Science.gov

Sample records for exhaust emissions evaluation

  1. Evaluating tractor performance and exhaust gas emissions using biodiesel from cotton seed oil

    NASA Astrophysics Data System (ADS)

    Al-lwayzy, Saddam H.; Yusaf, Talal; Jensen, Troy

    2012-09-01

    Alternative fuels for diesel engines, such as biodiesel, have attracted much attention recently due to increasing fuel prices and the imperative to reduce emissions. The exhaust gas emissions from tractors and other agricultural machinery make a significant contribution to these emissions. The use of biodiesel in internal combustion engines (ICE) has been reported to give comparable performance to conventional diesel (CD), but with generally lower emissions. There is however, contradictory evidence of NO emissions being both higher and lower from the use of biodiesel. In this work, agriculture tractor engine performance and its emission using both CD and biodiesel from cotton seed oil (CSO-B20) mixed at a 20% blend ration has been evaluated and compared. The PTO test results showed comparable exhaust emissions between CD and CSO-B20. However, the use of CSO-B20 led to reductions in the thermal efficiency and exhaust temperature and an increase in the brake specific fuel consumption (BSFC), when compared to CD.

  2. New exposure system to evaluate the toxicity of (scooter) exhaust emissions in lung cells in vitro.

    PubMed

    Müller, Loretta; Comte, Pierre; Czerwinski, Jan; Kasper, Markus; Mayer, Andreas C R; Gehr, Peter; Burtscher, Heinz; Morin, Jean-Paul; Konstandopoulos, Athanasios; Rothen-Rutishauser, Barbara

    2010-04-01

    A constantly growing number of scooters produce an increasing amount of potentially harmful emissions. Due to their engine technology, two-stroke scooters emit huge amounts of adverse substances, which can induce adverse pulmonary and cardiovascular health effects. The aim of this study was to develop a system to expose a characterized triple cell coculture model of the human epithelial airway barrier, to freshly produced and characterized total scooter exhaust emissions. In exposure chambers, cell cultures were exposed for 1 and 2 h to 1:100 diluted exhaust emissions and in the reference chamber to filtered ambient air, both controlled at 5% CO(2), 85% relative humidity, and 37 degrees C. The postexposure time was 0-24 h. Cytotoxicity, used to validate the exposure system, was significantly increased in exposed cell cultures after 8 h postexposure time. (Pro-) inflammatory chemo- and cytokine concentrations in the medium of exposed cells were significantly higher at the 12 h postexposure time point. It was shown that the described exposure system (with 2 h exposure duration, 8 and 24 h postexposure time, dilution of 1:100, flow of 2 L/min as optimal exposure conditions) can be used to evaluate the toxic potential of total exhaust emissions.

  3. Exhaust emission control apparatus

    SciTech Connect

    Eng, J.W.

    1991-09-24

    This patent describes an exhaust control apparatus for muffling noise and treating odors and pollutants, including solid particulate and gases in the exhaust of an internal combustion engine. It comprises an exhaust inlet tube for receiving the exhaust generated by an internal combustion engine; a cyclone barrier concentrically surrounding the exhaust inlet tube, a ring cavity between the cyclone tube and exhaust inlet tube defining a cyclone chamber in which the exhaust is treated; means for directing the exhaust from the exhaust inlet tube into the cyclone chamber; electrode means having small openings through which the exhaust passes to enter the cyclone chamber, the electrode means generating electrostatic forces which charge the solid particulate in the exhaust, ionize air and generate ozone in the cyclone chamber near the electrode; means for injecting air into the cyclone chamber causing centrifugal flow of the air and the exhausted within the cyclone chamber and increasing a dwell time of the exhaust within the cyclone chamber.

  4. [Evaluation on the Effectiveness of Vehicle Exhaust Emission Control Measures During the APEC Conference in Beijing].

    PubMed

    Fan, Shou-bin; Tian, Ling-di; Zhang, Dong-xu; Guo, Jin-jin

    2016-01-15

    Vehicle emission is one of the primary factors affecting the quality of atmospheric environment in Beijing. In order to improve the air quality during APEC conference, strict control measures including vehicle emission control were taken in Beijing during APEC meeting. Based on the activity level data of traffic volume, vehicle speed and vehicle types, the inventory of motor vehicle emissions in Beijing was developed following bottom-up methodology to assess the effectiveness of the control measures. The results showed that the traffic volume of Beijing road network during the APEC meeting decreased significantly, the vehicle speed increased obviously, and the largest decline of traffic volume was car. CO, NOx, HC and PM emissions of vehicle exhaust were reduced by 15.1%, 22.4%, 18.4% and 21.8% for freeways, 29.9%, 36.4%, 32.7% and 35.8% for major arterial, 35.7%, 41.7%, 38.4% and 41.2% for minor arterial, 40.8%, 46.5%, 43.1% and 46.0% for collectors, respectively. The vehicles exhaust emissions inventory before and during APEC conference was developed based on bottom-up emissions inventory method. The results indicated that CO, NOx, HC and PM emissions of vehicle exhaust were reduced by 37.5%, 43.4%, 39.9% and 42.9% in the study area, respectively.

  5. Evaluation of FTIR emission spectrometry for the determination of turbine exhaust composition in test beds

    NASA Astrophysics Data System (ADS)

    Schaefer, Klaus; Heland, Joerg; Lister, Dave H.; Lindermeir, Erwin; Hilton, Moira; Bishop, Gary; Wiesen, Peter; Bernard, Marc

    1999-09-01

    The capability of taking non-intrusive species measurements in a jet plume of a modified mid-size low by-pass aero-engine running on a sea level test bed at several thrust levels was demonstrated. Also conventional intrusive measurements were performed with a spatially resolved method using a traversing single-point sampling probe which fulfills ICAO standards. The FTIR spectrometry measurements included both emission and absorption mode with a multi-path reflection compartment as well as the single emission mode. Due to the lack of a common/unique definition for the exhaust plume diameter it was found that the column density was the best measure to compare the different techniques. The FTIR engine measurement results for CO2, CO, and NO have been proven to be in agreement with the intrusive data within plus or minus 30%. Several error sources during the radiometric radiance calibration were identified which lead to uncertainties in the FTIR retrievals, namely (1) incomplete knowledge of the optical surface emissivities, (2) incomplete knowledge and inhomogeneities of the optical surface temperature, and (3) undefined instrumental drifts and non-linearities during the calibration.

  6. Exhaust emission control and diagnostics

    DOEpatents

    Mazur, Christopher John; Upadhyay, Devesh

    2006-11-14

    A diesel engine emission control system uses an upstream oxidation catalyst and a downstream SCR catalyst to reduce NOx in a lean exhaust gas environment. The engine and upstream oxidation catalyst are configured to provide approximately a 1:1 ratio of NO to NO2 entering the downstream catalyst. In this way, the downstream catalyst is insensitive to sulfur contamination, and also has improved overall catalyst NOx conversion efficiency. Degradation of the system is determined when the ratio provided is no longer near the desired 1:1 ratio. This condition is detected using measurements of engine operating conditions such as from a NOx sensor located downstream of the catalysts. Finally, control action to adjust an injected amount of reductant in the exhaust gas based on the actual NO to NO2 ratio upstream of the SCR catalyst and downstream of the oxidation catalyst.

  7. Evaluation of the Dekati mass monitor for the measurement of exhaust particle mass emissions.

    PubMed

    Mamakos, Athanasios; Ntziachristos, Leonidas; Samaras, Zissis

    2006-08-01

    The Dekati mass monitor (OMM) is an instrument which measures the mass concentration of airborne particles in real time by combining aerodynamic and mobility size particle classification. In this study, we evaluate the performance of the DMM by sampling exhaust from five engines and vehicles of different technologies in both steady-state and transient tests. DMM results are found higher than the filter-based particulate matter (PM) by 39 +/- 24% (range stands for +/- one standard deviation) for 62 diesel tests conducted in total and 3% and 14% higher, respectively, in two gasoline tests. To explore whether the difference occurs because of the different measurement principles of DMM and filter-based PM, the DMM operation is replicated over steady-state tests by combining an electrical low-pressure impactor (ELPI) and a scanning mobility particle sizer (SMPS). The correlation of ELPI and SMPS derived mass and filter-based PM is satisfactory (R2 = 0.95) with a mean deviation of 5 +/- 15%. For the same tests, the correlation of DMM with PM was also high (R2 = 0.95), but DMM exceeded PM by 44 +/- 23% on average. The comparison of ELPI and SMPS and DMM results reveals that the latter overestimates both the geometric mean diameter and especially the width of the particle mass-weighted size distribution. These findings demonstrate thatthe statistically significant difference between the DMM and the filter-based PM cannot just originate from the different measurement principles but also from the actual implementation of the combined aerodynamic-mobility measurement in the DMM. Optimizing the DMM will require changes in its design and/or the calculation algorithm to improve the resolution and width of the aerodynamic size distribution recorded.

  8. The evolution of automobile exhaust emission control

    SciTech Connect

    Taylor, K.C.

    1993-12-31

    Automobile catalytic converters have progressed from oxidation-only systems in the mid 1970`s to the current three-way catalytic converters which control emissions of carbon monoxide, hydrocarbons, and nitrogen oxide to very low levels. New exhaust emission regulations adopted Federally and in California which come into effect during the 1990`s once again demand new emission control system technology. A new generation of catalytic converter systems coupled with attention to fuel composition characterizes this third phase of exhaust emission control.

  9. Emission of carcinogenic components with automobile exhausts.

    PubMed Central

    Stenberg, U; Alsberg, T; Westerholm, R

    1983-01-01

    Different sampling methods for mutagenic polynuclear aromatic hydrocarbons (PAH) are described. These methods involve either direct sampling of raw exhausts which prior to filtering are cooled in a condenser, or filter sampling of exhausts diluted in a tunnel. The relevance of gas-phase PAHs of samples from diluted exhausts is discussed; methods used are either adsorbents (XAD-2) or cryogenic condensation. The emission of benzo(a)pyrene and certain other PAHs is reported from vehicles using different fuels (gasoline, diesel, LPG, alcohols) or different emission control systems. The emission of some volatiles, such as benzene, ethylene and alkylnitrites, is also presented from different types of fuels used. PMID:6186483

  10. Laboratory evaluation of a prototype photochemical chamber designed to investigate the health effects of fresh and aged vehicular exhaust emissions

    PubMed Central

    Papapostolou, Vasileios; Lawrence, Joy E.; Diaz, Edgar A.; Wolfson, Jack M.; Ferguson, Stephen T.; Long, Mark S.; Godleski, John J.; Koutrakis, Petros

    2013-01-01

    Laboratory experiments simulating atmospheric aging of motor vehicle exhaust emissions were conducted using a single vehicle and a photochemical chamber. A compact automobile was used as a source of emissions. The vehicle exhaust was diluted with ambient air to achieve carbon monoxide (CO) concentrations similar to those observed in an urban highway tunnel. With the car engine idling, it is expected that the CO concentration is a reasonable surrogate for volatile organic compounds (VOCs) emissions. Varying the amount of dilution of the exhaust gas to produce different CO concentrations, allowed adjustment of the concentrations of VOCs in the chamber to optimize production of secondary organic aerosol (SOA) needed for animal toxicological exposures. Photochemical reactions in the chamber resulted in nitric oxide (NO) depletion, nitrogen dioxide (NO2) formation, ozone (O3) accumulation, and SOA formation. A stable SOA concentration of approximately 40 µg m−3 at a chamber mean residence time of 30 min was achieved. This relatively short mean residence time provided adequate chamber flow output for both particle characterization and animal exposures. The chamber was operated as a continuous flow reactor for animal toxicological tests. SOA mass generated from the car exhaust diluted with ambient air was almost entirely in the ultrafine mode. Chamber performance was improved by using different types of seed aerosol to provide a surface for condensation of semivolatile reaction products, thus increasing the yield of SOA. Toxicological studies using Sprague-Dawley rats found significant increases of in vivo chemiluminescence in lungs following exposure to SOA. PMID:21689011

  11. Laboratory evaluation of a prototype photochemical chamber designed to investigate the health effects of fresh and aged vehicular exhaust emissions.

    PubMed

    Papapostolou, Vasileios; Lawrence, Joy E; Diaz, Edgar A; Wolfson, Jack M; Ferguson, Stephen T; Long, Mark S; Godleski, John J; Koutrakis, Petros

    2011-07-01

    Laboratory experiments simulating atmospheric aging of motor vehicle exhaust emissions were conducted using a single vehicle and a photochemical chamber. A compact automobile was used as a source of emissions. The vehicle exhaust was diluted with ambient air to achieve carbon monoxide (CO) concentrations similar to those observed in an urban highway tunnel. With the car engine idling, it is expected that the CO concentration is a reasonable surrogate for volatile organic compounds (VOCs) emissions. Varying the amount of dilution of the exhaust gas to produce different CO concentrations, allowed adjustment of the concentrations of VOCs in the chamber to optimize production of secondary organic aerosol (SOA) needed for animal toxicological exposures. Photochemical reactions in the chamber resulted in nitric oxide (NO) depletion, nitrogen dioxide (NO₂) formation, ozone (O₃) accumulation, and SOA formation. A stable SOA concentration of approximately 40 μg m⁻³ at a chamber mean residence time of 30 min was achieved. This relatively short mean residence time provided adequate chamber flow output for both particle characterization and animal exposures. The chamber was operated as a continuous flow reactor for animal toxicological tests. SOA mass generated from the car exhaust diluted with ambient air was almost entirely in the ultrafine mode. Chamber performance was improved by using different types of seed aerosol to provide a surface for condensation of semivolatile reaction products, thus increasing the yield of SOA. Toxicological studies using Sprague-Dawley rats found significant increases of in vivo chemiluminescence in lungs following exposure to SOA.

  12. Aircraft Piston Engine Exhaust Emission Symposium

    NASA Technical Reports Server (NTRS)

    1976-01-01

    A 2-day symposium on the reduction of exhaust emissions from aircraft piston engines was held on September 14 and 15, 1976, at the Lewis Research Center in Cleveland, Ohio. Papers were presented by both government organizations and the general aviation industry on the status of government contracts, emission measurement problems, data reduction procedures, flight testing, and emission reduction techniques.

  13. Mercaptans emissions in diesel and biodiesel exhaust

    NASA Astrophysics Data System (ADS)

    Corrêa, Sérgio Machado; Arbilla, Graciela

    Biodiesel and ethanol are fuels in clear growth and evidence, basically due to its relation with the greenhouse effect reduction. There are several works regarding regulated pollutants emissions, but there is a lack of reports in non-regulated emissions. In a previous paper (Corrêa and Arbilla, 2006) the emissions of aromatic hydrocarbons were reported and in 2007 another paper was published in 2008 focusing carbonyls emissions (Corrêa and Arbilla, 2008). In this work four mercaptans (methyl, ethyl, n-propyl and n-butyl mercaptans) were evaluated for a heavy-duty diesel engine, fueled with pure diesel (D) and biodiesel blends (v/v) of 2% (B2), 5% (B5), 10% (B10), and 20% (B20). The tests were carried using a six cylinder heavy-duty engine, typical of the Brazilian fleet of urban buses, during a real use across the city. The exhaust gases were diluted near 20 times and the mercaptans were sampled with glass fiber filters impregnated with mercuric acetate. The chemical analyses were performed by gas chromatography with mass spectrometry detection. The results indicated that the mercaptans emissions exhibit a reduction with the increase of biodiesel content, but this reduction is lower as the mercaptan molar mass increases. For B20 results the emission reduction was 18.4% for methyl mercaptan, 18.1% for ethyl mercaptan, 16.3% for n-propyl mercaptan, and 9.6% for n-butyl mercaptan.

  14. Reducing exhaust gas emissions from Citydiesel busses

    NASA Astrophysics Data System (ADS)

    Mikkonen, Seppo

    The effect of fuel composition and exhaust gas aftertreatment on the emissions was measured from truck and bus engines. Possibilities to measure unregulated emissions (aldehydes, polyaromatic hydrocarbons, mutagenicity) were built. A reformulated diesel fuel 'Citydiesel' was developed. Citydiesel was able to reduce emissions compared to standard diesel fuel as follows: particulates by 10 to 30%, nitrogen oxides by 2 to 10%, sulphur dioxide by 97%, polyaromatic hydrocarbons (PAH) over 50%, mutagenicity of the exhaust particulates clearly, odor of the exhaust, and smoke after a cold start. The use of Citydiesel fuel reduces emissions of the existing vehicles immediately which is a remarkable benefit. The very low sulphur content (below 50 ppm) makes it possible to use oxidation. catalytic converters to reduce emissions of diesel vehicles. The new Euro 2 exhaust regulations coming into force during 1996 can be met with a modern diesel engine, Citydiesel fuel, and exhaust gas aftertreatment. Properties of Citydiesel fuel were verified in a three year field test with 140 city buses. Experience was good; e.g., engine oil change interval could be lengthened. Total value of the exhaust was estimated with different fuels and aftertreatment device in order to find out cheap ways to reduce emissions.

  15. Evaluation of exhaust emissions from a Bi-fueled vehicle operating on liquid and gaseous fuels. Topical report, June-July 1995

    SciTech Connect

    Whitney, K.A.

    1995-12-01

    Exhaust emissions were characterized from a bi-fueled vehicle operating on compressed natural gas and two gasolines over a heavy acceleration/high speed driving cycle and during cold temperature operation. The test fuels included compressed natural gas (CNG) meeting California Air Resources Board emissions certification specifications, industry average gasoline formulated to the specifications of Reference Fuel A (RF-A) used in the CRC/Auto Oil program, and Federal reformulated gasoline (RFG) purchased at a commercial service station in metropolitan Houston. Exhaust emissions were evaluated over the light-duty chassis dynamometer portion of the Federal Test Procedure at 75 deg F and at 20 deg F, and the REP05 - a hot, stabilized, high speed, high acceleration driving cycle developed by the EPA to be representative of non-FTP, in-use driving. In addition, CNG emissions were evaluated over the US06 driving cycle. Average regulated exhaust emissions (total hydrocarbons, methane, carbon monoxide, and oxides of nitrogen) were evaluated in a manner consistent with the Code of Federal Regulations.

  16. 14 CFR 34.31 - Standards for exhaust emissions.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... FUEL VENTING AND EXHAUST EMISSION REQUIREMENTS FOR TURBINE ENGINE POWERED AIRPLANES Exhaust Emissions (In-use Aircraft Gas Turbine Engines) § 34.31 Standards for exhaust emissions. (a) Exhaust emissions of smoke from each in-use aircraft gas turbine engine of Class T8, beginning February 1, 1974, shall...

  17. 14 CFR 34.31 - Standards for exhaust emissions.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... FUEL VENTING AND EXHAUST EMISSION REQUIREMENTS FOR TURBINE ENGINE POWERED AIRPLANES Exhaust Emissions (In-use Aircraft Gas Turbine Engines) § 34.31 Standards for exhaust emissions. (a) Exhaust emissions of smoke from each in-use aircraft gas turbine engine of Class T8, beginning February 1, 1974,...

  18. 14 CFR 34.31 - Standards for exhaust emissions.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... FUEL VENTING AND EXHAUST EMISSION REQUIREMENTS FOR TURBINE ENGINE POWERED AIRPLANES Exhaust Emissions (In-use Aircraft Gas Turbine Engines) § 34.31 Standards for exhaust emissions. (a) Exhaust emissions of smoke from each in-use aircraft gas turbine engine of Class T8, beginning February 1, 1974,...

  19. 14 CFR 34.21 - Standards for exhaust emissions.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... FUEL VENTING AND EXHAUST EMISSION REQUIREMENTS FOR TURBINE ENGINE POWERED AIRPLANES Exhaust Emissions (New Aircraft Gas Turbine Engines) § 34.21 Standards for exhaust emissions. (a) Exhaust emissions of smoke from each new aircraft gas turbine engine of class T8 manufactured on or after February 1,...

  20. Status of German European exhaust emission legislation

    SciTech Connect

    Seiffert, U.

    1985-01-01

    Recent legislative initiatives in West Germany and other European countries are leading to more stringent automobile exhaust emission standards. A review of the emission inventory on a global and West German basis and other factors, such as acid rain and forest damage, indicate that the contribution of automobile exhaust to the emission problem may be less than the European public assumes. As an interim step while new standards are being considered, the West German government is promoting the purchase of low-pollution vehicles through a vehicle tax reduction program.

  1. Characterization of nitromethane emission from automotive exhaust

    NASA Astrophysics Data System (ADS)

    Sekimoto, Kanako; Inomata, Satoshi; Tanimoto, Hiroshi; Fushimi, Akihiro; Fujitani, Yuji; Sato, Kei; Yamada, Hiroyuki

    2013-12-01

    We carried out time-resolved experiments using a proton-transfer-reaction mass spectrometer and a chassis dynamometer to characterize nitromethane emission from automotive exhaust. We performed experiments under both cold-start and hot-start conditions, and determined the dependence of nitromethane emission on vehicle velocity and acceleration/deceleration as well as the effect of various types of exhaust-gas treatment system. We found that nitromethane emission was much lower from a gasoline car than from diesel trucks, probably due to the reduction function of the three-way catalyst of the gasoline car. Diesel trucks without a NOx reduction catalyst using hydrocarbons produced high emissions of nitromethane, with emission factors generally increasing with increasing acceleration at low vehicle velocities.

  2. 40 CFR 87.31 - Standards for exhaust emissions.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... Gas Turbine Engines) § 87.31 Standards for exhaust emissions. (a) Exhaust emissions of smoke from each in-use aircraft gas turbine engine of Class T8, beginning February 1, 1974, shall not exceed: Smoke number of 30. (b) Exhaust emissions of smoke from each in-use aircraft gas turbine engine of class TF...

  3. 40 CFR 87.31 - Standards for exhaust emissions.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... Gas Turbine Engines) § 87.31 Standards for exhaust emissions. (a) Exhaust emissions of smoke from each in-use aircraft gas turbine engine of Class T8, beginning February 1, 1974, shall not exceed: Smoke number of 30. (b) Exhaust emissions of smoke from each in-use aircraft gas turbine engine of class TF...

  4. 40 CFR 87.31 - Standards for exhaust emissions.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... (CONTINUED) Definitions. Exhaust Emissions (In-Use Aircraft Gas Turbine Engines) § 87.31 Standards for exhaust emissions. (a) Exhaust emissions of smoke from each in-use aircraft gas turbine engine of Class T8... in-use aircraft gas turbine engine of class TF and of rated output of 129 kilonewtons thrust or...

  5. Exhaustion, a guide to transportation emissions

    SciTech Connect

    1998-10-01

    This publication contains a series of fact sheets on the environmental impact of the automobile, addressing the issues of vehicle exhaust and its impact, alternative and cleaner fuels, and alternative forms of transportation. The sheets are intended to serve as background information and reference material. Specific topics of the sheets include: Components of car exhaust and other automobile-related emissions; air quality in Canada; smog; climate change and the greenhouse effect; acid rain; stratospheric ozone depletion; hazardous air pollutants and the automobile; health impacts; modifications and improvements to diesel fuels; reformulated gasoline; alternative fuels such as propane, ethanol, natural gas, hydrogen, and methanol; emissions standards and controls; inspection and maintenance programs; transportation demand management; driving behavior and the environment; and indirect costs of the automobile.

  6. [Emission Factors of Vehicle Exhaust in Beijing].

    PubMed

    Fan, Shou-bin; Tian, Ling-di; Zhang, Dong-xu; Qu, Song

    2015-07-01

    Based on the investigation of basic data such as vehicle type composition, driving conditions, ambient temperature and oil quality, etc., emission factors of vehicle exhaust pollutants including carbon monoxide (CO), nitrogen oxides (NOx), hydrocarbons (HC) and particulate matter(PM) were calculated using COPERT IV model. Emission factors of typical gasoline passenger cars and diesel trucks were measured using on-board measurement system on actual road. The measured and modeled emission factors were compared and the results showed that: the measured emission factors of CO, NOx and HC were 0. 96, 0. 64 and 4. 89 times of the modeled data for passenger cars conforming to the national IV emission standard. For the light, medium and heavy diesel trucks conforming to the national III emission standard, the measured data of CO emission factors were 1.61, 1. 07 and 1.76 times of the modeled data, respectively, the measured data of NOx emission factors were 1. 04, 1. 21 and 1. 18 times of the modeled data, and the measured data of HC emission factors were 3. 75, 1. 84 and 1. 47 times of the modeled data, while the model data of PM emission factors were 1. 31, 3. 42 and 6. 42 times of the measured data, respectively.

  7. Exhaust emissions from high speed passenger ferries

    NASA Astrophysics Data System (ADS)

    Cooper, D. A.

    Exhaust emission measurements have been carried out on-board three high-speed passenger ferries (A, B and C) during normal service routes. Ship A was powered by conventional, medium-speed, marine diesel engines, Ship B by gas turbine engines and Ship C conventional, medium-speed, marine diesel engines equipped with selective catalytic reduction (SCR) systems for NO x abatement. All ships had similar auxiliary engines (marine diesels) for generating electric power on-board. Real-world emission factors of NOx, SO2, CO, CO 2, NMVOC, CH4, N2O, NH3, PM and PAH at steady-state engine loads and for complete voyages were determined together with an estimate of annual emissions. In general, Ship B using gas turbines showed favourable NO x, PM and PAH emissions but at the expense of higher fuel consumption and CO 2 emissions. Ship C with the SCR had the lowest NO x emissions but highest NH 3 emissions especially during harbour approaches and stops. The greatest PM and PAH specific emissions were measured from auxiliary engines operating at low engine loads during harbour stops. Since all ships used a low-sulphur gas oil, SO 2 emissions were relatively low in all cases.

  8. Tumorigenesis of diesel exhaust, gasoline exhaust, and related emission extracts on SENCAR mouse skin

    SciTech Connect

    Nesnow, S; Triplett, L L; Slaga, T J

    1980-01-01

    The tumorigenicity of diesel exhaust particulate emissions was examined using a sensitive mouse skin tumorigenesis model (SENCAR). The tumorigenic potency of particulate emissions from diesel, gasoline, and related emission sources was compared.

  9. Photocatalytic destruction of automobile exhaust emissions

    SciTech Connect

    Kaviranta, P.D.; Peden, C.H.F.

    1996-10-01

    Hydrocarbons, carbon monoxide, and nitrogen oxides contained in automobile exhaust emissions are among the major atmospheric air pollutants. During the first few minutes of a cold start of the engine, the emission levels of unburned hydrocarbon and CO pollutants are very high due to the inefficiency of the cold engine and the poor activity of the catalysts lower temperatures. Therefore, it is necessary to provide an alternative approach to deal with this specific problem in order to meet near-term regulatory requirements. Our approach has been to use known photocatalytic reactions obtainable on semiconducting powders such as titanium dioxide. In this presentation we describe our recent studies aimed at the photocatalytic reduction of unburned hydrocarbons and carbon monoxide in automobile exhaust emissions. Our results demonstrate the effective destruction of propylene into water and carbon dioxide. The conversion was found to be dependent on the propylene flow rate. The reaction rate was studied as a function of time, humidity and temperature. The effect of the power of the UV source on conversion will also be presented.

  10. 40 CFR 86.1544 - Calculation; idle exhaust emissions.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 19 2010-07-01 2010-07-01 false Calculation; idle exhaust emissions. 86.1544 Section 86.1544 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... Test Procedures § 86.1544 Calculation; idle exhaust emissions. (a) The final idle emission test...

  11. Vehicle's exhaust emissions under car-following model

    NASA Astrophysics Data System (ADS)

    Tang, Tie-Qiao; Li, Jin-Gang; Zhang, Dong; Wang, Yun-Peng

    2014-12-01

    In this paper, we explore each vehicle's exhaust emissions under the full velocity difference (FVD) model and the car-following model with consideration of the traffic interruption probability during three typical traffic situations. Numerical results show that the vehicle's exhaust emissions of the second model are less than those of the first model under the three typical traffic situations, which shows that the second model can reduce each vehicle's exhaust emissions.

  12. Exhaust emission reduction for intermittent combustion aircraft engines

    NASA Technical Reports Server (NTRS)

    Moffett, R. N.

    1979-01-01

    Three concepts for optimizing the performance, increasing the fuel economy, and reducing exhaust emission of the piston aircraft engine were investigated. High energy-multiple spark discharge and spark plug tip penetration, ultrasonic fuel vaporization, and variable valve timing were evaluated individually. Ultrasonic fuel vaporization did not demonstrate sufficient improvement in distribution to offset the performance loss caused by the additional manifold restriction. High energy ignition and revised spark plug tip location provided no change in performance or emissions. Variable valve timing provided some performance benefit; however, even greater performance improvement was obtained through induction system tuning which could be accomplished with far less complexity.

  13. 14 CFR 34.31 - Standards for exhaust emissions.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... of smoke from each in-use aircraft gas turbine engine of Class T8, beginning February 1, 1974, shall not exceed a smoke number (SN) of 30. (b) Exhaust emissions of smoke from each in-use aircraft gas... paragraphs (a) and (b) of this section refer to exhaust smoke emission emitted during operation of the...

  14. 14 CFR 34.31 - Standards for exhaust emissions.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... of smoke from each in-use aircraft gas turbine engine of Class T8, beginning February 1, 1974, shall not exceed a smoke number (SN) of 30. (b) Exhaust emissions of smoke from each in-use aircraft gas... paragraphs (a) and (b) of this section refer to exhaust smoke emission emitted during operation of the...

  15. Measuring soot particles from automotive exhaust emissions

    NASA Astrophysics Data System (ADS)

    Andres, Hanspeter; Lüönd, Felix; Schlatter, Jürg; Auderset, Kevin; Jordan-Gerkens, Anke; Nowak, Andreas; Ebert, Volker; Buhr, Egbert; Klein, Tobias; Tuch, Thomas; Wiedensohler, Alfred; Mamakos, Athanasios; Riccobono, Francesco; Discher, Kai; Högström, Richard; Yli-Ojanperä, Jaakko; Quincey, Paul

    2014-08-01

    The European Metrology Research Programme participating countries and the European Union jointly fund a three year project to address the need of the automotive industry for a metrological sound base for exhaust measurements. The collaborative work on particle emissions involves five European National Metrology Institutes, the Tampere University of Technology, the Joint Research Centre for Energy and Transport and the Leibniz Institute for Tropospheric Research. On one hand, a particle number and size standard for soot particles is aimed for. Eventually this will allow the partners to provide accurate and comparable calibrations of measurement instruments for the type approval of Euro 5b and Euro 6 vehicles. Calibration aerosols of combustion particles, silver and graphite proof partially suitable. Yet, a consensus choice together with instrument manufactures is pending as the aerosol choice considerably affects the number concentration measurement. Furthermore, the consortium issued consistent requirements for novel measuring instruments foreseen to replace today's opacimeters in regulatory periodic emission controls of soot and compared them with European legislative requirements. Four partners are conducting a metrological validation of prototype measurement instruments. The novel instruments base on light scattering, electrical, ionisation chamber and diffusion charging sensors and will be tested at low and high particle concentrations. Results shall allow manufacturers to further improve their instruments to comply with legal requirements.

  16. Effects of fuel type, driving cycle, and emission status on in-use vehicle exhaust reactivity.

    PubMed

    Ho, J; Winer, A M

    1998-07-01

    The introduction of reformulated gasolines significantly reduced exhaust hydrocarbon (HC) mass emissions, but few data are available concerning how these new fuels affect exhaust reactivity. Similarly, while it is well established that high-emitting vehicles contribute a significant portion of total mobile source HC mass emissions, it is also important to evaluate the exhaust reactivity from these vehicles. The objective of this study was to evaluate the relative influence on in-use vehicle exhaust reactivity of three critical factors: fuel, driving cycle, and vehicle emission status. Nineteen in-use vehicles were tested with seven randomly assigned fuel types and two driving cycles: the Federal Test Procedure (FTP) and the Unified Cycle (UC). Total exhaust reactivity was not statistically different between the FTP and UC cycles but was significantly affected by fuel type. On average, the exhaust reactivity for California Phase 2 fuel was the lowest (16% below the highest fuel type) among the seven fuels tested for cold start emissions. The average exhaust reactivity for high-emitting vehicles was significantly higher for hot stabilized (11%) and hot start (15%) emissions than for low-emitting vehicles. The exhaust reactivities for the FTP and UC cycles for light-end HCs and carbonyls were significantly different for the hot stabilized mode. There was a significant fuel effect on the mean specific reactivity (SR) for the mid-range HCs, but not for light-end HCs or carbonyls, while vehicle emission status affected the mean SR for all three HC compound classes.

  17. 14 CFR 34.64 - Sampling and analytical procedures for measuring gaseous exhaust emissions.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT FUEL VENTING AND EXHAUST EMISSION REQUIREMENTS FOR TURBINE... Turbine Engines) § 34.64 Sampling and analytical procedures for measuring gaseous exhaust emissions....

  18. 14 CFR 34.64 - Sampling and analytical procedures for measuring gaseous exhaust emissions.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT FUEL VENTING AND EXHAUST EMISSION REQUIREMENTS FOR TURBINE... Turbine Engines) § 34.64 Sampling and analytical procedures for measuring gaseous exhaust emissions....

  19. Exhaust system with emissions storage device and plasma reactor

    DOEpatents

    Hoard, John W.

    1998-01-01

    An exhaust system for a combustion system, comprising a storage device for collecting NO.sub.x, hydrocarbon, or particulate emissions, or mixture of these emissions, and a plasma reactor for destroying the collected emissions is described. After the emission is collected in by the storage device for a period of time, the emission is then destroyed in a non-thermal plasma generated by the plasma reactor. With respect to the direction of flow of the exhaust stream, the storage device must be located before the terminus of the plasma reactor, and it may be located wholly before, overlap with, or be contained within the plasma reactor.

  20. Evolution of on-road vehicle exhaust emissions in Delhi

    NASA Astrophysics Data System (ADS)

    Goel, Rahul; Guttikunda, Sarath K.

    2015-03-01

    For a 40-year horizon (1990-2030), on-road vehicle exhaust emissions were evaluated, retrospectively and prospectively, for the largest urban agglomeration in India - the Greater Delhi region with a combined population of 22 million in 2011 (Delhi along with Ghaziabad, Noida, Greater Noida, Faridabad and Gurgaon). Emissions of particulate matter, sulfur dioxide, carbon monoxide and volatile organic compounds (VOCs) reached their peak during late 1990s through early 2000s after which they reduced significantly through year 2012. On the other hand, nitrogen oxides (NOx) and carbon dioxide show an increasing trend. The most reduction in emissions between 1998 and 2012 occurred as a result of implementation of four sets of vehicular emission standards, removal of lead, reduction of sulfur content, mandatory retirement of older commercial vehicles, and conversion of diesel and petrol run public transport vehicles to compressed natural gas. In addition, changes in the vehicular technology have also contributed to controlling emissions especially in case of auto-rickshaws and motorized two-wheelers, which changed from two-stroke to four-stroke. The rising trend of NOx along with the presence of VOCs indicates increasing tendency to form ground-level ozone and as a result, smog in the region. We predict that the current regime of vehicle technology, fuel standards, and high growth rate of private vehicles, is likely to nullify all the past emission reductions by the end of 2020s.

  1. Measurement of automobile exhaust emissions under realistic road conditions

    SciTech Connect

    Staab, J.; Schurmann, D.

    1987-01-01

    An exhaust gas measurement system for on-board use has been developed, which enables the direct and continuous determination of the exhaust mass emissions in vehicles on the road. Such measurements under realistic traffic conditions are a valuable supplement to measurements taken on test benches, the latter, however, still being necessary. In the last two years numerous test runs were undertaken. The reliability of the on-board system could be demonstrated and a very informative view of the exhaust emissions behavior of a vehicle on the road was obtained from the test results.

  2. Further exhaust emission control for two-stroke engines

    SciTech Connect

    Sato, Kazuo; Nakano, Masamitsu; Ukawa, Haruo; Inaga, Hisashi

    1994-09-01

    Two-stroke engines are being utilized in large numbers as small utility, lawn and garden equipment engines. The following two subjects were examined with regards to exhaust emission control. The first subject was to compare the theoretical values of a combustion model simulation with the experimentally measured values of the base line emission of two-stroke volume. The second subject was to examine the emission conformability to the 1995 and 1999 California Air Resources Board (CARB) exhaust emission regulations California Regulations for 1995 and Later Utility and Lawn and Garden Equipment Engine, adopted at March 20, 1992, amended, at November 3, 1993. in two-stroke engines with various combinations between various fuels, fuel supply systems and scavenging systems. For this subject it was determine;that the emission control systems based on the lean combustion can be used to meet the 1995 CARB exhaust emission regulations. However, it was also concluded that to meet the 1999 CARB exhaust emission regulations, various emission control systems with various combinations regarding such parameters as fuels, scavenging systems and exhaust systems must be used. 27 refs., 20 figs., 4 tabs.

  3. Non-exhaust PM emissions from electric vehicles

    NASA Astrophysics Data System (ADS)

    Timmers, Victor R. J. H.; Achten, Peter A. J.

    2016-06-01

    Particulate matter (PM) exposure has been linked to adverse health effects by numerous studies. Therefore, governments have been heavily incentivising the market to switch to electric passenger cars in order to reduce air pollution. However, this literature review suggests that electric vehicles may not reduce levels of PM as much as expected, because of their relatively high weight. By analysing the existing literature on non-exhaust emissions of different vehicle categories, this review found that there is a positive relationship between weight and non-exhaust PM emission factors. In addition, electric vehicles (EVs) were found to be 24% heavier than equivalent internal combustion engine vehicles (ICEVs). As a result, total PM10 emissions from EVs were found to be equal to those of modern ICEVs. PM2.5 emissions were only 1-3% lower for EVs compared to modern ICEVs. Therefore, it could be concluded that the increased popularity of electric vehicles will likely not have a great effect on PM levels. Non-exhaust emissions already account for over 90% of PM10 and 85% of PM2.5 emissions from traffic. These proportions will continue to increase as exhaust standards improve and average vehicle weight increases. Future policy should consequently focus on setting standards for non-exhaust emissions and encouraging weight reduction of all vehicles to significantly reduce PM emissions from traffic.

  4. Two stroke engine exhaust emissions separator

    DOEpatents

    Turner, Terry D.; Wilding, Bruce M.; McKellar, Michael G.; Raterman, Kevin T.

    2002-01-01

    A separator for substantially resolving at least one component of a process stream, such as from the exhaust of an internal combustion engine. The separator includes a body defining a chamber therein. A nozzle housing is located proximate the chamber. An exhaust inlet is in communication with the nozzle housing and the chamber. A nozzle assembly is positioned in the nozzle housing and includes a nozzle moveable within and relative to the nozzle housing. The nozzle includes at least one passage formed therethrough such that a process stream entering the exhaust inlet connection passes through the passage formed in the nozzle, which imparts a substantially rotational flow to the process stream as it enters the chamber. A positioning member is configured to position the nozzle relative to the nozzle housing in response to changes in process stream pressure to adjust flowrate of said process stream entering into the chamber.

  5. Two stroke engine exhaust emissions separator

    DOEpatents

    Turner, Terry D.; Wilding, Bruce M.; McKellar, Michael G.; Raterman, Kevin T.

    2003-04-22

    A separator for substantially resolving at least one component of a process stream, such as from the exhaust of an internal combustion engine. The separator includes a body defining a chamber therein. A nozzle housing is located proximate the chamber. An exhaust inlet is in communication with the nozzle housing and the chamber. A nozzle assembly is positioned in the nozzle housing and includes a nozzle moveable within and relative to the nozzle housing. The nozzle includes at least one passage formed therethrough such that a process stream entering the exhaust inlet connection passes through the passage formed in the nozzle and imparts a substantially rotational flow to the process stream as it enters the chamber. A positioning member is configured to position the nozzle relative to the nozzle housing in response to changes in process stream pressure thereby adjusting flowrate of said process stream entering into the chamber.

  6. Evaluation of Exhaust Emissions from Three Diesel-Hybrid Cars and Simulation of After-Treatment Systems for Ultralow Real-World NOx Emissions.

    PubMed

    Franco, Vicente; Zacharopoulou, Theodora; Hammer, Jan; Schmidt, Helge; Mock, Peter; Weiss, Martin; Samaras, Zissis

    2016-12-06

    Hybridization offers great potential for decreasing pollutant and carbon dioxide emissions of diesel cars. However, an assessment of the real-world emissions performance of modern diesel hybrids is missing. Here, we test three diesel-hybrid cars on the road and benchmark our findings with two cars against tests on the chassis dynamometer and model simulations. The pollutant emissions of the two cars tested on the chassis dynamometer were in compliance with the relevant Euro standards over the New European Driving Cycle and Worldwide harmonized Light vehicles Test Procedure. On the road, all three diesel-hybrids exceeded the regulatory NOx limits (average exceedance for all trips: +150% for the Volvo, +510% for the Peugeot, and +550% for the Mercedes-Benz) and also showed elevated on-road CO2 emissions (average exceedance of certification values: +178, +77, and +52%, respectively). These findings point to a wide discrepancy between certified and on-road CO2 and suggest that hybridization alone is insufficient to achieve low-NOx emissions of diesel powertrains. Instead, our simulation suggests that properly calibrated selective catalytic reduction filter and lean-NOx trap after-treatment technologies can reduce the on-road NOx emissions to 0.023 and 0.068 g/km on average, respectively, well below the Euro 6 limit (0.080 g/km).

  7. 40 CFR 94.8 - Exhaust emission standards.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... for Compression-Ignition Marine Engines § 94.8 Exhaust emission standards. (a) The Tier 1 standards of.... (1) Tier 1 standards. NOX emissions from model year 2004 and later engines with displacement of 2.5... speed is less than 130 rpm. (ii) 45.0 × N−0.20 when maximum test speed is at least 130 but less...

  8. 40 CFR 86.1544 - Calculation; idle exhaust emissions.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... Natural Gas-Fueled, and Liquefied Petroleum Gas-Fueled Diesel-Cycle Light-Duty Trucks; Idle Test Procedures § 86.1544 Calculation; idle exhaust emissions. (a) The final idle emission test results shall be reported as percent for carbon monoxide on a dry basis. (b) If a CVS sampling system is used, the...

  9. Exhaust emissions reduction for intermittent combustion aircraft engines

    NASA Technical Reports Server (NTRS)

    Rezy, B. J.; Stuckas, K. J.; Tucker, J. R.; Meyers, J. E.

    1982-01-01

    Three concepts which, to an aircraft piston engine, provide reductions in exhaust emissions of hydrocarbons and carbon monoxide while simultaneously improving fuel economy. The three chosen concepts, (1) an improved fuel injection system, (2) an improved cooling cylinder head, and (3) exhaust air injection, when combined, show a synergistic relationship in achieving these goals. In addition, the benefits of variable ignition timing were explored and both dynamometer and flight testing of the final engine configuration were accomplished.

  10. Exhaust emissions from ships at berth

    NASA Astrophysics Data System (ADS)

    Cooper, D. A.

    Emission measurements have been carried out on board six ships at berth during normal real-world operation (hotelling, unloading and loading activities). The study included three passenger ferries, one transoceanic container/ro-ro, one transoceanic car/truck carrier, and one chemical tanker. Emissions were measured from 22 auxiliary engines (AEs, medium and high-speed marine diesels) covering seven engine models and ranging in size from 720 to 2675 kW maximum output. The fuels varied from low sulphur gasoils ( 2.91 cst viscosity) through to residual oils ( 411 cst viscosity). Both specific emission factors ( g kWh -1) at a given engine load and total emissions (kg) of nitrogen oxides (NO x), sulphur dioxide, carbon monoxide, hydrocarbons, carbon dioxide, particulate matter (PM) and polyaromatic hydrocarbons during actual harbour stops were determined. In addition, some preliminary measurements to investigate PM size distributions were undertaken. The specific emissions showed significant variations between the different engine models and also within the same engine model on board the same ship. For example NO x emissions varied between 9.6 and 20.2 g kWh corr-1 between all engines and 14.2- 18.6 g kWh corr-1 between engines of the same model and fuel. Other emissions from boiler use and possible main engine warm-up prior to departure were in general expected to be considerably less than those from the AEs. The results obtained for the three passenger ferries demonstrate that empirically derived, emission formulae using dead weight tonnage can prove to be a cost-effective and accurate tool for harbour emission inventories.

  11. Controlling automotive exhaust emissions: successes and underlying science.

    PubMed

    Twigg, Martyn V

    2005-04-15

    Photochemical reactions of vehicle exhaust pollutants were responsible for photochemical smog in many cities during the 1960s and 1970s. Engine improvements helped, but additional measures were needed to achieve legislated emissions levels. First oxidation catalysts lowered hydrocarbon and carbon monoxide, and later nitrogen oxides were reduced to nitrogen in a two-stage process. By the 1980s, exhaust gas could be kept stoichiometric and hydrocarbons, carbon monoxide and nitrogen oxides were simultaneously converted over a single 'three-way catalyst'. Today, advanced three-way catalyst systems emissions are exceptionally low. NOx control from lean-burn engines demands an additional approach because NO cannot be dissociated under lean conditions. Current lean-burn gasoline engine NOx control involves forming a nitrate phase and periodically enriching the exhaust to reduce it to nitrogen, and this is being modified for use on diesel engines. Selective catalytic reduction with ammonia is an alternative that can be very efficient, but it requires ammonia or a compound from which it can be obtained. Diesel engines produce particulate matter, and, because of health concerns, filtration processes are being introduced to control these emissions. On heavy duty diesel engines the exhaust gas temperature is high enough for NO in the exhaust to be oxidised over a catalyst to NO2 that smoothly oxidises particulate material (PM) in the filter. Passenger cars operate at lower temperatures, and it is necessary to periodically burn the PM in air at high temperatures.

  12. Utilization of LPG and gasoline engine exhaust emissions by microalgae.

    PubMed

    Taştan, Burcu Ertit; Duygu, Ergin; Ilbaş, Mustafa; Dönmez, Gönül

    2013-02-15

    The effect of engine exhaust emissions on air pollution is one of the greatest problems that the world is facing today. The study focused on the effects of realistic levels of engine exhaust emissions of liquid petroleum gas (LPG) and gasoline (GSN) on Phormidium sp. and Chlorella sp. Multi parameters including pH, different medial compositions, fuel types, flow rates and biomass concentrations were described in detail. Effects of some growth factors such as triacontanol (TRIA) and salicylic acid (SA) have also been tested. The maximum biomass concentration of Phormidium sp. reached after 15 days at 0.36 and 0.15 g/L initial biomass concentrations were found as 1.160 g/L for LPG emission treated cultures and 1.331 g/L for GSN emission treated cultures, respectively. The corresponding figures were 1.478 g/L for LPG emission treated cultures and 1.636 g/L for GSN emission treated cultures at 0.65 and 0.36 g/L initial Chlorella sp. biomass concentrations. This study highlights the significance of using Phormidium sp. and Chlorella sp. for utilization of LPG and GSN engine exhaust emissions by the help of growth factors.

  13. Effects of vehicle exhaust emissions on urban wild plant species.

    PubMed

    Bell, J N B; Honour, S L; Power, S A

    2011-01-01

    Very few investigations have examined the direct impacts of vehicle exhausts on plants and attempted to separate out the key pollutants responsible for observed effects. This paper describes a multi-phase investigation into this topic, using 12 herbaceous species typical of urban areas and representing different functional groups. Fumigations were conducted in solardomes with diesel exhaust pollutants at concentrations designed to simulate those close to a major highway in inner London. A wide range of effects were detected, including growth stimulation and inhibition, changes in gas exchange and premature leaf senescence. This was complemented by controlled fumigations with NO, NO(2) and their mixture, as well as a transect study away from a busy inner London road. All evidence suggested that NO(x) was the key phytotoxic component of exhaust emissions, and highlights the potential for detrimental effects of vehicle emissions on urban ecosystems. Copyright © 2011 Elsevier Ltd. All rights reserved.

  14. Catalytic control of mutagenic exhaust emissions from gasoline passenger cars

    SciTech Connect

    Cooper, B.J.; Shore, P.R.

    1989-01-01

    Extracts of exhaust emissions from passenger cars equipped with conventional and lean-burn gasoline engines were tested for PAHs, NPAHs and mutagenicity. When installed with an appropriate three-way or oxidation catalyst very large reductions in each of these measurements were observed. Engine exhaust emissions contain hydrocarbons which are potentially hazardous to human health. Although there is an extensive database on the levels of mutagenic hydrocarbons in diesel particulate, much less data are available for modern gasoline engines. The study discussed in this paper addresses this with particular reference to the effect of exhaust catalysts on potentially harmful hydrocarbon species emitted by conventional and lean-burn gasoline engines. The effects over the European Extra-Urban Cycle are also addressed.

  15. 40 CFR 86.244-94 - Calculations; exhaust emissions.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... relevant pollutant, i.e., THC, CO, THCE, NMHC, NMHCE, CH4, NOX, and CO2 in grams per vehicle mile. ... 40 Protection of Environment 19 2013-07-01 2013-07-01 false Calculations; exhaust emissions. 86.244-94 Section 86.244-94 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED)...

  16. 40 CFR 86.244-94 - Calculations; exhaust emissions.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... relevant pollutant, i.e., THC, CO, THCE, NMHC, NMHCE, CH4, NOX, and CO2 in grams per vehicle mile. ... 40 Protection of Environment 18 2011-07-01 2011-07-01 false Calculations; exhaust emissions. 86.244-94 Section 86.244-94 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED)...

  17. 40 CFR 86.244-94 - Calculations; exhaust emissions.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... relevant pollutant, i.e., THC, CO, THCE, NMHC, NMHCE, CH4, NOX, and CO2 in grams per vehicle mile. ... 40 Protection of Environment 19 2012-07-01 2012-07-01 false Calculations; exhaust emissions. 86.244-94 Section 86.244-94 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED)...

  18. 40 CFR 86.244-94 - Calculations; exhaust emissions.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 18 2010-07-01 2010-07-01 false Calculations; exhaust emissions. 86.244-94 Section 86.244-94 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... New Medium-Duty Passenger Vehicles; Cold Temperature Test Procedures § 86.244-94 Calculations;...

  19. Particulate exhaust emissions from an experimental combustor. [gas turbine engine

    NASA Technical Reports Server (NTRS)

    Norgren, C. T.; Ingebo, R. D.

    1975-01-01

    The concentration of dry particulates (carbon) in the exhaust of an experimental gas turbine combustor was measured at simulated takeoff operating conditions and correlated with the standard smoke-number measurement. Carbon was determined quantitatively from a sample collected on a fiberglass filter by converting the carbon in the smoke sample to carbon dioxide and then measuring the volume of carbon dioxide formed by gas chromatography. At a smoke of 25 (threshold of visibility of the smoke plume for large turbojets) the carbon concentration was 2.8 mg carbon/cu m exhaust gas, which is equivalent to an emission index of 0.17 g carbon/kg fuel.

  20. Concepts for reducing exhaust emissions and fuel consumption of the aircraft piston engine

    NASA Technical Reports Server (NTRS)

    Rezy, B. J.; Stuckas, K. J.; Tucker, J. R.; Meyers, J. E.

    1979-01-01

    A study was made to reduce exhaust emissions and fuel consumption of a general aviation aircraft piston engine by applying known technology. Fourteen promising concepts such as stratified charge combustion chambers, cooling cylinder head improvements, and ignition system changes were evaluated for emission reduction and cost effectiveness. A combination of three concepts, improved fuel injection system, improved cylinder head with exhaust port liners and exhaust air injection was projected as the most cost effective and safe means of meeting the EPA standards for CO, HC and NO. The fuel economy improvement of 4.6% over a typical single engine aircraft flight profile does not though justify the added cost of the three concepts, and significant reductions in fuel consumption must be applied to the cruise mode where most of the fuel is used. The use of exhaust air injection in combination with exhaust port liners reduces exhaust valve stem temperatures which can result in longer valve guide life. The use of exhaust port liners alone can reduce engine cooling air requirements by 11% which is the equivalent of a 1.5% increase in propulsive power. The EPA standards for CO, HC and NO can be met in the IO-520 engine using air injection alone or the Simmonds improved fuel injection system.

  1. Exhaust gas emissions of a vortex breakdown stabilized combustor

    NASA Technical Reports Server (NTRS)

    Yetter, R. A.; Gouldin, F. C.

    1976-01-01

    Exhaust gas emission data are described for a swirl stabilized continuous combustor. The combustor consists of confined concentric jets with premixed fuel and air in the inner jet and air in the outer jet. Swirl may be induced in both inner and outer jets with the sense of rotation in the same or opposite directions (co-swirl and counter-swirl). The combustor limits NO emissions by lean operation without sacrificing CO and unburned hydrocarbon emission performance, when commercial-grade methane and air fired at one atmosphere without preheat are used. Relative swirl direction and magnitude are found to have significant effects on exhaust gas concentrations, exit temperatures, and combustor efficiencies. Counter-swirl gives a large recirculation zone, a short luminous combustion zone, and large slip velocities in the interjet shear layer. For maximum counter-swirl conditions, the efficiency is low.

  2. Exhaust constituent emission factors of printed circuit board pyrolysis processes and its exhaust control.

    PubMed

    Chiang, Hung-Lung; Lin, Kuo-Hsiung

    2014-01-15

    The printed circuit board (PCB) is an important part of electrical and electronic equipment, and its disposal and the recovery of useful materials from waste PCBs (WPCBs) are key issues for waste electrical and electronic equipment. Waste PCB compositions and their pyrolysis characteristics were analyzed in this study. In addition, the volatile organic compound (VOC) exhaust was controlled by an iron-impregnated alumina oxide catalyst. Results indicated that carbon and oxygen were the dominant components (hundreds mg/g) of the raw materials, and other elements such as nitrogen, bromine, and copper were several decades mg/g. Exhaust constituents of CO, H2, CH4, CO2, and NOx, were 60-115, 0.4-4.0, 1.1-10, 30-95, and 0-0.7mg/g, corresponding to temperatures ranging from 200 to 500°C. When the pyrolysis temperature was lower than 300°C, aromatics and paraffins were the major species, contributing 90% of ozone precursor VOCs, and an increase in the pyrolysis temperature corresponded to a decrease in the fraction of aromatic emission factors. Methanol, ethylacetate, acetone, dichloromethane, tetrachloromethane and acrylonitrile were the main species of oxygenated and chlorinated VOCs. The emission factors of some brominated compounds, i.e., bromoform, bromophenol, and dibromophenol, were higher at temperatures over 400°C. When VOC exhaust was flowed through the bed of Fe-impregnated Al2O3, the emission of ozone precursor VOCs could be reduced by 70-80%.

  3. Particulate Measurements and Emissions Characterization of Alternative Fuel Vehicle Exhaust

    SciTech Connect

    Durbin, T. D.; Truex, T. J.; Norbeck, J. M.

    1998-11-19

    The objective of this project was to measure and characterize particulate emissions from light-duty alternative fuel vehicles (AFVs) and equivalent gasoline-fueled vehicles. The project included emission testing of a fleet of 129 gasoline-fueled vehicles and 19 diesel vehicles. Particulate measurements were obtained over Federal Test Procedure and US06 cycles. Chemical characterization of the exhaust particulate was also performed. Overall, the particulate emissions from modern technology compressed natural gas and methanol vehicles were low, but were still comparable to those of similar technology gasoline vehicles.

  4. Exhaust emissions of a double annular combustor: Parametric study

    NASA Technical Reports Server (NTRS)

    Schultz, D. F.

    1974-01-01

    A full scale double-annular ram-induction combustor designed for Mach 3.0 cruise operation was tested. Emissions of oxides of nitrogen, carbon monoxide, unburned hydrocarbons, and smoke were measured over a range of combustor operating variables including reference velocity, inlet air temperature and pressure, and exit average temperature. ASTM Jet-A fuel was used for these tests. An equation is provided relating oxides of nitrogen emissions as a function of the combustor, operating variables. A small effect of radial fuel staging on reducing exhaust emissions (which were originally quite low) is demonstrated.

  5. Performance Evaluation of Kitchen Exhaust Draft Hoods.

    DTIC Science & Technology

    1980-03-01

    1-ACI827 JOHNS - MANVILLE SALES CORP DENVER CO RESEARCH AND DEV-ETC F/e 13/1 PERFORMANCE EVALUATION OF KITCHEN EXHAUST DRAFT HOOOS. (U) MAR 80 P 8...ORGANIZATION NAME AND ADDRESS 10. PROGRAM ELEMENT PROJECT. TASK AREA a WOPK UNIT NUMOERS Johns - Manville Sales Corper a, t Research & Development Center /0004...P. B. SHEPHERD, R. H. NEISEL JOHNS - MANVILLE SALES CORPORATION RESEARCH & DEVELOPMENT CENTER KEN-CARYL RANCH, DENVER, COLORADO 80217 MARCH 1980 FINAL

  6. 40 CFR 89.417 - Data evaluation for gaseous emissions.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... PROGRAMS (CONTINUED) CONTROL OF EMISSIONS FROM NEW AND IN-USE NONROAD COMPRESSION-IGNITION ENGINES Exhaust Emission Test Procedures § 89.417 Data evaluation for gaseous emissions. For the evaluation of the gaseous...

  7. 40 CFR 89.417 - Data evaluation for gaseous emissions.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... PROGRAMS (CONTINUED) CONTROL OF EMISSIONS FROM NEW AND IN-USE NONROAD COMPRESSION-IGNITION ENGINES Exhaust Emission Test Procedures § 89.417 Data evaluation for gaseous emissions. For the evaluation of the gaseous...

  8. 40 CFR 1054.107 - What is the useful life period for meeting exhaust emission standards?

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... meeting exhaust emission standards? 1054.107 Section 1054.107 Protection of Environment ENVIRONMENTAL... equipment in which the subject engines are installed. (2) Engineering evaluations of field aged engines to ascertain when engine performance deteriorates to the point where usefulness and/or reliability is...

  9. 40 CFR 610.31 - Vehicle tests for fuel economy and exhaust emissions.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 29 2010-07-01 2010-07-01 false Vehicle tests for fuel economy and... (CONTINUED) ENERGY POLICY FUEL ECONOMY RETROFIT DEVICES Test Procedures and Evaluation Criteria Test Requirement Criteria § 610.31 Vehicle tests for fuel economy and exhaust emissions. (a) The tests described...

  10. 40 CFR 610.31 - Vehicle tests for fuel economy and exhaust emissions.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 30 2014-07-01 2014-07-01 false Vehicle tests for fuel economy and... (CONTINUED) ENERGY POLICY FUEL ECONOMY RETROFIT DEVICES Test Procedures and Evaluation Criteria Test Requirement Criteria § 610.31 Vehicle tests for fuel economy and exhaust emissions. (a) The tests described...

  11. 40 CFR 610.31 - Vehicle tests for fuel economy and exhaust emissions.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 31 2013-07-01 2013-07-01 false Vehicle tests for fuel economy and... (CONTINUED) ENERGY POLICY FUEL ECONOMY RETROFIT DEVICES Test Procedures and Evaluation Criteria Test Requirement Criteria § 610.31 Vehicle tests for fuel economy and exhaust emissions. (a) The tests described...

  12. 40 CFR 610.31 - Vehicle tests for fuel economy and exhaust emissions.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 30 2011-07-01 2011-07-01 false Vehicle tests for fuel economy and... (CONTINUED) ENERGY POLICY FUEL ECONOMY RETROFIT DEVICES Test Procedures and Evaluation Criteria Test Requirement Criteria § 610.31 Vehicle tests for fuel economy and exhaust emissions. (a) The tests described...

  13. 40 CFR 610.31 - Vehicle tests for fuel economy and exhaust emissions.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 31 2012-07-01 2012-07-01 false Vehicle tests for fuel economy and... (CONTINUED) ENERGY POLICY FUEL ECONOMY RETROFIT DEVICES Test Procedures and Evaluation Criteria Test Requirement Criteria § 610.31 Vehicle tests for fuel economy and exhaust emissions. (a) The tests described...

  14. 40 CFR 1042.240 - Demonstrating compliance with exhaust emission standards.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... the deterioration expected in emissions over your engines' full useful life. See paragraph (e) of this... additive deterioration factor is the difference between exhaust emissions at the end of the useful life and... factor for a pollutant to be the ratio of exhaust emissions at the end of the useful life to exhaust...

  15. Influence of MTBE addition into gasoline on automotive exhaust emissions

    NASA Astrophysics Data System (ADS)

    Poulopoulos, S.; Philippopoulos, C.

    The effect of methyl-t-butyl ether (MTBE) addition into gasoline on the exhaust emissions from internal combustion engines was studied. A four-cylinder OPEL 1.6 l engine equipped with a hydraulic brake dynamometer was used in all the experiments. Fuels containing 0.0-11.0% MTBE were used in a wide range of engine operations, and the exhaust gases were analyzed for CO, HC (total unburned hydrocarbons, methane, ethylene) and MTBE, before and after their catalytic treatment by a three-way catalytic converter. The addition of MTBE into gasoline resulted in a decrease in CO and HC emissions only at high engine loading. During cold-start up of the engine, MTBE, HC, CO emissions were significant and increased with MTBE addition into fuel. At the catalytic converter outlet MTBE was detected when its concentration in fuels was greater than 8% and only as long as the catalytic converter operates at low temperatures. Methane and ethylene emissions were comparable for all fuels tested at engine outlet, but methane emissions remained almost at the same level while ethylene emissions were significantly decreased by the catalytic converter.

  16. 40 CFR 86.1342-94 - Calculations; exhaust emissions.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ...) Emission Regulations for New Otto-Cycle and Diesel Heavy-Duty Engines; Gaseous and Particulate Exhaust Test... if desired; 16.33 g/ft3-carbon atom (0.5768 kg/m3-carbon atom). (B) For #1 petroleum diesel fuel; 16.42 g/ft3-carbon atom (0.5800 kg/m3-carbon atom). (C) For #2 diesel 16.27 g/ft3-carbon atom (0.5746...

  17. 40 CFR 86.1342-94 - Calculations; exhaust emissions.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ...) Emission Regulations for New Otto-Cycle and Diesel Heavy-Duty Engines; Gaseous and Particulate Exhaust Test... if desired; 16.33 g/ft3-carbon atom (0.5768 kg/m3-carbon atom). (B) For #1 petroleum diesel fuel; 16.42 g/ft3-carbon atom (0.5800 kg/m3-carbon atom). (C) For #2 diesel 16.27 g/ft3-carbon atom (0.5746...

  18. 14 CFR 34.82 - Sampling and analytical procedures for measuring smoke exhaust emissions.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ..., DEPARTMENT OF TRANSPORTATION AIRCRAFT FUEL VENTING AND EXHAUST EMISSION REQUIREMENTS FOR TURBINE ENGINE POWERED AIRPLANES Test Procedures for Engine Smoke Emissions (Aircraft Gas Turbine Engines) §...

  19. 14 CFR 34.82 - Sampling and analytical procedures for measuring smoke exhaust emissions.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ..., DEPARTMENT OF TRANSPORTATION AIRCRAFT FUEL VENTING AND EXHAUST EMISSION REQUIREMENTS FOR TURBINE ENGINE POWERED AIRPLANES Test Procedures for Engine Smoke Emissions (Aircraft Gas Turbine Engines) §...

  20. Methanol fuel vehicle demonstration: Exhaust emission testing. Final report

    SciTech Connect

    Hyde, J.D.

    1993-07-01

    Ford Motor Company converted four stock 1986 Ford Crown Victoria sedans to methanol flexible fuel vehicles (FFVs). During 143,108 operational miles from 1987 to 1990, the FFVs underwent more than 300 dynamometer driving tests to measure exhaust emissions, catalytic activity, fuel economy, acceleration, and driveability with gasoline and methanol blend fuels. Dynamometer driving tests included the Federal Test Procedure (FTP), the Highway Fuel Economy Test, and the New York City Cycle. Exhaust emission measurements included carbon dioxide, carbon monoxide (CO), nitrogen oxides (NO{sub x}), non- oxygenated hydrocarbons, organic material hydrocarbon equivalent (OMHCE), formaldehyde, and methanol. Catalytic activity was based on exhaust emissions data from active and inactive catalysts. OMHCE, CO, and NO{sub x} were usually lower with M85 (85% methanol, 15% gasoline) than with gasoline for both active and inactive catalysts when initial engine and catalyst temperatures were at or near normal operating temperatures. CO was higher with M85 than with gasoline when initial engine and catalyst temperatures were at or near ambient temperature. Formaldehyde and methanol were higher with M85. Active catalyst FTP OMHCE, CO, and NO{sub x} increased as vehicle mileage increased, but increased less with M85 than with gasoline. Energy based fuel economy remained almost constant with changes in fuel composition and vehicle mileage.

  1. U.S. Coast Guard/U.S. Maritime Administration Cooperative Research on Marine Engine Exhaust Emissions. Marine Exhaust Emissions Measurement of the M/V Kings Pointer.

    DTIC Science & Technology

    1996-07-01

    monitoring , and evaluation of the engine exhaust emissions as part of joint U.S. Coast Guard/Maritime Administration cooperative research on controlling air pollution from ships. The U.S. Coast Guard’s interest in emissions testing arises from both its desire to meet all federal and state air quality regulations and the fact that in the future it may be called upon to enforce regulations in the marine environment. The U.S. Maritime Administration’s interest in this and related research is based on its efforts to assure that its vessels and those of the

  2. 40 CFR 1048.240 - How do I demonstrate that my engine family complies with exhaust emission standards?

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... emissions at the end of useful life to exhaust emissions at the low-hour test point. Adjust the official... technology. Also, you may use an additive deterioration factor for exhaust emissions for a particular... represented by the ratio of exhaust emissions at the end of the useful life to exhaust emissions at the low...

  3. 40 CFR 1048.240 - How do I demonstrate that my engine family complies with exhaust emission standards?

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... emissions at the end of useful life to exhaust emissions at the low-hour test point. Adjust the official... technology. Also, you may use an additive deterioration factor for exhaust emissions for a particular... represented by the ratio of exhaust emissions at the end of the useful life to exhaust emissions at the low...

  4. Effects of the biodiesel blend fuel on aldehyde emissions from diesel engine exhaust

    NASA Astrophysics Data System (ADS)

    Peng, Chiung-Yu; Yang, Hsi-Hsien; Lan, Cheng-Hang; Chien, Shu-Mei

    Interest in use of biodiesel fuels derived from vegetable oils or animal fats as alternative fuels for petroleum-based diesels has increased due to biodiesels having similar properties of those of diesels, and characteristics of renewability, biodegradability and potential beneficial effects on exhaust emissions. Generally, exhaust emissions of regulated pollutants are widely studied and the results favor biodiesels on CO, HC and particulate emissions; however, limited and inconsistent data are showed for unregulated pollutants, such as carbonyl compounds, which are also important indicators for evaluating available vehicle fuels. For better understanding biodiesel, this study examines the effects of the biodiesel blend fuel on aldehyde chemical emissions from diesel engine exhausts in comparison with those from the diesel fuel. Test engines (Mitsubishi 4M40-2AT1) with four cylinders, a total displacement of 2.84 L, maximum horsepower of 80.9 kW at 3700 rpm, and maximum torque of 217.6 N m at 2000 rpm, were mounted and operated on a Schenck DyNAS 335 dynamometer. Exhaust emission tests were performed several times for each fuel under the US transient cycle protocol from mileages of 0-80,000 km with an interval of 20,000 km, and two additional measurements were carried out at 40,000 and 80,000 km after maintenance, respectively. Aldehyde samples were collected from diluted exhaust by using a constant volume sampling system. Samples were extracted and analyzed by the HPLC/UV system. Dominant aldehydes of both fuels' exhausts are formaldehyde and acetaldehyde. These compounds together account for over 75% of total aldehyde emissions. Total aldehyde emissions for B20 (20% waste cooking oil biodiesel and 80% diesel) and diesel fuels are in the ranges of 15.4-26.9 mg bhp-h -1 and 21.3-28.6 mg bhp-h -1, respectively. The effects of increasing mileages and maintenance practice on aldehyde emissions are insignificant for both fuels. B20 generates slightly less emission than

  5. OSCEE fan exhaust bulk absorber treatment evaluation

    NASA Technical Reports Server (NTRS)

    Bloomer, H. E.; Samanich, N. E.

    1980-01-01

    The acoustic suppression capability of bulk absorber material designed for use in the fan exhaust duct walls of the quiet clean short haul experiment engine (OCSEE UTW) was evaluated. The acoustic suppression to the original design for the engine fan duct which consisted of phased single degree-of-freedom wall treatment was tested with a splitter and also with the splitter removed. Peak suppression was about as predicted with the bulk absorber configuration, however, the broadband characteristics were not attained. Post test inspection revealed surface oil contamination on the bulk material which could have caused the loss in bandwidth suppression.

  6. Hydrocarbon emissions speciation in diesel and biodiesel exhausts

    NASA Astrophysics Data System (ADS)

    Payri, Francisco; Bermúdez, Vicente R.; Tormos, Bernardo; Linares, Waldemar G.

    Diesel engine emissions are composed of a long list of organic compounds, ranging from C 2 to C 12+, and coming from the hydrocarbons partially oxidized in combustion or produced by pyrolisis. Many of these are considered as ozone precursors in the atmosphere, since they can interact with nitrogen oxides to produce ozone under atmospheric conditions in the presence of sunlight. In addition to problematic ozone production, Brookes, P., and Duncan, M. [1971. Carcinogenic hydrocarbons and human cells in culture. Nature.] and Heywood, J. [1988. Internal Combustion Engine Fundamentals.Mc Graw-Hill, ISBN 0-07-1000499-8.] determined that the polycyclic aromatic hydrocarbons present in exhaust gases are dangerous to human health, being highly carcinogenic. The aim of this study was to identify by means of gas chromatography the amount of each hydrocarbon species present in the exhaust gases of diesel engines operating with different biodiesel blends. The levels of reactive and non-reactive hydrocarbons present in diesel engine exhaust gases powered by different biodiesel fuel blends were also analyzed. Detailed speciation revealed a drastic change in the nature and quantity of semi-volatile compounds when biodiesel fuels are employed, the most affected being the aromatic compounds. Both aromatic and oxygenated aromatic compounds were found in biodiesel exhaust. Finally, the conservation of species for off-side analysis and the possible influence of engine operating conditions on the chemical characterization of the semi-volatile compound phase are discussed. The use of oxygenated fuel blends shows a reduction in the Engine-Out emissions of total hydrocarbons. But the potential of the hydrocarbon emissions is more dependent on the compositions of these hydrocarbons in the Engine-Out, to the quantity; a large percent of hydrocarbons existing in the exhaust, when biodiesel blends are used, are partially burned hydrocarbons, and are interesting as they have the maximum

  7. Diesel Exhaust Emissions Control for Light-Duty Vehicles

    SciTech Connect

    Mital, R.; Li, J.; Huang, S. C.; Stroia, B. J.; Yu, R. C.; Anderson, J.A.; Howden, Kenneth C.

    2003-03-01

    The objective of this paper is to present the results of diesel exhaust aftertreatment testing and analysis done under the FreedomCAR program. Nitrogen Oxides (NOx) adsorber technology was selected based on a previous investigation of various NOx aftertreatment technologies including non-thermal plasma, NOx adsorber and active lean NOx. Particulate Matter (PM) emissions were addressed by developing a catalyzed particulate filter. After various iterations of the catalyst formulation, the aftertreatment components were integrated and optimized for a light duty vehicle application. This compact exhaust aftertreatment system is dual leg and consists of a sulfur trap, NOx adsorbers, and catalyzed particulate filters (CPF). During regeneration, supplementary ARCO ECD low-sulfur diesel fuel is injected upstream of the adsorber and CPF in the exhaust. Steady state and transient emission test results with and without the exhaust aftertreatment system (EAS) are presented. Results of soot filter regeneration by injecting low-sulfur diesel fuel and slip of unregulated emissions, such as NH3, are discussed. Effects of adsorber size and bypass strategy on NOx conversion efficiency and fuel economy penalty are also presented in this paper. The results indicate that if the supplementary fuel injection is optimized, NH3 slip is negligible. During the FTP cycle, injection of low sulfur diesel fuel can create temperature exotherms high enough to regenerate a loaded CPF. With the optimized NOx adsorber regeneration strategies the fuel injection penalty can be reduced by 40 to 50%. Results for various other issues like low temperature light off, reductant optimization, exhaust sulfur management, system integration and design trade-off, are also presented and discussed in this paper. (SAE Paper SAE-2003-01-0041 © 2003 SAE International. This paper is published on this website with permission from SAE International. As a user of this website, you are permitted to view this paper on

  8. Gasoline exhaust emissions induce vascular remodeling pathways involved in atherosclerosis.

    PubMed

    Lund, Amie K; Knuckles, Travis L; Obot Akata, Chrys; Shohet, Ralph; McDonald, Jacob D; Gigliotti, Andrew; Seagrave, Jean Clare; Campen, Matthew J

    2007-02-01

    Epidemiological evidence indicates that environmental air pollutants are positively associated with the development of chronic vascular disease; however, the mechanisms involved have not been fully elucidated. In the present study we examined molecular pathways associated with chronic vascular disease in atherosclerosis-prone apolipoprotein E-deficient (ApoE(-/-)) mice, including markers of vascular remodeling and oxidative stress, in response to exposure to the ubiquitous environmental pollutant, gasoline engine emissions. ApoE(-/-) mice, on a high-fat diet, were exposed by inhalation to either filtered air; 8, 40, or 60 mug/m(3) particulate matter whole exhaust; or filtered exhaust with gases matching the 60-mug/m(3) concentration, for 7 weeks. Aortas and plasma were collected and assayed for changes in histochemical markers, real-time reverse transcriptase-polymerase chain reaction, and indicators of oxidative damage. Inhalational exposure to gasoline engine emissions resulted in increased aortic mRNA expression of matrix metalloproteinase-3 (MMP-3), MMP-7, and MMP-9, tissue inhibitor of metalloproteinases-2, endothelin-1 and heme oxygenase-1 in ApoE(-/-) mice; increased aortic MMP-9 protein levels were confirmed through immunohistochemistry. Elevated reactive oxygen species were also observed in arteries from exposed animals, despite absence of plasma markers. Similar findings were also observed in the aortas of ApoE(-/-) mice exposed to particle-filtered atmosphere, implicating the gaseous components of the whole exhaust in mediating the expression of markers associated with the vasculopathy. These findings demonstrate that exposure to gasoline engine emissions results in the transcriptional upregulation of factors associated with vascular remodeling, as well as increased markers of vascular oxidative stress, which may contribute to the progression of atherosclerosis and reduced stability of vulnerable plaques.

  9. Optimization of gasoline hydrocarbon compositions for reducing exhaust emissions.

    PubMed

    Shen, Yitao; Shuai, Shijin; Wang, Jianxin; Xiao, Jianhua

    2009-01-01

    Effects of hydrocarbon compositions on raw exhaust emissions and combustion processes were studied on an engine test bench. The optimization of gasoline hydrocarbon composition was discussed. As olefins content increased from 10.0% to 25.0% in volume, the combustion duration was shortened by about 2 degree crank angle (degrees CA), and the engine-out THC emission was reduced by about 15%. On the other hand, as aromatics content changed from 35.0% to 45.0%, the engine-out NOx emissions increased by 4%. An increment in olefins content resulted in a slight increase in engine-out CO emission, while the aromatics content had little effect on engine-out total hydrocarbon (THC) and CO emissions. Over the new European driving cycle (NEDC), the THC, NOx and CO emissions of fuel with 25.0% olefins and 35.0% aromatics were about 45%, 21% and 19% lower than those of fuel with 10.0% olefins and 40.0% aromatics, respectively. The optimized gasoline compositions for new engines and new vehicles have low aromatics and high olefins contents.

  10. Assessment for fuel consumption and exhaust emissions of China's vehicles: future trends and policy implications.

    PubMed

    Wu, Yingying; Zhao, Peng; Zhang, Hongwei; Wang, Yuan; Mao, Guozhu

    2012-01-01

    In the recent years, China's auto industry develops rapidly, thus bringing a series of burdens to society and environment. This paper uses Logistic model to simulate the future trend of China's vehicle population and finds that China's auto industry would come into high speed development time during 2020-2050. Moreover, this paper predicts vehicles' fuel consumption and exhaust emissions (CO, HC, NO(x), and PM) and quantificationally evaluates related industry policies. It can be concluded that (1) by 2020, China should develop at least 47 million medium/heavy hybrid cars to prevent the growth of vehicle fuel consumption; (2) China should take the more stringent vehicle emission standard V over 2017-2021 to hold back the growth of exhaust emissions; (3) developing new energy vehicles is the most effective measure to ease the pressure brought by auto industry.

  11. Assessment for Fuel Consumption and Exhaust Emissions of China's Vehicles: Future Trends and Policy Implications

    PubMed Central

    Zhao, Peng; Zhang, Hongwei; Wang, Yuan; Mao, Guozhu

    2012-01-01

    In the recent years, China's auto industry develops rapidly, thus bringing a series of burdens to society and environment. This paper uses Logistic model to simulate the future trend of China's vehicle population and finds that China's auto industry would come into high speed development time during 2020–2050. Moreover, this paper predicts vehicles' fuel consumption and exhaust emissions (CO, HC, NOx, and PM) and quantificationally evaluates related industry policies. It can be concluded that (1) by 2020, China should develop at least 47 million medium/heavy hybrid cars to prevent the growth of vehicle fuel consumption; (2) China should take the more stringent vehicle emission standard V over 2017–2021 to hold back the growth of exhaust emissions; (3) developing new energy vehicles is the most effective measure to ease the pressure brought by auto industry. PMID:23365524

  12. 40 CFR 87.82 - Sampling and analytical procedures for measuring smoke exhaust emissions.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... measuring smoke exhaust emissions. 87.82 Section 87.82 Protection of Environment ENVIRONMENTAL PROTECTION... Test Procedures for Engine Smoke Emissions (Aircraft Gas Turbine Engines) § 87.82 Sampling and analytical procedures for measuring smoke exhaust emissions. The system and procedures for sampling and...

  13. 40 CFR 87.82 - Sampling and analytical procedures for measuring smoke exhaust emissions.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... measuring smoke exhaust emissions. 87.82 Section 87.82 Protection of Environment ENVIRONMENTAL PROTECTION... Test Procedures for Engine Smoke Emissions (Aircraft Gas Turbine Engines) § 87.82 Sampling and analytical procedures for measuring smoke exhaust emissions. The system and procedures for sampling and...

  14. 40 CFR 1066.815 - Exhaust emission test procedures for FTP testing.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... FTP testing. 1066.815 Section 1066.815 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Vehicles § 1066.815 Exhaust emission test procedures for FTP testing. (a) General. The FTP exhaust emission... section and use the corresponding equation in § 1066.820 to calculate FTP composite emissions....

  15. Evaluation of carcinogenic hazard of diesel engine exhaust needs to consider revolutionary changes in diesel technology.

    PubMed

    McClellan, Roger O; Hesterberg, Thomas W; Wall, John C

    2012-07-01

    Diesel engines, a special type of internal combustion engine, use heat of compression, rather than electric spark, to ignite hydrocarbon fuels injected into the combustion chamber. Diesel engines have high thermal efficiency and thus, high fuel efficiency. They are widely used in commerce prompting continuous improvement in diesel engines and fuels. Concern for health effects from exposure to diesel exhaust arose in the mid-1900s and stimulated development of emissions regulations and research to improve the technology and characterize potential health hazards. This included epidemiological, controlled human exposure, laboratory animal and mechanistic studies to evaluate potential hazards of whole diesel exhaust. The International Agency for Research on Cancer (1989) classified whole diesel exhaust as - "probably carcinogenic to humans". This classification stimulated even more stringent regulations for particulate matter that required further technological developments. These included improved engine control, improved fuel injection system, enhanced exhaust cooling, use of ultra low sulfur fuel, wall-flow high-efficiency exhaust particulate filters, exhaust catalysts, and crankcase ventilation filtration. The composition of New Technology Diesel Exhaust (NTDE) is qualitatively different and the concentrations of particulate constituents are more than 90% lower than for Traditional Diesel Exhaust (TDE). We recommend that future reviews of carcinogenic hazards of diesel exhaust evaluate NTDE separately from TDE.

  16. 40 CFR 86.160-00 - Exhaust emission test procedure for SC03 emissions.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ....161-00. (ii) Turn on the solar heating system. (iii) All vehicle test phases of preconditioning, soak... percent relative humidity), a solar heat load intensity of 850 W/m2, and vehicle cooling air flow... all vehicle windows. (4) Connect the emission test sampling system to the vehicle's exhaust tail pipe...

  17. 40 CFR 86.160-00 - Exhaust emission test procedure for SC03 emissions.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ....161-00. (ii) Turn on the solar heating system. (iii) All vehicle test phases of preconditioning, soak... percent relative humidity), a solar heat load intensity of 850 W/m2, and vehicle cooling air flow... all vehicle windows. (4) Connect the emission test sampling system to the vehicle's exhaust tail pipe...

  18. 40 CFR 86.160-00 - Exhaust emission test procedure for SC03 emissions.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ....161-00. (ii) Turn on the solar heating system. (iii) All vehicle test phases of preconditioning, soak... percent relative humidity), a solar heat load intensity of 850 W/m2, and vehicle cooling air flow... all vehicle windows. (4) Connect the emission test sampling system to the vehicle's exhaust tail pipe...

  19. 40 CFR 86.160-00 - Exhaust emission test procedure for SC03 emissions.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ....161-00. (ii) Turn on the solar heating system. (iii) All vehicle test phases of preconditioning, soak... percent relative humidity), a solar heat load intensity of 850 W/m2, and vehicle cooling air flow... all vehicle windows. (4) Connect the emission test sampling system to the vehicle's exhaust tail pipe...

  20. Exhaust Gas Emissions from a Rotating Detonation-wave Engine

    NASA Astrophysics Data System (ADS)

    Kailasanath, Kazhikathra; Schwer, Douglas

    2015-11-01

    Rotating detonation-wave engines (RDE) are a form of continuous detonation-wave engines. They potentially provide further gains in performance than an intermittent or pulsed detonation-wave engine (PDE). The overall flow field in an idealized RDE, primarily consisting of two concentric cylinders, has been discussed in previous meetings. Because of the high pressures involved and the lack of adequate reaction mechanisms for this regime, previous simulations have typically used simplified chemistry models. However, understanding the exhaust species concentrations in propulsion devices is important for both performance considerations as well as estimating pollutant emissions. Progress towards addressing this need will be discussed in this talk. In this approach, an induction parameter model is used for simulating the detonation but a more detailed finite-chemistry model including NOx chemistry is used in the expansion flow region, where the pressures are lower and the uncertainties in the chemistry model are greatly reduced. Results show that overall radical concentrations in the exhaust flow are substantially lower than from earlier predictions with simplified models. The performance of a baseline hydrogen/air RDE increased from 4940 s to 5000 s with the expansion flow chemistry, due to recombination of radicals and more production of H2O, resulting in additional heat release. Work sponsored by the Office of Naval Research.

  1. GIS-based modal model of automobile exhaust emissions. Final report, January 1997--May 1998

    SciTech Connect

    Bachman, W.H.

    1998-08-01

    The report presents progress toward the development of a computer tool called MEASURE, the Mobile Emission Assessment System for Urban and Regional Evaluation. The tool works toward a goal of providing researchers and planners with a way to assess new mobile emission mitigation strategies. The model is based on a geographic information system (GIS) and uses modal operation (acceleration, deceleration, cruise, and idle). Estimates of spatially resolved fleet composition and activity are combined with situation-specific emission rates to predict engine start and running exhaust emissions. The estimates are provided at user-defined spatial scales. A demonstration of model operation is provided using a 100 sq km study area in Atlanta, Georgia. Future mobile emissions modeling research needs are developed from an analysis of the sources of model error.

  2. A GIS-BASED MODAL MODEL OF AUTOMOBILE EXHAUST EMISSIONS

    EPA Science Inventory

    The report presents progress toward the development of a computer tool called MEASURE, the Mobile Emission Assessment System for Urban and Regional Evaluation. The tool works toward a goal of providing researchers and planners with a way to assess new mobile emission mitigation s...

  3. Motor vehicle exhaust emissions and control in Finland

    SciTech Connect

    Laurikko, J.

    1989-01-01

    This paper outlines the status and trends of atmospheric pollution in Finland caused by motor vehicles and evaluates the effect of the current regulatory policy. Details of new emission regulations for passenger cars and heavy duty vehicles are given. Research activities and items of particular concern like the effect of low ambient temperature on emissions are also discussed.

  4. A GIS-BASED MODAL MODEL OF AUTOMOBILE EXHAUST EMISSIONS

    EPA Science Inventory

    The report presents progress toward the development of a computer tool called MEASURE, the Mobile Emission Assessment System for Urban and Regional Evaluation. The tool works toward a goal of providing researchers and planners with a way to assess new mobile emission mitigation s...

  5. Evaluation of a disposable diesel exhaust filter for permissible mining machines

    SciTech Connect

    Ambs, J.L.; Cantrell, B.K.; Watts, W.F.; Olson, K.S.

    1994-01-01

    The US Bureau of Mines (USBM) Diesel Research Program emphasizes the development and evaluation of emission control devices to reduce exposure of miners to diesel exhaust pollutants. Studies by the USBM have shown that diesel exhaust aerosol (DEA) contributes a substantial portion of the respirable aerosol in underground coal mines using diesel equipment not equipped with emission controls. The USBM and the Donaldson Co., Inc., Minneapolis, MN, have developed a low-temperature, disposable diesel exhaust filter (DDEF) for use on permissible diesel haulage vehicles equipped with waterbath exhaust conditioners. These were evaluated in three underground mines to determine their effectiveness in reducing DEA concentrations. The DDEF reduced DEA concentrations from 70 to 90% at these mines. The usable life of the filter ranged from 10 to 32 h, depending on factors that affect DEA output, such as mine altitude, engine type, and duty-cycle. Cost per filter is approximately $40.

  6. Evaluation of a disposable diesel exhaust filter for permissible mining machines. Report of investigations/1994

    SciTech Connect

    Ambs, J.L.; Cantrell, B.K.; Watts, W.F.; Olson, K.S.

    1994-01-01

    The U.S. Bureau of Mines (USBM) Diesel Research Program emphasizes the development and evaluation of emission control devices to reduce exposure of miners to diesel exhaust pollutants. Studies by the USBM have shown that diesel exhaust aerosol (DEA) contributes a substantial portion of the respirable aerosol in underground coal mining using diesel equipment not equipped with emission controls. The USBM and the Donaldson Co., Inc., Minneapolis, MN, have developed a low-temperature, disposable diesel exhaust filter (DDEF) for use on permissible diesel haulage vehicles equipped with waterban exhaust conditioners. These were evaluated in three underground mines to determine their effectiveness in reducing DEA concentrations. The DDEF reduced DEA concentrations from 70 to 90 pct at these mines. The usable life of the filter ranged from 10 to 32 h, depending on factors that affect DEA output, such as mine altitude, engine type, and duty-cycle. Cost per filter is approximately $40.

  7. Nitrogen dioxide in exhaust emissions from motor vehicles

    NASA Astrophysics Data System (ADS)

    Lenner, Magnus

    NO 2/NO x (v/v) fractions and NO 2 exhaust emission rates were determined for diesel- and gasoline-powered passenger cars and a diesel truck, at several conditions of constant engine load and speed. Vehicles with various kinds of emission control equipment were investigated. Also, integrations of NO 2/NO x percentages during Federal Test Procedure driving cycles were made for six types of passenger car. High (> 30 %) NO 2 fractions were measured for gasoline cars with air injection, and for diesel vehicles. A gasoline car with a 3-way catalyst had low NO x totals with small (< 1 %) NO 2 fractions. A passenger diesel with particle trap yielded surprisingly small (0-2%) NO 2 fractions at moderate speeds. The results have implications for NO 2 concentration in the atmosphere of northern cities during wintertime inversions, in view of the increasing use of air injection systems for passenger cars to meet legal restrictions on vehicle emissions of hydrocarbons and CO.

  8. Assessment of exhaust emissions from carbon nanotube production and particle collection by sampling filters.

    PubMed

    Tsai, Candace Su-Jung; Hofmann, Mario; Hallock, Marilyn; Ellenbecker, Michael; Kong, Jing

    2015-11-01

    This study performed a workplace evaluation of emission control using available air sampling filters and characterized the emitted particles captured in filters. Characterized particles were contained in the exhaust gas released from carbon nanotube (CNT) synthesis using chemical vapor deposition (CVD). Emitted nanoparticles were collected on grids to be analyzed using transmission electron microscopy (TEM). CNT clusters in the exhaust gas were collected on filters for investigation. Three types of filters, including Nalgene surfactant-free cellulose acetate (SFCA), Pall A/E glass fiber, and Whatman QMA quartz filters, were evaluated as emission control measures, and particles deposited in the filters were characterized using scanning transmission electron microscopy (STEM) to further understand the nature of particles emitted from this CNT production. STEM analysis for collected particles on filters found that particles deposited on filter fibers had a similar morphology on all three filters, that is, hydrophobic agglomerates forming circular beaded clusters on hydrophilic filter fibers on the collecting side of the filter. CNT agglomerates were found trapped underneath the filter surface. The particle agglomerates consisted mostly of elemental carbon regardless of the shapes. Most particles were trapped in filters and no particles were found in the exhaust downstream from A/E and quartz filters, while a few nanometer-sized and submicrometer-sized individual particles and filament agglomerates were found downstream from the SFCA filter. The number concentration of particles with diameters from 5 nm to 20 µm was measured while collecting particles on grids at the exhaust piping. Total number concentration was reduced from an average of 88,500 to 700 particle/cm(3) for the lowest found for all filters used. Overall, the quartz filter showed the most consistent and highest particle reduction control, and exhaust particles containing nanotubes were successfully

  9. Effect of gasoline/methanol blends on motorcycle emissions: Exhaust and evaporative emissions

    NASA Astrophysics Data System (ADS)

    Li, Lan; Ge, Yunshan; Wang, Mingda; Li, Jiaqiang; Peng, Zihang; Song, Yanan; Zhang, Liwei

    2015-02-01

    The emission characteristics of motorcycles using gasoline and M15 (consisting of 85% gasoline and 15% methanol by volume) were investigated in this article. Exhaust and evaporative emissions, including regulated and unregulated emissions, of three motorcycles were investigated on the chassis dynamometer over the Urban Driving Cycle (UDC) and in the Sealed Housing for Evaporative Determination (SHED), respectively. The regulated emissions were detected by an exhaust gas analyzer directly. The unregulated emissions, including carbonyls, volatile organic compounds (VOCs) and methanol, were sampled through battery-operated air pumps using tubes coated with 2,4-dintrophenylhydrazine (DNPH), Tenax TA and silica gel, respectively. The experimental results showed that, for exhaust emission, compared with those from gasoline fueled motorcycles, the concentration of total hydrocarbons (THC) and CO from motorcycles fueled with M15 decreased by 11%-34.5% and 63%-84% respectively, while the concentration of NOx increased by 76.9%-107.7%. Compared with those from gasoline fueled motorcycles, BTEX from motorcycles fueled with M15 decreased by 16%-60% while formaldehyde increased by 16.4%-52.5%. For evaporative emission, diurnal losses were more than hot soak losses and turned out to be dominated in evaporative emissions. In addition, compared with gasoline fueling motorcycles, the evaporative emissions of THC, carbonyls and VOCs from motorcycles fueled with M15 increased by 11.7%-37%, 38%-45% and 16%-42%, respectively. It should be noted that the growth rate of methanol was as high as 297%-1429%. It is important to reduce the evaporative emissions of methanol fueling motorcycles.

  10. 40 CFR 1037.102 - Exhaust emission standards for NOX, HC, PM, and CO.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ..., PM, and CO. 1037.102 Section 1037.102 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... and Related Requirements § 1037.102 Exhaust emission standards for NOX, HC, PM, and CO. See 40 CFR part 86 for the exhaust emission standards for NOX, HC, PM, and CO that apply for heavy-duty vehicles....

  11. 40 CFR 1037.102 - Exhaust emission standards for NOX, HC, PM, and CO.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ..., PM, and CO. 1037.102 Section 1037.102 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... and Related Requirements § 1037.102 Exhaust emission standards for NOX, HC, PM, and CO. See 40 CFR part 86 for the exhaust emission standards for NOX, HC, PM, and CO that apply for heavy-duty vehicles....

  12. 40 CFR 1037.102 - Exhaust emission standards for NOX, HC, PM, and CO.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ..., PM, and CO. 1037.102 Section 1037.102 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... and Related Requirements § 1037.102 Exhaust emission standards for NOX, HC, PM, and CO. See 40 CFR part 86 for the exhaust emission standards for NOX, HC, PM, and CO that apply for heavy-duty vehicles....

  13. 78 FR 34375 - Proposed Information Collection Request; Comment Request; Exhaust Emissions of Light-Duty...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-06-07

    ... AGENCY Proposed Information Collection Request; Comment Request; Exhaust Emissions of Light-Duty Vehicles... request (ICR), ``Exhaust Emissions of Light-duty Vehicles in Metropolitan Detroit'' (EPA ICR No. 2363.02... CONTACT: James Warila, Assessment and Standards Division, Office of Transportation and Air Quality, (AADTC...

  14. 40 CFR 1037.105 - Exhaust emission standards for CO2 for vocational vehicles.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 34 2013-07-01 2013-07-01 false Exhaust emission standards for CO2 for... and Related Requirements § 1037.105 Exhaust emission standards for CO2 for vocational vehicles. (a... engines certified under § 1037.150(m). (b) The CO2 standards of this section are given in Table 1 to...

  15. 40 CFR 1037.105 - Exhaust emission standards for CO2 for vocational vehicles.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 33 2014-07-01 2014-07-01 false Exhaust emission standards for CO2 for... and Related Requirements § 1037.105 Exhaust emission standards for CO2 for vocational vehicles. (a... engines certified under § 1037.150(m). (b) The CO2 standards of this section are given in Table 1 to...

  16. 40 CFR 1037.105 - Exhaust emission standards for CO2 for vocational vehicles.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 34 2012-07-01 2012-07-01 false Exhaust emission standards for CO2 for... and Related Requirements § 1037.105 Exhaust emission standards for CO2 for vocational vehicles. (a... engines certified under § 1037.150(m). (b) The CO2 standards of this section are given in Table 1 to...

  17. 40 CFR 1066.610 - Mass-based and molar-based exhaust emission calculations.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 34 2012-07-01 2012-07-01 false Mass-based and molar-based exhaust... (CONTINUED) AIR POLLUTION CONTROLS VEHICLE-TESTING PROCEDURES Calculations § 1066.610 Mass-based and molar-based exhaust emission calculations. (a) Calculate your total mass of emissions over a test cycle as...

  18. 40 CFR 1066.610 - Mass-based and molar-based exhaust emission calculations.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 34 2013-07-01 2013-07-01 false Mass-based and molar-based exhaust... (CONTINUED) AIR POLLUTION CONTROLS VEHICLE-TESTING PROCEDURES Calculations § 1066.610 Mass-based and molar-based exhaust emission calculations. (a) Calculate your total mass of emissions over a test cycle as...

  19. 75 FR 67634 - Compliance With Interstate Motor Carrier Noise Emission Standards: Exhaust Systems

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-11-03

    ... Carrier Noise Emission Standards: Exhaust Systems AGENCY: Federal Motor Carrier Safety Administration, DOT... Motor Carrier Noise Emission Standards: Exhaust Systems,'' published on September 20, 2010, in the... to be noise dissipative devices. DATES: This rule is effective November 19, 2010. ADDRESSES: The...

  20. 40 CFR 87.64 - Sampling and analytical procedures for measuring gaseous exhaust emissions.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 20 2011-07-01 2011-07-01 false Sampling and analytical procedures for measuring gaseous exhaust emissions. 87.64 Section 87.64 Protection of Environment ENVIRONMENTAL PROTECTION....64 Sampling and analytical procedures for measuring gaseous exhaust emissions. (a) The system...

  1. 14 CFR 34.64 - Sampling and analytical procedures for measuring gaseous exhaust emissions.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 14 Aeronautics and Space 1 2012-01-01 2012-01-01 false Sampling and analytical procedures for measuring gaseous exhaust emissions. 34.64 Section 34.64 Aeronautics and Space FEDERAL AVIATION... Turbine Engines) § 34.64 Sampling and analytical procedures for measuring gaseous exhaust emissions. The...

  2. 14 CFR 34.82 - Sampling and analytical procedures for measuring smoke exhaust emissions.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 14 Aeronautics and Space 1 2012-01-01 2012-01-01 false Sampling and analytical procedures for measuring smoke exhaust emissions. 34.82 Section 34.82 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION... Sampling and analytical procedures for measuring smoke exhaust emissions. The system and procedures for...

  3. 40 CFR 1045.240 - How do I demonstrate that my engine family complies with exhaust emission standards?

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... deterioration factors that represent the expected deterioration in emissions over your engines' full useful life... deterioration factor for exhaust emissions. For engines that do not use aftertreatment technology, use an... between exhaust emissions at the end of useful life and exhaust emissions at the low-hour test point...

  4. 40 CFR 1039.240 - How do I demonstrate that my engine family complies with exhaust emission standards?

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... deterioration factors that represent the deterioration expected in emissions over your engines' full useful life... additive deterioration factor is the difference between exhaust emissions at the end of the useful life and... pollutant to be the ratio of exhaust emissions at the end of the useful life to exhaust emissions at the low...

  5. 40 CFR 1045.240 - How do I demonstrate that my engine family complies with exhaust emission standards?

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... deterioration factors that represent the expected deterioration in emissions over your engines' full useful life... deterioration factor for exhaust emissions. For engines that do not use aftertreatment technology, use an... between exhaust emissions at the end of useful life and exhaust emissions at the low-hour test point...

  6. 40 CFR 600.114-12 - Vehicle-specific 5-cycle fuel economy and carbon-related exhaust emission calculations.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... Vehicle-specific 5-cycle fuel economy and carbon-related exhaust emission calculations. Paragraphs (a.... Paragraphs (d) through (f) of this section are used to calculate 5-cycle carbon-related exhaust emission... emissions and carbon-related exhaust emissions. For each vehicle tested, determine the 5-cycle city...

  7. 40 CFR 600.114-12 - Vehicle-specific 5-cycle fuel economy and carbon-related exhaust emission calculations.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... Vehicle-specific 5-cycle fuel economy and carbon-related exhaust emission calculations. Paragraphs (a.... Paragraphs (d) through (f) of this section are used to calculate 5-cycle carbon-related exhaust emission... emissions and carbon-related exhaust emissions. For each vehicle tested, determine the 5-cycle city...

  8. Development of Diesel Exhaust Aftertreatment System for Tier II Emissions

    SciTech Connect

    Yu, R. C.; Cole, A. S., Stroia, B. J.; Huang, S. C.; Howden, Kenneth C.; Chalk, Steven

    2002-06-01

    system design and analysis, critical lab/engine experiments, and ranking then selection of NOX control technologies against reliability, up-front cost, fuel economy, service interval/serviceability, and size/weight. The results of the investigations indicate that the best NOX control approach for LDV and LDT applications is a NOX adsorber system. A greater than 83% NOX reduction efficiency is required to achieve 0.07g/mile NOX Tier II vehicle-out emissions. Both active lean NOX and PACR technology are currently not capable of achieving the high conversion efficiency required for Tier II, Bin 5 emissions standards. In this paper, the NOX technology assessment and selection is first reviewed and discussed. Development of the selected NOX technology (NOX adsorber) and PM control are then discussed in more detail. Discussion includes exhaust sulfur management, further adsorber formulation development, reductant screening, diesel particulate filter development & active regeneration, and preliminary test results on the selected integrated SOX trap, NOX adsorber, and diesel particulate filter system over an FTP-75 emissions cycle, and its impact on fuel economy. Finally, the direction of future work for continued advanced aftertreatment technology development is discussed. (SAE Paper SAE-2002-01-1867 © 2002 SAE International. This paper is published on this website with permission from SAE International. As a user of this website, you are permitted to view this paper on-line, download this pdf file and print one copy of this paper at no cost for your use only. The downloaded pdf file and printout of this SAE paper may not be copied, distributed or forwarded to others or for the use of others.)

  9. 4-Nitrophenol, 1-nitropyrene, and 9-nitroanthracene emissions in exhaust particles from diesel vehicles with different exhaust gas treatments

    NASA Astrophysics Data System (ADS)

    Inomata, Satoshi; Fushimi, Akihiro; Sato, Kei; Fujitani, Yuji; Yamada, Hiroyuki

    2015-06-01

    The dependence of nitro-organic compound emissions in automotive exhaust particles on the type of aftertreatment used was investigated. Three diesel vehicles with different aftertreatment systems (an oxidation catalyst, vehicle-DOC; a particulate matter and NOx reduction system, vehicle-DPNR; and a urea-based selective catalytic reduction system, vehicle-SCR) and a gasoline car with a three-way catalyst were tested. Nitro-polycyclic aromatic hydrocarbons (nitro-PAHs) and nitrophenols in the particles emitted were analyzed by thermal desorption gas chromatography/mass spectrometry and liquid chromatography/mass spectrometry. The secondary production of nitro-organic compounds on the filters used to collect particles and the adsorption of gaseous nitro-organic compounds by the filters were evaluated. Emissions of 1-nitropyrene, 9-nitroanthracene, and 4-nitrophenol in the diesel exhaust particles were then quantified. The NOx reduction process in vehicle-DPNR appeared to remove nitro-hydrocarbons efficiently but not to remove nitro-oxygenated hydrocarbons efficiently. The nitro-PAH emission factors were lower for vehicle-DOC when it was not fitted with a catalyst than when it was fitted with a catalyst. The 4-nitrophenol emission factors were also lower for vehicle-DOC with a catalyst than vehicle-DOC without a catalyst, suggesting that the oxidation catalyst was a source of both nitro-PAHs and 4-nitrophenol. The time-resolved aerosol mass spectrometry data suggested that nitro-organic compounds are mainly produced when an engine is working under load. The presence of 4-nitrophenol in the particles was not confirmed statistically because of interference from gaseous 4-nitrophenol. Systematic errors in the estimated amounts of gaseous 1-nitropyrene and 9-nitroanthracene adsorbed onto the filters and the estimated amounts of volatile nitro-organic compounds that evaporated during sampling and during post-sampling conditioning could not be excluded. An analytical method

  10. US Coast Guard/US Maritime Administration Cooperative Research on marine engine exhaust emissions. Marine exhaust emissions measurement of the M/V Kings Pointer. Final report

    SciTech Connect

    Allen, S.J.; Bentz, A.P.

    1996-07-01

    This report presents the results of emissions testing conducted on board the M/V KINGS POINTER in May 1995. The objective of this testing was to conduct baseline instrumentation, monitoring, and evaluation of the engine exhaust emissions as part of joint U.S. Coast Guard/Maritime Administration cooperative research on controlling air pollution from ships. The U.S. Coast Guard`s interest in emissions testing arises from both its desire to meet all federal and state air quality regulations and the fact that in the future it may be called upon to enforce regulations in the marine environment. The U.S. Maritime Administration`s interest in this and related research is based on its efforts to assure that its vessels and those of the privately-owned U.S. Flag Merchant Marine can comply with future air pollution control requirements. Underway tests were conducted of the 224-foot M/V KINGS POINTER in which two of its four diesel-electric generators were sampled for NO, NO2, CO, and SO2 in the exhaust. Additional data on fuel flow and power output were collected at five speeds over the full range of vessel operating ranges. NOx values were calculated and compared with standards proposed by the Environmental Protection Agency (EPA) and the International Maritime Organization (IMO). Results showed that average NOx values were 9.4 g/kWh which is slightly below the 10.9 g/kWh upper limit or cap that is being proposed by the IMO for a diesel engine with a rated speed of 1200 RPM. Additional conclusions and recommendations on the technique of portable emissions monitoring instrumentation are made.

  11. Exhaust emissions reduction from diesel engine using combined Annona-Eucalyptus oil blends and antioxidant additive

    NASA Astrophysics Data System (ADS)

    Senthil, R.; Silambarasan, R.; Pranesh, G.

    2017-03-01

    The limited resources, rising petroleum prices and depletion of fossil fuel have now become a matter of great concern. Hence, there is an urgent need for researchers to find some alternate fuels which are capable of substituting partly or wholly the higher demanded conventional diesel fuel. Lot of research work has been conducted on diesel engine using biodiesel and its blends with diesel as an alternate fuel. Very few works have been done with combination of biodiesel-Eucalypts oil without neat diesel and this leads to lots of scope in this area. The aim of the present study is to analyze the performance and emission characteristics of a single cylinder, direct injection, compression ignition engine using eucalyptus oil-biodiesel as fuel. The presence of eucalyptus oil in the blend reduces the viscosity and improves the volatility of the blends. The methyl ester of Annona oil is blended with eucalypts oil in 10, 20, 30, 40 and 50 %. The performance and emission characteristics are evaluated by operating the engine at different loads. The performance characteristics such as brake thermal efficiency, brake specific fuel consumption and exhaust gas temperature are evaluated. The emission constituents measured are Carbon monoxide (CO), unburned hydrocarbons (HC), Oxides of nitrogen (NOx) and Smoke. It is found that A50-Eu50 (50 Annona + 50 % Eucalyptus oil) blend showed better performance and reduction in exhaust emissions. But, it showed a very marginal increase in NOx emission when compared to that of diesel. Therefore, in order to reduce the NOx emission, antioxidant additive (A-tocopherol acetate) is mixed with Annona-Eucalyptus oil blends in various proportions by which NOx emission is reduced. Hence, A50-Eu50 blend can be used as an alternate fuel for diesel engine without any modifications.

  12. Exhaust emissions reduction from diesel engine using combined Annona-Eucalyptus oil blends and antioxidant additive

    NASA Astrophysics Data System (ADS)

    Senthil, R.; Silambarasan, R.; Pranesh, G.

    2016-07-01

    The limited resources, rising petroleum prices and depletion of fossil fuel have now become a matter of great concern. Hence, there is an urgent need for researchers to find some alternate fuels which are capable of substituting partly or wholly the higher demanded conventional diesel fuel. Lot of research work has been conducted on diesel engine using biodiesel and its blends with diesel as an alternate fuel. Very few works have been done with combination of biodiesel-Eucalypts oil without neat diesel and this leads to lots of scope in this area. The aim of the present study is to analyze the performance and emission characteristics of a single cylinder, direct injection, compression ignition engine using eucalyptus oil-biodiesel as fuel. The presence of eucalyptus oil in the blend reduces the viscosity and improves the volatility of the blends. The methyl ester of Annona oil is blended with eucalypts oil in 10, 20, 30, 40 and 50 %. The performance and emission characteristics are evaluated by operating the engine at different loads. The performance characteristics such as brake thermal efficiency, brake specific fuel consumption and exhaust gas temperature are evaluated. The emission constituents measured are Carbon monoxide (CO), unburned hydrocarbons (HC), Oxides of nitrogen (NOx) and Smoke. It is found that A50-Eu50 (50 Annona + 50 % Eucalyptus oil) blend showed better performance and reduction in exhaust emissions. But, it showed a very marginal increase in NOx emission when compared to that of diesel. Therefore, in order to reduce the NOx emission, antioxidant additive (A-tocopherol acetate) is mixed with Annona-Eucalyptus oil blends in various proportions by which NOx emission is reduced. Hence, A50-Eu50 blend can be used as an alternate fuel for diesel engine without any modifications.

  13. Emission factor of exhaust gas constituents during the pyrolysis of zinc chloride immersed biosolid.

    PubMed

    Chiang, Hung-Lung; Lin, Kuo-Hsiung; Chiu, Hua-Hsien

    2013-08-01

    Pyrolysis enables ZnCl2 immersed biosolid to be reused, but some hazardous air pollutants are emitted during this process. Physical characteristics of biosolid adsorbents were investigated in this work. In addition, the constituents of pyrolytic exhaust were determined to evaluate the exhaust characteristics. Results indicated that the pyrolytic temperature was higher than 500 °C, the specific surface area was >900 m(2)/g, and the total pore volume was as much as 0.8 cm(3)/g at 600 °C. For non-ZnCl2 immersed biosolid pyrolytic exhaust, VOC emission factors increased from 0.677 to 3.170 mg-VOCs/g-biosolid with the pyrolytic temperature increase from 400 to 700 °C, and chlorinated VOCs and oxygenated VOCs were the dominant fraction of VOC groups. VOC emission factors increased about three to seven times, ranging from 1.813 to 21.448 mg/g for pyrolytic temperatures at 400-700 °C, corresponding to the mass ratio of ZnCl2 and biosolid ranging from 0.25-2.5.

  14. Exhaust emissions from light- and heavy-duty vehicles: chemical composition, impact of exhaust after treatment, and fuel parameters.

    PubMed Central

    Westerholm, R; Egebäck, K E

    1994-01-01

    This paper presents results from the characterization of vehicle exhaust that were obtained primarily within the Swedish Urban Air Project, "Tätortsprojektet." Exhaust emissions from both gasoline- and diesel-fueled vehicles have been investigated with respect to regulated pollutants (carbon monoxide [CO], hydrocarbon [HC], nitrogen oxides [NOx], and particulate), unregulated pollutants, and in bioassay tests (Ames test, TCDD receptor affinity tests). Unregulated pollutants present in both the particle- and the semi-volatile phases were characterized. Special interest was focused on the impact of fuel composition on heavy-duty diesel vehicle emissions. It was confirmed that there exists a quantifiable relationship between diesel-fuel variables of the fuel blends, the chemical composition of the emissions, and their biological effects. According to the results from the multivariate analysis, the most important fuel parameters are: polycyclic aromatic hydrocarbons (PAH) content, 90% distillation point, final boiling point, specific heat, aromatic content, density, and sulfur content. PMID:7529699

  15. Emissions and fuel economy effects of vehicle exhaust emission control device (revision). Technical report

    SciTech Connect

    Johnson, H.

    1998-10-01

    This report describes testing by EPA of the Vehicle Exhaust Emission Control Device (VEECD) retrofit device under Section 32918 of Title 49 U.S.C. Retrofit Devices (RD). The VEECD is described by the developer in the international patent application as an embodiment of air bleed principle. It is intended to be retrofitted to vehicles produced without any, or with earlier-technology emission control systems. The developer claims (RD Application Appendix A) that the valve significantly reduces CO and HC emissions without substantially increasing CO{sub 2} or NOx emissions. Incidental city fuel economy enhancement was also claimed. Non-FTP test data obtained for 1986/87 European vehicles from two laboratories in the UK was submitted. This data (Appendix B) was analyzed using the t-test for the difference of constant speed data (30/60/85MPH) at 95% confidence level.

  16. 40 CFR 600.114-08 - Vehicle-specific 5-cycle fuel economy and carbon-related exhaust emission calculations.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... Vehicle-specific 5-cycle fuel economy and carbon-related exhaust emission calculations. Paragraphs (a.... Paragraphs (d) through (f) of this section are used to calculate 5-cycle carbon-related exhaust emissions..., determine the 5-cycle city carbon-related exhaust emissions using the following equation: (1) CityCREE =...

  17. 40 CFR 600.114-08 - Vehicle-specific 5-cycle fuel economy and carbon-related exhaust emission calculations.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... Vehicle-specific 5-cycle fuel economy and carbon-related exhaust emission calculations. Paragraphs (a.... Paragraphs (d) through (f) of this section are used to calculate 5-cycle carbon-related exhaust emissions..., determine the 5-cycle city carbon-related exhaust emissions using the following equation: (1) CityCREE =...

  18. COMPARATIVE STUDY ON EXHAUST EMISSIONS FROM DIESEL- AND CNG-POWERED URBAN BUSES

    SciTech Connect

    COROLLER, P; PLASSAT, G

    2003-08-24

    Couple years ago, ADEME engaged programs dedicated to the urban buses exhaust emissions studies. The measures associated with the reduction of atmospheric and noise pollution has particular importance in the sector of urban buses. In many cases, they illustrate the city's environmental image and contribute to reinforcing the attractiveness of public transport. France's fleet in service, presently put at about 14,000 units, consumes about 2 per cent of the total energy of city transport. It causes about 2 per cent of the HC emissions and from 4 to 6 per cent of the NOx emissions and particles. These vehicles typically have a long life span (about 15 years) and are relatively expensive to buy, about 150.000 euros per unit. Several technical solutions were evaluated to quantify, on a real condition cycle for buses, on one hand pollutants emissions, fuel consumption and on the other hand reliability, cost in real existing fleet. This paper presents main preliminary results on urban buses exhaust emission on two different cases: - existing Diesel buses, with fuel modifications (Diesel with low sulphur content), Diesel with water emulsion and bio-Diesel (30% oil ester in standard Diesel fuel); renovating CNG powered Euro II buses fleet, over representative driving cycles, set up by ADEME and partners. On these cycles, pollutants (regulated and unregulated) were measured as well as fuel consumption, at the beginning of a program and one year after to quantify reliability and increase/decrease of pollutants emissions. At the same time, some after-treatment technologies were tested under real conditions and several vehicles. Information such as fuel consumption, lubricant analysis, problem on the technology were following during a one year program. On the overall level, it is the combination of various action, pollution-reduction and renewal that will make it possible to meet the technological challenge of reducing emissions and fuel consumption by urban bus networks.

  19. Exposure to diesel exhaust emissions on board locomotives.

    PubMed

    Seshagiri, Baily

    2003-01-01

    Measurements of diesel exhaust emissions (DEEs) were taken in the cabs of leading and trailing locomotives on 48 runs, under winter and summer conditions, on 9 different routes. The cab windows were kept open during the summer runs and closed during the winter runs. The average measurement duration was 9.5 hours. There was virtually no exposure to DEEs in the lead locomotives during winter or summer and very little in the trailing locomotives during winter. The average elemental carbon (EC) concentration in the trailing units of the summer trials was greater than or equal to the proposed American Conference of Governmental Industrial Hygienists' threshold limit value/time-weighted average of 20 microg/m(3) on 26% of the runs, and was greater than or equal to 10 microg/m(3) on 63%. The concentrations of the gaseous components (nitric oxide, nitrogen dioxide, and carbon monoxide) were from 10 to 20 times below their respective threshold limit values. Mean EC concentration was 2.9 microg/m(3) (detection limit 2 microg/m(3)) during the winter runs and 17.1 microg/m(3) during summer. DEEs appeared to be fairly uniformly distributed in the trailing cabs. Configuration of the locomotives had a major impact on EC concentration, with the mean concentration being nearly three times higher in the forward-backward mode than in the forward-forward mode. Descriptive statistics such as means, medians, standard deviations, and so forth, are provided. Various types of statistical comparisons are reported. Recommendations for controlling exposure are made.

  20. 40 CFR 87.82 - Sampling and analytical procedures for measuring smoke exhaust emissions.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 21 2012-07-01 2012-07-01 false Sampling and analytical procedures for measuring smoke exhaust emissions. 87.82 Section 87.82 Protection of Environment ENVIRONMENTAL PROTECTION... (Aircraft Gas Turbine Engines) § 87.82 Sampling and analytical procedures for measuring smoke exhaust...

  1. Bioethanol-gasoline fuel blends: exhaust emissions and morphological characterization of particulate from a moped engine.

    PubMed

    Seggiani, Maurizia; Prati, M Vittoria; Costagliola, M Antonietta; Puccini, Monica; Vitolo, Sandra

    2012-08-01

    This study was aimed at evaluating the effects of gasoline-ethanol blends on the exhaust emissions in a catalyst-equipped four-stroke moped engine. The ethanol was blended with unleaded gasoline in at percentages (10, 15, and 20% v/v). The regulated pollutants and the particulate matter emissions were evaluated over the European ECE R47 driving cycle on the chassis dynamometer bench. Particulate matter was characterized in terms of total mass collected on filters and total number ofparticles in the range 7 nm-10 microm measured by electrical low-pressure impactor (ELPI). In addition, particle-phase polycyclic aromatic hydrocarbons (PAHs) emissions were evaluated to assess the health impact of the emitted particulate. Finally, an accurate morphological analysis was performed on the particulate by high-resolution transmission electron microscope (TEM) equipped with a digital image-processing/data-acquisition system. In general, CO emission reductions of 60-70% were obtained with 15 and 20% v/v ethanol blends, while the ethanol use did not reduce hydrocarbon (HC) and NOx emissions. No evident effect of ethanol on the particulate mass emissions and associated PAHs emissions was observed. Twenty-one PAHs were quantified in the particulate phase with emissions ranging from 26 to 35 microg/km and benzo[a]pyrene equivalent (BaPeq) emission factors from 2.2 to 4.1 microg/km. Both particulate matter and associated PAHs with higher carcinogenic risk were mainly emitted in the submicrometer size range (<0.1 microm). On the basis of the TEM observations, no relevant effect of the ethanol use on the particulate morphology was evidenced, showing aggregates composed ofprimary particles with mean diameters in the range 17.5-32.5 nm.

  2. Bioethanol/gasoline blends for fuelling conventional and hybrid scooter. Regulated and unregulated exhaust emissions

    NASA Astrophysics Data System (ADS)

    Costagliola, Maria Antonietta; Prati, Maria Vittoria; Murena, Fabio

    2016-05-01

    The aim of this experimental activity was to evaluate the influence of ethanol fuel on the pollutant emissions measured at the exhaust of a conventional and a hybrid scooter. Both scooters are 4-stroke, 125 cm3 of engine capacity and Euro 3 compliant. They were tested on chassis dynamometer for measuring gaseous emissions of CO, HC, NOx, CO2 and some toxic micro organic pollutants, such as benzene, 1,3-butadiene, formaldehyde and acetaldehyde. The fuel consumption was estimated throughout a carbon balance on the exhaust species. Moreover, total particles number with diameter between 20 nm up to 1 μm was measured. Worldwide and European test cycles were carried out with both scooters fuelled with gasoline and ethanol/gasoline blends (10/90, 20/80 and 30/70% vol). According to the experimental results relative to both scooter technologies, the addiction of ethanol in gasoline reduces CO and particles number emissions. The combustion of conventional scooter becomes unstable when a percentage of 30%v of bioethanol is fed; as consequence a strong increasing of hydrocarbon is monitored, including carcinogenic species. The negative effects of ethanol fuel are related to the increasing of fuel consumption due to the less carbon content for volume unit and to the increasing of formaldehyde and acetaldehyde due to the higher oxygen availability. Almost 70% of Ozone Formation Potential is covered by alkenes and aromatics.

  3. Exhaust Emission Rates for Heavy-Duty Onroad Vehicles in the Next Version of MOVES

    EPA Science Inventory

    Derivation of the exhaust and crankcase emission rates for HC, CO, NOx, and PM emissions from medium and heavy-duty diesel, gasoline, and compressed natural gas vehicles. Including updates for emission rates for 2007 and later model year diesel vehicles

  4. 40 CFR 1042.240 - Demonstrating compliance with exhaust emission standards.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... (CONTINUED) AIR POLLUTION CONTROLS CONTROL OF EMISSIONS FROM NEW AND IN-USE MARINE COMPRESSION-IGNITION... the deterioration expected in emissions over your engines' full useful life. See paragraph (e) of this... additive deterioration factor is the difference between exhaust emissions at the end of the useful life...

  5. 40 CFR 1054.105 - What exhaust emission standards must my nonhandheld engines meet?

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... PROTECTION AGENCY (CONTINUED) AIR POLLUTION CONTROLS CONTROL OF EMISSIONS FROM NEW, SMALL NONROAD SPARK... for marine generator engines Class I 10.0 610 5.0 Class II 8.0 610 5.0 (b) Averaging, banking, and...) Other engines: THC emissions. (d) Useful life. Your engines must meet the exhaust emission standards...

  6. 40 CFR 1042.101 - Exhaust emission standards for Category 1 engines and Category 2 engines.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR POLLUTION CONTROLS CONTROL OF EMISSIONS FROM NEW AND IN-USE... the exhaust emission standards when tested using test fuels containing 15 ppm or less sulfur (ultra... engine otherwise requiring an ultra low-sulfur test fuel; however, emissions may not be corrected to...

  7. Exhaust Emission Rates for Heavy-Duty Onroad Vehicles in the Next Version of MOVES

    EPA Science Inventory

    Derivation of the exhaust and crankcase emission rates for HC, CO, NOx, and PM emissions from medium and heavy-duty diesel, gasoline, and compressed natural gas vehicles. Including updates for emission rates for 2007 and later model year diesel vehicles

  8. Measurement of exhaust emissions from two J-58 engines at simulated supersonic cruise flight conditions

    NASA Technical Reports Server (NTRS)

    Holdeman, J. D.

    1976-01-01

    Emissions of total oxides of nitrogen, unburned hydrocarbons, carbon monoxide, and carbon dioxide from two J-58 afterburning turbojet engines at simulated high-altitude flight conditions are reported. Test conditions included flight speeds from Mach 2 to 3 at altitudes from 16 to 23 km. For each flight condition, exhaust measurements were made for four or five power levels from maximum power without afterburning through maximum afterburning. The data show that exhaust emissions vary with flight speed, altitude, power level, and radial position across the exhaust. Oxides of nitrogen (NOX) emissions decreased with increasing altitude, and increased with increasing flight speed. NOX emission indices with afterburning were less than half the value without afterburning. Carbon monoxide and hydrocarbon emissions increased with increasing altitude, and decreased with increasing flight speed. Emissions of these species were substantially higher with afterburning than without.

  9. The Effect of the Diesel Cetane Number on Exhaust Emissions Characteristics by Various Additives

    NASA Astrophysics Data System (ADS)

    Lim, Yunsung; Seo, Choongyeol; Lee, Jongtae; Kang, Daeil; Kim, Jeong Soo; Kim, Hyung Jun

    This paper described the effect of the diesel cetane number on exhaust emissions characteristics according to various additives. In addition, the emission characteristics of test fuels blended with three additives (GTL, biodiesel and additive for improving CN) were analyzed and the potential for uses of these additives were evaluated in this study. To achieve this purpose, the test diesel vehicle with a two-thousand cubic centimeter displacement was used to analyze the emission characteristics according to the CN. Also, the NEDC (New European Driving Cycle) was applied as the test mode which is widely used as the test method for environmental certification of diesel vehicles. To analyze the characteristics of HAPs, the VOCs and PAHs were analyzed from the BTEX and the particulate matter, respectively. The analysis results revealed that the CO emissions show the largest reduction rate while the NOx+THC emissions are reduced at a low as the CN got higher. In the NEDC mode, the PM emissions in the EUDC mode were found to be at a lower level than those in the UDC mode. As for the VOCs and PAHs characteristics, the VOCs of the CN 58 show the lowest amounts. Also, the PAHs of diesel blended with GTL show the highest level, followed by those of diesel blended with biodiesel and diesel blended with cetane additive.

  10. Development of naval diesel engine duty cycles for air exhaust emission environmental impact analysis. Master's thesis

    SciTech Connect

    Markle, S.P.

    1994-05-01

    A strategy for testing naval diesel engines for exhaust emissions was developed. A survey of existing international and national standard diesel engine duty cycles was conducted. All were found to be inadequate for testing and certification of engine exhaust emissions from naval diesel powered ships. Naval ship data covering 11,500 hours of engine operation of four U.S. Navy LSD 41 Class amphibious ships was analyzed to develop a 27 point class operating profile. A procedure combining ship hull form characteristics, ship propulsion plant parameters, and ship operating profile was detailed to derive an 11-Mode duty cycle representative for testing LSD 41 Class propulsion diesel engines. A similar procedure was followed for ship service diesel engines. Comparisons with industry accepted duty cycles were conducted using exhaust emission contour plots for the Colt-Pielstick PC-4B diesel engines. Results showed the 11-Mode LSD 41 Class Duty Cycle best predicted ship propulsion engine emissions compared to the 27 point operating profile propeller curve. The procedure was applied to T-AO 187 Class with similar results. The application of civilian industry standards to measure naval diesel ship propulsion engine exhaust emissions was found to be inadequate. Engine exhaust flow chemistry post turbocharger was investigated using the SANDIA Lab computer tool CHEMKIN. Results showed oxidation and reduction reactions within exhaust gases are quenched in the exhaust stack. Since the exhaust stream in the stack is unreactive, emission sampling may be performed where most convenient. A proposed emission measurement scheme for LSD 41 Class ships was presented.

  11. Determination of the Effects of Speed, Temperature, and Fuel Factors on Exhaust Emissions

    NASA Astrophysics Data System (ADS)

    Chou, Chia-Yang David

    1995-11-01

    This study provided a comprehensive approach to examining the relative significance and possible synergistic effects of speed, temperature, and fuel on mobile source emissions modeling. Eleven passenger vehicles from three fuel delivery system control groups were tested, namely, three from carburetor (CARBU), three from throttle body injection (TBI), and five from multi-port fuel injection (MPFI) group. A minimum of 90 tests were conducted on each vehicle with a random combination of three fuel types (Phase 1, Phase 2, and Indolene), three temperatures (50 F, 75 F, and 100 F), and ten speed cycles. Each vehicle was repeated for ten speed cycles (75 F and Indolene). In general, exhaust emissions descended in the order of CARBU, TBI, and MPFI. All vehicles in the CARBU group contained a "dead" catalyst, which probably explained why vehicles in CARBU were "high emitters.". Results from the paired t-test indicated that exhaust emissions difference between Phase 1 and Phase 2 fuels for all vehicles was significant. The net exhaust emissions reduction of Phase 2 over Phase 1 fuel for HC and NOx was 21% and 12%, respectively; which is in good agreements with the CARB projected 17% HC (including evaporative and exhaust emissions) and 11% CO emissions reduction based on 1996 calendar year when Phase 2 fuel is introduced. Temperature had minimal effects on exhaust emissions especially the test cycles were in hot-stabilized mode. Nevertheless, exhaust emissions from cold-start mode were higher than hot-start mode because the catalyst had not reached to optimal operating temperature during the cold-start mode. The relative contributions of speed, temperature, and fuel to exhaust emissions were determined using analysis of variance (ANOVA) and it was found interaction terms among fuel, speed, and temperature were statistically insignificant. Individually, the temperature and fuel factor played a minor role in exhaust emission modeling. Speed and vehicle type were the two

  12. Using GC×GC-ToF-MS to characterise SVOC from diesel exhaust emissions

    NASA Astrophysics Data System (ADS)

    Alam, M. S.; Ramadhas, A. S.; Stark, C. P.; Liu, D.; Xu, H.; Harrison, R. M.

    2014-12-01

    Despite intensive research over the last 20 years, a number of major research questions remain concerning the sources and properties of road traffic-generated particulate matter. There are major knowledge gaps concerning the composition of primary vehicle exhaust aerosol, and its contribution to secondary organic aerosol (SOA) formation. These uncertainties relate especially to the semi-volatile component of the particles. Semi-Volatile Organic Compounds (SVOC) are compounds which partition directly between the gas and aerosol phases under ambient conditions, and include compounds with saturation concentrations roughly between 0.1 and 104 μg m-3. The SVOC in engine exhaust are typically hydrocarbons in the C15-C35 range. They are largely uncharacterised, other than the n-alkanes, because they are unresolved by traditional gas chromatography and form a large hump in the chromatogram referred to as Unresolved Complex Mixture (UCM). In this study, samples were collected from the exhaust of a diesel engine with and without abatement devices fitted. Engine exhaust was diluted with air and collected using both filter and impaction (MOUDI), to resolve total mass and size resolved mass respectively. Particle size distribution was evaluated by sampling simultaneously with a Scanning Mobility Particle Sizer (SMPS). 2D Gas-Chromatography Time-of-Flight Mass-Spectrometry (GC×GC-ToF-MS) was exploited to characterise and quantify the composition of SVOC from the exhaust emission. The SVOC was observed to contain predominantly n-alkanes, alkyl-cyclohexanes and aromatics; similar to both fresh lubricating oil and fuel. Preliminary results indicate that the contribution of diesel fuel to the exhaust SVOC composition is dominant at high speeds, and a more pronounced contribution from lubricating oil is observed at low speeds. Differences were also observed in the SVOC composition when using different fuel types, engine lubricants, starting temperatures and collecting samples with

  13. Fuel consumptions and exhaust emissions induced by cooperative adaptive cruise control strategies

    NASA Astrophysics Data System (ADS)

    Yu, Shaowei; Shi, Zhongke

    2015-04-01

    Many cooperative adaptive cruise control strategies have been presented to improve traffic efficiency as well as road traffic safety, but scholars have rarely explored the impacts of these strategies on cars' fuel consumptions and exhaust emissions. In this paper, we respectively select two-velocity difference model, multiple velocity difference model and the car-following model considering multiple preceding cars' accelerations to investigate each car's fuel consumptions, carbon monoxide (CO), hydrocarbons (HC) and nitrogen oxides (NOX) emissions and carry out comparative analysis. The comparisons of fuel consumptions and exhaust emissions in three different cruise control strategies show that cooperative cars simulated by the car-following model considering multiple preceding cars' accelerations can run with the minimal fuel consumptions, CO, HC and NOX emissions, thus, taking the car-following model considering multiple preceding cars' accelerations as the cooperative adaptive cruise control strategy can significantly improve cars' fuel efficiency and exhaust emissions.

  14. Polycyclic aromatic hydrocarbon exhaust emissions from different reformulated diesel fuels and engine operating conditions

    NASA Astrophysics Data System (ADS)

    Borrás, Esther; Tortajada-Genaro, Luis A.; Vázquez, Monica; Zielinska, Barbara

    2009-12-01

    The study of light-duty diesel engine exhaust emissions is important due to their impact on atmospheric chemistry and air pollution. In this study, both the gas and the particulate phase of fuel exhaust were analyzed to investigate the effects of diesel reformulation and engine operating parameters. The research was focused on polycyclic aromatic hydrocarbon (PAH) compounds on particulate phase due to their high toxicity. These were analyzed using a gas chromatography-mass spectrometry (GC-MS) methodology. Although PAH profiles changed for diesel fuels with low-sulfur content and different percentages of aromatic hydrocarbons (5-25%), no significant differences for total PAH concentrations were detected. However, rape oil methyl ester biodiesel showed a greater number of PAH compounds, but in lower concentrations (close to 50%) than the reformulated diesel fuels. In addition, four engine operating conditions were evaluated, and the results showed that, during cold start, higher concentrations were observed for high molecular weight PAHs than during idling cycle and that the acceleration cycles provided higher concentrations than the steady-state conditions. Correlations between particulate PAHs and gas phase products were also observed. The emission of PAH compounds from the incomplete combustion of diesel fuel depended greatly on the source of the fuel and the driving patterns.

  15. [Effect of ethanol gasoline and unleaded gasoline on exhaust emissions of EFI vehicles with TWC].

    PubMed

    Wang, Chun-jie; Wang, Wei; Tang, Da-gang; Cui, Ping

    2004-07-01

    The injectors' flow-rate of all test vehicles that each was fixed with a three-way catalytic converter (TWC) and Electronic Fuel Injection System (EFI) was tested including before and after vehicles operated on unleaded and ethanol gasoline respectively running for a long time on real road. The three main engine-out exhaust emissions (HC, CO and NOx) from vehicles operating on different fuels were also analyzed by exhaust testing procedure for the whole light-duty vehicle. Test results showed that comparing with unleaded gasoline and ethanol gasoline has a remarkable effect on decreasing engine-out exhaust emissions of CO and HC (both at about ten percent) and the exhaust emissions of CO, HC and NOx from vehicles with TWC respectively. When burning with unleaded gasoline the three main pollutants from vehicles with TWC have already or nearly reached Europe Exhaust First Standard, after changing to ethanol gasoline CO has drastically decreased at about thirty percent, while HC and NOx decreased at about eighteen and ten percent respectively, at this time which they were all above Europe Exhaust Standard First or nearly reached Europe Exhaust Second Standard; ethanol gasoline has also other better performance such as a slight cleaning function on injectors, a slower deteriorative trend of engine-out CO and HC and a longer operating life-span of TWC.

  16. Alkyl polycyclic aromatic hydrocarbons emissions in diesel/biodiesel exhaust

    NASA Astrophysics Data System (ADS)

    Casal, Carina S.; Arbilla, Graciela; Corrêa, Sergio M.

    2014-10-01

    Polycyclic aromatic hydrocarbons (PAHs) are widely studied in environmental matrices, such as air, water, soil and sediment, because of their toxicity, mutagenicity and carcinogenicity. Because of these properties, the environmental agencies of developed countries have listed sixteen PAHs as priority pollutants. Few countries have limits for these compounds for ambient air, but they only limit emissions from stationary and mobile sources and occupational areas. There are several studies to specifically address the 16 priority PAHs and very little for the alkyl PAHs. These compounds are more abundant, more persistent and frequently more toxic than the non-alkylated PAHs, and the toxicity increases with the number of alkyl substitutions on the aromatic ring. In this study, a method was developed for the analysis of PAHs and alkyl PAHs by using a GC-MS and large injection volume injection coupled with program temperature vaporisation, which allows for limits of detection below 1.0 ng μL-1. Several variables were tested, such as the injection volume, injection velocity, injector initial temperature, duration of the solvent split and others. This method was evaluated in samples from particulate matter from the emissions of engines employing standard diesel, commercial diesel and biodiesel B20. Samples were collected on a dynamometer bench for a diesel engine cycle and the results ranged from 0.5 to 96.9 ng mL-1, indicating that diesel/biodiesel makes a significant contribution to the formation of PAHs and alkyl PAHs.

  17. [Calculating emissions of exhaust particulate matter from motor vehicles with PART5 model].

    PubMed

    Wu, Ye; Hao, Jiming; Li, Wei; Fu, Lixin

    2002-01-30

    PART5, a vehicle particulate emission factor model developed by USEPA, was modified and then used to obtain the emission factors of exhaust PM10 and PM2.5 from on-road automobiles, trucks and motorcycles in Beijing. The total exhaust PM10 and PM2.5 emissions from motor vehicles in 1995 and 1998 were calculated separately. The contribution ratios of different types of vehicles to the total vehicular emissions, and the share of different exhaust particulate components including Pb, direct SO4(2-), soluble organic fraction (SOF) and remaining carbon portion (RCP), were also estimated. It was shown that the emission factors of exhaust PM10 and PM2.5 from gasoline motor vehicles, motorcycles and heavy-duty diesel vehicles in Beijing were 1.7-8.6 times, 2.1-3.5 times and 1.3-1.5 times, respectively, of the USA average emission levels during the same period. The total exhaust PM10 and PM2.5 from vehicles were 2445 tons and 1890 tons in 1995 in Beijing, and increased to 3359 tons and 2694 tons in 1998, which increase by 37.4% and 42.5%, respectively.

  18. Identification of polycyclic aromatic hydrocarbons in unleaded petrol and diesel exhaust emission.

    PubMed

    Yadav, Vinay Kumar; Prasad, Sahdeo; Patel, Devendra K; Khan, Altaf Husain; Tripathi, Madhu; Shukla, Yogeshwer

    2010-09-01

    Inhalation of emissions from petrol and diesel exhaust particulates is associated with potentially severe biological effects. In the present study, polycyclic aromatic hydrocarbons (PAHs) were identified from smokes released by the automobile exhaust from petrol and diesel. Intensive sampling of unleaded petrol and diesel exhaust were done by using 800-cm(3) motor car and 3,455-cm(3) vehicle, respectively. The particulate phase of exhaust was collected on Whatman filter paper. Particulate matters were extracted from filter paper by using Soxhlet. PAHs were identified from particulate matter by reverse phase high performance liquid chromatography using C(18) column. A total of 14 PAHs were identified in petrol and 13 in case of diesel sample after comparing to standard samples for PAH estimation. These inhalable PAHs released from diesel and petrol exhaust are known to possess mutagenic and carcinogenic activity, which may present a potential risk for the health of inhabitants.

  19. 40 CFR 1054.107 - What is the useful life period for meeting exhaust emission standards?

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... ascertain when engine performance deteriorates to the point where usefulness and/or reliability is impacted...-IGNITION ENGINES AND EQUIPMENT Emission Standards and Related Requirements § 1054.107 What is the useful life period for meeting exhaust emission standards? This section describes an engine family's useful...

  20. 40 CFR 1054.107 - What is the useful life period for meeting exhaust emission standards?

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 33 2014-07-01 2014-07-01 false What is the useful life period for... life period for meeting exhaust emission standards? This section describes an engine family's useful life, which is the period during which engines are required to comply with all emission standards that...

  1. 40 CFR 1051.105 - What are the exhaust emission standards for off-highway motorcycles?

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... useful life for the engine family in terms of kilometers if the average service life of your vehicles is... minimum useful life (10,000 kilometers). In determining the actual average service life of vehicles in an... VEHICLES Emission Standards and Related Requirements § 1051.105 What are the exhaust emission standards...

  2. 40 CFR 1051.105 - What are the exhaust emission standards for off-highway motorcycles?

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... useful life for the engine family in terms of kilometers if the average service life of your vehicles is... minimum useful life (10,000 kilometers). In determining the actual average service life of vehicles in an... VEHICLES Emission Standards and Related Requirements § 1051.105 What are the exhaust emission standards...

  3. 40 CFR 1051.105 - What are the exhaust emission standards for off-highway motorcycles?

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... useful life for the engine family in terms of kilometers if the average service life of your vehicles is... minimum useful life (10,000 kilometers). In determining the actual average service life of vehicles in an... VEHICLES Emission Standards and Related Requirements § 1051.105 What are the exhaust emission standards...

  4. 40 CFR 1051.105 - What are the exhaust emission standards for off-highway motorcycles?

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... useful life for the engine family in terms of kilometers if the average service life of your vehicles is... minimum useful life (10,000 kilometers). In determining the actual average service life of vehicles in an... VEHICLES Emission Standards and Related Requirements § 1051.105 What are the exhaust emission standards...

  5. 40 CFR 1051.105 - What are the exhaust emission standards for off-highway motorcycles?

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... useful life for the engine family in terms of kilometers if the average service life of your vehicles is... minimum useful life (10,000 kilometers). In determining the actual average service life of vehicles in an... VEHICLES Emission Standards and Related Requirements § 1051.105 What are the exhaust emission standards...

  6. 40 CFR 1045.101 - What exhaust emission standards and requirements must my engines meet?

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 34 2012-07-01 2012-07-01 false What exhaust emission standards and requirements must my engines meet? 1045.101 Section 1045.101 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR POLLUTION CONTROLS CONTROL OF EMISSIONS FROM SPARK-IGNITION PROPULSION...

  7. 40 CFR 1045.101 - What exhaust emission standards and requirements must my engines meet?

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 34 2013-07-01 2013-07-01 false What exhaust emission standards and requirements must my engines meet? 1045.101 Section 1045.101 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR POLLUTION CONTROLS CONTROL OF EMISSIONS FROM SPARK-IGNITION PROPULSION...

  8. 40 CFR 1045.101 - What exhaust emission standards and requirements must my engines meet?

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 33 2011-07-01 2011-07-01 false What exhaust emission standards and requirements must my engines meet? 1045.101 Section 1045.101 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR POLLUTION CONTROLS CONTROL OF EMISSIONS FROM SPARK-IGNITION PROPULSION...

  9. 40 CFR 1045.101 - What exhaust emission standards and requirements must my engines meet?

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 33 2014-07-01 2014-07-01 false What exhaust emission standards and requirements must my engines meet? 1045.101 Section 1045.101 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR POLLUTION CONTROLS CONTROL OF EMISSIONS FROM SPARK-IGNITION PROPULSION...

  10. 40 CFR 1045.105 - What exhaust emission standards must my sterndrive/inboard engines meet?

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 34 2013-07-01 2013-07-01 false What exhaust emission standards must my sterndrive/inboard engines meet? 1045.105 Section 1045.105 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR POLLUTION CONTROLS CONTROL OF EMISSIONS FROM SPARK-IGNITION...

  11. 40 CFR 1054.105 - What exhaust emission standards must my nonhandheld engines meet?

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... engines with displacement at or above 100 cc. (3) 12.1 for Class II engines. (c) Fuel types. The exhaust emission standards in this section apply for engines using the fuel type on which the engines in the... this section based on the following types of hydrocarbon emissions for engines powered by the following...

  12. 40 CFR 1054.105 - What exhaust emission standards must my nonhandheld engines meet?

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... engines with displacement at or above 100 cc. (3) 12.1 for Class II engines. (c) Fuel types. The exhaust emission standards in this section apply for engines using the fuel type on which the engines in the... this section based on the following types of hydrocarbon emissions for engines powered by the following...

  13. 40 CFR 1054.103 - What exhaust emission standards must my handheld engines meet?

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... g/kW-hr for Class IV engines. (3) 186 g/kW-hr for Class V engines. (c) Fuel types. The exhaust emission standards in this section apply for engines using the fuel type on which the engines in the... this section based on the following types of hydrocarbon emissions for engines powered by the following...

  14. 40 CFR 1054.103 - What exhaust emission standards must my handheld engines meet?

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... g/kW-hr for Class IV engines. (3) 186 g/kW-hr for Class V engines. (c) Fuel types. The exhaust emission standards in this section apply for engines using the fuel type on which the engines in the... this section based on the following types of hydrocarbon emissions for engines powered by the following...

  15. 40 CFR 1054.103 - What exhaust emission standards must my handheld engines meet?

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... g/kW-hr for Class IV engines. (3) 186 g/kW-hr for Class V engines. (c) Fuel types. The exhaust emission standards in this section apply for engines using the fuel type on which the engines in the... this section based on the following types of hydrocarbon emissions for engines powered by the following...

  16. 40 CFR 1054.105 - What exhaust emission standards must my nonhandheld engines meet?

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... engines with displacement at or above 100 cc. (3) 12.1 for Class II engines. (c) Fuel types. The exhaust emission standards in this section apply for engines using the fuel type on which the engines in the... this section based on the following types of hydrocarbon emissions for engines powered by the following...

  17. 40 CFR 1054.105 - What exhaust emission standards must my nonhandheld engines meet?

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... engines with displacement at or above 100 cc. (3) 12.1 for Class II engines. (c) Fuel types. The exhaust emission standards in this section apply for engines using the fuel type on which the engines in the... this section based on the following types of hydrocarbon emissions for engines powered by the following...

  18. 40 CFR 1054.103 - What exhaust emission standards must my handheld engines meet?

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... g/kW-hr for Class IV engines. (3) 186 g/kW-hr for Class V engines. (c) Fuel types. The exhaust emission standards in this section apply for engines using the fuel type on which the engines in the... this section based on the following types of hydrocarbon emissions for engines powered by the following...

  19. 77 FR 76842 - Exhaust Emissions Standards for New Aircraft Gas Turbine Engines and Identification Plate for...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-12-31

    ... action revises the standards for oxides of nitrogen and test procedures for exhaust emissions based on... Environmental Protection Agency (EPA) proposed new aircraft engine emission standards for oxides of nitrogen (NO... Protection (CAEP) of ICAO uses to differentiate the CAEP work cycles that produce new standards. For...

  20. 40 CFR 89.111 - Averaging, banking, and trading of exhaust emissions.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 20 2010-07-01 2010-07-01 false Averaging, banking, and trading of... ENGINES Emission Standards and Certification Provisions § 89.111 Averaging, banking, and trading of exhaust emissions. Regulations regarding the availability of an averaging, banking, and trading...

  1. 40 CFR 1042.104 - Exhaust emission standards for Category 3 engines.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... (CONTINUED) AIR POLLUTION CONTROLS CONTROL OF EMISSIONS FROM NEW AND IN-USE MARINE COMPRESSION-IGNITION... subject to not-to-exceed standards. (d) Useful life. Your engines must meet the exhaust emission standards of this section over their full useful life, expressed as a period in years or hours of...

  2. 40 CFR 1042.104 - Exhaust emission standards for Category 3 engines.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... (CONTINUED) AIR POLLUTION CONTROLS CONTROL OF EMISSIONS FROM NEW AND IN-USE MARINE COMPRESSION-IGNITION... engines are not subject to not-to-exceed standards. (d) Useful life. Your engines must meet the exhaust emission standards of this section over their full useful life, expressed as a period in years or hours...

  3. 40 CFR 1042.104 - Exhaust emission standards for Category 3 engines.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... (CONTINUED) AIR POLLUTION CONTROLS CONTROL OF EMISSIONS FROM NEW AND IN-USE MARINE COMPRESSION-IGNITION... subject to not-to-exceed standards. (d) Useful life. Your engines must meet the exhaust emission standards of this section over their full useful life, expressed as a period in years or hours of...

  4. 40 CFR 1042.104 - Exhaust emission standards for Category 3 engines.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... (CONTINUED) AIR POLLUTION CONTROLS CONTROL OF EMISSIONS FROM NEW AND IN-USE MARINE COMPRESSION-IGNITION... engines are not subject to not-to-exceed standards. (d) Useful life. Your engines must meet the exhaust emission standards of this section over their full useful life, expressed as a period in years or hours...

  5. An assessment of consistence of exhaust gas emission test results obtained under controlled NEDC conditions

    NASA Astrophysics Data System (ADS)

    Balawender, K.; Jaworski, A.; Kuszewski, H.; Lejda, K.; Ustrzycki, A.

    2016-09-01

    Measurements concerning emissions of pollutants contained in automobile combustion engine exhaust gases is of primary importance in view of their harmful impact on the natural environment. This paper presents results of tests aimed at determining exhaust gas pollutant emissions from a passenger car engine obtained under repeatable conditions on a chassis dynamometer. The test set-up was installed in a controlled climate chamber allowing to maintain the temperature conditions within the range from -20°C to +30°C. The analysis covered emissions of such components as CO, CO2, NOx, CH4, THC, and NMHC. The purpose of the study was to assess repeatability of results obtained in a number of tests performed as per NEDC test plan. The study is an introductory stage of a wider research project concerning the effect of climate conditions and fuel type on emission of pollutants contained in exhaust gases generated by automotive vehicles.

  6. Diesel emission reduction using internal exhaust gas recirculation

    DOEpatents

    He, Xin [Denver, CO; Durrett, Russell P [Bloomfield Hills, MI

    2012-01-24

    A method for controlling combustion in a direct-injection diesel engine includes monitoring a crankshaft rotational position of a cylinder of the engine, monitoring an engine load, determining an intake stroke within the cylinder based upon the crankshaft rotational position, and when the engine load is less than a threshold engine load, opening an exhaust valve for the cylinder during a portion of the intake stroke.

  7. 40 CFR 86.1342-90 - Calculations; exhaust emissions.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... emission level (HC, CO, CO2. or NOX) in grams per brake horsepower-hour and, if appropriate, the weighted mass total hydrocarbon equivalent, in grams per brake horsepower-hour. (2) gC = Mass emission level in grams or grams carbon mass equivalent, measured during the cold start test. (3) gH = Mass emission...

  8. 40 CFR 86.1342-90 - Calculations; exhaust emissions.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... emission level (HC, CO, CO2. or NOX) in grams per brake horsepower-hour and, if appropriate, the weighted mass total hydrocarbon equivalent, in grams per brake horsepower-hour. (2) gC = Mass emission level in grams or grams carbon mass equivalent, measured during the cold start test. (3) gH = Mass emission...

  9. 40 CFR 86.1342-90 - Calculations; exhaust emissions.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... emission level (HC, CO, CO2. or NOX) in grams per brake horsepower-hour and, if appropriate, the weighted mass total hydrocarbon equivalent, in grams per brake horsepower-hour. (2) gC = Mass emission level in grams or grams carbon mass equivalent, measured during the cold start test. (3) gH = Mass emission...

  10. 40 CFR 86.1342-90 - Calculations; exhaust emissions.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... emission level (HC, CO, CO2. or NOX) in grams per brake horsepower-hour and, if appropriate, the weighted mass total hydrocarbon equivalent, in grams per brake horsepower-hour. (2) gC = Mass emission level in grams or grams carbon mass equivalent, measured during the cold start test. (3) gH = Mass emission...

  11. 40 CFR 86.1777-99 - Calculations; exhaust emissions.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... factor applicable to the vehicle emission control technology category and fuel. The product of the NMOG... light-duty trucks: Vehicle emission control technology category Fuel Reactivity adjustment factor TLEVs... light-duty vehicles and light-duty trucks: Vehicle emission control technology category Methane...

  12. 40 CFR 1033.101 - Exhaust emission standards.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... this section. Generating or using emission credits requires that you specify a family emission limit (FEL) for each pollutant you include in the ABT program for each engine family. These FELs serve as the emission standards for the engine family with respect to all required testing instead of the standards...

  13. 40 CFR 1033.101 - Exhaust emission standards.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... this section. Generating or using emission credits requires that you specify a family emission limit (FEL) for each pollutant you include in the ABT program for each engine family. These FELs serve as the emission standards for the engine family with respect to all required testing instead of the standards...

  14. 40 CFR 1033.101 - Exhaust emission standards.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... this section. Generating or using emission credits requires that you specify a family emission limit (FEL) for each pollutant you include in the ABT program for each engine family. These FELs serve as the emission standards for the engine family with respect to all required testing instead of the standards...

  15. Experimental evaluation of exhaust mixers for an Energy Efficient Engine

    NASA Technical Reports Server (NTRS)

    Kozlowski, H.; Kraft, G.

    1980-01-01

    Static scale model tests were conducted to evaluate exhaust system mixers for a high bypass ratio engine as part of the NASA sponsored Energy Efficient program. Gross thrust coefficients were measured for a series of mixer configurations which included variations in the number of mixer lobes, tailpipe length, mixer penetration, and length. All of these parameters have a significant impact on exhaust system performance. In addition, flow visualization pictures and pressure/temperature traverses were obtained for selected configurations. Parametric performance trends are discussed and the results considered relative to the Energy Efficient Engine program goals.

  16. Urban air quality: the challenge of traffic non-exhaust emissions.

    PubMed

    Amato, Fulvio; Cassee, Flemming R; Denier van der Gon, Hugo A C; Gehrig, Robert; Gustafsson, Mats; Hafner, Wolfgang; Harrison, Roy M; Jozwicka, Magdalena; Kelly, Frank J; Moreno, Teresa; Prevot, Andre S H; Schaap, Martijn; Sunyer, Jordi; Querol, Xavier

    2014-06-30

    About 400,000 premature adult deaths attributable to air pollution occur each year in the European Region. Road transport emissions account for a significant share of this burden. While important technological improvements have been made for reducing particulate matter (PM) emissions from motor exhausts, no actions are currently in place to reduce the non-exhaust part of emissions such as those from brake wear, road wear, tyre wear and road dust resuspension. These "non-exhaust" sources contribute easily as much and often more than the tailpipe exhaust to the ambient air PM concentrations in cities, and their relative contribution to ambient PM is destined to increase in the future, posing obvious research and policy challenges. This review highlights the major and more recent research findings in four complementary fields of research and seeks to identify the current gaps in research and policy with regard to non-exhaust emissions. The objective of this article is to encourage and direct future research towards an improved understanding on the relationship between emissions, concentrations, exposure and health impact and on the effectiveness of potential remediation measures in the urban environment.

  17. Non-exhaust emissions of PM and the efficiency of emission reduction by road sweeping and washing in the Netherlands.

    PubMed

    Keuken, Menno; Denier van der Gon, Hugo; van der Valk, Karin

    2010-09-15

    From research on PM(2.5) and PM(10) in 2007/2008 in the Netherlands, it was concluded that the coarse fraction (PM(2.5-10)) attributed 60% and 50% respectively, to the urban-regional and street-urban increments of PM(10). Contrary to Scandinavian and Mediterranean countries which exhibit significant seasonal variation in the coarse fraction of particulate matter (PM), in the Netherlands the coarse fraction in PM at a street location is rather constant during the year. Non-exhaust emissions by road traffic are identified as the main source for coarse PM in urban areas. Non-exhaust emissions mainly originate from re-suspension of accumulated deposited PM and road wear related particles, while primary tire and brake wear hardly contribute to the mass of non-exhaust emissions. However, tire and brake wear can clearly be identified in the total mass through the presence of the heavy metals: zinc, a tracer for tire wear and copper, a tracer for brake wear. The efficiency of road sweeping and washing to reduce non-exhaust emissions in a street-canyon in Amsterdam was investigated. The increments of the coarse fraction at a kerbside location and a housing façade location versus the urban background were measured at days with and without sweeping and washing. It was concluded that this measure did not significantly reduce non-exhaust emissions.

  18. [Emission characteristics of polycyclic aromatic hydrocarbons in exhaust particles from a diesel car].

    PubMed

    Tan, Pi-Qiang; Zhou, Zhou; Hu, Zhi-Yuan; Lou, Di-Ming

    2013-03-01

    The emission characteristics of polycyclic aromatic hydrocarbons (PAHs) in exhaust particles from a diesel car were studied. In the experiment, pure diesel fuel and B10 fuel with a biodiesel blend ratio of 10% were chosen. The gaseous emissions of HC, CO and NO(x) under New European Driving Cycle (NEDC) were measured, and exhaust particulate matter (PM) samples were analyzed by gas chromatography-mass spectrometry. The emission characteristics of PAHs in exhaust particles were highlighted. The results show that the emission concentrations of HC, CO, NO(x), and PM decreased when the diesel car used B10 fuel. Fluoranthene and pyrene were dominant in PAHs of PM emissions when the diesel car used pure diesel or B10 fuel. Compared to pure diesel, there was a slight increase in low-ring PAHs emissions when the diesel car used B10 fuel. On the contrary, PAHs emissions in middle and high-ring declined significantly. Besides, Benzo [ a] pyrene equivalent toxicity analysis results show that the BEQs of B10 fuel decreased by 21.6% compared to pure diesel. That means the toxicity of PAHs in exhaust particles declined when the diesel car used biodiesel fuel.

  19. 40 CFR 1037.106 - Exhaust emission standards for CO2 for tractors above 26,000 pounds GVWR.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 34 2012-07-01 2012-07-01 false Exhaust emission standards for CO2 for... Emission Standards and Related Requirements § 1037.106 Exhaust emission standards for CO2 for tractors above 26,000 pounds GVWR. (a) The CO2 standards of this section apply for tractors above 26,000...

  20. 40 CFR 1037.106 - Exhaust emission standards for CO2 for tractors above 26,000 pounds GVWR.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 34 2013-07-01 2013-07-01 false Exhaust emission standards for CO2 for... Emission Standards and Related Requirements § 1037.106 Exhaust emission standards for CO2 for tractors above 26,000 pounds GVWR. (a) The CO2 standards of this section apply for tractors above 26,000...

  1. 40 CFR 1037.106 - Exhaust emission standards for CO2 for tractors above 26,000 pounds GVWR.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 33 2014-07-01 2014-07-01 false Exhaust emission standards for CO2 for... Emission Standards and Related Requirements § 1037.106 Exhaust emission standards for CO2 for tractors above 26,000 pounds GVWR. (a) The CO2 standards of this section apply for tractors above 26,000...

  2. On-Road Measurement of Exhaust Emission Factors for Individual Diesel Trucks

    NASA Astrophysics Data System (ADS)

    Dallmann, T. R.; DeMartini, S.; Harley, R. A.; Kirchstetter, T. W.; Wood, E. C.; Onasch, T. B.; Herndon, S. C.

    2011-12-01

    Diesel trucks are an important source of primary fine particulate matter (PM2.5) that includes black carbon (BC) as a major component. More stringent exhaust emission standards for new engines, effective starting in 2007, considerably reduce allowable emissions and have led to use of after-treatment control devices such as diesel particle filters. The state of California is also implementing programs to accelerate replacement or retrofit of older trucks. In light of these changes, measurements of emissions from in-use heavy-duty diesel trucks are timely and needed to understand the impact of new control technologies on emissions. PM2.5, BC mass, particle light absorption, and particle light extinction emission factors for hundreds of individual diesel trucks were measured in this study. Emissions were measured in July 2010 from trucks driving through the Caldecott tunnel in the San Francisco Bay area. Gas-phase emissions including nitric oxide, nitrogen dioxide, carbon monoxide, and carbon dioxide (CO2) were also measured. Pollutants were measured using air sampling inlets located directly above the vertical exhaust stacks of heavy-duty trucks driving by on the roadway below. All of these measurements were made using fast time response (1 Hz) sensors. Particle optical properties were simultaneously characterized with direct measurements of absorption (babs) and extinction (bext) coefficients. Emission factors for individual trucks were calculated using a carbon balance method in which emissions of PM2.5, BC, babs, and bext in each exhaust plume were normalized to emissions of CO2. Emission factor distributions and fleet-average values are quantified. Absorption and extinction emission factors are used to calculate the aerosol single scattering albedo and BC mass absorption efficiency for individual truck exhaust plumes.

  3. The characteristics of performance and exhaust emissions of a diesel engine using a biodiesel with antioxidants.

    PubMed

    Ryu, Kyunghyun

    2010-01-01

    The aim of this study is to investigate the effects of antioxidants on the oxidation stability of biodiesel fuel, the engine performance and the exhaust emissions of a diesel engine. Biodiesel fuel used in the study was derived from soybean oil. The results show that the efficiency of antioxidants is in the order TBHQ>PrG>BHA>BHT>alpha-tocopherol. The oxidative stability of biodiesel fuel attained the 6-h quality standard with 100 ppm TBHQ and with 300 ppm PrG in biodiesel fuel. Combustion characteristics and exhaust emissions in diesel engine were not influenced by the addition of antioxidants in biodiesel fuel. The BSFC of biodiesel fuel with antioxidants decreased more than that of biodiesel fuel without antioxidants, but no trends were observed according to the type or amount of antioxidant. Antioxidants had few effects on the exhaust emissions of a diesel engine running on biodiesel.

  4. Evaluation of Federal Aviation Administration ion engine exhaust sampling rake

    NASA Technical Reports Server (NTRS)

    Fiorentino, A. J.; Greene, W.; Roberts, R.

    1977-01-01

    A FAA exhaust emissions rake was tested in the Experimental Clean Combustor Program, Phase 3 to permit comparison of the values of gaseous emissions and smoke measured by the FAA rake with those measured with the NASA Pratt and Whitney Aircraft (P and WA) rake used in the Phase 3 Experimental Clean Combustor Program and with station seven probes. The results showed that the levels of CO, THC, NOx and smoke measured by the FAA and NASA/P and WA rakes agree well at high power, but that CO emissions measured by the FAA rake were approximately 10 percent higher than those measured by the NASA/P and WA rake at low power.

  5. 40 CFR 86.144-94 - Calculations; exhaust emissions.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ..., CO, THCE, NMHC, NMHCE, CH4, NOX, or CO2, in grams per vehicle mile. (2) Yct=Mass emissions as calculated from the “transient” phase of the cold start test, in grams per test phase. (3) Yht=Mass emissions as calculated from the “transient” phase of the hot start test, in grams per test phase. (4)...

  6. 40 CFR 86.144-94 - Calculations; exhaust emissions.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ..., CO, THCE, NMHC, NMHCE, CH4, NOX, or CO2, in grams per vehicle mile. (2) Yct=Mass emissions as calculated from the “transient” phase of the cold start test, in grams per test phase. (3) Yht=Mass emissions as calculated from the “transient” phase of the hot start test, in grams per test phase. (4)...

  7. 40 CFR 86.144-94 - Calculations; exhaust emissions.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ..., CO, THCE, NMHC, NMHCE, CH4, NOX, or CO2, in grams per vehicle mile. (2) Yct = Mass emissions as calculated from the “transient” phase of the cold start test, in grams per test phase. (3) Yht = Mass emissions as calculated from the “transient” phase of the hot start test, in grams per test phase. (4)...

  8. 40 CFR 86.144-94 - Calculations; exhaust emissions.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ..., CO, THCE, NMHC, NMHCE, CH4, NOX, or CO2, in grams per vehicle mile. (2) Yct=Mass emissions as calculated from the “transient” phase of the cold start test, in grams per test phase. (3) Yht=Mass emissions as calculated from the “transient” phase of the hot start test, in grams per test phase. (4)...

  9. 40 CFR 86.144-94 - Calculations; exhaust emissions.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ..., CO, THCE, NMHC, NMHCE, CH4, NOX, or CO2, in grams per vehicle mile. (2) Yct=Mass emissions as calculated from the “transient” phase of the cold start test, in grams per test phase. (3) Yht=Mass emissions as calculated from the “transient” phase of the hot start test, in grams per test phase. (4)...

  10. 40 CFR 86.1544 - Calculation; idle exhaust emissions.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... PROGRAMS (CONTINUED) CONTROL OF EMISSIONS FROM NEW AND IN-USE HIGHWAY VEHICLES AND ENGINES (CONTINUED) Emission Regulations for Otto-Cycle Heavy-Duty Engines, New Methanol-Fueled Natural Gas-Fueled, and... Methanol-Fueled Natural Gas-Fueled, and Liquefied Petroleum Gas-Fueled Diesel-Cycle Light-Duty Trucks;...

  11. Examination of Acute Pulmonary Responses to Various Cookstove Exhaust Emissions

    EPA Science Inventory

    Air pollution is a global public heath problem, to which the emissions from rudimentary cooking devices has been estimated to contribute significantly through the burning of various types of biomass. Notably, exposure to cookstove emissions (CE) has been linked to increases in mo...

  12. Examination of Acute Pulmonary Responses to Various Cookstove Exhaust Emissions

    EPA Science Inventory

    Air pollution is a global public heath problem, to which the emissions from rudimentary cooking devices has been estimated to contribute significantly through the burning of various types of biomass. Notably, exposure to cookstove emissions (CE) has been linked to increases in mo...

  13. [Preparation of ethanol-diesel fuel blends and exhausts emission characteristics in diesel engine].

    PubMed

    Zhang, Runduo; He, Hong; Zhang, Changbin; Shi, Xiaoyan

    2003-07-01

    The technology that diesel oil is partly substituted by ethanol can reduce diesel engine exhausts emission, especially fuel soot. This research is concentrated on preparation of ethanol-diesel blend fuel and exhausts emission characteristics using diesel engine bench. Absolute ethanol can dissolve into diesel fuel at an arbitrary ratio. However, a trace of water (0.2%) addition can lead to the phase separation of blends. Organic additive synthesized during this research can develop the ability of resistance to water and maintain the stability of ethanol-diesel-trace amounts of water system. The effects of 10%, 20%, and 30% ethanol-diesel fuel blends on exhausts emission, were compared with that of diesel fuel in direct injection (DI) diesel engine. The optimum ethanol percentage for ethanol-diesel fuel blends was 20%. Using 20% ethanol-diesel fuel blend with 2% additive of the total volume, bench diesel engine showed a large amount decrease of exhaust gas, e.g. 55% of Bosch smoke number, 70% of HC emission, and 45% of CO emission at 13 kW and 1540 r/min. Without the addition of additive, the blend of ethanol produced new organic compounds such as ethanol and acetaldehyde in tail gas. However, the addition of additive obviously reduced the emission of ethanol and acetaldehyde.

  14. The effect of gasoline RVP on exhaust emissions from current European vehicles

    SciTech Connect

    Bennett, P.J.; Beckwith, P.; Goodfellow, C.L.; Skaardalsmo, K.

    1995-12-31

    The effect of gasoline RVP on regulated exhaust emissions has been investigated in a fleet consisting of five current European vehicles. The effects of MTBE with changing RVP and E70 were also studied. All vehicles were equipped with the standard OEM small carbon canisters and three-way catalytic converters and the regulated emissions measured over the new European test cycle. A rigorous refueling protocol was employed to ensure that the carbon canisters were loaded in a repeatable way before the emission tests. The results show that a reduction in RVP gave benefits in CO and NOx, but no effect on exhaust THC emissions. The benefits for CO and NOx were greater in non-oxygenated fuels. Of the five test vehicles, three showed CO emission benefits due to RVP reduction, while CO from the other two was insensitive to RVP changes. Four vehicles also showed NOx emission benefits due to RVP reduction while the NOx emissions from the other vehicle were insensitive to RVP changes. The benefits of reducing RVP were observed for the fleet over all three phases of the cycle, however, the largest percentage of changes were seen after the vehicles had warmed up. Although no significant overall effect of RVP on exhaust THC emissions was apparent, reductions in THC over the ECE 3+4 and EUDC phases were observed. At high RVP MTBE addition gave reductions in CO and NOx emissions, but at low RVP no emission reductions were observed. A reduction in E70 only influenced exhaust THC emissions, resulting in a small increase.

  15. Effect of Methyl Tertiary Butyl Ether Concentrations on Exhaust Emissions from Gasoline Used in the Metropolitan Area of Mexico City.

    PubMed

    Schifter, Isaac; Dfaz, Luis; Avalos, Sergio; Vera, Mario; Barrera, Adrian; López-Salinas, Esteban

    2000-04-01

    In this work, the primary objective was to assess the impact of oxygenated fuel on the exhaust emissions from an important fraction of vehicles in the Metropolitan Area of Mexico City (MAMC). The results aim to provide information on the actual effect of MTBE on a fleet that represents more than 60% of the in-use vehicles in the MAMC. Ten vehicles were tested with a low-octane base gasoline, and 10 more with a regular-grade unleaded base gasoline. Three MTBE concentrations, 5, 10, and 15 vol %, were tested following the U.S. Federal Test Procedure (FTP). CO, total HC, and NOx from the exhaust gases were quantitatively evaluated and also characterized for FTP speciated organic emissions. From this data, the O3-forming potential of the fuels was calculated. Results show that for the fleet using low-octane gasoline, the addition of 10% MTBE substantially reduced CO emissions, but total HC concentration in the exhaust showed a modest decrease. For the regular gasoline, the 10% MTBE blend seemed to be the best choice, but there was not a significant decrease in emissions. The specific reactivity of each fuel, expressed in grams of O3 per gram of nonmethane organic gases, increased with MTBE concentration in both cases. This result is important to consider, especially for a region like Mexico City, which has high atmospheric O3 concentrations.

  16. Effect of methyl tertiary butyl ether concentrations on exhaust emissions from gasoline used in the metropolitan area of Mexico City.

    PubMed

    Schifter, I; Díaz, L; Avalos, S; Vera, M; Barrera, A; López-Salinas, E

    2000-04-01

    In this work, the primary objective was to assess the impact of oxygenated fuel on the exhaust emissions from an important fraction of vehicles in the Metropolitan Area of Mexico City (MAMC). The results aim to provide information on the actual effect of MTBE on a fleet that represents more than 60% of the in-use vehicles in the MAMC. Ten vehicles were tested with a low-octane base gasoline, and 10 more with a regular-grade unleaded base gasoline. Three MTBE concentrations, 5, 10, and 15 vol %, were tested following the U.S. Federal Test Procedure (FTP). CO, total HC, and NOx from the exhaust gases were quantitatively evaluated and also characterized for FTP speciated organic emissions. From this data, the O3-forming potential of the fuels was calculated. Results show that for the fleet using low-octane gasoline, the addition of 10% MTBE substantially reduced CO emissions, but total HC concentration in the exhaust showed a modest decrease. For the regular gasoline, the 10% MTBE blend seemed to be the best choice, but there was not a significant decrease in emissions. The specific reactivity of each fuel, expressed in grams of O3 per gram of nonmethane organic gases, increased with MTBE concentration in both cases. This result is important to consider, especially for a region like Mexico City, which has high atmospheric O3 concentrations.

  17. Jet engine exhaust emissions of high altitude commercial aircraft projected to 1990

    NASA Technical Reports Server (NTRS)

    Grobman, J.; Ingebo, R. D.

    1974-01-01

    Projected minimum levels of engine exhaust emissions that may be practicably achievable for future commercial aircraft operating at high-altitude cruise conditions are presented. The forecasts are based on:(1) current knowledge of emission characteristics of combustors and augmentors; (2) the status of combustion research in emission reduction technology; and (3) predictable trends in combustion systems and operating conditions as required for projected engine designs that are candidates for advanced subsonic or supersonic commercial aircraft fueled by either JP fuel, liquefied natural gas, or hydrogen. Results are presented for cruise conditions in terms of both an emission index (g constituent/kg fuel) and an emission rate (g constituent/hr).

  18. Forecast of jet engine exhaust emissions for future high altitude commercial aircraft

    NASA Technical Reports Server (NTRS)

    Grobman, J.; Ingebo, R. D.

    1974-01-01

    Projected minimum levels of engine exhaust emissions that may be practicably achievable for future commercial aircraft operating at high altitude cruise conditions are presented. The forecasts are based on: (1) current knowledge of emission characteristics of combustors and augmentors; (2) the current status of combustion research in emission reduction technology; (3) predictable trends in combustion systems and operating conditions as required for projected engine designs that are candidates for advanced subsonic or supersonic commercial aircraft. Results are presented for cruise conditions in terms of an emission index, g pollutant/kg fuel. Two sets of engine exhaust emission predictions are presented: the first, based on an independent NASA study and the second, based on the consensus of an ad hoc committee composed of industry, university, and government representatives. The consensus forecasts are in general agreement with the NASA forecasts.

  19. Real-time exhaust gas modular flowmeter and emissions reporting system for mobile apparatus

    NASA Technical Reports Server (NTRS)

    Breton, Leo Alphonse Gerard (Inventor)

    2002-01-01

    A real-time emissions reporting system includes an instrument module adapted to be detachably connected to the exhaust pipe of a combustion engine to provide for flow of exhaust gas therethrough. The instrument module includes a differential pressure probe which allows for determination of flow rate of the exhaust gas and a gas sampling tube for continuously feeding a sample of the exhaust gas to a gas analyzer or a mounting location for a non-sampling gas analyzer. In addition to the module, the emissions reporting system also includes an elastomeric boot for detachably connecting the module to the exhaust pipe of the combustion engine, a gas analyzer for receiving and analyzing gases sampled within the module and a computer for calculating pollutant mass flow rates based on concentrations detected by the gas analyzer and the detected flowrate of the exhaust gas. The system may also include a particulate matter detector with a second gas sampling tube feeding same mounted within the instrument module.

  20. 40 CFR 1033.101 - Exhaust emission standards.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... other locomotives: THC emissions for Tier 3 and earlier locomotives and NMHC for Tier 4. Note that manufacturers/remanufacturers may choose to not measure NMHC and assume that NMHC is equal to THC multiplied by...

  1. Studies on health effects of automotive exhaust emissions. How dangerous are diesel emissions?

    PubMed

    Klingenberg, H; Winneke, H

    1990-04-01

    The following paper indicates that current results of research conducted on the effects of intentionally increased concentrations of diesel engine exhaust emissions, particularly the results of animal experiments, do not lead scientifically to final conclusions. According to the current level of knowledge, we must continue to assume that the risk of cancer, possibly due to diesel particles, is negligible, particularly under real environmental conditions. The preventive measures taken by governments are of course supported by the automotive industry, an additional research outlay, however, is necessary not only to clear up contradictions and answer new questions arising from current test results, but also to take positive, and not merely precautionary, action in the future. Due to its links to other influences on humans and plants, research conducted on the effects of motor vehicle emissions is a task that lies very much in the public interest. At the same time, the overview of concluded and ongoing research objectives presented in this paper indicates that the automotive industry is greatly committed to this issue and will meet well-justified expectations.

  2. Ground-based aircraft exhaust measurements of a Lufthansa Airbus A340 using FTIR emission spectrometry

    NASA Astrophysics Data System (ADS)

    Schaefer, Klaus; Heland, Joerg

    1999-01-01

    The emission inventories of aircraft emissions are being set up using flight routing data and test rig measurements of the engine manufacturers for certification purposes which have to be extrapolated with respect to the actual parameters at cruise altitude. Precise data from in-service engines are not existing. FTIR-emission-spectroscopy as a remote sensing multi-component exhaust gas analysis method has been further developed to specify the traceable molecules in aircraft exhausts, to determine the detection limits, and to obtain reliable statements concerning its accuracy. The first measurement with the Airbus A340 engine CFM56-5C2 during run up tests at ground level showed the overall ability of the FTIR-emission system to analyze the exhausts of modern gas turbines with high bypass ratio and mixing of fan air into the exhausts before the nozzle exit. Good quality spectra were measured and analyzed with respect to the mixing rations of CO2, H2O, CO, NO, and N2O, and the emission indices of CO, NO, and N2O. Total measurement times at one thrust level should be about 15 minutes to obtain reliable result which can be compared to the ICAO data of this engine.

  3. Carbonyl emissions from vehicular exhausts sources in Hong Kong.

    PubMed

    Ho, Steven Sai Hang; Ho, Kin Fai; Lee, Shun Cheng; Cheng, Yan; Yu, Jian Zhen; Lam, Ka Man; Feng, Natale Sin Yau; Huang, Yu

    2012-02-01

    Vehicular emission (VE) is one of the important anthropogenic sources for airborne carbonyls in urban area. Six types of VE-dominated samples were collected at representative locations in Hong Kong where polluted by a particular fueled type of vehicles, including (i) a gas refilling taxis station (liquefied petroleum gas [LPG] emission); (ii) a light-duty passenger car park (gasoline emission); (iii) a minibus station (diesel emission); (iv) a single-deck-bus depot (diesel emission); (v) a double-deck-bus depot (diesel emission); and (vi) a whole-food market entrance for light- and heavy-duty vehicles (diesel emission). A total of 15 carbonyls in the samples were quantified. Formaldehyde was the most abundant carbonyl among the VE-dominated samples, and its contribution to the total quantified amount on a molar basis ranged from 54.8% to 60.8%. Acetaldehyde and acetone were the next two abundant carbonyls. The carbonyls were quantified at three roadside locations in Hong Kong. The highest concentrations of formaldehyde and acetaldehyde, 22.7 +/- 8.4 and 6.0 +/- 2.8 microg/m3, respectively, were determined in the samples collected at a main transportation gate for goods between Hong Kong and Mainland China. The total quantified carbonyl concentration, 37.9 +/- 9.3 microg/m3, was the highest at an entrance of a cross-harbor tunnel in downtown area. The theoretical carbonyls compositions of the three roadside locations were estimated according to the VE-dominated sample profiles and the statistics on vehicle numbers and types during the sampling period. The measured compositions of formaldehyde were much higher than the theoretical compositions in summer, demonstrating that photochemical reactions significantly contributed to the formaldehyde production in the roadsides.

  4. Nanoparticle emissions from 11 non-vehicle exhaust sources - A review

    NASA Astrophysics Data System (ADS)

    Kumar, Prashant; Pirjola, Liisa; Ketzel, Matthias; Harrison, Roy M.

    2013-03-01

    Nanoparticle emissions from road vehicles have been studied extensively in the recent past due to their dominant contribution towards the total airborne particle number concentrations (PNCs) found in the urban atmospheric environment. In view of upcoming tighter vehicle emission standards and adoption of cleaner fuels in many parts of the world, the contribution to urban nanoparticles from non-vehicle exhaust sources (NES) may become more pronounced in future. As of now, only limited information exists on nanoparticle emissions from NES through the discretely published studies. This article presents critically synthesised information in a consolidated manner on 11 NES (i.e. road-tyre interaction, construction and demolition, aircraft, ships, municipal waste incineration, power plants, domestic biomass burning, forest fires, cigarette smoking, cooking, and secondary formation). Source characteristics and formation mechanisms of nanoparticles emitted from each NES are firstly discussed, followed by their emission strengths, airborne concentrations and physicochemical characteristics. Direct comparisons of the strengths of NES are not straightforward but an attempt has been made to discuss their importance relative to the most prominent source (i.e. road vehicles) of urban nanoparticles. Some interesting comparisons emerged such as 1 kg of fast and slow wood burning produces nearly the same number of particles as for each km driven by a heavy duty vehicle (HDV) and a light duty vehicle, respectively. About 1 min of cooking on gas can produce the similar particle numbers generated by ˜10 min of cigarette smoking or 1 m travel by a HDV. Apportioning the contribution of numerous sources from the bulk measured airborne PNCs is essential for determining their relative importance. Receptor modelling methods for estimation of source emission contributions are discussed. A further section evaluates the likely exposure risks, health and regulatory implications associated with

  5. Accuracy of exhaust emission factor measurements on chassis dynamometer.

    PubMed

    Joumard, Robert; Laurikko, Juhani; Le Han, Tuan; Geivanidis, Savas; Samaras, Zissis; Merétei, Tamás; Devaux, Philippe; André, Jean-Marc; Cornelis, Erwin; Lacour, Stéphanie; Prati, Maria Vittoria; Vermeulen, Robin; Zallinger, Michael

    2009-06-01

    To improve the accuracy, reliability, and representativeness of emission factors, 10 European laboratories worked together to study the influence of 20 parameters on the measurement of light-vehicle emission factors on chassis dynamometer of 4 main categories: driving patterns, vehicle-related parameters, vehicle sampling, and laboratory-related parameters. The results are based on (1) literature synthesis, (2) approximately 2700 specific tests with 183 vehicles, and (3) the reprocessing of more than 900 tests. These tests concern the regulated atmospheric pollutants and pre-Euro to Euro 4 vehicles. Of the 20 parameters analyzed, 7 seemed to have no effect, 7 were qualitatively influential, and 6 were highly influential (gearshift strategy, vehicle mileage, ambient temperature, humidity, dilution ratio, and driving cycle). The first four of the six were able to have correction factors developed for them. The results allow for the design of recommendations or guidelines for the emission factor measurement method.

  6. Effect of gasoline composition on stoichiometry and exhaust emissions

    SciTech Connect

    McDonald, C.R.; Lee, G.R.; Otter, G.J. den; Shore, P.R.; Humphries, D.T.

    1994-10-01

    Six full range gasolines were tested in two engines (one with a catalyst) operated at 4 steady states. Engine-out regulated emissions responded to equivalence ratio, {Phi}, in the accepted manner. For both CO and NO{sub x}, there was a characteristic, single emissions response to changes in {Phi}. Changing fuel composition will primarily alter the production of these emissions by modifying the stoichiometric air/fuel ratio, projecting engine operation onto another part of the {Phi} response curve. These {Phi} effects, which are independent of engine design, also determine how operating conditions affect engine-out CO and NO{sub x}. Speciated hydrocarbon measurements at engine-out and tail-pipe confirm results seen in previous test-cycle based programmes. 24 refs., 11 figs., 3 tabs.

  7. General aviation piston-engine exhaust emission reduction

    NASA Technical Reports Server (NTRS)

    Kempke, E. E., Jr.; Houtman, W. H.; Westfield, W. T.; Duke, L. C.; Rezy, B. J.

    1977-01-01

    To support the promulgation of aircraft regulations, two airports were examined, Van Nuys and Tamiami. It was determined that the carbon monoxide (CO) emissions from piston-engine aircraft have a significant influence on the CO levels in the ambient air in and around airports, where workers and travelers would be exposed. Emissions standards were set up for control of emissions from aircraft piston engines manufactured after December 31, 1979. The standards selected were based on a technologically feasible and economically reasonable control of carbon monoxide. It was concluded that substantial CO reductions could be realized if the range of typical fuel-air ratios could be narrowed. Thus, improvements in fuel management were determined as reasonable controls.

  8. Exhaust emissions of DI diesel engine using unconventional fuels

    NASA Astrophysics Data System (ADS)

    Sudrajad, Agung; Ali, Ismail; Hamdan, Hazmie; Hamzah, Mohd. Herzwan

    2012-06-01

    Optimization of using waste plastic and tire disposal fuel on diesel engine were observed. The experimental project was comparison between using both of unconventional fuel and base diesel fuel. The engine experiment was conducted with YANMAR TF120 single cylinder four stroke diesel engine set-up at variable engine speed at 2100, 1900, 1700, 1500 and 1300 rpm. The data have been taken at each point of engine speed during the stabilized engine-operating regime. Measurement of emissions parameters at different engine speed conditions have generally indicated lower in emission COfor waste plastic fuel, lower NOx for tire disposal fuel and lower SOx for diesel fuel.

  9. 40 CFR 90.103 - Exhaust emission standards.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... CO Effective date I 16.1 14.8 610 August 1, 2007; in addition, any Class I engine family initially... regulating emissions of HC, NOX. HC+NOX or NMHC+NOX. as applicable. If the manufacturer exercises the option... volume engine manufacturers as defined in this part may, at their option, certify their engine...

  10. 40 CFR 90.103 - Exhaust emission standards.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... CO Effective date I 16.1 14.8 610 August 1, 2007; in addition, any Class I engine family initially... regulating emissions of HC, NOX. HC+NOX or NMHC+NOX. as applicable. If the manufacturer exercises the option... volume engine manufacturers as defined in this part may, at their option, certify their engine...

  11. 40 CFR 90.103 - Exhaust emission standards.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... CO Effective date I 16.1 14.8 610 August 1, 2007; in addition, any Class I engine family initially... regulating emissions of HC, NOX. HC+NOX or NMHC+NOX. as applicable. If the manufacturer exercises the option... volume engine manufacturers as defined in this part may, at their option, certify their engine...

  12. 40 CFR 86.544-90 - Calculations; exhaust emissions.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... CO2Or of each pollutant (i.e., HC, CO, or NOX) in grams per vehicle kilometer and if appropriate, the weighted carbon mass equivalent of total hydrocarbon equivalent, in grams per vehicle kilometer. (2) Yct = Mass emissions as calculated from the “transient” phase of the cold-start test, in grams per test...

  13. 40 CFR 86.544-90 - Calculations; exhaust emissions.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... CO2Or of each pollutant (i.e., HC, CO, or NOX) in grams per vehicle kilometer and if appropriate, the weighted carbon mass equivalent of total hydrocarbon equivalent, in grams per vehicle kilometer. (2) Yct = Mass emissions as calculated from the “transient” phase of the cold-start test, in grams per test...

  14. 40 CFR 86.544-90 - Calculations; exhaust emissions.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... CO2Or of each pollutant (i.e., HC, CO, or NOX) in grams per vehicle kilometer and if appropriate, the weighted carbon mass equivalent of total hydrocarbon equivalent, in grams per vehicle kilometer. (2) Yct = Mass emissions as calculated from the “transient” phase of the cold-start test, in grams per test...

  15. 40 CFR 86.544-90 - Calculations; exhaust emissions.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... CO2Or of each pollutant (i.e., HC, CO, or NOX) in grams per vehicle kilometer and if appropriate, the weighted carbon mass equivalent of total hydrocarbon equivalent, in grams per vehicle kilometer. (2) Yct = Mass emissions as calculated from the “transient” phase of the cold-start test, in grams per test...

  16. 40 CFR 86.544-90 - Calculations; exhaust emissions.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... CO2Or of each pollutant (i.e., HC, CO, or NOX) in grams per vehicle kilometer and if appropriate, the weighted carbon mass equivalent of total hydrocarbon equivalent, in grams per vehicle kilometer. (2) Yct = Mass emissions as calculated from the “transient” phase of the cold-start test, in grams per test...

  17. 40 CFR 86.1544 - Calculation; idle exhaust emissions.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ...) Emission Regulations for Otto-Cycle Heavy-Duty Engines, New Methanol-Fueled Natural Gas-Fueled, and Liquefied Petroleum Gas-Fueled Diesel-Cycle Heavy-Duty Engines, New Otto-Cycle Light-Duty Trucks, and New Methanol-Fueled Natural Gas-Fueled, and Liquefied Petroleum Gas-Fueled Diesel-Cycle Light-Duty Trucks;...

  18. 40 CFR 86.1544 - Calculation; idle exhaust emissions.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ...) Emission Regulations for Otto-Cycle Heavy-Duty Engines, New Methanol-Fueled Natural Gas-Fueled, and Liquefied Petroleum Gas-Fueled Diesel-Cycle Heavy-Duty Engines, New Otto-Cycle Light-Duty Trucks, and New Methanol-Fueled Natural Gas-Fueled, and Liquefied Petroleum Gas-Fueled Diesel-Cycle Light-Duty Trucks;...

  19. 40 CFR 86.1777-99 - Calculations; exhaust emissions.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... operate on a fuel other than conventional gasoline, including fuel-flexible and dual-fuel vehicles when operated on a fuel other than conventional gasoline, shall be multiplied by the reactivity adjustment factor applicable to the vehicle emission control technology category and fuel. The product of the NMOG...

  20. Analysis on fuel economy improvement and exhaust emission reduction in a two-stroke engine by using an exhaust valve

    SciTech Connect

    Asai, Masahiro; Kurosaki, Takaharu; Okada, Kazunori

    1995-12-31

    A timing controlled auto-ignition name ``AR combustion`` could improve irregular combustion in the part load operation of conventional two-stroke engines. Their previous papers have suggested its idea and the drastic improvements in fuel consumption and HC emission proven through a bench experiments. This time, form a concept that improvements of a two-stroke engine should be done maintaining its original advantages, an AR combustion engine was developed by using a simple exhaust valve and maintaining engine`s original power output. This engine was mounted on a motorcycle and experimented in the ``Dakar rally``. As the results, good fuel economies exceeding a four-stroke rally model, excellent driveability and durability were proven, because of the improvement in the combustion and engine`s potential for the downsizing. The AR combustion engine, consequently, has good prospects for the practical use.

  1. 75 FR 57191 - Compliance With Interstate Motor Carrier Noise Emission Standards: Exhaust Systems

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-09-20

    ... Federal Motor Carrier Safety Administration 49 CFR Part 325 RIN-2126-AB31 Compliance With Interstate Motor Carrier Noise Emission Standards: Exhaust Systems AGENCY: Federal Motor Carrier Safety Administration, DOT... Association (TMA), the Federal Motor Carrier Safety Administration (FMCSA) amends its regulations to eliminate...

  2. 78 FR 65554 - Exhaust Emission Standards for New Aircraft Turbine Engines and Identification Plate for Aircraft...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-11-01

    ... From the Federal Register Online via the Government Publishing Office DEPARTMENT OF TRANSPORTATION Federal Aviation Administration 14 CFR Parts 34 and 45 RIN 2120-AK15 Exhaust Emission Standards for New Aircraft Turbine Engines and Identification Plate for Aircraft Engines Correction In rule document 2013-24712, appearing on pages 63015-63017 in...

  3. Introduction to NASA contracts. [on engine modifications to reduce exhaust emissions

    NASA Technical Reports Server (NTRS)

    Kempke, E. E., Jr.

    1976-01-01

    The NASA Lewis Research Center issued requests for proposal to Avco Lycoming and Teledyne Continental Motors for a contractual effort to establish and demonstrate engine modifications to reduce exhaust emissions safely with minimum adverse effects on cost, weight, and fuel economy. The secondary objective was reducing fuel consumption.

  4. 40 CFR 91.103 - Averaging, banking, and trading of exhaust emission credits.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 20 2010-07-01 2010-07-01 false Averaging, banking, and trading of... Standards and Certification Provisions § 91.103 Averaging, banking, and trading of exhaust emission credits. Regulations regarding averaging, banking, and trading provisions along with applicable...

  5. 40 CFR 1066.831 - Exhaust emission test procedures for aggressive driving.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... aggressive driving. 1066.831 Section 1066.831 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Vehicles § 1066.831 Exhaust emission test procedures for aggressive driving. (a) This section describes how to test using the US06 or LA-92 driving schedule. The US06 driving schedule can be divided into...

  6. 40 CFR 1045.101 - What exhaust emission standards and requirements must my engines meet?

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 32 2010-07-01 2010-07-01 false What exhaust emission standards and requirements must my engines meet? 1045.101 Section 1045.101 Protection of Environment ENVIRONMENTAL PROTECTION... engines must meet the requirements in § 1045.115. (b) It is important that you read § 1045.145...

  7. 40 CFR 1037.241 - Demonstrating compliance with exhaust emission standards for greenhouse gas pollutants.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 34 2013-07-01 2013-07-01 false Demonstrating compliance with exhaust emission standards for greenhouse gas pollutants. 1037.241 Section 1037.241 Protection of Environment... standards for greenhouse gas pollutants. (a) For purposes of certification, your vehicle family...

  8. 40 CFR 1037.241 - Demonstrating compliance with exhaust emission standards for greenhouse gas pollutants.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 33 2014-07-01 2014-07-01 false Demonstrating compliance with exhaust emission standards for greenhouse gas pollutants. 1037.241 Section 1037.241 Protection of Environment... standards for greenhouse gas pollutants. (a) For purposes of certification, your vehicle family...

  9. 40 CFR 1037.241 - Demonstrating compliance with exhaust emission standards for greenhouse gas pollutants.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 34 2012-07-01 2012-07-01 false Demonstrating compliance with exhaust emission standards for greenhouse gas pollutants. 1037.241 Section 1037.241 Protection of Environment... standards for greenhouse gas pollutants. (a) For purposes of certification, your vehicle family...

  10. External fins and ejector action for reducing the infrared emission of engine exhaust ducting

    NASA Technical Reports Server (NTRS)

    Vanfossen, G. J., Jr.

    1975-01-01

    An analytical investigation was conducted to determine the feasibility of using external fins and ejector action on the exhaust ducting of a helicopter to reduce the infrared emission of the aircraft. Temperatures were calculated for both circular disk fins and pin fins. Results show that combining ejector action with fins can lower the metal temperature to acceptable levels at least for high flight speeds.

  11. Exhaust and evaporative emissions from motorcycles fueled with ethanol gasoline blends.

    PubMed

    Li, Lan; Ge, Yunshan; Wang, Mingda; Peng, Zihang; Song, Yanan; Zhang, Liwei; Yuan, Wanli

    2015-01-01

    The emission characteristics of motorcycles using gasoline and E10 (90% gasoline and 10% ethanol by volume) were investigated in this article. Exhaust and evaporative emissions of three motorcycles were investigated on the chassis dynamometer over the Urban Driving Cycle (UDC) and in the Sealed Housing for Evaporative Determination (SHED) including regulated and unregulated emissions. The regulated emissions were detected by an exhaust gas analyzer directly. The unregulated emissions including carbonyls and volatile organic compounds (VOCs) were sampled through battery-operated air pumps using tubes coated with 2,4-dinitrophenylhydrazine (DNPH) and Tenax TA, respectively. The experimental results showed that the emission factors of total hydrocarbons (THC) and carbon monoxide (CO) from E10 fueling motorcycles decreased by 26%-45% and 63%-73%, while the emission factor of NOx increased by 36%-54% compared with those from gasoline fueling motorcycles. For unregulated emissions, the emission amount of VOCs from motorcycles fueled with E10 decreased by 18%-31% while total carbonyls were 2.6-4.5 times higher than those for gasoline. For evaporative emissions of THC and VOCs, for gasoline or E10, the diurnal breathing loss (DBL) was higher than hot soak loss (HSL). Using E10 as a fuel does not make much difference in the amount of evaporative THC, while resulted in a slightly growth of 14%-17% for evaporative BETX (benzene, toluene, ethylbenzene, xylene). Copyright © 2014 Elsevier B.V. All rights reserved.

  12. Parametric modeling of exhaust gas emission from natural gas fired gas turbines

    SciTech Connect

    Bakken, L.E.; Skogly, L.

    1996-07-01

    Increased focus on air pollution from gas turbines in the Norwegian sector of the North Sea has resulted in taxes on CO{sub 2}. Statements made by the Norwegian authorities imply regulations and/or taxes on NO{sub x} emissions in the near future. The existing CO{sub 2} tax of NOK 0.82/Sm{sup 3} (US Dollars 0.12/Sm{sup 3}) and possible future tax on NO{sub x} are analyzed mainly with respect to operating and maintenance costs for the gas turbine. Depending on actual tax levels, the machine should be operated on full load/optimum thermal efficiency or part load to reduce specific exhaust emissions. Based on field measurements, exhaust emissions (CO{sub 2}, CO, NO{sub x}, N{sub 2}O, UHC, etc.) are established with respect to load and gas turbine performance, including performance degradation. Different NO{sub x} emission correlations are analyzed based on test results, and a proposed prediction model presented. The impact of machinery performance degradation on emission levels is particularly analyzed. Good agreement is achieved between measured and predicted NO{sub x} emissions from the proposed correlation. To achieve continuous exhaust emission control, the proposed NO{sub x} model is implemented to the on-line condition monitoring system on the Sleipner A platform, rather than introducing sensitive emission sensors in the exhaust gas stack. The on-line condition monitoring system forms an important tool in detecting machinery condition/degradation and air pollution, and achieving optimum energy conservation.

  13. 40 CFR 1045.240 - How do I demonstrate that my engine family complies with exhaust emission standards?

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... deterioration factor for exhaust emissions. For engines that do not use aftertreatment technology, use an... deterioration factor for exhaust emissions. For engines that use aftertreatment technology, such as catalytic... each pollutant and then add the results before rounding. (e) Use good engineering judgment to...

  14. 40 CFR 600.114-08 - Vehicle-specific 5-cycle fuel economy and carbon-related exhaust emission calculations.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... Model Year Automobiles-Test Procedures § 600.114-08 Vehicle-specific 5-cycle fuel economy and carbon... to calculate 5-cycle carbon-related exhaust emissions values for the purpose of determining optional... each vehicle tested, determine the 5-cycle city carbon-related exhaust emissions using the...

  15. 40 CFR 600.510-12 - Calculation of average fuel economy and average carbon-related exhaust emissions.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 30 2014-07-01 2014-07-01 false Calculation of average fuel economy and average carbon-related exhaust emissions. 600.510-12 Section 600.510-12 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) ENERGY POLICY FUEL ECONOMY AND GREENHOUSE GAS EXHAUST EMISSIONS...

  16. 40 CFR 87.21 - Standards for exhaust emissions.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 31, 1999. Oxides of Nitrogen: (40 + 2(rPR)) grams/kilonewtons rO. (iv) Engines of a type or model of... Nitrogen: (32 + 1.6(rPR)) grams/kilonewtons rO. (v) The emission standards prescribed in paragraphs (d)(1... greater than 89 kilonewtons: Oxides of Nitrogen: (19 + 1.6(rPR)) grams/kilonewtons rO. (2) Engines with...

  17. 14 CFR 34.21 - Standards for exhaust emissions.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... individual engine was on or before December 31, 1999: Oxides of Nitrogen: (40+2(rPR)) grams/kilonewtons r0... after December 31, 1999: Oxides of Nitrogen: (32+1.6 (rPR)) grams/kilonewtons r0. (v) The emission... 89 kilonewtons: Oxides of Nitrogen: (19 + 1.6 (rPR)) grams/kilonewtons rO. (B) That have a...

  18. 14 CFR 34.21 - Standards for exhaust emissions.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... individual engine was on or before December 31, 1999: Oxides of Nitrogen: (40+2(rPR)) grams/kilonewtons r0... after December 31, 1999: Oxides of Nitrogen: (32+1.6 (rPR)) grams/kilonewtons r0. (v) The emission... 89 kilonewtons: Oxides of Nitrogen: (19 + 1.6 (rPR)) grams/kilonewtons rO. (B) That have a...

  19. Effect of ethanol-gasoline blends on small engine generator energy efficiency and exhaust emission.

    PubMed

    Lin, Wen-Yinn; Chang, Yuan-Yi; Hsieh, You-Ru

    2010-02-01

    This study was focused on fuel energy efficiency and pollution analysis of different ratios of ethanol-gasoline blended fuels (E0, E3, E6, and E9) under different loadings. In this research, the experimental system consisted of a small engine generator, a particulate matter measurement system, and an exhaust gas analyzer system. Different fuels, unleaded gasoline, and ethanol-gasoline blends (E0, E3, E6, and E9) were used to study their effects on the exhaust gas emission and were expressed as thermal efficiency of the small engine generator energy efficiency. The results suggested that particle number concentration increased as the engine loading increased; however, it decreased as the ethanol content in the blend increased. While using E6 as fuel, the carbon monoxide (CO) concentration was less than other fuels (E0, E3, and E9) for each engine loading. The average of CO concentration reduction by using E3, E6, and E9 is 42, 86, and 83%, respectively. Using an ethanol-gasoline blend led to a significant reduction in exhaust emissions by approximately 78.7, 97.5, and 89.46% of the mean average values of hydrocarbons (HCs) with E3, E6, and E9 fuels, respectively, for all engine loadings. Using an ethanol-gasoline blend led to a significant reduction in exhaust emissions by approximately 35, 86, and 77% of the mean average values of nitrogen oxides (NOx) with E3, E6, and E9 fuels, respectively, at each engine loading. The E6 fuel gave the best results of the exhaust emissions, and the E9 fuel gave the best results of the particle emissions and engine performance. The thermal efficiency of the small engine generator increased as the ethanol content in the blend increased and as the engine loading increased.

  20. Quantification of vehicle fleet PM10 particulate matter emission factors from exhaust and non-exhaust sources using tunnel measurement techniques.

    PubMed

    Lawrence, Samantha; Sokhi, Ranjeet; Ravindra, Khaiwal

    2016-03-01

    Road tunnels act like large laboratories; they provide an excellent environment to quantify atmospheric particles emission factors from exhaust and non-exhaust sources due to their known boundary conditions. Current work compares the High Volume, Dichotomous Stacked Filter Unit and Partisol Air Sampler for coarse, PM10 and PM2.5 particle concentration measurement and found that they do not differ significantly (p = 95%). PM2.5 fraction contributes 66% of PM10 proportions and significantly influenced by traffic (turbulence) and meteorological conditions. Mass emission factors for PM10 varies from 21.3 ± 1.9 to 28.8 ± 3.4 mg/vkm and composed of Motorcycle (0.0003-0.001 mg/vkm), Cars (26.1-33.4 mg/vkm), LDVs (2.4-3.0 mg/vkm), HDVs (2.2-2.8 mg/vkm) and Buses (0.1 mg/vkm). Based on Lawrence et al. (2013), source apportionment modelling, the PM10 emission of brake wear (3.8-4.4 mg/vkm), petrol exhaust (3.9-4.5 mg/vkm), diesel exhaust (7.2-8.3 mg/vkm), re-suspension (9-10.4 mg/vkm), road surface wear (3.9-4.5 mg/vkm), and unexplained (7.2 mg/vkm) were also calculated. The current study determined that the combined non-exhaust fleet PM10 emission factor (16.7-19.3 mg/vkm) are higher than the combined exhaust emission factor (11.1-12.8 mg/vkm). Thus, highlight the significance of non-exhaust emissions and the need for legislation and abatement strategies to reduce their contributions to ambient PM concentrations.

  1. Combustion Performance and Exhaust Emission of DI Diesel Engine Using Various Sources of Waste Cooking Oil

    NASA Astrophysics Data System (ADS)

    Afiq, Mohd; Azuhairi, Mohd; Jazair, Wira

    2010-06-01

    In Malaysia, more than 200-tone of cooking oil are used by domestic users everyday. After frying process, about a quarter of these cooking oil was remained and drained into sewage system. This will pollutes waterways and affects the ecosystem. The use of waste cooking oil (WCO) for producing bio-diesel was considered in economical factor which current production cost of bio-diesel production is higher in Malaysia due to higher price of palm oil. Thus, the aim of this study is to investigate the most suitable source of WCO to become a main source of bio-diesel for bio-diesel production in this country. To perform this research, three type of WCO were obtained from house's kitchen, cafeteria and mamak's restaurant. In this study, prospect of these bio-diesel source was evaluated based on its combustion performance and exhaust emissions operated in diesel engine in the form of waste cooking oil methyl ester (WCOME) and have been compared with pure diesel fuel. A 0.6 liter, single-cylinder, air-cooled direct injection diesel engine was used to perform this experiment. Experiment was done at variable engine loads and constant engine speed. As the result, among three stated WCOMEs, the one collected from house's kitchen gives the best performance in term of brake specific fuel consumption (bsfc) and brake power (BP) with lowest soot emission.

  2. Effectiveness of non-noble metal based diesel oxidation catalysts on particle number emissions from diesel and biodiesel exhaust.

    PubMed

    Shukla, Pravesh Chandra; Gupta, Tarun; Labhasetwar, Nitin Kumar; Khobaragade, Rohini; Gupta, Neeraj K; Agarwal, Avinash Kumar

    2017-01-01

    Two new formulations of non-noble metal based diesel oxidation catalysts based on CoCe based mixed oxide (DOC2) and perovskite catalysts (DOC3) were prepared and retrofitted in a 4-cylinder diesel engine fueled by diesel and Karanja biodiesel blend (KB20). In this study, their effectiveness in reducing raw exhaust particulate emissions vis-à-vis a commercial diesel oxidation catalyst (DOC1) was evaluated. Emission characteristics such as particle number-size distribution, mass-size distribution, and surface area-size distribution, total particle number concentration and count mean diameter as a function of engine load at constant engine speed were evaluated. Variations in total particle number concentration as a function of engine speed were also determined. The prepared DOCs and the commercial DOC showed varying degrees of performance as a function of engine operating conditions. Overall, effectiveness of the prepared DOC's appeared to be more fuel specific. For diesel exhaust, overall performance of DOC1 was more effective compared to both prepared DOCs, with DOC2 being superior to DOC3. In case of KB20 exhaust, the overall performance of DOC2 was either more effective or nearly comparable to DOC1, while DOC3 being not so effective. This showed that the DOCs based on CoCe based mixed oxide catalysts have potential to replace commercial noble metal based DOC's, especially in engines fueled by biodiesel. Copyright © 2016 Elsevier B.V. All rights reserved.

  3. Estimation of exhaust and non-exhaust gaseous, particulate matter and air toxics emissions from on-road vehicles in Delhi

    NASA Astrophysics Data System (ADS)

    Nagpure, Ajay Singh; Gurjar, B. R.; Kumar, Vivek; Kumar, Prashant

    2016-02-01

    Analysis of emissions from on-road vehicles in an Indian megacity, Delhi, have been performed by comparing exhaust emissions of gaseous, particulate matter and mobile source air toxics (MSATs), together with volatile organic compound (VOCs) and PM10 (particulate matter ≤10 μm) from non-exhaust vehicular sources, during the past (1991-2011) and future (2011-2020) scenarios. Results indicate that emissions of most of the pollutants from private vehicles (two wheelers and cars) have increased by 2- to 18-times in 2020 over the 1991 levels. Two wheelers found to be dominating the emissions of carbon monoxide (CO, 29-51%), hydrocarbons (HC, 45-73%), acetaldehyde (46-51%) and total poly aromatic hydrocarbons (PAHs, 37-42%). Conversely, private cars were found to be responsible for the majority of the carbon dioxide (CO2, 24-42%), 1,3-butadiene (72-89%), benzene (60-82%), formaldehyde (23-44%) and total aldehyde (27-52%) between 1991 and 2011. The heavy-duty commercial vehicles (HCVs) shows their accountability for most of the nitrogen oxide (NOx, 18-41%) and PM10 (33-43%) emissions during the years 1991-2011. In terms of PM10 emissions, vehicular exhaust contributed by 21-55%, followed by road dust (42-73%) and brake wear (3-5%) between 1991 and 2011. After 2002, non-exhaust emissions (e.g. road dust, brake wear and tyre wear) together indicate higher accountability (66-86%) for PM10 emission than the exhaust emissions (14-34%). The temporal trend of emissions of NOx and CO show reasonable agreement with available ambient air concentrations that were monitored at locations, significantly influenced by vehicular activity. Encouraging results were emerged, showing a good correlation coefficient for CO (0.94) and NOx (0.68).

  4. Catalytic converters for exhaust emission control of commercial equipment powered by internal combustion engines.

    PubMed Central

    Cohn, J G

    1975-01-01

    The development of PTX, monolithic catalytic exhaust purifiers, is outlined, and their first use for exhaust emissions control of commercial equipment is described. The main use of PTX converters is on forklift trucks. The purification achievable with PTX-equipped fork-lift trucks under various operational conditions is discussed, and examples from the field are given. During more than ten years of operation, no adverse health effects have been reported, and PTX-equipped internal combustion engines appear safe for use in confined areas. PMID:50933

  5. Correction of Measured Taxicab Exhaust Emission Data Based on Cmem Modle

    NASA Astrophysics Data System (ADS)

    Li, Q.; Jia, T.

    2017-09-01

    Carbon dioxide emissions from urban road traffic mainly come from automobile exhaust. However, the carbon dioxide emissions obtained by the instruments are unreliable due to time delay error. In order to improve the reliability of data, we propose a method to correct the measured vehicles' carbon dioxide emissions from instrument based on the CMEM model. Firstly, the synthetic time series of carbon dioxide emissions are simulated by CMEM model and GPS velocity data. Then, taking the simulation data as the control group, the time delay error of the measured carbon dioxide emissions can be estimated by the asynchronous correlation analysis, and the outliers can be automatically identified and corrected using the principle of DTW algorithm. Taking the taxi trajectory data of Wuhan as an example, the results show that (1) the correlation coefficient between the measured data and the control group data can be improved from 0.52 to 0.59 by mitigating the systematic time delay error. Furthermore, by adjusting the outliers which account for 4.73 % of the total data, the correlation coefficient can raise to 0.63, which suggests strong correlation. The construction of low carbon traffic has become the focus of the local government. In order to respond to the slogan of energy saving and emission reduction, the distribution of carbon emissions from motor vehicle exhaust emission was studied. So our corrected data can be used to make further air quality analysis.

  6. Research Approach for Aging and Evaluating Diesel Exhaust catalysts

    SciTech Connect

    Wayne, Scott

    2000-08-20

    To determine the impact of diesel fuel sulfur levels on emissions control devices that could lower emissions of oxides of nitrogen (NOX) and particulate matter (PM) from on-highway trucks and buses in the 2002-2004 model years. West Virginia University is evaluating: - Diesel Oxidation Catalysts - Lean NOX Catalysts

  7. Effect of some Turkish vegetable oil-diesel fuel blends on exhaust emissions

    SciTech Connect

    Ergeneman, M.; Oezaktas, T.; Cigizoglu, K.B.; Karaosmanoglu, F.; Arslan, E.

    1997-10-01

    For different types of vegetable oils of Turkish origin (sunflower, corn, soybean, and olive oil) were blended with grade No. 2-D diesel fuel at a ratio of 20/80 (v/v). The effect of the compression ratio on exhaust emissions is investigated in an American Society for Testing and Materials (ASTM)-cooperative fuel research (CFR) engine working with the mentioned fuel blends and a baseline diesel fuel. A decrease in soot, CO, CO{sub 2}, and HC emissions and an increase in NO{sub x} emissions have been observed for fuel blends compared to diesel fuel.

  8. Effects of equivalence ratio and dwell time on exhaust emissions from an experimental premixing prevaporizing burner

    NASA Technical Reports Server (NTRS)

    Anderson, D.

    1974-01-01

    A flame-tube study was performed to determine the effects of equivalence ratio and residence time on exhaust emissions with premixed, prevaporized propane fuel. Nitrogen oxides emissions as low as .3 g NO2/kg fuel were measured with greater than 99% combustion efficiency at 800 K inlet temperature and an equivalence ratio of .4. For a constant combustion efficiency, lower nitrogen oxides emissions were obtained by burning very lean with relatively long residence times than by using somewhat higher equivalence ratios with shorter times.

  9. Estimation of road vehicle exhaust emissions from 1992 to 2010 and comparison with air quality measurements in Genoa, Italy

    NASA Astrophysics Data System (ADS)

    Zamboni, Giorgio; Capobianco, Massimo; Daminelli, Enrico

    An investigation into road transport exhaust emissions in the Genoa urban area was performed by comparing the quantities of carbon monoxide (CO), nitrogen oxides (NO x), nitrogen dioxide (NO 2) and particulate matter (PM) emitted by different vehicle categories with air quality measurements referred to the same pollutants. Exhaust emissions were evaluated by applying the PROGRESS (computer PROGramme for Road vehicle EmiSSions evaluation) code, developed by the Internal Combustion Engines Group of the University of Genoa, to eight different years (from 1992 to 2010), considering spark ignition and Diesel passenger cars and light duty vehicles, heavy duty vehicles and buses, motorcycles and mopeds. Changes in terms of vehicles number, mileage and total emissions are presented together with relative distributions among the various vehicle categories. By comparing 1992 and 2010 data, calculated trends show a 7% increase in the number of vehicles, with total mileage growing at a faster rate (approx. 22%); total emissions decrease considerably, by approximately 50% for NO x and PM, 70% for HC and 80% for CO, due to improvements in engines and fuels forced by the stricter European legislation and the fleet renewal, while primary NO 2 emission will be very close to 1992 level, after a decrease of about 18% in 2000. Air quality was analysed by selecting traffic and background measuring stations from the monitoring network managed by the Environmental Department of the Province of Genoa: average annual concentrations of considered pollutants from 1994 to 2007 were calculated in order to obtain the relative historical trends and compare them with European public health limits and with road vehicle emissions. Though an important reduction in pollutant concentrations has been achieved as a consequence of cleaner vehicles, some difficulties in complying with present and/or future NO 2 and PM 10 limits are also apparent, thus requiring suitable measures to be taken by the local

  10. Assessment of benzene and toluene emissions from automobile exhaust in Bangkok.

    PubMed

    Muttamara, S; Leong, S T; Lertvisansak, I

    1999-07-01

    The use of unleaded gasoline, together with an increase in the number of vehicles in Bangkok, has significantly influenced benzene and toluene concentrations in vehicular emissions and contributes to the air pollution problem. As a matter of practical necessity, a quick test program is done for the measurement of emission concentrations/rates for vehicles driven on the road. Exhaust emission measurement at idle mode was conducted in a fleet of 12 vehicles of different model years and manufacturers. The study revealed that the benzene and toluene concentrations in the exhaust effluent averaged 4.4-22.02 and 12.24-44.75 mg/m3, respectively for 1990-1992 cars and decreased to 0.76-4.14 and 0.89-6.26 mg/m3, respectively for 1994-1995 cars. In another study, exhaust emission measurement on a chassis dynamometer was carried out in a fleet of nine selected, in-use cars. It was observed that benzene and toluene emission rates were considerably higher-in the range of 70.84-85.82 and 354.15- 429.00 mg/km, respectively, for 1990-1991 model year cars. Lower benzene and toluene emission rates of 0.43-95.07 and 2. 15-475.35 mg/km, respectively, were represented by newer cars with model years 1994-1995. These results indicated that there was a significant increase in benzene and toluene emission concentrations and rates with increasing car mileage and model year. The finding also revealed that only 28% of the tested vehicles complied to the approved emission standard.

  11. Characterization, concentrations and emission rates of polycyclic aromatic hydrocarbons in the exhaust emissions from in-service vehicles in Damascus

    NASA Astrophysics Data System (ADS)

    Alkurdi, Farouk; Karabet, François; Dimashki, Marwan

    2013-02-01

    Motor vehicles are significant sources of polycyclic aromatic hydrocarbon (PAH) emissions to the urban atmosphere. Improved understanding of PAH emission profiles in mobile sources is the key to determining the viable approach for reducing PAH emissions from motor vehicles. Very limited data is available on the levels of PAH emissions in the urban atmospheres in Syria and no data are currently available on the level of PAH emissions from different combustion sources in the country. The aim of this study was to determine the profile and concentration of PAH in exhaust emissions of light and heavy-duty vehicles running on the roads of Damascus city. Three different types of vehicles (passenger cars, minivans and buses) were selected along with different age groups. Vapor- and particulate-phase PAH were collected from the vehicular exhausts of six in-service vehicles (with/without catalytic converters). High-performance liquid chromatography system, equipped with UV-Visible and fluorescence detectors, was used for the identification and quantification of PAH compounds in the cleaned extracts of the collected samples. The mean concentration of total PAH emissions (sum of 15 compounds) from all types of studied vehicles ranged between 69.28 ± 1.06 μg/m3 for passenger cars equipped with catalytic converters and 2169.41 ± 5.17 μg/m3 for old diesel buses without pollution controls. Values of total benzo(a)pyrene equivalent (∑ B[a]Peq) ranged between 1.868 μg/m3and 37.652 μg/m3. The results obtained in this study showed that the use of catalytic converters resulted into cleaner exhaust compositions and emissions with characteristics that are distinct from those obtained in the absence of catalytic converters.

  12. Toward reconciling instantaneous roadside measurements of light duty vehicle exhaust emissions with type approval driving cycles.

    PubMed

    Rhys-Tyler, Glyn A; Bell, Margaret C

    2012-10-02

    A method is proposed to relate essentially instantaneous roadside measurements of vehicle exhaust emissions, with emission results generated over a type approval driving cycle. An urban remote sensing data set collected in 2008 is used to define the dynamic relationship between vehicle specific power and exhaust emissions, across a range of vehicle ages, engine capacities, and fuel types. The New European Driving Cycle is synthesized from the remote sensing data using vehicle specific power to characterize engine load, and the results compared with official published emissions data from vehicle type approval tests over the same driving cycle. Mean carbon monoxide emissions from gasoline-powered cars ≤ 3 years old measured using remote sensing are found to be 1.3 times higher than published original type approval test values; this factor increases to 2.2 for cars 4-8 years old, and 6.4 for cars 9-12 years old. The corresponding factors for diesel cars are 1.1, 1.4, and 1.2, respectively. Results for nitric oxide, hydrocarbons, and particulate matter are also reported. The findings have potential implications for the design of traffic management interventions aimed at reducing emissions, fleet inspection and maintenance programs, and the specification of vehicle emission models.

  13. Comparison of exhaust emissions resulting from cold- and hot-start motorcycle driving modes.

    PubMed

    Yao, Yung-Chen; Tsai, Jiun-Horng; Ye, Hui-Fen; Chiang, Hung-Lung

    2009-11-01

    This study investigated the emissions of criteria air pollutants (carbon monoxide [CO], hydrocarbons [HCs], and oxides of nitrogen [NOx]) from motorcycle exhaust at cold- and hot-start driving cycles on a chassis dynamometer. Seven four-stroke carburetors and two fuel-injection motorcycles were tested. As expected, the emission factors (g/km) of CO and HCs increased during cold-start driving. The ratio of emission factors (g/km) for cold- and hot-start driving cycles ranged from 1.1-1.5 (for CO) to 1.2-2.8 (for HCs). However, the difference of NOx emissions between the cold- and hot-start cycles was not pronounced. Further, the cold-/hot-start ratios of CO and HCs from 50-cm3 motorcycles were higher than those of 100- and 125-cm3 motorcycles; however, the carbon dioxide (CO2) emission was the lowest for the four-stroke motorcycles. High engine temperature and poor combustion efficiency of smaller cylinder-capacity motorcycles may contribute a significant amount of exhaust emission. Additionally, the fuel-base emission factor (g/L-fuel) ratios were low compared with the distance-base emission factor (g/km) in cold- and hot-start driving. This indicates that the effect of catalyst efficiency was greater than the effect of fuel combustion in the tested motorcycles. A comparison of emission ratios of motorcycles and passenger cars shows that the warm-up may be more important for cars, especially under low-temperature conditions. However, the motorcycle contributes a large proportion of CO and HC emissions in many Asian counties. The difference between cold- and hot-start emissions may affect inventory

  14. 40 CFR 600.206-12 - Calculation and use of FTP-based and HFET-based fuel economy and carbon-related exhaust emission...

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... HFET-based fuel economy and carbon-related exhaust emission values for vehicle configurations. 600.206... POLICY FUEL ECONOMY AND CARBON-RELATED EXHAUST EMISSIONS OF MOTOR VEHICLES Procedures for Calculating Fuel Economy and Carbon-Related Exhaust Emission Values for 1977 and Later Model Year Automobiles §...

  15. 40 CFR 600.208-12 - Calculation of FTP-based and HFET-based fuel economy and carbon-related exhaust emission values...

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ...-based fuel economy and carbon-related exhaust emission values for a model type. 600.208-12 Section 600... ECONOMY AND CARBON-RELATED EXHAUST EMISSIONS OF MOTOR VEHICLES Procedures for Calculating Fuel Economy and Carbon-Related Exhaust Emission Values for 1977 and Later Model Year Automobiles § 600.208-12 Calculation...

  16. Particle-Bound PAH Emission from the Exhaust of Combustion Chamber

    NASA Astrophysics Data System (ADS)

    Asgari Lamjiri, M.; Medrano, Y. S.; Guillaume, D. W.; Khachikian, C. S.

    2013-12-01

    Polycyclic Aromatic Hydrocarbons (PAHs) are harmful, semi-volatile organic compounds which are generated due to the incomplete combustion of organic substances. PAHs are of concern as a pollutant because some of these compounds are carcinogenic and mutagenic even at low levels. Most of the PAHs are recalcitrant and persistent in the environment. The PAHs carcinogenic potential can be increased by the adsorption onto small size particles (< 1μm) which can easily get into the bronchioles and alveoli of the lungs. PAHs associated with sub-micron particles are mostly generated from high temperature sources like combustion chambers. In this current study, the presence of 16 priority PAHs (listed by United States Environmental Protection Agency) which are attached to the particulates emitted from the exhaust of the jet engine are evaluated. The engine was operated at different swirl numbers (S; the ratio of tangential air flow to axial air flow) to investigate the effect of this parameter on the effluent of combustion chamber. The samples were collected using two instruments simultaneously: a particle analyzer and a Micro-Orifice Uniform Deposited Impactor (MOUDI). Particle analyzer was used to count the number of particles in different sizes and MOUDI was used to collect particles with respect to their size as they were emitted from the exhaust. The MOUDI's aluminum substrates were weighed before and after the experiment in order to measure the mass of particles that were collected during the sampling period. The concentration of PAHs associated with the particles was measured by extracting the particles with dichloromethane followed by analysis via gas chromatography/mass spectrometry (GC/MS). In general, lower molecular weight PAHs emitted from the exhaust of combustion chamber are mostly in gas phase while PAHs of higher molecular weight are adsorbed onto particles. Preliminary results from GC/MS confirm the presence of higher molecular weight PAHs like Benzo

  17. Exhaust Emissions from Gasoline- and LPG-Powered Vehicles Operating at the Altitude of Mexico City.

    PubMed

    Gamas, Erick D; Diaz, Luis; Rodriguez, René; López-Salinas, E; Schifter, Isaac; Ontiveros, Luis

    1999-10-01

    Unburned hydrocarbons (HCs), carbon monoxide (CO), and oxides of nitrogen (NOx) are the compounds regulated as pollutants by an environmental standard in the Metropolitan Area of Mexico City (MAMC). The main fuel used in vehicular transportation is gasoline, and the use of liquefied petroleum gas (LPG) is now an alternative as low emission technology to decrease the environmental impact of transportation operations. The environmental impact of commercial gasoline consumption in the Valley of Mexico was estimated by on-road and FTP-75 testing of three formulations of gasoline (one leaded [octane 81] and two unleaded [one octane 87 and one octane 93]). A fleet of 30 vehicles was used: 10 were chosen that had pre-1990 technology, while 12 were 1991-1996 vehicles equipped with fuel injection, catalytic converters, and air/ fuel ratio control technology. The remaining eight vehicles were high-performance new model vehicles (1995-1996) equipped with the newest technology available for pollution control. Fifteen vehicles in the fleet were also tested for the effect of changing from leaded to unleaded gasoline. Three different LPG formulations were tested using three vehicles representative of the LPG-powered fleet in the MAMC. Two gasoline-to-LPG conversion certified commercial systems were evaluated following the BAR-90 and the HOT-505 procedures. Emissions corresponding to the high-octane (premium) gasoline showed a 15% higher contribution to HCs with a 6% lower reactivity than the 87 octane gasoline; the HCs in the exhaust for premium gasoline are mainly isoparaffins. When the vehicles were tested on the road at high speeds, an average 3% increase in mileage was obtained when vehicles were switched from leaded to unleaded gasoline, while a 5% increase in mileage was observed when vehicles were switched from 87 octane to premium gasoline. The tests of LPG formulations indicated that a change in composition from 60% vol of propane to 85.5% vol reduces levels of HCs and

  18. A study on exhaust gas emissions from ships in Turkish Straits

    NASA Astrophysics Data System (ADS)

    Kesgin, Ugur; Vardar, Nurten

    The Turkish Straits, i.e. Istanbul (Bosphorus) and Canakkale (Dardanellen), which connect Black Sea and Aegean Sea, have a continuously increasing maritime traffic. Especially, the maritime traffic on Bosphorus (Istanbul Strait) that connects the continents of Europe and Asia is too complex due to geographical conditions. The maritime traffic in the Turkish Straits includes the ships, which are in use in domestic transport, the transit passing ships with various aims and fishing, sport or strolling ships. In this paper, fuel consumption and exhaust gas emissions NO x, CO, CO 2, VOC, PM exhausted from ships such as transit vessels, which are passing both Bosphorus and Dardanellen, and passenger ships used in domestic transport on the Bosphorus are calculated. In order to do this the general characteristics, the main engine systems, the fuel types, cruising times and speeds of all vessels are taken into consideration. The calculated NO x emissions on the Bosphorus are 2720 t from domestic passenger ships and 4357 t from transit ships. In this case it is clear that the transit ships cause more than half of the total amount of emissions from ships on the Bosphorus. The amount of nitrogen oxide emissions from domestic passenger ships used for public transport in Istanbul Strait is equal to approx. 4% of nitrogen oxide emissions from motor vehicles in Istanbul. Finally, the future emissions from ships in Turkish Straits are discussed.

  19. Experimental Evaluation of Installed Cooking Exhaust Fan Performance

    SciTech Connect

    Singer, Brett C.; Delp, William W.; Apte, Michael G.

    2010-11-01

    The installed performance of cooking exhaust fans was evaluated through residential field experiments conducted on a sample of 15 devices varying in design and other characteristics. The sample included two rear downdraft systems, two under-cabinet microwave over range (MOR) units, three different installations of an under-cabinet model with grease screens across the bottom and no capture hood, two devices with grease screens covering the bottom of a large capture hood (one under-cabinet, one wall-mount chimney), four under-cabinet open hoods, and two open hoods with chimney mounts over islands. Performance assessment included measurement of airflow and sound levels across fan settings and experiments to quantify the contemporaneous capture efficiency for the exhaust generated by natural gas cooking burners.Capture efficiency is defined as the fraction of generated pollutants that are removed through the exhaust and thus not available for inhalation of household occupants. Capture efficiency (CE) was assessed for various configurations of burner use (e.g., single front, single back, combination of one front and one back, oven) and fan speed setting. Measured airflow rates were substantially lower than the levels noted in product literature for many of the units. This shortfall was observed for several units costing in excess of $1000. Capture efficiency varied widely (from<5percent to roughly 100percent) across devices and across conditions for some devices. As expected, higher capture efficiencies were achieved with higher fan settings and the associated higher air flow rates. In most cases, capture efficiencies were substantially higher for rear burners than for front burners. The best and most consistent performance was observed for open hoods that covered all cooktop burners and operated at higher airflow rates. The lowest capture efficiencies were measured when a front burner was used with a rear backdraft system or with lowest fan setting for above the range

  20. From Contrails and Smoke Trails to Exhaust Particle Processes: A Brief History of Aircraft Particulate Emissions

    DTIC Science & Technology

    2011-12-01

    2,6- Dimethylnaphthalene Acenaphthylene Acenaphthene Phenanthrene Anthracene Fluoranthene Benz[ a ]anthracene Benzofluoranthenes Benzo [ a ] pyrene Indeno...1,2,3-c,d] pyrene Benzo [g,h,i]perylene Methane Ethane Propane Acetylene Propene n-Pentane n-Hexane Toluene n-Decane Dodecane Tridecane Formaldehyd e...Aerodyne Research, Inc. From Contrails and Smoke Trails to Exhaust Particle Processes: A brief history of aircraft particulate emissions Presented

  1. Suppression of Thermal Emission from Exhaust Components Using an Integrated Approach

    DTIC Science & Technology

    2002-08-01

    Thick Film Cooling; Thin Film Cooling; Fin cooling; Hidden Sacrifice Surface using Coanda Effect; View hiding with insulation; Emissivity Control Plume...system while using a hidden surface to stabilize the flow and the Coanda effect to turn the flow in a desired direction at the exit plane. When view...34* Simple Exhaust using Coanda Effect to direct flow away from the vehicle; "* Segmentation into multiple jets to test self absorption; "* Vortex

  2. Physical Sciences Facility Air Emission Control Equivalency Evaluation

    SciTech Connect

    Brown, David M.; Belew, Shan T.

    2008-10-17

    This document presents the adequacy evaluation for the application of technology standards during design, fabrication, installation and testing of radioactive air exhaust systems at the Physical Sciences Facility (PSF), located on the Horn Rapids Triangle north of the Pacific Northwest National Laboratory (PNNL) complex. The analysis specifically covers the exhaust portion of the heating, ventilation and air conditioning (HVAC) systems associated with emission units EP-3410-01-S, EP-3420-01-S and EP 3430-01-S.

  3. Application of hybrid evolutionary algorithms to low exhaust emission diesel engine design

    NASA Astrophysics Data System (ADS)

    Jeong, S.; Obayashi, S.; Minemura, Y.

    2008-01-01

    A hybrid evolutionary algorithm, consisting of a genetic algorithm (GA) and particle swarm optimization (PSO), is proposed. Generally, GAs maintain diverse solutions of good quality in multi-objective problems, while PSO shows fast convergence to the optimum solution. By coupling these algorithms, GA will compensate for the low diversity of PSO, while PSO will compensate for the high computational costs of GA. The hybrid algorithm was validated using standard test functions. The results showed that the hybrid algorithm has better performance than either a pure GA or pure PSO. The method was applied to an engineering design problem—the geometry of diesel engine combustion chamber reducing exhaust emissions such as NOx, soot and CO was optimized. The results demonstrated the usefulness of the present method to this engineering design problem. To identify the relation between exhaust emissions and combustion chamber geometry, data mining was performed with a self-organising map (SOM). The results indicate that the volume near the lower central part of the combustion chamber has a large effect on exhaust emissions and the optimum chamber geometry will vary depending on fuel injection angle.

  4. Turbine engine exhaust gas measurements using in-situ FT-IR emission/transmission spectroscopy

    NASA Astrophysics Data System (ADS)

    Marran, David F.; Cosgrove, Joseph E.; Neira, Jorge; Markham, James R.; Rutka, Ronald; Strange, Richard R.

    2001-02-01

    12 An advanced multiple gas analyzer based on in-situ Fourier transform infrared spectroscopy has been used to successfully measure the exhaust plume composition and temperature of an operating gas turbine engine at a jet engine test stand. The sensor, which was optically coupled to the test cell using novel broadband hollow glass waveguides, performed well in this harsh environment (high acoustical noise and vibration, considerable temperature swings in the ambient with engine operation), providing quantitative gas phase information. Measurements were made through the diameter of the engine's one meter exhaust plume, about 0.7 meters downstream of the engine exit plane. The sensor performed near simultaneous infrared transmission and infrared emission measurements through the centerline of the plume. Automated analysis of the emission and transmission spectra provided the temperature and concentration information needed for engine tuning and control that will ensure optimal engine operation and reduced emissions. As a demonstration of the utility and accuracy of the technique, carbon monoxide, nitric oxide, water, and carbon dioxide were quantified in spite of significant variations in the exhaust gas temperature. At some conditions, unburned fuel, particulates (soot/fuel droplets), methane, ethylene and aldehydes were identified, but not yet quantified.

  5. The effects of acceleration rate on vehicle exhaust emissions and fuel economy. Technical report

    SciTech Connect

    Landman, L.C.

    1982-08-01

    This report summarizes a test program which was designed to explore the impact on exhaust emissions and fuel economy of coupling the dynamometer rollers (front and rear) and of using acceleration rates higher than those used on the Federal Test Procedure (FTP). A total of six vehicles were tested in this program. All five gasoline-fueled exhibited increases in hydrocarbons (HC) and carbon monoxide (CO) emissions on the Federal Test Procedure (FTP) driving cycle when the dynamometer rollers were coupled. The other results are strongly vehicle dependent.

  6. Gaseous exhaust emissions from a J-58 engine at simulated supersonic flight conditions

    NASA Technical Reports Server (NTRS)

    Holdeman, J. D.

    1974-01-01

    Emissions of total oxides of nitrogen, unburned hydrocarbons, carbon monoxide, and carbon dioxide from a J-58 engine at simulated flight conditions of Mach 2.0, 2.4, and 2.8 at 19.8 km altitude are reported. For each flight condition, measurements were made for four engine power levels from maximum power without afterburning through maximum afterburning. These measurements were made 7 cm downstream of the engine primary nozzle using a single point traversing gas sample probe. Results show that emissions vary with flight speed, engine power level, and with radial position across the exhaust.

  7. A comparison of exhaust emissions from vehicles fuelled with petrol, LPG and CNG

    NASA Astrophysics Data System (ADS)

    Bielaczyc, P.; Szczotka, A.; Woodburn, J.

    2016-09-01

    This paper presents an analysis of THC, NMHC, CO, NOx and CO2 emissions during testing of two bi-fuel vehicles, fuelled with petrol and gaseous fuels, on a chassis dynamometer in the context of the Euro 6 emissions requirements. The analyses were performed on one Euro 5 bi-fuel vehicle (petrol/LPG) and one Euro 5 bi-fuel vehicle (petrol/CNG), both with SI engines equipped with MPI feeding systems operating in closed-loop control, typical three-way-catalysts and heated oxygen sensors. The vehicles had been adapted by their manufacturers for fuelling with LPG or CNG by using additional special equipment mounted onto the existing petrol fuelling system. The vehicles tested featured multipoint gas injection systems. The aim of this paper was an analysis of the impact of the gaseous fuels on the exhaust emission in comparison to the emission of the vehicles fuelled with petrol. The tests subject to the analyses presented here were performed in the Engine Research Department of BOSMAL Automotive Research and Development Institute Ltd in Bielsko-Biala, Poland, within a research programme investigating the influence of alternative fuels on exhaust emissions from light duty vehicle vehicles with spark-ignition and compression-ignition engines.

  8. Compensation of the exhaust gas transport dynamics for accurate instantaneous emission measurements.

    PubMed

    Ajtay, Delia; Weilenmann, Martin

    2004-10-01

    Instantaneous emission models of vehicles describe the amount of emitted pollutants as a function of the driving state of the car. Emission measurements of chassis dynamometer tests with high time resolution are necessary for the development of such models. However, the dynamics of gas transport in both the exhaust system of the car and the measurement line last significantly longer than 1 s. In a simplified approach, the transport dynamics can be divided into two parts: a perfect time delay, corresponding to a piston-like transport of the exhaust gas, and a dynamic part, corresponding to the mixing of gases by turbulence along the way. This determines the occurrence of emission peaks that are longer in time and lower in height at the analyzer than they actually are in the vehicle at their location of formation. It is shown here how the sharp emission signals at their location of formation can be reconstructed from the flattened emission signals recorded at the analyzer by using signal theory approaches. A comparison between the reconstructions quality when using the raw or the dilution analyzer system is also given.

  9. Emissions in the exhaust of fishing boats after adding viscous agents into fuel oils.

    PubMed

    Hsieh, Lien-Te; Shih, Shun-I; Lin, Sheng-Lun; Yang, Tsun-Lirng; Wu, Tser-Son; Hung, Chung-Hsien

    2009-12-20

    In order to avoid the illegal use of fishing boat fuel A (FBFA) by traveling diesel vehicles (TDVs) in Taiwan, alternatives that are easily distinguished from premium diesel fuel (PDF) were prepared to evaluate their suitability. Two new ingredients, pyrolysis fuel oil (PFO) and residue of desulfurization unit (RDS), were added into FBFA and formed PFO0.5 and RDS0.5, respectively. Along with FBFA, these three fuels were analyzed for their chemical and physical properties. Furthermore, they were used by three fishing boats with different sizes, output powers, and weights. The engine performances and pollutant emissions were examined and monitored. Experimental results show that there are significant differences in appearance between PDF and the two new blended fuels (PFO0.5 and RDS0.5), and thus misuse or illegal use of FBFA could be substantially reduced. The fuel consumption, which is negatively related to the heating value of fuels, is in order of FBFAemissions, while the PM emission factors (g bhp(-1) h(-1) and g L(-1)-fuel) were reduced by approximately 36% and 33%, respectively. Owing to the higher total aromatic content in PFO0.5 and RDS0.5, total-PAH concentrations in the exhausts from the three fishing boats using PFO0.5 and RDS0.5 were slightly (1.2 and 1.1 times, respectively) higher than for those using FBFA. Nevertheless, the estimated total BaP(eq) from the three fishing boats using RDS0.5 was 27.5, 19.5, and 8.25% lower than those using FBFA. With using PFO0.5, they were totally different, at 23.5, 2.79, and 2.58% higher. With regard to looking different to PDF, RDS0.5 is superior to PFO0.5, and is thus recommended as a better alternative to FBFA, particularly because it can help lower more emissions of CO, NO(x), PM and BaP(eq).

  10. Characterization of polycyclic aromatic hydrocarbons and carbonyl compounds in diesel exhaust emissions.

    PubMed

    Mabilia, Rosanna; Cecinato, Angelo; Tomasi Scianò, Maria Concetta; Di Palo, Vincenzo; Possanzini, Massimiliano

    2004-01-01

    Exhaust emissions from a recent model heavy-duty diesel vehicle (city bus) in a chassis dynamometer were measured during a transient driving cycle. Particle-bound polycyclic aromatic hydrocarbons (PAHs) and gaseous carbonyls, substances that create health hazards and are, as yet, unregulated were collected, the former on filters and the latter on dinitrophenylhydrazine (DNPH)-coated silica cartridges and analysed by GC-MS and HPLC, respectively. PAH emission rates decreased with the number of benzene fused rings. They averaged 0.2 mg km(-1) for a total of 11 PAHs ranging from fluoranthene to benzo(ghi)perylene. Fluoranthene and pyrene accounted for 90% of total PAHs. The sum of emission rates of C1 approximately C6 carbonyls averaged 174 mg km(-1), even if formaldehyde alone represented approximately 70% of the total carbonyl mass, followed by acetaldehyde (13%). Results obtained were compared with emission data reported in previous studies.

  11. Performance and Exhaust Emissions in a Natural-Gas Fueled Dual-Fuel Engine

    NASA Astrophysics Data System (ADS)

    Shioji, Masahiro; Ishiyama, Takuji; Ikegami, Makoto; Mitani, Shinichi; Shibata, Hiroaki

    In order to establish the optimum fueling in a natural gas fueled dual fuel engine, experiments were done for some operational parameters on the engine performances and the exhaust emissions. The results show that the pilot fuel quantity should be increased and its injection timing should be advanced to suppress unburned hydrocarbon emission in the middle and low output range, while the quantity should be reduced and the timing retarded to avoid onset of knock at high loads. Unburned hydrocarbon emission and thermal efficiency are improved by avoiding too lean natural gas mixture by restricting intake charge air. However, the improvement is limited because the ignition of pilot fuel deteriorates with excessive throttling. It is concluded that an adequate combination of throttle control and equivalence ratio ensures low hydrocarbon emission and the thermal efficiency comparable to diesel operation.

  12. On-road measurement of particle emission in the exhaust plume of a diesel passenger car.

    PubMed

    Vogt, Rainer; Scheer, Volker; Casati, Roberto; Benter, Thorsten

    2003-09-15

    Particle size distributions were measured under real world dilution conditions in the exhaust plume of a diesel passenger car closely followed by a mobile laboratory on a high speed test track. Under carefully controlled conditions the exhaust plume was continuously sampled and analyzed inside the mobile laboratory. Exhaust particle size distribution data were recorded together with exhaust gas concentrations, i.e., CO, CO2, and NO(x), and compared to data obtained from the same vehicle tested on a chassis dynamometer. Good agreement was found for the soot mode particles which occurred at a geometric mean diameter of approximately 50 nm and a total particle emission rate of 10(14) particles km(-1). Using 350 ppm high sulfur fuel and the standard oxidation catalyst a bimodal size distribution with a nucleation mode at 10 nm was observed at car velocities of 100 km h(-1) and 120 km h(-1), respectively. Nucleation mode particles were only present if high sulfur fuel was used with the oxidation catalyst installed. This is in agreement with prior work that these particles are of semivolatile nature and originate from the nucleation of sulfates formed inside the catalyst. Temporal effects of the occurrence of nucleation mode particles during steady-state cruising and the dynamical behavior during acceleration and deceleration were investigated.

  13. Primary particulate emissions and secondary organic aerosol (SOA) formation from idling diesel vehicle exhaust in China.

    PubMed

    Deng, Wei; Hu, Qihou; Liu, Tengyu; Wang, Xinming; Zhang, Yanli; Song, Wei; Sun, Yele; Bi, Xinhui; Yu, Jianzhen; Yang, Weiqiang; Huang, Xinyu; Zhang, Zhou; Huang, Zhonghui; He, Quanfu; Mellouki, Abdelwahid; George, Christian

    2017-09-01

    In China diesel vehicles dominate the primary emission of particulate matters from on-road vehicles, and they might also contribute substantially to the formation of secondary organic aerosols (SOA). In this study tailpipe exhaust of three typical in-use diesel vehicles under warm idling conditions was introduced directly into an indoor smog chamber with a 30m(3) Teflon reactor to characterize primary emissions and SOA formation during photo-oxidation. The emission factors of primary organic aerosol (POA) and black carbon (BC) for the three types of Chinese diesel vehicles ranged 0.18-0.91 and 0.15-0.51gkg-fuel(-1), respectively; and the SOA production factors ranged 0.50-1.8gkg-fuel(-1) and SOA/POA ratios ranged 0.7-3.7 with an average of 2.2. The fuel-based POA emission factors and SOA production factors from this study for idling diesel vehicle exhaust were 1-3 orders of magnitude higher than those reported in previous studies for idling gasoline vehicle exhaust. The emission factors for total particle numbers were 0.65-4.0×10(15)particleskg-fuel(-1), and particles with diameters less than 50nm dominated in total particle numbers. Traditional C2-C12 precursor non-methane hydrocarbons (NMHCs) could only explain less than 3% of the SOA formed during aging and contribution from other precursors including intermediate volatile organic compounds (IVOC) needs further investigation. Copyright © 2017 Elsevier B.V. All rights reserved.

  14. 40 CFR 1054.235 - What exhaust emission testing must I perform for my application for a certificate of conformity?

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... each type of fuel for which you intend to certify the engine. In the case of flexible-fuel engines..., SMALL NONROAD SPARK-IGNITION ENGINES AND EQUIPMENT Certifying Emission Families § 1054.235 What exhaust... accumulation before emission testing. (a) Select an emission-data engine from each engine family for testing as...

  15. 40 CFR 1054.235 - What exhaust emission testing must I perform for my application for a certificate of conformity?

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... each type of fuel for which you intend to certify the engine. In the case of flexible-fuel engines..., SMALL NONROAD SPARK-IGNITION ENGINES AND EQUIPMENT Certifying Emission Families § 1054.235 What exhaust... accumulation before emission testing. (a) Select an emission-data engine from each engine family for testing as...

  16. Engine exhaust characteristics evaluation in support of aircraft acoustic testing

    NASA Astrophysics Data System (ADS)

    Ennix, Kimberly A.

    1994-02-01

    NASA Dryden Flight Research Facility and NASA Langley Research Center completed a joint acoustic flight test program. Test objectives were (1) to quantify and evaluate subsonic climb-to-cruise noise and (2) to obtain a quality noise database for use in validating the Aircraft Noise Prediction Program. These tests were conducted using aircraft with engines that represent the high nozzle pressure ratio of future transport designs. Test flights were completed at subsonic speeds that exceeded Mach 0.3 using F-18 and F-16XL aircraft. This paper describes the efforts of NASA Dryden Flight Research Facility in this flight test program. Topics discussed include the test aircraft, setup, and matrix. In addition, the engine modeling codes and nozzle exhaust characteristics are described.

  17. Engine exhaust characteristics evaluation in support of aircraft acoustic testing

    NASA Technical Reports Server (NTRS)

    Ennix, Kimberly A.

    1994-01-01

    NASA Dryden Flight Research Facility and NASA Langley Research Center completed a joint acoustic flight test program. Test objectives were (1) to quantify and evaluate subsonic climb-to-cruise noise and (2) to obtain a quality noise database for use in validating the Aircraft Noise Prediction Program. These tests were conducted using aircraft with engines that represent the high nozzle pressure ratio of future transport designs. Test flights were completed at subsonic speeds that exceeded Mach 0.3 using F-18 and F-16XL aircraft. This paper describes the efforts of NASA Dryden Flight Research Facility in this flight test program. Topics discussed include the test aircraft, setup, and matrix. In addition, the engine modeling codes and nozzle exhaust characteristics are described.

  18. Engine exhaust characteristics evaluation in support of aircraft acoustic testing

    NASA Technical Reports Server (NTRS)

    Ennix, Kimberly A.

    1993-01-01

    NASA Dryden Flight Research Facility and NASA Langley Research Center completed a joint acoustic flight test program. Test objectives were (1) to quantify and evaluate subsonic climb-to-cruise noise and (2) to obtain a quality noise database for use in validating the Aircraft Noise Prediction Program. These tests were conducted using aircraft with engines that represent the high nozzle pressure ratio of future transport designs. Test flights were completed at subsonic speeds that exceeded Mach 0.3 using F-18 and F-16XL aircraft. This paper describes the efforts of NASA Dryden Flight Research Facility in this flight test program. Topics discussed include the test aircraft, setup, and matrix. In addition, the engine modeling codes and nozzle exhaust characteristics are described.

  19. Research on the 2nd generation biofuel BIOXDIESEL in aspects of emission of toxic substances in exhaust gases

    NASA Astrophysics Data System (ADS)

    Struś, M. S.; Poprawski, W.; Rewolte, M.

    2016-09-01

    This paper presents results of research of Diesel engines emission of toxic substances in exhaust gases fuelled with a second generation biofuel BIOXDIESEL, which is a blend of Fatty Acid Ethyl Esters obtained from waste resources such waste vegetable and animal fats, bioethanol and standard Diesel fuel. Presented results are very promising, showing that the emission of toxic substances in exhaust gases are significantly reduced when fuelling with BIOXDIESEL fuel in comparison with standard Diesel fuel.

  20. Studies on exhaust emissions of catalytic coated spark ignition engine with adulterated gasoline.

    PubMed

    Muralikrishna, M V S; Kishor, K; Venkata Ramana Reddy, Ch

    2006-04-01

    Adulteration of automotive fuels, especially, gasoline with cheaper fuels is widespread throughout south Asia. Some adulterants decrease the performance and life of the engine and increase the emission of harmful pollutants causing environmental and health problems. The present investigation is carried out to study the exhaust emissions from a single cylinder spark ignition (SI) engine with kerosene blended gasoline with different versions of the engine, such as conventional engine and catalytic coated engine with different proportions of the kerosene ranging from 0% to 40% by volume in steps of 10% in the kerosene-gasoline blend. The catalytic coated engine used in the study has copper coating of thickness 400 microns on piston and inner surface of the cylinder head. The pollutants in the exhaust, carbon monoxide (CO) and unburnt hydrocarbons (UBHC) are measured with Netel Chromatograph CO and HC analyzer at peak load operation of the engine. The engine is provided with catalytic converter with sponge iron as a catalyst to control the pollutants from the exhaust of the engine. An air injection is also provided to the catalytic converter to further reduce the pollutants. The pollutants found to increase drastically with adulterated gasoline. Copper-coated engine with catalytic converter significantly reduced pollutants, when compared to conventional engine.

  1. Accounting for exhaust gas transport dynamics in instantaneous emission models via smooth transition regression.

    PubMed

    Kamarianakis, Yiannis; Gao, H Oliver

    2010-02-15

    Collecting and analyzing high frequency emission measurements has become very usual during the past decade as significantly more information with respect to formation conditions can be collected than from regulated bag measurements. A challenging issue for researchers is the accurate time-alignment between tailpipe measurements and engine operating variables. An alignment procedure should take into account both the reaction time of the analyzers and the dynamics of gas transport in the exhaust and measurement systems. This paper discusses a statistical modeling framework that compensates for variable exhaust transport delay while relating tailpipe measurements with engine operating covariates. Specifically it is shown that some variants of the smooth transition regression model allow for transport delays that vary smoothly as functions of the exhaust flow rate. These functions are characterized by a pair of coefficients that can be estimated via a least-squares procedure. The proposed models can be adapted to encompass inherent nonlinearities that were implicit in previous instantaneous emissions modeling efforts. This article describes the methodology and presents an illustrative application which uses data collected from a diesel bus under real-world driving conditions.

  2. Dilution rates for tailpipe emissions: effects of vehicle shape, tailpipe position, and exhaust velocity.

    PubMed

    Chang, Victor W C; Hildemann, Lynn M; Chang, Cheng-hisn

    2009-06-01

    The rate at which motor vehicle exhaust undergoes dilution with ambient air will greatly affect the size distribution characteristics of the particulate emissions. Wind tunnel experiments were conducted to investigate the impacts of vehicle shape, tailpipe orientation, and exhaust exit velocity on the dilution profiles under steady driving conditions for three model vehicles: a light-duty truck, a passenger car, and a heavy-duty tractor head. A three dimensional array of 60 sensors provided simultaneous measurements of dilution ratios for the emissions in the near- and far-wake regions downstream of the vehicle. The processes underlying the observations were investigated via nondimensionalization. Many of the trends seen substantially downstream can be well generalized using a simple nondimensionalization technique; however, this is not true in the near-wake region (within a downstream distance equivalent to a few vehicle heights). In the near-wake region, using the vehicle width and length to normalize for the vehicle shape is not enough to fully account for the variations seen. Including the exhaust flow rate in the nondimensionalization process is effective further downwind but does not adequately capture the complexity in the near-wake region. Tailpipe orientation and location are also shown to be influential factors affecting the near-wake dilution characteristics.

  3. Exhaust emission calibration of two J-58 afterburning turbojet engines at simulated high-altitude, supersonic flight conditions

    NASA Technical Reports Server (NTRS)

    Holdeman, J. D.

    1976-01-01

    Emissions of total oxides of nitrogen, nitric oxide, unburned hydrocarbons, carbon monoxide, and carbon dioxide from two J-58 afterburning turbojet engines at simulated high-altitude flight conditions are reported. Test conditions included flight speeds from Mach 2 to 3 at altitudes from 16.0 to 23.5 km. For each flight condition exhaust measurements were made for four or five power levels, from maximum power without afterburning through maximum afterburning. The data show that exhaust emissions vary with flight speed, altitude, power level, and radial position across the exhaust. Oxides of nitrogen emissions decreased with increasing altitude and increased with increasing flight speed. Oxides of nitrogen emission indices with afterburning were less than half the value without afterburning. Carbon monoxide and hydrocarbon emissions increased with increasing altitude and decreased with increasing flight speed. Emissions of these species were substantially higher with afterburning than without.

  4. Gaseous exhaust emissions from a JT8D-109 turbofan engine at simulated cruise flight conditions

    NASA Technical Reports Server (NTRS)

    Diehl, L. A.; Holdeman, J. D.

    1975-01-01

    Gaseous emissions from a JT8D-109 turbofan engine were measured in an altitude facility at four simulated cruise flight conditions: Mach 0.8 at altitudes of 9.1, 10, 7, and 12.2 km and Mach 0.9 at 10.7 km. Engine inlet air temperature was held constant at 283 K for all tests. Emissions measurements were made at nominally 6 cm intervals across the horizontal diameter of the engine exhaust nozzle with a single-point traversing gas sample probe. Measured emissions of decreased with increasing altitude from an emission index of 10.4 to one of 8.3, while carbon monoxide increased with increasing altitude from an emission index of 1.6 to one of 4.4. Unburned hydrocarbon emissions were essentially negligible for all flight conditions. Since the engine inlet air temperatures were not correctly simulated, the NOx emission indices were corrected to true altitude conditions by using correlating parameters for changes in combustor inlet temperature, pressure, and temperature rise. The correction was small at the lowest altitude. At the 10.7 and 12.2 km, Mach 0.8 test conditions the correction decreased the measured values by 1 emission index.

  5. Studies of diesel engine particle emissions during transient operations using an Engine Exhaust Particle Sizer

    SciTech Connect

    Wang, Jian; Storey, John Morse; Domingo, Norberto; Huff, Shean P; Thomas, John F; West, Brian H; Lee, Doh-Won

    2006-01-01

    Diesel engine particle emissions during transient operations, including emissions during FTP transient cycles and during active regenerations of a NOx adsorber, were studied using a fast Engine Exhaust Particle Sizer (EEPS). For both fuels tested, a No. 2 certification diesel and a low sulfur diesel (BP-15), high particle concentrations and emission rates were mainly associated with heavy engine acceleration, high speed, and high torque during transient cycles. Averaged over the FTP transient cycle, the particle number concentration during tests with the certification fuel was 1.2e8/cm3, about four times the particle number concentration observed during tests using the BP-15 fuel. The effect of each engine parameter on particle emissions was studied. During tests using BP-15, the particle number emission rate was mainly controlled by the engine speed and torque, whereas for Certification fuel, the engine acceleration also had a strong effect on number emission rates. The effects of active regenerations of a diesel NOx adsorber on particle emissions were also characterized for two catalyst regeneration strategies: Delayed Extended Main (DEM) and Post 80 injection (Post80). Particle volume concentrations observed during DEM regenerations were much higher than those during Post80 regenerations, and the minimum air to fuel ratio achieved during the regenerations had little effect on particle emission for both strategies. This study provides valuable information for developing strategies that minimize the particle formation during active regenerations of NOx adsorbers.

  6. Characteristics of volatile organic compounds from motorcycle exhaust emission during real-world driving

    NASA Astrophysics Data System (ADS)

    Tsai, Jiun-Horng; Huang, Pei-Hsiu; Chiang, Hung-Lung

    2014-12-01

    The number of motorcycles has increased significantly in Asia, Africa, Latin American and Europe in recent years due to their reasonable price, high mobility and low fuel consumption. However, motorcycles can emit significant amounts of air pollutants; therefore, the emission characteristics of motorcycles are an important consideration for the implementation of control measures for motorcycles in urban areas. Results of this study indicate that most volatile organic compound (VOC) emission factors were in the range of several decades mg/km during on-road driving. Toluene, isopentane, 1,2,4-trimethylbenzene, m,p-xylene, and o-xylene were the most abundant VOCs in motorcycle exhaust, with emission factors of hundreds mg/km. Motorcycle exhaust was 15.4 mg/km for 15 carbonyl species. Acetaldehyde, acetone, formaldehyde and benzaldehyde were the major carbonyl species, and their emission factors ranged from 1.4 to 3.5 mg/km 1,2,4-trimethylbenzene, m,p-xylene, 1-butene, toluene, o-xylene, 1,2,3-trimethylbenzene, propene, 1,3,5-trimethylbenzene, isoprene, m-diethylbenzene, and m-ethyltoluene were the main ozone formation potential (OFP) species, and their OFP was 200 mg-O3/km or higher.

  7. Design of the NDUV detection circuit for the NO concentration of the vehicle exhaust emissions

    NASA Astrophysics Data System (ADS)

    Zhang, Kai; Zhang, Yujun; He, Ying; You, Kun; Gao, Yanwei; Chen, Chen; Liu, Guohua; He, Chungui; Lu, Yibing; Liu, Wenqing

    2016-10-01

    With the increasing number of vehicles, the harm from NO to the environment becomes more and more prominent. So the monitoring of the NO concentration of the vehicle exhaust emissions is very important to assess the emission levels. In this paper, the NO detection system designing for vehicle exhaust emissions based on the non-dispersive ultraviolet principle (NDUV) has been researched. The technical indexes of the two-way modulation UV signal detection circuit are discussed in detail. And then a precision detection circuit is designed, which is composed of a trans-impedance amplifier and a lock-in amplifier, with which the output of the UV photoelectric detector can be amplified to a suitable voltage range, and the DC noise of the pre-stage amplifier is effectively removed by the lock-in amplifier. An experimental system was set up to test the designed circuit. To ensure the consistency of the two channels, the method of exchange calibration was adopted in the test. It's drawn that the designed circuit is of high SNR, measuring accuracy and a large dynamic range from the test results. The NO concentration detection limit of vehicle emissions can reach 1ppm, and the detection precision is +/-15ppm.

  8. Influence of driving cycles on exhaust emissions and fuel consumption of gasoline passenger car in Bangkok.

    PubMed

    Nutramon, Tamsanya; Supachart, Chungpaibulpatana

    2009-01-01

    The influence of different driving cycles on their exhaust emissions and fuel consumption rate of gasoline passenger car was investigated in Bangkok based on the actual measurements obtained from a test vehicle driving on a standard chassis dynamometer. A newly established Bangkok driving cycle (BDC) and the European driving cycle (EDC) which is presently adopted as the legislative cycle for testing automobiles registered in Thailand were used. The newly developed BDC is constructed using the driving characteristic data obtained from the real on-road driving tests along selected traffic routes. A method for selecting appropriate road routes for real driving tests is also introduced. Variations of keyed driving parameters of BDC with different driving cycles were discussed. The results showed that the HC and CO emission factors of BDC are almost two and four times greater than those of EDC, respectively. Although the difference in the NOx emission factor is small, the value from BDC is still greater than that of EDC by 10%. Under BDC, the test vehicle consumes fuel about 25% more than it does under EDC. All these differences are mainly attributed to the greater proportion of idle periods and higher fluctuations of vehicle speed in the BDC cycle. This result indicated that the exhausted emissions and fuel consumption of vehicles obtained from tests under the legislative modal-type driving cycle (EDC) are significantly different from those actually produced under real traffic conditions especially during peak periods.

  9. Evaluation of Mobile Source Emissions and Trends

    NASA Astrophysics Data System (ADS)

    Dallmann, Timothy Ryan

    Mobile sources contribute significantly to air pollution problems. Relevant pollutants include numerous gaseous and particle-phase species that can affect human health, ecosystems, and climate. Accurate inventories of emissions from these sources are needed to help understand possible adverse impacts, and to develop effective air quality management strategies. Unfortunately large uncertainties persist in the understanding of mobile source emissions, and how these emissions are changing over time. This dissertation aims to evaluate long-term trends in mobile source emissions in the United States, and to make detailed measurements of emissions from present-day fleets of on-road vehicles operating in California. Long-term trends in mobile source emissions of nitrogen oxides (NO x) and fine particulate matter (PM2.5) in the United States were investigated through development of a fuel-based emission inventory. Annual emissions from on- and off-road gasoline and diesel engines were quantified for the years 1996-2006. Diesel engines were found to be the dominant mobile source of NOx and PM2.5, and on-road diesel vehicles were identified as the single largest anthropogenic source of NOx emissions in the United States as of 2005. The importance of diesel engines as a source of exhaust particulate matter emissions has led to the recent introduction of advanced emission control technologies in the United States, such as diesel particle filters (DPF), which have been required since 2007 for all new on-road heavy-duty (HD) diesel engines. In addition to national requirements for the use of such control devices on new engines, California has mandated accelerated clean-up of statewide emissions from older in-use diesel engines. The plume capture method was further applied to measure emissions from a more diverse population of trucks observed at the Caldecott tunnel in summer 2010. Emissions from hundreds of individual trucks were measured, and emission factor distributions were

  10. Evaporative and exhaust emissions from cars fueled with gasoline containing ethanol or methyl tert-butyl ether

    SciTech Connect

    Furey, R.L.; King, J.B.

    1980-01-01

    Vehicle tests showed that evaporative emissions were increased significantly by adding 10% ethanol to gasoline, but were increased less with 15% MTBE in gasoline. The quantity of ethanol or MTBE in evaporative emissions was investigated in laboratory tests. Exhaust HC, CO, and NO/sub x/ emissions from a car without closed-loop fuel control were significantly lower with the ethanol and MTBE fuel blends than with gasoline. For cars equipped with closed-loop carburetors, the absolute differences in exhaust emissions among the fuels were small. Fuel economy and driveability were worse with ethanol and MTBE fuel blends than with gasoline.

  11. Impact of higher alcohols blended in gasoline on light-duty vehicle exhaust emissions.

    PubMed

    Ratcliff, Matthew A; Luecke, Jon; Williams, Aaron; Christensen, Earl; Yanowitz, Janet; Reek, Aaron; McCormick, Robert L

    2013-12-03

    Certification gasoline was splash blended with alcohols to produce four blends: ethanol (16 vol%), n-butanol (17 vol%), i-butanol (21 vol%), and an i-butanol (12 vol%)/ethanol (7 vol%) mixture; these fuels were tested in a 2009 Honda Odyssey (a Tier 2 Bin 5 vehicle) over triplicate LA92 cycles. Emissions of oxides of nitrogen, carbon monoxide, non-methane organic gases (NMOG), unburned alcohols, carbonyls, and C1-C8 hydrocarbons (particularly 1,3-butadiene and benzene) were determined. Large, statistically significant fuel effects on regulated emissions were a 29% reduction in CO from E16 and a 60% increase in formaldehyde emissions from i-butanol, compared to certification gasoline. Ethanol produced the highest unburned alcohol emissions of 1.38 mg/mile ethanol, while butanols produced much lower unburned alcohol emissions (0.17 mg/mile n-butanol, and 0.30 mg/mile i-butanol); these reductions were offset by higher emissions of carbonyls. Formaldehyde, acetaldehyde, and butyraldehyde were the most significant carbonyls from the n-butanol blend, while formaldehyde, acetone, and 2-methylpropanal were the most significant from the i-butanol blend. The 12% i-butanol/7% ethanol blend was designed to produce no increase in gasoline vapor pressure. This fuel's exhaust emissions contained the lowest total oxygenates among the alcohol blends and the lowest NMOG of all fuels tested.

  12. 40 CFR 600.208-12 - Calculation of FTP-based and HFET-based fuel economy, CO2 emissions, and carbon-related exhaust...

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... or diesel test fuel. (ii) Calculate the city, highway, and combined fuel economy, CO2 emissions, and...-based fuel economy, CO2 emissions, and carbon-related exhaust emissions for a model type. 600.208-12... FUEL ECONOMY AND GREENHOUSE GAS EXHAUST EMISSIONS OF MOTOR VEHICLES Procedures for Calculating...

  13. 40 CFR 600.208-12 - Calculation of FTP-based and HFET-based fuel economy, CO2 emissions, and carbon-related exhaust...

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... or diesel test fuel. (ii) Calculate the city, highway, and combined fuel economy, CO2 emissions, and...-based fuel economy, CO2 emissions, and carbon-related exhaust emissions for a model type. 600.208-12... FUEL ECONOMY AND GREENHOUSE GAS EXHAUST EMISSIONS OF MOTOR VEHICLES Procedures for Calculating...

  14. 40 CFR 600.208-12 - Calculation of FTP-based and HFET-based fuel economy, CO2 emissions, and carbon-related exhaust...

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... or diesel test fuel. (ii) Calculate the city, highway, and combined fuel economy, CO2 emissions, and...-based fuel economy, CO2 emissions, and carbon-related exhaust emissions for a model type. 600.208-12... FUEL ECONOMY AND GREENHOUSE GAS EXHAUST EMISSIONS OF MOTOR VEHICLES Procedures for Calculating...

  15. 40 CFR 600.113-12 - Fuel economy, CO2 emissions, and carbon-related exhaust emission calculations for FTP, HFET, US06...

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ...) ENERGY POLICY FUEL ECONOMY AND GREENHOUSE GAS EXHAUST EMISSIONS OF MOTOR VEHICLES Fuel Economy and Carbon... the non-zero value for CREE for purposes of meeting the greenhouse gas emission standards described in... electricity greenhouse gas emission rate at the powerplant, in grams per watt-hour). 2478 is the...

  16. Experimental investigation on performance and exhaust emissions of castor oil biodiesel from a diesel engine.

    PubMed

    Shojaeefard, M H; Etgahni, M M; Meisami, F; Barari, A

    2013-01-01

    Biodiesel, produced from plant and animal oils, is an important alternative to fossil fuels because, apart from dwindling supply, the latter are a major source of air pollution. In this investigation, effects of castor oil biodiesel blends have been examined on diesel engine performance and emissions. After producing castor methyl ester by the transesterification method and measuring its characteristics, the experiments were performed on a four cylinder, turbocharged, direct injection, diesel engine. Engine performance (power, torque, brake specific fuel consumption and thermal efficiency) and exhaust emissions were analysed at various engine speeds. All the tests were done under 75% full load. Furthermore, the volumetric blending ratios of biodiesel with conventional diesel fuel were set at 5, 10, 15, 20 and 30%. The results indicate that lower blends of biodiesel provide acceptable engine performance and even improve it. Meanwhile, exhaust emissions are much decreased. Finally, a 15% blend of castor oil-biodiesel was picked as the optimized blend of biodiesel-diesel. It was found that lower blends of castor biodiesel are an acceptable fuel alternative for the engine.

  17. Biologic effects of auto emissions. I. Exhaust from engine with and without catalytic converter.

    PubMed

    Lee, S D; Malanchuk, M; Finelli, V N

    1976-05-01

    This paper relates to the efficacy of a catalytic converter in reducing the levels of certain pollutants emitted from an automobile engine and to the reduction and/or elimination of gross biologic damages in animals exposed to emissions from an exhaust system containing such catalysts. Groups of rats were exposed to diluted emissions from an automobile engine with and without catalyst. Concomitantly, a comparative experiment was conducted by exposing a group of rats to carbon monoxide alone (575 mg/m3). The parameters measured included hematocrit, serum LDH, GOT, and lysozyme. An elevation in hematocrit was observed in animals of the experiment run without catalyst and in those exposed to carbon monoxide; the use of the catalyst reduced the carbon monoxide levels in the exposure chambers by more than tenfold and prevented these bioeffects from occurring. Serum LDH activity was elevated in the groups of rats in the experiment conducted without catalyst, but no alternation was observed in the animals from the experiment utilizing the catalyst or in those exposed to carbon monoxide alone. The data obtained in this study showed that acute exposure to noncatalytic emissions caused significant alterations in certain biologic parameters. Conversely, the introduction of an oxidizing catalytic converter into the engine exhaust system reduced or prevented such biologic damage.

  18. Exhaust emissions from a diesel power generator fuelled by waste cooking oil biodiesel.

    PubMed

    Valente, Osmano Souza; Pasa, Vanya Márcia Duarte; Belchior, Carlos Rodrigues Pereira; Sodré, José Ricardo

    2012-08-01

    The exhaust emissions from a diesel power generator operating with waste cooking oil biodiesel blends have been studied. Fuel blends with 25%, 50% and 75% of biodiesel concentration in diesel oil were tested, varying engine load from 0 to 25 kW. The original engine settings for diesel oil operation were kept the same during the experiments with the biodiesel blends. The main physical-chemical characteristics of the fuel blends used were measured to help with the analysis of the emission results. The results show that the addition of biodiesel to the fuel increases oxides of nitrogen (NO(X)), carbon monoxide (CO) and hydrocarbon (HC) emissions. Carbon dioxide (CO(2)) and exhaust gas opacity were also increased with the use of biodiesel. Major increase of NO(X) was observed at low loads, while CO and HC were mainly increased at high loads. Using 50% of biodiesel in diesel oil, the average increase of CO(2), CO, HC and NO(X) throughout the load range investigated was 8.5%, 20.1%, 23.5% and 4.8%, respectively. Copyright © 2012 Elsevier B.V. All rights reserved.

  19. Experimental Evaluation of Rocket Exhaust Diffusers for Altitude Simulation

    NASA Technical Reports Server (NTRS)

    Sivo, Joseph N.; Meyer, Carl L.; Peters, Daniel J.

    1960-01-01

    An experimental investigation of exhaust diffusers has been conducted to evaluate various methods of minimizing the overall pressure ratio (from chamber to ambient pressure) required to establish and maintain full expansion of the nozzle flow (altitude simulation). Exhaust-diffuser configurations investigated were (1) cylindrical diffusers, (2) diffusers with contraction, and (3) diffusers including a right-angle turn. Cylindrical diffusers were evaluated with primary nozzles of various area ratios and types, as well as two clustered configurations; the other diffusers were evaluated with individual nozzles of constant area ratio and varied type. Air was the working fluid, except for two check points obtained with JP-4 fuel and liquid-oxygen rocket engines and cylindrical diffusers. The minimum length-diameter ratio of cylindrical diffusers was about 6 for minimum pressure-ratio requirements. With cylindrical diffusers of adequate length, the pressure-ratio requirements were primarily a function of the ratio of diffuser to nozzle-throat areas and were essentially independent of primary-nozzle type (including two clustered configurations) or area ratio. The two check points obtained with rocket engines indicated the pressure-ratio requirements at given ratios of diffuser to nozzle-throat areas were lowered, as compared with the requirements with air, as a result of the reduced ratio of specific heats. The minimum length-diameter ratio of the contraction throat of convergent-divergent diffusers was also about 6 for minimum pressure-ratio requirements. With adequate contraction-throat length, the pressure-ratio requirements of such diffusers were appreciably below those of comparable cylindrical diffusers when used with conical and cutoff-isentropic nozzles, but not when used with a bell nozzle. Minimum pressure-ratio requirements of a diffuser including a simple long-radius right-angle turn at maximum diffuser area, obtained with the center of radius of the turn a

  20. Effect of exhaust emissions on carbon monoxide levels in employees working at indoor car wash facilities.

    PubMed

    Topacoglu, H; Katsakoglou, S; Ipekci, A

    2014-01-01

    Exhaust emissions from motor vehicles threaten the environment and human health. Carbon monoxide (CO) poisoning, especially the use of exhaust gas CO in suicidal attempts is well known in the literature. Recently, indoor car wash facilities established in large shopping malls with closed parking, lots is a new risk area that exposes car wash employees to prolonged periods of high level CO emissions from cars. The aim of this study was to investigate how carboxyhemoglobin (COHb) blood levels of employees get affected in confined areas with relatively poor air circulation. Twenty male volunteers working in indoor parking car wash facilities were included in the study. Participants were informed about the aim of this study and their consent was obtained. Their pulse COHb levels were measured twice, at the beginning and at the end of the working day using Rad-57 pulse CO-oximeter device, allowing non-invasive measurement of COHb blood levels to compare the changes in their COHb levels before and after work. The mean age of the male volunteers was 29.8 ± 11.9 (range 18-55). While the mean COHb levels measured at the start of the working day was 2.1 ± 2.0 (range 0-9), it was increased to 5.2 ± 3.3 (range 1-15) at the end of work shift (Wilcoxon test, p <0.001). There was a statistically significant difference in COHb levels between the beginning and the end of the work shift in smoker subjects, while the difference was not significant in the non-smoking group (Wilcoxon test, p=0.001, p=0.102, respectively). The COHb blood levels of indoor car wash facility employees is directly impacted and gets elevated by motor vechile exhaust emissions. For the health of the employees at indoor parking car wash facilities, stricter precautions are needed and the government should not give permit to such operations.

  1. Heavy metals from non-exhaust vehicle emissions in urban and motorway road dusts.

    PubMed

    Adamiec, Ewa; Jarosz-Krzemińska, Elżbieta; Wieszała, Robert

    2016-06-01

    The main sources of non-exhaust vehicular emissions that contribute to road dust are tire, brake and clutch wear, road surface wear, and other vehicle and road component degradation. This study is an attempt to identify and investigate heavy metals in urban and motorway road dusts as well as in dust from brake linings and tires. Road dust was collected from sections of the A-4 motorway in Poland, which is part of European route E40, and from urban roads in Katowice, Poland. Dust from a relatively unpolluted mountain road was collected and examined as a control sample. Selected metals Cd, Cr, Cu, Ni, Pb, Zn, Fe, Se, Sr, Ba, Ti, and Pd were analyzed using inductively coupled plasma-mass spectrometry, inductively coupled plasma (ICP)-optical emission spectroscopy, and atomic absorption spectroscopy on a range of size-fractionated road dust and brake lining dust (<20, 20-56, 56-90, 90-250, and >250 μm). The compositions of brake lining and tire dust were also investigated using scanning electron microscopy-energy-dispersive spectroscopy. To estimate the degree of potential environmental risk of non-exhaust emissions, comparison with the geochemical background and the calculations of geo-accumulation indices were performed. The finest fractions of urban and motorway dusts were significantly contaminated with all of the investigated metals, especially with Ti, Cu, and Cr, which are well-recognized key tracers of non-exhaust brake wear. Urban dust was, however, more contaminated than motorway dust. It was therefore concluded that brake lining and tire wear strongly contributed to the contamination of road dust.

  2. Monitoring of carbon dioxide exhaust emissions using mid-infrared spectroscopy

    NASA Astrophysics Data System (ADS)

    Mulrooney, Jim; Clifford, John; Fitzpatrick, Colin; Chambers, Paul; Lewis, Elfed

    2007-06-01

    An optical fibre sensor for monitoring carbon dioxide emissions from modern road vehicles and operating in the mid-infrared spectral region is reported. The wavelength range of operation is centred at 4.23 µm and has required a novel implementation of this sensor using low cost and robust components. The sensor is shown to be capable of detecting CO2 to a minimum level of 350 ppm, to be stable over several hours of continuous operation and insensitive to the presence of other species present in the exhaust.

  3. Opacity meter for monitoring exhaust emissions from non-stationary sources

    DOEpatents

    Dec, John Edward

    2000-01-01

    Method and apparatus for determining the opacity of exhaust plumes from moving emissions sources. In operation, a light source is activated at a time prior to the arrival of a diesel locomotive at a measurement point, by means of a track trigger switch or the Automatic Equipment Identification system, such that the opacity measurement is synchronized with the passage of an exhaust plume past the measurement point. A beam of light from the light source passes through the exhaust plume of the locomotive and is detected by a suitable detector, preferably a high-rate photodiode. The light beam is well-collimated and is preferably monochromatic, permitting the use of a narrowband pass filter to discriminate against background light. In order to span a double railroad track and provide a beam which is substantially stronger than background, the light source, preferably a diode laser, must provide a locally intense beam. A high intensity light source is also desirable in order to increase accuracy at the high sampling rates required. Also included is a computer control system useful for data acquisition, manipulation, storage and transmission of opacity data and the identification of the associated diesel engine to a central data collection center.

  4. Aircraft engine exhaust emissions and other airport-related contributions to ambient air pollution: A review

    NASA Astrophysics Data System (ADS)

    Masiol, Mauro; Harrison, Roy M.

    2014-10-01

    Civil aviation is fast-growing (about +5% every year), mainly driven by the developing economies and globalisation. Its impact on the environment is heavily debated, particularly in relation to climate forcing attributed to emissions at cruising altitudes and the noise and the deterioration of air quality at ground-level due to airport operations. This latter environmental issue is of particular interest to the scientific community and policymakers, especially in relation to the breach of limit and target values for many air pollutants, mainly nitrogen oxides and particulate matter, near the busiest airports and the resulting consequences for public health. Despite the increased attention given to aircraft emissions at ground-level and air pollution in the vicinity of airports, many research gaps remain. Sources relevant to air quality include not only engine exhaust and non-exhaust emissions from aircraft, but also emissions from the units providing power to the aircraft on the ground, the traffic due to the airport ground service, maintenance work, heating facilities, fugitive vapours from refuelling operations, kitchens and restaurants for passengers and operators, intermodal transportation systems, and road traffic for transporting people and goods in and out to the airport. Many of these sources have received inadequate attention, despite their high potential for impact on air quality. This review aims to summarise the state-of-the-art research on aircraft and airport emissions and attempts to synthesise the results of studies that have addressed this issue. It also aims to describe the key characteristics of pollution, the impacts upon global and local air quality and to address the future potential of research by highlighting research needs.

  5. 40 CFR 1042.240 - Demonstrating compliance with exhaust emission standards.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... that all data, analyses, evaluations, and other information you used are available for our review upon... emission standards in § 1042.101(a) or § 1042.104 if all emission-data engines representing that family... standards. This also applies for all test points for emission-data engines within the family used to...

  6. Exhaust emissions from engines of the Detroit Diesel Corporation in transit buses: a decade of trends.

    PubMed

    Prucz, J C; Clark, N N; Gautam, M; Lyons, D W

    2001-05-01

    In the U.S.A., exhaust emissions from city buses fueled by diesel are not characterized well because current emission standards require engine tests rather than tests of whole vehicles. Two transportable chassis dynamometer laboratories developed and operated by West Virginia University (WVU) have been used extensively to gather realistic emission data from heavy-duty vehicles, including buses, tested in simulated driving conditions. A subset of these data has been utilized for a comprehensive introspection into the trends of regulated emissions from transit buses over the last 7 years, which has been prompted by continuously tightening restrictions on one hand, along with remarkable technological progress, on the other hand. Two widely used models of diesel engines manufactured by the Detroit Diesel Corporation (DDC) have been selected as a case-study for such an overview, based on full-scale, on-site testing of actual city buses, driven in accordance with the SAE J1376 standard of a Commercial Business District (CBD) cycle. The results provide solid, quantitative evidence that most regulated emissions from engines produced by DDC have declined over the years, especially with the transition from the 6V-92TA to the Series 50 models. This improvement is remarkable mainly for the emissions of particulate matter (PM), that are lower by over 70%, on average, for the Series 50 engines, though the emissions of nitrogen oxides (NOx) exhibit a reversed trend, showing a degradation of about 6%, on average, with the transition from 6V-92TA to the Series 50 engines. The expected trend of decreasing emission levels with the model year of the engine is clear and consistent for particulate matter (PM), hydrocarbons (HC), carbon monoxide (CO), and nitrogen oxides (NOx), starting with the 1990 models, although it is not conclusive for carbon dioxide (CO2) emissions.

  7. Test and Evaluation of a Pilot Two-Stage Precipitator for Jet Engine Test Cell Exhaust Gas Cleaning

    DTIC Science & Technology

    1976-04-01

    then available for emission control . A two- stage electrostatic precipitator was recommended as .j he most viable alternative to a concept then being...TEST AND EVALUATION OF A "PILOT TWO* STAGE PRECIPITATOR FOR JET ENGINE TEST CELL 0 EXHAUST GA, S CLEANING C44 NAVAL AIR REWORK FACILITY NAVAL AIR...is the release you requested in your telephone conversation of 20 July 1976 with the undersigned. Yourn very tru~ly, Head Specifications Branch a 21

  8. A modelling system for the exhaust emissions of marine traffic and its application in the Baltic Sea area

    NASA Astrophysics Data System (ADS)

    Jalkanen, J.-P.; Brink, A.; Kalli, J.; Pettersson, H.; Kukkonen, J.; Stipa, T.

    2009-12-01

    A method is presented for the evaluation of the exhaust emissions of marine traffic, based on the messages provided by the Automatic Identification System (AIS), which enable the identification and location determination of ships. The use of the AIS data facilitates the positioning of ship emissions with a high spatial resolution, which is limited only by the inaccuracies of the Global Positioning System (typically a few metres) that is used in vessel navigation. The emissions are computed based on the relationship of the instantaneous speed to the design speed, and the detailed technical information of the engines of the ships. The modelling of emissions is also based on a few basic principles of ship design, including the modelling of the propelling power of each vessel in terms of its speed. We have investigated the effect of waves on the consumption of fuel, and on the emissions to the atmosphere. The predictions of fuel consumption were compared with the actual values obtained from the shipowners. For a Roll on - Roll off cargo/passenger ship (RoPax), the predicted and reported values of annual fuel consumption agreed within an accuracy of 6%. According to the data analysis and model computations, the emissions of NOx, SOx and CO2 originating from ships in the Baltic Sea during the full calendar year of 2007 were in total 400 kt, 138 kt and 19 Mt, respectively. A breakdown of emissions by flag state, the type of ship and the year of construction is also presented. The modelling system can be used as a decision support tool in the case of issues concerning, e.g., the health effects caused by shipping emissions or the construction of emission-based fairway dues systems or emissions trading. The computation of emissions can be automated, which will save resources in constructing emission inventories. Both the methodologies and the emission computation program can be applied in any sea region in the world, provided that the AIS data from that specific region are

  9. 40 CFR 1039.101 - What exhaust emission standards must my engines meet after the 2014 model year?

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... engines. (b) Emission standards for steady-state testing. Steady-state exhaust emissions from your engines... the applicable steady-state test procedures described in subpart F of this part. Table 1 of § 1039.101... standard applies to both steady-state and transient testing, as described in paragraphs (a) and (b) of...

  10. 40 CFR 86.1708-99 - Exhaust emission standards for 1999 and later light-duty vehicles.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 19 2010-07-01 2010-07-01 false Exhaust emission standards for 1999 and later light-duty vehicles. 86.1708-99 Section 86.1708-99 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) CONTROL OF EMISSIONS FROM NEW AND IN-USE HIGHWAY VEHICLES AND ENGINES (CONTINUED) General...

  11. 40 CFR 86.1709-99 - Exhaust emission standards for 1999 and later light light-duty trucks.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 19 2010-07-01 2010-07-01 false Exhaust emission standards for 1999 and later light light-duty trucks. 86.1709-99 Section 86.1709-99 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) CONTROL OF EMISSIONS FROM NEW AND IN-USE HIGHWAY VEHICLES AND ENGINES (CONTINUED) General...

  12. 40 CFR 1045.103 - What exhaust emission standards must my outboard and personal watercraft engines meet?

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... types. The exhaust emission standards in this section apply for engines using the fuel type on which the... hydrocarbons in this section based on the following types of hydrocarbon emissions for engines powered by the... my outboard and personal watercraft engines meet? 1045.103 Section 1045.103 Protection of Environment...

  13. 40 CFR 1045.103 - What exhaust emission standards must my outboard and personal watercraft engines meet?

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... types. The exhaust emission standards in this section apply for engines using the fuel type on which the... hydrocarbons in this section based on the following types of hydrocarbon emissions for engines powered by the... my outboard and personal watercraft engines meet? 1045.103 Section 1045.103 Protection of Environment...

  14. 40 CFR 1045.103 - What exhaust emission standards must my outboard and personal watercraft engines meet?

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... types. The exhaust emission standards in this section apply for engines using the fuel type on which the... hydrocarbons in this section based on the following types of hydrocarbon emissions for engines powered by the... my outboard and personal watercraft engines meet? 1045.103 Section 1045.103 Protection of Environment...

  15. 40 CFR 1045.103 - What exhaust emission standards must my outboard and personal watercraft engines meet?

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... exhaust emission standards in this section apply for engines using the fuel type on which the engines in... hydrocarbons in this section based on the following types of hydrocarbon emissions for engines powered by the... my outboard and personal watercraft engines meet? 1045.103 Section 1045.103 Protection of Environment...

  16. 40 CFR 89.112 - Oxides of nitrogen, carbon monoxide, hydrocarbon, and particulate matter exhaust emission standards.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 20 2010-07-01 2010-07-01 false Oxides of nitrogen, carbon monoxide....112 Oxides of nitrogen, carbon monoxide, hydrocarbon, and particulate matter exhaust emission... emissions of oxides of nitrogen, carbon monoxide, hydrocarbon, and nonmethane hydrocarbon are measured...

  17. 40 CFR 89.112 - Oxides of nitrogen, carbon monoxide, hydrocarbon, and particulate matter exhaust emission standards.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 21 2012-07-01 2012-07-01 false Oxides of nitrogen, carbon monoxide....112 Oxides of nitrogen, carbon monoxide, hydrocarbon, and particulate matter exhaust emission... emissions of oxides of nitrogen, carbon monoxide, hydrocarbon, and nonmethane hydrocarbon are measured...

  18. 40 CFR 89.112 - Oxides of nitrogen, carbon monoxide, hydrocarbon, and particulate matter exhaust emission standards.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 21 2013-07-01 2013-07-01 false Oxides of nitrogen, carbon monoxide....112 Oxides of nitrogen, carbon monoxide, hydrocarbon, and particulate matter exhaust emission... emissions of oxides of nitrogen, carbon monoxide, hydrocarbon, and nonmethane hydrocarbon are measured...

  19. 40 CFR 89.112 - Oxides of nitrogen, carbon monoxide, hydrocarbon, and particulate matter exhaust emission standards.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 20 2014-07-01 2013-07-01 true Oxides of nitrogen, carbon monoxide....112 Oxides of nitrogen, carbon monoxide, hydrocarbon, and particulate matter exhaust emission... emissions of oxides of nitrogen, carbon monoxide, hydrocarbon, and nonmethane hydrocarbon are measured...

  20. 40 CFR 89.112 - Oxides of nitrogen, carbon monoxide, hydrocarbon, and particulate matter exhaust emission standards.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 20 2011-07-01 2011-07-01 false Oxides of nitrogen, carbon monoxide....112 Oxides of nitrogen, carbon monoxide, hydrocarbon, and particulate matter exhaust emission... emissions of oxides of nitrogen, carbon monoxide, hydrocarbon, and nonmethane hydrocarbon are measured...

  1. Off-cycle exhaust emissions from modern passenger cars with properly-functioning emissions controls

    SciTech Connect

    Goodwin, R.W.; Ross, M.H.

    1996-09-01

    Real-world tailpipe emissions from properly-functioning, model year 1991--94 conventional gasoline-fueled cars associated with vehicle operations not emphasized in the FTP are analyzed. Tailpipe emissions are expressed as the product of three factors: fuel rate, engine-out emissions index, and catalyst pass fraction, which are modeled using empirical data from the FTP-Revision Project and applied to in-use driving survey data to estimate real-world emissions. Average tailpipe emissions due to fuel enrichment in warmed-up vehicles are estimated to be 8 g/mile for CO, and 0.3 g/mile for HC. For NO{sub x}, the contribution due to incremental loads on the engine (i.e. air conditioner, grade, high acceleration, and high speed) that are not accounted for in the FTP but are encountered in real-world driving are estimated to be roughly 0.3 g/mile.

  2. Nonintrusive optical measurements of aircraft engine exhaust emissions and comparison with standard intrusive techniques.

    PubMed

    Schäfer, K; Heland, J; Lister, D H; Wilson, C W; Howes, R J; Falk, R S; Lindermeir, E; Birk, M; Wagner, G; Haschberger, P; Bernard, M; Legras, O; Wiesen, P; Kurtenbach, R; Brockmann, K J; Kriesche, V; Hilton, M; Bishop, G; Clarke, R; Workman, J; Caola, M; Geatches, R; Burrows, R; Black, J D; Hervé, P; Vally, J

    2000-01-20

    Nonintrusive systems for the measurement on test rigs of aeroengine exhaust emissions required for engine certification (CO, NO(x), total unburned hydrocarbon, and smoke), together with CO(2) and temperature have been developed. These results have been compared with current certified intrusive measurements on an engine test. A spectroscopic database and data-analysis software has been developed to enable Fourier-transform Infrared measurement of concentrations of molecular species. CO(2), CO, and NO data showed agreement with intrusive techniques of approximately ?30%. A narrow-band spectroscopic device was used to measure CO(2) (with deviations of less than ?10% from the intrusive measurement), whereas laser-induced incandescence was used to measure particles. Future improvements to allow for the commercial use of the nonintrusive systems have been identified and the methods are applicable to any measurement of combustion emissions.

  3. Effect of operating conditions on the exhaust emissions from a gas turbine combustor

    NASA Technical Reports Server (NTRS)

    Briehl, D.; Papathakos, L.; Strancar, R. J.

    1972-01-01

    Exhaust concentrations of total unburned hydrocarbons, carbon monoxide, and nitric oxide were measured from a single J-57 combustor liner installed in a 30 diameter test section. Tests were conducted over a range of inlet total pressures from 1 to 20 atmospheres, inlet total temperatures from 310 to 590 K, reference velocities from 8 to m/sec, and fuel-air ratios from 0.004 to 0.015. Most of the data were obtained using ASTM A-1 fuel; however, a limited number of tests was performed with natural gas fuel. Combustion efficiency and emission levels are correlated with operating conditions. Sampling error at operating conditions for which combustion efficiency was below about 90 percent resulted in abnormally low readings for hydrocarbon emissions.

  4. Construction of fuzzy membership functions for urban vehicular exhaust emissions modeling.

    PubMed

    Jain, Suresh; Khare, Mukesh

    2010-08-01

    This paper presents a method for constructing a membership function (MF) for the fuzzy sets that expert systems deal with. This paper introduces a Bezier curve-based mechanism for constructing MFs of convex normal fuzzy sets. The mechanism can fit any given data set with a minimum level of discrepancy. In the absence of data, the mechanism can be intuitively manipulated by the user to construct MFs with the desired shape. MFs have been developed using the proposed mechanism for urban vehicular exhaust emission modeling. It has been observed that all meteorological and vehicular parameters have either S-shaped MFs or Z-shaped MFs. Gaussian MF has been mostly applied for modeling air quality. The present study explored the application of fuzzy MF to analyze air pollution data from vehicular emission. The study reveals that S-shaped and Z-shaped MF can be used in addition to Gaussian MF.

  5. Inhalation toxicology of automotive emissions as affected by an oxidation exhaust catalyst.

    PubMed

    Hysell, D K; Moore, W; Hinners, R; Malanchuk, M; Miller, R; Stara, J F

    1975-04-01

    Preliminary data are given on the acute inhalation toxicology of automotive emissions as affected by an oxidation exhaust catalyst. The catalyst effectively reduced CO and HC in the exhause which apparently had an effect (at least in a closed exposure system) on oxidant and NO2 levels by altering the HC/NOx ratio. There was a resultant reduction in biological effects due to the exposure. The catalyst altered the type of particulate to one which probably contained sulfuric acid as a major component. No evidence was present in these acute exposures to suggest a toxic response due to the higher sulfate emissions or possible catalyst attrition products. The effects of long-term exposure have not yet been investigated.

  6. Monitoring of heavy metal particle emission in the exhaust duct of a foundry using LIBS.

    PubMed

    Dutouquet, C; Gallou, G; Le Bihan, O; Sirven, J B; Dermigny, A; Torralba, B; Frejafon, E

    2014-09-01

    Heavy metals have long been known to be detrimental to human health and the environment. Their emission is mainly considered to occur via the atmospheric route. Most of airborne heavy metals are of anthropogenic origin and produced through combustion processes at industrial sites such as incinerators and foundries. Current regulations impose threshold limits on heavy metal emissions. The reference method currently implemented for quantitative measurements at exhaust stacks consists of on-site sampling of heavy metals on filters for the particulate phase (the most prominent and only fraction considered in this study) prior to subsequent laboratory analysis. Results are therefore known only a few days after sampling. Stiffer regulations require the development of adapted tools allowing automatic, on-site or even in-situ measurements with temporal resolutions. The Laser-Induced Breakdown Spectroscopy (LIBS) technique was deemed as a potential candidate to meet these requirements. On site experiments were run by melting copper bars and monitoring emission of this element in an exhaust duct at a pilot-scale furnace in a French research center dedicated to metal casting. Two approaches designated as indirect and direct analysis were broached in these experiments. The former corresponds to filter enrichment prior to subsequent LIBS interrogation whereas the latter entails laser focusing right through the aerosol for detection. On-site calibration curves were built and compared with those obtained at laboratory scale in order to investigate possible matrix and analyte effects. Eventually, the obtained results in terms of detection limits and quantitative temporal monitoring of copper emission clearly emphasize the potentialities of the direct LIBS measurements. Copyright © 2014 Elsevier B.V. All rights reserved.

  7. Experimental Measurements of the Effects of Photo-chemical Oxidation on Aerosol Emissions in Aircraft Exhaust

    NASA Astrophysics Data System (ADS)

    Miracolo, M. A.; Presto, A. A.; Hennigan, C. J.; Nguyen, N.; Ranjan, M.; Reeder, A.; Lipsky, E.; Donahue, N. M.; Robinson, A. L.

    2009-12-01

    Many military and commercial airfields are located in non-attainment areas for particulate matter (PM2.5), but the contribution of emissions from in-use aircraft to local and regional PM2.5 concentrations is uncertain. In collaboration with the Pennsylvania Air National Guard 171st Air Refueling Wing, the Carnegie Mellon University (CMU) Mobile Laboratory was deployed to measure fresh and aged emissions from a CFM56-2B1 gas-turbine engine mounted on a KC-135 Stratotanker airframe. The CFM-56 family of engine powers many different types of military and civilian aircraft, including the Boeing 737 and several Airbus models. It is one of the most widely deployed models of engines in the world. The goal of this work was to measure the gas-particle partitioning of the fresh emissions at atmospherically relevant conditions and to investigate the effect of atmospheric oxidation on aerosol loadings as the emissions age. Emissions were sampled from an inlet installed one meter downstream of the engine exit plane and transferred into a portable smog chamber via a heated inlet line. Separate experiments were conducted at different engine loads ranging from ground idle to take-off rated thrust. During each experiment, some diluted exhaust was added to the chamber and the volatility of the fresh emissions was then characterized using a thermodenuder. After this characterization, the chamber was exposed to either ambient sunlight or UV lights to initiate photochemical oxidation, which produced secondary aerosol and ozone. A suite of gas and particle-phase instrumentation was used to characterize the evolution of the gas and particle-phase emissions, including an aerosol mass spectrometer (AMS) to measure particle size and composition distributions. Fresh emissions of fine particles varied with engine load with peak emission factors at low and high loads. At high engine loads, the fresh emissions were dominated by black carbon; at low loads volatile organic carbon emissions were

  8. Hanford Site radionuclide national emission standards for hazardous ari pollutants registered and and unregistered stack (powered exhaust) source assessment

    SciTech Connect

    Davis, W.E.

    1995-12-01

    On February 3, 1993, US DOE Richland Operations Office received a Compliance Order and Information Request from the Director of the Air and Toxics Div. of US EPA, Region X. The compliance order requires the Richland Operations Office to evaluate all radionuclide emission points at the Hanford site to determine which are subject to the continuous emission measurement requirements in Title 40, Code of Federal Regulations (CFR), Part 61, Subpart H, and to continuously measure radionuclide emissions in accordance with 40 CFR 61.93. The Information Request required The provision of a written compliance plan to meet the requirements of the compliance order. A compliance plan was submitted to EPA, Region X, on April 30, 1993. It set as one of the milestones, the complete assessment of the Hanford Site 84 stacks registered with the Washington State Department of Health, by December 17, 1993. This milestone was accomplished. The compliance plan also called for reaching a Federal Facility Compliance Agreement; this was reached on February 7, 1994, between DOE Richland Operations and EPA, Region X. The milestone to assess the unregistered stacks (powered exhaust) by August 31, 1994, was met. This update presents assessments for 72 registered and 22 unregistered stacks with potential emissions > 0.1 mrem/yr.

  9. Black carbon emissions in gasoline vehicle exhaust: a measurement and instrument comparison.

    PubMed

    Kamboures, Michael A; Hu, Shishan; Yu, Yong; Sandoval, Julia; Rieger, Paul; Huang, Shiou-Mei; Zhang, Sherry; Dzhema, Inna; Huo, Darey; Ayala, Alberto; Chang, M C Oliver

    2013-08-01

    A pilot study was conducted to evaluate the performance and agreement of several commercially available black carbon (BC) measurement instruments, when applied to the quantification of BC in light-duty vehicle (LDV) exhaust. Samples from six vehicles, three fuels, and three driving cycles were used. The pilot study included determinations of the method detection limit (MDL) and repeatability. With respect to the MDL, the real-time instruments outperformed the time-integrated instruments, with MDL = 0.12 mg/mi for the AE51 Aethalometer, and 0.15 mg/mi for the Micro Soot Sensor (MSS), versus 0.38 mg/mi for the IMPROVE_A thermal/ optical method, and 0.35 mg/mi for the OT21_T Optical Transmissometer. The real-time instruments had repeatability values ranging from 30% to 35%, which are somewhat better than those of the time-integrated instruments (40-41%). These results suggest that, despite being less resource intensive, real-time methods can be equivalent or superior to time-integrated methods in terms of sensitivity and repeatability. BC mass data, from the photoacoustic and light attenuation instruments, were compared against same-test EC data, determined using the IMPROVE_A method. The MSS BC data was well correlated with EC, with R2 = 0.85 for the composite results and R2 = 0.86 for the phase-by-phase (PBP) results. The correlation of BC, by the AE51, AE22, and OT21_T with EC was moderate to weak. The weaker correlation was driven by the inclusion of US06 test data in the linear regression analysis. We hypothesize that test-cycle-dependent BC:EC ratios are due to the different physicochemical properties of particulate matter (PM) in US06 and Federal Test Procedure (FTP) tests. Correlation amongst the real-time MSS, PASS-1, AE51, and AE22 instruments was excellent (R2 = 0.83-0.95), below 1 mg/mi levels. In the process of investigating these BC instruments, we learned that BC emissions at sub-1 mg/mi levels can be measured and are achievable by current

  10. Evaluation of thermal optical analysis method of elemental carbon for marine fuel exhaust.

    PubMed

    Lappi, Maija K; Ristimäki, Jyrki P

    2017-05-26

    The awareness of black carbon (BC) as the second largest anthropogenic contributor in global warming and an ice melting enhancer has increased. Due to prospected increase in shipping especially in the Arctic reliability of BC emissions and their invented amounts from ships is gaining more attention. The International Maritime Organisation (IMO) is actively working towards estimation of quantities and effects of BC especially in the Arctic. IMO has launched work towards constituting a definition for BC and agreeing appropriate methods for its determination from shipping emission sources. In our study we evaluated the suitability of elemental carbon (EC) analysis by thermal-optical transmittance (TOT) method to marine exhausts and possible measures to overcome the analysis interferences related to the chemically complex emissions. The measures included drying with CaSO4, evaporation at 40-180°C, H2O treatment and variation of the sampling method (in-stack and diluted) and its parameters (e.g. dilution ratio, Dr). A re-evaluation of the nominal OC/EC split point was made. Measurement of residual carbon after solvent extraction (TC-CSOF) was used as a reference, and later also filter smoke number (FSN) measurement, which is dealt with in a forthcomingpaper by the authors. Exhaust sources used for collecting the particle sample were mainly 4-stroke marine engines operated with variable loads and marine fuels ranging from light to heavy fuel oils (LFO and HFO) with sulphur content range of <0.1-2.4% S. The results were found to be dependent on many factors, i.e. sampling, preparation and analysis method and fuel quality. It was found that the condensed H2SO4+H2O on the PM filter had an effect on the measured EC content, and also promoted the formation of pyrolytic carbon (PyC) from OC, affecting the accuracy of EC determination. Thus uncertainty remained regarding the EC results from HFO fuels. Implications The work boosts as one part decision making in black carbon (BC

  11. Biological activity of particle exhaust emissions from light-duty diesel engines.

    PubMed

    Carraro, E; Locatelli, A L; Ferrero, C; Fea, E; Gilli, G

    1997-01-01

    assays were available, exhaust emission generation by biodiesel fuel seemed to yield a smaller environmental impact than that of the referenced diesel fuel. The results point out the usefulness of mutagenicity testing in the research of both newer, more efficient automotive aftertreatment devices and less polluting fuels.

  12. Assessing the influence of methanol-containing additive on biological characteristics of diesel exhaust emissions using microtox and mutatox assays.

    PubMed

    Lin, Ta-Chang; Chao, Mu-Rong

    2002-02-04

    Here we investigate the effect of the methanol-containing additive (MCA) on the biological characteristics of diesel exhaust emissions. Microtox and Mutatox assays, respectively, were used to evaluate the acute toxicity and genotoxicity of crude extracts from diesel engine exhaust. The engine was tested on a series of diesel fuels blended with five additive levels (0, 5, 8, 10 and 15% of MCA by volume). Emission tests were performed over the hot start portion of the transient Heavy-Duty-Federal Test Procedure (HD-FTP) and two selected steady-state modes. Microtox results show that MCA additive moderately lowers the toxicity levels of particle-associated (SOF) samples, but generally increase the vapor-phase (XOC) associated toxicity. A strong correlation was found between XOC-associated toxicity and total hydrocarbon (THC) concentrations, while only a slight link was found between SOF-associated toxicity and particulate matter (PM) concentrations. For Mutatox test results, when either 5 or 8% MCA used, XOC and SOF-associated genotoxicity in both steady-state and hot-start transient cycle tests were relatively lower compared to those of the base diesel. The genotoxic potential of XOC samples was significantly increased after treatment with an exogenous metabolic activation system (S9). On the contrary, the genotoxic potential of SOF samples without S9 metabolic activation was generally higher than those with S9. It is noteworthy that the total particle-associated (SOF) PAHs emissions showed trends quite similar to that of the genotoxic potential. As expected, the total particle-associated (SOF) PAHs correlated moderately with direct mutagenicity, and fairly well with indirect mutagenicity. Finally, the genotoxicity data did not parallel the Microtox results in this study, indicating that potentially long-term genotoxic agents may not be revealed by short-term toxicity assays.

  13. Role of Neprilysin in Airway Inflammation Induced by Diesel Exhaust Emissions

    PubMed Central

    Wong, Simon S.; Sun, Nina N.; Fastje, Cynthia D.; Witten, Mark L.; Lantz, R. Clark; Lu, Bao; Sherrill, Duane L.; Gerard, Craig J.; Burgess, Jefferey L.

    2016-01-01

    In this study, we examined the role of neprilysin (NEP*), a key membrane-bound endopeptidase, in the inflammatory response induced by diesel exhaust emissions (DEE) in the airways through a number of approaches: in vitro, animal, and controlled human exposure. Our specific aims were (1) to examine the role of NEP in inflammatory injury induced by diesel exhaust particles (DEP) using Nep-intact (wild-type) and Nep-null mice; (2) to examine which components of DEP are associated with NEP downregulation in vitro; (3) to determine the molecular impact of DEP exposure and decreased NEP expression on airway epithelial cells’ gene expression in vitro, using a combination of RNA interference (RNAi) and microarray approaches; and (4) to evaluate the effects on NEP activity of human exposure to DEE. We report four main results: First, we found that exposure of normal mice to DEP consisting of standard reference material (SRM) 2975 via intratracheal installation can downregulate NEP expression in a concentration-dependent manner. The changes were accompanied by increases in the number of macrophages and epithelial cells, as well as proinflammatory cytokines, examined in bronchoalveolar lavage (BAL) fluid and cells. Nep-null mice displayed increased and/or additional inflammatory responses when compared with wild-type mice, especially in response to exposure to the higher dose of DEP that we used. These in vivo findings suggest that loss of NEP in mice could cause increased susceptibility to injury or exacerbate inflammatory responses after DEP exposure via release of specific cytokines from the lungs. Second, we found evidence, using in vitro studies, that downregulation of NEP by DEP in cultured human epithelial BEAS-2B cells was mostly attributable to DEP-adsorbed organic compounds, whereas the carbonaceous core and transition metal components of DEP had little or no effect on NEP messenger RNA (mRNA) expression. This NEP downregulation was not a specific response to DEP

  14. Energy consumption and exhaust emissions in mechanized timber harvesting operations in Sweden.

    PubMed

    Athanassiadis, D

    2000-06-08

    The study presents an estimation of the energy input and the amount of emissions to air due to fuel, chainsaw and hydraulic oil consumption by heavy duty diesel engine vehicles operating in forest logging operations in Sweden. Exhaust concentrations are given for carbon dioxide, carbon monoxide, nitrogen oxides, hydrocarbons and particulate matter. Three fuel types (rapeseed methyl ester, environmental class 1 and environmental class 3 diesel fuels) and two types of lubricating base oil (mineral- and vegetable-based) were examined. Energy input per unit of timber production (m3ub) was 82 MJ, 11% of which was due to energy consumption during the production phase of the fuel. Emissions during the whole life cycle of the fuels and the base oils are included in the study. The highest CO2 and NOx emissions occurred when rapeseed methyl ester was used as fuel together with rapeseed as base oil for chainsaw and hydraulic oil. The highest HC and CO emissions occurred when environmental class 3 diesel fuel was used.

  15. The significance of vehicle emissions standards for levels of exhaust pollution from light vehicles in an urban area

    NASA Astrophysics Data System (ADS)

    Rhys-Tyler, G. A.; Legassick, W.; Bell, M. C.

    2011-06-01

    This paper addresses the research question "Are more stringent exhaust emissions standards, as applied to light vehicle type approval, resulting in reduced vehicle pollution in an urban area?" The exhaust emissions of a sample of over fifty thousand road vehicles operating in London were measured using roadside remote sensing absorption spectroscopy techniques (infrared and ultraviolet), combined with Automatic Number Plate Recognition for vehicle identification. Levels of carbon monoxide (CO), hydrocarbons (HC), nitric oxide (NO), and smoke (particulate) exhaust emissions are reported by vehicle class, fuel type, and Euro emissions standard. Emissions from petrol cars of each pollutant were all observed to display a statistically significant reduction with the introduction of each successive Euro emissions standard from Euro 1 onwards. However, Euro 2 diesel cars were observed to emit statistically higher rates of NO than either Euro 1 or Euro 3 standard diesel cars. The study also confirms the continuing 'dieselisation' of the UK passenger car fleet. Mean NO emissions from Euro 4 diesel cars were found to be 6 times higher than Euro 4 petrol cars, highlighting the need to develop a sound understanding of the current and future 'in-use' emissions characteristics of diesel vehicles, and their influence on local air quality. Smoke emissions from TXII London taxis (black cabs) were found to be statistically higher than either earlier TX1 or later TX4 model variants, with possible implications for local air quality policy interventions such as maximum age limits for taxis.

  16. 40 CFR 600.008 - Review of fuel economy, CO2 emissions, and carbon-related exhaust emission data, testing by the...

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 31 2013-07-01 2013-07-01 false Review of fuel economy, CO2 emissions... Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) ENERGY POLICY FUEL ECONOMY AND GREENHOUSE GAS EXHAUST EMISSIONS OF MOTOR VEHICLES General Provisions § 600.008 Review of fuel economy,...

  17. 40 CFR 600.113-12 - Fuel economy, CO2 emissions, and carbon-related exhaust emission calculations for FTP, HFET, US06...

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... emissions and carbon-related exhaust emissions for electric vehicles, fuel cell vehicles, and plug-in hybrid electric vehicles according to the provisions of this paragraph (n). Subject to the limitations on the... the proportion of electric operation of a electric vehicles and plug-in hybrid electric vehicles that...

  18. 40 CFR 600.113-12 - Fuel economy, CO2 emissions, and carbon-related exhaust emission calculations for FTP, HFET, US06...

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... determine CO2 emissions and carbon-related exhaust emissions for electric vehicles, fuel cell vehicles, and plug-in hybrid electric vehicles according to the provisions of this paragraph (m). Subject to the... cell vehicles and the proportion of electric operation of a electric vehicles and plug-in hybrid...

  19. Construction and evaluation of a self rating scale for stress-induced Exhaustion Disorder, the Karolinska Exhaustion Disorder Scale

    PubMed Central

    Besèr, Aniella; Sorjonen, Kimmo; Wahlberg, Kristina; Peterson, Ulla; Nygren, Åke; Åsberg, Marie

    2014-01-01

    Prolonged stress (≥ six months) may cause a condition which has been named exhaustion disorder (ED) with ICD-10 code F43.8. ED is characterised by exhaustion, cognitive problems, poor sleep and reduced tolerance to further stress. ED can cause long term disability and depressive symptoms may develop. The aim was to construct and evaluate a self-rating scale, the Karolinska Exhaustion Disorder Scale (KEDS), for the assessment of ED symptoms. A second aim was to examine the relationship between self-rated symptoms of ED, depression, and anxiety using KEDS and the Hospital Anxiety and Depression Scale (HAD). Items were selected based on their correspondence to criteria for ED as formulated by the Swedish National Board of Health and Welfare (NBHW), with seven response alternatives in a Likert-format. Self-ratings performed by 317 clinically assessed participants were used to analyse the scale’s psychometric properties. KEDS consists of nine items with a scale range of 0–54. Receiver operating characteristics analysis demonstrated that a cut-off score of 19 was accompanied by high sensitivity and specificity (each above 95%) in the discrimination between healthy subjects and patients with ED. Reliability was satisfactory and confirmatory factor analysis revealed that ED, depression and anxiety are best regarded as different phenomena. KEDS may be a useful tool in the assessment of symptoms of Exhaustion Disorder in clinical as well as research settings. There is evidence that the symptom clusters of ED, anxiety and depression, respectively, reflect three different underlying dimensions. PMID:24236500

  20. Real-world vehicle emissions as measured by in situ analysis of exhaust plumes.

    PubMed

    Peitzmeier, Christian; Loschke, Carmen; Wiedenhaus, Hanna; Klemm, Otto

    2017-08-23

    We conducted a 60-day roadside measurement campaign on a busy street in Münster, Germany, during summer 2016. We used gas and particle concentration measurements with high temporal resolution (10 Hz) to quantify both the emission ratios of nitrogen oxides per carbon dioxide (NO x /CO2) for over 70,000 individual exhaust plumes as well as the emission ratios for size-resolved particle numbers per carbon dioxide (d(PN CO2(-1))/dlogD) for about 10,000 plumes. The real-world fleet passing by the measurement station consisted of passenger cars (85%), buses (5.9%), light duty commercial vehicles (5.7%), trucks (1.7%), and motorcycles (1.6%). The median measured NO x /CO2 ratio was 3.33 g kg(-1). The median measured PN/CO2 emission ratio for particles with diameters between 0.03 and 10 μm was 5.6 × 10(14) kg(-1). We compared our results with the Handbook Emission Factors for Road Transport (HBEFA) and the Euro 5 and Euro 6 emission standards by employing traffic counts, assuming the diesel-to-gasoline ratios of vehicles according to registration statistics, and estimating that stop-and-go traffic occurred 65% of the time. Using a conservative estimate, our median ratios exceeded the HBEFA data by more than 65% for NO x /CO and by a factor of about 100 for PN/CO2. Furthermore, our median NO x emission per kilometer travelled (NO x  km(-1)) exceeded the Euro 5 emission limit for diesel cars by a factor of 3 and exceeded the Euro 6 limit by almost a factor of 7. Additionally, our median particle number emission (PN km(-1)) exceeded the Euro 5 and Euro 6 limits of diesel cars by a factor of almost 150. These results confirm the presumption that the emissions of a real-world traffic fleet comprehensively exceed the legal limits. Very likely, the widespread presence of defeat devices in vehicle emission control systems plays a major role in this discrepancy. This has a strong impact on the apparent inability of authorities to comply with the legal limits of the NO2

  1. 40 CFR 1066.835 - Exhaust emission test procedure for SC03 emissions.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... major modifications affecting the solar simulation. Determine uniformity by measuring radiant energy... emission measurements. (3) Solar heat load. Simulate solar heating as follows: (i) You may use a metal halide lamp, a sodium lamp, or a quartz halogen lamp with dichroic mirrors as a radiant energy emitter...

  2. AN ENGINE EXHAUST PARTICLE SIZERTM SPECTROMETER FOR TRANSIENT EMISSION PARTICLE MEASUREMENTS

    SciTech Connect

    Johnson, T; Caldow, R; Pucher, A; Mirme, A; Kittelson, D

    2003-08-24

    There has been increased interest in obtaining size distribution data during transient engine operation where both particle size and total number concentrations can change dramatically. Traditionally, the measurement of particle emissions from vehicles has been a compromise based on choosing between the conflicting needs of high time resolution or high particle size resolution for a particular measurement. Currently the most common technique for measuring submicrometer particle sizes is the Scanning Mobility Particle Sizer (SMPSTM) system. The SMPS system gives high size resolution but requires an aerosol to be stable over a long time period to make a particle size distribution measurement. A Condensation Particle Counter (CPC) is commonly used for fast time response measurements but is limited to measuring total concentration only. This paper describes a new instrument, the Engine Exhaust Particle SizerTM (EEPSTM) spectrometer, which has high time resolution and a reasonable size resolution. The EEPS was designed specifically for measuring engine exhaust and, like the SMPS system, uses a measurement based on electrical mobility. Particles entering the instrument are charged to a predictable level, then passed through an annular space where they are repelled outward by the voltage from a central column. When the particles reach electrodes on the outer cylindrical (a column of rings), they create a current that is measured by an electrometer on one or more of the rings. The electrometer currents are measured multiple times per second to give high time resolution. A sophisticated realtime inversion algorithm converts the currents to particle size and concentration for immediate display.

  3. AN ENGINE EXHAUST PARTICLE SIZER{trademark} SPECTROMETER FOR TRANSIENT EMISSION PARTICLE MEASUREMENTS

    SciTech Connect

    Johnson, T: Caldow, R; Pucher, A Mirme, A Kittelson, D

    2003-08-24

    There has been increased interest in obtaining size distribution data during transient engine operation where both particle size and total number concentrations can change dramatically. Traditionally, the measurement of particle emissions from vehicles has been a compromise based on choosing between the conflicting needs of high time resolution or high particle size resolution for a particular measurement. Currently the most common technique for measuring submicrometer particle sizes is the Scanning Mobility Particle Sizer (SMPSTM) system. The SMPS system gives high size resolution but requires an aerosol to be stable over a long time period to make a particle size distribution measurement. A Condensation Particle Counter (CPC) is commonly used for fast time response measurements but is limited to measuring total concentration only. This paper describes a new instrument, the Engine Exhaust Particle SizerTM (EEPSTM) spectrometer, which has high time resolution and a reasonable size resolution. The EEPS was designed specifically for measuring engine exhaust and, like the SMPS system, uses a measurement based on electrical mobility. Particles entering the instrument are charged to a predictable level, then passed through an annular space where they are repelled outward by the voltage from a central column. When the particles reach electrodes on the outer cylindrical (a column of rings), they create a current that is measured by an electrometer on one or more of the rings. The electrometer currents are measured multiple times per second to give high time resolution. A sophisticated realtime inversion algorithm converts the currents to particle size and concentration for immediate display.

  4. Radioactive air emissions notice of construction use of a portable exhauster on single shell tanks (SSTs) during salt well pumping

    SciTech Connect

    GRANDO, C.J.

    1999-11-18

    This document serves as a notice of construction (NOC), pursuant to the requirements of Washington Administrative Code (WAC) 246-247-060, and as a request for approval to construct, pursuant to 40 Code of Federal Regulations (CFR) 61.07, portable exhausters for use on single-shell tanks (SSTs) during salt well pumping. Table 1-1 lists 18 SSTs covered by this NOC. This NOC also addresses other activities that are performed in support of salt well pumping but do not require the application of a portable exhauster. Specifically this NOC analyzes the following three activities that have the potential for emissions. (1) Salt well pumping (i.e., the actual transferring of waste from one tank to another) under nominal tank operating conditions. Nominal tank operating conditions include existing passive breathing rates. (2) Salt well pumping (the actual transferring of waste from one tank to another) with use of a portable exhauster. (3) Use of a water lance on the waste to facilitate salt well screen and salt well jet pump installation into the waste. This activity is to be performed under nominal (existing passive breathing rates) tank operating conditions. The use of portable exhausters represents a cost savings because one portable exhauster can be moved back and forth between SSTs as schedules for salt well pumping dictate. A portable exhauster also could be used to simultaneously exhaust more than one SST during salt well pumping.

  5. Effects of prevaporized fuel on exhaust emissions of an experimental gas turbine combustor

    NASA Technical Reports Server (NTRS)

    Norgren, C. T.; Ingebo, R. D.

    1973-01-01

    Effects of fuel vaporization on the exhaust emission levels of oxides of nitrogen (NOX), carbon monoxide, total hydrocarbons, and smoke number were obtained in an experimental turbojet combustor segment. Two fuel injector types were used in which liquid ASTM A-1 jet fuel and vapor propane fuel were independently controlled to simulate varying degrees of vaporization. Tests were conducted over a range of inlet-air temperatures from 478 to 700 K (860 to 1260 R), pressures from 4 to 20 atmospheres, and combustor reference velocities from 15.3 to 27.4 m/sec (50 to 90 ft/sec). Converting from liquid to complete vapor fuel resulted in NOX reductions as much as 22 percent and smoke number reductions up to 51 percent.

  6. Polycyclic aromatic hydrocarbons and the unidentified infrared emission bands - Auto exhaust along the Milky Way

    NASA Technical Reports Server (NTRS)

    Allamandola, L. J.; Tielens, A. G. G. M.; Barker, J. R.

    1985-01-01

    The unidentified infrared emission features (UIR bands) are attributed to a collection of partially hydrogenated, positively charged polycyclic aromatic hydrocarbons (PAHs). This assignment is based on a spectroscopic analysis of the UIR bands. Comparison of the observed interstellar 6.2 and 7.7-micron bands with the laboratory measured Raman spectrum of a collection of carbon-based particulates (auto exhaust) shows a very good agreement, supporting this identification. The infrared emission is due to relaxation from highly vibrationally and electronically excited states. The excitation is probably caused by UV photon absorption. The infrared fluorescence of one particular, highly vibrationally excited PAH (chrysene) is modeled. In this analysis the species is treated as a molecule rather than bulk material and the non-thermodynamic equilibrium nature of the emission is fully taken into account. From a comparison of the observed ratio of the 3.3 to 11.3-micron UIR bands with the model calculations, the average number of carbon atoms per molecule is estimated to be about 20. The abundance of interstellar PAHs is calculated to be about 2 x 10 to the -7th with respect to hydrogen.

  7. Polycyclic aromatic hydrocarbons and the unidentified infrared emission bands - Auto exhaust along the Milky Way

    NASA Technical Reports Server (NTRS)

    Allamandola, L. J.; Tielens, A. G. G. M.; Barker, J. R.

    1985-01-01

    The unidentified infrared emission features (UIR bands) are attributed to a collection of partially hydrogenated, positively charged polycyclic aromatic hydrocarbons (PAHs). This assignment is based on a spectroscopic analysis of the UIR bands. Comparison of the observed interstellar 6.2 and 7.7-micron bands with the laboratory measured Raman spectrum of a collection of carbon-based particulates (auto exhaust) shows a very good agreement, supporting this identification. The infrared emission is due to relaxation from highly vibrationally and electronically excited states. The excitation is probably caused by UV photon absorption. The infrared fluorescence of one particular, highly vibrationally excited PAH (chrysene) is modeled. In this analysis the species is treated as a molecule rather than bulk material and the non-thermodynamic equilibrium nature of the emission is fully taken into account. From a comparison of the observed ratio of the 3.3 to 11.3-micron UIR bands with the model calculations, the average number of carbon atoms per molecule is estimated to be about 20. The abundance of interstellar PAHs is calculated to be about 2 x 10 to the -7th with respect to hydrogen.

  8. Potential dilemma: the methods of meeting automotive exhaust emission standards of the clean air act of 1970.

    PubMed

    Piver, W T

    1974-08-01

    This review attempts to provide an overview of the interconnected industrial changes associated with compliance with the exhaust emission standards of the Clean Air Act of 1970. To understand the complex nature of air pollution problems, Federal legislation, and compliance with this legislation requires an understanding of automotive technology, petroleum refining, atmospheric chemistry and physics, economics, and public health. The endeavors of all of these different areas impinge to a greater or lesser extent on the final response to the Clean Air Act which is designed to safeguard public health. This overview begins by examining gasoline refinery practice and gasoline composition. Included in this discussion are average values for trace contaminants in gasoline, and an explanation of the function of the many gasoline additives. Next, exhaust emissions are characterized, average values of exhaust components given, and a summary of important atmospheric air pollution reactions presented. Emission control devices and sulfate emissions from these devices are described. This is followed by a complete discussion of methyl cyclopentadienyl manganese tricarbonyl, a substitute antiknock for tetraethyllead. In the event TEL is legally banned from gasoline, or removed because it poisons the catalytic muffler surface, this manganese antiknock is the most efficaous replacement. In this discussion, the adverse health effects caused by exposure to manganese oxide particulates, the possible exhaust emission products from this additive, are examined in detail. The review concludes with comments on automotive engine and gasoline composition redesign as an approach to automotive air pollution.

  9. Potential Dilemma: The Methods of Meeting Automotive Exhaust Emission Standards of the Clean Air Act of 1970

    PubMed Central

    Piver, Warren T.

    1974-01-01

    This review attempts to provide an overview of the interconnected industrial changes associated with compliance with the exhaust emission standards of the Clean Air Act of 1970. To understand the complex nature of air pollution problems, Federal legislation, and compliance with this legislation requires an understanding of automotive technology, petroleum refining, atmospheric chemistry and physics, economics, and public health. The endeavors of all of these different areas impinge to a greater or lesser extent on the final response to the Clean Air Act which is designed to safeguard public health. This overview begins by examining gasoline refinery practice and gasoline composition. Included in this discussion are average values for trace contaminants in gasoline, and an explanation of the function of the many gasoline additives. Next, exhaust emissions are characterized, average values of exhaust components given, and a summary of important atmospheric air pollution reactions presented. Emission control devices and sulfate emissions from these devices are described. This is followed by a complete discussion of methyl cyclopentadienyl manganese tricarbonyl, a substitute antiknock for tetraethyllead. In the event TEL is legally banned from gasoline, or removed because it poisons the catalytic muffler surface, this manganese antiknock is the most efficaous replacement. In this discussion, the adverse health effects caused by exposure to manganese oxide particulates, the possible exhaust emission products from this additive, are examined in detail. The review concludes with comments on automotive engine and gasoline composition redesign as an approach to automotive air pollution. PMID:4143457

  10. Primary Emission and the Potential of Secondary Aerosol Formation from Chinese Gasoline Engine Exhaust

    NASA Astrophysics Data System (ADS)

    Hu, Min; Peng, Jianfei; Qin, Yanhong; Du, Zhuofei; Li, Mengjin; Zheng, Rong; Zheng, Jing; Shang, Dongjie; Lu, Sihua; Wu, Yusheng; Zeng, Limin; Guo, Song; Shao, Min; Wang, Yinhui; Shuai, Shijin

    2017-04-01

    Along with the urbanization and economic growth, vehicle population in China reached 269 million, ranked the second in the world in 2015. Gasoline vehicle is identified to be the main source for urban PM2.5 in China, accounting for 15%-31%. In this study the impact of fuel components on PM2.5 and volatile organic compounds (VOCs) emissions from a gasoline port fuel injection (PFI) engine and a gasoline direct injection (GDI) engine are discussed. Results show that, higher proportion of aromatics, alkenes or sulfur in gasoline fuel will lead to higher PM emissions. The PM from the PFI engine mainly consists of OC and a small amount of EC and inorganic ions, while the PM discharge from the GDI engine mainly consists of EC, OM and a small amount of inorganic ions. Since the GDI engines can reduce fuel consumption and CO2 emissions, and it would become more and more popular in the near future. The characteristics of POM component, emission factors and source profile were investigated from GDI engine, particularly focused on the effect of engine speed, load and the catalyst, which will be very much helpful for source identification as source indicators. Chamber experiments were conducted to quantify the potential of secondary aerosol formation from exhaust of a PFI gasoline engine and China V gasoline fuel. During 4-5 h simulation, equivalent to10 days of atmospheric photo-oxidation in Beijing, the extreme SOA production was 426 ± 85 mg/kg fuel, with high precursors and OH exposure. 14% of SOA measured in the chamber experiments could be explained through the oxidation of speciated single-ring aromatics. Unspeciated precursors, such as intermediate-volatility organic compounds and semi-volatility organic compounds, might be significant for SOA formation from gasoline VOCs. We concluded that reduction of emissions of aerosol precursor gases from vehicles is essential to mediate pollution in China.

  11. Evaluation of Diesel Exhaust Continuous Monitors in Controlled Environmental Conditions

    PubMed Central

    Yu, Chang Ho; Patton, Allison P.; Zhang, Andrew; Fanac, Zhi-Hua (Tina); Weisel, Clifford P.; Lioy, Paul J.

    2015-01-01

    Diesel exhaust (DE) contains a variety of toxic air pollutants, including diesel particulate matter (DPM) and gaseous contaminants (e.g., carbon monoxide (CO)). DPM is dominated by fine (PM2.5) and ultrafine particles (UFP), and can be representatively determined by its thermal-optical refractory as elemental carbon (EC) or light-absorbing characteristics as black carbon (BC). The currently accepted reference method for sampling and analysis of occupational exposure to DPM is the National Institute for Occupational Safety and Health (NIOSH) Method 5040. However, this method cannot provide in-situ short-term measurements of DPM. Thus, real-time monitors are gaining attention to better examine DE exposures in occupational settings. However, real-time monitors are subject to changing environmental conditions. Field measurements have reported interferences in optical sensors and subsequent real-time readings, under conditions of high humidity and abrupt temperature changes. To begin dealing with these issues, we completed a controlled study to evaluate five real-time monitors: Airtec real-time DPM/EC Monitor, TSI SidePak Personal Aerosol Monitor AM510 (PM2.5), TSI Condensation Particle Counter 3007, microAeth AE51 BC Aethalometer, and Langan T15n CO Measurer. Tests were conducted under different temperatures (55, 70, and 80 °F), relative humidity (10, 40, and 80%), and DPM concentrations (50 and 200 µg/m3) in a controlled exposure facility. The 2-hour averaged EC measurements from the Airtec instrument showed relatively good agreement with NIOSH Method 5040 (R2=0.84; slope=1.17±0.06; N=27) and reported ~17% higher EC concentrations than the NIOSH reference method. Temperature, relative humidity, and DPM levels did not significantly affect relative differences in 2-hour averaged EC concentrations obtained by the Airtec instrument versus the NIOSH method (p<0.05). Multiple linear regression analyses, based on 1-min averaged data, suggested combined effects of up to 5

  12. Development of the methodology of exhaust emissions measurement under RDE (Real Driving Emissions) conditions for non-road mobile machinery (NRMM) vehicles

    NASA Astrophysics Data System (ADS)

    Merkisz, J.; Lijewski, P.; Fuc, P.; Siedlecki, M.; Ziolkowski, A.

    2016-09-01

    The paper analyzes the exhaust emissions from farm vehicles based on research performed under field conditions (RDE) according to the NTE procedure. This analysis has shown that it is hard to meet the NTE requirements under field conditions (engine operation in the NTE zone for at least 30 seconds). Due to a very high variability of the engine conditions, the share of a valid number of NTE windows in the field test is small throughout the entire test. For this reason, a modification of the measurement and exhaust emissions calculation methodology has been proposed for farm vehicles of the NRMM group. A test has been developed composed of the following phases: trip to the operation site (paved roads) and field operations (including u-turns and maneuvering). The range of the operation time share in individual test phases has been determined. A change in the method of calculating the real exhaust emissions has also been implemented in relation to the NTE procedure.

  13. An evaluation of a local exhaust ventilation control system for a foundry casting-cleaning operation.

    PubMed

    Gressel, M G

    1997-05-01

    A study was conducted to evaluate the effectiveness of a local exhaust ventilation system for a foundry casting-cleaning operation in which a worker cleaned gray iron castings using a variety of handheld chipping and grinding tools. The operation originally had an exhaust system consisting only of an exhaust duct terminating approximately 1 m (3 ft) above the floor and 2 m (6 ft) from the casting-cleaning workstation. An earlier evaluation of this original control system found time-weighted average exposures to respirable silica ranging from 124 to 160 micrograms/m3. The local exhaust ventilation system evaluated in this present study consisted of a downdraft booth outfitted with a turntable for manipulating the castings. The modified local exhaust ventilation system was installed at this facility and connected to the existing plant exhaust ventilation system through the original ductwork. A direct-reading instrument was used to measure the operator's respirable aerosol exposure concentrations during a single day both before and after the installation of the new workstation. The same worker was sampled both times. The operator's activities were recorded on videotape so that the exposures associated with the various tools could be determined. While day-to-day variability could not be accounted for, depending on the type of tool used the local exhaust ventilation system reduced exposures by 59 to 79% during casting cleaning by the sampled worker when compared with the original configuration. These reductions were statistically significant.

  14. Nondispersive infrared monitoring of NO emissions in exhaust gases of vehicles

    NASA Astrophysics Data System (ADS)

    de Castro, A. J.; Meneses, J.; Briz, S.; López, F.

    1999-07-01

    Road traffic is one of the most important contributors to air pollution, being that a small fraction of the running vehicles is responsible for more than a half of the emissions. Roadside emission monitoring of individual cars appears to be an efficient way to identify these gross polluters. In this sense, nondispersive infrared (NDIR) systems have been developed to monitor the gas emissions of individual vehicles. However, these systems do not include NOx detection because of the strong interference of NO and NO2 absorption bands with the water band. This work is focused on the roadside monitoring of NO emissions by NDIR techniques. A theoretical study of the interference between NO and H2O absorption bands in the 1800-1950 cm-1 spectral region has been performed. Two absorption lines, centered at 1876 and 1900 cm-1 have been selected due to the very low water interference. The development of a new application based on the buildup of a high order interference filter, the solid state Fabry-Pérot filter, is presented. Design of the filter system has been done, optimizing the transmittance at these two absorption lines. Finally, the ability of such a filter to discriminate NO absorption has been tested by using experimental absorption spectra measured by a commercial Fourier transform infrared spectroradiometer working in the active mode. The buildup of such a filter would permit us to increase the capabilities of on road exhaust monitoring systems using the NDIR technique, extending the range of analyzed gases to the nitrogen oxides.

  15. Effect of measurement protocol on organic aerosol measurements of exhaust emissions from gasoline and diesel vehicles

    NASA Astrophysics Data System (ADS)

    Kim, Youngseob; Sartelet, Karine; Seigneur, Christian; Charron, Aurélie; Besombes, Jean-Luc; Jaffrezo, Jean-Luc; Marchand, Nicolas; Polo, Lucie

    2016-09-01

    Exhaust emissions of semi-volatile organic compounds (SVOC) from passenger vehicles are usually estimated only for the particle phase via the total particulate matter measurements. However, they also need to be estimated for the gas phase, as they are semi-volatile. To better estimate SVOC emission factors of passenger vehicles, a measurement campaign using a chassis dynamometer was conducted with different instruments: (1) a constant volume sampling (CVS) system in which emissions were diluted with filtered air and sampling was performed on filters and polyurethane foams (PUF) and (2) a Dekati Fine Particle Sampler (FPS) in which emissions were diluted with purified air and sampled with on-line instruments (PTR-ToF-MS, HR-ToF-AMS, MAAP, CPC). Significant differences in the concentrations of organic carbon (OC) measured by the instruments are observed. The differences can be explained by sampling artefacts, differences between (1) the time elapsed during sampling (in the case of filter and PUF sampling) and (2) the time elapsed from emission to measurement (in the case of on-line instruments), which vary from a few seconds to 15 min, and by the different dilution factors. To relate elapsed times and measured concentrations of OC, the condensation of SVOC between the gas and particle phases is simulated with a dynamic aerosol model. The simulation results allow us to understand the relation between elapsed times and concentrations in the gas and particle phases. They indicate that the characteristic times to reach thermodynamic equilibrium between gas and particle phases may be as long as 8 min. Therefore, if the elapsed time is less than this characteristic time to reach equilibrium, gas-phase SVOC are not at equilibrium with the particle phase and a larger fraction of emitted SVOC will be in the gas phase than estimated by equilibrium theory, leading to an underestimation of emitted OC if only the particle phase is considered or if the gas-phase SVOC are estimated

  16. 40 CFR 600.510-12 - Calculation of average fuel economy and average carbon-related exhaust emissions.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 29 2010-07-01 2010-07-01 false Calculation of average fuel economy... ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) ENERGY POLICY FUEL ECONOMY AND CARBON-RELATED EXHAUST EMISSIONS OF MOTOR VEHICLES Fuel Economy Regulations for Model Year 1978 Passenger Automobiles and for 1979 and Later...

  17. 14 CFR 34.23 - Exhaust Emission Standards for Engines Manufactured on and after July 18, 2012.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... applicable standard if the testing results show that the engine type certificate family's characteristic...: (1) For Classes TF, T3 and T8 engines of a type or model of which the first individual production... 14 Aeronautics and Space 1 2014-01-01 2014-01-01 false Exhaust Emission Standards for Engines...

  18. 40 CFR 1048.240 - How do I demonstrate that my engine family complies with exhaust emission standards?

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... significant figures, consistent with good engineering judgment. For example, your deterioration factors must... technology. Also, you may use an additive deterioration factor for exhaust emissions for a particular... pollutant and then add the results before rounding. (e) Use good engineering judgment to demonstrate...

  19. 40 CFR 1051.107 - What are the exhaust emission standards for all-terrain vehicles (ATVs) and offroad utility...

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... standards for all-terrain vehicles (ATVs) and offroad utility vehicles? 1051.107 Section 1051.107 Protection... are the exhaust emission standards for all-terrain vehicles (ATVs) and offroad utility vehicles? This... analyses. Survey data is allowed but not required to make this showing. [67 FR 68347, Nov. 8, 2002, as...

  20. 40 CFR 1051.107 - What are the exhaust emission standards for all-terrain vehicles (ATVs) and offroad utility...

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... standards for all-terrain vehicles (ATVs) and offroad utility vehicles? 1051.107 Section 1051.107 Protection... are the exhaust emission standards for all-terrain vehicles (ATVs) and offroad utility vehicles? This... analyses. Survey data is allowed but not required to make this showing. ...

  1. 40 CFR 1051.107 - What are the exhaust emission standards for all-terrain vehicles (ATVs) and offroad utility...

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... standards for all-terrain vehicles (ATVs) and offroad utility vehicles? 1051.107 Section 1051.107 Protection... are the exhaust emission standards for all-terrain vehicles (ATVs) and offroad utility vehicles? This... analyses. Survey data is allowed but not required to make this showing. ...

  2. 40 CFR 600.114-12 - Vehicle-specific 5-cycle fuel economy and carbon-related exhaust emission calculations.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 30 2014-07-01 2014-07-01 false Vehicle-specific 5-cycle fuel economy and carbon-related exhaust emission calculations. 600.114-12 Section 600.114-12 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) ENERGY POLICY FUEL ECONOMY AND GREENHOUSE GAS...

  3. Hanford Site radionuclide national emission standards for hazardous air pollutants unregistered stack (power exhaust) source assessment

    SciTech Connect

    Davis, W.E.

    1994-08-04

    On February 3, 1993, the US Department of Energy, Richland Operations Office received a Compliance Order and Information Request from the Director of the Air and Toxics Division of the US Environmental Protection Agency, Region 10. The Compliance Order requires the Richland Operations Office to evaluate all radionuclide emission points at the Hanford Site to determine which are subject to continuous emission measurement requirements in 40 Code of Federal Regulations (CFR) 61, Subpart H, and to continuously measure radionuclide emissions in accordance with 40 CFR 61.93. This evaluation provides an assessment of the 39 unregistered stacks, under Westinghouse Hanford Company`s management, and their potential radionuclide emissions, i.e., emissions with no control devices in place. The evaluation also determined if the effective dose equivalent from any of these stack emissions exceeded 0.1 mrem/yr, which will require the stack to have continuous monitoring. The result of this assessment identified three stacks, 107-N, 296-P-26 and 296-P-28, as having potential emissions that would cause an effective dose equivalent greater than 0.1 mrem/yr. These stacks, as noted by 40 CFR 61.93, would require continuous monitoring.

  4. 40 CFR 600.206-12 - Calculation and use of FTP-based and HFET-based fuel economy and carbon-related exhaust emission...

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... HFET-based fuel economy and carbon-related exhaust emission values for vehicle configurations. 600.206... POLICY FUEL ECONOMY AND CARBON-RELATED EXHAUST EMISSIONS OF MOTOR VEHICLES Fuel Economy Regulations for 1977 and Later Model Year Automobiles-Procedures for Calculating Fuel Economy Values §...

  5. 40 CFR 600.208-12 - Calculation of FTP-based and HFET-based fuel economy and carbon-related exhaust emission values...

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ...-based fuel economy and carbon-related exhaust emission values for a model type. 600.208-12 Section 600... ECONOMY AND CARBON-RELATED EXHAUST EMISSIONS OF MOTOR VEHICLES Fuel Economy Regulations for 1977 and Later Model Year Automobiles-Procedures for Calculating Fuel Economy Values § 600.208-12 Calculation of FTP...

  6. 40 CFR 600.113-12 - Fuel economy and carbon-related exhaust emission calculations for FTP, HFET, US06, SC03 and cold...

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ...-related exhaust emissions for electric vehicles, fuel cell vehicles and plug-in hybrid electric vehicles. Manufacturers shall determine carbon-related exhaust emissions for electric vehicles, fuel cell vehicles, and plug-in hybrid electric vehicles according to the provisions of this paragraph (m). Subject to the...

  7. Contactless electric igniter for vehicle to lower exhaust emission and fuel consumption.

    PubMed

    Shen, Chih-Lung; Su, Jye-Chau

    2014-01-01

    An electric igniter for engine/hybrid vehicles is presented. The igniter comprises a flyback converter, a voltage-stacked capacitor, a PIC-based controller, a differential voltage detector, and an ignition coil, of which structure is non-contact type. Since the electric igniter adopts a capacitor to accumulate energy for engine ignition instead of traditional contacttype approach, it enhances the igniting performance of a spark plug effectively. As a result, combustion efficiency is promoted, fuel consumption is saved, and exhaust emission is reduced. The igniter not only is good for fuel efficiency but also can reduce HC and CO emission significantly, which therefore is an environmentally friendly product. The control core of the igniter is implemented on a single chip, which lowers discrete component count, reduces system volume, and increases reliability. In addition, the ignition timing can be programmed so that a timing regulator can be removed from the proposed system, simplifying its structure. To verify the feasibility and functionality of the igniter, key waveforms are measured and real-car experiments are performed as well.

  8. Contactless Electric Igniter for Vehicle to Lower Exhaust Emission and Fuel Consumption

    PubMed Central

    Su, Jye-Chau

    2014-01-01

    An electric igniter for engine/hybrid vehicles is presented. The igniter comprises a flyback converter, a voltage-stacked capacitor, a PIC-based controller, a differential voltage detector, and an ignition coil, of which structure is non-contact type. Since the electric igniter adopts a capacitor to accumulate energy for engine ignition instead of traditional contacttype approach, it enhances the igniting performance of a spark plug effectively. As a result, combustion efficiency is promoted, fuel consumption is saved, and exhaust emission is reduced. The igniter not only is good for fuel efficiency but also can reduce HC and CO emission significantly, which therefore is an environmentally friendly product. The control core of the igniter is implemented on a single chip, which lowers discrete component count, reduces system volume, and increases reliability. In addition, the ignition timing can be programmed so that a timing regulator can be removed from the proposed system, simplifying its structure. To verify the feasibility and functionality of the igniter, key waveforms are measured and real-car experiments are performed as well. PMID:24672372

  9. Particulate matters from diesel heavy duty trucks exhaust versus cigarettes emissions: a new educational antismoking instrument.

    PubMed

    De Marco, Cinzia; Ruprecht, Ario Alberto; Pozzi, Paolo; Munarini, Elena; Ogliari, Anna Chiara; Mazza, Roberto; Boffi, Roberto

    2015-01-01

    Indoor smoking in public places and workplaces is forbidden in Italy since 2003, but some health concerns are arising from outdoor secondhand smoke (SHS) exposure for non-smokers. One of the biggest Italian Steel Manufacturer, with several factories in Italy and abroad, the Marcegaglia Group, recently introduced the outdoor smoking ban within the perimeter of all their factories. In order to encourage their smoker employees to quit, the Marcegaglia management decided to set up an educational framework by measuring the PM1, PM2.5 and PM10 emissions from heavy duty trucks and to compare them with the emissions of cigarettes in an indoor controlled environment under the same conditions. The exhaust pipe of two trucks powered by a diesel engine of about 13.000/14.000 cc(3) were connected with a flexible hose to a hole in the window of a container of 36 m(3) volume used as field office. The trucks operated idling for 8 min and then, after adequate office ventilation, a smoker smoked a cigarette. Particulate matter emission was thereafter analyzed. Cigarette pollution was much higher than the heavy duty truck one. Mean of the two tests was: PM1 truck 125.0(47.0), cigarettes 231.7(90.9) p = 0.002; PM2.5 truck 250.8(98.7), cigarettes 591.8(306.1) p = 0.006; PM10 truck 255.8(52.4), cigarettes 624.0(321.6) p = 0.002. Our findings may be important for policies that aim reducing outdoor SHS exposure. They may also help smokers to quit tobacco dependence by giving them an educational perspective that rebuts the common alibi that traffic pollution is more dangerous than cigarettes pollution.

  10. Investigation of PCDD/F emissions from mobile source diesel engines: impact of copper zeolite SCR catalysts and exhaust aftertreatment configurations.

    PubMed

    Liu, Z Gerald; Wall, John C; Barge, Patrick; Dettmann, Melissa E; Ottinger, Nathan A

    2011-04-01

    This study investigated the impact of copper zeolite selective catalytic reduction (SCR) catalysts and exhaust aftertreatment configurations on the emissions of polychlorinated dibenzo-p-dioxins (PCDDs) and polychlorinated dibenzofurans (PCDFs) from mobile source diesel engines. Emissions of PCDD/Fs, reported as the weighted sum of 17 congeners called the toxic equivalency quotient (TEQ), were measured using a modified EPA Method 0023A in the absence and presence of exhaust aftertreatment. Engine-out emissions were measured as a reference, while aftertreatment configurations included various combinations of diesel oxidation catalyst (DOC), diesel particulate filter (DPF), Cu-zeolite SCR, Fe-zeolite SCR, ammonia oxidation catalyst (AMOX), and aqueous urea dosing. In addition, different chlorine concentrations were evaluated. Results showed that all aftertreatment configurations reduced PCDD/F emissions in comparison to the engine-out reference, consistent with reduction mechanisms such as thermal decomposition or combined trapping and hydrogenolysis reported in the literature. Similarly low PCDD/F emissions from the DOC-DPF and the DOC-DPF-SCR configurations indicated that PCDD/F reduction primarily occurred in the DOC-DPF with no noticeable contribution from either the Cu- or Fe-zeolite SCR systems. Furthermore, experiments performed with high chlorine concentration provided no evidence that chlorine content has an impact on the catalytic synthesis of PCDD/Fs for the chlorine levels investigated in this study.

  11. An evaluation of the environmental and health effects of vehicle exhaust catalysts in the UK.

    PubMed Central

    Hutchinson, Emma J; Pearson, Peter J G

    2004-01-01

    Since 1993, all new gasoline-engine automobiles in the United Kingdom have been supplied with three-way vehicle exhaust catalytic converters (VECs) containing platinum, palladium, and rhodium, to comply with European Commission Stage I limits on emissions of regulated pollutants: carbon monoxide, hydrocarbons, and oxides of nitrogen. We conducted a physical and economic evaluation of the environmental and health benefits from a reduction in emissions through this mandated environmental technology against the costs, with reference to urban areas in Great Britain. We made both an ex post assessment--based on available data to 1998--and an ex ante assessment--projected to 2005, the year when full penetration of VECs into the fleet is expected. Substantial health benefits in excess of the costs of VECs were indicated: By 1998 the estimated net societal health benefits were approximately 500 million British pounds, and by 2005 they were estimated to rise to as much as 2 billion British pounds. We also found through environmental surveys that although lead in road dust has fallen by 50% in urban areas, platinum accumulations near roads have risen significantly, up to 90-fold higher than natural background levels. This rapid accumulation of platinum suggests further monitoring is warranted, although as yet there is no evidence of adverse health effects. PMID:14754566

  12. An evaluation of the environmental and health effects of vehicle exhaust catalysts in the UK.

    PubMed

    Hutchinson, Emma J; Pearson, Peter J G

    2004-02-01

    Since 1993, all new gasoline-engine automobiles in the United Kingdom have been supplied with three-way vehicle exhaust catalytic converters (VECs) containing platinum, palladium, and rhodium, to comply with European Commission Stage I limits on emissions of regulated pollutants: carbon monoxide, hydrocarbons, and oxides of nitrogen. We conducted a physical and economic evaluation of the environmental and health benefits from a reduction in emissions through this mandated environmental technology against the costs, with reference to urban areas in Great Britain. We made both an ex post assessment--based on available data to 1998--and an ex ante assessment--projected to 2005, the year when full penetration of VECs into the fleet is expected. Substantial health benefits in excess of the costs of VECs were indicated: By 1998 the estimated net societal health benefits were approximately 500 million British pounds, and by 2005 they were estimated to rise to as much as 2 billion British pounds. We also found through environmental surveys that although lead in road dust has fallen by 50% in urban areas, platinum accumulations near roads have risen significantly, up to 90-fold higher than natural background levels. This rapid accumulation of platinum suggests further monitoring is warranted, although as yet there is no evidence of adverse health effects.

  13. The impact of using biodiesel/marine gas oil blends on exhaust emissions from a stationary diesel engine.

    PubMed

    Karavalakis, G; Tzirakis, E; Mattheou, L; Stournas, S; Zannikos, F; Karonis, D

    2008-12-01

    The purpose of this work was to investigate the impact of marine gas oil (MGO)/biodiesel blends on the exhaust emissions and fuel consumption in a single cylinder, stationary, diesel engine. Three different origins of biodiesel were used as the blending feedstock with the reference MGO, at proportions of 5 and 10% by volume. Methyl esters were examined according to the automotive FAME standard EN 14214. The baseline MGO and biodiesel blends were examined according to ISO 8217:2005 specifications for the DMA category. Independently of the biodiesel used, a decrease of PM, HC, CO and CO(2) emissions was observed. Emissions of NO(x) were also lower with respect to MGO. This reduction in NO(x) may be attributed to some physicochemical properties of the fuels applied, such as the higher cetane number and the lower volatility of methyl esters. Reductions in PM for biodiesel blends were lower in the exhaust than those of the reference fuel which was attributed to the oxygen content and the near absence of sulphur and aromatics compounds in biodiesel. However, a slight increase in fuel consumption was observed for the biodiesel blends that may be tolerated due to the exhaust emissions benefits. Brake thermal efficiency was also determined. Unregulated emissions were characterized by determining the soluble organic fraction content of the particulate matter.

  14. Impact of methanol-gasoline fuel blend on the fuel consumption and exhaust emission of a SI engine

    NASA Astrophysics Data System (ADS)

    Rifal, Mohamad; Sinaga, Nazaruddin

    2016-04-01

    In this study, the effect of methanol-gasoline fuel blend (M15, M30 and M50) on the fuel consumption and exhaust emission of a spark ignition engine (SI) were investigated. In the experiment, an engine four-cylinder, four stroke injection system (engine of Toyota Kijang Innova 1TR-FE) was used. Test were did to know the relation of fuel consumption and exhaust emission (CO, CO2, HC) were analyzed under the idle throttle operating condition and variable engine speed ranging from 1000 to 4000 rpm. The experimental result showed that the fuel consumption decrease with the use of methanol. It was also shown that the CO and HC emission were reduced with the increase methanol content while CO2 were increased.

  15. A comparative study of the elemental composition of the exhaust emissions of cars powered by liquefied petroleum gas and unleaded petrol

    NASA Astrophysics Data System (ADS)

    Lim, McKenzie C. H.; Ayoko, Godwin A.; Morawska, Lidia; Ristovski, Zoran D.; Jayaratne, E. Rohan; Kokot, Serge

    Elements emitted from the exhausts of new Ford Falcon Forte cars powered by unleaded petrol (ULP) and liquefied petroleum gas (LPG) were measured on a chassis dynamometer. The measurements were carried out in February, June and August 2001, and at two steady state driving conditions (60 and 80 km h -1). Thirty seven elements were quantified in the exhaust samples by inductively coupled plasma mass spectrometry (ICPMS). The total emission factors of the elements from the exhausts of ULP cars were higher than those of LPG cars at both engine speeds even though high variability in the exhaust emissions from different cars was noted. The effect of the operating conditions such as mileage of the cars, engine speed, fuel and lubricating oil compositions on the emissions was studied. To investigate the effects of these conditions, multivariate data analysis methods were employed including exploratory principal component analysis (PCA), and the multi-criteria decision making methods (MCDM), preference ranking organization method for enrichment evaluation (PROMETHEE) and geometrical analysis for interactive aid (GAIA), for ranking the cars on the basis of the emission factors of the elements. PCA biplot of the complete data matrix showed a clear discrimination of the February, June and August emission test results. In addition, (i) platinum group elements (PGE) emissions were separated from each other in the three different clusters viz. Pt with February, Pd with June and Rh with August; (ii) the motor oil related elements, Zn and P, were particularly associated with the June and August tests (these vectors were also grouped with V, Al and Cu); and (iii) highest emissions of most major elements were associated with the August test after the cars have recorded their highest mileage. Extensive analysis with the aid of the MCDM ranking methods demonstrated clearly that cars powered by LPG outperform those powered by ULP. In general, cars tested in June perform better than

  16. Unregulated gaseous exhaust emission from modern ethanol fuelled light duty vehicles in cold ambient condition

    NASA Astrophysics Data System (ADS)

    Clairotte, M.; Adam, T. W.; Zardini, A. A.; Astorga, C.

    2011-12-01

    According to Directive 2003/30/EC and 2009/28/EC of the European Parliament and the Council, Member States should promote the use of biofuel. Consequently, all petrol and diesel used for transport purpose available on the market since the 1st of January 2011 must contain a reference value of 5.75% of renewable energy. Ethanol in gasoline could be a promising alternative to comply with this objective, and is actually available in higher proportion in Sweden and Brazil. In addition to a lower dependence on fossil fuel, it is well established that ethanol contributes to reduce air pollutant emissions during combustion (CO, THC), and presents a beneficial effect on the greenhouse gas emissions. However, these statements rely on numerous chassis dynamometer emission studies performed in warm condition (22°C), and very few emission data are available at cold ambient condition encountered in winter, particularly in the north of Europe. In this present study, the effects of ethanol (E75-E85) versus gasoline (E5) have been investigated at cold ambient temperature (-7°C). Experiments have been carried out in a chassis dynamometer at the Vehicle Emission Laboratory (VELA) of the European Commission's Joint Research Centre (JRC - Ispra, Italy). Emissions of modern passenger cars complying with the latest European standard (Euro4 and Euro5a) were tracked over the New European Driving Cycle (NEDC). Unregulated gaseous compounds like greenhouse gases (carbon dioxide, methane, nitrous oxide), and air quality related compounds (ammonia, formaldehyde, acetaldehyde) were monitored by an online Fourier Transformed Infra-Red spectrometer with 1 Hz acquisition frequency. In addition, a number of ozone precursors (carbonyls and volatile organic hydrocarbons) were collected in order to assess the ozone formation potential (OFP) of the exhaust. Results showed higher unregulated emissions at -7°C, regardless of the ethanol content in the fuel blend. Most of the emissions occurred during

  17. Numerical investigation of exhaust gas emissions for a dual fuel engine configuration using diesel and pongamia oil.

    PubMed

    Mohamed Ibrahim, N H; Udayakumar, M

    2016-12-01

    The investigation presented in this paper focuses on determination of gaseous exhaust emissions by computational simulation during combustion in compression ignition engine with pongamia oil substitution. Combustion is modeled using Equilibrium Constants Method (ECM) with MATLAB program to calculate the mole fraction of 10 combustion products when pongamia oil is burnt along with diesel at variable equivalence ratio and blend ratio. It had been observed that pongamia oil substitution causes decrease in the CO emission and increase in the NOx emission as the blend ratio as well as equivalence ratio increases.

  18. Trends in exhaust emissions from in-use Mexico City vehicles, 2000-2006. A remote sensing study.

    PubMed

    Schifter, I; Díaz, L; Rodríguez, R; Durán, J; Chávez, O

    2008-02-01

    A remote sensing study was conducted in year 2006 in four locations of the Metropolitan Area of Mexico City (MAMC). Two of the sites were the same studied back by us in year 2000 and by others in year 1994. A database was compiled containing 11,289 valid measurements for the carbon monoxide (CO), total hydrocarbons (THC), and nitric oxide (NO) exhaust vehicles emissions. Valid measurements were binned for each pollutant by the vehicle specific power (between -5 and 20 kW tonne(-1)) for the 2000 and 2006 databases. The mean average CO, THC, and NO emissions for year 2006 were determined to be 1.10 +/- 0.18 vol.%, 299 +/- 88.4 ppm, and 610 +/- 115.0 ppm, respectively. Matching the vehicle driving patterns of the fleet measured in year 2000 with the emissions factors obtained in this work, allows estimating the trends in the exhaust emissions of vehicles in the MAMC. The adjusted results of the remote sensing study performed in year 2006 shows that the fleet has decrease 22% in CO and 17% in NO emissions, with small change in total hydrocarbons emissions. The improvements could be related with the introduction in year 2001 of vehicles that met tighter emissions standards, particularly for nitrogen oxides.

  19. Importance of automobile exhaust catalyst emissions for the deposition of platinum, palladium, and rhodium in the northern hemisphere.

    PubMed

    Rauch, Sebastien; Hemond, Harold F; Barbante, Carlo; Owari, Masanori; Morrison, Gregory M; Peucker-Ehrenbrink, Bernhard; Wass, Urban

    2005-11-01

    An estimated 500 million vehicles worldwide are equipped with an exhaust catalyst that uses platinum group elements (PGE) as the main active components and thus contribute to global PGE emissions. Although PGE emitted from automobile exhaust catalysts were first believed to remain in the roadside environment, we propose here that fine PGE-containing particles in automobile exhaust have resulted in a widespread distribution of emitted PGE. Regional and long-range transport of PGE from automobile exhaust catalysts is supported by elevated PGE deposition in both a peat bog located 250 m from traffic and in central Greenland, respectively. Russian smelters were also found to contribute to PGE contamination in central Greenland. Deposition rates estimated for the roadside environment, the peat bog, and central Greenland were used to provide a first estimate of PGE deposition in the northern hemisphere. The results show that deposition of regionally or long-range transported PGE accounts for a large fraction of total PGE deposition, and PGE deposition in the roadside environment represents less than 5% of the total deposition. Transport at the regional and global scales represents an important component in the environmental cycle of emitted PGE and needs to be further studied to fully assess the environmental fate of PGE from automobile exhaust catalysts.

  20. Vehicle emission sensing and evaluation using the Smog Dog in Houston

    NASA Astrophysics Data System (ADS)

    Yu, Lei; Burrier, Stanley W.

    1997-02-01

    The advanced remote vehicle emission sensing equipment, Smog Dog, is a cost-effective infrared technology designed to measure the levels of vehicle exhaust. This paper presents and demonstrates a research effort for using the Smog Dog to conduct the on-road vehicle exhaust emission collection in the city of Houston, develop modal sensitive emission models and evaluate the EPA approved MOBILE5A emission factor model. The vehicle emission data collection is designed in a manner that various vehicle's modal events such as the acceleration and deceleration under the on-road driving conditions are considered. The Smog Dog remote mission sensor can not only collect the emission concentrations of hydrocarbon, carbon monoxide and oxide of nitrogen but also simultaneously detect the vehicles' instantaneous speeds and acceleration rates. Thus a vehicle's emission rates, which are converted from the collected emission concentration levels, can be functions of its instantaneous speed and acceleration rate. In addition, the Federal Test Procedure driving cycles are emulated using the emission versus speed profile relationships and the resulted emission rate for a predetermined average driving speed can then be compared with the emission factors produced by MOBILE5A. Since the emission models, that are developed based on the on-road emission data collected using the Smog Dog, naturally reflect the on-road driving conditions and the vehicle fleet combinations, they can potentially be used to evaluate the vehicle exhaust emission implications of various advanced traffic management strategies.

  1. Exhaust Fine Particle and Nitrogen Oxide Emissions from Individual Heavy-Duty Trucks at the Port of Oakland

    NASA Astrophysics Data System (ADS)

    Dallmann, T. R.; Harley, R. A.; Kirchstetter, T.

    2010-12-01

    Heavy-duty (HD) diesel trucks are a source of nitrogen oxide (NOx) emissions as well as primary fine particulate matter (PM2.5) that includes black carbon (BC) as a major component. Heavy-duty trucks contribute significantly to elevated levels of diesel particulate matter found near highways and in communities surrounding major freight-handling facilities. To reduce the air quality impact of diesel engine emissions, the California Air Resources Board has adopted new rules requiring the retrofit or replacement of in-use HD trucks. These rules take effect during 2010 at ports and railyards, and apply to all trucks operating in California by 2014. This study involves on-road measurements of PM2.5, BC, and NOx emission factor distributions from individual HD trucks driving into the Port of Oakland in the San Francisco Bay area. Measurements of exhaust plumes from individual trucks were made using a mobile laboratory equipped with fast time response (1 Hz) PM2.5, BC, NOx, and carbon dioxide (CO2) sensors. The mobile laboratory was stationed on an overpass above an arterial roadway that connects the Port to a nearby highway (I-880). The air sampling inlet was thereby located above the vertical exhaust pipes of HD diesel trucks passing by on the arterial roadway below. Fuel-specific PM2.5, BC, and NOx emission factors for individual trucks were calculated using a carbon balance method in which concentrations of these species in an exhaust plume are normalized to CO2 concentrations. Initial field sampling was conducted in November, 2009 prior to the implementation of new emission rules. Additional emission measurements were made at the same location during June 2010 and emission factor distributions and averages will be compared.

  2. A comprehensive inventory of the ship traffic exhaust emissions in the Baltic Sea from 2006 to 2009.

    PubMed

    Jalkanen, Jukka-Pekka; Johansson, Lasse; Kukkonen, Jaakko

    2014-04-01

    This study addresses the exhaust emissions of CO₂, NO(x), SO(x), CO, and PM(2.5) originated from Baltic Sea shipping in 2006-2009. Numerical results have been computed using the Ship Traffic Emissions Assessment Model. This model is based on the messages of the automatic identification system (AIS), which enable the positioning of ships with a high spatial resolution. The NO(x) emissions in 2009 were approximately 7 % higher than in 2006, despite the economic recession. However, the SO(x) emissions in 2009 were approximately 14 % lower, when compared to those in 2006, mainly caused by the fuel requirements of the SO(x) emission control area (SECA) which became effective in May 2006, but affected also by changes in ship activity. Results are presented on the differential geographic distribution of shipping emissions before (Jan-April 2006) and after (Jan-April 2009) the SECA regulations. The predicted NO(x) emissions in 2009 substantially exceeded the emissions in 2006 along major ship routes and at numerous harbors, mostly due to the continuous increase in the number of small vessels that use AIS transmitters. Although the SO(x) emissions have been reduced in 2009 in most major ship routes, these have increased in the vicinity of some harbors and on some densely trafficked routes. A seasonal variation of emissions is also presented, as well as the distribution of emissions in terms of vessel flag state, type, and weight.

  3. Evaluation of Partial Oxidation Reformer Emissions

    SciTech Connect

    Unnasch, Stefan; Fable, Scott; Waterland, Larry

    2006-01-06

    In this study, a gasoline fuel processor and an ethanol fuel processor were operated under conditions simulating both startup and normal operation. Emissions were measured before and after the AGB in order to quantify the effectiveness of the burner catalyst in controlling emissions. The emissions sampling system includes CEM for O2, CO2, CO, NOx, and THC. Also, integrated gas samples are collected in evacuated canisters for hydrocarbon speciation analysis via GC. This analysis yields the concentrations of the hydrocarbon species required for the California NMOG calculation. The PM concentration in the anode burner exhaust was measured through the placement of a filter in the exhaust stream. The emissions from vehicles with fully developed on board reformer systems were estimated.

  4. Study of exhaust emissions from 1978-1980 model year three way catalyst vehicles in Los Angeles. Final report

    SciTech Connect

    Moore, L.L.; Jones, A.D.

    1980-03-01

    This report presents and summarizes exhaust emission data and other information obtained as a result of the testing and inspection of 350 in-use passenger cars. The test fleet was made up of 1978, 1979 and 1980 automobiles manufactured by Ford, General Motors, Mazda, Saab, Toyota, Volkswagen/Audi and Volvo. Each vehicle was equipped with a three way catalyst control system. They were obtained randomly from private owners in the Los Angeles and Orange County areas. The testing was completed December, 1979. Each vehicle was tested only in as-received condition. The test sequence consisted of the 1975 Federal Test Procedure (exhaust emissions only), a Highway Fuel Economy test, a Two-Speed Idle test, a Federal Three Mode test, and a Loaded Two Mode test. After the initial test sequence, each vehicle was subjected to a thorough underhood inspection.

  5. Real-world fuel efficiency and exhaust emissions of light-duty diesel vehicles and their correlation with road conditions.

    PubMed

    Hu, Jingnan; Wu, Ye; Wang, Zhishi; Li, Zhenhua; Zhou, Yu; Wang, Haitao; Bao, Xiaofeng; Hao, Jiming

    2012-01-01

    The real-world fuel efficiency and exhaust emission profiles of CO, HC and NOx for light-duty diesel vehicles were investigated. Using a portable emissions measurement system, 16 diesel taxies were tested on different roads in Macao and the data were normalized with the vehicle specific power bin method. The 11 Toyota Corolla diesel taxies have very good fuel economy of (5.9 +/- 0.6) L/100 km, while other five diesel taxies showed relatively high values at (8.5 +/- 1.7) L/100 km due to the variation in transmission systems and emission control strategies. Compared to similar Corolla gasoline models, the diesel cars confirmed an advantage of ca. 20% higher fuel efficiency. HC and CO emissions of all the 16 taxies are quite low, with the average at (0.05 +/- 0.02) g/km and (0.38 +/- 0.15) g/km, respectively. The average NOx emission factor of the 11 Corolla taxies is (0.56 +/- 0.17) g/km, about three times higher than their gasoline counterparts. Two of the three Hyundai Sonata taxies, configured with exhaust gas recirculation (EGR) + diesel oxidation catalyst (DOC) emission control strategies, indicated significantly higher NO2 emissions and NO2/NOx ratios than other diesel taxies and consequently trigger a concern of possibly adverse impacts on ozone pollution in urban areas with this technology combination. A clear and similar pattern for fuel consumption and for each of the three gaseous pollutant emissions with various road conditions was identified. To save energy and mitigate CO2 emissions as well as other gaseous pollutant emissions in urban area, traffic planning also needs improvement.

  6. Gas-solid chromatographic analysis of automobile tailpipe emissions as a function of different engine and exhaust system modifications

    SciTech Connect

    Kang, L.; Armstrong, D.W.

    1994-12-31

    The authors developed a single, relatively short gas-solid chromatographic PLOT column and used it to separate aliphatic hydrocarbons, aromatic hydrocarbons and some inorganic gases (O{sub 2}, N{sub 2}, CO and CO{sub 2}) found in automobile exhaust. In the case of hydrocarbons, both aliphatic and aromatic components (up through alkylated-benzenes) were done in one run. Subambient temperature was needed for the oxygen-nitrogen separation, but they were easily resolved from each other and the other compounds present. The effects of different engine and exhaust system modifications on the level of compounds in the exhaust were tested. The concentrations of the emission gases varied considerably with changes in air/fuel ratio, coil voltage, use of catalytic converters and so forth. The results showed that the use of catalytic converter and a higher voltage coil tended to produce the most pronounced decreases in emissions of hydrocarbons and the catalytic converter produced the significant decrease in carbon monoxide concentrations. The results of the GSC analyses were compared to those of a commercial emission analyzer (i.e., sniffer). They showed similar trends and relative concentrations but somewhat different absolute concentrations. This may have been due to differences in the calibration of these methods.

  7. Baseline Exhaust Emissions from U. S. Army M54A2 LDS 465 Powered Five-Ton Trucks.

    DTIC Science & Technology

    DIESEL ENGINES, *EXHAUST GASES), (*AIR POLLUTION, EXHAUST GASES), (*ODORS, EXHAUST GASES), CARGO VEHICLES, SMOKE, HYDROCARBONS, CARBON MONOXIDE, CARBON DIOXIDE, NITROGEN OXIDES, SULFUR COMPOUNDS, ALDEHYDES, TEST METHODS

  8. 40 CFR 600.113-12 - Fuel economy and carbon-related exhaust emission calculations for FTP, HFET, US06, SC03 and cold...

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 29 2010-07-01 2010-07-01 false Fuel economy and carbon-related... ECONOMY AND CARBON-RELATED EXHAUST EMISSIONS OF MOTOR VEHICLES Fuel Economy Regulations for 1978 and Later Model Year Automobiles-Test Procedures § 600.113-12 Fuel economy and carbon-related exhaust...

  9. Influences of vehicles’ fuel consumption and exhaust emissions on the trip cost without late arrival under car-following model

    NASA Astrophysics Data System (ADS)

    Tang, Tie-Qiao; Yu, Qiang

    2016-07-01

    In this paper, we use car-following model to explore the influences of the vehicle’s fuel consumption and exhaust emissions on each commuter’s trip cost without late arrival on one open road. Our results illustrate that considering the vehicle’s fuel cost and emission cost only enhances each commuter’s trip cost and the system’s total cost, but has no prominent impacts on his optimal time headway at the origin of each open road under the minimum total cost.

  10. Evaluation of Federal Aviation Administration Engine Exhaust Sampling Rake.

    DTIC Science & Technology

    1977-06-01

    Hydrocarbon Emissions for the Vorbix Obtained With Different Sampling Probes 29 22 Affect of Sampling Rake on Engine Performance 30 v ~’ -V 4 ~ V...measurable tailpipe blockage and comequent engine performance shifts. The performance shifts had negligible affect on setting enge conditions and did...11.76 FAA MAKE (0 M~S-9C I I SI NO RAKE I1100 .120 1340 1300 1380 1400 1420 1.44D 1410 1.40 ENGINEG PRESSURE RATIO PT7/PT2 p9gur 22 Affect of SamplingRake

  11. Current and future emission estimates of exhaust gases and particles from shipping at the largest port in Korea.

    PubMed

    Song, Sang-Keun; Shon, Zang-Ho

    2014-05-01

    The emissions of exhaust gases (NOx , SO2, VOCs, and CO2) and particles (e.g., PM) from ships traversing Busan Port in Korea were estimated over three different years (the years 2006, 2008, and 2009). This analysis was performed according to the ship operational modes ("at sea," "maneuvering," and "in port") and ship types based on an activity-based method. The ship emissions for current (base year 2009) and future scenarios (years 2020 and 2050) were also compared. The annual emissions of SO2, VOCs, PM, and CO2 were highest (9.6 × 10(3), 374, 1.2 × 10(3), and 5.6 × 10(5) ton year(-1), respectively) in 2008. In contrast, the annual NO x emissions were highest (11.7 × 10(3) ton year(-1)) in 2006 due mainly to the high NO x emission factor. The emissions of air pollutants for each ship operational mode differed considerably, with the largest emission observed in "in port" mode. In addition, the largest fraction (approximately 45-67%) of the emissions of all air pollutants during the study period was emitted from container ships. The future ship emissions of most pollutants (except for SO2 and PM) in 2020 and 2050 are estimated to be 1.4-1.8 and 4.7-6.1 times higher than those in 2009 (base year), respectively.

  12. Exhaust emissions of polycyclic aromatic hydrocarbons, n-alkanes and phenols from vehicles coming within different European classes

    NASA Astrophysics Data System (ADS)

    Perrone, Maria Grazia; Carbone, Claudio; Faedo, Davide; Ferrero, Luca; Maggioni, Angela; Sangiorgi, Giorgia; Bolzacchini, Ezio

    2014-01-01

    EU emission standards for vehicles do not include many particulate (PM) and gaseous species, despite their considerable impact on air pollution and health. Emission factors (EFs) were measured for unregulated species, i.e. polycyclic aromatic hydrocarbons (PAHs) and n-alkanes (ALKs) in the particle phase, and, for the first time, EFs for phenols in both particle and gas phases. Exhaust samples were collected under controlled operating conditions (chassis dynamometer tests) for in-service vehicles (private cars, PCs and light duty vehicles, LDVs) from different EURO classes. EFs of trace organics were highest for the old EURO 1 vehicles (the tested EURO 1 vehicles were without emission-control devices), and lowest for the more recent EURO 3 and 4 vehicles. ALKs (C20-C32) were the most abundant trace organic compounds found in PM vehicle exhaust, and their EF ranged between 2034 and 101 μg km-1 (Euro 1-4 LDVs). PM-phased phenols EFs were in the range 0.42-2.50 μg km-1, and 4-nitrophenol was the most abundant one. The highest EFs were measured for phenols in the gas phase (dominated by the presence of phenol) for gasoline EURO 1 (43.16 ± 9.99 μg km-1). Emissions of PAHs changed depending on the fuel used. The PAH EFs of diesel-driven PCs were 4-5 times higher than those of gasoline vehicles, with PAHs diesel exhaust being mainly enriched in low 4-ring PAHs (85%), while 5-6 ring PAHs were prevalent (55%) in gasoline vehicles. Results of source profiles from chassis dynamometer tests were compared with ambient data, and the traffic PAH source profile derived from a tunnel study (Milan) agreed with the estimated emissions from a mix of diesel and gasoline vehicles circulating in the same area. Moreover, the impact of EURO regulatory changes on exhaust emissions was calculated, and this made it possible to estimate the downward trend of PAH emissions in the Province of Milan in the period 2005-2020.

  13. Extrapolating Ground-Based Aircraft Engine Exhaust Emissions to Cruise Conditions: Lessons From the 2013 ACCESS Chase Plane Experiment

    NASA Astrophysics Data System (ADS)

    Moore, R.; Shook, M.; Thornhill, K. L.; Winstead, E.; Anderson, B. E.

    2013-12-01

    Aircraft engine emissions constitute a tiny fraction of the global black carbon mass, but can have a disproportionate climatic impact because they are emitted high in the troposphere and in remote regions with otherwise low aerosol concentrations. Consequently, these particles are likely to strongly influence cirrus and contrail formation by acting as ice nuclei (IN). However, the ice nucleating properties of aircraft exhaust at relevant atmospheric conditions are not well known, and thus, the overall impact of aviation on cloud formation remains very uncertain. While a number of aircraft engine emissions studies have previously been conducted at sea level temperature and pressure (e.g., APEX, AAFEX-1 and 2), it unclear the extent to which exhaust emissions on the ground translate to emissions at cruise conditions with much lower inlet gas temperatures and pressures. To address this need, the NASA Alternative Fuel Effects on Contrails and Cruise Emissions (ACCESS) was conducted in February-April, 2013 to examine the aerosol and gas emissions from the NASA DC-8 under a variety of different fuel types, engine power, and altitude/meteorological conditions. Two different fuel types were studied: a traditional JP-8 fuel and a 50:50 blend of JP-8 and a camelina-based hydro-treated renewable jet (HRJ) fuel. Emissions were sampled using a comprehensive suite of gas- and aerosol-phase instrumentation integrated on an HU-25 Falcon jet that was positioned in the DC-8 exhaust plume at approximately 100-500m distance behind the engines. In addition, a four-hour ground test was carried out with sample probes positioned at 30 m behind each of the inboard engines. Measurements of aerosol concentration, size distribution, soot mass, and hygroscopicity were carried out along with trace gas measurements of CO2, NO, NO2, O3, and water vapor. NOx emissions were reconciled by employing the well-established Boeing method for normalizing engine fuel flow rates to STP; however, comparison

  14. Extrapolating Ground-Based Aircraft Engine Exhaust Emissions to Cruise Conditions: Lessons From the 2013 ACCESS Chase Plane Experiment

    NASA Astrophysics Data System (ADS)

    Moore, R.; Shook, M.; Thornhill, K. L.; Winstead, E.; Anderson, B. E.

    2011-12-01

    Aircraft engine emissions constitute a tiny fraction of the global black carbon mass, but can have a disproportionate climatic impact because they are emitted high in the troposphere and in remote regions with otherwise low aerosol concentrations. Consequently, these particles are likely to strongly influence cirrus and contrail formation by acting as ice nuclei (IN). However, the ice nucleating properties of aircraft exhaust at relevant atmospheric conditions are not well known, and thus, the overall impact of aviation on cloud formation remains very uncertain. While a number of aircraft engine emissions studies have previously been conducted at sea level temperature and pressure (e.g., APEX, AAFEX-1 and 2), it unclear the extent to which exhaust emissions on the ground translate to emissions at cruise conditions with much lower inlet gas temperatures and pressures. To address this need, the NASA Alternative Fuel Effects on Contrails and Cruise Emissions (ACCESS) was conducted in February-April, 2013 to examine the aerosol and gas emissions from the NASA DC-8 under a variety of different fuel types, engine power, and altitude/meteorological conditions. Two different fuel types were studied: a traditional JP-8 fuel and a 50:50 blend of JP-8 and a camelina-based hydro-treated renewable jet (HRJ) fuel. Emissions were sampled using a comprehensive suite of gas- and aerosol-phase instrumentation integrated on an HU-25 Falcon jet that was positioned in the DC-8 exhaust plume at approximately 100-500m distance behind the engines. In addition, a four-hour ground test was carried out with sample probes positioned at 30 m behind each of the inboard engines. Measurements of aerosol concentration, size distribution, soot mass, and hygroscopicity were carried out along with trace gas measurements of CO2, NO, NO2, O3, and water vapor. NOx emissions were reconciled by employing the well-established Boeing method for normalizing engine fuel flow rates to STP; however, comparison

  15. An Evaluation of a Welding Fumes Exhaust System. Agricultural Experiment Station Research Report 284.

    ERIC Educational Resources Information Center

    Jacobs, C. O.

    A study evaluated the feasibility of introducing unheated outside air into the airstream of a cross-flow welding exhaust system to reduce heating energy costs of a school welding laboratory. The physical facility used was the agricultural mechanics laboratory at the University of Arizona, which is similar to facilities in which instruction in…

  16. An Evaluation of a Welding Fumes Exhaust System. Agricultural Experiment Station Research Report 284.

    ERIC Educational Resources Information Center

    Jacobs, C. O.

    A study evaluated the feasibility of introducing unheated outside air into the airstream of a cross-flow welding exhaust system to reduce heating energy costs of a school welding laboratory. The physical facility used was the agricultural mechanics laboratory at the University of Arizona, which is similar to facilities in which instruction in…

  17. 340 vault K1 exhaust system HEPA filter evaluation

    SciTech Connect

    Arndt, T.E., Fluor Daniel Hanford

    1997-02-01

    A previous evaluation documented in report WHC-SD-GN-RPT-30005, Rev. 0, titled ``Evaluation on Self-Contained High Efficiency Particulate Filters,`` revealed that the SCHEPA filters do not have required documentation to be in compliance with the design, testing, and fabrication standards required in ASME N-509, ASME N-510, and MIL-F-51068. These standards are required by DOE Order 6430.IA. Without this documentation, filter adequacy cannot be verified. The existing SCHEPA filters can be removed and replaced with new filters and filter housing which meet current codes and standards.

  18. Single Particle Source Profiles of Gasoline and Diesel Powered Vehicles, Biomass Burning and Coal Combustion Exhaust Emissions

    NASA Astrophysics Data System (ADS)

    Suess, D. T.; Prather, K. A.; Schauer, J.; Cass, G. R.

    2001-12-01

    Vehicular exhaust, biomass burning, and coal combustion are three significant aerosol sources that have local to global impacts on the earth's atmosphere. They may also contribute to health effects as they can emit carcinogenic species such as polycyclic aromatic hydrocarbons (PAH) and trace metals including beryllium and vanadium. In these source characterization studies, combustion products were diluted to near ambient temperature and pressure using a two stage dilution source sampler. Diluted exhaust emissions were analyzed with an aerosol time-of-flight mass spectrometer (ATOFMS) obtaining real-time measurements of single particle size and chemical composition. In addition, samples were collected using a micro-orifice uniform deposit impactor (MOUDI), which was operated in a manner compatible with advanced chemical analysis techniques, for size segregated mass concentrations. Due to the importance of these particle sources to the atmosphere, differentiating these emissions from each other and other particle sources is essential. Since ATOFMS is a relatively new single particle analysis technique, source characterization experiments are needed to determine qualitative signatures of specific particulate sources for their ambient identification. ATOFMS single particle mass spectra will be discussed introducing chemically distinct single particle types emitted from these combustion sources. Numerous particle types are emitted from each source, as indicated by distinct chemical associations on the single particle level. Examples include, the chemical associations of vanadium with organic carbon (OC) in gasoline powered vehicle emissions, calcium with black carbon (BC) in diesel powered vehicle emissions, beryllium and boron with BC in coal combustion emissions, and potassium with OC from biomass burning emissions. Most importantly, the overall particle type distributions from each source differ significantly. Finally, complementary MOUDI mass distribution data will

  19. The 1977 emissions inventory for southeastern Virginia. [environment model of air quality based on exhaust emission from urban areas

    NASA Technical Reports Server (NTRS)

    Brewer, D. A.; Remsberg, E. E.; Woodbury, G. E.; Quinn, L. C.

    1979-01-01

    Regional tropospheric air pollution modeling and data compilation to simulate the time variation of species concentrations in and around an urban area is discussed. The methods used to compile an emissions inventory are outlined. Emissions factors for vehicular travel in the urban area are presented along with an analysis of the emission gases. Emission sources other than vehicular including industrial wastes, residential solid waste disposal, aircraft emissions, and emissions from the railroads are investigated.

  20. Exhaust particle and NOx emission performance of an SCR heavy duty truck operating in real-world conditions

    NASA Astrophysics Data System (ADS)

    Saari, Sampo; Karjalainen, Panu; Ntziachristos, Leonidas; Pirjola, Liisa; Matilainen, Pekka; Keskinen, Jorma; Rönkkö, Topi

    2016-02-01

    Particle and NOx emissions of an SCR equipped HDD truck were studied in real-world driving conditions using the "Sniffer" mobile laboratory. Real-time CO2 measurement enables emission factor calculation for NOx and particles. In this study, we compared three different emission factor calculation methods and characterised their suitability for real-world chasing experiments. The particle number emission was bimodal and dominated by the nucleation mode particles (diameter below 23 nm) having emission factor up to 1 × 1015 #/kgfuel whereas emission factor for soot (diameter above 23 nm that is consistent with the PMP standard) was typically 1 × 1014 #/kgfuel. The effect of thermodenuder on the exhaust particles indicated that the nucleation particles consisted mainly of volatile compounds, but sometimes there also existed a non-volatile core. The nucleation mode particles are not controlled by current regulations in Europe. However, these particles consistently form under atmospheric dilution in the plume of the truck and constitute a health risk for the human population that is exposed to those. Average NOx emission was 3.55 g/kWh during the test, whereas the Euro IV emission limit over transient testing is 3.5 g NOx/kWh. The on-road emission performance of the vehicle was very close to the expected levels, confirming the successful operation of the SCR system of the tested vehicle. Heavy driving conditions such as uphill driving increased both the NOx and particle number emission factors whereas the emission factor for soot particle number remains rather constant.

  1. Identification of lubrication oil in the particulate matter emissions from engine exhaust of in-service commercial aircraft.

    PubMed

    Yu, Zhenhong; Herndon, Scott C; Ziemba, Luke D; Timko, Michael T; Liscinsky, David S; Anderson, Bruce E; Miake-Lye, Richard C

    2012-09-04

    Lubrication oil was identified in the organic particulate matter (PM) emissions of engine exhaust plumes from in-service commercial aircraft at Chicago Midway Airport (MDW) and O'Hare International Airport (ORD). This is the first field study focused on aircraft lubrication oil emissions, and all of the observed plumes described in this work were due to near-idle engine operations. The identification was carried out with an Aerodyne high-resolution time-of-flight aerosol mass spectrometer (HR-ToF AMS) via a collaborative laboratory and field investigation. A characteristic mass marker of lubrication oil, I(85)/I(71), the ratio of ion fragment intensity between m/z = 85 and 71, was used to distinguish lubrication oil from jet engine combustion products. This AMS marker was based on ion fragmentation patterns measured using electron impact ionization for two brands of widely used lubrication oil in a laboratory study. The AMS measurements of exhaust plumes from commercial aircraft in this airport field study reveal that lubrication oil is commonly present in organic PM emissions that are associated with emitted soot particles, unlike the purely oil droplets observed at the lubrication system vent. The characteristic oil marker, I(85)/I(71), was applied to quantitatively determine the contribution from lubrication oil in measured aircraft plumes, which ranges from 5% to 100%.

  2. 40 CFR 1051.103 - What are the exhaust emission standards for snowmobiles?

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... emission standards even if its family emission limit is higher than the standard, as long as you show that...) Natural gas-fueled snowmobiles: NMHC emissions. (2) Alcohol-fueled snowmobiles: THCE emissions. (3) Other... comes first. You must specify a longer useful life in terms of kilometers and hours for the engine...

  3. 40 CFR 1051.103 - What are the exhaust emission standards for snowmobiles?

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... emission standards even if its family emission limit is higher than the standard, as long as you show that...) Natural gas-fueled snowmobiles: NMHC emissions. (2) Alcohol-fueled snowmobiles: THCE emissions. (3) Other... comes first. You must specify a longer useful life in terms of kilometers and hours for the engine...

  4. Ice-nucleating particle emissions from photochemically aged diesel and biodiesel exhaust

    NASA Astrophysics Data System (ADS)

    Schill, G. P.; Jathar, S. H.; Kodros, J. K.; Levin, E. J. T.; Galang, A. M.; Friedman, B.; Link, M. F.; Farmer, D. K.; Pierce, J. R.; Kreidenweis, S. M.; DeMott, P. J.

    2016-05-01

    Immersion-mode ice-nucleating particle (INP) concentrations from an off-road diesel engine were measured using a continuous-flow diffusion chamber at -30°C. Both petrodiesel and biodiesel were utilized, and the exhaust was aged up to 1.5 photochemically equivalent days using an oxidative flow reactor. We found that aged and unaged diesel exhaust of both fuels is not likely to contribute to atmospheric INP concentrations at mixed-phase cloud conditions. To explore this further, a new limit-of-detection parameterization for ice nucleation on diesel exhaust was developed. Using a global-chemical transport model, potential black carbon INP (INPBC) concentrations were determined using a current literature INPBC parameterization and the limit-of-detection parameterization. Model outputs indicate that the current literature parameterization likely overemphasizes INPBC concentrations, especially in the Northern Hemisphere. These results highlight the need to integrate new INPBC parameterizations into global climate models as generalized INPBC parameterizations are not valid for diesel exhaust.

  5. General Motors Corporation and Pacific Northwest Laboratory Staff Exchange: Instrumentation for rapid measurement of automotive exhaust emissions

    SciTech Connect

    Griffin, J.W.; Sharpe, S.W.; Sloane, T.M.

    1995-07-01

    Information in this report on the staff exchange of Pacific Northwest Laboratory (PNL) staff with the AIGER Consortium (General Motors, Ford, Chrysler, Navistar, the environmental protection Agency, and the California Air Resources Board) includes the purpose and objectives, a summary of activities, significant accomplishments, significant problems, industry benefits realized, recommended follow-on work and potential benefits from that work, and two appendices. Appendix A is a brief description of the fast gas chromatography and infrared spectroscopy chemometric technologies and their application to the rapid characterization of automobile exhaust emissions. Appendix B is a list of key contacts and the schedule of activities pertaining to the staff exchange.

  6. Detectability of vehicle exhaust hydrocarbons: the Wisconsin inspection/maintentance (I/M) analyzer and the remote vehicle emissions sensing (RVES) system

    NASA Astrophysics Data System (ADS)

    Cors, Rebecca; Rendahl, Craig S.

    1995-05-01

    The Wisconsin Departments of Transportation and Natural Resources evaluated the hydrocarbon (HC) detection capability of the Remote Vehicle Emissions Sensing (RVES) system, which employs remote sensing technology, and Wisconsin's I/M analyzers, which use BAR90 specifications. Both analyzers employ non-dispersive infrared (NDIR) technology. Other recent research has quantified HC measurement inaccuracies for vehicle emissions analyzers that use NDIR technology or have BAR90 specifications. This research shows that BAR90 analyzers undermeasure some water- soluble HCs and NDIR analyzers undermeasure olefinic and aromatic HCs. This evaluation was based on both field measurements and calculations that simulate these inaccuracies. These calculations give a measurement accuracy value, which estimates the fraction of the total HCs in a vehicle exhaust sample that each analyzer measures. Other calculations quantify the ozone forming potential of this measured fraction by considering the reactivity of measured HCs. Our field measurements and calculations show Wisconsin I/M analyzer HC measurements are on average 7 percent and 1 percent less than RVES, respectively. Calculations estimate that both analyzers measure at most 43 to 71 percent (an average 61 percent) of the total HCs in an emissions sample. Additional calculations estimate that the HCs measured by both analyzers have 49 to 71 percent (an average 62 percent) of the ozone forming potential of the total HCs in an emissions sample.

  7. Evaluation of Boattail Geometry and Exhaust Plume Temperature Effects on Nozzle Afterbody Drag at Transonic Mach Numbers

    DTIC Science & Technology

    1976-10-01

    AEDC-TR-76-102 t / ,J • • EVALUATION OF BOATTAIL GEOMETRY AND EXHAUST PLUME ~’J_"~!":f~y"~ TEMPERATURE EFFECTS ON NOZZLE AFTERBODY DRAG AT...BOATTAIL GEOMETRY AND EXHAUST PLUME TEMPERATURE EFFECTS ON NOZZLE AFTERBODY DRAG AT TRANSONIC MACH NUMBERS 7 AUTHOR(s ) L. L. G a l i g h e r...combustion) jet test techniques were used to simulate and duplicate, respectively, the nozzle exhaust flow for a sonic jet installatlon. Nozzle exhaust

  8. A quantitative estimation of the exhaust, abrasion and resuspension components of particulate traffic emissions using electron microscopy

    NASA Astrophysics Data System (ADS)

    Weinbruch, Stephan; Worringen, Annette; Ebert, Martin; Scheuvens, Dirk; Kandler, Konrad; Pfeffer, Ulrich; Bruckmann, Peter

    2014-12-01

    relative shares were obtained for PM10: 22% exhaust, 22% abrasion and 56% resuspension (40%, 27%, 33% for PM1). Compared to previous publications we have observed a significantly lower portion of exhaust particles and a significantly higher portion of resuspension particles. The high abundance of resuspension particles underlines their significance for the observed adverse health effects of traffic emissions and for mitigation measures.

  9. Primary emissions and secondary organic aerosol formation from the exhaust of a flex-fuel (ethanol) vehicle

    NASA Astrophysics Data System (ADS)

    Suarez-Bertoa, R.; Zardini, A. A.; Platt, S. M.; Hellebust, S.; Pieber, S. M.; El Haddad, I.; Temime-Roussel, B.; Baltensperger, U.; Marchand, N.; Prévôt, A. S. H.; Astorga, C.

    2015-09-01

    Incentives to use biofuels may result in increasing vehicular emissions of compounds detrimental to air quality. Therefore, regulated and unregulated emissions from a Euro 5a flex-fuel vehicle, tested using E85 and E75 blends (gasoline containing 85% and 75% of ethanol (vol/vol), respectively), were investigated at 22 and -7 °C over the New European Driving Cycle, at the Vehicle Emission Laboratory at the European Commission Joint Research Centre Ispra, Italy. Vehicle exhaust was comprehensively analyzed at the tailpipe and in a dilution tunnel. A fraction of the exhaust was injected into a mobile smog chamber to study the photochemical aging of the mixture. We found that emissions from a flex-fuel vehicle, fueled by E85 and E75, led to secondary organic aerosol (SOA) formation, despite the low aromatic content of these fuel blends. Emissions of regulated and unregulated compounds, as well as emissions of black carbon (BC) and primary organic aerosol (POA) and SOA formation were higher at -7 °C. The flex-fuel unregulated emissions, mainly composed of ethanol and acetaldehyde, resulted in very high ozone formation potential and SOA, especially at low temperature (860 mg O3 km-1 and up to 38 mg C kg-1). After an OH exposure of 10 × 106 cm-3 h, SOA mass was, on average, 3 times larger than total primary particle mass emissions (BC + POA) with a high O:C ratio (up to 0.7 and 0.5 at 22 and -7 °C, respectively) typical of highly oxidized mixtures. Furthermore, high resolution organic mass spectra showed high 44/43 ratios (ratio of the ions m/z 44 and m/z 43) characteristic of low-volatility oxygenated organic aerosol. We also hypothesize that SOA formation from vehicular emissions could be due to oxidation products of ethanol and acetaldehyde, both short-chain oxygenated VOCs, e.g. methylglyoxal and acetic acid, and not only from aromatic compounds.

  10. 40 CFR 1051.103 - What are the exhaust emission standards for snowmobiles?

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ...) Natural gas-fueled snowmobiles: NMHC emissions. (2) Alcohol-fueled snowmobiles: THCE emissions. (3) Other... marketing materials for any vehicles in the engine family. (ii) Your basic mechanical warranty for...

  11. Time-resolved nature of exhaust gas emissions and piston wall temperature under transient operation in a small diesel engine

    SciTech Connect

    Reksowardojo, I.K.; Ogawa, Hideyuki; Miyamoto, Noboru; Enomoto, Yoshiteru; Kitamura, Toru

    1996-09-01

    Diesel combustion and exhaust gas emissions under transient operation (when fuel amounts abruptly increased) were investigated under a wide range of operating conditions with a newly developed gas sampling system. The relation between gas emissions and piston wall temperatures was also investigated. The results indicated that after the start of acceleration NOx, THC and smoke showed transient behaviors before reaching the steady state condition. Of the three gases, THC was most affected by piston wall temperature; its concentration decreased as the wall temperature increased throughout the acceleration except immediately after the start of acceleration. The number of cycles, at which gas concentrations reach the steady-state value after the start of acceleration, were about 1.2 times the cycle constant of the piston wall temperature for THC, and 2.3 times for smoke.

  12. Effects of Fresh and Aged Vehicular Exhaust Emissions on Breathing Pattern and Cellular Responses – Pilot Single Vehicle Study

    PubMed Central

    Diaz, Edgar A.; Chung, Yeonseung; Papapostolou, Vasileios; Lawrence, Joy; Long, Mark S.; Hatakeyama, Vivian; Gomes, Brenno; Calil, Yasser; Sato, Rodrigo; Koutrakis, Petros; Godleski, John J.

    2013-01-01

    The study presented here is a laboratory pilot study using diluted car exhaust from a single vehicle to assess differences in toxicological response between primary emissions and secondary products resulting from atmospheric photochemical reactions of gas phase compounds with O3, OH and other radicals. Sprague-Dawley rats were exposed for five hours to either filtered room air (Sham) or one of two different atmospheres: 1. Diluted Car Exhaust (P) + Mt. Saint Helens Ash (MSHA); 2. P+MSHA+SOA (Secondary Organic Aerosol, formed during simulated photochemical aging of diluted exhaust). Primary and secondary gases were removed using a non-selective diffusion denuder. Continuous respiratory data was collected during the exposure, and broncho-alveolar lavage (BAL) and complete blood counts (CBC) were performed 24 hours after exposure. ANOVA models were used to assess the exposure effect and to compare those effects across different exposure types. Total average exposures were 363±66 μg/m3 P+MSHA and 212±95 μg/m3 P+MSHA+SOA. For both exposures, we observed decreases in breathing rate, tidal and minute volumes (TV, MV) and peak and median flows (PIF, PEF and EF50) along with increases in breathing cycle times (Ti, Te) compared to sham. These results indicate that the animals are changing their breathing pattern with these test atmospheres. Exposure to P+MSHA+SOA produced significant increases in Total Cells, Macrophages and Neutrophils in the BAL and in-vivo chemiluminescence of the lung. There were no significant differences in CBC parameters. Our data suggest that simulated atmospheric photochemistry, producing SOA in the P+MSHA+SOA exposures, enhanced the toxicity of vehicular emissions. PMID:22486346

  13. Exposure assessment of PM2.5 and urinary 8-OHdG for diesel exhaust emission inspector.

    PubMed

    Lee, Mei-Wen; Chen, Mei-Lien; Lung, Shih-Chun Candice; Tsai, Chung-Jung; Yin, Xin-Jie; Mao, I-Fang

    2010-01-01

    Animal studies have shown exposure to diesel exhaust particles (DEPs) to induce production of reactive oxygen species (ROSs) and increase levels of 8-hydroxydeoxyquanosine (8-OHdG). Controversial results have been obtained regarding the effects of workplace exposure on urinary 8-OHdG level. This study assessed concentrations of environmental PM(2.5) in DEP (DEP(2.5)), personal DEP(2.5) and urinary 8-OHdG of diesel engine exhaust emission inspector (inspector) at a diesel vehicle emission inspection station (inspection station). The analysis specifically focuses on the factors that influence inspector urinary 8-OHdG. Repeated-measures study design was used to sample for five consecutive days. A total of 25 environmental PM(2.5) measurements were analyzed at 5 different locations by using a dichotomous sampler, and a total of 55 personal PM(2.5) measurements were analyzed from inspectors by using PM(2.5) personal sampler. During the sampling period, a total of 110 pre- and post-work urine samples from inspectors, and 32 samples from the control group were collected. Following age and sex matching between the inspectors and the control group, levels of urinary 8-OHdG were analyzed. Environmental and personal concentrations of DEP(2.5) were 107.25+/-39.76 (mean+/-SD) and 155.96+/-75.70 microg/m(3), respectively. Also, the concentration of urinary 8-OHdG differed significantly between inspector and control non-smokers, averaging 14.05+/-12.71 and 6.58+/-4.39 microg/g creatinine, respectively. Additionally, urinary 8-OHdG concentrations were associated with diesel exposure after controlling for smoking and cooking at home. Compared with the control group, the inspector displayed significantly increased levels of urinary 8-OHdG. Diesel exhaust is the single pollutant involved in the exposure of DEP(2.5) at the inspection station, as confirmed by the final results.

  14. RSM Based Optimization of Chemical and Enzymatic Transesterification of Palm Oil: Biodiesel Production and Assessment of Exhaust Emission Levels

    PubMed Central

    Mumtaz, Muhammad Waseem; Anwar, Farooq; Saari, Nazamid

    2014-01-01

    Current study presents RSM based optimized production of biodiesel from palm oil using chemical and enzymatic transesterification. The emission behavior of biodiesel and its blends, namely, POB-5, POB-20, POB-40, POB-50, POB-80, and POB-100 was examined using diesel engine (equipped with tube well). Optimized palm oil fatty acid methyl esters (POFAMEs) yields were depicted to be 47.6 ± 1.5, 92.7 ± 2.5, and 95.4 ± 2.0% for chemical transesterification catalyzed by NaOH, KOH, and NaOCH3, respectively, whereas for enzymatic transesterification reactions catalyzed by NOVOZYME-435 and A. n. lipase optimized biodiesel yields were 94.2 ± 3.1 and 62.8 ± 2.4%, respectively. Distinct decrease in particulate matter (PM) and carbon monoxide (CO) levels was experienced in exhaust emissions from engine operating on biodiesel blends POB-5, POB-20, POB-40, POB-50, POB-80, and POB-100 comparative to conventional petroleum diesel. Percentage change in CO and PM emissions for different biodiesel blends ranged from −2.1 to −68.7% and −6.2 to −58.4%, respectively, relative to conventional diesel, whereas an irregular trend was observed for NOx emissions. Only POB-5 and POB-20 showed notable reductions, whereas all other blends (POB-40 to POB-100) showed slight increase in NOx emission levels from 2.6 to 5.5% comparative to petroleum diesel. PMID:25162053

  15. Exhaust emissions survey of a turbofan engine for flame holder swirl type augmentors at simulated altitude flight conditions

    NASA Technical Reports Server (NTRS)

    Moss, J. E., Jr.

    1981-01-01

    Emissions of carbon dioxide, total oxides of nitrogen, unburned hydrocarbons, and carbon monoxide from an F100 afterburning two spool turbofan engine at simulated flight conditions are reported. Tests were run at Mach 0.8 at altitudes of 10.97 and 13.71 km (36,000 and 45,000 ft), and at Mach 1.2 at 13.71 km (45,000 ft). Emission measurements were made from intermediate power (nonafterburning) through maximum afterburning, using a single point gas sample probe traversed across the horizontal diameter of the exhaust nozzle. The data show that emissions vary with flight speed, altitude, power level, and radial position across the nozzle. Carbon monoxide emissions were low for intermediate and partial afterburning power. Unburned hydrocarbons were near zero for most of the simulated flight conditions. At maximum afterburning, there were regions of NOx deficiency in regions of high CO. The results suggest that the low NOx levels observed in the tests are a result of interaction with high CO in the thermal converter. CO2 emissions were proportional to local fuel air ratio for all test conditions.

  16. Effects of fuel ethanol content and volatility on regulated and unregulated exhaust emissions for the latest technology gasoline vehicles.

    PubMed

    Durbin, Thomas D; Miller, J Wayne; Younglove, Theodore; Huai, Tao; Cockert, Kathalena

    2007-06-01

    Oxygenate content and fuel volatility (distillation) variables are important parameters affecting vehicle exhaust emissions, and data on their effects on the latest technology vehicles are quite limited. For this study, 12 California-certified LEV to SULEV vehicles were tested on a matrix of 12 fuels with varying levels of ethanol concentration (0, 5.7, and 10 vol %), T50 (195, 215, and 235 degrees F), and T90 (295, 330, and 355 degrees F). There were statistically significant interactions between ethanol and T90 for NMHC, ethanol, and T50 for CO and ethanol and T50 for NO(x). NMHC emissions increased with increasing ethanol content at the midpoint and high level of T90 but were unaffected at the low T90 level. CO emissions decreased as the ethanol content increased from the low to the midpoint level for all levels of T50, but between the 5.7 and 10% ethanol levels, CO showed only an increase for the high level of T50. NO(x) emissions increased with ethanol content for some conditions. Non-methane organic gases (NMOG) and toxic emissions were examined for only a subset of fuels with the highest T90 level, with NMOG, acetaldehyde, benzene, and 1-,3-butadiene all found to increase with increasing ethanol content.

  17. GC/MS and MS/MS studies of diesel exhaust mutagenicity and emissions from chemically defined fuels

    SciTech Connect

    Henderson, T.R.; Sun, J.D.; Li, A.P.; Hanson, R.L.; Bechtold, W.E.; Harvey, T.M.; Shabanowitz, J.; Hunt, D.F.

    1984-06-01

    Selected polycyclic aromatic hydrocarbons (PAHs) dissolved in an aliphatic solvent (hexadecane) were utilized as fuels in a single cylinder diesel engine to examine relationships between diesel fuel aromaticity, PAH content, and the mutagenic activities associated with diesel soot. The direct-acting mutagenic response to Salmonella and the percent extractable organics associated with soot particles was 3-4-fold lower when pure hexadecane was combusted compared to reference diesel fuel. Certain PAHs (pyrene and phenanthrene) when added to aliphatic fuel caused increased emissions of the same PAH and increased nitro-PAH emissions corresponding to the parent PAHs but no increase in soot production. Other PAHs (1-methylnaphthalene, acenaphthene, and benzo(a)pyrene) increased the overall emissions of several PAHs and soot and altered patterns of nitro-PAH emissions. It was concluded that the incomplete combustion of PAHs through soot-forming mechanisms may significantly influence exhaust emissions of PAHs and nitro-PAHs from diesel engines, and the concentration on soot particles reflects both the boiling point and the relative stability of individual compounds.

  18. RSM based optimization of chemical and enzymatic transesterification of palm oil: biodiesel production and assessment of exhaust emission levels.

    PubMed

    Mumtaz, Muhammad Waseem; Mukhtar, Hamid; Anwar, Farooq; Saari, Nazamid

    2014-01-01

    Current study presents RSM based optimized production of biodiesel from palm oil using chemical and enzymatic transesterification. The emission behavior of biodiesel and its blends, namely, POB-5, POB-20, POB-40, POB-50, POB-80, and POB-100 was examined using diesel engine (equipped with tube well). Optimized palm oil fatty acid methyl esters (POFAMEs) yields were depicted to be 47.6 ± 1.5, 92.7 ± 2.5, and 95.4 ± 2.0% for chemical transesterification catalyzed by NaOH, KOH, and NaOCH3, respectively, whereas for enzymatic transesterification reactions catalyzed by NOVOZYME-435 and A. n. lipase optimized biodiesel yields were 94.2 ± 3.1 and 62.8 ± 2.4%, respectively. Distinct decrease in particulate matter (PM) and carbon monoxide (CO) levels was experienced in exhaust emissions from engine operating on biodiesel blends POB-5, POB-20, POB-40, POB-50, POB-80, and POB-100 comparative to conventional petroleum diesel. Percentage change in CO and PM emissions for different biodiesel blends ranged from -2.1 to -68.7% and -6.2 to -58.4%, respectively, relative to conventional diesel, whereas an irregular trend was observed for NOx emissions. Only POB-5 and POB-20 showed notable reductions, whereas all other blends (POB-40 to POB-100) showed slight increase in NOx emission levels from 2.6 to 5.5% comparative to petroleum diesel.

  19. Chemical characterization of exhaust emissions from selected canadian marine vessels: the case of trace metals and lanthanoids.

    PubMed

    Celo, Valbona; Dabek-Zlotorzynska, Ewa; McCurdy, Mark

    2015-04-21

    This paper reports the chemical composition of exhaust emissions from the main engines of five ocean going cargo vessels, as they traveled in Canadian waters. The emission factors (EFs) of PM2.5 and SO2 for vessels tested on various intermediate fuel oils (IFO), ranged from 0.4 to 2.2 g kW(-1) hr(-1) and 4.7 to 10.3 g kW(-1) hr(-1), respectively, and were mainly dependent on the content of sulfur in the fuel. Average NOx, CO, and CO2 EFs for these tests were 12.7, 0.45, and 618 g kW(-1) hr(-1), respectively and were generally below benchmark values commonly used by regulatory agencies. The composition of PM2.5 was dominated by hydrated sulfates, organic carbon and trace metals which accounted for 80-97% of total PM2.5 mass. A substantial decrease of measured emission factors for PM2.5 and SO2 was observed when the fuel was changed from IFO to marine diesel oil (MDO), in one of the tested vessels. The main component of PM2.5 in this case was organic carbon accounting for 65% of PM2.5 mass. In addition to commonly reported pollutants, this study presents EFs of the lanthanoid elements and showed that their distribution patterns in ship-exhaust PM2.5 were very similar to the PM2.5 emitted by oil refining facilities. Hence, using La:Ce:V tertiary diagrams and La/V ratios is necessary to distinguish ship plumes from primary emissions related to accidental and/or routine operation of oil-refining industry.

  20. Particulate matter, carbon emissions and elemental compositions from a diesel engine exhaust fuelled with diesel-biodiesel blends

    NASA Astrophysics Data System (ADS)

    Ashraful, A. M.; Masjuki, H. H.; Kalam, M. A.

    2015-11-01

    A comparative morphological analysis was performed on the exhaust particles emitted from a CI engine using different blending ratios of palm biodiesel at several operating conditions. It was observed from this experiment; peak particle concentration for PB10 at 1200 rpm is 1.85E + 02 and at 1500 rpm is 2.12E + 02. A slightly smaller amount of volatile material has found from the biodiesel samples compared to the diesel fuel sample. Thermogravimetric analysis (TGA) showed that the amount of volatile material in the soot from biodiesel fuels was slightly lower than that of diesel fuel. PB20 biodiesel blends reduced maximum 11.26% of volatile matter from the engine exhaust, while PB10 biodiesel blend reduced minimum 5.53% of volatile matter. On the other hand, the amount of fixed carbon from the biodiesel samples was slightly higher than diesel fuel. Analysis of carbon emissions, palm biodiesel (PB10) reduced elemental carbon (EC) was varies 0.75%-18%, respectively. Similarly, the emission reduction rate for PB20 was varies 11.36%-23.46% respectively. While, organic carbon (OC) emission rates reduced for PB20 was varied 13.7-49% respectively. Among the biodiesel blends, PB20 exhibited highest oxygen (O), sulfur (S) concentration and lowest silicon (Si) and iron (Fe) concentration. Scanning electron microscope (SEM) images for PB20 showed granular structure particulates with bigger grain sizes compared to diesel. Particle diameter increased under the 2100-2400 rpm speed condition and it was 8.70% higher compared to the low speed conditions. Finally, the results indicated that the composition and degree of unsaturation of the methyl ester present in biodiesel, play an important role in the chemical composition of particulate matter emissions.

  1. The Use of Exhaust Gas Recirculation to Optimize Fuel Economy and Minimize Emission in Engines Operating on E85 Fuel

    SciTech Connect

    Wu, Ko-Jen

    2011-12-31

    This report summarizes activities conducted for the project “The Use of Exhaust Gas Recirculation to Optimized Fuel Economy and Minimize Emissions in Engines Operating on E85 Fuel” under COOPERATIVE AGREEMENT NUMBER DE-FC26-07NT43271, which are as outlined in the STATEMENT OF PROJECT OBJECTIVES (SOPO) dated March 2007 and in the supplemental SOPO dated October 2010. The project objective was to develop and demonstrate an internal combustion engine that is optimized for E85 (85% ethanol and 15% gasoline) fuel operation to achieve substantially improved fuel economy while operating with E85 fuel and that is also production viable in the near- to medium-term. The key engine technology selected for research and development was turbocharging, which is known to improve fuel economy thru downsizing and is in particular capable of exploiting ethanol fuel’s characteristics of high octane number and high latent heat of vaporization. The engine further integrated synergistic efficiency improving technologies of cooled exhaust gas recirculation (EGR), direct fuel injection and dual continuously variable intake and exhaust cam phasers. On the vehicle level, fuel economy was furthered thru powertrain system optimization by mating a state-of-the-art six-speed automatic transmission to the engine. In order to achieve the project’s objective of near- to medium-term production viability, it was essential to develop the engine to be flex-fuel capable of operating with fuels ranging from E0 (0% ethanol and 100% gasoline) to E85 and to use three-way type of catalyst technology for exhaust aftertreatment. Within these scopes, various technologies were developed through systems approach to focus on ways to help accelerate catalyst light-off. Significant amount of development took place during the course of the project within General Motors, LLC. Many prototype flex-fuel engines were designed, built and developed with various hardware configurations selected to achieve the project

  2. Detailed characterization and profiles of crankcase and diesel particulate matter exhaust emissions using speciated organics.

    PubMed

    Zielinska, Barbara; Campbell, David; Lawson, Douglas R; Ireson, Robert G; Weaver, Christopher S; Hesterberg, Thomas W; Larson, Timothy; Davey, Mark; Liu, L J Sally

    2008-08-01

    A monitoring campaign was conducted in August-September 2005 to compare different experimental approaches quantifying school bus self-pollution. As part of this monitoring campaign, a detailed characterization of PM2.5 diesel engine emissions from the tailpipe and crankcase emissions from the road draft tubes was performed. To distinguish between tailpipe and crankcase vent emissions, a deuterated alkane, n-hexatriacontane-d74 (n-C36D74) was added to the engine oil to serve as an intentional quantitative tracer for lubricating oil PM emissions. This paper focuses on the detailed chemical speciation of crankcase and tailpipe PM emissions from two school buses used in this study. We found that organic carbon emission rates were generally higher from the crankcase than from the tailpipe for these two school buses, while elemental carbon contributed significantly only in the tailpipe emissions. The n-C36D74 that was added to the engine oil was emitted at higher rates from the crankcase than the tailpipe. Tracers of engine oil (hopanes and steranes) were present in much higher proportion in crankcase emissions. Particle-associated PAH emission rates were generally very low (< 1 microg/km), but more PAH species were present in crankcase than in tailpipe emissions. The speciation of samples collected in the bus cabins was consistent with most of the bus self-pollution originating from crankcase emissions.

  3. Detailed Characterization and Profiles of Crankcase and Diesel Particular Matter Exhaust Emissions Using Speciated Organics

    PubMed Central

    Zielinska, Barbara; Campbell, David; Lawson, Douglas R.; Ireson, Robert G.; Weaver, Christopher S.; Hesterberg, Thomas W.; Larson, Timothy; Davey, Mark; Liu, L.-J. Sally

    2008-01-01

    A monitoring campaign was conducted in August-September 2005 to compare different experimental approaches quantifying school bus self-pollution. As part of this monitoring campaign, a detailed characterization of PM2.5 diesel engine emissions from the tailpipe and crankcase emissions from the road draft tubes was performed. To distinguish between tailpipe and crankcase vent emissions, a deuterated alkane, n-hexatriacontane-d74 (n-C36D74) was added to the engine oil to serve as intentional quantitative tracers for lubricating oil PM emissions. This paper focuses on the detailed chemical speciation of crankcase and tailpipe PM emissions from two school buses used in this study. We found that organic carbon emission rates were generally higher from the crankcase than from the tailpipe for these two school buses, while elemental carbon contributed significantly only in the tailpipe emissions. The n-C36D74 that was added to the engine oil was emitted at higher rates from the crankcase than the tailpipe. Tracers of engine oil (hopanes, and steranes) were present in much higher proportion in crankcase emissions. Particle-associated PAH emission rates were generally very low (< 1 μg/km), but more PAH species were present in crankcase than in tailpipe emissions. The speciation of samples collected in the bus cabins was consistent with most of the bus self-pollution originating from crankcase emissions. PMID:18754490

  4. Detailed Characterization and Profiles of Crankcase and Diesel Particulate Matter Exhaust Emissions Using Speciated Organics

    SciTech Connect

    Zielinska, B.; Campbell, D.; Lawson, D. R.; Ireson, R. G.; Weaver, C. S.; Hesterberg, T. W.; Larson, T.; Davey, M.; Sally Liu, L.-J.

    2008-01-01

    A monitoring campaign was conducted in August-September 2005 to compare different experimental approaches quantifying school bus self-pollution. As part of this monitoring campaign, a detailed characterization of PM2.5 diesel engine emissions from the tailpipe and crankcase emissions from the road draft tubes was performed. To distinguish between tailpipe and crankcase vent emissions, a deuterated alkane, n-hexatriacontane-d74 (n-C36D74) was added to the engine oil to serve as an intentional quantitative tracer for lubricating oil PM emissions. This paper focuses on the detailed chemical speciation of crankcase and tailpipe PM emissions from two school buses used in this study. We found that organic carbon emission rates were generally higher from the crankcase than from the tailpipe for these two school buses, while elemental carbon contributed significantly only in the tailpipe emissions. The n-C36D74 that was added to the engine oil was emitted at higher rates from the crankcase than the tailpipe. Tracers of engine oil (hopanes and steranes) were present in much higher proportion in crankcase emissions. Particle-associated PAH emission rates were generally very low (<1 {micro}g/km), but more PAH species were present in crankcase than in tailpipe emissions. The speciation of samples collected in the bus cabins was consistent with most of the bus self-pollution originating from crankcase emissions.

  5. Estimation of exhaust emission from ocean-going vessels in Hong Kong.

    PubMed

    Yau, P S; Lee, S C; Corbett, James J; Wang, Chengfeng; Cheng, Y; Ho, K F

    2012-08-01

    As one of the busiest port in the world, ship emissions have become of great concern in Hong Kong. In this study, a detailed maritime emission inventory for ocean-going vessels (OGVs) in Hong Kong with the base year of 2007 was developed. The high-resolution vessel speed profiles determined using the Automatic Identification System (AIS) during 2009 were adopted for the speed data in the estimation. It was obtained that the total ship emissions from 37,150 voyages of OGVs in 2007 were 17,097, 8190, and 1035 tonnes accounting for 17%, 11%, and 16% of the total emissions of NO(x), SO(2), and PM(10), respectively. The contribution of ship emissions during transiting was 60-68% for three pollutants while the emissions during hotelling were responsible for the remaining portions. From the emission spatial allocation, the shipping route along the East Lamma Channel and the berthing location of the Kwai Chung and Tsing Yi Container Port comprised the regions with the highest emissions. The OGV emissions in Hong Kong contributed 0.07% NO(x), 0.05% SO(2), and 0.06% PM(10) out of the global total shipping emissions in 2007.

  6. Secondary Organic Aerosol Formation from Ultra-Low Super Ultra-Low and Partial Zero Emission Vehicle Exhaust

    NASA Astrophysics Data System (ADS)

    Robinson, A. L.; Zhao, Y.; Lambe, A. T.; Saleh, R.; Saliba, G.; Maldonado, H.; Sardar, S.; Frodin, B.; Drozd, G.; Goldstein, A. H.; Kroll, J. H.; Cross, E. S.; Franklin, J. P.

    2015-12-01

    Secondary organic aerosol (SOA) is the dominant component of organic aerosol in many urban areas during the summertime. On-road light duty gasoline vehicles (LDGV) have been indicated as a major source of SOA precursors. Emissions of the SOA-forming non methane hydrocarbons (NMHCs) from on-road LDGV have been substantially reduced along with more stringent emission standards, leading to reduced potential for SOA formation. However, recent smog chamber measurements reported that the reductions in SOA formation were less than those in NMHC emissions, indicating that newer, low emitting vehicles may emit a more efficient of SOA precursors. Vehicles that meet the ultra-low, super ultra-low and partial zero emission standards have substantially lower NMHC emissions than vehicles tested in past studies. To better understand the effects of more stringent emission controls on the SOA formation, we conducted experiments 13 vehicles recruited from the Southern California vehicle fleet (five ultra-low emission vehicles, four super ultra-low emission vehicles and four partial zero emission vehicles) at the California Air Resources Board Haagen-Smit Laboratory. In addition, we investigated several vehicles compliant with older emission standards have also been investigated here to bridge the previous studies. Dilute vehicle exhaust were photo-oxidized in a smog chamber with the VOC-to-NOx ratio adjusted to simulate the photochemistry in urban air. Application of literature data from single-ring aromatic compounds cannot explain the observed SOA during chamber experiments. The average ratios between estimated and measured SOA for vehicles under different emission standards ranged from 0.04 to 0.71. Comprehensive measurements of SOA precursor emissions were made, including NMHCs, intermediate volatility and semi-volatile organic compounds. This study presents results of SOA production from these low emitting vehicles and compares the results with recently published data. This

  7. Exhaust emission survey of an F100 afterburning turbofan engine at simulated altitude flight conditions

    NASA Technical Reports Server (NTRS)

    Moss, J. E.; Cullom, R. R.

    1981-01-01

    Emissions of carbon monoxide, total oxides of nitrogen, unburned hydrocarbons, and carbon dioxide from an F100, afterburning, two spool turbofan engine at simulated flight conditions are reported. For each flight condition emission measurements were made for two or three power levels from intermediate power (nonafterburning) through maximum afterburning. The data showed that emissions vary with flight speed, altitude, power level, and radial position across the nozzle. Carbon monoxide emissions were low for intermediate power (nonafterburning) and partial afterburning, but regions of high carbon monoxide were present downstream of the flame holder at maximum afterburning. Unburned hydrocarbon emissions were low for most of the simulated flight conditions. The local NOX concentrations and their variability with power level increased with increasing flight Mach number at constant altitude, and decreased with increasing altitude at constant Mach number. Carbon dioxide emissions were proportional to local fuel air ratio for all conditions.

  8. Jet aircraft engine exhaust emissions database development: Year 1990 and 2015 scenarios

    NASA Technical Reports Server (NTRS)

    Landau, Z. Harry; Metwally, Munir; Vanalstyne, Richard; Ward, Clay A.

    1994-01-01

    Studies relating to environmental emissions associated with the High Speed Civil Transport (HSCT) military jet and charter jet aircraft were conducted by McDonnell Douglas Aerospace Transport Aircraft. The report includes engine emission results for baseline 1990 charter and military scenario and the projected jet engine emissions results for a 2015 scenario for a Mach 1.6 HSCT charter and military fleet. Discussions of the methodology used in formulating these databases are provided.

  9. MOBILE4 exhaust emission factors and inspection/maintenance benefits for passenger cars. Technical report

    SciTech Connect

    Glover, E.L.; Brzezinski, D.J.

    1989-08-01

    The MOBILE4 Tech IV Credit Model is used to estimate the emission factor equations, the effects of Inspection and Maintenance (I/M) programs, and the bag fraction equations for 1981 and later passenger cars. The model's results are then stored in the EPA MOBILE4 emission factor model data base. The report describes the development, use, and results of the Tech IV model. It also documents the normalized bag fractions, high-altitude emission factors, biennial I/M credits, and idle-emission I/M credits used in MOBILE4.

  10. Emission of polycyclic aromatic hydrocarbons from light-duty diesel vehicles exhaust

    NASA Astrophysics Data System (ADS)

    de Abrantes, Rui; de Assunção, João V.; Pesquero, Célia R.

    Standardised tests were performed on four light-duty diesel vehicles running in a chassis dynamometer at a vehicular emission laboratory, using the FTP-75 test cycle procedure. The aim was to characterise emissions of Polycyclic Aromatic Hydrocarbons (PAHs), substances that create health hazards and are, as yet, unregulated. The pollutants were analysed in both solid and gaseous phases using high-performance liquid chromatography. Total PAH values ranged from 1.133 to 5.801 mg km -1. Naphthalene, phenanthrene, fluoranthene, pyrene and chrysene were detected in all tests. In addition, PAH emission was observed to be inversely related to emission of CO 2.

  11. A Gas Chromatograph/Mass Spectrometer System for UltraLow-Emission Combustor Exhaust Studies

    NASA Technical Reports Server (NTRS)

    Brabbs, Theodore A.; Wey, Chowen Chou

    1996-01-01

    A gas chromatograph (GC)/mass spectrometer (MS) system that allows the speciation of unburnt hydrocarbons in the combustor exhaust has been developed at the NASA Lewis Research Center. Combustion gas samples are withdrawn through a water-cooled sampling probe which, when not in use, is protected from contamination by a high-pressure nitrogen purge. The sample line and its connecting lines, filters, and valves are all ultraclean and are heated to avoid condensation. The system has resolution to the parts-per-billion (ppb) level.

  12. Preface: Special Issue on Catalytic Control of Lean-Burn Engine Exhaust Emissions

    SciTech Connect

    Yezerets, Aleksey; Peden, Charles HF; Szanyi, Janos; Nova, Isabella; Epling, Bill

    2012-04-30

    This issue of Catalysis Today includes original research articles based on select presentations from the Mobile Emissions Control Symposium at the 22nd North American Catalysis Society (NACS) Meeting held in Detroit in June 2011, with a particular focus on catalyzed diesel emissions control. The Symposium was dedicated to the memory of Dr. Haren Gandhi, a visionary technology leader and a passionate environmental advocate.

  13. 40 CFR 87.23 - Exhaust emission standards for Tier 6 and Tier 8 engines.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... engines determined to be derivative engines for emissions certification purposes under the requirements of... determined to be derivative engines for emissions certification purposes under the requirements of this part... engines installed (or delivered for installation) on military aircraft. (2) Engine type...

  14. METHANE EMISSIONS FROM THE NATURAL GAS INDUSTRY VOLUME 11: COMPRESSOR DRIVER EXHAUST

    EPA Science Inventory

    The 15-volume report summarizes the results of a comprehensive program to quantify methane (CH4) emissions from the U.S. natural gas industry for the base year. The objective was to determine CH4 emissions from the wellhead and ending downstream at the customer's meter. The accur...

  15. 40 CFR 87.64 - Sampling and analytical procedures for measuring gaseous exhaust emissions.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 1, 2011, report CO2 values along with your emission levels of regulated NOX to the Administrator for... on or after January 1, 2011. By January 1, 2011, report CO2 values along with your emission levels of... date of manufacture of the individual engine was before January 1, 2011. Round CO2 to the nearest 1 g...

  16. 40 CFR 87.64 - Sampling and analytical procedures for measuring gaseous exhaust emissions.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ...) (b) Starting January 1, 2011, report CO2 values along with your emission levels of regulated NOX to... individual production model was on or after January 1, 2011. By January 1, 2011, report CO2 values along with your emission levels of regulated NOX to the Administrator for engines currently in production and of a...

  17. 40 CFR 87.21 - Exhaust emission standards for Tier 4 and earlier engines.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ...: 118 grams/kilonewton rO. (iii) The following Tier 0 emission standard applies for engines of a type or... standard applies for engines of a type or model of which the date of manufacture of the first individual... 7, 1997. (vi) The following Tier 4 emission standards apply for engines of a type or model of which...

  18. 40 CFR 87.21 - Exhaust emission standards for Tier 4 and earlier engines.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ...: 118 grams/kilonewton rO. (iii) The following Tier 0 emission standard applies for engines of a type or... standard applies for engines of a type or model of which the date of manufacture of the first individual... 7, 1997. (vi) The following Tier 4 emission standards apply for engines of a type or model of which...

  19. 40 CFR 1042.240 - Demonstrating compliance with exhaust emission standards.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    .... Use a multiplicative deterioration factor if good engineering judgment calls for the deterioration... emissions at the low-hour test point. For example, if you use aftertreatment technology that controls... atmosphere, you must account for crankcase emission deterioration, using good engineering judgment. You may...

  20. 40 CFR 1042.240 - Demonstrating compliance with exhaust emission standards.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    .... Use a multiplicative deterioration factor if good engineering judgment calls for the deterioration... emissions at the low-hour test point. For example, if you use aftertreatment technology that controls... atmosphere, you must account for crankcase emission deterioration, using good engineering judgment. You may...

  1. The effects of oxygen-enriched intake air on FFV exhaust emissions using M85

    SciTech Connect

    Poola, R.B.; Sekar, R.; Ng, H.K.; Baudino, J.H.; Colucci, C.P.

    1996-05-01

    This paper presents results of emission tests of a flexible fuel vehicle (FFV) powered by an SI engine, fueled by M85 (methanol), and supplied with oxygen-enriched intake air containing 21, 23, and 25 vol% O2. Engine-out total hydrocarbons (THCs) and unburned methanol were considerably reduced in the entire FTP cycle when the O2 content of the intake air was either 23 or 25%. However, CO emissions did not vary much, and NOx emissions were higher. HCHO emissions were reduced by 53% in bag 1, 84% in bag 2, and 59% in bag 3 of the FTP cycle with 25% oxygen-enriched intake air. During cold-phase FTP,reductions of 42% in THCs, 40% in unburned methanol, 60% in nonmethane hydrocarbons, and 45% in nonmethane organic gases (NMOGs) were observed with 25% enriched air; NO{sub x} emissions increased by 78%. Converter-out emissions were also reduced with enriched air but to a lesser degree. FFVs operating on M85 that use 25% enriched air during only the initial 127 s of cold-phase FTP or that use 23 or 25% enriched air during only cold-phase FTP can meet the reactivity-adjusted NMOG, CO, NO{sub x}, and HCHO emission standards of the transitional low-emission vehicle.

  2. METHANE EMISSIONS FROM THE NATURAL GAS INDUSTRY VOLUME 11: COMPRESSOR DRIVER EXHAUST

    EPA Science Inventory

    The 15-volume report summarizes the results of a comprehensive program to quantify methane (CH4) emissions from the U.S. natural gas industry for the base year. The objective was to determine CH4 emissions from the wellhead and ending downstream at the customer's meter. The accur...

  3. 40 CFR 1066.820 - Composite calculations for FTP exhaust emissions.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... equation: ER28AP14.136 Where: m c = the combined mass emissions determined from the cold-start UDDS test... transient portion of the cold-start test (bag 1), in miles. D cs = the measured driving distance from the stabilized portion of the cold-start test (bag 2), in miles. m h = the combined mass emissions determined...

  4. Characterization of large fleets of vehicle exhaust emissions in middle Taiwan by remote sensing.

    PubMed

    Ko, Ya-Wen; Cho, Chi-Hung

    2006-01-15

    Measurement of fleet emissions by means of remote sensing was conducted in middle Taiwan and the distributions and governing factors were characterized and examined. Results show the type of sampling sites is a dominant factor for the emission levels, and driving speeds and accelerations of the vehicles. In this study, the mean CO, HC, and NO concentrations at the urban and rural sites are apparently higher. The quantitative relationship between the pollutant concentration and mean speed or acceleration was established. Analysis of effect of the vehicle model year on the average fleet emissions was also conducted. It indicates those relatively older vehicles are higher emitters and contribute significantly more to total fleet emissions. On the other hand, the variation trends with model year are independent of the site characteristics and the effect of vehicle age on CO, HC, and NO emission is similar.

  5. The effects of neat biodiesel and biodiesel and HVO blends in diesel fuel on exhaust emissions from a light duty vehicle with a diesel engine.

    PubMed

    Prokopowicz, Adam; Zaciera, Marzena; Sobczak, Andrzej; Bielaczyc, Piotr; Woodburn, Joseph

    2015-06-16

    The influence of fatty acid methyl esters (FAME) and hydrotreated vegetable oil (HVO) diesel blends on the exhaust emissions from a passenger car was examined. The impact of FAME for the cold urban phase (UDC) was increased CO and HC emissions, probably due to blend physical properties promoting incomplete combustion. The HVO blend caused the lowest CO and HC emissions for the UDC. NOx emissions did not change significantly with the fuel used, however the UDC was characterized by lower NOx emission for FAME blends. Particle emissions were highest with standard diesel. Emissions of carbonyl compounds increased as fuel biodiesel content increased, especially during the UDC. HVO in diesel fuel decreased carbonyl emissions. Formaldehyde and acetaldehyde were the most abundant carbonyl compounds in the exhaust gas. Total particle-bound PAH emissions were variable, the emission of heavier PAHs increased with blend biodiesel content. The HVO blend increased emission of lighter PAHs. Nitro-PAHs were identified only during the UDC and not for all blends; the highest emissions were measured for pure diesel. The results showed that emission of nitro-PAHs may be decreased to a greater extent by using biodiesel than using a HVO blend.

  6. Absence of multiplicative interactions between occupational lung carcinogens and tobacco smoking: a systematic review involving asbestos, crystalline silica and diesel engine exhaust emissions.

    PubMed

    El Zoghbi, Mohamad; Salameh, Pascale; Stücker, Isabelle; Brochard, Patrick; Delva, Fleur; Lacourt, Aude

    2017-02-02

    Tobacco smoking is the main cause of lung cancer, but it is not the sole causal factor. Significant proportions of workers are smokers and exposed to occupational lung carcinogens. This study aims to systematically review the statistical interaction between occupational lung carcinogens and tobacco smoking, in particular asbestos, crystalline silica and diesel engine exhaust emissions. Articles were identified using Scopus, PubMed, and Web of Science, and were limited to those published in English or French, without limitation of time. The reference list of selected studies was reviewed to identify other relevant papers. One reviewer selected the articles based on the inclusion and exclusion criteria. Two reviewers checked the eligibility of articles to be included in the systematic review. Data were extracted by one reviewer and revised by two other reviewers. Cohorts and case-control studies were analyzed separately. The risk of bias was evaluated for each study based on the outcome. The results of the interaction between the tobacco smoking and each carcinogen was evaluated and reported separately. Fifteen original studies were included for asbestos-smoking interaction, seven for silica-smoking interaction and two for diesel-smoking interaction. The results suggested the absence of multiplicative interaction between the three occupational lung carcinogens and smoking. There is no enough evidence from the literature to conclude for the additive interaction. We believe there is a limited risk of publication bias as several studies reporting negative results were published. There are no multiplicative interactions between tobacco smoking and occupational lung carcinogens, in particular asbestos, crystalline silica and diesel engine exhaust emissions. Even though, specific programs should be developed and promoted to reduce concomitantly the exposure to occupational lung carcinogens and tobacco smoking.

  7. Final summary report on project 3310 marine diesel exhaust emissions (alternative fuels). Final report

    SciTech Connect

    Bentz, A.P.

    1997-09-01

    This report summarizes the results of a 5-year study to ascertain the magnitude of emission problems from Coast Guard and commercial vessels; to develop methodology applicable for use on small vessels by using portable emission analyzers, and to examine various potential means of reducing excessive emissions. During this project, the Coast Guard RD Center tested eight vessels (of six types); and the Volpe National Transportation Systems Center tested six Coast Guard vessels (of five types) operating on the West Coast. Of the 14 vessels tested, eight were found to exceed the proposed NOx limits, although some by very small amounts.

  8. A portable fiber-optic chemical device for the quantitative determination of carbon monoxide from automobile exhaust emissions.

    PubMed

    Matias, F A; Tubino, M

    2001-07-01

    A colorimetric method for the quantitative determination of CO by diffuse reflectance is described. This method is based on the reduction by CO of Mo (VI) from the indicator reagent molybdosilicic acid (H8Si[Mo2O7]6). The reduction yielded a change of color from clear yellow to dark green on white disk filter chart paper wetted with reagent indicator solution. The gaseous mixture containing CO was forced to pass through this chart paper, initiating the reaction. The intensity of the color produced, measured by diffuse reflectance, was proportional to the CO concentration present in exhaust gases in the range from 0.02 to 12% volume/volume (v/v). A 650-nm light-emitting diode was used as a light source. A two-fiber-optic system carried the light from the source to the detection system, which was composed of a photodiode, an amplification circuit, and a digital display. The method was applied with success in field measurements for automobiles in the Otto cycle. In a previous paper, this method was used for the quantitative determination of exhaust emissions from diesel-fueled vehicles.

  9. 40 CFR 1054.705 - How do I generate and calculate exhaust emission credits?

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... AGENCY (CONTINUED) AIR POLLUTION CONTROLS CONTROL OF EMISSIONS FROM NEW, SMALL NONROAD SPARK-IGNITION... special test procedures for a family under 40 CFR 1065.10(c)(2), consistent with good engineering...

  10. 40 CFR 1045.705 - How do I generate and calculate exhaust emission credits?

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... AGENCY (CONTINUED) AIR POLLUTION CONTROLS CONTROL OF EMISSIONS FROM SPARK-IGNITION PROPULSION MARINE... kilowatts (see § 1045.140). UL = The useful life for the given family. LF = load factor. Use 0.207. We...

  11. 40 CFR 1045.705 - How do I generate and calculate exhaust emission credits?

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... AGENCY (CONTINUED) AIR POLLUTION CONTROLS CONTROL OF EMISSIONS FROM SPARK-IGNITION PROPULSION MARINE... kilowatts (see § 1045.140). UL = The useful life for the given family. LF = load factor. Use 0.207. We...

  12. 40 CFR 1045.705 - How do I generate and calculate exhaust emission credits?

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... AGENCY (CONTINUED) AIR POLLUTION CONTROLS CONTROL OF EMISSIONS FROM SPARK-IGNITION PROPULSION MARINE... kilowatts (see § 1045.140). UL = The useful life for the given family. LF = load factor. Use 0.207. We...

  13. 40 CFR 1045.705 - How do I generate and calculate exhaust emission credits?

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... AGENCY (CONTINUED) AIR POLLUTION CONTROLS CONTROL OF EMISSIONS FROM SPARK-IGNITION PROPULSION MARINE... kilowatts (see § 1045.140). UL = The useful life for the given family. LF = load factor. Use 0.207. We...

  14. 40 CFR 1045.705 - How do I generate and calculate exhaust emission credits?

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... AGENCY (CONTINUED) AIR POLLUTION CONTROLS CONTROL OF EMISSIONS FROM SPARK-IGNITION PROPULSION MARINE... kilowatts (see § 1045.140). UL = The useful life for the given family. LF = load factor. Use 0.207. We...

  15. Black carbon emissions in gasoline exhaust and a reduction alternative with a gasoline particulate filter.

    PubMed

    Chan, Tak W; Meloche, Eric; Kubsh, Joseph; Brezny, Rasto

    2014-05-20

    Black carbon (BC) mass and solid particle number emissions were obtained from two pairs of gasoline direct injection (GDI) vehicles and port fuel injection (PFI) vehicles over the U.S. Federal Test Procedure 75 (FTP-75) and US06 Supplemental Federal Test Procedure (US06) drive cycles on gasoline and 10% by volume blended ethanol (E10). BC solid particles were emitted mostly during cold-start from all GDI and PFI vehicles. The reduction in ambient temperature had significant impacts on BC mass and solid particle number emissions, but larger impacts were observed on the PFI vehicles than the GDI vehicles. Over the FTP-75 phase 1 (cold-start) drive cycle, the BC mass emissions from the two GDI vehicles at 0 °F (-18 °C) varied from 57 to 143 mg/mi, which was higher than the emissions at 72 °F (22 °C; 12-29 mg/mi) by a factor of 5. For the two PFI vehicles, the BC mass emissions over the FTP-75 phase 1 drive cycle at 0 °F varied from 111 to 162 mg/mi, higher by a factor of 44-72 when compared to the BC emissions of 2-4 mg/mi at 72 °F. The use of a gasoline particulate filter (GPF) reduced BC emissions from the selected GDI vehicle by 73-88% at various ambient temperatures over the FTP-75 phase 1 drive cycle. The ambient temperature had less of an impact on particle emissions for a warmed-up engine. Over the US06 drive cycle, the GPF reduced BC mass emissions from the GDI vehicle by 59-80% at various temperatures. E10 had limited impact on BC emissions from the selected GDI and PFI vehicles during hot-starts. E10 was found to reduce BC emissions from the GDI vehicle by 15% at standard temperature and by 75% at 19 °F (-7 °C).

  16. Simultaneous removals of NOx, HC and PM from diesel exhaust emissions by dielectric barrier discharges.

    PubMed

    Song, Chong-Lin; Bin, Feng; Tao, Ze-Min; Li, Fang-Cheng; Huang, Qi-Fei

    2009-07-15

    The main target of this work is to characterize the abatements of particulate matter (PM), hydrocarbons (HC) and nitrogen oxides (NO(x)) from an actual diesel exhaust using dielectric barrier discharge technology (DBD). The effects of several parameters, such as peak voltage, frequency and engine load, on the contaminant removals have been investigated intensively. The present study shows that for a given frequency, the removals of PM and HC are enhanced with the increase of peak voltage and level off at higher voltage, while in the range of higher voltages a decline of NO(x) removal efficiency is observed. For a given voltage, the maximums of specific energy density (SED) and removal efficiency are attained at resonance point. The increase of peak voltage will result in a significant decrease of energy utilization efficiency of DBD at most engine loads. Alkanes in soluble organic fraction (SOF) are more readily subjected to removals than polycyclic aromatic hydrocarbons (PAHs).

  17. Detection of emission indices of aircraft exhaust compounds by open-path optical methods at airports

    NASA Astrophysics Data System (ADS)

    Schürmann, Gregor; Schäfer, Klaus; Jahn, Carsten; Hoffmann, Herbert; Utzig, Selina

    2005-10-01

    Air pollutant emission rates of aircrafts are determined with test bed measurements. Regulations exist for CO2, NO, NO2, CO concentrations, the content of total unburned hydrocarbons and the smoke number, a measure of soot. These emission indices are listed for each engine in a data base of the International Civil Aviation Organisation (ICAO) for four different Air pollutant emission rates of aircrafts are determined with test bed measurements. Regulations exist for CO2, NO, NO2, CO concentrations, the content of total unburned hydrocarbons and the smoke number, a measure of soot. These emission indices are listed for each engine in a data base of the International Civil Aviation Organisation (ICAO) for four different thrust levels (Idle, approach, cruise and take-off). It is a common procedure to use this data base as a starting point to estimate aircraft emissions at airports and further on to calculate the contribution of airports on local air quality. The comparison of these indices to real in use measurements therefore is a vital task to test the quality of air quality models at airports. Here a method to determine emission indices is used, where concentration measurements of CO2 together with other pollutants in the aircraft plume are needed. During intensive measurement campaigns at Zurich (ZRH) and Paris Charles De Gaulle (CDG) airports, concentrations of CO2, NO, NO2 and CO were measured. The measurement techniques were Fourier-Transform-Infrared (FTIR) spectrometry and Differential Optical Absorption Spectroscopy (DOAS). The big advantage of these methods is that no operations on the airport are influenced during measurement times. Together with detailed observations of taxiway movements, a comparison of emission indices with real in use emissions is possible.

  18. Conversion of the exhaust emission results obtained from combustion engines of heavy-duty vehicles

    NASA Astrophysics Data System (ADS)

    Merkisz, J.; Pielecha, J.

    2016-09-01

    The use of internal combustion engines as the drive for heavy-duty vehicles forces these engines to be tested on an engine dynamometer. Thus, these engines operate under forced conditions, which are significantly different from their actual application. To assess the ecology of such vehicles (or more accurately the engine alone) the emission of pollution per unit of work done by the engine must be determined. However, obtaining the results of unit emissions (expressed in grams of the compound per a unit of performed work) does not give the grounds for determining the mass of pollutants on a given stretch of the road travelled by the vehicle. Therefore, there is a need to change the emission value expressed in units referenced to the engine work into a value of road emissions. The paper presents a methodology of determining pollutant emissions of heavy-duty road vehicles on the basis of the unit emissions, as well as additional parameters determined on the basis of the algorithm presented in the article. A solution was obtained that can be used not only for heavy-duty vehicles, but was also extended to allow use for buses.

  19. Performance and exhaust emission characteristics of variable compression ratio diesel engine fuelled with esters of crude rice bran oil.

    PubMed

    Vasudeva, Mohit; Sharma, Sumeet; Mohapatra, S K; Kundu, Krishnendu

    2016-01-01

    As a substitute to petroleum-derived diesel, biodiesel has high potential as a renewable and environment friendly energy source. For petroleum importing countries the choice of feedstock for biodiesel production within the geographical region is a major influential factor. Crude rice bran oil is found to be good and viable feedstock for biodiesel production. A two step esterification is carried out for higher free fatty acid crude rice bran oil. Blends of 10, 20 and 40 % by vol. crude rice bran biodiesel are tested in a variable compression ratio diesel engine at compression ratio 15, 16, 17 and 18. Engine performance and exhaust emission parameters are examined. Cylinder pressure-crank angle variation is also plotted. The increase in compression ratio from 15 to 18 resulted in 18.6 % decrease in brake specific fuel consumption and 14.66 % increase in brake thermal efficiency on an average. Cylinder pressure increases by 15 % when compression ratio is increased. Carbon monoxide emission decreased by 22.27 %, hydrocarbon decreased by 38.4 %, carbon dioxide increased by 17.43 % and oxides of nitrogen as NOx emission increased by 22.76 % on an average when compression ratio is increased from 15 to 18. The blends of crude rice bran biodiesel show better results than diesel with increase in compression ratio.

  20. Effect of exhaust gas recirculation on emissions from a flame-tube combustor using Liquid Jet A fuel

    NASA Technical Reports Server (NTRS)

    Marek, C. J.; Tacina, R. R.

    1976-01-01

    The effects of uncooled exhaust gas recirculation as an inert diluent on emissions of oxides of nitrogen (NO + NO2) and on combustion efficiency were investigated. Ratios of recirculated combustion products to inlet airflow were varied from 10 to 80 percent by using an inlet air ejector nozzle. Liquid Jet A fuel was used. The flame-tube combustor was 10.2 cm in diameter. It was operated with and without a flameholder present. The combustor pressure was maintained constant at 0.5 MPa. The equivalence ratio was varied from 0.3 to 1.0. The inlet air temperature was varied from 590 to 800 K, and the reference velocity from 10 to 30 m/sec. Increasing the percent recirculation from 10 to 25 had the following effects: (1) the peak NOx emission was decreased by 37 percent, from 8 to 5 g NO2/kg fuel, at an inlet air temperature of 590 K and a reference velocity of 15 m/sec; (2) the combustion efficiency was increased, particularly at the higher equivalence ratios; and (3) for a high combustion efficiency of greater than 99.5 percent, the range of operation of the combustor was nearly doubled in terms of equivalence ratio. Increasing the recirculation from 25 to 50 percent did not change the emissions significantly.

  1. Determination of major combustion products in aircraft exhausts by FTIR emission spectroscopy

    NASA Astrophysics Data System (ADS)

    Heland, J.; Schäfer, K.

    The results of ground-based FTIR emission measurements of major combustion products such as CO 2, H 2O, CO, NO, and N 2O of in-service aircraft engines are reported and compared to values published in recent literature. About 25% differences in the NO and CO emission indices at several power settings were found for two military bypass engines of the same type. In addition the measured CO emission index of (51.8±4.6) g kg -1 at idle power of a CFM56-3 engine was about 27% lower than the value given by Spicer et al. (1984, 1994)for this engine type and about 27-48% higher than the ICAO data ( ICAO, 1995) for the whole span of CFM56-3 engines. The CO emission index measured at idle power of a CFM56-5C2 engine of AN Airbus A340 was (24±4) g kg -1 and can be compared to the ICAO value of 34 g kg -1. The N 2O mixing ratios measured at a higher power setting of this engine was found to be 4 ppm and is in the range of reported literature values. Since the NO and CO emissions are strongly connected to the combustion process/efficiency and thus to the state of engine maintainance and/or the engine age, it can be concluded that there are significant engine-to-engine (of the same type) and possibly day-to-day variations in the emission characteristics of aero engines which cannot be neglected for the estimation of the overall air-traffic emissions.

  2. Effects of fuels, engine load and exhaust after-treatment on diesel engine SVOC emissions and development of SVOC profiles for receptor modeling.

    PubMed

    Huang, Lei; Bohac, Stanislav V; Chernyak, Sergei M; Batterman, Stuart A

    2015-02-01

    Diesel exhaust emissions contain numerous semivolatile organic compounds (SVOCs) for which emission information is limited, especially for idling conditions, new fuels and the new after-treatment systems. This study investigates exhaust emissions of particulate matter (PM), polycyclic aromatic hydrocarbons (PAHs), nitro-PAHs (NPAHs), and sterane and hopane petroleum biomarkers from a heavy-duty (6.4 L) diesel engine at various loads (idle, 600 and 900 kPa BMEP), with three types of fuel (ultra-low sulfur diesel or ULSD, Swedish low aromatic diesel, and neat soybean biodiesel), and with and without a diesel oxidation catalyst (DOC) and diesel particulate filter (DPF). Swedish diesel and biodiesel reduced emissions of PM2.5, Σ15PAHs, Σ11NPAHs, Σ5Hopanes and Σ6Steranes, and biodiesel resulted in the larger reductions. However, idling emissions increased for benzo[k]fluoranthene (Swedish diesel), 5-nitroacenaphthene (biodiesel) and PM2.5 (biodiesel), a significant result given the attention to exposures from idling vehicles and the toxicity of high-molecular-weight PAHs and NPAHs. The DOC + DPF combination reduced PM2.5 and SVOC emissions during DPF loading (>99% reduction) and DPF regeneration (83-99%). The toxicity of diesel exhaust, in terms of the estimated carcinogenic risk, was greatly reduced using Swedish diesel, biodiesel fuels and the DOC + DPF. PAH profiles showed high abundances of three and four ring compounds as well as naphthalene; NPAH profiles were dominated by nitro-naphthalenes, 1-nitropyrene and 9-nitroanthracene. Both the emission rate and the composition of diesel exhaust depended strongly on fuel type, engine load and after-treatment system. The emissions data and chemical profiles presented are relevant to the development of emission inventories and exposure and risk assessments.

  3. Effects of fuels, engine load and exhaust after-treatment on diesel engine SVOC emissions and development of SVOC profiles for receptor modeling

    PubMed Central

    Huang, Lei; Bohac, Stanislav V.; Chernyak, Sergei M.; Batterman, Stuart A.

    2015-01-01

    Diesel exhaust emissions contain numerous semivolatile organic compounds (SVOCs) for which emission information is limited, especially for idling conditions, new fuels and the new after-treatment systems. This study investigates exhaust emissions of particulate matter (PM), polycyclic aromatic hydrocarbons (PAHs), nitro-PAHs (NPAHs), and sterane and hopane petroleum biomarkers from a heavy-duty (6.4 L) diesel engine at various loads (idle, 600 and 900 kPa BMEP), with three types of fuel (ultra-low sulfur diesel or ULSD, Swedish low aromatic diesel, and neat soybean biodiesel), and with and without a diesel oxidation catalyst (DOC) and diesel particulate filter (DPF). Swedish diesel and biodiesel reduced emissions of PM2.5, Σ15PAHs, Σ11NPAHs, Σ5Hopanes and Σ6Steranes, and biodiesel resulted in the larger reductions. However, idling emissions increased for benzo[k]fluoranthene (Swedish diesel), 5-nitroacenaphthene (biodiesel) and PM2.5 (biodiesel), a significant result given the attention to exposures from idling vehicles and the toxicity of high-molecular-weight PAHs and NPAHs. The DOC + DPF combination reduced PM2.5 and SVOC emissions during DPF loading (>99% reduction) and DPF regeneration (83–99%). The toxicity of diesel exhaust, in terms of the estimated carcinogenic risk, was greatly reduced using Swedish diesel, biodiesel fuels and the DOC + DPF. PAH profiles showed high abundances of three and four ring compounds as well as naphthalene; NPAH profiles were dominated by nitro-naphthalenes, 1-nitropyrene and 9-nitroanthracene. Both the emission rate and the composition of diesel exhaust depended strongly on fuel type, engine load and after-treatment system. The emissions data and chemical profiles presented are relevant to the development of emission inventories and exposure and risk assessments. PMID:25709535

  4. Effects of fuels, engine load and exhaust after-treatment on diesel engine SVOC emissions and development of SVOC profiles for receptor modeling

    NASA Astrophysics Data System (ADS)

    Huang, Lei; Bohac, Stanislav V.; Chernyak, Sergei M.; Batterman, Stuart A.

    2015-02-01

    Diesel exhaust emissions contain numerous semivolatile organic compounds (SVOCs) for which emission information is limited, especially for idling conditions, new fuels and the new after-treatment systems. This study investigates exhaust emissions of particulate matter (PM), polycyclic aromatic hydrocarbons (PAHs), nitro-PAHs (NPAHs), and sterane and hopane petroleum biomarkers from a heavy-duty (6.4 L) diesel engine at various loads (idle, 600 and 900 kPa BMEP), with three types of fuel (ultra-low sulfur diesel or ULSD, Swedish low aromatic diesel, and neat soybean biodiesel), and with and without a diesel oxidation catalyst (DOC) and diesel particulate filter (DPF). Swedish diesel and biodiesel reduced emissions of PM2.5, Σ15PAHs, Σ11NPAHs, Σ5Hopanes and Σ6Steranes, and biodiesel resulted in the larger reductions. However, idling emissions increased for benzo[k]fluoranthene (Swedish diesel), 5-nitroacenaphthene (biodiesel) and PM2.5 (biodiesel), a significant result given the attention to exposures from idling vehicles and the toxicity of high-molecular-weight PAHs and NPAHs. The DOC + DPF combination reduced PM2.5 and SVOC emissions during DPF loading (>99% reduction) and DPF regeneration (83-99%). The toxicity of diesel exhaust, in terms of the estimated carcinogenic risk, was greatly reduced using Swedish diesel, biodiesel fuels and the DOC + DPF. PAH profiles showed high abundances of three and four ring compounds as well as naphthalene; NPAH profiles were dominated by nitronaphthalenes, 1-nitropyrene and 9-nitroanthracene. Both the emission rate and the composition of diesel exhaust depended strongly on fuel type, engine load and after-treatment system. The emissions data and chemical profiles presented are relevant to the development of emission inventories and exposure and risk assessments.

  5. Polycyclic aromatic hydrocarbon emissions in diesel exhaust using gas chromatography-mass spectrometry with programmed temperature vaporization and large volume injection

    NASA Astrophysics Data System (ADS)

    Vieira de Souza, Carolina; Corrêa, Sergio Machado

    2015-02-01

    Diesel engines are significant sources of Polycyclic Aromatic Compounds (PAHs) in urban atmospheres. These compounds are widely known for their carcinogenic potential and mutagenic properties. In this study, a method was developed for the analysis of 16 priorities PAHs using gas chromatography-mass spectrometry (GC-MS) with programmable temperature vaporizer large volume injection (PTV-LVI), which allowed to be obtained detection limits below 2.0 ng mL-1. This method was evaluated in samples from stratified particulate matter and gas phase from the emissions of diesel vehicle employing diesel commercial S10 (sulfur 10 mg L-1) and B5 (biodiesel 5% v/v). A sampling system that does not employ exhaust products dilution was used to evaluate the PAHs gas-particle partition. Six PAHs were identified in extracts and gas-phase PAHs took percentage of 80% in the total PAHs emissions. The sampling system without dilution not caused a strong nucleation/condensation of the most volatile PAHs. PAHs size-particle distribution was found in higher levels in the accumulation mode.

  6. Spatial and temporal allocation of ship exhaust emissions in Australian coastal waters using AIS data: Analysis and treatment of data gaps

    NASA Astrophysics Data System (ADS)

    Goldsworthy, Brett

    2017-08-01

    Ship exhaust emissions need to be allocated accurately in both space and time in order to examine many of the associated impacts, including on air quality and health. Data on ship activity from the Automatic Identification System (AIS) allow ship exhaust emissions to be calculated with fine spatial and temporal resolution. However, there are spatial gaps in the coverage afforded by the coastal network of ground stations that are used to collect the AIS data. This paper focuses on the problem of allocating emissions to the coastal gap regions. Allocating emissions to these regions involves generating interpolated ship tracks that both span the gaps and avoid coming too close to land. In most cases, a simple shortest path or straight line interpolation produces tracks that do not overlap or come too close to land. Where the simple method does not produce acceptable results, vessel tracks are steered around land on shortest available paths using a combination of visibility graphs and Dijkstra's algorithm. A geographical cluster analysis is first used to identify the boundary regions of the data gaps. The properties of the data gaps are summarised in terms of the length, duration and speed of the spanning tracks. The interpolation methods are used to improve the spatial distribution of emissions. It is also shown that emissions in the gap regions can contribute substantially to the total ship exhaust emissions in close proximity to highly populated areas.

  7. 78 FR 63015 - Exhaust Emissions Standards for New Aircraft Gas Turbine Engines and Identification Plate for...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-10-23

    ...The FAA is making technical changes to a final rule published in the Federal Register on December 31, 2012. That final rule amended the emission standards for certain turbine engine powered airplanes to incorporate the standards promulgated by the United States Environmental Protection Agency (EPA) on June 18, 2012. The final rule contained six minor technical errors: One in the authority citation, and five in tables listing the emissions standards for engines manufactured on and after July 18, 2012. In addition, we are correcting an error in a definition that existed before the final rule and was overlooked. The FAA is issuing this technical amendment to correct these errors.

  8. Gas-particle partitioning of primary organic aerosol emissions: (1) Gasoline vehicle exhaust

    NASA Astrophysics Data System (ADS)

    May, Andrew A.; Presto, Albert A.; Hennigan, Christopher J.; Nguyen, Ngoc T.; Gordon, Timothy D.; Robinson, Allen L.

    2013-10-01

    The gas-particle partitioning of the primary organic aerosol (POA) emissions from fifty-one light-duty gasoline vehicles (model years 1987-2012) was investigated at the California Air Resources Board Haagen-Smit Laboratory. Each vehicle was operated over the cold-start unified cycle on a chassis dynamometer and its emissions were sampled using a constant volume sampler. Four independent yet complementary approaches were used to investigate POA gas-particle partitioning: sampling artifact correction of quartz filter data, dilution from the constant volume sampler into a portable environmental chamber, heating in a thermodenuder, and thermal desorption/gas chromatography/mass spectrometry analysis of quartz filter samples. This combination of techniques allowed gas-particle partitioning measurements to be made across a wide range of atmospherically relevant conditions - temperatures of 25-100 °C and organic aerosol concentrations of <1-600 μg m-3. The gas-particle partitioning of the POA emissions varied continuously over this entire range of conditions and essentially none of the POA should be considered non-volatile. Furthermore, for most vehicles, the low levels of dilution used in the constant volume sampler created particle mass concentrations that were greater than a factor of 10 or higher than typical ambient levels. This resulted in large and systematic partitioning biases in the POA emission factors compared to more dilute atmospheric conditions, as the POA emission rates may be over-estimated by nearly a factor of four due to gas-particle partitioning at higher particle mass concentrations. A volatility distribution was derived to quantitatively describe the measured gas-particle partitioning data using absorptive partitioning theory. Although the POA emission factors varied by more than two orders of magnitude across the test fleet, the vehicle-to-vehicle differences in gas-particle partitioning were modest. Therefore, a single volatility distribution

  9. Regulated and unregulated exhaust emissions from two three-way catalyst equipped gasoline fuelled vehicles

    NASA Astrophysics Data System (ADS)

    Westerholm, Roger; Christensen, Anders; Rosén, Åke

    This investigation presents emission factors of both regulated (CO, HC, NO x and particulate) and unregulated pollutants (aldehydes, monocyclic aromatic compounds and polycyclic aromatic compounds) measured under three different driving conditions, i.e. cold transient, stabilised and hot transient. These three driving conditions were simulated using the US FTP-75 driving cycle. Two three-way catalyst equipped light duty passenger cars were investigated. As expected, a higher emission of both regulated and unregulated pollutants was observed in the cold start phase of the driving cycle.

  10. Approach to SSME health monitoring. III - Exhaust plume emission spectroscopy: Recent results and detailed analysis

    NASA Astrophysics Data System (ADS)

    Tejwani, Gopal D.; van Dyke, David B.; Bircher, Felix E.

    1993-06-01

    Spectral data for two recent A-1 test firings, 901-717 and 901-718, obtained from an Optical Multichannel Analyzer and an Optical Plume Anomaly Detector, are presented. The spectral data encompasses the database of SSME critical components and materials and the spectral database for the SSME related elements and materials. Relatively strong and continuous emissions from Cr and Fe atomic transitions were observed starting at engine start plus 494 s and persisting until the engine shut off at engine start plus 520 s. These emissions are considered to be emanated from the SSME material AISI 440C, which is traced to high pressure turbopump bearings.

  11. 40 CFR 86.1823-01 - Durability demonstration procedures for exhaust emissions.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ...), bench aging of individual components or systems, or other approaches approved by the Administrator. (A) For whole vehicle mileage accumulation programs, all emission control components and systems... period. (B) Bench procedures shall simulate the aging of components or systems over the applicable...

  12. 40 CFR 86.1823-01 - Durability demonstration procedures for exhaust emissions.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ...-use driving), bench aging of individual components or systems, or other approaches approved by the Administrator. (A) For whole vehicle mileage accumulation programs, all emission control components and systems... period. (B) Bench procedures shall simulate the aging of components or systems over the applicable...

  13. 40 CFR 86.1823-01 - Durability demonstration procedures for exhaust emissions.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ...-use driving), bench aging of individual components or systems, or other approaches approved by the Administrator. (A) For whole vehicle mileage accumulation programs, all emission control components and systems... period. (B) Bench procedures shall simulate the aging of components or systems over the applicable...

  14. 40 CFR 86.1823-01 - Durability demonstration procedures for exhaust emissions.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ...-use driving), bench aging of individual components or systems, or other approaches approved by the Administrator. (A) For whole vehicle mileage accumulation programs, all emission control components and systems... period. (B) Bench procedures shall simulate the aging of components or systems over the applicable...

  15. 40 CFR 86.1823-01 - Durability demonstration procedures for exhaust emissions.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ...-use driving), bench aging of individual components or systems, or other approaches approved by the Administrator. (A) For whole vehicle mileage accumulation programs, all emission control components and systems... period. (B) Bench procedures shall simulate the aging of components or systems over the applicable...

  16. 40 CFR 86.1823-08 - Durability demonstration procedures for exhaust emissions.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... vehicles or vehicles which do not use a catalyst as the principle after-treatment emission control device. This procedure requires installation of the catalyst-plus-oxygen-sensor system on a catalyst aging... time calculated from the bench aging time (BAT) equation. The BAT equation requires, as input,...

  17. 40 CFR 87.64 - Sampling and analytical procedures for measuring gaseous exhaust emissions.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... along with your emission levels of regulated NOX to the Administrator for engines of a type or model of... Administrator for engines currently in production and of a type or model for which the date of manufacture of... AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) CONTROL OF AIR POLLUTION FROM AIRCRAFT AND AIRCRAFT ENGINES...

  18. 40 CFR 1042.101 - Exhaust emission standards for Category 1 engines and Category 2 engines.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR POLLUTION CONTROLS CONTROL OF EMISSIONS FROM NEW AND IN-USE... fuels containing 15 ppm or less sulfur (ultra low-sulfur diesel fuel). Manufacturers may use low-sulfur diesel fuel (without request) to certify an engine otherwise requiring an ultra low-sulfur test fuel...

  19. 40 CFR 1051.103 - What are the exhaust emission standards for snowmobiles?

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... AGENCY (CONTINUED) AIR POLLUTION CONTROLS CONTROL OF EMISSIONS FROM RECREATIONAL ENGINES AND VEHICLES... functional relationship. Choose your corporate average HC and CO standards for each year according to the... percent; that is, that the standards comply with the following equation: ER25JN08.006 (ii) Your corporate...

  20. Metal particle emissions in the exhaust stream of diesel engines: an electron microscope study.

    PubMed

    Liati, Anthi; Schreiber, Daniel; Dimopoulos Eggenschwiler, Panayotis; Arroyo Rojas Dasilva, Yadira

    2013-12-17

    Scanning electron microscopy and transmission electron microscopy were applied to investigate the morphology, mode of occurrence and chemical composition of metal particles (diesel ash) in the exhaust stream of a small truck outfitted with a typical after-treatment system (a diesel oxidation catalyst (DOC) and a downstream diesel particulate filter (DPF)). Ash consists of Ca-Zn-P-Mg-S-Na-Al-K-phases (lube-oil related), Fe, Cr, Ni, Sn, Pb, Sn (engine wear), and Pd (DOC coating). Soot agglomerates of variable sizes (<0.5-5 μm) are abundant upstream of the DPF and are ash-free or contain notably little attached ash. Post-DPF soot agglomerates are very few, typically large (>1-5 μm, exceptionally 13 μm), rarely <0.5 μm, and contain abundant ash carried mostly from inside the DPF. The ash that reaches the atmosphere also occurs as separate aggregates ca. 0.2-2 μm in size consisting of sintered primary phases, ca. 20-400 nm large. Insoluble particles of these sizes may harm the respiratory and cardiovascular systems. The DPF probably promotes breakout of large soot agglomerates (mostly ash-bearing) by favoring sintering. Noble metals detached from the DOC coating may reach the ambient air. Finally, very few agglomerates of Fe-oxide nanoparticles form newly from engine wear and escape into the atmosphere.