Simple Experiments in Psychology.

ERIC Educational Resources Information Center

Ray, Wilbert S.

This material, developed for use in secondary schools, is a programmed-type learning package consisting of an "Instructor's Manual", a "Student's Introduction", and a "Laboratory Manual". The general goal of the program is to teach students to distinguish between reliable and unreliable information. The "Laboratory Manual" contains nine simple…

Nuclear particle detection using a track-recording solid

NASA Technical Reports Server (NTRS)

Weber, M.; Weber, D.

1984-01-01

The design of the nuclear particle detector located in Purdue University's Get Away Special package which was flown aboard STS-7 is detailed. The experiment consisted of a stack of particle-detecting polymer sheets. The sheets show positive results of tracks throughout the block. A slide of each sheet was made for further analysis. Recommendations for similar experiments performed in the future are discussed.

Packaged microsphere-taper coupling system with a high Q factor.

PubMed

Dong, Yongchao; Wang, Keyi; Jin, Xueying

2015-01-10

A novel packaged microsphere-taper coupling system which consists of a glass tube and two glass plates is proposed and demonstrated in this paper. We analyze the impact of the microsphere distortion on the resonant spectrum and it is observed that a very high quality factor (Q) up to 1.08×10(8) can be achieved by optimizing the microsphere position and orientation relative to the fiber taper. The maintenance of Q and a stable spectrum are realized by placing the packaged structure in a sealed organic glass box. Furthermore, to verify the practicability of the sealed device, thermal sensing experiments are carried out, which indicates the excellent convenience of the device with a resolution of 1.12×10(-4)°C. The portability and robustness of the packaged structure make it strikingly attractive and illustrate its potential in practical microcavity sensors and lasers.

The Raid distributed database system

NASA Technical Reports Server (NTRS)

Bhargava, Bharat; Riedl, John

1989-01-01

Raid, a robust and adaptable distributed database system for transaction processing (TP), is described. Raid is a message-passing system, with server processes on each site to manage concurrent processing, consistent replicated copies during site failures, and atomic distributed commitment. A high-level layered communications package provides a clean location-independent interface between servers. The latest design of the package delivers messages via shared memory in a configuration with several servers linked into a single process. Raid provides the infrastructure to investigate various methods for supporting reliable distributed TP. Measurements on TP and server CPU time are presented, along with data from experiments on communications software, consistent replicated copy control during site failures, and concurrent distributed checkpointing. A software tool for evaluating the implementation of TP algorithms in an operating-system kernel is proposed.

HOME for STEPS. Homemaking Opportunity Modules for Education for Use with Surviving Today's Experiences and Problems Successfully. Compiled from Competency Based Modules Based on V-TECS Catalogs.

ERIC Educational Resources Information Center

Marshall Univ., Huntington, WV. Dept. of Home Economics.

Designed to accompany Surviving Today's Experiences and Problems Successfully (STEPS) for 9th and 10th grade home economics courses, this volume consists of individualized learning packages dealing with four areas: management/family economics, human development, housing, and foods/nutrition. The book is divided into four parts. First, the…

An experiment with interactive planning models

NASA Technical Reports Server (NTRS)

Beville, J.; Wagner, J. H.; Zannetos, Z. S.

1970-01-01

Experiments on decision making in planning problems are described. Executives were tested in dealing with capital investments and competitive pricing decisions under conditions of uncertainty. A software package, the interactive risk analysis model system, was developed, and two controlled experiments were conducted. It is concluded that planning models can aid management, and predicted uses of the models are as a central tool, as an educational tool, to improve consistency in decision making, to improve communications, and as a tool for consensus decision making.

Automated analysis of biological oscillator models using mode decomposition.

PubMed

Konopka, Tomasz

2011-04-01

Oscillating signals produced by biological systems have shapes, described by their Fourier spectra, that can potentially reveal the mechanisms that generate them. Extracting this information from measured signals is interesting for the validation of theoretical models, discovery and classification of interaction types, and for optimal experiment design. An automated workflow is described for the analysis of oscillating signals. A software package is developed to match signal shapes to hundreds of a priori viable model structures defined by a class of first-order differential equations. The package computes parameter values for each model by exploiting the mode decomposition of oscillating signals and formulating the matching problem in terms of systems of simultaneous polynomial equations. On the basis of the computed parameter values, the software returns a list of models consistent with the data. In validation tests with synthetic datasets, it not only shortlists those model structures used to generate the data but also shows that excellent fits can sometimes be achieved with alternative equations. The listing of all consistent equations is indicative of how further invalidation might be achieved with additional information. When applied to data from a microarray experiment on mice, the procedure finds several candidate model structures to describe interactions related to the circadian rhythm. This shows that experimental data on oscillators is indeed rich in information about gene regulation mechanisms. The software package is available at http://babylone.ulb.ac.be/autoosc/.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Trentadue, R.; Clemencic, M.; Dykstra, D.

The LCG Persistency Framework consists of three software packages (CORAL, COOL and POOL) that address the data access requirements of the LHC experiments in several different areas. The project is the result of the collaboration between the CERN IT Department and the three experiments (ATLAS, CMS and LHCb) that are using some or all of the Persistency Framework components to access their data. POOL is a hybrid technology store for C++ objects, using a mixture of streaming and relational technologies to implement both object persistency and object metadata catalogs and collections. CORAL is an abstraction layer with an SQL-free APImore » for accessing data stored using relational database technologies. COOL provides specific software components and tools for the handling of the time variation and versioning of the experiment conditions data. This presentation reports on the status and outlook in each of the three sub-projects at the time of the CHEP2012 conference, reviewing the usage of each package in the three LHC experiments.« less

Search and Recovery Efforts for the ALSEP Data Tapes

NASA Technical Reports Server (NTRS)

Nagihara, S.; Nakamura, Y.; Lewis, L. R.; Williams, D. R.; Taylor, P. T.; Grayzeck, E. J.; Chi, P.; Schmidt, G. K.

2011-01-01

On NASA's first human lunar landing on Apollo II in July 1969, the astronauts deployed a set of scientific instruments called Early Apollo Science Experiments Package (EASEP). It was powered by a solar panel and operated for -20 earth-days and transmitted data to the Earth. This paved a way for deployment of more expansive instrument packages, powered by radioisotope thermoelectric generators, on Apollo 12, 14, 15, 16, and 17 in November 1969 through December 1972. They were called Apollo Lunar Surface Experiments Packages (ALSEPs). Each ALSEP consisted of a variety of instruments such as seismometers, magnetometers, solar wind spectrometers, heat flow probes, etc. The majority of these instruments kept functioning long after their one-year design lifetime requirement, and they transmitted data to the Earth until September 1977, when the program ended. Over the three decades that followed, users of the NSSDC-archived data have learned that many of the ALSEP instrument data are not complete. The present work is a progress report on the authors' recent effort for restoring the entire raw ALSEP data that were received from the Moon,

49 CFR 178.905 - Large Packaging identification codes.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Large Packaging identification codes. 178.905... FOR PACKAGINGS Large Packagings Standards § 178.905 Large Packaging identification codes. Large packaging code designations consist of: two numerals specified in paragraph (a) of this section; followed by...

GE781: a Monte Carlo package for fixed target experiments

NASA Astrophysics Data System (ADS)

Davidenko, G.; Funk, M. A.; Kim, V.; Kuropatkin, N.; Kurshetsov, V.; Molchanov, V.; Rud, S.; Stutte, L.; Verebryusov, V.; Zukanovich Funchal, R.

The Monte Carlo package for the fixed target experiment B781 at Fermilab, a third generation charmed baryon experiment, is described. This package is based on GEANT 3.21, ADAMO database and DAFT input/output routines.

Development Unit Configuration and Current Status of the MIP/MAAC Experiment

NASA Technical Reports Server (NTRS)

Karlmann, P. B.; Johnson, K. R.; Rapp, D.; Wu, J. J.

1999-01-01

The Mars In-Situ Propellant Production (ISPP) Precursor (MIP) experiment package is planned for inclusion on the Mars 2001 Lander. This experiment package consists of five experiments whose purpose is to demonstrate the performance of various ISPP processes in-situ on Mars. The demonstrated ability to produce propellant for Mars Return Vehicles (MRV) is considered to be a necessary precursor to any future manned mission to Mars. The Mars Atmosphere Acquisition and Compression (MAAC) experiment is part of the MIP package and is intended to demonstrate that, by using a sorption compressor, CO2 can be preferentially adsorbed at about 6 torr from the Mars atmosphere during the night when the bed is cold then subsequently compressed to about 800 torr by heating the bed and desorbing CO2 during the day. The compressed CO2 produced by MAAC is to be fed to the Oxygen Generator Subsystem (OGS) where pure oxygen is to be produced. Pure oxygen is considered to be one of the primary constituents of a future manned MRV propellant system. A MAAC Development Unit (DU) has been fabricated and tested at JPL. The MAAC DU consists of 1) a sorption bed filled with a CO2 selective sorbent material, 2) a purge system to be used to periodically backflush non-CO2 gases from the sorbent bed during adsorption, 3) a JPL-developed gas-gap heat switch that allows heat transfer to a radiator for heat removal from the bed during the night time adsorption period and that impedes heat transfer during the day time desorption period, 4) a radiator to radiate heat to the night sky during the adsorption period, 5) a set of three isolation valves and connecting tubing. 6) two pressure transducers and several thermocouples for monitoring the MAAC operating conditions, and command and data handling electronics. This paper will describe the operational theory and the configuration of the MAAC DU and will discuss the current status of the MAAC experiment development including some selected results of performance testing that has been completed prior to the ISRU III meeting.

Development Unit Configuration Status of the MIP/MAAC Experiment

NASA Technical Reports Server (NTRS)

Karlmann, P. B.; Johnson, K. R.; Rapp, D.; Wu, J. J.

1999-01-01

The Mars In-Situ Propellant Production (ISPP) Precursor (MIP) experiment package is planned for inclusion on the Mars 2001 Lander. This experiment package consists of five experiments whose purpose is to demonstrate the performance of various ISPP processes in-situ on Mars. The demonstrated ability to produce propellant for Mars Return Vehicles (MRV) is considered to be a necessary precursor to any future manned mission to Mars. The Mars Atmosphere Acquisition and Compression (MAAC) experiment is part of the MIP package and is intended to demonstrate that, by using a sorption compressor, CO2 can be preferentially adsorbed at about 6 torr from the Mars atmosphere during the night when the bed is cold then subsequently compressed to about 800 torr by heating the bed and desorbing C02 during the day. The compressed CO2 produced by MAAC is to be fed to the Oxygen Generator Subsystem (OGS) where pure oxygen is to be produced. Pure oxygen is considered to be one of the primary constituents of a future manned MRV propellant system. A MAAC Development Unit (DU) has been fabricated and tested at JPL. The MAAC DU consists of: (1) a sorption bed filled with a CO2 selective sorbent material; (2) a purge system to be used to periodically backflush non-CO2 gases from the sorbent bed during adsorption; (3) a JPL-developed gas-gap heat switch that allows heat transfer to a radiator for heat removal from the bed during the night time adsorption period and that impedes heat transfer during the day time desorption period; (4) a radiator to radiate heat to the night sky during the adsorption period; (5) a set of three isolation valves and connecting tubing; (6) two pressure transducers and several thermocouples for monitoring the MAAC operating conditions, and command and data handling electronics. This paper will describe the operational theory and the configuration of the MAAC DU and will discuss the current status of the MAAC experiment development including some selected results of performance testing that has been completed prior to the ISRU III meeting.

MicroSIFT Courseware Evaluations [Set 15 (362-388) and Set 16 (389-441), with an Index Listing the Contents of Each Set (Sets 1-16) and a Cumulative Subject Index (Sets 1-16)].

ERIC Educational Resources Information Center

Northwest Regional Educational Lab., Portland, OR.

This document consists of 80 microcomputer software package evaluations prepared by the MicroSIFT (Microcomputer Software and Information for Teachers) Clearinghouse at the Northwest Regional Education Laboratory. Set 15 consists of 27 packages; set 16 consists of 53 packages. Each software review lists producer, time and place of evaluation,…

10 CFR 60.143 - Monitoring and testing waste packages.

Code of Federal Regulations, 2010 CFR

2010-01-01

... package monitoring program shall include laboratory experiments which focus on the internal condition of... the laboratory experiments. (d) The waste package monitoring program shall continue as long as...

10 CFR 60.143 - Monitoring and testing waste packages.

Code of Federal Regulations, 2011 CFR

2011-01-01

... package monitoring program shall include laboratory experiments which focus on the internal condition of... the laboratory experiments. (d) The waste package monitoring program shall continue as long as...

10 CFR 60.143 - Monitoring and testing waste packages.

Code of Federal Regulations, 2012 CFR

2012-01-01

... package monitoring program shall include laboratory experiments which focus on the internal condition of... the laboratory experiments. (d) The waste package monitoring program shall continue as long as...

10 CFR 60.143 - Monitoring and testing waste packages.

Code of Federal Regulations, 2013 CFR

2013-01-01

... package monitoring program shall include laboratory experiments which focus on the internal condition of... the laboratory experiments. (d) The waste package monitoring program shall continue as long as...

10 CFR 60.143 - Monitoring and testing waste packages.

Code of Federal Regulations, 2014 CFR

2014-01-01

... package monitoring program shall include laboratory experiments which focus on the internal condition of... the laboratory experiments. (d) The waste package monitoring program shall continue as long as...

Design and Development of a CPCI-Based Electronics Package for Space Station Experiments

NASA Technical Reports Server (NTRS)

Kolacz, John S.; Clapper, Randy S.; Wade, Raymond P.

2006-01-01

The NASA John H. Glenn Research Center is developing a Compact-PCI (CPCI) based electronics package for controlling space experiment hardware on the International Space Station. Goals of this effort include an easily modified, modular design that allows for changes in experiment requirements. Unique aspects of the experiment package include a flexible circuit used for internal interconnections and a separate enclosure (box in a box) for controlling 1 kW of power for experiment fuel heating requirements. This electronics package was developed as part of the FEANICS (Flow Enclosure Accommodating Novel Investigations in Combustion of Solids) mini-facility which is part of the Fluids and Combustion Facility s Combustion Integrated Rack (CIR). The CIR will be the platform for future microgravity combustion experiments and will reside on the Destiny Module of the International Space Station (ISS). The FEANICS mini-facility will be the primary means for conducting solid fuel combustion experiments in the CIR on ISS. The main focus of many of these solid combustion experiments will be to conduct applied scientific investigations in fire-safety to support NASA s future space missions. A description of the electronics package and the results of functional testing are the subjects of this report. The report concludes that the use of innovative packaging methods combined with readily available COTS hardware can provide a modular electronics package which is easily modified for changing experiment requirements.

MicroSIFT Courseware Evaluations. [Set 11 (223-259), Set 12 (260-293), and a Special Set of 99 LIBRA Reviews of Junior High School Science Software, Including Subject and Title Indexes Covering Sets 1-12 and Special Set L].

ERIC Educational Resources Information Center

Northwest Regional Educational Lab., Portland, OR.

This document consists of 170 microcomputer software package evaluations prepared by the MicroSIFT (Microcomputer Software and Information for Teachers) Clearinghouse at the Northwest Regional Education Laboratory. Set 11 consists of 37 packages. Set 12 consists of 34 packages. A special unnumbered set, entitled LIBRA Reviews, treats 99 packages…

Closing the loop on improvement: Packaging experience in the Software Engineering Laboratory

NASA Technical Reports Server (NTRS)

Waligora, Sharon R.; Landis, Linda C.; Doland, Jerry T.

1994-01-01

As part of its award-winning software process improvement program, the Software Engineering Laboratory (SEL) has developed an effective method for packaging organizational best practices based on real project experience into useful handbooks and training courses. This paper shares the SEL's experience over the past 12 years creating and updating software process handbooks and training courses. It provides cost models and guidelines for successful experience packaging derived from SEL experience.

Practical fundamentals of glass, rubber, and plastic sterile packaging systems.

PubMed

Sacha, Gregory A; Saffell-Clemmer, Wendy; Abram, Karen; Akers, Michael J

2010-01-01

Sterile product packaging systems consist of glass, rubber, and plastic materials that are in intimate contact with the formulation. These materials can significantly affect the stability of the formulation. The interaction between the packaging materials and the formulation can also affect the appropriate delivery of the product. Therefore, a parenteral formulation actually consists of the packaging system as well as the product that it contains. However, the majority of formulation development time only considers the product that is contained in the packaging system. Little time is spent studying the interaction of the packaging materials with the contents. Interaction between the packaging and the contents only becomes a concern when problems are encountered. For this reason, there are few scientific publications that describe the available packaging materials, their advantages and disadvantages, and their important product attributes. This article was created as a reference for product development and describes some of the packaging materials and systems that are available for parenteral products.

Package Design Affects Accuracy Recognition for Medications.

PubMed

Endestad, Tor; Wortinger, Laura A; Madsen, Steinar; Hortemo, Sigurd

2016-12-01

Our aim was to test if highlighting and placement of substance name on medication package have the potential to reduce patient errors. An unintentional overdose of medication is a large health issue that might be linked to medication package design. In two experiments, placement, background color, and the active ingredient of generic medication packages were manipulated according to best human factors guidelines to reduce causes of labeling-related patient errors. In two experiments, we compared the original packaging with packages where we varied placement of the name, dose, and background of the active ingredient. Age-relevant differences and the effect of color on medication recognition error were tested. In Experiment 1, 59 volunteers (30 elderly and 29 young students), participated. In Experiment 2, 25 volunteers participated. The most common error was the inability to identify that two different packages contained the same active ingredient (young, 41%, and elderly, 68%). This kind of error decreased with the redesigned packages (young, 8%, and elderly, 16%). Confusion errors related to color design were reduced by two thirds in the redesigned packages compared with original generic medications. Prominent placement of substance name and dose with a band of high-contrast color support recognition of the active substance in medications. A simple modification including highlighting and placing the name of the active ingredient in the upper right-hand corner of the package helps users realize that two different packages can contain the same active substance, thus reducing the risk of inadvertent medication overdose. © 2016, Human Factors and Ergonomics Society.

Package Design Affects Accuracy Recognition for Medications

PubMed Central

Endestad, Tor; Wortinger, Laura A.; Madsen, Steinar; Hortemo, Sigurd

2016-01-01

Objective: Our aim was to test if highlighting and placement of substance name on medication package have the potential to reduce patient errors. Background: An unintentional overdose of medication is a large health issue that might be linked to medication package design. In two experiments, placement, background color, and the active ingredient of generic medication packages were manipulated according to best human factors guidelines to reduce causes of labeling-related patient errors. Method: In two experiments, we compared the original packaging with packages where we varied placement of the name, dose, and background of the active ingredient. Age-relevant differences and the effect of color on medication recognition error were tested. In Experiment 1, 59 volunteers (30 elderly and 29 young students), participated. In Experiment 2, 25 volunteers participated. Results: The most common error was the inability to identify that two different packages contained the same active ingredient (young, 41%, and elderly, 68%). This kind of error decreased with the redesigned packages (young, 8%, and elderly, 16%). Confusion errors related to color design were reduced by two thirds in the redesigned packages compared with original generic medications. Conclusion: Prominent placement of substance name and dose with a band of high-contrast color support recognition of the active substance in medications. Application: A simple modification including highlighting and placing the name of the active ingredient in the upper right-hand corner of the package helps users realize that two different packages can contain the same active substance, thus reducing the risk of inadvertent medication overdose. PMID:27591209

CRP - VD Tube & Closure -  Unit Non-Reclosable Packaging Rigid

EPA Pesticide Factsheets

This is a unit-dose non-reclosable rigid package. The package consists of a tube and a closure that is permanently attached to the tube neck. The package is opened by pushing down on the closure and simultaneously turning it counterclockwise.

UNIX-BASED DATA MANAGEMENT SYSTEM FOR PROPAGATION EXPERIMENTS

NASA Technical Reports Server (NTRS)

Kantak, A. V.

1994-01-01

This collection of programs comprises The UNIX Based Data Management System for the Pilot Field Experiment (PiFEx) which is an attempt to mimic the Mobile Satellite (MSAT) scenario. The major purposes of PiFEx are to define the mobile communications channels and test the workability of new concepts used to design various components of the receiver system. The results of the PiFex experiment are large amounts of raw data which must be accessed according to a researcher's needs. This package provides a system to manage the PiFEx data in an interactive way. The system not only provides the file handling necessary to retrieve the desired data, but also several FORTRAN programs to generate some standard results pertaining to propagation data. This package assumes that the data file initially generated from the experiment has been already converted from binary to ASCII format. The Data Management system described here consists of programs divided into two categories: those programs that handle the PiFEx generated files and those that are used for number-crunching of these files. Five FORTRAN programs and one UNIX shell script file are used for file manipulation purposes. These activities include: calibration of the acquired data; and parsing of the large data file into datasets concerned with different aspects of the experiment such as the specific calibrated propagation data, dynamic and static loop error data, statistical data, and temperature and spatial data on the hardware used in the experiment. The five remaining FORTRAN programs are used to generate usable information about the data. Signal level probability, probability density of the signal fitting the Rician density function, frequency of the data's fade duration, and the Fourier transform of the data can all be generated from these data manipulation programs. In addition, a program is provided which generates a downloadable file from the signal levels and signal phases files for use with the plotting routine AKPLOT (NPO-16931). All programs in this package are written in either FORTRAN-77 or UNIX shell-scripts. The package does not include test data. The programs were developed in 1987 for use with a UNIX operating system on a DEC MicroVAX computer.

Performance Results for Massachusetts and Rhode Island Deep Energy Retrofit Pilot Community

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gates, C.; Neuhauser, K.

2014-03-01

Between December, 2009 and December, 2012, 42 deep energy retrofit (DER) projects were completed through a pilot program sponsored by National Grid and conducted in Massachusetts and Rhode Island. Thirty-seven of these projects were comprehensive retrofits while five were partial DERs, meaning that high performance retrofit was implemented for a single major enclosure component or a limited number of major enclosure components. Building Science Corporation developed a consistent "package" of measures in terms of the performance targeted for major building components. Based on the community experience, this DER package is expected to result in yearly source energy use near 110more » MMBtu/year or approximately 40% below the Northeast regional average.« less

[Microcomputer control of a LED stimulus display device].

PubMed

Ohmoto, S; Kikuchi, T; Kumada, T

1987-02-01

A visual stimulus display system controlled by a microcomputer was constructed at low cost. The system consists of a LED stimulus display device, a microcomputer, two interface boards, a pointing device (a "mouse") and two kinds of software. The first software package is written in BASIC. Its functions are: to construct stimulus patterns using the mouse, to construct letter patterns (alphabet, digit, symbols and Japanese letters--kanji, hiragana, katakana), to modify the patterns, to store the patterns on a floppy disc, to translate the patterns into integer data which are used to display the patterns in the second software. The second software package, written in BASIC and machine language, controls display of a sequence of stimulus patterns in predetermined time schedules in visual experiments.

A comparison of InVivoStat with other statistical software packages for analysis of data generated from animal experiments.

PubMed

Clark, Robin A; Shoaib, Mohammed; Hewitt, Katherine N; Stanford, S Clare; Bate, Simon T

2012-08-01

InVivoStat is a free-to-use statistical software package for analysis of data generated from animal experiments. The package is designed specifically for researchers in the behavioural sciences, where exploiting the experimental design is crucial for reliable statistical analyses. This paper compares the analysis of three experiments conducted using InVivoStat with other widely used statistical packages: SPSS (V19), PRISM (V5), UniStat (V5.6) and Statistica (V9). We show that InVivoStat provides results that are similar to those from the other packages and, in some cases, are more advanced. This investigation provides evidence of further validation of InVivoStat and should strengthen users' confidence in this new software package.

Comparison between Measured and Simulated Radiation Doses in the Matoroshka-R Spherical phantom Experiment#1 and Area Monitoring aboard International Space Station using PADLES from May - Sep. 2012

NASA Astrophysics Data System (ADS)

Nagamatsu, Aiko; Tolochek, Raisa; Shurshakov, Vyacheslav; Nikolaev, Igor; Tawara, Hiroko; Kitajo, Keiichi; Shimada, Ken

The measurement of radiation environmental parameters in space is essential to support radiation risk assessments for astronauts and establish a benchmark for space radiation models for present and future human space activities. Since Japanese Experiment Module ‘KIBO’ was attached to the International Space Station (ISS) in 2008, we have been performing continuous space radiation dosimetery using a PADLES (Passive Dosimeter for Life-Science Experiments in Space) consisting of CR-39 PNTDs (Plastic Nuclear track detectors) and TLD-MSOs (Mg2SiO4:Tb) for various space experiments onboard the ‘KIBO’ part of the ISS. The MATROSHKA-R experiments aims to verify of dose distributions in a human body during space flight. The phantom consists of tissue equivalent material covered by a poncho jacket with 32 pockets on the surface. 20 container rods with dosimeters can be struck into the spherical phantom. Its diameter is 370 mm and it is 32 kg in weight. The first experiment onboard the KIBO at Forward No.2 area (JPM1F2 Rack2) was conducted over 114 days from 21 May to 12 September 2012 (the installation schedule inside the phantom) on the way to solar cycle 24th upward curve. 16 PADLES packages were deployed into 16 poncho pockets on the surface of the spherical phantom. Another 12 PADLES packages were deployed inside 4 rods (3 packages per rod in the outer, middle and inner side). Area monitoring in the KIBO was conducted in the same period (Area PADLES series #8 from 15 May to 16 September, 2012). Absorbed doses were measured at 17 area monitoring points in the KIBO and 28 locations (16 packages in poncho pockets and 12 inside 4 rods) in the phantom. The maximum value measured with the PADLES in the poncho pockets on the surface of the spherical phantom facing the outer wall was 0.43 mGy/day and the minimum value measured with the PADLES in the poncho pockets on the surface of the spherical phantom facing the KIBO interior was 0.30 mGy/day. The maximum absorbed doses measured inside rods was 0.28 mGy/day and the minimum value was 0.19 mGy/day. This indicates doses measured from the dosimeters placed in the outer side of each rod are relatively high compared to the doses placed in the center of rod. At this time, we also would like to show the preliminary results of comparative study between measured and Simulated Radiation Doses using the Particle and Heavy Ion Transport code System (PHITS) calculations with well developed shielding model of the KIBO and numerical spherical phantom inside.

A communication skills intervention for community healthcare workers reduces perceived patient aggression: a pretest-postest study.

PubMed

Swain, Nicola; Gale, Christopher

2014-09-01

Previous studies have shown that healthcare workers experience high levels of aggression from patients. Prevention packages to address this have received little research support. Communication skills have been shown to influence individuals' experience of aggression and are also amenable to training. This study aims to deliver a communication skills training package that will reduce the experience of aggression in the workplace for healthcare workers. An interactive, multimedia communication skills package was developed that would be suitable for community healthcare workers. The training consisted of four workshops, including teaching, discussion and DVD illustrative examples. These were based on research and clinical experience. This intervention was delivered in two community care organisations over several months. Fifty-six community healthcare workers took part in the trial in small groups. There were 46 females and 10 males with a median age of 45-54 years. For each group a series of four communication skills workshops were given. Measurements of perceived aggression and wellbeing were taken before the workshops, at the end of the workshops, one month after and two months after. Results show statistically significant reductions in perceived aggression one and two months after baseline measures (p<0.01). Results also suggest reductions in distress and increases in general mental wellness (p<0.01). Evaluation of the programme by participants was positive. A brief communication skills training programme is both enjoyable and shows decreases in perceived aggression, distress, and increases in general mental wellness. A full RCT of this intervention is warranted. Copyright © 2014 Elsevier Ltd. All rights reserved.

Evaluating Dense 3d Reconstruction Software Packages for Oblique Monitoring of Crop Canopy Surface

NASA Astrophysics Data System (ADS)

Brocks, S.; Bareth, G.

2016-06-01

Crop Surface Models (CSMs) are 2.5D raster surfaces representing absolute plant canopy height. Using multiple CMSs generated from data acquired at multiple time steps, a crop surface monitoring is enabled. This makes it possible to monitor crop growth over time and can be used for monitoring in-field crop growth variability which is useful in the context of high-throughput phenotyping. This study aims to evaluate several software packages for dense 3D reconstruction from multiple overlapping RGB images on field and plot-scale. A summer barley field experiment located at the Campus Klein-Altendorf of University of Bonn was observed by acquiring stereo images from an oblique angle using consumer-grade smart cameras. Two such cameras were mounted at an elevation of 10 m and acquired images for a period of two months during the growing period of 2014. The field experiment consisted of nine barley cultivars that were cultivated in multiple repetitions and nitrogen treatments. Manual plant height measurements were carried out at four dates during the observation period. The software packages Agisoft PhotoScan, VisualSfM with CMVS/PMVS2 and SURE are investigated. The point clouds are georeferenced through a set of ground control points. Where adequate results are reached, a statistical analysis is performed.

Experimental comparison of forces resisting viral DNA packaging and driving DNA ejection

PubMed Central

Keller, Nicholas; Berndsen, Zachary T.; Jardine, Paul J.; Smith, Douglas E.

2018-01-01

We compare forces resisting DNA packaging in bacteriophage phi29 inferred from optical tweezers studies with forces driving DNA ejection inferred from osmotic pressure studies. Ejection forces from 0–80% filling are consistent with a model that assumes a repulsive DNA-DNA interaction potential derived from DNA condensation studies and predicts an inverse spool DNA conformation. Forces resisting packaging from ~80–100% filling are also consistent with this model. However, that electron microscopy does not reveal a spool conformation suggests that this model overestimates bending rigidity and underestimates repulsion. Below 80% filling, inferred ejection forces are higher than those resisting packaging. Although unexpected, this suggests that most force that builds during packaging is available to drive DNA ejection. PMID:28618627

Creative Thinking Package

ERIC Educational Resources Information Center

Jones, Clive

1972-01-01

A look at the latest package from a British managment training organization, which explains and demonstrates creative thinking techniques, including brainstorming. The package, designed for groups of twelve or more, consists of tapes, visuals, and associated exercises. (Editor/JB)

Database of proposed payloads and instruments for SEI missions

NASA Technical Reports Server (NTRS)

Barlow, N. G.

1992-01-01

A database of all payloads and instruments proposed for lunar and Mars missions was compiled by the author for the Exploration Programs Office at NASA's Johnson Sapce Center. The database is an outgrowth of the document produced by C. J. Budney et al. at the Jet Propulsion Laboratory in 1991. The present database consists not only of payloads proposed for human exploratory missions of the Moon and Mars, but also experiments selected or proposed for robotic precursor missions such as Lunar Scout, Mars Observer, and MESUR. The database consists of two parts: a written payload description and a matrix that provides a breakdown of payload components. Each payload description consists of the following information: (1) the rationale for why the instrument or payload package is being proposed for operation on the Moon or Mars; (2) a description of how the instrument works; (3) a breakdown of the payload, providing detailed information about the mass, volume, power requirements, and data rates for the constituent pieces of the experiment; (4) estimates of the power consumption and data rate; (5) how the data will be returned to Earth and distributed to the scientific community; (6) any constraints on the location or conditions under which the instrument can or cannot operate; (7) what type of crew interaction (if any) is needed; (8) how the payload is to be delivered to the lunar or martian surface (along with alternative delivery options); (9) how long the instrument or payload package will take to set up; (10) what type of maintenance needs are anticipated for the experiment; (11) stage of development for the instrument and environmental conditions under which the instrument has been tested; (12) an interface required by the instrument with the lander, a rover, an outpost, etc.; (13) information about how often the experiment will need to be resupplied with parts or consumables, if it is to be resupplied; (14) the name and affiliation of a contact person for the experiment; and (15) references where further information about the experiment can be found.

Solar Mesosphere Explorer

NASA Technical Reports Server (NTRS)

1981-01-01

Five experiments and the instruments packages designed for use in studying reactions between sunlight, ozone, and other chemicals in the atmosphere as well as for determining how ozone concentrations are transported in the mesosphere are described. The spin-stabilized satellite carrying the experiments consists of an observatory module and a spacecraft bus. Powered by a solar array which charges the nickel-cadmium batteries, the satellite is to be inserted into a sun synchronous orbit by a two stage Delta 2310 launch vehicle. The mission objectives, spacecraft configurations, and various subsystems are described as well as the ground support and prelaunch operations.

Developing targets for radiation transport experiments at the Omega laser facility

DOE PAGES

Capelli, Deanna; Charsley-Groffman, C. A.; Randolph, Randall Blaine; ...

2017-07-13

Targets have been developed to measure supersonic radiation transport in aerogel foams using absorption spectroscopy. The target consists of an aerogel foam uniformly doped with either titanium or scandium inserted into an undoped aerogel foam package. This creates a localized doped foam region to provide spatial resolution for the measurement. Development and characterization of the foams is a key challenge in addition to machining and assembling the two foams so they mate without gaps. The foam package is inserted into a beryllium sleeve and mounted on a gold hohlraum. The target is mounted to a holder created using additive manufacturingmore » and mounted on a stalk. As a result, the manufacturing of the components, along with assembly and metrology of the target are described here.« less

Developing targets for radiation transport experiments at the Omega laser facility

DOE Office of Scientific and Technical Information (OSTI.GOV)

Capelli, Deanna; Charsley-Groffman, C. A.; Randolph, Randall Blaine

Targets have been developed to measure supersonic radiation transport in aerogel foams using absorption spectroscopy. The target consists of an aerogel foam uniformly doped with either titanium or scandium inserted into an undoped aerogel foam package. This creates a localized doped foam region to provide spatial resolution for the measurement. Development and characterization of the foams is a key challenge in addition to machining and assembling the two foams so they mate without gaps. The foam package is inserted into a beryllium sleeve and mounted on a gold hohlraum. The target is mounted to a holder created using additive manufacturingmore » and mounted on a stalk. As a result, the manufacturing of the components, along with assembly and metrology of the target are described here.« less

Large Scale Software Building with CMake in ATLAS

NASA Astrophysics Data System (ADS)

Elmsheuser, J.; Krasznahorkay, A.; Obreshkov, E.; Undrus, A.; ATLAS Collaboration

2017-10-01

The offline software of the ATLAS experiment at the Large Hadron Collider (LHC) serves as the platform for detector data reconstruction, simulation and analysis. It is also used in the detector’s trigger system to select LHC collision events during data taking. The ATLAS offline software consists of several million lines of C++ and Python code organized in a modular design of more than 2000 specialized packages. Because of different workflows, many stable numbered releases are in parallel production use. To accommodate specific workflow requests, software patches with modified libraries are distributed on top of existing software releases on a daily basis. The different ATLAS software applications also require a flexible build system that strongly supports unit and integration tests. Within the last year this build system was migrated to CMake. A CMake configuration has been developed that allows one to easily set up and build the above mentioned software packages. This also makes it possible to develop and test new and modified packages on top of existing releases. The system also allows one to detect and execute partial rebuilds of the release based on single package changes. The build system makes use of CPack for building RPM packages out of the software releases, and CTest for running unit and integration tests. We report on the migration and integration of the ATLAS software to CMake and show working examples of this large scale project in production.

Wide-Field Imaging Telescope-0 (WIT0) with automatic observing system

NASA Astrophysics Data System (ADS)

Ji, Tae-Geun; Byeon, Seoyeon; Lee, Hye-In; Park, Woojin; Lee, Sang-Yun; Hwang, Sungyong; Choi, Changsu; Gibson, Coyne Andrew; Kuehne, John W.; Prochaska, Travis; Marshall, Jennifer L.; Im, Myungshin; Pak, Soojong

2018-01-01

We introduce Wide-Field Imaging Telescope-0 (WIT0), with an automatic observing system. It is developed for monitoring the variabilities of many sources at a time, e.g. young stellar objects and active galactic nuclei. It can also find the locations of transient sources such as a supernova or gamma-ray bursts. In 2017 February, we installed the wide-field 10-inch telescope (Takahashi CCA-250) as a piggyback system on the 30-inch telescope at the McDonald Observatory in Texas, US. The 10-inch telescope has a 2.35 × 2.35 deg field-of-view with a 4k × 4k CCD Camera (FLI ML16803). To improve the observational efficiency of the system, we developed a new automatic observing software, KAOS30 (KHU Automatic Observing Software for McDonald 30-inch telescope), which was developed by Visual C++ on the basis of a windows operating system. The software consists of four control packages: the Telescope Control Package (TCP), the Data Acquisition Package (DAP), the Auto Focus Package (AFP), and the Script Mode Package (SMP). Since it also supports the instruments that are using the ASCOM driver, the additional hardware installations become quite simplified. We commissioned KAOS30 in 2017 August and are in the process of testing. Based on the WIT0 experiences, we will extend KAOS30 to control multiple telescopes in future projects.

Mechanical Design and Development of TES Bolometer Detector Arrays for the Advanced ACTPol Experiment

NASA Technical Reports Server (NTRS)

Ward, Jonathan T.; Austermann, Jason; Beall, James A.; Choi, Steve K.; Crowley, Kevin T.; Devlin, Mark J.; Duff, Shannon M.; Gallardo, Patricio M.; Henderson, Shawn W.; Ho, Shuay-Pwu Patty;

Mechanical designs and development of TES bolometer detector arrays for the Advanced ACTPol experiment

NASA Astrophysics Data System (ADS)

Ward, Jonathan T.; Austermann, Jason; Beall, James A.; Choi, Steve K.; Crowley, Kevin T.; Devlin, Mark J.; Duff, Shannon M.; Gallardo, Patricio A.; Henderson, Shawn W.; Ho, Shuay-Pwu Patty; Hilton, Gene; Hubmayr, Johannes; Khavari, Niloufar; Klein, Jeffrey; Koopman, Brian J.; Li, Dale; McMahon, Jeffrey; Mumby, Grace; Nati, Federico; Niemack, Michael D.; Page, Lyman A.; Salatino, Maria; Schillaci, Alessandro; Schmitt, Benjamin L.; Simon, Sara M.; Staggs, Suzanne T.; Thornton, Robert; Ullom, Joel N.; Vavagiakis, Eve M.; Wollack, Edward J.

2016-07-01

The next generation Advanced ACTPol (AdvACT) experiment is currently underway and will consist of four Transition Edge Sensor (TES) bolometer arrays, with three operating together, totaling 5800 detectors on the sky. Building on experience gained with the ACTPol detector arrays, AdvACT will utilize various new technologies, including 150 mm detector wafers equipped with multichroic pixels, allowing for a more densely packed focal plane. Each set of detectors includes a feedhorn array of stacked silicon wafers which form a spline profile leading to each pixel. This is then followed by a waveguide interface plate, detector wafer, back short cavity plate, and backshort cap. Each array is housed in a custom designed structure manufactured from high purity copper and then gold plated. In addition to the detector array assembly, the array package also encloses cryogenic readout electronics. We present the full mechanical design of the AdvACT high frequency (HF) detector array package along with a detailed look at the detector array stack assemblies. This experiment will also make use of extensive hardware and software previously developed for ACT, which will be modified to incorporate the new AdvACT instruments. Therefore, we discuss the integration of all AdvACT arrays with pre-existing ACTPol infrastructure.

Online Event Reconstruction in the CBM Experiment at FAIR

NASA Astrophysics Data System (ADS)

Akishina, Valentina; Kisel, Ivan

2018-02-01

Targeting for rare observables, the CBM experiment will operate at high interaction rates of up to 10 MHz, which is unprecedented in heavy-ion experiments so far. It requires a novel free-streaming readout system and a new concept of data processing. The huge data rates of the CBM experiment will be reduced online to the recordable rate before saving the data to the mass storage. Full collision reconstruction and selection will be performed online in a dedicated processor farm. In order to make an efficient event selection online a clean sample of particles has to be provided by the reconstruction package called First Level Event Selection (FLES). The FLES reconstruction and selection package consists of several modules: track finding, track fitting, event building, short-lived particles finding, and event selection. Since detector measurements contain also time information, the event building is done at all stages of the reconstruction process. The input data are distributed within the FLES farm in a form of time-slices. A time-slice is reconstructed in parallel between processor cores. After all tracks of the whole time-slice are found and fitted, they are collected into clusters of tracks originated from common primary vertices, which then are fitted, thus identifying the interaction points. Secondary tracks are associated with primary vertices according to their estimated production time. After that short-lived particles are found and the full event building process is finished. The last stage of the FLES package is a selection of events according to the requested trigger signatures. The event reconstruction procedure and the results of its application to simulated collisions in the CBM detector setup are presented and discussed in detail.

Programme on the recyclability of food-packaging materials with respect to food safety considerations: polyethylene terephthalate (PET), paper and board, and plastics covered by functional barriers.

PubMed

Franz, R

2002-01-01

Stimulated by new ecology-driven European and national regulations, news routes of recycling waste appear on the market. Since food packages represent a large percentage of the plastics consumption and since they have a short lifetime, an important approach consists in making new packages from post-consumer used packages. On the other hand, food-packaging regulations in Europe require that packaging materials must be safe. Therefore, potential mass transfer (migration) of harmful recycling-related substances to the food must be excluded and test methods to ensure the safety-in-use of recycled materials for food packaging are needled. As a consequence of this situation, a European research project FAIR-CT98-4318, with the acronym 'Recyclability', was initiated. The project consists of three sections each focusing on a different class of recycled materials: polyethylene terephthalate (PET), paper and board, and plastics covered by functional barriers. The project consortium consists of 28 project members from 11 EU countries. In addition, the project is during its lifetime in discussion with the US Food and Drug Administrations (FDA) to consider also US FDA regulatory viewpoints and to aim, as a consequence, to harmonizable conclusions and recommendations. The paper introduces the project and presents an overview of the project work progress.

Teaching preschool children to report suspicious packages to adults.

PubMed

May, Michael E; Shayter, Ashley M; Schmick, Ayla; Barron, Becky; Doherty, Meghan; Johnson, Matthew

2018-05-16

Law enforcement agencies stress that public reporting of terror-related crime is the predominant means for disrupting these actions. However, schools may be unprepared because the majority of the populace may not understand the threat of suspicious materials or what to do when they are found on school grounds. The purpose of this study was to systematically teach preschool children to identify and report suspicious packages across three experiments. In the first experiment, we used multiple exemplar training to teach children to identify the characteristics of safe and unsafe packages. In the second experiment, we taught participants to identify the locations where packages should be considered unsafe. Finally, in the third experiment, we used behavioral skills training to teach participants to avoid touching unsafe packages, leave the area where they were located, and report their discovery to an adult. Results suggest the participants quickly developed these skills. Implications for safety skills in young school children are discussed. © 2018 Society for the Experimental Analysis of Behavior.

Apollo 17 Lunar Surface Experiments package

NASA Image and Video Library

1972-05-10

S72-37260 (November 1972) --- The remote antenna for the Lunar Seismic Profiling Experiment, Numbered S-203, a component of the Apollo Lunar Surface Experiments Package which will be carried on the Apollo 17 lunar landing mission. LSPE components are four geophones similar to those used in earlier active seismic experiments an electronics package in the ALSEP central station, and eight explosive packages which will be deployed during the geology traverse. The four geophones will be placed one in the center and at each corner of a 90-meter equilateral triangle. Explosive charges placed on the surface will generate seismic waves of varying strengths to provide data on the structural profile of the landing site. After the charges have been fired by ground command, the experiment will settle down into a passive listening mode, detecting moonquakes, meteorite impacts and the thump caused by the Lunar Module ascent stage impact. The antenna is of the telescoping type.

Young adult smokers' perceptions of plain packaging: a pilot naturalistic study.

PubMed

Moodie, Crawford; Mackintosh, Anne Marie; Hastings, Gerard; Ford, Allison

2011-09-01

To explore the impact, if any, that using plain (non-branded) cigarette packs in real-life settings has on young adult smokers. Naturalistic-type research was employed, where smokers used brown 'plain' packs for 2 weeks and their regular packs for 2 weeks, in real-life settings. Participants were recruited in Glasgow, Scotland. Of the 140 smokers aged 18-35 years who participated in the naturalistic study, 48 correctly completed and returned all questionnaires. Over the 4-week study period, participants completed a questionnaire twice a week assessing pack perceptions and feelings, feelings about smoking, salience of health warnings and smoking-related behaviours. A subsample of 18 participated in a post-study interview, which employed a semistructured topic guide to assess perceptions and experiences of using plain packs. Trends in the data show that in comparison with branded packaging, plain packaging increased negative perceptions and feelings about the pack and about smoking. Plain packaging also increased avoidant behaviour (hiding the pack, covering the pack), certain smoking cessation behaviours, such as smoking less around others and forgoing cigarettes, and thinking about quitting. Almost half (n=8) of those in the post-study interview, predominantly women (n=6), reported that the use of plain packs had either increased avoidant behaviour or reduced consumption. This pilot naturalistic study suggests that plain packaging could potentially help reduce tobacco consumption among some young adult smokers, and women in particular. Employing an innovative research methodology, the findings of this study are consistent with, and indeed support, past plain packaging research.

Components of the Early Apollo Scientific Experiments Package (EASEP)

NASA Image and Video Library

1969-07-20

AS11-37-5551 (20 July 1969) --- Two components of the Early Apollo Scientific Experiments Package (EASEP) are seen deployed on the lunar surface in this view photographed from inside the Lunar Module (LM). In the far background is the Passive Seismic Experiment Package (PSEP); and to the right and closer to the camera is the Laser Ranging Retro-Reflector (LR-3). The footprints of Apollo 11 astronauts Neil A. Armstrong and Edwin E. Aldrin Jr. are very distinct in the lunar soil.

Scilab software as an alternative low-cost computing in solving the linear equations problem

NASA Astrophysics Data System (ADS)

Agus, Fahrul; Haviluddin

2017-02-01

Numerical computation packages are widely used both in teaching and research. These packages consist of license (proprietary) and open source software (non-proprietary). One of the reasons to use the package is a complexity of mathematics function (i.e., linear problems). Also, number of variables in a linear or non-linear function has been increased. The aim of this paper was to reflect on key aspects related to the method, didactics and creative praxis in the teaching of linear equations in higher education. If implemented, it could be contribute to a better learning in mathematics area (i.e., solving simultaneous linear equations) that essential for future engineers. The focus of this study was to introduce an additional numerical computation package of Scilab as an alternative low-cost computing programming. In this paper, Scilab software was proposed some activities that related to the mathematical models. In this experiment, four numerical methods such as Gaussian Elimination, Gauss-Jordan, Inverse Matrix, and Lower-Upper Decomposition (LU) have been implemented. The results of this study showed that a routine or procedure in numerical methods have been created and explored by using Scilab procedures. Then, the routine of numerical method that could be as a teaching material course has exploited.

Practically prepared? Pre-intern student views following an education package.

PubMed

McKenzie, Susan; Mellis, Craig

2017-01-01

Graduating medical students enter their internship with varied levels of practical experience in procedural skills. To address this problem, many medical schools have introduced intensive skill training courses immediately prior to graduation. This study examines the impact of a pre-intern (PrInt) education package, consisting of a short intensive course, followed by a one-month clinical attachment. In September 2014, all PrInt students (n = 53) at the Central Clinical School (Sydney, NSW, Australia) attended three days of intensive training. This included a didactic introduction, case-based scenarios, and interactive workshops. This was followed by four weeks of targeted, experiential learning during a clinical attachment (PrInt term). Immediately prior to training and following PrInt, all students were invited to complete a six-domain questionnaire containing 40 subscale closed questions to assess their knowledge, experience, and confidence in key practical skills essential for a successful internship. A total of 41/53 (77%) students completed an identical questionnaire prior to PrInt, and 37/53 (70%) immediately following PrInt. Respondents reported statistically significant increases in their experience, ability, knowledge, and confidence in a number of domains. The key changes were the following: knowledge of pharmacy skills (mean improvement = 26.48, confidence interval 95% [CI 95%] = 17.29-35.66, p ≤ 0.0001) and management of procedural skills (mean = 24.46, CI 95% = 16.58-32.34, p ≤ 0.0001). Despite the positive overall increase in most domains, some subscale results remained low following the educational package; only 44% students had inserted a nasogastric tube; only 44% reported confidence in commencing patients on warfarin; and only 42% in managing a hospital emergency. Surprisingly, there was a slight decline both in confidence in communicating with members of the hospital team (10%) and in awareness of the causes of hypoglycemia (7%). Final year students perceived substantial benefit from an educational package specifically aimed at improving their practical skills immediately prior to internship.

Practically prepared? Pre-intern student views following an education package

PubMed Central

McKenzie, Susan; Mellis, Craig

2017-01-01

Background Graduating medical students enter their internship with varied levels of practical experience in procedural skills. To address this problem, many medical schools have introduced intensive skill training courses immediately prior to graduation. This study examines the impact of a pre-intern (PrInt) education package, consisting of a short intensive course, followed by a one-month clinical attachment. Methods In September 2014, all PrInt students (n = 53) at the Central Clinical School (Sydney, NSW, Australia) attended three days of intensive training. This included a didactic introduction, case-based scenarios, and interactive workshops. This was followed by four weeks of targeted, experiential learning during a clinical attachment (PrInt term). Immediately prior to training and following PrInt, all students were invited to complete a six-domain questionnaire containing 40 subscale closed questions to assess their knowledge, experience, and confidence in key practical skills essential for a successful internship. Results A total of 41/53 (77%) students completed an identical questionnaire prior to PrInt, and 37/53 (70%) immediately following PrInt. Respondents reported statistically significant increases in their experience, ability, knowledge, and confidence in a number of domains. The key changes were the following: knowledge of pharmacy skills (mean improvement = 26.48, confidence interval 95% [CI 95%] = 17.29–35.66, p ≤ 0.0001) and management of procedural skills (mean = 24.46, CI 95% = 16.58–32.34, p ≤ 0.0001). Despite the positive overall increase in most domains, some subscale results remained low following the educational package; only 44% students had inserted a nasogastric tube; only 44% reported confidence in commencing patients on warfarin; and only 42% in managing a hospital emergency. Surprisingly, there was a slight decline both in confidence in communicating with members of the hospital team (10%) and in awareness of the causes of hypoglycemia (7%). Conclusion Final year students perceived substantial benefit from an educational package specifically aimed at improving their practical skills immediately prior to internship. PMID:28184172

Guide to using Cuechart, Tellagraf, and Disspla at ANL

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bertoncini, P.J.; Thommes, M.M.

1986-01-01

Guide to Curchart, Tellagraf, and Disspla at ANL provides information necessary for using the three ISSCO graphics packages at Argonne: Cuechart is a cue-and-response program available in CMS that aids users in creating bar charts, line charts, pie charts, and word charts. It is appropriate for users with little or no previous graphics experience. Cuechart provides much of the capability of Tellagraf without the user's having to learn Tellagraf commands. Tellagraf is a more powerful, easy-to-use graphics package also available in CMS. With a little training, scientists, administrators, and secretaries can produce sophisticated publication-quality log or linear plots, bar charts,more » pie charts, tables, or posters. Disspla is a more versatile and sophisticated graphics package. It is available in both CMS and batch and consists of several hundred Fortran-callable and PL/I-callable subroutines that will enable you to obtain professional quality plots. In addition to log or linear plots, bar charts, pie charts, and pages of text, Disspla provides subroutines for contour plots, 3-D plots, and world maps.« less

Practical Issues in Estimating Classification Accuracy and Consistency with R Package cacIRT

ERIC Educational Resources Information Center

Lathrop, Quinn N.

2015-01-01

There are two main lines of research in estimating classification accuracy (CA) and classification consistency (CC) under Item Response Theory (IRT). The R package cacIRT provides computer implementations of both approaches in an accessible and unified framework. Even with available implementations, there remains decisions a researcher faces when…

Early performance of the 12-GHz, 200-watt transmitter experiment package in the communications technology satellite

NASA Technical Reports Server (NTRS)

1977-01-01

Measured performance characteristics of the transmitter experiment package (TEP) aboard the Communications Technology Satellite for the first 90 operating days in orbit are presented. The TEP consists of a nominal 200-watt output stage tube (OST), a supporting power processing system (PPS), and a variable-conductance heat pipe system (VCHPS). The OST, a traveling-wave tube augmented with a 10-stage depressed collector, has an overall saturated average efficiency of 51.5 percent and an average saturated radiofrequency (RF) output power at center-band frequency of 240 watts. The PPS operated with a measured efficiency of 86.5 percent to 88.5 percent. The VCHPS, using three pipes to conduct heat from the PPS and the body of the OST to a 52-centimeter by 124-centimeter (20.5-in. by 48.75-in.) radiator fin, maintained by the PPS baseplate temperature below 50 C for all operating conditions. The TEP performance characteristics presented include frequency response, RF output power, efficiency, and distortions. Communications characteristics were evaluated by using both video and audio modulated signals.

Fast and Accurate Protein False Discovery Rates on Large-Scale Proteomics Data Sets with Percolator 3.0

NASA Astrophysics Data System (ADS)

The, Matthew; MacCoss, Michael J.; Noble, William S.; Käll, Lukas

2016-11-01

Percolator is a widely used software tool that increases yield in shotgun proteomics experiments and assigns reliable statistical confidence measures, such as q values and posterior error probabilities, to peptides and peptide-spectrum matches (PSMs) from such experiments. Percolator's processing speed has been sufficient for typical data sets consisting of hundreds of thousands of PSMs. With our new scalable approach, we can now also analyze millions of PSMs in a matter of minutes on a commodity computer. Furthermore, with the increasing awareness for the need for reliable statistics on the protein level, we compared several easy-to-understand protein inference methods and implemented the best-performing method—grouping proteins by their corresponding sets of theoretical peptides and then considering only the best-scoring peptide for each protein—in the Percolator package. We used Percolator 3.0 to analyze the data from a recent study of the draft human proteome containing 25 million spectra (PM:24870542). The source code and Ubuntu, Windows, MacOS, and Fedora binary packages are available from http://percolator.ms/ under an Apache 2.0 license.

Fast and Accurate Protein False Discovery Rates on Large-Scale Proteomics Data Sets with Percolator 3.0.

PubMed

The, Matthew; MacCoss, Michael J; Noble, William S; Käll, Lukas

2016-11-01

Percolator is a widely used software tool that increases yield in shotgun proteomics experiments and assigns reliable statistical confidence measures, such as q values and posterior error probabilities, to peptides and peptide-spectrum matches (PSMs) from such experiments. Percolator's processing speed has been sufficient for typical data sets consisting of hundreds of thousands of PSMs. With our new scalable approach, we can now also analyze millions of PSMs in a matter of minutes on a commodity computer. Furthermore, with the increasing awareness for the need for reliable statistics on the protein level, we compared several easy-to-understand protein inference methods and implemented the best-performing method-grouping proteins by their corresponding sets of theoretical peptides and then considering only the best-scoring peptide for each protein-in the Percolator package. We used Percolator 3.0 to analyze the data from a recent study of the draft human proteome containing 25 million spectra (PM:24870542). The source code and Ubuntu, Windows, MacOS, and Fedora binary packages are available from http://percolator.ms/ under an Apache 2.0 license. Graphical Abstract ᅟ.

Evaluation of copy number variation detection for a SNP array platform

PubMed Central

2014-01-01

Background Copy Number Variations (CNVs) are usually inferred from Single Nucleotide Polymorphism (SNP) arrays by use of some software packages based on given algorithms. However, there is no clear understanding of the performance of these software packages; it is therefore difficult to select one or several software packages for CNV detection based on the SNP array platform. We selected four publicly available software packages designed for CNV calling from an Affymetrix SNP array, including Birdsuite, dChip, Genotyping Console (GTC) and PennCNV. The publicly available dataset generated by Array-based Comparative Genomic Hybridization (CGH), with a resolution of 24 million probes per sample, was considered to be the “gold standard”. Compared with the CGH-based dataset, the success rate, average stability rate, sensitivity, consistence and reproducibility of these four software packages were assessed compared with the “gold standard”. Specially, we also compared the efficiency of detecting CNVs simultaneously by two, three and all of the software packages with that by a single software package. Results Simply from the quantity of the detected CNVs, Birdsuite detected the most while GTC detected the least. We found that Birdsuite and dChip had obvious detecting bias. And GTC seemed to be inferior because of the least amount of CNVs it detected. Thereafter we investigated the detection consistency produced by one certain software package and the rest three software suits. We found that the consistency of dChip was the lowest while GTC was the highest. Compared with the CNVs detecting result of CGH, in the matching group, GTC called the most matching CNVs, PennCNV-Affy ranked second. In the non-overlapping group, GTC called the least CNVs. With regards to the reproducibility of CNV calling, larger CNVs were usually replicated better. PennCNV-Affy shows the best consistency while Birdsuite shows the poorest. Conclusion We found that PennCNV outperformed the other three packages in the sensitivity and specificity of CNV calling. Obviously, each calling method had its own limitations and advantages for different data analysis. Therefore, the optimized calling methods might be identified using multiple algorithms to evaluate the concordance and discordance of SNP array-based CNV calling. PMID:24555668

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bornea, A.; Zamfirache, M.; Stefan, L.

ICIT (Institute for Cryogenics and Isotopic Technologies) has used its experience in cryogenic water distillation process to propose a similar process for hydrogen distillation that can be used in detritiation technologies. This process relies on the same packages but a stainless filling is tested instead of the phosphorous bronze filling used for water distillation. This paper presents two types of packages developed for hydrogen distillation, both have a stainless filling but it differs in terms of density, exchange surface and specific volume. Performance data have been obtained on laboratory scale. In order to determine the characteristics of the package, themore » installation was operated in the total reflux mode, for different flow rate for the liquid. There were made several experiments considering different operating conditions. Samples extracted at the top and bottom of cryogenic distillation column allowed mathematical processing to determine the separation performance. The experiments show a better efficiency for the package whose exchange surface was higher and there were no relevant differences between both packages as the operating pressure of the cryogenic column was increasing. For a complete characterization of the packages, future experiments will be considered to determine performance at various velocities in the column and their correlation with the pressure in the column. We plan further experiments to separate tritium from the mixture of isotopes DT, having in view that our goal is to apply this results to a detritiation plant.« less

Hybrid Soft Soil Tire Model (HSSTM). Part 1: Tire Material and Structure Modeling

DTIC Science & Technology

2015-04-28

commercially available vehicle simulation packages. Model parameters are obtained using a validated finite element tire model, modal analysis, and other...design of experiment matrix. This data, in addition to modal analysis data were used to validate the tire model. Furthermore, to study the validity...é ë ê ê ê ê ê ê ê ù û ú ú ú ú ú ú ú (78) The applied forces to the rim center consist of the axle forces and suspension forces: FFF Gsuspension G

MeV+R: using MeV as a graphical user interface for Bioconductor applications in microarray analysis

PubMed Central

Chu, Vu T; Gottardo, Raphael; Raftery, Adrian E; Bumgarner, Roger E; Yeung, Ka Yee

2008-01-01

We present MeV+R, an integration of the JAVA MultiExperiment Viewer program with Bioconductor packages. This integration of MultiExperiment Viewer and R is easily extensible to other R packages and provides users with point and click access to traditionally command line driven tools written in R. We demonstrate the ability to use MultiExperiment Viewer as a graphical user interface for Bioconductor applications in microarray data analysis by incorporating three Bioconductor packages, RAMA, BRIDGE and iterativeBMA. PMID:18652698

Methods and codes for neutronic calculations of the MARIA research reactor.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Andrzejewski, K.; Kulikowska, T.; Bretscher, M. M.

2002-02-18

The core of the MARIA high flux multipurpose research reactor is highly heterogeneous. It consists of beryllium blocks arranged in 6 x 8 matrix, tubular fuel assemblies, control rods and irradiation channels. The reflector is also heterogeneous and consists of graphite blocks clad with aluminum. Its structure is perturbed by the experimental beam tubes. This paper presents methods and codes used to calculate the MARIA reactor neutronics characteristics and experience gained thus far at IAE and ANL. At ANL the methods of MARIA calculations were developed in connection with the RERTR program. At IAE the package of programs was developedmore » to help its operator in optimization of fuel utilization.« less

"FluSpec": A Simulated Experiment in Fluorescence Spectroscopy

ERIC Educational Resources Information Center

Bigger, Stephen W.; Bigger, Andrew S.; Ghiggino, Kenneth P.

2014-01-01

The "FluSpec" educational software package is a fully contained tutorial on the technique of fluorescence spectroscopy as well as a simulator on which experiments can be performed. The procedure for each of the experiments is also contained within the package along with example analyses of results that are obtained using the software.

Diagnostic Testing Package DX v 2.0 Technical Specification. Methodology Project.

ERIC Educational Resources Information Center

McArthur, David

This paper contains the technical specifications, schematic diagrams, and program printout for a computer software package for the development and administration of diagnostic tests. The second version of the Diagnostic Testing Package DX consists of a PASCAL-based set of modules located in two main programs: (1) EDITTEST creates, modifies, and…

Comparison of Computer Based Instruction to Behavior Skills Training for Teaching Staff Implementation of Discrete-Trial Instruction with an Adult with Autism

ERIC Educational Resources Information Center

Nosik, Melissa R.; Williams, W. Larry; Garrido, Natalia; Lee, Sarah

2013-01-01

In the current study, behavior skills training (BST) is compared to a computer based training package for teaching discrete trial instruction to staff, teaching an adult with autism. The computer based training package consisted of instructions, video modeling and feedback. BST consisted of instructions, modeling, rehearsal and feedback. Following…

Is consumer response to plain/standardised tobacco packaging consistent with framework convention on tobacco control guidelines? A systematic review of quantitative studies.

PubMed

Stead, Martine; Moodie, Crawford; Angus, Kathryn; Bauld, Linda; McNeill, Ann; Thomas, James; Hastings, Gerard; Hinds, Kate; O'Mara-Eves, Alison; Kwan, Irene; Purves, Richard I; Bryce, Stuart L

2013-01-01

Standardised or 'plain' tobacco packaging was introduced in Australia in December 2012 and is currently being considered in other countries. The primary objective of this systematic review was to locate, assess and synthesise published and grey literature relating to the potential impacts of standardised tobacco packaging as proposed by the guidelines for the international Framework Convention on Tobacco Control: reduced appeal, increased salience and effectiveness of health warnings, and more accurate perceptions of product strength and harm. Electronic databases were searched and researchers in the field were contacted to identify studies. Eligible studies were published or unpublished primary research of any design, issued since 1980 and concerning tobacco packaging. Twenty-five quantitative studies reported relevant outcomes and met the inclusion criteria. A narrative synthesis was conducted. Studies that explored the impact of package design on appeal consistently found that standardised packaging reduced the appeal of cigarettes and smoking, and was associated with perceived lower quality, poorer taste and less desirable smoker identities. Although findings were mixed, standardised packs tended to increase the salience and effectiveness of health warnings in terms of recall, attention, believability and seriousness, with effects being mediated by the warning size, type and position on pack. Pack colour was found to influence perceptions of product harm and strength, with darker coloured standardised packs generally perceived as containing stronger tasting and more harmful cigarettes than fully branded packs; lighter coloured standardised packs suggested weaker and less harmful cigarettes. Findings were largely consistent, irrespective of location and sample. The evidence strongly suggests that standardised packaging will reduce the appeal of packaging and of smoking in general; that it will go some way to reduce consumer misperceptions regarding product harm based upon package design; and will help make the legally required on-pack health warnings more salient.

Is Consumer Response to Plain/Standardised Tobacco Packaging Consistent with Framework Convention on Tobacco Control Guidelines? A Systematic Review of Quantitative Studies

PubMed Central

Stead, Martine; Moodie, Crawford; Angus, Kathryn; Bauld, Linda; McNeill, Ann; Thomas, James; Hastings, Gerard; Hinds, Kate; O'Mara-Eves, Alison; Kwan, Irene; Purves, Richard I.; Bryce, Stuart L.

2013-01-01

Background and Objectives Standardised or ‘plain’ tobacco packaging was introduced in Australia in December 2012 and is currently being considered in other countries. The primary objective of this systematic review was to locate, assess and synthesise published and grey literature relating to the potential impacts of standardised tobacco packaging as proposed by the guidelines for the international Framework Convention on Tobacco Control: reduced appeal, increased salience and effectiveness of health warnings, and more accurate perceptions of product strength and harm. Methods Electronic databases were searched and researchers in the field were contacted to identify studies. Eligible studies were published or unpublished primary research of any design, issued since 1980 and concerning tobacco packaging. Twenty-five quantitative studies reported relevant outcomes and met the inclusion criteria. A narrative synthesis was conducted. Results Studies that explored the impact of package design on appeal consistently found that standardised packaging reduced the appeal of cigarettes and smoking, and was associated with perceived lower quality, poorer taste and less desirable smoker identities. Although findings were mixed, standardised packs tended to increase the salience and effectiveness of health warnings in terms of recall, attention, believability and seriousness, with effects being mediated by the warning size, type and position on pack. Pack colour was found to influence perceptions of product harm and strength, with darker coloured standardised packs generally perceived as containing stronger tasting and more harmful cigarettes than fully branded packs; lighter coloured standardised packs suggested weaker and less harmful cigarettes. Findings were largely consistent, irrespective of location and sample. Conclusions The evidence strongly suggests that standardised packaging will reduce the appeal of packaging and of smoking in general; that it will go some way to reduce consumer misperceptions regarding product harm based upon package design; and will help make the legally required on-pack health warnings more salient. PMID:24146791

GASCan 2 payload integration

NASA Technical Reports Server (NTRS)

Cody, Dennis J.; Concepcion, Allan G.; Watras, Edward C., III

1995-01-01

This project, conducted in cooperation with the NASA Advanced Space Design Program, is part of an ongoing effort to place an experiment package into space. The goal of this project is to build and test flight-ready hardware that can be launched from the Space Shuttle. Get Away Special Canister 2 (GASCan 2) consists of three separate experiments. The Ionospheric Properties and Propagation Experiment (IPPE) determines effects of the ionosphere on radio wave propagation. The Microgravity Ignition experiment (MGI) tests the effects of combustion in a microgravity environment. The Rotational Fluid Flow experiment (RFF) examines fluid behavior under varying levels of gravity. This year the following tasks were completed: design of the IPPE antenna, X- and J-cell battery boxes, J-cell battery box enclosure, and structural bumpers; construction of the MGI canisters, MGI mounting brackets, IPPE antenna, and battery boxes; and the selection of the RFF's operating fluid and the analysis of the fluid behavior under microgravity test conditions.

GT-SUPREEM: the Georgia Tech summer undergraduate packaging research and engineering experience for minorities

NASA Astrophysics Data System (ADS)

May, Gary S.

1996-07-01

The Georgia Tech SUmmer Undergraduate Packaging Research and Engineering Experience for Minorities (GT-SUPREEM) is an eight-week summer program designed to attract qualified minority students to pursue graduate degrees in packaging- related disciplines. The program is conducted under the auspices of the Georgia Tech Engineering Research Center in Low-Cost Electronic Packaging, which is sponsored by the National Science Foundation. In this program, nine junior and senior level undergraduate students are selected on a nationwide basis and paired with a faculty advisor to undertake research projects in the Packaging Research CEnter. The students are housed on campus and provided with a $DLR3,000 stipend and a travel allowance. At the conclusion of the program, the students present both oral and written project summaries. It is anticipated that this experience will motivate these students to become applicants for graduate study in ensuring years. This paper will provide an overview of the GT-SUPREEM program, including student research activities, success stories, lessons learned, and overall program outlook.

CompGO: an R package for comparing and visualizing Gene Ontology enrichment differences between DNA binding experiments.

PubMed

Waardenberg, Ashley J; Basset, Samuel D; Bouveret, Romaric; Harvey, Richard P

2015-09-02

Gene ontology (GO) enrichment is commonly used for inferring biological meaning from systems biology experiments. However, determining differential GO and pathway enrichment between DNA-binding experiments or using the GO structure to classify experiments has received little attention. Herein, we present a bioinformatics tool, CompGO, for identifying Differentially Enriched Gene Ontologies, called DiEGOs, and pathways, through the use of a z-score derivation of log odds ratios, and visualizing these differences at GO and pathway level. Through public experimental data focused on the cardiac transcription factor NKX2-5, we illustrate the problems associated with comparing GO enrichments between experiments using a simple overlap approach. We have developed an R/Bioconductor package, CompGO, which implements a new statistic normally used in epidemiological studies for performing comparative GO analyses and visualizing comparisons from . BED data containing genomic coordinates as well as gene lists as inputs. We justify the statistic through inclusion of experimental data and compare to the commonly used overlap method. CompGO is freely available as a R/Bioconductor package enabling easy integration into existing pipelines and is available at: http://www.bioconductor.org/packages/release/bioc/html/CompGO.html packages/release/bioc/html/CompGO.html.

Portable computing - A fielded interactive scientific application in a small off-the-shelf package

NASA Technical Reports Server (NTRS)

Groleau, Nicolas; Hazelton, Lyman; Frainier, Rich; Compton, Michael; Colombano, Silvano; Szolovits, Peter

1993-01-01

Experience with the design and implementation of a portable computing system for STS crew-conducted science is discussed. Principal-Investigator-in-a-Box (PI) will help the SLS-2 astronauts perform vestibular (human orientation system) experiments in flight. PI is an interactive system that provides data acquisition and analysis, experiment step rescheduling, and various other forms of reasoning to astronaut users. The hardware architecture of PI consists of a computer and an analog interface box. 'Off-the-shelf' equipment is employed in the system wherever possible in an effort to use widely available tools and then to add custom functionality and application codes to them. Other projects which can help prospective teams to learn more about portable computing in space are also discussed.

Space shuttle/food system study. Package feasibility study, modifications 3S, 4C and 5S

NASA Technical Reports Server (NTRS)

1974-01-01

An optimum feeding system for the space shuttle was presented. This system consisted of all rehydratable type foods which were enclosed in a 4 in. x 4 in. x 1 in. flexible package. A feasibility follow-on study was conducted, and two acceptable, feasible prototypes for this package are described.

The effect of a simulation training package on skill acquisition for duplex arterial stenosis detection.

PubMed

Jaffer, Usman; Normahani, Pasha; Singh, Prashant; Aslam, Mohammed; Standfield, Nigel J

2015-01-01

In vascular surgery, duplex ultrasonography is a valuable diagnostic tool in patients with peripheral vascular disease, and there is increasing demand for vascular surgeons to be able to perform duplex scanning. This study evaluates the role of a novel simulation training package on vascular ultrasound (US) skill acquisition. A total of 19 novices measured predefined stenosis in a simulated pulsatile vessel using both peak systolic velocity ratio (PSVR) and diameter reduction (DR) methods before and after a short period of training using a simulated training package. The training package consisted of a simulated pulsatile vessel phantom, a set of instructional videos, duplex ultrasound objective structured assessment of technical skills (DUOSATS) tool, and a portable US scanner. Quantitative metrics (procedure time, percentage error using PSVR and DR methods, DUOSAT scores, and global rating scores) before and after training were compared. Subjects spent a median time of 144 mins (IQR: 60-195) training using the simulation package. Subjects exhibited statistically significant improvements when comparing pretraining and posttraining DUOSAT scores (pretraining = 17 [16-19.3] vs posttraining = 30 [27.8-31.8]; p < 0.01), global rating score (pretraining = 1 [1-2] vs posttraining = 4 [3.8-4]; p < 0.01), percentage error using both the DR (pretraining = 12.6% [9-29.6] vs posttraining = 10.3% [8.9-11.1]; p = 0.03) and PSVR (pretraining = 60% [40-60] vs posttraining = 20% [6.7-20]; p < 0.01) methods. In this study, subjects with no previous practical US experience developed the ability to both acquire and interpret arterial duplex images in a pulsatile simulated phantom following a short period of goal direct training using a simulation training package. A simulation training package may be a valuable tool for integration into a vascular training program. However, further work is needed to explore whether these newly attained skills are translated into clinical assessment. Crown Copyright © 2014. Published by Elsevier Inc. All rights reserved.

Packaging signals in two single-stranded RNA viruses imply a conserved assembly mechanism and geometry of the packaged genome.

PubMed

Dykeman, Eric C; Stockley, Peter G; Twarock, Reidun

2013-09-09

The current paradigm for assembly of single-stranded RNA viruses is based on a mechanism involving non-sequence-specific packaging of genomic RNA driven by electrostatic interactions. Recent experiments, however, provide compelling evidence for sequence specificity in this process both in vitro and in vivo. The existence of multiple RNA packaging signals (PSs) within viral genomes has been proposed, which facilitates assembly by binding coat proteins in such a way that they promote the protein-protein contacts needed to build the capsid. The binding energy from these interactions enables the confinement or compaction of the genomic RNAs. Identifying the nature of such PSs is crucial for a full understanding of assembly, which is an as yet untapped potential drug target for this important class of pathogens. Here, for two related bacterial viruses, we determine the sequences and locations of their PSs using Hamiltonian paths, a concept from graph theory, in combination with bioinformatics and structural studies. Their PSs have a common secondary structure motif but distinct consensus sequences and positions within the respective genomes. Despite these differences, the distributions of PSs in both viruses imply defined conformations for the packaged RNA genomes in contact with the protein shell in the capsid, consistent with a recent asymmetric structure determination of the MS2 virion. The PS distributions identified moreover imply a preferred, evolutionarily conserved assembly pathway with respect to the RNA sequence with potentially profound implications for other single-stranded RNA viruses known to have RNA PSs, including many animal and human pathogens. Copyright © 2013 Elsevier Ltd. All rights reserved.

Packaging of electro-microfluidic devices

DOEpatents

Benavides, Gilbert L.; Galambos, Paul C.; Emerson, John A.; Peterson, Kenneth A.; Giunta, Rachel K.; Zamora, David Lee; Watson, Robert D.

2003-04-15

A new architecture for packaging surface micromachined electro-microfluidic devices is presented. This architecture relies on two scales of packaging to bring fluid to the device scale (picoliters) from the macro-scale (microliters). The architecture emulates and utilizes electronics packaging technology. The larger package consists of a circuit board with embedded fluidic channels and standard fluidic connectors (e.g. Fluidic Printed Wiring Board). The embedded channels connect to the smaller package, an Electro-Microfluidic Dual-Inline-Package (EMDIP) that takes fluid to the microfluidic integrated circuit (MIC). The fluidic connection is made to the back of the MIC through Bosch-etched holes that take fluid to surface micromachined channels on the front of the MIC. Electrical connection is made to bond pads on the front of the MIC.

Packaging of electro-microfluidic devices

DOEpatents

Benavides, Gilbert L.; Galambos, Paul C.; Emerson, John A.; Peterson, Kenneth A.; Giunta, Rachel K.; Watson, Robert D.

2002-01-01

A new architecture for packaging surface micromachined electro-microfluidic devices is presented. This architecture relies on two scales of packaging to bring fluid to the device scale (picoliters) from the macro-scale (microliters). The architecture emulates and utilizes electronics packaging technology. The larger package consists of a circuit board with embedded fluidic channels and standard fluidic connectors (e.g. Fluidic Printed Wiring Board). The embedded channels connect to the smaller package, an Electro-Microfluidic Dual-Inline-Package (EMDIP) that takes fluid to the microfluidic integrated circuit (MIC). The fluidic connection is made to the back of the MIC through Bosch-etched holes that take fluid to surface micromachined channels on the front of the MIC. Electrical connection is made to bond pads on the front of the MIC.

An electron-beam dose deposition experiment: TIGER 1-D simulation code versus thermoluminescent dosimetry

NASA Astrophysics Data System (ADS)

Murrill, Steven R.; Tipton, Charles W.; Self, Charles T.

1991-03-01

The dose absorbed in an integrated circuit (IC) die exposed to a pulse of low-energy electrons is a strong function of both electron energy and surrounding packaging materials. This report describes an experiment designed to measure how well the Integrated TIGER Series one-dimensional (1-D) electron transport simulation program predicts dose correction factors for a state-of-the-art IC package and package/printed circuit board (PCB) combination. These derived factors are compared with data obtained experimentally using thermoluminescent dosimeters (TLD's) and the FX-45 flash x-ray machine (operated in electron-beam (e-beam) mode). The results of this experiment show that the TIGER 1-D simulation code can be used to accurately predict FX-45 e-beam dose deposition correction factors for reasonably complex IC packaging configurations.

48 CFR 552.211-85 - Consistent pack and package requirements.

Code of Federal Regulations, 2010 CFR

2010-10-01

.... If volume warrants, the Government may also order in truckload or carload quantities provided such... change the package quantities. Requests for changes shall be directed to the Contracting Officer or...

Vibration analysis of printed circuit boards: Effect of boundary condition

NASA Astrophysics Data System (ADS)

Prashanth, M. D.

2018-04-01

A spacecraft consists of a number of electronic packages to meet the functional requirements. An electronic package is generally an assembly of printed circuit boards placed in a mechanical housing. A number of electronic components are mounted on the printed circuit board (PCB). A spacecraft experiences various types of loads during its launch such as vibration, acoustic and shock loads. Prediction of response for printed circuit boards due to vibration loads is important for mechanical design and reliability of electronic packages. The modeling and analysis of printed circuit boards is required for accurate prediction of response due to vibration loads. The response of PCB is highly dependent on the mounting configuration of PCB. In addition, anti-vibration mounts or stiffeners are used to reduce the PCB response. Vibration analysis of printed circuit boards is carried out using finite element method. The objective of this paper is to determine the dynamic characteristics of a printed circuit board. Modeling and analysis of PCB shall be carried out to study the effect of boundary conditions on the vibration response. The modeling of stiffeners or ribs shall also be considered in detail. The analysis results shall be validated using vibration tests of PCB.

Variations in algorithm implementation among quantitative texture analysis software packages

NASA Astrophysics Data System (ADS)

Foy, Joseph J.; Mitta, Prerana; Nowosatka, Lauren R.; Mendel, Kayla R.; Li, Hui; Giger, Maryellen L.; Al-Hallaq, Hania; Armato, Samuel G.

2018-02-01

Open-source texture analysis software allows for the advancement of radiomics research. Variations in texture features, however, result from discrepancies in algorithm implementation. Anatomically matched regions of interest (ROIs) that captured normal breast parenchyma were placed in the magnetic resonance images (MRI) of 20 patients at two time points. Six first-order features and six gray-level co-occurrence matrix (GLCM) features were calculated for each ROI using four texture analysis packages. Features were extracted using package-specific default GLCM parameters and using GLCM parameters modified to yield the greatest consistency among packages. Relative change in the value of each feature between time points was calculated for each ROI. Distributions of relative feature value differences were compared across packages. Absolute agreement among feature values was quantified by the intra-class correlation coefficient. Among first-order features, significant differences were found for max, range, and mean, and only kurtosis showed poor agreement. All six second-order features showed significant differences using package-specific default GLCM parameters, and five second-order features showed poor agreement; with modified GLCM parameters, no significant differences among second-order features were found, and all second-order features showed poor agreement. While relative texture change discrepancies existed across packages, these differences were not significant when consistent parameters were used.

75 FR 34156 - United States

Federal Register 2010, 2011, 2012, 2013, 2014

2010-06-16

... the package's failure. A failure of the package could expose the medical device to microbes, bacteria... research and development efforts, including, but not limited to, designs and experiments and the results of successful and unsuccessful designs and experiments; and (b) With respect to any intangible assets that are...

30-kW class Arcjet Advanced Technology Transition Demonstration (ATTD) flight experiment diagnostic package

NASA Astrophysics Data System (ADS)

Kriebel, M. M.; Stevens, N. J.

1992-07-01

TRW, Rocket Research Co and Defense Systems Inc are developing a space qualified 30-kW class arcjet flight unit as a part of the Arcjet ATTD program. During space operation the package will measure plume deposition and contamination, electromagnetic interference, thermal radiation, arcjet thruster performance, and plume heating in order to quantify arcjet operational interactions. The Electric Propulsion Space Experiment (ESEX) diagnostic package is described. The goals of ESEX are the demonstration of a high powered arcjet performance and the measurement of potential arcjet-spacecraft interactions which cannot be determined in ground facilities. Arcjet performance, plume characterization, thermal radiation flux and the electromagnetic interference (EMI) experiment as well as experiment operations with a preliminary operations plan are presented.

IIP Update: A Packaged Coherent Doppler Wind Lidar Transceiver. Doppler Aerosol WiNd Lidar (DAWN)

NASA Technical Reports Server (NTRS)

Kavaya, Michael J.; Koch, Grady J.; Yu, Jirong; Trieu, Bo C.; Amzajerdian, Farzin; Singh, Upendra N.; Petros, Mulugeta

2006-01-01

The state-of-the-art 2-micron coherent Doppler wind lidar breadboard at NASA/LaRC will be engineered and compactly packaged consistent with future aircraft flights. The packaged transceiver will be integrated into a coherent Doppler wind lidar system test bed at LaRC. Atmospheric wind measurements will be made to validate the packaged technology. This will greatly advance the coherent part of the hybrid Doppler wind lidar solution to the need for global tropospheric wind measurements.

Advanced Manufacturing Systems in Food Processing and Packaging Industry

NASA Astrophysics Data System (ADS)

Shafie Sani, Mohd; Aziz, Faieza Abdul

2013-06-01

In this paper, several advanced manufacturing systems in food processing and packaging industry are reviewed, including: biodegradable smart packaging and Nano composites, advanced automation control system consists of fieldbus technology, distributed control system and food safety inspection features. The main purpose of current technology in food processing and packaging industry is discussed due to major concern on efficiency of the plant process, productivity, quality, as well as safety. These application were chosen because they are robust, flexible, reconfigurable, preserve the quality of the food, and efficient.

STS-39 AFP-675 CIRRIS-1A in OV-103's payload bay (PLB)

NASA Image and Video Library

1991-05-06

STS039-85-073 (28 April- 6 May 1991) --- This 70mm frame, taken from inside the crew cabin, shows a close-up view of the Air Force Program (AFP) 675 package. AFP-675 consists of the Cryogenic Infrared Radiance Instrumentation for Shuttle (CIRRIS)-1A; Far Ultraviolet Camera (FAR-UV) Experiment; Horizon Ultraviolet Program (HUP); Quadruple Ion Neutral Mass Spectrometer (QINMS); and the Uniformly Redundant Array (URA). Much of that hardware is backdropped here against the aft cargo bay bulkhead of Discovery.

EQS Goes R: Simulations for SEM Using the Package REQS

ERIC Educational Resources Information Center

Mair, Patrick; Wu, Eric; Bentler, Peter M.

2010-01-01

The REQS package is an interface between the R environment of statistical computing and the EQS software for structural equation modeling. The package consists of 3 main functions that read EQS script files and import the results into R, call EQS script files from R, and run EQS script files from R and import the results after EQS computations.…

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ferrell, P.C.

This SARP describes the RTG Transportation System Package, a Type B(U) packaging system that is used to transport an RTG or similar payload. The payload, which is included in this SARP, is a generic, enveloping payload that specifically encompasses the General Purpose Heat Source (GPHS) RTG payload. The package consists of two independent containment systems mounted on a shock isolation transport skid and transported within an exclusive-use trailer.

A Recruitment Package for Postsecondary Vocational Education. Final From August 1, 1983 to August 31, 1984. Final Report.

ERIC Educational Resources Information Center

Waltz, Freddie C.; And Others

This recruitment package consists of materials designed to assist those individuals who are responsible for recruiting students into postsecondary vocational education programs. The package, which may be used either as a guide to establishing and implementing a new promotional policy or as a resource to use when planning a specific promotional…

Overview of Germany: The Federal Republic and the Federal States. Social Studies, Grades 6-8. Update 2002.

ERIC Educational Resources Information Center

Blankenship, Glen; Tinkler, D. William

This instructional package, consisting of a text and 15 transparencies, is designed for middle school classrooms. The four lessons in the package correlate to the study of world cultures (perspective taking and symbols), geography, and government. The materials in the package focus on national studies and state studies from a comparative United…

Food for a Healthy Mom and Baby. Nutrition. How to Have a Healthy Pregnancy.

ERIC Educational Resources Information Center

Randall, Jill; And Others

This package consists of two sets of bilingual instructional materials for use in helping Indochinese refugees learn prenatal care and nutrition skills. Included in the package are Vietnamese, Laotian, and English translations of an instructional booklet dealing with how to have a healthy pregnancy. The second item in the package is a set of…

Skills Analysis. Workshop Package on Skills Analysis, Skills Audit and Training Needs Analysis.

ERIC Educational Resources Information Center

Hayton, Geoff; And Others

This four-part package is designed to assist Australian workshop leaders running 2-day workshops on skills analysis, skills audit, and training needs analysis. Part A contains information on how to use the package and a list of workshop aims. Parts B, C, and D consist, respectively, of the workshop leader's guide; overhead transparency sheets and…

Unlocking the potential of publicly available microarray data using inSilicoDb and inSilicoMerging R/Bioconductor packages.

PubMed

Taminau, Jonatan; Meganck, Stijn; Lazar, Cosmin; Steenhoff, David; Coletta, Alain; Molter, Colin; Duque, Robin; de Schaetzen, Virginie; Weiss Solís, David Y; Bersini, Hugues; Nowé, Ann

2012-12-24

With an abundant amount of microarray gene expression data sets available through public repositories, new possibilities lie in combining multiple existing data sets. In this new context, analysis itself is no longer the problem, but retrieving and consistently integrating all this data before delivering it to the wide variety of existing analysis tools becomes the new bottleneck. We present the newly released inSilicoMerging R/Bioconductor package which, together with the earlier released inSilicoDb R/Bioconductor package, allows consistent retrieval, integration and analysis of publicly available microarray gene expression data sets. Inside the inSilicoMerging package a set of five visual and six quantitative validation measures are available as well. By providing (i) access to uniformly curated and preprocessed data, (ii) a collection of techniques to remove the batch effects between data sets from different sources, and (iii) several validation tools enabling the inspection of the integration process, these packages enable researchers to fully explore the potential of combining gene expression data for downstream analysis. The power of using both packages is demonstrated by programmatically retrieving and integrating gene expression studies from the InSilico DB repository [https://insilicodb.org/app/].

An experimental analysis of the effectiveness and sustainability of a Chinese tutoring package.

PubMed

Wu, Hang; Miller, L Keith

2012-01-01

This experiment evaluated the effects of training tutors to use an instructional package to teach pronunciation and translation of the Chinese language. Tutors' correct use of the package increased from 68% of trials to 92% after training, and student correct pronunciation increased from 45% to 90%, with similar effects for translation. Continued use of the package, high social validity, and extended follow-up suggest that use of the package may be sustainable.

AN EXPERIMENTAL ANALYSIS OF THE EFFECTIVENESS AND SUSTAINABILITY OF A CHINESE TUTORING PACKAGE

PubMed Central

Wu, Hang; Miller, L. Keith

2012-01-01

This experiment evaluated the effects of training tutors to use an instructional package to teach pronunciation and translation of the Chinese language. Tutors' correct use of the package increased from 68% of trials to 92% after training, and student correct pronunciation increased from 45% to 90%, with similar effects for translation. Continued use of the package, high social validity, and extended follow-up suggest that use of the package may be sustainable. PMID:22403470

Method Of Packaging And Assembling Electro-Microfluidic Devices

DOEpatents

Benavides, Gilbert L.; Galambos, Paul C.; Emerson, John A.; Peterson, Kenneth A.; Giunta, Rachel K.; Zamora, David Lee; Watson, Robert D.

2004-11-23

A new architecture for packaging surface micromachined electro-microfluidic devices is presented. This architecture relies on two scales of packaging to bring fluid to the device scale (picoliters) from the macro-scale (microliters). The architecture emulates and utilizes electronics packaging technology. The larger package consists of a circuit board with embedded fluidic channels and standard fluidic connectors (e.g. Fluidic Printed Wiring Board). The embedded channels connect to the smaller package, an Electro-Microfluidic Dual-Inline-Package (EMDIP) that takes fluid to the microfluidic integrated circuit (MIC). The fluidic connection is made to the back of the MIC through Bosch-etched holes that take fluid to surface micromachined channels on the front of the MIC. Electrical connection is made to bond pads on the front of the MIC.

Volvo drivers' experiences with advanced crash avoidance and related technologies.

PubMed

Eichelberger, Angela H; McCartt, Anne T

2014-01-01

Crash avoidance technologies can potentially prevent or mitigate many crashes, but their success depends in part on driver acceptance. Owners of 2010-2012 model Volvo vehicles with several technologies were interviewed about their experiences. Interviews were conducted in summer 2012 with 155 owners of vehicles with City Safety as a standard feature; 145 owners with an optional technology package that included adaptive cruise control, distance alert, collision warning with full auto brake (and pedestrian detection on certain models), driver alert control, and lane departure warning; and 172 owners with both City Safety and the technology package. The survey response rates were 21 percent for owners with City Safety, 30 percent for owners with the technology package, and 27 percent for owners with both. Ten percent of owners opted out before the telephone survey began, and 18 percent declined to participate when called. Despite some annoyance, most respondents always leave the systems on, although fewer do so for lane departure warning (59%). For each of the systems, at least 80 percent of respondents with the system would want it on their next vehicle. Many respondents reported safer driving habits with the systems (e.g., following less closely with adaptive cruise control, using turn signals more often with lane departure warning). Fewer respondents reported potentially unsafe behavior, such as allowing the vehicle to brake for them at least some of the time. About one third of respondents experienced autonomous braking when they believed they were at risk of crashing, and about one fifth of respondents thought it had prevented a crash. About one fifth of respondents with the technology package reported that they were confused or misunderstood which safety system had activated in their vehicle. Consistent with the results for early adopters in the previous survey of Volvo and Infiniti owners, the present survey found that driver acceptance of the technologies remains high, although less so for lane departure warning. This study is the first to report drivers' experiences with City Safety, a collision avoidance system provided as standard equipment on certain Volvo 2010-2012 models, and driver acceptance of this system was high, although not to the same extent as the optional forward collision avoidance system. Future research should continue to monitor drivers' experiences with these technologies as they become available in more vehicles.

The Vinyl Acetate Content of Packaging Film: A Quantitative Infrared Experiment.

ERIC Educational Resources Information Center

Allpress, K. N.; And Others

1981-01-01

Presents an experiment used in laboratory technician training courses to illustrate the quantitative use of infrared spectroscopy which is based on industrial and laboratory procedures for the determination of vinyl acetate levels in ethylene vinyl acetate packaging films. Includes three approaches to allow for varying path lengths (film…

NASA-DoD Lead-Free Electronics Project

NASA Technical Reports Server (NTRS)

Kessel, Kurt

2009-01-01

In response to concerns about risks from lead-free induced faults to high reliability products, NASA has initiated a multi-year project to provide manufacturers and users with data to clarify the risks of lead-free materials in their products. The project will also be of interest to component manufacturers supplying to high reliability markets. The project was launched in November 2006. The primary technical objective of the project is to undertake comprehensive testing to generate information on failure modes/criteria to better understand the reliability of: (1) Packages (e.g., Thin Small Outline Package [TSOP], Ball Grid Array [BGA], Plastic Dual In-line Package [PDIP]) assembled and reworked with solder interconnects consisting of lead-free alloys (2) Packages (e.g., TSOP, BGA, PDIP) assembled and reworked with solder interconnects consisting of mixed alloys, lead component finish/lead-free solder and lead-free component finish/SnPb solder

Linguistic complexity and information structure in Korean: Evidence from eye-tracking during reading

PubMed Central

Lee, Yoonhyoung; Lee, Hanjung; Gordon, Peter C.

2006-01-01

The nature of the memory processes that support language comprehension and the manner in which information packaging influences online sentence processing were investigated in three experiments that used eye-tracking during reading to measure the ease of understanding complex sentences in Korean. All three experiments examined reading of embedded complement sentences; the third experiment additionally examined reading of sentences with object-modifying, object-extracted relative clauses. In Korean, both of these structures place two NPs with nominative case marking early in the sentence, with the embedded and matrix verbs following later. The type (pronoun, name or description) of these two critical NPs was varied in the experiments. When the initial NPs were of the same type, comprehension was slowed after participants had read the sentence-final verbs, a finding that supports the view that working memory in language comprehension is constrained by similarity-based interference during the retrieval of information necessary to determine the syntactic or semantic relations between noun phrases and verb phrases. Ease of comprehension was also influenced by the association between type of NP and syntactic position, with the best performance being observed when more definite NPs (pronouns and names) were in a prominent syntactic position (e.g., matrix subject) and less definite NPs (descriptions) were in a non-prominent syntactic position (embedded subject). This pattern provides evidence that the interpretation of sentences is facilitated by consistent packaging of information in different linguistic elements. PMID:16970936

Can pictorial warning labels on cigarette packages address smoking-related health disparities?: Field experiments in Mexico to assess warning label content

PubMed Central

Thrasher, James F.; Arillo-Santillán, Edna; Villalobos, Victor; Pérez-Hernández, Rosaura; Hammond, David; Carter, Jarvis; Sebrié, Ernesto; Sansores, Raul; Regalado-Piñeda, Justino

2012-01-01

Objective This study aimed to determine the most effective content of pictorial health warning labels (HWLs) and whether educational attainment moderates these effects. Methods Field experiments were conducted with 529 adult smokers and 530 young adults (258 nonsmokers; 271 smokers), wherein participants reported responses to different HWLs printed on cigarette packages. One experiment involved manipulating textual form (testimonial narrative vs didactic) and the other involved manipulating imagery type (diseased organs vs human suffering). Results Tests of mean ratings and rankings indicated that HWLs with didactic textual forms had equivalent or significantly higher credibility, relevance, and impact than HWLs with testimonial forms. Results from mixed-effects models confirmed these results. However, responses differed by participant educational attainment: didactic forms were consistently rated higher than testimonials among participants with higher education, whereas the difference between didactic and testimonial narrative forms was weaker or not statistically significant among participants with lower education. In the second experiment, with textual content held constant, greater credibility, relevance and impact was found for graphic imagery of diseased organs than imagery of human suffering. Conclusions Pictorial HWLs with didactic textual forms appear to work better than with testimonial narratives. Future research should determine which pictorial HWL content has the greatest real-world impact among consumers from disadvantaged groups, including assessment of how HWL content should change to maintain its impact as tobacco control environments strengthen and consumer awareness of smoking-related risks increases. PMID:22350859

Can pictorial warning labels on cigarette packages address smoking-related health disparities? Field experiments in Mexico to assess pictorial warning label content.

PubMed

Thrasher, James F; Arillo-Santillán, Edna; Villalobos, Victor; Pérez-Hernández, Rosaura; Hammond, David; Carter, Jarvis; Sebrié, Ernesto; Sansores, Raul; Regalado-Piñeda, Justino

2012-03-01

The objective of this study was to determine the most effective content of pictorial health warning labels (HWLs) and whether educational attainment moderates these effects. Field experiments were conducted with 529 adult smokers and 530 young adults (258 nonsmokers; 271 smokers). Participants reported responses to different pictorial HWLs printed on cigarette packages. One experiment involved manipulating textual form (testimonial narrative vs. didactic) and the other involved manipulating image type (diseased organs vs. human suffering). Tests of mean ratings and rankings indicated that pictorial HWLs with didactic textual forms had equivalent or significantly higher credibility, relevance, and impact than pictorial HWLs with testimonial forms. Results from mixed-effects models confirmed these results. However, responses differed by participant educational attainment: didactic forms were consistently rated higher than testimonials among participants with higher education, whereas the difference between didactic and testimonial narrative forms was weaker or not statistically significant among participants with lower education. In the second experiment, with textual content held constant, greater credibility, relevance, and impact was found for graphic imagery of diseased organs than imagery of human suffering. Pictorial HWLs with didactic textual forms seem to work better than those with testimonial narratives. Future research should determine which pictorial HWL content has the greatest real-world impact among consumers from disadvantaged groups, including assessment of how HWL content should change to maintain its impact as tobacco control environments strengthen and consumer awareness of smoking-related risks increases.

Empowering families with the experience of mental illness. A presentation of the Polish version of CAMILLE training package.

PubMed

Tabak, Izabela; Zabłocka-Żytka, Lidia; Czabała, Jan C

2016-01-01

The paper presents the CAMILLE training package prepared in the EU program Empowerment of Children and Adolescents of Mentally Ill Parents through Training of Professionals working with children and adolescents. The training is designed for psychiatrists, psychologists, social workers, teachers and others working with children and adolescents where a parent experiences mental disorders. The project was realized on 4 stages: (1) pre-analyses (quality and quantity) with professionals, family members and people experiencing mental disorders, in regards to the needs, experiences and expectations in education of professionals working with families of parents with mental illness; (2) development of a new pan-European training program for specialists working with these families; (3) pre-pilot implementation and evaluation of the training; (4) preparing of the final version of the training and pilot implementation in 7 countries participating in the project, also in Poland. The training program consists of 9 subjects, divided into 3 main groups: the basic knowledge (mental disorders, child development, attachment), experiences and needs of the families (experiences of parents, children, stigma), methods of family support (talking with children, resilience, successful services). The pilot implementation of the program showed great professionals' interest in the subject and training methods. The evaluation showed significant positive effects of the training in terms of the raise of awareness of influence of the parent's illness on needs of the child, parental abilities and ability of building the child resilience. The CAMILLE training is a valuable program that can be implemented in Poland.

Laboratory Connections: Review of Two Commercial Interfacing Packages.

ERIC Educational Resources Information Center

Powers, Michael H.

1989-01-01

Evaluates two Apple II interfacing packages designed to measure pH: (1) "Experiments in Chemistry" by HRM Software and (2) "Voltage Plotter III" by Vernier Software. Provides characteristics and screen dumps of each package. Reports both systems are suitable for high school or beginning college laboratories. (MVL)

Installation package for concentrating solar collector panels

NASA Technical Reports Server (NTRS)

1978-01-01

The concentrating solar collector panels comprise a complete package array consisting of collector panels using modified Fresnel prismatic lenses for a 10 to 1 concentrating ratio, supporting framework, fluid manifolding and tracking drive system, and unassembled components for field erection.

Consumers' willingness to pay for nutritional claims fighting the obesity epidemic: the case of reduced-fat and low salt cheese in Spain.

PubMed

de-Magistris, T; Lopéz-Galán, B

2016-06-01

The aim of this study was to investigate consumers' willingness to pay (WTP) for cheeses bearing reduced-fat and low salt claims in Spain. An experiment with 219 cheese consumers was conducted in the period March-May 2015. We used different versions of cheese bearing reduced-fat and low salt claims. A choice experiment was used to estimate WTP for reduced-fat and/or low salt cheeses. Participants faced eight choice sets, each consisting of two packages of cheese with different combinations of two claims. Individuals chose one of the two packages of cheese in each choice set, or decided not to choose either. Moreover, to consider possible heterogeneity in WTP across consumers, a random parameters logit model (RPL), a Chi-squared test, and analysis of variance tests were used. Spanish cheese consumers were willing to pay a positive premium for packages of cheese with reduced-fat claims (€0.538/100 g), and for cheese with reduced-fat and low salt claims (€1.15/100 g). Conversely, consumers valued low-salt content claims negatively. They preferred to pay €0.38/100 g for a conventional cheese rather than one low in salt content. As there was heterogeneity in consumers' WTP, two different consumer segments were identified. Segment 1 consisted of normal weight and younger consumers with higher incomes and levels of education, who valued low salt cheese more negatively than those individuals in Segment 2, predominantly comprising overweight and older consumers with low income and educational level. This means that individuals in Segment 1 would pay more for conventional cheese (€1/100 g) than those in Segment 2 (€0.50/100 g). However, no difference between the two segments was found in WTP for reduced-fat cheese. The findings suggest that consumers are willing to pay a price premium for a package of cheese with a reduced-fat claim or cheese with reduced-fat and low salt claims appearing together; however, they are not willing to pay for a package of cheese with only a low salt claim. In comparison with overweight people, normal weight consumers would prefer to pay more for conventional cheese than low salt cheese. Finally, the results of this study contribute to insights in the promotion of healthier food choices among consumers. In this regard, outreach activities promoted by food companies could drive consumers to increase their knowledge of the benefits of eating reduced-fat and low salt food products in relation to their health status. Copyright © 2016 The Royal Society for Public Health. Published by Elsevier Ltd. All rights reserved.

Sterilization of medical equipment and contaminated articles by making use of a resistive barrier discharge

NASA Astrophysics Data System (ADS)

Uhm, Han S.; Kang, Jung G.; Choi, Eun H.; Cho, Guang S.

2012-08-01

Presented here is an apparatus consisting of an atmospheric resistive-barrier discharge for the sterilization of medical tools wrapped in typical hospital cloths, for the sterilization of manufactured drugs in typical packaging materials, and for the sterilization of biologically-contaminated articles. The sterilization apparatus consists of layers of the resistive-barrier discharge device operating at room temperature, a sterilization chamber, and an ozone destruction device. An electrical discharge in the resistive-barrier discharge system generates an atmospheric plasma in oxygen gas, generating ozone, which in turn efficiently sterilizes medical tools and biologically contaminated articles at room temperature. A sterilization experiment was carried out at an apparatus volume of 100 liters, with a sterilization chamber volume of 60 liters, and a discharge device volume of 40 liters. The sterilization in this experiment required 60 W of power for 5 hours of residence time. For a given sterilization time, the required electrical power was proportional to the apparatus volume. Ozone in the sterilization chamber was destroyed safely after sterilization.

Development of an Environmental Monitoring Package for the International Space Station

NASA Technical Reports Server (NTRS)

Carruth, Ralph M., Jr.; Clifton, Kenneth S.; Vanhooser, Michael T.

1999-01-01

The first elements of the International Space Station (ISS) will soon be launched into space and over the next few years ISS will be assembled on orbit into its final configuration. Experiments will be performed on a continuous basis both inside and outside the station. External experiments will be mounted on attached payload locations specifically designed to accommodate experiments and provide data and power from ISS. From the beginning of the space station program it has been recognized that external experiments will require knowledge of the external environment because it can affect the science being performed and may impact lifetime and operations of the experiments. Recently an effort was initiated to design and develop an Environment Monitoring Package (EMP) was started. This paper describes the derivation of the requirements for the EMP package, the type of measurements that the EMP will make and types of instruments which will be employed to make these measurements.

An Environment Monitoring Package for the International Space Station

NASA Technical Reports Server (NTRS)

Carruth, M. Ralph; Clifton, Kenneth S.

1998-01-01

The first elements of the International Space Station (ISS) will soon be launched into space and over the next few years ISS will be assembled on orbit into its final configuration. Experiments will be performed on a continuous basis both inside and outside the station. External experiments will be mounted on attached payload locations specifically designed to accommodate experiments, provide data and supply power from ISS. From the beginning of the space station program it has been recognized that experiments will require knowledge of the external local environment which can affect the science being performed and may impact lifetime and operations of the experiment hardware. Recently an effort was initiated to design and develop an Environment Monitoring Package (EMP). This paper describes the derivation of the requirements for the EMP package, the type of measurements that the EMP will make and types of instruments which will be employed to make these measurements.

Apollo 17 Lunar Surface Experiment equipment

NASA Image and Video Library

1972-11-30

S72-37259 (November 1972) --- The Geophone Module and Cable Reels of the Lunar Seismic Profiling Experiment (S-203), a component of the Apollo Lunar Surface Experiments Package which will be carried on the Apollo 17 lunar landing mission. LSPE components are four geophones similar to those used in an earlier active seismic experiment, an electronics package in the ALSEP central station, and eight explosive packages which will be deployed during the geology traverse. The four geophones will be placed one in the center and one at each corner of a 90-meter equilateral triangle. Explosive charges placed on the surface will generate seismic waves of varying strengths to provide data on the structural profile of the landing site. After the charges have been fired by ground command, the experiment will settle down into a passive listening mode, detecting moonquakes, meteorite impacts and the thump caused by the Lunar Module ascent stage impact.

Development and Use of an Open-Source, User-Friendly Package to Simulate Voltammetry Experiments

ERIC Educational Resources Information Center

Wang, Shuo; Wang, Jing; Gao, Yanjing

2017-01-01

An open-source electrochemistry simulation package has been developed that simulates the electrode processes of four reaction mechanisms and two typical electroanalysis techniques: cyclic voltammetry and chronoamperometry. Unlike other open-source simulation software, this package balances the features with ease of learning and implementation and…

Net costs of health worker rural incentive packages: an example from the Lao People's Democratic Republic.

PubMed

Keuffel, Eric; Jaskiewicz, Wanda; Paphassarang, Chanthakhath; Tulenko, Kate

2013-11-01

Many developing countries are examining whether to institute incentive packages that increase the share of health workers who opt to locate in rural settings; however, uncertainty exists with respect to the expected net cost (or benefit) from these packages. We utilize the findings from the discrete choice experiment surveys applied to students training to be health professionals and costing analyses in Lao People's Democratic Republic to model the anticipated effect of incentive packages on new worker location decisions and direct costs. Incorporating evidence on health worker density and health outcomes, we then estimate the expected 5-year net cost (or benefit) of each incentive packages for 3 health worker cadres--physicians, nurses/midwives, and medical assistants. Under base case assumptions, the optimal incentive package for each cadre produced a 5-year net benefit (maximum net benefit for physicians: US$ 44,000; nurses/midwives: US$ 5.6 million; medical assistants: US$ 485,000). After accounting for health effects, the expected net cost of select incentive packages would be substantially less than the original estimate of direct costs. In the case of Lao People's Democratic Republic, incentive packages that do not invest in capital-intensive components generally should produce larger net benefits. Combining discrete choice experiment surveys, costing surveys and cost-benefit analysis methods may be replicated by other developing countries to calculate whether health worker incentive packages are viable policy options.

ERTS-C (Landsat 3) cryogenic heat pipe experiment definition

NASA Technical Reports Server (NTRS)

Brennan, P. J.; Kroliczek, E. J.

1975-01-01

A flight experiment designed to demonstrate current cryogenic heat pipe technology was defined and evaluated. The experiment package developed is specifically configured for flight aboard an ERTS type spacecraft. Two types of heat pipes were included as part of the experiment package: a transporter heat pipe and a thermal diode heat pipe. Each was tested in various operating modes. Performance data obtained from the experiment are applicable to the design of cryogenic systems for detector cooling, including applications where periodic high cooler temperatures are experienced as a result of cyclic energy inputs.

An Experimental Study of Diffusivity of Technetium-99 in Hanford Vadose Zone Sediments

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mattigod, Shas V.; Bovaird, Chase C.; Wellman, Dawn M.

2012-11-01

One of the methods being considered at the Hanford site in Washington for safely disposing of low-level radioactive wastes (LLW) is to encase the waste in concrete and entomb the packages in the Hanford vadose zone sediments. The current plan for waste isolation consists of stacking low-level waste packages on a trench floor, surrounding the stacks with reinforced steel, and encasing these packages with concrete. Any failure of the concrete encasement may result in water intrusion and consequent mobilization of radionuclides from the waste packages. The mobilized radionuclides may escape from the encased concrete by mass flow and/or diffusion andmore » move into the surrounding subsurface sediments. It is therefore necessary to conduct an assessment of the performance of the concrete encasement structure and the surrounding soil’s ability to retard radionuclide migration. The retardation factors for radionuclides contained in the waste packages can be determined from measurements of diffusion coefficients for these contaminants through concrete and fill material. Because of their anionic nature in aqueous solutions, the radionuclides, 99Tc and 129I were identified as long-term dose contributors in LLW. The leachability and/or diffusion of these radionuclide species must be measured in order to assess the long-term performance of waste grouts when contacted with vadose-zone porewater or groundwater. To measure the diffusivity, a set of experiments were conducted using 99Tc-spiked concrete (with 0 and 4% metallic iron additions) in contact with unsaturated soil half-cells that reflected the typical moisture contents of Hanford vadose zone sediments. The 99Tc diffusion profiles in the soil half cells were measured after a time lapse of ~1.9 yr. Using the concentration profiles, the 99Tc diffusivity coefficients were calculated based on Fick’s Second Law.« less

Packaging's Contribution for the Effectiveness of the Space Station's Food Service Operation

NASA Technical Reports Server (NTRS)

Rausch, B. A.

1985-01-01

Storage limitations will have a major effect on space station food service. For example: foods with low bulk density such as ice cream, bread, cake, standard type potato chips and other low density snacks, flaked cereals, etc., will exacerbate the problem of space limitations; package containers are inherently volume consuming and refuse creating; and the useful observation that the optimum package is no package at all leads to the tentative conclusion that the least amount of packaging per unit of food, consistent with storage, aesthetics, preservation, cleanliness, cost and disposal criteria, is the most practical food package for the space station. A series of trade offs may have to be made to arrive at the most appropriate package design for a particular type of food taking all the criteria into account. Some of these trade offs are: single serve vs. bulk; conventional oven vs. microwave oven; nonmetallic aseptically vs. non-aseptically packaged foods; and comparison of aseptic vs. nonaseptic food packages. The advantages and disadvantages are discussed.

smwrGraphs—An R package for graphing hydrologic data, version 1.1.2

USGS Publications Warehouse

Lorenz, David L.; Diekoff, Aliesha L.

2017-01-31

This report describes an R package called smwrGraphs, which consists of a collection of graphing functions for hydrologic data within R, a programming language and software environment for statistical computing. The functions in the package have been developed by the U.S. Geological Survey to create high-quality graphs for publication or presentation of hydrologic data that meet U.S. Geological Survey graphics guidelines.

Romanian experience on packaging testing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vieru, G.

2007-07-01

With more than twenty years ago, the Institute for Nuclear Research Pitesti (INR), through its Reliability and Testing Laboratory, was licensed by the Romanian Nuclear Regulatory Body- CNCAN and to carry out qualification tests [1] for packages intended to be used for the transport and storage of radioactive materials. Radioactive materials, generated by Romanian nuclear facilities [2] are packaged in accordance with national [3] and the IAEA's Regulations [1,6] for a safe transport to the disposal center. Subjecting these packages to the normal and simulating test conditions accomplish the evaluation and certification in order to prove the package technical performances.more » The paper describes the qualification tests for type A and B packages used for transport and storage of radioactive materials, during a period of 20 years of experience. Testing is used to substantiate assumption in analytical models and to demonstrate package structural response. The Romanian test facilities [1,3,6] are used to simulate the required qualification tests and have been developed at INR Pitesti, the main supplier of type A packages used for transport and storage of low radioactive wastes in Romania. The testing programme will continue to be a strong option to support future package development, to perform a broad range of verification and certification tests on radioactive material packages or component sections, such as packages used for transport of radioactive sources to be used for industrial or medical purposes [2,8]. The paper describes and contain illustrations showing some of the various tests packages which have been performed during certain periods and how they relate to normal conditions and minor mishaps during transport. Quality assurance and quality controls measures taken in order to meet technical specification provided by the design there are also presented and commented. (authors)« less

The DOSIS and DOSIS 3D Experiments onboard the International Space Station - Results from the Active DOSTEL Instruments

NASA Astrophysics Data System (ADS)

Burmeister, Soenke; Berger, Thomas; Reitz, Guenther; Beaujean, Rudolf; Boehme, Matthias; Haumann, Lutz; Labrenz, Johannes; Kortmann, Onno

2012-07-01

Besides the effects of the microgravity environment, and the psychological and psychosocial problems experienced in confined spaces, radiation is the main health detriment for long duration human space missions. The radiation environment encountered in space differs in nature from that on earth, consisting mostly of high energetic ions from protons up to iron, resulting in radiation levels far exceeding the ones present on earth for occupational radiation workers. Accurate knowledge of the physical characteristics of the space radiation field in dependence on the solar activity, the orbital parameters and the different shielding configurations of the International Space Station ISS is therefore needed. For the investigation of the spatial and temporal distribution of the radiation field inside the European COLUMBUS module the experiment DOSIS (Dose Distribution Inside the ISS) under the lead of DLR was launched on July 15th 2009 with STS-127 to the ISS. The experimental package was transferred from the Space Shuttle into COLUMBUS on July 18th. It consists of a combination of passive detector packages (PDP) distributed at 11 locations inside the European Columbus Laboratory and two active radiation detectors (DOSTELs) with a DDPU (DOSTEL Data and Power Unit) in a nomex pouch (DOSIS MAIN BOX) mounted at a fixed location beneath the European Physiology Module rack (EPM) inside COLUMBUS. The DOSTELs measured during the lowest solar minimum conditions in the space age from July 18th 2009 to June 16th 2011. In July 2011 the active hardware was transferred to ground for refurbishment and preparation for the DOSIS-3D experiment. The hardware will be launched with the Soyuz 30S flight to the ISS on May 15th 2012 and activated approximately ten days later. Data will be transferred from the DOSTEL units to ground via the EPM rack which is activated approximately every four weeks for this action. First Results for the active DOSIS-3D measurements such as count rate profiles, dose rates and LET spectra will be presented in comparison to the data of the DOSIS experiment as well as the DOSMAP experiment which has been performed during solar maximum in 2001.

Response of CO2 laser written long period fiber gratings packaged by polymer materials

NASA Astrophysics Data System (ADS)

Wu, Zhaodi; Liu, Yunqi; Zou, Jian; Chen, Na; Pang, Fufei; Wang, Tingyun

2011-12-01

We demonstrate the packaging of CO2 laser written long-period fiber gratings (LPFGs) using different polymer materials. We use three different silicone rubber polymers to package the LPFGs by simply coating it outside the grating. After the polymer coating, the resonance wavelength of LPFG was found to shift towards shorter wavelength by about 6 nm, and the temperature sensitivity of the packaged gratings was studied experimentally. Experiments showed that the gratings packaged by different polymers have different temperature characteristics and all of them have good thermal stability.

Mechanical-Electrochemical-Thermal Simulation of Lithium-Ion Cells

DOE Office of Scientific and Technical Information (OSTI.GOV)

Santhanagopalan, Shriram; Zhang, Chao; Sprague, Michael A.

2016-06-01

Models capture the force response for single-cell and cell-string levels to within 15%-20% accuracy and predict the location for the origin of failure based on the deformation data from the experiments. At the module level, there is some discrepancy due to poor mechanical characterization of the packaging material between the cells. The thermal response (location and value of maximum temperature) agrees qualitatively with experimental data. In general, the X-plane results agree with model predictions to within 20% (pending faulty thermocouples, etc.); the Z-plane results show a bigger variability both between the models and test-results, as well as among multiple repeatsmore » of the tests. The models are able to capture the timing and sequence in voltage drop observed in the multi-cell experiments; the shapes of the current and temperature profiles need more work to better characterize propagation. The cells within packaging experience about 60% less force under identical impact test conditions, so the packaging on the test articles is robust. However, under slow-crush simulations, the maximum deformation of the cell strings with packaging is about twice that of cell strings without packaging.« less

MSUSTAT.

ERIC Educational Resources Information Center

Mauriello, David

1984-01-01

Reviews an interactive statistical analysis package (designed to run on 8- and 16-bit machines that utilize CP/M 80 and MS-DOS operating systems), considering its features and uses, documentation, operation, and performance. The package consists of 40 general purpose statistical procedures derived from the classic textbook "Statistical…

Sharing brain mapping statistical results with the neuroimaging data model

PubMed Central

Maumet, Camille; Auer, Tibor; Bowring, Alexander; Chen, Gang; Das, Samir; Flandin, Guillaume; Ghosh, Satrajit; Glatard, Tristan; Gorgolewski, Krzysztof J.; Helmer, Karl G.; Jenkinson, Mark; Keator, David B.; Nichols, B. Nolan; Poline, Jean-Baptiste; Reynolds, Richard; Sochat, Vanessa; Turner, Jessica; Nichols, Thomas E.

2016-01-01

Only a tiny fraction of the data and metadata produced by an fMRI study is finally conveyed to the community. This lack of transparency not only hinders the reproducibility of neuroimaging results but also impairs future meta-analyses. In this work we introduce NIDM-Results, a format specification providing a machine-readable description of neuroimaging statistical results along with key image data summarising the experiment. NIDM-Results provides a unified representation of mass univariate analyses including a level of detail consistent with available best practices. This standardized representation allows authors to relay methods and results in a platform-independent regularized format that is not tied to a particular neuroimaging software package. Tools are available to export NIDM-Result graphs and associated files from the widely used SPM and FSL software packages, and the NeuroVault repository can import NIDM-Results archives. The specification is publically available at: http://nidm.nidash.org/specs/nidm-results.html. PMID:27922621

NLM microcomputer-based tutorials (for microcomputers). Software

DOE Office of Scientific and Technical Information (OSTI.GOV)

Perkins, M.

1990-04-01

The package consists of TOXLEARN--a microcomputer-based training package for TOXLINE (Toxicology Information Online), CHEMLEARN-a microcomputer-based training package for CHEMLINE (Chemical Information Online), MEDTUTOR--a microcomputer-based training package for MEDLINE (Medical Information Online), and ELHILL LEARN--a microcomputer-based training package for the ELHILL search and retrieval software that supports the above-mentioned databases...Software Description: The programs were developed under PILOTplus using the NLM LEARN Programmer. They run on IBM-PC, XT, AT, PS/2, and fully compatible computers. The programs require 512K RAM memory, one disk drive, and DOS 2.0 or higher. The software supports most monochrome, color graphics, enhanced color graphics, or visual graphics displays.

SuperLab LT: Evaluation and Uses in Teaching Experimental Psychology

ERIC Educational Resources Information Center

Ragozzine, Frank

2002-01-01

I describe and evaluate SuperLab LT (Chase & Abboud, 1990), a software package that enables students to replicate classic experiments in cognitive psychology. I also discuss the package with respect to its uses in teaching an undergraduate course in Experimental Psychology. Although the package has minor flaws, SuperLab LT provides numerous…

Evaluation of a Multicomponent Intervention Package to Increase Summer Work Experiences for Transition-Age Youth with Severe Disabilities

ERIC Educational Resources Information Center

Carter, Erik W.; Trainor, Audrey A.; Ditchman, Nicole; Swedeen, Beth; Owens, Laura

2009-01-01

Early work experiences have been advocated as an important avenue for equipping youth with disabilities with the skills, attitudes, opportunities, and aspirations needed to transition successfully to meaningful careers after high school. We examined the efficacy and social validity of a multicomponent intervention package--composed of…

Colour of ground beef as influenced by raw materials, addition of sodium chloride and low oxygen packaging.

PubMed

Sørheim, O; Westad, F; Larsen, H; Alvseike, O

2009-03-01

The study aimed at examining the effects of freezing of raw materials, holding time for fresh raw materials post mortem and addition of 0.5-1.0% NaCl on the colour of ground beef under low oxygen (O2) modified atmosphere storage. The samples were exposed to 0.1-3.0% O2 at 4°C for up to 10 days, and analysed for O2 concentrations, instrumental and visual colour. Residual O2 in the headspace of the packages oxidizes myoglobin and discolours the meat. Meat may have the ability to scavenge residual O2, and ground beef differs from intact muscles by having a much higher capacity for O2 consumption. In this experiment, the use of frozen/thawed raw materials and addition of NaCl both decreased the rate of O2 consumption and increased discolouration. Using raw materials from 2 days rather than 7 days post mortem greatly increased the rate of removal of O2 and improved redness. In low O2 packaging, ground beef preferably should be stored for at least 2 days in an atmosphere with less than 0.1% residual O2 to produce a purple pigment predominantly consisting of deoxymyoglobin.

Preparing safety data packages for experimenters using the Get Away Special (GAS) carrier system

NASA Technical Reports Server (NTRS)

Kosko, Jerome

1992-01-01

The implementation of NSTS 1700.7B and more forceful scruntiny of data packages by the Johnson Space Flight Center (JSC) lead to the development of a classification policy for GAS/CAP payloads. The purpose of this policy is to classify experiments using the carrier system so that they receive an appropriate level of JSC review (i.e., one or multiphase reviews). This policy is based on energy containment to show inherent payload safety. It impacts the approach to performing hazard analyses and the nature of the data package. This paper endeavors to explain the impact of this policy as well as the impact of recent JSC as well as Kennedy Space Flight Center (KSC) 'interpretations' of existing requirements. The GAS canister does adequately contain most experiments when flown in the sealed configuration (however this must be shown, not merely stated). This paper also includes data package preparation guidelines for those experiments that require an opening door which often present unique safety issues.

JUICE: A European Mission to Jupiter and its Icy Moons

NASA Astrophysics Data System (ADS)

Grasset, Olivier; Witasse, Olivier; Barabash, Stas; Brandt, Pontus; Bruzzone, Lorenzo; Bunce, Emma; Cecconi, Baptiste; Cavalié, Thibault; Cimo, Giuseppe; Coustenis, Athena; Cremonese, Gabriele; Dougherty, Michele; Fletcher, Leigh N.; Gladstone, Randy; Gurvits, Leonid; Hartogh, Paul; Hoffmann, Holger; Hussmann, Hauke; Iess, Luciano; Jaumann, Ralf; Kasaba, Yasumasa; Kaspi, Yohai; Krupp, Norbert; Langevin, Yves; Mueller-Wodarg, Ingo; Palumbo, Pasquale; Piccioni, Giuseppe; Plaut, Jeffrey; Poulet, Francois; Roatsch, Thomas; Retherford, Kurt D.; Rothkaehl, Hanna; Stevenson, David J.; Tosi, Federico; Van Hoolst, Tim; Wahlund, Jan-Erik; Wurz, Peter; Altobelli, Nicolas; Accomazzo, A.; Boutonnet, Arnaud; Erd, Christian; Vallat, Claire

2016-10-01

JUICE - JUpiter ICy moons Explorer - is the first large mission in the ESA Cosmic Vision programme [1]. The implementation phase started in July 2015. JUICE will arrive at Jupiter in October 2029, and will spend 3 years characterizing the Jovian system, the planet itself, its giant magnetosphere, and the giant icy moons: Ganymede, Callisto and Europa. JUICE will then orbit Ganymede.The first goal of JUICE is to explore the habitable zone around Jupiter [2]. Ganymede is a high-priority target because it provides a unique laboratory for analyzing the nature, evolution and habitability of icy worlds, including the characteristics of subsurface oceans, and because it possesses unique magnetic fields and plasma interactions with the environment. On Europa, the focus will be on recently active zones, where the composition, surface and subsurface features (including putative water reservoirs) will be characterized. Callisto will be explored as a witness of the early Solar System.JUICE will also explore the Jupiter system as an archetype of gas giants. The circulation, meteorology, chemistry and structure of the Jovian atmosphere will be studied from the cloud tops to the thermosphere and ionosphere. JUICE will investigate the 3D properties of the magnetodisc, and study the coupling processes within the magnetosphere, ionosphere and thermosphere. The mission also focuses on characterizing the processes that influence surface and space environments of the moons.The payload consists of 10 instruments plus a ground-based experiment (PRIDE) to better constrain the S/C position. A remote sensing package includes imaging (JANUS) and spectral-imaging capabilities from UV to sub-mm wavelengths (UVS, MAJIS, SWI). A geophysical package consists of a laser altimeter (GALA) and a radar sounder (RIME) for exploring the moons, and a radio science experiment (3GM) to probe the atmospheres and to determine the gravity fields. The in situ package comprises a suite to study plasma and neutral gas environments (PEP) with remote sensing capabilities via energetic neutrals, a magnetometer (J-MAG) and a radio and plasma wave instrument (RPWI). [1] JUICE Definition Study Report, ESA/SRE(2014)1. [2] Grasset et al., Plan. Space Sci., 78, 2013

ATIC Flight Data Processing

NASA Technical Reports Server (NTRS)

Ahn, H. S.; Adams, James H., Jr.; Bashindzhagyan, G.; Ampe, J.; Case, G.; Whitaker, Ann F. (Technical Monitor)

2001-01-01

The first flight of the Advanced Thin Ionization Calorimeter (ATIC) experiment from McMurdo, Antarctica lasted for 16 days, starting on December 28, 2000. The ATIC instrument consists of a fully active 320-crystal, 960-channel Bismuth Germanate (BGO) calorimeter, 202 scintillator strips (808 channels) in 3 hodoscopes, interleaved with graphite target layers, and a 4480-pixel silicon matrix charge detector. We have developed an object-oriented data processing package based on ROOT. In this paper, we describe the data processing scheme used in handling the accumulated 45 GB of flight data. We discuss calibration issues, particularly the time-dependence of housekeeping information.

STS-39 AFP-675 and STP-1 MPESS in OV-103's payload bay (PLB)

NASA Image and Video Library

1991-05-06

STS039-10-019 (28 April-6 May 1991) --- This 35mm frame, taken from inside the crew cabin, shows some of the cargo in Discovery's payload bay. Seen are the tops of canisters on the STP-1 payload, configured on the STS 39 Hitchhiker carrier; and the Air Force Program (AFP) 675 package. AFP-675 consists of the Cryogenic Infrared Radiance Instrumentation for Shuttle (CIRRIS)-1A; Far Ultraviolet Camera (FAR-UV) Experiment; Horizon Ultraviolet Program (HUP); Quadruple Ion Neutral Mass Spectrometer (QINMS); and the Uniformly Redundant Array (URA).

STS-39 OV-103 reaction control system (RCS) jets fire during onorbit maneuver

NASA Image and Video Library

1991-05-06

STS039-27-016 (28 April-6 May 1991) --- The Space Shuttle Discovery fires reaction control subsystem (RCS) thrusters in this 35mm frame, taken from inside the crew cabin. Seen in Discovery's payload bay are the tops of cannisters on the STP-1 payload, configured on the STS 39 Hitchhiker carrier; and the Air Force Program (AFP) 675 package. AFP-675 consists of the Cryogenic Infrared Radiance Instrumentation for Shuttle (CIRRIS)-1A; Far Ultraviolet Camera (FAR-UV) Experiment; Horizon Ultraviolet Program (HUP); Quadruple Ion Neutral Mass Spectrometer (QINMS); and the Uniformly Redundant Array (URA).

The Ocean Observatories Initiative: Data Acquisition Functions and Its Built-In Automated Python Modules

NASA Astrophysics Data System (ADS)

Smith, M. J.; Vardaro, M.; Crowley, M. F.; Glenn, S. M.; Schofield, O.; Belabbassi, L.; Garzio, L. M.; Knuth, F.; Fram, J. P.; Kerfoot, J.

2016-02-01

The Ocean Observatories Initiative (OOI), funded by the National Science Foundation, provides users with access to long-term datasets from a variety of oceanographic sensors. The Endurance Array in the Pacific Ocean consists of two separate lines off the coasts of Oregon and Washington. The Oregon line consists of 7 moorings, two cabled benthic experiment packages and 6 underwater gliders. The Washington line comprises 6 moorings and 6 gliders. Each mooring is outfitted with a variety of instrument packages. The raw data from these instruments are sent to shore via satellite communication and in some cases, via fiber optic cable. Raw data is then sent to the cyberinfrastructure (CI) group at Rutgers where it is aggregated, parsed into thousands of different data streams, and integrated into a software package called uFrame. The OOI CI delivers the data to the general public via a web interface that outputs data into commonly used scientific data file formats such as JSON, netCDF, and CSV. The Rutgers data management team has developed a series of command-line Python tools that streamline data acquisition in order to facilitate the QA/QC review process. The first step in the process is querying the uFrame database for a list of all available platforms. From this list, a user can choose a specific platform and automatically download all available datasets from the specified platform. The downloaded dataset is plotted using a generalized Python netcdf plotting routine that utilizes a data visualization toolbox called matplotlib. This routine loads each netCDF file separately and outputs plots by each available parameter. These Python tools have been uploaded to a Github repository that is openly available to help facilitate OOI data access and visualization.

Analysis of counting data: Development of the SATLAS Python package

NASA Astrophysics Data System (ADS)

Gins, W.; de Groote, R. P.; Bissell, M. L.; Granados Buitrago, C.; Ferrer, R.; Lynch, K. M.; Neyens, G.; Sels, S.

2018-01-01

For the analysis of low-statistics counting experiments, a traditional nonlinear least squares minimization routine may not always provide correct parameter and uncertainty estimates due to the assumptions inherent in the algorithm(s). In response to this, a user-friendly Python package (SATLAS) was written to provide an easy interface between the data and a variety of minimization algorithms which are suited for analyzinglow, as well as high, statistics data. The advantage of this package is that it allows the user to define their own model function and then compare different minimization routines to determine the optimal parameter values and their respective (correlated) errors. Experimental validation of the different approaches in the package is done through analysis of hyperfine structure data of 203Fr gathered by the CRIS experiment at ISOLDE, CERN.

Independent Orbiter Assessment (IOA): Analysis of the Orbiter Experiment (OEX) subsystem

NASA Technical Reports Server (NTRS)

Compton, J. M.

1987-01-01

The results of the Independent Orbiter Assessment (IOA) of the Failure Modes and Effects Analysis (FMEA) and Critical Items List (CIL) are presented. The IOA approach features a top-down analysis of the hardware to determine failure modes, criticality, and potential critical items. To preserve independence, this analysis was accomplished without reliance upon the results contained within the NASA FMEA/CIL documentation. This report documents the independent analysis results corresponding to the Orbiter Experiments hardware. Each level of hardware was evaluated and analyzed for possible failure modes and effects. Criticality was assigned based upon the severity of the effect for each failure mode. The Orbiter Experiments (OEX) Program consists of a multiple set of experiments for the purpose of gathering environmental and aerodynamic data to develop more accurate ground models for Shuttle performance and to facilitate the design of future spacecraft. This assessment only addresses currently manifested experiments and their support systems. Specifically this list consists of: Shuttle Entry Air Data System (SEADS); Shuttle Upper Atmosphere Mass Spectrometer (SUMS); Forward Fuselage Support System for OEX (FFSSO); Shuttle Infrared Laced Temperature Sensor (SILTS); Aerodynamic Coefficient Identification Package (ACIP); and Support System for OEX (SSO). There are only two potential critical items for the OEX, since the experiments only gather data for analysis post mission and are totally independent systems except for power. Failure of any experiment component usually only causes a loss of experiment data and in no way jeopardizes the crew or mission.

IEEE WMED 2016 Homepage

Science.gov Websites

characterization, design, and new device technologies. This workshop will consist of invited talks, contributed and Reliability Semiconductor package reliability, Design for Manufacturability, Stacked die packaging and Novel assembly processes Microelectronic Circuit Design New product design, high-speed and/or low

7 CFR 993.22 - Consumer package.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 8 2010-01-01 2010-01-01 false Consumer package. 993.22 Section 993.22 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements... weight of mixed dried fruit in the lot consists of standard processed prunes or standard prunes. ...

7 CFR 993.22 - Consumer package.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 8 2011-01-01 2011-01-01 false Consumer package. 993.22 Section 993.22 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements... weight of mixed dried fruit in the lot consists of standard processed prunes or standard prunes. ...

Multipurpose electric furnace system. [for use in Apollo-Soyuz Test Program

NASA Technical Reports Server (NTRS)

Mazelsky, R.; Duncan, C. S.; Seidensticker, R. G.; Johnson, R. A.; Mchugh, J. P.; Foust, H. C.; Piotrowski, P. A.

1974-01-01

A multipurpose electric furnace system of advanced design for space applications was developed and tested. This system is intended for use in the Apollo-Soyuz Test Program. It consists of the furnace, control package and a helium package for rapid cooldown.

The Environmental Data Initiative data repository: Trustworthy practices that foster preservation, fitness, and reuse for environmental and ecological data

NASA Astrophysics Data System (ADS)

Servilla, M. S.; Brunt, J.; Costa, D.; Gries, C.; Grossman-Clarke, S.; Hanson, P. C.; O'Brien, M.; Smith, C.; Vanderbilt, K.; Waide, R.

2017-12-01

The Environmental Data Initiative (EDI) is an outgrowth of more than 30 years of information management experience and technology from LTER Network data practitioners. EDI builds upon the PASTA data repository software used by the LTER Network Information System and manages more than 42,000 data packages, containing tabular data, imagery, and other formats. Development of the repository was a community process beginning in 2009 that included numerous working groups for generating use cases, system requirements, and testing of completed software, thereby creating a vested interested in its success and transparency in design. All software is available for review on GitHub, and refinements and new features are ongoing. Documentation is also available on Read-the-docs, including a comprehensive description of all web-service API methods. PASTA is metadata driven and uses the Ecological Metadata Language (EML) standard for describing environmental and ecological data; a simplified Dublin Core document is also available for each data package. Data are aggregated into packages consisting of metadata and other related content described by an OAI-ORE document. Once archived, each data package becomes immutable and permanent; updates are possible through the addition of new revisions. Components of each data package are accessible through a unique identifier, while the entire data package receives a DOI that is registered in DataCite. Preservation occurs through a combination of DataONE synchronization/replication and by a series of local and remote backup strategies, including daily uploads to AWS Glacier storage. Checksums are computed for all data at initial upload, with random verification occurring on a continuous basis, thus ensuring the integrity of data. PASTA incorporates a series of data quality tests to ensure that data are correctly documented with EML before data are archived; data packages that fail any test are forbidden in the repository. These tests are a measure data fitness, which ultimately increases confidence in data reuse and synthesis. The EDI data repository is recognized by multiple organizations, including EarthCube's Council of Data Facilities, the United States Geological Survey, FAIRsharing.org, re3data.org, and is a PLOS and Nature recommended data repository.

The SEIS Experiment: A Mars Seismic Package

NASA Technical Reports Server (NTRS)

Schibler, P.; Lognonne, P.; Giardini, D.; Banerdt, B.; Karczewski, J. F.; Mimoun, D.; Zweifel, P.; Pike, T.; Ammann, J.; Anglade, A.

2003-01-01

This experiment will integrate a VBB (Very Broad Band) two axis seismometer, a three axis Short Period seismometer and a series of environmental sensors for pressure, infra-sounds and temperature. IPGP (France) has the overall responsibility of the experiment and is responsible for the VBB and environmental sensors. ETHZ (Switzerland) is responsible for the electronics of the experiment and JPL (USA) for the SP (Short Period) sensors. SEIS instrument was first proposed and accepted for NetLander mission (and will also be in charge of data acquisition for SPICE experiment). This seismic package should also be proposed for future missions.

Test Package Plummets in the Zero Gravity Research Facility

NASA Image and Video Library

1966-09-21

National Aeronautics and Space Administration (NASA) Lewis Research Center. Lewis researchers had been studying the behavior of liquid in microgravity for several years using ballistic rocket flights, aircraft flying series of parabolas, and in the 2.2-Second Drop Tower. It was easier to control experiments and repeat tests based on almost instantaneous test results in the Zero Gravity Research Facility than missiles or aircraft. It also more than doubled the microgravity time of the original drop tower. The experiments were enclosed in a large experiment package that was suspended inside the chamber. A vacuum was introduced to the chamber before the package was released. The test equipment allowed researchers to film and take measurements of the experiment as it was falling. The 2500‐pound package was slowed by special Styrofoam‐like pellets in a decelerator cart. An experiment, traveling 176 feet per second, was stopped in about 15 feet of deceleration material. The facility’s designers struggled to determine the correct type of deceleration pellets to use. For several years Lewis engineers tested various samples from manufacturers. The final selection was not made until the facility’s completion in May 1966, just before the facility made its public debut at the 1966 Inspection of the Center.

Combination HIV prevention among MSM in South Africa: results from agent-based modeling.

PubMed

Brookmeyer, Ron; Boren, David; Baral, Stefan D; Bekker, Linda-Gail; Phaswana-Mafuya, Nancy; Beyrer, Chris; Sullivan, Patrick S

2014-01-01

HIV prevention trials have demonstrated the effectiveness of a number of behavioral and biomedical interventions. HIV prevention packages are combinations of interventions and offer potential to significantly increase the effectiveness of any single intervention. Estimates of the effectiveness of prevention packages are important for guiding the development of prevention strategies and for characterizing effect sizes before embarking on large scale trials. Unfortunately, most research to date has focused on testing single interventions rather than HIV prevention packages. Here we report the results from agent-based modeling of the effectiveness of HIV prevention packages for men who have sex with men (MSM) in South Africa. We consider packages consisting of four components: antiretroviral therapy for HIV infected persons with CD4 count <350; PrEP for high risk uninfected persons; behavioral interventions to reduce rates of unprotected anal intercourse (UAI); and campaigns to increase HIV testing. We considered 163 HIV prevention packages corresponding to different intensity levels of the four components. We performed 2252 simulation runs of our agent-based model to evaluate those packages. We found that a four component package consisting of a 15% reduction in the rate of UAI, 50% PrEP coverage of high risk uninfected persons, 50% reduction in persons who never test for HIV, and 50% ART coverage over and above persons already receiving ART at baseline, could prevent 33.9% of infections over 5 years (95% confidence interval, 31.5, 36.3). The package components with the largest incremental prevention effects were UAI reduction and PrEP coverage. The impact of increased HIV testing was magnified in the presence of PrEP. We find that HIV prevention packages that include both behavioral and biomedical components can in combination prevent significant numbers of infections with levels of coverage, acceptance and adherence that are potentially achievable among MSM in South Africa.

Optomechanical Design and Characterization of a Printed-Circuit-Board-Based Free-Space Optical Interconnect Package

NASA Astrophysics Data System (ADS)

Zheng, Xuezhe; Marchand, Philippe J.; Huang, Dawei; Kibar, Osman; Ozkan, Nur S. E.; Esener, Sadik C.

1999-09-01

We present a proof of concept and a feasibility demonstration of a practical packaging approach in which free-space optical interconnects (FSOI s) can be integrated simply on electronic multichip modules (MCM s) for intra-MCM board interconnects. Our system-level packaging architecture is based on a modified folded 4 f imaging system that has been implemented with only off-the-shelf optics, conventional electronic packaging, and passive-assembly techniques to yield a potentially low-cost and manufacturable packaging solution. The prototypical system as built supports 48 independent FSOI channels with 8 separate laser and detector chips, for which each chip consists of a one-dimensional array of 12 devices. All the chips are assembled on a single substrate that consists of a printed circuit board or a ceramic MCM. Optical link channel efficiencies of greater than 90% and interchannel cross talk of less than 20 dB at low frequency have been measured. The system is compact at only 10 in. 3 (25.4 cm 3 ) and is scalable, as it can easily accommodate additional chips as well as two-dimensional optoelectronic device arrays for increased interconnection density.

Experiments on the properties of superfluid helium in zero gravity

NASA Technical Reports Server (NTRS)

Mason, P.; Collins, D.; Petrac, D.; Yang, L.; Edeskuty, F.; Williamson, K.

1976-01-01

The paper describes a research program designed to study the behavior of superfluid liquid helium in low and zero gravity in order to determine the properties which are critically important to its use as a stored cryogen for cooling scientific instruments aboard spacecraft for periods up to several months. The experiment program consists of a series of flights of an experiment package on a free-fall trajectory both on an aircraft and on a rocket. The objectives are to study thickness of thin films of helium as a function of acceleration, heat transfer in thin films, heat transfer across copper-liquid helium interfaces, fluid dynamics of bulk helium in high and low accelerations and under various conditions of rotations, alternate methods of separation of liquid and vapor phases and of efficient venting of the vapor, and undesirable thermomechanical oscillations in the vent pipes. Preliminary results from aircraft tests are discussed.

Life characteristics assessment of the communications technology satellite transmitter experiment package

NASA Technical Reports Server (NTRS)

Smetana, J.; Curren, A. N.

1979-01-01

The performance characteristics of the transmitter experiment package (TEP) aboard the Communications Technology Satellite (CTS) measured during its first 2 years in orbit are presented. The TEP consists of a nominal 200 watt output stage tube (OST), a supporting power processing system (PPS), and a variable conductance heat pipe system (VCHPS). The OST, a traveling wave tube augmented with a 10 stage depressed collector has an overall saturated average efficiency of 51.5 percent and an average saturated radio frequency (rf) output power at center band frequency of 240 watts. The PPS operated with a measured efficiency of 86.5 to 88.5 percent. The VCHPS, using three pipes to conduct heat from the PPS and the OST to a 52 by 124 centimeter radiator fin, maintained the PPS baseplate temperature below 50 C for all operating conditions. The TEP performance characteristics presented include frequency response, rf output power, thermal performance, and efficiency. Communications characteristics were evaluated by using both video and audio modulated signals. On four occasions, the TEP experienced temporary thermal control system malfunctions. The anomalies were terminated safely, and the problem was investigated because of the potential for TEP damage due to the signficant temperature increases. Safe TEP operating procedures were established.

An assessment of the cloud signals simulated by NICAM using ISCCP, CALIPSO, and CloudSat satellite simulators

NASA Astrophysics Data System (ADS)

Kodama, C.; Noda, A. T.; Satoh, M.

2012-06-01

This study presents an assessment of three-dimensional structures of hydrometeors simulated by the NICAM, global nonhydrostatic atmospheric model without cumulus parameterization, using multiple satellite data sets. A satellite simulator package (COSP: the CFMIP Observation Simulator Package) is employed to consistently compare model output with ISCCP, CALIPSO, and CloudSat satellite observations. Special focus is placed on high thin clouds, which are not observable in the conventional ISCCP data set, but can be detected by the CALIPSO observations. For the control run, the NICAM simulation qualitatively captures the geographical distributions of the high, middle, and low clouds, even though the horizontal mesh spacing is as coarse as 14 km. The simulated low cloud is very close to that of the CALIPSO low cloud. Both the CloudSat observations and NICAM simulation show a boomerang-type pattern in the radar reflectivity-height histogram, suggesting that NICAM realistically simulates the deep cloud development process. A striking difference was found in the comparisons of high thin cirrus, showing overestimated cloud and higher cloud top in the model simulation. Several model sensitivity experiments are conducted with different cloud microphysical parameters to reduce the model-observation discrepancies in high thin cirrus. In addition, relationships among clouds, Hadley circulation, outgoing longwave radiation and precipitation are discussed through the sensitivity experiments.

Thermal anomalies of the transmitter experiment package on the communications technology satellite

NASA Technical Reports Server (NTRS)

Alexovich, R. E.; Curren, A. N.

1979-01-01

The causes of four temporary thermal-control-system malfunctions that gave rise to unexpected temperature excursions in the 12-gigahertz, 200-watt transmitter experiment package (TEP) on the Communications Technology Satellite were investigated. The TEP consists of a nominal 200-watt output stage tube (OST), a supporting power-processing system (PPS), and a variable-conductance heat-pipe system (VCHPS). The VCHPS, which uses three heat pipes to conduct heat from the body of the OST to a radiator fin, was designed to maintain the TEP at safe operating temperatures at all operating conditions. On four occasions during 1977, all near the spring and fall equinoxes, the OST body temperature and related temperatures displayed sudden, rapid, and unexpected rises above normal levels while the TEP was operating at essentially constant, normal conditions. The temperature excursions were terminated without TEP damage by reducing the radio frequency (RF) output power of the OST. Between the anomalies and since the fourth, the thermal control system has apparently functioned as designed. The results indicate the most probable cause of the temperature anomalies is depriming of the arteries in the variable-conductance heat pipes. A mode was identified in which the TEP, as presently configured, may operate with stable temperatures and with minimum change in performance level.

FIRST STATUS REPORT: TESTING OF AGED SOFTWOOD FIBERBOARD MATERIAL FOR THE 9975 SHIPPING PACKAGE

DOE Office of Scientific and Technical Information (OSTI.GOV)

Daugherty, W.

2010-01-08

Samples have been prepared from a softwood fiberboard lower subassembly. Physical, mechanical and thermal properties have been measured following varying periods of conditioning in each of several environments. These tests have been conducted in the same manner as previous testing on cane fiberboard samples. Overall, similar aging trends are observed for softwood and cane fiberboard samples. Some of the observed differences result from the limited exposure periods of the softwood fiberboard samples, and the impact of seasonal humidity levels. Testing following additional conditioning will continue and should eliminate this bias. Post-conditioning data have been measured on a single softwood fiberboardmore » assembly, and baseline data are also available from a limited number of vendor-provided samples. This provides minimal information on the possible sample-to-sample variation exhibited by softwood fiberboard. Data to date are generally consistent with the range seen in cane fiberboard, but much of the compression strength data tends toward the lower end of that range. Further understanding of the variability of softwood fiberboard properties will require testing of additional material. Cane fiberboard wall sheathing is specified for thermal insulation and impact resistance in 9975 shipping packages. Softwood fiberboard manufactured by Knight-Celotex was approved as an acceptable substitute for transportation in 2008. Data in the literature [1] show a consistent trend in thermal properties of fiberboard as a function of temperature, density and/or moisture content regardless of material source. Thermal and mechanical properties were measured for un-aged softwood fiberboard samples, and found to be sufficiently similar to those of un-aged cane fiberboard to support the acceptance of 9975 packages with softwood fiberboard overpack into KAMS for storage. The continued acceptability of aged softwood fiberboard to meet KAMS storage requirements was the subject of subsequent activities. This is an interim status report for experiments carried out per Task Technical Plan WSRC-TR-2008-00024 [2], which is part of the comprehensive 9975 package surveillance program [3]. The primary goal of this task is to validate the preliminary assessment that Knight-Celotex softwood fiberboard is an acceptable substitute for cane fiberboard in the 9975 shipping package overpack, and that the long-term performance of these two materials in a storage environment is comparable.« less

Event visualization in ATLAS

NASA Astrophysics Data System (ADS)

Bianchi, R. M.; Boudreau, J.; Konstantinidis, N.; Martyniuk, A. C.; Moyse, E.; Thomas, J.; Waugh, B. M.; Yallup, D. P.; ATLAS Collaboration

2017-10-01

At the beginning, HEP experiments made use of photographical images both to record and store experimental data and to illustrate their findings. Then the experiments evolved and needed to find ways to visualize their data. With the availability of computer graphics, software packages to display event data and the detector geometry started to be developed. Here, an overview of the usage of event display tools in HEP is presented. Then the case of the ATLAS experiment is considered in more detail and two widely used event display packages are presented, Atlantis and VP1, focusing on the software technologies they employ, as well as their strengths, differences and their usage in the experiment: from physics analysis to detector development, and from online monitoring to outreach and communication. Towards the end, the other ATLAS visualization tools will be briefly presented as well. Future development plans and improvements in the ATLAS event display packages will also be discussed.

Re-design of apple pia packaging using quality function deployment method

NASA Astrophysics Data System (ADS)

Pulungan, M. H.; Nadira, N.; Dewi, I. A.

2018-03-01

This study was aimed to identify the attributes for premium apple pia packaging, to determine the technical response to be carried out by Permata Agro Mandiri Small and Medium Enterprise (SME) and to design a new apple pie packaging acceptable by the SME. The Quality Function Deployment (QFD) method was employed to improve the apple pia packaging design, which consisted of seven stages in data analysis. The results indicated that whats attribute required by the costumers include graphic design, dimensions, capacity, shape, strength, and resistance of packaging. While, the technical responses to be conducted by the SMEs were as follows: attractive visual packaging designs, attractive colors, clear images and information, packaging size dimensions, a larger capacity packaging (more product content), ergonomic premium packaging, not easily torn, and impact resistant packaging materials. The findings further confirmed that the design of premium apple pia packaging accepted by the SMES was the one with the capacity of ten apple pia or 200 g weight, and with rectangular or beam shape form. The packaging material used was a duplex carton with 400 grammage (g/m2), the outer part of the packaging was coated with plastic and the inside was added with duplex carton. The acceptable packaging dimension was 30 cm x 5 cm x 3 cm (L x W x H) with a mix of black and yellow color in the graphical design.

Skylab S191 visible-infrared spectrometer. [in Earth Resources Experiment Package

NASA Technical Reports Server (NTRS)

Barnett, T. L.; Juday, R. D.

1977-01-01

The paper describes the S191 visible-infrared spectrometer of the Skylab Earth Resources Experiment Package - a manually pointed two-channel instrument operating in the reflective (0.4-2.5 micron) and thermal emissive (6-15 micron) regions. A sensor description is provided and attention is given to data quality in the short wavelength and thermal infrared regions.

NORAD LOOK ANGLES AND PIO SATELLITE PACKAGE

NASA Technical Reports Server (NTRS)

ANONYMOUS

1994-01-01

This program package consists of two programs. First is the NORAD Look Angles Program, which computes satellite look angles (azimuth, elevation, and range) as well as the subsatellite points (latitude, longitude, and height). The second program in this package is the PIO Satellite Program, which computes sighting directions, visibility times, and the maximum elevation angle attained during each pass of an earth-orbiting satellite. Computations take into consideration the observing location and the effect of the earth's shadow on the satellite visibility. Input consists of a magnetic tape prepared by the NORAD Look Angles Program and punched cards containing reference Julian date, right ascension, declination, mean sidereal time at zero hours universal time of the reference date, and daily changes of these quantities. Output consists of a tabulated listing of the satellite's rise and set times, direction, and the maximum elevation angle visible from each observing location. This program has been implemented on the GE 635. The program Assembler code can easily be replaced by FORTRAN statements.

Solar Water-Heater Design Package

NASA Technical Reports Server (NTRS)

1982-01-01

Information on a solar domestic-hot water heater is contained in 146 page design package. System consists of solar collector, storage tanks, automatic control circuitry and auxiliary heater. Data-acquisition equipment at sites monitors day-by-day performance. Includes performance specifications, schematics, solar-collector drawings and drawings of control parts.

78 FR 3898 - Agency Information Collection Activities: Submission for OMB Review; Comment Request

Federal Register 2010, 2011, 2012, 2013, 2014

2013-01-17

... service area. The plan benefit package submission consists of the Plan Benefit Package (PBP) software... DEPARTMENT OF HEALTH AND HUMAN SERVICES Centers for Medicare & Medicaid Services [Document...; Comment Request AGENCY: Centers for Medicare & Medicaid Services, HHS. In compliance with the requirement...

Image dissector control and data system, part 1. [instrument packages and equipment specifications

NASA Technical Reports Server (NTRS)

1974-01-01

A general description of the image dissector control and data system is presented along with detailed design information, operating instructions, and maintenance and trouble-shooting procedures for the four instrumentation packages. The four instrumentation packages include a 90 inch telescope, a simplified telescope module for use on the 90 inch or other telescopes, a photographic plate scanner module which permits the scanning of astronomical photographic plates in the laboratory, and the lunar experiment package module.

Analysis of microgravity space experiments Space Shuttle programmatic safety requirements

NASA Technical Reports Server (NTRS)

Terlep, Judith A.

1996-01-01

This report documents the results of an analysis of microgravity space experiments space shuttle programmatic safety requirements and recommends the creation of a Safety Compliance Data Package (SCDP) Template for both flight and ground processes. These templates detail the programmatic requirements necessary to produce a complete SCDP. The templates were developed from various NASA centers' requirement documents, previously written guidelines on safety data packages, and from personal experiences. The templates are included in the back as part of this report.

Engineering report on the OAO-2 Wisconsin experiment package

NASA Technical Reports Server (NTRS)

Bendell, C. B.

1972-01-01

The continued useful operation of the OAO-2 Wisconsin Experiment Package (WEP) for almost three years after its December 1968 launch is evidence of a superior engineering accomplishment. Reliability features of the experiment concept and design which have contributed to its long life are presented. Data anomalies and partial failures are summarized along with conclusions regarding their causes. The thermal, vacuum and radiation effects of the space environment are shown to be minimal and quite localized within the WEP.

Tests of a Semi-Analytical Case 1 and Gelbstoff Case 2 SeaWiFS Algorithm with a Global Data Set

NASA Technical Reports Server (NTRS)

Carder, Kendall L.; Hawes, Steve K.; Lee, Zhongping

1997-01-01

A semi-analytical algorithm was tested with a total of 733 points of either unpackaged or packaged-pigment data, with corresponding algorithm parameters for each data type. The 'unpackaged' type consisted of data sets that were generally consistent with the Case 1 CZCS algorithm and other well calibrated data sets. The 'packaged' type consisted of data sets apparently containing somewhat more packaged pigments, requiring modification of the absorption parameters of the model consistent with the CalCOFI study area. This resulted in two equally divided data sets. A more thorough scrutiny of these and other data sets using a semianalytical model requires improved knowledge of the phytoplankton and gelbstoff of the specific environment studied. Since the semi-analytical algorithm is dependent upon 4 spectral channels including the 412 nm channel, while most other algorithms are not, a means of testing data sets for consistency was sought. A numerical filter was developed to classify data sets into the above classes. The filter uses reflectance ratios, which can be determined from space. The sensitivity of such numerical filters to measurement resulting from atmospheric correction and sensor noise errors requires further study. The semi-analytical algorithm performed superbly on each of the data sets after classification, resulting in RMS1 errors of 0.107 and 0.121, respectively, for the unpackaged and packaged data-set classes, with little bias and slopes near 1.0. In combination, the RMS1 performance was 0.114. While these numbers appear rather sterling, one must bear in mind what mis-classification does to the results. Using an average or compromise parameterization on the modified global data set yielded an RMS1 error of 0.171, while using the unpackaged parameterization on the global evaluation data set yielded an RMS1 error of 0.284. So, without classification, the algorithm performs better globally using the average parameters than it does using the unpackaged parameters. Finally, the effects of even more extreme pigment packaging must be examined in order to improve algorithm performance at high latitudes. Note, however, that the North Sea and Mississippi River plume studies contributed data to the packaged and unpackaged classess, respectively, with little effect on algorithm performance. This suggests that gelbstoff-rich Case 2 waters do not seriously degrade performance of the semi-analytical algorithm.

Kinetic energy flux budget across air-sea interface

NASA Astrophysics Data System (ADS)

Fan, Yalin; Hwang, Paul

2017-12-01

The kinetic energy (KE) fluxes into subsurface currents (EFc) is an important boundary condition for ocean circulation models. Traditionally, numerical models assume the KE flux from wind (EFair) is identical to EFc, that is, no net KE is gained (or lost) by surface waves. This assumption, however, is invalid when the surface wave field is not fully developed, and acquires KE when it grows in space or time. In this study, numerical experiments are performed to investigate the KE flux budget across the air-sea interface under both uniform and idealized tropical cyclone (TC) winds. The wave fields are simulated using the WAVEWATCH III model under different wind forcing. The difference between EFair and EFc is estimated using an air-sea KE budget model. To address the uncertainty of these estimates resides in the variation of source functions, two source function packages are used for this study: the ST4 source package (Ardhuin et al, 2010), and the ST6 source package (Babanin, 2011). The modeled EFc is significantly reduced relative to EFair under growing seas for both the uniform and TC experiments. The reduction can be as large as 20%, and the variation of this ratio is highly dependent on the choice of source function for the wave model. Normalized EFc are found to be consistent with analytical expressions by Hwang and Sletten (2008) and Hwang and Walsh (2016) and field observations by Terray et al. (1996) and Drennan et al. (1996), while the scatters are more widely in the TC cases due to the complexity of the associated wave field. The waves may even give up KE to subsurface currents in the left rear quadrant of fast moving storms. Our results also suggest that the normalized KE fluxes may depend on both wave age and friction velocity (u*).

DarkBit: a GAMBIT module for computing dark matter observables and likelihoods

NASA Astrophysics Data System (ADS)

Bringmann, Torsten; Conrad, Jan; Cornell, Jonathan M.; Dal, Lars A.; Edsjö, Joakim; Farmer, Ben; Kahlhoefer, Felix; Kvellestad, Anders; Putze, Antje; Savage, Christopher; Scott, Pat; Weniger, Christoph; White, Martin; Wild, Sebastian

2017-12-01

We introduce DarkBit, an advanced software code for computing dark matter constraints on various extensions to the Standard Model of particle physics, comprising both new native code and interfaces to external packages. This release includes a dedicated signal yield calculator for gamma-ray observations, which significantly extends current tools by implementing a cascade-decay Monte Carlo, as well as a dedicated likelihood calculator for current and future experiments ( gamLike). This provides a general solution for studying complex particle physics models that predict dark matter annihilation to a multitude of final states. We also supply a direct detection package that models a large range of direct detection experiments ( DDCalc), and that provides the corresponding likelihoods for arbitrary combinations of spin-independent and spin-dependent scattering processes. Finally, we provide custom relic density routines along with interfaces to DarkSUSY, micrOMEGAs, and the neutrino telescope likelihood package nulike. DarkBit is written in the framework of the Global And Modular Beyond the Standard Model Inference Tool ( GAMBIT), providing seamless integration into a comprehensive statistical fitting framework that allows users to explore new models with both particle and astrophysics constraints, and a consistent treatment of systematic uncertainties. In this paper we describe its main functionality, provide a guide to getting started quickly, and show illustrative examples for results obtained with DarkBit (both as a stand-alone tool and as a GAMBIT module). This includes a quantitative comparison between two of the main dark matter codes ( DarkSUSY and micrOMEGAs), and application of DarkBit 's advanced direct and indirect detection routines to a simple effective dark matter model.

Community-based benchmarking of the CMIP DECK experiments

NASA Astrophysics Data System (ADS)

Gleckler, P. J.

2015-12-01

A diversity of community-based efforts are independently developing "diagnostic packages" with little or no coordination between them. A short list of examples include NCAR's Climate Variability Diagnostics Package (CVDP), ORNL's International Land Model Benchmarking (ILAMB), LBNL's Toolkit for Extreme Climate Analysis (TECA), PCMDI's Metrics Package (PMP), the EU EMBRACE ESMValTool, the WGNE MJO diagnostics package, and CFMIP diagnostics. The full value of these efforts cannot be realized without some coordination. As a first step, a WCRP effort has initiated a catalog to document candidate packages that could potentially be applied in a "repeat-use" fashion to all simulations contributed to the CMIP DECK (Diagnostic, Evaluation and Characterization of Klima) experiments. Some coordination of community-based diagnostics has the additional potential to improve how CMIP modeling groups analyze their simulations during model-development. The fact that most modeling groups now maintain a "CMIP compliant" data stream means that in principal without much effort they could readily adopt a set of well organized diagnostic capabilities specifically designed to operate on CMIP DECK experiments. Ultimately, a detailed listing of and access to analysis codes that are demonstrated to work "out of the box" with CMIP data could enable model developers (and others) to select those codes they wish to implement in-house, potentially enabling more systematic evaluation during the model development process.

COLDMON -- Cold File Analysis Package

NASA Astrophysics Data System (ADS)

Rawlinson, D. J.

The COLDMON package has been written to allow system managers to identify those items of software that are not used (or used infrequently) on their systems. It consists of a few command procedures and a Fortran program to analyze the results. It makes use of the AUDIT facility and security ACLs in VMS.

Effects of Fluency Instruction on Selection-Based and Topography-Based Comprehension Measures

ERIC Educational Resources Information Center

Barnes, Clarissa S.; Rehfeldt, Ruth Anne

2013-01-01

A multiple probe across participants design was used to assess the effects of an intervention package on reading fluency and section-based and topography-based comprehension tasks. Participants were three adolescents diagnosed with high functioning pervasive developmental disorders. The intervention package consisted of listen passage preview,…

The Blue Tube.

ERIC Educational Resources Information Center

Wallisch, Bill; Taylor, Bob

The "Blue Tube" is a 2-part academic package developed at the U.S. Air Force Academy consisting of an English course in communication and writing skills and a management course in advertising and marketing; the two courses are interrelated through student assignments in television production. The first part of the package includes…

Installation package for Hyde Memorial Observatory, Lincoln, Nebraska

NASA Technical Reports Server (NTRS)

1978-01-01

Installation information for a solar heating system installed in Hyde Memorial Observatory at Lincoln, Nebraska is presented. This package included a system operation and maintenance manual, hardware brochures, schematics, system operating modes, and drawings. This prototype solar heating system consisted of the following subsystems: solar collector, control, and storage.

Cleanup Verification Package for the 100-F-20, Pacific Northwest Laboratory Parallel Pits

DOE Office of Scientific and Technical Information (OSTI.GOV)

M. J. Appel

2007-01-22

This cleanup verification package documents completion of remedial action for the 100-F-20, Pacific Northwest Laboratory Parallel Pits waste site. This waste site consisted of two earthen trenches thought to have received both radioactive and nonradioactive material related to the 100-F Experimental Animal Farm.

THE USE OF COMPUTER MODELING PACKAGES TO ILLUSTRATE UNCERTAINTY IN RISK ASSESSMENTS: AN EASE OF USE AND INTERPRETATION COMPARISON

EPA Science Inventory

Consistent improvements in processor speed and computer access have substantially increased the use of computer modeling by experts and non-experts alike. Several new computer modeling packages operating under graphical operating systems (i.e. Microsoft Windows or Macintosh) m...

Shock-isolation material selection for electronic packages in hard-target environment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stotts, Jarrett Eugene

High velocity munitions and kinetic penetrators experience monumental external forces, impulses, and accelerations. The hard target environment is immensely taxing on sophisticated electronic components and recorders designed to retrieve valuable data related to the systems performance and characteristics in the periods of flight, impact, and post-impact. Such electronic systems have upper limits of overall shock intensity which, if exceeded, will either shorten the operating life of the parts or risk destruction resulting in loss of both the data and the principal value of the recorder. The focus of this project was to refine the categorization of leading material types formore » encapsulation and passive shock isolation and implement them in a method useable for a wide variety of environments. Namely, a design methodology capable of being tailored to the specific impact conditions to maximize the lively hood of sensitive electronics and the information recorded. The results of the study concluded that the materials observed under consistent dynamic high strain rate tests, which include Conathane® EN-4/9, Slygard®-184, and Stycast™-2651, behaved well in certain aspects of energy transmission and shock when considering the frequency environment or package coupled with the isolation material’s application. Key points about the implementation of the materials in extreme shock environments is discussed with the connection to energy analysis, loss attributes, and pulse transmissibility modeling. However, attempts to model the materials solely based on energy transmissibility in the frequency domain using only external experimental data and simplified boundary conditions was not found to be consistent with that acquired from the pressure bar experiments. Further work will include the addition of further material experimentation of the encapsulants in other frequency and temperature states, confined and pre-load boundary states, and composite constructions.« less

Model 9975 Life Extension Test Package 3 - Interim Report - January 2017

DOE Office of Scientific and Technical Information (OSTI.GOV)

Daugherty, W.

2017-01-31

Life extension package LE3 (9975-03203) has been instrumented and subjected to an elevated temperature environment for approximately 8 years. During this time, the cane fiberboard has been maintained at a maximum temperature of ~160 - 165 °F, which was established by a combination of internal (19 watts) and external heat sources. Several tests and parameters were used to characterize the package components. Results from these tests generally indicate agreement between this full-scale shipping package and small-scale laboratory tests on fiberboard samples, including the degradation models based on the laboratory tests. These areas of agreement include the rate of change ofmore » fiberboard weight, dimensions and density, and change in fiberboard thermal conductivity. Corrosion of the lead shield occurred at a high rate during the first several weeks of aging, but dropped significantly after most of the moisture in the fiberboard migrated away from the lead shield. Dimensional measurements of the lead shield indicate that no significant creep deformation has occurred. This is consistent with literature data that predict a very small creep deformation for the time at temperature experienced by this package. The SCV O-rings were verified to remain leak-tight after ~5 years aging at an average temperature of ~170 °F. This package provides an example of the extent to which moisture within a typical fiberboard assembly can redistribute in the presence of a temperature gradient such as might be created by a 19 watt internal heat load. The majority of water within the fiberboard migrated to the bottom layers of fiberboard, with approximately 2 kg of water (2 liters) eventually escaping from the package. Two conditions have developed that are not consistent with package certification requirements. The axial gap at the top of the package increased to a maximum value of 1.549 inches, exceeding the 1 inch criterion. In addition, staining and/or corrosion have formed in a few spots on the drum. However, the package remains capable of performing its function. Aging of this package continues.« less

WEB - A Wireless Experiment Box for the Dextre Pointing Package ELC Payload

NASA Technical Reports Server (NTRS)

Bleier, Leor Z.; Marrero-Fontanez, Victor J.; Sparacino, Pietro A.; Moreau, Michael C.; Mitchell, Jason William

2012-01-01

The Wireless Experiment Box (WEB) was proposed to work with the International Space Station (ISS) External Wireless Communication (EWC) system to support high-definition video from the Dextre Pointing Package (DPP). DPP/WEB was a NASA GSFC proposed ExPRESS Logistics Carrier (ELC) payload designed to flight test an integrated suite of Autonomous Rendezvous and Docking (AR&D) technologies to enable a wide spectrum of future missions across NASA and other US Government agencies. The ISS EWC uses COTS Wireless Access Points (WAPs) to provide high-rate bi-directional communications to ISS. In this paper, we discuss WEB s packaging, operation, antenna development, and performance testing.

Web: A Wireless Experiment Box for the Dextre Pointing Package ELC Payload

NASA Technical Reports Server (NTRS)

Bleier, Leor Z.; Marrero-Fontanez, Victor J.; Sparacino, Pietro A.; Moreau, Michael C.; Mitchell, Jason W.

2012-01-01

The Wireless Experiment Box (WEB) was proposed to work with the International Space Station (ISS) External Wireless Communication (EWC) system to support high-definition video from the Dextre Pointing Package (DPP). DPP/WEB was a NASA GSFC proposed ExPRESS Logistics Carrier (ELC) payload designed to flight test an integrated suite of Autonomous Rendezvous and Docking (AR&D) technologies to enable a wide spectrum of future missions across NASA and other US Government agencies. The ISS EWC uses COTS Wireless Access Points (WAPs) to provide high-rate bi-directional communications to ISS. In this paper, we discuss WEB s packaging, operation, antenna development, and performance testing.

The 9th international symposium on the packaging and transportation of radioactive materials

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

1989-06-01

This three-volume document contains the papers and poster sessions presented at the symposium. Volume 3 contains 87 papers on topics such as structural codes and benchmarking, shipment of plutonium by air, spent fuel shipping, planning, package design and risk assessment, package testing, OCRWN operations experience and regulations. Individual papers were processed separately for the data base. (TEM)

Dynamic Control System Mode Performance of the Space Technology-7 Disturbance Reduction System

NASA Technical Reports Server (NTRS)

O'Donnell, James R., Jr.; Hsu, Oscar; Maghami, Peiman

2017-01-01

The Space Technology-7 (ST-7) Disturbance Reduction System (DRS) is an experiment package aboard the European Space Agency (ESA) LISA Pathfinder spacecraft, launched on December 3, 2015. DRS consists of three primary components: Colloidal MicroNewton Thrusters (CMNTs), an Integrated Avionics Unit (IAU), and flight-software implementing the Command and Data Handling (C&DH) and Dynamic Control System (DCS) algorithms. The CMNTs were designed to provide thrust from 5 to 30 micro Newton, with thrust controllability and resolution of 0.1 micro Newton and thrust noise of 0.1 micro Newton/(square root of (Hz)) in the measurement band from 1-30 mHz. The IAU hosts the C&DH and DCS flight software, as well as interfaces with both the CMNT electronics and the LISA Pathfinder spacecraft. When in control, the DCS uses star tracker attitude data and capacitive or optically-measured position and attitude information from LISA Pathfinder and the LISA Technology Package (LTP) to control the attitude and position of the spacecraft and the two test masses inside the LTP. After completion of the nominal ESA LISA Pathfinder mission, the DRS experiment was commissioned followed by its nominal mission. DRS operations extended over the next five months, interspersed with station keeping, anomaly resolution, and periods where control was handed back to LISA Pathfinder for them to conduct further experiments. The primary DRS mission ended on December 6, 2016, with the experiment meeting all of its Level 1 requirements. The DCS, developed at the NASA Goddard Space Flight Center, consists of five spacecraft control modes and six test mass control modes, combined into six 'DRS Mission Modes'. Attitude Control and Zero-G were primarily used to control the spacecraft during initial handover and during many of the CMNT characterization experiments. The other Mission Modes, Drag Free Low Force, 18-DOF Transitional, and 18-DOF, were used to provide drag-free control of the spacecraft about the test masses. This paper will discuss the performance of these DCS spacecraft and test mass control modes. Flight data will be shown from each mode throughout the mission, both from nominal operations and during various flight experiments. The DCS team also made some changes to controller, filter, and limit parameters during operations; the motivation and results of these changes will be shown and discussed.

When is an image a health claim? A false-recollection method to detect implicit inferences about products' health benefits.

PubMed

Klepacz, Naomi A; Nash, Robert A; Egan, M Bernadette; Hodgkins, Charo E; Raats, Monique M

2016-08-01

Images on food and dietary supplement packaging might lead people to infer (appropriately or inappropriately) certain health benefits of those products. Research on this issue largely involves direct questions, which could (a) elicit inferences that would not be made unprompted, and (b) fail to capture inferences made implicitly. Using a novel memory-based method, in the present research, we explored whether packaging imagery elicits health inferences without prompting, and the extent to which these inferences are made implicitly. In 3 experiments, participants saw fictional product packages accompanied by written claims. Some packages contained an image that implied a health-related function (e.g., a brain), and some contained no image. Participants studied these packages and claims, and subsequently their memory for seen and unseen claims were tested. When a health image was featured on a package, participants often subsequently recognized health claims that-despite being implied by the image-were not truly presented. In Experiment 2, these recognition errors persisted despite an explicit warning against treating the images as informative. In Experiment 3, these findings were replicated in a large consumer sample from 5 European countries, and with a cued-recall test. These findings confirm that images can act as health claims, by leading people to infer health benefits without prompting. These inferences appear often to be implicit, and could therefore be highly pervasive. The data underscore the importance of regulating imagery on product packaging; memory-based methods represent innovative ways to measure how leading (or misleading) specific images can be. (PsycINFO Database Record (c) 2016 APA, all rights reserved).

How Strong Is Your Coffee? The Influence of Visual Metaphors and Textual Claims on Consumers’ Flavor Perception and Product Evaluation

PubMed Central

Fenko, Anna; de Vries, Roxan; van Rompay, Thomas

2018-01-01

This study investigates the relative impact of textual claims and visual metaphors displayed on the product’s package on consumers’ flavor experience and product evaluation. For consumers, strength is one of the most important sensory attributes of coffee. The 2 × 3 between-subjects experiment (N = 123) compared the effects of visual metaphor of strength (an image of a lion located either on top or on the bottom of the package of coffee beans) and the direct textual claim (“extra strong”) on consumers’ responses to coffee, including product expectation, flavor evaluation, strength perception and purchase intention. The results demonstrate that both the textual claim and the visual metaphor can be efficient in communicating the product attribute of strength. The presence of the image positively influenced consumers’ product expectations before tasting. The textual claim increased the perception of strength of coffee and the purchase intention of the product. The location of the image also played an important role in flavor perception and purchase intention. The image located on the bottom of the package increased the perceived strength of coffee and purchase intention of the product compared to the image on top of the package. This result could be interpreted from the perspective of the grounded cognition theory, which suggests that a picture in the lower part of the package would automatically activate the “strong is heavy” metaphor. As heavy objects are usually associated with a position on the ground, this would explain why perceiving a visually heavy package would lead to the experience of a strong coffee. Further research is needed to better understand the relationships between a metaphorical image and its spatial position in food packaging design. PMID:29459840

smwrData—An R package of example hydrologic data, version 1.1.1

USGS Publications Warehouse

Lorenz, David L.

2015-11-06

A collection of 24 datasets, including streamflow, well characteristics, groundwater elevations, and discrete water-quality concentrations, is provided to produce a consistent set of example data to demonstrate typical data manipulations or statistical analysis of hydrologic data. These example data are provided in an R package called smwrData. The data in the package have been collected by the U.S. Geological Survey or published in its reports, for example Helsel and Hirsch (2002). The R package provides a convenient mechanism for distributing the data to users of R within the U.S. Geological Survey and other users in the R community.

Compact, Engineered 2-Micron Coherent Doppler Wind Lidar Prototype for Field and Airborne Evaluation

NASA Technical Reports Server (NTRS)

Kavaya, Michael J.; Amzajerdian, Farzin; Koch, Grady J.

2006-01-01

The state-of-the-art 2-micron coherent Doppler wind lidar breadboard at NASA/LaRC will be engineered and compactly packaged consistent with future aircraft flights. The packaged transceiver will be integrated into a coherent Doppler wind lidar system test bed at LaRC. Atmospheric wind measurements will be made to validate the packaged technology. This will greatly advance the coherent part of the hybrid Doppler wind lidar solution to the need for global tropospheric wind measurements.

A User-Friendly Software Package for HIFU Simulation

NASA Astrophysics Data System (ADS)

Soneson, Joshua E.

2009-04-01

A freely-distributed, MATLAB (The Mathworks, Inc., Natick, MA)-based software package for simulating axisymmetric high-intensity focused ultrasound (HIFU) beams and their heating effects is discussed. The package (HIFU_Simulator) consists of a propagation module which solves the Khokhlov-Zabolotskaya-Kuznetsov (KZK) equation and a heating module which solves Pennes' bioheat transfer (BHT) equation. The pressure, intensity, heating rate, temperature, and thermal dose fields are computed, plotted, the output is released to the MATLAB workspace for further user analysis or postprocessing.

Eddylicious: A Python package for turbulent inflow generation

NASA Astrophysics Data System (ADS)

Mukha, Timofey; Liefvendahl, Mattias

2018-01-01

A Python package for generating inflow for scale-resolving computer simulations of turbulent flow is presented. The purpose of the package is to unite existing inflow generation methods in a single code-base and make them accessible to users of various Computational Fluid Dynamics (CFD) solvers. The currently existing functionality consists of an accurate inflow generation method suitable for flows with a turbulent boundary layer inflow and input/output routines for coupling with the open-source CFD solver OpenFOAM.

smwrBase—An R package for managing hydrologic data, version 1.1.1

USGS Publications Warehouse

Lorenz, David L.

2015-12-09

This report describes an R package called smwrBase, which consists of a collection of functions to import, transform, manipulate, and manage hydrologic data within the R statistical environment. Functions in the package allow users to import surface-water and groundwater data from the U.S. Geological Survey’s National Water Information System database and other sources. Additional functions are provided to transform, manipulate, and manage hydrologic data in ways necessary for analyzing the data.

Halley's Comet and Beyond.

ERIC Educational Resources Information Center

Sneider, Cary; DeVore, Edna

1986-01-01

Reviews software packages under these headings: (1) simulations of experiments; (2) space flight simulators; (3) planetariums; (4) space adventure games; and (5) drill and practice packages (designed for testing purposes or for helping students learn basic astronomy vocabulary). (JN)

Which Air Force Civil Engineer Capabilities Can Complement USNORTHCOM’s Role in Defense Support to Civil Authorities (DSCA)?

DTIC Science & Technology

2014-05-21

UTC REQUIRES PERSONNEL FROM STANDARD PRIME BEEF OR RED 4F9K4 PROVIDES FOLDED FIBERGLASS MATTING ( FFM ) FOR AIRFIELD DAMAGE REPAIR (ADR). PACKAGE...CONSISTS OF THREE FFM SETS (54’ X 60’), ONE FFM SUPPORT TOOL KIT, UPPER BUSHINGS, ANCHOR BUSHINGS, ANCHOR BOLTS, AND TWO EA MC-7 AIR COMPRESSORS. EACH...PACKAGE CONSISTS OF 7 FOLDED FIBERGLASS MAT SETS (54 FT X 60 FT), 2 FFM SUPPORT TOOL KIT, UPPER BUSHINGS, ANCHOR BUSHINGS, ANCHOR BOLTS AND 4 X

Cloud-Coffee: implementation of a parallel consistency-based multiple alignment algorithm in the T-Coffee package and its benchmarking on the Amazon Elastic-Cloud.

PubMed

Di Tommaso, Paolo; Orobitg, Miquel; Guirado, Fernando; Cores, Fernado; Espinosa, Toni; Notredame, Cedric

2010-08-01

We present the first parallel implementation of the T-Coffee consistency-based multiple aligner. We benchmark it on the Amazon Elastic Cloud (EC2) and show that the parallelization procedure is reasonably effective. We also conclude that for a web server with moderate usage (10K hits/month) the cloud provides a cost-effective alternative to in-house deployment. T-Coffee is a freeware open source package available from http://www.tcoffee.org/homepage.html

75 FR 27273 - Hazardous Materials; Packages Intended for Transport by Aircraft

Federal Register 2010, 2011, 2012, 2013, 2014

2010-05-14

...PHMSA proposes to amend requirements in the Hazardous Materials Regulations to enhance the integrity of inner packagings or receptacles of combination packagings containing liquid hazardous material by ensuring they remain intact when subjected to the reduced pressure and other forces encountered in air transportation. In order to substantially decrease the likelihood of a hazardous materials release, the proposed amendments: prescribe specific test protocols and standards for determining whether an inner packaging or receptacle is capable of meeting the pressure differential requirements specified in the regulations and, consistent with the 2011-2012 edition of the International Civil Aviation Organization Technical Instructions for the Safe Transport of Dangerous Goods by Aircraft (ICAO Technical Instructions), require the closures on all inner packagings containing liquids within a combination packaging to be secured by a secondary means or, under certain circumstances, permit the use of a liner.

Investigation of low cost, high reliability sealing techniques for hybrid microcircuits, phase 1

NASA Technical Reports Server (NTRS)

Perkins, K. L.; Licari, J. J.

1976-01-01

A preliminary investigation was made to determine the feasibility of using adhesive package sealing for hybrid microcircuits. Major effort consisted of: (1) surveying representative hybrid manufacturers to assess the current use of adhesives for package sealing; (2) making a cost comparison of metallurgical versus adhesive package sealing; (3) determining the seal integrity of gold plated flatpack type packages sealed with selected adhesives, thermal shock, temperature cycling, mechanical shock, and constant acceleration test environments; and (4) defining a more comprehensive study to continue the evaluation of adhesives for package sealing. Results showed that 1.27 cm square gold plated flatpack type packages sealed with the film adhesives and the paste adhesive retained their seal integrity after all tests, and that similarly prepared 2.54 cm square packages retained their seal integrity after all tests except the 10,000 g's constant acceleration test. It is concluded that these results are encouraging, but by no means sufficient to establish the suitability of adhesives for sealing high reliability hybrid microcircuits.

Feasibility of biodegradable based packaging used for red meat storage during shelf-life: A pilot study.

PubMed

Panseri, S; Martino, P A; Cagnardi, P; Celano, G; Tedesco, D; Castrica, M; Balzaretti, C; Chiesa, L M

2018-05-30

This study was designated to ascertain the effectiveness of polylactic acid (PLA) based packaging solution to store red fresh meat during its refrigerated shelf-life. Recently the attention in the packaging industry regarding the use of bioplastics has been shifting from compostable/biodegradable materials toward biobased materials. Steaks obtained from semimembranous muscle of Piemontese beef were packaged in PLA trays closed with a lid made of PLA film and for comparison purposed in a conventional reference package consisting of a amorphous polyethylene terephthalate/polyethylene (APET/PET) trays and wrapped in plastic film of polyvinyl chloride (PVC). The packaging under modified atmosphere MAP was carried out by using a gas mixture of 66% O 2 , 25% CO 2 and 9%N 2 . By using PLA packaging combination it was possible to maintain an optimum red colour together with a reduced content of volatile compounds associated to off-flavours of meat samples particularly related to the oxidation phenomena. Copyright © 2017 Elsevier Ltd. All rights reserved.

ATACseqQC: a Bioconductor package for post-alignment quality assessment of ATAC-seq data.

PubMed

Ou, Jianhong; Liu, Haibo; Yu, Jun; Kelliher, Michelle A; Castilla, Lucio H; Lawson, Nathan D; Zhu, Lihua Julie

2018-03-01

ATAC-seq (Assays for Transposase-Accessible Chromatin using sequencing) is a recently developed technique for genome-wide analysis of chromatin accessibility. Compared to earlier methods for assaying chromatin accessibility, ATAC-seq is faster and easier to perform, does not require cross-linking, has higher signal to noise ratio, and can be performed on small cell numbers. However, to ensure a successful ATAC-seq experiment, step-by-step quality assurance processes, including both wet lab quality control and in silico quality assessment, are essential. While several tools have been developed or adopted for assessing read quality, identifying nucleosome occupancy and accessible regions from ATAC-seq data, none of the tools provide a comprehensive set of functionalities for preprocessing and quality assessment of aligned ATAC-seq datasets. We have developed a Bioconductor package, ATACseqQC, for easily generating various diagnostic plots to help researchers quickly assess the quality of their ATAC-seq data. In addition, this package contains functions to preprocess aligned ATAC-seq data for subsequent peak calling. Here we demonstrate the utilities of our package using 25 publicly available ATAC-seq datasets from four studies. We also provide guidelines on what the diagnostic plots should look like for an ideal ATAC-seq dataset. This software package has been used successfully for preprocessing and assessing several in-house and public ATAC-seq datasets. Diagnostic plots generated by this package will facilitate the quality assessment of ATAC-seq data, and help researchers to evaluate their own ATAC-seq experiments as well as select high-quality ATAC-seq datasets from public repositories such as GEO to avoid generating hypotheses or drawing conclusions from low-quality ATAC-seq experiments. The software, source code, and documentation are freely available as a Bioconductor package at https://bioconductor.org/packages/release/bioc/html/ATACseqQC.html .

Long term dose monitoring onboard the European Columbus module of the international space station (ISS) in the frame of DOSIS and DOSIS 3D project - results from the active instruments

NASA Astrophysics Data System (ADS)

Burmeister, Soenke; Berger, Thomas; Reitz, Guenther; Boehme, Matthias; Haumann, Lutz; Labrenz, Johannes

Besides the effects of the microgravity environment, and the psychological and psychosocial problems encountered in confined spaces, radiation is the main health detriment for long duration human space missions. The radiation environment encountered in space differs in nature from that on earth, consisting mostly of high energetic ions from protons up to iron, resulting in radiation levels far exceeding the ones encountered on earth for occupational radiation workers. Accurate knowledge of the physical characteristics of the space radiation field in dependence on the solar activity, the orbital parameters and the different shielding configurations of the International Space Station ISS is therefore needed. For the investigation of the spatial and temporal distribution of the radiation field inside the European COLUMBUS module the experiment DOSIS (Dose Distribution Inside the ISS) under the lead of DLR has been launched on July 15 (th) 2009 with STS-127 to the ISS. The experimental package was transferred from the Space Shuttle into COLUMBUS on July 18 (th) . It consists of a combination of passive detector packages (PDP) distributed at 11 locations inside the European Columbus Laboratory and two active radiation detectors (Dosimetry Telescopes = DOSTELs) with a DDPU (DOSTEL Data and Power Unit) in a Nomex pouch (DOSIS MAIN BOX) mounted at a fixed location beneath the European Physiology Module rack (EPM) inside COLUMBUS. The active components of the DOSIS experiment were operational from July 18 (th) 2009 to June 16 (th) 2011. After refurbishment the hardware has been reactivated on May 15 (th) 2012 as active part of the DOSIS 3D experiment and provides continuous data since this activation. The presentation will focus on the latest results from the two DOSTEL instruments as absorbed dose, dose equivalent and the related LET spectra gathered within the DOSIS (2009 - 2011) and DOSIS 3D (2012 - 2014) experiment. The CAU contributions to DOSIS and DOSIS 3D are financially supported by BMWi under Grants 50WB0826, 50WB1026 and 50WB1232

Restoration and Reexamination of Data from the Apollo 11, 12, 14, and 15 Dust, Thermal and Radiation Engineering Measurements Experiments

NASA Technical Reports Server (NTRS)

McBride, Marie J.; Williams, David R.; Kent, H.; Turner, Niescja

2012-01-01

As part of an effort by the Lunar Data Node (LDN) we are restoring data returned by the Apollo Dust, Thermal, and Radiation Engineering Measurements (DTREM) packages emplaced on the lunar surface by the crews of Apollo 11, 12, 14, and 15. Also commonly known as the Dust Detector experiments, the DTREM packages measured the outputs of exposed solar cells and thermistors over time. They operated on the surface for up to nearly 8 years, returning data every 54 seconds. The Apollo 11 DTREM was part of the Early Apollo Surface Experiments Package (EASEP), and operated for a few months as planned following emplacement in July 1969. The Apollo 12, 14, and 15 DTREMs were mounted on the central station as part of the Apollo Lunar Surface Experiments Package (ALSEP) and operated from deployment until ALSEP shutdown in September 1977. The objective of the DTREM experiments was to determine the effects of lunar and meteoric dust, thermal stresses, and radiation exposure on solar cells. The LDN, part of the Geosciences Node of the Planetary Data System (PDS), operates out of the National Space Science Data Center (NSSDC) at Goddard Space Flight Center. The goal of the LDN is to extract lunar data stored on older media and/or in obsolete formats, restore the data into a usable digital format, and archive the data with PDS and NSSDC. For the DTREM data we plan to recover the raw telemetry, translate the raw counts into appropriate output units, and then apply calibrations. The final archived data will include the raw, translated, and calibrated data and the associated conversion tables produced from the microfilm, as well as ancillary supporting data (metadata) packaged in PDS format.

High coherence plane breaking packaging for superconducting qubits.

PubMed

Bronn, Nicholas T; Adiga, Vivekananda P; Olivadese, Salvatore B; Wu, Xian; Chow, Jerry M; Pappas, David P

2018-04-01

We demonstrate a pogo pin package for a superconducting quantum processor specifically designed with a nontrivial layout topology (e.g., a center qubit that cannot be accessed from the sides of the chip). Two experiments on two nominally identical superconducting quantum processors in pogo packages, which use commercially available parts and require modest machining tolerances, are performed at low temperature (10 mK) in a dilution refrigerator and both found to behave comparably to processors in standard planar packages with wirebonds where control and readout signals come in from the edges. Single- and two-qubit gate errors are also characterized via randomized benchmarking, exhibiting similar error rates as in standard packages, opening the possibility of integrating pogo pin packaging with extensible qubit architectures.

High coherence plane breaking packaging for superconducting qubits

NASA Astrophysics Data System (ADS)

Bronn, Nicholas T.; Adiga, Vivekananda P.; Olivadese, Salvatore B.; Wu, Xian; Chow, Jerry M.; Pappas, David P.

2018-04-01

We demonstrate a pogo pin package for a superconducting quantum processor specifically designed with a nontrivial layout topology (e.g., a center qubit that cannot be accessed from the sides of the chip). Two experiments on two nominally identical superconducting quantum processors in pogo packages, which use commercially available parts and require modest machining tolerances, are performed at low temperature (10 mK) in a dilution refrigerator and both found to behave comparably to processors in standard planar packages with wirebonds where control and readout signals come in from the edges. Single- and two-qubit gate errors are also characterized via randomized benchmarking, exhibiting similar error rates as in standard packages, opening the possibility of integrating pogo pin packaging with extensible qubit architectures.

RNA secondary structures of the bacteriophage phi6 packaging regions.

PubMed

Pirttimaa, M J; Bamford, D H

2000-06-01

Bacteriophage phi6 genome consists of three segments of double-stranded RNA. During maturation, single-stranded copies of these segments are packaged into preformed polymerase complex particles. Only phi6 RNA is packaged, and each particle contains only one copy of each segment. An in vitro packaging and replication assay has been developed for phi6, and the packaging signals (pac sites) have been mapped to the 5' ends of the RNA segments. In this study, we propose secondary structure models for the pac sites of phi6 single-stranded RNA segments. Our models accommodate data from structure-specific chemical modifications, free energy minimizations, and phylogenetic comparisons. Previously reported pac site deletion studies are also discussed. Each pac site possesses a unique architecture, that, however, contains common structural elements.

Documentation for the MODFLOW 6 Groundwater Flow Model

USGS Publications Warehouse

Langevin, Christian D.; Hughes, Joseph D.; Banta, Edward R.; Niswonger, Richard G.; Panday, Sorab; Provost, Alden M.

2017-08-10

This report documents the Groundwater Flow (GWF) Model for a new version of MODFLOW called MODFLOW 6. The GWF Model for MODFLOW 6 is based on a generalized control-volume finite-difference approach in which a cell can be hydraulically connected to any number of surrounding cells. Users can define the model grid using one of three discretization packages, including (1) a structured discretization package for defining regular MODFLOW grids consisting of layers, rows, and columns, (2) a discretization by ver­tices package for defining layered unstructured grids consisting of layers and cells, and (3) a general unstruc­tured discretization package for defining flexible grids comprised of cells and their connection properties. For layered grids, a new capability is available for removing thin cells and vertically connecting cells overlying and underlying the thin cells. For complex problems involving water-table conditions, an optional Newton-Raphson formulation, based on the formulations in MODFLOW-NWT and MODFLOW-USG, can be acti­vated. Use of the Newton-Raphson formulation will often improve model convergence and allow solutions to be obtained for difficult problems that cannot be solved using the traditional wetting and drying approach. The GWF Model is divided into “packages,” as was done in previous MODFLOW versions. A package is the part of the model that deals with a single aspect of simulation. Packages included with the GWF Model include those related to internal calculations of groundwater flow (discretization, initial conditions, hydraulic conduc­tance, and storage), stress packages (constant heads, wells, recharge, rivers, general head boundaries, drains, and evapotranspiration), and advanced stress packages (streamflow routing, lakes, multi-aquifer wells, and unsaturated zone flow). An additional package is also available for moving water available in one package into the individual features of the advanced stress packages. The GWF Model also has packages for obtaining and controlling output from the model. This report includes detailed explanations of physical and mathematical concepts on which the GWF Model and its packages are based.Like its predecessors, MODFLOW 6 is based on a highly modular structure; however, this structure has been extended into an object-oriented framework. The framework includes a robust and generalized numeri­cal solution object, which can be used to solve many different types of models. The numerical solution object has several different matrix preconditioning options as well as several methods for solving the linear system of equations. In this new framework, the GWF Model itself is an object as are each of the GWF Model packages. A benefit of the object-oriented structure is that multiple objects of the same type can be used in a single sim­ulation. Thus, a single forward run with MODFLOW 6 may contain multiple GWF Models. GWF Models can be hydraulically connected using GWF-GWF Exchange objects. Connecting GWF models in different ways permits the user to utilize a local grid refinement strategy consisting of parent and child models or to couple adjacent GWF Models. An advantage of the approach implemented in MODFLOW 6 is that multiple models and their exchanges can be incorporated into a single numerical solution object. With this design, models can be tightly coupled at the matrix level.

Development of tube-packaged FBG strain sensor and application in the vibration experiment of submarine pipeline model

NASA Astrophysics Data System (ADS)

Ren, Liang; Li, Hong-Nan; Sun, Li; Li, Dong-Sheng

2005-05-01

Optical fiber sensors have received increasing attention in the fields of aeronautic and civil engineering for their superior ability of explosion proof, immunity to electromagnetic interference and high accuracy, especially fitting for measurement applications in harsh environment. In this paper, a novel FBG (fiber Bragg grating) strain sensor, which was packaged in a 1.2mm stainless steel tube by epoxy resin, was developed. Experiments were conducted on the universal material testing machine to calibrate its strain transferring characteristics. The sensor has the advantages of small size, high precision and flexible use, and demonstrates promising potentials. Ten of tube-packaged strain FBG sensors were applied in the vibration experiment of submarine pipeline model. The strain measured by FBG sensor agrees well with the electric resistance strain sensor.

Development of tube-packaged FBG strain sensor and application in the vibration experiment of submarine pipeline model

NASA Astrophysics Data System (ADS)

Ren, Liang; Li, Hong-Nan; Sun, Li; Li, Dong-Sheng

2005-02-01

Optical fiber sensors have received increasing attention in the fields of aeronautic and civil engineering for their superior ability of explosion proof, immunity to electromagnetic interference and high accuracy, especially fitting for measurement applications in harsh environment. In this paper, a novel FBG (fiber Bragg grating) strain sensor, which was packaged in a 1.2mm stainless steel tube by epoxy resin, was developed. Experiments were conducted on the universal material testing machine to calibrate its strain transferring characteristics. The sensor has the advantages of small size, high precision and flexible use, and demonstrates promising potentials. Ten of tube-packaged strain FBG sensors were applied in the vibration experiment of submarine pipeline model. The strain measured by FBG sensor agrees well with the electric resistance strain sensor.

Freshness indices of roasted coffee: monitoring the loss of freshness for single serve capsules and roasted whole beans in different packaging.

PubMed

Glöss, Alexia N; Schönbächler, Barbara; Rast, Markus; Deuber, Louis; Yeretzian, Chahan

2014-01-01

With the growing demand for high-quality coffee, it is becoming increasingly important to establish quantitative measures of the freshness of coffee, or the loss thereof, over time. Indeed, freshness has become a critical quality criterion in the specialty coffee scene, where the aim is to deliver the most pleasant flavor in the cup, from highest quality beans. A series of intensity ratios of selected volatile organic compounds (VOC) in the headspace of coffee (by gas chromatography-mass spectrometry) were revisited, with the aim to establish robust indicators of freshness of coffee - called freshness indices. Roasted whole beans in four different packaging materials and four commercial capsule systems from the Swiss market were investigated over a period of up to one year of storage time. These measurements revealed three types of insight. First, a clear link between barrier properties of the packaging material and the evolution of selected freshness indices was observed. Packaging materials that contain an aluminum layer offer better protection. Second, processing steps prior to packaging are reflected in the absolute values of freshness indices. Third, differences in the standard deviations of freshness-indices for single serve coffee capsule systems are indicative of differences in the consistency among systems, consistency being an important quality attribute of capsules.

Resilience Among Students at the Basic Enlisted Submarine School

DTIC Science & Technology

2016-12-01

reported resilience. The Hayes’ Macro in the Statistical Package for the Social Sciences (SSPS) was used to uncover factors relevant to mediation analysis... Statistical Package for the Social Sciences (SPSS) was used to uncover factors relevant to mediation analysis. Findings suggest that the encouragement of...to Stressful Experiences Scale RTC Recruit Training Command SPSS Statistical Package for the Social Sciences SS Social Support SWB Subjective Well

19 CFR 191.194 - Action on application to participate in compliance program.

Code of Federal Regulations, 2010 CFR

2010-04-01

... to coordinate its decision making on the package both with CBP Headquarters and with the other field drawback offices as appropriate. CBP processing of the package will consist of the review of the information contained therein as well as any additional information requested (see paragraph (a)(2) of this...

Introduction to Social Psychology: Administrative Manual [And] Student Manual [And] Unit Study Guide.

ERIC Educational Resources Information Center

Rankin, Robert E.

This learning package is a three-semester-hour, independent-study course in social psychology designed for postsecondary, external degree students. Keyed to the commercially published textbook "Social Psychology: Explorations in Understanding" (Del Mar, CA: CRM, 1974), the package consists of an administrator manual, a student manual, and a…

The Great War. [Teaching Materials].

ERIC Educational Resources Information Center

Public Broadcasting Service, Washington, DC.

This package of teaching materials is intended to accompany an eight-part film series entitled "The Great War" (i.e., World War I), produced for public television. The package consists of a "teacher's guide,""video segment index,""student resource" materials, and approximately 40 large photographs. The video series is not a war story of battles,…

Decreasing Supermarket Tantrums by Increasing Shopping Tasks: Advantages of Pre-Teaching

ERIC Educational Resources Information Center

Greenwald, Ashley E.; Williams, W. Larry; Seniuk, Holly A.

2014-01-01

A brief training package consisting of pre-teaching of appropriate grocery item--gathering skills and reinforcement for appropriate behavior was used to teach a child diagnosed with autism to remain in a store and participate in shopping without exhibiting tantrums. The training package began with teaching the necessary component skills and…

MicroSIFT Courseware Evaluations (169-198). Set 9. Including Subject and Title Indexes Covering Sets 1-9.

ERIC Educational Resources Information Center

Weaver, Dave, Ed.

This document consists of 30 microcomputer software package evaluations prepared for the MicroSIFT (Microcomputer Software and Information for Teachers) Clearinghouse at the Northwest Regional Educational Laboratory (NWREL). The concise, single-sheet resume describing and evaluating each software package includes source, cost, ability level,…

Chemistry [Sahuarita High School Career Curriculum Project].

ERIC Educational Resources Information Center

Lane, Robert

This course entitled "Chemistry" is one of a series of instructional guides prepared by teachers for the Sahuarita High School (Arizona) Career Curriculum Project. It consists of three packages, the first dealing with solids, liquids and solutions, the second with acids, bases and anions, and the third with cation analysis. These packages are…

Dissemination Package for Transition into Electronics (TIE) Project, October 1979-June 1980.

ERIC Educational Resources Information Center

Evergreen Valley Coll., San Jose, CA.

This dissemination package consists of a variety of advertising materials, forms, questionnaires, tests, and handouts developed as a part of the Transition into Electronics (TIE) Project. (The TIE Project was a project that developed, implemented, and evaluated a model designed to encourage persons to pursue education and training leading to…

A portable system for characterizing wildland fire behavior

Treesearch

Bret Butler; D. Jimenez; J. Forthofer; K. Shannon; Paul Sopko

2010-01-01

A field deployable system for quantifying energy and mass transport in wildland fires is described. The system consists of two enclosures: The first is a sensor/data logger combination package that allows characterization of convective/radiant energy transport in fires. This package contains batteries, a programmable data logger, sensors, and other electronics. The...

Operating Experience and Lessons Learned in the Use of Soft-Sided Packaging for Transportation and Disposal of Low Activity Radioactive Waste

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kapoor, A.; Gordon, S.; Goldston, W.

2013-07-08

This paper describes the operating experience and lessons learned at U.S. Department of Energy (DOE) sites as a result of an evaluation of potential trailer contamination and soft-sided packaging integrity issues related to the disposal of low-level and mixed low-level (LLW/MLLW) radioactive waste shipments. Nearly 4.3 million cubic meters of LLW/MLLW will have been generated and disposed of during fiscal year (FY) 2010 to FY 2015—either at commercial disposal sites or disposal sites owned by DOE. The LLW/MLLW is packaged in several different types of regulatory compliant packaging and transported via highway or rail to disposal sites safely and efficientlymore » in accordance with federal, state, and local regulations and DOE orders. In 1999, DOE supported the development of LLW containers that are more volumetrically efficient, more cost effective, and easier to use as compared to metal or wooden containers that existed at that time. The DOE Idaho National Engineering and Environmental Laboratory (INEEL), working in conjunction with the plastic industry, tested several types of soft-sided waste packaging systems that meet U.S. Department of Transportation requirements for transport of low specific activity and surface contaminated objects. Since then, soft-sided packaging of various capacities have been used successfully by the decontamination and decommissioning (D&D) projects to package, transport, and dispose D&D wastes throughout the DOE complex. The joint team of experts assembled by the Energy Facility Contractors Group from DOE waste generating sites, DOE and commercial waste disposal facilities, and soft-sided packaging suppliers conducted the review of soft-sided packaging operations and transportation of these packages to the disposal sites. As a result of this evaluation, the team developed several recommendations and best practices to prevent or minimize the recurrences of equipment contamination issues and proper use of soft-sided packaging for transport and disposal of waste.« less

Transfer of computer software technology through workshops: The case of fish bioenergetics modeling

USGS Publications Warehouse

Johnson, B.L.

1992-01-01

A three-part program is proposed to promote the availability and use of computer software packages to fishery managers and researchers. The approach consists of journal articles that announce new technologies, technical reports that serve as user's guides, and hands-on workshops that provide direct instruction to new users. Workshops, which allow experienced users to directly instruct novices in software operation and application are important, but often neglected. The author's experience with organizing and conducting bioenergetics modeling workshops suggests the optimal workshop would take 2 days, have 10-15 participants, one computer for every two users, and one instructor for every 5-6 people.

Components of the ALSEP deployed during Apollo 14 first EVA

NASA Image and Video Library

1971-02-05

AS14-67-9376 (5 Feb. 1971) --- Several components of the Apollo lunar surface experiments package (ASLEP) are deployed in this photograph taken during the first Apollo 14 extravehicular activity (EVA). The larger object with antenna is the ALSEP central station (CS). The active seismic experiment (ASE) mortar package assembly is to the rear left of the CS. The charged particle lunar environment experiment (CPLEE) is to the right rear of the CS. A portion of the modularized equipment transporter (MET) can be seen in the left foreground.

Software engineering and data management for automated payload experiment tool

NASA Technical Reports Server (NTRS)

Maddux, Gary A.; Provancha, Anna; Chattam, David

1994-01-01

The Microgravity Projects Office identified a need to develop a software package that will lead experiment developers through the development planning process, obtain necessary information, establish an electronic data exchange avenue, and allow easier manipulation/reformatting of the collected information. An MS-DOS compatible software package called the Automated Payload Experiment Tool (APET) has been developed and delivered. The objective of this task is to expand on the results of the APET work previously performed by UAH and provide versions of the software in a Macintosh and Windows compatible format.

[A philosophical information leaflet to accompany a DSM classification].

PubMed

Kraaijenbrink, J; Kuipers, T; van der Laan, B; Kremer, S

2016-01-01

The introduction of the dsm-5 has re-ignited discussion about the classification of mental disorders. The public may have misconceptions with regard to the nature of the information contained in a dsm-classification. To bring about a conceptual switch so that the professional user of a classification sees it as an aid to diagnosis rather than as a definition of a problem or illness. We devised a 'thought experiment' to serve as a support for dsm classifications. The 'thought experiment' led us to devise a medicine package containing a 'philosophical' information leaflet. This 'thought-experiment', the information leaflet and the medicine package were presented to both students and trainee doctors at the ucp in Groningen and to clinicians at the fpc dr. S. van Mesdag Clinic. Students and trainee doctors were able to make the desired conceptual switch as a result of 'the thought experiment' and with the help they received from the medicine packaging containing the 'philosophical' information leaflet.

Thermal Analysis of the NASA Integrated Vehicle Health Monitoring Experiment Technology for X-Vehicles (NITEX)

NASA Technical Reports Server (NTRS)

Hegab, Hisham E.

2002-01-01

The purpose of this project was to perform a thermal analysis for the NASA Integrated Vehicle Health Monitoring (IVHM) Technology Experiment for X-vehicles (NITEX). This electronics package monitors vehicle sensor information in flight and downlinks vehicle health summary information via telemetry. The experiment will be tested on the X-34 in an unpressurized compartment, in the vicinity of one of the vehicle's liquid oxygen tanks. The transient temperature profile for the electronics package has been determined using finite element analysis for possible mission profiles that will most likely expose the package to the most extreme hot and cold environmental conditions. From the analyses, it was determined that temperature limits for the electronics would be exceeded for the worst case cold environment mission profile. The finite element model used for the analyses was modified to examine the use of insulation to address this problem. Recommendations for insulating the experiment for the cold environment are presented, and were analyzed to determine their effect on a nominal mission profile.

Thermal Analysis Of The NASA Integrated Vehicle Health Monitoring Experiment Technology For X-Vehicles (NITEX)

NASA Technical Reports Server (NTRS)

Hegab, Hisham E.

2001-01-01

The purpose of this project was to perform a thermal analysis for the NASA Integrated Vehicle Health Monitoring (IVHM) Technology Experiment for X-vehicles (NITEX). This electronics package monitors vehicle sensor information in flight and downlinks vehicle health summary information via telemetry. The experiment will be tested on the X-34 in an unpressurized compartment, in the vicinity of one of the vehicle's liquid oxygen tanks. The transient temperature profile for the electronics package has been determined using finite element analysis for possible mission profiles that will most likely expose the package to the most extreme hot and cold environmental conditions. From the analyses, it was determined that temperature limits for the electronics would be exceeded for the worst case cold environment mission profile. The finite element model used for the analyses was modified to examine the use of insulation to address this problem. Recommendations for insulating the experiment for the cold environment are presented, and were analyzed to determine their effect on a nominal mission profile.

Estimating the 'consumer surplus' for branded versus standardised tobacco packaging.

PubMed

Gendall, Philip; Eckert, Christine; Hoek, Janet; Farley, Tessa; Louviere, Jordan; Wilson, Nick; Edwards, Richard

2016-11-01

Tobacco companies question whether standardised (or 'plain') packaging will change smokers' behaviour. We addressed this question by estimating how standardised packaging compared to a proven tobacco control intervention, price increases through excise taxes, thus providing a quantitative measure of standardised packaging's likely effect. We conducted an online study of 311 New Zealand smokers aged 18 years and above that comprised a willingness-to-pay task comparing a branded and a standardised pack at four different price levels, and a choice experiment. The latter used an alternative-specific design, where the alternatives were a branded pack or a standardised pack, with warning theme and price varied for each pack. Respondents had higher purchase likelihoods for the branded pack (with a 30% warning) than the standardised pack (with a 75% warning) at each price level tested, and, on average, were willing to pay approximately 5% more for a branded pack. The choice experiment produced a very similar estimate of 'consumer surplus' for a branded pack. However, the size of the 'consumer surplus' varied between warning themes and by respondents' demographic characteristics. These two experiments suggest standardised packaging and larger warning labels could have a similar overall effect on adult New Zealand smokers as a 5% tobacco price increase. The findings provide further evidence for the efficacy of standardised packaging, which focuses primarily on reducing youth initiation, and suggest this measure will also bring notable benefits to adult smokers. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/.

DATA MANAGEMENT SYSTEM FOR MOBILE SATELLITE PROPAGATION DATA

NASA Technical Reports Server (NTRS)

Kantak, A. V.

1994-01-01

The "Data Management System for Mobile Satellite Propogation" package is a collection of FORTRAN programs and UNIX shell scripts designed to handle the huge amounts of data resulting from Mobile Satellite propogation experiments. These experiments are designed to assist in defining channels for mobile satellite systems. By understanding multipath fading characteristics of the channel, doppler effects, and blockage due to manmade objects as well as natural surroundings, characterization of the channel can be realized. Propogation experiments, then, are performed using a prototype of the system simulating the ultimate product environment. After the data from these experiments is generated, the researcher must access this data with a minimum of effort and to derive some standard results. The programs included in this package manipulate the data files generated by the NASA/JPL Mobile Satellite propogation experiment on an interactive basis. In the experiment, a transmitter operating at 869 MHz was carried to an altitude of 32Km by a stratospheric balloon. A vehicle within the line-of-sight of the transmitter was then driven around, splitting the incoming signal into I and Q channels, and sampling the resulting signal strength at 1000 samples per second. The data was collected at various antenna elavation angles and different times of day generating the ancillary data for the experiment. This package contains a program to convert the binary format of the data generated into standard ASCII format suitable for use with a wide variety of machine architectures. Also included is a UNIX shell-script designed to parse this ASCII file into those records of data that match the researcher's desired values for the ancillary data parameters. In addition, four FORTRAN programs are included to obtain standard quantities from the data. Quantities such as probability of signal level greater than or equal to a specified signal level, probability density of the signal levels, frequency of fade duration, and Fourier Transforms of the sampled data can be generated from the propogation experiment data. All programs in this package are written in either FORTRAN 77 or UNIX shell-scripts. The package does not include test data. The programs were developed in 1987 for use with a UNIX operating system on a DEC MicroVAX computer.

Skylab mobile laboratory

NASA Technical Reports Server (NTRS)

Primeaux, G. R.; Larue, M. A.

1975-01-01

The Skylab mobile laboratory was designed to provide the capability to obtain necessary data on the Skylab crewmen 30 days before lift-off, within 1 hour after recovery, and until preflight physiological baselines were reattained. The mobile laboratory complex consisted of six laboratories that supported cardiovascular, metabolic, nutrition and endocrinology, operational medicine, blood, and microbiology experiments; a utility package; and two shipping containers. The objectives and equipment requirements of the Skylab mobile laboratory and the data acquisition systems are discussed along with processes such as permanently mounting equipment in the individual laboratories and methods of testing and transporting the units. The operational performance, in terms of amounts of data collected, and the concept of mobile laboratories for medical and scientific experiments are evaluated. The Skylab mobile laboratory succeeded in facilitating the data collection and sample preservation associated with the three Skylab manned flights.

Test report dot 7A type a liquid packaging

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ketusky, E. T.; Brandjes, C.; Benoit, T. J.

This test report documents the performance of Savannah River National Laboratory’s (SRNL’s) U.S. Department of Transportation (DOT) Specification 7A; General Packaging, Type A shielded liquid shipping packaging and compliance with the regulatory requirements of Title 49 of the Code of Federal Regulations (CFR). The primary use of this packaging design is for the transport of radioactive liquids of up to 1.3 liters in an unshielded configuration and up to 113 mL of radioactive liquids in a shielded configuration, with no more than an A2 quantity in either configuration, over public highways and/or commercial aircraft. The contents are liquid radioactive materialsmore » sufficiently shielded and within the activity limits specified in173.435 or 173.433 for A2 (normal form) materials, as well as within the analyzed thermal heat limits. Any contents must be compatibly packaged and must be compatible with the packaging. The basic packaging design is based on the U.S. Department of Energy’s (DOE’s) Model 9979 Type A fissile shipping packaging designed and tested by SRNL. The shielded liquid configuration consists of the outer and inner drums of the 9979 package with additional low density polyethylene (LDPE) dunnage nesting a tungsten shielded cask assembly (WSCA) within the 30-gallon inner drum. The packaging model for the DOT Specification 7A, Type A liquids packaging is HVYTAL.« less

Identification of a Novel Reference Gene for Apple Transcriptional Profiling under Postharvest Conditions

PubMed Central

Storch, Tatiane Timm; Pegoraro, Camila; Finatto, Taciane; Quecini, Vera; Rombaldi, Cesar Valmor; Girardi, César Luis

2015-01-01

Reverse Transcription quantitative PCR (RT-qPCR) is one of the most important techniques for gene expression profiling due to its high sensibility and reproducibility. However, the reliability of the results is highly dependent on data normalization, performed by comparisons between the expression profiles of the genes of interest against those of constitutively expressed, reference genes. Although the technique is widely used in fruit postharvest experiments, the transcription stability of reference genes has not been thoroughly investigated under these experimental conditions. Thus, we have determined the transcriptional profile, under these conditions, of three genes commonly used as reference—ACTIN (MdACT), PROTEIN DISULPHIDE ISOMERASE (MdPDI) and UBIQUITIN-CONJUGATING ENZYME E2 (MdUBC)—along with two novel candidates—HISTONE 1 (MdH1) and NUCLEOSSOME ASSEMBLY 1 PROTEIN (MdNAP1). The expression profile of the genes was investigated throughout five experiments, with three of them encompassing the postharvest period and the other two, consisting of developmental and spatial phases. The transcriptional stability was comparatively investigated using four distinct software packages: BestKeeper, NormFinder, geNorm and DataAssist. Gene ranking results for transcriptional stability were similar for the investigated software packages, with the exception of BestKeeper. The classic reference gene MdUBC ranked among the most stably transcribed in all investigated experimental conditions. Transcript accumulation profiles for the novel reference candidate gene MdH1 were stable throughout the tested conditions, especially in experiments encompassing the postharvest period. Thus, our results present a novel reference gene for postharvest experiments in apple and reinforce the importance of checking the transcription profile of reference genes under the experimental conditions of interest. PMID:25774904

Identification of a novel reference gene for apple transcriptional profiling under postharvest conditions.

PubMed

Storch, Tatiane Timm; Pegoraro, Camila; Finatto, Taciane; Quecini, Vera; Rombaldi, Cesar Valmor; Girardi, César Luis

2015-01-01

Reverse Transcription quantitative PCR (RT-qPCR) is one of the most important techniques for gene expression profiling due to its high sensibility and reproducibility. However, the reliability of the results is highly dependent on data normalization, performed by comparisons between the expression profiles of the genes of interest against those of constitutively expressed, reference genes. Although the technique is widely used in fruit postharvest experiments, the transcription stability of reference genes has not been thoroughly investigated under these experimental conditions. Thus, we have determined the transcriptional profile, under these conditions, of three genes commonly used as reference--ACTIN (MdACT), PROTEIN DISULPHIDE ISOMERASE (MdPDI) and UBIQUITIN-CONJUGATING ENZYME E2 (MdUBC)--along with two novel candidates--HISTONE 1 (MdH1) and NUCLEOSSOME ASSEMBLY 1 PROTEIN (MdNAP1). The expression profile of the genes was investigated throughout five experiments, with three of them encompassing the postharvest period and the other two, consisting of developmental and spatial phases. The transcriptional stability was comparatively investigated using four distinct software packages: BestKeeper, NormFinder, geNorm and DataAssist. Gene ranking results for transcriptional stability were similar for the investigated software packages, with the exception of BestKeeper. The classic reference gene MdUBC ranked among the most stably transcribed in all investigated experimental conditions. Transcript accumulation profiles for the novel reference candidate gene MdH1 were stable throughout the tested conditions, especially in experiments encompassing the postharvest period. Thus, our results present a novel reference gene for postharvest experiments in apple and reinforce the importance of checking the transcription profile of reference genes under the experimental conditions of interest.

“One for all and all for one”: consensus-building within communities in rural India on their health microinsurance package

PubMed Central

Dror, David M; Panda, Pradeep; May, Christina; Majumdar, Atanu; Koren, Ruth

2014-01-01

Introduction This study deals with consensus by poor persons in the informal sector in rural India on the benefit-package of their community-based health insurance (CBHI). In this article we describe the process of involving rural poor in benefit-package design and assess the underlying reasons for choices they made and their ability to reach group consensus. Methods The benefit-package selection process entailed four steps: narrowing down the options by community representatives, plus three Choosing Healthplans All Together (CHAT) rounds conducted among female members of self-help groups. We use mixed-methods and four sources of data: baseline study, CHAT exercises, in-depth interviews, and evaluation questionnaires. We define consensus as a community resolution reached by discussion, considering all opinions, and to which everyone agrees. We use the coefficient of unalikeability to express consensus quantitatively (as variability of categorical variables) rather than just categorically (as a binomial Yes/No). Findings The coefficient of unalikeability decreased consistently over consecutive CHAT rounds, reaching zero (ie, 100% consensus) in two locations, and confirmed gradual adoption of consensus. Evaluation interviews revealed that the wish to be part of a consensus was dominant in all locations. The in-depth interviews indicated that people enjoyed the participatory deliberations, were satisfied with the selection, and that group decisions reflected a consensus rather than majority. Moreover, evidence suggests that pre-selectors and communities aimed to enhance the likelihood that many households would benefit from CBHI. Conclusion The voluntary and contributory CBHI relies on an engaging experience with others to validate perceived priorities of the target group. The strongest motive for choice was the wish to join a consensus (more than price or package-composition) and the intention that many members should benefit. The degree of consensus improved with iterative CHAT rounds. Harnessing group consensus requires catalytic intervention, as the process is not spontaneous. PMID:25120378

Effect of thermal cycling ramp rate on CSP assembly reliability

NASA Technical Reports Server (NTRS)

Ghaffarian, R.

2001-01-01

A JPL-led chip scale package consortium of enterprises recently joined together to pool in-kind resources for developing the quality and reliability of chip scale packages for a variety of projects. The experience of the consortium in building more than 150 test vehicle assemblies, single and double sided multilayer PWBs, and the environmental test results has now been published as a chip scale package guidelines document.

PlasmaPy: initial development of a Python package for plasma physics

NASA Astrophysics Data System (ADS)

Murphy, Nicholas; Leonard, Andrew J.; Stańczak, Dominik; Haggerty, Colby C.; Parashar, Tulasi N.; Huang, Yu-Min; PlasmaPy Community

2017-10-01

We report on initial development of PlasmaPy: an open source community-driven Python package for plasma physics. PlasmaPy seeks to provide core functionality that is needed for the formation of a fully open source Python ecosystem for plasma physics. PlasmaPy prioritizes code readability, consistency, and maintainability while using best practices for scientific computing such as version control, continuous integration testing, embedding documentation in code, and code review. We discuss our current and planned capabilities, including features presently under development. The development roadmap includes features such as fluid and particle simulation capabilities, a Grad-Shafranov solver, a dispersion relation solver, atomic data retrieval methods, and tools to analyze simulations and experiments. We describe several ways to contribute to PlasmaPy. PlasmaPy has a code of conduct and is being developed under a BSD license, with a version 0.1 release planned for 2018. The success of PlasmaPy depends on active community involvement, so anyone interested in contributing to this project should contact the authors. This work was partially supported by the U.S. Department of Energy.

Characterization of the Resource Potential of Martian Soil using the Integrated Dust/Soil Experiment Package (IDEP)

NASA Technical Reports Server (NTRS)

Cooper, Bonnie L.; Mckay, David S.; Allen, Carlton C.; Hoffman, John H.; Gittleman, Mark E.

1997-01-01

The Integrated Dust/Soil Experiment Package (IDEP) is a suite of instruments that can detect and quantify the abundances of useful raw materials on Mars. We focus here on its capability for resource characterization in the martian soil; however, it is also capable of detecting and quantifying gases in the atmosphere. This paper describes the scientific rationale and the engineering design behind the IDEP.

Test program for transmitter experiment package and heat pipe system for the communications technology satellite

NASA Technical Reports Server (NTRS)

Depauw, J. F.; Reader, K. E.; Staskus, J. V.

1976-01-01

The test program is described for the 200 watt transmitter experiment package and the variable conductance heat pipe system which are components of the high-power transponder aboard the Communications Technology Satellite. The program includes qualification tests to demonstrate design adequacy, acceptance tests to expose latent defects in flight hardware, and development tests to integrate the components into the transponder system and to demonstrate compatibility.

Examination of Shipping Packages 9975-02694 and 9975-02729

DOE Office of Scientific and Technical Information (OSTI.GOV)

Daugherty, W.

SRNL has assisted in the examination of two 9975 shipping packages (9975-02694 and 9975-02729) following their use for storage of nuclear material in K-Area Complex (KAC). Both of these were targeted for examination because they were exposed to water from a leaking expansion joint during storage. When first opened in KAC, the axial gap was found to be in excess of the 1 inch maximum criterion, signaling the potential for degradation of the fiberboard overpack and drum. Within each package the highest fiberboard moisture levels were observed in the bottom layers, but no mold was observed in either package. Themore » fiberboard in each package appeared to retain good integrity consistent with non-degraded material. Minor corrosion was also observed on these drums along the lower stitch welds and on several closure bolts.« less

GillesPy: A Python Package for Stochastic Model Building and Simulation.

PubMed

Abel, John H; Drawert, Brian; Hellander, Andreas; Petzold, Linda R

2016-09-01

GillesPy is an open-source Python package for model construction and simulation of stochastic biochemical systems. GillesPy consists of a Python framework for model building and an interface to the StochKit2 suite of efficient simulation algorithms based on the Gillespie stochastic simulation algorithms (SSA). To enable intuitive model construction and seamless integration into the scientific Python stack, we present an easy to understand, action-oriented programming interface. Here, we describe the components of this package and provide a detailed example relevant to the computational biology community.

GillesPy: A Python Package for Stochastic Model Building and Simulation

PubMed Central

Abel, John H.; Drawert, Brian; Hellander, Andreas; Petzold, Linda R.

2017-01-01

GillesPy is an open-source Python package for model construction and simulation of stochastic biochemical systems. GillesPy consists of a Python framework for model building and an interface to the StochKit2 suite of efficient simulation algorithms based on the Gillespie stochastic simulation algorithms (SSA). To enable intuitive model construction and seamless integration into the scientific Python stack, we present an easy to understand, action-oriented programming interface. Here, we describe the components of this package and provide a detailed example relevant to the computational biology community. PMID:28630888

The Geography of Germany: Lessons for Teaching the Five Themes of Geography. Social Studies, Grades 9-12. Update 2002.

ERIC Educational Resources Information Center

Blankenship, Glen; Tinkler, D. William

This instructional package, consisting of a text and 13 transparencies, is designed for high school classrooms. The five lessons in the instructional package relate to the "Five Themes of Geography" (Location, Place, Human-Environment Interaction, Movement, and Region) as promoted by the National Geographic Society. The lessons are…

Cleanup Verification Package for the 600-47 Waste Site

DOE Office of Scientific and Technical Information (OSTI.GOV)

M. J. Cutlip

This cleanup verification package documents completion of interim remedial action for the 600-47 waste site. This site consisted of several areas of surface debris and contamination near the banks of the Columbia River across from Johnson Island. Contaminated material identified in field surveys included four areas of soil, wood, nuts, bolts, and other metal debris.

Preserving Knowledge: The Case for Alkaline Paper. ARL Briefing Package Number 3.

ERIC Educational Resources Information Center

Association of Research Libraries, Washington, DC.

This briefing package consists of a compilation of over 15 papers, fact sheets, and other materials focusing on the use of acid-free papers in books and other publications. The document contains the following: Executive Summary and List of Contents; Some Frequently Asked Questions; "Paper Preservation in Library Collections: Basic Information.…

Cultural Reflections: Work, Politics, and Daily Life in Germany. Social Studies Grades 9-12. Update 2002.

ERIC Educational Resources Information Center

Blankenship, Glen; Tinkler, D. William

This instructional package, consisting of a text and 16 transparencies, is designed for the high school classroom. The three lessons in this instructional package are: (1) "The German Worker" (six activities); (2) "Government in Germany" (seven activities); and (3) "Culture and Daily Life in Germany" (six activities).…

Apprentice Machinist (AFSC 53130), Volumes 1-4, and Change Supplement (AFSC 42730).

ERIC Educational Resources Information Center

Air Univ., Gunter AFS, Ala. Extension Course Inst.

This four-volume student learning package is designed for use by Air Force personnel enrolled in a self-study extension course for apprentice machinists. The package consists of four volumes of instructional text and four workbooks. Covered in the individual volumes are machine shop fundamentals, lathe work, shaper and contour machine work, and…

Cleanup Verification Package for the 118-F-7, 100-F Miscellaneous Hardware Storage Vault

DOE Office of Scientific and Technical Information (OSTI.GOV)

M. J. Appel

2006-11-02

This cleanup verification package documents completion of remedial action for the 118-F-7, 100-F Miscellaneous Hardware Storage Vault. The site consisted of an inactive solid waste storage vault used for temporary storage of slightly contaminated reactor parts that could be recovered and reused for the 100-F Area reactor operations.

Training Teachers to Enhance the Play Skills of Young Children with Developmental Disabilities during Outdoor Time by Embedding Instructional Interactions

ERIC Educational Resources Information Center

Martin, Christian A.; Drasgow, Erik; Halle, James W.

2015-01-01

We created and evaluated a professional development package for training four teachers to embed instructional interactions during outdoor time to enhance the play skills of young children with significant developmental disabilities. The instructional package included an initial 20-min session that consisted of providing written and verbal…

A flexible CPW package for a 30 GHz MMIC amplifier. [coplanar waveguide

NASA Technical Reports Server (NTRS)

Simons, Rainee N.; Taub, Susan R.

1992-01-01

A novel package, which consists of a carrier housing, has been developed for monolithic-millimeter wave Integrated Circuit amplifiers which operate at 30 giga-Hz. The carrier has coplanar waveguide (CPW) interconnects and provides heat-sinking, tuning, and cascading capabilities. The housing provides electrical isolation, mechanical protection and a feed-thru for biasing.

Sigma 2 Graphic Display Software Program Description

NASA Technical Reports Server (NTRS)

Johnson, B. T.

1973-01-01

A general purpose, user oriented graphic support package was implemented. A comprehensive description of the two software components comprising this package is given: Display Librarian and Display Controller. These programs have been implemented in FORTRAN on the XDS Sigma 2 Computer Facility. This facility consists of an XDS Sigma 2 general purpose computer coupled to a Computek Display Terminal.

The DOSIS -Experiment onboard the Columbus Laboratory of the International Space Station -First Mission Results from the Active DOSTEL Instruments

NASA Astrophysics Data System (ADS)

Burmeister, Soenke; Berger, Thomas; Beaujean, Rudolf; Boehme, Matthias; Haumann, Lutz; Kortmann, Onno; Labrenz, Johannes; Reitz, Guenther

Besides the effects of the microgravity environment, and the psychological and psychosocial problems encountered in confined spaces, radiation is the main health detriment for long dura-tion human space missions. The radiation environment encountered in space differs in nature from that on earth, consisting mostly of high energetic ions from protons up to iron, resulting in radiation levels far exceeding the ones encountered on earth for occupational radiation workers. Accurate knowledge of the physical characteristics of the space radiation field in dependence on the solar activity, the orbital parameters and the different shielding configurations of the International Space Station ISS is therefore needed. For the investigation of the spatial and temporal distribution of the radiation field inside the European COLUMBUS module the DLR experiment DOSIS (Dose Distribution Inside the ISS) was launched on July 15th 2009 with STS-127 to the ISS. The experimental package was transferred from the Space Shuttle into COLUMBUS on July 18th. It consists in a first part of a combination of passive detector packages (PDP) distributed at 11 locations inside the European Columbus Laboratory. The second part are two active radiation detectors (DOSTELs) with a DDPU (DOSIS Data and Power Unit) in a nomex pouch (DOSIS MAIN BOX) mounted at a fixed location beneath the European Physiology Module (EPM) inside COLUMBUS. After the successful installation the active part has been activated on the 18th July 2009. Each of the DOSTEL units consists of two 6.93 cm PIPS silicon detectors forming a telescope with an opening angle of 120. The two DOSTELs are mounted with their telescope axis perpendicular to each other to investigate anisotropies of the radiation field inside the COLUMBUS module especially during the passes through the South Atlantic Anomaly (SAA) and during Solar Particle Events (SPEs). The data from the DOSTEL units are transferred to ground via the EPM rack which is activated approximately every four weeks for this action. The first data downlink was performed on July 31st 2009. First Results for the DOSTEL measurements such as count rate profiles, dose rates and LET spectra will be presented in comparison to the data obtained by other experiments.

Effect of packaging materials on shelf life and quality of banana cultivars (Musa spp.).

PubMed

Hailu, M; Seyoum Workneh, T; Belew, D

2014-11-01

This study was carried out to evaluate the effect of packaging materials on the shelf life of three banana cultivars. Four packaging materials, namely, perforated low density polyethylene bag, perforated high density polyethylene bag, dried banana leaf, teff straw and no packaging materials (control) were used with three banana cultivars, locally known as, Poyo, Giant Cavendish and Williams I. The experiment was carried out in Randomized Complete Block Design in a factorial combination with three replications. Physical parameters including weight loss, peel colour, peel thickness, pulp thickness, pulp to peel ratio, pulp firmness, pulp dry matter, decay, loss percent of marketability were assessed every 3 days. Banana remained marketable for 36 days in the high density polyethylene and low density polyethylene bags, and for 18 days in banana leaf and teff straw packaging treatments. Unpackaged fruits remained marketable for 15 days only. Fruits that were not packaged lost their weight by 24.0 % whereas fruits packaged in banana leaf and teff straw became unmarketable with final weight loss of 19.8 % and 20.9 %, respectively. Packaged fruits remained well until 36th days of storage with final weight loss of only 8.2 % and 9.20 %, respectively. Starting from green mature stage, the colour of the banana peel changed to yellow and this process was found to be fast for unpackaged fruits. Packaging maintained the peel and the pulp thickness, firmness, dry matter and pulp to peel ratio was kept lower. Decay loss for unpackaged banana fruits was16 % at the end of date 15, whereas the decay loss of fruits packaged using high density and low density polyethylene bags were 43.0 % and 41.2 %, respectively at the end of the 36th day of the experiment. It can, thus, be concluded that packaging of banana fruits in high density and low density polyethylene bags resulted in longer shelf life and improved quality of the produce followed by packaging in dried banana leaf and teff straw.

DNA Packaging in Bacteriophage: Is Twist Important?

PubMed Central

Spakowitz, Andrew James; Wang, Zhen-Gang

2005-01-01

We study the packaging of DNA into a bacteriophage capsid using computer simulation, specifically focusing on the potential impact of twist on the final packaged conformation. We perform two dynamic simulations of packaging a polymer chain into a spherical confinement: one where the chain end is rotated as it is fed, and one where the chain is fed without end rotation. The final packaged conformation exhibits distinct differences in these two cases: the packaged conformation from feeding with rotation exhibits a spool-like character that is consistent with experimental and previous theoretical work, whereas feeding without rotation results in a folded conformation inconsistent with a spool conformation. The chain segment density shows a layered structure, which is more pronounced for packaging with rotation. However, in both cases, the conformation is marked by frequent jumps of the polymer chain from layer to layer, potentially influencing the ability to disentangle during subsequent ejection. Ejection simulations with and without Brownian forces show that Brownian forces are necessary to achieve complete ejection of the polymer chain in the absence of external forces. PMID:15805174

DNA packaging in bacteriophage: is twist important?

PubMed

Spakowitz, Andrew James; Wang, Zhen-Gang

2005-06-01

We study the packaging of DNA into a bacteriophage capsid using computer simulation, specifically focusing on the potential impact of twist on the final packaged conformation. We perform two dynamic simulations of packaging a polymer chain into a spherical confinement: one where the chain end is rotated as it is fed, and one where the chain is fed without end rotation. The final packaged conformation exhibits distinct differences in these two cases: the packaged conformation from feeding with rotation exhibits a spool-like character that is consistent with experimental and previous theoretical work, whereas feeding without rotation results in a folded conformation inconsistent with a spool conformation. The chain segment density shows a layered structure, which is more pronounced for packaging with rotation. However, in both cases, the conformation is marked by frequent jumps of the polymer chain from layer to layer, potentially influencing the ability to disentangle during subsequent ejection. Ejection simulations with and without Brownian forces show that Brownian forces are necessary to achieve complete ejection of the polymer chain in the absence of external forces.

Restoration and Reexamination of Apollo Lunar Dust Detector Data from Original Telemetry Files

NASA Technical Reports Server (NTRS)

McBride, M. J.; Williams, David R.; Hills, H. Kent

2012-01-01

We are recovering the original telemetry (Figure I) from the Apollo Dust, Thermal, Radiation Environment Monitor (DTREM) experiment, more commonly known as the Dust Detector, and producing full time resolution (54 second) data sets for release through the Planetary Data System (PDS). The primary objective of the experiment was to evaluate the effect of dust deposition, temperature, and radiation damage on solar cells on the lunar surface. The monitor was a small box consisting of three solar cells and thermistors mounted on the ALSEP (Apollo Lunar Surface Experiments Package) central station. The Dust Detector was carried on Apollo's 11, 12, 14 and 15. The Apollo 11 DTREM was powered by solar cells and only operated for a few months as planned. The Apollo 12, 14, and 15 detectors operated for 5 to 7 years, returning data every 54 seconds, consisting of voltage outputs from the three solar cells and temperatures measured by the three thermistors. The telemetry was received at ground stations and held on the Apollo Housekeeping (known as "Word 33") tapes. made available to the National Space Science Data Center (NSSDC) by Yosio Nakamura (University of Texas Institute for Geophysics). We have converted selected parts of the telemetry into uncalibrated and calibrated output voltages and temperatures.

Plain packaging of cigarettes and smoking behavior: study protocol for a randomized controlled study.

PubMed

Maynard, Olivia M; Leonards, Ute; Attwood, Angela S; Bauld, Linda; Hogarth, Lee; Munafò, Marcus R

2014-06-25

Previous research on the effects of plain packaging has largely relied on self-report measures. Here we describe the protocol of a randomized controlled trial investigating the effect of the plain packaging of cigarettes on smoking behavior in a real-world setting. In a parallel group randomization design, 128 daily cigarette smokers (50% male, 50% female) will attend an initial screening session and be assigned plain or branded packs of cigarettes to smoke for a full day. Plain packs will be those currently used in Australia where plain packaging has been introduced, while branded packs will be those currently used in the United Kingdom. Our primary study outcomes will be smoking behavior (self-reported number of cigarettes smoked and volume of smoke inhaled per cigarette as measured using a smoking topography device). Secondary outcomes measured pre- and post-intervention will be smoking urges, motivation to quit smoking, and perceived taste of the cigarettes. Secondary outcomes measured post-intervention only will be experience of smoking from the cigarette pack, overall experience of smoking, attributes of the cigarette pack, perceptions of the on-packet health warnings, behavior changes, views on plain packaging, and the rewarding value of smoking. Sex differences will be explored for all analyses. This study is novel in its approach to assessing the impact of plain packaging on actual smoking behavior. This research will help inform policymakers about the effectiveness of plain packaging as a tobacco control measure. Current Controlled Trials ISRCTN52982308 (registered 27 June 2013).

Basic analysis of reflectometry data software package for the analysis of multilayered structures according to reflectometry data

DOE Office of Scientific and Technical Information (OSTI.GOV)

Astaf'ev, S. B., E-mail: bard@ns.crys.ras.ru; Shchedrin, B. M.; Yanusova, L. G.

2012-01-15

The main principles of developing the Basic Analysis of Reflectometry Data (BARD) software package, which is aimed at obtaining a unified (standardized) tool for analyzing the structure of thin multilayer films and nanostructures of different nature based on reflectometry data, are considered. This software package contains both traditionally used procedures for processing reflectometry data and the authors' original developments on the basis of new methods for carrying out and analyzing reflectometry experiments. The structure of the package, its functional possibilities, examples of application, and prospects of development are reviewed.

HiTC: exploration of high-throughput ‘C’ experiments

PubMed Central

Servant, Nicolas; Lajoie, Bryan R.; Nora, Elphège P.; Giorgetti, Luca; Chen, Chong-Jian; Heard, Edith; Dekker, Job; Barillot, Emmanuel

2012-01-01

Summary: The R/Bioconductor package HiTC facilitates the exploration of high-throughput 3C-based data. It allows users to import and export ‘C’ data, to transform, normalize, annotate and visualize interaction maps. The package operates within the Bioconductor framework and thus offers new opportunities for future development in this field. Availability and implementation: The R package HiTC is available from the Bioconductor website. A detailed vignette provides additional documentation and help for using the package. Contact: nicolas.servant@curie.fr Supplementary information: Supplementary data are available at Bioinformatics online. PMID:22923296

DOE Office of Scientific and Technical Information (OSTI.GOV)

Singledecker, Steven John

The purpose of this document is to describe the waste stream from Z-Pinch Residual Waste Project that due to worker safety concerns and operational efficiency is a candidate for blending Transuranic and low level waste together and can be safely packaged as low-level waste consistent with DOE Order 435.1 requirements and NRC guidance 10 CFR 61.42. This waste stream consists of the Pu-ICE post-shot containment systems, including plutonium targets, generated from the Z Machine experiments requested by LANL and conducted by SNL/NM. In the past, this TRU waste was shipped back to LANL after Sandia sends the TRU data packagemore » to LANL to certify the characterization (by CCP), transport and disposition at WIPP (CBFO) per LANL MOU-0066. The Low Level Waste is managed, characterized, shipped and disposed of at NNSS by SNL/NM per Sandia MOU # 11-S-560.« less

TRANSIENT SUPPRESSION PACKAGING FOR REDUCED EMISSIONS FROM ROTARY KILN INCINERATORS

EPA Science Inventory

Experiments were performed on a 73 kW rotary kiln incinerator simulator to determine whether innovative waste packaging designs might reduce transient emissions of products of incomplete combustion due to batch charging of containerized liquid surrogate waste compounds bound on g...

Air-cooling characteristics of simulated grape packages

DOE Office of Scientific and Technical Information (OSTI.GOV)

Frederick, R.L.; Comunian, F.

Experimental simulation of the external forced convection on the outside of grape packages was performed. Average heat transfer coefficients for air flow around such containers were found to range from 8 to 13.4 W/(m[sup 2]K). A physical description of the convective process was formulated on the basis of data obtained in three types of experiment. Expressions for the average heat transfer coefficient from single packages in air flow were proposed.

On the Rocks: Microbiological Quality and Microbial Diversity of Packaged Ice in Southern California.

PubMed

Lee, Kun Ho; Ab Samad, Liana S; Lwin, Phillip M; Riedel, Stefan F; Magin, Ashley; Bashir, Mina; Vaishampayan, Parag A; Lin, Wei-Jen

2017-06-01

Ice is defined as a food and is frequently used in direct contact with food and beverages. Packaged ice is commercially produced and can be easily found in grocery and convenience stores. However, the quality and safety of packaged ice products is not consistent. The Packaged Ice Quality Control Standards manual (PIQCS) published by the International Packaged Ice Association provides the quality and processing standards for packaged ice produced by its members. Packaged ice produced on the premise of stores (on-site packaged ice) is not required to be in compliance with these standards. In this study, packaged ice produced by manufacturing plants or by in-store bagger (ISB) machines and on-site packaged ice were compared for their microbiological quality and microbial diversity. Our results revealed that 19% of the 120 on-site packaged ice samples did not meet the PIQCS microbial limit of 500 CFU/mL (or g) and also the absence of coliforms and Escherichia coli . Staphylococci were found in 34% of the on-site packaged ice samples, most likely through contamination from the packaging workers. None of the ISB and manufactured packaged ice samples had unacceptable microbial levels, and all were devoid of staphylococci. Salmonella was absent in all samples analyzed in this study. Microbial community analysis of ice based on 16S/18S rRNA targeted sequencing revealed a much higher microbial diversity and abundance in the on-site packaged ice than in the ISB ice. Proteobacteria, especially Alphaproteobacteria and Betaproteobacteria, were the dominant bacterial groups in all samples tested. Most of these bacteria were oligotrophic; however, a few opportunistic or potential pathogens were found at low levels in the on-site packaged ice but not in the ISB packaged ice. The types of microbes identified may provide information needed to investigate potential sources of contamination. Our data also suggest a need for enforcement of processing standards during the on-site packaging of ice.

Detailed design package for design of a video system providing optimal visual information for controlling payload and experiment operations with television

NASA Technical Reports Server (NTRS)

1975-01-01

A detailed description of a video system for controlling space shuttle payloads and experiments is presented in the preliminary design review and critical design review, first and second engineering design reports respectively, and in the final report submitted jointly with the design package. The material contained in the four subsequent sections of the package contains system descriptions, design data, and specifications for the recommended 2-view system. Section 2 contains diagrams relating to the simulation test configuration of the 2-view system. Section 3 contains descriptions and drawings of the deliverable breadboard equipment. A description of the recommended system is contained in Section 4 with equipment specifications in Section 5.

BOW SHOCK FRAGMENTATION DRIVEN BY A THERMAL INSTABILITY IN LABORATORY ASTROPHYSICS EXPERIMENTS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Suzuki-Vidal, F.; Lebedev, S. V.; Pickworth, L. A.

The role of radiative cooling during the evolution of a bow shock was studied in laboratory-astrophysics experiments that are scalable to bow shocks present in jets from young stellar objects. The laboratory bow shock is formed during the collision of two counterstreaming, supersonic plasma jets produced by an opposing pair of radial foil Z-pinches driven by the current pulse from the MAGPIE pulsed-power generator. The jets have different flow velocities in the laboratory frame, and the experiments are driven over many times the characteristic cooling timescale. The initially smooth bow shock rapidly develops small-scale nonuniformities over temporal and spatial scalesmore » that are consistent with a thermal instability triggered by strong radiative cooling in the shock. The growth of these perturbations eventually results in a global fragmentation of the bow shock front. The formation of a thermal instability is supported by analysis of the plasma cooling function calculated for the experimental conditions with the radiative packages ABAKO/RAPCAL.« less

TargetSearch--a Bioconductor package for the efficient preprocessing of GC-MS metabolite profiling data.

PubMed

Cuadros-Inostroza, Alvaro; Caldana, Camila; Redestig, Henning; Kusano, Miyako; Lisec, Jan; Peña-Cortés, Hugo; Willmitzer, Lothar; Hannah, Matthew A

2009-12-16

Metabolite profiling, the simultaneous quantification of multiple metabolites in an experiment, is becoming increasingly popular, particularly with the rise of systems-level biology. The workhorse in this field is gas-chromatography hyphenated with mass spectrometry (GC-MS). The high-throughput of this technology coupled with a demand for large experiments has led to data pre-processing, i.e. the quantification of metabolites across samples, becoming a major bottleneck. Existing software has several limitations, including restricted maximum sample size, systematic errors and low flexibility. However, the biggest limitation is that the resulting data usually require extensive hand-curation, which is subjective and can typically take several days to weeks. We introduce the TargetSearch package, an open source tool which is a flexible and accurate method for pre-processing even very large numbers of GC-MS samples within hours. We developed a novel strategy to iteratively correct and update retention time indices for searching and identifying metabolites. The package is written in the R programming language with computationally intensive functions written in C for speed and performance. The package includes a graphical user interface to allow easy use by those unfamiliar with R. TargetSearch allows fast and accurate data pre-processing for GC-MS experiments and overcomes the sample number limitations and manual curation requirements of existing software. We validate our method by carrying out an analysis against both a set of known chemical standard mixtures and of a biological experiment. In addition we demonstrate its capabilities and speed by comparing it with other GC-MS pre-processing tools. We believe this package will greatly ease current bottlenecks and facilitate the analysis of metabolic profiling data.

TargetSearch - a Bioconductor package for the efficient preprocessing of GC-MS metabolite profiling data

PubMed Central

2009-01-01

Background Metabolite profiling, the simultaneous quantification of multiple metabolites in an experiment, is becoming increasingly popular, particularly with the rise of systems-level biology. The workhorse in this field is gas-chromatography hyphenated with mass spectrometry (GC-MS). The high-throughput of this technology coupled with a demand for large experiments has led to data pre-processing, i.e. the quantification of metabolites across samples, becoming a major bottleneck. Existing software has several limitations, including restricted maximum sample size, systematic errors and low flexibility. However, the biggest limitation is that the resulting data usually require extensive hand-curation, which is subjective and can typically take several days to weeks. Results We introduce the TargetSearch package, an open source tool which is a flexible and accurate method for pre-processing even very large numbers of GC-MS samples within hours. We developed a novel strategy to iteratively correct and update retention time indices for searching and identifying metabolites. The package is written in the R programming language with computationally intensive functions written in C for speed and performance. The package includes a graphical user interface to allow easy use by those unfamiliar with R. Conclusions TargetSearch allows fast and accurate data pre-processing for GC-MS experiments and overcomes the sample number limitations and manual curation requirements of existing software. We validate our method by carrying out an analysis against both a set of known chemical standard mixtures and of a biological experiment. In addition we demonstrate its capabilities and speed by comparing it with other GC-MS pre-processing tools. We believe this package will greatly ease current bottlenecks and facilitate the analysis of metabolic profiling data. PMID:20015393

Description of the three axis low-g accelerometer package

NASA Technical Reports Server (NTRS)

Amalavage, A. J.; Fikes, E. H.; Berry, E. H.

1978-01-01

The three axis low-g accelerometer package designed for use on the Space Processing Application Rocket (SPAR) Program is described. The package consists of the following major sections: (1) three Kearfott model 2412 accelerometers mounted in an orthogonal triad configuration on a temperature controlled, thermally isolated cube, (2) the accelerometer servoelectronics (printed circuit cards PC-6 through PC-12), and (3) the signal conditioner (printed circuit cards PC-15 and PC-16). The measurement range is 0 + or - 0.031 g with a quantization of 1.1 x 10 to the 7th power g. The package was flown successfully on six SPAR launches with the Black Brant booster. These flights provide approximately 300 s of free fall or zero-g environment.

Problem-based learning: effects on student’s scientific reasoning skills in science

NASA Astrophysics Data System (ADS)

Wulandari, F. E.; Shofiyah, N.

2018-04-01

This research aimed to develop instructional package of problem-based learning to enhance student’s scientific reasoning from concrete to formal reasoning skills level. The instructional package was developed using the Dick and Carey Model. Subject of this study was instructional package of problem-based learning which was consisting of lesson plan, handout, student’s worksheet, and scientific reasoning test. The instructional package was tried out on 4th semester science education students of Universitas Muhammadiyah Sidoarjo by using the one-group pre-test post-test design. The data of scientific reasoning skills was collected by making use of the test. The findings showed that the developed instructional package reflecting problem-based learning was feasible to be implemented in classroom. Furthermore, through applying the problem-based learning, students could dominate formal scientific reasoning skills in terms of functionality and proportional reasoning, control variables, and theoretical reasoning.

16 CFR 1702.8 - Human experience data.

Code of Federal Regulations, 2010 CFR

2010-01-01

... Commercial Practices CONSUMER PRODUCT SAFETY COMMISSION POISON PREVENTION PACKAGING ACT OF 1970 REGULATIONS PETITIONS FOR EXEMPTIONS FROM POISON PREVENTION PACKAGING ACT REQUIREMENTS; PETITION PROCEDURES AND... Application (NDA), 21 CFR part 314, a summary of the relevant data should be provided. The entire NDA and IND...

Chemistry and the Periodic Table: Teacher's Guide Levels A, B, and C. Preliminary Limited Edition.

ERIC Educational Resources Information Center

Cambridge Physics Outlet, Woburn, MA. Education Programs Dept.

This is a two-part curriculum package for the teaching of chemistry and the periodic table. The first part, the Teacher's Guide, contains information necessary for using the equipment in a typical classroom including learning goals, vocabulary, math skills, and sample data for each activity. The second part of the package consists of photocopy…

The Structure of the Atom: Teacher's Guide Levels A, B, and C. Preliminary Limited Edition.

ERIC Educational Resources Information Center

Cambridge Physics Outlet, Woburn, MA. Education Programs Dept.

This is a two-part curriculum package for teaching the structure of atoms. The first part--the Teacher's Guide--contains information necessary for using the equipment in a typical classroom including learning goals, vocabulary, math skills, and sample data for each activity. The second part of the package consists of photocopy masters for a set of…

Computer Lab Tools for Science: An Analysis of Commercially Available Science Interfacing Software for Microcomputers. A Quarterly Report.

ERIC Educational Resources Information Center

Weaver, Dave

Science interfacing packages (also known as microcomputer-based laboratories or probeware) generally consist of a set of programs on disks, a user's manual, and hardware which includes one or more sensory devices. Together with a microcomputer they combine to make a powerful data acquisition and analysis tool. Packages are available for accurately…

Effects of a Graphic Organizer Training Package on the Persuasive Writing of Middle School Students with Autism

ERIC Educational Resources Information Center

Bishop, Anne E.; Sawyer, Mary; Alber-Morgan, Sheila R.; Boggs, Melissa

2015-01-01

This study examined the effects of a graphic organizer intervention package on the quality and quantity of persuasive writing of three middle school students with Autism Spectrum Disorder (ASD). The intervention included a 3-day training which consisted of explicit instruction on the components of a persuasive essay, modeling and guided practice…

Asian Basic 4 Adaptations. Basic 4 Food Groups. Nutrients for Health. Calcium: A Dietary Mineral. Iron: A Dietary Mineral. Guide to Good Eating.

ERIC Educational Resources Information Center

Mortensen, JoAnn; And Others

This package consists of various bilingual instructional materials for use in helping Indochinese refugees learn basic nutrition skills. Included in the package are translations in English, Vietnamese, and Lao of booklets outlining guidelines for adapting Indochinese dietary habits to incorporate foods available in the United States, including…

The Effectiveness of Computerized Instructional Packages on Concept Acquisition and Improving Academic Achievement among Female Deaf Students in KSA

ERIC Educational Resources Information Center

Bagabas, Hanan Ali

2016-01-01

The current study aimed to investigate the effectiveness of computerized instructional packages on concept acquisition and improving academic achievement among deaf students in Saudi Arabia. The sample consisted of (16) third-grade female deaf students in prep stage for the first semester of the academic year 2013/2014, randomly selected from…

Using FIESTA , an R-based tool for analysts, to look at temporal trends in forest estimates

Treesearch

Tracey S. Frescino; Paul L. Patterson; Elizabeth A. Freeman; Gretchen G. Moisen

2012-01-01

FIESTA (Forest Inventory Estimation for Analysis) is a user-friendly R package that supports the production of estimates for forest resources based on procedures from Bechtold and Patterson (2005). The package produces output consistent with current tools available for the Forest Inventory and Analysis National Program, such as FIDO (Forest Inventory Data Online) and...

DEsubs: an R package for flexible identification of differentially expressed subpathways using RNA-seq experiments.

PubMed

Vrahatis, Aristidis G; Balomenos, Panos; Tsakalidis, Athanasios K; Bezerianos, Anastasios

2016-12-15

DEsubs is a network-based systems biology R package that extracts disease-perturbed subpathways within a pathway network as recorded by RNA-seq experiments. It contains an extensive and customized framework with a broad range of operation modes at all stages of the subpathway analysis, enabling so a case-specific approach. The operation modes include pathway network construction and processing, subpathway extraction, visualization and enrichment analysis with regard to various biological and pharmacological features. Its capabilities render DEsubs a tool-guide for both the modeler and experimentalist for the identification of more robust systems-level drug targets and biomarkers for complex diseases. DEsubs is implemented as an R package following Bioconductor guidelines: http://bioconductor.org/packages/DEsubs/ CONTACT: tassos.bezerianos@nus.edu.sgSupplementary information: Supplementary data are available at Bioinformatics online. © The Author 2016. Published by Oxford University Press. All rights reserved. For Permissions, please e-mail: journals.permissions@oup.com.

Auxiliary propulsion system flight package

NASA Technical Reports Server (NTRS)

Collett, C. R.

1987-01-01

Hughes Aircraft Company developed qualified and integrated flight, a flight test Ion Auxiliary Propulsion System (IAPS), on an Air Force technology satellite. The IAPS Flight Package consists of two identical Thruster Subsystems and a Diagnostic Subsystem. Each thruster subsystem (TSS) is comprised of an 8-cm ion Thruster-Gimbal-Beam Shield Unit (TGBSU); Power Electronics Unit; Digital Controller and Interface Unit (DCIU); and Propellant Tank, Valve and Feed Unit (PTVFU) plus the requisite cables. The Diagnostic Subsystem (DSS) includes four types of sensors for measuring the effect of the ion thrusters on the spacecraft and the surrounding plasma. Flight qualifications of IAPS, prior to installation on the spacecraft, consisted of performance, vibration and thermal-vacuum testing at the unit level, and thermal-vacuum testing at the subsystem level. Mutual compatibility between IAPS and the host spacecraft was demonstrated during a series of performance and environmental tests after the IAPS Flight Package was installed on the spacecraft. After a spacecraft acoustic test, performance of the ion thrusters was reverified by removing the TGBSUs for a thorough performance test at Hughes Research Laboratories (HRL). The TGBSUs were then reinstalled on the spacecraft. The IAPS Flight Package is ready for flight testing when Shuttle flights are resumed.

Multi-scale fracture networks within layered shallow water tight carbonates

NASA Astrophysics Data System (ADS)

Panza, Elisa; Agosta, Fabrizio; Rustichelli, Andrea; Vinciguerra, Sergio; Zambrano, Miller; Prosser, Giacomo; Tondi, Emanuele

2015-04-01

The work is aimed at deciphering the contribution of background deformation and persistent fracture zones on the fluid flow properties of tight platform carbonates. Taking advantage of 3D exposures present in the Murge area of southern Italy, the fracture networks crosscutting at different scales the layered Cretaceous limestone of the Altamura Fm. were analyzed. The rock multi-layer is characterized by 10's of cm-thick, sub-horizontal, laterally continuous carbonate beds. Each bed commonly represents a shallowing-upward peritidal cycle made up of homogeneous micritic limestones grading upward to cm-thick stromatolitic limestones and/or fenestral limestones. The bed interfaces are formed by sharp maximum flooding surfaces. Porosity measurements carried out on 40 limestone samples collected from a single carbonate bed show values ranging between 0,5% and 5,5%. Background deformation includes both stratabound and non-stratabound fractures. The former elements consist of bed-perpendicular joints and sheared joints, which are confined within a single bed and often displace small, bed-parallel stylolites. Non-stratabound fractures consist of incipient, cm offset, sub-vertical strike-slip faults, which crosscut the bed interfaces. The aforementioned elements are often confined within individual bed-packages, which are identified by presence of pronounced surfaces locally marked by veneers of reddish clayey paleosoils. Persistent fracture zones consist of 10's of m-high, 10's of cm-offset strike-slip faults that offset the bed-package interfaces and are confined within individual bed-packages association. Laterally discontinuous, cm- to a few m-thick paleokarstic breccia levels separate the different bed-packages associations. Persistent fracture zones include asymmetric fractured damage zones and mm-thick veneers of discontinuous fault rocks. The fracture networks that pervasively crosscut the study limestone multi-layer are investigated by mean of scanline and scanarea methodologies. The dimensional, spatial and scaling properties of both stratabound and non-stratabound fractures are documented along single beds and bed-packages, respectively. Persistent fracture zones are studied from individual bed-package associations. By computing the intensity, height distribution, aspect ratio, aperture of each fracture/fault set, DFN (Discrete Fracture Network) models are built for the aforementioned different scales of observation. DFN models of single beds and bed-packages include stratabound and non-stratabound fractures. Differently, the DFN model of a bed-packages association also includes persistent fracture zones and related damage zones. To check the results of our computations, we also build up a smaller scale, 1m3 geocellular volume in which fractures are inserted one at time in the model. All DFN models do not include the matrix porosity. Porosity and 3D permeability (Kx, Ky, Kz) values are obtained as outputs of the DFN models. The results are consistent with the most prominet set of non-stratabound fractures being the major control on the petrophysical properties of both single beds and bed-packages. As expected, the persistent fractures zones strongly affect both porosity and permeability of the bed-packages association. The results of ongoing laboratory analyses on representative limestone samples not only will provide a quantitative assessment of the physical properties of the matrix in terms of porosity and permeability, but also will shed new light on the geometry, density and anisotropy of microfractures and their role on fluid flow properties.

Packaging of MEMS/MOEMS and nanodevices: reliability, testing, and characterization aspects

NASA Astrophysics Data System (ADS)

Tekin, Tolga; Ngo, Ha-Duong; Wittler, Olaf; Bouhlal, Bouchaib; Lang, Klaus-Dieter

2011-02-01

The last decade witnessed an explosive growth in research and development efforts devoted to MEMS devices and packaging. The successfully developed MEMS devices are, for example inkjet, pressure sensors, silicon microphones, accelerometers, gyroscopes, MOEMS, micro fuel cells and emerging MEMS. For the next decade, MEMS/MOEMS and nanodevice based products will penetrate into IT, telecommunications, automotive, defense, life sciences, medical and implantable applications. Forecasts say the MEMS market to be $14 billion by 2012. The packaging cost of MEMS/MOEMS products in general is about 70 percent. Unlike today's electronics IC packaging, their packaging are custom-built and difficult due to the moving structural elements. In order for the moving elements of a MEMS device to move effectively in a well-controlled atmosphere, hermetic sealing of the MEMS device in a cap is necessary. For some MEMS devices, such as resonators and gyroscopes, vacuum packaging is required. Usually, the cap is processed at the wafer level, and thus MEMS packaging is truly a wafer level packaging. In terms of MEMS/MOEMS and nanodevice packaging, there are still many critical issues need to be addressed due to the increasing integration density supported by 3D heterogeneous integration of multi-physic components/layers consisting of photonics, electronics, rf, plasmonics, and wireless. The infrastructure of MEMS/MOEMS and nanodevices and their packaging is not well established yet. Generic packaging platform technologies are not available. Some of critical issues have been studied intensively in the last years. In this paper we will discuss about processes, reliability, testing and characterization of MEMS/MOEMS and nanodevice packaging.

Mission requirements: Second Skylab mission SL-3

NASA Technical Reports Server (NTRS)

1972-01-01

Complete SL-3 mission objectives and requirements, as revised 1 February 1972 (Rev. 6), are presented. Detailed test objectives are also given on the medical experiments, Apollo Telescope Mount experiments, Earth Resources Experiment Package, and corollary experiments and environmental microbiology experiments.

ReadqPCR and NormqPCR: R packages for the reading, quality checking and normalisation of RT-qPCR quantification cycle (Cq) data.

PubMed

Perkins, James R; Dawes, John M; McMahon, Steve B; Bennett, David L H; Orengo, Christine; Kohl, Matthias

2012-07-02

Measuring gene transcription using real-time reverse transcription polymerase chain reaction (RT-qPCR) technology is a mainstay of molecular biology. Technologies now exist to measure the abundance of many transcripts in parallel. The selection of the optimal reference gene for the normalisation of this data is a recurring problem, and several algorithms have been developed in order to solve it. So far nothing in R exists to unite these methods, together with other functions to read in and normalise the data using the chosen reference gene(s). We have developed two R/Bioconductor packages, ReadqPCR and NormqPCR, intended for a user with some experience with high-throughput data analysis using R, who wishes to use R to analyse RT-qPCR data. We illustrate their potential use in a workflow analysing a generic RT-qPCR experiment, and apply this to a real dataset. Packages are available from http://www.bioconductor.org/packages/release/bioc/html/ReadqPCR.htmland http://www.bioconductor.org/packages/release/bioc/html/NormqPCR.html These packages increase the repetoire of RT-qPCR analysis tools available to the R user and allow them to (amongst other things) read their data into R, hold it in an ExpressionSet compatible R object, choose appropriate reference genes, normalise the data and look for differential expression between samples.

A threshold gas Cerenkov detector for the spin asymmetries of the nucleon experiment

DOE PAGES

Armstrong, Whitney R.; Choi, Seonho; Kaczanowicz, Ed; ...

2015-09-26

In this study, we report on the design, construction, commissioning, and performance of a threshold gas Cerenkov counter in an open configuration, which operates in a high luminosity environment and produces a high photo-electron yield. Part of a unique open geometry detector package known as the Big Electron Telescope Array, this Cerenkov counter served to identify scattered electrons and reject produced pions in an inclusive scattering experiment known as the Spin Asymmetries of the Nucleon Experiment E07-003 at the Thomas Jefferson National Accelerator Facility (TJNAF) also known as Jefferson Lab. The experiment consisted of a measurement of double spin asymmetriesmore » A || and A ⊥ of a polarized electron beam impinging on a polarized ammonia target. The Cerenkov counter's performance is characterised by a yield of about 20 photoelectrons per electron or positron track. Thanks to this large number of photoelectrons per track, the Cerenkov counter had enough resolution to identify electron-positron pairs from the conversion of photons resulting mainly from π 0 decays.« less

KSC-as11-40-5927

NASA Image and Video Library

1969-07-20

JOHNSON SPACE CENTER, HOUSTON, TEXAS - Man's first landing on the Moon was accomplished at 4:17 p.m. today as Lunar Module "Eagle" touched down gently on the Sea of Tranquility on the east side of the Moon. Astronaut Edwin E. Aldrin Jr., Lunar Module Pilot, removes scientific experiment packages from a stowage area in the Lunar Module's descent stage. Left behind on the lunar surface by Aldrin and Neil A. Armstrong, Apollo 11 commander, were a Passive Seismic Experiments Package and a Laser-Ranging Retro-Reflector.

Simulations and experiments of aperiodic and multiplexed gratings in volume holographic imaging systems

PubMed Central

Luo, Yuan; Castro, Jose; Barton, Jennifer K.; Kostuk, Raymond K.; Barbastathis, George

2010-01-01

A new methodology describing the effects of aperiodic and multiplexed gratings in volume holographic imaging systems (VHIS) is presented. The aperiodic gratings are treated as an ensemble of localized planar gratings using coupled wave methods in conjunction with sequential and non-sequential ray-tracing techniques to accurately predict volumetric diffraction effects in VHIS. Our approach can be applied to aperiodic, multiplexed gratings and used to theoretically predict the performance of multiplexed volume holographic gratings within a volume hologram for VHIS. We present simulation and experimental results for the aperiodic and multiplexed imaging gratings formed in PQ-PMMA at 488nm and probed with a spherical wave at 633nm. Simulation results based on our approach that can be easily implemented in ray-tracing packages such as Zemax® are confirmed with experiments and show proof of consistency and usefulness of the proposed models. PMID:20940823

Teaching Science and Mathematics Subjects Using the Excel Spreadsheet Package

ERIC Educational Resources Information Center

Ibrahim, Dogan

2009-01-01

The teaching of scientific subjects usually require laboratories where students can put the theory they have learned into practice. Traditionally, electronic programmable calculators, dedicated software, or expensive software simulation packages, such as MATLAB have been used to simulate scientific experiments. Recently, spreadsheet programs have…

JUICE: complementarity of the payload in adressing the mission science objectives

NASA Astrophysics Data System (ADS)

Titov, Dmitri; Barabash, Stas; Bruzzone, Lorenzo; Dougherty, Michele; Erd, Christian; Fletcher, Leigh; Gare, Philippe; Gladstone, Randall; Grasset, Olivier; Gurvits, Leonid; Hartogh, Paul; Hussmann, Hauke; Iess, Luciano; Jaumann, Ralf; Langevin, Yves; Palumbo, Pasquale; Piccioni, Giuseppe; Wahlund, Jan-Erik

2014-05-01

JUpiter ICy moons Explorer (JUICE) will perform detailed investigations of Jupiter and its system with particular emphasis on Ganymede as a planetary body and potential habitat. The overarching theme for JUICE is: The emergence of habitable worlds around gas giants. At Ganymede, the mission will characterize in detail the ocean layers; provide topographical, geological and compositional mapping of the surface; study the physical properties of the icy crusts; characterize the internal mass distribution, investigate the exosphere; study Ganymede's intrinsic magnetic field and its interactions with the Jovian magnetosphere. For Europa, the focus will be on the non-ice chemistry, understanding the formation of surface features and subsurface sounding of the icy crust over recently active regions. Callisto will be explored as a witness of the early solar system. JUICE will perform a multidisciplinary investigation of the Jupiter system as an archetype for gas giants. The circulation, meteorology, chemistry and structure of the Jovian atmosphere will be studied from the cloud tops to the thermosphere. The focus in Jupiter's magnetosphere will include an investigation of the three dimensional properties of the magnetodisc and in-depth study of the coupling processes within the magnetosphere, ionosphere and thermosphere. Aurora and radio emissions will be elucidated. JUICE will study the moons' interactions with the magnetosphere, gravitational coupling and long-term tidal evolution of the Galilean satellites. JUICE highly capable scientific payload includes 10 state-of-the-art instruments onboard the spacecraft plus one experiment that uses the spacecraft telecommunication system with ground-based radio telescopes. The remote sensing package includes a high-resolution multi-band visible imager (JANUS) and spectro-imaging capabilities from the ultraviolet to the sub-millimetre wavelengths (MAJIS, UVS, SWI). A geophysical package consists of a laser altimeter (GALA) and a radar sounder (RIME) for exploring the surface and subsurface of the moons, and a radio science experiment (3GM) to probe the atmospheres of Jupiter and its satellites and to perform measurements of the gravity fields. An in situ package comprises a powerful particle environment package (PEP), a magnetometer (J-MAG) and a radio and plasma wave instrument (RPWI), including electric fields sensors and a Langmuir probe. An experiment (PRIDE) using ground-based Very-Long-Baseline Interferometry (VLBI) will provide precise determination of the moons ephemerides. The instruments will work together to achieve mission science objectives that otherwise cannot be achieved by a single experiment. For instance, joint J-MAG, 3GM, GALA and JANUS observations would constrain thickness of the ice shell, ocean depth and conductivity. SWI, 3GM and UVS would complement each other in the temperature sounding of the Jupiter atmosphere. The complex coupling between magnetosphere and atmosphere of Jupiter will be jointly studied by combination of aurora imaging (UVS, MAJIS, JANUS) and plasma and fields measurements (J-MAG, RPWI, PEP). The talk will give an overview of the JUICE payload focusing on complementarity and synergy between the experiments.

Effect of modified atmosphere packaging on the course of physical and chemical changes in chilled muscle tissue of silver carp (Hypophthalmichthys molitrix, V.).

PubMed

Jezek, F; Buchtová, H

2012-01-01

The effect of two types of modified atmosphere (MA1: 69% N2, 25% CO2, 5% O2, 1% CO; MA2: 70% N2, 30% CO2) on changes in physical and chemical parameters (pH, a(w)--water activity, TVBN - total volatile basic nitrogen, TMA - trimethylamine, FFA - free fatty acids, PV - peroxide value, TBA--thiobarbituric acid) in muscle tissues of the silver carp was monitored in the study. The samples were stored at temperatures +2 +/- 2 degrees C for 18 days. Changes in gas volumes (CO2 and O2) in MAs were also monitored. CO2 levels increased in MA1 but decreased in MA2. At the end of 18 days of storage, a significantly (P < 0.01) lower water activity (a(w)) levels were found in samples packaged under MA1, in contrast to samples packaged under MA2 where water activity values showed considerable fluctuation. Variations in pH values in the two types of MA showed similar trends. Sample pH gradually decreased until day 9 of storage. On day 11, muscle tissue pH increased markedly and then began to decrease again. The overall decrease in pH values was more profound in samples packaged under MA1. TVBN and TMA levels in samples packaged under the two types of MAs remained almost identical until day 9 of the experiment. Later, however, significantly (P < 0.01) higher levels of both parameters were found in muscle tissues packaged under MA1. FFA concentrations in silver carp samples in MA1 were significantly lower (P < 0.01) throughout the experiment. The PV increased significantly in both muscle samples tested. Greater fluctuations in this parameter's values throughout the experiment were observed in samples packaged under MA2. Faster rates of oxidation (P < 0.01) were found in samples packaged under MA1 starting on day 9. Maximum TBA values in MA1 and MA2 were observed on days 14 and 18 of the experiment, respectively. From the course of proteolytic and oxidative changes point of view, the more appropriate combination of gases for silver carp storage seems to be the mixture of 70% N2 and 30% CO2 (MA2), which allows for muscle storage of up to 9 days. We recommend TVBN as a suitable indicator of freshness, and TBA assay as a suitable indicator of the extent of oxidative processes.

Radiometric packaging of uncooled bolometric infrared focal plane arrays

NASA Astrophysics Data System (ADS)

García-Blanco, Sonia; Pope, Timothy; Côté, Patrice; Leclerc, Mélanie; Ngo Phong, Linh; Châteauneuf, François

2017-11-01

INO has a wide experience in the design and fabrication of different kinds of microbolometer focal plane arrays (FPAs). In particular, a 512x3 pixel microbolometer FPA has been selected as the sensor for the New Infrared Sensor Technology (NIRST) instrument, one of the payloads of the SACD/Aquarius mission. In order to make the absolute temperature measurements necessary for many infrared Earth observation applications, the microbolometer FPA must be integrated into a package offering a very stable thermal environment. The radiometric packaging technology developed at INO presents an innovative approach since it was conceived to be modular and adaptable for the packaging of different microbolometer FPAs and for different sets of assembly requirements without need for requalification of the assembly process. The development of the radiometric packaging technology has broadened the position of INO as a supplier of radiometric detector modules integrating FPAs of microbolometers inside a radiometric package capable of achieving the requirements of different space missions. This paper gives an overview of the design of INO's radiometric package. Key performance parameters are also discussed and the test campaign conducted with the radiometric package is presented.

Development of an e-learning package on Service-Learning for university teachers: experience from Hong Kong.

PubMed

Shek, Daniel T L; Chan, Stephen C F

2013-01-01

To help university teachers to understand Service-Learning and develop Service-Learning subjects, a 3-h+ e-learning package was developed at The Hong Kong Polytechnic University (PolyU). There are seven units in this e-learning package: introduction session (Unit 1), what is Service-Learning? (Unit 2), impact and benefits of Service-Learning (Unit 3), myths and positive attitudes toward Service-Learning (Unit 4), developing a Service-Learning subject at PolyU (Unit 5), self-reflection about Service-Learning (Unit 6), and concluding session (Unit 7). To understand the views of the users on the e-learning package, the package was offered before formal launching. For the first offering, three focus group sessions were held. Results showed that the users were satisfied with the structural arrangement of the e-learning package and agreed that the e-learning package was useful for them to understand more about Service-Learning. For the second offering, colleagues were generally satisfied with the e-learning package and demonstrated gain in knowledge on Service-Learning. Suggestions for improvement were noted.

Effecting aging time of epoxy molding compound to molding process for integrated circuit packaging

NASA Astrophysics Data System (ADS)

Tachapitunsuk, Jirayu; Ugsornrat, Kessararat; Srisuwitthanon, Warayoot; Thonglor, Panakamon

2017-09-01

This research studied about effecting aging time of epoxy molding compound (EMC) that effect to reliability performance of integrated circuit (IC) package in molding process. Molding process is so important of IC packaging process for protecting IC chip (or die) from temperature and humidity environment using encapsulated EMC. For general molding process, EMC are stored in the frozen at 5°C and left at room temperature at 25 °C for aging time on self before molding of die onto lead frame is 24 hours. The aging time effect to reliability performance of IC package due to different temperature and humidity inside the package. In experiment, aging time of EMC were varied from 0 to 24 hours for molding process of SOIC-8L packages. For analysis, these packages were tested by x-ray and scanning acoustic microscope to analyze properties of EMC with an aging time and also analyzed delamination, internal void, and wire sweep inside the packages with different aging time. The results revealed that different aging time of EMC effect to properties and reliability performance of molding process.

ATIC Flight Data Processing

NASA Technical Reports Server (NTRS)

Ahn, H. S.; Whitaker, Ann F. (Technical Monitor)

2001-01-01

The first flight of the Advanced Thin Ionization Calorimeter (ATIC) experiment from McMurdo, Antarctica lasted for 16 days, starting in December, 2000. The ATIC instrument consists of a fully active 320-crystal, 960-channel Bismuth Germanate (BGO) calorimeter, 202 scintillator strips in 3 hodoscopes interleaved with a graphite target, and a 4480-pixel silicon matrix charge detector. We have developed an Object Oriented data processing package based on ROOT. In this paper, we will describe the data processing scheme used in handling the accumulated 45 GB of flight data. We will also discuss trigger issues by comparing the measured energy-dependent trigger efficiency with its simulation and calibration issues by considering the time-dependence of housekeeping information, etc.

Radar Unix: a complete package for GPR data processing

NASA Astrophysics Data System (ADS)

Grandjean, Gilles; Durand, Herve

1999-03-01

A complete package for ground penetrating radar data interpretation including data processing, forward modeling and a case history database consultation is presented. Running on an Unix operating system, its architecture consists of a graphical user interface generating batch files transmitted to a library of processing routines. This design allows a better software maintenance and the possibility for the user to run processing or modeling batch files by itself and differed in time. A case history data base is available and consists of an hypertext document which can be consulted by using a standard HTML browser. All the software specifications are presented through a realistic example.

Testing a structural model for viral DNA packaging motor function by optical tweezers measurements, site directed mutagenesis, and molecular dynamics calculations

NASA Astrophysics Data System (ADS)

Keller, Nicholas A.; Migliori, Amy D.; Arya, Gaurav; Rao, Venigalla B.; Smith, Douglas E.

2013-09-01

Many double-stranded DNA viruses employ a molecular motor to package DNA into preformed capsid shells. Based on structures of phage T4 motor proteins determined by X-ray crystallography and cryo-electron microscopy, Rao, Rossmann and coworkers recently proposed a structural model for motor function. They proposed that DNA is ratcheted by a large conformational change driven by electrostatic interactions between charged residues at an interface between two globular domains of the motor protein. We have conducted experiments to test this model by studying the effect on packaging under applied load of site-directed changes altering these residues. We observe significant impairment of packaging activity including reductions in packaging rate, percent time packaging, and time active under high load. We show that these measured impairments correlate well with alterations in free energies associated with the conformational change predicted by molecular dynamics simulations.

Stored product mites (Acari: Astigmata) infesting food in various types of packaging.

PubMed

Hubert, Jan; Nesvorna, Marta; Volek, Vlado

2015-02-01

From 2008 to 2014, stored product mites have been reported from prepackaged dried food on the market in the Czech Republic. The infestation was by Carpoglyphus lactis (L.) in dried fruits and Tyrophagus putrescentiae (Schrank) in dog feed. The infestation is presumably caused by poor protection of the packages. We compared various packaging methods for their resistance to mites using dried apricots and dog feed in laboratory experiments. The trial packages included nine different plastic films, monofilm, duplex and triplex, and one type of plastic cup (ten replicates per packaging type). All packaging materials are available on the Czech market for dried food products. The samples of dried food were professionally packed in a factory and packaged dried apricots were exposed to C. lactis and dog food to T. putrescentiae. After 3 months of exposure, the infestation and mite density of the prepackaged food was assessed. Mites were found to infest six types of packages. Of the packaging types with mites, 1-5 samples were infested and the maximum abundance was 1,900 mites g(-1) of dried food. Mites entered the prepackaged food by faulty sealing. Inadequate sealing is suggested to be the major cause of the emerged infestation of dried food.

Accessing packaged food and beverages in hospital. Exploring experiences of patients and staff.

PubMed

Bell, A F; Walton, K; Chevis, J S; Davies, K; Manson, C; Wypych, A; Yoxall, A; Kirkby, J; Alexander, N

2013-01-01

Food and beverage packaging has been identified as a contributing factor to malnutrition among elderly patients in hospitals. The focus of this research was to describe the types of food and beverage packaging used in NSW hospitals, determine the 'problematic' packaging from the users' perspective, investigate the effect of hand strength on the ability to open the packaging and to survey users' (patients and staff) views on the 'accessibility' of the packaging. The study was conducted in the Illawarra region of NSW, Australia. Participants (140 mostly elderly inpatients and 64 staff members) were recruited from four local public hospitals. Data were collected using interviews, questionnaires, observations and grip strength testing. Several food and beverage packages were found difficult to open by at least 40% of patients. These included milk and juices (52%), cereal (49%), condiments (46%), tetra packs (40%) and water bottles (40%). The difficulties were attributed to 'fiddly' packaging, hand strength and vision; however, only tetra packs demonstrated a relationship between time taken to open and hand strength, suggesting other aspects of hand function may be more important than strength when opening food and beverage packages. Crown Copyright © 2012. Published by Elsevier Ltd. All rights reserved.

An SU-8 liquid cell for surface acoustic wave biosensors

NASA Astrophysics Data System (ADS)

Francis, Laurent A.; Friedt, Jean-Michel; Bartic, Carmen; Campitelli, Andrew

2004-08-01

One significant challenge facing biosensor development is packaging. For surface acoustic wave based biosensors, packaging influences the general sensing performance. The acoustic wave is generated and received thanks to interdigital transducers and the separation between the transducers defines the sensing area. Liquids used in biosensing experiments lead to an attenuation of the acoustic signal while in contact with the transducers. We have developed a liquid cell based on photodefinable epoxy SU-8 that prevents the presence of liquid on the transducers, has a small disturbance effect on the propagation of the acoustic wave, does not interfere with the biochemical sensing event, and leads to an integrated sensor system with reproducible properties. The liquid cell is achieved in two steps. In a first step, the SU-8 is precisely patterned around the transducers to define 120 μm thick walls. In a second step and after the dicing of the sensors, a glass capping is placed manually and glued on top of the SU-8 walls. This design approach is an improvement compared to the more classical solution consisting of a pre-molded cell that must be pressed against the device in order to avoid leaks, with negative consequences on the reproducibility of the experimental results. We demonstrate the effectiveness of our approach by protein adsorption monitoring. The packaging materials do not interfere with the biomolecules and have a high chemical resistance. For future developments, wafer level bonding of the quartz capping onto the SU-8 walls is envisioned.

A review of the findings of the plasma diagnostic package and associated laboratory experiments: Implications of large body/plasma interactions for future space technology

NASA Technical Reports Server (NTRS)

Murphy, Gerald B.; Lonngren, Karl E.

1986-01-01

The discoveries and experiments of the Plasma Diagnostic Package (PDP) on the OSS 1 and Spacelab 2 missions are reviewed, these results are compared with those of other space and laboratory experiments, and the implications for the understanding of large body interactions in a low Earth orbit (LEO) plasma environment are discussed. First a brief review of the PDP investigation, its instrumentation and experiments is presented. Next a summary of PDP results along with a comparison of those results with similar space or laboratory experiments is given. Last of all the implications of these results in terms of understanding fundamental physical processes that take place with large bodies in LEO is discussed and experiments to deal with these vital questions are suggested.

MicroSIFT Courseware Evaluation. [Set 13 (294-319), Set 14 (320-361), with Hardware (HRD) and Subject (SBJ) Indexes to Both Sets.

ERIC Educational Resources Information Center

Northwest Regional Educational Lab., Portland, OR.

This document consists of 68 microcomputer software package evaluations prepared by MicroSIFT (Microcomputer Software and Information for Teachers) Clearinghouse at the Northwest Regional Education Laboratory. There are 26 packages in set 13 and 42 in set 14. Each software review lists producer, time and place of evaluation, cost, ability level,…

Effectiveness of E-Content Package on Teaching IUPAC Nomenclature of Organic Chemistry at Undergraduate Level

ERIC Educational Resources Information Center

Devendiran, G.; Vakkil, M.

2017-01-01

This study attempts to discover the effectiveness of an e-content package when teaching IUPAC nomenclature of organic chemistry at the undergraduate level. The study consisted of a Pre-test-Post-test Non Equivalent Groups Design, and the sample of 71 (n = 71) students were drawn from two colleges. The overall study was divided into two groups, an…

A Pilot Investigation Comparing Instructional Packages for MTS Training: "Manual Alone" vs. "Manual-Plus-Computer-Aided Personalized System of Instruction"

ERIC Educational Resources Information Center

Oliveira, Marileide; Goyos, Celso; Pear, Joseph

2012-01-01

Matching-to-sample (MTS) training consists of presenting a stimulus as a sample followed by stimuli called comparisons from which a subject makes a choice. This study presents results of a pilot investigation comparing two packages for teaching university students to conduct MTS training. Two groups--control and experimental--with 2 participants…

An Innovative Learning Model for Computation in First Year Mathematics

ERIC Educational Resources Information Center

Tonkes, E. J.; Loch, B. I.; Stace, A. W.

2005-01-01

MATLAB is a sophisticated software tool for numerical analysis and visualization. The University of Queensland has adopted Matlab as its official teaching package across large first year mathematics courses. In the past, the package has met severe resistance from students who have not appreciated their computational experience. Several main…

Learning Activity Package, Physical Science. LAP Numbers 8, 9, 10, and 11.

ERIC Educational Resources Information Center

Williams, G. J.

These four units of the Learning Activity Packages (LAPs) for individualized instruction in physical science cover nuclear reactions, alpha and beta particles, atomic radiation, medical use of nuclear energy, fission, fusion, simple machines, Newton's laws of motion, electricity, currents, electromagnetism, Oersted's experiment, sound, light,…

Modeling and MBL: Software Tools for Science.

ERIC Educational Resources Information Center

Tinker, Robert F.

Recent technological advances and new software packages put unprecedented power for experimenting and theory-building in the hands of students at all levels. Microcomputer-based laboratory (MBL) and model-solving tools illustrate the educational potential of the technology. These tools include modeling software and three MBL packages (which are…

View of the Challenger's payload bay and the Plasma Diagnostic package

NASA Image and Video Library

1985-08-01

51F-33-024 (29 July-6 Aug 1985) --- The Challenger's remote manipulator system (RMS) arm grasps the plasma diagnostics package (PDP) over the experiment-laden cargo bay of the earth orbiting spacecraft. The instrument pointing system, in a resting mode here, is prominent in the bay.

A predictive transport modeling code for ICRF-heated tokamaks

DOE Office of Scientific and Technical Information (OSTI.GOV)

Phillips, C.K.; Hwang, D.Q.; Houlberg, W.

In this report, a detailed description of the physic included in the WHIST/RAZE package as well as a few illustrative examples of the capabilities of the package will be presented. An in depth analysis of ICRF heating experiments using WHIST/RAZE will be discussed in a forthcoming report. A general overview of philosophy behind the structure of the WHIST/RAZE package, a summary of the features of the WHIST code, and a description of the interface to the RAZE subroutines are presented in section 2 of this report. Details of the physics contained in the RAZE code are examined in section 3.more » Sample results from the package follow in section 4, with concluding remarks and a discussion of possible improvements to the package discussed in section 5.« less

A predictive transport modeling code for ICRF-heated tokamaks

DOE Office of Scientific and Technical Information (OSTI.GOV)

Phillips, C.K.; Hwang, D.Q.; Houlberg, W.

1992-02-01

In this report, a detailed description of the physic included in the WHIST/RAZE package as well as a few illustrative examples of the capabilities of the package will be presented. An in depth analysis of ICRF heating experiments using WHIST/RAZE will be discussed in a forthcoming report. A general overview of philosophy behind the structure of the WHIST/RAZE package, a summary of the features of the WHIST code, and a description of the interface to the RAZE subroutines are presented in section 2 of this report. Details of the physics contained in the RAZE code are examined in section 3.more » Sample results from the package follow in section 4, with concluding remarks and a discussion of possible improvements to the package discussed in section 5.« less

WiLE: A Mathematica package for weak coupling expansion of Wilson loops in ABJ(M) theory

NASA Astrophysics Data System (ADS)

Preti, M.

2018-06-01

We present WiLE, a Mathematica® package designed to perform the weak coupling expansion of any Wilson loop in ABJ(M) theory at arbitrary perturbative order. For a given set of fields on the loop and internal vertices, the package displays all the possible Feynman diagrams and their integral representations. The user can also choose to exclude non planar diagrams, tadpoles and self-energies. Through the use of interactive input windows, the package should be easily accessible to users with little or no previous experience. The package manual provides some pedagogical examples and the computation of all ladder diagrams at three-loop relevant for the cusp anomalous dimension in ABJ(M). The latter application gives also support to some recent results computed in different contexts.

Introduction in IND and recursive partitioning

NASA Technical Reports Server (NTRS)

Buntine, Wray; Caruana, Rich

1991-01-01

This manual describes the IND package for learning tree classifiers from data. The package is an integrated C and C shell re-implementation of tree learning routines such as CART, C4, and various MDL and Bayesian variations. The package includes routines for experiment control, interactive operation, and analysis of tree building. The manual introduces the system and its many options, gives a basic review of tree learning, contains a guide to the literature and a glossary, and lists the manual pages for the routines and instructions on installation.

Software engineering and data management for automated payload experiment tool

NASA Technical Reports Server (NTRS)

Maddux, Gary A.; Provancha, Anna; Chattam, David

1994-01-01

The Microgravity Projects Office identified a need to develop a software package that will lead experiment developers through the development planning process, obtain necessary information, establish an electronic data exchange avenue, and allow easier manipulation/reformatting of the collected information. An MS-DOS compatible software package called the Automated Payload Experiment Tool (APET) has been developed and delivered. The objective of this task is to expand on the results of the APET work previously performed by University of Alabama in Huntsville (UAH) and provide versions of the software in a Macintosh and Windows compatible format. Appendix 1 science requirements document (SRD) Users Manual is attached.

Experience the Moon

NASA Astrophysics Data System (ADS)

Ortiz-Gil, A.; Benacchio, L.; Boccato, C.

2011-10-01

The Moon is, together with the Sun, the very first astronomical object that we experience in our life. As this is an exclusively visual experience, people with visual impairments need a different mode to experience it too. This statement is especially true when events, such as more and more frequent public observations of sky, take place. This is the reason why we are preparing a special package for visual impaired people containing three brand new items: 1. a tactile 3D Moon sphere in Braille with its paper key in Braille. To produce it we used imaging data obtained by NASA's mission Clementine, along with free image processing and 3D rendering software. In order to build the 3D small scale model funding by Europlanet and the Italian Ministry for Research have been used. 2. a multilingual web site for visually impaired users of all ages, on basic astronomy together with an indepth box about the Moon; 3. a book in Braille with the same content of the Web site mentioned above. All the items will be developed with the collaboration of visually impaired people that will check each step of the project and support their comments and criticism to improve it. We are going to test this package during the next International Observe the Moon Night event. After a first testing phase we'll collect all the feedback data in order to give an effective form to the package. Finally the Moon package could be delivered to all those who will demand it for outreach or educational goals.

Retail colour stability of lamb meat is influenced by breed type, muscle, packaging and iron concentration.

PubMed

Warner, R D; Kearney, G; Hopkins, D L; Jacob, R H

2017-07-01

The longissmus lumborum (LL) and semimembranosus (SM) muscles from 391 lamb carcasses, derived from various breed types, were used to investigate the effect of animal/muscle factors, packaging type [over-wrap (OW) or high oxygen modified atmosphere packaging (MAP O2 )] and duration of display on redness of meat during simulated retail display. Using statistical models the time required (in days) for redness to reach a threshold value of 3.5 (below this is unacceptable) was predicted. High levels of iron in the SM, but not LL, reduced the time for redness to reach 3.5 by 2-2.6days in MAP O2 and 0.5-0.8days in OW. The greater the proportion of Merino breed type, the shorter was the time for redness to reach the value of 3.5, an effect consistent across muscles and packaging types. In summary, breed type, packaging format, muscle and muscle iron levels had a significant impact on colour stability of sheep meat in oxygen-available packaging systems. Copyright © 2017. Published by Elsevier Ltd.

A packaged, low-cost, robust optical fiber strain sensor based on small cladding fiber sandwiched within periodic polymer grating.

PubMed

Chiang, Chia-Chin; Li, Chein-Hsing

2014-06-02

In the present study, a novel packaged long-period fiber grating (PLPFG) strain sensor is first presented. The MEMS process was utilized to fabricate the packaged optical fiber strain sensor. The sensor structure consisted of etched optical fiber sandwiched between two layers of thick photoresist SU-8 3050 and then packaged with poly (dimethylsiloxane) (PDMS) polymer material to construct the PLPFG strain sensor. The PDMS packaging material was used to prevent the glue effect, wherein glue flows into the LPFG structure and reduces coupling strength, in the surface bonding process. Because the fiber grating was packaged with PDMS material, it was effectively protected and made robust. The resonance attenuation dip of PLPFG grows when it is loading. This study explored the size effect of the grating period and fiber diameter of PLPFG via tensile testing. The experimental results found that the best strain sensitivity of the PLPFG strain sensor was -0.0342 dB/με, and that an R2 value of 0.963 was reached.

Quantarctica: A Unique, Open, Standalone GIS Package for Antarctic Research and Education

NASA Astrophysics Data System (ADS)

Roth, G.; Matsuoka, K.; Skoglund, A.; Melvaer, Y.; Tronstad, S.

2016-12-01

The Norwegian Polar Institute has developed Quantarctica, an open GIS package for use by the international Antarctic community. Quantarctica includes a wide range of cartographic basemap layers, geophysical and glaciological datasets, and satellite imagery in standardized file formats with a consistent Antarctic map projection and customized layer and labeling styles for quick, effective cartography. Quantarctica's strengths as an open science platform lie in 1) The complete, ready-to-use data package which includes full-resolution, original-quality vector and raster data, 2) A policy for freely-redistributable and modifiable data including all metadata and citations, and 3) QGIS, a free, full-featured, modular, offline-capable open-source GIS suite with a rapid and active development and support community. The Quantarctica team is actively seeking new contributions of peer-reviewed, freely distributable pan-Antarctic geospatial datasets for the next version release in 2017. As part of this ongoing development, we are investigating the best approaches for quickly and seamlessly distributing new and updated data to users, storing datasets in efficient file formats while maintaining full quality, and coexisting with numerous online data portals in a way that most actively benefits the Antarctic community. A recent survey of Quantarctica users showed broad geographical adoption among Antarctic Treaty countries, including those outside the large US and UK Antarctic programs. Maps and figures produced by Quantarctica have also appeared in open-access journals and outside of the formal scientific community on popular science and GIS blogs. Our experience with the Quantarctica project has shown the tremendous value of education and outreach, not only in promoting open software, data formats, and practices, but in empowering Antarctic science groups to more effectively use GIS and geospatial data. Open practices are making a huge impact in Antarctic GIS, where individual countries have historically maintained their own restricted Antarctic geodatabases and where a majority of the next generation of scientists are entering the field with experience in using geospatial thinking for planning, visualization, and problem solving.

Cluster Ion Spectrometry (CIS) Data Archiving in the CAA

NASA Astrophysics Data System (ADS)

Dandouras, I. S.; Barthe, A.; Penou, E.; Brunato, S.; Reme, H.; Kistler, L. M.; Blagau, A.; Facsko, G.; Kronberg, E.; Laakso, H. E.

2009-12-01

The Cluster Active Archive (CAA) aims at preserving the four Cluster spacecraft data, so that they are usable in the long-term by the scientific community as well as by the instrument team PIs and Co-Is. This implies that the data are filed together with the descriptive and documentary elements making it possible to select and interpret them. The CIS (Cluster Ion Spectrometry) experiment is a comprehensive ionic plasma spectrometry package onboard the four Cluster spacecraft, capable of obtaining full three-dimensional ion distributions (about 0 to 40 keV/e) with a time resolution of one spacecraft spin (4 sec) and with mass-per-charge composition determination. The CIS package consists of two different instruments, a Hot Ion Analyser (HIA) and a time-of-flight ion Composition Distribution Function (CODIF) analyser. For the archival of the CIS data a multi-level approach has been adopted. The CAA archival includes processed raw data (Level 1 data), moments of the ion distribution functions (Level 2 data), and calibrated high-resolution data in a variety of physical units (Level 3 data). The latter are 3-D ion distribution functions and 2-D pitch-angle distributions. In addition, a software package has been developed to allow the CAA user to interactively calculate partial or total moments of the ion distributions. Instrument cross-calibration has been an important activity in preparing the data for archival. The CIS data archive includes also experiment documentation, graphical products for browsing through the data, and data caveats. In addition, data quality indexes are under preparation, to help the user. Given the complexity of an ion spectrometer, and the variety of its operational modes, each one being optimised for a different magnetospheric region or measurement objective, consultation of the data caveats by the end user will always be a necessary step in the data analysis.

Apollo experience report: Apollo lunar surface experiments package data processing system

NASA Technical Reports Server (NTRS)

Eason, R. L.

1974-01-01

Apollo Program experience in the processing of scientific data from the Apollo lunar surface experiments package, in which computers and associated hardware and software were used, is summarized. The facility developed for the preprocessing of the lunar science data is described, as are several computer facilities and programs used by the Principal Investigators. The handling, processing, and analyzing of lunar science data and the interface with the Principal Investigators are discussed. Pertinent problems that arose in the development of the data processing schemes are discussed so that future programs may benefit from the solutions to the problems. The evolution of the data processing techniques for lunar science data related to recommendations for future programs of this type.

ParallelStructure: A R Package to Distribute Parallel Runs of the Population Genetics Program STRUCTURE on Multi-Core Computers

PubMed Central

Besnier, Francois; Glover, Kevin A.

2013-01-01

This software package provides an R-based framework to make use of multi-core computers when running analyses in the population genetics program STRUCTURE. It is especially addressed to those users of STRUCTURE dealing with numerous and repeated data analyses, and who could take advantage of an efficient script to automatically distribute STRUCTURE jobs among multiple processors. It also consists of additional functions to divide analyses among combinations of populations within a single data set without the need to manually produce multiple projects, as it is currently the case in STRUCTURE. The package consists of two main functions: MPI_structure() and parallel_structure() as well as an example data file. We compared the performance in computing time for this example data on two computer architectures and showed that the use of the present functions can result in several-fold improvements in terms of computation time. ParallelStructure is freely available at https://r-forge.r-project.org/projects/parallstructure/. PMID:23923012

msgbsR: An R package for analysing methylation-sensitive restriction enzyme sequencing data.

PubMed

Mayne, Benjamin T; Leemaqz, Shalem Y; Buckberry, Sam; Rodriguez Lopez, Carlos M; Roberts, Claire T; Bianco-Miotto, Tina; Breen, James

2018-02-01

Genotyping-by-sequencing (GBS) or restriction-site associated DNA marker sequencing (RAD-seq) is a practical and cost-effective method for analysing large genomes from high diversity species. This method of sequencing, coupled with methylation-sensitive enzymes (often referred to as methylation-sensitive restriction enzyme sequencing or MRE-seq), is an effective tool to study DNA methylation in parts of the genome that are inaccessible in other sequencing techniques or are not annotated in microarray technologies. Current software tools do not fulfil all methylation-sensitive restriction sequencing assays for determining differences in DNA methylation between samples. To fill this computational need, we present msgbsR, an R package that contains tools for the analysis of methylation-sensitive restriction enzyme sequencing experiments. msgbsR can be used to identify and quantify read counts at methylated sites directly from alignment files (BAM files) and enables verification of restriction enzyme cut sites with the correct recognition sequence of the individual enzyme. In addition, msgbsR assesses DNA methylation based on read coverage, similar to RNA sequencing experiments, rather than methylation proportion and is a useful tool in analysing differential methylation on large populations. The package is fully documented and available freely online as a Bioconductor package ( https://bioconductor.org/packages/release/bioc/html/msgbsR.html ).

Mechanical Designs and Developement of Advanced ACT: A Transfomative Upgrade to the ACTPol Receiver on the Atacama Cosmology Telescope.

NASA Astrophysics Data System (ADS)

Ward, Jonathan; Advanced ACT Collaboration, NASA Space Technology Research Fellowship

2017-06-01

The Atacama Cosmology Telescope is a six-meter diameter telescope located at 17,000 feet (5,200 meters) on Cerro Toco in the Andes Mountains of northern Chile. The next generation Advanced ACT (AdvACT) experiment is currently underway and will consist of three multichroic TES bolometer arrays operating together, totaling 5800 detectors on the sky. Each array will be sensitive to two frequency bands: a high frequency (HF) array at 150 and 230 GHz, two middle frequency (MF) arrays at 90 and 150 GHz, and a low frequency (LF) array at 28 and 41 GHz. The AdACT detector arrays will feature a revamped design when compared to ACTPol, including a transition to 150mm wafers equipped with multichroic pixels, allowing for a more densely packed focal plane. Each set of detectors consists of a feedhorn array of stacked silicon wafers which form a corrugated profile leading to each pixel. This is then followed by a four-piece detector stack assembly of silicon wafers which includes a waveguide interface plate, detector wafer, backshort cavity plate, and backshort cap. Each array is housed in a custom designed structure manufactured out of gold-plated, high purity copper. In addition to the detector array assembly, the array package also encloses the majority of our readout electronics. We present the full mechanical design of the AdvACT HF and MF detector array packages along with a detailed look at the detector array assemblies. We also highlight the use of continuously rotating warm half-wave plates (HWPs) at the front of the AdvACT receiver. We review the design of the rotation system and also early pipeline data analysis results. This experiment will also make use of extensive hardware and software previously developed for ACT, which will be modified to incorporate the new AdvACT instruments. Therefore, we discuss the integration of all AdvACT instruments with pre-existing ACTPol infrastructure.

ReadqPCR and NormqPCR: R packages for the reading, quality checking and normalisation of RT-qPCR quantification cycle (Cq) data

PubMed Central

2012-01-01

Background Measuring gene transcription using real-time reverse transcription polymerase chain reaction (RT-qPCR) technology is a mainstay of molecular biology. Technologies now exist to measure the abundance of many transcripts in parallel. The selection of the optimal reference gene for the normalisation of this data is a recurring problem, and several algorithms have been developed in order to solve it. So far nothing in R exists to unite these methods, together with other functions to read in and normalise the data using the chosen reference gene(s). Results We have developed two R/Bioconductor packages, ReadqPCR and NormqPCR, intended for a user with some experience with high-throughput data analysis using R, who wishes to use R to analyse RT-qPCR data. We illustrate their potential use in a workflow analysing a generic RT-qPCR experiment, and apply this to a real dataset. Packages are available from http://www.bioconductor.org/packages/release/bioc/html/ReadqPCR.htmland http://www.bioconductor.org/packages/release/bioc/html/NormqPCR.html Conclusions These packages increase the repetoire of RT-qPCR analysis tools available to the R user and allow them to (amongst other things) read their data into R, hold it in an ExpressionSet compatible R object, choose appropriate reference genes, normalise the data and look for differential expression between samples. PMID:22748112

Verification of shielding effect by the water-filled materials for space radiation in the International Space Station using passive dosimeters

NASA Astrophysics Data System (ADS)

Kodaira, S.; Tolochek, R. V.; Ambrozova, I.; Kawashima, H.; Yasuda, N.; Kurano, M.; Kitamura, H.; Uchihori, Y.; Kobayashi, I.; Hakamada, H.; Suzuki, A.; Kartsev, I. S.; Yarmanova, E. N.; Nikolaev, I. V.; Shurshakov, V. A.

2014-01-01

The dose reduction effects for space radiation by installation of water shielding material ("protective curtain") of a stack board consisting of the hygienic wipes and towels have been experimentally evaluated in the International Space Station by using passive dosimeters. The averaged water thickness of the protective curtain was 6.3 g/cm2. The passive dosimeters consisted of a combination of thermoluminescent detectors (TLDs) and plastic nuclear track detectors (PNTDs). Totally 12 passive dosimeter packages were installed in the Russian Service Module during late 2010. Half of the packages were located at the protective curtain surface and the other half were at the crew cabin wall behind or aside the protective curtain. The mean absorbed dose and dose equivalent rates are measured to be 327 μGy/day and 821 μSv/day for the unprotected packages and 224 μGy/day and 575 μSv/day for the protected packages, respectively. The observed dose reduction rate with protective curtain was found to be 37 ± 7% in dose equivalent, which was consistent with the calculation in the spherical water phantom by PHITS. The contributions due to low and high LET particles were found to be comparable in observed dose reduction rate. The protective curtain would be effective shielding material for not only trapped particles (several 10 MeV) but also for low energy galactic cosmic rays (several 100 MeV/n). The properly utilized protective curtain will effectively reduce the radiation dose for crew living in space station and prolong long-term mission in the future.

GENERAL PURPOSE ADA PACKAGES

NASA Technical Reports Server (NTRS)

Klumpp, A. R.

1994-01-01

Ten families of subprograms are bundled together for the General-Purpose Ada Packages. The families bring to Ada many features from HAL/S, PL/I, FORTRAN, and other languages. These families are: string subprograms (INDEX, TRIM, LOAD, etc.); scalar subprograms (MAX, MIN, REM, etc.); array subprograms (MAX, MIN, PROD, SUM, GET, and PUT); numerical subprograms (EXP, CUBIC, etc.); service subprograms (DATE_TIME function, etc.); Linear Algebra II; Runge-Kutta integrators; and three text I/O families of packages. In two cases, a family consists of a single non-generic package. In all other cases, a family comprises a generic package and its instances for a selected group of scalar types. All generic packages are designed to be easily instantiated for the types declared in the user facility. The linear algebra package is LINRAG2. This package includes subprograms supplementing those in NPO-17985, An Ada Linear Algebra Package Modeled After HAL/S (LINRAG). Please note that LINRAG2 cannot be compiled without LINRAG. Most packages have widespread applicability, although some are oriented for avionics applications. All are designed to facilitate writing new software in Ada. Several of the packages use conventions introduced by other programming languages. A package of string subprograms is based on HAL/S (a language designed for the avionics software in the Space Shuttle) and PL/I. Packages of scalar and array subprograms are taken from HAL/S or generalized current Ada subprograms. A package of Runge-Kutta integrators is patterned after a built-in MAC (MIT Algebraic Compiler) integrator. Those packages modeled after HAL/S make it easy to translate existing HAL/S software to Ada. The General-Purpose Ada Packages program source code is available on two 360K 5.25" MS-DOS format diskettes. The software was developed using VAX Ada v1.5 under DEC VMS v4.5. It should be portable to any validated Ada compiler and it should execute either interactively or in batch. The largest package requires 205K of main memory on a DEC VAX running VMS. The software was developed in 1989, and is a copyrighted work with all copyright vested in NASA.

Packaging Technologies for 500 C SiC Electronics and Sensors: Challenges in Material Science and Technology

NASA Technical Reports Server (NTRS)

Chen, Liang-Yu; Neudeck, Philip G.; Behelm, Glenn M.; Spry, David J.; Meredith, Roger D.; Hunter, Gary W.

2015-01-01

This paper presents ceramic substrates and thick-film metallization based packaging technologies in development for 500C silicon carbide (SiC) electronics and sensors. Prototype high temperature ceramic chip-level packages and printed circuit boards (PCBs) based on ceramic substrates of aluminum oxide (Al2O3) and aluminum nitride (AlN) have been designed and fabricated. These ceramic substrate-based chip-level packages with gold (Au) thick-film metallization have been electrically characterized at temperatures up to 550C. The 96 alumina packaging system composed of chip-level packages and PCBs has been successfully tested with high temperature SiC discrete transistor devices at 500C for over 10,000 hours. In addition to tests in a laboratory environment, a SiC junction field-effect-transistor (JFET) with a packaging system composed of a 96 alumina chip-level package and an alumina printed circuit board was tested on low earth orbit for eighteen months via a NASA International Space Station experiment. In addition to packaging systems for electronics, a spark-plug type sensor package based on this high temperature interconnection system for high temperature SiC capacitive pressure sensors was also developed and tested. In order to further significantly improve the performance of packaging system for higher packaging density, higher operation frequency, power rating, and even higher temperatures, some fundamental material challenges must be addressed. This presentation will discuss previous development and some of the challenges in material science (technology) to improve high temperature dielectrics for packaging applications.

Tobacco packaging design for reducing tobacco use.

PubMed

McNeill, Ann; Gravely, Shannon; Hitchman, Sara C; Bauld, Linda; Hammond, David; Hartmann-Boyce, Jamie

2017-04-27

Tobacco use is the largest single preventable cause of death and disease worldwide. Standardised tobacco packaging is an intervention intended to reduce the promotional appeal of packs and can be defined as packaging with a uniform colour (and in some cases shape and size) with no logos or branding, apart from health warnings and other government-mandated information, and the brand name in a prescribed uniform font, colour and size. Australia was the first country to implement standardised tobacco packaging between October and December 2012, France implemented standardised tobacco packaging on 1 January 2017 and several other countries are implementing, or intending to implement, standardised tobacco packaging. To assess the effect of standardised tobacco packaging on tobacco use uptake, cessation and reduction. We searched MEDLINE, Embase, PsycINFO and six other databases from 1980 to January 2016. We checked bibliographies and contacted study authors to identify additional peer-reviewed studies. Primary outcomes included changes in tobacco use prevalence incorporating tobacco use uptake, cessation, consumption and relapse prevention. Secondary outcomes covered intermediate outcomes that can be measured and are relevant to tobacco use uptake, cessation or reduction. We considered multiple study designs: randomised controlled trials, quasi-experimental and experimental studies, observational cross-sectional and cohort studies. The review focused on all populations and people of any age; to be included, studies had to be published in peer-reviewed journals. We examined studies that assessed the impact of changes in tobacco packaging such as colour, design, size and type of health warnings on the packs in relation to branded packaging. In experiments, the control condition was branded tobacco packaging but could include variations of standardised packaging. Screening and data extraction followed standard Cochrane methods. We used different 'Risk of bias' domains for different study types. We have summarised findings narratively. Fifty-one studies met our inclusion criteria, involving approximately 800,000 participants. The studies included were diverse, including observational studies, between- and within-participant experimental studies, cohort and cross-sectional studies, and time-series analyses. Few studies assessed behavioural outcomes in youth and non-smokers. Five studies assessed the primary outcomes: one observational study assessed smoking prevalence among 700,000 participants until one year after standardised packaging in Australia; four studies assessed consumption in 9394 participants, including a series of Australian national cross-sectional surveys of 8811 current smokers, in addition to three smaller studies. No studies assessed uptake, cessation, or relapse prevention. Two studies assessed quit attempts. Twenty studies examined other behavioural outcomes and 45 studies examined non-behavioural outcomes (e.g. appeal, perceptions of harm). In line with the challenges inherent in evaluating standardised tobacco packaging, a number of methodological imitations were apparent in the included studies and overall we judged most studies to be at high or unclear risk of bias in at least one domain. The one included study assessing the impact of standardised tobacco packaging on smoking prevalence in Australia found a 3.7% reduction in odds when comparing before to after the packaging change, or a 0.5 percentage point drop in smoking prevalence, when adjusting for confounders. Confidence in this finding is limited, due to the nature of the evidence available, and is therefore rated low by GRADE standards. Findings were mixed amongst the four studies assessing consumption, with some studies finding no difference and some studies finding evidence of a decrease; certainty in this outcome was rated very low by GRADE standards due to the limitations in study design. One national study of Australian adult smoker cohorts (5441 participants) found that quit attempts increased from 20.2% prior to the introduction of standardised packaging to 26.6% one year post-implementation. A second study of calls to quitlines provides indirect support for this finding, with a 78% increase observed in the number of calls after the implementation of standardised packaging. Here again, certainty is low. Studies of other behavioural outcomes found evidence of increased avoidance behaviours when using standardised packs, reduced demand for standardised packs and reduced craving. Evidence from studies measuring eye-tracking showed increased visual attention to health warnings on standardised compared to branded packs. Corroborative evidence for the latter finding came from studies assessing non-behavioural outcomes, which in general found greater warning salience when viewing standardised, than branded packs. There was mixed evidence for quitting cognitions, whereas findings with youth generally pointed towards standardised packs being less likely to motivate smoking initiation than branded packs. We found the most consistent evidence for appeal, with standardised packs rating lower than branded packs. Tobacco in standardised packs was also generally perceived as worse-tasting and lower quality than tobacco in branded packs. Standardised packaging also appeared to reduce misperceptions that some cigarettes are less harmful than others, but only when dark colours were used for the uniform colour of the pack. The available evidence suggests that standardised packaging may reduce smoking prevalence. Only one country had implemented standardised packaging at the time of this review, so evidence comes from one large observational study that provides evidence for this effect. A reduction in smoking behaviour is supported by routinely collected data by the Australian government. Data on the effects of standardised packaging on non-behavioural outcomes (e.g. appeal) are clearer and provide plausible mechanisms of effect consistent with the observed decline in prevalence. As standardised packaging is implemented in different countries, research programmes should be initiated to capture long term effects on tobacco use prevalence, behaviour, and uptake. We did not find any evidence suggesting standardised packaging may increase tobacco use.

Web-based, GPU-accelerated, Monte Carlo simulation and visualization of indirect radiation imaging detector performance.

PubMed

Dong, Han; Sharma, Diksha; Badano, Aldo

2014-12-01

Monte Carlo simulations play a vital role in the understanding of the fundamental limitations, design, and optimization of existing and emerging medical imaging systems. Efforts in this area have resulted in the development of a wide variety of open-source software packages. One such package, hybridmantis, uses a novel hybrid concept to model indirect scintillator detectors by balancing the computational load using dual CPU and graphics processing unit (GPU) processors, obtaining computational efficiency with reasonable accuracy. In this work, the authors describe two open-source visualization interfaces, webmantis and visualmantis to facilitate the setup of computational experiments via hybridmantis. The visualization tools visualmantis and webmantis enable the user to control simulation properties through a user interface. In the case of webmantis, control via a web browser allows access through mobile devices such as smartphones or tablets. webmantis acts as a server back-end and communicates with an NVIDIA GPU computing cluster that can support multiuser environments where users can execute different experiments in parallel. The output consists of point response and pulse-height spectrum, and optical transport statistics generated by hybridmantis. The users can download the output images and statistics through a zip file for future reference. In addition, webmantis provides a visualization window that displays a few selected optical photon path as they get transported through the detector columns and allows the user to trace the history of the optical photons. The visualization tools visualmantis and webmantis provide features such as on the fly generation of pulse-height spectra and response functions for microcolumnar x-ray imagers while allowing users to save simulation parameters and results from prior experiments. The graphical interfaces simplify the simulation setup and allow the user to go directly from specifying input parameters to receiving visual feedback for the model predictions.

Theoretical and Experimental Beam Plasma Physics (TEBPP)

NASA Technical Reports Server (NTRS)

Roberts, W. T.

1985-01-01

The theoretical and experimental beam plasma physics (TEBPP) consists of a package of five instruments to measure electric and magnetic fields, plasma density and temperature, neutral density, photometric emissions, and energetic particle spectra during firings of the particle injector (SEPAC) electron beam. The package is deployed on a maneuverable boom (or RMS) and is used to measure beam characteristics and induced perturbations in the near field ( 10 m) and mid field (10 m to 100 m) along the electron beam. The TEBPP package will be designed to investigate induced oscillations and induced electromagnetic mode waves, neutral and ion density and temperature effects, and beam characteristics as a function of axial distance.

Theoretical and Experimental Beam Plasma Physics (TEBPP)

NASA Technical Reports Server (NTRS)

Roberts, B.

1986-01-01

The theoretical and experimental beam plasma physics (TEBPP) consists of a package of five instruments to measure electric and magnetic fields, plasma density and temperature, neutral density, photometric emissions, and energetic particle spectra during firings of the particle injector (SEPAC) electron beam. The package is developed on a maneuverable boom (or RMS) and is used to measure beam characteristics and induced perturbations field ( 10 m) and mid field ( 10 m to 100 m) along the electron beam. The TEBPP package will be designed to investigate induced oscillations and induced electromagnetic mode waves, neutral and ion density and temperature effects, and beam characteristics as a function of axial distance.

Moisture Content of Commercial Items Used in the MRE

DTIC Science & Technology

2004-06-01

5.4.1.2 Shortbread Cookies The Shortbread Cookies are packaged 6 each in a metallized, co- extruded , oriented-polypropylene package (vending machine...specific condition. The products consisted of a vegetable cracker, an oatmeal cookie, a shortbread cookie and a cheese filled pretzel snack . Each sample...shortbread cookie 4. Cheese Combos pretzel snack Five Sessions (testing occurred during the period of March-September 2003): Control vs. storage

System design package for SIMS prototype system 4, solar heating and domestic hot water

NASA Technical Reports Server (NTRS)

1978-01-01

The system consisted of a modular designed prepackaged solar unit, containing solar collectors, a rock storage container, blowers, dampers, ducting, air-to-water heat exchanger, DHW preheat tank, piping, and system controls. The system was designed to be installed adjacent to a small single family dwelling. The description, performance specification, subsystem drawings, verification plan/procedure, and hazard analysis of the system were packaged for evaluation.

Advanced Simulation in Undergraduate Pilot Training: Automatic Instructional System

DTIC Science & Technology

1975-10-01

an addressable reel-to--reel audio tape recorder, a random access audio memory drum , and an interactive software package which permits the user to...audio memory drum , and an interactive software package which permits the user to develop preptogtahmed exercises. Figure 2 illustrates overall...Data Recprding System consists of two elements; an overlay program which performs the real-time sampling of specified variables and stores data to disc

Selecting the best bank that offered Islamic personal loan package by using consistent fuzzy preference relations (CFPR)

NASA Astrophysics Data System (ADS)

Kadir, Norhidayah A.; Sarudin, Ezzah Suraya; Hamid, Fairus; Shamsuddin, Nor Diyana Ahmad

2014-10-01

There are various thoughts and opinions when it comes to how people think of their selected banks. Therefore, to choose the best bank with a good personal loan package can be a bit tricky especially for first time customer. This research offers a guide in choosing the right bank for applying personal loan package by highlighting the important criteria that applicants should take into consideration. In order to cater the problem above, we used Consistent Fuzzy Preference Relations (CFPR). Based on expert and public opinions, the important criteria in selecting an Islamic personal loan package are interest rate, tenure of loan, processing period and security of the loan. We developed questionnaire with the criteria mention earlier and distributed it among academic staffs and non academic staffs at Faculty of Computer and Mathematical Sciences (FSKM), UiTM Shah Alam. Based on the questionnaire, we found that four banks have been selected for multiple reasons. Before we could determine the best bank, calculations are divided into 2 phases which are criteria weights determination and ranking of alternatives. We implemented these phases to get the aggregation result and to obtain the ranking in descending order. As a result, our objectives have been achieved. As a conclusion, CFPR can help others in the decision making process.

Safety. A Guide for Industrial Cooperative Training Programs. Learning Activity Package. LAP 6.

ERIC Educational Resources Information Center

Duenk, Lester G.; Lear, George

This learning activity package, one of six intended for use in Industrial Cooperative Training Programs, is designed to provide students with information on several general safety topics which would apply in most employment situations. (The industrial cooperative training program provides industrial occupational training experience for high school…

XDesign: an open-source software package for designing X-ray imaging phantoms and experiments.

PubMed

Ching, Daniel J; Gürsoy, Dogˇa

2017-03-01

The development of new methods or utilization of current X-ray computed tomography methods is impeded by the substantial amount of expertise required to design an X-ray computed tomography experiment from beginning to end. In an attempt to make material models, data acquisition schemes and reconstruction algorithms more accessible to researchers lacking expertise in some of these areas, a software package is described here which can generate complex simulated phantoms and quantitatively evaluate new or existing data acquisition schemes and image reconstruction algorithms for targeted applications.

XDesign: An open-source software package for designing X-ray imaging phantoms and experiments

DOE PAGES

Ching, Daniel J.; Gursoy, Dogˇa

2017-02-21

Here, the development of new methods or utilization of current X-ray computed tomography methods is impeded by the substantial amount of expertise required to design an X-ray computed tomography experiment from beginning to end. In an attempt to make material models, data acquisition schemes and reconstruction algorithms more accessible to researchers lacking expertise in some of these areas, a software package is described here which can generate complex simulated phantoms and quantitatively evaluate new or existing data acquisition schemes and image reconstruction algorithms for targeted applications.

Attitude sensor package

NASA Technical Reports Server (NTRS)

Aceti, R.; Trischberger, M.; Underwood, P. J.; Pomilia, A.; Cosi, M.; Boldrini, F.

1993-01-01

This paper describes the design, construction, testing, and successful flight of the Attitude Sensor Package. The payload was assembled on a standard HITCHHIKER experiment mounting plate, and made extensive use of the carrier's power and data handling capabilities. The side mounted HITCHHIKER version was chosen, since this configuration provided the best viewing conditions for the instruments. The combustion was successfully flown on board Space Shuttle Columbia (STS-52), in October 1992. The payload was one of the 14 experiments of the In-Orbit Technology Demonstration Program (Phase 1) of the European Space Agency.

First-Time Analysis of Completely Restored DTREM Instrument Data from Apollo 14 and 15

NASA Technical Reports Server (NTRS)

McBride, Marie J.; Williams, David R.; Hills, H. Kent; Turner, Niescja

2013-01-01

The Dust, Thermal and Radiation Engineering Measurement (DTREM) packages (figure 1) mounted on the central stations of the Apollo 11, 12, 14, and 15 ALSEPs (Apollo Lunar Surface Experiments Packages) measured the outputs of exposed solar cells and thermistors over time. The goal of the experiment, also commonly known as the dust detector, was to study the long-term effects of dust, radiation, and temperature at the lunar surface on solar cells. The monitors returned data for up to almost 8 years from the lunar surface.

Structure and function of the small terminase component of the DNA packaging machine in T4-like bacteriophages

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sun, Siyang; Gao, Song; Kondabagil, Kiran

2012-04-04

Tailed DNA bacteriophages assemble empty procapsids that are subsequently filled with the viral genome by means of a DNA packaging machine situated at a special fivefold vertex. The packaging machine consists of a 'small terminase' and a 'large terminase' component. One of the functions of the small terminase is to initiate packaging of the viral genome, whereas the large terminase is responsible for the ATP-powered translocation of DNA. The small terminase subunit has three domains, an N-terminal DNA-binding domain, a central oligomerization domain, and a C-terminal domain for interacting with the large terminase. Here we report structures of the centralmore » domain in two different oligomerization states for a small terminase from the T4 family of phages. In addition, we report biochemical studies that establish the function for each of the small terminase domains. On the basis of the structural and biochemical information, we propose a model for DNA packaging initiation.« less

Variational Trajectory Optimization Tool Set: Technical description and user's manual

NASA Technical Reports Server (NTRS)

Bless, Robert R.; Queen, Eric M.; Cavanaugh, Michael D.; Wetzel, Todd A.; Moerder, Daniel D.

1993-01-01

The algorithms that comprise the Variational Trajectory Optimization Tool Set (VTOTS) package are briefly described. The VTOTS is a software package for solving nonlinear constrained optimal control problems from a wide range of engineering and scientific disciplines. The VTOTS package was specifically designed to minimize the amount of user programming; in fact, for problems that may be expressed in terms of analytical functions, the user needs only to define the problem in terms of symbolic variables. This version of the VTOTS does not support tabular data; thus, problems must be expressed in terms of analytical functions. The VTOTS package consists of two methods for solving nonlinear optimal control problems: a time-domain finite-element algorithm and a multiple shooting algorithm. These two algorithms, under the VTOTS package, may be run independently or jointly. The finite-element algorithm generates approximate solutions, whereas the shooting algorithm provides a more accurate solution to the optimization problem. A user's manual, some examples with results, and a brief description of the individual subroutines are included.

Experimental Approaches to Study Genome Packaging of Influenza A Viruses.

PubMed

Isel, Catherine; Munier, Sandie; Naffakh, Nadia

2016-08-09

The genome of influenza A viruses (IAV) consists of eight single-stranded negative sense viral RNAs (vRNAs) encapsidated into viral ribonucleoproteins (vRNPs). It is now well established that genome packaging (i.e., the incorporation of a set of eight distinct vRNPs into budding viral particles), follows a specific pathway guided by segment-specific cis-acting packaging signals on each vRNA. However, the precise nature and function of the packaging signals, and the mechanisms underlying the assembly of vRNPs into sub-bundles in the cytoplasm and their selective packaging at the viral budding site, remain largely unknown. Here, we review the diverse and complementary methods currently being used to elucidate these aspects of the viral cycle. They range from conventional and competitive reverse genetics, single molecule imaging of vRNPs by fluorescence in situ hybridization (FISH) and high-resolution electron microscopy and tomography of budding viral particles, to solely in vitro approaches to investigate vRNA-vRNA interactions at the molecular level.

Effect of an active packaging with citrus extract on lipid oxidation and sensory quality of cooked turkey meat.

PubMed

Contini, Claudia; Álvarez, Rocío; O'Sullivan, Michael; Dowling, Denis P; Gargan, Sean Óg; Monahan, Frank J

2014-03-01

An antioxidant active packaging was prepared by coating a citrus extract, consisting of a mixture of carboxylic acids and flavanones, on polyethylene terephthalate trays. The effect of the packaging in reducing lipid oxidation in cooked turkey meat and on meat pH, colour characteristics and sensorial parameters was investigated. An untrained sensory panel evaluated the odour, taste, tenderness, juiciness and overall acceptability of the meat, using triangle, paired preference and quantitative response scale tests. A comparison between the antioxidant effects of the different components of the extract was also carried out. The packaging led to a significant reduction in lipid oxidation. After 2 days of refrigerated storage the sensory panel detected differences in odour and, after 4 days, rated the meat stored in the active packaging higher for tenderness and overall acceptability. Citric acid appeared to be the most important component of the extract with regard to its antioxidant potency. Copyright © 2013 Elsevier Ltd. All rights reserved.

Shelf life assessment of industrial durum wheat bread as a function of packaging system.

PubMed

Licciardello, Fabio; Giannone, Virgilio; Del Nobile, Matteo Alessandro; Muratore, Giuseppe; Summo, Carmine; Giarnetti, Mariagrazia; Caponio, Francesco; Paradiso, Vito Michele; Pasqualone, Antonella

2017-06-01

This study compared the effect of different packaging systems on industrial durum wheat bread shelf-life, with regard to thermoformed packaging (TF) and flow-packaging (FP). Two TFs having different thickness and one FP were compared by assessing physico-chemical and sensorial properties and volatile compounds of sliced bread during 90days of storage. Texture, a w and bread moisture varied according to a first-order kinetic model, with FP samples ageing faster than TFs. Sensorial features such as consistency, stale odor, and sour odor, increased their intensity during storage. Furans decreased, whereas hexanal increased. The Principal Component Analysis of the whole dataset pointed out that the TF system at reduced thickness could be adopted up to 60days, without compromising the standard commercial life of industrial bread and allowing to save packaging material. The FP system would allow further saving, but it should be preferred when the expected product turnover is within 30days. Copyright © 2016 Elsevier Ltd. All rights reserved.

A geometry package for generation of input data for a three-dimensional potential-flow program

NASA Technical Reports Server (NTRS)

Halsey, N. D.; Hess, J. L.

1978-01-01

The preparation of geometric data for input to three-dimensional potential flow programs was automated and simplified by a geometry package incorporated into the NASA Langley version of the 3-D lifting potential flow program. Input to the computer program for the geometry package consists of a very sparse set of coordinate data, often with an order of magnitude of fewer points than required for the actual potential flow calculations. Isolated components, such as wings, fuselages, etc. are paneled automatically, using one of several possible element distribution algorithms. Curves of intersection between components are calculated, using a hybrid curve-fit/surface-fit approach. Intersecting components are repaneled so that adjacent elements on either side of the intersection curves line up in a satisfactory manner for the potential-flow calculations. Many cases may be run completely (from input, through the geometry package, and through the flow calculations) without interruption. Use of the package significantly reduces the time and expense involved in making three-dimensional potential flow calculations.

Miniature spectrally selective dosimeter

NASA Technical Reports Server (NTRS)

Adams, R. R.; Macconochie, I. O.; Poole, B. D., Jr. (Inventor)

1980-01-01

A miniature spectrally selective dosimeter capable of measuring selected bandwidths of radiation exposure on small mobile areas is described. This is achieved by the combination of photovoltaic detectors, electrochemical integrators (E-cells) and filters in a small compact case which can be easily attached in close proximity to and substantially parallel to the surface being measured. In one embodiment two photovoltaic detectors, two E-cells, and three filters are packaged in a small case with attaching means consisting of a safety pin. In another embodiment, two detectors, one E-cell, three filters are packaged in a small case with attaching means consisting of a clip to clip over a side piece of an eye glass frame.

Calibration of the aerodynamic coefficient identification package measurements from the shuttle entry flights using inertial measurement unit data

NASA Technical Reports Server (NTRS)

Heck, M. L.; Findlay, J. T.; Compton, H. R.

1983-01-01

The Aerodynamic Coefficient Identification Package (ACIP) is an instrument consisting of body mounted linear accelerometers, rate gyros, and angular accelerometers for measuring the Space Shuttle vehicular dynamics. The high rate recorded data are utilized for postflight aerodynamic coefficient extraction studies. Although consistent with pre-mission accuracies specified by the manufacturer, the ACIP data were found to contain detectable levels of systematic error, primarily bias, as well as scale factor, static misalignment, and temperature dependent errors. This paper summarizes the technique whereby the systematic ACIP error sources were detected, identified, and calibrated with the use of recorded dynamic data from the low rate, highly accurate Inertial Measurement Units.

Warpage of QFN Package in Post Mold Cure Process of integrated circuit packaging

NASA Astrophysics Data System (ADS)

Sriwithoon, Nattha; Ugsornrat, Kessararat; Srisuwitthanon, Warayoot; Thonglor, Panakamon

2017-09-01

This research studied about warpage of QFN package in post mold cure process of integrated circuit (IC) packages using pre-plated (PPF) leadframe. For IC package, epoxy molding compound (EMC) are molded by cross linking of compound stiffness but incomplete crosslinked network and leading the fully cured thermoset by post mold cure (PMC) process. The cure temperature of PMC can change microstructure of EMC in term of stress inside the package and effect to warpage of the package due to coefficient of thermal expansion (CTE) between EMC and leadframe. In experiment, cure temperatures were varied to check the effect of internal stress due to different cure temperature after completed post mold cure for TDFN 2×3 8L. The cure temperature were varied with 180 °C, 170 °C, 160 °C, and 150°C with cure time 4 and 6 hours, respectively. For analysis, the TDFN 2×3 8L packages were analyzed the warpage by thickness gauge and scanning acoustic microscope (SAM) after take the test samples out from the oven cure. The results confirmed that effect of different CTE between EMC and leadframe due to different cure temperature resulting to warpage of the TDFN 2×3 8L packages.

Effects of illumination and packaging on non-heme iron and color attributes of sliced ham.

PubMed

Li, H; Li, C B; Xu, X L; Zhou, G H

2012-08-01

This study was designed to investigate effects of illumination and packaging on color of cooked cured sliced ham during refrigeration, and the possibility of decomposition of nitrosylheme under light and oxygen exposure. Three illumination levels and three packaging films with different oxygen transmission rates (OTRs) were used in two separate experiments during 35 days storage, and pH value, a* value, nitrosylheme, residual nitrite and non-heme iron were evaluated. Packaging OTRs had significant effects (P<0.01) on a* value, but illumination level and packaging OTR did not affect (P>0.05) nitrosylheme concentration during storage. For both groups, storage time had a significant effect (P<0.01) on a* value and nitrosylheme. Negative relationships between nitrosylheme and nitrite in the illumination group, and between nitrosylheme and non-heme iron in the packaging group were observed. Therefore, illumination level and packaging OTR had limited effects on overall pigment stability, but more discoloration and loss of redness occurred on the surface of products. Copyright © 2012 Elsevier Ltd. All rights reserved.

Mousetrap: An integrated, open-source mouse-tracking package.

PubMed

Kieslich, Pascal J; Henninger, Felix

2017-10-01

Mouse-tracking - the analysis of mouse movements in computerized experiments - is becoming increasingly popular in the cognitive sciences. Mouse movements are taken as an indicator of commitment to or conflict between choice options during the decision process. Using mouse-tracking, researchers have gained insight into the temporal development of cognitive processes across a growing number of psychological domains. In the current article, we present software that offers easy and convenient means of recording and analyzing mouse movements in computerized laboratory experiments. In particular, we introduce and demonstrate the mousetrap plugin that adds mouse-tracking to OpenSesame, a popular general-purpose graphical experiment builder. By integrating with this existing experimental software, mousetrap allows for the creation of mouse-tracking studies through a graphical interface, without requiring programming skills. Thus, researchers can benefit from the core features of a validated software package and the many extensions available for it (e.g., the integration with auxiliary hardware such as eye-tracking, or the support of interactive experiments). In addition, the recorded data can be imported directly into the statistical programming language R using the mousetrap package, which greatly facilitates analysis. Mousetrap is cross-platform, open-source and available free of charge from https://github.com/pascalkieslich/mousetrap-os .

PsyToolkit: a software package for programming psychological experiments using Linux.

PubMed

Stoet, Gijsbert

2010-11-01

PsyToolkit is a set of software tools for programming psychological experiments on Linux computers. Given that PsyToolkit is freely available under the Gnu Public License, open source, and designed such that it can easily be modified and extended for individual needs, it is suitable not only for technically oriented Linux users, but also for students, researchers on small budgets, and universities in developing countries. The software includes a high-level scripting language, a library for the programming language C, and a questionnaire presenter. The software easily integrates with other open source tools, such as the statistical software package R. PsyToolkit is designed to work with external hardware (including IoLab and Cedrus response keyboards and two common digital input/output boards) and to support millisecond timing precision. Four in-depth examples explain the basic functionality of PsyToolkit. Example 1 demonstrates a stimulus-response compatibility experiment. Example 2 demonstrates a novel mouse-controlled visual search experiment. Example 3 shows how to control light emitting diodes using PsyToolkit, and Example 4 shows how to build a light-detection sensor. The last two examples explain the electronic hardware setup such that they can even be used with other software packages.

Data assimilation and model evaluation experiment datasets

NASA Technical Reports Server (NTRS)

Lai, Chung-Cheng A.; Qian, Wen; Glenn, Scott M.

1994-01-01

The Institute for Naval Oceanography, in cooperation with Naval Research Laboratories and universities, executed the Data Assimilation and Model Evaluation Experiment (DAMEE) for the Gulf Stream region during fiscal years 1991-1993. Enormous effort has gone into the preparation of several high-quality and consistent datasets for model initialization and verification. This paper describes the preparation process, the temporal and spatial scopes, the contents, the structure, etc., of these datasets. The goal of DAMEE and the need of data for the four phases of experiment are briefly stated. The preparation of DAMEE datasets consisted of a series of processes: (1) collection of observational data; (2) analysis and interpretation; (3) interpolation using the Optimum Thermal Interpolation System package; (4) quality control and re-analysis; and (5) data archiving and software documentation. The data products from these processes included a time series of 3D fields of temperature and salinity, 2D fields of surface dynamic height and mixed-layer depth, analysis of the Gulf Stream and rings system, and bathythermograph profiles. To date, these are the most detailed and high-quality data for mesoscale ocean modeling, data assimilation, and forecasting research. Feedback from ocean modeling groups who tested this data was incorporated into its refinement. Suggestions for DAMEE data usages include (1) ocean modeling and data assimilation studies, (2) diagnosis and theoretical studies, and (3) comparisons with locally detailed observations.

Techniques to measure sorption and migration between small molecules and packaging. A critical review.

PubMed

Kadam, Ashish A; Karbowiak, Thomas; Voilley, Andrée; Debeaufort, Frédéric

2015-05-01

The mass transfer parameters diffusion and sorption in food and packaging or between them are the key parameters for assessing a food product's shelf-life in reference to consumer safety. This has become of paramount importance owing to the legislations set by the regulated markets. The technical capabilities that can be exploited for analyzing product-package interactions have been growing rapidly. Different techniques categorized according to the state of the diffusant (gas or liquid) in contact with the packaging material are emphasized in this review. Depending on the diffusant and on the analytical question under review, the different ways to study sorption and/or migration are presented and compared. Some examples have been suggested to reach the best possible choice, consisting of a single technique or a combination of different approaches. © 2014 Society of Chemical Industry.

Examination of shipping packages 9975-01658, 9975-02075 and 9975-02738

DOE Office of Scientific and Technical Information (OSTI.GOV)

Daugherty, W. L.

SRNL has assisted in the examination of three 9975 shipping packages (9975-01658, 9975-02075 and 9975-02738) following their use for storage of nuclear material in K-Area Complex (KAC). Each of these was targeted for examination because the axial gap exceeded the 1 inch maximum criterion, signaling the potential for degradation of the fiberboard overpack and drum. Each package experienced a degree of compaction of the bottom fiberboard layers, and had elevated moisture levels toward the bottom. A small amount of mold was observed on the lower fiberboard assembly in 9975-02738. However, the majority of the fiberboard in each package appeared tomore » retain good integrity consistent with non-degraded material. Minor corrosion was observed on these drums, but is judged to have not compromised the drum integrity.« less

The Influenza A Virus PB2, PA, NP, and M Segments Play a Pivotal Role during Genome Packaging

PubMed Central

Gao, Qinshan; Chou, Yi-Ying; Doğanay, Sultan; Vafabakhsh, Reza; Ha, Taekjip

2012-01-01

The genomes of influenza A viruses consist of eight negative-strand RNA segments. Recent studies suggest that influenza viruses are able to specifically package their segmented genomes into the progeny virions. Segment-specific packaging signals of influenza virus RNAs (vRNAs) are located in the 5′ and 3′ noncoding regions, as well as in the terminal regions, of the open reading frames. How these packaging signals function during genome packaging remains unclear. Previously, we generated a 7-segmented virus in which the hemagglutinin (HA) and neuraminidase (NA) segments of the influenza A/Puerto Rico/8/34 virus were replaced by a chimeric influenza C virus hemagglutinin/esterase/fusion (HEF) segment carrying the HA packaging sequences. The robust growth of the HEF virus suggested that the NA segment is not required for the packaging of other segments. In this study, in order to determine the roles of the other seven segments during influenza A virus genome assembly, we continued to use this HEF virus as a tool and analyzed the effects of replacing the packaging sequences of other segments with those of the NA segment. Our results showed that deleting the packaging signals of the PB1, HA, or NS segment had no effect on the growth of the HEF virus, while growth was greatly impaired when the packaging sequence of the PB2, PA, nucleoprotein (NP), or matrix (M) segment was removed. These results indicate that the PB2, PA, NP, and M segments play a more important role than the remaining four vRNAs during the genome-packaging process. PMID:22532680

Novel Techniques for Millimeter-Wave Packages

NASA Technical Reports Server (NTRS)

Herman, Martin I.; Lee, Karen A.; Kolawa, Elzbieta A.; Lowry, Lynn E.; Tulintseff, Ann N.

1995-01-01

A new millimeter-wave package architecture with supporting electrical, mechanical and material science experiment and analysis is presented. This package is well suited for discrete devices, monolithic microwave integrated circuits (MMIC's) and multichip module (MCM) applications. It has low-loss wide-band RF transitions which are necessary to overcome manufacturing tolerances leading to lower per unit cost Potential applications of this new packaging architecture which go beyond the standard requirements of device protection include integration of antennas, compatibility to photonic networks and direct transitions to waveguide systems. Techniques for electromagnetic analysis, thermal control and hermetic sealing were explored. Three dimensional electromagnetic analysis was performed using a finite difference time-domain (FDTD) algorithm and experimentally verified for millimeter-wave package input and output transitions. New multi-material system concepts (AlN, Cu, and diamond thin films) which allow excellent surface finishes to be achieved with enhanced thermal management have been investigated. A new approach utilizing block copolymer coatings was employed to hermetically seal packages which met MIL STD-883.

Big Science, Small-Budget Space Experiment Package Aka MISSE-5: A Hardware And Software Perspective

NASA Technical Reports Server (NTRS)

Krasowski, Michael; Greer, Lawrence; Flatico, Joseph; Jenkins, Phillip; Spina, Dan

2007-01-01

Conducting space experiments with small budgets is a fact of life for many design groups with low-visibility science programs. One major consequence is that specialized space grade electronic components are often too costly to incorporate into the design. Radiation mitigation now becomes more complex as a result of being restricted to the use of commercial off-the-shelf (COTS) parts. Unique hardware and software design techniques are required to succeed in producing a viable instrument suited for use in space. This paper highlights some of the design challenges and associated solutions encountered in the production of a highly capable, low cost space experiment package.

Radiation-Resistant Photon-Counting Detector Package Providing Sub-ps Stability for Laser Time Transfer in Space

NASA Technical Reports Server (NTRS)

Prochzaka, Ivan; Kodat, Jan; Blazej, Josef; Sun, Xiaoli (Editor)

2015-01-01

We are reporting on a design, construction and performance of photon-counting detector packages based on silicon avalanche photodiodes. These photon-counting devices have been optimized for extremely high stability of their detection delay. The detectors have been designed for future applications in fundamental metrology and optical time transfer in space. The detectors have been qualified for operation in space missions. The exceptional radiation tolerance of the detection chip itself and of all critical components of a detector package has been verified in a series of experiments.

Introduction to IND and recursive partitioning, version 1.0

NASA Technical Reports Server (NTRS)

Buntine, Wray; Caruana, Rich

1991-01-01

This manual describes the IND package for learning tree classifiers from data. The package is an integrated C and C shell re-implementation of tree learning routines such as CART, C4, and various MDL and Bayesian variations. The package includes routines for experiment control, interactive operation, and analysis of tree building. The manual introduces the system and its many options, gives a basic review of tree learning, contains a guide to the literature and a glossary, lists the manual pages for the routines, and instructions on installation.

pcr: an R package for quality assessment, analysis and testing of qPCR data

PubMed Central

Ahmed, Mahmoud

2018-01-01

Background Real-time quantitative PCR (qPCR) is a broadly used technique in the biomedical research. Currently, few different analysis models are used to determine the quality of data and to quantify the mRNA level across the experimental conditions. Methods We developed an R package to implement methods for quality assessment, analysis and testing qPCR data for statistical significance. Double Delta CT and standard curve models were implemented to quantify the relative expression of target genes from CT in standard qPCR control-group experiments. In addition, calculation of amplification efficiency and curves from serial dilution qPCR experiments are used to assess the quality of the data. Finally, two-group testing and linear models were used to test for significance of the difference in expression control groups and conditions of interest. Results Using two datasets from qPCR experiments, we applied different quality assessment, analysis and statistical testing in the pcr package and compared the results to the original published articles. The final relative expression values from the different models, as well as the intermediary outputs, were checked against the expected results in the original papers and were found to be accurate and reliable. Conclusion The pcr package provides an intuitive and unified interface for its main functions to allow biologist to perform all necessary steps of qPCR analysis and produce graphs in a uniform way. PMID:29576953

beachmat: A Bioconductor C++ API for accessing high-throughput biological data from a variety of R matrix types

PubMed Central

Pagès, Hervé

2018-01-01

Biological experiments involving genomics or other high-throughput assays typically yield a data matrix that can be explored and analyzed using the R programming language with packages from the Bioconductor project. Improvements in the throughput of these assays have resulted in an explosion of data even from routine experiments, which poses a challenge to the existing computational infrastructure for statistical data analysis. For example, single-cell RNA sequencing (scRNA-seq) experiments frequently generate large matrices containing expression values for each gene in each cell, requiring sparse or file-backed representations for memory-efficient manipulation in R. These alternative representations are not easily compatible with high-performance C++ code used for computationally intensive tasks in existing R/Bioconductor packages. Here, we describe a C++ interface named beachmat, which enables agnostic data access from various matrix representations. This allows package developers to write efficient C++ code that is interoperable with dense, sparse and file-backed matrices, amongst others. We evaluated the performance of beachmat for accessing data from each matrix representation using both simulated and real scRNA-seq data, and defined a clear memory/speed trade-off to motivate the choice of an appropriate representation. We also demonstrate how beachmat can be incorporated into the code of other packages to drive analyses of a very large scRNA-seq data set. PMID:29723188

beachmat: A Bioconductor C++ API for accessing high-throughput biological data from a variety of R matrix types.

PubMed

Lun, Aaron T L; Pagès, Hervé; Smith, Mike L

2018-05-01

Biological experiments involving genomics or other high-throughput assays typically yield a data matrix that can be explored and analyzed using the R programming language with packages from the Bioconductor project. Improvements in the throughput of these assays have resulted in an explosion of data even from routine experiments, which poses a challenge to the existing computational infrastructure for statistical data analysis. For example, single-cell RNA sequencing (scRNA-seq) experiments frequently generate large matrices containing expression values for each gene in each cell, requiring sparse or file-backed representations for memory-efficient manipulation in R. These alternative representations are not easily compatible with high-performance C++ code used for computationally intensive tasks in existing R/Bioconductor packages. Here, we describe a C++ interface named beachmat, which enables agnostic data access from various matrix representations. This allows package developers to write efficient C++ code that is interoperable with dense, sparse and file-backed matrices, amongst others. We evaluated the performance of beachmat for accessing data from each matrix representation using both simulated and real scRNA-seq data, and defined a clear memory/speed trade-off to motivate the choice of an appropriate representation. We also demonstrate how beachmat can be incorporated into the code of other packages to drive analyses of a very large scRNA-seq data set.

Research on a new fiber-optic axial pressure sensor of transformer winding based on fiber Bragg grating

NASA Astrophysics Data System (ADS)

Liu, Yuan; Li, Lianqing; Zhao, Lin; Wang, Jiqiang; Liu, Tongyu

2017-12-01

Based on the principle of the fiber Bragg grating, a new type of fiber-optic pressure sensor for axial force measurement of transformer winding is designed, which is designed with the structure of bending plate beam, the optimization of the packaging process, and material of the sensor. Through the calibration experiment to calibrate the sensor, the field test results of the Taikai transformer factory show that the sensitivity of the sensor is 0.133 pm/kPa and the repeatability error is 2.7% FS. The data of the fiber-optic pressure sensor in different positions maintain consistent and repeatable, which can meet the requirement of the real-time monitoring of the axial force of transformer winding.

Ultraviolet photometry from the Orbiting Astronomical Observatory. XXXIII - The symbiotic star AG Pegasi

NASA Technical Reports Server (NTRS)

Gallagher, J. S.; Webbink, R. F.; Holm, A. V.; Anderson, C. M.

1979-01-01

Ultraviolet broadband photometry obtained with the Wisconsin Experiment Package on OAO 2 is presented for the symbiotic binary star AG Peg. The hot component of the binary is found to be a luminous ultraviolet source, with an energy distribution consistent with its WN6 optical spectral type. Total luminosities of 1000 and 17,000 suns are found for the hot star by assuming, respectively, that the giant primary of AG Peg is a normal M3 III star and that it fills its Roche lobe. The eruptive behavior of AG Peg is shown to require the higher luminosity, and the activity in AG Peg is discussed in terms of a very slow novalike nuclear-powered event.

Examining the Effects of a Behavioural Self-Control Package on the Behaviour of the Distance Learner. REDEAL Research Report #8. Project REDEAL. Research and Evaluation of Distance Education for the Adult Learner.

ERIC Educational Resources Information Center

Powell, Russell; Coldeway, Dan O.

An unsuccessful attempt was made to facilitate study behavior of Athabasca University learners through instruction in behavioral methods of self-control. The general procedure consisted of providing each student with a package containing instructions and materials for the self-application of the strategies of self-monitoring and standard setting.…

Development of a Communication Training Program to Improve Access to Legal Services for People with Complex Communication Needs

ERIC Educational Resources Information Center

Togher, Leanne; Balandin, Susan; Young, Katherine; Given, Fiona; Canty, Michael

2006-01-01

People with communication disabilities experience problems in accessing the justice system. In this article we describe the development of a multimedia package designed to train legal personnel to identify and reduce communication barriers to their services. The training package is being developed collaboratively by a diverse team that included…

GEMINI S-10 - EXPERIMENTS - MICROMETEORITE PACKAGE - MSC

NASA Image and Video Library

1966-08-01

S66-44887 (1 Aug. 1966) --- Single panel from micrometeorite package showing classic hypervelocity impact by micrometeorite particle. Crater is similar to that produced artificially on Earth and by particle impacts on the lunar surface. Particles travel very fast in space and are typically small in size. This impact crater is less than one millimeter in diameter. Photo credit: NASA

Ebola Virus VP35-VP40 Interaction Is Sufficient for Packaging 3E-5E Minigenome RNA into Virus-Like Particles

PubMed Central

Johnson, Reed F.; McCarthy, Sarah E.; Godlewski, Peter J.; Harty, Ronald N.

2006-01-01

The packaging of viral genomic RNA into nucleocapsids and subsequently into virions is not completely understood. Phosphoprotein (P) and nucleoprotein (NP) interactions link NP-RNA complexes with P-L (polymerase) complexes to form viral nucleocapsids. The nucleocapsid then interacts with the viral matrix protein, leading to specific packaging of the nucleocapsid into the virion. A mammalian two-hybrid assay and confocal microscopy were used to demonstrate that Ebola virus VP35 and VP40 interact and colocalize in transfected cells. VP35 was packaged into budding virus-like particles (VLPs) as observed by protease protection assays. Moreover, VP40 and VP35 were sufficient for packaging an Ebola virus minignome RNA into VLPs. Results from immunoprecipitation-reverse transcriptase PCR experiments suggest that VP35 confers specificity of the nucleocapsid for viral genomic RNA by direct VP35-RNA interactions. PMID:16698994

Food product design: emerging evidence for food policy.

PubMed

Al-Hamdani, Mohammed; Smith, Steven

2017-03-01

The research on the impact of specific brand elements such as food descriptors and package colors is underexplored. We tested whether a "light" color and a "low-calorie" descriptor on food packages gain favorable consumer perception ratings as compared with regular packages. Our online experiment recruited 406 adults in a 3 (product type: Chips versus Juice versus Yoghurt) × 2 (descriptor type: regular versus low-calorie) × 2 (color type: regular versus light) mixed design. Dependent variables were sensory (evaluations of the product's nutritional value and quality), product-based (evaluations of the product's physical appeal), and consumer-based (evaluations of the potential consumers of the product) scales. "Low-calorie" descriptors were found to increase sensory ratings as compared with regular descriptors and light-colored packages received higher product-based ratings as compared with their regular-colored counterparts. Food package color and descriptors present a promising venue for understanding preventative measures against obesity.[Formula: see text].

Experimental comparison of forces resisting viral DNA packaging and driving DNA ejection

NASA Astrophysics Data System (ADS)

Keller, Nicholas; Berndsen, Zachary T.; Jardine, Paul J.; Smith, Douglas E.

2017-05-01

We compare forces resisting DNA packaging and forces driving DNA ejection in bacteriophage phi29 with theoretical predictions. Ejection of DNA from prohead-motor complexes is triggered by heating complexes after in vitro packaging and force is inferred from the suppression of ejection by applied osmotic pressure. Ejection force from 0 % to 80 % filling is found to be in quantitative agreement with predictions of a continuum mechanics model that assumes a repulsive DNA-DNA interaction potential based on DNA condensation studies and predicts an inverse-spool conformation. Force resisting DNA packaging from ˜80 % to 100 % filling inferred from optical tweezers studies is also consistent with the predictions of this model. The striking agreement with these two different measurements suggests that the overall energetics of DNA packaging is well described by the model. However, since electron microscopy studies of phi29 do not reveal a spool conformation, our findings suggest that the spool model overestimates the role of bending rigidity and underestimates the role of intrastrand repulsion. Below ˜80 % filling the inferred forces resisting packaging are unexpectedly lower than the inferred ejection forces, suggesting that in this filling range the forces are less accurately determined or strongly temperature dependent.

Assessing direct analysis in real-time-mass spectrometry (DART-MS) for the rapid identification of additives in food packaging.

PubMed

Ackerman, L K; Noonan, G O; Begley, T H

2009-12-01

The ambient ionization technique direct analysis in real time (DART) was characterized and evaluated for the screening of food packaging for the presence of packaging additives using a benchtop mass spectrometer (MS). Approximate optimum conditions were determined for 13 common food-packaging additives, including plasticizers, anti-oxidants, colorants, grease-proofers, and ultraviolet light stabilizers. Method sensitivity and linearity were evaluated using solutions and characterized polymer samples. Additionally, the response of a model additive (di-ethyl-hexyl-phthalate) was examined across a range of sample positions, DART, and MS conditions (temperature, voltage and helium flow). Under optimal conditions, molecular ion (M+H+) was the major ion for most additives. Additive responses were highly sensitive to sample and DART source orientation, as well as to DART flow rates, temperatures, and MS inlet voltages, respectively. DART-MS response was neither consistently linear nor quantitative in this setting, and sensitivity varied by additive. All additives studied were rapidly identified in multiple food-packaging materials by DART-MS/MS, suggesting this technique can be used to screen food packaging rapidly. However, method sensitivity and quantitation requires further study and improvement.

Experimental comparison of forces resisting viral DNA packaging and driving DNA ejection.

PubMed

Keller, Nicholas; Berndsen, Zachary T; Jardine, Paul J; Smith, Douglas E

2017-05-01

We compare forces resisting DNA packaging and forces driving DNA ejection in bacteriophage phi29 with theoretical predictions. Ejection of DNA from prohead-motor complexes is triggered by heating complexes after in vitro packaging and force is inferred from the suppression of ejection by applied osmotic pressure. Ejection force from 0% to 80% filling is found to be in quantitative agreement with predictions of a continuum mechanics model that assumes a repulsive DNA-DNA interaction potential based on DNA condensation studies and predicts an inverse-spool conformation. Force resisting DNA packaging from ∼80% to 100% filling inferred from optical tweezers studies is also consistent with the predictions of this model. The striking agreement with these two different measurements suggests that the overall energetics of DNA packaging is well described by the model. However, since electron microscopy studies of phi29 do not reveal a spool conformation, our findings suggest that the spool model overestimates the role of bending rigidity and underestimates the role of intrastrand repulsion. Below ∼80% filling the inferred forces resisting packaging are unexpectedly lower than the inferred ejection forces, suggesting that in this filling range the forces are less accurately determined or strongly temperature dependent.

Electronic packaging: new results in singulation by Laser Microjet

NASA Astrophysics Data System (ADS)

Wagner, Frank; Sibailly, Ochelio; Richerzhagen, Bernold

2004-07-01

Cutting electronic packages that are produced in a matrix array fashion is an important process and deals with the ready-to-use devices. Thus an increase in the singulation yield is directly correlated to an increase in benefit. Due to the usage of different substrate materials, the saws encounter big problems in terms of lifetime and constancy of cut quality in these applications. Today"s equipment manufacturers are not yet in the position to propose an adequate solution for all types of packages. Compared to classical laser cutting, the water-jet guided laser technology minimizes the heat damages in any kind of sample. This new material processing method consists in guiding a laser beam inside a hair thin, lowpressure water-jet by total internal reflection, and is applied to package singulation since two years approximately. Using a frequency doubled Nd:YAG laser guided by a water jet, an LTCC-ceramics based package is singulated according to a scribe and break process. Speeds of 2-10 mm/s are reached in the LTTC and 40 mm/s in the mold compound. The process is wear-free and provides very good edge quality of the LTCC and the mold compound as well as reliable separation of the packages.

Phase Change Material Heat Sink for an ISS Flight Experiment

NASA Technical Reports Server (NTRS)

Quinn, Gregory; Stieber, Jesse; Sheth, Rubik; Ahlstrom, Thomas

2015-01-01

A flight experiment is being constructed to utilize the persistent microgravity environment of the International Space Station (ISS) to prove out operation of a microgravity compatible phase change material (PCM) heat sink. A PCM heat sink can help to reduce the overall mass and volume of future exploration spacecraft thermal control systems (TCS). The program is characterizing a new PCM heat sink that incorporates a novel phase management approach to prevent high pressures and structural deformation that often occur with PCM heat sinks undergoing cyclic operation in microgravity. The PCM unit was made using brazed aluminum construction with paraffin wax as the fusible material. It is designed to be installed into a propylene glycol and water cooling loop, with scaling consistent with the conceptual designs for the Orion Multipurpose Crew Vehicle. This paper reports on the construction of the PCM heat sink and on initial ground test results conducted at UTC Aerospace Systems prior to delivery to NASA. The prototype will be tested later on the ground and in orbit via a self-contained experiment package developed by NASA Johnson Space Center to operate in an ISS EXPRESS rack.

Performance of conduction cooled splittable superconducting magnet package for linear accelerators

DOE PAGES

Kashikhin, Vladimire S.; Andreev, N.; Cheban, S.; ...

2016-02-19

New Linear Superconducting Accelerators need a superconducting magnet package installed inside SCRF Cryomodules to focus and steer electron or proton beams. A superconducting magnet package was designed and built as a collaborative effort of FNAL and KEK. The magnet package includes one quadrupole, and two dipole windings. It has a splittable in the vertical plane configuration, and features for conduction cooling. The magnet was successfully tested at room temperature, in a liquid He bath, and in a conduction cooling experiment. The paper describes the design and test results including: magnet cooling, training, and magnetic measurements by rotational coils. Furthermore, themore » effects of superconductor and iron yoke magnetization, hysteresis, and fringe fields are discussed.« less

Quantifying the Hydrodynamic Performance of an Explosively-Driven Two-Shock Source

NASA Astrophysics Data System (ADS)

Furlanetto, Michael; Bauer, Amy; King, Robert; Buttler, William; Olson, Russell; Hagelberg, Carl

2015-06-01

An explosively-driven experimental package capable of generating a tunable two-shock drive would enable a host of experiments in shock physics. To make the best use of such a platform, though, its symmetry, reproducibility, and performance must be characterized thoroughly. We report on a series of experiments on a particular two-shock design that used shock reverberation between the sample and a heavy anvil to produce a second shock. Drive package diameters were varied between 50 and 76 mm in order to investigate release wave propagation. We used proton radiography to characterize the detonation and reverberation fronts within the high explosive elements of the packages, as well as surface velocimetry to measure the resulting shock structure in the sample under study. By fielding more than twenty channels of velocimetry per shot, we were able to quantify the symmetry and reproducibility of the drive.

A streamlined Python framework for AT-TPC data analysis

NASA Astrophysics Data System (ADS)

Taylor, J. Z.; Bradt, J.; Bazin, D.; Kuchera, M. P.

2017-09-01

User-friendly data analysis software has been developed for the Active-Target Time Projection Chamber (AT-TPC) experiment at the National Superconducting Cyclotron Laboratory at Michigan State University. The AT-TPC, commissioned in 2014, is a gas-filled detector that acts as both the detector and target for high-efficiency detection of low-intensity, exotic nuclear reactions. The pytpc framework is a Python package for analyzing AT-TPC data. The package was developed for the analysis of 46Ar(p, p) data. The existing software was used to analyze data produced by the 40Ar(p, p) experiment that ran in August, 2015. Usage of the package was documented in an analysis manual both to improve analysis steps and aid in the work of future AT-TPC users. Software features and analysis methods in the pytpc framework will be presented along with the 40Ar results.

Experiments with a Regional Vector-Vorticity Model, and Comparison with Other Models

NASA Astrophysics Data System (ADS)

Konor, C. S.; Dazlich, D. A.; Jung, J.; Randall, D. A.

2017-12-01

The Vector-Vorticity Model (VVM) is an anelastic model with a unique dynamical core that predicts the three-dimensional vorticity instead of the three-dimensional momentum. The VVM is used in the CRMs of the Global Quasi-3D Multiscale Modeling Framework, which is discussed by Joon-Hee Jung and collaborators elsewhere in this session. We are updating the physics package of the VVM, replacing it with the physics package of the System for Atmosphere Modeling (SAM). The new physics package includes a double-moment microphysics, Mellor-Yamada turbulence, Monin-Obukov surface fluxes, and the RRTMG radiation parameterization. We briefly describe the VVM and show results from standard test cases, including TWP-ICE. We compare the results with those obtained using the earlier physics. We also show results from experiments on convection aggregation in radiative-convective equilibrium, and compare with those obtained using both SAM and the Regional Atmospheric Modeling System (RAMS).

Conceptual definition of a high voltage power supply test facility

NASA Technical Reports Server (NTRS)

Biess, John J.; Chu, Teh-Ming; Stevens, N. John

1989-01-01

NASA Lewis Research Center is presently developing a 60 GHz traveling wave tube for satellite cross-link communications. The operating voltage for this new tube is - 20 kV. There is concern about the high voltage insulation system and NASA is planning a space station high voltage experiment that will demonstrate both the 60 GHz communications and high voltage electronics technology. The experiment interfaces, requirements, conceptual design, technology issues and safety issues are determined. A block diagram of the high voltage power supply test facility was generated. It includes the high voltage power supply, the 60 GHz traveling wave tube, the communications package, the antenna package, a high voltage diagnostics package and a command and data processor system. The interfaces with the space station and the attached payload accommodations equipment were determined. A brief description of the different subsystems and a discussion of the technology development needs are presented.

Apollo 17 Lunar Surface Experiment: Lunar Ejecta and Meteorites Experiment

NASA Image and Video Library

1972-11-30

S72-37257 (November 1972) --- The Lunar Ejecta and Meteorites Experiment (S-202), one of the experiments of the Apollo Lunar Surface Experiments Package which will be carried on the Apollo 17 lunar landing mission. The purpose of this experiment is to measure the physical parameters of primary and secondary particles impacting the lunar surface.

Rocket-borne thermal plasma instrument "MIPEX" for the ionosphere D, E layer in-situ measurements

NASA Astrophysics Data System (ADS)

Fang, H. K.; Chen, A. B. C.; Lin, C. C. H.; Wu, T. J.; Liu, K. S.; Chuang, C. W.

2017-12-01

In this presentation, the design concepts, performances and status of a thermal plasma particle instrument package "Mesosphere and Ionosphere Plasma Exploration complex (MIPEX)", which is going to be installed onboard a NSPO-funded hybrid rocket, to investigate the electrodynamic processes in ionosphere D, E layers above Taiwan are reported. MIPEX is capable of measuring plasma characteristics including ion temperature, ion composition, ion drift, electron temperature and plasma density at densities as low as 1-10 cm-1. This instrument package consists of an improved retarding potential analyzer with a channel electron multiplier (CEM), a simplified ion drift meter and a planar Langmuir probe. To achieve the working atmospheric pressure of CEM at the height of lower D layer ( 70km), a portable vacuum pump is also placed in the package. A prototype set of the MIPEX has been developed and tested in the Space Plasma Operation Chamber (SPOC) at NCKU, where in ionospheric plasma is generated by back-diffusion plasma sources. A plasma density of 10-106 cm-1, ion temperature of 300-1500 K and electron temperature of 1000-3000K is measured and verified. Limited by the flight platform and the performance of the instruments, the in-situ plasma measurements at the Mesosphere and lower Thermosphere is very challenging and rare. MIPEX is capable of extending the altitude of the effective plasma measurement down to 70 km height and this experiment can provide unique high-quality data of the plasma environment to explore the ion distribution and the electrodynamic processes in the Ionosphere D, E layers at dusk.

Performance Results for Massachusetts and Rhode Island Deep Energy Retrofit Pilot Community

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gates, C.; Neuhauser, K.

2014-03-01

Between December, 2009 and December, 2012 42 deep energy retrofit (DER) projects were completed through a DER pilot program sponsored by National Grid and conducted in Massachusetts and Rhode Island. 37 of these projects were comprehensive retrofits while 5 were partial DERs, meaning that high performance retrofit was implemented for a single major enclosure component or a limited number of major enclosure components. The 42 DER projects represent 60 units of housing. The comprehensive projects all implemented a consistent 'package' of measures in terms of the performance targeted for major building components. Projects exhibited some variations in the approach tomore » implementing the retrofit package. Pre- and post-retrofit air leakage measurements were performed for each of the projects. Each project also reported information about project costs including identification of energy-related costs. Post-retrofit energy-use data was obtained for 29 of the DER projects. Post-retrofit energy use was analyzed based on the net energy used by the DER project regardless of whether the energy was generated on site or delivered to the site. Homeowner surveys were returned by 12 of the pilot participants. Based on the community experience, this DER package is expected to result in yearly source energy use near 110 MMBtu/year or approximately 40% below the Northeast regional average. Larger to medium sized homes that successful implement these retrofits can be expected to achieve source EUI that is comparable to Passive House targets for new construction. The community of DER projects show post-retrofit airtightness below 1.5 ACH50 to be eminently achievable.« less

Packaging waste prevention in the distribution of fruit and vegetables: An assessment based on the life cycle perspective.

PubMed

Tua, Camilla; Nessi, Simone; Rigamonti, Lucia; Dolci, Giovanni; Grosso, Mario

2017-04-01

In recent years, alternative food supply chains based on short distance production and delivery have been promoted as being more environmentally friendly than those applied by the traditional retailing system. An example is the supply of seasonal and possibly locally grown fruit and vegetables directly to customers inside a returnable crate (the so-called 'box scheme'). In addition to other claimed environmental and economic advantages, the box scheme is often listed among the packaging waste prevention measures. To check whether such a claim is soundly based, a life cycle assessment was carried out to verify the real environmental effectiveness of the box scheme in comparison to the Italian traditional distribution. The study focused on two reference products, carrots and apples, which are available in the crate all year round. An experience of a box scheme carried out in Italy was compared with some traditional scenarios where the product is distributed loose or packaged at the large-scale retail trade. The packaging waste generation, 13 impact indicators on environment and human health and energy consumptions were calculated. Results show that the analysed experience of the box scheme, as currently managed, cannot be considered a packaging waste prevention measure when compared with the traditional distribution of fruit and vegetables. The weaknesses of the alternative system were identified and some recommendations were given to improve its environmental performance.

A software package for interactive motor unit potential classification using fuzzy k-NN classifier.

PubMed

Rasheed, Sarbast; Stashuk, Daniel; Kamel, Mohamed

2008-01-01

We present an interactive software package for implementing the supervised classification task during electromyographic (EMG) signal decomposition process using a fuzzy k-NN classifier and utilizing the MATLAB high-level programming language and its interactive environment. The method employs an assertion-based classification that takes into account a combination of motor unit potential (MUP) shapes and two modes of use of motor unit firing pattern information: the passive and the active modes. The developed package consists of several graphical user interfaces used to detect individual MUP waveforms from a raw EMG signal, extract relevant features, and classify the MUPs into motor unit potential trains (MUPTs) using assertion-based classifiers.

I-deas TMG to NX Space Systems Thermal Model Conversion and Computational Performance Comparison

NASA Technical Reports Server (NTRS)

Somawardhana, Ruwan

2011-01-01

CAD/CAE packages change on a continuous basis as the power of the tools increase to meet demands. End -users must adapt to new products as they come to market and replace legacy packages. CAE modeling has continued to evolve and is constantly becoming more detailed and complex. Though this comes at the cost of increased computing requirements Parallel processing coupled with appropriate hardware can minimize computation time. Users of Maya Thermal Model Generator (TMG) are faced with transitioning from NX I -deas to NX Space Systems Thermal (SST). It is important to understand what differences there are when changing software packages We are looking for consistency in results.

Apollo lunar surface experiments package

NASA Technical Reports Server (NTRS)

1972-01-01

Developments in the ALSEP program are reported. A summary of the status for the total ALSEP program is included. Other areas discussed include: (1) status of Apollo 16 (array D) and Apollo 17 (array E), (2) lunar seismic profiling experiment, (3) lunar ejecta and meteorites experiment, and (4) lunar mass spectrometer experiments.

The first lunar outpost: The design reference mission and a new era in lunar science

NASA Technical Reports Server (NTRS)

Lofgren, Gary E.

1993-01-01

The content of the First Lunar Outpost (FLO) Design Reference Mission has been formulated and a 'strawman' science program has been established. The mission consists of two independent launches using heavy lift vehicles that land directly on the lunar surface. A habitat module and support systems are flown to the Moon first. After confirmation of a successful deployment of the habitat systems, the crewed lunar lander is launched and piloted to within easy walking distance (2 km) of the habitat. By eliminating the Apollo style lunar orbit rendezvous, landing sites at very high latitudes can be considered. A surface rover and the science experiments will accompany the crew. The planned stay time is 45 days, two lunar days and one night. A payload of 3.3 metric tons will support a series of geophysics, geology, astronomy, space physics, resource utilization, and life science experiments. Sample return is 150 to 200 kg. The rover is unpressurized and can carry four astronauts or two astronauts and 500 kg of payload. The rover can also operate in robotic mode with the addition of a robotics package. The science and engineering experiment strategy is built around a representative set of place holder experiments.

Compact, Engineered, 2-Micron Coherent Doppler Wind Lidar Prototype for Field and Airborne Validation: Doppler Aerosol WiNd Lidar (DAWN). Interim Review #1 (6 months)

NASA Technical Reports Server (NTRS)

Kavaya, Michael J.; Singh, Upendra N.; Koch, Grady J.; Yu, Jirong; Amzajerdian, Farzin; Trieu, Bo C.; Petros, Mulugeta

2006-01-01

A new project, selected in 2005 by NASA's Science Mission Directorate (SMD), under the Instrument Incubator Program (IIP), will be described. The 3-year effort is intended to design, fabricate, and demonstrate a packaged, rugged, compact, space-qualifiable coherent Doppler wind lidar (DWL) transceiver capable of future validation in an aircraft and/or Unmanned Aerial Vehicle (UAV). The state-of-the-art 2-micron coherent DWL breadboard at NASA/LaRC will be engineered and compactly packaged consistent with future aircraft flights. The packaged transceiver will be integrated into a coherent DWL system test bed at LaRC. Atmospheric wind measurements will be made to validate the packaged technology. This will greatly advance the coherent part of the hybrid DWL solution to the need for global tropospheric wind measurements.

Structural testing of the Los Alamos National Laboratory Heat Source/Radioisotopic Thermoelectric Generator shipping container

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bronowski, D.R.; Madsen, M.M.

The Heat Source/Radioisotopic Thermoelectric Generator shipping container is a Type B packaging design currently under development by Los Alamos National Laboratory. Type B packaging for transporting radioactive material is required to maintain containment and shielding after being exposed to the normal and hypothetical accident environments defined in Title 10 Code of Federal Regulations Part 71. A combination of testing and analysis is used to verify the adequacy of this package design. This report documents the test program portion of the design verification, using several prototype packages. Four types of testing were performed: 30-foot hypothetical accident condition drop tests in threemore » orientations, 40-inch hypothetical accident condition puncture tests in five orientations, a 21 psi external overpressure test, and a normal conditions of transport test consisting of a water spray and a 4 foot drop test. 18 refs., 104 figs., 13 tabs.« less

Fostering students’ thinking skill and social attitude through STAD cooperative learning technique on tenth grade students of chemistry class

NASA Astrophysics Data System (ADS)

Kriswintari, D.; Yuanita, L.; Widodo, W.

2018-04-01

The aim of this study was to develop chemistry learning package using Student Teams Achievement Division (STAD) cooperative learning technique to foster students’ thinking skills and social attitudes. The chemistry learning package consisting of lesson plan, handout, students’ worksheet, thinking skill test, and observation sheet of social attitude was developed using the Dick and Carey model. Research subject of this study was chemistry learning package using STAD which was tried out on tenth grade students of SMA Trimurti Surabaya. The tryout was conducted using the one-group pre-test post-test design. Data was collected through observation, test, and questionnaire. The obtained data were analyzed using descriptive qualitative analysis. The findings of this study revealed that the developed chemistry learning package using STAD cooperative learning technique was categorized valid, practice and effective to be implemented in the classroom to foster students’ thinking skill and social attitude.

Packaging Technology for SiC High Temperature Circuits Operable up to 500 Degrees Centigrade

NASA Technical Reports Server (NTRS)

Chen, Lian-Yu

2002-01-01

New high temperature low power 8-pin packages have been fabricated using commercial fabrication service. These packages are made of aluminum nitride and 96 percent alumina with Au metallization. The new design of these packages provides the chips inside with EM shielding. Wirebond geometry control has been achieved for precise mechanical tests. Au wirebond samples with 45 degree heel-angle have been tested using wireloop test module. The geometry control improves the consistency of measurement of the wireloop breaking point.Also reported on is a parametric study of the thermomechanical reliability of a Au thick-film based SiC die-attach assembly using nonlinear finite element analysis (FEA) was conducted to optimize the die-attach thermo-mechanical performance for operation at temperatures from room temperature to 500 degrees Centigrade. This parametric study centered on material selection, structure design and process control.

Chemkin-II: A Fortran chemical kinetics package for the analysis of gas-phase chemical kinetics

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kee, R.J.; Rupley, F.M.; Miller, J.A.

1989-09-01

This document is the user's manual for the second-generation Chemkin package. Chemkin is a software package for whose purpose is to facilitate the formation, solution, and interpretation of problems involving elementary gas-phase chemical kinetics. It provides an especially flexible and powerful tool for incorporating complex chemical kinetics into simulations of fluid dynamics. The package consists of two major software components: an Interpreter and Gas-Phase Subroutine Library. The Interpreter is a program that reads a symbolic description of an elementary, user-specified chemical reaction mechanism. One output from the Interpreter is a data file that forms a link to the Gas-Phase Subroutinemore » Library. This library is a collection of about 100 highly modular Fortran subroutines that may be called to return information on equation of state, thermodynamic properties, and chemical production rates.« less

Design and evaluation of thin metal surface insulation for hypersonic flight

NASA Technical Reports Server (NTRS)

Miller, R. C.; Petach, A. M.

1976-01-01

An all-metal insulation was studied as a thermal protection system for hypersonic vehicles. Key program goals included fabricating the insulation in thin packages which are optimized for high temperature insulation of an actively cooled aluminum structure, and the use of state-of-the-art alloys. The insulation was fabricated from 300 series stainless steel in thicknesses of 0.8 to 12 mm. The outer, 0.127 mm thick, skin was textured to accommodate thermal expansion and oxidized to increase emittance. The thin insulating package was achieved using an insulation concept consisting of foil radiation shields spaced within the package, and conical foil supports to carry loads from the skin and maintain package dimensions. Samples of the metal-insulation were tested to evaluate thermal insulation capability, rain and sand erosion resistance, high temperature oxidation resistance, applied load capability, and high temperature emittance.

ontologyX: a suite of R packages for working with ontological data.

PubMed

Greene, Daniel; Richardson, Sylvia; Turro, Ernest

2017-04-01

Ontologies are widely used constructs for encoding and analyzing biomedical data, but the absence of simple and consistent tools has made exploratory and systematic analysis of such data unnecessarily difficult. Here we present three packages which aim to simplify such procedures. The ontologyIndex package enables arbitrary ontologies to be read into R, supports representation of ontological objects by native R types, and provides a parsimonius set of performant functions for querying ontologies. ontologySimilarity and ontologyPlot extend ontologyIndex with functionality for straightforward visualization and semantic similarity calculations, including statistical routines. ontologyIndex , ontologyPlot and ontologySimilarity are all available on the Comprehensive R Archive Network website under https://cran.r-project.org/web/packages/ . Daniel Greene dg333@cam.ac.uk. Supplementary data are available at Bioinformatics online. © The Author 2016. Published by Oxford University Press.

Packaging signals in single-stranded RNA viruses: nature's alternative to a purely electrostatic assembly mechanism.

PubMed

Stockley, Peter G; Twarock, Reidun; Bakker, Saskia E; Barker, Amy M; Borodavka, Alexander; Dykeman, Eric; Ford, Robert J; Pearson, Arwen R; Phillips, Simon E V; Ranson, Neil A; Tuma, Roman

2013-03-01

The formation of a protective protein container is an essential step in the life-cycle of most viruses. In the case of single-stranded (ss)RNA viruses, this step occurs in parallel with genome packaging in a co-assembly process. Previously, it had been thought that this process can be explained entirely by electrostatics. Inspired by recent single-molecule fluorescence experiments that recapitulate the RNA packaging specificity seen in vivo for two model viruses, we present an alternative theory, which recognizes the important cooperative roles played by RNA-coat protein interactions, at sites we have termed packaging signals. The hypothesis is that multiple copies of packaging signals, repeated according to capsid symmetry, aid formation of the required capsid protein conformers at defined positions, resulting in significantly enhanced assembly efficiency. The precise mechanistic roles of packaging signal interactions may vary between viruses, as we have demonstrated for MS2 and STNV. We quantify the impact of packaging signals on capsid assembly efficiency using a dodecahedral model system, showing that heterogeneous affinity distributions of packaging signals for capsid protein out-compete those of homogeneous affinities. These insights pave the way to a new anti-viral therapy, reducing capsid assembly efficiency by targeting of the vital roles of the packaging signals, and opens up new avenues for the efficient construction of protein nanocontainers in bionanotechnology.

Alcohol Warning Label Perceptions: Do Warning Sizes and Plain Packaging Matter?

PubMed

Al-Hamdani, Mohammed; Smith, Steven M

2017-01-01

There is a dearth of research on the effectiveness of stringent alcohol warning labels. Our experiment tested whether increasing the size of an alcohol health warning lowers product-based ratings. We examined whether plain packaging lowers ratings of alcohol products and the consumers who use them, increases ratings of bottle "boringness," and enhances warning recognition compared with branded packaging. A total of 440 adults (51.7% female) viewed one of three warning sizes (50%, 75%, or 90% of label surface) on either a plain or branded bottle of distilled spirits, wine, and beer. Participants also rated alcohol bottles on product-based (assessing the product itself), consumer-based (assessing perceptions of consumers of the product), and bottle boringness ratings, and then attempted to recognize the correct warning out of four choices. As expected, the size of warning labels lowered product-based ratings. Similarly, plain packaging lowered product-based and consumer-based ratings and increased bottle boringness but only for wine bottles. Further, plain packaging increased the odds of warning recognition on bottles of distilled spirits. This study shows that plain packaging and warning size (similar to the graphic warnings on cigarette packages) affect perceptions about alcohol bottles. It also shows that plain packaging increases the likelihood for correct health warning recognition, which builds the case for alcohol warning and packaging research and policy.

Effect of Packaging on Shelf-life and Lutein Content of Marigold (Tagetes erecta L.) Flowers.

PubMed

Pal, Sayani; Ghosh, Probir Kumar; Bhattacharjee, Paramita

2016-01-01

African marigold (Tagetes erecta L.) flowers are highly valued for their ornamental appeal as well as medicinal properties. However, their short shelf lives cause high post-harvest loss and limit their export potential. The review of patents and research articles revealed that different types of packaging designs/materials have been successfully employed for extension of shelf lives of cut flowers. The current work focuses on designing of different packaging configurations and selection of best configuration for preservation of marigold cut flowers. Ten packaging configurations, composed of four different packaging materials i.e., low density polyethylene (LDPE), polyethylene terephthalate, glassine paper and cellophane paper, were designed. Each pack, consisting of 20 ± 1 g of marigold flowers along with non-packaged control set were stored at 23 ± 2°C, 80% R.H., in an environmental chamber and the flowers were evaluated for their sensory attributes, phytochemical characteristics and physicochemical parameters of senescence to determine their shelf lives. Flowers packed in LDPE bag showed highest shelf life of 8 days with a lead of 4 days compared to control (shelf life - 4 days). This study also established for the first time the phenomenon of carotenogenesis in marigold cut flowers with significantly (P<0.01) higher production of lutein in LDPE packaged flowers. LDPE pack was the best design among the ten package designs, in preserving lutein content of marigold flowers and extending their shelf lives. This economically viable packaging can not only boost the export potential of this ornamental flower, but also allow utilization of nutraceutical potency of lutein.

The bifurcated stem loop 4 (SL4) is crucial for efficient packaging of mouse mammary tumor virus (MMTV) genomic RNA.

PubMed

Mustafa, Farah; Vivet-Boudou, Valérie; Jabeen, Ayesha; Ali, Lizna M; Kalloush, Rawan M; Marquet, Roland; Rizvi, Tahir A

2018-06-21

Packaging the mouse mammary tumor virus (MMTV) genomic RNA (gRNA) requires the entire 5' untranslated region (UTR) in conjunction with the first 120 nucleotides of the gag gene. This region includes several palindromic (pal) sequence(s) and stable stem loops (SLs). Among these, stem loop 4 (SL4) adopts a bifurcated structure consisting of three stems, two apical loops, and an internal loop. Pal II, located in one of the apical loops, mediates gRNA dimerization, a process intricately linked to packaging. We thus hypothesized that the bifurcated SL4 structure could constitute the major gRNA packaging determinant. To test this hypothesis, the two apical loops and the flanking sequences forming the bifurcated SL4 were individually mutated. These mutations all had deleterious effects on gRNA packaging and propagation. Next, single and compensatory mutants were designed to destabilize then recreate the bifurcated SL4 structure. A structure-function analysis using bioinformatics predictions and RNA chemical probing revealed that mutations that led to the loss of the SL4 bifurcated structure abrogated RNA packaging and propagation, while compensatory mutations that recreated the native SL4 structure restored RNA packaging and propagation to wild type levels. Altogether, our results demonstrate that SL4 constitutes the principal packaging determinant of MMTV gRNA. Our findings further suggest that SL4 acts as a structural switch that can not only differentiate between RNA for translation versus packaging/dimerization, but its location also allows differentiation between spliced and unspliced RNAs during gRNA encapsidation.

GUIdock-VNC: using a graphical desktop sharing system to provide a browser-based interface for containerized software

PubMed Central

Mittal, Varun; Hung, Ling-Hong; Keswani, Jayant; Kristiyanto, Daniel; Lee, Sung Bong

2017-01-01

Abstract Background: Software container technology such as Docker can be used to package and distribute bioinformatics workflows consisting of multiple software implementations and dependencies. However, Docker is a command line–based tool, and many bioinformatics pipelines consist of components that require a graphical user interface. Results: We present a container tool called GUIdock-VNC that uses a graphical desktop sharing system to provide a browser-based interface for containerized software. GUIdock-VNC uses the Virtual Network Computing protocol to render the graphics within most commonly used browsers. We also present a minimal image builder that can add our proposed graphical desktop sharing system to any Docker packages, with the end result that any Docker packages can be run using a graphical desktop within a browser. In addition, GUIdock-VNC uses the Oauth2 authentication protocols when deployed on the cloud. Conclusions: As a proof-of-concept, we demonstrated the utility of GUIdock-noVNC in gene network inference. We benchmarked our container implementation on various operating systems and showed that our solution creates minimal overhead. PMID:28327936

SEDA: A software package for the Statistical Earthquake Data Analysis

NASA Astrophysics Data System (ADS)

Lombardi, A. M.

2017-03-01

In this paper, the first version of the software SEDA (SEDAv1.0), designed to help seismologists statistically analyze earthquake data, is presented. The package consists of a user-friendly Matlab-based interface, which allows the user to easily interact with the application, and a computational core of Fortran codes, to guarantee the maximum speed. The primary factor driving the development of SEDA is to guarantee the research reproducibility, which is a growing movement among scientists and highly recommended by the most important scientific journals. SEDAv1.0 is mainly devoted to produce accurate and fast outputs. Less care has been taken for the graphic appeal, which will be improved in the future. The main part of SEDAv1.0 is devoted to the ETAS modeling. SEDAv1.0 contains a set of consistent tools on ETAS, allowing the estimation of parameters, the testing of model on data, the simulation of catalogs, the identification of sequences and forecasts calculation. The peculiarities of routines inside SEDAv1.0 are discussed in this paper. More specific details on the software are presented in the manual accompanying the program package.

Packaging, deployment, and panel design concepts for a truss-stiffened 7-panel precision deployable reflector with feed boom

NASA Technical Reports Server (NTRS)

Heard, Walter L., Jr.; Collins, Timothy J.; Dyess, James W.; Kenner, Scott; Bush, Harold G.

1993-01-01

A concept is presented for achieving a remotely deployable truss-stiffened reflector consisting of seven integrated sandwich panels that form the reflective surface, and an integrated feed boom. The concept has potential for meeting aperture size and surface precision requirements for some high-frequency microwave remote sensing applications. The packaged reflector/feed boom configuration is a self-contained unit that can be conveniently attached to a spacecraft bus. The package has a cylindrical envelope compatible with typical launch vehicle shrouds. Dynamic behavior of a deployed configuration having a 216-inch focal length and consisting of 80-inch-diameter, two-inch-thick panels is examined through finite-element analysis. Results show that the feed boom and spacecraft bus can have a large impact on the fundamental frequency of the deployed configuration. Two candidate rib-stiffened sandwich panel configurations for this application are described, and analytical results for panel mass and stiffness are presented. Results show that the addition of only a few rib stiffeners, if sufficiently deep, can efficiently improve sandwich panel stiffness.

User's Manual for FOMOCO Utilities-Force and Moment Computation Tools for Overset Grids

NASA Technical Reports Server (NTRS)

Chan, William M.; Buning, Pieter G.

1996-01-01

In the numerical computations of flows around complex configurations, accurate calculations of force and moment coefficients for aerodynamic surfaces are required. When overset grid methods are used, the surfaces on which force and moment coefficients are sought typically consist of a collection of overlapping surface grids. Direct integration of flow quantities on the overlapping grids would result in the overlapped regions being counted more than once. The FOMOCO Utilities is a software package for computing flow coefficients (force, moment, and mass flow rate) on a collection of overset surfaces with accurate accounting of the overlapped zones. FOMOCO Utilities can be used in stand-alone mode or in conjunction with the Chimera overset grid compressible Navier-Stokes flow solver OVERFLOW. The software package consists of two modules corresponding to a two-step procedure: (1) hybrid surface grid generation (MIXSUR module), and (2) flow quantities integration (OVERINT module). Instructions on how to use this software package are described in this user's manual. Equations used in the flow coefficients calculation are given in Appendix A.

SEDA: A software package for the Statistical Earthquake Data Analysis

PubMed Central

Lombardi, A. M.

2017-01-01

In this paper, the first version of the software SEDA (SEDAv1.0), designed to help seismologists statistically analyze earthquake data, is presented. The package consists of a user-friendly Matlab-based interface, which allows the user to easily interact with the application, and a computational core of Fortran codes, to guarantee the maximum speed. The primary factor driving the development of SEDA is to guarantee the research reproducibility, which is a growing movement among scientists and highly recommended by the most important scientific journals. SEDAv1.0 is mainly devoted to produce accurate and fast outputs. Less care has been taken for the graphic appeal, which will be improved in the future. The main part of SEDAv1.0 is devoted to the ETAS modeling. SEDAv1.0 contains a set of consistent tools on ETAS, allowing the estimation of parameters, the testing of model on data, the simulation of catalogs, the identification of sequences and forecasts calculation. The peculiarities of routines inside SEDAv1.0 are discussed in this paper. More specific details on the software are presented in the manual accompanying the program package. PMID:28290482

GUIdock-VNC: using a graphical desktop sharing system to provide a browser-based interface for containerized software.

PubMed

Mittal, Varun; Hung, Ling-Hong; Keswani, Jayant; Kristiyanto, Daniel; Lee, Sung Bong; Yeung, Ka Yee

2017-04-01

Software container technology such as Docker can be used to package and distribute bioinformatics workflows consisting of multiple software implementations and dependencies. However, Docker is a command line-based tool, and many bioinformatics pipelines consist of components that require a graphical user interface. We present a container tool called GUIdock-VNC that uses a graphical desktop sharing system to provide a browser-based interface for containerized software. GUIdock-VNC uses the Virtual Network Computing protocol to render the graphics within most commonly used browsers. We also present a minimal image builder that can add our proposed graphical desktop sharing system to any Docker packages, with the end result that any Docker packages can be run using a graphical desktop within a browser. In addition, GUIdock-VNC uses the Oauth2 authentication protocols when deployed on the cloud. As a proof-of-concept, we demonstrated the utility of GUIdock-noVNC in gene network inference. We benchmarked our container implementation on various operating systems and showed that our solution creates minimal overhead. © The Authors 2017. Published by Oxford University Press.

DNA Packaging Specificity of Bacteriophage N15 with an Excursion into the Genetics of a Cohesive End Mismatch

PubMed Central

Feiss, Michael; Young Min, Jea; Sultana, Sawsan; Patel, Priyal; Sippy, Jean

2015-01-01

During DNA replication by the λ-like bacteriophages, immature concatemeric DNA is produced by rolling circle replication. The concatemers are processed into mature chromosomes with cohesive ends, and packaged into prohead shells, during virion assembly. Cohesive ends are generated by the viral enzyme terminase, which introduces staggered nicks at cos, an approx. 200 bp-long sequence containing subsites cosQ, cosN and cosB. Interactions of cos subsites of immature concatemeric DNA with terminase orchestrate DNA processing and packaging. To initiate DNA packaging, terminase interacts with cosB and nicks cosN. The cohesive ends of N15 DNA differ from those of λ at 2/12 positions. Genetic experiments show that phages with chromosomes containing mismatched cohesive ends are functional. In at least some infections, the cohesive end mismatch persists through cyclization and replication, so that progeny phages of both allelic types are produced in the infected cell. N15 possesses an asymmetric packaging specificity: N15 DNA is not packaged by phages λ or 21, but surprisingly, N15-specific terminase packages λ DNA. Implications for genetic interactions among λ-like bacteriophages are discussed. PMID:26633301

Progress of the Dust Accumulation and Removal Technology Experiment (DART) for the Mars 2001 Lander

NASA Technical Reports Server (NTRS)

Jenkins, Phillip; Landis, Geoffrey A.; Wilt, David; Krasowski, Michael; Greer, Lawrence; Baraona, Cosmo; Scheiman, David

2005-01-01

Dust deposition could be a significant problem for photovoltaic array operation for long duration missions on the surface of Mars. Measurements made by Pathfinder showed 0.3 percent loss of solar array performance per day due to dust obscuration. We have designed an experiment package, "DART", which is part of the Mars ISPP Precursor (MIP) package, to fly on the Mars-2001 Surveyor Lander. This mission, to launch in April 2001, will arrive on Mars in January 2002. The DART experiment is designed to quantify dust deposition from the Mars atmosphere, measure the properties of settled dust, measure the effect of dust deposition on array performance, and test several methods of clearing dust from solar cells.

Evaluation of the prototype dual-axis wall attitude measurement sensor

NASA Technical Reports Server (NTRS)

Wong, Douglas T.

1994-01-01

A prototype dual-axis electrolytic tilt sensor package for angular position measurements was built and evaluated in a laboratory environment. The objective was to investigate the use of this package for making wind tunnel wall attitude measurements for the National Transonic Facility (NTF) at NASA Langley Research Center (LaRC). The instrumentation may replace an existing, more costly, and less rugged servo accelerometer package (angle-of-attack package) currently in use. The dual-axis electrolytic tilt sensor package contains two commercial electrolytic tilt sensors thermally insulated with NTF foam, all housed within a stainless steel package. The package is actively heated and maintained at 160 F using foil heating elements. The laboratory evaluation consisted of a series of tests to characterize the linearity, repeatability, cross-axis interaction, lead wire effect, step response, thermal time constant, and rectification errors. Tests revealed that the total RMS errors for the x-axis sensor is 0.084 degree, and 0.182 degree for the y-axis sensor. The RMS errors are greater than the 0.01 degree specification required for NTF wall attitude measurements. It is therefore not a viable replacement for the angle-of-attack package in the NTF application. However, with some physical modifications, it can be used as an inexpensive 5-degree range dual-axis inclinometer with overall accuracy approaching 0.01 degree under less harsh environments. Also, the data obtained from the tests can be valuable for wind tunnel applications of most types of electrolytic tilt sensors.

Apollo 12 Mission image - View of part of the deployed Apollo Lunar Surface Experiment Package (ALSEP)

NASA Image and Video Library

1969-11-19

AS12-47-6918 (19 Nov. 1969) --- Astronaut Alan L. Bean, lunar module pilot, took this photograph of three of the components of the Apollo Lunar Surface Experiments Package (ALSEP) which was deployed on the moon during the first Apollo 12 extravehicular activity (EVA). The Passive Seismic Experiment (PSE) is in the center foreground. The largest object is the Central Station; and the white object on legs is the Suprathermal Ion Detector Experiment (SIDE). A portion of the shadow of astronaut Charles Conrad Jr., commander, can be seen at the left center edge of the picture. Astronaut Richard F. Gordon Jr., command module pilot, remained with the Apollo 12 Command and Service Modules (CSM) in lunar orbit while Conrad and Bean descended in the Lunar Module (LM) to explore the moon.

GEMINI-TITAN (GT)-XI - MISC. EXPERIMENTS - MSC

NASA Image and Video Library

1966-03-22

S66-05515 (2 June 1966) --- Gemini-11 Experiment S-9 Nuclear Emulsion. This experiment will be used to study the cosmic radiation incident on Earth's atmosphere, to obtain detailed chemical composition of the heavy primary nuclei and to search for rare particles. Equipment is a rectangular package eight and a half by six by three inches weighing 15 pounds and including the nuclear emulsion film stack, motor to advance the emulsion and a timer to regulate the motor. The package is mounted atop the spacecraft retro adapter section prior to launch, is activated at insertion, and is retrieved by the EVA pilot. The experiment is conducted with the spacecraft in plus or minus 15 degrees of Earth's average magnetic field vector. Sponsors are NASA's Office of Space Science and Applications and the U.S. Naval Research Laboratories. Photo credit: NASA

Partial view of the deployed Apollo Lunar Surface Experiments Package

NASA Image and Video Library

1972-04-21

AS16-113-18347 (21 April 1972) --- A partial view of the Apollo 16 Apollo Lunar Surface Experiments Package (ALSEP) in deployed configuration on the lunar surface as photographed during the mission's first extravehicular activity (EVA), on April 21, 1972. The Passive Seismic Experiment (PSE) is in the foreground center; Central Station (C/S) is in center background, with the Radioisotope Thermoelectric Generator (RTG) to the left. One of the anchor flags for the Active Seismic Experiment (ASE) is at right. While astronauts John W. Young, commander; and Charles M. Duke Jr., lunar module pilot; descended in the Apollo 16 Lunar Module (LM) "Orion" to explore the Descartes highlands landing site on the moon, astronaut Thomas K. Mattingly II, command module pilot, remained with the Command and Service Modules (CSM) "Casper" in lunar orbit.

YAMM - Yet Another Menu Manager

NASA Technical Reports Server (NTRS)

Mazer, Alan S.; Weidner, Richard J.

1991-01-01

Yet Another Menu Manager (YAMM) computer program an application-independent menuing package of software designed to remove much difficulty and save much time inherent in implementation of front ends of large packages of software. Provides complete menuing front end for wide variety of applications, with provisions for independence from specific types of terminals, configurations that meet specific needs of users, and dynamic creation of menu trees. Consists of two parts: description of menu configuration and body of application code. Written in C.

Implementation of the NCAR (National Centre for Atmospheric Research) Graphics Package at ARL (Aeronautical Research Laboratory).

DTIC Science & Technology

1988-01-01

VELVCT. .. .. ... ... ... .... ... 57 E.5 Arguments for Subroutine EZVEC .. .. .. ... ... ... ... .... 59 E.6 Using VELVCT with the Mapping Packege EZMAP...VELVCT with the Mapping Packege EZMAP Using this routine to put vectors on an arbitrary background drawn by EZMAP is a bit tricky. The arithmetic...squares solutions to overdetermined linear systems. 129 K.2 The "Fishpack" Package This packege was included on the NCAR distribution tape. It consists of

Designing a User-Friendly Microcomputer-Based Laboratory Package through the Factor Analysis of Teacher Evaluations

ERIC Educational Resources Information Center

Lavonen, Jari; Juuti, Kalle; Meisalo, Veijo

2003-01-01

In this study we analyse how the experiences of chemistry teachers on the use of a Microcomputer-Based Laboratory (MBL), gathered by a Likert-scale instrument, can be utilized to develop the new package "Empirica 2000." We used exploratory factor analysis to identify the essential features in a large set of questionnaire data to see how…

Learning Experiences in Population Education. Population Education Programme Service, Volume 3. For the Non-Formal Education System.

ERIC Educational Resources Information Center

United Nations Educational, Scientific, and Cultural Organization, Bangkok (Thailand). Regional Office for Education in Asia and the Pacific.

One of the main products of the Regional Workshop for the Development of Packages of Adequate Learning Requirements in Population is this prototype package of curriculum materials in population education. The workshop notes that one of the shortcomings of country programs in population education is that the content integrated in school subjects is…

View of the Challenger's payload bay and the Plasma Diagnostic package

NASA Technical Reports Server (NTRS)

1985-01-01

The solar optical universal polarimeter (SOUP) experiment is visible among the cluster of Spacelab 2 hardware in the cargo bay of the Shuttle Challenger. Various components of the instrument positioning system (IPS) are conspicuous at the center of the frame. The Plasma Diagnostic package (PDP) is seen attached to the remote manipulator system (RMS) above the open payload bay.

Validation of the new code package APOLLO2.8 for accurate PWR neutronics calculations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Santamarina, A.; Bernard, D.; Blaise, P.

2013-07-01

This paper summarizes the Qualification work performed to demonstrate the accuracy of the new APOLLO2.S/SHEM-MOC package based on JEFF3.1.1 nuclear data file for the prediction of PWR neutronics parameters. This experimental validation is based on PWR mock-up critical experiments performed in the EOLE/MINERVE zero-power reactors and on P.I. Es on spent fuel assemblies from the French PWRs. The Calculation-Experiment comparison for the main design parameters is presented: reactivity of UOX and MOX lattices, depletion calculation and fuel inventory, reactivity loss with burnup, pin-by-pin power maps, Doppler coefficient, Moderator Temperature Coefficient, Void coefficient, UO{sub 2}-Gd{sub 2}O{sub 3} poisoning worth, Efficiency ofmore » Ag-In-Cd and B4C control rods, Reflector Saving for both standard 2-cm baffle and GEN3 advanced thick SS reflector. From this qualification process, calculation biases and associated uncertainties are derived. This code package APOLLO2.8 is already implemented in the ARCADIA new AREVA calculation chain for core physics and is currently under implementation in the future neutronics package of the French utility Electricite de France. (authors)« less

Aging Study Of EPDM O-Ring Material For The H1616 Shipping Package - Three Year Status

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stefek, T.; Daugherty, W.; Skidmore, E.

This is a 3-year status report for tasks carried out per Task Technical Plan SRNL-STI-2011-00506. A series of tasks/experiments were performed at the Savannah River National Laboratory (SRNL) to monitor the aging performance of ethylene propylene diene monomer (EPDM) O-rings used in the H1616 shipping package. The test data provide a technical basis to extend the annual maintenance of the H1616 shipping package to three years and to predict the life of the EPDM O-rings at the bounding service conditions.

Approaches to the mechanisms of song memorization and singing provide evidence for a procedural memory.

PubMed

Hultsch, Henrike; Todt, Dietmar

2004-06-01

There is growing evidence that, during song learning, birds do not only acquire 'what to sing' (the inventory of behavior), but also 'how to sing' (the singing program), including order-features of song sequencing. Common Nightingales Luscinia megarhynchos acquire such serial information by segmenting long strings of heard songs into smaller subsets or packages, by a process reminiscent of the chunking of information as a coding mechanism in short term memory. Here we report three tutoring experiments on nightingales that examined whether such 'chunking' was susceptible to experimental cueing. The experiments tested whether (1) 'temporal phrasing' (silent intersong intervals spaced out at particular positions of a tutored string), or (2) 'stimulus novelty' (groups of novel song-types added to a basic string), or (3) 'pattern similarity' in the phonetic structure of songs (here: sharing of song initials) would induce package boundaries (or chunking) at the manipulated sequential positions. The results revealed cueing effects in experiments (1) and (2) but not in experiment (3). The finding that birds used temporal variables as cues for chunking does not require the assumption that package formation is a cognitive strategy. Rather, it points towards a mechanism of procedural memory operating in the song acquisition of birds.

Apollo lunar surface experiments package. Apollo 17 ALSEP (array E) familiarization course handout

NASA Technical Reports Server (NTRS)

1972-01-01

The familiarization course for the Apollo 17 ALSEP (ARRAY E) is presented. The subjects discussed are: (1) power and data subsystems, (2) lunar surface gravimeter, (3) lunar mass spectrometer, (4) lunar seismic profiling experiment, and (5) heat flow experiment.

Software for the Integration of Multiomics Experiments in Bioconductor.

PubMed

Ramos, Marcel; Schiffer, Lucas; Re, Angela; Azhar, Rimsha; Basunia, Azfar; Rodriguez, Carmen; Chan, Tiffany; Chapman, Phil; Davis, Sean R; Gomez-Cabrero, David; Culhane, Aedin C; Haibe-Kains, Benjamin; Hansen, Kasper D; Kodali, Hanish; Louis, Marie S; Mer, Arvind S; Riester, Markus; Morgan, Martin; Carey, Vince; Waldron, Levi

2017-11-01

Multiomics experiments are increasingly commonplace in biomedical research and add layers of complexity to experimental design, data integration, and analysis. R and Bioconductor provide a generic framework for statistical analysis and visualization, as well as specialized data classes for a variety of high-throughput data types, but methods are lacking for integrative analysis of multiomics experiments. The MultiAssayExperiment software package, implemented in R and leveraging Bioconductor software and design principles, provides for the coordinated representation of, storage of, and operation on multiple diverse genomics data. We provide the unrestricted multiple 'omics data for each cancer tissue in The Cancer Genome Atlas as ready-to-analyze MultiAssayExperiment objects and demonstrate in these and other datasets how the software simplifies data representation, statistical analysis, and visualization. The MultiAssayExperiment Bioconductor package reduces major obstacles to efficient, scalable, and reproducible statistical analysis of multiomics data and enhances data science applications of multiple omics datasets. Cancer Res; 77(21); e39-42. ©2017 AACR . ©2017 American Association for Cancer Research.

A Saturn launched X-ray astronomy experiment. Volume 1: S-027

NASA Technical Reports Server (NTRS)

1971-01-01

The S-027 X-Ray Astronomy Experiment originally proposed in early 1966, was developed to detect X-rays in the 2 keV to 10 keV range. Both a prototype unit and flight unit were constructed with the prototype unit also serving as the engineering model, the qualification test unit, and after refurbishment, as the back-up flight unit. Two Ground Support Equipment consoles were built to verify the experiment operation. A photograph of one experiment package with its Ground Support Equipment is shown. The S-027 experiment was scheduled for launch in 1968/69 and although both units were completed and tested to the extent that either would be ready for the scheduled launch, delays in the space program resulted in a launch date slip of several years. When the 1968/69 launch delay became official, provisions were made for storage of the two experiment packages at SCI Electronics in Huntsville, Alabama until a new launch date could be established.

A Review of Microgravity Levels on Ten OARE Shuttle Missions

NASA Technical Reports Server (NTRS)

McPherson, Kevin M.

1998-01-01

The Orbital Acceleration Research Experiment (OARE) is an accelerometer package with nano-g sensitivity and on-orbit bias calibration capabilities. The OARE consists of a three axis miniature electrostatic accelerometer (MESA), a full in-flight bias and scale factor calibration station, and an on-board microprocessor for experiment control and data storage. Originally designed to measure and record the aerodynamic acceleration environment of the NASA Space Shuttles during re-entry, the OARE has been used on ten shuttle missions to measure the quasi-steady acceleration environment (<1 Hz) of the Orbiter while in low-Earth orbit. The effects on the quasi-steady acceleration environment from Orbiter systems, Orbiter attitude, Orbiter altitude, and crew activity are well understood as a result of these ten shuttle missions. This knowledge of the quasi-steady acceleration realm has direct application to understanding the quasi-steady acceleration environment expected for the International Space Station (ISS). This paper will summarize the more salient aspects of this quasi-steady acceleration knowledge base.

Design and experimental verification for optical module of optical vector-matrix multiplier.

PubMed

Zhu, Weiwei; Zhang, Lei; Lu, Yangyang; Zhou, Ping; Yang, Lin

2013-06-20

Optical computing is a new method to implement signal processing functions. The multiplication between a vector and a matrix is an important arithmetic algorithm in the signal processing domain. The optical vector-matrix multiplier (OVMM) is an optoelectronic system to carry out this operation, which consists of an electronic module and an optical module. In this paper, we propose an optical module for OVMM. To eliminate the cross talk and make full use of the optical elements, an elaborately designed structure that involves spherical lenses and cylindrical lenses is utilized in this optical system. The optical design software package ZEMAX is used to optimize the parameters and simulate the whole system. Finally, experimental data is obtained through experiments to evaluate the overall performance of the system. The results of both simulation and experiment indicate that the system constructed can implement the multiplication between a matrix with dimensions of 16 by 16 and a vector with a dimension of 16 successfully.

Measurement of the production cross section for charmed baryons in proton–nucleus interactions at 70 GeV

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ryadovikov, V. N., E-mail: riadovikov@ihep.ru; Aleev, A. N.; Ardashev, E. N.

2016-03-15

The results of an analysis of data from the SERP-E-184 experiment devoted to studying mechanisms of the production of charmed particles in proton–nucleus interactions at 70 GeV and their decays are presented. The data in question were obtained upon irradiating the SVD-2 active target consisting of carbon, silicon, and lead plates with a beam of 70-GeV protons. A detailed simulation on the basis of the FRITIOF7.02 and GEANT3.21 code packages made it possible to optimize event-selection criteria and to calculate the detection efficiency for Λ{sub c}{sup +} baryons. After selecting a signal from the threebody decay of a Λ{sub c}{supmore » +} baryon, the inclusive cross section for its production at near-threshold energies, its lifetime, and the parameter of the A dependence of the cross section were found. The Λ{sub c}{sup +} -baryon yields are tabulated along with data from other experiments and theoretical predictions.« less

sapFinder: an R/Bioconductor package for detection of variant peptides in shotgun proteomics experiments.

PubMed

Wen, Bo; Xu, Shaohang; Sheynkman, Gloria M; Feng, Qiang; Lin, Liang; Wang, Quanhui; Xu, Xun; Wang, Jun; Liu, Siqi

2014-11-01

Single nucleotide variations (SNVs) located within a reading frame can result in single amino acid polymorphisms (SAPs), leading to alteration of the corresponding amino acid sequence as well as function of a protein. Accurate detection of SAPs is an important issue in proteomic analysis at the experimental and bioinformatic level. Herein, we present sapFinder, an R software package, for detection of the variant peptides based on tandem mass spectrometry (MS/MS)-based proteomics data. This package automates the construction of variation-associated databases from public SNV repositories or sample-specific next-generation sequencing (NGS) data and the identification of SAPs through database searching, post-processing and generation of HTML-based report with visualized interface. sapFinder is implemented as a Bioconductor package in R. The package and the vignette can be downloaded at http://bioconductor.org/packages/devel/bioc/html/sapFinder.html and are provided under a GPL-2 license. © The Author 2014. Published by Oxford University Press. All rights reserved. For Permissions, please e-mail: journals.permissions@oup.com.

How Many Peripheral Solder Joints in a Surface Mounted Design Experience Inelastic Strains?

NASA Astrophysics Data System (ADS)

Suhir, E.; Yi, S.; Ghaffarian, R.

2017-03-01

It has been established that it is the peripheral solder joints that are the most vulnerable in the ball-grid-array (BGA) and column-grid-array (CGA) designs and most often fail. As far as the long-term reliability of a soldered microelectronics assembly as a whole is concerned, it makes a difference, if just one or more peripheral joints experience inelastic strains. It is clear that the low cycle fatigue lifetime of the solder system is inversely proportional to the number of joints that simultaneously experience inelastic strains. A simple and physically meaningful analytical expression (formula) is obtained for the prediction, at the design stage, of the number of such joints, if any, for the given effective thermal expansion (contraction) mismatch of the package and PCB; materials and geometrical characteristics of the package/PCB assembly; package size; and, of course, the level of the yield stress in the solder material. The suggested formula can be used to determine if the inelastic strains in the solder material could be avoided by the proper selection of the above characteristics and, if not, how many peripheral joints are expected to simultaneously experience inelastic strains. The general concept is illustrated by a numerical example carried out for a typical BGA package. The suggested analytical model (formula) is applicable to any soldered microelectronics assembly. The roles of other important factors, such as, e.g., solder material anisotropy, grain size, and their random orientation within a joint, are viewed in this analysis as less important factors than the level of the interfacial stress. The roles of these factors will be accounted for in future work and considered, in addition to the location of the joint, in a more complicated, more sophisticated, and more comprehensive reliability/fatigue model.

Effects of first exposure to plain cigarette packaging on smoking behaviour and attitudes: a randomised controlled study.

PubMed

Maynard, Olivia M; Leonards, Ute; Attwood, Angela S; Bauld, Linda; Hogarth, Lee; Munafò, Marcus R

2015-03-13

Plain packaging requires tobacco products to be sold in packs with a standard shape, method of opening and colour, leaving the brand name in a standard font and location. We ran a randomised controlled trial to investigate the impact of plain packaging on smoking behaviour and attitudes. In a parallel group randomised trial design, 128 daily smokers smoked cigarettes from their usual UK brand, or a plain Australian brand that was closely matched to their usual UK brand for 24 hours. Primary outcomes were number of cigarettes smoked and volume of smoke inhaled per cigarette. Secondary outcomes were self-reported ratings of motivation to quit, cigarette taste, experience of using the pack, experience of smoking, attributes of the pack, perceptions of the health warning, changes in smoking behaviour, and views on plain packaging. There was no evidence that pack type had an effect on either of the primary measures (ps > 0.279). However, smokers using plain cigarette packs rated the experience of using the pack more negatively (-0.52, 95% CI -0.82 to -0.22, p = 0.001), rated the pack attributes more negatively (-1.59, 95% CI -1.80 to -1.39, p < 0.001), and rated the health warning as more impactful (+0.51, 95% CI 0.24 to 0.78, p < 0.001). Plain cigarette packs reduce ratings of the experience of using the cigarette pack, and ratings of the pack attributes, and increase the self-perceived impact of the health warning, but do not change smoking behaviour, at least in the short term. Current Controlled Trials ISRCTN52982308. Registered 27 June 2013.

STS-52 Space Shuttle mission report

NASA Technical Reports Server (NTRS)

Fricke, Robert W., Jr.

1992-01-01

The STS-52 Space Shuttle Program Mission Report provides a summary of the Orbiter, External Tank (ET), Solid Rocket Booster/Redesigned Solid Rocket Motor (SRB/RSRM), and the Space Shuttle main engine (SSME) subsystem performance during the fifty-first flight of the Space Shuttle Program, and the thirteenth flight of the Orbiter vehicle Columbia (OV-102). In addition to the Orbiter, the flight vehicle consisted of the following: an ET (designated as ET-55/LWT-48); three SSME's, which were serial numbers 2030, 2015, and 2034 in positions 1, 2, and 3, respectively; and two SRB's, which were designated BI-054. The lightweight RSRM's that were installed in each SRB were designated 360L027A for the left SRB and 360Q027B for the right SRB. The primary objectives of this flight were to successfully deploy the Laser Geodynamic Satellite (LAGEOS-2) and to perform operations of the United States Microgravity Payload-1 (USMP-1). The secondary objectives of this flight were to perform the operations of the Attitude Sensor Package (ASP), the Canadian Experiments-2 (CANEX-2), the Crystals by Vapor Transport Experiment (CVTE), the Heat Pipe Performance Experiment (HPP), the Commercial Materials Dispersion Apparatus Instrumentation Technology Associates Experiments (CMIX), the Physiological System Experiment (PSE), the Commercial Protein Crystal Growth (CPCG-Block 2), the Shuttle Plume Impingement Experiment (SPIE), and the Tank Pressure Control Experiment (TPCE) payloads.

STS-52 Space Shuttle mission report

NASA Astrophysics Data System (ADS)

Fricke, Robert W., Jr.

1992-12-01

The STS-52 Space Shuttle Program Mission Report provides a summary of the Orbiter, External Tank (ET), Solid Rocket Booster/Redesigned Solid Rocket Motor (SRB/RSRM), and the Space Shuttle main engine (SSME) subsystem performance during the fifty-first flight of the Space Shuttle Program, and the thirteenth flight of the Orbiter vehicle Columbia (OV-102). In addition to the Orbiter, the flight vehicle consisted of the following: an ET (designated as ET-55/LWT-48); three SSME's, which were serial numbers 2030, 2015, and 2034 in positions 1, 2, and 3, respectively; and two SRB's, which were designated BI-054. The lightweight RSRM's that were installed in each SRB were designated 360L027A for the left SRB and 360Q027B for the right SRB. The primary objectives of this flight were to successfully deploy the Laser Geodynamic Satellite (LAGEOS-2) and to perform operations of the United States Microgravity Payload-1 (USMP-1). The secondary objectives of this flight were to perform the operations of the Attitude Sensor Package (ASP), the Canadian Experiments-2 (CANEX-2), the Crystals by Vapor Transport Experiment (CVTE), the Heat Pipe Performance Experiment (HPP), the Commercial Materials Dispersion Apparatus Instrumentation Technology Associates Experiments (CMIX), the Physiological System Experiment (PSE), the Commercial Protein Crystal Growth (CPCG-Block 2), the Shuttle Plume Impingement Experiment (SPIE), and the Tank Pressure Control Experiment (TPCE) payloads.

NASA's Getaway Special.

ERIC Educational Resources Information Center

Randal, Judith

1978-01-01

The "Getaway Special" is NASA's semiofficial program for low-budget researchers, who can arrange bookings for their own space experiments on regular flights of the space shuttle. Information about arranging for NASA to take individual experiment packages is presented. (LBH)

Herpesvirus capsid assembly and DNA packaging

PubMed Central

Heming, Jason D.; Conway, James F.; Homa, Fred L.

2017-01-01

Herpes simplex virus type I (HSV-1) is the causative agent of several pathologies ranging in severity from the common cold sore to life-threatening encephalitic infection. During productive lytic infection, over 80 viral proteins are expressed in a highly regulated manner, resulting in the replication of viral genomes and assembly of progeny virions. The virion of all herpesviruses consists of an external membrane envelope, a proteinaceous layer called the tegument, and an icosahedral capsid containing the double-stranded linear DNA genome. The capsid shell of HSV-1 is built from four structural proteins: a major capsid protein, VP5, which forms the capsomers (hexons and pentons), the triplex consisting of VP19C and VP23 found between the capsomers, and VP26 which binds to VP5 on hexons but not pentons. In addition, the dodecameric pUL6 portal complex occupies one of the 12 capsid vertices, and the capsid vertex specific component (CVSC), a heterotrimer complex of pUL17, pUL25 and pUL36 binds specifically to the triplexes adjacent to each penton. The capsid is assembled in the nucleus where the viral genome is packaged into newly assembled closed capsid shells. Cleavage and packaging of replicated, concatemeric viral DNA requires the seven viral proteins encoded by the UL6, UL15, UL17, UL25, UL28, UL32, and UL33 genes. Considerable advances have been made in understanding the structure of the herpesvirus capsid and the function of several of the DNA packaging proteins by applying biochemical, genetic, and structural techniques. This review is a summary of recent advances with respect to the structure of the HSV-1 virion capsid and what is known about the function of the seven packaging proteins and their interactions with each other and with the capsid shell. PMID:28528442

Installation package - SIMS prototype system 1A

NASA Technical Reports Server (NTRS)

1976-01-01

This report consists of details for the installation, operation and maintenance of a prototype heating and hot water system, designed for residential or light commercial applications. This system consists of the following subsystems: air type collectors, pebble bed thermal storage, air handling unit, air to water heat exchanger, hot water preheat tank, auxiliary energy, ducting system.

The Development of a Model for Adult Education in Nutrition and Cardiovascular Disease.

ERIC Educational Resources Information Center

Walker, Susan K.; Villano, Maurice W.

Two nutrition education modules were developed on cardiovascular disease and fat-controlled diet consisting of a self-instruction leader's guide and teaching package to conduct learning sessions for the participants. The sessions consisted of an audio-visual presentation, situations related to the module topic, group discussion, role-playing,…

A Cause and A Solution for the Underprediction of Extreme Wave Events in the Northeast Pacific

NASA Astrophysics Data System (ADS)

Ellenson, A. N.; Ozkan-Haller, H. T.; Thomson, J.; Brown, A. C.; Haller, M. C.

2016-12-01

Along the coastlines of Washington and Oregon, at least one 10 m wave height event occurs every year, and the strongest storms produce wave heights of 14-15 m. Extremely high wave heights can cause severe damage to coastal infrastructure and pose hazards to stakeholders along the coast. A system which can accurately predict such sea states is important for quantifying risk and aiding in preparation for extreme wave events. This study explores how to optimize forecast model performance for extreme wave events by utilizing different physics packages or wind input in four model configurations. The different wind input products consist of a reanalyzed Global Forecasting System (GFS) wind input and a Climate Forecast System Reanalysis (CFSR) from the National Center of Environmental Prediction (NCEP). The physics packages are the Tolman-Chalikov (1996) ST2 physics package and the Ardhuin et al (2009) ST4 physics package associated with version 4.18 of WaveWatch III. A hindcast was previously performed to assess the wave character along the Pacific Northwest Coastline for wave energy applications. Inspection of hindcast model results showed that the operational model, which consisted of ST2 physics and GFS wind, underpredicted events where wave height exceeded six meters.The under-prediction is most severe for cases with the combined conditions of a distant cyclone and a strong coastal jet. Three such cases were re-analyzed with the four model configurations. Model output is compared with observations at NDBC buoy 46050, offshore of Newport, OR. The model configuration consisting of ST4 physics package and CFSR wind input performs best as compared with the original model, reducing significant wave height underprediction from 1.25 m to approximately 0.67 m and mean wave direction error from 30 degrees to 17 degrees for wave heights greater than 6 m. Spectral analysis shows that the ST4-CFSR model configuration best resolves southerly wave energy, and all model configurations tend to overestimate northerly wave energy. This directional distinction is important when attempting to identify which atmospheric feature has induced the extreme wave energy.

Easing access to R using 'shiny' to create graphical user interfaces: An example for the R package 'Luminescence'

NASA Astrophysics Data System (ADS)

Burow, Christoph; Kreutzer, Sebastian; Dietze, Michael; Fuchs, Margret C.; Schmidt, Christoph; Fischer, Manfred; Brückner, Helmut

2017-04-01

Since the release of the R package 'Luminescence' (Kreutzer et al., 2012) the functionality of the package has been greatly enhanced by implementing further functions for measurement data processing, statistical analysis and graphical output. Despite its capabilities for complex and non-standard analysis of luminescence data, working with the command-line interface (CLI) of R can be tedious at best and overwhelming at worst, especially for users without experience in programming languages. Even though much work is put into simplifying the usage of the package to continuously lower the entry threshold, at least basic knowledge of R will always be required. Thus, the potential user base of the package cannot be exhausted, at least as long as the CLI is the only means of utilising the 'Luminescence' package. But even experienced users may find it tedious to iteratively run a function until a satisfying results is produced. For example, plotting data is also at least partly subject to personal aesthetic tastes in accordance with the information it is supposed to convey and iterating through all the possible options in the R CLI can be a time-consuming task. An alternative approach to the CLI is the graphical user interface (GUI), which allows direct, interactive manipulation and interaction with the underlying software. For users with little or no experience with command-lines a GUI offers intuitive access that counteracts the perceived steep learning curve of a CLI. Even though R lacks native support for GUI functions, its capabilities of linking it to other programming languages allows to utilise external frameworks to build graphical user interfaces. A recent attempt to provide a GUI toolkit for R was the introduction of the 'shiny' package (Chang et al., 2016), which allows automatic construction of HTML, CSS and JavaScript based user interfaces straight from R. Here, we give (1) a brief introduction to the 'shiny' framework for R, before we (2) present a GUI for the R package 'Luminescence' in the form of interactive web applications. These applications can be accessed online so that a user is not even required to have a local installation of R and which provide access to most of the plotting functions of the R package 'Luminescence'. These functionalities will be demonstrated live during the PICO session. References Chang, W., Cheng, J., Allaire, JJ., Xie, Y., McPherson, J., 2016. shiny: Web Application Framework for R. R package version 0.13.2. https://CRAN.R-project.org/package=shiny Kreutzer, S., Schmidt, C., Fuchs, M.C., Dietze, M., Fischer, M., Fuchs, M., 2012. Introducing an R package for luminescence dating analysis. Ancient TL, 30: 1-8, 2012.

Operational Design: Distilling Clarity from Complexity for Decisive Action

DTIC Science & Technology

2012-08-01

forces came within six miles of Richmond, the Chickahominy River overflowed its banks and split the Union forces before they could attack. The...key vulnerabilities. The system, controlled by four sector operation centers, consisted of a number of diverse radar systems with limited repair...ec tio n Su st ai nm en t Interdiction Package C4 IIS R Co m ba t Po w er Fo rc e Pr ot ec tio n Su st ai nm en t Maneuver Package C4

Recent developments with the ORSER system

NASA Technical Reports Server (NTRS)

Baumer, G. M.; Turner, B. J.; Myers, W. L.

1981-01-01

Additions to the ORSER remote sensing data processing package are described. The ORSER package consists of about 35 individual programs that are grouped into preprocessing, data analysis, and display subsystems. Additional data formats and data management, data transformation, and geometric correlation programs were supplemented to the preprocessing subsystem. Enhancements to the data analysis techniques include a maximum likelihood classifier (MAXCLASS) and a new version of the STATS program which makes delineation of training areas easier and allows for detection of outlier points. Ongoing developments are also described.

User's manual for the two-dimensional transputer graphics toolkit

NASA Technical Reports Server (NTRS)

Ellis, Graham K.

1988-01-01

The user manual for the 2-D graphics toolkit for a transputer based parallel processor is presented. The toolkit consists of a package of 2-D display routines that can be used for the simulation visualizations. It supports multiple windows, double buffered screens for animations, and simple graphics transformations such as translation, rotation, and scaling. The display routines are written in occam to take advantage of the multiprocessing features available on transputers. The package is designed to run on a transputer separate from the graphics board.

Mold Heating and Cooling Pump Package Operator Interface Controls Upgrade

DOE Office of Scientific and Technical Information (OSTI.GOV)

Josh A. Salmond

2009-08-07

The modernization of the Mold Heating and Cooling Pump Package Operator Interface (MHC PP OI) consisted of upgrading the antiquated single board computer with a proprietary operating system to off-the-shelf hardware and off-the-shelf software with customizable software options. The pump package is the machine interface between a central heating and cooling system that pumps heat transfer fluid through an injection or compression mold base on a local plastic molding machine. The operator interface provides the intelligent means of controlling this pumping process. Strict temperature control of a mold allows the production of high quality parts with tight tolerances and lowmore » residual stresses. The products fabricated are used on multiple programs.« less

Ceramic ball grid array package stress analysis

NASA Astrophysics Data System (ADS)

Badri, S. H. B. S.; Aziz, M. H. A.; Ong, N. R.; Sauli, Z.; Alcain, J. B.; Retnasamy, V.

2017-09-01

The ball grid array (BGA), a form of chip scale package (CSP), was developed as one of the most advanced surface mount devices, which may be assembled by an ordinary surface ball bumps are used instead of plated nickel and gold (Ni/Au) bumps. Assembly and reliability of the BGA's printed circuit board (PCB), which is soldered by conventional surface mount technology is considered in this study. The Ceramic Ball Grid Array (CBGA) is a rectangular ceramic package or square-shaped that will use the solder ball for external electrical connections instead of leads or wire for connections. The solder balls will be arranged in an array or grid at the bottom of the ceramic package body. In this study, ANSYS software is used to investigate the stress on the package for 2 balls and 4 balls of the CBGA package with the various force range of 1-3 Newton applied to the top of the die, top of the substrate and side of the substrate. The highest maximum stress was analyzed and the maximum equivalent stress was observed on the solder ball and the die. From the simulation result, the CBGA package with less solder balls experience higher stress compared to the package with many solder balls. Therefore, less number of solder ball on the CBGA package results higher stress and critically affect the reliability of the solder balls itself, substrate and die which can lead to the solder crack and also die crack.

Astronaut Alan Bean with subpackages of the ALSEP during EVA

NASA Image and Video Library

1969-11-19

AS12-46-6807 (19 Nov. 1969) --- Astronaut Alan L. Bean, lunar module pilot, traverses with the two sub packages of the Apollo Lunar Surface Experiments Package (ALSEP) during the first Apollo 12 extravehicular activity (EVA). Bean deployed the ALSEP components 300 feet from the Lunar Module (LM). The LM and deployed erectable S-band antenna can be seen in the background.

Materials Assessment of Insulating Foam in the 9977 Shipping Package for Long-Term Storage - Annual Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

McWilliams, A. J.

The 9977 shipping package is being evaluated for long-term storage applications in the K-Area Complex (KAC) with specific focus on the packaging foam material. A rigid closed cell polyurethane foam, LAST-A-FOAM® FR-3716, produced by General Plastics Manufacturing Company is sprayed and expands to fill the void between the inner container and the outer shell of the package. The foam is sealed in this annular space and is not accessible. During shipping and storage, the foam experiences higher than ambient temperatures from the heat generated by nuclear material within the package creating the potential for degradation of the foam. A seriesmore » of experiments is underway to determine the extent of foam degradation. Foam samples of three densities have been aging at elevated temperatures 160 °F, 160 °F + 50% relative humidity (RH), 185 °F, 215 °F, and 250 °F since 2014. Samples were periodically removed and tested. After approximately 80 weeks, samples conditioned at 160 °F, 160 °F + 50% RH, and 185 °F have retained initial property values while samples conditioned at 215 °F have reduced intumescence. Samples conditioned at 250 °F have shown the most degradation, loss of volume, mass, absorbed energy under compression, intumescence, and increased flammability. Based on the initial data, temperatures up to 185 °F have not yet shown an adverse effect on the foam properties and it is recommended that exposure of FR-3716 foam to temperatures in excess of 250 °F be avoided or minimized. Testing will continue beyond the 96 week mark. This will provide additional data to help define the long-term behavior for the lower temperature conditions. Additional testing will be pursued in an attempt to identify transition points (threshold times and temperatures) at the higher temperatures of interest, as well as possible benefits of aging within the relatively oxygen-free environment the foam experiences inside the 9977 shipping package.« less

Design and fabrication of a foldable 3D silicon based package for solid state lighting applications

NASA Astrophysics Data System (ADS)

Sokolovskij, R.; Liu, P.; van Zeijl, H. W.; Mimoun, B.; Zhang, G. Q.

2015-05-01

Miniaturization of solid state lighting (SSL) luminaires as well as reduction of packaging and assembly costs are of prime interest for the SSL lighting industry. A novel silicon based LED package for lighting applications is presented in this paper. The proposed design consists of 5 rigid Si tiles connected by flexible polyimide hinges with embedded interconnects (ICs). Electrical, optical and thermal characteristics were taken into consideration during design. The fabrication process involved polyimide (PI) application and patterning, aluminium interconnect integration in the flexible hinge, LED reflector cavity formation and metalization followed by through wafer DRIE etching for chip formation and release. A method to connect chip front to backside without TSVs was also integrated into the process. Post-fabrication wafer level assembly included LED mounting and wirebond, phosphor-based colour conversion and silicone encapsulation. The package formation was finalized by vacuum assisted wrapping around an assembly structure to form a 3D geometry, which is beneficial for omnidirectional lighting. Bending tests were performed on the flexible ICs and optical performance at different temperatures was evaluated. It is suggested that 3D packages can be expanded to platforms for miniaturized luminaire applications by combining monolithic silicon integration and system-in-package (SiP) technologies.

Characterization of Emissions from Open Burning of Meals ...

EPA Pesticide Factsheets

Emissions from burning current and candidate Meals Ready-to-Eat (MRE) packaging and shipping containers were characterized in an effort to assuage concerns that combustive disposal of waste at forward operating bases could pose an environmental or inhalation threat. Four types of container materials, both box and liners, including the currently used fiberboard, new corrugated fiberboard with Spektrakote polymer, new fiberboard without Spektrakote polymer, and the current fiberboard without wet strength were burned in an open burn test facility that simulated the burn pit disposal methods in Iraq and Afghanistan. MREs, including both current and proposed packaging materials, were added to a single container type to examine their effect on emissions. One quarter of the food was left in the packaging to represent unused meal components. The proposed packaging, consisting of a nano-composite polymer, was added in 25 % increments compared to traditional MRE packaging to create a range of usage levels. Emission factors, mass of pollutant per mass of burned material, were increased over the emission factors of the package containers themselves by the addition of the multi-component MREs, with the exception of Volatile Organic Compounds (VOCs). In general, little distinction was observed when comparing emission factors from the four container materials and when comparing the four MRE compositions. The majority of Particulate Matter (PM) emissions were of particles that

Facies remolding in allochthonous chalk packages, Ekofisk and Albuskjell fields, North Sea

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lutz, S.J.; Ekdale, A.A.

1990-05-01

The Ekofish and Albuskjell fields in the Central Graben of the North Sea produce hydrocarbons from resedimented chalk reservoirs. Although the allochthonous nature of chalk in these fields has been recognized, the correlations of, and association between, allochthonous units has not been described. Core analysis of the Tor Formation (Maastrichtian) and the Ekofish Formation (Danian) reveals that slump deposits have been remolded into debris flows, ooze flows, and turbidites. Packages of allochthonous sediment were deposited in slope and base-of-slope environments. Two kinds of allochthonous packages occur. One package, 1-3-m thick, consists of a basal debris flow overlain by an oozemore » flow. The other package, 10-20-m thick, contains three units: a basal debris flow, an intermediate slump, and an overlying turbidite. Deposition of each type of package probably resulted from a single triggering event. Lateral changes in facies (increased convolution and decreased clastic content) and in type of deposit (slump or debris flow to ooze flow) within the packages resulted from differing degrees of deformation as the packages moved downslope. An increase in occurrence and angularity of chalk intraclasts, and in thickness of slump units from the Albuskjell field eastward to the Ekofisk field, suggest that the graben-bounding Hidra fault zone (about 30 km away) is the source of the allochthonous deposits. Vertical changes in the type of allochthonous package (from debris and ooze flows upward to slumps and turbidites) reflect decreasing topographic relief along the fault escarpment as the graben filled. This model of vertical (basin shallowing) and lateral (downslope) facies changes allows correlation of allochthonous chalk units, which are excellent hydrocarbon reservoirs.« less

Dissuasive cigarette sticks: the next step in standardised ('plain') packaging?

PubMed

Hoek, Janet; Gendall, Philip; Eckert, Christine; Louviere, Jordan

2016-11-01

Standardised (or 'plain') packaging has reduced the appeal of smoking by removing imagery that smokers use to affiliate themselves with the brand they smoke. We examined whether changing the appearance of cigarette sticks could further denormalise smoking and enhance the negative impact of standardised packaging. We conducted an online study of 313 New Zealand smokers who comprised a Best-Worst Choice experiment and a rating task. The Best-Worst experiment used a 2×3×3×6 orthogonal design to test the following attributes: on-pack warning message, branding level, warning size and stick appearance. We identified three segments whose members' choice patterns were strongly influenced by the stick design, warning theme and size, and warning theme, respectively. Each of the dissuasive sticks tested was less preferred and rated as less appealing than the most common stick in use; a 'minutes of life lost' stick was the most aversive of the stimuli tested. Dissuasive sticks could enhance the effect of standardised packaging, particularly among older smokers who are often more heavily addicted and resistant to change. Countries introducing standardised packaging legislation should take the opportunity to denormalise the appearance of cigarette sticks, in addition to removing external tobacco branding from packs and increasing the warning size. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/.

Residual strain sensor using Al-packaged optical fiber and Brillouin optical correlation domain analysis.

PubMed

Choi, Bo-Hun; Kwon, Il-Bum

2015-03-09

We propose a distributed residual strain sensor that uses an Al-packaged optical fiber for the first time. The residual strain which causes Brillouin frequency shifts in the optical fiber was measured using Brillouin optical correlation domain analysis with 2 cm spatial resolution. We quantified the Brillouin frequency shifts in the Al-packaged optical fiber by the tensile stress and compared them for a varying number of Al layers in the optical fiber. The Brillouin frequency shift of an optical fiber with one Al layer had a slope of 0.038 MHz/με with respect to tensile stress, which corresponds to 78% of that for an optical fiber without Al layers. After removal of the stress, 87% of the strain remained as residual strain. When different tensile stresses were randomly applied, the strain caused by the highest stress was the only one detected as residual strain. The residual strain was repeatedly measured for a time span of nine months for the purpose of reliability testing, and there was no change in the strain except for a 4% reduction, which is within the error tolerance of the experiment. A composite material plate equipped with our proposed Al-packaged optical fiber sensor was hammered for impact experiment and the residual strain in the plate was successfully detected. We suggest that the Al-packaged optical fiber can be adapted as a distributed strain sensor for smart structures, including aerospace structures.

Technical Review Report for the Model 9978-96 Package Safety Analysis Report for Packaging (S-SARP-G-00002, Revision 1, March 2009)

DOE Office of Scientific and Technical Information (OSTI.GOV)

West, M

2009-03-06

This Technical Review Report (TRR) documents the review, performed by Lawrence Livermore National Laboratory (LLNL) Staff, at the request of the Department of Energy (DOE), on the 'Safety Analysis Report for Packaging (SARP), Model 9978 B(M)F-96', Revision 1, March 2009 (S-SARP-G-00002). The Model 9978 Package complies with 10 CFR 71, and with 'Regulations for the Safe Transport of Radioactive Material-1996 Edition (As Amended, 2000)-Safety Requirements', International Atomic Energy Agency (IAEA) Safety Standards Series No. TS-R-1. The Model 9978 Packaging is designed, analyzed, fabricated, and tested in accordance with Section III of the American Society of Mechanical Engineers Boiler and Pressuremore » Vessel Code (ASME B&PVC). The review presented in this TRR was performed using the methods outlined in Revision 3 of the DOE's 'Packaging Review Guide (PRG) for Reviewing Safety Analysis Reports for Packages'. The format of the SARP follows that specified in Revision 2 of the Nuclear Regulatory Commission's Regulatory Guide 7.9, i.e., 'Standard Format and Content of Part 71 Applications for Approval of Packages for Radioactive Material'. Although the two documents are similar in their content, they are not identical. Formatting differences have been noted in this TRR, where appropriate. The Model 9978 Packaging is a single containment package, using a 5-inch containment vessel (5CV). It uses a nominal 35-gallon drum package design. In comparison, the Model 9977 Packaging uses a 6-inch containment vessel (6CV). The Model 9977 and Model 9978 Packagings were developed concurrently, and they were referred to as the General Purpose Fissile Material Package, Version 1 (GPFP). Both packagings use General Plastics FR-3716 polyurethane foam as insulation and as impact limiters. The 5CV is used as the Primary Containment Vessel (PCV) in the Model 9975-96 Packaging. The Model 9975-96 Packaging also has the 6CV as its Secondary Containment Vessel (SCV). In comparison, the Model 9975 Packagings use Celotex{trademark} for insulation and as impact limiters. To provide a historical perspective, it is noted that the Model 9975-96 Packaging is a 35-gallon drum package design that has evolved from a family of packages designed by DOE contractors at the Savannah River Site. Earlier package designs, i.e., the Model 9965, the Model 9966, the Model 9967, and the Model 9968 Packagings, were originally designed and certified in the early 1980s. In the 1990s, updated package designs that incorporated design features consistent with the then-newer safety requirements were proposed. The updated package designs at the time were the Model 9972, the Model 9973, the Model 9974, and the Model 9975 Packagings, respectively. The Model 9975 Package was certified by the Packaging Certification Program, under the Office of Safety Management and Operations. The Model 9978 Package has six Content Envelopes: C.1 ({sup 238}Pu Heat Sources), C.2 ( Pu/U Metals), C.3 (Pu/U Oxides, Reserved), C.4 (U Metal or Alloy), C.5 (U Compounds), and C.6 (Samples and Sources). Per 10 CFR 71.59 (Code of Federal Regulations), the value of N is 50 for the Model 9978 Package leading to a Criticality Safety Index (CSI) of 1.0. The Transport Index (TI), based on dose rate, is calculated to be a maximum of 4.1.« less

Signal processing of anthropometric data

NASA Astrophysics Data System (ADS)

Zimmermann, W. J.

1983-09-01

The Anthropometric Measurements Laboratory has accumulated a large body of data from a number of previous experiments. The data is very noisy, therefore it requires the application of some signal processing schemes. Moreover, it was not regarded as time series measurements but as positional information; hence, the data is stored as coordinate points as defined by the motion of the human body. The accumulated data defines two groups or classes. Some of the data was collected from an experiment designed to measure the flexibility of the limbs, referred to as radial movement. The remaining data was collected from experiments designed to determine the surface of the reach envelope. An interactive signal processing package was designed and implemented. Since the data does not include time this package does not include a time series element. Presently the results is restricted to processing data obtained from those experiments designed to measure flexibility.

Signal processing of anthropometric data

NASA Technical Reports Server (NTRS)

Zimmermann, W. J.

1983-01-01

The Anthropometric Measurements Laboratory has accumulated a large body of data from a number of previous experiments. The data is very noisy, therefore it requires the application of some signal processing schemes. Moreover, it was not regarded as time series measurements but as positional information; hence, the data is stored as coordinate points as defined by the motion of the human body. The accumulated data defines two groups or classes. Some of the data was collected from an experiment designed to measure the flexibility of the limbs, referred to as radial movement. The remaining data was collected from experiments designed to determine the surface of the reach envelope. An interactive signal processing package was designed and implemented. Since the data does not include time this package does not include a time series element. Presently the results is restricted to processing data obtained from those experiments designed to measure flexibility.

CSP Manufacturing Challenges and Assembly Reliability

NASA Technical Reports Server (NTRS)

Ghaffarian, Reza

2000-01-01

Although the expression of CSP is widely used by industry from suppliers to users, its implied definition had evolved as the technology has matured. There are "expert definition"- package that is up to 1.5 time die- or "interim definition". CSPs are miniature new packages that industry is starting to implement and there are many unresolved technical issues associated with their implementation. For example, in early 1997, packages with 1 mm pitch and lower were the dominant CSPs, whereas in early 1998 packages with 0.8 mm and lower became the norm for CSPs. Other changes included the use of flip chip die rather than wire bond in CSP. Nonetheless the emerging CSPs are competing with bare die assemblies and are becoming the package of choice for size reduction applications. These packages provide the benefits of small size and performance of the bare die or flip chip, with the advantage of standard die packages. The JPL-led MicrotypeBGA Consortium of enterprises representing government agencies and private companies have jointed together to pool in-kind resources for developing the quality and reliability of chip scale packages (CSPs) for a variety of projects. This talk will cover specifically the experience of our consortium on technology implementation challenges, including design and build of both standard and microvia boards, assembly of two types of test vehicles, and the most current environmental thermal cycling test results.

Alumina Based 500 C Electronic Packaging Systems and Future Development

NASA Technical Reports Server (NTRS)

Chen, Liang-Yu

2012-01-01

NASA space and aeronautical missions for probing the inner solar planets as well as for in situ monitoring and control of next-generation aeronautical engines require high-temperature environment operable sensors and electronics. A 96% aluminum oxide and Au thick-film metallization based packaging system including chip-level packages, printed circuit board, and edge-connector is in development for high temperature SiC electronics. An electronic packaging system based on this material system was successfully tested and demonstrated with SiC electronics at 500 C for over 10,000 hours in laboratory conditions previously. In addition to the tests in laboratory environments, this packaging system has more recently been tested with a SiC junction field effect transistor (JFET) on low earth orbit through the NASA Materials on the International Space Station Experiment 7 (MISSE7). A SiC JFET with a packaging system composed of a 96% alumina chip-level package and an alumina printed circuit board mounted on a data acquisition circuit board was launched as a part of the MISSE7 suite to International Space Station via a Shuttle mission and tested on the orbit for eighteen months. A summary of results of tests in both laboratory and space environments will be presented. The future development of alumina based high temperature packaging using co-fired material systems for improved performance at high temperature and more feasible mass production will also be discussed.

The Effect of Epoxy Molding Compound Floor Life to Reliability Performance and mold ability for QFN Package

NASA Astrophysics Data System (ADS)

Peanpunga, Udom; Ugsornrat, Kessararat; Thorlor, Panakamol; Sumithpibul, Chalermsak

2017-09-01

This research studied about an epoxy molding compound (EMC) floor life to reliability performance of integrated circuit (IC) package. Molding is the process for protecting the die of IC package form mechanical and chemical reaction from external environment by shaping EMC. From normal manufacturing process, the EMC is stored in the frozen at 5oC and left at around room temperature for aging time or floor life before molding process. The EMC floor life effect to its properties and reliability performance of IC package. Therefore, this work interested in varied the floor life of EMC before molding process to analyze properties of EMC such as spiral flow length, gelation time, and viscosity. In experiment, the floor life of EMC was varied to check the effect of its property to reliability performance. The EMC floor life were varied from 0 hours to 60 hours with a step of 12 hours and observed wire sweep, incomplete EMC, and delamination inside the packages for 3x3, 5x5 and 8x8 mm2 of QFN packages. The evaluation showed about clearly effect of EMC floor life to IC packaging reliability. EMC floor life is not any concern for EMC property, moldabilty, and reliability from 0 hours to 48 hours for molding process of 3x3,5x5 and 8x8 mm2 QFN packaging manufacturing

A generic multibody simulation

NASA Technical Reports Server (NTRS)

Hopping, K. A.; Kohn, W.

1986-01-01

Described is a dynamic simulation package which can be configured for orbital test scenarios involving multiple bodies. The rotational and translational state integration methods are selectable for each individual body and may be changed during a run if necessary. Characteristics of the bodies are determined by assigning components consisting of mass properties, forces, and moments, which are the outputs of user-defined environmental models. Generic model implementation is facilitated by a transformation processor which performs coordinate frame inversions. Transformations are defined in the initialization file as part of the simulation configuration. The simulation package includes an initialization processor, which consists of a command line preprocessor, a general purpose grammar, and a syntax scanner. These permit specifications of the bodies, their interrelationships, and their initial states in a format that is not dependent on a particular test scenario.

Plasma diagnostics package. Volume 2: Spacelab 2 section. Part B: Thesis projects

NASA Technical Reports Server (NTRS)

Pickett, Jolene S. (Compiler); Frank, L. A. (Compiler); Kurth, W. S. (Compiler)

1988-01-01

This volume (2), which consists of two parts (A and B), of the Plasma Diagnostics Package (PDP) Final Science Report contains a summary of all of the data reduction and scientific analyses which were performed using PDP data obtained on STS-51F as a part of the Spacelab 2 (SL-2) payload. This work was performed during the period of launch, July 29, 1985, through June 30, 1988. During this period the primary data reduction effort consisted of processing summary plots of the data received by 12 of the 14 instruments located on the PDP and submitting these data to the National Space Science Data Center (NSSDC). Three Master's and three Ph.D. theses were written using PDP instrumentation data. These theses are listed in Volume 2, Part B.

DOE Office of Scientific and Technical Information (OSTI.GOV)

SADE is a software package for rapidly assembling analytic pipelines to manipulate data. The packages consists of the engine that manages the data and coordinates the movement of data between the tasks performing a function? a set of core libraries consisting of plugins that perform common tasks? and a framework to extend the system supporting the development of new plugins. Currently through configuration files, a pipeline can be defined that maps the routing of data through a series of plugins. Pipelines can be run in a batch mode or can process streaming data? they can be executed from the commandmore » line or run through a Windows background service. There currently exists over a hundred plugins, over fifty pipeline configurations? and the software is now being used by about a half-dozen projects.« less

NASA-DoD Lead-Free Electronics Project

NASA Technical Reports Server (NTRS)

Kessel, Kurt R.

2009-01-01

In response to concerns about risks from lead-free induced faults to high reliability products, NASA has initiated a multi-year project to provide manufacturers and users with data to clarify the risks of lead-free materials in their products. The project will also be of interest to component manufacturers supplying to high reliability markets. The project was launched in November 2006. The primary technical objective of the project is to undertake comprehensive testing to generate information on failure modes/criteria to better understand the reliability of: - Packages (e.g., TSOP, BOA, PDIP) assembled and reworked with solder interconnects consisting of lead-free alloys - Packages (e.g., TSOP, BOA, PDIP) assembled and reworked with solder interconnects consisting of mixed alloys, lead component finish/lead-free solder and lead-free component finish/SnPb solder.

NASA-DoD Lead-Free Electronics Project

NASA Technical Reports Server (NTRS)

Kessel, Kurt R.

2009-01-01

In response to concerns about risks from lead-free induced faults to high reliability products, NASA has initiated a multi-year project to provide manufacturers and users with data to clarify the risks of lead-free materials in their products. The project will also be of interest to component manufacturers supplying to high reliability markets. The project was launched in November 2006. The primary technical objective of the project is to undertake comprehensive testing to generate information on failure modes/criteria to better understand the reliability of: - Packages (e.g., TSOP, BGA, PDIP) assembled and reworked with solder interconnects consisting of lead-free alloys - Packages (e.g., TSOP, BGA, PDIP) assembled and reworked with solder interconnects consisting of mixed alloys, lead component finish/lead-free solder and lead-free component finish/SnPb solder.

Examining the Influence of the Wine Festival Experience on Tourists' Quality of Life

ERIC Educational Resources Information Center

Kruger, Stefan; Rootenberg, Cindy; Ellis, Suria

2013-01-01

Hosting events and festivals is the best way of providing the wine tourism experience. Wine festivals offer a wide range of experiences that are different from day-to-day living, offer a lifestyle package and are an indicator of lifestyle tourism experience. Tourists travel to wine festivals for wine and other leisure-related experiences,…

Importance of gravity for plant growth and behavior

NASA Technical Reports Server (NTRS)

Brown, A. H.

1984-01-01

Accomplishments during the past fiscal year consisted of (1) completion of research on a study of the kinetics of damping out of circummutation when the axially directed g-force was abruptly eliminated (Research Task NULYRL). (2) Further experiments were accomplished on a comprehensive study, underway for several years, to validate (or invalidate) the use of clinostat rotation as a hypogravity simulation device. (3) Some of our earlier (unpublished) observations on plant seedlings resistance to g-loading were evaluated, interpreted, and a paper was submitted for publication (Research Task HYGEFF). (4) In what has been called ""Shuttle middeck locker ecology" an attempt to acquire reliable empirical information on the thermal profile experienced by test packages housed in middeck lockers (MDDL) during shuttle flights at long last seems to be yielding some results.

Stackfile Database

NASA Technical Reports Server (NTRS)

deVarvalho, Robert; Desai, Shailen D.; Haines, Bruce J.; Kruizinga, Gerhard L.; Gilmer, Christopher

2013-01-01

This software provides storage retrieval and analysis functionality for managing satellite altimetry data. It improves the efficiency and analysis capabilities of existing database software with improved flexibility and documentation. It offers flexibility in the type of data that can be stored. There is efficient retrieval either across the spatial domain or the time domain. Built-in analysis tools are provided for frequently performed altimetry tasks. This software package is used for storing and manipulating satellite measurement data. It was developed with a focus on handling the requirements of repeat-track altimetry missions such as Topex and Jason. It was, however, designed to work with a wide variety of satellite measurement data [e.g., Gravity Recovery And Climate Experiment -- GRACE). The software consists of several command-line tools for importing, retrieving, and analyzing satellite measurement data.

Seismic reading taken at MSC recording impact of Apollo 13 S-IVB with surface

NASA Technical Reports Server (NTRS)

1970-01-01

A seismic reading taken from instruments at the Manned Spacecraft Center (MSC) recording impact of the Apollo 13 S-IVB/Instrument Unit with lunar surface. The expended Saturn third stage and instrument unit impacted the lunar surface at 7:09 p.m., April 14, 1970. The location of the impact was 2.4 degrees south latitude and 27.9 degrees west longitude, about 76 nautical miles west-northwest of the Apollo 12 Lunar Surface Experiment package deployment site. The S-IVB/IU impact was picked up by the Passive Seismic Experiment, a component of the package and transmitted to instruments at the Mission Control Center.

Kassiopeia: a modern, extensible C++ particle tracking package

DOE Office of Scientific and Technical Information (OSTI.GOV)

Furse, Daniel; Groh, Stefan; Trost, Nikolaus

The Kassiopeia particle tracking framework is an object-oriented software package using modern C++ techniques, written originally to meet the needs of the KATRIN collaboration. Kassiopeia features a new algorithmic paradigm for particle tracking simulations which targets experiments containing complex geometries and electromagnetic fields, with high priority put on calculation efficiency, customizability, extensibility, and ease-of-use for novice programmers. To solve Kassiopeia's target physics problem the software is capable of simulating particle trajectories governed by arbitrarily complex differential equations of motion, continuous physics processes that may in part be modeled as terms perturbing that equation of motion, stochastic processes that occur inmore » flight such as bulk scattering and decay, and stochastic surface processes occurring at interfaces, including transmission and reflection effects. This entire set of computations takes place against the backdrop of a rich geometry package which serves a variety of roles, including initialization of electromagnetic field simulations and the support of state-dependent algorithm-swapping and behavioral changes as a particle's state evolves. Thanks to the very general approach taken by Kassiopeia it can be used by other experiments facing similar challenges when calculating particle trajectories in electromagnetic fields. It is publicly available at https://github.com/KATRIN-Experiment/Kassiopeia.« less

Kassiopeia: a modern, extensible C++ particle tracking package

DOE PAGES

Furse, Daniel; Groh, Stefan; Trost, Nikolaus; ...

2017-05-16

The Kassiopeia particle tracking framework is an object-oriented software package using modern C++ techniques, written originally to meet the needs of the KATRIN collaboration. Kassiopeia features a new algorithmic paradigm for particle tracking simulations which targets experiments containing complex geometries and electromagnetic fields, with high priority put on calculation efficiency, customizability, extensibility, and ease-of-use for novice programmers. To solve Kassiopeia's target physics problem the software is capable of simulating particle trajectories governed by arbitrarily complex differential equations of motion, continuous physics processes that may in part be modeled as terms perturbing that equation of motion, stochastic processes that occur inmore » flight such as bulk scattering and decay, and stochastic surface processes occurring at interfaces, including transmission and reflection effects. This entire set of computations takes place against the backdrop of a rich geometry package which serves a variety of roles, including initialization of electromagnetic field simulations and the support of state-dependent algorithm-swapping and behavioral changes as a particle's state evolves. Thanks to the very general approach taken by Kassiopeia it can be used by other experiments facing similar challenges when calculating particle trajectories in electromagnetic fields. It is publicly available at https://github.com/KATRIN-Experiment/Kassiopeia.« less

Kassiopeia: a modern, extensible C++ particle tracking package

NASA Astrophysics Data System (ADS)

Furse, Daniel; Groh, Stefan; Trost, Nikolaus; Babutzka, Martin; Barrett, John P.; Behrens, Jan; Buzinsky, Nicholas; Corona, Thomas; Enomoto, Sanshiro; Erhard, Moritz; Formaggio, Joseph A.; Glück, Ferenc; Harms, Fabian; Heizmann, Florian; Hilk, Daniel; Käfer, Wolfgang; Kleesiek, Marco; Leiber, Benjamin; Mertens, Susanne; Oblath, Noah S.; Renschler, Pascal; Schwarz, Johannes; Slocum, Penny L.; Wandkowsky, Nancy; Wierman, Kevin; Zacher, Michael

2017-05-01

The Kassiopeia particle tracking framework is an object-oriented software package using modern C++ techniques, written originally to meet the needs of the KATRIN collaboration. Kassiopeia features a new algorithmic paradigm for particle tracking simulations which targets experiments containing complex geometries and electromagnetic fields, with high priority put on calculation efficiency, customizability, extensibility, and ease-of-use for novice programmers. To solve Kassiopeia's target physics problem the software is capable of simulating particle trajectories governed by arbitrarily complex differential equations of motion, continuous physics processes that may in part be modeled as terms perturbing that equation of motion, stochastic processes that occur in flight such as bulk scattering and decay, and stochastic surface processes occurring at interfaces, including transmission and reflection effects. This entire set of computations takes place against the backdrop of a rich geometry package which serves a variety of roles, including initialization of electromagnetic field simulations and the support of state-dependent algorithm-swapping and behavioral changes as a particle’s state evolves. Thanks to the very general approach taken by Kassiopeia it can be used by other experiments facing similar challenges when calculating particle trajectories in electromagnetic fields. It is publicly available at https://github.com/KATRIN-Experiment/Kassiopeia.

The effectiveness of triclosan-incorporated plastic against bacteria on beef surfaces.

PubMed

Cutter, C N

1999-05-01

Triclosan is a nonionic, broad-spectrum, antimicrobial agent that has been incorporated into a variety of personal hygiene products, including hand soaps, deodorants, shower gels, mouthwashes, and toothpastes. In this study, plastic containing 1,500 ppm of triclosan was evaluated in plate overlay assays and meat experiments as a means of reducing populations of bacteria. Plate overlay assays indicated that the triclosan-incorporated plastic (TIP) inhibited the following organisms: Brochothrix thermosphacta ATCC 11509, Salmonella Typhimurium ATCC 14028, Staphylococcus aureus ATCC 12598, Bacillus subtilis ATCC 6051, Shigella flexneri ATCC 12022, Escherichia coli ATCC 25922, and several strains of E. coli O157:H7. In meat experiment 1, irradiated, lean beef surfaces inoculated with B. thermosphacta, Salmonella Typhimurium, E. coli O157:H7, or B. subtilis were covered with TIP, vacuum packaged, and stored for 24 h at 4 degrees C. Of the organisms tested, only populations of B. thermosphacta were slightly reduced. In meat experiment 2, prerigor beef surfaces were inoculated with E. coli O157: H7, Salmonella Typhimurium, or B. thermosphacta incubated at 4 degrees C for 24 h, wrapped in TIP or control plastic, vacuum packaged, and stored at 4 degrees C for up to 14 days. There was a slight reduction in the population of the organisms after initial application with TIP. However, bacterial populations following long-term, refrigerated (4 degrees C), vacuum-packaged storage up to 14 days were not statistically (P< or =0.05) or numerically different than controls. In meat experiment 3, even TIP-wrapped, vacuum-packaged beef samples that were temperature abused at 12 degrees C did not exhibit significant (P< or =0.05) or sustainable reductions after 14 days of 4 degrees C storage. Another study indicated that populations of E. coli O157:H7 or B. thermosphacta added directly to TIP were not affected after 2 h of refrigerated storage or that the antimicrobial activity could be extracted from the plastic. Additional experiments suggest that presence of fatty acids or adipose may diminish the antimicrobial activity of TIP on meat surfaces. This study demonstrates that while antimicrobial activity is detected against bacterial cultures in antimicrobial plate assays, plastic containing 1,500 ppm of triclosan does not effectively reduce bacterial populations on refrigerated, vacuum-packaged meat surfaces.

Transient desorption of water vapor - A potential source of error in upper atmosphere rocket experiments

NASA Technical Reports Server (NTRS)

Kendall, B. R. F.; Weeks, J. O.

1974-01-01

Results of measurements of the outgassing rates of samples of materials and surface finishes used on the outer skins of rocket-borne experiment packages in simulated rocket ascents. The results showed outgassing rates for anodized aluminum in the second minute of flight which are two to three orders of magnitude higher than those given in typical tables of outgassing rates. The measured rates for aluminum with chromate conversion surface coatings were also abnormally high. These abnormally high initial rates fell quickly after about five to ten minutes to values comparable with those in the published literature. It is concluded that anodized and chromate conversion coatings on the aluminum outer surfaces of a sounding rocket experiment package will cause gross distortion of the true water vapor environment.

Refurbishment of the cryogenic coolers for the Skylab earth resources experiment package

NASA Technical Reports Server (NTRS)

Smithson, J. C.; Luksa, N. C.

1975-01-01

Skylab Earth Resources Experiment Package (EREP) experiments, S191 and S192, required a cold temperature reference for operation of a spectrometer. This cold temperature reference was provided by a subminiature Stirling cycle cooler. However, the failure of the cooler to pass the qualification test made it necessary for additional cooler development, refurbishment, and qualification. A description of the failures and the cause of these failures for each of the coolers is presented. The solutions to the various failure modes are discussed along with problems which arose during the refurbishment program. The rationale and results of various tests are presented. The successful completion of the cryogenic cooler refurbishment program resulted in four of these coolers being flown on Skylab. The system operation during the flight is presented.

Does the Australasian "Health Star Rating" Front of Pack Nutritional Label System Work?

PubMed

Hamlin, Robert; McNeill, Lisa

2016-06-01

This article describes an experiment to measure the impact of the Australasian "Health Star Rating" front of pack nutritional label system on consumer choice behaviour. This system presents a one-half to five star rating of nutritional quality via the front facings of food product packages. While this system has been recently rolled out across Australasia, no test of its impact on food choice has been conducted. A sample of 1200 consumers was recruited on exit from supermarkets in New Zealand. A 2 × 2 factorial design was used with two levels of cold cereal product nutritional status (high, five star/low, two star) and two levels of the Health Star Rating label (present/absent). The dependent variable was revealed choice behaviour. The results indicated that the presence of the label had a significant depressive effect on consumer preference, but that this impact was not moderated in any way by the nutritional status expressed by the label. The result represents a significant functional failure of the Health Star Rating label in this research environment. The nature of the failure is consistent with the consumers processing the label in much the same way as the nominal brand cues that dominate the retail food packaging.

Easily extensible unix software for spectral analysis, display, modification, and synthesis of musical sounds

NASA Astrophysics Data System (ADS)

Beauchamp, James W.

2002-11-01

Software has been developed which enables users to perform time-varying spectral analysis of individual musical tones or successions of them and to perform further processing of the data. The package, called sndan, is freely available in source code, uses EPS graphics for display, and is written in ansi c for ease of code modification and extension. Two analyzers, a fixed-filter-bank phase vocoder (''pvan'') and a frequency-tracking analyzer (''mqan'') constitute the analysis front end of the package. While pvan's output consists of continuous amplitudes and frequencies of harmonics, mqan produces disjoint ''tracks.'' However, another program extracts a fundamental frequency and separates harmonics from the tracks, resulting in a continuous harmonic output. ''monan'' is a program used to display harmonic data in a variety of formats, perform various spectral modifications, and perform additive resynthesis of the harmonic partials, including possible pitch-shifting and time-scaling. Sounds can also be synthesized according to a musical score using a companion synthesis language, Music 4C. Several other programs in the sndan suite can be used for specialized tasks, such as signal display and editing. Applications of the software include producing specialized sounds for music compositions or psychoacoustic experiments or as a basis for developing new synthesis algorithms.

Does the Australasian “Health Star Rating” Front of Pack Nutritional Label System Work?

PubMed Central

Hamlin, Robert; McNeill, Lisa

2016-01-01

This article describes an experiment to measure the impact of the Australasian “Health Star Rating” front of pack nutritional label system on consumer choice behaviour. This system presents a one-half to five star rating of nutritional quality via the front facings of food product packages. While this system has been recently rolled out across Australasia, no test of its impact on food choice has been conducted. A sample of 1200 consumers was recruited on exit from supermarkets in New Zealand. A 2 × 2 factorial design was used with two levels of cold cereal product nutritional status (high, five star/low, two star) and two levels of the Health Star Rating label (present/absent). The dependent variable was revealed choice behaviour. The results indicated that the presence of the label had a significant depressive effect on consumer preference, but that this impact was not moderated in any way by the nutritional status expressed by the label. The result represents a significant functional failure of the Health Star Rating label in this research environment. The nature of the failure is consistent with the consumers processing the label in much the same way as the nominal brand cues that dominate the retail food packaging. PMID:27258305

Real time in vivo imaging and measurement of serine protease activity in the mouse hippocampus using a dedicated complementary metal-oxide semiconductor imaging device.

PubMed

Ng, David C; Tamura, Hideki; Tokuda, Takashi; Yamamoto, Akio; Matsuo, Masamichi; Nunoshita, Masahiro; Ishikawa, Yasuyuki; Shiosaka, Sadao; Ohta, Jun

2006-09-30

The aim of the present study is to demonstrate the application of complementary metal-oxide semiconductor (CMOS) imaging technology for studying the mouse brain. By using a dedicated CMOS image sensor, we have successfully imaged and measured brain serine protease activity in vivo, in real-time, and for an extended period of time. We have developed a biofluorescence imaging device by packaging the CMOS image sensor which enabled on-chip imaging configuration. In this configuration, no optics are required whereby an excitation filter is applied onto the sensor to replace the filter cube block found in conventional fluorescence microscopes. The fully packaged device measures 350 microm thick x 2.7 mm wide, consists of an array of 176 x 144 pixels, and is small enough for measurement inside a single hemisphere of the mouse brain, while still providing sufficient imaging resolution. In the experiment, intraperitoneally injected kainic acid induced upregulation of serine protease activity in the brain. These events were captured in real time by imaging and measuring the fluorescence from a fluorogenic substrate that detected this activity. The entire device, which weighs less than 1% of the body weight of the mouse, holds promise for studying freely moving animals.

An examination of product packaging marketing strategies used to promote pediatric multivitamins.

PubMed

Ethan, Danna; Basch, Corey H; Samuel, Lalitha; Quinn, Christine; Dunne, Stephanie

2015-06-01

The purpose of this study was to describe the nature of marketing strategies for multivitamin and multimineral (MVM) supplement packaging and to assess the extent to which these supplements are marketed as food products. A cross-sectional study of children's supplement packaging was conducted. Descriptive statistics identified common marketing practices. Websites of the three largest retail chain pharmacies in the United States and MVM manufacturers were accessed. The study's sample consisted of packaging for 52 children's MVM supplements. Child-targeted marketing included reference to trademarked characters on 42.3% of MVM packaging (n = 22). More than 80% of the sample (n = 42) listed fruity flavors and almost all packaging included descriptive words related to the MVMs' shape and/or flavor (88.5%, n = 46). Nearly one-fifth of the packaging (n = 10) pictured a food item. With respect to parent-targeted promotional language, almost 83% of the supplement packages (n = 43) included text on the support of bodily structure/function. More than half of the sample (53.8%, n = 28) had promotional language related to dietary practice (e.g. organic, gluten-free). Pediatricians can play a role in ensuring that parents are aware of (1) possible risks associated with MVM overconsumption, and (2) the importance of deriving vitamins and minerals from a balanced diet. Given the high number of exposures to pediatric MVMs among youth and established influence of food marketing on shaping children's perceptions and behaviors, further research is necessary to determine the extent to which children's MVMs are marketed as a food product and perceived as such by children.

The influence of product packaging on young people's palatability rating for RTDS and other alcoholic beverages.

PubMed

Gates, Peter; Copeland, Jan; Stevenson, Richard J; Dillon, Paul

2007-01-01

To investigate the influence of product packaging of ready to drink (RTD), or pre-mixed drinks, and other alcoholic and non-alcoholic beverages on the palatability ratings of adolescents and adults. Respondents were interviewed at their own schools or a campus of the University of NSW. The experiment tested palatability ratings in blind and non-blind conditions with a selection of 12- to 30-year-old Australians (140 adolescents and 210 adults) from seven private schools across NSW and students from the University of NSW and Macquarie University. Beverage palatability was measured utilizing an interval ratio scale from 1 to 7 before and after packaging was presented. Views on whether the beverage packaging was designed to appeal to the participant were also analysed. In general, the alcoholic beverage packaging was thought to be designed to appeal more to adults and palatability ratings significantly increased in the non-blind conditions. In contrast, the Bacardi Breezer packaging was especially palatable to younger participants. Although most alcoholic beverage packaging was not of particular appeal to adolescents, some RTD beverages may be appealing more to adolescents. Unlike other alcoholic products, the difference in palatability ratings for the Bacardi Breezer, from blind to non-blind conditions, was greater for younger participants.

Thermal Testing and Quality Assurance of BGA LCC & QFN Electronic Packages

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kuper, Cameron Mathias

The purpose of this project is to experimentally validate the thermal fatigue life of solder interconnects for a variety of surface mount electronic packages. Over the years, there has been a significant amount of research and analysis in the fracture of solder joints on printed circuit boards. Solder is important in the mechanical and electronic functionality of the component. It is important throughout the life of the product that the solder remains crack and fracture free. The specific type of solder used in this experiment is a 63Sn37Pb eutectic alloy. Each package was surrounded conformal coating or underfill material.

Tests of spool models for DNA packaging in phage lambda.

PubMed

Widom, J; Baldwin, R L

1983-12-25

Experiments are reported which bear on two spool models proposed for packaging the DNA of phage lambda. Both spool models fill an assumed spherical cavity with DNA wrapped in cylindrical or quasi-cylindrical layers composed of adjacent circular turns. In the curved-spool model, a single continuous segment of DNA, about 20% of the DNA length and probably located near the left end of the DNA, is in contact with the coat protein of the phage capsid. In the straight spool model, there are several DNA segments in contact with the capsid; they are concentrated in one half (probably the left half) of lambda DNA. We have identified the loci on the DNA which are in contact with the capsid by chemical crosslinking, induced by ultraviolet-irradiation of phage containing 5-bromodeoxyuridine in place of thymine. In an electron microscope experiment, phage are first lysed with EDTA, and then spread in a cytochrome c film by the formamide method. The disrupted capsid, which has the appearance of a phage ghost, serves as a marker showing where the DNA is crosslinked to the coat. The left end of the DNA is not distinguished from the right end, and so the map of DNA-capsid contacts is folded over on itself. Contacts are found nearly randomly over the entire map. In a second experiment, DNA from lysed, crosslinked phage is cut either with EcoRI or HindIII restriction endonucleases and the cut restriction fragments are labeled at their ends with 32P. Density centrifugation in a CsCl gradient separates free DNA from restriction fragments crosslinked to protein. After digestion with proteinase k, the DNA fragments previously crosslinked to protein are identified by size after agarose gel electrophoresis. DNA fragments from all parts of the genome are found. These two experiments show that, if the DNA of each phage is packaged identically, then the curved-spool model is ruled out and the straight spool model is unlikely. Alternatively, the manner of packaging the DNA may vary from one phage to the next. These results agree with other recent experiments on lambda DNA packaging by Hall & Schellman (1982a,b), and by Haas et al. (1982). A different experiment is also reported. The psoralen derivative aminomethyltrioxalen (AMT) is allowed to intercalate into lambda phage and then the DNA strands are crosslinked by ultraviolet-irradiation after the rapid phase of AMT intercalation is complete. The DNA is subsequently denatured by glyoxal modification and spread for electron microscopy in a cytochrome c film by the formamide method.(ABSTRACT TRUNCATED AT 400 WORDS)

A laser communication experiment utilizing the ACT satellite and an airborne laser transceiver

NASA Technical Reports Server (NTRS)

Provencher, Charles E., Jr.; Spence, Rodney L.

1988-01-01

The launch of a laser communication transmitter package into geosynchronous Earth orbit onboard the Advanced Communications Technology Satellite (ACTS) will present an excellent opportunity for the experimental reception of laser communication signals transmitted from a space orbit. The ACTS laser package includes both a heterodyne transmitter (Lincoln Labs design) and a direct detection transmitter (Goddard Space Flight Center design) with both sharing some common optical components. NASA Lewis Research Center's Space Electronics Division is planning to perform a space communication experiment utilizing the GSFC direct detection laser transceiver. The laser receiver will be installed within an aircraft provided with a glass port for the reception of the signal. This paper describes the experiment and the approach to performing such an experiment. Described are the constraints placed on the NASA Lewis experiment by the performance parameters of the laser transmitter and by the ACTS spacecraft operations. The conceptual design of the receiving terminal is given; also included is the anticipated capability of the detector.

Effect of Nisin's Controlled Release on Microbial Growth as Modeled for Micrococcus luteus.

PubMed

Balasubramanian, Aishwarya; Lee, Dong Sun; Chikindas, Michael L; Yam, Kit L

2011-06-01

The need for safe food products has motivated food scientists and industry to find novel technologies for antimicrobial delivery for improving food safety and quality. Controlled release packaging is a novel technology that uses the package to deliver antimicrobials in a controlled manner and sustain antimicrobial stress on the targeted microorganism over the required shelf life. This work studied the effect of controlled release of nisin to inhibit growth of Micrococcus luteus (a model microorganism) using a computerized syringe pump system to mimic the release of nisin from packaging films which was characterized by an initially fast rate and a slower rate as time progressed. The results show that controlled release of nisin was strikingly more effective than instantly added ("formulated") nisin. While instant addition experiments achieved microbial inhibition only at the beginning, controlled release experiments achieved complete microbial inhibition for a longer time, even when as little as 15% of the amount of nisin was used as compared to instant addition.

PDS Lunar Data Node Restoration of Apollo In-Situ Surface Data

NASA Technical Reports Server (NTRS)

Williams, David R.; Hills, H. Kent; Guinness, Edward A.; Lowman, Paul D.; Taylor, Patrick T.

2010-01-01

The Apollo missions between 1969 and 1972 deployed scientific instruments on the Moon's surface which made in-situ measurements of the lunar environment. Apollo II had the short-term Early Apollo Surface Experiments Package (EASEP) and Apollos 12, 14, 15, 16, and 17 each set up an Apollo Lunar Surface Experiments Package (ALSEP). Each ALSEP package contained a different suite of instruments which took measurements and radioed the results back to Earth over periods from 5 to 7 years until they were turned off on 30 September 1977. To this day the ALSEP data remain the only long-term in-situ information on the Moon's surface environment. The Lunar Data Node (LDN) has been formed under the auspices of the Planetary Data System (PDS) Geosciences Node to put relevant, scientifically important Apollo data into accessible digital form for use by researchers and mission planners. We will report on progress made since last year and plans for future data restorations.

From reads to genes to pathways: differential expression analysis of RNA-Seq experiments using Rsubread and the edgeR quasi-likelihood pipeline.

PubMed

Chen, Yunshun; Lun, Aaron T L; Smyth, Gordon K

2016-01-01

In recent years, RNA sequencing (RNA-seq) has become a very widely used technology for profiling gene expression. One of the most common aims of RNA-seq profiling is to identify genes or molecular pathways that are differentially expressed (DE) between two or more biological conditions. This article demonstrates a computational workflow for the detection of DE genes and pathways from RNA-seq data by providing a complete analysis of an RNA-seq experiment profiling epithelial cell subsets in the mouse mammary gland. The workflow uses R software packages from the open-source Bioconductor project and covers all steps of the analysis pipeline, including alignment of read sequences, data exploration, differential expression analysis, visualization and pathway analysis. Read alignment and count quantification is conducted using the Rsubread package and the statistical analyses are performed using the edgeR package. The differential expression analysis uses the quasi-likelihood functionality of edgeR.

Quantarctica: A Unique, Open, Standalone GIS Package for Antarctic Research and Education

NASA Astrophysics Data System (ADS)

Roth, George; Matsuoka, Kenichi; Skoglund, Anders; Melvær, Yngve; Tronstad, Stein

2017-04-01

The Norwegian Polar Institute has developed Quantarctica (http://quantarctica.npolar.no), an open GIS package for use by the international Antarctic community. Quantarctica includes a wide range of cartographic basemap layers, geophysical and glaciological datasets, and satellite imagery in standardized open file formats with a consistent Antarctic map projection and customized layer and labeling styles for quick, effective cartography. Quantarctica's strengths as an open science platform lie in 1) The complete, ready-to-use data package which includes full-resolution, original-quality vector and raster data, 2) A policy for freely-redistributable and modifiable data including all metadata and citations, and 3) QGIS, a free, full-featured, modular, offline-capable open-source GIS suite with a rapid and active development and support community. The Quantarctica team is actively incorporating more up-to-date, peer-reviewed, freely distributable pan-Antarctic geospatial datasets for the next version release in 2017. As part of this ongoing development, we are investigating the best approaches for quickly and seamlessly distributing new and updated data to users, storing datasets in efficient, open file formats while maintaining full data integrity, and coexisting with numerous online data portals in a way that most actively benefits the Antarctic community. A recent survey of Quantarctica users showed broad geographical adoption among Antarctic Treaty countries, including those outside the large US and UK Antarctic programs. Maps and figures produced by Quantarctica have also appeared in open-access journals and outside of the formal scientific community on popular science and GIS blogs. Our experience with the Quantarctica project has shown the tremendous value of education and outreach, not only in promoting open software, data formats, and practices, but in empowering Antarctic science groups to more effectively use GIS and geospatial data. Open practices are making a huge impact in Antarctic GIS, where individual countries have historically maintained their own restricted Antarctic geodatabases and where the next generation of scientists are entering the field with experience in using geospatial thinking for planning, visualization, and problem solving.

HP3 on ExoMars - Cutting airbag cloths with the sharp tip of a mechanical mole

NASA Astrophysics Data System (ADS)

Krause, C.; Izzo, M.; Re, E.; Mehls, C.; Richter, L.; Coste, P.

2009-04-01

The HP3 - Heat Flow and Physical Properties Package - is planned to be one of the Humboldt lander-based instruments on the ESA ExoMars mission. HP3 will allow the measurement of the subsurface temperature gradient and physical as well as thermophysical properties of the subsurface regolith of Mars down to a depth of 5 meters. From these measurements, the planetary heat flux can be inferred. The HP³ instrument package consists of a mole trailing a package of thermal and electrical sensors into the regolith. Beside the payload elements Thermal Excitation and Measurement Suite and a Permittivity Probe the HP3 experiment includes sensors to detect the forward motion and the tilt of the HP3 payload compartment. The HP3 experiment will be integrated into the lander platform of the ExoMars mission. The original accommodation featured a deployment device or a robotic arm to place HP3 onto the soil outside the deflated lander airbags. To avoid adding such deployment devices, it was suggested that the HP3 mole should be capable of piercing the airbags under the lander. The ExoMars lander airbag is made of 4 Kevlar layers (2 abrasive and 2 bladders). A double fold of the airbag (a worst case) would represent a pile of 12 layers. An exploratory study has examined the possibility of piercing airbag cloths by adding sharp cutting blades on the tip of a penetrating mole. In the experimental setup representative layers were laid over a Mars soil simulant. Initial tests used a hammer-driven cutting tip and had moderate to poor results. More representative tests used a prototype of the HP3 mole and were fully successful: the default 4 layer configuration was pierced as well as the 12 layer configuration, the latter one within 3 hours and about 3000 mole strokes This improved behaviour is attributed to the use of representative test hardware where guidance and suppression of mole recoil were concerned. The presentation will provide an explanation of the technical requirements on airbag cutting with a mole and the mentioned experimental setup and results.

A convenient and adaptable package of DNA sequence analysis programs for microcomputers.

PubMed Central

Pustell, J; Kafatos, F C

1982-01-01

We describe a package of DNA data handling and analysis programs designed for microcomputers. The package is convenient for immediate use by persons with little or no computer experience, and has been optimized by trial in our group for a year. By typing a single command, the user enters a system which asks questions or gives instructions in English. The system will enter, alter, and manage sequence files or a restriction enzyme library. It generates the reverse complement, translates, calculates codon usage, finds restriction sites, finds homologies with various degrees of mismatch, and graphs amino acid composition or base frequencies. A number of options for data handling and printing can be used to produce figures for publication. The package will be available in ANSI Standard FORTRAN for use with virtually any FORTRAN compiler. PMID:6278412

Tobacco industry argues domestic trademark laws and international treaties preclude cigarette health warning labels, despite consistent legal advice that the argument is invalid.

PubMed

Crosbie, Eric; Glantz, Stanton A

2014-05-01

To analyse the tobacco industry's use of international trade agreements to oppose policies to strengthen health warning labels (HWLs). A review of tobacco industry documents, tobacco control legislation and international treaties. During the early 1990s, the tobacco industry became increasingly alarmed about the advancement of HWLs on cigarettes packages. In response, it requested legal opinions from British American Tobacco's law firms in Australia and England, Britain's Department of Trade and Industry and the World Intellectual Property Organisation on the legality of restricting and prohibiting the use of their trademarks, as embodied in cigarette packages. The consistent legal advice, privately submitted to the companies, was that international treaties do not shield trademark owners from government limitations (including prohibition) on the use of their trademarks. Despite receiving this legal advice, the companies publicly argued that requiring large HWLs compromised their trademark rights under international treaties. The companies successfully used these arguments as part of their successful effort to deter Canadian and Australian governments from enacting laws requiring the plan packaging of cigarettes, which helped delay large graphic HWLs, including 'plain' packaging, for over a decade. Governments should not be intimidated by tobacco company threats and unsubstantiated claims, and carefully craft HWL laws to withstand the inevitable tobacco industry lawsuits with the knowledge that the companies' own lawyers as well as authoritative bodies have told the companies that the rights they claim do not exist.

Application of the Linux cluster for exhaustive window haplotype analysis using the FBAT and Unphased programs.

PubMed

Mishima, Hiroyuki; Lidral, Andrew C; Ni, Jun

2008-05-28

Genetic association studies have been used to map disease-causing genes. A newly introduced statistical method, called exhaustive haplotype association study, analyzes genetic information consisting of different numbers and combinations of DNA sequence variations along a chromosome. Such studies involve a large number of statistical calculations and subsequently high computing power. It is possible to develop parallel algorithms and codes to perform the calculations on a high performance computing (HPC) system. However, most existing commonly-used statistic packages for genetic studies are non-parallel versions. Alternatively, one may use the cutting-edge technology of grid computing and its packages to conduct non-parallel genetic statistical packages on a centralized HPC system or distributed computing systems. In this paper, we report the utilization of a queuing scheduler built on the Grid Engine and run on a Rocks Linux cluster for our genetic statistical studies. Analysis of both consecutive and combinational window haplotypes was conducted by the FBAT (Laird et al., 2000) and Unphased (Dudbridge, 2003) programs. The dataset consisted of 26 loci from 277 extended families (1484 persons). Using the Rocks Linux cluster with 22 compute-nodes, FBAT jobs performed about 14.4-15.9 times faster, while Unphased jobs performed 1.1-18.6 times faster compared to the accumulated computation duration. Execution of exhaustive haplotype analysis using non-parallel software packages on a Linux-based system is an effective and efficient approach in terms of cost and performance.

Application of the Linux cluster for exhaustive window haplotype analysis using the FBAT and Unphased programs

PubMed Central

Mishima, Hiroyuki; Lidral, Andrew C; Ni, Jun

2008-01-01

Background Genetic association studies have been used to map disease-causing genes. A newly introduced statistical method, called exhaustive haplotype association study, analyzes genetic information consisting of different numbers and combinations of DNA sequence variations along a chromosome. Such studies involve a large number of statistical calculations and subsequently high computing power. It is possible to develop parallel algorithms and codes to perform the calculations on a high performance computing (HPC) system. However, most existing commonly-used statistic packages for genetic studies are non-parallel versions. Alternatively, one may use the cutting-edge technology of grid computing and its packages to conduct non-parallel genetic statistical packages on a centralized HPC system or distributed computing systems. In this paper, we report the utilization of a queuing scheduler built on the Grid Engine and run on a Rocks Linux cluster for our genetic statistical studies. Results Analysis of both consecutive and combinational window haplotypes was conducted by the FBAT (Laird et al., 2000) and Unphased (Dudbridge, 2003) programs. The dataset consisted of 26 loci from 277 extended families (1484 persons). Using the Rocks Linux cluster with 22 compute-nodes, FBAT jobs performed about 14.4–15.9 times faster, while Unphased jobs performed 1.1–18.6 times faster compared to the accumulated computation duration. Conclusion Execution of exhaustive haplotype analysis using non-parallel software packages on a Linux-based system is an effective and efficient approach in terms of cost and performance. PMID:18541045

Molecular interactions and residues involved in force generation in the T4 viral DNA packaging motor.

PubMed

Migliori, Amy D; Smith, Douglas E; Arya, Gaurav

2014-12-12

Many viruses utilize molecular motors to package their genomes into preformed capsids. A striking feature of these motors is their ability to generate large forces to drive DNA translocation against entropic, electrostatic, and bending forces resisting DNA confinement. A model based on recently resolved structures of the bacteriophage T4 motor protein gp17 suggests that this motor generates large forces by undergoing a conformational change from an extended to a compact state. This transition is proposed to be driven by electrostatic interactions between complementarily charged residues across the interface between the N- and C-terminal domains of gp17. Here we use atomistic molecular dynamics simulations to investigate in detail the molecular interactions and residues involved in such a compaction transition of gp17. We find that although electrostatic interactions between charged residues contribute significantly to the overall free energy change of compaction, interactions mediated by the uncharged residues are equally if not more important. We identify five charged residues and six uncharged residues at the interface that play a dominant role in the compaction transition and also reveal salt bridging, van der Waals, and solvent hydrogen-bonding interactions mediated by these residues in stabilizing the compact form of gp17. The formation of a salt bridge between Glu309 and Arg494 is found to be particularly crucial, consistent with experiments showing complete abrogation in packaging upon Glu309Lys mutation. The computed contributions of several other residues are also found to correlate well with single-molecule measurements of impairments in DNA translocation activity caused by site-directed mutations. Copyright © 2014 Elsevier Ltd. All rights reserved.

Effect of modified atmosphere and vacuum packaging on TVB-N production of rainbow trout (Oncorhynchus mykiss) and carp (Cyprinus carpio) cuts

NASA Astrophysics Data System (ADS)

Babić Milijašević, J.; Milijašević, M.; Đinović-Stojanović, J.; Vranić, D.

2017-09-01

The aim of our research was to examine the influence of packaging in modified atmosphere and vacuum on the total volatile basic nitrogen (TVB-N) content in muscle of rainbow trout (Oncorhynchus mykiss) and common carp (Cyprinus carpio), as well as to determine the most suitable gas mixtures for packing of these freshwater species. Three sample groups of trout and carp cuts were investigated. The two groups were packaged in modified atmosphere with different gas ratios: 90%CO2+10%N2 (MAP 1) and 60%CO2+40%N2 (MAP 2), whereas the third group of fish cuts were vacuum packaged. During trials, the trout and carp cuts were stored in refrigerator at 3°C±0.5°C. Determination of TVB-N was performed on 1, 4, 7, 9, 12 and 14 days of storage. The obtained results indicate that the investigated mixtures of gases and vacuum had a significant influence on the values of TVB-N in trout and carp cuts. The lowest increase in TVB-N was established in trout and carp cuts packaged in MAP 1, whereas the highest increase was established in vacuum packaged cuts. Based on the obtained results, it can be concluded that the gas mixture consisting of 90% CO2 and 10% N2 was the most suitable for packaging of fresh trout and carp cuts in terms of TVB-N value.

[Research on Insufficient Information for Pharmaceutical Products].

PubMed

Tomita, Takashi

2017-01-01

 Several issues concerning medicines remain unclear, including the availability of known, but not easily recognizable information. This review evaluates the mechanisms of side effects and the various risk indications included in package inserts. The results can be summarized as follows. 1) Short-term exposure to gatifloxacin significantly induced insulin secretion and increased the cytosolic Ca 2+ concentration of islet cells by augmenting extracellular Ca 2+ influx and its release from the endoplasmic reticulum. Alternatively, there was a decline in the cellular insulin level and reactivity to sulfonylurea after prolonged exposure. The insulin depletion was greater than that produced by other fluoroquinolones. 2) The elution of di(2-ethylhexyl)phthalate (DEHP) from the infusion set could be associated with the solubilizers in the injection medicines. The package inserts of several products containing polysorbate or ethanol had no warning about DEHP. Although there was a slight correlation between polysorbate content and descriptions on package inserts, the use of DEHP-containing devices was prohibited for some products, even with limited amounts of polysorbate. Therefore, the package insert statements should be reviewed to reflect appropriately the extent of DEHP elution. 3) Risk management plan consists of strategies to minimize the potential risks of medicines. One approach could be to introduce reminders on package inserts; however, of 268 potential risks associated with 81 products, 56 were not mentioned in package inserts. Because most postmarketing pharmacovigilance plans depend on spontaneous reporting by healthcare personnel, the descriptions on package inserts should be reexamined.

A small and efficient dimerization/packaging signal of rat VL30 RNA and its use in murine leukemia virus-VL30-derived vectors for gene transfer.

PubMed

Torrent, C; Gabus, C; Darlix, J L

1994-02-01

Retroviral genomes consist of two identical RNA molecules associated at their 5' ends by the dimer linkage structure located in the packaging element (Psi or E) necessary for RNA dimerization in vitro and packaging in vivo. In murine leukemia virus (MLV)-derived vectors designed for gene transfer, the Psi + sequence of 600 nucleotides directs the packaging of recombinant RNAs into MLV virions produced by helper cells. By using in vitro RNA dimerization as a screening system, a sequence of rat VL30 RNA located next to the 5' end of the Harvey mouse sarcoma virus genome and as small as 67 nucleotides was found to form stable dimeric RNA. In addition, a purine-rich sequence located at the 5' end of this VL30 RNA seems to be critical for RNA dimerization. When this VL30 element was extended by 107 nucleotides at its 3' end and inserted into an MLV-derived vector lacking MLV Psi +, it directed the efficient encapsidation of recombinant RNAs into MLV virions. Because this VL30 packaging signal is smaller and more efficient in packaging recombinant RNAs than the MLV Psi + and does not contain gag or glyco-gag coding sequences, its use in MLV-derived vectors should render even more unlikely recombinations which could generate replication-competent viruses. Therefore, utilization of the rat VL30 packaging sequence should improve the biological safety of MLV vectors for human gene transfer.

Antioxidant effect of an innovative active plastic film containing olive leaves extract on fresh pork meat and its evaluation by Raman spectroscopy.

PubMed

Moudache, M; Nerín, C; Colon, M; Zaidi, F

2017-08-15

An antioxidant food packaging material was developed and applied to fresh minced pork meat. The material consists of a multilayer polyethylene film in which 4 different concentrations (2%, 5%, 10%, and 15%) of olive leaves (OL) extract were immobilized in an adhesive formula used to build the multilayer. The antioxidants were not in direct contact with the meat. The packaged meat was kept at 4°C during 16days and finally analyzed by two methods: Raman spectroscopy and thiobarbituric acid reactive substances (TBARS). Raman demonstrated a higher sensitivity for antioxidant evaluation than TBARS. Color of fresh meat packaged with the active film was also measured to evaluate the shelf life of packaged meat. The results showed that active film containing natural antioxidants efficiently enhanced the stability of fresh meat against oxidation processes, thus being a promising way to extend the shelf life of fresh minced meat for about two days. Copyright © 2017. Published by Elsevier Ltd.

Connecting West Virginia fee-fishing businesses with the larger tourism market through the development of tourism package

Treesearch

Zongxiang Mei; Chad Pierskalla; Michael Shuett

2007-01-01

Thirty-five or more fee-fishing businesses in West Virginia are often characterized as small businesses, and they could benefit from connecting with larger travel packages that are more likely to attract out-of state anglers. The objectives of this study are to: (1) identify mini-market segments based on fee-fishing experiences; (2) examine how fee-fishing mini-markets...

In cell mutational interference mapping experiment (in cell MIME) identifies the 5' polyadenylation signal as a dual regulator of HIV-1 genomic RNA production and packaging.

PubMed

Smyth, Redmond P; Smith, Maureen R; Jousset, Anne-Caroline; Despons, Laurence; Laumond, Géraldine; Decoville, Thomas; Cattenoz, Pierre; Moog, Christiane; Jossinet, Fabrice; Mougel, Marylène; Paillart, Jean-Christophe; von Kleist, Max; Marquet, Roland

2018-05-18

Non-coding RNA regulatory elements are important for viral replication, making them promising targets for therapeutic intervention. However, regulatory RNA is challenging to detect and characterise using classical structure-function assays. Here, we present in cell Mutational Interference Mapping Experiment (in cell MIME) as a way to define RNA regulatory landscapes at single nucleotide resolution under native conditions. In cell MIME is based on (i) random mutation of an RNA target, (ii) expression of mutated RNA in cells, (iii) physical separation of RNA into functional and non-functional populations, and (iv) high-throughput sequencing to identify mutations affecting function. We used in cell MIME to define RNA elements within the 5' region of the HIV-1 genomic RNA (gRNA) that are important for viral replication in cells. We identified three distinct RNA motifs controlling intracellular gRNA production, and two distinct motifs required for gRNA packaging into virions. Our analysis reveals the 73AAUAAA78 polyadenylation motif within the 5' PolyA domain as a dual regulator of gRNA production and gRNA packaging, and demonstrates that a functional polyadenylation signal is required for viral packaging even though it negatively affects gRNA production.

In cell mutational interference mapping experiment (in cell MIME) identifies the 5′ polyadenylation signal as a dual regulator of HIV-1 genomic RNA production and packaging

PubMed Central

Smith, Maureen R; Jousset, Anne-Caroline; Despons, Laurence; Laumond, Géraldine; Decoville, Thomas; Cattenoz, Pierre; Moog, Christiane; Jossinet, Fabrice; Mougel, Marylène; Paillart, Jean-Christophe

2018-01-01

Abstract Non-coding RNA regulatory elements are important for viral replication, making them promising targets for therapeutic intervention. However, regulatory RNA is challenging to detect and characterise using classical structure-function assays. Here, we present in cell Mutational Interference Mapping Experiment (in cell MIME) as a way to define RNA regulatory landscapes at single nucleotide resolution under native conditions. In cell MIME is based on (i) random mutation of an RNA target, (ii) expression of mutated RNA in cells, (iii) physical separation of RNA into functional and non-functional populations, and (iv) high-throughput sequencing to identify mutations affecting function. We used in cell MIME to define RNA elements within the 5′ region of the HIV-1 genomic RNA (gRNA) that are important for viral replication in cells. We identified three distinct RNA motifs controlling intracellular gRNA production, and two distinct motifs required for gRNA packaging into virions. Our analysis reveals the 73AAUAAA78 polyadenylation motif within the 5′ PolyA domain as a dual regulator of gRNA production and gRNA packaging, and demonstrates that a functional polyadenylation signal is required for viral packaging even though it negatively affects gRNA production. PMID:29514260

Comparison of the Solubilization Properties of Polysorbate 80 and Isopropanol/Water Solvent Systems for Organic Compounds Extracted from Three Pharmaceutical Packaging Configurations.

PubMed

Zdravkovic, Steven A

2016-10-10

It has been reported that the presence of polysorbate 80 in a pharmaceutical product's formulation may increase the number and/or amount of impurities leached from materials used during its manufacture, storage, and/or administration. However, it is uncertain if/how the solubilization properties of this surfactant compare to non-surfactant solvent systems. The goal of this study is to provide insight into this area of uncertainty by comparing the solubilization properties of polysorbate 80 to those of isopropanol/water solutions while in contact with a plasticized polyvinylchloride parenteral delivery bag, a single-use type manufacturing bag, and a polypropylene bottle. These properties were determined via a binding experiment, in which a set of model compounds was introduced into the solutions, and via an extraction experiment, in which compounds were extracted from the packaging material by the solutions. In both experiments, the amount of each compound present at equilibrium was assayed to determine the extent they were solubilized by the solution from the packaging material. Results from these experiments illustrate differences in the magnitude of solubilization obtained from solutions containing polysorbate 80 as compared to those composed of isopropanol/water. However, it was also demonstrated that their solubilization properties can be linked via a mathematical model. Copyright © 2016 Elsevier B.V. All rights reserved.

ATLAS software configuration and build tool optimisation

NASA Astrophysics Data System (ADS)

Rybkin, Grigory; Atlas Collaboration

2014-06-01

ATLAS software code base is over 6 million lines organised in about 2000 packages. It makes use of some 100 external software packages, is developed by more than 400 developers and used by more than 2500 physicists from over 200 universities and laboratories in 6 continents. To meet the challenge of configuration and building of this software, the Configuration Management Tool (CMT) is used. CMT expects each package to describe its build targets, build and environment setup parameters, dependencies on other packages in a text file called requirements, and each project (group of packages) to describe its policies and dependencies on other projects in a text project file. Based on the effective set of configuration parameters read from the requirements files of dependent packages and project files, CMT commands build the packages, generate the environment for their use, or query the packages. The main focus was on build time performance that was optimised within several approaches: reduction of the number of reads of requirements files that are now read once per package by a CMT build command that generates cached requirements files for subsequent CMT build commands; introduction of more fine-grained build parallelism at package task level, i.e., dependent applications and libraries are compiled in parallel; code optimisation of CMT commands used for build; introduction of package level build parallelism, i. e., parallelise the build of independent packages. By default, CMT launches NUMBER-OF-PROCESSORS build commands in parallel. The other focus was on CMT commands optimisation in general that made them approximately 2 times faster. CMT can generate a cached requirements file for the environment setup command, which is especially useful for deployment on distributed file systems like AFS or CERN VMFS. The use of parallelism, caching and code optimisation significantly-by several times-reduced software build time, environment setup time, increased the efficiency of multi-core computing resources utilisation, and considerably improved software developer and user experience.

Crush Testing at Oak Ridge National Laboratory

DOE Office of Scientific and Technical Information (OSTI.GOV)

Feldman, Matthew R

2011-01-01

The dynamic crush test is required in the certification testing of some small Type B transportation packages. International Atomic Energy Agency regulations state that the test article must be 'subjected to a dynamic crush test by positioning the specimen on the target so as to suffer maximum damage.' Oak Ridge National Laboratory (ORNL) Transportation Technologies Group performs testing of Type B transportation packages, including the crush test, at the National Transportation Research Center in Knoxville, Tennessee (United States). This paper documents ORNL's experiences performing crush tests on several different Type B packages. ORNL has crush tested five different drum-type packagemore » designs, continuing its 60 year history of RAM package testing. A total of 26 crush tests have been performed in a wide variety of package orientations and crush plate CG alignments. In all cases, the deformation of the outer drum created by the crush test was significantly greater than the deformation damage caused by the 9 m drop test. The crush test is a highly effective means for testing structural soundness of smaller nondense Type B shipping package designs. Further regulatory guidance could alleviate the need to perform the crush test in a wide range of orientations and crush plate CG alignments.« less

Flexible Foam Protection Materials for Portable Life Support System Packaging Study

NASA Technical Reports Server (NTRS)

Tang,Henry H.; Dillon, Paul A.; Thomas, Gretchen A.

2009-01-01

This paper discusses the phase I effort in evaluating and selecting a light weight impact protection material for the Constellation Space Suit Element (CSSE) Portable Life Support System (PLSS) conceptual packaging study. A light weight material capable of holding and protecting the components inside the PLSS is required to demonstrate the viability of the flexible PLSS packaging concept. The material needs to distribute, dissipate, and absorb the impact energy of the PLSS falling on the lunar surface. It must also be robust to consistently perform over several Extravehicular Activity (EVA) missions in the extreme lunar thermal vacuum environment. This paper documents the performance requirements for selecting a foam protection material, and the methodologies for evaluating some commercial off-the-shelf (COTS) foam material candidates. It also presents the mechanical properties and impact drop tests results of the foam material candidates. The results of this study suggest that a foam based flexible protection system is a viable solution for PLSS packaging. However, additional works are needed to optimize COTS foam or to develop a composite foam system that will meet all the performance requirements for the CSSE PLSS flexible packaging.

Installation package for a domestic solar heating and hot water system

NASA Technical Reports Server (NTRS)

1978-01-01

The installation of two prototype solar heating and hot water systems is described. The systems consists of the following subsystems: solar collector, storage, control, transport, and auxiliary energy.