The economic value of innovative treatments over the product life cycle: the case of targeted trastuzumab therapy for breast cancer.

PubMed

Garrison, Louis P; Veenstra, David L

2009-01-01

Pharmacoeconomic analyses typically project the expected cost-effectiveness of a new product for a specific indication. This analysis develops a dynamic life-cycle model to conduct a multi-indication evaluation using the case of trastuzumab licensed in the United States for both early-stage and metastatic (or late-stage) human epidermal growth factor receptor 2 (HER2)-positive breast cancer therapy (early breast cancer [EBC]; metastatic breast cancer [MBC]), approved in 2006 and 1998, respectively. This dynamic model combined information on expected incremental cost-utility ratios for specific indications with an epidemiologically based projection of utilization by indication over the product life cycle-from 1998 to 2016. Net economic value was estimated as the cumulative quality-adjusted life years (QALYs) gained over the life cycle multiplied by a societal valuation of health gains ($/QALY) minus cumulative net direct treatment costs. Sensitivity analyses were performed under a range of assumptions. We projected that the annual number of EBC patients receiving trastuzumab will be more than three times that of MBC by 2016, in part because adjuvant treatment reduces the future incidence of MBC. Over this life cycle, the estimated overall incremental cost-effectiveness ratio (ICER) was $35,590/QALY with a total of 432,547 discounted QALYs gained. Under sensitivity analyses, the overall ICER varied from $21,000 to $53,000/QALY, and the projected net economic value resulting from trastuzumab treatment ranged from $6.2 billion to $49.5 billion. Average ICERs for multi-indication compounds can increase or decrease over the product life cycle. In this example, the projected overall life-cycle ICER for trastuzumab was less than one half of that in the initial indication. This dynamic perspective-versus the usual static one-highlights the interdependence of drug development decisions and investment incentives, raising important reimbursement policy issues.

Calibration of material models for estimating impact of construction quality on life cycle performance of pavements.

DOT National Transportation Integrated Search

2006-02-01

Constructing a pavement that will perform well throughout its expected design life is the main goal of any highway agency. The relationship between construction parameters and pavement life, defined by structural models, can be described using materi...

Applications of a Wage-Turnover Model to the Shipbuilding Industry.

DTIC Science & Technology

1980-02-08

wage differential leaving a firm indifferent between the two groups is 1 3 J2 Because older workers have a shorter work- life expectancy, their rate...discussion of the relationship between current and future wage rates over a worker’s life cycle, see Joanne Salop and Steven Salop, "Self Selection...existing wage scales. 24- F4or an optimal solution to the problem of life -cycle wage Fates from the perspective of the firm, Information is needed on

A new concept for high-cycle-life LEO: Rechargeable MnO2-hydrogen

NASA Technical Reports Server (NTRS)

Appleby, A. J.; Dhar, H. P.; Kim, Y. J.; Murphy, O. J.

1989-01-01

The nickel-hydrogen secondary battery system, developed in the early 1970s, has become the system of choice for geostationary earth orbit (GEO) applications. However, for low earth orbit (LEO) satellites with long expected lifetimes the nickel positive limits performance. This requires derating of the cell to achieve very long cycle life. A new system, rechargeable MnO2-Hydrogen, which does not require derating, is described here. For LEO applications, it promises to have longer cycle life, high rate capability, a higher effective energy density, and much lower self-discharge behavior than those of the nickel-hydrogen system.

Gimme shelter--the relative sensitivity of parasitic nematodes with direct and indirect life cycles to climate change.

PubMed

Molnár, Péter K; Dobson, Andrew P; Kutz, Susan J

2013-11-01

Climate change is expected to alter the dynamics of host-parasite systems globally. One key element in developing predictive models for these impacts is the life cycle of the parasite. It is, for example, commonly assumed that parasites with an indirect life cycle would be more sensitive to changing environmental conditions than parasites with a direct life cycle due to the greater chance that at least one of their obligate host species will go extinct. Here, we challenge this notion by contrasting parasitic nematodes with a direct life cycle against those with an indirect life cycle. Specifically, we suggest that behavioral thermoregulation by the intermediate host may buffer the larvae of indirectly transmitted parasites against temperature extremes, and hence climate warming. We term this the 'shelter effect'. Formalizing each life cycle in a comprehensive model reveals a fitness advantage for the direct life cycle over the indirect life cycle at low temperatures, but the shelter effect reverses this advantage at high temperatures. When examined for seasonal environments, the models suggest that climate warming may in some regions create a temporal niche in mid-summer that excludes parasites with a direct life cycle, but allows parasites with an indirect life cycle to persist. These patterns are amplified if parasite larvae are able to manipulate their intermediate host to increase ingestion probability by definite hosts. Furthermore, our results suggest that exploiting the benefits of host sheltering may have aided the evolution of indirect life cycles. Our modeling framework utilizes the Metabolic Theory of Ecology to synthesize the complexities of host behavioral thermoregulation and its impacts on various temperature-dependent parasite life history components in a single measure of fitness, R0 . It allows quantitative predictions of climate change impacts, and is easily generalized to many host-parasite systems. © 2013 John Wiley & Sons Ltd.

Sign Life-Cycle Policies and Practices : Transportation Research Synthesis

DOT National Transportation Integrated Search

2017-10-01

MnDOT Metro District Traffic Engineering is interested in the practices that other state departments of transportation (DOTs) use to determine traffic sign life expectancy and replacement. Of particular interest is the state of the practice regarding...

What do stakeholders expect from patient engagement: Are these expectations being met?

PubMed

Boudes, Mathieu; Robinson, Paul; Bertelsen, Neil; Brooke, Nicholas; Hoos, Anton; Boutin, Marc; Geissler, Jan; Sargeant, Ify

2018-06-01

Meaningful patient engagement (PE) in medicines development and during the life cycle of a product requires all stakeholders have a clear understanding of respective expectations. A qualitative survey was undertaken to understand stakeholder expectations. The survey explored 4 themes from the perspective of each stakeholder group: meaning, views, expectations and priorities for PE. Participants were grouped into 7 categories: policymakers/regulators; health-care professionals (HCPs); research funders; payers/purchasers/HTA; patients/patient representatives; pharmaceutical/life sciences industry; and academic researchers. Fifty-nine interviews were conducted across a range of geographies, PE experience and job seniority/role. There was consensus across stakeholders on meaning of PE; importance of promoting PE to a higher level than currently; need for a more structured process and guidance. There was little consensus on stakeholder expectations and roles. Policymakers/regulators were expected by others to drive PE, create a framework and facilitate PE, provide guidelines of good practice and connect stakeholders, but this expectation was not shared by the policymakers/regulators group. HCPs were seen as the link between patients and other stakeholders, but HCPs did not necessarily share this view. Despite broad stakeholder categories, clear themes emerged: there is no "leader"; no stakeholder has a clear view on how to meaningfully engage with patients; there are educational gaps; and a structure and guidance for PE is urgently required. Given the diversity of stakeholders, there needs to be multistakeholder collaborative leadership. Effective collaboration requires consensus on roles, responsibilities and expectations to synergize efforts to deliver meaningful PE in medicines life cycle. © 2018 The Authors. Health Expectations published by John Wiley & Sons Ltd.

Life-Cycle-Cost Analysis of the Microwave Landing System Ground and Airborne Systems

DTIC Science & Technology

1981-10-01

constant 1980 dollars, with a production rate variability. Table S-3 presents the life-cycle costs by MLS configuration and total system implementation... PRODUCTION RATE VARIABILITY OVER A THREE-YEAR PFODUCTXION RUN (MILLIONS OF CONSTANT 1980 DOLLARS) Pruduction (Juantitl•e and Costs system Typ 75...Implementation strategies * Production schedules for MLS equipment The LCC was determined to be relatively insensitive to changes in MTBF. This was expected

FY 1996 solid waste integrated life-cycle forecast characteristics summary. Volumes 1 and 2

DOE Office of Scientific and Technical Information (OSTI.GOV)

Templeton, K.J.

1996-05-23

For the past six years, a waste volume forecast has been collected annually from onsite and offsite generators that currently ship or are planning to ship solid waste to the Westinghouse Hanford Company`s Central Waste Complex (CWC). This document provides a description of the physical waste forms, hazardous waste constituents, and radionuclides of the waste expected to be shipped to the CWC from 1996 through the remaining life cycle of the Hanford Site (assumed to extend to 2070). In previous years, forecast data has been reported for a 30-year time period; however, the life-cycle approach was adopted this year tomore » maintain consistency with FY 1996 Multi-Year Program Plans. This document is a companion report to two previous reports: the more detailed report on waste volumes, WHC-EP-0900, FY1996 Solid Waste Integrated Life-Cycle Forecast Volume Summary and the report on expected containers, WHC-EP-0903, FY1996 Solid Waste Integrated Life-Cycle Forecast Container Summary. All three documents are based on data gathered during the FY 1995 data call and verified as of January, 1996. These documents are intended to be used in conjunction with other solid waste planning documents as references for short and long-term planning of the WHC Solid Waste Disposal Division`s treatment, storage, and disposal activities over the next several decades. This document focuses on two main characteristics: the physical waste forms and hazardous waste constituents of low-level mixed waste (LLMW) and transuranic waste (both non-mixed and mixed) (TRU(M)). The major generators for each waste category and waste characteristic are also discussed. The characteristics of low-level waste (LLW) are described in Appendix A. In addition, information on radionuclides present in the waste is provided in Appendix B. The FY 1996 forecast data indicate that about 100,900 cubic meters of LLMW and TRU(M) waste is expected to be received at the CWC over the remaining life cycle of the site. Based on ranges provided by the waste generators, this baseline volume could fluctuate between a minimum of about 59,720 cubic meters and a maximum of about 152,170 cubic meters. The range is primarily due to uncertainties associated with the Tank Waste Remediation System (TWRS) program, including uncertainties regarding retrieval of long-length equipment, scheduling, and tank retrieval technologies.« less

Environmental Impact Assessment and End-of-Life Treatment Policy Analysis for Li-Ion Batteries and Ni-MH Batteries

PubMed Central

Yu, Yajuan; Chen, Bo; Huang, Kai; Wang, Xiang; Wang, Dong

2014-01-01

Based on Life Cycle Assessment (LCA) and Eco-indicator 99 method, a LCA model was applied to conduct environmental impact and end-of-life treatment policy analysis for secondary batteries. This model evaluated the cycle, recycle and waste treatment stages of secondary batteries. Nickel-Metal Hydride (Ni-MH) batteries and Lithium ion (Li-ion) batteries were chosen as the typical secondary batteries in this study. Through this research, the following results were found: (1) A basic number of cycles should be defined. A minimum cycle number of 200 would result in an obvious decline of environmental loads for both battery types. Batteries with high energy density and long life expectancy have small environmental loads. Products and technology that help increase energy density and life expectancy should be encouraged. (2) Secondary batteries should be sorted out from municipal garbage. Meanwhile, different types of discarded batteries should be treated separately under policies and regulations. (3) The incineration rate has obvious impact on the Eco-indicator points of Nickel-Metal Hydride (Ni-MH) batteries. The influence of recycle rate on Lithium ion (Li-ion) batteries is more obvious. These findings indicate that recycling is the most promising direction for reducing secondary batteries’ environmental loads. The model proposed here can be used to evaluate environmental loads of other secondary batteries and it can be useful for proposing policies and countermeasures to reduce the environmental impact of secondary batteries. PMID:24646862

Environmental impact assessment and end-of-life treatment policy analysis for Li-ion batteries and Ni-MH batteries.

PubMed

Yu, Yajuan; Chen, Bo; Huang, Kai; Wang, Xiang; Wang, Dong

2014-03-18

Based on Life Cycle Assessment (LCA) and Eco-indicator 99 method, a LCA model was applied to conduct environmental impact and end-of-life treatment policy analysis for secondary batteries. This model evaluated the cycle, recycle and waste treatment stages of secondary batteries. Nickel-Metal Hydride (Ni-MH) batteries and Lithium ion (Li-ion) batteries were chosen as the typical secondary batteries in this study. Through this research, the following results were found: (1) A basic number of cycles should be defined. A minimum cycle number of 200 would result in an obvious decline of environmental loads for both battery types. Batteries with high energy density and long life expectancy have small environmental loads. Products and technology that help increase energy density and life expectancy should be encouraged. (2) Secondary batteries should be sorted out from municipal garbage. Meanwhile, different types of discarded batteries should be treated separately under policies and regulations. (3) The incineration rate has obvious impact on the Eco-indicator points of Nickel-Metal Hydride (Ni-MH) batteries. The influence of recycle rate on Lithium ion (Li-ion) batteries is more obvious. These findings indicate that recycling is the most promising direction for reducing secondary batteries' environmental loads. The model proposed here can be used to evaluate environmental loads of other secondary batteries and it can be useful for proposing policies and countermeasures to reduce the environmental impact of secondary batteries.

Social and Affective Factors Associated with Adolescent Pregnancy.

ERIC Educational Resources Information Center

Smith, Peggy B.; And Others

1982-01-01

Study examined perceptions of pregnancy, including life-expectations, desire for pregnancy, and knowledge of menstrual cycle in a sample of pregnant urban adolescents. Results indicate that, although teens were aware of birth control methods, they had little understanding of menstrual cycle and its relationship to intercourse. And while few…

Service life assessment of timber highway bridges in USA climate zones

Treesearch

James P. Wacker; Brian K. Brashaw; Thomas G. Williamson; P. David Jones; Matthew S. Smith; Travis K. Hosteng; David L. Strahl; Lola E. Coombe; V.J. Gopu

2014-01-01

As engineers begin to estimate life-cycle costs and sustainable design approaches for timber bridges, there is a need for more reliable data about their durability and expected service life. This paper summarizes a comprehensive effort to assess the current condition of more than one hundred timber highway bridge superstructures throughout the United States. This...

Extending Depot Length and Intervals for DDG 51 Class Ships: Examining the 72 Month Operational Cycle

DTIC Science & Technology

2016-01-01

tenance period to achieve planned expected service life ( ESL ), as well as the length, workload, and periodicity of a continuous maintenance...a ship’s service life but extends the length of each deployment. Figure 2.1 compares the number of deployments that can be made over the ESL of...ships in different cycle lengths. The ESL of DDG-51 Arleigh Burke–class destroyers Flight I and II is 35 years, and Flight IIA has an ESL of 40 years

Demographic Change, Social Security Systems, and Savings1

PubMed Central

Bloom, David E.; Canning, David; Mansfield, Richard K.; Moore, Michael

2009-01-01

In theory, improvements in healthy life expectancy should generate increases in the average age of retirement, with little effect on savings rates. In many countries, however, retirement incentives in social security programs prevent retirement ages from keeping pace with changes in life expectancy, leading to an increased need for life-cycle savings. Analyzing a cross-country panel of macroeconomic data, we find that increased longevity raises aggregate savings rates in countries with universal pension coverage and retirement incentives, though the effect disappears in countries with pay-as-you-go systems and high replacement rates. PMID:19865594

Improving cycle life of layered lithium transition metal oxide (LiMO2) based positive electrodes for Li ion batteries by smart selection of the electrochemical charge conditions

NASA Astrophysics Data System (ADS)

Kasnatscheew, Johannes; Evertz, Marco; Streipert, Benjamin; Wagner, Ralf; Nowak, Sascha; Cekic Laskovic, Isidora; Winter, Martin

2017-08-01

Increasing the specific energy of a lithium ion battery and maintaining its cycle life is a predominant goal and major challenge for electrochemical energy storage applications. Focusing on the positive electrode as the specific energy bottleneck, cycle life characteristics of promising layered oxide type active materials (LiMO2) has been thoroughly investigated. Comparing the variety of LiMO2 compositions, it could be shown that the "Ni-rich" (Ni ≥ 60% for M in LiMO2) electrodes expectably revealed best performance compromises between specific energy and cycle life at 20 °C, but only LiNi0.6Mn0.2Co0.2O2 (NMC622) could also maintain sufficient cycle performance at elevated temperatures. Focusing on NMC622, it could be demonstrated that the applied electrochemical conditions (charge capacity, delithiation amount) in the formation cycles significantly influence the subsequent cycling performance. Moreover, the insignificant transition metal dissolution, demonstrated by means of total X-ray fluorescence (TXRF) technique, and unchanged lithiation degree in the discharged state, determined by the measurement of the Li+ content by means of the inductively coupled plasma optical emission spectroscopy (ICP-OES) technique, pointed to a delithiation (charge) hindrance capacity fade mechanism. Considering these insights, thoughtful modifications of the electrochemical charge conditions could significantly prolong the cycle life.

41 CFR 102-35.20 - What definitions apply to GSA's personal property regulations?

Code of Federal Regulations, 2014 CFR

2014-01-01

... surveillance of personal property throughout its complete life cycle using various property management tools... includes nonexpendable personal property whose expected useful life is two years or longer and whose...) Statement of Federal Financial Accounting Standards No. 6 Accounting for Property, Plant and Equipment...

41 CFR 102-35.20 - What definitions apply to GSA's personal property regulations?

Code of Federal Regulations, 2012 CFR

2012-01-01

... surveillance of personal property throughout its complete life cycle using various property management tools... includes nonexpendable personal property whose expected useful life is two years or longer and whose...) Statement of Federal Financial Accounting Standards No. 6 Accounting for Property, Plant and Equipment...

41 CFR 102-35.20 - What definitions apply to GSA's personal property regulations?

Code of Federal Regulations, 2013 CFR

2013-07-01

... surveillance of personal property throughout its complete life cycle using various property management tools... includes nonexpendable personal property whose expected useful life is two years or longer and whose...) Statement of Federal Financial Accounting Standards No. 6 Accounting for Property, Plant and Equipment...

44 CFR 206.117 - Housing assistance.

Code of Federal Regulations, 2014 CFR

2014-10-01

... United States or in another location where alternative housing resources are not available and the types... an insular area outside the continental United States, or in a location where alternative housing... efficiency, maintenance, and life cycle cost, and with a life expectancy of more than 5 years but less than...

Physical activity types and life expectancy with and without cardiovascular disease: the Rotterdam Study.

PubMed

Dhana, Klodian; Koolhaas, Chantal M; Berghout, Mathilde A; Peeters, Anna; Ikram, M Arfan; Tiemeier, Henning; Hofman, Albert; Nusselder, Wilma; Franco, Oscar H

2017-12-01

We aimed to determine the contribution of specific physical activity (PA) types (i.e. walking, cycling, domestic work, sports and gardening) on total life expectancy (LE) and LE with and without cardiovascular disease (CVD). We constructed multistate life tables to calculate the effects of total PA and PA types on LE, among individuals older than 55 years from the Rotterdam Study. For the life table calculations, we used sex-specific prevalences, incident rates and hazard ratios for three transitions (healthy-to-CVD, healthy-to-death and CVD-to-death) by levels of PA and adjusted for confounders. High total PA was associated with gains in total and CVD-free LE. High cycling contributed to higher total LE in men (3.7 years) and women (2.1 years) and higher LE without CVD in men (3.1 years) and women (2.4 years). Total and CVD-free LE were increased by high domestic work in women (2.6 and 2.4 years, respectively) and high gardening in men (2.7 and 2.0 years, respectively). Higher PA levels are associated with increased LE and more years lived without CVD. Of the different PA types, cycling provided high effects in both men and women. Cycling could be more strongly encouraged in activity guidelines to maximize the population benefits of PA. © The Author 2016. Published by Oxford University Press on behalf of Faculty of Public Health. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com

Life cycle and fecundity analysis of Lutzomyia shannoni (Dyar) (Diptera: Psychodidae).

PubMed

Ferro, C; Cárdenas, E; Corredor, D; Morales, A; Munstermann, L E

1998-01-01

The life cycle of Lutzomyia shannoni (Dyar), was described for laboratory conditions with maximum daily temperature of 27-30 degree C, minimum daily temperatures of 22-27 degree C and relative humidity between 87-99%. Life cycle in each stage was as follows: egg 6-12 days (ave, 8.5 days); first stage larva 5-13 days (ave. 9.6 days); second stage larva 4-13 days (ave. 9.2 days); third stage larva 5-19 days (ave. 11.8 days); fourth stage larva 7-37 days (ave. 19.9 days); pupa 7-32 days (ave. 15.2 days). The life expectancy of adults ranged from 4 to 15 days (ave. 8.6 days). The entire egg to adult period ranged from 36 to 74 days (ave. 54.6 days). On average, each female oviposited 22.7 eggs; the average egg retention per female was 24.3 eggs.

The evaluation life cycle: a retrospective assessment of stages and phases of the circles of care initiative.

PubMed

Bess, Gary; Allen, James; Deters, Pamela B

2004-08-12

A life cycle metaphor characterizes the evolving relationship between the evaluator and program staff. This framework suggests that common developmental dynamics occur in roughly the same order across groups and settings. There are stage-specific dynamics that begin with Pre-History, which characterize the relationship between the grantees and evaluator. The stages are: (a) Pre-History, (b) Process, (c) Development, (d) Action, (e) Findings-Compilation, and (f) Transition. The common dynamics, expectations, and activities for each stage are discussed.

[The construction of life profiles by social class in Chile].

PubMed

Torres, C

1989-11-01

The author develops a series of life profiles for men and women living in the Greater Santiago area of Chile over the past 25 years. These profiles, which are based on the concept of life expectancy at birth, illustrate the length of time individuals take to go through such life cycle stages as education, employment, unemployment, and retirement. The concept is used to analyze changes in the life profile over time and how these differ by class. (SUMMARY IN ENG)

Insulation Cork Boards-Environmental Life Cycle Assessment of an Organic Construction Material.

PubMed

Silvestre, José D; Pargana, Nuno; de Brito, Jorge; Pinheiro, Manuel D; Durão, Vera

2016-05-20

Envelope insulation is a relevant technical solution to cut energy consumption and reduce environmental impacts in buildings. Insulation Cork Boards (ICB) are a natural thermal insulation material whose production promotes the recycling of agricultural waste. The aim of this paper is to determine and evaluate the environmental impacts of the production, use, and end-of-life processing of ICB. A "cradle-to-cradle" environmental Life Cycle Assessment (LCA) was performed according to International LCA standards and the European standards on the environmental evaluation of buildings. These results were based on site-specific data and resulted from a consistent methodology, fully described in the paper for each life cycle stage: Cork oak tree growth, ICB production, and end-of-life processing-modeling of the carbon flows ( i.e. , uptakes and emissions), including sensitivity analysis of this procedure; at the production stage-the modeling of energy processes and a sensitivity analysis of the allocation procedures; during building operation-the expected service life of ICB; an analysis concerning the need to consider the thermal diffusivity of ICB in the comparison of the performance of insulation materials. This paper presents the up-to-date "cradle-to-cradle" environmental performance of ICB for the environmental categories and life-cycle stages defined in European standards.

Insulation Cork Boards—Environmental Life Cycle Assessment of an Organic Construction Material

PubMed Central

Silvestre, José D.; Pargana, Nuno; de Brito, Jorge; Pinheiro, Manuel D.; Durão, Vera

2016-01-01

Envelope insulation is a relevant technical solution to cut energy consumption and reduce environmental impacts in buildings. Insulation Cork Boards (ICB) are a natural thermal insulation material whose production promotes the recycling of agricultural waste. The aim of this paper is to determine and evaluate the environmental impacts of the production, use, and end-of-life processing of ICB. A “cradle-to-cradle” environmental Life Cycle Assessment (LCA) was performed according to International LCA standards and the European standards on the environmental evaluation of buildings. These results were based on site-specific data and resulted from a consistent methodology, fully described in the paper for each life cycle stage: Cork oak tree growth, ICB production, and end-of-life processing-modeling of the carbon flows (i.e., uptakes and emissions), including sensitivity analysis of this procedure; at the production stage—the modeling of energy processes and a sensitivity analysis of the allocation procedures; during building operation—the expected service life of ICB; an analysis concerning the need to consider the thermal diffusivity of ICB in the comparison of the performance of insulation materials. This paper presents the up-to-date “cradle-to-cradle” environmental performance of ICB for the environmental categories and life-cycle stages defined in European standards. PMID:28773516

Comparative durability of timber bridges in the USA

Treesearch

James P. Wacker; Brian K. Brashaw

2017-01-01

As engineers begin to utilize life-cycle-cost design approaches for timber bridges, there is a necessity for more reliable data about their durability and expected service life. This paper summarizes a comprehensive effort to assess the current condition of more than one hundred timber highway bridge superstructures throughout the United States. This national study was...

Fatigue reliability of steel highway bridge details.

DOT National Transportation Integrated Search

2001-08-01

The expected life of a steel highway bridge subjected to random, variable-amplitude traffic cycles is highly dependent on damage accumulation caused by various fatigue mechanisms. This study addressed some of the issues associated with developing pro...

Lithium/disulfide battery R and D

NASA Astrophysics Data System (ADS)

Kaun, T. D.; Deluca, W.; Lee, J.; Redey, L.; Nelson, P. A.

The focus of molten-salt cell R and D in the past year at Argonne National Laboratory has been on developing an understanding of the excellent performance and stability of a lithium/disulfide cell using LiCl-LiBr-KBr electrolyte. For further improvement, we have initiated development of a rod-electrode cell design and design of cells which can tolerate overdischarge and overcharge abuse. Earlier Li/FeS2 cells offered performance quite below expectations and had high capacity decline rates: 0.10 to 0.25 percent per cycle. Approaches for reducing the capacity decline rates of the earlier cells also reduced cell performance. However, our improved Li/FeS2 cell tests indicate good prospects for attaining cell development goals of specific energy of 200 Wh/kg at a 4-h discharge rate, a specific power of 200 W/kg at 80 percent depth of discharge, and a cycle life of 1000 cycles.

Comparison of Battery Life Across Real-World Automotive Drive-Cycles (Presentation)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Smith, K.; Earleywine, M.; Wood, E.

2011-11-01

Laboratories run around-the-clock aging tests to try to understand as quickly as possible how long new Li-ion battery designs will last under certain duty cycles. These tests may include factors such as duty cycles, climate, battery power profiles, and battery stress statistics. Such tests are generally accelerated and do not consider possible dwell time at high temperatures and states-of-charge. Battery life-predictive models provide guidance as to how long Li-ion batteries may last under real-world electric-drive vehicle applications. Worst-case aging scenarios are extracted from hundreds of real-world duty cycles developed from vehicle travel surveys. Vehicles examined included PHEV10 and PHEV40 EDVsmore » under fixed (28 degrees C), limited cooling (forced ambient temperature), and aggressive cooling (20 degrees C chilled liquid) scenarios using either nightly charging or opportunity charging. The results show that battery life expectancy is 7.8 - 13.2 years for the PHEV10 using a nightly charge in Phoenix, AZ (hot climate), and that the 'aggressive' cooling scenario can extend battery life by 1-3 years, while the 'limited' cooling scenario shortens battery life by 1-2 years. Frequent (opportunity) charging can reduce battery life by 1 year for the PHEV10, while frequent charging can extend battery life by one-half year.« less

[Multiple decrement tables of changes in the marital status of the population of Poland (1982-1984)].

PubMed

Kedelski, M; Golata, E

1986-01-01

Official Polish data for the period 1982-1984 are used to construct multiple decrement tables of changes in marital status for the population of a hypothetical cohort over the course of its life history. The data are analyzed separately by sex with respect to the probabilities of change in marital status, the characteristics of the life cycle, and the expectation of life by marital status category. (SUMMARY IN ENG AND RUS)

Low Cycle Fatigue and Creep-Fatigue Behavior of Alloy 617 at High Temperature

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cabet, Celine; Carroll, Laura; Wright, Richard

Alloy 617 is the leading candidate material for an intermediate heat exchanger (IHX) application of the Very High Temperature Nuclear Reactor (VHTR), expected to have an outlet temperature as high as 950 degrees C. Acceptance of Alloy 617 in Section III of the ASME Code for nuclear construction requires a detailed understanding of the creep-fatigue behavior. Initial creep-fatigue work on Alloy 617 suggests a more dominant role of environment with increasing temperature and/or hold times evidenced through changes in creep-fatigue crack growth mechanism/s and failure life. Continuous cycle fatigue and creep-fatigue testing of Alloy 617 was conducted at 950 degreesmore » C and 0.3% and 0.6% total strain in air to simulate damage modes expected in a VHTR application. Continuous cycle specimens exhibited transgranular cracking. Intergranular cracking was observed in the creep-fatigue specimens, although evidence of grain boundary cavitation was not observed. Despite the absence of grain boundary cavitation to accelerate crack propagation, the addition of a hold time at peak tensile strain was detrimental to cycle life. This suggests that creepfatigue interaction may occur by a different mechanism or that the environment may be partially responsible for accelerating failure.« less

Life Cycle Testing of Viscoelastic Material for Hubble Space Telescope Solar Array 3 Damper

NASA Technical Reports Server (NTRS)

Maly, Joseph R.; Reed, Benjamin B.; Viens, Michael J.; Parker, Bradford H.; Pendleton, Scott C.

2003-01-01

During the March 2002 Servicing Mission by Space Shuttle (STS 109), the Hubble Space Telescope (HST) was refurbished with two new solar arrays that now provide all of its power. These arrays were built with viscoelastic/titanium dampers, integral to the supporting masts, which reduce the interaction of the wing bending modes with the Telescope. Damping of over 3% of critical was achieved. To assess the damper s ability to maintain nominal performance over the 10-year on-orbit design goal, material specimens were subjected to an accelerated life test. The test matrix consisted of scheduled events to expose the specimens to pre-determined combinations of temperatures, frequencies, displacement levels, and numbers of cycles. These exposure events were designed to replicate the life environment of the damper from fabrication through testing to launch and life on-orbit. To determine whether material degradation occurred during the exposure sequence, material performance was evaluated before and after the accelerated aging with complex stiffness measurements. Based on comparison of pre- and post-life-cycle measurements, the material is expected to maintain nominal performance through end of life on-orbit. Recent telemetry from the Telescope indicates that the dampers are performing nominally.

From stage to age in variable environments: life expectancy and survivorship.

PubMed

Tuljapurkar, Shripad; Horvitz, Carol C

2006-06-01

Stage-based demographic data are now available on many species of plants and some animals, and they often display temporal and spatial variability. We provide exact formulas to compute age-specific life expectancy and survivorship from stage-based data for three models of temporal variability: cycles, serially independent random variation, and a Markov chain. These models provide a comprehensive description of patterns of temporal variation. Our formulas describe the effects of cohort (birth) environmental condition on mortality at all ages, and of the effects on survivorship of environmental variability experienced over the course of life. This paper complements existing methods for time-invariant stage-based data, and adds to the information on population growth and dynamics available from stochastic demography.

Economics of solar energy: Short term costing

NASA Astrophysics Data System (ADS)

Klee, H.

The solar economics based on life cycle costs are refuted as both imaginary and irrelevant. It is argued that predicting rates of inflation and fuel escalation, expected life, maintenance costs, and legislation over the next ten to twenty years is pure guesswork. Furthermore, given the high mobility level of the U.S. population, the average consumer is skeptical of long run arguments which will pay returns only to the next owners. In the short term cost analysis, the house is sold prior to the end of the expected life of the system. The cash flow of the seller and buyer are considered. All the relevant factors, including the federal tax credit and the added value of the house because of the solar system are included.

Environmental impacts of lighting technologies - Life cycle assessment and sensitivity analysis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Welz, Tobias; Hischier, Roland, E-mail: Roland.Hischier@empa.ch; Hilty, Lorenz M.

2011-04-15

With two regulations, 244/2009 and 245/2009, the European Commission recently put into practice the EuP Directive in the area of lighting devices, aiming to improve energy efficiency in the domestic lighting sector. This article presents a comprehensive life cycle assessment comparison of four different lighting technologies: the tungsten lamp, the halogen lamp, the conventional fluorescent lamp and the compact fluorescent lamp. Taking advantage of the most up-to-date life cycle inventory database available (ecoinvent data version 2.01), all life cycle phases were assessed and the sensitivity of the results for varying assumptions analysed: different qualities of compact fluorescent lamps (production phase),more » different electricity mixes (use phase), and end-of-life scenarios for WEEE recycling versus municipal solid waste incineration (disposal phase). A functional unit of 'one hour of lighting' was defined and the environmental burdens for the whole life cycle for all four lamp types were calculated, showing a clearly lower impact for the two gas-discharge lamps, i.e. the fluorescent and the compact fluorescent lamp. Differences in the product quality of the compact fluorescent lamps reveal to have only a very small effect on the overall environmental performance of this lamp type; a decline of the actual life time of this lamp type doesn't result in a change of the rank order of the results of the here examined four lamp types. It was also shown that the environmental break-even point of the gas-discharge lamps is reached long before the end of their expected life-span. All in all, it can be concluded that a change from today's tungsten lamp technology to a low-energy-consuming technology such as the compact fluorescent lamp results in a substantial environmental benefit.« less

Lifecycle Verification of Tank Liner Polymers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Anovitz, Lawrence; Smith, Barton

2014-03-01

This report describes a method that was developed for the purpose of assessing the durability of thermoplastic liners used in a Type IV hydrogen storage tank during the tank s expected service life. In the method, a thermoplastic liner specimen is cycled between the maximum and minimum expected working temperatures while it is differentially pressurized with high-pressure hydrogen gas. The number of thermal cycling intervals corresponds to those expected within the tank s design lifetime. At prescribed intervals, hydrogen permeation measurements are done in situ to assess the ability of the liner specimen to maintain its hydrogen barrier properties andmore » to model its permeability over the tank lifetime. Finally, the model is used to assess whether the steady-state leakage rate in the tank could potentially exceed the leakage specification for hydrogen fuel cell passenger vehicles. A durability assessment was performed on a specimen of high-density polyethylene (HDPE) that is in current use as a tank liner. Hydrogen permeation measurements were performed on several additional tank liner polymers as well as novel polymers proposed for use as storage tank liners and hydrogen barrier materials. The following technical barriers from the Fuel Cell Technologies Program MYRDD were addressed by the project: D. Durability of on-board storage systems lifetime of at least 1500 cycles G. Materials of construction vessel containment that is resistant to hydrogen permeation M. Lack of Tank Performance Data and Understanding of Failure Mechanisms And the following technical targets1 for on-board hydrogen storage systems R&D were likewise addressed: Operational cycle life (1/4 tank to full) FY 2017: 1500 cycles; Ultimate: 1500 cycles Environmental health & safety Permeation and leakage: Meets or exceeds applicable standards Loss of useable H2: FY 2017: 0.05 g/h/kg H2; Ultimate: 0.05 g/h/kg H2« less

Sexual dimorphism in immune function changes during the annual cycle in house sparrows

NASA Astrophysics Data System (ADS)

Pap, Péter László; Czirják, Gábor Árpád; Vágási, Csongor István; Barta, Zoltán; Hasselquist, Dennis

2010-10-01

Difference between sexes in parasitism is a common phenomenon among birds, which may be related to differences between males and females in their investment into immune functions or as a consequence of differential exposure to parasites. Because life-history strategies change sex specifically during the annual cycle, immunological responses of the host aiming to reduce the impact of parasites may be sexually dimorphic. Despite the great complexity of the immune system, studies on immunoecology generally characterise the immune status through a few variables, often overlooking potentially important seasonal and gender effects. However, because of the differences in physiological and defence mechanisms among different arms of the immune system, we expect divergent responses of immune components to environmental seasonality. In male and female house sparrows ( Passer domesticus), we measured the major components of the immune system (innate, acquired, cellular and humoral) during four important life-history stages across the year: (1) mating, (2) breeding, (3) moulting and (4) during the winter capture and also following introduction to captivity in aviary. Different individuals were sampled from the same population during the four life cycle stages. We found that three out of eight immune variables showed a significant life cycle stage × sex interaction. The difference in immune response between the sexes was significant in five immune variables during the mating stage, when females had consistently stronger immune function than males, while variables varied generally non-significantly with sex during the remaining three life cycle stages. Our results show that the immune system is highly variable between life cycle stages and sexes, highlighting the potential fine tuning of the immune system to specific physiological states and environmental conditions.

Long-Range Technological Impact on Computer-Aided Product Development at DMA (Defense Mapping Agency).

DTIC Science & Technology

1986-07-01

maintainability, enhanceability, portability, flexibility, reusability of components, expected market or production life span, upward compatibility, integration...cost) but, most often, they involve global marketing and production objectives. A high life- cycle cost may be accepted in exchange for some other...ease of integration. More importantly, these results could be interpreted as suggesting the need to use a mixed approach where one uses a subset of

Stock Market Expectations of Dutch Households

PubMed Central

Hurd, Michael; van Rooij, Maarten; Winter, Joachim

2013-01-01

Despite its importance for the analysis of life-cycle behavior and, in particular, retirement planning, stock ownership by private households is poorly understood. Among other approaches to investigate this puzzle, recent research has started to elicit private households’ expectations of stock market returns. This paper reports findings from a study that collected data over a two-year period both on households’ stock market expectations (subjective probabilities of gains or losses) and on whether they own stocks. We document substantial heterogeneity in financial market expectations. Expectations are correlated with stock ownership. Over the two years of our data, stock market prices increased, and expectations of future stock market price changes also increased, lending support to the view that expectations are influenced by recent stock gains or losses. PMID:23997423

A life cycle assessment of options for producing synthetic fuel via pyrolysis.

PubMed

Vienescu, D N; Wang, J; Le Gresley, A; Nixon, J D

2018-02-01

The aim of this study was to investigate the sustainability of producing synthetic fuels from biomass using thermochemical processing and different upgrading pathways. Life cycle assessment (LCA) models consisting of biomass collection, transportation, pre-treatment, pyrolysis and upgrading stages were developed. To reveal the environmental impacts associated with greater post-processing to achieve higher quality fuels, six different bio-oil upgrading scenarios were analysed and included esterification, ketonisation, hydrotreating and hydrocracking. Furthermore, to take into account the possible ranges in LCA inventory data, expected, optimistic and pessimistic values for producing and upgrading pyrolysis oils were evaluated. We found that the expected carbon dioxide equivalent emissions could be as high as 6000 gCO 2e /kg of upgraded fuel, which is greater than the emissions arising from the use of diesel fuel. Other environmental impacts occurring from the fuel production process are outlined, such as resource depletion, acidification and eutrophication. Copyright © 2017 Elsevier Ltd. All rights reserved.

SOLID WASTE INTEGRATED FORECAST TECHNICAL (SWIFT) REPORT FY2005 THRU FY2035 2005.0 VOLUME 2

DOE Office of Scientific and Technical Information (OSTI.GOV)

BARCOT, R.A.

This report provides up-to-date life cycle information about the radioactive solid waste expected to be managed by Hanford's Waste Management (WM) Project from onsite and offsite generators. It includes: (1) an overview of Hanford-wide solid waste to be managed by the WM Project; (2) multi-level and waste class-specific estimates; (3) background information on waste sources; and (4) comparisons to previous forecasts and other national data sources. The focus of this report is low-level waste (LLW), mixed low-level waste (MLLW), and transuranic waste, both non-mixed and mixed (TRU(M)). Some details on hazardous waste are also provided, however, this information is notmore » considered comprehensive. This report includes data requested in December, 2004 with updates through March 31,2005. The data represent a life cycle forecast covering all reported activities from FY2005 through the end of each program's life cycle and are an update of the previous FY2004.1 data version.« less

Role of formats in the life cycle of data

NASA Technical Reports Server (NTRS)

Sawyer, Don

1993-01-01

This paper's perspective is based on the author's experience generating, analyzing, archiving, and distributing data obtained from satellites, and on the experience gained in data modeling and the development of standards for data understanding under the Consultative Committee for Space Data Systems (CCSDS). Data formats are used to represent all information in digital form, and thus play a major role in all interchanges and access to this information. The need to more efficiently manage and process rapidly growing quantities of data, and to preserve the information contained therein, continue to drive a great interest in data formats. The purpose of this paper is to examine the role of formats as they support the use of data within a space agency. The life-cycle identified is only one of many variations that would be recognized by those familiar with the 'space business', however it is expected that most of the issues raised will be pertinent to other 'space business' life cycles and to other 'non-space' disciplines as well.

EVALUATING THE GREENNESS OF GREEN CHEMISTRY VIA TRADITIONAL AND THERMODYNAMIC LIFE CYCLE ASSESSMENT

EPA Science Inventory

Developments in Green Chemistry are expected to result in novel approaches that are more environmentally benign than traditional methods. Much of the research in green chemistry focuses on replacing toxic and hazardous substances such as solvents, catalysts and reaction media by...

Intra-Company Communication: A Key Element in Marketing Strategy.

ERIC Educational Resources Information Center

Frost, Fred A.

Rapid technological development, rising standards of living, and greater pressures of consumerism and consumer expectations have caused shorter product life cycles. Future organizational success will depend on organizations' abilities to respond to the changing opportunities and threats in the marketplace. As companies and products move through…

Manpower/Hardware Life Cycle Cost Analysis Study.

DTIC Science & Technology

1979-11-06

designer will begin to learn, on a subconscious level, about the likely outcome of tradeoffs. At the high rate of use expected for these machines, he...one requiring considerable cost analytic expertise), and the model must be redocumented and partially or completely reprogrammed . All this is extremely

The gender gap in mortality: How much is explained by behavior?

PubMed

Schünemann, Johannes; Strulik, Holger; Trimborn, Timo

2017-07-01

In developed countries, women are expected to live about 4-5 years longer than men. In this paper, we develop a novel approach to gauge the extent to which gender differences in longevity can be attributed to gender-specific preferences and health behavior. We set up a physiologically founded model of health deficit accumulation and calibrate it using recent insights from gerontology. From fitting life cycle health expenditure and life expectancy, we obtain estimates of the gender-specific preference parameters. We then perform the counterfactual experiment of endowing women with the preferences of men. In our benchmark scenario, this reduces the gender gap in life expectancy from 4.6 to 1.4 years. When we add gender-specific preferences for unhealthy consumption, the model can motivate up to 89 percent of the gender gap. Our theory offers also an economic explanation for why the gender gap declines with rising income. Copyright © 2017 Elsevier B.V. All rights reserved.

A Combined High and Low Cycle Fatigue Model for Life Prediction of Turbine Blades

PubMed Central

Yue, Peng; Yu, Zheng-Yong; Wang, Qingyuan

2017-01-01

Combined high and low cycle fatigue (CCF) generally induces the failure of aircraft gas turbine attachments. Based on the aero-engine load spectrum, accurate assessment of fatigue damage due to the interaction of high cycle fatigue (HCF) resulting from high frequency vibrations and low cycle fatigue (LCF) from ground-air-ground engine cycles is of critical importance for ensuring structural integrity of engine components, like turbine blades. In this paper, the influence of combined damage accumulation on the expected CCF life are investigated for turbine blades. The CCF behavior of a turbine blade is usually studied by testing with four load-controlled parameters, including high cycle stress amplitude and frequency, and low cycle stress amplitude and frequency. According to this, a new damage accumulation model is proposed based on Miner’s rule to consider the coupled damage due to HCF-LCF interaction by introducing the four load parameters. Five experimental datasets of turbine blade alloys and turbine blades were introduced for model validation and comparison between the proposed Miner, Manson-Halford, and Trufyakov-Kovalchuk models. Results show that the proposed model provides more accurate predictions than others with lower mean and standard deviation values of model prediction errors. PMID:28773064

A Combined High and Low Cycle Fatigue Model for Life Prediction of Turbine Blades.

PubMed

Zhu, Shun-Peng; Yue, Peng; Yu, Zheng-Yong; Wang, Qingyuan

2017-06-26

Combined high and low cycle fatigue (CCF) generally induces the failure of aircraft gas turbine attachments. Based on the aero-engine load spectrum, accurate assessment of fatigue damage due to the interaction of high cycle fatigue (HCF) resulting from high frequency vibrations and low cycle fatigue (LCF) from ground-air-ground engine cycles is of critical importance for ensuring structural integrity of engine components, like turbine blades. In this paper, the influence of combined damage accumulation on the expected CCF life are investigated for turbine blades. The CCF behavior of a turbine blade is usually studied by testing with four load-controlled parameters, including high cycle stress amplitude and frequency, and low cycle stress amplitude and frequency. According to this, a new damage accumulation model is proposed based on Miner's rule to consider the coupled damage due to HCF-LCF interaction by introducing the four load parameters. Five experimental datasets of turbine blade alloys and turbine blades were introduced for model validation and comparison between the proposed Miner, Manson-Halford, and Trufyakov-Kovalchuk models. Results show that the proposed model provides more accurate predictions than others with lower mean and standard deviation values of model prediction errors.

Cycle life status of SAFT VOS nickel-cadmium cells

NASA Technical Reports Server (NTRS)

Goualard, Jacques

1993-01-01

The SAFT prismatic VOS Ni-Cd cells have been flown in geosynchronous orbit since 1977 and in low earth orbit since 1983. Parallel cycling tests are performed by several space agencies in order to determine the cycle life for a wide range of temperature and depth of discharge (DOD). In low Earth orbit (LEO), the ELAN program is conducted on 24 Ah cells by CNES and ESA at the European Battery Test Center at temperatures ranging from 0 to 27 C and DOD from 10 to 40 percent. Data are presented up to 37,000 cycles. One pack (X-80) has achieved 49,000 cycles at 10 C and 23 percent DOD. The geosynchronous orbit simulation of a high DOD test is conducted by ESA on 3 batteries at 10 C and 70, 90, and 100 percent DOD. Thirty-one eclipse seasons are completed, and no signs of degradation have been found. The Air Force test at CRANE on 24 Ah and 40 Ah cells at 20 C and 80 percent DOD has achieved 19 shadow periods. Life expectancy is discussed. The VOS cell technology could be used for the following: (1) in geosynchronous conditions--15 yrs at 10-15 C and 80 percent DOD; and (2) in low earth orbit--10 yrs at 5-15 C and 25-30 percent DOD.

Potential release scenarios for carbon nanotubes used in composites

EPA Science Inventory

The expected widespread use of carbon nanotube (CNT)-composites in consumer products calls for an assessment of the possible release and exposure to workers, consumers and the environment. Release of CNTs may occur at all steps in the life cycle of products, but to date only limi...

The total lifetime costs of smoking.

PubMed

Rasmussen, Susanne R; Prescott, Eva; Sørensen, Thorkild I A; Søgaard, Jes

2004-03-01

Net costs of smoking in a lifetime perspective and, hence, the economic interests in antismoking policies have been questioned. It has been proposed that the health-related costs of smoking are balanced by smaller expenditure due to shorter life expectancy. A dynamic (life cycle) method taking differences in life expectancy into account. Main outcome measures were direct and indirect lifetime health costs for ever-smokers and never-smokers, and cost ratios (ever-smokers to never-smokers). The estimations were based on annual disease rates of use of the healthcare services, smoking relative risks, smoking prevalences, and costs. Annual direct and indirect costs of ever-smokers were higher than for never-smokers in all age groups of both genders. The direct and indirect cost ratios were highest at age 45 for women, and at age 35 and 40 for men, respectively. Taking life expectancy differences into account, direct and indirect lifetime health costs for men aged 35, discounted by 5% per year were 66% and 83% higher in ever-smokers than in never-smokers. Corresponding results for women were 74% and 79%, respectively. The results are insensitive to a broad range of relative risk-estimates and discount rates including no discounting. Excess costs of ever-smokers disappear if the inclusion of smoking-related diseases is narrowed to that of previous studies. Smoking imposes costs to society even when taking life expectancy into consideration--both in direct and indirect costs.

Transcriptome profiling of the dynamic life cycle of the scypohozoan jellyfish Aurelia aurita.

PubMed

Brekhman, Vera; Malik, Assaf; Haas, Brian; Sher, Noa; Lotan, Tamar

2015-02-14

The moon jellyfish Aurelia aurita is a widespread scyphozoan species that forms large seasonal blooms. Here we provide the first comprehensive view of the entire complex life of the Aurelia Red Sea strain by employing transcriptomic profiling of each stage from planula to mature medusa. A de novo transcriptome was assembled from Illumina RNA-Seq data generated from six stages throughout the Aurelia life cycle. Transcript expression profiling yielded clusters of annotated transcripts with functions related to each specific life-cycle stage. Free-swimming planulae were found highly enriched for functions related to cilia and microtubules, and the drastic morphogenetic process undergone by the planula while establishing the future body of the polyp may be mediated by specifically expressed Wnt ligands. Specific transcripts related to sensory functions were found in the strobila and the ephyra, whereas extracellular matrix functions were enriched in the medusa due to high expression of transcripts such as collagen, fibrillin and laminin, presumably involved in mesoglea development. The CL390-like gene, suggested to act as a strobilation hormone, was also highly expressed in the advanced strobila of the Red Sea species, and in the medusa stage we identified betaine-homocysteine methyltransferase, an enzyme that may play an important part in maintaining equilibrium of the medusa's bell. Finally, we identified the transcription factors participating in the Aurelia life-cycle and found that 70% of these 487 identified transcription factors were expressed in a developmental-stage-specific manner. This study provides the first scyphozoan transcriptome covering the entire developmental trajectory of the life cycle of Aurelia. It highlights the importance of numerous stage-specific transcription factors in driving morphological and functional changes throughout this complex metamorphosis, and is expected to be a valuable resource to the community.

Evolved Populations of Shigella flexneri Phage Sf6 Acquire Large Deletions, Altered Genomic Architecture, and Faster Life Cycles.

PubMed

Dover, John A; Burmeister, Alita R; Molineux, Ian J; Parent, Kristin N

2016-09-19

Genomic architecture is the framework within which genes and regulatory elements evolve and where specific constructs may constrain or potentiate particular adaptations. One such construct is evident in phages that use a headful packaging strategy that results in progeny phage heads packaged with DNA until full rather than encapsidating a simple unit-length genome. Here, we investigate the evolution of the headful packaging phage Sf6 in response to barriers that impede efficient phage adsorption to the host cell. Ten replicate populations evolved faster Sf6 life cycles by parallel mutations found in a phage lysis gene and/or by large, 1.2- to 4.0-kb deletions that remove a mobile genetic IS911 element present in the ancestral phage genome. The fastest life cycles were found in phages that acquired both mutations. No mutations were found in genes encoding phage structural proteins, which were a priori expected from the experimental design that imposed a challenge for phage adsorption by using a Shigella flexneri host lacking receptors preferred by Sf6. We used DNA sequencing, molecular approaches, and physiological experiments on 82 clonal isolates taken from all 10 populations to reveal the genetic basis of the faster Sf6 life cycle. The majority of our isolates acquired deletions in the phage genome. Our results suggest that deletions are adaptive and can influence the duration of the phage life cycle while acting in conjunction with other lysis time-determining point mutations. © The Author 2016. Published by Oxford University Press on behalf of the Society for Molecular Biology and Evolution.

NUMBER AND TYPE OF OPERATING CYCLES FOR THE FFTF

DOE Office of Scientific and Technical Information (OSTI.GOV)

Boyd, D. C.

1969-05-15

The choice of materials and other vessel design decisions necessary to provide the desired life expectancy for the FTR vessel are partially dependent upon estimates of the number and type of reactor shutdowns and startups which may be anticipated. Current estimates of these so-called "cycles" are given, including scram frequency, experimental outage frequency, standard shutdowns and startups, and rapid controlled shutdowns. Also discussed are abnormal heatup or cooldown, and tentative goals for temperature controls. MTR, ETR, and typical PRTR operating histories are tabulated.

Space system operations and support cost analysis using Markov chains

NASA Technical Reports Server (NTRS)

Unal, Resit; Dean, Edwin B.; Moore, Arlene A.; Fairbairn, Robert E.

1990-01-01

This paper evaluates the use of Markov chain process in probabilistic life cycle cost analysis and suggests further uses of the process as a design aid tool. A methodology is developed for estimating operations and support cost and expected life for reusable space transportation systems. Application of the methodology is demonstrated for the case of a hypothetical space transportation vehicle. A sensitivity analysis is carried out to explore the effects of uncertainty in key model inputs.

Gamma Radiation Sterilization Reduces the High-cycle Fatigue Life of Allograft Bone.

PubMed

Islam, Anowarul; Chapin, Katherine; Moore, Emily; Ford, Joel; Rimnac, Clare; Akkus, Ozan

2016-03-01

Sterilization by gamma radiation impairs the mechanical properties of bone allografts. Previous work related to radiation-induced embrittlement of bone tissue has been limited mostly to monotonic testing which does not necessarily predict the high-cycle fatigue life of allografts in vivo. We designed a custom rotating-bending fatigue device to answer the following questions: (1) Does gamma radiation sterilization affect the high-cycle fatigue behavior of cortical bone; and (2) how does the fatigue life change with cyclic stress level? The high-cycle fatigue behavior of human cortical bone specimens was examined at stress levels related to physiologic levels using a custom-designed rotating-bending fatigue device. Test specimens were distributed among two treatment groups (n = 6/group); control and irradiated. Samples were tested until failure at stress levels of 25, 35, and 45 MPa. At 25 MPa, 83% of control samples survived 30 million cycles (run-out) whereas 83% of irradiated samples survived only 0.5 million cycles. At 35 MPa, irradiated samples showed an approximately 19-fold reduction in fatigue life compared with control samples (12.2 × 10(6) ± 12.3 × 10(6) versus 6.38 × 10(5) ± 6.81 × 10(5); p = 0.046), and in the case of 45 MPa, this reduction was approximately 17.5-fold (7.31 × 10(5) ± 6.39 × 10(5) versus 4.17 × 10(4) ± 1.91 × 10(4); p = 0.025). Equations to estimate high-cycle fatigue life of irradiated and control cortical bone allograft at a certain stress level were derived. Gamma radiation sterilization severely impairs the high cycle fatigue life of structural allograft bone tissues, more so than the decline that has been reported for monotonic mechanical properties. Therefore, clinicians need to be conservative in the expectation of the fatigue life of structural allograft bone tissues. Methods to preserve the fatigue strength of nonirradiated allograft bone tissue are needed. As opposed to what monotonic tests might suggest, the cyclic fatigue life of radiation-sterilized structural allografts is likely severely compromised relative to the nonirradiated condition and therefore should be taken into consideration. Methods to reduce the effect of irradiation or to recover structural allograft bone tissue fatigue strength are important to pursue.

Evaluating the Environmental Impacts of a Nano-Enhanced Field Emission Display Using Life Cycle Assessment: A Screening-Level Study

EPA Science Inventory

Carbon nanotube (CNT) field emission displays (FEDs) are currently in the product development stage and are expected to be commercialized in the near future because they offer image quality and viewing angles comparable to a cathode ray tube (CRT) while using a thinner structure,...

Teaching and Learning in Japan.

ERIC Educational Resources Information Center

Rohlen, Thomas P., Ed.; LeTendre, Gerald K., Ed.

The essays gathered in this volume are united by the common goal of understanding teaching and learning in Japan as it actually occurs. The essays seek to answer questions about the actual conduct of learning in different settings and at different points in the life cycle. This volume explores the expectations and associations found in specific…

Life cycle assessments of bioenergy oilseed production in rotation with dryland cereals in eastern Oregon, USA

USDA-ARS?s Scientific Manuscript database

Oilseed crops are expected to become increasingly important as feedstock for production of renewable jet fuel for the airline industry. However, there are potential social and environmental problems associated with using agricultural land to produce energy crops. The objective of this study was to...

Life Prediction for a CMC Component Using the NASALIFE Computer Code

NASA Technical Reports Server (NTRS)

Gyekenyesi, John Z.; Murthy, Pappu L. N.; Mital, Subodh K.

2005-01-01

The computer code, NASALIFE, was used to provide estimates for life of an SiC/SiC stator vane under varying thermomechanical loading conditions. The primary intention of this effort is to show how the computer code NASALIFE can be used to provide reasonable estimates of life for practical propulsion system components made of advanced ceramic matrix composites (CMC). Simple loading conditions provided readily observable and acceptable life predictions. Varying the loading conditions such that low cycle fatigue and creep were affected independently provided expected trends in the results for life due to varying loads and life due to creep. Analysis was based on idealized empirical data for the 9/99 Melt Infiltrated SiC fiber reinforced SiC.

Qualification of Fiber Optic Cables for Martian Extreme Temperature Environments

NASA Technical Reports Server (NTRS)

Ramesham, Rajeshuni; Lindensmith, Christian A.; Roberts, William T.; Rainen, Richard A.

2011-01-01

Means have been developed for enabling fiber optic cables of the Laser Induced Breakdown Spectrometer instrument to survive ground operations plus the nominal 670 Martian conditions that include Martian summer and winter seasons. The purpose of this development was to validate the use of the rover external fiber optic cabling of ChemCam for space applications under the extreme thermal environments to be encountered during the Mars Science Laboratory (MSL) mission. Flight-representative fiber optic cables were subjected to extreme temperature thermal cycling of the same diurnal depth (or delta T) as expected in flight, but for three times the expected number of in-flight thermal cycles. The survivability of fiber optic cables was tested for 600 cumulative thermal cycles from -130 to +15 C to cover the winter season, and another 1,410 cumulative cycles from -105 to +40 C to cover the summer season. This test satisfies the required 3 times the design margin that is a total of 2,010 thermal cycles (670 x 3). This development test included functional optical transmission tests during the course of the test. Transmission of the fiber optic cables was performed prior to and after 1,288 thermal cycles and 2,010 thermal cycles. No significant changes in transmission were observed on either of the two representative fiber cables subject through the 3X MSL mission life that is 2,010 thermal cycles.

Stochastic variation in avian survival rates: Life-history predictions, population consequences, and the potential responses to human perturbations and climate change

USGS Publications Warehouse

Schmutz, Joel A.; Thomson, David L.; Cooch, Evan G.; Conroy, Michael J.

2009-01-01

Stochastic variation in survival rates is expected to decrease long-term population growth rates. This expectation influences both life-history theory and the conservation of species. From this expectation, Pfister (1998) developed the important life-history prediction that natural selection will have minimized variability in those elements of the annual life cycle (such as adult survival rate) with high sensitivity. This prediction has not been rigorously evaluated for bird populations, in part due to statistical difficulties related to variance estimation. I here overcome these difficulties, and in an analysis of 62 populations, I confirm her prediction by showing a negative relationship between the proportional sensitivity (elasticity) of adult survival and the proportional variance (CV) of adult survival. However, several species deviated significantly from this expectation, with more process variance in survival than predicted. For instance, projecting the magnitude of process variance in annual survival for American redstarts (Setophaga ruticilla) for 25 years resulted in a 44% decline in abundance without assuming any change in mean survival rate. For most of these species with high process variance, recent changes in harvest, habitats, or changes in climate patterns are the likely sources of environmental variability causing this variability in survival. Because of climate change, environmental variability is increasing on regional and global scales, which is expected to increase stochasticity in vital rates of species. Increased stochasticity in survival will depress population growth rates, and this result will magnify the conservation challenges we face.

NASA Human Spaceflight Scenarios - Do All Our Models Still Say No?

NASA Technical Reports Server (NTRS)

Zapata, Edgar

2017-01-01

Historically, NASA human spaceflight planning has included healthy doses of life cycle cost analysis. Planners put projects and their cost estimates in a budget context. Estimated costs became expected budgets. Regardless, real budgets rarely matched expectations. So plans would come and go as NASA canceled projects. New projects would arise and the cycle would begin again. Repeatedly, NASA schedule and performance ambitions come up against costs growing at double-digit rates while budgets barely rise a couple of percent a year. Significant skepticism greets proposed NASA programs at birth, as cost estimates for new projects are traditionally very high, and worse, far off the mark for those carried forward. In this environment the current "capability driven framework" for NASA human spaceflight evolved, where long term life cycle cost analysis are even viewed as possibly counter-productive. Here, a space exploration project, for example the Space Launch System, focuses on immediate goals. A life cycle is that of a project, not a program, and for only that span of time to a near term milestone like a first test launch. Unfortunately, attempting to avoid some pitfalls in long-term life cycle cost analysis breeds others. Government audits have noted that limiting the scope of cost analysis "does not provide the transparency necessary to assess long-term affordability" making it difficult to understand if NASA "is progressing in a cost-effective and affordable manner." Even in this short-term framework, NASA realizes the importance of long-term considerations, that it must "maximize the efficiency and sustainability of the Exploration Systems development programs", that this is "critical to free resources for re-investment...such as other required deep space exploration capabilities." Assuming the value of long-term life cycle cost analysis, where due diligence meets reconnaissance, and accepting past shortcomings, the work here approaches life cycle cost analysis for human spaceflight differently. 1) If costs have traditionally been so high that adding them up is discouraging, are there any new facts on the ground offering paths to significantly lower costs? 2) If NASA's spaceflight budget and process is an over-arching constraint, with its planning limitations favoring short-term outlooks, is there a way to step outside the budget box? 3) If life cycle answers have historically been too uncertain to be useful, is there a process where stakeholders gain valuable insights merely from emphasizing a common understanding around questions? We analyze the potential life cycle cost of assorted NASA human spaceflight architectures - an architecture as a sum of individual systems, working together. With the prior questions of high costs, limited budgets and uncertainties in mind, public private partnerships are central in these architectures. The cost data for current commercial public private partnerships is encouraging, as are cost estimates for future partnership approaches beyond low Earth orbit. Private capital, directly or indirectly, an ingredient of public private partnerships, may be a significant factor in finding a path around the limits of the NASA spaceflight budget. Also, understanding and reviewing the pros, cons and uncertainties of assorted architectures can assist in developing a common understanding around key questions as important if not more so than the numbers and answers. Lastly, a scenario planning technique is briefly explored that can mature a common understanding about the agencies situation at hand and how diverse stakeholders can go forward together. Scenario planning, rather than focusing on answers, places emphasis on stakeholders developing a common understanding about the future. Putting aside costs, this is especially true of questions about sustainability and growth, results, benefits and expectations. While efficiency exercises or analysis look to reduce resources in one place to apply them elsewhere, moving around slices in a pie, scenario planning can get at the heart of the matter, growing the pie, transforming it, and making the pieces relevant. Especially important is the question of sustainability for different scenarios in the broad sense of the word - not just the narrow ability to survive or continue, but also the ability to adapt, prosper and grow.

Environmental assessment of microwaves and the effect of European energy efficiency and waste management legislation.

PubMed

Gallego-Schmid, Alejandro; Mendoza, Joan Manuel F; Azapagic, Adisa

2018-03-15

More than 130 million microwaves are affected by European Union (EU) legislation which is aimed at reducing the consumption of electricity in the standby mode ('Standby Regulation') and at more sustainable management of end-of-life electrical and electronic waste ('WEEE Directive'). While legislation focuses on these two life cycle stages, there is little information on the environmental impacts of the entire life cycle of microwaves. To address this gap, this paper presents a comprehensive life cycle assessment of microwaves and assesses the environmental implications of the Standby Regulation and the WEEE Directive at the EU level. The impacts are first considered at the level of individual appliances and then at the EU level, with the aim of evaluating the potential environmental implications of the full implementation of the above two EU regulations by 2020. The effects of the electricity decarbonisation and the expected increase in the number of microwaves in use have also been considered. The results suggest that implementation of the EU regulation by 2020 will reduce the environmental impacts considered by 4%-9% compared to the current situation. The majority of these reductions is due to the Standby Regulation, with the contribution of the WEEE Directive being small (~0.3%). However, the expected decarbonisation of electricity will result in much higher reductions (6%-24%) for most impact categories. The results also show that the materials used to manufacture the microwaves, the manufacturing process and end-of-life disposal are environmental hot-spots for several impacts, including depletion of abiotic elements. Therefore, efforts to reduce the environmental impacts of a future electricity mix should be combined with the development of specific eco-design regulations for microwaves that stipulate optimisation of resource consumption. Possible future trends, such as shorter lifetimes and limited availability of some resources, make the development of such product regulations more critical. Copyright © 2017 Elsevier B.V. All rights reserved.

Implications of low natural gas prices on life cycle greenhouse gas emissions in the U.S. electricity sector

NASA Astrophysics Data System (ADS)

Jaramillo, P.; Venkatesh, A.; Griffin, M.; Matthews, S.

2012-12-01

Increased production of unconventional natural gas resources in the U.S. has drastically reduced the price of natural gas. While in 2005 prices went above 10/MMBtu, since 2011 they have been below 3/MMBtu. These low prices have encouraged the increase of natural gas utilization in the United States electricity sector. Natural gas can offset coal for power generation, reducing emissions such as greenhouse gases, sulfur and nitrogen oxides. In quantifying the benefit of offsetting coal by using natural gas, life cycle assessment (LCA) studies have shown up to 50% reductions in life cycle greenhouse gas (GHG) emissions can be expected. However, these studies predominantly use limited system boundaries that contain single individual coal and natural gas power plants. They do not consider (regional) fleets of power plants that are dispatched on the basis of their short-run marginal costs. In this study, simplified economic dispatch models (representing existing power plants in a given region) are developed for three U.S. regions - ERCOT, MISO and PJM. These models, along with historical load data are used to determine how natural gas utilization will increase in the short-term due to changes in natural gas price. The associated changes in fuel mix and life cycle GHG emissions are estimated. Results indicate that life cycle GHG emissions may, at best, decrease by 5-15% as a result of low natural gas prices, compared to almost 50% reductions estimated by previous LCAs. This study thus provides more reasonable estimates of potential reductions in GHG emissions from using natural gas instead of coal in the electricity sector in the short-term.

Analysis of the Environmental Impact on Remanufacturing Wind Turbines

NASA Astrophysics Data System (ADS)

Sosa Skrainka, Manuel R.

To deliver clean energy the use of wind turbines is essential. In June 2011 there was an installed wind capacity equivalent to 211,000MW world-wide (WWEA, 2011). By the end of the year 2009 the U.S. had 35,100MW of wind energy installed capacity to generate electricity (AWEA, 2010). This industry has grown in recent years and is expected to grow even more in the future. The environmental impacts that will arise from the increased number of wind turbines and their end-of-life should be addressed, as large amounts of resources will be required to satisfy the current and future market demands for wind turbines. Since future 10MW wind turbines are expected to be as heavy as 1000 tons each, the study of the environmental response of profitable retirement strategies, such as remanufacturing for these machines, must be considered. Because of the increased number of wind turbines and the materials used, this study provides a comparison between the environmental impacts from remanufacturing the components installed inside the nacelle of multi-megawatt wind turbines and wind turbines manufactured using new components. The study methodology is the following: • Describe the life-cycle and the materials and processes employed for the manufacture and remanufacturing for components inside the nacelle. • Identify remanufacturing alternatives for the components inside the nacelle at the end of the expected life-time service of wind turbines. • Evaluate the environmental impacts from the remanufactured components and compare the results with the impacts of the manufacturing of new components using SimaPro. • Conduct sensitivity analysis over the critical parameters of the life cycle assessment • Propose the most environmentally friendly options for the retirement of each major component of wind turbines. After an analysis of the scenarios the goal of the study is to evaluate remanufacturing as an end-of-life option from an environmental perspective for commercial multi-megawatt wind turbines targeted for secondary wind turbine markets.

Prospects for Accelerator Technology

NASA Astrophysics Data System (ADS)

Todd, Alan

2011-02-01

Accelerator technology today is a greater than US$5 billion per annum business. Development of higher-performance technology with improved reliability that delivers reduced system size and life cycle cost is expected to significantly increase the total accelerator technology market and open up new application sales. Potential future directions are identified and pitfalls in new market penetration are considered. Both of the present big market segments, medical radiation therapy units and semiconductor ion implanters, are approaching the "maturity" phase of their product cycles, where incremental development rather than paradigm shifts is the norm, but they should continue to dominate commercial sales for some time. It is anticipated that large discovery-science accelerators will continue to provide a specialty market beset by the unpredictable cycles resulting from the scale of the projects themselves, coupled with external political and economic drivers. Although fraught with differing market entry difficulties, the security and environmental markets, together with new, as yet unrealized, industrial material processing applications, are expected to provide the bulk of future commercial accelerator technology growth.

Performance improvement: an active life cycle product management

NASA Astrophysics Data System (ADS)

Cucchiella, Federica; Gastaldi, Massimo; Lenny Koh, S. C.

2010-03-01

The management of the supply chain has gained importance in many manufacturing firms. Operational flexibility can be considered a crucial weapon to increase competitiveness in a turbulent marketplace. It reflects the ability of a firm to properly and rapidly respond to a variable and dynamic environment. For the firm operating in a fashion sector, the management of the supply chain is even more complex because the product life cycle is shorter than that of the firm operating in a non-fashion sector. The increase of firm flexibility level can be reached through the application of the real option theory inside the firm network. In fact, real option may increase the project value by allowing managers to more efficiently direct the production. The real option application usually analysed in literature does not take into account that the demands of products are well-defined by the product life cycle. Working on a fashion sector, the life cycle pattern is even more relevant because of an expected demand that grows according to a constant rate that does not capture the demand dynamics of the underlying fashion goods. Thus, the primary research objective of this article is to develop a model useful for the management of investments in a supply chain operating in a fashion sector where the system complexity is increased by the low level of unpredictability and stability that is proper of the mood phenomenon. Moreover, unlike the traditional model, a real option framework is presented here that considers fashion product characterised by uncertain stages of the production cycle.

Long-Term Effects of Tetanus Toxoid Inoculation on the Demography and Life Expectancy of the Cayo Santiago Rhesus Macaques

PubMed Central

KESSLER, MATTHEW J.; PACHECO, RAISA HERNÁNDEZ; RAWLINS, RICHARD G.; RUIZ-LAMBRIDES, ANGELINA; DELGADO, DIANA L.; SABAT, ALBERTO M.

2014-01-01

Tetanus was a major cause of mortality in the free-ranging population of rhesus monkeys on Cayo Santiago prior to 1985 when the entire colony was given its first dose of tetanus toxoid. The immediate reduction in mortality that followed tetanus toxoid inoculation (TTI) has been documented, but the long-term demographic effects of eliminating tetanus infections have not. This study uses the Cayo Santiago demographic database to construct comparative life tables 12 years before, and 12 years after, TTI. Life tables and matrix projection models are used to test for differences in: (i) survival among all individuals as well as among social groups, (ii) long-term fitness of the population, (iii) age distribution, (iv) reproductive value, and (v) life expectancy. A retrospective life table response experiment (LTRE) was performed to determine which life cycle transition contributed most to observed changes in long-term fitness of the population post-TTI. Elimination of clinical tetanus infections through mass inoculation improved the health and well-being of the monkeys. It also profoundly affected the population by increasing survivorship and long-term fitness, decreasing the differences in survival rates among social groups, shifting the population’s age distribution towards older individuals, and increasing reproductive value and life expectancy. These findings are significant because they demonstrate the long-term effects of eradicating a major cause of mortality at a single point in time on survival, reproduction, and overall demography of a naturalistic population of primates. PMID:25230585

Status of nickel/zinc and nickel/iron battery technology for electric vehicle applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yao, N.P.; Christianson, C.C.; Elliott, R.C.

1980-01-01

Significant progress in nickel/zinc and nickel/iron technology has been made towards achieving the battery technical performance goals necessary for widespread use of these battery systems in electric vehicle applications. This progress is reviewed. Nickel/zinc module test data have shown a specific energy of nearly 70 Whr/kg and a specific power of 130 W/kg. However, cycle life improvements are still needed (presently demonstrated capability of 120 cycles) and are expected to be demonstrated during 1980. Nickel/iron modules have demonstrated a specific energy of nearly 50 Wh/kg and a specific power of 100 W/kg. Indications are that improved performance in these areasmore » can be shown during 1980. Nickel/iron modules cycle lives of 300 have been achieved during early 1980 and testing continues. Energy efficiency has been improved from less than 50% to over 65%. Cost reduction (both initial and operating) continues to receive major emphasis at developers of both nickel/zinc and nickel/iron batteries in order to achieve the lowest possible life cycle cost to the battery user.« less

Lead-acid batteries for micro- and mild-hybrid applications

NASA Astrophysics Data System (ADS)

Valenciano, J.; Fernández, M.; Trinidad, F.; Sanz, L.

Car manufactures have announced the launch in coming months of vehicles with reduced emissions due to the introduction of new functions like stop-start and regenerative braking. Initial performance request of automotive lead-acid batteries are becoming more and more demanding and, in addition to this, cycle life with new accelerated ageing profiles are being proposed in order to determine the influence of the new functions on the expected battery life. This paper will show how different lead-acid battery technologies comply with these new demands, from an improved version of the conventional flooded SLI battery to the high performance of spiral wound valve-regulated lead-acid (VRLA) battery. Different approaches have been studied for improving conventional flooded batteries, i.e., either by the addition of new additives for reducing electrolyte stratification or by optimisation of the battery design to extend cycling life in partial state of charge conditions. With respect to VRLA technology, two different battery designs have been compared. Spiral wound design combines excellent power capability and cycle life under different depth of discharge (DoD) cycling conditions, but flat plate design outperform the latter in energy density due to better utilization of the space available in a prismatic enclosure. This latter design is more adequate for high end class vehicles with high electrical energy demand, whereas spiral wound is better suited for high power/long life demand of commercial vehicle. High temperature behaviour (75 °C) is rather poor for both designs due to water loss, and then VRLA batteries should preferably be located out of the engine compartment.

Volvo Penta 4.3 GL E15 Emissions and Durability Test

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zoubul, G.; Cahoon, M.; Kolb, R.

2011-10-01

A new Volvo Penta carbureted 4.3 GL engine underwent emissions and dynamometer durability testing from break-in to expected end of life using an accelerated ICOMIA marine emissions cycle and E15 fuel. Only ethanol content was controlled. All aging used splash-blended E15 fuel. Exhaust emissions, exhaust gas temperature, torque, power, barometric pressure, air temperature, and fuel flow were measured at five intervals using site-blended E15 aging fuel and certification fuel (E0). The durability test cycle showed no noticeable impact on mechanical durability or engine power. Emissions performance degraded beyond the certification limit for this engine family, mostly occurring by 28% ofmore » expected life. Such degradation is inconsistent with prior experience. Comparisons showed that E15 resulted in lower CO and HC, but increased NOX, as expected for non-feedback-controlled carbureted engines with increased oxygen in the fuel. Fuel consumption also increased with E15 compared with E0. Throughout testing, poor starting characteristics were exhibited on E15 fuel for hot re-start and cold-start. Cranking time to start and smooth idle was roughly doubled compared with typical E0 operation. The carburetor was factory-set for lean operation to ensure emissions compliance. Test protocols did not include carburetor adjustment to account for increased oxygen in the E15 fuel.« less

Analysis of the Global Warming Potential of Biogenic CO2 Emission in Life Cycle Assessments

NASA Astrophysics Data System (ADS)

Liu, Weiguo; Zhang, Zhonghui; Xie, Xinfeng; Yu, Zhen; von Gadow, Klaus; Xu, Junming; Zhao, Shanshan; Yang, Yuchun

2017-01-01

Biomass is generally believed to be carbon neutral. However, recent studies have challenged the carbon neutrality hypothesis by introducing metric indicators to assess the global warming potential of biogenic CO2 (GWPbio). In this study we calculated the GWPbio factors using a forest growth model and radiative forcing effects with a time horizon of 100 years and applied the factors to five life cycle assessment (LCA) case studies of bioproducts. The forest carbon change was also accounted for in the LCA studies. GWPbio factors ranged from 0.13-0.32, indicating that biomass could be an attractive energy resource when compared with fossil fuels. As expected, short rotation and fast-growing biomass plantations produced low GWPbio. Long-lived wood products also allowed more regrowth of biomass to be accounted as absorption of the CO2 emission from biomass combustion. The LCA case studies showed that the total life cycle GHG emissions were closely related to GWPbio and energy conversion efficiency. By considering the GWPbio factors and the forest carbon change, the production of ethanol and bio-power appeared to have higher GHG emissions than petroleum-derived diesel at the highest GWPbio.

Rock Smelting of Copper Ores with Waste Heat Recovery

NASA Astrophysics Data System (ADS)

Norgate, Terry; Jahanshahi, Sharif; Haque, Nawshad

It is generally recognised that the grades of metallic ores are falling globally. This trend can be expected to increase the life cycle-based energy requirement for primary metal production due to the additional amount of material that must be handled and treated in the mining and mineral processing stages of the metal production life cycle. Rock (or whole ore) smelting has been suggested as a possible alternative processing route for low grade ores with a potentially lower energy intensity and environmental impact than traditional processing routes. In this processing route, the beneficiation stage is eliminated along with its associated energy consumption and greenhouse gas emissions, but this is partially offset by the need for more solid material to be handled and heated up to smelting temperatures. A life cycle assessment study was carried out to assess the potential energy and greenhouse gas benefits of a conceptual flowsheet of the rock smelting process, using copper ore as an example. Recovery and utilisation of waste heat in the slag (via dry slag granulation) and offgas streams from the smelting step was also included in the study, with the waste heat being utilised either for thermal applications or electricity generation.

Analysis of the Global Warming Potential of Biogenic CO2 Emission in Life Cycle Assessments

PubMed Central

Liu, Weiguo; Zhang, Zhonghui; Xie, Xinfeng; Yu, Zhen; von Gadow, Klaus; Xu, Junming; Zhao, Shanshan; Yang, Yuchun

2017-01-01

Biomass is generally believed to be carbon neutral. However, recent studies have challenged the carbon neutrality hypothesis by introducing metric indicators to assess the global warming potential of biogenic CO2 (GWPbio). In this study we calculated the GWPbio factors using a forest growth model and radiative forcing effects with a time horizon of 100 years and applied the factors to five life cycle assessment (LCA) case studies of bioproducts. The forest carbon change was also accounted for in the LCA studies. GWPbio factors ranged from 0.13–0.32, indicating that biomass could be an attractive energy resource when compared with fossil fuels. As expected, short rotation and fast-growing biomass plantations produced low GWPbio. Long-lived wood products also allowed more regrowth of biomass to be accounted as absorption of the CO2 emission from biomass combustion. The LCA case studies showed that the total life cycle GHG emissions were closely related to GWPbio and energy conversion efficiency. By considering the GWPbio factors and the forest carbon change, the production of ethanol and bio-power appeared to have higher GHG emissions than petroleum-derived diesel at the highest GWPbio. PMID:28045111

Analysis of the Global Warming Potential of Biogenic CO2 Emission in Life Cycle Assessments.

PubMed

Liu, Weiguo; Zhang, Zhonghui; Xie, Xinfeng; Yu, Zhen; von Gadow, Klaus; Xu, Junming; Zhao, Shanshan; Yang, Yuchun

2017-01-03

Biomass is generally believed to be carbon neutral. However, recent studies have challenged the carbon neutrality hypothesis by introducing metric indicators to assess the global warming potential of biogenic CO 2 (GWP bio ). In this study we calculated the GWP bio factors using a forest growth model and radiative forcing effects with a time horizon of 100 years and applied the factors to five life cycle assessment (LCA) case studies of bioproducts. The forest carbon change was also accounted for in the LCA studies. GWP bio factors ranged from 0.13-0.32, indicating that biomass could be an attractive energy resource when compared with fossil fuels. As expected, short rotation and fast-growing biomass plantations produced low GWP bio . Long-lived wood products also allowed more regrowth of biomass to be accounted as absorption of the CO 2 emission from biomass combustion. The LCA case studies showed that the total life cycle GHG emissions were closely related to GWP bio and energy conversion efficiency. By considering the GWP bio factors and the forest carbon change, the production of ethanol and bio-power appeared to have higher GHG emissions than petroleum-derived diesel at the highest GWP bio .

Evaluating the fate of mercury and other metals across the life-cycle stages from the use of FGD gypsum for wallboard production

EPA Science Inventory

In 2007, 12.3 million tons of flue gas desulfurization (FGD) gypsum was produced due to air emission controls at coal-fired power plants. With increasing use of wet scrubbers in response to more stringent air pollution control requirements, FGD gypsum production is expected to in...

Evaluating Data Clustering Approach for Life-Cycle Facility Control

DTIC Science & Technology

2013-04-01

produce 90% matching accuracy with noise/variations up to 55%. KEYWORDS: Building Information Modelling ( BIM ), machine learning, pattern detection...reconciled to building information model elements and ultimately to an expected resource utilization schedule. The motivation for this integration is to...by interoperable data sources and building information models . Building performance modelling and simulation efforts such as those by Maile et al

Integrating legal liabilities in nanomanufacturing risk management.

PubMed

Mohan, Mayank; Trump, Benjamin D; Bates, Matthew E; Monica, John C; Linkov, Igor

2012-08-07

Among other things, the wide-scale development and use of nanomaterials is expected to produce costly regulatory and civil liabilities for nanomanufacturers due to lingering uncertainties, unanticipated effects, and potential toxicity. The life-cycle environmental, health, and safety (EHS) risks of nanomaterials are currently being studied, but the corresponding legal risks have not been systematically addressed. With the aid of a systematic approach that holistically evaluates and accounts for uncertainties about the inherent properties of nanomaterials, it is possible to provide an order of magnitude estimate of liability risks from regulatory and litigious sources based on current knowledge. In this work, we present a conceptual framework for integrating estimated legal liabilities with EHS risks across nanomaterial life-cycle stages using empirical knowledge in the field, scientific and legal judgment, probabilistic risk assessment, and multicriteria decision analysis. Such estimates will provide investors and operators with a basis to compare different technologies and practices and will also inform regulatory and legislative bodies in determining standards that balance risks with technical advancement. We illustrate the framework through the hypothetical case of a manufacturer of nanoscale titanium dioxide and use the resulting expected legal costs to evaluate alternative risk-management actions.

Bridging the Millennial Generation Expectation Gap: Perspectives and Strategies for Physician and Interprofessional Faculty.

PubMed

Williams, Valerie N; Medina, Jose; Medina, Andria; Clifton, Shari

2017-02-01

Assigning attributes to a birth cohort is one way we identify society-wide, shared life experiences within a group collectively called a "generation." Such assigned attributes influence society's adoption of generation-based expectations held by and about people from a particular birth cohort. Census data and generational attributes inform perspectives on millennial generation birth cohort experiences and engagement as students. The eldest living generation in U.S. society has given way to 3 subsequent generations, the youngest of which is called the millennial generation. What generational attributes influence the effectiveness of teaching and learning between millennial learners and faculty members from other generations? Understanding the role of life cycle effects, period effects and cohort effects can offer medical and health professions educators' insights into different strategies for learner engagement. Discussion includes specific strategies and teaching tactics faculty members can use to engage millennials across a continuum of learning to bridge the "expectation gap." Copyright © 2017 Southern Society for Clinical Investigation. Published by Elsevier Inc. All rights reserved.

Long-term medical costs and life expectancy of acute myeloid leukemia: a probabilistic decision model.

PubMed

Wang, Han-I; Aas, Eline; Howell, Debra; Roman, Eve; Patmore, Russell; Jack, Andrew; Smith, Alexandra

2014-03-01

Acute myeloid leukemia (AML) can be diagnosed at any age and treatment, which can be given with supportive and/or curative intent, is considered expensive compared with that for other cancers. Despite this, no long-term predictive models have been developed for AML, mainly because of the complexities associated with this disease. The objective of the current study was to develop a model (based on a UK cohort) to predict cost and life expectancy at a population level. The model developed in this study combined a decision tree with several Markov models to reflect the complexity of the prognostic factors and treatments of AML. The model was simulated with a cycle length of 1 month for a time period of 5 years and further simulated until age 100 years or death. Results were compared for two age groups and five different initial treatment intents and responses. Transition probabilities, life expectancies, and costs were derived from a UK population-based specialist registry-the Haematological Malignancy Research Network (www.hmrn.org). Overall, expected 5-year medical costs and life expectancy ranged from £8,170 to £81,636 and 3.03 to 34.74 months, respectively. The economic and health outcomes varied with initial treatment intent, age at diagnosis, trial participation, and study time horizon. The model was validated by using face, internal, and external validation methods. The results show that the model captured more than 90% of the empirical costs, and it demonstrated good fit with the empirical overall survival. Costs and life expectancy of AML varied with patient characteristics and initial treatment intent. The robust AML model developed in this study could be used to evaluate new diagnostic tools/treatments, as well as enable policy makers to make informed decisions. Copyright © 2014 International Society for Pharmacoeconomics and Outcomes Research (ISPOR). Published by Elsevier Inc. All rights reserved.

Determining system boundaries on commercial broiler chicken production system using ISO 14040/14044 guideline: A case Study

NASA Astrophysics Data System (ADS)

Sidek, ‘A. A.; Suffian, S. A.; Al-Hazza, M. H. F.; Yusof, H. M.

2018-01-01

The demand of poultry product in Malaysia market shows an escalation throughout the year and expected to increase in the future. The expansion of poultry production has led to environmental concern in relation to their operational impact to environmentAt present, assessment of waste management of poultry production in Malaysia is lacking. A case study research was conducted in a commercial broiler farm to identify and assess the system boundaries in the lifecycle supply chain of broiler chicken production using ISO 14040/44 guidelines. ISO 14040/44 standard includes Life Cycle Assessment (LCA) framework guidelines to evaluate environmental influence associated with a product/process throughout its life span. All attributes associated with broiler operation is defined and the system boundaries is determined to identify possible inputs and outputs in the case study. This paper discuss the initial stage in the LCA process, which set the context of the research and prepare for the stage of Life Cycle Inventory.

Reliability and Qualification of Hardware to Enhance the Mission Assurance of JPL/NASA Projects

NASA Technical Reports Server (NTRS)

Ramesham, Rajeshuni

2010-01-01

Packaging Qualification and Verification (PQV) and life testing of advanced electronic packaging, mechanical assemblies (motors/actuators), and interconnect technologies (flip-chip), platinum temperature thermometer attachment processes, and various other types of hardware for Mars Exploration Rover (MER)/Mars Science Laboratory (MSL), and JUNO flight projects was performed to enhance the mission assurance. The qualification of hardware under extreme cold to hot temperatures was performed with reference to various project requirements. The flight like packages, assemblies, test coupons, and subassemblies were selected for the study to survive three times the total number of expected temperature cycles resulting from all environmental and operational exposures occurring over the life of the flight hardware including all relevant manufacturing, ground operations, and mission phases. Qualification/life testing was performed by subjecting flight-like qualification hardware to the environmental temperature extremes and assessing any structural failures, mechanical failures or degradation in electrical performance due to either overstress or thermal cycle fatigue. Experimental flight qualification test results will be described in this presentation.

Buffer thermal energy storage for a solar thermal powered 1-MW sub e electrical plant

NASA Astrophysics Data System (ADS)

Polzien, R. E.

The application of a latent heat thermal energy buffer storage (TEBS) subsystem to the small community solar thermal power experiment (SCSE) is discussed. The SCSE is a 1-MW sub e solar thermal electric plant consisting of multiple paraboloidal concentrators with an organic Rankine cycle power conversion unit mounted at the focus of each concentrator. Objective of the TEBS is to minimize plant shutdowns during intermittent cloud coverage thereby improving life expectancy of major subsystems. An SCSE plant performance model is used with time varying insolation to show that 70 to 80 percent of the potential engine shutdowns may be averted with the TEBS system. Parametric variation of engine life dependency on start/stop cycles shows the potential for a 4 percent reduction in levelized bus bar energy cost using TEBS.

Long-term effects of tetanus toxoid inoculation on the demography and life expectancy of the Cayo Santiago rhesus macaques.

PubMed

Kessler, Matthew J; Hernández Pacheco, Raisa; Rawlins, Richard G; Ruiz-Lambrides, Angelina; Delgado, Diana L; Sabat, Alberto M

2015-02-01

Tetanus was a major cause of mortality in the free-ranging population of rhesus monkeys on Cayo Santiago prior to 1985 when the entire colony was given its first dose of tetanus toxoid. The immediate reduction in mortality that followed tetanus toxoid inoculation (TTI) has been documented, but the long-term demographic effects of eliminating tetanus infections have not. This study uses the Cayo Santiago demographic database to construct comparative life tables 12 years before, and 12 years after, TTI. Life tables and matrix projection models are used to test for differences in: (i) survival among all individuals as well as among social groups, (ii) long-term fitness of the population, (iii) age distribution, (iv) reproductive value, and (v) life expectancy. A retrospective life table response experiment (LTRE) was performed to determine which life cycle transition contributed most to observed changes in long-term fitness of the population post-TTI. Elimination of clinical tetanus infections through mass inoculation improved the health and well-being of the monkeys. It also profoundly affected the population by increasing survivorship and long-term fitness, decreasing the differences in survival rates among social groups, shifting the population's age distribution towards older individuals, and increasing reproductive value and life expectancy. These findings are significant because they demonstrate the long-term effects of eradicating a major cause of mortality at a single point in time on survival, reproduction, and overall demography of a naturalistic population of primates. © 2014 Wiley Periodicals, Inc.

Life cycle costing as a decision making tool for technology acquisition in radio-diagnosis

PubMed Central

Chakravarty, Abhijit; Debnath, Jyotindu

2014-01-01

Background Life cycle costing analysis is an emerging conceptual tool to validate capital investment in healthcare. Methods A preliminary study was done to analyze the long-term cost impact of acquiring a new 3 T MRI system when compared to technological upgradation of the existing 1.5 T MRI system with a view to evolve a decision matrix for correct investment planning and technology management. Operating costing method was utilized to estimate cost per unit MRI scan, costing inputs were considered for the existing 1.5 T and the proposed 3 T machine. Cost for each expected year in the life span of both 1.5 T and 3 T MRI scan options were then discounted to its Net Present Value. Net Present Value thus calculated for both the alternative options of 1.5 T and 3 T MRI machine was charted along with various intangible but critical Figures of Merit (FOM) to create a decision matrix for capital investment planning. Result Considering all fixed and variable costs contributing towards assumed operation, unit cost per MRI procedure was found to be Rs. 4244.58 for the 1.5 T upgrade and Rs. 6059.37 for the new 3 T MRI machine. Life Cycle Cost Analysis of the proposed 1.5 T upgrade and new 3 T machine showed a Net Present Value of Rs. 42,148,587.80 and Rs. 27,587,842.38 respectively. Conclusion The utility of life cycle costing as a strategic decision making tool towards evaluating alternative options for capital investment planning in health care environment is reiterated. PMID:25609862

Bamboo-Dominated Forests of the Southwest Amazon: Detection, Spatial Extent, Life Cycle Length and Flowering Waves

PubMed Central

de Carvalho, Anelena L.; Nelson, Bruce W.; Bianchini, Milton C.; Plagnol, Daniela; Kuplich, Tatiana M.; Daly, Douglas C.

2013-01-01

We map the extent, infer the life-cycle length and describe spatial and temporal patterns of flowering of sarmentose bamboos (Guadua spp) in upland forests of the southwest Amazon. We first examine the spectra and the spectral separation of forests with different bamboo life stages. False-color composites from orbital sensors going back to 1975 are capable of distinguishing life stages. These woody bamboos flower produce massive quantities of seeds and then die. Life stage is synchronized, forming a single cohort within each population. Bamboo dominates at least 161,500 km2 of forest, coincident with an area of recent or ongoing tectonic uplift, rapid mechanical erosion and poorly drained soils rich in exchangeable cations. Each bamboo population is confined to a single spatially continuous patch or to a core patch with small outliers. Using spatial congruence between pairs of mature-stage maps from different years, we estimate an average life cycle of 27–28 y. It is now possible to predict exactly where and approximately when new bamboo mortality events will occur. We also map 74 bamboo populations that flowered between 2001 and 2008 over the entire domain of bamboo-dominated forest. Population size averaged 330 km2. Flowering events of these populations are temporally and/or spatially separated, restricting or preventing gene exchange. Nonetheless, adjacent populations flower closer in time than expected by chance, forming flowering waves. This may be a consequence of allochronic divergence from fewer ancestral populations and suggests a long history of widespread bamboo in the southwest Amazon. PMID:23359438

Development and application of EEAST: a life cycle based model for use of harvested rainwater and composting toilets in buildings.

PubMed

Devkota, J; Schlachter, H; Anand, C; Phillips, R; Apul, Defne

2013-11-30

Harvested rainwater systems and composting toilets are expected to be an important part of sustainable solutions in buildings. Yet, to this date, a model evaluating their economic and environmental impact has been missing. To address this need, a life cycle based model, EEAST was developed. EEAST was designed to compare the business as usual (BAU) case of using potable water for toilet flushing and irrigation to alternative scenarios of rainwater harvesting and composting toilet based technologies. In EEAST, building characteristics, occupancy, and precipitation are used to size the harvested rainwater and composting toilet systems. Then, life cycle costing and life cycle assessment methods are used to estimate cost, energy, and greenhouse gas (GHG) emission payback periods (PPs) for five alternative scenarios. The scenarios modeled include use of harvested rainwater for toilet flushing, for irrigation, or both; and use of composting toilets with or without harvested rainwater use for irrigation. A sample simulation using EEAST showed that for the office building modeled, the cost PPs were greater than energy PPs which in turn were greater than GHG emission PPs. This was primarily due to energy and emission intensive nature of the centralized water and wastewater infrastructure. The sample simulation also suggested that the composting toilets may have the best performance in all criteria. However, EEAST does not explicitly model solids management and as such may give composting toilets an unfair advantage compared to flush based toilets. EEAST results were found to be very sensitive to cost values used in the model. With the availability of EEAST, life cycle cost, energy, and GHG emissions can now be performed fairly easily by building designers and researchers. Future work is recommended to further improve EEAST and evaluate it for different types of buildings and climates so as to better understand when composting toilets and harvested rainwater systems outperform the BAU case in building design. Copyright © 2013 Elsevier Ltd. All rights reserved.

Cycle life testing of lithium-ion batteries for small satellite LEO space missions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mayer, S.T.; Feikert, J.H.; Kaschmitter, J.L.

1993-08-16

In 1990, Sony corporation announced their intention to manufacture a rechargeable lithium ion battery, based on the intercalation of lithium ions into a carbonaceous anode. The cells were first introduced for portable telephone use in June, 1991. (1) A 3.6V average cell voltage (4.1-2.75V range); (2) Excellent cycle life (1200 @ 100% DOD); (3) Good capacity retention (70% after 6 months); (4) Wide temperature range performance ({minus}20 to +60{degrees}C); (5) Excellent Discharge rate (82% capacity at 30 min. discharge rate); (6) Excellent Charge rate (100% Charge in <3 hrs); and (7) High energy density (264 W*hr/1 and 120 Whr/kg formore » ``D`` size cell. These specifications show significant promise for application of these batteries in low earth orbit (LEO) small satellites, particularly when compared to existing NiH{sub 2} and NiCd technology. The very high energy density and specific energy will reduce power system volume and weight. The wide temperature range enables simpler thermal design, particularly for new, small, high power satellites. The materials used in the lithium ion batteries are relatively inexpensive and benign, so that we expect costs to come down substantially in the future. The specified cycle life at 100% DOD is also 50% longer than most NiCds, so low DOD (depth of discharge) performance could be substantial. This study was undertaken to: (a) assess the feasibility for using lithium ion cells on small satellite LEO missions and (b) verify the claims of the manufacturer. This was accomplished by performing a detailed autopsy and various depth of discharge and rate tests on the cells. Of special interest was the cycle life performance of these cell at various depths of discharge DOD`s, to get an initial measure of the reduction in capacity fade with cycle conditions. Low DOD`s are used to extend the life of all batteries used in a space application.« less

Acquiring Technical Data With Renewable Real Options

DTIC Science & Technology

2016-04-30

Development, and Engineering Center, 2009). Faced with diminishing sources for M2 .50 caliber machine gun parts , an Army engineering center entered the...data needed for life cycle sustainment functions such as maintenance or competitive spare parts procurement, but this expectation is more complicated...than it seems (DoD, 2015). The needs and timing for competitive spare parts procurement are uncertain, and changes in system configuration or

Comparison of carbon footprints of steel versus concrete pipelines for water transmission.

PubMed

Chilana, Lalit; Bhatt, Arpita H; Najafi, Mohammad; Sattler, Melanie

2016-05-01

The global demand for water transmission and service pipelines is expected to more than double between 2012 and 2022. This study compared the carbon footprint of the two most common materials used for large-diameter water transmission pipelines, steel pipe (SP) and prestressed concrete cylinder pipe (PCCP). A planned water transmission pipeline in Texas was used as a case study. Four life-cycle phases for each material were considered: material production and pipeline fabrication, pipe transportation to the job site, pipe installation in the trench, and operation of the pipeline. In each phase, the energy consumed and the CO2-equivalent emissions were quantified. It was found that pipe manufacturing consumed a large amount of energy, and thus contributed more than 90% of life cycle carbon emissions for both kinds of pipe. Steel pipe had 64% larger CO2-eq emissions from manufacturing compared to PCCP. For the transportation phase, PCCP consumed more fuel due to its heavy weight, and therefore had larger CO2-eq emissions. Fuel consumption by construction equipment for installation of pipe was found to be similar for steel pipe and PCCP. Overall, steel had a 32% larger footprint due to greater energy used during manufacturing. This study compared the carbon footprint of two large-diameter water transmission pipeline materials, steel and prestressed concrete cylinder, considering four life-cycle phases for each. The study provides information that project managers can incorporate into their decision-making process concerning pipeline materials. It also provides information concerning the most important phases of the pipeline life cycle to target for emission reductions.

Representativeness of environmental impact assessment methods regarding Life Cycle Inventories.

PubMed

Esnouf, Antoine; Latrille, Éric; Steyer, Jean-Philippe; Helias, Arnaud

2018-04-15

Life Cycle Assessment (LCA) characterises all the exchanges between human driven activities and the environment, thus representing a powerful approach for tackling the environmental impact of a production system. However, LCA practitioners must still choose the appropriate Life Cycle Impact Assessment (LCIA) method to use and are expected to justify this choice: impacts should be relevant facing the concerns of the study and misrepresentations should be avoided. This work aids practitioners in evaluating the adequacy between the assessed environmental issues and studied production system. Based on a geometrical standpoint of LCA framework, Life Cycle Inventories (LCIs) and LCIA methods were localized in the vector space spanned by elementary flows. A proximity measurement, the Representativeness Index (RI), is proposed to explore the relationship between those datasets (LCIs and LCIA methods) through an angular distance. RIs highlight LCIA methods that measure issues for which the LCI can be particularly harmful. A high RI indicates a close proximity between a LCI and a LCIA method, and highlights a better representation of the elementary flows by the LCIA method. To illustrate the benefits of the proposed approach, representativeness of LCIA methods regarding four electricity mix production LCIs from the ecoinvent database are presented. RIs for 18 LCIA methods (accounting for a total of 232 impact categories) were calculated on these LCIs and the relevance of the methods are discussed. RIs prove to be a criterion for distinguishing the different LCIA methods and could thus be employed by practitioners for deeper interpretations of LCIA results. Copyright © 2017 Elsevier B.V. All rights reserved.

Regional Variability and Uncertainty of Electric Vehicle Life Cycle CO₂ Emissions across the United States.

PubMed

Tamayao, Mili-Ann M; Michalek, Jeremy J; Hendrickson, Chris; Azevedo, Inês M L

2015-07-21

We characterize regionally specific life cycle CO2 emissions per mile traveled for plug-in hybrid electric vehicles (PHEVs) and battery electric vehicles (BEVs) across the United States under alternative assumptions for regional electricity emission factors, regional boundaries, and charging schemes. We find that estimates based on marginal vs average grid emission factors differ by as much as 50% (using National Electricity Reliability Commission (NERC) regional boundaries). Use of state boundaries versus NERC region boundaries results in estimates that differ by as much as 120% for the same location (using average emission factors). We argue that consumption-based marginal emission factors are conceptually appropriate for evaluating the emissions implications of policies that increase electric vehicle sales or use in a region. We also examine generation-based marginal emission factors to assess robustness. Using these two estimates of NERC region marginal emission factors, we find the following: (1) delayed charging (i.e., starting at midnight) leads to higher emissions in most cases due largely to increased coal in the marginal generation mix at night; (2) the Chevrolet Volt has higher expected life cycle emissions than the Toyota Prius hybrid electric vehicle (the most efficient U.S. gasoline vehicle) across the U.S. in nearly all scenarios; (3) the Nissan Leaf BEV has lower life cycle emissions than the Prius in the western U.S. and in Texas, but the Prius has lower emissions in the northern Midwest regardless of assumed charging scheme and marginal emissions estimation method; (4) in other regions the lowest emitting vehicle depends on charge timing and emission factor estimation assumptions.

How can mortality increase population size? A test of two mechanistic hypotheses.

PubMed

McIntire, Kristina M; Juliano, Steven A

2018-05-03

Overcompensation occurs when added mortality increases survival to the next life-cycle stage. Overcompensation can contribute to the Hydra Effect, wherein added mortality increases equilibrium population size. One hypothesis for overcompensation is that added mortality eases density-dependence, increasing survival to adulthood ("temporal separation of mortality and density dependence"). Mortality early in the life cycle is therefore predicted to cause overcompensation, whereas mortality later in the life cycle is not. Another hypothesis for overcompensation is that threat of mortality (e.g., from predation) causes behavioral changes that reduce overexploitation of resources, allowing resource recovery, and increasing production of adults ("prudent resource exploitation"). Behaviorally active predation cues alone are therefore predicted to cause overcompensation. We tested these predictions in two experiments with larvae of two species of Aedes. As predicted, early mortality yielded greater production of adults, and of adult females, and greater estimated rate of population increase than did later mortality. Addition of water-borne predation cues usually reduced browsing on surfaces in late-stage larvae, but contrary to prediction, resulted in neither significantly greater production of adult mosquitoes nor significantly greater estimated rate of increase. Thus we have strong evidence that timing of mortality contributes to overcompensation and the Hydra effect in mosquitoes. Evidence that predation cues alone can result in overcompensation via prudent resource exploitation is lacking. We expect the overcompensation in response to early mortality will be common in organisms with complex life cycles, density dependence among juveniles, and developmental control of populations. This article is protected by copyright. All rights reserved. This article is protected by copyright. All rights reserved.

Design of the Space Station Freedom power system

NASA Technical Reports Server (NTRS)

Thomas, Ronald L.; Hallinan, George J.

1989-01-01

The design of Space Station Freedom's electric power system (EPS) is reviewed, highlighting the key design goals of performance, low cost, reliability and safety. Tradeoff study results that illustrate the competing factors responsible for many of the more important design decisions are discussed. When Freedom's EPS is compared with previous space power designs, two major differences stand out. The first is the size of the EPS, which is larger than any prior system. The second major difference between the EPS and other space power designs is the indefinite expected life of Freedom; 30 years has been used for life-cycle-cost calculations.

Life expectancy of modular Ti6Al4V hip implants: influence of stress and environment.

PubMed

Chandra, A; Ryu, J J; Karra, P; Shrotriya, P; Tvergaard, V; Gaisser, M; Weik, T

2011-11-01

Stress dependent electrochemical dissolution is identified as one of the key mechanisms governing surface degradation in fretting and crevice corrosion of biomedical implants. The present study focuses on delineating the roles of mechanical stress and chemical conditions on the life expectancy of modular hip implants. First, material removal on a stressed surface of Ti6Al4V subjected to single asperity contact is investigated experimentally to identify the influence of contact load, in-plane stress and chemical environment on mean wear rates. A range of known stress levels are applied to the specimen while its surface is mechanically stimulated in different non-reactive to oxidizing aqueous environments. Evolution of surface degradation is monitored, and its mechanism is elucidated. This phase allows estimation of Preston Constant which is later used in the analysis. Second phase of the work is semi-analytical and computational, where, based on the estimated Preston constant and other material and process parameters, the scratch propensity (consisting of magnitude of scratch depth and their frequency per unit area) due to micro-motion in modular hip implants is estimated. The third phase views these scratches as initial notches and utilizes a mixed-mode fatigue crack propagation model to estimate the critical crack length for onset of instability. The number of loading cycles needed to reach this critical crack length is then labeled as the expected life of the implant under given mechanical and chemical conditions. Implications of different material and process conditions to life expectancy of orthopedic implants are discussed. It is observed that transverse micro-motion, compared to longitudinal micro-motion, plays a far more critical role in determining the implant life. Patient body weight, as well as proximity of the joint fluid to its iso-electric point play key roles in determining wear rates and associated life expectancies of modular hip implants. Sustained aeration of joint fluid, as well as proper tolerancing of mating surfaces, along with a proper choice of material microstructure may be utilized to extend implant life. Copyright © 2011 Elsevier Ltd. All rights reserved.

Application of Different Statistical Techniques in Integrated Logistics Support of the International Space Station Alpha

NASA Technical Reports Server (NTRS)

Sepehry-Fard, F.; Coulthard, Maurice H.

1995-01-01

The process to predict the values of the maintenance time dependent variable parameters such as mean time between failures (MTBF) over time must be one that will not in turn introduce uncontrolled deviation in the results of the ILS analysis such as life cycle cost spares calculation, etc. A minor deviation in the values of the maintenance time dependent variable parameters such as MTBF over time will have a significant impact on the logistics resources demands, International Space Station availability, and maintenance support costs. It is the objective of this report to identify the magnitude of the expected enhancement in the accuracy of the results for the International Space Station reliability and maintainability data packages by providing examples. These examples partially portray the necessary information hy evaluating the impact of the said enhancements on the life cycle cost and the availability of the International Space Station.

Evaluation of rolling contact fatigue of induction heated 13Cr-2Ni-2Mo Stainless steel bar with Si3N4-ball

NASA Astrophysics Data System (ADS)

Yadoiwa, Ariyasu; Mizobe, Koshiro; Kida, Katsuyuki

2018-03-01

13Cr % martensitic stainless steels were used in various industry, because they have excellent corrosion resistance and high hardness among other stainless steels. They are also expected as a bearing material, however, the research on rolling contact fatigue (RCF) is not enough. In this study, 13Cr-2Ni-2Mo stainless steels were quenched by induction heating and their RCF lives were evaluated. A Si3N4-ball was used in order to apply higher stress (Pmax = 5.6 GPa) than our previous tests (Pmax=5.3 GPa), in a single-ball RCF testing machine. It was found that the basic life (L10) was 2.20×106 cycles and Median life (L50) was 6.04×106 cycles. In addition, Weibull modulus became higher than the previous tests.

Slocum-TREC Thermal Glider

NASA Technical Reports Server (NTRS)

Huntsberger, Terry; Jones, Jack A.; Valdez, Thomas; Stirbl, Rob

2012-01-01

JPL is now teaming with Teledyne-Webb-Research to produce the first thermal glider that uses PCM for direct buoyancy control (not electronic pumps) and to produce all other required electricity. TWR has increased electrical production total efficiency from 0.45 to 0.61. JPL performed over 6000 cycles (2.4 years) of accelerated life testing of a piston accumulator. Design, fabrication, and testing will be performed in 2012, with deployment by Rutgers University in late 2012. The proposed goal of the ocean endurance tests was 3 months, but will be extended to at last 1 year. The piston accumulator was cycled over 6,000 times in a three-month period in order to simulate continuous glider life of about 2.4 years, The life test data suggests that we might accumulate roughly 0.5 cc of gas in the oil bladders for each cycle. PCM canisters will be fabricated with a compressed aluminum foam core, 7.5% foam selected (< 42 minutes to freeze anticipated) An Axi 5345/18 3-Phase AC alternator selected for power generation, 61% energy storage efficiency A 4-Cell A123 Energy Storage Systems battery selected for energy storage, buss voltage 14.4 to 12.5 V (13.2 V nominal) Glider deployment expected in late 2012

Test Results of a Ten Cell Bipolar Nickel-hydrogen Battery

NASA Technical Reports Server (NTRS)

Cataldo, R. L.

1984-01-01

A study was initiated to design and evaluate a new design concept for nickel-hydrogen cells. This concept involved constructing a battery in a bipolar stack with cells consisting of a one plate for each nickel and hydrogen electrode. Preliminary designs at the system level of this concept promised improvements in both volumetric and gravimetric energy densities, thermal management, life extension, costs, and peak power capability over more conventional designs. Test results were most encouraging. This preprototype battery, built with less than ideal components and hardware, exceeded expectations. A total of 2000 LEO cycles at 80 percent depth of discharge were accrued. A cycle life goal of 30,000 cycles appears achievable with minor design changes. These improvements include advanced technology nickel electrodes, insulated bipolar plates and specifically designed frames to minimize shunt currents. The discharge rate capability of this design exceeds 25C. At the 10C discharge rate, 80% of the battery capacity can be withdrawn in six minutes. This data shows that the bipolar design is well suited for those applications requiring high peak power pulses.

Voltage equalization of an ultracapacitor module by cell grouping using number partitioning algorithm

NASA Astrophysics Data System (ADS)

Oyarbide, E.; Bernal, C.; Molina, P.; Jiménez, L. A.; Gálvez, R.; Martínez, A.

2016-01-01

Ultracapacitors are low voltage devices and therefore, for practical applications, they need to be used in modules of series-connected cells. Because of the inherent manufacturing tolerance of the capacitance parameter of each cell, and as the maximum voltage value cannot be exceeded, the module requires inter-cell voltage equalization. If the intended application suffers repeated fast charging/discharging cycles, active equalization circuits must be rated to full power, and thus the module becomes expensive. Previous work shows that a series connection of several sets of paralleled ultracapacitors minimizes the dispersion of equivalent capacitance values, and also the voltage differences between capacitors. Thus the overall life expectancy is improved. This paper proposes a method to distribute ultracapacitors with a number partitioning-based strategy to reduce the dispersion between equivalent submodule capacitances. Thereafter, the total amount of stored energy and/or the life expectancy of the device can be considerably improved.

Joint Direct Attack Munition (JDAM)

DTIC Science & Technology

2015-12-01

February 19, 2015 and the O&S cost are based on an ICE dated August 28, 2014 Confidence Level Confidence Level of cost estimate for current APB: 50% A...mathematically derived confidence level was not computed for this Life-Cycle Cost Estimate (LCCE). This LCCE represents the expected value, taking into...consideration relevant risks, including ordinary levels of external and unforeseen events. It aims to provide sufficient resources to execute the

Climate stability of habitable Earth-like planets

NASA Astrophysics Data System (ADS)

Menou, Kristen

2015-11-01

The carbon-silicate cycle regulates the atmospheric CO2 content of terrestrial planets on geological timescales through a balance between the rates of CO2 volcanic outgassing and planetary intake from rock weathering. It is thought to act as an efficient climatic thermostat on Earth and, by extension, on other habitable planets. If, however, the weathering rate increases with the atmospheric CO2 content, as expected on planets lacking land vascular plants, the carbon-silicate cycle feedback can become severely limited. Here we show that Earth-like planets receiving less sunlight than current Earth may no longer possess a stable warm climate but instead repeatedly cycle between unstable glaciated and deglaciated climatic states. This has implications for the search for life on exoplanets in the habitable zone of nearby stars.

How Many Batches Are Needed for Process Validation under the New FDA Guidance?

PubMed

Yang, Harry

2013-01-01

The newly updated FDA Guidance for Industry on Process Validation: General Principles and Practices ushers in a life cycle approach to process validation. While the guidance no longer considers the use of traditional three-batch validation appropriate, it does not prescribe the number of validation batches for a prospective validation protocol, nor does it provide specific methods to determine it. This potentially could leave manufacturers in a quandary. In this paper, I develop a Bayesian method to address the issue. By combining process knowledge gained from Stage 1 Process Design (PD) with expected outcomes of Stage 2 Process Performance Qualification (PPQ), the number of validation batches for PPQ is determined to provide a high level of assurance that the process will consistently produce future batches meeting quality standards. Several examples based on simulated data are presented to illustrate the use of the Bayesian method in helping manufacturers make risk-based decisions for Stage 2 PPQ, and they highlight the advantages of the method over traditional Frequentist approaches. The discussions in the paper lend support for a life cycle and risk-based approach to process validation recommended in the new FDA guidance. The newly updated FDA Guidance for Industry on Process Validation: General Principles and Practices ushers in a life cycle approach to process validation. While the guidance no longer considers the use of traditional three-batch validation appropriate, it does not prescribe the number of validation batches for a prospective validation protocol, nor does it provide specific methods to determine it. This potentially could leave manufacturers in a quandary. In this paper, I develop a Bayesian method to address the issue. By combining process knowledge gained from Stage 1 Process Design (PD) with expected outcomes of Stage 2 Process Performance Qualification (PPQ), the number of validation batches for PPQ is determined to provide a high level of assurance that the process will consistently produce future batches meeting quality standards. Several examples based on simulated data are presented to illustrate the use of the Bayesian method in helping manufacturers make risk-based decisions for Stage 2 PPQ, and THEY highlight the advantages of the method over traditional Frequentist approaches. The discussions in the paper lend support for a life cycle and risk-based approach to process validation recommended in the new FDA guidance.

Long life monopropellant hydrazine thruster evaluation for Space Station Freedom application - Test results

NASA Technical Reports Server (NTRS)

Popp, Christopher G.; Cook, Joseph C.; Ragland, Brenda L.; Pate, Leah R.

1992-01-01

In support of propulsion system thruster development activity for Space Station Freedom (SSF), NASA Johnson Space Center (JSC) conducted a hydrazine thruster technology demonstration program. The goal of this program was to identify impulse life capability of state-of-the-art long life hydrazine thrusters nominally rated for 50 pounds thrust at 300 psia supply pressure. The SSF propulsion system requirement for impulse life of this thruster class is 1.5 million pounds-seconds, corresponding to a throughput of approximately 6400 pounds of propellant. Long life thrusters were procured from The Marquardt Company, Hamilton Standard, and Rocket Research Company, Testing at JSC was completed on the thruster designs to quantify life while simulating expected thruster firing duty cycles and durations for SSF. This paper presents a review of the SSF propulsion system hydrazine thruster requirements, summaries of the three long life thruster designs procured by JSC and acceptance test results for each thruster, the JSC thruster life evaluation test program, and the results of the JSC test program.

Life cycle assessment of nuclear-based hydrogen production via thermochemical water splitting using a copper-chlorine (Cu-Cl) cycle

NASA Astrophysics Data System (ADS)

Ozbilen, Ahmet Ziyaettin

The energy carrier hydrogen is expected to solve some energy challenges. Since its oxidation does not emit greenhouse gases (GHGs), its use does not contribute to climate change, provided that it is derived from clean energy sources. Thermochemical water splitting using a Cu-Cl cycle, linked with a nuclear super-critical water cooled reactor (SCWR), which is being considered as a Generation IV nuclear reactor, is a promising option for hydrogen production. In this thesis, a comparative environmental study is reported of the three-, four- and five-step Cu-Cl thermochemical water splitting cycles with various other hydrogen production methods. The investigation uses life cycle assessment (LCA), which is an analytical tool to identify and quantify environmentally critical phases during the life cycle of a system or a product and/or to evaluate and decrease the overall environmental impact of the system or product. The LCA results for the hydrogen production processes indicate that the four-step Cu-Cl cycle has lower environmental impacts than the three- and five-step Cu-Cl cycles due to its lower thermal energy requirement. Parametric studies show that acidification potentials (APs) and global warming potentials (GWPs) for the four-step Cu-Cl cycle can be reduced from 0.0031 to 0.0028 kg SO2-eq and from 0.63 to 0.55 kg CO2-eq, respectively, if the lifetime of the system increases from 10 to 100 years. Moreover, the comparative study shows that the nuclear-based S-I and the four-step Cu-Cl cycles are the most environmentally benign hydrogen production methods in terms of AP and GWP. GWPs of the S-I and the four-step Cu-Cl cycles are 0.412 and 0.559 kg CO2-eq for reference case which has a lifetime of 60 years. Also, the corresponding APs of these cycles are 0.00241 and 0.00284 kg SO2-eq. It is also found that an increase in hydrogen plant efficiency from 0.36 to 0.65 decreases the GWP from 0.902 to 0.412 kg CO 2-eq and the AP from 0.00459 to 0.00209 kg SO2-eq for the four-step Cu-Cl cycle. Keywords: Hydrogen production, nuclear energy, Cu-Cl cycle, environmental impact, LCA.

Evaluating compression or expansion of morbidity in Canada: trends in life expectancy and health-adjusted life expectancy from 1994 to 2010

PubMed Central

Colin, Steensma; Lidia, Loukine; Bernard, C. K. Choi

2017-01-01

Introduction: The objective of this study was to investigate whether morbidity in Canada, at the national and provincial levels, is compressing or expanding by tracking trends in life expectancy (LE) and health-adjusted life expectancy (HALE) from 1994 to 2010. “Compression” refers to a decrease in the proportion of life spent in an unhealthy state over time. It happens when HALE increases faster than LE. “Expansion” refers to an increase in the proportion of life spent in an unhealthy state that happens when HALE is stable or increases more slowly than LE. Methods: We estimated LE using mortality and population data from Statistics Canada. We took health-related quality of life (i.e. morbidity) data used to calculate HALE from the National Population Health Survey (1994–1999) and the Canadian Community Health Survey (2000–2010). We built abridged life tables for seven time intervals, covering the period 1994 to 2010 and corresponding to the year of each available survey cycle, for females and males, and for each of the 10 Canadian provinces. National and provincial trends were assessed at birth, and at ages 20 years and 65 years. Results: We observed an overall average annual increase in HALE that was statistically significant in both Canadian females and males at each of the three ages assessed, with the exception of females at birth. At birth, HALE increased an average of 0.2% (p = .08) and 0.3% (p < .001) annually for females and males respectively over the 1994 to 2010 period. At the national level for all three age groups, we observed a statistically nonsignificant average annual increase in the proportion of life spent in an unhealthy state, with the exception of men at age 65, who experienced a non-significant decrease. At the provincial level at birth, we observed a significant increase in proportion of life spent in an unhealthy state for Newfoundland and Labrador (NL) and Prince Edward Island (PEI). Conclusion: Our study did not detect a clear overall trend in compression or expansion of morbidity from 1994 to 2010 at the national level in Canada. However, our results suggested an expansion of morbidity in NL and PEI. Our study indicates the importance of continued tracking of the secular trends of life expectancy and HALE in Canada in order to verify the presence of compression or expansion of morbidity. Further study should be undertaken to understand what is driving the observed expansion of morbidity in NL and in PEI. PMID:28273034

Exceptional effect of glassy lithium fluorophosphate on Mn-rich olivine cathode material for high-performance Li ion batteries

NASA Astrophysics Data System (ADS)

Kim, Jongsoon; Kim, Hyungsub; Myung, Seung-Taek; Yoo, Jung-Keun; Lee, Seongsu

2018-01-01

Mn-rich olivine LiFe0.3Mn0.7PO4 is homogenously encapsulated by an ∼3-nm-thick conductive nanolayer composed of the glassy lithium fluorophosphate through simple non-stoichiometric synthesis using additives of small amounts of LiF and a phosphorus source. The coating of the glassy lithium fluorophosphate nanolayer is clearly verified using transmission electron microscopy and X-ray photoelectron spectroscopy. It enables significant decrease in charge transfer resistance of LiFe0.3Mn0.7PO4 and improvement of its sluggish Li diffusion. At a rate of 10C, the LiFe0.3Mn0.7PO4 encapsulated by conductive glassy lithium fluorophosphate (LiFe0.3Mn0.7PO4-GLFP) electrode delivers a capacity of ∼130 mAh g-1, which is ∼77% of its theoretical capacity (∼170 mAh g-1) and ∼1.5 times higher than that of the pristine counterpart at 10C. Furthermore, LiFe0.3Mn0.7PO4-GLFP achieves outstanding cycle stability (∼75% retention of its initial capacity over 500 cycles at 1C). The proposed olivine LiFe0.3Mn0.7PO4-GLFP battery is thus expected to be a promising candidate for large-scale energy storage applications.

Evolution and regulation of complex life cycles: a brown algal perspective.

PubMed

Cock, J Mark; Godfroy, Olivier; Macaisne, Nicolas; Peters, Akira F; Coelho, Susana M

2014-02-01

The life cycle of an organism is one of its fundamental features, influencing many aspects of its biology. The brown algae exhibit a diverse range of life cycles indicating that transitions between life cycle types may have been key adaptive events in the evolution of this group. Life cycle mutants, identified in the model organism Ectocarpus, are providing information about how life cycle progression is regulated at the molecular level in brown algae. We explore some of the implications of the phenotypes of the life cycle mutants described to date and draw comparisons with recent insights into life cycle regulation in the green lineage. Given the importance of coordinating growth and development with life cycle progression, we suggest that the co-option of ancient life cycle regulators to control key developmental events may be a common feature in diverse groups of multicellular eukaryotes. Copyright © 2013 Elsevier Ltd. All rights reserved.

Role of intermediate phase for stable cycling of Na7V4(P2O7)4PO4 in sodium ion battery

PubMed Central

Lim, Soo Yeon; Kim, Heejin; Chung, Jaehoon; Lee, Ji Hoon; Kim, Byung Gon; Choi, Jeon-Jin; Chung, Kyung Yoon; Cho, Woosuk; Kim, Seung-Joo; Goddard, William A.; Jung, Yousung; Choi, Jang Wook

2014-01-01

Sodium ion batteries offer promising opportunities in emerging utility grid applications because of the low cost of raw materials, yet low energy density and limited cycle life remain critical drawbacks in their electrochemical operations. Herein, we report a vanadium-based ortho-diphosphate, Na7V4(P2O7)4PO4, or VODP, that significantly reduces all these drawbacks. Indeed, VODP exhibits single-valued voltage plateaus at 3.88 V vs. Na/Na+ while retaining substantial capacity (>78%) over 1,000 cycles. Electronic structure calculations reveal that the remarkable single plateau and cycle life originate from an intermediate phase (a very shallow voltage step) that is similar both in the energy level and lattice parameters to those of fully intercalated and deintercalated states. We propose a theoretical scheme in which the reaction barrier that arises from lattice mismatches can be evaluated by using a simple energetic consideration, suggesting that the presence of intermediate phases is beneficial for cell kinetics by buffering the differences in lattice parameters between initial and final phases. We expect these insights into the role of intermediate phases found for VODP hold in general and thus provide a helpful guideline in the further understanding and design of battery materials. PMID:24379365

Role of intermediate phase for stable cycling of Na7V4(P2O7)4PO4 in sodium ion battery.

PubMed

Lim, Soo Yeon; Kim, Heejin; Chung, Jaehoon; Lee, Ji Hoon; Kim, Byung Gon; Choi, Jeon-Jin; Chung, Kyung Yoon; Cho, Woosuk; Kim, Seung-Joo; Goddard, William A; Jung, Yousung; Choi, Jang Wook

2014-01-14

Sodium ion batteries offer promising opportunities in emerging utility grid applications because of the low cost of raw materials, yet low energy density and limited cycle life remain critical drawbacks in their electrochemical operations. Herein, we report a vanadium-based ortho-diphosphate, Na7V4(P2O7)4PO4, or VODP, that significantly reduces all these drawbacks. Indeed, VODP exhibits single-valued voltage plateaus at 3.88 V vs. Na/Na(+) while retaining substantial capacity (>78%) over 1,000 cycles. Electronic structure calculations reveal that the remarkable single plateau and cycle life originate from an intermediate phase (a very shallow voltage step) that is similar both in the energy level and lattice parameters to those of fully intercalated and deintercalated states. We propose a theoretical scheme in which the reaction barrier that arises from lattice mismatches can be evaluated by using a simple energetic consideration, suggesting that the presence of intermediate phases is beneficial for cell kinetics by buffering the differences in lattice parameters between initial and final phases. We expect these insights into the role of intermediate phases found for VODP hold in general and thus provide a helpful guideline in the further understanding and design of battery materials.

Rechargeable lithium battery technology - A survey

NASA Technical Reports Server (NTRS)

Halpert, Gerald; Surampudi, Subbarao

1990-01-01

The technology of the rechargeable lithium battery is discussed with special attention given to the types of rechargeable lithium cells and to their expected performance and advantages. Consideration is also given to the organic-electrolyte and polymeric-electrolyte cells and to molten salt lithium cells, as well as to technical issues, such as the cycle life, charge control, rate capability, cell size, and safety. The role of the rechargeable lithium cell in future NASA applications is discussed.

Earth's oxygen cycle and the evolution of animal life.

PubMed

Reinhard, Christopher T; Planavsky, Noah J; Olson, Stephanie L; Lyons, Timothy W; Erwin, Douglas H

2016-08-09

The emergence and expansion of complex eukaryotic life on Earth is linked at a basic level to the secular evolution of surface oxygen levels. However, the role that planetary redox evolution has played in controlling the timing of metazoan (animal) emergence and diversification, if any, has been intensely debated. Discussion has gravitated toward threshold levels of environmental free oxygen (O2) necessary for early evolving animals to survive under controlled conditions. However, defining such thresholds in practice is not straightforward, and environmental O2 levels can potentially constrain animal life in ways distinct from threshold O2 tolerance. Herein, we quantitatively explore one aspect of the evolutionary coupling between animal life and Earth's oxygen cycle-the influence of spatial and temporal variability in surface ocean O2 levels on the ecology of early metazoan organisms. Through the application of a series of quantitative biogeochemical models, we find that large spatiotemporal variations in surface ocean O2 levels and pervasive benthic anoxia are expected in a world with much lower atmospheric pO2 than at present, resulting in severe ecological constraints and a challenging evolutionary landscape for early metazoan life. We argue that these effects, when considered in the light of synergistic interactions with other environmental parameters and variable O2 demand throughout an organism's life history, would have resulted in long-term evolutionary and ecological inhibition of animal life on Earth for much of Middle Proterozoic time (∼1.8-0.8 billion years ago).

Waste-to-energy: A review of life cycle assessment and its extension methods.

PubMed

Zhou, Zhaozhi; Tang, Yuanjun; Chi, Yong; Ni, Mingjiang; Buekens, Alfons

2018-01-01

This article proposes a comprehensive review of evaluation tools based on life cycle thinking, as applied to waste-to-energy. Habitually, life cycle assessment is adopted to assess environmental burdens associated with waste-to-energy initiatives. Based on this framework, several extension methods have been developed to focus on specific aspects: Exergetic life cycle assessment for reducing resource depletion, life cycle costing for evaluating its economic burden, and social life cycle assessment for recording its social impacts. Additionally, the environment-energy-economy model integrates both life cycle assessment and life cycle costing methods and judges simultaneously these three features for sustainable waste-to-energy conversion. Life cycle assessment is sufficiently developed on waste-to-energy with concrete data inventory and sensitivity analysis, although the data and model uncertainty are unavoidable. Compared with life cycle assessment, only a few evaluations are conducted to waste-to-energy techniques by using extension methods and its methodology and application need to be further developed. Finally, this article succinctly summarises some recommendations for further research.

Life cycle environmental impacts of vacuum cleaners and the effects of European regulation.

PubMed

Gallego-Schmid, Alejandro; Mendoza, Joan Manuel F; Jeswani, Harish Kumar; Azapagic, Adisa

2016-07-15

Energy efficiency of vacuum cleaners has been declining over the past decades while at the same time their number in Europe has been increasing. The European Commission has recently adopted an eco-design regulation to improve the environmental performance of vacuum cleaners. In addition to the existing directive on waste electrical and electronic equipment (WEEE), the regulation could potentially have significant effects on the environmental performance of vacuum cleaners. However, the scale of the effects is currently unknown, beyond scant information on greenhouse gas emissions. Thus, this paper considers for the first time life cycle environmental impacts of vacuum cleaners and the effects of the implementation of these regulations at the European level. The effects of electricity decarbonisation, product lifetime and end-of-life disposal options are also considered. The results suggest that the implementation of the eco-design regulation alone will reduce significantly the impacts from vacuum cleaners (37%-44%) by 2020 compared with current situation. If business as usual continued and the regulation was not implemented, the impacts would be 82%-109% higher by 2020 compared to the impacts with the implementation of the regulation. Improvements associated with the implementation of the WEEE directive will be much smaller (<1% in 2020). However, if the WEEE directive did not exist, then the impacts would be 2%-21% higher by 2020 relative to the impacts with the implementation of the directive. Further improvements in most impacts (6%-20%) could be achieved by decarbonising the electricity mix. Therefore, energy efficiency measures must be accompanied by appropriate actions to reduce the environmental impacts of electricity generation; otherwise, the benefits of improved energy efficiency could be limited. Moreover, because of expected lower life expectancy of vacuum cleaners and limited availability of some raw materials, the eco-design regulation should be broadened to reduce the impacts from raw materials, production and end-of-life management. Copyright © 2016 The Authors. Published by Elsevier B.V. All rights reserved.

An Update on the Lithium-Ion Cell Low-Earth-Orbit Verification Test Program

NASA Technical Reports Server (NTRS)

Reid, Concha M.; Manzo, Michelle A.; Miller, Thomas B.; McKissock, Barbara I.; Bennett, William

2007-01-01

A Lithium-Ion Cell Low-Earth-Orbit Verification Test Program is being conducted by NASA Glenn Research Center to assess the performance of lithium-ion (Li-ion) cells over a wide range of low-Earth-orbit (LEO) conditions. The data generated will be used to build an empirical model for Li-ion batteries. The goal of the modeling will be to develop a tool to predict the performance and cycle life of Li-ion batteries operating at a specified set of mission conditions. Using this tool, mission planners will be able to design operation points of the battery system while factoring in mission requirements and the expected life and performance of the batteries. Test conditions for the program were selected via a statistical design of experiments to span a range of feasible operational conditions for LEO aerospace applications. The variables under evaluation are temperature, depth-of-discharge (DOD), and end-of-charge voltage (EOCV). The baseline matrix was formed by generating combinations from a set of three values for each variable. Temperature values are 10 C, 20 C and 30 C. Depth-of-discharge values are 20%, 30% and 40%. EOCV values are 3.85 V, 3.95 V, and 4.05 V. Test conditions for individual cells may vary slightly from the baseline test matrix depending upon the cell manufacturer s recommended operating conditions. Cells from each vendor are being evaluated at each of ten sets of test conditions. Cells from four cell manufacturers are undergoing life cycle tests. Life cycling on the first sets of cells began in September 2004. These cells consist of Saft 40 ampere-hour (Ah) cells and Lith ion 30 Ah cells. These cells have achieved over 10,000 cycles each, equivalent to about 20 months in LEO. In the past year, the test program has expanded to include the evaluation of Mine Safety Appliances (MSA) 50 Ah cells and ABSL battery modules. The MSA cells will begin life cycling in October 2006. The ABSL battery modules consist of commercial Sony hard carbon 18650 lithium-ion cells configured in series and parallel combinations to create nominal 14.4 volt, 3 Ah packs (4s-2p). These modules have accumulated approximately 3000 cycles. Results on the performance of the cells and modules will be presented in this paper. The life prediction and performance model for Li-ion cells in LEO will be built by analyzing the data statistically and performing regression analysis. Cells are being cycled to failure so that differences in performance trends that occur at different stages in the life of the cell can be observed and accurately modeled. Cell testing is being performed at the Naval Surface Warfare Center in Crane, IN.

Capacity Management and Walkdown During LEO Cycling of Nickel-Hydrogen Cells and Batteries

NASA Technical Reports Server (NTRS)

Thaller, Lawrence H.; Zimmerman, Albert H.; To, Gloria

2001-01-01

This viewgraph presentation discusses the following topics: 1) Capacity walkdown defined and illustrated; 2) Importance of capacity walkdown: 3) Four approaches to understanding the phenomenon - Pressure Trend, Charging Curve, Electrochemical Voltage Spectroscopy, and Destructive Physical Analysis Studies; 4) Results of the interrelated studies; 5) Suggested mechanism for capacity walkdown; and 6) Charging protocols to avoid the problem. In summary: 1) capacity walkdown is a consequence of the inability to maintain a high state of charge; 2) Capacity loss is typically 35% which would be expected by the valence difference between gamma and beta nickel oxyhydroxide; 3) Cycling at -5 degrees facilitates the formation of the gamma phase; 4) Excessive overcharge can also facilitate gamma phase formation at the expense of cycle life; and 5) Conditions can now be suggested to help minimize capacity walkdown.

Habitat-based constraints on food web structure and parasite life cycles.

PubMed

Rossiter, Wayne; Sukhdeo, Michael V K

2014-04-01

Habitat is frequently implicated as a powerful determinant of community structure and species distributions, but few studies explicitly evaluate the relationship between habitat-based patterns of species' distributions and the presence or absence of trophic interactions. The complex (multi-host) life cycles of parasites are directly affected by these factors, but almost no data exist on the role of habitat in constraining parasite-host interactions at the community level. In this study the relationship(s) between species abundances, distributions and trophic interactions (including parasitism) were evaluated in the context of habitat structure (classic geomorphic designations of pools, riffles and runs) in a riverine community (Raritan River, Hunterdon County, NJ, USA). We report 121 taxa collected over a 2-year period, and compare the observed food web patterns to null model expectations. The results show that top predators are constrained to particular habitat types, and that species' distributions are biased towards pool habitats. However, our null model (which incorporates cascade model assumptions) accurately predicts the observed patterns of trophic interactions. Thus, habitat strongly dictates species distributions, and patterns of trophic interactions arise as a consequence of these distributions. Additionally, we find that hosts utilized in parasite life cycles are more overlapping in their distributions, and this pattern is more pronounced among those involved in trophic transmission. We conclude that habitat structure may be a strong predictor of parasite transmission routes, particularly within communities that occupy heterogeneous habitats.

Benchmarking wastewater treatment plants under an eco-efficiency perspective.

PubMed

Lorenzo-Toja, Yago; Vázquez-Rowe, Ian; Amores, María José; Termes-Rifé, Montserrat; Marín-Navarro, Desirée; Moreira, María Teresa; Feijoo, Gumersindo

2016-10-01

The new ISO 14045 framework is expected to slowly start shifting the definition of eco-efficiency toward a life-cycle perspective, using Life Cycle Assessment (LCA) as the environmental impact assessment method together with a system value assessment method for the economic analysis. In the present study, a set of 22 wastewater treatment plants (WWTPs) in Spain were analyzed on the basis of eco-efficiency criteria, using LCA and Life Cycle Costing (LCC) as a system value assessment method. The study is intended to be useful to decision-makers in the wastewater treatment sector, since the combined method provides an alternative scheme for analyzing the relationship between environmental impacts and costs. Two midpoint impact categories, global warming and eutrophication potential, as well as an endpoint single score indicator were used for the environmental assessment, while LCC was used for value assessment. Results demonstrated that substantial differences can be observed between different WWTPs depending on a wide range of factors such as plant configuration, plant size or even legal discharge limits. Based on these results the benchmarking of wastewater treatment facilities was performed by creating a specific classification and certification scheme. The proposed eco-label for the WWTPs rating is based on the integration of the three environmental indicators and an economic indicator calculated within the study under the eco-efficiency new framework. Copyright © 2016 Elsevier B.V. All rights reserved.

10 CFR 436.12 - Life cycle cost methodology.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 10 Energy 3 2012-01-01 2012-01-01 false Life cycle cost methodology. 436.12 Section 436.12 Energy DEPARTMENT OF ENERGY ENERGY CONSERVATION FEDERAL ENERGY MANAGEMENT AND PLANNING PROGRAMS Methodology and Procedures for Life Cycle Cost Analyses § 436.12 Life cycle cost methodology. The life cycle cost methodology...

10 CFR 436.12 - Life cycle cost methodology.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 10 Energy 3 2014-01-01 2014-01-01 false Life cycle cost methodology. 436.12 Section 436.12 Energy DEPARTMENT OF ENERGY ENERGY CONSERVATION FEDERAL ENERGY MANAGEMENT AND PLANNING PROGRAMS Methodology and Procedures for Life Cycle Cost Analyses § 436.12 Life cycle cost methodology. The life cycle cost methodology...

10 CFR 436.12 - Life cycle cost methodology.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 10 Energy 3 2013-01-01 2013-01-01 false Life cycle cost methodology. 436.12 Section 436.12 Energy DEPARTMENT OF ENERGY ENERGY CONSERVATION FEDERAL ENERGY MANAGEMENT AND PLANNING PROGRAMS Methodology and Procedures for Life Cycle Cost Analyses § 436.12 Life cycle cost methodology. The life cycle cost methodology...

10 CFR 436.12 - Life cycle cost methodology.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 10 Energy 3 2010-01-01 2010-01-01 false Life cycle cost methodology. 436.12 Section 436.12 Energy DEPARTMENT OF ENERGY ENERGY CONSERVATION FEDERAL ENERGY MANAGEMENT AND PLANNING PROGRAMS Methodology and Procedures for Life Cycle Cost Analyses § 436.12 Life cycle cost methodology. The life cycle cost methodology...

10 CFR 436.19 - Life cycle costs.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 10 Energy 3 2011-01-01 2011-01-01 false Life cycle costs. 436.19 Section 436.19 Energy DEPARTMENT OF ENERGY ENERGY CONSERVATION FEDERAL ENERGY MANAGEMENT AND PLANNING PROGRAMS Methodology and Procedures for Life Cycle Cost Analyses § 436.19 Life cycle costs. Life cycle costs are the sum of the...

10 CFR 436.12 - Life cycle cost methodology.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 10 Energy 3 2011-01-01 2011-01-01 false Life cycle cost methodology. 436.12 Section 436.12 Energy DEPARTMENT OF ENERGY ENERGY CONSERVATION FEDERAL ENERGY MANAGEMENT AND PLANNING PROGRAMS Methodology and Procedures for Life Cycle Cost Analyses § 436.12 Life cycle cost methodology. The life cycle cost methodology...

10 CFR 436.19 - Life cycle costs.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 10 Energy 3 2010-01-01 2010-01-01 false Life cycle costs. 436.19 Section 436.19 Energy DEPARTMENT OF ENERGY ENERGY CONSERVATION FEDERAL ENERGY MANAGEMENT AND PLANNING PROGRAMS Methodology and Procedures for Life Cycle Cost Analyses § 436.19 Life cycle costs. Life cycle costs are the sum of the...

The evolution of life cycle complexity in aphids: Ecological optimization or historical constraint?

PubMed

Hardy, Nate B; Peterson, Daniel A; von Dohlen, Carol D

2015-06-01

For decades, biologists have debated why many parasites have obligate multihost life cycles. Here, we use comparative phylogenetic analyses of aphids to evaluate the roles of ecological optimization and historical constraint in the evolution of life cycle complexity. If life cycle complexity is adaptive, it should be evolutionarily labile, that is, change in response to selection. We provide evidence that this is true in some aphids (aphidines), but not others (nonaphidines)-groups that differ in the intensity of their relationships with primary hosts. Next, we test specific mechanisms by which life cycle complexity could be adaptive or a constraint. We find that among aphidines there is a strong association between complex life cycles and polyphagy but only a weak correlation between life cycle complexity and reproductive mode. In contrast, among nonaphidines the relationship between life cycle complexity and host breadth is weak but the association between complex life cycles and sexual reproduction is strong. Thus, although the adaptiveness of life cycle complexity appears to be lineage specific, across aphids, life cycle evolution appears to be tightly linked with the evolution of other important natural history traits. © 2015 The Author(s). Evolution © 2015 The Society for the Study of Evolution.

The contemporary cement cycle of the United States

USGS Publications Warehouse

Kapur, A.; Van Oss, H. G.; Keoleian, G.; Kesler, S.E.; Kendall, A.

2009-01-01

A country-level stock and flow model for cement, an important construction material, was developed based on a material flow analysis framework. Using this model, the contemporary cement cycle of the United States was constructed by analyzing production, import, and export data for different stages of the cement cycle. The United States currently supplies approximately 80% of its cement consumption through domestic production and the rest is imported. The average annual net addition of in-use new cement stock over the period 2000-2004 was approximately 83 million metric tons and amounts to 2.3 tons per capita of concrete. Nonfuel carbon dioxide emissions (42 million metric tons per year) from the calcination phase of cement manufacture account for 62% of the total 68 million tons per year of cement production residues. The end-of-life cement discards are estimated to be 33 million metric tons per year, of which between 30% and 80% is recycled. A significant portion of the infrastructure in the United States is reaching the end of its useful life and will need to be replaced or rehabilitated; this could require far more cement than might be expected from economic forecasts of demand for cement. ?? 2009 Springer Japan.

High-Quality TiS2 For Li/TiS2 Cells

NASA Technical Reports Server (NTRS)

Huang, Chen-Kuo; Surampudi, Subbarao; Shen, David H.; Delgiannis, Fotios; Halpert, Gerald

1992-01-01

Modified process for synthesis of battery-grade titanium sulfide (TiS2) yields substantially improved material for Li/TiS2 electrochemical cells. Includes all-vapor-phase reaction between sulfur and titanium. Product less dense and more homogeneous, consists of smaller particles of higher crystalline quality, and purer. Cells have high cathode utilization and long cycle life performance. Expected to find applications in rechargeable lithium batteries for spacecraft, military equipment, telecommunication systems, automobiles, and consumer products.

Interferometry science center

NASA Technical Reports Server (NTRS)

Sargent, A. I.

2002-01-01

The Interferometry Science Center (ISC) is operated jointly by Caltech and JPL and is part of NASA's Navigator Program. The ISC has been created to facilitate the timely and successful execution of scientific investigations within the Navigator program, particularly those that rely on observations from NASA's interferometer projects. Currently, ISC is expected to provide full life cycle support for the Keck Interferometer, the Starlight mission, the Space Interferometry Mission, and the Terrestrial Planet Finder Mission. The nature and goals of ISc will be described.

The multi-disciplinary design study: A life cycle cost algorithm

NASA Technical Reports Server (NTRS)

Harding, R. R.; Pichi, F. J.

1988-01-01

The approach and results of a Life Cycle Cost (LCC) analysis of the Space Station Solar Dynamic Power Subsystem (SDPS) including gimbal pointing and power output performance are documented. The Multi-Discipline Design Tool (MDDT) computer program developed during the 1986 study has been modified to include the design, performance, and cost algorithms for the SDPS as described. As with the Space Station structural and control subsystems, the LCC of the SDPS can be computed within the MDDT program as a function of the engineering design variables. Two simple examples of MDDT's capability to evaluate cost sensitivity and design based on LCC are included. MDDT was designed to accept NASA's IMAT computer program data as input so that IMAT's detailed structural and controls design capability can be assessed with expected system LCC as computed by MDDT. No changes to IMAT were required. Detailed knowledge of IMAT is not required to perform the LCC analyses as the interface with IMAT is noninteractive.

Advanced high-temperature batteries

NASA Technical Reports Server (NTRS)

Nelson, Paul A.

1989-01-01

The promise of very high specific energy and power was not yet achieved for practical battery systems. Some recent approaches are discussed for new approaches to achieving high performance for lithium/DeS2 cells and sodium/metal chloride cells. The main problems for the development of successful LiAl/FeS2 cells were the instability of the FeS2 electrode, which has resulted in rapidly declining capacity, the lack of an internal mechanism for accommodating overcharge of a cell, thus requiring the use of external charge control on each individual cell, and the lack of a suitable current collector for the positive electrode other than expensive molybdenum sheet material. Much progress was made in solving the first two problems. Reduction of the operating temperatures to 400 C by a change in electrolyte composition has increased the expected life to 1000 cycles. Also, a lithium shuttle mechanism was demonstrated for selected electrode compositions that permits sufficient overcharge tolerance to adjust for the normally expected cell-to-cell deviation in coulombic efficiency. Sodium/sulfur batteries and sodium/metal chloride batteries have demonstrated good reliability and long cycle life. For applications where very high power is desired, new electrolyte coinfigurations would be required. Design work was carried out for the sodium/metal chloride battery that demonstrates the feasibility of achieving high specific energy and high power for large battery cells having thin-walled high-surface area electrolytes.

Lithium Ion Testing at NSWC Crane in Support of NASA Goddard Space Flight Center

NASA Technical Reports Server (NTRS)

Brown, Harry; Jung, David; Lee, Leonine

2010-01-01

This viewgraph presentation reviews Lithium Ion Cell testing at the Naval Surface Warfare Center in Crane, India. The contents include: 1) Quallion 15 Ahr Lithium-Ion Cells, LEO Life Cycle Test; 2) Lithion 50 Ahr Lithium-Ion Cells, LEO Life Cycle Test; 3) ABSL 5 Ahr Lithium-Ion Battery, LRO-LLO Life Cycle Test, SDO-GEO Life Cycle Test; and 4) A123 40 Ahr Lithium-Ion Battery, GPM Life Cycle Test, MMS Life Cycle Test.

Assessment of Solder Joint Fatigue Life Under Realistic Service Conditions

NASA Astrophysics Data System (ADS)

Hamasha, Sa'd.; Jaradat, Younis; Qasaimeh, Awni; Obaidat, Mazin; Borgesen, Peter

2014-12-01

The behavior of lead-free solder alloys under complex loading scenarios is still not well understood. Common damage accumulation rules fail to account for strong effects of variations in cycling amplitude, and random vibration test results cannot be interpreted in terms of performance under realistic service conditions. This is a result of the effects of cycling parameters on materials properties. These effects are not yet fully understood or quantitatively predictable, preventing modeling based on parameters such as strain, work, or entropy. Depending on the actual spectrum of amplitudes, Miner's rule of linear damage accumulation has been shown to overestimate life by more than an order of magnitude, and greater errors are predicted for other combinations. Consequences may be particularly critical for so-called environmental stress screening. Damage accumulation has, however, been shown to scale with the inelastic work done, even if amplitudes vary. This and the observation of effects of loading history on subsequent work per cycle provide for a modified damage accumulation rule which allows for the prediction of life. Individual joints of four different Sn-Ag-Cu-based solder alloys (SAC305, SAC105, SAC-Ni, and SACXplus) were cycled in shear at room temperature, alternating between two different amplitudes while monitoring the evolution of the effective stiffness and work per cycle. This helped elucidate general trends and behaviors that are expected to occur in vibrations of microelectronics assemblies. Deviations from Miner's rule varied systematically with the combination of amplitudes, the sequences of cycles, and the strain rates in each. The severity of deviations also varied systematically with Ag content in the solder, but major effects were observed for all the alloys. A systematic analysis was conducted to assess whether scenarios might exist in which the more fatigue-resistant high-Ag alloys would fail sooner than the lower-Ag ones.

Concepts associated with a unified life cycle analysis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Whelan, Gene; Peffers, Melissa S.; Tolle, Duane A.

There is a risk associated with most things in the world, and all things have a life cycle unto themselves, even brownfields. Many components can be described by a''cycle of life.'' For example, five such components are life-form, chemical, process, activity, and idea, although many more may exist. Brownfields may touch upon several of these life cycles. Each life cycle can be represented as independent software; therefore, a software technology structure is being formulated to allow for the seamless linkage of software products, representing various life-cycle aspects. Because classes of these life cycles tend to be independent of each other,more » the current research programs and efforts do not have to be revamped; therefore, this unified life-cycle paradigm builds upon current technology and is backward compatible while embracing future technology. Only when two of these life cycles coincide and one impacts the other is there connectivity and a transfer of information at the interface. The current framework approaches (e.g., FRAMES, 3MRA, etc.) have a design that is amenable to capturing (1) many of these underlying philosophical concepts to assure backward compatibility of diverse independent assessment frameworks and (2) linkage communication to help transfer the needed information at the points of intersection. The key effort will be to identify (1) linkage points (i.e., portals) between life cycles, (2) the type and form of data passing between life cycles, and (3) conditions when life cycles interact and communicate. This paper discusses design aspects associated with a unified life-cycle analysis, which can support not only brownfields but also other types of assessments.« less

NREL: U.S. Life Cycle Inventory Database Home Page

Science.gov Websites

U.S. Life-Cycle Inventory Database Buildings Research Photo of a green field with an ocean in the background. U.S. Life Cycle Inventory Database NREL and its partners created the U.S. Life Cycle Inventory (LCI) Database to help life cycle assessment (LCA) practitioners answer questions about environmental

NREL: U.S. Life Cycle Inventory Database - User Poll

Science.gov Websites

User Poll In preparation for the 2009 U.S. Life Cycle Inventory (LCI) Data Stakeholder meeting, the interested in life cycle analysis. The results from that poll and information gathered from the stakeholders polling data and feedback from life cycle analysis supporters helped develop the U.S. Life Cycle Inventory

High temperature, low-cycle fatigue of copper-base alloys in argon. Part 2: Zirconium-copper at 482, 538 and 593 C

NASA Technical Reports Server (NTRS)

Conway, J. B.; Stentz, R. H.; Berling, J. T.

1973-01-01

Zirconium-copper (1/2 hard) was tested in argon over the temperature range from 482 to 593 C in an evaluation of short-term tensile and low-cycle fatigue behavior. The effect of strain rate on the tensile properties was evaluated at 538 C and in general it was found that the yield and ultimate strengths increased as the strain rate was increased from 0.0004 to 0.01/sec. Ductility was essentially insensitive to strain rate in the case of the zirconium-copper alloy. Strain-rate and hold-time effects on the low cycle fatigue behavior of zirconium-copper were evaluated in argon at 538 C. These effects were as expected in that decreased fatigue life was noted as the strain rate decreased and when hold times were introduced into the tension portion of the strain-cycle. Hold times in compression were much less detrimental than hold times in tension.

10 CFR 436.19 - Life cycle costs.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 10 Energy 3 2014-01-01 2014-01-01 false Life cycle costs. 436.19 Section 436.19 Energy DEPARTMENT... Procedures for Life Cycle Cost Analyses § 436.19 Life cycle costs. Life cycle costs are the sum of the... (d) Energy and/or water costs. [55 FR 48220, Nov. 20, 1990, as amended at 61 FR 32651, June 25, 1996] ...

10 CFR 436.19 - Life cycle costs.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 10 Energy 3 2013-01-01 2013-01-01 false Life cycle costs. 436.19 Section 436.19 Energy DEPARTMENT... Procedures for Life Cycle Cost Analyses § 436.19 Life cycle costs. Life cycle costs are the sum of the... (d) Energy and/or water costs. [55 FR 48220, Nov. 20, 1990, as amended at 61 FR 32651, June 25, 1996] ...

10 CFR 436.19 - Life cycle costs.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 10 Energy 3 2012-01-01 2012-01-01 false Life cycle costs. 436.19 Section 436.19 Energy DEPARTMENT... Procedures for Life Cycle Cost Analyses § 436.19 Life cycle costs. Life cycle costs are the sum of the... (d) Energy and/or water costs. [55 FR 48220, Nov. 20, 1990, as amended at 61 FR 32651, June 25, 1996] ...

Life-cycle assessment of diesel, natural gas and hydrogen fuel cell bus transportation systems

NASA Astrophysics Data System (ADS)

Ally, Jamie; Pryor, Trevor

The Sustainable Transport Energy Programme (STEP) is an initiative of the Government of Western Australia, to explore hydrogen fuel cell technology as an alternative to the existing diesel and natural gas public transit infrastructure in Perth. This project includes three buses manufactured by DaimlerChrysler with Ballard fuel cell power sources operating in regular service alongside the existing natural gas and diesel bus fleets. The life-cycle assessment (LCA) of the fuel cell bus trial in Perth determines the overall environmental footprint and energy demand by studying all phases of the complete transportation system, including the hydrogen infrastructure, bus manufacturing, operation, and end-of-life disposal. The LCAs of the existing diesel and natural gas transportation systems are developed in parallel. The findings show that the trial is competitive with the diesel and natural gas bus systems in terms of global warming potential and eutrophication. Emissions that contribute to acidification and photochemical ozone are greater for the fuel cell buses. Scenario analysis quantifies the improvements that can be expected in future generations of fuel cell vehicles and shows that a reduction of greater than 50% is achievable in the greenhouse gas, photochemical ozone creation and primary energy demand impact categories.

10 CFR 435.8 - Life-cycle costing.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 10 Energy 3 2013-01-01 2013-01-01 false Life-cycle costing. 435.8 Section 435.8 Energy DEPARTMENT...-cycle costing. Each Federal agency shall determine life-cycle cost-effectiveness by using the procedures..., including lower life-cycle costs, positive net savings, savings-to-investment ratio that is estimated to be...

10 CFR 435.8 - Life-cycle costing.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 10 Energy 3 2014-01-01 2014-01-01 false Life-cycle costing. 435.8 Section 435.8 Energy DEPARTMENT...-cycle costing. Each Federal agency shall determine life-cycle cost-effectiveness by using the procedures..., including lower life-cycle costs, positive net savings, savings-to-investment ratio that is estimated to be...

10 CFR 435.8 - Life-cycle costing.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 10 Energy 3 2012-01-01 2012-01-01 false Life-cycle costing. 435.8 Section 435.8 Energy DEPARTMENT...-cycle costing. Each Federal agency shall determine life-cycle cost-effectiveness by using the procedures..., including lower life-cycle costs, positive net savings, savings-to-investment ratio that is estimated to be...

A comparison of production system life cycle models

NASA Astrophysics Data System (ADS)

Attri, Rajesh; Grover, Sandeep

2012-09-01

Companies today need to keep up with the rapidly changing market conditions to stay competitive. The main issues in this paper are related to a company's market and its competitors. The prediction of market behavior is helpful for a manufacturing enterprise to build efficient production systems. However, these predictions are usually not reliable. A production system is required to adapt to changing markets, but such requirement entails higher cost. Hence, analyzing different life cycle models of the production system is necessary. In this paper, different life cycle models of the production system are compared to evaluate the distinctive features and the limitations of each model. Furthermore, the difference between product life cycle and production life cycle is summarized, and the effect of product life cycle on production life cycle is explained. Finally, a production system life cycle model, along with key activities to be performed in each stage, is proposed specifically for the manufacturing sector.

A life cycle database for parasitic acanthocephalans, cestodes, and nematodes

USGS Publications Warehouse

Benesh, Daniel P.; Lafferty, Kevin D.; Kuris, Armand

2017-01-01

Parasitologists have worked out many complex life cycles over the last ~150 years, yet there have been few efforts to synthesize this information to facilitate comparisons among taxa. Most existing host-parasite databases focus on particular host taxa, do not distinguish final from intermediate hosts, and lack parasite life-history information. We summarized the known life cycles of trophically transmitted parasitic acanthocephalans, cestodes, and nematodes. For 973 parasite species, we gathered information from the literature on the hosts infected at each stage of the parasite life cycle (8510 host-parasite species associations), what parasite stage is in each host, and whether parasites need to infect certain hosts to complete the life cycle. We also collected life-history data for these parasites at each life cycle stage, including 2313 development time measurements and 7660 body size measurements. The result is the most comprehensive data summary available for these parasite taxa. In addition to identifying gaps in our knowledge of parasite life cycles, these data can be used to test hypotheses about life cycle evolution, host specificity, parasite life-history strategies, and the roles of parasites in food webs.

Impact of Life-Cycle Stage and Gender on the Ability to Balance Work and Family Responsibilities.

ERIC Educational Resources Information Center

Higgins, Christopher; And Others

1994-01-01

Examined impact of gender and life-cycle stage on three components of work-family conflict using sample of 3,616 respondents. For men, levels of work-family conflict were moderately lower in each successive life-cycle stage. For women, levels were similar in two early life-cycle stages but were significantly lower in later life-cycle stage.…

Alisse : Advanced life support system evaluator

NASA Astrophysics Data System (ADS)

Brunet, Jean; Gerbi, Olivier; André, Philippe; Davin, Elisabeth; Avezuela Rodriguez, Raul; Carbonero, Fernando; Soumalainen, Emilia; Lasseur, Christophe

Long duration missions, such as the establishment of permanent bases on the lunar surface or the travel to Mars, require such an amount of life support consumables (e.g. food, water and oxygen) that direct supply or re-supply from Earth is not an option anymore. Regenerative Life Support Systems are therefore necessary to sustain long-term manned space mission to increase recycling rates and so reduce the launched mass. The architecture of an Environmental Controlled Life Support System widely depends on the mission scenario. Even for a given mission scenario, different architectures could be envisaged which need to be evaluated and compared with appropriate tools. As these evaluation and comparison, based on the single criterion of Equivalent System Mass, was not considered com-prehensive enough, ESA is developing a multi-criteria evaluation tool: ALISSE (Advanced Life Support System Evaluator). The main objective of ALISSE, and of the work presented here, is the definition and implemen-tation of a metrics system, addressing the complexity of any ECLSS along its Life Cycle phases. A multi-dimensional and multi-criteria (i.e. mass, energy, efficiency, risk to human, reliability, crew time, sustainability, life cycle cost) approach is proposed through the development of a computing support platform. Each criterion being interrelated with the others, a model based system approach is used. ALISSE is expected to provide significant inputs to the ESA Concurrent Design Facility and, as a consequence, to be a highly valuable tool for decision process linked to any manned space mission. Full contact detail for the contact author : Jean Brunet Sherpa Engineering General Manager Phone : 0033(0)608097480 j.brunet@sherpa-eng.com

comment="please make the changes marked up in the attached pdf"Sex-Dependent Effects of Caloric Restriction on the Ageing of an Ambush Feeding Copepod.

PubMed

Saiz, Enric; Calbet, Albert; Griffell, Kaiene

2017-10-04

Planktonic copepods are a very successful group in marine pelagic environments, with a key role in biogeochemical cycles. Among them, the genus Oithona is one of the more abundant and ubiquitous. We report here on the effects of caloric (food) restriction on the ageing patterns of the copepod Oithona davisae. The response of O. davisae to caloric restriction was sex dependent: under food limitation, females have lower age-specific mortality rates and longer lifespans and reproductive periods; male mortality rates and life expectancy were not affected. Males are more active swimmers than females, and given their higher energetic demands presumably generate reactive oxygen species at higher rates. That was confirmed by starvation experiments, which showed that O. davisae males burn through body reserves much faster, resulting in shorter life expectancy. Compared with common, coastal calanoid copepods, the effects of caloric restriction on O. davisae appeared less prominent. We think this difference in the magnitude of the responses is a consequence of the distinct life-history traits associated with the genus Oithona (ambush feeder, egg-carrier), with much lower overall levels of metabolism and reproductive effort.

[To bleed or not--a new dogma or a real choice in contraception?].

PubMed

Renteria, Saira-Christine

2008-10-22

Let's talk about it Suppression of menstruation, by extending the duration of contraceptives containing estro-progestins (oral contraception, patch or vaginal ring) to long cycles, is a new approach in the field of contraception. These extended cycles aim at obtaining prolonged amenorrhea, interrupted periodically by a free interval of 7 days without hormone intake and thus causing breakthrough bleeding. Pathologies, which are supposed to get some benefit from the suppression of menstruation and of hormone level variations related to ovarian activity, are widely recognized as an indication. Some interest is also coming up for so called life style indications. Treatment issues, advantages and disadvantages are examined in the light of women's expectations and right to access to informed consent and independent choice.

The theory of modulated hormone therapy for the treatment of breast cancer in pre- and post-menopausal women

NASA Astrophysics Data System (ADS)

Wiley, Teresa S.; Haraldsen, Jason T.

2012-03-01

We present a theory that questions the standard of care for pre- and post-menopausal women with breast cancer. Through the use of modulated hormones to mimic the natural multiphasic fluctuations of estrogen and progesterone cycles of healthy young women, it can be expected that patients will not only exhibit increased quality of life such as better sleep, well-being, and libido, but also memory improvement and less joint pain. Additionally, this regimen may engage genetic pathways that protect women in youth from breast cancers. We present a mathematical basis for the coupling of the hormone cycles through the use of Gaussian curves that provides the foundation of a new format of hormone replacement in women.

Dispersed storage and generation case studies

NASA Technical Reports Server (NTRS)

Bahrami, K.; Stallkamp, J. A.; Walton, A.

1980-01-01

Three installations utilizing separate dispersed storage and generation (DSG) technologies were investigated. Each of the systems is described in costs and control. Selected institutional and environmental issues are discussed, including life cycle costs. No unresolved technical, environmental, or institutional problems were encountered in the installations. The wind and solar photovoltaic DSG were installed for test purposes, and appear to be presently uneconomical. However, a number of factors are decreasing the cost of DSG relative to conventional alternatives, and an increased DSG penetration level may be expected in the future.

Application of Design of Experiments and Surrogate Modeling within the NASA Advanced Concepts Office, Earth-to-Orbit Design Process

NASA Technical Reports Server (NTRS)

Zwack, Matthew R.; Dees, Patrick D.; Holt, James B.

2016-01-01

Decisions made during early conceptual design can have a profound impact on life-cycle cost (LCC). Widely accepted that nearly 80% of LCC is committed. Decisions made during early design must be well informed. Advanced Concepts Office (ACO) at Marshall Space Flight Center aids in decision making for launch vehicles. Provides rapid turnaround pre-phase A and phase A studies. Provides customer with preliminary vehicle sizing information, vehicle feasibility, and expected performance.

The Effect of Structural Quality on Fatigue Life in 319 Aluminum Alloy Castings

NASA Astrophysics Data System (ADS)

Özdeş, Hüseyin; Tiryakioğlu, Murat

2017-02-01

Tensile and fatigue life data for 319 aluminum alloy from seventeen datasets reported in four independent studies from the literature have been reanalyzed. Analysis of fatigue life data involved mean stress correction for different R ratios used in fatigue testing, inclusion of survival (runout) data along with failure data, as well as volumetric correction for Weibull distributions for different specimen sizes used in these studies. Tensile data have been transformed into the structural quality index, Q T, which is used as a measure of the structural quality of castings. A distinct relationship has been observed between the expected fatigue life and mean quality index. Moreover, fatigue strengths at 104 and 106 cycles have been found increase with quality index, providing further evidence about the relationship observed between structural quality and fatigue performance. Empirical equations between Basquin parameters and structural quality index have been developed. The use of the comprehensive methodology to estimate fatigue life is demonstrated with an example.

Calculation of thermomechanical fatigue life based on isothermal behavior

NASA Technical Reports Server (NTRS)

Halford, Gary R.; Saltsman, James F.

1987-01-01

The isothermal and thermomechanical fatigue (TMF) crack initiation response of a hypothetical material was analyzed. Expected thermomechanical behavior was evaluated numerically based on simple, isothermal, cyclic stress-strain - time characteristics and on strainrange versus cyclic life relations that have been assigned to the material. The attempt was made to establish basic minimum requirements for the development of a physically accurate TMF life-prediction model. A worthy method must be able to deal with the simplest of conditions: that is, those for which thermal cycling, per se, introduces no damage mechanisms other than those found in isothermal behavior. Under these assumed conditions, the TMF life should be obtained uniquely from known isothermal behavior. The ramifications of making more complex assumptions will be dealt with in future studies. Although analyses are only in their early stages, considerable insight has been gained in understanding the characteristics of several existing high-temperature life-prediction methods. The present work indicates that the most viable damage parameter is based on the inelastic strainrange.

Geographic variation and evolution in the life cycle of the witch-hazel leaf gall aphid, Hormaphis hamamelidis.

PubMed

von Dohlen, C D; Gill, D E

1989-02-01

Two divergent life cycles associated with different elevations and latitudes have been documented for the witch-hazel leaf gall aphid, Hormaphis hamamelidis. At low elevation in northern Virginia, the aphid had seven distinct generations alternating between the primary host, witchhazel (Hamamelis virginiana), and a secondary host, river birch (Betula nigra). These findings confirm the original published life cycle description for the same locality. A second, abbreviated life cycle consisting of only three generations restricted to witch-hazel was discovered at high elevation (1000 m) in north central and northwestern Virginia. Aphids of both life cycles were sympatric at a middle elevation site. The life cycles and morphology suggest that the two forms are separate species. Although monoecious life cycles on primary hosts in aphids generally are thought to be ancestral to complex host-alternating ones, it is certainly possible that monoecious cycles are sometimes secondarily derived from complex cycles. By constructing a preliminary phylogeny of the described species in the tribe Hormaphidini, we propose that the abbreviated life cycle is derived from the complex one in the case of these witchhazel gall aphids. Our findings are discussed in the context of current theory regarding the evolutionary stability of complex life cycles.

32 CFR Appendix to Part 162 - Reporting Procedures

Code of Federal Regulations, 2014 CFR

2014-07-01

... generated. e. Projected Life-Cycle Savings. For each PIF project provide the estimated amount of savings the project is projected to earn over the project's economic life. f. Projected Life-Cycle Cost Avoidance. For... Projected Life-Cycle Savings. e. Total Projected Life-Cycle Cost Avoidance. 3. CSI. Each DoD Component that...

10 CFR 433.8 - Life-cycle costing.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 10 Energy 3 2014-01-01 2014-01-01 false Life-cycle costing. 433.8 Section 433.8 Energy DEPARTMENT... HIGH-RISE RESIDENTIAL BUILDINGS § 433.8 Life-cycle costing. Each Federal agency shall determine life... choose to use any of four methods, including lower life-cycle costs, positive net savings, savings-to...

19 CFR 207.27 - Short life cycle products.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 19 Customs Duties 3 2013-04-01 2013-04-01 false Short life cycle products. 207.27 Section 207.27... SUBSIDIZED EXPORTS TO THE UNITED STATES Final Determinations, Short Life Cycle Products § 207.27 Short life... short life cycle merchandise which has been the subject of two or more affirmative dumping...

10 CFR 433.8 - Life-cycle costing.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 10 Energy 3 2012-01-01 2012-01-01 false Life-cycle costing. 433.8 Section 433.8 Energy DEPARTMENT... HIGH-RISE RESIDENTIAL BUILDINGS § 433.8 Life-cycle costing. Each Federal agency shall determine life... choose to use any of four methods, including lower life-cycle costs, positive net savings, savings-to...

19 CFR 207.27 - Short life cycle products.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 19 Customs Duties 3 2014-04-01 2014-04-01 false Short life cycle products. 207.27 Section 207.27... SUBSIDIZED EXPORTS TO THE UNITED STATES Final Determinations, Short Life Cycle Products § 207.27 Short life... short life cycle merchandise which has been the subject of two or more affirmative dumping...

10 CFR 433.8 - Life-cycle costing.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 10 Energy 3 2013-01-01 2013-01-01 false Life-cycle costing. 433.8 Section 433.8 Energy DEPARTMENT... HIGH-RISE RESIDENTIAL BUILDINGS § 433.8 Life-cycle costing. Each Federal agency shall determine life... choose to use any of four methods, including lower life-cycle costs, positive net savings, savings-to...

19 CFR 207.27 - Short life cycle products.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 19 Customs Duties 3 2012-04-01 2012-04-01 false Short life cycle products. 207.27 Section 207.27... SUBSIDIZED EXPORTS TO THE UNITED STATES Final Determinations, Short Life Cycle Products § 207.27 Short life... short life cycle merchandise which has been the subject of two or more affirmative dumping...

19 CFR 207.27 - Short life cycle products.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 19 Customs Duties 3 2010-04-01 2010-04-01 false Short life cycle products. 207.27 Section 207.27... SUBSIDIZED EXPORTS TO THE UNITED STATES Final Determinations, Short Life Cycle Products § 207.27 Short life... short life cycle merchandise which has been the subject of two or more affirmative dumping...

19 CFR 207.27 - Short life cycle products.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 19 Customs Duties 3 2011-04-01 2011-04-01 false Short life cycle products. 207.27 Section 207.27... SUBSIDIZED EXPORTS TO THE UNITED STATES Final Determinations, Short Life Cycle Products § 207.27 Short life... short life cycle merchandise which has been the subject of two or more affirmative dumping...

Does It Have a Life Cycle?

ERIC Educational Resources Information Center

Keeley, Page

2010-01-01

If life continues from generation to generation, then all plants and animals must go through a life cycle, even though it may be different from organism to organism. Is this what students have "learned," or do they have their own private conceptions about life cycles? The formative assessment probe "Does It Have a Life Cycle?" reveals some…

Evaluating the environmental impacts of a nano-enhanced field emission display using life cycle assessment: a screening-level study.

PubMed

Upadhyayula, Venkata K K; Meyer, David E; Curran, Mary Ann; Gonzalez, Michael A

2014-01-21

Carbon nanotube (CNT) field emission displays (FEDs) are currently in the product development stage and are expected to be commercialized in the near future because they offer image quality and viewing angles comparable to a cathode ray tube (CRT) while using a thinner structure, similar to a liquid crystal display (LCD), and enable more efficient power consumption during use. To address concerns regarding the environmental performance of CNT-FEDs, a screening-level, cradle-to-grave life cycle assessment (LCA) was conducted based on a functional unit of 10,000 viewing hours, the viewing lifespan of a CNT-FED. Contribution analysis suggests the impacts for material acquisition and manufacturing are greater than the combined impacts for use and end-of-life. A scenario analysis of the CNT paste composition identifies the metal components used in the paste are key contributors to the impacts of the upstream stages due to the impacts associated with metal preparation. Further improvement of the manufacturing impacts is possible by considering the use of plant-based oils, such as rapeseed oil, as alternatives to organic solvents for dispersion of CNTs. Given the differences in viewing lifespan, the impacts of the CNT-FED were compared with a LCD and a CRT display to provide more insight on how to improve the CNT-FED to make it a viable product alternative. When compared with CRT technology, CNT-FEDs show better environmental performance, whereas a comparison with LCD technology indicates the environmental impacts are roughly the same. Based on the results, the enhanced viewing capabilities of CNT-FEDs will be a more viable display option if manufacturers can increase the product's expected viewing lifespan.

Long life monopropellant hydrazine thruster evaluation for Space Station Freedom application

NASA Technical Reports Server (NTRS)

Popp, Christopher G.; Henderson, John B.

1991-01-01

In support of propulsion system thruster development activity for Space Station Freedom (SSF), NASA Johnson Space Center (JSC) is conducting a hydrazine thruster technology demonstration program. The goal of this program is to identify impulse life capability of state-of-the-art long life hydrazine thrusters nominally rated for 50 pounds thrust at 300 psia supply pressure. The SSF propulsion system requirement for impulse life of this thruster class is 1.5 million pound-seconds, corresponding to a throughput of approximately 6400 pounds of propellant, with a high performance (234 pound-seconds per propellant pound). Long life thrusters were procured from Hamilton Standard, The Marquardt Company, and Rocket Research Company. Testing has initiated on the thruster designs to identify life while simulating expected thruster firing duty cycles and durations for SSF using monopropellant grade hydrazine. This paper presents a review of the SSF propulsion system and requirements as applicable to hydrazine thrusters, the three long life thruster designs procured by JSC and the resultant acceptance test data for each thruster, and the JSC test plan and facility.

Quality of Life in Elderly Cancer Patients Undergoing Chemotherapy.

PubMed

Lavdaniti, Maria; Zyga, Sofia; Vlachou, Eugenia; Sapountzi-Krepia, Despina

2017-01-01

As life expectancy increases, it is expected that 60% of all cases of cancer will be detected in elderly patients in the next two decades. Cancer treatment for older persons is complicated by a number of factors, thus negatively affecting patients' quality of life. The purpose of this study is to investigate quality of life in elderly cancer patients undergoing chemotherapy. This study was descriptive and non-experimental. It was conducted in one large hospital in a major city of Northern Greece. The sample was convenience comprising 53 elderly cancer patients undergoing cycle 3 chemotherapy. The data was collected using the Functional Assessment of Cancer Therapy scale and included questions related to demographic and clinical characteristics. The majority of participants were men (n = 27, 50.9%) who were married (n = 32, 79.5%). Their mean age was 70.07 ± 3.60. Almost half of the sample (n = 30, 56.6%) had colon cancer. There was a statistical significant difference between men and women pertaining to physical wellbeing (p = 0.004) and overall quality of life (p < 0.001). When comparing each subscale with the patients' marital status it was found that there was a statistical difference with respect to social/family wellbeing (p = 0.029), functional wellbeing (p = 0.09) and overall quality of life (p < 0.001). Moreover, the type of cancer affected overall quality of life (p < 0.001) and social/family wellbeing (p = 0.029). These findings call attention to quality of life and its related factors in elderly cancer patients. It is highly recommended to envisage measures for improving quality of life in this group of cancer patients.

Application of Life Cycle Assessment on Electronic Waste Management: A Review.

PubMed

Xue, Mianqiang; Xu, Zhenming

2017-04-01

Electronic waste is a rich source of both valuable materials and toxic substances. Management of electronic waste is one of the biggest challenges of current worldwide concern. As an effective and prevailing environmental management tool, life cycle assessment can evaluate the environmental performance of electronic waste management activities. Quite a few scientific literatures reporting life cycle assessment of electronic waste management with significant outcomes have been recently published. This paper reviewed the trends, characteristics, research gaps, and challenges of these studies providing detailed information for practitioners involved in electronic waste management. The results showed that life cycle assessment studies were most carried out in Europe, followed by Asia and North America. The research subject of the studies mainly includes monitors, waste printed circuit boards, mobile phones, computers, printers, batteries, toys, dishwashers, and light-emitting diodes. CML was the most widely used life cycle impact assessment method in life cycle assessment studies on electronic waste management, followed by EI99. Furthermore, 40% of the reviewed studies combined with other environmental tools, including life cycle cost, material flow analysis, multi-criteria decision analysis, emergy analysis, and hazard assessment which came to more comprehensive conclusions from different aspects. The research gaps and challenges including uneven distribution of life cycle assessment studies, life cycle impact assessment methods selection, comparison of the results, and uncertainty of the life cycle assessment studies were examined. Although life cycle assessment of electronic waste management facing challenges, their results will play more and more important role in electronic waste management practices.

Application of Life Cycle Assessment on Electronic Waste Management: A Review

NASA Astrophysics Data System (ADS)

Xue, Mianqiang; Xu, Zhenming

2017-04-01

Electronic waste is a rich source of both valuable materials and toxic substances. Management of electronic waste is one of the biggest challenges of current worldwide concern. As an effective and prevailing environmental management tool, life cycle assessment can evaluate the environmental performance of electronic waste management activities. Quite a few scientific literatures reporting life cycle assessment of electronic waste management with significant outcomes have been recently published. This paper reviewed the trends, characteristics, research gaps, and challenges of these studies providing detailed information for practitioners involved in electronic waste management. The results showed that life cycle assessment studies were most carried out in Europe, followed by Asia and North America. The research subject of the studies mainly includes monitors, waste printed circuit boards, mobile phones, computers, printers, batteries, toys, dishwashers, and light-emitting diodes. CML was the most widely used life cycle impact assessment method in life cycle assessment studies on electronic waste management, followed by EI99. Furthermore, 40% of the reviewed studies combined with other environmental tools, including life cycle cost, material flow analysis, multi-criteria decision analysis, emergy analysis, and hazard assessment which came to more comprehensive conclusions from different aspects. The research gaps and challenges including uneven distribution of life cycle assessment studies, life cycle impact assessment methods selection, comparison of the results, and uncertainty of the life cycle assessment studies were examined. Although life cycle assessment of electronic waste management facing challenges, their results will play more and more important role in electronic waste management practices.

Transportation life cycle assessment (LCA) synthesis : life cycle assessment learning module series.

DOT National Transportation Integrated Search

2015-03-12

The Life Cycle Assessment Learning Module Series is a set of narrated, self-advancing slideshows on : various topics related to environmental life cycle assessment (LCA). This research project produced the first 27 of such modules, which : are freely...

Modeling the influence of genetic and environmental variation on the expression of plant life cycles across landscapes.

PubMed

Burghardt, Liana T; Metcalf, C Jessica E; Wilczek, Amity M; Schmitt, Johanna; Donohue, Kathleen

2015-02-01

Organisms develop through multiple life stages that differ in environmental tolerances. The seasonal timing, or phenology, of life-stage transitions determines the environmental conditions to which each life stage is exposed and the length of time required to complete a generation. Both environmental and genetic factors contribute to phenological variation, yet predicting their combined effect on life cycles across a geographic range remains a challenge. We linked submodels of the plasticity of individual life stages to create an integrated model that predicts life-cycle phenology in complex environments. We parameterized the model for Arabidopsis thaliana and simulated life cycles in four locations. We compared multiple "genotypes" by varying two parameters associated with natural genetic variation in phenology: seed dormancy and floral repression. The model predicted variation in life cycles across locations that qualitatively matches observed natural phenology. Seed dormancy had larger effects on life-cycle length than floral repression, and results suggest that a genetic cline in dormancy maintains a life-cycle length of 1 year across the geographic range of this species. By integrating across life stages, this approach demonstrates how genetic variation in one transition can influence subsequent transitions and the geographic distribution of life cycles more generally.

Revisiting the Life Cycle of Dung Fungi, Including Sordaria fimicola.

PubMed

Newcombe, George; Campbell, Jason; Griffith, David; Baynes, Melissa; Launchbaugh, Karen; Pendleton, Rosemary

2016-01-01

Dung fungi, such as Sordaria fimicola, generally reproduce sexually with ascospores discharged from mammalian dung after passage through herbivores. Their life cycle is thought to be obligate to dung, and thus their ascospores in Quaternary sediments have been interpreted as evidence of past mammalian herbivore activity. Reports of dung fungi as endophytes would seem to challenge the view that they are obligate to dung. However, endophyte status is controversial because surface-sterilization protocols could fail to kill dung fungus ascospores stuck to the plant surface. Thus, we first tested the ability of representative isolates of three common genera of dung fungi to affect plant growth and fecundity given that significant effects on plant fitness could not result from ascospores merely stuck to the plant surface. Isolates of S. fimicola, Preussia sp., and Sporormiella sp. reduced growth and fecundity of two of three populations of Bromus tectorum, the host from which they had been isolated. In further work with S. fimicola we showed that inoculations of roots of B. tectorum led to some colonization of aboveground tissues. The same isolate of S. fimicola reproduced sexually on inoculated host plant tissues as well as in dung after passage through sheep, thus demonstrating a facultative rather than an obligate life cycle. Finally, plants inoculated with S. fimicola were not preferred by sheep; preference had been expected if the fungus were obligate to dung. Overall, these findings make us question the assumption that these fungi are obligate to dung.

Revisiting the Life Cycle of Dung Fungi, Including Sordaria fimicola

PubMed Central

Newcombe, George; Campbell, Jason; Griffith, David; Baynes, Melissa; Launchbaugh, Karen; Pendleton, Rosemary

2016-01-01

Dung fungi, such as Sordaria fimicola, generally reproduce sexually with ascospores discharged from mammalian dung after passage through herbivores. Their life cycle is thought to be obligate to dung, and thus their ascospores in Quaternary sediments have been interpreted as evidence of past mammalian herbivore activity. Reports of dung fungi as endophytes would seem to challenge the view that they are obligate to dung. However, endophyte status is controversial because surface-sterilization protocols could fail to kill dung fungus ascospores stuck to the plant surface. Thus, we first tested the ability of representative isolates of three common genera of dung fungi to affect plant growth and fecundity given that significant effects on plant fitness could not result from ascospores merely stuck to the plant surface. Isolates of S. fimicola, Preussia sp., and Sporormiella sp. reduced growth and fecundity of two of three populations of Bromus tectorum, the host from which they had been isolated. In further work with S. fimicola we showed that inoculations of roots of B. tectorum led to some colonization of aboveground tissues. The same isolate of S. fimicola reproduced sexually on inoculated host plant tissues as well as in dung after passage through sheep, thus demonstrating a facultative rather than an obligate life cycle. Finally, plants inoculated with S. fimicola were not preferred by sheep; preference had been expected if the fungus were obligate to dung. Overall, these findings make us question the assumption that these fungi are obligate to dung. PMID:26839959

Life cycle inventory of oil palm lumber production: A gate-to-gate case study

NASA Astrophysics Data System (ADS)

Shamsudin, Noor Ainna; Sahid, Ismail; Mokhtar, Anis; Muhamad, Halimah; Ahmad, Shamim

2018-04-01

Life Cycle Assessment (LCA) has been applied in the Malaysian oil palm industry since 2010. It is important to ensure that this main industry is ready to meet the demands and expectations of European market on the environmental performance of the oil palm industry. In addition, oil palm biomass, especially oil palm trunk (OPT) are abundantly available after replanting every year. In order to maximize the usage of OPT as a green product, it can be converted to palm lumber as a value-added product. Palm lumber act as a basis product from OPT before it is converted to panel product such as plywood, sandwich board and so on. However, the LCA study on palm lumber production is still scarce in Malaysia. Hence, this paper aims to perform and collect the inventory data for palm lumber production, which is known as Life Cycle Inventory (LCI). A gate-to-gate system boundary and the functional unit of 1 m3 of palm lumber produced have been used in this study. This inventory data was collected from three batches of the production cycle. The inputs are mainly the raw materials which are the OPT and the energy from diesel and electricity from the grid. Generally, each consumption of input such as energy and fossil fuel were different at each stage of palm lumber production. Kiln-drying represents a prominent stage in terms of energy consumption, which electrical use in the dryer represents 94% of total electrical grid consumption as compared to another stage of palm lumber production. By adding the inventory information especially in the downstream sector of biomass industry, hopefully it can improve the sustainability of oil palm industry in Malaysia.

LIFE CYCLE DESIGN FRAMEWORK AND DEMONSTRATION PROJECTS PROFILES OF AT&T AND ALLIED SIGNAL

EPA Science Inventory

Life cycle design seeks to minimize the environmental burden associated with a product life cycle from raw materials acquisition through manufacturing, use, and end-of-life management. ife cycle design emphasizes integrating environmental requirements into the earliest phases of ...

Inhibitory effects of (-)-epigallocatechin gallate on the life cycle of human immunodeficiency virus type 1 (HIV-1).

PubMed

Yamaguchi, Koushi; Honda, Mitsuo; Ikigai, Hajime; Hara, Yukihiko; Shimamura, Tadakatsu

2002-01-01

Epigallocatechin gallate (EGCg), the major tea catechin, is known as a potent anti-bacterial agent. In addition, anti-tumor promoting, anti-inflammatory, anti-oxidative and antiviral activities have been reported. In the present study, we investigated possible anti-human immunodeficiency virus type-1 (HIV-1) activity of EGCg and its mechanisms of action in the viral life cycle. EGCg impinges on each step of the HIV life cycle. Thus, destruction of the viral particles, viral attachment to cells, post-adsorption entry into cells, reverse transcription (RT), viral production from chronically-infected cells, and the level of expression of viral mRNA, were analyzed using T-lymphoid (H9) and monocytoid (THP-1) cell systems, and antiviral protease activity was measured using a cell-free assay. Inhibitory effects of EGCg on specific binding of the virions to the cellular surfaces and changes in the steady state viral regulation (mRNA expression) due to EGCg were not observed. However, EGCg had a destructive effect on the viral particles, and post-adsorption entry and RT in acutely infected monocytoid cells were significantly inhibited at concentrations of EGCg greater than 1 microM, and protease kinetics were suppressed at a concentration higher than 10 microM in the cell-free study. Viral production by THP-1 cells chronically-infected with HIV-1 was also inhibited in a dose-dependent manner and the inhibitory effect was enhanced by liposome modification of EGCg. As expected, increased viral mRNA production was observed in lipopolysaccharide (LPS)-activated chronically HIV-1-infected cells. This production was significantly inhibited by EGCg treatment of THP-1 cells. In contrast, production of HIV-1 viral mRNA in unstimulated or LPS-stimulated T-lymphoid cells (H9) was not inhibited by EGCg. Anti-HIV viral activity of EGCg may thus result from an interaction with several steps in the HIV-1 life cycle.

Hope, Quality of Life, and Benefit From Treatment in Women Having Chemotherapy for Platinum-Resistant/Refractory Recurrent Ovarian Cancer: The Gynecologic Cancer Intergroup Symptom Benefit Study

PubMed Central

Sjoquist, Katrin M.; Friedlander, Michael L.; O'Connell, Rachel L.; Voysey, Merryn; King, Madeleine T.; Stockler, Martin R.; Oza, Amit M.; Gillies, Kim; Martyn, Julie K.

2013-01-01

Purpose. Chemotherapy for platinum-resistant/refractory ovarian cancer is motivated by the hope of benefit. We sought to determine the relationships between: (a) trait hope, expectation of symptom benefit from chemotherapy, and anxiety and depression; (b) hope and perceived efficacy of chemotherapy; and (c) unfulfilled hope (where expectations for benefit are not fulfilled) and depression. Methods. Adult patients enrolled within stage 1 of the Gynecologic Cancer Intergroup Symptom Benefit Study were included. Patient. Reported outcomes were collected from 126 women with predominantly platinum-resistant ovarian cancer at baseline, prior to the first four treatment cycles (12–16 weeks), and four weeks after completing chemotherapy or at disease progression, whichever came first. Associations were assessed with Spearman rank correlation coefficient (r) and odds ratio. Results. Trait hope and expectation of symptom benefit from chemotherapy were weakly correlated with each other (r = 0.25). Trait hope, but not expectation of symptom benefit, was negatively correlated with anxiety (r = −0.43) and depression (r = −0.50). The smaller the discrepancy between perceived and expected symptom benefit, the less likely the patient was to have scores indicative of depression (odds ratio: 0.68; 95% confidence interval: 0.49–0.96; p = .026). Conclusion. Trait hope and expectation of symptom benefit from chemotherapy appear to be distinct and independent of the aspects of quality of life and scores for depression. Hope did not appear to affect perceived efficacy of chemotherapy in alleviating symptoms, but women whose expectation of symptom benefit from chemotherapy was not fulfilled were more likely to have scores indicative of depression. It may be preferable to encourage hope toward achievable goals rather than toward benefits from chemotherapy. PMID:24107972

Hope, quality of life, and benefit from treatment in women having chemotherapy for platinum-resistant/refractory recurrent ovarian cancer: the gynecologic cancer intergroup symptom benefit study.

PubMed

Sjoquist, Katrin M; Friedlander, Michael L; O'Connell, Rachel L; Voysey, Merryn; King, Madeleine T; Stockler, Martin R; Oza, Amit M; Gillies, Kim; Martyn, Julie K; Butow, Phyllis N

2013-01-01

Chemotherapy for platinum-resistant/refractory ovarian cancer is motivated by the hope of benefit. We sought to determine the relationships between: (a) trait hope, expectation of symptom benefit from chemotherapy, and anxiety and depression; (b) hope and perceived efficacy of chemotherapy; and (c) unfulfilled hope (where expectations for benefit are not fulfilled) and depression. Methods. Adult patients enrolled within stage 1 of the Gynecologic Cancer Intergroup Symptom Benefit Study were included. Patient. Reported outcomes were collected from 126 women with predominantly platinum-resistant ovarian cancer at baseline, prior to the first four treatment cycles (12-16 weeks), and four weeks after completing chemotherapy or at disease progression, whichever came first. Associations were assessed with Spearman rank correlation coefficient (r) and odds ratio. Results. Trait hope and expectation of symptom benefit from chemotherapy were weakly correlated with each other (r = 0.25). Trait hope, but not expectation of symptom benefit, was negatively correlated with anxiety (r = -0.43) and depression (r = -0.50). The smaller the discrepancy between perceived and expected symptom benefit, the less likely the patient was to have scores indicative of depression (odds ratio: 0.68; 95% confidence interval: 0.49-0.96; p = .026). Conclusion. Trait hope and expectation of symptom benefit from chemotherapy appear to be distinct and independent of the aspects of quality of life and scores for depression. Hope did not appear to affect perceived efficacy of chemotherapy in alleviating symptoms, but women whose expectation of symptom benefit from chemotherapy was not fulfilled were more likely to have scores indicative of depression. It may be preferable to encourage hope toward achievable goals rather than toward benefits from chemotherapy.

Life without water

NASA Technical Reports Server (NTRS)

Crowe, Lois M.; Crowe, John H.

1989-01-01

Anhydrobiosis, or life without water is commonly demonstrated by a number of plants and animals. These organisms have the capacity to loose all body water, remain dry for various periods, and then be revived by rehydration. While in the anhydrobiotic state, these organisms become highly resistant to several environmental stresses such as extremely low temperatures, elevated temperatures, ionizing radiation, and high vacuum. Since water is commonly thought to be essential for life, survival of anhydrobiotic organisms with an almost total loss of water is examined. A search of literature reveal that many anhydrobiotic organisms make large quantities of trehalose or other carbohydrates. Laboratory experiments have shown that trehalose is able to stabilize and preserve microsomes of sarcoplasmic reticulum and artificial liposomes. It was demonstrated that trehalose and other disaccharides can interact directly with phosopipid headgroups and maintain membranes in their native configuration by replacing water in the headgroup region. Recent studies show that trehalose is an effective stabilizer of proteins during drying and that it does so by direct interaction with groups on the protein. If life that is able to withstand environmental extremes has ever developed on Mars, it is expected that such life would have developed some protective compounds which can stabilize macromolecular structure in the absence of water and at cold temperatures. On Earth, that role appears to be filled by carbohydrates that can stabilize both membrane and protein stuctures during freezing and drying. By analog with terrestrial systems, such life forms might develop resistance either during some reproductive stage or at any time during adult existence. If the resistant form is a developmental stage, the life cycle of the organism must be completed with a reasonable time period relative to time when environmental conditions are favorable. This would suggest that simple organisms with a short life cycle might be most sucessful.

Life cycles of dominant mayflies (Ephemeroptera) on a torrent of the high Bolivian Andes

PubMed

Molina, Carlos I; Puliafico, Kenneth P

2016-03-01

The mayflies of the temperate and cold zones have well-synchronized life cycles, distinct cohorts, short emergence and flight periods. In contrast, aquatic insects from the tropical zones are characterized by multivoltine life cycles, “non-discernible cohorts” and extended flight periods throughout the year. This report is the first observation of life cycle patterns made of two species of mayflies on a torrent in the high elevation Bolivian Andes. The samples were taken from four sites and four periods during a hydrological season. The life cycle of each species was examined using size-class frequency analysis and a monthly modal progression model (von Bertalanffy’s model) to infer the life cycle synchrony type. These first observations showed a moderately synchronized univoltine life cycle for Andesiops peruvianus (Ulmer, 1920), whereas Meridialaris tintinnabula Pescador and Peters (1987), had an unsynchronized multivoltine life cycle. These results showed that the generalization of all aquatic insects as unsynchronized multivoltine species in the Andean region may not be entirely accurate since there is still a need to further clarify the life cycle patterns of the wide variety of aquatic insects living in this high elevation tropical environment.

From Centralized Disassembly to Life Cycle Management: Status and Progress of E-waste Treatment System in China

NASA Astrophysics Data System (ADS)

Song, Xiaolong; Yang, Jianxin; Lu, Bin; Yang, Dong

2017-01-01

China is now facing e-waste problems from both growing domestic generation and illegal imports. Many stakeholders are involved in the e-waste treatment system due to the complexity of e-waste life cycle. Beginning with the state of the e-waste treatment industry in China, this paper summarizes the latest progress in e-waste management from such aspects as the new edition of the China RoHS Directive, new Treatment List, new funding subsidy standard, and eco-design pilots. Thus, a conceptual model for life cycle management of e-waste is generalized. The operating procedure is to first identify the life cycle stages of the e-waste and extract the important life cycle information. Then, life cycle tools can be used to conduct a systematic analysis to help decide how to maximize the benefits from a series of life cycle engineering processes. Meanwhile, life cycle thinking is applied to improve the legislation relating to e-waste so as to continuously improve the sustainability of the e-waste treatment system. By providing an integrative framework, the life cycle management of e-waste should help to realize sustainable management of e-waste in developing countries.

Optimizing product life cycle processes in design phase

NASA Astrophysics Data System (ADS)

Faneye, Ola. B.; Anderl, Reiner

2002-02-01

Life cycle concepts do not only serve as basis in assisting product developers understand the dependencies between products and their life cycles, they also help in identifying potential opportunities for improvement in products. Common traditional concepts focus mainly on energy and material flow across life phases, necessitating the availability of metrics derived from a reference product. Knowledge of life cycle processes won from an existing product is directly reused in its redesign. Depending on sales volume nevertheless, the environmental impact before product optimization can be substantial. With modern information technologies today, computer-aided life cycle methodologies can be applied well before product use. On the basis of a virtual prototype, life cycle processes are analyzed and optimized, using simulation techniques. This preventive approach does not only help in minimizing (or even eliminating) environmental burdens caused by product, costs incurred due to changes in real product can also be avoided. The paper highlights the relationship between product and life cycle and presents a computer-based methodology for optimizing the product life cycle during design, as presented by SFB 392: Design for Environment - Methods and Tools at Technical University, Darmstadt.

Psychological drivers in doping: The life-cycle model of performance enhancement

PubMed Central

Petróczi, Andrea; Aidman, Eugene

2008-01-01

Background Performance enhancement (PE) is a natural and essential ingredient of competitive sport. Except for nutritional supplement contamination, accidental use of doping is highly unlikely. It requires deliberation, planning and commitment; and is influenced by a host of protective and risk factors. Hypothesis In the course of their career, athletes constantly set goals and make choices regarding the way these goals can be achieved. The cycle of choice – goal commitment – execution – feedback on goal attainment – goal evaluation/adjustment has numerous exit points, each providing an opportunity for behaviour change, which may or may not be related to the use of prohibited methods. The interplay between facilitating and inhibiting systemic and personality factors, constantly influenced by situational factors could result in an outcome vector of 'doping attitudes', which combines with subjective norms to influence intentions to choose prohibited PE methods. These influences also vary from one stage of athlete development to the next, making some athletes more vulnerable to engaging in doping practices than others, and more vulnerable at certain time periods – and not others. Testing the hypothesis Model-testing requires a series of carefully planned and coordinated studies. Correlational studies can establish relationships where the directionality is not-known or not important. Experimental studies with the manipulation of doping expectancies and risk factors can be used to demonstrate causality and evaluate potential intervention strategies. The final model can be tested via a behavioural simulation, with outcomes compared to those expected from literature precedence or used as a simulated computer game for empirical data collection. Implications A hypothesized life-cycle model of PE identifies vulnerability factors across the stages of athlete development with the view of informing the design of anti-doping assessment and intervention. The model suggests that, instead of focusing on the actual engagement in prohibited PE practices, deterrence strategies are likely to be more effective if they target the influencing factors at the appropriate stage and identify groups of athletes and their respective career stages, which pose particular risks of engagement in doping practices. This enables a more effective intervention approach by targeting specific risk factors and expectancies. PMID:18331645

LCIA framework and cross-cutting issues guidance within the UNEP/SETAC Life Cycle Initiative

EPA Science Inventory

Increasing needs for decision support and advances in scientific knowledge within life cycle assessment (LCA) led to substantial efforts to provide global guidance on environmental life cycle impact assessment (LCIA) indicators under the auspices of the UNEP-SETAC Life Cycle Init...

Comparison of flexible fuel vehicle and life-cycle fuel consumption and emissions of selected pollutants and greenhouse gases for ethanol 85 versus gasoline.

PubMed

Zhai, Haibo; Frey, H Christopher; Rouphail, Nagui M; Gonçalves, Gonçalo A; Farias, Tiago L

2009-08-01

The objective of this research is to evaluate differences in fuel consumption and tailpipe emissions of flexible fuel vehicles (FFVs) operated on ethanol 85 (E85) versus gasoline. Theoretical ratios of fuel consumption and carbon dioxide (CO2) emissions for both fuels are estimated based on the same amount of energy released. Second-by-second fuel consumption and emissions from one FFV Ford Focus fueled with E85 and gasoline were measured under real-world traffic conditions in Lisbon, Portugal, using a portable emissions measurement system (PEMS). Cycle average dynamometer fuel consumption and emission test results for FFVs are available from the U.S. Department of Energy, and emissions certification test results for ethanol-fueled vehicles are available from the U.S. Environmental Protection Agency. On the basis of the PEMS data, vehicle-specific power (VSP)-based modal average fuel and emission rates for both fuels are estimated. For E85 versus gasoline, empirical ratios of fuel consumption and CO2 emissions agree within a margin of error to the theoretical expectations. Carbon monoxide (CO) emissions were found to be typically lower. From the PEMS data, nitric oxide (NO) emissions associated with some higher VSP modes are higher for E85. From the dynamometer and certification data, average hydrocarbon (HC) and nitrogen oxides (NOx) emission differences vary depending on the vehicle. The differences of average E85 versus gasoline emission rates for all vehicle models are -22% for CO, 12% for HC, and -8% for NOx emissions, which imply that replacing gasoline with E85 reduces CO emissions, may moderately decrease NOx tailpipe emissions, and may increase HC tailpipe emissions. On a fuel life cycle basis for corn-based ethanol versus gasoline, CO emissions are estimated to decrease by 18%. Life-cycle total and fossil CO2 emissions are estimated to decrease by 25 and 50%, respectively; however, life-cycle HC and NOx emissions are estimated to increase by 18 and 82%, respectively.

Ni-MH storage test and cycle life test

NASA Technical Reports Server (NTRS)

Dell, R. Dan; Klein, Glenn C.; Schmidt, David F.

1994-01-01

Gates Aerospace Batteries is conducting two long term test programs to fully characterize the NiMH cell technology for aerospace applications. The first program analyzes the effects of long term storage upon cell performance. The second program analyzes cycle life testing and preliminary production lot testing. This paper summarizes these approaches to testing the NiMH couple and culminates with initial storage and testing recommendations. Long term storage presents challenges to deter the adverse condition of capacity fade in NiMH cells. Elevated but stabilized pressures and elevated but stabilized end-of-charge voltages also appear to be a characteristic phenomenon of long term storage modes. However, the performance degradation is dependent upon specific characteristics of the metal-hydride alloy. To date, there is no objective evidence with which to recommend the proper method for storage and handling of NiMH cells upon shipment. This is particularly critical due to limited data points that indicate open circuit storage at room temperature for 60 to 90 days will result in irrecoverable capacity loss. Accordingly a test plan was developed to determine what method of mid-term to long-term storage will prevent irrecoverable capacity loss. The explicit assumption is that trickle charging at some rate above the self-discharge rate will prevent the irreversible chemical changes to the negative electrode that result in the irrecoverable capacity loss. Another premise is that lower storage temperatures, typically 0 C for aerospace customers, will impede any negative chemical reactions. Three different trickle charge rates are expected to yield a fairly flat response with respect to recoverable capacity versus baseline cells in two different modes of open circuit. Specific attributes monitored include: end-of-charge voltage, end-of-charge pressure, mid-point discharge voltage, capacity, and end-of-discharge pressure. Cycle life testing and preliminary production lot testing continue to dominate the overall technology development effort at GAB. The cell life test program reflects continuing improvements in baseline cell designs. Performance improvements include lower and more stable charge voltages and pressures. The continuing review of production lot testing assures conformance to the design criteria and expectations. This is especially critical during this period of transferring technology from research and development status to production.

The Model Life-cycle: Training Module

EPA Pesticide Factsheets

Model Life-Cycle includes identification of problems & the subsequent development, evaluation, & application of the model. Objectives: define ‘model life-cycle’, explore stages of model life-cycle, & strategies for development, evaluation, & applications.

10 CFR 434.607 - Life cycle cost analysis criteria.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 10 Energy 3 2011-01-01 2011-01-01 false Life cycle cost analysis criteria. 434.607 Section 434.607... HIGH RISE RESIDENTIAL BUILDINGS Building Energy Compliance Alternative § 434.607 Life cycle cost analysis criteria. 607.1 The following life cycle cost criteria applies to the fuel selection requirements...

77 FR 38766 - Proposed Information Collection; Comment Request; International Client Life-Cycle Multi-Purpose...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-06-29

... Request; International Client Life-Cycle Multi-Purpose Forms AGENCY: International Trade Administration... aspects of an international organization's life-cycle with CS. CS is mandated by Congress to help U.S... trade events to U.S. organizations. The International Client Life-cycle Multi-Purpose Forms, previously...

10 CFR 435.8 - Life-cycle costing.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 10 Energy 3 2011-01-01 2011-01-01 false Life-cycle costing. 435.8 Section 435.8 Energy DEPARTMENT... BUILDINGS Mandatory Energy Efficiency Standards for Federal Low-Rise Residential Buildings. § 435.8 Life-cycle costing. Each Federal agency shall determine life-cycle cost-effectiveness by using the procedures...

77 FR 38582 - Proposed Information Collection; Comment Request; Domestic Client Life-Cycle Multi-Purpose Forms

Federal Register 2010, 2011, 2012, 2013, 2014

2012-06-28

... Request; Domestic Client Life-Cycle Multi-Purpose Forms AGENCY: International Trade Administration. ACTION... life-cycle with CS. CS is mandated by Congress to help U.S. organizations, particularly small and... Client Life-cycle Multi-Purpose Forms, previously titled Export Information Services Order Forms, are...

10 CFR 434.607 - Life cycle cost analysis criteria.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 10 Energy 3 2010-01-01 2010-01-01 false Life cycle cost analysis criteria. 434.607 Section 434.607... HIGH RISE RESIDENTIAL BUILDINGS Building Energy Compliance Alternative § 434.607 Life cycle cost analysis criteria. 607.1 The following life cycle cost criteria applies to the fuel selection requirements...

10 CFR 435.8 - Life-cycle costing.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 10 Energy 3 2010-01-01 2010-01-01 false Life-cycle costing. 435.8 Section 435.8 Energy DEPARTMENT... BUILDINGS Mandatory Energy Efficiency Standards for Federal Low-Rise Residential Buildings. § 435.8 Life-cycle costing. Each Federal agency shall determine life-cycle cost-effectiveness by using the procedures...

US Federal LCA Commons Life Cycle Inventory Unit Process Template

EPA Science Inventory

The US Federal LCA Commons Life Cycle Inventory Unit Process Template is a multi-sheet Excel template for life cycle inventory data, metadata and other documentation. The template comes as a package that consistent of three parts: (1) the main template itself for life cycle inven...

76 FR 41525 - Hewlett Packard Global Parts Supply Chain, Global Product Life Cycles Management Unit Including...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-07-14

... Parts Supply Chain, Global Product Life Cycles Management Unit Including Teleworkers Reporting to... workers of Hewlett Packard, Global Parts Supply Chain, Global Product Life Cycles Management Unit...). Since eligible workers of Hewlett Packard, Global Parts Supply Chain, Global Product Life Cycles...

7 CFR 2902.8 - Determining life cycle costs, environmental and health benefits, and performance.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 15 2010-01-01 2010-01-01 false Determining life cycle costs, environmental and... DESIGNATING BIOBASED PRODUCTS FOR FEDERAL PROCUREMENT General § 2902.8 Determining life cycle costs, environmental and health benefits, and performance. (a) Providing information on life cycle costs and...

77 FR 50724 - Developing Software Life Cycle Processes for Digital Computer Software Used in Safety Systems of...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-08-22

... NUCLEAR REGULATORY COMMISSION [NRC-2012-0195] Developing Software Life Cycle Processes for Digital... Software Life Cycle Processes for Digital Computer Software used in Safety Systems of Nuclear Power Plants... clarifications, the enhanced consensus practices for developing software life-cycle processes for digital...

Mathematical modeling of thermal stresses in basic oxygen furnace hood tubes

NASA Astrophysics Data System (ADS)

Samarasekera, I. V.

1985-06-01

The stress-strain history of Basic Oxygen Furnace hood tubes during thermal cycling has been computed using heat flow and stress analyses. The steady-state temperature distribution in a transverse section of the tube was computed at a location where gas temperature in the hood could be expected to be a maximum. Calculations were performed for peak gas temperatures in the range 1950 to 2480 °C (3500 to 4500 °F). The stress-strain history of an element of material located at the center of the tube hot face was traced for three consecutive cycles using elasto-plastic finite-element analysis. It has been shown that the state of stress in the element alternates between compression and tension as the tube successively heats and cools. Yielding and plastic flow occurs at the end of each half of a given cycle. It was postulated that owing to repctitive yielding, plastic strain energy accumulates causing failure of the tubes by fatigue in the low cycle region. Using fatigue theory a conservative estimate for tube life was arrived at. In-plant observations support this mechanism of failure, and the number of cycles within which tube cracking was observed compares reasonably with model predictions. Utilizing the heat flow and stress models it was recommended that tube life could be enhanced by changing the tube material to ARMCO 17-4 pH or AISI 405 steel or alternatively reconstructing hoods with AISI 316L tubes of reduced thickness. These recommendations were based on the criterion that low-cycle fatigue failure could be averted if the magnitude of the cyclic strain could be reduced or if macroscopic plastic flow could be prevented.

Inequalities in US Life Expectancy by Area Unemployment Level, 1990–2010

PubMed Central

Singh, Gopal K.; Siahpush, Mohammad

2016-01-01

This study examined the association between unemployment and life expectancy in the United States during 1990–2010. Census-based unemployment rates were linked to US county-level mortality data. Life expectancies were calculated by age, sex, race, and unemployment level during 1990–2010. Differences in life expectancy were decomposed by age and cause of death. Life expectancy was consistently lower in areas with higher unemployment rates. In 2006–2010, those in areas with high unemployment rates (≥9%) had a life expectancy of 76.9 years, compared with 80.7 years for those in areas with low unemployment rates (<3%). The association between unemployment and life expectancy was stronger for men than for women. Life expectancy ranged from 69.9 years among black men in high unemployment areas to 90.0 years among Asian/Pacific Islander women in low unemployment areas. Disparities persisted over time. In 1990–1992, life expectancy was 4.7 years shorter in high unemployment than in low unemployment areas. In 2006–2010, the life expectancy difference between the lowest and highest unemployment areas decreased to 3.8 years. Heart disease, cancer, homicide, unintentional injuries, diabetes, HIV/AIDS, and liver cirrhosis contributed most to the lower life expectancy in high unemployment areas. High unemployment areas recorded larger gains in life expectancy than low unemployment areas, contributing to the narrowing gap during 1990–2010. PMID:27073716

Life cycle replacement by gene introduction under an allee effect in periodical cicadas.

PubMed

Nariai, Yukiko; Hayashi, Saki; Morita, Satoru; Umemura, Yoshitaka; Tainaka, Kei-ichi; Sota, Teiji; Cooley, John R; Yoshimura, Jin

2011-04-06

Periodical cicadas (Magicicada spp.) in the USA are divided into three species groups (-decim, -cassini, -decula) of similar but distinct morphology and behavior. Each group contains at least one species with a 17-year life cycle and one with a 13-year cycle; each species is most closely related to one with the other cycle. One explanation for the apparent polyphyly of 13- and 17-year life cycles is that populations switch between the two cycles. Using a numerical model, we test the general feasibility of life cycle switching by the introduction of alleles for one cycle into populations of the other cycle. Our results suggest that fitness reductions at low population densities of mating individuals (the Allee effect) could play a role in life cycle switching. In our model, if the 13-year cycle is genetically dominant, a 17-year cycle population will switch to a 13-year cycle given the introduction of a few 13-year cycle alleles under a moderate Allee effect. We also show that under a weak Allee effect, different year-classes ("broods") with 17-year life cycles can be generated. Remarkably, the outcomes of our models depend only on the dominance relationships of the cycle alleles, irrespective of any fitness advantages.

Life prediction modeling based on cyclic damage accumulation

NASA Technical Reports Server (NTRS)

Nelson, Richard S.

1988-01-01

A high temperature, low cycle fatigue life prediction method was developed. This method, Cyclic Damage Accumulation (CDA), was developed for use in predicting the crack initiation lifetime of gas turbine engine materials, where initiation was defined as a 0.030 inch surface length crack. A principal engineering feature of the CDA method is the minimum data base required for implementation. Model constants can be evaluated through a few simple specimen tests such as monotonic loading and rapic cycle fatigue. The method was expanded to account for the effects on creep-fatigue life of complex loadings such as thermomechanical fatigue, hold periods, waveshapes, mean stresses, multiaxiality, cumulative damage, coatings, and environmental attack. A significant data base was generated on the behavior of the cast nickel-base superalloy B1900+Hf, including hundreds of specimen tests under such loading conditions. This information is being used to refine and extend the CDA life prediction model, which is now nearing completion. The model is also being verified using additional specimen tests on wrought INCO 718, and the final version of the model is expected to be adaptable to most any high-temperature alloy. The model is currently available in the form of equations and related constants. A proposed contract addition will make the model available in the near future in the form of a computer code to potential users.

The dynamics of resource allocation and costs of reproduction in a sexually dimorphic, wind-pollinated dioecious plant.

PubMed

Teitel, Z; Pickup, M; Field, D L; Barrett, S C H

2016-01-01

Sexual dimorphism in resource allocation is expected to change during the life cycle of dioecious plants because of temporal differences between the sexes in reproductive investment. Given the potential for sex-specific differences in reproductive costs, resource availability may contribute to variation in reproductive allocation in females and males. Here, we used Rumex hastatulus, a dioecious, wind-pollinated annual plant, to investigate whether sexual dimorphism varies with life-history stage and nutrient availability, and determine whether allocation patterns differ depending on reproductive commitment. To examine if the costs of reproduction varied between the sexes, reproduction was either allowed or prevented through bud removal, and biomass allocation was measured at maturity. In a second experiment to assess variation in sexual dimorphism across the life cycle, and whether this varied with resource availability, plants were grown in high and low nutrients and allocation to roots, aboveground vegetative growth and reproduction were measured at three developmental stages. Males prevented from reproducing compensated with increased above- and belowground allocation to a much larger degree than females, suggesting that male reproductive costs reduce vegetative growth. The proportional allocation to roots, reproductive structures and aboveground vegetative growth varied between the sexes and among life-cycle stages, but not with nutrient treatment. Females allocated proportionally more resources to roots than males at peak flowering, but this pattern was reversed at reproductive maturity under low-nutrient conditions. Our study illustrates the importance of temporal dynamics in sex-specific resource allocation and provides support for high male reproductive costs in wind-pollinated plants. © 2015 German Botanical Society and The Royal Botanical Society of the Netherlands.

Consequential environmental and economic life cycle assessment of green and gray stormwater infrastructures for combined sewer systems.

PubMed

Wang, Ranran; Eckelman, Matthew J; Zimmerman, Julie B

2013-10-01

A consequential life cycle assessment (LCA) is conducted to evaluate the trade-offs between water quality improvements and the incremental climate, resource, and economic costs of implementing green (bioretention basin, green roof, and permeable pavement) versus gray (municipal separate stormwater sewer systems, MS4) alternatives of stormwater infrastructure expansions against a baseline combined sewer system with combined sewer overflows in a typical Northeast US watershed for typical, dry, and wet years. Results show that bioretention basins can achieve water quality improvement goals (e.g., mitigating freshwater eutrophication) for the least climate and economic costs of 61 kg CO2 eq. and $98 per kg P eq. reduction, respectively. MS4 demonstrates the minimum life cycle fossil energy use of 42 kg oil eq. per kg P eq. reduction. When integrated with the expansion in stormwater infrastructure, implementation of advanced wastewater treatment processes can further reduce the impact of stormwater runoff on aquatic environment at a minimal environmental cost (77 kg CO2 eq. per kg P eq. reduction), which provides support and valuable insights for the further development of integrated management of stormwater and wastewater. The consideration of critical model parameters (i.e., precipitation intensity, land imperviousness, and infrastructure life expectancy) highlighted the importance and implications of varying local conditions and infrastructure characteristics on the costs and benefits of stormwater management. Of particular note is that the impact of MS4 on the local aquatic environment is highly dependent on local runoff quality indicating that a combined system of green infrastructure prior to MS4 potentially provides a more cost-effective improvement to local water quality.

Why is the gender gap in life expectancy decreasing? The impact of age- and cause-specific mortality in Sweden 1997-2014.

PubMed

Sundberg, Louise; Agahi, Neda; Fritzell, Johan; Fors, Stefan

2018-04-13

To enhance the understanding of the current increase in life expectancy and decreasing gender gap in life expectancy. We obtained data on underlying cause of death from the National Board of Health and Welfare in Sweden for 1997 and 2014 and used Arriaga's method to decompose life expectancy by age group and 24 causes of death. Decreased mortality from ischemic heart disease had the largest impact on the increased life expectancy of both men and women and on the decreased gender gap in life expectancy. Increased mortality from Alzheimer's disease negatively influenced overall life expectancy, but because of higher female mortality, it also served to decrease the gender gap in life expectancy. The impact of other causes of death, particularly smoking-related causes, decreased in men but increased in women, also reducing the gap in life expectancy. This study shows that a focus on overall changes in life expectancies may hide important differences in age- and cause-specific mortality. It also emphasizes the importance of addressing modifiable lifestyle factors to reduce avoidable mortality.

Effect of KOH concentration on LEO cycle life of IPV nickel-hydrogen flight cells. An update

NASA Technical Reports Server (NTRS)

Smithrick, John J.; Hall, Stephen W.

1991-01-01

An update of validation test results confirming the breakthrough in LEO cycle life of nickel-hydrogen cells containing 26 percent potassium hydroxide (KOH) electrolyte is presented. A breakthrough in the LEO cycle life of individual pressure vessel nickel-hydrogen cells is reported. The cycle life of boiler plate cells containing 26 percent KOH electrolyte was about 40,000 LEO cycles compared to 3500 cycles for cells containing 31 percent KOH.

Effect of KOH concentration on LEO cycle life of IPV nickel-hydrogen flight cells - An update

NASA Technical Reports Server (NTRS)

Smithrick, John J.; Hall, Stephen W.

1991-01-01

An update of validation test results confirming the breakthrough in LEO cycle life of nickel-hydrogen cells containing 26 percent potassium hydroxide (KOH) electrolyte is presented. A breakthrough in the LEO cycle life of individual pressure vessel nickel-hydrogen cells is reported. The cycle life of boiler plate cells containing 26 percent KOH electrolyte was about 40,000 LEO cycles compared to 3500 cycles for cells containing 31 percent KOH.

Changes in Australian women's perception of the menopause and menopausal symptoms before and after the climacteric.

PubMed

Abraham, S; Llewellyn-Jones, D; Perz, J

1994-12-01

The symptoms and perceptions of menopause of 60 Australian women were studied, by questionnaire, when they were premenopausal and 10 years later when they were postmenopausal. Menopausal symptoms expected and experienced by the women were compared, fewer women experiencing hot flushes, headache, depression and nervousness and more experiencing insomnia, increase in appetite, abdominal fullness, numbness and muscular problems. The symptoms women thought were due to hormonal changes at menopause were compared. In 1993 more women cited osteoporosis, insomnia, loss of libido, obesity and loss of muscle tone as due to hormone change while fewer cited depression. The premenstrual symptoms and their severity experienced by a woman when she was premenopausal significantly predicts the type and severity of the menopausal symptoms experienced by the woman. The expected menopausal symptoms and their severity cited by a woman also significantly predicts the type of severity of the menopausal symptoms experienced. More premenstrual symptoms predict the menopausal symptoms than those menopausal symptoms the women expected. The expectation menopause will be 'a relief' or 'a nuisance' significantly predicted the overall menopause experience described by the women. Their negative attitudes about doctors' understanding and information available about menopause remained unchanged but they forget menstrual cycle problems over the 10 years. The results suggest a possible physiological basis for premenstrual and menopausal symptoms. Assistance for women with their premenstrual and menstrual cycle symptoms may improve their quality of life at menopause.

The Sphinx's Riddle: Life and Career Cycles.

ERIC Educational Resources Information Center

Burack, Elmer H.

1984-01-01

Career cycles should be considered apart from life cycles, even though the two are interrelated. This essay examines five theories about life and career cycles, and offers insights into their limitations and potential uses. (JB)

Investigation of the environmental implications of the CNT switch through its life cycle

NASA Astrophysics Data System (ADS)

Dahlben, Lindsay Johanna

Carbon nanotubes (CNTs) are unique allotropes of carbon that have high tensile strength, a high Young's modulus, good thermal conductivity, and depending on the CNT chirality can be metallic or semiconducting. These mechanical, thermal, and electrical properties make CNTs an attractive element in electronic applications such as conductive films, photovoltaics, non-volatile memory devices, batteries, sensors, and displays. Although commercialization of CNT-enabled products is increasing, there remains a significant lack of information regarding the health effects and environmental impacts of CNTs. Some studies have even shown that the behavior, toxicity, and persistence of CNTs may differ from bulk heterogeneous carbon. Given these uncertainties, it is prudent to assess the environmental attributes of CNT products and processes now to discover and potentially prevent adverse effects. This study investigates the environmental implications of a non-volatile bi-stable electromechanical CNT switch through its life cycle. Life cycle assessment (LCA) methodology is used to track the environmental impacts of the CNT switch through its fabrication and expected use and end-of-life (EOL) stages. Process parameters, energy consumption, input materials, output emissions, and yield efficiencies are determined for the laboratory and full-scale manufacture environments. The Ecoinvent(TM) inventory database and Eco-indicator 1999(TM) method are utilized for the impact assessment. Results for the fabrication stage are reported for highest contributions to environmental impact such as airborne inorganics, land use, and fossil fuels due to Au refining processes and electricity consumption. Extension of the LCA scope is evaluated for the potential replacement of CNT switches to current field-effect transistors (FETs) in flash memory for a cellular phone application. First-order predictions are made for the functionality and performance of the CNT switch during the use stage through an environmental perspective. Existing cellular phone EOL management options including recycling and direct disposal to landfill and incineration are evaluated for potential limitations, concerns, and environmental releases that may occur from the assimilation of CNT switch-enabled phones into the waste stream. In this manner, potential environmental effects of the CNT switch throughout its life cycle stages can be addressed alongside its technological development to ensure safe, sustainable, and successful CNT products.

Life Cycle Energy Analysis of Reclaimed Water Reuse Projects in Beijing.

PubMed

Fan, Yupeng; Guo, Erhui; Zhai, Yuanzheng; Chang, Andrew C; Qiao, Qi; Kang, Peng

2018-01-01

  To illustrate the benefits of water reuse project, the process-based life cycle analysis (LCA) could be combined with input-output LCA to evaluate the water reuse project. Energy is the only evaluation parameter used in this study. Life cycle assessment of all energy inputs (LCEA) is completed mainly by the life cycle inventory (LCI), taking into account the full life cycle including the construction, the operation, and the demolition phase of the project. Assessment of benefit from water reuse during the life cycle should focus on wastewater discharge reduction and water-saving benefits. The results of LCEA of Beijing water reuse project built in 2014 in a comprehensive way shows that the benefits obtained from the reclaimed water reuse far exceed the life cycle energy consumption. In this paper, the authors apply the LCEA model to estimate the benefits of reclaimed water reuse projects quantitatively.

Long and happy living: Trends and patterns of happy life expectancy in the U.S., 1970–2000

PubMed Central

Yang, Yang

2013-01-01

This study assesses the trends and differentials in length of quality life in the U.S. population as measured by happy life expectancy in 1970, 1980, 1990, and 2000. The analysis combines age-specific prevalence rates of subjective well-being from a large nationally representative survey and life table estimates of mortality in decennial Census years. Employing the period prevalence-rate life table method—Sullivan method, the analysis finds evidence for improvement in quality of life in the U.S. Happy life expectancy largely increased in both absolute terms (number of years) and relative terms (proportion of life) over time at all adult ages examined. And increases in total life expectancy were mainly contributed by increases in expectancy in happy years rather than unhappy years. Happy life expectancy is longer than active life expectancy. And there has been greater compression of unhappiness than compression of morbidity. There are substantial differentials in happy life expectancy by sex and race because of differential prevalence rates of happiness. Women and whites had longer years of total and happy life expectancies at most ages and dates, while men and blacks had greater proportions of happy life expectancies across the three decades. Although race differentials generally decreased at older ages and with time, relative disadvantages of blacks persisted. PMID:19227700

10 CFR 436.20 - Net savings.

Code of Federal Regulations, 2013 CFR

2013-01-01

... Life Cycle Cost Analyses § 436.20 Net savings. For a retrofit project, net savings may be found by subtracting life cycle costs based on the proposed project from life cycle costs based on not having it. For a new building design, net savings is the difference between the life cycle costs of an alternative...

10 CFR 436.20 - Net savings.

Code of Federal Regulations, 2014 CFR

2014-01-01

... Life Cycle Cost Analyses § 436.20 Net savings. For a retrofit project, net savings may be found by subtracting life cycle costs based on the proposed project from life cycle costs based on not having it. For a new building design, net savings is the difference between the life cycle costs of an alternative...

10 CFR 436.42 - Evaluation of Life-Cycle Cost Effectiveness.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 10 Energy 3 2014-01-01 2014-01-01 false Evaluation of Life-Cycle Cost Effectiveness. 436.42... PROGRAMS Agency Procurement of Energy Efficient Products § 436.42 Evaluation of Life-Cycle Cost...) ENERGY STAR qualified and FEMP designated products may be assumed to be life-cycle cost-effective. (b) In...

10 CFR 435.306 - Selecting a life cycle effective proposed building design.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 10 Energy 3 2013-01-01 2013-01-01 false Selecting a life cycle effective proposed building design... Residential Buildings § 435.306 Selecting a life cycle effective proposed building design. In selecting... prototype, has the highest Net Savings or lowest total life cycle costs calculated in compliance with...

10 CFR 436.42 - Evaluation of Life-Cycle Cost Effectiveness.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 10 Energy 3 2012-01-01 2012-01-01 false Evaluation of Life-Cycle Cost Effectiveness. 436.42... PROGRAMS Agency Procurement of Energy Efficient Products § 436.42 Evaluation of Life-Cycle Cost...) ENERGY STAR qualified and FEMP designated products may be assumed to be life-cycle cost-effective. (b) In...

10 CFR 436.42 - Evaluation of Life-Cycle Cost Effectiveness.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 10 Energy 3 2013-01-01 2013-01-01 false Evaluation of Life-Cycle Cost Effectiveness. 436.42... PROGRAMS Agency Procurement of Energy Efficient Products § 436.42 Evaluation of Life-Cycle Cost...) ENERGY STAR qualified and FEMP designated products may be assumed to be life-cycle cost-effective. (b) In...

10 CFR 435.306 - Selecting a life cycle effective proposed building design.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 10 Energy 3 2014-01-01 2014-01-01 false Selecting a life cycle effective proposed building design... Residential Buildings § 435.306 Selecting a life cycle effective proposed building design. In selecting... prototype, has the highest Net Savings or lowest total life cycle costs calculated in compliance with...

10 CFR 435.306 - Selecting a life cycle effective proposed building design.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 10 Energy 3 2012-01-01 2012-01-01 false Selecting a life cycle effective proposed building design... Residential Buildings § 435.306 Selecting a life cycle effective proposed building design. In selecting... prototype, has the highest Net Savings or lowest total life cycle costs calculated in compliance with...

10 CFR 436.20 - Net savings.

Code of Federal Regulations, 2012 CFR

2012-01-01

... Life Cycle Cost Analyses § 436.20 Net savings. For a retrofit project, net savings may be found by subtracting life cycle costs based on the proposed project from life cycle costs based on not having it. For a new building design, net savings is the difference between the life cycle costs of an alternative...

10 CFR 433.8 - Life-cycle costing.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 10 Energy 3 2011-01-01 2011-01-01 false Life-cycle costing. 433.8 Section 433.8 Energy DEPARTMENT... FEDERAL COMMERCIAL AND MULTI-FAMILY HIGH-RISE RESIDENTIAL BUILDINGS § 433.8 Life-cycle costing. Each Federal agency shall determine life-cycle cost-effectiveness by using the procedures set out in subpart A...

78 FR 47012 - Developing Software Life Cycle Processes Used in Safety Systems of Nuclear Power Plants

Federal Register 2010, 2011, 2012, 2013, 2014

2013-08-02

... NUCLEAR REGULATORY COMMISSION [NRC-2012-0195] Developing Software Life Cycle Processes Used in... revised regulatory guide (RG), revision 1 of RG 1.173, ``Developing Software Life Cycle Processes for... Developing a Software Project Life Cycle Process,'' issued 2006, with the clarifications and exceptions as...

10 CFR 433.8 - Life-cycle costing.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 10 Energy 3 2010-01-01 2010-01-01 false Life-cycle costing. 433.8 Section 433.8 Energy DEPARTMENT... FEDERAL COMMERCIAL AND MULTI-FAMILY HIGH-RISE RESIDENTIAL BUILDINGS § 433.8 Life-cycle costing. Each Federal agency shall determine life-cycle cost-effectiveness by using the procedures set out in subpart A...

DEVELOPMENT OF THE METHOD AND U.S. NORMALIZATION DATABASE FOR LIFE CYCLE IMPACT ASSESSMENT AND SUSTAINABILITY METRICS

EPA Science Inventory

Normalization is an optional step within Life Cycle Impact Assessment (LCIA) that may be used to assist in the interpretation of life cycle inventory data as well as, life cycle impact assessment results. Normalization transforms the magnitude of LCI and LCIA results into relati...

10 CFR 436.42 - Evaluation of Life-Cycle Cost Effectiveness.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 10 Energy 3 2010-01-01 2010-01-01 false Evaluation of Life-Cycle Cost Effectiveness. 436.42... PROGRAMS Agency Procurement of Energy Efficient Products § 436.42 Evaluation of Life-Cycle Cost...) ENERGY STAR qualified and FEMP designated products may be assumed to be life-cycle cost-effective. (b) In...

10 CFR 435.306 - Selecting a life cycle effective proposed building design.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 10 Energy 3 2010-01-01 2010-01-01 false Selecting a life cycle effective proposed building design... Residential Buildings § 435.306 Selecting a life cycle effective proposed building design. In selecting... prototype, has the highest Net Savings or lowest total life cycle costs calculated in compliance with...

Residential Preferences and Moving Behavior: A Family Life Cycle Analysis.

ERIC Educational Resources Information Center

McAuley, William J.; Nutty, Cheri L.

The relationship of family life cycle changes to housing preferences and residential mobility is examined. Two residential decision-making issues are explored in detail--how family life cycle stages influence what people view as important to their choice of residential setting and what individuals at different family life cycle stages view as the…

10 CFR 436.20 - Net savings.

Code of Federal Regulations, 2010 CFR

2010-01-01

... Life Cycle Cost Analyses § 436.20 Net savings. For a retrofit project, net savings may be found by subtracting life cycle costs based on the proposed project from life cycle costs based on not having it. For a new building design, net savings is the difference between the life cycle costs of an alternative...

10 CFR 436.20 - Net savings.

Code of Federal Regulations, 2011 CFR

2011-01-01

... Life Cycle Cost Analyses § 436.20 Net savings. For a retrofit project, net savings may be found by subtracting life cycle costs based on the proposed project from life cycle costs based on not having it. For a new building design, net savings is the difference between the life cycle costs of an alternative...

10 CFR 436.42 - Evaluation of Life-Cycle Cost Effectiveness.

Code of Federal Regulations, 2011 CFR

2011-01-01

... the life-cycle cost analysis method in part 436, subpart A, of title 10 of the Code of Federal... 10 Energy 3 2011-01-01 2011-01-01 false Evaluation of Life-Cycle Cost Effectiveness. 436.42... PROGRAMS Agency Procurement of Energy Efficient Products § 436.42 Evaluation of Life-Cycle Cost...

Evaluation program for secondary spacecraft cells: Initial evaluation tests of General Electric Company, 6.0 ampere-hour nickel-cadmium spacecraft cells for the GOES-D, E and F satellite program

NASA Technical Reports Server (NTRS)

Harkness, J. D.

1979-01-01

The tests are to insure that all cells put into the life cycle program are of high quality by the screening of cells found to have electrolyte leakage, internal shorts, low capacity, or inability of any cell to recover its open-circuit voltage above 1.150 volts during the internal short test. Test limits specify those values at which a cell is to be terminated from charge or discharge. Requirements are referenced to normally expected values based on past performance of aerospace nickel-cadmium cells with demonstrated life characteristics. Recommendations for the improvement of the manufacturing processes are presented.

Initial evaluation tests of General Electric Company 26.5 ampere-hour nickel-cadmium spacecraft cells with auxiliary electrodes for the TIROS-N and NOAA-A satellites

NASA Technical Reports Server (NTRS)

Harkness, J. D.

1978-01-01

This evaluation test program had the purpose to insure that all cells put into the life cycle program are of high quality by the screening of cells found to have electrolyte leakage, internal shorts, low capacity, or inability of any cell to recover its open-circuit voltage above 1.150 volts during the internal short test. Test limits specify those values at which a cell is to be terminated from charge or discharge. Requirements are referenced to as normally expected values based on past performance of aerospace nickel-cadmium cells with demonstrated life characteristics. A requirement does not constitute a limit for discontinuance from test.

Performance and utility of satellite telemetry during field studies of free-ranging polar bears in Alaska

USGS Publications Warehouse

Garner, Gerald W.; Amstrup, Steven C.; Douglas, David C.; Gardner, Craig L.; Amlaner, Charles J.

1989-01-01

Satellite telemetry technology has been used during field studies of polar bears in Alaska since 1985. A total of 109 Platform Transmitter Terminals (PTT) have been deployed on free-ranging female polar bears that seasonally inhabit waters adjacent to the Alaskan coast. The PTTs transmitted locational and sensor data to TIROS-N polar-orbiting satellites during a duty cycle of 12 hours on/60 hours off in 1985, 1986, and 1987. Expected battery life was 13.8 months, and collars were normally removed and replaced with new or refurbished PTTs at 11-13 month intervals. Duty cycles were altered to 7-8 hours on/64-65 hours off in 1988 to prolong expected battery life to 19-21 months. Sensor data transmitted included PTT internal temperature, short term activity counts recorded at 60 second intervals, and long term activity counts for the preceding 24 or 72-hour period. Early failures of PTTs to fix location (less than 75% of expected battery life) were as high as 53% during 198501986. Subsequent improvements in battery design, including better shock insulation, improved electronic, and an improved battery system have reduced early failures to 27% in 1987-1988. The harsh environment and the degree of abuse observed in recovered collars indicate that an unavoidable failure rate of 8-10% is inherent within 60 days after deployment on polar bears. A total of 18,000 locations and 201,000 sensor messages were received from female polar bears between May 1985 and June 1988. Polar bears that were marked in Alaskan waters have been located as far south as 60°N 168°W, and as far east as 70°N 127°W in the Beaufort Sea. Polar bears in the Beaufort Sea are shared with Canada, while polar bears in the Chukchi and Bering seas are shared with the Soviet Union. The international ranges of the two hypothesized populations have been documented. Satellite telemetry has detailed the large movement patterns of polar bear over these vast areas that were previously not available using other techniques.

Study of the damage evolution function of tin silver copper in cycling

NASA Astrophysics Data System (ADS)

Qasaimeh, Awni

The present research focused on the assessment of solder joint fatigue life in microelectronics assemblies. A general concern of any reliability engineer is whether accelerated tests are relevant to field conditions. The risk of this was minimized by developing an approach to reduce the duration of an accelerated thermal cycling test, thus allowing for the use of less accelerated test conditions. For this purpose the conventional dye and pry technique was improved and used together with artificial neural networks to measure and characterize very early stages of crack growth. The same work also demonstrated a quantitative link between thermal cycling induced recrystallization and a strong acceleration of the subsequent fatigue crack growth and failure. A new study was conducted in which different combinations of annealing and isothermal cycling provided a systematic characterization of the effects of a range of individual parameters on the recrystallization. Experiments showed the ongoing coarsening of secondary precipitates to have a clear effect on recrystallization. The rate of recrystallization was also shown not to scale with the inelastic energy deposition. This means that the most popular current thermal cycling model cannot apply to SnAgCu solder joints. Recrystallization of the Sn grains is usually not the rate limiting mechanism in isothermal cycling. The crack initiation stage often takes up a much greater fraction of the overall life, and the eventual failure of BGA joints tends to involve transgranular crack growth instead. Cycling of individual solder joints allowed for monitoring of the evolution of the solder properties and the rate of inelastic energy deposition. Both the number of cycles to crack initiation and the subsequent number of cycles to failure were shown to be determined by the inelastic energy deposition. This provides for a simple model for the extrapolation of accelerated test results to the much milder cycling amplitudes characteristic of long term service conditions based on conventional Finite Element Modeling. It also offers a critical basis for the ongoing development of a practical model to account for the often dramatic break-down of Miner's rule of linear damage accumulation under variable cycling amplitudes as expected in realistic applications.

Estimating the life expectancy of companion dogs in Japan using pet cemetery data.

PubMed

Inoue, Mai; Kwan, Nigel C L; Sugiura, Katsuaki

2018-05-24

The life expectancy provides valuable information about population health. The life expectancies were evaluated in 12,039 dogs which were buried or cremated during January 2012 to March 2015. The data of dogs were collected at the eight animal cemeteries in Tokyo. The overall life expectancy of dogs was 13.7 (95% confidence interval (CI): 13.7-13.8) years. The probability of death was high in the first year of life, lowest in the fourth year, and increased exponentially after four years of age like Gompertz curve in semilog graph. The life expectancy of companion dogs in Tokyo has increased 1.67fold from 8.6 years to 13.7 years over the past three decades. Canine crossbreed life expectancy (15.1 years, 95% CI 14.9-15.3) was significantly greater than pure breed life expectancy (13.6 years, 95% CI 13.5-13.7, P<0.001). The life expectancy for male and for female dogs were 13.6 (95% CI: 13.5-13.7) and 13.5 (95% CI: 13.4-13.6) years, respectively, with no significant difference (P=0.099). In terms of the median age of death and life expectancy for major breeds, Shiba had the highest median age of death (15.8 years), life expectancy (15.5 years) and French Bulldog had the lowest median age of death (10.2 years), life expectancy (10.2 years). When considering life expectancy alone, these results suggest that the health of companion dogs in Japan has significantly improved over the past 30 years.

Peak capacity analysis of coal power in China based on full-life cycle cost model optimization

NASA Astrophysics Data System (ADS)

Yan, Xiaoqing; Zhang, Jinfang; Huang, Xinting

2018-02-01

13th five-year and the next period are critical for the energy and power reform of China. In order to ease the excessive power supply, policies have been introduced by National Energy Board especially toward coal power capacity control. Therefore the rational construction scale and scientific development timing for coal power are of great importance and paid more and more attentions. In this study, the comprehensive influence of coal power reduction policies is analyzed from diverse point of views. Full-life cycle cost model of coal power is established to fully reflect the external and internal cost. Then this model is introduced in an improved power planning optimization theory. The power planning and diverse scenarios production simulation shows that, in order to meet the power, electricity and peak balance of power system, China’s coal power peak capacity is within 1.15 ∼ 1.2 billion kilowatts before or after 2025. The research result is expected to be helpful to the power industry in 14th and 15th five-year periods, promoting the efficiency and safety of power system.

Life cycle based analysis of demands and emissions for residential water-using appliances.

PubMed

Lee, Mengshan; Tansel, Berrin

2012-06-30

Environmental impacts of energy and water demand and greenhouse gas emissions from three residential water-using appliances were analyzed using life cycle assessment (LCA) based approach in collaboration of economic input-output model. This study especially focused on indirect consumption and environmental impacts from end-use/demand phase of each appliance. Water-related activities such as water supply, water heating and wastewater treatment were included in the analysis. The results showed that environmental impacts from end-use/demand phase are most significant for the water system, particularly for the energy demand for water heating (73% for clothes washer and 93% for showerheads). Reducing water/hot water consumption during the end-use/demand phase is expected to improve the overall water-related energy burden and water use sustainability. In the analysis of optimal lifespan for appliances, the estimated values (8-21 years) using energy consumption balance approach were found to be lower than that using other methods (10-25 years). This implies that earlier replacement with efficiency models is encouraged to minimize the environmental impacts of the product. Copyright © 2012 Elsevier Ltd. All rights reserved.

Fatigue loading history reconstruction based on the rain-flow technique

NASA Technical Reports Server (NTRS)

Khosrovaneh, A. K.; Dowling, N. E.

1989-01-01

Methods are considered for reducing a non-random fatigue loading history to a concise description and then for reconstructing a time history similar to the original. In particular, three methods of reconstruction based on a rain-flow cycle counting matrix are presented. A rain-flow matrix consists of the numbers of cycles at various peak and valley combinations. Two methods are based on a two dimensional rain-flow matrix, and the third on a three dimensional rain-flow matrix. Histories reconstructed by any of these methods produce a rain-flow matrix identical to that of the original history, and as a result the resulting time history is expected to produce a fatigue life similar to that for the original. The procedures described allow lengthy loading histories to be stored in compact form.

KOH concentration effect on cycle life of nickel-hydrogen cells

NASA Technical Reports Server (NTRS)

Lim, Hong S.; Verzwyvelt, S. A.

1987-01-01

A cycle life test of Ni/H2 cells containing electrolytes of various KOH concentrations and a sintered type nickel electrode was carried out at 23 C using a 45 min accelerated low Earth orbit (LEO) cycle regime at 80 percent depth of discharge. One of three cells containing 26 percent KOH has achieved over 28,000 cycles, and the other two 19,000 cycles, without a sign of failure. Two other cells containing 31 percent KOH electrolyte, which is the concentration presently used in aerospace cells, failed after 2,979 and 3,620 cycles. This result indicates that the cycle life of the present type of Ni/H2 cells may be extended by a factor of 5 to 10 simply by lowering the KOH concentration. Long cycle life of a Ni/H2 battery at high depth-of-discharge operation is desired, particularly for an LEO spacecraft application. Typically, battery life of about 30,000 cycles is required for a five year mission in an LEO. Such a cycle life with presently available cells can be assured only at a very low depth-of-discharge operation. Results of testing already show that the cycle life of an Ni/H2 cell is tremendously improved by simply using an electrolyte of low KOH concentration.

10 CFR 455.64 - Life-cycle cost methodology.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 10 Energy 3 2011-01-01 2011-01-01 false Life-cycle cost methodology. 455.64 Section 455.64 Energy..., Hospitals, Units of Local Government, and Public Care Institutions § 455.64 Life-cycle cost methodology. (a) The life-cycle cost methodology under § 455.63(b) of this part is a systematic comparison of the...

NREL: U.S. Life Cycle Inventory Database - About the LCI Database Project

Science.gov Websites

About the LCI Database Project The U.S. Life Cycle Inventory (LCI) Database is a publicly available data collection and analysis methods. Finding consistent and transparent LCI data for life cycle and maintain the database. The 2009 U.S. Life Cycle Inventory (LCI) Data Stakeholder meeting was an

10 CFR 455.64 - Life-cycle cost methodology.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 10 Energy 3 2010-01-01 2010-01-01 false Life-cycle cost methodology. 455.64 Section 455.64 Energy..., Hospitals, Units of Local Government, and Public Care Institutions § 455.64 Life-cycle cost methodology. (a) The life-cycle cost methodology under § 455.63(b) of this part is a systematic comparison of the...

Alternative Fuels Data Center: Benefits and Considerations of Electricity

Science.gov Websites

tailpipe emissions when in all-electric mode. The life cycle emissions of an EV or PHEV depend on the low-polluting energy sources for electricity production, plug-in vehicles typically have a life cycle strong life cycle emissions benefit. Use the Vehicle Cost Calculator to compare life cycle emissions of

UTILITY OF A FULL LIFE-CYCLE COPEPOD BIOASSAY APPROACH FOR ASSESSMENT OF SEDIMENT-ASSOCIATED CONTAMINANT MIXTURES. (R825279)

EPA Science Inventory

Abstract

We compared a 21 day full life-cycle bioassay with an existing 14 day partial life-cycle bioassay for two species of meiobenthic copepods, Microarthridion littorale and Amphiascus tenuiremis. We hypothesized that full life-cycle tests would bette...

The Early Years: "Life" Science

ERIC Educational Resources Information Center

Ashbrook, Peggy

2013-01-01

Talking about death as part of a life cycle is often ignored or spoken about in hushed tones in early childhood. Books with "life cycle" in the title often do not include the death of the living organism in the information about the cycle. The concept of a complete life cycle does not appear in "A Framework for K-12 Science…

Alberta Carpenter | NREL

Science.gov Websites

cycle assessment in industrial by-product management, waste management, biofuels and manufacturing technologies Life cycle inventory database management Research Interests Life cycle assessment Life cycle inventory management Biofuels Advanced manufacturing Supply chain analysis Education Ph.D in environmental

Methods of Economic Valuation of The Health Risks Associated with Nanomaterials

NASA Astrophysics Data System (ADS)

Shalhevet, S.; Haruvy, N.

The worldwide market for nanomaterials is growing rapidly, but relatively little is still known about the potential risks associated with these materials. The potential health hazards associated with exposure to nanomaterials may lead in the future to increased health costs as well as increased economic costs to the companies involved, as has happened in the past in the case of asbestos. Therefore, it is important to make an initial estimate of the potential costs associated with these health hazards, and to prepare ahead with appropriate health insurance for individuals and financial insurance for companies. While several studies have examined the environmental and health hazards of different nanomaterials by performing life cycle impact assessments, so far these studies have concentrated on the cost of production, and did not estimate the economic impact of the health hazards. This paper discusses methods of evaluating the economic impact of potential health hazards on the public. The proposed method is based on using life cycle impact assessment studies of nanomaterials to estimate the DALYs (Disability Adjusted Life Years) associated with the increased probability of these health hazards. The economic valuation of DALY's can be carried out based on the income lost and the costs of medical treatment. The total expected increase in cost depends on the increase in the statistical probability of each disease.

Energy storage devices for future hybrid electric vehicles

NASA Astrophysics Data System (ADS)

Karden, Eckhard; Ploumen, Servé; Fricke, Birger; Miller, Ted; Snyder, Kent

Powertrain hybridization as well as electrical energy management are imposing new requirements on electrical storage systems in vehicles. This paper characterizes the associated vehicle attributes and, in particular, the various levels of hybrids. New requirements for the electrical storage system are derived, including: shallow-cycle life, high dynamic charge acceptance particularly for regenerative braking and robust service life in sustained partial-state-of-charge usage. Lead/acid, either with liquid or absorptive glass-fibre mat electrolyte, is expected to remain the predominant battery technology for 14 V systems, including micro-hybrids, and with a cost-effective battery monitoring system for demanding applications. Advanced AGM batteries may be considered for mild or even medium hybrids once they have proven robustness under real-world conditions, particularly with respect to cycle life at partial-states-of-charge and dynamic charge acceptance. For the foreseeable future, NiMH and Li-ion are the dominating current and potential battery technologies for higher-functionality HEVs. Li-ion, currently at development and demonstration stages, offers attractive opportunities for improvements in performance and cost. Supercapacitors may be considered for pulse power applications. Aside from cell technologies, attention to the issue of system integration of the battery into the powertrain and vehicle is growing. Opportunities and challenges for potential "battery pack" system suppliers are discussed.

Childhood Health Status and Adulthood Cardiovascular Disease Morbidity in Rural China: Are They Related?

PubMed

Wang, Qing; Shen, Jay J

2016-06-06

Cardiovascular diseases (CVDs) are among the top health problems of the Chinese population. Although mounting evidence suggests that early childhood health status has an enduring effect on late life chronic morbidity, no study so far has analyzed the issue in China. Using nationally representative data from the 2013 China Health and Retirement Longitudinal Study (CHARLS), a Probit model and Two-Stage Residual Inclusion estimation estimator were applied to analyze the relationship between childhood health status and adulthood cardiovascular disease in rural China. Good childhood health was associated with reduced risk of adult CVDs. Given the long-term effects of childhood health on adulthood health later on, health policy and programs to improve the health status and well-being of Chinese populations over the entire life cycle, especially in persons' early life, are expected to be effective and successful.

[Economic crisis, poverty and childhood. What are the expected short- and long-term effects for the "children of the crisis"? SESPAS report 2014].

PubMed

Flores, Manuel; García-Gómez, Pilar; Zunzunegui, María-Victoria

2014-06-01

The way a person will develop over the lifespan is largely determined by the first few years of life. A substantial share of the inequalities in health and socioeconomic status observed in adult life originate during childhood (and even while in utero). In this paper, we first review the literature on the impact of childhood conditions throughout the life cycle. We next discuss some of the social and biological mechanisms behind the transmission of the effects of poverty during the prenatal period, childhood, and adulthood. We then analyze several international experiences aimed at reducing intergenerational transmission of poverty. The article ends with some critical thoughts and policy recommendations to avoid the possible long-term effects of the current crisis on the health and socioeconomic status of the "children of the crisis" in Spain. Copyright © 2013 SESPAS. Published by Elsevier Espana. All rights reserved.

Childhood Health Status and Adulthood Cardiovascular Disease Morbidity in Rural China: Are They Related?

PubMed Central

Wang, Qing; Shen, Jay J.

2016-01-01

Cardiovascular diseases (CVDs) are among the top health problems of the Chinese population. Although mounting evidence suggests that early childhood health status has an enduring effect on late life chronic morbidity, no study so far has analyzed the issue in China. Using nationally representative data from the 2013 China Health and Retirement Longitudinal Study (CHARLS), a Probit model and Two-Stage Residual Inclusion estimation estimator were applied to analyze the relationship between childhood health status and adulthood cardiovascular disease in rural China. Good childhood health was associated with reduced risk of adult CVDs. Given the long-term effects of childhood health on adulthood health later on, health policy and programs to improve the health status and well-being of Chinese populations over the entire life cycle, especially in persons’ early life, are expected to be effective and successful. PMID:27275829

Trends in U.S. life expectancy gradients: the role of changing educational composition.

PubMed

Hendi, Arun S

2015-06-01

I examined age patterns and the role of shifting educational distributions in driving trends in educational gradients in life expectancy among non-Hispanic Whites between 1991 and 2005. Data were from the 1986-2004 National Health Interview Survey with mortality follow-up through 2006. Life expectancies were computed by sex, period and education. Age decompositions of life expectancy gradients and composition-adjusted life expectancies were computed to account for age patterns and shifting educational distributions. Life expectancy at age 25 among White men increased for all education groups, decreased among the least-educated White women and increased among White women with college degrees. Much of the decline in measured life expectancy for White women with less than a high school education comes from the 85+ age group. Educational gradients in life expectancy widened for White men and women. One-third of the gradient is due to ages below 50. Approximately 26% (0.7 years) and 87% (0.8 years) of the widening of the gradient in life expectancy between ages 25 and 85 for White women and men is attributable to shifting education distributions. Over half of the decline in temporary life expectancy among the least-educated White women is due to compositional change. Life expectancy has increased among White men for all education groups and has decreased among White women with less than a high school education, though not to the extent reported in previous studies. The fact that a large proportion of the change in education-specific life expectancy among women is due to the 85+ age group suggests changes in institutionalization may be affecting estimates. Much of the change in education-specific life expectancy and the growth in the educational gradient in life expectancy is due to the shifting distribution of individuals across education categories. © The Author 2015; all rights reserved. Published by Oxford University Press on behalf of the International Epidemiological Association.

NREL: U.S. Life Cycle Inventory Database - Publications

Science.gov Websites

Publications Planning Documents U.S. Life Cycle Inventory Database Roadmap, February 2009 U.S. Life Cycle Inventory User Survey, February 2009 U.S. LCI Database Factsheet, March 2005 User's Guide for Life

Autonomy and integration in complex parasite life cycles.

PubMed

Benesh, Daniel P

2016-12-01

Complex life cycles are common in free-living and parasitic organisms alike. The adaptive decoupling hypothesis postulates that separate life cycle stages have a degree of developmental and genetic autonomy, allowing them to be independently optimized for dissimilar, competing tasks. That is, complex life cycles evolved to facilitate functional specialization. Here, I review the connections between the different stages in parasite life cycles. I first examine evolutionary connections between life stages, such as the genetic coupling of parasite performance in consecutive hosts, the interspecific correlations between traits expressed in different hosts, and the developmental and functional obstacles to stage loss. Then, I evaluate how environmental factors link life stages through carryover effects, where stressful larval conditions impact parasites even after transmission to a new host. There is evidence for both autonomy and integration across stages, so the relevant question becomes how integrated are parasite life cycles and through what mechanisms? By highlighting how genetics, development, selection and the environment can lead to interdependencies among successive life stages, I wish to promote a holistic approach to studying complex life cycle parasites and emphasize that what happens in one stage is potentially highly relevant for later stages.

Degradation of Si/Ge core/shell nanowire heterostructures during lithiation and delithiation at 0.8 and 20 A g-1.

PubMed

Kim, Dongheun; Li, Nan; Sheehan, Chris J; Yoo, Jinkyoung

2018-04-26

Si/Ge core/shell nanowire heterostructures have been expected to provide high energy and power densities for lithium ion battery anodes due to the large capacity of Si and the high electrical and ionic conductivities of Ge. Although the battery anode performances of Si/Ge core/shell nanowire heterostructures have been characterized, the degradation of Si/Ge core/shell nanowire heterostructures has not been thoroughly investigated. Here we report the compositional and structural changes of the Si/Ge core/shell nanowire heterostructure over cycling of lithiation and delithiation at different charging rates. The Si/Ge core/shell nanowire heterostructure holds the core and shell structure at a charging rate of 0.8 A g-1 up to 50 cycles. On the other hand, compositional intermixing and loss of Si occur at a charging rate of 20 A g-1 within 50 cycles. The operation condition-dependent degradation provides a new aspect of materials research for the development of high performance lithium ion battery anodes with a long cycle life.

Lead-acid batteries in solar photovoltaic power systems for marine aids to navigation. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Trenchard, S.E.

1981-10-01

Since 1974, the U.S. Coast Guard has been testing lead-acid batteries in solar photovoltaic-powered systems for aids to navigation. Three types of lead-acid batteries, distinguished by the composition of their grid material, have been tested: lead-antimony grid, lead-calcium grid, and pure-lead grid. This report contains a comparison of the charging characteristics and the charge-discharge cycling behavior of each grid type. All types were remarkably similar qualitatively in their daily as well as annual cycling behavior but the significance of the quantitative differences offer distinctive tradeoffs. This report presents models for water usage, depth-of-discharge, and post-cycle capacity for various levels ofmore » voltage regulation. Based on the post-cycle capacity tests, the effect of grid strength, grid thickness, and operating conditions on life expectancy are presented. A final discussion presents the results of a field deployment of solar photovoltaic-powered aids to navigation in the Miami, Florida area. Potential solutions to the battery terminal corrosion and bird guano problems observed are discussed.« less

Life expectancy and national income in Europe, 1900-2008: an update of Preston's analysis.

PubMed

Mackenbach, Johan P; Looman, Caspar Wn

2013-08-01

In the past, upward shifts of the so-called Preston curve, which relates life expectancy to national income, have contributed importantly to worldwide increases in life expectancy. These shifts were due to rapid diffusion of knowledge and technology for infectious disease control from high-income to low-income countries. We assessed to what extent life expectancy growth in Europe has been accompanied by upward shifts in the relation between national income and life expectancy in later parts of the 20th century, when progress in cardiovascular disease control was the main driver of life expectancy growth. Data on national income (gross domestic product per capita, in 1990 international dollars), life expectancy and cause-specific mortality covering the period 1900-2008 were extracted from international data banks. (Change in) life expectancy and age-standardized mortality was regressed on (change in) national income, and the regression parameters were used to estimate the contribution to rising life expectancy and declining mortality in Europe as a whole of changes in national income vs shifts in the relation between national income and health outcomes. Large upward shifts in the relation between national income and life expectancy only occurred before 1960, and were due to rapid declines in mortality from infectious diseases which were independent of rises in national income. These shifts account for between two-thirds and four-fifths of the increase in life expectancy in Europe as a whole during this period. After 1960, upward shifts in the relation between national income and life expectancy were much smaller, and contributed only between one-quarter and one-half to the increase in life expectancy in Europe as a whole. During the latter period, declines in mortality from cardiovascular disease were mainly attributable to increases in national income. In contrast to earlier periods, recent life expectancy growth in European countries appears to have been dependent on their economic growth. More rapid diffusion of knowledge and technology for cardiovascular disease control from higher- to lower-income countries in Europe may be needed to close the East-West life expectancy gap, but it is unlikely that this can be achieved in the absence of more equal economic conditions.

[Life expectancy at birth in Colombia, 2000-2009: inequalities by region and gender].

PubMed

Eslava-Schmalbach, Javier H; Rincón, Carlos Javier; Guarnizo-Herreño, Carol Cristina

2013-01-01

Life expectancy is one of the measurements that have been used to monitor socioeconomic development within and among countries. During the last 30 years, life expectancy has increased worldwide mainly due to medical and technological developments. However, access to health care, new technologies and social determinants remain unevenly distributed among regions and countries in the world. To assess inequalities in life expectancy by gender and regions (departments) in Colombia between 2000 and 2009. Ecological study. Life expectancy was estimated for each Colombian department using yearly life tables from 2000 to 2009. We used data from the death registries and the estimated population series, provided by the Departamento Administrativo Nacional de Estadística (DANE). For the study period, estimates of life expectancy by departments were compared with those from Japan for the years 2000, 2006 and 2009, which is the country with the highest life expectancy in the world, and with the Colombian department with the highest life expectancy from 2000 to 2009. Compared with the highest life expectancy in the world, Colombian departments showed differences ranged between 5.7 and 21 years. We found significant differences between departments, with the largest difference being 15.3 years. Additionally, in some departments life expectancy decreased during the analyzed period. This study identified differences in life expectancy in Colombian departments suggesting inequalities in health and living conditions among them. These differences increased in some departments during the period 2000-2009.

10 CFR 436.10 - Purpose.

Code of Federal Regulations, 2010 CFR

2010-01-01

... Cycle Cost Analyses § 436.10 Purpose. This subpart establishes a methodology and procedures for estimating and comparing the life cycle costs of Federal buildings, for determining the life cycle cost effectiveness of energy conservation measures and water conservation measures, and for rank ordering life cycle...

Shortening tobacco life cycle accelerates functional gene identification in genomic research.

PubMed

Ning, G; Xiao, X; Lv, H; Li, X; Zuo, Y; Bao, M

2012-11-01

Definitive allocation of function requires the introduction of genetic mutations and analysis of their phenotypic consequences. Novel, rapid and convenient techniques or materials are very important and useful to accelerate gene identification in functional genomics research. Here, over-expression of PmFT (Prunus mume), a novel FT orthologue, and PtFT (Populus tremula) lead to shortening of the tobacco life cycle. A series of novel short life cycle stable tobacco lines (30-50 days) were developed through repeated self-crossing selection breeding. Based on the second transformation via a gusA reporter gene, the promoter from BpFULL1 in silver birch (Betula pendula) and the gene (CPC) from Arabidopsis thaliana were effectively tested using short life cycle tobacco lines. Comparative analysis among wild type, short life cycle tobacco and Arabidopsis transformation system verified that it is optional to accelerate functional gene studies by shortening host plant material life cycle, at least in these short life cycle tobacco lines. The results verified that the novel short life cycle transgenic tobacco lines not only combine the advantages of economic nursery requirements and a simple transformation system, but also provide a robust, effective and stable host system to accelerate gene analysis. Thus, shortening tobacco life cycle strategy is feasible to accelerate heterologous or homologous functional gene identification in genomic research. © 2012 German Botanical Society and The Royal Botanical Society of the Netherlands.

NREL, Johns Hopkins SAIS Develop Method to Quantify Life Cycle Land Use of

Science.gov Websites

Life Cycle Land Use of Electricity from Natural Gas News Release: NREL, Johns Hopkins SAIS Develop Method to Quantify Life Cycle Land Use of Electricity from Natural Gas October 2, 2017 A case study of time provides quantifiable information on the life cycle land use of generating electricity from

REPORT ON ACTIVITY OF TASK FORCE 1 IN THE LIFE CYCLE INVENTORY PROGRAMME: DATA REGISTRY - GLOBAL LIFE CYCLE INVENTORY DATA RESOURCES

EPA Science Inventory

This paper presents a summary of the findings of a report prepared by Task Force 1 of the UNEP/SETAC Life Cycle Initiative on the available Life Cycle Inventory (LCI) databases around the world. An update of a previous summary prepared in May 2002 by Norris and Notten, the repor...

Understanding future emissions from low-carbon power systems by integration of life-cycle assessment and integrated energy modelling

NASA Astrophysics Data System (ADS)

Pehl, Michaja; Arvesen, Anders; Humpenöder, Florian; Popp, Alexander; Hertwich, Edgar G.; Luderer, Gunnar

2017-12-01

Both fossil-fuel and non-fossil-fuel power technologies induce life-cycle greenhouse gas emissions, mainly due to their embodied energy requirements for construction and operation, and upstream CH4 emissions. Here, we integrate prospective life-cycle assessment with global integrated energy-economy-land-use-climate modelling to explore life-cycle emissions of future low-carbon power supply systems and implications for technology choice. Future per-unit life-cycle emissions differ substantially across technologies. For a climate protection scenario, we project life-cycle emissions from fossil fuel carbon capture and sequestration plants of 78-110 gCO2eq kWh-1, compared with 3.5-12 gCO2eq kWh-1 for nuclear, wind and solar power for 2050. Life-cycle emissions from hydropower and bioenergy are substantial (˜100 gCO2eq kWh-1), but highly uncertain. We find that cumulative emissions attributable to upscaling low-carbon power other than hydropower are small compared with direct sectoral fossil fuel emissions and the total carbon budget. Fully considering life-cycle greenhouse gas emissions has only modest effects on the scale and structure of power production in cost-optimal mitigation scenarios.

Joint Probabilistic Projection of Female and Male Life Expectancy

PubMed Central

Raftery, Adrian E.; Lalic, Nevena; Gerland, Patrick

2014-01-01

BACKGROUND The United Nations (UN) produces population projections for all countries every two years. These are used by international organizations, governments, the private sector and researchers for policy planning, for monitoring development goals, as inputs to economic and environmental models, and for social and health research. The UN is considering producing fully probabilistic population projections, for which joint probabilistic projections of future female and male life expectancy at birth are needed. OBJECTIVE We propose a methodology for obtaining joint probabilistic projections of female and male life expectancy at birth. METHODS We first project female life expectancy using a one-sex method for probabilistic projection of life expectancy. We then project the gap between female and male life expectancy. We propose an autoregressive model for the gap in a future time period for a particular country, which is a function of female life expectancy and a t-distributed random perturbation. This method takes into account mortality data limitations, is comparable across countries, and accounts for shocks. We estimate all parameters based on life expectancy estimates for 1950–2010. The methods are implemented in the bayesLife and bayesPop R packages. RESULTS We evaluated our model using out-of-sample projections for the period 1995–2010, and found that our method performed better than several possible alternatives. CONCLUSIONS We find that the average gap between female and male life expectancy has been increasing for female life expectancy below 75, and decreasing for female life expectancy above 75. Our projections of the gap are lower than the UN’s 2008 projections for most countries and so lead to higher projections of male life expectancy. PMID:25580082

Space Station Environmental Control and Life Support System Purge Control Pump Assembly Modeling and Analysis

NASA Technical Reports Server (NTRS)

Schunk, R. Gregory; Hunt, Patrick L. (Technical Monitor)

2001-01-01

Preliminary results from a thermal/flow analysis of the Purge Control Pump Assembly (PCPA) indicate that pump performance (mass flow rate) is enhanced via cooling of the housing and lowering of the inlet vapor quality. Under a nominal operational profile (25% duty cycle or less), at the maximum motor dissipation, it appears that the peristaltic tubing temperature will still remain significantly below the expected UPA condenser temperature (78 F max versus approximately 105 F in the condenser) permitting condensation in the pump head.

General aviation internal-combustion engine research programs at NASA-Lewis Research Center

NASA Technical Reports Server (NTRS)

Willis, E. A.

1978-01-01

An update is presented of non-turbine general aviation engine programs. The program encompasses conventional, lightweight diesel and rotary engines. It's three major thrusts are: (1) reduced SFC's; (2) improved fuels tolerance; and (3) reduced emissions. Current and planned future programs in such areas as lean operation, improved fuel management, advanced cooling techniques and advanced engine concepts, are described. These are expected to lay the technology base, by the mid to latter 1980's, for engines whose life cycle fuel costs are 30 to 50% lower than today's conventional engines.

M13 virus-directed synthesis of nanostructured metal oxides for lithium-oxygen batteries.

PubMed

Oh, Dahyun; Qi, Jifa; Han, Binghong; Zhang, Geran; Carney, Thomas J; Ohmura, Jacqueline; Zhang, Yong; Shao-Horn, Yang; Belcher, Angela M

2014-08-13

Transition metal oxides are promising electrocatalysts for both water oxidations and metal-air batteries. Here, we report the virus-mediated synthesis of cobalt manganese oxide nanowires (NWs) to fabricate high capacity Li-O2 battery electrodes. Furthermore, we hybridized Ni nanoparticles (NPs) on bio Co3O4 NWs to improve the round trip efficiency as well as the cycle life of Li-O2 batteries. This biomolecular directed synthesis method is expected to provide a selection platform for future energy storage electrocatalysts.

Performance Characteristics of Lithium-Ion Prototype Batteries for Mars Surveyor Program 2001 Lander

NASA Technical Reports Server (NTRS)

Smart, M. C.; Ratnakumar, B. V.; Whitcanack, L.; Surampudi, S.; Byers, J.; Marsh, R. A.

2000-01-01

A viewgraph presentation outlines the scientific payload, expected launch date and tasks, and an image of the Mars Surveyor 2001 Lander components. The Lander's battery specifications are given. The program objectives for the Li-ion cells for the Lander are listed, and results performance evaluation and cycle life performance tests are outlined for different temperatures. Cell charge characteristics are described, and test data is presented for charge capacity at varying temperatures. Capacity retention and storage characteristics tests are described and results are shown.

Application of life cycle assessment for an evaluation of wastewater treatment and reuse project--case study of Xi'an, China.

PubMed

Zhang, Q H; Wang, X C; Xiong, J Q; Chen, R; Cao, B

2010-03-01

In order to illuminate the benefit of a wastewater treatment and reuse project, a life cycle assessment (LCA) model was proposed by combining the process-based LCA and the input-output based LCA in one framework and using energy consumption as the sole parameter for quantitative evaluation of the project. The life cycle consumption was evaluated mainly by life cycle inventory (LCI) analysis taking into account the construction phase, operation phase and demolishment phase of the project. For evaluating the life cycle benefit of treated water reuse, attention was paid to the decrease of secondary effluent discharge and water saving. As a result of comprehensive LCA analysis of a case project in Xi'an, China, it was understood that the life cycle benefit gained from treated wastewater reuse much surpassed the life cycle energy consumption. The advantage of wastewater treatment and reuse was well shown by LCA analysis using the proposed model. 2009 Elsevier Ltd. All rights reserved.

A case study by life cycle assessment

NASA Astrophysics Data System (ADS)

Li, Shuyun

2017-05-01

This article aims to assess the potential environmental impact of an electrical grinder during its life cycle. The Life Cycle Inventory Analysis was conducted based on the Simplified Life Cycle Assessment (SLCA) Drivers that calculated from the Valuation of Social Cost and Simplified Life Cycle Assessment Model (VSSM). The detailed results for LCI can be found under Appendix II. The Life Cycle Impact Assessment was performed based on Eco-indicator 99 method. The analysis results indicated that the major contributor to the environmental impact as it accounts for over 60% overall SLCA output. In which, 60% of the emission resulted from the logistic required for the maintenance activities. This was measured by conducting the hotspot analysis. After performing sensitivity analysis, it is evidenced that changing fuel type results in significant decrease environmental footprint. The environmental benefit can also be seen from the negative output values of the recycling activities. By conducting Life Cycle Assessment analysis, the potential environmental impact of the electrical grinder was investigated.

Characterization of Dementia and Alzheimer’s Disease in an Older Population: Updated Incidence and Life Expectancy With and Without Dementia

PubMed Central

Tom, Sarah E.; Hubbard, Rebecca A.; Crane, Paul K.; Haneuse, Sebastien J.; Bowen, James; McCormick, Wayne C.; McCurry, Susan; Larson, Eric B.

2015-01-01

Objectives. We estimated dementia incidence rates, life expectancies with and without dementia, and percentage of total life expectancy without dementia. Methods. We studied 3605 members of Group Health (Seattle, WA) aged 65 years or older who did not have dementia at enrollment to the Adult Changes in Thought study between 1994 and 2008. We estimated incidence rates of Alzheimer’s disease and dementia, as well as life expectancies with and without dementia, defined as the average number of years one is expected to live with and without dementia, and percentage of total life expectancy without dementia. Results. Dementia incidence increased through ages 85 to 89 years (74.2 cases per 1000 person-years) and 90 years or older (105 cases per 1000 person-years). Life expectancy without dementia and percentage of total life expectancy without dementia decreased with age. Life expectancy with dementia was longer in women and people with at least a college degree. Percentage of total life expectancy without dementia was greater in younger age groups, men, and those with more education. Conclusions. Efforts to delay onset of dementia, if successful, would likely benefit older adults of all ages. PMID:25033130

The circle of life: A cross-cultural comparison of children's attribution of life-cycle traits.

PubMed

Burdett, Emily R R; Barrett, Justin L

2016-06-01

Do children attribute mortality and other life-cycle traits to all minded beings? The present study examined whether culture influences young children's ability to conceptualize and differentiate human beings from supernatural beings (such as God) in terms of life-cycle traits. Three-to-5-year-old Israeli and British children were questioned whether their mother, a friend, and God would be subject to various life-cycle processes: Birth, death, ageing, existence/longevity, and parentage. Children did not anthropomorphize but differentiated among human and supernatural beings, attributing life-cycle traits to humans, but not to God. Although 3-year-olds differentiated significantly among agents, 5-year-olds attributed correct life-cycle traits more consistently than younger children. The results also indicated some cross-cultural variation in these attributions. Implications for biological conceptual development are discussed. © 2015 The British Psychological Society.

Long life nickel electrodes for a nickel-hydrogen cell: Cycle life tests

NASA Technical Reports Server (NTRS)

Lim, H. S.; Verzwyvelt, S. A.

1985-01-01

In order to develop a long life nickel electrode for a Ni/H2 cell, the cycle life of nickel electrodes was tested in Ni/H2 boiler plate cells. A 19 test cell matrix was made of various nickel electrode designs including three levels each of plaque mechanical strength, median pore size of the plaque, and active material loading. Test cells were cycled to the end of their life (0.5v) in a 45 minute low Earth orbit cycle regime at 80% depth-of-discharge. It is shown that the active material loading level affects the cycle life the most with the optimum loading at 1.6 g/cc void. Mechanical strength does not affect the cycle life noticeably in the bend strength range of 400 to 700 psi. It is found that the best plaque is made of INCO nickel powder type 287 and has median pore size of 13 micron.

Plant origin and ploidy influence gene expression and life cycle characteristics in an invasive weed.

PubMed

Broz, Amanda K; Manter, Daniel K; Bowman, Gillianne; Müller-Schärer, Heinz; Vivanco, Jorge M

2009-03-23

Ecological, evolutionary and physiological studies have thus far provided an incomplete picture of why some plants become invasive; therefore we used genomic resources to complement and advance this field. In order to gain insight into the invasive mechanism of Centaurea stoebe we compared plants of three geo-cytotypes, native Eurasian diploids, native Eurasian tetraploids and introduced North American tetraploids, grown in a common greenhouse environment. We monitored plant performance characteristics and life cycle habits and characterized the expression of genes related to constitutive defense and genome stability using quantitative PCR. Plant origin and ploidy were found to have a significant effect on both life cycle characteristics and gene expression, highlighting the importance of comparing appropriate taxonomic groups in studies of native and introduced plant species. We found that introduced populations of C. stoebe exhibit reduced expression of transcripts related to constitutive defense relative to their native tetraploid counterparts, as might be expected based on ideas of enemy release and rapid evolution. Measurements of several vegetative traits were similar for all geo-cytotypes; however, fecundity of tetraploids was significantly greater than diploids, due in part to their polycarpic nature. A simulation of seed production over time predicts that introduced tetraploids have the highest fecundity of the three geo-cytotypes. Our results suggest that characterizing gene expression in an invasive species using populations from both its native and introduced range can provide insight into the biology of plant invasion that can complement traditional measurements of plant performance. In addition, these results highlight the importance of using appropriate taxonomic units in ecological genomics investigations.

Reliability and Creep/Fatigue Analysis of a CMC Component

NASA Technical Reports Server (NTRS)

Murthy, Pappu L. N.; Mital, Subodh K.; Gyekenyesi, John Z.; Gyekenyesi, John P.

2007-01-01

High temperature ceramic matrix composites (CMC) are being explored as viable candidate materials for hot section gas turbine components. These advanced composites can potentially lead to reduced weight and enable higher operating temperatures requiring less cooling; thus leading to increased engine efficiencies. There is a need for convenient design tools that can accommodate various loading conditions and material data with their associated uncertainties to estimate the minimum predicted life as well as the failure probabilities of a structural component. This paper presents a review of the life prediction and probabilistic analyses performed for a CMC turbine stator vane. A computer code, NASALife, is used to predict the life of a 2-D woven silicon carbide fiber reinforced silicon carbide matrix (SiC/SiC) turbine stator vane due to a mission cycle which induces low cycle fatigue and creep. The output from this program includes damage from creep loading, damage due to cyclic loading and the combined damage due to the given loading cycle. Results indicate that the trends predicted by NASALife are as expected for the loading conditions used for this study. In addition, a combination of woven composite micromechanics, finite element structural analysis and Fast Probability Integration (FPI) techniques has been used to evaluate the maximum stress and its probabilistic distribution in a CMC turbine stator vane. Input variables causing scatter are identified and ranked based upon their sensitivity magnitude. Results indicate that reducing the scatter in proportional limit strength of the vane material has the greatest effect in improving the overall reliability of the CMC vane.

Life expectancy and disparity: an international comparison of life table data

PubMed Central

Zhang, Zhen; van Raalte, Alyson A

2011-01-01

Objectives To determine the contribution of progress in averting premature deaths to the increase in life expectancy and the decline in lifespan variation. Design International comparison of national life table data from the Human Mortality Database. Setting 40 developed countries and regions, 1840–2009. Population Men and women of all ages. Main outcome measure We use two summary measures of mortality: life expectancy and life disparity. Life disparity is a measure of how much lifespans differ among individuals. We define a death as premature if postponing it to a later age would decrease life disparity. Results In 89 of the 170 years from 1840 to 2009, the country with the highest male life expectancy also had the lowest male life disparity. This was true in 86 years for female life expectancy and disparity. In all years, the top several life expectancy leaders were also the top life disparity leaders. Although only 38% of deaths were premature, fully 84% of the increase in life expectancy resulted from averting premature deaths. The reduction in life disparity resulted from reductions in early-life disparity, that is, disparity caused by premature deaths; late-life disparity levels remained roughly constant. Conclusions The countries that have been the most successful in averting premature deaths have consistently been the life expectancy leaders. Greater longevity and greater equality of individuals' lifespans are not incompatible goals. Countries can achieve both by reducing premature deaths. PMID:22021770

Increase Return on Investment of Software Development Life Cycle by Managing the Risk - A Case Study

DTIC Science & Technology

2015-04-01

for increasing the return on investment during the Software Development Life Cycle ( SDLC ) through selected quantitative analyses employing both the...defect rate, return on investment (ROI), software development life cycle ( SDLC ) DE FE N SE A C Q U IS IT IO N UN IVERSITY ALU M N I A SSO C IATIO N R...becomes comfortable due to its intricacies and learning cycle. The same may be said with respect to software development life cycle ( SDLC ) management

LIFE CYCLE ASSESSMENT FOR PC BLEND 2 AIRCRAFT RADOME DEPAINTER

EPA Science Inventory

This report describes the life cycle assessment on a potential replacement solvent blend for aircraft radome depainting at the Oklahoma City Air Logistics Center at Tinker Air Force Base. The life cycle assessment is composed of three separate but interrelated components: life cy...

Working life tables, Bangladesh 1981.

PubMed

Matin, K A

1986-06-01

Data from the 1981 Bangladesh Population Census were used to construct life tables for working men and women. Bangladesh has a dependency burden of 109 dependents to 100 economically active population. Labor force participation rates in 1981 were 74.1/100 population aged 10 years and over for males and 4.3/100 population aged 10 years and over for females. The age-specific economic activity rates provided the essential link in translating life table data to working life table data. It was calculated that a newborn Bangladesh male had a working life expectancy of 37.8 years and an overall life expectancy of 50.0 years; working life expectancy peaks at 44.2 years at 10 years of age. A newborn female has a working life expectancy of 1.8 years and an overall life expectancy of 49.0 years; a maximum working life expectancy of 2.4 years is obtained at 10 years of age. In the period 1962-81, male working life expectancy registered a slight decline at all ages, while female working life expectancy increased by about 6 months for ages up to 30 years. Mortality accounts for a loss of about 10% of gross years of active life in the 10-69-year goups and 20% in the 10-79-year age group. The male working life expectancy values for Bangladesh in 1981 correspond well with those found in India in 1971, Pakistan in 1978, and Sri Lanka in 1971. However, there is wide divergency in terms of female working life expectancy values: such rates were significantly higher in Sri Lanka and India than in Bangladesh up to the age of 30 years, after which point there was little divergence.

What drives seasonal fluctuations of body condition in a semelparous income breeder octopus?

NASA Astrophysics Data System (ADS)

Quetglas, Antoni; Ordines, Francesc; Valls, Maria

2011-09-01

The vast majority of modern cephalopods is single-season breeders, or semelparous in the strict sense, that die soon after the reproduction takes place. Individual body condition in these marine invertebrates is expected to be highly affected by reproduction because: 1) the gonad weight of females, which represents <1% of body weight when immature, increases up to 20-50% during maturation; and 2) octopus females reduce or even cease their food intake during breeding. Based on this expectation, we analysed the interrelationship between condition and reproduction in the temperate octopus Eledone cirrhosa. Results from a previous work using biochemical analyses showed that reproduction in this species is not fuelled by stored reserves (capital breeder), but by food intakes (income breeder). Since income breeders depend strongly on food resources, the effect of several environmental variables related to food availability such as primary production, sea temperature (ST) and river discharges were also analysed. Condition showed a marked intrannual cycle independently of the sex and, noteworthy, the maturity stage. Given that immature individuals are not expected to display seasonal fluctuations in body condition related to maturation, these results preclude reproduction as a driving factor for the observed circannual cycle. Condition was significantly correlated with all the environmental variables analysed, except with ST at the depths where the species lives. Although this last result also precludes concurrent ST as a driving factor of body condition, those correlations suggest that condition might display an intrinsic seasonal cycle, as many other life-history traits in most species such as reproduction, migration or moulting. Finally, there also remains the possibility that condition in this octopus species is determined genetically, as has been reported in recent studies across different taxonomical groups.

Evaluating natural resource amenities in a human life expectancy production function

Treesearch

Neelam C. Poudyal; Donald G. Hodges; J.M. Bowker; H.K. Cordell

2009-01-01

This study examined the effect of natural resource amenities on human life expectancy. Extending theexisting model of the life expectancy production function, and correcting for spatial dependence, weevaluated the determinants of life expectancy using county level data. Results indicate that after controlling

Next Generation Life Support Project: Development of Advanced Technologies for Human Exploration Missions

NASA Technical Reports Server (NTRS)

Barta, Daniel J.

2012-01-01

Next Generation Life Support (NGLS) is one of several technology development projects sponsored by the National Aeronautics and Space Administration s Game Changing Development Program. NGLS is developing life support technologies (including water recovery, and space suit life support technologies) needed for humans to live and work productively in space. NGLS has three project tasks: Variable Oxygen Regulator (VOR), Rapid Cycle Amine (RCA) swing bed, and Alternative Water Processing. The selected technologies within each of these areas are focused on increasing affordability, reliability, and vehicle self sufficiency while decreasing mass and enabling long duration exploration. The RCA and VOR tasks are directed at key technology needs for the Portable Life Support System (PLSS) for an Exploration Extravehicular Mobility Unit (EMU), with focus on prototyping and integrated testing. The focus of the Rapid Cycle Amine (RCA) swing-bed ventilation task is to provide integrated carbon dioxide removal and humidity control that can be regenerated in real time during an EVA. The Variable Oxygen Regulator technology will significantly increase the number of pressure settings available to the space suit. Current spacesuit pressure regulators are limited to only two settings while the adjustability of the advanced regulator will be nearly continuous. The Alternative Water Processor efforts will result in the development of a system capable of recycling wastewater from sources expected in future exploration missions, including hygiene and laundry water, based on natural biological processes and membrane-based post treatment. The technologies will support a capability-driven architecture for extending human presence beyond low Earth orbit to potential destinations such as the Moon, near Earth asteroids and Mars.

NREL: U.S. Life Cycle Inventory Database - Related Links

Science.gov Websites

) information, LCA tools, research institutes utilizing LCA, labeling initiatives and organizations , international LCA initiatives, LCA online forums. Life Cycle Inventory Data Ecoinvent: Swiss Centre for Life Institute for Environmental Research and Education): The American Center for Life Cycle Assessment SETAC

Optimal seasonal schedules and the relative dominance of heteromorphic and isomorphic life cycles in macroalgae.

PubMed

Bessho, Kazuhiro; Iwasa, Yoh

2010-11-21

Marine macroalgae (seaweed) show diverse life cycles. Species with a heteromorphic life cycle have a large multicellular algal body in one generation but have a very small body in the second generation of the same year. In contrast, the diploid and haploid life forms of isomorphic species have similar morphology, and these species often have more than two generations in a year. Here, we first study the optimal life cycle schedule of marine macroalgae when daily mortality changes seasonally, and then we discuss the conditions for coexistence and relative dominance of different life cycles. According to the optimal life cycle schedule, heteromorphic species tend to have a generation with a large algal body when mortality is low, and a microscopic-sized generation when mortality is high. In contrast, isomorphic species tend to mature when body size reaches a threshold value that is the same for different generations. We then examine the coexistence of the two life cycles when growth rate decreases with biomass. The model predicts that (1) at high latitudes (i.e., in strongly seasonal environments), heteromorphic species are likely to dominate over isomorphic species, and (2) species with a heteromorphic life cycle should dominate in the supratidal and upper intertidal zones where macroalgae tend to suffer high mortality, and also in the subtidal zone, where mortality is low, whereas isomorphic species are likely to be more successful when mortality is intermediate. These predictions are consistent with the observed distribution patterns of the two life cycles in macroalgae. Copyright © 2010 Elsevier Ltd. All rights reserved.

Relative importance of demographic, socioeconomic and health factors on life expectancy in low- and lower-middle-income countries.

PubMed

Mondal, Md Nazrul Islam; Shitan, Mahendran

2014-01-01

We attempted to identify the pathways by which demographic changes, socioeconomic inequalities, and availability of health factors influence life expectancy in low- and lower-middle-income countries. Data for 91 countries were obtained from United Nations agencies. The response variable was life expectancy, and the determinant factors were demographic events (total fertility rate and adolescent fertility rate), socioeconomic status (mean years of schooling and gross national income per capita), and health factors (physician density and human immunodeficiency virus [HIV] prevalence rate). Path analysis was used to determine the direct, indirect, and total effects of these factors on life expectancy. All determinant factors were significantly correlated with life expectancy. Mean years of schooling, total fertility rate, and HIV prevalence rate had significant direct and indirect effects on life expectancy. The total effect of higher physician density was to increase life expectancy. We identified several direct and indirect pathways that predict life expectancy. The findings suggest that policies should concentrate on improving reproductive decisions, increasing education, and reducing HIV transmission. In addition, special attention should be paid to the emerging need to increase life expectancy by increasing physician density.

Relative Importance of Demographic, Socioeconomic and Health Factors on Life Expectancy in Low- and Lower-Middle-Income Countries

PubMed Central

Mondal, Md. Nazrul Islam; Shitan, Mahendran

2014-01-01

Background We attempted to identify the pathways by which demographic changes, socioeconomic inequalities, and availability of health factors influence life expectancy in low- and lower-middle-income countries. Methods Data for 91 countries were obtained from United Nations agencies. The response variable was life expectancy, and the determinant factors were demographic events (total fertility rate and adolescent fertility rate), socioeconomic status (mean years of schooling and gross national income per capita), and health factors (physician density and human immunodeficiency virus [HIV] prevalence rate). Path analysis was used to determine the direct, indirect, and total effects of these factors on life expectancy. Results All determinant factors were significantly correlated with life expectancy. Mean years of schooling, total fertility rate, and HIV prevalence rate had significant direct and indirect effects on life expectancy. The total effect of higher physician density was to increase life expectancy. Conclusions We identified several direct and indirect pathways that predict life expectancy. The findings suggest that policies should concentrate on improving reproductive decisions, increasing education, and reducing HIV transmission. In addition, special attention should be paid to the emerging need to increase life expectancy by increasing physician density. PMID:24390415

[Life cycle assessment of energy consumption and greenhouse gas emissions of cellulosic ethanol from corn stover].

PubMed

Tian, Wang; Liao, Cuiping; Li, Li; Zhao, Daiqing

2011-03-01

Life Cycle Assessment (LCA) is the only standardized tool currently used to assess environmental loads of products and processes. The life cycle analysis, as a part of LCA, is a useful and powerful methodology for studying life cycle energy efficiency and life cycle GHG emission. To quantitatively explain the potential of energy saving and greenhouse gas (GHG) emissions reduction of corn stover-based ethanol, we analyzed life cycle energy consumption and GHG emissions of corn stover-based ethanol by the method of life cycle analysis. The processes are dilute acid prehydrolysis and enzymatic hydrolysis. The functional unit was defined as 1 km distance driven by the vehicle. Results indicated: compared with gasoline, the corn stover-based E100 (100% ethanol) and E10 (a blend of 10% ethanol and 90% gasoline by volume) could reduce life cycle fossil energy consumption by 79.63% and 6.25% respectively, as well as GHG emissions by 53.98% and 6.69%; the fossil energy consumed by biomass stage was 68.3% of total fossil energy input, N-fertilizer and diesel were the main factors which contributed 45.78% and 33.26% to biomass stage; electricity production process contributed 42.06% to the net GHG emissions, the improvement of technology might reduce emissions markedly.

Mortality inequality in populations with equal life expectancy: Arriaga's decomposition method in SAS, Stata, and Excel.

PubMed

Auger, Nathalie; Feuillet, Pascaline; Martel, Sylvie; Lo, Ernest; Barry, Amadou D; Harper, Sam

2014-08-01

Life expectancy is used to measure population health, but large differences in mortality can be masked even when there is no life expectancy gap. We demonstrate how Arriaga's decomposition method can be used to assess inequality in mortality between populations with near equal life expectancy. We calculated life expectancy at birth for Quebec and the rest of Canada from 2005 to 2009 using life tables and partitioned the gap between both populations into age and cause-specific components using Arriaga's method. The life expectancy gap between Quebec and Canada was negligible (<0.1 years). Decomposition of the gap showed that higher lung cancer mortality in Quebec was offset by cardiovascular mortality in the rest of Canada, resulting in identical life expectancy in both groups. Lung cancer in Quebec had a greater impact at early ages, whereas cardiovascular mortality in Canada had a greater impact at older ages. Despite the absence of a gap, we demonstrate using decomposition analyses how lung cancer at early ages lowered life expectancy in Quebec, whereas cardiovascular causes at older ages lowered life expectancy in Canada. We provide SAS/Stata code and an Excel spreadsheeet to facilitate application of Arriaga's method to other settings. Copyright © 2014 Elsevier Inc. All rights reserved.

KOH concentration effect on the cycle life of nickel-hydrogen cells

NASA Technical Reports Server (NTRS)

Lim, H. S.; Verzwyvelt, S. A.

1985-01-01

Effects of KOH concentration on the cycle life of a sintered-type nickel electrode were studied in a boiler plate nickel-hydrogen cell at 23 C using an accelerated 45-min cycle regime at 80 percent depth of discharge. The cycle life improved greatly as the KOH concentration decreased, although the initial capacity of the cell decreased slightly. The cycle life improved by a factor of two or more when the KOH concentration was reduced from 36 to 31 percent and by a similar factor from reductions of 31 to 26 percent. For many applications, this life improvement may outweigh the initial capacity decrease.

Increases in adult life expectancy in rural South Africa: valuing the scale-up of HIV treatment

PubMed Central

Bor, Jacob; Herbst, Abraham J; Newell, Marie-Louise; Bärnighausen, Till

2013-01-01

The scale-up of antiretroviral therapy (ART) is expected to raise adult life expectancy in populations with high HIV prevalence. Using data from a population cohort of over 101,000 individuals in rural KwaZulu-Natal, South Africa, we measured changes in adult life expectancy for 2000–2011. In 2003, the year before ART became available in the public sector health system, adult life expectancy was 49.2 years; by 2011, adult life expectancy had increased to 60.5 years – an 11.3-year gain. Based on standard monetary valuation of life, the survival benefits of ART far outweigh the costs of providing treatment in this community. These gains in adult life expectancy signify the social value of ART and have implications for investment decisions of individuals, governments, and donors. PMID:23430655

ANALYSIS OF TRENDS IN LIFE EXPECTANCIES AND PER CAPITA GROSS DOMESTIC PRODUCT AS WELL AS PHARMACEUTICAL AND NON-PHARMACEUTICAL HEALTHCARE EXPENDITURES.

PubMed

Hermanowski, Tomasz; Bystrov, Victor; Staszewska-Bystrova, Anna; Szafraniec-Buryło, Sylwia I; Rabczenko, Daniel; Kolasa, Katarzyna; Orlewska, Ewa

2015-01-01

Life expectancy is a common measure of population health. Macro-perspective based on aggregated data makes it possible to approximate the impact of different levels of pharmaceutical expenditure on general population health status and is often used in cross-country comparisons. The aim of the study was to determine whether there are long-run relations between life expectancy, total healthcare expenditures, and pharmaceutical expenditures in OECD countries. Common trends in per capita gross domestic products (GDPs) (excluding healthcare expenditures), per capita healthcare expenditures (excluding pharmaceutical expenditures), per capita pharmaceutical expenditures, and life expectancies of women and men aged 60 and 65 were analyzed across OECD countries. Short-term effect of pharmaceutical expenditure onto life expectancy was also estimated by regressing the deviations of life expectancies from their long-term trends onto the deviations of pharmaceutical and non-pharmaceutical health expenditures, as well as GDP from their trends. The dataset was created on the basis of OECD Health Data for 34 countries and the years 1991-2010. Life expectancy variables were used as proxies for the health outcomes, whereas the pharmaceutical and healthcare expenditures represented drug and healthcare consumption, respectively. In general, both expenditures and life expectancies tended to increase in all of the analyzed countries; however, the growth rates differed across the countries. The analysis of common trends indicated the existence of common long-term trends in life expectancies and per capita GDP as well as pharmaceutical and non-pharmaceutical healthcare expenditures. However, there was no evidence that pharmaceutical expenditures provided additional information about the long-term trends in life expectancies beyond that contained in the GDP series. The analysis based on the deviations of variables from their long-term trends allowed concluding that pharmaceutical expenditures significantly influenced life expectancies in the short run. Non-pharmaceutical healthcare expenditures were found to be significant in one out of four models (for life expectancy of women aged 65), while GDPs were found to be insignificant in all four models. The results of the study indicate that there are common long-term trends in life expectancies and per capita GDP as well as pharmaceutical and non-pharmaceutical healthcare expenditures. The available data did not reveal any cause- effect relationship. Other factors, for which the systematic data were not available, may have determined the increase in life expectancy in OECD countries. Significant positive short-term relations between pharmaceutical expenditures and life expectancies in OECD countries were found. The significant short-term effect of pharmaceutical expenditures onto life expectancy means that an increase of pharmaceutical expenditures above long-term trends would lead to a temporary increase in life expectancy above its corresponding long-term trend. However, this effect would not persist as pharmaceutical expenditures and life expectancy would converge to levels determined by the long-term trends.

Feasibility of water injection into the turbine coolant to permit gas turbine contingency power for helicopter application

NASA Technical Reports Server (NTRS)

Vanfossen, G. J.

1983-01-01

A system which would allow a substantially increased output from a turboshaft engine for brief periods in emergency situations with little or no loss of turbine stress rupture life is proposed and studied analytically. The increased engine output is obtained by overtemperaturing the turbine; however, the temperature of the compressor bleed air used for hot section cooling is lowered by injecting and evaporating water. This decrease in cooling air temperature can offset the effect of increased gas temperature and increased shaft speed and thus keep turbine blade stress rupture life constant. The analysis utilized the NASA-Navy-Engine-Program or NNEP computer code to model the turboshaft engine in both design and off-design modes. This report is concerned with the effect of the proposed method of power augmentation on the engine cycle and turbine components. A simple cycle turboshaft engine with a 16:1 pressure ratio and a 1533 K (2760 R) turbine inlet temperature operating at sea level static conditions was studied to determine the possible power increase and the effect on turbine stress rupture life that could be expected using the proposed emergency cooling scheme. The analysis showed a 54 percent increse in output power can be achieved with no loss in gas generator turbine stress rupture life. A 231 K (415 F) rise in turbine inlet temperature is required for this level of augmentation. The required water flow rate was found to be .0109 kg water per kg of engine air flow.

Effect of LEO cycling on 125 Ah advanced design IPV nickel-hydrogen flight cells - An update

NASA Technical Reports Server (NTRS)

Smithrick, John J.; Hall, Stephen W.

1991-01-01

An update of validation test results confirming the breakthrough in LEO cycle life of nickel-hydrogen cells containing 26 percent potassium hydroxide (KOH) electrolyte is presented. A breakthrough in the LEO cycle life of individual pressure vessel nickel-hydrogen cells is reported. The cycle life of boiler plate cells containing 26 percent KOH electrolyte was about 40,000 LEO cycles compared to 3500 cycles for cells containing 31 percent KOH.

The Association Between Income and Life Expectancy in the United States, 2001-2014.

PubMed

Chetty, Raj; Stepner, Michael; Abraham, Sarah; Lin, Shelby; Scuderi, Benjamin; Turner, Nicholas; Bergeron, Augustin; Cutler, David

2016-04-26

The relationship between income and life expectancy is well established but remains poorly understood. To measure the level, time trend, and geographic variability in the association between income and life expectancy and to identify factors related to small area variation. Income data for the US population were obtained from 1.4 billion deidentified tax records between 1999 and 2014. Mortality data were obtained from Social Security Administration death records. These data were used to estimate race- and ethnicity-adjusted life expectancy at 40 years of age by household income percentile, sex, and geographic area, and to evaluate factors associated with differences in life expectancy. Pretax household earnings as a measure of income. Relationship between income and life expectancy; trends in life expectancy by income group; geographic variation in life expectancy levels and trends by income group; and factors associated with differences in life expectancy across areas. The sample consisted of 1,408,287,218 person-year observations for individuals aged 40 to 76 years (mean age, 53.0 years; median household earnings among working individuals, $61,175 per year). There were 4,114,380 deaths among men (mortality rate, 596.3 per 100,000) and 2,694,808 deaths among women (mortality rate, 375.1 per 100,000). The analysis yielded 4 results. First, higher income was associated with greater longevity throughout the income distribution. The gap in life expectancy between the richest 1% and poorest 1% of individuals was 14.6 years (95% CI, 14.4 to 14.8 years) for men and 10.1 years (95% CI, 9.9 to 10.3 years) for women. Second, inequality in life expectancy increased over time. Between 2001 and 2014, life expectancy increased by 2.34 years for men and 2.91 years for women in the top 5% of the income distribution, but by only 0.32 years for men and 0.04 years for women in the bottom 5% (P < .001 for the differences for both sexes). Third, life expectancy for low-income individuals varied substantially across local areas. In the bottom income quartile, life expectancy differed by approximately 4.5 years between areas with the highest and lowest longevity. Changes in life expectancy between 2001 and 2014 ranged from gains of more than 4 years to losses of more than 2 years across areas. Fourth, geographic differences in life expectancy for individuals in the lowest income quartile were significantly correlated with health behaviors such as smoking (r = -0.69, P < .001), but were not significantly correlated with access to medical care, physical environmental factors, income inequality, or labor market conditions. Life expectancy for low-income individuals was positively correlated with the local area fraction of immigrants (r = 0.72, P < .001), fraction of college graduates (r = 0.42, P < .001), and government expenditures (r = 0.57, P < .001). In the United States between 2001 and 2014, higher income was associated with greater longevity, and differences in life expectancy across income groups increased over time. However, the association between life expectancy and income varied substantially across areas; differences in longevity across income groups decreased in some areas and increased in others. The differences in life expectancy were correlated with health behaviors and local area characteristics.

The effect of individual differences and manipulated life expectancies on the willingness to engage in sexual coercion.

PubMed

Dunkel, Curtis S; Mathes, Eugene

2011-12-16

The role of the individual difference variables of mate value, short-term and long-term mating preferences, and life history strategy along with the manipulated variable of life expectancy were used to predict differences in the willingness to engage in sexually coercive behaviors. Short-term preferences and long-term preferences were correlated with the willingness to engage in sexual coercion at all life expectancies. Life history strategy was correlated with the willingness to engage in sexual coercion at only the shortest and longest life expectancies. Most importantly short-term and long-term mating preferences interacted with life expectancy to predict the willingness to engage in sexually coercive behaviors. Short life expectancies increased willingness in individuals with high short-term and low long-term preferences. The results are discussed in terms of the varying theories of sexual coercion with emphasis put on a life history approach.

Evaluation of life-cycle air emission factors of freight transportation.

PubMed

Facanha, Cristiano; Horvath, Arpad

2007-10-15

Life-cycle air emission factors associated with road, rail, and air transportation of freight in the United States are analyzed. All life-cycle phases of vehicles, infrastructure, and fuels are accounted for in a hybrid life-cycle assessment (LCA). It includes not only fuel combustion, but also emissions from vehicle manufacturing, maintenance, and end of life, infrastructure construction, operation, maintenance, and end of life, and petroleum exploration, refining, and fuel distribution. Results indicate that total life-cycle emissions of freight transportation modes are underestimated if only tailpipe emissions are accounted for. In the case of CO2 and NOx, tailpipe emissions underestimate total emissions by up to 38%, depending on the mode. Total life-cycle emissions of CO and SO2 are up to seven times higher than tailpipe emissions. Sensitivity analysis considers the effects of vehicle type, geography, and mode efficiency on the final results. Policy implications of this analysis are also discussed. For example, while it is widely assumed that currently proposed regulations will result in substantial reductions in emissions, we find that this is true for NOx, emissions, because fuel combustion is the main cause, and to a lesser extent for SO2, but not for PM10 emissions, which are significantly affected by the other life-cycle phases.

Latitudinal variation in diapause duration and post-winter development in two pierid butterflies in relation to phenological specialization.

PubMed

Posledovich, Diana; Toftegaard, Tenna; Wiklund, Christer; Ehrlén, Johan; Gotthard, Karl

2015-01-01

Diapause plays a central role in insect life cycles by allowing survival during adverse seasonal conditions as well as synchronizing life cycles with the period of mate and food availability. Seasonal timing is expected to be particularly important for species that are dependent on resources available during a short time window-so-called phenological specialists-and latitudinal clines in seasonality are expected to favor local adaptation in phenological timing. However, to what degree latitudinal variation in diapause dynamics and post-winter development due to such local adaptation is influenced by the degree of phenological specialization is not well known. We experimentally studied two pierid butterfly species and found that the phenological specialist Anthocharis cardamines had shorter diapause duration than the phenological generalist Pieris napi along a latitudinal gradient in Sweden. Moreover, diapause duration increased with latitude in P. napi but not in A. cardamines. Sensitivity of the two species to winter thermal conditions also differed; additional cold temperature during the winter period shortened diapause duration for P. napi pupae but not for A. cardamines pupae. In both species, post-winter pupal development was faster after longer periods of cold conditions, and more southern populations developed faster than northern populations. Post-winter development was also invariably faster at higher temperatures in both species. We argue that the observed differences in diapause dynamics between the two species might be explained by the difference in phenological specialization that influences the costs of breaking diapause too early in the season.

Modeling flows and concentrations of nine engineered nanomaterials in the Danish environment.

PubMed

Gottschalk, Fadri; Lassen, Carsten; Kjoelholt, Jesper; Christensen, Frans; Nowack, Bernd

2015-05-22

Predictions of environmental concentrations of engineered nanomaterials (ENM) are needed for their environmental risk assessment. Because analytical data on ENM-concentrations in the environment are not yet available, exposure modeling represents the only source of information on ENM exposure in the environment. This work provides material flow data and environmental concentrations of nine ENM in Denmark. It represents the first study that distinguishes between photostable TiO₂ (as used in sunscreens) and photocatalytic TiO₂ (as used in self-cleaning surfaces). It also provides first exposure estimates for quantum dots, carbon black and CuCO₃. Other ENM that are covered are ZnO, Ag, CNT and CeO₂. The modeling is based for all ENM on probability distributions of production, use, environmental release and transfer between compartments, always considering the complete life-cycle of products containing the ENM. The magnitude of flows and concentrations of the various ENM depends on the one hand on the production volume but also on the type of products they are used in and the life-cycles of these products and their potential for release. The results reveal that in aquatic systems the highest concentrations are expected for carbon black and photostable TiO₂, followed by CuCO₃ (under the assumption that the use as wood preservative becomes important). In sludge-treated soil highest concentrations are expected for CeO₂ and TiO₂. Transformation during water treatments results in extremely low concentrations of ZnO and Ag in the environment. The results of this study provide valuable environmental exposure information for future risk assessments of these ENM.

An assessment of the distribution and spread of the tick Hyalomma marginatum in the western Palearctic under different climate scenarios.

PubMed

Estrada-Peña, Agustín; Sánchez, Nely; Estrada-Sánchez, Adrián

2012-09-01

We applied a process-driven model to evaluate the impact of climate scenarios for the years 2020, 2050, and 2080 on the life cycle of Hyalomma marginatum ticks in the western Palearctic. The net growth rate of the tick populations increased in every scenario tested compared to the current climate baseline. These results support the expectations of increased tick survival and increased population turnover in future climate scenarios. We included a basic evaluation of host movement based on rules connected to altitude, slope, size of the near patches, and inter-patch distances in the real landscape over the target area. Data on landscape were obtained from medium-resolution MODIS satellite imagery, which allowed us to test the potential spread of the populations. Such a model of host dispersal linked to the process-driven life cycle model demonstrated that eastern (Turkey, Russia, and Balkans) populations of H. marginatum currently are well separated and have little mixing with western (Italy, Spain, and northern Africa) populations. The northern limit is marked by the cold areas in the Balkans, Alps, and Pyrenees. Under the warmer conditions predicted by the climate scenarios, the exchange of ticks throughout new areas, previously free of the vector, is expected to increase, mainly in the Balkans and southern Russia, over the limit of the mountain ranges. Therefore, the northern limit of the tick range would increase. Additional studies are necessary to understand the implications of host changes in range and abundance for H. marginatum and Crimean-Congo hemorrhagic fever virus.

Optical Measurements for Intelligent Aerospace Propulsion

NASA Technical Reports Server (NTRS)

Mercer, Carolyn R.

2003-01-01

There is growing interest in applying intelligent technologies to aerospace propulsion systems to reap expected benefits in cost, performance, and environmental compliance. Cost benefits span the engine life cycle from development, operations, and maintenance. Performance gains are anticipated in reduced fuel consumption, increased thrust-toweight ratios, and operability. Environmental benefits include generating fewer pollutants and less noise. Critical enabling technologies to realize these potential benefits include sensors, actuators, logic, electronics, materials, and structures. For propulsion applications, the challenge is to increase the robustness of these technologies so that they can withstand harsh temperatures, vibrations, and grime while providing extremely reliable performance. This paper addresses the role that optical metrology is playing in providing solutions to these challenges. Optics for ground-based testing (development cycle), flight sensing (operations), and inspection (maintenance) are described. Opportunities for future work are presented.

Comparative Life Cycle Assessment between Warm SMA and Conventional SMA

DOT National Transportation Integrated Search

2011-09-01

This report presents the comparative life cycle assessment (LCA) between warm stone mastic asphalt (SMA) and conventional : SMA. Specifically, the study evaluated and compared the life cycle environmental and economic performances of two mixtures: a ...

Geothermal Water Use: Life Cycle Water Consumption, Water Resource Assessment, and Water Policy Framework

DOE Data Explorer

Schroeder, Jenna N.

2014-06-10

This report examines life cycle water consumption for various geothermal technologies to better understand factors that affect water consumption across the life cycle (e.g., power plant cooling, belowground fluid losses) and to assess the potential water challenges that future geothermal power generation projects may face. Previous reports in this series quantified the life cycle freshwater requirements of geothermal power-generating systems, explored operational and environmental concerns related to the geochemical composition of geothermal fluids, and assessed future water demand by geothermal power plants according to growth projections for the industry. This report seeks to extend those analyses by including EGS flash, both as part of the life cycle analysis and water resource assessment. A regional water resource assessment based upon the life cycle results is also presented. Finally, the legal framework of water with respect to geothermal resources in the states with active geothermal development is also analyzed.

Long Life Nickel Electrodes for a Nickel-hydrogen Cell: Cycle Life Tests

NASA Technical Reports Server (NTRS)

Lim, H. S.; Verzwyvelt, S. A.

1984-01-01

In order to develop a long life nickel electrode for a Ni/H2 cell, cycle life tests of nickel electrodes were carried out in Hi/H2 boiler plate cells. A 19 test cell matrix was made of various nickel electrode designs including three levels each of plaque mechanical strength, median pore size of the plaque, and active material loading. Test cells were cycled to the end of their life (0.5v) in a 45-minute low earth orbit cycle regime at 80% depth-of-discharge. The results show that the active material loading level affects the cycle life the most with the optimum loading at 1.6 g/cc void. Mechanical strength did not affect the cycle life noticeably in the bend strength range of 400 to 700 psi. The best plaque type appears to be one which is made of INCO nickel powder type 287 and has a median pore size of 13 micron.

Fitness and Individuality in Complex Life Cycles.

PubMed

Herron, Matthew D

2016-12-01

Complex life cycles are common in the eukaryotic world, and they complicate the question of how to define individuality. Using a bottom-up, gene-centric approach, I consider the concept of fitness in the context of complex life cycles. I analyze the fitness effects of an allele (or a trait) on different biological units within a complex life history and how these effects drive evolutionary change within populations. Based on these effects, I attempt to construct a concept of fitness that accurately predicts evolutionary change in the context of complex life cycles.

Using Survival Analysis to Improve Estimates of Life Year Gains in Policy Evaluations.

PubMed

Meacock, Rachel; Sutton, Matt; Kristensen, Søren Rud; Harrison, Mark

2017-05-01

Policy evaluations taking a lifetime horizon have converted estimated changes in short-term mortality to expected life year gains using general population life expectancy. However, the life expectancy of the affected patients may differ from the general population. In trials, survival models are commonly used to extrapolate life year gains. The objective was to demonstrate the feasibility and materiality of using parametric survival models to extrapolate future survival in health care policy evaluations. We used our previous cost-effectiveness analysis of a pay-for-performance program as a motivating example. We first used the cohort of patients admitted prior to the program to compare 3 methods for estimating remaining life expectancy. We then used a difference-in-differences framework to estimate the life year gains associated with the program using general population life expectancy and survival models. Patient-level data from Hospital Episode Statistics was utilized for patients admitted to hospitals in England for pneumonia between 1 April 2007 and 31 March 2008 and between 1 April 2009 and 31 March 2010, and linked to death records for the period from 1 April 2007 to 31 March 2011. In our cohort of patients, using parametric survival models rather than general population life expectancy figures reduced the estimated mean life years remaining by 30% (9.19 v. 13.15 years, respectively). However, the estimated mean life year gains associated with the program are larger using survival models (0.380 years) compared to using general population life expectancy (0.154 years). Using general population life expectancy to estimate the impact of health care policies can overestimate life expectancy but underestimate the impact of policies on life year gains. Using a longer follow-up period improved the accuracy of estimated survival and program impact considerably.

On the decomposition of life expectancy and limits to life.

PubMed

Mayhew, Les; Smith, David

2015-01-01

Life expectancy is a measure of how long people are expected to live and is widely used as a measure of human development. Variations in the measure reflect not only the process of ageing but also the impacts of such events as epidemics, wars, and economic recessions. Since 1950, the influence of these events in the most developed countries has waned and life expectancy continues to lengthen unabated. As a result, it has become more difficult to forecast long-run trends accurately, or identify possible upper limits. We present new methods for comparing past improvements in life expectancy and also future prospects, using data from five developed, low-mortality countries. We consider life expectancy in 10-year age intervals rather than over the remaining lifetime, and show how natural limits to life expectancy can be used to extrapolate trends. We discuss the implications and compare our approach with other commonly used methods.

A comparative study of commercial lithium ion battery cycle life in electric vehicle: Capacity loss estimation

NASA Astrophysics Data System (ADS)

Han, Xuebing; Ouyang, Minggao; Lu, Languang; Li, Jianqiu

2014-12-01

Now the lithium ion batteries are widely used in electric vehicles (EV). The cycle life is among the most important characteristics of the power battery in EV. In this report, the battery cycle life experiment is designed according to the actual working condition in EV. Five different commercial lithium ion cells are cycled alternatively under 45 °C and 5 °C and the test results are compared. Based on the cycle life experiment results and the identified battery aging mechanism, the battery cycle life models are built and fitted by the genetic algorithm. The capacity loss follows a power law relation with the cycle times and an Arrhenius law relation with the temperature. For automotive application, to save the cost and the testing time, a battery SOH (state of health) estimation method combined the on-line model based capacity estimation and regular calibration is proposed.

A Growth Model for Academic Program Life Cycle (APLC): A Theoretical and Empirical Analysis

ERIC Educational Resources Information Center

Acquah, Edward H. K.

2010-01-01

Academic program life cycle concept states each program's life flows through several stages: introduction, growth, maturity, and decline. A mixed-influence diffusion growth model is fitted to enrolment data on academic programs to analyze the factors determining progress of academic programs through their life cycles. The regression analysis yield…

Evaluating natural resource amenities in a human life expectancy production function

Treesearch

Neelam C. Poudyal; Donald G. Hodges; J.M. Bowker; H.K. Cordell

2009-01-01

This study examined the effect of natural resource amenities on human life expectancy. Extending the existing model of the life expectancy production function, and correcting for spatial dependence, we evaluated the determinants of life expectancy using county level data. Results indicate that after controlling for socio-demographic and economic factors, medical...

Subjective Life Expectancy Among College Students.

PubMed

Rodemann, Alyssa E; Arigo, Danielle

2017-09-14

Establishing healthy habits in college is important for long-term health. Despite existing health promotion efforts, many college students fail to meet recommendations for behaviors such as healthy eating and exercise, which may be due to low perceived risk for health problems. The goals of this study were to examine: (1) the accuracy of life expectancy predictions, (2) potential individual differences in accuracy (i.e., gender and conscientiousness), and (3) potential change in accuracy after inducing awareness of current health behaviors. College students from a small northeastern university completed an electronic survey, including demographics, initial predictions of their life expectancy, and their recent health behaviors. At the end of the survey, participants were asked to predict their life expectancy a second time. Their health data were then submitted to a validated online algorithm to generate calculated life expectancy. Participants significantly overestimated their initial life expectancy, and neither gender nor conscientiousness was related to the accuracy of these predictions. Further, subjective life expectancy decreased from initial to final predictions. These findings suggest that life expectancy perceptions present a unique-and potentially modifiable-psychological process that could influence college students' self-care.

A Life Cycle Cost Analysis of Rigid Pavements

DOT National Transportation Integrated Search

1999-09-01

The Texas Department of Transportation (TxDOT)commissioned a research project in 1996, summarized here, to promote life cycle cost analysis of rigid pavements throughout the TxDOT districts by developing a uniform methodology for performing life cycl...

Intersection life cycle cost comparison tool user guide version 1.0.

DOT National Transportation Integrated Search

2016-05-01

The Intersection Life Cycle Cost Comparison Tool User Guide was developed as part of North : Carolina Department of Transportation Research Project No. 201411: Evaluation of Life Cycle : Impacts of Intersection Control Type Selection. : This sprea...

Life Cycle Impact Assessment Research Developments and Needs

EPA Science Inventory

Life Cycle Impact Assessment (LCIA) developments are explained along with key publications which record discussions which comprised ISO 14042 and SETAC document development, UNEP SETAC Life Cycle Initiative research, and research from public and private research institutions. It ...

Increased Life Expectancy in New York City, 2001-2010: An Exploration by Cause of Death and Demographic Characteristics.

PubMed

Li, Wenhui; Maduro, Gil A; Begier, Elizabeth M

2016-01-01

New York City's (NYC's) life expectancy gains have been greater than those seen nationally. We examined life-expectancy changes over the past decade in selected NYC subpopulations and explored which age groups and causes of death contributed most to the increases. We calculated life expectancy with 95% confidence intervals (CIs) for 2001-2010 by sex and race/ethnicity. Life expectancy was decomposed by age group and cause of death. Logistic regressions were conducted to reinforce the results from decomposition by controlling confounders. Overall, NYC residents' life expectancy at birth increased from 77.9 years (95% CI, 77.8-78.0) in 2001 to 80.9 years (95% CI, 80.8-81.0) in 2010. Decreases in deaths from heart disease, cancer, and HIV disease accounted for 50%, 16%, and 11%, respectively, of the gains. Decreased mortality in older age groups (≥65 years) accounted for 45.6% of the overall change. Life expectancy increased for both sexes, across all racial/ethnic groups, and for both the US-born and the foreign-born. Disparities in life expectancy decreased as overall life expectancy increased. Decreased mortality among older adults and from heart disease, cancer, and HIV infection accounted for most of the increases.

Life expectancy--a commentary on this life table variable.

PubMed

Singer, Richard B

2005-01-01

In 1992, I wrote an article on a method of modifying the Decennial US Life Table to accommodate any pattern of excess mortality expressed in terms of excess death rate (EDR), for the specific purpose of calculating the reduced life expectancy, e. I believe this was the first article published in the Journal of Insurance Medicine (JIM) that dealt specifically with life expectancy as an index of survival and risk appraisal, never used in the classification of extra mortality risk in applicants for life insurance. In this commentary, I discuss the 1989-91 US Decennial Life Table in detail. I link the subject matter of the 1992 article with several more recent articles that also focus on the utility of life expectancy in underwriting structured settlement annuities and preparing reports on life expectancy for an attorney in a tort case. A few references are given for further reading on life table methodology and its use in the most accurate estimate of life expectancy, given the inherent limitations of the life table and the limited duration of follow-up studies.

How often does deliberate self-harm occur relative to each suicide? A study of variations by gender and age.

PubMed

Hawton, Keith; Harriss, Louise

2008-12-01

Deliberate self-harm (DSH; i.e., nonfatal self-poisoning or self-injury) occurs much more frequently than suicide, yet there has been little detailed investigation of the comparative rates of DSH and suicide. We conducted a study of how rates of DSH relate to suicide rates across the life cycle by gender and by method of estimation of DSH rates, using 10 years of data from a local system for monitoring DSH presentations to a general hospital and national and local suicide statistics. The rate-ratio of DSH to suicide was 36 (95% CI 34.9-37.1) based on annual person-based rates of DSH episodes and was nearly five times higher in females (87.9; 95% CI 84.4-91.6) than in males (18.7; 95% CI 17.9-19.6). The ratio varied markedly across the life cycle, decreasing from more than 200 in teenagers to less than 10 in persons aged 60 years and over. The difference in the ratio between females and males also decreased over the life cycle. There were very similar findings when local suicide rates were used. These patterns were replicated when the data were analyzed, first, on the basis of all episodes of DSH during the study period, but with expectedly larger DSH:suicide ratios (e.g., overall 52.7; 95% CI 51.4-54.1), and second, on the basis of individual persons only engaging in DSH during the study period, but with smaller ratios (e.g., overall 26.2; 95% CI 25.4-27.2). The DSH:suicide rate ratios for those with high and low suicidal intent were similar within age groups except for those aged 60 years and over, in whom there was a greater proportion of high intent acts. These findings illustrate how the nature of self-harming behavior may vary in intention across the life cycle and between the genders, and provide a basis for further comparative work of this kind.

Educational differences in life expectancy over five decades among the oldest old in Norway.

PubMed

Kinge, Jonas Minet; Steingrímsdóttir, Ólöf Anna; Moe, Joakim Oliu; Skirbekk, Vegard; Næss, Øyvind; Strand, Bjørn Heine

2015-11-01

Socioeconomic inequalities in life expectancy have been shown among the middle aged and the youngest of the old individuals, but the situation in the oldest old is less clear. The aim of this study was to investigate trends in life expectancy at ages 85, 90 and 95 years by education in Norway in the period 1961-2009. This was a register-based population study including all residents in Norway aged 85 and over. Individual-level data were provided by the Central Population Register and the National Education Database. For each decade during 1961-2009, death rates by 1-year age groups were calculated separately for each sex and three educational categories. Annual life tables were used to calculate life expectancy at ages 85 (e85), 90 (e90) and 95 (e95). Educational differentials in life expectancy at each age were non-significant in the early decades, but became significant over time. For example, for the decade 2000-9, a man aged 90 years with primary education had a life expectancy of 3.4 years, while a man with tertiary education could expect to live for 3.8 years. Similar numbers in women were 4.1 and 4.5 years, respectively. Even among 95-year-old men, statistically significant differences in life expectancy were found by education in the two last decades. Education matters regarding remaining life expectancy also for the oldest old in Norway. Life expectancy at these ages is low, so a growth of 0.5 years in the life expectancy differential is sizeable. © The Author 2015. Published by Oxford University Press on behalf of the British Geriatrics Society. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Treating Chronically Ill Diabetic Patients with Limited Life Expectancy: Implications for Performance Measurement

PubMed Central

Woodard, LeChauncy D.; Landrum, Cassie R.; Urech, Tracy H.; Profit, Jochen; Virani, Salim S.; Petersen, Laura A.

2012-01-01

Background/Objectives To validly assess quality-of-care differences among providers, performance measurement programs must reliably identify and exclude patients for whom the quality indicator may not be desirable, including those with limited life expectancy. We developed an algorithm to identify patients with limited life expectancy and examined the impact of limited life expectancy on glycemic control and treatment intensification among diabetic patients. Design We identified diabetic patients with coexisting congestive heart failure, chronic obstructive pulmonary disease, dementia, end-stage liver disease, and/or primary/metastatic cancers with limited life expectancy. To validate our algorithm, we assessed 5-year mortality among patients identified as having limited life expectancy. We compared rates of meeting performance measures for glycemic control between patients with and without limited life expectancy. Among uncontrolled patients, we examined the impact of limited life expectancy on treatment intensification within 90 days. Setting 110 Veterans Administration facilities; October 2006 – September 2007 Participants 888,628 diabetic patients Measurements Hemoglobin A1c (HbA1c) <9%; treatment intensification within 90 days Results 29,016 (3%) patients had limited life expectancy. Adjusting for age, 5-year mortality was 5 times higher among patients with limited life expectancy than those without. Patients with limited life expectancy had poorer glycemic control (77.1% vs. 78.1%) and less frequent treatment intensification (20.9% vs. 28.6%) than patients without, even after controlling for patient-level characteristics (odds ratio [OR]=0.84; 95% confidence interval [CI]=0.81-0.86 and OR=0.71; 95% CI=0.67-0.76, respectively). Conclusion Patients with limited life expectancy were slightly, but significantly less likely than those without to have HbA1c levels controlled and to receive treatment intensification, suggesting that providers treat these patients less aggressively. Quality measurement and performance-based reimbursement systems should acknowledge the different needs of this population. PMID:22260627

Lys48 ubiquitination during the intraerythrocytic cycle of the rodent malaria parasite, Plasmodium chabaudi.

PubMed

González-López, Lorena; Carballar-Lejarazú, Rebeca; Arrevillaga Boni, Gerardo; Cortés-Martínez, Leticia; Cázares-Raga, Febe Elena; Trujillo-Ocampo, Abel; Rodríguez, Mario H; James, Anthony A; Hernández-Hernández, Fidel de la Cruz

2017-01-01

Ubiquitination tags proteins for different functions within the cell. One of the most abundant and studied ubiquitin modification is the Lys48 polyubiquitin chain that modifies proteins for their destruction by proteasome. In Plasmodium is proposed that post-translational regulation is fundamental for parasite development during its complex life-cycle; thus, the objective of this work was to analyze the ubiquitination during Plasmodium chabaudi intraerythrocytic stages. Ubiquitinated proteins were detected during intraerythrocytic stages of Plasmodium chabaudi by immunofluorescent microscopy, bidimensional electrophoresis (2-DE) combined with immunoblotting and mass spectrometry. All the studied stages presented protein ubiquitination and Lys48 polyubiquitination with more abundance during the schizont stage. Three ubiquitinated proteins were identified for rings, five for trophozoites and twenty for schizonts. Only proteins detected with a specific anti- Lys48 polyubiquitin antibody were selected for Mass Spectrometry analysis and two of these identified proteins were selected in order to detect the specific amino acid residues where ubiquitin is placed. Ubiquitinated proteins during the ring and trophozoite stages were related with the invasion process and in schizont proteins were related with nucleic acid metabolism, glycolysis and protein biosynthesis. Most of the ubiquitin detection was during the schizont stage and the Lys48 polyubiquitination during this stage was related to proteins that are expected to be abundant during the trophozoite stage. The evidence that these Lys48 polyubiquitinated proteins are tagged for destruction by the proteasome complex suggests that this type of post-translational modification is important in the regulation of protein abundance during the life-cycle and may also contribute to the parasite cell-cycle progression.

Application of Pharmacokinetics and Pharmacodynamics in Product Life Cycle Management. A Case Study with a Carbidopa-Levodopa Extended-Release Formulation.

PubMed

Modi, Nishit B

2017-05-01

Increasing costs in discovering and developing new molecular entities and the continuing debate on limited company pipelines mean that pharmaceutical companies are under significant pressure to maximize the value of approved products. Life cycle management in the context of drug development comprises activities to maximize the effective life of a product. Life cycle approaches can involve new formulations, new routes of delivery, new indications or expansion of the population for whom the product is indicated, or development of combination products. Life cycle management may provide an opportunity to improve upon the current product through enhanced efficacy or reduced side effects and could expand the therapeutic market for the product. Successful life cycle management may include the potential for superior efficacy, improved tolerability, or a better prescriber or patient acceptance. Unlike generic products where bioequivalence to an innovator product may be sufficient for drug approval, life cycle management typically requires a series of studies to characterize the value of the product. This review summarizes key considerations in identifying product candidates that may be suitable for life cycle management and discusses the application of pharmacokinetics and pharmacodynamics in developing new products using a life cycle management approach. Examples and a case study to illustrate how pharmacokinetics and pharmacodynamics contributed to the selection of dosing regimens, demonstration of an improved therapeutic effect, or regulatory approval of an improved product label are presented.

Building Maintenance and Repair Data for Life-Cycle Cost Analyses: Electrical Systems.

DTIC Science & Technology

1991-05-01

Repair Data for Life-Cycle Cost Analyses: Electrical Systems by Edgar S. Neely Robert D. Neathammer James R. Stirn Robert P. Winkler This research...systems have been developed to assist planners in preparing DD Form 1391 documentation, designers in life-cycle cost component selection, and maintainers...Maintenance and Repair Data for Life-Cycle Cost Analyses: RDTE dated 1980 Electrical Systems REIMB 1984 - 1989 6. AUTH4OR(S) Edgar S. Neely, Robert D

Why Army Program Managers Struggle As Life Cycle Managers: A Study of the PM’s Roles, Responsibilities, and Barriers In the Execution of Operations and Support

DTIC Science & Technology

2016-09-01

Support Strategies (PBPSS), throughout the system life cycle .  Maximizing competition, to include small business participation.  Developing...NAVAL POSTGRADUATE SCHOOL MONTEREY, CALIFORNIA JOINT APPLIED PROJECT WHY ARMY PROGRAM MANAGERS STRUGGLE AS LIFE CYCLE MANAGERS...SUBTITLE WHY ARMY PROGRAM MANAGERS STRUGGLE AS LIFE CYCLE MANAGERS: A STUDY OF THE PM’S ROLES, RESPONSIBILITIES, AND BARRIERS IN THE EXECUTION OF

How much of the difference in life expectancy between Scottish cities does deprivation explain?

PubMed

Seaman, R; Mitchell, R; Dundas, R; Leyland, A H; Popham, F

2015-10-16

Glasgow's low life expectancy and high levels of deprivation are well documented. Studies comparing Glasgow to similarly deprived cities in England suggest an excess of deaths in Glasgow that cannot be accounted for by deprivation. Within Scotland comparisons are more equivocal suggesting deprivation could explain Glasgow's excess mortality. Few studies have used life expectancy, an intuitive measure that quantifies the between-city difference in years. This study aimed to use the most up-to-date data to compare Glasgow to other Scottish cities and to (i) evaluate whether deprivation could account for lower life expectancy in Glasgow and (ii) explore whether the age distribution of mortality in Glasgow could explain its lower life expectancy. Sex specific life expectancy was calculated for 2007-2011 for the population in Glasgow and the combined population of Aberdeen, Dundee and Edinburgh. Life expectancy was calculated for deciles of income deprivation, based on the national ranking of datazones, using the Scottish Index of Multiple Deprivation. Life expectancy in Glasgow overall, and by deprivation decile, was compared to that in Aberdeen, Dundee and Edinburgh combined, and the life expectancy difference decomposed by age using Arriaga's discrete method. Life expectancy for the whole Glasgow population was lower than the population of Aberdeen, Dundee and Edinburgh combined. When life expectancy was compared by national income deprivation decile, Glasgow's life expectancy was not systematically lower, and deprivation accounted for over 90 % of the difference. This was reduced to 70 % of the difference when carrying out sensitivity analysis using city-specific income deprivation deciles. In both analyses life expectancy was not systematically lower in Glasgow when stratified by deprivation. Decomposing the differences in life expectancy also showed that the age distribution of mortality was not systematically different in Glasgow after accounting for deprivation. Life expectancy is not systematically lower across the Glasgow population compared to Aberdeen, Dundee and Edinburgh combined, once deprivation is accounted for. This provides further evidence that tackling deprivation in Glasgow would probably reduce the health inequalities that exist between Scottish cities. The change in the amount of unexplained difference when carrying out sensitivity analysis demonstrates the difficulties in comparing socioeconomic deprivation between populations, even within the same country and when applying an established ecological measure. Although the majority of health inequality between Glasgow and other Scottish cities is explained by deprivation, the difference in the amount of unexplained inequality depending on the relative context of deprivation used demonstrates the challenges associated with attributing mortality inequalities to an independent 'place effect'.

Left behind: widening disparities for males and females in US county life expectancy, 1985–2010

PubMed Central

2013-01-01

Background The United States spends more than any other country on health care. The poor relative performance of the US compared to other high-income countries has attracted attention and raised questions about the performance of the US health system. An important dimension to poor national performance is the large disparities in life expectancy. Methods We applied a mixed effects Poisson statistical model and Gaussian Process Regression to estimate age-specific mortality rates for US counties from 1985 to 2010. We generated uncertainty distributions for life expectancy at each age using standard simulation methods. Results Female life expectancy in the United States increased from 78.0 years in 1985 to 80.9 years in 2010, while male life expectancy increased from 71.0 years in 1985 to 76.3 years in 2010. The gap between female and male life expectancy in the United States was 7.0 years in 1985, narrowing to 4.6 years in 2010. For males at the county level, the highest life expectancy steadily increased from 75.5 in 1985 to 81.7 in 2010, while the lowest life expectancy remained under 65. For females at the county level, the highest life expectancy increased from 81.1 to 85.0, and the lowest life expectancy remained around 73. For male life expectancy at the county level, there have been three phases in the evolution of inequality: a period of rising inequality from 1985 to 1993, a period of stable inequality from 1993 to 2002, and rising inequality from 2002 to 2010. For females, in contrast, inequality has steadily increased during the 25-year period. Compared to only 154 counties where male life expectancy remained stagnant or declined, 1,405 out of 3,143 counties (45%) have seen no significant change or a significant decline in female life expectancy from 1985 to 2010. In all time periods, the lowest county-level life expectancies are seen in the South, the Mississippi basin, West Virginia, Kentucky, and selected counties with large Native American populations. Conclusions The reduction in the number of counties where female life expectancy at birth is declining in the most recent period is welcome news. However, the widening disparities between counties and the slow rate of increase compared to other countries should be viewed as a call for action. An increased focus on factors affecting health outcomes, morbidity, and mortality such as socioeconomic factors, difficulty of access to and poor quality of health care, and behavioral, environmental, and metabolic risk factors is urgently required. PMID:23842281

Evolutionary lability of a complex life cycle in the aphid genus Brachycaudus.

PubMed

Emmanuelle, Jousselin; Gwenaelle, Genson; Armelle, Coeur d'acier

2010-09-28

Most aphid species complete their life cycle on the same set of host-plant species, but some (heteroecious species) alternate between different hosts, migrating from primary (woody) to secondary (herbaceous) host plants. The evolutionary processes behind the evolution of this complex life cycle have often been debated. One widely accepted scenario is that heteroecy evolved from monoecy on woody host plants. Several shifts towards monoecy on herbaceous plants have subsequently occurred and resulted in the radiation of aphids. Host alternation would have persisted in some cases due to developmental constraints preventing aphids from shifting their entire life cycle to herbaceous hosts (which are thought to be more favourable). According to this scenario, if aphids lose their primary host during evolution they should not regain it. The genus Brachycaudus includes species with all the types of life cycle (monoecy on woody plants, heteroecy, monoecy on herbs). We used this genus to test hypotheses concerning the evolution of life cycles in aphids. Phylogenetic investigation and character reconstruction suggest that life cycle is evolutionary labile in the genus. Though ancestral character states can be ambiguous depending on optimization methods, all analyses suggest that transitions from monoecy on herbs towards heteroecy have occurred several times. Transitions from heteroecy towards monoecy, are also likely. There have been many shifts in feeding behaviour but we found no significant correlation between life cycle changes and changes in diet. The transitions from monoecy on herbs towards heteroecy observed in this study go against a widely accepted evolutionary scenario: aphids in the genus Brachycaudus seem to be able to recapture their supposedly ancestral woody host. This suggests that the determinants of host alternation are probably not as complicated as previously thought. Definitive proofs of the lability of life cycle in Brachycaudus will necessitate investigation of these determinants. Life cycle changes, whether corresponding to the loss or acquisition of a primary host, necessarily promote speciation, by inducing shifts of the reproductive phase on different plants. We suggest that the evolutionary lability of life cycle may have driven speciation events in the Brachycaudus genus.

Decennial trends and inequalities in healthy life expectancy: The HUNT Study, Norway.

PubMed

Storeng, Siri H; Krokstad, Steinar; Westin, Steinar; Sund, Erik R

2018-02-01

Norway is experiencing a rising life expectancy combined with an increasing dependency ratio - the ratio of those outside over those within the working force. To provide data relevant for future health policy we wanted to study trends in total and healthy life expectancy in a Norwegian population over three decades (1980s, 1990s and 2000s), both overall and across gender and educational groups. Data were obtained from the HUNT Study, and the Norwegian Educational Database. We calculated total life expectancy and used the Sullivan method to calculate healthy life expectancies based on self-rated health and self-reported longstanding limiting illness. The change in health expectancies was decomposed into mortality and disability effects. During three consecutive decades we found an increase in life expectancy for 30-year-olds (~7 years) and expected lifetime in self-rated good health (~6 years), but time without longstanding limiting illness increased less (1.5 years). Women could expect to live longer than men, but the extra life years for females were spent in poor self-rated health and with longstanding limiting illness. Differences in total life expectancy between educational groups decreased, whereas differences in expected lifetime in self-rated good health and lifetime without longstanding limiting illness increased. The increase in total life expectancy was accompanied by an increasing number of years spent in good self-rated health but more years with longstanding limiting illness. This suggests increasing health care needs for people with chronic diseases, given an increasing number of elderly. Socioeconomic health inequalities remain a challenge for increasing pensioning age.

The Association Between Income and Life Expectancy in the United States, 2001–2014

PubMed Central

Chetty, Raj; Stepner, Michael; Abraham, Sarah; Lin, Shelby; Scuderi, Benjamin; Turner, Nicholas; Bergeron, Augustin; Cutler, David

2016-01-01

Importance The relationship between income and mortality is well established but remains poorly understood. Objectives To measure the level, temporal trend, and geographic variability in the association between income and life expectancy, and identify factors related to small area variation in this association. Design and Setting Income data for the US population were obtained from 1.4 billion de-identified tax records between 1999 and 2014. Mortality data were obtained from Social Security Administration death records. These data were used to estimate race- and ethnicity-adjusted life expectancy at 40 years of age by household income percentile, sex, and geographic area, and to evaluate factors associated with differences in life expectancy. Main Outcomes and Measures Relationship between income and life expectancy; trends in life expectancy by income group; geographic variation in life expectancy levels and trends by income group; and factors associated with differences in life expectancy across areas. Results The sample consisted of 1 408 287 218 person-year observations (mean age at which individuals were analyzed, 53.0 years; median household earnings among working individuals, $61 175 per year [mean, $97 725 per year]). Among those aged 40 to 76 years, there were 4 114 380 deaths among men (mortality rate, 596.3 per 100 000) and 2 694 808 deaths among women (mortality rate, 375.1 per 100 000). The analysis yielded four results. First, higher income was associated with greater longevity throughout the income distribution. The gap in life expectancy between the richest 1% and poorest 1% of individuals was 14.6 years (95% CI, 14.4 to 14.8 years) for men and 10.1 years (95% CI, 9.9 to 10.3 years) for women. Second, inequality in life expectancy increased over time. Between 2001 and 2014, life expectancy increased by 2.34 years for men and 2.91 years for women in the top 5% of the income distribution, but increased by only 0.32 years for men and 0.04 years for women in the bottom 5% (P < .001 for the difference for both sexes). Third, life expectancy varied substantially across local areas. For individuals in the bottom income quartile, life expectancy differed by approximately 4.5 years between areas with the highest and lowest longevity. Changes in life expectancy between 2001 and 2014 ranged from gains of more than 4 years to losses of more than 2 years across areas. Fourth, geographic differences in life expectancy for individuals in the lowest income quartile were significantly correlated with health behaviors such as smoking (r = −0.69, P < .001), but were not significantly correlated with access to medical care, physical environmental factors, income inequality, or labor market conditions. Life expectancy for low income individuals was positively correlated with the local area fraction of immigrants (r = 0.72, P < .001), fraction of college graduates (r = 0.42, P < .001), and local government expenditures (r = 0.57, P < .001). Conclusions and Relevance In the United States between 2001 and 2014, higher income was associated with greater longevity, and differences in life expectancy across income groups increased. However, the association between life expectancy and income varied substantially across areas; differences in longevity across income groups decreased in some areas and increased in others. The differences in life expectancy were correlated with health behaviors and local area characteristics. PMID:27063997

5 CFR 930.301 - Information systems security awareness training program.

Code of Federal Regulations, 2012 CFR

2012-01-01

... training in system/application life cycle management, risk management, and contingency planning. (4) Chief... security management, system/application life cycle management, risk management, and contingency planning... management; and management and implementation level training in system/application life cycle management...

Life Cycle Assessment for Biofuels

EPA Science Inventory

A presentation based on life cycle assessment (LCA) for biofuels is given. The presentation focuses on energy and biofuels, interesting environmental aspects of biofuels, and how to do a life cycle assessment with some examples related to biofuel systems. The stages of a (biofuel...

Data Base Development of Automobile and Light Truck Maintenance : Volume II. Appendix E.

DOT National Transportation Integrated Search

1978-08-01

The document contains the scheduled maintenance data sheets and total cost summaries--both scheduled and unscheduled maintenance (Life cycle cost for Dealers, life cycle cost for Service Stations, life cycle cost for Independent Repair, and scheduled...

Data Base Development of Automobile and Light Truck Maintenance : Volume III. Appendix F.

DOT National Transportation Integrated Search

1978-08-01

The document contains the scheduled maintenance data sheets and total cost summaries--both scheduled and unscheduled maintenance (Life cycle cost for Dealers, life cycle cost for Service Stations, life cycle cost for Independent Repair, and scheduled...

LIFE CYCLE ASSESSMENT: PRINCIPLES AND PRACTICE

EPA Science Inventory

The following document provides an introductory overview of Life Cycle Assessment (LCA) and describes the general uses and major components of LCA. This document is an update and merger of two previous EPA documents on LCA ("Life Cycle Assessment: Inventory Guidelines and Princip...

Does the terrestrial phenology concept apply in water?

NASA Astrophysics Data System (ADS)

Winder, M.; Cloern, J. E.

2009-12-01

Terrestrial plants have a life history that has evolved to a circannual rhythm in concert with the seasonal climate system and overall biomass follows a regular cycle of growth and senescence having a period of 1 year. Consistency in phase and amplitude render terrestrial plant activity an effective tool to observe shifts in the seasonal life cycle in response to climate change. The other half of Earth’s primary production occurs in aquatic systems, dominated by unicellular algae having the capacity to divide daily under optimal conditions and population changes can, in principle, occur any time within a year. Given that periods of life cycles differ on land compared to aquatic systems, it can be expected that patterns of seasonal variability might differ between terrestrial and pelagic plants. We compiled 121 phytoplankton biomass time series with a median length of 16 years from estuarine-coastal and lake ecosystems in the temperate and subtropical zone and address three questions: Do aquatic pelagic plants follow the canonical seasonal pattern of terrestrial plants? What are the dominant periodicities of aquatic primary producers? How recurrent are cyclical patterns from year to year? We applied wavelet analysis to extract the phase and amplitude of these long-term phytoplankton time series. The data revealed that in about 45 % of the aquatic sites an annual cycle of 12-month periodicity was strongest expressed, corresponding to one peak per year. In about 20 % the 6-month periodicity dominated, characteristic of two peaks within a year, and about 35 % showed a pattern best attributed to the 2-5 month band periodicity and for 2 % no consistent periodicity emerged. The reoccurrence of the seasonal fluctuations varied however greatly from year to year, ranging from more predictable patterns to irregular patterns in other sites. These findings suggest that seasonal activity of chlorophyll a can be unpredictable and variable. We propose drivers that give rise to the broad pattern of seasonal phytoplankton fluctuations and discuss advantages and limitations of using phytoplankton phenology as indicators of climate change.

Requirements for future automotive batteries - a snapshot

NASA Astrophysics Data System (ADS)

Karden, Eckhard; Shinn, Paul; Bostock, Paul; Cunningham, James; Schoultz, Evan; Kok, Daniel

Introduction of new fuel economy, performance, safety, and comfort features in future automobiles will bring up many new, power-hungry electrical systems. As a consequence, demands on automotive batteries will grow substantially, e.g. regarding reliability, energy throughput (shallow-cycle life), charge acceptance, and high-rate partial state-of-charge (HRPSOC) operation. As higher voltage levels are mostly not an economically feasible alternative for the short term, the existing 14 V electrical system will have to fulfil these new demands, utilizing advanced 12 V energy storage devices. The well-established lead-acid battery technology is expected to keep playing a key role in this application. Compared to traditional starting-lighting-ignition (SLI) batteries, significant technological progress has been achieved or can be expected, which improve both performance and service life. System integration of the storage device into the vehicle will become increasingly important. Battery monitoring systems (BMS) are expected to become a commodity, penetrating the automotive volume market from both highly equipped premium cars and dedicated fuel-economy vehicles (e.g. stop/start). Battery monitoring systems will allow for more aggressive battery operating strategies, at the same time improving the reliability of the power supply system. Where a single lead-acid battery cannot fulfil the increasing demands, dual-storage systems may form a cost-efficient extension. They consist either of two lead-acid batteries or of a lead-acid battery plus another storage device.

Developing a dynamic life cycle greenhouse gas emission inventory for wood construction for two different end-of-life scenarios

Treesearch

Richard D. Bergman; James Salazar; Scott Bowe

2012-01-01

Static life cycle assessment does not fully describe the carbon footprint of construction wood because of carbon changes in the forest and product pools over time. This study developed a dynamic greenhouse gas (GHG) inventory approach using US Forest Service and life-cycle data to estimate GHG emissions on construction wood for two different end-of-life scenarios....

A Methodology for Integrated, Multiregional Life Cycle Assessment Scenarios under Large-Scale Technological Change.

PubMed

Gibon, Thomas; Wood, Richard; Arvesen, Anders; Bergesen, Joseph D; Suh, Sangwon; Hertwich, Edgar G

2015-09-15

Climate change mitigation demands large-scale technological change on a global level and, if successfully implemented, will significantly affect how products and services are produced and consumed. In order to anticipate the life cycle environmental impacts of products under climate mitigation scenarios, we present the modeling framework of an integrated hybrid life cycle assessment model covering nine world regions. Life cycle assessment databases and multiregional input-output tables are adapted using forecasted changes in technology and resources up to 2050 under a 2 °C scenario. We call the result of this modeling "technology hybridized environmental-economic model with integrated scenarios" (THEMIS). As a case study, we apply THEMIS in an integrated environmental assessment of concentrating solar power. Life-cycle greenhouse gas emissions for this plant range from 33 to 95 g CO2 eq./kWh across different world regions in 2010, falling to 30-87 g CO2 eq./kWh in 2050. Using regional life cycle data yields insightful results. More generally, these results also highlight the need for systematic life cycle frameworks that capture the actual consequences and feedback effects of large-scale policies in the long term.

THE COMPONENTS OF KIN COMPETITION

PubMed Central

Van Dyken, J. David

2011-01-01

It is well known that competition among kin alters the rate and often the direction of evolution in subdivided populations. Yet much remains unclear about the ecological and demographic causes of kin competition, or what role life cycle plays in promoting or ameliorating its effects. Using the multilevel Price equation, I derive a general equation for evolution in structured populations under an arbitrary intensity of kin competition. This equation partitions the effects of selection and demography, and recovers numerous previous models as special cases. I quantify the degree of kin competition, α, which explicitly depends on life cycle. I show how life cycle and demographic assumptions can be incorporated into kin selection models via α, revealing life cycles that are more or less permissive of altruism. As an example, I give closed-form results for Hamilton’s rule in a three-stage life cycle. Although results are sensitive to life cycle in general, I identify three demographic conditions that give life cycle invariant results. Under the infinite island model, α is a function of the scale of density regulation and dispersal rate, effectively disentangling these two phenomena. Population viscosity per se does not impede kin selection. PMID:20482610

[Specific manifestations of polyvariant life cycles in ground beetles (Coleoptera, Carabidae) along latitudinal gradient].

PubMed

Matalin, A V

2014-01-01

The life cycles of Carabidae are highly diverse, and 25 variants of these cycles are realized In the European part of Russia, from semideserts to continental tundras. The diversity of the life cycle spectrum sharply decreases (by more than half) upon transition from nemoral to boreal forest communities, and its phenological unification takes place at high latitudes. The greatest proportion of species with polyvariant development (25%) is characteristic of temporal latitudes, which may be explained by relatively long growing season and considerable cenotic diversity. In both southern (semidesert and steppe) and northern regions (middle and northern boreal forests), this proportion does not exceed 5%. At low latitudes, the polyvariant pattern of development is often manifested in the form of facultative bivoltine life cycles or as facultative biennial life cycles in species with the initial "spring" breeding type.

USING LIFE CYCLE ASSESSMENT TOOLS FOR INTEGRATED PRODUCT POLICY

EPA Science Inventory

The European Union's new Integrated Product Policy directs governments and companies to consider the entire product life cycle, from cradle to grave, in their environmental decision-making process. A life-cycle based approach is intended to lead toward true environmental improvem...

41 CFR 109-1.5304 - Deviations.

Code of Federal Regulations, 2010 CFR

2010-07-01

... High Risk Personal Property § 109-1.5304 Deviations. (a) Life cycle control determinations. When the HFO approves a contractor program containing controls, other than life cycle control consistent with... Secretary for Procurement and Assistance Management. A HFO's decision not to provide life-cycle control...

41 CFR 109-1.5304 - Deviations.

Code of Federal Regulations, 2013 CFR

2013-07-01

... High Risk Personal Property § 109-1.5304 Deviations. (a) Life cycle control determinations. When the HFO approves a contractor program containing controls, other than life cycle control consistent with... Secretary for Procurement and Assistance Management. A HFO's decision not to provide life-cycle control...

41 CFR 109-1.5304 - Deviations.

Code of Federal Regulations, 2014 CFR

2014-01-01

... High Risk Personal Property § 109-1.5304 Deviations. (a) Life cycle control determinations. When the HFO approves a contractor program containing controls, other than life cycle control consistent with... Secretary for Procurement and Assistance Management. A HFO's decision not to provide life-cycle control...

41 CFR 109-1.5304 - Deviations.

Code of Federal Regulations, 2012 CFR

2012-01-01

... High Risk Personal Property § 109-1.5304 Deviations. (a) Life cycle control determinations. When the HFO approves a contractor program containing controls, other than life cycle control consistent with... Secretary for Procurement and Assistance Management. A HFO's decision not to provide life-cycle control...

41 CFR 109-1.5304 - Deviations.

Code of Federal Regulations, 2011 CFR

2011-01-01

... High Risk Personal Property § 109-1.5304 Deviations. (a) Life cycle control determinations. When the HFO approves a contractor program containing controls, other than life cycle control consistent with... Secretary for Procurement and Assistance Management. A HFO's decision not to provide life-cycle control...

Development of computer software for pavement life cycle cost analysis.

DOT National Transportation Integrated Search

1988-01-01

The life cycle cost analysis program (LCCA) is designed to automate and standardize life cycle costing in Virginia. It allows the user to input information necessary for the analysis, and it then completes the calculations and produces a printed copy...

EVALUATING THE GREENNESS OF IONIC LIQUIDS VIA LIFE CYCLE ASSESSMENT

EPA Science Inventory

Ionic Liquids have been suggested as "greener" replacements to traditional solvents. However, the environmental impacts of the life cycle phases have not been studied. Such a "cradle to gate" Life Cycle Assessment (LCA) for comparing the environmental impact of various solvents...

LIFE CYCLE DESIGN FRAMEWORK AND DEMONSTRATION PROJECTS - PROFILES OF AT&T AND ALLIED SIGNAL

EPA Science Inventory

This document offers guidance and practical experience for integrating environmental considerations into product system development. Life cycle design seeks to minimize the environmental burden associated with a product's life cycle from raw materials acquisition through manufact...

Garvin Heath | NREL

Science.gov Websites

& Impacts Analysis Group in the Strategic Energy Analysis Center. Areas of Expertise Life cycle environmental impacts of energy technologies, including externalities Life cycle assessment Sustainability ;Life Cycle Assessment of a Parabolic Trough Concentrating Solar Power Plant and the Impacts of Key

From life cycle talking to taking action

EPA Science Inventory

The series of Life Cycle Management (LCM) conferences has aimed to create a platform for users and developers of life cycle assessment tools to share their experiences as they challenge traditional environmental management practices, which are narrowly confined (“gate-to-gate”) a...

Moving Up the CMMI Capability and Maturity Levels Using Simulation

DTIC Science & Technology

2008-01-01

Alternative Process Tools, Including NPV and ROI 6 Figure 3: Top-Level View of the Full Life-Cycle Version of the IEEE 12207 PSIM, Including IV&V Layer 19...Figure 4: Screenshot of the Incremental Version Model 19 Figure 5: IEEE 12207 PSIM Showing the Top-Level Life-Cycle Phases 22 Figure 6: IEEE 12207 ...Software Detailed Design for the IEEE 12207 Life- Cycle Process 24 Figure 8: Incremental Life Cycle PSIM Configured for a Specific Project Using SEPG

User’s Guide for Naval Material Command’s Life Cycle Cost (FLEX) Model.

DTIC Science & Technology

1982-04-01

MATERIAL COMMANDl’S 3 LIFE CYCLE COST (FLEX) MODEL Icc FoIuhrInomto -- -- P ea eCo tc Pleale Cona, ______ _____-Thims document rc~ ofl 5C72 -lot REPORT...Material Command’s Life Cycle Cost (FLEX) Prep. 4/82 ___ Model ______________ ______________ 7. Author(s) S. Performing Organization Rapt. No. R. Dress (ESA...WANG 1I. Abstract (Limit: 200 words) The FLEX-9E life cycle cost comp~uter model is a user-oriented methodology accommodating most cost structures and

A dynamo theory prediction for solar cycle 22: Sunspot number, radio flux, exospheric temperature, and total density at 400 km

NASA Technical Reports Server (NTRS)

Schatten, K. H.; Hedin, A. E.

1986-01-01

Using the dynamo theory method to predict solar activity, a value for the smoothed sunspot number of 109 + or - 20 is obtained for solar cycle 22. The predicted cycle is expected to peak near December, 1990 + or - 1 year. Concommitantly, F(10.7) radio flux is expected to reach a smoothed value of 158 + or - 18 flux units. Global mean exospheric temperature is expected to reach 1060 + or - 50 K and global total average total thermospheric density at 400 km is expected to reach 4.3 x 10 to the -15th gm/cu cm + or - 25 percent.

Strength, Fatigue, and Fracture Toughness of Ti-6Al-4V Liner from a Composite Over-Wrapped Pressure Vessel

NASA Technical Reports Server (NTRS)

Salem, Jonathan A.; Lerch, Brad; Thesken, John C.; Sutter, Jim; Russell, Richard

2008-01-01

It was demonstrated by way of experiment that Composite Over-wrapped Pressure Vessel (COPV) Ti-6Al-4V liner material can sustain the expected service loads and cycles. The experiments were performed as part of investigations on the residual life of COPV tanks being used in Space Shuttle Orbiters. Measured properties included tensile strength, compressive strength, reversed loading cycles to simulate liner proof strains, and cyclic fatigue loading to demonstrate the ability to sustain 1000 cycles after liner buckling. The liner material came from a salvaged 40 in. Columbia (orbiter 102) tank (SN029), and tensile strength measurements were made on both boss-transition (thick) and membrane regions (thin). The average measured yield strength was 131 ksi in the boss-transition and membrane regions, in good agreement with measurements made on 1970 s vintage forged plate stock. However, Young s modulus was 17.4+/-0.3 Msi, somewhat higher than typical handbook values (approx.16 Msi). The fracture toughness, as estimated from a failed fatigue specimen, was 74 ksi/sq in, in reasonable agreement with standardized measurements made on 1970 s vintage forged plate stock. Low cycle fatigue of a buckled test specimen implied that as-imprinted liners can sustain over 4000 load cycles.

Effect of KOH concentration on LEO cycle life of IPV nickel-hydrogen flight cell - Update II

NASA Technical Reports Server (NTRS)

Smithrick, John J.; Hall, Stephen W.

1992-01-01

An update of validation test results confirming the breakthrough in LEO cycle life of nickel-hydrogen cells containing 26 percent KOH electrolyte is presented. A breakthrough in the LEO cycle life of individual pressure vessel (IPV) nickel-hydrogen cells has been previously reported. The cycle life of boiler plate cells containing 26 percent potassium hydroxide (KOH) electrolyte was about 40,000 LEO cycles, compared to 3500 cycles for cells containing 31 percent KOH. The cycle regime was a stressful accelerated LEO, which consisted of a 27.5 min charge followed by a 17.5 min discharge (2X normal rate). The depth-of-discharge was 80 percent. Six 48-Ah Hughes recirculation design IPV nickel-hydrogen flight battery cells are being evaluated. Three of the cells contain 26 percent KOH (test cells), and three contain 31 percent KOH (control cells). They are undergoing real time LEO cycle life testing. The cycle regime is a 90-min LEO orbit consisting of a 54-min charge followed by a 36-min discharge. The depth-of-discharge is 80 percent. The cell temperature is maintained at 10 C. The three 31 percent KOH cells failed (cycles 3729, 4165, and 11355). One of the 26 percent KOH cells failed at cycle 15314. The other two 26 percent KOH cells were cycled for over 16,000 cycles during the continuing test.

Evolutionary implications of the adaptation to different immune systems in a parasite with a complex life cycle

PubMed Central

Hammerschmidt, Katrin; Kurtz, Joachim

2005-01-01

Many diseases are caused by parasites with complex life cycles that involve several hosts. If parasites cope better with only one of the different types of immune systems of their host species, we might expect a trade-off in parasite performance in the different hosts, that likely influences the evolution of virulence. We tested this hypothesis in a naturally co-evolving host–parasite system consisting of the tapeworm Schistocephalus solidus and its intermediate hosts, a copepod, Macrocyclops albidus, and the three-spined stickleback Gasterosteus aculeatus. We did not find a trade-off between infection success in the two hosts. Rather, tapeworms seem to trade-off adaptation towards different parts of their hosts' immune systems. Worm sibships that performed better in the invertebrate host also seem to be able to evade detection by the fish innate defence systems, i.e. induce lower levels of activation of innate immune components. These worm variants were less harmful for the fish host likely due to reduced costs of an activated innate immune system. These findings substantiate the impact of both hosts' immune systems on parasite performance and virulence. PMID:16271977

Stochastic Technology Choice Model for Consequential Life Cycle Assessment.

PubMed

Kätelhön, Arne; Bardow, André; Suh, Sangwon

2016-12-06

Discussions on Consequential Life Cycle Assessment (CLCA) have relied largely on partial or general equilibrium models. Such models are useful for integrating market effects into CLCA, but also have well-recognized limitations such as the poor granularity of the sectoral definition and the assumption of perfect oversight by all economic agents. Building on the Rectangular-Choice-of-Technology (RCOT) model, this study proposes a new modeling approach for CLCA, the Technology Choice Model (TCM). In this approach, the RCOT model is adapted for its use in CLCA and extended to incorporate parameter uncertainties and suboptimal decisions due to market imperfections and information asymmetry in a stochastic setting. In a case study on rice production, we demonstrate that the proposed approach allows modeling of complex production technology mixes and their expected environmental outcomes under uncertainty, at a high level of detail. Incorporating the effect of production constraints, uncertainty, and suboptimal decisions by economic agents significantly affects technology mixes and associated greenhouse gas (GHG) emissions of the system under study. The case study also shows the model's ability to determine both the average and marginal environmental impacts of a product in response to changes in the quantity of final demand.

[Development of technologies of population health management in Kazakhstan based on an integrated assessment of the combined exposure to environmental factors].

PubMed

Sraubaev, E N; Serik, B

2013-01-01

At present there is overdue necessity of an integral approach to the assessment of health status and the impact of environmental factors on it, in the development of science-based management decisions and programs on improvement of the health status of the population of Kazakhstan and in the increase in life expectancy from the birth and healthy life expectancy. The purpose of the proposed program--improving health and increasing life expectancy from the birth and healthy life expectancy of the population of Kazakhstan. Based on a meta-analysis to justify the target age group in which an implementation of complex of preventive measures will increase both the life expectancy from the birth and healthy life expectancy, to perform a comprehensive health screening for the basic classes of diseases and behavioral characteristics of the target group in the course of a multicentre studies to give a comprehensive hygienic characteristics of the ecological status of the studied regions and to develop the Health Passport of the region, to develop a model of the combined effects of environmental factors on health; to create a theoretical model for the calculation of life expectancy from the birth and healthy life expectancy, taking into account the limits of modifiability of factors that affect them, and justify a comprehensive program of management decisions on modification of factors, to carry out pilot studies on the development and validation technological (managemental) solutions to control modifiable factors that affect life expectancy from the birth and healthy life expectancy.

Information system life-cycle and documentation standards, volume 1

NASA Technical Reports Server (NTRS)

Callender, E. David; Steinbacher, Jody

1989-01-01

The Software Management and Assurance Program (SMAP) Information System Life-Cycle and Documentation Standards Document describes the Version 4 standard information system life-cycle in terms of processes, products, and reviews. The description of the products includes detailed documentation standards. The standards in this document set can be applied to the life-cycle, i.e., to each phase in the system's development, and to the documentation of all NASA information systems. This provides consistency across the agency as well as visibility into the completeness of the information recorded. An information system is software-intensive, but consists of any combination of software, hardware, and operational procedures required to process, store, or transmit data. This document defines a standard life-cycle model and content for associated documentation.

Impact of late diagnosis and treatment on life expectancy in people with HIV-1: UK Collaborative HIV Cohort (UK CHIC) Study

PubMed Central

Gompels, Mark; Delpech, Valerie; Porter, Kholoud; Post, Frank; Johnson, Margaret; Dunn, David; Palfreeman, Adrian; Gilson, Richard; Gazzard, Brian; Hill, Teresa; Walsh, John; Fisher, Martin; Orkin, Chloe; Ainsworth, Jonathan; Bansi, Loveleen; Phillips, Andrew; Leen, Clifford; Nelson, Mark; Anderson, Jane; Sabin, Caroline

2011-01-01

Objectives To estimate life expectancy for people with HIV undergoing treatment compared with life expectancy in the general population and to assess the impact on life expectancy of late treatment, defined as CD4 count <200 cells/mm3 at start of antiretroviral therapy. Design Cohort study. Setting Outpatient HIV clinics throughout the United Kingdom. Population Adult patients from the UK Collaborative HIV Cohort (UK CHIC) Study with CD4 count ≤350 cells/mm3 at start of antiretroviral therapy in 1996-2008. Main outcome measures Life expectancy at the exact age of 20 (the average additional years that will be lived by a person after age 20), according to the cross sectional age specific mortality rates during the study period. Results 1248 of 17 661 eligible patients died during 91 203 person years’ follow-up. Life expectancy (standard error) at exact age 20 increased from 30.0 (1.2) to 45.8 (1.7) years from 1996-9 to 2006-8. Life expectancy was 39.5 (0.45) for male patients and 50.2 (0.45) years for female patients compared with 57.8 and 61.6 years for men and women in the general population (1996-2006). Starting antiretroviral therapy later than guidelines suggest resulted in up to 15 years’ loss of life: at age 20, life expectancy was 37.9 (1.3), 41.0 (2.2), and 53.4 (1.2) years in those starting antiretroviral therapy with CD4 count <100, 100-199, and 200-350 cells/mm3, respectively. Conclusions Life expectancy in people treated for HIV infection has increased by over 15 years during 1996-2008, but is still about 13 years less than that of the UK population. The higher life expectancy in women is magnified in those with HIV. Earlier diagnosis and subsequent timely treatment with antiretroviral therapy might increase life expectancy. PMID:21990260

Toluene stability Space Station Rankine power system

NASA Technical Reports Server (NTRS)

Havens, V. N.; Ragaller, D. R.; Sibert, L.; Miller, D.

1987-01-01

A dynamic test loop is designed to evaluate the thermal stability of an organic Rankine cycle working fluid, toluene, for potential application to the Space Station power conversion unit. Samples of the noncondensible gases and the liquid toluene were taken periodically during the 3410 hour test at 750 F peak temperature. The results obtained from the toluene stability loop verify that toluene degradation will not lead to a loss of performance over the 30-year Space Station mission life requirement. The identity of the degradation products and the low rates of formation were as expected from toluene capsule test data.

High performing actuation system for use with a louver array for satellite thermal control. [design and performance tests on prototype Bourdon spiral configuration

NASA Technical Reports Server (NTRS)

Reusser, P. U.; Coebergh, J. A. F.

1973-01-01

A high performing actuation system has been developed to drive one pair or a set of 9 pairs of louver blades. The system uses a Bourdon spiral as the driving member. The response time of the liquid expansion of the spiral system is in the order of three seconds. Besides performance tests, qualification tests have been carried out on a prototype system, demonstrating that the actuation system withstands normal launching conditions; projected operating life of 7 years with more than 7000 cycles can be expected.

Polylactic acid trays for fresh-food packaging: A Carbon Footprint assessment.

PubMed

Ingrao, Carlo; Tricase, Caterina; Cholewa-Wójcik, Agnieszka; Kawecka, Agnieszka; Rana, Roberto; Siracusa, Valentina

2015-12-15

This paper discusses application of Carbon Footprint (CF) for quantification of the 100-year Global Warming Potential (GWP100) associated with the life cycle of polylactic acid (PLA) trays for packaging of fresh foods. A comparison with polystyrene (PS)-based trays was done considering two different transport system scenarios for PLA-granule supply to the tray production firm: a transoceanic freight vessel and an intercontinental freight aircraft. Doing so enabled estimation of the influence of the transportation phase on the GHG-emission rate associated with the PLA-trays' life cycle. From the assessment, the GWP100 resulted to be mainly due to PLA-granulate production and to its transportation to the tray manufacturing facility. Also, the study documented that, depending upon the transport system considered, the CF associated with the life cycle of the PLA trays can worsen so much that the latter are no longer GHG-emission saving as they are expected to be compared to the PS ones. Therefore, based upon the findings of the study, it was possible for the authors to understand the importance and the need of accounting for the transport-related issues in the design of PLA-based products, thus preserving their environmental soundness compared to traditional petroleum-based products. In this context, the study could be used as the base to reconsider the merits of PLA usage for product manufacturing, especially when high distances are implied, as in this analysed case. So, the authors believe that new research and policy frameworks should be designed and implemented for both development and promotion of more globally sustainable options. Copyright © 2015 Elsevier B.V. All rights reserved.

Overexpression of NAC gene from Lepidium latifolium L. enhances biomass, shortens life cycle and induces cold stress tolerance in tobacco: potential for engineering fourth generation biofuel crops.

PubMed

Grover, Atul; Singh, Sadhana; Pandey, Pankaj; Patade, Vikas Yadav; Gupta, Sanjay Mohan; Nasim, M

2014-11-01

We report elevated biomass and altered growth characteristics of tobacco plants up on transformation with a NAC (NAM, ATAF1/2,CUC2) gene (GenBank Accession FJ754254) isolated from Lepidium latifolium L. (LlaNAC). Transgenic plants showed significant differences in fresh weight, midrib length of longest leaf, leaf area, height of the plant, root and shoot weights, etc. during vegetative phase. On 100th day after sowing (DAS), plants of transgenic lines were 2-3 times taller than the wild type plants, though no significant difference was recorded in moisture contents of any of the plant tissues. Over-expression of NAC gene up to 2,000 fold was recorded in leaves of transgenic plants on 100th DAS. Interestingly, transgenic plants showed significantly shortened (P(t) = 0.02-0.04) life cycle, as they showed a completely altered growth behaviour. Transgenic plants entered reproductive phase earlier by 60 days, with lines NC2 and NC7b entering first, followed by line NC10. However, the time period spent in the reproductive phase by the plant was nearly twice in case of transgenic lines NC2, NC7b and NC10, as compared to the wild type plants. Despite that, these lines completed their life cycle in 45-60 days lesser than the time taken by wild-type tobacco plants. No difference was recorded in fruit and seed yield of transgenic or wild type plants. To the best of our knowledge, this is the first report on over-expression of NAC gene causing altered growth and biomass patterns. We expect this study to become an important reference towards future engineering of plants for fuel and fodder purposes.

Using aggregated single patient (N-of-1) trials to determine the effectiveness of psychostimulants to reduce fatigue in advanced cancer patients: a rationale and protocol.

PubMed

Senior, Hugh Ej; Mitchell, Geoffrey K; Nikles, Jane; Carmont, Sue-Ann; Schluter, Philip J; Currow, David C; Vora, Rohan; Yelland, Michael J; Agar, Meera; Good, Phillip D; Hardy, Janet R

2013-04-23

It is estimated that 29% of deaths in Australia are caused by malignant disease each year and can be expected to increase with population ageing. In advanced cancer, the prevalence of fatigue is high at 70-90%, and can be related to the disease and/or the treatment. The negative impact of fatigue on function (physical, mental, social and spiritual) and quality of life is substantial for many palliative patients as well as their families/carers. This paper describes the design of single patient trials (n-of-1 s or SPTs) of a psychostimulant, methylphenidate hydrochloride (MPH) (5 mg bd), compared to placebo as a treatment for fatigue, with a population estimate of the benefit by the aggregation of multiple SPTs. Forty patients who have advanced cancer will be enrolled through specialist palliative care services in Australia. Patients will complete up to 3 cycles of treatment. Each cycle is 6 days long and has 3 days treatment and 3 days placebo. The order of treatment and placebo is randomly allocated for each cycle. The primary outcome is a reduction in fatigue severity as measured by the Functional Assessment of Cancer Therapy-fatigue subscale (FACIT-F). Secondary outcomes include adverse events, quality of life, additional fatigue assessments, depression and Australian Karnovsky Performance Scale. This study will provide high-level evidence using a novel methodological approach about the effectiveness of psychostimulants for cancer-related fatigue. If effective, the findings will guide clinical practice in reducing this prevalent condition to improve function and quality of life. Australian New Zealand Clinical Trials Registry ACTRN12609000794202.

Impact of homicide and traffic crashes on life expectancy in the largest Latin American country.

PubMed

Auger, Nathalie; Le Serbon, Emilie; Rasella, Davide; Aquino, Rosana; Barreto, Maurício L

2016-09-01

Brazil and Canada are on opposite poles of the spectrum for life expectancy in America. We identified factors underlying Brazil's lower life expectancy relative to Canada, with emphasis on the role of injury compared with other major causes. We computed life expectancy at birth in Brazil and Canada in 2010 and identified the ages and causes of death responsible for the gap between both countries. The main outcome measure was the contribution of homicide and traffic accidents to the gap, compared with other causes of death. Relative to Canada, life expectancy was lower in Brazil by 8.2 years (men) and 5.2 years (women). Injury lowered life expectancy of men in Brazil by 2.2 years, or more than a quarter of the gap, mainly due to homicide and traffic accidents between ages 20 and 64 years. Homicide and traffic accidents contributed more than all circulatory diseases combined. In women, circulatory disease was the most important cause of lower life expectancy. In 2010, homicides and traffic accidents were the principal cause for short life expectancy of men in Brazil. Improving life expectancy in Brazil requires addressing the root causes of inequalities that drive illicit drug trade, violence and accidents. © The Author 2015. Published by Oxford University Press on behalf of Faculty of Public Health. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

48 CFR 211.274-1 - General.

Code of Federal Regulations, 2012 CFR

2012-10-01

... on leading practices and embraces open standards, DoD can— (a) Achieve lower life-cycle cost of item management and improve life-cycle property management; (b) Improve operational readiness; (c) Provide reliable accountability of property and asset visibility throughout the life cycle; and (d) Reduce the...

48 CFR 211.274-1 - General.

Code of Federal Regulations, 2011 CFR

2011-10-01

... on leading practices and embraces open standards, DoD can— (a) Achieve lower life-cycle cost of item management and improve life-cycle property management; (b) Improve operational readiness; (c) Provide reliable accountability of property and asset visibility throughout the life cycle; and (d) Reduce the...

48 CFR 211.274-1 - General.

Code of Federal Regulations, 2013 CFR

2013-10-01

... on leading practices and embraces open standards, DoD can— (a) Achieve lower life-cycle cost of item management and improve life-cycle property management; (b) Improve operational readiness; (c) Provide reliable accountability of property and asset visibility throughout the life cycle; and (d) Reduce the...

Reducing Life-Cycle Costs.

ERIC Educational Resources Information Center

Roodvoets, David L.

2003-01-01

Presents factors to consider when determining roofing life-cycle costs, explaining that costs do not tell the whole story; discussing components that should go into the decision (cost, maintenance, energy use, and environmental costs); and concluding that important elements in reducing life-cycle costs include energy savings through increased…

Software security checklist for the software life cycle

NASA Technical Reports Server (NTRS)

Gilliam, D. P.; Wolfe, T. L.; Sherif, J. S.

2002-01-01

A formal approach to security in the software life cycle is essential to protect corporate resources. However, little thought has been given to this aspect of software development. Due to its criticality, security should be integrated as a formal approach in the software life cycle.

EDITORIAL: THE INTERNATIONAL CONFERENCE ON LIFE CYCLE ASSESSMENT

EPA Science Inventory

This is a special issue of Journal of Life Cycle Assessment that includes selected papers from the Internatonal Conference and Exhibition on Life Cycle Assessment (InLCA). In April 2000, the EPA, with co-organizer IERE, held the InLCA conferencethat attracted over 265 attendees (...

LIFE CYCLE DESIGN OF AMORPHOUS SILICON PHOTOVOLTAIC MODULES

EPA Science Inventory

The life cycle design framework was applied to photovoltaic module design. The primary objective of this project was to develop and evaluate design metrics for assessing and guiding the Improvement of PV product systems. Two metrics were used to assess life cycle energy perform...

Test of US Federal Life Cycle Inventory Data Interoperability

EPA Science Inventory

Life cycle assessment practitioners must gather data from a variety of sources. For modeling activities in the US, practitioners may wish to use life cycle inventory data from public databases and libraries provided by US government entities. An exercise was conducted to test if ...

Holistic impact assessment and cost savings of rainwater harvesting at the watershed scale

EPA Science Inventory

We evaluated the impacts of domestic and agricultural rainwater harvesting (RWH) systems in three watersheds within the Albemarle-Pamlico river basin (southeastern U.S.) using life cycle assessment (LCA) and life cycle cost assessment. Life cycle impact assessment (LCIA) categori...

Educational Focuses in Organisational Life Cycles.

ERIC Educational Resources Information Center

Miller, Harry G.

1985-01-01

Presents four stages frequently associated with the stages of an organization's life cycle: experimentation, growth, maturity, and decline or stability. The author also demonstrates that the impact of employment and thus training related to organizational life cycles suggests a need for understanding the technical preparation required for…

PRODUCT LIFE-CYCLE ASSESSMENT: INVENTORY GUIDELINES AND PRINCIPLES

EPA Science Inventory

The Life Cycle Assessment (LCA) can be used as an objective technical tool to evaluate the environmental consequences of a product, process, or activity holistically, across its entire life cycle. omplete LCA can be viewed as consisting of three complementary components (1) the i...

1977 Nationwide Personal Transportation Study : a life cycle of travel by the American family

DOT National Transportation Integrated Search

1981-07-01

This report provides information about family trips and travel from the point of view of the family life cycle, using data from the 1977 Nationwide Personal Transportation Study. Daily travel characteristics of families in stages of four life cycles ...

26 CFR 1.401(a)(9)-9 - Life expectancy and distribution period tables.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 26 Internal Revenue 5 2014-04-01 2014-04-01 false Life expectancy and distribution period tables... Plans, Etc. § 1.401(a)(9)-9 Life expectancy and distribution period tables. Q-1. What is the life...)(9)? A-1 The following table, referred to as the Single Life Table, is used for determining the life...

Question order sensitivity of subjective well-being measures: focus on life satisfaction, self-rated health, and subjective life expectancy in survey instruments.

PubMed

Lee, Sunghee; McClain, Colleen; Webster, Noah; Han, Saram

2016-10-01

This study examines the effect of question context created by order in questionnaires on three subjective well-being measures: life satisfaction, self-rated health, and subjective life expectancy. We conducted two Web survey experiments. The first experiment (n = 648) altered the order of life satisfaction and self-rated health: (1) life satisfaction asked immediately after self-rated health; (2) self-rated health immediately after life satisfaction; and (3) two items placed apart. We examined their correlation coefficient by experimental condition and further examined its interaction with objective health. The second experiment (n = 479) asked life expectancy before and after parental mortality questions. Responses to life expectancy were compared by order using ANOVA, and we examined interaction with parental mortality status using ANCOVA. Additionally, response time and probes were examined. Correlation coefficients between self-rated health and life satisfaction differed significantly by order: 0.313 (life satisfaction first), 0.508 (apart), and 0.643 (self-rated health first). Differences were larger among respondents with chronic conditions. Response times were the shortest when self-rated health was asked first. When life expectancy asked after parental mortality questions, respondents reported considering parents more for answering life expectancy; and respondents with deceased parents reported significantly lower expectancy, but not those whose parents were alive. Question context effects exist. Findings suggest placing life satisfaction and self-rated health apart to avoid artificial attenuation or inflation in their association. Asking about parental mortality prior to life expectancy appears advantageous as this leads respondents to consider parental longevity more, an important factor for true longevity.

Taxation and life expectancy in Western Europe.

PubMed

Bagger, P J

2004-06-01

With the exception of Denmark, life expectancy in Western Europe has shown a significant increase over the last decades. During that period of time overall taxation has increased in most of the countries, especially in Denmark. We, therefore, examined whether taxation could influence life expectancy in Western Europe. We used information on the sum of income tax and employees' social contribution in percentage of gross wage earnings from the OECD database and data on disability adjusted life expectancy at birth from the World Health Organization database. We arbitrarily only included countries with populations in excess of 4 millions and thereby excluded smaller countries where tax exemption is part of the national monetary policy. We found that disability adjusted life expectancy at birth was inversely correlated to the total tax burden in Western Europe. We speculate whether a threshold exists where high taxes exert a negative influence on life expectancy despite increased welfare spending. The study suggests that tax burden should be considered among the multiple factors influencing life expectancy.

A Language Translator for a Computer Aided Rapid Prototyping System.

DTIC Science & Technology

1988-03-01

PROBLEM ................... S B. THE TRADITIONAL "WATERFALL LIFE CYCLE" .. ............... 14 C. RAPID PROTOTYPING...feature of everyday life for almost the entire industrialized world. Few governments or businesses function without the aid of computer systems. Com...engineering. B. TIE TRADITIONAL "WATERFALL LIFE CYCLE" I. Characteristics The traditional method of software engineering is the "waterfall life cycle

A Growth Model for the Academic Program Life Cycle (APLC): A Theoretical and Empirical Analysis. IR Applications, Volume 33

ERIC Educational Resources Information Center

Acquah, Edward H. K.

2012-01-01

The academic program life cycle (APLC) concept states each program's life flows through several stages: introduction, growth, maturity, and decline. A mixed-influence diffusion growth model is fitted to annual enrollment data on academic programs to analyze the factors determining progress of academic programs through their life cycles. The…

Mercury Conditions for the MESSENGER Mission Simulated in High- Solar-Radiation Vacuum Tests

NASA Technical Reports Server (NTRS)

Wong, Wayne A.

2003-01-01

The MESSENGER (Mercury Surface, Space Environment, Geochemistry, and Ranging) spacecraft, planned for launch in March 2004, will perform two flybys of Mercury before entering a year-long orbit of the planet in September 2009. The mission will provide opportunities for detailed characterization of the surface, interior, atmosphere, and magnetosphere of the closest planet to the Sun. The NASA Glenn Research Center and the MESSENGER spacecraft integrator, the Johns Hopkins University Applied Physics Laboratory, have partnered under a Space Act Agreement to characterize a variety of critical components and materials under simulated conditions expected near Mercury. Glenn's Vacuum Facility 6, which is equipped with a solar simulator, can simulate the vacuum and high solar radiation anticipated in Mercury orbit. The MESSENGER test hardware includes a variety of materials and components that are being characterized during the Tank 6 vacuum tests, where the hardware will be exposed to up to 11 suns insolation, simulating conditions expected in Mercury orbit. In 2002, ten solar vacuum tests were conducted, including beginning of life, end of life, backside exposure, and solar panel thermal shock cycling tests. Components tested include candidate solar array panels, sensors, thermal shielding materials, and communication devices. As an example, for the solar panel thermal shock cycling test, two candidate solar array panels were suspended on a lift mechanism that lowered the panels into a liquid-nitrogen-cooled box. After reaching -140 C, the panels were then lifted out of the box and exposed to the equivalent of 6 suns (8.1 kilowatts per square meters). After five cold soak/heating cycles were completed successfully, there was no apparent degradation in panel performance. An anticipated 100-hr thermal shield life test is planned for autumn, followed by solar panel flight qualification tests in winter. Glenn's ongoing support to the MESSENGER program has been instrumental in identifying design solutions and validating thermal performance models under a very aggressive development schedule. The test data have assisted Johns Hopkins engineers in selecting a flight solar array vendor and a thermal shield design. MESSENGER is one in a series of missions in NASA's Discovery Program. Infrared thermography provides data on the thermal gradients in the MESSENGER components during high solar insolation vacuum testing.

The numbers game: quantitative analysis of Neorickettsia sp. propagation through complex life cycle of its digenean host using real-time qPCR.

PubMed

Greiman, Stephen E; Tkach, Vasyl V

2016-07-01

Bacteria of the genus Neorickettsia are obligate intracellular endosymbionts of parasitic flukes (Digenea) and are passed through the entire complex life cycle of the parasite by vertical transmission. Several species of Neorickettsia are known to cause diseases in domestic animals, wildlife, and humans. Quantitative data on the transmission of the bacteria through the digenean life cycle is almost completely lacking. This study quantified for the first time the abundance of Neorickettsia within multiple stages of the life cycle of the digenean Plagiorchis elegans. Snails Lymnaea stagnalis collected from a pond in North Dakota were screened for the presence of digenean cercariae, which were subsequently tested for the presence of Neorickettsia. Three L. stagnalis were found shedding P. elegans cercariae infected with Neorickettsia. These snails were used to initiate three separate laboratory life cycles and obtain all life cycle stages for bacterial quantification. A quantitative real-time PCR assay targeting the GroEL gene was developed to enumerate Neorickettsia sp. within different stages of the digenean life cycle. The number of bacteria significantly increased throughout all stages, from eggs to adults. The two largest increases in number of bacteria occurred during the period from eggs to cercariae and from 6-day metacercariae to 48-h juvenile worms. These two periods seem to be the most important for Neorickettsia propagation through the complex digenean life cycle and maturation in the definitive host.

[Saving motives in young, middle-aged, and older adults. Preliminary results of a new inventory for exploring lifespan saving motives].

PubMed

Rager, B; Lang, F R; Wagner, G G

2012-12-01

There is some research on personal reasons for saving money in the economic sciences. However, not much is known about the age differences of saving motives. In this vein, the future time perspective (FTP) is known to play a critical role for motivation across the life span. In this study, we introduce a new Saving Motive Inventory (SMI), which also covers saving goals after retirement. Furthermore, it is argued that additional saving motives that are not based on economic models of life-cycle saving also exist. In accordance with the socio-emotional selectivity theory, we explored age differences in an online survey with 496 participants from young (19-44 years), middle-aged (45-64 years), and older (65-86 years) adulthood, who completed a questionnaire on saving motives, personality, and future-related thinking (e.g., Future Time Perspective Scale, Life Orientation Test). Results of the explorative Factor Analysis (EFA) are consistent with the theoretical expectations. The factors are generativity, educational investment, consumption, indifference, and provision for death and dying. Together these five factors account for 67% of the variance. In general, the inventory is reliable and valid with respect to the expected internal and external criteria. It contributes to better understanding of saving motives over the lifespan, especially with respect to effects of the future time perspective.

Comparative muscle development of scyphozoan jellyfish with simple and complex life cycles.

PubMed

Helm, Rebecca R; Tiozzo, Stefano; Lilley, Martin K S; Lombard, Fabien; Dunn, Casey W

2015-01-01

Simple life cycles arise from complex life cycles when one or more developmental stages are lost. This raises a fundamental question - how can an intermediate stage, such as a larva, be removed, and development still produce a normal adult? To address this question, we examined the development in several species of pelagiid jellyfish. Most members of Pelagiidae have a complex life cycle with a sessile polyp that gives rise to ephyrae (juvenile medusae); but one species within Pelagiidae, Pelagia noctiluca, spends its whole life in the water column, developing from a larva directly into an ephyra. In many complex life cycles, adult features develop from cell populations that remain quiescent in larvae, and this is known as life cycle compartmentalization and may facilitate the evolution of direct life cycles. A second type of metamorphic processes, known as remodeling, occurs when adult features are formed through modification of already differentiated larval structures. We examined muscle morphology to determine which of these alternatives may be present in Pelagiidae. We first examined the structure and development of polyp and ephyra musculature in Chrysaora quinquecirrha, a close relative of P. noctiluca with a complex life cycle. Using phallotoxin staining and confocal microscopy, we verified that polyps have four to six cord muscles that persist in strobilae and discovered that cord muscles is physically separated from ephyra muscle. When cord muscle is removed from ephyra segments, normal ephyra muscle still develops. This suggests that polyp cord muscle is not necessary for ephyra muscle formation. We also found no evidence of polyp-like muscle in P. noctiluca. In both species, we discovered that ephyra muscle arises de novo in a similar manner, regardless of the life cycle. The separate origins of polyp and ephyra muscle in C. quinquecirrha and the absence of polyp-like muscle in P. noctiluca suggest that polyp muscle is not remodeled to form ephyra muscle in Pelagiidae. Life cycle stages in Scyphozoa may instead be compartmentalized. Because polyp muscle is not directly remodeled, this may have facilitated the loss of the polyp stage in the evolution of P. noctiluca.

A Darwinian approach to the origin of life cycles with group properties.

PubMed

Rashidi, Armin; Shelton, Deborah E; Michod, Richard E

2015-06-01

A selective explanation for the evolution of multicellular organisms from unicellular ones requires knowledge of both selective pressures and factors affecting the response to selection. Understanding the response to selection is particularly challenging in the case of evolutionary transitions in individuality, because these transitions involve a shift in the very units of selection. We develop a conceptual framework in which three fundamental processes (growth, division, and splitting) are the scaffold for unicellular and multicellular life cycles alike. We (i) enumerate the possible ways in which these processes can be linked to create more complex life cycles, (ii) introduce three genes based on growth, division and splitting that, acting in concert, determine the architecture of the life cycles, and finally, (iii) study the evolution of the simplest five life cycles using a heuristic model of coupled ordinary differential equations in which mutations are allowed in the three genes. We demonstrate how changes in the regulation of three fundamental aspects of colonial form (cell size, colony size, and colony cell number) could lead unicellular life cycles to evolve into primitive multicellular life cycles with group properties. One interesting prediction of the model is that selection generally favors cycles with group level properties when intermediate body size is associated with lowest mortality. That is, a universal requirement for the evolution of group cycles in the model is that the size-mortality curve be U-shaped. Furthermore, growth must decelerate with size. Copyright © 2015 Elsevier Inc. All rights reserved.

Impact of hot events at different developmental stages of a moth: the closer to adult stage, the less reproductive output

PubMed Central

Zhang, Wei; Chang, Xiang-Qian; Hoffmann, AryA.; Zhang, Shu; Ma, Chun-Sen

2015-01-01

Hot days in summer (involving a few hours at particularly high temperatures) are expected to become more common under climate change. How such events at different life stages affect survival and reproduction remains unclear in most organisms. Here, we investigated how an exposure to 40 °C at different life stages in the global insect pest, Plutella xylostella, affects immediate survival, subsequent survival and reproductive output. First-instar larvae showed the lowest survival under heat stress, whereas 3rd-instar larvae were relatively heat resistant. Heat exposure at the 1st-instar or egg stage did not influence subsequent maturation success, while exposure at the 3rd-instar larval stage did have an effect. We found that heat stress at developmental stages closer to adult stage caused greater detrimental effects on reproduction than heat stress experienced at earlier life stages. The effects of hot events on insect populations can therefore depend critically on the timing of the event relative to an organism’s life-cycle. PMID:26000790

Geographical variation in life expectancy at birth in England and Wales is largely explained by deprivation.

PubMed

Woods, Laura M; Rachet, Bernard; Riga, Michael; Stone, Noell; Shah, Anjali; Coleman, Michel P

2005-02-01

To describe the population mortality profile of England and Wales by deprivation and in each government office region (GOR) during 1998, and to quantify the influence of geography and deprivation in determining life expectancy. Construction of life tables describing age specific mortality rates and life expectancy at birth from death registrations and estimated population counts. Life tables were created for (a) quintiles of income deprivation based on the income domain score of the index of multiple deprivation 2000, (b) each GOR and Wales, and (c) every combination of deprivation and geography. England and Wales.PATIENTS/ PARTICIPANTS: Residents of England and Wales, 1998. Life expectancy at birth varies with deprivation quintile and is highest in the most affluent groups. The differences are mainly attributable to differences in mortality rates under 75 years of age. Regional life expectancies display a clear north-south gradient. Linear regression analysis shows that deprivation explains most of the geographical variation in life expectancy. Geographical patterns of life expectancy identified within these data for England and Wales in 1998 are mainly attributable to variations in deprivation status as defined by the IMD 2000 income domain score.

MACHINING ELIMINATION THROUGH APPLICATION OF THREAD FORMING FASTENERS IN NET SHAPED CAST HOLES

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cleaver, Ryan J; Cleaver, Todd H; Talbott, Richard

The ultimate objective of this work was to eliminate approximately 30% of the machining performed in typical automotive engine and transmission plants by using thread forming fasteners in as-cast holes of aluminum and magnesium cast components. The primary issues at the source of engineers reluctance to implementing thread forming fasteners in lightweight castings are: * Little proof of consistency of clamp load vs. input torque in either aluminum or magnesium castings. * No known data to understand the effect on consistency of clamp load as casting dies wear. The clamp load consistency concern is founded in the fact that amore » portion of the input torque used to create clamp load is also used to create threads. The torque used for thread forming may not be consistent due to variations in casting material, hole size and shape due to tooling wear and process variation (thermal and mechanical). There is little data available to understand the magnitude of this concern or to form the basis of potential solutions if the range of clamp load variation is very high (> +/- 30%). The range of variation that can be expected in as-cast hole size and shape over the full life cycle of a high pressure die casting die was established in previous work completed by Pacific Northwest National Laboratory, (PNNL). This established range of variation was captured in a set of 12 cast bosses by designing core pins at the size and draft angles identified in the sited previous work. The cast bosses were cut into nuts that could be used in the Ford Fastener Laboratory test-cell to measure clamp load when a thread forming fastener was driven into a cast nut. There were two sets of experiments run. First, a series of cast aluminum nuts were made reflecting the range of shape and size variations to be expected over the life cycle of a die casting die. Taptite thread forming fasteners, (a widely used thread forming fastener suitable for aluminum applications), were driven into the various cored, as-cast nuts at a constant input torque and resulting clamp loads were recorded continuously. The clamp load data was used to determine the range of clamp loads to be expected. The bolts were driven to failure. The clamp load corresponding to the target input of 18.5 Nm was recorded for each fastener. In a like fashion, a second set of experiments were run with cast magnesium nuts and ALtracs thread forming fasteners, (a widely used thread forming fastener suitable for magnesium applications). Again all clamp loads were recorded and analyzed similarly to the Taptites in aluminum cast nuts. Results from previous work performed on the same test cell for a Battelle project using standard M8 bolts into standard M8 nuts were included as a comparator for a standard bolt and nut application. The results for the thread forming fasteners in aluminum cast holes were well within industry expectations of +/- 30% for out of the box and robustness range testing. The results for the dry and lubed extreme conditions were only slightly higher than industry expectations at +/- 35.6%. However, when compared to the actual Battelle results (+/- 40%) for a standard bolt and nut the tread forming fasteners performed slightly better. The results for the thread forming fasteners in magnesium cast holes were all well within industry expectations of +/- 30% for all three conditions. The robustness range (.05mm larger and smaller holes than the expected wear pattern of a die casting die at full life cycle) results also fell within the industry expectations for standard threaded fasteners. These results were very encouraging. It was concluded that this work showed that clamp load variation with thread forming fasteners is consistent with industry expectations for standard steel bolts and nuts at +/- 30%. There does not appear to be any significant increase in clamp load variation due to the application of thread forming fasteners in as-cast holes of aluminum or magnesium over the effective life of a die casting mold. The fully implemented potential benefit of thread forming fasteners in as-cast holes of aluminum and magnesium is estimated to be 6 trillion Btu per year for North America. Economic benefit is estimated to be nearly $800 million per year. Environmental benefits and quality improvements will also result from full implementation of this technology.« less

Earth Without Life: A Systems Model of a Global Abiotic Nitrogen Cycle

NASA Astrophysics Data System (ADS)

Laneuville, M.; Kameya, M.; Cleaves, H. J.

2017-07-01

N is the major component of the atmosphere and plays important roles in biochemistry. Presently, the surface N-cycle is dominated by biology. However, before the origin of life, abiotic N-cycling would have set the stage for the origin of life.

LIFE CYCLE IMPACT ASSESSMENT AN INTRODUCTION AND INTERNATIONAL UPDATE

EPA Science Inventory

Research within the field of Life Cycle Impact Assessment (LCIA) has greatly improved since the work of Heijungs and Guinee in 1992. Within the UNEP / SETAC Life Cycle Initiative an effort is underway to provide recommendations about the direction of research and selection of LC...

Achieving Our Environmental Sustainability Goals: The Opportunities and Pitfalls of Applying Life Cycle Thinking

EPA Science Inventory

An increasing number of people around the world are beginning to realize that a systems approach, such as life cycle thinking, is necessary to truly achieve environmental sustainability. Without the holistic perspective that life cycle thinking provides, our actions risk leading ...

Dealing with Emergy Algebra in the Life Cycle Assessment Framework

EPA Science Inventory

The Life Cycle Inventory (LCI) represents one of the four steps of the Life Cycle Assessment (LCA) methodology, which is a standardized procedure (ISO 14040:2006) to estimate the environmental impacts generated by the production, use and disposal of goods and services. In this co...

Comparison of energy-based indicators used in life cycle assessment tools for buildings

EPA Science Inventory

Traditionally, building rating systems focused on, among others, energy used during operational stage. Recently, there is a strong push by these rating systems to include the life cycle energy use of buildings, particularly using Life Cycle Assessment (LCA), by offering credits t...

10 CFR 436.24 - Uncertainty analyses.

Code of Federal Regulations, 2011 CFR

2011-01-01

... Procedures for Life Cycle Cost Analyses § 436.24 Uncertainty analyses. If particular items of cost data or... impact of uncertainty on the calculation of life cycle cost effectiveness or the assignment of rank order... and probabilistic analysis. If additional analysis casts substantial doubt on the life cycle cost...

10 CFR 436.24 - Uncertainty analyses.

Code of Federal Regulations, 2013 CFR

2013-01-01

... Procedures for Life Cycle Cost Analyses § 436.24 Uncertainty analyses. If particular items of cost data or... impact of uncertainty on the calculation of life cycle cost effectiveness or the assignment of rank order... and probabilistic analysis. If additional analysis casts substantial doubt on the life cycle cost...

10 CFR 436.24 - Uncertainty analyses.

Code of Federal Regulations, 2014 CFR

2014-01-01

... Procedures for Life Cycle Cost Analyses § 436.24 Uncertainty analyses. If particular items of cost data or... impact of uncertainty on the calculation of life cycle cost effectiveness or the assignment of rank order... and probabilistic analysis. If additional analysis casts substantial doubt on the life cycle cost...

10 CFR 436.24 - Uncertainty analyses.

Code of Federal Regulations, 2012 CFR

2012-01-01

... Procedures for Life Cycle Cost Analyses § 436.24 Uncertainty analyses. If particular items of cost data or... impact of uncertainty on the calculation of life cycle cost effectiveness or the assignment of rank order... and probabilistic analysis. If additional analysis casts substantial doubt on the life cycle cost...

LIFE-CYCLE IMPACT ASSESSMENT DEMONSTRATION FOR THE BGU-24

EPA Science Inventory

The primary goal of this project was to develop and demonstrate a life-cycle impact assessment (LCIA) approach using existing life-cycle inventory (LCI) data on one of the propellants, energetics, and pyrotechnic (PEP) materials of interest to the U.S. Department of Defense (DoD)...

A Game to Teach the Life Cycles of Fungi

ERIC Educational Resources Information Center

Blum, Abraham

1976-01-01

Presented is a biological game utilized to teach fungi life cycles to secondary biology students. The game is designed to overcome difficulties of correlating schematic drawings with images seen through the microscope, correlating life cycles of fungi and host, and understanding cyclic development of fungi. (SL)

10 CFR 436.11 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-01-01

... Life Cycle Cost Analyses § 436.11 Definitions. As used in this subpart— Base Year means the fiscal year in which a life cycle cost analysis is conducted. Building energy system means an energy conservation... building that improve energy efficiency and are life cycle cost effective and that involve energy...

Integrated Metrics for Improving the Life Cycle Approach to Assessing Product System Sustainability

EPA Science Inventory

Life cycle approaches are critical for identifying and managing to reduce burdens in the sustainability of product systems. While these methods can indicate potential environmental impacts of a product, current Life Cycle Assessment (LCA) methods fail to integrate the multiple im...

The Process of Life Cycle Cost Analysis: Projecting Economic Consequences of Design Decisions

ERIC Educational Resources Information Center

AIA Journal, 1976

1976-01-01

Life-cycle cost analysis deals with both present and future costs and attempts to relate the two as a basis for making decisions. This article lays the groundwork for a better understanding of the techniques of life-cycle cost analysis. (Author/MLF)

THE EPA'S EMERGING FOCUS ON LIFE CYCLE ASSESSMENT

EPA Science Inventory

EPA has been actively engaged in LCA research since 1990 to help advance the methodology and application of life cycle thinking in decision making. Across the Agency consideration of the life cycle concept is increasing in the development of policies and programs. A major force i...

Power flattening on modified CANDLE small long life gas-cooled fast reactor

NASA Astrophysics Data System (ADS)

Monado, Fiber; Su'ud, Zaki; Waris, Abdul; Basar, Khairul; Ariani, Menik; Sekimoto, Hiroshi

2014-09-01

Gas-cooled Fast Reactor (GFR) is one of the candidates of next generation Nuclear Power Plants (NPPs) that expected to be operated commercially after 2030. In this research conceptual design study of long life 350 MWt GFR with natural uranium metallic fuel as fuel cycle input has been performed. Modified CANDLE burn-up strategy with first and second regions located near the last region (type B) has been applied. This reactor can be operated for 10 years without refuelling and fuel shuffling. Power peaking reduction is conducted by arranging the core radial direction into three regions with respectively uses fuel volume fraction 62.5%, 64% and 67.5%. The average power density in the modified core is about 82 Watt/cc and the power peaking factor decreased from 4.03 to 3.43.

Relationships between the Active Aging Index and Disability-Free Life Expectancy: A Case Study in the Rajshahi District of Bangladesh.

PubMed

Tareque, Md Ismail; Hoque, Nazrul; Islam, Towfiqua Mahfuza; Kawahara, Kazuo; Sugawa, Makiko

2013-12-01

Life expectancy has increased considerably throughout the world. In Bangladesh, life expectancy has increased from about 53 years in 1975 to 69 years in 2010. However, it is unknown whether the increase in life expectancy is simultaneously accompanied by an increase in disability-free life expectancy (DFLE). The purpose of the study described in this article was to explore the relationship between life expectancy and DFLE in the Rajshahi District of Bangladesh by examining the relationships between the Active Aging Index (AAI) and DFLE. The study fi ndings suggest that urban, more-educated, elderly males are more active in all aspects of life and have longer DFLE. Females are found to outlive males but are more likely to live a greater part of their remaining life with disability. Positive correlations between the AAI and DFLE suggest that older adults could enjoy more DFLE by involving themselves in active aging activities.

NASA Lewis advanced IPV nickel-hydrogen technology

NASA Technical Reports Server (NTRS)

Smithrick, John J.; Britton, Doris L.

1993-01-01

Individual pressure vessel (IPV) nickel-hydrogen technology was advanced at NASA Lewis and under Lewis contracts. Some of the advancements are as follows: to use 26 percent potassium hydroxide electrolyte to improve cycle life and performance, to modify the state of the art cell design to eliminate identified failure modes and further improve cycle life, and to develop a lightweight nickel electrode to reduce battery mass, hence reduce launch and/or increase satellite payload. A breakthrough in the LEO cycle life of individual pressure vessel nickel-hydrogen battery cells was reported. The cycle life of boiler plate cells containing 26 percent KOH electrolyte was about 40,000 accelerated LEO cycles at 80 percent DOD compared to 3,500 cycles for cells containing 31 percent KOH. Results of the boiler plate cell tests have been validated at NWSC, Crane, Indiana. Forty-eight ampere-hour flight cells containing 26 and 31 percent KOH have undergone real time LEO cycle life testing at an 80 percent DOD, 10 C. The three cells containing 26 percent KOH failed on the average at cycle 19,500. The three cells containing 31 percent KOH failed on the average at cycle 6,400. Validation testing of NASA Lewis 125 Ah advanced design IPV nickel-hydrogen flight cells is also being conducted at NWSC, Crane, Indiana under a NASA Lewis contract. This consists of characterization, storage, and cycle life testing. There was no capacity degradation after 52 days of storage with the cells in the discharged state, on open circuit, 0 C, and a hydrogen pressure of 14.5 psia. The catalyzed wall wick cells have been cycled for over 22,694 cycles with no cell failures in the continuing test. All three of the non-catalyzed wall wick cells failed (cycles 9,588; 13,900; and 20,575). Cycle life test results of the Fibrex nickel electrode has demonstrated the feasibility of an improved nickel electrode giving a higher specific energy nickel-hydrogen cell. A nickel-hydrogen boiler plate cell using an 80 mil thick, 90 percent porous Fibrex nickel electrode has been cycled for 10,000 cycles at 40 percent DOD.

Fractographic evaluation of creep effects on strain-controlled fatigue-cracking of AISI 304LC and 316 stainless steel

NASA Technical Reports Server (NTRS)

Oldrieve, R. E.

1978-01-01

Analysis of high temperature low cycle fatigue of AISI 304LC and 316 stainless steels by the method of strainrange partitioning results in four separate strainrange versus life relationships, depending upon the way in which creep-strain and plastic strain are combined within a cycle. Fractography is used in this investigation of the creep-fatigue interaction associated with these cycles. The PP and PC-cycle fractures were transgranular. The PC-cycle resulted in fewer cycles of initiation and shorter total cyclic life for the same applied inelastic strainrange. The CC-cycle had mixed transgranular and intergranular fracture, fewer cycles of initiation and shorter cycle life than PP or PC. The CP-cycle had fully integranular cracking, and failed in fewer cycles than were required for cracks to initate for PP,PC, and CC.

Decomposition of educational differences in life expectancy by age and causes of death among South Korean adults.

PubMed

Jung-Choi, Kyunghee; Khang, Young-Ho; Cho, Hong-Jun; Yun, Sung-Cheol

2014-06-05

Decomposition of socioeconomic inequalities in life expectancy by ages and causes allow us to better understand the nature of socioeconomic mortality inequalities and to suggest priority areas for policy and intervention. This study aimed to quantify age- and cause-specific contributions to socioeconomic differences in life expectancy at age 25 by educational level among South Korean adult men and women. We used National Death Registration records in 2005 (129,940 men and 106,188 women) and national census data in 2005 (15, 215, 523 men and 16,077,137 women aged 25 and over). Educational attainment as the indicator of socioeconomic position was categorized into elementary school graduation or less, middle or high school graduation, and college graduation or higher. Differences in life expectancy at age 25 by educational level were estimated by age- and cause-specific mortality differences using Arriaga's decomposition method. Differences in life expectancy at age 25 between college or higher education and elementary or less education were 16.23 years in men and 7.69 years in women. Young adult groups aged 35-49 in men and aged 25-39 in women contributed substantially to the differences between college or higher education and elementary or less education in life expectancy. Suicide and liver disease were the most important causes of death contributing to the differences in life expectancy in young adult groups. For older age groups, cerebrovascular disease and lung cancer were important to explain educational differential in life expectancy at 25-29 between college or higher education and middle or higher education. The contribution of the causes of death to socioeconomic inequality in life expectancy at age 25 in South Korea varied by age groups and differed by educational comparisons. The age specific contributions for different causes of death to life expectancy inequalities by educational attainment should be taken into account in establishing effective policy strategies to reduce socioeconomic inequalities in life expectancy.

Life expectancy in HIV-positive persons in Switzerland: matched comparison with general population

PubMed Central

Gueler, Aysel; Moser, André; Calmy, Alexandra; Günthard, Huldrych F.; Bernasconi, Enos; Furrer, Hansjakob; Fux, Christoph A.; Battegay, Manuel; Cavassini, Matthias; Vernazza, Pietro; Zwahlen, Marcel; Egger, Matthias

2017-01-01

Objectives: To estimate life expectancy over 25 years in HIV-positive people and to compare their life expectancy with recent estimates for the general population, by education. Methods: Patients aged 20 years or older enrolled in the Swiss HIV Cohort Study 1988–2013 were eligible. Patients alive in 2001 were matched to up to 100 Swiss residents, by sex, year of birth, and education. Life expectancy at age 20 was estimated for monotherapy (1988–1991), dual therapy (1992–1995), early combination antiretroviral therapy (cART, 1996–1998), later cART (1999–2005) and recent cART (2006–2013) eras. Parametric survival regression was used to model life expectancy. Results: In all, 16 532 HIV-positive patients and 927 583 residents were included. Life expectancy at age 20 of HIV-positive individuals increased from 11.8 years [95% confidence interval (CI) 11.2–12.5] in the monotherapy era to 54.9 years (95% CI 51.2–59.6) in the most recent cART era. Differences in life expectancy across educational levels emerged with cART. In the most recent cART period, life expectancy at age 20 years was 52.7 years (95% CI 46.4–60.1) with compulsory education, compared to 60.0 years (95% CI 53.4–67.8) with higher education. Estimates for the general population were 61.5 and 65.6 years, respectively. Male sex, smoking, injection drug use, and low CD4+ cell counts at enrolment were also independently associated with mortality. Conclusion: In Switzerland, educational inequalities in life expectancy were larger among HIV-infected persons than in the general population. Highly educated HIV-positive people have an estimated life expectancy similar to Swiss residents with compulsory education. Earlier start of cART and effective smoking-cessation programs could improve HIV-positive life expectancy further and reduce inequalities. PMID:27831953

Decomposition of socio-economic differences in life expectancy at birth by age and cause of death among 4 million South Korean public servants and their dependents.

PubMed

Khang, Young-Ho; Yang, Seungmi; Cho, Hong-Jun; Jung-Choi, Kyunghee; Yun, Sung-Cheol

2010-12-01

Differences in life expectancy at birth across social classes can be more easily interpreted as a measure of absolute inequalities in survival. This study quantified age- and cause-specific contributions to life expectancy differences by income among 4 million public servants and their dependents in South Korea (9.1% of the total Korean population). Using 9-year mortality follow-up data (208,612 deaths) on 4,055,150 men and women aged 0-94 years, with national health insurance premiums imposed proportionally based on monthly salary as a measure of income, differences in life expectancy at birth by income were estimated by age- and cause-specific mortality differences using Arriaga's decomposition method. Life expectancy at birth gradually increased with income. Differences in life expectancy at birth between the highest and the lowest income quartile were 6.22 years in men and 1.74 years in women. Mortality differentials by income among those aged ≥50 years contributed most substantially (80.4% in men and 85.6% in women) to the socio-economic differences in life expectancy at birth. In men, cancers (stomach, liver and lung), cardiovascular diseases (stroke), digestive diseases (liver cirrhosis) and external causes (transport accidents and suicide) were important contributors to the life expectancy differences. In women, the contribution of ill-defined causes was most important. Cardiovascular diseases (stroke and hypertensive disease) and external causes (transport accidents and suicide) also contributed to the life expectancy differences in women while the contributions of cancers and digestive diseases were minimal. Reductions in socio-economic differentials in mortality from stroke and external causes (transport accidents and suicide) among middle-aged and older men and women would significantly contribute to equalizing life expectancy among income groups. Policy efforts to reduce mortality differentials in major cancers (stomach, liver and lung) and liver cirrhosis are also important for eliminating Korean men's socio-economic inequalities in life expectancy.

Intimacy and the life cycle in the marital relationships of the Scottish elite during the long eighteenth century.

PubMed

Barclay, Katie

2011-01-01

Traditionally marriage has been treated as one step in the life cycle, between youth and old age, singleness and widowhood. Yet an approach to the life cycle that treats marriage as a single step in a person's life is overly simplistic. During the eighteenth century many marriages were of considerable longevity during which time couples aged together and power dynamics within the home were frequently renegotiated to reflect changing circumstances. This study explores how intimacy developed and changed over the life cycle of marriage and what this meant for power, through a study of the correspondence of two elite Scottish couples.

A decision model to estimate a risk threshold for venous thromboembolism prophylaxis in hospitalized medical patients.

PubMed

Le, P; Martinez, K A; Pappas, M A; Rothberg, M B

2017-06-01

Essentials Low risk patients don't require venous thromboembolism (VTE) prophylaxis; low risk is unquantified. We used a Markov model to estimate the risk threshold for VTE prophylaxis in medical inpatients. Prophylaxis was cost-effective for an average medical patient with a VTE risk of ≥ 1.0%. VTE prophylaxis can be personalized based on patient risk and age/life expectancy. Background Venous thromboembolism (VTE) is a common preventable condition in medical inpatients. Thromboprophylaxis is recommended for inpatients who are not at low risk of VTE, but no specific risk threshold for prophylaxis has been defined. Objective To determine a threshold for prophylaxis based on risk of VTE. Patients/Methods We constructed a decision model with a decision-tree following patients for 3 months after hospitalization, and a lifetime Markov model with 3-month cycles. The model tracked symptomatic deep vein thromboses and pulmonary emboli, bleeding events and heparin-induced thrombocytopenia. Long-term complications included recurrent VTE, post-thrombotic syndrome and pulmonary hypertension. For the base case, we considered medical inpatients aged 66 years, having a life expectancy of 13.5 years, VTE risk of 1.4% and bleeding risk of 2.7%. Patients received enoxaparin 40 mg day -1 for prophylaxis. Results Assuming a willingness-to-pay (WTP) threshold of $100 000/ quality-adjusted life year (QALY), prophylaxis was indicated for an average medical inpatient with a VTE risk of ≥ 1.0% up to 3 months after hospitalization. For the average patient, prophylaxis was not indicated when the bleeding risk was > 8.1%, the patient's age was > 73.4 years or the cost of enoxaparin exceeded $60/dose. If VTE risk was < 0.26% or bleeding risk was > 19%, the risks of prophylaxis outweighed benefits. The prophylaxis threshold was relatively insensitive to low-molecular-weight heparin cost and bleeding risk, but very sensitive to patient age and life expectancy. Conclusions The decision to offer prophylaxis should be personalized based on patient VTE risk, age and life expectancy. At a WTP of $100 000/QALY, prophylaxis is not warranted for most patients with a 3-month VTE risk below 1.0%. © 2017 International Society on Thrombosis and Haemostasis.

Aerothermal modeling. Executive summary

NASA Technical Reports Server (NTRS)

Kenworthy, M. K.; Correa, S. M.; Burrus, D. L.

1983-01-01

One of the significant ways in which the performance level of aircraft turbine engines has been improved is by the use of advanced materials and cooling concepts that allow a significant increase in turbine inlet temperature level, with attendant thermodynamic cycle benefits. Further cycle improvements have been achieved with higher pressure ratio compressors. The higher turbine inlet temperatures and compressor pressure ratios with corresponding higher temperature cooling air has created a very hostile environment for the hot section components. To provide the technology needed to reduce the hot section maintenance costs, NASA has initiated the Hot Section Technology (HOST) program. One key element of this overall program is the Aerothermal Modeling Program. The overall objective of his program is to evolve and validate improved analysis methods for use in the design of aircraft turbine engine combustors. The use of such combustor analysis capabilities can be expected to provide significant improvement in the life and durability characteristics of both combustor and turbine components.

The direct-stress fatigue strength of 17S-T aluminum alloy throughout the range from 1/2 to 500,000,000 cycles of stress

NASA Technical Reports Server (NTRS)

Hartmann, E C; Stickley, G W

1942-01-01

Fatigue-test were conducted on six specimens made from 3/4-inch-diameter 17S-T rolled-and-drawn rod for the purpose of obtaining additional data on the fatigue life of the material at stresses up to the static strength. The specimens were tested in direct tension using a stress range from zero to a maximum in tension. A static testing machine was used to apply repeated loads in the case of the first three specimens; the other three specimens were tested in a direct tension-compression fatigue machine. The direct-stress fatigue curve obtained for the material indicates that, in the range of stresses above about two-thirds the tensile strength, the fatigue strength is higher than might be expected by simply extrapolating the ordinary curve of stress plotted against the number of cycles determined at lower stresses.

The Life Cycle of Images: Revisiting the Ethical Treatment of the Art Therapy Image

ERIC Educational Resources Information Center

Hinz, Lisa D.

2013-01-01

Using the metaphor of the human life cycle, the author of this viewpoint suggests that consideration of the birth, life, and death of images made in art therapy may promote a new perspective on their ethical treatment. A developmental view of images encourages art therapists to see art images as living entities that undergo a natural life cycle.…

The Life Cycle of Everyday Stuff.

ERIC Educational Resources Information Center

Reeske, Mike; Ireton, Shirley Watt

Life cycle assessment is an important tool for technology planning as solid waste disposal options dwindle and energy prices continue to increase. This guide investigates the life cycles of products. The activities in this book are suitable for secondary earth science, environmental science, physical science, or integrated science lessons. The…

A life cycle greenhouse gas inventory of a tree production system

Treesearch

Alissa Kendall; E. Gregory McPherson

2012-01-01

PurposeThis study provides a detailed, process-based life cycle greenhouse gas (GHG) inventory of an ornamental tree production system for urban forestry. The success of large-scale tree planting initiatives for climate protection depends on projects being net sinks for CO2 over their entire life cycle....

Sustainability Analysis | Energy Analysis | NREL

Science.gov Websites

environmental, life-cycle, climate, and other impacts of renewable energy technologies. Photo of a man viewing a energy choices within the complex web of connections between energy and water. Life Cycle Assessment Harmonization Our life cycle assessment harmonization provides lenders, utility executives, and lawmakers with

10 CFR 434.607 - Life cycle cost analysis criteria.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 10 Energy 3 2013-01-01 2013-01-01 false Life cycle cost analysis criteria. 434.607 Section 434.607 Energy DEPARTMENT OF ENERGY ENERGY CONSERVATION ENERGY CODE FOR NEW FEDERAL COMMERCIAL AND MULTI-FAMILY HIGH RISE RESIDENTIAL BUILDINGS Building Energy Compliance Alternative § 434.607 Life cycle cost...

10 CFR 434.607 - Life cycle cost analysis criteria.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 10 Energy 3 2014-01-01 2014-01-01 false Life cycle cost analysis criteria. 434.607 Section 434.607 Energy DEPARTMENT OF ENERGY ENERGY CONSERVATION ENERGY CODE FOR NEW FEDERAL COMMERCIAL AND MULTI-FAMILY HIGH RISE RESIDENTIAL BUILDINGS Building Energy Compliance Alternative § 434.607 Life cycle cost...

10 CFR 434.607 - Life cycle cost analysis criteria.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 10 Energy 3 2012-01-01 2012-01-01 false Life cycle cost analysis criteria. 434.607 Section 434.607 Energy DEPARTMENT OF ENERGY ENERGY CONSERVATION ENERGY CODE FOR NEW FEDERAL COMMERCIAL AND MULTI-FAMILY HIGH RISE RESIDENTIAL BUILDINGS Building Energy Compliance Alternative § 434.607 Life cycle cost...

Enhancing TSM&O strategies through life cycle benefit/cost analysis : life cycle benefit/cost analysis & life cycle assessment of adaptive traffic control systems and ramp metering systems.

DOT National Transportation Integrated Search

2015-05-01

The research team developed a comprehensive Benefit/Cost (B/C) analysis framework to evaluate existing and anticipated : intelligent transportation system (ITS) strategies, particularly, adaptive traffic control systems and ramp metering systems, : i...

LIFE CYCLE BASED STUDIES ON BIOETHANOL FUEL FOR SUSTAINABLE TRANSPORTATION: A LITERATURE REVIEW

EPA Science Inventory

A literature search was conducted and revealed 45 publications (1996-2005) that compare bio-ethanol systems to conventional fuel on a life-cycle basis, or using life cycle assessment. Feedstocks, such as sugar beets, wheat, potato, sugar cane, and corn, have been investigated in...

Life cycle assessment of a commercial rainwater harvesting system compared with a municipal water supply system

EPA Science Inventory

Building upon previously published life cycle assessment (LCA) methodologies, we conducted an LCA of a commercial rainwater harvesting (RWH) system and compared it to a municipal water supply (MWS) system adapted to Washington, D.C. Eleven life cycle impact assessment (LCIA) indi...

LIFE-CYCLE IMPACT ASSESSMENT DEMONSTRATION FOR THE GBU-24

EPA Science Inventory

The primary goal of this project was to develop and demonstrate a life-cycle impact assessment (LCIA) approach using existing life-cycle inventory (LCI) data on one of the propellants, energetics, and pyro-technic (PEP) materials of interest to the U.S. Department of Defense (DoD...

Life-cycle energy and emissions inventories for motorcycles, diesel automobiles, school buses, electric buses, Chicago rail, and New York City rail

DOT National Transportation Integrated Search

2009-05-01

The development of life-cycle energy and emissions factors for passenger transportation modes : is critical for understanding the total environmental costs of travel. Previous life-cycle studies : have focused on the automobile given its dominating s...

LIFE CYCLE DESIGN OF AIR INTAKE MANIFOLDS; PHASE I: 2.0 L FORD CONTOUR AIR INTAKE MANIFOLD

EPA Science Inventory

The project team applied the life cycle design methodology to the design analysis of three alternative air intake manifolds: a sand cast aluminum, brazed aluminum tubular, and nylon composite. The design analysis included a life cycle inventory analysis, environmental regulatory...

THE INTERNATIONAL WORKSHOP ON ELECTRICITY DATA FOR LIFE CYCLE INVENTORIES

EPA Science Inventory

A three day workshop was held in October 2001 to discuss life cycle inventory data for electricity production. Electricity was selected as the topic for discussion since it features very prominently in the LCA results for most product life cycles, yet there is no consistency in h...

10 CFR 436.13 - Presuming cost-effectiveness results.

Code of Federal Regulations, 2010 CFR

2010-01-01

... Methodology and Procedures for Life Cycle Cost Analyses § 436.13 Presuming cost-effectiveness results. (a) If... life cycle cost-effective without further analysis. (b) A Federal agency may presume that an investment in an energy or water conservation measure retrofit to an existing Federal building is not life cycle...

76 FR 34271 - Hewlett Packard, Global Parts Supply Chain, Global Product Life Cycles Management Unit, Including...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-06-13

... DEPARTMENT OF LABOR Employment and Training Administration [TA-W-74,671] Hewlett Packard, Global Parts Supply Chain, Global Product Life Cycles Management Unit, Including Teleworkers Reporting to... Supply Chain, Global Product Life Cycles Management Unit, including teleworkers reporting to Houston...

7 CFR 3560.65 - Reserve account.

Code of Federal Regulations, 2014 CFR

2014-01-01

...-year period. The reserve account analysis is based on either a Capital Needs Assessment or life cycle... Assessment or as part of the original life cycle cost analysis. The cost of conducting either a Capital Needs... Needs Assessment or life cycle cost analysis may be included in the loan financing. (b) For ownership...

7 CFR 3560.65 - Reserve account.

Code of Federal Regulations, 2013 CFR

2013-01-01

...-year period. The reserve account analysis is based on either a Capital Needs Assessment or life cycle... Assessment or as part of the original life cycle cost analysis. The cost of conducting either a Capital Needs... Needs Assessment or life cycle cost analysis may be included in the loan financing. (b) For ownership...

LCACCESS: A GLOBAL DIRECTORY OF LIFE CYCLE ASSESSMENT RESOURCES

EPA Science Inventory

LCAccess is an EPA-sponsored website intended to promote the use of Life Cycle Assessment (LCA) in business decision-making by faciliatating access to data sources that are useful in developing a life cycle inventory (LCI). While LCAccess does not itself contain data, it is a sea...

78 FR 16676 - Agency Information Collection Activities; Proposed Collection; Comment Request; Draft Guidance...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-03-18

... Industry and FDA Staff; Total Product Life Cycle: Infusion Pump--Premarket Notification [510(k... for Industry and FDA Staff; Total Product Life Cycle: Infusion Pump--Premarket Notification [510(k... Staff; Total Product Life Cycle: Infusion Pump--Premarket Notification [510(k)] Submissions--0910-NEW...

LCACCESS: MAKING LIFE CYCLE DATA AVAILABLE VIA THE INTERNET(SYSTEMS ANLAYSIS BRANCH, SUSTAINABLE TECHNOLOGY DIVISION, NRMRL)

EPA Science Inventory

The lack of readily available, quality environmental life cycle inventory (LCI) data is often a barrier to manufacturers, among others, for incorporating life cycle considerations into their decision-making process. While much progress has been made on standardizing and improving...

FUNDAMENTALS OF LIFE CYCLE ASSESSMENT AND OFF-THE-SHELF SOFTWARE DEMONSTRATION

EPA Science Inventory

As the name implies, Life Cycle Assesssment (LCA) evaluates the entire life cycle of a product, process, activity, or service, not just simple economics at the time of delivery. This course on LCA covers the following issues:
Basic principles of LCA for use in producing, des...

Models of the Organizational Life Cycle: Applications to Higher Education.

ERIC Educational Resources Information Center

Cameron, Kim S.; Whetten, David A.

1983-01-01

A review of models of group and organization life cycle development is provided and the applicability of those models for institutions of higher education are discussed. An understanding of the problems and characteristics present in different life cycle stages can help institutions manage transitions more effectively. (Author/MLW)

Life Cycle of a Pencil.

ERIC Educational Resources Information Center

Reeske, Mike

2000-01-01

Explains a project called "Life Cycle of a Pencil" which was developed by the National Science Teachers Association (NSTA) and the U.S. Environmental Protection Agency (USEPA). Describes the life cycle of a pencil in stages starting from the first stage of design to the sixth stage of product disposal. (YDS)

[TRANSFORMATIONS OF LIFE CYCLES IN THE EVOLUTIONARY HISTORY OF TRYPANOSOMATIDS. MACROTRANSFORMATIONS].

PubMed

Frolov, A O; Malysheva, M N; Kostygov, A Yu

2015-01-01

The review concerns analysis of life cycle macrotransformations in the evolutionary history of trypanosomatids. The term "macrotransformations" stands for evolutionary processes leading to the establishment of heteroxenous and secondary homoxenous life cycles within Trypanosomatidae. There were three direct macrotransformations in the evolution of the group resulting in the rise of heteroxenous genera Leishmania, Trypanosoma and Phytomonas, and one case of reverse macrotransformation in trypanosomes of T. (b.) brucei group. The issues of the origin, diversity and phylogeny of taxa whose emergence resulted from macrotransformations of life cycles of homoxenous trypanosomatids.

Are the Performance Based Logistics Prophets Using Science or Alchemy to Create Life-Cycle Affordability? Using Theory to Predict the Efficacy of Performance Based Logistics

DTIC Science & Technology

2013-10-01

Based Logistics Prophets Using Science or Alchemy to Create Life-Cycle Affordability? Using Theory to Predict the Efficacy of Performance Based...Using Science or Alchemy to Create Life-Cycle Affordability? Using Theory to Predict the Efficacy of Performance Based Logistics 5a. CONTRACT NUMBER 5b...Are the PBL Prophets Using Science or Alchemy to Create Life Cycle Affordability? 328Defense ARJ, October 2013, Vol. 20 No. 3 : 325–348 Defense

Life cycle environmental performance of renewable building materials in the context of residential construction : phase II research report: an extension to the 2005 phase I research report. Module C, Life-cycle inventory of hardwood lumber manufacturing in the Northeast and North Central United States.

Treesearch

Richard Bergman; Scott A. Bowe

2008-01-01

The goal of this study was to find the environmental impact of hardwood lumber production through a gate-to-gate Life-Cycle Inventory (LCI) on hardwood sawmills in the northeast and northcentral (NE/NC) United States. Primary mill data was collected per CORRIM Research Guidelines (CORRIM 2001). Life-cycle analysis is beyond the scope of the study.

Life cycle environmental performance of renewable building materials in the context of residential construction : phase II research report: an extension to the 2005 phase I research report. Module L, Life-cycle inventory of hardwood lumber manufacturing in the Southeastern United States.

Treesearch

Richard D. Bergman; Scott A. Bowe

2010-01-01

The goal of this study was to gain an understanding of the environmental impact of hardwood lumber production through a gate-to-gate life-cycle inventory (LCI) of hardwood sawmills in the Southeastern United States (SE). Primary mill data were collected per Consortium on Research for Renewable Industrial Materials (CORRIM) Research Guidelines. Life-cycle impact...

Investigation of the High-Cycle Fatigue Life of Selective Laser Melted and Hot Isostatically Pressed Ti-6Al-4v

DTIC Science & Technology

2015-03-26

INVESTIGATION OF THE HIGH -CYCLE FATIGUE LIFE OF SELECTIVE LASER MELTED AND HOT ISOSTATICALLY PRESSED TI-6AL-4V THESIS Kevin D. Rekedal...ENY-MS-15-M-212 INVESTIGATION OF THE HIGH -CYCLE FATIGUE LIFE OF SELECTIVE LASER MELTED AND HOT ISOSTATICALLY PRESSED TI-6AL-4V THESIS...AFIT-ENY-MS-15-M-212 INVESTIGATION OF THE HIGH -CYCLE FATIGUE LIFE OF SELECTIVE LASER MELTED AND HOT ISOSTATICALLY PRESSED TI-6AL-4V

Making the Mark: The Role of Adenosine Modifications in the Life Cycle of RNA Viruses.

PubMed

Gonzales-van Horn, Sarah R; Sarnow, Peter

2017-06-14

Viral epitranscriptomics is a newly emerging field that has identified unique roles for RNA modifications in modulating life cycles of RNA viruses. Despite the observation of a handful of modified viral RNAs five decades ago, very little was known about how these modifications regulate viral life cycles, until recently. Here we review the pro- and anti-viral effects of methyl-6-adenosine in distinct viral life cycles, the role of 2' O-methyl modifications in RNA stability and innate immune sensing, and functions of adenosine to inosine modifications in retroviral life cycles. With roles for over 100 modifications in RNA still unknown, this is a rapidly emerging field that is destined to suggest novel antiviral therapies. Copyright © 2017 Elsevier Inc. All rights reserved.

Evolution of dispersal in spatially and temporally variable environments: The importance of life cycles.

PubMed

Massol, François; Débarre, Florence

2015-07-01

Spatiotemporal variability of the environment is bound to affect the evolution of dispersal, and yet model predictions strongly differ on this particular effect. Recent studies on the evolution of local adaptation have shown that the life cycle chosen to model the selective effects of spatiotemporal variability of the environment is a critical factor determining evolutionary outcomes. Here, we investigate the effect of the order of events in the life cycle on the evolution of unconditional dispersal in a spatially heterogeneous, temporally varying landscape. Our results show that the occurrence of intermediate singular strategies and disruptive selection are conditioned by the temporal autocorrelation of the environment and by the life cycle. Life cycles with dispersal of adults versus dispersal of juveniles, local versus global density regulation, give radically different evolutionary outcomes that include selection for total philopatry, evolutionary bistability, selection for intermediate stable states, and evolutionary branching points. Our results highlight the importance of accounting for life-cycle specifics when predicting the effects of the environment on evolutionarily selected trait values, such as dispersal, as well as the need to check the robustness of model conclusions against modifications of the life cycle. © 2015 The Author(s). Evolution © 2015 The Society for the Study of Evolution.

Life cycle greenhouse gas emissions and freshwater consumption of Marcellus shale gas.

PubMed

Laurenzi, Ian J; Jersey, Gilbert R

2013-05-07

We present results of a life cycle assessment (LCA) of Marcellus shale gas used for power generation. The analysis employs the most extensive data set of any LCA of shale gas to date, encompassing data from actual gas production and power generation operations. Results indicate that a typical Marcellus gas life cycle yields 466 kg CO2eq/MWh (80% confidence interval: 450-567 kg CO2eq/MWh) of greenhouse gas (GHG) emissions and 224 gal/MWh (80% CI: 185-305 gal/MWh) of freshwater consumption. Operations associated with hydraulic fracturing constitute only 1.2% of the life cycle GHG emissions, and 6.2% of the life cycle freshwater consumption. These results are influenced most strongly by the estimated ultimate recovery (EUR) of the well and the power plant efficiency: increase in either quantity will reduce both life cycle freshwater consumption and GHG emissions relative to power generated at the plant. We conclude by comparing the life cycle impacts of Marcellus gas and U.S. coal: The carbon footprint of Marcellus gas is 53% (80% CI: 44-61%) lower than coal, and its freshwater consumption is about 50% of coal. We conclude that substantial GHG reductions and freshwater savings may result from the replacement of coal-fired power generation with gas-fired power generation.

The components of kin competition.

PubMed

Van Dyken, J David

2010-10-01

It is well known that competition among kin alters the rate and often the direction of evolution in subdivided populations. Yet much remains unclear about the ecological and demographic causes of kin competition, or what role life cycle plays in promoting or ameliorating its effects. Using the multilevel Price equation, I derive a general equation for evolution in structured populations under an arbitrary intensity of kin competition. This equation partitions the effects of selection and demography, and recovers numerous previous models as special cases. I quantify the degree of kin competition, α, which explicitly depends on life cycle. I show how life cycle and demographic assumptions can be incorporated into kin selection models via α, revealing life cycles that are more or less permissive of altruism. As an example, I give closed-form results for Hamilton's rule in a three-stage life cycle. Although results are sensitive to life cycle in general, I identify three demographic conditions that give life cycle invariant results. Under the infinite island model, α is a function of the scale of density regulation and dispersal rate, effectively disentangling these two phenomena. Population viscosity per se does not impede kin selection. © 2010 The Author(s). Journal compilation © 2010 The Society for the Study of Evolution.

A life cycle cost economics model for projects with uniformly varying operating costs. [management planning

NASA Technical Reports Server (NTRS)

Remer, D. S.

1977-01-01

A mathematical model is developed for calculating the life cycle costs for a project where the operating costs increase or decrease in a linear manner with time. The life cycle cost is shown to be a function of the investment costs, initial operating costs, operating cost gradient, project life time, interest rate for capital and salvage value. The results show that the life cycle cost for a project can be grossly underestimated (or overestimated) if the operating costs increase (or decrease) uniformly over time rather than being constant as is often assumed in project economic evaluations. The following range of variables is examined: (1) project life from 2 to 30 years; (2) interest rate from 0 to 15 percent per year; and (3) operating cost gradient from 5 to 90 percent of the initial operating costs. A numerical example plus tables and graphs is given to help calculate project life cycle costs over a wide range of variables.

Association of a trait-like bias towards the perception of negative subjective life events with risk of developing premenstrual symptoms.

PubMed

Gonda, Xenia; Fountoulakis, Konstantinos N; Csukly, Gabor; Telek, Tamas; Pap, Dorottya; Rihmer, Zoltan; Bagdy, Gyorgy

2010-04-16

Premenstrual symptoms affect the majority of healthy women. Premenstrual symptomatology has earlier been linked to stress and a state-like alteration in the perception of life events in the late-luteal phase of the menstrual cycle. We hypothesised that there is also a trait-like negative bias in the perception of life events evident throughout the whole cycle which is associated with the likelihood to manifest more marked symptoms in the late-luteal phase of the cycle. 88 healthy women completed the PRISM calendar for three consecutive cycles and the Objective and Subjective Event Checklist during the follicular phase of the first cycle. Association between PRISM score change from the follicular through the late-luteal phase and life event variables was investigated by Generalized Linear Model Analysis (GENMOD). The PRISM score change showed a significant negative association with the ratio of positive subjective life events and a significant positive association with the ratio of negative subjective life events. There were no significant results in case of the objective life events. Our results indicate that women manifesting a more marked increase of symptoms from the late follicular through the late-luteal phase of the menstrual cycle are more likely to notice negative subjective life events and less likely to notice positive subjective life events. This suggest a trait-like negative bias in the perception of life events present throughout the whole reproductive cycle which may play an important role in the emergence of premenstrual symptoms. Copyright 2010 Elsevier Inc. All rights reserved.

7 CFR 1735.43 - Payments on loans.

Code of Federal Regulations, 2011 CFR

2011-01-01

... date no later than the remaining economic life of the facilities financed by the loan, plus three years..., equals the expected composite economic life of the facilities to be financed, as calculated by RUS; expected composite economic life means the depreciated life plus three years. The expected composite...

Life cycle inventory energy consumption and emissions for biodiesel versus petroleum diesel fueled construction vehicles.

PubMed

Pang, Shih-Hao; Frey, H Christopher; Rasdorf, William J

2009-08-15

Substitution of soy-based biodiesel fuels for petroleum diesel will alter life cycle emissions for construction vehicles. A life cycle inventory was used to estimate fuel cycle energy consumption and emissions of selected pollutants and greenhouse gases. Real-world measurements using a portable emission measurement system (PEMS) were made forfive backhoes, four front-end loaders, and six motor graders on both fuels from which fuel consumption and tailpipe emission factors of CO, HC, NO(x), and PM were estimated. Life cycle fossil energy reductions are estimated it 9% for B20 and 42% for B100 versus petroleum diesel based on the current national energy mix. Fuel cycle emissions will contribute a larger share of total life cycle emissions as new engines enter the in-use fleet. The average differences in life cycle emissions for B20 versus diesel are: 3.5% higher for NO(x); 11.8% lower for PM, 1.6% higher for HC, and 4.1% lower for CO. Local urban tailpipe emissions are estimated to be 24% lower for HC, 20% lower for CO, 17% lower for PM, and 0.9% lower for NO(x). Thus, there are environmental trade-offs such as for rural vs urban areas. The key sources of uncertainty in the B20 LCI are vehicle emission factors.

Ethnic and gender specific life expectancies of the Singapore population, 1965 to 2009 – converging, or diverging?

PubMed Central

2013-01-01

Background The increase in life expectancy and the persistence of expectancy gaps between different social groups in the 20th century are well-described in Western developed countries, but less well documented in the newly industrialised countries of Asia. Singapore, a multiethnic island-state, has undergone a demographic and epidemiologic transition concomitant with economic development. We evaluate secular trends and differences in life expectancy by ethnicity and gender in Singapore, from independence to the present. Methods Period abridged life tables were constructed to derive the life expectancy of the Singapore population from 1965 to 2009 using data from the Department of Statistics and the Registry of Births and Deaths, Singapore. Results All 3 of Singapore’s main ethnic groups, and both genders, experienced an increase in life expectancy at birth and at 65 years from 1965 to 2009, though at substantially different rates. Although there has been a convergence in life expectancy between Indians and Chinese, the (substantial) gap between Malays and the other two ethnic groups has remained. Females continued to have a higher life expectancy at birth and at 65 years than males throughout this period, with no evidence of convergence. Conclusions Ethnic and gender differences in life expectancy persist in Singapore despite its rapid economic development. Targeted chronic disease prevention measures and health promotion activities focusing on people of Malay ethnicity and the male community may be needed to remedy this inequality. PMID:24160733

Outbrief - Long Life Rocket Engine Panel

NASA Technical Reports Server (NTRS)

Quinn, Jason Eugene

2004-01-01

This white paper is an overview of the JANNAF Long Life Rocket Engine (LLRE) Panel results from the last several years of activity. The LLRE Panel has met over the last several years in order to develop an approach for the development of long life rocket engines. Membership for this panel was drawn from a diverse set of the groups currently working on rocket engines (Le. government labs, both large and small companies and university members). The LLRE Panel was formed in order to determine the best way to enable the design of rocket engine systems that have life capability greater than 500 cycles while meeting or exceeding current performance levels (Specific Impulse and Thrust/Weight) with a 1/1,OOO,OOO likelihood of vehicle loss due to rocket system failure. After several meetings and much independent work the panel reached a consensus opinion that the primary issues preventing LLRE are a lack of: physics based life prediction, combined loads prediction, understanding of material microphysics, cost effective system level testing. and the inclusion of fabrication process effects into physics based models. With the expected level of funding devoted to LLRE development, the panel recommended that fundamental research efforts focused on these five areas be emphasized.

Using project life-cycles as guide for timing the archival of scientific data and supporting documentation

NASA Astrophysics Data System (ADS)

Martinez, E.; Glassy, J. M.; Fowler, D. K.; Khayat, M.; Olding, S. W.

2014-12-01

The NASA Earth Science Data Systems Working Groups (ESDSWG) focuses on improving technologies and processes related to science discovery and preservation. One particular group, the Data Preservation Practices, is defining a set of guidelines to aid data providers in planning both what to submit for archival, and when to submit artifacts, so that the archival process can begin early in the project's life cycle. This has the benefit of leveraging knowledge within the project before staff roll off to other work. In this poster we describe various project archival use cases and identify possible archival life cycles that map closely to the pace and flow of work. To understand "archival life cycles", i.e., distinct project phases that produce archival artifacts such as instrument capabilities, calibration reports, and science data products, the workig group initially mapped the archival requirements defined in the Preservation Content Specification to the typical NASA project life cycle. As described in the poster, this work resulted in a well-defined archival life cycle, but only for some types of projects; it did not fit well for condensed project life cycles experienced within airborne and balloon campaigns. To understand the archival process for projects with compressed cycles, the working group gathered use cases from various communities. This poster will describe selected uses cases that provided insight into the unique flow of these projects, as well as proposing archival life cycles that map artifacts to projects with compressed timelines. Finally, the poster will conclude with some early recommendations for data providers, which will be captured in a formal Guidelines document - to be published in 2015.

Using the Inflection Points and Rates of Growth and Decay to Predict Levels of Solar Activity

NASA Technical Reports Server (NTRS)

Wilson, Robert M.; Hathaway, David H.

2008-01-01

The ascending and descending inflection points and rates of growth and decay at specific times during the sunspot cycle are examined as predictors for future activity. On average, the ascending inflection point occurs about 1-2 yr after sunspot minimum amplitude (Rm) and the descending inflection point occurs about 6-7 yr after Rm. The ascending inflection point and the inferred slope (including the 12-mo moving average (12-mma) of (Delta)R (the month-to-month change in the smoothed monthly mean sunspot number (R)) at the ascending inflection point provide strong indications as to the expected size of the ongoing cycle s sunspot maximum amplitude (RM), while the descending inflection point appears to provide an indication as to the expected length of the ongoing cycle. The value of the 12-mma of (Delta)R at elapsed time T = 27 mo past the epoch of RM (E(RM)) seems to provide a strong indication as to the expected size of Rm for the following cycle. The expected Rm for cycle 24 is 7.6 +/- 4.4 (the 90-percent prediction interval), occurring before September 2008. Evidence is also presented for secular rises in selected cycle-related parameters and for preferential grouping of sunspot cycles by amplitude and/or period.

Associations of Smoking, Physical Inactivity, Heavy Drinking, and Obesity with Quality-Adjusted Life Expectancy among US Adults with Depression.

PubMed

Jia, Haomiao; Zack, Matthew M; Gottesman, Irving I; Thompson, William W

2018-03-01

To examine associations between four health behaviors (smoking, physical inactivity, heavy alcohol drinking, and obesity) and three health indices (health-related quality of life, life expectancy, and quality-adjusted life expectancy (QALE)) among US adults with depression. Data were obtained from the 2006, 2008, and 2010 Behavioral Risk Factor Surveillance System data. The EuroQol five-dimensional questionnaire (EQ-5D) health preference scores were estimated on the basis of extrapolations from the Centers for Disease Control and Prevention's healthy days measures. Depression scores were estimated using the eight-item Patient Health Questionnaire. Life expectancy estimates were obtained from US life tables, and QALE was estimated from a weighted combination of the EQ-5D scores and the life expectancy estimates. Outcomes were summarized by depression status for the four health behaviors (smoking, physical inactivity, heavy alcohol drinking, and obesity). For depressed adults, current smokers and the physically inactive had significantly lower EQ-5D scores (0.040 and 0.171, respectively), shorter life expectancy (12.9 and 10.8 years, respectively), and substantially less QALE (8.6 and 10.9 years, respectively). For nondepressed adults, estimated effects were similar but smaller. Heavy alcohol drinking among depressed adults, paradoxically, was associated with higher EQ-5D scores but shorter life expectancy. Obesity was strongly associated with lower EQ-5D scores but only weakly associated with shorter life expectancy. Among depressed adults, physical inactivity and smoking were strongly associated with lower EQ-5D scores, life expectancy, and QALE, whereas obesity and heavy drinking were only weakly associated with these indices. These results suggest that reducing physical inactivity and smoking would improve health more among depressed adults. Copyright © 2018. Published by Elsevier Inc.

[Mortality due to traffic injuries and its impact on life expectancy: a comparison between Mexico and Spain].

PubMed

González-Pérez, Guillermo Julián; Vega-López, María Guadalupe; Cabrera-Pivaral, Carlos Enrique

2015-09-01

To determine the impact of mortality due to motor vehicle traffic injuries (MVTI) compared with other causes of death on life expectancy in Mexico and Spain during the three-year periods 2000-2002 and 2010-2012 and the weight of the different age groups in years of life expectancy lost (YLEL) due to this cause. Based on official death and population data, abridged life tables in Mexico and Spain were constructed for the three-year periods studied. Temporary life expectancy and YLEL for persons aged 15 to 75 years were calculated by selected causes (MVTI, diabetes mellitus, malignant neoplasms and ischemic heart diseases) and age groups in each three-year period. In Spain, YLEL decreased in both sexes from all the causes studied, especially MVTI; this reduction was greater in the younger ages. In addition, temporary life expectancy increased. In Mexico, YLEL due to MVTI increased in men, mainly in young people, and remained unchanged among women. Temporary life expectancy declined in men but increased slightly among women. The reduction in YLEL due to MVTI in Spain has contributed to increased life expectancy. By contrast, the increase in YLEL due to MVTI among Mexican men has contributed to the decline in male life expectancy. Copyright © 2014 SESPAS. Published by Elsevier Espana. All rights reserved.

Monoclonal Antibodies to Intracellular Stages of Cryptosporidium parvum Define Life Cycle Progression In Vitro.

PubMed

Wilke, Georgia; Ravindran, Soumya; Funkhouser-Jones, Lisa; Barks, Jennifer; Wang, Qiuling; VanDussen, Kelli L; Stappenbeck, Thaddeus S; Kuhlenschmidt, Theresa B; Kuhlenschmidt, Mark S; Sibley, L David

2018-06-27

Among the obstacles hindering Cryptosporidium research is the lack of an in vitro culture system that supports complete life development and propagation. This major barrier has led to a shortage of widely available anti- Cryptosporidium antibodies and a lack of markers for staging developmental progression. Previously developed antibodies against Cryptosporidium were raised against extracellular stages or recombinant proteins, leading to antibodies with limited reactivity across the parasite life cycle. Here we sought to create antibodies that recognize novel epitopes that could be used to define intracellular development. We identified a mouse epithelial cell line that supported C. parvum growth, enabling immunization of mice with infected cells to create a bank of monoclonal antibodies (MAbs) against intracellular parasite stages while avoiding the development of host-specific antibodies. From this bank, we identified 12 antibodies with a range of reactivities across the parasite life cycle. Importantly, we identified specific MAbs that can distinguish different life cycle stages, such as trophozoites, merozoites, type I versus II meronts, and macrogamonts. These MAbs provide valuable tools for the Cryptosporidium research community and will facilitate future investigation into parasite biology. IMPORTANCE Cryptosporidium is a protozoan parasite that causes gastrointestinal disease in humans and animals. Currently, there is a limited array of antibodies available against the parasite, which hinders imaging studies and makes it difficult to visualize the parasite life cycle in different culture systems. In order to alleviate this reagent gap, we created a library of novel antibodies against the intracellular life cycle stages of Cryptosporidium We identified antibodies that recognize specific life cycle stages in distinctive ways, enabling unambiguous description of the parasite life cycle. These MAbs will aid future investigation into Cryptosporidium biology and help illuminate growth differences between various culture platforms. Copyright © 2018 Wilke et al.

Using subjective expectations to forecast longevity: do survey respondents know something we don't know?

PubMed

Perozek, Maria

2008-02-01

Old-age mortality is notoriously difficult to predict because it requires not only an understanding of the process of senescence-which is influenced by genetic, environmental, and behavioral factors-but also a prediction of how these factors will evolve. In this paper I argue that individuals are uniquely qualified to predict their own mortality based on their own genetic background, as well as environmental and behavioral risk factors that are often known only to the individual. Given this private information, individuals form expectations about survival probabilities that may provide additional information to demographers and policymakers in their challenge to predict mortality. From expectations data from the 1992 Health and Retirement Study (HRS), I construct subjective, cohort life tables that are shown to predict the unusual direction of revisions to U.S. life expectancy by gender between 1992 and 2004: that is, for these cohorts, the Social Security Actuary (SSA) raised male life expectancy in 2004 and at the same lowered female life expectancy, narrowing the gender gap in longevity by 25% over this period. Further, although the subjective life expectancies for men appear to be roughly in line with the 2004 life tables, the subjective expectations of women suggest that female life expectancies estimated by the SSA might still be on the high side.

Integrating automated support for a software management cycle into the TAME system

NASA Technical Reports Server (NTRS)

Sunazuka, Toshihiko; Basili, Victor R.

1989-01-01

Software managers are interested in the quantitative management of software quality, cost and progress. An integrated software management methodology, which can be applied throughout the software life cycle for any number purposes, is required. The TAME (Tailoring A Measurement Environment) methodology is based on the improvement paradigm and the goal/question/metric (GQM) paradigm. This methodology helps generate a software engineering process and measurement environment based on the project characteristics. The SQMAR (software quality measurement and assurance technology) is a software quality metric system and methodology applied to the development processes. It is based on the feed forward control principle. Quality target setting is carried out before the plan-do-check-action activities are performed. These methodologies are integrated to realize goal oriented measurement, process control and visual management. A metric setting procedure based on the GQM paradigm, a management system called the software management cycle (SMC), and its application to a case study based on NASA/SEL data are discussed. The expected effects of SMC are quality improvement, managerial cost reduction, accumulation and reuse of experience, and a highly visual management reporting system.

Health-adjusted life expectancy in Canada.

PubMed

Bushnik, Tracey; Tjepkema, Michael; Martel, Laurent

2018-04-18

Over the past century, life expectancy at birth in Canada has risen substantially. However, these gains in the quantity of life say little about gains in the quality of life. Health-adjusted life expectancy (HALE), an indicator of quality of life, was estimated for the household and institutional populations combined every four years from 1994/1995 to 2015. Health status was measured by the Health Utilities Index Mark 3 instrument in two national population health surveys, and was used to adjust life expectancy. The percentage of the population living in health-related institutions was estimated based on the Census of Population. Attribute-deleted HALE was calculated to determine how various aspects of health status contributed to the differences between life expectancy and HALE. HALE has increased in Canada. Greater gains among males have narrowed the gap between males and females. The ratio of HALE to life expectancy changed little for males, and a marginal improvement was observed for females aged 65 or older. Mobility problems and pain, the latter mainly among females, accounted for an increased share of the burden of ill health over time. Exclusion of the institutional population significantly increased the estimates of HALE and yielded higher ratios of HALE to life expectancy. Although people are living longer, the share of years spent in good functional health has remained fairly constant. Data for both the household and institutional populations are necessary for a complete picture of health expectancy in Canada.

Modeling absolute differences in life expectancy with a censored skew-normal regression approach

PubMed Central

Clough-Gorr, Kerri; Zwahlen, Marcel

2015-01-01

Parameter estimates from commonly used multivariable parametric survival regression models do not directly quantify differences in years of life expectancy. Gaussian linear regression models give results in terms of absolute mean differences, but are not appropriate in modeling life expectancy, because in many situations time to death has a negative skewed distribution. A regression approach using a skew-normal distribution would be an alternative to parametric survival models in the modeling of life expectancy, because parameter estimates can be interpreted in terms of survival time differences while allowing for skewness of the distribution. In this paper we show how to use the skew-normal regression so that censored and left-truncated observations are accounted for. With this we model differences in life expectancy using data from the Swiss National Cohort Study and from official life expectancy estimates and compare the results with those derived from commonly used survival regression models. We conclude that a censored skew-normal survival regression approach for left-truncated observations can be used to model differences in life expectancy across covariates of interest. PMID:26339544

Impact of demographic change, socioeconomics, and health care resources on life expectancy in Cambodia, Laos, and Myanmar.

PubMed

Chan, Moon Fai; Taylor, Beverly Joan

2013-05-01

Demographic and socioeconomic changes and the availability of health care resources were collected to examine the impacts on life expectancy in Cambodia, Laos, and Myanmar. An ecological design collecting 29 years (1980-2008) data for three Southeast Asian countries. Life expectancy, demographics, socioeconomic status, and health care resources were collected. The structural equation model indicates that more available health care resources and socioeconomic advantages were more likely to increase life expectancy. By contrast, demographic change was more likely to increase life expectancy by way of health care resources. Results show that factors that had direct impacts on life expectancy in all three countries were socioeconomic status and health care resources. Demographic changes had an indirect influence on life expectancy via health care resources. These findings suggest that policymakers should be focusing on how to remove the barriers that impede access to health care services during economic downturns. In addition, how to increase preventive care for the populations that have less access to health care in communities. © 2012 Wiley Periodicals, Inc.

Educated Parents, Educated Children: Toward a Multiple Life Cycles Education Policy

ERIC Educational Resources Information Center

Sticht, Thomas G.

2010-01-01

Given the important intergenerational effects of parents' education level on the achievement of their children, education policies should shift from a focus on one life cycle to a focus on "multiple life cycles". Such a policy would explicitly recognize that adults transfer their educational achievements to the achievement of their…

Alternative Fuels Data Center

Science.gov Websites

specified volumes of renewable fuels according to the categories below. EISA established life cycle GHG demonstrate a 20% reduction in life cycle GHG emissions. Advanced Biofuel: Any fuel derived from cellulosic or categories may be used to meet this category. Fuels in this category must demonstrate a life cycle GHG

Learning, Unlearning and Relearning--Knowledge Life Cycles in Library and Information Science Education

ERIC Educational Resources Information Center

Bedford, Denise A. D.

2015-01-01

The knowledge life cycle is applied to two core capabilities of library and information science (LIS) education--teaching, and research and development. The knowledge claim validation, invalidation and integration steps of the knowledge life cycle are translated to learning, unlearning and relearning processes. Mixed methods are used to determine…

Life Cycle Assessment Harmonization | Energy Analysis | NREL

Science.gov Websites

change are excluded from this analysis. The data showed that life cycle greenhouse gas (GHG) emissions Sensitivity Analysis of Biopower Life-Cycle Assessments and Greenhouse Gas Emission, Electric Power Research hydropower, ocean, geothermal, biopower, solar, wind, nuclear, coal, and natural gas technologies. See the

Modeling and Measuring Organization Capital

ERIC Educational Resources Information Center

Atkeson, Andrew; Kehoe, Patrick J.

2005-01-01

Manufacturing plants have a clear life cycle: they are born small, grow substantially with age, and eventually die. Economists have long thought that this life cycle is driven by organization capital, the accumulation of plant-specific knowledge. The location of plants in the life cycle determines the size of the payments, or organization rents,…

Toward Automated Inventory Modeling in Life Cycle Assessment: The Utility of Semantic Data Modeling to Predict Real-WorldChemical Production

EPA Science Inventory

A set of coupled semantic data models, i.e., ontologies, are presented to advance a methodology towards automated inventory modeling of chemical manufacturing in life cycle assessment. The cradle-to-gate life cycle inventory for chemical manufacturing is a detailed collection of ...

Coupling Computer-Aided Process Simulation and Estimations of Emissions and Land Use for Rapid Life Cycle Inventory Modeling

EPA Science Inventory

A methodology is described for developing a gate-to-gate life cycle inventory (LCI) of a chemical manufacturing process to support the application of life cycle assessment in the design and regulation of sustainable chemicals. The inventories were derived by first applying proces...

77 FR 40253 - Reserve Account

Federal Register 2010, 2011, 2012, 2013, 2014

2012-07-09

... Agency does not have a general formula that is used for the life cycle cost analysis. The life cycle cost... analysis is defined in 7 CFR 3560.11. The Agency reviews the results of the life cycle cost analysis for... cost analysis. The Agency agrees that the reserve accounts based on a percentage can be underfunded and...

Bypass control valve seal and bearing life cycle test report

NASA Technical Reports Server (NTRS)

Lundback, A. V.

1972-01-01

The operating characteristics of a bypass control valve seal and bearing life cycle tests are reported. Data from the initial assembly, leak, torque, and deflection tests are included along with the cycle life test results and conclusions. The equipment involved was to be used in the nuclear engine for the rocket vehicles program.

System Support/Sustainment Plan Platform for the Defense Enterprise Accounting Management System (DEAMS)

DTIC Science & Technology

2006-12-01

warfighters requirements and identifies system performance short-comings over its life cycle. 15. NUMBER OF PAGES 89 14. SUBJECT TERMS Information...the system performs to warfighters requirements and identifies system performance short-comings over its life cycle. vi...3 II. DEFENSE ACQUISITION LIFE CYCLE CURRENT STAGE ANALYSIS.......5 A. INTRODUCTION

75 FR 8272 - Defense Federal Acquisition Regulation Supplement; Acquisition Strategies To Ensure Competition...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-02-24

... Competition Throughout the Life Cycle of Major Defense Acquisition Programs AGENCY: Defense Acquisition... subcontract level of the MDAP throughout its life cycle as a means to improve contractor performance; and (2...) throughout the program life cycle as a means to improve contractor performance; and (ii) Document the...