Drying kinetics and mathematical modeling of hot air drying of coconut coir pith.

PubMed

Fernando, J A K M; Amarasinghe, A D U S

2016-01-01

Drying kinetics of coir pith was studied and the properties of compressed coir pith discs were analyzed. Coir pith particles were oven dried in the range of temperatures from 100 to 240 °C and the rehydration ability of compressed coir pith was evaluated by finding the volume expansion. The optimum drying temperature was found to be 140 °C. Hot air drying was carried out to examine the drying kinetics by allowing the coir pith particles to fluidize and circulate inside the drying chamber. Particle motion within the drying chamber closely resembled the particle motion in a flash dryer. The effective moisture diffusivity was found to increase from 1.18 × 10(-8) to 1.37 × 10(-8) m(2)/s with the increase of air velocity from 1.4 to 2.5 m/s respectively. Correlation analysis and residual plots were used to determine the adequacy of existing mathematical models for describing the drying behavior of coir pith. The empirical models, Wang and Singh model and Linear model, were found to be adequate for accurate prediction of drying behavior of coir pith. A new model was proposed by modifying the Wang and Singh model and considering the effect of air velocity. It gave the best correlation between observed and predicted moisture ratio with high value of coefficient of determination (R(2)) and lower values of root mean square error, reduced Chi square (χ(2)) and mean relative deviation (E%).

Prospects for the commercial development of hot dry rock geothermal energy in New Mexico

NASA Astrophysics Data System (ADS)

Duchane, D. V.; Goff, F.

A vast store of energy is available to the world in the form of hot dry rock (HDR) which exists almost everywhere beneath the surface of the earth. The Los Alamos National Laboratory has developed technology to mine the heat from HDR by using techniques developed in the petroleum industry. In practice, an artificial reservoir is created in the hot rock and water is circulated through the reservoir to extract the thermal energy and bring it to the surface. There are virtually no adverse environmental effects from an HDR plant when the system is operated in a closed-loop mode with the process water continually recirculated. An experimental plant at Fenton Hill, NM is now undergoing long-term testing to demonstrate that energy can be obtained from HDR on a sustained basis with operational procedures which are readily adaptable to industry. Significant HDR resources exist in the state of New Mexico. Resources in the Valles Caldera, Zuni Uplift, and Rio Grande Rift have been evaluated in detail. Studies indicate that it should be possible to economically develop high grade HDR resources with technology available today. As advanced concepts for developing and operating HDR systems are investigated, even more widespread utilization of the technology will be commercially feasible.

Induced Seismicity at the UK "Hot Dry Rock" Test Site for Geothermal Energy Production

NASA Astrophysics Data System (ADS)

Li, Xun; Main, Ian; Jupe, Andrew

2018-03-01

In enhanced geothermal systems (EGS), fluid is injected at high pressure in order to stimulate fracturing and/or fluid flow through otherwise relatively impermeable underlying hot rocks to generate power and/or heat. The stimulation induces micro-earthquakes whose precise triggering mechanism and relationship to new and pre-existing fracture networks are still the subject of some debate. Here we analyse the dataset for induced micro-earthquakes at the UK "hot dry rock" experimental geothermal site (Rosemanowes, Cornwall). We quantify the evolution of several metrics used to characterise induced seismicity, including the seismic strain partition factor and the "seismogenic index". The results show a low strain partition factor of 0.01% and a low seismogenenic index indicating that aseismic processes dominate. We also analyse the spatio-temporal distribution of hypocentres, using simple models for the evolution of hydraulic diffusivity by (a) isotropic and (b) anisotropic pore-pressure relaxation. The principal axes of the diffusivity or permeability tensor inferred from the spatial distribution of earthquake foci are aligned parallel to the present-day stress field, although the maximum permeability is vertical, whereas the maximum principal stress is horizontal. Our results are consistent with a triggering mechanism that involves (a) seismic shear slip along optimally-oriented pre-existing fractures, (b) a large component of aseismic slip with creep (c) activation of tensile fractures as hydraulic conduits created by both the present-day stress field and by the induced shear slip, both exploiting pre-existing joint sets exposed in borehole data.

Energy Design Guidelines for High Performance Schools: Hot and Dry Climates.

ERIC Educational Resources Information Center

Department of Energy, Washington, DC. Office of Energy Efficiency and Renewable Energy.

This guide contains recommendations for designing high performance, energy efficient schools located in hot and dry climates. A high performance checklist for designers is included along with several case studies of projects that successfully demonstrated high performance design solutions for hot and dry climates. The guide's 10 sections…

Drying and decontamination of pistachios with sequential infrared drying, tempering and hot air drying

USDA-ARS?s Scientific Manuscript database

The pistachio industry is in need of improved drying technology as the current hot air drying has low energy efficiency and drying rate and high labor cost and also does not produce safe products against microbial contamination. In the current study, dehulled and water- sorted pistachios with a mois...

Geothermal energy - Ready for use

NASA Astrophysics Data System (ADS)

Miskell, J. T.

1980-11-01

The use of geothermal energy in the United States for heating applications is discussed. The three major forms of geothermal energy, hydrothermal, pertrothermal and geopressured, are briefly reviewed, with attention given to the types of energy available from each. Federally supported projects demonstrating the use of geothermal hot water to heat homes in Boise, Idaho, and hot dry rocks in Fenton Hill, New Mexico to produce electricity are presented. Data available from existing geothermal energy applications are presented which show that geothermal is cost competitive with conventional energy sources using existing technology, and government economic incentives to the producers and users of geothermal energy are indicated. Finally, advanced equipment currently under development for the generation of electricity from geothermal resources at reduced costs is presented.

Sample storage-induced changes in the quantity and quality of soil labile organic carbon

PubMed Central

Sun, Shou-Qin; Cai, Hui-Ying; Chang, Scott X.; Bhatti, Jagtar S.

2015-01-01

Effects of sample storage methods on the quantity and quality of labile soil organic carbon are not fully understood even though their effects on basic soil properties have been extensively studied. We studied the effects of air-drying and frozen storage on cold and hot water soluble organic carbon (WSOC). Cold- and hot-WSOC in air-dried and frozen-stored soils were linearly correlated with those in fresh soils, indicating that storage proportionally altered the extractability of soil organic carbon. Air-drying but not frozen storage increased the concentrations of cold-WSOC and carbohydrate in cold-WSOC, while both increased polyphenol concentrations. In contrast, only polyphenol concentration in hot-WSOC was increased by air-drying and frozen storage, suggesting that hot-WSOC was less affected by sample storage. The biodegradability of cold- but not hot-WSOC was increased by air-drying, while both air-drying and frozen storage increased humification index and changed specific UV absorbance of both cold- and hot-WSOC, indicating shifts in the quality of soil WSOC. Our results suggest that storage methods affect the quantity and quality of WSOC but not comparisons between samples, frozen storage is better than air-drying if samples have to be stored, and storage should be avoided whenever possible when studying the quantity and quality of both cold- and hot-WSOC. PMID:26617054

Induced seismicity at the UK `hot dry rock' test site for geothermal energy production

NASA Astrophysics Data System (ADS)

Li, Xun; Main, Ian; Jupe, Andrew

2018-07-01

In enhanced geothermal systems (EGS), fluid is injected at high pressure in order to stimulate fracturing and/or fluid flow through otherwise relatively impermeable underlying hot rocks to generate power and/or heat. The stimulation induces microearthquakes whose precise triggering mechanism and relationship to new and pre-existing fracture networks are still the subject of some debate. Here, we analyse the data set for induced microearthquakes at the UK `hot dry rock' experimental geothermal site (Rosemanowes, Cornwall). We quantify the evolution of several metrics used to characterise induced seismicity, including the seismic strain partition factor and the `seismogenic index'. The results show a low strain partition factor of 0.01 per cent and a low seismogenic index indicating that aseismic processes dominate. We also analyse the spatio-temporal distribution of hypocentres, using simple models for the evolution of hydraulic diffusivity by (1) isotropic and (2) anisotropic pore-pressure relaxation. The principal axes of the diffusivity or permeability tensor inferred from the spatial distribution of earthquake foci are aligned parallel to the present-day stress field, although the maximum permeability is vertical, whereas the maximum principal stress is horizontal. Our results are consistent with a triggering mechanism that involves (1) seismic shear slip along optimally oriented pre-existing fractures, (2) a large component of aseismic slip with creep and (3) activation of tensile fractures as hydraulic conduits created by both the present-day stress field and by the induced shear slip, both exploiting pre-existing joint sets exposed in borehole data.

System for drying and heating particulate coal

DOE Office of Scientific and Technical Information (OSTI.GOV)

Offergeld, E.; Wischniewski, M.

1978-04-04

Wet particulate coal and a current of hot dry gas at superatmospheric pressure are introduced into a substantially closed drying chamber to contact the material with the gas while maintaining the drying chamber under superatmospheric pressure so that the material is dried by the gas. The dried material is withdrawn from the drying chamber and the gas is withdrawn from the drying chamber and itself mixed with a stream of hot dry gas produced by burning a combustible and a combustion-supporting gas. This mixture is then reintroduced into the drying chamber as the current of hot gas used to drymore » the coal. The burner is operated at superatmospheric pressure and is formed of a jet-pump type injector, and a diffusor is provided downstream of this injector in the circulation path.« less

Retrofitting Air Conditioning and Duct Systems in Hot, Dry Climates

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shapiro, C.; Aldrich, R.; Arena, L.

2012-07-01

This technical report describes CARB's work with Clark County Community Resources Division in Las Vegas, Nevada, to optimize procedures for upgrading cooling systems on existing homes in the area to implement health, safety, and energy improvements. Detailed monitoring of five AC systems showed that three of the five systems met or exceeded air flow rate goals.

Hot dry rock geothermal energy development program. Semiannual report, October 1, 1978-March 31, 1979

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brown, M.C.; Nunz, G.J.; Cremer, G.M.

1979-09-01

The potential of energy extracted from hot dry rock (HDR) was investigated as a commercailly feasible alternate energy source. Run Segments 3 and 4 were completed in the prototype reservoir of the Phase I energy-extraction system at Fenton Hill, New Mexico. Results of these tests yielded significant data on the existing system and this information will be applicable to future HDR systems. Plans and operations initiating a Phase II system are underway at the Fenton Hill site. This system, a deeper, hotter commercial-size reservoir, is intended to demonstrate the longevity and economics of an HDR system. Major activity occurred inmore » evaluation of the national resource potential and in characterizing possible future HDR geothermal sites. Work has begun in the institutional and industrial support area to assess the economics and promote commercial interest in HDR systems as an alternate energy source.« less

[Comparison of sulfur fumigation processing and direct hot air heating technology on puerarin contents and efficacy of Puerariae Thomsonii Radix].

PubMed

Yu, Hong-Li; Zhang, Qian; Jin, Yang-Ping; Wang, Kui-Long; Lu, Tu-Lin; Li, Lin

2016-07-01

In order to compare the effect of sulfur fumigation processing and direct hot air heating technology on puerarin contents and efficacy of Puerariae Thomsonii Radix, the fresh roots of Pueraria thomsonii were cut into small pieces and prepared into direct sunshine drying samples, direct hot air drying samples, and sulfur fumigation-hot air drying samples. Moisture contents of the samples were then determined. The puerarin contents of different samples were compared by HPLC method. Moreover, the models of drunkenness mice were established, and then with superoxide dismutase (SOD) content as the index, aqueous decoction extracts of Puerariae Thomsonii Radix samples with sulfur fumigation processing and non-sulfur fumigation processing methods were administrated by ig; the effects of sulfur fumigation on contents of SOD in mice liver and serum were determined, and the sulfur fumigation samples and non-sulfur fumigation samples were investigated for moth and mildew under different packaging and storage conditions. Results showed that the sulfur fumigation samples significantly changed the puerarin content from Puerariae Thomsonii Radix. The content of puerarin was decreased gradually when increasing the times of sulfur fumigation and amount of sulfur. SOD content in drunken mice liver and serum was significantly decreased when increasing the times of sulfur fumigation, showing significant difference with both direct sunshine drying group and direct hot air drying group. Moth and mildew were not found in the sulfur fumigation samples and direct hot air drying samples whose moisture contents were lower than the limit in Pharmacopoeia. Research showed that sulfur fumigation can significantly reduce the content of main active ingredients and reduce the efficacy of Puerariae Thomsonii Radix, indicating that the quality of Puerariae Thomsonii Radix was significantly decreased after sulfur fumigation. However, the contents of the main active ingredients, efficacy and storage results of the direct hot air drying samples were similar to those in direct sunshine drying samples, so the hot air drying process was a nice drying technology which could be promoted for use. Copyright© by the Chinese Pharmaceutical Association.

Ultrasound-Assisted Hot Air Drying of Foods

NASA Astrophysics Data System (ADS)

Mulet, Antonio; Cárcel, Juan Andrés; García-Pérez, José Vicente; Riera, Enrique

This chapter deals with the application of power ultrasound, also named high-intensity ultrasound, in the hot air drying of foods. The aim of ultrasound-assisted drying is to overcome some of the limitations of traditional convective drying systems, especially by increasing drying rate without reducing quality attributes. The effects of ultrasound on drying rate are responsible for some of the phenomena produced in the internal and/or external resistance to mass transfer.

Impact of postharvest drying conditions on in vitro starch digestibility and estimated glycemic index of cooked non-waxy long-grain rice (Oryza sativa L.).

PubMed

Donlao, Natthawuddhi; Ogawa, Yukiharu

2017-02-01

Wet paddy needs to be dried to reduce its moisture content after harvesting. In this study, effects of postharvest drying condition on in vitro starch digestibility and estimated glycemic index of cooked rice (Oryza sativa L.) were investigated. Varying drying conditions, i.e. hot-air drying at 40, 65, 90 and 115 °C, and sun drying were applied to raw paddy. After husking and polishing, polished grains were cooked using an electric rice cooker. Cooked samples were analyzed for their moisture content and amount of resistant and total starch. Five samples in both intact grain and slurry were digested under simulated in vitro gastrointestinal digestion process. The in vitro starch digestion rate was measured and the hydrolysis index (HI) and estimated glycemic index (eGI) were calculated. Cooked rice obtained from hot-air drying showed relatively lower HI and eGI than that obtained from sun-drying. Among samples from hot-air drying treatment, eGI of cooked rice decreased with increasing drying temperature, except for the drying temperature of 115 °C. As a result, cooked rice from the hot-air drying at 90 °C showed lowest eGI. The results indicated that cooked rice digestibility was affected by postharvest drying conditions. © 2016 Society of Chemical Industry. © 2016 Society of Chemical Industry.

Formative Assessment Probes: Wet Jeans

ERIC Educational Resources Information Center

Keeley, Page

2015-01-01

Picture a wet towel or a puddle of water on a hot, sunny day. An hour later, the towel is dry and the puddle no longer exists. What happened to the water? Where did it go? These are questions that reveal myriad interesting student ideas about evaporation and the water cycle--ideas that provide teachers with a treasure trove of data they can use to…

Intensification of hot extremes in the United States

DOE Office of Scientific and Technical Information (OSTI.GOV)

Diffenbaugh, Noah; Ashfaq, Moetasim

Governments are currently considering policies that will limit greenhouse gas concentrations, including negotiation of an international treaty to replace the expiring Kyoto Protocol. Existing mitigation targets have arisen primarily from political negotiations, and the ability of such policies to avoid dangerous impacts is still uncertain. Using a large suite of climate model experiments, we find that substantial intensification of hot extremes could occur within the next 3 decades, below the 2 C global warming target currently being considered by policy makers. We also find that the intensification of hot extremes is associated with a shift towards more anticyclonic atmospheric circulationmore » during the warm season, along with warm-season drying over much of the U.S. The possibility that intensification of hot extremes could result from relatively small increases in greenhouse gas concentrations suggests that constraining global warming to 2 C may not be sufficient to avoid dangerous climate change.« less

Effect of hot air drying on volatile compounds of Flammulina velutipes detected by HS-SPME-GC-MS and electronic nose.

PubMed

Yang, Wenjian; Yu, Jie; Pei, Fei; Mariga, Alfred Mugambi; Ma, Ning; Fang, Yong; Hu, Qiuhui

2016-04-01

Volatile compounds are important factors that affect the flavor quality of Flammulina velutipes, but the changes occurring during hot air drying is still unclear. To clarify the dynamic changes of flavor components during hot air drying, comprehensive flavor characterization and volatile compounds of F. velutipes were evaluated using electronic nose technology and headspace solid phase micro-extraction combined with gas chromatography-mass spectrometry (HS-SPME-GC-MS), respectively. Results showed that volatile components in F. velutipes significantly changed during hot air drying according to the principal component analysis and radar fingerprint chart of electronic nose. Volatile compounds of fresh F. velutipes consisted mainly of ketones, aldehydes and alcohols, and 3-octanone was the dominant compound. Drying process could significantly decrease the relative content of ketones and promoted the generation of alcohols, acids, and esters, which became the main volatile compounds of dried F. velutipes. These may provide a theoretical basis for the formation mechanism of flavor substances in dried F. velutipes. Copyright © 2015 Elsevier Ltd. All rights reserved.

Effects of four different drying methods on the carotenoid composition and antioxidant capacity of dried Gac peel.

PubMed

Chuyen, Hoang V; Roach, Paul D; Golding, John B; Parks, Sophie E; Nguyen, Minh H

2017-03-01

Gac fruit (Momordica cochinchinensis Spreng.) is a rich source of carotenoids for the manufacture of powder, oil and capsules for food, cosmetic and pharmaceutical uses. Currently, only the aril of the Gac fruit is processed and the peel, similar to the other components, is discarded, although it contains high level of carotenoids, which could be extracted for commercial use. In the present study, four different drying methods (hot-air, vacuum, heat pump and freeze drying), different temperatures and drying times were investigated for producing dried Gac peel suitable for carotenoid extraction. The drying methods and drying temperatures significantly affected the drying time, carotenoid content and antioxidant capacity of the dried Gac peel. Among the investigated drying methods, hot-air drying at 80  o C and vacuum drying at 50  o C produced dried Gac peel that exhibited the highest retention of carotenoids and the strongest antioxidant capacity. Hot-air drying at 80  o C and vacuum drying at 50  o C are recommended for the drying of Gac peel. © 2016 Society of Chemical Industry. © 2016 Society of Chemical Industry.

Extracting Vegetation Coverage in Dry-hot Valley Regions Based on Alternating Angle Minimum Algorithm

NASA Astrophysics Data System (ADS)

Y Yang, M.; Wang, J.; Zhang, Q.

2017-07-01

Vegetation coverage is one of the most important indicators for ecological environment change, and is also an effective index for the assessment of land degradation and desertification. The dry-hot valley regions have sparse surface vegetation, and the spectral information about the vegetation in such regions usually has a weak representation in remote sensing, so there are considerable limitations for applying the commonly-used vegetation index method to calculate the vegetation coverage in the dry-hot valley regions. Therefore, in this paper, Alternating Angle Minimum (AAM) algorithm of deterministic model is adopted for selective endmember for pixel unmixing of MODIS image in order to extract the vegetation coverage, and accuracy test is carried out by the use of the Landsat TM image over the same period. As shown by the results, in the dry-hot valley regions with sparse vegetation, AAM model has a high unmixing accuracy, and the extracted vegetation coverage is close to the actual situation, so it is promising to apply the AAM model to the extraction of vegetation coverage in the dry-hot valley regions.

Effects of Cold-Dry (Harmattan) and Hot-Dry Seasons on Daily Rhythms of Rectal and Body Surface Temperatures in Sheep and Goats in a Natural Tropical Environment

PubMed Central

Ayo, Joseph O.

2016-01-01

Studies on daily rhythmicity in livestock under natural conditions are limited, and there is mounting evidence that rhythm patterns differ between chronobiological studies conducted in the laboratory and studies conducted under pronounced natural seasonality. Here, we investigated the influence of cold-dry (harmattan) and hot-dry seasons on daily rhythmicity of rectal (RT) and body surface temperatures (BST) in indigenous sheep and goats under natural light-dark cycles. The RT and BST of the animals, and the ambient temperature (AT) and relative humidity (RH) inside the pen, were measured every three hours for a period of two days, twice on separate days during the hot-dry and the harmattan seasons, respectively. The AT and RH had minimum values of 16°C and 15% recorded during the harmattan and maximum values of 32°C and 46% recorded during the hot-dry season, respectively. A trigonometric statistical model was applied to characterize the main rhythmic parameters according to the single cosinor procedure. The result showed that RT and BST exhibited different degrees of daily rhythmicity, and their oscillatory patterns differed with the seasons (larger amplitude during the harmattan season than during the hot-dry season). The goats displayed greater (p < 0.05) amplitude of BST than the sheep in all seasons. The acrophases were restricted to the light phase of the light-dark cycle. The mesor of RT in goats was not affected by the season, but mesors of BST in both species were significantly higher (p < 0.05) during the hot-dry than the harmattan season. The goats had a more robust RT rhythm (70%) as compared to the sheep (56%). Overall, the results demonstrated that seasonal changes influenced considerably the daily rhythmicity of RT and BST in sheep and goats under natural light-dark cycle. Awareness of these changes may be useful in the improvement of diagnosis, treatment and prevention of diseases, and welfare and productivity of sheep and goats under cold-dry and hot-dry conditions.

Synthesis of descriptive sensory attributes and hedonic rankings of dried persimmon (Diospyros kaki sp.)

USDA-ARS?s Scientific Manuscript database

This work aimed to characterize the sensory attributes of hot air-dried persimmon (Diospyros kaki) chips, correlate these attributes with consumer hedonic information, and, by doing so, present recommendations for cultivars that are most suitable for hot-air drying. A trained sensory panel evaluated...

Utilization potential evaluation of plant resources in the dry-hot valley of Jinsha River

NASA Astrophysics Data System (ADS)

Xi, Rong; Xu, Naizhong; Liu, Shengxiang; Ren, Tingyan

2017-08-01

Plant resources in the dry-hot valley of Jinsha River are endemic to a class of district. The article adopts the analytic hierarchy process method to evaluate the exploitation and utilization potential of plant resources of thirty typical plant resources on the basis of their characteristics in the dry-hot valley of Jinsha River, which provide scientific evidence for quantitative evaluation of regional plant resources, and we also suggest pathways offering protection and development.

46 CFR 148.250 - Direct reduced iron (DRI); hot-molded briquettes.

Code of Federal Regulations, 2011 CFR

2011-10-01

... concentration of fines (pieces less than 6.35mm in size) in any one location in the cargo hold. (f) Adequate... hot-molded briquettes. (h) Radar and RDF scanners must be adequately protected against dust generated during cargo transfer operations of DRI hot-molded briquettes. (i) During final discharge only, a fine...

46 CFR 148.250 - Direct reduced iron (DRI); hot-molded briquettes.

Code of Federal Regulations, 2012 CFR

2012-10-01

... concentration of fines (pieces less than 6.35mm in size) in any one location in the cargo hold. (f) Adequate... hot-molded briquettes. (h) Radar and RDF scanners must be adequately protected against dust generated during cargo transfer operations of DRI hot-molded briquettes. (i) During final discharge only, a fine...

46 CFR 148.250 - Direct reduced iron (DRI); hot-molded briquettes.

Code of Federal Regulations, 2014 CFR

2014-10-01

... concentration of fines (pieces less than 6.35mm in size) in any one location in the cargo hold. (f) Adequate... hot-molded briquettes. (h) Radar and RDF scanners must be adequately protected against dust generated during cargo transfer operations of DRI hot-molded briquettes. (i) During final discharge only, a fine...

46 CFR 148.250 - Direct reduced iron (DRI); hot-molded briquettes.

Code of Federal Regulations, 2013 CFR

2013-10-01

... concentration of fines (pieces less than 6.35mm in size) in any one location in the cargo hold. (f) Adequate... hot-molded briquettes. (h) Radar and RDF scanners must be adequately protected against dust generated during cargo transfer operations of DRI hot-molded briquettes. (i) During final discharge only, a fine...

Chromatic Dimensions Earthy, Watery, Airy, and Fiery.

PubMed

Albertazzi, Liliana; Koenderink, Jan J; van Doorn, Andrea

2015-01-01

In our study, for a small number of antonyms, we investigate whether they are cross-modally or ideaesthetically related to the space of colors. We analyze the affinities of seven antonyms (cold-hot, dull-radiant, dead-vivid, soft-hard, transparent-chalky, dry-wet, and acid-treacly) and their intermediate connotations (cool-warm, matt-shiny, numb-lively, mellow-firm, semi-transparent-opaque, semi-dry-moist, and sour-sweet) as a function of color. We find that some antonyms relate to chromatic dimensions, others to achromatic ones. The cold-hot antonym proves to be the most salient dimension. The dry-wet dimension coincides with the cold-hot dimension, with dry corresponding to hot and wet to cold. The acid-treacly dimension proves to be transversal to the cold-hot dimension; hence, the pairs mutually span the chromatic domain. The cold-hot and acid-treacly antonyms perhaps recall Hering's opponent color system. The dull-radiant, transparent-chalky, and dead-vivid pairs depend little upon chromaticity. Of all seven antonyms, only the soft-hard one turns out to be independent of the chromatic structure. © The Author(s) 2015.

Comparison between hot-melt extrusion and spray-drying for manufacturing solid dispersions of the graft copolymer of ethylene glycol and vinylalcohol.

PubMed

Guns, Sandra; Dereymaker, Aswin; Kayaert, Pieterjan; Mathot, Vincent; Martens, Johan A; Van den Mooter, Guy

2011-03-01

To investigate the effect of the manufacturing method (spray-drying or hot-melt extrusion) on the kinetic miscibility of miconazole and the graft copolymer poly(ethyleneglycol-g-vinylalcohol). The effect of heat pre-treatment of solutions used for spray-drying and the use of spray-dried copolymer as excipient for hot-melt extrusion was investigated. The solid dispersions were prepared at different drug-polymer ratios and analyzed with modulated differential scanning calorimetry and X-ray powder diffraction. Miconazole either mixed with the PEG-fraction of the copolymer or crystallized in the same or a different polymorph as the starting material. The kinetic miscibility was higher for the solid dispersions obtained from solutions which were pre-heated compared to those spray-dried from solutions at ambient temperature. Hot-melt extrusion resulted in an even higher mixing capability. Here the use of the spray-dried copolymer did not show any benefit concerning the kinetic miscibility of the drug and copolymer, but it resulted in a remarkable decrease in the torque experienced by the extruder allowing extrusion at lower temperature and torque. The manufacturing method has an influence on the mixing capacity and phase behavior of solid dispersions. Heat pre-treatment of the solutions before spray-drying can result in a higher kinetic miscibility. Amorphization of the copolymer by spray-drying before using it as an excipient for hot-melt extrusion can be a manufacturing benefit.

Effect of hot-dry environment on fiber-reinforced self-compacting concrete

NASA Astrophysics Data System (ADS)

Tioua, Tahar; Kriker, Abdelouahed; Salhi, Aimad; Barluenga, Gonzalo

2016-07-01

Drying shrinkage can be a major reason for the deterioration of concrete structures. Variation in ambient temperature and relative humidity cause changes in the properties of hardened concrete which can affect their mechanical and drying shrinkage characteristics. The present study investigated mechanical strength and particularly drying shrinkage properties of self-compacting concretes (SCC) reinforced with date palm fiber exposed to hot and dry environment. In this study a total of nine different fibers reinforced self compacting concrete (FRSCC) mixtures and one mixture without fiber were prepared. The volume fraction and the length of fibers reinforcement were 0.1-0.2-0.3% and 10-20-30 mm. It was observed that drying shrinkage lessened with adding low volumetric fraction and short length of fibers in curing condition (T = 20 °C and RH = 50 ± 5 %), but increased in hot and dry environment.

Hot dry rock geothermal energy: status of exploration and assessment. Report No. 1 of the hot dry rock assessment panel

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1977-06-01

The status of knowledge of attempts to utilize hot dry rock (HDR) geothermal energy is summarized. It contains (1) descriptions or case histories of the ERDA-funded projects at Marysville, MT, Fenton Hill, NM, and Coso Hot Springs, CA; (2) a review of the status of existing techniques available for exploration and delineation of HDR; (3) descriptions of other potential HDR sites; (4) definitions of the probable types of HDR resource localities; and (5) an estimate of the magnitude of the HDR resource base in the conterminous United States. The scope is limited to that part of HDR resource assessment relatedmore » to the determination of the extent and character of HDR, with emphasis on the igneous-related type. It is estimated that approximately 74 Q (1 Q = 1,000 Quads) of heat is stored in these sites within the conterminous U.S. at depths less than 10 km and temperatures above 150/sup 0/C, the minimum for power generation. (Q = 10/sup 18/ BTU = 10/sup 21/J; the total U.S. consumption for 1972 was approximately 0.07 Q). Approximately 6300 Q are stored in the conduction-dominated parts of the crust in the western U.S. (23% of the total surface area), again at depths less than 10 km and temperatures above 150/sup 0/C. Nearly 10,000 Q are believed to be contained in crustal rocks underlying the entire conterminous U.S., at temperatures above 150/sup 0/C. The resource base is significantly larger for lower grade heat. (JGB)« less

The effect of seasons on behaviour during milking in buffaloes ( Bos bubalis)

NASA Astrophysics Data System (ADS)

Gangwar, P. C.

1982-06-01

An investigation on behaviour during milking involving 200 buffaloes was carried out to study the effect of climate on milking behaviour for a period of four years. The results obtained were: (1) In extremely docile animals (temperament score I) the mean distribution was least (33.5) in hot-dry summer as compared to winter (39.2) and hot-humid summer. (2) The number of buffaloes milked after oxytocin injections was maximum (11.1%) during the hot-dry summer against other seasons for the temperament score I over temperament scores III and IV, where all buffaloes were milked with oxytocin injections. (3) The mean flow rate was least in hot-dry summer in each temperament score. (4) Milking time was higher in all the temperament scored buffaloes during the hot-dry summer than during the other seasons. It is concluded that as environmental temperature increases, there occurs an increase in thermal stress, the milking behaviour changes and animals become more hostile and excited which leads to a decrease in milk production.

Daidzein-rich isoflavone aglycones are potentially effective in reducing hot flashes in menopausal women.

PubMed

Khaodhiar, Lalita; Ricciotti, Hope A; Li, Linglin; Pan, Weijun; Schickel, Mary; Zhou, Jinrong; Blackburn, George L

2008-01-01

The aim of this study was to determine the effect of DRIs on hot flash symptoms in menopausal women. This was a randomized, double-blind, placebo-controlled trial of menopausal women, aged 38 to 60 years, who experienced 4 to 14 hot flashes per day. After a 1-week run-in period, a total of 190 menopausal women were randomized to receive a placebo or 40 or 60 mg/day of a DRI for 12 weeks. The primary outcome was the mean changes from baseline to week 12 in the frequency of hot flashes recorded in the participant diary. The secondary outcomes included changes in quality of life and hormonal profiles. A total of 147 women (77%) completed the study. It was found that 40 and 60 mg of DRI improved hot flash frequency and severity equally. At 8 weeks hot flash frequency was reduced by 43% in the 40-mg DRI group and by 41% in the 60-mg DRI group, compared with 32% in the placebo group (P = not significant vs placebo). The corresponding numbers for 12 weeks were 52%, 51%, and 39%, respectively (P = 0.07 and 0.09 vs placebo). When comparing the two treatment groups with the placebo group, there were significant reductions in mean daily hot flash frequency. The supplement (either 40 or 60 mg) reduced hot flash frequency by 43% at 8 weeks (P = 0.1) and 52% at 12 weeks (P = 0.048) but did not cause any significant changes in endogenous sex hormones or thyroid hormones. Menopausal quality of life improved in all three groups, although there were no statistically significant differences between groups. DRI supplementation may be an effective and acceptable alternative to hormone treatment for menopausal hot flashes.

[Characteristics of floor litter and soil arthropod community in different types ot subtropical forest in Ailao Mountain of Yunnan, Southwest China].

PubMed

Yang, Zhao; Yang, Xiao-Dong

2011-11-01

By using line transect method, an investigation was conducted on the floor litter and soil arthropod community in a mid mountain wet evergreen broad-leaved forest, a mossy dwarf forest, and a Populus bonatii forest in Ailao Mountain of Yunnan in April (dry and hot season), June (rainy season), and December (dry and cold season), 2005. In both dry and rainy seasons, the existing floor litter mass, C storage, and C/N ratio in the three forests all increased in the order of mossy dwarf forest > P. bonatii forest > evergreen broad-leaved forest, but the N storage had less difference. In the floor litter layer of the forests, Acari and Collembola were the dominant groups of soil arthropod community, while Diptera larvae, Coleoptera, ants, and Homoptera were the common groups. The Sorenson coefficients of soil arthropod community in the three forests were extremely great. No significant differences were observed in the soil arthropod density (ind x m(-2)) in the floor litter layer among the three forests, but the relative density (ind x g(-1)) of soil arthropods was higher in the evergreen broad-leaved forest and P. bonatii forest than in the mossy dwarf forest. In the three forests, the density of soil arthropods was significantly higher in dry season than in rainy season, but the Shannon diversity index had less difference. There were significant positive correlations between the existing floor litter mass and the individual density (ind x m(-2)) and dominant groups of soil arthropod communities in dry and hot season (April), but negative correlations between the existing floor litter mass and the relative density (ind x g(-1)) of soil arthropod communities and Acari in dry and cold season (December). The individual densities of Collembola and Coleoptera also had positive correlations with the N storage of the existing floor litter mass in the three forests. It was considered that the floor litter and the development of soil arthropod community in the litter layer of the subtropical forests in Ailao Mountain had a close relation with the vegetation structure of the forests, and the individual density and the diversity of the soil arthropod community were controlled by the floor litter, whereas the environmental factors such as temperature and moisture in the forests also had obvious effects on the seasonal dynamics of the individual density of the soil arthropods.

Drying of Pigment-Cellulose Nanofibril Substrates

PubMed Central

Timofeev, Oleg; Torvinen, Katariina; Sievänen, Jenni; Kaljunen, Timo; Kouko, Jarmo; Ketoja, Jukka A.

2014-01-01

A new substrate containing cellulose nanofibrils and inorganic pigment particles has been developed for printed electronics applications. The studied composite structure contains 80% fillers and is mechanically stable and flexible. Before drying, the solids content can be as low as 20% due to the high water binding capacity of the cellulose nanofibrils. We have studied several drying methods and their effects on the substrate properties. The aim is to achieve a tight, smooth surface keeping the drying efficiency simultaneously at a high level. The methods studied include: (1) drying on a hot metal surface; (2) air impingement drying; and (3) hot pressing. Somewhat surprisingly, drying rates measured for the pigment-cellulose nanofibril substrates were quite similar to those for the reference board sheets. Very high dewatering rates were observed for the hot pressing at high moisture contents. The drying method had significant effects on the final substrate properties, especially on short-range surface smoothness. The best smoothness was obtained with a combination of impingement and contact drying. The mechanical properties of the sheets were also affected by the drying method and associated temperature. PMID:28788220

Phlogopite Decomposition, Water, and Venus

NASA Technical Reports Server (NTRS)

Johnson, N. M.; Fegley, B., Jr.

2005-01-01

Venus is a hot and dry planet with a surface temperature of 660 to 740 K and 30 parts per million by volume (ppmv) water vapor in its lower atmosphere. In contrast Earth has an average surface temperature of 288 K and 1-4% water vapor in its troposphere. The hot and dry conditions on Venus led many to speculate that hydrous minerals on the surface of Venus would not be there today even though they might have formed in a potentially wetter past. Thermodynamic calculations predict that many hydrous minerals are unstable under current Venusian conditions. Thermodynamics predicts whether a particular mineral is stable or not, but we need experimental data on the decomposition rate of hydrous minerals to determine if they survive on Venus today. Previously, we determined the decomposition rate of the amphibole tremolite, and found that it could exist for billions of years at current surface conditions. Here, we present our initial results on the decomposition of phlogopite mica, another common hydrous mineral on Earth.

Isolation and Characterization of Microsatellite Loci for Hibiscus aridicola (Malvaceae), an Endangered Plant Endemic to the Dry-Hot Valleys of Jinsha River in Southwest China

PubMed Central

Zhang, Le; Sun, Weibang; Wang, Zhonglang; Guan, Kaiyun; Yang, Junbo

2011-01-01

Hibiscus aridicola (Malvaceae) is an endangered ornamental shrub endemic to the dry-hot valleys of Jinsha River in southwest China. Only four natural populations of H. aridicola exist in the wild according to our field investigation. It can be inferred that H. aridicola is facing a very high risk of extinction in the wild and an urgent conservation strategy is required. By using a modified biotin-streptavidin capture method, a total of 40 microsatellite markers were developed and characterized in H. aridicola for the first time. Polymorphisms were evaluated in 39 individuals from four natural populations. Fifteen of the markers showed polymorphisms with two to six alleles per locus; the observed heterozygosity ranged from 0.19 to 0.72. These microsatellite loci would be useful tools for population genetics studies on H. aridicola and other con-generic species which are important to the conservation and development of endangered species. PMID:22016620

Technology Solutions Case Study: High-Performance Ducts in Hot-Dry Climates

DOE Office of Scientific and Technical Information (OSTI.GOV)

M. Hoeschele, A. German, E. Weitzel, R. Chitwood

2015-08-01

Ducts in conditioned space (DCS) represent a high priority measure for moving the next generation of new homes to the Zero Net Energy performance level. Various strategies exist for incorporating ducts within the conditioned thermal envelope. To support this activity, in 2013 the Pacific Gas & Electric Company initiated a project with Davis Energy Group (lead for the Building America team, Alliance for Residential Building Innovation) to solicit builder involvement in California to participate in field demonstrations of various DCS strategies. Builders were given incentives and design support in exchange for providing site access for construction observation, diagnostic testing, andmore » builder survey feedback. Information from the project was designed to feed into California's 2016 Title 24 process, but also to serve as an initial mechanism to engage builders in more high performance construction strategies. This Building America project complemented information collected in the California project with BEopt simulations of DCS performance in hot/dry climate regions.« less

Using Flory-Huggins phase diagrams as a pre-formulation tool for the production of amorphous solid dispersions: a comparison between hot-melt extrusion and spray drying.

PubMed

Tian, Yiwei; Caron, Vincent; Jones, David S; Healy, Anne-Marie; Andrews, Gavin P

2014-02-01

Amorphous drug forms provide a useful method of enhancing the dissolution performance of poorly water-soluble drugs; however, they are inherently unstable. In this article, we have used Flory-Huggins theory to predict drug solubility and miscibility in polymer candidates, and used this information to compare spray drying and melt extrusion as processes to manufacture solid dispersions. Solid dispersions were prepared using two different techniques (hot-melt extrusion and spray drying), and characterised using a combination of thermal (thermogravimetric analysis and differential scanning calorimetry), spectroscopic (Fourier transform infrared spectroscopy (FTIR) and X-ray diffraction methods. Spray drying permitted generation of amorphous solid dispersions across a wider drug concentration than melt extrusion. Melt extrusion provided sufficient energy for more intimate mixing to be achieved between drug and polymer, which may improve physical stability. It was also confirmed that stronger drug-polymer interactions might be generated through melt extrusion. Remixing and dissolution of recrystallised felodipine into the polymeric matrices did occur during the modulated differential scanning calorimetry analysis, but the complementary information provided from FTIR confirms that all freshly prepared spray-dried samples were amorphous with the existence of amorphous drug domains within high drug-loaded samples. Using temperature-composition phase diagrams to probe the relevance of temperature and drug composition in specific polymer candidates facilitates polymer screening for the purpose of formulating solid dispersions. © 2013 Royal Pharmaceutical Society.

Critical heat flux maxima during boiling crisis on textured surfaces

PubMed Central

Dhillon, Navdeep Singh; Buongiorno, Jacopo; Varanasi, Kripa K.

2015-01-01

Enhancing the critical heat flux (CHF) of industrial boilers by surface texturing can lead to substantial energy savings and global reduction in greenhouse gas emissions, but fundamentally this phenomenon is not well understood. Prior studies on boiling crisis indicate that CHF monotonically increases with increasing texture density. Here we report on the existence of maxima in CHF enhancement at intermediate texture density using measurements on parametrically designed plain and nano-textured micropillar surfaces. Using high-speed optical and infrared imaging, we study the dynamics of dry spot heating and rewetting phenomena and reveal that the dry spot heating timescale is of the same order as that of the gravity and liquid imbibition-induced dry spot rewetting timescale. Based on these insights, we develop a coupled thermal-hydraulic model that relates CHF enhancement to rewetting of a hot dry spot on the boiling surface, thereby revealing the mechanism governing the hitherto unknown CHF enhancement maxima. PMID:26346098

Inhibition of Listeria monocytogenes in Hot Dogs by Surface Application of Freeze-Dried Bacteriocin-Containing Powders from Lactic Acid Bacteria.

PubMed

Ünlü, Gülhan; Nielsen, Barbara; Ionita, Claudia

2016-06-01

Six lactic acid bacteria (LAB) strains, Lactococcus lactis BFE 920, L. lactis subsp. lactis ATCC 11454, L. lactis subsp. cremoris ATCC 14365, Lactobacillus curvatus L442, Lact. curvatus LTH 1174, and Lact. bavaricus MN, were grown in cheddar cheese whey supplemented with complex nutrient sources. Cell-free culture supernatants were freeze-dried, and the resulting bacteriocin-containing powders were applied on the surface of hot dogs that were inoculated (~4 log cfu/hot dog) with a five-strain Listeria monocytogenes cocktail. Hot dogs were vacuum-sealed and stored at 4 °C for 4 weeks. L. monocytogenes was enumerated, using both tryptic soy agar (TSA) and oxford listeria agar (OXA), on day 0 and at 1, 2, 3, and 4 weeks of the refrigerated storage. In hot dogs containing only the L. monocytogenes inoculum, L. monocytogenes counts increased from 4 up to 7 log cfu/hot dog. All samples containing freeze-dried bacteriocin-containing powders exhibited significantly lowered (P < 0.05) L. monocytogenes populations on the surface of hot dogs throughout the 4-week study except for bavaricin MN powder. Bacterial counts on hot dogs packed without any powder were statistically equal on day 0 when enumerated on OXA. Freeze-dried bacteriocin-containing powders from Lact. curvatus L442 and L. lactis subsp. cremoris ATCC 14365 decreased L. monocytogenes populations on the surface of hot dogs by greater than 2 log cfu/hot dog throughout the 4-week study. For the powdered bacteriocin preparations from L. lactis BFE 920, L. lactis subsp. lactis ATCC 11454, and Lact. curvatus LTH 1174, L. monocytogenes populations were determined to be approximately 3-log cfu/hot dog after 4 weeks of storage.

Effect of hot-boned pork on the keeping quality of fresh pork sausage.

PubMed

Guerrero Legarreta, I; Usborne, W R; Ashton, G C

1987-01-01

The first experiment evaluated the effect of solid carbon dioxide (dry ice) addition to hot-boned meat, in different proportions, upon the keeping quality of fresh pork sausage patties. Dry ice had some negative effects at levels of 20% to 40%, such as hardening and colour fading of samples, although it increased water-holding capacity of the sausage. In the second experiment three proportions of hot-boned meat and chilled meat were evaluated as a means to extend the retail storage time of fresh pork sausage links. Hot-boned pork was treated by three methods: freezing the meat before grinding, salting and freezing, and salting plus dry ice addition. The results favoured the use of 50% hot-boned meat and 50% chilled meat, for which the lowest hardness and oxidation values were obtained. Microbial counts and hue values showed no significant variation among the three treatments. Salting and freezing hot-boned meat before grinding was the method which produced the best overall quality. Copyright © 1987. Published by Elsevier Ltd.

The economical utilization of geothermal energy

NASA Astrophysics Data System (ADS)

Rose, G.

1982-12-01

The geothermal energy which is stored in hot dry rock could be theoretically utilized for the generation of power. The hot-dry-rock procedure can provide a flow of hot water. The considered binary system can transform the obtained thermal energy into electrical energy. The system makes use of a Rankine cycle with a working fluid having a low boiling point. Heat from the hot water is transferred to the working fluid. The present investigation is concerned with the development of a method for the calculation of the entire process. The results obtained with the computational method are to provide a basis for the determination of the operational characteristics. The development method is used for the study of a process based on the use of carbon dioxide as working fluid. The economics of a use of the hot-dry-rock process with the binary system is also investigated. It is found that the considered procedure is not economical. Economical operation requires, in particular, hot water supplied at a much lower cost.

Influence of drying method on steviol glycosides and antioxidants in Stevia rebaudiana leaves.

PubMed

Periche, Angela; Castelló, María Luisa; Heredia, Ana; Escriche, Isabel

2015-04-01

The application of different drying conditions (hot air drying at 100 °C and 180 °C, freeze drying and shade drying) on steviol glycosides (stevioside, dulcoside A, rebaudioside A and rebaudioside C) and antioxidants in Stevia leaves was evaluated. Stevioside, the major glycoside found in fresh leaves (81.2mg/g), suffered an important reduction in all cases, although shade drying was the least aggressive treatment. Considering the antioxidant parameters (total phenols, flavonoids and total antioxidants), the most suitable drying method was hot air at 180 °C, since it substantially increased all of them (76.8 mg gallic acid, 45.1mg catechin and 126 mg Trolox, all equivalent/g Stevia, respectively), with respect to those present in fresh leaves (44.4, 2.5 and 52.9 mg equivalent/g). Therefore, the ideal method for drying Stevia leaves depends on their final use (sweetener or antioxidant), although, hot air at 180 °C is the most recommendable if only one treatment has to be chosen. Copyright © 2014 Elsevier Ltd. All rights reserved.

Effect of Steam Blanching and Drying on Phenolic Compounds of Litchi Pericarp.

PubMed

Kessy, Honest N E; Hu, Zhuoyan; Zhao, Lei; Zhou, Molin

2016-06-03

The effects of different treatment methods on the stability and antioxidant capacity of the bioactive phenolic compounds of litchi pericarps were investigated. Fresh litchi pericarps were open air-dried, steam-blanched for 3 min in combination with hot air oven drying at 60 and 80 °C, and unblanched pericarps were dried in a hot air oven at 40, 60, 70 and 80 °C until equilibrium weight was reached. The total phenolic compounds, flavonoids, anthocyanins, proanthocyanidins and individual procyanidins, and antioxidant activity were analyzed. The combination of blanching and drying at 60 °C significantly (p < 0.05) improved the release of phenolic compounds, individual procyanidins, and the extracts' antioxidant capacity compared with the unblanched hot air oven-dried and open air-dried pericarps. Drying of fresh unblanched litchi pericarps in either open air or a hot air oven caused significant losses (p < 0.05) in phenolic compounds and individual procyanidins, leading to a reduction in the antioxidant activity. A similar increase, retention or reduction was reflected in flavonoids, proanthocyanidins and anthocyanins because they are sub-groups of phenolic compounds. Ferric reducing antioxidant power (FRAP) and 1,1-diphenyl-2-picryldydrazyl (DPPH) radical-scavenging capacity of the treated pericarps were significantly correlated (r ≥ 0.927, p < 0.01) with the total phenolic compounds. Thus, the combination of steam blanching and drying treatments of fresh litchi pericarps could produce a stable and dry litchi pericarp that maintains phenolic compounds and antioxidant capacity as a raw material for further recovery of the phytochemicals.

Generation of Hot Water from Hot-Dry for Heavy-Oil Recovery in Northern Alberta, Canada

NASA Astrophysics Data System (ADS)

Pathak, V.; Babadagli, T.; Majorowicz, J. A.; Unsworth, M. J.

2011-12-01

The focus of prior applications of hot-dry-rock (HDR) technology was mostly aimed at generating electricity. In northern Alberta, the thermal gradient is low and, therefore, this technology is not suitable for electricity generation. On the other hand, the cost of steam and hot water, and environmental impacts, are becoming critical issues in heavy-oil and bitumen recovery in Alberta. Surface generation of steam or hot-water accounts for six percent of Canada's natural gas consumption and about 50 million tons of CO2 emission. Lowered cost and environmental impacts are critical in the widespread use of steam (for in-situ recovery) and hot-water (for surface extraction of bitumen) in this region. This paper provides an extensive analysis of hot-water generation to be used in heavy-oil/bitumen recovery. We tested different modeling approaches used to determine the amount of energy produced during HDR by history matching to example field data. The most suitable numerical and analytical models were used to apply the data obtained from different regions containing heavy-oil/bitumen deposits in northern Alberta. The heat generation capacity of different regions was determined and the use of this energy (in the form of hot-water) for surface extraction processes was evaluated. Original temperature gradients were applied as well as realistic basement formation characteristics through an extensive hydro thermal analysis in the region including an experimental well drilled to the depth of 2,500m. Existing natural fractures and possible hydraulic fracturing scenarios were evaluated from the heat generation capacity and the economics points of view. The main problem was modeling difficulties, especially determination and representation of fracture network characteristics. A sensitivity analysis was performed for the selected high temperature gradient regions in Alberta. In this practice, the characteristics of hydraulic fractures, injection rate, depth, the distance between injection and production wells and formation thickness were used as variables and an optimization study was carried out based on these variables. The results showed that the hot water (50 C at surface) needed in Fort McMurray for extraction could be obtained at lower costs than the generation of it using natural gas.

Do older adults experience greater thermal strain during heat waves?

PubMed

Stapleton, Jill M; Larose, Joanie; Simpson, Christina; Flouris, Andreas D; Sigal, Ronald J; Kenny, Glen P

2014-03-01

Heat waves are the cause of many preventable deaths around the world, especially among older adults and in countries with more temperate climates. In the present study, we examined the effects of age on whole-body heat loss and heat storage during passive exposure to environmental conditions representative of the upper temperature extremes experienced in Canada. Direct and indirect calorimetry measured whole-body evaporative heat loss and dry heat exchange, as well as the change in body heat content. Twelve younger (21 ± 3 years) and 12 older (65 ± 5 years) adults with similar body weight (younger: 72.0 ± 4.4 kg; older: 80.1 ± 4.2 kg) and body surface area (younger: 1.8 ± 0.1 m(2); older: 2.0 ± 0.1 m(2)) rested for 2 h in a hot-dry [36.5 °C, 20% relative humidity (RH)] or hot-humid (36.5 °C, 60% RH) environment. In both conditions, evaporative heat loss was not significantly different between groups (dry: p = 0.758; humid: p = 0.814). However, the rate of dry heat gain was significantly greater (by approx. 10 W) for older adults relative to younger adults during the hot-dry (p = 0.032) and hot-humid exposure (p = 0.019). Consequently, the cumulative change in body heat content after 2 h of rest was significantly greater in older adults in the hot-dry (older: 212 ± 25 kJ; younger: 131 ± 27 kJ, p = 0.018) as well as the hot-humid condition (older: 426 ± 37 kJ; younger: 317 ± 45 kJ, p = 0.037). These findings demonstrate that older individuals store more heat during short exposures to dry and humid heat, suggesting that they may experience increased levels of thermal strain in such conditions than people of younger age.

Drying characteristics of whole Musa AA group ‘Kluai Leb Mu Nang’ using hot air and infrared vacuum

NASA Astrophysics Data System (ADS)

Kulketwong, C.; Thungsotanon, D.; Suwanpayak, N.

2017-06-01

Dried Musa AA group ‘Kluai Leb Mu Nang’ are the famous processing goods of Chumphon province, the south of Thailand. In this paper, we improved the qualities of whole Musa AA group ‘Kluai leb Mu Nang’ by using the hot air and infrared vacuum (HA and infrared vacuum) drying method which has two stages. The first stage of the method is the hot air (HA) and hot air-infrared (HAI) drying for rapidly reducing the moisture content and the drying times at atmospheric pressure, and the second stage, the moisture content, and color of the samples can be controlled by the HA and infrared vacuum drying. The experiment was evaluated by the terms of firmness, color change, moisture content, vacuum pressure and energy consumption at various temperatures. The results were found that the suitable temperature of the HAI and HA and infrared vacuum drying stages at 70°C and 55°C, respectively, while the suitable vacuum pressure in the second process was -0.4 bar. The samples were dried in a total of 28 hrs using 13.83 MJ/kg of specific energy consumption (stage 1 with 8.8 MJ/kg and stage 2 of 5.03 MJ/kg). The physical characteristics of the 21% (wb) of dried bananas can be measured the color change, L*=38.56, a*=16.47 and b*=16.3, was approximate the goods from the local market, whereas the firmness of them was more tender and shown a value of 849.56 kN/m3.

Performance of a convective, infrared and combined infrared- convective heated conveyor-belt dryer.

PubMed

El-Mesery, Hany S; Mwithiga, Gikuru

2015-05-01

A conveyor-belt dryer was developed using a combined infrared and hot air heating system that can be used in the drying of fruits and vegetables. The drying system having two chambers was fitted with infrared radiation heaters and through-flow hot air was provided from a convective heating system. The system was designed to operate under either infrared radiation and cold air (IR-CA) settings of 2000 W/m(2) with forced ambient air at 30 °C and air flow of 0.6 m/s or combined infrared and hot air convection (IR-HA) dryer setting with infrared intensity set at 2000 W/m(2) and hot at 60 °C being blown through the dryer at a velocity of 0.6 m/s or hot air convection (HA) at an air temperature of 60 °C and air flow velocity 0.6 m/s but without infrared heating. Apple slices dried under the different dryer settings were evaluated for quality and energy requirements. It was found that drying of apple (Golden Delicious) slices took place in the falling rate drying period and no constant rate period of drying was observed under any of the test conditions. The IR-HA setting was 57.5 and 39.1 % faster than IR-CA and HA setting, respectively. Specific energy consumption was lower and thermal efficiency was higher for the IR-HA setting when compared to both IR-CA and HA settings. The rehydration ratio, shrinkage and colour properties of apples dried under IR-HA conditions were better than for either IR-CA or HA.

A comparative study between hot-melt extrusion and spray-drying for the manufacture of anti-hypertension compatible monolithic fixed-dose combination products.

PubMed

Kelleher, J F; Gilvary, G C; Madi, A M; Jones, D S; Li, S; Tian, Y; Almajaan, A; Senta-Loys, Z; Andrews, G P; Healy, A M

2018-07-10

The purpose of this work was to investigate the application of different advanced continuous processing techniques (hot melt extrusion and spray drying) to the production of fixed-dose combination (FDC) monolithic systems comprising of hydrochlorothiazide and ramipril for the treatment of hypertension. Identical FDC formulations were manufactured by the two different methods and were characterised using powder X-ray diffraction (PXRD) and modulated differential scanning calorimetry (mDSC). Drug dissolution rates were investigated using a Wood's apparatus, while physical stability was assessed on storage under controlled temperature and humidity conditions. Interestingly both drugs were transformed into their amorphous forms when spray dried, however, hydrochlorothiazide was determined, by PXRD, to be partially crystalline when hot melt extruded with either polymer carrier (Kollidon® VA 64 or Soluplus®). Hot melt extrusion was found to result in significant degradation of ramipril, however, this could be mitigated by the inclusion of the plasticizer, polyethylene glycol 3350, in the formulation and appropriate adjustment of processing temperature. The results of intrinsic dissolution rate studies showed that hot-melt extruded samples were found to release both drugs faster than identical formulations produced via spray drying. However, the differences were attributable to the surface roughness of the compressed discs in the Wood's apparatus, rather than solid state differences between samples. After a 60-day stability study spray dried samples exhibited a greater physical stability than the equivalent hot melt extruded samples. Copyright © 2018 Elsevier B.V. All rights reserved.

Ecotoxicology for risk assessment in arid zones: some key issues.

PubMed

Everts, J W

1997-01-01

In the hot arid zones of the world, ecotoxicological research is in statu nascendi. In these zones, the major sources of contamination by toxicants are: (1) plant protection and vector control in wet zones; (2) large-scale crop protection campaigns in dry and ephemeral wet zones; (3) refuse and obsolete pesticides in dry zones; and (4) mining. Economic development in many of these zones requires an adequate knowledge of certain basic principles, i.e., where extrapolating existing knowledge does not apply. The vulnerability of ecosystems to contaminants is closely related to water flow. In dry areas, species are susceptible to factors that interfere with the ecophysiological properties regulating water loss. Most hot arid areas are found at low latitudes where temperatures show striking extremes both in time and space. Living organisms are physiologically resistant and/or show adaptive behavior to these temperature extremes. Very little is known about the effects of toxicants on these key resistant and adaptive functions, although by extrapolation a few assumptions can be made. The effects of hyperthermia, for instance, can be aggravated by GSH depleting substances, and the temporary disabling effects characteristic of many pesticides may prove fatal under these circumstances. Most wet areas show a spatial concentration of both human activity and wildlife. In mesic zones, the contamination of water represents a health risk to both humans and other living organisms. The vast majority of aquatic communities are those inhabiting temporary pools and streams. Their populations are characterized by short reproductive cycles and/or long dormant stages. Toxicants affecting growth in these areas have been shown to have a deleterious effect. In a synthesis of existing knowledge the most prominent gaps are identified and priorities for further research are made.

Evaluation on the air-borne ultrasound-assisted hot air convection thin-layer drying performance of municipal sewage sludge.

PubMed

Sun, G Y; Chen, M Q; Huang, Y W

2017-01-01

The thin-layer drying behavior of the municipal sewage sludge in a laboratory-scale hot air forced convective dryer assisted with air-borne ultrasound was investigated in between 70 and 130°C hot air temperatures. The drying kinetics in the convective process alone were compared to that for ultrasound-assist process at three ultrasound powers (30, 90, 150W). The average drying rates within whole drying temperature range at ultrasound powers of 30, 90 and 150W increased by about 22.6%, 27.8% and 32.2% compared with the convective drying alone (without ultrasound). As the temperature increasing from 70°C to 130°C, there were maximum increasing ratios for the effective moisture diffusivities of the sewage sludge in both falling rate periods at ultrasonic power of 30W in comparison with other two high powers. In between the ultrasound powers of 0 and 30W, the effect of the power on the drying rate was significant, while its effect was not obvious over 30W. Therefore, the low ultrasonic power can be just set in the drying process. The values of the apparent activation energy in the first falling rate period were down from 13.52 to 12.78kJmol -1 , and from 17.21 to 15.10kJmol -1 for the second falling rate period with increasing the ultrasonic power from 30 to 150W. The values of the apparent activation energy in two falling rate periods with the ultrasound-assist were less than that for the hot air convective drying alone. Copyright © 2016 Elsevier B.V. All rights reserved.

Easy Meal

NASA Technical Reports Server (NTRS)

1978-01-01

The woman pictured below is sitting down to a nutritious, easily-prepared meal similar to those consumed by Apollo astronauts. The appetizing dishes shown were created simply by adding water to the contents of a Mountain House* Easy Meal package of freeze dried food. The Easy Meal line is produced by Oregon Freeze Dry Foods, Inc., Albany, Oreaon, a pioneer in freeze drying technology and a company long associated with NASA in developing suitable preparations for use on manned spacecraft. Designed to provide nutritionally balanced, attractive hot meals for senior adults, Easy Meal is an offshoot of a 1975-77 demonstration project managed by Johnson Space Center and called Meal System for the Elderly. The project sought ways to help the estimated 3.5 million elderly Americans who are unable to take advantage of existing meal programs. Such services are provided by federal, state and local agencies, but they are not available to many who live in rural areas, or others who are handicapped, temporarily ill or homebound for other reasons. Oregon Freeze Dry Foods was a participant in that multi-agency cooperative project. With its Easy Meal assortment of convenience foods pictured above left, the company is making commercially available meal packages similar to those distributed in the Meal System for the Elderly program. In the freeze drying process, water is extracted from freshly-cooked foods by dehydration at very low temperatures, as low as 50 I degrees below zero. Flavor is locked in by packaging the dried food in pouches which block out moisture and oxygen, the principal causes of food deterioration; thus the food can be stored for long periods without refrigeration. Meals are reconstituted by adding hot or cold water, depending on the type of food, and they are table ready in five to 10 minutes. Oregon Freeze Dry Foods offers five different meal packages and plans to expand the line.

[Thermal energy utilization analysis and energy conservation measures of fluidized bed dryer].

PubMed

Xing, Liming; Zhao, Zhengsheng

2012-07-01

To propose measures for enhancing thermal energy utilization by analyzing drying process and operation principle of fluidized bed dryers,in order to guide optimization and upgrade of fluidized bed drying equipment. Through a systematic analysis on drying process and operation principle of fluidized beds,the energy conservation law was adopted to calculate thermal energy of dryers. The thermal energy of fluidized bed dryers is mainly used to make up for thermal consumption of water evaporation (Qw), hot air from outlet equipment (Qe), thermal consumption for heating and drying wet materials (Qm) and heat dissipation to surroundings through hot air pipelines and cyclone separators. Effective measures and major approaches to enhance thermal energy utilization of fluidized bed dryers were to reduce exhaust gas out by the loss of heat Qe, recycle dryer export air quantity of heat, preserve heat for dry towers, hot air pipes and cyclone separators, dehumidify clean air in inlets and reasonably control drying time and air temperature. Such technical parameters such air supply rate, air inlet temperature and humidity, material temperature and outlet temperature and humidity are set and controlled to effectively save energy during the drying process and reduce the production cost.

Developing hot air assisted radio frequency drying for in-shell Macadamia nuts

USDA-ARS?s Scientific Manuscript database

Dehydration offers a means of preserving foods in a stable and safe condition as it reduces water activity and extends shelf-life of perishable agricultural products. The purpose of this study was to develop radio frequency (RF) drying protocols for in-shell macadamia nuts based on conventional hot ...

Effect of freezing, hot tumble drying and washing with eucalyptus oil on house dust mites in soft toys.

PubMed

Chang, Chin-Fu; Wu, Francis Fu-Sheng; Chen, Chi-Ying; Crane, Julian; Siebers, Rob

2011-09-01

Soft toys are a major source of house dust mites (HDM) and HDM allergens, and sleeping with soft toys is a significant risk factor for HDM sensitization. We studied three techniques to eliminate HDM from soft toys, namely freezing, hot tumble drying and washing with eucalyptus oil. Thirty-six toys (12 in each treatment group) were enumerated for live HDM by the heat escape method before and after freezing overnight, hot tumble drying for 1 h and washing in 0.2% to 0.4% eucalyptus oil. Freezing, hot tumble drying and washing with eucalyptus oil resulted in significant reductions in live HDM, an average reduction of 95.1%, 89.1% and 95.1%, respectively. Additionally, washing with eucalyptus oil resulted in a significant reduction in HDM allergens as well from a geometric mean of 9.12 μg/g to 0.37 μg/g (p = 0.033). These three HDM elimination techniques give parents of infants effective and acceptable methods of limiting HDM exposure. © 2011 John Wiley & Sons A/S.

Body temperature responses of Savanna Brown goat to the harmattan and hot-dry season

NASA Astrophysics Data System (ADS)

Igono, M. O.; Molokwu, E. C. I.; Aliu, Y. O.

1982-09-01

Rectal and vaginal temperature responses of the Savanna Brown goat indigenous to the Nigerian guinea savanna were determined during the harmattan and the hot-dry season. Measurements were made at 06:00h and at 14:00h after 8h exposure to field conditions. At the 06:00h measurements during the harmattan, all animals were observed to shiver. A significant (P<0.01) positive correlation was found between rectal (Tre) and vaginal temperatures. During the harmattan, mean Tre was 38.2‡C at 06:00h and 39.7‡C at 14:00h; the mean difference, δTre was 1.5‡C. During the hot-dry season, Tre at 06:00h was 38.1‡C, and at 14:00h, 38.7; δTre was 0.6‡C. It is concluded that the harmattan is thermally more stressful than the hot-dry season and that passive thermolability may not be an important mechanism in the Savanna Brown goat in adaptation to thermal stress.

Sewage sludge dewatering using flowing liquid metals

DOEpatents

Carlson, Larry W.

1986-01-01

A method and apparatus for reducing the moisture content of a moist sewage sludge having a moisture content of about 50% to 80% and formed of small cellular micro-organism bodies having internally confined water is provided. A hot liquid metal is circulated in a circulation loop and the moist sewage sludge is injected in the circulation loop under conditions of temperature and pressure such that the confined water vaporizes and ruptures the cellular bodies. The vapor produced, the dried sludge, and the liquid metal are then separated. Preferably, the moist sewage sludge is injected into the hot liquid metal adjacent the upstream side of a venturi which serves to thoroughly mix the hot liquid metal and the moist sewage sludge. The venturi and the drying zone after the venturi are preferably vertically oriented. The dried sewage sludge recovered is available as a fuel and is preferably used for heating the hot liquid metal.

Visiting a sauna: does inhaling hot dry air reduce common cold symptoms? A randomised controlled trial.

PubMed

Pach, Daniel; Knöchel, Bettina; Lüdtke, Rainer; Wruck, Katja; Willich, Stefan N; Witt, Claudia M

To compare the efficacy of applying hot dry air versus dry air at room temperature to the throat of patients with a newly acquired common cold using a symptom severity score. A randomised single-blind controlled trial with a treatment duration of 3 days and a follow-up period of 4 days was conducted at a sauna in Berlin, Germany. Between November 2007 and March 2008 and between September 2008 and April 2009, 157 patients with symptoms of the common cold were randomly assigned to an intervention group (n=80) and a control group (n=77). Participants in the intervention group inhaled hot dry air within a hot sauna, dressed in a winter coat, whereas participants in the control group inhaled dry air at room temperature within a hot sauna, also dressed in a winter coat. Area under the curve (AUC) summarising symptom severity over time (Days 2, 3, 5 and 7), symptom severity scores for individual days, intake of medication for the common cold and general ill feeling. No significant difference between groups was observed for AUC representing symptom severity over time (intervention group mean, 31.2 [SEM, 1.8]; control group mean, 35.1 [SEM, 2.3]; group difference, -3.9 [95% CI, -9.7 to 1.9]; P=0.19). However, significant differences between groups were found for medication use on Day 1 (P=0.01), symptom severity score on Day 2 (P=0.04), and participants' ratings of the effectiveness of the therapy on Day 7 (P=0.03). Inhaling hot air while in a sauna has no significant impact on overall symptom severity of the common cold. ClinicalTrials.gov identifier NCT00552981.

Effect of drying methods (microwave vacuum, freeze, hot air and sun drying) on physical, chemical and nutritional attributes of five pepper (Capsicum annuum var. annuum) cultivars.

PubMed

Maurya, Vaibhav Kumar; Gothandam, Kodiveri Muthukaliannan; Ranjan, Vijay; Shakya, Amita; Pareek, Sunil

2018-07-01

A randomized block design experiment was performed to investigate the influence of drying on the physical, chemical and nutritional quality attributes of five prominent cultivars of India under sun drying (SD) (mean temperature 35.5 °C, average daily radiation 5.26 kW h m -2 and mean relative humidity 73.66% RH), hot air drying (HD) at 65 °C, microwave vacuum drying (MVD) (800 W, 5 kPa) and freeze drying (FD) (-50 °C, 5 kPa). Water activity, pH, total phenolic content (TPC), ascorbic acid (AA), capsaicin, β-carotene, color and Scoville heat unit were studied. TPC, AA, capsaicin content, β-carotene, color and water activity were significantly affected by the drying method. FD was observed to be most efficient in minimizing the loss of color, capsaicin and β-carotene. The hotness of analyzed samples decreased in the order 'Bird's Eye' > 'Sannam S4' > 'CO-4' > 'PLR-1' > 'PKM-1' among the studied cultivars, and FD > MVD > HD > SD among the drying methods. The FD method was observed to be the most efficient drying method for retaining capsaicin content over other drying methods (SD, HD, MVD), whereas MVD was found to be most efficient in minimizing the loss to nutritional attributes for all five pepper cultivars. © 2018 Society of Chemical Industry. © 2018 Society of Chemical Industry.

Dry heat and hot water treatments for disinfesting cottonseed of Fusarium oxysporum f. sp. vasinfectum

USDA-ARS?s Scientific Manuscript database

The potential of low- and high-temperature dry heat, and hot water treatments, for disinfesting cottonseed of Fusarium oxysporum f. sp. vasinfectum was investigated. Naturally infected seeds from Louisiana were air-heated in incubators set at temperatures of 30, 35, and 40 degrees C for up to 24 we...

Rice chalky ring formation caused by temporal reduction in starch biosynthesis during osmotic adjustment under foehn-induced dry wind.

PubMed

Wada, Hiroshi; Masumoto-Kubo, Chisato; Gholipour, Yousef; Nonami, Hiroshi; Tanaka, Fukuyo; Erra-Balsells, Rosa; Tsutsumi, Koichi; Hiraoka, Kenzo; Morita, Satoshi

2014-01-01

Foehn-like extreme hot and dry wind conditions (34°C, >2.5 kPa vapor pressure deficit, and 7 m s(-1)) strongly affect grain quality in rice (Oryza sativa L.). This is a current concern because of the increasing frequency and intensity of combined heat and water-deficit stress under climate change. Foehn-induced dry wind conditions during the grain-filling stage increase ring-shaped chalkiness as a result of spatiotemporal reduction in starch accumulation in the endosperm, but kernel growth is sometimes maintained by osmotic adjustment. Here, we assess the effects of dry wind on chalky ring formation in environmentally controlled growth chambers. Our results showed that hot and dry wind conditions that lasted for >24 h dramatically increased chalky ring formation. Hot and dry wind conditions temporarily reduced panicle water potential to -0.65 MPa; however, kernel growth was maintained by osmotic adjustment at control levels with increased transport of assimilate to the growing kernels. Dynamic tracer analysis with a nano-electrospray-ionization Orbitrap mass spectrometer and quantitative polymerase chain reaction analysis revealed that starch degradation was negligible in the short-term treatment. Overall expression of starch synthesis-related genes was found to be down-regulated at moderately low water potential. Because the events observed at low water potential preceded the packing of starch granules in cells, we concluded that reduced rates of starch biosynthesis play a central role in the events of cellular metabolism that are altered at osmotic adjustment, which leads to chalky ring formation under short-term hot and dry wind conditions.

Effects of chemical composite, puffing temperature and intermediate moisture content on physical properties of potato and apple slices

NASA Astrophysics Data System (ADS)

Tabtaing, S.; Paengkanya, S.; Tanthong, P.

2017-09-01

Puffing technique is the process that can improve texture and volumetric of crisp fruit and vegetable. However, the effect of chemical composite in foods on puffing characteristics is still lack of study. Therefore, potato and apple slices were comparative study on their physical properties. Potato and apple were sliced into 2.5 mm thickness and 2.5 cm in diameter. Potato slices were treated by hot water for 2 min while apple slices were not treatment. After that, they were dried in 3 steps. First step, they were dried by hot air at temperature of 90°C until their moisture content reached to 30, 40, and 50 % dry basis. Then they were puffed by hot air at temperature of 130, 150, and 170°C for 2 min. Finally, they were dried again by hot air at temperature of 90°C until their final moisture content reached to 4% dry basis. The experimental results showed that chemical composite of food affected on physical properties of puffed product. Puffed potato had higher volume ratio than those puffed apple because potato slices contains starch. The higher starch content provided more hard texture of potato than those apples. Puffing temperature and moisture content strongly affected on the color, volume ratio, and textural properties of puffed potato slices. In addition, the high drying rate of puffed product observed at high puffing temperature and higher moisture content.

Chemical and physical pretreatments of fruits and vegetables: Effects on drying characteristics and quality attributes - a comprehensive review.

PubMed

Deng, Li-Zhen; Mujumdar, Arun S; Zhang, Qian; Yang, Xu-Hai; Wang, Jun; Zheng, Zhi-An; Gao, Zhen-Jiang; Xiao, Hong-Wei

2017-12-20

Pretreatment is widely used before drying of agro-products to inactivate enzymes, enhance drying process and improve quality of dried products. In current work, the influence of various pretreatments on drying characteristics and quality attributes of fruits and vegetables is summarized. They include chemical solution (hyperosmotic, alkali, sulfite and acid, etc.) and gas (sulfur dioxide, carbon dioxide and ozone) treatments, thermal blanching (hot water, steam, super heated steam impingement, ohmic and microwave heating, etc), and non-thermal process (ultrasound, freezing, pulsed electric field, and high hydrostatic pressure, etc). Chemical pretreatments effectively enhance drying kinetics, meanwhile, it causes soluble nutrients losing, trigger food safety issues by chemical residual. Conventional hot water blanching has significant effect on inactivating various undesirable enzymatic reactions, destroying microorganisms, and softening the texture, as well as facilitating drying rate. However, it induces undesirable quality of products, e.g., loss of texture, soluble nutrients, pigment and aroma. Novel blanching treatments, such as high-humidity hot air impingement blanching, microwave and ohmic heat blanching can reduce the nutrition loss and are more efficient. Non-thermal technologies can be a better alternative to thermal blanching to overcome these drawbacks, and more fundamental researches are needed for better design and scale up.

Using weather in forest management

Treesearch

Michael A. Fosberg

1986-01-01

The summer of 1933 in northwest Oregon had been exceptionally hot and dry. When in mid-August, hot, dry winds blew in from the east, all the fire crews were ready. But there were not enough of them. Scattered fires that started in the coast range merged into what became known as the Tillamook Bum. In 1986, the Forest Service is researching procedures to forecast...

Low temperature hot air drying of potato cubes subjected to osmotic dehydration and intermittent microwave: drying kinetics, energy consumption and product quality indexes

NASA Astrophysics Data System (ADS)

Dehghannya, Jalal; Bozorghi, Somayyeh; Heshmati, Maryam Khakbaz

2018-04-01

Hot-air drying is a slow energy-extensive process. Use of intermittent microwave (IM) in hot-air (HA) drying of food products is characterized with advantages including reduced process time, energy saving, and improved final quality. In this study, the effect of IM-HA drying following an osmotic dehydration (OD) pretreatment was analyzed on qualitative and quantitative properties of the output (i.e. effective moisture diffusion coefficient (Deff), shrinkage, bulk density, rehydration and energy consumption). Temperature and airflow velocity were fixed at 40°C and 1 m/s, respectively. The process variables included sucrose solution concentration at five levels (0 or control, 10, 30, 50 and 70 w/w%), microwave output power at four levels (0 or control, 360, 600 and 900 W), and pulse ratio at four levels (1, 2, 3 and 4). Use of osmotic dehydration in combination with IM-HA drying reduced the drying time by up to about 54%. Increasing the osmotic solution concentration to 30% and using higher pulse ratios increased the Deff. The lowest shrinkage and bulk density as well as the highest rehydration belonged to the 900 W microwave power and pulse ratio of 4. The lowest energy consumption was observed when using the 900 W power level, showing 63.27% less consumption than the HA drying method.

Controlling mechanisms of moisture diffusion in convective drying of leather

NASA Astrophysics Data System (ADS)

Benmakhlouf, Naima; Azzouz, Soufien; Monzó-Cabrera, Juan; Khdhira, Hechmi; ELCafsi, Afif

2017-04-01

Leather manufacturing involves a crucial energy-intensive drying stage in the finishing process to remove its residual moisture. It occurs several times in the tanning course. As it is the target of this paper to depict an experimental way to determine moisture diffusion in the convective drying of leather. The effective diffusion coefficient is estimated by a method derived from Fick's law and by analytic method. The effective diffusion coefficients are obtained from drying tests and the diffusivity behaviour is studied versus the controlling parameter such as the convective airflow temperature. The experiments were conducted at hot air temperatures of 40, 45, 50, 55 and 60 °C and hot air speed of 1 m/s. The hot air temperature had significant effect on the effective moisture diffusivity of the leather sample. The average effective moisture diffusivity in rosehip ranged between 5.87 × 10-11 and 14.48 × 10-11 m2/s for leather at the temperatures studied. Activation energy for convective drying was found to be 38.46 kJ/mol for leather. The obtained results fully confirm the theoretical study in which an exponentially increasing relationship between effective diffusivity and temperature is predicted. The results of this study provide a better understanding of the drying mechanisms and may lead to a series of recommendations for leather drying optimization. It opens the possibility for further investigations on the description of drying conditions.

Heat and mass transfer models to understand the drying mechanisms of a porous substrate.

PubMed

Songok, Joel; Bousfield, Douglas W; Gane, Patrick A C; Toivakka, Martti

2016-02-01

While drying of paper and paper coatings is expensive, with significant energy requirements, the rate controlling mechanisms are not currently fully understood. Two two-dimensional models are used as a first approximation to predict the heat transfer during hot air drying and to evaluate the role of various parameters on the drying rates of porous coatings. The models help determine the structural limiting factors during the drying process, while applying for the first time the recently known values of coating thermal diffusivity. The results indicate that the thermal conductivity of the coating structure is not the controlling factor, but the drying rate is rather determined by the thermal transfer process at the structure surface. This underlines the need for ensuring an efficient thermal transfer from hot air to coating surface during drying, before considering further measures to increase the thermal conductivity of porous coatings.

The effect of ambient temperature and humidity on interdialytic weight gains in end-stage renal disease patients on maintenance hemodialysis.

PubMed

Tapolyai, Mihály B; Faludi, Mária; Berta, Klára; Szarvas, Tibor; Lengvárszky, Zsolt; Molnar, Miklos Z; Dossabhoy, Neville R; Fülöp, Tibor

2016-07-01

Interdialytic weight gain (IDWG) is both a measure of dietary compliance and a well-established predictor of future adverse outcomes in dialysis patients. The impact of environmental conditions on IDWG in end-stage renal disease is little studied to date. We retrospectively reviewed IDWG for 100 consenting chronic end-stage renal disease patients undergoing thrice weekly in-center hemodiafiltration under three different climatic conditions in a Central European city: Weekend_1 was humid (93 %) and warm (24 °C); Weekend_2 was dry (38 %) and hot (33 °C); and Weekend_3 was dry (30 %) and warm (24 °C). The cohort's mean age was 60.9 ± 14.7 years, all were Eastern European, and 56 % were men. Residual urine output measured 100 [25-75 % quartiles: 0, 612] mL/day, single-pool Kt/V 1.4 ± 0.25, and albumin 40.1 ± 3.9 g/L. Mean IDWGs measured as follows: Weekend_1 ("humid-warm"): 2973 ± 1386 mL; Weekend_2 ("dry-hot"): 2685 ± 1368 mL and Weekend_3 ("dry-warm"): 2926 ± 1311 mL. Paired-samples testing for difference showed higher fluid gains on the humid-warm (239 mL; 95 % CI 21-458 mL; p = 0.032) and on the dry-warm weekends (222 mL; 95 % CI -8 to 453 mL, p = 0.059), when compared to the dry-hot weekend. Under the latter, dry-hot climatic condition, residual urine output lost its significance to impact IDWG during multiple regression analysis. While excess temperature may impact IDWG to a small degree, air humidity does not; the least weight gains occurred on the dry-hot weekend. However, the effects of both were minimal under continental summer conditions and are unlikely to explain large excesses of individual session-to-session variations.

Drying characteristics and quality of bananas under infrared radiation heating

USDA-ARS?s Scientific Manuscript database

Hot air (HA) drying of banana has low drying efficiency and results in undesirable product quality. The objectives of this research were to investigate the feasibility of infrared (IR) heating to improve banana drying rate, evaluate quality of the dried product, and establish models for predicting d...

Retention of antioxidant capacity of vacuum microwave dried cranberry.

PubMed

Leusink, Gwen J; Kitts, David D; Yaghmaee, Parastoo; Durance, Tim

2010-04-01

In this study, cranberries were dried by vacuum-microwave drying (VMD), freeze-drying (FD), or hot air-drying (AD), to compare the effects of different drying processes on both physical changes as well as the retention of bioactive components in dried samples. Total porosity (%) and average pore radius of dehydrated cranberries were greater using VMD compared to FD and AD (P < 0.05). Crude methanol cranberry powdered extracts were fractionated by solid phase extraction (SPE) into organic acid-, total phenolics-, anthocyanin-, or proanthocyanidin-enriched extracts, respectively. The chemical composition of the 60% acidified methanol fractions contained cyanidin-3-galactoside, cyanidin-3-arabinoside, peonidin-3-galactoside, and peonidin-3-arabinoside, as assessed by HPLC. Antioxidant activities of cranberry fractions were measured using chemical ORAC and ABTS methods. The 60% acidified methanol fraction had a significantly higher (P < 0.05) antioxidant potential than the other chemical fractions, which was largely attributed to the relatively higher anthocyanin content. In general, vacuum-microwave drying and freeze-drying resulted in similar retention of anthocyanins and antioxidant activity, which were both relatively higher (P < 0.05) than that recovered from cranberries dried by hot air drying.

Rice Chalky Ring Formation Caused by Temporal Reduction in Starch Biosynthesis during Osmotic Adjustment under Foehn-Induced Dry Wind

PubMed Central

Wada, Hiroshi; Masumoto-Kubo, Chisato; Gholipour, Yousef; Nonami, Hiroshi; Tanaka, Fukuyo; Erra-Balsells, Rosa; Tsutsumi, Koichi; Hiraoka, Kenzo; Morita, Satoshi

2014-01-01

Foehn-like extreme hot and dry wind conditions (34°C, >2.5 kPa vapor pressure deficit, and 7 m s−1) strongly affect grain quality in rice (Oryza sativa L.). This is a current concern because of the increasing frequency and intensity of combined heat and water-deficit stress under climate change. Foehn-induced dry wind conditions during the grain-filling stage increase ring-shaped chalkiness as a result of spatiotemporal reduction in starch accumulation in the endosperm, but kernel growth is sometimes maintained by osmotic adjustment. Here, we assess the effects of dry wind on chalky ring formation in environmentally controlled growth chambers. Our results showed that hot and dry wind conditions that lasted for >24 h dramatically increased chalky ring formation. Hot and dry wind conditions temporarily reduced panicle water potential to –0.65 MPa; however, kernel growth was maintained by osmotic adjustment at control levels with increased transport of assimilate to the growing kernels. Dynamic tracer analysis with a nano-electrospray-ionization Orbitrap mass spectrometer and quantitative polymerase chain reaction analysis revealed that starch degradation was negligible in the short-term treatment. Overall expression of starch synthesis-related genes was found to be down-regulated at moderately low water potential. Because the events observed at low water potential preceded the packing of starch granules in cells, we concluded that reduced rates of starch biosynthesis play a central role in the events of cellular metabolism that are altered at osmotic adjustment, which leads to chalky ring formation under short-term hot and dry wind conditions. PMID:25330305

Characterization of a penny-shaped reservoir in a hot dry rock

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sekine, H.; Mura, T.

1980-07-10

The mechanical stability of a penny-shaped revervoir is characterized by fracture mechanics including thermoelastic effects in connection with research into the extraction of geothermal energy from hot dry rocks. The condition for stability of a reservoir, which is not changing radius by propagating or closing, requires 0m/sub 0/>m/sub asterisk/; and case 3; m/sub 0/=m/sub asterisk/.

Storage capacity in hot dry rock reservoirs

DOEpatents

Brown, D.W.

1997-11-11

A method is described for extracting thermal energy, in a cyclic manner, from geologic strata which may be termed hot dry rock. A reservoir comprised of hot fractured rock is established and water or other liquid is passed through the reservoir. The water is heated by the hot rock, recovered from the reservoir, cooled by extraction of heat by means of heat exchange apparatus on the surface, and then re-injected into the reservoir to be heated again. Water is added to the reservoir by means of an injection well and recovered from the reservoir by means of a production well. Water is continuously provided to the reservoir and continuously withdrawn from the reservoir at two different flow rates, a base rate and a peak rate. Increasing water flow from the base rate to the peak rate is accomplished by rapidly decreasing backpressure at the outlet of the production well in order to meet periodic needs for amounts of thermal energy greater than a baseload amount, such as to generate additional electric power to meet peak demands. The rate of flow of water provided to the hot dry rock reservoir is maintained at a value effective to prevent depletion of the liquid inventory of the reservoir. 4 figs.

Storage capacity in hot dry rock reservoirs

DOEpatents

Brown, Donald W.

1997-01-01

A method of extracting thermal energy, in a cyclic manner, from geologic strata which may be termed hot dry rock. A reservoir comprised of hot fractured rock is established and water or other liquid is passed through the reservoir. The water is heated by the hot rock, recovered from the reservoir, cooled by extraction of heat by means of heat exchange apparatus on the surface, and then re-injected into the reservoir to be heated again. Water is added to the reservoir by means of an injection well and recovered from the reservoir by means of a production well. Water is continuously provided to the reservoir and continuously withdrawn from the reservoir at two different flow rates, a base rate and a peak rate. Increasing water flow from the base rate to the peak rate is accomplished by rapidly decreasing backpressure at the outlet of the production well in order to meet periodic needs for amounts of thermal energy greater than a baseload amount, such as to generate additional electric power to meet peak demands. The rate of flow of water provided to the hot dry rock reservoir is maintained at a value effective to prevent depletion of the liquid

IS ISLAND PARK A HOT DRY ROCK SYSTEM?

USGS Publications Warehouse

Hoover, D.B.; Pierce, Herbert A.; Long, C.L.

1985-01-01

The Island Park-Yellowstone National Park region comprises a complex caldera system which has formed over the last 2 m. y. The caldera system has been estimated to contain 50% of the total thermal energy remaining in all young igneous systems in the United States. As the result of a reexamination of the data and recent electrical work in the area, the authors now postulate that much of the area where the first- and second-stage calderas developed is underlain by a solidified but still hot pluton. They postulate that the pluton represents a significant hot-dry-rock resource for the United States.

Preliminary report on radiocarbon dating of cryptoendolithic microorganisms

NASA Technical Reports Server (NTRS)

Bonani, G.; Friedmann, E. I.; Ocampo-Friedmann, R.; McKay, C. P.; Woelfli, W.

1988-01-01

The existence of microbial communities living inside desert rocks has been reported by FRIEDMANN et al. (1967, 1976), first in rocks collected from the hot and dry Negev desert and later in rocks in the frigid Ross Desert of Southern Victoria Land, Antarctica. The extremely inhospitable climatic conditions in both places has led to the suggestion that these organisms have very low rates of metabolism and may, in addition, be very old (FRIEDMANN 1982). Our preliminary measurements showed a 14C deficiency indicating a carbon age in the order of magnitude of 10(3) years.

The dependence of permeability on effective stress from flow tests at hot dry rock reservoirs at Rosemanowes (Cornwall) and Fenton Hill (New Mexico)

USGS Publications Warehouse

Nathenson, M.

1999-01-01

Effective stress is the primary control on permeability and thus on flow and water loss for two-well hot dry rock systems involving injection and production that have been tested to date. Theoretical relations are derived for the flow between an injector and producer, including the dependence of permeability on effective stress. Four relations for permeability as a function of effective stress are used to match field data for the hot dry rock systems at Rosemanowes, Cornwall, and Fenton Hill, New Mexico. The flow and water loss behavior of these systems are well explained by the influence of effective stress on permeability. All four relations for permeability as a function of effective stress are successful in matching the field data, but some have difficulty in determining unique values for elastic and hydrologic parameters.Effective stress is the primary control on permeability and thus on flow and water loss for two-well hot dry rock systems involving injection and production that have been tested to date. Theoretical relations are derived for the flow between an injector and producer, including the dependence of permeability on effective stress. Four relations for permeability as a function of effective stress are used to match field data for the hot dry rock systems at Rosemanowes, Cornwall, and Fenton Hill, New Mexico. The flow and water loss behavior of these systems are well explained by the influence of effective stress on permeability. All four relations for permeability as a function of effective stress are successful in matching the field data, but some have difficulty in determining unique values for elastic and hydrologic parameters.

Degradation of carotenoids in apricot (Prunus armeniaca L.) during drying process.

PubMed

Fratianni, Alessandra; Albanese, Donatella; Mignogna, Rossella; Cinquanta, Luciano; Panfili, Gianfranco; Di Matteo, Marisa

2013-09-01

Carotenoids are natural compounds whose nutritional importance comes from the provitamin A activity of some of them and their protection against several serious human disorders. The degradation of carotenoids was investigated during apricot drying by microwave and convective hot-air at 60 and 70 °C. Seven carotenoids were identified: antheraxanthin, lutein, zeaxanthin, β-cryptoxanthin, 13-cis-β-carotene, all-trans-β-carotene and 9-cis-β-carotene; among these, all-trans-β-carotene was found to be about 50 % of total carotenoids. First-order kinetic models were found to better describe all-trans-β-carotene reduction during drying, with a degradation rate constant (k1) that increased two folds when temperatures increased by 10 °C, in both methods. No differences were found in k1 between apricots dried by hot air at 70 °C (k1 = 0.0340 h(-1)) and by microwave at 60 °C. The evolution of total carotenoids (117.1 mg/kg on dry basis) during drying highlighted a wider decrease (about 50%) when microwave heating was employed, for both set temperatures. Antheraxantin was found to be the carotenoid most susceptible to heat, disappearing at 6 h during both trials with microwave as well as during convective hot-air at 70 °C. For this reason, antheraxanthin could be a useful marker for the evaluation of thermal damage due to the drying process. Also the degree of isomerization of all-trans-β-carotene could be a useful marker for the evaluation of the drying process.

Physicochemical and phytochemical properties of cold and hot water extraction from Hibiscus sabdariffa.

PubMed

Ramirez-Rodrigues, Milena M; Plaza, Maria L; Azeredo, Alberto; Balaban, Murat O; Marshall, Maurice R

2011-04-01

Hibiscus cold (25 °C) and hot (90 °C) water extracts were prepared in various time-temperature combinations to determine equivalent extraction conditions regarding their physicochemical and phytochemical properties. Equivalent anthocyanins concentration was obtained at 25 °C for 240 min and 90 °C for 16 min. Total phenolics were better extracted with hot water that also resulted in a higher antioxidant capacity in these extracts. Similar polyphenolic profiles were observed between fresh and dried hibiscus extracts. Hibiscus acid and 2 derivatives were found in all extracts. Hydroxybenzoic acids, caffeoylquinic acids, flavonols, and anthocyanins constituted the polyphenolic compounds identified in hibiscus extracts. Two major anthocyanins were found in both cold and hot extracts: delphynidin-3-sambubioside and cyanidin-3-sambubioside. In general, both cold and hot extractions yielded similar phytochemical properties; however, under cold extraction, color degradation was significantly lower and extraction times were 15-fold longer. Hibiscus beverages are prepared from fresh or dried calyces by a hot extraction and pasteurized, which can change organoleptic, nutritional, and color attributes. Nonthermal technologies such as dense phase carbon dioxide may maintain their fresh-like color, flavor, and nutrients. This research compares the physicochemical and phytochemical changes resulting from a cold and hot extraction of fresh and dried hibiscus calyces and adds to the knowledge of work done on color, quality attributes, and antioxidant capacity of unique tropical products. In addition, the research shows how these changes could lead to alternative nonthermal processes for hibiscus.

Diurnal, seasonal, and sex patterns of heart rate in grip-restrained African giant rats (Cricetomys gambianus, Waterhouse).

PubMed

Dzenda, Tavershima; Ayo, Joseph O; Sinkalu, Victor O; Yaqub, Lukuman S

2015-10-01

This study was carried out to determine heart rate (HR) values, including diurnal, seasonal, and sex patterns, in the African giant rat (Cricetomys gambianus, Waterhouse). HR was measured using stethoscope in grip-restrained African giant rats of either sex (103 bucks and 98 does), live-trapped from a tropical Savannah, and caged individually in the laboratory during the harmattan (cold-dry), hot-dry, and rainy seasons over a 3-year period. The HR fluctuated between 90 and 210 beats per minute (bpm) throughout the study period. Diurnal changes in HR (mean ± SEM) during the hot-dry and rainy seasons were nonsignificant (P > 0.05), but the morning and afternoon values differed (P < 0.01) during the cold-dry season. The HR varied (P < 0.05) among seasons, with peak, nadir, and moderate values recorded during the cold-dry (165.8 ± 0.51 bpm), hot-dry (153.1 ± 0.74 bpm), and rainy (163.4 ± 0.70 bpm) seasons, respectively. Mean HR of bucks was lower than that of does during the cold-dry (P < 0.0001) and hot-dry (P < 0.01) seasons, but sex difference during the rainy season was insignificant (P > 0.05). Overall, mean HR was lower (P < 0.0001) in bucks (158.8 ± 0.53 bpm) than in does (164.8 ± 0.53 bpm). In conclusion, values of HR in African giant rats are shown for the first time. Season, sex, and daytime influenced the HR, and should be considered during clinical evaluations of the rats. © 2015 The Authors. Physiological Reports published by Wiley Periodicals, Inc. on behalf of the American Physiological Society and The Physiological Society.

Scabies

MedlinePlus

... too. Wash clothing, sheets, and towels in hot water and dry on a hot setting. Put stuffed animals and other items that ... Sexually Transmitted Diseases (STDs) Tips for Taking Care of Your Skin ...

40 CFR 420.131 - Specialized definitions.

Code of Federal Regulations, 2012 CFR

2012-07-01

....131 Specialized definitions. As used in this subpart: (a) The term briquetting operations means a hot... gaseous (carbon monoxide-carbon dioxide, hydrogen) or solid reactants. (c) The term forging means the hot... of briquettes manufactured by hot or cold agglomeration processes. (e) For direct reduced iron (DRI...

40 CFR 420.131 - Specialized definitions.

Code of Federal Regulations, 2013 CFR

2013-07-01

....131 Specialized definitions. As used in this subpart: (a) The term briquetting operations means a hot... gaseous (carbon monoxide-carbon dioxide, hydrogen) or solid reactants. (c) The term forging means the hot... of briquettes manufactured by hot or cold agglomeration processes. (e) For direct reduced iron (DRI...

40 CFR 420.131 - Specialized definitions.

Code of Federal Regulations, 2011 CFR

2011-07-01

....131 Specialized definitions. As used in this subpart: (a) The term briquetting operations means a hot... gaseous (carbon monoxide-carbon dioxide, hydrogen) or solid reactants. (c) The term forging means the hot... of briquettes manufactured by hot or cold agglomeration processes. (e) For direct reduced iron (DRI...

40 CFR 420.131 - Specialized definitions.

Code of Federal Regulations, 2014 CFR

2014-07-01

....131 Specialized definitions. As used in this subpart: (a) The term briquetting operations means a hot... gaseous (carbon monoxide-carbon dioxide, hydrogen) or solid reactants. (c) The term forging means the hot... of briquettes manufactured by hot or cold agglomeration processes. (e) For direct reduced iron (DRI...

Mass transfer characteristics of bisporus mushroom ( Agaricus bisporus) slices during convective hot air drying

NASA Astrophysics Data System (ADS)

Ghanbarian, Davoud; Baraani Dastjerdi, Mojtaba; Torki-Harchegani, Mehdi

2016-05-01

An accurate understanding of moisture transfer parameters, including moisture diffusivity and moisture transfer coefficient, is essential for efficient mass transfer analysis and to design new dryers or improve existing drying equipments. The main objective of the present study was to carry out an experimental and theoretical investigation of mushroom slices drying and determine the mass transfer characteristics of the samples dried under different conditions. The mushroom slices with two thicknesses of 3 and 5 mm were dried at air temperatures of 40, 50 and 60 °C and air flow rates of 1 and 1.5 m s-1. The Dincer and Dost model was used to determine the moisture transfer parameters and predict the drying curves. It was observed that the entire drying process took place in the falling drying rate period. The obtained lag factor and Biot number indicated that the moisture transfer in the samples was controlled by both internal and external resistance. The effective moisture diffusivity and the moisture transfer coefficient increased with increasing air temperature, air flow rate and samples thickness and varied in the ranges of 6.5175 × 10-10 to 1.6726 × 10-9 m2 s-1 and 2.7715 × 10-7 to 3.5512 × 10-7 m s-1, respectively. The validation of the Dincer and Dost model indicated a good capability of the model to describe the drying curves of the mushroom slices.

Improvement in storage stability of infrared dried rough rice

USDA-ARS?s Scientific Manuscript database

The objective of this study was to develop infrared drying (IRD) method to improve the stability of physicochemical properties of rough rice during storage. The effect of IRD on the physicochemical properties of stored rough rice was compared with that of hot air drying (HAD) and ambient air drying ...

Effects of pulsed electric fields pretreatment and drying method on drying characteristics and nutritive quality of blueberries

USDA-ARS?s Scientific Manuscript database

Fresh blueberries were pretreated with pulsed electric fields (PEF) at 2 kV/cm and then dried at 45, 60 and 75 degrees C by conventional hot air or vacuum drying. Drying characteristics and changes in contents of moisture, anthocyanin, total phenolics, vitamin C, and antioxidant activity in the blu...

Effect of dehydration on raspberries: polyphenol and anthocyanin retention, antioxidant capacity, and antiadipogenic activity.

PubMed

Mejia-Meza, E I; Yáñez, J A; Remsberg, C M; Takemoto, J K; Davies, N M; Rasco, B; Clary, C

2010-01-01

Fresh and dried raspberries prepared by freeze drying (FD), microwave-vacuum (MIVAC), hot-air drying (HAD), and a combination of hot-air drying and microwave-vacuum (HAD/MIVAC) drying methods were evaluated for polyphenol retention, total polyphenol and anthocyanin contents, total antioxidant capacity, and antiadipogenic activity (the inhibition of fat cell development). Ellagic acid and quercetin were present in the largest concentrations in fresh and dehydrated raspberries. Dehydration led to a loss of polyphenols and anthocyanins and antioxidant capacity. Polyphenols (aglycone form) were retained in the greatest amount: 20% (freeze dried) to 30% (HAD/MIVAC) (fresh = 100%). A total of 30% of polyphenols (glycoside form) were retained in raspberries dried by the HAD/MIVAC methods with 5% of retention observed for raspberries dried by FD, HAD, or MIVAC. FD and MIVAC resulted in higher retention of anthocyanins (aglycone form) than other drying methods. It was also observed that antioxidant activity was reduced by dehydration. Adipogenesis was inhibited by polyphenolic glycosides (30%) and aglycones (30% to 40%) in fresh and HAD/MIVAC raspberries. Extracts from dried raspberries by HAD/MIVAC methods were relatively more effective at inhibiting adipogenesis compared to HAD and FD dried raspberries.

Material handling systems for the fluidized-bed combustion boiler at Rivesville, West Virginia

NASA Technical Reports Server (NTRS)

Branam, J. G.; Rosborough, W. W.

1977-01-01

The 300,000 lbs/hr steam capacity multicell fluidized-bed boiler (MFB) utilizes complex material handling systems. The material handling systems can be divided into the following areas: (1) coal preparation; transfer and delivery, (2) limestone handling system, (3) fly-ash removal and (4) bed material handling system. Each of the above systems are described in detail and some of the potential problem areas are discussed. A major potential problem that exists is the coal drying system. The coal dryer is designed to use 600 F preheated combustion air as drying medium and the dryer effluent is designed to enter a hot electrostatic precipitator (730 F) after passage through a cyclone. Other problem areas to be discussed include the steam generator coal and limestone feed system which may have operating difficulties with wet coal and/or coal fines.

40 CFR 60.91 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... PERFORMANCE FOR NEW STATIONARY SOURCES Standards of Performance for Hot Mix Asphalt Facilities § 60.91... Act and in subpart A of this part. (a) Hot mix asphalt facility means any facility, as described in § 60.90, used to manufacture hot mix asphalt by heating and drying aggregate and mixing with asphalt...

40 CFR 60.91 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... PERFORMANCE FOR NEW STATIONARY SOURCES Standards of Performance for Hot Mix Asphalt Facilities § 60.91... Act and in subpart A of this part. (a) Hot mix asphalt facility means any facility, as described in § 60.90, used to manufacture hot mix asphalt by heating and drying aggregate and mixing with asphalt...

40 CFR 60.91 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... PERFORMANCE FOR NEW STATIONARY SOURCES Standards of Performance for Hot Mix Asphalt Facilities § 60.91... Act and in subpart A of this part. (a) Hot mix asphalt facility means any facility, as described in § 60.90, used to manufacture hot mix asphalt by heating and drying aggregate and mixing with asphalt...

40 CFR 60.91 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... PERFORMANCE FOR NEW STATIONARY SOURCES Standards of Performance for Hot Mix Asphalt Facilities § 60.91... Act and in subpart A of this part. (a) Hot mix asphalt facility means any facility, as described in § 60.90, used to manufacture hot mix asphalt by heating and drying aggregate and mixing with asphalt...

40 CFR 60.91 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... PERFORMANCE FOR NEW STATIONARY SOURCES Standards of Performance for Hot Mix Asphalt Facilities § 60.91... Act and in subpart A of this part. (a) Hot mix asphalt facility means any facility, as described in § 60.90, used to manufacture hot mix asphalt by heating and drying aggregate and mixing with asphalt...

Evapotranspiration and water balance in a hot pepper (Capsicum frutescens L.) field during a dry season in the tropics

NASA Astrophysics Data System (ADS)

Laban, S.; Oue, H.; Rampisela, D. A.

2018-05-01

Evapotranspiration and water balance in a hot pepper (Capsicum frutescens L.) field during the 2nd dry season were analyzed in this study. Actual evapotranspiration (ET) was estimated by Bowen Ratio Energy Budget (BREB) method, potential evaporation (EP) was calculated by Penman method, and irrigation volume of water was measured manually. Meteorological instruments were installed in the experimental field during hot pepper cultivation. Leaf area index increased during the growing stages where the highest LAI of 1.65 in the generative stage. The daily average of ET was 1.94 and EP was 6.71 mm resulting in low Kc. The Kc values were significantly different between stage to stage under T-test analysis (α = 0.05). Moreover, Kc in every stage could be related to soil water content (SWC) in logarithmic function. Totally, ET during hot pepper cultivation was 179.19 mm, while rainfall was 180.0 mm and irrigation water was 27.42 mm. However, there was a water shortages during vegetative and generative stages. This study suggested that consumptive water of hot pepper was complimented by soil and groundwater under the condition of water shortages in the vegetative and generative stages during the 2nd dry season.

Drying kinetics of apricot halves in a microwave-hot air hybrid oven

NASA Astrophysics Data System (ADS)

Horuz, Erhan; Bozkurt, Hüseyin; Karataş, Haluk; Maskan, Medeni

2017-06-01

Drying behavior and kinetics of apricot halves were investigated in a microwave-hot air domestic hybrid oven at 120, 150 and 180 W microwave power and 50, 60 and 70 °C air temperature. Drying operation was finished when the moisture content reached to 25% (wet basis) from 77% (w.b). Increase in microwave power and air temperature increased drying rates and reduced drying time. Only falling rate period was observed in drying of apricot halves in hybrid oven. Eleven mathematical models were used for describing the drying kinetics of apricots. Modified logistic model gave the best fitting to the experimental data. The model has never been used to explain drying behavior of any kind of food materials up to now. Fick's second law was used for determination of both effective moisture diffusivity and thermal diffusivity values. Activation energy values of dried apricots were calculated from Arrhenius equation. Those that obtained from effective moisture diffusivity, thermal diffusivity and drying rate constant values ranged from 31.10 to 39.4 kJ/mol, 29.56 to 35.19 kJ/mol, and 26.02 to 32.36 kJ/mol, respectively.

Effects of hot, humid weather on milk temperature, dry matter intake, and milk yield of lactating dairy cows.

PubMed

West, J W; Mullinix, B G; Bernard, J K

2003-01-01

Lactating cows were exposed to moderate and hot, humid weather to determine the effect of increasing ambient temperature, relative humidity, or temperature-humidity index (THI) on intake, milk yield, and milk temperature. Minimum and maximum temperatures averaged 17.9 and 29.5 degrees C (cool period) and 22.5 and 34.4 degrees C (hot period), and minimum and maximum THI averaged 63.8 and 76.6 (cool period) and 72.1 and 83.6 (hot period). Environmental conditions had minor effects on intake and milk yield during the cool period. During the hot period, the THI 2 d earlier and mean air temperature 2 d earlier had the greatest impact on milk yield and DMI, respectively. Both breeds maintained milk temperature within normal ranges during the cool period, but Holstein and Jersey p.m. milk temperatures averaged 39.6 and 39.2 degrees C during the hot period. Current day mean air temperature during the hot period had the greatest impact on cow p.m. milk temperature, and minimum air temperature had the greatest influence on a.m. milk temperature. Dry matter intake and milk yield declined linearly with respective increases in air temperature or THI during the hot period and milk temperature increased linearly with increasing air temperature. Dry matter intake and milk yield both exhibited a curvilinear relationship with milk temperature. Environmental modifications should target the effects of high temperatures on cow body temperature and should modify the environment at critical times during the day when cows are stressed, including morning hours when ambient temperatures are typically cooler and cows are not assumed to be stressed.

Degradation kinetics of cyanidin 3-O-glucoside and cyanidin 3-O-rutinoside during hot air and vacuum drying in mulberry (Morus alba L.) fruit: A comparative study based on solid food system.

PubMed

Zhou, Mo; Chen, Qinqin; Bi, Jinfeng; Wang, Yixiu; Wu, Xinye

2017-08-15

The aim of this study is to ascertain the degradation kinetic of anthocyanin in dehydration process of solid food system. Mulberry fruit was treated by hot air and vacuum drying at 60 and 75°C. The contents of cyanidin 3-O-glucoside and cyanidin 3-O-rutinoside were determined by using high performance liquid chromatography. Kinetic and thermodynamic parameters were calculated for analysing the degradation characteristics. Model fitting results showed monomeric anthocyanin degradations were followed the second-order kinetic. Vacuum drying presented high kinetic rate constants and low t 1/2 values. Thermodynamic parameters including the activation energy, enthalpy change and entropy change appeared significant differences between hot air and vacuum drying. Both heating techniques showed similar effects on polyphenol oxidase activities. These results indicate the anthocyanin degradation kinetic in solid food system is different from that in liquid and the oxygen can be regarded as a catalyst to accelerate the degradation. Copyright © 2017 Elsevier Ltd. All rights reserved.

The influence of microwave-assisted drying techniques on the rehydration behavior of blueberries (Vaccinium corymbosum L.).

PubMed

Zielinska, Magdalena; Markowski, Marek

2016-04-01

The aim of this study was to determine the effect of: (a) different drying methods, (b) hot air temperature in a convection oven, and (c) the moisture content of fruits dehydrated by multi-stage drying which involves a transition between different stages of drying, on the rehydration kinetics of dry blueberries. Models describing rehydration kinetics were also studied. Blueberries dehydrated by multi-stage microwave-assisted drying, which involved a hot air pre-drying step at 80 °C until the achievement of a moisture content of 1.95 kg H2O kg(-1)DM, were characterized by significantly higher rates of initial and successive rehydration as well as smaller initial loss of soluble solids in comparison with the samples dried by other methods. The highest initial rehydration rate and the smallest loss of soluble solids after 30 min of soaking were determined at 0.46 min(-1) and 0.29 kg DM kg(-1)DM, respectively. The Peleg model and the first-order-kinetic model fit the experimental data well. Copyright © 2015 Elsevier Ltd. All rights reserved.

Image analysis and green tea color change kinetics during thin-layer drying.

PubMed

Shahabi, Mohammad; Rafiee, Shahin; Mohtasebi, Seyed Saeid; Hosseinpour, Soleiman

2014-09-01

This study was conducted to investigate the effect of air temperature and air flow velocity on kinetics of color parameter changes during hot-air drying of green tea, to obtain the best model for hot-air drying of green tea, to apply a computer vision system and to study the color changes during drying. In the proposed computer vision system system, at first RGB values of the images were converted into XYZ values and then to Commission International d'Eclairage L*a*b* color coordinates. The obtained color parameters of L*, a* and b* were calibrated with Hunter-Lab colorimeter. These values were also used for calculation of the color difference, chroma, hue angle and browning index. The values of L* and b* decreased, while the values of a* and color difference (ΔE*ab ) increased during hot-air drying. Drying data were fitted to three kinetic models. Zero, first-order and fractional conversion models were utilized to describe the color changes of green tea. The suitability of fitness was determined using the coefficient of determination (R (2)) and root-mean-square error. Results showed that the fraction conversion model had more acceptable fitness than the other two models in most of color parameters. © The Author(s) 2013 Reprints and permissions: sagepub.co.uk/journalsPermissions.nav.

Extremely low prevalence of Batrachochytrium dendrobatidis in frog populations from neotropical dry forest of Costa Rica supports the existence of a climatic refuge from disease.

PubMed

Zumbado-Ulate, Héctor; Bolaños, Federico; Gutiérrez-Espeleta, Gustavo; Puschendorf, Robert

2014-12-01

Population declines and extinctions of numerous species of amphibians, especially stream-breeding frogs, have been linked to the emerging infectious disease chytridiomycosis, caused by the chytrid fungus, Batrachochytrium dendrobatidis. In Central America, most of the 34 species of the Craugastor punctariolus species group have disappeared in recent years in high- and low-elevation rainforests. Distribution models for B. dendrobatidis and the continuous presence of the extirpated stream-dwelling species, Craugastor ranoides, in the driest site of Costa Rica (Santa Elena Peninsula), suggest that environmental conditions might restrict the growth and development of B. dendrobatidis, existing as a refuge from chytridiomycosis-driven extinction. We conducted field surveys to detect and quantify the pathogen using Real-time PCR in samples from 15 species of frogs in two locations of tropical dry forest. In Santa Elena Peninsula, we swabbed 310 frogs, and only one sample of the species, C. ranoides, tested positive for B. dendrobatidis (prevalence <0.1%). In Santa Rosa Station, we swabbed 100 frogs, and nine samples from three species tested positive (prevalence = 9.0%). We failed to detect signs of chytridiomycosis in any of the 410 sampled frogs, and low quantities of genetic equivalents (between 0 and 1073) were obtained from the ten positive samples. The difference in the prevalence between locations might be due not only to the hotter and drier conditions of Santa Elena Peninsula but also to the different compositions of species in both locations. Our results suggest that B. dendrobatidis is at the edge of its distribution in these dry and hot environments of tropical dry forest. This study supports the existence of climatic refuges from chytridiomycosis and highlights the importance of tropical dry forest conservation for amphibians in the face of epidemic disease.

Xerosis

MedlinePlus

... Causes Dry skin can be caused by: The climate, such as cold, dry winter air or hot, ... Medical Dermatology, Associate Professor of Dermatology, Mayo Medical School, Scottsdale, AZ. Also reviewed by David Zieve, MD, ...

Effects of hot air and freeze drying methods on antioxidant activity, colour and some nutritional characteristics of strawberry tree (Arbutus unedo L) fruit.

PubMed

Orak, H H; Aktas, T; Yagar, H; İsbilir, S Selen; Ekinci, N; Sahin, F Hasturk

2012-08-01

Antioxidant activity, colour and some nutritional properties of hot air and freeze-dried strawberry tree (Arbutus unedo L.) fruits were investigated. Additionally, the effects of two pre-treatments, namely ethyl oleate and water blanching, were compared in terms of drying characteristics. For determination of antioxidant activities in ethanol extracts, two different analytical methods were used: 1,1-diphenyl-2-picrylhydrazyl scavenging activity and β-carotene bleaching activity. As a result, the ethyl oleate pre-treatment shortened the drying time by hot air method and gave a higher 1,1-diphenyl-2-picrylhydrazyl scavenging activity (82.16 ± 0.34%), total phenolic content (7.62 ± 1.09 µg GAE/g extract), ascorbic acid content (236.93 ± 20.14 mg/100 g), besides hydromethylfurfural was not observed. Freeze-dried fruits exhibited higher ascorbic acid content (368.63 ± 17.16 mg/100 g) than those fresh fruits (231.33 ± 19.51 mg/100 g) and nearly 1,1-diphenyl-2-picrylhydrazyl activity (93.52 ± 0.41 %) to fresh fruits (94.03 ± 1.18%). Colour characteristics, sugar content and mineral contents of fruits were significantly affected by pre-treatments and drying methods (p < 0.05). It is concluded that the drying of strawberry tree fruits should bring a valuable and attractive foodstuff to food industry due to the rich nutritional components, antioxidant activity and colour. Another conclusion from this study is that the freeze-drying is the best drying method to keep the nutritional value, antioxidant activity and sensory properties of fruits.

Agriculturally Relevant Climate Extremes and Their Trends in the World's Major Growing Regions

NASA Astrophysics Data System (ADS)

Zhu, Xiao; Troy, Tara J.

2018-04-01

Climate extremes can negatively impact crop production, and climate change is expected to affect the frequency and severity of extremes. Using a combination of in situ station measurements (Global Historical Climatology Network's Daily data set) and multiple other gridded data products, a derived 1° data set of growing season climate indices and extremes is compiled over the major growing regions for maize, wheat, soybean, and rice for 1951-2006. This data set contains growing season climate indices that are agriculturally relevant, such as the number of hot days, duration of dry spells, and rainfall intensity. Before 1980, temperature-related indices had few trends; after 1980, statistically significant warming trends exist for each crop in the majority of growing regions. In particular, crops have increasingly been exposed to extreme hot temperatures, above which yields have been shown to decline. Rainfall trends are less consistent compared to temperature, with some regions receiving more rainfall and others less. Anomalous temperature and precipitation conditions are shown to often occur concurrently, with dry growing seasons more likely to be hotter, have larger drought indices, and have larger vapor pressure deficits. This leads to the confluence of a variety of climate conditions that negatively impact crop yields. These results show a consistent increase in global agricultural exposure to negative climate conditions since 1980.

The furnace in the basement: Part 1, The early days of the Hot Dry Rock Geothermal Energy Program, 1970--1973

DOE Office of Scientific and Technical Information (OSTI.GOV)

Smith, M.C.

1995-09-01

This report presents the descriptions of the background information and formation of the Los Alamos Scientific Laboratory Geothermal Energy Group. It discusses the organizational, financial, political, public-relations,geologic, hydrologic, physical, and mechanical problems encountered by the group during the period 1970--1973. It reports the failures as well as the successes of this essential first stage in the development of hot dry rock geothermal energy systems.

New Zealand geothermal: Wairakei -- 40 years

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

This quarterly bulletin highlights the geothermal developments in New Zealand with the following articles: A brief history of the Wairakei geothermal power project; Geothermal resources in New Zealand -- An overview; Domestic and commercial heating and bathing -- Rotorua area; Kawerau geothermal development: A case study; Timber drying at Kawerau; Geothermal greenhouses at Kawerau; Drying of fibrous crops using geothermal steam and hot water at the Taupo Lucerne Company; Prawn Park -- Taupo, New Zealand; Geothermal orchids; Miranda hot springs; and Geothermal pipeline.

Bioactive compounds of four hot pepper varieties (Capsicum annuum L.), antioxidant capacity, and intestinal bioaccessibility.

PubMed

Hervert-Hernández, Deisy; Sáyago-Ayerdi, Sonia G; Goñi, Isabel

2010-03-24

Pepper fruits (Capsicum annuum) contain a wide array of phytochemicals with well-known antioxidant properties. Since bioactive compounds depend on their bioavailability to exert beneficial effects, it was crucial to estimate the extent of release from the food matrix and thus their bioaccessibility. Accordingly, we determined the individual carotenoid and phenolic content as well as the antioxidant properties of four red hot dried cultivars (Capsicum annuum L.) of high consumption in Mexico and estimated the extent of intestinal bioaccessibility of carotenoids with significance in human health, beta-carotene, beta-cryptoxanthin, and zeaxanthin, using an in vitro gastrointestinal model. Hot dried peppers at ripe stage had a high content of bioactive compounds that exhibited significant antioxidant properties (26-80 micromol trolox equivalents/g of dry matter), such as polyphenols (>2000 mg/100 g of dry matter) and carotenoids (95-437 mg/100 g of dry matter), which were partially bioaccessible. The amount released from the food matrix by the action of digestive enzymes was about 75% for total polyphenols, up to 49% for both beta-carotene and zeaxanthin, and up to 41% for beta-cryptoxanthin. The results suggest that from 50 to 80% of these carotenoids could reach the colon to be potentially fermented or could remain unavailable.

Cooking without salt

MedlinePlus

... onion and garlic powder. Try different types of pepper, including black, white, green, and red. Experiment with ... and spice, try: Dry mustard Fresh chopped hot peppers A sprinkle of paprika, cayenne pepper, or dried ...

Biomimicry as an approach for sustainable architecture case of arid regions with hot and dry climate

NASA Astrophysics Data System (ADS)

Bouabdallah, Nabila; M'sellem, Houda; Alkama, Djamel

2016-07-01

This paper aims to study the problem of thermal comfort inside buildings located in hot and arid climates. The principal idea behind this research is using concepts based on the potential of nature as an instrument that helps creating appropriate facades with the environment "building skin". The biomimetic architecture imitates nature through the study of form, function, behaviour and ecosystems of biological organisms. This research aims to clarify the possibilities that can be offered by biomimicry architecture to develop architectural bio-inspired building's design that can help to enhance indoor thermal ambiance in buildings located in hot and dry climate which helps to achieve thermal comfort for users.

Hot dry rock and the U.S. geological survey: a question of priorities

USGS Publications Warehouse

Sass, John H.

1996-01-01

The enactment of the Energy Policy Act of 1992 saw the assignment of definite responsibilities relating to hot dry rock (HDR) to the US Geological Survey (USGS). This mandate provided some explicit guidelines and individual tasks in areas in which the USGS already had close ties to the Department of Energy and a number of its national laboratories. This paper discusses various tasks in terms of priorities being conducted by USGS as response to the Act.

Consumer Opinion of Emergency/Assault Food Packet under Rigorous Field Conditions in a Cold Weather Environment

DTIC Science & Technology

1980-01-01

and Pudding Bars Although the beverage and pudding bars were designed to be eaten either dry, as packaged, or rehydrated, theoretically with hot water ...pudding bars being rehydrated with hot water and no cases at all of beverage bars being so rehydrated, data will be pre- sented only for the dry and...rehydrated with cold water , is shown in Table 6, which also shows the order in which the beverage and pudding bars were ranked by the survey respondents

Experimentally determined rock-fluid interactions applicable to a natural hot dry rock geothermal system

DOE Office of Scientific and Technical Information (OSTI.GOV)

Charles, R.W.; Holley, C.E. Jr.; Tester, J.W.

1980-02-01

The Los Alamos Scientific Laboratory is pursuing laboratory and field experiments in the development of the Hot Dry Rock concept of geothermal energy. The field program consists of experiments in a hydraulically fractured region of low permeability in which hot rock is intercepted by two wellbores. These experiments are designed to test reservoir engineering parameters such as: heat extraction rates, water loss rates, flow characteristics including impedance and buoyancy, seismic activity and fluid chemistry. Laboratory experiments have been designed to provide information on the mineral reactivity which may be encountered in the field program. Two experimental circulation systems have beenmore » built to study the rates of dissolution and alteration in dynamic flow. Solubility studies have been done in agitated systems. To date, pure minerals, samples of the granodiorite from the actual reservoir and Tijeras Canyon granite have been reacted with distilled water and various solutions of NaCl, NaOH, and Na/sub 2/CO/sub 3/. The results of these experimental systems are compared to observations made in field experiments done in a hot dry rock reservoir at a depth of approximately 3 km with initial rock temperatures of 150 to 200/sup 0/C.« less

Climate Prediction Center: Seasonal Drought Outlook

Science.gov Websites

transitions to summer, however, these dry incipient conditions leave this region vulnerable to flash drought development should an extended period of hot, dry weather occur. Across the West, drought conditions persisted climatology. Despite the anticipated onset of monsoon thunderstorms over the Southwest during mid-summer, dry

Mathematical Modeling of Microwave-Assisted Convective Heating and Drying of Grapes

USDA-ARS?s Scientific Manuscript database

This research studied the processing performance and product quality of Thompson seedless grapes dried using microwave-assisted convective hot air drying as well as the effect of blanching and dipping pretreatments. Two pretreatment methods were compared, dipping into 2% ethyl oleate (V/V) and 5% p...

Silanated Surface Treatment: Effects on the Bond Strength to Lithium Disilicate Glass-Ceramic.

PubMed

Baratto, Samantha Schaffer Pugsley; Spina, Denis Roberto Falcão; Gonzaga, Carla Castiglia; Cunha, Leonardo Fernandes da; Furuse, Adilson Yoshio; Baratto Filho, Flares; Correr, Gisele Maria

2015-10-01

The aim of this study was to evaluate the effect of silanization protocols on the bond strength of two resin cements to a lithium disilicate glass-ceramic. Thirty-two ceramic discs were assigned to 2 groups (n=16): G1 - dual-cured resin cement and G2 - light-cured resin cement. Four subgroups were evaluated according to the used silanization protocol. The glass-ceramic was etched with 10% hydrofluoric acid for 20 s and silane was applied for 1 min, as follows: CTL - according to the manufacturer's instructions; HA - dried with hot air; NWA - washed and dried with water and air at room temperature; HWA - washed and dried with hot water and hot air. Thereafter, adhesive was applied and light-cured for 20 s. Silicon molds were used to prepare resin cement cylinders (1x1 mm) on the ceramic surface. The specimens were stored in deionized water at 37 °C for 48 h and subjected to a micro-shear test. The data were submitted to statistical analysis (?#61537;=0.05). Group G1 showed higher bond strengths than G2, except for the CTL and NWA subgroups. Differences as function of the silanization protocol were only observed in G1: HWA (25.13±6.83)≥HA (22.95±7.78)≥CTL(17.44±7.24) ≥NWA(14.63±8.76). For G2 there was no difference among the subgroups. In conclusion, the silanization protocol affected the resin cement/ceramic bond strengths, depending on the material. Washing/drying with hot water and/or hot air increased only the bond strength of the dual-cured resin cement.

Dynamic control of moisture during hot pressing of wood composites

Treesearch

Cheng Piao; Todd F. Shupe; Chung Y. Hse

2006-01-01

Hot pressing is an important step in the manufacture of wood composites. In the conventional pressing system, hot press output often acts as a constraint to increased production. Severe drying of the furnish (e.g., particles, flakes, or fibers) required by this process substantially increases the manufacturing cost and creates air-polluting emissions of volatile...

High Blood Glucose: What It Means and How To Treat It

MedlinePlus

... your insulin exposed to very hot or cold temperatures? Has your insulin expired? Take the right dose ... strips been exposed to very hot or cold temperatures or not been kept in an airtight, dry, ...

A climate responsive urban design tool: a platform to improve energy efficiency in a dry hot climate

NASA Astrophysics Data System (ADS)

El Dallal, Norhan; Visser, Florentine

2017-09-01

In the Middle East and North Africa (MENA) region, new urban developments should address the climatic conditions to improve outdoor comfort and to reduce the energy consumption of buildings. This article describes a design tool that supports climate responsive design for a dry hot climate. The approach takes the climate as an initiator for the conceptual urban form with a more energy-efficient urban morphology. The methodology relates the different passive strategies suitable for major climate conditions in MENA region (dry-hot) to design parameters that create the urban form. This parametric design approach is the basis for a tool that generates conceptual climate responsive urban forms so as to assist the urban designer early in the design process. Various conceptual scenarios, generated by a computational model, are the results of the proposed platform. A practical application of the approach is conducted on a New Urban Community in Aswan (Egypt), showing the economic feasibility of the resulting urban form and morphology, and the proposed tool.

Development of a microwave clothes dryer

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1993-07-01

The objective of the project is to investigate the microwave drying of clothes and to produce an impartial, generic database for use by interested parties, including appliance manufacturers, who may want to use it when designing and developing microwave clothes dryers. This interim report covers the first year of activity on the project. During that time, a laboratory test model of a microwave clothes dryer was constructed and tested over a wide range of parameters. The test unit was the same size as a residential home dryer and had eight 0.85-kW microwave power supplies from home ovens and a 5-kWmore » resistance air heater. Thus, the model could be used for microwave drying, hot air drying or for a combination of both drying techniques. Microwave drying was effective in three drying modes: Cool drying, fast drying and very efficient drying. Microwaves penetrate the clothes and heat the water molecules directly while conventional heat energy must be conducted through the clothes to evaporate the water. In cool drying, microwaves alone heat the water and an airflow of slightly warmed air carries away the moisture. In fast drying, the microwave power is combined with hot air drying to reduce drying times by as much as 50%. In the most efficient mode of drying, microwave power is used along with the waste heat from the microwave power supply. Hazards testing and fine fabric tests are scheduled for the future.« less

Comparison of different drying methods on the physical properties, bioactive compounds and antioxidant activity of raspberry powders.

PubMed

Si, Xu; Chen, Qinqin; Bi, Jinfeng; Wu, Xinye; Yi, Jianyong; Zhou, Linyan; Li, Zhaolu

2016-04-01

Dehydration has been considered as one of the traditional but most effective techniques for perishable fruits. Raspberry powders obtained after dehydration can be added as ingredients into food formulations such as bakery and dairy products. In this study, raspberry powders obtained by hot air drying (HAD), infrared radiation drying (IRD), hot air and explosion puffing drying (HA-EPD), infrared radiation and microwave vacuum drying (IR-MVD) and freeze drying (FD) were compared on physical properties, bioactive compounds and antioxidant activity. Drying techniques affected the physical properties, bioactive compounds and antioxidant activity of raspberry powders greatly. FD led to significantly higher (P < 0.05) values of water solubility (45.26%), soluble solid (63.46%), hygroscopicity (18.06%), color parameters and anthocyanin retention (60.70%) of raspberry powder compared with other drying methods. However, thermal drying techniques, especially combined drying methods, were superior to FD in final total polyphenol content, total flavonoid content and antioxidant activity. The combined drying methods, especially IR-MVD, showed the highest total polyphenol content (123.22 g GAE kg(-1) dw) and total flavonoid content (0.30 g CAE kg(-1) dw). Additionally, IR-MVD performed better in antioxidant activity retention. Overall, combined drying methods, especially IR-MVD, were found to result in better quality of raspberry powders among the thermal drying techniques. IR-MVD could be recommended for use in the drying industry because of its advantages in time saving and nutrient retention. © 2015 Society of Chemical Industry.

Hot and cold water infusion aroma profiles of Hibiscus sabdariffa: fresh compared with dried.

PubMed

Ramírez-Rodrigues, M M; Balaban, M O; Marshall, M R; Rouseff, R L

2011-03-01

Calyxes from the Roselle plant (Hibiscus sabdariffa L.) were used to prepare cold (22 °C for 4 h) and hot (98 °C for 16 min) infusions/teas from both fresh and dried forms. Aroma volatiles were extracted using static headspace SPME and analyzed using GC-MS and GC-O with 2 different columns (DB-5 and DB-Wax). Totals of 28, 25, 17, and 16 volatiles were identified using GC-MS in the dried hot extract (DHE), dried cold extract (DCE), fresh hot extract (FHE), and fresh cold extract (FCE) samples, respectively. In terms of total GC-MS peak areas DHE ≫ DCE > FHE ≫ FCE. Nonanal, decanal, octanal, and 1-octen-3-ol were among the major volatiles in all 4 beverage types. Thirteen volatiles were common to all 4 teas. Furfural and 5-methyl furfural were detected only in dried hibiscus beverages whereas linalool and 2-ethyl-1-hexanol were detected only in beverages from fresh hibiscus. In terms of aroma active volatiles, 17, 16, 13, and 10 aroma active volatiles were detected for DHE, DCE, FHE, and FCE samples, respectively. The most intense aroma volatiles were 1-octen-3-one and nonanal with a group of 4 aldehydes and 3 ketones common to all samples. Dried samples contained dramatically higher levels of lipid oxidation products such as hexanal, nonanal, and decanal. In fresh hibiscus extracts, linalool (floral, citrus) and octanal (lemon, citrus) were among the highest intensity aroma compounds but linalool was not detected in any of the dried hibiscus extracts. Hibiscus teas/infusions are one of the highest volume specialty botanical products in international commerce. The beverage is consumed for both sensory pleasure and health attributes and is prepared a number of ways throughout the world. Although color and taste attributes have been examined, little information is known about its aroma volatiles and no other study has compared extractions from both fresh and dried as well as extraction temperature differences. This is also, apparently, the first study to identify the aroma active volatiles in hibiscus beverages using GC-olfactometry. Manufacturers and consumers will now have a better understanding of why hibiscus teas prepared in different ways from either fresh or dried forms have a different flavor quality and intensity.

The impact of temperature and precipitation on blacklegged tick activity and Lyme disease incidence in endemic and emerging regions.

PubMed

Burtis, James C; Sullivan, Patrick; Levi, Taal; Oggenfuss, Kelly; Fahey, Timothy J; Ostfeld, Richard S

2016-11-25

The incidence of Lyme disease shows high degrees of inter-annual variation in the northeastern United States, but the factors driving this variation are not well understood. Complicating matters, it is also possible that these driving factors may vary in regions with differing histories of Lyme disease endemism. We evaluated the effect of the number of hot (T > 25 °C), dry (precipitation = 0) days during the questing periods of the two immature Ixodes scapularis life stages (larval and nymphal) on inter-annual variation in Lyme disease incidence between 2000 and 2011 in long-term endemic versus recently endemic areas. We also evaluated the effect of summer weather on tick questing activity and the number of ticks found on small mammals between 1994 and 2012 on six sites in Millbrook, NY. The number of hot, dry days during the larval period of the previous year did not affect the human incidence of Lyme disease or the density of questing nymphs the following season. However, dry summer weather during the nymphal questing period had a significant negative effect on the incidence of Lyme disease in the long-term endemic areas, and on the density of questing nymphs. Summer weather conditions had a more pronounced effect on actively questing I. scapularis collected via dragging than on the number of ticks found feeding on small mammals. In recently endemic areas Lyme disease incidence increased significantly over time, but no trend was detected between disease incidence and dry summer weather. Recently endemic regions showed an increase in Lyme disease incidence over time, while incidence in long-term endemic regions appears to have stabilized. Only within the stabilized areas were we able to detect reduced Lyme disease incidence in years with hot, dry summer weather. These patterns were reflected in our field data, which showed that questing activity of nymphal I. scapularis was reduced by hot, dry summer weather.

Advanced Drying Process for Lower Manufacturing Cost of Electrodes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ahmad, Iftikhar; Zhang, Pu

For this Vehicle Technologies Incubator/Energy Storage R&D topic, Lambda Technologies teamed with Navitas Systems and proposed a new advanced drying process that promised a 5X reduction in electrode drying time and significant reduction in the cost of large format lithium batteries used in PEV's. The operating principle of the proposed process was to use penetrating radiant energy source Variable Frequency Microwaves (VFM), that are selectively absorbed by the polar water or solvent molecules instantly in the entire volume of the electrode. The solvent molecules are thus driven out of the electrode thickness making the process more efficient and much fastermore » than convective drying method. To evaluate the Advanced Drying Process (ADP) a hybrid prototype system utilizing VFM and hot air flow was designed and fabricated. While VFM drives the solvent out of the electrode thickness, the hot air flow exhausts the solvent vapors out of the chamber. The drying results from this prototype were very encouraging. For water based anodes there is a 5X drying advantage (time & length of oven) in using ADP over standard drying system and for the NMP based cathodes the reduction in drying time has 3X benefit. For energy savings the power consumption measurements were performed to ADP prototype and compared with the convection standard drying oven. The data collected demonstrated over 40% saving in power consumption with ADP as compared to the convection drying systems. The energy savings are one of the operational cost benefits possible with ADP. To further speed up the drying process, the ADP prototype was explored as a booster module before the convection oven and for the electrode material being evaluated it was possible to increase the drying speed by a factor of 4, which could not be accomplished with the standard dryer without surface defects and cracks. The instantaneous penetration of microwave in the entire slurry thickness showed a major advantage in rapid drying of the electrode materials. For the existing electrode materials, the material analysis and cell characterization data from ADP dried electrodes showed equivalent (or slightly better) performance. However, for high loading and thicker electrode materials (for high energy densities) the ADP advantages are more prominent. There was less binder migration, the resistance was lower hence the current capacities and retention of the battery cells were higher. The success of the project has enabled credible communications with commercial end users as well as battery coating line integrators. Goal is to scale ADP up for high volume manufacturing of Li-ion battery electrodes. The implementation of ADP in high volume manufacturing will reduce a high cost production step to bring the overall price of Li-ion batteries down. This will ultimately have a positive impact on the public by making electric and hybrid vehicles more affordable.« less

Ssang Yong 2014 Remote Sensing Experiment

DTIC Science & Technology

2016-05-25

determination of the wet field density of soil. Dry density is calculated after the laboratory measurement of the field moisture content...28 Figure 5-9. Drying ovens used in field laboratory established...seasons. Winters are usually long, cold, and dry . Summers are generally short, hot, and humid. Spring and autumn are pleasant but short in duration

The effect of pigment matrix, temperature and amount of carrier on the yield and final color properties of spray dried purple corn (Zea mays L.) cob anthocyanin powders.

PubMed

Lao, Fei; Giusti, M Monica

2017-07-15

Spray drying is an economic technique to produce anthocyanin-based colorants. High pigments yields with minimum color degradation are desirable to maximize quality and profits. This study evaluated the impacts of purple corncob (PCC) anthocyanin extraction matrices (hot water, 40% ethanol, C18 purified), drying inlet temperature (130, 150, 170°C) and amount of carrier (2%, 5%, 10% maltodextrin) on the yields and quality of PCC anthocyanin powders. Monomeric and polymeric anthocyanins, color properties (CIELch, haze), and pigments composition before and after spray drying were determined. The yield and final color quality of spray dried PCC anthocyanins were affected (p<0.05) by all parameters evaluated. The pigment matrix, inlet temperature, and carrier amount had biggest impacts on product water solubility, pigments degradation and yield, respectively. The optimal combination of hot water extracts spray dried with 5% maltodextrin at 150°C gave the highest pigment yield (∼90%) with good solubility with the least color loss. Copyright © 2017 Elsevier Ltd. All rights reserved.

Diurnal thermoregulatory responses in pregnant Yankasa ewes to the dry season in a tropical Savannah.

PubMed

Yaqub, Lukuman Surakat; Ayo, Joseph Olusegun; Kawu, Muhammad Umar; Rekwot, Peter Ibrahim

2017-08-01

The study investigated concomitant effect of gestation and high ambient temperature under a tropical environment on rectal temperature (RT), respiratory rate (RR) and heart rate (HR) responses in Yankasa ewes. Twenty Yankasa ewes, consisting of ten pregnant and ten non-pregnant ewes, were used for the study. Ewes were synchronised and bred, such that each gestation phase coincided with different periods of the dry-seasons, early-gestation (cold/harmattan), mid-gestation (peak hot-dry) and late-gestation (late hot-dry). The RT, RR and HR were recorded thrice, 2 days apart at middle of each gestation period at 06:00, 14:00 and 18:00 h, concurrently with dry- (DBT) and wet-bulb temperatures of the experimental pen. The DBT was positively correlated with RT, RR during the different gestation stages. The RT significantly (P < 0.001) increased with the hour of day, regardless of the physiological status of the ewes, with peak at 14:00 h. Values of RT and RR were higher (P < 0.05) in pregnant than non-pregnant ewes at mid- and late-gestation, respectively. Mean RT was lower (P < 0.001) at 06:00 h in pregnant than non-pregnant ewes at early-gestation (cold-dry). The HR was (P < 0.05) higher in pregnant than non-pregnant ewes during the different gestation phases. In conclusion, ambient temperature and gestation concomitantly modulate diurnal thermoregulatory responses of the ewes to hot-dry season. Adequate measures should be adopted to mitigate adverse impact of prolonged high RR on the dam and the foetus during the peak of ambient temperature prevailing in the tropical Savannah environment.

The Effects of Natural Chinese Medicine Aconite Root, Dried Ginger Rhizome, and Coptis on Rectal and Skin Temperatures at Acupuncture Points

PubMed Central

Li, Gang; Wang, Min; Jin, Yi-Xi; Zhang, Shu-Jing; Wu, Meng-Yao

2017-01-01

The 4 properties of Chinese materia medica refer to cold, hot, warm, and cool. In the present study, the effects of the Coptis, the prepared aconite root, and dried ginger rhizome were compared with regard to the rectal and skin temperature changes of the related body surface acupuncture points (Dazhui, Zhiyang, Mingmen, Zhongwan, and Shenque). The investigation aimed to explore the thermal sensitive points, which can reflect the cold and hot properties of the Chinese herbs. This study showed that the prepared aconite root and dried ginger rhizome exhibited a warming effect on the body temperature, whereas the warming sensitive points were Zhongwan, Shenque, Dazhui, and Zhiyang. Coptis exhibited both a warming and a cooling effect on the body temperature, and the cooling sensitive point was Dazhui. The concomitant effect of these three Chinese herbs on the regulation of the body temperature was reflected by Dazhui. However, there are still some limitations and one-sidedness. For instance, the cold and hot property of some herbs cannot be fully reflected through relevant acupoints on the conception and governor vessels. More detecting sites such as ears and internal organs will be selected for further exploration of Chinese herbs' cold and hot property. PMID:29259648

Dependence of drivers affects risks associated with compound events

NASA Astrophysics Data System (ADS)

Zscheischler, Jakob; Seneviratne, Sonia I.

2017-04-01

Compound climate extremes are receiving increasing attention because of their disproportionate impacts on humans and ecosystems. Risks assessments, however, generally focus on univariate statistics even when multiple stressors are considered. Concurrent extreme droughts and heatwaves have been observed to cause a suite of extreme impacts on natural and human systems alike. For example, they can substantially affect vegetation health, prompting tree mortality, and thereby facilitating insect outbreaks and fires. In addition, hot droughts have the potential to trigger and intensify fires and can cause severe economical damage. By promoting disease spread, extremely hot and dry conditions also strongly affect human health. We analyse the co-occurrence of dry and hot summers and show that these are strongly correlated for many regions, inducing a much higher frequency of concurrent hot and dry summers than what would be assumed from the independent combination of the univariate statistics. Our results demonstrate how the dependence structure between variables affects the occurrence frequency of multivariate extremes. Assessments based on univariate statistics can thus strongly underestimate risks associated with given extremes, if impacts depend on multiple (dependent) variables. We conclude that a multivariate perspective is necessary in order to appropriately assess changes in climate extremes and their impacts, and to design adaptation strategies.

Analysis of extreme summers and prior late winter/spring conditions in central Europe

NASA Astrophysics Data System (ADS)

Träger-Chatterjee, C.; Müller, R. W.; Bendix, J.

2013-05-01

Drought and heat waves during summer in mid-latitudes are a serious threat to human health and agriculture and have negative impacts on the infrastructure, such as problems in energy supply. The appearance of such extreme events is expected to increase with the progress of global warming. A better understanding of the development of extremely hot and dry summers and the identification of possible precursors could help improve existing seasonal forecasts in this regard, and could possibly lead to the development of early warning methods. The development of extremely hot and dry summer seasons in central Europe is attributed to a combined effect of the dominance of anticyclonic weather regimes and soil moisture-atmosphere interactions. The atmospheric circulation largely determines the amount of solar irradiation and the amount of precipitation in an area. These two variables are themselves major factors controlling the soil moisture. Thus, solar irradiation and precipitation are used as proxies to analyse extreme sunny and dry late winter/spring and summer seasons for the period 1958-2011 in Germany and adjacent areas. For this purpose, solar irradiation data from the European Center for Medium Range Weather Forecast 40-yr and interim re-analysis dataset, as well as remote sensing data are used. Precipitation data are taken from the Global Precipitation Climatology Project. To analyse the atmospheric circulation geopotential data at 850 hPa are also taken from the European Center for Medium Range Weather Forecast 40-yr and interim re-analysis datasets. For the years in which extreme summers in terms of high solar irradiation and low precipitation are identified, the previous late winter/spring conditions of solar irradiation and precipitation in Germany and adjacent areas are analysed. Results show that if the El Niño-Southern Oscillation (ENSO) is not very intensely developed, extremely high solar irradiation amounts, together with extremely low precipitation amounts during late winter/spring, might serve as precursor of extremely sunny and dry summer months to be expected.

76 FR 31685 - Endangered and Threatened Wildlife and Plants; Revised Critical Habitat for the Riverside Fairy...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-06-01

... and hot, dry summers), where shallow depressions become seasonally wet or inundated following winter... dry for the remainder of the year. Throughout this proposed revised critical habitat rule, the term... ephemeral wetlands, the wet phase typically occurs between the months of October to May, and the dry phase...

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hoekman, S. Kent; Broch, Broch; Robbins, Curtis

The primary objective of this project was to utilize a flexible, energy-efficient facility, called the DRI Renewable Energy Experimental Facility (REEF) to support various renewable energy research and development (R&D) efforts, along with education and outreach activities. The REEF itself consists of two separate buildings: (1) a 1200-ft2 off-grid capable house and (2) a 600-ft2 workshop/garage to support larger-scale experimental work. Numerous enhancements were made to DRI's existing renewable power generation systems, and several additional components were incorporated to support operation of the REEF House. The power demands of this house are satisfied by integrating and controlling PV arrays, solarmore » thermal systems, wind turbines, an electrolyzer for renewable hydrogen production, a gaseous-fuel internal combustion engine/generator set, and other components. Cooling needs of the REEF House are satisfied by an absorption chiller, driven by solar thermal collectors. The REEF Workshop includes a unique, solar air collector system that is integrated into the roof structure. This system provides space heating inside the Workshop, as well as a hot water supply. The Workshop houses a custom-designed process development unit (PDU) that is used to convert woody biomass into a friable, hydrophobic char that has physical and chemical properties similar to low grade coal. Besides providing sufficient space for operation of this PDU, the REEF Workshop supplies hot water that is used in the biomass treatment process. The DRI-REEF serves as a working laboratory for evaluating and optimizing the performance of renewable energy components within an integrated, residential-like setting. The modular nature of the system allows for exploring alternative configurations and control strategies. This experimental test bed is also highly valuable as an education and outreach tool both in providing an infrastructure for student research projects, and in highlighting renewable energy features to the public.« less

Preparation and combustion of coal-water fuel from the Sin Pun coal deposit, southern Thailand

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

In response to an inquiry by the Department of Mineral Resources in Thailand, the Energy & Environmental Research Center (EERC) prepared a program to assess the responsiveness of Sin Pun lignite to the temperature and pressure conditions of hot-water drying. The results indicate that drying made several improvements in the coal, notably increases in heating value and carbon content and reductions in equilibrium moisture and oxygen content. The equilibrium moisture content decreased from 27 wt% for the raw coal to about 15 wt% for the hot-water-dried (HWD) coals. The energy density for a pumpable coal-water fuel (CWF) indicates an increasemore » from 4500 to 6100 Btu/lb by hot-water drying. Approximately 650 lb of HWD Sin Pun CWF were fired in the EERC`s combustion test facility. The fuel burned extremely well, with no feed problems noted during the course of the test. Fouling and slagging deposits each indicated a very low rate of ash deposition, with only a dusty layer formed on the cooled metal surfaces. The combustor was operated at between 20% and 25% excess air, resulting in a flue gas SO{sub 2} concentration averaging approximately 6500 parts per million.« less

Diets of hartebeest and roan antelope in Burkina Faso: Support of the long-faced hypothesis

USGS Publications Warehouse

Schuette, J.R.; Leslie, David M.; Lochmiller, R.L.; Jenks, J.A.

1998-01-01

Diets of hartebeest (Alcelaphus buselaphus) and roan antelope (Hippotragus equinus) were assessed at the Nazinga Game Ranch in southern Burkina Faso, West Africa. Microhistological analysis of feces indicated that dietary overlap was high during the rainy (X?? = 73.7%) and cool-dry (68.2%) seasons, low during the hot-dry season (48.2%), and lowest during the last month of the hot-dry season (31.5%). As the hot-dry season progressed and food presumably became less available, diets of the two antelopes diverged. Hartebeest maintained a high percentage of grass in their diet, but roan antelope switched from being predominantly grazers (>95% grass) to mixed feeders (<50% grass). As grass feeders, both antelopes have skeletal features that facilitate acquisition and grinding of highly fibrous diets, but 11 of 12 mass-relative indices of the skull morphology of hartebeest exceeded those of roan antelope. Because of those differences in skull morphology, and in keeping with the "long-faced" hypothesis, hartebeest were apparently more capable than roan antelope of acquiring and masticating scarce regrowth of perennial grasses when availability of forage was lowest. Such divergence within a single foraging class of African bovids, such as grass feeders, should reduce competition and perpetuate coexistence.

Temporal Variation Analysis on Climate of Dry-Hot Valley Since 1950s in Upper Yangtze River Basin, China

NASA Astrophysics Data System (ADS)

Sun, L.; Cai, Y.

2017-12-01

Climate of dry-hot valley areas regarding their long term temporal changes are seldom studied. In this paper, climate change in lower reach of Yalongjiang River, a typical dry-hot valley area locating in upper Yangtze River Basin, was analyzed. Ten single meteorological factors were used to investigate basic climatic characteristics, and two integrated index (i.e. relative evapotranspiration(AET/P), standard precipitation evapotranspiration index(SPEI)) were selected to reflect changes from human activities and gauge climate drought regime. Mann-Kendall mutation test was applied to identify mutation year, and variation trends were diagnosed with linear regression and distance average analysis. Mean values were tested to find if there were significant changes resulting from a large artificial reservoir constructed in 1999. Results of mutation test showed that minimum temperature, relative humidity, and AET/P in two stations changed significantly in 2000s. Temperature increased since 1990s, and other single index fluctuated in recent 50 years. Precipitation decreased and temperature increased in autumn significantly, while precipitation in summer decreased slightly. The variation of SPEI implied that the area was humid from 1980s to 2000s, but drought in 2010s. The results of mean test indicated that 56% meteorological index changed significantly, which might be related to the construction of the large reservoir. This research not only reveals the climate change in a dry-hot valley, but also helps study concerning human activities especially the construction of cascade reservoirs in the future in this area.

The response of contrasting tomato genotypes to combined heat and drought stress.

PubMed

Nankishore, Alliea; Farrell, Aidan D

2016-09-01

Efforts to maximize yields of food crops can be undermined by abiotic stress factors, particularly those related to climate change. Here, we use a range of physiological methods to detect the individual and combined effects of heat and drought stress on three contrasting varieties of tomato: Hybrid 61, Moskvich, and Nagcarlang. Seedlings were acclimated under the following treatment regimes: CONTROL (25-36°C; well-watered), DRY (25-36°C; 20% field capacity), HOT (25-42°C; well-watered) and HOT+DRY (25-42°C; 20% field capacity). In each treatment, stomatal conductance, leaf temperature, chlorophyll content, and several chlorophyll fluorescence variables (both in situ and in vitro following a heat shock treatment) were measured. Plants from the HOT treatment remained statistically similar to the CONTROL plants in most of the measured parameters, while those from the DRY treatment and especially the HOT+DRY treatment showed clear effects of abiotic stress. Hybrid 61 showed considerable resilience to heat and drought stress compared to the other varieties, with significantly cooler leaves (one day after treatments imposed) and significantly higher Fv/Fm values both in situ and in vitro. The genotypic differences in resilience to heat stress were only apparent under water-limited conditions, highlighting the need to consider leaf temperature rather than air temperature when testing for tolerance to heat stress. The most effective parameters for discriminating genotypic variation in heat and drought stress were in vitro Fv/Fm and chlorophyll content. Copyright © 2016 Elsevier GmbH. All rights reserved.

The characteristics of geothermal field of Qiabuqia town in Gonghe basin, northeastern Tibetan Plateau

NASA Astrophysics Data System (ADS)

Zhang, C.; Shi, Y.; Jiang, G.

2017-12-01

Located in the northeastern margin of Gonghe basin, Qiabuqia town displays the most potential of hot dry rock geothermal resources exploration and development in China so far. Although large quantities of geophysical exploration work have been down since 2013, the study of present geothermal field is almost empty, which is seriously restricting the evaluation and utilization of geothermal resources in Qiabuqia town. This study is to revel the geothermal characteristics of four hot dry rock boreholes (DR4, DR3, GR1 and GR2) though continuous steady temperature logging and thermal conductivity measurements of core samples. The main stratum of study area are Indosinian granitic rocks (below 1400 m) which is overlain by thick Paleogene, Neogene and Quaternary lacustrine strata (0 1400 m). Continuous temperature logs display that the bottom hole temperature of DR3 borehole is up to 180 oC at the depth of 3000 m and it is the first successfully verification of the existence of hot dry rock geothermal resources in China. The temperature gradients of these for boreholes are obtained by the linear least squares regression method and it turns out that the temperature gradient varies from 38 to 45.2 oC • km-1 with an average of 40.4 oC • km-1. Average thermal conductivity of bedrocks ranges from 2.07 to 3.10 W/(m • K) with an mean of 2.52 W/(m • K). Heat flow values are calculated as the product of least-square thermal gradients and corresponding thermal conductivity. By the result of the calculation, the heat flow are 98.9 mW • m-2, 114.7 mW • m-2, 96.2 mW • m-2, 97.8 mW • m-2 for DR4, DR3, GR1 and GR2 borehole, respectively. Compared to the adjacent Qaidam basin, Sichuan basin and Ordos basin, the study area appear to be a thermal abnormal area with high temperature gradient and high heat flow.

Drying characteristics of garlic ( Allium sativum L) slices in a convective hot air dryer

NASA Astrophysics Data System (ADS)

Demiray, Engin; Tulek, Yahya

2014-06-01

The effects of drying temperatures on the drying kinetics of garlic slices were investigated using a cabinet-type dryer. The experimental drying data were fitted best to the Page and Modified Page models apart from other theoretical models to predict the drying kinetics. The effective moisture diffusivities varied from 4.214 × 10-10 to 2.221 × 10-10 m2 s-1 over the temperature range studied, and activation energy was 30.582 kJ mol-1.

Shelf-life of infrared dry-roasted almonds

USDA-ARS?s Scientific Manuscript database

Infrared heating was recently used to develop a more efficient roasting technology than traditional hot air roasting. Therefore, in this study, we evaluated the shelf-life of almonds roasted with three different approaches, namely infrared [IR], sequential infrared and hot air [SIRHA], and regular h...

7 CFR 58.127 - Facilities.

Code of Federal Regulations, 2012 CFR

2012-01-01

... both hot and cold water of safe and sanitary quality, with adequate facilities for its proper.... Convenient hand-washing facilities shall be provided, including hot and cold running water, soap or other... regularly and the containers cleaned before reuse. Accumulation of dry waste paper and cardboard shall be...

7 CFR 58.127 - Facilities.

Code of Federal Regulations, 2014 CFR

2014-01-01

... both hot and cold water of safe and sanitary quality, with adequate facilities for its proper.... Convenient hand-washing facilities shall be provided, including hot and cold running water, soap or other... regularly and the containers cleaned before reuse. Accumulation of dry waste paper and cardboard shall be...

7 CFR 58.127 - Facilities.

Code of Federal Regulations, 2013 CFR

2013-01-01

... both hot and cold water of safe and sanitary quality, with adequate facilities for its proper.... Convenient hand-washing facilities shall be provided, including hot and cold running water, soap or other... regularly and the containers cleaned before reuse. Accumulation of dry waste paper and cardboard shall be...

7 CFR 58.127 - Facilities.

Code of Federal Regulations, 2011 CFR

2011-01-01

... both hot and cold water of safe and sanitary quality, with adequate facilities for its proper.... Convenient hand-washing facilities shall be provided, including hot and cold running water, soap or other... regularly and the containers cleaned before reuse. Accumulation of dry waste paper and cardboard shall be...

Solar-powered hot-air system

NASA Technical Reports Server (NTRS)

1979-01-01

Solar-powered air heater supplies part or all of space heating requirements of residential or commercial buildings and is interfaced with air to water heat exchanger to heat domestic hot water. System has potential application in drying agricultural products such as cotton, lumber, corn, grains, and peanuts.

High-Performance Computing Data Center Water Usage Efficiency |

Science.gov Websites

cooler-an advanced dry cooler that uses refrigerant in a passive cycle to dissipate heat-was installed at efficiency-using wet cooling when it's hot and dry cooling when it's not. Learn more about NREL's partnership

Infrared Drying as a Quick Preparation Method for Dried Tangerine Peel

PubMed Central

Xu, Mingyue; Zhao, Chengying; Ahmad, Aftab; Zhang, Huijuan; Xiao, Hang

2017-01-01

To establish the most convenient and effective method to dry tangerine peels, different methods (sun drying, hot-air drying, freeze drying, vacuum drying, and medium- and short-wave infrared drying) were exploited. Our results indicated that medium- and short-wave infrared drying was the best method to preserve nutraceutical components; for example, vitamin C was raised to 6.77 mg/g (D.W.) from 3.39 mg/g (sun drying). Moreover, the drying time can be shortened above 96% compared with sun drying. Importantly, the efficiency of DPPH radical scavenging was enhanced from 26.66% to 55.92%. These findings would provide a reliable and time-saving methodology to produce high-quality dried tangerine peels. PMID:29348752

Mercury in water and biomass of microbial communities in hot springs of Yellowstone National Park, USA

USGS Publications Warehouse

King, S.A.; Behnke, S.; Slack, K.; Krabbenhoft, D.P.; Nordstrom, D. Kirk; Burr, M.D.; Striegl, Robert G.

2006-01-01

Ultra-clean sampling methods and approaches typically used in pristine environments were applied to quantify concentrations of Hg species in water and microbial biomass from hot springs of Yellowstone National Park, features that are geologically enriched with Hg. Microbial populations of chemically-diverse hot springs were also characterized using modern methods in molecular biology as the initial step toward ongoing work linking Hg speciation with microbial processes. Molecular methods (amplification of environmental DNA using 16S rDNA primers, cloning, denatured gradient gel electrophoresis (DGGE) screening of clone libraries, and sequencing of representative clones) were used to examine the dominant members of microbial communities in hot springs. Total Hg (THg), monomethylated Hg (MeHg), pH, temperature, and other parameters influential to Hg speciation and microbial ecology are reported for hot springs water and associated microbial mats. Several hot springs indicate the presence of MeHg in microbial mats with concentrations ranging from 1 to 10 ng g-1 (dry weight). Concentrations of THg in mats ranged from 4.9 to 120,000 ng g-1 (dry weight). Combined data from surveys of geothermal water, lakes, and streams show that aqueous THg concentrations range from l to 600 ng L-1. Species and concentrations of THg in mats and water vary significantly between hot springs, as do the microorganisms found at each site. ?? 2006.

Inactivation of Salmonella on pecan nutmeats by hot air treatment and oil roasting.

PubMed

Beuchat, Larry R; Mann, David A

2011-09-01

Studies were done to determine the effectiveness of hot air drying, dry roasting, and oil roasting in killing Salmonella on pecan nutmeats. Pecan halves and pieces were inoculated by immersion in a five-serotype suspension of Salmonella or by surface application of powdered chalk containing the pathogen. Hot air treatment of low-moisture (2.8 to 4.1%) and high-moisture (10.5 to 11.2%) immersion-inoculated nutmeats (initial population, 6.18 to 7.16 log CFU/g) at 120°C for 20 min reduced the number of Salmonella by 1.18 to 1.26 and 1.89 to 2.04 log CFU/g, respectively. However, regardless of the moisture content, hot air treatment of pecan halves containing 0.77 log CFU/g at 120°C for 20 min failed to eliminate Salmonella. Reductions were >7 log CFU/g when dry pieces were dry roasted at 160°C for 15 min. Treatment of halves at 140°C for 20 min, 150°C for 15 min, or 170°C for 10 min reduced Salmonella by 5 log CFU/g. The pathogen was slightly more heat resistant in immersion-inoculated nutmeats than on surface-inoculated nutmeats. Exposure of immersion-inoculated pieces to peanut oil at 127°C for 1.5 min or 132°C for 1.0 min reduced the number of Salmonella by 5 log CFU/g. Treatment of halves at 138°C for 2.0 min reduced Salmonella by 5 log CFU/g; treatment at 132°C for 2.5 to 4.0 min did not always achieve this reduction. Hot air treatment cannot be relied upon to reduce Salmonella by 5 log CFU/g of raw pecan nutmeats without changing sensory qualities. Treatment temperatures and times typically used to oil roast nutmeats appear to be sufficient to reduce Salmonella by 5 log CFU/g.

16 CFR 423.8 - Exemptions.

Code of Federal Regulations, 2010 CFR

2010-01-01

... washing and drycleaning procedures can safely be used on a product: (1) Machine washing in hot water; (2) Machine drying at a high setting; (3) Ironing at a hot setting; (4) Bleaching with all commercially... National Archives and Records Administration (NARA). For information on the availability of this material...

16 CFR 423.8 - Exemptions.

Code of Federal Regulations, 2011 CFR

2011-01-01

... washing and drycleaning procedures can safely be used on a product: (1) Machine washing in hot water; (2) Machine drying at a high setting; (3) Ironing at a hot setting; (4) Bleaching with all commercially... National Archives and Records Administration (NARA). For information on the availability of this material...

Hot melt extrusion versus spray drying: hot melt extrusion degrades albendazole.

PubMed

Hengsawas Surasarang, Soraya; Keen, Justin M; Huang, Siyuan; Zhang, Feng; McGinity, James W; Williams, Robert O

2017-05-01

The purpose of this study was to enhance the dissolution properties of albendazole (ABZ) by the use of amorphous solid dispersions. Phase diagrams of ABZ-polymer binary mixtures generated from Flory-Huggins theory were used to assess miscibility and processability. Forced degradation studies showed that ABZ degraded upon exposure to hydrogen peroxide and 1 N NaOH at 80 °C for 5 min, and the degradants were albendazole sulfoxide (ABZSX), and ABZ impurity A, respectively. ABZ was chemically stable following exposure to 1 N HCl at 80 °C for one hour. Thermal degradation profiles show that ABZ, with and without Kollidon ® VA 64, degraded at 180 °C and 140 °C, respectively, which indicated that ABZ could likely be processed by thermal processing. Following hot melt extrusion, ABZ degraded up to 97.4%, while the amorphous ABZ solid dispersion was successfully prepared by spray drying. Spray-dried ABZ formulations using various types of acids (methanesulfonic acid, sulfuric acid and hydrochloric acid) and polymers (Kollidon ® VA 64, Soluplus ® and Eudragit ® E PO) were studied. The spray-dried ABZ with methanesulfonic acid and Kollidon ® VA 64 substantially improved non-sink dissolution in acidic media as compared to bulk ABZ (8-fold), physical mixture of ABZ:Kollidon ® VA 64 (5.6-fold) and ABZ mesylate salt (1.6-fold). No degradation was observed in the spray-dried product for up to six months and less than 5% after one-year storage. In conclusion, amorphous ABZ solid dispersions in combination with an acid and polymer can be prepared by spray drying to enhance dissolution and shelf-stability, whereas those made by melt extrusion are degraded.

Environmental and functional benefits and trade-offs of hot in-place recycling treatment techniques : final project report.

DOT National Transportation Integrated Search

2016-12-01

Surface recycling is suitable for pavements with minor cracks limited to 25-50 mm in depth. Hot-in-place recycling (HIR) process includes drying and heating the upper layers, scarifying the soft asphalt, mixing the scarified material with a rejuvenat...

Measure Guideline: Ventilation Cooling

DOE Office of Scientific and Technical Information (OSTI.GOV)

Springer, D.; Dakin, B.; German, A.

2012-04-01

The purpose of this measure guideline is to provide information on a cost-effective solution for reducing cooling system energy and demand in homes located in hot-dry and cold-dry climates. This guideline provides a prescriptive approach that outlines qualification criteria, selection considerations, and design and installation procedures.

Effect of high-humidity hot air impingement blanching (HHAIB) on drying and quality of red pepper (Capsicum annuum L.).

PubMed

Wang, Jun; Fang, Xiao-Ming; Mujumdar, A S; Qian, Jing-Ya; Zhang, Qian; Yang, Xu-Hai; Liu, Yan-Hong; Gao, Zhen-Jiang; Xiao, Hong-Wei

2017-04-01

Effects of high-humidity hot air impingement blanching (HHAIB) under different times (30, 60, 90, 120, 150, 180, 210, and 240s) on drying characteristics and quality attributes of red peppers in terms of surface colour, red pigment content, microstructure and texture were investigated. Results showed that polyphenol oxidase (PPO) residual activity of the samples decreased with increasing blanching time; it was decreased to 7% after 120s. A first-order fraction model described PPO inactivation well. Suitable HHAIB time can reduce drying time extensively. Pepper surface colour was influenced by different treatments. In terms of red pigment content, there was no significant difference for blanching time under 120s, whereas over blanching (blanching time ⩾150s) can significantly reduce the red pigment content. Microstructure observations indicate that superficial micro-cracks occur, which explain, why HHAIB enhances drying rate. The firmness, hardness, and gumminess of the samples decreased with increase of HHAIB time. Copyright © 2016 Elsevier Ltd. All rights reserved.

Habitat-specific population structure in native western flower thrips Frankliniella occidentalis (Insecta, Thysanoptera).

PubMed

Brunner, P C; Frey, J E

2010-04-01

Invasions by pest organisms are among the main challenges for sustainable crop protection. They pose a serious threat to crop production by introducing a highly unpredictable element to existing crop protection strategies. The western flower thrips Frankliniella occidentalis (Insecta, Thysanoptera) managed to invade ornamental greenhouses worldwide within < 25 years. To shed light on possible genetic and/or ecological factors that may have been responsible for this invasion success, we studied the population genetic structure of western flower thrips in its native range in western North America. Analysis of nucleotide sequence variation and variation at microsatellite loci revealed the existence of two habitat-specific phylogenetic lineages (ecotypes) with allopatric distribution. One lineage is associated with hot/dry climates, the second lineage is restricted to cool/moist climates. We speculate that the ecological niche segregation found in this study may be among the key factors determining the invasion potential of western flower thrips.

Small-scale lumber drying using wood gasification as a heat source

Treesearch

Richard Bergman

2005-01-01

Small, rural forested communities have the economic need to develop a wood products industry to replace the loss of large sawmills and maintain forest health. The main objective of this study was to explore the potential of using producer (wood) gas to fire a hot water boiler for a small dry kiln capable of drying both softwood and hardwood lumber. A BioMax wood...

Intensification of heat transfer during mild thermal treatment of dry-cured ham by using airborne ultrasound.

PubMed

Contreras, M; Benedito, J; Bon, J; Garcia-Perez, J V

2018-03-01

The application of power ultrasound (PuS) could be used as a novel technology with which to intensify thermal treatments using hot air. Mild thermal treatments have been applied to improve the soft texture of dry-cured ham caused by defective processing. In this regard, the aim of this study was to assess the kinetic intensification linked to the application of airborne PuS in the mild thermal treatment using hot air of dry-cured ham. For this purpose, vacuum packed cylindrical samples (2.52±0.11cm in diameter and 1.90±0.14cm in height) of dry-cured ham were heated using hot air at different temperatures (40, 45, 50°C) and air velocities (1, 2, 3, 4, 6m/s) with (22.3kHz, 50W) and without PuS application. Heat transfer was analyzed by considering that it was entirely controlled by conduction and the apparent thermal diffusivity was identified by fitting the model to the heating kinetics. The obtained results revealed that PuS application sped up the heat transfer, showing an increase in the apparent thermal diffusivity (up to 37%). The improvement in the apparent thermal diffusivity produced by PuS application was greater at high temperatures (50°C) but negligible at high air velocities (6m/s). Heating caused an increase in the hardness and elasticity of dry-cured ham, which would correct ham pastiness defects, while the influence of PuS on such textural parameters was negligible. Copyright © 2017 Elsevier B.V. All rights reserved.

Innovative 'Artificial Mussels' technology for assessing spatial and temporal distribution of metals in Goulburn-Murray catchments waterways, Victoria, Australia: effects of climate variability (dry vs. wet years).

PubMed

Kibria, Golam; Lau, T C; Wu, Rudolf

2012-12-01

The "Artificial mussel" (AM), a novel passive sampling technology, was used for the first time in Australia in freshwater to monitor and assess the risk of trace metals (Cd, Cu, Hg, Pb, and Zn). AMs were deployed at 10 sites within the Goulburn-Murray Water catchments, Victoria, Australia during a dry year (2009-2010) and a wet year (2010-2011). Our results showed that the AMs accumulated all the five metals. Cd, Pb, Hg were detected during the wet year but below detection limits during the dry year. At some sites close to orchards, vine yards and farming areas, elevated levels of Cu were clearly evident during the dry year, while elevated levels of Zn were found during the wet year; the Cu indicates localized inputs from the agricultural application of copper fungicide. The impacts from old mines were significantly less compared 'hot spots'. Our study demonstrated that climate variability (dry, wet years) can influence the metal inputs to waterways via different transport pathways. Using the AMs, we were able to identify various 'hot spots' of heavy metals, which may pose a potential risk to aquatic ecosystems (sub-lethal effects to fish) and public (via food chain metal bioaccumulation and biomagnification) in the Goulburn-Murray Water catchments. The State Protection Policy exempted artificial channels and drains from protection of beneficial use (including protection of aquatic ecosystems) and majority of sites ('hot spots') were located within artificial irrigation channels. Copyright © 2012 Elsevier Ltd. All rights reserved.

Behavioral and hematological responses of broiler chickens administered with betaine and ascorbic acid during hot-dry season.

PubMed

Egbuniwe, Ifeanyichukwu C; Ayo, Joseph O; Kawu, Mohammed U; Mohammed, Aliyu

2018-02-05

Heat stress is a major problem in poultry production in tropical regions. Assessing the impact of thermally stressful environmental conditions on the welfare of broiler chickens is of great importance. Behavioral responses in a novel environment and hematology of broiler chickens administered with betaine and/or ascorbic acid (AA) during the hot-dry season were evaluated. Broiler chickens were randomly divided into four groups: Group I (control) was given sterile water, Group II was given betaine, Group III was given AA, and Group IV received betaine + AA orally and daily for 42 days. An open-field test was used to assess behavior. Hematological parameters were obtained using a hematology auto-analyzer. The natural environmental conditions were predominantly outside the thermoneutral zone for broiler chickens. Results demonstrated that treated groups exhibited improved ability to adjust faster to a new environment and better hematological responses than controls, evidenced by enhanced behavioral responses, oxygen-carrying capacity, and immune responses of broiler chickens under unfavorable environmental conditions. Betaine and/or AA administration to broiler chickens improved some behavioral responses, hemoglobin concentrations, packed cell volume, and total leukocyte count during the hot-dry season.

A comparison of dynamic mechanical properties of processing-tomato peel as affected by hot lye and infrared radiation heating for peeling

USDA-ARS?s Scientific Manuscript database

This study investigated the viscoelastic characteristics of tomato skins subjected to conventional hot lye peeling and emerging infrared-dry peeling by using dynamic mechanical analysis (DMA). Three DMA testing modes, including temperature ramp, frequency sweep, and creep behavior test, were conduct...

Measure Guideline: Ventilation Cooling

DOE Office of Scientific and Technical Information (OSTI.GOV)

Springer, D.; Dakin, B.; German, A.

2012-04-01

The purpose of this measure guideline on ventilation cooling is to provide information on a cost-effective solution for reducing cooling system energy and demand in homes located in hot-dry and cold-dry climates. This guideline provides a prescriptive approach that outlines qualification criteria, selection considerations, and design and installation procedures.

Texture attributes of a persimmon (Diospyros kaki) chip-style product

USDA-ARS?s Scientific Manuscript database

Asian persimmons (Diospyros kaki) are tree fruits that have not yet been widely commercialized into value-added products. A dried, chip-style product (analogous to banana chips) has been developed for persimmons, and the objectives of this work were to characterize the texture of hot-air dried persi...

Thermodynamics between RAP/RAS and virgin aggregates during asphalt concrete production : a literature review.

DOT National Transportation Integrated Search

2015-09-01

In hot-mix asphalt (HMA) plants, virgin aggregates are heated and dried separately before being mixed with : RAP/RAS and virgin asphalt binder. RAP/RAS materials are not heated or dried directly by a burner to avoid : burning of aged binder coating o...

Swift snowmelt and floods (lahars) caused by great pyroclastic surge at Mount St Helens volcano, Washington, 18 May 1980

USGS Publications Warehouse

Waitt, R.B.

1989-01-01

The initial explosions at Mount St. Helens, Washington, on the moring of 18 May 1980 developed into a huge pyroclastic surge that generated catastrophic floods off the east and west flanks of the volcano. Near-source surge deposits on the east and west were lithic, sorted, lacking in accretionary lapilli and vesiculated ash, not plastered against upright obstacles, and hot enough to char wood - all attributes of dry pyroclastic surge. Material deposited at the surge base on steep slopes near the volcano transformed into high-concentration lithic pyroclastic flows whose deposits contain charred wood and other features indicating that these flows were hot and dry. Stratigraphy shows that even the tail of the surge had passed the east and west volcano flanks before the geomorphically distinct floods (lahars) arrived. This field evidence undermines hypotheses that the turbulent surge was itself wet and that its heavy components segregated out to transform directly into lahars. Nor is there evidence that meters-thick snow-slab avalanches intimately mixed with the surge to form the floods. The floods must have instead originated by swift snowmelt at the base of a hot and relatively dry turbulent surge. Impacting hot pyroclasts probably transferred downslope momentum to the snow surface and churned snow grains into the surge base. Melting snow and accumulating hot surge debris may have moved initially as thousands of small thin slushflows. As these flows removed the surface snow and pyroclasts, newly uncovered snow was partly melted by the turbulent surge base; this and accumulating hot surge debris in turn began flowing, a self-sustaining process feeding the initial flows. The flows thus grew swiftly over tens of seconds and united downslope into great slushy ejecta-laden sheetfloods. Gravity accelerated the floods to more than 100 km/h as they swept down and off the volcano flanks while the snow component melted to form great debris-rich floods (lahars) channeled into valleys. ?? 1989 Springer-Verlag.

Stripping in hot mix asphalt produced by aggregates from construction and demolition waste.

PubMed

Pérez, I; Pasandín, A R; Gallego, J

2012-01-01

This paper analyses the effect of water on the durability of hot asphalt mixtures made with recycled aggregates from construction and demolition debris. Indirect tensile stress tests were carried out to evaluate stripping behaviour. The mixtures tested were fabricated with 0, 20, 40 and 60% recycled aggregates. Two types of natural aggregates were used: schist and calcite dolomite. An increase in the percentage of recycled aggregates was found to produce a decrease in the tensile stress ratio of the hot asphalt mixtures. To study this phenomenon, two and three factor analyses of variance (ANOVA) were performed with indirect tensile stress being used as the dependent variable. The factors studied were the percentage of recycled aggregates (0, 20, 40 and 60%), the moisture state (dry, wet) and the type of natural aggregate (schist, calcite). On the basis of the ANOVA results, it was found that the most important factor affecting resistance was the moisture state (dry, wet) of the specimens. The percentage of recycled aggregate also affected indirect tensile stress, especially in the dry state. The type of natural aggregate did not have a significant effect on indirect tensile stress. The hot asphalt mixture specimens made with different percentages of recycled aggregates from construction and demolition debris and of natural quarry aggregates showed poor stripping behaviour. This stripping behaviour can be related to both the poor adhesion of the recycled aggregates and the high absorption of the mortar of cement adhered to them.

Strategies for Tailoring the Pore-Size Distribution of Virus Retention Filter Papers.

PubMed

Gustafsson, Simon; Mihranyan, Albert

2016-06-08

The goal of this work is to demonstrate how the pore-size distribution of the nanocellulose-based virus-retentive filter can be tailored. The filter paper was produced using cellulose nanofibers derived from Cladophora sp. green algae using the hot-press drying at varying drying temperatures. The produced filters were characterized using scanning electron microscopy, atomic force microscopy, and N2 gas sorption analysis. Further, hydraulic permeability and retention efficiency toward surrogate 20 nm model particles (fluorescent carboxylate-modified polystyrene spheres) were assessed. It was shown that by controlling the rate of water evaporation during hot-press drying the pore-size distribution can be precisely tailored in the region between 10 and 25 nm. The mechanism of pore formation and critical parameters are discussed in detail. The results are highly valuable for development of advanced separation media, especially for virus-retentive size-exclusion filtration.

Production of dried shrimp mixed with turmeric and salt by Spouted Bed technique enter the rectangular chamber.

NASA Astrophysics Data System (ADS)

Thanthong, P.; Mustafa, Y.; Ngamrungroj, D.

2017-09-01

Today, dried shrimp in the market were refused food colour and drying until shrimp are colourful and tasty. Meanwhile, Community groups, women’s health trying to produce food products come from herbs. As an alternative to consumers. The production process is also a traditional way to dry. In order to extend the shelf life longer. Sometimes, potential risks, both in quality and quantity of products. As a result, consumers are enormous. Thus, this research aims to study the possibility to produce shrimp dried mixed with turmeric and salt. Then dried shrimp mixed with turmeric and salt to keep up the quality criteria of the Food and Drug Administration-FDA It can reduce the risk of the consumer and can keep up in a kitchen Thailand. When buying shrimp from the fisherman’s boat Will be made clear, clean impurities and shaking the sand to dry. Prepare a mixture of turmeric and salt. The shrimp were dipped into a beef with stirrer for 3 minutes. And scoop up centrifugal shrimp with dried. Measurement of initial moisture content averaging 78%wb. Then drying technique Spouted enter the rectangular chamber a continuous manner. Until average moisture content to 17%wb. The air temperature in the drying chamber at 180 °C and hot air speed 4.5 m/s, a state heat transfer Mass and moisture within the shrimp. In chamber when drying, the shrimp have moved freely behaviour can spit water out faster does not burn. Shaving legs of shrimp shell fragments lightweight is sorting out the top of drying chamber. Private shrimp were dried out to the front of the quad drying chamber. Power consumption 27.5 MJ/kg, divided into electrical energy 12.3 MJ/kg and thermal energy is 15.2 MJ/kg. The hot air comes from burning LPG gas burner with dual automatic. And can adjustable to room temperature drying characteristics modulation setting.

Drying kinetics and characteristics of dried gambir leaves using solar heating and silica gel dessicant

NASA Astrophysics Data System (ADS)

Hasibuan, R.; Hidayati, J.; Sundari, R.; Wicaksono, A. S.

2018-02-01

A drying combination of solar heating and silica gel dessicant has been applied to dry gambir leaves. The solar energy is captured by a collector to heat the air and the hot air is used to dry gambir leaves in a drying chamber. An exhaust fan in drying chamber assists to draw water molecules from gambir leaves accelerated by silica gel dessicant. This study has investigated the drying kinetics and drying characteristics of gambir leaves drying. In drying operation the air velocity is tuned by a PWM (pulse width modulation) controller to adjust minimum and maximum level, which is based on the rotation speed of the exhaust fan. The results show that the air velocity influenced the drying kinetics and drying characteristics of gambir leaves using solar-dessicant drying at 40 cm distance between exhaust fan and silica gel dessicant.

Method of Forming a Hot Film Sensor System on a Model

NASA Technical Reports Server (NTRS)

Tran, Sang Q. (Inventor)

1998-01-01

A method of forming a hot film sensor directly on a model is provided. A polyimide solution is sprayed onto the model. The model so sprayed is then heated in air. The steps of spraying and heating are repeated until a polyimide film of desired thickness is achieved on the model. The model with the polyimide film thereon is then thoroughly dried in air. One or more hot film sensors and corresponding electrical conducting leads are then applied directly onto the polyimide film.

The evaporative drying of sludge by immersion in hot oil: Effects of oil type and temperature.

PubMed

Ohm, Tae-In; Chae, Jong-Seong; Lim, Kwang-Soo; Moon, Seung-Hyun

2010-06-15

We investigated the evaporative drying by immersion in hot oil (EDIHO) method for drying sludge. This involved heating oil to a temperature higher than that needed for moisture to be evaporated from the sludge by turbulent heat and mass transfer. We fry-dried sewage and leather plant sludge for 10 min in each of four different oils (waste engine, waste cooking, refined waste, and B-C heavy) and three different temperatures (140 degrees C, 150 degrees C, and 160 degrees C). Drying efficiency was found to be greater for higher temperatures. However, giving consideration to energy efficiency we suggest that the optimal temperature for fry-drying sludge is 150 degrees C. At 150 degrees C, the water content of sewage sludge reduced from 78.9% to between 1.5% (with waste cooking oil) and 3.8% (with waste engine oil). The reduction in water content for leather plant sludge fry-dried at 150 degrees C was from 81.6% to between 1% (with waste cooking oil) and 6.5% (with refined waste oil). The duration of the constant rate-drying period was also influenced by the type of oil used: refined waste oil>waste engine oil>B-C heavy oil>waste cooking oil. The duration at 150 degrees C with waste cooking oil was 3 min for sewage sludge and 2 min for leather plant sludge. It is likely that the drying characteristics of oil are influenced by its thermal properties, including its specific heat, and molecular weight. Copyright 2010 Elsevier B.V. All rights reserved.

Effect of hot densification on tribotechnical properties of sintered (Al-12Si)-40Sn alloy

NASA Astrophysics Data System (ADS)

Rusin, N. M.; Skorentsev, A. L.; Kolubaev, E. A.

2017-12-01

The paper describes the effect of hot densification on mechanical and tribotechnical properties of sintered samples of (Al-12Si)-40Sn composition. It proves that such treatment increases the strength and ductility of the studied materials and makes higher their wear resistant under dry friction against a steel counterbody.

Petrologic considerations for hot dry rock geothermal site selection in the Clear Lake Region, California

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stimac, J.; Goff, F.; Hearn, B.C. Jr.

1992-01-01

The Clear Lake area is well known for anomalous heat flow, thermal springs, hydrothermal mineral deposits, and Quaternary volcanism. These factors, along with the apparent lack of a large reservoir of geothermal fluid north of Collayomi fault make the Clear Lake area an attractive target for hot dry rock (HDR) geothermal development. Petrologic considerations provide some constraints on site selection for HDR development. Spatial and temporal trends in volcanism in the Coast Ranges indicate that magmatism has migrated to the north with time, paralleling passage of the Mendocino triple junction and propagation of the San Andreas fault. Volcanism in themore » region may have resulted from upwelling of hot asthenosphere along the southern margin of the subducted segment of the Gorda plate. Spatial and temporal trends of volcanism within the Clear Lake volcanic field are similar to larger-scale trends of Neogene volcanism in the Cost Ranges. Volcanism (especially for silicic compositions) shows a general migration to the north over the {approximately}2 Ma history of the field, with the youngest two silicic centers located at Mt. Konocti and Borax Lake. The Mt. Konocti system (active from {approximately} 0.6 to 0.3 Ma) was large and long-lived, whereas the Borax Lake system is much smaller but younger (0.09 Ma). Remnants of silicic magma bodies under Mt. Konocti may be in the latter stages of cooling, whereas a magma body centered under Borax Lake may be in the early stages of development. The existence of an upper crustal silicic magma body of under Borax Lake has yet to be demonstrated by passive geophysics, however, subsurface temperatures in the area as high (> 200{degrees}C at 2000 m) as those beneath the Mt. Konocti area. Based on petrologic considerations alone, the Mt. Konocti-Borax Lake area appears to be the most logical choice for HDR geothermal development in the region.« less

Cercarial emergence patterns for Opisthorchis viverrini sensu lato infecting Bithynia siamensis goniomphalos from Sakon Nakhon Province, Thailand.

PubMed

Laoprom, Nonglak; Kiatsopit, Nadda; Sithithaworn, Paiboon; Kopolrat, Kulthida; Namsanor, Jutamas; Andrews, Ross H; Petney, Trevor N

2016-09-01

Opisthorchis viverrini sensu lato is a food-borne trematode which is classified as a class 1 carcinogen, with infection potentially leading to cholangiocarcinoma. Snails of the genus Bithynia act as the first intermediate hosts and an amplifying point in the parasite life cycle. In order to investigate seasonal effect on transmission dynamics of O. viverrini in Bithynia siamensis goniomphalos, cercarial emergence and output profiles were monitored at different season. A total of 4533 snails originating from Sakon Nakhon Province, Thailand, collected during the three main seasons, were analyzed for O. viverrini s.l. Emergence of O. viverrini s.l. cercariae from snails was monitored daily from 06:00 to 18:00 h for seven consecutive days. The prevalence of infection in the snails was highest in the hot-dry season and declined in the rainy and cool-dry seasons. Peak cercarial emergence occurred between 08:00 and 10:00 h during the rainy and cool-dry seasons and between 10:00 and 12:00 h during the hot-dry season. The cercarial output was highest in the hot-dry season, similar to a previous study from Lao People's Democratic Republic (PDR). Average cercarial output/snail in Thailand was higher than in Lao PDR. The number of cercariae emerging from the snails was strongly related to snail size, but the relationship between prevalence of infection and snail size differed between seasons. Observed discrepancies in the emergence patterns and per capita cercarial release may reflect differences in environmental, snail, and/or parasite factors particularly biological characteristics between the cryptic species of O. viverrini s.l. and B. s. goniomphalos from Thailand and Lao PDR.

Milk yield and composition of crossbred Sahelian × Anglo-Nubian goats in the semi-intensive system in Mali during the preweaning period.

PubMed

Sanogo, Souleymane; Shaker, Mohamed Momani; Nantoumé, Hamidou; Salem, Abdel-Fattah Z M

2013-01-01

The aim of this study was to evaluate milk yield and its composition during the preweaning period for Sahelian goats (SG) and Anglo-Nubian (AN) crossbred depending on some factors. The experiments were conducted from January to December 2008 for 44 suckled and hand-milked does, randomized, and divided into two equal groups: SG (n = 22) and F(1) Anglo-Nubian × Sahelian goats (1/2AN; n = 22). The does and their offsprings were kept in a pen where they stayed indoors for 45 days before they were allowed outdoors when the weather was suitable. Each category received supplemental feeds depending on the season (rainy season, dry cold season, and dry hot season). The average daily milk yield was recorded weekly from parturition to 100 days of age. Individual milk samples were taken for chemical analysis in connection with the yield measurements twice per month from the fourth week of lactation throughout the different seasons (rainy, cold dry, and hot dry). The daily milk yield differed between breed types (P = 0.001) during the preweaning, while the effect of kids' sex on daily milk production was not significant. Litter size affected milk yield up to day 60 (P = 0.032) where does with twins producing more milk than those with single kid. However, at day 100, both groups had similar (P = 0.001) milk production. Total milk yield at weaning increased by 103 % in 1/2AN over SG. The highest concentration of total solids of milk was (12.76 %) recorded in the hot dry season. The results of this study indicate that crossbreeding native Sahelian goats with high potential Anglo-Nubian buck improved milk production and its composition.

Nasal variation in relation to high-altitude adaptations among Tibetans and Andeans.

PubMed

Butaric, Lauren N; Klocke, Ross P

2018-05-01

High-altitude (>2500 m) populations face several pressures, including hypoxia and cold-dry air, resulting in greater respiratory demand to obtain more oxygen and condition inspired air. While cardiovascular and pulmonary adaptations to high-altitude hypoxia have been extensively studied, adaptations of upper-respiratory structures, e.g., nasal cavity, remain untested. This study investigates whether nasal morphology presents adaptations to hypoxic (larger noses) and/or cold-dry (tall/narrow noses) conditions among high-altitude samples. CT scans of two high- and four low-altitude samples from diverse climates were collected (n = 130): high-altitude Tibetans and Peruvians; low-altitude Peruvians, Southern Chinese (temperate), Mongolian-Buriats (cold-dry), and Southeast Asians (hot-wet). Facial and nasal distances were calculated from 3D landmarks placed on digitally-modeled crania. Temperature, precipitation, and barometric pressure data were also obtained. Principal components analysis and analyses of variance primarily indicate size-related differences among the cold-dry (Mongolian-Buriats) and hot-wet (Southeast Asians) adapted groups. Two-block partial least squares (PLS) analysis show weak relationships between size-standardized nasal dimensions and environmental variables. However, among PLS1 (85.90% of covariance), Tibetans display relatively larger nasal cavities related to lower temperatures and barometric pressure; regression analyses also indicate high-altitude Tibetans possess relatively larger internal nasal breadths and heights for their facial size. Overall, nasal differences relate to climate among the cold-dry and hot-wet groups. Specific nasal adaptations were not identified among either Peruvian group, perhaps due to their relatively recent migration history and population structure. However, high-altitude Tibetans seem to exhibit a compromise in nasal morphology, serving in increased oxygen uptake, and air-conditioning processes. © 2018 Wiley Periodicals, Inc.

Forced Hot Air to Dry Feces and Kill Bacteria on Transport Cage Flooring

USDA-ARS?s Scientific Manuscript database

Due to fecal shedding from positive birds, broiler transport cages can be contaminated with human bacterial pathogens leading to cross contamination of previously negative broilers during live haul. Earlier work has shown that drying soiled or washed cages for 24 to 48 hours can lower or even elimi...

Patch scale turbulence over dryland and irrigated surfaces in a semi-arid landscape during BEAREX08

USDA-ARS?s Scientific Manuscript database

Quantifying turbulent fluxes of heat and water vapor over heterogeneous surfaces presents unique challenges. For example, in many arid and semi-arid regions, parcels of irrigated cropland are juxtaposed with hot, dry surfaces. Contrasting surface conditions can result in the advection of warm dry ai...

High humidity hot air impingement blanching (HHAIB) enhances drying rate and softens texture of apricot via cell wall pectin polysaccharides degradation and ultrastructure modification.

PubMed

Deng, Li-Zhen; Mujumdar, A S; Yang, Xu-Hai; Wang, Jun; Zhang, Qian; Zheng, Zhi-An; Gao, Zhen-Jiang; Xiao, Hong-Wei

2018-09-30

The effects of high humidity hot air impingement blanching (HHAIB) over a range of application times (30, 60, 90, and 120 s) on drying characteristics, hardness, cell wall pectin fractions contents and nanostructure, as well ultrastructure of apricot were investigated. Results showed that HHAIB reduced drying time and decreased the hardness of apricot by 20.7%-34.5% and 46.57%-71.89%, respectively. The water-soluble pectin (WSP) contents increased after blanching, while the contents of chelate-soluble pectin (CSP) and sodium-carbonate-soluble pectin (NSP) decreased significantly (P < 0.05). The hardness and drying time were found to correlate inversely with the WSP content, but positively with CSP and NSP contents. Atomic force microscopy (AFM) detection showed the decomposition and degradation of pectin fractions during blanching. Additionally, transmission electron microscopy (TEM) observation indicated that the cell wall structure was degraded and middle lamella integrity was destroyed by blanching. Copyright © 2018 Elsevier Ltd. All rights reserved.

Heat and mass transfer within partially wetted packed fractured granular beds

DOE Office of Scientific and Technical Information (OSTI.GOV)

Khalil, E.B.; Karim, G.A.

1996-10-01

Fractured granular beds heated by hot gaseous streams have been the subject of numerous investigations in recent years due to their importance in many applications such as in in-situ and enhanced oil recovery. In a previous paper (Khalil and Karim, 1995) the results of an investigation of some aspects of the transport processes that occur within dry granular beds were reported. The present contribution examines similar beds when partially wetted. The granular beds were cylindrical in shape containing an axial central small diameter circular channel representing a fracture which can have different permeability from that of the main bed. Itmore » is shown that the mass flow rate of the hot gases, the relative permeability of the bed and the central channel as well as the initial liquid content of the bed control the drying rate. The results of an analytical model formulated to simulate the drying process in unobstructed channel beds showed good agreement with experimental results at low temperatures, however deviations occurred as the drying proceeds at higher temperatures.« less

Grain dryer temperature field analysis

NASA Astrophysics Data System (ADS)

Li, Shizhuang; Cao, Shukun; Meng, Wenjing; Ma, Lingran

2017-09-01

Taking into account the drying process in the hot air temperature on the grain temperature has a great impact, and grain temperature and determines the quality of food after baking, so in order to ensure that the grain drying temperature in the safe range, the use of ANSYS FLUENT module of grain The temperature field was simulated in the drying process. The horizontal spacing of the angle box was 200mm and the vertical spacing was 240mm. At this time, the grain temperature distribution was more uniform and the drying was more adequate.

Hot Spots and Hot Moments of Methylmercury Production Associated With Agricultural and Non-agricultural Wetlands of the Yolo Bypass Wildlife Area, California

NASA Astrophysics Data System (ADS)

Marvin-Dipasquale, M.; Windham-Myers, L.; Agee, J. L.; Kakouros, E.; Cox, M. H.; Fleck, J.; Alpers, C. N.; Stephenson, M.

2008-12-01

The Yolo Bypass Wildlife Area (YBWA) is part of the larger Yolo Bypass floodwater protection zone associated with the Sacramento River and the Sacramento-San Joaquin Delta, in California. While mercury contamination is widespread throughout the region due to historic mining practices, the Yolo Bypass is responsible for a high proportion of the aqueous methylmercury (MeHg) entering the Delta, and biota from the Yolo Bypass are particularly elevated in toxic MeHg. Land use in the YBWA includes seasonally flooded agricultural fields (white rice, wild rice, fallow fields), and permanently and seasonally flooded non-agricultural wetlands used for resident and migratory waterfowl. Mercury biogeochemistry was examined in 0-2 cm surface sediment, as a function of habitat type, wetland management, and agricultural practices during the 2007-08 crop year. In permanently flooded wetlands, MeHg concentrations varied within a narrow range (ca. 0.5-1.5 ng/g dry wt) throughout the study period. In contrast, the three types of agricultural fields had higher MeHg concentrations throughout the rice-growing season (June-Sept; ca. 1.5-3.5 ng/g), and exhibited the highest levels (ca. 3.3-6.3 ng/g) in the post-harvest winter period (Dec-Feb). Further, naturally dried sediment, sampled during July '08 from post-harvest drained fallow agricultural fields (prior to reflooding) had MeHg concentrations that were also quite elevated (3.1 +/- 1.5 ng/g). This suggests that the initial elevated concentrations of overlying water MeHg, sometimes measured soon after flooding previously dried fields, may be related to the release of MeHg formed during the previous wet season and trapped in dried sediment, as opposed to being MeHg newly produced by bacteria upon soil rewetting. These results indicate that the 'hot spots and hot moments' associated with MeHg production in this system are linked to hydrologic manipulations (wetting and drying) in the agricultural fields, and that the practice of post-harvest reflooding of rice fields, to promote rice straw decomposition during the fall and winter, may stimulate microbial activity associated with increased MeHg production during that period.

Salt shell fallout during the ash eruption at the Nakadake crater, Aso volcano, Japan: evidence of an underground hydrothermal system surrounding the erupting vent

NASA Astrophysics Data System (ADS)

Shinohara, Hiroshi; Geshi, Nobuo; Yokoo, Akihiko; Ohkura, Takahiro; Terada, Akihiko

2018-03-01

A hot and acid crater lake is located in the Nakadake crater, Aso volcano, Japan. The volume of water in the lake decreases with increasing activity, drying out prior to the magmatic eruptions. Salt-rich materials of various shapes were observed, falling from the volcanic plume during the active periods. In May 2011, salt flakes fell from the gas plume emitted from an intense fumarole when the acid crater lake was almost dry. The chemical composition of these salt flakes was similar to those of the salts formed by the drying of the crater lake waters, suggesting that they originated from the crater lake water. The salt flakes are likely formed by the drying up of the crater lake water droplets sprayed into the plume by the fumarolic gas jet. In late 2014, the crater lake dried completely, followed by the magmatic eruptions with continuous ash eruptions and intermittent Strombolian explosions. Spherical hollow salt shells were observed on several occasions during and shortly after the weak ash eruptions. The chemical composition of the salt shells was similar to the salts formed by the drying of the crater lake water. The hollow structure of the shells suggests that they were formed by the heating of hydrothermal solution droplets suspended by a mixed stream of gas and ash in the plume. The salt shells suggest the existence of a hydrothermal system beneath the crater floor, even during the course of magmatic eruptions. Instability of the magmatic-hydrothermal interface can cause phreatomagmatic explosions, which often occur at the end of the eruptive phase of this volcano.

A review on proniosomal drug delivery system for targeted drug action.

PubMed

Radha, G V; Rani, T Sudha; Sarvani, B

2013-03-01

Proniosomes are dry formulation of water soluble carrier particles that are coated with surfactant. They are rehydrated to form niosomal dispersion immediately before use on agitation in hot aqueous media within minutes. Proniosomes are physically stable during the storage and transport. Drug encapsulated in the vesicular structure of proniosomes prolong the existence of drug in the systematic circulation and enhances the penetration into target tissue and reduce toxicity. From a technical point of view, niosomes are promising drug carriers as they possess greater chemical stability and lack of many disadvantages associated with liposomes, such as high- cost and variable purity problems of phospholipids. The present review emphasizes on overall methods of preparation characterization and applicability of proniosomes in targeted drug action.

[Seasonal variation of soil respiration and its components in tropical rain forest and rubber plantation in Xishuangbanna, Yunnan].

PubMed

Lu, Hua-Zheng; Sha, Li-Qing; Wang, Jun; Hu, Wen-Yan; Wu, Bing-Xia

2009-10-01

By using trenching method and infrared gas analyzer, this paper studied the seasonal variation of soil respiration (SR), including root respiration (RR) and heterotrophic respiration (HR), in tropical seasonal rain forest (RF) and rubber (Hevea brasiliensis) plantation (RP) in Xishuangbanna of Yunnan, China. The results showed that the SR and HR rates were significantly higher in RF than in RP (P < 0.01), while the RR rate had less difference between the two forests. Soil temperature and moisture were the key factors affecting the SR, RR and HR. The SR and HR rates in the two forests were rainy season > dry-hot season > foggy season, but the RR rate was rainy season > foggy season > dry-hot season in RF, and foggy season > rainy season > dry-hot season in RP. The contribution of RR to SR in RF (29%) was much lower than that in RP (42%, P < 0.01), while the contribution of HR to SR was 71% in RF and 58% in RP. When the soil temperature at 5 cm depth varied from 12 degrees C to 32 degrees C, the Q10 values for SR, HR, and RR rates were higher in RF than in RP. HR had the highest Q10 value, while RR had the lowest one.

2-D hydro-viscoelastic model for convective drying of deformable and unsaturated porous material

NASA Astrophysics Data System (ADS)

Hassini, Lamine; Raja, Lamloumi; Lecompte-Nana, Gisèle Laure; Elcafsi, Mohamed Afif

2017-04-01

The aim of this work was to simulate in two dimensions the spatio-temporal evolution of the moisture content, the temperature, the solid (dry matter) concentration, the dry product total porosity, the gas porosity, and the mechanical stress within a deformable and unsaturated product during convective drying. The material under study was an elongated cellulose-clay composite sample with a square section placed in hot air flow. Currently, this innovative composite is used in the processing of boxes devoted to the preservation of heritage and precious objects against fire damage and other degradation (moisture, insects, etc.). A comprehensive and rigorous hydrothermal model had been merged with a dynamic linear viscoelasticity model based on Bishop's effective stress theory, assuming that the stress tensor is the sum of solid, liquid, and gas stresses. The material viscoelastic properties were measured by means of stress relaxation tests for different water contents. The viscoelastic behaviour was described by a generalized Maxwell model whose parameters were correlated to the water content. The equations of our model were solved by means of the 'COMSOL Multiphysics' software. The hydrothermal part of the model was validated by comparison with experimental drying curves obtained in a laboratory hot-air dryer. The simulations of the spatio-temporal distributions of mechanical stress were performed and interpreted in terms of material potential damage. The sample shape was also predicted all over the drying process.

A comparative study of the effect of spray drying and hot-melt extrusion on the properties of amorphous solid dispersions containing felodipine.

PubMed

Mahmah, Osama; Tabbakh, Rami; Kelly, Adrian; Paradkar, Anant

2014-02-01

To compare the properties of solid dispersions of felodipine for oral bioavailability enhancement using two different polymers, polyvinylpyrrolidone (PVP) and hydroxypropyl methylcellulose acetate succinate (HPMCAS), by hot-melt extrusion (HME) and spray drying. Felodipine solid dispersions were prepared by HME and spray drying techniques. PVP and HPMCAS were used as polymer matrices at different drug : polymer ratios (1 : 1, 1 : 2 and 1 : 3). Detailed characterization was performed using differential scanning calorimetry, powder X-ray diffractometry, scanning electron microscopy and in-vitro dissolution testing. Dissolution profiles were evaluated in the presence of sodium dodecyl sulphate. Stability of different solid dispersions was studied under accelerated conditions (40°C/75% RH) over 8 weeks. Spray-dried formulations were found to release felodipine faster than melt extruded formulations for both polymer matrices. Solid dispersions containing HMPCAS exhibited higher drug release rates and better wettability than those produced with a PVP matrix. No significant differences in stability were observed except with HPMCAS at a 1 : 1 ratio, where crystallization was detected in spray-dried formulations. Solid dispersions of felodipine produced by spray drying exhibited more rapid drug release than corresponding melt extruded formulations, although in some cases improved stability was observed for melt extruded formulations. © 2013 Royal Pharmaceutical Society.

Time-of-flight secondary ion mass spectrometry study on the distribution of alendronate sodium in drug-loaded ultra-high molecular weight polyethylene.

PubMed

Liu, Xiaomin; Qu, Shuxin; Lu, Xiong; Ge, Xiang; Leng, Yang

2009-12-01

The aim of this study was to investigate the drug distribution in ultra-high molecular weight polyethylene (UHMWPE) loaded with alendronate sodium (ALN), which was developed to treat particle-induced osteolysis after artificial joint replacements, since the drug distribution in UHMWPE could play a key role in controlling drug release. A mixture of UHMWPE powder and ALN was dried and hot pressed to prepare UHMWPE loaded with ALN (UHMWPE-ALN). Fourier transform infrared spectroscopy analysis demonstrated that the hot press had no effect on the functional groups of ALN in UHMWPE-ALN. X-ray diffraction indicated that there was no phase change of the UHMWPE after hot pressing. Time-of-flight secondary ion mass spectrometry (ToF-SIMS) spectra revealed the existence of characteristic elements and functional groups from ALN in UHMWPE-ALN, such as Na+, C3H8N+, PO3(-) and PO3H(-). In addition, SIMS images suggested that ALN did not agglomerate in UHMWPE-ALN. A small punch test and hardness test were carried out and the results indicated that ALN did not affect the mechanical properties at the present content level. The present study demonstrated that it was feasible to fabricate the un-agglomerated distributed drug in UHMWPE with good mechanical properties. This ALN loaded UHMWPE would have potential application in clinics.

Increasing heat waves and warm spells in India, observed from a multiaspect framework

NASA Astrophysics Data System (ADS)

Panda, Dileep Kumar; AghaKouchak, Amir; Ambast, Sunil Kumar

2017-04-01

Recent heat waves have been a matter of serious concern for India because of potential impacts on agriculture, food security, and socioeconomic progress. This study examines the trends and variability in frequency, duration, and intensity of hot episodes during three time periods (1951-2013, 1981-2013 and 1998-2013) by defining heat waves based on the percentile of maximum, minimum, and mean temperatures. The study also explores heat waves and their relationships with hydroclimatic variables, such as rainfall, terrestrial water storage, Palmer drought severity index, and sea surface temperature. Results reveal that the number, frequency, and duration of daytime heat waves increased considerably during the post-1980 dry and hot phase over a large area. The densely populated and agriculturally dominated northern half of India stands out as a key region where the nighttime heat wave metrics reflected the most pronounced amplifications. Despite the recent warming hiatus in India and other parts of the world, we find that both daytime and nighttime extreme measures have undergone substantial changes during or in the year following a dry year since 2002, with the probability distribution functions manifesting a hotter-than-normal climate during 1998-2013. This study shows that a few months preceding the 2010 record-breaking heat wave in Russia, India experienced the largest hot episode in the country's history. Interestingly, both these mega events are comparable in terms of their evolution and amplification. These findings emphasize the importance of planning for strategies in the context of the rising cooccurrence of dry and hot events.

Nutritional quality and amino acid composition of diets consumed by scavenging hens and cocks across seasons.

PubMed

Ncobela, Cyprial Ndumiso; Chimonyo, Michael

2016-04-01

The objective of the study was to determine the effect of season on nutritional quality and amino acid composition of diets that scavenging hens and cocks consume. Thirty hens and 30 cocks were purchased and slaughtered during each of the rainy, post rainy, cool dry and hot dry seasons. A total of 240 birds were used in the study. Fresh crop content weights were high (P < 0.05) during the cool dry season. Cereal grains, kitchen wastes, green materials, animal protein sources and inorganic materials were the main components of the crop contents. Crop contents varied with season and sex of bird (P < 0.05). The cereal grain weights were high during cool dry and hot dry seasons. Weights of animal protein sources (insects, locusts and termites) were higher (P < 0.05) during the rainy and post rainy seasons. Hens contained more animal protein sources (P < 0.05) than cocks. Hens had a higher (P < 0.05) lysine content during the rainy season than cocks. Histidine, serine, arginine, threonine, cysteine and lysine contents varied with seasons (P < 0.05). Methionine did not vary with season and sex of the bird. Nutritional supplementation of village chickens should, therefore, vary with seasons.

A comparative study on the characteristics of radioactivities and negative air ions originating from the minerals in some radon hot springs.

PubMed

Sakoda, Akihiro; Hanamoto, Katsumi; Haruki, Naoto; Nagamatsu, Tomohiro; Yamaoka, Kiyonori

2007-01-01

To elucidate the characteristics of some radon hot springs, we simulated a hot spring by soaking the rocks for the radon therapy in water and measured the concentrations of radon and negative air ions in various conditions. In the results, the individual rock structure could contribute to radon leaching because the radon leaching rates were independent of the grain sizes. More negative air ions were generated by the wet rocks than by the dry rocks.

Powder processing and mechanical properties of Silver0.86Lead19Antimony telluride20 (LAST) and Lead0.95Tin0.05Tellurium - Lead sulfide 8% (Lead telluride -Lead sulfide) thermoelectric materials

NASA Astrophysics Data System (ADS)

Ni, Jennifer Elisabeth

Thermoelectric (TE) materials convert between thermal and electrical energy and when used with existing processes will increase the efficiency via waste heat recovery. Ag0.86Pb19SbTe20 (LAST) and Pb0.95Sn0.05Te - PbS 8% (PbTe-PbS) materials exhibit good thermoelectric (TE) properties and have potential applications as thermoelectric generators in waste heat recovery. However, to fully characterize the thermo-mechanical behavior of LAST and PbTe-PbS materials under in-service conditions, knowledge is needed of the mechanical and thermal properties at room and high temperature. As fracture strength is inversely proportional to the square root of grain size, cast ingots were powder processed to reduce powder particle size. Three different powder processing methods were used (1) dry milling only, (2) wet milling only, or (3) dry milling and wet milling The specimens were fabricated using hot pressing or pulsed electric current sintering (PECS) from planetary ball milled powders. In this study, elastic moduli, including Young's modulus, shear modulus, and Poisson's ratio, were measured dynamically using resonant ultrasound spectroscopy (RUS) at room temperature and as a function of temperature up to 663 K. The room temperature porosity dependence for Young's modulus followed the empirical exponential relationships common for brittle materials, with a material dependent constant bPE of 3.5 and 1.3 for LAST and PbTe-PbS, respectively. The room temperature Young's modulus for a theoretically dense specimen was 58.4 +/- 0.6 GPa and 56.2 +/- 0.4 GPa for for LAST and PbTe-PbS, respectively. For hot pressed PbTe-PbS specimens, the Vickers indentations mean hardness and fracture toughness was 1.18 + 0.09 GPa and 0.35 +/- 0.04 MPa·m 1/2. The coefficient of thermal expansion is important for understanding the mechanical response of a material to a thermal gradient or a thermal transient. For PbTe-PbS the coefficient of thermal expansion measured using dilatometry and high temperature x-ray diffraction was 21.5 x 10-6 K -1. Bloating during post-densification annealing was measured indirectly using resonant ultrasound spectroscopy and dilatometry and directly using scanning electron microscopy. Dry milled only PECS-processed PbTe-PbS specimens did not bloat during post-densification anneals up to 936 K. Hot pressed and PECS-processed specimens processed from wet milled and dry and wet milled powder bloated during densification anneals at temperatures over 603 K.

A novel personal cooling system (PCS) incorporated with phase change materials (PCMs) and ventilation fans: An investigation on its cooling efficiency.

PubMed

Lu, Yehu; Wei, Fanru; Lai, Dandan; Shi, Wen; Wang, Faming; Gao, Chuansi; Song, Guowen

2015-08-01

Personal cooling systems (PCS) have been developed to mitigate the impact of severe heat stress for humans working in hot environments. It is still a great challenge to develop PCSs that are portable, inexpensive, and effective. We studied the performance of a new hybrid PCS incorporating both ventilation fans and phase change materials (PCMs). The cooling efficiency of the newly developed PCS was investigated on a sweating manikin in two hot conditions: hot humid (HH, 34°C, 75% RH) and hot dry (HD, 34°C, 28% RH). Four test scenarios were selected: fans off with no PCMs (i.e., Fan-off, the CONTROL), fans on with no PCMs (i.e., Fan-on), fans off with fully solidified PCMs (i.e., PCM+Fan-off), and fans on with fully solidified PCMs (i.e., PCM+Fan-on). It was found that the addition of PCMs provided a 54∼78min cooling in HH condition. In contrast, the PCMs only offered a 19-39min cooling in HD condition. In both conditions, the ventilation fans greatly enhanced the evaporative heat loss compared with Fan-off. The hybrid PCS (i.e., PCM+Fan-on) provided a continuous cooling effect during the three-hour test and the average cooling rate for the whole body was around 111 and 315W in HH and HD conditions, respectively. Overall, the new hybrid PCS may be an effective means of ameliorating symptoms of heat stress in both hot-humid and hot-dry environments. Copyright © 2015 Elsevier Ltd. All rights reserved.

Waiting for Water

ERIC Educational Resources Information Center

Lamson-Nussbaum, Jorie

2013-01-01

The author waits in the hot and oppressive air while dust devils are born and die over the newly plowed field. It is a dry spring and she prays for rain. The lupine beans withered to dry threads last week and the corn that sprouted in a green haze over the north field is turning to brown paper. However, driving north, the author discovers the Rum…

Can disregard hot air quickly dry feces on transport cage flooring and eliminate campylobacter before cage re-use?

USDA-ARS?s Scientific Manuscript database

Allowing feces left on transport coops to dry is an effective way to reduce numbers of viable Campylobacter left by positive flocks. The problem with this approach is that poultry processors do not have the time, space or resources to maintain several times the minimum number of transport cages that...

Pressing of three-layer, dry-formed MDF with binderless hardboard faces

Treesearch

Otto Suchsland; George E. Woodson; Charles W. McMillin

1986-01-01

Severely cooked Masonite pulp was used as face material in three-layer experimental medium-density fiberboard (MDF). The core layer consisted of conventional MDF furnish with resin binder added. The faces were formed absolutely dry without additives of any kind. The three-layer mat was hot-pressed to overall densities ranging from 44 to 56 pcf. The faces had hardboard-...

Effects of A New Caul System on Strength and Stability of Structural Flakeboard

Treesearch

Cheng Piao; Todd F. Shupe; Chung Y. Hse

2004-01-01

Pressing flakes or fibers at high moisture content (MC) may generate substantial benefits for the manufacture of wood composites. Such technology could reduce furnish drying costs and the risk of fire hazard, improve panel mechanicaland moisture soaking properties, and reduce emission of volatile organic compounds (VOCs) at drying of flakes and at hot pressing. However...

Height growth and site index curves for Douglas-fir on dry sites in the Willamette National Forest.

Treesearch

Joseph E Means; Mary E. Helm

1985-01-01

Equations and curves are presented for estimating height and site index of Douglas-fir (Pseudotsuga menziesii (Mirb.) Franco) on hot, dry sites in the Willamette National Forest in western Oregon. The equations are based on the dissected stems of 27 trees. The curves differ from those previously published for Douglas-fir. Instructions are presented...

Effect of chitosan and cationic starch on the surface chemistry properties of bagasse paper.

PubMed

Ashori, Alireza; Cordeiro, Nereida; Faria, Marisa; Hamzeh, Yahya

2013-07-01

The use of non-wood fibers in the paper industry has been an economical and environmental necessity. The application of dry-strength agents has been a successful method to enhance the strength properties of paper. The experimental results evidencing the potential of chitosan and cationic starch utilization in bagasse paper subjected to hot water pre-extraction has been presented in this paper. The research analyzes the surface properties alterations due to these dry-strength agents. Inverse gas chromatography was used to evaluate the properties of surface chemistry of the papers namely the surface energy, active sites, surface area as well as the acidic/basic character. The results of the study revealed that the handsheets process causes surface arrangement and orientation of chemical groups, which induce a more hydrophobic and basic surface. The acid-base surface characteristics after the addition of dry-strength agents were the same as the bagasse handsheets with and without hot water pre-extraction. The results showed that the dry-strength agent acts as a protecting film or glaze on the surfaces of bagasse paper handsheets. Copyright © 2013 Elsevier B.V. All rights reserved.

The effect of clothing care activities on textile formaldehyde content.

PubMed

Novick, Rachel M; Nelson, Mindy L; McKinley, Meg A; Anderson, Grace L; Keenan, James J

2013-01-01

Textiles are commonly treated with formaldehyde-based residues that may potentially induce allergic contact dermatitis in sensitive individuals. This study examined the initial formaldehyde content in clothing and resulting changes due to care activities. Twenty clothing articles were examined and 17 of them did not have detectable levels of formaldehyde. One shirt contained a formaldehyde concentration of 3172 ppm, and two pairs of pants had formaldehyde concentrations of 1391 ppm and 86 ppm. The two highest results represent formaldehyde levels that are up to 40-fold greater than international textile regulations. The two items with the greatest formaldehyde content were washed and dried in a manner similar to that used by consumers, including hand and machine washing in hot or cold water followed by air or machine drying. The washing and drying procedures reduced formaldehyde levels to between 26 and 72% of untreated controls. Differences in the temperature or type of washing and drying did not result in a clear trend in the subsequent formaldehyde content. In addition, samples were hot ironed, which did not affect the formaldehyde content as significantly. Understanding the formaldehyde content in clothing and its potential reduction through care activities may be useful for manufacturers and formaldehyde-sensitive individuals.

Increases in the longevity of desiccation-phase developing rice seeds: response to high-temperature drying depends on harvest moisture content

PubMed Central

Whitehouse, K. J.; Hay, F. R.; Ellis, R. H.

2015-01-01

Background and Aims Previous studies have suggested that the drying conditions routinely used by genebanks may not be optimal for subsequent seed longevity. The aim of this study was to compare the effect of hot-air drying and low-temperature drying on subsequent seed longevity for 20 diverse rice accessions and to consider how factors related to seed production history might influence the results. Methods Seeds of rice, Oryza sativa, were produced according to normal regeneration procedures at IRRI. They were harvested at different times [harvest date and days after anthesis (DAA), once for each accession] and dried either in a drying room (DR; 15 % relative humidity, 15 °C) or in a flat-bed heated-air batch dryer (BD; 45 °C, 8 h d–1) for up to six daily cycles followed by drying in the DR. Relative longevity was assessed by storage at 10·9 % moisture content and 45 °C. Key Results Initial drying in the BD resulted in significantly greater longevity compared with the DR for 14 accessions (seed lots): the period of time for viability to fall to 50 % for seeds dried in the BD as a percentage of that for seeds dried throughout in the DR varied between 1.3 and 372·2 % for these accessions. The seed lots that responded the most were those that were harvested earlier in the season and at higher moisture content. Drying in the BD did not reduce subsequent longevity compared with DR drying for any of the remaining accessions. Conclusions Seeds harvested at a moisture content where, according to the moisture desorption isotherm, they could still be metabolically active (>16·2 %) may be in the first stage of the post-mass maturity, desiccation phase of seed development and thus able to increase longevity in response to hot-air drying. The genebank standards regarding seed drying for rice and, perhaps, for other tropical species should therefore be reconsidered. PMID:26133688

Increases in the longevity of desiccation-phase developing rice seeds: response to high-temperature drying depends on harvest moisture content.

PubMed

Whitehouse, K J; Hay, F R; Ellis, R H

2015-08-01

Previous studies have suggested that the drying conditions routinely used by genebanks may not be optimal for subsequent seed longevity. The aim of this study was to compare the effect of hot-air drying and low-temperature drying on subsequent seed longevity for 20 diverse rice accessions and to consider how factors related to seed production history might influence the results. Seeds of rice, Oryza sativa, were produced according to normal regeneration procedures at IRRI. They were harvested at different times [harvest date and days after anthesis (DAA), once for each accession] and dried either in a drying room (DR; 15 % relative humidity, 15 °C) or in a flat-bed heated-air batch dryer (BD; 45 °C, 8 h d(-1)) for up to six daily cycles followed by drying in the DR. Relative longevity was assessed by storage at 10·9 % moisture content and 45 °C. Initial drying in the BD resulted in significantly greater longevity compared with the DR for 14 accessions (seed lots): the period of time for viability to fall to 50 % for seeds dried in the BD as a percentage of that for seeds dried throughout in the DR varied between 1.3 and 372·2 % for these accessions. The seed lots that responded the most were those that were harvested earlier in the season and at higher moisture content. Drying in the BD did not reduce subsequent longevity compared with DR drying for any of the remaining accessions. Seeds harvested at a moisture content where, according to the moisture desorption isotherm, they could still be metabolically active (>16·2 %) may be in the first stage of the post-mass maturity, desiccation phase of seed development and thus able to increase longevity in response to hot-air drying. The genebank standards regarding seed drying for rice and, perhaps, for other tropical species should therefore be reconsidered. © The Author 2015. Published by Oxford University Press on behalf of the Annals of Botany Company.

Evaluation of browning ratio in an image analysis of apple slices at different stages of instant controlled pressure drop-assisted hot-air drying (AD-DIC).

PubMed

Gao, Kun; Zhou, Linyan; Bi, Jinfeng; Yi, Jianyong; Wu, Xinye; Zhou, Mo; Wang, Xueyuan; Liu, Xuan

2017-06-01

Computer vision-based image analysis systems are widely used in food processing to evaluate quality changes. They are able to objectively measure the surface colour of various products since, providing some obvious advantages with their objectivity and quantitative capabilities. In this study, a computer vision-based image analysis system was used to investigate the colour changes of apple slices dried by instant controlled pressure drop-assisted hot air drying (AD-DIC). The CIE L* value and polyphenol oxidase activity in apple slices decreased during the entire drying process, whereas other colour indexes, including CIE a*, b*, ΔE and C* values, increased. The browning ratio calculated by image analysis increased during the drying process, and a sharp increment was observed for the DIC process. The change in 5-hydroxymethylfurfural (5-HMF) and fluorescent compounds (FIC) showed the same trend with browning ratio due to Maillard reaction. Moreover, the concentrations of 5-HMF and FIC both had a good quadratic correlation (R 2  > 0.998) with the browning ratio. Browning ratio was a reliable indicator of 5-HMF and FIC changes in apple slices during drying. The image analysis system could be used to monitor colour changes, 5-HMF and FIC in dehydrated apple slices during the AD-DIC process. © 2016 Society of Chemical Industry. © 2016 Society of Chemical Industry.

Effect of the moisture content of forced hot air on the postharvest quality and bioactive compounds of mango fruit (Mangifera indica L. cv. Manila).

PubMed

Ornelas-Paz, José de Jesús; Yahia, Elhadi M

2014-04-01

The effectiveness of hot air treatments in controlling decay and insects in mango fruit has been demonstrated and has usually been assessed as a function of the temperature of the heated air and the duration of the treatment. However, the contribution of the moisture content of the heated air has received little attention, especially with regard to fruit quality. In this study, mango fruits (cv. Manila) at mature-green stage were treated with moist (95% relative humidity (RH)) or dry (50% RH) hot forced air (43 °C, at 2.5 m s(-1) for 220 min) and then held at 20 °C for 9 days and evaluated periodically. The heating rate was higher with moist air. Treatments with moist and dry air did not cause injury to the fruit. Treatment with moist air temporarily slowed down color development, softening, weight loss and β-carotene biosynthesis. This slowing down was clearly observed during the first 4-5 days at 20 °C. However, non-heated fruit and fruit heated with dry air showed similar quality at the end of storage. The moisture content of the heating air differentially modulated the postharvest ripening of 'Manila' mangoes. Moist air temporarily slowed down the ripening process of this mango cultivar. © 2013 Society of Chemical Industry.

Microwave-assisted drying of blueberry (Vaccinium corymbosum L.) fruits: Drying kinetics, polyphenols, anthocyanins, antioxidant capacity, colour and texture.

PubMed

Zielinska, Magdalena; Michalska, Anna

2016-12-01

The aim of the study was to evaluate the effect of hot air convective drying (HACD), microwave vacuum drying (MWVD) and their combination (HACD+MWVD) on the drying kinetics, colour, total polyphenols, anthocyanins antioxidant capacity and texture of frozen/thawed blueberries. Drying resulted in reduction of total polyphenols content and antioxidant capacity (69 and 77%, respectively). The highest content of total polyphenols was noted after HACD at 90°C. Lower air temperature and prolonged exposure to oxygen resulted in greater degradation of polyphenols and antioxidant capacity. Drying processes caused a significant decrease (from 70 to 95%) in the content of anthocyanins. The highest content of anthocyanins and the strongest antioxidant capacity was found in blueberries dried using HACD at 90°C+MWVD. Among drying methods, HACD at 90°C+MWVD satisfied significant requirements for dried fruits i.e. short drying time and improved product quality. Copyright © 2016 Elsevier Ltd. All rights reserved.

Effects of drying processes on starch-related physicochemical properties, bioactive components and antioxidant properties of yam flours.

PubMed

Chen, Xuetao; Li, Xia; Mao, Xinhui; Huang, Hanhan; Wang, Tingting; Qu, Zhuo; Miao, Jing; Gao, Wenyuan

2017-06-01

The effects of five different drying processes, air drying (AD), sulphur fumigation drying (SFD), hot air drying (HAD), freeze drying (FD) and microwave drying (MWD) for yams in terms of starch-related properties and antioxidant activity were studied. From the results of scanning electron microscopy (SEM), polarized optical microscopy (POM), X-ray diffraction (XRD), and Fourier transform infrared (FT-IR), the MWD sample was found to contain gelatinized starch granules. The FD yam had more slow digestible (SDS) and resistant starches (RS) compared with those processed with other modern drying methods. The bioactive components and the reducing power of the dried yams, were lower than those of fresh yam. When five dried samples were compared by principal component analysis, the HAD and SFD samples were observed to have the highest comprehensive principal component values. Based on our results, HAD would be a better method for yam drying than the more traditional SFD. Copyright © 2016 Elsevier Ltd. All rights reserved.

Effects of different drying methods on the product quality and volatile compounds of whole shiitake mushrooms.

PubMed

Tian, Yuting; Zhao, Yingting; Huang, Jijun; Zeng, Hongliang; Zheng, Baodong

2016-04-15

Various drying methods play important roles in the preservation of foods. However, how the different drying methods affect the quality of some foods is not clear. This paper evaluates the effects of hot air, vacuum, microwave, and microwave vacuum drying techniques on important qualities and volatile compounds of whole shiitake (Lentinus edodes) mushrooms. These four drying methods resulted in a significantly (p<0.05) increase in the content of total free amino acids and the relative content of sulfur compounds of dried products. Microwave vacuum drying helped to maintain larger amounts of taste-active amino acids, and improved nutrient retention and color attributes. Furthermore, the uniform honeycomb network created by microwave vacuum drying along with a less collapsed structure of dried samples can be used to explain the observed high rehydration ratio. Therefore, microwave vacuum drying should be a potential method for obtaining high-quality dried mushrooms. Copyright © 2015 Elsevier Ltd. All rights reserved.

Antibacterial activity of the lactoperoxidase system combined with edible Laminaria hot-water extract as a source of halide ions.

PubMed

Shin, Kouichirou; Nakano, Manabu; Yamauchi, Koji; Toida, Tomohiro; Iwatsuki, Keiji

2012-01-01

Hot-water extracts prepared from nine out of 12 samples of dried edible Laminaria reduced the viable numbers of Aggregatibacter actinomycetemcomitans, Staphylococcus aureus, and Esherichia coli below the detection limit after incubation for 5 min when combined with lactoperoxidase, glucose oxidase, and glucose. Some extracts showed higher bactericidal activity and a higher OI(-) concentration in the assay mixture after ultrafiltration.

Durable zinc ferrite sorbent pellets for hot coal gas desulfurization

DOEpatents

Jha, Mahesh C.; Blandon, Antonio E.; Hepworth, Malcolm T.

1988-01-01

Durable, porous sulfur sorbents useful in removing hydrogen sulfide from hot coal gas are prepared by water pelletizing a mixture of fine zinc oxide and fine iron oxide with inorganic and organic binders and small amounts of activators such as sodium carbonate and molybdenite; the pellets are dried and then indurated at a high temperature, e.g., 1800.degree. C., for a time sufficient to produce crush-resistant pellets.

Irradiation Maintains Functional Components of Dry Hot Peppers (Capsicum annuum L.) under Ambient Storage

PubMed Central

Iqbal, Qumer; Amjad, Muhammad; Asi, Muhammad Rafique; Nawaz, Aamir; Khan, Samiya Mahmood; Ariño, Agustin; Ahmad, Tanveer

2016-01-01

Hot peppers used as natural flavoring and coloring agents are usually irradiated in prepacked form for decontamination. The effects of gamma radiation on the stability of functional components such as capsaicinoids and antioxidant compounds (carotenoids, ascorbic acid and total phenolics) were investigated in hot peppers (Capsicum annuum). Whole dried peppers packed in polyethylene bags were gamma irradiated at 0 (control), 2, 4, and 6 kGy and subsequently stored at 25 °C for 90 days. The irradiation dose did not substantially affect the initial contents of capsaicinoids, ascorbic acid and total phenolics, though the concentration of carotenoids declined by 8% from the control (76.9 mg/100 g) to 6 kGy radiation dose (70.7 mg/100 g). Similarly, during storage for 90 days at ambient temperature the concentrations of capsaicinoids and total phenolics remained fairly stable with mean percent reductions from 3.3% to 4.2%, while the levels of total carotenoids and ascorbic acid significantly (p < 0.05) declined by 12% and 14%, respectively. Overall, neither irradiation nor subsequent ambient storage could appreciably influence the contents of functional components in hot peppers. These results revealed that gamma irradiation up to 6 kGy can be safely used for decontamination to meet the needs for overseas markets without compromising product quality. PMID:28231158

Irradiation Maintains Functional Components of Dry Hot Peppers (Capsicum annuum L.) under Ambient Storage.

PubMed

Iqbal, Qumer; Amjad, Muhammad; Asi, Muhammad Rafique; Nawaz, Aamir; Khan, Samiya Mahmood; Ariño, Agustin; Ahmad, Tanveer

2016-09-12

Hot peppers used as natural flavoring and coloring agents are usually irradiated in prepacked form for decontamination. The effects of gamma radiation on the stability of functional components such as capsaicinoids and antioxidant compounds (carotenoids, ascorbic acid and total phenolics) were investigated in hot peppers ( Capsicum annuum ). Whole dried peppers packed in polyethylene bags were gamma irradiated at 0 (control), 2, 4, and 6 kGy and subsequently stored at 25 °C for 90 days. The irradiation dose did not substantially affect the initial contents of capsaicinoids, ascorbic acid and total phenolics, though the concentration of carotenoids declined by 8% from the control (76.9 mg/100 g) to 6 kGy radiation dose (70.7 mg/100 g). Similarly, during storage for 90 days at ambient temperature the concentrations of capsaicinoids and total phenolics remained fairly stable with mean percent reductions from 3.3% to 4.2%, while the levels of total carotenoids and ascorbic acid significantly ( p < 0.05) declined by 12% and 14%, respectively. Overall, neither irradiation nor subsequent ambient storage could appreciably influence the contents of functional components in hot peppers. These results revealed that gamma irradiation up to 6 kGy can be safely used for decontamination to meet the needs for overseas markets without compromising product quality.

Study of a Novel Method for the Thermolysis of Solutes in Aqueous Solution Using a Low Temperature Bubble Column Evaporator.

PubMed

Shahid, Muhammad; Xue, Xinkai; Fan, Chao; Ninham, Barry W; Pashley, Richard M

2015-06-25

An enhanced thermal decomposition of chemical compounds in aqueous solution has been achieved at reduced solution temperatures. The technique exploits hitherto unrecognized properties of a bubble column evaporator (BCE). It offers better heat transfer efficiency than conventional heat transfer equipment. This is obtained via a continuous flow of hot, dry air bubbles of optimal (1-3 mm) size. Optimal bubble size is maintained by using the bubble coalescence inhibition property of some salts. This novel method is illustrated by a study of thermal decomposition of ammonium bicarbonate (NH4HCO3) and potassium persulfate (K2S2O8) in aqueous solutions. The decomposition occurs at significantly lower temperatures than those needed in bulk solution. The process appears to work via the continuous production of hot (e.g., 150 °C) dry air bubbles, which do not heat the solution significantly but produce a transient hot surface layer around each rising bubble. This causes the thermal decomposition of the solute. The decomposition occurs due to the effective collision of the solute with the surface of the hot bubbles. The new process could, for example, be applied to the regeneration of the ammonium bicarbonate draw solution used in forward osmosis.

A modelling study of the event-based retention performance of green roof under the hot-humid tropical climate in Kuching.

PubMed

Chai, C T; Putuhena, F J; Selaman, O S

2017-12-01

The influences of climate on the retention capability of green roof have been widely discussed in existing literature. However, knowledge on how the retention capability of green roof is affected by the tropical climate is limited. This paper highlights the retention performance of the green roof situated in Kuching under hot-humid tropical climatic conditions. Using the green roof water balance modelling approach, this study simulated the hourly runoff generated from a virtual green roof from November 2012 to October 2013 based on past meteorological data. The result showed that the overall retention performance was satisfactory with a mean retention rate of 72.5% from 380 analysed rainfall events but reduced to 12.0% only for the events that potentially trigger the occurrence of flash flood. By performing the Spearman rank's correlation analysis, it was found that the rainfall depth and mean rainfall intensity, individually, had a strong negative correlation with event retention rate, suggesting that the retention rate increases with decreased rainfall depth. The expected direct relationship between retention rate and antecedent dry weather period was found to be event size dependent.

Simultaneous application of microwave energy and hot air to whole drying process of apple slices: drying kinetics, modeling, temperature profile and energy aspect

NASA Astrophysics Data System (ADS)

Horuz, Erhan; Bozkurt, Hüseyin; Karataş, Haluk; Maskan, Medeni

2018-02-01

Drying kinetics, modeling, temperature profile and energy indices were investigated in apple slices during drying by a specially designed microwave-hot air domestic hybrid oven at the following conditions: 120, 150 and 180 W microwave powers coupled with 50, 60 and 70 °C air temperatures. Both sources of energy were applied simultaneously during the whole drying processes. The drying process continued until the moisture content of apple slices reached to 20% from 86.3% (wet basis, w.b). Drying times ranged from 330 to 800 min and decreased with increasing microwave power and air temperatures. The constant rate period was only observed at low microwave powers and air temperatures. Two falling rate periods were observed. Temperature of apple slices sharply increased within the first 60 min, then reached equilibrium with drying medium and finally increased at the end of the drying process. In order to describe drying behavior of apple slices nine empirical models were applied. The Modified Logistic Model fitted the best our experimental data ( R 2 = 0.9955-0.9998; χ 2 = 3.46 × 10-5-7.85 × 10-4 and RMSE = 0.0052-0.0221). The effective moisture and thermal diffusivities were calculated by Fick's second law and ranged from 1.42 × 10-9 to 3.31 × 10-9 m2/s and 7.70 × 10-9 to 12.54 × 10-9 m2/s, respectively. The activation energy ( Ea) values were calculated from effective moisture diffusivity ( Deff), thermal diffusivity ( α) and the rate constant of the best model ( k). The Ea values found from these three terms were similar and varied from 13.04 to 33.52 kJ/mol. Energy consumption and specific energy requirement of the hybrid drying of apple slices decreased and energy efficiency of the drying system increased with increasing microwave power and air temperature. Apples can be dried rapidly and effectively by use of the hybrid technique.

Hot Melt Extrusion and Spray Drying of Co-amorphous Indomethacin-Arginine With Polymers.

PubMed

Lenz, Elisabeth; Löbmann, Korbinian; Rades, Thomas; Knop, Klaus; Kleinebudde, Peter

2017-01-01

Co-amorphous drug-amino acid systems have gained growing interest as an alternative to common amorphous formulations which contain polymers as stabilizers. Several preparation methods have recently been investigated, including vibrational ball milling on a laboratory scale or spray drying in a larger scale. In this study, the feasibility of hot melt extrusion for continuous manufacturing of co-amorphous drug-amino acid formulations was examined, challenging the fact that amino acids melt with degradation at high temperatures. Furthermore, the need for an addition of a polymer in this process was evaluated. After a polymer screening via the solvent evaporation method, co-amorphous indomethacin-arginine was prepared by a melting-solvent extrusion process without and with copovidone. The obtained products were characterized with respect to their solid-state properties, non-sink dissolution behavior, and stability. Results were compared to those of spray-dried formulations with the same compositions and to spray-dried indomethacin-copovidone. Overall, stable co-amorphous systems could be prepared by extrusion without or with copovidone, which exhibited comparable molecular interaction properties to the respective spray-dried products, while phase separation was detected by differential scanning calorimetry in several cases. The formulations containing indomethacin in combination with arginine and copovidone showed enhanced dissolution behavior over the formulations with only copovidone or arginine. Copyright © 2016 American Pharmacists Association®. Published by Elsevier Inc. All rights reserved.

Extreme Heat

MedlinePlus

... stomach, arms, or legs Actions: Go to a cooler location. Remove excess clothing. Take sips of cool ... above 103 degrees) taken orally; red, hot, and dry skin with no sweat; rapid, strong pulse; dizziness; ...

Safe Replacement For Asbestos In Nickel/Hydrogen Cells

NASA Technical Reports Server (NTRS)

Scott, William E.

1993-01-01

Polyethylene fibers and potassium titanate particles perform as well as asbestos. New material for separators of nickel-hydrogen electrochemical cells offers performance similar to that of asbestos separator material without adverse health effects. In one version, separator contains pure polyethylene fibers, and may or may not contain supplementary latices as bonding agents. In standard wet-laying papermaking process, fibers pressed into mat, then dried. Mat used as is or pressed further in hot calender stack to soften and fuse fibers at crossing points. Treatment reduces porosity and increases resistance of mat to passage of air bubbles under pressure. In alternative version, matrix of 20 to 40 percent polyethylene fibers and 60 to 80 percent potassium titanate particles formed on paper machine, then dried. It, too, can be treated by hot calendering.

Community level analysis of opportunistically-breeding anurans in western Mexico

Treesearch

Paulette. L. Ford; J. Scott Norman

2006-01-01

Tropical dry forests are among the most seasonal habitats in the world. They are most common in hot lowlands outside the equatorial rain forest zone, where rainfall is more seasonal and the dry season is most pronounced, lasting for several weeks or months (Brown and Lomolino 1998). They are also some of the most threatened of the major tropical forest types, largely...

Influence of pre-drying treatments on physicochemical and organoleptic properties of explosion puff dried jackfruit chips.

PubMed

Yi, Jianyong; Zhou, Linyan; Bi, Jinfeng; Chen, Qinqin; Liu, Xuan; Wu, Xinye

2016-02-01

The effects of hot air drying (AD), freeze drying (FD), infrared drying (IR), microwave drying (MV), vacuum drying (VD) as pre-drying treatments for explosion puff drying (EPD) on qualities of jackfruit chips were studied. The lowest total color differences (∆E) were found in the FD-, MV- and VD-EPD dried chips. Volume expansion effect (9.2 %) was only observed in the FD-EPD dried chips, which corresponded to its well expanded honeycomb microstructures and high rehydration rate. Compared with AD-, IR-, MV- and VD-EPD, the FD-EPD dried fruit chips exhibited lower hardness and higher crispness, indicative of a crispier texture. FD-EPD dried fruits also obtained high retentions of ascorbic acid, phenolics and carotenoids compared with that of the other puffed products. The results of sensory evaluation suggested that the FD-EPD was a more beneficial combination because it enhanced the overall qualities of jackfruit chips. In conclusion, the FD-EPD could be used as a novel combination drying method for processing valuable and/or high quality fruit chips.

Effects of L-glutamine on rectal temperature and some markers of oxidative stress in Red Sokoto goats during the hot-dry season.

PubMed

Ocheja, Ohiemi Benjamin; Ayo, Joseph Olusegun; Aluwong, Tagang; Minka, Ndazo Salka

2017-08-01

The experiment investigated the ameliorative effects of L-glutamine administration on rectal temperature (RT), erythrocyte osmotic fragility (EOF), serum antioxidant enzyme activities and malondialdehyde (MDA) concentration in Red Sokoto goats during the hot-dry season. Twenty eight healthy Red Sokoto goats, comprising 14 experimental (administered 0.2 g/kg of L-glutamine dissolved in 10 mL of distilled water, once daily for 21 days) and 14 control (administered equivalent of distilled water) goats served as subjects. Rectal temperature (measured at 6:00, 13:00 and 18:00 h) and blood samples (taken at 8:00 h) were obtained from all subjects weekly, before, during and after L-glutamine administration. Data obtained were compared using one-way repeated-measures ANOVA, followed by Tukey's post-hoc test. The dry-bulb temperature, relative humidity and temperature-humidity index for the study period ranged between 24.0 and 37.5 °C, 26.0 and 84.0% and 73.0 and 86.3, respectively. L-glutamine administration decreased (P < 0.05) RT, EOF and MDA and increased superoxide dismutase (SOD) activity in experimental group, compared to controls during weeks 1, 2 and 3. Glutathione peroxidase (GPx) and catalase activities were higher (P < 0.05) in the experimental group than in the controls only during week 1 of L-glutamine administration. In conclusion, L-glutamine administration mitigated increases in RT, EOF and serum MDA concentration and enhanced serum SOD, GPx and catalase activities and may be beneficial in heat-stressed goats during the hot-dry season.

Validating the Heat Stress Indices for Using In Heavy Work Activities in Hot and Dry Climates.

PubMed

Hajizadeh, Roohalah; Golbabaei, Farideh; Farhang Dehghan, Somayeh; Beheshti, Mohammad Hossein; Jafari, Sayed Mohammad; Taheri, Fereshteh

2016-01-01

Necessity of evaluating heat stress in the workplace, require validation of indices and selection optimal index. The present study aimed to assess the precision and validity of some heat stress indices and select the optimum index for using in heavy work activities in hot and dry climates. It carried out on 184 workers from 40 brick kilns workshops in the city of Qom, central Iran (as representative hot and dry climates). After reviewing the working process and evaluation the activity of workers and the type of work, environmental and physiological parameters according to standards recommended by International Organization for Standardization (ISO) including ISO 7243 and ISO 9886 were measured and indices were calculated. Workers engaged in indoor kiln experienced the highest values of natural wet temperature, dry temperature, globe temperature and relative humidity among studied sections (P<0.05). Indoor workplaces had the higher levels of all environmental parameters than outdoors (P=0.0001), except for air velocity. The wet-bulb globe temperature (WBGT) and heat stress index (HSI) indices had the highest correlation with other physiological parameters among the other heat stress indices. Relationship between WBGT index and carotid artery temperature (r=0.49), skin temperature (r=0.319), and oral temperature (r=0.203) was statistically significant (P=0.006). Since WBGT index, as the most applicable index for evaluating heat stress in workplaces is approved by ISO, and due to the positive features of WBGT such as ease of measurement and calculation, and with respect to some limitation in application of HSI; WBGT can be introduced as the most valid empirical index of heat stress in the brick workshops.

An Overt Chemical Protective Garment Reduces Thermal Strain Compared with a Covert Garment in Warm-Wet but Not Hot-Dry Environments.

PubMed

Maley, Matthew J; Costello, Joseph T; Borg, David N; Bach, Aaron J E; Hunt, Andrew P; Stewart, Ian B

2017-01-01

Objectives: A commercial chemical, biological, radiological and nuclear (CBRN) protective covert garment has recently been developed with the aim of reducing thermal strain. A covert CBRN protective layer can be worn under other clothing, with equipment added for full chemical protection when needed. However, it is unknown whether the covert garment offers any alleviation to thermal strain during work compared with a traditional overt ensemble. Therefore, the aim of this study was to compare thermal strain and work tolerance times during work in an overt and covert ensemble offering the same level of CBRN protection. Methods : Eleven male participants wore an overt (OVERT) or covert (COVERT) CBRN ensemble and walked (4 km·h -1 , 1% grade) for a maximum of 120 min in either a wet bulb globe temperature [WBGT] of 21, 30, or 37°C (Neutral, WarmWet and HotDry, respectively). The trials were ceased if the participants' gastrointestinal temperature reached 39°C, heart rate reached 90% of maximum, walking time reached 120 min or due to self-termination. Results: All participants completed 120 min of walking in Neutral. Work tolerance time was greater in OVERT compared with COVERT in WarmWet ( P < 0.001, 116.5[9.9] vs. 88.9[12.2] min, respectively), though this order was reversed in HotDry ( P = 0.003, 37.3[5.3] vs. 48.4[4.6] min, respectively). The rate of change in mean body temperature and mean skin temperature was greater in COVERT (0.025[0.004] and 0.045[0.010]°C·min -1 , respectively) compared with OVERT (0.014[0.004] and 0.027[0.007]°C·min -1 , respectively) in WarmWet ( P < 0.001 and P = 0.028, respectively). However, the rate of change in mean body temperature and mean skin temperature was greater in OVERT (0.068[0.010] and 0.170[0.026]°C·min -1 , respectively) compared with COVERT (0.059[0.004] and 0.120[0.017]°C·min -1 , respectively) in HotDry ( P = 0.002 and P < 0.001, respectively). Thermal sensation, thermal comfort, and ratings of perceived exertion did not differ between garments at trial cessation ( P > 0.05). Conclusion: Those dressed in OVERT experienced lower thermal strain and longer work tolerance times compared with COVERT in a warm-wet environment. However, COVERT may be an optimal choice in a hot-dry environment. These findings have practical implications for those making decisions on the choice of CBRN ensemble to be used during work.

An Overt Chemical Protective Garment Reduces Thermal Strain Compared with a Covert Garment in Warm-Wet but Not Hot-Dry Environments

PubMed Central

Maley, Matthew J.; Costello, Joseph T.; Borg, David N.; Bach, Aaron J. E.; Hunt, Andrew P.; Stewart, Ian B.

2017-01-01

Objectives: A commercial chemical, biological, radiological and nuclear (CBRN) protective covert garment has recently been developed with the aim of reducing thermal strain. A covert CBRN protective layer can be worn under other clothing, with equipment added for full chemical protection when needed. However, it is unknown whether the covert garment offers any alleviation to thermal strain during work compared with a traditional overt ensemble. Therefore, the aim of this study was to compare thermal strain and work tolerance times during work in an overt and covert ensemble offering the same level of CBRN protection. Methods: Eleven male participants wore an overt (OVERT) or covert (COVERT) CBRN ensemble and walked (4 km·h−1, 1% grade) for a maximum of 120 min in either a wet bulb globe temperature [WBGT] of 21, 30, or 37°C (Neutral, WarmWet and HotDry, respectively). The trials were ceased if the participants' gastrointestinal temperature reached 39°C, heart rate reached 90% of maximum, walking time reached 120 min or due to self-termination. Results: All participants completed 120 min of walking in Neutral. Work tolerance time was greater in OVERT compared with COVERT in WarmWet (P < 0.001, 116.5[9.9] vs. 88.9[12.2] min, respectively), though this order was reversed in HotDry (P = 0.003, 37.3[5.3] vs. 48.4[4.6] min, respectively). The rate of change in mean body temperature and mean skin temperature was greater in COVERT (0.025[0.004] and 0.045[0.010]°C·min−1, respectively) compared with OVERT (0.014[0.004] and 0.027[0.007]°C·min−1, respectively) in WarmWet (P < 0.001 and P = 0.028, respectively). However, the rate of change in mean body temperature and mean skin temperature was greater in OVERT (0.068[0.010] and 0.170[0.026]°C·min−1, respectively) compared with COVERT (0.059[0.004] and 0.120[0.017]°C·min−1, respectively) in HotDry (P = 0.002 and P < 0.001, respectively). Thermal sensation, thermal comfort, and ratings of perceived exertion did not differ between garments at trial cessation (P > 0.05). Conclusion: Those dressed in OVERT experienced lower thermal strain and longer work tolerance times compared with COVERT in a warm-wet environment. However, COVERT may be an optimal choice in a hot-dry environment. These findings have practical implications for those making decisions on the choice of CBRN ensemble to be used during work. PMID:29170644

Fabrication and Characterization of CMOS-MEMS Thermoelectric Micro Generators

PubMed Central

Kao, Pin-Hsu; Shih, Po-Jen; Dai, Ching-Liang; Liu, Mao-Chen

2010-01-01

This work presents a thermoelectric micro generator fabricated by the commercial 0.35 μm complementary metal oxide semiconductor (CMOS) process and the post-CMOS process. The micro generator is composed of 24 thermocouples in series. Each thermocouple is constructed by p-type and n-type polysilicon strips. The output power of the generator depends on the temperature difference between the hot and cold parts in the thermocouples. In order to prevent heat-receiving in the cold part in the thermocouples, the cold part is covered with a silicon dioxide layer with low thermal conductivity to insulate the heat source. The hot part of the thermocouples is suspended and connected to an aluminum plate, to increases the heat-receiving area in the hot part. The generator requires a post-CMOS process to release the suspended structures. The post-CMOS process uses an anisotropic dry etching to remove the oxide sacrificial layer and an isotropic dry etching to etch the silicon substrate. Experimental results show that the micro generator has an output voltage of 67 μV at the temperature difference of 1 K. PMID:22205869

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

This volume contains the interim change notice for the safety operation procedure for hot cell. It covers the master-slave manipulators, dry waste removal, cell transfers, hoists, cask handling, liquid waste system, and physical characterization of fluids.

Impact of moderate and extreme climate change scenarios on growth, morphological features, photosynthesis, and fruit production of hot pepper.

PubMed

Lee, Sang Gyu; Kim, Sung Kyeom; Lee, Hee Ju; Lee, Hee Su; Lee, Jin Hyoung

2018-01-01

Horticultural crop production and changes in physiological aspects during the growing season may be affected by climate change factors (CC), which include increased temperature and the associated doubling or tripling of atmospheric CO 2 concentrations. However, the potential effects are complex and many parameters might impact on the observed effects. To evaluate the effects of CC, the growth, yield, fruit characteristics, photosynthetic traits, and morphological characteristics of hot peppers were investigated. The hot peppers were grown under two CC scenarios, with the Representative Concentration Pathway (RCP) of 4.5 (Temp.; +3.4°C, CO 2 conc.; 540 μmol/mol, Precipitation +17.3%) and RCP 8.5 (Temp.; +6.0°C and CO 2 conc.; 940 μmol/mol, Precipitation +20.3%), respectively, using extreme weather simulators. This was compared with existing weather conditions occurring in Jeonju, South Korea in terms of air temperature, relative humidity, radiation, and precipitation. Overall, the plant height showed the highest under moderate CC conditions (RCP 4.5) among all the treatments tested. The number of leaves in the RCP 8.5 condition showed 7,739/plants, which was 2.2 times higher than that of the control. In addition, fruit shape was shortened and percentage dry matter was also the highest. The yield of hot pepper in the CC RCP 4.5 and 8.5 conditions were decreased by 21.5% and 89.2% when compared with that of the control, respectively. The days to harvest in the condition of CC scenarios were shortened from 5 to 13 compared with that of control, predominantly due to the increased air temperature. The results indicated that the severe RCP CC scenarios made reduction in the yields and negative affection on the fruit qualities. Overall, hot pepper was tolerant of mild CC scenarios of temperature × CO 2 but was significantly affected by more extreme CC interacting parameter concentrations (or similar).

Dry-heat resistance of selected psychrophiles. [Viking lander in spacecraft sterilization

NASA Technical Reports Server (NTRS)

Winans, L.; Pflug, I. J.; Foster, T. L.

1977-01-01

The dry-heat resistance characteristics of spores of psychrophilic organisms isolated from soil samples from the Viking spacecraft assembly areas at Cape Kennedy Space Flight Center, Cape Canaveral, Fla., were studied. Spore suspensions were produced, and dry-heat D values were determined for the microorganisms that demonstrated growth or survival under a simulated Martian environment. The dry-heat tests were carried out by using the planchet-boat-hot plate system at 110 and 125 C with an ambient relative humidity of 50% at 22 C. The spores evaluated had a relatively low resistance to dry heat. D (110 C) values ranged from 7.5 to 122 min, whereas the D (125 C) values ranged from less than 1.0 to 9.8 min.

Dry-heat resistance of selected psychrophiles.

PubMed Central

Winans, L; Pflug, I J; Foster, T L

1977-01-01

The dry-heat resistance characteristics of spores of psychrophilic organisms isolated from soil samples from the Viking spacecraft assembly areas at Cape Kennedy Space Flight Center, Cape Canaveral, Fla., were studied. Spore suspensions were produced, and dry-heat D values were determined for the microorganisms that demonstrated growth or survival under a simulated Martian environment. The dry-heat tests were carried out by using the planchet-boat-hot plate system at 110 and 125 degrees C with an ambient relative humidity of 50% at 22 degrees C. The spores evaluated had a relatively low resistance to dry heat. D(110 degrees C) values ranged from 7.5 to 122 min, whereas the D(123 degrees C) values ranged from less than 1.0 to 9.8 min. PMID:410367

Long-Term Harvest Residue Retention Could Decrease Soil Bacterial Diversities Probably Due to Favouring Oligotrophic Lineages.

PubMed

Zhang, Yaling; Zhang, Manyun; Tang, Li; Che, Rongxiao; Chen, Hong; Blumfield, Tim; Boyd, Sue; Nouansyvong, Mone; Xu, Zhihong

2018-03-01

Harvest residues contain large stores of carbon (C) and nitrogen (N) in forest plantations. Decomposing residues can release labile C and N into soil and thus provide substrates for soil bacterial communities. Previous studies showed that residue retention could increase soil C and N pools and activate bacterial communities in the short term (≤ 10 years). The current study examined the effects of a long-term (19-year) harvest residue retention on soil total and water and hot water extractable C and N pools, as well as bacterial communities via Illumina MiSeq sequencing. The experiment was established in a randomised complete block design with four replications, southeast Queensland of Australia, including no (R0), single (R1, 51 to 74 t ha -1 dry matter) and double quantities (R2, 140 t ha -1 dry matter) of residues retained. Generally, no significant differences existed in total C and N, as well as C and N pools extracted by water and hot water among the three treatments, probably due to negligible amounts of labile C and N released from harvest residues. Soil δ 15 N significantly decreased from R0 to R1 to R2, probably due to reduced N leaching with residue retention (P < 0.001). Residue retention increased the relative abundances of Actinobacteria (P = 0.016) and Spartobacteria (P < 0.001), whereas decreased Betaproteobacteria (P = 0.050). This favour for the oligotrophic groups probably caused the decrease in the bacterial diversity as revealed by Shannon index (P = 0.025). Hence, our study suggests that residue retention is not an appropriate management practice in the long term.

Industrial applications of hot dry rock geothermal energy

NASA Astrophysics Data System (ADS)

Duchane, D. V.

1992-07-01

Geothermal resources in the form of naturally occurring hot water or steam have been utilized for many years. While these hydrothermal resources are found in many places, the general case is that the rock at depth is hot, but does not contain significant amounts of mobile fluid. An extremely large amount of geothermal energy is found around the world in this hot dry rock (HDR). Technology has been under development for more than twenty years at the Los Alamos National Laboratory in the United States and elsewhere to develop the technology to extract the geothermal energy from HDR in a form useful for electricity generation, space heating, or industrial processing. HDR technology is especially attractive for industrial applications because of the ubiquitous distribution of the HDR resource and the unique aspects of the process developed to recover it. In the HDR process, as developed at Los Alamos, water is pumped down a well under high pressure to open up natural joints in hot rock and create an artificial geothermal reservoir. Energy is extracted by circulating water through the reservoir. Pressurized hot water is returned to the surface through the production well, and its thermal energy is extracted for practical use. The same water is then recirculated through the system to mine more geothermal heat. Construction of a pilot HDR facility at Fenton Hill, NM, USA, has recently been completed by the Los Alamos National Laboratory. It consists of a large underground reservoir, a surface plant, and the connecting wellbores. This paper describes HDR technology and the current status of the development program. Novel industrial applications of geothermal energy based on the unique characteristics of the HDR energy extraction process are discussed.

Southwest Alaska Regional Geothermal Energy Project

DOE Office of Scientific and Technical Information (OSTI.GOV)

Holdmann, Gwen

2015-04-30

The village of Elim, Alaska is 96 miles west of Nome, on the Seward Peninsula. The Darby Mountains north of the village are rich with hydrothermal systems associated with the Darby granitic pluton(s). In addition to the hot springs that have been recorded and studied over the last 100 years, additional hot springs exist. They are known through a rich oral history of the region, though they are not labeled on geothermal maps. This research primarily focused on Kwiniuk Hot Springs, Clear Creek Hot Springs and Molly’s Hot Springs. The highest recorded surface temperatures of these resources exist at Clearmore » Creek Hot Springs (67°C). Repeated water sampling of the resources shows that maximum temperatures at all of the systems are below boiling.« less

Mapping hotspots of malaria transmission from pre-existing hydrology, geology and geomorphology data in the pre-elimination context of Zanzibar, United Republic of Tanzania.

PubMed

Hardy, Andrew; Mageni, Zawadi; Dongus, Stefan; Killeen, Gerry; Macklin, Mark G; Majambare, Silas; Ali, Abdullah; Msellem, Mwinyi; Al-Mafazy, Abdul-Wahiyd; Smith, Mark; Thomas, Chris

2015-01-22

Larval source management strategies can play an important role in malaria elimination programmes, especially for tackling outdoor biting species and for eliminating parasite and vector populations when they are most vulnerable during the dry season. Effective larval source management requires tools for identifying geographic foci of vector proliferation and malaria transmission where these efforts may be concentrated. Previous studies have relied on surface topographic wetness to indicate hydrological potential for vector breeding sites, but this is unsuitable for karst (limestone) landscapes such as Zanzibar where water flow, especially in the dry season, is subterranean and not controlled by surface topography. We examine the relationship between dry and wet season spatial patterns of diagnostic positivity rates of malaria infection amongst patients reporting to health facilities on Unguja, Zanzibar, with the physical geography of the island, including land cover, elevation, slope angle, hydrology, geology and geomorphology in order to identify transmission hot spots using Boosted Regression Trees (BRT) analysis. The distribution of both wet and dry season malaria infection rates can be predicted using freely available static data, such as elevation and geology. Specifically, high infection rates in the central and southeast regions of the island coincide with outcrops of hard dense limestone which cause locally elevated water tables and the location of dolines (shallow depressions plugged with fine-grained material promoting the persistence of shallow water bodies). This analysis provides a tractable tool for the identification of malaria hotspots which incorporates subterranean hydrology, which can be used to target larval source management strategies.

Coping with Rosacea: Tripwires

MedlinePlus

... Weather Sun exposure, hot weather, humidity, cold and wind have all been known to aggravate rosacea for ... against the naturally drying effects of cold and wind. top Tripwires - Stress Stress ranks high on the ...

Hot tearing studies in AA5182

NASA Astrophysics Data System (ADS)

van Haaften, W. M.; Kool, W. H.; Katgerman, L.

2002-10-01

One of the major problems during direct chill (DC) casting is hot tearing. These tears initiate during solidification of the alloy and may run through the entire ingot. To study the hot tearing mechanism, tensile tests were carried out in semisolid state and at low strain rates, and crack propagation was studied in situ by scanning electron microscopy (SEM). These experimentally induced cracks were compared with hot tears developed in an AA5182 ingot during a casting trial in an industrial research facility. Similarities in the microstructure of the tensile test specimens and the hot tears indicate that hot tearing can be simulated by performing tensile tests at semisolid temperatures. The experimental data were compared with existing hot tearing models and it was concluded that the latter are restricted to relatively high liquid fractions because they do not take into account the existence of solid bridges in the crack.

Legionnaires' Disease

MedlinePlus

... and Treatment Cooling Towers, Evaporative Condensers, and Fluid Coolers Humidifiers and Misters Domestic Water Systems Domestic Hot- ... 105° F, or 39° to 41° C) Cough (dry at first, later producing phlegm) Difficulty in breathing ...

Protecting Emergency Responders: Lessons Learned from Terrorist Attacks

DTIC Science & Technology

2002-03-05

Contact lenses tended to dry out when worn with respirators for long periods. Wet shoes and socks caused blisters.1 Trades panel members believed...the confusion and compounds the safety and rescue responsibilities of firefighters and other responders who are in the command structure. In the...enter eyes and to irritate them. Heavy labor in hot weather, which caused de- hydration and dry eyes, apparently compounded this problem at the sites

Experiments with classes of stock suitable for forest planting in the northern Rocky Mountains

Treesearch

W. G. Wahlenberg

1928-01-01

Except in unusually moist years the survival of planted stock in the northern Rocky Mountains, even on favorable slopes, has not been satisfactory. On good and poor sites alike, the principal cause of the unusual degree of mortality has been the combination of dry soil and dry winds during the hot days of July and August. The results have made it clear that the most...

Modification of Indirect Solar Dryer for Simplicia Production

NASA Astrophysics Data System (ADS)

Purnomo, C. W.; Indarti, S.

2018-03-01

Simplicia is natural ingredient for herbal medicine that has been subjected to drying only. This study aims to develop an appropriate drying equipment to produce dried leaves of sambung nyawa (Gynura procumbens (Lour.) Merr.) or also called “longevity spinach”. Typical indirect solar drier was modified to be able to process more fresh leaves in order to speed up the production. The modification was done using double solar collector and wind powered ventilation. The double solar collector was applied in order to collect more solar energy for larger dimension of drying chamber, while the wind-ventilator was installed to provide forced convection of hot air flow inside the dryer. The drying kinetic including the drying constants were investigated using three common thin layer drying equations to model the drying behavior of the leaves. The moisture ratio (MR) depletion with respect to the drying time (t) of the leaves can be well represented by equation of MR=1.1732exp(-0.0993.t)-0.1732exp(-17.3871.t).

Performance and carcass yield of crossbred dairy steers fed diets with different levels of concentrate.

PubMed

da Silva, Gabriel Santana; Chaves Véras, Antônia Sherlanea; de Andrade Ferreira, Marcelo; Moreira Dutra, Wilson; Menezes Wanderley Neves, Maria Luciana; Oliveira Souza, Evaristo Jorge; Ramos de Carvalho, Francisco Fernando; de Lima, Dorgival Morais

2015-10-01

The objective of this study was to evaluate the influence of diets with increasing concentrate levels (170, 340, 510 and 680 g/kg of total dry matter) on dry matter intake, digestibility, performance and carcass characteristics of 25 Holstein-Zebu crossbred dairy steers in a feedlot. A completely randomized design was used, and data were submitted to analysis of variance and regression. The dry matter intake and digestibility coefficients of all nutrients increased linearly. The total weight gain and average daily gain added 1.16 kg and 9.90 g, respectively, for each 10 g/kg increase in concentrate. The empty body weight, hot carcass weight and cold carcass weight responded linearly to increasing concentrate. The hot carcass yield and cold carcass yield, gains in empty body weight and carcass gain were also influenced, as were the efficiencies of carcass deposition and carcass deposition rate. It is concluded that increasing concentrate levels in feedlot diets increase the intake and digestibility of dry matter and other nutrients, improving the feed efficiency, performance and physical characteristics of the carcass. Furthermore and of importance concerning the climate change debate, evidence from the literature indicates that enteric methane production would be reduced with increasing concentrate levels such as those used.

Evaluation of two cleaning methods for the removal of asbestos fibers from carpet

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kominsky, J.R.; Freyberg, R.W.; Chesson, J.

The research study examined the effectiveness of dry vacuuming and wet cleaning for the removal of asbestos fibers from carpet, and evaluated the potential for fiber reentrainment during carpet cleaning activities. Routine carpet cleaning operations using high-efficiency particulate air (HEPA) filtered dry vacuum cleaners and HEPA-filtered hot-water extraction cleaners were simulated on carpet artificially contaminated with asbestos fibers. Overall, wet cleaning the carpet with a hot-water extraction cleaner reduced the level of asbestos contamination by approximately 70 percent. There was no significant evidence of either an increase or a decrease in the asbestos concentration after dry vacuuming. The level ofmore » asbestos contamination had no significant effect on the difference between the carpet asbestos concentrations before and after cleaning. Airborne asbestos concentrations were between two and four times greater during the carpet cleaning activities. The level of asbestos contamination in the carpet cleaning activities. The level of asbestos contamination in the carpet and the type of cleaning method used had no statistically significant effect on the difference between the airborne asbestos concentrations before and during cleaning.« less

Ice Thermal Storage Systems for LWR Supplemental Cooling and Peak Power Shifting

DOE Office of Scientific and Technical Information (OSTI.GOV)

Haihua Zhao; Hongbin Zhang; Phil Sharpe

2010-06-01

Availability of enough cooling water has been one of the major issues for the nuclear power plant site selection. Cooling water issues have frequently disrupted the normal operation at some nuclear power plants during heat waves and long draught. The issues become more severe due to the new round of nuclear power expansion and global warming. During hot summer days, cooling water leaving a power plant may become too hot to threaten aquatic life so that environmental regulations may force the plant to reduce power output or even temporarily to be shutdown. For new nuclear power plants to be builtmore » at areas without enough cooling water, dry cooling can be used to remove waste heat directly into the atmosphere. However, dry cooling will result in much lower thermal efficiency when the weather is hot. One potential solution for the above mentioned issues is to use ice thermal storage systems (ITS) that reduce cooling water requirements and boost the plant’s thermal efficiency in hot hours. ITS uses cheap off-peak electricity to make ice and uses those ice for supplemental cooling during peak demand time. ITS is suitable for supplemental cooling storage due to its very high energy storage density. ITS also provides a way to shift large amount of electricity from off peak time to peak time. Some gas turbine plants already use ITS to increase thermal efficiency during peak hours in summer. ITSs have also been widely used for building cooling to save energy cost. Among three cooling methods for LWR applications: once-through, wet cooling tower, and dry cooling tower, once-through cooling plants near a large water body like an ocean or a large lake and wet cooling plants can maintain the designed turbine backpressure (or condensation temperature) during 99% of the time; therefore, adding ITS to those plants will not generate large benefits. For once-through cooling plants near a limited water body like a river or a small lake, adding ITS can bring significant economic benefits and avoid forced derating and shutdown during extremely hot weather. For the new plants using dry cooling towers, adding the ice thermal storage systems can effectively reduce the efficiency loss and water consumption during hot weather so that new LWRs could be considered in regions without enough cooling water. \\ This paper presents the feasibility study of using ice thermal storage systems for LWR supplemental cooling and peak power shifting. LWR cooling issues and ITS application status will be reviewed. Two ITS application case studies will be presented and compared with alternative options: one for once-through cooling without enough cooling for short time, and the other with dry cooling. Because capital cost, especially the ice storage structure/building cost, is the major cost for ITS, two different cost estimation models are developed: one based on scaling method, and the other based on a preliminary design using Building Information Modeling (BIM), an emerging technology in Architecture/Engineering/Construction, which enables design options, performance analysis and cost estimating in the early design stage.« less

Influence of a glass wool hot vapour filter on yields and properties of bio-oil derived from rapid pyrolysis of paddy residues.

PubMed

Pattiya, Adisak; Suttibak, Suntorn

2012-07-01

This article reports experimental results of rapid or fast pyrolysis of rice straw (RS) and rice husk (RH) in a fluidised-bed reactor unit incorporated with a hot vapour filter. The objective of this research was to investigate the effects of pyrolysis temperatures and the use of glass wool hot vapour filtration on pyrolysis products. The results showed that the optimum pyrolysis temperatures for RS and RH were 405 and 452 °C, which gave maximum bio-oil yields of 54.1 and 57.1 wt.% on dry biomass basis, respectively. The use of the hot filter led to a reduction of 4-7 wt.% bio-oil yield. Nevertheless, the glass wool hot filtered bio-oils appeared to have better quality in terms of initial viscosity, solids content and ash content than the non-filtered ones. Copyright © 2012 Elsevier Ltd. All rights reserved.

Atopic dermatitis

MedlinePlus

... for as short a time as possible. Short, cooler baths are better than long, hot baths. Use gentle body washes and cleansers instead of regular soaps. DO NOT scrub or dry your skin too hard or for too long. ...

Future intensification of hydro-meteorological extremes: downscaling using the weather research and forecasting model

NASA Astrophysics Data System (ADS)

El-Samra, R.; Bou-Zeid, E.; Bangalath, H. K.; Stenchikov, G.; El-Fadel, M.

2017-12-01

A set of ten downscaling simulations at high spatial resolution (3 km horizontally) were performed using the Weather Research and Forecasting (WRF) model to generate future climate projections of annual and seasonal temperature and precipitation changes over the Eastern Mediterranean (with a focus on Lebanon). The model was driven with the High Resolution Atmospheric Model (HiRAM), running over the whole globe at a resolution of 25 km, under the conditions of two Representative Concentration Pathways (RCP) (4.5 and 8.5). Each downscaling simulation spanned one year. Two past years (2003 and 2008), also forced by HiRAM without data assimilation, were simulated to evaluate the model's ability to capture the cold and wet (2003) and hot and dry (2008) extremes. The downscaled data were in the range of recent observed climatic variability, and therefore corrected for the cold bias of HiRAM. Eight future years were then selected based on an anomaly score that relies on the mean annual temperature and accumulated precipitation to identify the worst year per decade from a water resources perspective. One hot and dry year per decade, from 2011 to 2050, and per scenario was simulated and compared to the historic 2008 reference. The results indicate that hot and dry future extreme years will be exacerbated and the study area might be exposed to a significant decrease in annual precipitation (rain and snow), reaching up to 30% relative to the current extreme conditions.

Effect of Infrared Blanching on Enzyme Activity and Retention of β-Carotene and Vitamin C in Dried Mango.

PubMed

Guiamba, Isabel R F; Svanberg, Ulf; Ahrné, Lilia

2015-06-01

The objectives of this work were to evaluate infrared (IR) dry blanching in comparison with conventional water blanching prior to hot air drying of mango to inactivate polyphenol oxidase (PPO) and ascorbic acid oxidase (AAO) enzymes, and to study its effect on color change and retention of vitamin C and β-carotene. Mango cylinders were blanched under similar temperature-time conditions either by IR heating or by immersion in a water bath during 2 min at 90 °C (high-temperature-short-time-HTST) or for 10 min at 65 °C (low-temperature-long-time-LTLT). After blanching mango was hot air dried at 70 °C. PPO was completely inactivated during the blanching treatments, but AAO had a moderate remaining activity after LTLT treatment (∼30%) and a low remaining activity after HTST treatment (9% to 15%). A higher retention of vitamin C was observed in mango subjected to IR dry blanching, 88.3 ± 1.0% (HTST) and 69.2 ± 2.9% (LTLT), compared with water blanching, 61.4 ± 5.3% (HTST) and 50.7 ± 9.6% (LTLT). All-trans-β-carotene retention was significantly higher in water blanched dried mango, 93.2 ± 5.2% (LTLT) and 91.4 ± 5.1% (HTST), compared with IR dry blanched, 73.6 ± 3.6% (LTLT) and 76.9 ± 2.9% (HTST). Increased levels of 13-cis-β-carotene isomer were detected only in IR dry blanched mango, and the corresponding dried mango also had a slightly darker color. IR blanching of mango prior to drying can improve the retention of vitamin C, but not the retention of carotenoids, which showed to be more dependent on the temperature than the blanching process. A reduction of drying time was observed in LTLT IR-blanching mango. © 2015 Institute of Food Technologists®

Effect of salt concentrations and drying methods on the quality and formation of histamine in dried milkfish (Chanos chanos).

PubMed

Hwang, Chiu-Chu; Lin, Chia-Min; Kung, Hsien-Feng; Huang, Ya-Ling; Hwang, Deng-Fwu; Su, Yi-Cheng; Tsai, Yung-Hsiang

2012-11-15

The effects of salt concentrations (0-15.0%) and drying methods on the quality of dried milkfish were studied. The results showed that the levels of aerobic plate counts, total coliform, water activity, moisture contents, total volatile basic nitrogen (TVBN) and thiobarbituric acid (TBA) of the dried milkfish samples prepared with the same drying method decreased with increased salt concentrations. The samples prepared with the cold-air drying method had better quality in term of lower TVBN and TBA values than those of samples prepared with other drying methods. The histamine contents in all samples, except two, prepared with various salt concentrations by different drying methods were less than 1.9 mg/100 g. Two unsalted samples prepared with hot-air drying at 35 °C and sun drying methods were found to contain histamine at levels of 249.7 and 67.4 mg/100 g, respectively, which were higher than the potential hazard level of 50 mg/100 g. Copyright © 2012 Elsevier Ltd. All rights reserved.

The Cause of the Hot Spot in Vegetation Canopies and Soils: Shadow-Hiding Versus Coherent Backscatter

NASA Technical Reports Server (NTRS)

Hapke, Bruce; DiMucci, Dominick; Nelson, Robert; Smythe, William

1996-01-01

Two different mechanisms, shadow-hiding and coherent backscatter, can cause a hot spot, or opposition effect, in the bidirectional reflectance of vegetation and soils. Because the two mechanisms sample different properties, it is important to know which one is primarily responsible in a given medium. This question can be answered by measuring the bidirectional reflectance in circularly polarized light. If the results of the limited experiments reported here can be extrapolated to a wider range of materials, it appears that the primary cause of the hot spot in most vegetation canopies and in moist, clumpy soils is shadow-hiding. However, in vegetation with large numbers of wavelength-sized structures, such as mosses, and in dry, fine-grained soils, the hot spot is dominated by coherent backscatter.

DMSP Special Sensor Microwave/Imager Calibration/Validation. Volume 1

DTIC Science & Technology

1990-01-01

each channel samples the hot load on every scan and commands a gain change up when the hot load is below 7/16th of the analog to digital converter range...OLS imagery. A threshold blanking technique was used to convert the manual analyses into synthetic digital images containing the cloud truth...should include OLS digital thermal infrared into the analysis. While this will be of use only in clear, relatively dry atmospheric conditions, the

Observation of local cloud and moisture feedbacks over high ocean and desert surface temperatures

NASA Technical Reports Server (NTRS)

Chahine, Moustafa T.

1995-01-01

New data on clouds and moisture, made possible by reanalysis of weather satellite observations, show that the atmosphere reacts to warm clusters of very high sea surface temperatures in the western Pacific Ocean with increased moisture, cloudiness, and convection, suggesting a negative feedback limiting the sea surface temperature rise. The reverse was observed over dry and hot deserts where both moisture and cloudiness decrease, suggesting a positive feedback perpetuating existing desert conditions. In addition, the observations show a common critical surface temperature for both oceans and land; the distribution of atmospheric moisture is observed to reach a maximum value when the daily surface temperatures approach 304 +/- 1 K. These observations reveal complex dynamic-radiative interactions where multiple processes act simultaneously at the surface as well as in the atmosphere to regulate the feedback processes.

Process for removing sulfur from sulfur-containing gases: high calcium fly-ash

DOEpatents

Rochelle, Gary T.; Chang, John C. S.

1991-01-01

The present disclosure relates to improved processes for treating hot sulfur-containing flue gas to remove sulfur therefrom. Processes in accordance with the present invention include preparing an aqueous slurry composed of a calcium alkali source and a source of reactive silica and/or alumina, heating the slurry to above-ambient temperatures for a period of time in order to facilitate the formation of sulfur-absorbing calcium silicates or aluminates, and treating the gas with the heat-treated slurry components. Examples disclosed herein demonstrate the utility of these processes in achieving improved sulfur-absorbing capabilities. Additionally, disclosure is provided which illustrates preferred configurations for employing the present processes both as a dry sorbent injection and for use in conjunction with a spray dryer and/or bagfilter. Retrofit application to existing systems is also addressed.

Downstream processing of a ternary amorphous solid dispersion: The impacts of spray drying and hot melt extrusion on powder flow, compression and dissolution.

PubMed

Davis, Mark T; Potter, Catherine B; Walker, Gavin M

2018-06-10

Downstream processing aspects of a stable form of amorphous itraconazole exhibiting enhanced dissolution properties were studied. Preparation of this ternary amorphous solid dispersion by either spray drying or hot melt extrusion led to significantly different powder processing properties. Particle size and morphology was analysed using scanning electron microscopy. Flow, compression, blending and dissolution were studied using rheometry, compaction simulation and a dissolution kit. The spray dried material exhibited poorer flow and reduced sensitivity to aeration relative to the milled extrudate. Good agreement was observed between differing forms of flow measurement, such as Flow Function, Relative flow function, Flow rate index, Aeration rate, the Hausner ratio and the Carr index. The stability index indicated that both powders were stable with respect to agglomeration, de-agglomeration and attrition. Tablet ability and compressibility studies showed that spray dried material could be compressed into stronger compacts than extruded material. Blending of the powders with low moisture, freely-flowing excipients was shown to influence both flow and compression. Porosity studies revealed that blending could influence the mechanism of densification in extrudate and blended extrudate formulations. Following blending, the powders were compressed into four 500 mg tablets, each containing a 100 mg dose of amorphous itraconazole. Dissolution studies revealed that the spray dried material released drug faster and more completely and that blending excipients could further influence the dissolution rate. Copyright © 2018 Elsevier B.V. All rights reserved.

[Effect and regulation of drying on quality of traditional Chinese medicine pills].

PubMed

Qi, Ya-Ru; Li, Yuan-Hui; Han, Li; Wu, Zhen-Feng; Yue, Peng-Fei; Wang, Xue-Cheng; Xiong, Yao-Kun; Yang, Ming

2017-06-01

The dry quality of traditional Chinese medicine pills is the hot spot of pills research, because their quality has a crucial effect on the efficacy and development of dosage forms. Through literature research and statistical analysis, we would review the current problems on the drying of traditional Chinese medicine pills in this paper, and surrounding the evaluation system for traditional Chinese medicine pills, analyze the characteristics of common drying equipment and processes as well as their effect on quality of pills, discuss the problems in drying equipment and process as well as quality, and put forward the corresponding strategies, hoping to provide new ideas and new methods for the quality improvement of traditional Chinese medicine pills and quality standards. Copyright© by the Chinese Pharmaceutical Association.

24. The DryingRoom in the coating mill at Lawrence, Mass. ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

24. The Drying-Room in the coating mill at Lawrence, Mass. After the paper has received its coating from the coating-machine shown in the previous picture, it passes in a continuous web to the drying-room. Blasts of hot air coming out of galvanized ducts beneath support it for a distance of 100 feet, until it reaches the drying-chamber in the rear of the room. Here it hangs in festoons much like those of cotton cloth shown on page 219. In the picture the paper is passing from right to left. After leaving the drying-room it is wound on rolls, as shown in the next picture. (p.238.) - Champion-International Paper Company, West bank of Spicket River at Canal Street, Lawrence, Essex County, MA

Application of Statistic Experimental Design to Assess the Effect of Gammairradiation Pre-Treatment on the Drying Characteristics and Qualities of Wheat

NASA Astrophysics Data System (ADS)

Yu, Yong; Wang, Jun

Wheat, pretreated by 60Co gamma irradiation, was dried by hot-air with irradiation dosage 0-3 kGy, drying temperature 40-60 °C, and initial moisture contents 19-25% (drying basis). The drying characteristics and dried qualities of wheat were evaluated based on drying time, average dehydration rate, wet gluten content (WGC), moisture content of wet gluten (MCWG)and titratable acidity (TA). A quadratic rotation-orthogonal composite experimental design, with three variables (at five levels) and five response functions, and analysis method were employed to study the effect of three variables on the individual response functions. The five response functions (drying time, average dehydration rate, WGC, MCWG, TA) correlated with these variables by second order polynomials consisting of linear, quadratic and interaction terms. A high correlation coefficient indicated the suitability of the second order polynomial to predict these response functions. The linear, interaction and quadratic effects of three variables on the five response functions were all studied.

Fruit Leathers: Method of Preparation and Effect of Different Conditions on Qualities

PubMed Central

Diamante, Lemuel M.; Bai, Xue; Busch, Janette

2014-01-01

Fruit leathers are dehydrated fruit products which are eaten as snacks or desserts. They are flexible sheets that have a concentrated fruit flavor and nutritional aspects. Most fruit leathers are prepared by mixing fruit puree and other additives like sugar, pectin, acid, glucose syrup, color, and potassium metabisulphite and then dehydrating them under specific conditions. Various drying systems including combined convective and far-infrared drying, hot air drying, microwave drying, solar drying, and sun drying have been used to make fruit leathers. Most fruit leathers are dried at 30 to 80°C for up to 24 hours until the target final moisture content (12–20%) has been reached. Research about fruit leathers began in the 1970s. This work has reviewed published papers on fruit leathers in order to summarize useful information about fruit leathers on methods of preparation, effects of drying condition, and effects of packaging and storage, which will be useful to many in the food industry and consumers who are health-conscious. PMID:26904618

Effect of different drying techniques on bioactive components, fatty acid composition, and volatile profile of robusta coffee beans.

PubMed

Dong, Wenjiang; Hu, Rongsuo; Chu, Zhong; Zhao, Jianping; Tan, Lehe

2017-11-01

This study investigated the effect of different drying techniques, namely, room-temperature drying (RTD), solar drying (SD), heat-pump drying (HPD), hot-air drying (HAD), and freeze drying (FD), on bioactive components, fatty acid composition, and the volatile compound profile of robusta coffee beans. The data showed that FD was an effective method to preserve fat, organic acids, and monounsaturated fatty acids. In contrast, HAD was ideal for retaining polyunsaturated fatty acids and amino acids. Sixty-two volatile compounds were identified in the differently dried coffee beans, representing 90% of the volatile compounds. HPD of the coffee beans produced the largest number of volatiles, whereas FD resulted in the highest volatile content. A principal component analysis demonstrated a close relationship between the HPD, SD, and RTD methods whereas the FD and HAD methods were significantly different. Overall, the results provide a basis for potential application to other similar thermal sensitive materials. Copyright © 2017 Elsevier Ltd. All rights reserved.

Data quality objectives for the initial fuel conditioning examinations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lawrence, L.A.

The Data Quality Objectives (DQOs) were established for the response of the first group of fuel samples shipped from the K West Basin to the Hanford 327 Building hot cells for examinations to the proposed Path Forward conditioning process. Controlled temperature and atmosphere furnace testing testing will establish performance parameters using the conditioning process (drying, sludge drying, hydride decomposition passivation) proposed by the Independent Technical Assessment (ITA) Team as the baseline.

40 CFR 63.7852 - What definitions apply to this subpart?

Code of Federal Regulations, 2012 CFR

2012-07-01

... hot metal, usually with dry air or nitrogen, to remove sulfur. Deviation means any instance in which... capture and collection of secondary emissions from a basic oxygen process furnace. Sinter cooler means the...

40 CFR 63.7852 - What definitions apply to this subpart?

Code of Federal Regulations, 2010 CFR

2010-07-01

... hot metal, usually with dry air or nitrogen, to remove sulfur. Deviation means any instance in which... capture and collection of secondary emissions from a basic oxygen process furnace. Sinter cooler means the...

40 CFR 63.7852 - What definitions apply to this subpart?

Code of Federal Regulations, 2013 CFR

2013-07-01

... hot metal, usually with dry air or nitrogen, to remove sulfur. Deviation means any instance in which... capture and collection of secondary emissions from a basic oxygen process furnace. Sinter cooler means the...

40 CFR 63.7852 - What definitions apply to this subpart?

Code of Federal Regulations, 2011 CFR

2011-07-01

... hot metal, usually with dry air or nitrogen, to remove sulfur. Deviation means any instance in which... capture and collection of secondary emissions from a basic oxygen process furnace. Sinter cooler means the...

40 CFR 63.7852 - What definitions apply to this subpart?

Code of Federal Regulations, 2014 CFR

2014-07-01

... hot metal, usually with dry air or nitrogen, to remove sulfur. Deviation means any instance in which... capture and collection of secondary emissions from a basic oxygen process furnace. Sinter cooler means the...

Robotics

NASA Technical Reports Server (NTRS)

Rothschild, Lynn J.

2012-01-01

Earth's upper atmosphere is an extreme environment: dry, cold, and irradiated. It is unknown whether our aerobiosphere is limited to the transport of life, or there exist organisms that grow and reproduce while airborne (aerophiles); the microenvironments of suspended particles may harbor life at otherwise uninhabited altitudes[2]. The existence of aerophiles would significantly expand the range of planets considered candidates for life by, for example, including the cooler clouds of a hot Venus-like planet. The X project is an effort to engineer a robotic exploration and biosampling payload for a comprehensive survey of Earth's aerobiology. While many one-shot samples have been retrieved from above 15 km, their results are primarily qualitative; variations in method confound comparisons, leaving such major gaps in our knowledge of aerobiology as quantification of populations at different strata and relative species counts[1]. These challenges and X's preliminary solutions are explicated below. X's primary balloon payload is undergoing a series of calibrations before beginning flights in Spring 2012. A suborbital launch is currently planned for Summer 2012. A series of ground samples taken in Winter 2011 is being used to establish baseline counts and identify likely background contaminants.

Foam-mat drying technology: A review.

PubMed

Hardy, Z; Jideani, V A

2017-08-13

This article reviews various aspects of foam-mat drying such as foam-mat drying processing technique, main additives used for foam-mat drying, foam-mat drying of liquid and solid foods, quality characteristics of foam-mat dried foods, and economic and technical benefits for employing foam-mat drying. Foam-mat drying process is an alternative method that allows the removal of water from liquid materials and pureed materials. In this drying process, a liquid material is converted into foam that is stable by being whipped after adding an edible foaming agent. The stable foam is then spread out in sheet or mat and dried by using hot air (40-90°C) at atmospheric pressure. Methyl cellulose (0.25-2%), egg white (3-20%), maltodextrin (0.5-05%), and gum Arabic (2-9%) are the commonly utilized additives for the foam-mat drying process at the given range, either combined together for their effectiveness or individual effect. The foam-mat drying process is suitable for heat sensitive, viscous, and sticky products that cannot be dried using other forms of drying methods such as spray drying because of the state of product. More interest has developed for foam-mat drying because of the simplicity, cost effectiveness, high speed drying, and improved product quality it provides.

Effect of different pretreatments on dried chilli (Capsicum annum L.) quality

NASA Astrophysics Data System (ADS)

Anoraga, S. B.; Sabarisman, I.; Ainuri, M.

2018-03-01

Chilli (Capsicum annum L.) has significant price fluctuation. When the chilli price is declined, it causes food waste from unsold chilli. Therefore, drying chilli is a solution for this condition. Futhermore, it can be processed for various product like chilli powder, chilli sauce, etc. The aim of this study was to investigate the effect of different pretreatments on dried chilli quality. Chilli was blenched with hot water and steam before drying. The purpose of this pretreatments is to inactivate enzyme that prevents color and vitamin C losses. The quality parameters were moisture content, colour, vitamin C content, and capsaicin. Changes were observed by gravimetri method for moisture content, chromameter in L* a * b * colour model, and iodine titration for vitamin C. After drying for 20 hours at 60°C, chilli with steam blanching pretreatment dried rapidly than other samples. Unpretreated chilli had higher vitamin C content and better color than blanched chilli.

Solar heating for a restaurant--North Little Rock, Arkansas

NASA Technical Reports Server (NTRS)

1981-01-01

Hot water consumption of large building affects solar-energy system design. Continual demand for hot water at restaurant makes storage less important than at other sites. Storage capacity of system installed in December 1979 equals estimated daily hot-water requirement. Report describes equipment specifications and modifications to existing building heating and hot water systems.

The Effects of US Army Chemical Protective Clothing on Speech Intelligibility, Visual Field, Body Mobility and Psychomotor Coordination of Men

DTIC Science & Technology

1987-09-01

soldiers wearing NBC clothing in hot/humid and hot/dry climates (Report MRL-R-826).Ascot Vale, Victoria, Australia : Materials Research Laboratories...Development and Engineering Center. 47. White, R.M. and Churchill, E. (1971). The body size of soldier-: U.S. Army anthropometry - 1966 (Tech. Rep. 72... Anthropometry of U.S. Army aviators - 1970 (Tech. Rep. 72-52-CE). Natick, MA: US Army Natick Laboratories. (AD 743 528) 112 ,7 r4 r

Methamphetamine (Meth)

MedlinePlus

... Users also complain of sweating, headaches, blurred vision, dry mouth, hot flashes, and dizziness. Because the drug often decreases or even eliminates appetite, it has been used as a dangerous dieting strategy for people trying to lose weight quickly. "Meth mouth" is ...

Gout

MedlinePlus

... red, hot and stiff joints. Gout happens when uric acid builds up in your body. Uric acid comes from the breakdown of substances called purines. ... liver, dried beans and peas, and anchovies. Normally, uric acid dissolves in the blood. It passes through the ...

Comparative Study of 28 and 18 Years Field Aged Siemens-Arco M55 Modules in Temperate and Hot-Dry Climates

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chicca, Matthew; Wohlgemuth, John; TamizhMani, GovindaSamy

The primary objective of this research work is two-fold: (i) determine the degradation rates of Siemens-Arco M55 modules exposed over 18 and 28 years in a hot-dry climate of Arizona and a temperate climate of California, and; (ii) identify the potential modes responsible for these degradation losses. The degradation rates were determined based on the I-V data obtained on exposed modules and on the corresponding control modules which were not exposed in the fields. The degradation modes responsible for these degradations were determined using several nondestructive tests and destructive tests performed on these control and exposed modules. The nondestructive testsmore » included: current-voltage, visual inspection, cell-module quantum efficiency, and module level reflectance spectroscopy. The destructive tests included: transmittance spectroscopy of glass superstrates, and FTIR, DSC and TGA of encapsulant materials.« less

Occurrence Prospect of HDR and Target Site Selection Study in Southeastern of China

NASA Astrophysics Data System (ADS)

Lin, W.; Gan, H.

2017-12-01

Hot dry rock (HDR) geothermal resource is one of the most important clean energy in future. Site selection a HDR resource is a fundamental work to explore the HDR resources. This paper compiled all the HDR development projects domestic and abroad, and summarized the location of HDR geothermal geological index. After comparing the geological background of HDR in the southeast coastal area of China, Yangjiang Xinzhou in Guangdong province, Leizhou Peninsula area, Lingshui in Hainan province and Huangshadong in Guangzhou were selected from some key potential target area along the southeast coast of China. Deep geothermal field model of the study area is established based on the comprehensive analysis of the target area of deep geothermal geological background and deep thermal anomalies. This paper also compared the hot dry rock resources target locations, and proposed suggestions for the priority exploration target area and exploration scheme.

Influence of grass pellet production on pyrrolizidine alkaloids occurring in Senecio aquaticus-infested grassland.

PubMed

Gottschalk, Christoph; Ostertag, Johannes; Meyer, Karsten; Gehring, Klaus; Thyssen, Stefan; Gareis, Manfred

2018-04-01

1,2-Dehydro-pyrrolizidine alkaloids (PA) and their N-oxides (PANO) exhibit acute and chronic toxic effects on the liver and other organs and therefore are a hazard for animal and human health. In certain regions of Germany, an increasing spread of Senecio spp. (ragwort) on grassland and farmland areas has been observed during the last years leading to a PA/PANO-contamination of feed and food of animal and plant origin. This project was carried out to elucidate whether the process of grass pellet production applying hot air drying influences the content of PA and PANO. Samples of hay (n = 22) and grass pellets (n = 28) originated from naturally infested grassland (around 10% and 30% dominance of Senecio aquaticus) and from a trial plot with around 50% dominance. Grass pellets were prepared from grass originating from exactly the same plots as the hay samples. The samples were analysed by liquid chromatography-tandem mass spectrometry for PA/PANO typically produced by this weed. The results of the study revealed that PA/PANO levels (predominantly sum of senecionine, seneciphylline, erucifoline and their N-oxides) in hay ranged between 2.1 and 12.6 mg kg -1 dry matter in samples with 10% and 30% dominance of S. aquaticus, respectively. Samples from the trial plot (50% dominance) had levels of up to 52.9 mg kg -1 . Notably, the hot air drying process during the production of grass pellets did not lead to a reduction of PA/PANO levels. Instead, the levels in grass pellets with 10% and 30% S. aquaticus ranged from 3.1 to 55.1 mg kg -1 . Grass pellets from the trial plot contained up to 96.8 mg kg -1 . In conclusion, hot air drying and grass pellet production did not affect PA/PANO contents in plant material and therefore, heat-dried products cannot be regarded as safe in view of the toxic potential of 1,2-dehydro-pyrrolizidine alkaloids.

A Mechanism for Recent Production of Liquid Water on Mars

NASA Technical Reports Server (NTRS)

Hecht, M. H.; Bridges, N. T.

2003-01-01

Though Mars is a cold, dry planet, with respect to the thermal stability of liquid water at low altitudes it is not terribly different from comparably cold places on Earth. In dry air such water would evaporate faster on Mars, at a rate comparable to a 60 C hot spring on Earth, but the heat loss associated with that evaporation would be mitigated by the poor thermal convection in the thin Martian air. Even at higher altitudes where the atmospheric pressure does not reach the triple point of water, liquid water might theoretically exist in a low-vapor pressure form such as wet soil, in a briny solution, or simply under a layer of dust or snow. The theoretical stability of liquid water does not suggest its occurrence, either on Mars or in Antarctica. In fact, global models have suggested that locations capable of providing sufficient heat for melting are, precisely for that reason, too dry for water to be present. However, the temperature of irregular local structures such as trenches or craters can be markedly warmer than those of the uniform surfaces of global models. The work described here suggests a plausible scenario in which seasonal liquid water might be produced locally, in sheltered locations, through a process of condensation, cold-trapping, buffering, and melting. While the amounts produced in the present climate would be small, copious amounts of meltwater may have been produced at other phases of the orbital cycle, as recently as 20,000 years ago.

Atmospheric Circulations of Rocky Planets as Heat Engines

NASA Astrophysics Data System (ADS)

Koll, D. D. B.

2017-12-01

Rocky planets are extremely common in the galaxy and include Earth, Mars, Venus, and hundreds of exoplanets. To understand and compare the climates of these planets, we need theories that are general enough to accommodate drastically different atmospheric and planetary properties. Unfortunately, few such theories currently exist.For Earth, there is a well-known principle that its atmosphere resembles a heat engine - the atmosphere absorbs heat near the surface, at a hot temperature, and emits heat to space in the upper troposphere, at a cold temperature, which allows it to perform work and balance dissipative processes such as friction. However, previous studies also showed that Earth's hydrological cycle uses up a large fraction of the heat engine's work output, which makes it difficult to view other atmospheres as heat engines.In this work I extend the heat engine principle from Earth towards other rocky planets. I explore both dry and moist atmospheres in an idealized general circulation model (GCM), and quantify their work output using entropy budgets. First, I show that convection and turbulent heat diffusion are important entropy sources in dry atmospheres. I develop a scaling that accounts for its effects, which allows me to predict the strength of frictional dissipation in dry atmospheres. There are strong parallels between my scaling and so-called potential intensity theory, which is a seminal theory for understanding tropical cyclones on Earth. Second, I address how moisture affects atmospheric heat engines. Moisture modifies both the thermodynamic properties of air and releases latent heat when water vapor condenses. I explore the impact of both effects, and use numerical simulations to explore the difference between dry and moist atmospheric circulations across a wide range of climates.

A survey of seasonal patterns in strongyle faecal worm egg counts of working equids of the central midlands and lowlands, Ethiopia.

PubMed

Getachew, M; Feseha, G; Trawford, A; Reid, S W J

2008-12-01

A study was conducted for two consecutive years (1998-1999) to determine the seasonal patterns of strongyle infection in working donkeys of Ethiopia. For the purpose 2385 donkeys from midland and lowland areas were examined for the presence of parasitic ova. A hundred percent prevalence of strongyle infection with similar seasonal pattern of strongyle faecal worm egg output was obtained in all study areas. However, seasonal variations in the number of strongyle faecal worm egg output were observed in all areas. The highest mean faecal worm egg outputs were recorded during the main rainy season (June to October) in both years in all areas. Although an increase in the mean strongyle faecal egg output was obtained in the short rainy season (March-April) followed by a drop in the short dry season (May), there was no statistically significant difference between the short rainy season and long dry season (Nov-Feb) (P > 0.05). A statistically significant difference however, was obtained between the main rainy season and short rainy season, and between the main rainy season and dry season (P < 0.05). Based on the results obtained it is suggested that the most economical and effective control of strongyles can be achieved by strategic deworming programme during the hot dry pre-main rainy season (May), when the herbage coverage is scarce and helminthologically 'sterile', and the arrested development of the parasites is suppose to be terminating. This could insure the greatest proportion of the existing worm population to be exposed to anthelmintic and also reduces pasture contamination and further infection in the subsequent wet season.

Mathematical modeling of drying of pretreated and untreated pumpkin.

PubMed

Tunde-Akintunde, T Y; Ogunlakin, G O

2013-08-01

In this study, drying characteristics of pretreated and untreated pumpkin were examined in a hot-air dryer at air temperatures within a range of 40-80 °C and a constant air velocity of 1.5 m/s. The drying was observed to be in the falling-rate drying period and thus liquid diffusion is the main mechanism of moisture movement from the internal regions to the product surface. The experimental drying data for the pumpkin fruits were used to fit Exponential, General exponential, Logarithmic, Page, Midilli-Kucuk and Parabolic model and the statistical validity of models tested were determined by non-linear regression analysis. The Parabolic model had the highest R(2) and lowest χ(2) and RMSE values. This indicates that the Parabolic model is appropriate to describe the dehydration behavior for the pumpkin.

Development and testing of dry chemicals in advanced extinguishing systems for jet engine nacelle fires

NASA Technical Reports Server (NTRS)

Altman, R. L.; Ling, A. C. (Editor); Mayer, L. A.; Myronik, D. J.

1979-01-01

The effectiveness of dry chemical in extinguishing and delaying reignition of fires resulting from hydrocarbon fuel leaking onto heated surfaces such as can occur in jet engine nacelles is studied. The commercial fire extinguishant dry chemical tried are sodium and potassium bicarbonate, carbonate, chloride, carbamate (Monnex), metal halogen, and metal hydroxycarbonate compounds. Synthetic and preparative procedures for new materials developed, a new concept of fire control by dry chemical agents, descriptions of experiment assemblages to test dry chemical fire extinguishant efficiencies in controlling fuel fires initiated by hot surfaces, comparative testing data for more than 25 chemical systems in a 'static' assemblage with no air flow across the heated surface, and similar comparative data for more than ten compounds in a dynamic system with air flows up to 350 ft/sec are presented.

Apparatus and method for investigation of energy consumption of microwave assisted drying systems.

PubMed

Göllei, Attila; Vass, András; Magyar, Attila; Pallai, Elisabeth

2009-10-01

Convective, hot air drying by itself is relatively efficient for removing water from the surface environment of agricultural seed products. However, moving internal moisture to the surface needs rather a long time, as a rule. The major research aim of the authors was to decrease the processing time and processing costs, to improve the quality of the dried product, and to increase drying efficiency. For this reason their research activities focused on the development of a special drying apparatus and a method suitable for measuring of energy conditions in a hybrid (microwave and convective) dryer. Experimental investigations were made with moistened wheat as model material. Experiments were carried out in microwave, convective and hybrid drying systems. The microwave drying alone was more efficient than the convective method. The lowest energy consumption and shortest drying time were obtained by the use of a hybrid method in which the waste energy of magnetron was utilized and the temperature was controlled. In this way, it was possible to keep the temperature of the dried product at a constant and safe value and to considerably decrease the energy consumption.

Study on vitamin D₂ stability in dried mushrooms during drying and storage.

PubMed

Sławińska, Aneta; Fornal, Emilia; Radzki, Wojciech; Skrzypczak, Katarzyna; Zalewska-Korona, Marta; Michalak-Majewska, Monika; Parfieniuk, Ewa; Stachniuk, Anna

2016-05-15

The main objective of this work was to determine the stability of vitamin D2 in dried mushrooms Agaricus bisporus, Pleurotus ostreatus and Lentinula edodes during storage, as well as to examine the possibility of inducing vitamin D2 production in dried mushrooms by UVB irradiation. After 1.5 year storage of dried mushrooms, the level of vitamin D2 in button mushrooms was found to be 6.90 μg/g dw, which is a 48.32% of initial level of vitamin D2. In the case of dried oyster and shiitake mushrooms there was a decrease to the level of 66.90% and 68.40%, respectively. It was determined that dried mushrooms can produce ergocalciferol under UVB irradiation. The highest content of vitamin D2 was observed in A. bisporus. Freeze-dried A. bisporus contained from 42.08 to 119.21 μg/g dw and hot-air dried mushrooms contained from 21.51 to 81.17 μg/g dw vitamin D2. Copyright © 2015 Elsevier Ltd. All rights reserved.

Modified dry limestone process for control of sulfur dioxide emissions

DOEpatents

Shale, Correll C.; Cross, William G.

1976-08-24

A method and apparatus for removing sulfur oxides from flue gas comprise cooling and conditioning the hot flue gas to increase the degree of water vapor saturation prior to passage through a bed of substantially dry carbonate chips or lumps, e.g., crushed limestone. The reaction products form as a thick layer of sulfites and sulfates on the surface of the chips which is easily removed by agitation to restore the reactive surface of the chips.

Installation Restoration Program Records Search for George Air Force Base, California

DTIC Science & Technology

1982-06-01

located in the Mojave Desert. The climate is arid with long hot summers and short cool winters. The mean 3relative humidity ranges from 27 percent in...abitat Native plant and animal comunities on base reflect the dry climatic conditions of an upland desert region. Along the eastern border of the bas...soil conditions because of a low ground- water table and the dry climatic conditions. While native systems are disrupted in the immediate vicinity of

Monitoring ultraviolet (UV) radiation inactivation of Cronobacter sakazakii in dry infant formula using Fourier transform infrared spectroscopy.

PubMed

Liu, Qian; Lu, Xiaonan; Swanson, Barry G; Rasco, Barbara A; Kang, Dong-Hyun

2012-01-01

Cronobacter sakazakii is an opportunistic pathogen associated with dry infant formula presenting a high risk to low birth weight neonates. The inactivation of C. sakazakii in dry infant formula by ultraviolet (UV) radiation alone and combined with hot water treatment at temperatures of 55, 60, and 65 °C were applied in this study. UV radiation with doses in a range from 12.1 ± 0.30 kJ/m² to 72.8 ± 1.83 kJ/m² at room temperature demonstrated significant inactivation of C. sakazakii in dry infant formula (P < 0.05). UV radiation combining 60 °C hot water treatment increased inactivation of C. sakazakii cells significantly (P < 0.05) in reconstituted infant formula. Significant effects of UV radiation on C. sakazakii inactivation kinetics (D value) were not observed in infant formula reconstituted in 55 and 65 °C water (P > 0.05). The inactivation mechanism was investigated using vibrational spectroscopy. Infrared spectroscopy detected significant stretching mode changes of macromolecules on the basis of spectral features, such as DNA, proteins, and lipids. Minor changes on cell membrane composition of C. sakazakii under UV radiation could be accurately and correctly monitored by infrared spectroscopy coupled with 2nd derivative transformation and principal component analysis. © 2011 Institute of Food Technologists®

Effect of ultrasound pre-treatment on the drying kinetics of brown seaweed Ascophyllum nodosum.

PubMed

Kadam, Shekhar U; Tiwari, Brijesh K; O'Donnell, Colm P

2015-03-01

The effect of ultrasound pre-treatment on the drying kinetics of brown seaweed Ascophyllum nodosum under hot-air convective drying was investigated. Pretreatments were carried out at ultrasound intensity levels ranging from 7.00 to 75.78 Wcm(-2) for 10 min using an ultrasonic probe system. It was observed that ultrasound pre-treatments reduced the drying time required. The shortest drying times were obtained from samples pre-treated at 75.78 Wcm(-2). The fit quality of 6 thin-layer drying models was also evaluated using the determination of coefficient (R(2)), root means square error (RMSE), AIC (Akaike information criterion) and BIC (Bayesian information criterion). Drying kinetics were modelled using the Newton, Henderson and Pabis, Page, Wang and Singh, Midilli et al. and Weibull models. The Newton, Wang and Singh, and Midilli et al. models showed the best fit to the experimental drying data. Color of ultrasound pretreated dried seaweed samples were lighter compared to control samples. It was concluded that ultrasound pretreatment can be effectively used to reduce the energy cost and drying time for drying of A. nodosum. Copyright © 2014 Elsevier B.V. All rights reserved.

Enzyme Production by Industrially Relevant Fungi Cultured on Coproduct From Corn Dry Grind Ethanol Plants

NASA Astrophysics Data System (ADS)

Ximenes, Eduardo A.; Dien, Bruce S.; Ladisch, Michael R.; Mosier, Nathan; Cotta, Michael A.; Li, Xin-Liang

Distillers dried grain with solubles (DDGS) is the major coproduct produced at a dry grind ethanol facility. Currently, it is sold primarily as a ruminant animal feed. DDGS is low cost and relatively high in protein and fiber contents. In this study, DDGS was investigated as carbon source for extracellular hydrolytic enzyme production. Two filamentous fungi, noted for their high cellulolytic and hemicellulolytic enzyme titers, were grown on DDGS: Trichoderma reesei Rut C-30 and Aspergillus niger NRRL 2001. DDGS was either used as delivered from the plant (untreated) or after being pretreated with hot water. Both microorganisms secreted a broad range of enzymes when grown on DDGS. Higher xylanase titers were obtained when cultured on hot water DDGS compared with growth on untreated DDGS. Maximum xylanase titers were produced in 4 d for A. niger and 8 d for T. reesei in shake flask cultures. Larger amounts of enzymes were produced in bioreactors (5L) either equipped with Rushton (for T. reesei) or updraft marine impellers (A. niger). Initial production titers were lower for bioreactor than for flask cultures, especially for T. reesei cultures. Improvement of enzyme titers were obtained using fed-batch feeding schemes.

Hot temperatures during the dry season reduce survival of a resident tropical bird.

PubMed

Woodworth, Bradley K; Norris, D Ryan; Graham, Brendan A; Kahn, Zachary A; Mennill, Daniel J

2018-05-16

Understanding how climate change will shape species distributions in the future requires a functional understanding of the demographic responses of animals to their environment. For birds, most of our knowledge of how climate influences population vital rates stems from research in temperate environments, even though most of Earth's avian diversity is concentrated in the tropics. We evaluated effects of Southern Oscillation Index (SOI) and local temperature and rainfall at multiple temporal scales on sex-specific survival of a resident tropical bird, the rufous-and-white wren Thryophilus rufalbus , studied over 15 years in the dry forests of northwestern Costa Rica. We found that annual apparent survival of males was 8% higher than females, more variable over time, and responded more strongly to environmental variation than female survival, which did not vary strongly with SOI or local weather. For males, mean and maximum local temperatures were better predictors of survival than either rainfall or SOI, with high temperatures during the dry season and early wet season negatively influencing survival. These results suggest that, even for species adapted to hot environments, further temperature increases may threaten the persistence of local populations in the absence of distributional shifts. © 2018 The Author(s).

Use of a double chip seal to correct a flushing hot mix asphalt pavement in Washington state - final report.

DOT National Transportation Integrated Search

2016-09-01

A double chip seal was applied to an existing hot mix asphalt (HMA) pavement to mitigate severe flushing that existed throughout the project. Special care was taken to adjust the amount of binder used to account for the degree of flushing in the exis...

75 FR 8036 - Monitor-Hot Creek Rangeland Project

Federal Register 2010, 2011, 2012, 2013, 2014

2010-02-23

... DEPARTMENT OF AGRICULTURE Forest Service Monitor-Hot Creek Rangeland Project AGENCY: Forest... Rangeland Project area. The analysis will determine if a change in management direction for livestock grazing is needed to move existing resource conditions within the Monitor-Hot Creek Rangeland Project area...

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sloan, J.M.; Pergantis, C.G.

Organic and organo-metallic coatings are presently being applied over bare copper as an approach to improve the co-planarity of circuit boards. Conformal organic solderability preservative coatings (OSP) are environmentally and economically advantageous over the more commonly used lead based coatings. Problems arise in assessing the solderability of the bare copper and the integrity of the organic coating. Specular reflectance Fourier transform infrared spectroscopy (FT-IR) was utilized to monitor and evaluate the formation of Cu oxides occurring on copper substrates used in the manufacturing of electronic circuit boards. Previous studies reported the utility of this technique. By measuring the oxide andmore » protective coating characteristics of these surfaces, their solderability performance can rapidly be evaluated in a manufacturing environment. OSP coated test specimens were subjected to hot-dry and hot-wet environmental conditions using MIL-STD-202F and MIL-STD-883E as guides. The resultant FT-IR spectra provided clear evidence for the formation of various Cu oxides at the Cu/OSP interface over exposure time, for the samples subjected to the hot-dry environment. IR spectral bands consistent with O-Cu-O and Cu{sub 2}O{sub 2} formation appear, while very minimal deterioration to the OSP coating was observed. The appearance of the Cu oxide layers grew steadily with increased environmental exposure. Specimens subjected to the hot-wet conditions showed no significant signs of deterioration. The IR data can be directly correlated to solderability performance as evaluated by wet balance testing.« less

Luminescence induced by dehydration of kaolin - Association with electron-spin-active centers and with surface activity for dehydration-polymerization of glycine

NASA Technical Reports Server (NTRS)

Coyne, L.; Hovatter, W.; Sweeney, M.

1983-01-01

Experimental data concerning emission of light upon dehydration as a function of preheating and pre-gamma-irradiation are correlated with reported studies of electron-spin resonance (ESR) activity after similar pretreatments. The effect of these pretreatments on the kaolin-promoted incorporation of glycine into peptide oligomers in a wet/cold, hot/dry fluctuating environment is compared to their effect on the ESR and luminescent signals. The existence of spectroscopically active centers appears to be loosely anticorrelated with reaction yield; these yields are increased by increasing the overall energy content of the material. It is concluded that some part of the chemical yield is produced by a mechanism involving intrinsic, excited electronic states of the clay crystal lattice. These states may be derived from thermally, interfacially, and/or mechanically induced charge reorganization within interspersed energy levels in the band structure of the material.

Hydrovolcanism

NASA Technical Reports Server (NTRS)

Sheridan, M. F.; Wohletz, K. H.

1985-01-01

Hydrovolcanism is a common phenomena produced by the interaction of magma or magmatic heat with an external source of water, such as a surface body, an aquifer, or a glacier. The effects include hydrofracture of existing rock units in the subsurface and the formation of hyaloclastites in a subaqueous environment. Hydroexplosions originate within a few kilometers of the surface. They may be relatively small, phreatic events or devastating complex blasts. Large-scale experiments determined that the optimal mixing ratio of water to basaltic melt (thermite plus silicates) for efficient conversion of thermal energy into mechanical energy is in the range of 0.1 to 0.3. Based on experimental results, eruptions can be classified as dominantly magmatic if the ratio of external water to magma is less than 0.2. Eruptions with water/melt ratios in the range of 0.2 to 1.0 are highly explosive and carry tephra in a hot vapor that contains dominantly superheated (dry) steam.

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

?Ducts in conditioned space (DCS) represent a high priority measure for moving the next generation of new homes to the Zero Net Energy performance level. Various strategies exist for incorporating ducts within the conditioned thermal envelope. To support this activity, in 2013 the Pacific Gas & Electric Company initiated a project with Davis Energy Group (lead for the Building America team, Alliance for Residential Building Innovation) to solicit builder involvement in California to participate in field demonstrations of various DCS strategies. Builders were given incentives and design support in exchange for providing site access for construction observation, diagnostic testing, andmore » builder survey feedback. Information from the project was designed to feed into California's 2016 Title 24 process, but also to serve as an initial mechanism to engage builders in more high performance construction strategies. This Building America project complemented information collected in the California project with BEopt simulations of DCS performance in hot/dry climate regions.« less

LASIK and dry eye.

PubMed

Toda, Ikuko

2007-01-01

Dry eye is one of the most common complications after laser-assisted in situ keratomileusis (LASIK). The clinical signs of post-LASIK dry eye include positive vital staining of ocular surface, decreased tear film breakup time and Schirmer test, reduced corneal sensitivity, and decreased functional visual acuity. The symptoms and signs last at least 1 month after LASIK. Although the mechanisms for developing post-LASIK dry eye are not completely understood, loss of corneal innervation by flap-making may affect the reflex loops of the corneal-lacrimal gland, corneal-blinking, and blinking-meibomian gland, and blinking-meibomian gland, resulting in decreased aqueous and lipid tear secretion and mucin expression. As LASIK enhancement by flap-lifting induces less dry eye symptoms and signs than first surgery, it is suggested that other factors rather than loss of neurotrophic effect may be involved in the mechanisms of post-LASIK dry eye. The treatments of dry eye include artificial tears, topical cyclosporine, hot compress, punctal plugs, and autologous serum eye drops. For patients with severe preoperative dry eye, a combination of punctal plugs and serum eye drops is required to be used before surgery.

Immobilization of radioiodine in synthetic boracite

DOEpatents

Babad, H.; Strachan, D.M.

1982-09-23

A nuclear waste storage product is disclosed in which radioiodine is incorporated in a synthetic boracite. The boracite may be prepared by reacting a transition metal iodide with an alkali horate under mild hydrothermal conditions, drying the reaction product, and then hot pressing.

21 CFR 177.1010 - Acrylic and modified acrylic plastics, semirigid and rigid.

Code of Federal Regulations, 2013 CFR

2013-04-01

...) Selection of extractability conditions. These are to be chosen as provided in § 176.170(c) of this chapter..., weighed platinum dish, evaporated to 2-5 milliliters on a nonsparking, low-temperature hot plate and dried...

21 CFR 177.1010 - Acrylic and modified acrylic plastics, semirigid and rigid.

Code of Federal Regulations, 2011 CFR

2011-04-01

...) Selection of extractability conditions. These are to be chosen as provided in § 176.170(c) of this chapter..., weighed platinum dish, evaporated to 2-5 milliliters on a nonsparking, low-temperature hot plate and dried...

21 CFR 177.1010 - Acrylic and modified acrylic plastics, semirigid and rigid.

Code of Federal Regulations, 2012 CFR

2012-04-01

...) Selection of extractability conditions. These are to be chosen as provided in § 176.170(c) of this chapter..., weighed platinum dish, evaporated to 2-5 milliliters on a nonsparking, low-temperature hot plate and dried...

Design and Development of Mopping Robot-'HotBot'

NASA Astrophysics Data System (ADS)

Khan, M. R.; Huq, N. M. L.; Billah, M. M.; Ahmmad, S. M.

2013-12-01

To have a healthy, comfortable, and fresh civilized life we need to do some unhealthy households. Cleaning the dirty floor with a mop is one of the most disgusting and scary house hold jobs. Mopping robots are a solution of such problem. However, these robots are still on the way to be smart enough. Many points limit their efficiency, i.e. cleaning sticky dirt, having dry floor after cleaning, monitoring, cost etc. 'HotBot' is a mopping robot that can clean dirty floor with nice efficiency leaving no sticky dirt. Hot water can be used for heavy stains or normal water for usual situation and economy. It needs neither to be monitored during mopping nor to wipe the floor after it. 'HotBot' has sensors to detect obstacles and a control mechanism to avoid those. Moreover, it cleans sequentially and equipped with several accident-protection-systems. Moreover, it is also cost effective compared to the robots available so far.

The effect of side-chain substitution and hot processing on diketopyrrolopyrrole-based polymers for organic solar cells.

PubMed

Heintges, Gaël H L; Leenaers, Pieter J; Janssen, René A J

2017-07-14

The effects of cold and hot processing on the performance of polymer-fullerene solar cells are investigated for diketopyrrolopyrrole (DPP) based polymers that were specifically designed and synthesized to exhibit a strong temperature-dependent aggregation in solution. The polymers, consisting of alternating DPP and oligothiophene units, are substituted with linear and second position branched alkyl side chains. For the polymer-fullerene blends that can be processed at room temperature, hot processing does not enhance the power conversion efficiencies compared to cold processing because the increased solubility at elevated temperatures results in the formation of wider polymer fibres that reduce charge generation. Instead, hot processing seems to be advantageous when cold processing is not possible due to a limited solubility at room temperature. The resulting morphologies are consistent with a nucleation-growth mechanism for polymer fibres during drying of the films.

Influence of drying temperature on dietary fibre, rehydration properties, texture and microstructure of Cape gooseberry (Physalis peruviana L.).

PubMed

Vega-Gálvez, Antonio; Zura-Bravo, Liliana; Lemus-Mondaca, Roberto; Martinez-Monzó, Javier; Quispe-Fuentes, Issis; Puente, Luis; Di Scala, Karina

2015-04-01

The effects of air drying temperature on dietary fibre, texture and microstructure of the Cape gooseberry fruits during convective dehydration in the range of 50-90 ºC were investigated. The ratio of insoluble dietary fibre to soluble dietary fibre was higher than 7:1 for all dehydrated samples. At 50 ºC tissue structure damage was evidenced leading to the maximum water holding capacity (47.4 ± 2.8 g retained water/100 g water) and the lowest rehydration ratio (1.15 ± 0.06 g absorbed water/g d.m.). Texture analysis showed effects of drying temperatures on TPA parameters. Changes in microstructure tissue were also observed at the studied drying temperatures. Hot air drying technology leads not only to fruit preservation but also increases and adds value to Cape gooseberry, an asset to develop new functional products.

Impact of pretreatment and downstream processing technologies on economics and energy in cellulosic ethanol production.

PubMed

Kumar, Deepak; Murthy, Ganti S

2011-09-05

While advantages of biofuel have been widely reported, studies also highlight the challenges in large scale production of biofuel. Cost of ethanol and process energy use in cellulosic ethanol plants are dependent on technologies used for conversion of feedstock. Process modeling can aid in identifying techno-economic bottlenecks in a production process. A comprehensive techno-economic analysis was performed for conversion of cellulosic feedstock to ethanol using some of the common pretreatment technologies: dilute acid, dilute alkali, hot water and steam explosion. Detailed process models incorporating feedstock handling, pretreatment, simultaneous saccharification and co-fermentation, ethanol recovery and downstream processing were developed using SuperPro Designer. Tall Fescue (Festuca arundinacea Schreb) was used as a model feedstock. Projected ethanol yields were 252.62, 255.80, 255.27 and 230.23 L/dry metric ton biomass for conversion process using dilute acid, dilute alkali, hot water and steam explosion pretreatment technologies respectively. Price of feedstock and cellulose enzymes were assumed as $50/metric ton and 0.517/kg broth (10% protein in broth, 600 FPU/g protein) respectively. Capital cost of ethanol plants processing 250,000 metric tons of feedstock/year was $1.92, $1.73, $1.72 and $1.70/L ethanol for process using dilute acid, dilute alkali, hot water and steam explosion pretreatment respectively. Ethanol production cost of $0.83, $0.88, $0.81 and $0.85/L ethanol was estimated for production process using dilute acid, dilute alkali, hot water and steam explosion pretreatment respectively. Water use in the production process using dilute acid, dilute alkali, hot water and steam explosion pretreatment was estimated 5.96, 6.07, 5.84 and 4.36 kg/L ethanol respectively. Ethanol price and energy use were highly dependent on process conditions used in the ethanol production plant. Potential for significant ethanol cost reductions exist in increasing pentose fermentation efficiency and reducing biomass and enzyme costs. The results demonstrated the importance of addressing the tradeoffs in capital costs, pretreatment and downstream processing technologies.

Impact of pretreatment and downstream processing technologies on economics and energy in cellulosic ethanol production

PubMed Central

2011-01-01

Background While advantages of biofuel have been widely reported, studies also highlight the challenges in large scale production of biofuel. Cost of ethanol and process energy use in cellulosic ethanol plants are dependent on technologies used for conversion of feedstock. Process modeling can aid in identifying techno-economic bottlenecks in a production process. A comprehensive techno-economic analysis was performed for conversion of cellulosic feedstock to ethanol using some of the common pretreatment technologies: dilute acid, dilute alkali, hot water and steam explosion. Detailed process models incorporating feedstock handling, pretreatment, simultaneous saccharification and co-fermentation, ethanol recovery and downstream processing were developed using SuperPro Designer. Tall Fescue (Festuca arundinacea Schreb) was used as a model feedstock. Results Projected ethanol yields were 252.62, 255.80, 255.27 and 230.23 L/dry metric ton biomass for conversion process using dilute acid, dilute alkali, hot water and steam explosion pretreatment technologies respectively. Price of feedstock and cellulose enzymes were assumed as $50/metric ton and 0.517/kg broth (10% protein in broth, 600 FPU/g protein) respectively. Capital cost of ethanol plants processing 250,000 metric tons of feedstock/year was $1.92, $1.73, $1.72 and $1.70/L ethanol for process using dilute acid, dilute alkali, hot water and steam explosion pretreatment respectively. Ethanol production cost of $0.83, $0.88, $0.81 and $0.85/L ethanol was estimated for production process using dilute acid, dilute alkali, hot water and steam explosion pretreatment respectively. Water use in the production process using dilute acid, dilute alkali, hot water and steam explosion pretreatment was estimated 5.96, 6.07, 5.84 and 4.36 kg/L ethanol respectively. Conclusions Ethanol price and energy use were highly dependent on process conditions used in the ethanol production plant. Potential for significant ethanol cost reductions exist in increasing pentose fermentation efficiency and reducing biomass and enzyme costs. The results demonstrated the importance of addressing the tradeoffs in capital costs, pretreatment and downstream processing technologies. PMID:21892958

In support of a hot hand in professional basketball and baseball.

PubMed

Shea, Stephen

2014-06-01

Recent studies have found little empirical evidence to suggest that National Basketball Association (NBA) and Major League Baseball (MLB) players have hot streaks. This has led some to suggest that hot hands do not exist and that offensive and defensive strategies adjusting to perceived hot hands are suboptimal. We study the MLB's Home Run Derby and the NBA's 3-point Shootout. When there is no defense, extended time between shots has been removed, and shot or swing selection is constant, we find evidence that player performance is nonstationary. Our results are consistent with beliefs long held by players, coaches, and fans, research on the importance of self-efficacy in sports, and studies that support the existence of hot streaks in sports with no or limited defense. © 2013 The Institute of Psychology, Chinese Academy of Sciences and Wiley Publishing Asia Pty Ltd.

Adhesion International 1987. Proceedings of the Annual Meeting of the Adhesion Society, Inc. (10th) Held in Williamsburg, Virginia on 23-27 February 1987

DTIC Science & Technology

1987-01-01

Sons, New York, 1983). The Effect of Electrochemical Potentials on the Durability of Rubber /Metal Bonds in Sea Watert A. STEVENSON Materials...cohesive fracture through the rubber . As a control experiment, a set of new dry testpieces were cut at the bond to various depths-simulating the full...melts are a new class of adhesives. They are created to improve the heat performance of hot melts without losing the advantages of hot melts, for

Hot air drum evaporator. [Patent application

DOEpatents

Black, R.L.

1980-11-12

An evaporation system for aqueous radioactive waste uses standard 30 and 55 gallon drums. Waste solutions form cascading water sprays as they pass over a number of trays arranged in a vertical stack within a drum. Hot dry air is circulated radially of the drum through the water sprays thereby removing water vapor. The system is encased in concrete to prevent exposure to radioactivity. The use of standard 30 and 55 gallon drums permits an inexpensive compact modular design that is readily disposable, thus eliminating maintenance and radiation build-up problems encountered with conventional evaporation systems.

Hot air drum evaporator

DOEpatents

Black, Roger L.

1981-01-01

An evaporation system for aqueous radioactive waste uses standard 30 and 55 gallon drums. Waste solutions form cascading water sprays as they pass over a number of trays arranged in a vertical stack within a drum. Hot dry air is circulated radially of the drum through the water sprays thereby removing water vapor. The system is encased in concrete to prevent exposure to radioactivity. The use of standard 30 and 55 gallon drums permits an inexpensive compact modular design that is readily disposable, thus eliminating maintenance and radiation build-up problems encountered with conventional evaporation systems.

Taboos and forest governance: informal protection of hot spot dry forest in southern Madagascar.

PubMed

Tengö, Maria; Johansson, Kristin; Rakotondrasoa, Fanambinantsoa; Lundberg, Jakob; Andriamaherilala, Jean-Aimé; Rakotoarisoa, Jean-Aimé; Elmqvist, Thomas

2007-12-01

In the dry forest of southern Madagascar, a region of global conservation priority, formally protected areas are nearly totally absent. We illustrate how the continued existence of unique forest habitats in the Androy region is directly dependent on informal institutions, taboos, regulating human behavior. Qualitative interviews to map and analyze the social mechanisms underlying forest protection have been combined with vegetation analyses of species diversity and composition. Of 188 forest patches, 93% were classified as protected, and in Southern Androy all remaining forest patches larger than 5 ha were protected. Eight different types of forests, with a gradient of social fencing from open access to almost complete entry prohibitions, were identified. Transgressions were well enforced with strong sanctions of significant economic as well as religious importance. Analyses of species diversity between protected and unprotected forests were complicated because of size differences and access restrictions. However, since, for example, in southern Androy >90% of the total remaining forest cover is protected through taboos, these informal institutions represent an important, and presently the only, mechanism for conservation of the highly endemic forest species. We conclude that social aspects, such as local beliefs and legitimate sanctioning systems, need to be analyzed and incorporated along with biodiversity studies for successful conservation.

Estimation of cauliflower mass transfer parameters during convective drying

NASA Astrophysics Data System (ADS)

Sahin, Medine; Doymaz, İbrahim

2017-02-01

The study was conducted to evaluate the effect of pre-treatments such as citric acid and hot water blanching and air temperature on drying and rehydration characteristics of cauliflower slices. Experiments were carried out at four different drying air temperatures of 50, 60, 70 and 80 °C with the air velocity of 2.0 m/s. It was observed that drying and rehydration characteristics of cauliflower slices were greatly influenced by air temperature and pre-treatment. Six commonly used mathematical models were evaluated to predict the drying kinetics of cauliflower slices. The Midilli et al. model described the drying behaviour of cauliflower slices at all temperatures better than other models. The values of effective moisture diffusivities ( D eff ) were determined using Fick's law of diffusion and were between 4.09 × 10-9 and 1.88 × 10-8 m2/s. Activation energy was estimated by an Arrhenius type equation and was 23.40, 29.09 and 26.39 kJ/mol for citric acid, blanch and control samples, respectively.

Carbon farming in hot, dry coastal areas: an option for climate change mitigation

NASA Astrophysics Data System (ADS)

Becker, K.; Wulfmeyer, V.; Berger, T.; Gebel, J.; Münch, W.

2012-10-01

We present a comprehensive, interdisciplinary project which demonstrates that large-scale plantations of Jatropha curcas - if established in hot, dry coastal areas around the world - could capture 17-25 tonnes of carbon dioxide per hectare per year from the atmosphere (averaged over 20 yr). Based on recent farming results it is confirmed that the Jatropha curcas plant is well adapted to harsh environments and is capable of growing alone or in combination with other tree and shrub species with minimal irrigation in hot deserts where rain occurs only sporadically. Our investigations indicate that there is sufficient unused and marginal land for the widespread cultivation of Jatropha curcas to reduce significantly the current upward trend in atmospheric CO2 levels. In a system in which desalinated seawater is used for irrigation and for delivery of mineral nutrients, the sequestration costs were estimated to range from 42-63 € per tonne CO2. This result makes carbon farming a technology that is competitive with carbon capture and storage (CCS). In addition, high-resolution simulations using an advanced land-surface-atmosphere model indicate that a 10 000 km2 plantation could produce a reduction in mean surface temperature and an onset or increase in rain and dew fall at a regional level.

Office-like Test Chambers to Measure Cool Roof Energy Savings in Four Indian Climates

DOE Office of Scientific and Technical Information (OSTI.GOV)

Arumugam, Rathish; B, Sasank; T, Rajappa

Selecting a high albedo (solar reflectance) waterproofing layer on the top of a roof helps lower the roof’s surface temperature and reduce the air conditioning energy consumption in the top floor of a building. The annual energy savings depend on factors including weather, internal loads, and building operation schedule. To demonstrate the energy saving potential of high albedo roofs, an apparatus consisting of two nearly identical test chambers (A and B) has been built in four Indian climates: Chennai (hot & humid), Bangalore (temperate), Jhagadia (Hot & dry) and Delhi (composite). Each chamber has well-insulated walls to mimic the coremore » of an office building. Both chambers have the same construction, equipment, and operating schedule, differing only in roof surface. The reinforced cement concrete roof of Chamber A is surfaced with a low-albedo cement layer, while that of Chamber B is surfaced with a high-albedo water proof membrane (change in solar reflectance of 0.28). The experiment will be carried out for one year to explore seasonal variations in energy savings. Initial results in the month of July (post summer) shows that savings from high albedo roof ranges from 0.04 kWh/m2/day in temperate climates, to 0.08 kWh/m2/day in hot & dry climate.« less

Building America Case Study: Performance of a Hot-Dry Climate Whole House Retrofit, Stockton, California (Fact Sheet)

DOE Office of Scientific and Technical Information (OSTI.GOV)

ARBI

2014-09-01

The Stockton house retrofit is a two-story tudor style single family deep retrofit in the hot-dry climate of Stockton, CA. The home is representative of a deep retrofit option of the scaled home energy upgrade packages offered to targeted neighborhoods under the pilot Large-Scale Retrofit Program (LSRP) administered by the Alliance for Residential Building Innovation (ARBI). Deep retrofit packages expand on the standard package by adding HVAC, water heater and window upgrades to the ducting, attic and floor insulation, domestic hot water insulation, envelope sealing, lighting and ventilation upgrades. Site energy savings with the deep retrofit were 23% compared tomore » the pre-retrofit case, and 15% higher than the savings estimated for the standard retrofit package. Energy savings were largely a result of the water heater upgrade, and a combination of the envelope sealing, insulation and HVAC upgrade. The HVAC system was of higher efficiency than the building code standard. Overall the financed retrofit would have been more cost effective had a less expensive HVAC system been selected and barriers to wall insulation remedied. The homeowner experienced improved comfort throughout the monitored period and was satisfied with the resulting utility bill savings.« less

A Hot Spring Origin of Life and Early Adaptive Pathway from Woese Progenotes to Marine Stromatolites

NASA Astrophysics Data System (ADS)

Norkus, R.; Damer, B. F.; Deamer, D. W.

2017-07-01

An origin of life on land is visualized as: organic compounds accumulating in hydrothermal pools, wet-dry cycling of protocells encapsulating synthesized polymers, arising of a Woese progenote and its evolution into living microbial communities.

Geothermal Energy Potential in Western United States

ERIC Educational Resources Information Center

Pryde, Philip R.

1977-01-01

Reviews types of geothermal energy sources in the western states, including hot brine systems and dry steam systems. Conversion to electrical energy is a major potential use of geothermal energy, although it creates environmental disruptions such as noise, corrosion, and scaling of equipment. (AV)

21 CFR 177.1010 - Acrylic and modified acrylic plastics, semirigid and rigid.

Code of Federal Regulations, 2014 CFR

2014-04-01

.... These are to be chosen as provided in § 176.170(c) of this chapter. (2) Preparation of samples... milliliters on a nonsparking, low-temperature hot plate and dried in 212 °F oven for 30 minutes. The residue...

Fitness-related differences in the rate of whole-body total heat loss in exercising young healthy women are heat-load dependent.

PubMed

Lamarche, Dallon T; Notley, Sean R; Poirier, Martin P; Kenny, Glen P

2018-03-01

What is the central question of this study? Aerobic fitness modulates heat loss, albeit the heat load at which fitness-related differences occur in young healthy women remains unclear. What is the main finding and its importance? We demonstrate using direct calorimetry that fitness modulates heat loss in a heat-load dependent manner, with differences occurring between young women of low and high fitness and matched physical characteristics when the metabolic heat load is at least 400 W in hot, dry conditions. Although fitness has been known for some time to modulate heat loss, our findings define the metabolic heat load at which fitness-related differences occur. Aerobic fitness has recently been shown to alter heat loss capacity in a heat-load dependent manner in young men. However, given that sex-related differences in heat loss capacity exist, it is unclear whether this response is consistent in women. We therefore assessed whole-body total heat loss in young (21 ± 3 years old) healthy women matched for physical characteristics, but with low (low-fit; 35.8 ± 4.5 ml O 2  kg -1  min -1 ) or high aerobic fitness (high-fit; 53.1 ± 5.1 ml O 2  kg -1  min -1 ; both n = 8; indexed by peak oxygen consumption), during three 30 min bouts of cycling performed at increasing rates of metabolic heat production of 250 (Ex1), 325 (Ex2) and 400 W (Ex3), each separated by a 15 min recovery, in hot, dry conditions (40°C, 11% relative humidity). Whole-body total heat loss (evaporative ± dry heat exchange) and metabolic heat production were measured using direct and indirect calorimetry, respectively. Body heat content was measured as the temporal summation of heat production and loss. Total heat loss did not differ during Ex1 (low-fit, 215 ± 16 W; high-fit, 231 ± 20 W; P > 0.05) and Ex2 (low-fit, 278 ± 15 W; high-fit, 301 ± 20 W; P > 0.05), but was lower in the low-fit (316 ± 21 W) compared with the high-fit women (359 ± 32 W) during Ex3 (P < 0.01). Consequently, the low-fit group stored 1.3-fold more heat (429 ± 61 kJ) throughout the three exercise bouts relative to the high-fit group (330 ± 113 kJ; P < 0.05). We show that aerobic fitness independently modulates heat loss capacity during exercise in hot, dry conditions in women separated by a peak oxygen consumption of ∼17 ml O 2  kg -1  min -1 starting at a metabolic heat load of 400 W. © 2017 The Authors. Experimental Physiology © 2017 The Physiological Society.

Recent developments in high efficient freeze-drying of fruits and vegetables assisted by microwave: A review.

PubMed

Fan, Kai; Zhang, Min; Mujumdar, Arun S

2018-01-10

Microwave heating has been applied in the drying of high-value solids as it affords a number of advantages, including shorter drying time and better product quality. Freeze-drying at cryogenic temperature and extremely low pressure provides the advantage of high product quality, but at very high capital and operating costs due partly to very long drying time. Freeze-drying coupled with a microwave heat source speeds up the drying rate and yields good quality products provided the operating unit is designed and operated to achieve the potential for an absence of hot spot developments. This review is a survey of recent developments in the modeling and experimental results on microwave-assisted freeze-drying (MFD) over the past decade. Owing to the high costs involved, so far all applications are limited to small-scale operations for the drying of high-value foods such as fruits and vegetables. In order to promote industrial-scale applications for a broader range of products further research and development efforts are needed to offset the current limitations of the process. The needs and opportunities for future research and developments are outlined.

Ammonium and phosphate enrichment across the dry-wet transition and their ecological relevance in a subtropical reservoir, China.

PubMed

Mo, Qiongli; Chen, Nengwang; Zhou, Xingpeng; Chen, Jixin; Duan, Shuiwang

2016-07-13

Small river reservoirs are widespread and can be ecologically sensitive across the dry-wet transition under monsoon climate with respect to nutrient loading and phenology. Monthly sampling and high-frequency in situ measurements were conducted for a river reservoir (southeast China) in 2013-2014 to examine the seasonal pattern of nutrients and phytoplankton. We found that nutrient concentrations were runoff-mediated and determined by watershed inputs and, in some cases, by internal cycling depending on hydrology and temperature. Ammonium and phosphate were relatively enriched in February-March (a transitional period from dry/cold to wet/hot climate), which can be ascribed to initial flushing runoff from human/animal waste and spring fertilizer use. A phytoplankton bloom (mainly Chlorophyta) occurred during April after a surge of water temperature, probably due to the higher availability of inorganic nutrients and sunlight and suitable hydraulic residence time (medium flow) in the transitional period. The concentration of phytoplankton was low during May-June (wet-hot climate) when the concentrations of total suspended matter (TSM) were highest, likely owing to the "shading" effect of TSM and turbulence of high flow conditions. Nutrient-algae shifts across the dry-wet season and vertical profiles suggested that algal blooms seem to be fueled primarily by phosphate and ammonium rather than nitrate. Current findings of a strong temporal pattern and the relationship between physical parameters, nutrient and biota would improve our understanding of drivers of change in water quality and ecosystem functions with dam construction.

Numerical Study on the Stomatal Responses to Dry-Hot Wind Episodes and Its Effects on Land-Atmosphere Interactions.

PubMed

Wang, Shu; Zheng, Hui; Liu, Shuhua; Miao, Yucong; Li, Jing

2016-01-01

The wheat production in midland China is under serious threat by frequent Dry-Hot Wind (DHW) episodes with high temperature, low moisture and specific wind as well as intensive heat transfer and evapotranspiration. The numerical simulations of these episodes are important for monitoring grain yield and estimating agricultural water demand. However, uncertainties still remain despite that enormous experiments and modeling studies have been conducted concerning this issue, due to either inaccurate synoptic situation derived from mesoscale weather models or unrealistic parameterizations of stomatal physiology in land surface models. Hereby, we investigated the synoptic characteristics of DHW with widely-used mesoscale model Weather Research and Forecasting (WRF) and the effects of leaf physiology on surface evapotranspiration by comparing two land surface models: The Noah land surface model, and Peking University Land Model (PKULM) with stomata processes included. Results show that the WRF model could well replicate the synoptic situations of DHW. Two types of DHW were identified: (1) prevailing heated dry wind stream forces the formation of DHW along with intense sensible heating and (2) dry adiabatic processes overflowing mountains. Under both situations, the PKULM can reasonably model the stomatal closure phenomena, which significantly decreases both evapotranspiration and net ecosystem exchange of canopy, while these phenomena cannot be resolved in the Noah simulations. Therefore, our findings suggest that the WRF-PKULM coupled method may be a more reliable tool to investigate and forecast DHW as well as be instructive to crop models.

Numerical Study on the Stomatal Responses to Dry-Hot Wind Episodes and Its Effects on Land-Atmosphere Interactions

PubMed Central

Zheng, Hui; Liu, Shuhua; Miao, Yucong; Li, Jing

2016-01-01

The wheat production in midland China is under serious threat by frequent Dry-Hot Wind (DHW) episodes with high temperature, low moisture and specific wind as well as intensive heat transfer and evapotranspiration. The numerical simulations of these episodes are important for monitoring grain yield and estimating agricultural water demand. However, uncertainties still remain despite that enormous experiments and modeling studies have been conducted concerning this issue, due to either inaccurate synoptic situation derived from mesoscale weather models or unrealistic parameterizations of stomatal physiology in land surface models. Hereby, we investigated the synoptic characteristics of DHW with widely-used mesoscale model Weather Research and Forecasting (WRF) and the effects of leaf physiology on surface evapotranspiration by comparing two land surface models: The Noah land surface model, and Peking University Land Model (PKULM) with stomata processes included. Results show that the WRF model could well replicate the synoptic situations of DHW. Two types of DHW were identified: (1) prevailing heated dry wind stream forces the formation of DHW along with intense sensible heating and (2) dry adiabatic processes overflowing mountains. Under both situations, the PKULM can reasonably model the stomatal closure phenomena, which significantly decreases both evapotranspiration and net ecosystem exchange of canopy, while these phenomena cannot be resolved in the Noah simulations. Therefore, our findings suggest that the WRF-PKULM coupled method may be a more reliable tool to investigate and forecast DHW as well as be instructive to crop models. PMID:27648943

Photosynthetic thermotolerance of woody savanna species in China is correlated with leaf life span

PubMed Central

Zhang, Jiao-Lin; Poorter, L.; Hao, Guang-You; Cao, Kun-Fang

2012-01-01

Background and Aims Photosynthetic thermotolerance (PT) is important for plant survival in tropical and sub-tropical savannas. However, little is known about thermotolerance of tropical and sub-tropical wild plants and its association with leaf phenology and persistence. Longer-lived leaves of savanna plants may experience a higher risk of heat stress. Foliar Ca is related to cell integrity of leaves under stresses. In this study it is hypothesized that (1) species with leaf flushing in the hot-dry season have greater PT than those with leaf flushing in the rainy season; and (2) PT correlates positively with leaf life span, leaf mass per unit area (LMA) and foliar Ca concentration ([Ca]) across woody savanna species. Methods The temperature-dependent increase in minimum fluorescence was measured to assess PT, together with leaf dynamics, LMA and [Ca] for a total of 24 woody species differing in leaf flushing time in a valley-type savanna in south-west China. Key Results The PT of the woody savanna species with leaf flushing in the hot-dry season was greater than that of those with leaf flushing in the rainy season. Thermotolerance was positively associated with leaf life span and [Ca] for all species irrespective of the time of flushing. The associations of PT with leaf life span and [Ca] were evolutionarily correlated. Thermotolerance was, however, independent of LMA. Conclusions Chinese savanna woody species are adapted to hot-dry habitats. However, the current maximum leaf temperature during extreme heat stress (44·3 °C) is close to the critical temperature of photosystem II (45·2 °C); future global warming may increase the risk of heat damage to the photosynthetic apparatus of Chinese savanna species. PMID:22875810

Thermal transfer in extracted incisors during thermal pulp sensitivity testing.

PubMed

Linsuwanont, P; Palamara, J E; Messer, H H

2008-03-01

To measure the temperature distribution within tooth structure during and after application of thermal stimuli used during pulp sensitivity testing. Extracted intact human maxillary anterior teeth were investigated for temperature changes at the labial enamel, the dentino-enamel junction (DEJ) and pulpal surface during and after a 5-s application of six different thermal stimuli: hot water (80 degrees C), heated gutta-percha (140 degrees C), carbon dioxide dry ice (-72 degrees C), refrigerant spray (-50 degrees C), ice stick (0 degrees C) and cold water (2 degrees C). J-type thermocouples and heat conduction paste were used to detect temperature changes, together with a data acquisition system (Labview). Data were analysed using analysis of variance, with a confidence level of P < 0.05. Temperature change was detected more quickly at the DEJ and pulpal surface with the application of hot water, heated gutta-percha and refrigerant spray than with carbon dioxide dry ice and ice (P < 0.05). Cold water and refrigerant spray were in the same range in terms of time to detect temperature change at both the DEJ and pulpal surface. Thermal stimuli with greater temperature difference from tooth temperature created a greater thermal gradient initially, followed by a greater temperature change at the DEJ and the pulpal surface. In this regard, ice and cold water were weaker stimuli than others (P < 0.05). Thermal stimuli used in pulp testing are highly variable in terms of temperature of the stimulus, rate of thermal transfer to the tooth and extent of temperature change within tooth structure. Overall, dry ice and refrigerant spray provide the most consistent stimuli, whereas heated gutta-percha and hot water were highly variable. Ice was a weak stimulus.

Linking Teleconnections and Iowa's Climate

NASA Astrophysics Data System (ADS)

Rowe, S. T.; Villarini, G.; Lavers, D. A.; Scoccimarro, E.

2013-12-01

In recent years Iowa and the U.S. Midwest has experienced both extreme drought and flood periods. With a drought in 2012 bounded by major floods in 2011 and 2013, the rapid progression from one extreme to the next is on the forefront of the public mind. Given that Iowa is a major agricultural state, extreme weather conditions can have severe socioeconomic consequences. In this research we investigate the large-scale climate processes that occurred concurrently and before a range of dry/wet and cold/hot periods to improve process understanding of these events. It is essential to understand the large-scale climate processes, as these can then provide valuable insight toward the development of long-term climate forecasts for Iowa. In this study monthly and seasonal surface temperature and precipitation over 1950-2012 across Iowa are used. Precipitation and surface temperature data are retrieved from the Parameter-elevation Regressions on Independent Slopes Model (PRISM) Climate Group at Oregon State University. The large-scale atmospheric fields are obtained from the National Center for Environmental Prediction (NCEP) / National Center for Atmospheric Research (NCAR) Reanalysis 1 Project. Precipitation is stratified according to wet, normal, and dry conditions, while temperature according to hot, average, and cold periods. Different stratification criteria based on the precipitation and temperature distributions are examined. Mean sea-level pressure and sea-surface temperature composite maps for the northern hemisphere are then produced for the wet/dry conditions, and cold/hot conditions. Further analyses include correlation, anomalies, and assessment of large-scale planetary wave activity, shedding light on the differences and similarities among the opposite weather conditions. The results of this work will highlight regional weather patterns that are related to the climate over Iowa, providing valuable insight into the mechanisms controlling the occurrence of potentially extreme weather conditions over this area.

Habitability of waterworlds: runaway greenhouses, atmospheric expansion, and multiple climate states of pure water atmospheres.

PubMed

Goldblatt, Colin

2015-05-01

There are four different stable climate states for pure water atmospheres, as might exist on so-called "waterworlds." I map these as a function of solar constant for planets ranging in size from Mars-sized to 10 Earth-mass. The states are as follows: globally ice covered (Ts ⪅ 245 K), cold and damp (270 ⪅ Ts ⪅ 290 K), hot and moist (350 ⪅ Ts ⪅ 550 K), and very hot and dry (Tsx2A86;900 K). No stable climate exists for 290 ⪅ T s ⪅ 350 K or 550 ⪅ Ts ⪅ 900 K. The union of hot moist and cold damp climates describes the liquid water habitable zone, the width and location of which depends on planet mass. At each solar constant, two or three different climate states are stable. This is a consequence of strong nonlinearities in both thermal emission and the net absorption of sunlight. Across the range of planet sizes, I account for the atmospheres expanding to high altitudes as they warm. The emitting and absorbing surfaces (optical depth of unity) move to high altitude, making their area larger than the planet surface, so more thermal radiation is emitted and more sunlight absorbed (the former dominates). The atmospheres of small planets expand more due to weaker gravity; the effective runaway greenhouse threshold is about 35 W m(-2) higher for Mars, 10 W m(-2) higher for Earth or Venus, but only a few W m(-2) higher for a 10 Earth-mass planet. There is an underlying (expansion-neglected) trend of increasing runaway greenhouse threshold with planetary size (40 W m(-2) higher for a 10 Earth-mass planet than for Mars). Summing these opposing trends means that Venus-sized (or slightly smaller) planets are most susceptible to a runaway greenhouse. The habitable zone for pure water atmospheres is very narrow, with an insolation range of 0.07 times the solar constant. A wider habitable zone requires background gas and greenhouse gas: N2 and CO2 on Earth, which are biologically controlled. Thus, habitability depends on inhabitance.

Forest response to heat waves at the dry timberline

NASA Astrophysics Data System (ADS)

Yakir, D.; Rotenberg, E.; Tatrinov, F.; Ogee, J.; Maseyk, K.

2012-04-01

Predictions of climate change consistently indicate continuous warming and drying for the entire Mediterranean basin and other regions during the next century. Investigating forest functioning at the current dry and hot "timberline" has therefore implications for predicting future forest distribution. In such investigations we should consider the forest adjustments to extreme conditions both at the long-term average climate basis, as at the time-scale of episodic extreme events, such as heat waves and droughts. Investigating both aspects in a 45-yr old semi-arid pine forest at the dry timberline (<300 mm annual rainfall) we observe adjustments that improve carbon-, nitrogen- and water- use efficiencies. An important aspect in the ecosystem sustainability is its ability to rapidly recover from extreme conditions, both at the short-term and the seasonal scale. A remarkable example is provided by the episodes (usually 2-4 days) of Easterly dry and hot air that are common in spring (so-called "Hamsin" events). During these events air temperature increases and relative humidity decreases within hours by 10˚C and 40%, respectively. Net ecosystem CO2 exchange (NEE) and photosynthesis (GPP) sharply decline, predominantly in response to the drastic increase in vapor pressure deficit (up to 6kPa), but then show full recovery to the pre-stress values within 24 h past the event. Similarly, following 5-6 months of seasonal drought, the forest resumes high photosynthetic activity within ~5 days following the first rain episode of about 10 mm in the fall. We show that these transient responses are useful in partitioning between the ecosystem responses to short-term atmosphere-driven stress and longer-term soil moisture stress. An ecosystem model (MuSICA) was used to test our understandings of underlying processes, and our ability to account for such differential responses.

Design of Tomato Drying System by Utilizing Brine Geothermal

NASA Astrophysics Data System (ADS)

Afuar, W.; Sibarani, B.; Abdurrahman, G.; Hendrarsakti, J.

2016-09-01

Cultivation of tomato plants in Indonesia has been started since 1961.Tomatoes generally will rot in three days if left on storage. Moreover, low quality tomatoes have cheaper price. After harvested, tomatoes need to be treated by drying process so it can last longer. Energy for drying tomatoes can be obtained by utilizing heat from geothermal brine. Purpose of this research is to design a tomato drying system by extracting heat of geothermal brine from separator with certain flow rate to heat up water by using a heat exchanger. Furthermore, this water will be used to heat up the surrounding air which is circulated by blower system to heat up the tomatoes chamber. Tomatoes drying process needs temperature range of 50-70°C to evaporate water content from 95.7% to 26%. After that treatment, the tomatoes are expected to have better durability. The objective of this study is to determine the quantity of hot brine which is needed for drying tomatoes and to design a drying system so that tomatoes can last longer.

Startup of air-cooled condensers and dry cooling towers at low temperatures of the cooling air

NASA Astrophysics Data System (ADS)

Milman, O. O.; Ptakhin, A. V.; Kondratev, A. V.; Shifrin, B. A.; Yankov, G. G.

2016-05-01

The problems of startup and performance of air-cooled condensers (ACC) and dry cooling towers (DCT) at low cooling air temperatures are considered. Effects of the startup of the ACC at sub-zero temperatures are described. Different options of the ACC heating up are analyzed, and examples of existing technologies are presented (electric heating, heating up with hot air or steam, and internal and external heating). The use of additional heat exchanging sections, steam tracers, in the DCT design is described. The need for high power in cases of electric heating and heating up with hot air is noted. An experimental stand for research and testing of the ACC startup at low temperatures is described. The design of the three-pass ACC unit is given, and its advantages over classical single-pass design at low temperatures are listed. The formation of ice plugs inside the heat exchanging tubes during the start-up of ACC and DCT at low cooling air temperatures is analyzed. Experimental data on the effect of the steam flow rate, steam nozzle distance from the heat-exchange surface, and their orientation in space on the metal temperature were collected, and test results are analyzed. It is noted that the surface temperature at the end of the heat up is almost independent from its initial temperature. Recommendations for the safe start-up of ACCs and DCTs are given. The heating flow necessary to sufficiently heat up heat-exchange surfaces of ACCs and DCTs for the safe startup is estimated. The technology and the process of the heat up of the ACC with the heating steam external supply are described by the example of the startup of the full-scale section of the ACC at sub-zero temperatures of the cooling air, and the advantages of the proposed start-up technology are confirmed.

Forming Hot Jupiters: Observational Constraints on Gas Giant Formation and migration

NASA Astrophysics Data System (ADS)

Becker, Juliette; Vanderburg, Andrew; Adams, Fred C.; Khain, Tali; Bryan, Marta

2018-04-01

Since the first extrasolar planets were detected, the existence of hot Jupiters has challenged prevailing theories of planet formation. The three commonly considered pathways for hot Jupiter formation are in situ formation, runaway accretion in the outer disk followed by disk migration, and tidal migration (occurring after the disk has dissipated). None of these explains the entire observed sample of hot Jupiters, suggesting that different selections of systems form via different pathways. The way forward is to use observational data to constrain the migration pathways of particular classes of systems, and subsequently assemble these results into a coherent picture of hot Jupiter formation. We present constraints on the migratory pathway for one particular type of system: hot Jupiters orbiting cool stars (T< 6200 K). Using the full observational sample, we find that the orbits of most wide planetary companions to hot Jupiters around these cool stars must be well aligned with the orbits of the hot Jupiters and the spins of the host stars. The population of systems containing both a hot Jupiter and an exterior companion around a cool star thus generally exist in roughly coplanar configurations, consistent with the idea that disk-driven migratory mechanisms have assembled most of this class of systems. We then discuss the overall applicability of this result to a wider range of systems and the broader implications on planet formation.

Effect of drying conditions on drying kinetics and quality of aromatic Pandanus amaryllifolius leaves.

PubMed

Rayaguru, Kalpana; Routray, Winny

2010-12-01

Pandanus amaryllifolius is a plant with aromatic leaves, which impart the characteristic flavour of aromatic rice. The quality of aromatic Pandanus leaves dried at low temperature (35 °C) and low RH (27%) in a heat pump dryer was evaluated and compared with those obtained from hot air drying at 45 °C. Thin-layer drying kinetics has been studied for both the conditions. To determine the kinetic parameters, the drying data were fitted to various semi-theoretical models. The goodness of fit was determined using the coefficient of determination, reduced chi square, and root mean square error. Aroma, colour, and overall acceptability determination of fresh and dried leaves were made using sensory evaluation. Drying of leaves took place mainly under the falling-rate period. The Page equation was found to be best among the proposed models to describe the thin-layer drying of Pandanus leaves with higher coefficient of determination. The effective moisture diffusivity values were also determined. The effect of low RH was prominent during the initial drying when the product was moist. The effect of temperature was prominent in the later part of drying, which acted as a driving force for moisture diffusion and hence the total drying time was reduced. Retention of aromatic compound 2-acetyl-1-pyrroline content was more in low temperature dried samples with higher sensory scores.

29 CFR 1917.152 - Welding, cutting and heating (hot work) 12 (See also § 1917.2, definition of Hazardous cargo...

Code of Federal Regulations, 2010 CFR

2010-07-01

... thoroughly dry before welding is performed on them. (ii) Employees in areas not protected from the arc by... against radiant energy. (1) Employees shall be protected from radiant energy eye hazards by spectacles...

Chemical milling solution reveals stress corrosion cracks in titanium alloy

NASA Technical Reports Server (NTRS)

Braski, D. N.

1967-01-01

Solution of hydrogen flouride, hydrogen peroxide, and water reveals hot salt stress corrosion cracks in various titanium alloys. After the surface is rinsed in water, dried, and swabbed with the solution, it can be observed by the naked eye or at low magnification.

Analgesic properties of Capraria biflora leaves aqueous extract.

PubMed

Acosta, S L; Muro, L V; Sacerio, A L; Peña, A R; Okwei, S N

2003-12-01

The analgesic properties of dried leaves of Capraria biflora were investigated. The aqueous extract (50-200 mg kg(-1)) produced moderate inhibition of acetic acid-induced writhing in mice. At the same doses, a better analgesic effect was observed on the hot plate test.

Builders Challenge High Performance Builder Spotlight - Artistic Homes, Albuquerque, NM

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

2009-01-01

Building America Builders Challenge fact sheet on Artistic Homes of Albuquerque, New Mexico. Describes the first true zero E-scale home in a hot-dry climate with ducts inside, R-50 attic insulation, roof-mounted photovoltaic power system, and solar thermal water heating.

Preliminary investigation of two areas in New York State in terms of possible potential for hot dry rock geothermal energy. [Adirondack Mountains and Catskill Mountains

DOE Office of Scientific and Technical Information (OSTI.GOV)

Isachsen, Y.W.

1978-09-27

Two areas in New York State were studied in terms of possible long range potential for geothermal energy: the Adirondack Mountains which are undergoing contemporary doming, and an anomalous circular feature centered on Panther Mountain in the Catskill Mountains. The Adirondack Mountains constitute an anomalously large, domical uplift on the Appalachian foreland. The domical configuration of the area undergoing uplift, combined with subsidence at the northeastern perimeter of the dome, argues for a geothermal rather than glacioisostatic origin. A contemporary hot spot near the crust-mantle boundary is proposed as the mechanism of doming, based on analogy with uplifts of similarmore » dimensions elsewhere in the world, some of which have associated Tertiary volcanics. The lack of thermal springs in the area, or high heat flow in drill holes up to 370 m deep, indicates that the front of the inferred thermal pulse must be at some depth greater than 1 km. From isopach maps by Rickard (1969, 1973), it is clear that the present Adirondack dome did not come into existence until sometime after Late Devonian time. Strata younger than this are not present to provide further time stratigraphic refinement of this lower limit. However, the consequent radial drainage pattern in the Adirondacks suggests that the dome is a relatively young tectonic feature. Using arguments based on fixed hot spots in central Africa, and the movement of North American plate, Kevin Burke (Appendix I) suggests that the uplift may be less than 4 m.y. old.The other area of interest, the Panther Mountain circular feature in the Catskill Mountains, was studied using photogeology, gravity and magnetic profiling, gravity modeling, conventional field methods, and local shallow seismic refraction profiling.« less

Development of high Tc (greater than 100 K) Bi, Tl and Y-based materials as superconducting circuit elements

NASA Technical Reports Server (NTRS)

Haertling, Gene; Grabert, Gregory; Gilmour, Phillip

1994-01-01

Experimental work on this project over the last four years has resulted in establishing processing and characterization techniques for producing both the Bi-based and Tl-based superconductors in their high temperature (2223) forms. In the bulk, dry pressed form, maximum critical temperatures (Tc) of 108.2 K and 117.8 K, respectively, were measured. Results have further shown that the Bi and Tl-based superconducting materials in bulk form are noticeably different from the Y-based 123 material in that superconductivity is considerably harder to achieve, maintain, and reproduce. This is due primarily to the difficulty in obtaining the higher Tc phase in pure form since it commonly co-exists with other undesirable, lower Tc phases. In particular, it has been found that long processing times for calcining and firing (20 - 200 hrs.) and close control of temperatures which are very near the melting point are required in order to obtain higher proportions of the desirable, high Tc (2223) phase. Thus far, the BSCCO bulk materials has been prepared in uniaxially pressed, hot pressed, and tapecast form. The uniaxially pressed material has been synthesized by the mixed oxide, coprecipitation, and melt quenching processes. The tapecast and hot pressed materials have been prepared via the mixed oxide process. In addition, thick films of BSCCO (2223 phase) have been prepared by screen printing on to yttria and magnesia stabilized zirconia with only moderate success; i.e., superconductivity was achieved in these thick films, but the highest Tc obtained in these films was 89.0 K. The Tc's of the bulk hot pressed, tapecast, and screen printed thick film materials were found to be 108.2, 102.4, and 89.0 K, respectively.

Unprecedented climate events: Historical changes, aspirational targets, and national commitments

PubMed Central

Diffenbaugh, Noah S.; Singh, Deepti; Mankin, Justin S.

2018-01-01

The United Nations Paris Agreement creates a specific need to compare consequences of cumulative emissions for pledged national commitments and aspirational targets of 1.5° to 2°C global warming. We find that humans have already increased the probability of historically unprecedented hot, warm, wet, and dry extremes, including over 50 to 90% of North America, Europe, and East Asia. Emissions consistent with national commitments are likely to cause substantial and widespread additional increases, including more than fivefold for warmest night over ~50% of Europe and >25% of East Asia and more than threefold for wettest days over >35% of North America, Europe, and East Asia. In contrast, meeting aspirational targets to keep global warming below 2°C reduces the area experiencing more than threefold increases to <10% of most regions studied. However, large areas—including >90% of North America, Europe, East Asia, and much of the tropics—still exhibit sizable increases in the probability of record-setting hot, wet, and/or dry events. PMID:29457133

Numerical study of the vertical shading devices effect on the thermal performance of promotional apartments in hot dry climate of Algeria

NASA Astrophysics Data System (ADS)

Berkouk, Djihed; Bouzir, Tallal Abdel Karim; Mazouz, Said

2018-05-01

The bioclimatic architecture considers the local climatic conditions in order to reconcile maximally the comfort condition of the occupants. Through the several simulations effectuated by the TRNSYS software, this paper shows that the new architecture produced in the south of Algeria following the northern cities tendency is not fully adapted to the hot dry climate of the southern regions, such as the city of Biskra. In these regions, the passive techniques design influence strongly on the thermal architectural space performance. In this regard, diverse of the vertical shading devices size were proposed to evaluate the impact of this passive technique on the thermal performance of the promotional apartments situated in the city of Biskra. The comparative analysis between the simulation results says that the effectiveness of the vertical shading devices on the thermal performance spaces is reducing the indoor air temperature during the summer period. In addition, this analysis shows that promotional apartments are unsuitable for the desert climate.

Hot Dry Rock Geothermal Energy Development Program: Annual report, fiscal year 1985

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brown, D.W.; Franke, P.R.; Smith, M.C.

1987-01-01

The primary objective for the Hot Dry Rock Program at the Los Alamos National Laboratory during fiscal year 1985 was to complete the Phase 2 reservoir connection and to begin flow testing the resulting reservoir. The connection was achieved through redrilling one well and additional fracturing operations, and progress was made toward developing a detailed understanding of the fractured region through a variety of reservoir interrogation methods. Other accomplishments during the fiscal year included improvement of the high-temperature, inflatable, open-hole packer used to isolate sections of the uncased wellbore in collaboration with the Baker Corporation and the design and fabricationmore » of a high-temperature borehole acoustic televiewer in a cooperative program with a research institute in West Germany. Progress was also made in techniques for the collection and analysis of microseismic data. Reservoir-engineering activities and geochemical studies, as well as the more routine support activities, continued in FY85. 18 refs., 15 figs.« less

The Effect of Fabric Type of Common Iranian Working Clothes on the Induced Cardiac and Physiological Strain Under Heat Stress.

PubMed

Parvari, Roh Allah; Aghaei, Habib Allah; Dehghan, Habibollah; Khademi, Abolfazl; Maracy, Mohammad Reza; Dehghan, Somayeh Farhang

2015-01-01

The present study compared the effect of fabric type of working clothes on heat strain responses in different levels of physical workload and under different kinds of weather conditions. Four kinds of working clothing fabric that are greatly popular in Iranian industry were assessed on 18 healthy male at 2 environments: hot and humid (dry temperature [DBt]: 35°C and relative humidity [RH]: 70%) and hot and dry (DBt: 40°C and RH: 40%). The physiological responses such as heart rate and core body temperature were reported. It was found that there were no significant differences between different types of clothing fabric on cardiac and physiological parameters. It can be recommended that 100% cotton clothing ensemble during low-workload activities and 30.2% cotton-69.8% polyester clothing ensemble during moderate-workload activities is used for Iranian workers to maintain the cardiac and physiological strains as low as possible.

Comparison study on biosynthesis of silver nanoparticles using fresh and hot air oven dried IMPERATA CYLINDRICA leaf

NASA Astrophysics Data System (ADS)

Najmi Bonnia, Noor; Fairuzi, Afiza Ahmad; Akhir, Rabiatuladawiyah Md.; Yahya, Sabrina M.; Rani, Mohd Azri Ab; Ratim, Suzana; Rahman, Norafifah A.; Akil, Hazizan Md

2018-01-01

The perennial rhizomatous grass; Imperata cylindrica (I. cylindrica) has been reported rich in various phytochemicals. In present study, silver nanoparticles were synthesized from aqueous leaf extract of I. cylindrica at two different leaf conditions; fresh leaves and hot-air oven dried leaves. Biosynthesized silver nanoparticles were characterized by UV-visible spectroscopy, field emission scanning electron microscopy (FESEM) and Fourier transform infrared spectroscopy (FTIR). Maximum absorption was recorded between 400 nm to 500 nm. FESEM analysis revealed that the silver nanoparticles predominantly form spherical shapes. The particles sizes were ranging from 22-37 nm. The elemental composition of the synthesized silver nanoparticles was confirmed by using energy dispersive X-ray spectroscopy (EDX) analysis. Fourier transform infrared spectroscopy (FTIR) confirmed the reducing and stabilizing actions came from biomolecules associated with I. cylindrica leaf extract. Thus in this investigation, an environmentally safe method to synthesized silver nanoparticles using local plant extract was successfully established.

Unprecedented climate events: Historical changes, aspirational targets, and national commitments.

PubMed

Diffenbaugh, Noah S; Singh, Deepti; Mankin, Justin S

2018-02-01

The United Nations Paris Agreement creates a specific need to compare consequences of cumulative emissions for pledged national commitments and aspirational targets of 1.5° to 2°C global warming. We find that humans have already increased the probability of historically unprecedented hot, warm, wet, and dry extremes, including over 50 to 90% of North America, Europe, and East Asia. Emissions consistent with national commitments are likely to cause substantial and widespread additional increases, including more than fivefold for warmest night over ~50% of Europe and >25% of East Asia and more than threefold for wettest days over >35% of North America, Europe, and East Asia. In contrast, meeting aspirational targets to keep global warming below 2°C reduces the area experiencing more than threefold increases to <10% of most regions studied. However, large areas-including >90% of North America, Europe, East Asia, and much of the tropics-still exhibit sizable increases in the probability of record-setting hot, wet, and/or dry events.

Highly Attrition Resistant Zinc Oxide-Based Sorbents for H2S Removal by Spray Drying Technique

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ryu, C.K.; Lee, J.B.; Ahn, D.H.

2002-09-19

Primary issues for the fluidized-bed/transport reactor process are high attrition resistant sorbent, its high sorption capacity and regenerability, durability, and cost. The overall objective of this project is the development of a superior attrition resistant zinc oxide-based sorbent for hot gas cleanup in integrated coal gasification combined cycle (IGCC). Sorbents applicable to a fluidized-bed hot gas desulfurization process must have a high attrition resistance to withstand the fast solid circulation between a desulfurizer and a regenerator, fast kinetic reactions, and high sulfur sorption capacity. The oxidative regeneration of zinc-based sorbent usually initiated at greater than 600 C with highly exothermicmore » nature causing deactivation of sorbent as well as complication of sulfidation process by side reaction. Focusing on solving the sorbent attrition and regenerability of zinc oxide-based sorbent, we have adapted multi-binder matrices and direct incorporation of regeneration promoter. The sorbent forming was done with a spray drying technique that is easily scalable to commercial quantity.« less

Inhibitory effect of hot-water extract from dried fruit of Crataegus pinnatifida on low-density lipoprotein (LDL) oxidation in cell and cell-free systems.

PubMed

Chu, Chia-Yih; Lee, Miao-Jane; Liao, Chuen-Lan; Lin, Wea-Lung; Yin, Yu-Fang; Tseng, Tsui-Hwa

2003-12-17

The dried fruit of Crataegus pinnatifida, a local soft drink material and medical herb, was found to possess potential against oxidative stress. In the preliminary study, the antioxidant potential of a hot-water extract obtained from the dried fruit of C. pinnatifida (CF-H) was evaluated in terms of its capacity of quenching 1,1-diphenyl-2-picrylhydrazyl free radicals (EC(50) = 0.118 mg/mL). After content analysis, it was found that CF-H is mainly composed of polyphenols including flavonoids (6.9%), procyanidins (2.2%), (+)-catechin (0.5%), and (-)-epicatechin (0.2%). The antioxidative bioactivity of CF-H had been assess previously using the models of CuSO(4) as cell-free system and sodium nitroprusside (SNP) plus macrophage RAW 264.7 cells as cell system to induce human low-density lipoprotein oxidation. CF-H was found to inhibit relative electrophoretic mobility and thiobarbituric acid reactive substances at the concentration of 0.5-1.0 mg/mL in the cell-free system and at 0.01-0.10 mg/mL in the cell system. Furthermore, it was found that CF-H decreased the SNP-induced cell lipid peroxidation and reduced glutathione depletion.

Dispersal, isolation and diversification with continued gene flow in an Andean tropical dry forest.

PubMed

Toby Pennington, R; Lavin, Matt

2017-07-01

The Andes are the world's longest mountain chain, and the tropical Andes are the world's richest biodiversity hot spot. The origin of the tropical Andean cordillera is relatively recent because the elevation of the mountains was relatively low (400-2500 m palaeoelevations) only 10 MYA with final uplift being rapid. These final phases of the Andean orogeny are thought to have had a fundamental role in shaping processes of biotic diversification and biogeography, with these effects reaching far from the mountains themselves by changing the course of rivers and deposition of mineral-rich Andean sediments across the massive Amazon basin. In a recent issue of Molecular Ecology, Oswald, Overcast, Mauck, Andersen, and Smith (2017) investigate the biogeography and diversification of bird species in the Andes of Peru and Ecuador. Their study is novel in its focus on tropical dry forests (Figure 1) rather than more mesic biomes such as rain forests, cloud forests and paramos, which tend to be the focus of science and conservation in the Andean hot spot. It is also able to draw powerful conclusions via the first deployment of genomic approaches to a biogeographic question in the threatened dry forests of the New World. © 2017 John Wiley & Sons Ltd.

Motel solar-hot-water system with nonpressurized storage--Jacksonville, Florida

NASA Technical Reports Server (NTRS)

1981-01-01

Modular roof-mounted copper-plated arrays collect solar energy; heated water drains from them into 1,000 gallon nonpressurized storage tank which supplies energy to existing pressurized motel hot water lines. System provides 65 percent of hot water demand. Report described systems parts and operation, maintenance, and performance and provides warranty information.

Development of Defoamers for Confinenment Foam

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hoffman, D M; Mitchell, A R

Aqueous foam concentrate (AFC) 380 foam was developed by Sandia National Laboratory as a blast mitigation foam for unexploded ordnance (UXO) and its ''engineered foam structure'' is reported to be able to ''envelop chemical or biological aerosols'' [1]. It is similar to commercial fire-fighting foams, consisting mostly of water with small amounts of two alcohols, an ether and surfactant. It also contains xanthan gum, probably, to strengthen the foam film and delay drainage. The concentrate is normally diluted in a 6:94 ratio with water for foaming applications. The diluted solution is normally foamed with air to an expansion factor ofmore » about 100 (density 0.01 g/cc), which is called ''dry'' foam. Higher density foam (0.18 > {rho} > 0.03 g/cc) was discovered which had quite different characteristics from ''dry'' foam and was called ''wet'' foam. Some characterization of these foams has also been carried out, but the major effort described in this document is the evaluation, at the small and medium scale, of chemical, mechanical and thermal approaches to defoaming AFC 380 foam. Several chemical approaches to defoaming were evaluated including oxidation and precipitation of the xanthan, use of commercial oil-emulsion or suspension defoamers, pH modification, and cation exchange with the surfactant. Of these the commercial defoamers were most effective. Two mechanical approaches to defoaming were evaluated: pressure and foam rupture with very fine particles. Pressure and vacuum techniques were considered too difficult for field applications but high surface area silica particles worked very well on dry foam. Finally simple thermal techniques were evaluated. An order-disorder transition occurs in xanthan solutions at about 60 C, which may be responsible for the effectiveness of hot air as a defoamer. During defoaming of 55 gallons of foam with hot air, after about 70% of the AFC 380 foam had been defoamed, the effectiveness of hot air was dramatically reduced. Approximately 15 gal of residual foam containing mostly small bubbles was resistant to further defoaming by methods that had been effective on the original, dry foam. In this paper the residual foam is referred to as ''wet'' and the original foam is referred to as ''dry''. Methods for generating ''wet'' foam in small to moderate quantities for defoaming experiments have been developed. Methods for defoaming wet foam are currently under study.« less

Numerical Investigation of Novel Oxygen Blast Furnace Ironmaking Processes

NASA Astrophysics Data System (ADS)

Li, Zhaoyang; Kuang, Shibo; Yu, Aibing; Gao, Jianjun; Qi, Yuanhong; Yan, Dingliu; Li, Yuntao; Mao, Xiaoming

2018-04-01

Oxygen blast furnace (OBF) ironmaking process has the potential to realize "zero carbon footprint" production, but suffers from the "thermal shortage" problem. This paper presents three novel OBF processes, featured by belly injection of reformed coke oven gas, burden hot-charge operation, and their combination, respectively. These processes were studied by a multifluid process model. The applicability of the model was confirmed by comparing the numerical results against the measured key performance indicators of an experimental OBF operated with or without injection of reformed coke oven gas. Then, these different OBF processes together with a pure OBF were numerically examined in aspects of in-furnace states and global performance, assuming that the burden quality can be maintained during the hot-charge operation. The numerical results show that under the present conditions, belly injection and hot charge, as auxiliary measures, are useful for reducing the fuel rate and increasing the productivity for OBFs but in different manners. Hot charge should be more suitable for OBFs of different sizes because it improves the thermochemical states throughout the dry zone rather than within a narrow region in the case of belly injection. The simultaneous application of belly injection and hot charge leads to the best process performance, at the same time, lowering down hot-charge temperature to achieve the same carbon consumption and hot metal temperature as that achieved when applying the hot charge alone. This feature will be practically beneficial in the application of hot-charge operation. In addition, a systematic study of hot-charge temperature reveals that optimal hot-charge temperatures can be identified according to the utilization efficiency of the sensible heat of hot burden.

Summer Indoor Heat Pump Water Heater Evaluation in a Hot-Dry Climate

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hoeschele, Marc; Seitzler, Matthew

Heat pump water heaters offer a significant opportunity to improve water heating performance for the over 40% of U.S. households that heat domestic hot water using electric resistance storage water heaters. Numerous field studies have also been completed documenting performance in a variety of climates and applications. More recent evaluation efforts have focused attention on the performance of May through September 2014, with ongoing winter monitoring being sponsored by California utility partners. Summer results show favorable system performance with extrapolated annual water heating savings of 1,466 to 2,300 kWh per year, based on the observed hot water loads. Additional summermore » space cooling benefits savings of 121 to 135 kWh per year were projected, further increasing the water energy savings.« less

Summer Indoor Heat Pump Water Heater Evaluation in a Hot-Dry Climate

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hoeschele, Marc; Seitzler, Matthew

2017-05-01

Heat pump water heaters offer a significant opportunity to improve water heating performance for the over 40% of U.S. households that heat domestic hot water using electric resistance storage water heaters. Numerous field studies have also been completed documenting performance in a variety of climates and applications. More recent evaluation efforts have focused attention on the performance of May through September 2014, with ongoing winter monitoring being sponsored by California utility partners. Summer results show favorable system performance with extrapolated annual water heating savings of 1,466 to 2,300 kWh per year, based on the observed hot water loads. Additional summermore » space cooling benefits savings of 121 to 135 kWh per year were projected, further increasing the water energy savings.« less

Enhancement of drying and rehydration characteristics of okra by ultrasound pre-treatment application

NASA Astrophysics Data System (ADS)

Tüfekçi, Senem; Özkal, Sami Gökhan

2017-07-01

Effect of ultrasound application prior to hot air drying on drying and rehydration kinetics, rehydration ratio and microstructure of okra slices were investigated. For this purpose, the selected parameters are ultrasound pre-treatment time (10, 20 and 30 min), ultrasound amplitude (55 and 100%) and the temperature of drying air (60 and 70 °C). 5 mm thick cylindrical shaped okra slices were used in the experiments. The samples were immersed in water and ultrasonic pre-treatments were done in water with ultrasonic probe connected to an ultrasonic generator with 20 kHz frequency. Pre-treated samples were dried in a tray drier with a 0.3 m/s air velocity. Ultrasound pre-treatment affected the drying rate of the okra slices significantly. Drying time of okra slices was decreased by the application of ultrasound pre-treatment. Modified Page model found to be the most suitable model for describing the drying characteristics of okra slices. Improvements in rehydration properties of the dried samples were observed due to the ultrasound pre-treatment. The influence of the ultrasound pre-treatment on microstructure was clearly observed through scanning electron microscopy images of the dried samples. As the amplitude of ultrasound increased the changes in structure of the okra tissue increased.

The role of sediments stored in valleys in modulating the Quaternary weathering flux variations

NASA Astrophysics Data System (ADS)

Carretier, Sebastien; Goddéris, Yves; Vigier, Nathalie; Maffre, Pierre

2017-04-01

Silicate weathering is known to be central to the regulation of atmospheric CO2. Yet it is unclear how weathering responds to climatic variations. Data sets based on different proxies in sediment cores suggest either negligible Quaternary silicate weathering variations, or more weathering during wet and hot periods, or even the reverse. For example, a recent study based on d7Li in clay of Himalayan river terraces suggests, counter-intuitively, a less intense weathering during hot and wet periods compared to dry periods for the last 40 ka, with no clear physical explanation. We analyse catchment scale weathering signals using the numerical model Cidre, coupling landscape evolution with chemical weathering. Chemical weathering occurs within a regolith, either produced in situ at a rate depending on regolith thickness, temperature and precipitation, or corresponding to a deposit. The chemical flux is calculated from the dissolution of granitoid clasts, first exhumed on the hillslopes and then transported and potentially stocked in the valleys. This approach accounts for part of the stochastic nature of grain weathering within a catchment. We prescribe an uplift to an initial horizontal surface to reach a dynamic equilibrium under a constant climate. Then, we vary the precipitation rate and the temperature, alternating cold and dry periods with hot and wet periods (10 to 400 ka tested). When these variations are applied to an equilibrium mountain covered by a regolith ("transport-limited"), the weathering outlfux and the erosion flux are larger during wet and hot periods. On the contrary, for less weatherable conditions such that the mountain is not covered by regolith ("kinetically-limited"), the weathering is the highest at the beginning of the dry, cold and low erosive periods. This apparent paradox is explained by the temporary accumulation of sediment in the valleys in response to the drought. The hillslopes being striped, these valley deposits constitute the only weathering reservoir, whose large volume compensates for the unfavourable climatic conditions. Such a behaviour explains out-of-phase weathering signals, and suggests that the dominant weathering reservoir goes back and forth between the hillslopes and the valleys during climatic oscillations.

The effective management of atopic dermatitis in school-age children.

PubMed

Ward, Sue

The terms atopic eczema and atopic dermatitis (AD) are synonymous. In this article, the latter term is used. AD can affect all age groups but is most commonly associated with children. It is a dry-skin condition, the severity of which can vary from person to person. It is not contagious. In mild forms of the condition the skin is dry, hot and itchy, while in more severe cases the skin can be broken, raw and bleeding, or produce vesicles and papules that may become eroded.

Mathematical Simulation of Drying Process of Fibrous Material

NASA Astrophysics Data System (ADS)

Blejchař, Tomáš; Raška, Jiří; Jablonská, Jana

2018-06-01

The article describes mathematical simulation of flowing air through porous zone and water vaporisation from mentioned porous area which actually represents dried fibrous material - cotton towel. Simulation is based on finite volume method. Wet towel is placed in pipe and hot air flow through the towel. Water from towel is evaporated. Simulation of airflow through porous element is described first. Eulerian multiphase model is then used for simulation of water vaporisation from porous medium. Results of simulation are compared with experiment. Ansys Fluent 13.0 was used for calculation.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Viklund, H.I.; Kennedy, R.H.

Uranium precipitates obtained from Congo leach liquors by an ion exchange process contained more than 0.1% chloride. Attempts were made to reduce the chloride content of typical precipitates by calcination of dried precipitate, releaching of dried precipitate with water, and washing of wet precipitate with water. Washing of wet precipitate with an aqueous solution of 0.25% Na/sub 2/SO/ sub 4/, to prevent peptization, provided a simple solution to the problem. Precipitation tests on Congo ion exchange eluates showed a marked advantage in subsequent thickening and filtration operations for precipitation from hot solution. (auth)

Study of the optimisation of puffing characteristics of potato cubes by spouted bed drying enhanced with microwave.

PubMed

Yan, Wei-qiang; Zhang, Min; Huang, Lue-lue; Tang, Juming; Mujumdar, Arun S; Sun, Jin-cai

2010-06-01

In commercial deep-fat frying of potato chips, the oil content of the final products ranges from 35 to 45 g 100 g(-1) (wet basis). High-temperature frying may cause the formation of acrylamide, making the products unhealthy to the consumer. The aim of this research was to explore a new method, spouted bed microwave drying, to produce healthier puffed snack potato cubes as possible alternatives to oil-fried potato chips. The influence of drying conditions of the spouted bed microwave drying on puffing characteristics of potato cubes were studied and compared with the direct microwave and hot air drying method. Tandem combination drying of microwave-enhanced spouted bed drying (MWSB) could achieve a good expansion ratio, breaking force and rehydration ratio. The puffing characteristics of potato cubes were significantly affected (P < 0.05) by moisture content before starting microwave power in spouted bed microwave drying, by microwave (MW) power, and by the original size of potato cubes. The optimum processing parameters were the moisture content at the start of microwave power (60%), the size of potato cubes (10-12 mm), and microwave power (2-2.5 W g(-1)) Copyright (c) 2010 Society of Chemical Industry.

Hybrid response surface methodology-artificial neural network optimization of drying process of banana slices in a forced convective dryer.

PubMed

Taheri-Garavand, Amin; Karimi, Fatemeh; Karimi, Mahmoud; Lotfi, Valiullah; Khoobbakht, Golmohammad

2018-06-01

The aim of the study is to fit models for predicting surfaces using the response surface methodology and the artificial neural network to optimize for obtaining the maximum acceptability using desirability functions methodology in a hot air drying process of banana slices. The drying air temperature, air velocity, and drying time were chosen as independent factors and moisture content, drying rate, energy efficiency, and exergy efficiency were dependent variables or responses in the mentioned drying process. A rotatable central composite design as an adequate method was used to develop models for the responses in the response surface methodology. Moreover, isoresponse contour plots were useful to predict the results by performing only a limited set of experiments. The optimum operating conditions obtained from the artificial neural network models were moisture content 0.14 g/g, drying rate 1.03 g water/g h, energy efficiency 0.61, and exergy efficiency 0.91, when the air temperature, air velocity, and drying time values were equal to -0.42 (74.2 ℃), 1.00 (1.50 m/s), and -0.17 (2.50 h) in the coded units, respectively.

Identification and future description of warming signatures over Pakistan with special emphasis on evolution of CO2 levels and temperature during the first decade of the twenty-first century.

PubMed

Haider, Khadija; Khokhar, Muhammad Fahim; Chishtie, Farrukh; RazzaqKhan, Waseem; Hakeem, Khalid Rehman

2017-03-01

Like other developing countries, Pakistan is also facing changes in temperature per decade and other climatic abnormalities like droughts and torrential rains. In order to assess and identify the extent of temperature change over Pakistan, the whole Pakistan was divided into five climatic zones ranging from very cold to hot and dry climates. Similarly, seasons in Pakistan are defined on the basis of monsoon variability as winter, pre-monsoon, monsoon, and post-monsoon. This study primarily focuses on the comparison of surface temperature observations from Pakistan Meteorological Department (PMD) network with PRECIS (Providing Regional Climates for Impacts Studies) model simulations. Results indicate that PRECIS underestimates the temperature in Northern Pakistan and during the winter season. However, there exists a fair agreement between PRECIS output and observed datasets in the lower plain and hot areas of the country. An absolute increase of 0.07 °C is observed in the mean temperature over Pakistan during the time period of 1951-2010. Especially, the increase is more significant (0.7 °C) during the last 14 years (1997-2010). Moreover, SCIAMACHY observations were used to explore the evolution of atmospheric CO 2 levels in comparison to temperature over Pakistan. CO 2 levels have shown an increasing trend during the first decade of the twenty-first century.

Effect of Drying Temperature on Rosmarinic Acid and Sinensetin Concentration in Orthosiphon stamineus Herbal Leaves

NASA Astrophysics Data System (ADS)

Abdullah, Sriyana; Razak Shaari, Abdul; Hajar Rukunudin, Ibni; Syarhabil Ahmad, Muhammad

2018-03-01

The objective of this work was to investigate the effects of drying temperature on the concentration of O rthosiphon stamineus biomarker compounds which were rosmarinic acid (RA) and sinensetin (SEN). The thin layer drying approach was used to dry O. stamineus leaves at various temperatures of 30, 40 and 50°C using a laboratory scale hot air dryer. The dried leaves were then extracted using 60% aqueous methanol prior to quantification. The RA and SEN concentrations in the dried leaves extracts were quantified by the high performance liquid chromatography. The concentration of RA for the dried leaves at 30 and 40°C were higher as compared to that of the fresh leaves. This may due to the response of the plant cells to abiotic stress. The concentration of RA also showed a significant reduction when the temperature was increased to 50°C. In contrast, the SEN concentration in O. stamineus dried leaf extract was lower than that of the fresh samples. The concentrations of SEN depicted insignificant effects by drying at 30 and 50°C, and the highest value was obtained in the samples dried at 40°C. Results showed that the drying process was found to affect the concentration of both compounds; therefore suitable drying conditions should be adopted to enhance the medicinal values of the plant species.

Support services relating to geothermal programs. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1981-08-01

Activities designed to assist in the assessment of processes through which geopressured methane production and geopressure-geothermal power can be increased are discussed. Progress is reported on the following: general support, hot-dry-rock review, R and D plan, and the Edna Delcambre final report. (MHR)

7 CFR 319.40-7 - Treatments and safeguards.

Code of Federal Regulations, 2010 CFR

2010-01-01

... any other method (e.g., the hot water and steam techniques used in veneer production) that raises the... the regulated article in the Dry Kiln Operator's Manual, Agriculture Handbook 188, which is... the United States Environmental Protection Agency. (Approved by the Office of Management and Budget...

Modification of physical properties of freeze-dried rice

NASA Technical Reports Server (NTRS)

Huber, C. S.

1971-01-01

Freeze cycling process consists of alternately freezing and thawing precooked rice for two cycles, rice is then frozen and freeze-dehydrated in vacuum sufficient to remove water from rice by sublimitation. Process modifies rice grain structure and porosity, enabling complete rehydration in one minute in hot water.

Physicochemical and in vitro antioxidant properties of pectin extracted from hot pepper (Capsicum annuum L. var. acuminatum (Fingerh.)) residues with hydrochloric and sulfuric acids.

PubMed

Xu, Honggao; Tai, Kedong; Wei, Tong; Yuan, Fang; Gao, Yanxiang

2017-11-01

Transformation of hot pepper residues to value-added products with concomitant benefits on environmental pollution would be of great value to capsicum oleoresin manufacturers. Pectin, a soluble dietary fiber with multiple functions, from hot pepper residues was investigated in this study. The extraction of hot pepper pectin using hydrochloric acid was first optimized using response surface methodology (RSM). The most efficient parameters for maximum hot pepper pectin yield (14.63%, dry basis) were a pH of 1.0, a temperature of 90 °C, an extraction time of 2 h and a liquid-to-solid ratio of 20 L g -1 . The pectin was mainly composed of uronic acids, and the major neutral sugars were galactose and glucose. The structure of hot pepper pectin was characterized by homogalacturonan and rhamnogalacturonan I elements. The physicochemical properties of hot pepper pectin extracted by sulfuric acid and hydrochloric acid were further investigated. The content of protein and degree of esterification in hot pepper pectin extracted with sulfuric acid solution (SP) were higher (P < 0.05) than those in that extracted with hydrochloric acid solution (HP), while the mean molecular weight of SP was lower than that of HP. Compared with HP, SP exhibited higher viscosity and better emulsifying property. Based on the yield and physicochemical properties of hot pepper pectin, hot pepper residues would be a new source to obtain pectin, and SP would be more preferred than HP. © 2017 Society of Chemical Industry. © 2017 Society of Chemical Industry.

Existence domains of slow and fast ion-acoustic solitons in two-ion space plasmas

DOE Office of Scientific and Technical Information (OSTI.GOV)

Maharaj, S. K., E-mail: smaharaj@sansa.org.za; Bharuthram, R., E-mail: rbharuthram@uwc.ac.za; Singh, S. V., E-mail: satyavir@iigs.iigm.res.in

2015-03-15

A study of large amplitude ion-acoustic solitons is conducted for a model composed of cool and hot ions and cool and hot electrons. Using the Sagdeev pseudo-potential formalism, the scope of earlier studies is extended to consider why upper Mach number limitations arise for slow and fast ion-acoustic solitons. Treating all plasma constituents as adiabatic fluids, slow ion-acoustic solitons are limited in the order of increasing cool ion concentrations by the number densities of the cool, and then the hot ions becoming complex valued, followed by positive and then negative potential double layer regions. Only positive potentials are found formore » fast ion-acoustic solitons which are limited only by the hot ion number density having to remain real valued. The effect of neglecting as opposed to including inertial effects of the hot electrons is found to induce only minor quantitative changes in the existence regions of slow and fast ion-acoustic solitons.« less

Electrolyte changes in the blood plasma of broilers as influenced by cooling during summer

NASA Astrophysics Data System (ADS)

Sharma, M. L.; Gangwar, P. C.

1987-09-01

High temperature significantly (P < 0.01) decreased the Na+ and K+ concentrations in the blood plasma of both the sexes of broilers during 4 to 8 weeks of age. Relatively constant levels of these electrolytes were observed during this phase of growth and the sex of the bird had no significant effect on their levels. Greater broiler weights and higher levels of plasma electrolyte were achieved by the use of cooling systems (which were more effective in the hot dry part of the summer than in the hot humid part).

Mulga, a major tropical dry open forest of Australia: recent insights to carbon and water fluxes

NASA Astrophysics Data System (ADS)

Eamus, Derek; Huete, Alfredo; Cleverly, James; Nolan, Rachael H.; Ma, Xuanlong; Tarin, Tonantzin; Santini, Nadia S.

2016-12-01

Mulga, comprised of a complex of closely related Acacia spp., grades from a low open forest to tall shrublands in tropical and sub-tropical arid and semi-arid regions of Australia and experiences warm-to-hot annual temperatures and a pronounced dry season. This short synthesis of current knowledge briefly outlines the causes of the extreme variability in rainfall characteristic of much of central Australia, and then discusses the patterns and drivers of variability in carbon and water fluxes of a central Australian low open Mulga forest. Variation in phenology and the impact of differences in the amount and timing of precipitation on vegetation function are then discussed. We use field observations, with particular emphasis on eddy covariance data, coupled with modelling and remote sensing products to interpret inter-seasonal and inter-annual patterns in the behaviour of this ecosystem. We show that Mulga can vary between periods of near carbon neutrality to periods of being a significant sink or source for carbon, depending on both the amount and timing of rainfall. Further, we demonstrate that Mulga contributed significantly to the 2011 global land sink anomaly, a result ascribed to the exceptional rainfall of 2010/2011. Finally, we compare and contrast the hydraulic traits of three tree species growing close to the Mulga and show how each species uses different combinations of trait strategies (for example, sapwood density, xylem vessel implosion resistance, phenological guild, access to groundwater and Huber value) to co-exist in this semi-arid environment. Understanding the inter-annual variability in functional behaviour of this important arid-zone biome and mechanisms underlying species co-existence will increase our ability to predict trajectories of carbon and water balances for future changing climates.

Existence domains of arbitrary amplitude nonlinear structures in two-electron temperature space plasmas. II. High-frequency electron-acoustic solitons

DOE Office of Scientific and Technical Information (OSTI.GOV)

Maharaj, S. K.; Bharuthram, R.; Singh, S. V.

2012-12-15

A three-component plasma model composed of ions, cool electrons, and hot electrons is adopted to investigate the existence of large amplitude electron-acoustic solitons not only for the model for which inertia and pressure are retained for all plasma species which are assumed to be adiabatic but also neglecting inertial effects of the hot electrons. Using the Sagdeev potential formalism, the Mach number ranges supporting the existence of large amplitude electron-acoustic solitons are presented. The limitations on the attainable amplitudes of electron-acoustic solitons having negative potentials are attributed to a number of different physical reasons, such as the number density ofmore » either the cool electrons or hot electrons ceases to be real valued beyond the upper Mach number limit, or, alternatively, a negative potential double layer occurs. Electron-acoustic solitons having positive potentials are found to be supported only if inertial effects of the hot electrons are retained and these are found to be limited only by positive potential double layers.« less

The Hot Hand Belief and Framing Effects

ERIC Educational Resources Information Center

MacMahon, Clare; Köppen, Jörn; Raab, Markus

2014-01-01

Purpose: Recent evidence of the hot hand in sport--where success breeds success in a positive recency of successful shots, for instance--indicates that this pattern does not actually exist. Yet the belief persists. We used 2 studies to explore the effects of framing on the hot hand belief in sport. We looked at the effect of sport experience and…

Soil-atmospheric exchange of CO2, CH4, and N2O in three subtropical forest ecosystems in southern China

USGS Publications Warehouse

Tang, X.; Liu, S.; Zhou, G.; Zhang, Dongxiao; Zhou, C.

2006-01-01

The magnitude, temporal, and spatial patterns of soil-atmospheric greenhouse gas (hereafter referred to as GHG) exchanges in forests near the Tropic of Cancer are still highly uncertain. To contribute towards an improvement of actual estimates, soil-atmospheric CO2, CH4, and N2O fluxes were measured in three successional subtropical forests at the Dinghushan Nature Reserve (hereafter referred to as DNR) in southern China. Soils in DNR forests behaved as N2O sources and CH4 sinks. Annual mean CO2, N2O, and CH4 fluxes (mean ?? SD) were 7.7 ?? 4.6MgCO2-Cha-1 yr-1, 3.2 ?? 1.2 kg N2ONha-1 yr-1, and 3.4 ?? 0.9 kgCH4-Cha-1 yr-1, respectively. The climate was warm and wet from April through September 2003 (the hot-humid season) and became cool and dry from October 2003 through March 2004 (the cool-dry season). The seasonality of soil CO2 emission coincided with the seasonal climate pattern, with high CO2 emission rates in the hot-humid season and low rates in the cool-dry season. In contrast, seasonal patterns of CH4 and N2O fluxes were not clear, although higher CH4 uptake rates were often observed in the cool-dry season and higher N2O emission rates were often observed in the hot-humid season. GHG fluxes measured at these three sites showed a clear increasing trend with the progressive succession. If this trend is representative at the regional scale, CO2 and N2O emissions and CH4 uptake in southern China may increase in the future in light of the projected change in forest age structure. Removal of surface litter reduced soil CO2 effluxes by 17-44% in the three forests but had no significant effect on CH4 absorption and N2O emission rates. This suggests that microbial CH4 uptake and N2O production was mainly related to the mineral soil rather than in the surface litter layer. ?? 2006 Blackwell Publishing Ltd.

Summer syncope syndrome redux.

PubMed

Huang, Jennifer Juxiang; Desai, Chirag; Singh, Nirmal; Sharda, Natasha; Fernandes, Aaron; Riaz, Irbaz Bin; Alpert, Joseph S

2015-10-01

While antihypertensive therapy is known to reduce the risk for heart failure, myocardial infarction, and stroke, it can often cause orthostatic hypotension and syncope, especially in the setting of polypharmacy and possibly, a hot and dry climate. The objective of the present study was to investigate whether the results of our prior study involving continued use of antihypertensive drugs at the same dosage in the summer as in the winter months for patients living in the Sonoran desert resulted in an increase in syncopal episodes during the hot summer months. All hypertensive patients who were treated with medications and admitted with International Classification of Diseases, 9th Revision code diagnosis of syncope were included. This is a 3-year retrospective chart review study. They were defined as "cases" if they presented during the summer months (May to September) and "controls" if they presented during the winter months (November to March). The primary outcome measure was the presence of clinical dehydration. The statistical significance was determined using the 2-sided Fisher's exact test. A total of 834 patients with an International Classification of Diseases, 9th Revision code diagnosis of syncope were screened: 477 in the summer months and 357 in the winter months. In patients taking antihypertensive medications, there was a significantly higher number of cases of syncope secondary to dehydration during the summer months (40.5%) compared with the winter months (29%) (P = .04). No difference was observed in the type of antihypertensive medication used and syncope rate. The number of antihypertensives used did not increase the cases of syncope in either summer or winter. An increased number of syncope events was observed in the summer months among people who reside in a dry desert climate and who are taking antihypertensive medications. The data confirm our earlier observations that demonstrated a greater number of cases of syncope among people who reside in a dry desert climate who were taking antihypertensive medications during summer months. We recommend judicious reduction of antihypertensive therapy in patients residing in a hot and dry climate, particularly during the summer months. Copyright © 2015 Elsevier Inc. All rights reserved.

Radiocarbon Ages and Environments of Deposition of the Wono and Trego Hot Springs Tephra Layers in the Pyramid Lake Subbasin, Nevada

USGS Publications Warehouse

Benson, L.V.; Smoot, J.P.; Kashgarian, Michaele; Sarna-Wojcicki, A.; Burdett, J.W.

1997-01-01

Uncalibrated radiocarbon data from core PLC92B taken from Wizards Cove in the Pyramid Lake subbasin indicate that the Trego Hot Springs and Wono tephra layers were deposited 23,200 ?? 300 and 27,300 ??300 14C yr B.P. (uncorrected for reservoir effect). Sedimentological data from sites in the Pyramid Lake and Smoke Creek-Black Rock Desert subbasins indicate that the Trego Hot Springs tephra layer was deposited during a relatively dry period when Pyramid Lake was at or below its spill point (1177 m) to the Winnemucca Lake subbasin. The Wono tephra layer was deposited when lake depth was controlled by spill across Emerson Pass sill (1207 m) to the Smoke Creek-Black Rock Desert subbasin. 18O data from core PLC92B also support the concept that the Trego Hot Springs tephra fell into a relatively shallow Pyramid Lake and that the Wono tephra fell into a deeper spilling lake. ?? 1997 University of Washington.

Non-enzymatic browning and flavour kinetics of vacuum dried onion slices

NASA Astrophysics Data System (ADS)

Mitra, Jayeeta; Shrivastava, Shanker L.; Rao, Pavuluri S.

2015-01-01

Onion slices were dehydrated under vacuum to produce good quality dried ready-to-use onion slices. Colour development due to non-enzymatic browning and flavour loss in terms of thiosulphinate concentration was determined, along with moisture content and rehydration ratio. Kinetics of non-enzymatic browning and thiosulphinate loss during drying was analysed. Colour change due to non-enzymatic browning was found to be much lower in the case of vacuum dried onion, and improved flavour retention was observed as compared to hot air dried onion slices. The optical index values for non-enzymatic browning varied from 18.41 to 38.68 for untreated onion slices and from 16.73 to 36.51 for treated slices, whereas thiosulphinate concentration in the case of untreated onion slices was within the range of 2.96-3.92 μmol g-1 for dried sample and 3.71-4.43 μmol g-1 for the treated onion slices. Rehydration ratio was also increased, which may be attributed to a better porous structure attained due to vacuum drying. The treatment applied was found very suitable in controlling non-enzymatic browning and flavour loss during drying, besides increasing rehydration ratio. Hence, high quality dried ready- to-use onion slices were prepared.

Extraction condition optimization and effects of drying methods on physicochemical properties and antioxidant activities of polysaccharides from comfrey (Symphytum officinale L.) root.

PubMed

Shang, Hongmei; Zhou, Haizhu; Duan, Mengying; Li, Ran; Wu, Hongxin; Lou, Yujie

2018-06-01

This study was designed to investigate the extraction conditions of polysaccharides from comfrey (Symphytum officinale L.) root (CRPs) using response surface methodology (RSM). The effects of three variables including liquid-solid ratio, extraction time and extraction temperature on the extraction yield of CRPs were taken into consideration. Moreover, the effects of drying methods including hot air drying (HD), vacuum drying (VD) and freeze drying (FD) on the physicochemical properties and antioxidant activities of CRPs were evaluated. The optimal conditions to extract the polysaccharides were as follows: liquid-solid ratio (15mL/g), extraction time (74min), and extraction temperature (95°C), allowed a maximum polysaccharides yield of 22.87%. Different drying methods had significant effects on the physicochemical properties of CRPs such as the chemical composition (contents of total polysaccharides and uronic acid), relative viscosity, solubility and molecular weight. CRPs drying with FD method showed stronger reducing power and radical scavenging capacities against DPPH and ABTS radicals compared with CRPs drying with HD and VD methods. Therefore, freeze drying served as a good method for keeping the antioxidant activities of polysaccharides from comfrey root. Copyright © 2018 Elsevier B.V. All rights reserved.

Evaluation of common bean (Phaseolus vulgaris) response to charcoal rot

USDA-ARS?s Scientific Manuscript database

Charcoal rot in common beans (Phaseolus vulgaris L.), caused by Macrophomina phaseolina (Tassi) Gold. (Mph), is an endemic disease in the prevailing hot and dry conditions in southern Puerto Rico. This study evaluated the 120 bean genotypes that compose the BASE 120 panel under screenhouse conditio...

Comprehensive evaluation of the long-term performance of rubberized pavement, phase II : the influence of rubber and asphalt interaction on mixture durability.

DOT National Transportation Integrated Search

2014-12-01

This project investigated the long-term performance of hot asphalt mixes containing crumb rubber : modifiers (CRM) added in dry or wet processes. A total of eight asphalt mixturesfour Porous : European Mixtures (PEMs) and four Stone Matrix Asphalt...

PARTITIONING OF WATER FLUX IN A SIERRA NEVADA PONDEROSA PINE PLANTATION. (R826601)

EPA Science Inventory

The weather patterns of the west side of the Sierra Nevada Mountains (cold, wet winters and hot, dry summers) strongly influence how water is partitioned between transpiration and evaporation and result in a specific strategy of water use by ponderosa pine trees (Pinus pond...