true positive detected). Several assumptions were made: MAP was introduced with a single animal and no management interventions were implemented to limit within-herd transmission of MAP before this test. In medium herds, between 7 and 26% of infected animals are detected at a single round of testing, the former using the milk ELISA and fecal culture in series 5 yr after MAP introduction and the latter using fecal culture alone 15 yr after MAP introduction. The combined costs of testing and culling at a single round of testing increases with time since introduction of MAP infection, with culling costs being much greater than testing costs. The cost-effectiveness of testing varied by testing strategy. It was also greater at 5 yr, compared with 10 or 15 yr, since MAP introduction, highlighting the importance of early detection. Future work is needed to evaluate these testing strategies in subsequent rounds of testing as well as accounting for different herd dynamics and different levels of herd biocontainment. Copyright © 2015 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Improved Sectional Image Analysis Technique for Evaluating Fiber Orientations in Fiber-Reinforced Cement-Based Materials.

PubMed

Lee, Bang Yeon; Kang, Su-Tae; Yun, Hae-Bum; Kim, Yun Yong

2016-01-12

The distribution of fiber orientation is an important factor in determining the mechanical properties of fiber-reinforced concrete. This study proposes a new image analysis technique for improving the evaluation accuracy of fiber orientation distribution in the sectional image of fiber-reinforced concrete. A series of tests on the accuracy of fiber detection and the estimation performance of fiber orientation was performed on artificial fiber images to assess the validity of the proposed technique. The validation test results showed that the proposed technique estimates the distribution of fiber orientation more accurately than the direct measurement of fiber orientation by image analysis.

Improved Sectional Image Analysis Technique for Evaluating Fiber Orientations in Fiber-Reinforced Cement-Based Materials

PubMed Central

Lee, Bang Yeon; Kang, Su-Tae; Yun, Hae-Bum; Kim, Yun Yong

2016-01-01

The distribution of fiber orientation is an important factor in determining the mechanical properties of fiber-reinforced concrete. This study proposes a new image analysis technique for improving the evaluation accuracy of fiber orientation distribution in the sectional image of fiber-reinforced concrete. A series of tests on the accuracy of fiber detection and the estimation performance of fiber orientation was performed on artificial fiber images to assess the validity of the proposed technique. The validation test results showed that the proposed technique estimates the distribution of fiber orientation more accurately than the direct measurement of fiber orientation by image analysis. PMID:28787839

Anaphylaxis to Gelofusine confirmed by in vitro basophil activation test: a case series.

PubMed

Apostolou, E; Deckert, K; Puy, R; Sandrini, A; de Leon, M P; Douglass, J A; Rolland, J M; O'hehir, R E

2006-03-01

The plasma expander Gelofusine (succinylated gelatin) is a recognised cause of peri-operative anaphylaxis. Current diagnosis of Gelofusine sensitivity is by skin testing, a procedure that itself carries a risk of allergic reaction. We evaluated the reliability of the in vitro basophil activation test as a diagnostic assay for Gelofusine sensitivity in subjects with a clinical history highly suggestive of Gelofusine allergy. Six patients with peri-operative anaphylaxis clinically attributed to Gelofusine were skin tested to confirm sensitivity. Control subjects included three healthy subjects and five subjects allergic to a neuromuscular blocking drug, all negative on Gelofusine skin testing. Whole blood basophil activation to Gelofusine was analysed by flow cytometry for CD63 surface expression. All of the Gelofusine sensitive patients and one of the control allergic subjects showed positive basophil activation to Gelofusine. In this series of subjects, the basophil activation test for Gelofusine allergy had a sensitivity of 100% and a specificity of 87.5%. Our findings suggest that basophil activation testing is a safe and reliable in vitro assay for prediction or confirmation of Gelofusine sensitivity in patients with high clinical suspicion of Gelofusine-induced anaphylaxis.

Comparison of six methods for the detection of causality in a bivariate time series

NASA Astrophysics Data System (ADS)

Krakovská, Anna; Jakubík, Jozef; Chvosteková, Martina; Coufal, David; Jajcay, Nikola; Paluš, Milan

2018-04-01

In this comparative study, six causality detection methods were compared, namely, the Granger vector autoregressive test, the extended Granger test, the kernel version of the Granger test, the conditional mutual information (transfer entropy), the evaluation of cross mappings between state spaces, and an assessment of predictability improvement due to the use of mixed predictions. Seven test data sets were analyzed: linear coupling of autoregressive models, a unidirectional connection of two Hénon systems, a unidirectional connection of chaotic systems of Rössler and Lorenz type and of two different Rössler systems, an example of bidirectionally connected two-species systems, a fishery model as an example of two correlated observables without a causal relationship, and an example of mediated causality. We tested not only 20 000 points long clean time series but also noisy and short variants of the data. The standard and the extended Granger tests worked only for the autoregressive models. The remaining methods were more successful with the more complex test examples, although they differed considerably in their capability to reveal the presence and the direction of coupling and to distinguish causality from mere correlation.

In Situ Optical Creep Observation of Joint-Scale Tin-Silver-Copper Solder Shear Samples

NASA Astrophysics Data System (ADS)

Herkommer, Dominik; Reid, Michael; Punch, Jeff

2009-10-01

In this paper the creep behavior of lead-free 96.5Sn-3.0Ag-0.5Cu solder is evaluated. A series of creep tests at different stress/temperature and strain rate/temperature pairs has been conducted. The tests were observed in situ with a high-magnification camera system. Optical observation results are presented from selected tests, showing the occurrence of surface effects such as shear bands, voiding, and rumpling. From these observations the main deformation mechanisms were derived and compiled in terms of their dependence on the test conditions.

Interexaminer reliability in physical examination of patients with low back pain.

PubMed

Strender, L E; Sjöblom, A; Sundell, K; Ludwig, R; Taube, A

1997-04-01

Seventy-one patients with low back pain were examined by two physiotherapists (50 patients) and two physicians (21 patients). The two physiotherapists had worked together for many years, but the two physicians had not. The interexaminer reliability of the clinical tests included in the physical examination was evaluated. To evaluate the interexaminer reliability of clinical tests used in the physical examination of patients with low back pain under ideal circumstances, which was the case for the physiotherapists. Numerous clinical tests are used in the evaluation of patients with low back pain. To reach the correct diagnosis, only tests with an acceptable validity and reliability should be used. Previous studies have mainly shown low reliability. It is important that clinical tests not be rejected because of low reliability caused by differences between examiners in performance of the examination and in their definition of normal results. Two examiners, either two physiotherapists or two physicians, independently examined patients with low back pain. In approximately half of the clinical tests studied, an acceptable reliability was demonstrated. On the basis of the physiotherapists series, the reliability was acceptable for a number of clinical tests that are used in the evaluation of patients with low back pain. The results suggest that clinical tests should be standardized to a much higher degree than they are today.

Clinical time series prediction: towards a hierarchical dynamical system framework

PubMed Central

Liu, Zitao; Hauskrecht, Milos

2014-01-01

Objective Developing machine learning and data mining algorithms for building temporal models of clinical time series is important for understanding of the patient condition, the dynamics of a disease, effect of various patient management interventions and clinical decision making. In this work, we propose and develop a novel hierarchical framework for modeling clinical time series data of varied length and with irregularly sampled observations. Materials and methods Our hierarchical dynamical system framework for modeling clinical time series combines advantages of the two temporal modeling approaches: the linear dynamical system and the Gaussian process. We model the irregularly sampled clinical time series by using multiple Gaussian process sequences in the lower level of our hierarchical framework and capture the transitions between Gaussian processes by utilizing the linear dynamical system. The experiments are conducted on the complete blood count (CBC) panel data of 1000 post-surgical cardiac patients during their hospitalization. Our framework is evaluated and compared to multiple baseline approaches in terms of the mean absolute prediction error and the absolute percentage error. Results We tested our framework by first learning the time series model from data for the patient in the training set, and then applying the model in order to predict future time series values on the patients in the test set. We show that our model outperforms multiple existing models in terms of its predictive accuracy. Our method achieved a 3.13% average prediction accuracy improvement on ten CBC lab time series when it was compared against the best performing baseline. A 5.25% average accuracy improvement was observed when only short-term predictions were considered. Conclusion A new hierarchical dynamical system framework that lets us model irregularly sampled time series data is a promising new direction for modeling clinical time series and for improving their predictive performance. PMID:25534671

Use of interrupted time series analysis in evaluating health care quality improvements.

PubMed

Penfold, Robert B; Zhang, Fang

2013-01-01

Interrupted time series (ITS) analysis is arguably the strongest quasi-experimental research design. ITS is particularly useful when a randomized trial is infeasible or unethical. The approach usually involves constructing a time series of population-level rates for a particular quality improvement focus (eg, rates of attention-deficit/hyperactivity disorder [ADHD] medication initiation) and testing statistically for a change in the outcome rate in the time periods before and time periods after implementation of a policy/program designed to change the outcome. In parallel, investigators often analyze rates of negative outcomes that might be (unintentionally) affected by the policy/program. We discuss why ITS is a useful tool for quality improvement. Strengths of ITS include the ability to control for secular trends in the data (unlike a 2-period before-and-after t test), ability to evaluate outcomes using population-level data, clear graphical presentation of results, ease of conducting stratified analyses, and ability to evaluate both intended and unintended consequences of interventions. Limitations of ITS include the need for a minimum of 8 time periods before and 8 after an intervention to evaluate changes statistically, difficulty in analyzing the independent impact of separate components of a program that are implemented close together in time, and existence of a suitable control population. Investigators must also be careful not to make individual-level inferences when population-level rates are used to evaluate interventions (though ITS can be used with individual-level data). A brief description of ITS is provided, including a fully implemented (but hypothetical) study of the impact of a program to reduce ADHD medication initiation in children younger than 5 years old and insured by Medicaid in Washington State. An example of the database needed to conduct an ITS is provided, as well as SAS code to implement a difference-in-differences model using preschool-age children in California as a comparison group. Copyright © 2013 Academic Pediatric Association. Published by Elsevier Inc. All rights reserved.

Biocontamination Control for Spacesuit Garments - A Preliminary Study

NASA Technical Reports Server (NTRS)

Rhodes, Richard A.; Orndoff, Evelyne; Korona, F. Adam; Poritz, Darwin; Smith, Jelanie; Wong, Wing

2011-01-01

This paper outlines a preliminary study that was conducted to review, test, and improve on current space suit biocontamination control. Biocontamination from crew members can cause space suit damage and objectionable odors and lead to crew member health hazards. An understanding of the level of biocontamination is necessary to mitigate its effects. A series of tests were conducted with the intent of evaluating current suit materials, ground and on-orbit disinfectants, and potential commercial off-the-shelf antimicrobial materials. Included in this paper is a discussion of the test methodology, results, and analysis method.

Emulating a flexible space structure: Modeling

NASA Technical Reports Server (NTRS)

Waites, H. B.; Rice, S. C.; Jones, V. L.

1988-01-01

Control Dynamics, in conjunction with Marshall Space Flight Center, has participated in the modeling and testing of Flexible Space Structures. Through the series of configurations tested and the many techniques used for collecting, analyzing, and modeling the data, many valuable insights have been gained and important lessons learned. This paper discusses the background of the Large Space Structure program, Control Dynamics' involvement in testing and modeling of the configurations (especially the Active Control Technique Evaluation for Spacecraft (ACES) configuration), the results from these two processes, and insights gained from this work.

Experimental and analytical studies of advanced air cushion landing systems

NASA Technical Reports Server (NTRS)

Lee, E. G. S.; Boghani, A. B.; Captain, K. M.; Rutishauser, H. J.; Farley, H. L.; Fish, R. B.; Jeffcoat, R. L.

1981-01-01

Several concepts are developed for air cushion landing systems (ACLS) which have the potential for improving performance characteristics (roll stiffness, heave damping, and trunk flutter), and reducing fabrication cost and complexity. After an initial screening, the following five concepts were evaluated in detail: damped trunk, filled trunk, compartmented trunk, segmented trunk, and roll feedback control. The evaluation was based on tests performed on scale models. An ACLS dynamic simulation developed earlier is updated so that it can be used to predict the performance of full-scale ACLS incorporating these refinements. The simulation was validated through scale-model tests. A full-scale ACLS based on the segmented trunk concept was fabricated and installed on the NASA ACLS test vehicle, where it is used to support advanced system development. A geometrically-scaled model (one third full scale) of the NASA test vehicle was fabricated and tested. This model, evaluated by means of a series of static and dynamic tests, is used to investigate scaling relationships between reduced and full-scale models. The analytical model developed earlier is applied to simulate both the one third scale and the full scale response.

Performance evaluation of DAAF as a booster material using the onionskin test

DOE Office of Scientific and Technical Information (OSTI.GOV)

Morris, John S; Francois, Elizabeth G; Hooks, Daniel E

Initiation of insensitive high explosive (IHE) formulations requires the use of a booster explosive in the initiation train. Booster material selection is crucial, as the initiation must reliably function across some spectrum of physical parameters. The interest in Diaminoazoxyfurazan (DAAF) for this application stems from the fact that it possesses many traits of an IHE but is shock sensitive enough to serve as an explosive booster. A hemispherical wave breakout test, termed the onionskin test, is one of the methods used to evaluate the performance of a booster material. The wave breakout time-position history at the surface of a hemisphericalmore » IHE charge is recorded and the relative uniformity of the breakout can be quantitatively compared between booster materials. A series of onionskin tests were performed to investigate breakout and propagation diaminoazoxyfurazan (DAAF) at low temperatures to evaluate ignition and detonation spreading in comparison to other explosives commonly used in booster applications. Some wave perturbation was observed with the DAAF booster in the onionskin tests presented. The results of these tests will be presented and discussed.« less

Laboratory Performance Evaluation Report of SEL 421 Phasor Measurement Unit

DOE Office of Scientific and Technical Information (OSTI.GOV)

Huang, Zhenyu; faris, Anthony J.; Martin, Kenneth E.

2007-12-01

PNNL and BPA have been in close collaboration on laboratory performance evaluation of phasor measurement units for over ten years. A series of evaluation tests are designed to confirm accuracy and determine measurement performance under a variety of conditions that may be encountered in actual use. Ultimately the testing conducted should provide parameters that can be used to adjust all measurements to a standardized basis. These tests are performed with a standard relay test set using recorded files of precisely generated test signals. The test set provides test signals at a level and in a format suitable for input tomore » a PMU that accurately reproduces the signals in both signal amplitude and timing. Test set outputs are checked to confirm the accuracy of the output signal. The recorded signals include both current and voltage waveforms and a digital timing track used to relate the PMU measured value with the test signal. Test signals include steady-state waveforms to test amplitude, phase, and frequency accuracy, modulated signals to determine measurement and rejection bands, and step tests to determine timing and response accuracy. Additional tests are included as necessary to fully describe the PMU operation. Testing is done with a BPA phasor data concentrator (PDC) which provides communication support and monitors data input for dropouts and data errors.« less

Advanced software development workstation. Knowledge base design: Design of knowledge base for flight planning application

NASA Technical Reports Server (NTRS)

Izygon, Michel E.

1992-01-01

The development process of the knowledge base for the generation of Test Libraries for Mission Operations Computer (MOC) Command Support focused on a series of information gathering interviews. These knowledge capture sessions are supporting the development of a prototype for evaluating the capabilities of INTUIT on such an application. the prototype includes functions related to POCC (Payload Operation Control Center) processing. It prompts the end-users for input through a series of panels and then generates the Meds associated with the initialization and the update of hazardous command tables for a POCC Processing TLIB.

Assessment of a Point-of-Use Ultrafiltration System for Turbidity and Microbial Pathogen Removal

EPA Science Inventory

U.S. EPA’s Office of Research and Development has been evaluating the performance of point-of-use (POU) devices designed for use in homes and small businesses for many years. In collaboration with the University of Cincinnati, a series of pilot-scale tests were conducted on a Mat...

Xenopus laevis Müllerian ducts are sensitive indicators of estrogenic or androgenic chemical exposure in vivo (poster presentation)

EPA Science Inventory

The Larval Amphibian Growth and Development Assay (LAGDA) is one of a series of Tier 2 test guidelines developed by the US EPA under the Endocrine Disruptor Screening Program. The LAGDA was designed to evaluate effects on growth, thyroid-mediated amphibian metamorphosis and repr...

Xenopus laevis Müllerian ducts are sensitive indicators of estrogenic or androgenic chemical exposure in vivo

EPA Science Inventory

The Larval Amphibian Growth and Development Assay (LAGDA) is one of a series of Tier 2 test guidelines being developed by the US EPA under the Endocrine Disruptor Screening Program. The LAGDA was designed to evaluate effects of lower-dose, longer-term chemical exposure on (a) am...

Optimal Rating Procedures and Methodology for NAEP Open- Ended Items. Working Paper Series.

ERIC Educational Resources Information Center

Patz, Richard J.; Wilson, Mark; Hoskens, Machteld

The National Assessment of Educational Progress (NAEP) collects data in the form of repeated, discrete measures (test items) with hierarchical structure for both measures and subjects, that is complex by any standard. This complexity has been managed through a "divide and conquer" approach of isolating and evaluating sources of…

Development of Measures of Organizational Leadership for Health Promotion

ERIC Educational Resources Information Center

Barrett, Linda; Plotnikoff, Ronald C.; Raine, Kim; Anderson, Donna

2005-01-01

This study describes the development and psychometric evaluation of four scales measuring leadership for health promotion at an organizational level in the baseline survey (n = 144) of the Alberta Heart Health Project. Content validity was established through a series of focus groups and expert opinion appraisals, pilot testing of a draft based on…

Role Taking Ability, Nonverbal Sensitivity, Language and Social Adjustment of Deaf Adolescents.

ERIC Educational Resources Information Center

Weisel, Amatzia; Bar-Lev, Hagit

1992-01-01

Presents study results regarding the social cognitive abilities of deaf adolescents. Explains that role taking ability and nonverbal sensitivity was evaluated in a series of tests. Reports low performance in social cognitive abilities. Suggests that language plays a role in social adjustment. Concludes that nonverbal sensitivity is an important…

Integrating Pharmacology Topics in High School Biology and Chemistry Classes Improves Performance

ERIC Educational Resources Information Center

Schwartz-Bloom, Rochelle D.; Halpin, Myra J.

2003-01-01

Although numerous programs have been developed for Grade Kindergarten through 12 science education, evaluation has been difficult owing to the inherent problems conducting controlled experiments in the typical classroom. Using a rigorous experimental design, we developed and tested a novel program containing a series of pharmacology modules (e.g.,…

The Socio-Scientific Reasoning Model: Instruments for Evaluation.

ERIC Educational Resources Information Center

Cheu, Janey; And Others

The Environmental Issues Test (EIT) is an instrument designed to assess moral and ethical reasoning within a scientific or technological context. It is comprised of five dilemma stories each of which highlights an environmental issue and the moral conflicts inherent in that issue. Following each dilemma story is a series of 12 issues statements,…

Smoothing Forecasting Methods for Academic Library Circulations: An Evaluation and Recommendation.

ERIC Educational Resources Information Center

Brooks, Terrence A.; Forys, John W., Jr.

1986-01-01

Circulation time-series data from 50 midwest academic libraries were used to test 110 variants of 8 smoothing forecasting methods. Data and methodologies and illustrations of two recommended methods--the single exponential smoothing method and Brown's one-parameter linear exponential smoothing method--are given. Eight references are cited. (EJS)

Assessment of a Point-of-Use Ultrafiltration System for Turbidity and Microbial Pathogen Removal

EPA Science Inventory

U.S. EPA’s Office of Research and Development has been evaluating the performance of point-of-use (POU) devices designed for use in homes and small businesses for many years. In collaboration with the University of Cincinnati, a series of pilot-scale tests were conducted on a Ma...

Literature Review and Evaluation of Solid Sorbents for Water Sampling of Explosives

DTIC Science & Technology

1981-03-01

80-054. Denboske, J.V. (1981), personal communication, Johns Manville , Denver, CO. Gallant, R.F.; J.W. King, P.L. Kevins, and J.F. Piecewicz (1978...Testing and Materials, Philadelphia, PA, STP 686, 275-290. Johns - Manville (1980), "Chromosorbc century series porous polymer supports," product brochure no

Nuclear Power: The Fifth Horseman. Worldwatch Paper 6.

ERIC Educational Resources Information Center

Hayes, Denis

This publication is the sixth in a series of papers on global environmental issues. This paper evaluates the future of nuclear power, subjecting it to several tests: (1) economics; (2) safety; (3) adequacy of fuel supplies; (4) environmental impact; and (5) both national and international security. Section headings include: (1) The nuclear fuel…

Annual baseflow variations as influenced by climate variability and agricultural land use change in the Missouri River basin

USDA-ARS?s Scientific Manuscript database

Detection of changes (steady or abrupt) in long time series of hydrological data is important for effective planning and management of water resources. This study evaluated trends in baseflow and precipitation in the Missouri River Basin (MORB) using a modified Mann-Kendall (MK) test. Precipitation ...

Integrated research in constitutive modelling at elevated temperatures, part 2

NASA Technical Reports Server (NTRS)

Haisler, W. E.; Allen, D. H.

1986-01-01

Four current viscoplastic models are compared experimentally with Inconel 718 at 1100 F. A series of tests were performed to create a sufficient data base from which to evaluate material constants. The models used include Bodner's anisotropic model; Krieg, Swearengen, and Rhode's model; Schmidt and Miller's model; and Walker's exponential model.

The NLM evaluation lecture series: introduction to the special section on evaluating health communication programs.

PubMed

Logan, Robert A; Kreps, Gary L

2014-12-01

This article introduces the Journal of Health Communication's special section, Evaluating Health Communication Programs. This special section is based on a public lecture series supported by the National Library of Medicine titled "Better Health: Evaluating Health Communication Programs" designed to share best practices for using evaluation research to develop, implement, refine, and institutionalize the best health communication programs for promoting public health. This introduction provides an overview to the series, summarizes the major presentations in the series, and describe implications from the series for translational health communication research, interventions, and programs that can enhance health outcomes.

Quantitative Characterization Guidelines of Erionite Series Minerals for Regulatory Agencies

NASA Astrophysics Data System (ADS)

Dogan, A.; Dogan, M.

2013-05-01

Erionite is a major health problem where contaminates an environment, which human population exists. Erionite - mesothelioma relationship was first observed in Turkey in 1980's and now the problem is emerging in other places in the world including Mexico. In the past, there have been in vivo or in vitro biological experiments performed using "not correctly characterized" erionite minerals. In addition, in 1997, the erionite was elevated to series status and new erionite minerals - erionite-Na, -K, -Ca - have been proposed. In 2008, erionite characterization guidelines have been proposed (Dogan and Dogan, 2008) and using these criteria, published data was re-evaluated and re-classified; and new mean chemical formula of erionite-Na, -K, -Ca was proposed. If data do not pass the E% and Mg-tests, then any reference to them in the literature is proposed to be disregarded. In some cases, different results have been reported for erionites from the same location by different authors. In these cases, if data do pass both tests but are characterized as from more than one type of erionite, then the mineral should be classified as "undifferentiated" until further clarification. Therefore, we propose (i) Erionite should be correctly characterized using proposed "positive" identification guidelines. (ii) Erionite species (whether it is -Na or -K or -Ca) should be correctly identified. (iii) There should be a close collaboration between medical community researchers and mineralogists in this field so that animal and cell experiments should be performed only with minerals that have passed "positive" identification tests. (iv) An international data bank should be established at one of the mineralogical societies and new data must be evaluated rigorously before being accepted. (v) Regulatory Agencies should ensure that the proposed guidelines for "positive" identification of erionite series minerals, both for a single fiber and a bulk mineral, are followed closely. (vi) Finally, the erionite series minerals - the most carcinogenic minerals known - require a special attention from the mineralogical community, which is a prerequisite to establish their true carcinogenic properties. References: Dogan, A.U., Baris, Y.I., Dogan, M., Emri, S., Steel, I., Elmishad, A.G., and Carbone, M., 2006. Genetic predisposition to fiber carcinogenesis causes a mesothelioma epidemic in Turkey. Cancer Research, v. 66 (10), p. 5063-5068, this research paper is highlighted in Nature Reviews-Cancer, v. 6, p. 489. Dogan, A.U. and Dogan, M., 2008, Re-evaluation and re-classification of erionite series minerals, Environmental Geochemistry and Health, v. 30, p. 355-366. Dogan, A.U., Dogan, M., and Hoskins, J.A. 2008, Erionite series minerals: Mineralogical and carcinogenic properties, Environmental Geochemistry and Health, v. 30, p. 367-381.

Fragmentation of Solid Materials Using Shock Tubes. Part 1: First Test Series in a Small Diameter Shock Tube

DTIC Science & Technology

2017-01-01

time histories with peak pressures of approximately 250 psi and 500 psi. 1.2 TESTING OBJECTIVES The first goal of this test series was to explore how...finally the late- time at-rest fragments were physically collected and analyzed post-test. Because this test series physically collected over 50,000...for a single fragmenting object. Comparing the three measurement techniques used in this test series , the late- time physically- collected mass

In-orbit evaluation of the control system/structural mode interactions of the OSO-8 spacecraft

NASA Technical Reports Server (NTRS)

Slafer, L. I.

1979-01-01

The Orbiting Solar Observatory-8 experienced severe structural mode/control loop interaction problems during the spacecraft development. Extensive analytical studies, using the hybrid coordinate modeling approach, and comprehensive ground testing were carried out in order to achieve the system's precision pointing performance requirements. A recent series of flight tests were conducted with the spacecraft in which a wide bandwidth, high resolution telemetry system was utilized to evaluate the on-orbit flexible dynamics characteristics of the vehicle along with the control system performance. The paper describes the results of these tests, reviewing the basic design problem, analytical approach taken, ground test philosophy, and on-orbit testing. Data from the tests was used to determine the primary mode frequency, damping, and servo coupling dynamics for the on-orbit condition. Additionally, the test results have verified analytically predicted differences between the on-orbit and ground test environments, and have led to a validation of both the analytical modeling and servo design techniques used during the development of the control system.

An evaluation of grease type ball bearing lubricants operating in various environments

NASA Technical Reports Server (NTRS)

Mcmurtrey, E. L.

1984-01-01

Because many future spacecraft or space stations will require mechanisms to operate for long periods of time in environments which are adverse to most bearing lubricants, a series of tests has been completed to evaluate 38 grease type lubricants in R-4 size bearings in five different environments for a 1 year period. Four repetitions of each test were made to provide statistical samples. These tests were also used to select four lubricants for 5 year tests in selected environments with five repetitions of each test for statistical samples. In this completed program, 172 test sets have been completed. The three 5 year tests in: (1) continuous operation and (2) start stop operation, with both in vacuum at ambient temperatures, and (3) continuous vacuum operation at 93.3 C have been completed. In both the 1 year and 5 year tests, the best results in all environments have been obtained with a high viscosity index perfluoroalkylpolyether (PFPE) grease.

Diabetes Training for Community Health Workers.

PubMed

Aponte, Judith

2015-12-01

A 2.5-month diabetes education training for community health workers (CHWs) was developed, implemented, and evaluated. Training methods used included case studies, role-playing, and lectures. Exams were used throughout the training for its evaluation. Teaching was delivered by different ways: a one day American Diabetes Association (ADA) course; a five day Diabetes Self-Management Program (DSMP); Conversation Maps; and a series of seven National Institute of Diabetes and Digestive and Kidney Diseases (NIDDK) diabetes education booklets. Qualitative and quantitative evaluative methods were used during and after the training. The CHWs' diabetes knowledge was evaluated by a pre- and post-test Diabetes Knowledge Questionnaire (DKQ). The post-test was conducted one week after completing the training. The findings showed that the diabetes knowledge of the CHWs increased. Diabetes competencies and evaluative tools need to be developed specific for CHWs as a way to standardize all CHW diabetes trainings.

A Formative Evaluation of Me Now, Unit I, Digestion and Circulation, Life Sciences for the Educable Mentally Handicapped Intermediate Grades (11-13 years).

ERIC Educational Resources Information Center

Robinson, James T.; Tolman, Richard R.

In order to evaluate Unit I (Digestion and Circulation) of the Me Now series of Life Sciences for the Educable Mentally Handicapped, 139 students in an experimental group (mean IQ 72.04; mean CA 144.9 months) and 154 control subjects (mean IQ 70.2; mean CA 148.3 months) were pre- and post-tested following instruction in the Me Now series…

Blended-Wing-Body Low-Speed Flight Dynamics: Summary of Ground Tests and Sample Results

NASA Technical Reports Server (NTRS)

Vicroy, Dan D.

2009-01-01

A series of low-speed wind tunnel tests of a Blended-Wing-Body tri-jet configuration to evaluate the low-speed static and dynamic stability and control characteristics over the full envelope of angle of attack and sideslip are summarized. These data were collected for use in simulation studies of the edge-of-the-envelope and potential out-of-control flight characteristics. Some selected results with lessons learned are presented.

Expedient Spall Repair Methods and Equipment for Airfield Pavements Preprint

DTIC Science & Technology

2009-08-01

placement (3). RESEACH OBJECTIVES AND SCOPE The objective of this research was to develop one or more methods that will allow field personnel to...cores were used to perform in-situ tensile pull-off tests to evaluate the bond between the repair material and the substrate. Also, a series of 4...inch diameters cores were cut, and direct shear tests were performed on the repair material/substrate interface. Finally, all spalls were trafficked for

ATD-1 Avionics Phase 2 Flight Test: Flight Test Operations and Saftey Report (FTOSR)

NASA Technical Reports Server (NTRS)

Boyle, Dan; Rein-Weston, Karl; Berckefeldt, Rick; Eggling, Helmuth; Stankiewicz, Craig; Silverman, George

2017-01-01

The Air Traffic Management Technology Demonstration-1 (ATD-1) is a major applied research and development activity of NASA's Airspace Operations and Safety Program (AOSP). The demonstration is the first of an envisioned series of Air Traffic Management (ATM) Technology Demonstration sub-projects that will demonstrate innovative NASA technologies that have attained a sufficient level of maturity to merit more in-depth research and evaluation at the system level in relevant environments.

Test methods for optical disk media characteristics (for 356 mm ruggedized magneto-optic media)

NASA Technical Reports Server (NTRS)

Podio, Fernando L.

1991-01-01

Standard test methods for computer storage media characteristics are essential and allow for conformance to media interchange standards. The test methods were developed for 356 mm two-sided laminated glass substrate with a magneto-optic active layer media technology. These test methods may be used for testing other media types, but in each case their applicability must be evaluated. Test methods are included for a series of different media characteristics, including operational, nonoperational, and storage environments; mechanical and physical characteristics; and substrate, recording layer, and preformat characteristics. Tests for environmental qualification and media lifetimes are also included. The best methods include testing conditions, testing procedures, a description of the testing setup, and the required calibration procedures.

SRB Materials and Processes Assessment from Laboratory and Ocean Environmental Tests

NASA Technical Reports Server (NTRS)

1978-01-01

The Materials and Processes Laboratory evaluation of Solid Rocket Boosters (SRB) and Solid Rocket Motors (SRM) candidate material, both in-house and with ocean exposure tests at Panama City and Kennedy Space Center (KSC), Florida is presented. Early sample tests showed excellent seawater corrosion resistance for inconel 718 and titanium 6A1-4V alloys. Considerable corrosion and biofouling occurred with bare 2219-T87 aluminum. Subsequent tests conclusively demonstrated that epoxy coatings prevented corrosion of 2219-T87 aluminum as long as the coatings stays intact. The results and assessment of the series of ocean environmental tests that were conducted are also presented.

Testing of a Stitched Composite Large-Scale Multi-Bay Pressure Box

NASA Technical Reports Server (NTRS)

Jegley, Dawn; Rouse, Marshall; Przekop, Adam; Lovejoy, Andrew

2016-01-01

NASA has created the Environmentally Responsible Aviation (ERA) Project to develop technologies to reduce aviation's impact on the environment. A critical aspect of this pursuit is the development of a lighter, more robust airframe to enable the introduction of unconventional aircraft configurations. NASA and The Boeing Company have worked together to develop a structural concept that is lightweight and an advancement beyond state-of-the-art composite structures. The Pultruded Rod Stitched Efficient Unitized Structure (PRSEUS) is an integrally stiffened panel design where elements are stitched together. The PRSEUS concept is designed to maintain residual load carrying capabilities under a variety of damage scenarios. A series of building block tests were evaluated to explore the fundamental assumptions related to the capability and advantages of PRSEUS panels. The final step in the building block series is an 80%-scale pressure box representing a portion of the center section of a Hybrid Wing Body (HWB) transport aircraft. The testing of this article under maneuver load and internal pressure load conditions is the subject of this paper. The experimental evaluation of this article, along with the other building block tests and the accompanying analyses, has demonstrated the viability of a PRSEUS center body for the HWB vehicle. Additionally, much of the development effort is also applicable to traditional tube-and-wing aircraft, advanced aircraft configurations, and other structures where weight and through-the-thickness strength are design considerations.

Mortality among military participants at the 1957 PLUMBBOB nuclear weapons test series and from leukemia among participants at the SMOKY test.

PubMed

Caldwell, Glyn G; Zack, Matthew M; Mumma, Michael T; Falk, Henry; Heath, Clark W; Till, John E; Chen, Heidi; Boice, John D

2016-09-01

Health effects following low doses of ionizing radiation are uncertain. Military veterans at the Nevada test site (NTS) during the SMOKY atmospheric nuclear weapons test in 1957 were reported to be at increased risk for leukemia in 1979, but this increase was not evaluated with respect to radiation dose. The SMOKY test was one of 30 tests in 1957 within the PLUMBBOB test series. These early studies led to public laws where atomic veterans could qualify for compensation for presumptive radiogenic diseases. A retrospective cohort study was conducted of 12219 veterans at the PLUMBBOB test series, including 3020 at the SMOKY nuclear test. Mortality follow-up was through 2010 and observed causes of death were compared with expected causes based on general population rates. Radiation dose to red bone marrow was based on individual dose reconstructions, and Cox proportional hazards models were used to evaluate dose response for all leukemias other than chronic lymphocytic leukemia (non-CLL leukemia). Vital status was determined for 95.3% of the 12 219 veterans. The dose to red bone marrow was low (mean 3.2 mGy, maximum 500 mGy). Military participants at the PLUMBBOB nuclear test series remained relatively healthy after 53 years and died at a lower rate than the general population. In contrast, and in comparison with national rates, the SMOKY participants showed significant increases in all causes of death, respiratory cancer, leukemia, nephritis and nephrosis, and accidents, possibly related in part to lifestyle factors common to enlisted men who made up 81% of the SMOKY cohort. Compared with national rates, a statistically significant excess of non-CLL leukemia was observed among SMOKY participants (Standardized Mortality Ratio  =  1.89, 95% 1.24-2.75, n  =  27) but not among PLUMBBOB participants after excluding SMOKY (SMR  =  0.87, 95% 0.64-1.51, n  =  47). Leukemia risk, initially reported to be significantly increased among SMOKY participants, remained elevated, but this risk diminished over time. Despite an intense dose reconstruction, the risk for leukemia was not found to increase with increasing levels of radiation dose to the red bone marrow. Based on a linear model, the estimated excess relative risk per mGy is  -0.05 (95% CI -0.14, 0.04). An explanation for the observed excess of leukemia remains unresolved but conceivably could be related to chance due to small numbers, subtle biases in the study design and/or high tobacco use among enlisted men. Larger studies should elucidate further the possible relationship between fallout radiation, leukemia and cancer among atomic veterans.

Mortality among Military Participants at the 1957 PLUMBBOB Nuclear Weapons Test Series and on Leukemia among Participants at the SMOKY Test

PubMed Central

Caldwell, Glyn G.; Zack, Matthew M.; Mumma, Michael T.; Falk, Henry; Heath, Clark W.; Till, John E.; Chen, Heidi; Boice, John D.

2016-01-01

Health effects following low doses of ionizing radiation are uncertain. Military veterans at the Nevada Test Site (NTS) during the SMOKY atmospheric nuclear weapons test in 1957 were reported to be at increased risk for leukemia in 1979, but this increase was not evaluated with respect to radiation dose. The SMOKY test was one of 30 tests in 1957 within the PLUMBBOB test series. These early studies led to public laws where atomic veterans could qualify for compensation for presumptive radiogenic diseases. A retrospective cohort study was conducted of 12,219 veterans at PLUMBBOB test series, including 3,020 at the SMOKY nuclear test. Mortality follow-up was through 2010 and observed causes of death were compared with expected causes based on general population rates. Radiation dose to red bone marrow was based on individual dose reconstructions, and Cox proportional hazards models were used to evaluate dose response for all leukemias other than chronic lymphocytic leukemia (non-CLL leukemia). Vital status was determined for 95.3% of the 12,219 veterans. The dose to red bone marrow was low (mean 3.2 mGy, maximum 500 mGy). Military participants at the PLUMBBOB nuclear test series remained relatively healthy after 53 years and died at a lower rate than the general population. In contrast, and in comparison with national rates, the SMOKY participants showed significant increases in all causes of death, respiratory cancer, leukemia, nephritis and nephrosis, and accidents, possibly related in part to lifestyle factors common to enlisted men who made up 81% of the SMOKY cohort. Compared with national rates, a statistically significant excess of non-CLL leukemia was observed among SMOKY participants (Standardized Mortality Ratio=1.89, 95% 1.24–2.75, n=27) but not among PLUMBBOB participants after excluding SMOKY (SMR=0.87, 95% 0.64–1.51, n=47). Leukemia risk, initially reported to be significantly increased among SMOKY participants, remained elevated, but this risk diminished over time. Despite an intense dose reconstruction, the risk for leukemia was not found to increase with increasing levels of radiation dose to the red bone marrow. Based on a linear model, the estimated excess relative risk per mGy is −0.05 (95% CI −0.14, 0.04). An explanation for the observed excess of leukemia remains unresolved but conceivably could be related to chance due to small numbers, subtle biases in the study design and/or high tobacco use among enlisted men. Larger studies should elucidate further the possible relationship between fallout radiation, leukemia and cancer among atomic veterans. PMID:27355245

Analytical and Experimental Evaluation of Digital Control Systems for the Semi-Span Super-Sonic Transport (S4T) Wind Tunnel Model

NASA Technical Reports Server (NTRS)

Wieseman, Carol D.; Christhilf, David; Perry, Boyd, III

2012-01-01

An important objective of the Semi-Span Super-Sonic Transport (S4T) wind tunnel model program was the demonstration of Flutter Suppression (FS), Gust Load Alleviation (GLA), and Ride Quality Enhancement (RQE). It was critical to evaluate the stability and robustness of these control laws analytically before testing them and experimentally while testing them to ensure safety of the model and the wind tunnel. MATLAB based software was applied to evaluate the performance of closed-loop systems in terms of stability and robustness. Existing software tools were extended to use analytical representations of the S4T and the control laws to analyze and evaluate the control laws prior to testing. Lessons were learned about the complex windtunnel model and experimental testing. The open-loop flutter boundary was determined from the closed-loop systems. A MATLAB/Simulink Simulation developed under the program is available for future work to improve the CPE process. This paper is one of a series of that comprise a special session, which summarizes the S4T wind-tunnel program.

Precision Tests of a Quantum Hall Effect Device DC Equivalent Circuit Using Double-Series and Triple-Series Connections

PubMed Central

Jeffery, A.; Elmquist, R. E.; Cage, M. E.

1995-01-01

Precision tests verify the dc equivalent circuit used by Ricketts and Kemeny to describe a quantum Hall effect device in terms of electrical circuit elements. The tests employ the use of cryogenic current comparators and the double-series and triple-series connection techniques of Delahaye. Verification of the dc equivalent circuit in double-series and triple-series connections is a necessary step in developing the ac quantum Hall effect as an intrinsic standard of resistance. PMID:29151768

Sensitivity of the immature rat uterotrophic assay to mixtures of estrogens.

PubMed Central

Tinwell, Helen; Ashby, John

2004-01-01

We have evaluated whether mixtures of estrogens, present in the mix at doses that are individually inactive in the immature rat uterotrophic assay, can give a uterotrophic response. Seven chemicals were evaluated: nonylphenol, bisphenol A (BPA), methoxychlor, genistein (GEN), estradiol, diethylstilbestrol, and ethinyl estradiol. Dose responses in the uterotrophic assay were constructed for each chemical. The first series of experiments involved evaluating binary mixtures of BPA and GEN at dose levels that gave moderate uterotrophic responses when tested individually. The mixtures generally showed an intermediate or reduced uterotrophic effect compared with when the components of the mixture were tested alone at the dose used in the mixture. The next series of experiments used a multicomponent (complex) mixture of all seven chemicals evaluated at doses that gave either weakly positive or inactive uterotrophic responses when tested individually in the assay. Doses that were nominally equi-uterotrophic ranged over approximately six orders of magnitude for the seven chemicals. Doses of agents that gave a weak uterotrophic response when tested individually gave a marginally enhanced positive response in the assay when tested combined as a mixture. Doses of agents that gave a negative uterotrophic response when tested individually gave a positive response when tested as a mixture. These data indicate that a variety of different estrogen receptor (ER) agonists, present individually at subeffective doses, can act simultaneously to evoke an ER-regulated response. However, translating these findings into the process of environmental hazard assessment will be difficult. The simple addition of the observed, or predicted, activities for the components of a mixture is confirmed here to be inappropriate and to overestimate the actual effect induced by the mixture. Equally, isobole analysis is only suitable for two- or three-component mixtures, and concentration addition requires access to dose-response data and EC50 values (concentration giving 50% of the maximum response) for the individual components of the mixture--requirements that will rarely be fulfilled for complex environmental samples. Given these uncertainties, we conclude that it may be most expedient to select and bioassay whole environmental mixtures of potential concern. PMID:15064164

Full-scale aircraft cabin flammability tests of improved fire-resistant materials, test series 2

NASA Technical Reports Server (NTRS)

Stuckey, R. N.; Bricker, R. W.; Kuminecz, J. F.; Supkis, D. E.

1976-01-01

Full-scale aircraft flammability tests in which the effectiveness of new fire-resistant materials was evaluated by comparing their burning characteristics with those of other fire-resistant aircraft materials were described. New-fire-resistant materials that are more economical and better suited for aircraft use than the previously tested fire-resistant materials were tested. The fuel ignition source for one test was JP-4; a smokeless fuel was used for the other test. Test objectives, methods, materials, and results are presented and discussed. The results indicate that, similar to the fire-resistant materials tested previously, the new materials decompose rather than ignite and do not support fire propagation. Furthermore, the new materials did not produce a flash fire.

Vascular endothelial growth factor monitoring in advanced hepatocellular carcinoma patients treated with radiofrequency ablation plus octreotide: a single center experience.

PubMed

Montella, L; Addeo, R; Caraglia, M; Faiola, V; Guarrasi, R; Vincenzi, B; Palmeri, A; Capasso, E; Nocera, V; Tarantino, L; Ariete, M; Martorelli, A; Del Prete, S

2008-08-01

Local therapies such as radiofrequency ablation (RFA) represent a valuable choice in limited hepatocellular carcinoma (HCC) and are increasingly used also in advanced tumors. Medical treatments generally gave frustrating results in advanced HCC especially if comorbidities exist. Several biologic non-chemotherapeutic drugs are currently tested in HCC and, among them, octreotide was evaluated in single series of HCC patients reporting conflicting results. We have treated a series of 35 patients affected by advanced HCC (26 M and 9 F; age range: 55-85 years, median: 73 years) with RFA followed by octreotide to primarily evaluate the safety of combined treatment and to give preliminary evaluation on its activity. We have also evaluated serum VEGF changes during the study. Child A and Child B represented 60% and about 34% of the cases, respectively. Only two patients with Child C compensated cirrhosis were included in this study. All patients have multiple liver HCC nodules and one had bone metastases. Two complete responses, 3 partial responses and 23 disease stabilization for at least three months were obtained (overall response rate, 14,2%; clinical benefit, 80%). Mean overall survival was 31.4 months. The combined treatment was well tolerated. Statistically significant correlation was found between serum VEGF and tumor progression. In conclusion, the combination of RFA and octreotide was active in advanced HCC, however, confirmation in a larger series is required.

Evaluation of four fast-response flow measurement devices

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gero, A.J.; Suppers, K.L.; Tomb, T.F.

1988-01-01

The Federal Mine Safety and Health Act of 1977 requires that sampling of dust in coal mine environments be conducted with an approved sampler operating at a flow rate of 2.0 liters of air per minute or at such other flow rate as prescribed by the Secretaries of Labor and of Health and Human Services. Standard procedures for calibration of these samplers within the Mine Safety and Health Administration utilize either a 3.0 liter capacity wet test meter or a 1.0 liter soap film calibrator. Several new flow calibrating devices have become commercially available. This paper describes an evaluation conductedmore » on four such devices: the Mast Model 823-2 bubble flowmeter, the Buck Calibrator, the Kurz Model 541S mass flowmeter and the Kurz Pocket Calibrator. The precision of a series of measurements made with each instrument was compared to the precision of a series of measurements made with the wet test meter. The comparison showed that the variability of calibration measurements obtained with the fast response flow calibrators was between 1.5 and 4.5 times larger than that obtained with the WTM; however, with all of the calibration devices evaluated, three repetitive measurements were sufficient to obtain a precision of {plus minus}0.1 liters per minute. 4 refs., 2 figs., 1 tab.« less

Biological diagnosis of von Willebrand disease: analytical characteristics of Innovance vWF:Ac assay kit on STA-R Evolution Expert series analyzer (Stago).

PubMed

Florin, Cécile; Garraud, Olivier; Molliex, Serge; Tardy, Brigitte; Campos, Lydia; Scherrer, Carine

2016-06-01

The Innovance VWF:Ac test (Siemens) has the particularity to assess the binding capacity of von Willebrand factor (VWF) to recombinant platelet GPIb mutated in the absence of ristocetin. Our study aimed to evaluate and validate according to standard NF EN ISO 15189 the original protocol adaptation on STA-R Evolution series analyser (Diagnostica Stago). We evaluated the performance in terms of imprecision and we validate additional parameters necessary in range B as recommended by the SH GTA 04 (Cofrac). We compared the new assay with the reference assay: ristocetin cofactor activity (VWF:RCo) performed on the BCS-XP analyser by testing retrospectively samples from 82 healthy normal subjects and 61 patients with von Willebrand disease (VWD). This new assay is consistent with objectives set in terms of imprecision with CV around 4%. Excepted limit of quantification higher, additional parameters evaluated in range B have been validated. The Innovance VWF: Ac assay allowed the detection of all deficits of VWF already detected by the VWF:RCo test on the BCS-XP. This adjustment on STA-R analyser therefore has satisfactory analytical performance criteria. Apart from the limit of quantification, this reagent can be used according to the recommendations specified in the original protocol adaptation. Its performance and compatibility with the spot measurement allow the diagnosis and therapeutic monitoring of VWD according to current requirements and guidelines.

Open stack thermal battery tests

DOE Office of Scientific and Technical Information (OSTI.GOV)

Long, Kevin N.; Roberts, Christine C.; Grillet, Anne M.

We present selected results from a series of Open Stack thermal battery tests performed in FY14 and FY15 and discuss our findings. These tests were meant to provide validation data for the comprehensive thermal battery simulation tools currently under development in Sierra/Aria under known conditions compared with as-manufactured batteries. We are able to satisfy this original objective in the present study for some test conditions. Measurements from each test include: nominal stack pressure (axial stress) vs. time in the cold state and during battery ignition, battery voltage vs. time against a prescribed current draw with periodic pulses, and images transversemore » to the battery axis from which cell displacements are computed. Six battery configurations were evaluated: 3, 5, and 10 cell stacks sandwiched between 4 layers of the materials used for axial thermal insulation, either Fiberfrax Board or MinK. In addition to the results from 3, 5, and 10 cell stacks with either in-line Fiberfrax Board or MinK insulation, a series of cell-free “control” tests were performed that show the inherent settling and stress relaxation based on the interaction between the insulation and heat pellets alone.« less

Examination of a size-change test for photovoltaic encapsulation materials

NASA Astrophysics Data System (ADS)

Miller, David C.; Gu, Xiaohong; Ji, Liang; Kelly, George; Nickel, Nichole; Norum, Paul; Shioda, Tsuyoshi; Tamizhmani, Govindasamy; Wohlgemuth, John H.

2012-10-01

We examine a proposed test standard that can be used to evaluate the maximum representative change in linear dimensions of sheet encapsulation products for photovoltaic modules (resulting from their thermal processing). The proposed protocol is part of a series of material-level tests being developed within Working Group 2 of the Technical Committee 82 of the International Electrotechnical Commission. The characterization tests are being developed to aid module design (by identifying the essential characteristics that should be communicated on a datasheet), quality control (via internal material acceptance and process control), and failure analysis. Discovery and interlaboratory experiments were used to select particular parameters for the size-change test. The choice of a sand substrate and aluminum carrier is explored relative to other options. The temperature uniformity of +/-5°C for the substrate was confirmed using thermography. Considerations related to the heating device (hot-plate or oven) are explored. The time duration of 5 minutes was identified from the time-series photographic characterization of material specimens (EVA, ionomer, PVB, TPO, and TPU). The test procedure was revised to account for observed effects of size and edges. The interlaboratory study identified typical size-change characteristics, and also verified the absolute reproducibility of +/-5% between laboratories.

Measure of viral load by using the Abbott Real-Time HIV-1 assay on dried blood and plasma spot specimens collected in 2 rural dispensaries in Cameroon.

PubMed

Mbida, André Dieudonné; Sosso, Samuel; Flori, Pierre; Saoudin, Henia; Lawrence, Philip; Monny-Lobé, Marcel; Oyono, Yves; Ndzi, Edward; Cappelli, Giulia; Lucht, Frédéric; Pozzetto, Bruno; Oukem-Boyer, Odile Ouwe Missi; Bourlet, Thomas

2009-09-01

This study aimed to evaluate the use of dried blood spots (DBSs) and dried plasma spots (DPSs) locally collected in 2 rural dispensaries in Cameroon for the quantification of HIV-1 RNA. Forty-one subjects were sampled and spots of whole blood and plasma were deposited onto Whatman 903 cards and dried at ambient temperature under local conditions. Two sets of DBS and DPS cards were done per patient. The rest of the liquid plasma (LP) was frozen until use. LPs were tested at the "Chantal Biya" International Reference Centre (Yaoundé, Cameroon) by the Abbott Real-Time HIV-1 assay (Abbott Molecular Diagnostics, Wiesbaden, Germany). One series of DBS and DPS was transported and tested between 2 and 6 weeks later at the Virology Laboratory of Saint-Etienne (France). The second series was routed by mail and tested after up to 3 months of storage at ambient temperature. From the first series, the correlation rate between viral loads obtained from LP and DBS, and from LP and DPS, was 0.98 and 0.99, respectively; specificity of DBS and DPS results was 100%. The results obtained from the second series indicate a great stability of DBS after long-term storage. This study demonstrates that DBSs collected under local conditions in resource-limited settings are suitable for the differed quantification of HIV-1 RNA.

Design, construction, operation, and evaluation of a prototype culm combustion boiler/heater unit

DOE Office of Scientific and Technical Information (OSTI.GOV)

D'Aciermo, J.; Richards, H.; Spindler, F.

1983-10-01

A process for utilizing anthracite culm in a fluidized bed combustion system was demonstrated by the design and construction of a prototype steam plant at Shamokin, PA, and operation of the plant for parametric tests and a nine month extended durability test. The parametric tests evaluated turndown capability of the plant and established turndown techniques to be used to achieve best performance. Throughout the test program the fluidized bed boiler durability was excellent, showing very high resistence to corrosion and erosion. A series of 39 parametric tests was performed in order to demonstrate turndown capabilities of the atmospheric fluidized bedmore » boiler burning anthracite culm. Four tests were performed with bituminous coal waste (called gob) which contains 4.8 to 5.5% sulfur. Heating value of both fuels is approximately 3000 Btu/lb and ash content is approximately 70%. Combustion efficiency, boiler efficiency, and emissions of NO/sub x/ and SO/sub 2/ were also determined for the tests.« less

Design, fabrication and test of graphite/polymide composite joints and attachments: Summary

NASA Technical Reports Server (NTRS)

Cushman, J. B.; Mccleskey, S. F.; Ward, S. H.

1983-01-01

The design, analysis and testing performed to develop four types of graphite/polyimide (Gr/PI) bonded and bolted composite joints for lightly loaded control surfaces on advanced space transportation systems that operate at temperatures up to 561K (550 F) are summarized. Material properties and 'small specimen' tests were conducted to establish design data and to evaluate specific design details. 'Static discriminator' tests were conducted on preliminary designs to verify structural adequacy. Scaled up specimens of the final joint designs, representative of production size requirements, were subjected to a series of static and fatigue tests to evaluate joint strength. Effects of environmental conditioning were determined by testing aged (125 hours 589K (600 F)) and thermal cycled (116K to 589K (-250 F to 600 F), 125 times) specimens. It is concluded Gr/PI joints can be designed and fabricated to carry the specified loads. Test results also indicate a possible resin loss or degradation of laminates after exposure to 589K (600 F) for 125 hours.

Design, fabrication and test of graphite/polyimide composite joints and attachments. [spacecraft control surfaces

NASA Technical Reports Server (NTRS)

Cushman, J. B.; Mccleskey, S. F.; Ward, S. H.

1982-01-01

The design, analysis, and testing performed to develop four types of graphite/polyimide (Gr/PI) bonded and bolted composite joints for lightly loaded control surfaces on advanced space transportation systems that operate at temperatures up to 561 K (550 F) are summarized. Material properties and small specimen tests were conducted to establish design data and to evaluate specific design details. Static discriminator tests were conducted on preliminary designs to verify structural adequacy. Scaled up specimens of the final joint designs, representative of production size requirements, were subjected to a series of static and fatigue tests to evaluate joint strength. Effects of environmental conditioning were determined by testing aged (125 hours at 589 K (600 F)) and thermal cycled (116 K to 589 K (-250 F to 600 F), 125 times) specimens. It is concluded Gr/PI joints can be designed and fabricated to carry the specified loads. Test results also indicate a possible resin loss or degradation of laminates after exposure to 589 K (600 F) for 125 hours.

Phase 2 STS new user development program. Volume 1: Executive summary

NASA Technical Reports Server (NTRS)

Mcdowell, J. R.

1976-01-01

A methodology for developing new users for STS other than NASA and DoD, thereby maximizing the use of the STS system was developed. The approach to user development, reflected in the implementation plan, and attendant informational material to be used were evaluated by conducting a series of test cases with selected user organizations. These test case organizations were, in effect, used as consultants to evaluate the effectiveness, the needs, the completeness, and the adequacy of the user development approach and informational material. The selection of the test cases provided a variety of potential STS users covering industry, other government agencies, and the educational sector. The test cases covered various use areas and provided a mix of user organization types. A summary of the actual test cases conducted is given. The conduct of the test cases verified the general approach of the implementation plan, the validity of the user development strategy prepared for each test case organization and the effectiveness of the STS basic and user customized informational material.

Test selection, adaptation, and evaluation: a systematic approach to assess nutritional influences on child development in developing countries.

PubMed

Prado, Elizabeth L; Hartini, Sri; Rahmawati, Atik; Ismayani, Elfa; Hidayati, Astri; Hikmah, Nurul; Muadz, Husni; Apriatni, Mandri S; Ullman, Michael T; Shankar, Anuraj H; Alcock, Katherine J

2010-03-01

Evaluating the impact of nutrition interventions on developmental outcomes in developing countries can be challenging since most assessment tests have been produced in and for developed country settings. Such tests may not be valid measures of children's abilities when used in a new context. We present several principles for the selection, adaptation, and evaluation of tests assessing the developmental outcomes of nutrition interventions in developing countries where standard assessment tests do not exist. We then report the application of these principles for a nutrition trial on the Indonesian island of Lombok. Three hundred children age 22-55 months in Lombok participated in a series of pilot tests for the purpose of test adaptation and evaluation. Four hundred and eighty-seven 42-month-old children in Lombok were tested on the finalized test battery. The developmental assessment tests were adapted to the local context and evaluated for a number of psychometric properties, including convergent and discriminant validity, which were measured based on multiple regression models with maternal education, depression, and age predicting each test score. The adapted tests demonstrated satisfactory psychometric properties and the expected pattern of relationships with the three maternal variables. Maternal education significantly predicted all scores but one, maternal depression predicted socio-emotional competence, socio-emotional problems, and vocabulary, while maternal age predicted socio-emotional competence only. Following the methodological principles we present resulted in tests that were appropriate for children in Lombok and informative for evaluating the developmental outcomes of nutritional supplementation in the research context. Following this approach in future studies will help to determine which interventions most effectively improve child development in developing countries.

Synthesis and biological evaluation of potential acetylcholinesterase inhibitors based on a benzoxazine core.

PubMed

Méndez-Rojas, Claudio; Quiroz, Gabriel; Faúndez, Mario; Gallardo-Garrido, Carlos; Pessoa-Mahana, C David; Chung, Hery; Gallardo-Toledo, Eduardo; Saitz-Barría, Claudio; Araya-Maturana, Ramiro; Kogan, Marcelo J; Zúñiga-López, María C; Iturriaga-Vásquez, Patricio; Valenzuela-Gutiérrez, Carla; Pessoa-Mahana, Hernán

2018-05-01

With the purpose of expanding the structural variety of chemical compounds available as pharmacological tools for the treatment of Alzheimer's disease, we synthesized and evaluated a novel series of indole-benzoxazinones (Family I) and benzoxazine-arylpiperazine derivatives (Family II) for potential human acetylcholinesterase (hAChE) inhibitory properties. The most active compounds 7a and 7d demonstrated effective inhibitory profiles with K i values of 20.3 ± 0.9 μM and 20.2 ± 0.9 μM, respectively. Kinetic inhibition assays showed non-competitive inhibition of AChE by the tested compounds. According to our docking studies, the most active compounds from both series (Families I and II) showed a binding mode similar to donepezil and interact with the same residues. © 2018 Deutsche Pharmazeutische Gesellschaft.

ACER Mathematics Profile Series: Number Test. (Test Booklet, Answer and Record Sheet, Score Key, and Teachers Handbook).

ERIC Educational Resources Information Center

Cornish, Greg; Wines, Robin

The Number Test of the ACER Mathematics Profile Series, contains 30 items, for each of three suggested grade levels: 7-8, 8-9, and 9-10. Raw scores on all tests in the ACER Mathematics Profile Series (Number, Operations, Space and Measurement) are converted to a common scale called MAPS, a major feature of the Series. Based on the Rasch Model,…

Cross-protection elicited by primary and booster vaccinations against Japanese encephalitis: a two-year follow-up study.

PubMed

Erra, Elina O; Askling, Helena Hervius; Yoksan, Sutee; Rombo, Lars; Riutta, Jukka; Vene, Sirkka; Lindquist, Lars; Vapalahti, Olli; Kantele, Anu

2013-12-17

The inactivated Vero cell-derived vaccine (JE-VC, IXIARO) has replaced the traditional mouse brain-derived preparations (JE-MB) in travelers' vaccinations against Japanese encephalitis. We showed recently that a single JE-VC dose efficiently boosts immunity in JE-MB-primed vaccinees, and that JE-VC elicits cross-protective immunity against non-vaccine genotypes, including the emerging genotype I. While these studies only provided short-term data, the present investigation evaluates the longevity of seroprotection in the same volunteers. The study comprised 48 travelers who had received (1) JE-VC primary series, (2) JE-MB primary series followed by a single JE-VC booster dose, or (3) JE-MB primary series and a single JE-MB booster dose. Serum samples were collected two years after the last vaccine dose, and evaluated with the plaque-reduction neutralization test against seven Japanese encephalitis virus strains representing genotypes I-IV. PRNT50 titers ≥ 10 were considered protective. Two years after the primary series with JE-VC, 87-93% of the vaccinees proved to be cross-protected against test strains representing genotypes II-IV and 73% against those of genotype I. After a single homologous or heterologous booster dose to JE-MB-primed subjects, the two-year seroprotection rates against genotype I-IV strains were 89-100%. After JE-VC primary series, seroprotection appeared to wane first against genotype I. The first booster should not be delayed beyond two years. In JE-MB-primed subjects, a single JE-VC booster provided cross-protective immunity against genotype I-IV strains in almost all vaccinees, suggesting an interval of two years or even longer for the second booster. These data further support the use of a single JE-VC dose for boosting JE-MB immunity. Copyright © 2013 The Authors. Published by Elsevier Ltd.. All rights reserved.

Combined Vocal Exercises for Rehabilitation After Supracricoid Laryngectomy: Evaluation of Different Execution Times.

PubMed

Silveira, Hevely Saray Lima; Simões-Zenari, Marcia; Kulcsar, Marco Aurélio; Cernea, Claudio Roberto; Nemr, Kátia

2017-10-27

The supracricoid partial laryngectomy allows the preservation of laryngeal functions with good local cancer control. To assess laryngeal configuration and voice analysis data following the performance of a combination of two vocal exercises: the prolonged /b/vocal exercise combined with the vowel /e/ using chest and arm pushing with different durations among individuals who have undergone supracricoid laryngectomy. Eleven patients undergoing partial laryngectomy supracricoid with cricohyoidoepiglottopexy (CHEP) were evaluated using voice recording. Four judges performed separately a perceptive-vocal analysis of hearing voices, with random samples. For the analysis of intrajudge reliability, repetitions of 70% of the voices were done. Intraclass correlation coefficient was used to analyze the reliability of the judges. For an analysis of each judge to the comparison between zero time (time point 0), after the first series of exercises (time point 1), after the second series (time point 2), after the third series (time point 3), after the fourth series (time point 4), and after the fifth and final series (time point 5), the Friedman test was used with a significance level of 5%. The data relative to the configuration of the larynx were subjected to a descriptive analysis. In the evaluation, were considered the judge results 1 which have greater reliability. There was an improvement in the general level of vocal, roughness, and breathiness deviations from time point 4 [T4]. The prolonged /b/vocal exercise, combined with the vowel /e/ using chest- and arm-pushing exercises, was associated with an improvement in the overall grade of vocal deviation, roughness, and breathiness starting at minute 4 among patients who had undergone supracricoid laryngectomy with CHEP reconstruction. Copyright © 2017 The Voice Foundation. Published by Elsevier Inc. All rights reserved.

Testing and Analytical Modeling for Purging Process of a Cryogenic Line

NASA Technical Reports Server (NTRS)

Hedayat, A.; Mazurkivich, P. V.; Nelson, M. A.; Majumdar, A. K.

2015-01-01

To gain confidence in developing analytical models of the purging process for the cryogenic main propulsion systems of upper stage, two test series were conducted. The test article, a 3.35 m long with the diameter of 20 cm incline line, was filled with liquid or gaseous hydrogen and then purged with gaseous helium (GHe). Total of 10 tests were conducted. The influences of GHe flow rates and initial temperatures were evaluated. The Generalized Fluid System Simulation Program (GFSSP), an in-house general-purpose fluid system analyzer computer program, was utilized to model and simulate selective tests. The test procedures, modeling descriptions, and the results are presented in the following sections.

Testing and Analytical Modeling for Purging Process of a Cryogenic Line

NASA Technical Reports Server (NTRS)

Hedayat, A.; Mazurkivich, P. V.; Nelson, M. A.; Majumdar, A. K.

2013-01-01

To gain confidence in developing analytical models of the purging process for the cryogenic main propulsion systems of upper stage, two test series were conducted. The test article, a 3.35 m long with the diameter of 20 cm incline line, was filled with liquid or gaseous hydrogen and then purged with gaseous helium (GHe). Total of 10 tests were conducted. The influences of GHe flow rates and initial temperatures were evaluated. The Generalized Fluid System Simulation Program (GFSSP), an in-house general-purpose fluid system analyzer computer program, was utilized to model and simulate selective tests. The test procedures, modeling descriptions, and the results are presented in the following sections.

A Comparison of Methods for Assessing Space Suit Joint Ranges of Motion

NASA Technical Reports Server (NTRS)

Aitchison, Lindsay T.

2012-01-01

Through the Advanced Exploration Systems (AES) Program, NASA is attempting to use the vast collection of space suit mobility data from 50 years worth of space suit testing to build predictive analysis tools to aid in early architecture decisions for future missions and exploration programs. However, the design engineers must first understand if and how data generated by different methodologies can be compared directly and used in an essentially interchangeable manner. To address this question, the isolated joint range of motion data from two different test series were compared. Both data sets were generated from participants wearing the Mark III Space Suit Technology Demonstrator (MK-III), Waist Entry I-suit (WEI), and minimal clothing. Additionally the two tests shared a common test subject that allowed for within subject comparisons of the methods that greatly reduced the number of variables in play. The tests varied in their methodologies: the Space Suit Comparative Technologies Evaluation used 2-D photogrammetry to analyze isolated ranges of motion while the Constellation space suit benchmarking and requirements development used 3-D motion capture to evaluate both isolated and functional joint ranges of motion. The isolated data from both test series were compared graphically, as percent differences, and by simple statistical analysis. The results indicated that while the methods generate results that are statistically the same (significance level p= 0.01), the differences are significant enough in the practical sense to make direct comparisons ill advised. The concluding recommendations propose direction for how to bridge the data gaps and address future mobility data collection to allow for backward compatibility.

Beyond Correlation in the Detection of Climate Change Impacts: Testing a Mechanistic Hypothesis for Climatic Influence on Sockeye Salmon (Oncorhynchus nerka) Productivity.

PubMed

Tillotson, Michael D; Quinn, Thomas P

2016-01-01

Detecting the biological impacts of climate change is a current focus of ecological research and has important applications in conservation and resource management. Owing to a lack of suitable control systems, measuring correlations between time series of biological attributes and hypothesized environmental covariates is a common method for detecting such impacts. These correlative approaches are particularly common in studies of exploited fish species because rich biological time-series data are often available. However, the utility of species-environment relationships for identifying or predicting biological responses to climate change has been questioned because strong correlations often deteriorate as new data are collected. Specifically stating and critically evaluating the mechanistic relationship(s) linking an environmental driver to a biological response may help to address this problem. Using nearly 60 years of data on sockeye salmon from the Kvichak River, Alaska we tested a mechanistic hypothesis linking water temperatures experienced during freshwater rearing to population productivity by modeling a series of intermediate, deterministic relationships and evaluating temporal trends in biological and environmental time-series. We found that warming waters during freshwater rearing have profoundly altered patterns of growth and life history in this population complex yet there has been no significant correlation between water temperature and metrics of productivity commonly used in fisheries management. These findings demonstrate that pairing correlative approaches with careful consideration of the mechanistic links between populations and their environments can help to both avoid spurious correlations and identify biologically important, but not statistically significant relationships, and ultimately producing more robust conclusions about the biological impacts of climate change.

Beyond Correlation in the Detection of Climate Change Impacts: Testing a Mechanistic Hypothesis for Climatic Influence on Sockeye Salmon (Oncorhynchus nerka) Productivity

PubMed Central

Tillotson, Michael D.; Quinn, Thomas P.

2016-01-01

Detecting the biological impacts of climate change is a current focus of ecological research and has important applications in conservation and resource management. Owing to a lack of suitable control systems, measuring correlations between time series of biological attributes and hypothesized environmental covariates is a common method for detecting such impacts. These correlative approaches are particularly common in studies of exploited fish species because rich biological time-series data are often available. However, the utility of species-environment relationships for identifying or predicting biological responses to climate change has been questioned because strong correlations often deteriorate as new data are collected. Specifically stating and critically evaluating the mechanistic relationship(s) linking an environmental driver to a biological response may help to address this problem. Using nearly 60 years of data on sockeye salmon from the Kvichak River, Alaska we tested a mechanistic hypothesis linking water temperatures experienced during freshwater rearing to population productivity by modeling a series of intermediate, deterministic relationships and evaluating temporal trends in biological and environmental time-series. We found that warming waters during freshwater rearing have profoundly altered patterns of growth and life history in this population complex yet there has been no significant correlation between water temperature and metrics of productivity commonly used in fisheries management. These findings demonstrate that pairing correlative approaches with careful consideration of the mechanistic links between populations and their environments can help to both avoid spurious correlations and identify biologically important, but not statistically significant relationships, and ultimately producing more robust conclusions about the biological impacts of climate change. PMID:27123845

Design of Refractory Metal Life Test Heat Pipe and Calorimeter

NASA Technical Reports Server (NTRS)

Martin, J. J.; Reid, R. S.; Bragg-Sitton, S. M.

2010-01-01

Heat pipe life tests have seldom been conducted on a systematic basis. Typically, one or more heat pipes are built and tested for an extended period at a single temperature with simple condenser loading. Results are often reported describing the wall material, working fluid, test temperature, test duration, and occasionally the nature of any failure. Important information such as design details, processing procedures, material assay, power throughput, and radial power density are usually not mentioned. We propose to develop methods to generate carefully controlled data that conclusively establish heat pipe operating life with material-fluid combinations capable of extended operation. The test approach detailed in this Technical Publication will use 16 Mo-44.5%Re alloy/sodium heat pipe units that have an approximate12-in length and 5/8-in diameter. Two specific test series have been identified: (1) Long-term corrosion rates based on ASTM-G-68-80 (G-series) and (2) corrosion trends in a cross-correlation sequence at various temperatures and mass fluences based on a Fisher multifactor design (F-series). Evaluation of the heat pipe hardware will be performed in test chambers purged with an inert purified gas (helium or helium/argon mixture) at low pressure (10-100 torr) to provide thermal coupling between the heat pipe condenser and calorimeter. The final pressure will be selected to minimize the potential for voltage breakdown between the heat pipe and radio frequency (RF) induction coil (RF heating is currently the planned method of powering the heat pipes). The proposed calorimeter is constructed from a copper alloy and relies on a laminar flow water-coolant channel design to absorb and transport energy

Product assurance technology for procuring reliable, radiation-hard, custom LSI/VLSI electronics

NASA Technical Reports Server (NTRS)

Buehler, M. G.; Allen, R. A.; Blaes, B. R.; Hicks, K. A.; Jennings, G. A.; Lin, Y.-S.; Pina, C. A.; Sayah, H. R.; Zamani, N.

1989-01-01

Advanced measurement methods using microelectronic test chips are described. These chips are intended to be used in acquiring the data needed to qualify Application Specific Integrated Circuits (ASIC's) for space use. Efforts were focused on developing the technology for obtaining custom IC's from CMOS/bulk silicon foundries. A series of test chips were developed: a parametric test strip, a fault chip, a set of reliability chips, and the CRRES (Combined Release and Radiation Effects Satellite) chip, a test circuit for monitoring space radiation effects. The technical accomplishments of the effort include: (1) development of a fault chip that contains a set of test structures used to evaluate the density of various process-induced defects; (2) development of new test structures and testing techniques for measuring gate-oxide capacitance, gate-overlap capacitance, and propagation delay; (3) development of a set of reliability chips that are used to evaluate failure mechanisms in CMOS/bulk: interconnect and contact electromigration and time-dependent dielectric breakdown; (4) development of MOSFET parameter extraction procedures for evaluating subthreshold characteristics; (5) evaluation of test chips and test strips on the second CRRES wafer run; (6) two dedicated fabrication runs for the CRRES chip flight parts; and (7) publication of two papers: one on the split-cross bridge resistor and another on asymmetrical SRAM (static random access memory) cells for single-event upset analysis.

Nonlinear dynamic analysis of D α signals for type I edge localized modes characterization on JET with a carbon wall

NASA Astrophysics Data System (ADS)

Cannas, Barbara; Fanni, Alessandra; Murari, Andrea; Pisano, Fabio; Contributors, JET

2018-02-01

In this paper, the dynamic characteristics of type-I ELM time-series from the JET tokamak, the world’s largest magnetic confinement plasma physics experiment, have been investigated. The dynamic analysis has been focused on the detection of nonlinear structure in D α radiation time series. Firstly, the method of surrogate data has been applied to evaluate the statistical significance of the null hypothesis of static nonlinear distortion of an underlying Gaussian linear process. Several nonlinear statistics have been evaluated, such us the time delayed mutual information, the correlation dimension and the maximal Lyapunov exponent. The obtained results allow us to reject the null hypothesis, giving evidence of underlying nonlinear dynamics. Moreover, no evidence of low-dimensional chaos has been found; indeed, the analysed time series are better characterized by the power law sensitivity to initial conditions which can suggest a motion at the ‘edge of chaos’, at the border between chaotic and regular non-chaotic dynamics. This uncertainty makes it necessary to further investigate about the nature of the nonlinear dynamics. For this purpose, a second surrogate test to distinguish chaotic orbits from pseudo-periodic orbits has been applied. In this case, we cannot reject the null hypothesis which means that the ELM time series is possibly pseudo-periodic. In order to reproduce pseudo-periodic dynamical properties, a periodic state-of-the-art model, proposed to reproduce the ELM cycle, has been corrupted by a dynamical noise, obtaining time series qualitatively in agreement with experimental time series.

Risk evaluation on leading companies in property and real estate subsector at IDX: A Value-at-Risk with ARMAX-GARCHX approach and duration test

NASA Astrophysics Data System (ADS)

Dwi Prastyo, Dedy; Handayani, Dwi; Fam, Soo-Fen; Puteri Rahayu, Santi; Suhartono; Luh Putu Satyaning Pradnya Paramita, Ni

2018-03-01

Risk assessment and evaluation becomes essential for financial institution to measure the potential risk of their counterparties. In middle of 2016 until first quarter of 2017, there is national program from Indonesian government so-called Tax Amnesty. One subsector that has potential to receive positive impact from the Tax Amnesty program is property and real estate. This work evaluates the risk of top five companies in term of capital share listed in Indonesia stock exchange (IDX). To do this, the Value-at-Risk (VaR) with ARMAX-GARCHX approach is employed. The ARMAX-GARCHX simultaneously models the adaptive mean and variance of stock return of each company considering exogenous variables, i.e. IDR/USD exchange rate and Jakarta Composite Index (JCI). The risk is evaluated in scheme of time moving window. The risk evaluation using 5% quantile with window size 500 transaction days perform better result compare to other scenarios. In addition, duration test is used to test the dependency between shortfalls. It informs that series of shortfall are independent.

Evaluating the time and temperature dependent biaxial strength of Gore-Select ® series 57 proton exchange membrane using a pressure loaded blister test

NASA Astrophysics Data System (ADS)

Grohs, Jacob R.; Li, Yongqiang; Dillard, David A.; Case, Scott W.; Ellis, Michael W.; Lai, Yeh-Hung; Gittleman, Craig S.

Temperature and humidity fluctuations in operating fuel cells impose significant biaxial stresses in the constrained proton exchange membranes (PEMs) of a fuel cell stack. The strength of the PEM, and its ability to withstand cyclic environment-induced stresses, plays an important role in membrane integrity and consequently, fuel cell durability. In this study, a pressure loaded blister test is used to characterize the biaxial strength of Gore-Select ® series 57 over a range of times and temperatures. Hencky's classical solution for a pressurized circular membrane is used to estimate biaxial strength values from burst pressure measurements. A hereditary integral is employed to construct the linear viscoelastic analog to Hencky's linear elastic exact solution. Biaxial strength master curves are constructed using traditional time-temperature superposition principle techniques and the associated temperature shift factors show good agreement with shift factors obtained from constitutive (stress relaxation) and fracture (knife slit) tests of the material.

Biological treatment of hazardous aqueous wastes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Opatken, E.J.; Howard, H.K.; Bond, J.J.

1987-06-01

Studies were conducted with a rotating biological conractor (RBC) to evaluate the treatability of leachates from the Stringfellow and New Lyme hazardous-waste sites. The leachates were transported from the waste sites to Cincinnati at the United States Environmental Protection Agency's Testing and Evaluation Facility. A series of batches were run with primary effluent from Cincinnati's Mill Creek Sewage Treatment Facility. The paper reports on the results from these experiments and the effectiveness of an RBC to adequately treat leachates from Superfund sites.

Space Suit Portable Life Support System (PLSS) 2.0 Unmanned Vacuum Environment Testing

NASA Technical Reports Server (NTRS)

Watts, Carly; Vogel, Matthew

2016-01-01

For the first time in more than 30 years, an advanced space suit Portable Life Support System (PLSS) design was operated inside a vacuum chamber representative of the flight operating environment. The test article, PLSS 2.0, was the second system-level integrated prototype of the advanced PLSS design, following the PLSS 1.0 Breadboard that was developed and tested throughout 2011. Whereas PLSS 1.0 included five technology development components with the balance the system simulated using commercial-off-the-shelf items, PLSS 2.0 featured first generation or later prototypes for all components less instrumentation, tubing and fittings. Developed throughout 2012, PLSS 2.0 was the first attempt to package the system into a flight-like representative volume. PLSS 2.0 testing included an extensive functional evaluation known as Pre-Installation Acceptance (PIA) testing, Human-in-the-Loop testing in which the PLSS 2.0 prototype was integrated via umbilicals to a manned prototype space suit for 19 two-hour simulated EVAs, and unmanned vacuum environment testing. Unmanned vacuum environment testing took place from 1/9/15-7/9/15 with PLSS 2.0 located inside a vacuum chamber. Test sequences included performance mapping of several components, carbon dioxide removal evaluations at simulated intravehicular activity (IVA) conditions, a regulator pressure schedule assessment, and culminated with 25 simulated extravehicular activities (EVAs). During the unmanned vacuum environment test series, PLSS 2.0 accumulated 378 hours of integrated testing including 291 hours of operation in a vacuum environment and 199 hours of simulated EVA time. The PLSS prototype performed nominally throughout the test series, with two notable exceptions including a pump failure and a Spacesuit Water Membrane Evaporator (SWME) leak, for which post-test failure investigations were performed. In addition to generating an extensive database of PLSS 2.0 performance data, achievements included requirements and operational concepts verification, as well as demonstration of vehicular interfaces, consumables sizing and recharge, and water quality control.

Arc Jet Testing of the TIRS Cover Thermal Protection System for Mars Exploration Rover

NASA Technical Reports Server (NTRS)

Szalai, Christine E.; Chen, Y.-K.; Loomis, Mark; Hui, Frank; Scrivens, Larry

2002-01-01

This paper summarizes the arc jet test results of the Mars Exploration Rover (MER) Silicone Impregnated Reusable Ceramic Ablator (SIRCA) Transverse Impulse Rocket System (TIRS) Cover test series in the Panel Test Facility (PTF) at NASA Ames Research Center (ARC). NASA ARC performed aerothermal environment analyses, TPS sizing and thermal response analyses, and arc jet testing to evaluate the MER SIRCA TIRS Cover design and interface to the aeroshell structure. The primary objective of this arc jet test series was to evaluate specific design details of the SIRCA TIRS Cover interface to the MER aeroshell under simulated atmospheric entry heating conditions. Four test articles were tested in an arc jet environment with various sea] configurations. The test condition was designed to match the predicted peak flight heat load at the gap region between the SIRCA and the backshell TPS material, SLA-561S, and resulted in an over-test (with respect to heat flux and heat load) for the apex region of the SIRCA TIRS Cover. The resulting pressure differential was as much as twenty times that predicted for the flight case, depending on the location, and there was no post-test visual evidence of over-heating or damage to the seal, bracket, or backshell structure. The exposed titanium bolts were in good condition at post-test and showed only a small amount of oxidation at the leading edge locations. Repeatable thermocouple data were obtained and SIRCA thermal response analyses were compared to applicable thermocouple data. For the apex region of the SIRCA TIRS Cover, a one-dimensional thermal response prediction proved overly conservative, as there were strong multi-dimensional conduction effects evident from the thermocouple data. The one-dimensional thermal response prediction compared well with the thermocouple data for the leading edge "lip" region at the bolt location. In general, the test results yield confidence in the baseline seal design to prevent hot gas ingestion at the bracket and composite aeroshell structure interface.

Planetary Geomorphology

NASA Technical Reports Server (NTRS)

Malin, Michael C.

1990-01-01

One of the major problems in the series of ice runs was that the subsurface temperature probes did not function. AIC re-evaluated the design and, after testing several suitable sensors, installed 50 type T thermocouples, each 2 m long. In this design, each thermocouple was soldered to a rectangular copper foil spreader 0.3 com wide by 2.8 cm long to ensure an acute reading. The long rectangular shape was used because it had a large area for good thermal connection to the test material.

Test Evaluation and Modification of Prototype Rotating Gravity Gradiometer

DTIC Science & Technology

1975-07-01

RECOMMENEATIONS 3 4.0 BEARINGS 6 4.1 Design 6 4.2 Metrology 6 4.3 Preassembly 14 5.0 TEST RIG 17 5.1 Design 17 5.2 Metrology 21 5.3 Assembly and...print requirements of 5 \\i inches TIR max. However, because of available (stare-of-the-art) metrology equipment limitations, no conclusion as to...gravity gradiometer are contained in Shaker Research Corporation drawing series 101 (see Appendix I), 4.2 Metrology The production of the

The effects of 1 kW class arcjet thruster plumes on spacecraft charging and spacecraft thermal control materials

NASA Technical Reports Server (NTRS)

Bogorad, A.; Lichtin, D. A.; Bowman, C.; Armenti, J.; Pencil, E.; Sarmiento, C.

1992-01-01

Arcjet thrusters are soon to be used for north/south stationkeeping on commercial communications satellites. A series of tests was performed to evaluate the possible effects of these thrusters on spacecraft charging and the degradation of thermal control material. During the tests the interaction between arcjet plumes and both charged and uncharged surfaces did not cause any significant material degradation. In addition, firing an arcjet thruster benignly reduced the potential of charged surfaces to near zero.

Heat storage capability of a rolling cylinder using Glauber's salt

NASA Technical Reports Server (NTRS)

Herrick, C. S.; Zarnoch, K. P.

1980-01-01

The rolling cylinder phase change heat storage concept was developed to the point where a prototype design is completed and a cost analysis is prepared. A series of experimental and analytical tasks are defined to establish the thermal, mechanical, and materials behavior of rolling cylinder devices. These tasks include: analyses of internal and external heat transfer; performance and lifetime testing of the phase change materials; corrosion evaluation; development of a mathematical model; and design of a prototype and associated test equipment.

Assessment of a Point-of-Use Ultrafiltration System for Turbidity and Microbial Pathogen Removal - Paper

EPA Science Inventory

U.S. EPA’s Office of Research and Development has been evaluating the performance of point-of-use (POU) devices designed for use in homes and small businesses for many years. In collaboration with the University of Cincinnati, a series of pilot-scale tests were conducted on a Ma...

Improving Longleaf Pine Seedling Establishment in the Nursery by Reducing Seedcoat Microorganisms

Treesearch

James Barnett; Bill Pickens; Robert Karrfalt

1999-01-01

Longleaf pine (Pinus palustris Mill.) seeds are sensitive to damage during collection, processing, and storage. Highquality seeds are essential for successful production of nursery crops that meet management goals and perform well in the field. We conducted a series of tests under laboratory and nursery conditions to evaluate what effect a number of...

THE FATE OF TRACE METALS IN A ROTARY KILN INCINERATOR WITH A VENTURI/PACKED COLUMN SCRUBBER - VOLUME II: APPENDICES

EPA Science Inventory

A 5-week series of pilot-scale incineration tests, employing a synthetic waste feed, was performed at the U.S. Environmental Protection Agency's Incineration Research Facility to evaluate the fate of trace metals fed to a rotary kiln incinerator equipped with a venturi scrubber/p...

Carnegie Knowledge Network Concluding Recommendations. What We Know Series

ERIC Educational Resources Information Center

Goldhaber, Dan; Harris Douglas N.; Loeb, Susanna; McCaffrey, Daniel F.; Raudenbush, Stephen W.

2015-01-01

It is common knowledge that teacher quality is a key in-school factor affecting student achievement. While the quality of teaching clearly matters for how much students learn, this quality is challenging to measure. Evaluating teacher quality based on the level of their students' end-of-year test scores has been one method of assessing…

Informing Lake Erie agriculture nutrient management via scenario evaluation

USGS Publications Warehouse

Scavia, Donald; Kalcic, Margaret; Muenich, Rebecca Logsdon; Aloysius, Noel; Arnold, Jeffrey; Boles, Chelsie; Confesor, Remegio; DePinto, Joseph; Gildow, Marie; Martin, Jay; Read, Jennifer; Redder, Todd; Robertson, Dale M.; Sowa, Scott P.; Wang, Yu-Chen; White, Michael; Yen, Haw

2016-01-01

Therefore, the overall goal of this study was to identify potential options for agricultural management to reduce phosphorus loads and lessen future HABs in Lake Erie. We applied multiple watershed models to test the ability of a series of land management scenarios, developed in consultation with agricultural and environmental stakeholders, to reach the proposed targets. 

FATE OF TRACE METALS IN A ROTARY KILN INCINERATOR WITH A SINGLE-STAGE IONIZING WET SCRUBBER. VOLUME 1. TECHNICAL RESULTS.

EPA Science Inventory

A series of pilot-scale incineration tests was performed at EPA's Incineration Research Facility (IRF) in Jefferson, Arkansas, to evaluate the fate of trace metals fed to a rotary kiln incinerator equipped with an ionizing wet scrubber (IWS) for particulate and acid gas control. ...

Longleaf Pine Seed Presowing Treatements: Effects on Germination and Nursery Establishment

Treesearch

James P. Barnett; Bill Pickens; Robert Karrfalt

1999-01-01

Longleaf pine (Pinus patustris Mill.) seeds are sensitive to damage during collection, processing, and storage. High-quality seeds are essential for successful production of nursery crops that meet management goals and perform well in the field. A series of tests was conducted to evaluate the effect of a number of presowing treatments, e.g.,...

Curriculum Reform: Assessment in Question (La Reforme des Programmes Scolaires: L'Evaluation en Question).

ERIC Educational Resources Information Center

Organisation for Economic Cooperation and Development, Paris (France). Centre for Educational Research and Innovation.

In today's schools, the pervasiveness of assessment has often distorted teaching and learning through testing, examining, and short-term memorizing. Learning to cope with examinations has become almost as important as the learning itself. This report is the third in a series of publications derived from the Centre for Educational Research and…

Experimental Evidence on the Effectiveness of Automated Essay Scoring in Teacher Education Cases

ERIC Educational Resources Information Center

Riedel, Eric; Dexter, Sara L.; Scharber, Cassandra; Doering, Aaron

2006-01-01

Research on computer-based writing evaluation has only recently focused on the potential for providing formative feedback rather than summative assessment. This study tests the impact of an automated essay scorer (AES) that provides formative feedback on essay drafts written as part of a series of online teacher education case studies. Seventy…

Innovations: The Social Consequences of Science and Technology. Final Evaluation Report.

ERIC Educational Resources Information Center

Tolman, Richard R.

The Biological Sciences Curriculum Study designed, developed, and field-tested a series of nine curriculum resource units for a semester program called "Innovations: The Social Consequences of Science and Technology (IST)." The units were designed for use by students and teachers in the 11th and 12th grades and at the junior college…

ENVIRONMENTAL IMPACTS OF THE USE OF ORIMULSION.: REPORT TO CONGRESS ON PHASE 1 OF THE ORIMULSION TECHNOLOGY ASSESSMENT PROGRAM

EPA Science Inventory

Orimulsion, a bitumen-in-water emulsion produced in Venezuela, was
evaluated to provide a better understanding of the potential environmental
impacts associated with its use as a fuel. A series of pilot-scale tests were
conducted at the U.S. Environmental Protection Agen...

Individualized Instruction for Data Access (IIDA). Quarterly Reports No. 5-6.

ERIC Educational Resources Information Center

Drexel Univ., Philadelphia, PA. Graduate School of Library Science.

These quarterly reports for June and September 1979 are two in a series concerned with describing a research project to design, test, and evaluate a machine intermediary which teaches and assists users of the DIALOG system. Report No. 5 explains in detail the instructional aspect of the Individualized Instruction for Data Access (IIDA) project and…

Law enforcement officers in the USDA forest service

Treesearch

Deborah J. Chavez; Joanne F. Tynon

2006-01-01

This paper reports results fiom the first in a series of studies evaluating perceptions of law enforcement officers (LEOs) in the US Forest Service (USFS). It is a follow-up to previous qualitative studies conducted to learn more about crime and violence in national forests and the impacts on recreation visitation and management, and test key characteristics of success...

THE FATE OF TRACE METALS IN A ROTARY KILN INCINERATOR WITH A SINGLE-STAGE IONIZING WET SCRUBBER - VOLUME II: APPENDICES

EPA Science Inventory

A series of pilot-scale incineration tests was performed at EPA's Incineration Research Facility (IRF) in Jefferson, Arkansas, to evaluate the fate of trace metals fed to a rotary kiln incinerator equipped with an ionizing wet scrubber (IWS) for particulate and acid gas control. ...

The U.S. Constitution: An Evaluation of the 'Federalism' Program. Research Report Number 99.

ERIC Educational Resources Information Center

Agency for Instructional Technology, Bloomington, IN.

This report describes the results of a field test of "Federalism", a program from "The U.S. Constitution", an instructional video program series for secondary school students developed by the Agency for Instructional Technology (AIT) in association with Project '87. The participants of the preview are teachers and students in…

On-orbit evaluation of the control system/structural mode interactions on OSO-8

NASA Technical Reports Server (NTRS)

Slafer, L. I.

1980-01-01

The Orbiting Solar Observatory-8 experienced severe structural mode/control loop interaction problems during the spacecraft development. Extensive analytical studies, using the hybrid coordinate modeling approach, and comprehensive ground testing were carried out in order to achieve the system's precision pointing performance requirements. A recent series of flight tests were conducted with the spacecraft in which a wide bandwidth, high resolution telemetry system was utilized to evaluate the on-orbit flexible dynamics characteristics of the vehicle along with the control system performance. This paper describes the results of these tests, reviewing the basic design problem, analytical approach taken, ground test philosophy, and on-orbit testing. Data from the tests was used to determine the primary mode frequency, damping, and servo coupling dynamics for the on-orbit condition. Additionally, the test results have verified analytically predicted differences between the on-orbit and ground test environments. The test results have led to a validation of both the analytical modeling and servo design techniques used during the development of the control system, and also verified the approach taken to vehicle and servo ground testing.

Demonstration of Robustness and Integrated Operation of a Series-Bosch System

NASA Technical Reports Server (NTRS)

Abney, Morgan B.; Mansell, J. Matthew; Barnett, Bill; Stanley, Christine M.; Junaedi, Christian; Vilekar, Saurabh A.; Kent, Ryan

2016-01-01

Manned missions beyond low Earth orbit will require highly robust, reliable, and maintainable life support systems that maximize recycling of water and oxygen. Bosch technology is one option to maximize oxygen recovery, in the form of water, from metabolically-produced carbon dioxide (CO2). A two stage approach to Bosch, called Series-Bosch, reduces metabolic CO2 with hydrogen (H2) to produce water and solid carbon using two reactors: a Reverse Water-Gas Shift (RWGS) reactor and a carbon formation (CF) reactor. Previous development efforts demonstrated the stand-alone performance of a RWGS reactor containing Incofoam(TradeMark) catalyst and designed for robustness against carbon formation, two membrane separators intended to maximize single pass conversion of reactants, and a batch CF reactor with both transit and surface catalysts. In the past year, Precision Combustion, Inc. (PCI) developed and delivered a RWGS reactor for testing at NASA. The reactor design was based on their patented Microlith(TradeMark) technology and was first evaluated under a Phase I Small Business Innovative Research (SBIR) effort in 2010. The Microlith(TradeMark) RWGS reactor was recently evaluated at NASA to compare its performance and operating conditions with the Incofoam(TradeMark) RWGS reactor. Separately, in 2015, a fully integrated demonstration of an S-Bosch system was conducted. In an effort to mitigate risk, a second integrated test was conducted to evaluate the effect of membrane failure on a closed-loop Bosch system. Here, we report and discuss the performance and robustness to carbon formation of both RWGS reactors. We report the results of the integrated operation of a Series-Bosch system and we discuss the technology readiness level. 1

Use of Traditional and Novel Methods to Evaluate the Influence of an EVA Glove on Hand Performance

NASA Technical Reports Server (NTRS)

Benson, Elizabeth A.; England, Scott A.; Mesloh, Miranda; Thompson, Shelby; ajulu, Sudhakar

2010-01-01

The gloved hand is one of an astronaut s primary means of interacting with the environment, and any restrictions imposed by the glove can strongly affect performance during extravehicular activity (EVA). Glove restrictions have been the subject of study for decades, yet previous studies have generally been unsuccessful in quantifying glove mobility and tactility. Past studies have tended to focus on the dexterity, strength, and functional performance of the gloved hand; this provides only a circumspect analysis of the impact of each type of restriction on the glove s overall capability. The aim of this study was to develop novel capabilities to provide metrics for mobility and tactility that can be used to assess the performance of a glove in a way that could enable designers and engineers to improve their current designs. A series of evaluations were performed to compare unpressurized and pressurized (4.3 psi) gloved conditions with the ungloved condition. A second series of evaluations were performed with the Thermal Micrometeoroid Garment (TMG) removed. This series of tests provided interesting insight into how much of an effect the TMG has on gloved mobility - in some cases, the presence of the TMG restricted glove mobility as much as pressurization did. Previous hypotheses had assumed that the TMG would have a much lower impact on mobility, but these results suggest that an improvement in the design of the TMG could have a significant impact on glove performance. Tactility testing illustrated the effect of glove pressurization, provided insight into the design of hardware that interfaces with the glove, and highlighted areas of concern. The metrics developed in this study served to benchmark the Phase VI EVA glove and to develop requirements for the next-generation glove for the Constellation program.

Adjunctive effect of chlorhexidine antiseptics in mechanical periodontal treatment: first results of a preliminary case series.

PubMed

Calderini, A; Pantaleo, G; Rossi, A; Gazzolo, D; Polizzi, E

2013-08-01

The aim of the present case series was to evaluate the clinical and microbiological effects of a single session of mechanical and manual scaling and root planing (SRP) combined with the use of two different chlorhexidine formulations in the treatment for generalized chronic periodontitis. Ten patients affected by chronic periodontal disease with periodontal probing depth (PPD) ≥ 5 mm were treated with SRP plus local chlorhexidine. In each patient, similar teeth, treated with SRP with the adjunctive use of chlorhexidine digluconate and dihydrochloride or chlorhexidine gluconate, respectively, were selected and assigned to a test and a control group. In both groups, PPD, bleeding on probing (BOP) parameters, total bacterial counts (TBC) and quality of periodontal bacteria at time 0 and 6 weeks after treatment were measured. PPD significantly decreased over time both in the test and in the control group; however, no significant differences between the two groups were observed. BOP and TBC were significantly lower in the test than in the control group 6 weeks after treatment. In the post-treatment revaluation, a significant decrease both in the treatment and in the control group, for each of the single periodontal pathogens, was observed. In this study--a preliminary case series with small sample size and short follow-up--the adjunctive use of chlorhexidine (CHX) to SRP resulted in clinical and microbiological benefits in the treatment for generalized chronic periodontitis. A CHX gel formulation consisting of CHX digluconate and CHX dihydrochloride seems to lead some additional benefits over SRP plus CHX gluconate in the short term. Additional investigations are needed to evaluate the effectiveness of this antiseptic therapy. © 2012 John Wiley & Sons A/S.