General relativity at 75: how right was einstein?

PubMed

Will, C M

1990-11-09

The status of experimental tests of general relativity is reviewed on the occasion of its 75th anniversary. Einstein's equivalence principle is well supported by experiments such as the Eötvös experiment, tests of special relativity, and the gravitational redshift experiment. Tests of general relativity have reached high precision, including the light deflection and the perihelion advance of Mercury, proposed by Einstein 75 years ago, and new tests such as the Shapiro time delay and the Nordtvedt effect in lunar motion. Gravitational wave damping has been detected to an accuracy of 1 percent on the basis of measurements of the binary pulsar. The status of the "fifth force" is discussed, along with the frontiers of experimental relativity, including proposals for testing relativistic gravity with advanced technology and spacecraft.

Solar Parabolic Dish Annual Technology Evaluation Report

NASA Technical Reports Server (NTRS)

1983-01-01

The activities of the JPL Solar Thermal Power Systems Parabolic Dish Project for FY 1982 are summarized. Included are discussions on designs of module development including their concentrator, receiver, and power conversion subsystems. Analyses and test results, along with progress on field tests, Small Community Experiment System development, and tests at the Parabolic Dish Test Site are also included.

Digital Fly-By-Wire Flight Control Validation Experience

NASA Technical Reports Server (NTRS)

Szalai, K. J.; Jarvis, C. R.; Krier, G. E.; Megna, V. A.; Brock, L. D.; Odonnell, R. N.

1978-01-01

The experience gained in digital fly-by-wire technology through a flight test program being conducted by the NASA Dryden Flight Research Center in an F-8C aircraft is described. The system requirements are outlined, along with the requirements for flight qualification. The system is described, including the hardware components, the aircraft installation, and the system operation. The flight qualification experience is emphasized. The qualification process included the theoretical validation of the basic design, laboratory testing of the hardware and software elements, systems level testing, and flight testing. The most productive testing was performed on an iron bird aircraft, which used the actual electronic and hydraulic hardware and a simulation of the F-8 characteristics to provide the flight environment. The iron bird was used for sensor and system redundancy management testing, failure modes and effects testing, and stress testing in many cases with the pilot in the loop. The flight test program confirmed the quality of the validation process by achieving 50 flights without a known undetected failure and with no false alarms.

LDEF electronic systems: Successes, failures, and lessons

NASA Technical Reports Server (NTRS)

Miller, Emmett; Porter, Dave; Smith, Dave; Brooks, Larry; Levorsen, Joe; Mulkey, Owen

1991-01-01

Following the Long Duration Exposure Facility (LDEF) retrieval, the Systems Special Investigation Group (SIG) participated in an extensive series of tests of various electronic systems, including the NASA provided data and initiate systems, and some experiment systems. Overall, these were found to have performed remarkably well, even though most were designed and tested under limited budgets and used at least some nonspace qualified components. However, several anomalies were observed, including a few which resulted in some loss of data. The postflight test program objectives, observations, and lessons learned from these examinations are discussed. All analyses are not yet complete, but observations to date will be summarized, including the Boeing experiment component studies and failure analysis results related to the Interstellar Gas Experiment. Based upon these observations, suggestions for avoiding similar problems on future programs are presented.

High-temperature Y267 EPDM elastomer field and laboratory experiences, September 1982

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hirasuna, Alan R.; Friese, Gilbert J.; Stephens, Clifford A.

1982-10-08

High performance elastomers were developed for hostile geothermal environments which clearly advance the state-of-the-art. The Y267 EPDM compound is eminently successful and has accumulated broad laboratory and field test experience. Over 15 separate tests are reviewed with about 95% performed independently by other organizations. The tests include a broad spectrum of environments with temperatures in excess of 320 C (608 F), differential pressures up to 138 MPa (20,000 psi) and in fluids including brine, oils, isobutane, and others.

Sequential Design of Experiments to Maximize Learning from Carbon Capture Pilot Plant Testing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Soepyan, Frits B.; Morgan, Joshua C.; Omell, Benjamin P.

Pilot plant test campaigns can be expensive and time-consuming. Therefore, it is of interest to maximize the amount of learning and the efficiency of the test campaign given the limited number of experiments that can be conducted. This work investigates the use of sequential design of experiments (SDOE) to overcome these challenges by demonstrating its usefulness for a recent solvent-based CO2 capture plant test campaign. Unlike traditional design of experiments methods, SDOE regularly uses information from ongoing experiments to determine the optimum locations in the design space for subsequent runs within the same experiment. However, there are challenges that needmore » to be addressed, including reducing the high computational burden to efficiently update the model, and the need to incorporate the methodology into a computational tool. We address these challenges by applying SDOE in combination with a software tool, the Framework for Optimization, Quantification of Uncertainty and Surrogates (FOQUS) (Miller et al., 2014a, 2016, 2017). The results of applying SDOE on a pilot plant test campaign for CO2 capture suggests that relative to traditional design of experiments methods, SDOE can more effectively reduce the uncertainty of the model, thus decreasing technical risk. Future work includes integrating SDOE into FOQUS and using SDOE to support additional large-scale pilot plant test campaigns.« less

The Development of a Pediatric Inpatient Experience of Care Measure: Child HCAHPS®

PubMed Central

Toomey, Sara L.; Zaslavsky, Alan M.; Elliott, Marc N.; Gallagher, Patricia M.; Fowler, Floyd J.; Klein, David J.; Shulman, Shanna; Ratner, Jessica; McGovern, Caitriona; LeBlanc, Jessica L.; Schuster, Mark A.

2016-01-01

CMS uses Adult HCAHPS® scores for public reporting and pay-for-performance for most U.S. hospitals, but no publicly available standardized survey of inpatient experience of care exists for pediatrics. To fill the gap, CMS/AHRQ commissioned the development of the Consumer Assessment of Healthcare Providers and Systems Hospital Survey – Child Version (Child HCAHPS), a survey of parents/guardians of pediatric patients (<18 years old) who were recently hospitalized. This Special Article describes the development of Child HCAHPS, which included an extensive review of the literature and quality measures, expert interviews, focus groups, cognitive testing, pilot testing of the draft survey, a national field test with 69 hospitals in 34 states, psychometric analysis, and end-user testing of the final survey. We conducted extensive validity and reliability testing to determine which items would be included in the final survey instrument and to develop composite measures. We analyzed national field test data from 17,727 surveys collected from 11/12-1/14 from parents of recently hospitalized children. The final Child HCAHPS instrument has 62 items, including 39 patient experience items, 10 screeners, 12 demographic/descriptive items, and 1 open-ended item. The 39 experience items are categorized based on testing into 18 composite and single-item measures. Our composite and single-item measures demonstrated good to excellent hospital-level reliability at 300 responses per hospital. Child HCAHPS was developed to be a publicly available standardized survey of pediatric inpatient experience of care. It can be used to benchmark pediatric inpatient experience across hospitals and assist in efforts to improve the quality of inpatient care. PMID:26195542

Feasibility analysis of gravitational experiments in space

NASA Technical Reports Server (NTRS)

Everitt, C. W. F.

1977-01-01

Experiments on gravitation and general relativity suggested by different workers in the past ten or more years are reviewed, their feasibility examined, and the advantages of performing them in space were studied. The experiments include: (1) the gyro relativity experiment; (2) experiments to test the equivalence of gravitational and inertial mass; (3) an experiment to look for nongeodesic motion of spinning bodies in orbit around the earth; (4) experiments to look for changes of the gravitational constant G with time; (5) a variety of suggestions; laboratory tests of experimental gravity; and (6) gravitational wave experiments.

Comparison of aerodynamic coefficients obtained from theoretical calculations wind tunnel tests and flight tests data reduction for the alpha jet aircraft

NASA Technical Reports Server (NTRS)

Guiot, R.; Wunnenberg, H.

1980-01-01

The methods by which aerodynamic coefficients are determined and discussed. These include: calculations, wind tunnel experiments and experiments in flight for various prototypes of the Alpha Jet. A comparison of obtained results shows good correlation between expectations and in-flight test results.

The F-15B Propulsion Flight Test Fixture: A New Flight Facility For Propulsion Research

NASA Technical Reports Server (NTRS)

Corda, Stephen; Vachon, M. Jake; Palumbo, Nathan; Diebler, Corey; Tseng, Ting; Ginn, Anthony; Richwine, David

2001-01-01

The design and development of the F-15B Propulsion Flight Test Fixture (PFTF), a new facility for propulsion flight research, is described. Mounted underneath an F-15B fuselage, the PFTF provides volume for experiment systems and attachment points for propulsion devices. A unique feature of the PFTF is the incorporation of a six-degree-of-freedom force balance. Three-axis forces and moments can be measured in flight for experiments mounted to the force balance. The NASA F-15B airplane is described, including its performance and capabilities as a research test bed aircraft. The detailed description of the PFTF includes the geometry, internal layout and volume, force-balance operation, available instrumentation, and allowable experiment size and weight. The aerodynamic, stability and control, and structural designs of the PFTF are discussed, including results from aerodynamic computational fluid dynamic calculations and structural analyses. Details of current and future propulsion flight experiments are discussed. Information about the integration of propulsion flight experiments is provided for the potential PFTF user.

The Psychology Experiment Building Language (PEBL) and PEBL Test Battery.

PubMed

Mueller, Shane T; Piper, Brian J

2014-01-30

We briefly describe the Psychology Experiment Building Language (PEBL), an open source software system for designing and running psychological experiments. We describe the PEBL Test Battery, a set of approximately 70 behavioral tests which can be freely used, shared, and modified. Included is a comprehensive set of past research upon which tests in the battery are based. We report the results of benchmark tests that establish the timing precision of PEBL. We consider alternatives to the PEBL system and battery tests. We conclude with a discussion of the ethical factors involved in the open source testing movement. Copyright © 2013 Elsevier B.V. All rights reserved.

The Psychology Experiment Building Language (PEBL) and PEBL Test Battery

PubMed Central

Mueller, Shane T.; Piper, Brian J.

2014-01-01

Background We briefly describe the Psychology Experiment Building Language (PEBL), an open source software system for designing and running psychological experiments. New Method We describe the PEBL test battery, a set of approximately 70 behavioral tests which can be freely used, shared, and modified. Included is a comprehensive set of past research upon which tests in the battery are based. Results We report the results of benchmark tests that establish the timing precision of PEBL. Comparison with Existing Method We consider alternatives to the PEBL system and battery tests. Conclusions We conclude with a discussion of the ethical factors involved in the open source testing movement. PMID:24269254

CRITICAL TESTS FOR PRT REACTOR

DOE Office of Scientific and Technical Information (OSTI.GOV)

Triplett, J.R.; Anderson, J.K.; Dunn, R.E.

1960-07-01

Critical teste to be performed on the Plutonium Recycle Te st Heactor are described. Exponential, approach-tocritical, critical, and substitution experiments will be carried out. These experiments include: calibration of moderator level; determination of the wori of various fuel loadings; calibration of the shim system including determination of maximum control strength of the entire system; substitution experiments to determine reflector savings, void effects, effects of H/sub 2/O and degraded D/sub 2/O coolants, and effects of loop and other material intsllations; determination of fuel-plus-coolant and moderator temperature coefficients; and kinetic experiments to determine response of the reactor to reactivity changes. (M.C.G.)

On Improving the Experiment Methodology in Pedagogical Research

ERIC Educational Resources Information Center

Horakova, Tereza; Houska, Milan

2014-01-01

The paper shows how the methodology for a pedagogical experiment can be improved through including the pre-research stage. If the experiment has the form of a test procedure, an improvement of methodology can be achieved using for example the methods of statistical and didactic analysis of tests which are traditionally used in other areas, i.e.…

Simulation of Physical Experiments in Immersive Virtual Environments

NASA Technical Reports Server (NTRS)

Noor, Ahmed K.; Wasfy, Tamer M.

2001-01-01

An object-oriented event-driven immersive Virtual environment is described for the creation of virtual labs (VLs) for simulating physical experiments. Discussion focuses on a number of aspects of the VLs, including interface devices, software objects, and various applications. The VLs interface with output devices, including immersive stereoscopic screed(s) and stereo speakers; and a variety of input devices, including body tracking (head and hands), haptic gloves, wand, joystick, mouse, microphone, and keyboard. The VL incorporates the following types of primitive software objects: interface objects, support objects, geometric entities, and finite elements. Each object encapsulates a set of properties, methods, and events that define its behavior, appearance, and functions. A container object allows grouping of several objects. Applications of the VLs include viewing the results of the physical experiment, viewing a computer simulation of the physical experiment, simulation of the experiments procedure, computational steering, and remote control of the physical experiment. In addition, the VL can be used as a risk-free (safe) environment for training. The implementation of virtual structures testing machines, virtual wind tunnels, and a virtual acoustic testing facility is described.

Test program for transmitter experiment package and heat pipe system for the communications technology satellite

NASA Technical Reports Server (NTRS)

Depauw, J. F.; Reader, K. E.; Staskus, J. V.

1976-01-01

The test program is described for the 200 watt transmitter experiment package and the variable conductance heat pipe system which are components of the high-power transponder aboard the Communications Technology Satellite. The program includes qualification tests to demonstrate design adequacy, acceptance tests to expose latent defects in flight hardware, and development tests to integrate the components into the transponder system and to demonstrate compatibility.

Design and Status of RERTR Irradiation Tests in the Advanced Test Reactor

DOE Office of Scientific and Technical Information (OSTI.GOV)

Daniel M. Wachs; Richard G. Ambrosek; Gray Chang

2006-10-01

Irradiation testing of U-Mo based fuels is the central component of the Reduced Enrichment for Research and Test Reactors (RERTR) program fuel qualification plan. Several RERTR tests have recently been completed or are planned for irradiation in the Advanced Test Reactor (ATR) located at the Idaho National Laboratory in Idaho Falls, ID. Four mini-plate experiments in various stages of completion are described in detail, including the irradiation test design, objectives, and irradiation conditions. Observations made during and after the in-reactor RERTR-7A experiment breach are summarized. The irradiation experiment design and planned irradiation conditions for full-size plate test are described. Progressmore » toward element testing will be reviewed.« less

NEVADA TEST SITE EXPERIMENTAL FARM: SUMMARY REPORT 1963-1981

EPA Science Inventory

This report summarizes the findings from experiments conducted at the Experimental Dairy Farm located on the Nevada Test Site. These experiments included the air-forage-cow-milk transport of the radioiodines, and the metabolism and milk transfer of other fission products and seve...

RERTR-12 Insertion 2 Irradiation Summary Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

D. M. Perez; G. S. Chang; D. M. Wachs

2012-09-01

The Reduced Enrichment for Research and Test Reactor (RERTR) experiment RERTR-12 was designed to provide comprehensive information on the performance of uranium-molybdenum (U-Mo) based monolithic fuels for research reactor applications.1 RERTR-12 insertion 2 includes the capsules irradiated during the last three irradiation cycles. These capsules include Z, Y1, Y2 and Y3 type capsules. The following report summarizes the life of the RERTR-12 insertion 2 experiment through end of irradiation, including as-run neutronic analysis results, thermal analysis results and hydraulic testing results.

Lorentz Invariance:. Present Experimental Status

NASA Astrophysics Data System (ADS)

Lämmerzahl, Claus

2006-02-01

Being one of the pillars of modern physics, Lorentz invariance has to be tested as precisely as possible. We review the present status of laboratory tests of Lorentz invariance. This includes the tests of properties of light propagation which are covered by the famous Michelson-Morley, Kennedy-Thorndike, and Ives-Stilwell experiments, as well as tests on dynamical properties of matter as, e.g., tests exploring the maximum velocity of massive particles or tests of the isotropy of quantum particles in Hughes-Drever experiments.

Solar parabolic dish technology evaluation report

NASA Technical Reports Server (NTRS)

Lucas, J. W.

1984-01-01

The activities of the JPL Solar Thermal Power Systems Parabolic Dish Project for FY 1983 are summarized. Included are discussions on designs of module development including concentrator, receiver, and power conversion subsystems together with a separate discussion of field tests, Small Community Experiment system development, and tests at the Parabolic Dish Test Site.

Testing effects in mixed- versus pure-list designs.

PubMed

Rowland, Christopher A; Littrell-Baez, Megan K; Sensenig, Amanda E; DeLosh, Edward L

2014-08-01

In the present study, we investigated the role of list composition in the testing effect. Across three experiments, participants learned items through study and initial testing or study and restudy. List composition was manipulated, such that tested and restudied items appeared either intermixed in the same lists (mixed lists) or in separate lists (pure lists). In Experiment 1, half of the participants received mixed lists and half received pure lists. In Experiment 2, all participants were given both mixed and pure lists. Experiment 3 followed Erlebacher's (Psychological Bulletin, 84, 212-219, 1977) method, such that mixed lists, pure tested lists, and pure restudied lists were given to independent groups. Across all three experiments, the final recall results revealed significant testing effects for both mixed and pure lists, with no reliable difference in the magnitude of the testing advantage across list designs. This finding suggests that the testing effect is not subject to a key boundary condition-list design-that impacts other memory phenomena, including the generation effect.

F-16XL-2 Supersonic Laminar Flow Control Flight Test Experiment

NASA Technical Reports Server (NTRS)

Anders, Scott G.; Fischer, Michael C.

1999-01-01

The F-16XL-2 Supersonic Laminar Flow Control Flight Test Experiment was part of the NASA High-Speed Research Program. The goal of the experiment was to demonstrate extensive laminar flow, to validate computational fluid dynamics (CFD) codes and design methodology, and to establish laminar flow control design criteria. Topics include the flight test hardware and design, airplane modification, the pressure and suction distributions achieved, the laminar flow achieved, and the data analysis and code correlation.

Laboratory Experiments with Okapi: Participation in the TREC Programme.

ERIC Educational Resources Information Center

Robertson, S. E.; And Others

1997-01-01

Summarizes the development of information retrieval evaluation ideas, describes the design of the TREC (Text Retrieval Conference) experiments, and discusses the Okapi team's participation in TREC. Highlights include the Cranfield projects that tested the principles of information retrieval system design, test collections, weighting functions,…

Skylab medical experiments altitude test crew observations.

NASA Technical Reports Server (NTRS)

Bobko, K. J.

1973-01-01

The paper deals with the crew's observations during training and the SMEAT 56-day test. Topics covered include the crew's adaptation to the SMEAT environment and medical experiments protocol. Personal observations are made of daily activities surrounding the medical experiments hardware, Skylab clothing, supplementary activities, recreational equipment, food, and waste management. An assessment of these items and their contributions to the Skylab flight program is made.

Photovoltaic array space power plus diagnostics experiment

NASA Technical Reports Server (NTRS)

Burger, D. R.

1990-01-01

The objective is to summarize the five years of hardware development and fabrication represented by the Photovoltaic Array Space Power Plus Diagnostics (PASP Plus) Instrument. The original PASP Experiment requirements and background is presented along with the modifications which were requested to transform the PASP Experiment into the PASP Plus Instrument. The PASP Plus hardware and software is described. Test results for components and subsystems are given as well as final system tests. Also included are appendices which describe the major subsystems and present supporting documentation such as block diagrams, schematics, circuit board artwork, drawings, test procedures and test reports.

RERTR-7 Irradiation Summary Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

D. M. Perez; M. A. Lillo; G. S. Chang

2011-12-01

The Reduced Enrichment for Research and Test Reactor (RERTR) experiment RERTR-7A, was designed to test several modified fuel designs to target fission densities representative of a peak low enriched uranium (LEU) burnup in excess of 90% U-235 at peak experiment power sufficient to generate a peak surface heat flux of approximately 300 W/cm2. The RERTR-7B experiment was designed as a high power test of 'second generation' dispersion fuels at peak experiment power sufficient to generate a surface heat flux on the order of 230 W/cm2.1 The following report summarizes the life of the RERTR-7A and RERTR-7B experiments through end ofmore » irradiation, including as-run neutronic analyses, thermal analyses and hydraulic testing results.« less

Accurate monitoring leads to effective control and greater learning of patient education materials.

PubMed

Rawson, Katherine A; O'Neil, Rochelle; Dunlosky, John

2011-09-01

Effective management of chronic diseases (e.g., diabetes) can depend on the extent to which patients can learn and remember disease-relevant information. In two experiments, we explored a technique motivated by theories of self-regulated learning for improving people's learning of information relevant to managing a chronic disease. Materials were passages from patient education booklets on diabetes from NIDDK. Session 1 included an initial study trial, Session 2 included self-regulated restudy, and Session 3 included a final memory test. The key manipulation concerned the kind of support provided for self-regulated learning during Session 2. In Experiment 1, participants either were prompted to self-test and then evaluate their learning before selecting passages to restudy, were shown the prompt questions but did not overtly self-test or evaluate learning prior to selecting passages, or were not shown any prompts and were simply given the menu for selecting passages to restudy. Participants who self-tested and evaluated learning during Session 2 had a small but significant advantage over the other groups on the final test. Secondary analyses provided evidence that the performance advantage may have been modest because of inaccurate monitoring. Experiment 2 included a group who also self-tested but who evaluated their learning using idea-unit judgments (i.e., by checking their responses against a list of key ideas from the correct response). Participants who self-tested and made idea-unit judgments exhibited a sizable advantage on final test performance. Secondary analyses indicated that the performance advantage was attributable in part to more accurate monitoring and more effective self-regulated learning. An important practical implication is that learning of patient education materials can be enhanced by including appropriate support for learners' self-regulatory processes. (c) 2011 APA, all rights reserved.

Final Science Reports of the US Experiments Flown on the Russian Biosatellite Cosmos 2229

NASA Technical Reports Server (NTRS)

Connolly, James P. (Editor); Skidmore, Michael G. (Editor); Helwig, Denice A. (Editor)

1997-01-01

Cosmos 2229 was launched on December 29, 1992, containing a biological payload including two young male rhesus monkeys, insects, amphibians, and cell cultures. The biosatellite was launched from the Plesetsk Cosmodrome in Russia for a mission duration of 11.5 days. The major research objectives were: (1) Study of adaptive response mechanisms of mammals during flight; and (2) Study of physiological mechanisms underlying vestibular, motor system and brain function in primates during early and later adaptation phases. American scientists and their Russian collaborators conducted 11 experiments on this mission which included extensive preflight and postflight studies with rhesus monkeys. Biosamples and data were subsequently transferred to the United States. The U.S. responsibilities for this flight included the development of experiment protocols, the fabrication of some flight instrumentation and experiment-specific ground-based hardware, the conducting of preflight and postflight testing and the analysis of biospecimens and data for the U.S. experiments. A description of the Cosmos 2229 mission is presented in this report including preflight, on-orbit and postflight activities. The flight and ground-based bioinstrumentation which was developed by the U.S. and Russia is also described, along with the associated preflight testing ot the U.S. hardware. Final Science Reports for the experiments are also included.

The role of low cognitive effort and negative symptoms in neuropsychological impairment in schizophrenia.

PubMed

Strauss, Gregory P; Morra, Lindsay F; Sullivan, Sara K; Gold, James M

2015-03-01

Two experiments were conducted to examine whether insufficient effort, negative symptoms (e.g., avolition, anhedonia), and psychological variables (e.g., anhedonia and perception of low cognitive resources) predict generalized neurocognitive impairment in individuals with schizophrenia (SZ). In Experiment 1, participants included 97 individuals with SZ and 63 healthy controls (CN) who completed the Victoria Symptom Validity Test (VSVT), the MATRICS Consensus Cognitive Battery (MCCB), and self-report anhedonia questionnaires. In Experiment 2, participants included 46 individuals with SZ and 33 CN who completed Green's Word Memory Test (WMT), the MCCB, and self-reports of anhedonia, defeatist performance beliefs, and negative expectancy appraisals. RESULTS indicated that a low proportion of individuals with SZ failed effort testing (1.0% Experiment 1; 15.2% Experiment 2); however, global neurocognitive impairment was significantly predicted by low effort and negative symptoms. Findings indicate that low effort does not threaten the validity of neuropsychological test results in the majority of individuals with schizophrenia; however, effort testing may be useful in SZ patients with severe negative symptoms who may be more likely to put forth insufficient effort due to motivational problems. Although the base rate of failure is relatively low, it may be beneficial to screen for insufficient effort in SZ and exclude individuals who fail effort testing from pharmacological or cognitive remediation trials. PsycINFO Database Record (c) 2015 APA, all rights reserved.

The accessibility of semantic knowledge for odours that can and cannot be named.

PubMed

Stevenson, Richard J; Mahmut, Mehmet K

2013-01-01

When faces, objects, or voices are encountered, naming lapses can occur, but this does not preclude knowing other specific semantic information about the nameless thing. In the experiments reported here, we examined whether this is also the case for odours, using a procedure based upon the Pyramid and Palm Trees test. In Experiment 1, participants were presented with a target odour, then two pictures, and had to pick the picture semantically associated with the target. In Experiment 2, participants were presented with a target odour, then two test odours, and again had to pick the semantically associated test stimulus. In each experiment, other tests followed, including a parallel verbal-based test, an odour-naming test, and various ratings. Neither experiment found any evidence of specific semantic knowledge about a target odour, unless the target odour name (Experiment 1) or all of the odour names (Experiment 2) were known. Additional tests suggested that these effects were independent of odour familiarity and similarity. We suggest that the absence of specific semantic information in the absence of a name may reflect poor connectivity between olfactory perceptual and semantic memory systems.

Fuel Cycle Research and Development Accident Tolerant Fuels Series 1 (ATF-1) Irradiation Testing FY 2016 Status Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Core, Gregory Matthew

This report contains a summary of irradiation testing of Fuel Cycle Research and Development (FCRD) Accident Tolerant Fuels Series 1 (ATF 1) experiments performed at Idaho National Laboratory (INL) in FY 2016. ATF 1 irradiation testing work performed in FY 2016 included design, analysis, and fabrication of ATF-1B drop in capsule ATF 1 series experiments and irradiation testing of ATF-1 capsules in the ATR.

Liquid Rocket Engine Testing

NASA Technical Reports Server (NTRS)

Rahman, Shamim

2005-01-01

Comprehensive Liquid Rocket Engine testing is essential to risk reduction for Space Flight. Test capability represents significant national investments in expertise and infrastructure. Historical experience underpins current test capabilities. Test facilities continually seek proactive alignment with national space development goals and objectives including government and commercial sectors.

Engineering study for pallet adapting the Apollo laser altimeter and photographic camera system for the Lidar Test Experiment on orbital flight tests 2 and 4

NASA Technical Reports Server (NTRS)

Kuebert, E. J.

1977-01-01

A Laser Altimeter and Mapping Camera System was included in the Apollo Lunar Orbital Experiment Missions. The backup system, never used in the Apollo Program, is available for use in the Lidar Test Experiments on the STS Orbital Flight Tests 2 and 4. Studies were performed to assess the problem associated with installation and operation of the Mapping Camera System in the STS. They were conducted on the photographic capabilities of the Mapping Camera System, its mechanical and electrical interface with the STS, documentation, operation and survivability in the expected environments, ground support equipment, test and field support.

ARL Human Factors Engineering Technology: Overview of 6.2 Efforts for Dr. Lemnios, DDRE

DTIC Science & Technology

2012-03-01

Soldier-focused Neurotechnologies . Summaries for each area include a brief description of the research, types of experiments, tests, and demonstrations...7 2.4 Soldier-focused Neurotechnologies ...focused Neurotechnologies In the research summaries, the questions posed during the review are addressed: • What types of experiments/studies/tests

MSFC Doppler Lidar Science experiments and operations plans for 1981 airborne test flight

NASA Technical Reports Server (NTRS)

Fichtl, G. H.; Bilbro, J. W.; Kaufman, J. W.

1981-01-01

The flight experiment and operations plans for the Doppler Lidar System (DLS) are provided. Application of DLS to the study of severe storms and local weather penomena is addressed. Test plans involve 66 hours of flight time. Plans also include ground based severe storm and local weather data acquisition.

Surface electrical properties experiment study phase, volume 3

NASA Technical Reports Server (NTRS)

1973-01-01

The reliability and quality assurance system and procedures used in developing test equipment for the Lunar Experiment projects are described. The subjects discussed include the following: (1) documentation control, (2) design review, (3) parts and materials selection, (4) material procurement, (5) inspection procedures, (6) qualification and special testing, and failure modes and effects analysis.

A More Powerful Test in Three-Level Cluster Randomized Designs

ERIC Educational Resources Information Center

Konstantopoulos, Spyros

2011-01-01

Field experiments that involve nested structures frequently assign treatment conditions to entire groups (such as schools). A key aspect of the design of such experiments includes knowledge of the clustering effects that are often expressed via intraclass correlation. This study provides methods for constructing a more powerful test for the…

Sodium-sulfur battery flight experiment definition study

NASA Technical Reports Server (NTRS)

Chang, Rebecca; Minck, Robert

1990-01-01

Sodium-sulfur batteries are considered to be one of the most likely battery systems for space applications. Compared with the Ni-H2 or Ni-Co battery systems, Na-S batteries offer a mass reduction by a factor of 2 to 4, representing significant launch cost savings or increased payload mass capabilities. The Na-S battery operates at between 300 and 400 C, using liquid sodium and sulfur/polysulfide electrodes and solid ceramic electrolyte; the transport of the electrode materials to the surface of the electrolyte is through wicking/capillary forces. This paper describes five tests identified for the Na-S battery flight experiment definition study, which include the cell characterization test, the reactant distribution test, the current/temperature distribution test, the freeze/thaw test, and the multicell LEO test. A schematic diagram of Na-S cell is included.

COTS Ceramic Chip Capacitors: An Evaluation of the Parts and Assurance Methodologies

NASA Technical Reports Server (NTRS)

Sampson, Michael J.

2004-01-01

This viewgraph presentation profiles an experiment to evaluate the suitability of commercial off-the-shelf (COTS) ceramic chip capacitors for NASA spaceflight applications. The experiment included: 1) Voltage Conditioning ('Burn-In'); 2) Highly Accelerated Life Test (HALT); 3) Destructive Physical Analysis (DPA); 4) Ultimate Voltage Breakdown Strength. The presentation includes results for each of the capacitors used in the experiment.

Application of IUS equipment and experience to orbit transfer vehicles of the 90's

NASA Astrophysics Data System (ADS)

Bangsund, E.; Keeney, J.; Cowgill, E.

1985-10-01

This paper relates experiences with the IUS program and the application of that experience to Future Orbit Transfer Vehicles. More specifically it includes the implementation of the U.S. Air Force Space Division high reliability parts standard (SMASO STD 73-2C) and the component/system test standard (MIL-STD-1540A). Test results from the parts and component level testing and the resulting system level test program for fourteen IUS flight vehicles are discussed. The IUS program has had the highest compliance with these standards and thus offers a benchmark of experience for future programs demanding extreme reliability. In summary, application of the stringent parts standard has resulted in fewer failures during testing and the stringent test standard has eliminated design problems in the hardware. Both have been expensive in costs and schedules, and should be applied with flexibility.

The Confrontation between General Relativity and Experiment.

PubMed

Will, Clifford M

2006-01-01

The status of experimental tests of general relativity and of theoretical frameworks for analyzing them is reviewed. Einstein's equivalence principle (EEP) is well supported by experiments such as the Eötvös experiment, tests of special relativity, and the gravitational redshift experiment. Ongoing tests of EEP and of the inverse square law are searching for new interactions arising from unification or quantum gravity. Tests of general relativity at the post-Newtonian level have reached high precision, including the light deflection, the Shapiro time delay, the perihelion advance of Mercury, and the Nordtvedt effect in lunar motion. Gravitational wave damping has been detected in an amount that agrees with general relativity to better than half a percent using the Hulse-Taylor binary pulsar, and other binary pulsar systems have yielded other tests, especially of strong-field effects. When direct observation of gravitational radiation from astrophysical sources begins, new tests of general relativity will be possible.

The Confrontation between General Relativity and Experiment.

PubMed

Will, Clifford M

2014-01-01

The status of experimental tests of general relativity and of theoretical frameworks for analyzing them is reviewed and updated. Einstein's equivalence principle (EEP) is well supported by experiments such as the Eötvös experiment, tests of local Lorentz invariance and clock experiments. Ongoing tests of EEP and of the inverse square law are searching for new interactions arising from unification or quantum gravity. Tests of general relativity at the post-Newtonian level have reached high precision, including the light deflection, the Shapiro time delay, the perihelion advance of Mercury, the Nordtvedt effect in lunar motion, and frame-dragging. Gravitational wave damping has been detected in an amount that agrees with general relativity to better than half a percent using the Hulse-Taylor binary pulsar, and a growing family of other binary pulsar systems is yielding new tests, especially of strong-field effects. Current and future tests of relativity will center on strong gravity and gravitational waves.

Development flight tests of JetStar LFC leading-edge flight test experiment

NASA Technical Reports Server (NTRS)

Fisher, David F.; Fischer, Michael C.

1987-01-01

The overall objective of the flight tests on the JetStar aircraft was to demonstrate the effectiveness and reliability of laminar flow control under representative flight conditions. One specific objective was to obtain laminar flow on the JetStar leading-edge test articles for the design and off-design conditions. Another specific objective was to obtain operational experience on a Laminar Flow Control (LFC) leading-edge system in a simulated airline service. This included operational experience with cleaning requirements, the effect of clogging, possible foreign object damage, erosion, and the effects of ice particle and cloud encounters. Results are summarized.

Identification challenges for large space structures

NASA Technical Reports Server (NTRS)

Pappa, Richard S.

1990-01-01

The paper examines the on-orbit modal identification of large space structures, stressing the importance of planning and experience, in preparation for the Space Station Structural Characterization Experiment (SSSCE) for the Space Station Freedom. The necessary information to foresee and overcome practical difficulties is considered in connection with seven key factors, including test objectives, dynamic complexity of the structure, data quality, extent of exploratory studies, availability and understanding of software tools, experience with similar problems, and pretest analytical conditions. These factors affect identification success in ground tests. Comparisons with similar ground tests of assembled systems are discussed, showing that the constraints of space tests make these factors more significant. The absence of data and experiences relating to on-orbit modal identification testing is shown to make identification a uniquely mathematical problem, although all spacecraft are constructed and verified by proven engineering methods.

ATS-F ground station integration

NASA Technical Reports Server (NTRS)

1975-01-01

The ATS ground stations were described, including a system description, operational frequencies and bandwidth, and a discussion of individual subsystems. Each station configuration is described as well as its floor plan. The station performance, as tested by the GSI, is displayed in chart form providing a summary of the more important parameters tested. This chart provides a listing of test data, by site, for comparison purposes. Also included is a description of the ATS-6 experiments, the equipment, and interfaces required to perform these experiments. The ADP subsystem and its role in the experiments is also described. A description of each program task and a summary of the activities performed were then given. These efforts were accomplished at the Rosman II Ground Station, located near Rosman N.C., the Mojave Ground Station, located near Barstow Ca., and the GSI Contractors plant located near Baltimore, Md.

Directed Design of Experiments for Validating Probability of Detection Capability of a Testing System

NASA Technical Reports Server (NTRS)

Generazio, Edward R. (Inventor)

2012-01-01

A method of validating a probability of detection (POD) testing system using directed design of experiments (DOE) includes recording an input data set of observed hit and miss or analog data for sample components as a function of size of a flaw in the components. The method also includes processing the input data set to generate an output data set having an optimal class width, assigning a case number to the output data set, and generating validation instructions based on the assigned case number. An apparatus includes a host machine for receiving the input data set from the testing system and an algorithm for executing DOE to validate the test system. The algorithm applies DOE to the input data set to determine a data set having an optimal class width, assigns a case number to that data set, and generates validation instructions based on the case number.

Space Shuttle Boundary Layer Transition Flight Experiment Ground Testing Overview

NASA Technical Reports Server (NTRS)

Berger, Karen T.; Anderson, Brian P.; Campbell, Charles H.

2014-01-01

In support of the Boundary Layer Transition (BLT) Flight Experiment (FE) Project in which a manufactured protuberance tile was installed on the port wing of Space Shuttle Orbiter Discovery for STS-119, STS- 128, STS-131 and STS-133 as well as Space Shuttle Orbiter Endeavour for STS-134, a significant ground test campaign was completed. The primary goals of the test campaign were to provide ground test data to support the planning and safety certification efforts required to fly the flight experiment as well as validation for the collected flight data. These test included Arcjet testing of the tile protuberance, aerothermal testing to determine the boundary layer transition behavior and resultant surface heating and planar laser induced fluorescence (PLIF) testing in order to gain a better understanding of the flow field characteristics associated with the flight experiment. This paper provides an overview of the BLT FE Project ground testing. High-level overviews of the facilities, models, test techniques and data are presented, along with a summary of the insights gained from each test.

Skylab Medical Experiments Altitude Test /SMEAT/ facility design and operation.

NASA Technical Reports Server (NTRS)

Hinners, A. H., Jr.; Correale, J. V.

1973-01-01

This paper presents the design approaches and test facility operation methods used to successfully accomplish a 56-day test for Skylab to permit evaluation of selected Skylab medical experiments in a ground test simulation of the Skylab environment with an astronaut crew. The systems designed for this test include the two-gas environmental control system, the fire suppression and detection system, equipment transfer lock, ground support equipment, safety systems, potable water system, waste management system, lighting and power system, television monitoring, communications and recreation systems, and food freezer.

Annual progress report on the NSRR experiments, (21)

NASA Astrophysics Data System (ADS)

1992-05-01

Fuel behavior studies under simulated reactivity-initiated accident (RIA) conditions have been performed in the Nuclear Safety Research Reactor (NSRR) since 1975. This report gives the results of experiments performed from April, 1989 through March, 1990 and discussions of them. A total of 41 tests were carried out during this period. The tests are distinguished into pre-irradiated fuel tests and fresh fuel tests; the former includes 2 JMTR pre-irradiated fuel tests, 2 PWR pre-irradiated fuel tests, and 2 BWR pre-irradiated fuel tests, and the latter includes 6 standard fuel tests (6 SP(center dot)CP scoping tests), 7 power and cooling condition parameter tests (4 flow shrouded fuel tests, 1 bundle simulation test, 1 fully water-filled vessel test, 1 high pressure/high temperature loop test), 12 special fuel tests (3 stainless steel clad fuel tests, 3 improved PWR fuel tests, 6 improved BWR fuel tests), 3 severe fuel damage tests (1 high temperature flooding test, 1 flooding behavior observation test, 1 debris coolability test), 3 fast breeder reactor fuel tests (2 moderator material characteristic measurement tests, 1 fuel behavior observation test), and 2 miscellaneous tests (2 preliminary tests for pre-irradiated fuel tests).

Retrieval enhances eyewitness suggestibility to misinformation in free and cued recall.

PubMed

Wilford, Miko M; Chan, Jason C K; Tuhn, Sam J

2014-03-01

Immediately recalling a witnessed event can increase people's susceptibility to later postevent misinformation. But this retrieval-enhanced suggestibility (RES) effect has been shown only when the initial recall test included specific questions that reappeared on the final test. Moreover, it is unclear whether this phenomenon is affected by the centrality of event details. These limitations make it difficult to generalize RES to criminal investigations, which often begin with free recall prior to more specific queries from legal officials and attorneys. In 3 experiments, we examined the influence of test formats (free recall vs. cued recall) and centrality of event details (central vs. peripheral) on RES. In Experiment 1, both the initial and final tests were cued recall. In Experiment 2, the initial test was free recall and the final test was cued recall. In Experiment 3, both the initial and final tests were free recall. Initial testing increased misinformation reporting on the final test for peripheral details in all experiments, but the effect was significant for central details only after aggregating the data from all 3 experiments. These results show that initial free recall can produce RES, and more broadly, that free recall can potentiate subsequent learning of complex prose materials. © 2013 American Psychological Association

ERTS-C (Landsat 3) cryogenic heat pipe experiment definition

NASA Technical Reports Server (NTRS)

Brennan, P. J.; Kroliczek, E. J.

1975-01-01

A flight experiment designed to demonstrate current cryogenic heat pipe technology was defined and evaluated. The experiment package developed is specifically configured for flight aboard an ERTS type spacecraft. Two types of heat pipes were included as part of the experiment package: a transporter heat pipe and a thermal diode heat pipe. Each was tested in various operating modes. Performance data obtained from the experiment are applicable to the design of cryogenic systems for detector cooling, including applications where periodic high cooler temperatures are experienced as a result of cyclic energy inputs.

Feasibility and systems definition study for Microwave Multi-Application Payload (MMAP)

NASA Technical Reports Server (NTRS)

Horton, J. B.; Allen, C. C.; Massaro, M. J.; Zemany, J. L.; Murrell, J. W.; Stanhouse, R. W.; Condon, G. P.; Stone, R. F.; Swana, J.; Afifi, M.

1977-01-01

Work completed on three Shuttle/Spacelab experiments is examined: the Adaptive Multibeam Phased Array Antenna (AMPA) Experiment, Electromagnetic Environment Experiment (EEE) and Millimeter Wave Communications Experiment (MWCE). Results included the definition of operating modes, sequence of operation, radii of operation about several ground stations, signal format, foot prints of typical orbits and preliminary definition of ground and user terminals. Conceptual hardware designs, Spacelab interfaces, data handling methods, experiment testing and verification studies were included. The MWCE-MOD I was defined conceptually for a steerable high gain antenna.

Geotechnical Centrifuge Experiments to Evaluate Piping in Foundation Soils

DTIC Science & Technology

2014-05-01

verifiable results. These tests were successful in design , construction, and execution of a realistic simulation of internal erosion leading to failure...possible “scale effects,” “modeling of models” testing protocol should be included in the test program. Also, the model design should minimize the scale...recommendations for improving the centrifuge tests include the following: • Design improved system for reservoir control to provide definitive and

The Laser Communications Relay Demonstration Experiment Program

NASA Technical Reports Server (NTRS)

Israel, Dave

2017-01-01

This paper elaborates on the Laser Communications Relay Demonstration (LCRD) Experiment Program, which will engage in a number of pre-determined experiments and also call upon a wide variety of experimenters to test new laser communications technology and techniques, and to gather valuable data. LCRD is a joint project between NASAs Goddard Space Flight Center (GSFC), the Jet Propulsion Laboratory (JPL), and the Massachusetts Institute of Technology Lincoln Laboratory (MIT LL). LCRD will test the functionality in various settings and scenarios of optical communications links from a GEO payload to ground stations in Southern California and Hawaii over a two-year period following launch in 2019. The LCRD investigator team will execute numerous experiments to test critical aspects of laser communications activities over real links and systems, collecting data on the effects of atmospheric turbulence and weather on performance and communications availability. LCRD will also incorporate emulations of target scenarios, including direct-to-Earth (DTE) links from user spacecraft and optical relay providers supporting user spacecraft. To supplement and expand upon the results of these experiments, the project also includes a Guest Experimenters Program, which encourages individuals and groups from government agencies, academia and industry to propose diverse experiment ideas.

The Laser Communications Relay Demonstration Experiment Program

NASA Technical Reports Server (NTRS)

Israel, David J.; Edwards, Bernard L.; Moores, John D.; Piazzolla, Sabino; Merritt, Scott

2017-01-01

This paper elaborates on the Laser Communications Relay Demonstration (LCRD) Experiment Program, which will engage in a number of pre-determined experiments and also call upon a wide variety of experimenters to test new laser communications technology and techniques, and to gather valuable data. LCRD is a joint project between NASA's Goddard Space Flight Center (GSFC), the Jet Propulsion Laboratory (JPL), and the Massachusetts Institute of Technology Lincoln Laboratory (MIT LL). LCRD will test the functionality in various settings and scenarios of optical communications links from a GEO (Geosynchronous Earth Orbit) payload to ground stations in Southern California and Hawaii over a two-year period following launch in 2019. The LCRD investigator team will execute numerous experiments to test critical aspects of laser communications activities over real links and systems, collecting data on the effects of atmospheric turbulence and weather on performance and communications availability. LCRD will also incorporate emulations of target scenarios, including direct-to-Earth (DTE) links from user spacecraft and optical relay providers supporting user spacecraft. To supplement and expand upon the results of these experiments, the project also includes a Guest Experimenters Program, which encourages individuals and groups from government agencies, academia and industry to propose diverse experiment ideas.

Flying Quality Analysis of a JAS 39 Gripen Ministick Controller in an F/A-18 Aircraft

NASA Technical Reports Server (NTRS)

Carter, John F.; Stoliker, P. C.

2000-01-01

NASA Dryden conducted a handling qualities experiment using a small displacement centerstick controller that Saab-Scania developed for the JAS 39 Gripen aircraft. The centerstick, or ministick, was mounted in the rear cockpit of an F/A-18 aircraft. Production support flight control computers (PSFCC) provided a pilot-selectable research control system. The objectives for this experiment included determining whether the mechanical characteristics of the centerstick controller had any significant effect on the handling qualities of the F/A-18, and determining the usefulness of the PSFCCs for this kind of experiment. Five pilots evaluated closed-loop tracking tasks, including echelon and column formation flight and target following. Cooper-Harper ratings and pilot comments were collected for each maneuver. This paper describes the test system, including the PSFCCs, the Gripen centerstick, and the flight test experiment. The paper presents results of longitudinal handling qualities maneuvers, including low order equivalent systems, Neal-Smith, and controls anticipation parameter analyses. The experiment showed that, while the centerstick controller provided a different aircraft feel, few handling qualities deficiencies resulted. It also demonstrated that the PSFCCs were useful for this kind of investigation.

A Comparison of Methods to Test for Mediation in Multisite Experiments

ERIC Educational Resources Information Center

Pituch, Keenan A.; Whittaker, Tiffany A.; Stapleton, Laura M.

2005-01-01

A Monte Carlo study extended the research of MacKinnon, Lockwood, Hoffman, West, and Sheets (2002) for single-level designs by examining the statistical performance of four methods to test for mediation in a multilevel experimental design. The design studied was a two-group experiment that was replicated across several sites, included a single…

X-24C research vehicle

NASA Technical Reports Server (NTRS)

1974-01-01

A group of experiments that might be accomplished on the X-24C research vehicle are discussed indicating in each case the technology development needed to ready the experiments for flight, and also indicating interface problems between the vehicle and the experiment. Experiments that could be cheaply done using test platforms other than the X-24C have been eliminated. Experiments that are clearly applicable only to the X-24C research vehicle are, of course, included. Experiments that might be accomplished on either the X-24C or some other platform requiring further investigation concerning proper applicability are included for consideration.

Feasibility and systems definition study for microwave multi-application payload (MMAP)

NASA Technical Reports Server (NTRS)

Horton, J. B.; Allen, C. C.; Massaro, M. J.; Zemany, J. L.; Murrell, J. W.; Stanhouse, R. W.; Condon, G. P.; Stone, R. F.

1977-01-01

There were three Shuttle/Spacelab experiments: adaptive multibeam phased array antenna (AMPA) experiment, electromagnetic environment experiment (EEE), and millimeter wave communications experiment (MWCE). Work on the AMPA experiment was completed. Results included are definition of operating modes, sequence of operation, radii of operation about several ground stations, signal format, foot prints of typical orbits and preliminary definition of ground and user terminals. Definition of the MOD I EEE included conceptual hardware designs, spacelab interfaces, preliminary data handling methods, experiment tests and verification, and EMC studies. The MWCE was defined conceptually for a steerable high gain antenna.

10 CFR 60.143 - Monitoring and testing waste packages.

Code of Federal Regulations, 2010 CFR

2010-01-01

... package monitoring program shall include laboratory experiments which focus on the internal condition of... the laboratory experiments. (d) The waste package monitoring program shall continue as long as...

10 CFR 60.143 - Monitoring and testing waste packages.

Code of Federal Regulations, 2011 CFR

2011-01-01

... package monitoring program shall include laboratory experiments which focus on the internal condition of... the laboratory experiments. (d) The waste package monitoring program shall continue as long as...

10 CFR 60.143 - Monitoring and testing waste packages.

Code of Federal Regulations, 2012 CFR

2012-01-01

... package monitoring program shall include laboratory experiments which focus on the internal condition of... the laboratory experiments. (d) The waste package monitoring program shall continue as long as...

10 CFR 60.143 - Monitoring and testing waste packages.

Code of Federal Regulations, 2013 CFR

2013-01-01

... package monitoring program shall include laboratory experiments which focus on the internal condition of... the laboratory experiments. (d) The waste package monitoring program shall continue as long as...

10 CFR 60.143 - Monitoring and testing waste packages.

Code of Federal Regulations, 2014 CFR

2014-01-01

... package monitoring program shall include laboratory experiments which focus on the internal condition of... the laboratory experiments. (d) The waste package monitoring program shall continue as long as...

Joint Acoustic Propagation Experiment (JAPE-91) Workshop

NASA Technical Reports Server (NTRS)

Willshire, William L., Jr. (Compiler); Chestnutt, David (Compiler)

1993-01-01

The Joint Acoustic Propagation Experiment (JAPE), was conducted at the White Sands Missile Range, New Mexico, USA, during the period 11-28 Jul. 1991. JAPE consisted of various short and long range propagation experiments using various acoustic sources including speakers, propane cannons, helicopters, a 155 mm howitzer, and static high explosives. Of primary importance to the performance of theses tests was the extensive characterization of the atmosphere during these tests. This atmospheric characterization included turbulence measurements. A workshop to disseminate the results of JAPE-91 was held in Hampton, VA, on 28 Apr. 1993. This report is a compilation of the presentations made at the workshop along with a list of attendees and the agenda.

CSEP-Japan: The Japanese node of the collaboratory for the study of earthquake predictability

NASA Astrophysics Data System (ADS)

Yokoi, S.; Tsuruoka, H.; Nanjo, K.; Hirata, N.

2011-12-01

Collaboratory for the Study of Earthquake Predictability (CSEP) is a global project of earthquake predictability research. The final goal of this project is to have a look for the intrinsic predictability of the earthquake rupture process through forecast testing experiments. The Earthquake Research Institute, the University of Tokyo joined the CSEP and started the Japanese testing center called as CSEP-Japan. This testing center constitutes an open access to researchers contributing earthquake forecast models for applied to Japan. A total of 91 earthquake forecast models were submitted on the prospective experiment starting from 1 November 2009. The models are separated into 4 testing classes (1 day, 3 months, 1 year and 3 years) and 3 testing regions covering an area of Japan including sea area, Japanese mainland and Kanto district. We evaluate the performance of the models in the official suite of tests defined by the CSEP. The experiments of 1-day, 3-month, 1-year and 3-year forecasting classes were implemented for 92 rounds, 4 rounds, 1round and 0 round (now in progress), respectively. The results of the 3-month class gave us new knowledge concerning statistical forecasting models. All models showed a good performance for magnitude forecasting. On the other hand, observation is hardly consistent in space-distribution with most models in some cases where many earthquakes occurred at the same spot. Throughout the experiment, it has been clarified that some properties of the CSEP's evaluation tests such as the L-test show strong correlation with the N-test. We are now processing to own (cyber-) infrastructure to support the forecast experiment as follows. (1) Japanese seismicity has changed since the 2011 Tohoku earthquake. The 3rd call for forecasting models was announced in order to promote model improvement for forecasting earthquakes after this earthquake. So, we provide Japanese seismicity catalog maintained by JMA for modelers to study how seismicity changes in Japan. (2) Now we prepare the 3-D forecasting experiment with a depth range of 0 to 100 km in Kanto region. (3) The testing center improved an evaluation system for 1-day class experiment because this testing class required fast calculation ability to finish forecasting and testing results within one day. This development will make a real-time forecasting system come true. (4) The special issue of 1st part titled Earthquake Forecast Testing Experiment in Japan was published on the Earth, Planets and Space Vol. 63, No.3, 2011 on March, 2011. This issue includes papers of algorithm of statistical models participating our experiment and outline of the experiment in Japan. The 2nd part of this issue, which is now on line, will be published soon. In this presentation, we will overview CSEP-Japan and results of the experiments, and discuss direction of our activity. An outline of the experiment and activities of the Japanese Testing Center are published on our WEB site;

Modifications to the Langley 8-foot transonic pressure tunnel for the laminar flow control experiment

NASA Technical Reports Server (NTRS)

Harris, Charles D.; Brooks, Cuyler W., Jr.

1988-01-01

Modifications to the NASA Langley 8 Foot Transonic Pressure Tunnel in support of the Lamina Flow Control (LFC) Experiment included the installation of a honeymoon and five screens in the settling chamber upstream of the test section 41-long test section liner that extended from the upstream end of the test section contraction region, through the best section, and into the diffuser. The honeycomb and screens were installed as permanent additions to the facility, and the liner was a temporary addition to be removed at the conclusion of the LFC Experiment. These modifications are briefly described.

Earth radiation budget experiment software development

NASA Technical Reports Server (NTRS)

Edmonds, W. L.

1985-01-01

Computer programming and analysis efforts were carried out in support of the Earth Radiation Budget Experiment (ERBE) at NASA/Langley. The Earth Radiation Budget Experiment is described as well as data acquisition, analysis and modeling support for the testing of ERBE instruments. Also included are descriptions of the programs developed to analyze, format and display data collected during testing of the various ERBE instruments. Listings of the major programs developed under this contract are located in an appendix.

75 FR 32426 - Notice of Proposed Information Collection Requests

Federal Register 2010, 2011, 2012, 2013, 2014

2010-06-08

..., experiments with questionnaire design, and usability testing of electronic data collection instruments... this effect include but are not limited to experiments with levels of incentives for various types of...

NASA Cold Land Processes Experiment (CLPX 2002/03): Spaceborne remote sensing

Treesearch

Robert E. Davis; Thomas H. Painter; Don Cline; Richard Armstrong; Terry Haran; Kyle McDonald; Rick Forster; Kelly Elder

2008-01-01

This paper describes satellite data collected as part of the 2002/03 Cold Land Processes Experiment (CLPX). These data include multispectral and hyperspectral optical imaging, and passive and active microwave observations of the test areas. The CLPX multispectral optical data include the Advanced Very High Resolution Radiometer (AVHRR), the Landsat Thematic Mapper/...

Experience of sexual violence among women in HIV discordant unions after voluntary HIV counselling and testing

PubMed Central

Emusu, Donath; Ivankova, Nataliya; Jolly, Pauline; Kirby, Russell; Foushee, Herman; Wabwire-Mangen, Fred; Katongole, Drake; Ehiri, John

2009-01-01

HIV-serodiscordant relationships are those in which one partner is infected with HIV while the other is not. We investigated experiences of sexual violence among women in HIV discordant unions attending HIV post-test club services in Uganda. A volunteer sample of 26 women from three AIDS Information Centres in Uganda who reported having experienced sexual violence in a larger epidemiological study were interviewed, using the qualitative critical incident technique. Data were analysed using TEXTPACK, a software application for computer-assisted content analysis. Incidents of sexual violence narrated by the women included use of physical force and verbal threats. Overall, four themes that characterise the women’s experience of sexual violence emerged from the analysis: knowledge of HIV test results, prevalence of sexual violence, vulnerability and proprietary views and reactions to sexual violence. Alcohol abuse by the male partners was an important factor in the experience of sexual violence among the women. Their experiences evoked different reactions and feelings, including concern over the need to have children, fear of infection, desire to separate from their spouses/partners, helplessness, anger and suicidal tendencies. HIV counselling and testing centres should be supported with the capacity to address issues related to sexual violence for couples who are HIV discordant. PMID:20024712

Comparison of Commercial EMI Test Techniques to NASA EMI Test Techniques

NASA Astrophysics Data System (ADS)

Smith, Valerie

2000-11-01

This systems report describes how the Optical Properties Monitor (OPM) experiment was developed. Pertinent design parameters are discussed, along with mission information and system requirements to successfully complete the mission. Environmental testing was performed on the OPM to certify it for spaceflight. This testing included vibration, thermal vacuum, electromagnetic interference and conductance, and toxicity tests. Instrument and monitor subsystem performances, including the reflectometer, vacuum ultraviolet, total integrated scatter, atomic oxygen monitor, irradiance monitor, and molecular contamination monitor during the mission are discussed. The OPM experiment was launched aboard the Space Shuttle on mission STS-81 in January 1997 and transferred to the Mir space station. An extravehicular activity (EVA) was performed in April 1997 to attach the OPM experiment to the outside of the Mir/Shuttle Docking Module for space environment exposure. The OPM conducted in situ measurements of a number of material samples. These data may be found in the OPM Science Report. OPM was retrieved during an EVA in January 1998 and was returned to Earth on board the Space Shuttle on mission STS-89.

Remarkable experiences of the nuclear tests in residents near the Semipalatinsk nuclear test site: analysis based on the questionnaire surveys.

PubMed

Kawano, Noriyuki; Ohtaki, Megu

2006-02-01

The main objective of this paper is to identify salient experiences of those who were exposed to radiation by the nuclear tests at the Semipalatinsk Nuclear Tests Site (SNTS). In 2002, our research team of the Research Institute for Radiation Biology and Medicine, Hiroshima University, started to conduct some field research by means of a questionnaire survey. Through this, we expected to examine the health condition of the residents near the SNTS, identify their experiences from the nuclear tests, and understand the exposure path. This attempt at clarifying the reality of radiation exposure at Semipalatinsk through the use of a survey research method is the first of its kind. Among the responses to our survey, the present paper focuses mainly upon responses to the questions concerning the experiences of the nuclear tests. It deals mainly with direct experiences of nuclear tests of the residents characteristic to Semipalatinsk, including some new experiences hitherto unnoticed. The present paper touches upon their concrete direct experiences of flash, bomb blast, heat, rain and dust. We also discuss distinct experiences in Semipalatinsk such as evacuation, through the additional use of their testimonies. The data have been compared with the results obtained in a similar survey made in Hiroshima and Nagasaki. For the data analysis, a statistical method called logistic multiple linear regression analysis has been used.

The Confrontation between General Relativity and Experiment.

PubMed

Will, Clifford M

2001-01-01

The status of experimental tests of general relativity and of theoretical frameworks for analysing them are reviewed. Einstein's equivalence principle (EEP) is well supported by experiments such as the Eötvös experiment, tests of special relativity, and the gravitational redshift experiment. Future tests of EEP and of the inverse square law will search for new interactions arising from unification or quantum gravity. Tests of general relativity at the post-Newtonian level have reached high precision, including the light defl ection the Shapiro time delay, the perihelion advance of Mercury, and the Nordtvedt effect in lunar motion. Gravitational wave damping has been detected in an amount that agrees with general relativity to half a percent using the Hulse-Taylor binary pulsar, and new binary pulsar systems may yield further improvements. When direct observation of gravitational radiation from astrophysical sources begins, new tests of general relativity will be possible.

Materials Laboratory Classes for First Year Undergraduates

ERIC Educational Resources Information Center

Fahy, F. W.

1975-01-01

Describes a combined demonstration and student experiment course to illustrate fundamental techniques, instrumentation, and concise report writing. Describes experiments including tensile tests, heat treatment, equilibrium diagram, microexamination, strain measurement, and recrystallization. (GH)

Multidimensional Screening as a Pharmacology Laboratory Experience.

ERIC Educational Resources Information Center

Malone, Marvin H.; And Others

1979-01-01

A multidimensional pharmacodynamic screening experiment that addresses drug interaction is included in the pharmacology-toxicology laboratory experience of pharmacy students at the University of the Pacific. The student handout with directions for the procedure is reproduced, drug compounds tested are listed, and laboratory evaluation results are…

Boiling Experiment Facility for Heat Transfer Studies in Microgravity

NASA Technical Reports Server (NTRS)

Delombard, Richard; McQuillen, John; Chao, David

2008-01-01

Pool boiling in microgravity is an area of both scientific and practical interest. By conducting tests in microgravity, it is possible to assess the effect of buoyancy on the overall boiling process and assess the relative magnitude of effects with regards to other "forces" and phenomena such as Marangoni forces, liquid momentum forces, and microlayer evaporation. The Boiling eXperiment Facility is now being built for the Microgravity Science Glovebox that will use normal perfluorohexane as a test fluid to extend the range of test conditions to include longer test durations and less liquid subcooling. Two experiments, the Microheater Array Boiling Experiment and the Nucleate Pool Boiling eXperiment will use the Boiling eXperiment Facility. The objectives of these studies are to determine the differences in local boiling heat transfer mechanisms in microgravity and normal gravity from nucleate boiling, through critical heat flux and into the transition boiling regime and to examine the bubble nucleation, growth, departure and coalescence processes. Custom-designed heaters will be utilized to achieve these objectives.

The NASA Langley Laminar-Flow-Control (LFC) experiment on a swept, supercritical airfoil: Design overview

NASA Technical Reports Server (NTRS)

Harris, Charles D.; Harvey, William D.; Brooks, Cuyler W., Jr.

1988-01-01

A large-chord, swept, supercritical, laminar-flow-control (LFC) airfoil was designed and constructed and is currently undergoing tests in the Langley 8 ft Transonic Pressure Tunnel. The experiment was directed toward evaluating the compatibility of LFC and supercritical airfoils, validating prediction techniques, and generating a data base for future transport airfoil design as part of NASA's ongoing research program to significantly reduce drag and increase aircraft efficiency. Unique features of the airfoil included a high design Mach number with shock free flow and boundary layer control by suction. Special requirements for the experiment included modifications to the wind tunnel to achieve the necessary flow quality and contouring of the test section walls to simulate free air flow about a swept model at transonic speeds. Design of the airfoil with a slotted suction surface, the suction system, and modifications to the tunnel to meet test requirements are discussed.

RERTR-6 Irradiation Summary Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

D. M. Perez; M. A. Lillo; G. S. Chang

2011-12-01

The Reduced Enrichment for Research and Test Reactor (RERTR) experiment RERTR-6 was designed to evaluate several modified fuel designs that were proposed to address the possibility of breakaway swelling due to porosity within the (U. Mo) Al interaction product observed in the full-size plate tests performed in Russia and France1. The following report summarizes the life of the RERTR-6 experiment through end of irradiation, including as-run neutronic analyses, thermal analyses and hydraulic testing results.

RERTR-8 Irradiation Summary Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

D. M. Perez; M. A. Lillo; G. S. Chang

2011-12-01

The Reduced Enrichment for Research and Test Reactor (RERTR) experiment RERTR-8, was designed to test monolithic mini-fuel plates fabricated via hot isostatic pressing (HIP), the effect of molybdenum (Mo) content on the monolithic fuel behavior, and the efficiency of ternary additions to dispersion fuel particles on the interaction layer behavior at higher burnup. The following report summarizes the life of the RERTR-8 experiment through end of irradiation, including as-run neutronic analysis, thermal analysis and hydraulic testing results.

Near-term lander experiments for growing plants on Mars: requirements for information on chemical and physical properties of Mars regolith.

PubMed

Schuerger, Andrew C; Ming, Douglas W; Newsom, Horton E; Ferl, Robert J; McKay, Christopher P

2002-01-01

In order to support humans for long-duration missions to Mars, bioregenerative Advanced Life Support (ALS) systems have been proposed that would use higher plants as the primary candidates for photosynthesis. Hydroponic technologies have been suggested as the primary method of plant production in ALS systems, but the use of Mars regolith as a plant growth medium may have several advantages over hydroponic systems. The advantages for using Mars regolith include the likely bioavailability of plant-essential ions, mechanical support for plants, and easy access of the material once on the surface. We propose that plant biology experiments must be included in near-term Mars lander missions in order to begin defining the optimum approach for growing plants on Mars. Second, we discuss a range of soil chemistry and soil physics tests that must be conducted prior to, or in concert with, a plant biology experiment in order to properly interpret the results of plant growth studies in Mars regolith. The recommended chemical tests include measurements on soil pH, electrical conductivity and soluble salts, redox potential, bioavailability of essential plant nutrients, and bioavailability of phytotoxic elements. In addition, a future plant growth experiment should include procedures for determining the buffering and leaching requirements of Mars regolith prior to planting. Soil physical tests useful for plant biology studies in Mars regolith include bulk density, particle size distribution, porosity, water retention, and hydraulic conductivity.

Near-term lander experiments for growing plants on Mars: requirements for information on chemical and physical properties of Mars regolith

NASA Technical Reports Server (NTRS)

Schuerger, Andrew C.; Ming, Douglas W.; Newsom, Horton E.; Ferl, Robert J.; McKay, Christopher P.

2002-01-01

In order to support humans for long-duration missions to Mars, bioregenerative Advanced Life Support (ALS) systems have been proposed that would use higher plants as the primary candidates for photosynthesis. Hydroponic technologies have been suggested as the primary method of plant production in ALS systems, but the use of Mars regolith as a plant growth medium may have several advantages over hydroponic systems. The advantages for using Mars regolith include the likely bioavailability of plant-essential ions, mechanical support for plants, and easy access of the material once on the surface. We propose that plant biology experiments must be included in near-term Mars lander missions in order to begin defining the optimum approach for growing plants on Mars. Second, we discuss a range of soil chemistry and soil physics tests that must be conducted prior to, or in concert with, a plant biology experiment in order to properly interpret the results of plant growth studies in Mars regolith. The recommended chemical tests include measurements on soil pH, electrical conductivity and soluble salts, redox potential, bioavailability of essential plant nutrients, and bioavailability of phytotoxic elements. In addition, a future plant growth experiment should include procedures for determining the buffering and leaching requirements of Mars regolith prior to planting. Soil physical tests useful for plant biology studies in Mars regolith include bulk density, particle size distribution, porosity, water retention, and hydraulic conductivity.

A test of the orthographic recoding hypothesis

NASA Astrophysics Data System (ADS)

Gaygen, Daniel E.

2003-04-01

The Orthographic Recoding Hypothesis [D. E. Gaygen and P. A. Luce, Percept. Psychophys. 60, 465-483 (1998)] was tested. According to this hypothesis, listeners recognize spoken words heard for the first time by mapping them onto stored representations of the orthographic forms of the words. Listeners have a stable orthographic representation of words, but no phonological representation, when those words have been read frequently but never heard or spoken. Such may be the case for low frequency words such as jargon. Three experiments using visually and auditorily presented nonword stimuli tested this hypothesis. The first two experiments were explicit tests of memory (old-new tests) for words presented visually. In the first experiment, the recognition of auditorily presented nonwords was facilitated when they previously appeared on a visually presented list. The second experiment was similar, but included a concurrent articulation task during a visual word list presentation, thus preventing covert rehearsal of the nonwords. The results were similar to the first experiment. The third experiment was an indirect test of memory (auditory lexical decision task) for visually presented nonwords. Auditorily presented nonwords were identified as nonwords significantly more slowly if they had previously appeared on the visually presented list accompanied by a concurrent articulation task.

It's DE-licious: A Recipe for Differential Expression Analyses of RNA-seq Experiments Using Quasi-Likelihood Methods in edgeR.

PubMed

Lun, Aaron T L; Chen, Yunshun; Smyth, Gordon K

2016-01-01

RNA sequencing (RNA-seq) is widely used to profile transcriptional activity in biological systems. Here we present an analysis pipeline for differential expression analysis of RNA-seq experiments using the Rsubread and edgeR software packages. The basic pipeline includes read alignment and counting, filtering and normalization, modelling of biological variability and hypothesis testing. For hypothesis testing, we describe particularly the quasi-likelihood features of edgeR. Some more advanced downstream analysis steps are also covered, including complex comparisons, gene ontology enrichment analyses and gene set testing. The code required to run each step is described, along with an outline of the underlying theory. The chapter includes a case study in which the pipeline is used to study the expression profiles of mammary gland cells in virgin, pregnant and lactating mice.

Advances in Experiment Design for High Performance Aircraft

NASA Technical Reports Server (NTRS)

Morelli, Engene A.

1998-01-01

A general overview and summary of recent advances in experiment design for high performance aircraft is presented, along with results from flight tests. General theoretical background is included, with some discussion of various approaches to maneuver design. Flight test examples from the F-18 High Alpha Research Vehicle (HARV) are used to illustrate applications of the theory. Input forms are compared using Cramer-Rao bounds for the standard errors of estimated model parameters. Directions for future research in experiment design for high performance aircraft are identified.

APEX 3: a multi-purpose test platform for auditory psychophysical experiments.

PubMed

Francart, Tom; van Wieringen, Astrid; Wouters, Jan

2008-07-30

APEX 3 is a software test platform for auditory behavioral experiments. It provides a generic means of setting up experiments without any programming. The supported output devices include sound cards and cochlear implants from Cochlear Corporation and Advanced Bionics Corporation. Many psychophysical procedures are provided and there is an interface to add custom procedures. Plug-in interfaces are provided for data filters and external controllers. APEX 3 is supported under Linux and Windows and is available free of charge.

Decision-Making in Flight with Different Convective Weather Information Sources: Preliminary Results from the Langley CoWS Experiment (COnvective Weather Sources)

NASA Technical Reports Server (NTRS)

Chamberlain, Jim; Latorella, Kara

2003-01-01

This viewgraph presentation provides information on an airborne experiment designed to test the decision making of pilots receiving different sources of meteorological data. The presentation covers the equipment used in the COnvective Weather Sources (CoWS) Experiment), including the information system and display devices available to some of the subjects. It also describes the experiment, which featured teams of general aviation pilots, who were onboard but did not actually fly the aircraft used in the experiment. The presentation includes the results of a survey of the subjects' confidence.

Review of Transient Testing of Fast Reactor Fuels in the Transient REActor Test Facility (TREAT)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jensen, C.; Wachs, D.; Carmack, J.

The restart of the Transient REActor Test (TREAT) facility provides a unique opportunity to engage the fast reactor fuels community to reinitiate in-pile experimental safety studies. Historically, the TREAT facility played a critical role in characterizing the behavior of both metal and oxide fast reactor fuels under off-normal conditions, irradiating hundreds of fuel pins to support fast reactor fuel development programs. The resulting test data has provided validation for a multitude of fuel performance and severe accident analysis computer codes. This paper will provide a review of the historical database of TREAT experiments including experiment design, instrumentation, test objectives, andmore » salient findings. Additionally, the paper will provide an introduction to the current and future experiment plans of the U.S. transient testing program at TREAT.« less

JPL control/structure interaction test bed real-time control computer architecture

NASA Technical Reports Server (NTRS)

Briggs, Hugh C.

1989-01-01

The Control/Structure Interaction Program is a technology development program for spacecraft that exhibit interactions between the control system and structural dynamics. The program objectives include development and verification of new design concepts - such as active structure - and new tools - such as combined structure and control optimization algorithm - and their verification in ground and possibly flight test. A focus mission spacecraft was designed based upon a space interferometer and is the basis for design of the ground test article. The ground test bed objectives include verification of the spacecraft design concepts, the active structure elements and certain design tools such as the new combined structures and controls optimization tool. In anticipation of CSI technology flight experiments, the test bed control electronics must emulate the computation capacity and control architectures of space qualifiable systems as well as the command and control networks that will be used to connect investigators with the flight experiment hardware. The Test Bed facility electronics were functionally partitioned into three units: a laboratory data acquisition system for structural parameter identification and performance verification; an experiment supervisory computer to oversee the experiment, monitor the environmental parameters and perform data logging; and a multilevel real-time control computing system. The design of the Test Bed electronics is presented along with hardware and software component descriptions. The system should break new ground in experimental control electronics and is of interest to anyone working in the verification of control concepts for large structures.

Experimental data from coastal diffusion tests. [Smoke diffusion over coastal waters

DOE Office of Scientific and Technical Information (OSTI.GOV)

Raynor, G S; Brown, R M; SethuRaman, S

1976-10-01

Data are reported from a series of seven experiments on the diffusion of smoke plumes over northeast Atlantic Ocean coastal waters in response to wind fluctuations and other meteorological variables. A qualitative description of smoke behavior during each experiment is included and photographs of the smoke are included to illustrate the type of diffusion observed. (CH)

The Effect of Font Selection on Student Test Anxiety

ERIC Educational Resources Information Center

Murphy, Peter V.

2014-01-01

The emergence of standards-based curriculums has resulted in an increased frequency of student testing, including high-stakes testing. Of students who take tests, up to 65% may experience test anxiety, which can have negative effects on student outcomes. For this reason, the purpose of this single-group, repeated measures design, quantitative…

HIFiRE Direct-Connect Rig (HDCR) Phase I Ground Test Results from the NASA Langley Arc-Heated Scramjet Test Facility

NASA Technical Reports Server (NTRS)

Hass, Neal E.; Cabell, Karen F.; Storch, Andrea M.

2010-01-01

The initial phase of hydrocarbon-fueled ground tests supporting Flight 2 of the Hypersonic International Flight Research Experiment (HIFiRE) Program has been conducted in the NASA Langley Arc-Heated Scramjet Test Facility (AHSTF). The HIFiRE Program, an Air Force-lead international cooperative program includes eight different flight test experiments designed to target specific challenges of hypersonic flight. The second of the eight planned flight experiments is a hydrocarbon-fueled scramjet flight test intended to demonstrate dual-mode to scramjet-mode operation and verify the scramjet performance prediction and design tools. A performance goal is the achievement of a combusted fuel equivalence ratio greater than 0.7 while in scramjet mode. The ground test rig, designated the HIFiRE Direct Connect Rig (HDCR), is a full-scale, heat sink, direct-connect ground test article that duplicates both the flowpath lines and the instrumentation layout of the isolator and combustor portion of the flight test hardware. The primary objectives of the HDCR Phase I tests are to verify the operability of the HIFiRE isolator/combustor across the Mach 6.0-8.0 flight regime and to establish a fuel distribution schedule to ensure a successful mode transition prior to the HiFIRE payload Critical Design Review. Although the phase I test plans include testing over the Mach 6 to 8 flight simulation range, only Mach 6 testing will be reported in this paper. Experimental results presented here include flowpath surface pressure, temperature, and heat flux distributions that demonstrate the operation of the flowpath over a small range of test conditions around the nominal Mach 6 simulation, as well as a range of fuel equivalence ratios and fuel injection distributions. Both ethylene and a mixture of ethylene and methane (planned for flight) were tested. Maximum back pressure and flameholding limits, as well as a baseline fuel schedule, that covers the Mach 5.84-6.5 test space have been identified.

NASTRAN: Users' experiences

NASA Technical Reports Server (NTRS)

1973-01-01

The proceedings of a conference on NASA Structural Analysis (NASTRAN) to analyze the experiences of users of the program are presented. The subjects discussed include the following: (1) statics and buckling, (2) vibrations and dynamics, (3) substructing, (4) new capability, (5) user's experience, and (6) system experience. Specific applications of NASTRAN to spacecraft, aircraft, nuclear power plants, and materials tests are reported.

Cryogenic Tank Modeling for the Saturn AS-203 Experiment

NASA Technical Reports Server (NTRS)

Grayson, Gary D.; Lopez, Alfredo; Chandler, Frank O.; Hastings, Leon J.; Tucker, Stephen P.

2006-01-01

A computational fluid dynamics (CFD) model is developed for the Saturn S-IVB liquid hydrogen (LH2) tank to simulate the 1966 AS-203 flight experiment. This significant experiment is the only known, adequately-instrumented, low-gravity, cryogenic self pressurization test that is well suited for CFD model validation. A 4000-cell, axisymmetric model predicts motion of the LH2 surface including boil-off and thermal stratification in the liquid and gas phases. The model is based on a modified version of the commercially available FLOW3D software. During the experiment, heat enters the LH2 tank through the tank forward dome, side wall, aft dome, and common bulkhead. In both model and test the liquid and gases thermally stratify in the low-gravity natural convection environment. LH2 boils at the free surface which in turn increases the pressure within the tank during the 5360 second experiment. The Saturn S-IVB tank model is shown to accurately simulate the self pressurization and thermal stratification in the 1966 AS-203 test. The average predicted pressurization rate is within 4% of the pressure rise rate suggested by test data. Ullage temperature results are also in good agreement with the test where the model predicts an ullage temperature rise rate within 6% of the measured data. The model is based on first principles only and includes no adjustments to bring the predictions closer to the test data. Although quantitative model validation is achieved or one specific case, a significant step is taken towards demonstrating general use of CFD for low-gravity cryogenic fluid modeling.

Mars Pathfinder flight system integration and test.

NASA Astrophysics Data System (ADS)

Muirhead, B. K.

This paper describes the system integration and test experiences, problems and lessons learned during the assembly, test and launch operations (ATLO) phase of the Mars Pathfinder flight system scheduled to land on the surface of Mars on July 4, 1997. The Mars Pathfinder spacecraft consists of three spacecraft systems: cruise stage, entry vehicle and lander. The cruise stage carries the entry and lander vehicles to Mars and is jettisoned prior to entry. The entry vehicle, including aeroshell, parachute and deceleration rockets, protects the lander during the direct entry and reduces its velocity from 7.6 to 0 km/s in stages during the 5 min entry sequence. The lander's touchdown is softened by airbags which are retracted once stopped on the surface. The lander then uprights itself, opens up fully and begins surface operations including deploying its camera and rover. This paper overviews the system design and the results of the system integration and test activities, including the entry, descent and landing subsystem elements. System test experiences including science instruments, the microrover, Sojourner, and software are discussed. The final qualification of the entry, descent and landing subsystems during this period is also discussed.

The Not-so-Random Drunkard's Walk

ERIC Educational Resources Information Center

Ehrhardt, George

2013-01-01

This dataset contains the results of a quasi-experiment, testing Karl Pearson's "drunkard's walk" analogy for an abstract random walk. Inspired by the alternate hypothesis that drunkards stumble to the side of their dominant hand, it includes data on intoxicated test subjects walking a 10' line. Variables include: the…

Helping Students Cope with Test Anxiety. ERIC Digest.

ERIC Educational Resources Information Center

Harris, Henry L.; Coy, Doris R.

One of the most threatening events that causes anxiety in students today is testing. When students develop an extreme fear of performing poorly on an examination, they experience test anxiety. Test anxiety is a major factor contributing to a variety of negative outcomes including psychological distress, academic underachievement, academic failure,…

Space Construction Experiment Definition Study (SCEDS), part 2. Volume 2: Study results

NASA Technical Reports Server (NTRS)

1982-01-01

The Space Construction Experiment (SCE) was defined for integration into the Space Shuttle. This included development of flight assignment data, revision and update of preliminary mission timelines and test plans, analysis of flight safety issues, and definition of ground operations scenarios. New requirements for the flight experiment and changes for a large space antenna feed mask test article were incorporated. The program plan and cost estimates were updated. Revised SCE structural dynamics characteristics were provided for simulation and analysis of experimental tests to define and verify control limits and interactions effects between the SCE and the Orbiter digital automatic pilot.

High resolution frequency analysis techniques with application to the redshift experiment

NASA Technical Reports Server (NTRS)

Decher, R.; Teuber, D.

1975-01-01

High resolution frequency analysis methods, with application to the gravitational probe redshift experiment, are discussed. For this experiment a resolution of .00001 Hz is required to measure a slowly varying, low frequency signal of approximately 1 Hz. Major building blocks include fast Fourier transform, discrete Fourier transform, Lagrange interpolation, golden section search, and adaptive matched filter technique. Accuracy, resolution, and computer effort of these methods are investigated, including test runs on an IBM 360/65 computer.

Unit Operation Experiment Linking Classroom with Industrial Processing

ERIC Educational Resources Information Center

Benson, Tracy J.; Richmond, Peyton C.; LeBlanc, Weldon

2013-01-01

An industrial-type distillation column, including appropriate pumps, heat exchangers, and automation, was used as a unit operations experiment to provide a link between classroom teaching and real-world applications. Students were presented with an open-ended experiment where they defined the testing parameters to solve a generalized problem. The…

The Recovery and Identification of Flammable Liquids in Suspected Arsons: An Undergraduate Organic Experiment

ERIC Educational Resources Information Center

Blackledge, Robert D.

1974-01-01

Describes an experiment which can be used to test for the use of accelerants in the origin of a fire. Involves distillation and gas liquid chromatography to identify the accelerants, thus combining two experiments ordinarily included in the beginning organic laboratory. (SLH)

The problem of creating habits: establishing health-protective dental behaviors.

PubMed

McCaul, K D; Glasgow, R E; O'Neill, H K

1992-01-01

We describe three experiments testing treatments to promote the performance of health-protective dental behaviors. Subjects included 55 women from an introductory psychology course (Experiment 1), 45 men and women (Experiment 2), and 81 older-than-average students identified as at risk for gum disease (Experiment 3). The interventions, derived from social cognitive theory, included health education, skills training, and self-monitoring. In each study, we examined the contribution of additional treatment components, including social support (Experiment 1), intensive contact (Experiment 2), and flexible goal setting (Experiment 3). Across experiments, the behavioral results were remarkably similar: Subjects exhibited excellent adherence while in the study but, at follow-up, reported behavior that differed little from baseline. We discuss parallels between attempts to promote health-protective dental behaviors and other health-promotion programs, and we describe different perspectives from which to address the problem of creating healthy habits.

Design preferences and cognitive styles: experimentation by automated website synthesis.

PubMed

Leung, Siu-Wai; Lee, John; Johnson, Chris; Robertson, David

2012-06-29

This article aims to demonstrate computational synthesis of Web-based experiments in undertaking experimentation on relationships among the participants' design preference, rationale, and cognitive test performance. The exemplified experiments were computationally synthesised, including the websites as materials, experiment protocols as methods, and cognitive tests as protocol modules. This work also exemplifies the use of a website synthesiser as an essential instrument enabling the participants to explore different possible designs, which were generated on the fly, before selection of preferred designs. The participants were given interactive tree and table generators so that they could explore some different ways of presenting causality information in tables and trees as the visualisation formats. The participants gave their preference ratings for the available designs, as well as their rationale (criteria) for their design decisions. The participants were also asked to take four cognitive tests, which focus on the aspects of visualisation and analogy-making. The relationships among preference ratings, rationale, and the results of cognitive tests were analysed by conservative non-parametric statistics including Wilcoxon test, Krustal-Wallis test, and Kendall correlation. In the test, 41 of the total 64 participants preferred graphical (tree-form) to tabular presentation. Despite the popular preference for graphical presentation, the given tabular presentation was generally rated to be easier than graphical presentation to interpret, especially by those who were scored lower in the visualization and analogy-making tests. This piece of evidence helps generate a hypothesis that design preferences are related to specific cognitive abilities. Without the use of computational synthesis, the experiment setup and scientific results would be impractical to obtain.

An Investigation of the Teacher Competencies Needed to Utilize Diagnostic Test Data in Prescribing Occupational Learning Experiences in Teaching EMRS. Final Report. Part II. Appendices.

ERIC Educational Resources Information Center

Nelson, Orville; And Others

These appendixes are to the final report of an action research Project conducted to determine the teacher competencies needed in order to develop valid and effective occupational learning experiences for educable mentally retarded (EMR) students based on available diagnostic test data and information. Included are (1) participant vitas and…

System Report for the Optical Properties Monitor (OPM) Experiment

NASA Technical Reports Server (NTRS)

Hummer, L.

2001-01-01

This systems report describes how the Optical Properties Monitor (OPM) experiment was developed. Pertinent design parameters are discussed, along with mission information and system requirements to successfully complete the mission. Environmental testing was performed on the OPM to certify it for spaceflight. This testing included vibration, thermal vacuum, electromagnetic interference and conductance, and toxicity tests. Instrument and monitor subsystem performances, including the reflectometer, vacuum ultraviolet, total integrated scatter, atomic oxygen monitor, irradiance monitor, and molecular contamination monitor during the mission are discussed. The OPM experiment was launched aboard the Space Shuttle on mission STS-81 in January 1997 and transferred to the Mir space station. An extravehicular activity (EVA) was performed in April 1997 to attach the OPM experiment to the outside of the Mir/Shuttle Docking Module for space environment exposure. The OPM conducted in situ measurements of a number of material samples. These data may be found in the OPM Science Report. OPM was retrieved during an EVA in January 1998 and was returned to Earth on board the Space Shuttle on mission STS-89.

Toward a Mechanistic Source Term in Advanced Reactors: A Review of Past U.S. SFR Incidents, Experiments, and Analyses

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bucknor, Matthew; Brunett, Acacia J.; Grabaskas, David

In 2015, as part of a Regulatory Technology Development Plan (RTDP) effort for sodium-cooled fast reactors (SFRs), Argonne National Laboratory investigated the current state of knowledge of source term development for a metal-fueled, pool-type SFR. This paper provides a summary of past domestic metal-fueled SFR incidents and experiments and highlights information relevant to source term estimations that were gathered as part of the RTDP effort. The incidents described in this paper include fuel pin failures at the Sodium Reactor Experiment (SRE) facility in July of 1959, the Fermi I meltdown that occurred in October of 1966, and the repeated meltingmore » of a fuel element within an experimental capsule at the Experimental Breeder Reactor II (EBR-II) from November 1967 to May 1968. The experiments described in this paper include the Run-Beyond-Cladding-Breach tests that were performed at EBR-II in 1985 and a series of severe transient overpower tests conducted at the Transient Reactor Test Facility (TREAT) in the mid-1980s.« less

Vocabulary Knowledge Predicts Lexical Processing: Evidence from a Group of Participants with Diverse Educational Backgrounds

PubMed Central

Mainz, Nina; Shao, Zeshu; Brysbaert, Marc; Meyer, Antje S.

2017-01-01

Vocabulary knowledge is central to a speaker's command of their language. In previous research, greater vocabulary knowledge has been associated with advantages in language processing. In this study, we examined the relationship between individual differences in vocabulary and language processing performance more closely by (i) using a battery of vocabulary tests instead of just one test, and (ii) testing not only university students (Experiment 1) but young adults from a broader range of educational backgrounds (Experiment 2). Five vocabulary tests were developed, including multiple-choice and open antonym and synonym tests and a definition test, and administered together with two established measures of vocabulary. Language processing performance was measured using a lexical decision task. In Experiment 1, vocabulary and word frequency were found to predict word recognition speed while we did not observe an interaction between the effects. In Experiment 2, word recognition performance was predicted by word frequency and the interaction between word frequency and vocabulary, with high-vocabulary individuals showing smaller frequency effects. While overall the individual vocabulary tests were correlated and showed similar relationships with language processing as compared to a composite measure of all tests, they appeared to share less variance in Experiment 2 than in Experiment 1. Implications of our findings concerning the assessment of vocabulary size in individual differences studies and the investigation of individuals from more varied backgrounds are discussed. PMID:28751871

Aerodynamic Database Development for the Hyper-X Airframe Integrated Scramjet Propulsion Experiments

NASA Technical Reports Server (NTRS)

Engelund, Walter C.; Holland, Scott D.; Cockrell, Charles E., Jr.; Bittner, Robert D.

2000-01-01

This paper provides an overview of the activities associated with the aerodynamic database which is being developed in support of NASA's Hyper-X scramjet flight experiments. Three flight tests are planned as part of the Hyper-X program. Each will utilize a small, nonrecoverable research vehicle with an airframe integrated scramjet propulsion engine. The research vehicles will be individually rocket boosted to the scramjet engine test points at Mach 7 and Mach 10. The research vehicles will then separate from the first stage booster vehicle and the scramjet engine test will be conducted prior to the terminal decent phase of the flight. An overview is provided of the activities associated with the development of the Hyper-X aerodynamic database, including wind tunnel test activities and parallel CFD analysis efforts for all phases of the Hyper-X flight tests. A brief summary of the Hyper-X research vehicle aerodynamic characteristics is provided, including the direct and indirect effects of the airframe integrated scramjet propulsion system operation on the basic airframe stability and control characteristics. Brief comments on the planned post flight data analysis efforts are also included.

Qualification testing and electrical measurement experience: A manufacturer's view

NASA Astrophysics Data System (ADS)

Arnett, J. C.; Cooley, J. E.; Wingert, T. L.

1983-11-01

ARCO Solar's experiences as a participant in an industry-utility-government environmental qualification team examining photovoltaic devices are discussed. Included is an assessment of the applicability, completeness and appropriateness of the testing procedures and of the acceptance criteria for megawatt-sized procurements for utilities. Like the stand-alone users, the utility industry is interested in obtaining low costs, but additional concerns exist related to reliability and durability, safety, grounding and overall system criteria including performance prediction (related to output power acceptance testing), power quality and dispatchability. For purposes of this first major purchase of photovoltaic modules and panels by the utility industry, there was a carry-over of the JPL specifications. The need exists for futher development, assessement, and selection of qualification and testing standards and evaluation criteria specifically addressing these additional concerns for utility-connected PV power-plant applications.

Qualification testing and electrical measurement experience: A manufacturer's view

NASA Technical Reports Server (NTRS)

Arnett, J. C.; Cooley, J. E.; Wingert, T. L.

1983-01-01

ARCO Solar's experiences as a participant in an industry-utility-government environmental qualification team examining photovoltaic devices are discussed. Included is an assessment of the applicability, completeness and appropriateness of the testing procedures and of the acceptance criteria for megawatt-sized procurements for utilities. Like the stand-alone users, the utility industry is interested in obtaining low costs, but additional concerns exist related to reliability and durability, safety, grounding and overall system criteria including performance prediction (related to output power acceptance testing), power quality and dispatchability. For purposes of this first major purchase of photovoltaic modules and panels by the utility industry, there was a carry-over of the JPL specifications. The need exists for futher development, assessement, and selection of qualification and testing standards and evaluation criteria specifically addressing these additional concerns for utility-connected PV power-plant applications.

Operational overview of NASA GTE/CITE 1 airborne instrument intercomparisons - Carbon monoxide, nitric oxide, and hydroxyl instrumentation. [Global Tropospheric Experiment/Chemical Instrumentation Test and Evaluation

NASA Technical Reports Server (NTRS)

Beck, Sherwin M.; Bendura, Richard J.; Mcdougal, David S.; Hoell, James M., Jr.; Gregory, Gerald L.; Sachse, Glen W.; Hill, Gerald F.; Curfman, Howard J., Jr.; Torres, Arnold L.; Condon, Estelle P.

1987-01-01

An overview of the airborne intercomparisons of CO, NO, and OH instrumentation is presented in this first paper of the series on the NASA Global Tropospheric Experiment/Chemical Instrumentation Test and Evaluation (GTE/CITE 1). This paper provides the reader with background information about several important characteristics of the project. These include the overall objectives and approach, the measurements taken, the intercomparison protocol, aircraft platform, profiles of each aircraft flight, and the participants. A synopsis of the overall results of the CO, NO, and OH instrument intercomparisons is also included. Companion papers discuss the detailed results of the CO and NO intercomparison tests as well as pertinent scientific findings.

Chemistry Notes.

ERIC Educational Resources Information Center

School Science Review, 1983

1983-01-01

Presents chemistry experiments, laboratory procedures, demonstrations, and classroom materials/activities. These include: experiments on colloids, processing of uranium ore, action of heat on carbonates; color test for phenols and aromatic amines; solvent properties of non-electrolytes; stereoscopic applications/methods; a valency balance;…

Beam test results of STS prototype modules for the future accelerator experiments FAIR/CBM and NICA/MPD projects

NASA Astrophysics Data System (ADS)

Kharlamov, Petr; Dementev, Dmitrii; Shitenkov, Mikhail

2017-10-01

High-energy heavy-ion collision experiments provide the unique possibility to create and investigate extreme states of strongly-interacted matter and address the fundamental aspects of QCD. The experimental investigation the QCD phase diagram would be a major breakthrough in our understanding of the properties of nuclear matter. The reconstruction of the charged particles created in the nuclear collisions, including the determination of their momenta, is the central detection task in high-energy heavy-ion experiments. It is taken up by the Silicon Tracking System in CBM@FAIR and by Inner Tracker in MPD@NICA currently under development. These experiments requires very fast and radiation hard detectors, a novel data read-out and analysis concept including free streaming front-end electronics. Thermal and beam tests of prototype detector modules for these tracking systems showed the stability of sensors and readout electronics operation.

STS-70 Post Flight Presentation

NASA Technical Reports Server (NTRS)

Peterson, Glen (Editor)

1995-01-01

In this post-flight overview, the flight crew of the STS-70 mission, Tom Henricks (Cmdr.), Kevin Kregel (Pilot), Major Nancy Currie (MS), Dr. Mary Ellen Weber (MS), and Dr. Don Thomas (MS), discuss their mission and accompanying experiments. Pre-flight, launch, and orbital footage is followed by the in-orbit deployment of the Tracking and Data Relay Satellite (TDRS) and a discussion of the following spaceborne experiments: a microgravity bioreactor experiment to grow 3D body-like tissue; pregnant rat muscular changes in microgravity; embryonic development in microgravity; Shuttle Amateur Radio Experiment (SAREX); terrain surface imagery using the HERCULES camera; and a range of other physiological tests, including an eye and vision test. Views of Earth include: tropical storm Chantal; the Nile River and Red Sea; lightning over Brazil. A three planet view (Earth, Mars, and Venus) was taken right before sunrise. The end footage shows shuttle pre-landing checkout, entry, and landing, along with a slide presentation of the flight.

Initial Flight Tests of the NASA F-15B Propulsion Flight Test Fixture

NASA Technical Reports Server (NTRS)

Palumbo, Nathan; Moes, Timothy R.; Vachon, M. Jake

2002-01-01

Flights of the F-15B/Propulsion Flight Test Fixture (PFTF) with a Cone Drag Experiment (CDE) attached have been accomplished at NASA Dryden Flight Research Center. Mounted underneath the fuselage of an F-15B airplane, the PFTF provides volume for experiment systems and attachment points for propulsion experiments. A unique feature of the PFTF is the incorporation of a six-degree-of-freedom force balance. The force balance mounts between the PFTF and experiment and measures three forces and moments. The CDE has been attached to the force balance for envelope expansion flights. This experiment spatially and inertially simulates a large propulsion test article. This report briefly describes the F-15B airplane, the PFTF, and the force balance. A detailed description of the CDE is provided. Force-balance ground testing and stiffness modifications are described. Flight profiles and selected flight data from the envelope expansion flights are provided and discussed, including force-balance data, the internal PFTF thermal and vibration environment, a handling qualities assessment, and performance capabilities of the F-15B airplane with the PFTF installed.

Aerobic biodegradability of methyldiethanolamine (MDEA) used in natural gas sweetening plants in batch tests and continuous flow experiments.

PubMed

Fürhacker, M; Pressl, A; Allabashi, R

2003-09-01

Mixtures of different amines including tertiary amines (methyldiethanolamine, MDEA) are commonly used for the removal of CO2 from gas mixtures or in gas sweetening processes for the extraction of CO2 and H2S. The absorber solutions used can be released into the industrial waste water due to continuous substitution of degraded MDEA, periodically cleaning processes or an accidental spill. In this study, the aerobic biodegradability of MDEA was investigated in a standardised batch test and a continuous flow experiment (40 l/d). The results of the batch test indicated that the MDEA-solution was non-biodegradable during the test period of 28 days, whereas the continuous flow experiments showed biodegradation of more than 96% based on TOC-measurements. This was probably due to the adaptation of the microorganisms to this particular waste water contamination during continuous flow experiment.

Environmental qualification testing of the prototype pool boiling experiment

NASA Technical Reports Server (NTRS)

Sexton, J. Andrew

1992-01-01

The prototype Pool Boiling Experiment (PBE) flew on the STS-47 mission in September 1992. This report describes the purpose of the experiment and the environmental qualification testing program that was used to prove the integrity of the prototype hardware. Component and box level vibration and thermal cycling tests were performed to give an early level of confidence in the hardware designs. At the system level, vibration, thermal extreme soaks, and thermal vacuum cycling tests were performed to qualify the complete design for the expected shuttle environment. The system level vibration testing included three axis sine sweeps and random inputs. The system level hot and cold soak tests demonstrated the hardware's capability to operate over a wide range of temperatures and gave the project team a wider latitude in determining which shuttle thermal altitudes were compatible with the experiment. The system level thermal vacuum cycling tests demonstrated the hardware's capability to operate in a convection free environment. A unique environmental chamber was designed and fabricated by the PBE team and allowed most of the environmental testing to be performed within the project's laboratory. The completion of the test program gave the project team high confidence in the hardware's ability to function as designed during flight.

The Cryogenic Test Bed experiments: Cryogenic heat pipe flight experiment CRYOHP (STS-53). Cryogenic two phase flight experiment CRYOTP (STS-62). Cryogenic flexible diode flight experiment CRYOFD

NASA Astrophysics Data System (ADS)

Thienel, Lee; Stouffer, Chuck

1995-09-01

This paper presents an overview of the Cryogenic Test Bed (CTB) experiments including experiment results, integration techniques used, and lessons learned during integration, test and flight phases of the Cryogenic Heat Pipe Flight Experiment (STS-53) and the Cryogenic Two Phase Flight Experiment (OAST-2, STS-62). We will also discuss the Cryogenic Flexible Diode Heat Pipe (CRYOFD) experiment which will fly in the 1996/97 time frame and the fourth flight of the CTB which will fly in the 1997/98 time frame. The two missions tested two oxygen axially grooved heat pipes, a nitrogen fibrous wick heat pipe and a 2-methylpentane phase change material thermal storage unit. Techniques were found for solving problems with vibration from the cryo-collers transmitted through the compressors and the cold heads, and mounting the heat pipe without introducing parasitic heat leaks. A thermally conductive interface material was selected that would meet the requirements and perform over the temperature range of 55 to 300 K. Problems are discussed with the bi-metallic thermostats used for heater circuit protection and the S-Glass suspension straps originally used to secure the BETSU PCM in the CRYOTP mission. Flight results will be compared to 1-g test results and differences will be discussed.

The Cryogenic Test Bed experiments: Cryogenic heat pipe flight experiment CRYOHP (STS-53). Cryogenic two phase flight experiment CRYOTP (STS-62). Cryogenic flexible diode flight experiment CRYOFD

NASA Technical Reports Server (NTRS)

Thienel, Lee; Stouffer, Chuck

1995-01-01

This paper presents an overview of the Cryogenic Test Bed (CTB) experiments including experiment results, integration techniques used, and lessons learned during integration, test and flight phases of the Cryogenic Heat Pipe Flight Experiment (STS-53) and the Cryogenic Two Phase Flight Experiment (OAST-2, STS-62). We will also discuss the Cryogenic Flexible Diode Heat Pipe (CRYOFD) experiment which will fly in the 1996/97 time frame and the fourth flight of the CTB which will fly in the 1997/98 time frame. The two missions tested two oxygen axially grooved heat pipes, a nitrogen fibrous wick heat pipe and a 2-methylpentane phase change material thermal storage unit. Techniques were found for solving problems with vibration from the cryo-collers transmitted through the compressors and the cold heads, and mounting the heat pipe without introducing parasitic heat leaks. A thermally conductive interface material was selected that would meet the requirements and perform over the temperature range of 55 to 300 K. Problems are discussed with the bi-metallic thermostats used for heater circuit protection and the S-Glass suspension straps originally used to secure the BETSU PCM in the CRYOTP mission. Flight results will be compared to 1-g test results and differences will be discussed.

Apollo experience report environmental acceptance testing

NASA Technical Reports Server (NTRS)

Laubach, C. H. M.

1976-01-01

Environmental acceptance testing was used extensively to screen selected spacecraft hardware for workmanship defects and manufacturing flaws. The minimum acceptance levels and durations and methods for their establishment are described. Component selection and test monitoring, as well as test implementation requirements, are included. Apollo spacecraft environmental acceptance test results are summarized, and recommendations for future programs are presented.

Cryogenic On-Orbit Liquid Depot-Storage, Acquisition and Transfer (COLD-SAT) Experiment Conceptual Design and Feasibility Study

NASA Technical Reports Server (NTRS)

Kramer, Edward (Editor)

1998-01-01

The cryogenic fluid management technologies required for the exploration of the solar system can only be fully developed via space-based experiments. A dedicated spacecraft is the most efficient way to perform these experiments. This report documents the extended conceptual design of the COLD-SAT spacecraft, capable of meeting these experimental requirements. All elements, including the spacecraft, ground segment, launch site modifications and launch vehicle operations, and flight operations are included. Greatly expanded coverage is provided for those areas unique to this cryogenic spacecraft, such as the experiment system, attitude control system, and spacecraft operations. Supporting analyses are included as are testing requirements, facilities surveys, and proposed project timelines.

Experimental Results From a 2kW Brayton Power Conversion Unit

NASA Technical Reports Server (NTRS)

Hervol, David; Mason, Lee; Birchenough, Arthur

2003-01-01

This paper presents experimental test results from operation of a 2 kWe Brayton power conversion unit. The Brayton converter was developed for a solar dynamic power system flight experiment planned for the Mir Space Station in 1997. The flight experiment was cancelled, but the converter was tested at Glenn Research Center as part of the Solar Dynamic Ground Test Demonstration system which included a solar concentrator, heat receiver, and space radiator. In preparation for the current testing, the heat receiver was removed and replaced with an electrical resistance heater, simulating the thermal input of a steady-state nuclear source. The converter was operated over a full range of thermal input power levels and rotor speeds to generate an overall performance map. The converter unit will serve as the centerpiece of a Nuclear Electric Propulsion Testbed at Glenn. Future potential uses for the Testbed include high voltage electrical controller development, integrated electric thruster testing and advanced radiator demonstration testing to help guide high power Brayton technology development for Nuclear Electric Propulsion (NEP).

Experience in Grid Site Testing for ATLAS, CMS and LHCb with HammerCloud

NASA Astrophysics Data System (ADS)

Elmsheuser, Johannes; Medrano Llamas, Ramón; Legger, Federica; Sciabà, Andrea; Sciacca, Gianfranco; Úbeda García, Mario; van der Ster, Daniel

2012-12-01

Frequent validation and stress testing of the network, storage and CPU resources of a grid site is essential to achieve high performance and reliability. HammerCloud was previously introduced with the goals of enabling VO- and site-administrators to run such tests in an automated or on-demand manner. The ATLAS, CMS and LHCb experiments have all developed VO plugins for the service and have successfully integrated it into their grid operations infrastructures. This work will present the experience in running HammerCloud at full scale for more than 3 years and present solutions to the scalability issues faced by the service. First, we will show the particular challenges faced when integrating with CMS and LHCb offline computing, including customized dashboards to show site validation reports for the VOs and a new API to tightly integrate with the LHCbDIRAC Resource Status System. Next, a study of the automatic site exclusion component used by ATLAS will be presented along with results for tuning the exclusion policies. A study of the historical test results for ATLAS, CMS and LHCb will be presented, including comparisons between the experiments’ grid availabilities and a search for site-based or temporal failure correlations. Finally, we will look to future plans that will allow users to gain new insights into the test results; these include developments to allow increased testing concurrency, increased scale in the number of metrics recorded per test job (up to hundreds), and increased scale in the historical job information (up to many millions of jobs per VO).

Apollo experience report: Electronic systems test program accomplishments and results

NASA Technical Reports Server (NTRS)

Ohnesorge, T. E.

1972-01-01

A chronological record is presented of the Electronic Systems Test Program from its conception in May 1963 to December 1969. The original concept of the program, which was primarily a spacecraft/Manned Space Flight Network communications system compatibility and performance evaluation, is described. The evolution of these concepts to include various levels of test detail, as well as systems level design verification testing, is discussed. Actual implementation of these concepts is presented, and the facility to support the program is described. Test results are given, and significant contributions to the lunar landing mission are underlined. Plans for modifying the facility and the concepts, based on Apollo experience, are proposed.

Multiple environmental stressors elicit complex interactive effects in the western fence lizard (Sceloporus occidentalis).

PubMed

McFarland, Craig A; Talent, Larry G; Quinn, Michael J; Bazar, Matthew A; Wilbanks, Mitchell S; Nisanian, Mandana; Gogal, Robert M; Johnson, Mark S; Perkins, Edward J; Gust, Kurt A

2012-11-01

Evaluation of multiple-stressor effects stemming from habitat degradation, climate change, and exposure to chemical contaminants is crucial for addressing challenges to ecological and environmental health. To assess the effects of multiple stressors in an understudied taxon, the western fence lizard (Sceloporus occidentalis) was used to characterize the individual and combined effects of food limitation, exposure to the munitions constituent 2,4,6-trinitrotoluene (TNT), and Plasmodium mexicanum (lizard malaria) infection. Three experimental assays were conducted including: Experiment I--TNT × Food Limitation, Experiment II--Food Limitation × Malaria Infection, and Experiment III--TNT × Malaria Infection. All experiments had a 30 day duration, the malaria treatment included infected and non infected control lizards, food limitation treatments included an ad libitum control and at least one reduced food ration and TNT exposures consisting of daily oral doses of corn oil control or a corn oil-TNT suspension at 5, 10, 20, 40 mg/kg/day. The individual stressors caused a variety of effects including: reduced feeding, reduced testes mass, anemia, increased white blood cell (WBC) concentrations and increased mass of liver, kidney and spleen in TNT exposures; reduced cholesterol, WBC concentrations and whole body, testes and inguinal fat weights given food limitation; and increased WBC concentrations and spleen weights as well as decreased cholesterol and testes mass in malaria infected lizards. Additive and interactive effects were found among certain stressor combinations including elimination of TNT-induced hormesis for growth under food limitation. Ultimately, our study indicates the potential for effects modulation when environmental stressors are combined.

Modelling of LOCA Tests with the BISON Fuel Performance Code

DOE Office of Scientific and Technical Information (OSTI.GOV)

Williamson, Richard L; Pastore, Giovanni; Novascone, Stephen Rhead

2016-05-01

BISON is a modern finite-element based, multidimensional nuclear fuel performance code that is under development at Idaho National Laboratory (USA). Recent advances of BISON include the extension of the code to the analysis of LWR fuel rod behaviour during loss-of-coolant accidents (LOCAs). In this work, BISON models for the phenomena relevant to LWR cladding behaviour during LOCAs are described, followed by presentation of code results for the simulation of LOCA tests. Analysed experiments include separate effects tests of cladding ballooning and burst, as well as the Halden IFA-650.2 fuel rod test. Two-dimensional modelling of the experiments is performed, and calculationsmore » are compared to available experimental data. Comparisons include cladding burst pressure and temperature in separate effects tests, as well as the evolution of fuel rod inner pressure during ballooning and time to cladding burst. Furthermore, BISON three-dimensional simulations of separate effects tests are performed, which demonstrate the capability to reproduce the effect of azimuthal temperature variations in the cladding. The work has been carried out in the frame of the collaboration between Idaho National Laboratory and Halden Reactor Project, and the IAEA Coordinated Research Project FUMAC.« less

Virtual geotechnical laboratory experiments using a simulator

NASA Astrophysics Data System (ADS)

Penumadu, Dayakar; Zhao, Rongda; Frost, David

2000-04-01

The details of a test simulator that provides a realistic environment for performing virtual laboratory experimentals in soil mechanics is presented. A computer program Geo-Sim that can be used to perform virtual experiments, and allow for real-time observations of material response is presented. The results of experiments, for a given set of input parameters, are obtained with the test simulator using well-trained artificial neural-network-based soil models for different soil types and stress paths. Multimedia capabilities are integrated in Geo-Sim, using software that links and controls a laser disc player with a real-time parallel processing ability. During the simulation of a virtual experiment, relevant portions of the video image of a previously recorded test on an actual soil specimen are dispalyed along with the graphical presentation of response from the feedforward ANN model predictions. The pilot simulator developed to date includes all aspects related to performing a triaxial test on cohesionless soil under undrained and drained conditions. The benefits of the test simulator are also presented.

Contextual memory and skill transfer in category search.

PubMed

Kole, James A; Healy, Alice F; Fierman, Deanna M; Bourne, Lyle E

2010-01-01

In three experiments, we examined transfer and contextual memory in a category search task. Each experiment included two phases (training and test), during which participants searched through category and exemplar menus for targets. In Experiment 1, the targets were from one of two domains during training (grocery store or department store); the domain was either the same or changed at test. Also, the categories were organized in one of two ways (alphabetically or semantically); the organization either remained the same or changed at test. In Experiments 2 and 3, domain and organization were held constant; however, categories or exemplars were the same, partially replaced, or entirely replaced across phases in order to simulate the dynamic nature of category search in everyday situations. Transfer occurred at test when the category organization or domain was maintained and when the categories or exemplars matched (partially or entirely) those at training. These results demonstrate that transfer is facilitated by overlap in training and testing contexts.

77 FR 14319 - Unmanned Aircraft System Test Sites

Federal Register 2010, 2011, 2012, 2013, 2014

2012-03-09

... DoD and NASA. A project at a test range (a defined geographic area where research and development are..., the FAA believes that the new test sites need to include focal points to ensure that research is... and experience in conducting UAS operations and research. Methods that test site operators can use for...

The right wing of the LEFT airplane

NASA Technical Reports Server (NTRS)

Powell, Arthur G.

1987-01-01

The NASA Leading-Edge Flight Test (LEFT) program addressed the environmental issues which were potential problems in the application of Laminar Flow Control (LFC) to transport aircraft. These included contamination of the LFC surface due to dirt, rain, insect remains, snow, and ice, in the critical leading-edge region. Douglas Aircraft Company designed and built a test article which was mounted on the right wing of the C-140 JetStar aircraft. The test article featured a retractable leading-edge high-lift shield for contamination protection and suction through perforations on the upper surface for LFC. Following a period of developmental flight testing, the aircraft entered simulated airline service, which included exposure to airborne insects, heavy rain, snow, and icing conditions both in the air and on the ground. During the roughly 3 years of flight testing, the test article has consistently demonstrated laminar flow in cruising flight. The experience with the LEFT experiment was summarized with emphasis on significant test findings. The following items were discussed: test article design and features; suction distribution; instrumentation and transition point reckoning; problems and fixes; system performance and maintenance requirements.

An Experiment on a Physical Pendulum and Steiner's Theorem

ERIC Educational Resources Information Center

Russeva, G. B.; Tsutsumanova, G. G.; Russev, S. C.

2010-01-01

Introductory physics laboratory curricula usually include experiments on the moment of inertia, the centre of gravity, the harmonic motion of a physical pendulum, and Steiner's theorem. We present a simple experiment using very low cost equipment for investigating these subjects in the general case of an asymmetrical test body. (Contains 3 figures…

Optimal Foraging by Birds: Experiments for Secondary & Postsecondary Students

ERIC Educational Resources Information Center

Pecor, Keith W.; Lake, Ellen C.; Wund, Matthew A.

2015-01-01

Optimal foraging theory attempts to explain the foraging patterns observed in animals, including their choice of particular food items and foraging locations. We describe three experiments designed to test hypotheses about food choice and foraging habitat preference using bird feeders. These experiments can be used alone or in combination and can…

Design of a water electrolysis flight experiment

NASA Technical Reports Server (NTRS)

Lee, M. Gene; Grigger, David J.; Thompson, C. Dean; Cusick, Robert J.

1993-01-01

Supply of oxygen (O2) and hydrogen (H2) by electolyzing water in space will play an important role in meeting the National Aeronautics and Space Administration's (NASA's) needs and goals for future space missios. Both O2 and H2 are envisioned to be used in a variety of processes including crew life support, spacecraft propulsion, extravehicular activity, electrical power generation/storage as well as in scientific experiment and manufacturing processes. The Electrolysis Performance Improvement Concept Study (EPICS) flight experiment described herein is sponsored by NASA Headquarters as a part of the In-Space Technology Experiment Program (IN-STEP). The objective of the EPICS is to further contribute to the improvement of the SEF technology, specifially by demonstrating and validating the SFE electromechanical process in microgravity as well as investigating perrformance improvements projected possible in a microgravity environment. This paper defines the experiment objective and presents the results of the preliminary design of the EPICS. The experiment will include testing three subscale self-contained SFE units: one containing baseline components, and two units having variations in key component materials. Tests will be conducted at varying current and thermal condition.

RERTR-13 Irradiation Summary Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

D. M. Perez; M. A. Lillo; G. S. Chang

2012-09-01

The Reduced Enrichment for Research and Test Reactor (RERTR) experiment RERTR-13 was designed to assess performance of different types of neutron absorbers that can be potentially used as burnable poisons in the low enriched uranium-molybdenum based dispersion and monolithic fuels.1 The following report summarizes the life of the RERTR-13 experiment through end of irradiation, including as-run neutronic analysis results, thermal analysis results and hydraulic testing results.

Sleep can reduce the testing effect: it enhances recall of restudied items but can leave recall of retrieved items unaffected.

PubMed

Bäuml, Karl-Heinz T; Holterman, Christoph; Abel, Magdalena

2014-11-01

The testing effect refers to the finding that retrieval practice in comparison to restudy of previously encoded contents can improve memory performance and reduce time-dependent forgetting. Naturally, long retention intervals include both wake and sleep delay, which can influence memory contents differently. In fact, sleep immediately after encoding can induce a mnemonic benefit, stabilizing and strengthening the encoded contents. We investigated in a series of 5 experiments whether sleep influences the testing effect. After initial study of categorized item material (Experiments 1, 2, and 4A), paired associates (Experiment 3), or educational text material (Experiment 4B), subjects were asked to restudy encoded contents or engage in active retrieval practice. A final recall test was conducted after a 12-hr delay that included diurnal wakefulness or nocturnal sleep. The results consistently showed typical testing effects after the wake delay. However, these testing effects were reduced or even eliminated after sleep, because sleep benefited recall of restudied items but left recall of retrieved items unaffected. The findings are consistent with the bifurcation model of the testing effect (Kornell, Bjork, & Garcia, 2011), according to which the distribution of memory strengths across items is shifted differentially by retrieving and restudying, with retrieval strengthening items to a much higher degree than restudy does. On the basis of this model, most of the retrieved items already fall above recall threshold in the absence of sleep, so additional sleep-induced strengthening may not improve recall of retrieved items any further. PsycINFO Database Record (c) 2014 APA, all rights reserved.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Warpinski, N.R.; Branagan, P.T.; Sattler, A.R.

This paper is a case study of the stimulation and testing of tight, lenticular sands in the paludal interval of the Mesaverde group in the Piceance basin at DOE's Multiwell Experiment (MWX) site in Colorado. Topics discussed include geologic data, stress test results, well testing, laboratory core studies, stimulation and stimulation analyses, and postfracture operations.

Early results of the ionospheric experiment of the Apollo-Soyuz Test Project

NASA Technical Reports Server (NTRS)

Grossi, M. D.; Gay, R. H.

1976-01-01

A description is presented of a spacecraft-to-spacecraft Doppler-tracking experiment which was performed by the Smithsonian Astrophysical Observatory on the occasion of the Apollo-Soyuz Test Project (ASTP). The experiment involved the measurement of the relative velocity between the ASTP docking module and the Apollo command service module by a Doppler-tracking method. The objectives of the ionospheric experiment include the measurement of the time changes of the columnar electron content between the two spacecraft. The obtained data can provide a basis for the determination of the horizontal gradients of electron density at the height of 220 km.

OAO-3 end of mission tests report

NASA Technical Reports Server (NTRS)

Kalil, F.; Kull, F. J.; Mcintosh, R.; Ollendorf, S.; Margolies, D. L.; Gemmell, J.; Tasevoli, C. M.; Polidan, R. S.; Kochevar, H.; Chapman, C.

1981-01-01

Twelve engineering type tests were performed on several subsystems and experiment(s) of the OAO 3 spacecraft near its end of mission. The systems tested include: Princeton experiment package (PEP), fine error system guidance, inertial reference unit, star trackers, heat pipes, thermal control coatings, command and data handling, solar array; batteries, and onboard processor/power boost regulator. Generally, the systems performed well for the 8 1/2 years life of OAO 3, although some degradation was noted in the sensitivity of PEP and in the absorptivity of the skin coatings. Battery life was prolonged during the life of the mission in large part by carefully monitoring the charge-discharge cycle with careful attention not to overcharge.

Laboratory development and testing of spacecraft diagnostics

NASA Astrophysics Data System (ADS)

Amatucci, William; Tejero, Erik; Blackwell, Dave; Walker, Dave; Gatling, George; Enloe, Lon; Gillman, Eric

2017-10-01

The Naval Research Laboratory's Space Chamber experiment is a large-scale laboratory device dedicated to the creation of large-volume plasmas with parameters scaled to realistic space plasmas. Such devices make valuable contributions to the investigation of space plasma phenomena under controlled, reproducible conditions, allowing for the validation of theoretical models being applied to space data. However, in addition to investigations such as plasma wave and instability studies, such devices can also make valuable contributions to the development and testing of space plasma diagnostics. One example is the plasma impedance probe developed at NRL. Originally developed as a laboratory diagnostic, the sensor has now been flown on a sounding rocket, is included on a CubeSat experiment, and will be included on the DoD Space Test Program's STP-H6 experiment on the International Space Station. In this talk, we will describe how the laboratory simulation of space plasmas made this development path possible. Work sponsored by the US Naval Research Laboratory Base Program.

BIOSPEX: Biological space experiments, a compendium of life sciences experiments carried on US spacecraft

NASA Technical Reports Server (NTRS)

Anderson, M.; Rummel, J. A. (Editor); Deutsch, S. (Editor)

1979-01-01

United States space life science experiments, encompassing 27 years of experience beginning with sounding rocket flights carrying primates (1948) to the last U.S. spaceflight, the joint US/USSR Apollo Test Project (1975), are presented. The information for each experiment includes Principal Investigators, the program and mission on which it was flown, the specimens used, the objectives, protocol, equipment, results, conclusions, and bibliographic reference citations for publications derived from each experiment.

Improving students’ creative thinking skill through local material-based experiment (LMBE) on protein qualitative test

NASA Astrophysics Data System (ADS)

Supriyanti, F. M. T.; Halimatul, H. S.

2018-05-01

This study aims to enhance chemistry students’ creative thinking skills using material from local resources on protein qualitative test experiment (LMBE). In this study, a quasi experiment method using one group pretest-postest non-equivalen control group design was carried out on the effectiveness of local material-based experiment approach. The data was collected using the test consists of five assay test and student work sheet (LKM). The effectiveness of the local material-based experiment was tested by means of percentage of normalized gain and score percentage of students’ worksheet. Comparison of creative thinking skills pretest and postest scores showed that the implementation of local material- based experiment (LMBE) enhanced students’s creative thinking skills in experiment class with the value of normalized gain (=0,77) at high category, while in control class reached to =0,44 at medium category. In addition, the LKM shown the enhancements of all aspect of creative thinking skills, including fluency, flexibility, and elaboration skills with the score of in experiment class are 0.79; 0.75; and 0.87 at high category, respectively. In contrast, the only the elaboration skill of control group was improved at high category (=0.76), while fluency and flexibility indicators enhanced at medium category (=0.48 and 0.56, respectively).

Advantages and disadvantages : longitudinal vs. repeated cross-section surveys

DOT National Transportation Integrated Search

1979-01-01

Results are described of experiments conducted in Mississippi, California, and Oregon testing the effectiveness of speed control signs in rural school zones and small communities on high-speed, two-lane highways. Signs tested included existing signin...

Development and flight history of SERT 2 spacecraft

NASA Technical Reports Server (NTRS)

Kerslake, William R.; Ignaczak, Louis R.

1992-01-01

A 25-year historical review of the Space Electric Rocket Test 2 (SERT 2) mission is presented. The Agena launch vehicle; the SERT 2 spacecraft; and mission-peculiar spacecraft hardware, including two ion thruster systems, are described. The 3 1/2-year development period, from 1966 to 1970, that was needed to design, fabricate, and qualify the ion thruster system and the supporting spacecraft components, is documented. Major testing of two ion thruster systems and related auxiliary experiments that were conducted in space after the 3 Feb. 1970, launch are reviewed. Extended ion thruster restarts from 1973 to 1981 are reported, in addition to cross-neutralization tests. Tests of a reflector erosion experiment were continued in 1989 to 1991. The continuing performance of spacecraft subsystems, including the solar arrays, over the 1970-1991 period is summarized. Finally, the knowledge of thruster-spacecraft interactions learned from SERT 2 is listed.

Plant growth using EMCS hardware on the ISS.

PubMed

Iversen, Tor-Henning; Fossum, Knut R; Svare, Hakon; Johnsson, Anders; Schiller, Peter

2002-07-01

Under separate contracts with ESA (FUMO and ERM Study) and as a link in the development of the European Modular Cultivation System's (EMCS) functionality and biocompatibility, plant studies have been performed at The Plant Biocentre in Trondheim, Norway. The main goal was to test whether the breadboards containing the major components planned for use in the EMCS would be optimal for space experiments with plant material. The test plans and the experimental set-up for the verification of biocompatibility and biological functionality included the use of a few model plant species including cress (Lepidium sativum L.) and Arabidopsis thaliana. The plants were tested at different developmental levels of morphological and physiological complexity (illumination, life support, humidity control, water supply, observation, short- and long-term plant growth experiments and contamination prevention). Results from the tests show that the EMCS concept is useful for long duration plant growth on the ISS.

Experimental Study of Unshrouded Impeller Pump Stage Sensitivity to Tip Clearance

NASA Technical Reports Server (NTRS)

Williams, Robert W.; Zoladz, Thomas; Storey, Anne K.; Skelley, Stephen E.

2002-01-01

This viewgraph presentation provides information on an experiment. Its objective is to experimentally determine unshrouded impeller performance sensitivity to tip clearance. The experiment included: Determining impeller efficiency at scaled operating conditions in water at MSFC's Pump Test Equipment (PTE) Facility; Testing unshrouded impeller at three different tip clearances; Testing each tip clearance configuration at on- and off-design conditions, and collecting unsteady- and steady-state data in each configuration; Determining impeller efficiency directly using drive line torquemeter and pump inlet and exit total pressure measurements.

Flight-test experience in digital control of a remotely piloted vehicle.

NASA Technical Reports Server (NTRS)

Edwards, J. W.

1972-01-01

The development of a remotely piloted vehicle system consisting of a remote pilot cockpit and a ground-based digital computer coupled to the aircraft through telemetry data links is described. The feedback control laws are implemented in a FORTRAN program. Flight-test experience involving high feedback gain limits for attitude and attitude rate feedback variables, filtering of sampled data, and system operation during intermittent telemetry data link loss is discussed. Comparisons of closed-loop flight tests with analytical calculations, and pilot comments on system operation are included.

Flight experience with a fail-operational digital fly-by-wire control system

NASA Technical Reports Server (NTRS)

Brown, S. R.; Szalai, K. J.

1977-01-01

The NASA Dryden Flight Research Center is flight testing a triply redundant digital fly-by-wire (DFBW) control system installed in an F-8 aircraft. The full-time, full-authority system performs three-axis flight control computations, including stability and command augmentation, autopilot functions, failure detection and isolation, and self-test functions. Advanced control law experiments include an active flap mode for ride smoothing and maneuver drag reduction. This paper discusses research being conducted on computer synchronization, fault detection, fault isolation, and recovery from transient faults. The F-8 DFBW system has demonstrated immunity from nuisance fault declarations while quickly identifying truly faulty components.

Plasma diagnostic development and UHV testing for the ALPHA collaboration at Marquette University

NASA Astrophysics Data System (ADS)

Tharp, T. D.; Alpha Collaboration

2017-10-01

At Marquette, we are developing the next generation of nonneutral plasma diagnostics for the ALPHA experiment at CERN. ALPHA is building a new vertical experiment to test the gravitational interaction of antihydrogen with Earth. This expansion requires significant changes to the design of our plasma diagnostic suites: the next generation of tools must be able to measure plasmas from two directions, and must be capable of operating in a horizontal position. The diagnostic suite includes measurements of plasma density, shape, and temperature. The hardware used includes a MicroChannel Plate (MCP), a Faraday Cup, and an electron gun. In addition, we are building a vacuum chamber to test the viability of 3-d printed components for UHV compatibility, with target pressures of 10-10 mbar.

What good is labeling what's good? A field experimental investigation of parental labeled praise and child compliance.

PubMed

Leijten, Patty; Thomaes, Sander; Orobio de Castro, Bram; Dishion, Thomas J; Matthys, Walter

2016-12-01

There is a need to identify the "effective ingredients" of evidence-based behavior therapies. We tested the effects of one of the most common ingredients in parenting interventions for preventing disruptive child behavior, referred to as labeled praise (e.g., "well done picking up your toys"), which is typically recommended in preference to unlabeled praise (e.g., "well done"). We compared the effects of labeled praise, unlabeled praise, and no praise on child compliance in two experiments. Experiment 1 included 161 4 to 8 year-old community sample children and tested immediate effects of praise. Experiment 2 included 132 3 to 9 year-old children with varying levels of disruptive behavior and tested immediate and two-week effects of praise. In Experiment 1, teaching parents to use labeled praise did not increase immediate child compliance, whereas teaching them to use unlabeled praise did. In Experiment 2, teaching parents to use labeled praise for two weeks reduced disruptive child behavior, but this effect was of a similar magnitude to that for unlabeled praise. Parents preferred the use of unlabeled over labeled praise. These findings suggest that parental praise promotes child compliance, but the addition of labeling the specific positive behavior may not be of incremental value. Copyright © 2016 Elsevier Ltd. All rights reserved.

Pulmonary Function in Flight (PuFF) Experiment

NASA Technical Reports Server (NTRS)

2003-01-01

In this International Space Station (ISS) onboard photo, Expedition Six Science Officer Donald R. Pettit works to set up the Pulmonary Function in Flight (PuFF) experiment hardware in the Destiny Laboratory. Expedition Six is the fourth and final crew to perform the PuFF experiment. The PuFF experiment was developed to better understand what effects long term exposure to microgravity may have on the lungs. The focus is on measuring changes in the everness of gas exchange in the lungs, and on detecting changes in respiratory muscle strength. It allows astronauts to measure blood flow through the lungs, the ability of the lung to take up oxygen, and lung volumes. Each PuFF session includes five lung function tests, which involve breathing only cabin air. For each planned extravehicular (EVA) activity, a crew member performs a PuFF test within one week prior to the EVA. Following the EVA, those crew members perform another test to document the effect of exposure of the lungs to the low-pressure environment of the space suits. This experiment utilizes the Gas Analyzer System for Metabolic Analysis Physiology, or GASMAP, located in the Human Research Facility (HRF), along with a variety of other Puff equipment including a manual breathing valve, flow meter, pressure-flow module, pressure and volume calibration syringes, and disposable mouth pieces.

Flight Flutter Testing of Supersonic Interceptors

NASA Technical Reports Server (NTRS)

Dublin, M.; Peller, R.

1975-01-01

A summary is presented of experiences in connection with flight flutter testing of supersonic interceptors. The planning and operational aspects involved are described along with the difficulties encountered, and the correlation between measurement and theory. Recommendations for future research and development to advance the science of flight flutter testing are included.

US experiments flown on the Soviet biosatellite Cosmos 2044. Volume 1: Mission description, experiments K-7-01 - K-7-15

NASA Technical Reports Server (NTRS)

Connolly, James P. (Editor); Grindeland, Richard E. (Editor); Ballard, Rodney W. (Editor)

1994-01-01

Cosmos 2044 was launched on September 15, 1989, containing radiation dosimetry experiments and a biological payload including two young male rhesus monkeys, ten adult male Wistar rats, insects, amphibians, protozoa, cell cultures, worms, plants and fish. The biosatellite was launched from the Plesetsk Cosmodrome in the Soviet Union for a mission duration of 14 days, as planned. The major research objectives were: (1) Study adaptive response mechanisms of mammals during flight; (2) Study physiological mechanisms underlying vestibular, motor system and brain function in primates during early and later adaptation phases; (3) Study the tissue regeneration processes of mammals; (4) Study the development of single-celled organisms, cell cultures and embryos in microgravity; (5) Study radiation characteristics during the mission and investigate doses, fluxes and spectra of cosmic radiation for various types of shielding. American and Soviet specialists jointly conducted 29 experiments on this mission including extensive preflight and post flight studies with rhesus monkeys, and tissue processing and cell culturing post flight. Biosamples and data were subsequently transferred to the United States. The U.S. responsibilities for this flight included development of flight and ground-based hardware, the preparation of rat tissue sample procedures, the verification testing of hardware and experiment procedures, and the post flight analysis of biospecimens and data for the joint experiments. The U.S. investigations included four primate experiments, 24 rat experiments, and one radiation dosimetry experiment. Three scientists investigated tissue repair during flight for a subgroup of rats injured preflight by surgical intervention. A description of the Cosmos 2044 mission is presented in this report including preflight, on-orbit and post flight activities. The flight and ground-based bioinstrumentation which was developed by the U.S. and U.S.S.R. is also described, along with the associated preflight testing of the U.S. hardware.

ATM test and integration. [Skylab Apollo Telescope Mount

NASA Technical Reports Server (NTRS)

Moore, J. W.; Mitchell, J. R.

1974-01-01

The test and checkout philosophy of the test program for the Skylab ATM module and the overall test flow including in-process, post-manufacturing, vibration, thermal vacuum, and prelaunch checkout activities are described. Capabilities and limitations of the test complex and its use of automation are discussed. Experiences with the organizational principle of using a dedicated test team for all checkout activities are reported. Material on the development of the ATM subsystems, the experimental program and the requirements of the scientific community, and the integration and verification of the complex systems/subsystems of the ATM are presented. The performance of the ATM test program in such areas as alignment, systems and subsystems, contamination control, and experiment operation is evaluated. The conclusions and recommendations resulting from the ATM test program are enumerated.

Comparison of Resource Requirements for a Wind Tunnel Test Designed with Conventional vs. Modern Design of Experiments Methods

NASA Technical Reports Server (NTRS)

DeLoach, Richard; Micol, John R.

2011-01-01

The factors that determine data volume requirements in a typical wind tunnel test are identified. It is suggested that productivity in wind tunnel testing can be enhanced by managing the inference error risk associated with evaluating residuals in a response surface modeling experiment. The relationship between minimum data volume requirements and the factors upon which they depend is described and certain simplifications to this relationship are realized when specific model adequacy criteria are adopted. The question of response model residual evaluation is treated and certain practical aspects of response surface modeling are considered, including inference subspace truncation. A wind tunnel test plan developed by using the Modern Design of Experiments illustrates the advantages of an early estimate of data volume requirements. Comparisons are made with a representative One Factor At a Time (OFAT) wind tunnel test matrix developed to evaluate a surface to air missile.

Myths and Misinformation About Gunshot Wounds may Adversely Affect Proper Treatment.

PubMed

Hafertepen, Stephen C; Davis, James W; Townsend, Ricard N; Sue, Lawrence P; Kaups, Krista L; Cagle, Kathleen M

2015-07-01

Poorly designed experiments and popular media have led to multiple myths about wound ballistics. Some of these myths have been incorporated into the trauma literature as fact and are included in Advanced Trauma Life Support (ATLS). We hypothesized that these erroneous beliefs would be prevalent, even among those providing care for patients with gunshot wounds (GSWs), but could be addressed through education. ATLS course content was reviewed. Several myths involving wound ballistics were identified. Clinically relevant myths were chosen including wounding mechanism, lead poisoning, debridement, and antibiotic use. Subsequently, surgery and emergency medicine services at three different trauma centers were studied. All three sites were busy, urban trauma centers with a significant amount of penetrating trauma. A pre-test was administered prior to a lecture on wound ballistics followed by a post-test. Pre- and post-test scores were compared and correlated with demographic data including ATLS course completion, firearm/ballistics experience, and years of post-graduate medical experience (PGME). One-hundred and fifteen clinicians participated in the study. A mean pre-test score of 34 % improved to 78 % on the post-test with associated improvements in all areas of knowledge (p < 0.001). Years of PGME correlated with higher pre-test score (p = 0.021); however, ATLS status did not (p = 0.774). Erroneous beliefs involving wound ballistics are prevalent even among clinicians who frequently treat victims of GSWs and could lead to inappropriate treatment. Focused education markedly improved knowledge. The ATLS course and manual promulgate some of these myths and should be revised.

The 1980 US/Canada wheat and barley exploratory experiment. Volume 2: Addenda

NASA Technical Reports Server (NTRS)

Bizzell, R. M.; Prior, H. L.; Payne, R. W.; Disler, J. M.

1983-01-01

Three study areas supporting the U.S./Canada Wheat and Barley Exploratory Experiment are discussed including an evaluation of the experiment shakedown test analyst labeling results, an evaluation of the crop proportion estimate procedure 1A component, and the evaluation of spring wheat and barley crop calendar models for the 1979 crop year.

Potential for geophysical experiments in large scale tests.

USGS Publications Warehouse

Dieterich, J.H.

1981-01-01

Potential research applications for large-specimen geophysical experiments include measurements of scale dependence of physical parameters and examination of interactions with heterogeneities, especially flaws such as cracks. In addition, increased specimen size provides opportunities for improved recording resolution and greater control of experimental variables. Large-scale experiments using a special purpose low stress (100MPa).-Author

Vision, Training Hours, and Road Testing Results in Bioptic Drivers

PubMed Central

Dougherty, Bradley E.; Flom, Roanne E.; Bullimore, Mark A.; Raasch, Thomas W.

2015-01-01

Purpose Bioptic telescopic spectacles (BTS) can be used by people with central visual acuity that does not meet the state standards to obtain an unrestricted driver’s license. The purpose of this study was to examine the relationships among visual and demographic factors, training hours, and the results of road testing for bioptic drivers. Methods A retrospective study of patients who received an initial daylight bioptic examination at the Ohio State University and subsequently received a bioptic license was conducted. Data were collected on vision including visual acuity, contrast sensitivity, and visual field. Hours of driver training and results of Highway Patrol road testing were extracted from records. Relationships among vision, training hours, and road testing were analyzed. Results Ninety-seven patients who completed a vision examination between 2004 and 2008 and received daylight licensure with BTS were included. Results of the first Highway Patrol road test were available for 74 patients. The median interquartile range (IQR) hours of training prior to road testing was 21±17 hours, (range of 9 to 75 hours). Candidates without previous licensure were younger (p< 0.001) and had more documented training (p< 0.001). Lack of previous licensure and more training were significantly associated with having failed a portion of the Highway Patrol test and points deducted on the road test. Conclusions New bioptic drivers without previous non-bioptic driving experience required more training and performed more poorly on road testing for licensure than those who had previous non-bioptic licensure. No visual factor was predictive of road testing results after adjustment for previous experience. The hours of training received remained predictive of road testing outcome even with adjustment for previous experience. These results suggest that previous experience and trainer assessments should be investigated as potential predictors of road safety in bioptic drivers in future studies. PMID:25946098

Role of Geology in Science Teaching.

ERIC Educational Resources Information Center

Kolesar, Peter Thomas

1989-01-01

Described is a teacher education course designed to give future elementary school teachers hands-on experience in hypothesis formation and testing. Four science experiences are discussed which involve different earth science principles including: porosity and permeability; freezing and thawing; river discharge and sedimentation; and groundwater…

Experimental traffic control device testing at New Hampshire toll plazas.

DOT National Transportation Integrated Search

2007-06-01

This report includes a description of the testing and evaluation methodology of the E-ZPassSM Purple Light Experiment. Purple lights with : advanced signs were installed as supplemental traffic control devices for northbound and southbound E-Zp...

Development and testing of a unique carousel wind tunnel to experimentally determine the effect of gravity and the interparticle force on the physics of wind-blown particles

NASA Technical Reports Server (NTRS)

Leach, R. N.; Greeley, Ronald; White, Bruce R.; Iversen, James D.

1987-01-01

In the study of planetary aeolian processes the effect of gravity is not readily modeled. Gravity appears in the equations of particle motion along with the interparticle forces but the two are not separable. A wind tunnel that perimits multiphase flow experiments with wind blown particles at variable gravity was built and experiments were conducted at reduced gravity. The equations of particle motion initiation (saltation threshold) with variable gravity were experimentally verified and the interparticle force was separated. A uniquely design Carousel Wind Tunnel (CWT) allows for the long flow distance in a small sized tunnel since the test section if a continuous loop and develops the required turbulent boundary layer. A prototype model of the tunnel where only the inner drum rotates was built and tested in the KC-135 Weightless Wonder 4 zero-g aircraft. Future work includes further experiments with walnut shell in the KC-135 which sharply graded particles of widely varying median sizes including very small particles to see how interparticle force varies with particle size, and also experiments with other aeolian material.

Remote Advanced Payload Test Rig (RAPTR) Portable Payload Test System for the International Space Station (ISS)

NASA Technical Reports Server (NTRS)

Calvert, John; Freas, George, II

2017-01-01

The RAPTR was developed to test ISS payloads for NASA. RAPTR is a simulation of the Command and Data Handling (C&DH) interfaces of the ISS (MIL-STD 1553B, Ethernet and TAXI) and is designed to facilitate rapid testing and deployment of payload experiments to the ISS. The ISS Program's goal is to reduce the amount of time it takes a payload developer to build, test and fly a payload, including payload software. The RAPTR meets this need with its user oriented, visually rich interface. Additionally, the Analog and Discrete (A&D) signals of the following payload types may be tested with RAPTR: (1) EXPRESS Sub Rack Payloads; (2) ELC payloads; (3) External Columbus payloads; (4) External Japanese Experiment Module (JEM) payloads. The automated payload configuration setup and payload data inspection infrastructure is found nowhere else in ISS payload test systems. Testing can be done with minimal human intervention and setup, as the RAPTR automatically monitors parameters in the data headers that are sent to, and come from the experiment under test.

Environmental qualification testing of payload G-534, the Pool Boiling Experiment

NASA Technical Reports Server (NTRS)

Sexton, J. Andrew

1992-01-01

Payload G-534, the prototype Pool Boiling Experiment (PBE), is scheduled to fly on the STS-47 mission in September 1992. This paper describes the purpose of the experiment and the environmental qualification testing program that was used to prove the integrity of the hardware. Component and box level vibration and thermal cycling tests were performed to give an early level of confidence in the hardware designs. At the system level, vibration, thermal extreme soaks, and thermal vacuum cycling tests were performed to qualify the complete design for the expected shuttle environment. The system level vibration testing included three axis sine sweeps and random inputs. The system level hot and cold soak tests demonstrated the hardware's capability to operate over a wide range of temperatures and gave wider latitude in determining which shuttle thermal attitudes were compatible with the experiment. The system level thermal vacuum cycling tests demonstrated the hardware's capability to operate in a convection free environment. A unique environmental chamber was designed and fabricated by the PBE team and allowed most of the environmental testing to be performed within the hardware build laboratory. The completion of the test program gave the project team high confidence in the hardware's ability to function as designed during flight.

Experimental design, power and sample size for animal reproduction experiments.

PubMed

Chapman, Phillip L; Seidel, George E

2008-01-01

The present paper concerns statistical issues in the design of animal reproduction experiments, with emphasis on the problems of sample size determination and power calculations. We include examples and non-technical discussions aimed at helping researchers avoid serious errors that may invalidate or seriously impair the validity of conclusions from experiments. Screen shots from interactive power calculation programs and basic SAS power calculation programs are presented to aid in understanding statistical power and computing power in some common experimental situations. Practical issues that are common to most statistical design problems are briefly discussed. These include one-sided hypothesis tests, power level criteria, equality of within-group variances, transformations of response variables to achieve variance equality, optimal specification of treatment group sizes, 'post hoc' power analysis and arguments for the increased use of confidence intervals in place of hypothesis tests.

STS-73 Flight Day 5

NASA Technical Reports Server (NTRS)

1995-01-01

On this fifth day of the STS-73 sixteen day mission, the crew Cmdr. Kenneth Bowersox, Pilot Kent Rominger, Payload Specialists Albert Sacco and Fred Leslie, and Mission Specialists Kathryn Thornton, Catherine 'Cady' Coleman, and Michael Lopez-Alegria are shown performing several of the spaceborne experiments onboard the United States Microgravity Lab-2 (USML-2). These experiments are downlinked to Mission Control from the Spacelab using the High-Packed Digital Television (HI-PAC) systems onboard the Shuttle. The experiments shown include the Drop Physics Module (DPM) experiment, the Surface Tension Driven Convection Experiment (STDCE), the Protein Crystal Growth (PCG) experiment, and a Hand-Held Diffusion Test Cell experiment. Lopez-Alegria is interviewed in Spanish by two Spanish radio show hosts. Earth views include cloud cover, the Earth's horizon and atmospheric boundary layers, and several oceans.

Shuttle wave experiments. [space plasma investigations: design and instrumentation

NASA Technical Reports Server (NTRS)

Calvert, W.

1976-01-01

Wave experiments on shuttle are needed to verify dispersion relations, to study nonlinear and exotic phenomena, to support other plasma experiments, and to test engineering designs. Techniques based on coherent detection and bistatic geometry are described. New instrumentation required to provide modules for a variety of missions and to incorporate advanced signal processing and control techniques is discussed. An experiment for Z to 0 coupling is included.

Fifty Years of Observing Hardware and Human Behavior

NASA Technical Reports Server (NTRS)

McMann, Joe

2011-01-01

During this half-day workshop, Joe McMann presented the lessons learned during his 50 years of experience in both industry and government, which included all U.S. manned space programs, from Mercury to the ISS. He shared his thoughts about hardware and people and what he has learned from first-hand experience. Included were such topics as design, testing, design changes, development, failures, crew expectations, hardware, requirements, and meetings.

Acceptance testing of the prototype electrometer for the SAMPIE flight experiment

NASA Technical Reports Server (NTRS)

Hillard, G. Barry

1992-01-01

The Solar Array Module Plasma Interaction Experiment (SAMPIE) has two key instruments at the heart of its data acquisition capability. One of these, the electrometer, is designed to measure both ion and electron current from most of the samples included in the experiment. The accuracy requirement, specified by the project's Principal Investigator, is for agreement within 10 percent with a calibrated laboratory instrument. Plasma chamber testing was performed to assess the capabilities of the prototype design. Agreement was determined to be within 2 percent for electron collection and within 3 percent for ion collection.

Experiment definition phase shuttle laboratory. LDRL-10.6 experiment

NASA Technical Reports Server (NTRS)

1976-01-01

The work completed on the experiment definition phase of the shuttle laboratory LDRL 10.6 micrometers experiment from 27 September 1975 to 26 January 1976 was reported. This work included progress in the following areas: (1) optomechanical system: completion of detail drawings, completion of the beryllium subassembly, fabrication, checking, and weighing of approximately 95% of the detailed parts, dry film lubrication of the bearings and gears, and initiation of assembly of the gimbals; (2) optics: update of the detailed optical layout, receipt of nine mirrors and the pre-expander; (3) miscellaneous: delivery of draft material for the final report, completion of optical testing of the 10.6 micrometers receiver, and receipt, assembly, and checkout of NASA test console.

Cognitive factors in the close visual and magnetic particle inspection of welds underwater.

PubMed

Leach, J; Morris, P E

1998-06-01

Underwater close visual inspection (CVI) and magnetic particle inspection (MPI) are major components of the commercial diver's job of nondestructive testing and the maintenance of subsea structures. We explored the accuracy of CVI in Experiment 1 and that of MPI in Experiment 2 and observed high error rates (47% and 24%, respectively). Performance was strongly correlated with embedded figures and visual search tests and was unrelated to length of professional diving experience, formal inspection qualification, or age. Cognitive tests of memory for designs, spatial relations, dotted outlines, and block design failed to correlate with performance. Actual or potential applications of this research include more reliable inspection reporting, increased effectiveness from current inspection techniques, and directions for the refinement of subsea inspection equipment.

Progress on control experiments of flexible structures

NASA Technical Reports Server (NTRS)

Juang, Jer-Nan

1990-01-01

Progress at the NASA Langley Research Center in the area of control experiments for flexible structures is described. First the author presents the experimental results for a linear model which represents slewing maneuvers of a generic space station solar panel carried out to evaluate experimentally some control technologies. Then the status of the rotational/translational maneuvering experiment of a flexible steel panel carried by a translation cart is presented. Finally, experimental results of the NASA minimast testbed using velocity command stepper motors as reaction mass reactors are shown. All the test configurations are briefly described, including actuator and sensor, test setup, and test software. The status of some research activities oriented primarily to the experimental methods for control of flexible structures is presented.

Beef quality labels: A combination of sensory acceptance test, stated willingness to pay, and choice-based conjoint analysis.

PubMed

Meyerding, Stephan G H; Gentz, Maria; Altmann, Brianne; Meier-Dinkel, Lisa

2018-08-01

Consumer perspectives of beef quality are complex, leading to a market that is increasingly differentiating. Thus, ongoing monitoring and assessment of changes in consumer perspectives is essential to identify changing market conditions. Often only credence and search characteristics are evaluated in consumer studies; therefore the object of the present study is to examine consumer preferences and perceptions towards beef steaks, also including experience characteristics, using a mixed methods approach. For this reason, 55 consumers participated in an experiment in Germany, including a sensory acceptance test, stated willingness to pay, and choice-based conjoint analysis (CBCA). Different quality characteristics were included, but a focus on the quality labels of 'dry aged beef', 'Block House beef', and 'Angus beef' was predominant throughout the experiment with the results showing that quality labels significantly increased overall liking as well as the stated willingness to pay. Quality labels were also the one of the most important characteristics in the conjoint analysis, after origin and price. The results of all applied methods are comparable for the characteristic quality label. The combination of sensory acceptance test and CBCA were additionally able to evaluate all three kinds of beef quality characteristics, which could not be evaluated together only using a single method. This suggests that a mixture of methods should be used to gain better knowledge on the true behavior of beef consumers. Experience and credence characteristics, including beef quality labels, present opportunities for future research as well as the potential for determining product and market differentiation. Copyright © 2018 Elsevier Ltd. All rights reserved.

The Economics of Information: A Classroom Experiment.

ERIC Educational Resources Information Center

Netusil, Noelwah R.; Haupert, Michael

1995-01-01

Describes an economics class experiment where students ranked the quality of baked pies according to limited information. The limited sets of information included brand name and packaging only, price only, advertising only, word-of-mouth, and taste test. Discusses signals of quality and consumer decisions. (MJP)

Support for High-Impact Practices: A New Tool for Administrators

ERIC Educational Resources Information Center

Kezar, Adrianna; Holcombe, Elizabeth

2017-01-01

Certain widely tested educational practices have been shown to have a significantly beneficial impact on student learning and success in college. These "high-impact practices" include first-year experiences, common intellectual experiences, learning communities, writing-intensive courses, collaborative assignments and projects,…

Synthesis of Vitamin K Expoxide: An Undergraduate Biochemistry Experiment.

ERIC Educational Resources Information Center

Thierry-Palmer, M.

1984-01-01

Provides procedures for synthesizing and purifying a vitamin K metabolite (2,3-epoxide) to introduce many of the techniques used in lipid biochemistry. Includes typical results obtained as well as an optional experiment designed to test the purity of the epoxide obtained. (JM)

Flight test operations using an F-106B research airplane modified with a wing leading-edge vortex flap

NASA Technical Reports Server (NTRS)

Dicarlo, Daniel J.; Brown, Philip W.; Hallissy, James B.

1992-01-01

Flight tests of an F-106B aircraft equipped with a leading-edge vortex flap, which represented the culmination of a research effort to examine the effectiveness of the flap, were conducted at the NASA Langley Research Center. The purpose of the flight tests was to establish a data base on the use of a wing leading-edge vortex flap as a means to validate the design and analysis methods associated with the development of such a vortical flow-control concept. The overall experiment included: refinements of the design codes for vortex flaps; numerous wind tunnel entries to aid in verifying design codes and determining basic aerodynamic characteristics; design and fabrication of the flaps, structural modifications to the wing tip and leading edges of the test aircraft; development and installation of an aircraft research instrumentation system, including wing and flap surface pressure measurements and selected structural loads measurements; ground-based simulation to assess flying qualities; and finally, flight testing. This paper reviews the operational aspects associated with the flight experiment, which includes a description of modifications to the research airplane, the overall flight test procedures, and problems encountered. Selected research results are also presented to illustrate the accomplishments of the research effort.

Extrapolating Accelerated UV Weathering Data: Perspective From PVQAT Task Group 5 (Presentation)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Miller, D.; Annigoni, E.; Ballion, A.

2015-02-01

Taskgroup 5 (TG5) is concerned with a accelerated aging standard incorporating factors including ultraviolet radiation, temperature, and moisture. Separate experiments are being conducted in support of a test standard via the regional sub-groups in Asia, Europe, and the United States. The authors will describe the objectives and timeline for the TG5 interlaboratory study being directed out of the USA. Qualitative preliminary data from the experiment is presented. To date, the encapsulation transmittance experiment has: replicated behaviors of fielded materials (including specimen location- and formulation additive-specific discoloration); demonstrated coupling between UV aging and temperature; demonstrated that degradation in EVA results frommore » UV- aging; and obtained good qualitative comparison between Xe and UVA-340 sources for EVA. To date, the encapsulation adhesion experiment (using the compressive shear test to quantify strength of attachment) has demonstrated that attachment strength can decrease drastically (>50%) with age; however, early results suggest significant factor (UV, T, RH) dependence. Much remains to be learned about adhesion.« less

Development, field testing, and implementation of improved bridge parapet designs.

DOT National Transportation Integrated Search

2015-03-01

A total of 22 test parapets was constructed as part of this project to evaluate different approaches to address : premature cracking. The experiments included the use of deeper saw cuts through glass fiber reinforced polymer : (GFRP) reinforcement or...

High Reynolds number tests of a Boeing BAC I airfoil in the Langley 0.3-meter transonic cryogenic tunnel

NASA Technical Reports Server (NTRS)

Johnson, W. G., Jr.; Hill, A. S.; Ray, E. J.; Rozendaal, R. A.; Butler, T. W.

1982-01-01

A wind tunnel investigation of an advanced-technology airfoil was conducted in the Langley 0.3-Meter Transonic Cryogenic Tunnel (TCT). This investigation represents the first in a series of NASA/U.X. industry two dimensional airfoil studies to be completed in the Advanced Technology Airfoil Test program. Test temperature was varied from ambient to about 100 K at pressures ranging from about 1.2 to 6.0 atm. Mach number was varied from about 0.40 to 0.80. These variables provided a Reynolds number (based on airfoil chord) range from about .0000044 to .00005. This investigation was specifically designed to: (1) test a Boeing advanced airfoil from low to flight-equivalent Reynolds numbers; (2) provide the industry participant (Boeing) with experience in cryogenic wind-tunnel model design and testing techniques; and (3) demonstrate the suitability of the 0.3-m TCT as an airfoil test facility. All the objectives of the cooperative test were met. Data are included which demonstrate the effects of fixed transition, Mach number, and Reynolds number on the aerodynamic characteristics of the airfoil. Also included are remarks on the model design, the model structural integrity, and the overall test experience.

Visuo-spatial processing and executive functions in children with specific language impairment

PubMed Central

Marton, Klara

2007-01-01

Background Individual differences in complex working memory tasks reflect simultaneous processing, executive functions, and attention control. Children with specific language impairment (SLI) show a deficit in verbal working memory tasks that involve simultaneous processing of information. Aims The purpose of the study was to examine executive functions and visuo-spatial processing and working memory in children with SLI and in their typically developing peers (TLD). Experiment 1 included 40 children with SLI (age=5;3–6;10) and 40 children with TLD (age=5;3–6;7); Experiment 2 included 25 children with SLI (age=8;2–11;2) and 25 children with TLD (age=8;3–11;0). It was examined whether the difficulties that children with SLI show in verbal working memory tasks are also present in visuo-spatial working memory. Methods & Procedures In Experiment 1, children's performance was measured with three visuo-spatial processing tasks: space visualization, position in space, and design copying. The stimuli in Experiment 2 were two widely used neuropsychological tests: the Wisconsin Card Sorting Test — 64 (WCST-64) and the Tower of London test (TOL). Outcomes & Results In Experiment 1, children with SLI performed more poorly than their age-matched peers in all visuo-spatial working memory tasks. There was a subgroup within the SLI group that included children whose parents and teachers reported a weakness in the child's attention control. These children showed particular difficulties in the tasks of Experiment 1. The results support Engle's attention control theory: individuals need good attention control to perform well in visuo-spatial working memory tasks. In Experiment 2, the children with SLI produced more perseverative errors and more rule violations than their peers. Conclusions Executive functions have a great impact on SLI children's working memory performance, regardless of domain. Tasks that require an increased amount of attention control and executive functions are more difficult for the children with SLI than for their peers. Most children with SLI scored either below average or in the low average range on the neuropsychological tests that measured executive functions. PMID:17852522

Research experiments at Hangar L

NASA Technical Reports Server (NTRS)

2000-01-01

Research technician Lisa Ruffa works with a wheat sample that is part of ground testing for the first International Space Station plant experiment, scheduled to fly in October 2001. The payload process testing is one of many studies being performed at the Biological Sciences Branch in the Spaceport Engineering and Technology Directorate at Kennedy Space Center. The branch's operations and research areas include life sciences Space Shuttle payloads, bioregenerative life-support for long-duration spaceflight and environmental/ecological stewardship.

Space Flight Qualification Program for the AMS-2 Commercial Cryocoolers

NASA Technical Reports Server (NTRS)

Shirey, K. A.; Banks, I. S.; Breon, S. R.; Boyle, R. F.; Krebs, Carolyn A. (Technical Monitor)

2002-01-01

The Alpha Magnetic Spectrometer-02 (AMS-02) experiment is a state-of-the-art particle physics detector containing a large superfluid helium-cooled superconducting magnet. Highly sensitive detector plates inside the magnet measure a particle's speed, momentum, charge, and path. The AMS-02 experiment will study the properties and origin of cosmic particles and nuclei including antimatter and dark matter. AMS-02 will be installed on the International Space Station on Utilization Flight-4. The experiment will be run for at least three years. To extend the life of the stored cryogen and minimize temperature gradients around the magnet, four Stirling-cycle Sunpower M87N cryocoolers will be integrated with AMS-02. The cryocooler cold tip will be connected via a flexible strap to the outer vapor cooled shield of the dewar. Initial thermal analysis shows the lifetime of the experiment is increased by a factor of 2.8 with the use of the cryocooler. The AMS-02 project selected the Sunpower M87 cryocoolers and has asked NASA Goddard to qualify the cryocoolers for space flight use. This paper describes the interfaces with the cryocoolers and presents data collected during testing of the two engineering model cryocoolers. Tests include thermal performance characterization and launch vibration testing. Magnetic field compatibility testing will be presented in a separate paper at the conference.

Operational plans for life science payloads - From experiment selection through postflight reporting

NASA Technical Reports Server (NTRS)

Mccollum, G. W.; Nelson, W. G.; Wells, G. W.

1976-01-01

Key features of operational plans developed in a study of the Space Shuttle era life science payloads program are presented. The data describes the overall acquisition, staging, and integration of payload elements, as well as program implementation methods and mission support requirements. Five configurations were selected as representative payloads: (a) carry-on laboratories - medical emphasis experiments, (b) mini-laboratories - medical/biology experiments, (c) seven-day dedicated laboratories - medical/biology experiments, (d) 30-day dedicated laboratories - Regenerative Life Support Evaluation (RLSE) with selected life science experiments, and (e) Biomedical Experiments Scientific Satellite (BESS) - extended duration primate (Type I) and small vertebrate (Type II) missions. The recommended operational methods described in the paper are compared to the fundamental data which has been developed in the life science Spacelab Mission Simulation (SMS) test series. Areas assessed include crew training, experiment development and integration, testing, data-dissemination, organization interfaces, and principal investigator working relationships.

A second generation experiment in fault-tolerant software

NASA Technical Reports Server (NTRS)

Knight, J. C.

1986-01-01

Information was collected on the efficacy of fault-tolerant software by conducting two large-scale controlled experiments. In the first, an empirical study of multi-version software (MVS) was conducted. The second experiment is an empirical evaluation of self testing as a method of error detection (STED). The purpose ot the MVS experiment was to obtain empirical measurement of the performance of multi-version systems. Twenty versions of a program were prepared at four different sites under reasonably realistic development conditions from the same specifications. The purpose of the STED experiment was to obtain empirical measurements of the performance of assertions in error detection. Eight versions of a program were modified to include assertions at two different sites under controlled conditions. The overall structure of the testing environment for the MVS experiment and its status are described. Work to date in the STED experiment is also presented.

Mission requirements CSM-111/DM-2 Apollo/Soyuz test project

NASA Technical Reports Server (NTRS)

Blackmer, S. M.

1974-01-01

Test systems are developed for rendezvous and docking of manned spacecraft and stations that are suitable for use as a standard international system. This includes the rendezvous and docking of Apollo and Soyuz spacecraft, and crew transfer. The conduct of the mission will include: (1) testing of compatible rendezvous systems in orbit; (2) testing of universal docking assemblies; (3) verifying the techniques for transfer of cosmonauts and astronauts; (4) performing certain activities by U.S.A. and U.S.S.R. crews in joint flight; and (5) gaining of experience in conducting joint flights by U.S.A. and U.S.S.R. spacecraft, including, in case of necessity, rendering aid in emergency situations.

Forest Herbicide Washoff From Foliar Applications

Treesearch

J.L. Michael; Kevin L. Talley; H.C. Fishburn

1992-01-01

Field and laboratory experiments were conducted to develop and test methods for determining washoff of foliar applied herbicides typically used in forestry in the South.Preliminary results show good agreement between results of laboratory methods used and observations from field experiments on actual precipitation events. Methods included application of...

Controlled experiments for dense gas diffusion: Experimental design and execution, model comparison

DOE Office of Scientific and Technical Information (OSTI.GOV)

Egami, R.; Bowen, J.; Coulombe, W.

1995-07-01

An experimental baseline CO2 release experiment at the DOE Spill Test Facility on the Nevada Test Site in Southern Nevada is described. This experiment was unique in its use of CO2 as a surrogate gas representative of a variety of specific chemicals. Introductory discussion places the experiment in historical perspective. CO2 was selected as a surrogate gas to provide a data base suitable for evaluation of model scenarios involving a variety of specific dense gases. The experiment design and setup are described, including design rationale and quality assurance methods employed. Resulting experimental data are summarized. Data usefulness is examined throughmore » a preliminary comparison of experimental results with simulations performed using the SLAV and DEGADIS dense gas models.« less

Development of Next Generation Memory Test Experiment for Deployment on a Small Satellite

NASA Technical Reports Server (NTRS)

MacLeod, Todd; Ho, Fat D.

2012-01-01

The original Memory Test Experiment successfully flew on the FASTSAT satellite launched in November 2010. It contained a single Ramtron 512K ferroelectric memory. The memory device went through many thousands of read/write cycles and recorded any errors that were encountered. The original mission length was schedule to last 6 months but was extended to 18 months. New opportunities exist to launch a similar satellite and considerations for a new memory test experiment should be examined. The original experiment had to be designed and integrated in less than two months, so the experiment was a simple design using readily available parts. The follow-on experiment needs to be more sophisticated and encompass more technologies. This paper lays out the considerations for the design and development of this follow-on flight memory experiment. It also details the results from the original Memory Test Experiment that flew on board FASTSAT. Some of the design considerations for the new experiment include the number and type of memory devices to be used, the kinds of tests that will be performed, other data needed to analyze the results, and best use of limited resources on a small satellite. The memory technologies that are considered are FRAM, FLASH, SONOS, Resistive Memory, Phase Change Memory, Nano-wire Memory, Magneto-resistive Memory, Standard DRAM, and Standard SRAM. The kinds of tests that could be performed are read/write operations, non-volatile memory retention, write cycle endurance, power measurements, and testing Error Detection and Correction schemes. Other data that may help analyze the results are GPS location of recorded errors, time stamp of all data recorded, radiation measurements, temperature, and other activities being perform by the satellite. The resources of power, volume, mass, temperature, processing power, and telemetry bandwidth are extremely limited on a small satellite. Design considerations must be made to allow the experiment to not interfere with the satellite s primary mission.

Overview and First Results of an In-situ Stimulation Experiment in Switzerland

NASA Astrophysics Data System (ADS)

Amann, F.; Gischig, V.; Doetsch, J.; Jalali, M.; Valley, B.; Evans, K. F.; Krietsch, H.; Dutler, N.; Villiger, L.

2017-12-01

A decameter-scale in-situ stimulation and circulation (ISC) experiment is currently being conducted at the Grimsel Test Site in Switzerland with the objective of improving our understanding of key seismo-hydro-mechanical coupled processes associated with high pressure fluid injections in a moderately fractured crystalline rock mass. The ISC experiment activities aim to support the development of EGS technology by 1) advancing the understanding of fundamental processes that occur within the rock mass in response to relatively large-volume fluid injections at high pressures, 2) improving the ability to estimate and model induced seismic hazard and risks, 3) assessing the potential of different injection protocols to keep seismic event magnitudes below an acceptable threshold, 4) developing novel monitoring and imaging techniques for pressure, temperature, stress, strain and displacement as well as geophysical methods such as ground penetration radar, passive and active seismic and 5) generating a high-quality benchmark datasets that facilitates the development and validation of numerical modelling tools. The ISC experiment includes six fault slip and five hydraulic fracturing experiments at an intermediate scale (i.e. 20*20*20m) at 480m depth, which allows high resolution monitoring of the evolution of pore pressure in the stimulated fault zone and the surrounding rock matrix, fault dislocations including shear and dilation, and micro-seismicity in an exceptionally well characterized structural setting. In February 2017 we performed the fault-slip experiments on interconnected faults. Subsequently an intense phase of post-stimulation hydraulic characterization was performed. In Mai 2017 we performed hydraulic fracturing tests within test intervals that were free of natural fractures. In this contribution we give an overview and show first results of the above mentioned stimulation tests.

Biosphere 2 test module: A ground-based sunlight-driven prototype of a closed ecological life support system

NASA Astrophysics Data System (ADS)

Nelson, Mark; Leigh, Linda; Alling, Abigail; MacCallum, Taber; Allen, John; Alvarez-Romo, Norberto

Constructed in 1986, the Biosphere 2 Test Module has been used since the end of that year for closed ecological systems experiments. It is the largest closed ecological facility ever built, with a sealed variable volume of some 480 cubic meters. It is built with a skin of steel spaceframes with double-laminated glass panels admitting about 65 percent Photosynthetically Active Radiation (PAR). The floor is of welded steel and there is an underground atmospheric connection via an air duct to a variable volume chamber (``lung'') permitting expansion and contraction of the Test Module's air volume caused by changes in temperature and barometric pressure, which causes a slight positive pressure from inside the closed system to the outside thereby insuring that the very small leakage rate is outward. Several series of closed ecological system investigations have been carried out in this facility. One series of experiments investigated the dynamics of higher plants and associated soils with the atmosphere under varying light and temperature conditions. Another series of experiments included one human in the closed system for three, five and twenty-one days. During these experiments the Test Module had subsystems which completely recycled its water and atmosphere; all the human dietary needs were produced within the facility, and all wastes were recycled using a marsh plant/microbe system. Other experiments have examined the capability of individual component systems used, such as the soil bed reactors, to eliminate experimentally introduced trace gases. Analytic systems developed for these experiments include continuous monitors of eleven atmospheric gases in addition to the complete gas chromatography mass spectrometry (GCMS) examinations of potable, waste system and irrigation water quality.

Intelligent structures technology

NASA Astrophysics Data System (ADS)

Crawley, Edward F.

1991-07-01

Viewgraphs on intelligent structures technology are presented. Topics covered include: embedding electronics; electrical and mechanical compatibility; integrated circuit chip packaged for embedding; embedding devices within composite structures; test of embedded circuit in G/E coupon; temperature/humidity/bias test; single-chip microcomputer control experiment; and structural shape determination.

Intelligent structures technology

NASA Technical Reports Server (NTRS)

Crawley, Edward F.

1991-01-01

Viewgraphs on intelligent structures technology are presented. Topics covered include: embedding electronics; electrical and mechanical compatibility; integrated circuit chip packaged for embedding; embedding devices within composite structures; test of embedded circuit in G/E coupon; temperature/humidity/bias test; single-chip microcomputer control experiment; and structural shape determination.

Mass Trapping for Anastrepha suspensa

USDA-ARS?s Scientific Manuscript database

ABSTRACT In field tests conducted in south Florida to test grape juice as an alternative inexpensive bait for Anastrepha suspensa Loew, high numbers of Zaprionus indianus Gupta were captured in traps baited with aqueous grape juice. These experiments included comparisons of grape juice with standard...

The confrontation between general relativity and experiment

NASA Technical Reports Server (NTRS)

Will, C. M.

1980-01-01

Experiments that test the foundations of gravitation theory in terms of the Einstein equivalence principle are discussed along with solar system tests of general relativity at the post-Newtonian level. These include classical (light-deflection, time delay and perihelion shift) tests as well as tests of the strong equivalence principle. The binary pulsar is discussed as an extra-solar-system gravitational testing ground, and attention is given to the multipolarity of the waves and the amount of radiation damping. The mass function, periastron shift, redshift-Doppler parameter and rate of change of the orbit period (Pb) of the binary pulsar are also considered, and it is suggested that the measurement of Pb represents the first observation of the effects of gravitational radiation.

Review of Artificial Abrasion Test Methods for PV Module Technology

DOE Office of Scientific and Technical Information (OSTI.GOV)

Miller, David C.; Muller, Matt T.; Simpson, Lin J.

This review is intended to identify the method or methods--and the basic details of those methods--that might be used to develop an artificial abrasion test. Methods used in the PV literature were compared with their closest implementation in existing standards. Also, meetings of the International PV Quality Assurance Task Force Task Group 12-3 (TG12-3, which is concerned with coated glass) were used to identify established test methods. Feedback from the group, which included many of the authors from the PV literature, included insights not explored within the literature itself. The combined experience and examples from the literature are intended tomore » provide an assessment of the present industry practices and an informed path forward. Recommendations toward artificial abrasion test methods are then identified based on the experiences in the literature and feedback from the PV community. The review here is strictly focused on abrasion. Assessment methods, including optical performance (e.g., transmittance or reflectance), surface energy, and verification of chemical composition were not examined. Methods of artificially soiling PV modules or other specimens were not examined. The weathering of artificial or naturally soiled specimens (which may ultimately include combined temperature and humidity, thermal cycling and ultraviolet light) were also not examined. A sense of the purpose or application of an abrasion test method within the PV industry should, however, be evident from the literature.« less

Conducting Closed Habitation Experiments: Experience from the Lunar Mars Life Support Test Project

NASA Technical Reports Server (NTRS)

Barta, Daniel J.; Edeen, Marybeth A.; Henninger, Donald L.

2004-01-01

The Lunar-Mars Life Support Test Project (LMLSTP) was conducted from 1995 through 1997 at the National Aeronautics and Space Administration s (NASA) Johnson Space Center (JSC) to demonstrate increasingly longer duration operation of integrated, closed-loop life support systems that employed biological and physicochemical techniques for water recycling, waste processing, air revitalization, thermal control, and food production. An analog environment for long-duration human space travel, the conditions of isolation and confinement also enabled studies of human factors, medical sciences (both physiology and psychology) and crew training. Four tests were conducted, Phases I, II, IIa and III, with durations of 15, 30,60 and 91 days, respectively. The first phase focused on biological air regeneration, using wheat to generate enough oxygen for one experimental subject. The systems demonstrated in the later phases were increasingly complex and interdependent, and provided life support for four crew members. The tests were conducted using two human-rated, atmospherically-closed test chambers, the Variable Pressure Growth Chamber (VPGC) and the Integrated Life Support Systems Test Facility (ILSSTF). Systems included test articles (the life support hardware under evaluation), human accommodations (living quarters, kitchen, exercise equipment, etc.) and facility systems (emergency matrix system, power, cooling, etc.). The test team was managed by a lead engineer and a test director, and included test article engineers responsible for specific systems, subsystems or test articles, test conductors, facility engineers, chamber operators and engineering technicians, medical and safety officers, and science experimenters. A crew selection committee, comprised of psychologists, engineers and managers involved in the test, evaluated male and female volunteers who applied to be test subjects. Selection was based on the skills mix anticipated for each particular test, and utilized information from psychological and medical testing, data on the knowledge, experience and skills of the applicants, and team building exercises. The design, development, buildup and operation of test hardware and documentation followed the established NASA processes and requirements for test buildup and operation.

Conducting Closed Habitation Experiments: Experience from the Lunar Mars Life Support Test Project

NASA Technical Reports Server (NTRS)

Barta, Daniel J.; Edeen, Marybeth A.; Henninger, Donald L.

2006-01-01

The Lunar-Mars Life Support Test Project (LMLSTP) was conducted from 1995 through 1997 at the National Aeronautics and Space Administration s (NASA) Johnson Space Center (JSC) to demonstrate increasingly longer duration operation of integrated, closed-loop life support systems that employed biological and physicochemical techniques for water recycling, waste processing, air revitalization, thermal control, and food production. An analog environment for long-duration human space travel, the conditions of isolation and confinement also enabled studies of human factors, medical sciences (both physiology and psychology) and crew training. Four tests were conducted, Phases I, II, IIa and III, with durations of 15, 30, 60 and 91 days, respectively. The first phase focused on biological air regeneration, using wheat to generate enough oxygen for one experimental subject. The systems demonstrated in the later phases were increasingly complex and interdependent, and provided life support for four crew members. The tests were conducted using two human-rated, atmospherically-closed test chambers, the Variable Pressure Growth Chamber (VPGC) and the Integrated Life Support Systems Test Facility (ILSSTF). Systems included test articles (the life support hardware under evaluation), human accommodations (living quarters, kitchen, exercise equipment, etc.) and facility systems (emergency matrix system, power, cooling, etc.). The test team was managed by a lead engineer and a test director, and included test article engineers responsible for specific systems, subsystems or test articles, test conductors, facility engineers, chamber operators and engineering technicians, medical and safety officers, and science experimenters. A crew selection committee, comprised of psychologists, engineers and managers involved in the test, evaluated male and female volunteers who applied to be test subjects. Selection was based on the skills mix anticipated for each particular test, and utilized information from psychological and medical testing, data on the knowledge, experience and skills of the applicants, and team building exercises. The design, development, buildup and operation of test hardware and documentation followed the established NASA processes and requirements for test buildup and operation.

Lorentz and CPT Tests with Atoms

NASA Astrophysics Data System (ADS)

Vargas Silva, Arnaldo J.

The prospects for using atomic-spectroscopy experiments to test Lorentz and CPT symmetry are investigated. Phenomenological models for Lorentz violation studied in this work include ones with contributions from all quadratic operators for a Dirac fermion in the Lagrange density of the Standard-Model Extension (SME), without restriction on the operator mass dimension. The systems considered include atoms composed of conventional matter, antimatter, and second-generation particles. Generic expressions for the Lorentz-violating energy shifts applicable to a broad range of atomic transitions are obtained. Signals for Lorentz violation that can in principle be studied in spectroscopic experiments are identified from the theoretical corrections to the spectrum. Some of these signals include sidereal and annual variations of atomic transition frequencies measured in a laboratory on the surface of the Earth. Other possibilities include effects produced by changing the orientation of the applied magnetic field or by realizing space-based experiments. Discrepancies in the experimental values for fundamental constants and energy levels based on self-consistent predictions from the Standard Model also offer potential signals for Lorentz violation. The sensitivities of different experiments to distinct sets of coefficients for Lorentz violation are considered. Using atoms composed of different particle species allows measurements of coefficients for Lorentz violation in different fermion sectors of the SME. Experiments comparing hydrogen and antihydrogen can discriminate between coefficients for Lorentz violation that are associated with CPT-odd or CPT-even operators. Additionally, certain systems and transitions are more sensitive to nonminimal operators, while others are particularly sensitive to minimal ones.

Pre-flight sensorimotor adaptation protocols for suborbital flight.

PubMed

Shelhamer, Mark; Beaton, Kara

2012-01-01

Commercial suborbital flights, which include 3-5 minutes of 0 g between hyper-g launch and landing phases, will present suborbital passengers with a challenging sensorimotor experience. Based on the results of neurovestibular research in parabolic and orbital flight, and the anticipated wide range of fitness and experience levels of suborbital passengers, neurovestibular disturbances are likely to be problematic in this environment. Pre-flight adaptation protocols might alleviate some of these issues. Therefore, we describe a set of sensorimotor tests to evaluate passengers before suborbital flight, including assessment of the angular vestibulo-ocular reflex (VOR), ocular skew and disconjugate torsion, subjective visual vertical, and roll vection. Performance on these tests can be examined for correlations with in-flight experience, such as motion sickness, disorientation, and visual disturbances, based on questionnaires and cabin video recordings. Through an understanding of sensorimotor adaptation to parabolic and orbital flight, obtained from many previous studies, we can then suggest appropriate pre-flight adaptation procedures.

Using the tritium plasma experiment to evaluate ITER PFC safety

NASA Astrophysics Data System (ADS)

Longhurst, Glen R.; Anderl, Robert A.; Bartlit, John R.; Causey, Rion A.; Haines, John R.

1993-06-01

The Tritium Plasma Experiment was assembled at Sandia National Laboratories, Livermore and is being moved to the Tritium Systems Test Assembly facility at Los Alamos National Laboratory to investigate interactions between dense plasmas at low energies and plasma-facing component materials. This apparatus has the unique capabilty of replicating plasma conditions in a tokamak divertor with particle flux densities of 2 × 1023 ions/m2.s and a plasma temperature of about 15 eV using a plasma that includes tritium. An experimental program has been initiated using the Tritium Plasma Experiment to examine safety issues related to tritium in plasma-facing components, particularly the ITER divertor. Those issues include tritium retention and release characteristics, tritium permeation rates and transient times to coolant streams, surface modification and erosion by the plasma, the effects of thermal loads and cycling, and particulate production. An industrial consortium led by McDonnell Douglas will design and fabricate the test fixtures.

Nozzle Initiative Industry Advisory Committee on Standardization of Carbon-Phenolic Test Methods and Specifications

NASA Technical Reports Server (NTRS)

Bull, William B. (Compiler); Pinoli, Pat C. (Compiler); Upton, Cindy G. (Compiler); Day, Tony (Compiler); Hill, Keith (Compiler); Stone, Frank (Compiler); Hall, William B.

1994-01-01

This report is a compendium of the presentations of the 12th biannual meeting of the Industry Advisory Committee under the Solid Propulsion Integrity Program. A complete transcript of the welcoming talks is provided. Presentation outlines and overheads are included for the other sessions: SPIP Overview, Past, Current and Future Activity; Test Methods Manual and Video Tape Library; Air Force Developed Computer Aided Cure Program and SPC/TQM Experience; Magneto-Optical mapper (MOM), Joint Army/NASA program to assess composite integrity; Permeability Testing; Moisture Effusion Testing by Karl Fischer Analysis; Statistical Analysis of Acceptance Test Data; NMR Phenolic Resin Advancement; Constituent Testing Highlights on the LDC Optimization Program; Carbon Sulfur Study, Performance Related Testing; Current Rayon Specifications and Future Availability; RSRM/SPC Implementation; SRM Test Methods, Delta/Titan/FBM/RSRM; and Open Forum on Performance Based Acceptance Testing -- Industry Experience.

Personal Narratives of Genetic Testing: Expectations, Emotions, and Impact on Self and Family.

PubMed

Anderson, Emily E; Wasson, Katherine

2015-01-01

The stories in this volume shed light on the potential of narrative inquiry to fill gaps in knowledge, particularly given the mixed results of quantitative research on patient views of and experiences with genetic and genomic testing. Published studies investigate predictors of testing (particularly risk perceptions and worry); psychological and behavioral responses to testing; and potential impact on the health care system (e.g., when patients bring DTC genetic test results to their primary care provider). Interestingly, these themes did not dominate the narratives published in this issue. Rather, these narratives included consistent themes of expectations and looking for answers; complex emotions; areas of contradiction and conflict; and family impact. More narrative research on patient experiences with genetic testing may fill gaps in knowledge regarding how patients define the benefits of testing, changes in psychological and emotional reactions to test results over time, and the impact of testing on families.

Safety Performance of Small Lithium-Ion Cells in High Voltage Batteries

NASA Technical Reports Server (NTRS)

Cowles, Philip R.; Darcy, Eric C.; Davies, Frank J.; Jeevarajan, Judith A.; Spurrett, Robert P.

2003-01-01

Topics covered include: Small-cell EAPU work done by NASA-JSC & COM DEV; Looking at safety features (short circuit protection - PTCs); Early tests showed that long strings do not withstand short circuit; a) Some PTCs experience large negative voltages; b) Destructive results. Solution: group cells into shorter substrings, with bypass diodes Work included: a) Tests with single cells shorted; b) Tests with single cells with imposed-negative voltages; c) 6s, 7s and 8s string shorts; and d) Tests with protection scheme in place, on 12s and 41s x 5p.

Measurements by a Vector Network Analyzer at 325 to 508 GHz

NASA Technical Reports Server (NTRS)

Fung, King Man; Samoska, Lorene; Chattopadhyay, Goutam; Gaier, Todd; Kangaslahti, Pekka; Pukala, David; Lau, Yuenie; Oleson, Charles; Denning, Anthony

2008-01-01

Recent experiments were performed in which return loss and insertion loss of waveguide test assemblies in the frequency range from 325 to 508 GHz were measured by use of a swept-frequency two-port vector network analyzer (VNA) test set. The experiments were part of a continuing effort to develop means of characterizing passive and active electronic components and systems operating at ever increasing frequencies. The waveguide test assemblies comprised WR-2.2 end sections collinear with WR-3.3 middle sections. The test set, assembled from commercially available components, included a 50-GHz VNA scattering- parameter test set and external signal synthesizers, augmented with recently developed frequency extenders, and further augmented with attenuators and amplifiers as needed to adjust radiofrequency and intermediate-frequency power levels between the aforementioned components. The tests included line-reflect-line calibration procedures, using WR-2.2 waveguide shims as the "line" standards and waveguide flange short circuits as the "reflect" standards. Calibrated dynamic ranges somewhat greater than about 20 dB for return loss and 35 dB for insertion loss were achieved. The measurement data of the test assemblies were found to substantially agree with results of computational simulations.

RERTR-10 Irradiation Summary Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

D. M. Perez

2011-05-01

The Reduced Enrichment for Research and Test Reactor (RERTR) experiment RERTR-10 was designed to further test the effectiveness of modified fuel/clad interfaces in monolithic fuel plates. The experiment was conducted in two campaigns: RERTR-10A and RERTR-10B. The fuel plates tested in RERTR-10A were all fabricated by Hot Isostatic Pressing (HIP) and were designed to evaluate the effect of various Si levels in the interlayer and the thickness of the Zr interlayer (0.001”) using 0.010” and 0.020” nominal foil thicknesses. The fuel plates in RERTR-10B were fabricated by Friction Bonding (FB) with two different thickness Si layers and Nb and Zrmore » diffusion barriers.1 The following report summarizes the life of the RERTR-10A/B experiment through end of irradiation, including as-run neutronic analysis results, thermal analysis results and hydraulic testing results.« less

Ground vibration test of the laminar flow control JStar airplane

NASA Technical Reports Server (NTRS)

Kehoe, M. W.; Cazier, F. W., Jr.; Ellison, J. F.

1985-01-01

A ground vibration test was conducted on a Lockheed JetStar airplane that had been modified for the purpose of conducting laminar flow control experiments. The test was performed prior to initial flight flutter tests. Both sine-dwell and single-point-random excitation methods were used. The data presented include frequency response functions and a comparison of mode frequencies and mode shapes from both methods.

The Shock and Vibration Bulletin. Part 2. Model Test and Analysis, Testing Techniques, Machinery Dynamics, Isolation and Damping, Structural Dynamics

DTIC Science & Technology

1986-08-01

each subsystem wist include more than a set of rigid body and normal modes to properly represent the dynamics of the entire system. Various types of...MCM 1 AUGMENTATION HETNO-MrifaOII FIELD TflACKER »f Tl BASIC EXPERIMENT Figure 3. Dynamics augmentation experiment. i i mnc...Villeurbanne - France Today the dynamic behavior of rotors must be predicted with the greatest care. This work deals with the influence of disc flexi

Apollo Soyuz test project, USA-USSR. [mission plan of spacecraft docking

NASA Technical Reports Server (NTRS)

1975-01-01

The mission plan of the docking of a United States Apollo and a Soviet Union Soyuz spacecraft in Earth orbit to test compatible rendezvous and docking equipment and procedures is presented. Space experiments conducted jointly by the astronauts and cosmonauts during the joint phase of the mission as well as experiments performed solely by the U.S. astronauts and spread over the nine day span of the flight are included. Biographies of the astronauts and cosmonauts are given.

UNDERSTANDINGS OF BSCS BIOLOGY STUDENTS AS DETERMINED BY INSTRUCTIONAL TESTS.

ERIC Educational Resources Information Center

ROBINSON, JAMES T.

EIGHT INSTRUCTIONAL TESTS SPANNED THE CURRICULUM OF ONE YEAR OF BIOLOGY STUDY. THE FIRST CONCERNED THE NATURE OF SCIENCE INCLUDED 4 AREAS OF EMPHASIS--THE NATURE AND FUNCTION OF HYPOTHESIS, THE IDEA OF CONTROLS IN EXPERIMENTS, INTERPRETATION OF GRAPHED DATA, AND THE NATURE OF DATA. THE SECOND TEST WAS DESIGNED TO SHOW AN UNDERSTANDING OF…

Mission Possible: BioMedical Experiments on the Space Shuttle

NASA Technical Reports Server (NTRS)

Bopp, E.; Kreutzberg, K.

2011-01-01

Biomedical research, both applied and basic, was conducted on every Shuttle mission from 1981 to 2011. The Space Shuttle Program enabled NASA investigators and researchers from around the world to address fundamental issues concerning living and working effectively in space. Operationally focused occupational health investigations and tests were given priority by the Shuttle crew and Shuttle Program management for the resolution of acute health issues caused by the rigors of spaceflight. The challenges of research on the Shuttle included: limited up and return mass, limited power, limited crew time, and requirements for containment of hazards. The sheer capacity of the Shuttle for crew and equipment was unsurpassed by any other launch and entry vehicle and the Shuttle Program provided more opportunity for human research than any program before or since. To take advantage of this opportunity, life sciences research programs learned how to: streamline the complicated process of integrating experiments aboard the Shuttle, design experiments and hardware within operational constraints, and integrate requirements between different experiments and with operational countermeasures. We learned how to take advantage of commercial-off-the-shelf hardware and developed a hardware certification process with the flexibility to allow for design changes between flights. We learned the importance of end-to-end testing for experiment hardware with humans-in-the-loop. Most importantly, we learned that the Shuttle Program provided an excellent platform for conducting human research and for developing the systems that are now used to optimize research on the International Space Station. This presentation will include a review of the types of experiments and medical tests flown on the Shuttle and the processes that were used to manifest and conduct the experiments. Learning Objective: This paper provides a description of the challenges related to launching and implementing biomedical experiments aboard the Space Shuttle.

Will the "Real" Proficiency Standard Please Stand Up?

ERIC Educational Resources Information Center

Baron, Joan Boykoff; And Others

Connecticut's experience with four different standard-setting methods regarding multiple choice proficiency tests is described. The methods include Angoff, Nedelsky, Borderline Group, and Contrasting Groups Methods. All Connecticut ninth graders were administered proficiency tests in reading, language arts, and mathematics. As soon as final test…

The Experimental Design Ability Test (EDAT)

ERIC Educational Resources Information Center

Sirum, Karen; Humburg, Jennifer

2011-01-01

Higher education goals include helping students develop evidence based reasoning skills; therefore, scientific thinking skills such as those required to understand the design of a basic experiment are important. The Experimental Design Ability Test (EDAT) measures students' understanding of the criteria for good experimental design through their…

Experimental Study of Grit Particle Enhancement in Non-Shock Ignition

NASA Astrophysics Data System (ADS)

Browning, Richard V.; Peterson, Paul D.; Roemer, Edward L.; Oldenborg, Michael R.; Thompson, Darla G.; Deluca, Racci

2006-07-01

The drop weight impact test is the most commonly used configuration for evaluating sensitivity of explosives to non-shock ignition. Although developed 60 years ago and widely used both as a material compression test and as a test bed for understanding the ignition process itself, little is known about the flow mechanisms or involvement of grit particles as sensitizing agents. In this paper, we present the results of a series of experiments designed to study the flow mechanisms and events leading up to ignition. The experimental configuration used involves two pellet sizes, 3 and 5 mm in diameter, tested with three conditions: (1) smooth steel anvils, (2) standard flint sandpaper, and (3) shed grit particles loaded between the steel anvils and the pellet faces. Diagnostics include optical micrographs, and scanning electron micrographs. Un-reacted samples show a variety of morphologies, including what appear to be quenched reaction sites, even at very low drop heights. Quasi-static crushing experiments were also done to quantify load-time histories.

Experimental Study of Grit Particle Enhancement in Non-Shock Ignition of PBX 9501

NASA Astrophysics Data System (ADS)

Peterson, Paul

2005-07-01

The drop weight impact test is the most commonly used configuration for evaluating sensitivity of explosives to non-shock ignition. Although developed 60 years ago and widely used both as a material compression test and as a test bed for understanding the ignition process itself, little is known about the flow mechanisms or involvement of grit particles as sensitizing agents. In this paper we present the results of a series of experiments designed to study the flow mechanisms and events leading up to ignition. The experimental configuration used involves two pellet sizes, 3 and 5 mm in diameter, tested in three conditions, (1) with smooth steel anvils, (2) with standard flint sandpaper, and (3) with shed grit particles loaded between the steel anvils and the pellet faces. Diagnostics include optical micrographs, and scanning electron micrographs. Un-reacted samples show a variety of morphologies, including what appear to be quenched reaction sites, even at very low drop heights. Quasi-static crushing experiments were also done to quantify load-time histories.

Validation Study of Unnotched Charpy and Taylor-Anvil Impact Experiments using Kayenta

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kamojjala, Krishna; Lacy, Jeffrey; Chu, Henry S.

2015-03-01

Validation of a single computational model with multiple available strain-to-failure fracture theories is presented through experimental tests and numerical simulations of the standardized unnotched Charpy and Taylor-anvil impact tests, both run using the same material model (Kayenta). Unnotched Charpy tests are performed on rolled homogeneous armor steel. The fracture patterns using Kayenta’s various failure options that include aleatory uncertainty and scale effects are compared against the experiments. Other quantities of interest include the average value of the absorbed energy and bend angle of the specimen. Taylor-anvil impact tests are performed on Ti6Al4V titanium alloy. The impact speeds of the specimenmore » are 321 m/s and 393 m/s. The goal of the numerical work is to reproduce the damage patterns observed in the laboratory. For the numerical study, the Johnson-Cook failure model is used as the ductile fracture criterion, and aleatory uncertainty is applied to rate-dependence parameters to explore its effect on the fracture patterns.« less

Study of airborne science experiment management concepts for application to space shuttle, volume 2

NASA Technical Reports Server (NTRS)

Mulholland, D. R.; Reller, J. O., Jr.; Neel, C. B.; Haughney, L. C.

1973-01-01

Airborne research management and shuttle sortie planning at the Ames Research Center are reported. Topics discussed include: basic criteria and procedures for the formulation and approval of airborne missions; ASO management structure and procedures; experiment design, development, and testing aircraft characteristics and experiment interfaces; information handling for airborne science missions; mission documentation requirements; and airborne science methods and shuttle sortie planning.

Childhood experiences and psychosocial influences on HIV risk among adolescent Latinas in southern California.

PubMed

Newcomb, Michael D; Locke, Thomas F; Goodyear, Rodney K

2003-08-01

This study determined how adverse childhood experiences influenced risky sexual behavior in a community sample of Latina adolescents in Los Angeles (N = 904) within a modified ecodevelopmental perspective. Psychosocial, sociocultural, and environmental mediators of the relations between childhood experiences and risky sexual behavior were tested. Many direct and mediated paths were revealed using structural equation modeling. Childhood maltreatment was associated with risk sexual practices, including more partners, less condom use, more frequent intercourse, and less HIV testing. Drug use and general self-efficacy mediated several relationships. Reducing childhood maltreatment reduced HIV risk and improved psychosocial functioning. Many factors tested did not influence HIV risk. Much of what is known about HIV risk among other populations may not apply to young Latina women.

Mere odor exposure learning in the rat neonate immediately after birth and one day later

PubMed Central

Miller, Stacie S.; Spear, Norman E.

2011-01-01

Rat pups are more resistant to retroactive associative interference 3 hrs after birth than 24 hours later (Cheslock, Sanders, & Spear, 2004). The present experiments tested the effect of age, retention interval and dam presence during the retention interval on odor-induced motor activity subsequent to mere odor exposure. Rats were exposed to an hour of odor immediately after birth or approximately one day later and tested after a given retention interval (3 hrs or 27 hrs [Exp 1]; 0, 30, 75, or 180 min [Exp. 2]). They spent the retention interval either in the presence or absence of a foster dam (Exp. 1 and 3). After the retention interval, pups were tested in a four-minute activity test including a two-minute baseline period and two minutes of odor exposure. Overall activity was scored during tape-playback. Odor-exposed pups were more active than non-exposed pups during reexposure to the odor during testing, but this was true only for P0 pups. In contrast, P1 pups without prior odor exposure were active during testing and behaviorally quieted in the presence of the odor they were previously exposed to. Though one day apart, newborn rats just hours old lack many of the experiences that a one day old has had including nursing, huddling, and being groomed. These experiences are associated with, among other stimuli, a barrage of olfactory cues (e.g., colostrum, saliva, dander, feces, and urine). P0 and P1 pups also differ in their proximity from the birthing experience and associated neurochemical changes. The age-related pattern of responding to odors based on previous odor exposure was discussed in relation to these and other possibilities. PMID:20411590

Mere odor exposure learning in the rat neonate immediately after birth and 1 day later.

PubMed

Miller, Stacie S; Spear, Norman E

2010-05-01

Rat pups are more resistant to retroactive associative interference 3 hr after birth than 24 hr later [Cheslock et al. [2004] Developmental Science, 7, 581-598]. The present experiments tested the effect of age, retention interval and dam presence during the retention interval on odor-induced motor activity subsequent to mere odor exposure. Rats were exposed to an hour of odor immediately after birth or approximately 1 day later and tested after a given retention interval (3 or 27 hr [Exp 1]; 0, 30, 75, or 180 min [Exp. 2]). They spent the retention interval either in the presence or absence of a foster dam (Exp. 1 and 3). After the retention interval, pups were tested in a 4-min activity test including a 2-min baseline period and 2 min of odor exposure. Overall activity was scored during tape-playback. Odor-exposed pups were more active than nonexposed pups during reexposure to the odor during testing, but this was true only for P0 pups. In contrast, P1 pups without prior odor exposure were active during testing and behaviorally quieted in the presence of the odor they were previously exposed to. Though 1 day apart, newborn rats just hours old lack many of the experiences that a 1-day-old has had including nursing, huddling, and being groomed. These experiences are associated with, among other stimuli, a barrage of olfactory cues (e.g., colostrum, saliva, dander, feces, and urine). P0 and P1 pups also differ in their proximity from the birthing experience and associated neurochemical changes. The age-related pattern of responding to odors based on previous odor exposure was discussed in relation to these and other possibilities.

[Testing the efficacy of disinfectants during drinking water treatment. A new experimental set-up at the German EPA (Umweltbundesamt - UBA)].

PubMed

Grützmacher, G; Bartel, H; Althoff, H W; Clemen, S

2007-03-01

A set-up for experiments in the flow-through mode was constructed in order to test the efficacy of substances used for disinfecting water during drinking water treatment. A flow-through mode - in contrast to experiments under stationary conditions (so-called batch experiments) - was chosen, because this experimental design allows experiments to be carried out under constant conditions for an extended time (up to one week) and because efficacy testing is possible repeatedly, simultaneously and under exactly the same conditions for short (about 0.5 min) and also longer (about 47 min) contact times. With this experimental design the effect of biofilms along the inner pipe surfaces can be included in the observations. The construction of the experimental set-up is based on experience with laboratory flow-through systems that were installed by the UBA's drinking water department (formerly Institute for Water-, Soil- and Air Hygiene (WaBoLu) Institute) for testing disinfection with chlorine. In the first step, a test pipe for the simulation of a water works situation was installed. Water of different qualities can be mixed in large volumes beforehand so that the experimental procedure can be run with constant water quality for a minimum of one week. The kinetics of the disinfection reaction can be observed by extracting samples from eight sampling ports situated along the test pipe. In order to assign exact residence times to each of the sampling ports, tracer experiments were performed prior to testing disinfectant efficacy. This paper gives the technical details of the experimental set-up and presents the results of the tracer experiments to provide an introduction with respect to its potential.

National Transonic Facility Wall Pressure Calibration Using Modern Design of Experiments (Invited)

NASA Technical Reports Server (NTRS)

Underwood, Pamela J.; Everhart, Joel L.; DeLoach, Richard

2001-01-01

The Modern Design of Experiments (MDOE) has been applied to wind tunnel testing at NASA Langley Research Center for several years. At Langley, MDOE has proven to be a useful and robust approach to aerodynamic testing that yields significant reductions in the cost and duration of experiments while still providing for the highest quality research results. This paper extends its application to include empty tunnel wall pressure calibrations. These calibrations are performed in support of wall interference corrections. This paper will present the experimental objectives, and the theoretical design process. To validate the tunnel-empty-calibration experiment design, preliminary response surface models calculated from previously acquired data are also presented. Finally, lessons learned and future wall interference applications of MDOE are discussed.

Source Term Experiments Project (STEP): Aerosol characterization system

NASA Astrophysics Data System (ADS)

Schlenger, B. J.; Dunn, P. F.

A series of four experiments is being conducted at Argonne National Laboratory's TREAT Reactor. They were designed to provide some of the necessary data regarding magnitude and release rates of fission products from degraded fuel pins, physical and chemical characteristics of released fission products, and aerosol formation and transport phenomena. These are in pile experiments, whereby the test fuel is heated by neutron induced fission and subsequent clad oxidation in steam environments that simulate as closely as practical predicted reactor accident conditions. The test sequences cover a range of pressure and fuel heatup rate, and include the effect of Aq/In/Cd control rod material.

Co-streaming classes: a follow-up study in improving the user experience to better reach users.

PubMed

Hayes, Barrie E; Handler, Lara J; Main, Lindsey R

2011-01-01

Co-streaming classes have enabled library staff to extend open classes to distance education students and other users. Student evaluations showed that the model could be improved. Two areas required attention: audio problems experienced by online participants and staff teaching methods. Staff tested equipment and adjusted software configuration to improve user experience. Staff training increased familiarity with specialized teaching techniques and troubleshooting procedures. Technology testing and staff training were completed, and best practices were developed and applied. Class evaluations indicate improvements in classroom experience. Future plans include expanding co-streaming to more classes and on-going data collection, evaluation, and improvement of classes.

Preliminary flight test results from the advanced photovoltaic experiment

NASA Technical Reports Server (NTRS)

Brinker, David J.; Hickey, John R.

1990-01-01

The Advanced Photovoltaic Experiment is a space flight test designed to provide reference cell standards for photovoltaic measurement as well as to investigate the solar spectrum and the effect of the space environment on solar cells. After a flight of 69 months in low earth orbit as part of the Long Duration Exposure Facility set of experiments, it was retrieved in January, 1990. The electronic data acquisition system functioned as designed, measuring and recording cell performance data over the first 358 days of flight, limited by battery lifetime. Significant physical changes are also readily apparent, including erosion of front surface paint, micrometeoroid and debris catering and contamination.

Preliminary results from the advanced photovoltaic experiment flight test

NASA Technical Reports Server (NTRS)

Brinker, David J.; Hart, Russell E., Jr.; Hickey, John R.

1990-01-01

The Advanced Photovoltaic Experiment is a space flight test designed to provide reference cell standards for photovoltaic measurement as well as to investigate the solar spectrum and the effect of the space environment on solar cells. After a flight of 69 months in low earth orbit as part of the Long Duration Exposure Facility set of experiments, it was retrieved in January, 1990. The electronic data acquisition system functioned as designed, measuring and recording cell performance data over the first 358 days of flight; limited by battery lifetime. Significant physical changes are also readily apparent, including erosion of front surface paint, micrometeoroid and debris catering and contamination.

Dumpster Optics: teaching and learning optics without a kit

NASA Astrophysics Data System (ADS)

Donnelly, Judy; Magnani, Nancy; Robinson, Kathleen

2016-09-01

The Next Generation Science Standards (NGSS) and renewed emphasis on STEM education in the U.S. have resulted in the development of many educational kits for teaching science in general and optics in particular. Many teachers do not have funding to purchase kits and practical experience has shown that even costly kits can have poorly written and misleading instructions and may include experiments that would not work in a classroom. Dumpster Optics lessons are designed to use inexpensive, commonly found materials. All lessons have been field-tested with students. We will describe the development of the lessons, provide examples of field testing experiences and outline possible future activities.

International testing of a Mars rover prototype

NASA Astrophysics Data System (ADS)

Kemurjian, Alexsandr Leonovich; Linkin, V.; Friedman, L.

1993-03-01

Tests on a prototype engineering model of the Russian Mars 96 Rover were conducted by an international team in and near Death Valley in the United States in late May, 1992. These tests were part of a comprehensive design and testing program initiated by the three Russian groups responsible for the rover development. The specific objectives of the May tests were: (1) evaluate rover performance over different Mars-like terrains; (2) evaluate state-of-the-art teleoperation and autonomy development for Mars rover command, control and navigation; and (3) organize an international team to contribute expertise and capability on the rover development for the flight project. The range and performance that can be planned for the Mars mission is dependent on the degree of autonomy that will be possible to implement on the mission. Current plans are for limited autonomy, with Earth-based teleoperation for the nominal navigation system. Several types of television systems are being investigated for inclusion in the navigation system including panoramic camera, stereo, and framing cameras. The tests used each of these in teleoperation experiments. Experiments were included to consider use of such TV data in autonomy algorithms. Image processing and some aspects of closed-loop control software were also tested. A micro-rover was tested to help consider the value of such a device as a payload supplement to the main rover. The concept is for the micro-rover to serve like a mobile hand, with its own sensors including a television camera.

Dynamic test results for the CASES ground experiment

NASA Technical Reports Server (NTRS)

Bukley, Angelia P.; Patterson, Alan F.; Jones, Victoria L.

1993-01-01

The Controls, Astrophysics, and Structures Experiment in Space (CASES) Ground Test Facility (GTF) has been developed at Marshall Space Flight Center (MSFC) to provide a facility for the investigation of Controls/Structures Interaction (CSI) phenomena, to support ground testing of a potential shuttle-based CASES flight experiment, and to perform limited boom deployment and retraction dynamics studies. The primary objectives of the ground experiment are to investigate CSI on a test article representative of a Large Space Structure (LSS); provide a platform for Guest Investigators (GI's) to conduct CSI studies; to test and evaluate LSS control methodologies, system identification (ID) techniques, failure mode analysis; and to compare ground test predictions and flight results. The proposed CASES flight experiment consists of a 32 meter deployable/retractable boom at the end of which is an occulting plate. The control objective of the experiment is to maintain alignment of the tip plate (occulter) with a detector located at the base of the boom in the orbiter bay. The tip plate is pointed towards a star, the sun, or the galactic center to collect high-energy X-rays emitted by these sources. The tip plate, boom, and detector comprise a Fourier telescope. The occulting holes in the tip plate are approximately one millimeter in diameter making the alignment requirements quite stringent. Control authority is provided by bidirectional linear thrusters located at the boom tip and Angular Momentum Exchange Devices (AMED's) located at mid-boom and at the tip. The experiment embodies a number of CSI control problems including vibration suppression, pointing a long flexible structure, and disturbance rejection. The CASES GTF is representative of the proposed flight experiment with identical control objectives.

Learning curves and impact of previous operative experience on performance on a virtual reality simulator to test laparoscopic surgical skills.

PubMed

Grantcharov, Teodor P; Bardram, Linda; Funch-Jensen, Peter; Rosenberg, Jacob

2003-02-01

The study was carried out to analyze the learning rate for laparoscopic skills on a virtual reality training system and to establish whether the simulator was able to differentiate between surgeons with different laparoscopic experience. Forty-one surgeons were divided into three groups according to their experience in laparoscopic surgery: masters (group 1, performed more than 100 cholecystectomies), intermediates (group 2, between 15 and 80 cholecystectomies), and beginners (group 3, fewer than 10 cholecystectomies) were included in the study. The participants were tested on the Minimally Invasive Surgical Trainer-Virtual Reality (MIST-VR) 10 consecutive times within a 1-month period. Assessment of laparoscopic skills included time, errors, and economy of hand movement, measured by the simulator. The learning curves regarding time reached plateau after the second repetition for group 1, the fifth repetition for group 2, and the seventh repetition for group 3 (Friedman's tests P <0.05). Experienced surgeons did not improve their error or economy of movement scores (Friedman's tests, P >0.2) indicating the absence of a learning curve for these parameters. Group 2 error scores reached plateau after the first repetition, and group 3 after the fifth repetition. Group 2 improved their economy of movement score up to the third repetition and group 3 up to the sixth repetition (Friedman's tests, P <0.05). Experienced surgeons (group 1) demonstrated best performance parameters, followed by group 2 and group 3 (Mann-Whitney test P <0.05). Different learning curves existed for surgeons with different laparoscopic background. The familiarization rate on the simulator was proportional to the operative experience of the surgeons. Experienced surgeons demonstrated best laparoscopic performance on the simulator, followed by those with intermediate experience and the beginners. These differences indicate that the scoring system of MIST-VR is sensitive and specific to measuring skills relevant for laparoscopic surgery.

NASA Bioculture System: From Experiment Definition to Flight Payload

NASA Technical Reports Server (NTRS)

Sato, Kevin Y.; Almeida, Eduardo; Austin, Edward M.

2014-01-01

Starting in 2015, the NASA Bioculture System will be available to the science community to conduct cell biology and microbiology experiments on ISS. The Bioculture System carries ten environmentally independent Cassettes, which house the experiments. The closed loop fluids flow path subsystem in each Cassette provides a perfusion-based method for maintain specimen cultures in a shear-free environment by using a biochamber based on porous hollow fiber bioreactor technology. Each Cassette contains an incubator and separate insulated refrigerator compartment for storage of media, samples, nutrients and additives. The hardware is capable of fully automated or manual specimen culturing and processing, including in-flight experiment initiation, sampling and fixation, up to BSL-2 specimen culturing, and the ability to up to 10 independent cultures in parallel for statistical analysis. The incubation and culturing of specimens in the Bioculture System is a departure from standard laboratory culturing methods. Therefore, it is critical that the PI has an understanding the pre-flight test required for successfully using the Bioculture System to conduct an on-orbit experiment. Overall, the PI will conduct a series of ground tests to define flight experiment and on-orbit implementation requirements, verify biocompatibility, and determine base bioreactor conditions. The ground test processes for the utilization of the Bioculture System, from experiment selection to flight, will be reviewed. Also, pre-flight test schedules and use of COTS ground test equipment (CellMax and FiberCell systems) and the Bioculture System will be discussed.

AgRISTARS: Foreign commodity production forecasting. Minutes of the annual formal project manager's review, including preliminary technical review reports of FY80 experiments. [wheat/barley and corn/soybean experiments

NASA Technical Reports Server (NTRS)

1980-01-01

The U.S./Canada wheat/barley exploratory experiment is discussed with emphasis on labeling, machine processing using P1A, and the crop calendar. Classification and the simulated aggregation test used in the U.S. corn/soybean exploratory experiment are also considered. Topics covered regarding the foreign commodity production forecasting project include: (1) the acquisition, handling, and processing of both U.S. and foreign agricultural data, as well as meteorological data. The accuracy assessment methodology, multicrop sampling and aggregation technology development, frame development, the yield project interface, and classification for area estimation are also examined.

Analysis and Ground Testing for Validation of the Inflatable Sunshield in Space (ISIS) Experiment

NASA Technical Reports Server (NTRS)

Lienard, Sebastien; Johnston, John; Adams, Mike; Stanley, Diane; Alfano, Jean-Pierre; Romanacci, Paolo

2000-01-01

The Next Generation Space Telescope (NGST) design requires a large sunshield to protect the large aperture mirror and instrument module from constant solar exposure at its L2 orbit. The structural dynamics of the sunshield must be modeled in order to predict disturbances to the observatory attitude control system and gauge effects on the line of site jitter. Models of large, non-linear membrane systems are not well understood and have not been successfully demonstrated. To answer questions about sunshield dynamic behavior and demonstrate controlled deployment, the NGST project is flying a Pathfinder experiment, the Inflatable Sunshield in Space (ISIS). This paper discusses in detail the modeling and ground-testing efforts performed at the Goddard Space Flight Center to: validate analytical tools for characterizing the dynamic behavior of the deployed sunshield, qualify the experiment for the Space Shuttle, and verify the functionality of the system. Included in the discussion will be test parameters, test setups, problems encountered, and test results.

A comparative study of working memory: immediate serial spatial recall in baboons (Papio papio) and humans.

PubMed

Fagot, Joël; De Lillo, Carlo

2011-12-01

Two experiments assessed if non-human primates can be meaningfully compared to humans in a non-verbal test of serial recall. A procedure was used that was derived from variations of the Corsi test, designed to test the effects of sequence structure and movement path length in humans. Two baboons were tested in Experiment 1. The monkeys showed several attributes of human serial recall. These included an easier recall of sequences with a shorter number of items and of sequences characterized by a shorter path length when the number of items was kept constant. However, the accuracy and speed of processing did not indicate that the monkeys were able to benefit from the spatiotemporal structure of sequences. Humans tested in Experiment 2 showed a quantitatively longer memory span, and, in contrast with monkeys, benefitted from sequence structure. The results are discussed in relation to differences in how human and non-human primates segment complex visual patterns. Copyright © 2011 Elsevier Ltd. All rights reserved.

HIV testing and counseling: test providers' experiences of best practices.

PubMed

Myers, Ted; Worthington, Catherine; Haubrich, Dennis J; Ryder, Karen; Calzavara, Liviana

2003-08-01

Although education is central to HIV testing and counseling, little is known about the educational processes within the testing experience. This study investigated test providers' understandings of testing and counseling best practices. Interviews with a purposive sample of 24 test providers were thematically analyzed. Analysis revealed five best practices specific to HIV education and public health--ensuring information and education for HIV risk reduction, individualization of risk assessment, ensuring test results are given in person, providing information and referrals, and facilitating partner notification--and six practices not specific to HIV counseling relationship building. The latter were building trust and rapport; maintaining professional boundaries; ensuring a comfortable, safe environment; ensuring confidentiality; imparting nonjudgmntal attitude; and self-determination. The identified best practices demonstrated remarkable consistency across respondent subgroups. Although counseling was seen as largely educational and with a preventive focus, it included individualized messages based on assessments of risk, knowledge, and social and cultural characteristics.

International Space Station (ISS)

NASA Image and Video Library

2003-01-16

In this International Space Station (ISS) onboard photo, Expedition Six Science Officer Donald R. Pettit works to set up the Pulmonary Function in Flight (PuFF) experiment hardware in the Destiny Laboratory. Expedition Six is the fourth and final crew to perform the PuFF experiment. The PuFF experiment was developed to better understand what effects long term exposure to microgravity may have on the lungs. The focus is on measuring changes in the everness of gas exchange in the lungs, and on detecting changes in respiratory muscle strength. It allows astronauts to measure blood flow through the lungs, the ability of the lung to take up oxygen, and lung volumes. Each PuFF session includes five lung function tests, which involve breathing only cabin air. For each planned extravehicular (EVA) activity, a crew member performs a PuFF test within one week prior to the EVA. Following the EVA, those crew members perform another test to document the effect of exposure of the lungs to the low-pressure environment of the space suits. This experiment utilizes the Gas Analyzer System for Metabolic Analysis Physiology, or GASMAP, located in the Human Research Facility (HRF), along with a variety of other Puff equipment including a manual breathing valve, flow meter, pressure-flow module, pressure and volume calibration syringes, and disposable mouth pieces.

Bullet Impact Safety Study of PBX-9502

NASA Astrophysics Data System (ADS)

Ferranti, Louis

2013-06-01

A new small arms capability for performing bullet impact testing into energetic materials has recently been activated at Lawrence Livermore National Laboratory located in the High Explosives Applications Facility (HEAF). The initial capability includes 0.223, 0.30, and 0.50 testing calibers with the flexibility to add other barrels in the near future. An initial test series has been performed using the 0.50 caliber barrel shooting bullets into targets using the TATB based explosive PBX-9502 and shows an expected non-violent reaction. Future experiments to evaluate the safety of new explosive formulations to bullet impact are planned. A highlight of the new capability along with discussion of the initial experiments to date will be presented including future areas of research. This work performed under the auspices of the U.S. Department of Energy by Lawrence Livermore National Laboratory under Contract DE-AC52-07NA27344.

STS-47 Mission Highlights Resource Tape

NASA Technical Reports Server (NTRS)

1992-01-01

The mission of the STS-47 flight is highlighted in this video. The flight crew consisted of: Cmdr. 'Hoot' Gibson, Pilot Kurt Brown, Payload Cmdr. Jan Davis, Payload Specialist. M. Mohri (Japanese Astronaut), and Mission Specialists Jay Apt and May Jemison. The primary goal of this mission was the set-up and carrying out of experiments in the accompanying Japanese Spacelab (SL-J) in cooperation with the Japanese Space Program. Dr. Mohri is the first professional Japanese astronaut to fly in space. Vice President Dan Quayle and his wife are shown addressing the astronauts of the Space Shuttle Endeavour with a small pre-launch speech. On this flight many different physical, physiological, and biological spaceborne experiments were performed. These experiments included: a gas evaporation in low gravity environment experiment; a brainwave signals from carp experiment; several human eye movement and visual physiological tests; various physiological tests on a variety of insects and frogs; a embryology experiments on tadpoles; several experiments concerned with fluid dynamics; an imaging furnace test with heated glass containing gold particles (flow measurement); a Solid Surface Combustion Experiment; and a protein crystal growth experiment. Launch, in-orbit, and landing footage is shown, along with a variety of crew activities. One feature that astronauts were able to videotape was the actual in-orbit movement of the side wing flaps of the Space Shuttle.

STS-75 Flight Day 10

NASA Technical Reports Server (NTRS)

1996-01-01

On this tenth day of the STS-75 mission, the flight crew, Cmdr. Andrew Allen, Pilot Scott Horowitz, Payload Cmdr. Franklin Chang-Diaz, Payload Specialist Umberto Guidoni (Italy), and Missions Specialists Jeffrey Hoffman, Maurizio Cheli (ESA), and Claude Nicollier (ESA), are shown performing middeck and Microgravity lab experiments, including the Material pour l'Etude des Phenomenes Interessant la Solidification sur Terre et en Orbite (MEPHISTO) experiment, as well as some material burn tests. Earth views include cloud cover and horizon shots.

Life in the Atacama - Year 2: Geologic Reconnaissance Through Long-Range Roving and Implications on the Search for Life

NASA Technical Reports Server (NTRS)

Dohm, J. M.; Cabrol, N. A.; Grin, E. A.; Moersch, J.; Diaz, G. Chong; Cockell, C.; Coppin, P.; Fisher, G.; Hock, A. N.; Ori, G. G.

2005-01-01

The "Life in the Atacama" (LITA) project included two field trials during the 2004 field season, each of which lasted about a week. The remote science team had no prior knowledge of the local geology, and relied entirely on orbital images and rover-acquired data to make interpretations. The sites for these trials were in different locations, and are designated "Site B" and "Site C" respectively. The primary objective of the experiment is to develop and test the means to locate, characterize, and identify habitats and life remotely through long-range roving, which included field testing the rover, named Zoe. Zoe has onboard autonomous navigation for long-range roving, a plow to overturn rocks and expose near-surface rock materials, and high-resolution imaging, spectral, and fluorescence sampling capabilities. Highlights from the experiment included characterizing the geology in and near the landing ellipse, assessing pre-mission, satellite-based hypotheses, and improving the approach and procedures used by the remote and field teams for upcoming experiments through combined satellite, field-based, and microscopic perspectives and long-range roving.

The Penefit of Salience: Salient Accented, but Not Unaccented Words Reveal Accent Adaptation Effects.

PubMed

Grohe, Ann-Kathrin; Weber, Andrea

2016-01-01

In two eye-tracking experiments, the effects of salience in accent training and speech accentedness on spoken-word recognition were investigated. Salience was expected to increase a stimulus' prominence and therefore promote learning. A training-test paradigm was used on native German participants utilizing an artificial German accent. Salience was elicited by two different criteria: production and listening training as a subjective criterion and accented (Experiment 1) and canonical test words (Experiment 2) as an objective criterion. During training in Experiment 1, participants either read single German words out loud and deliberately devoiced initial voiced stop consonants (e.g., Balken-"beam" pronounced as (*) Palken), or they listened to pre-recorded words with the same accent. In a subsequent eye-tracking experiment, looks to auditorily presented target words with the accent were analyzed. Participants from both training conditions fixated accented target words more often than a control group without training. Training was identical in Experiment 2, but during test, canonical German words that overlapped in onset with the accented words from training were presented as target words (e.g., Palme-"palm tree" overlapped in onset with the training word (*) Palken) rather than accented words. This time, no training effect was observed; recognition of canonical word forms was not affected by having learned the accent. Therefore, accent learning was only visible when the accented test tokens in Experiment 1, which were not included in the test of Experiment 2, possessed sufficient salience based on the objective criterion "accent." These effects were not modified by the subjective criterion of salience from the training modality.

Parameter estimation techniques and application in aircraft flight testing

NASA Technical Reports Server (NTRS)

1974-01-01

Technical papers presented at the symposium by selected representatives from industry, universities, and various Air Force, Navy, and NASA installations are given. The topics covered include the newest developments in identification techniques, the most recent flight-test experience, and the projected potential for the near future.

Evaluation of functional color vision requirements and current color vision screening tests for air traffic control specialists.

DOT National Transportation Integrated Search

1990-08-01

An experiment was conducted to evaluate the relation of type and degree of color vision deficiency and aeromedical color vision screening test scores to performance of color-dependent tasks of Air Traffic Control Specialists. The subjects included 37...

Experience with code-switching modulates the use of grammatical gender during sentence processing

PubMed Central

Valdés Kroff, Jorge R.; Dussias, Paola E.; Gerfen, Chip; Perrotti, Lauren; Bajo, M. Teresa

2016-01-01

Using code-switching as a tool to illustrate how language experience modulates comprehension, the visual world paradigm was employed to examine the extent to which gender-marked Spanish determiners facilitate upcoming target nouns in a group of Spanish-English bilingual code-switchers. The first experiment tested target Spanish nouns embedded in a carrier phrase (Experiment 1b) and included a control Spanish monolingual group (Experiment 1a). The second set of experiments included critical trials in which participants heard code-switches from Spanish determiners into English nouns (e.g., la house) either in a fixed carrier phrase (Experiment 2a) or in variable and complex sentences (Experiment 2b). Across the experiments, bilinguals revealed an asymmetric gender effect in processing, showing facilitation only for feminine target items. These results reflect the asymmetric use of gender in the production of code-switched speech. The extension of the asymmetric effect into Spanish (Experiment 1b) underscores the permeability between language modes in bilingual code-switchers. PMID:28663771

Solar array module plasma interactions experiment (SAMPIE) - Science and technology objectives

NASA Technical Reports Server (NTRS)

Hillard, G. B.; Ferguson, Dale C.

1993-01-01

The solar array module plasma interactions experiment (SAMPIE) is an approved NASA flight experiment manifested for Shuttle deployment in early 1994. The SAMPIE experiment is designed to investigate the interaction of high voltage space power systems with ionospheric plasma. To study the behavior of solar cells, a number of solar cell coupons (representing design technologies of current interest) will be biased to high voltages to measure both arcing and current collection. Various theories of arc suppression will be tested by including several specially modified cell coupons. Finally, SAMPIE will include experiments to study the basic nature of arcing and current collection. This paper describes the rationale for a space flight experiment, the measurements to be made, and the significance of the expected results. A future paper will present a detailed discussion of the engineering design.

Assessing Boundary Conditions of the Testing Effect: On the Relative Efficacy of Covert vs. Overt Retrieval

PubMed Central

Sundqvist, Max L.; Mäntylä, Timo; Jönsson, Fredrik U.

2017-01-01

Repeated testing during learning often improves later memory, which is often referred to as the testing effect. To clarify its boundary conditions, we examined whether the testing effect was selectively affected by covert (retrieved but not articulated) or overt (retrieved and articulated) response format. In Experiments 1 and 2, we compared immediate (5 min) and delayed (1 week) cued recall for paired associates following study-only, covert, and overt conditions, including two types of overt articulation (typing and writing). A clear testing effect was observed in both experiments, but with no selective effects of response format. In Experiments 3 and 4, we compared covert and overt retrieval under blocked and random list orders. The effect sizes were small in both experiments, but there was a significant effect of response format, with overt retrieval showing better final recall performance than covert retrieval. There were no significant effects of blocked vs. random list orders with respect to the testing effect produced. Taken together, these findings suggest that, under specific circumstances, overt retrieval may lead to a greater testing effect than that of covert retrieval, but because of small effect sizes, it appears that the testing effect is mainly the result of retrieval processes and that articulation has fairly little to add to its magnitude in a paired-associates learning paradigm. PMID:28680411

Assessing Boundary Conditions of the Testing Effect: On the Relative Efficacy of Covert vs. Overt Retrieval.

PubMed

Sundqvist, Max L; Mäntylä, Timo; Jönsson, Fredrik U

2017-01-01

Repeated testing during learning often improves later memory, which is often referred to as the testing effect. To clarify its boundary conditions, we examined whether the testing effect was selectively affected by covert (retrieved but not articulated) or overt (retrieved and articulated) response format. In Experiments 1 and 2, we compared immediate (5 min) and delayed (1 week) cued recall for paired associates following study-only, covert, and overt conditions, including two types of overt articulation (typing and writing). A clear testing effect was observed in both experiments, but with no selective effects of response format. In Experiments 3 and 4, we compared covert and overt retrieval under blocked and random list orders. The effect sizes were small in both experiments, but there was a significant effect of response format, with overt retrieval showing better final recall performance than covert retrieval. There were no significant effects of blocked vs. random list orders with respect to the testing effect produced. Taken together, these findings suggest that, under specific circumstances, overt retrieval may lead to a greater testing effect than that of covert retrieval, but because of small effect sizes, it appears that the testing effect is mainly the result of retrieval processes and that articulation has fairly little to add to its magnitude in a paired-associates learning paradigm.

Mechanical Testing of Silicon Carbide on MISSE-7

DTIC Science & Technology

2012-07-15

JS) ii Abstract Silicon carbide ( SiC ) mechanical test specimens were included on the second Optical and Reflector Materials Experiment (ORMatE II...2. Vendor 2 EFS Weibull Results (normalized to Extra Disks Weibull parameters) 12 1. Introduction Silicon carbide ( SiC ) mechanical test...AEROSPACE REPORT NO ATR-2012(8921)-5 Mechanical Testing of Silicon Carbide on MISSE-7 Jul> 15. 2012 David B. Witkin Space Materials Laboratory

A proposed protocol for acceptance and constancy control of computed tomography systems: a Nordic Association for Clinical Physics (NACP) work group report.

PubMed

Kuttner, Samuel; Bujila, Robert; Kortesniemi, Mika; Andersson, Henrik; Kull, Love; Østerås, Bjørn Helge; Thygesen, Jesper; Tarp, Ivanka Sojat

2013-03-01

Quality assurance (QA) of computed tomography (CT) systems is one of the routine tasks for medical physicists in the Nordic countries. However, standardized QA protocols do not yet exist and the QA methods, as well as the applied tolerance levels, vary in scope and extent at different hospitals. To propose a standardized protocol for acceptance and constancy testing of CT scanners in the Nordic Region. Following a Nordic Association for Clinical Physics (NACP) initiative, a group of medical physicists, with representatives from four Nordic countries, was formed. Based on international literature and practical experience within the group, a comprehensive standardized test protocol was developed. The proposed protocol includes tests related to the mechanical functionality, X-ray tube, detector, and image quality for CT scanners. For each test, recommendations regarding the purpose, equipment needed, an outline of the test method, the measured parameter, tolerance levels, and the testing frequency are stated. In addition, a number of optional tests are briefly discussed that may provide further information about the CT system. Based on international references and medical physicists' practical experiences, a comprehensive QA protocol for CT systems is proposed, including both acceptance and constancy tests. The protocol may serve as a reference for medical physicists in the Nordic countries.

Surface gloss and color perception of 3D objects.

PubMed

Xiao, Bei; Brainard, David H

2008-01-01

Two experiments explore the color perception of objects in complex scenes. The first experiment examines the color perception of objects across variation in surface gloss. Observers adjusted the color appearance of a matte sphere to match that of a test sphere. Across conditions we varied the body color and glossiness of the test sphere. The data indicate that observers do not simply match the average light reflected from the test. Indeed, the visual system compensates for the physical effect of varying the gloss, so that appearance is stabilized relative to what is predicted by the spatial average. The second experiment examines how people perceive color across locations on an object. We replaced the test sphere with a soccer ball that had one of its hexagonal faces colored. Observers were asked to adjust the match sphere have the same color appearance as this test patch. The test patch could be located at either an upper or lower location on the soccer ball. In addition, we varied the surface gloss of the entire soccer ball (including the test patch). The data show that there is an effect of test patch location on observers' color matching, but this effect is small compared to the physical change in the average light reflected from the test patch across the two locations. In addition, the effect of glossy highlights on the color appearance of the test patch was consistent with the results from Experiment 1.

Surface gloss and color perception of 3D objects

PubMed Central

Xiao, Bei; Brainard, David H.

2008-01-01

Two experiments explore the color perception of objects in complex scenes. The first experiment examines the color perception of objects across variation in surface gloss. Observers adjusted the color appearance of a matte sphere to match that of a test sphere. Across conditions we varied the body color and glossiness of the test sphere. The data indicate that observers do not simply match the average light reflected from the test. Indeed, the visual system compensates for the physical effect of varying the gloss, so that appearance is stabilized relative to what is predicted by the spatial average. The second experiment examines how people perceive color across locations on an object. We replaced the test sphere with a soccer ball that had one of its hexagonal faces colored. Observers were asked to adjust the match sphere have the same color appearance as this test patch. The test patch could be located at either an upper or lower location on the soccer ball. In addition, we varied the surface gloss of the entire soccer ball (including the test patch). The data show that there is an effect of test patch location on observers’ color matching, but this effect is small compared to the physical change in the average light reflected from the test patch across the two locations. In addition, the effect of glossy highlights on the color appearance of the test patch was consistent with the results from Experiment 1. PMID:18598406

TREAT Neutronics Analysis and Design Support, Part II: Multi-SERTTA-CAL

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bess, John D.; Woolstenhulme, Nicolas E.; Hill, Connie M.

2016-08-01

Experiment vehicle design is necessary in preparation for Transient Reactor Test (TREAT) facility restart and the resumption of transient testing to support Accident Tolerant Fuel (ATF) characterization and other future fuels testing requirements. Currently the most mature vehicle design is the Multi-SERTTA (Static Environments Rodlet Transient Test Apparatuses), which can accommodate up to four concurrent rodlet-sized specimens under separate environmental conditions. Robust test vehicle design requires neutronics analyses to support design development, optimization of the power coupling factor (PCF) to efficiently maximize energy generation in the test fuel rodlets, and experiment safety analyses. In integral aspect of prior TREAT transientmore » testing was the incorporation of calibration experiments to experimentally evaluate and validate test conditions in preparation of the actual fuel testing. The calibration experiment package established the test parameter conditions to support fine-tuning of the computational models to deliver the required energy deposition to the fuel samples. The calibration vehicle was designed to be as near neutronically equivalent to the experiment vehicle as possible to minimize errors between the calibration and final tests. The Multi-SERTTA-CAL vehicle was designed to serve as the calibration vehicle supporting Multi-SERTTA experimentation. Models of the Multi-SERTTA-CAL vehicle containing typical PWR-fuel rodlets were prepared and neutronics calculations were performed using MCNP6.1 with ENDF/B-VII.1 nuclear data libraries; these results were then compared against those performed for Multi-SERTTA to determine the similarity and possible design modification necessary prior to construction of these experiment vehicles. The estimated reactivity insertion worth into the TREAT core is very similar between the two vehicle designs, with the primary physical difference being a hollow Inconel tube running down the length of the calibration vehicle. Calculations of PCF indicate that on average there is a reduction of approximately 6.3 and 12.6%, respectively, for PWR fuel rodlets irradiated under wet and dry conditions. Changes to the primary or secondary vessel structure in the calibration vehicle can be performed to offset this discrepancy and maintain neutronic equivalency. Current possible modifications to the calibration vehicle include reduction of the primary vessel wall thickness, swapping Zircaloy-4 for stainless steel 316 in the secondary containment, or slight modification to the temperature and pressure of the water environment within the primary vessel. Removal of some of the instrumentation within the calibration vehicle can also serve to slightly increase the PCF. Future efforts include further modification and optimization of the Multi-SERTTA and Multi-SERTTA-CAL designs in preparation of actual TREAT transient testing. Experimental results from both test vehicles will be compared against calculational results and methods to provide validation and support additional neutronics analyses.« less

Robotic joint experiments under ultravacuum

NASA Technical Reports Server (NTRS)

Borrien, A.; Petitjean, L.

1988-01-01

First, various aspects of a robotic joint development program, including gearbox technology, electromechanical components, lubrication, and test results, are discussed. Secondly, a test prototype of the joint allowing simulation of robotic arm dynamic effects is presented. This prototype is tested under vacuum with different types of motors and sensors to characterize the functional parameters: angular position error, mechanical backlash, gearbox efficiency, and lifetime.

The teratology testing of cosmetics.

PubMed

Spézia, François; Barrow, Paul C

2013-01-01

In Europe, the developmental toxicity testing (including teratogenicity) of new cosmetic ingredients is performed according to the Cosmetics Directive 76/768/EEC: only alternatives leading to full replacement of animal experiments should be used. This chapter presents the three scientifically validated animal alternative methods for the assessment of embryotoxicity: the embryonic stem cell test (EST), the micromass (MM) assay, and the whole embryo culture (WEC) assay.

Adolescent Girls' Preferences Pertaining to Cardiovascular Fitness Testing: A Comparison between the One-Mile Run and PACER Tests

ERIC Educational Resources Information Center

Wilkinson, Carol; Brown, Lanell; Graser, Sue Vincent; Pennington, Todd R.

2012-01-01

Many adolescent girls are not participating in the recommended levels of physical activity (PA) and are at risk for unhealthy lifestyles (U.S. Department of Health and Human Services, 2008). Helping girls understand the importance of PA and giving them positive experiences in physical education classes, including fitness testing, may help to…

An Advanced Pharmacy Practice Experience in Sports Pharmacy

PubMed Central

2008-01-01

Objective To establish and evaluate an advanced pharmacy practice experience (APPE) in sports pharmacy. Design Students actively participated in a variety of activities for this new 6-week elective APPE, including drug-testing collections, delivering presentations, and providing drug information. Students also learned about assays, compounding, and dispensing medications specifically for athletes, and visited various athletic medical facilities. Student were given written and practical certification examinations for drug-testing collections, and their specimen measurements were compared to those obtained by the testing laboratory for validation; satisfaction surveys were obtained from testing sites; and presentation evaluations were obtained from audience participants. Assessment Students were able to accurately measure pH and specific gravity of urine samples and all students passed the certification examination. Students rated the APPE very high. Also, students received high satisfaction ratings on surveys administered to the officials of the schools where they tested and members of the groups to whom they gave presentations. Conclusion Students gained experience and insight into the various roles of pharmacists in sports pharmacy and developed confidence in their ability to conduct drug-testing collections. PMID:18322580

Investigating the impact of innate dexterity skills and visuospatial aptitude on the performance of baseline laparoscopic skills in veterinary students.

PubMed

MacCormick, Mathew R A; Kilkenny, Jessica J; Walker, Meagan; Zur Linden, Alex; Singh, Ameet

2017-11-01

To determine if manual dexterity and visuospatial skills can be used to predict baseline laparoscopic surgery skills in veterinary students. Pilot study. Veterinary students (n = 45) from years 1-4 volunteered for this study. An hour-long electronic questionnaire was completed by participants. The first section was used to collect demographics and information about prior nonsurgical experiences. The second section included 3 tests of visuospatial skills, including the Purdue Visualization of Rotations Test, Mental Rotations Test, and Raven's Advanced Progressive Matrices Test. Multiple tests were administered to assess innate dexterity, including the grooved pegboard test, indirect and direct zigzag tracking tests, and the 3Dconnexion proficiency test. Each dexterity test was performed once with the left hand and once with the right hand. The order of task performance was randomized. Basic laparoscopic skills were assessed using the validated fundamentals of laparoscopic surgery (FLS) peg transfer task. There was an association between left-handed grooved pegboard scores (95% CI -10046.36 to -1636.53, P-value = .008) and left-handed indirect zigzag tracking task (95% CI -35.78 to -8.20, P-value = .003) with FLS peg transfer scores. Individuals who reported playing videogames achieved higher scores on the FLS peg transfer task than those without videogame experience (95% CI 583.59 to 3509.97, P-value = .007). The results of this study suggest that dexterity was a better predictor of baseline laparoscopic skills than visuospatial skills in veterinary students. © 2017 The American College of Veterinary Surgeons.

A life sciences Spacelab mission simulation

NASA Technical Reports Server (NTRS)

Mason, J. A.; Musgrave, F. S.; Morrison, D. R.

1977-01-01

The paper describes the purposes of a seven-day simulated life-sciences mission conducted in a Spacelab simulator. A major objective was the evaluation of in-orbit Spacelab operations and those mission control support functions which will be required from the Payload Operations Center. Tested equipment and procedures included experiment racks, common operational research equipment, commercial off-the-shelf equipment, experiment hardware interfaces with Spacelab, experiment data handling concepts, and Spacelab trash management.

A survey of experiments and experimental facilities for control of flexible structures

NASA Technical Reports Server (NTRS)

Sparks, Dean W., Jr.; Juang, Jer-Nan; Klose, Gerhard J.

1989-01-01

This paper presents a survey of U.S. ground experiments and facilities dedicated to the study of active control of flexible structures. The facilities will be briefly described in terms of capability, configuration, size and instrumentation. Topics on the experiments include vibration suppression, slewing and system identification. Future research directions, particularly of the NASA Langley Research Center's Controls/Structures Interaction (CSI) ground test program, will be discussed.

Wave-Sediment Interaction in Muddy Environments: A Field Experiment

DTIC Science & Technology

2008-01-01

project includes a field experiment on the Atchafalaya shelf, Louisiana, in Years 1 and 2 (2007-2008) and a data analysis and modeling effort in Year 3...2008), in collaboration with other researchers funded by ONR CG program. The pilot experiment has tested the instrumentation and data analysis ...1993; Foda et al., 1993). With the exception of liquefaction processes, these models assume a single, well­ defined mud phase. However

Design, construction, and testing of the direct absorption receiver panel research experiment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chavez, J.M.; Rush, E.E.; Matthews, C.W.

1990-01-01

A panel research experiment (PRE) was designed, built, and tested as a scaled-down model of a direct absorption receiver (DAR). The PRE is a 3-MW{sub t}DAR experiment that will allow flow testing with molten nitrate salt and provide a test bed for DAR testing with actual solar heating. In a solar central receiver system DAR, the heat absorbing fluid (a blackened molten nitrate salt) flows in a thin film down a vertical panel (rather than through tubes as in conventional receiver designs) and absorbs the concentrated solar flux directly. The ability of the flowing salt film to absorb flux directly.more » The ability of the flowing salt film to absorb the incident solar flux depends on the panel design, hydraulic and thermal fluid flow characteristics, and fluid blackener properties. Testing of the PRE is being conducted to demonstrate the engineering feasibility of the DAR concept. The DAR concept is being investigated because it offers numerous potential performance and economic advantages for production of electricity when compared to other solar receiver designs. The PRE utilized a 1-m wide by 6-m long absorber panel. The salt flow tests are being used to investigate component performance, panel deformations, and fluid stability. Salt flow testing has demonstrated that all the DAR components work as designed and that there are fluid stability issues that need to be addressed. Future solar testing will include steady-state and transient experiments, thermal loss measurements, responses to severe flux and temperature gradients and determination of peak flux capability, and optimized operation. In this paper, we describe the design, construction, and some preliminary flow test results of the Panel Research Experiment. 11 refs., 8 figs., 2 tabs.« less

Atmospheric Turbulence Statistics from GOLD Experiments

NASA Technical Reports Server (NTRS)

Jeganathan, Muthu; Wilson, Keith; Lesh, Jim

1996-01-01

Ground-Orbiter Lasercomm Demonstration (GOLD) includes the following: (1) Optical communication experiments between Table Mountain Observatory (TMF) and Japanese Engineering Test Satellite (ETS-VI); (2) International cooperative effort between NASA, NASDA, CRL and JPL; and (3) Phase 1 transmissions from October 1995 to January 1996 and Phase 2 transmissions from March 1996 to May 1996.

New Telecommunication Uses in Tama, New Town. Summary.

ERIC Educational Resources Information Center

Komatsuzaki, Seisuke

This paper deals with a Test Information Service which is being tried out in Tama, Japan. The large scale field experiment of the new telecommunication system is called Coaxial Cable Information Service (CCIS) and was started in 1976. Preliminary findings included that: 1) users are interested in the experiment; 2) two-way communication systems…

The Effects of Game Design on Learning Outcomes

ERIC Educational Resources Information Center

Martin, Michael W.; Shen, Yuzhong

2014-01-01

This article details the administration and results of an experiment conducted to assess the impact of three video game design concepts upon learning outcomes. The principles tested include game aesthetics, player choice, and player competition. The experiment participants were asked to play a serious game over the course of a week, and the…

NASA Cold Land Processes Experiment (CLPX 2002/03): Airborne remote sensing

Treesearch

Don Cline; Simon Yueh; Bruce Chapman; Boba Stankov; Al Gasiewski; Dallas Masters; Kelly Elder; Richard Kelly; Thomas H. Painter; Steve Miller; Steve Katzberg; Larry Mahrt

2009-01-01

This paper describes the airborne data collected during the 2002 and 2003 Cold Land Processes Experiment (CLPX). These data include gamma radiation observations, multi- and hyperspectral optical imaging, optical altimetry, and passive and active microwave observations of the test areas. The gamma observations were collected with the NOAA/National Weather Service Gamma...

Field testing existence values for riparian ecosystems

Treesearch

John W. Duffield; Chris J. Neher; David A. Patterson; Patricia A. Champ

2007-01-01

This paper presents preliminary findings on a cash and contingent valuation (cv) experiment. The study replicates major elements of an earlier (1990) experiment, which solicited hypothetical and actual donations to benefit instream flows for Montana fisheries. Extensions of the earlier work include: repeat contacts to increase response rate, follow-up of the contingent...

Mountain Plains Learning Experience Guide: Automotive Repair. Course: Emission Systems.

ERIC Educational Resources Information Center

Schramm, C.; Osland, Walt

One of twelve individualized courses included in an automotive repair curriculum, this course covers the theory, testing, and servicing of automotive emission control systems. The course is comprised of one unit, Fundamentals of Emission Systems. The unit begins with a Unit Learning Experience Guide that gives directions for unit completion. The…

NASA Astronauts on Soyuz: Experience and Lessons for the Future

NASA Technical Reports Server (NTRS)

2010-01-01

The U. S., Russia, and, China have each addressed the question of human-rating spacecraft. NASA's operational experience with human-rating primarily resides with Mercury, Gemini, Apollo, Space Shuttle, and International Space Station. NASA s latest developmental experience includes Constellation, X38, X33, and the Orbital Space Plane. If domestic commercial crew vehicles are used to transport astronauts to and from space, Soyuz is another example of methods that could be used to human-rate a spacecraft and to work with commercial spacecraft providers. For Soyuz, NASA's normal assurance practices were adapted. Building on NASA's Soyuz experience, this report contends all past, present, and future vehicles rely on a range of methods and techniques for human-rating assurance, the components of which include: requirements, conceptual development, prototype evaluations, configuration management, formal development reviews (safety, design, operations), component/system ground-testing, integrated flight tests, independent assessments, and launch readiness reviews. When constraints (cost, schedule, international) limit the depth/breadth of one or more preferred assurance means, ways are found to bolster the remaining areas. This report provides information exemplifying the above safety assurance model for consideration with commercial or foreign-government-designed spacecraft. Topics addressed include: U.S./Soviet-Russian government/agency agreements and engineering/safety assessments performed with lessons learned in historic U.S./Russian joint space ventures

Radon Measurement in Schools: Self-Paced Training Workbook.

ERIC Educational Resources Information Center

Institute for Disability Research and Training, Inc., Silver Spring, MD.

This workbook is designed to educate school personnel in randon detection. The workbook is intended for an audience of school officials, including administrators, business officers, facility managers, and maintenance and operations staff. It is meant to provide trainees with experience in planning a radon test, interpreting test results,…

Apollo-Soyuz test project

NASA Technical Reports Server (NTRS)

1975-01-01

Experiments proposed for the Apollo-Soyuz space mission are discussed. Data focus of space processing and manufacturing, earth surveys, and life sciences. Special efforts were made to test the compatibility of the rendezvous and docking systems for manned spacecraft. Mission planning programs, personnel training, and spacecraft modifications for both spacecraft are included.

My Pet Rock

ERIC Educational Resources Information Center

Lark, Adam; Kramp, Robyne; Nurnberger-Haag, Julie

2008-01-01

Many teachers and students have experienced the classic pet rock experiment in conjunction with a geology unit. A teacher has students bring in a "pet" rock found outside of school, and the students run geologic tests on the rock. The tests include determining relative hardness using Mohs scale, checking for magnetization, and assessing luster.…

A New Look at Bias in Aptitude Tests.

ERIC Educational Resources Information Center

Scheuneman, Janice Dowd

1981-01-01

Statistical bias in measurement and ethnic-group bias in testing are discussed, reviewing predictive and construct validity studies. Item bias is reconceptualized to include distance of item content from respondent's experience. Differing values of mean and standard deviation for bias parameter are analyzed in a simulation. References are…

Project Physics Tests 5, Models of the Atom.

ERIC Educational Resources Information Center

Harvard Univ., Cambridge, MA. Harvard Project Physics.

Test items relating to Project Physics Unit 5 are presented in this booklet. Included are 70 multiple-choice and 23 problem-and-essay questions. Concepts of atomic model are examined on aspects of relativistic corrections, electron emission, photoelectric effects, Compton effect, quantum theories, electrolysis experiments, atomic number and mass,…

Testing the Fracture Behaviour of Chocolate

ERIC Educational Resources Information Center

Parsons, L. B.; Goodall, R.

2011-01-01

In teaching the materials science aspects of physics, mechanical behaviour is important due to its relevance to many practical applications. This article presents a method for experimentally examining the toughness of chocolate, including a design for a simple test rig, and a number of experiments that can be performed in the classroom. Typical…

Upscaling of U (VI) desorption and transport from decimeter‐scale heterogeneity to plume‐scale modeling

USGS Publications Warehouse

Curtis, Gary P.; Kohler, Matthias; Kannappan, Ramakrishnan; Briggs, Martin A.; Day-Lewis, Frederick D.

2015-01-01

Scientifically defensible predictions of field scale U(VI) transport in groundwater requires an understanding of key processes at multiple scales. These scales range from smaller than the sediment grain scale (less than 10 μm) to as large as the field scale which can extend over several kilometers. The key processes that need to be considered include both geochemical reactions in solution and at sediment surfaces as well as physical transport processes including advection, dispersion, and pore-scale diffusion. The research summarized in this report includes both experimental and modeling results in batch, column and tracer tests. The objectives of this research were to: (1) quantify the rates of U(VI) desorption from sediments acquired from a uranium contaminated aquifer in batch experiments;(2) quantify rates of U(VI) desorption in column experiments with variable chemical conditions, and(3) quantify nonreactive tracer and U(VI) transport in field tests.

Research Proposal for the Design and Engineering Phase of a Solar Heating and Cooling System Experiment at the Warner Robins Public Library, Warner Robins, Georgia. Submitted to the United States Energy Research and Development Administration.

ERIC Educational Resources Information Center

Phillips, Warren H.; And Others

A number of reasons are advanced to include a solar heating and cooling experiment in a library building. The unique aspects of the experiment are to be a seasonally adjustable collector tilt and testing of a new generation of absorption air conditioners. After a brief description of the proposed experiment, the proposal contains forms filed by…

Skylab: The Second Manned Mission. A Scientific Harvest

NASA Technical Reports Server (NTRS)

1974-01-01

This black and white video presentation covers the Skylab launch activities and docking with unmanned SL-1 workshop. Included are observations of student experiments (the Minchmog minnows and Arabella, the spider), observations of student experiments, exercise routines, and the enabling of the Earth Resources Experiments Package. Also shown is planet Earth documentation, manned operation of the Apollo Telescope Mount for observations of the Sun and beyond, outside EVA activity, testing of the Astronaut Maneuvering Unit, experiments to explore industrial uses of space, and the Skylab living routine.

The MODE family of facility class experiments

NASA Technical Reports Server (NTRS)

Miller, David W.

1992-01-01

The objective of the Middeck 0-gravity Dynamics Experiment (MODE) is to characterize fundamental 0-g slosh behavior and obtain quantitative data on slosh force and spacecraft response for correlation of the analytical model. The topics are presented in viewgraph form and include the following: space results; STA objectives, requirements, and approach; comparison of ground to orbital data for the baseline configuration; conclusions of orbital testing; flight experiment resources; Middeck Active Control Experiment (MACE); MACE 1-G and 0-G models; and future efforts.

Bion 11 mission: primate experiments

NASA Technical Reports Server (NTRS)

Ilyin, E. A.; Korolkov, V. I.; Skidmore, M. G.; Viso, M.; Kozlovskaya, I. B.; Grindeland, R. E.; Lapin, B. A.; Gordeev, Y. V.; Krotov, V. P.; Fanton, J. W.;

Approaches and considerations for the assessment of immunotoxicity for environmental chemicals: a workshop summary.

PubMed

Boverhof, Darrell R; Ladics, Greg; Luebke, Bob; Botham, Jane; Corsini, Emanuela; Evans, Ellen; Germolec, Dori; Holsapple, Michael; Loveless, Scott E; Lu, Haitian; van der Laan, Jan Willem; White, Kimber L; Yang, Yung

2014-02-01

As experience is gained with toxicology testing and as new assays and technologies are developed, it is critical for stakeholders to discuss opportunities to advance our overall testing strategies. To facilitate these discussions, a workshop on practices for assessing immunotoxicity for environmental chemicals was held with the goal of sharing perspectives on immunotoxicity testing strategies and experiences, developmental immunotoxicity (DIT), and integrated and alternative approaches to immunotoxicity testing. Experiences across the chemical and pharmaceutical industries suggested that standard toxicity studies, combined with triggered-based testing approaches, represent an effective and efficient approach to evaluate immunotoxic potential. Additionally, discussions on study design, critical windows, and new guideline approaches and experiences identified important factors to consider before initiating DIT evaluations including assay choice and timing and the impact of existing adult data. Participants agreed that integrating endpoints into standard repeat-dose studies should be considered for fulfilling any immunotoxicity testing requirements, while also maximizing information and reducing animal use. Participants also acknowledged that in vitro evaluation of immunosuppression is complex and may require the use of multiple assays that are still being developed. These workshop discussions should contribute to developing an effective but more resource and animal efficient approach for evaluating chemical immunotoxicity. Copyright © 2013 Elsevier Inc. All rights reserved.

Military chemical warfare agent human subjects testing: part 2--long-term health effects among participants of U.S. military chemical warfare agent testing.

PubMed

Brown, Mark

2009-10-01

Military chemical warfare agent testing from World War I to 1975 produced thousands of veterans with concerns about how their participation affected their health. A companion article describes the history of these experiments, and how the lack of clinical data hampers evaluation of long-term health consequences. Conversely, much information is available about specific agents tested and their long-term health effects in other populations, which may be invaluable for helping clinicians respond effectively to the health care and other needs of affected veterans. The following review describes tested agents and their known long-term health consequences. Although hundreds of chemicals were tested, they fall into only about a half-dozen pharmaceutical classes, including common pharmaceuticals; anticholinesterase agents including military nerve agents and pesticides; anticholinergic glycolic acid esters such as atropine; acetylcholine reactivators such as 2-PAM; psychoactive compounds including cannabinoids, phencyclidine, and LSD; and irritants including tear gas and riot control agents.

Small Gas Bubble Experiment for Mitigation of Cavitation Damage and Pressure Waves in Short-pulse Mercury Spallation Targets

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wendel, Mark W; Felde, David K; Sangrey, Robert L

2014-01-01

Populations of small helium gas bubbles were introduced into a flowing mercury experiment test loop to evaluate mitigation of beam-pulse induced cavitation damage and pressure waves. The test loop was developed and thoroughly tested at the Spallation Neutron Source (SNS) prior to irradiations at the Los Alamos Neutron Science Center - Weapons Neutron Research Center (LANSCE-WNR) facility. Twelve candidate bubblers were evaluated over a range of mercury flow and gas injection rates by use of a novel optical measurement technique that accurately assessed the generated bubble size distributions. Final selection for irradiation testing included two variations of a swirl bubblermore » provided by Japan Proton Accelerator Research Complex (J-PARC) collaborators and one orifice bubbler developed at SNS. Bubble populations of interest consisted of sizes up to 150 m in radius with achieved gas void fractions in the 10^-5 to 10^-4 range. The nominal WNR beam pulse used for the experiment created energy deposition in the mercury comparable to SNS pulses operating at 2.5 MW. Nineteen test conditions were completed each with 100 pulses, including variations on mercury flow, gas injection and protons per pulse. The principal measure of cavitation damage mitigation was surface damage assessment on test specimens that were manually replaced for each test condition. Damage assessment was done after radiation decay and decontamination by optical and laser profiling microscopy with damaged area fraction and maximum pit depth being the more valued results. Damage was reduced by flow alone; the best mitigation from bubble injection was between half and a quarter that of flow alone. Other data collected included surface motion tracking by three laser Doppler vibrometers (LDV), loop wall dynamic strain, beam diagnostics for charge and beam profile assessment, embedded hydrophones and pressure sensors, and sound measurement by a suite of conventional and contact microphones.« less

Experience of Orthodontic Treatment and Symptoms of Temporomandibular Joint in South Korean Adults.

PubMed

Hwang, Sang-Hee; Park, Shin-Goo

2018-01-01

No epidemiological studies have targeted the association between experience of orthodontic treatment and symptoms of temporomandibular joint (TMJ) in a large adult population. In this study, we investigated whether experience of orthodontic treatment is associated with symptoms of TMJ in adults. We used data from the Fifth Korea National Health and Nutrition Examination Survey (KNHANES V), conducted in 2011. Trained dentists asked subjects to report their experience of orthodontic treatment and symptoms of TMJ. Overall, 5936 subjects aged over 19 yr were included in this study (2528 males). The data were analyzed using the chi-square test and multiple logistic regression tests. The group with experience of orthodontic treatment had more symptoms of TMJ than the group without orthodontic experience. After adjusting for all covariates (i.e., age, sex, marital status, income, education, stress, teeth injury, and occupation), the adjusted odds ratio was 2.53 (95%CI 1.74-3.67). Experience of orthodontic treatment could be related to increased symptoms of TMJ.

SOCIAL AND NON-SOCIAL CUEING OF VISUOSPATIAL ATTENTION IN AUTISM AND TYPICAL DEVELOPMENT

PubMed Central

Pruett, John R.; LaMacchia, Angela; Hoertel, Sarah; Squire, Emma; McVey, Kelly; Todd, Richard D.; Constantino, John N.; Petersen, Steven E.

2013-01-01

Three experiments explored attention to eye gaze, which is incompletely understood in typical development and is hypothesized to be disrupted in autism. Experiment 1 (n=26 typical adults) involved covert orienting to box, arrow, and gaze cues at two probabilities and cue-target times to test whether reorienting for gaze is endogenous, exogenous, or unique; experiment 2 (total n=80: male and female children and adults) studied age and sex effects on gaze cueing. Gaze cueing appears endogenous and may strengthen in typical development. Experiment 3 tested exogenous, endogenous, and/or gaze-based orienting in 25 typical and 27 Autistic Spectrum Disorder (ASD) children. ASD children made more saccades, slowing their reaction times; however, exogenous and endogenous orienting, including gaze cueing, appear intact in ASD. PMID:20809377

BIOMEX Experiment: Ultrastructural Alterations, Molecular Damage and Survival of the Fungus Cryomyces antarcticus after the Experiment Verification Tests.

PubMed

Pacelli, Claudia; Selbmann, Laura; Zucconi, Laura; De Vera, Jean-Pierre; Rabbow, Elke; Horneck, Gerda; de la Torre, Rosa; Onofri, Silvano

2017-06-01

The search for traces of extinct or extant life in extraterrestrial environments is one of the main goals for astrobiologists; due to their ability to withstand stress producing conditions, extremophiles are perfect candidates for astrobiological studies. The BIOMEX project aims to test the ability of biomolecules and cell components to preserve their stability under space and Mars-like conditions, while at the same time investigating the survival capability of microorganisms. The experiment has been launched into space and is being exposed on the EXPOSE-R2 payload, outside of the International Space Station (ISS) over a time-span of 1.5 years. Along with a number of other extremophilic microorganisms, the Antarctic cryptoendolithic black fungus Cryomyces antarcticus CCFEE 515 has been included in the experiment. Before launch, dried colonies grown on Lunar and Martian regolith analogues were exposed to vacuum, irradiation and temperature cycles in ground based experiments (EVT1 and EVT2). Cultural and molecular tests revealed that the fungus survived on rock analogues under space and simulated Martian conditions, showing only slight ultra-structural and molecular damage.

BIOMEX Experiment: Ultrastructural Alterations, Molecular Damage and Survival of the Fungus Cryomyces antarcticus after the Experiment Verification Tests

NASA Astrophysics Data System (ADS)

Pacelli, Claudia; Selbmann, Laura; Zucconi, Laura; De Vera, Jean-Pierre; Rabbow, Elke; Horneck, Gerda; de la Torre, Rosa; Onofri, Silvano

2017-06-01

The search for traces of extinct or extant life in extraterrestrial environments is one of the main goals for astrobiologists; due to their ability to withstand stress producing conditions, extremophiles are perfect candidates for astrobiological studies. The BIOMEX project aims to test the ability of biomolecules and cell components to preserve their stability under space and Mars-like conditions, while at the same time investigating the survival capability of microorganisms. The experiment has been launched into space and is being exposed on the EXPOSE-R2 payload, outside of the International Space Station (ISS) over a time-span of 1.5 years. Along with a number of other extremophilic microorganisms, the Antarctic cryptoendolithic black fungus Cryomyces antarcticus CCFEE 515 has been included in the experiment. Before launch, dried colonies grown on Lunar and Martian regolith analogues were exposed to vacuum, irradiation and temperature cycles in ground based experiments (EVT1 and EVT2). Cultural and molecular tests revealed that the fungus survived on rock analogues under space and simulated Martian conditions, showing only slight ultra-structural and molecular damage.

Research experiments at Hangar L

NASA Technical Reports Server (NTRS)

2000-01-01

Researchers work with wheat samples that are part of ground testing for the first International Space Station plant experiment, scheduled to fly in October 2001. From left are research scientist Oscar Monje and research technicians Lisa Ruffa and Ignacio Eraso. The payload process testing they are performing is one of many studies at the Biological Sciences Branch in the Spaceport Engineering and Technology Directorate at Kennedy Space Center. The branch's operations and research areas include life sciences Space Shuttle payloads, bioregenerative life-support for long-duration spaceflight and environmental/ecological stewardship.

A rocket-borne data-manipulation experiment using a microprocessor

NASA Technical Reports Server (NTRS)

Davis, L. L.; Smith, L. G.; Voss, H. D.

1979-01-01

The development of a data-manipulation experiment using a Z-80 microprocessor is described. The instrumentation is included in the payloads of two Nike Apache sounding rockets used in an investigation of energetic particle fluxes. The data from an array of solid-state detectors and an electrostatic analyzer is processed to give the energy spectrum as a function of pitch angle. The experiment performed well in its first flight test: Nike Apache 14.543 was launched from Wallops Island at 2315 EST on 19 June 1978. The system was designed to be easily adaptable to other data-manipulation requirements and some suggestions for further development are included.

Spontaneous Recovery But Not Reinstatement of the Extinguished Conditioned Eyeblink Response in the Rat

PubMed Central

Thanellou, Alexandra; Green, John T.

2011-01-01

Reinstatement, the return of an extinguished conditioned response (CR) after reexposure to the unconditioned stimulus (US), and spontaneous recovery, the return of an extinguished CR with the passage of time, are two of four well-established phenomena which demonstrate that extinction does not erase the conditioned stimulus (CS)-US association. However, reinstatement of extinguished eyeblink CRs has never been demonstrated and spontaneous recovery of extinguished eyeblink CRs has not been systematically demonstrated in rodent eyeblink conditioning. In Experiment 1, US reexposure was administered 24 hours prior to a reinstatement test. In Experiment 2, US reexposure was administered 5 min prior to a reinstatement test. In Experiment 3, a long, discrete cue (a houselight), present in all phases of training and testing, served as a context within which each trial occurred to maximize context processing, which in other preparations has been shown to be required for reinstatement. In Experiment 4, an additional group was included that received footshock exposure, rather than US reexposure, between extinction and test, and contextual freezing was measured prior to test. Spontaneous recovery was robust in Experiments 3 and 4. In Experiment 4, context freezing was strong in a group given footshock exposure but not in a group given eyeshock US reexposure. There was no reinstatement observed in any experiment. With stimulus conditions that produce eyeblink conditioning and research designs that produce reinstatement in other forms of classical conditioning, we observed spontaneous recovery but not reinstatement of extinguished eyeblink CRs. This suggests that reinstatement, but not spontaneous recovery, is a preparation- or substrate-dependent phenomenon. PMID:21517145

High Reynolds number tests of a NASA SC(3)-0712(B) airfoil in the Langley 0.3-meter transonic cryogenic tunnel

NASA Technical Reports Server (NTRS)

Johnson, W. G., Jr.; Hill, A. S.; Eichmann, O.

1985-01-01

A wind tunnel investigation of a NASA 12-percent-thick, advanced-technology supercritical airfoil was conducted in the Langley 0.3-Meter Transonic Cryogenic Tunnel (TCT). This investigation represents another in the series of NASA/U.S. industry two-dimensional airfoil studies to be completed in the Advanced Technology Airfoil Tests program. Test temperature was varied from 220 K to 96 K at pressures ranging from 1.2 to 4.3 atm. Mach number was varied from 0.60 to 0.80. These variables provided a Reynolds number range from 4,400,000 to 40,000,000 based on a 15.24-cm (6.0-in.) airfoil chord. This investigation was designed to test a NASA advanced-technology airfoil from low to flight-equivalent Reynolds numbers, provide experience in cryogenic wind tunnel model design and testing techniques, and demonstrate the suitability of the 0.3-m TCT as an airfoil test facility. The aerodynamic results are presented as integrated force and moment coefficients and pressure distributions. Data are included which demonstrate the effects of fixed transition, Mach number, and Reynolds number on the aerodynamic characteristics. Also included are remarks on the model design, the model structural integrity, and the overall test experience.

Photovoltaic Performance and Reliability Workshop summary

NASA Astrophysics Data System (ADS)

Kroposki, Benjamin

1997-02-01

The objective of the Photovoltaic Performance and Reliability Workshop was to provide a forum where the entire photovoltaic (PV) community (manufacturers, researchers, system designers, and customers) could get together and discuss technical issues relating to PV. The workshop included presentations from twenty-five speakers and had more than one hundred attendees. This workshop also included several open sessions in which the audience and speakers could discuss technical subjects in depth. Several major topics were discussed including: PV characterization and measurements, service lifetimes for PV devices, degradation and failure mechanisms for PV devices, standardization of testing procedures, AC module performance and reliability testing, inverter performance and reliability testing, standardization of utility interconnect requirements, experience from field deployed systems, and system certification.

The 1985 Goddard Space Flight Center Battery Workshop

NASA Technical Reports Server (NTRS)

Morrow, G. (Editor)

1986-01-01

The subjects covered include: advanced energy storage, lithium cell technology, nickel-cadmium design evaluation and component testing, simulated orbital cycling and flight experience, and nickel-hydrogen technology.

Virtual gaming simulation of a mental health assessment: A usability study.

PubMed

Verkuyl, Margaret; Romaniuk, Daria; Mastrilli, Paula

2018-05-18

Providing safe and realistic virtual simulations could be an effective way to facilitate the transition from the classroom to clinical practice. As nursing programs begin to include virtual simulations as a learning strategy; it is critical to first assess the technology for ease of use and usefulness. A virtual gaming simulation was developed, and a usability study was conducted to assess its ease of use and usefulness for students and faculty. The Technology Acceptance Model provided the framework for the study, which included expert review and testing by nursing faculty and nursing students. This study highlighted the importance of assessing ease of use and usefulness in a virtual game simulation and provided feedback for the development of an effective virtual gaming simulation. The study participants said the virtual gaming simulation was engaging, realistic and similar to a clinical experience. Participants found the game easy to use and useful. Testing provided the development team with ideas to improve the user interface. The usability methodology provided is a replicable approach to testing virtual experiences before a research study or before implementing virtual experiences into curriculum. Copyright © 2018 Elsevier Ltd. All rights reserved.

Construction and Initial Tests of MAIZE: 1 MA LTD-Driven Z-Pinch *

NASA Astrophysics Data System (ADS)

Gilgenbach, R. M.; Gomez, M. R.; Zier, J. C.; Tang, W.; French, D. M.; Lau, Y. Y.; Mazarakis, M. G.; Cuneo, M. E.; Johnston, M. D.; Oliver, B. V.; Mehlhorn, T. A.; Kim, A. A.; Sinebryukhov, V. A.

2008-11-01

We report construction and initial testing of a 1-MA Linear Transformer Driver (LTD), The Michigan Accelerator for Inductive Z-pinch Experiments, (MAIZE). This machine, the first of its type to reach the USA, is based on the joint HCEI, Sandia Laboratories, and UM development effort. The compact LTD uses 80 capacitors and 40 spark gap switches, in 40 ``bricks'', to deliver 1 MA, 100 kV pulses with 70 ns risetime into a matched resistive load. Test results will be presented for a single brick and the full LTD. Design and construction will be presented of a low-inductance MITL. Experimental research programs under design and construction at UM include: a) Studies of Magneto-Raleigh-Taylor Instability of planar foils, and b) Vacuum convolute studies including cathode and anode plasma. Theory and simulation results will be presented for these planned experiments. Initial experimental designs and moderate-current feasibility experiments will be discussed. *Research supported by U. S. DoE through Sandia National Laboratories award document numbers 240985, 768225, 790791 and 805234 to the UM. MRG supported by NNSA Fellowship and JCZ supported by NPSC Fellowship / Sandia National Labs.

'Chain pooling' model selection as developed for the statistical analysis of a rotor burst protection experiment

NASA Technical Reports Server (NTRS)

Holms, A. G.

1977-01-01

A statistical decision procedure called chain pooling had been developed for model selection in fitting the results of a two-level fixed-effects full or fractional factorial experiment not having replication. The basic strategy included the use of one nominal level of significance for a preliminary test and a second nominal level of significance for the final test. The subject has been reexamined from the point of view of using as many as three successive statistical model deletion procedures in fitting the results of a single experiment. The investigation consisted of random number studies intended to simulate the results of a proposed aircraft turbine-engine rotor-burst-protection experiment. As a conservative approach, population model coefficients were chosen to represent a saturated 2 to the 4th power experiment with a distribution of parameter values unfavorable to the decision procedures. Three model selection strategies were developed.

Overview of the 2009 and 2011 Sayarim Infrasound Calibration Experiments

NASA Astrophysics Data System (ADS)

Fee, D.; Waxler, R.; Drob, D.; Gitterman, Y.; Given, J.

2012-04-01

The establishment of the International Monitoring System (IMS) of the Comprehensive Nuclear-Test-Ban Treaty Organization (CTBTO) has stimulated infrasound research and development. However, as the network comes closer to completion there exists a lack of large, well-constrained sources to test the network and its capabilities. Also, significant uncertainties exist in long-range acoustic propagation due to a dynamic, difficult to characterize atmosphere, particularly the thermosphere. In 2009 and 2011 three large scale infrasound calibration experiments were performed in Europe, the Middle East, Africa, and Asia. The goal of the calibration experiments were to test the IMS infrasound network and validate atmospheric and propagation models with large, well-constrained infrasound sources. This presentation provides an overview of the calibration experiments, including deployment, atmospheric conditions during the experiments, explosion characterization, infrasonic signal detection and identification, and a discussion of the results and implications. Each calibration experiment consisted of singular surface detonation of explosives with nominal weights of 82, 10.24, and 102.08 tons on 26 August 2009, 24 January 2011, and 26 January 2011, respectively. These explosions were designed and conducted by the Geophysical Institute of Israel at Sayarim Military Range, Israel and produced significant infrasound detected by numerous permanent and temporary infrasound arrays in the region. The 2009 experiment was performed in the summer to take advantage of the westerly stratospheric winds. Infrasonic arrivals were detected by both IMS and temporary arrays deployed to the north and west of the source, including clear stratospheric arrivals and thermospheric arrivals with low celerities. The 2011 experiment was performed during the winter, when strong easterly stratospheric winds dominated in addition to a strong tropospheric jet (the jet stream). These wind jets allowed detection out to 6500 km, in addition to multiple tropospheric, stratospheric, and thermospheric arrivals at arrays deployed to the east. These experiments represented a considerable, successful collaboration between the CTBTO and numerous other groups and will provide a rich ground-truth dataset for detailed infrasound studies in the future.

Virginity Testing Beyond a Medical Examination

PubMed Central

Robatjazi, Mehri; Simbar, Masoumeh; Nahidi, Fatemeh; Gharehdaghi, Jaber; Emamhadi, Mohammadali; Vedadhir, Abou-Ali; Alavimajd, Hamid

2016-01-01

Apart from religious values, virginity is important in different communities because of its prominent role in reducing sexually transmitted diseases and teen pregnancies. Even though virginity testing has been proclaimed an example of violence against women by the World Health Organization, it is still conducted in many countries, including Iran. 16 in-depth, semi-structured interviews were conducted with participants aged 32 to 60 years to elucidate the perceptions and experiences of Iranian examiners of virginity testing. The perception and experience of examiners were reflected in five main themes. The result of this study indicated that virginity testing is more than a medical examination, considering the cultural factors involved and its overt and covert consequences. In Iran, testing is performed for both formal and informal reasons, and examiners view such testing with ambiguity about the accuracy and certainty of the diagnosis and uncertainty about ethics and reproductive rights. Examiners are affected by the overt and covert consequences of virginity testing, beliefs and cultural values underlying virginity testing, and informal and formal reasons for virginity testing. PMID:26925894

Extravehicular activity welding experiment

NASA Technical Reports Server (NTRS)

Watson, J. Kevin

1989-01-01

The In-Space Technology Experiments Program (INSTEP) provides an opportunity to explore the many critical questions which can only be answered by experimentation in space. The objective of the Extravehicular Activity Welding Experiment definition project was to define the requirements for a spaceflight experiment to evaluate the feasibility of performing manual welding tasks during EVA. Consideration was given to experiment design, work station design, welding hardware design, payload integration requirements, and human factors (including safety). The results of this effort are presented. Included are the specific objectives of the flight test, details of the tasks which will generate the required data, and a description of the equipment which will be needed to support the tasks. Work station requirements are addressed as are human factors, STS integration procedures and, most importantly, safety considerations. A preliminary estimate of the cost and the schedule for completion of the experiment through flight and postflight analysis are given.

The Penefit of Salience: Salient Accented, but Not Unaccented Words Reveal Accent Adaptation Effects

PubMed Central

Grohe, Ann-Kathrin; Weber, Andrea

2016-01-01

In two eye-tracking experiments, the effects of salience in accent training and speech accentedness on spoken-word recognition were investigated. Salience was expected to increase a stimulus' prominence and therefore promote learning. A training-test paradigm was used on native German participants utilizing an artificial German accent. Salience was elicited by two different criteria: production and listening training as a subjective criterion and accented (Experiment 1) and canonical test words (Experiment 2) as an objective criterion. During training in Experiment 1, participants either read single German words out loud and deliberately devoiced initial voiced stop consonants (e.g., Balken—“beam” pronounced as *Palken), or they listened to pre-recorded words with the same accent. In a subsequent eye-tracking experiment, looks to auditorily presented target words with the accent were analyzed. Participants from both training conditions fixated accented target words more often than a control group without training. Training was identical in Experiment 2, but during test, canonical German words that overlapped in onset with the accented words from training were presented as target words (e.g., Palme—“palm tree” overlapped in onset with the training word *Palken) rather than accented words. This time, no training effect was observed; recognition of canonical word forms was not affected by having learned the accent. Therefore, accent learning was only visible when the accented test tokens in Experiment 1, which were not included in the test of Experiment 2, possessed sufficient salience based on the objective criterion “accent.” These effects were not modified by the subjective criterion of salience from the training modality. PMID:27375540

The Spacecraft Fire Experiment (Saffire) - Objectives, Development and Status

NASA Technical Reports Server (NTRS)

Schoren, William; Ruff, Gary A.; Urban, David L.

2016-01-01

Since 2012, the Spacecraft Fire Experiment (Saffire) has been under development by the Spacecraft Fire Safety Demonstration (SFS Demo) project that is funded by NASA's Advanced Exploration Systems Division in the Human Exploration and Operations Mission Directorate. The overall objective of this project is to reduce the uncertainty and risk associated with the design of spacecraft fire safety systems for NASA's exploration missions. This is accomplished by defining, developing, and conducting experiments that address gaps in spacecraft fire safety knowledge and capabilities identified by NASA's Fire Safety System Maturation Team. This paper describes the three Spacecraft Fire Experiments (Saffire-I, -II, and -III) that were developed at NASA-GRC and that will conduct a series of material flammability tests in low-gravity and at length scales that are realistic for a spacecraft fire. The experiments will be conducted in Orbital ATK's Cygnus vehicle after it has unberthed from the International Space Station. The tests will be fully automated with the data downlinked at the conclusion of the test and before the Cygnus vehicle reenters the atmosphere. The objectives of these experiments are to (1) determine how rapidly a large scale fire grows in low-gravity and (2) investigate the low-g flammability limits compared to those obtained in NASA's normal gravity material flammability screening test. The hardware for these experiments has been completed and is awaiting their respective launches, all planned for 2016. This paper will review the objectives of these experiments and how they address several of the knowledge gaps for NASA's exploration missions. The hardware development will be discussed including several novel approaches that were taken for testing and evaluation of these series payloads. The status of the missions and operational status will also be presented.

An Investigation of the Connection between Outdoor Orientation and Thriving

ERIC Educational Resources Information Center

Rude, Wally James; Bobilya, Andrew J.; Bell, Brent J.

2017-01-01

This study explored the contribution of outdoor orientation experiences to student thriving. Participants included 295 first-year college students from three institutions across North America. A thriving model was tested using structural equation modeling and included the following variables: outdoor orientation, thriving, involvement,…

Lithium Circuit Test Section Design and Fabrication

NASA Technical Reports Server (NTRS)

Godfroy, Thomas; Garber, Anne

2006-01-01

The Early Flight Fission - Test Facilities (EFF-TF) team has designed and built an actively pumped lithium flow circuit. Modifications were made to a circuit originally designed for NaK to enable the use of lithium that included application specific instrumentation and hardware. Component scale freeze/thaw tests were conducted to both gain experience with handling and behavior of lithium in solid and liquid form and to supply anchor data for a Generalized Fluid System Simulation Program (GFSSP) model that was modified to include the physics for freeze/thaw transitions. Void formation was investigated. The basic circuit components include: reactor segment, lithium to gas heat exchanger, electromagnetic (EM) liquid metal pump, load/drain reservoir, expansion reservoir, instrumentation, and trace heaters. This paper will discuss the overall system design and build and the component testing findings.

Lithium Circuit Test Section Design and Fabrication

NASA Astrophysics Data System (ADS)

Godfroy, Thomas; Garber, Anne; Martin, James

2006-01-01

The Early Flight Fission - Test Facilities (EFF-TF) team has designed and built an actively pumped lithium flow circuit. Modifications were made to a circuit originally designed for NaK to enable the use of lithium that included application specific instrumentation and hardware. Component scale freeze/thaw tests were conducted to both gain experience with handling and behavior of lithium in solid and liquid form and to supply anchor data for a Generalized Fluid System Simulation Program (GFSSP) model that was modified to include the physics for freeze/thaw transitions. Void formation was investigated. The basic circuit components include: reactor segment, lithium to gas heat exchanger, electromagnetic (EM) liquid metal pump, load/drain reservoir, expansion reservoir, instrumentation, and trace heaters. This paper discusses the overall system design and build and the component testing findings.

The use of photogrammetric and stereophotogrammetric methods in aerodynamic experiments

NASA Astrophysics Data System (ADS)

Shmyreva, V. N.; Iakovlev, V. A.

The possibilities afforded by photogrammetry and stereophotogrammetry in current aerodynamic experiments, methods of image recording, and observation data processing are briefly reviewed. Some specific experiments illustrating the application of stereophotogrammetry are described. The applications discussed include the monitoring of model position in wind tunnels, determination of model deformations and displacements, determination of the deformations of real structural elements in static strength tests, and solution of a variety of problems in hydrodynamics.

Attitudes about Advances in Sweat Patch Testing in Drug Courts: Insights from a Case Study in Southern California

ERIC Educational Resources Information Center

Polzer, Katherine

2010-01-01

Drug courts are reinventing the drug testing framework by experimenting with new methods, including use of the sweat patch. The sweat patch is a band-aid like strip used to monitor drug court participants. The validity and reliability of the sweat patch as an effective testing method was examined, as well as the effectiveness, meaning how likely…

THAI Multi-Compartment Containment Test Program

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kanzleiter, T.; Poss, G.; Funke, F.

2006-07-01

The THAI experimental programme includes combined-effect investigations on thermal hydraulics, hydrogen, and fission product (iodine and aerosols) behaviour in LWR containments under severe accident conditions. An overview on the experiments performed up to now and on the future test program is presented, in combination with a selection of typical results to illustrate the versatility of the test facility and the broad variety of topics investigated. (authors)

Dietary effects on object recognition: The impact of high-fat high-sugar diets on recollection and familiarity-based memory.

PubMed

Tran, Dominic M D; Westbrook, R Frederick

2018-05-31

Exposure to a high-fat high-sugar (HFHS) diet rapidly impairs novel-place- but not novel-object-recognition memory in rats (Tran & Westbrook, 2015, 2017). Three experiments sought to investigate the generality of diet-induced cognitive deficits by examining whether there are conditions under which object-recognition memory is impaired. Experiments 1 and 3 tested the strength of short- and long-term object-memory trace, respectively, by varying the interval of time between object familiarization and subsequent novel object test. Experiment 2 tested the effect of increasing working memory load on object-recognition memory by interleaving additional object exposures between familiarization and test in an n-back style task. Experiments 1-3 failed to detect any differences in object recognition between HFHS and control rats. Experiment 4 controlled for object novelty by separately familiarizing both objects presented at test, which included one remote-familiar and one recent-familiar object. Under these conditions, when test objects differed in their relative recency, HFHS rats showed a weaker memory trace for the remote object compared to chow rats. This result suggests that the diet leaves intact recollection judgments, but impairs familiarity judgments. We speculate that the HFHS diet adversely affects "where" memories as well as the quality of "what" memories, and discuss these effects in relation to recollection and familiarity memory models, hippocampal-dependent functions, and episodic food memories. (PsycINFO Database Record (c) 2018 APA, all rights reserved).

Alternate methodologies to experimentally investigate shock initiation properties of explosives

NASA Astrophysics Data System (ADS)

Svingala, Forrest R.; Lee, Richard J.; Sutherland, Gerrit T.; Benjamin, Richard; Boyle, Vincent; Sickels, William; Thompson, Ronnie; Samuels, Phillip J.; Wrobel, Erik; Cornell, Rodger

2017-01-01

Reactive flow models are desired for new explosive formulations early in the development stage. Traditionally, these models are parameterized by carefully-controlled 1-D shock experiments, including gas-gun testing with embedded gauges and wedge testing with explosive plane wave lenses (PWL). These experiments are easy to interpret due to their 1-D nature, but are expensive to perform and cannot be performed at all explosive test facilities. This work investigates alternative methods to probe shock-initiation behavior of new explosives using widely-available pentolite gap test donors and simple time-of-arrival type diagnostics. These experiments can be performed at a low cost at most explosives testing facilities. This allows experimental data to parameterize reactive flow models to be collected much earlier in the development of an explosive formulation. However, the fundamentally 2-D nature of these tests may increase the modeling burden in parameterizing these models and reduce general applicability. Several variations of the so-called modified gap test were investigated and evaluated for suitability as an alternative to established 1-D gas gun and PWL techniques. At least partial agreement with 1-D test methods was observed for the explosives tested, and future work is planned to scope the applicability and limitations of these experimental techniques.

Implicit memory. Retention without remembering.

PubMed

Roediger, H L

1990-09-01

Explicit measures of human memory, such as recall or recognition, reflect conscious recollection of the past. Implicit tests of retention measure transfer (or priming) from past experience on tasks that do not require conscious recollection of recent experiences for their performance. The article reviews research on the relation between explicit and implicit memory. The evidence points to substantial differences between standard explicit and implicit tests, because many variables create dissociations between these tests. For example, although pictures are remembered better than words on explicit tests, words produce more priming than do pictures on several implicit tests. These dissociations may implicate different memory systems that subserve distinct memorial functions, but the present argument is that many dissociations can be understood by appealing to general principles that apply to both explicit and implicit tests. Phenomena studied under the rubric of implicit memory may have important implications in many other fields, including social cognition, problem solving, and cognitive development.

A Historical Perspective on Dynamics Testing at the Langley Research Center

NASA Technical Reports Server (NTRS)

Horta, Lucas G.; Kvaternik, Raymond G.; Hanks, Brantley R.

2000-01-01

The experience and advancement of Structural dynamics testing for space system applications at the Langley Research Center of the National Aeronautics and Space Administration (NASA) over the past four decades is reviewed. This experience began in the 1960's with the development of a technology base using a variety of physical models to explore dynamic phenomena and to develop reliable analytical modeling capability for space systems. It continued through the 1970's and 80's with the development of rapid, computer-aided test techniques, the testing of low-natural frequency, gravity-sensitive systems, the testing of integrated structures with active flexible motion control, and orbital flight measurements, It extended into the 1990's where advanced computerized system identification methods were developed for estimating the dynamic states of complex, lightweight, flexible aerospace systems, The scope of discussion in this paper includes ground and flight tests and summarizes lessons learned in both successes and failures.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bamberger, Judith A.; Piepel, Gregory F.; Enderlin, Carl W.

Understanding how uncertainty manifests itself in complex experiments is important for developing the testing protocol and interpreting the experimental results. This paper describes experimental and measurement uncertainties, and how they can depend on the order of performing experimental tests. Experiments with pulse-jet mixers in tanks at three scales were conducted to characterize the performance of transient-developing periodic flows in Newtonian slurries. Other test parameters included the simulant, solids concentration, and nozzle exit velocity. Critical suspension velocity and cloud height were the metrics used to characterize Newtonian slurry flow associated with mobilization and mixing. During testing, near-replicate and near-repeat tests weremore » conducted. The experimental results were used to quantify the combined experimental and measurement uncertainties using standard deviations and percent relative standard deviations (%RSD) The uncertainties in critical suspension velocity and cloud height tend to increase with the values of these responses. Hence, the %RSD values are the more appropriate summary measure of near-replicate testing and measurement uncertainty.« less

Awareness of Pap testing and factors associated with intent to undergo Pap testing by level of sexual experience in unmarried university students in Korea: results from an online survey

PubMed Central

2014-01-01

Background Young and unmarried women have not been a target group for cervical cancer prevention in Korea. No previous studies have investigated the awareness of Pap testing, the intention to undergo Pap testing, or the factors associated with that intention, in this group of women. This information would be useful for an expansion in the focus of primary cervical cancer prevention. This study aimed to compare the awareness of Pap testing between groups of unmarried university students in Korea, and to investigate the factors associated with the intention to undergo Pap testing, by level of sexual experience. Methods A total of 475 unmarried university students who had never undergone a Pap test completed a web-based survey. Differences in awareness of the importance of the Pap test, confidence in Pap testing, intention to undergo the test, attitudes, subjective norms, perceived control, stigma, and shame by level of sexual experience were analysed using independent t-tests. Associations between measurement variables and intention to undergo Pap testing were analysed using correlation analysis. Variables yielding significant associations (p < 0.05) were included in a stepwise multiple regression model of intention to undergo Pap testing. Results Most participants perceived that the need for regular Pap testing was less important (score, 77.76) than other methods of cervical cancer prevention. They were not confident that is was an effective method of cervical cancer prevention for themselves (score, 59.56). There were differences in confidence in Pap testing and in the factors associated with intention to undergo Pap testing between sexually experienced and sexually inexperienced students. Regardless of level of sexual experience, the subjective norm was the most important predictor of intention to undergo Pap testing. Conclusions There was a low level of Pap screening awareness among the students. The factors associated with intention to undergo Pap testing differed by level of sexual experience. Social influence was an important factor that could be used to increase the intention to receive a Pap test in the university student population. Strategies to increase the intention to undergo Pap screening should be introduced and should be adapted to the level of sexual experience. PMID:25163938

Radiology in Medical Education: A Pediatric Radiology Elective as a Template for Other Radiology Courses.

PubMed

Hilmes, Melissa A; Hyatt, Eddie; Penrod, Cody H; Fleming, Amy E; Singh, Sudha P

2016-03-01

Traditionally, the pediatric radiology elective for medical students and pediatric residents constituted a morning teaching session focused mainly on radiography and fluoroscopy. A more structured elective was desired to broaden the exposure to more imaging modalities, create a more uniform educational experience, and include assessment tools. In 2012, an introductory e-mail and formal syllabus, including required reading assignments, were sent to participants before the start date. A rotating weekly schedule was expanded to include cross-sectional imaging (ultrasound, CT, MR) and nuclear medicine. The schedule could accommodate specific goals of the pediatric resident or medical student, as requested. Starting in 2013, an online pre-test and post-test were developed, as well as an online end-of-rotation survey specific to the pediatric radiology elective. Taking the Image Gently pledge was required. A scavenger hunt tool, cue cards, and electronic modules were added. Pre-test and post-test scores, averaged over 2 years, showed improvement in radiology knowledge, with scores increasing by 27% for medical students and 21% for pediatric residents. Surveys at the end of the elective were overwhelmingly positive, with constructive criticism and complimentary comments. We have successfully created an elective experience in radiology that dedicates time to education while preserving the workflow of radiologists. We have developed tools to provide a customized experience with many self-directed learning opportunities. Our tools and techniques are easily translatable to a general or adult radiology elective. Copyright © 2016 American College of Radiology. Published by Elsevier Inc. All rights reserved.

Evaluation of a thyrotropin-releasing hormone solution stored at room temperature for pituitary pars intermedia dysfunction testing in horses.

PubMed

Goodale, Lindsay; Frank, Nicholas; Hermida, Pilar; D'Oench, Sarah

2015-05-01

To determine whether plasma ACTH concentrations vary following administration of a thyrotropin-releasing hormone (TRH) solution prepared for research purposes and stored at -20°C (rTRH) or prepared by a compounding pharmacy and stored at room temperature (approx 22°C; cTRH). 34 adult horses. The study consisted of 2 experiments. In experiment 1, each horse underwent 2 TRH stimulation tests separated by 24 hours; 10 horses were administered cTRH for the first test and rTRH for the second test (group 1), 10 horses were administered rTRH for the first test and cTRH for the second test (group 2), and 10 horses were administered rTRH for both tests (group 3). Plasma ACTH concentrations were measured at 0 (baseline) and 30 minutes after TRH administration and the delta ACTH responses (change in ACTH concentration after TRH administration) were calculated. In experiment 2, the design was the same as that for experiment 1 except there were 14 days between tests, ACTH was measured at 0 and 10 minutes after TRH administration, and 11, 9, and 10 horses were assigned to groups 1, 2, and 3, respectively. Adverse effects associated with TRH administration included transient coughing and yawning. In experiment 1, the median delta ACTH response for the second test was significantly lower than that for the first test for all groups. In experiment 2, the median delta ACTH response did not differ significantly between the first and second tests for any group, ACTH concentrations after rTRH administration were positively correlated (rs = 0.95) with those after cTRH administration, and the mean ± SD bias in post-TRH ACTH concentration between rTRH and cTRH was 2.9 ± 12.4 pg/mL. Results indicated that the TRH stimulation test should not be repeated within 24 hours, and cTRH solution stored at room temperature could be used to effectively perform TRH stimulation testing in horses.

The application test system: An approach to technology transfer. [USDA aerospace and remote sensing information requirements

NASA Technical Reports Server (NTRS)

Aaronson, A. C.; Buelow, K.; David, F. C.; Packard, R. L.; Ravet, F. W. (Principal Investigator)

1979-01-01

The latest satellite and computer processing and analysis technologies were tested and evaluated in terms of their application feasibility. Technologies evaluated include those developed, tested, and evaluated by the LACIE, as well as candidate technologies developed by the research community and private industry. The implementation of the applications test system and the technology transfer experience between the LACIE and the applications test system is discussed highlighting the approach, the achievements, and the shortcomings.

The visual cliff's forgotten menagerie: rats, goats, babies, and myth-making in the history of psychology.

PubMed

Rodkey, Elissa N

2015-01-01

Eleanor Gibson and Richard Walk's famous visual cliff experiment is one of psychology's classic studies, included in most introductory textbooks. Yet the famous version which centers on babies is actually a simplification, the result of disciplinary myth-making. In fact the visual cliff's first subjects were rats, and a wide range of animals were tested on the cliff, including chicks, turtles, lambs, kid goats, pigs, kittens, dogs, and monkeys. The visual cliff experiment was more accurately a series of experiments, employing varying methods and a changing apparatus, modified to test different species. This paper focuses on the initial, nonhuman subjects of the visual cliff, resituating the study in its original experimental logic, connecting it to the history of comparative psychology, Gibson's interest in comparative psychology, as well as gender-based discrimination. Recovering the visual cliff's forgotten menagerie helps to counter the romanticization of experimentation by focusing on the role of extrascientific factors, chance, complexity, and uncertainty in the experimental process. © 2015 Wiley Periodicals, Inc.

Perception and Control of Simulated Self Motion. Final Report for the Period April 1983-March 1987.

ERIC Educational Resources Information Center

Owen, Dean H.; And Others

This report includes three experiment sections. The first experiment tested sensitivity to loss in altitude and demonstrated that: (1) preview effects led to adaptation; (2) sensitivity decreased with higher flow rates; and (3) sensitivity increased with higher optical texture densities and fractional loss. The second and third experiments…

Testing Plastic Deformations of Materials in the Introductory Undergraduate Mechanics Laboratory

ERIC Educational Resources Information Center

Romo-Kroger, C. M.

2012-01-01

Normally, a mechanics laboratory at the undergraduate level includes an experiment to verify compliance with Hooke's law in materials, such as a steel spring and an elastic rubber band. Stress-strain curves are found for these elements. Compression in elastic bands is practically impossible to achieve due to flaccidity. A typical experiment for…

Tested Demonstrations: Buffer Capacity of Various Acetic Acid-Sodium Acetate Systems: A Lecture Experiment.

ERIC Educational Resources Information Center

Donahue, Craig J.; Panek, Mary G.

1985-01-01

Background information and procedures are provided for a lecture experiment which uses indicators to illustrate the concept of differing buffer capacities by titrating acetic acid/sodium acetate buffers with 1.0 molar hydrochloric acid and 1.0 molar sodium hydroxide. A table with data used to plot the titration curve is included. (JN)

Water, Water Everywhere, But....Notes for the Teacher, Report Writing Directions and Experiments.

ERIC Educational Resources Information Center

Jacobson, Cliff

Provided in this teaching package are materials that clearly and simply unveil the mysteries of water pollution. Materials, written on an approximate seventh-grade level, include: (1) a student reading unit; (2) water quality factors pamphlet; (3) experiments; and (4) teacher's guide to field testing a local waterway. The student reading unit is…

Classroom Experiences in an Engineering Design Graphics Course with a CAD/CAM Extension.

ERIC Educational Resources Information Center

Barr, Ronald E.; Juricic, Davor

1997-01-01

Reports on the development of a new CAD/CAM laboratory experience for an Engineering Design Graphics (EDG) course. The EDG curriculum included freehand sketching, introduction to Computer-Aided Design and Drafting (CADD), and emphasized 3-D solid modeling. Reviews the project and reports on the testing of the new laboratory components which were…

Research study on stellar X-ray imaging experiment, volume 2

NASA Technical Reports Server (NTRS)

Wilson, H. H.; Vanspeybroeck, L. P.

1972-01-01

A review of the scientific objectives of an integrated X-ray orbiting telescope facility is presented. A set of observations to be conducted to achieve the objectives of the research are described. The techniques and equipment used in the experiment are defined. The configuration of the facility and the specifications of the test equipment are included.

Thermosyphon Flooding in Reduced Gravity Environments Test Results

NASA Technical Reports Server (NTRS)

Gibson, Marc A.; Jaworske, Donald A.; Sanzi, Jim; Ljubanovic, Damir

2013-01-01

The condenser flooding phenomenon associated with gravity aided two-phase thermosyphons was studied using parabolic flights to obtain the desired reduced gravity environment (RGE). The experiment was designed and built to test a total of twelve titanium water thermosyphons in multiple gravity environments with the goal of developing a model that would accurately explain the correlation between gravitational forces and the maximum axial heat transfer limit associated with condenser flooding. Results from laboratory testing and parabolic flights are included in this report as part I of a two part series. The data analysis and correlations are included in a follow on paper.

Radon: The Invisible Invader.

ERIC Educational Resources Information Center

School Leader, 1987

1987-01-01

A brief background on indoor radon and the health risks associated with radon exposure, with special emphasis on nonresidential buildings. One school district's experience in radon testing and monitoring is included. (MLF)

Supplement to the Carcinogenic Potency Database (CPDB): results of animal bioassays published in the general literature in 1993 to 1994 and by the National Toxicology Program in 1995 to 1996.

PubMed Central

Gold, L S; Manley, N B; Slone, T H; Rohrbach, L

1999-01-01

The Carcinogenic Potency Database (CPDB) is a systematic and unifying analysis of results of chronic, long-term cancer tests. This paper presents a supplemental plot of the CPDB, including 513 experiments on 157 test compounds published in the general literature in 1993 and 1994 and in Technical Reports of the National Toxicology Program in 1995 and 1996. The plot standardizes the experimental results (whether positive or negative for carcinogenicity), including qualitative data on strain, sex, route of compound administration, target organ, histopathology, and author's opinion and reference to the published paper, as well as quantitative data on carcinogenic potency, statistical significance, tumor incidence, dose-response curve shape, length of experiment, duration of dosing, and dose rate. A numerical description of carcinogenic potency, the TD(subscript)50(/subscript), is estimated for each set of tumor incidence data reported. When added to the data published earlier, the CPDB now includes results of 5,620 experiments on 1,372 chemicals that have been reported in 1,250 published papers and 414 National Cancer Institute/National Toxicology Program Technical Reports. The plot presented here includes detailed analyses of 25 chemicals tested in monkeys for up to 32 years by the National Cancer Institute. Half the rodent carcinogens that were tested in monkeys were not carcinogenic, despite usually strong evidence of carcinogenicity in rodents and/or humans. Our analysis of possible explanatory factors indicates that this result is due in part to the fact that the monkey studies lacked power to detect an effect compared to standard rodent bioassays. Factors that contributed to the lack of power are the small number of animals on test; a stop-exposure protocol for model rodent carcinogens; in a few cases, toxic doses that resulted in stoppage of dosing or termination of the experiment; and in a few cases, low doses administered to monkeys or early termination of the experiment even though the doses were not toxic. Among chemicals carcinogenic in both monkeys and rodents, there is some support for target site concordance, but it is primarily restricted to liver tumors. Potency values are highly correlated between rodents and monkeys. The plot in this paper can be used in conjunction with the earlier results published in the CRC Handbook of Carcinogenic Potency and Genotoxicity Databases [Gold LS, Zeiger E, eds. Boca Raton FL:CRC Press, 1997] and with our web site (http://potency.berkeley.edu), which includes a guide to the plot of the database, a complete description of the numerical index of carcinogenic potency (TD50), and a discussion of the sources of data, the rationale for the inclusion of particular experiments and particular target sites, and the conventions adopted in summarizing the literature. Two summary tables permit easy access to the literature of animal cancer tests by target organ and by chemical. For readers using the CPDB extensively, a combined plot on diskette or other format is available from the first author. It includes all results published earlier and in this paper, ordered alphabetically by chemical. A SAS database is also available. PMID:10421768

Advanced Capabilities for Wind Tunnel Testing in the 21st Century

NASA Technical Reports Server (NTRS)

Kegelman, Jerome T.; Danehy, Paul M.; Schwartz, Richard J.

2010-01-01

Wind tunnel testing methods and test technologies for the 21st century using advanced capabilities are presented. These capabilities are necessary to capture more accurate and high quality test results by eliminating the uncertainties in testing and to facilitate verification of computational tools for design. This paper discusses near term developments underway in ground testing capabilities, which will enhance the quality of information of both the test article and airstream flow details. Also discussed is a selection of new capability investments that have been made to accommodate such developments. Examples include advanced experimental methods for measuring the test gas itself; using efficient experiment methodologies, including quality assurance strategies within the test; and increasing test result information density by using extensive optical visualization together with computed flow field results. These points could be made for both major investments in existing tunnel capabilities or for entirely new capabilities.

Science Data Report for the Optical Properties Monitor (OPM) Experiment

NASA Technical Reports Server (NTRS)

Wilkes, Donald R.; Zwiener, James M.

1999-01-01

Long term stability of spacecraft materials when exposed to the space environment continues to be a major area of investigation. The natural and induced environment surrounding a spacecraft can decrease material performance and limit useful lifetimes. The Optical Properties Monitor (OPM) experiment provided the capability to perform the important flight testing of materials and was flown on the Russian Mir Station to study the long term effects of the natural and induced space environment on materials. The core of the OPM in-flight analysis was three independent optical instruments. These instruments included an integrating sphere spectral reflectometer, a vacuum ultraviolet spectrometer, and a Total Integrated Scatter instrument. The OPM also monitored selected components of the environment including molecular contamination. The OPM was exposed on the exterior of the Mir Docking Module for approximately 8-1/2 months. This report describes the OPM experiment, a brief background of its development, program organization, experiment description, mission overview including space environment definition, performance overview, materials data including flight and ground data, in-depth post flight analysis including ground analysis measurements and a summary discussion of the findings and results.

Effectiveness of herbicides for control of hairy vetch (Vicia villosa) in winter wheat

USDA-ARS?s Scientific Manuscript database

We conducted a field experiment in 2009-10 at Pennsylvania and Maryland locations, and repeated it in 2010-11, to test the effectiveness of post-emergent herbicides applied at fall and spring timings on seeded hairy vetch in winter wheat. We tested 16 herbicide treatment combinations that included ...

Violating Conventional Wisdom in Multiple Choice Test Construction

ERIC Educational Resources Information Center

Taylor, Annette Kujawski

2005-01-01

This research examined 2 elements of multiple-choice test construction, balancing the key and optimal number of options. In Experiment 1 the 3 conditions included a balanced key, overrepresentation of a and b responses, and overrepresentation of c and d responses. The results showed that error-patterns were independent of the key, reflecting…

Recognition Memory: A Review of the Critical Findings and an Integrated Theory for Relating Them

ERIC Educational Resources Information Center

Malmberg, Kenneth J.

2008-01-01

The development of formal models has aided theoretical progress in recognition memory research. Here, I review the findings that are critical for testing them, including behavioral and brain imaging results of single-item recognition, plurality discrimination, and associative recognition experiments under a variety of testing conditions. I also…

Medical microbiological analysis of Apollo-Soyuz test project crewmembers

NASA Technical Reports Server (NTRS)

Taylor, G. R.; Zaloguev, S. N.

1976-01-01

The procedures and results of the Microbial Exchange Experiment (AR-002) of the Apollo-Soyuz Test Project are described. Included in the discussion of procedural aspects are methods and materials, in-flight microbial specimen collection, and preliminary analysis of microbial specimens. Medically important microorganisms recovered from both Apollo and Soyuz crewmen are evaluated.

Flow for Exercise Adherence: Testing an Intrinsic Model of Health Behavior

ERIC Educational Resources Information Center

Petosa, R. Lingyak; Holtz, Brian

2013-01-01

Background: Health behavior theory generally does not include intrinsic motivation as a determinate of health practices. Purpose: The purpose of this study was to test the flow theory of exercise adherence. Flow theory posits that exercise can be intrinsically rewarding if the experiences of self/time transcendence and control/mastery are achieved…

A Preliminary Assessment of Phase Separator Ground-Based and Reduced-Gravity Testing for ALS Systems

NASA Technical Reports Server (NTRS)

Hall, Nancy Rabel

2006-01-01

A viewgraph presentation of phase separator ground-based and reduced-gravity testing for Advanced Life Support (ALS) systems is shown. The topics include: 1) Multiphase Flow Technology Program; 2) Types of Separators; 3) MOBI Phase Separators; 4) Experiment set-up; and 5) Preliminary comparison/results.

Student Attitudes toward Nuclear Power Plants: A Classroom Experiment in the Field of Environmental Psychology.

ERIC Educational Resources Information Center

Spada, Hans; And Others

1977-01-01

As part of a senior high school physics unit on nuclear power, changes in student attitudes toward nuclear power plants and problems of energy supply were analyzed. Tests included a situational test, semantic differentials, knowledge or achievement, and a final questionnaire. The results are discussed. (CTM)

Grape Juice as an Attractant for Anastrepha suspensa (Diptera: Tephritidae) and Zaprionus indianus (Diptera: Drosophilidae)

USDA-ARS?s Scientific Manuscript database

In field tests conducted in south Florida to test grape juice as an alternative inexpensive bait for Anastrepha suspensa Loew, high numbers of Zaprionus indianus Gupta were captured in traps baited with aqueous grape juice. These experiments included comparisons of grape juice with standard A. susp...

Creativity: A Saleable Work Skill. Occupation Simulation Packet. Grades 3rd-4th.

ERIC Educational Resources Information Center

Dye, Dick

This teacher's guide for grades 3 and 4 contains simulated work experiences for students using the isolated skill concept - creativity. Teacher instructions include objectives, evaluation, and sequence of activities. The guide contains pre-tests and post-tests with instructions and answer keys. Two pre-skill activities are suggested, such as…

Apollo Block I Spacesuit Development and Apollo Block II Spacesuit Competition

NASA Technical Reports Server (NTRS)

McBarron, Jim

2013-01-01

Jim McBarron has over 40 years of experience with the U.S. Air Force pressure suit and NASA spacesuit development and operations. As a result of his experience, he shared his significant knowledge about the requirements and modifications made to the Gemini spacesuit, which were necessary to support the Apollo Block I Program. In addition, he provided an overview of the Apollo Block II Spacesuit competition test program conducted by the NASA Manned Spacecraft Center. Topics covered included the program's chronology; competition test program ground rules, scoring details, and final test results; and the implementation of resulting modifications to the Apollo Spacesuit Program. He concluded his presentation by identifying noteworthy lessons learned.

Micro-Satellite Impact Tests to Investigate Multi-Layer Insulation Fragments

NASA Astrophysics Data System (ADS)

Murakami, Junko; Hanada, Toshiya; Liou, J.-C.; Stansbery, Eugene

2009-03-01

This paper summarizes two satellite impact experiments completed in 2008. The objective of the experiments is to investigate the physical properties of satellite fragments, including those originated from Multi-Layer Insulation and a solar panel. One test generated approximately 1,800 fragments while the other produced only 1,000 fragments. This difference came from the number of needle-like fragments from carbon fiber reinforced plastics. All collected fragments were analyzed using the same method as described in the NASA standard breakup model and compared with the breakup model. This paper will present: (1) the area-to-mass ratio, size, and mass distributions of the fragments, and (2) the differences in fragment properties between the two tests.

Development of a PPT for the EO-1 Spacecraft

NASA Technical Reports Server (NTRS)

Benson, Scott W.; Arrington, Lynn A.; Hoskins, W. Andrew; Meckel, Nicole J.

2000-01-01

A Pulsed Plasma Thruster (PPT) has been developed for use in a technology demonstration flight experiment on the Earth Observing 1 (EO-1) New Millennium Program mission. The thruster replaces the spacecraft pitch axis momentum wheel for control and momentum management during an experiment of a minimum three-day duration. The EO-1 PPT configuration is a combination of new technology and design heritage from similar systems flown in the 1970's and 1980's. Acceptance testing of the protoflight unit has validated readiness for flight, and integration with the spacecraft, including initial combined testing, has been completed. The thruster provides a range of capability from 90 microN-sec impulse bit at 650 sec specific impulse for 12 W input power, through 860 microN-sec impulse bit at 1400 see specific impulse for 70 W input power. Development of this thruster reinitiates technology research and development and re-establishes an industry base for production of flight hardware. This paper reviews the EO-1 PPT development, including technology selection, design and fabrication, acceptance testing, and initial spacecraft integration and test.

A carcinogenic potency database of the standardized results of animal bioassays

PubMed Central

Gold, Lois Swirsky; Sawyer, Charles B.; Magaw, Renae; Backman, Georganne M.; De Veciana, Margarita; Levinson, Robert; Hooper, N. Kim; Havender, William R.; Bernstein, Leslie; Peto, Richard; Pike, Malcolm C.; Ames, Bruce N.

1984-01-01

The preceding paper described our numerical index of carcinogenic potency, the TD50 and the statistical procedures adopted for estimating it from experimental data. This paper presents the Carcinogenic Potency Database, which includes results of about 3000 long-term, chronic experiments of 770 test compounds. Part II is a discussion of the sources of our data, the rationale for the inclusion of particular experiments and particular target sites, and the conventions adopted in summarizing the literature. Part III is a guide to the plot of results presented in Part IV. A number of appendices are provided to facilitate use of the database. The plot includes information about chronic cancer tests in mammals, such as dose and other aspects of experimental protocol, histopathology and tumor incidence, TD50 and its statistical significance, dose response, author's opinion and literature reference. The plot readily permits comparisons of carcinogenic potency and many other aspects of cancer tests; it also provides quantitative information about negative tests. The range of carcinogenic potency is over 10 million-fold. PMID:6525996

Fiscal year 1976 progress report on a feasibility study evaluating the use of surface penetrators for planetary exploration

NASA Technical Reports Server (NTRS)

Blanchard, M. B.; Oberbeck, V. R.; Bunch, T. E.; Reynolds, R. T.; Canning, T. N.; Jackson, R. W.

1976-01-01

The feasibility of employing penetrators for exploring Mars was examined. Eight areas of interest for key scientific experiments were identified. These include: seismic activity, imaging, geochemistry, water measurement, heatflow, meteorology, magnetometry, and biochemistry. In seven of the eight potential experiment categories this year's progress included: conceptual design, instrument fabrication, instrument performance evaluation, and shock loading of important components. Most of the components survived deceleration testing with negligible performance changes. Components intended to be placed inside the penetrator forebody were tested up to 3,500 g and components intended to be placed on the afterbody were tested up to 21,000 g. A field test program was conducted using tentative Mars penetrator mission constraints. Drop tests were performed at two selected terrestrial analog sites to determine the range of penetration depths for anticipated common Martian materials. Minimum penetration occurred in basalt at Amboy, California. Three full-scale penetrators penetrated 0.4 to 0.9 m into the basalt after passing through 0.3 to 0.5 m of alluvial overburden. Maximum penetration occurred in unconsolidated sediments at McCook, Nebraska. Two full-scale penetrators penetrated 2.5 to 8.5 m of sediment. Impact occurred in two kinds of sediment: loess and layered clay. Deceleration g loads of nominally 2,000 for the forebody and 20,000 for the afterbody did not present serious design problems for potential experiments. Penetrators have successfully impacted into terrestrial analogs of the probable extremes of potential Martian sites.

Patient Perspectives on the Experience of Being Newly Diagnosed with HIV in the Emergency Department/Urgent Care Clinic of a Public Hospital

PubMed Central

Christopoulos, Katerina A.; Massey, Amina D.; Lopez, Andrea M.; Hare, C. Bradley; Johnson, Mallory O.; Pilcher, Christopher D.; Fielding, Hegla; Dawson-Rose, Carol

2013-01-01

We sought to understand patient perceptions of the emergency department/urgent care (ED/UC) HIV diagnosis experience as well as factors that may promote or discourage linkage to HIV care. We conducted in-depth interviews with patients (n=24) whose HIV infection was diagnosed in the ED/UC of a public hospital in San Francisco at least six months prior and who linked to HIV care at the hospital HIV clinic. Key diagnosis experience themes included physical discomfort and limited functionality, presence of comorbid diagnoses, a wide spectrum of HIV risk perception, and feelings of isolation and anxiety. Patients diagnosed with HIV in the ED/UC may not have their desired emotional supports with them, either because they are alone or they are with family members or friends to whom they do not want to immediately disclose. Other patients may have no one they can rely on for immediate support. Nearly all participants described compassionate disclosure of test results by ED/UC providers, although several noted logistical issues that complicated the disclosure experience. Key linkage to care themes included the importance of continuity between the testing site and HIV care, hospital admission as an opportunity for support and HIV education, and thoughtful matching by linkage staff to a primary care provider. ED/UC clinicians and testing programs should be sensitive to the unique roles of sickness, risk perception, and isolation in the ED/UC diagnosis experience, as these things may delay acceptance of HIV diagnosis. The disclosure and linkage to care experience is crucial in forming patient attitudes towards HIV and HIV care, thus staff involved in disclosure and linkage activities should be trained to deliver compassionate, informed, and thoughtful care that bridges HIV testing and treatment sites. PMID:23991214

Overview of the Exploration Exercise Device Validation Study Plans

NASA Technical Reports Server (NTRS)

DeWitt, J. K.; Swan, B. G.

2018-01-01

The NASA has determined that a multi-functional exercise device will be developed for use as an exercise device during exploration missions. The device will allow for full body resistance and metabolic exercise necessary to minimize physiological losses during space flight and to maintain fitness necessary to perform critical mission tasks. Prior to implementation as an exercise device on an Exploration vehicle, there will be verification and validation testing completed to determine device efficacy at providing the necessary training stimuli to achieve desired goals. Because the exploration device will be new device that has yet be specified, specific Verification and Validation (V&V) protocols have yet to be developed. Upon delivery of an exploration exercise device training unit, stakeholders throughout NASA will develop V&V plans that include ground-based testing and testing on the International Space Station (ISS). Stakeholders will develop test protocols that include success criterion for the device. Ground tests will occur at NASA Johnson Space Station prior to flight testing. The intents of the ground tests are to allow crew, spaceflight medicine, science, engineering, Astronaut Strength, Conditioning, and Reconditioning staff, and others to gain experience in the best utilization of the device. The goal is to obtain an evidence base for recommending use of the device on the ISS. The developed protocol will be created to achieve multiple objectives, including determining if the device provides an adequate training stimulus for 5th - 95th percentile males and females, allows for exercise modalities that protect functional capability, and is robust and can withstand extensive human use. Although protocols are yet to be determined, current expectations include use of the device by test subjects and current crew in order to obtain quantitative and qualitative feedback. Information obtained during the ground tests may be used to influence device modifications during design iterations. Assuming successful ground tests, the device will be installed on the ISS for testing during space flight. Spaceflight testing is envisioned to include an activation and checkout (ACO) phase and a V&V phase. During the ACO phase, 1-2 crewmembers will exercise with the device to ensure proper function. ACO is expected to last multiple months because of the many modes and methods of exercise that need to be assessed. However, the goal is to complete the ACO as quickly as possible. Once successful ACO occurs, the crew will be free to use the device for normal exercise pending concurrence from stakeholders. V&V tests on the ISS will ideally consist of crew using the device for all of their exercise for an entire mission. Exercise prescriptions will be supplied that replicate expected prescriptions during exploration missions. Crew that are not enrolled in the V&V studies would be also free to use the device as their schedule permits. As experience is gained by users, exercise protocols could change. The intent of all V&V testing is to ensure that all have thorough understanding of experience at optimizing device capability

Transient excitation and data processing techniques employing the fast fourier transform for aeroelastic testing

NASA Technical Reports Server (NTRS)

Jennings, W. P.; Olsen, N. L.; Walter, M. J.

1976-01-01

The development of testing techniques useful in airplane ground resonance testing, wind tunnel aeroelastic model testing, and airplane flight flutter testing is presented. Included is the consideration of impulsive excitation, steady-state sinusoidal excitation, and random and pseudorandom excitation. Reasons for the selection of fast sine sweeps for transient excitation are given. The use of the fast fourier transform dynamic analyzer (HP-5451B) is presented, together with a curve fitting data process in the Laplace domain to experimentally evaluate values of generalized mass, model frequencies, dampings, and mode shapes. The effects of poor signal to noise ratios due to turbulence creating data variance are discussed. Data manipulation techniques used to overcome variance problems are also included. The experience is described that was gained by using these techniques since the early stages of the SST program. Data measured during 747 flight flutter tests, and SST, YC-14, and 727 empennage flutter model tests are included.

Thermal Design and Analysis for the Cryogenic MIDAS Experiment

NASA Technical Reports Server (NTRS)

Amundsen, Ruth McElroy

1997-01-01

The Materials In Devices As Superconductors (MIDAS) spaceflight experiment is a NASA payload which launched in September 1996 on the Shuttle, and was transferred to the Mir Space Station for several months of operation. MIDAS was developed and built at NASA Langley Research Center (LaRC). The primary objective of the experiment was to determine the effects of microgravity and spaceflight on the electrical properties of high-temperature superconductive (HTS) materials. The thermal challenge on MIDAS was to maintain the superconductive specimens at or below 80 K for the entire operation of the experiment, including all ground testing and 90 days of spaceflight operation. Cooling was provided by a small tactical cryocooler. The superconductive specimens and the coldfinger of the cryocooler were mounted in a vacuum chamber, with vacuum levels maintained by an ion pump. The entire experiment was mounted for operation in a stowage locker inside Mir, with the only heat dissipation capability provided by a cooling fan exhausting to the habitable compartment. The thermal environment on Mir can potentially vary over the range 5 to 40 C; this was the range used in testing, and this wide range adds to the difficulty in managing the power dissipated from the experiment's active components. Many issues in the thermal design are discussed, including: thermal isolation methods for the cryogenic samples; design for cooling to cryogenic temperatures; cryogenic epoxy bonds; management of ambient temperature components self-heating; and fan cooling of the enclosed locker. Results of the design are also considered, including the thermal gradients across the HTS samples and cryogenic thermal strap, electronics and thermal sensor cryogenic performance, and differences between ground and flight performance. Modeling was performed in both SINDA-85 and MSC/PATRAN (with direct geometry import from the CAD design tool Pro/Engineer). Advantages of both types of models are discussed. Correlation of several models to ground testing and flight data (where available) is presented. Both SINDA and PATRAN models predicted the actual thermal performance of the experiment well, even without post-flight correlation adjustments of the models.

CONSTRUCTING AND DERIVING RECIPROCAL TRIGONOMETRIC RELATIONS: A FUNCTIONAL ANALYTIC APPROACH

PubMed Central

Ninness, Chris; Dixon, Mark; Barnes-Holmes, Dermot; Rehfeldt, Ruth Anne; Rumph, Robin; McCuller, Glen; Holland, James; Smith, Ronald; Ninness, Sharon K; McGinty, Jennifer

2009-01-01

Participants were pretrained and tested on mutually entailed trigonometric relations and combinatorially entailed relations as they pertained to positive and negative forms of sine, cosine, secant, and cosecant. Experiment 1 focused on training and testing transformations of these mathematical functions in terms of amplitude and frequency followed by tests of novel relations. Experiment 2 addressed training in accordance with frames of coordination (same as) and frames of opposition (reciprocal of) followed by more tests of novel relations. All assessments of derived and novel formula-to-graph relations, including reciprocal functions with diversified amplitude and frequency transformations, indicated that all 4 participants demonstrated substantial improvement in their ability to identify increasingly complex trigonometric formula-to-graph relations pertaining to same as and reciprocal of to establish mathematically complex repertoires. PMID:19949509

Constructing and deriving reciprocal trigonometric relations: a functional analytic approach.

PubMed

Ninness, Chris; Dixon, Mark; Barnes-Holmes, Dermot; Rehfeldt, Ruth Anne; Rumph, Robin; McCuller, Glen; Holland, James; Smith, Ronald; Ninness, Sharon K; McGinty, Jennifer

2009-01-01

Participants were pretrained and tested on mutually entailed trigonometric relations and combinatorially entailed relations as they pertained to positive and negative forms of sine, cosine, secant, and cosecant. Experiment 1 focused on training and testing transformations of these mathematical functions in terms of amplitude and frequency followed by tests of novel relations. Experiment 2 addressed training in accordance with frames of coordination (same as) and frames of opposition (reciprocal of) followed by more tests of novel relations. All assessments of derived and novel formula-to-graph relations, including reciprocal functions with diversified amplitude and frequency transformations, indicated that all 4 participants demonstrated substantial improvement in their ability to identify increasingly complex trigonometric formula-to-graph relations pertaining to same as and reciprocal of to establish mathematically complex repertoires.

Ongoing research experiments at the former Soviet nuclear test site in eastern Kazakhstan

USGS Publications Warehouse

Leith, William S.; Kluchko, Luke J.; Konovalov, Vladimir; Vouille, Gerard

2002-01-01

Degelen mountain, located in EasternKazakhstan near the city of Semipalatinsk, was once the Soviets most active underground nuclear test site. Two hundred fifteen nuclear tests were conducted in 181 tunnels driven horizontally into its many ridges--almost twice the number of tests as at any other Soviet underground nuclear test site. It was also the site of the first Soviet underground nuclear test--a 1-kiloton device detonated on October 11, 1961. Until recently, the details of testing at Degelen were kept secret and have been the subject of considerable speculation. However, in 1991, the Semipalatinsk test site became part of the newly independent Republic of Kazakhstan; and in 1995, the Kazakhstani government concluded an agreement with the U.S. Department of Defense to eliminate the nuclear testing infrastructure in Kazakhstan. This agreement, which calls for the "demilitarization of the infrastructure directly associated with the nuclear weapons test tunnels," has been implemented as the "Degelen Mountain Tunnel Closure Program." The U.S. Defense Threat Reduction Agency, in partnership with the Department of Energy, has permitted the use of the tunnel closure project at the former nuclear test site as a foundation on which to support cost-effective, research-and-development-funded experiments. These experiments are principally designed to improve U.S. capabilities to monitor and verify the Comprehensive Test Ban Treaty (CTBT), but have provided a new source of information on the effects of nuclear and chemical explosions on hard, fractured rock environments. These new data extends and confirms the results of recent Russian publications on the rock environment at the site and the mechanical effects of large-scale chemical and nuclear testing. In 1998, a large-scale tunnel closure experiment, Omega-1, was conducted in Tunnel 214 at Degelen mountain. In this experiment, a 100-ton chemical explosive blast was used to test technologies for monitoring the Comprehensive Nuclear Test Ban Treaty, and to calibrate a portion of the CTBT's International Monitoring System. This experiment has also provided important benchmark data on the mechanical behavior of hard, dense, fractured rock, and has demonstrated the feasibility of fielding large-scale calibration explosions, which are specified as a "confidence-building measure" in the CTBT Protocol. Two other large-scale explosion experiments, Omega-2 and Omega-3, are planned for the summer of 1999 and 2000. Like the Tunnel 214 test, the 1999 experiment will include close-in monitoring of near-source effects, as well as contributing to the calibration of key seismic stations for the Comprehensive Test Ban Treaty. The Omega-3 test will examine the effect of multiple blasts on the fractured rock environment.

Remote Sensing Image Quality Assessment Experiment with Post-Processing

NASA Astrophysics Data System (ADS)

Jiang, W.; Chen, S.; Wang, X.; Huang, Q.; Shi, H.; Man, Y.

2018-04-01

This paper briefly describes the post-processing influence assessment experiment, the experiment includes three steps: the physical simulation, image processing, and image quality assessment. The physical simulation models sampled imaging system in laboratory, the imaging system parameters are tested, the digital image serving as image processing input are produced by this imaging system with the same imaging system parameters. The gathered optical sampled images with the tested imaging parameters are processed by 3 digital image processes, including calibration pre-processing, lossy compression with different compression ratio and image post-processing with different core. Image quality assessment method used is just noticeable difference (JND) subject assessment based on ISO20462, through subject assessment of the gathered and processing images, the influence of different imaging parameters and post-processing to image quality can be found. The six JND subject assessment experimental data can be validated each other. Main conclusions include: image post-processing can improve image quality; image post-processing can improve image quality even with lossy compression, image quality with higher compression ratio improves less than lower ratio; with our image post-processing method, image quality is better, when camera MTF being within a small range.

Development of an Antimicrobial Susceptibility Testing Method Suitable for Performing During Space Flight

NASA Technical Reports Server (NTRS)

Jorgensen, James H.; Skweres, Joyce A.; Mishra S. K.; McElmeel, M. Letticia; Maher, Louise A.; Mulder, Ross; Lancaster, Michael V.; Pierson, Duane L.

1997-01-01

Very little is known regarding the affects of the microgravity environment of space flight upon the action of antimicrobial agents on bacterial pathogens. This study was undertaken to develop a simple method for conducting antibacterial susceptibility tests during a Space Shuttle mission. Specially prepared susceptibility test research cards (bioMerieux Vitek, Hazelwood, MO) were designed to include 6-11 serial two-fold dilutions of 14 antimicrobial agents, including penicillins, cephalosporins, a Beta-lactamase inhibitor, vancomycin, erythromycin, tetracycline, gentamicin, ciprofloxacin, and trimethoprim/sulfamethoxazole. Minimal inhibitory concentrations (MICS) of the drugs were determined by visual reading of color endpoints in the Vitek research cards made possible by incorporation of a colorimetric growth indicator (alamarBlue(Trademark), Accumed International, Westlake, OH). This study has demonstrated reproducible susceptibility results when testing isolates of Staphylococcus aurezis, Group A Streptococcus, Enterococcusfaecalis, Escherichia coli (beta-lactamase positive and negative strains), Klebsiella pneumoniae, Enterobacter cloacae, and Pseudomoiias aeruginosa. In some instances, the MICs were comparable to those determined using a standard broth microdilution method, while in some cases the unique test media and format yielded slightly different values, that were themselves reproducible. The proposed in-flight experiment will include inoculation of the Vitek cards on the ground prior to launch of the Space Shuttle, storage of inoculated cards at refrigeration temperature aboard the Space Shuttle until experiment initiation, then incubation of the cards for 18-48 h prior to visual interpretation of MICs by the mission's astronauts. Ground-based studies have shown reproducible MICs following storage of inoculated cards for 7 days at 4-8 C to accommodate the mission's time schedule and the astronauts' activities. For comparison, ground-based control (normal gravity) MIC values will be generated by simultaneous inoculation and incubation of a second set of test cards in a laboratory at the launch site. This procedure can provide a safe and compact experiment that should yield new information on the affects of microgravity on the biological activities of various classes of antibiotics.

Experimental program for real gas flow code validation at NASA Ames Research Center

NASA Technical Reports Server (NTRS)

Deiwert, George S.; Strawa, Anthony W.; Sharma, Surendra P.; Park, Chul

1989-01-01

The experimental program for validating real gas hypersonic flow codes at NASA Ames Rsearch Center is described. Ground-based test facilities used include ballistic ranges, shock tubes and shock tunnels, arc jet facilities and heated-air hypersonic wind tunnels. Also included are large-scale computer systems for kinetic theory simulations and benchmark code solutions. Flight tests consist of the Aeroassist Flight Experiment, the Space Shuttle, Project Fire 2, and planetary probes such as Galileo, Pioneer Venus, and PAET.

Applicability of Aerospace Materials Ground Flammability Test Data to Spacecraft Environments Theory and Applied Technologies

NASA Technical Reports Server (NTRS)

Hirsch, David; Williams, Jim; Beeson, Harold

2009-01-01

This slide presentation reviews the use of ground test data in reference to flammability to spacecraft environments. It reviews the current approach to spacecraft fire safety, the challenges to fire safety that the Constellation program poses, the current trends in the evaluation of the Constellation materials flammability, and the correlation of test data from ground flammability tests with the spacecraft environment. Included is a proposal for testing and the design of experiments to test the flammability of materials under similar spacecraft conditions.

Accelerated testing of module-level power electronics for long-term reliability

DOE Office of Scientific and Technical Information (OSTI.GOV)

Flicker, Jack David; Tamizhmani, Govindasamy; Moorthy, Mathan Kumar

This work has applied a suite of long-term-reliability accelerated tests to a variety of module-level power electronics (MLPE) devices (such as microinverters and optimizers) from five different manufacturers. This dataset is one of the first (only the paper by Parker et al. entitled “Dominant factors affecting reliability of alternating current photovoltaic modules,” in Proc. 42nd IEEE Photovoltaic Spec. Conf., 2015, is reported for reliability testing in the literature), as well as the largest, experimental sets in public literature, both in the sample size (five manufacturers including both dc/dc and dc/ac units and 20 units for each test) and the numbermore » of experiments (six different experimental test conditions) for MLPE devices. The accelerated stress tests (thermal cycling test per IEC 61215 profile, damp heat test per IEC 61215 profile, and static temperature tests at 100 and 125 °C) were performed under powered and unpowered conditions. The first independent long-term experimental data regarding damp heat and grid transient testing, as well as the longest term (>9 month) testing of MLPE units reported in the literature for thermal cycling and high-temperature operating life, are included in these experiments. Additionally, this work is the first to show in situ power measurements, as well as periodic efficiency measurements over a series of experimental tests, demonstrating whether certain tests result in long-term degradation or immediate catastrophic failures. Lastly, the result of this testing highlights the performance of MLPE units under the application of several accelerated environmental stressors.« less

Accelerated testing of module-level power electronics for long-term reliability

DOE PAGES

Flicker, Jack David; Tamizhmani, Govindasamy; Moorthy, Mathan Kumar; ...

2016-11-10

This work has applied a suite of long-term-reliability accelerated tests to a variety of module-level power electronics (MLPE) devices (such as microinverters and optimizers) from five different manufacturers. This dataset is one of the first (only the paper by Parker et al. entitled “Dominant factors affecting reliability of alternating current photovoltaic modules,” in Proc. 42nd IEEE Photovoltaic Spec. Conf., 2015, is reported for reliability testing in the literature), as well as the largest, experimental sets in public literature, both in the sample size (five manufacturers including both dc/dc and dc/ac units and 20 units for each test) and the numbermore » of experiments (six different experimental test conditions) for MLPE devices. The accelerated stress tests (thermal cycling test per IEC 61215 profile, damp heat test per IEC 61215 profile, and static temperature tests at 100 and 125 °C) were performed under powered and unpowered conditions. The first independent long-term experimental data regarding damp heat and grid transient testing, as well as the longest term (>9 month) testing of MLPE units reported in the literature for thermal cycling and high-temperature operating life, are included in these experiments. Additionally, this work is the first to show in situ power measurements, as well as periodic efficiency measurements over a series of experimental tests, demonstrating whether certain tests result in long-term degradation or immediate catastrophic failures. Lastly, the result of this testing highlights the performance of MLPE units under the application of several accelerated environmental stressors.« less

Antenna Technology Shuttle Experiment (ATSE)

NASA Technical Reports Server (NTRS)

Freeland, R. E.; Mettler, E.; Miller, L. J.; Rahmet-Samii, Y.; Weber, W. J., III

1987-01-01

Numerous space applications of the future will require mesh deployable antennas of 15 m in diameter or greater for frequencies up to 20 GHz. These applications include mobile communications satellites, orbiting very long baseline interferometry (VLBI) astrophysics missions, and Earth remote sensing missions. A Lockheed wrap rip antennas was used as the test article. The experiments covered a broad range of structural, control, and RF discipline objectives, which is fulfilled in total, would greatly reduce the risk of employing these antenna systems in future space applications. It was concluded that a flight experiment of a relatively large mesh deployable reflector is achievable with no major technological or cost drivers. The test articles and the instrumentation are all within the state of the art and in most cases rely on proven flight hardware. Every effort was made to design the experiments for low cost.

Examination of a Junction-Box Adhesion Test for Use in Photovoltaic Module Qualification: Preprint

DOE Office of Scientific and Technical Information (OSTI.GOV)

Miller, D. C.; Wohlgemuth, J. H.

2012-08-01

Engineering robust adhesion of the junction-box (j-box) is a hurdle typically encountered by photovoltaic (PV) module manufacturers during product development. There are historical incidences of adverse effects (e.g., fires) caused when the j-box/adhesive/module system has failed in the field. The addition of a weight to the j-box during the 'damp heat' IEC qualification test is proposed to verify the basic robustness of its adhesion system. The details of the proposed test will be described, in addition to the preliminary results obtained using representative materials and components. The described discovery experiments examine moisture-cured silicone, foam tape, and hot-melt adhesives used inmore » conjunction with PET or glass module 'substrates.' To be able to interpret the results, a set of material-level characterizations was performed, including thermogravimetric analysis, differential scanning calorimetry, and dynamic mechanical analysis. PV j-boxes were adhered to a substrate, loaded with a prescribed weight, and then placed inside an environmental chamber (at 85C, 85% relative humidity). Some systems did not remain attached through the discovery experiments. Observed failure modes include delamination (at the j-box/adhesive or adhesive/substrate interface) and phase change/creep. The results are discussed in the context of the application requirements, in addition to the plan for the formal experiment supporting the proposed modification to the qualification test.« less

Development of a MEMS device for acoustic emission testing

NASA Astrophysics Data System (ADS)

Ozevin, Didem; Pessiki, Stephen P.; Jain, Akash; Greve, David W.; Oppenheim, Irving J.

2003-08-01

Acoustic emission testing is an important technology for evaluating structural materials, and especially for detecting damage in structural members. Significant new capabilities may be gained by developing MEMS transducers for acoustic emission testing, including permanent bonding or embedment for superior coupling, greater density of transducer placement, and a bundle of transducers on each device tuned to different frequencies. Additional advantages include capabilities for maintenance of signal histories and coordination between multiple transducers. We designed a MEMS device for acoustic emission testing that features two different mechanical types, a hexagonal plate design and a spring-mass design, with multiple detectors of each type at ten different frequencies in the range of 100 kHz to 1 MHz. The devices were fabricated in the multi-user polysilicon surface micromachining (MUMPs) process and we have conducted electrical characterization experiments and initial experiments on acoustic emission detection. We first report on C(V) measurements and perform a comparison between predicted (design) and measured response. We next report on admittance measurements conducted at pressures varying from vacuum to atmospheric, identifying the resonant frequencies and again providing a comparison with predicted performance. We then describe initial calibration experiments that compare the performance of the detectors to other acoustic emission transducers, and we discuss the overall performance of the device as a sensor suite, as contrasted to the single-channel performance of most commercial transducers.

Essay: Robert H. Siemann As Leader of the Advanced Accelerator Research Department

DOE Office of Scientific and Technical Information (OSTI.GOV)

Colby, Eric R.; Hogan, Mark J.; /SLAC

Robert H. Siemann originally conceived of the Advanced Accelerator Research Department (AARD) as an academic, experimental group dedicated to probing the technical limitations of accelerators while providing excellent educational opportunities for young scientists. The early years of the Accelerator Research Department B, as it was then known, were dedicated to a wealth of mostly student-led experiments to examine the promise of advanced accelerator techniques. High-gradient techniques including millimeter-wave rf acceleration, beam-driven plasma acceleration, and direct laser acceleration were pursued, including tests of materials under rf pulsed heating and short-pulse laser radiation, to establish the ultimate limitations on gradient. As themore » department and program grew, so did the motivation to found an accelerator research center that brought experimentalists together in a test facility environment to conduct a broad range of experiments. The Final Focus Test Beam and later the Next Linear Collider Test Accelerator provided unique experimental facilities for AARD staff and collaborators to carry out advanced accelerator experiments. Throughout the evolution of this dynamic program, Bob maintained a department atmosphere and culture more reminiscent of a university research group than a national laboratory department. His exceptional ability to balance multiple roles as scientist, professor, and administrator enabled the creation and preservation of an environment that fostered technical innovation and scholarship.« less

Development of a Shipboard Remote Control and Telemetry Experimental System for Large-Scale Model’s Motions and Loads Measurement in Realistic Sea Waves

PubMed Central

Jiao, Jialong; Ren, Huilong; Adenya, Christiaan Adika; Chen, Chaohe

2017-01-01

Wave-induced motion and load responses are important criteria for ship performance evaluation. Physical experiments have long been an indispensable tool in the predictions of ship’s navigation state, speed, motions, accelerations, sectional loads and wave impact pressure. Currently, majority of the experiments are conducted in laboratory tank environment, where the wave environments are different from the realistic sea waves. In this paper, a laboratory tank testing system for ship motions and loads measurement is reviewed and reported first. Then, a novel large-scale model measurement technique is developed based on the laboratory testing foundations to obtain accurate motion and load responses of ships in realistic sea conditions. For this purpose, a suite of advanced remote control and telemetry experimental system was developed in-house to allow for the implementation of large-scale model seakeeping measurement at sea. The experimental system includes a series of technique sensors, e.g., the Global Position System/Inertial Navigation System (GPS/INS) module, course top, optical fiber sensors, strain gauges, pressure sensors and accelerometers. The developed measurement system was tested by field experiments in coastal seas, which indicates that the proposed large-scale model testing scheme is capable and feasible. Meaningful data including ocean environment parameters, ship navigation state, motions and loads were obtained through the sea trial campaign. PMID:29109379

Failure of the Porcine Ascending Aorta: Multidirectional Experiments and a Unifying Microstructural Model

PubMed Central

Witzenburg, Colleen M.; Dhume, Rohit Y.; Shah, Sachin B.; Korenczuk, Christopher E.; Wagner, Hallie P.; Alford, Patrick W.; Barocas, Victor H.

2017-01-01

The ascending thoracic aorta is poorly understood mechanically, especially its risk of dissection. To make better predictions of dissection risk, more information about the multidimensional failure behavior of the tissue is needed, and this information must be incorporated into an appropriate theoretical/computational model. Toward the creation of such a model, uniaxial, equibiaxial, peel, and shear lap tests were performed on healthy porcine ascending aorta samples. Uniaxial and equibiaxial tests showed anisotropy with greater stiffness and strength in the circumferential direction. Shear lap tests showed catastrophic failure at shear stresses (150–200 kPa) much lower than uniaxial tests (750–2500 kPa), consistent with the low peel tension (∼60 mN/mm). A novel multiscale computational model, including both prefailure and failure mechanics of the aorta, was developed. The microstructural part of the model included contributions from a collagen-reinforced elastin sheet and interlamellar connections representing fibrillin and smooth muscle. Components were represented as nonlinear fibers that failed at a critical stretch. Multiscale simulations of the different experiments were performed, and the model, appropriately specified, agreed well with all experimental data, representing a uniquely complete structure-based description of aorta mechanics. In addition, our experiments and model demonstrate the very low strength of the aorta in radial shear, suggesting an important possible mechanism for aortic dissection. PMID:27893044

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rutqvist, Jonny; Blanco Martin, Laura; Mukhopadhyay, Sumit

The modeling efforts in support of the field test planning conducted at LBNL leverage on recent developments of tools for modeling coupled thermal-hydrological-mechanical-chemical (THMC) processes in salt and their effect on brine migration at high temperatures. This work includes development related to, and implementation of, essential capabilities, as well as testing the model against relevant information and published experimental data related to the fate and transport of water. These are modeling capabilities that will be suitable for assisting in the design of field experiment, especially related to multiphase flow processes coupled with mechanical deformations, at high temperature. In this report,more » we first examine previous generic repository modeling results, focusing on the first 20 years to investigate the expected evolution of the different processes that could be monitored in a full-scale heater experiment, and then present new results from ongoing modeling of the Thermal Simulation for Drift Emplacement (TSDE) experiment, a heater experiment on the in-drift emplacement concept at the Asse Mine, Germany, and provide an update on the ongoing model developments for modeling brine migration. LBNL also supported field test planning activities via contributions to and technical review of framework documents and test plans, as well as participation in workshops associated with field test planning.« less

Post flight system analysis of FRECOPA (AO 138)

NASA Technical Reports Server (NTRS)

Durin, Christian

1991-01-01

The unexpected duration for the flight of the Long Duration Exposure Facility (LDEF) conducted CNES to create a special investigation group in order to analyze all the materials and systems which compose the French Cooperative Payload (FRECOPA) except the experiments especially prepared for the flight. The FRECOPA tray was on the trailing face (V-) of the LDEF and protected from the atomic oxygen flux during all the flight. However, the solar irradiation was very important with solar flux quite perpendicular to the experiment once an orbit. There was also a good vacuum environment. The objectives are to test the effects of the combined space environment on materials and components like: structure, thermal control coatings and blankets, electronic unit, motors, and mechanical fixtures. When the LDEF returned to Kennedy Space Center, a visual inspection showed the very good behavior of the materials used and it was noted that the three mechanisms to open and close the experiment canisters worked completely. Many impacts of micrometeoroids or space debris on the structure and on the thermal protections were observed. After FRECOPA was brought back to Toulouse, many tests were performed and include: working order tests, mechanical tests (tension), optical and electronic microscopy (SEM), surface analysis (ESCA, SIMS, RBS, AUGER, etc.), thermal analysis, pressure measurements, and gas analysis (outgassing tests). The results of these experiments are discussed.

A teaching intervention for reading laboratory experiments in college-level introductory chemistry

NASA Astrophysics Data System (ADS)

Kirk, Maria Kristine

The purpose of this study was to determine the effects that a pre-laboratory guide, conceptualized as a "scientific story grammar," has on college chemistry students' learning when they read an introductory chemistry laboratory manual and perform the experiments in the chemistry laboratory. The participants (N = 56) were students enrolled in four existing general chemistry laboratory sections taught by two instructors at a women's liberal arts college. The pre-laboratory guide consisted of eight questions about the experiment, including the purpose, chemical species, variables, chemical method, procedure, and hypothesis. The effects of the intervention were compared with those of the traditional pre-laboratory assignment for the eight chemistry experiments. Measures included quizzes, tests, chemistry achievement test, science process skills test, laboratory reports, laboratory average, and semester grade. The covariates were mathematical aptitude and prior knowledge of chemistry and science processes, on which the groups differed significantly. The study captured students' perceptions of their experience in general chemistry through a survey and interviews with eight students. The only significant differences in the treatment group's performance were in some subscores on lecture items and laboratory items on the quizzes. An apparent induction period was noted, in that significant measures occurred in mid-semester. Voluntary study with the pre-laboratory guide by control students precluded significant differences on measures given later in the semester. The groups' responses to the survey were similar. Significant instructor effects on three survey items were corroborated by the interviews. The researcher's students were more positive about their pre-laboratory tasks, enjoyed the laboratory sessions more, and were more confident about doing chemistry experiments than the laboratory instructor's groups due to differences in scaffolding by the instructors.

Status of the irradiation test vehicle for testing fusion materials in the Advanced Test Reactor

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tsai, H.; Gomes, I.C.; Smith, D.L.

1998-09-01

The design of the irradiation test vehicle (ITV) for the Advanced Test Reactor (ATR) has been completed. The main application for the ITV is irradiation testing of candidate fusion structural materials, including vanadium-base alloys, silicon carbide composites, and low-activation steels. Construction of the vehicle is underway at the Lockheed Martin Idaho Technology Company (LMITCO). Dummy test trains are being built for system checkout and fine-tuning. Reactor insertion of the ITV with the dummy test trains is scheduled for fall 1998. Barring unexpected difficulties, the ITV will be available for experiments in early 1999.

Gravitation theory - Empirical status from solar system experiments.

NASA Technical Reports Server (NTRS)

Nordtvedt, K. L., Jr.

1972-01-01

Review of historical and recent experiments which speak in favor of a post-Newtonian relativistic gravitational theory. The topics include the foundational experiments, metric theories of gravity, experiments designed to differentiate among the metric theories, and tests of Machian concepts of gravity. It is shown that the metric field for any metric theory can be specified by a series of potential terms with several parameters. It is pointed out that empirical results available up to date yield values of the parameters which are consistent with the prediction of Einstein's general relativity.

Spontaneously Generating Life in Your Classroom? Pasteur, Spallanzani and Science Process.

ERIC Educational Resources Information Center

Byington, Scott

2001-01-01

Presents an experiment that tests for spontaneous generation, or abiogenesis. Observes microbial growth in nutrient broth under seven different flask environments. Includes instructions for the methods. (YDS)

Comparison of experiment with calculations using curvature-corrected zero and two equation turbulence models for a two-dimensional U-duct

NASA Astrophysics Data System (ADS)

Monson, D. J.; Seegmiller, H. L.; McConnaughey, P. K.

1990-06-01

In this paper experimental measurements are compared with Navier-Stokes calculations using seven different turbulence models for the internal flow in a two-dimensional U-duct. The configuration is representative of many internal flows of engineering interst that experience strong curvature. In an effort to improve agreement, this paper tests several versions of the two-equation k-epsilon turbulence model including the standard version, an extended version with a production range time scale, and a version that includes curvature time scales. Each is tested in its high and low Reynolds number formulations. Calculations using these new models and the original mixing length model are compared here with measurements of mean and turbulence velocities, static pressure and skin friction in the U-duct at two Reynolds numbers. The comparisons show that only the low Reynolds number version of the extended k-epsilon model does a reasonable job of predicting the important features of this flow at both Reynolds numbers tested.

Mathematical anxiety is linked to reduced cognitive reflection: a potential road from discomfort in the mathematics classroom to susceptibility to biases.

PubMed

Morsanyi, Kinga; Busdraghi, Chiara; Primi, Caterina

2014-09-01

When asked to solve mathematical problems, some people experience anxiety and threat, which can lead to impaired mathematical performance (Curr Dir Psychol Sci 11:181-185, 2002). The present studies investigated the link between mathematical anxiety and performance on the cognitive reflection test (CRT; J Econ Perspect 19:25-42, 2005). The CRT is a measure of a person's ability to resist intuitive response tendencies, and it correlates strongly with important real-life outcomes, such as time preferences, risk-taking, and rational thinking. In Experiments 1 and 2 the relationships between maths anxiety, mathematical knowledge/mathematical achievement, test anxiety and cognitive reflection were analysed using mediation analyses. Experiment 3 included a manipulation of working memory load. The effects of anxiety and working memory load were analysed using ANOVAs. Our experiments with university students (Experiments 1 and 3) and secondary school students (Experiment 2) demonstrated that mathematical anxiety was a significant predictor of cognitive reflection, even after controlling for the effects of general mathematical knowledge (in Experiment 1), school mathematical achievement (in Experiment 2) and test anxiety (in Experiments 1-3). Furthermore, Experiment 3 showed that mathematical anxiety and burdening working memory resources with a secondary task had similar effects on cognitive reflection. Given earlier findings that showed a close link between cognitive reflection, unbiased decisions and rationality, our results suggest that mathematical anxiety might be negatively related to individuals' ability to make advantageous choices and good decisions.

Submission of FeCrAl Feedstock for Support of AFC ATR-2 Irradiations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Field, Kevin G.; Barrett, Kristine E.; Sun, Zhiqian

The Advanced Test Reactor (ATR) is currently being used to test accident tolerant fuel (ATF) forms destined for commercial nuclear power plant deployment. One irradiation program using the ATR for ATF concepts, Accident Tolerant Fuel-2 (ATF-2), is a water loop irradiation test using miniaturized fuel pins as test articles. This complicated testing configuration requires a series of pre-test experiments and verification including a flowing loop autoclave test and a sensor qualification test (SQT) prior to full test train deployment within the ATR. In support of the ATF-2 irradiation program, Oak Ridge National Laboratory (ORNL) has supplied two different Generation IImore » FeCrAl alloys in rod stock form to Idaho National Laboratory (INL). These rods will be machined into dummy pins for deployment in the autoclave test and SQT. Post-test analysis of the dummy pins will provide initial insight into the performance of Generation II FeCrAl alloys in the ATF-2 irradiation experiment as well as within a commercial nuclear reactor.« less

Potential pressurized payloads: Fluid and thermal experiments

NASA Technical Reports Server (NTRS)

Swanson, Theodore D.

1992-01-01

Space Station Freedom (SSF) presents the opportunity to perform long term fluid and thermal experiments in a microgravity environment. This presentation provides perspective on the need for fluids/thermal experimentation in a microgravity environment, addresses previous efforts, identifies possible experiments, and discusses the capabilities of a proposed fluid physics/dynamics test facility. Numerous spacecraft systems use fluids for their operation. Thermal control, propulsion, waste management, and various operational processes are examples of such systems. However, effective ground testing is very difficult. This is because the effect of gravity induced phenomena, such as hydrostatic pressure, buoyant convection, and stratification, overcome such forces as surface tension, diffusion, electric potential, etc., which normally dominate in a microgravity environment. Hence, space experimentation is necessary to develop and validate a new fluid based technology. Two broad types of experiments may be performed on SSF: basic research and applied research. Basic research might include experiments focusing on capillary phenomena (with or without thermal and/or solutal gradients), thermal/solutal convection, phase transitions, and multiphase flow. Representative examples of applied research might include two-phase pressure drop, two-phase flow instabilities, heat transfer coefficients, fluid tank fill/drain, tank slosh dynamics, condensate removal enhancement, and void formation within thermal energy storage materials. In order to better support such fluid/thermal experiments on board SSF, OSSA has developed a conceptual design for a proposed Fluid Physics/Dynamics Facility (FP/DF). The proposed facility consists of one facility rack permanently located on SSF and one experimenter rack which is changed out as needed to support specific experiments. This approach will minimize the on-board integration/deintegration required for specific experiments. The FP/DF will have acceleration/vibration compensation, power and thermal interfaces, computer command/data collection, a video imaging system, and a portable glove box for operations. This facility will allow real-time astronaut interaction with the testing.

Enhancement of Spatial Ability in Girls in a Single-Sex Environment through Spatial Experience and the Impact on Information Seeking

ERIC Educational Resources Information Center

Swarlis, Linda L.

2008-01-01

The test scores of spatial ability for women lag behind those of men in many spatial tests. On the Mental Rotations Test (MRT), a significant gender gap has existed for over 20 years and continues to exist. High spatial ability has been linked to efficiencies in typical computing tasks including Web and database searching, text editing, and…

Diagnostic accuracy of different caries risk assessment methods. A systematic review.

PubMed

Senneby, Anna; Mejàre, Ingegerd; Sahlin, Nils-Eric; Svensäter, Gunnel; Rohlin, Madeleine

2015-12-01

To evaluate the accuracy of different methods used to identify individuals with increased risk of developing dental coronal caries. Studies on following methods were included: previous caries experience, tests using microbiota, buffering capacity, salivary flow rate, oral hygiene, dietary habits and sociodemographic variables. QUADAS-2 was used to assess risk of bias. Sensitivity, specificity, predictive values, and likelihood ratios (LR) were calculated. Quality of evidence based on ≥3 studies of a method was rated according to GRADE. PubMed, Cochrane Library, Web of Science and reference lists of included publications were searched up to January 2015. From 5776 identified articles, 18 were included. Assessment of study quality identified methodological limitations concerning study design, test technology and reporting. No study presented low risk of bias in all domains. Three or more studies were found only for previous caries experience and salivary mutans streptococci and quality of evidence for these methods was low. Evidence regarding other methods was lacking. For previous caries experience, sensitivity ranged between 0.21 and 0.94 and specificity between 0.20 and 1. Tests using salivary mutans streptococci resulted in low sensitivity and high specificity. For children with primary teeth at baseline, pooled LR for a positive test was 3 for previous caries experience and 4 for salivary mutans streptococci, given a threshold ≥10(5) CFU/ml. Evidence on the validity of analysed methods used for caries risk assessment is limited. As methodological quality was low, there is a need to improve study design. Low validity for the analysed methods may lead to patients with increased risk not being identified, whereas some are falsely identified as being at risk. As caries risk assessment guides individualized decisions on interventions and intervals for patient recall, improved performance based on best evidence is greatly needed. Copyright © 2015 Elsevier Ltd. All rights reserved.

Experience, knowledge, and opinions about childhood genetic testing in Batten disease.

PubMed

Adams, Heather R; Rose, Katherine; Augustine, Erika F; Kwon, Jennifer M; deBlieck, Elisabeth A; Marshall, Frederick J; Vierhile, Amy; Mink, Jonathan W; Nance, Martha A

2014-02-01

Policies for genetic testing in children (GTIC) focus on medical or psychosocial benefit to the child, discouraging or prohibiting carrier testing, and advising caution regarding pre-symptomatic diagnosis if no treatment exists. This study sought to understand parents' perspectives on these issues and determine their experiences and knowledge related to genetic testing for Batten disease - a set of inherited neurodegenerative diseases of childhood onset for which no disease modifying therapies yet exist. Parents of children with Batten disease completed a survey of their knowledge of genetics, experience with genetic testing, and opinions regarding GTIC. 54% had sought genetic testing for non-affected family members, including predictive diagnosis of healthy, at-risk children. Participation in any genetic counseling was associated with greater knowledge on questions about genetics. The majority of parents felt it was better to know ahead of time that a child would develop Batten disease, believed that this knowledge would not alter how they related to their child, and that parents should have the final say in deciding whether to obtain GTIC. Parents of children with an inherited disease are knowledgeable about genetics and wish to establish predictive or carrier status of at-risk children. Copyright © 2013 Elsevier Inc. All rights reserved.

Statistic analyses of the color experience according to the age of the observer.

PubMed

Hunjet, Anica; Parac-Osterman, Durdica; Vucaj, Edita

2013-04-01

Psychological experience of color is a real state of the communication between the environment and color, and it will depend on the source of the light, angle of the view, and particular on the observer and his health condition. Hering's theory or a theory of the opponent processes supposes that cones, which are situated in the retina of the eye, are not sensible on the three chromatic domains (areas, fields, zones) (red, green and purple-blue), but they produce a signal based on the principle of the opposed pairs of colors. A reason of this theory depends on the fact that certain disorders of the color eyesight, which include blindness to certain colors, cause blindness to pairs of opponent colors. This paper presents a demonstration of the experience of blue and yellow tone according to the age of the observer. For the testing of the statistically significant differences in the omission in the color experience according to the color of the background we use following statistical tests: Mann-Whitnney U Test, Kruskal-Wallis ANOVA and Median test. It was proven that the differences are statistically significant in the elderly persons (older than 35 years).

Space processing applications rocket project. SPAR 8

NASA Technical Reports Server (NTRS)

Chassay, R. P. (Editor)

1984-01-01

The Space Processing Applications Rocket Project (SPAR) VIII Final Report contains the engineering report prepared at the Marshall Space Flight Center (MSFC) as well as the three reports from the principal investigators. These reports also describe pertinent portions of ground-based research leading to the ultimate selection of the flight sample composition, including design, fabrication, and testing, all of which are expected to contribute immeasurably to an improved comprehension of materials processing in space. This technical memorandum is directed entirely to the payload manifest flown in the eighth of a series of SPAR flights conducted at the White Sands Missile Range (WSMR) and includes the experiments entitled Glass Formation Experiment SPAR 74-42/1R, Glass Fining Experiment in Low-Gravity SPAR 77-13/1, and Dynamics of Liquid Bubbles SPAR Experiment 77-18/2.

Inactivation of individual Bacillus subtilis spores in dependence on their distance to single cosmic heavy ions.

PubMed

Facius, R; Reitz, G; Schafer, M

1994-10-01

For radiobiological experiments in space, designed to investigate biological effects of the heavy ions of the cosmic radiation field, a mandatory requirement is the possibility to spatially correlate the observed biological response of individual test organisms to the passage of single heavy ions. Among several undertakings towards this goal, the BIOSTACK experiments in the Apollo missions achieved the highest precision and therefore the most detailed information on this question. Spores of Bacillus subtilis as a highly radiation resistant and microscopically small test organism yielded these quantitative results. This paper will focus on experimental and procedural details, which must be included for an interpretation and a discussion of these findings in comparison to control experiments with accelerated heavy ions.

To Draw or Not to Draw? Examining the Necessity of Problem Diagrams Using Massive Open Online Course Experiments

ERIC Educational Resources Information Center

Chen, Zhongzhou; Demirci, Neset; Choi, Youn-Jeng; Pritchard, David E.

2017-01-01

Previous research on problem diagrams suggested that including a supportive diagram, one that does not provide necessary problem solving information, may bring little, or even negative, benefit to students' problem solving success. We tested the usefulness of problem diagrams on 12 different physics problems (6A/B experiments) in our massive open…

Army Communicator. Volume 37, Number 1, Spring 2012

DTIC Science & Technology

2012-01-01

consortium conducts a risk reduction experiment and lab-based assessment on each of them. A successful example of this risk reduction process was the...include pre-experimental assessments , risk mitigation experiments, and configuration testing. The Network Battle Lab is proud to serve as a...experimentation, assessment , rehearsals, SATCOM/network services and vendor mentorship support to the NIE team. COL Michael Brownfield

Viking

NASA Technical Reports Server (NTRS)

1975-01-01

The Viking program, its characteristics, goals, and investigations are described. The program consists of launching two spacecraft to Mars in 1975 to soft-land on the surface and test for signs of life. Topics discussed include the launch, the journey through space, tracking, Mars orbit and landing, experiments on the search for life, imaging systems, lander camera, water detection experiments, thermal mapping, and a possible weather station on Mars.

Defense Acquisitions: Assessments of Selected Weapon Programs

DTIC Science & Technology

2009-03-01

a field experiment , but program officials report that it will take additional efforts to transition the waveform to an operational platform. The...successfully demonstrated during a field experiment ending in October 2008 that included a multi-subnet test by Future Combat Systems personnel. The...Individual Programs 29 Advanced Extremely High Frequency (AEHF) Satellites 31 Advanced Threat Infrared Countermeasure/Common Missile Warning System

The Effects of Conditioned Reinforcement for Reading on Reading Comprehension for 5th Graders

ERIC Educational Resources Information Center

Cumiskey Moore, Colleen

2017-01-01

In three experiments, I tested the effects of the conditioned reinforcement for reading (R+Reading) on reading comprehension with 5th graders. In Experiment 1, I conducted a series of statistical analyses with data from 18 participants for one year. I administered 4 pre/post measurements for reading repertoires which included: 1) state-wide…

Land Warrior (LW)/Mounted Warrior (MW) DOTMLPF Assessment

DTIC Science & Technology

2007-06-01

the DOTMLPF impacts of equipping a Stryker battalion with MW and LW? 3) What is the estimated life cycle cost (LCC) of each LW BOIP alternative? 4...A R E D A T A Assessed costs included: - Support Equipment/Disposal. - Contractor Logistics Support. - Ensemble Hardware...DOTMLPF . 3 - Cost . LUT Navigation Experiment Lethality Experiment AMSAA TRAC-WSMR TRAC-WSMR ATEC LW Test Unit

The Development of the Functional Literacy Experience Scale Based upon Ecological Theory (FLESBUET) and Validity-Reliability Study

ERIC Educational Resources Information Center

Özenç, Emine Gül; Dogan, M. Cihangir

2014-01-01

This study aims to perform a validity-reliability test by developing the Functional Literacy Experience Scale based upon Ecological Theory (FLESBUET) for primary education students. The study group includes 209 fifth grade students at Sabri Taskin Primary School in the Kartal District of Istanbul, Turkey during the 2010-2011 academic year.…

Detection of soil microorganism in situ by combined gas chromatography mass spectrometry

NASA Technical Reports Server (NTRS)

Alexander, M.; Duxbury, J. M.; Francis, A. J.; Adamson, J.

1972-01-01

Experimental tests were made to determine whether analysis of volatile metabolic products, formed in situ, is a viable procedure for an extraterrestrial life detection system. Laboratory experiments, carried out under anaerobic conditions with addition of carbon source, extended to include a variety of soils and additional substrates. In situ experiments were conducted without amendment using a vacuum sampling system.

Simulations in support of the T4B experiment

NASA Astrophysics Data System (ADS)

Qerushi, Artan; Ross, Patrick; Lohff, Chriss; Raymond, Anthony; Montecalvo, Niccolo

2017-10-01

Simulations in support of the T4B experiment are presented. These include a Grad-Shafranov equilibrium solver and equilibrium reconstruction from flux-loop measurements, collision radiative models for plasma spectroscopy (determination of electron density and temperature from line ratios) and fast ion test particle codes for neutral beam - plasma coupling. ©2017 Lockheed Martin Corporation. All Rights Reserved.

Eccentric overload training for patients with chronic Achilles tendon pain--a randomised controlled study with reliability testing of the evaluation methods.

PubMed

Silbernagel, K G; Thomeé, R; Thomeé, P; Karlsson, J

2001-08-01

The purpose was to examine the reliability of measurement techniques and evaluate the effect of a treatment protocol including eccentric overload for patients with chronic pain from the Achilles tendon. Thirty-two patients with proximal achillodynia (44 involved Achilles tendons) participated in tests for reliability measures. No significant differences and strong (r=0.56-0.72) or very strong (r=0.90-0.93) correlations were found between pre-tests, except for the documentation of pain at rest (P<0.008, r=0.45). To evaluate the effect of a 12-week treatment protocol for patients with chronic proximal achillodynia (pain longer than three months) 40 patients (57 involved Achilles tendons) with a mean age of 45 years (range 19-77) were randomised into an experiment group (n=22) and a control group (n=18). Evaluations were performed after six weeks of treatment and after three and six months. The evaluations (including the pre-tests), performed by a physical therapist unaware of the group the patients belonged to, consisted of a questionnaire, a range of motion test, a jumping test, a toe-raise test, a pain on palpation test and pain evaluation during jumping, toe-raises and at rest. A follow-up was also performed after one year. There were no significant differences between groups at any of the evaluations, except that the experiment group jumped significantly lower than the control group at the six-week evaluation. There was, however, an overall better result for the experiment group with significant improvements in plantar flexion, and reduction in pain on palpation, number of patients having pain during walking, having periods when asymptomatic and having swollen Achilles tendon. The controls did not show such changes. Furthermore, at the one-year follow-up there were significantly more patients in the experiment group, compared with the control group, that were satisfied with their present physical activity level, considered themselves fully recovered, and had no pain during or after physical activity. The measurement techniques and the treatment protocol with eccentric overload used in the present study can be recommended for patients with chronic pain from the Achilles tendon.

The development and testing of the Lens Antenna Deployment Demonstration (LADD) test article

NASA Technical Reports Server (NTRS)

Pugh, Mark L.; Denton, Robert J., Jr.; Strange, Timothy J.

1993-01-01

The USAF Rome Laboratory and NASA Marshall Space Flight Center, through contract to Grumman Corporation, have developed a space-qualifiable test article for the Strategic Defense Initiative Organization to demonstrate the critical structural and mechanical elements of single-axis roll-out membrane deployment for Space Based Radar (SBR) applications. The Lens Antenna Deployment Demonstration (LADD) test article, originally designed as a shuttle-attached flight experiment, is a large precision space structure which is representative of operational designs for space-fed lens antennas. Although the flight experiment was cancelled due to funding constraints and major revisions in the Strategic Defense System (SDS) architecture, development of this test article was completed in June 1989. To take full advantage of the existence of this unique structure, a series of ground tests are proposed which include static, dynamic, and thermal measurements in a simulated space environment. An equally important objective of these tests is the verification of the analytical tools used to design and develop large precision space structures.

Evaluation results of xTCA equipment for HEP experiments at CERN

NASA Astrophysics Data System (ADS)

Di Cosmo, M.; Bobillier, V.; Haas, S.; Joos, M.; Mico, S.; Vasey, F.; Vichoudis, P.

2013-12-01

The MicroTCA and AdvancedTCA industry standards are candidate modular electronic platforms for the upgrade of the current generation of high energy physics experiments. The PH-ESE group at CERN launched in 2011 the xTCA evaluation project with the aim of performing technical evaluations and eventually providing support for commercially available components. Different devices from different vendors have been acquired, evaluated and interoperability tests have been performed. This paper presents the test procedures and facilities that have been developed and focuses on the evaluation results including electrical, thermal and interoperability aspects.

Medical Support and Findings of the Skylab Program

NASA Technical Reports Server (NTRS)

Johnston, Richard S.; Dietlein, Lawrence F.

1975-01-01

Specific equipment used in carrying out Skylab medical experiments is outlined and illustrated. Also included are reviews of the techniques, frequency, and protocols of the tests designed to study the long term effects of weightlessness on the human body. In-flight investigations were an evaluation of the cardiovascular system, a study of metabolic activity, investigations in the field of neurophysiology, the determination of changes in body fluids, a precise measurement of total body metabolism, and a study of crew performance by use of a time and motion experiment. Significant data obtained from in-flight and postflight tests are outlined.

Design, development and fabrication of a Solar Experiment Alignment Sensor (SEAS)

NASA Technical Reports Server (NTRS)

Bancroft, J. R.; Fain, M. Z.; Johnson, D. F.

1971-01-01

The design, development and testing of a laboratory SEAS (Solar Experiment Alignment Sensor) system are presented. The system is capable of overcoming traditional alignment and calibration problems to permit pointing anywhere on the solar disc to an accuracy of five arc seconds. The concept, development and laboratory testing phases of the program are discussed, and particular attention has been given to specific problems associated with selection of materials, and components. The conclusions summarize performance capability and discuss areas for further study including the effects of solar limb darkening and effects of annual variations in the apparent solar diameter.

Apparent metabolizable and net energy values of corn and soybean meal for broiler breeding cocks.

PubMed

Liu, W; Liu, G H; Liao, R B; Chang, Y L; Huang, X Y; Wu, Y B; Yang, H M; Yan, H J; Cai, H Y

2017-01-01

The AME and net energy (NE) values of 4 corn varieties, including 2 normal corn varieties (Zheng Dan 958 and Xian Yu 335), and one each of waxy corn and sweet corn, and 2 soybean meal samples including regular (RSBM) and dehulled soybean meal (DSBM), were determined in 2 experiments for broiler breeding cocks using the indirect calorimetry method. The 4 test diets in Experiment 1 consisted of each test corn, which replaced 40% of the corn-soybean meal basal diet, and the test diets in Experiment 2 contained 25% RSBM or DSBM, which was used to replace the corn basal diet. Thirty (Experiment 1) or 18 (Experiment 2) 50-week-old Arbor Acre (AA) broiler breeding cocks were used in a completely randomized design. After a 7 d dietary adaptation period, 6 birds as replicates from each treatment were assigned to individual respiration chambers for energy measurement via gaseous exchange and total excreta collection for 10 d. In Experiment 1, the AME, ME intake (MEI), retained energy (RE), NE, and NE:AME ratio values were higher (P < 0.001) in the test diets as compared with the corn-soybean meal basal diet. The AME and NE values in the sweet corn diet were higher (P < 0.05) than those values in the other 3 test diets. The heat production (HP), fasting heat production (FHP), and respiration quotient (RQ) were not influenced by the various experimental diets. The respective AME and NE values were 3,785, 3,775, 3,738, and 3,997 kcal/kg (DM basis), and 2,982, 3,006, 2,959, and 3,146 kcal/kg (DM basis) for Zheng Dan 958, Xian Yu 335, waxy corn, and sweet corn. Birds fed a corn basal diet in Experiment 2 had higher AME, MEI, RE, NE, and NE:AME ratio values (P < 0.001). Soybean meal substitution had no effect on HP, FHP, or RQ. The average AME and NE content was 2,492 and 1,581 kcal/kg (DM basis) for RSBM, and 2,580 and 1,654 kcal/kg (DM basis) for DSBM, respectively. © 2016 Poultry Science Association Inc.

Integration and Testing Challenges of Small, Multiple Satellite Missions: Experiences From The Space Technology 5 Project

NASA Technical Reports Server (NTRS)

Sauerwein, Timothy A.; Gostomski, Thomas

2007-01-01

This brief presentation describes the mechanical and electrical integration activities and environmental testing challenges of the Space Technology 5 (ST5) Project. Lessons learned during this process are highlighted, including performing mechanical activities serially to gain efficiency through repetition and performing electrical activities based on the level of subsystem expertise available.

Crawling and/or Squatting: A Saleable Work Skill. Occupation Simulation Packet. Grades K-2nd.

ERIC Educational Resources Information Center

Montgomery, Margery

This teacher's guide for grades K-2 contains simulated work experiences for students using the isolated skill concept, crawling and/or squatting. Teacher instructions include objectives, evaluation, and sequence of activities. The guide contains pre-tests and post-tests with instructions and answer keys. Three pre-skill activities are suggested,…

The Development of a Test to Assess Drug Using Behavior.

ERIC Educational Resources Information Center

Althoff, Michael E.

The objective of the study was to develop a test which could measure both the qualitative and quantitative aspects of drug-using behavior, including such factors as attitudes toward drugs, experience with drugs, and knowledge about drugs. The Drug Use Scale was developed containing 134 items and dealing with five classes of drugs: marijuana,…

A Test of the Paired-Associate Analogy to RI in Free Recall.

ERIC Educational Resources Information Center

Perlmutter, Jane; Royer, James M.

To provide a further test of the paired-associate analogy to retroactive inhibition in free recall, this experiment investigated the effect of presenting both original learning (OL) and interpolated learning (IL) in either blocked category (B) or random (R) fashion. IL-OL Similar (S), IL-OL Different (D), and control (C) conditions were included.…

Apollo experience report: Development flight instrumentation. [telemetry equipment for space flight test program

NASA Technical Reports Server (NTRS)

Farmer, N. B.

1974-01-01

Development flight instrumentation was delivered for 25 Apollo vehicles as Government-furnished equipment. The problems and philosophies of an activity that was concerned with supplying telemetry equipment to a space-flight test program are discussed. Equipment delivery dates, system-design details, and flight-performance information for each mission also are included.

Assembling in Sequence: A Saleable Work Skill. Occupation Simulation Packet. Grades 3rd-4th.

ERIC Educational Resources Information Center

Hueston, Jean

This teacher's guide for grades 3 and 4 contains simulated work experiences for students using the isolated skill concept - assembling in sequence. Teacher instructions include objectives, evaluation, and sequence of activities. The guide contains pre-tests and post-tests with instructions and answer keys. Three pre-skill activities are suggested,…

Oral Persuasion: A Saleable Work Skill. Occupation Simulation Packet. Grades 5th-6th.

ERIC Educational Resources Information Center

Lee, Dennis W.

This teacher's guide contains simulated work experiences for 5th and 6th grade students using the isolated skill concept - oral persuasion. Teacher instructions include objectives, evaluation, and sequence of activities. The guide contains pre-tests and post-tests with instructions and answer keys. Two pre-skill activities are suggested, such as…

Dimensions of Intelligent Systems

DTIC Science & Technology

2002-08-01

Keywords: IS, Intelligent Systems, Turing Test, Cognitive Model, situated cognition, BDI, Deep Blue, constructionism 1: Introduction Investigation of...Our social experience provides an implicit, observer bias to assign mentality and intentions to the system in a test and many would argue that...extended the intentional notions of Belief, Desire, and Intention (BDI ) to include social “properties” of Value6

In-Space Structural Validation Plan for a Stretched-Lens Solar Array Flight Experiment

NASA Technical Reports Server (NTRS)

Pappa, Richard S.; Woods-Vedeler, Jessica A.; Jones, Thomas W.

2001-01-01

This paper summarizes in-space structural validation plans for a proposed Space Shuttle-based flight experiment. The test article is an innovative, lightweight solar array concept that uses pop-up, refractive stretched-lens concentrators to achieve a power/mass density of at least 175 W/kg, which is more than three times greater than current capabilities. The flight experiment will validate this new technology to retire the risk associated with its first use in space. The experiment includes structural diagnostic instrumentation to measure the deployment dynamics, static shape, and modes of vibration of the 8-meter-long solar array and several of its lenses. These data will be obtained by photogrammetry using the Shuttle payload-bay video cameras and miniature video cameras on the array. Six accelerometers are also included in the experiment to measure base excitations and small-amplitude tip motions.

Influence of rumen protozoa on methane emission in ruminants: a meta-analysis approach.

PubMed

Guyader, J; Eugène, M; Nozière, P; Morgavi, D P; Doreau, M; Martin, C

2014-11-01

A meta-analysis was conducted to evaluate the effects of protozoa concentration on methane emission from ruminants. A database was built from 59 publications reporting data from 76 in vivo experiments. The experiments included in the database recorded methane production and rumen protozoa concentration measured on the same groups of animals. Quantitative data such as diet chemical composition, rumen fermentation and microbial parameters, and qualitative information such as methane mitigation strategies were also collected. In the database, 31% of the experiments reported a concomitant reduction of both protozoa concentration and methane emission (g/kg dry matter intake). Nearly all of these experiments tested lipids as methane mitigation strategies. By contrast, 21% of the experiments reported a variation in methane emission without changes in protozoa numbers, indicating that methanogenesis is also regulated by other mechanisms not involving protozoa. Experiments that used chemical compounds as an antimethanogenic treatment belonged to this group. The relationship between methane emission and protozoa concentration was studied with a variance-covariance model, with experiment as a fixed effect. The experiments included in the analysis had a within-experiment variation of protozoa concentration higher than 5.3 log10 cells/ml corresponding to the average s.e.m. of the database for this variable. To detect potential interfering factors for the relationship, the influence of several qualitative and quantitative secondary factors was tested. This meta-analysis showed a significant linear relationship between methane emission and protozoa concentration: methane (g/kg dry matter intake)=-30.7+8.14×protozoa (log10 cells/ml) with 28 experiments (91 treatments), residual mean square error=1.94 and adjusted R 2=0.90. The proportion of butyrate in the rumen positively influenced the least square means of this relationship.

An Open-source Community Web Site To Support Ground-Water Model Testing

NASA Astrophysics Data System (ADS)

Kraemer, S. R.; Bakker, M.; Craig, J. R.

2007-12-01

A community wiki wiki web site has been created as a resource to support ground-water model development and testing. The Groundwater Gourmet wiki is a repository for user supplied analytical and numerical recipes, howtos, and examples. Members are encouraged to submit analytical solutions, including source code and documentation. A diversity of code snippets are sought in a variety of languages, including Fortran, C, C++, Matlab, Python. In the spirit of a wiki, all contributions may be edited and altered by other users, and open source licensing is promoted. Community accepted contributions are graduated into the library of analytic solutions and organized into either a Strack (Groundwater Mechanics, 1989) or Bruggeman (Analytical Solutions of Geohydrological Problems, 1999) classification. The examples section of the wiki are meant to include laboratory experiments (e.g., Hele Shaw), classical benchmark problems (e.g., Henry Problem), and controlled field experiments (e.g., Borden landfill and Cape Cod tracer tests). Although this work was reviewed by EPA and approved for publication, it may not necessarily reflect official Agency policy. Mention of trade names or commercial products does not constitute endorsement or recommendation for use.

Space Environmental Effects Testing Capability at the Marshall Space Flight Center

NASA Technical Reports Server (NTRS)

DeWittBurns, H.; Craven, Paul; Finckenor, Miria; Nehls, Mary; Schneider, Todd; Vaughn, Jason

2012-01-01

Understanding the effects of the space environment on materials and systems is fundamental and essential for mission success. If not properly understood and designed for, the effects of the environment can lead to degradation of materials, reduction of functional lifetime, and system failure. In response to this need, the Marshall Space Flight Center has developed world class Space Environmental Effects (SEE) expertise and test facilities to simulate the space environment. Capabilities include multiple unique test systems comprising the most complete SEE testing capability available. These test capabilities include charged particle radiation (electrons, protons, ions), ultraviolet radiation (UV), vacuum ultraviolet radiation (VUV), atomic oxygen, plasma effects, space craft charging, lunar surface and planetary effects, vacuum effects, and hypervelocity impacts as well as the combination of these capabilities. In addition to the uniqueness of the individual test capabilities, MSFC is the only NASA facility where the effects of the different space environments can be tested in one location. Combined with additional analytical capabilities for pre- and post-test evaluation, MSFC is a one-stop shop for materials testing and analysis. The SEE testing and analysis are performed by a team of award winning experts nationally recognized for their contributions in the study of the effects of the space environment on materials and systems. With this broad expertise in space environmental effects and the variety of test systems and equipment available, MSFC is able to customize tests with a demonstrated ability to rapidly adapt and reconfigure systems to meet customers needs. Extensive flight experiment experience bolsters this simulation and analysis capability with a comprehensive understanding of space environmental effects.

Avionics test bed development plan

NASA Technical Reports Server (NTRS)

Harris, L. H.; Parks, J. M.; Murdock, C. R.

1981-01-01

A development plan for a proposed avionics test bed facility for the early investigation and evaluation of new concepts for the control of large space structures, orbiter attached flex body experiments, and orbiter enhancements is presented. A distributed data processing facility that utilizes the current laboratory resources for the test bed development is outlined. Future studies required for implementation, the management system for project control, and the baseline system configuration are defined. A background analysis of the specific hardware system for the preliminary baseline avionics test bed system is included.

Landsat 7 Solar Array Testing Experiences

NASA Technical Reports Server (NTRS)

Helfrich, Daniel

2000-01-01

This paper covers the extensive Landsat 7 solar array flight qualification testing effort. Details of the mechanical design of the solar array and its retention/release system are presented. A testing chronology is provided beginning with the onset of problems encountered at the subsystem level and carrying through the third and final powered-spacecraft ground deployment test. Design fixes and other changes are explained in the same order as they became necessary to flight-qualify the array. Some interesting lessons learned are included along with key references.

Photovoltaic performance and reliability workshop

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kroposki, B

1996-10-01

This proceedings is the compilation of papers presented at the ninth PV Performance and Reliability Workshop held at the Sheraton Denver West Hotel on September 4--6, 1996. This years workshop included presentations from 25 speakers and had over 100 attendees. All of the presentations that were given are included in this proceedings. Topics of the papers included: defining service lifetime and developing models for PV module lifetime; examining and determining failure and degradation mechanisms in PV modules; combining IEEE/IEC/UL testing procedures; AC module performance and reliability testing; inverter reliability/qualification testing; standardization of utility interconnect requirements for PV systems; need activitiesmore » to separate variables by testing individual components of PV systems (e.g. cells, modules, batteries, inverters,charge controllers) for individual reliability and then test them in actual system configurations; more results reported from field experience on modules, inverters, batteries, and charge controllers from field deployed PV systems; and system certification and standardized testing for stand-alone and grid-tied systems.« less

40 CFR 258.53 - Ground-water sampling and analysis requirements.

Code of Federal Regulations, 2011 CFR

2011-07-01

... include consistent sampling and analysis procedures that are designed to ensure monitoring results that... testing period. If a multiple comparisons procedure is used, the Type I experiment wise error rate for...

Chemistry Notes.

ERIC Educational Resources Information Center

School Science Review, 1983

1983-01-01

Presents background information, laboratory procedures, classroom materials/activities, and chemistry experiments. Topics include sublimation, electronegativity, electrolysis, experimental aspects of strontianite, halide test, evaluation of present and future computer programs in chemistry, formula building, care of glass/saturated calomel…

Physics Notes

ERIC Educational Resources Information Center

School Science Review, 1972

1972-01-01

Seventeen experiments in physics are described to demonstrate various physical phenomena. These include the areas of velocity of sound, damped oscillations, plastic deformation of wires, materials, testing, air resistance, spectrum optical filtering, and some new improvised apparatus. (PS)

New Chemicals Program under TSCA Chemical Categories Document

EPA Pesticide Factsheets

The categories included in this compilation represent chemicals for which sufficient assessment experience has been accumulated so that hazard concerns and testing recommendations vary little from chemical to chemical within the category.

Investigating Air Pollution

ERIC Educational Resources Information Center

Carter, Edward J.

1977-01-01

Describes an experiment using live plants and cigarette smoke to demonstrate the effects of air pollution on a living organism. Procedures include growth of the test plants in glass bottles, and construction and operation of smoking machine. (CS)

Identification and ultra-high-performance liquid chromatography coupled with high-resolution mass spectrometry characterization of biosurfactants, including a new surfactin, isolated from oil-contaminated environments.

PubMed

Moro, Glaci V; Almeida, Rafaela T R; Napp, Amanda P; Porto, Carla; Pilau, Eduardo J; Lüdtke, Diogo S; Moro, Angélica V; Vainstein, Marilene H

2018-05-14

Biosurfactant-producing bacteria were isolated from samples collected in areas contaminated with crude oil. The isolates were screened for biosurfactant production using qualitative drop-collapse test, oil-spreading and emulsification assays, and measurement of their tensoactive properties. Five isolates tested positive for in the screening experiments and displayed decrease in the surface tension below 30 mN m -1 . The biosurfactants produced by these isolates were further investigated and their molecular identification revealed that they are bacteria related to the Bacillus genus. Additionally, the biosurfactants produced were chemically characterized via UHPLC-HRMS experiments, indicating the production of surfactin homologues, including a new class of these molecules. © 2018 The Authors. Microbial Biotechnology published by John Wiley & Sons Ltd and Society for Applied Microbiology.

The Optical Depth Sensor (ODS) in the DREAMS package onboard the Exomars Entry Descent and Landing Demonstrator Module

NASA Astrophysics Data System (ADS)

Rannou, P.; Pommereau, J.-P.; Sarkissian, A.; Foujols, T.

2012-09-01

The optical depth sensor (ODS) is designed to retrieve the optical depth of the dust layer and to characterize the high altitude clouds on Mars. It was developped initially for the mission MARS 96, and also was included in the payload of several other missions. The sensor was finally built and used for a field experiment in Africa in order to validate the concept and test the performance. In this work we present main principle of the retrieval, the instrumental concept and the result of the tests performed during the 2004-2005 winter field experiment. It is now included in the package DREAM, which is part of the payload of the EDM on Mars 2016 and associated to two terrestrial campaigns, in tropical environment (Brasil) and in the arctic environment.

Memory load as a cognitive antidote to performance decrements in data entry.

PubMed

Chapman, Mary J; Healy, Alice F; Kole, James A

2016-10-01

In two experiments, subjects trained in data entry, typing one 4-digit number at a time. At training, subjects either typed the numbers immediately after they appeared (immediate) or typed the previous number from memory while viewing the next number (delayed). In Experiment 2 stimulus presentation time was limited and either nothing or a space (gap) was inserted between the second and third digits. In both experiments after training, all subjects completed a test with no gap and typed numbers immediately. Training with a memory load improved speed across training blocks (Experiment 1) and eliminated the decline in accuracy across training blocks (Experiment 2), thus serving as a cognitive antidote to performance decrements. An analysis of each keystroke revealed different underlying processes and strategies for the two training conditions, including when encoding took place. Chunking (in which the first and last two digits are treated separately) was more evident in the immediate than in the delayed condition and was exaggerated with a gap, even at test when there was no gap. These results suggest that such two-digit chunking is due to stimulus encoding and motor planning processes as well as memory, and those processes transferred from training to testing.

Upscaling of U(VI) Desorption and Transport from Decimeter-Scale Heterogeneity to Plume-Scale Modeling

DOE Office of Scientific and Technical Information (OSTI.GOV)

Curtis, Gary P.; Kohler, Matthias; Kannappan, Ramakrishnan

2015-02-24

Scientifically defensible predictions of field scale U(VI) transport in groundwater requires an understanding of key processes at multiple scales. These scales range from smaller than the sediment grain scale (less than 10 μm) to as large as the field scale which can extend over several kilometers. The key processes that need to be considered include both geochemical reactions in solution and at sediment surfaces as well as physical transport processes including advection, dispersion, and pore-scale diffusion. The research summarized in this report includes both experimental and modeling results in batch, column and tracer tests. The objectives of this research weremore » to: (1) quantify the rates of U(VI) desorption from sediments acquired from a uranium contaminated aquifer in batch experiments;(2) quantify rates of U(VI) desorption in column experiments with variable chemical conditions, and(3) quantify nonreactive tracer and U(VI) transport in field tests.« less

Global bias reliability in dogs (Canis familiaris).

PubMed

Mongillo, Paolo; Pitteri, Elisa; Sambugaro, Pamela; Carnier, Paolo; Marinelli, Lieta

2017-03-01

Dogs enrolled in a previous study were assessed two years later for reliability of their local/global preference in a discrimination test with the same hierarchical stimuli used in the previous study (Experiment 1) and with a novel stimulus (Experiment 2). In Experiment 1, dogs easily re-learned to discriminate the positive stimulus; their individual global/local choices were stable compared to the previous study; and an overall clear global bias was found. In Experiment 2, dogs were slower in acquiring the initial discrimination task; the overall global bias disappeared; and, individually, dogs tended to make inverse choices compared to the original study. Spontaneous attention toward the test stimulus resembling the global features of the probe stimulus was the main factor affecting the likeliness of a global choice of our dogs, regardless of the type of experiment. However, attention to task-irrelevant elements increased at the expense of attention to the stimuli in the test phase of Experiment 2. Overall, the results suggest that the stability of global bias in dogs depends on the characteristics of the assessment contingencies, likely including the learning requirements of the tasks. Our results also clearly indicate that attention processes have a prominent role on dogs' global bias, in agreement with previous findings in humans and other species.

PANDA asymmetric-configuration passive decay heat removal test results

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fischer, O.; Dreier, J.; Aubert, C.

1997-12-01

PANDA is a large-scale, low-pressure test facility for investigating passive decay heat removal systems for the next generation of LWRs. In the first series of experiments, PANDA was used to examine the long-term LOCA response of the Passive Containment Cooling System (PCCS) for the General Electric (GE) Simplified Boiling Water Reactor (SBWR). The test objectives include concept demonstration and extension of the database available for qualification of containment codes. Also included is the study of the effects of nonuniform distributions of steam and noncondensable gases in the Dry-well (DW) and in the Suppression Chamber (SC). 3 refs., 9 figs.

Methodical aspects of text testing in a driving simulator.

PubMed

Sundin, A; Patten, C J D; Bergmark, M; Hedberg, A; Iraeus, I-M; Pettersson, I

2012-01-01

A test with 30 test persons was conducted in a driving simulator. The test was a concept exploration and comparison of existing user interaction technologies for text message handling with focus on traffic safety and experience (technology familiarity and learning effects). Focus was put on methodical aspects how to measure and how to analyze the data. Results show difficulties with the eye tracking system (calibration etc.) per se, and also include the subsequent raw data preparation. The physical setup in the car where found important for the test completion.

Remote Advanced Payload Test Rig (RAPTR) Portable Payload Test System for the International Space Station

NASA Technical Reports Server (NTRS)

De La Cruz, Melinda; Henderson, Steve

2016-01-01

The RAPTR was developed to test ISS payloads for NASA. RAPTR is a simulation of the Command and Data Handling (C&DH) interfaces of the ISS (MIL-STD1553B, Ethernet and TAXI) and is designed for rapid testing and deployment of payload experiments to the ISS. The ISS's goal is to reduce the amount of time it takes for a payload developer to build, test and fly a payload, including payload software. The RAPTR meets this need with its user oriented, visually rich interface.

Experimental evaluation of the Battelle accelerated test design for the solar array at Mead, Nebraska

NASA Technical Reports Server (NTRS)

Frickland, P. O.; Repar, J.

1982-01-01

A previously developed test design for accelerated aging of photovoltaic modules was experimentally evaluated. The studies included a review of relevant field experience, environmental chamber cycling of full size modules, and electrical and physical evaluation of the effects of accelerated aging during and after the tests. The test results indicated that thermally induced fatigue of the interconnects was the primary mode of module failure as measured by normalized power output. No chemical change in the silicone encapsulant was detectable after 360 test cycles.

Outline of CS application experiments

NASA Astrophysics Data System (ADS)

Otsu, Y.; Kondoh, K.; Matsumoto, M.

1985-09-01

To promote and investigate the practical application of satellite use, CS application experiments for various social activity needs, including those of public services such as the National Police Agency and the Japanese National Railway, computer network services, news material transmissions, and advanced teleconference activities, were performed. Public service satellite communications systems were developed and tested. Based on results obtained, several public services have implemented CS-2 for practical disaster-back-up uses. Practical application computer network and enhanced video-conference experiments have also been performed.

First Spacelab mission status and lessons learned

NASA Technical Reports Server (NTRS)

Craft, H. G., Jr.; Smith, M. J.; Mullinger, D.

1982-01-01

There are 38 experiments and/or facilities currently under development, or undergoing testing, which will be incorporated into Spacelab for its first mission. These experiments cover a range of scientific disciplines which includes atmospheric research, life sciences, space plasma research, materials science, and space industrialization technology. In addition to the full development of individual experiments, the final design of the integrated payload and the development of all requisite integration hardware have been accomplished. Attention is given to the project management lessons learned during payload integration development.

Progress of the LASSO experiment

NASA Technical Reports Server (NTRS)

Serene, B. E. H.

1981-01-01

The LASSO (Later Synchronisation from Stationary Orbit) experiment, designed to demonstrate the feasibility of achieving time synchronization between remote atomic clocks with an accuracy of one nanosecond or better by using laser techniques for the first time is described. The experiment uses groundbased laser stations and the SIRIO-2 geostationary satellite to be launched towards the end of 1981. The qualification of the LASSO on-board equipment is discussed with a brief description of the electrical and optical test equipment used. The progress of the operational organization is included.

Mars Pathfinder Microrover- Implementing a Low Cost Planetary Mission Experiment

NASA Technical Reports Server (NTRS)

Matijevic, J.

1996-01-01

The Mars Pathfinder Microrover Flight Experiment (MFEX) is a NASA Office of Space Access and Technology (OSAT) flight experiment which has been delivered and integrated with the Mars Pathfinder (MPF) lander and spacecraft system. The total cost of the MFEX mission, including all subsystem design and development, test, integration with the MPF lander and operations on Mars has been capped at $25 M??is paper discusses the process and the implementation scheme which has resulted in the development of this first Mars rover.

Formal and Informal Learning and First-Year Psychology Students’ Development of Scientific Thinking: A Two-Wave Panel Study

PubMed Central

Soyyılmaz, Demet; Griffin, Laura M.; Martín, Miguel H.; Kucharský, Šimon; Peycheva, Ekaterina D.; Vaupotič, Nina; Edelsbrunner, Peter A.

2017-01-01

Scientific thinking is a predicate for scientific inquiry, and thus important to develop early in psychology students as potential future researchers. The present research is aimed at fathoming the contributions of formal and informal learning experiences to psychology students’ development of scientific thinking during their 1st-year of study. We hypothesize that informal experiences are relevant beyond formal experiences. First-year psychology student cohorts from various European countries will be assessed at the beginning and again at the end of the second semester. Assessments of scientific thinking will include scientific reasoning skills, the understanding of basic statistics concepts, and epistemic cognition. Formal learning experiences will include engagement in academic activities which are guided by university authorities. Informal learning experiences will include non-compulsory, self-guided learning experiences. Formal and informal experiences will be assessed with a newly developed survey. As dispositional predictors, students’ need for cognition and self-efficacy in psychological science will be assessed. In a structural equation model, students’ learning experiences and personal dispositions will be examined as predictors of their development of scientific thinking. Commonalities and differences in predictive weights across universities will be tested. The project is aimed at contributing information for designing university environments to optimize the development of students’ scientific thinking. PMID:28239363

Formal and Informal Learning and First-Year Psychology Students' Development of Scientific Thinking: A Two-Wave Panel Study.

PubMed

Soyyılmaz, Demet; Griffin, Laura M; Martín, Miguel H; Kucharský, Šimon; Peycheva, Ekaterina D; Vaupotič, Nina; Edelsbrunner, Peter A

2017-01-01

Scientific thinking is a predicate for scientific inquiry, and thus important to develop early in psychology students as potential future researchers. The present research is aimed at fathoming the contributions of formal and informal learning experiences to psychology students' development of scientific thinking during their 1st-year of study. We hypothesize that informal experiences are relevant beyond formal experiences. First-year psychology student cohorts from various European countries will be assessed at the beginning and again at the end of the second semester. Assessments of scientific thinking will include scientific reasoning skills, the understanding of basic statistics concepts, and epistemic cognition. Formal learning experiences will include engagement in academic activities which are guided by university authorities. Informal learning experiences will include non-compulsory, self-guided learning experiences. Formal and informal experiences will be assessed with a newly developed survey. As dispositional predictors, students' need for cognition and self-efficacy in psychological science will be assessed. In a structural equation model, students' learning experiences and personal dispositions will be examined as predictors of their development of scientific thinking. Commonalities and differences in predictive weights across universities will be tested. The project is aimed at contributing information for designing university environments to optimize the development of students' scientific thinking.

Thermal Vacuum Testing of a Multi-Evaporator Miniature Loop Heat Pipe

NASA Technical Reports Server (NTRS)

Ku, Jentung; Ottenstein, Laura; Nagano, Hosei

2008-01-01

Under NASA's New Millennium Program Space Technology 8 Project, four experiments are being developed for future small system applications requiring low mass, low power, and compactness. GSFC is responsible for developing the Thermal Loop experiment, which is an advanced thermal control system consisting of a miniature loop heat pipe (MLHP) with multiple evaporators and condensers. The objective is to validate the operation of an MLHP, including reliable start-ups, steady operation, heat load sharing, and tight temperature control over the range of 273K to 308K. An MLHP Breadboard has been built and tested for 1200 hours under the laboratory environment and 500 hours in a thermal vacuum chamber. Results of the TV tests are presented here.

Couple experiences of provider-initiated couple HIV testing in an antenatal clinic in Lusaka, Zambia: lessons for policy and practice.

PubMed

Musheke, Maurice; Bond, Virginia; Merten, Sonja

2013-03-14

Couple HIV testing has been recognized as critical to increase uptake of HIV testing, facilitate disclosure of HIV status to marital partner, improve access to treatment, care and support, and promote safe sex. The Zambia national protocol on integrated prevention of mother-to-child transmission of HIV (PMTCT) allows for the provision of couple testing in antenatal clinics. This paper examines couple experiences of provider-initiated couple HIV testing at a public antenatal clinic and discusses policy and practical lessons. Using a narrative approach, open-ended in-depth interviews were held with couples (n = 10) who underwent couple HIV testing; women (n = 5) and men (n = 2) who had undergone couple HIV testing but were later abandoned by their spouses; and key informant interviews with lay counsellors (n = 5) and nurses (n = 2). On-site observations were also conducted at the antenatal clinic and HIV support group meetings. Data collection was conducted between March 2010 and September 2011. Data was organised and managed using Atlas ti, and analysed and interpreted thematically using content analysis approach. Health workers sometimes used coercive and subtle strategies to enlist women's spouses for couple HIV testing resulting in some men feeling 'trapped' or 'forced' to test as part of their paternal responsibility. Couple testing had some positive outcomes, notably disclosure of HIV status to marital partner, renewed commitment to marital relationship, uptake of and adherence to treatment and formation of new social networks. However, there were also negative repercussions including abandonment, verbal abuse and cessation of sexual relations. Its promotion also did not always lead to safe sex as this was undermined by gendered power relationships and the desires for procreation and sexual intimacy. Couple HIV testing provides enormous bio-medical and social benefits and should be encouraged. However, testing strategies need to be non-coercive. Providers of couple HIV testing also need to be mindful of the intimate context of partner relationships including couples' childbearing aspirations and lived experiences. There is also need to make antenatal clinics more male-friendly and responsive to men's health needs, as well as being attentive and responsive to gender inequality during couselling sessions.

Pilot, a balloon borne experiment underground tests

NASA Astrophysics Data System (ADS)

Engel, C.; Marty, C.; Mot, B.; Bernard, J.-Ph.; Ristorcelli, I.; Otrio, G.; Leriche, B.; Longval, Y.; Pajot, F.; Roudil, G.; Caillat, A.; Dubois, J. P.; Bouzit, M.; Buttice, V.; Camus, T.

2017-11-01

PILOT is a balloon borne experiment, which will measure the polarized emission of dust grains, in the interstellar medium, in the sub millimeter range (with two photometric channels centered at 240 and 550 μm). The primary and secondary mirror must be positioned with accuracies better than 0.6 mm and 0.06°. These tolerances include environmental conditions (mainly gravity and thermo-elastic effects), uncertainties on alignments, and uncertainties on the dilatation coefficient. In order to respect these tolerances, we need precise characterization of each optical component. The characterization of the primary mirror and the integrated instrument is performed using a dedicated submillimeter test bench. A brief description of the scientific objectives and instrumental concept is given in the first part. We present, in the second and in the third part, the status of these ground tests, first results and planned tests.

Status and future plans of the Drones for Aerodynamic and Structural Testing (DAST) program. [Aeroelastic Research Wing (ARW)

NASA Technical Reports Server (NTRS)

Murrow, H. N.

1981-01-01

Results from flight tests of the ARW-1 research wing are presented. Preliminary loads data and experiences with the active control system for flutter suppression are included along with comparative results of test and prediction for the flutter boundary of the supercritical research wing and on performance of the flutter suppression system. The status of the ARW-2 research wing is given.

The Impact of Prior Deployment Experience on Civilian Employment After Military Service

DTIC Science & Technology

2013-03-21

covariates men- tioned. Given the exploratory nature of this study, all defined variables were included. Model diagnostic tests were conducted and we...assessed model fit using the Hosmer–Lemeshow goodness-of-fit test . To identify the existence of collinearity, we examined all variance inflation factors...separation, and reason for separation and service branch were tested . Both interactions were significant at pɘ.10. Three models were built to examine

MISTY PICTURE EVENT, Test Execution Report

DTIC Science & Technology

1987-11-30

testbed at overpressures ranging from 10 psi (83 kPa) to 3.4 psi (23 kPa). A series of experiments were positioned near the Thermal Radiation Sources...to include scheduling, construction, photography, and recording systems. (2) Formulate and direct the safety and security plans for the test series and...ANFO stacked charges multiburst test at Planet Ranch, AZ in 1978, e. MILL RACE (MISTY CASTLE Series I) - 600 ton ANFO surface stacked charge at WSMR in

Reevaluating excess success in psychological science.

PubMed

van Boxtel, Jeroen J A; Koch, Christof

2016-10-01

Francis (Psychonomic Bulletin Review, 21, 1180-1187, 2014) recently claimed that 82 % of articles with four or more experiments published in Psychological Science between 2009 and 2012 cannot be trusted. We critique Francis' analysis and point out the dependence of his approach on including the appropriate experiments and significance tests. We focus on one of the articles (van Boxtel & Koch, in Psychological Science, 23(4), 410-418, 2012) flagged by Francis and show that the inappropriate inclusion of experiments and tests have led Francis to mistakenly flag this article. We found that decisions about whether to include certain tests potentially affect 34 of the 44 articles analyzed by Francis. We further performed p-curve analyses on the articles discussed in Francis' analysis. We found that 9 of 44 studies showed significant evidential value, 11 studies showed insufficient evidential value, and 1 study showed evidence of p-hacking. Our reevaluation is important, because some researchers may have gained the false impression that none of the quoted articles in Psychological Science can be trusted (as stated by Francis). The analysis by Francis is most likely insufficient to warrant this conclusion for some articles and certainly is insufficient with respect to the study by van Boxtel and Koch (Psychological Science, 23, 410-418, 2012).

Preliminary investigation of Faraday rotation effects and description of polarization measurements on the AFGL high latitude meteor scatter test bed

NASA Astrophysics Data System (ADS)

Ostergaard, Jens C.

1989-01-01

The background, methodology and preliminary results of an investigation of Faraday rotation effects on the Meteor Scatter High Latitude Test Bed in Greenland are presented. A short review of polarization theory for radio waves, presenting basic properties and changes when reflected from the surface of the earth or propagated through the ionosphere is included. Material published by other workers is presented to give the background for the current interest in Faraday rotation on meteor scatter links. Propagation losses for meteor scatter paths originate from spatial spreading of RF energy, scattering losses at the meteor trail, ionospheric absorption and polarization mismatch at the receiving antenna. That part of the polarization mismatch generated by the ionosphere, the Faraday rotation, is described and evaluated. A method to compute the Faraday rotation is presented and results obtained for the AFGL MSHL Test Bed are given. An experiment, including the measurement of signal strength and polarization throughout the lifetime of the individual meteor scatter return is needed to fully assess the combined affects of absorption and depolarization during both quiet and disturbed ionospheric conditions. The measurement accuracy to be expected from a proposed experiment is evaluated. A few examples of meteor scatter returns obtained with a prototype experiment in Greenland are shown and discussed.

Universal Test Facility

NASA Technical Reports Server (NTRS)

Laughery, Mike

1994-01-01

A universal test facility (UTF) for Space Station Freedom is developed. In this context, universal means that the experimental rack design must be: automated, highly marketable, and able to perform diverse microgravity experiments according to NASA space station requirements. In order to fulfill these broad objectives, the facility's customers, and their respective requirements, are first defined. From these definitions, specific design goals and the scope of the first phase of this project are determined. An examination is first made into what types of research are most likely to make the UTF marketable. Based on our findings, the experiments for which the UTF would most likely be used included: protein crystal growth, hydroponics food growth, gas combustion, gallium arsenide crystal growth, microorganism development, and cell encapsulation. Therefore, the UTF is designed to fulfill all of the major requirements for the experiments listed above. The versatility of the design is achieved by taking advantage of the many overlapping requirements presented by these experiments.

Universal Test Facility

NASA Astrophysics Data System (ADS)

Laughery, Mike

A universal test facility (UTF) for Space Station Freedom is developed. In this context, universal means that the experimental rack design must be: automated, highly marketable, and able to perform diverse microgravity experiments according to NASA space station requirements. In order to fulfill these broad objectives, the facility's customers, and their respective requirements, are first defined. From these definitions, specific design goals and the scope of the first phase of this project are determined. An examination is first made into what types of research are most likely to make the UTF marketable. Based on our findings, the experiments for which the UTF would most likely be used included: protein crystal growth, hydroponics food growth, gas combustion, gallium arsenide crystal growth, microorganism development, and cell encapsulation. Therefore, the UTF is designed to fulfill all of the major requirements for the experiments listed above. The versatility of the design is achieved by taking advantage of the many overlapping requirements presented by these experiments.

MHD simulation of plasma compression experiments

NASA Astrophysics Data System (ADS)

Reynolds, Meritt; Barsky, Sandra; de Vietien, Peter

2017-10-01

General Fusion (GF) is working to build a magnetized target fusion (MTF) power plant based on compression of magnetically-confined plasma by liquid metal. GF is testing this compression concept by collapsing solid aluminum liners onto plasmas formed by coaxial helicity injection in a series of experiments called PCS (Plasma Compression, Small). We simulate the PCS experiments using the finite-volume MHD code VAC. The single-fluid plasma model includes temperature-dependent resistivity and anisotropic heat transport. The time-dependent curvilinear mesh for MHD simulation is derived from LS-DYNA simulations of actual field tests of liner implosion. We will discuss how 3D simulations reproduced instability observed in the PCS13 experiment and correctly predicted stabilization of PCS14 by ramping the shaft current during compression. We will also present a comparison of simulated Mirnov and x-ray diagnostics with experimental measurements indicating that PCS14 compressed well to a linear compression ratio of 2.5:1.

Note: Planetary gravities made simple: Sample test of a Mars rover wheel.

PubMed

Viera-López, G; Serrano-Muñoz, A; Amigó-Vega, J; Cruzata, O; Altshuler, E

2017-08-01

We introduce an instrument for a wide spectrum of experiments on gravities other than our planet's. It is based on a large Atwood machine where one of the loads is a bucket equipped with a single board computer and different sensors. The computer is able to detect the falling (or rising) and then the stabilization of the effective gravity and to trigger actuators depending on the experiment. Gravities within the range 0.4 g-1.2 g are easily achieved with acceleration noise of the order of 0.01 g. Under Martian gravity, we are able to perform experiments of approximately 1.5 s duration. The system includes features such as WiFi and a web interface with tools for the setup, monitoring, and data analysis of the experiment. We briefly show a case study in testing the performance of a model Mars rover wheel in low gravities.

Note: Planetary gravities made simple: Sample test of a Mars rover wheel

NASA Astrophysics Data System (ADS)

Viera-López, G.; Serrano-Muñoz, A.; Amigó-Vega, J.; Cruzata, O.; Altshuler, E.

2017-08-01

We introduce an instrument for a wide spectrum of experiments on gravities other than our planet's. It is based on a large Atwood machine where one of the loads is a bucket equipped with a single board computer and different sensors. The computer is able to detect the falling (or rising) and then the stabilization of the effective gravity and to trigger actuators depending on the experiment. Gravities within the range 0.4 g-1.2 g are easily achieved with acceleration noise of the order of 0.01 g. Under Martian gravity, we are able to perform experiments of approximately 1.5 s duration. The system includes features such as WiFi and a web interface with tools for the setup, monitoring, and data analysis of the experiment. We briefly show a case study in testing the performance of a model Mars rover wheel in low gravities.

Integrating gender and sex to unpack trends in sexually transmitted infection surveillance data in British Columbia, Canada: an ethno-epidemiological study

PubMed Central

Knight, Rod; Falasinnu, Titilola; Oliffe, John L; Gilbert, Mark; Small, Will; Goldenberg, Shira; Shoveller, Jean

2016-01-01

Objectives Surveillance data frequently indicate that young men and women experience high—yet considerably different—reported rates of sexually transmitted infections (STIs), including bacterial infections such as chlamydia. We examined how several sex-based (eg, biological) and gender-based (eg, sociocultural) factors may interact to influence STI surveillance data trends. Methods Employing ethno-epidemiological techniques, we analysed cross-sectional qualitative data collected between 2006 and 2013 about young people's experiences accessing STI testing services in five communities in British Columbia, Canada. These data included 250 semistructured interviews with young men and women aged 15–24 years, as well as 39 clinicians who provided STI testing services. Results The findings highlight how young women are socially and medically encouraged to regularly test, while young men are rarely offered similar opportunities. Instead, young men tend to seek out testing services: (1) at the beginning or end of a sexual relationship; (2) after a high-risk sexual encounter; (3) after experiencing symptoms; or (4) based on concerns about ‘abnormal’ sexual anatomy. Our results illustrate how institutions and individuals align with stereotypical gender norms regarding sexual health responsibilities, STI testing and STI treatments. While these patterns reflect social phenomena, they also appear to intersect with sex-based, biological experiences of symptomatology in ways that might help to further explain systematic differences between young men's and women's patterns of testing for STIs. Conclusions The results point to the importance of taking a social and biological view to understanding the factors that contribute to the gap between young men's and women's routine engagement in STI care. PMID:27566628

Integrating gender and sex to unpack trends in sexually transmitted infection surveillance data in British Columbia, Canada: an ethno-epidemiological study.

PubMed

Knight, Rod; Falasinnu, Titilola; Oliffe, John L; Gilbert, Mark; Small, Will; Goldenberg, Shira; Shoveller, Jean

2016-08-26

Surveillance data frequently indicate that young men and women experience high-yet considerably different-reported rates of sexually transmitted infections (STIs), including bacterial infections such as chlamydia. We examined how several sex-based (eg, biological) and gender-based (eg, sociocultural) factors may interact to influence STI surveillance data trends. Employing ethno-epidemiological techniques, we analysed cross-sectional qualitative data collected between 2006 and 2013 about young people's experiences accessing STI testing services in five communities in British Columbia, Canada. These data included 250 semistructured interviews with young men and women aged 15-24 years, as well as 39 clinicians who provided STI testing services. The findings highlight how young women are socially and medically encouraged to regularly test, while young men are rarely offered similar opportunities. Instead, young men tend to seek out testing services: (1) at the beginning or end of a sexual relationship; (2) after a high-risk sexual encounter; (3) after experiencing symptoms; or (4) based on concerns about 'abnormal' sexual anatomy. Our results illustrate how institutions and individuals align with stereotypical gender norms regarding sexual health responsibilities, STI testing and STI treatments. While these patterns reflect social phenomena, they also appear to intersect with sex-based, biological experiences of symptomatology in ways that might help to further explain systematic differences between young men's and women's patterns of testing for STIs. The results point to the importance of taking a social and biological view to understanding the factors that contribute to the gap between young men's and women's routine engagement in STI care. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/

FLORIDA TOWER FOOTPRINT EXPERIMENTS

DOE Office of Scientific and Technical Information (OSTI.GOV)

WATSON,T.B.; DIETZ, R.N.; WILKE, R.

2007-01-01

The Florida Footprint experiments were a series of field programs in which perfluorocarbon tracers were released in different configurations centered on a flux tower to generate a data set that can be used to test transport and dispersion models. These models are used to determine the sources of the CO{sub 2} that cause the fluxes measured at eddy covariance towers. Experiments were conducted in a managed slash pine forest, 10 km northeast of Gainesville, Florida, in 2002, 2004, and 2006 and in atmospheric conditions that ranged from well mixed, to very stable, including the transition period between convective conditions atmore » midday to stable conditions after sun set. There were a total of 15 experiments. The characteristics of the PFTs, details of sampling and analysis methods, quality control measures, and analytical statistics including confidence limits are presented. Details of the field programs including tracer release rates, tracer source configurations, and configuration of the samplers are discussed. The result of this experiment is a high quality, well documented tracer and meteorological data set that can be used to improve and validate canopy dispersion models.« less

Computerized screening for cognitive impairment in patients with COPD.

PubMed

Campman, Carlijn; van Ranst, Dirk; Meijer, Jan Willem; Sitskoorn, Margriet

2017-01-01

COPD is associated with cognitive impairment. These impairments should be diagnosed, but due to time- and budget-reasons, they are often not investigated. The aim of this study is to examine the viability of a brief computerized cognitive test battery, Central Nervous System Vital Signs (CNSVS), in COPD patients. Patients with COPD referred to tertiary pulmonary rehabilitation were included. Cognitive functioning of patients was assessed with CNSVS before pulmonary rehabilitation and compared with age-corrected CNSVS norms. CNSVS is a 30 minute computerized test battery that includes tests of verbal and visual memory, psychomotor speed, processing speed, cognitive flexibility, complex attention, executive functioning, and reaction time. CNSVS was fully completed by 205 (93.2%, 105 females, 100 males) of the total group of patients (n=220, 116 females, 104 males). Z -tests showed that COPD patients performed significantly worse than the norms on all CNSVS cognitive domains. Slightly more than half of the patients (51.8%) had impaired functioning on 1 or more cognitive domains. Patients without computer experience performed significantly worse on CNSVS than patients using the computer frequently. The completion rate of CNSVS was high and cognitive dysfunctions measured with this screening were similar to the results found in prior research, including paper and pen cognitive tests. These results support the viability of this brief computerized cognitive screening in COPD patients, that may lead to better care for these patients. Cognitive performance of patients with little computer experience should be interpreted carefully. Future research on this issue is needed.

Sixth plot of the carcinogenic potency database: results of animal bioassays published in the General Literature 1989 to 1990 and by the National Toxicology Program 1990 to 1993.

PubMed Central

Gold, L S; Manley, N B; Slone, T H; Garfinkel, G B; Ames, B N; Rohrbach, L; Stern, B R; Chow, K

1995-01-01

This paper presents two types of information from the Carcinogenic Potency Database (CPDB): (a) the sixth chronological plot of analyses of long-term carcinogenesis bioassays, and (b) an index to chemicals in all six plots, including a summary compendium of positivity and potency for each chemical (Appendix 14). The five earlier plots of the CPDB have appeared in this journal, beginning in 1984 (1-5). Including the plot in this paper, the CPDB reports results of 5002 experiments on 1230 chemicals. This paper includes bioassay results published in the general literature between January 1989 and December 1990, and in Technical Reports of the National Toxicology Program between January 1990 and June 1993. Analyses are included on 17 chemicals tested in nonhuman primates by the Laboratory of Chemical Pharmacology, National Cancer Institute. This plot presents results of 531 long-term, chronic experiments of 182 test compounds and includes the same information about each experiment in the same plot format as the earlier papers: the species and strain of test animal, the route and duration of compound administration, dose level and other aspects of experimental protocol, histopathology and tumor incidence, TD50 (carcinogenic potency) and its statistical significance, dose response, author's opinion about carcinogenicity, and literature citation. We refer the reader to the 1984 publications (1,6,7) for a detailed guide to the plot of the database, a complete description of the numerical index of carcinogenic potency, and a discussion of the sources of data, the rationale for the inclusion of particular experiments and particular target sites, and the conventions adopted in summarizing the literature. The six plots of the CPDB are to be used together since results of individual experiments that were published earlier are not repeated. Appendix 14 is designed to facilitate access to results on all chemicals. References to the published papers that are the source of experimental data are reported in each of the published plots. For readers using the CPDB extensively, a combined plot is available of all results from the six separate plot papers, ordered alphabetically by chemical; the combined plot in printed form or on computer tape or diskette is available from the first author. A SAS database is also available. PMID:8741772

Fatigue data for polyether ether ketone (PEEK) under fully-reversed cyclic loading

PubMed Central

Shrestha, Rakish; Simsiriwong, Jutima; Shamsaei, Nima

2016-01-01

In this article, the data obtained from the uniaxial fully-reversed fatigue experiments conducted on polyether ether ketone (PEEK), a semi-crystalline thermoplastic, are presented. The tests were performed in either strain-controlled or load-controlled mode under various levels of loading. The data are categorized into four subsets according to the type of tests, including (1) strain-controlled fatigue tests with adjusted frequency to obtain the nominal temperature rise of the specimen surface, (2) strain-controlled fatigue tests with various frequencies, (3) load-controlled fatigue tests without step loadings, and (4) load-controlled fatigue tests with step loadings. Accompanied data for each test include the fatigue life, the maximum (peak) and minimum (valley) stress–strain responses for each cycle, and the hysteresis stress–strain responses for each collected cycle in a logarithmic increment. A brief description of the experimental method is also given. PMID:26937465

Fatigue data for polyether ether ketone (PEEK) under fully-reversed cyclic loading.

PubMed

Shrestha, Rakish; Simsiriwong, Jutima; Shamsaei, Nima

2016-03-01

In this article, the data obtained from the uniaxial fully-reversed fatigue experiments conducted on polyether ether ketone (PEEK), a semi-crystalline thermoplastic, are presented. The tests were performed in either strain-controlled or load-controlled mode under various levels of loading. The data are categorized into four subsets according to the type of tests, including (1) strain-controlled fatigue tests with adjusted frequency to obtain the nominal temperature rise of the specimen surface, (2) strain-controlled fatigue tests with various frequencies, (3) load-controlled fatigue tests without step loadings, and (4) load-controlled fatigue tests with step loadings. Accompanied data for each test include the fatigue life, the maximum (peak) and minimum (valley) stress-strain responses for each cycle, and the hysteresis stress-strain responses for each collected cycle in a logarithmic increment. A brief description of the experimental method is also given.

Does length or neighborhood size cause the word length effect?

PubMed

Jalbert, Annie; Neath, Ian; Surprenant, Aimée M

2011-10-01

Jalbert, Neath, Bireta, and Surprenant (2011) suggested that past demonstrations of the word length effect, the finding that words with fewer syllables are recalled better than words with more syllables, included a confound: The short words had more orthographic neighbors than the long words. The experiments reported here test two predictions that would follow if neighborhood size is a more important factor than word length. In Experiment 1, we found that concurrent articulation removed the effect of neighborhood size, just as it removes the effect of word length. Experiment 2 demonstrated that this pattern is also found with nonwords. For Experiment 3, we factorially manipulated length and neighborhood size, and found only effects of the latter. These results are problematic for any theory of memory that includes decay offset by rehearsal, but they are consistent with accounts that include a redintegrative stage that is susceptible to disruption by noise. The results also confirm the importance of lexical and linguistic factors on memory tasks thought to tap short-term memory.

Results From Phase-1 and Phase-2 GOLD Experiments

NASA Technical Reports Server (NTRS)

Wilson, K.; Jeganathan, M.; Lesh, J. R.; James, J.; Xu, G.

1997-01-01

The Ground/Orbiter Lasercomm Demonstration conducted between the Japanese Engineering Test Satellite (ETS-VI) and the ground station at JPL's Table Mountain Facility, Wrightwood, California, was the rst ground-to-space two-way optical communications experiment. Experiment objectives included validating the performance predictions of the optical link. Atmospheric attenuation and seeing measurements were made during the experiment, and data were analyzed. Downlink telemetry data recovered over the course of the experiment provided information on in-orbit performance of the ETS-VI's laser communications equipment. Biterror rates as low as 10 4 were measured on the uplink and 10 5 on the downlink. Measured signal powers agreed well with theoretical predictions.

Female Hamster Preference for Odors is Not Regulated by Circulating Gonadal Hormones

PubMed Central

Eidson, Lori N.; Maras, Pamela M.; Epperson, Erin; Petrulis, Aras

2009-01-01

Proceptive and receptive behaviors of female rodents, such as golden hamsters, are often regulated by changes in circulating levels of ovarian hormones. However, less is known about how ovarian hormones might regulate female hamster’s attraction and preference for volatile odor from males. To evaluate this, we assessed female preference by recording investigation and proximity to male and female volatile odorants in a Y-maze across all days of the estrous cycle (Experiment 1 & 2) or following ovariectomy (Experiment 3). In Experiment 1, female subjects were tested four times, once on each day of their estrous cycle. Females showed a preference for male odors on diestrus day 1 and to a lesser degree on proestrus, but showed no preference on the day of behavioral estrus. Irrespective of cycle day, preference was apparent in the first few days of testing and disappeared by the fourth day, suggesting that repeated testing attenuated female preference. To avoid this problem, in Experiment 2 each animal was tested only on one day of the 4-day estrous cycle. Female preference for male volatile odors over those from females was observed on each day of their estrous cycle, including estrus. Moreover, following gonadectomy (Experiment 3) female hamsters still preferred male volatile odors to those of females. Taken together, this suggests that circulating levels of gonadal hormones do not influence preference for male volatile odors in female hamsters. PMID:17374544

(Boiling water reactor (BWR) CORA experiments)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ott, L.J.

To participate in the 1990 CORA Workshop at Kernforschungszentrum Karlsruhe (KfK) GmbH, Karlsruhe, FRG, on October 1--4, and to participate in detailed discussions on October 5 with the KfK CORA Boiling Water Reactor (BWR) experiments. The traveler attended the 1990 CORA Workshop at KfK, FRG. Participation included the presentation of a paper on work performed by the Boiling Water Reactor Core Melt Progression Phenomena Program at Oak Ridge National Laboratory (ORNL) on posttest analyses of CORA BWR experiments. The Statement of Work (November 1989) for the BWR Core Melt Progression Phenomena Program provides for pretest and posttest analyses of themore » BWR CORA experiments performed at KfK. Additionally, it is intended that ORNL personnel participate in the planning process for future CORA BWR experiments. For these purposes, meetings were held with KfK staff to discuss such topics as (1) experimental test schedule, (2) BWR test conduct, (3) perceived BWR experimental needs, and (4) KfK operational staff needs with respect to ORNL support. 19 refs.« less

Comparison of High-Performance Fiber Materials Properties in Simulated and Actual Space Environments

NASA Technical Reports Server (NTRS)

Finckernor, M. M.

2017-01-01

A variety of high-performance fibers, including Kevlar, Nomex, Vectran, and Spectra, have been tested for durability in the space environment, mostly the low Earth orbital environment. These materials have been tested in yarn, tether/cable, and fabric forms. Some material samples were tested in a simulated space environment, such as the Atomic Oxygen Beam Facility and solar simulators in the laboratory. Other samples were flown on the International Space Station as part of the Materials on International Space Station Experiment. Mass loss due to atomic oxygen erosion and optical property changes due to ultraviolet radiation degradation are given. Tensile test results are also presented, including where moisture loss in a vacuum had an impact on tensile strength.

NASDA next-generation aquatic habitat for space shuttle and ISS

NASA Astrophysics Data System (ADS)

Masukawa, M.; Ochiai, T.; Kamigaichi, S.; Uchida, S.; Kono, Y.; Takamatsu, T.; Sakimura, T.

The National Space Development Agency of Japan (NASDA) has more than 20 years of experience developing aquatic animal experiment facilities. These include the Vestibular Function Experiment Unit (VFEU), Aquatic Animal Experiment Unit (AAEU) and another VFEU for marine fish. Each facility had functions such as life support for up to 15 days, water quality control system, gas exchange by artificial lung, video observation through a window by a crewmember, day/night cycle control, feeding system for medaka (AAEU only), and more. We are now studying the next -generation aquatic animal experiment facility or the Aquatic Habitat (AQH) for both Space Shuttle and Space Station use. AQH will have many new capabilities missing in earlier facilities. The following functions are of particular importance: long-term life support for up to 90 days, multigeneration breeding (for medaka and zebrafish), automatic feeding system adaptable for young of fish and amphibians, water quality control for long-term experiments, air-water interface, a computer-driven specimen-monitoring system housed in the facilities, and a specimen sampling system including eggs. A prototype breeding system and the specimen-monitoring system were designed and tested. The prototype breeding system consists of a closed water loop, two 700ml fish chambers with LED lighting, a small artificial lung, and a nitrification bacteria filter. Medaka adult fish were able to mate and spawn in this small breeding system, and the young could grow to adult fish. The water quality control system also worked successfully. For amphibians, the breeding test using tadpoles of xenopus is also starting. We have many difficult technological problems to resolve, but development of AQH is going well. In this paper, we will introduce the results of the component-level test and the concept of AQH. In the future, many space biological experiments will be conducted, especially in the areas of developmental biology, neurophisiology, and the effect of microgravity over multiple generations, through the use of aquatic animals and AQH.

Water: A Sticky Subject?

ERIC Educational Resources Information Center

McCarty, Robbie V.

2000-01-01

Introduces an activity for fifth grade elementary students on water, cohesion, and adhesion. Provides a list of necessary materials and includes a checklist for performance based assessment. Recommends follow up experiments for testing cohesive property with different liquids. (YDS)

Apollo Soyuz Mission: 5-Day Report

NASA Technical Reports Server (NTRS)

1975-01-01

The Apollo Soyuz Test Project mission objectives and technical investigations are summarized. Topics discussed include: spacecraft and crew systems performance; joint flight activities; scientific and applications experiments; in-flight demonstrations; biomedical considerations; and mission support performance.

Science Notes.

ERIC Educational Resources Information Center

School Science Review, 1984

1984-01-01

Presents 26 activities, experiments, demonstrations, games, and computer programs for biology, chemistry, and physics. Background information, laboratory procedures, equipment lists, and instructional strategies are given. Topics include eye measurements, nutrition, soil test tube rack, population dynamics, angular momentum, transition metals,…

The 1986 Goddard Space Flight Center Battery Workshop

NASA Technical Reports Server (NTRS)

Morrow, George W. (Editor); Yi, Thomas Y. (Editor)

1987-01-01

The subjects covered include: lithium cell technology and safety improvements; nickel-cadmium separator and electrode technology along with associated modifications; flight experience and life testing of nickel-cadmium cell; and nickel-hydrogen applications and technology.

Auditory effects of noise on air-crew personnel.

DOT National Transportation Integrated Search

1972-11-01

Hearing-threshold tests were made on flight personnel of several sorts, including aerial-application pilots, flight instructors, private pilots, stewardesses, and FAA flight inspectors. Excluding those people whose flight experience is of short durat...

Tested Studies for Laboratory Teaching. Proceedings of the Workshop/Conference of the Association for Biology Laboratory Education (ABLE) (12th, Springfield, Missouri, June 4-8, 1990). Volume 12.

ERIC Educational Resources Information Center

Goldman, Corey A., Ed.

The focus of the Association for Biology Laboratory Education (ABLE) is to improve the undergraduate biology laboratory experience by promoting the development and dissemination of interesting, innovative, and reliable laboratory exercises. This proceedings volume includes 13 papers: "Non-Radioactive DNA Hybridization Experiments for the…

Some new tests at the Gottingen laboratory

NASA Technical Reports Server (NTRS)

1921-01-01

The tests at the Gottingen laboratory included: friction tests on a surface treated with omelette, verification tests on the M.V.A. 356 wing, and comparative tests of wing no. 36 at the Eiffel laboratory. The examination of all these experiments leads to the belief that, at large incidences, the speeds registered by the suction manometer of the testing chamber of the Eiffel laboratory wind tunnel are, owing to pressure drop, greater than the actual speeds. Therefore, the values of k(sub x) and k(sub y) measured at the Eiffel laboratory at large incidences are too low.

Space Software Defined Radio Characterization to Enable Reuse

NASA Technical Reports Server (NTRS)

Mortensen, Dale J.; Bishop, Daniel W.; Chelmins, David

2012-01-01

NASA's Space Communication and Navigation Testbed is beginning operations on the International Space Station this year. The objective is to promote new software defined radio technologies and associated software application reuse, enabled by this first flight of NASA's Space Telecommunications Radio System architecture standard. The Space Station payload has three software defined radios onboard that allow for a wide variety of communications applications; however, each radio was only launched with one waveform application. By design the testbed allows new waveform applications to be uploaded and tested by experimenters in and outside of NASA. During the system integration phase of the testbed special waveform test modes and stand-alone test waveforms were used to characterize the SDR platforms for the future experiments. Characterization of the Testbed's JPL SDR using test waveforms and specialized ground test modes is discussed in this paper. One of the test waveforms, a record and playback application, can be utilized in a variety of ways, including new satellite on-orbit checkout as well as independent on-board testbed experiments.

Engineering of beam direct conversion for a 120-kV, 1-MW ion beam

NASA Technical Reports Server (NTRS)

Barr, W. L.; Doggett, J. N.; Hamilton, G. W.; Kinney, J. D.; Moir, R. W.

1977-01-01

Practical systems for beam direct conversion are required to recover the energy from ion beams at high efficiency and at very high beam power densities in the environment of a high-power neutral-injection system. Such an experiment is now in progress using a 120-kV beam with a maximum total current of 20 A. After neutralization, the H(+) component to be recovered will have a power of approximately 1 MW. A system testing these concepts has been designed and tested at 15 kV, 2 kW in preparation for the full-power tests. The engineering problems involved in the full-power tests affect electron suppression, gas pumping, voltage holding, diagnostics, and measurement conditions. Planning for future experiments at higher power includes the use of cryopumping and electron suppression by a magnetic field rather than by an electrostatic field. Beam direct conversion for large fusion experiments and reactors will save millions of dollars in the cost of power supplies and electricity and will dispose of the charged beam under conditions that may not be possible by other techniques.

Cryogenic Two-Phase Flight Experiment: Results overview

NASA Technical Reports Server (NTRS)

Swanson, T.; Buchko, M.; Brennan, P.; Bello, M.; Stoyanof, M.

1995-01-01

This paper focuses on the flight results of the Cryogenic Two-Phase Flight Experiment (CRYOTP), which was a Hitchhiker based experiment that flew on the space shuttle Columbia in March of 1994 (STS-62). CRYOTP tested two new technologies for advanced cryogenic thermal control; the Space Heat Pipe (SHP), which was a constant conductance cryogenic heat pipe, and the Brilliant Eyes Thermal Storage Unit (BETSU), which was a cryogenic phase-change thermal storage device. These two devices were tested independently during the mission. Analysis of the flight data indicated that the SHP was unable to start in either of two attempts, for reasons related to the fluid charge, parasitic heat leaks, and cryocooler capacity. The BETSU test article was successfully operated with more than 250 hours of on-orbit testing including several cooldown cycles and 56 freeze/thaw cycles. Some degradation was observed with the five tactical cryocoolers used as thermal sinks, and one of the cryocoolers failed completely after 331 hours of operation. Post-flight analysis indicated that this problem was most likely due to failure of an electrical controller internal to the unit.

Stability and Control Estimation Flight Test Results for the SR-71 Aircraft With Externally Mounted Experiments

NASA Technical Reports Server (NTRS)

Moes, Timothy R.; Iliff, Kenneth

2002-01-01

A maximum-likelihood output-error parameter estimation technique is used to obtain stability and control derivatives for the NASA Dryden Flight Research Center SR-71A airplane and for configurations that include experiments externally mounted to the top of the fuselage. This research is being done as part of the envelope clearance for the new experiment configurations. Flight data are obtained at speeds ranging from Mach 0.4 to Mach 3.0, with an extensive amount of test points at approximately Mach 1.0. Pilot-input pitch and yaw-roll doublets are used to obtain the data. This report defines the parameter estimation technique used, presents stability and control derivative results, and compares the derivatives for the three configurations tested. The experimental configurations studied generally show acceptable stability, control, trim, and handling qualities throughout the Mach regimes tested. The reduction of directional stability for the experimental configurations is the most significant aerodynamic effect measured and identified as a design constraint for future experimental configurations. This report also shows the significant effects of aircraft flexibility on the stability and control derivatives.

Mathematical anxiety is linked to reduced cognitive reflection: a potential road from discomfort in the mathematics classroom to susceptibility to biases

PubMed Central

2014-01-01

Background When asked to solve mathematical problems, some people experience anxiety and threat, which can lead to impaired mathematical performance (Curr Dir Psychol Sci 11:181–185, 2002). The present studies investigated the link between mathematical anxiety and performance on the cognitive reflection test (CRT; J Econ Perspect 19:25–42, 2005). The CRT is a measure of a person’s ability to resist intuitive response tendencies, and it correlates strongly with important real-life outcomes, such as time preferences, risk-taking, and rational thinking. Methods In Experiments 1 and 2 the relationships between maths anxiety, mathematical knowledge/mathematical achievement, test anxiety and cognitive reflection were analysed using mediation analyses. Experiment 3 included a manipulation of working memory load. The effects of anxiety and working memory load were analysed using ANOVAs. Results Our experiments with university students (Experiments 1 and 3) and secondary school students (Experiment 2) demonstrated that mathematical anxiety was a significant predictor of cognitive reflection, even after controlling for the effects of general mathematical knowledge (in Experiment 1), school mathematical achievement (in Experiment 2) and test anxiety (in Experiments 1–3). Furthermore, Experiment 3 showed that mathematical anxiety and burdening working memory resources with a secondary task had similar effects on cognitive reflection. Conclusions Given earlier findings that showed a close link between cognitive reflection, unbiased decisions and rationality, our results suggest that mathematical anxiety might be negatively related to individuals’ ability to make advantageous choices and good decisions. PMID:25179230

Technology for advanced liquefaction processes: Coal/waste coprocessing studies

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cugini, A.V.; Rothenberger, K.S.; Ciocco, M.V.

1995-12-31

The efforts in this project are directed toward three areas: (1) novel catalyst (supported and unsupported) research and development, (2) study and optimization of major operating parameters (specifically pressure), and (3) coal/waste coprocessing. The novel catalyst research and development activity has involved testing supported catalysts, dispersed catalysts, and use of catalyst testing units to investigate the effects of operating parameters (the second area) with both supported and unsupported catalysts. Several supported catalysts were tested in a simulated first stage coal liquefaction application at 404{degrees}C during this performance period. A Ni-Mo hydrous titanate catalyst on an Amocat support prepared by Sandiamore » National laboratories was tested. Other baseline experiments using AO-60 and Amocat, both Ni-Mo/Al{sub 2}O{sub 3} supported catalysts, were also made. These experiments were short duration (approximately 12 days) and monitored the initial activity of the catalysts. The results of these tests indicate that the Sandia catalyst performed as well as the commercially prepared catalysts. Future tests are planned with other Sandia preparations. The dispersed catalysts tested include sulfated iron oxide, Bayferrox iron oxide (iron oxide from Miles, Inc.), and Bailey iron oxide (micronized iron oxide from Bailey, Inc.). The effects of space velocity, temperature, and solvent-to-coal ratio on coal liquefaction activity with the dispersed catalysts were investigated. A comparison of the coal liquefaction activity of these catalysts relative to iron catalysts tested earlier, including FeOOH-impregnated coal, was made. These studies are discussed.« less

Investigation of reliability attributes and accelerated stress factors of terrestrial solar cells. First annual report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Prince, J.L.; Lathrop, J.W.

1979-05-01

The results of accelerated stress testing of four different types of silicon terrestrial solar cells are discussed. The accelerated stress tests used included bias-temperature tests, bias-temperature-humidity tests, thermal cycle and thermal shock tests, and power cycle tests. Characterization of the cells was performed before stress testing and at periodic down-times, using electrical measurement, visual inspection, and metal adherence pull tests. Electrical parameters measured included short-circuit current, I/sub sc/, open circuit voltage, V/sub oc/, and output power, voltage, and current at the maximum power point, P/sub m/, V/sub m/, and I/sub m/ respectively. Incorporated in the report are the distributions ofmore » the prestress electrical data for all cell types. Data was also obtained on cell series and shunt resistance. Significant differences in the response to the various stress tests was observed between cell types. On the basis of the experience gained in this research work, a suggested Reliability Qualification Test Schedule was developed.« less

Institutional and structural barriers to HIV testing: elements for a theoretical framework.

PubMed

Meyerson, Beth; Barnes, Priscilla; Emetu, Roberta; Bailey, Marlon; Ohmit, Anita; Gillespie, Anthony

2014-01-01

Stigma is a barrier to HIV health seeking, but little is known about institutional and structural expressions of stigma in HIV testing. This study examines evidence of institutional and structural stigma in the HIV testing process. A qualitative, grounded theory study was conducted using secondary data from a 2011 HIV test site evaluation data in a Midwestern, moderate HIV incidence state. Expressions of structural and institutional stigma were found with over half of the testing sites and at three stages of the HIV testing visit. Examples of structural stigma included social geography, organization, and staff behavior at first encounter and reception, and staff behavior when experiencing the actual HIV test. Institutional stigma was socially expressed through staff behavior at entry/reception and when experiencing the HIV test. The emerging elements demonstrate the potential compounding of stigma experiences with deleterious effect. Study findings may inform future development of a theoretical framework. In practice, findings can guide organizations seeking to reduce HIV testing barriers, as they provide a window into how test seekers experience HIV test sites at first encounter, entry/reception, and at testing stages; and can identify how stigma might be intensified by structural and institutional expressions.

Study of a 3×3 module array of the ECAL0 calorimeter with an electron beam at the ELSA

NASA Astrophysics Data System (ADS)

Dziewiecki, M.; Anfimov, N.; Anosov, V.; Barth, J.; Chalyshev, V.; Chirikov-Zorin, I.; Elsner, D.; Frolov, V.; Frommberger, F.; Guskov, A.; Klein, F.; Krumshteyn, Z.; Kurjata, R.; Marzec, J.; Nagaytsev, A.; Olchevski, A.; Orlov, I.; Rybnikov, A.; Rychter, A.; Selyunin, A.; Zaremba, K.; Ziembicki, M.

2015-02-01

ECAL0 is a new electromagnetic calorimeter designed for studying generalized parton distributions at the COMPASS II experiment at CERN. It will be located next to the target and will cover larger photon angles (up to 30 degrees). It is a modular high-granularity Shashlyk device with total number of individual channels of approx. 1700 and readout based on wavelength shifting fibers and micropixel avalanche photodiodes. Characterization of the calorimeter includes tests of particular sub-components, tests of complete modules and module arrays, as well as a pilot run of a fully-functional, quarter-size prototype in the COMPASS experiment. The main goals of the tests on low-intensity electron beam at the ELSA accelerator in Bonn were: to provide energy calibration using electrons, to measure angular response of the calorimeter and to perform an energy scan to cross-check previously collected data. A dedicated measurement setup was prepared for the tests, including a 3x3 array of the ECAL0 modules, a scintillating-fibre hodoscope and a remotely-controlled motorized movable platform. The measurements were performed using three electron energies: 3.2 GeV, 1.6 GeV and 0.8 GeV. They include a calibration of the whole detector array with a straight beam and multiple angular scans.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dykstra, Dave; Garzoglio, Gabriele; Kim, Hyunwoo

As of 2012, a number of US Department of Energy (DOE) National Laboratories have access to a 100 Gb/s wide-area network backbone. The ESnet Advanced Networking Initiative (ANI) project is intended to develop a prototype network, based on emerging 100 Gb/s Ethernet technology. The ANI network will support DOE's science research programs. A 100 Gb/s network test bed is a key component of the ANI project. The test bed offers the opportunity for early evaluation of 100Gb/s network infrastructure for supporting the high impact data movement typical of science collaborations and experiments. In order to make effective use of thismore » advanced infrastructure, the applications and middleware currently used by the distributed computing systems of large-scale science need to be adapted and tested within the new environment, with gaps in functionality identified and corrected. As a user of the ANI test bed, Fermilab aims to study the issues related to end-to-end integration and use of 100 Gb/s networks for the event simulation and analysis applications of physics experiments. In this paper we discuss our findings from evaluating existing HEP Physics middleware and application components, including GridFTP, Globus Online, etc. in the high-speed environment. These will include possible recommendations to the system administrators, application and middleware developers on changes that would make production use of the 100 Gb/s networks, including data storage, caching and wide area access.« less

Relativity time-delay experiments utilizing 'Mariner' spacecraft

NASA Technical Reports Server (NTRS)

Esposito, P. B.; Anderson, J. D.

1974-01-01

Relativity predicts that the transit time of a signal propagated from the earth to a spacecraft and retransmitted back to earth ought to exhibit an additional, variable time delay. The present work describes some of the analytical techniques employed in experiments using Mariner spacecraft designed to test the accuracy of this prediction. Two types of data are analyzed in these relativity experiments; these include phase-coherent, two-way Doppler shift and round-trip, transit-time measurements. Results of Mariner 6 and 7 relativistic time-delay experiments are in agreement with Einstein's theory of general relativity with an uncertainty of 3%.

ALSEP termination report

NASA Technical Reports Server (NTRS)

Bates, J. R.; Lauderdale, W. W.; Kernaghan, H.

1979-01-01

The Apollo Lunar Surface Experiments Package (ALSEP) final report was prepared when support operations were terminated September 30, 1977, and NASA discontinued the receiving and processing of scientific data transmitted from equipment deployed on the lunar surface. The ALSEP experiments (Apollo 11 to Apollo 17) are described and pertinent operational history is given for each experiment. The ALSEP data processing and distribution are described together with an extensive discussion on archiving. Engineering closeout tests and results are given, and the status and configuration of the experiments at termination are documented. Significant science findings are summarized by selected investigators. Significant operational data and recommendations are also included.

Oxidation and gum formation in diesel fuels. Interim technical report, May-December 1985

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mayo, F.R.

1985-12-20

This Report describes experiments on oxidation and gum formation from n-dodecane, tetralin, and several diesel fuels at 43, 60, and 100 C, with and without added initiators, t-butyl peroxide and 2,2'azobis(2-methylpropionitrile) (ABN). Experiments on gum determination and a manuscript for publication, Gum and Deposit Formation from Jet Turbine and Diesel Fuels at 100 C, are included. One objective of work on this Contract is to relate oxidations of diesel fuels at 100 and 130 C, where experiments can be performed in hours or days, to standard tests for fuel stability at ambient temperatures and 43.3 C (110 F), which requiremore » many weeks. A second objective is to devise a fast test for fuel stability.« less

Angular response calibration of the burst and transient source experiment

NASA Technical Reports Server (NTRS)

Lestrade, John Patrick

1988-01-01

The Gamma Ray Observatory includes four experiments designed to observe the gamma-ray universe. Laboratory measurements to test the response the Burst and Transient Source Experiment (BATSE) modules to gamma-ray sources that are non-axial were recently completed. The results of these observations are necessary for the correct interpretation of BATSE data obtained after it is put in Earth orbit. The launch is planned for March, 1900. Preliminary analyses of these test data show the presence of a radial dependence to the detector's light collection efficiency. It is proposed to evaluate the importance of this radial response, analyze future experimental data to derive the actual functional dependence on radius, and calculate the net effect on the output spectrum as a function of the angle of incidence.

Stereotypes influence false memories for imagined events.

PubMed

Kleider, Heather M; Goldinger, Stephen D; Knuycky, Leslie

2008-02-01

Two experiments tested the influences of vivid imagery and person schemata on eyewitness accuracy. Participants watched an event sequence including actors performing stereotype-consistent and inconsistent actions. Additionally, participants either read descriptions of actions (Experiment 1) or vividly imagined actions (Experiment 2). After either 30 minutes or 2 days, recognition memory, source memory, and remember/know judgements were made. After 2 days, false alarms to imagined events increased, relative to the 30-minute test; those false alarms were more often misattributed to stereotype-consistent actors, relative to the same actions in the reading condition. In addition, the accompanying remember judgements were higher for false alarms to imagined events, relative to read events, regardless of stereotype consistency. Overall the results suggest that, over time, vivid imagery reinforces schema activation, increasing stereotype-consistent false memories.

Design and Qualification of the AMS-02 Flight Cryocoolers

NASA Technical Reports Server (NTRS)

Shirey, Kimberly; Banks,Stuart; Boyle, Rob; Unger, Reuven

2005-01-01

Four commercial Sunpower M87N Stirling-cycle cryocoolers will be used to extend the lifetime of the Alpha Magnetic Spectrometer-02 (AMS-02) experiment. The cryocoolers will be mounted to the AMS-02 vacuum case using a structure that will thermally and mechanically decouple the cryocooler from the vacuum case. This paper discusses modifications of the Sunpower M87N cryocooler to make it acceptable for space flight applications and suitable for use on AMS-02. Details of the flight model qualification test program are presented. AMS-02 is a state-of-the-art particle physics detector containing a large superfluid helium-cooled superconducting magnet. Highly sensitive detector plates inside the magnet measure a particle's speed, mass, charge, and direction. The AMS-02 experiment, which will be flown as an attached payload on the International Space Station, will study the properties and origin of cosmic particles and nuclei including antimatter and dark matter. Two engineering model cryocoolers have been under test at NASA Goddard since November 2001. Qualification testing of the engineering model cryocooler bracket assembly including random vibration and thermal vacuum testing was completed at the end of April 2005. The flight cryocoolers were received in December 2003. Acceptance testing of the flight cryocooler bracket assemblies began in May 2005 .

Experimental determination of in situ utilization of lunar regolith for thermal energy storage

NASA Technical Reports Server (NTRS)

Richter, Scott W.

1992-01-01

A Lunar Thermal Energy from Regolith (LUTHER) experiment has been designed and fabricated at the NASA Lewis Research Center to determine the feasibility of using lunar soil as thermal energy storage media. The experimental apparatus includes an alumina ceramic canister which contains simulated lunar regolith, a heater, nine heat shields, a heat transfer cold jacket, and 19 type-B platinum rhodium thermocouples. The simulated lunar regolith is a basalt that closely resembles the lunar basalt returned to earth by the Apollo missions. The experiment will test the effects of vacuum, particle size, and density on the thermophysical properties of the regolith, which include melt temperature, specific heat thermal conductivity, and latent heat of storage. Two separate tests, using two different heaters, will be performed to study the effect of heating the system using radiative and conductive heat transfer. A finite differencing SINDA model was developed at NASA Lewis Research Center to predict the performance of the LUTHER experiment. The code will predict the effects of vacuum, particle size, and density has on the heat transfer to the simulated regolith.

Space Shuttle Projects

NASA Image and Video Library

1985-11-30

The crew assigned to the STS-61B mission included Bryan D. O’Conner, pilot; Brewster H. Shaw, commander; Charles D. Walker, payload specialist; mission specialists Jerry L. Ross, Mary L. Cleave, and Sherwood C. Spring; and Rodolpho Neri Vela, payload specialist. Launched aboard the Space Shuttle Atlantis November 28, 1985 at 7:29:00 pm (EST), the STS-61B mission’s primary payload included three communications satellites: MORELOS-B (Mexico); AUSSAT-2 (Australia); and SATCOM KU-2 (RCA Americom). Two experiments were conducted to test assembling erectable structures in space: EASE (Experimental Assembly of Structures in Extravehicular Activity), and ACCESS (Assembly Concept for Construction of Erectable Space Structure). In a joint venture between NASA/Langley Research Center in Hampton, Virginia and the Marshall Space Flight Center (MSFC), EASE and ACCESS were developed and demonstrated at MSFC's Neutral Buoyancy Simulator (NBS). The primary objective of this experiment was to test the structural assembly concepts for suitability as the framework for larger space structures and to identify ways to improve the productivity of space construction. In this STS-61B onboard photo, astronaut Ross was working on the ACCESS experiment during an Extravehicular Activity (EVA).

Critical Analysis of Primary Literature in a Master’s-Level Class: Effects on Self-Efficacy and Science-Process Skills

PubMed Central

Abdullah, Christopher; Parris, Julian; Lie, Richard; Guzdar, Amy; Tour, Ella

2015-01-01

The ability to think analytically and creatively is crucial for success in the modern workforce, particularly for graduate students, who often aim to become physicians or researchers. Analysis of the primary literature provides an excellent opportunity to practice these skills. We describe a course that includes a structured analysis of four research papers from diverse fields of biology and group exercises in proposing experiments that would follow up on these papers. To facilitate a critical approach to primary literature, we included a paper with questionable data interpretation and two papers investigating the same biological question yet reaching opposite conclusions. We report a significant increase in students’ self-efficacy in analyzing data from research papers, evaluating authors’ conclusions, and designing experiments. Using our science-process skills test, we observe a statistically significant increase in students’ ability to propose an experiment that matches the goal of investigation. We also detect gains in interpretation of controls and quantitative analysis of data. No statistically significant changes were observed in questions that tested the skills of interpretation, inference, and evaluation. PMID:26250564

NASA's Zero-g aircraft operations

NASA Technical Reports Server (NTRS)

Williams, R. K.

1988-01-01

NASA's Zero-g aircraft, operated by the Johnson Space Center, provides the unique weightless or zero-g environment of space flight for hardware development and test and astronaut training purposes. The program, which began in 1959, uses a slightly modified Boeing KC-135A aircraft, flying a parabolic trajectory, to produce weightless periods of 20 to 25 seconds. The program has supported the Mercury, Gemini, Apollo, Skylab, Apollo-Soyuz and Shuttle programs as well as a number of unmanned space operations. Typical experiments for flight in the aircraft have included materials processing experiments, welding, fluid manipulation, cryogenics, propellant tankage, satellite deployment dynamics, planetary sciences research, crew training with weightless indoctrination, space suits, tethers, etc., and medical studies including vestibular research. The facility is available to microgravity research organizations on a cost-reimbursable basis, providing a large, hands-on test area for diagnostic and support equipment for the Principal Investigators and providing an iterative-type design approach to microgravity experiment development. The facility allows concepts to be proven and baseline experimentation to be accomplished relatively inexpensively prior to committing to the large expense of a space flight.

From Cooks to Carpenters: Measuring - A Saleable Work Skill. Occupation Simulation Packet. Grades 5th-6th.

ERIC Educational Resources Information Center

Kennedy, Helena

This teacher's guide contains simulated work experiences for 5th and 6th grade students using the isolated skill concept - measuring. Teacher instructions include objectives, evaluation, and sequence of activities. The guide contains pre-tests and post-tests with instructions and answer keys. Three pre-skill activities are suggested, such as…