Single-side conduction modeling for high heat flux coolant channels

DOE Office of Scientific and Technical Information (OSTI.GOV)

Boyd, R.D. Sr.

In the development of plasma-facing components (PFCs), most investigators have erroneously postulated negligible water critical heat flux dependence on the coolant channel length-to-diameter (L/D) ratio above a constant value of L/D. Although encouraging results have been obtained in characterizing peaking factors for local two-dimensional boiling curves and critical heat flux, additional experimental data and theoretical model development are needed to validate the applicability to PFCs. Both these and related issues will affect the flow boiling correlation and data reduction associated with the development of PFCs for fusion reactors and other physical problems that are dependent on conduction modeling in themore » heat flux spectrum of applications. Both exact solutions and numerical conjugate analyses are presented for a one-side heated (OSH) geometry. The results show (a) the coexistence of three flow regimes inside an OSH circular geometry, (b) the correlational dependence of the inside wall heat flux and temperature, and (c) inaccuracies that could arise in some data reduction procedures.« less

RACLETTE: a model for evaluating the thermal response of plasma facing components to slow high power plasma transients. Part II: Analysis of ITER plasma facing components

NASA Astrophysics Data System (ADS)

Federici, Gianfranco; Raffray, A. René

1997-04-01

The transient thermal model RACLETTE (acronym of Rate Analysis Code for pLasma Energy Transfer Transient Evaluation) described in part I of this paper is applied here to analyse the heat transfer and erosion effects of various slow (100 ms-10 s) high power energy transients on the actively cooled plasma facing components (PFCs) of the International Thermonuclear Experimental Reactor (ITER). These have a strong bearing on the PFC design and need careful analysis. The relevant parameters affecting the heat transfer during the plasma excursions are established. The temperature variation with time and space is evaluated together with the extent of vaporisation and melting (the latter only for metals) for the different candidate armour materials considered for the design (i.e., Be for the primary first wall, Be and CFCs for the limiter, Be, W, and CFCs for the divertor plates) and including for certain cases low-density vapour shielding effects. The critical heat flux, the change of the coolant parameters and the possible severe degradation of the coolant heat removal capability that could result under certain conditions during these transients, for example for the limiter, are also evaluated. Based on the results, the design implications on the heat removal performance and erosion damage of the variuos ITER PFCs are critically discussed and some recommendations are made for the selection of the most adequate protection materials and optimum armour thickness.

Development of visible spectroscopy diagnostics for W sources assessment in WEST

NASA Astrophysics Data System (ADS)

Meyer, O.; Jones, O. M.; Giacalone, J. C.; Pascal, J. Y.; Raulin, D.; Xu, H.; Aumeunier, M. H.; Baude, R.; Escarguel, A.; Gil, C.; Harris, J. H.; Hatchressian, J.-C.; Klepper, C. C.; Larroque, S.; Lotte, Ph.; Moreau, Ph.; Pégourié, B.; Vartanian, S.

2016-11-01

The present work concerns the development of a W sources assessment system in the framework of the tungsten-W environment in steady state tokamak project that aims at equipping the existing Tore Supra device with a tungsten divertor in order to test actively cooled tungsten Plasma Facing Components (PFCs) in view of preparing ITER operation. The goal is to assess W sources and D recycling with spectral, spatial, and temporal resolution adapted to the PFCs observed. The originality of the system is that all optical elements are installed in the vacuum vessel and compatible with steady state operation. Our system is optimized to measure radiance as low as 1016 Ph/(m2 s sr). A total of 240 optical fibers will be deployed to the detection systems such as the "Filterscope," developed by Oak Ridge National Laboratory (USA) and consisting of photomultiplier tubes and filters, or imaging spectrometers dedicated to Multiview analysis.

Baseline high heat flux and plasma facing materials for fusion

NASA Astrophysics Data System (ADS)

Ueda, Y.; Schmid, K.; Balden, M.; Coenen, J. W.; Loewenhoff, Th.; Ito, A.; Hasegawa, A.; Hardie, C.; Porton, M.; Gilbert, M.

2017-09-01

In fusion reactors, surfaces of plasma facing components (PFCs) are exposed to high heat and particle flux. Tungsten and Copper alloys are primary candidates for plasma facing materials (PFMs) and coolant tube materials, respectively, mainly due to high thermal conductivity and, in the case of tungsten, its high melting point. In this paper, recent understandings and future issues on responses of tungsten and Cu alloys to fusion environments (high particle flux (including T and He), high heat flux, and high neutron doses) are reviewed. This review paper includes; Tritium retention in tungsten (K. Schmid and M. Balden), Impact of stationary and transient heat loads on tungsten (J.W. Coenen and Th. Loewenhoff), Helium effects on surface morphology of tungsten (Y. Ueda and A. Ito), Neutron radiation effects in tungsten (A. Hasegawa), and Copper and copper alloys development for high heat flux components (C. Hardie, M. Porton, and M. Gilbert).

Plasma-wall interaction studies within the EUROfusion consortium: progress on plasma-facing components development and qualification

NASA Astrophysics Data System (ADS)

Brezinsek, S.; Coenen, J. W.; Schwarz-Selinger, T.; Schmid, K.; Kirschner, A.; Hakola, A.; Tabares, F. L.; van der Meiden, H. J.; Mayoral, M.-L.; Reinhart, M.; Tsitrone, E.; Ahlgren, T.; Aints, M.; Airila, M.; Almaviva, S.; Alves, E.; Angot, T.; Anita, V.; Arredondo Parra, R.; Aumayr, F.; Balden, M.; Bauer, J.; Ben Yaala, M.; Berger, B. M.; Bisson, R.; Björkas, C.; Bogdanovic Radovic, I.; Borodin, D.; Bucalossi, J.; Butikova, J.; Butoi, B.; Čadež, I.; Caniello, R.; Caneve, L.; Cartry, G.; Catarino, N.; Čekada, M.; Ciraolo, G.; Ciupinski, L.; Colao, F.; Corre, Y.; Costin, C.; Craciunescu, T.; Cremona, A.; De Angeli, M.; de Castro, A.; Dejarnac, R.; Dellasega, D.; Dinca, P.; Dittmar, T.; Dobrea, C.; Hansen, P.; Drenik, A.; Eich, T.; Elgeti, S.; Falie, D.; Fedorczak, N.; Ferro, Y.; Fornal, T.; Fortuna-Zalesna, E.; Gao, L.; Gasior, P.; Gherendi, M.; Ghezzi, F.; Gosar, Ž.; Greuner, H.; Grigore, E.; Grisolia, C.; Groth, M.; Gruca, M.; Grzonka, J.; Gunn, J. P.; Hassouni, K.; Heinola, K.; Höschen, T.; Huber, S.; Jacob, W.; Jepu, I.; Jiang, X.; Jogi, I.; Kaiser, A.; Karhunen, J.; Kelemen, M.; Köppen, M.; Koslowski, H. R.; Kreter, A.; Kubkowska, M.; Laan, M.; Laguardia, L.; Lahtinen, A.; Lasa, A.; Lazic, V.; Lemahieu, N.; Likonen, J.; Linke, J.; Litnovsky, A.; Linsmeier, Ch.; Loewenhoff, T.; Lungu, C.; Lungu, M.; Maddaluno, G.; Maier, H.; Makkonen, T.; Manhard, A.; Marandet, Y.; Markelj, S.; Marot, L.; Martin, C.; Martin-Rojo, A. B.; Martynova, Y.; Mateus, R.; Matveev, D.; Mayer, M.; Meisl, G.; Mellet, N.; Michau, A.; Miettunen, J.; Möller, S.; Morgan, T. W.; Mougenot, J.; Mozetič, M.; Nemanič, V.; Neu, R.; Nordlund, K.; Oberkofler, M.; Oyarzabal, E.; Panjan, M.; Pardanaud, C.; Paris, P.; Passoni, M.; Pegourie, B.; Pelicon, P.; Petersson, P.; Piip, K.; Pintsuk, G.; Pompilian, G. O.; Popa, G.; Porosnicu, C.; Primc, G.; Probst, M.; Räisänen, J.; Rasinski, M.; Ratynskaia, S.; Reiser, D.; Ricci, D.; Richou, M.; Riesch, J.; Riva, G.; Rosinski, M.; Roubin, P.; Rubel, M.; Ruset, C.; Safi, E.; Sergienko, G.; Siketic, Z.; Sima, A.; Spilker, B.; Stadlmayr, R.; Steudel, I.; Ström, P.; Tadic, T.; Tafalla, D.; Tale, I.; Terentyev, D.; Terra, A.; Tiron, V.; Tiseanu, I.; Tolias, P.; Tskhakaya, D.; Uccello, A.; Unterberg, B.; Uytdenhoven, I.; Vassallo, E.; Vavpetič, P.; Veis, P.; Velicu, I. L.; Vernimmen, J. W. M.; Voitkans, A.; von Toussaint, U.; Weckmann, A.; Wirtz, M.; Založnik, A.; Zaplotnik, R.; PFC contributors, WP

2017-11-01

The provision of a particle and power exhaust solution which is compatible with first-wall components and edge-plasma conditions is a key area of present-day fusion research and mandatory for a successful operation of ITER and DEMO. The work package plasma-facing components (WP PFC) within the European fusion programme complements with laboratory experiments, i.e. in linear plasma devices, electron and ion beam loading facilities, the studies performed in toroidally confined magnetic devices, such as JET, ASDEX Upgrade, WEST etc. The connection of both groups is done via common physics and engineering studies, including the qualification and specification of plasma-facing components, and by modelling codes that simulate edge-plasma conditions and the plasma-material interaction as well as the study of fundamental processes. WP PFC addresses these critical points in order to ensure reliable and efficient use of conventional, solid PFCs in ITER (Be and W) and DEMO (W and steel) with respect to heat-load capabilities (transient and steady-state heat and particle loads), lifetime estimates (erosion, material mixing and surface morphology), and safety aspects (fuel retention, fuel removal, material migration and dust formation) particularly for quasi-steady-state conditions. Alternative scenarios and concepts (liquid Sn or Li as PFCs) for DEMO are developed and tested in the event that the conventional solution turns out to not be functional. Here, we present an overview of the activities with an emphasis on a few key results: (i) the observed synergistic effects in particle and heat loading of ITER-grade W with the available set of exposition devices on material properties such as roughness, ductility and microstructure; (ii) the progress in understanding of fuel retention, diffusion and outgassing in different W-based materials, including the impact of damage and impurities like N; and (iii), the preferential sputtering of Fe in EUROFER steel providing an in situ W surface and a potential first-wall solution for DEMO.

Plasma–wall interaction studies within the EUROfusion consortium: progress on plasma-facing components development and qualification

DOE PAGES

Brezinsek, S.; Coenen, J. W.; Schwarz-Selinger, T.; ...

2017-06-14

The provision of a particle and power exhaust solution which is compatible with first-wall components and edge-plasma conditions is a key area of present-day fusion research and mandatory for a successful operation of ITER and DEMO. The work package plasma-facing components (WP PFC) within the European fusion programme complements with laboratory experiments, i.e. in linear plasma devices, electron and ion beam loading facilities, the studies performed in toroidally confined magnetic devices, such as JET, ASDEX Upgrade, WEST etc. The connection of both groups is done via common physics and engineering studies, including the qualification and specification of plasma-facing components, andmore » by modelling codes that simulate edge-plasma conditions and the plasma–material interaction as well as the study of fundamental processes. WP PFC addresses these critical points in order to ensure reliable and efficient use of conventional, solid PFCs in ITER (Be and W) and DEMO (W and steel) with respect to heat-load capabilities (transient and steady-state heat and particle loads), lifetime estimates (erosion, material mixing and surface morphology), and safety aspects (fuel retention, fuel removal, material migration and dust formation) particularly for quasi-steady-state conditions. Alternative scenarios and concepts (liquid Sn or Li as PFCs) for DEMO are developed and tested in the event that the conventional solution turns out to not be functional. Here, we present an overview of the activities with an emphasis on a few key results: (i) the observed synergistic effects in particle and heat loading of ITER-grade W with the available set of exposition devices on material properties such as roughness, ductility and microstructure; (ii) the progress in understanding of fuel retention, diffusion and outgassing in different W-based materials, including the impact of damage and impurities like N; and (iii), the preferential sputtering of Fe in EUROFER steel providing an in situ W surface and a potential first-wall solution for DEMO.« less

Plasma–wall interaction studies within the EUROfusion consortium: progress on plasma-facing components development and qualification

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brezinsek, S.; Coenen, J. W.; Schwarz-Selinger, T.

The provision of a particle and power exhaust solution which is compatible with first-wall components and edge-plasma conditions is a key area of present-day fusion research and mandatory for a successful operation of ITER and DEMO. The work package plasma-facing components (WP PFC) within the European fusion programme complements with laboratory experiments, i.e. in linear plasma devices, electron and ion beam loading facilities, the studies performed in toroidally confined magnetic devices, such as JET, ASDEX Upgrade, WEST etc. The connection of both groups is done via common physics and engineering studies, including the qualification and specification of plasma-facing components, andmore » by modelling codes that simulate edge-plasma conditions and the plasma–material interaction as well as the study of fundamental processes. WP PFC addresses these critical points in order to ensure reliable and efficient use of conventional, solid PFCs in ITER (Be and W) and DEMO (W and steel) with respect to heat-load capabilities (transient and steady-state heat and particle loads), lifetime estimates (erosion, material mixing and surface morphology), and safety aspects (fuel retention, fuel removal, material migration and dust formation) particularly for quasi-steady-state conditions. Alternative scenarios and concepts (liquid Sn or Li as PFCs) for DEMO are developed and tested in the event that the conventional solution turns out to not be functional. Here, we present an overview of the activities with an emphasis on a few key results: (i) the observed synergistic effects in particle and heat loading of ITER-grade W with the available set of exposition devices on material properties such as roughness, ductility and microstructure; (ii) the progress in understanding of fuel retention, diffusion and outgassing in different W-based materials, including the impact of damage and impurities like N; and (iii), the preferential sputtering of Fe in EUROFER steel providing an in situ W surface and a potential first-wall solution for DEMO.« less

Plasma-Facing Component and Materials Testing for the NSTX-U

NASA Astrophysics Data System (ADS)

Jaworski, Michael; Brooks, A.; Gerhardt, S.; Loesser, D.; Mardenfeld, M.; Menard, J.; Gray, T.; Reinke, M.

2017-10-01

The NSTX-U Recovery Project is developing plasma-facing components for use in the divertor of NSTX-U. The extreme conditions of the NSTX-U divertor make it possible to stress even graphite surfaces to the material limits leading to the possibility of component failures. In addition, the complex, mixed-material environment of the NSTX-U due to the use of boron and lithium wall conditioning techniques creates significant uncertainties in the monitoring of the PFCs. A testing program has been developed to inform on the material and design limitations of the NSTX-U high-heat flux components. These tests include high-heat flux testing in electron beam facilities as well as plasma-based testing. The NSTX-U components could experience perpendicular heat fluxes as high as 45 MW/m2. Parallel heat fluxes onto leading edges could reach 475 MW/m2. The testing program and material survey plan will be presented. Work supported by DOE contract DE-AC02-09CH11466 and DE-AC05-00OR22725.

Overview of the recent DiMES and MiMES experiments in DIII-D

NASA Astrophysics Data System (ADS)

Rudakov, D. L.; Wong, C. P. C.; Litnovsky, A.; Wampler, W. R.; Boedo, J. A.; Brooks, N. H.; Fenstermacher, M. E.; Groth, M.; Hollmann, E. M.; Jacob, W.; Krasheninnikov, S. I.; Krieger, K.; Lasnier, C. J.; Leonard, A. W.; McLean, A. G.; Marot, M.; Moyer, R. A.; Petrie, T. W.; Philipps, V.; Smirnov, R. D.; Stangeby, P. C.; Watkins, J. G.; West, W. P.; Yu, J. H.

2009-12-01

Divertor and midplane material evaluation systems (DiMES and MiMES) in the DIII-D tokamak are used to address a variety of plasma-material interaction (PMI) issues relevant to ITER. Among the topics studied are carbon erosion and re-deposition, hydrogenic retention in the gaps between plasma-facing components (PFCs), deterioration of diagnostic mirrors from carbon deposition and techniques to mitigate that deposition, and dynamics and transport of dust. An overview of the recent experimental results is presented.

Design and Demonstration of a Material-Plasma Exposure Target Station for Neutron Irradiated Samples

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rapp, Juergen; Aaron, A. M.; Bell, Gary L.

2015-10-20

Fusion energy is the most promising energy source for the future, and one of the most important problems to be solved progressing to a commercial fusion reactor is the identification of plasma-facing materials compatible with the extreme conditions in the fusion reactor environment. The development of plasma–material interaction (PMI) science and the technology of plasma-facing components are key elements in the development of the next step fusion device in the United States, the so-called Fusion Nuclear Science Facility (FNSF). All of these PMI issues and the uncertain impact of the 14-MeV neutron irradiation have been identified in numerous expert panelmore » reports to the fusion community. The 2007 Greenwald report classifies reactor plasma-facing materials (PFCs) and materials as the only Tier 1 issues, requiring a “. . . major extrapolation from the current state of knowledge, need for qualitative improvements and substantial development for both the short and long term.” The Greenwald report goes on to list 19 gaps in understanding and performance related to the plasma–material interface for the technology facilities needed for DEMO-oriented R&D and DEMO itself. Of the 15 major gaps, six (G7, G9, G10, G12, G13) can possibly be addressed with ORNL’s proposal of an advanced Material Plasma Exposure eXperiment. Establishing this mid-scale plasma materials test facility at ORNL is a key element in ORNL’s strategy to secure a leadership role for decades of fusion R&D. That is to say, our end goal is to bring the “signature facility” FNSF home to ORNL. This project is related to the pre-conceptual design of an innovative target station for a future Material–Plasma Exposure eXperiment (MPEX). The target station will be designed to expose candidate fusion reactor plasma-facing materials and components (PFMs and PFCs) to conditions anticipated in fusion reactors, where PFCs will be exposed to dense high-temperature hydrogen plasmas providing steady-state heat fluxes of 5–20 MW/m 2 and ion fluxes up to 10 24 m -2s -1. Since PFCs will have to withstand neutron irradiation displacement damage up to 50 dpa, the target station design must accommodate radioactive specimens (materials to be irradiated in HFIR or at SNS) to enable investigations of the impact of neutron damage on materials. Therefore, the system will have to be able to install and extract irradiated specimens using equipment and methods to avoid sample modification, control contamination, and minimize worker dose. Included in the design considerations will be an assessment of all the steps between neutron irradiation and post-exposure materials examination/characterization, as well as an evaluation of the facility hazard categorization. In particular, the factors associated with the acquisition of radioactive specimens and their preparation, transportation, experimental configuration at the plasma-specimen interface, post-plasma-exposure sample handling, and specimen preparation will be evaluated. Neutronics calculations to determine the dose rates of the samples were carried out for a large number of potential plasma-facing materials.« less

Influence of the first wall material on the particle fuelling in ASDEX Upgrade

NASA Astrophysics Data System (ADS)

Lunt, T.; Reimold, F.; Wolfrum, E.; Carralero, D.; Feng, Y.; Schmid, K.; the ASDEX Upgrade Team

2017-05-01

In the period from 2002 to 2007 the material of the plasma facing components (PFCs) of ASDEX Upgrade (AUG) was changed from carbon (C) to tungsten (W). Comparing the measured density profiles of low-density L-mode discharges with little or no gas puff before and after this modification, a significantly higher pedestal-top density was found for W PFCs together with a steeper gradient and a lower pedestal temperature. This change can be explained by larger particle- and energy reflection coefficients for D on W compared to D on C, as shown by EMC3-EIRENE simulations of AUG discharges in similar conditions on a computational grid extending to the main chamber first wall. In the simulations, a change of the wall material at fixed separatrix density indeed shows that for W PFCs more neutrals cross the separatrix, resulting in a steeper density gradient. Analysis of the source resolved and poloidally resolved neutral flux densities across the separatrix show a dominant contribution of the divertor targets to the fuelling profile in the simulation of the low density case. Increasing the density decreases the electron temperature at the target and therefore the potential drop in the electrostatic sheath as well as the energy of the ions impinging on the surface. Neutrals with ∼eV energies, able to reach the separatrix, are then only produced via molecular dissociation processes in the plasma volume independently of the PFC material. Also the contribution of the main chamber PFCs to the fuelling is observed to increase at higher densities.

Material Surface Characteristics and Plasma Performance in the Lithium Tokamak Experiment

NASA Astrophysics Data System (ADS)

Lucia, Matthew James

The performance of a tokamak plasma and the characteristics of the surrounding plasma facing component (PFC) material surfaces strongly influence each other. Despite this relationship, tokamak plasma physics has historically been studied more thoroughly than PFC surface physics. The disparity is particularly evident in lithium PFC research: decades of experiments have examined the effect of lithium PFCs on plasma performance, but the understanding of the lithium surface itself is much less complete. This latter information is critical to identifying the mechanisms by which lithium PFCs affect plasma performance. This research focused on such plasma-surface interactions in the Lithium Tokamak Experiment (LTX), a spherical torus designed to accommodate solid or liquid lithium as the primary PFC. Surface analysis was accomplished via the novel Materials Analysis and Particle Probe (MAPP) diagnostic system. In a series of experiments on LTX, the MAPP x-ray photoelectron spectroscopy (XPS) and thermal desorption spectroscopy (TDS) capabilities were used for in vacuo interrogation of PFC samples. This represented the first application of XPS and TDS for in situ surface analysis of tokamak PFCs. Surface analysis indicated that the thin (dLi ˜ 100nm) evaporative lithium PFC coatings in LTX were converted to Li2O due to oxidizing agents in both the residual vacuum and the PFC substrate. Conversion was rapid and nearly independent of PFC temperature, forming a majority Li2O surface within minutes and an entirely Li2O surface within hours. However, Li2O PFCs were still capable of retaining hydrogen and sequestering impurities until the Li2 O was further oxidized to LiOH, a process that took weeks. For hydrogen retention, Li2O PFCs retained H+ from LTX plasma discharges, but no LiH formation was observed. Instead, results implied that H+ was only weakly-bound, such that it almost completely outgassed as H 2 within minutes. For impurity sequestration, LTX plasma performance---ascertained from plasma current and density measurements---progressively improved as plasma carbon and oxygen impurity levels fell. This was true for PFC conditioning by vacuum baking and argon glow discharge cleaning, as well as by lithium evaporation. Some evidence suggested that impurity sequestration was more important than hydrogen retention in enhancing LTX plasma performance. In contrast with expectations for lithium PFCs, heating the Li2 O PFCs in LTX caused increased plasma impurity levels that tended to reduce plasma performance.

Occurrence and source apportionment of Per- and poly-fluorinated compounds (PFCs) in North Canal Basin, Beijing

PubMed Central

Zhang, Yi-Zhe; Wang, Bin; Wang, Wei; Li, Wen-Chao; Huang, Jun; Deng, Shu-Bo; Wang, Yu-Jue; Yu, Gang

2016-01-01

Various per- and poly-fluorinated compounds (PFCs) were first systematically investigated in North Canal Basin, Beijing, China. A total of 68 surface water samples were collected from North Canal Basin, Beijing, at high spatial resolution. The seasonal disparity was compared and associated with source variation. PFCs concentrations in low-water period ranged from 26 to 207 ng/L, and significantly declined levels were found in high-water period. The individual component proportions among different sites varied less in high-water period, when runoff played a role in mixing and diluting PFCs. A methodology combined with principal component analysis (PCA), heat map-hierarchical cluster analysis (HM-HCA), and correlation analysis were introduced to discriminate sources of PFCs in surface water. The statistical results agreed with each other, and daily domestic consumption, fire-fighting products and related industries were identified as sources of PFCs in this region. In addition, two composition ratios were proposed through the methodology to distinguish the impact of nonpoint source, and the outcome demonstrates that great disparities exist in compositional profiles between nonpoint source and others. Overall, the results showed that this comprehensive analysis method has great potential for source apportionment in surface water and other environmental compartments. PMID:27845351

Conceptual design of a pre-loaded liquid lithium divertor target for NSTX-U

DOE PAGES

Rindt, P.; Lopes Cardozo, N. J.; van Dommelen, J. A. W.; ...

2016-09-03

In this study, a conceptual design for a pre-filled liquid lithium divertor target for the National Spherical Torus Experiment Upgrade (NSTX-U) is presented. The design is aimed at facilitating experiments with high lithium flux from the plasma facing components (PFCs) in NSTX-U and investigating the potential of capillary based liquid lithium components. In the design, lithium is supplied from a reservoir in the PFC to the plasma facing surface via capillary action in a wicking structure. This working principle is also demonstrated experimentally. Next, a titanium zirconium molybdenum (TZM) prototype design is presented, required to withstand a steady state heatmore » flux peaking at 10 MW m –2 for 5 s and edge localized modes depositing (130 kJ in 2 ms at 10 Hz). The main challenge is to sufficiently reduce the thermal stresses. This is achieved by dividing the surface into brushes and filling the slots in between with liquid lithium. The principle of using this liquid “interlayer” allows for thermal expansion and simultaneously heat conduction, and could be used to significantly reduce the demands to solids in future PFCs. Lithium flow to the surface is analyzed using a novel analytical model, ideally suited for design purposes. Thermal stresses in the PFC are analyzed using the finite element method. As a result, the requirements are met, and thus a prototype will be manufactured for physical testing.« less

Conceptual design of a pre-loaded liquid lithium divertor target for NSTX-U

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rindt, P.; Lopes Cardozo, N. J.; van Dommelen, J. A. W.

In this study, a conceptual design for a pre-filled liquid lithium divertor target for the National Spherical Torus Experiment Upgrade (NSTX-U) is presented. The design is aimed at facilitating experiments with high lithium flux from the plasma facing components (PFCs) in NSTX-U and investigating the potential of capillary based liquid lithium components. In the design, lithium is supplied from a reservoir in the PFC to the plasma facing surface via capillary action in a wicking structure. This working principle is also demonstrated experimentally. Next, a titanium zirconium molybdenum (TZM) prototype design is presented, required to withstand a steady state heatmore » flux peaking at 10 MW m –2 for 5 s and edge localized modes depositing (130 kJ in 2 ms at 10 Hz). The main challenge is to sufficiently reduce the thermal stresses. This is achieved by dividing the surface into brushes and filling the slots in between with liquid lithium. The principle of using this liquid “interlayer” allows for thermal expansion and simultaneously heat conduction, and could be used to significantly reduce the demands to solids in future PFCs. Lithium flow to the surface is analyzed using a novel analytical model, ideally suited for design purposes. Thermal stresses in the PFC are analyzed using the finite element method. As a result, the requirements are met, and thus a prototype will be manufactured for physical testing.« less

First operation with the JET International Thermonuclear Experimental Reactor-like walla)

NASA Astrophysics Data System (ADS)

Neu, R.; Arnoux, G.; Beurskens, M.; Bobkov, V.; Brezinsek, S.; Bucalossi, J.; Calabro, G.; Challis, C.; Coenen, J. W.; de la Luna, E.; de Vries, P. C.; Dux, R.; Frassinetti, L.; Giroud, C.; Groth, M.; Hobirk, J.; Joffrin, E.; Lang, P.; Lehnen, M.; Lerche, E.; Loarer, T.; Lomas, P.; Maddison, G.; Maggi, C.; Matthews, G.; Marsen, S.; Mayoral, M.-L.; Meigs, A.; Mertens, Ph.; Nunes, I.; Philipps, V.; Pütterich, T.; Rimini, F.; Sertoli, M.; Sieglin, B.; Sips, A. C. C.; van Eester, D.; van Rooij, G.; JET-EFDA Contributors

2013-05-01

To consolidate International Thermonuclear Experimental Reactor (ITER) design choices and prepare for its operation, Joint European Torus (JET) has implemented ITER's plasma facing materials, namely, Be for the main wall and W in the divertor. In addition, protection systems, diagnostics, and the vertical stability control were upgraded and the heating capability of the neutral beams was increased to over 30 MW. First results confirm the expected benefits and the limitations of all metal plasma facing components (PFCs) but also yield understanding of operational issues directly relating to ITER. H-retention is lower by at least a factor of 10 in all operational scenarios compared to that with C PFCs. The lower C content (≈ factor 10) has led to much lower radiation during the plasma burn-through phase eliminating breakdown failures. Similarly, the intrinsic radiation observed during disruptions is very low, leading to high power loads and to a slow current quench. Massive gas injection using a D2/Ar mixture restores levels of radiation and vessel forces similar to those of mitigated disruptions with the C wall. Dedicated L-H transition experiments indicate a 30% power threshold reduction, a distinct minimum density, and a pronounced shape dependence. The L-mode density limit was found to be up to 30% higher than for C allowing stable detached divertor operation over a larger density range. Stable H-modes as well as the hybrid scenario could be re-established only when using gas puff levels of a few 1021 es-1. On average, the confinement is lower with the new PFCs, but nevertheless, H factors up to 1 (H-Mode) and 1.3 (at βN≈3, hybrids) have been achieved with W concentrations well below the maximum acceptable level.

First Operation with the JET ITER-Like Wall

NASA Astrophysics Data System (ADS)

Neu, Rudolf

2012-10-01

To consolidate ITER design choices and prepare for its operation, JET has implemented ITER's plasma facing materials, namely Be at the main wall and W in the divertor. In addition, protection systems, diagnostics and the vertical stability control were upgraded and the heating capability of the neutral beams was increased to over 30 MW. First results confirm the expected benefits and the limitations of all metal plasma facing components (PFCs), but also yield understanding of operational issues directly relating to ITER. H-retention is lower by at least a factor of 10 in all operational scenarios compared to that with C PFCs. The lower C content (˜ factor 10) have led to much lower radiation during the plasma burn-through phase eliminating breakdown failures. Similarly, the intrinsic radiation observed during disruptions is very low, leading to high power loads and to a slow current quench. Massive gas injection using a D2/Ar mixture restores levels of radiation and vessel forces similar to those of mitigated disruptions with the C wall. Dedicated L-H transition experiments indicate a reduced power threshold by 30%, a distinct minimum density and pronounced shape dependence. The L-mode density limit was found up to 30% higher than for C allowing stable detached divertor operation over a larger density range. Stable H-modes as well as the hybrid scenario could be only re-established when using gas puff levels of a few 10^21e/s. On average the confinement is lower with the new PFCs, but nevertheless, H factors around 1 (H-Mode) and 1.2 (at βN˜3, Hybrids) have been achieved with W concentrations well below the maximum acceptable level (<10-5).

Design, Manufacture, and Experimental Serviceability Validation of ITER Blanket Components

NASA Astrophysics Data System (ADS)

Leshukov, A. Yu.; Strebkov, Yu. S.; Sviridenko, M. N.; Safronov, V. M.; Putrik, A. B.

2017-12-01

In 2014, the Russian Federation and the ITER International Organization signed two Procurement Arrangements (PAs) for ITER blanket components: 1.6.P1ARF.01 "Blanket First Wall" of February 14, 2014, and 1.6.P3.RF.01 "Blanket Module Connections" of December 19, 2014. The first PA stipulates development, manufacture, testing, and delivery to the ITER site of 179 Enhanced Heat Flux (EHF) First Wall (FW) Panels intended for withstanding the heat flux from the plasma up to 4.7MW/m2. Two Russian institutions, NIIEFA (Efremov Institute) and NIKIET, are responsible for the implementation of this PA. NIIEFA manufactures plasma-facing components (PFCs) of the EHF FW panels and performs the final assembly and testing of the panels, and NIKIET manufactures FW beam structures, load-bearing structures of PFCs, and all elements of the panel attachment system. As for the second PA, NIKIET is the sole official supplier of flexible blanket supports, electrical insulation key pads (EIKPs), and blanket module/vacuum vessel electrical connectors. Joint activities of NIKIET and NIIEFA for implementing PA 1.6.P1ARF.01 are briefly described, and information on implementation of PA 1.6.P3.RF.01 is given. Results of the engineering design and research efforts in the scope of the above PAs in 2015-2016 are reported, and results of developing the technology for manufacturing ITER blanket components are presented.

Divertor scenario development for NSTX Upgrade

NASA Astrophysics Data System (ADS)

Soukhanovskii, V. A.; McLean, A. G.; Meier, E. T.; Rognlien, T. D.; Ryutov, D. D.; Bell, R. E.; Diallo, A.; Gerhardt, S. P.; Kaita, R.; Kolemen, E.; Leblanc, B. P.; Menard, J. E.; Podesta, M.; Scotti, F.

2012-10-01

In the NSTX-U tokamak, initial plans for divertor plasma-facing components (PFCs) include lithium and boron coated graphite, with a staged transition to molybdenum. Steady-state peak divertor heat fluxes are projected to reach 20-30 MW/m^2 in 2 MA, 12 MW NBI-heated discharges of up to 5 s duration, thus challenging PFC thermal limits. Based on the recent NSTX divertor experiments and modeling with edge transport code UEDGE, a favorable basis for divertor power handling in NSTX-U is developed. The snowflake divertor geometry and feedback-controlled divertor impurity seeding applied to the lower and upper divertors are presently envisioned. In the NSTX snowflake experiments with lithium-coated graphite PFCs, the peak divertor heat fluxes from Type I ELMs and between ELMs were significantly reduced due to geometry effects, increased volumetric losses and null-point convective redistribution between strike points. H-mode core confinement was maintained at H98(y,2)<=1 albeit the radiative detachment. Additional CD4 seeding demonstrated potential for a further increase of divertor radiation.

Development of visible spectroscopy diagnostics for W sources assessment in WEST

DOE Office of Scientific and Technical Information (OSTI.GOV)

Meyer, O., E-mail: olivier.meyer@cea.fr; Giacalone, J. C.; Pascal, J. Y.

2016-11-15

The present work concerns the development of a W sources assessment system in the framework of the tungsten-W environment in steady state tokamak project that aims at equipping the existing Tore Supra device with a tungsten divertor in order to test actively cooled tungsten Plasma Facing Components (PFCs) in view of preparing ITER operation. The goal is to assess W sources and D recycling with spectral, spatial, and temporal resolution adapted to the PFCs observed. The originality of the system is that all optical elements are installed in the vacuum vessel and compatible with steady state operation. Our system ismore » optimized to measure radiance as low as 10{sup 16} Ph/(m{sup 2} s sr). A total of 240 optical fibers will be deployed to the detection systems such as the “Filterscope,” developed by Oak Ridge National Laboratory (USA) and consisting of photomultiplier tubes and filters, or imaging spectrometers dedicated to Multiview analysis.« less

Effects of in situ dual ion beam (He+ and D+) irradiation with simultaneous pulsed heat loading on surface morphology evolution of tungsten-tantalum alloys

NASA Astrophysics Data System (ADS)

Gonderman, S.; Tripathi, J. K.; Sinclair, G.; Novakowski, T. J.; Sizyuk, T.; Hassanein, A.

2018-02-01

The strong thermal and mechanical properties of tungsten (W) are well suited for the harsh fusion environment. However, increasing interest in using tungsten as plasma-facing components (PFCs) has revealed several key issues. These potential roadblocks necessitate more investigation of W and other alternative W based materials exposed to realistic fusion conditions. In this work, W and tungsten-tantalum (W-Ta) alloys were exposed to single (He+) and dual (He+  +  D+) ion irradiations with simultaneous pulsed heat loading to elucidate PFCs response under more realistic conditions. Laser only exposer revealed significantly more damage in W-Ta samples as compared to pure W samples. This was due to the difference in the mechanical properties of the two different materials. Further erosion studies were conducted to evaluate the material degradation due to transient heat loading in both the presence and absence of He+ and/or D+ ions. We concluded that erosion of PFC materials was significantly enhanced due to the presence of ion irradiation. This is important as it demonstrates that there are key synergistic effects resulting from more realistic fusion loading conditions that need to be considered when evaluating the response of plasma facing materials.

The Effects of Temperature and Oxidation on Deuterium Retention in Solid and Liquid Lithium Films on Molybdenum Plasma-Facing Components

NASA Astrophysics Data System (ADS)

Capece, Angela

2014-10-01

Liquid metal plasma-facing components (PFCs) enable in-situ renewal of the surface, thereby offering a solution to neutron damage, erosion, and thermal fatigue experienced by solid PFCs. Lithium in particular has a high chemical affinity for hydrogen, which has resulted in reduced recycling and enhanced plasma performance on many fusion devices including TFTR, T11-M, FTU, CDX-U, LTX, TJ-II, and NSTX. A key component to the improvement in plasma performance is deuterium retention in Li; however, this process is not well understood in the complex tokamak environment. Recent surface science experiments conducted at the Princeton Plasma Physics Laboratory have used electron spectroscopy and temperature programmed desorption to understand the mechanisms for D retention in Li coatings on Mo substrates. The experiments were designed to give monolayer-control of Li films and were conducted in ultrahigh vacuum under controlled environments. An electron cyclotron resonance plasma source was used to deliver a beam of deuterium ions to the surface over a range of ion energies. Our work shows that D is retained as LiD in metallic Li films. However, when oxygen is present in the film, either by diffusion from the subsurface at high temperature or as a contaminant during the deposition process, Li oxides are formed that retain D as LiOD. Experiments indicate that LiD is more thermally stable than LiOD, which decomposes to liberate D2 gas and D2O at temperatures 100 K lower than the LiD decomposition temperature. Other experiments show how D retention varies with substrate temperature to provide insight into the differences between solid and liquid lithium films. This work was supported by DOE Contract No. DE AC02-09CH11466.

Dependence of LTX plasma performance on surface conditions as determined by in situ analysis of plasma facing components

NASA Astrophysics Data System (ADS)

Lucia, M.; Kaita, R.; Majeski, R.; Bedoya, F.; Allain, J. P.; Abrams, T.; Bell, R. E.; Boyle, D. P.; Jaworski, M. A.; Schmitt, J. C.

2015-08-01

The Materials Analysis and Particle Probe (MAPP) diagnostic has been implemented on the Lithium Tokamak Experiment (LTX) at PPPL, providing the first in situ X-ray photoelectron spectroscopy (XPS) surface characterization of tokamak plasma facing components (PFCs). MAPP samples were exposed to argon glow discharge conditioning (GDC), lithium evaporations, and hydrogen tokamak discharges inside LTX. Samples were analyzed with XPS, and alterations to surface conditions were correlated against observed LTX plasma performance changes. Argon GDC caused the accumulation of nm-scale metal oxide layers on the PFC surface, which appeared to bury surface carbon and oxygen contamination and thus improve plasma performance. Lithium evaporation led to the rapid formation of a lithium oxide (Li2O) surface; plasma performance was strongly improved for sufficiently thick evaporative coatings. Results indicate that a 5 h argon GDC or a 50 nm evaporative lithium coating will both significantly improve LTX plasma performance.

Material Surface Characteristics and Plasma Performance in the Lithium Tokamak Experiment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lucia, Matthew James

The performance of a tokamak plasma and the characteristics of the surrounding plasma facing component (PFC) material surfaces strongly influence each other. Despite this relationship, tokamak plasma physics has historically been studied more thoroughly than PFC surface physics. The disparity is particularly evident in lithium PFC research: decades of experiments have examined the effect of lithium PFCs on plasma performance, but the understanding of the lithium surface itself is much less complete. This latter information is critical to identifying the mechanisms by which lithium PFCs affect plasma performance. This research focused on such plasma-surface interactions in the Lithium Tokamak Experimentmore » (LTX), a spherical torus designed to accommodate solid or liquid lithium as the primary PFC. Surface analysis was accomplished via the novel Materials Analysis and Particle Probe (MAPP) diagnostic system. In a series of experiments on LTX, the MAPP x-ray photoelectron spectroscopy (XPS) and thermal desorption spectroscopy (TDS) capabilities were used for in vacuo interrogation of PFC samples. This represented the first application of XPS and TDS for in situ surface analysis of tokamak PFCs. Surface analysis indicated that the thin (d ~ 100nm) evaporative lithium PFC coatings in LTX were converted to Li2O due to oxidizing agents in both the residual vacuum and the PFC substrate. Conversion was rapid and nearly independent of PFC temperature, forming a majority Li2O surface within minutes and an entirely Li2O surface within hours. However, Li2O PFCs were still capable of retaining hydrogen and sequestering impurities until the Li2O was further oxidized to LiOH, a process that took weeks. For hydrogen retention, Li2O PFCs retained H+ from LTX plasma discharges, but no LiH formation was observed. Instead, results implied that H+ was only weakly-bound, such that it almost completely outgassed as H2 within minutes. For impurity sequestration, LTX plasma performance—ascertained from plasma current and density measurements—progressively improved as plasma carbon and oxygen impurity levels fell. This was true for PFC conditioning by vacuum baking and argon glow discharge cleaning, as well as by lithium evaporation. Some evidence suggested that impurity sequestration was more important than hydrogen retention in enhancing LTX plasma performance. In contrast with expectations for lithium PFCs, heating the Li2O PFCs in LTX caused increased plasma impurity levels that tended to reduce plasma performance.« less

RACLETTE: a model for evaluating the thermal response of plasma facing components to slow high power plasma transients. Part I: Theory and description of model capabilities

NASA Astrophysics Data System (ADS)

Raffray, A. René; Federici, Gianfranco

1997-04-01

RACLETTE (Rate Analysis Code for pLasma Energy Transfer Transient Evaluation), a comprehensive but relatively simple and versatile model, was developed to help in the design analysis of plasma facing components (PFCs) under 'slow' high power transients, such as those associated with plasma vertical displacement events. The model includes all the key surface heat transfer processes such as evaporation, melting, and radiation, and their interaction with the PFC block thermal response and the coolant behaviour. This paper represents part I of two sister and complementary papers. It covers the model description, calibration and validation, and presents a number of parametric analyses shedding light on and identifying trends in the PFC armour block response to high plasma energy deposition transients. Parameters investigated include the plasma energy density and deposition time, the armour thickness and the presence of vapour shielding effects. Part II of the paper focuses on specific design analyses of ITER plasma facing components (divertor, limiter, primary first wall and baffle), including improvements in the thermal-hydraulic modeling required for better understanding the consequences of high energy deposition transients in particular for the ITER limiter case.

Measurements of W Erosion using UV Emission from DIII-D and CTH

NASA Astrophysics Data System (ADS)

Johnson, Curtis; Ennis, David; Loch, Stuart; Balance, Connor; Victor, Brian; Allen, Steve; Samuell, Cameron; Abrams, Tyler; Unterberg, Ezekial

2017-10-01

of Plasma Facing Components (PFCs) will play a critical role in establishing the performance of reactor-relevant fusion devices, particularly for tungsten (W) divertor targets. Erosion can be diagnosed from spectral line emission together with atomic coefficients representing the `ionizations per photon' (S/XB). Emission from W I is most intense in the UV region. Thus, UV survey spectrometers (200-400 nm) are used to diagnose W PFCs erosion in the DIII-D divertor and from a W tipped probe in the CTH experiment. Nineteen W emission lines in the UV region are identified between the two experiments, allowing for multiple S/XB erosion measurements. Initial W erosion measurements are compared to erosion using the 400.9 nm W I line. Complete UV spectra will be presented and compared to synthetic spectra for varying plasma conditions. Analysis of the metastable states impact on the S/XB will be presented as well as possible electron temperature and density diagnosis from W I line ratios. Work supported by USDOE Grants DE-SC0015877 & DE-FC02-04ER54698.

He bubble growth and interaction in W nano-tendrils

NASA Astrophysics Data System (ADS)

Smirnov, R. D.; Krasheninnikov, S. I.

2015-11-01

Tungsten plasma-facing components (PFCs) in fusion devices are exposed to variety of extreme plasma conditions, which can lead to alteration of tungsten micro-structure and degradation of the PFCs. In particular, it is known that filamentary nano-structures called fuzz can grow on helium plasma exposed tungsten surfaces. However, mechanism of the fuzz growth is still not fully understood. Existing experimental observations indicate that formation of helium nano-bubbles in tungsten plays essential role in fuzz formation and growth. In this work we investigate mechanisms of growth and interaction of helium bubbles in fuzz-like nano-tendrils using molecular dynamics simulations with LAMMPS code. We show that growth of the bubbles has anisotropic character producing complex stress field in the nano-tendrils with distinct compression and tension regions. We found that formation of large inter-bubble tension regions can cause lateral stretching and bending of the tendrils that consequently lead to their elongation and thinning at the stretching sites. The rate of nano-tendril growth due to the described mechanism is also evaluated from the simulations.

ELM mitigation with pellet ELM triggering and implications for PFCs and plasma performance in ITER

DOE Office of Scientific and Technical Information (OSTI.GOV)

Baylor, Larry R.; Lang, P.; Allen, S. L.

2015-08-01

The triggering of rapid small edge localized modes (ELMs) by high frequency pellet injection has been proposed as a method to prevent large naturally occurring ELMs that can erode the ITER plasma facing components (PFCs). Deuterium pellet injection has been used to successfully demonstrate the on-demand triggering of edge localized modes (ELMs) at much higher rates and with much smaller intensity than natural ELMs. The proposed hypothesis for the triggering mechanism of ELMs by pellets is the local pressure perturbation resulting from reheating of the pellet cloud that can exceed the local high-n ballooning mode threshold where the pellet ismore » injected. Nonlinear MHD simulations of the pellet ELM triggering show destabilization of high-n ballooning modes by such a local pressure perturbation.A review of the recent pellet ELM triggering results from ASDEX Upgrade (AUG), DIII-D, and JET reveals that a number of uncertainties about this ELM mitigation technique still remain. These include the heat flux impact pattern on the divertor and wall from pellet triggered and natural ELMs, the necessary pellet size and injection location to reliably trigger ELMs, and the level of fueling to be expected from ELM triggering pellets and synergy with larger fueling pellets. The implications of these issues for pellet ELM mitigation in ITER and its impact on the PFCs are presented along with the design features of the pellet injection system for ITER.« less

The EPQ Code System for Simulating the Thermal Response of Plasma-Facing Components to High-Energy Electron Impact

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ward, Robert Cameron; Steiner, Don

2004-06-15

The generation of runaway electrons during a thermal plasma disruption is a concern for the safe and economical operation of a tokamak power system. Runaway electrons have high energy, 10 to 300 MeV, and may potentially cause extensive damage to plasma-facing components (PFCs) through large temperature increases, melting of metallic components, surface erosion, and possible burnout of coolant tubes. The EPQ code system was developed to simulate the thermal response of PFCs to a runaway electron impact. The EPQ code system consists of several parts: UNIX scripts that control the operation of an electron-photon Monte Carlo code to calculate themore » interaction of the runaway electrons with the plasma-facing materials; a finite difference code to calculate the thermal response, melting, and surface erosion of the materials; a code to process, scale, transform, and convert the electron Monte Carlo data to volumetric heating rates for use in the thermal code; and several minor and auxiliary codes for the manipulation and postprocessing of the data. The electron-photon Monte Carlo code used was Electron-Gamma-Shower (EGS), developed and maintained by the National Research Center of Canada. The Quick-Therm-Two-Dimensional-Nonlinear (QTTN) thermal code solves the two-dimensional cylindrical modified heat conduction equation using the Quickest third-order accurate and stable explicit finite difference method and is capable of tracking melting or surface erosion. The EPQ code system is validated using a series of analytical solutions and simulations of experiments. The verification of the QTTN thermal code with analytical solutions shows that the code with the Quickest method is better than 99.9% accurate. The benchmarking of the EPQ code system and QTTN versus experiments showed that QTTN's erosion tracking method is accurate within 30% and that EPQ is able to predict the occurrence of melting within the proper time constraints. QTTN and EPQ are verified and validated as able to calculate the temperature distribution, phase change, and surface erosion successfully.« less

[Residue Concentration and Distribution Characteristics of Perfluorinated Compounds in Surface Water from Qiantang River in Hangzhou Section].

PubMed

Zhang, Ming; Tang, Fang-liang; Yu, Ya-yun; Xu, Jian-fen; Li, Hua; Wu, Min-hua; Zhang, Wei; Pan, Jian-yang

2015-12-01

This study studied the pollution characteristics of perfluorinated compounds (PFCs) in Qiantang River in Hangzhou section (QR). Surface water samples, collected in July 2014 and January 2015 from 14 sites in QR were analyzed for 16 PFCs. All samples were prepared by solid-phase extraction with Oasis WAX cartridges and analyzed using the ultra performance liquid chromatography interfaced to tandem mass spectrometry ( UPLC-MS/MS). The results showed that 8 medium-and short-chain PFCs including C₄ and C₈ perfluorinated sulfonates (PFSAs) and C₄-C₉ perfluorinated carboxylic acids (PFCAs) were detected in the surface waters. The total concentrations of PFCs ranged from 0.98 to 609 ng · L⁻¹, while perfluorooctanoic acid (PFOA) dominated, with range of 0.59-538 ng L⁻¹, and perfluorooctane sulfonate (PFOS) was detected at lower levels, ranging from 0 to 2.48 ng · L⁻¹. The spatial distribution of PFCs varied, and the pollutant concentrations at the sampling sites located in upstream of the river such as Lanjiangkou and Jiangjunyan were relatively high, PFCs concentration showed a decreasing trend from the upstream to the downstream. According to the ratio of feature components, PFCs in surface water of QR originated largely from the input of direct sewage emissions. Taken together, the PFCs pollution was highly correlated with the upstream of Qiantang River valley's industry distribution, and most of the mass load in the investigated river was attributed to upstream running water with a minor influence from the wastewater discharges along the river basin. Overall, the results presented here indicated that greater attention should be given to the contamination of PFCs, especially for PFOA in water body of QR.

Enhanced erosion of tungsten plasma-facing components subject to simultaneous heat pulses and deuterium plasma

NASA Astrophysics Data System (ADS)

Umstadter, K. R.; Doerner, R.; Tynan, G.

2009-04-01

When an ELM occurs in tokamaks, up to 30% of the pedestal energy can be deposited on the wall of the tokamak causing heating and material loss due to sublimation/evaporation and melt layer splashing of plasma-facing components (PFCs) and expansion of the ejected material into the plasma. A short-pulse laser system capable of reproducing the thermal load of an ELM heat pulse has been integrated into the existing PFC research program in PISCES, a laboratory facility capable of reproducing plasma-materials interactions expected during normal operation of large tokamaks. An Nd:YAG laser capable of delivering up to 1 J of energy over a 7 ns pulsewidth is used for the experiments. Laser heat pulse only, H +/D + plasma only, and laser plus plasma experiments were conducted and initial results indicate enhanced erosion of tungsten exposed to simultaneous plasma and heat pulses, as compared to exposure to separate plasma-only or heat pulse-only conditions.

Definition of acceptance criteria for the ITER divertor plasma-facing components through systematic experimental analysis

NASA Astrophysics Data System (ADS)

Escourbiac, F.; Richou, M.; Guigon, R.; Constans, S.; Durocher, A.; Merola, M.; Schlosser, J.; Riccardi, B.; Grosman, A.

2009-12-01

Experience has shown that a critical part of the high-heat flux (HHF) plasma-facing component (PFC) is the armour to heat sink bond. An experimental study was performed in order to define acceptance criteria with regards to thermal hydraulics and fatigue performance of the International Thermonuclear Experimental Reactor (ITER) divertor PFCs. This study, which includes the manufacturing of samples with calibrated artificial defects relevant to the divertor design, is reported in this paper. In particular, it was concluded that defects detectable with non-destructive examination (NDE) techniques appeared to be acceptable during HHF experiments relevant to heat fluxes expected in the ITER divertor. On the basis of these results, a set of acceptance criteria was proposed and applied to the European vertical target medium-size qualification prototype: 98% of the inspected carbon fibre composite (CFC) monoblocks and 100% of tungsten (W) monoblock and flat tiles elements (i.e. 80% of the full units) were declared acceptable.

Modeling Electrothermal Plasma with Boundary Layer Effects

NASA Astrophysics Data System (ADS)

AlMousa, Nouf Mousa A.

Electrothermal plasma sources produce high-density (1023-10 28 /m3) and high temperature (1-5 eV) plasmas that are of interest for a variety of applications such as hypervelocity launch devices, fusion reactor pellet injectors, and pulsed thrusters for small satellites. Also, the high heat flux (up to 100 GW/m2) and high pressure (100s MPa) of electrothermal (ET) plasmas allow for the use of such facilities as a source of high heat flux to simulate off-normal events in Tokamak fusion reactors. Off-normal events like disruptions, thermal and current quenches, are the perfect recipes for damage of plasma facing components (PFC). Successful operation of a fusion reactor requires comprehensive understanding of material erosion behavior. The extremely high heat fluxes deposited in PFCs melt and evaporate or directly sublime the exposed surfaces, which results in a thick vapor/melt boundary layer adjacent to the solid wall structure. The accumulating boundary layers provide a self-protecting nature by attenuating the radiant energy transport to the PFCs. The ultimate goal of this study is to develop a reliable tool to adequately simulate the effect of the boundary layers on the formation and flow of the energetic ET plasma and its impact on exposed surfaces erosion under disruption like conditions. This dissertation is a series of published journals/conferences papers. The first paper verified the existence of the vapor shield that evolved at the boundary layer under the typical operational conditions of the NC State University ET plasma facilities PIPE and SIRENS. Upon the verification of the vapor shield, the second paper proposed novel model to simulate the evolution of the boundary layer and its effectiveness in providing a self-protecting nature for the exposed plasma facing surfaces. The developed models simulate the radiant heat flux attenuation through an optically thick boundary layer. The models were validated by comparing the simulation results to experimental data taken from the ET plasma facilities. Upon validation of the boundary layer models, computational experiments were conducted with the purpose of evaluation the PFCs' erosion during plasma disruption in Tokamak fusion reactors. Erosion of a set of selected low-Z and high-Z materials were analyzed and discussed. For metallic plasma facing materials under the impact of hard and long time-scale disruption events, melting and melt-layer splashing become dominate erosion mechanisms during plasma-material interaction. In order to realistically assess the erosion of the metallic fusion reactor components, the fourth paper accounts for the various mechanisms by which material evolved from PFCs due to melting and vaporization, with a developed melting and splattering/splashing model incorporated in the ET plasma code. Also, the shielding effect associated with melt-layer and vapor-layer is investigated. The quantitative results of material erosion with the boundary layer effects including a vapor layer, melt layer and splashing effects is a new model and an important step towards achieving a better understanding of plasma-material interactions under exposure to such high heat flux conditions.

Waveguide to Core: A New Approach to RF Modelling

NASA Astrophysics Data System (ADS)

Wright, John; Shiraiwa, Syunichi; Rf-Scidac Team

2017-10-01

A new technique for the calculation of RF waves in toroidal geometry enables the simultaneous incorporation of antenna geometry, plasma facing components (PFCs), the scrape off-layer (SOL) and core propagation [Shiraiwa, NF 2017]. Calculations with this technique naturally capture wave propagation in the SOL and its interactions with non-conforming PFCs permitting self-consistent calculation of core absorption and edge power loss. The main motivating insight is that the core plasma region having closed flux surfaces requires a hot plasma dielectric while the open field line region in the scrape-off layer needs only a cold plasma dielectric. Spectral approaches work well for the former and finite elements work well for the latter. The validity of this process follows directly from the superposition principle of Maxwell's equations making this technique exact. The method is independent of the codes or representations used and works for any frequency regime. Applications to minority heating in Alcator C-Mod and ITER and high harmonic heating in NSTX-U will be presented in single pass and multi-pass regimes. Support from DoE Grant Number DE-FG02-91-ER54109 (theory and computer resources) and DE-FC02-01ER54648 (RF SciDAC).

Recrystallization and grain growth induced by ELMs-like transient heat loads in deformed tungsten samples

NASA Astrophysics Data System (ADS)

Suslova, A.; El-Atwani, O.; Sagapuram, D.; Harilal, S. S.; Hassanein, A.

2014-11-01

Tungsten has been chosen as the main candidate for plasma facing components (PFCs) due to its superior properties under extreme operating conditions in future nuclear fusion reactors such as ITER. One of the serious issues for PFCs is the high heat load during transient events such as ELMs and disruption in the reactor. Recrystallization and grain size growth in PFC materials caused by transients are undesirable changes in the material, since the isotropic microstructure developed after recrystallization exhibits a higher ductile-to-brittle transition temperature which increases with the grain size, a lower thermal shock fatigue resistance, a lower mechanical strength, and an increased surface roughening. The current work was focused on careful determination of the threshold parameters for surface recrystallization, grain growth rate, and thermal shock fatigue resistance under ELM-like transient heat events. Transient heat loads were simulated using long pulse laser beams for two different grades of ultrafine-grained tungsten. It was observed that cold rolled tungsten demonstrated better power handling capabilities and higher thermal stress fatigue resistance compared to severely deformed tungsten. Higher recrystallization threshold, slower grain growth, and lower degree of surface roughening were observed in the cold rolled tungsten.

Temperature Dependence of Lithium Reactions with Air

NASA Astrophysics Data System (ADS)

Sherrod, Roman; Skinner, C. H.; Koel, Bruce

2016-10-01

Liquid lithium plasma facing components (PFCs) are being developed to handle long pulse, high heat loads in tokamaks. Wetting by lithium of its container is essential for this application, but can be hindered by lithium oxidation by residual gases or during tokamak maintenance. Lithium PFCs will experience elevated temperatures due to plasma heat flux. This work presents measurements of lithium reactions at elevated temperatures (298-373 K) when exposed to natural air. Cylindrical TZM wells 300 microns deep with 1 cm2 surface area were filled with metallic lithium in a glovebox containing argon with less than 1.6 ppm H20, O2, and N2. The wells were transferred to a hot plate in air, and then removed periodically for mass gain measurements. Changes in the surface topography were recorded with a microscope. The mass gain of the samples at elevated temperatures followed a markedly different behavior to that at room temperature. One sample at 373 K began turning red indicative of lithium nitride, while a second turned white indicative of lithium carbonate formation. Data on the mass gain vs. temperature and associated topographic changes of the surface will be presented. Science Undergraduate Laboratory Internship funded by Department of Energy.

Recrystallization and grain growth induced by ELMs-like transient heat loads in deformed tungsten samples

PubMed Central

Suslova, A.; El-Atwani, O.; Sagapuram, D.; Harilal, S. S.; Hassanein, A.

2014-01-01

Tungsten has been chosen as the main candidate for plasma facing components (PFCs) due to its superior properties under extreme operating conditions in future nuclear fusion reactors such as ITER. One of the serious issues for PFCs is the high heat load during transient events such as ELMs and disruption in the reactor. Recrystallization and grain size growth in PFC materials caused by transients are undesirable changes in the material, since the isotropic microstructure developed after recrystallization exhibits a higher ductile-to-brittle transition temperature which increases with the grain size, a lower thermal shock fatigue resistance, a lower mechanical strength, and an increased surface roughening. The current work was focused on careful determination of the threshold parameters for surface recrystallization, grain growth rate, and thermal shock fatigue resistance under ELM-like transient heat events. Transient heat loads were simulated using long pulse laser beams for two different grades of ultrafine-grained tungsten. It was observed that cold rolled tungsten demonstrated better power handling capabilities and higher thermal stress fatigue resistance compared to severely deformed tungsten. Higher recrystallization threshold, slower grain growth, and lower degree of surface roughening were observed in the cold rolled tungsten. PMID:25366885

Recrystallization and grain growth induced by ELMs-like transient heat loads in deformed tungsten samples.

PubMed

Suslova, A; El-Atwani, O; Sagapuram, D; Harilal, S S; Hassanein, A

2014-11-04

Tungsten has been chosen as the main candidate for plasma facing components (PFCs) due to its superior properties under extreme operating conditions in future nuclear fusion reactors such as ITER. One of the serious issues for PFCs is the high heat load during transient events such as ELMs and disruption in the reactor. Recrystallization and grain size growth in PFC materials caused by transients are undesirable changes in the material, since the isotropic microstructure developed after recrystallization exhibits a higher ductile-to-brittle transition temperature which increases with the grain size, a lower thermal shock fatigue resistance, a lower mechanical strength, and an increased surface roughening. The current work was focused on careful determination of the threshold parameters for surface recrystallization, grain growth rate, and thermal shock fatigue resistance under ELM-like transient heat events. Transient heat loads were simulated using long pulse laser beams for two different grades of ultrafine-grained tungsten. It was observed that cold rolled tungsten demonstrated better power handling capabilities and higher thermal stress fatigue resistance compared to severely deformed tungsten. Higher recrystallization threshold, slower grain growth, and lower degree of surface roughening were observed in the cold rolled tungsten.

Space Station Crew Conducts Spacewalk to Change Cooling Components

NASA Image and Video Library

2018-05-16

Outside the International Space Station, Expedition 55 NASA Flight Engineers Drew Feustel and Ricky Arnold conducted a spacewalk May 16 to swap out a failed cooling system component called a pump flow control subassembly (PFCS) for a spare. The PFCS is one of several on the truss structure of the station designed to regulate the flow of ammonia coolant through the cooling loops on the station to maintain the proper temperature for critical systems. It was the 210th spacewalk in support of space station assembly, maintenance and upgrades, the eighth in Feustel’s career and the fourth for Arnold.

Armour Materials for the ITER Plasma Facing Components

NASA Astrophysics Data System (ADS)

Barabash, V.; Federici, G.; Matera, R.; Raffray, A. R.; ITER Home Teams,

The selection of the armour materials for the Plasma Facing Components (PFCs) of the International Thermonuclear Experimental Reactor (ITER) is a trade-off between multiple requirements derived from the unique features of a burning fusion plasma environment. The factors that affect the selection come primarily from the requirements of plasma performance (e.g., minimise impurity contamination in the confined plasma), engineering integrity, component lifetime (e.g., withstand thermal stresses, acceptable erosion, etc.) and safety (minimise tritium and radioactive dust inventories). The current selection in ITER is to use beryllium on the first-wall, upper baffle and on the port limiter surfaces, carbon fibre composites near the strike points of the divertor vertical target and tungsten elsewhere in the divertor and lower baffle modules. This paper provides the background for this selection vis-à-vis the operating parameters expected during normal and off-normal conditions. The reasons for the selection of the specific grades of armour materials are also described. The effects of the neutron irradiation on the properties of Be, W and carbon fibre composites at the expected ITER conditions are briefly reviewed. Critical issues are discussed together with the necessary future R&D.

Design, R&D and commissioning of EAST tungsten divertor

NASA Astrophysics Data System (ADS)

Yao, D. M.; Luo, G. N.; Zhou, Z. B.; Cao, L.; Li, Q.; Wang, W. J.; Li, L.; Qin, S. G.; Shi, Y. L.; Liu, G. H.; Li, J. G.

2016-02-01

After commissioning in 2005, the EAST superconducting tokamak had been operated with its water cooled divertors for eight campaigns up to 2012, employing graphite as plasma facing material. With increase in heating power over 20 MW in recent years, the heat flux going to the divertors rises rapidly over 10 MW m-2 for steady state operation. To accommodate the rapid increasing heat load in EAST, the bolting graphite tile divertor must be upgraded. An ITER-like tungsten (W) divertor has been designed and developed; and firstly used for the upper divertor of EAST. The EAST upper W divertor is modular structure with 80 modules in total. Eighty sets of W/Cu plasma-facing components (PFC) with each set consisting of an outer vertical target (OVT), an inner vertical target (IVT) and a DOME, are attached to 80 stainless steel cassette bodies (CB) by pins. The monoblock W/Cu-PFCs have been developed for the strike points of both OVT and IVT, and the flat type W/Cu-PFCs for the DOME and the baffle parts of both OVT and IVT, employing so-called hot isostatic pressing (HIP) technology for tungsten to CuCrZr heat sink bonding, and electron beam welding for CuCrZr to CuCrZr and CuCrZr to other material bonding. Both monoblock and flat type PFC mockups passed high heat flux (HHF) testing by means of electron beam facilities. The 80 divertor modules were installed in EAST in 2014 and results of the first commissioning are presented in this paper.

A protection system for the JET ITER-like wall based on imaging diagnostics.

PubMed

Arnoux, G; Devaux, S; Alves, D; Balboa, I; Balorin, C; Balshaw, N; Beldishevski, M; Carvalho, P; Clever, M; Cramp, S; de Pablos, J-L; de la Cal, E; Falie, D; Garcia-Sanchez, P; Felton, R; Gervaise, V; Goodyear, A; Horton, A; Jachmich, S; Huber, A; Jouve, M; Kinna, D; Kruezi, U; Manzanares, A; Martin, V; McCullen, P; Moncada, V; Obrejan, K; Patel, K; Lomas, P J; Neto, A; Rimini, F; Ruset, C; Schweer, B; Sergienko, G; Sieglin, B; Soleto, A; Stamp, M; Stephen, A; Thomas, P D; Valcárcel, D F; Williams, J; Wilson, J; Zastrow, K-D

2012-10-01

The new JET ITER-like wall (made of beryllium and tungsten) is more fragile than the former carbon fiber composite wall and requires active protection to prevent excessive heat loads on the plasma facing components (PFC). Analog CCD cameras operating in the near infrared wavelength are used to measure surface temperature of the PFCs. Region of interest (ROI) analysis is performed in real time and the maximum temperature measured in each ROI is sent to the vessel thermal map. The protection of the ITER-like wall system started in October 2011 and has already successfully led to a safe landing of the plasma when hot spots were observed on the Be main chamber PFCs. Divertor protection is more of a challenge due to dust deposits that often generate false hot spots. In this contribution we describe the camera, data capture and real time processing systems. We discuss the calibration strategy for the temperature measurements with cross validation with thermal IR cameras and bi-color pyrometers. Most importantly, we demonstrate that a protection system based on CCD cameras can work and show examples of hot spot detections that stop the plasma pulse. The limits of such a design and the associated constraints on the operations are also presented.

Examining the temperature behavior of stainless steel surfaces exposed to hydrogen plasmas in the Lithium Tokamak eXperiment (LTX)

NASA Astrophysics Data System (ADS)

Bedoya, Felipe; Allain, Jean Paul; Kaita, Robert; Lucia, Matthew; St-Onge, Denis; Ellis, Robert; Majeski, Richard

2014-10-01

The Materials Analysis Particle Probe (MAPP) is an in-situ diagnostic designed to characterize plasma-facing components (PFCs) in tokamak devices. MAPP is installed in LTX at Princeton Plasma Physics Laboratory. MAPP's capabilities include remotely operated XPS acquisition and temperature control of four samples. The recent addition of a focused ion beam allows XPS depth profiling analysis. Recent published results show an apparent correlation between hydrogen retention and temperature of Li coated stainless steel (SS) PFCs exposed to plasmas like those of LTX. According to XPS data, the retention of hydrogen by the coated surfaces decreases at above 180 °C. In the present study MAPP will be used to study the oxidation of Li coatings as a function of time and temperature of the walls when Li coatings are applied. Experiments in the ion-surface interaction experiment (IIAX) varying the hydrogen fluence on the SS samples will be also performed. Conclusions resulting from this study will be key to explain the PFC temperature-dependent variation of plasma performance observed in LTX. This work was supported by U.S. DOE Contracts DE-AC02-09CH11466, DE-AC52-07NA27344 and DE-SC0010717.

A protection system for the JET ITER-like wall based on imaging diagnosticsa)

NASA Astrophysics Data System (ADS)

Arnoux, G.; Devaux, S.; Alves, D.; Balboa, I.; Balorin, C.; Balshaw, N.; Beldishevski, M.; Carvalho, P.; Clever, M.; Cramp, S.; de Pablos, J.-L.; de la Cal, E.; Falie, D.; Garcia-Sanchez, P.; Felton, R.; Gervaise, V.; Goodyear, A.; Horton, A.; Jachmich, S.; Huber, A.; Jouve, M.; Kinna, D.; Kruezi, U.; Manzanares, A.; Martin, V.; McCullen, P.; Moncada, V.; Obrejan, K.; Patel, K.; Lomas, P. J.; Neto, A.; Rimini, F.; Ruset, C.; Schweer, B.; Sergienko, G.; Sieglin, B.; Soleto, A.; Stamp, M.; Stephen, A.; Thomas, P. D.; Valcárcel, D. F.; Williams, J.; Wilson, J.; Zastrow, K.-D.; JET-EFDA Contributors

2012-10-01

The new JET ITER-like wall (made of beryllium and tungsten) is more fragile than the former carbon fiber composite wall and requires active protection to prevent excessive heat loads on the plasma facing components (PFC). Analog CCD cameras operating in the near infrared wavelength are used to measure surface temperature of the PFCs. Region of interest (ROI) analysis is performed in real time and the maximum temperature measured in each ROI is sent to the vessel thermal map. The protection of the ITER-like wall system started in October 2011 and has already successfully led to a safe landing of the plasma when hot spots were observed on the Be main chamber PFCs. Divertor protection is more of a challenge due to dust deposits that often generate false hot spots. In this contribution we describe the camera, data capture and real time processing systems. We discuss the calibration strategy for the temperature measurements with cross validation with thermal IR cameras and bi-color pyrometers. Most importantly, we demonstrate that a protection system based on CCD cameras can work and show examples of hot spot detections that stop the plasma pulse. The limits of such a design and the associated constraints on the operations are also presented.

Can tokamaks PFC survive a single event of any plasma instabilities?

NASA Astrophysics Data System (ADS)

Hassanein, A.; Sizyuk, V.; Miloshevsky, G.; Sizyuk, T.

2013-07-01

Plasma instability events such as disruptions, edge-localized modes (ELMs), runaway electrons (REs), and vertical displacement events (VDEs) are continued to be serious events and most limiting factors for successful tokamak reactor concept. The plasma-facing components (PFCs), e.g., wall, divertor, and limited surfaces of a tokamak as well as coolant structure materials are subjected to intense particle and heat loads and must maintain a clean and stable surface environment among them and the core/edge plasma. Typical ITER transient events parameters are used for assessing the damage from these four different instability events. HEIGHTS simulation showed that a single event of a disruption, giant ELM, VDE, or RE can cause significant surface erosion (melting and vaporization) damage to PFC, nearby components, and/or structural materials (VDE, RE) melting and possible burnout of coolant tubes that could result in shut down of reactor for extended repair time.

Thermal modeling of W rod armor.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nygren, Richard Einar

2004-09-01

Sandia has developed and tested mockups armored with W rods over the last decade and pioneered the initial development of W rod armor for International Thermonuclear Experimental Reactor (ITER) in the 1990's. We have also developed 2D and 3D thermal and stress models of W rod-armored plasma facing components (PFCs) and test mockups and are applying the models to both short pulses, i.e. edge localized modes (ELMs), and thermal performance in steady state for applications in C-MOD, DiMES testing and ITER. This paper briefly describes the 2D and 3D models and their applications with emphasis on modeling for an ongoingmore » test program that simulates repeated heat loads from ITER ELMs.« less

Pump and Flow Control Subassembly of Thermal Control Subsystem for Photovoltaic Power Module

NASA Technical Reports Server (NTRS)

Motil, Brian; Santen, Mark A.

1993-01-01

The pump and flow control subassembly (PFCS) is an orbital replacement unit (ORU) on the Space Station Freedom photovoltaic power module (PVM). The PFCS pumps liquid ammonia at a constant rate of approximately 1170 kg/hr while providing temperature control by flow regulation between the radiator and the bypass loop. Also, housed within the ORU is an accumulator to compensate for fluid volumetric changes as well as the electronics and firmware for monitoring and control of the photovoltaic thermal control system (PVTCS). Major electronic functions include signal conditioning, data interfacing and motor control. This paper will provide a description of each major component within the PFCS along with performance test data. In addition, this paper will discuss the flow control algorithm and describe how the nickel hydrogen batteries and associated power electronics will be thermally controlled through regulation of coolant flow to the radiator.

Relative importance of wastewater treatment plants and non-point sources of perfluorinated compounds to Washington State rivers.

PubMed

Furl, Chad V; Meredith, Callie A; Strynar, Mark J; Nakayama, Shoji F

2011-07-01

Perfluorinated compounds (PFCs) were measured in 10 Washington State rivers and 4 wastewater treatment plants (WWTPs) under periods of low and high flows to investigate the relative importance of point and non-point sources to rivers. PFCs were detected in all samples with summed values ranging from 1.11 to 74.9 ng/L in surface waters and 62.3-418 ng/L in WWTP effluent. Concentrations in 6 of the 10 rivers exhibited a positive relationship with flow, indicating runoff as a contributing source, with PFC loads greatest at all 10 waterbodies during high flows. Perfluoroheptanoic acid:perfluorooctanoic acid homologue ratios suggest atmospheric contributions to the waterbodies are important throughout the year. Principal component analysis (PCA) indicated distinct homologue profiles for high flow, low flow, and effluent samples. The PCA demonstrates that during the spring when flows and loads are at their greatest; WWTP discharges are not the primary sources of PFCs to the river systems. Taken together, the evidence provided signifies non-point inputs are a major pathway for PFCs to surface waters in Washington State. Copyright © 2011 Elsevier B.V. All rights reserved.

Adsorption of four perfluorinated acids on non ion exchange polymer sorbents.

PubMed

Senevirathna, S T M L D; Tanaka, S; Fujii, S; Kunacheva, C; Harada, H; Shivakoti, B R; Dinh, H; Ariyadasa, T

2011-01-01

Perfluorinated compounds (PFCs) have attracted global concern due to their ubiquitous distribution and properties of persistence, bio accumulation and toxicity. The process of adsorption has been identified as an effective technique to remove PFCs in water. Different non ion-exchange polymeric adsorbents were tested with regard to their sorption kinetics and isotherms at low PFCs concentrations. Selected PFCs were perfluorobutanoic acid (PFBA), perfluoroheptanoic acid (PFHpA), perfluorooctanoic acid (PFOA) and perfluorodecanoic acid (PFDA) and the tested polymers were three types of Dowex optopores (V-493, V503, and L493), Amberlite XAD-4, and Filtrasorb 400 (Granular Activated Carbon-GAC). We observed the selective adsorption of PFCs on synthetic polymers. For PFDA, Amberlite XAD-4 gave the Freundlich adsorption constant of 2,965 (microg PFCs/g sorbent)(microg PFCs/L)(-n), which was higher than that of GAC (121.89 (microg PFCs/g sorbent) (microg PFCS/L)(-n)). In the case of PFBA, GAC showed better performance (13.36) (microg PFCs/g sorbent) microg PFCS/L)(-n) than synthetic polymers (0.62-5.23) (microg PFCs/g sorbent) (microg PFCS/L)(-n). Adsorption kinetics of all adsorbents were well described (R2 = 0.85-1) by pseudo-second order kinetic model. Sorption capacity was influenced by initial PFCs concentration for all adsorbents. GAC reached the equilibrium concentration within 4 hours, Amberlite XAD 4 reached it within 10 hours and other polymers took more than 70 hours.

Investigation of Plasma Surface Interactions with the PISCES ELM Laser System

NASA Astrophysics Data System (ADS)

Umstadter, K. R.; Baldwin, M.; Hanna, J.; Doerner, R.; Lynch, T.; Palmer, T.; Tynan, G. R.

2007-11-01

When an ELM occurs in tokamaks, up to 30% of the pedestal energy can be deposited on the wall of the tokamak causing heating & material loss due to sublimation, evaporation and melt splashing of plasma facing components (PFCs) and expansion of the ejected material into the plasma. We have explored heat pulses using an electrical power circuit to draw electrons from the plasma to heat samples ohmically. This system is limited in power to ˜250kJ/m^2 at the minimum pulse width of 10ms and depletes the plasma column, complicating spectroscopy. We have completed calculations that indicate that a pulsed laser system can be used to simulate the heat pulse of ELMs. We are integrating laser systems into the existing PFC research program in PISCES, a laboratory facility capable of reproducing plasma-materials interactions expected during normal operation of large tokamaks. Two Nd:YAG lasers capable of delivering up to 50J of energy over various pulsewidths are used for the experiments. Laser heat pulse only, H+/D+ plasma only, and laser+plasma experiments were conducted and initial results indicate that metals behave very differently while exposed to plasma and simultaneous heat pulses. We will also discuss initial results for carbon PFCs and material transport into the plasma. Supported by US DoE grant DE-FG02-07ER-54912.

Interactions of Deuterium Plasma with Lithiated and Boronized Surfaces in NSTX-U

NASA Astrophysics Data System (ADS)

Krstic, Predrag

2015-09-01

The main research goal of the presented research has been to understand the changes in surface composition and chemistry at the nanoscopic temporal and spatial scales for long pulse Plasma Facing Components (PFCs) and link these to the overall machine performance of the National Spherical Torus Experiment Upgrade (NSTX-U). A study is presented of the lithium surface science, with atomic spatial and temporal resolutions. The dynamic surface responds and evolves in a mixed material environments (D, Li, C, B, O, Mo, W) with impingement of plasma particles in the energy range below 100 eV. The results, obtained by quantum-classical molecular dynamics, include microstructure changes, erosion, surface chemistry, deuterium implantation and permeation. Main objectives of the research are i) a comparison of Li and B deposition on carbon, ii) the role of oxygen and other impurities e.g. boron, carbon in the lithium performance, and iii) how this performance will change when lithium is applied to a high-Z refractory metal substrate (Mo, W). In addition to predicting and understanding the phenomenology of the processes, we will show plasma induced erosion of PFCs, including chemical and physical sputtering yields at various temperatures (300-700 K) as well as deuterium uptake/recycling. This work is supported by the U.S. Department of Energy Office of Science, Office of Fusion Energy Science, Award Number DE-SC0013752.

Mass flows of perfluorinated compounds (PFCs) in central wastewater treatment plants of industrial zones in Thailand.

PubMed

Kunacheva, Chinagarn; Tanaka, Shuhei; Fujii, Shigeo; Boontanon, Suwanna Kitpati; Musirat, Chanatip; Wongwattana, Thana; Shivakoti, Binaya Raj

2011-04-01

Perfluorinated compounds (PFCs) are fully fluorinated organic compounds, which have been used in many industrial processes and have been detected in wastewater and sludge from municipal wastewater treatment plants (WWTPs) around the world. This study focused on the occurrences of PFCs and PFCs mass flows in the industrial wastewater treatment plants, which reported to be the important sources of PFCs. Surveys were conducted in central wastewater treatment plant in two industrial zones in Thailand. Samples were collected from influent, aeration tank, secondary clarifier effluent, effluent and sludge. The major purpose of this field study was to identify PFCs occurrences and mass flow during industrial WWTP. Solid-phase extraction (SPE) coupled with HPLC-ESI-MS/MS were used for the analysis. Total 10 PFCs including perfluorooctane sulfonate (PFOS), perfluorooctanoic acid (PFOA), perfluoropropanoic acid (PFPA), perfluorohexanoic acid (PFHxA), perfluoroheptanoic acid (PFHpA), perfluorohexane sulfonate (PFHxS), perfluoronanoic acid (PFNA), perfluordecanoic acid (PFDA), perfluoroundecanoic acid (PFUnA), and perfluorododecanoic acid (PFDoA) were measured to identify their occurrences. PFCs were detected in both liquid and solid phase in most samples. The exceptionally high level of PFCs was detected in the treatment plant of IZ1 and IZ2 ranging between 662-847ngL(-1) and 674-1383ngL(-1), respectively, which greater than PFCs found in most domestic wastewater. Due to PFCs non-biodegradable property, both WWTPs were found ineffective in removing PFCs using activated sludge processes. Bio-accumulation in sludge could be the major removal mechanism of PFCs in the process. The increasing amount of PFCs after activated sludge processes were identified which could be due to the degradation of PFCs precursors. PFCs concentration found in the effluent were very high comparing to those in river water of the area. Industrial activity could be the one of major sources of PFCs contamination in the water environment. Copyright © 2011 Elsevier Ltd. All rights reserved.

Synergistic effects of surface erosion on tritium inventory and permeation in metallic plasma facing armours

NASA Astrophysics Data System (ADS)

Federici, G.; Holland, D. F.; Matera, R.

1996-10-01

In the next generation of DT fuelled tokamaks, i.e., the International Thermonuclear Experimental Reactor (ITER) implantation of energetic DT particles on some portions of the plasma facing components (PFCs) will take place along with significant erosion of the armour surfaces. As a result of the simultaneous removal of material from the front surface, the build-up of tritium inventory and the start of permeation originating in the presence of large densities of neutron-induced traps is expected to be influenced considerably and special provisions could be required to minimise the consequences on the design. This paper reports on the results of a tritium transport modelling study based on a new model which describes the migration of implanted tritium across the bulk of metallic plasma facing materials containing neutron-induced traps which can capture it and includes the synergistic effects of surface erosion. The physical basis of the model is summarised, but emphasis is on the discussion of the results of a comparative study performed for beryllium and tungsten armours for ranges of design and operation conditions similar to those anticipated in the divertor of ITER.

Perfluorinated compounds (PFCs) in the atmosphere of Shenzhen, China: Spatial distribution, sources and health risk assessment.

PubMed

Liu, Baolin; Zhang, Hong; Yao, Dan; Li, Juying; Xie, Liuwei; Wang, Xinxuan; Wang, Yanping; Liu, Guoqing; Yang, Bo

2015-11-01

This study investigated the occurrence of perfluorinated compounds (PFCs) in the atmosphere of Shenzhen, China. 11 PFCs, including two perfluoroalkyl sulfonic acids (PFSAs, C6 and C8) and perfluoroalkyl carboxylic acids (PFCAs, C4-12) were determined by high performance liquid chromatography-negative electrospray ionization-tandem mass spectrometry (HPLC/ESI-MS/MS). Total PFC concentrations (∑ PFCs) in the atmospheric samples ranged from 3.4 to 34 pg m(-3) with an average of 15 pg m(-3). Perfluorooctanoic acid (PFOA) and perfluorooctane sulfonic acid (PFOS) were the two most abundant PFCs and on average accounted for 35% and 22% of ∑ PFCs, respectively. ∑ PFCs and total PFCA concentrations (∑ PFCAs) showed a tendency of low-lying East West, while the distribution of total PFSA concentrations (∑ PFSAs) was uniform. Higher concentrations of ∑ PFCs were found in Bao'an District which had very well-developed manufacturing industries. PCA model was employed to quantitatively calculate the contributions of sources. The results showed that PFOA-factor, long chain PFCs-factor and PFOS-factor were the three main source categories for PFCs in the atmosphere. Meanwhile, long-distance transport of pollutants from southeastern coastal areas might be another source of PFCs in Shenzhen atmosphere. PFCs in the atmosphere were more positively correlated with the levels PM10 than PM2.5, which indicated PFCs were more likely to adhere to particles with relatively large sizes. The hazard ratios of noncancer risk through breathing based on PFOS and PFOA concentrations were calculated and were less than unity, suggesting that PFCs concentrations may pose no or immediate threat to the residents in Shenzhen. Copyright © 2015 Elsevier Ltd. All rights reserved.

PERSISTENT PERFLUORINATED ORGANIC COMPOUNDS

EPA Science Inventory

Perfluorinated compounds (PFCs) have gained notoriety in the recent past. Global distribution of PFCs in wildlife, environmental samples and humans has sparked a recent increase in new investigations concerning PFCs. Historically PFCs have been used in a wide variety of consume...

Designs of LiMIT as a Limiter in the EAST Tokamak

NASA Astrophysics Data System (ADS)

Szott, Matthew; Christenson, Michael; Kalathiparambil, Kishor; Ruzic, David

2016-10-01

Liquid metal plasma facing components (PFCs) provide a constantly refreshing, self-healing surface that can reduce erosion and thermal stress damage to prolong device lifetime, and additionally decrease edge recycling, reduce impurities, and enhance plasma performance. The Liquid Metal Infused Trench (LiMIT) system, developed at UIUC, has demonstrated thermoelectric magnetohydrodynamic (TEMHD) driven flow of liquid lithium through series of solid trenches. This TEMHD effect drives liquid lithium in fusion systems using the plasma heat flux and the toroidal magnetic field, and the surface tension of the liquid lithium maintains a fresh surface on top of the solid trenches. LiMIT has been successfully tested at UIUC as well as HT-7 and Magnum PSI at heat fluxes up to 3 MW/m2. The next step is demonstrating system viability in full-scale fusion-relevant conditions. In collaboration with a team in Hefei, design and testing has begun for a large scale LiMIT system that will act as a limiter in EAST. The designs improve upon previous versions of LiMIT tested at Illinois and incorporate lessons learned from earlier tests of liquid metal PFCs at EAST. Existing infrastructure is used to load and supply lithium to the system, and the LiMIT trenches will help maintain a smooth, fresh surface as well as aid in propelling the lithium out of direct plasma flux to improve heat transfer. Supported by DOE/ALPS DE-FG02-99ER54515.

ELM mitigation with pellet ELM triggering and implications for PFCs and plasma performance in ITER

DOE PAGES

Baylor, Larry R.; Lang, P. T.; Allen, Steve L.; ...

2014-10-05

The triggering of rapid small edge localized modes (ELMs) by high frequency pellet injection has been proposed as a method to prevent large naturally occurring ELMs that can erode the ITER plasma facing components. Deuterium pellet injection has been used to successfully demonstrate the on-demand triggering of edge localized modes (ELMs) at much higher rates and with much smaller intensity than natural ELMs. The proposed hypothesis for the triggering mechanism of ELMs by pellets is the local pressure perturbation resulting from reheating of the pellet cloud that can exceed the local high-n ballooning mode threshold where the pellet is injected.more » Nonlinear MHD simulations of the pellet ELM triggering show destabilization of high-n ballooning modes by such a local pressure perturbation. A review of the recent pellet ELM triggering results from ASDEX Upgrade (AUG), DIII-D, and JET reveals that a number of uncertainties about this ELM mitigation technique still remain. These include the heat flux impact pattern on the divertor and wall from pellet triggered and natural ELMs, the necessary pellet size and injection location to reliably trigger ELMs, and the level of fueling to be expected from ELM triggering pellets and synergy with larger fueling pellets. The implications of these issues for pellet ELM mitigation in ITER and its impact on the PFCs are presented along with the design features of the pellet injection system for ITER.« less

Vessel thermal map real-time system for the JET tokamak

NASA Astrophysics Data System (ADS)

Alves, D.; Felton, R.; Jachmich, S.; Lomas, P.; McCullen, P.; Neto, A.; Valcárcel, D. F.; Arnoux, G.; Card, P.; Devaux, S.; Goodyear, A.; Kinna, D.; Stephen, A.; Zastrow, K.-D.

2012-05-01

The installation of international thermonuclear experimental reactor-relevant materials for the plasma facing components (PFCs) in the Joint European Torus (JET) is expected to have a strong impact on the operation and protection of the experiment. In particular, the use of all-beryllium tiles, which deteriorate at a substantially lower temperature than the formerly installed carbon fiber composite tiles, imposes strict thermal restrictions on the PFCs during operation. Prompt and precise responses are therefore required whenever anomalous temperatures are detected. The new vessel thermal map real-time application collects the temperature measurements provided by dedicated pyrometers and infrared cameras, groups them according to spatial location and probable offending heat source, and raises alarms that will trigger appropriate protective responses. In the context of the JET global scheme for the protection of the new wall, the system is required to run on a 10 ms cycle communicating with other systems through the real-time data network. In order to meet these requirements a commercial off-the-shelf solution has been adopted based on standard x86 multicore technology. Linux and the multithreaded application real-time executor (MARTe) software framework were respectively the operating system of choice and the real-time framework used to build the application. This paper presents an overview of the system with particular technical focus on the configuration of its real-time capability and the benefits of the modular development approach and advanced tools provided by the MARTe framework.

Perfluorinated Compounds in Fish from US Urban Rivers and ...

EPA Pesticide Factsheets

Perfluorinated compounds (PFCs) have recently received scientific and regulatory attention due to their broad environmental distribution, persistence, bioaccumulative potential, and toxicity. Some studies suggest that the consumption of fish from contaminated waters may be a major source of human exposure to perfluorooctane sulfonate (PFOS) or other long-chain perfluorocarboxylic acids. Much of the existing PFC fish tissue literature focuses on marine fish species and on fish collected outside of the continental U.S. To broaden the assessment of PFCs in U.S. fish, a comprehensive characterization of PFC contamination in freshwater fish was initiated on a national scale during the U.S. EPA 2008-2009 National Rivers and Streams Assessment and during the Great Lakes Human Health Fish Tissue Study component of the 2010 EPA National Coastal Condition Assessment (NCCA/GL). National estimates were developed for PFCs in fish from urban rivers and regional estimates for fish in the U.S. Great Lakes using an unequal probability design. Fish were collected from a statistically representative set of 164 urban river sites and from 157 randomly selected nearshore sites in the U.S. throughout the five Great Lakes. The probability design allowed extrapolation to the sampled population of 17,059 km in urban rivers and a nearshore area of 11,091 km2 in the Great Lakes. Fish fillet tissue was analyzed for 13 PFCs using high-performance liquid chromatography tandem mass spec

[Influence of tap water treatment on perfluorinated compounds residue in the dissolved phase].

PubMed

Zhang, Hong; Chen, Qing-wu; Wang, Xin-xuan; Chai, Zhi-fang; Shen, Jin-can; Yang, Bo; Liu, Guo-qing

2013-09-01

To study the perfluorinated compounds (PFCs) residues through water treatments including flocculation, sedimentation, sand filtration, ozonation with activated carbon and chlorination, as well as the seasonal variation of PFCs in the raw water of waterworks, 13 PFCs species in the dissolved phase of raw water, finished water, as well as the water samples after flocculation, sedimentation, sand filtration, and ozonation with activated carbon filtration were measured by the high performance liquid chromatography-tandem mass spectrometry combined with solid phase extraction. Results indicated that sigma PFCs residue in water was higher in spring and summer than that in fall and winter. The vast majority of PFCs in samples were of short and medium chains (C < or = 10), and perfluorooctane sulfonate was the most typical residue species. Among the five water treatment stages, sedimentation, sand filtration and ozonation with activated carbon filtration can remove PFCs, while flocculation and chlorination significantly raise the levels of short- (C < or = 6) and medium-chain (10 > or = C > or = 7) PFCs, respectively, causing sigma PFCs increase in finished water by 10%-44% compared to raw water. However, the PFCs residues in finished water are still far below their limit values, posing no threat against human health.

PERFLUORINATED COMPOUNDS (PFCs) IN SERUM OF CATS – LINKAGE TO INDOOR EXPOSURES.

EPA Science Inventory

The PFCs have been used in a wide range of consumer, including residential, products (e.g., stain-resistant coatings for carpets and upholstery). Carbon-fluoride bonds are highly stable, mak-ing PFCs extremely resistant to biodegradation. Thus, PFCs have become globally distribut...

Arcing and its role in PFC erosion and dust production in DIII-D

NASA Astrophysics Data System (ADS)

Rudakov, D. L.; Chrobak, C. P.; Doerner, R. P.; Krasheninnikov, S. I.; Moyer, R. A.; Umstadter, K. R.; Wampler, W. R.; Wong, C. P. C.

2013-07-01

Two types of arc tracks are observed on the plasma-facing components (PFCs) in DIII-D. "Unmagnetized" random walk tracks are produced during glow discharges; they are rare and have no importance for PFC erosion but may degrade diagnostic mirrors. "Magnetized" scratch-like type II tracks are produced by unipolar arcs during plasma operations; they are formed by "retrograde BxJ" motion of the cathode spot and are roughly perpendicular to the local magnetic field. Type II arcs cause measurable erosion of graphite, but based on the evidence available they are relatively small contributors to the total erosion of carbon in DIII-D compared to other mechanisms such as physical and chemical sputtering and ablation from leading edges. Erosion by arcing of tungsten films deposited on graphite samples was observed in Divertor Material Evaluation System (DiMES) experiments. New DiMES experiments aimed at time-resolved arc measurements are proposed.

Unraveling wall conditioning effects on plasma facing components in NSTX-U with the Materials Analysis Particle Probe (MAPP)

DOE PAGES

Bedoya, F.; Allain, J. P.; Kaita, R.; ...

2016-07-14

A novel PFC diagnostic, the Materials Analysis Particle Probe (MAPP), has been recently commissioned in the National Spherical Torus Experiment Upgrade (NSTX-U). MAPP is currently monitoring the chemical evolution of the PFCs in the NSTX-U lower divertor at 107 cm from the tokamak axis on a day-to-day basis. Here in this work, we summarize the methodology that was adopted to obtain qualitative and quantitative descriptions of the samples chemistry. Using this methodology, we were able to describe all the features in all our spectra to within a standard deviation of ±0.22 eV in position and ±248 s -1 eV inmore » area. Additionally, we provide an example of this methodology with data of boronized ATJ graphite exposed to NSTX-U plasmas.« less

Meso-pores carbon nano-tubes (CNTs) tissues-perfluorocarbons (PFCs) hybrid air-electrodes for Li-O2 battery

NASA Astrophysics Data System (ADS)

Balaish, Moran; Ein-Eli, Yair

2018-03-01

Adding immiscible perfluorocarbons (PFCs), possessing superior oxygen solubility and diffusivity, to a free-standing (metal-free and binder-free) CNTs air-electrode tissues with a meso-pore structure, fully maximized the advantages of PFCs as oxygenated-species' channels-providers. The discharge behavior of hybrid PFCs-CNT Li-O2 systems demonstrated a drastic increase in cell capacity at high current density (0.2 mA cm-2), where oxygen transport limitations are best illustrated. The results of this research revealed several key factors affecting PFCs-Li-O2 systems. The incorporation of PFCs with higher superoxide solubility and oxygen diffusivity, but more importantly higher PFCs/electrolyte miscibility, in a meso-pore air-electrode enabled better exploitation of PFCs potential. Consequently, the utilization of the air-electrode' surface area was enhanced via the formation of artificial three phase reaction zones with additional oxygen transportation routes, leading to uniform and intimate Li2O2 deposit at areas further away from the oxygen reservoir. Associated mechanisms are discussed along with insights into an improved Li-O2 battery system.

Landfills as sources of polyfluorinated compounds, polybrominated diphenyl ethers and musk fragrances to ambient air

NASA Astrophysics Data System (ADS)

Weinberg, Ingo; Dreyer, Annekatrin; Ebinghaus, Ralf

2011-02-01

In order to investigate landfills as sources of polyfluorinated compounds (PFCs), polybrominated diphenyl ethers (PBDEs) and synthetic musk fragrances to the atmosphere, air samples were simultaneously taken at two landfills (one active and one closed) and two reference sites using high volume air samplers. Contaminants were accumulated on glass fiber filters (particle phase) and PUF/XAD-2/PUF cartridges (gas phase), extracted by methyl-tert butyl ether/acetone (neutral PFCs), methanol (ionic PFCs) or hexane/acetone (PBDEs, musk fragrances), and detected by GC-MS (neutral PFCs, PBDEs, musk fragrances) or HPLC-MS/MS (ionic PFCs). Total concentrations ranged from 84 to 706 pg m -3 (volatile PFCs, gas phase), from

Measurements of impurity concentrations and transport in the Lithium Tokamak Experiment

NASA Astrophysics Data System (ADS)

Boyle, Dennis Patrick

This thesis presents new measurements of core impurity concentrations and transport in plasmas with lithium coatings on all-metal plasma facing components (PFCs) in the Lithium Tokamak Experiment (LTX). LTX is a modest-sized spherical tokamak uniquely capable of operating with large area solid and/or liquid lithium coatings essentially surrounding the entire plasma (as opposed to just the divertor or limiter region in other devices). Lithium (Li) wall-coatings have improved plasma performance and confinement in several tokamaks with carbon (C) PFCs, including the National Spherical Torus Experiment (NSTX). In NSTX, contamination of the core plasma with Li impurities was very low (<0.1%) despite extensive divertor coatings. Low Li levels in NSTX were found to be largely due to neoclassical forces from the high level of C impurities. Studying impurity levels and transport with Li coatings on stainless steel surfaces in LTX is relevant to future devices (including future enhancements to NSTX-Upgrade) with all-metal PFCs. The new measurements in this thesis were enabled by a refurbished Thomson scattering system and improved impurity spectroscopy, primarily using a novel visible spectrometer monitoring several Li, C, and oxygen (O) emission lines. A simple model was used to account for impurities in unmeasured charge states, assuming constant density in the plasma core and constant concentration in the edge. In discharges with solid Li coatings, volume averaged impurity concentrations were low but non-negligible, with 2-4% Li, 0.6-2% C, 0.4-0.7% O, and Z eff<1.2. Transport was assessed using the TRANSP, NCLASS, and MIST codes. Collisions with the main H ions dominated the neoclassical impurity transport, unlike in NSTX, where collisions with C dominated. Furthermore, neoclassical transport coefficients calculated with NCLASS were similar across all impurity species and differed no more than a factor of two, in contrast to NSTX where they differed by an order of magnitude. However, time-independent simulations with MIST indicated that unlike NSTX, neoclassical theory did not fully capture the impurity transport and anomalous transport likely played a significant role in determining impurity profiles.

Measurements of impurity concentrations and transport in the Lithium Tokamak Experiment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Boyle, Dennis Patrick

This thesis presents new measurements of core impurity concentrations and transport in plasmas with lithium coatings on all-metal plasma facing components (PFCs) in the Lithium Tokamak Experiment (LTX). LTX is a modest-sized spherical tokamak uniquely capable of operating with large area solid and/or liquid lithium coatings essentially surrounding the entire plasma (as opposed to just the divertor or limiter region in other devices). Lithium (Li) wall-coatings have improved plasma performance and confinement in several tokamaks with carbon (C) PFCs, including the National Spherical Torus Experiment (NSTX). In NSTX, contamination of the core plasma with Li impurities was very low (<0.1%)more » despite extensive divertor coatings. Low Li levels in NSTX were found to be largely due to neoclassical forces from the high level of C impurities. Studying impurity levels and transport with Li coatings on stainless steel surfaces in LTX is relevant to future devices (including future enhancements to NSTX-Upgrade) with all-metal PFCs. The new measurements in this thesis were enabled by a refurbished Thomson scattering system and improved impurity spectroscopy, primarily using a novel visible spectrometer monitoring several Li, C, and oxygen (O) emission lines. A simple model was used to account for impurities in unmeasured charge states, assuming constant density in the plasma core and constant concentration in the edge. In discharges with solid Li coatings, volume averaged impurity concentrations were low but non-negligible, with~2-4% Li, ~0.6-2% C, ~0.4-0.7% O, and Z_eff<1.2. Transport was assessed using the TRANSP, NCLASS, and MIST codes. Collisions with the main H ions dominated the neoclassical impurity transport, unlike in NSTX, where collisions with C dominated. Furthermore, neoclassical transport coefficients calculated with NCLASS were similar across all impurity species and differed no more than a factor of two, in contrast to NSTX where they differed by an order of magnitude. However, time-independent simulations with MIST indicated that unlike NSTX, neoclassical theory did not fully capture the impurity transport and anomalous transport likely played a significant role in determining impurity profiles.« less

Behavior of W-SiC/SiC dual layer tiles under LHD plasma exposure

NASA Astrophysics Data System (ADS)

Mohrez, Waleed A.; Kishimoto, Hirotatsu; Kohno, Yutaka; Hirotaki, S.; Kohyama, Akira

2013-11-01

Towards the early realization of fusion power reactors, high performance first wall and plasma facing components (PFCs) are essentially required. As one of the biggest challenges for this, high heat flux component (HHFC) design and R & D has been emphasized. This report provides the high performance HHFC materials R & D status and the first plasma exposure test result from large helical device (LHD). W-SiC/SiC dual layer tiles (hereafter, W-SiC/SiC) were developed by applied NITE process. This is the realistic concept of tungsten armor with ceramic composite substrates for fusion power reactors. The dual layer tiles were fabricated and tested their survival under the LHD divertor plasma exposure (Nominally 10 MW/m2 maximum heat load for 6 s operation cycle). The microstructure evolution, including crack and pore formation, was analyzed, besides the behavior of bonding layer between tungsten and SiC/SiC was evaluated by C-scanning images of ultrasonic method and Electron probe Micro-analyzer (EPMA). Thermal analysis was conducted by finite element method, where ANSYS code release 13.0 was used.

Occurrences and behavior of perfluorinated compounds (PFCs) in several wastewater treatment plants (WWTPs) in Japan and Thailand.

PubMed

Shivakoti, Binaya Raj; Tanaka, Shuhei; Fujii, Shigeo; Kunacheva, Chinagarn; Boontanon, Suwanna Kitpati; Musirat, Chanatip; Seneviratne, S T M L D; Tanaka, Hiroaki

2010-06-01

This study examines occurrences of 11 perfluorinated compounds (PFCs) in several wastewater treatment plants in Japan and Thailand. Surveys are conducted in eight wastewater treatment plants (WWTPs) in Japan and central WWTPs of five industrial estates (IEs) in Thailand. Samples are collected from all major treatment processes in order to understand the behavior of PFCs in WWTPs. PFCs are detected in all WWTPs in Japan and Thailand. Concentrations of PFCs even exceed several thousands ng/L in some WWTPs. PFOS, PFOA, and PFNA are mainly detected in WWTPs in Japan, while PFBuS, PFOA, and PFHxA are mainly detected in WWTP of IEs in Thailand. Even though some of the investigated WWTPs utilize biological treatment processes coupled with chlorination, ozonation, or activated carbon adsorption, they are found ineffective to remove PFCs. During the treatment process, PFCs are found to accumulate at exceptionally high concentration levels in the activated sludge of an aeration tank and returned activated sludge. Overall, the estimated total daily mass of discharged PFCs is 124.95 g/d (PFASs: 49.81 g/d; PFCAs: 75.14 g/d) from eight WWTPs in Japan and 55.04 g/d (PFASs: 12 g/d; PFCAs: 43.04 g/d) from five WWTPs in Thailand. Although the presented data are from a single observation in each WWTP, the results indicate that certain industries using PFCs in manufacturing processes could be the principle point source, while domestic activities could be releasing PFCs at detectable levels causing environmental concern.

Endosonography guided management of pancreatic fluid collections

PubMed Central

Vilmann, Andreas S; Menachery, John; Tang, Shou-Jiang; Srinivasan, Indu; Vilmann, Peter

2015-01-01

The revised Atlanta classification of acute pancreatitis was adopted by international consensus, and is based on actual local and systemic determinants of disease severity. The local determinant is pancreatic necrosis (sterile or infected), and the systemic determinant is organ failure. Local complications of pancreatitis can include acute peri-pancreatic fluid collection, acute necrotic collection, pseudocyst formation, and walled-off necrosis. Interventional endoscopic ultrasound (EUS) has been increasing utilized in managing these local complications. After performing a PubMed search, the authors manually applied pre-defined inclusion criteria or a filter to identify publications relevant to EUS and pancreatic collections (PFCs). The authors then reviewed the utility, efficacy, and risks associated with using therapeutic EUS and involved EUS devices in treating PFCs. Due to the development and regulatory approval of improved and novel endoscopic devices specifically designed for transmural drainage of fluid and necrotic debris (access and patency devices), the authors predict continuing evolution in the management of PFCs. We believe that EUS will become an indispensable part of procedures used to diagnose PFCs and perform image-guided interventions. After draining a PFC, the amount of tissue necrosis is the most important predictor of a successful outcome. Hence, it seems logical to classify these collections based on their percentage of necrotic component or debris present when viewed by imaging methods or EUS. Finally, the authors propose an algorithm for managing fluid collections based on their size, location, associated symptoms, internal echogenic patterns, and content. PMID:26557008

An Integrated Modeling Approach for Describing Fate and Transport of Perfluorinated Compounds (PFCs) in Estuarine Reservoir

NASA Astrophysics Data System (ADS)

Zhang, J.; Nguyen Viet, T.; Wang, X.; Chen, H.; Gin, K. Y. H.

2014-12-01

The fate and transport processes of emerging contaminants in aquatic ecosystems are complex, which are not only determined by their own properties but also influenced by the environmental setting, physical, chemical and biological processes. A 3D-emerging contaminant model has been developed based on Delft3D water quality model and coupled with a hydrodynamic model and a catchment-scale 1D- hydrological and hydraulic model to study the possible fate and transport mechanisms of perfluorinated compounds (PFCs) in Marina Reservoir in Singapore. The main processes in the contaminant model include partitioning (among detritus, dissolved organic matter and phytoplankton), settling, resuspension and degradation. We used the integrated model to quantify the distribution of the total PFCs and two major components, namely perfluorooctanoate (PFOA) and perfluorooctane sulfonate (PFOS) in the water, sediments and organisms in the reservoir. The model yielded good agreement with the field measurements when evaluated based on the datasets in 2009 and 2010 as well as recent observations in 2013 and 2014. Our results elucidate that the model can be a useful tool to characterize the occurrence, sources, sinks and trends of PFCs both in the water column and in the sediments in the reservoir. Thisapproach provides a better understanding of mechanisms that influence the fate and transport of emerging contaminants and lays down a framework for future experiments to further explore how the dominant environmental factors change towards mitigation of emerging contaminants in the reservoirs.

From core to coax: extending core RF modelling to include SOL, Antenna, and PFC

NASA Astrophysics Data System (ADS)

Shiraiwa, Syun'ichi

2017-10-01

A new technique for the calculation of RF waves in toroidal geometry enables the simultaneous incorporation of antenna geometry, plasma facing components (PFCs), the scrape off-layer (SOL), and core propagation. Traditionally, core RF wave propagation and antenna coupling has been calculated separately both using rather simplified SOL plasmas. The new approach, instead, allows capturing wave propagation in the SOL and its interactions with non-conforming PFCs permitting self-consistent calculation of core absorption and edge power loss, as well as investigating far and near field impurity generation from RF sheaths and a breakdown issue from antenna electric fields. Our approach combines the field solutions obtained from a core spectral code with a hot plasma dielectric and an edge FEM code using a cold plasma approximation via surface admittance-like matrix. Our approach was verified using the TORIC core ICRF spectral code and the commercial COMSOL FEM package, and was extended to 3D torus using open-source scalable MFEM library. The simulation result revealed that as the core wave damping gets weaker, the wave absorption in edge could become non-negligible. Three dimensional capabilities with non axisymmetric edge are being applied to study the antenna characteristic difference between the field aligned and toroidally aligned antennas on Alcator C-Mod, as well as the surface wave excitation on NSTX-U. Work supported by the U.S. DoE, OFES, using User Facility Alcator C-Mod, DE-FC02-99ER54512 and Contract No. DE-FC02-01ER54648.

Impact and mitigation of disruptions with the ITER-like wall in JET

NASA Astrophysics Data System (ADS)

Lehnen, M.; Arnoux, G.; Brezinsek, S.; Flanagan, J.; Gerasimov, S. N.; Hartmann, N.; Hender, T. C.; Huber, A.; Jachmich, S.; Kiptily, V.; Kruezi, U.; Matthews, G. F.; Morris, J.; Plyusnin, V. V.; Reux, C.; Riccardo, V.; Sieglin, B.; de Vries, P. C.; EFDA Contributors, JET

2013-09-01

Disruptions are a critical issue for ITER because of the high thermal and magnetic energies that are released on short timescales, which results in extreme forces and heat loads. The choice of material of the plasma-facing components (PFCs) can have significant impact on the loads that arise during a disruption. With the ITER-like wall (ILW) in JET made of beryllium in the main chamber and tungsten in the divertor, the main finding is a low fraction of radiation. This has dropped significantly with the ILW from 50-100% of the total energy being dissipated during disruptions in CFC wall plasmas, to less than 50% on average and down to just 10% for vertical displacement events (VDEs). All other changes in disruption properties and loads are consequences of this low radiation: long current quenches (CQs), high vessel forces caused by halo currents and toroidal current asymmetries as well as severe heat loads. Temperatures close to the melting limit have been locally observed on upper first wall structures during deliberate VDE and even at plasma currents as low as 1.5 MA and thermal energy of about 1.5 MJ only. A high radiation fraction can be regained by massive injection of a mixture of 10% Ar with 90% D2. This accelerates the CQ thus reducing the halo current and sideways impulse. The temperature of PFCs stays below 400 °C. MGI is now a mandatory tool to mitigate disruptions in closed-loop operation for currents at and above 2.5 MA in JET.

Formation and termination of runaway beams in ITER disruptions

NASA Astrophysics Data System (ADS)

Martín-Solís, J. R.; Loarte, A.; Lehnen, M.

2017-06-01

A self-consistent analysis of the relevant physics regarding the formation and termination of runaway beams during mitigated disruptions by Ar and Ne injection is presented for selected ITER scenarios with the aim of improving our understanding of the physics underlying the runaway heat loads onto the plasma facing components (PFCs) and identifying open issues for developing and accessing disruption mitigation schemes for ITER. This is carried out by means of simplified models, but still retaining sufficient details of the key physical processes, including: (a) the expected dominant runaway generation mechanisms (avalanche and primary runaway seeds: Dreicer and hot tail runaway generation, tritium decay and Compton scattering of γ rays emitted by the activated wall), (b) effects associated with the plasma and runaway current density profile shape, and (c) corrections to the runaway dynamics to account for the collisions of the runaways with the partially stripped impurity ions, which are found to have strong effects leading to low runaway current generation and low energy conversion during current termination for mitigated disruptions by noble gas injection (particularly for Ne injection) for the shortest current quench times compatible with acceptable forces on the ITER vessel and in-vessel components ({τ\\text{res}}∼ 22~\\text{ms} ). For the case of long current quench times ({τ\\text{res}}∼ 66~\\text{ms} ), runaway beams up to  ∼10 MA can be generated during the disruption current quench and, if the termination of the runaway current is slow enough, the generation of runaways by the avalanche mechanism can play an important role, increasing substantially the energy deposited by the runaways onto the PFCs up to a few hundreds of MJs. Mixed impurity (Ar or Ne) plus deuterium injection proves to be effective in controlling the formation of the runaway current during the current quench, even for the longest current quench times, as well as in decreasing the energy deposited on the runaway electrons during current termination.

Perfluorinated substance assessment in sediments of a large-scale reservoir in Danjiangkou, China.

PubMed

He, Xiaomin; Li, Aimin; Wang, Shengyao; Chen, Hao; Yang, Zixin

2018-01-07

The occurrence of eight perfluorinated compounds (PFCs) in the surface sediments from 10 sampling sites spread across the Danjiangkou Reservoir was investigated by isotope dilution ultra-high-performance liquid chromatography-tandem mass spectrometry (UPLC-MS/MS) after solid-phase extraction (SPE). All the sediments from the 10 sites contained detectable levels of PFCs. The total concentration of the target PFCs in each sediment sample (C ∑PFCs ) ranged from 0.270 to 0.395 ng g -1 of dry weight, and the mean value of C ∑PFCs was 0.324 ± 0.045 ng g -1 of dry weight for the whole reservoir. For each perfluorinated compound in one sediment, perfluorooctane sulfonate (PFOS) or perfluoro-n-butanoic acid (PFBA) consistently had a higher concentration than the other six PFCs, while perfluoro-n-octanoic acid (PFOA) was always undetectable. In terms of spatial distribution, the total and individual concentrations of PFCs in sediment from downstream sites of the Danjiangkou Reservoir were higher than those from upstream sites. Factor analysis revealed that PFCs in the sediment samples originated from electroplating and anti-fog agents in industry, food/pharmaceutical packaging and the water/oil repellent paper coating, and the deposition process. The quotient method was utilized to assess the ecological risk of PFCs in the sediments of the Danjiangkou Reservoir, which showed that the concentrations of PFCs were not considered a risk. In this study, detailed information on the concentration level and distribution of PFCs in the sediments of the Danjiangkou Reservoir, which is the source of water for the Middle Route Project of the South-to-North Water Transfer Scheme in China, was reported and analyzed for the first time. These results can provide valuable information for water resource management and pollution control in the Danjiangkou Reservoir.

Pollution patterns and characteristics of perfluorinated compounds in surface water adjacent potential industrial emission categories of Shanghai, China.

PubMed

Chai, Jian-Fei; Lei, Peng-Hui; Xia, Xiao-Yu; Xu, Gang; Wang, De-Jin; Sun, Rui; Gu, Jian-Zhong; Tang, Liang

2017-11-01

Perfluorinated compounds (PFCs) have received increasing attention worldwide recently because of potential risk to aquatic environment and living organisms. Herein, occurrence and spatial distributions of 17 selected PFCs were investigated in surface water adjacent to potential industrial emission categories in Shanghai. The results showed the distributions of PFCs in the ambient rivers were greatly affected by those industrial sources. Perfluorooctanoic acid (PFOA) and other short-chain PFCs such as perfluoropentanoic acid (PFPeA) and perfluorooctanesulfonate (PFBS) were detected as the predominant species in all samples. Specifically, the total concentrations of PFCs (∑PFCs) near the airport ranged from 142 to 264ngL -1 , with PFOA, PFPeA, and PFBS as most prevalent. While near the fluorochemical plant and metal plating, concentrations of ∑PFCs ranged from 200 to 2143ngL -1 and 211ngL -1 to 705ngL -1 ; and PFOA was the predominant individual PFCs, with the highest concentration of 1985ngL -1 . However, concentrations of PFOS were found at relatively low level, which ranged from < 0.06 to 4.44ngL -1 . The Spearman correlation analysis of concentration of individual PFCs showed that PFOA and perfluorohexanoic acid (PFHxA) was positive, while the correlation between PFOA and perfluorohexansulfonate (PFHxS) was negative near the airport, indicating PFOA and PFHxA may share common sources. Preliminary ecological risk evaluation of PFCs in adjacent water of the industrial emission areas suggested these emission categories posed higher risks than other area, although the risk level was still relatively safe. Copyright © 2017 Elsevier Inc. All rights reserved.

Occurrence investigation of perfluorinated compounds in surface water from East Lake (Wuhan, China) upon rapid and selective magnetic solid-phase extraction

PubMed Central

Zhou, Yusun; Tao, Yun; Li, Huarong; Zhou, Tingting; Jing, Tao; Zhou, Yikai; Mei, Surong

2016-01-01

Using a novel magnetic nanocomposite as adsorbent, a convenient and effective magnetic solid-phase extraction (MSPE) procedure was established for selective separation and concentration of nine perfluorinated compounds (PFCs) in surface water sample. Then an ultra high-performance liquid chromatography-tandem mass spectrometry (UPLC-MS/MS) system was employed for detection of PFCs. Good linearity of the developed analytical method was in the range of 0.5–100 ng L−1 with R2 > 0.9917, and the limits of detection (LODs) ranged from 0.029 to 0.099 ng L−1. At three fortified concentrations of 0.5, 5 and 50 ng L−1, the spiked recoveries of PFCs were in the range of 90.05–106.67% with RSDs < 12.62% (n = 3). The proposed analytical method was applied for determination of PFCs in surface water from East Lake (Wuhan, China). The total concentrations of nine PFCs ranged from 30.12 to 125.35 ng L−1, with perfluorooctane sulfonate and perfluoroctanoic acid as the most prevalent PFCs, and the greatest concentrations of PFCs were observed in Niuchao lakelet. The concentrations of the PFCs (C ≥ 11) were mostly less than the limits of quantification (LOQs), attributed to the possibility that the more hydrophobic long-chain PFCs are potential to accumulate in sediment and aquatic biota. PMID:27966658

Occurrence investigation of perfluorinated compounds in surface water from East Lake (Wuhan, China) upon rapid and selective magnetic solid-phase extraction

NASA Astrophysics Data System (ADS)

Zhou, Yusun; Tao, Yun; Li, Huarong; Zhou, Tingting; Jing, Tao; Zhou, Yikai; Mei, Surong

2016-12-01

Using a novel magnetic nanocomposite as adsorbent, a convenient and effective magnetic solid-phase extraction (MSPE) procedure was established for selective separation and concentration of nine perfluorinated compounds (PFCs) in surface water sample. Then an ultra high-performance liquid chromatography-tandem mass spectrometry (UPLC-MS/MS) system was employed for detection of PFCs. Good linearity of the developed analytical method was in the range of 0.5-100 ng L-1 with R2 > 0.9917, and the limits of detection (LODs) ranged from 0.029 to 0.099 ng L-1. At three fortified concentrations of 0.5, 5 and 50 ng L-1, the spiked recoveries of PFCs were in the range of 90.05-106.67% with RSDs < 12.62% (n = 3). The proposed analytical method was applied for determination of PFCs in surface water from East Lake (Wuhan, China). The total concentrations of nine PFCs ranged from 30.12 to 125.35 ng L-1, with perfluorooctane sulfonate and perfluoroctanoic acid as the most prevalent PFCs, and the greatest concentrations of PFCs were observed in Niuchao lakelet. The concentrations of the PFCs (C ≥ 11) were mostly less than the limits of quantification (LOQs), attributed to the possibility that the more hydrophobic long-chain PFCs are potential to accumulate in sediment and aquatic biota.

The Application of TD/GC/NICI-MS with an Al2O3-PLOT-S Column for the Determination of Perfluoroalkylcycloalkanes in the Atmosphere.

PubMed

Ren, Yu; Schlager, Hans; Martin, Damien

2014-01-01

A modified method for the quantitative determination of atmospheric perfluoroalkylcycloalkanes (PFCs) using thermal desorption coupled with gas chromatography and detection by negative ion chemical ionization-mass spectrometry was developed. Using an optimized analytical system, a commercially available Al 2 O 3 porous layer open tubular (PLOT) capillary column (30 m × 0.25 mm) deactivated with Na 2 SO 4 was used for separation of PFCs. Improvements in the separation of PFCs, the corresponding identification and the limit of detection of PFCs using this method and column are presented. The method was successfully applied to determine the atmospheric background concentrations of a range of PFCs from a number of samples collected at a rural site in Germany. The results of this study suggest that the method outlined using the Al 2 O 3 -PLOT-S capillary column has good sensitivity and selectivity, and that it can be deployed in a routine laboratory process for the analysis of PFCs in the future research work. In addition, the ability of this column to separate the isomers of one of the lower boiling PFCs (perfluorodimethylcyclobutane) and its ability to resolve perfluoroethylcyclohexane offer the opportunity for single-column analysis for multiple PFCs.

Aquatic passive sampling of perfluorinated chemicals with polar organic chemical integrative sampler and environmental factors affecting sampling rate.

PubMed

Li, Ying; Yang, Cunman; Bao, Yijun; Ma, Xueru; Lu, Guanghua; Li, Yi

2016-08-01

A modified polar organic chemical integrative sampler (POCIS) could provide a convenient way of monitoring perfluorinated chemicals (PFCs) in water. In the present study, the modified POCIS was calibrated to monitor PFCs. The effects of water temperature, pH, and dissolved organic matter (DOM) on the sampling rate (R s) of PFCs were evaluated with a static renewal system. During laboratory validation over a 14-day period, the uptake kinetics of PFCs was linear with the POCIS. DOM and water temperature slightly influenced POCIS uptake rates, which is in consistent with the theory for uptake into POCIS. Therefore, within a narrow span of DOM and water temperatures, it was unnecessary to adjust the R s value for POCIS. Laboratory experiments were conducted with water over pH ranges of 3, 7, and 9. The R s values declined significantly with pH increase for PFCs. Although pH affected the uptake of PFCs, the effect was less than twofold. Application of the R s value to analyze PFCs with POCIS deployed in the field provided similar concentrations obtained from grab samples.

Lithium As Plasma Facing Component for Magnetic Fusion Research

DOE Office of Scientific and Technical Information (OSTI.GOV)

Masayuki Ono

The use of lithium in magnetic fusion confinement experiments started in the 1990's in order to improve tokamak plasma performance as a low-recycling plasma-facing component (PFC). Lithium is the lightest alkali metal and it is highly chemically reactive with relevant ion species in fusion plasmas including hydrogen, deuterium, tritium, carbon, and oxygen. Because of the reactive properties, lithium can provide strong pumping for those ions. It was indeed a spectacular success in TFTR where a very small amount (~ 0.02 gram) of lithium coating of the PFCs resulted in the fusion power output to improve by nearly a factor ofmore » two. The plasma confinement also improved by a factor of two. This success was attributed to the reduced recycling of cold gas surrounding the fusion plasma due to highly reactive lithium on the wall. The plasma confinement and performance improvements have since been confirmed in a large number of fusion devices with various magnetic configurations including CDX-U/LTX (US), CPD (Japan), HT-7 (China), EAST (China), FTU (Italy), NSTX (US), T-10, T-11M (Russia), TJ-II (Spain), and RFX (Italy). Additionally, lithium was shown to broaden the plasma pressure profile in NSTX, which is advantageous in achieving high performance H-mode operation for tokamak reactors. It is also noted that even with significant applications (up to 1,000 grams in NSTX) of lithium on PFCs, very little contamination (< 0.1%) of lithium fraction in main fusion plasma core was observed even during high confinement modes. The lithium therefore appears to be a highly desirable material to be used as a plasma PFC material from the magnetic fusion plasma performance and operational point of view. An exciting development in recent years is the growing realization of lithium as a potential solution to solve the exceptionally challenging need to handle the fusion reactor divertor heat flux, which could reach 60 MW/m2 . By placing the liquid lithium (LL) surface in the path of the main divertor heat flux (divertor strike point), the lithium is evaporated from the surface. The evaporated lithium is quickly ionized by the plasma and the ionized lithium ions can provide a strongly radiative layer of plasma ("radiative mantle"), thus could significantly reduce the heat flux to the divertor strike point surfaces, thus protecting the divertor surface. The protective effects of LL have been observed in many experiments and test stands. As a possible reactor divertor candidate, a closed LL divertor system is described. Finally, it is noted that the lithium applications as a PFC can be quite flexible and broad. The lithium application should be quite compatible with various divertor configurations, and it can be also applied to protecting the presently envisioned tungsten based solid PFC surfaces such as the ones for ITER. Lithium based PFCs therefore have the exciting prospect of providing a cost effective flexible means to improve the fusion reactor performance, while providing a practical solution to the highly challenging divertor heat handling issue confronting the steadystate magnetic fusion reactors.« less

The Role of Air-Electrode Structure on the Incorporation of Immiscible PFCs in Nonaqueous Li-O2 Battery.

PubMed

Balaish, Moran; Ein-Eli, Yair

2017-03-22

Perfluorocarbons (PFCs) are considered advantageous additives to nonaqueous Li-O 2 battery due to their superior oxygen solubility and diffusivity compared to common battery electrolytes. Up to now, the main focus was concentrated on PFCs-electrolyte investigation; however, no special attention was granted to the role of carbon structure in the PFCs-Li-O 2 system. In our current research, immiscible PFCs, rather than miscible fluorinated ethers, were added to activated carbon class air electrode due to their higher susceptibility toward O 2 •- attack and to their ability to shift the reaction from two-phase to an artificial three-phase reaction zone. The results showed superior battery performance upon PFCs addition at lower current density (0.05 mA cm -2 ) but unexpectedly failed to do so at higher current density (0.1 and 0.2 mA cm -2 ), where oxygen transport limitation is best illustrated. The last was a direct result of liquid-liquid displacement phenomenon occurring when the two immiscible liquids were introduced into the porous carbon medium. The investigation and role of carbon structure on the mechanism upon PFCs addition to Li-O 2 system are suggested based on electrochemical characterization, wettability behavior studies, and the physical adsorption technique. Finally, we suggest an optimum air-electrode structure enabling the incorporation of immiscible PFCs in a nonaqueous Li-O 2 battery.

Sorption of Perfluorochemicals to Matrices Relevant to Sites Impacted by Aqueous Film-Forming Foam

NASA Astrophysics Data System (ADS)

Sepulvado, J.; Higgins, C.

2011-12-01

Perfluorochemicals are a class of emerging contaminants consisting of fluorinated surfactants that are chemically and thermally stable and which contain a fluorocarbon tail that is both hydro- and oleophobic. Because of these unique properties, PFCs have a wide variety of uses including food paper packaging products, stain repellants, nonstick coatings, and aqueous film-forming foams (AFFF). At fire-training facilities, repeated application of AFFF is used to extinguish hydrocarbon fuel fires ignited for training purposes. The presence of perfluochemicals (PFCs) in groundwater as a result of repeated AFFF application at these facilities has been documented. Due to factors such as the recent push towards regulation of PFCs in drinking water, concerns have arisen about the fate of these compounds in the subsurface. Groundwater plumes containing PFC subclasses such as perfluorocarboxylic acids (PFCAs), perfluoroalkylsulfonates (PFAS), and fluorotelomer sulfonates (FtSs) in the μg/L to mg/L range have been detected. These plumes also may contain co-contaminants such as hydrocarbon fuel components and chlorinated solvents, some of which may exist as nonaqueous phase liquids (NAPL). This study examined the sorption of PFCs to soil and aquifer material across the concentration range applicable to AFFF-impacted sites (μg/L - mg/L) and looked at the impact of co-contaminants, including NAPL, on PFC sorption. PFC sorption was variable and indicated that similar to previous work on PFC sorption to sediment, subsurface PFC transport will depend on factors such as the sorbent organic carbon content, PFC subclass, solution chemistry, and PFC chain length.

Tetrahydrofuran-water extraction, in-line clean-up and selective liquid chromatography/tandem mass spectrometry for the quantitation of perfluorinated compounds in food at the low picogram per gram level.

PubMed

Ballesteros-Gómez, Ana; Rubio, Soledad; van Leeuwen, Stefan

2010-09-17

A new solvent extraction system was developed for extraction of PFCs from food. The extraction is carried out with 75:25 (v/v) tetrahydrofuran:water, a solvent mixture that provides an appropriate balance of hydrogen bonding, dispersion and dipole-dipole interactions to efficiently extract PFCs with chains containing 4-14 carbon atoms from foods. This mixture provided recoveries above 85% from foods including vegetables, fruits, fish, meat and bread; and above 75% from cheese. Clean-up with a weak anion exchange resin and Envi-carb SPE, which were coupled in line for simplicity, was found to minimize matrix effects (viz. enhancement or suppression of electrospray ionization). The target analytes (PFCs) were resolved on a perfluorooctyl phase column that proved effective in separating mass interferences for perfluorooctane sulfonate (PFOS) in fish and meat samples. The mass spectrometer was operated in the negative electrospray ionization mode and used to record two transitions per analyte and one per mass-labeled method internal standard. The target PFCs were quantified from solvent based calibration curves. The limits of detection (LODs) were as low as 1-5 pg analyte g(-1) food; by exception, those for C(4) and C(5) PFCs were somewhat higher (25-30 pg g(-1)) owing to their less favourable mass response. To the best of our knowledge these are among the best LODs for PFCs in foods reported to date. The analysis of a variety of foods revealed contamination with PFCs at levels from 4.5 to 75 pg g(-1) in 25% of samples (fish and packaged spinach). C(10)-C(14) PFCs were found in fish, which testifies to the need to control long-chain PFCs in this type of food. The proposed method is a useful tool for the development of a large-scale database for the presence of PFCs in foods. 2010 Elsevier B.V. All rights reserved.

Pair-flowered cymes in the Lamiales: structure, distribution and origin

PubMed Central

Weber, Anton

2013-01-01

Background and Aims In the Lamiales, indeterminate thyrses (made up of axillary cymes) represent a significant inflorescence type. However, it has been largely overlooked that there occur two types of cymes: (1) ordinary cymes, and (2) ‘pair-flowered cymes’ (PFCs), with a flower pair (terminal and front flower) topping each cyme unit. PFCs are unique to the Lamiales and their distribution, origin and phylogeny are not well understood. Methods The Lamiales are screened as to the occurrence of PFCs, ordinary cymes and single flowers (constituting racemic inflorescences). Key Results PFCs are shown to exhibit a considerable morphological and developmental diversity and are documented to occur in four neighbouring taxa of Lamiales: Calceolariaceae, Sanango, Gesneriaceae and Plantaginaceae. They are omnipresent in the Calceolariaceae and almost so in the Gesneriaceae. In the Plantaginaceae, PFCs are restricted to the small sister tribes Russelieae and Cheloneae (while the large remainder has single flowers in the leaf/bract axils; ordinary cymes do not occur). Regarding the origin of PFCs, the inflorescences of the genus Peltanthera (unplaced as to family; sister to Calceolariaceae, Sanango and Gesneriaceae in most molecular phylogenies) support the idea that PFCs have originated from paniculate systems, with the front-flowers representing remnant flowers. Conclusions From the exclusive occurrence of PFCs in the Lamiales and the proximity of the respective taxa in molecular phylogenies it may be expected that PFCs have originated once, representing a synapomorphy for this group of taxa and fading out within the Plantaginaceae. However, molecular evidence is ambiguous. Depending on the position of Peltanthera (depending in turn on the kind and number of genes and taxa analysed) a single, a double (the most probable scenario) or a triple origin appears conceivable. PMID:23884395

Neurotoxic effects of perfluoroalkylated compounds: mechanisms of action and environmental relevance.

PubMed

Mariussen, Espen

2012-09-01

Perfluoroalkylated compounds (PFCs) are used in fire-fighting foams, treatment of clothes, carpets and leather products, and as lubricants, pesticides, in paints and medicine. Recent developments in chemical analysis have revealed that fluorinated compounds have become ubiquitously spread and are regarded as a potential threats to the environment. Due to the carbon-fluorine bond, which has a very high bond strength, these chemicals are extremely persistent towards degradation and some PFCs have a potential for bioaccumulation in organisms. Of particular concern has been the developmental toxicity of PFOS and PFOA, which has been manifested in rodent studies as high mortality of prenatally exposed newborn rats and mice within 24 h after delivery. The nervous system appears to be one of the most sensitive targets of environmental contaminants. The serious developmental effects of PFCs have lead to the upcoming of studies that have investigated neurotoxic effects of these substances. In this review the major findings of the neurotoxicity of the main PFCs and their suggested mechanisms of action are presented. The neurotoxic effects are discussed in light of other toxic effects of PFCs to indicate the significance of PFCs as neurotoxicants. The main findings are that PFCs may induce neurobehavioral effects, particularly in developmentally exposed animals. The effects are, however, subtle and inconclusive and are often induced at concentrations where other toxic effects also are expected. Mechanistic studies have shown that PFCs may affect the thyroid system, influence the calcium homeostasis, protein kinase C, synaptic plasticity and cellular differentiation. Compared to other environmental toxicants the human blood levels of PFCs are high and of particular concern is that susceptible groups may be exposed to a cocktail of substances that in combination reach harmful concentrations.

Determination of perfluorinated compounds (PFCs) in various foodstuff packaging materials used in the Greek market.

PubMed

Zafeiraki, Effrosyni; Costopoulou, Danae; Vassiliadou, Irene; Bakeas, Evangelos; Leondiadis, Leondios

2014-01-01

Perfluorinated compounds (PFCs) are used in food packaging materials as coatings/additives for oil and moisture resistance. In the current study, foodstuff-packaging materials collected from the Greek market, made of paper, paperboard or aluminum foil were analyzed for the determination of PFCs. For the analysis of the samples, pressurized liquid extraction (PLE), liquid chromatography–tandem mass spectrometry (LC–MS/MS) and isotope dilution method were applied to develop a specific and sensitive method of analysis for the quantification of 12 PFCs: perfluorobutanoic acid (PFBA), perfluoropentanoic acid (PFPeA), perfluorohexanoic acid (PFHxA), perfluoroheptanoic acid (PFHpA), perfluorooctanoic acid (PFOA), perfluorononanoic acid (PFNA), perfluorodecanoic acid (PFDA), perfluoroundecanoic acid (PFUnDA), perfluorododecanoic acid (PFDoA), perfluorobutane sulfonate (PFBS), perfluorohexane sulfonate (PFHxS) and perfluorooctane sulfonate (PFOS) and the qualitative detection of 5 more: perfluorotridecanoic acid (PFTrDA), perfluorotetradecanoic acid (PFTeDA), perflyohexadecanoic acid (PFHxDA), perfluorooctadecanoic acid (PFODA) and perfluorodecane sulfonate (PFDS). No PFCs were quantified in aluminum foil wrappers, baking paper materials or beverage cups. PFTrDA, PFTeDA and PFHxDA were detected in fast food boxes. In the ice cream cup sample only PFHxA was found. On the other hand, several PFCs were quantified and detected in fast food wrappers, while the highest levels of PFCs were found in the microwave popcorn bag. PFOA and PFOS were not detected in any of the samples. Compared to other studies from different countries, very low concentrations of PFCs were detected in the packaging materials analyzed. Our results suggest that probably no serious danger for consumers’ health can be associated with PFCs contamination of packaging materials used in Greece.

Overview of decade-long development of plasma-facing components at ASIPP

NASA Astrophysics Data System (ADS)

Luo, G.-N.; Liu, G. H.; Li, Q.; Qin, S. G.; Wang, W. J.; Shi, Y. L.; Xie, C. Y.; Chen, Z. M.; Missirlian, M.; Guilhem, D.; Richou, M.; Hirai, T.; Escourbiac, F.; Yao, D. M.; Chen, J. L.; Wang, T. J.; Bucalossi, J.; Merola, M.; Li, J. G.; EAST Team

2017-06-01

The first EAST (Experimental Advanced Superconducting Tokamak) plasma ignited in 2006 with non-actively cooled steel plates as the plasma-facing materials and components (PFMCs) which were then upgraded into full graphite tiles bolted onto water-cooled copper heat sinks in 2008. The first wall was changed further into molybdenum alloy in 2012, while keeping the graphite for both the upper and lower divertors. With the rapid increase in heating and current driving power in EAST, the W/Cu divertor project was launched around the end of 2012, aiming at achieving actively cooled full W/Cu-PFCs for the upper divertor, with heat removal capability up to 10 MW m-2. The W/Cu upper divertor was finished in the spring of 2014, consisting of 80 cassette bodies toroidally assembled. Commissioning of the EAST upper W/Cu divertor in 2014 was unsatisfactory and then several practical measures were implemented to improve the design, welding quality and reliability, which helped us achieve successful commissioning in the 2015 Spring Campaign. In collaboration with the IO and CEA teams, we have demonstrated our technological capability to remove heat loads of 5000 cycles at 10 MW m-2 and 1000 cycles at 20 MW m-2 for the small scale monoblock mockups, and surprisingly over 300 cycles at 20 MW m-2 for the flat-tile ones. The experience and lessons we learned from batch production and commissioning are undoubtedly valuable for ITER (International Thermonuclear Experimental Reactor) engineering validation and tungsten-related plasma physics.

Polyfluoroalkyl compounds in the aquatic environment: a review of their occurrence and fate.

PubMed

Ahrens, Lutz

2011-01-01

The occurrence and fate of polyfluoroalkyl compounds (PFCs) in the aquatic environment has been recognized as one of the emerging issues in environmental chemistry. PFCs comprise a diverse group of chemicals that are widely used as processing additives during fluoropolymer production and as surfactants in consumer applications for over 50 years. PFCs are known to be persistent, bioaccumulative and have possible adverse effects on humans and wildlife. As a result, perfluorooctane sulfonate (PFOS) has been added to the persistent organic pollutants (POPs) list of the Stockholm Convention in May 2009. However, their homologues, neutral precursor compounds and new PFCs classes continue to be produced. In general, several PFCs from different classes have been detected ubiquitously in the aqueous environment while the concentrations usually range between pg and ng per litre for individual compounds. Sources of PFCs into the aqueous environment are both point sources (e.g., wastewater treatment plant effluents) and nonpoint sources (e.g., surface runoff). The detected congener composition in environmental samples depends on their physicochemical characteristics and may provide information to their sources and transport pathways. However, the dominant transport pathways of individual PFCs to remote regions have not been conclusively characterised to date. The objective of this article is to give an overview on existing knowledge of the occurrence, fate and processes of PFCs in the aquatic environment. Finally, this article identifies knowledge gaps, presents conclusions and recommendations for future work.

Bulk ion heating with ICRF waves in tokamaks

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mantsinen, M. J., E-mail: mervi.mantsinen@bsc.es; Barcelona Supercomputing Center, Barcelona; Bilato, R.

2015-12-10

Heating with ICRF waves is a well-established method on present-day tokamaks and one of the heating systems foreseen for ITER. However, further work is still needed to test and optimize its performance in fusion devices with metallic high-Z plasma facing components (PFCs) in preparation of ITER and DEMO operation. This is of particular importance for the bulk ion heating capabilities of ICRF waves. Efficient bulk ion heating with the standard ITER ICRF scheme, i.e. the second harmonic heating of tritium with or without {sup 3}He minority, was demonstrated in experiments carried out in deuterium-tritium plasmas on JET and TFTR andmore » is confirmed by ICRF modelling. This paper focuses on recent experiments with {sup 3}He minority heating for bulk ion heating on the ASDEX Upgrade (AUG) tokamak with ITER-relevant all-tungsten PFCs. An increase of 80% in the central ion temperature T{sub i} from 3 to 5.5 keV was achieved when 3 MW of ICRF power tuned to the central {sup 3}He ion cyclotron resonance was added to 4.5 MW of deuterium NBI. The radial gradient of the T{sub i} profile reached locally values up to about 50 keV/m and the normalized logarithmic ion temperature gradients R/LT{sub i} of about 20, which are unusually large for AUG plasmas. The large changes in the T{sub i} profiles were accompanied by significant changes in measured plasma toroidal rotation, plasma impurity profiles and MHD activity, which indicate concomitant changes in plasma properties with the application of ICRF waves. When the {sup 3}He concentration was increased above the optimum range for bulk ion heating, a weaker peaking of the ion temperature profile was observed, in line with theoretical expectations.« less

An analytical expression for ion velocities at the wall including the sheath electric field and surface biasing for erosion modeling at JET ILW

DOE PAGES

Borodkina, I.; Borodin, D.; Brezinsek, S.; ...

2017-04-12

For simulation of plasma-facing component erosion in fusion experiments, an analytical expression for the ion velocity just before the surface impact including the local electric field and an optional surface biasing effect is suggested. Energy and angular impact distributions and the resulting effective sputtering yields were produced for several experimental scenarios at JET ILW mostly involving PFCs exposed to an oblique magnetic field. The analytic solution has been applied as an improvement to earlier ERO modelling of localized, Be outer limiter, RF-enhanced erosion, modulated by toggling of a remote, however magnetically connected ICRH antenna. The effective W sputtering yields duemore » to D and Be ion impact in Type-I and Type-III ELMs and inter-ELM conditions were also estimated using the analytical approach and benchmarked by spectroscopy. The intra-ELM W sputtering flux increases almost 10 times in comparison to the inter-ELM flux.« less

Development of CVD-W coatings on CuCrZr and graphite substrates with a PVD intermediate layer

NASA Astrophysics Data System (ADS)

Song, Jiupeng; Lian, Youyun; Lv, Yanwei; Liu, Junyong; Yu, Yang; Liu, Xiang; Yan, Binyou; Chen, Zhigang; Zhuang, Zhigang; Zhao, Ximeng; Qi, Yang

2014-12-01

In order to apply tungsten (W) coatings by chemical vapor deposition (CVD) for repairing or updating the plasma facing components (PFCs) of the first wall and divertor in existing or future tokomaks, where CuCrZr or graphite is the substrate material, an intermediate layer by physical vapor deposition (PVD) has been used to accommodate the interface stress due to the mismatch of thermal expansion or act as a diffusion barrier between the CVD-W coating and the substrate. The prepared CuCrZr/PVD-Cu/CVD-W sample with active cooling has passed thermal fatigue tests by electron beam with an absorbed power of 2.2 MW/m2, 50 s on/50 s off, for 100 cycles. Another graphite/PVD-Si/CVD-W sample without active cooling underwent thermal fatigue testing with an absorbed power density of 4.62 MW/m2, 5 s on/25 s off, for 200 cycles, and no catastrophic failure was found.

Plasma Surface Interactions Common to Advanced Fusion Wall Materials and EUV Lithography - Lithium and Tin

NASA Astrophysics Data System (ADS)

Ruzic, D. N.; Alman, D. A.; Jurczyk, B. E.; Stubbers, R.; Coventry, M. D.; Neumann, M. J.; Olczak, W.; Qiu, H.

2004-09-01

Advanced plasma facing components (PFCs) are needed to protect walls in future high power fusion devices. In the semiconductor industry, extreme ultraviolet (EUV) sources are needed for next generation lithography. Lithium and tin are candidate materials in both areas, with liquid Li and Sn plasma material interactions being critical. The Plasma Material Interaction Group at the University of Illinois is leveraging liquid metal experimental and computational facilities to benefit both fields. The Ion surface InterAction eXperiment (IIAX) has measured liquid Li and Sn sputtering, showing an enhancement in erosion with temperature for light ion bombardment. Surface Cleaning of Optics by Plasma Exposure (SCOPE) measures erosion and damage of EUV mirror samples, and tests cleaning recipes with a helicon plasma. The Flowing LIquid surface Retention Experiment (FLIRE) measures the He and H retention in flowing liquid metals, with retention coefficients varying between 0.001 at 500 eV to 0.01 at 4000 eV.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ekedahl, Annika, E-mail: annika.ekedahl@cea.fr; Bourdelle, Clarisse; Artaud, Jean-François

The longstanding expertise of the Tore Supra team in long pulse heating and current drive with radiofrequency (RF) systems will now be exploited in the WEST device (tungsten-W Environment in Steady-state Tokamak) [1]. WEST will allow an integrated long pulse tokamak programme for testing W-divertor components at ITER-relevant heat flux (10-20 MW/m{sup 2}), while treating crucial aspects for ITER-operation, such as avoidance of W-accumulation in long discharges, monitoring and control of heat fluxes on the metallic plasma facing components (PFCs) and coupling of RF waves in H-mode plasmas. Scenario modelling using the METIS-code shows that ITER-relevant heat fluxes are compatiblemore » with the sustainment of long pulse H-mode discharges, at high power (up to 15 MW / 30 s at I{sub P} = 0.8 MA) or high fluence (up to 10 MW / 1000 s at I{sub P} = 0.6 MA) [2], all based on RF heating and current drive using Ion Cyclotron Resonance Heating (ICRH) and Lower Hybrid Current Drive (LHCD). This paper gives a description of the ICRH and LHCD systems in WEST, together with the modelling of the power deposition of the RF waves in the WEST-scenarios.« less

METHOD DEVELOPMENT FOR THE DETERMINATION OF PERFLUORINATED ORGANIC COMPOUNDS ( PFCS ) IN SURFACE WATER

EPA Science Inventory

The method for the determination of perfluorinated organic compounds (PFCs) in surface water has been developed and applied to natural water. The method shows an adequate sensitivity, precision and accuracy for ten kinds of target compounds. These PFCs were found in most samples...

In vitro characterization of the immunotoxic potential of several perfluorinated compounds (PFCs)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Corsini, Emanuela, E-mail: emanuela.corsini@unimi.it; Sangiovanni, Enrico; Avogadro, Anna

2012-01-15

We have previously shown that PFOA and PFOS directly suppress cytokine secretion in immune cells, with different mechanisms of action. In particular, we have demonstrated a role for PPAR-α in PFOA-induced immunotoxicity, and that PFOS has an inhibitory effect on LPS-induced I-κB degradation. These studies investigate the immunomodulatory effects of four other PFCs, namely PFBS, PFOSA, PFDA, and fluorotelomer using in vitro assays. The release of the pro-inflammatory cytokines IL-6 and TNF-α was evaluated in lipolysaccharide (LPS)-stimulated human peripheral blood leukocytes (hPBL) and in the human promyelocytic cell line THP-1, while the release of IL-10 and IFN-γ was evaluated inmore » phytohemagglutinin (PHA)-stimulated hPBL. All PFCs suppressed LPS-induced TNF-α production in hPBL and THP-1 cells, while IL-6 production was suppressed by PFOSA, PFOS, PFDA and fluorotelomer. PFBS, PFOSA, PFOS, PFDA and fluorotelomer inhibited PHA-induced IL-10 release, while IFN-γ secretion was affected by PFOSA, PFOS, PFDA and fluorotelomer. Leukocytes obtained from female donors appear to be more sensitive to the in vitro immunotoxic effects of PFCs when their responses are compared to the results obtained using leukocytes from male donors. Mechanistic investigations demonstrated that inhibition of TNF-α release in THP-1 cells occurred at the transcriptional level. All PFCs, including PFOA and PFOS, decreased LPS-induced NF-κB activation. With the exception of PFOA, none of the PFCs tested was able to activate PPARα driven transcription in transiently transfected THP-1 cells, excluding a role for PPARα in the immunomodulation observed. PFBS and PFDA prevented LPS-induced I-κB degradation. Overall, these studies suggest that PFCs affect NF-κB activation, which directly suppresses cytokine secretion by immune cells. Our results indicate that PFOA is the least active of the PFCs examined followed by PFBS, PFDA, PFOS, PFOSA and fluorotelomer. -- Research Highlights: ► PFCs showed direct immunomodulatory properties and inhibition of NF-κB driven transcription. ► PFOA is the least active PFCs followed by PFBS, PFDA, PFOS, PFOSA and fluorotelomer. ► Only PFOA activates PPARalpha.« less

40 CFR Appendix A to Subpart G of... - Substitutes Subject to Use Restrictions and Unacceptable Substitutes

Code of Federal Regulations, 2011 CFR

2011-07-01

... characteristic of concern for PFCs is that they have long atmospheric lifetimes and high global warming potentials. Although actual contributions to global warming depend upon the quantities of PFCs emitted, the... characteristic of concern for PFCs is that they have long atmospheric lifetimes and high global warming...

40 CFR Appendix A to Subpart G of... - Substitutes Subject to Use Restrictions and Unacceptable Substitutes

Code of Federal Regulations, 2014 CFR

2014-07-01

... characteristic of concern for PFCs is that they have long atmospheric lifetimes and high global warming potentials. Although actual contributions to global warming depend upon the quantities of PFCs emitted, the... for PFCs is that they have long atmospheric lifetimes and high global warming potentials. Although...

40 CFR Appendix A to Subpart G of... - Substitutes Subject to Use Restrictions and Unacceptable Substitutes

Code of Federal Regulations, 2012 CFR

2012-07-01

... characteristic of concern for PFCs is that they have long atmospheric lifetimes and high global warming potentials. Although actual contributions to global warming depend upon the quantities of PFCs emitted, the... characteristic of concern for PFCs is that they have long atmospheric lifetimes and high global warming...

40 CFR Appendix A to Subpart G of... - Substitutes Subject to Use Restrictions and Unacceptable Substitutes

Code of Federal Regulations, 2013 CFR

2013-07-01

... characteristic of concern for PFCs is that they have long atmospheric lifetimes and high global warming potentials. Although actual contributions to global warming depend upon the quantities of PFCs emitted, the... characteristic of concern for PFCs is that they have long atmospheric lifetimes and high global warming...

PERFLUORINATED COMPOUNDS: EMERGING POPs WITH POTENTIAL IMMUNOTOXICITY

PubMed Central

Corsini, Emanuela; Luebke, Robert W.; Germolec, Dori R.; DeWitt, Jamie C.

2015-01-01

Perfluorinated compounds (PFCs) have been recognized as an important class of environmental contaminants commonly detected in blood samples of both wildlife and humans. These compounds have been in use for more than 60 years as surface treatment chemicals, polymerization aids, and surfactants. They possess a strong carbon-fluorine bond, which leads to their environmental persistence. There is evidence from both epidemiology and laboratory studies that PFCs may be immunotoxic, affecting both cell-mediated and humoral immunity. Reported effects of PFCs include decreased spleen and thymus weights and cellularity, reduced antibody production, reduced survival after influenza infection, and altered cytokine production. Immunosuppression is a critical effect associated with exposure to PFCs, as it has been reported to reduce antibody responses to vaccination in children. Mounting evidence suggests that immunotoxicity in experimental animals can occur at serum concentrations below, within, or just above the reported range for highly exposed humans and wildlife. Considering bioaccumulation and exposure to multiple PFCs, the risk of immunotoxicity for humans and wildlife cannot be discounted. This review will discuss current and recently published work exploring the immunomodulatory effects of PFCs in experimental animals and humans. PMID:24503008

Skipjack tuna as a bioindicator of contamination by perfluorinated compounds in the oceans.

PubMed

Hart, Kimberly; Kannan, Kurunthachalam; Tao, Lin; Takahashi, Shin; Tanabe, Shinsuke

2008-09-15

Perfluorinated chemicals (PFCs) have emerged as global environmental contaminants. Studies have reported the widespread occurrence of PFCs in biota from marine coastal waters and in remote polar regions. However, few studies have reported the distribution of PFCs in biota from offshore waters and open oceans. In this study, concentrations of nine PFCs were determined in the livers of 60 skipjack tuna (Katsuwonus pelamis) collected from offshore waters and the open ocean along the Pacific Rim, including the Sea of Japan, the East China Sea, the Indian Ocean, and the Western North Pacific Ocean, during 1997-1999. At least one of the nine PFCs was found in every tuna sample analyzed. Overall, perfluorooctanesulfonate (PFOS) and perfluoroundecanoic acid (PFUnDA) were the predominant compounds found in livers of tuna at concentrations of <1-58.9 and <1-31.6 ng/g, wet wt, respectively. Long-chain perfluorocarboxylates such as perfluorodecanoic acid (PFDA) and perfluorododecanoic acid (PFDoDA) were common in the tuna livers. In livers of tuna from several offshore and open-ocean locations, concentrations of PFUnDA were greater than the concentrations of PFOS. The profiles and concentrations of PFCs in tuna livers suggest that the sources in East Asia are dominated by long-chain perfluorocarboxylates, especially PFUnDA. High concentrations of PFUnDA in tuna may indicate a shift in sources of PFCs in East Asia. The spatial distribution of PFOS in skipjack tuna reflected the concentrations previously reported in seawater samples from the Pacific and Indian Oceans, suggesting that tuna are good bioindicators of pollution by PFOS. Despite its predominance in ocean waters, PFOA was rarely found in tuna livers, indicative of the low bioaccumulation potential of this compound. Our study establishes baseline concentrations of PFCs in skipjack tuna from the oceans of the Asia-Pacific region, enabling future temporal trend studies of PFCs in oceans.

Perfluorocarbons (PFCs), Some of the Immortal Molecules in the Earth's Atmosphere

ERIC Educational Resources Information Center

Shallcross, Dudley E.; Martin, Damien

2011-01-01

Perfluorocarbons (PFCs) are fully fluorinated hydrocarbons that are used as blood plasma substitutes, in medical imaging and in the cosmetics industry. Most are inert and can also be used as tracers for applications such as air flow. However, because of their C-F bonds and their longevity in the atmosphere, PFCs have large global warming…

Structure-dependent binding and activation of perfluorinated compounds on human peroxisome proliferator-activated receptor γ

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, Lianying; College of Life Science, Dezhou University, Dezhou 253023; Ren, Xiao-Min

2014-09-15

Perfluorinated compounds (PFCs) have been shown to disrupt lipid metabolism and even induce cancer in rodents through activation of peroxisome proliferator-activated receptors (PPARs). Lines of evidence showed that PPARα was activated by PFCs. However, the information on the binding interactions between PPARγ and PFCs and subsequent alteration of PPARγ activity is still limited and sometimes inconsistent. In the present study, in vitro binding of 16 PFCs to human PPARγ ligand binding domain (hPPARγ-LBD) and their activity on the receptor in cells were investigated. The results showed that the binding affinity was strongly dependent on their carbon number and functional group.more » For the eleven perfluorinated carboxylic acids (PFCAs), the binding affinity increased with their carbon number from 4 to 11, and then decreased slightly. The binding affinity of the three perfluorinated sulfonic acids (PFSAs) was stronger than their PFCA counterparts. No binding was detected for the two fluorotelomer alcohols (FTOHs). Circular dichroim spectroscopy showed that PFC binding induced distinctive structural change of the receptor. In dual luciferase reporter assays using transiently transfected Hep G2 cells, PFCs acted as hPPARγ agonists, and their potency correlated with their binding affinity with hPPARγ-LBD. Molecular docking showed that PFCs with different chain length bind with the receptor in different geometry, which may contribute to their differences in binding affinity and transcriptional activity. - Highlights: • Binding affinity between PFCs and PPARγ was evaluated for the first time. • The binding strength was dependent on fluorinated carbon chain and functional group. • PFC binding induced distinctive structural change of the receptor. • PFCs could act as hPPARγ agonists in Hep G2 cells.« less

Biomonitoring of perfluorinated compounds in a drop of blood.

PubMed

Mao, Pan; Wang, Daojing

2015-06-02

Biomonitoring of pollutants and their metabolites and derivatives using biofluids provides new opportunities for spatiotemporal assessment of human risks to environmental exposures. Perfluorinated compounds (PFCs) have been used widely in industry and pose significant environmental concerns due to their stability and bioaccumulation in humans and animals. However, current methods for extraction and measurement of PFCs require relatively large volumes (over one hundred microliters) of blood samples, and therefore, are not suitable for frequent blood sampling and longitudinal biomonitoring of PFCs. We have developed a new microassay, enabled by our silicon microfluidic chip platform, for analyzing PFCs in small volumes (less than five microliters) of blood. Our assay integrates on-chip solid-phase extraction (SPE) with online nanoflow liquid chromatography-electrospray ionization-mass spectrometry (nanoLC-ESI-MS) detection. We demonstrated high sample recovery, excellent interday and intraday accuracy and precision, and a limit of detection down to 50 femtogram of PFCs, in one microliter of human plasma. We validated our assay performance using pooled human plasma and NIST SRM 1950 samples. Our microfluidic chip-based assay may enable frequent longitudinal biomonitoring of PFCs and other environmental toxins using a finger prick of blood, thereby providing new insights into their bioaccumulation, bioavailability, and toxicity.

Perfluorinated compounds affect the function of sex hormone receptors.

PubMed

Kjeldsen, Lisbeth Stigaard; Bonefeld-Jørgensen, Eva Cecilie

2013-11-01

Perfluorinated compounds (PFCs) are a large group of chemicals used in different industrial and commercial applications. Studies have suggested the potential of some PFCs to disrupt endocrine homeostasis, increasing the risk of adverse health effects. This study aimed to elucidate mechanisms behind PFC interference with steroid hormone receptor functions. Seven PFCs [perfluorohexane sulfonate (PFHxS), perfluorooctane sulfonate (PFOS), perfluorooctanoate (PFOA), perfluorononanoate (PFNA), perfluorodecanoate (PFDA), perfluoroundecanoate (PFUnA), and perfluorododecanoate (PFDoA)] were analyzed in vitro for their potential to affect estrogen receptor (ER) and androgen receptor (AR) transactivity as well as aromatase enzyme activity. The PFCs were assessed as single compounds and in an equimolar mixture. PFHxS, PFOS and PFOA significantly induced the ER transactivity, whereas PFHxS, PFOS, PFOA, PFNA and PFDA significantly antagonized the AR activity in a concentration-dependent manner. Moreover, PFDA weakly decreased the aromatase activity at a high test concentration. A mixture effect more than additive was observed on AR function. We conclude that five of the seven PFCs possess the potential in vitro to interfere with the function of the ER and/or the AR. The observed mixture effect emphasizes the importance of considering the combined action of PFCs in future studies to assess related health risks.

Method for enhancing microbial utilization rates of gases using perfluorocarbons

DOEpatents

Turick, Charles E.

1997-01-01

A method of enhancing the bacterial reduction of industrial gases using perfluorocarbons (PFCs) is disclosed. Because perfluorocarbons (PFCs) allow for a much greater solubility of gases than water does, PFCs have the potential to deliver gases in higher concentrations to microorganisms when used as an additive to microbial growth media thereby increasing the rate of the industrial gas conversion to economically viable chemicals and gases.

Electrocautery vs non-electrocautery dilation catheters in endoscopic ultrasonography-guided pancreatic fluid collection drainage

PubMed Central

Kitamura, Katsuya; Yamamiya, Akira; Ishii, Yu; Nomoto, Tomohiro; Honma, Tadashi; Yoshida, Hitoshi

2016-01-01

AIM: To investigate the safety and utility of an electrocautery dilation catheter for endoscopic ultrasonography (EUS)-guided pancreatic fluid collection drainage. METHODS: A single-center, exploratory, retrospective study was conducted between August 2010 and August 2014. This study was approved by the Medical Ethics Committee of our institution. Informed, written consent was obtained from each patient prior to the procedure. The subjects included 28 consecutive patients who underwent EUS-guided transmural drainage (EUS-TD) for symptomatic pancreatic and peripancreatic fluid collections (PFCs) by fine needle aspiration using a 19-gauge needle. These patients were retrospectively divided into two groups based on the use of an electrocautery dilation catheter as a fistula dilation device; 15 patients were treated with an electrocautery dilation catheter (electrocautery group), and 13 patients were treated with a non-electrocautery dilation catheter (non-electrocautery group). We evaluated the technical and clinical successes and the adverse events associated with EUS-TD for the treatment of PFCs between the two groups. RESULTS: There were no significant differences in age, sex, type, location and diameter of PFCs between the groups. Thirteen patients (87%) in the electrocautery group and 10 patients (77%) in the non-electrocautery group presented with infected PFCs. The technical success rates of EUS-TD for the treatment of PFCs were 100% (15/15) and 100% (13/13) for the electrocautery and the non-electrocautery groups, respectively. The clinical success rates of EUS-TD for the treatment of PFCs were 67% (10/15) and 69% (9/13) for the electrocautery and the non-electrocautery groups, respectively (P = 0.794). The procedure time of EUS-TD for the treatment of PFCs in the electrocautery group was significantly shorter than that of the non-electrocautery group (mean ± SD: 30 ± 12 min vs 52 ± 20 min, P < 0.001). Adverse events associated with EUS-TD for the treatment of PFCs occurred in 0 patients and 1 patient for the electrocautery and the non-electrocautery groups, respectively (P = 0.942). CONCLUSION: EUS-TD using an electrocautery dilation catheter as a fistula dilation device for the treatment of symptomatic PFCs appears safe and contributes to a shorter procedure time. PMID:27433292

Endoscopic Ultrasound-Guided Management of Pancreatic Fluid Collections: Update and Review of the Literature

PubMed Central

Alali, Ali; Mosko, Jeffrey; May, Gary; Teshima, Christopher

2017-01-01

Severe acute pancreatitis is often complicated by the development of pancreatic fluid collections (PFCs), which may be associated with significant morbidity and mortality. It is crucial to accurately classify these collections as a pseudocyst or walled-off necrosis (WON) given significant differences in outcomes and management. Interventions for PFCs have increasingly shifted to less invasive strategies, with endoscopic ultrasound (EUS)-guided methods being shown to be safer and equally effective as more invasive surgical techniques. In recent years, many new developments have improved the safety and efficacy of EUS-guided interventions, such as the introduction of lumen-apposing metal stents (LAMS), direct endoscopic necrosectomy (DEN) and multiple other adjunctive techniques. Despite these developments, treatment of PFCs, and infected WON in particular, continues to be associated with significant morbidity and mortality. In this article, we discuss the EUS-guided management of PFCs while reviewing the latest developments and controversies in the field. We end by summarizing our own approach to managing PFCs. PMID:28391671

Perfluorinated substances in human food and other sources of human exposure.

PubMed

D'Hollander, Wendy; de Voogt, Pim; De Coen, Wim; Bervoets, Lieven

2010-01-01

The widespread distribution and degradation of PFCs in the environment results in a very complex exposure pattern, which makes it difficult to define the relative contribution to human exposure from different exposure pathways. The present review is designed to provide an overview of the existing data on levels of PFCs measured in the human diet and in drinking water. Data on levels of PFCs in the human diet are rather scarce, but the level in the fish appear to be well documented. Among PFCs, PFOS and PFOA are the best studied compounds in fish from both experimental and monitoring studies. Recently, the number of publications that address other PFCs has increased, but the total number available is still limited. In general, we discovered that care should be exercised when using the reviewed data, because, in the majority of publications, quality control and/or details on analysis are, at least partly, lacking. It has been well documented that PFOA and PFOS have the potential to accumulate in fish and concentrations up to 7 and 170 ng/g wwt, respectively in edible fish species have been found. PFOS is the most crucial and prominent compound identified, followed by the PFOA. Also, in aquatic invertebrate such as shrimps, mussels, clams, and oysters, high PFOS levels have been reported (up to 387 ng/g wwt). However in most publications PFC level reported in molluscs were less than 1 ng/g wwt. Positive correlations were found between PFC body burden and self reported fish consumption. In recognition of the potential for human exposure to PFCs via fish consumption, the Minnesota Department of Health has recently issued fish consumption advisories for contaminated sections of the Mississippi River. It is interesting to note that 79% of the reviewed publications on PFCs in the whole fish homogenates exceed the that threshold. Moreover, five of the PFC concentration reported in muscles tissue exceeded the advisory level of 38 ng/g wwt. Even though several authors concluded that consumption of contaminated food and drinking water constitutes the major exposure pathway for humans, only a few reports on PFCs in composite food exist. Food can be contaminated in an indirect way, because PFCs are widely used in food-packaging coatings and cooking materials. On the other hand, PFCs can also enter food organisms via environmental routes such as inhalation or adsorption from air. In a few studies, composite samples, duplicate diet samples, or other food items were analyzed for several PFCs, PFOS and PFOA, PFHpA, PFHxA, and PFHxS were meAsured and displayed concentrations ranging from-detected up to 15 ng/g wwt. In one study, a very high PFOA concentration of 118 ng/g were reported, but overall, PFC levels are below 10 ng/g wwt. It is important to note that, among all studies reviewed, PFCs were found in a maximum of 50% of the analyzed samples and generally only in 10% or less of samples analyzed. In contrast to what is observed in fish and other food items PFOA levels in drinking water (ND - 50 ng/L) and other PFCs (1-3 ng/L). In one study, extremely high values (519 ng/L) were measured in drinking water of a contaminated area in the Ruhr region. In Spain, bottled water was analyzed and four PFCs (PFOA, PFNA,PFDA and PFHpA) were found at low levels (<1 ng/L). Because of higher levels found in drinking water at several locations, some provisional drinking water guideline values for PFOS and PFOA have already been established, e.g., in the UK, Bavaria, and Minnesota. Since PFCs are present both in food and drinking water, Tolerable Daily Intake values for PFOS and PFOA have also been proposed by several institutes in Europe and in the USA. The ingestion of dust through hand-to-mouth transfer from indoor house dust can also be a potential source of PFC exposure, especially for toddlers and children. In publications on PFCs in indoor dust, the mean PFOS and PFOA levels varied between 39 and 1,200 ng/g and between 11 and 220 ng/g, respectively. Overall, it is clear that there is still lack of PFC exposure data for food and beverages, which renders the assessment of the contribution of the diet to total human PFC exposure uncertain. It is, therefore, appropriate that several scientific projects have recently been launched that addresses the assessment of human exposure to PFCs and related compounds from dietary sources.

Method for enhancing microbial utilization rates of gases using perfluorocarbons

DOEpatents

Turick, C.E.

1997-06-10

A method of enhancing the bacterial reduction of industrial gases using perfluorocarbons (PFCs) is disclosed. Because perfluorocarbons (PFCs) allow for a much greater solubility of gases than water does, PFCs have the potential to deliver gases in higher concentrations to microorganisms when used as an additive to microbial growth media thereby increasing the rate of the industrial gas conversion to economically viable chemicals and gases. 3 figs.

Polyfluorinated compounds in dust from homes, offices, and vehicles as predictors of concentrations in office workers' serum.

PubMed

Fraser, Alicia J; Webster, Thomas F; Watkins, Deborah J; Strynar, Mark J; Kato, Kayoko; Calafat, Antonia M; Vieira, Verónica M; McClean, Michael D

2013-10-01

We aimed to characterize levels of polyfluorinated compounds (PFCs) in indoor dust from offices, homes, and vehicles; to investigate factors that may affect PFC levels in dust; and to examine the associations between PFCs in dust and office workers' serum. Dust samples were collected in 2009 from offices, homes, and vehicles of 31 individuals in Boston, MA and analyzed for nineteen PFCs, including perfluorooctanoate (PFOA), perfluorooctane sulfonate (PFOS), fluorotelomer alcohols (FTOHs), and sulfonamidoethanols (FOSEs). Serum was collected from each participant and analyzed for eight PFCs including PFOA and PFOS. Perfluorononanoate, PFOA, perfluoroheptanoate, perfluorohexanoate, PFOS and 8:2 FTOH had detection frequencies >50% in dust from all three microenvironments. The highest geometric mean concentration in office dust was for 8:2 FTOH (309ng/g), while PFOS was highest in homes (26.9ng/g) and vehicles (15.8ng/g). Overall, offices had the highest PFC concentrations, particularly for longer-chain carboxylic acids and FTOHs. Perfluorobutyrate was prevalent in homes and vehicles, but not offices. PFOA serum concentrations were not associated with PFC dust levels after adjusting for PFC concentrations in office air. Dust concentrations of most PFCs are higher in offices than in homes and vehicles. However, indoor dust may not be a significant source of exposure to PFCs for office workers. This finding suggests that our previously published observation of an association between FTOH concentrations in office air and PFOA concentrations in office workers was not due to confounding by PFCs in dust. © 2013.

Polyfluorinated compounds in dust from homes, offices, and vehicles as predictors of concentrations in office workers’ serum

PubMed Central

Fraser, Alicia J; Webster, Thomas F; Watkins, Deborah J; Strynar, Mark J; Kato, Kayoko; Calafat, Antonia M; Vieira, Verónica M; McClean, Michael D

2013-01-01

We aimed to characterize levels of polyfluorinated compounds (PFCs) in indoor dust from offices, homes, and vehicles; to investigate factors that may affect PFC levels in dust; and to examine the associations between PFCs in dust and office workers’ serum. Dust samples were collected in 2009 from offices, homes, and vehicles of 31 individuals in Boston, MA and analyzed for nineteen PFCs, including perfluorooctanoate (PFOA), perfluorooctane sulfonate (PFOS), fluorotelomer alcohols (FTOHs), and sulfonamidoethanols (FOSEs). Serum was collected from each participant and analyzed for eight PFCs including PFOA and PFOS. Perfluorononanoate, PFOA, perfluoroheptanoate, perfluorohexanoate, PFOS and 8:2 FTOH had detection frequencies >50% in dust from all three microenvironments. The highest geometric mean concentration in office dust was for 8:2 FTOH (309 ng/g), while PFOS was highest in homes (26.9 ng/g) and vehicles (15.8 ng/g). Overall, offices had the highest PFC concentrations, particularly for longer-chain carboxylic acids and FTOHs. Perfluorobutyrate was prevalent in homes and vehicles, but not offices. PFOA serum concentrations were not associated with PFC dust levels after adjusting for PFC concentrations in office air. Dust concentrations of most PFCs are higher in offices than in homes and vehicles. However, indoor dust may not be a significant source of exposure to PFCs for office workers. This finding suggests that our previously published observation of an association between FTOH concentrations in office air and PFOA concentrations in office workers was not due to confounding by PFCs in dust. PMID:24041736

Fate of perfluorinated carboxylates and sulfonates during snowmelt within an urban watershed.

PubMed

Meyer, Torsten; De Silva, Amila O; Spencer, Christine; Wania, Frank

2011-10-01

The transport dynamics of perfluorinated carboxylic acids and sulfonates during snowmelt in the highly urbanized Highland Creek watershed in Toronto, Canada was investigated by analyzing river water, bulk snow, and groundwater, sampled in February and March 2010, by means of liquid chromatography-tandem mass spectrometry. Perfluorohexanoate, perfluorooctanoate, and perfluorooctane sulfonate were dominant in river water, with concentrations of 4.0-14 ng·L(-1), 2.2-7.9 ng·L(-1), and 2.1-6.5 ng·L(-1), respectively. Relatively high levels of perfluorohexanoate may be related to the recent partial replacement in various consumer products of perfluorooctyl substances with shorter-chained perfluorinated compounds (PFCs). Highest PFC concentrations were found within the more urbanized part of the drainage area, suggestive of residential, industrial, and/or traffic-related sources. The riverine flux of PFCs increased during the snowmelt period, but only approximately one-fifth of the increased flux can be attributed to PFCs present in the snowpack, mostly because concentration in snow are generally quite low compared to those in river water. The remainder of the increased flux must be due to the mobilization of PFCs by the high flow conditions prevalent during snowmelt. Run-off behavior was clearly dependent on perfluoroalkyl chain length: Dilution with relatively clean snowmelt water caused a drop in the river water concentrations of short-chain PFCs at high flow during early melting. This prevented an early concentration peak of those water-soluble PFCs within the stream, as could have been expected in response to their early release from a melting snowpack. Instead, concentrations of particle-associated long-chain PFCs in creek water peaked early in the melt, presumably because high flow mobilized contaminated particles from impervious surfaces in the more urbanized areas of the watershed. The ability to enter the subsurface and deeper groundwater aquifers increased with the PFCs' water solubility, that is, was inversely related to perfluoroalkyl chain length.

Polyfluorinated and perfluorinated chemicals in precipitation and runoff from cities across eastern and central China.

PubMed

Zhao, Lijie; Zhou, Meng; Zhang, Tao; Sun, Hongwen

2013-02-01

Twenty-three polychlorinated and perfluorinated compounds (PFCs) were investigated in water phase and particulate matters of 19 precipitation samples (18 snow samples and 1 rain sample) from different cities across eastern and central China collected in February 2010. The PFCs in samples of 9e precipitation events during more than half a year at 1 site in Tianjin and 6 successive samples during 1 precipitation event were measured to elucidate the change of PFC in precipitation. In addition, PFCs in 3 runoffs at different kinds of sites in Tianjin were compared with those in the corresponding precipitation. The results showed that the particulate matters separated from the precipitation contained undetectable PFCs. The total PFC concentration ranged between 4.7 and 152 ng L(-1) in water phase of the precipitation samples, with perfluorooctanoic acid (PFOA) being detected at all of the sampling sites and the dominant PFC at most of the sampling sites. Some potential precursors of environmentally concerned PFCs and their degradation intermediates were measured simultaneously, among which 6:2 fluorotelomer unsaturated carboxylic acid (6:2 FTUCA), 8:2 FTUCA, and  × (3, 4, 5, 7):3 acid [F(CF(2))xCH(2)CH(2)COOH] were measured for the first time in Chinese precipitations; however, their concentrations were all lower than the limits of detection except that 6:2 FTUCA and 8:2 FTUCA could be detected in 3 and 8 precipitation samples, respectively. No clear seasonal variation in PFC concentrations in precipitation was observed during half a year; however, a relatively greater average concentration of total PFCs was observed during winter and summer compared with spring. The concentration of individual PFCs showed an obvious descending trend in the successive samples of the precipitation event. PFOA and perfluorononanoic acid in runoffs collected from different sites showed the following similar pattern-gas station > highway > university campus-whereas the other detected PFCs had no concurrent trend.

In vitro characterization of the immunotoxic potential of several perfluorinated compounds (PFCs).

PubMed

Corsini, Emanuela; Sangiovanni, Enrico; Avogadro, Anna; Galbiati, Valentina; Viviani, Barbara; Marinovich, Marina; Galli, Corrado L; Dell'Agli, Mario; Germolec, Dori R

2012-01-15

We have previously shown that PFOA and PFOS directly suppress cytokine secretion in immune cells, with different mechanisms of action. In particular, we have demonstrated a role for PPAR-α in PFOA-induced immunotoxicity, and that PFOS has an inhibitory effect on LPS-induced I-κB degradation. These studies investigate the immunomodulatory effects of four other PFCs, namely PFBS, PFOSA, PFDA, and fluorotelomer using in vitro assays. The release of the pro-inflammatory cytokines IL-6 and TNF-α was evaluated in lipolysaccharide (LPS)-stimulated human peripheral blood leukocytes (hPBL) and in the human promyelocytic cell line THP-1, while the release of IL-10 and IFN-γ was evaluated in phytohemagglutinin (PHA)-stimulated hPBL. All PFCs suppressed LPS-induced TNF-α production in hPBL and THP-1 cells, while IL-6 production was suppressed by PFOSA, PFOS, PFDA and fluorotelomer. PFBS, PFOSA, PFOS, PFDA and fluorotelomer inhibited PHA-induced IL-10 release, while IFN-γ secretion was affected by PFOSA, PFOS, PFDA and fluorotelomer. Leukocytes obtained from female donors appear to be more sensitive to the in vitro immunotoxic effects of PFCs when their responses are compared to the results obtained using leukocytes from male donors. Mechanistic investigations demonstrated that inhibition of TNF-α release in THP-1 cells occurred at the transcriptional level. All PFCs, including PFOA and PFOS, decreased LPS-induced NF-κB activation. With the exception of PFOA, none of the PFCs tested was able to activate PPARα driven transcription in transiently transfected THP-1 cells, excluding a role for PPARα in the immunomodulation observed. PFBS and PFDA prevented LPS-induced I-κB degradation. Overall, these studies suggest that PFCs affect NF-κB activation, which directly suppresses cytokine secretion by immune cells. Our results indicate that PFOA is the least active of the PFCs examined followed by PFBS, PFDA, PFOS, PFOSA and fluorotelomer. Copyright © 2011 Elsevier Inc. All rights reserved.

Li experiments at the tokamak T-11 M in field of steady state PFC investigations

NASA Astrophysics Data System (ADS)

Mirnov, S. V.; Lazarev, V. B.

2011-08-01

The renewable plasma facing components (PFCs) of steady state tokamak-reactor can be created in framework of Lithium emitter-collector concept, which suggests Li-loop development close the Li-PFC and plasma periphery. It should ensure: Li-emission from PFC into the plasma, plasma periphery cooling by non-coronal Li radiation, Li ions collection before their loss on the wall and Li return into emitter. The subjects of the last T-11 M investigations were the Lithium collection by limiters and Lithium removal from the wall during tokamak conditioning. The Lithium behavior was studied with witness samples and mobile graphite probe. It was shown that Li-deposit on the sides of rail Li-limiter (collector) is proportional to the Li-emission from the Li-limiter (emitter). Lithium deposit on the ion-drift side of Li-limiter is up to 2-3 times more than on the electron-side. The efficiency of Li-collection by T-11 M limiters can be 60 ± 20% of total Lithium emission from Li-limiter during plasma discharges.

Elemental and topographical imaging of microscopic variations in deposition on NSTX-U and DIII-D samples

NASA Astrophysics Data System (ADS)

Skinner, C. H.; Kaita, R.; Koel, B. E.; Chrobak, C. P.; Wampler, W. R.

2017-10-01

Tokamak plasma facing components (PFCs) have surface roughness that can cause microscopic spatial variations in erosion and deposition and hence influence material migration. Previous RBS measurements showed indirect evidence for this but the spatial (0.5mm) resolution was insufficient for direct imaging. We will present elemental images at sub-micron resolution of deposition on NSTX-U and DiMES samples that show strong microscopic variations and correlate this with 3D topographical maps of surface irregularities. The elemental imaging is performed with a Scanning Auger Microprobe (SAM) that measures element-specific Auger electrons excited by an SEM electron beam. 3D topographical maps of the samples are performed with a Leica DCM 3D confocal light microscope and compared to the elemental deposition pattern. The initial results appear consistent with erosion at the downstream edges of the surface pores exposed to the incident ion flux, whereas the deeper regions are shadowed and serve as deposition traps. Support was provided through DOE Contract Numbers DE-AC02-09CH11466, DE-FC02-04ER54698 and DE-NA0003525.

Lithium-Metal Infused Trenches: Progress toward a Divertor Solution

NASA Astrophysics Data System (ADS)

Ruzic, D. N.; Fiflis, P.; Christenson, M.; Szott, M.; Xu, W.; Jung, S.; Morgan, T. W.; Kalathiparambil, K.

2014-10-01

The application of liquid metal, especially liquid lithium, as a plasma facing component (PFC) has the capacity to offer a strong alternative to solid PFCs by reducing damage concerns and enhancing plasma performance. The Liquid-Metal Infused Trenches (LiMIT) concept is a liquid metal divertor alternative which employs thermoelectric current from either plasma or external heating in tandem with the toroidal field to self-propel liquid lithium through a series of trenches. LiMIT has been tested in several devices, namely HT-7, the UIUC SLiDE and TELS facilities and Magnum PSI at heat fluxes of up to 3 MW/m-2. Results of these experiments, including velocity and temperature measurements, power handling considerations, and preliminary vapor shielding results will be discussed, focusing on the 117 shots performed at Magnum scanning magnetic fields and heat fluxes up to ~ 0.3 T and 3 MW/m-2. Concerns over tritium retention and MHD droplet ejection will additionally be addressed. LiMIT has also been proposed to function as a limiter on the EAST moveable limiter arm and tests have been performed with a prototype module inclined at various angles.

Per- and polyfluorinated compounds (PFCs) in house dust and indoor air in Catalonia, Spain: implications for human exposure.

PubMed

Ericson Jogsten, I; Nadal, M; van Bavel, B; Lindström, G; Domingo, J L

2012-02-01

A total of 27 per- and polyfluorinated compounds (PFCs) were determined in both house dust (n=10) and indoor air (n=10) from selected homes in Catalonia, Spain. Concentrations were found to be similar or lower than those previously reported for household microenvironments in other countries. Ten PFCs were detected in all house dust samples. The highest mean concentrations corresponded to perfluorodecanoic acid (PFDA) and perfluorononanoic acid (PFNA), 10.7 ng/g (median: 1.5 ng/g) and 10.4 ng/g (median: 5.4 ng/g), respectively, while the 8:2 fluorotelomer alcohol (FTOH) was the dominating neutral PFC at a concentration of 0.41 ng/g (median: 0.35 ng/g). The indoor air was dominated by the FTOHs, especially the 8:2 FTOH at a mean (median) concentration of 51 pg/m(3) (median: 42 pg/m(3)). A limited number of ionic PFCs were also detected in the indoor air samples. Daily intakes of PFCs were estimated for average and worst case scenarios of human exposure from indoor sources. For toddlers, this resulted in average intakes of ∑ionic PFCs of 4.9ng/day (0.33 ng/kg(bw)/day for a 15 kg toddlers) and ∑neutral PFCs of 0.072 ng/day (0.005 ng/kg(bw)/day) from house dust. For adults, the average daily intakes of dust were 3.6 and 0.053 ng/day (0.05 and 0.001 ng/kg(bw)/day for a 70 kg adult) for ∑ionic and ∑neutral PFCs, respectively. The average daily inhalation of ∑neutral PFCs was estimated to be 0.9 and 1.3 ng/day (0.06 and 0.02 ng/kg(bw)/day) for toddlers and adults, respectively. For PFOS, the main ionic PFC detected in indoor air samples, the median intakes (based on those samples where PFOS was detected), resulted in indoor exposures of 0.06 and 0.11 ng/day (0.004 and 0.002 ng/kg(bw)/day) for toddlers and adults, respectively. Based on previous studies on dietary intake and drinking water consumption, both house dust and indoor air contribute significantly less to PFC exposure within this population. Copyright © 2011 Elsevier Ltd. All rights reserved.

Occurrence of perfluorinated compounds in raw water from New Jersey public drinking water systems.

PubMed

Post, Gloria B; Louis, Judith B; Lippincott, R Lee; Procopio, Nicholas A

2013-01-01

Perfluorooctanoic acid (PFOA) and perfluorooctane sulfonic acid (PFOS) were previously detected (≥ 4 ng/L) in 65% and 30%, respectively, of 23 New Jersey (NJ) public drinking water systems (PWS) sampled in 2006. We now report on a 2009 study of the occurrence of PFOA, PFOS, and eight other perfluorinated compounds (PFCs) in raw water samples from 30 intakes (18 groundwater and 12 surface water) from 29 additional NJ PWS. Between 1 and 8 PFCs were detected (≥ 5 ng/L) in 21 (70%) of 30 PWS samples at total PFC concentrations of 5-174 ng/L. Although PFOA was the most commonly detected PFC (57% of samples) and was found at the highest maximum concentration (100 ng/L), some of the higher levels of other PFCs were at sites with little or no PFOA. Perfluorononanoic acid was detected more frequently (30%) and at higher concentrations (up to 96 ng/L) than in raw or finished drinking water elsewhere, and it was found at several sites as the sole or predominant PFC, a pattern not reported in other drinking water studies. PFOS, perfluoropentanoic acid, and perfluorohexanoic acid were each detected in more than 20% of samples, while perfluoroheptanoic acid, perfluorobutane sulfonic acid, and perfluorohexane sulfonic acid were detected less frequently. Perfluorobutanoic acid was found only once (6 ng/L), and perfluorodecanoic acid was not detected. Total PFCs were highest in two reservoirs near an airfield; these were also the only sites with total perfluorosulfonic acids higher than total perfluorocarboxylic acids (PFCAs). PFC levels in raw and finished water from the same source were similar at those sites where both were tested. Five wells of two additional NJ PWS known to be contaminated with PFOA were also each sampled 4-9 times in 2010-13 for nine of the same PFCs. Total PFCs (almost completely PFCAs) at one of these PWS located near an industrial source of PFCs were higher than in any other PWS tested (up to 330 ng/L). These results show that multiple PFCs are commonly found in raw water from NJ PWS. Future work is needed to develop approaches for assessing the potential human health risks of exposure to mixtures of PFCs found in drinking water and other environmental media.

Perfluorinated compounds in fish from U.S. urban rivers and the Great Lakes.

PubMed

Stahl, Leanne L; Snyder, Blaine D; Olsen, Anthony R; Kincaid, Thomas M; Wathen, John B; McCarty, Harry B

2014-11-15

Perfluorinated compounds (PFCs) have recently received scientific and regulatory attention due to their broad environmental distribution, persistence, bioaccumulative potential, and toxicity. Studies suggest that fish consumption may be a source of human exposure to perfluorooctane sulfonate (PFOS) or long-chain perfluorocarboxylic acids. Most PFC fish tissue literature focuses on marine fish and waters outside of the United States (U.S.). To broaden assessments in U.S. fish, a characterization of PFCs in freshwater fish was initiated on a national scale using an unequal probability design during the U.S. Environmental Protection Agency's (EPA's) 2008-2009 National Rivers and Streams Assessment (NRSA) and the Great Lakes Human Health Fish Tissue Study component of the 2010 EPA National Coastal Condition Assessment (NCCA/GL). Fish were collected from randomly selected locations--164 urban river sites and 157 nearshore Great Lake sites. The probability design allowed extrapolation to the sampled population of 17,059 km in urban rivers and a nearshore area of 11,091 km(2) in the Great Lakes. Fillets were analyzed for 13 PFCs using high-performance liquid chromatography tandem mass spectrometry. Results showed that PFOS dominated in frequency of occurrence, followed by three other longer-chain PFCs (perfluorodecanoic acid, perfluoroundecanoic acid, and perfluorododecanoic acid). Maximum PFOS concentrations were 127 and 80 ng/g in urban river samples and Great Lakes samples, respectively. The range of NRSA PFOS detections was similar to literature accounts from targeted riverine fish sampling. NCCA/GL PFOS levels were lower than those reported by other Great Lakes researchers, but generally higher than values in targeted inland lake studies. The probability design allowed development of cumulative distribution functions (CDFs) to quantify PFOS concentrations versus the sampled population, and the application of fish consumption advisory guidance to the CDFs resulted in an estimation of the proportion of urban rivers and the Great Lakes that exceed human health protection thresholds. Copyright © 2014. Published by Elsevier B.V.

Reversible and irreversible sorption of perfluorinated compounds (PFCs) by sediments of an urban reservoir.

PubMed

Chen, Huiting; Reinhard, Martin; Nguyen, Viet Tung; Gin, Karina Yew-Hoong

2016-02-01

Uncertainty about the extent to which contaminant sorption by suspended solids and bed sediments is irreversible is a major impediment for modeling and managing the water quality of surface water resources. This study examined reversible and irreversible sorption of several perfluorinated compounds (PFCs) to bed sediments from an urban reservoir. PFCs investigated include C4, C6, C8, C9 and C10 perfluoroalkanoate homologues (PFBA, PFHxA, PFOA, PFNA and PFDA, respectively) and perfluorooctane and hexane sulfonate (PFOS and PFHxS, respectively). Although sorption branches of the PFOS, PFNA and PFDA isotherms were nearly linear (implying a partitioning-like process), desorption experiments indicated that a fraction of the sorbed PFCs were entrapped and resistant to desorption. The hysteretic desorption branches were approximately linear. Irreversibility increased with chain length and was nearly complete for PFDA (thermodynamic irreversibility index (TII) 0.98). For the weakly sorbing PFOA and PFHxS, sorption was largely reversible. Data suggest that (1) for the strongly sorbing PFCs, e.g. PFNA, PFDA and PFOS, bed sediments acted predominantly as irreversible sinks, (2) aqueous concentrations of the moderately sorbing PFCs (PFOA and PFHxS) are buffered by reversibly sorbing suspended solids, and (3) the short-chain PFCs (PFBA and PFHxA) are not significantly sorbed and therefore not expected to be significantly influenced by sediment transport. Situations in which highly contaminated particles entering relatively clean water bodies, equilibrium is approached from the reverse (desorption) direction. For irreversibly sorbed contaminants field-based K(D) values will be higher than the K(D) values derived from laboratory sorption data obtained from forward sorption experiments. Copyright © 2015 Elsevier Ltd. All rights reserved.

Occurrence of perfluoroalkyl compounds in surface waters from the North Pacific to the Arctic Ocean.

PubMed

Cai, Minghong; Zhao, Zhen; Yin, Zhigao; Ahrens, Lutz; Huang, Peng; Cai, Minggang; Yang, Haizhen; He, Jianfeng; Sturm, Renate; Ebinghaus, Ralf; Xie, Zhiyong

2012-01-17

Perfluoroalkyl compounds (PFCs) were determined in 22 surface water samples (39-76°N) and three sea ice core and snow samples (77-87°N) collected from North Pacific to the Arctic Ocean during the fourth Chinese Arctic Expedition in 2010. Geographically, the average concentration of ∑PFC in surface water samples were 560 ± 170 pg L(-1) for the Northwest Pacific Ocean, 500 ± 170 pg L(-1) for the Arctic Ocean, and 340 ± 130 pg L(-1) for the Bering Sea, respectively. The perfluoroalkyl carboxylates (PFCAs) were the dominant PFC class in the water samples, however, the spatial pattern of PFCs varied. The C(5), C(7) and C(8) PFCAs (i.e., perfluoropentanoate (PFPA), perfluoroheptanoate (PFHpA), and perfluorooctanoate (PFOA)) were the dominant PFCs in the Northwest Pacific Ocean while in the Bering Sea the PFPA dominated. The changing in the pattern and concentrations in Pacific Ocean indicate that the PFCs in surface water were influenced by sources from the East-Asian (such as Japan and China) and North American coast, and dilution effect during their transport to the Arctic. The presence of PFCs in the snow and ice core samples indicates an atmospheric deposition of PFCs in the Arctic. The elevated PFC concentration in the Arctic Ocean shows that the ice melting had an impact on the PFC levels and distribution. In addition, the C(4) and C(5) PFCAs (i.e., perfluorobutanoate (PFBA), PFPA) became the dominant PFCs in the Arctic Ocean indicating that PFBA is a marker for sea ice melting as the source of exposure.

Different binding mechanisms of neutral and anionic poly-/perfluorinated chemicals to human transthyretin revealed by In silico models.

PubMed

Yang, Xianhai; Lyakurwa, Felichesmi; Xie, Hongbin; Chen, Jingwen; Li, Xuehua; Qiao, Xianliang; Cai, Xiyun

2017-09-01

Chemical forms-dependent binding interactions between phenolic compounds and human transthyretin (hTTR) have been elaborated previously. However, it is not known whether the binding interactions between ionizable halogenated alphatic compounds and hTTR also have the same manner. In this study, poly-/perfluorinated chemicals (PFCs) were selected as model compounds and molecular dynamic simulation was performed to investigate the binding mechanisms between PFCs and hTTR. Results show the binding interactions between the halogenated aliphatic compounds and hTTR are related to the chemical forms. The ionized groups of PFCs can form electrostatic interactions with the -NH + 3 groups of Lys 15 residues in hTTR and form hydrogen bonds with the residues of hTTR. By analyzing the molecular orbital energies of PFCs, we also found that the anionic groups (nucleophile) in PFCs could form electron donor - acceptor interactions with the -NH + 3 groups (electrophile) in Lys 15. The aforementioned orientational interactions make the ionized groups of the PFCs point toward the entry port of the binding site. The roles of fluorine atoms in the binding interactions were also explored. The fluorine atoms can influence the binding interactions via inductive effects. Appropriate molecular descriptors were selected to characterize these interactions, and two quantitative structure-activity relationship models were developed. Copyright © 2017 Elsevier Ltd. All rights reserved.

Polyfluoroalkyl Chemicals in the Serum and Milk of ...

EPA Pesticide Factsheets

Polyfluoroalkyl chemicals (PFCs) comprise a group of man-made organic compounds, some of which are persistent contaminants with developmental toxicity shown in laboratory animals. There is a paucity of human perinatal exposure data. The US EPA conducted a pilot study (Methods Advancement in Milk Analysis) including 34 breastfeeding women in North Carolina. Milk and serum samples were collected at 2-7 weeks and 3-4 months postpartum; 9 PFCs were assessed in milk and 7 in serum. Perfluorooctane sulfonic acid (PFOS), perfluorooctanoic acid (PFOA), perfluorononanoic acid (PFNA), and perfluorohexane sulfonic acid (PFHxS) were found in nearly 100% of the serum samples. PFOS and PFOA were found at the highest concentrations. PFCs were below the limit of detection in most milk samples. Serum concentrations of PFOS, PFOA and PFHxS were lower (p<0.01) at the second visit compared to the first visit, and living in North Carolina 10 years or longer was related to elevated PFOS, PFOA and PFNA (p<0.03). These pilot data support the need to further explore perinatal PFC exposures and potentially related health effects, as planned in the upcoming National Children’s Study which provided the framework for this investigation. These data demonstrate very low transfer of perfluorinated chemicals (PFCs) to breast milk, even though PFCs are readily detected in the sera of lactating NC women. Our data correlation statistics suggest that there is an elevation of average serum PFCs i

Bioaccumulation of perfluorochemicals in Pacific oyster under different salinity gradients.

PubMed

Jeon, Junho; Kannan, Kurunthachalam; Lim, Han Kyu; Moon, Hyo Bang; Ra, Jin Sung; Kim, Sang Don

2010-04-01

Despite the reports of widespread occurrence of perfluorinated compounds (PFCs) in estuarine and coastal waters and open seas, little is known on the effect of salinity on bioaccumulation. In this study, effects of salinity on bioaccumulation of PFCs in Pacific oysters (Crassostrea gigas) were investigated. Furthermore, partitioning of PFCs between water and particles (oysters' food) was examined at different salinities. The distribution coefficients (K(d); partitioning between water and particles) for selected PFCs, that is, PFOS, PFOA, PFDA, and PFUnDA, increased by 2.1- to 2.7-fold with the increase in water salinity from 10 to 34 psu, suggesting "salting-out" effect, and the salting constant (delta) was estimated to range from 0.80 to 1.11. The nonlinear regression analysis of bioaccumulation suggested increase in aqueous and dietary uptake rates (K(w) and K(f)), with the increase in salinity, which resulted in elevated bioaccumulation, although the depuration rates (K(e)) also increased. The relative abundance of long carbon chain length PFCs (i.e., PFDA and PFUnDA) increased as salinity increased, while the proportion of PFOS and PFOA decreased, which is explained by the positive relationship between delta and carbon chain length. The contribution of diet to bioaccumulation in oysters ranged from 18 to 92%. Overall, salinity not only affected the chemistry of PFCs, but also the physiology of oysters, contributing to sorption and bioaccumulation of perfluorochemicals in oysters.

Distribution of perfluorooctane sulfonate and other perfluorochemicals in the ambient environment around a manufacturing facility in China.

PubMed

Wang, Yawei; Fu, Jianjie; Wang, Thanh; Liang, Yong; Pan, Yuanyuan; Cai, Yaqi; Jiang, Guibin

2010-11-01

Perfluorinated compounds (PFCs) can be released to the surrounding environment during manufacturing and usage of PFC containing products, which are considered as main direct sources of PFCs in the environment. This study evaluates the release of perfluorooctane sulfonate (PFOS) and other PFCs to the ambient environment around a manufacturing plant. Among the nine PFCs analyzed, only PFOS, perfluorooctanoic acid (PFOA), and perfluorohexane sulfonate (PFHxS) were found in dust, water, soil, and chicken eggs. Very high concentrations of PFOS and PFOA were found in dust from the production storage, raw material stock room, and sulfonation workshop in the manufacturing facility, with the highest value at 4962 μg/g (dry weight) for PFOS and 160 μg/g for PFOA. A decreasing trend of the three PFCs concentrations in soils, water, and chicken eggs with increasing distance from the plant was found, indicating the production site to be the primary source of PFCs in this region. Risk quotients (RQs) assessment for surface water >500 m away from the plant were less than unity. Risk assessment of PFOS using predicted no-effect concentration (PNEC, 3.23 ng/g on a logarithmic scale) indicated no immediate ecological risk of a reduction in offspring survival. PFOS concentrations in most egg samples did not exceed the benchmark concentration derived in setting a reference dose for noncancer health effects (0.025 μg/(kgxd)).

Recent developments in polyfluoroalkyl compounds research: a focus on human/environmental health impact, suggested substitutes and removal strategies.

PubMed

Mudumbi, John Baptist Nzukizi; Ntwampe, Seteno Karabo Obed; Matsha, Tandi; Mekuto, Lukhanyo; Itoba-Tombo, Elie Fereche

2017-08-01

Between the late 1940s and early 1950s, humans manufactured polyfluoroalkyl compounds (PFCs) using electrochemical fluorination and telomerisation technologies, whereby hydrogen atoms are substituted by fluorine atoms, thus conferring unnatural and unique physicochemical properties to these compounds. Presently, there are wide ranges of PFCs, and owing to their bioaccumulative properties, they have been detected in various environmental matrices and in human sera. It has thus been suggested that they are hazardous. Hence, this review aims at highlighting the recent development in PFC research, with a particular focus on perfluorooctanoate (PFOA) and perfluorooctane sulfonate (PFOS), the most studied and predominantly found PFCs in various environmental matrices, although recent reports have included perfluorobutane sulfonate (PFBS), which was previously regarded as innocuously harmless, when compared to its counterparts, PFOA and PFOS. As such, proper investigations are thus required for a better understanding of short-chain PFC substitutes, which have been suggested as suitable replacements to long-chained PFCs, although these substitutes have also been suggested to pose various health risks comparable to those associated with long-chain PFCs. Similarly, several novel technologies, such as PFC reduction using zero-valent iron, including removal at point of use, adsorption and coagulation, have been proposed. However, regardless of how efficient removers some of these techniques have proven to be, short-chain PFCs remain a challenge to overcome for scientists, in this regard.

Assessment of perfluorinated compounds (PFCs) in plasma of bottlenose dolphins from two southeast US estuarine areas: relationship with age, sex and geographic locations.

PubMed

Fair, Patricia A; Houde, Magali; Hulsey, Thomas C; Bossart, Gregory D; Adams, Jeff; Balthis, Len; Muir, Derek C G

2012-01-01

Plasma PFCs were measured in 157 bottlenose dolphins (Tursiops truncatus) sampled from two US southeast Atlantic sites (Charleston (CHS), SC and Indian River Lagoon (IRL), FL) during 2003-2005. ∑PFCs, perfluoroalkyl carboxylates (∑PFCAs), perfluoroalkyl sulfonates (∑PFSAs) and individual compounds were significantly higher in CHS dolphins for all age/sex categories compared to IRL dolphins. Highest ∑PFCs concentrations occurred in CHS juvenile dolphins (2340 ng/g w.w.); significantly higher than found in adults (1570 ng/g w.w. males; 1330 ng/g w.w. females). ∑PFCAs were much greater in CHS dolphins (≈ 21%) compared to IRL dolphins (≈ 7%); ∑PFSAs were 79% in CHS dolphins versus 93% in IRL dolphins. PFOS, the dominant compound, averaged 72% and 84%, respectively, in CHS and IRL dolphins. Decreasing PFC levels occurred with age on the bioaccumulation of PFCs in both sites. These observations suggest PFC accumulation in these two dolphin populations are influenced by site-specific exposures with significantly higher levels in CHS dolphins. Published by Elsevier Ltd.

The role of endoscopic intervention in the management of inflammatory pancreatic fluid collections.

PubMed

Parihar, Vikrant; Ridgway, Paul F; Conlon, Kevin C; Huggett, Matthew; Ryan, Barbara M

2017-04-01

Pancreatic fluid collections (PFCs) are a frequent complication of pancreatitis, or less commonly, pancreatic trauma or surgery. The revised Atlanta Classification categorizes PFCs as acute or chronic, with further subclassification of acute collections into acute peripancreatic collections and acute necrotic collections and of chronic fluid collections into pseudocysts and walled-off pancreatic necrosis. Acute PFCs are generally only subjected to an intervention when they are infected and not responding to antibiotics and are not managed endoscopically. Chronic PFCs, both pseudocysts and walled-off pancreatic necrosis, require intervention only when symptomatic or enlarging over time. Endoscopic ultrasound-guided drainage has become the mainstay of management for chronic PFCs that require intervention. Developments in medical devices over the past few years have significantly simplified and shortened the duration of the procedure itself, but the optimum choice of stent in different clinical scenarios remains to be defined, as does the place of endoscopic necrosectomy. To optimize outcomes, these patients should undergo a careful preprocedure workup and discussion in a multidisciplinary environment and procedures should be carried out in high-volume pancreatic units.

Endoscopic ultrasound guided drainage of pancreatic fluid collections: Assessment of the procedure, technical details and review of the literature

PubMed Central

Puri, Rajesh; Thandassery, Ragesh Babu; Alfadda, Abdulrahman A; Kaabi, Saad Al

2015-01-01

Endoscopic ultrasound (EUS) guided drainage of pancreatic fluid collections (PFC) has become increasingly popular and become first line management option in many centers. Use of therapeutic echoendoscopes has greatly increased the applicability of EUS guided transmural drainage. Drainage is indicated in symptomatic PFCs, PFC related infection, bleed, luminal obstruction, fistulization and biliary obstruction. EUS guided transmural drainage of PFCs is preferred in patients with non bulging lesions, portal hypertension, bleeding tendency and in those whom conventional drainage has failed. In the present decade significant progress has been made in minimally invasive endoscopic techniques. There are newer stent designs, access devices and techniques for more efficient drainage of PFCs. In this review, we discuss the EUS guided drainage of PFCs in acute pancreatitis. PMID:25901214

Biomonitoring perfluorinated compounds in Catalonia, Spain: concentrations and trends in human liver and milk samples.

PubMed

Kärrman, Anna; Domingo, José L; Llebaria, Xavier; Nadal, Martí; Bigas, Esther; van Bavel, Bert; Lindström, Gunilla

2010-03-01

Perfluorinated compounds (PFCs) are global environmental pollutants that bioaccumulate in wildlife and humans. Laboratory experiments have revealed toxic effects such as delayed development, humoral suppression, and hepatotoxicity. Although numerous human blood levels have been reported, little is known about distribution in the human body. Knowledge about PFC distribution and accumulation in the human body is crucial to understanding uptake and subsequent effects as well as to conduct risk assessments. The present study reports PFC levels in human liver and breast milk from a general population living in Catalonia, Spain. Liver and milk levels are compared to previously reported levels in blood from the same geographic area as well as to other existing reports on human liver and milk levels in other countries. Human liver (n = 12) and milk (n = 10) samples were collected in 2007 and 2008 in Catalonia, Spain. Liver samples were taken postmortem from six males and six females aged 27-79 years. Milk samples were from healthy primipara women (30-39 years old). Both liver and milk were analyzed by solid-phase extraction and ultra-performance liquid chromatography tandem mass spectrometry. Six PFCs were detected in liver, with perfluorooctanesulfonate (PFOS, 26.6 ng/g wet weight) being the chemical with the highest mean concentration. Other PFCs such as perfluorohexanesulfonate (PFHxS), perfluorooctanoic acid (PFOA), and acids with chain lengths up to C11 were also detected, with mean levels ranging between 0.50 and 1.45 ng/g wet weight. On the other hand, PFOS and PFHxS were the only PFCs detected in human milk, with mean concentrations of 0.12 and 0.04 ng/mL, respectively. While milk concentrations were similar to reported levels from other countries, liver samples contained more PFCs above quantification limits and higher PFOS concentrations compared to the only two other reports found in the literature. Differences between the results of the present study and those concerning previous investigations can be due to declining levels of some PFCs, which have been reported for the USA. The relationship between PFC concentrations in human liver, milk, and blood was assessed using blood concentrations previously determined in Catalonia. Those levels resulted in liver/serum ratios of 1.7:1, 1.4:1, and 2.1:1 for PFOS, perfluorodecanoic acid, and perfluoroundecanoic acid, respectively. Accumulation in liver is suggested for PFOS and the perfluorocarboxylic acids with carbon chain lengths C9, C10, and C11. For PFOA and PFHxS, fivefold and 14-fold higher concentrations, respectively, were seen in serum as compared to liver. The mean concentration of PFOS and PFHxS in milk was only 0.8% and 0.6% of the reported mean serum level, respectively. The results of the present study show that several PFCs could be detected in human liver samples of subjects living in Tarragona. Concerning human milk, the mechanism by which PFCs are transferred from mother's blood to breast milk is still unclear. Considering that PFCs are strongly bound to the protein fraction in blood, the possibility of PFCs entering the milk and accumulating to levels observed in maternal plasma is limited. Interestingly, the potential accumulation difference for PFCs with different chain lengths might be of great importance for risk assessment. Continuing studies on the distribution of different PFCs in human tissue are therefore justified.

The DoD Environmental Restoration Program: An Air Force Perspective and Status Update

DTIC Science & Technology

2011-11-01

PFCs of interest Perfluorooctane sulfonate ( PFOS ) Perfluorooctanoic acid ( PFOA ) C8HF17O3S C8HF15O2 I n t e g r i t y - S...Mixtures Change in science/methods Evaluation in progress Perchlorate Lower regulatory standards Continue to monitor PFCs ( PFOS / PFOA ) Regulatory interest...e 25 DoD Activities: PFCs PFOA / PFOS on the DoD Emerging Contaminant Watch List for continued surveillance of regulatory actions SERDP

Edge transport and turbulence reduction, and formation of ultra-wide pedestals with lithium coated PFCs in NSTX

NASA Astrophysics Data System (ADS)

Canik, John

2010-11-01

The coating of plasma facing components (PFCs) with lithium improves energy confinement [1] and eliminates ELMs in the National Spherical Torus Experiment (NSTX), the latter due to a relaxation of the density and pressure profiles that reduces the drive for peeling-ballooning modes [2]. Here we show that both a reduction in recycling (due to lithium pumping) and cross-field transport is needed to reproduce the measured profile changes. Furthermore we document a concomitant density fluctuation reduction measured in the steep gradient region. The experimental transport coefficients are obtained via data-constrained modeling using the SOLPS code [3], which couples a 2D fluid treatment of the edge plasma transport to a Monte Carlo neutrals calculation. First, a reduction in the PFC recycling coefficient from R˜0.98 to R˜0.90 is required to match the drop in Dα emission with lithium coatings. Furthermore, a ˜75% drop of the D and χe from 0.8 < ψN < 0.93 are needed to match the profile relaxation with lithium coatings; indeed, the region of low transport in the H-mode simply extends to the innermost domain of the simulation. Transport is similar with and without lithium coatings outside of ψN ˜ 0.93, with D/χe ˜ 0.2/1.0 m2/s. Turbulence measurements using an edge reflectometry system [4] show a decrease in broadband density fluctuations with lithium coatings, primarily at frequencies <10 kHz. These transport changes allow the realization of very wide pedestals, with a ˜100% width increase relative to the reference discharges. [4pt] [1] H. W. Kugel et al, Phys. Plas. 15 (2008) 056118. [0pt] [2] R. Maingi et al, Phys. Rev. Lett. 103 (2009) 075001. [0pt] [3] R. Schneider et al, Contr. Plas. Phys. 46 (2006) 3. [0pt] [4] S Kubota et al, Bull. Am. Phys. Soc. 53 (2008) 188.

Advanced divertor configurations with large flux expansion

NASA Astrophysics Data System (ADS)

Soukhanovskii, V. A.; Bell, R. E.; Diallo, A.; Gerhardt, S.; Kaye, S.; Kolemen, E.; LeBlanc, B. P.; McLean, A.; Menard, J. E.; Paul, S. F.; Podesta, M.; Raman, R.; Ryutov, D. D.; Scotti, F.; Kaita, R.; Maingi, R.; Mueller, D. M.; Roquemore, A. L.; Reimerdes, H.; Canal, G. P.; Labit, B.; Vijvers, W.; Coda, S.; Duval, B. P.; Morgan, T.; Zielinski, J.; De Temmerman, G.; Tal, B.

2013-07-01

Experimental studies of the novel snowflake divertor concept (D. Ryutov, Phys. Plasmas 14 (2007) 064502) performed in the NSTX and TCV tokamaks are reviewed in this paper. The snowflake divertor enables power sharing between divertor strike points, as well as the divertor plasma-wetted area, effective connection length and divertor volumetric power loss to increase beyond those in the standard divertor, potentially reducing heat flux and plasma temperature at the target. It also enables higher magnetic shear inside the separatrix, potentially affecting pedestal MHD stability. Experimental results from NSTX and TCV confirm the predicted properties of the snowflake divertor. In the NSTX, a large spherical tokamak with a compact divertor and lithium-coated graphite plasma-facing components (PFCs), the snowflake divertor operation led to reduced core and pedestal impurity concentration, as well as re-appearance of Type I ELMs that were suppressed in standard divertor H-mode discharges. In the divertor, an otherwise inaccessible partial detachment of the outer strike point with an up to 50% increase in divertor radiation and a peak divertor heat flux reduction from 3-7 MW/m2 to 0.5-1 MW/m2 was achieved. Impulsive heat fluxes due to Type-I ELMs were significantly dissipated in the high magnetic flux expansion region. In the TCV, a medium-size tokamak with graphite PFCs, several advantageous snowflake divertor features (cf. the standard divertor) have been demonstrated: an unchanged L-H power threshold, enhanced stability of the peeling-ballooning modes in the pedestal region (and generally an extended second stability region), as well as an H-mode pedestal regime with reduced (×2-3) Type I ELM frequency and slightly increased (20-30%) normalized ELM energy, resulting in a favorable average energy loss comparison to the standard divertor. In the divertor, ELM power partitioning between snowflake divertor strike points was demonstrated. The NSTX and TCV experiments are providing support for the snowflake divertor as a viable solution for the outstanding tokamak plasma-material interface issues.

Fabrication, characterization, and modeling of piezoelectric fiber composites

NASA Astrophysics Data System (ADS)

Lin, Xiujuan; Zhou, Kechao; Button, Tim W.; Zhang, Dou

2013-07-01

Piezoelectric fiber composites (PFCs) with interdigitated electrodes have attracted increasing interest in a variety of industrial, commercial, and aerospace markets due to their unique flexibility, adaptability, and improved transverse actuation performance. Viscous plastic processing technique was utilized for the fabrication of PFCs with customized feature sizes. The assembly parameters showed great influence on the performance of PFCs, which was verified by the finite element analysis. The cracks were identified in the fibers underneath the electrode finger after several millions cycles due to the stress and electric field concentration. The electrode finger width was an important structural parameter and showed great influence on the actuation performance and the stress distribution in the PFCs. The finite element analysis revealed that wider electrode finger would be beneficial for reducing the risk of materials failure with slight influence on the actuation performance.

Encoding of Reward and Space During a Working Memory Task in the Orbitofrontal Cortex and Anterior Cingulate Sulcus

PubMed Central

Kennerley, Steven W.

2009-01-01

Several lines of research indicate that emotional and motivational information may be useful in guiding the allocation of attentional resources. Two areas of the frontal lobe that are particularly implicated in the encoding of motivational information are the orbital prefrontal cortex (PFo) and the dorsomedial region of prefrontal cortex, specifically the anterior cingulate sulcus (PFcs). However, it remains unclear whether these areas use this information to influence spatial attention. We used single-unit neurophysiology to examine whether, at the level of individual neurons, there was evidence for integration between reward information and spatial attention. We trained two subjects to perform a task that required them to attend to a spatial location across a delay under different expectancies of reward for correct performance. We balanced the order of presentation of spatial and reward information so we could assess the neuronal encoding of the two pieces of information independently and conjointly. We found little evidence for encoding of the spatial location in either PFo or PFcs. In contrast, both areas encoded the expected reward. Furthermore, PFo consistently encoded reward more quickly than PFcs, although reward encoding was subsequently more prevalent and stronger in PFcs. These results suggest a differential contribution of PFo and PFcs to reward encoding, with PFo potentially more important for initially determining the value of rewards predicted by sensory stimuli. They also suggest that neither PFo nor PFcs play a direct role in the control of spatial attention. PMID:19776363

Perfluorocarbons and Gilbert syndrome (phenotype) in the C8 Health Study Population

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fan, Hongmin; Department of Epidemiology and Statistics, School of Public Health, Hebei United University, Hebei 063000; Ducatman, Alan

Background: Gilbert syndrome (GS) is an inherited defect of bilirubin conjugation, most commonly caused by a gene mutation for the enzyme UGT1A. GS is known to affect the metabolism and excretion of drugs and xenobiotics. Perfluorocarbon compounds (PFCs) are bio-persistent environmental contaminants that affect metabolic regulation. In this study, we examined the associations of GS phenotype and serum PFCs in the C8 Health Study Population. Materials and methods: Using 2005–2006 data from a large PFC-exposure population survey, we compared serum PFCs concentrations between GS and non GS clinical phenotypes, in a cross sectional design, adjusting for standard risk factors, includingmore » age, BMI, smoking status, socioeconomic status and gender. Results: Among 10 PFC compounds considered, only perfluorohexanoic acid (PFHxA) was seen at a significantly higher concentration in GS men and women. Conclusion: PFHxA exposure may be associated with GS. Our findings do not support increased exposure in GS for other PFCs. - Highlights: • Most serum PFCs are not associated with clinically evident Gilbert syndrome. • However, serum perfluorohexanoic acid is positively associated. • The investigation addresses the clinical presentation, not the genetic mutation.« less

Spatial and temporal patterns in concentrations of perfluorinated compounds in bald eagle nestlings in the Upper Midwestern United States

USGS Publications Warehouse

Route, William T.; Russell, Robin E.; Lindstrom, Andrew B.; Strynor, Mark J.; Key, Rebecca L.

2014-01-01

Perfluorinated chemicals (PFCs) are of concern due to their widespread use, persistence in the environment, tendency to accumulate in animal tissues, and growing evidence of toxicity. Between 2006 and 2011 we collected blood plasma from 261 bald eagle nestlings in six study areas from the upper Midwestern United States. Samples were assessed for levels of 16 different PFCs. We used regression analysis in a Bayesian framework to evaluate spatial and temporal trends for these analytes. We found levels as high as 7370 ng/mL for the sum of all 16 PFCs (∑PFCs). Perfluorooctanesulfonate (PFOS) and perfluorodecanesulfonate (PFDS) were the most abundant analytes, making up 67% and 23% of the PFC burden, respectively. Levels of ∑PFC, PFOS, and PFDS were highest in more urban and industrial areas, moderate on Lake Superior, and low on the remote upper St. Croix River watershed. We found evidence of declines in ∑PFCs and seven analytes, including PFOS, PFDS, and perfluorooctanoic acid (PFOA); no trend in two analytes; and increases in two analytes. We argue that PFDS, a long-chained PFC with potential for high bioaccumulation and toxicity, should be considered for future animal and human studies.

Bioaccumulation of perfluorochemicals in sediments by the aquatic oligochaete Lumbriculus variegatus.

PubMed

Higgins, Christopher P; McLeod, Pamela B; MacManus-Spencer, Laura A; Luthy, Richard G

2007-07-01

Bioaccumulation of perfluoroalkyl sulfonates, perfluorocarboxylates, and 2-(N-ethylperfluorooctane sulfonamido) acetic acid (N-EtFOSAA) from laboratory-spiked and contaminated field sediments was assessed using the freshwater oligochaete, Lumbriculus variegatus. Semistatic batch experiments were conducted to monitor the biological uptake of these perfluorochemicals (PFCs) over 56 days. The elimination of PFCs was measured as the loss of PFCs in L. variegatus exposed to PFC-spiked sediment for 28 days and then transferred to clean sediment. The resultant data suggest that PFCs in sediments are readily bioavailable and that bioaccumulation from sediments does not continually increase with increasing perfluorocarbon chain length. Perfluorooctane sulfonate (PFOS) and perfluorononanoate were the most bioaccumulative PFCs, as measured by laboratory-based estimated steady-state biota sediment accumulation factors (BSAFs) and BSAFs measured using contaminated field sediments. Elimination rate constants for perfluoroalkyl sulfonates and perfluorocaroboxylates were generally smaller than those previously measured for other organic contaminants. Last, a PFOS precursor, N-EtFOSAA, accumulated in the worm tissues and appeared to undergo biotransformation to PFOS and other PFOS precursors. This suggests that N-EtFOSAA, which has been detected in sediments and sludge often at levels exceeding PFOS, may contribute to the bioaccumulation of PFOS in aquatic organisms.

Exposure to perfluorinated compounds in Catalonia, Spain, through consumption of various raw and cooked foodstuffs, including packaged food.

PubMed

Jogsten, Ingrid Ericson; Perelló, Gemma; Llebaria, Xavier; Bigas, Esther; Martí-Cid, Roser; Kärrman, Anna; Domingo, José L

2009-07-01

In this study, the role that some food processing and packaging might play as a source of perfluorinated compounds (PFCs) through the diet was assessed. The levels of PFCs were determined in composite samples of veal steak (raw, grilled, and fried), pork loin (raw, grilled, and fried), chicken breast (raw, grilled, and fried), black pudding (uncooked), liver lamb (raw), marinated salmon (home-made and packaged), lettuce (fresh and packaged), pate of pork liver, foie gras of duck, frankfurt, sausages, chicken nuggets (fried), and common salt. Among the 11 PFCs analyzed, only PFHxS, PFOS, PFHxA, and PFOA were detected in at least one composite sample, while the levels of the remaining PFCs (PFBuS, PFHpA, PFNA, PFDA, PFUnDA, and PFDoDA) were under their respective detection limits. PFOS was the compound most frequently detected, being found in 8 of the 20 food items analyzed, while PFHxA was detected in samples of raw veal, chicken nuggets, frankfurt, sausages, and packaged lettuce. According to the results of the present study, it is not sufficiently clear if cooking with non-stick cookware, or packaging some foods, could contribute to a higher human exposure to PFCs.

PFCA Article Testing

EPA Science Inventory

The U.S. Environmental Protection Agency (EPA) has established an ongoing effort to quantify possible changes in levels of perfluorinated chemicals (PFCs) in articles of commerce (AOCs). Temporal trends in the concentrations of selected PFCs, including perfluorooctanoic acid (PFO...

The effects of embedded piezoelectric fiber composite sensors on the structural integrity of glass-fiber-epoxy composite laminate

NASA Astrophysics Data System (ADS)

Konka, Hari P.; Wahab, M. A.; Lian, K.

2012-01-01

Piezoelectric fiber composite sensors (PFCSs) made from micro-sized lead zirconate titanate (PZT) fibers have many advantages over the traditional bulk PZT sensors for embedded sensor applications. PFCSs as embedded sensors will be an ideal choice to continuously monitor the stress/strain levels and health conditions of composite structures. PFCSs are highly flexible, easily embeddable, have high compatibility with composite structures, and also provides manufacturing flexibility. This research is focused on examining the effects of embedding PFCS sensors (macro-fiber composite (MFC) and piezoelectric fiber composite (PFC)) on the structural integrity of glass-fiber-epoxy composite laminates. The strengths of composite materials with embedded PFCSs and conventional PZT sensors were compared, and the advantages of PFCS sensors over PZTs were demonstrated. Initially a numerical simulation study is performed to understand the local stress/strain field near the embedded sensor region inside a composite specimen. High stress concentration regions were observed near the embedded sensor corner edge. Using PFCS leads to a reduction of 56% in longitudinal stress concentration and 38% in transverse stress concentration, when compared to using the conventional PZTs as embedded sensors. In-plane tensile, in-plane tension-tension fatigue, and short beam strength tests are performed to evaluate the strengths/behavior of the composite specimens containing embedded PFCS. From the tensile test it is observed that embedding PFCS and PZT sensors in the composite structures leads to a reduction in ultimate strength by 3 and 6% respectively. From the fatigue test results it is concluded that both embedded PFCS and PZT sensors do not have a significant effect on the fatigue behavior of the composite specimens. From the short beam strength test it is found that embedding PFCS and PZT sensors leads to a reduction in shear strength by 7 and 15% respectively. Overall the pure PZT sensors seem to have low compatibility with composites when compared to PFCSs.

Perfluorinated compounds in the Antarctic region: ocean circulation provides prolonged protection from distant sources.

PubMed

Bengtson Nash, Susan; Rintoul, Stephen R; Kawaguchi, So; Staniland, Iain; van den Hoff, John; Tierney, Megan; Bossi, Rossana

2010-09-01

In order to investigate the extent to which Perfluorinated Contaminants (PFCs) have permeated the Southern Ocean food web to date, a range of Antarctic, sub-Antarctic and Antarctic-migratory biota were analysed for key ionic PFCs. Based upon the geographical distribution pattern and ecology of biota with detectable vs. non-detectable PFC burdens, an evaluation of the potential contributory roles of alternative system input pathways is made. Our analytical findings, together with previous reports, reveal only the occasional occurrence of PFCs in migratory biota and vertebrate predators with foraging ranges extending into or north of the Antarctic Circumpolar Current (ACC). Geographical contamination patterns observed correspond most strongly with those expected from delivery via hydrospheric transport as governed by the unique oceanographic features of the Southern Ocean. We suggest that hydrospheric transport will form a slow, but primary, input pathway of PFCs to the Antarctic region. Copyright (c) 2010 Elsevier Ltd. All rights reserved.

ANALYSIS OF FISH HOMOGENATES FOR PERFLUORINATED COMPOUNDS

EPA Science Inventory

Perfluorinated compounds (PFCs) which include PFOS and PFOA are widely distributed in wildlife. Whole fish homogenates were analyzed for PFCs from the upper Mississippi, the Missouri and the Ohio rivers. Methods development, validation data, and preliminary study results will b...

Multi-Platform Metabolomic Analyses of Rat Urine Following Exposure to Perfluorinated Chemicals (PFCs)

EPA Science Inventory

Perfluorinated chemicals (PFCs), namely perfluorooctanoic acid (PFOA) and perfluorooctane sulfonate (PFOS), represent an emerging class of persistent and bioaccumulative compounds. Global occurrence of these fluorochemicals, coupled with probable human exposure, has prompted inv...

Brominated Flame Retardants and Perfluorinated Chemicals

EPA Science Inventory

Brominated flame retardants (BFRs) and perfluorinated chemicals (PFCs) belong to a large class of chemicals known as organohalogens. It is believed that both BFRs and PFCs saved lives by reducing flammability of materials commonly used and bactericidal (biocidal) properties. Thes...

Long-Chain Perfluorinated Chemicals (PFCs) Action Plan

EPA Pesticide Factsheets

This Action Plan is based on EPA’s initial review of readily available use, exposure, and hazard information on PFCs. EPA considered which of the various authorities provided under TSCA and other statutes might be appropriate to address potential concerns.

40 CFR 98.300 - Definition of the source category.

Code of Federal Regulations, 2011 CFR

2011-07-01

... insulated with or containing sulfur hexafluoride (SF6) or perfluorocarbons (PFCs) used within an electric...-pressure and hermetically sealed-pressure switchgear and gas-insulated lines containing SF6 or PFCs. (4...) Other containers of SF6 or PFC. ...

40 CFR 98.300 - Definition of the source category.

Code of Federal Regulations, 2014 CFR

2014-07-01

... insulated with or containing sulfur hexafluoride (SF6) or perfluorocarbons (PFCs) used within an electric...-pressure and hermetically sealed-pressure switchgear and gas-insulated lines containing SF6 or PFCs. (4...) Other containers of SF6 or PFC. ...

40 CFR 98.300 - Definition of the source category.

Code of Federal Regulations, 2013 CFR

2013-07-01

... insulated with or containing sulfur hexafluoride (SF6) or perfluorocarbons (PFCs) used within an electric...-pressure and hermetically sealed-pressure switchgear and gas-insulated lines containing SF6 or PFCs. (4...) Other containers of SF6 or PFC. ...

40 CFR 98.300 - Definition of the source category.

Code of Federal Regulations, 2012 CFR

2012-07-01

... insulated with or containing sulfur hexafluoride (SF6) or perfluorocarbons (PFCs) used within an electric...-pressure and hermetically sealed-pressure switchgear and gas-insulated lines containing SF6 or PFCs. (4...) Other containers of SF6 or PFC. ...

Transactivation potencies of the Baikal seal (Pusa sibirica) peroxisome proliferator-activated receptor α by perfluoroalkyl carboxylates and sulfonates: estimation of PFOA induction equivalency factors.

PubMed

Ishibashi, Hiroshi; Kim, Eun-Young; Iwata, Hisato

2011-04-01

The present study assessed the transactivation potencies of the Baikal seal (Pusa sibirica) peroxisome proliferator-activated receptor α (BS PPARα) by perfluorochemicals (PFCs) having various carbon chain lengths (C4-C12) using an in vitro reporter gene assay. Among the twelve PFCs treated with a range of 7.8-250 μM concentration, eight perfluoroalkyl carboxylates (PFCAs) and two perfluoroalkyl sulfonates (PFSAs) induced BS PPARα-mediated transcriptional activities in a dose-dependent manner. To compare the BS PPARα transactivation potencies of PFCs, the present study estimated the PFOA induction equivalency factors (IEFs), a ratio of the 50% effective concentration of PFOA to the concentration of each compound that can induce the response corresponding to 50% of the maximal response of PFOA. The order of IEFs for the PFCs was as follows: PFOA (IEF: 1)>PFHpA (0.89)>PFNA (0.61)>PFPeA (0.50)>PFHxS (0.41)>PFHxA (0.38)≈PFDA (0.37)>PFBA (0.26)=PFOS (0.26)>PFUnDA (0.15)≫PFDoDA and PFBuS (not activated). The structure-activity relationship analysis showed that PFCAs having more than seven perfluorinated carbons had a negative correlation (r=-1.0, p=0.017) between the number of perfluorinated carbons and the IEF of PFCAs, indicating that the number of perfluorinated carbon of PFCAs is one of the factors determining the transactivation potencies of the BS PPARα. The analysis also indicated that PFCAs were more potent than PFSAs with the same number of perfluorinated carbons. Treatment with a mixture of ten PFCs showed an additive action on the BS PPARα activation. Using IEFs of individual PFCs and hepatic concentrations of PFCs in the liver of wild Baikal seals, the PFOA induction equivalents (IEQs, 5.3-58 ng IEQ/g wet weight) were calculated. The correlation analysis revealed that the hepatic total IEQs showed a significant positive correlation with the hepatic expression levels of cytochrome P450 4A-like protein (r=0.53, p=0.036). This suggests that our approach may be useful for assessing the potential PPARα-mediated biological effects of complex mixtures of PFCs in wild Baikal seal population.

Defect annealing and thermal desorption of deuterium in low dose HFIR neutron-irradiated tungsten

DOE Office of Scientific and Technical Information (OSTI.GOV)

Masashi Shimada; M. Hara; T. Otsuka

2014-05-01

Accurately estimating tritium retention in plasma facing components (PFCs) and minimizing its uncertainty are key safety issues for licensing future fusion power reactors. D-T fusion reactions produce 14.1 MeV neutrons that activate PFCs and create radiation defects throughout the bulk of the material of these components. Recent studies show that tritium migrates and is trapped in bulk (>> 10 µm) tungsten beyond the detection range of nuclear reaction analysis technique [1-2], and thermal desorption spectroscopy (TDS) technique becomes the only established diagnostic that can reveal hydrogen isotope behavior in in bulk (>> 10 µm) tungsten. Radiation damage and its recoverymore » mechanisms in neutron-irradiated tungsten are still poorly understood, and neutron-irradiation data of tungsten is very limited. In this paper, systematic investigations with repeated plasma exposures and thermal desorption are performed to study defect annealing and thermal desorption of deuterium in low dose neutron-irradiated tungsten. Three tungsten samples (99.99 at. % purity from A.L.M.T. Co., Japan) irradiated at High Flux Isotope Reactor at Oak Ridge National Laboratory were exposed to high flux (ion flux of (0.5-1.0)x1022 m-2s-1 and ion fluence of 1x1026 m-2) deuterium plasma at three different temperatures (100, 200, and 500 °C) in Tritium Plasma Experiment at Idaho National Laboratory. Subsequently, thermal desorption spectroscopy (TDS) was performed with a ramp rate of 10 °C/min up to 900 °C, and the samples were annealed at 900 °C for 0.5 hour. These procedures were repeated three (for 100 and 200 °C samples) and four (for 500 °C sample) times to uncover damage recovery mechanisms and its effects on deuterium behavior. The results show that deuterium retention decreases approximately 90, 75, and 66 % for 100, 200, and 500 °C, respectively after each annealing. When subjected to the same TDS recipe, the desorption temperature shifts from 800 °C to 600 °C after 1st annealing for the sample exposed to TPE at 500 °C. Tritium Migration Analysis Program (TMAP) analysis reveals that the detrapping energy decreases from 1.8 eV to 1.4 eV, indicating the changes in trapping mechanisms. This paper also summarizes deuterium behavior studies in HFIR neutron-irradiated tungsten under US-Japan TITAN program.« less

Development of a Fast Valve for Disruption Mitigation and its Preliminary Application to EAST and HT-7

NASA Astrophysics Data System (ADS)

Zhuang, Huidong; Zhang, Xiaodong

2013-08-01

In large tokamaks, disruption of high current plasma would damage plasma facing component surfaces (PFCs) or other inner components due to high heat load, electromagnetic force load and runaway electrons. It would also influence the subsequent plasma discharge due to production of impurities during disruptions. So the avoidance and mitigation of disruptions is essential for the next generation of tokamaks, such as ITER. Massive gas injection (MGI) is a promising method of disruption mitigation. A new fast valve has been developed successfully on EAST. The valve can be opened in 0.5 ms, and the duration of open state is largely dependent on the gas pressure and capacitor voltage. The throughput of the valve can be adjusted from 0 mbar·L to 700 mbar·L by changing the capacitor voltage and gas pressure. The response time and throughput of the fast valve can meet the requirement of disruption mitigation on EAST. In the last round campaign of EAST and HT-7 in 2010, the fast valve has operated successfully. He and Ar was used for the disruption mitigation on HT-7. By injecting the proper amount of gas, the current quench rate could be slowed down, and the impurities radiation would be greatly improved. In elongated plasmas of EAST discharges, the experimental data is opposite to that which is expected.

(CHINA) PERFLUORINATED ORGANIC COMPOUND EXPOSURE ASSESSMENT RESEARCH

EPA Science Inventory

A wide range of perfluorinated organic compounds (PFCs) has been used in a variety of industrial processes and consumer products. The most commonly studied PFCs include perfluorooctane sulfonate (PFOS) and perfluorooctanoic acid (PFOA), but there are many more compounds in this c...

PERFLUORINATED ORGANIC COMPOUND EXPOSURE ASSESSMENT RESEARCH

EPA Science Inventory

A wide range of perfluorinated organic compounds (PFCs) has been used in a variety of industrial processes and consumer products. The most commonly studied PFCs include perfluorooctane sulfonate (PFOS) and perfluorooctanoic acid (PFOA), but there are many more compounds in this c...

DETERMINATION OF PERFLUORINATED CHEMICALS (PFCS) IN SOILS, SEDIMENT AND OTHER MATRICES

EPA Science Inventory

Soils that receive land application of treated wastewater from carpet manufacturing plants were sampled for perfluorooctanoic acid (PFOA) and other perfluorinated chemicals (PFCs) that are potential degradation products of fluorotelomer-based polymers (FBPs). Soils from other pot...

PERFLUORINATED COMPOUNDS IN THE CAPE FEAR DRAINAGE BASIN IN NORTH CAROLINA

EPA Science Inventory

Concern over perfluorinated organic compounds (PFCs), e.g., perfluorooctane sulfonate (PFOS) and perfluorooctanoic acid (PFOA), is due to a number of recent studies which show that the PFCs are persistent, bioaccumulative, and toxic. Despite sustained interest in this topic, lit...

Brominated flame retardants and perfluorinated chemicals

EPA Science Inventory

Brominated flame retardants (BFRs) and perfluorinated chemicals (PFCs) belong to a class of chemicals known as organohalogens. It is believed that use of both BFRs and PFCs has resulted in lives saved by reducing flammability of materials commonly used and also due to their bacte...

Factors Affecting the Distribution of Perfluorinated Compounds in Sediments from Lake Shihwa, Korea

EPA Science Inventory

Perfluorinated compounds (PFCs) are ubiquitously distributed in various environmental media including water, soil, sediment, and biota. PFCs have also been shown to biomagnify in both aquatic and terrestrial environments. Lake Shihwa is an artificial saltwater lake, located on ...

Noninvasive Imaging of Early Venous Thrombosis by 19F Magnetic Resonance Imaging With Targeted Perfluorocarbon Nanoemulsions.

PubMed

Temme, Sebastian; Grapentin, Christoph; Quast, Christine; Jacoby, Christoph; Grandoch, Maria; Ding, Zhaoping; Owenier, Christoph; Mayenfels, Friederike; Fischer, Jens W; Schubert, Rolf; Schrader, Jürgen; Flögel, Ulrich

2015-04-21

Noninvasive detection of deep venous thrombi and subsequent pulmonary thromboembolism is a serious medical challenge, since both incidences are difficult to identify by conventional ultrasound techniques. Here, we report a novel technique for the sensitive and specific identification of developing thrombi using background-free 19F magnetic resonance imaging, together with α2-antiplasmin peptide (α2AP)-targeted perfluorocarbon nanoemulsions (PFCs) as contrast agent, which is cross-linked to fibrin by active factor XIII. Ligand functionality was ensured by mild coupling conditions using the sterol-based postinsertion technique. Developing thrombi with a diameter<0.8 mm could be visualized unequivocally in the murine inferior vena cava as hot spots in vivo by simultaneous acquisition of anatomic matching 1H and 19F magnetic resonance images at 9.4 T with both excellent signal-to-noise and contrast-to-noise ratios (71±22 and 17±5, respectively). Furthermore, α2AP-PFCs could be successfully applied for the diagnosis of experimentally induced pulmonary thromboembolism. In line with the reported half-life of factor XIIIa, application of α2AP-PFCs>60 minutes after thrombus induction no longer resulted in detectable 19F magnetic resonance imaging signals. Corresponding results were obtained in ex vivo generated human clots. Thus, α2AP-PFCs can visualize freshly developed thrombi that might still be susceptible to pharmacological intervention. Our results demonstrate that 1H/19F magnetic resonance imaging, together with α2AP-PFCs, is a sensitive, noninvasive technique for the diagnosis of acute deep venous thrombi and pulmonary thromboemboli. Furthermore, ligand coupling by the sterol-based postinsertion technique represents a unique platform for the specific targeting of PFCs for in vivo 19F magnetic resonance imaging. © 2015 American Heart Association, Inc.

DESTABILIZATION OF A SOLAR PROMINENCE/FILAMENT FIELD SYSTEM BY A SERIES OF EIGHT HOMOLOGOUS ERUPTIVE FLARES LEADING TO A CME

DOE Office of Scientific and Technical Information (OSTI.GOV)

Panesar, Navdeep K.; Moore, Ronald L.; Sterling, Alphonse C.

2015-09-20

Homologous flares are flares that occur repetitively in the same active region, with similar structure and morphology. A series of at least eight homologous flares occurred in active region NOAA 11237 over 2011 June 16–17. A nearby prominence/filament was rooted in the active region, and situated near the bottom of a coronal cavity. The active region was on the southeast solar limb as seen from the Solar Dynamics Observatory/Atmospheric Imaging Assembly, and on the disk as viewed from the Solar TErrestrial RElations Observatory/EUVI-B. The dual perspective allows us to study in detail behavior of the prominence/filament material entrained in themore » magnetic field of the repeatedly erupting system. Each of the eruptions were mainly confined, but expelled hot material into the prominence/filament cavity system (PFCS). The field carrying and containing the ejected hot material interacted with the PFCS and caused it to inflate, resulting in a step-wise rise of the PFCS approximately in step with the homologous eruptions. The eighth eruption triggered the PFCS to move outward slowly, accompanied by a weak coronal dimming. As this slow PFCS eruption was underway, a final “ejective” flare occurred in the core of the active region, resulting in strong dimming in the EUVI-B images and expulsion of a coronal mass ejection (CME). A plausible scenario is that the repeated homologous flares could have gradually destabilized the PFCS, and its subsequent eruption removed field above the acitive region and in turn led to the ejective flare, strong dimming, and CME.« less

Perfluorinated compounds in surface waters of Shanghai, China: Source analysis and risk assessment.

PubMed

Sun, Rui; Wu, Minghong; Tang, Liang; Li, Jiajun; Qian, Zhaoqiu; Han, Tao; Xu, Gang

2018-03-01

17 perfluorinated compounds (PFCs) were systematically investigated in the surface water from principal watersheds of Shanghai, China. 10 PFCs were above the detection limit (0.08-0.28ng/L) in 39 surface water samples. The perfluorooctanoic acid (PFOA) and perfluorobutanesulfonate (PFBS) were the two dominant compounds with a median concentration 50.67ng/L and 29.84ng/L, respectively. Concentrations of perfluorooctanesulfonate (PFOS) were generally less than PFBS, which might result from the global phase-out of PFOS production and the use of PFBS as a substitute for PFOS-based products. There were three major polluted areas of PFOA along the Huangpu River. The PFOA concentration in groundwater samples collected from one of the three areas indicated that chemical industry might be the possible source. The perfluoroalkane sulfonates (PFSAs) level had a spatial trend that indicated northwest had higher concentrations than the southeast. The distribution of PFCs was not much affected by atmospheric deposition. Mass loading analysis in the surface water revealed that the Huangpu River exhibited relatively large mass loading of total PFCs of 1742.43kg/year to Yangtze River Estuary. The predominant of the PFC species was PFOA with 652.65kg/year. The current concentrations of PFOA and PFOS were at middle level comparing to other studies in China and worldwide. Risk assessment of 6 PFCs showed that there is no risk to the aquatic organisms in Shanghai. PFOS and PFBS had low risk to the avian. Furthermore, the adults living in Shanghai were at low risk to exposure to PFCs through water consumption. Copyright © 2017 Elsevier Inc. All rights reserved.

High-Z material erosion and its control in DIII-D carbon divertor

DOE PAGES

Ding, Rui; Rudakov, Dimitry L.; Stangeby, Peter C.; ...

2017-03-16

It is expected that high-Z materials will be used as plasma-facing components (PFCs) in future fusion devices, making the erosion of high-Z material a key issue for high-power, long pulse operation. High-Z material erosion and redeposition have been studied using tungsten and molybdenum coated samples exposed in well-diagnosed DIII-D divertor plasma discharges. By coupling dedicated experiments and modelling using the 3D Monte Carlo code ERO, the roles of sheath potential and background carbon impurities in determining high-Z material erosion are identified. Different methods suggested by modelling have been investigated to control high-Z material erosion in DIII-D experiments. The erosion ofmore » Mo and W are found to be strongly suppressed by local injection of methane and deuterium gases. The 13C deposition resulting from local 13CH 4 injection also provides information on radial transport due to E×B drifts and cross field diffusion. Finally, D 2 gas puffing is found to cause 2 local plasma perturbation, suppressing W erosion because of the lower effective sputtering yield of W at lower plasma temperature and for higher carbon concentration in the mixed surface layer.« less

Wall Conditioning Characterization in NSTX-U

NASA Astrophysics Data System (ADS)

Caron, D.; Soukhanovskii, V.; Scotti, F.; Weller, M.

2016-10-01

Impurities in tokamak plasmas can lead to disruptive instabilities due to radiative energy loss which impede access to high-confinements mode. One source of impurities in NSTX-U are water molecules trapped in graphite plasma facing components (PFCs), which make up the walls and divertors. Hydrogen and oxygen impurities are released into the plasma due to plasma surface interactions. Extreme ultraviolet (EUV) and visible spectrometers are used in conjunction with a residual gas analyzer (RGA) to characterize the source and amount of released impurities. A high resolution visible spectrometer measured H/D Balmer- α intensity ratio on the inner wall, the upper and lower divertors, and provided a hydrogen time history for shot-to-shot trends. The RGA provided partial pressure trends of masses 2 (H2) , 16 (O2) , and 18 (H2O). Trends of O VIII and C VI spectral line intensities from the core plasma were obtained from the EUV spectrometer. The trends are correlated with wall conditioning, namely helium glow discharge cleaning and boronization. Using these trends, impurity content monitoring and recommendations for wall conditioning can be implemented. Work supported by DOE under Contracts DE-AC52-07NA27344 and DE-AC02-09CH11466.

Spectroscopic determinations of carbon fluxes, sources, and shielding in the DIII-D divertors

NASA Astrophysics Data System (ADS)

Isler, R. C.; Colchin, R. J.; Brooks, N. H.; Evans, T. E.; West, W. P.; Whyte, D. G.

2001-10-01

The most important mechanisms for eroding plasma-facing components (PFCs) and introducing carbon into tokamak divertors are believed to be physical sputtering, chemical sputtering, sublimation, and radiation enhance sublimation (RES). The relative importance of these processes has been investigated by analyzing the spectral emission rates and the effective temperatures of CI, CD, and C2 under several operating conditions in the DIII-D tokamak [Plasma Physics Controlled Nuclear Fusion Research, 1986 (International Atomic Energy Agency, Vienna, 1987), Vol. I, p. 159; Proceedings of the 18th IEEE/NPSS Symposium on Fusion Engineering, Albuquerque (Institute of Electrical and Electronic Engineers, Piscataway, 1999), p. 515]. Discrimination of chemical sputtering from physical sputtering is accomplished by quantitatively relating the fraction of CI influxes expected from dissociation of hydrocarbons to the measured CD and C2 influxes. Characteristics of sublimation are studied from carbon test samples heated to surface temperatures exceeding 2000 K. The shielding efficiency of carbon produced at the divertor target is assessed from comparison of fluxes of neutral atoms and ions; approximately 95% of the primary influx appears to be redeposited before being transported far enough upstream to fuel the core plasma.

Spectroscopic determinations of carbon fluxes, sources, and shielding in the DIII-D divertors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Isler, R. C.; Colchin, R. J.; Brooks, N. H.

2001-10-01

The most important mechanisms for eroding plasma-facing components (PFCs) and introducing carbon into tokamak divertors are believed to be physical sputtering, chemical sputtering, sublimation, and radiation enhance sublimation (RES). The relative importance of these processes has been investigated by analyzing the spectral emission rates and the effective temperatures of CI, CD, and C{sub 2} under several operating conditions in the DIII-D tokamak [Plasma Physics Controlled Nuclear Fusion Research, 1986 (International Atomic Energy Agency, Vienna, 1987), Vol. I, p. 159; Proceedings of the 18th IEEE/NPSS Symposium on Fusion Engineering, Albuquerque (Institute of Electrical and Electronic Engineers, Piscataway, 1999), p. 515]. Discriminationmore » of chemical sputtering from physical sputtering is accomplished by quantitatively relating the fraction of CI influxes expected from dissociation of hydrocarbons to the measured CD and C{sub 2} influxes. Characteristics of sublimation are studied from carbon test samples heated to surface temperatures exceeding 2000 K. The shielding efficiency of carbon produced at the divertor target is assessed from comparison of fluxes of neutral atoms and ions; approximately 95% of the primary influx appears to be redeposited before being transported far enough upstream to fuel the core plasma.« less

PERFLUORINATED COMPOUNDS IN ARCHIVED HOUSE-DUST SAMPLES

EPA Science Inventory

Archived house-dust samples were analyzed for 13 perfluorinated compounds (PFCs). Results show that PFCs are found in house-dust samples, and the data are log-normally distributed. PFOS/PFOA were present in 94.6% and 96.4% of the samples respectively. Concentrations ranged fro...

Brominated flame retardants and perfluorinated chemicals- Vet Tox

EPA Science Inventory

Brominated flame retardants (BFRs) and perfluorinated chemicals (PFCs) belong to a class of chemicals known as organohalogens. It is believed that use of both BFRs and PFCs has resulted in lives saved by reducing flammability of materials commonly used and also due to their bacte...

PFC Emissions from Detected Versus Nondetected Anode Effects in the Aluminum Industry

NASA Astrophysics Data System (ADS)

Wong, David S.; Fraser, Paul; Lavoie, Pascal; Kim, Jooil

2015-02-01

Perfluorinated carbon compounds (PFCs) CF4 and C2F6 are potent greenhouse gases that are generated in aluminum reduction cells during events known as anode effects (AEs). Since the 1990s, the aluminum industry has made considerable progress in reducing PFCs from conventionally defined and detected AEs. However in recent years, the industry has noted the presence of unaccounted PFCs that are generated outside the conventional AE definition. Two additional AE categories have been proposed, namely low-voltage, propagating AEs (LVP-AEs) and nonpropagating AEs (NP-AEs) that relate to continuous, background levels of PFC emissions. These unaccounted PFC phenomena may help explain the recent discrepancy between industry accounting and atmospheric measurements of global PFC emissions. Estimates from AGAGE, a global network of atmospheric observatories, suggest as much as 50% underaccounting of PFCs by the aluminum industry in the 2006-2010 period. The following work reviews this discrepancy and the potential role played by LVP-AEs and NP-AEs.

Complete Defluorination of Perfluorinated Compounds by Hydrated Electrons Generated from 3-Indole-acetic-acid in Organomodified Montmorillonite

PubMed Central

Tian, Haoting; Gao, Juan; Li, Hui; Boyd, Stephen A.; Gu, Cheng

2016-01-01

Here we describe a unique process that achieves complete defluorination and decomposition of perfluorinated compounds (PFCs) which comprise one of the most recalcitrant and widely distributed classes of toxic pollutant chemicals found in natural environments. Photogenerated hydrated electrons derived from 3-indole-acetic-acid within an organomodified clay induce the reductive defluorination of co-sorbed PFCs. The process proceeds to completion within a few hours under mild reaction conditions. The organomontmorillonite clay promotes the formation of highly reactive hydrated electrons by stabilizing indole radical cations formed upon photolysis, and prevents their deactivation by reaction with protons or oxygen. In the constrained interlayer regions of the clay, hydrated electrons and co-sorbed PFCs are brought in close proximity thereby increasing the probability of reaction. This novel green chemistry provides the basis for in situ and ex situ technologies to treat one of the most troublesome, recalcitrant and ubiquitous classes of environmental contaminants, i.e., PFCs, utilizing innocuous reagents, naturally occurring materials and mild reaction conditions. PMID:27608658

Exposure and effects of perfluoroalkyl compounds on tree swallows nesting at Lake Johanna in east central Minnesota, USA

USGS Publications Warehouse

Custer, Christine M.; Custer, Thomas W.; Schoenfuss, Heiko L.; Poganski, Beth H.; Solem, Laura

2012-01-01

Tree swallow (Tachycineta bicolor) samples were collected at a reference lake and a nearby lake (Lake Johanna) in east central Minnesota, USA contaminated with perfluorinated carboxylic and sulfonic acids. Tissues were analyzed for a suite of 13 perfluoroalkyl compounds (PFCs) to quantify exposure and to determine if there was an association between egg concentrations of PFCs and reproductive success of tree swallows. Concentrations of perfluoroocatane sulfonate (PFOS) were elevated in all tree swallow tissues from Lake Johanna compared to tissues collected at the reference lake. Other PFCs, except for two, were elevated in blood plasma at Lake Johanna compared to the reference lake. PFOS was the dominant PFC (>75%) at Lake Johanna, but accounted for <50% of total PFCs at the reference lake. There was a negative association between concentrations of PFOS in eggs and hatching success. Reduced hatching success was associated with PFOS levels as low as 150 ng/g wet weight.

Occurrence of perfluorinated compounds (PFCs) in drinking water of North Rhine-Westphalia, Germany and new approach to assess drinking water contamination by shorter-chained C4-C7 PFCs.

PubMed

Wilhelm, Michael; Bergmann, Sabine; Dieter, Hermann H

2010-06-01

After detection of perfluorooctanoate (PFOA) in drinking water at concentrations up to 0.64 microg/l in Arnsberg, Sauerland, Germany, the German Drinking Water Commission (TWK) assessed perfluorinated compounds (PFCs) in drinking water and set for the first time worldwide in June 2006 a health-based guide value for safe lifelong exposure at 0.3 microg/l (sum of PFOA and perfluorooctanesulfonate, PFOS). PFOA and PFOS can be effectively removed from drinking water by percolation over granular activated carbon. Additionally, recent EU-regulations require phasing out use of PFOS and ask to voluntarily reduce the one of PFOA. New and shorter-chained PFCs (C4-C7) and their mixtures are being introduced as replacements. We assume that some of these "new" compounds could be main contributors to total PFC levels in drinking water in future, especially since short-chained PFCs are difficult to remove from drinking water by common treatment techniques and also by filtration over activated carbon. The aims of the study were to summarize the data from the regularly measured PFC levels in drinking water and in the drinking water resources in North Rhine-Westphalia (NRW) for the sampling period 2008-2009, to give an overview on the general approach to assess PFC mixtures and to assess short-chained PFCs by using toxicokinetic instead of (sub)chronic data. No general increase of substitutes for PFOS and PFOA in wastewater and surface water was detected. Present findings of short-chained PFC in drinking waters in NRW were due to extended analysis and caused by other impacts. Additionally, several PFC contamination incidents in drinking water resources (groundwater and rivers) have been reported in NRW. The new approach to assess short-chained PFCs is based on a ranking of their estimated half-lives for elimination from the human body. Accordingly, we consider the following provisional health-related indication values (HRIV) as safe in drinking water for lifelong exposure: perfluorobutanoate (PFBA) 7 microg/l, perfluoropentanoate (PFPA) 3 microg/l, perfluorohexanoate (PFHxA) 1 microg/l, perfluoroheptanoate (PFHpA) 0.3 microg/l, perfluorobutanesulfonate (PFBS) 3 microg/l, perfluoropentanesulfonate (PFPS) 1 microg/l, perfluorohexanesulfonate (PFHxS) 0.3 microg/l and perfluoroheptanesulfonate (PFHpS) 0.3 microg/l. For all PFCs the long-term lowest maximal quality goal (general precautionary value, PVg) in drinking water is set to -0.1 microg/l.

PERFLUORINATED COMPOUNDS (PFCs) IN SERUM OF ...

EPA Pesticide Factsheets

The PFCs have been used in a wide range of consumer, including residential, products (e.g., stain-resistant coatings for carpets and upholstery). Carbon-fluoride bonds are highly stable, mak-ing PFCs extremely resistant to biodegradation. Thus, PFCs have become globally distributed and are ubiquitously present in serum of wildlife and people. Despite this, comparatively little is known as to how people are primarily exposed, and what (if any) health risk is associated with chronic, low-level exposure. It is hypothesized that house dust may represent a significant exposure route because PFCs can slough or volatilize from products used indoors, subsequently adsorbing to and accumulating within house dust. The purpose of this study was to determine if PFC serum levels in domestic cats tended to increase in proportion to time spent indoors and whether analyte patterns reflected that of food sources [e.g., fish products with high perfluoro-octane sulfonate (PFOS) but low perfluorohexanesulfonate (PFHxS)] or with house dust (PFOS + PFHxS + perfluorooctanoate (PFOA) ─ with high PFHxS levels in the most contaminated dust). In 2008, serum was obtained from feral and pet cats presenting to shelters and clinics in the Raleigh, NC area, including the NCSU VTH. PFC serum levels were measured using high-resolution time-of-flight mass spectroscopy. Data on housing status was available for 50 cats. From least to greatest indoor residential exposure, cats were grouped as

DEVELOPMENT OF AN EPA METHOD FOR PERFLUOROCALKYL COMPOUNDS IN DRINKING WATER

EPA Science Inventory

Perfluoroalkyl compounds (PFCs) have been manufactured for over 50 years and their use has dramatically increased over the years. Due to their unique properties of repelling both water and oil, PFCs have been used in a wide variety of applications. In 2001, identification of or...

14 CFR 158.81 - General.

Code of Federal Regulations, 2014 CFR

2014-01-01

... FACILITY CHARGES (PFC'S) Termination § 158.81 General. This subpart contains the procedures for termination of PFCs or loss of Federal airport grant funds for violations of this part or 49 U.S.C. 40117. This subpart does not address the circumstances under which the authority to collect PFCs may be terminated for...

14 CFR 158.81 - General.

Code of Federal Regulations, 2012 CFR

2012-01-01

... FACILITY CHARGES (PFC'S) Termination § 158.81 General. This subpart contains the procedures for termination of PFCs or loss of Federal airport grant funds for violations of this part or 49 U.S.C. 40117. This subpart does not address the circumstances under which the authority to collect PFCs may be terminated for...

14 CFR 158.81 - General.

Code of Federal Regulations, 2013 CFR

2013-01-01

... FACILITY CHARGES (PFC'S) Termination § 158.81 General. This subpart contains the procedures for termination of PFCs or loss of Federal airport grant funds for violations of this part or 49 U.S.C. 40117. This subpart does not address the circumstances under which the authority to collect PFCs may be terminated for...

14 CFR 158.81 - General.

Code of Federal Regulations, 2011 CFR

2011-01-01

... FACILITY CHARGES (PFC'S) Termination § 158.81 General. This subpart contains the procedures for termination of PFCs or loss of Federal airport grant funds for violations of this part or 49 U.S.C. 40117. This subpart does not address the circumstances under which the authority to collect PFCs may be terminated for...

14 CFR 158.81 - General.

Code of Federal Regulations, 2010 CFR

2010-01-01

... FACILITY CHARGES (PFC'S) Termination § 158.81 General. This subpart contains the procedures for termination of PFCs or loss of Federal airport grant funds for violations of this part or 49 U.S.C. 40117. This subpart does not address the circumstances under which the authority to collect PFCs may be terminated for...

40 CFR Appendix H to Subpart G of... - Substitutes Subject to Use Restrictions and Unacceptable Substitutes, Effective May 28, 1999

Code of Federal Regulations, 2011 CFR

2011-07-01

.... Actual contributions to global warming depend upon the quantities emitted. See additional comments 1, 2.... Actual contributions to global warming depend upon the quantities of PFCs emitted. See additional.... Actual contributions to global warming depend upon the quantities of PFCs emitted. See additional...

Simultaneous Determination of Perfluorinated Compounds in Edible Oil by Gel-Permeation Chromatography Combined with Dispersive Solid-Phase Extraction and Liquid Chromatography-Tandem Mass Spectrometry.

PubMed

Yang, Lili; Jin, Fen; Zhang, Peng; Zhang, Yanxin; Wang, Jian; Shao, Hua; Jin, Maojun; Wang, Shanshan; Zheng, Lufei; Wang, Jing

2015-09-30

A simple analytical method was developed for the simultaneous analysis of 18 perfluorinated compounds (PFCs) in edible oil. The target compounds were extracted by acetonitrile, purified by gel permeation chromatography (GPC) and dispersive solid-phase extraction (DSPE) using graphitized carbon black (GCB) and octadecyl (C18), and analyzed by liquid chromatography-electrospray ionization tandem mass spectrometry (LC-ES-MS/MS) in negative ion mode. Recovery studies were performed at three fortification levels. The average recoveries of all target PFCs ranged from 60 to 129%, with an acceptable relative standard deviation (RSD) (1-20%, n = 3). The method detection limits (MDLs) ranged from 0.004 to 0.4 μg/kg, which was significantly improved compared with the existing liquid-liquid extraction and cleanup method. The method was successfully applied for the analysis of all target PFCs in edible oil samples collected from markets in Beijing, China, and the results revealed that C6-C10 perfluorocarboxylic acid (PFCAs) and C7 perfluorosulfonic acid PFSAs were the major PFCs detected in oil samples.

Effects of different factors on photodefluorination of perfluorinated compounds by hydrated electrons in organo-montmorillonite system.

PubMed

Tian, Haoting; Gu, Cheng

2018-01-01

Perfluorinated compounds (PFCs) are considered as the most recalcitrant organic contaminants. Our previous research has shown that PFCs can be completely defluorinated in the UV/organoclay/3-indole acetic acid system, however, the factors that could affect the degradation of PFCs, are still not clear. In this study, we further investigated the effect of different indole derivatives and organo-modified montmorillonite on the degradation of perfluooctanoic acid (PFOA). Based on multiple linear regression analysis, our results clearly indicate that hydrated electron yields of indole derivatives, adsorption of PFOA and indole derivatives on organo-montmorillonite contributed independently to the degradation of PFOA. In addition, the results also show that the presence of humic substance (even at 10 mg C L -1 ) would not significantly suppress the degradation process due to the strong adsorption of humic substance on the organo-montmorillonite surface. This study would provide more information to design an efficient and environment-friendly system for degradation of PFCs, and this technique will have great potential for treatment of persistent contaminants under mild reaction conditions. Copyright © 2017. Published by Elsevier Ltd.

Health risks in infants associated with exposure to perfluorinated compounds in human breast milk from Zhoushan, China.

PubMed

So, Man Ka; Yamashita, Nobuyoshi; Taniyasu, Sachi; Jiang, Qinting; Giesy, John P; Chen, Kun; Lam, Paul Kwan Sing

2006-05-01

Recent studies have reported the ubiquitous distribution of perfluorinated compounds (PFCs), especially perfluorooctanesulfonate (PFOS) and perfluorooctanoic acid (PFOA), in wildlife and human whole blood or serum. In 2003 a solid phase extraction method was developed, which allowed the measurement of PFCs in human breast milk. In the present study, PFCs in samples of human breast milk from 19 individuals from Zhoushan, China, were analyzed by modifying a previously established method, based on weak-anion exchange extraction. PFOS and PFOA were the two dominant chemicals detected in all the milk samples. Concentrations of PFOS and PFOA ranged from 45 to 360 ng/L and 47 to 210 ng/L, respectively. The maximum concentrations of other PFCs were 100 ng/L for perfluorohexanesulfonate (PFHxS), 62 ng/L for perfluorononanoate (PFNA), 15 ng/L for perfluorodecanoate (PFDA) and 56 ng/L for perfluoroundecanoate (PFUnDA). Statistically significant correlations between various PFCs suggested a common exposure source to humans. No statistically significant correlation was found between concentrations of either PFOS or PFOA and maternal age, weight, or infant weight. Rate of consumption of fish was found to be positively correlated with PFNA, PFDA, and PFUnDA concentrations. Daily intake of PFOS for the child via breast milk with greater PFOS concentrations exceeded the predicted conservative reference dose in 1 of 19 samples, indicating that there may be a small potential risk of PFOS for the infants in Zhoushan via the consumption of breast milk.

Alkaline digestion and solid phase extraction method for perfluorinated compounds in mussels and oysters from South China and Japan.

PubMed

So, M K; Taniyasu, S; Lam, P K S; Zheng, G J; Giesy, J P; Yamashita, N

2006-02-01

Perfluorinated compounds (PFCs), such as perfluorooctane sulfonate (PFOS), have been identified in the coastal waters of China and Japan. An alkaline digestion method, coupled with solid-phase extraction (SPE), and high-performance liquid chromatography interfaced with high-resolution electrospray tandem mass spectrometry was developed to determine PFCs in mussel and oyster samples from coastal waters of South China and Japan. These techniques produced adequate recoveries and reporting limits with small quantities of PFCs. Concentrations of individual PFCs in mussels and oysters from South China and Japan ranged from 113.6 to 586.0 pg/g, wet weight (ww) for PFOS, 63.1 to 511.6 pg/g, ww for perfluorohexane sulfonate, 9.3 to 30.1 pg/g, ww for perfluorobutane sulfonate and 37.8 to 2957.0 pg/g, ww for perfluorooctane sulfonamide. The quantification of perfluorinated carboxylates was compromised by interferences from carboxylates in the procedural blanks. Perfluoroundecanoate and perfluorononanoate had relatively great blank interferences, which resulted in relatively poor limits of quantification for these compounds. Some PFCs were only identified in a limited number of samples: perfluorododecanoate in samples from Tokyo Bay, Japan (195.9 pg/g, ww); and perfluorodecanoate in Fuzhou, China (131.7 pg/g, ww) and Tokyo Bay (118.6 pg/g, ww). The greatest concentrations of perfluorooctanoate, perfluoroheptanoate, and perfluorohexanoate were observed in samples from Tokyo Bay and Bei Hai, South China.

[Residue of organic fluorine pollutants in hair and nails collected from Tianjin].

PubMed

Yao, Dan; Zhang, Hong; Chai, Zhi-Fang; Shen, Jin-Can; Yang, Bo; Wang, Yan-Ping; Liu, Guo-Qing

2013-02-01

In order to explore the residue and distributions of organic fluorine pollutants in hair and nails, the residue levels of total fluorine (TF), extractable organic fluorine (EOF) and perfluorinated chemicals (PFCs) in hair and nails collected from Tianjin adults were measured by the cyclic neutron activation analysis (CNAA) combined with the high performance liquid chromatography-tandem mass spectrometry (HPLC-MS/MS). The results showed that inorganic fluorine (mean: 2.0 mg.kg-1, 4.5 mg.kg-1) was the primary fluorine in TF while EOF(mean: 0.7 mg.kg-1, 1.8 mg.kg-1) was minor. The average amount of identified fluorine (IF) was 0.038 mg.kg-1 in hair and 0.047 mg.kg-1 in nails, accounting or 7.1% (2.6%-16%) and 3.5% (1.1%-11%) of EOF, respectively, which indicated that more than 84% of EOF was unknown. The major residue in hair and nails were medium-and short-chain PFCs,in which perfluorooctane sulfonate, perfluorooctanoic acid and perfluorononanoic acid were the main species. TF, EOF and IF levels in dyed and permed hair were significantly higher than untreated hair (P <0.05), and the concentrations of Sigma PFCs in hair and nails showed no difference between genders. With significantly higher levels of sigma PFCs and PFOS residues than hair (P <0.01), nails could potentially become a more sensitive bioindicator for the exposure level of PFCs in human.

Characterization and performance of a field aligned ion cyclotron range of frequency antenna in Alcator C-Mod

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wukitch, S. J.; Garrett, M. L.; Ochoukov, R.

Ion cyclotron range of frequency (ICRF) heating is expected to provide auxiliary heating for ITER and future fusion reactors where high Z metallic plasma facing components (PFCs) are being considered. Impurity contamination linked to ICRF antenna operation remains a major challenge particularly for devices with high Z metallic PFCs. Here, we report on an experimental investigation to test whether a field aligned (FA) antenna can reduce impurity contamination and impurity sources. We compare the modification of the scrape of layer (SOL) plasma potential of the FA antenna to a conventional, toroidally aligned (TA) antenna, in order to explore the underlyingmore » physics governing impurity contamination linked to ICRF heating. The FA antenna is a 4-strap ICRF antenna where the current straps and antenna enclosure sides are perpendicular to the total magnetic field while the Faraday screen rods are parallel to the total magnetic field. In principle, alignment with respect to the total magnetic field minimizes integrated E|| (electric field along a magnetic field line) via symmetry. A finite element method RF antenna model coupled to a cold plasma model verifies that the integrated E|| should be reduced for all antenna phases. Monopole phasing in particular is expected to have the lowest integrated E||. Consistent with expectations, we observed that the impurity contamination and impurity source at the FA antenna are reduced compared to the TA antenna. In both L and H-mode discharges, the radiated power is 20%–30% lower for a FA-antenna heated discharge than a discharge heated with the TA-antennas. However, inconsistent with expectations, we observe RF induced plasma potentials (via gas-puff imaging and emissive probes to be nearly identical for FA and TA antennas when operated in dipole phasing). Moreover, the highest levels of RF-induced plasma potentials are observed using monopole phasing with the FA antenna. Thus, while impurity contamination and sources are indeed reduced with the FA antenna configuration, the mechanism determining the SOL plasma potential in the presence of ICRF and its impact on impurity contamination and sources remains to be understood.« less

A Novel Way To Identify Precursors That Degrade To Perfluorinated Compounds In Activated Sludge Using Ion-Trap Time-Of-Flight Mass Spectrometry

EPA Science Inventory

An increasing number of studies have been conducted to investigate the environmental distribution of perfluorinated alkyl compounds (PFCs), many of which are known to be toxic in laboratory animals. Despite growing public concerns, fate and transport of PFCs are little known. M...

A Novel Way To Identify Precursors That Degrade To Perfluourinated Compounds In Activated Sludge Using Ion-Trap Time-Of-Flight Mass Spectrometer

EPA Science Inventory

An increasing number of studies have been conducted to investigate the environmental distribution of perfluorinated alkyl compounds (PFCs), many of which are known to be toxic in laboratory animals. Despite growing public concerns, the fate and transport of PFCs are little under...

Developing and validating advanced divertor solutions on DIII-D for next-step fusion devices

NASA Astrophysics Data System (ADS)

Guo, H. Y.; Hill, D. N.; Leonard, A. W.; Allen, S. L.; Stangeby, P. C.; Thomas, D.; Unterberg, E. A.; Abrams, T.; Boedo, J.; Briesemeister, A. R.; Buchenauer, D.; Bykov, I.; Canik, J. M.; Chrobak, C.; Covele, B.; Ding, R.; Doerner, R.; Donovan, D.; Du, H.; Elder, D.; Eldon, D.; Lasa, A.; Groth, M.; Guterl, J.; Jarvinen, A.; Hinson, E.; Kolemen, E.; Lasnier, C. J.; Lore, J.; Makowski, M. A.; McLean, A.; Meyer, B.; Moser, A. L.; Nygren, R.; Owen, L.; Petrie, T. W.; Porter, G. D.; Rognlien, T. D.; Rudakov, D.; Sang, C. F.; Samuell, C.; Si, H.; Schmitz, O.; Sontag, A.; Soukhanovskii, V.; Wampler, W.; Wang, H.; Watkins, J. G.

2016-12-01

A major challenge facing the design and operation of next-step high-power steady-state fusion devices is to develop a viable divertor solution with order-of-magnitude increases in power handling capability relative to present experience, while having acceptable divertor target plate erosion and being compatible with maintaining good core plasma confinement. A new initiative has been launched on DIII-D to develop the scientific basis for design, installation, and operation of an advanced divertor to evaluate boundary plasma solutions applicable to next step fusion experiments beyond ITER. Developing the scientific basis for fusion reactor divertor solutions must necessarily follow three lines of research, which we plan to pursue in DIII-D: (1) Advance scientific understanding and predictive capability through development and comparison between state-of-the art computational models and enhanced measurements using targeted parametric scans; (2) Develop and validate key divertor design concepts and codes through innovative variations in physical structure and magnetic geometry; (3) Assess candidate materials, determining the implications for core plasma operation and control, and develop mitigation techniques for any deleterious effects, incorporating development of plasma-material interaction models. These efforts will lead to design, installation, and evaluation of an advanced divertor for DIII-D to enable highly dissipative divertor operation at core density (n e/n GW), neutral fueling and impurity influx most compatible with high performance plasma scenarios and reactor relevant plasma facing components (PFCs). This paper highlights the current progress and near-term strategies of boundary/PMI research on DIII-D.

Developing and validating advanced divertor solutions on DIII-D for next-step fusion devices

DOE PAGES

Guo, H. Y.; Hill, D. N.; Leonard, A. W.; ...

2016-09-14

A major challenge facing the design and operation of next-step high-power steady-state fusion devices is to develop a viable divertor solution with order-of-magnitude increases in power handling capability relative to present experience, while having acceptable divertor target plate erosion and being compatible with maintaining good core plasma confinement. A new initiative has been launched on DIII-D to develop the scientific basis for design, installation, and operation of an advanced divertor to evaluate boundary plasma solutions applicable to next step fusion experiments beyond ITER. Developing the scientific basis for fusion reactor divertor solutions must necessarily follow three lines of research, whichmore » we plan to pursue in DIII-D: (1) Advance scientific understanding and predictive capability through development and comparison between state-of-the art computational models and enhanced measurements using targeted parametric scans; (2) Develop and validate key divertor design concepts and codes through innovative variations in physical structure and magnetic geometry; (3) Assess candidate materials, determining the implications for core plasma operation and control, and develop mitigation techniques for any deleterious effects, incorporating development of plasma-material interaction models. These efforts will lead to design, installation, and evaluation of an advanced divertor for DIII-D to enable highly dissipative divertor operation at core density (n e/n GW), neutral fueling and impurity influx most compatible with high performance plasma scenarios and reactor relevant plasma facing components (PFCs). In conclusion, this paper highlights the current progress and near-term strategies of boundary/PMI research on DIII-D.« less

Experimental results of near real-time protection system for plasma facing components in Wendelstein 7-X at GLADIS

NASA Astrophysics Data System (ADS)

Ali, A.; Jakubowski, M.; Greuner, H.; Böswirth, B.; Moncada, V.; Sitjes, A. Puig; Neu, R.; Pedersen, T. S.; the W7-X Team

2017-12-01

One of the aims of stellarator Wendelstein 7-X (W7-X), is to investigate steady state operation, for which power exhaust is an important issue. The predominant fraction of the energy lost from the confined plasma region will be absorbed by an island divertors, which is designed for 10 {{MWm}}-2 steady state operation. In order to protect the divertor targets from overheating, 10 state-of-the-art infrared endoscopes will be installed at W7-X. In this work, we present the experimental results obtained at the high heat flux test facility GLADIS (Garching LArge DIvertor Sample test facility in IPP Garching) [1] during tests of a new plasma facing components (PFCs) protection algorithm designed for W7-X. The GLADIS device is equipped with two ion beams that can generate a heat load in the range from 3 MWm-2 to 55 MWm-2. The algorithms developed at W7-X to detect defects and hot spots are based on the analysis of surface temperature evolution and are adapted to work in near real-time. The aim of this work was to test the near real-time algorithms in conditions close to those expected in W7-X. The experiments were performed on W7-X pre-series tiles to detect CFC/Cu delaminations. For detection of surface layers, carbon fiber composite (CFC) blocks from the divertor of the Wendelstein 7-AS stellarator were used to observe temporal behavior of fully developed surface layers. These layers of re-deposited materials, like carbon, boron, oxygen and iron, were formed during the W7-AS operation. A detailed analysis of the composition and their thermal response to high heat fluxes (HHF) are described in [2]. The experiments indicate that the automatic detection of critical events works according to W7-X PFC protection requirements.

Endoscopic ultrasound-guided transluminal drainage for peripancreatic fluid collections: where are we now?

PubMed

Kawakami, Hiroshi; Itoi, Takao; Sakamoto, Naoya

2014-07-01

Endoscopic drainage for pancreatic and peripancreatic fluid collections (PFCs) has been increasingly used as a minimally invasive alternative to surgical or percutaneous drainage. Recently, endoscopic ultrasound-guided transluminal drainage (EUS-TD) has become the standard of care and a safe procedure for nonsurgical PFC treatment. EUS-TD ensures a safe puncture, avoiding intervening blood vessels. Single or multiple plastic stents (combined with a nasocystic catheter) were used for the treatment of PFCs for EUS-TD. More recently, the use of covered self-expandable metallic stents (CSEMSs) has provided a safer and more efficient approach route for internal drainage. We focused our review on the best approach and stent to use in endoscopic drainage for PFCs. We reviewed studies of EUS-TD for PFCs based on the original Atlanta Classification, including case reports, case series, and previous review articles. Data on clinical outcomes and adverse events were collected retrospectively. A total of 93 patients underwent EUS-TD of pancreatic pseudocysts using CSEMSs. The treatment success and adverse event rates were 94.6% and 21.1%, respectively. The majority of complications were of mild severity and resolved with conservative therapy. A total of 56 patients underwent EUS-TD using CSEMSs for pancreatic abscesses or infected walled-off necroses. The treatment success and adverse event rates were 87.8% and 9.5%, respectively. EUS-TD can be performed safely and efficiently for PFC treatment. Larger diameter CSEMSs without additional fistula tract dilation for the passage of a standard scope are needed to access and drain for PFCs with solid debris.

Management of pancreatic fluid collections: A comprehensive review of the literature

PubMed Central

Tyberg, Amy; Karia, Kunal; Gabr, Moamen; Desai, Amit; Doshi, Rushabh; Gaidhane, Monica; Sharaiha, Reem Z; Kahaleh, Michel

2016-01-01

Pancreatic fluid collections (PFCs) are a frequent complication of pancreatitis. It is important to classify PFCs to guide management. The revised Atlanta criteria classifies PFCs as acute or chronic, with chronic fluid collections subdivided into pseudocysts and walled-off pancreatic necrosis (WOPN). Establishing adequate nutritional support is an essential step in the management of PFCs. Early attempts at oral feeding can be trialed in patients with mild pancreatitis. Enteral feeding should be implemented in patients with moderate to severe pancreatitis. Jejunal feeding remains the preferred route of enteral nutrition. Symptomatic PFCs require drainage; options include surgical, percutaneous, or endoscopic approaches. With the advent of newer and more advanced endoscopic tools and expertise, and an associated reduction in health care costs, minimally invasive endoscopic drainage has become the preferable approach. An endoscopic ultrasonography-guided approach using a seldinger technique is the preferred endoscopic approach. Both plastic stents and metal stents are efficacious and safe; however, metal stents may offer an advantage, especially in infected pseudocysts and in WOPN. Direct endoscopic necrosectomy is often required in WOPN. Lumen apposing metal stents that allow for direct endoscopic necrosectomy and debridement through the stent lumen are preferred in these patients. Endoscopic retrograde cholangio pancreatography with pancreatic duct (PD) exploration should be performed concurrent to PFC drainage. PD disruption is associated with an increased severity of pancreatitis, an increased risk of recurrent attacks of pancreatitis and long-term complications, and a decreased rate of PFC resolution after drainage. Any pancreatic ductal disruption should be bridged with endoscopic stenting. PMID:26900288

Perfluorinated compounds in infiltrated river rhine water and infiltrated rainwater in coastal dunes.

PubMed

Eschauzier, Christian; Haftka, Joris; Stuyfzand, Pieter J; de Voogt, Pim

2010-10-01

Different studies have shown that surface waters contain perfluorinated compounds (PFCs) in the low ng/L range. Surface waters are used to produce drinking water and PFCs have been shown to travel through the purification system and form a potential threat to human health. The specific physicochemical properties of PFCs cause them to be persistent and some of them to be bioaccumulative and toxic in the environment. This study investigates the evolvement of PFC concentrations in Rhine water and rainwater during dune water infiltration processes over a transect in the dune area of the western part of The Netherlands. The difference between infiltrated river water and rainwater in terms of PFC composition was investigated. Furthermore, isomer profiles were investigated. The compound perfluorobutanesulfonate (PFBS) was found at the highest concentrations of all PFCs investigated, up to 37 ng/L in infiltrated river water (71 ± 13% of ΣPFCs). This is in contrast with the predominant occurrence of perfluorooctanoic acid (PFOA) and perfluorooctanesulfonate (PFOS) reported in literature. The concentrations of PFBS found in infiltrated river Rhine water were significantly higher than those in infiltrated rainwater. For perfluorohexanesulfonate (PFHxS) the opposite was found: infiltrated rainwater contained more than infiltrated river water. The concentrations of PFOA, perfluorohexanoic acid (PFHxA), perfluoroheptanoic acid (PFHpA), PFBS, PFOS, and PFHxS in infiltrated river water showed an increasing trend with decreasing age of the water. The relative contribution of the branched PFOA and PFOS isomers to total concentrations of PFOA and PFOS showed a decreasing trend with decreasing age of the water.

Perfluorinated chemicals: differential toxicity, inhibition of aromatase activity and alteration of cellular lipids in human placental cells.

PubMed

Gorrochategui, Eva; Pérez-Albaladejo, Elisabet; Casas, Josefina; Lacorte, Sílvia; Porte, Cinta

2014-06-01

The cytotoxicity of eight perfluorinated chemicals (PFCs), namely, perfluorobutanoic acid (PFBA), perfluorohexanoic acid (PFHxA), perfluorooctanoic acid (PFOA), perfluorononanoic acid (PFNA), perfluorododecanoic acid (PFDoA), perfluorobutanesulfonate (PFBS), perfluorohexanesulfonate (PFHxS) and perfluorooctanesulfonate (PFOS) was assessed in the human placental choriocarcinoma cell line JEG-3. Only the long chain PFCs--PFOS, PFDoA, PFNA, PFOA--showed significant cytotoxicity in JEG-3 cells with EC50 values in the range of 107 to 647 μM. The observed cytotoxicity was to some extent related to a higher uptake of the longer chain PFCs by cells (PFDoA>PFOS≫PFNA>PFOA>PFHxA). Moreover, this work evidences a high potential of PFOS, PFOA and PFBS to act as aromatase inhibitors in placental cells with IC50s in the range of 57-80 μM, the inhibitory effect of PFBS being particularly important despite the rather low uptake of the compound by cells. Finally, exposure of JEG-3 cells to a mixture of the eight PFCs (0.6 μM each) led to a relative increase (up to 3.4-fold) of several lipid classes, including phosphatidylcholines (PCs), plasmalogen PC and lyso plasmalogen PC, which suggests an interference of PFCs with membrane lipids. Overall, this work highlights the ability of the PFC mixture to alter cellular lipid pattern at concentrations well below those that generate toxicity, and the potential of the short chain PFBS, often considered a safe substitute of PFOS, to significantly inhibit aromatase activity in placental cells. Copyright © 2014 Elsevier Inc. All rights reserved.

EMISSIONS OF FLUORINATED COMPOUNDS FROM THE ...

EPA Pesticide Factsheets

Symposium Paper One of the emerging waste streams that will likely be disposed of in combustors is carpet, due to its high heating value and combustibility. Some of the stain-resistant coatings that carpeting is treated with contain perfluorinated compounds (PFCs) such as perfluorooctanoic acid (PFOA) and their corresponding homologues (C6 – C14 acids) as well as fluorotelomer alcohols and fluoropolymers. PFOA has recently been implicated as a chemical of concern due to its toxicity. It is unknown as to whether PFCs can be released from combustion, or formed as by-products in combustors. This paper reports on a study in a 0.73 kW pilot-scale rotary kiln incinerator simulator to qualitatively and, where applicable; quantitatively assess the potential for emissions of fluorinated compounds from combustion devices. In this study, a limited number of PFCs were found in trace levels in the stack, and the concentrations were relatively independent of kiln feed, suggesting that PFCs are effectively destroyed even under mild combustion conditions, and the trace levels that were found were due to either trace contamination of the sampling duct with fluorinated compounds due to historical use of Teflon and other fluorpolymers, or sampling artifacts.

Uptake of perfluorinated compounds by plants grown in nutrient solution.

PubMed

García-Valcárcel, A I; Molero, E; Escorial, M C; Chueca, M C; Tadeo, J L

2014-02-15

The uptake rates of three perfluorinated carboxylates and three perfluorinated sufonates by a grass (B diandrus) grown in nutrient solution at two different perfluorinated compounds (PFCs) concentrations were assessed. Grass can be ingested by grazing animals causing the PFCs to enter the food chain, which is a pathway of human exposure to these compounds. A rapid and miniaturized method was developed to determine PFCs in plants, based on a matrix solid-phase dispersion (MSPD) extraction procedure followed by quantitation by HPLC-MS/MS with an MQL in the range from 1 to 9 ng/g. An increase of PFCs levels in plant was observed along the exposure time. Differences in uptake for studied perfluorinated carboxylates were found, showing a decrease with carbon chain length (from 3027 to 1,167 ng/g at the end of assay), whereas no significant differences in absorption were obtained between perfluorinated sulfonates (about 1,700 ng/g). Initially, higher PFC transfer factors (ratio between concentration in plant and concentration in initial nutrient solution) were obtained for plants growing in the nutrient solution at the highest PFC concentration, but these factors became similar with time to plants exposed to the lowest concentration. © 2013 Elsevier B.V. All rights reserved.

Fabrication and integrity test preparation of HIP-joined W and ferritic-martensitic steel mockups for fusion reactor development

NASA Astrophysics Data System (ADS)

Lee, Dong Won; Shin, Kyu In; Kim, Suk Kwon; Jin, Hyung Gon; Lee, Eo Hwak; Yoon, Jae Sung; Choi, Bo Guen; Moon, Se Youn; Hong, Bong Guen

2014-10-01

Tungsten (W) and ferritic-martensitic steel (FMS) as armor and structural materials, respectively, are the major candidates for plasma-facing components (PFCs) such as the blanket first wall (BFW) and the divertor, in a fusion reactor. In the present study, three W/FMS mockups were successfully fabricated using a hot isostatic pressing (HIP, 900 °C, 100 MPa, 1.5 hrs) with a following post-HIP heat treatment (PHHT, tempering, 750 °C, 70 MPa, 2 hrs), and the W/FMS joining method was developed based on the ITER BFW and the test blanket module (TBM) development project from 2004 to the present. Using a 10-MHz-frequency flat-type probe to ultrasonically test of the joint, we found no defects in the fabricated mockups. For confirmation of the joint integrity, a high heat flux test will be performed up to the thermal lifetime of the mockup under the proper test conditions. These conditions were determined through a preliminary analysis with conventional codes such as ANSYS-CFX for thermal-hydraulic conditions considering the test facility, the Korea heat load test facility with an electron beam (KoHLT-EB), and its water coolant system at the Korea Atomic Energy Research Institute (KAERI).

Simulating tokamak PFC performance using simultaneous dual beam particle loading with pulsed heat loading

NASA Astrophysics Data System (ADS)

Sinclair, Gregory; Gonderman, Sean; Tripathi, Jitendra; Ray, Tyler; Hassanein, Ahmed

2017-10-01

The performance of plasma facing components (PFCs) in a fusion device are expected to change due to high flux particle loading during operation. Tungsten (W) is a promising PFC candidate material, due to its high melting point, high thermal conductivity, and low tritium retention. However, ion irradiation of D and He have each shown to diminish the thermal strength of W. This work investigates the synergistic effect between ion species, using dual beam irradiation, on the thermal response of W during ELM-like pulsed heat loading. Experiments studied three different loading conditions: laser, laser + He+, and laser + He+ + D+. 100 eV He+ and D+ exposures used a flux of 3.0-3.5 x 1020 m-2 s-1. ELM-like loading was applied using a pulsed Nd:YAG laser at an energy density of 0.38-1.51 MJ m-2 (3600 1 ms pulses at 1 Hz). SEM imaging revealed that laser + He+ loading at 0.76 MJ m-2 caused surface melting, inhibiting fuzz formation. Increasing the laser fluence decreased grain size and increased surface pore density. Thermally-enhanced migration of trapped gases appear to reflect resultant molten morphology. This work was supported by the National Science Foundation PIRE project.

Measurements of impurity concentrations and transport in the Lithium Tokamak Experiment

NASA Astrophysics Data System (ADS)

Boyle, D. P.; Bell, R. E.; Kaita, R.; Lucia, M.; Schmitt, J. C.; Scotti, F.; Kubota, S.; Hansen, C.; Biewer, T. M.; Gray, T. K.

2016-10-01

The Lithium Tokamak Experiment (LTX) is a modest-sized spherical tokamak with all-metal plasma facing components (PFCs), uniquely capable of operating with large area solid and/or liquid lithium coatings essentially surrounding the entire plasma. This work presents measurements of core plasma impurity concentrations and transport in LTX. In discharges with solid Li coatings, volume averaged impurity concentrations were low but non-negligible, with 2 - 4 % Li, 0.6 - 2 % C, 0.4 - 0.7 % O, and Zeff < 1.2 . Transport was assessed using the TRANSP, NCLASS, and MIST codes. Collisions with the main H ions dominated the neoclassical impurity transport, and neoclassical transport coefficients calculated with NCLASS were similar across all impurity species and differed no more than a factor of two. However, time-independent simulations with MIST indicated that neoclassical theory did not fully capture the impurity transport and anomalous transport likely played a significant role in determining impurity profiles. Progress on additional analysis, including time-dependent impurity transport simulations and impurity measurements with liquid lithium coatings, and plans for diagnostic upgrades and future experiments in LTX- β will also be presented. This work supported by US DOE contracts DE-AC02-09CH11466 and DE-AC05-00OR22725.

Latest results and developments from the Hybrid Illinois Device for Research and Applications

NASA Astrophysics Data System (ADS)

Rizkallah, Rabel; Andruczyk, Daniel; Jeckell, Zachary Jon; Shone, Andrew John; Johnson, Daniel Scott; Allain, Jean Paul; Curreli, Davide; Ruzic, David N.; The Hidra Team

2017-10-01

The Hybrid Illinois Device for Research and Applications (HIDRA) is a five-period, l = 2, m = 5, toroidal fusion device operated at the University of Illinois at Urbana-Champaign (UIUC). It has a major radius R0 = 0.72 m and minor radius a = 0.19 m. Initial heating is achieved with 2.45 GHz electron cyclotron resonance heating (ECRH) at an on-axis magnetic field of B0 = 0.087 T which can go as high as B0 = 0.5 T. HIDRA will mainly be used as a classical stellarator, but can also run as a tokamak. This allows for both steady-state and transient regime operations. Experiments on HIDRA will primarily tackle the issue of plasma-material interactions (PMI) in fusion, and focus on developing innovative plasma facing component (PFC) technologies. Currently, research on flowing liquid lithium PFCs meant to be tested inside the machine in real-time operation, is being carried on. The first experiments run on HIDRA started in early 2016 in the low field region. Now, HIDRA is also capable of running in the high field zone, allowing for more interesting experiments and meaningful outcomes. Here, we present some of the initial results coming from the machine.

Experimental Characterization of Thermo-electric Driven Liquid Lithium Flow in Narrow Trenches for Magnetic Confinement Fusion

NASA Astrophysics Data System (ADS)

Xu, Wenyu; Christenson, Michael; Fiflis, Peter; Curreli, Davide; Andruczyk, Daniel; Ruzic, David

2013-10-01

The application of liquid metal, especially liquid lithium has become an important topic for plasma facing component (PFC) design. A liquid PFC can effectively eliminate the erosion and thermal stress problems compared to the solid PFC while transferring heat and prolong the lifetime limit of the PFCs. A liquid lithium surface can also suppress the hydrogen isotopes recycling and getter the impurities in fusion reactors. The Lithium/metal infused trench (LiMIT) concept successfully proved that the thermoelectric effect can be utilized to drive liquid lithium flow within horizontally placed metallic open trenches in transverse magnetic field. A limiter based on this concept was tested in HT-7 and gave out positive results. However a broader application of this concept may require the trench be tilted or even placed vertically, for which strong capillary force caused by narrow trenches may be the solution. A new LiMIT design with very narrow trenches have been manufactured and tested in University of Illinois and related results will be presented. Based on this idea new limiters are designed for EAST and LTX and scheduled experiments on both devices will be discussed. This project is supported by DOE/ALPS contract: DEFG02- 99ER54515.

Plasma facing materials performance under ITER-relevant mitigated disruption photonic heat loads

NASA Astrophysics Data System (ADS)

Klimov, N. S.; Putrik, A. B.; Linke, J.; Pitts, R. A.; Zhitlukhin, A. M.; Kuprianov, I. B.; Spitsyn, A. V.; Ogorodnikova, O. V.; Podkovyrov, V. L.; Muzichenko, A. D.; Ivanov, B. V.; Sergeecheva, Ya. V.; Lesina, I. G.; Kovalenko, D. V.; Barsuk, V. A.; Danilina, N. A.; Bazylev, B. N.; Giniyatulin, R. N.

2015-08-01

PFMs (Plasma-facing materials: ITER grade stainless steel, beryllium, and ferritic-martensitic steels) as well as deposited erosion products of PFCs (Be-like, tungsten, and carbon based) were tested in QSPA under photonic heat loads relevant to those expected from photon radiation during disruptions mitigated by massive gas injection in ITER. Repeated pulses slightly above the melting threshold on the bulk materials eventually lead to a regular, "corrugated" surface, with hills and valleys spaced by 0.2-2 mm. The results indicate that hill growth (growth rate of ∼1 μm per pulse) and sample thinning in the valleys is a result of melt-layer redistribution. The measurements on the 316L(N)-IG indicate that the amount of tritium absorbed by the sample from the gas phase significantly increases with pulse number as well as the modified layer thickness. Repeated pulses significantly below the melting threshold on the deposited erosion products lead to a decrease of hydrogen isotopes trapped during the deposition of the eroded material.

Perfluorinated compounds in human blood, water, edible freshwater fish, and seafood in China: daily intake and regional differences in human exposures.

PubMed

Zhang, Tao; Sun, Hongwen; Lin, Yan; Wang, Lei; Zhang, Xianzhong; Liu, Ya; Geng, Xia; Zhao, Lijie; Li, Fasong; Kannan, Kurunthachalam

2011-10-26

Despite the growing public interest in perfluorinated compounds (PFCs), very few studies have reported the sources and pathways of human exposure to these compounds in China. In this study, concentrations of 10 PFCs were measured in human blood, water (tap water and surface water), freshwater fish, and seafood samples collected from China. On the basis of the data, we calculated daily intakes of PFCs, regional differences in human exposures, and potential risks associated with ingestion of PFCs from diet, drinking water, and indoor dust for the Chinese population. Perfluorooctane sulfonate (PFOS) was the most predominant PFC found with a mean concentration of 12.5 ng/mL in human blood from Tianjin and 0.92 ng/g wet wt in freshwater fish and seafood; perfluorooctanoic acid (PFOA) was the major PFC found in drinking water at a concentration range of 0.10 to 0.92 ng/L. The estimated daily intake of PFOS and PFOA via fish and seafood consumption (EDI(fish&seafood)) ranged from 0.10 to 2.51 and 0.13 to 0.38 ng/kg bw/day, respectively, for different age groups (i.e., toddlers, adolescents and children, and adults) from selected locations (i.e., Tianjin, Nanchang, Wuhan, and Shenyang). The EDI(fish&seafood) of PFCs decreased (p < 0.05) with age. The estimated daily intake of PFOS and PFOA via drinking water consumption (EDI(drinking water)) ranged from 0.006 to 0.014 and 0.010 to 0.159 ng/kg bw/day, respectively. Comparison of EDI(fish&seafood) and EDI(drinking water) values with those of the modeled total dietary intake (TDI) of PFCs by adults from Tianjin, Nanchang, Wuhan, and Shenyang showed that contributions of fish and seafood to TDI of PFOS varied depending on the location. Fish and seafood accounted for 7%, 24%, 80%, and 84% of PFOS intake in Nanchang, Shenyang, Wuhan, and Tianjin, respectively, suggesting regional differences in human exposure to PFOS. Drinking water was a minor source of PFOS (<1%) exposure in adults from all the study locations.

Serum metabolome biomarkers associate low-level environmental perfluorinated compound exposure with oxidative /nitrosative stress in humans.

PubMed

Wang, Xiaofei; Liu, Liangpo; Zhang, Weibing; Zhang, Jie; Du, Xiaoyan; Huang, Qingyu; Tian, Meiping; Shen, Heqing

2017-10-01

Previous in vivo and in vitro studies have linked perfluorinated compound (PFC) exposure with metabolic interruption, but the inter-species difference and high treatment doses usually make the results difficult to be extrapolated to humans directly. The best strategy for identifying the metabolic interruption may be to establish the direct correlations between monitored PFCs data and metabolic data on human samples. In this study, serum metabolome data and PFC concentrations were acquired for a Chinese adult male cohort. The most abundant PFCs are PFOA and PFOS with concentration medians 7.56 and 12.78 nM, respectively; in together they count around 81.6% of the total PFCs. PFC concentration-related serum metabolic profile changes and the related metabolic biomarkers were explored by using partial least squares-discriminant analysis (PLS-DA). Respectively taking PFOS, PFOA and total PFC as the classifiers, serum metabolome can be differentiated between the lowest dose group (1st quartile PFCs) and the highest PFC dose group (4th quartile PFCs). Ten potential PFC biomarkers were identified, mainly involving in pollutant detoxification, antioxidation and nitric oxide (NO) signal pathways. These suggested that low-level environmental PFC exposure has significantly adverse impacts on glutathione (GSH) cycle, Krebs cycle, nitric oxide (NO) generation and purine oxidation in humans. To the best of our knowledge, this is the first report investigating the association of environmental PFC exposure with human serum metabolome alteration. Given the important biological functions of the identified biomarkers, we suggest that PFC could increase the metabolism syndromes risk including diabetes and cardiovascular diseases. Copyright © 2017 Elsevier Ltd. All rights reserved.

Specific profiles of perfluorinated compounds in surface and drinking waters and accumulation in mussels, fish, and dolphins from southeastern Brazil.

PubMed

Quinete, Natalia; Wu, Qian; Zhang, Tao; Yun, Se Hun; Moreira, Isabel; Kannan, Kurunthachalam

2009-10-01

Despite the concern over widespread distribution of perfluorinated compounds (PFCs) even in sparsely populated regions of the world, few studies have reported their occurrence in South America. In this study, PFCs were measured in Rio de Janeiro State in southeast Brazil: in drinking water from various districts in the State, in river water and tucuxi dolphins from the Paraiba do Sul River, several species of fish from the State, and mussels from Guanabara Bay. Liver, kidney, and muscle from fishes were analyzed to enable an understanding of the tissue distribution of PFCs. PFOS, PFOA, and PFHxS were detected in all drinking water samples in concentration ranges of 0.58-6.70, 0.35-2.82, and 0.15-1.00 ng L(-1), respectively. The profiles of PFCs in drinking water from Brazil (with PFOS concentrations comparable to or higher than those of PFOA) were different from the profiles that have been reported for other countries. In fish, concentrations of PFOS were, in general, higher in liver than in muscle. Concentrations of PFOA in livers of fish were similar to or lower than fish muscle tissue concentrations. PFOS and PFOA were found in brown mussels from Guanabara Bay. Bioconcentration factors (BCFs) of PFOA calculated for mussels were higher than the BCFs calculated for fishes. Elevated concentrations of PFUnDA (mean: 109+/-17.4 ng g(-1) wet weight) were found in mussels from certain locations within Guanabara Bay. Although PFCs were detected in all types of samples analyzed, the concentrations were generally lower than the concentrations reported for Japan and the USA.

Sorption of Perfluorinated Compounds onto different types of sewage sludge and assessment of its importance during wastewater treatment.

PubMed

Arvaniti, Olga S; Andersen, Henrik R; Thomaidis, Nikolaos S; Stasinakis, Athanasios S

2014-09-01

The distribution coefficient (Kd) and the organic carbon distribution coefficient (KOC) were determined for four Perfluorinated Compounds (PFCs) to three different types of sludge taken from a conventional Sewage Treatment Plant (STP). Batch experiments were performed in six different environmental relevant concentrations (200ngL(-1)to 5μgL(-1)) containing 1gL(-1) sludge. Kd values ranged from 330 to 6015, 329 to 17432 and 162 to 11770Lkg(-1) for primary, secondary and digested sludge, respectively. The effects of solution's pH, ionic strength and cation types on PFCs sorption were also evaluated. Sorption capacities of PFCs significantly decreased with increased pH values from 6 to 8. Furthermore, the divalent cation (Ca(2+)) enhanced PFCs sorption to a higher degree in comparison with the monovalent cation (Na(+)) at the same ionic strength. The obtained Kd values were applied to estimate the sorbed fractions of each PFC in different stages of a typical STP and to calculate their removal through treated wastewater and sludge. In primary settling tank, the predicted sorbed fractions ranged from 3% for Perfluorooctanoic Acid (PFOA) to 55% for Perfluoroundecanoic acid (PFUdA), while in activated sludge tank and anaerobic digester sorption was more than 50% for all target compounds. Almost 86% of initial PFOA load is expected to be detected in treated wastewater; while Perfluorodecanoic acid (PFDA), PFUdA and Perfluorooctanesulfonate (PFOS) can be significantly removed (>49%) via sorption to primary and excess secondary sludge. In anaerobic digester, the major part (>76%) of target PFCs is expected to be sorbed to sludge, while almost 3% of initial PFOA load will be detected in sludge leachates. Copyright © 2014 Elsevier Ltd. All rights reserved.

Fluoroscopy-assisted vs fluoroless endoscopic ultrasound-guided transmural drainage of pancreatic fluid collections: A comparative study.

PubMed

Consiglieri, Claudia F; Gornals, Joan B; Busquets, Juli; Peláez, Nuria; Secanella, Lluis; De-La-Hera, Meritxell; Sanzol, Resurrección; Fabregat, Joan; Castellote, José

2018-01-01

The need for fluoroscopy guidance in patients undergoing endoscopic ultrasound-guided transmural drainage (EUS-TMD) of peripancreatic fluid collections (PFCs) remains unclear. The aim of this study was to compare general outcomes of EUS-TMD of PFCs under fluoroscopy (F) vs fluoroless (FL). This is a comparative study with a retrospective analysis of a prospective and consecutive inclusion database at a tertiary centre, from 2009 to 2015. All patients were symptomatic pseudocyst (PSC) and walled-off pancreatic necrosis (WON). Two groups were assigned depending on availability of fluoroscopy. The groups were heterogeneous in terms of their demographic characteristics, PFCs and procedure. The main outcome measures included technical and clinical success, incidences, adverse events (AEs), and follow-up. Fifty EUS-TMD of PFCs from 86 EUS-guided drainages were included during the study period. Group F included 26 procedures, PSC 69.2%, WON 30.8%, metal stents 61.5% (46.1% lumen-apposing stent) and plastic stents 38.5%. Group FL included 24 procedures, PSC 37.5%, WON 62.5%, and metal stents 95.8% (lumen-apposing stents). Technical success was 100% in both groups, and clinical success was similar (F 88.5%, FL 87.5%). Technical incidences and intra-procedure AEs were only described in group F (7.6% and 11.5%, respectively) and none in group FL. Procedure time was less in group FL (8min, p=0.0341). Fluoroless in the EUS-TMD of PFCs does not involve more technical incidences or intra-procedure AEs. Technical and clinical success was similar in the two groups. Copyright © 2017 Elsevier España, S.L.U. All rights reserved.

The 747 primary flight control systems reliability and maintenance study

NASA Technical Reports Server (NTRS)

1979-01-01

The major operational characteristics of the 747 Primary Flight Control Systems (PFCS) are described. Results of reliability analysis for separate control functions are presented. The analysis makes use of a NASA computer program which calculates reliability of redundant systems. Costs for maintaining the 747 PFCS in airline service are assessed. The reliabilities and cost will provide a baseline for use in trade studies of future flight control system design.

Design of ultrasonically-activatable nanoparticles using low boiling point perfluorocarbons.

PubMed

Sheeran, Paul S; Luois, Samantha H; Mullin, Lee B; Matsunaga, Terry O; Dayton, Paul A

2012-04-01

Recently, an interest has developed in designing biomaterials for medical ultrasonics that can provide the acoustic activity of microbubbles, but with improved stability in vivo and a smaller size distribution for extravascular interrogation. One proposed alternative is the phase-change contrast agent. Phase-change contrast agents (PCCAs) consist of perfluorocarbons (PFCs) that are initially in liquid form, but can then be vaporized with acoustic energy. Crucial parameters for PCCAs include their sensitivity to acoustic energy, their size distribution, and their stability, and this manuscript provides insight into the custom design of PCCAs for balancing these parameters. Specifically, the relationship between size, thermal stability and sensitivity to ultrasound as a function of PFC boiling point and ambient temperature is illustrated. Emulsion stability and sensitivity can be 'tuned' by mixing PFCs in the gaseous state prior to condensation. Novel observations illustrate that stable droplets can be generated from PFCs with extremely low boiling points, such as octafluoropropane (b.p. -36.7 °C), which can be vaporized with acoustic parameters lower than previously observed. Results demonstrate the potential for low boiling point PFCs as a useful new class of compounds for activatable agents, which can be tailored to the desired application. Copyright © 2012 Elsevier Ltd. All rights reserved.

Pilot Scale Application of a Method for the Analysis of ...

EPA Pesticide Factsheets

A growing number of studies now indicate that perfluorinated compounds (PFCs) are globally distributed in the environment. Their widespread distribution and presence in remote locations has led to questions about the importance of atmospheric and oceanic transport. Describing their distribution in surface soils is also an essential but neglected element in developing a comprehensive understanding of their occurrence in the environment. Soils are the critical link between global atmospheric and hydrologic processes where both local and distant contaminants can accumulate and be released into aquatic and terrestrial communities. Because PFC concentrations in soils will influence ground and surface water, wildlife, and crops, methods to accurately measure PFCs in soil are clearly needed. To help answer this need, we developed a method for the analysis of nine perfluorinated carboxylic acids and four perfluorinated sulfonic acids in soil. Samples from six nations (n = 10 per nation) were analyzed by LC-MS/MS to demonstrate the method performance parameters and to make preliminary observations about the occurrence of the PFCs in soils in different parts of the world. The resulting method shows acceptable performance characteristics for the target compounds in most soils while documenting the widespread occurrence of PFCs in surface soils The National Exposure Research Laboratory′s (NERL) Human Exposure and Atmospheric Sciences Division (HEASD) conducts research in

Perfluorooctanesulfonate and related fluorochemicals in the Amur tiger (Panthera tigris altaica) from China.

PubMed

Li, Xuemei; Yeung, Leo W Y; Taniyasu, Sachi; Li, Ming; Zhang, Hongxia; Liu, Dan; Lam, Paul K S; Yamashita, Nobuyoshi; Dai, Jiayin

2008-10-01

Perfluorinated compounds (PFCs) are used in a variety of industrial applications. We tested the hypothesis that, in Amur tigers (Panthera tigris altaica), captivity in industrialized areas increases PFC levels, potentially presenting a health risk to these animals. Serum samples were collected from 100 tigers from industrialized or nonindustrialized regions in China with nonpoint sources of PFCs. Mean concentrations of PFCs in these samples ranged from 1.57 +/- 0.83 ng/mL in nonindustrial Hailin to 4.31 +/- 2.90 ng/mL in industrial Beijing. PFC concentrations were significantly higher in tigers from the industrial city of Harbin than those from Hailin (p < 0.05). Perfluorooctanesulfonate (PFOS) was the most abundant PFC in all tigers and increased with age, regardless of industrial/ nonindustrial background (p < 0.01). However, PFOS concentrations were 2-4 orders of magnitude less than the current no-observed-effect level. In addition, overall PFC levels in Amur tigers were low compared with various species living in other countries, consistent with the relatively short history of PFC use in China. These results are consistent with the hypothesis that captivity in industrialized areas increases PFC levels in Amurtigers. They also suggestthat PFC accumulation will persist, and even increase, with continued use of PFCs in China.

Treatment of Perfluorinated Compounds and Nitroaromatics by Photocatalysis in the Presence of Ultraviolet and Solar Light

DTIC Science & Technology

2014-03-27

conductor etching, aqueous film forming foams, and thermally stable lubricants ( Lindstrom et al., 2011; Vecitis et al., 2009). PFCs’ unique...2007; Lindstrom et al., 2011). According to Appleman et al. (2013), certain PFCs are found in the serum of virtually all U.S. residents and have...perfluorinated tail, when properly oriented, make PFCs ideal surfactants and dispersants such as firefighting foams ( Lindstrom et al., 2011) 22

Effect of whole-body irradiation of mice on the number of background plaque-forming cells

DOE Office of Scientific and Technical Information (OSTI.GOV)

Anderson, R.E.; Lefkovits, I.; Soeederberg, A.

1983-08-01

Mice were exposed in whole-body fashion to several doses of radiation and killed at various times thereafter for a determination of the number of background plaque-forming cells (PFCs) as assayed on either sheep erythrocytes or bromelain-treated autologous mouse erythrocytes. Increased numbers of both types of PFC were found in the irradiated groups. These increases were dependent on radiation dose and time after exposure. They did not appear to be caused by a disruption of normal lymphocyte traffic or a switch in immunoglobulin isotype. An increased number of PFCs on bromelain-treated mouse RBCs but not on sheep RBCs were found inmore » irradiated congenitally athymic nude mice. On the basis of this and related observations, background PFCs on bromelain-treated mouse RBCs and on sheep RBCs appear to fall under different forms of homeostatic control.« less

Mapping Forest Fuels through Vegetation Phenology: The Role of Coarse-Resolution Satellite Time-Series

PubMed Central

Bajocco, Sofia; Dragoz, Eleni; Gitas, Ioannis; Smiraglia, Daniela; Salvati, Luca; Ricotta, Carlo

2015-01-01

Traditionally fuel maps are built in terms of ‘fuel types’, thus considering the structural characteristics of vegetation only. The aim of this work is to derive a phenological fuel map based on the functional attributes of coarse-scale vegetation phenology, such as seasonality and productivity. MODIS NDVI 250m images of Sardinia (Italy), a large Mediterranean island with high frequency of fire incidence, were acquired for the period 2000–2012 to construct a mean annual NDVI profile of the vegetation at the pixel-level. Next, the following procedure was used to develop the phenological fuel map: (i) image segmentation on the Fourier components of the NDVI profiles to identify phenologically homogeneous landscape units, (ii) cluster analysis of the phenological units and post-hoc analysis of the fire-proneness of the phenological fuel classes (PFCs) obtained, (iii) environmental characterization (in terms of land cover and climate) of the PFCs. Our results showed the ability of coarse-resolution satellite time-series to characterize the fire-proneness of Sardinia with an adequate level of accuracy. The remotely sensed phenological framework presented may represent a suitable basis for the development of fire distribution prediction models, coarse-scale fuel maps and for various biogeographic studies. PMID:25822505

Addition of perfluorocarbons to alginate hydrogels significantly impacts molecular transport and fracture stress.

PubMed

White, Joseph C; Stoppel, Whitney L; Roberts, Susan C; Bhatia, Surita R

2013-02-01

Perfluorocarbons (PFCs) are used in biomaterial formulations to increase oxygen (O(2) ) tension and create a homogeneous O(2) environment in three-dimensional tissue constructs. It is unclear how PFCs affect mechanical and transport properties of the scaffold, which are critical for robustness, intracellular signaling, protein transport, and overall device efficacy. In this study, we investigate composite alginate hydrogels containing a perfluorooctyl bromide (PFOB) emulsion stabilized with Pluronic(®) F68 (F68). We demonstrate that PFC addition significantly affects biomaterial properties and performance. Solution and hydrogel mechanical properties and transport of representative hydrophilic (riboflavin), hydrophobic (methyl and ethyl paraben), and protein (bovine serum albumin, BSA) solutes were compared in alginate/F68 composite hydrogels with or without PFOB. Our results indicate that mechanical properties of the alginate/F68/PFOB hydrogels are not significantly affected under small strains, but a significant decrease fracture stress is observed. The effective diffusivity D(eff) of hydrophobic small molecules decreases with PFOB emulsion addition, yet the D(eff) of hydrophilic small molecules remained unaffected. For BSA, the D(eff) increased and the loading capacity decreased with PFOB emulsion addition. Thus, a trade-off between the desired increased O(2) supply provided by PFCs and the mechanical weakening and change in transport of cellular signals must be carefully considered in the design of biomaterials containing PFCs. Copyright © 2012 Wiley Periodicals, Inc.

Perfluorochemical (PFC) exposure in children: associations with impaired response inhibition.

PubMed

Gump, Brooks B; Wu, Qian; Dumas, Amy K; Kannan, Kurunthachalam

2011-10-01

Perfluorinated chemicals (PFCs) have been used widely in consumer products since the 1950s and are currently found at detectable levels in the blood of humans and animals across the globe. In stark contrast to this widespread exposure to PFCs, there is relatively little research on potential adverse health effects of exposure to these chemicals. We performed this cross-sectional study to determine if specific blood PFC levels are associated with impaired response inhibition in children. Blood levels of 11 PFCs were measured in children (N = 83) and 6 PFCs: perfluorooctane sulfonate (PFOS), perfluorohexane sulfate (PFHxS), perfluorooctanoic acid (PFOA), perfluorononanoic acid (PFNA), perfluorooctanesulfonamide (PFOSA), and perfluorodecanoic acid (PFDA) - were found at detectable levels in most children (87.5% or greater had detectable levels). These levels were analyzed in relation to the differential reinforcement of low rates of responding (DRL) task. This task rewards delays between responses (i.e., longer inter-response times; IRTs) and therefore constitutes a measure of response inhibition. Higher levels of blood PFOS, PFNA, PFDA, PFHxS, and PFOSA were associated with significantly shorter IRTs during the DRL task. The magnitude of these associations was such that IRTs during the task decreased by 29-34% for every 1 SD increase in the corresponding blood PFC. This study suggests an association between PFC exposure and children's impulsivity. Although intriguing, there is a need for further investigation and replication with a larger sample of children.

Polyfluoroalkyl Chemicals and Menopause among Women 20–65 Years of Age (NHANES)

PubMed Central

Hoffman, Kate; Thayer, Kristina A.; Daniels, Julie L.

2013-01-01

Background: Polyfluoroalkyl chemicals (PFCs) such as perfluorooctane sulfonate (PFOS) and perfluorooctanoate (PFOA) have been associated with early menopause. However, previous cross-sectional studies have lacked adequate data to investigate possible reverse causality (i.e., higher serum concentrations due to decreased excretion after menopause). Objectives: We investigated the association between PFOS, PFOA, perfluorononanoate (PFNA), and perfluorohexane sulfonate (PFHxS) and age at natural menopause among women 20–65 years of age in NHANES (National Health and Nutrition Examination Survey). Methods: We used proportional hazard models to estimate hazard ratios (HRs) for the onset of natural menopause as a function of age and serum PFC levels, and to investigate reverse causation by estimating associations between PFC levels and the rate of hysterectomy. We also used multivariable linear regression to determine whether time since menopause predicted serum PFC levels. Results: After adjusting for age at survey, race/ethnicity, education, ever smoking, and parity, women with higher levels of PFCs had earlier menopause than did women with the lowest PFC levels. We observed a monotonic association with PFHxS: The HR was 1.42 (95% CI: 1.08, 1.87) for serum concentrations in tertile 2 versus tertile 1, and 1.70 (95% CI: 1.36, 2.12) for tertile 3 versus tertile 1. We also found evidence of reverse causation: PFCs were positively associated with rate of hysterectomy, and time since natural menopause was positively associated with serum PFCs. Conclusions: Our findings suggest a positive association between PFCs and menopause; however, at least part of the association may be due to reverse causation. Regardless of underlying cause, women appear to have higher PFC concentrations after menopause. Citation: Taylor KW, Hoffman K, Thayer KA, Daniels JL. 2014. Polyfluoroalkyl chemicals and menopause among women 20–65 years of age (NHANES). Environ Health Perspect 122:145–150; http://dx.doi.org/10.1289/ehp.1306707 PMID:24280566

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gorrochategui, Eva; Pérez-Albaladejo, Elisabet; Casas, Josefina

The cytotoxicity of eight perfluorinated chemicals (PFCs), namely, perfluorobutanoic acid (PFBA), perfluorohexanoic acid (PFHxA), perfluorooctanoic acid (PFOA), perfluorononanoic acid (PFNA), perfluorododecanoic acid (PFDoA), perfluorobutanesulfonate (PFBS), perfluorohexanesulfonate (PFHxS) and perfluorooctanesulfonate (PFOS) was assessed in the human placental choriocarcinoma cell line JEG-3. Only the long chain PFCs – PFOS, PFDoA, PFNA, PFOA – showed significant cytotoxicity in JEG-3 cells with EC50 values in the range of 107 to 647 μM. The observed cytotoxicity was to some extent related to a higher uptake of the longer chain PFCs by cells (PFDoA > PFOS ≫ PFNA > PFOA > PFHxA). Moreover, this work evidencesmore » a high potential of PFOS, PFOA and PFBS to act as aromatase inhibitors in placental cells with IC50s in the range of 57–80 μM, the inhibitory effect of PFBS being particularly important despite the rather low uptake of the compound by cells. Finally, exposure of JEG-3 cells to a mixture of the eight PFCs (0.6 μM each) led to a relative increase (up to 3.4-fold) of several lipid classes, including phosphatidylcholines (PCs), plasmalogen PC and lyso plasmalogen PC, which suggests an interference of PFCs with membrane lipids. Overall, this work highlights the ability of the PFC mixture to alter cellular lipid pattern at concentrations well below those that generate toxicity, and the potential of the short chain PFBS, often considered a safe substitute of PFOS, to significantly inhibit aromatase activity in placental cells. - Highlights: • Eight perfluorinated chemicals of different chain lengths have been selected. • Long chain ones – PFOS, PFDoA, PFNA, PFOA – were cytotoxic in placenta cells. • The uptake of long chain perfluorinated chemicals by cells was comparatively higher. • PFOS, PFOA and the short chain PFBS significantly inhibited aromatase activity. • A mixture of perfluorinated chemicals significantly altered placenta cell lipidome.« less

Assessment of removal efficiency of perfluorocompounds (PFCs) in a semiconductor fabrication plant by gas chromatography.

PubMed

Ou Yang, Chang-Feng; Kam, Seak-Hong; Liu, Chia-Hung; Tzou, Jiren; Wang, Jia-Lin

2009-08-01

This study investigated a gas chromatographic (GC) method to assess the destruction or removal efficiency (DRE) of local scrubbers on five perfluorocompounds (PFCs), i.e., SF(6), NF(3), CF(4), C(2)F(6), and C(3)F(8), which are very potent greenhouse gases used in a semiconductor fabrication plant. Air samples taken at inlets and outlets of local scrubbers were analyzed by a self-constructed multi-column GC system equipped with thermal conductivity detection. Three packed columns were integrated into the heart-cut GC system to allow simultaneous analysis of the five target PFCs. The Porapak Q pre-column performs rough separation and cuts eluent groups to two analytical columns for optimal separation. The Molecular Sieve - 5A column separated NF(3), CF(4), and C(3)F(8) and the second Porapak Q separated SF(6) and C(2)F(6). Linearity was greater than 0.995 (R(2)) for the five PFCs, and the reproducibility was about 4% (relative standard deviation) for NF(3), and better than 0.5% for the other four PFCs. DRE for the combustion (CB) and electric-thermal types of local scrubbers was evaluated by taking into account the in-line dilution from air and fuel gases. Both flow and tracer methods were employed to deduce the dilution factors (DFs). For the tracer method, helium was employed as the tracer and injected upstream of the scrubbers and thus mixed with the exhaust gas. With this method, the DFs were determined to be in the range from 4.8 to 5.9 for the CB unit, significantly higher than the value of 3.3 based on the flow method. The DREs for the CB unit for C(3)F(8) were greater than 90% and between 40% and 50% for CF(4).

Micro/nano composited tungsten material and its high thermal loading behavior

NASA Astrophysics Data System (ADS)

Fan, Jinglian; Han, Yong; Li, Pengfei; Sun, Zhiyu; Zhou, Qiang

2014-12-01

Tungsten (W) is considered as promising candidate material for plasma facing components (PFCs) in future fusion reactors attributing to its many excellent properties. Current commercial pure tungsten material in accordance with the ITER specification can well fulfil the performance requirements, however, it has defects such as coarse grains, high ductile-brittle transition temperature (DBTT) and relatively low recrystallization temperature compared with its using temperature, which cannot meet the harsh wall loading requirement of future fusion reactor. Grain refinement has been reported to be effective in improving the thermophysical and mechanical properties of W. In this work, rare earth oxide (Y2O3/La2O3) and carbides (TiC/ZrC) were used as dispersion phases to refine W grains, and micro/nano composite technology with a process of "sol gel - heterogeneous precipitation - spray drying - hydrogen reduction - ordinary consolidation sintering" was invented to introduce these second-phase particles uniformly dispersed into W grains and grain-boundaries. Via this technology, fine-grain W materials with near-full density and relatively high mechanical properties compared with traditional pure W material were manufactured. Preliminary transient high-heat flux tests were performed to evaluate the thermal response under plasma disruption conditions, and the results show that the W materials prepared by micro/nano composite technology can endure high-heat flux of 200 MW/m2 (5 ms).

Determination of perfluorocompounds in popcorn packaging by pressurised liquid extraction and ultra-performance liquid chromatography-tandem mass spectrometry.

PubMed

Martínez-Moral, María Pilar; Tena, María Teresa

2012-11-15

The development and characterisation of a method based on reverse-phase ultra-performance liquid chromatography (UPLC) coupled to a quadrupole-time of flight mass spectrometer (Q-TOF-MS) with negative electrospray ionisation (ESI) to determine perfluorinated compounds (PFCs) in packaging is presented in this paper. Analytes were quantitatively recovered from packaging with methanol in only one PLE cycle of 6 min at 100 °C. The UPLC allowed the successful separation of the studied PFCs in less than 4 min. The whole method presented good precision, with RSDs below 8%, LODs from 0.6 to 16 ng g(-1); and excellent recovery values, around 100% in all cases, were achieved. The PLE-UPLC-MS method was applied to the analysis of popcorn packaging for microwave cooking. Besides the most commonly studied PFCs: PFOA and PFOS, the presence of other perfluorocarboxylic acids (PFCAs) in popcorn packaging is evidenced in this work. Copyright © 2012 Elsevier B.V. All rights reserved.

Assessment of perfluorooctanoic acid and perfluorooctane sulfonate in surface water - Tamil Nadu, India.

PubMed

Sunantha, Ganesan; Vasudevan, Namasivayam

2016-08-15

As an emerging class of environmentally persistent organic pollutants, perfluorinated compounds (PFCs), particularly perfluorooctanoic acid (PFOA) and perfluorooctane sulfonate (PFOS); have been universally found in the environment. Wastewater and untreated effluents are likely the major causes for the accumulation of PFCs in surface water. There are very few reports on the contamination of PFCs in the developing countries, particularly in India. This study reports the quantitative analysis of PFOA and PFOS in Noyyal, Cauvery, and also lakes in and around Chennai, using Ultra-Fast liquid chromatograph. The concentration of PFOA and PFOS ranged from 4 to 93ng/L and 3 to 29ng/L, respectively. The concentration of PFOS was below detectable limit in Cauvery River. A reliable concentration of PFOA was recorded at all sites of River Cauvery (5ng/L). The present study could be useful for the assessment of future monitoring programs of PFOA and PFOS in the surface water. Copyright © 2016 Elsevier Ltd. All rights reserved.

International Space Station Active Thermal Control Sub-System On-Orbit Pump Performance and Reliability Using Liquid Ammonia as a Coolant

NASA Technical Reports Server (NTRS)

Morton, Richard D.; Jurick, Matthew; Roman, Ruben; Adamson, Gary; Bui, Chinh T.; Laliberte, Yvon J.

2011-01-01

The International Space Station (ISS) contains two Active Thermal Control Sub-systems (ATCS) that function by using a liquid ammonia cooling system collecting waste heat and rejecting it using radiators. These subsystems consist of a number of heat exchangers, cold plates, radiators, the Pump and Flow Control Subassembly (PFCS), and the Pump Module (PM), all of which are Orbital Replaceable Units (ORU's). The PFCS provides the motive force to circulate the ammonia coolant in the Photovoltaic Thermal Control Subsystem (PVTCS) and has been in operation since December, 2000. The Pump Module (PM) circulates liquid ammonia coolant within the External Active Thermal Control Subsystem (EATCS) cooling the ISS internal coolant (water) loops collecting waste heat and rejecting it through the ISS radiators. These PM loops have been in operation since December, 2006. This paper will discuss the original reliability analysis approach of the PFCS and Pump Module, comparing them against the current operational performance data for the ISS External Thermal Control Loops.

The impact of semiconductor, electronics and optoelectronic industries on downstream perfluorinated chemical contamination in Taiwanese rivers.

PubMed

Lin, Angela Yu-Chen; Panchangam, Sri Chandana; Lo, Chao-Chun

2009-04-01

This study provides the first evidence on the influence of the semiconductor and electronics industries on perfluorinated chemicals (PFCs) contamination in receiving rivers. We have quantified ten PFCs, including perfluoroalkyl sulfonates (PFASs: PFBS, PFHxS, PFOS) and perfluoroalkyl carboxylates (PFCAs: PFHxA, PFHpA, PFOA, PFNA, PFDA, PFUnA, PFDoA) in semiconductor, electronic, and optoelectronic industrial wastewaters and their receiving water bodies (Taiwan's Keya, Touchien, and Xiaoli rivers). PFOS was found to be the major constituent in semiconductor wastewaters (up to 0.13 mg/L). However, different PFC distributions were found in electronics plant wastewaters; PFOA was the most significant PFC, contributing on average 72% to the effluent water samples, followed by PFOS (16%) and PFDA (9%). The distribution of PFCs in the receiving rivers was greatly impacted by industrial sources. PFOS, PFOA and PFDA were predominant and prevalent in all the river samples, with PFOS detected at the highest concentrations (up to 5.4 microg/L).

Nano-Sized Cyclodextrin-Based Molecularly Imprinted Polymer Adsorbents for Perfluorinated Compounds—A Mini-Review

PubMed Central

Karoyo, Abdalla H.; Wilson, Lee D.

2015-01-01

Recent efforts have been directed towards the design of efficient and contaminant selective remediation technology for the removal of perfluorinated compounds (PFCs) from soils, sediments, and aquatic environments. While there is a general consensus on adsorption-based processes as the most suitable methodology for the removal of PFCs from aquatic environments, challenges exist regarding the optimal materials design of sorbents for selective uptake of PFCs. This article reviews the sorptive uptake of PFCs using cyclodextrin (CD)-based polymer adsorbents with nano- to micron-sized structural attributes. The relationship between synthesis of adsorbent materials and their structure relate to the overall sorption properties. Hence, the adsorptive uptake properties of CD-based molecularly imprinted polymers (CD-MIPs) are reviewed and compared with conventional MIPs. Further comparison is made with non-imprinted polymers (NIPs) that are based on cross-linking of pre-polymer units such as chitosan with epichlorohydrin in the absence of a molecular template. In general, MIPs offer the advantage of selectivity, chemical tunability, high stability and mechanical strength, ease of regeneration, and overall lower cost compared to NIPs. In particular, CD-MIPs offer the added advantage of possessing multiple binding sites with unique physicochemical properties such as tunable surface properties and morphology that may vary considerably. This mini-review provides a rationale for the design of unique polymer adsorbent materials that employ an intrinsic porogen via incorporation of a macrocyclic compound in the polymer framework to afford adsorbent materials with tunable physicochemical properties and unique nanostructure properties. PMID:28347047

The relationships between sixteen perfluorinated compound concentrations in blood serum and food, and other parameters, in the general population of South Korea with proportionate stratified sampling method.

PubMed

Kim, Hee-Young; Kim, Seung-Kyu; Kang, Dong-Mug; Hwang, Yong-Sik; Oh, Jeong-Eun

2014-02-01

Serum samples were collected from volunteers of various ages and both genders using a proportionate stratified sampling method, to assess the exposure of the general population in Busan, South Korea to perfluorinated compounds (PFCs). 16 PFCs were investigated in serum samples from 306 adults (124 males and 182 females) and one day composite diet samples (breakfast, lunch, and dinner) from 20 of the serum donors, to investigate the relationship between food and serum PFC concentrations. Perfluorooctanoic acid and perfluorooctanesulfonic acid were the dominant PFCs in the serum samples, with mean concentrations of 8.4 and 13 ng/mL, respectively. Perfluorotridecanoic acid was the dominant PFC in the composite food samples, ranging from

Development of an analytical strategy based on liquid chromatography-high resolution mass spectrometry for measuring perfluorinated compounds in human breast milk: application to the generation of preliminary data regarding perinatal exposure in France.

PubMed

Kadar, Hanane; Veyrand, Bruno; Barbarossa, Andrea; Pagliuca, Giampiero; Legrand, Arnaud; Bosher, Cécile; Boquien, Clair-Yves; Durand, Sophie; Monteau, Fabrice; Antignac, Jean-Philippe; Le Bizec, Bruno

2011-10-01

Perfluorinated compounds (PFCs) are man-made chemicals for which endocrine disrupting properties and related possible side effects on human health have been reported, particularly in the case of an exposure during the early stages of development, (notably the perinatal period). Existing analytical methods dedicated to PFCs monitoring in food and/or human fluids are currently based on liquid chromatography coupled to tandem mass spectrometry, and were recently demonstrated to present some limitations in terms of sensitivity and/or specificity. An alternative strategy dedicated to the analysis of fourteen PFCs in human breast milk was proposed, based on an effective sample preparation followed by a liquid chromatography coupled to high resolution mass spectrometry measurement (LC-HRMS). This methodology confirmed the high interest for HRMS after negative ionization for such halogenated substances, and finally permitted to reach detection limits around the pg mL(-1) range with an outstanding signal specificity compared to LC-MS/MS. The proposed method was applied to a first set of 30 breast milk samples from French women. The main PFCs detected in all these samples were PFOS and PFOA with respective median values of 74 (range from 24 to 171) and 57 (range from 18 to 102) pg mL(-1), respectively. These exposure data appeared in the same range as other reported values for European countries. Copyright © 2011 Elsevier Ltd. All rights reserved.

Contamination by perfluorinated compounds in water near waste recycling and disposal sites in Vietnam.

PubMed

Kim, Joon-Woo; Tue, Nguyen Minh; Isobe, Tomohiko; Misaki, Kentaro; Takahashi, Shin; Viet, Pham Hung; Tanabe, Shinsuke

2013-04-01

There are very few reports on the contamination by perfluorinated chemicals (PFCs) in the environment of developing countries, especially regarding their emission from waste recycling and disposal sites. This is the first study on the occurrence of a wide range of PFCs (17 compounds) in ambient water in Vietnam, including samples collected from a municipal dumping site (MD), an e-waste recycling site (ER), a battery recycling site (BR) and a rural control site. The highest PFC concentration was found in a leachate sample from MD (360 ng/L). The PFC concentrations in ER and BR (mean, 57 and 16 ng/L, respectively) were also significantly higher than those detected in the rural control site (mean, 9.4 ng/L), suggesting that municipal solid waste and waste electrical and electronic equipment are potential contamination sources of PFCs in Vietnam. In general, the most abundant PFCs were perfluorooctanoic acid (PFOA), perfluorononanoic acid (PFNA), and perfluoroundecanoic acid (PFUDA; <1.4-100, <1.2-100, and <0.5-20 ng/L, respectively). Interestingly, there were specific PFC profiles: perfluoroheptanoic acid and perfluorohexanoic acid (88 and 77 ng/L, respectively) were almost as abundant as PFOA in MD leachate (100 ng/L), whereas PFNA was prevalent in ER and BR (mean, 17 and 6.2 ng/L, respectively) and PFUDA was the most abundant in municipal wastewater (mean, 5.6 ng/L), indicating differences in PFC contents in different waste materials.

Perfluorochemical (PFC) Exposure in Children: Associations with Impaired Response Inhibition

PubMed Central

Gump, Brooks B.; Wu, Qian; Dumas, Amy K.; Kannan, Kurunthachalam

2011-01-01

Background Perfluorinated chemicals (PFCs) have been used widely in consumer products since the 1950s and are currently found at detectable levels in the blood of humans and animals across the globe. In stark contrast to this widespread exposure to PFCs, there is relatively little research on potential adverse health effects of exposure to these chemicals. Objectives We performed this cross-sectional study to determine if specific blood PFC levels are associated with impaired response inhibition in children. Methods Blood levels of 11 PFCs were measured in children (N = 83) and 6 PFCs: perfluorooctane sulfonate (PFOS), perfluorohexane sulfate (PFHxS), perfluorooctanoic acid (PFOA), perfluorononanoic acid (PFNA), perfluorooctanesulfonamide (PFOSA), and perfluorodecanoic acid (PFDA) – were found at detectable levels in most children (87.5% or greater had detectable levels). These levels were analyzed in relation to the differential reinforcement of low rates of responding (DRL) task. This task rewards delays between responses (i.e., longer inter-response times; IRTs) and therefore constitutes a measure of response inhibition. Results Higher levels of blood PFOS, PFNA, PFDA, PFHxS, and PFOSA were associated with significantly shorter IRTs during the DRL task. The magnitude of these associations was such that IRTs during the task decreased by 29–34% for every 1 SD increase in the corresponding blood PFC. Conclusions This study suggests an association between PFC exposure and children’s impulsivity. Although intriguing, there is a need for further investigation and replication with a larger sample of children. PMID:21682250

Evaluating non-equilibrium solute transport in small soil columns

NASA Astrophysics Data System (ADS)

Kamra, S. K.; Lennartz, B.; Van Genuchten, M. Th; Widmoser, P.

2001-04-01

Displacement studies on leaching of bromide and two pesticides (atrazine and isoproturon) were conducted under unsaturated steady state flow conditions in 24 small undisturbed soil columns (5.7 cm in diameter and 10 cm long) each collected from two sites differing in soil structure and organic carbon content in North Germany. There were large and irregular variabilities in the characteristics of both soils, as well as in the shapes of breakthrough curves (BTCs) of different columns, including some with early breakthrough and increased tailing, qualitatively indicating the presence of preferential flow. It was estimated that one preferential flow column (PFC) at site A, and four at site B, contributed, respectively to 11% and 58% of the accumulated leached fraction and to more than 80% of the maximum observed standard deviation (SD) in the field-scale concentration and mass flux of pesticides at two sites. The bromide BTCs of two sites were analyzed with the equilibrium convection-dispersion equation (CDE) and a non-equilibrium two-region/mobile-immobile model. Transport parameters of these models for individual BTCs were determined using a curve fitting program, CXTFIT, and by the time moment method. For the CDE based equilibrium model, the mean values of retardation factor, R, considered separately for all columns, PFCs or non-preferential flow columns (NPFCs) were comparable for the two methods; significant differences were observed in the values of dispersion coefficients of two sites using the two estimation methods. It was inferred from the estimated parameters of non-equilibrium model that 5-12% of water at site A, and 12% at site B, was immobile during displacement in NPFCs. The corresponding values for PFCs of two sites were much larger, ranging from 25% to 51% by CXTFIT and from 24% to 72% by the moment method, suggesting the role of certain mechanisms other than immobile water in higher degrees of non-equilibrium in these columns. Peclet numbers in PFCs of both sites were consistently smaller than five, indicating the inadequacy of the non-equilibrium model to incorporate the effect of all forms of non-equilibrium in PFCs. Overall, the BTCs of individual NPFCs, PFCs and of field average concentration at the two sites were better reproduced with parameters obtained from CXTFIT than by the moment method. The moment method failed to capture the peak concentrations in PFCs, but tended to describe the desorption and tail branches of BTCs better than the curve fitting approach.

Infant exposure of perfluorinated compounds: levels in breast milk and commercial baby food.

PubMed

Llorca, Marta; Farré, Marinella; Picó, Yolanda; Teijón, Marisa Lopez; Alvarez, Juan G; Barceló, Damià

2010-08-01

In this study, an analytical method to determine six perfluorinated compounds (PFCs) based on alkaline digestion and solid phase extraction (SPE) followed by liquid chromatography-quadrupole-linear ion trap mass spectrometry (LC-QqLIT-MS) was validated for the analysis of human breast milk, milk infant formulas and cereals baby food. The average recoveries of the different matrices were in general higher than 70% with a relative standard deviation (RSD) lower than 21% and method limits of detection (MLOD) ranging from 1.2 to 362 ng/L for the different compounds and matrices. The method was applied to investigate the occurrence of PFCs in 20 samples of human breast milk, and 5 samples of infant formulas and cereal baby food (3 brands of commercial milk infant formulas and 2 brands of cereals baby food). Breast milk samples were collected in 2008 from donors living in Barcelona city (Spain) on the 40 days postpartum. Perfluorooctanesulfonate (PFOS) and perfluoro-7-methyloctanoic acid (i,p-PFNA) were predominant being present in the 95% of breast milk samples. Perfluorooctanoic acid (PFOA) was quantified in 8 of the 20 breast milk samples at concentrations in the range of 21-907 ng/L. Commercial formulas and food were purchased also in 2009 from a retail store. The six PFCs were detected in all brands of milk infant formulas and cereals baby food analyzed, being perfluorodecanoic acid (PFDA), PFOS, PFOA and i,p-PFNA the compounds detected in higher concentrations (up to 1289 ng/kg). PFCs presence can be associated to possible migration from packaging and containers during production processes. Finally, based on estimated body weight and newborn intake, PFOS and PFOA daily intakes and risk indexes (RI) were estimated for the firsts 6 month of life. We found that ingestion rates of PFOS and PFOA, with exception of one breast milk sample did not exceed the tolerable daily intake (TDI) recommended by the EFSA. However, more research is needed in order to assess possible risk associated to PFCs contamination during early stages of life. Copyright 2010 Elsevier Ltd. All rights reserved.

Perfluorochemicals and human semen quality: the LIFE study.

PubMed

Louis, Germaine M Buck; Chen, Zhen; Schisterman, Enrique F; Kim, Sungduk; Sweeney, Anne M; Sundaram, Rajeshwari; Lynch, Courtney D; Gore-Langton, Robert E; Barr, Dana Boyd

2015-01-01

The relation between persistent environmental chemicals and semen quality is evolving, although limited data exist for men recruited from general populations. We examined the relation between perfluorinated chemicals (PFCs) and semen quality among 501 male partners of couples planning pregnancy. Using population-based sampling strategies, we recruited 501 couples discontinuing contraception from two U.S. geographic regions from 2005 through 2009. Baseline interviews and anthropometric assessments were conducted, followed by blood collection for the quantification of seven serum PFCs (perfluorosulfonates, perfluorocarboxylates, and perfluorosulfonamides) using tandem mass spectrometry. Men collected a baseline semen sample and another approximately 1 month later. Semen samples were shipped with freezer packs, and analyses were performed on the day after collection. We used linear regression to estimate the difference in each semen parameter associated with a one unit increase in the natural log-transformed PFC concentration after adjusting for confounders and modeling repeated semen samples. Sensitivity analyses included optimal Box-Cox transformation of semen quality end points. Six PFCs [2-(N-methyl-perfluorooctane sulfonamido) acetate (Me-PFOSA-AcOH), perfluorodecanoate (PFDeA), perfluorononanoate (PFNA), perfluorooctane sulfonamide (PFOSA), perfluorooctane sulfonate (PFOS), and perfluorooctanoic acid (PFOA)] were associated with 17 semen quality end points before Box-Cox transformation. PFOSA was associated with smaller sperm head area and perimeter, a lower percentage of DNA stainability, and a higher percentage of bicephalic and immature sperm. PFDeA, PFNA, PFOA, and PFOS were associated with a lower percentage of sperm with coiled tails. Select PFCs were associated with certain semen end points, with the most significant associations observed for PFOSA but with results in varying directions.

Perfluorocarbon background concentrations in Europe

NASA Astrophysics Data System (ADS)

Straume, Anne Grete; Dietz, Russel N.; Koffı̀, Ernest N.'dri; Nodop, Katrin

Five studies of the background level of several perfluorocarbon compounds in Europe are here presented together with measurements from the European Tracer Experiment (ETEX). The tracers used during the two ETEX tracer releases were the perfluorocarbons (PFCs); perfluoromethylcyclohexane (C 7F 14, PMCH) and perfluoromethylcyclopentane (C 6F 12, PMCP). Their background concentrations were detected by using both passive and active sampling techniques, to define the spatial and temporal variation of the PFCs over Europe. Also the background variations of four isomers of the PFC compound perfluorodimethylcyclohexane (C 8F 16, PDCH) were studied. The results were compared to other PFC tracer studies in the U.S.A. and Europe. The mean and median values of the measured PFCs were found to vary slightly and randomly in space and time. They were found to be higher and to have a larger standard deviation than the measurements from the American studies. The background concentrations were still found to be low and stable enough for PFCs to be highly suitable for use in tracer studies. The following concentrations were found: PMCP; 4.6±0.3 fl ℓ -1, PMCH: 4.6±0.8 fl ℓ -1, ocPDCH: 0.96±0.33 fl ℓ -1, mtPDCH: 9.3±0.8 fl ℓ -1, mcPDCH: 8.8±0.8 fl ℓ -1, ptPDCH: 6.1±0.8 fl ℓ -1. A study of the correlation between the measured PFC compounds showed a significant correlation between most of the compounds, which indicate that there are no major PFC sources in Europe.

First-flush loads of perfluorinated compounds in stormwater runoff from Hayabuchi River basin, Japan served by separated sewerage system.

PubMed

Zushi, Yasuyuki; Masunaga, Shigeki

2009-08-01

Worldwide environmental pollution by perfluorinated compounds (PFCs) has been reported. PFCs have also been reported to have nonpoint sources (NPSs). A fixed-point hourly monitoring in the river was conducted during a storm event using an automatic sampler to estimate the impact of the first-flush of PFCs from NPS in this study. Perfluorocarboxylates (PFCAs) and perfluoroalkyl sulfonates (PFASs) with different chain lengths were monitored. The concentrations of short- to medium-chain-length PFCAs such as PFHpA, PFOA and PFNA, and PFASs such as PFBS, PFPeS, PFHxS, PFHpS and PFOS showed no marked increase with the storm-runoff event. However, in contrast to this, concentrations of long-chain-length PFCAs such as PFDA and PFUnA increased markedly. The concentrations of PFDA and PFUnA increased 3.4 (1.5-5.0 ng L(-1))- and 2.0 (3.3-6.7 ng L(-1))-fold, respectively. This study demonstrates that large loads of long-chain-length PFCAs are discharged to the Hayabuchi River during the first-flush after the rain event.

Comparison of Polyfluoroalkyl Compound Concentrations in Maternal Serum and Amniotic Fluid: A Pilot Study

PubMed Central

Stein, Cheryl R.; Wolff, Mary S.; Calafat, Antonia M.; Kato, Kayoko; Engel, Stephanie M.

2012-01-01

The extent to which polyfluoroalkyl compounds (PFCs) are detectable in amniotic fluid is unknown. Using paired samples from 28 women, we compared the concentration of 8 PFCs measured in serum, the standard matrix for assessing human exposure, amniotic fluid from routine amniocentesis, and urine. Perfluorooctanoate (PFOA), perfluorononanoate (PFNA), perfluorooctane sulfonate (PFOS), and perfluorohexane sulfonate (PFHxS) were detected in all maternal serum samples. The number of amniotic fluid samples with detectable concentrations differed by PFC (PFOA n=24; PFNA n=10; PFOS n=9; PFHxS n=4). The correlation coefficient between maternal serum and amniotic PFC levels varied considerably by PFC (PFOA ρ=0.64, p<0.001; PFNA ρ=0.05, p=0.9; PFOS ρ=0.76, p=0.01; PFHxS ρ=0.80, p=0.2). Using linear regression, PFOA appeared to be commonly detected in amniotic fluid if the serum concentration exceeded approximately 1.5 ng/mL whereas PFOS was rarely detected in amniotic fluid until the serum concentration was about 5.5 ng/mL. No PFCs were detected in urine. PMID:22613200

Validity aspects of the patient feedback questionnaire on consultation skills (PFC), a promising learning instrument in medical education.

PubMed

Reinders, Marcel E; Blankenstein, Annette H; Knol, Dirk L; de Vet, Henrica C W; van Marwijk, Harm W J

2009-08-01

A focus on the communicator competency is considered to be an important requirement to help physicians to acquire consultation skills. A feedback questionnaire, in which patients assess consultation skills might be a useful learning tool. An existing questionnaire on patient perception of patient-centeredness (PPPC) was adapted to cover the 'communicator' items in the competency profile. We assessed the face and content validity, the construct validity and the internal consistency of this new patient feedback on consultation skills (PFC) questionnaire. We assessed the face validity of the PFC by interviewing patients and general practice trainees (GPTs) during the developmental process. The content validity was determined by experts (n=10). First-year GPTs (23) collected 222 PFCs, from which the data were used to assess the construct validity (factor analysis), internal consistency, response rates and ceiling effects. The PFC adequately covers the corresponding 'communicator' competency (face and content validity). Factor analysis showed a one-dimensional construct. The internal consistency was high (Cronbach's alpha 0.89). For the single items, the response rate varied from 89.2% to 100%; the maximum score (ceiling effect) varied from 45.5% to 89.2%. The PFC appears to be a valid, internally consistent instrument. The PFC may be a valuable learning tool with which GPTs, other physicians and medical students can acquire feedback from patients regarding their consultation skills.

Survey of polyfluorinated chemicals (PFCs) in the atmosphere over the northeast Atlantic Ocean

NASA Astrophysics Data System (ADS)

Shoeib, Mahiba; Vlahos, Penny; Harner, Tom; Peters, Andrew; Graustein, Margaret; Narayan, Julie

2010-08-01

High volume air sampling in Bermuda, Sable Island (Nova Scotia) and along a cruise track from the Gulf of Mexico to northeast coast of the USA, was carried out to assess air concentrations, particle-gas partitioning and transport of polyfluorinated chemicals (PFCs) in this region. Samples were collected in the summer of 2007. Targeted compounds included the neutral PFCs: fluorotelomer alcohols (FTOHs), perfluoroalkyl sulfonamides (FOSAs) and perfluoroalkyl sulfonamido ethanols (FOSEs). Among the FTOHs, 8:2 FTOH was dominant in all samples. Sum of the concentration of FTOHs (gas+particle phase) were higher in Bermuda (mean, 34 pg m -3) compared to Sable Island (mean, 16 pg m -3). In cruise samples, sum of FTOHs were highly variable (mean, 81 pg m -3) reflecting contributions from land-based sources in the northeast USA with concentrations reaching as high as 156 pg m -3. Among the FOSAs and FOSEs, MeFOSE was dominant in all samples. In Bermuda, levels of MeFOSE were exceptionally high (mean, 62 pg m -3), exceeding the FTOHs. Sable Island samples also exhibited the dominance of MeFOSE but at a lower concentration (mean, 15 pg m -3). MeFOSE air concentrations (pg m -3) in cruise samples ranged from 1.6 to 73 and were not linked to land-based sources. In fact high concentrations of MeFOSE observed in Bermuda were associated with air masses that originated over the Atlantic Ocean. The partitioning to particles for 8:2 FTOH, 10:2 FTOH, MeFOSE and EtFOSE ranged from as high as 15 to 42% for cruise samples to 0.9 to 14% in Bermuda. This study provides key information for validating and developing partitioning and transport models for the PFCs.

Occurrence, fate, and fluxes of perfluorochemicals (PFCs) in an urban catchment: Marina Reservoir, Singapore.

PubMed

Nguyen, Viet Tung; Gin, Karina Yew-Hoong; Reinhard, Martin; Liu, Changhui

2012-01-01

A study was carried out to characterize the occurrence, sources and sinks of perfluorochemicals (PFCs) in the Marina Catchment and Reservoir, Singapore. Salinity depth profiles indicated the reservoir was stratified with lower layers consisting of sea water (salinity ranging from 32 to 35 g L(-1)) and a brackish surface layer containing approximately 14-65% seawater. The PFC mixture detected in catchment waters contained perfluoroalkyl carboxylates (PFCAs), particularly perfluorooctanoate (PFOA), perfluorohexanoate (PFHpA), perfluorooctane sulfonate (PFOS) and PFC transformation products. PFC concentrations in storm runoff were generally higher than those in dry weather flow of canals and rivers. PFC concentration profiles measured during storm events indicated 'first flush' behavior, probably because storm water is leaching PFC compounds from non-point sources present in the catchment area. Storm runoff carries high concentrations of suspended solids (SS), which suggests that PFC transport is via SS. In Marina Bay, PFCs are deposited in the sediments along with the SS. In sediments, the total PFC concentration was 4,700 ng kg(-1), approximately 200 times higher than in the bottom water layers. Total perfluoroalkyl sulfonates (PFSAs), particularly PFOS and 6:2 fluoro telomer sulfonate (6:2 FtS) were dominant PFCs in the sediments. PFC sorption by sediments varied with perfluorocarbon chain length, type of functional group and sediment characteristics. A first approximation analysis based on SS transport suggested that the annual PFC input into the reservoir was approximately 35 ± 12 kg y(-1). Contributions of SS, dry weather flow of river/canals, and rainfall were approximately 70, 25 and 5%, respectively. This information will be useful for improving strategies to protect the reservoir from PFC contamination.

A method for the analysis of perfluorinated compounds in environmental and drinking waters and the determination of their lowest concentration minimal reporting levels.

PubMed

Boone, J Scott; Guan, Bing; Vigo, Craig; Boone, Tripp; Byrne, Christian; Ferrario, Joseph

2014-06-06

A trace analytical method was developed for the determination of seventeen specific perfluorinated chemicals (PFCs) in environmental and drinking waters. The objectives were to optimize an isotope-dilution method to increase the precision and accuracy of the analysis of the PFCs and to eliminate the need for matrix-matched standards. A 250 mL sample of environmental or drinking water was buffered to a pH of 4, spiked with labeled surrogate standards, extracted through solid phase extraction cartridges, and eluted with ammonium hydroxide in methyl tert-butyl ether: methanol solution. The sample eluents were concentrated to volume and analyzed by liquid chromatography/tandem mass spectrometry (LC-MS/MS). The lowest concentration minimal reporting levels (LCMRLs) for the seventeen PFCs were calculated and ranged from 0.034 to 0.600 ng/L for surface water and from 0.033 to 0.640 ng/L for drinking water. The relative standard deviations (RSDs) for all compounds were <20% for all concentrations above the LCMRL. The method proved effective and cost efficient and addressed the problems with the recovery of perfluorobutanoic acid (PFBA) and other short chain PFCs. Various surface water and drinking water samples were used during method development to optimize this method. The method was used to evaluate samples from the Mississippi River at New Orleans and drinking water samples from a private residence in that same city. The method was also used to determine PFC contamination in well water samples from a fire training area where perfluorinated foams were used in training to extinguish fires. Published by Elsevier B.V.

An update: improvements in imaging perfluorocarbon-mounted plant leaves with implications for studies of plant pathology, physiology, development and cell biology

PubMed Central

Littlejohn, George R.; Mansfield, Jessica C.; Christmas, Jacqueline T.; Witterick, Eleanor; Fricker, Mark D.; Grant, Murray R.; Smirnoff, Nicholas; Everson, Richard M.; Moger, Julian; Love, John

2014-01-01

Plant leaves are optically complex, which makes them difficult to image by light microscopy. Careful sample preparation is therefore required to enable researchers to maximize the information gained from advances in fluorescent protein labeling, cell dyes and innovations in microscope technologies and techniques. We have previously shown that mounting leaves in the non-toxic, non-fluorescent perfluorocarbon (PFC), perfluorodecalin (PFD) enhances the optical properties of the leaf with minimal impact on physiology. Here, we assess the use of the PFCs, PFD, and perfluoroperhydrophenanthrene (PP11) for in vivo plant leaf imaging using four advanced modes of microscopy: laser scanning confocal microscopy (LSCM), two-photon fluorescence microscopy, second harmonic generation microscopy, and stimulated Raman scattering (SRS) microscopy. For every mode of imaging tested, we observed an improved signal when leaves were mounted in PFD or in PP11, compared to mounting the samples in water. Using an image analysis technique based on autocorrelation to quantitatively assess LSCM image deterioration with depth, we show that PP11 outperformed PFD as a mounting medium by enabling the acquisition of clearer images deeper into the tissue. In addition, we show that SRS microscopy can be used to image PFCs directly in the mesophyll and thereby easily delimit the “negative space” within a leaf, which may have important implications for studies of leaf development. Direct comparison of on and off resonance SRS micrographs show that PFCs do not to form intracellular aggregates in live plants. We conclude that the application of PFCs as mounting media substantially increases advanced microscopy image quality of living mesophyll and leaf vascular bundle cells. PMID:24795734

Erythrocyte fatty acids and risk of proliferative and nonproliferative fibrocystic disease in women in Shanghai, China123

PubMed Central

Shannon, Jackilen; King, Irena B; Lampe, Johanna W; Gao, Dao Li; Ray, Roberta M; Lin, Ming-Gang; Stalsberg, Helge; Thomas, David B

2009-01-01

Background: Although benign breast changes are more common than breast cancer, little evidence regarding risk factors for benign breast conditions is available. Omega-3 (n–3) fatty acids have antiinflammatory and antiproliferative actions and may be important in reducing the risk of benign conditions. There is a lack of research on the association of n–3 fatty acids with risk of benign fibrocystic breast changes. Objectives: The objectives of the study were to evaluate the role of n–3 and other fatty acids in the development of benign proliferative fibrocystic conditions (PFCs) and nonproliferative fibrocystic conditions (NPFCs) in the breast and to evaluate the progression of fibrocystic changes in breast cancer. Design: We conducted a case-control study to determine erythrocyte fatty acid concentrations in 155 women with NPFCs, 185 women with PFCs, 241 women with breast cancer (127 with nonproliferative and 114 with proliferative changes in the noncancerous extratumoral mammary epithelium), and 1030 control subjects. We estimated the relative risk of NPFCs, PFCs, and breast cancer with proliferative and nonproliferative changes in extratumoral tissue compared with the risk of these changes alone. Results: Women in the highest quartile of eicosapentaenoic acid concentrations were 67% less likely to have an NPFC alone or with breast cancer and 49% less likely to have breast cancer than were women with PFCs. γ-Linolenic acid (18:3n–6) was positively associated with all fibrocystic and cancerous conditions. Palmitic:palmitoleic acid (n–7 saturation index) was inversely associated with risk in all comparisons. Conclusion: Our results support a protective effects of n–3 fatty acid intake and the n–7 saturation index against benign fibrocystic breast changes and the progression of proliferative changes to breast cancer. PMID:19056601

A survey of analytical methods employed for monitoring of Advanced Oxidation/Reduction Processes for decomposition of selected perfluorinated environmental pollutants.

PubMed

Trojanowicz, Marek; Bobrowski, Krzysztof; Szostek, Bogdan; Bojanowska-Czajka, Anna; Szreder, Tomasz; Bartoszewicz, Iwona; Kulisa, Krzysztof

2018-01-15

The monitoring of Advanced Oxidation/Reduction Processes (AO/RPs) for the evaluation of the yield and mechanisms of decomposition of perfluorinated compounds (PFCs) is often a more difficult task than their determination in the environmental, biological or food samples with complex matrices. This is mostly due to the formation of hundreds, or even thousands, of both intermediate and final products. The considered AO/RPs, involving free radical reactions, include photolytic and photocatalytic processes, Fenton reactions, sonolysis, ozonation, application of ionizing radiation and several wet oxidation processes. The main attention is paid to the most commonly occurring PFCs in the environment, namely PFOA and PFOS. The most powerful and widely exploited method for this purpose is without a doubt LC/MS/MS, which allows the identification and trace quantitation of all species with detectability and resolution power depending on the particular instrumental configurations. The GC/MS is often employed for the monitoring of volatile fluorocarbons, confirming the formation of radicals in the processes of C‒C and C‒S bonds cleavage. For the direct monitoring of radicals participating in the reactions of PFCs decomposition, the molecular spectrophotometry is employed, especially electron paramagnetic resonance (EPR). The UV/Vis spectrophotometry as a detection method is of special importance in the evaluation of kinetics of radical reactions with the use of pulse radiolysis methods. The most commonly employed for the determination of the yield of mineralization of PFCs is ion-chromatography, but there is also potentiometry with ion-selective electrode and the measurements of general parameters such as Total Organic Carbon and Total Organic Fluoride. The presented review is based on about 100 original papers published in both analytical and environmental journals. Copyright © 2017 Elsevier B.V. All rights reserved.

Isomer Profiles of Perfluorochemicals in Matched Maternal, Cord, and House Dust Samples: Manufacturing Sources and Transplacental Transfer

PubMed Central

Beesoon, Sanjay; Webster, Glenys M.; Shoeib, Mahiba; Harner, Tom; Benskin, Jonathan P.

2011-01-01

Background: Perfluorochemicals (PFCs) are detectable in the general population and in the human environment, including house dust. Sources are not well characterized, but isomer patterns should enable differentiation of historical and contemporary manufacturing sources. Isomer-specific maternal–fetal transfer of PFCs has not been examined despite known developmental toxicity of perfluorooctane sulfonate (PFOS) and perfluorooctanoate (PFOA) in rodents. Objectives: We elucidated relative contributions of electrochemical (phased out in 2001) and telomer (contemporary) PFCs in dust and measured how transplacental transfer efficiency (TTE; based on a comparison of maternal and cord sera concentrations) is affected by perfluorinated chain length and isomer branching pattern. Methods: We analyzed matching samples of house dust (n = 18), maternal sera (n = 20), and umbilical cord sera (n = 20) by isomer-specific high-performance liquid chromatography tandem mass spectrometry. Results: PFOA isomer signatures revealed that telomer sources accounted for 0–95% of total PFOA in house dust (median, 31%). This may partly explain why serum PFOA concentrations are not declining in some countries despite the phase-out of electrochemical PFOA. TTE data indicate that total branched isomers crossed the placenta more efficiently than did linear isomers for both PFOS (p < 0.01) and PFOA (p = 0.02) and that placental transfer of branched isomers of PFOS increased as the branching point moved closer to the sulfonate (SO3–) end of the molecule. Conclusions: Results suggest that humans are exposed to telomer PFOA, but larger studies that also account for dietary sources should be conducted. The exposure profile of PFOS and PFOA isomers can differ between the mother and fetus—an important consideration for perinatal epidemiology studies of PFCs. PMID:21757419

Development of Extraction Methods for the Analysis of Perfluorinated Compounds in Leather with High Performance Liquid Chromatography Tandem Mass Spectrometry

NASA Astrophysics Data System (ADS)

Zhang, Yan; Wang, Youchao; Tang, Chuanjiang; Nie, Jingmei; Xu, Chengtao

2018-01-01

Perfluorinated compounds (PFCs), used to provide water, oil, grease, heat and stain repellency to a range of textile and other products, have been found to be persistent in the environment and are associated with adverse effects on humans and wildlife. This study presents the development and validation of an analytical method to determine the simultaneous presence of eleven PFCs in leather using solid-phase extraction followed by liquid chromatography-tandem mass spectrometry (LC-MS/MS). The perfluorinated compounds were primarily extracted from the samples by a liquid extraction procedure by ultrasonic, in which the parameters were optimized. Then the solid-phase extraction (SPE) is the most important advantages of the developed methodology. The sample volume and elution conditions were optimized by means of an experimental design. The proposed method was applied to determine the PFCs in leather, where the detection limits of the eleven compounds were 0.09-0.96 ng/L, and the recoveries of all compounds spiked at 5 ng/L concentration level were in the range of 65-96%, with a better RSD lower than 19% (n = 7).

Perfluorinated contaminants in fur seal pups and penguin eggs from South Shetland, Antarctica.

PubMed

Schiavone, A; Corsolini, S; Kannan, K; Tao, L; Trivelpiece, W; Torres, D; Focardi, S

2009-06-01

Perfluorinated compounds (PFCs) have emerged as a new class of global environmental pollutants. In this study, the presence of perfluorochemicals (PFCs) in penguin eggs and Antarctic fur seals was reported for the first time. Tissue samples from Antarctic fur seal pups and penguin eggs were collected during the 2003/04 breeding season. Ten PFC contaminants were determined in seal and penguin samples. The PFC concentrations in seal liver were in the decreasing order, PFOS>PFNA>PFHpA>PFUnDA while in Adélie penguin eggs were PFHpA>PFUnDA>PFDA>PFDoDA, and in Gentoo penguin eggs were PFUnDA>PFOS>PFDoDA>PFHpA. The PFC concentrations differed significantly between seals and penguins (p<0.005) and a species-specific difference was found between the two species of penguins (p<0.005). In our study we found a mean concentration of PFOS in seal muscle and liver samples of 1.3 ng/g and 9.4 ng/g wet wt, respectively, and a mean concentration in Gentoo and Adélie penguin eggs of 0.3 ng/g and 0.38 ng/g wet wt, respectively. PFCs detected in penguin eggs and seal pups suggested oviparous and viviparous transfer of PFOS to eggs and off-springs.

Blood monitoring of perfluorocarbon compounds (F-tert-butylcyclohexane, perfluoromethyldecalin and perfluorodecalin) by headspace-gas chromatography-tandem mass spectrometry.

PubMed

Giuliani, N; Saugy, M; Augsburger, M; Varlet, V

2015-11-01

A headspace-gas chromatography-tandem mass spectrometry (HS-GC-MS/MS) method for the trace measurement of perfluorocarbon compounds (PFCs) in blood was developed. Due to oxygen carrying capabilities of PFCs, application to doping and sports misuse is speculated. This study was therefore extended to perform validation methods for F-tert-butylcyclohexane (Oxycyte(®)), perfluoro(methyldecalin) (PFMD) and perfluorodecalin (PFD). The limit of detection of these compounds was established and found to be 1.2 µg/mL blood for F-tert-butylcyclohexane, 4.9 µg/mL blood for PFMD and 9.6 µg/mL blood for PFD. The limit of quantification was assumed to be 12 µg/mL blood (F-tert-butylcyclohexane), 48 µg/mL blood (PFMD) and 96 µg/mL blood (PFD). HS-GC-MS/MS technique allows detection from 1000 to 10,000 times lower than the estimated required dose to ensure a biological effect for the investigated PFCs. Thus, this technique could be used to identify a PFC misuse several hours, maybe days, after the injection or the sporting event. Clinical trials with those compounds are still required to evaluate the validation parameters with the calculated estimations. Copyright © 2015 Elsevier B.V. All rights reserved.

Perfluorinated chemicals in surface waters and sediments from northwest Georgia, USA, and their bioaccumulation in Lumbriculus variegatus

USGS Publications Warehouse

Lasier, Peter J.; Washington, John W.; Hassan, Sayed M.; Jenkins, Thomas M.

2011-01-01

Concentrations of perfluorinated chemicals (PFCs) were measured in surface waters and sediments from the Coosa River watershed in northwest Georgia, USA, to examine their distribution downstream of a suspected source. Samples from eight sites were analyzed using liquid chromatography-tandem mass spectrometry. Sediments were also used in 28-d exposures with the aquatic oligochaete, Lumbriculus variegatus, to assess PFC bioaccumulation. Concentrations of PFCs in surface waters and sediments increased significantly below a land-application site (LAS) of municipal/industrial wastewater and were further elevated by unknown sources downstream. Perfluorinated carboxylic acids (PFCAs) with eight or fewer carbons were the most prominent in surface waters. Those with 10 or more carbons predominated sediment and tissue samples. Perfluorooctane sulfonate (PFOS) was the major homolog in contaminated sediments and tissues. This pattern among sediment PFC concentrations was consistent among sites and reflected homolog concentrations emanating from the LAS. Concentrations of PFCs in oligochaete tissues revealed patterns similar to those observed in the respective sediments. The tendency to bioaccumulate increased with PFCA chain length and the presence of the sulfonate moiety. Biota-sediment accumulation factors indicated that short-chain PFCAs with fewer than seven carbons may be environmentally benign alternatives in aquatic ecosystems; however, sulfonates with four to seven carbons may be as likely to bioaccumulate as PFOS.

Perfluorinated compound concentrations in great blue heron eggs near St. Paul, Minnesota, USA, in 1993 and 2010-2011

USGS Publications Warehouse

Custer, Thomas W.; Dummer, Paul M.; Custer, Christine M.; Wu, Qian; Kannan, Kurunthachalam; Trowbridge, Annette

2013-01-01

A great blue heron (Ardea herodias) colony on Pig's Eye Island on the Mississippi River near St. Paul, Minnesota, USA, is located near several potential perfluorinated compound (PFC) sources. The PFC concentrations in great blue heron eggs reported from a 1993 collection from the Pig's Eye colony were among the highest measured in bird eggs worldwide. The objective of this investigation was to determine whether PFC concentrations in great blue heron eggs at the Pig's Eye colony have changed since 1993. Total PFC concentrations in great blue heron eggs collected at the Pig's Eye colony in 2010 and 2011 (geometric mean = 340 and 492 ng/g wet wt) were 60% lower than the 1993 collection (1,015 ng/g wet wt). Among PFCs, perfluoroalkyl sulfonate concentrations were lower and perfluoroalkyl carboxylate concentrations were higher in the 2010 and 2011 collections. Two of 20 (10%) of the eggs analyzed from Pig's Eye in 2010 and 2011 were >1,000 ng PFCs/g wet weight and the maximum PFC value (2,506 ng PFCs/g wet wt) measured in 2010 and 2011 was among the highest PFC concentration reported in bird eggs. These high concentrations are at levels associated with physiological and neurological effects in birds.

Oral LD50 toxicity modeling and prediction of per- and polyfluorinated chemicals on rat and mouse.

PubMed

Bhhatarai, Barun; Gramatica, Paola

2011-05-01

Quantitative structure-activity relationship (QSAR) analyses were performed using the LD(50) oral toxicity data of per- and polyfluorinated chemicals (PFCs) on rodents: rat and mouse. PFCs are studied under the EU project CADASTER which uses the available experimental data for prediction and prioritization of toxic chemicals for risk assessment by using the in silico tools. The methodology presented here applies chemometrical analysis on the existing experimental data and predicts the toxicity of new compounds. QSAR analyses were performed on the available 58 mouse and 50 rat LD(50) oral data using multiple linear regression (MLR) based on theoretical molecular descriptors selected by genetic algorithm (GA). Training and prediction sets were prepared a priori from available experimental datasets in terms of structure and response. These sets were used to derive statistically robust and predictive (both internally and externally) models. The structural applicability domain (AD) of the models were verified on 376 per- and polyfluorinated chemicals including those in REACH preregistration list. The rat and mouse endpoints were predicted by each model for the studied compounds, and finally 30 compounds, all perfluorinated, were prioritized as most important for experimental toxicity analysis under the project. In addition, cumulative study on compounds within the AD of all four models, including two earlier published models on LC(50) rodent analysis was studied and the cumulative toxicity trend was observed using principal component analysis (PCA). The similarities and the differences observed in terms of descriptors and chemical/mechanistic meaning encoded by descriptors to prioritize the most toxic compounds are highlighted.

Biomonitoring of Perfluorinated Compounds in Children and Adults Exposed to Perfluorooctanoate-Contaminated Drinking Water

PubMed Central

Hölzer, Jürgen; Midasch, Oliver; Rauchfuss, Knut; Kraft, Martin; Reupert, Rolf; Angerer, Jürgen; Kleeschulte, Peter; Marschall, Nina; Wilhelm, Michael

2008-01-01

Objective 40,000 residents in Arnsberg, Germany, had been exposed to drinking water contaminated with perfluorinated compounds (PFCs). Internal exposure of the residents of Arnsberg to six PFCs was assessed in comparison with reference areas. Design and participants One hundred seventy children (5–6 years of age), 317 mothers (23–49 years), and 204 men (18–69 years) took part in the cross-sectional study. Measurements Individual consumption of drinking water and personal characteristics were assessed by questionnaire and interview. Perfluorooctanoate (PFOA), perfluorooctanesulfonate (PFOS), perfluorohexanoate, perfluorohexanesulfonate (PFHxS), perfluoropentanoate, and perfluorobutanesulfonate (PFBS) in blood plasma and PFOA/PFOS in drinking water samples were measured by solid-phase extraction, high-performance liquid chromatrography, and tandem mass spectrometry detection. Results Of the various PFCs, PFOA was the main compound found in drinking water (500–640 ng/L). PFOA levels in blood plasma of residents living in Arnsberg were 4.5–8.3 times higher than those for the reference population (arithmetic means Arnsberg/controls: children 24.6/5.2 μg/L, mothers 26.7/3.2 μg/L, men 28.5/6.4 μg/L). Consumption of tap water at home was a significant predictor of PFOA blood concentrations in Arnsberg. PFHxS concentrations were significantly increased in Arnsberg compared with controls (p < 0.05). PFBS was detected in 33% of the children, 4% of the women, and 13% of the men in Arnsberg compared with 5%, 0.7%, and 3%, respectively, in the reference areas (p < 0.05). Regression analysis showed that age and male sex were significant predictors of PFOS, PFOA, and PFHxS; associations of other regressors (diet, body mass index) varied among PFCs. Conclusions PFC concentrations in blood plasma of children and adults exposed to PFC-contaminated drinking water were increased 4- to 8-fold compared with controls. PMID:18470314

EUS-guided drainage of pancreatic fluid collections using a novel lumen-apposing metal stent on an electrocautery-enhanced delivery system: a large retrospective study (with video).

PubMed

Rinninella, Emanuele; Kunda, Rastislav; Dollhopf, Markus; Sanchez-Yague, Andres; Will, Uwe; Tarantino, Ilaria; Gornals Soler, Joan; Ullrich, Sebastian; Meining, Alexander; Esteban, Josè Miguel; Enz, Thomas; Vanbiervliet, Geoffroy; Vleggaar, Frank; Attili, Fabia; Larghi, Alberto

2015-12-01

A lumen-apposing, self-expanding metal stent incorporated in an electrocautery-enhanced delivery system for EUS-guided drainage of pancreatic fluid collections (PFCs) recently has become available. The aim of this study was to analyze the safety and clinical effectiveness of this newly developed device in this clinical setting. This was a retrospective analysis of all consecutive patients with PFCs who underwent EUS-guided drainage using the study device in 13 European centers. Ninety-three patients with PFCs (80% with complex collections) underwent drainage using the study device. Penetration of the PFC was accomplished directly with the study device in 74.2% of patients, and successful stent placement was accomplished in all but 1 patient, mostly without fluoroscopic assistance. Direct endoscopic necrosectomy (DEN) was carried out in 31 of 52 cases (59.6%) of walled-off necrosis and in 2 of 4 cases (50%) of acute peripancreatic fluid collection. Complete resolution of the PFC was obtained in 86 cases (92.5%), with no recurrence during follow-up. Treatment failure occurred in 6 patients because of persistent infection requiring surgery (n = 3), perforation and massive bleeding caused by the nasocystic drainage catheter (NCDC) (n = 2), and the need for a larger opening to extract large necrotic tissue pieces (n = 1). Major adverse events occurred in 5 patients (perforation and massive bleeding caused by the NCDC in 2 patients, 1 pneumoperitoneum and 1 stent dislodgement during DEN, and 1 postdrainage infection) and were mostly not related to the drainage procedure. EUS-guided drainage with the electrocautery-enhanced delivery system is a safe, easy to perform, and a highly effective minimally invasive treatment modality for PFCs. Copyright © 2015 American Society for Gastrointestinal Endoscopy. Published by Elsevier Inc. All rights reserved.

Management of pancreatic collections with a novel endoscopically placed fully covered self-expandable metal stent: a national experience (with videos).

PubMed

Chandran, Sujievvan; Efthymiou, Marios; Kaffes, Arthur; Chen, John Wei; Kwan, Vu; Murray, Michael; Williams, David; Nguyen, Nam Quoc; Tam, William; Welch, Christine; Chong, Andre; Gupta, Saurabh; Devereaux, Ben; Tagkalidis, Peter; Parker, Frank; Vaughan, Rhys

2015-01-01

Recent medical literature on novel lumen-apposing stents for the treatment of pancreatic fluid collections (PFCs) is limited by small numbers, solo operators, and single-center experience. To evaluate a recently developed lumen-apposing, fully covered self-expandable metal stent (FCSEMS) in the management of PFCs. Retrospective case series. Thirteen tertiary and private health care centers across Australia. Forty-seven patients (median age 51 years) who underwent endoscopic management of PFCs. Insertion of FCSEMS after PFC puncture under EUS guidance. A subgroup of 9 patients underwent direct endoscopic necrosectomy. Technical and clinical success rate, adverse event rate. The technical success rate was 53 of 54 patients (98.1%), and the initial clinical success rate was 36 of 47 (76.6%), which was sustained for more than 6 months in 34 of 36 (94.4%). Early adverse events included 4 cases (7.4%) of stent migration during direct endoscopic necrosectomy, 4 cases (7.4%) of sepsis, 1 case (1.9%) of bleeding, and 1 case (1.9%) of stent migration into the fistula tract. Late adverse events were 6 (11.1%) spontaneous stent migrations, 3 (5.6%) recurrent stent occlusions, 3 (5.6%) tissue ingrowth/overgrowth, and 2 (3.7%) bleeding into PFC. The majority of stents inserted (48 of 54, 88.9%) and removed (31 of 35, 88.6%) in our study were described by the operator as superior to pigtail stents with regard to ease of use. Retrospective study. Although FCSEMSs are technically easier to insert and remove compared with traditional pigtail stents, there are significant limitations to the widespread use of FCSEMSs in the management of PFCs. These include cost, adverse events, and lower-than-expected resolution rates. Copyright © 2015 American Society for Gastrointestinal Endoscopy. Published by Elsevier Inc. All rights reserved.

Development of a double plasma gun device for investigation of effects of vapor shielding on erosion of PFC materials under ELM-like pulsed plasma bombardment

NASA Astrophysics Data System (ADS)

Sakuma, I.; Iwamoto, D.; Kitagawa, Y.; Kikuchi, Y.; Fukumoto, N.; Nagata, M.

2012-10-01

It is considered that thermal transient events such as type I edge localized modes (ELMs) could limit the lifetime of plasma-facing components (PFCs) in ITER. We have investigated surface damage of tungsten (W) materials under transient heat and particle loads by using a magnetized coaxial plasma gun (MCPG) device at University of Hyogo. The capacitor bank energy for the plasma discharge is 144 kJ (2.88 mF, 10 kVmax). Surface melting of a W material was clearly observed at the energy density of ˜2 MJ/m2. It is known that surface melting and evaporation during a transient heat load could generate a vapor cloud layer in front of the target material [1]. Then, the subsequent erosion could be reduced by the vapor shielding effect. In this study, we introduce a new experiment using two MCPG devices (MCPG-1, 2) to understand vapor shielding effects of a W surface under ELM-like pulsed plasma bombardment. The capacitor bank energy of MCPG-2 is almost same as that of MCPG-1. The second plasmoid is applied with a variable delay time after the plasmoid produced by MCPG-1. Then, a vapor cloud layer could shield the second plasma load. To verify the vapor shielding effects, surface damage of a W material is investigated by changing the delay time. In the conference, the preliminary experimental results will be shown.[4pt] [1] A. Hassanein et al., J. Nucl. Mater. 390-391, pp. 777-780 (2009).

Comparison of phase unwrapping algorithms for topography reconstruction based on digital speckle pattern interferometry

NASA Astrophysics Data System (ADS)

Li, Yuanbo; Cui, Xiaoqian; Wang, Hongbei; Zhao, Mengge; Ding, Hongbin

2017-10-01

Digital speckle pattern interferometry (DSPI) can diagnose the topography evolution in real-time, continuous and non-destructive, and has been considered as a most promising technique for Plasma-Facing Components (PFCs) topography diagnostic under the complicated environment of tokamak. It is important for the study of digital speckle pattern interferometry to enhance speckle patterns and obtain the real topography of the ablated crater. In this paper, two kinds of numerical model based on flood-fill algorithm has been developed to obtain the real profile by unwrapping from the wrapped phase in speckle interference pattern, which can be calculated through four intensity images by means of 4-step phase-shifting technique. During the process of phase unwrapping by means of flood-fill algorithm, since the existence of noise pollution, and other inevitable factors will lead to poor quality of the reconstruction results, this will have an impact on the authenticity of the restored topography. The calculation of the quality parameters was introduced to obtain the quality-map from the wrapped phase map, this work presents two different methods to calculate the quality parameters. Then quality parameters are used to guide the path of flood-fill algorithm, and the pixels with good quality parameters are given priority calculation, so that the quality of speckle interference pattern reconstruction results are improved. According to the comparison between the flood-fill algorithm which is suitable for speckle pattern interferometry and the quality-guided flood-fill algorithm (with two different calculation approaches), the errors which caused by noise pollution and the discontinuous of the strips were successfully reduced.

Levels in food and beverages and daily intake of perfluorinated compounds in Norway.

PubMed

Haug, Line Småstuen; Salihovic, Samira; Jogsten, Ingrid Ericson; Thomsen, Cathrine; van Bavel, Bert; Lindström, Gunilla; Becher, Georg

2010-08-01

Perfluorinated compounds (PFCs) have been determined in 21 samples of selected food and beverages such as meat, fish, bread, vegetables, milk, drinking water and tea from the Norwegian marked. Up to 12 different PFCs were detected in the samples. Perfluorooctanoic acid (PFOA) and perfluorooctane sulfonic acid (PFOS) were found in concentrations similar to or lower than what has been observed in other studies world-wide. Differences in the relative proportion of PFOA and PFOS between samples of animal origin and samples of non-animal origin were observed and support findings that PFOS has a higher bioaccumulation potential in animals than PFOA. Based on these 21 measurements and consumption data for the general Norwegian population, a rough estimate of the total dietary intake of PFCs was found to be around 100 ng d(-1). PFOA and PFOS contributed to about 50% of the total intake. When dividing the population in gender and age groups, estimated intakes were decreasing with increasing age and were higher in males than females. The estimated intakes of PFOS and PFOA in the present study are lower than what has been reported in studies from Spain, Germany, United Kingdom, Canada and Japan. This study illustrates that by improving the analytical methods for determination of PFC in food samples, a broad range of compounds can be detected, which is important when assessing dietary exposure. Copyright (c) 2010 Elsevier Ltd. All rights reserved.

Serum Concentrations of Polyfluoroalkyl Compounds in Faroese Whale Meat Consumers

PubMed Central

Weihe, Pal; Kato, Kayoko; Calafat, Antonia M.; Nielsen, Flemming; Wanigatunga, Amal A.; Needham, Larry L.; Grandjean, Philippe

2008-01-01

To learn the extent of human exposure to polyfluoroalkyl compounds (PFCs) in a remote fishing population, we measured, in Faroese children and pregnant women, the serum concentrations of nine PFCs, including perfluorooctane sulfonate (PFOS), perfluorooctanoate (PFOA), and perfluorononanoate (PFNA), by using on-line solid-phase extraction coupled to isotope dilution high-performance liquid chromatography-tandem mass spectrometry. The serum samples analyzed had been collected between 1993 and 2005 from 103 children 7 years of age, 79 of these children at 14 years of age, and from 12 pregnant women and their children 5 years later. PFOS was detected in all samples analyzed, and both PFOA and PFNA in all but one of the samples. The concentrations found are comparable to those reported elsewhere. Correlations between paired concentrations were poor. However, PFOS and PFNA concentrations correlated well with the frequency of pilot whale dinners and with concentrations of mercury and polychlorinated biphenyls. One whale meal every two weeks increased the PFOS concentration in 14-year olds by about 25% and PFNA by 50%. The high frequency of detection of most PFCs suggests widespread exposure in the Faroe Islands already by the early 1990s, with whale meat being an important source. Synopsis: Pilot whale meat may have been an important source of dietary exposure to PFOS and PFNA among Faroe Islands residents since the 1990s PMID:18767701

Research on Exposure to Perfluorinated Chemicals

EPA Pesticide Factsheets

Certain PFCs have been linked to adverse health effects in laboratory animals that may reflect associations between exposure to these chemicals and some health problems in the general human population.

Modeling of the ITER-like wide-angle infrared thermography view of JET.

PubMed

Aumeunier, M-H; Firdaouss, M; Travère, J-M; Loarer, T; Gauthier, E; Martin, V; Chabaud, D; Humbert, E

2012-10-01

Infrared (IR) thermography systems are mandatory to ensure safe plasma operation in fusion devices. However, IR measurements are made much more complicated in metallic environment because of the spurious contributions of the reflected fluxes. This paper presents a full predictive photonic simulation able to assess accurately the surface temperature measurement with classical IR thermography from a given plasma scenario and by taking into account the optical properties of PFCs materials. This simulation has been carried out the ITER-like wide angle infrared camera view of JET in comparing with experimental data. The consequences and the effects of the low emissivity and the bidirectional reflectivity distribution function used in the model for the metallic PFCs on the contribution of the reflected flux in the analysis are discussed.

Pancreatic fluid collections: What is the ideal imaging technique?

PubMed

Dhaka, Narendra; Samanta, Jayanta; Kochhar, Suman; Kalra, Navin; Appasani, Sreekanth; Manrai, Manish; Kochhar, Rakesh

2015-12-28

Pancreatic fluid collections (PFCs) are seen in up to 50% of cases of acute pancreatitis. The Revised Atlanta classification categorized these collections on the basis of duration of disease and contents, whether liquid alone or a mixture of fluid and necrotic debris. Management of these different types of collections differs because of the variable quantity of debris; while patients with pseudocysts can be drained by straight-forward stent placement, walled-off necrosis requires multi-disciplinary approach. Differentiating these collections on the basis of clinical severity alone is not reliable, so imaging is primarily performed. Contrast-enhanced computed tomography is the commonly used modality for the diagnosis and assessment of proportion of solid contents in PFCs; however with certain limitations such as use of iodinated contrast material especially in renal failure patients and radiation exposure. Magnetic resonance imaging (MRI) performs better than computed tomography (CT) in characterization of pancreatic/peripancreatic fluid collections especially for quantification of solid debris and fat necrosis (seen as fat density globules), and is an alternative in those situations where CT is contraindicated. Also magnetic resonance cholangiopancreatography is highly sensitive for detecting pancreatic duct disruption and choledocholithiasis. Endoscopic ultrasound is an evolving technique with higher reproducibility for fluid-to-debris component estimation with the added advantage of being a single stage procedure for both diagnosis (solid debris delineation) and management (drainage of collection) in the same sitting. Recently role of diffusion weighted MRI and positron emission tomography/CT with (18)F-FDG labeled autologous leukocytes is also emerging for detection of infection noninvasively. Comparative studies between these imaging modalities are still limited. However we look forward to a time when this gap in literature will be fulfilled.

Highly elevated levels of perfluorooctane sulfonate and other perfluorinated acids found in biota and surface water downstream of an international airport, Hamilton, Ontario, Canada.

PubMed

de Solla, S R; De Silva, A O; Letcher, R J

2012-02-01

Per- and poly-fluorinated compounds (PFCs), which include perfluorinated carboxylates (PFCAs) and sulfonates (PFSAs) and various precursors, are used in a wide variety of industrial, commercial and domestic products. This includes aqueous film forming foam (AFFF), which is used by military and commercial airports as fire suppressants. In a preliminary assessment prior to this study, very high concentrations (>1 ppm wet weight) of the PFSA, perfluorooctane sulfonate (PFOS), were discovered in the plasma of snapping turtles (Chelydra serpentina) collected in 2008 from Lake Niapenco in southern Ontario, Canada. We presently report on a suite of C(6) to C(15) PFCAs, C(4), C(6), C(8) and C(10) PFSAs, several PFC precursors (e.g. perfluorooctane sulfonamide, PFOSA), and a cyclic perfluorinated acid used in aircraft hydraulic fluid, perfluoroethylcyclohexane sulfonate (PFECHS) in surface water from the Welland River and Lake Niapenco, downstream of the John C. Munro International Airport, Hamilton, Ontario, Canada. Amphipods, shrimp, and water were sampled from the Welland River and Lake Niapenco, as well as local references. The same suite of PFCs in turtle plasma from Lake Niapenco was compared to those from other southern Ontario sites. PFOS dominated the sum PFCs in all substrates (e.g., >99% in plasma of turtles downstream the Hamilton Airport, and 72.1 to 94.1% at all other sites). PFOS averaged 2223(±247.1SE) ng/g in turtle plasma from Lake Niapenco, and ranged from 9.0 to 171.4 elsewhere. Mean PFOS in amphipods and in water were 518.1(±83.8)ng/g and 130.3(±43.6) ng/L downstream of the airport, and 19.1(±2.7) ng/g and 6.8(±0.5) ng/L at reference sites, respectively. Concentrations of selected PFCs declined with distance downstream from the airport. Although there was no known spill event or publicly reported use of AFFF associated with a fire event at the Hamilton airport, the airport is a likely major source of PFC contamination in the Welland River. Crown Copyright © 2011. Published by Elsevier Ltd. All rights reserved.

Determination of perfluorinated compounds in mollusks by matrix solid-phase dispersion and liquid chromatography-tandem mass spectrometry.

PubMed

Villaverde-de-Sáa, Eugenia; Quintana, José Benito; Rodil, Rosario; Ferrero-Refojos, Raúl; Rubí, Elisa; Cela, Rafael

2012-01-01

Perfluorinated compounds (PFCs) have been used for over 40 years in different commercial and industrial applications mainly as surfactants and surface protectors and have become an important class of marine emerging pollutants. This study presents the development and validation of a new analytical method to determine the simultaneous presence of eight PFCs in different kinds of mollusks using matrix solid-phase dispersion (MSPD) followed by liquid chromatography-tandem mass spectrometry (LC-MS/MS). Simplicity of the analytical procedure, low volume of solvent and quantity of sample required, low global price, and integration of extraction and clean-up into a single step, are the most important advantages of the developed methodology. Solvent, solid support (dispersing agent), clean-up sorbent, and their amounts were optimized by means of an experimental design. In the final method, 0.5 g of sample are dispersed with 0.2 g of diatomaceous earth and transferred into a polypropylene syringe containing 4 g of silica as clean-up sorbent. Then, analytes are eluted with 20 mL of acetonitrile. The extract is finally concentrated to a final volume of 0.5 mL in methanol, avoiding extract dryness in order to prevent evaporation losses and injected in the LC-MS/MS. The combination of this MSPD protocol with LC-MS/MS afforded detection limits from 0.05 to 0.3 ng g(-1). Also, a good linearity was established for the eight PFCs in the range from limit of quantification (LOQ) to 500 ng mL(-1) with R(2) > 0.9917. The recovery of the method was studied with three types of spiked mollusk and was in the 64-126% range. Moreover, a mussel sample was spiked and aged for more than 1 month and analyzed by the developed method and a reference method, ion-pair extraction, for comparison, producing both methods statistically equal concentration values. The method was finally applied to the determination of PFCs in different kinds of mollusks revealing concentrations up to 8.3 ng g(-1) for perfluoroundecanoic acid.

Parallel Task Management Library for MARTe

NASA Astrophysics Data System (ADS)

Valcarcel, Daniel F.; Alves, Diogo; Neto, Andre; Reux, Cedric; Carvalho, Bernardo B.; Felton, Robert; Lomas, Peter J.; Sousa, Jorge; Zabeo, Luca

2014-06-01

The Multithreaded Application Real-Time executor (MARTe) is a real-time framework with increasing popularity and support in the thermonuclear fusion community. It allows modular code to run in a multi-threaded environment leveraging on the current multi-core processor (CPU) technology. One application that relies on the MARTe framework is the Joint European Torus (JET) tokamak WAll Load Limiter System (WALLS). It calculates and monitors the temperature on metal tiles and plasma facing components (PFCs) that can melt or flake if their temperature gets too high when exposed to power loads. One of the main time consuming tasks in WALLS is the calculation of thermal diffusion models in real-time. These models tend to be described by very large state-space models thus making them perfect candidates for parallelisation. MARTe's traditional approach for task parallelisation is to split the problem into several Real-Time Threads, each responsible for a self-contained sequential execution of an input-to-output chain. This is usually possible, but it might not always be practical for algorithmic or technical reasons. Also, it might not be easily scalable with an increase in the number of available CPU cores. The WorkLibrary introduces a “GPU-like approach” of splitting work among the available cores of modern CPUs that is (i) straightforward to use in an application, (ii) scalable with the availability of cores and all of this (iii) without rewriting or recompiling the source code. The first part of this article explains the motivation behind the library, its architecture and implementation. The second part presents a real application for WALLS, a parallel version of a large state-space model describing the 2D thermal diffusion on a JET tile.

Plasma wall interaction, a key issue on the way to a steady state burning fusion device

NASA Astrophysics Data System (ADS)

Philipps, V.

2006-04-01

The International Tokamak Experimental Reactor (ITER), the first burning fusion plasma experiment based on the tokamak principle, is ready for construction. It is based on many years of fusion research resulting in a robust design in most of the areas. Present day fusion research concentrates on the remaining critical issues which are, to a large extent, connected with processes of plasma wall interaction. This is mainly due to extended duty cycle and the increase of the plasma stored energy in comparison with present-day machines. Critical topics are the lifetime of the plasma facing components (PFC) and the long-term tritium retention. These processes are controlled mainly by material erosion, both during steady state operation and transient power losses (disruptions and edge localized modes (ELMs)) and short- and long-range material migration and re-deposition. The extrapolation from present-day 'full carbon wall' devices suggests that the long-term tritium retention in a burning fusion device would be unacceptably high under these conditions allowing for only an unacceptable limited number of pulses in a D T mixture. As a consequence of this, research activities have been strengthened to understand in more detail the underlying processes of material erosion and re-deposition, to develop methods to remove retained tritium from the PFCs and remote areas of a fusion device and to explore these processes and the plasma performance in more detail with metallic PFC, such as beryllium (Be) and tungsten (W), which are foreseen for the ITER experiment. This paper outlines the main physical mechanisms leading to material erosion, migration and re-deposition and the associated fuel retention. It addresses the experimental database in these areas and describes the further research strategies that will be needed to tackle critical issues.

Measurement of the ratio of hydrogen to deuterium at the KSTAR 2009 experimental campaign

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kwak, Jong-Gu; Wang, Son Jong; Kim, Sun Ho

The control of the ratio of hydrogen to the deuterium is one of the very important issues for ion cyclotron range of frequency (ICRF) minority heating as well as the plasma wall interaction in the tokamak. The ratio of hydrogen to deuterium during the tokamak shot was deduced from the emission spectroscopy measurements during the KSTAR 2009 experimental campaign. Graphite tiles were used for the plasma facing components (PFCs) at KSTAR and its surface area exposed to the plasma was about 11 m{sup 2}. The data showed that it remained as high as around 50% during the campaign period becausemore » graphite tiles were exposed to the air for about two months and the hydrogen contents at the tiles are not fully pumped out due to the lack of baking on the PFC in the 2009 campaign. The validation of the spectroscopy method was checked by using the Zeeman effects and the ratio of hydrogen to the deuterium is compared with results from the residual gas analysis. During the tokamak shot, the ratio is low below 10% initially and saturated after around 1 s. When there is a hydrogen injection to the vessel via ion cyclotron wall conditioning and the boronization process where the carbone is used, the ratio of the hydrogen to the deuterium is increased by up to 100% and it recovers to around 50% after one day of operation. However it does not decrease below 50% at the end of the experimental campaign. It was found that the full baking on the PFC (with a high temperature and sufficient vacuum pumping) is required for the ratio control which guarantees the efficient ICRF heating at the KSTAR 2010 experimental campaign.« less

40 CFR 98.302 - GHGs to report.

Code of Federal Regulations, 2012 CFR

2012-07-01

... must report total SF6 and PFC emissions from your facility (including emissions from fugitive equipment...). For acquisitions of equipment containing or insulated with SF6 or PFCs, you must report emissions from...

40 CFR 98.302 - GHGs to report.

Code of Federal Regulations, 2014 CFR

2014-07-01

... must report total SF6 and PFC emissions from your facility (including emissions from fugitive equipment...). For acquisitions of equipment containing or insulated with SF6 or PFCs, you must report emissions from...

40 CFR 98.302 - GHGs to report.

Code of Federal Regulations, 2013 CFR

2013-07-01

... must report total SF6 and PFC emissions from your facility (including emissions from fugitive equipment...). For acquisitions of equipment containing or insulated with SF6 or PFCs, you must report emissions from...

40 CFR 98.302 - GHGs to report.

Code of Federal Regulations, 2011 CFR

2011-07-01

... must report total SF6 and PFC emissions from your facility (including emissions from fugitive equipment...). For acquisitions of equipment containing or insulated with SF6 or PFCs, you must report emissions from...

Perfluorinated Compounds In The Ohio River Basin

EPA Science Inventory

Contaminants of emerging concern (CECs) in waterways include pharmaceuticals and personal care products (PPCPs), alkylphenols, endocrine disrupting chemicals (EDCs) and perfluorinated alkyl compounds (PFCs). Their distributions and persistence in the aquatic environment remain p...

KSC-04pd1476

NASA Image and Video Library

2004-07-15

KENNEDY SPACE CENTER, FLA. - Unpacking of the Pump Flow Control Subsystem (PFCS) begins in the Space Station Processing Facility. The PFCS pumps and controls the liquid ammonia used to cool the various Orbital Replacement Units on the Integrated Equipment Assembly that make up the S6 Photo-Voltaic Power Module on the International Space Station (ISS). The fourth starboard truss segment, the S6 Truss measures 112 feet long by 39 feet wide. Its solar arrays are mounted on a “blanket” that can be folded like an accordion for delivery to the ISS. Once in orbit, astronauts will deploy the blankets to their full size. When completed, the Station's electrical power system will use eight photovoltaic solar arrays to convert sunlight to electricity. Delivery of the S6 Truss, the last power module truss segment, is targeted for mission STS-119.

KSC-04pd1477

NASA Image and Video Library

2004-07-15

KENNEDY SPACE CENTER, FLA. - Technicians attach a crane to the Pump Flow Control Subsystem (PFCS) in the Space Station Processing Facility. The PFCS pumps and controls the liquid ammonia used to cool the various Orbital Replacement Units on the Integrated Equipment Assembly that make up the S6 Photo-Voltaic Power Module on the International Space Station (ISS). The fourth starboard truss segment, the S6 Truss measures 112 feet long by 39 feet wide. Its solar arrays are mounted on a “blanket” that can be folded like an accordion for delivery to the ISS. Once in orbit, astronauts will deploy the blankets to their full size. When completed, the Station's electrical power system (EPS) will use eight photovoltaic solar arrays to convert sunlight to electricity. Delivery of the S6 Truss, the last power module truss segment, is targeted for mission STS-119.

Spectroscopic investigation of carbon migration with tungsten walls in ASDEX Upgrade

NASA Astrophysics Data System (ADS)

Kallenbach, A.; Dux, R.; Harhausen, J.; Maggi, C. F.; Neu, R.; Pütterich, T.; Rohde, V.; Schmid, K.; Wolfrum, E.; ASDEX Upgrade Team

2007-06-01

Spectroscopic measurements of carbon fluxes in the mainly tungsten-coated ASDEX Upgrade tokamak are analysed with a particle transport and migration code. The transport parameters for deuterium and carbon are calibrated against flux measurements for different experimental conditions. Additional information is obtained from the re-appearance time of carbon after a boronisation. The code reproduces the experimental finding that despite a 85% (2006 campaign) tungsten coverage of the primary PFCs, the carbon concentration in the core and edge plasma is reduced by about a factor 2 only compared to full carbon PFCs. This behaviour is explained by the strong main chamber recycling of carbon in comparison with the loss flux to the inner divertor. The quick recovery of the carbon level in the plasma after a boronisation is explained by carbon influx from the outer divertor.

A microwave plasma torch and its applications

NASA Astrophysics Data System (ADS)

Uhm, H. S.; Hong, Y. C.; Shin, D. H.

2006-05-01

A portable microwave plasma torch at atmospheric pressure by making use of magnetrons operated at 2.45 GHz and used in a home microwave oven has been developed. This electrodeless torch can be used in various areas including commercial, environmental and military applications. For example, perfluorocompounds (PFCs), which have long lifetimes and serious global warming implications, are widely used during plasma etching and plasma-assisted chamber cleaning processes in chemical vapour deposition systems. The microwave torch effectively eliminates PFCs. Efficient decomposition of toluene gas indicates the effectiveness of volatile organic compound eliminations from industrial emission and the elimination of airborne chemical and biological warfare agents. The microwave torch has been used to synthesize carbon nanotubes in an on-line system, thereby providing the opportunity of mass production of the nanotubes. There are other applications of the microwave plasma torch.

Relationship between industrial discharges and contamination of raw water resources by perfluorinated compounds: part II: Case study of a fluorotelomer polymer manufacturing plant.

PubMed

Dauchy, Xavier; Boiteux, Virginie; Rosin, Christophe; Munoz, Jean-François

2012-09-01

In this study, the concentrations of 10 perfluorinated compounds (PFCs) were measured in effluents of a fluorotelomer polymer manufacturing plant and its wastewater treatment plant. A 50-fold increase between the two effluents mass flows was observed. The water quality of two drinking water treatment plants located downstream at 15 and 25 km from the manufacturing plant was examined. An increase of the sum of PFCs was observed between the river (30 ng/L) and an alluvial well (70 ng/L), and between the raw water (9 ng/L) and the outlet of a biological treatment (97 ng/L). These results indicate a possible degradation of fluorotelomers, occurring during wastewater treatment, sediment infiltration in the alluvial aquifer, and drinking water treatment.

CADASTER QSPR Models for Predictions of Melting and Boiling Points of Perfluorinated Chemicals.

PubMed

Bhhatarai, Barun; Teetz, Wolfram; Liu, Tao; Öberg, Tomas; Jeliazkova, Nina; Kochev, Nikolay; Pukalov, Ognyan; Tetko, Igor V; Kovarich, Simona; Papa, Ester; Gramatica, Paola

2011-03-14

Quantitative structure property relationship (QSPR) studies on per- and polyfluorinated chemicals (PFCs) on melting point (MP) and boiling point (BP) are presented. The training and prediction chemicals used for developing and validating the models were selected from Syracuse PhysProp database and literatures. The available experimental data sets were split in two different ways: a) random selection on response value, and b) structural similarity verified by self-organizing-map (SOM), in order to propose reliable predictive models, developed only on the training sets and externally verified on the prediction sets. Individual linear and non-linear approaches based models developed by different CADASTER partners on 0D-2D Dragon descriptors, E-state descriptors and fragment based descriptors as well as consensus model and their predictions are presented. In addition, the predictive performance of the developed models was verified on a blind external validation set (EV-set) prepared using PERFORCE database on 15 MP and 25 BP data respectively. This database contains only long chain perfluoro-alkylated chemicals, particularly monitored by regulatory agencies like US-EPA and EU-REACH. QSPR models with internal and external validation on two different external prediction/validation sets and study of applicability-domain highlighting the robustness and high accuracy of the models are discussed. Finally, MPs for additional 303 PFCs and BPs for 271 PFCs were predicted for which experimental measurements are unknown. Copyright © 2011 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Temporal and spatial trends of perfluorinated compounds in juvenile loggerhead sea turtles (Caretta caretta) along the East Coast of the United States.

PubMed

O'Connell, Steven G; Arendt, Michael; Segars, Al; Kimmel, Tricia; Braun-McNeill, Joanne; Avens, Larisa; Schroeder, Barbara; Ngai, Lily; Kucklick, John R; Keller, Jennifer M

2010-07-01

Perfluorinated compounds (PFCs) are globally distributed persistent environmental contaminants. This study provides temporal trends as well as large-scale spatial trends of PFC concentrations in threatened juvenile loggerhead sea turtles near or from Florida Bay (FL Bay), Cape Canaveral (FL), Charleston (SC), Core Sound (NC), and Chesapeake Bay (MD). PFCs were extracted from 163 plasma and serum samples using solid-phase extraction and quantified with LC-MS/MS. Concentrations of six compounds significantly varied by site, with MD or FL Bay turtles having the highest concentrations. Perfluorooctane sulfonate (PFOS) was the predominant PFC at all sites (range: 0.31 ng/g to 39.0 ng/g). FL Bay turtles, compared to other sites, accumulated a unique PFC pattern with a higher proportion of perfluorocarboxylates compared to PFOS. Furthermore, this study was the first to statistically correlate wildlife PFC concentrations with human population, used as a proxy for urbanization and sources of PFCs to the environment. Positive relationships were found in which human population accounted for 75 and 81% of the variance in turtle PFOS and perfluoroundecanoate (PFUnA) concentrations (p = 0.06 and 0.04), respectively. PFOS and perfluorononanoate (PFNA) significantly decreased from 2000-2008 in SC turtles annually by 20 and 11%, respectively (p

Magnetic covalent triazine-based frameworks as magnetic solid-phase extraction adsorbents for sensitive determination of perfluorinated compounds in environmental water samples.

PubMed

Ren, Ji-Yun; Wang, Xiao-Li; Li, Xiao-Li; Wang, Ming-Lin; Zhao, Ru-Song; Lin, Jin-Ming

2018-02-01

Covalent organic frameworks (COFs), which are a new type of carbonaceous polymeric material, have attracted great interest because of their large surface area and high chemical and thermal stability. However, to the best of our knowledge, no work has reported the use of magnetic COFs as adsorbents for magnetic solid-phase extraction (MSPE) to enrich and determine environmental pollutants. This work aims to investigate the feasibility of using covalent triazine-based framework (CTF)/Fe 2 O 3 composites as MSPE adsorbents to enrich and analyze perfluorinated compounds (PFCs) at trace levels in water samples. Under the optimal conditions, the method developed exhibited low limits of detection (0.62-1.39 ng·L -1 ), a wide linear range (5-4000 ng L -1 ), good repeatability (1.12-9.71%), and good reproducibility (2.45-7.74%). The new method was successfully used to determine PFCs in actual environmental water samples. MSPE based on CTF/Fe 2 O 3 composites exhibits potential for analysis of PFCs at trace levels in environmental water samples. Graphical abstract Magnetic covalent triazine-based frameworks (CTFs) were used as magnetic solid-phase extraction adsorbents for the sensitive determination of perfluorinated compounds in environmental water samples. PFBA perfluorobutyric acid, PFBS perfluorobutane sulfonate, PFDA perfluorodecanoic acid, PFDoA perfluorododecanoic acid, PFHpA perfluoroheptanoic acid, PFHxA perfluorohexanoic acid, PFHxS perfluorohexane sulfonate, PFNA perfluorononanoic acid, PFOA perfluorooctanoic acid, PFPeA perfluoropentanoic acid, PFUdA Perfluoroundecanoic acid.

Removal of PFOS, PFOA and other perfluoroalkyl acids at water reclamation plants in South East Queensland Australia.

PubMed

Thompson, Jack; Eaglesham, Geoff; Reungoat, Julien; Poussade, Yvan; Bartkow, Michael; Lawrence, Michael; Mueller, Jochen F

2011-01-01

This paper examines the fate of perfluorinated sulfonates (PFSAs) and carboxylic acids (PFCAs) in two water reclamation plants in Australia. Both facilities take treated water directly from WWTPs and treat it further to produce high quality recycled water. The first plant utilizes adsorption and filtration methods alongside ozonation, whilst the second uses membrane processes and advanced oxidation to produce purified recycled water. At both facilities perfluorooctane sulfonate (PFOS), perfluorohexane sulfonate (PFHxS), perfluorohexanoic acid (PFHxA) and perfluorooctanoic acid (PFOA) were the most frequently detected PFCs. Concentrations of PFOS and PFOA in influent (WWTP effluent) ranged up to 3.7 and 16 ng L⁻¹ respectively, and were reduced to 0.7 and 12 ng L⁻¹ in the finished water of the ozonation plant. Throughout this facility, concentrations of most of the detected perfluoroalkyl compounds (PFCs) remained relatively unchanged with each successive treatment step. PFOS was an exception to this, with some removal following coagulation and dissolved air flotation/sand filtration (DAFF). At the second plant, influent concentrations of PFOS and PFOA ranged up to 39 and 29 ng L⁻¹. All PFCs present were removed from the finished water by reverse osmosis (RO) to concentrations below detection and reporting limits (0.4-1.5 ng L⁻¹). At both plants the observed concentrations were in the low parts per trillion range, well below provisional health based drinking water guidelines suggested for PFOS and PFOA. Copyright © 2010 Elsevier Ltd. All rights reserved.

Component Structure of Individual Differences in True and False Recognition of Faces

ERIC Educational Resources Information Center

Bartlett, James C.; Shastri, Kalyan K.; Abdi, Herve; Neville-Smith, Marsha

2009-01-01

Principal-component analyses of 4 face-recognition studies uncovered 2 independent components. The first component was strongly related to false-alarm errors with new faces as well as to facial "conjunctions" that recombine features of previously studied faces. The second component was strongly related to hits as well as to the conjunction/new…

Perfluorinated Compounds: An Overview

EPA Science Inventory

This volume summarizes our current understanding of the adverse health effects of this interesting group of chemicals. Many aspects of PFCs are described in detail, ranging from chemical detection to exposure assessment, from pharmacokinetics to toxicity characterization and ass...

Polyfluorinated Compounds: Past, Present, and Future

EPA Science Inventory

Interest and concern about polyfluorinated compounds (PFCs), such as perfluorooctane sulfonate (PFOS), erfluorooctanoic acid (PFOA), and an increasing number of other related compounds is growing as more is learned about these ubiquitous anthropogenic substances. Many of these co...

Meet EPA Chemist Mark Strynar, Ph.D.

EPA Pesticide Factsheets

Dr. Mark Strynar is a physical scientist in EPA's Office of Research and Development. His research interests include developing methods to measure and analyze the movement of PFCs and other xenobiotic compounds in biological and environmental media

KSC-04pd1478

NASA Image and Video Library

2004-07-15

KENNEDY SPACE CENTER, FLA. - In the Space Station Processing Facility, astronaut Tracy Caldwell (left) assists a technician check out the Pump Flow Control Subsystem (PFCS) before it is installed on the upper deck of the S6 Truss. The PFCS pumps and controls the liquid ammonia used to cool the various Orbital Replacement Units on the Integrated Equipment Assembly that make up the S6 Photo-Voltaic Power Module on the International Space Station (ISS). The fourth starboard truss segment, the S6 Truss measures 112 feet long by 39 feet wide. The solar arrays are mounted on a “blanket” that can be folded like an accordion for delivery to the ISS. Once in orbit, astronauts will deploy the blankets to their full size. When completed, the Station's electrical power system (EPS) will use eight photovoltaic solar arrays to convert sunlight to electricity. Delivery of the S6 Truss, the last power module truss segment, is targeted for mission STS-119.

KSC-04pd1480

NASA Image and Video Library

2004-07-15

KENNEDY SPACE CENTER, FLA. - In the Space Station Processing Facility, astronaut Tracy Caldwell (second from left) assists technicians position the Pump Flow Control Subsystem (PFCS) over the upper deck of the S6 Truss. The PFCS pumps and controls the liquid ammonia used to cool the various Orbital Replacement Units on the Integrated Equipment Assembly that make up the S6 Photo-Voltaic Power Module on the International Space Station (ISS). The fourth starboard truss segment, the S6 Truss measures 112 feet long by 39 feet wide. Its solar arrays are mounted on a “blanket” that can be folded like an accordion for delivery to the ISS. Once in orbit, astronauts will deploy the blankets to their full size. When completed, the Station's electrical power system (EPS) will use eight photovoltaic solar arrays to convert sunlight to electricity. Delivery of the S6 Truss, the last power module truss segment, is targeted for mission STS-119.

KSC-04pd1479

NASA Image and Video Library

2004-07-15

KENNEDY SPACE CENTER, FLA. - In the Space Station Processing Facility, a technician steadies the Pump Flow Control Subsystem (PFCS) as it is lifted and moved toward the S6 Truss. The PFCS pumps and controls the liquid ammonia used to cool the various Orbital Replacement Units on the Integrated Equipment Assembly that make up the S6 Photo-Voltaic Power Module on the International Space Station (ISS). The fourth starboard truss segment, the S6 Truss measures 112 feet long by 39 feet wide. Its solar arrays are mounted on a “blanket” that can be folded like an accordion for delivery to the ISS. Once in orbit, astronauts will deploy the blankets to their full size. When completed, the Station's electrical power system (EPS) will use eight photovoltaic solar arrays to convert sunlight to electricity. Delivery of the S6 Truss, the last power module truss segment, is targeted for mission STS-119.

KSC-04pd1481

NASA Image and Video Library

2004-07-15

KENNEDY SPACE CENTER, FLA. - In the Space Station Processing Facility, astronaut Tracy Caldwell (second from left) assists technicians lower the Pump Flow Control Subsystem (PFCS) into position onto the upper deck of the S6 Truss. The PFCS pumps and controls the liquid ammonia used to cool the various Orbital Replacement Units on the Integrated Equipment Assembly that make up the S6 Photo-Voltaic Power Module on the International Space Station (ISS). The fourth starboard truss segment, the S6 Truss measures 112 feet long by 39 feet wide. Its solar arrays are mounted on a “blanket” that can be folded like an accordion for delivery to the ISS. Once in orbit, astronauts will deploy the blankets to their full size. When completed, the Station's electrical power system (EPS) will use eight photovoltaic solar arrays to convert sunlight to electricity. Delivery of the S6 Truss, the last power module truss segment, is targeted for mission STS-119.

KSC-04pd1482

NASA Image and Video Library

2004-07-15

KENNEDY SPACE CENTER, FLA. - In the Space Station Processing Facility, astronaut Tracy Caldwell (left) assists technicians install the Pump Flow Control Subsystem (PFCS) onto the upper deck of the S6 Truss. The PFCS pumps and controls the liquid ammonia used to cool the various Orbital Replacement Units on the Integrated Equipment Assembly that make up the S6 Photo-Voltaic Power Module on the International Space Station (ISS). The fourth starboard truss segment, the S6 Truss measures 112 feet long by 39 feet wide. Its solar arrays are mounted on a “blanket” that can be folded like an accordion for delivery to the ISS. Once in orbit, astronauts will deploy the blankets to their full size. When completed, the Station's electrical power system (EPS) will use eight photovoltaic solar arrays to convert sunlight to electricity. Delivery of the S6 Truss, the last power module truss segment, is targeted for mission STS-119.

PFC and Triglyme for Li-Air Batteries: A Molecular Dynamics Study.

PubMed

Kuritz, Natalia; Murat, Michael; Balaish, Moran; Ein-Eli, Yair; Natan, Amir

2016-04-07

In this work, we present an all-atom molecular dynamics (MD) study of triglyme and perfluorinated carbons (PFCs) using classical atomistic force fields. Triglyme is a typical solvent used in nonaqueous Li-air battery cells. PFCs were recently reported to increase oxygen availability in such cells. We show that O2 diffusion in two specific PFC molecules (C6F14 and C8F18) is significantly faster than in triglyme. Furthermore, by starting with two very different initial configurations for our MD simulation, we demonstrate that C8F18 and triglyme do not mix. The mutual solubility of these molecules is evaluated both theoretically and experimentally, and a qualitative agreement is found. Finally, we show that the solubility of O2 in C8F18 is considerably higher than in triglyme. The significance of these results to Li-air batteries is discussed.

Quantifying aluminum and semiconductor industry perfluorocarbon emissions from atmospheric measurements

NASA Astrophysics Data System (ADS)

Kim, Jooil; Fraser, Paul J.; Li, Shanlan; Mühle, Jens; Ganesan, Anita L.; Krummel, Paul B.; Steele, L. Paul; Park, Sunyoung; Kim, Seung-Kyu; Park, Mi-Kyung; Arnold, Tim; Harth, Christina M.; Salameh, Peter K.; Prinn, Ronald G.; Weiss, Ray F.; Kim, Kyung-Ryul

2014-07-01

The potent anthropogenic perfluorocarbon greenhouse gases tetrafluoromethane (CF4) and hexafluoroethane (C2F6) are emitted to the atmosphere mainly by the aluminum and semiconductor industries. Global emissions of these perfluorocarbons (PFCs) calculated from atmospheric measurements are significantly greater than expected from reported national and industry-based emission inventories. In this study, in situ measurements of the two PFCs in the Advanced Global Atmospheric Gases Experiment network are used to show that their emission ratio varies according to the relative regional presence of these two industries, providing an industry-specific emission "signature" to apportion the observed emissions. Our results suggest that underestimated emissions from the global semiconductor industry during 1990-2010, as well as from China's aluminum industry after 2002, account for the observed differences between emissions based on atmospheric measurements and on inventories. These differences are significant despite the large uncertainties in emissions based on the methodologies used by these industries.

Brain Activity Related to the Judgment of Face-Likeness: Correlation between EEG and Face-Like Evaluation.

PubMed

Nihei, Yuji; Minami, Tetsuto; Nakauchi, Shigeki

2018-01-01

Faces represent important information for social communication, because social information, such as face-color, expression, and gender, is obtained from faces. Therefore, individuals' tend to find faces unconsciously, even in objects. Why is face-likeness perceived in non-face objects? Previous event-related potential (ERP) studies showed that the P1 component (early visual processing), the N170 component (face detection), and the N250 component (personal detection) reflect the neural processing of faces. Inverted faces were reported to enhance the amplitude and delay the latency of P1 and N170. To investigate face-likeness processing in the brain, we explored the face-related components of the ERP through a face-like evaluation task using natural faces, cars, insects, and Arcimboldo paintings presented upright or inverted. We found a significant correlation between the inversion effect index and face-like scores in P1 in both hemispheres and in N170 in the right hemisphere. These results suggest that judgment of face-likeness occurs in a relatively early stage of face processing.

Brain Activity Related to the Judgment of Face-Likeness: Correlation between EEG and Face-Like Evaluation

PubMed Central

Nihei, Yuji; Minami, Tetsuto; Nakauchi, Shigeki

2018-01-01

Faces represent important information for social communication, because social information, such as face-color, expression, and gender, is obtained from faces. Therefore, individuals' tend to find faces unconsciously, even in objects. Why is face-likeness perceived in non-face objects? Previous event-related potential (ERP) studies showed that the P1 component (early visual processing), the N170 component (face detection), and the N250 component (personal detection) reflect the neural processing of faces. Inverted faces were reported to enhance the amplitude and delay the latency of P1 and N170. To investigate face-likeness processing in the brain, we explored the face-related components of the ERP through a face-like evaluation task using natural faces, cars, insects, and Arcimboldo paintings presented upright or inverted. We found a significant correlation between the inversion effect index and face-like scores in P1 in both hemispheres and in N170 in the right hemisphere. These results suggest that judgment of face-likeness occurs in a relatively early stage of face processing. PMID:29503612

PFOS, PFNA, and PFOA Sub-Lethal Exposure to Embryonic Zebrafish Have Different Toxicity Profiles in Terms of Morphometrics, Behavior and Gene Expression

PubMed Central

Jantzen, Carrie E.; Annunziato, Kate A.; Bugel, Sean M.; Cooper, Keith R.

2016-01-01

Polyfluorinated compounds (PFC) are a class of anthropogenic, persistent and toxic chemicals. PFCs are detected worldwide and consist of fluorinated carbon chains of varying length, terminal groups, and industrial uses. Previous zebrafish studies in the literature as well as our own studies have shown that exposure to these chemicals at a low range of concentrations (0.02 µM – 2.0 µM; 20–2000 ppb) resulted in chemical specific developmental defects and reduced post hatch survival. It was hypothesized that sub-lethal embryonic exposure to perfluorooctanesulfonic acid (PFOS), perfluorononanoic acid (PFNA), or perfluorooctanoic acid (PFOA) would result in different responses with regard to morphometric, behavior, and gene expression in both yolk sac fry and larval zebrafish. Zebrafish were exposed to PFOS, PFOA, and PFNA (0.02, 0.2, 2.0 µM) for the first five days post fertilization (dpf) and analyzed for morphometrics (5 dpf, 14 dpf), targeted gene expression (5 dpf, 14 dpf), and locomotive behavior (14 dpf). All three PFCs commonly resulted in a decrease in total body length, increased tfc3a (muscle development) expression and decreased ap1s (protein transport) expression at 5dpf, and hyperactive locomotor activity 14 dpf. All other endpoints measured at both life-stage time points varied between each of the PFCs. PFOS, PFNA, and PFOA exposure resulted in significantly altered responses in terms of morphometric, locomotion, and gene expression endpoints, which could be manifested in field exposed teleosts. PMID:27058923

Oxygen Sensing with Perfluorocarbon-Loaded Ultraporous Mesostructured Silica Nanoparticles.

PubMed

Lee, Amani L; Gee, Clifford T; Weegman, Bradley P; Einstein, Samuel A; Juelfs, Adam R; Ring, Hattie L; Hurley, Katie R; Egger, Sam M; Swindlehurst, Garrett; Garwood, Michael; Pomerantz, William C K; Haynes, Christy L

2017-06-27

Oxygen homeostasis is important in the regulation of biological function. Disease progression can be monitored by measuring oxygen levels, thus producing information for the design of therapeutic treatments. Noninvasive measurements of tissue oxygenation require the development of tools with minimal adverse effects and facile detection of features of interest. Fluorine magnetic resonance imaging ( 19 F MRI) exploits the intrinsic properties of perfluorocarbon (PFC) liquids for anatomical imaging, cell tracking, and oxygen sensing. However, the highly hydrophobic and lipophobic properties of perfluorocarbons require the formation of emulsions for biological studies, though stabilizing these emulsions has been challenging. To enhance the stability and biological loading of perfluorocarbons, one option is to incorporate perfluorocarbon liquids into the internal space of biocompatible mesoporous silica nanoparticles. Here, we developed perfluorocarbon-loaded ultraporous mesostructured silica nanoparticles (PERFUMNs) as 19 F MRI detectable oxygen-sensing probes. Ultraporous mesostructured silica nanoparticles (UMNs) have large internal cavities (average = 1.8 cm 3 g -1 ), facilitating an average 17% loading efficiency of PFCs, meeting the threshold fluorine concentrations needed for imaging studies. Perfluoro-15-crown-5-ether PERFUMNs have the highest equivalent nuclei per PFC molecule and a spin-lattice (T 1 ) relaxation-based oxygen sensitivity of 0.0032 mmHg -1 s -1 at 16.4 T. The option of loading PFCs after synthesizing UMNs, rather than traditional in situ core-shell syntheses, allows for use of a broad range of PFC liquids from a single material. The biocompatible and tunable chemistry of UMNs combined with the intrinsic properties of PFCs makes PERFUMNs a MRI sensor with potential for anatomical imaging, cell tracking, and metabolic spectroscopy with improved stability.

The Right Place at the Right Time: Priming Facial Expressions with Emotional Face Components in Developmental Visual Agnosia

PubMed Central

Aviezer, Hillel; Hassin, Ran. R.; Perry, Anat; Dudarev, Veronica; Bentin, Shlomo

2012-01-01

The current study examined the nature of deficits in emotion recognition from facial expressions in case LG, an individual with a rare form of developmental visual agnosia (DVA). LG presents with profoundly impaired recognition of facial expressions, yet the underlying nature of his deficit remains unknown. During typical face processing, normal sighted individuals extract information about expressed emotions from face regions with activity diagnostic for specific emotion categories. Given LG’s impairment, we sought to shed light on his emotion perception by examining if priming facial expressions with diagnostic emotional face components would facilitate his recognition of the emotion expressed by the face. LG and control participants matched isolated face components with components appearing in a subsequently presented full-face and then categorized the face’s emotion. Critically, the matched components were from regions which were diagnostic or non-diagnostic of the emotion portrayed by the full face. In experiment 1, when the full faces were briefly presented (150 ms), LG’s performance was strongly influenced by the diagnosticity of the components: His emotion recognition was boosted within normal limits when diagnostic components were used and was obliterated when non-diagnostic components were used. By contrast, in experiment 2, when the face-exposure duration was extended (2000 ms), the beneficial effect of the diagnostic matching was diminished as was the detrimental effect of the non-diagnostic matching. These data highlight the impact of diagnostic facial features in normal expression recognition and suggest that impaired emotion recognition in DVA results from deficient visual integration across diagnostic face components. PMID:22349446

The right place at the right time: priming facial expressions with emotional face components in developmental visual agnosia.

PubMed

Aviezer, Hillel; Hassin, Ran R; Perry, Anat; Dudarev, Veronica; Bentin, Shlomo

2012-04-01

The current study examined the nature of deficits in emotion recognition from facial expressions in case LG, an individual with a rare form of developmental visual agnosia (DVA). LG presents with profoundly impaired recognition of facial expressions, yet the underlying nature of his deficit remains unknown. During typical face processing, normal sighted individuals extract information about expressed emotions from face regions with activity diagnostic for specific emotion categories. Given LG's impairment, we sought to shed light on his emotion perception by examining if priming facial expressions with diagnostic emotional face components would facilitate his recognition of the emotion expressed by the face. LG and control participants matched isolated face components with components appearing in a subsequently presented full-face and then categorized the face's emotion. Critically, the matched components were from regions which were diagnostic or non-diagnostic of the emotion portrayed by the full face. In experiment 1, when the full faces were briefly presented (150 ms), LG's performance was strongly influenced by the diagnosticity of the components: his emotion recognition was boosted within normal limits when diagnostic components were used and was obliterated when non-diagnostic components were used. By contrast, in experiment 2, when the face-exposure duration was extended (2000 ms), the beneficial effect of the diagnostic matching was diminished as was the detrimental effect of the non-diagnostic matching. These data highlight the impact of diagnostic facial features in normal expression recognition and suggest that impaired emotion recognition in DVA results from deficient visual integration across diagnostic face components. Copyright © 2012 Elsevier Ltd. All rights reserved.

Determination of Perfluorinated Compounds in the Upper Mississippi River Basin

EPA Science Inventory

Despite ongoing efforts to develop robust analytical methods for the determination of perfluorinated compounds (PFCs) such as perfluorooctanesulfonate (PFOS) and perfluorooctanoic acid (PFOA) in surface water, comparatively little has been published on method performance, and the...

Performance and cost effectiveness of permeable friction course (PFC) pavements.

DOT National Transportation Integrated Search

2013-02-01

In this project, the research team evaluated the performance of Permeable Friction Courses (PFC) over time and compared it against other types of wearing surface pavement layers. Several pavement sections including Asphalt Rubber (AR) PFCs, Performan...

Development of steady-state scenarios compatible with ITER-like wall conditions

NASA Astrophysics Data System (ADS)

Litaudon, X.; Arnoux, G.; Beurskens, M.; Brezinsek, S.; Challis, C. D.; Crisanti, F.; DeVries, P. C.; Giroud, C.; Pitts, R. A.; Rimini, F. G.; Andrew, Y.; Ariola, M.; Baranov, Yu F.; Brix, M.; Buratti, P.; Cesario, R.; Corre, Y.; DeLa Luna, E.; Fundamenski, W.; Giovannozzi, E.; Gryaznevich, M. P.; Hawkes, N. C.; Hobirk, J.; Huber, A.; Jachmich, S.; Joffrin, E.; Koslowski, H. R.; Liang, Y.; Loarer, Th; Lomas, P.; Luce, T.; Mailloux, J.; Matthews, G. F.; Mazon, D.; McCormick, K.; Moreau, D.; Pericoli, V.; Philipps, V.; Rachlew, E.; Reyes-Cortes, S. D. A.; Saibene, G.; Sharapov, S. E.; Voitsekovitch, I.; Zabeo, L.; Zimmermann, O.; Zastrow, K. D.; JET-EFDA Contributors, the

2007-12-01

A key issue for steady-state tokamak operation is to determine the edge conditions that are compatible both with good core confinement and with the power handling and plasma exhaust capabilities of the plasma facing components (PFCs) and divertor systems. A quantitative response to this open question will provide a robust scientific basis for reliable extrapolation of present regimes to an ITER compatible steady-state scenario. In this context, the JET programme addressing steady-state operation is focused on the development of non-inductive, high confinement plasmas with the constraints imposed by the PFCs. A new beryllium main chamber wall and tungsten divertor together with an upgrade of the heating/fuelling capability are currently in preparation at JET. Operation at higher power with this ITER-like wall will impose new constraints on non-inductive scenarios. Recent experiments have focused on the preparation for this new phase of JET operation. In this paper, progress in the development of advanced tokamak (AT) scenarios at JET is reviewed keeping this long-term objective in mind. The approach has consisted of addressing various critical issues separately during the 2006-2007 campaigns with a view to full scenario integration when the JET upgrades are complete. Regimes with internal transport barriers (ITBs) have been developed at q95 ~ 5 and high triangularity, δ (relevant to the ITER steady-state demonstration) by applying more than 30 MW of additional heating power reaching βN ~ 2 at Bo ~ 3.1 T. Operating at higher δ has allowed the edge pedestal and core densities to be increased pushing the ion temperature closer to that of the electrons. Although not yet fully integrated into a performance enhancing ITB scenario, Neon seeding has been successfully explored to increase the radiated power fraction (up to 60%), providing significant reduction of target tile power fluxes (and hence temperatures) and mitigation of edge localized mode (ELM) activity. At reduced toroidal magnetic field strength, high βN regimes have been achieved and q-profile optimization investigated for use in steady-state scenarios. Values of βN above the 'no-wall magnetohydrodynamic limit' (βN ~ 3.0) have been sustained for a resistive current diffusion time in high-δ configurations (at 1.2 MA/1.8 T). In this scenario, ELM activity has been mitigated by applying magnetic perturbations using error field correction coils to provide ergodization of the magnetic field at the plasma edge. In a highly shaped, quasi-double null X-point configuration, ITBs have been generated on the ion heat transport channel and combined with 'grassy' ELMs with ~30 MW of applied heating power (at 1.2 MA/2.7 T, q95 ~ 7). Advanced algorithms and system identification procedures have been developed with a view to developing simultaneously temperature and q-profile control in real-time. These techniques have so far been applied to the control of the q-profile evolution in JET AT scenarios.

The Motivational Salience of Faces Is Related to Both Their Valence and Dominance.

PubMed

Wang, Hongyi; Hahn, Amanda C; DeBruine, Lisa M; Jones, Benedict C

2016-01-01

Both behavioral and neural measures of the motivational salience of faces are positively correlated with their physical attractiveness. Whether physical characteristics other than attractiveness contribute to the motivational salience of faces is not known, however. Research with male macaques recently showed that more dominant macaques' faces hold greater motivational salience. Here we investigated whether dominance also contributes to the motivational salience of faces in human participants. Principal component analysis of third-party ratings of faces for multiple traits revealed two orthogonal components. The first component ("valence") was highly correlated with rated trustworthiness and attractiveness. The second component ("dominance") was highly correlated with rated dominance and aggressiveness. Importantly, both components were positively and independently related to the motivational salience of faces, as assessed from responses on a standard key-press task. These results show that at least two dissociable components underpin the motivational salience of faces in humans and present new evidence for similarities in how humans and non-human primates respond to facial cues of dominance.

Structural aspects of face recognition and the other-race effect.

PubMed

O'Toole, A J; Deffenbacher, K A; Valentin, D; Abdi, H

1994-03-01

The other-race effect was examined in a series of experiments and simulations that looked at the relationships among observer ratings of typicality, familiarity, attractiveness, memorability, and the performance variables of d' and criterion. Experiment 1 replicated the other-race effect with our Caucasian and Japanese stimuli for both Caucasian and Asian observers. In Experiment 2, we collected ratings from Caucasian observers on the faces used in the recognition task. A Varimax-rotated principal components analysis on the rating and performance data for the Caucasian faces replicated Vokey and Read's (1992) finding that typicality is composed of two orthogonal components, dissociable via their independent relationships to: (1) attractiveness and familiarity ratings and (2) memorability ratings. For Japanese faces, however, we found that typicality was related only to memorability. Where performance measures were concerned, two additional principal components dominated by criterion and by d' emerged for Caucasian faces. For the Japanese faces, however, the performance measures of d' and criterion merged into a single component that represented a second component of typicality, one orthogonal to the memorability-dominated component. A measure of face representation quality extracted from an autoassociative neural network trained with a majority of Caucasian faces and a minority of Japanese faces was incorporated into the principal components analysis. For both Caucasian and Japanese faces, the neural network measure related both to memorability ratings and to human accuracy measures. Combined, the human data and simulation results indicate that the memorability component of typicality may be related to small, local, distinctive features, whereas the attractiveness/familiarity component may be more related to the global, shape-based properties of the face.

Perfluorinated Compounds in Fish from U.S. Urban Rivers and the Great Lakes

EPA Science Inventory

Perfluorinated compounds (PFCs) have recently received scientific and regulatory attention due to their broad environmental distribution, persistence, bioaccumulative potential, and toxicity. Some studies suggest that the consumption of fish from contaminated waters may be a maj...

Perfluorinated Alkyl Compounds: Challenges To Develop Robust And Reliable Methods

EPA Science Inventory

An increasing number of studies have been conducted to investigate the environmental distribution of perfluorinated alkyl compounds (PFCs), some of which are known to be toxic in laboratory studies. Despite growing public concerns, environmental monitoring data are still limited...

Perfluorinated Compounds: Emerging POPs with Potential Immunotoxicity

EPA Science Inventory

Perfluorinated compounds (PFCs) have been recognized as an important class of environmental contaminants commonly detected in blood samples of both wildlife and humans. These compounds have been in use for more than 60 years as surface treatment chemicals, polymerization aids, an...

2008-09 National Rivers and Streams Assessment Fish Tissue Data Dictionary

EPA Pesticide Factsheets

The Office of Science and Technology (OST) is providing the fish tissue results from the 2008-09 National Rivers and Streams Assessment (NRSA). This document includes the “data dictionary” for Mercury, Selenium, PBDEs, PCBs, Pesticides and PFCs.

If You Build It, Will They Come? Patterns of Internet-Based and Face-To-Face Participation in a Parenting Program for Military Families

PubMed Central

Doty, Jennifer L; Rudi, Jessie H; Pinna, Keri L M; Hanson, Sheila K

2016-01-01

Background Some evidence suggests parents are drawn to media-based interventions over face-to-face interventions, but little is known about the factors associated with parents’ use of Internet-based or Internet-enhanced programs, especially among military families. Research is needed to understand characteristics of parents who may be most likely to use online components or attend face-to-face meetings in order to ensure maximum engagement. Objective In this study, we examined characteristics that predict various patterns of Internet use and face-to-face attendance in a parenting program designed for military families. Methods An ecological framework guided analysis of differences in patterns of Internet-based use and face-to-face attendance by parents’ demographic characteristics (gender, education, employment, and child age), incentives offered, and number of months the parent was deployed. We reported differences in the total number of online components completed over the 14 modules, total number of face-to-face sessions attended, and the use of different types of online components accessed (videos, downloadable handouts, mindfulness exercises, knowledge checks, and downloadable summaries). Then, we computed multinomial logistic regression accounting for nestedness (parents within families) to examine associations between demographic, programmatic, and military-related characteristics and patterns of engagement (use of online components and attendance at face-to-face sessions). Results Just over half (52.2%, 193/370) of the participants used the online components at least once, and the majority of participants (73.2%, 271/370) attended at least 1 face-to-face session. An examination of different patterns of participation revealed that compared with those who participated primarily in face-to-face sessions, parents who participated online but had little face-to-face participation were more likely to have received incentives than those who did not (95% CI 1.9-129.7). Among participants who had been deployed, those who had earned a 4-year degree (95% CI 1.0-2.2) and those who had been offered incentives to participate online (95% CI 2.1-58.6) were more likely to be highly engaged in online components and attend face-to-face compared with those who attended primarily face-to-face. However, those with a high number of months of deployment (95% CI 0.6-1.0) were less likely to be in the pattern of highly engaged in online components and face-to-face attendance. Compared with those who participated primarily face-to-face, deployed mothers were about 4 times more likely to engage in moderate online use with face-to-face attendance than deployed fathers (95% CI 1.21-11.83) and participate primarily online (95% CI 0.77-25.20). Conclusions Results imply that parents may be drawn to different delivery options of a parenting program (online components vs face-to-face sessions) depending on their education level, incentives to engage in online components, and their military-related experience. Results suggest potential directions for tailoring Internet-based interventions. PMID:27334833

If You Build It, Will They Come? Patterns of Internet-Based and Face-To-Face Participation in a Parenting Program for Military Families.

PubMed

Doty, Jennifer L; Rudi, Jessie H; Pinna, Keri L M; Hanson, Sheila K; Gewirtz, Abigail H

2016-06-22

Some evidence suggests parents are drawn to media-based interventions over face-to-face interventions, but little is known about the factors associated with parents' use of Internet-based or Internet-enhanced programs, especially among military families. Research is needed to understand characteristics of parents who may be most likely to use online components or attend face-to-face meetings in order to ensure maximum engagement. In this study, we examined characteristics that predict various patterns of Internet use and face-to-face attendance in a parenting program designed for military families. An ecological framework guided analysis of differences in patterns of Internet-based use and face-to-face attendance by parents' demographic characteristics (gender, education, employment, and child age), incentives offered, and number of months the parent was deployed. We reported differences in the total number of online components completed over the 14 modules, total number of face-to-face sessions attended, and the use of different types of online components accessed (videos, downloadable handouts, mindfulness exercises, knowledge checks, and downloadable summaries). Then, we computed multinomial logistic regression accounting for nestedness (parents within families) to examine associations between demographic, programmatic, and military-related characteristics and patterns of engagement (use of online components and attendance at face-to-face sessions). Just over half (52.2%, 193/370) of the participants used the online components at least once, and the majority of participants (73.2%, 271/370) attended at least 1 face-to-face session. An examination of different patterns of participation revealed that compared with those who participated primarily in face-to-face sessions, parents who participated online but had little face-to-face participation were more likely to have received incentives than those who did not (95% CI 1.9-129.7). Among participants who had been deployed, those who had earned a 4-year degree (95% CI 1.0-2.2) and those who had been offered incentives to participate online (95% CI 2.1-58.6) were more likely to be highly engaged in online components and attend face-to-face compared with those who attended primarily face-to-face. However, those with a high number of months of deployment (95% CI 0.6-1.0) were less likely to be in the pattern of highly engaged in online components and face-to-face attendance. Compared with those who participated primarily face-to-face, deployed mothers were about 4 times more likely to engage in moderate online use with face-to-face attendance than deployed fathers (95% CI 1.21-11.83) and participate primarily online (95% CI 0.77-25.20). Results imply that parents may be drawn to different delivery options of a parenting program (online components vs face-to-face sessions) depending on their education level, incentives to engage in online components, and their military-related experience. Results suggest potential directions for tailoring Internet-based interventions.

Downhole Data Transmission System

DOEpatents

Hall, David R.; Hall, Jr., H. Tracy; Pixton, David; Dahlgren, Scott; Fox, Joe

2004-04-06

A system for transmitting data through a string of down-hole components. In accordance with one aspect, the system includes a plurality of downhole components, such as sections of pipe in a drill string. Each downhole component includes a pin end and a box end, with the pin end of one downhole component being adapted to be connected to the box end of another. Each pin end includes external threads and an internal pin face distal to the external threads. Each box end includes an internal shoulder face with internal threads distal to the internal shoulder face. The internal pin face and the internal shoulder face are aligned with and proximate each other when the pin end of the one component is threaded into a box end of the other component.

Sealing device for providing a seal in a turbomachine

DOEpatents

Lacy, Benjamin Paul; Kottilingam, Srikanth Chandrudu; Porter, Christopher Donald; Schick, David Edward; Weber, David Wayne

2016-08-16

Sealing device for providing seals between adjacent components, and turbomachines utilizing such sealing devices, are provided. A sealing device includes a seal plate insertable between the adjacent components, the seal plate comprising a first face and an opposing second face. The sealing device further includes a plurality of pins extending from one of the first face or the second face, the plurality of pins configured to space the one of the first face or the second face from contact surfaces of the adjacent components.

Contact and other-race effects in configural and component processing of faces.

PubMed

Rhodes, Gillian; Ewing, Louise; Hayward, William G; Maurer, Daphne; Mondloch, Catherine J; Tanaka, James W

2009-11-01

Other-race faces are generally recognized more poorly than own-race faces. There has been a long-standing interest in the extent to which differences in contact contribute to this other-race effect (ORE). Here, we examined the effect of contact on two distinct aspects of face memory, memory for configuration and for components, both of which are better for own-race than other-race faces. Configural and component memory were measured using recognition memory tests with intact study faces and blurred (isolates memory for configuration) and scrambled (isolates memory for components) test faces, respectively. Our participants were a large group of ethnically Chinese individuals who had resided in Australia for varying lengths of time, from a few weeks to 26 years. We found that time in a Western country significantly (negatively) predicted the size of the ORE for configural, but not component, memory. There was also a trend for earlier age of arrival to predict smaller OREs in configural, but not component, memory. These results suggest that memory for configural information in other-race faces improves with experience with such faces. However, as found for recognition memory generally, the contact effects were small, indicating that other factors must play a substantial role in cross-race differences in face memory.

Degradation Testing of Fluorotelomer-based polymers (FTPs)

EPA Science Inventory

Over the last decade, concern about sources of per and polyfluorochemicals (PFCs) have led to an increasing need for information on the microbial and/or abiotic degradation of polymer materials that contain PFC structural fragments that may be released. EPA, OECD, ASTM and other...

Geographical Distribution of Perfluorinated Compounds in Fish from Minnesota Lakes and Rivers

EPA Science Inventory

Perfluorinated compounds (PFCs) have been used extensively in consumer and industrial products and are not found in environmental and biological samples around the world. Recent research suggests that fish consumption may be an important human exposure pathway to perfluorooctane...

Determination of Ten Perfluorinated Compounds in Bluegill Sunfish (Lepomis macrochirus) Fillets

EPA Science Inventory

Limited information is known about the environmental distributions of the perfluorinated compounds (PFCs) such as perfluorooctane sulfonate (PFOS) and perfluorooctanoic acid (PFOA), in part due to a lack of well characterized analytical methods that can be used to accurately mea...

Concentrations and trends of Perfluorinated chemicals in potential indoor sources from 2007 through 2011 in the US

EPA Science Inventory

Certain perfluorinated chemicals in consumer products have been associated with developmental toxicity and other adverse health effects. Temporal trends in the concentrations of selected perfluorinated chemicals (PFCs), including perfluorooctanoic acid (PFOA) and other perfluoroc...

Analysis of perfluorinated chemicals in umbilical cord blood by ultra-high performance liquid chromatography/tandem mass spectrometry.

PubMed

Lien, Guang-Wen; Wen, Ting-Wen; Hsieh, Wu-Shiun; Wu, Kuen-Yuh; Chen, Chia-Yang; Chen, Pau-Chung

2011-03-15

Perfluorinated compounds (PFCs) can cross the placental barrier and enter fetal circulation. This study aimed at developing a fast and sensitive ultra-high performance liquid chromatography/tandem mass spectrometry method for the determination of twelve perfluorinated compounds in cord blood. Samples were processed with protein precipitation using formic acid and methanol, mixed with stable isotope labeled standard, followed by sonication and centrifugation, and were analyzed using a Waters ACQUITY UPLC coupled with a Waters Quattro Premier XE triple-quadrupole mass spectrometer. The instrument was operated in selected reaction monitoring (SRM) with negative electrospray ionization. Using BEH C(18) column (2.1 mm×50 mm, 1.7 μm) with 10-mM N-methylmorpholine/methanol gradient elution provided a fast chromatographic separation (5.5 min) and sharp peaks. Intra- and inter-day calibration bias was less than 7% and intra- and inter-day calibration of relative standard deviations were within 0.02-8.22% for all the analytes and concentrations. The recoveries of PFCs spiked into bovine serum ranged from 85 to 104% with relative standard deviations from 0.02 to 6.37%. The limits of quantitation (LOQs), defined as a signal-to-noise ratio of ten, ranged from 0.15 to 3.1 ng/mL for the twelve PFCs. Perfluorooctanoic acid (PFOA), perfluorooctyl sulfonate (PFOS), perfluoroundecanoic acid (PFUA) and perfluorononanoic acid (PFNA) were detected in up to 68% of umbilical cord plasma (n=444) in Taiwan Birth Panel Study and the health effect of these chemicals on children developmental deserves further investigation. Copyright © 2011 Elsevier B.V. All rights reserved.

Spatial and temporal trends of perfluorinated compounds in Beluga Whales (Delphinapterus leucas) from Alaska.

PubMed

Reiner, Jessica L; O'Connell, Steven G; Moors, Amanda J; Kucklick, John R; Becker, Paul R; Keller, Jennifer M

2011-10-01

Wildlife from remote locations have been shown to bioaccumulate perfluorinated compounds (PFCs) in their tissues. Twelve PFCs, consisting of perfluorinated carboxylic (PFCA) and sulfonic (PFSA) acids as well as the perfluorooctane sulfonate (PFOS) precursor perfluorooctane sulfonamide (PFOSA), were measured in livers of 68 beluga whales (Delphinapterus leucas) collected from two subpopulations, Cook Inlet and eastern Chukchi Sea, in Alaska between 1989 and 2006. PFOS and PFOSA were the dominant compounds measured in both beluga stock populations, with overall median concentrations of 10.8 ng/g and 22.8 ng/g, respectively. Long-chain perfluorocarboxylates, PFCAs (9 to 14 carbons), were detected in more than 80% of the samples. Perfluoroundecanoic acid (PFUnA) and perfluorotridecanoic acid (PFTriA) made up a large percentage of the PFCAs measured with median concentrations of 8.49 ng/g and 4.38 ng/g, respectively. To compare differences in location, year, sex, and length, backward stepwise multiple regression models of the individual and total PFC concentrations were used. Spatially, the Cook Inlet belugas had higher concentrations of most PFCAs and PFOS (p < 0.05); however, these belugas had a lower median concentration of PFOSA when compared to belugas from the eastern Chukchi Sea (p < 0.05). Temporal trends indicated most PFCAs, PFHxS, PFOS, and PFOSA concentrations increased from 1989 to 2006 (p < 0.05). Males had significantly higher concentrations of PFTriA, ΣPFCA, and PFOS (p < 0.05). Perfluorononanic acid (PFNA) and PFOS showed a significant decrease in concentration with increasing animal length (p < 0.05). These observations suggest the accumulation of PFCs in belugas is influenced by year, location, sex, and length.

Serum levels of perfluoroalkyl compounds in human maternal and umbilical cord blood samples

DOE Office of Scientific and Technical Information (OSTI.GOV)

Monroy, Rocio; Morrison, Katherine; Teo, Koon

2008-09-15

Perfluoroalkyl compounds (PFCs) are end-stage metabolic products from industrial flourochemicals used in the manufacture of plastics, textiles, and electronics that are widely distributed in the environment. The objective of the present study was to quantify exposure to perfluorooctane sulfonate (PFOS), perfluorooctanoate (PFOA), perfluorodecanoic acid (PFDeA), perfluorohexane sulfonate (PFHxS), perfluoroheptanoic acid (PFHpA), and perfluorononanoic acid (PFNA) in serum samples collected from pregnant women and the umbilical cord at delivery. Pregnant women (n=101) presenting for second trimester ultrasound were recruited and PFC residue levels were quantified in maternal serum at 24-28 weeks of pregnancy, at delivery, and in umbilical cord blood (UCB;more » n=105) by liquid chromatography-mass spectrometry. Paired t-test and multiple regression analysis were performed to determine the relationship between the concentrations of each analyte at different sample collection time points. PFOA and PFOS were detectable in all serum samples analyzed including the UCB. PFOS serum levels (mean{+-}S.D.) were significantly higher (p<0.001) in second trimester maternal serum (18.1{+-}10.9 ng/mL) than maternal serum levels at delivery (16.2{+-}10.4 ng/mL), which were higher than the levels found in UCB (7.3{+-}5.8 ng/mL; p<0.001). PFHxS was quantifiable in 46/101 (45.5%) maternal and 21/105 (20%) UCB samples with a mean concentration of 4.05{+-}12.3 and 5.05{+-}12.9 ng/mL, respectively. There was no association between serum PFCs at any time point studied and birth weight. Taken together our data demonstrate that although there is widespread exposure to PFCs during development, these exposures do not affect birth weight.« less

The serum concentrations of perfluoroalkyl compounds were inversely associated with growth parameters in 2-year old children.

PubMed

Lee, Young Ah; Kim, Jin Hee; Jung, Hae Woon; Lim, Youn-Hee; Bae, Sanghyuk; Kho, Younglim; Hong, Yun-Chul; Shin, Choong Ho; Yang, Sei Won

2018-07-01

The relationship between the serum concentrations of perfluoroalkyl compounds (PFCs) and growth parameters was investigated in 2-year-old Korean children. The study included 361 children aged 2years (192 boys and 169 girls; 22-27months), born at term appropriate-for-gestational-age, who visited between 2012 and 2013. Growth parameters of height and weight, and serum samples were collected from 2-year-old children. Four PFCs (perfluorohexane sulfonic acid [PFHxS], perfluorooctane sulfonic acid [PFOS], perfluorooctanoic acid [PFOA], and perfluorononanoic acid [PFNA]), perfluorodecanoic acid (PFDA), perfluoroundecanoic acid (PFUnDA), and perfluoroheptanoic acid (PFHpA) were detected in >99, 93.4, 89.8, and 74.2% of the serum samples, respectively. The duration of breastfeeding was positively associated with the serum concentrations of ln-transformed PFHxS, PFOS, PFHpA, PFOA, PFNA, PFDA, and PFUnDA (all P<0.001). Height at 2years of age was inversely related to PFHxS, PFOS, PFOA, PFNA, and PFDA concentrations (adjusted β per ln unit [95% confidence interval, CI]: -0.84 [-1.26, -0.42], -0.77 [-1.27, -0.15], -0.91 [-1.36, -0.47], -0.48 [-1.40, -0.51], and -0.44 [-0.77, -0.10] cm, respectively), after adjusting for age, sex, and midparental height. Weight at 2years of age was inversely associated with PFNA (adjusted β per ln unit [95% CI]: -0.32 [-0.48, -0.15] kg), after adjusting for age, sex, and parental BMI. In conclusion, the serum concentrations of PFCs were inversely associated with growth parameters in 2-year-old children. Copyright © 2018 Elsevier B.V. All rights reserved.

Exploring the Role of In-Person Components for Online Health Behavior Change Interventions: Can a Digital Person-to-Person Component Suffice?

PubMed Central

Kane, Deborah; Senn, Charlene Y; Woodruff, Sarah J

2018-01-01

The growth of the digital environment provides tremendous opportunities to revolutionize health behavior change efforts. This paper explores the use of Web-based, mobile, and social media health behavior change interventions and determines whether there is a need for a face-to-face or an in-person component. It is further argued that that although in-person components can be beneficial for online interventions, a digital person-to-person component can foster similar results while dealing with challenges faced by traditional intervention approaches. Using a digital person-to-person component is rooted in social and behavioral theories such as the theory of reasoned action, and the social cognitive theory, and further justified by the human support constructs of the model of supportive accountability. Overall, face-to-face and online behavior change interventions have their respective advantages and disadvantages and functions, yet both serve important roles. It appears that it is in fact human support that is the most important component in the effectiveness and adherence of both face-to-face and online behavior change interventions, and thoughtfully introducing a digital person-to-person component, to replace face-to-face interactions, can provide the needed human support while diminishing the barriers of in-person meetings. The digital person-to-person component must create accountability, generate opportunities for tailored feedback, and create social support to successfully create health behavior change. As the popularity of the online world grows, and the interest in using the digital environment for health behavior change interventions continues to be embraced, further research into not only the use of online interventions, but the use of a digital person-to-person component, must be explored. PMID:29643048

Holistic processing of face configurations and components.

PubMed

Hayward, William G; Crookes, Kate; Chu, Ming Hon; Favelle, Simone K; Rhodes, Gillian

2016-10-01

Although many researchers agree that faces are processed holistically, we know relatively little about what information holistic processing captures from a face. Most studies that assess the nature of holistic processing do so with changes to the face affecting many different aspects of face information (e.g., different identities). Does holistic processing affect every aspect of a face? We used the composite task, a common means of examining the strength of holistic processing, with participants making same-different judgments about configuration changes or component changes to 1 portion of a face. Configuration changes involved changes in spatial position of the eyes, whereas component changes involved lightening or darkening the eyebrows. Composites were either aligned or misaligned, and were presented either upright or inverted. Both configuration judgments and component judgments showed evidence of holistic processing, and in both cases it was strongest for upright face composites. These results suggest that holistic processing captures a broad range of information about the face, including both configuration-based and component-based information. (PsycINFO Database Record (c) 2016 APA, all rights reserved).

Polyfluoroalkyl Chemicals in the Serum and Milk of Breastfeeding Women.

EPA Science Inventory

Polyfluoroalkyl chemicals (PFCs) comprise a group of man-made organic compounds, some of which are persistent contaminants with developmental toxicity shown in laboratory animals. There is a paucity of human perinatal exposure data. The US EPA conducted a pilot study (Methods Adv...

75 FR 70248 - Endocrine Disruptor Screening Program; Second List of Chemicals for Tier 1 Screening

Federal Register 2010, 2011, 2012, 2013, 2014

2010-11-17

...., persons who manufacture, import or process chemical substances. Pesticide, fertilizer, and other... pesticide, fertilizer and agricultural chemicals. Scientific research and development services (NAICS code... water contaminants, such as halogenated organic chemicals, dioxins, flame retardants (PBDEs, PCBs, PFCs...

Contaminants Of Emerging Concern Within The Ohio River And Its Tributaries

EPA Science Inventory

Contaminants of emerging concern such as PPCPs, alkylphenols, EDCs, and PFCs in waterways have been increasing public concern. The extent and persistence of their occurrence in surface waters remains unclear. Though ther are many sources of these contaminants, research has focu...

14 CFR 158.65 - Reporting requirements: Collecting air carriers.

Code of Federal Regulations, 2010 CFR

2010-01-01

... TRANSPORTATION (CONTINUED) AIRPORTS PASSENGER FACILITY CHARGES (PFC'S) Reporting, Recordkeeping and Audits § 158.65 Reporting requirements: Collecting air carriers. (a) Each air carrier collecting PFCs for a public... carrier and airport involved, (ii) The total PFC revenue collected, (iii) The total PFC revenue refunded...

14 CFR 158.65 - Reporting requirements: Collecting air carriers.

Code of Federal Regulations, 2013 CFR

2013-01-01

... TRANSPORTATION (CONTINUED) AIRPORTS PASSENGER FACILITY CHARGES (PFC'S) Reporting, Recordkeeping and Audits § 158.65 Reporting requirements: Collecting air carriers. (a) Each air carrier collecting PFCs for a public... carrier and airport involved, (ii) The total PFC revenue collected, (iii) The total PFC revenue refunded...

14 CFR 158.65 - Reporting requirements: Collecting air carriers.

Code of Federal Regulations, 2011 CFR

2011-01-01

... TRANSPORTATION (CONTINUED) AIRPORTS PASSENGER FACILITY CHARGES (PFC'S) Reporting, Recordkeeping and Audits § 158.65 Reporting requirements: Collecting air carriers. (a) Each air carrier collecting PFCs for a public... carrier and airport involved, (ii) The total PFC revenue collected, (iii) The total PFC revenue refunded...

14 CFR 158.65 - Reporting requirements: Collecting air carriers.

Code of Federal Regulations, 2012 CFR

2012-01-01

... TRANSPORTATION (CONTINUED) AIRPORTS PASSENGER FACILITY CHARGES (PFC'S) Reporting, Recordkeeping and Audits § 158.65 Reporting requirements: Collecting air carriers. (a) Each air carrier collecting PFCs for a public... carrier and airport involved, (ii) The total PFC revenue collected, (iii) The total PFC revenue refunded...

14 CFR 158.65 - Reporting requirements: Collecting air carriers.

Code of Federal Regulations, 2014 CFR

2014-01-01

... TRANSPORTATION (CONTINUED) AIRPORTS PASSENGER FACILITY CHARGES (PFC'S) Reporting, Recordkeeping and Audits § 158.65 Reporting requirements: Collecting air carriers. (a) Each air carrier collecting PFCs for a public... carrier and airport involved, (ii) The total PFC revenue collected, (iii) The total PFC revenue refunded...

Accumulation of perfluorinated compounds in captive Bengal tigers (Panthera tigris tigris) and African lions (Panthera leo Linnaeus) in China.

PubMed

Li, Xuemei; Yeung, Leo Wai Yin; Taniyasu, Sachi; Lam, Paul K S; Yamashita, Nobuyoshi; Xu, Muqi; Dai, Jiayin

2008-11-01

The accumulation of perfluorinated compounds (PFCs) in the sera of captive wildlife species Bengal tigers (Panthera tigris tigris) and African lions (Panthera leo Linnaeus) from Harbin Wildlife Park, Heilongjiang Province, in China were analyzed by high-performance liquid chromatography-tandem mass spectrometry (HPLC-MS/MS). Perfluorooctanesulfonate (PFOS) was the predominant contaminant with a mean serum concentration of 1.18 ng mL(-1) in tigers and 2.69 ng mL(-1) in lions. Perfluorononanoic acid (PFNA) was the second most prevalent contaminant in both species. The composition profiles of the tested PFCs differed between tigers and lions, and the percentages of perfluorooctanoic acid (PFOA) were greater in lions than in tigers, indicating different exposures and/or metabolic capabilities between the two species. Assessments of the risk of PFC contamination to the two species were obtained by comparing measured concentrations to points of departure or toxicity reference values (TRVs). Results suggest no risk of PFOS exposure or toxicity for the two species.

Phase-Change Nanoparticles Using Highly Volatile Perfluorocarbons: Toward a Platform for Extravascular Ultrasound Imaging

PubMed Central

Matsunaga, Terry O.; Sheeran, Paul S.; Luois, Samantha; Streeter, Jason E.; Mullin, Lee B.; Banerjee, Bhaskar; Dayton, Paul A.

2012-01-01

Recent efforts using perfluorocarbon (PFC) nanoparticles in conjunction with acoustic droplet vaporization has introduced the possibility of expanding the diagnostic and therapeutic capability of ultrasound contrast agents to beyond the vascular space. Our laboratories have developed phase-change nanoparticles (PCNs) from the highly volatile PFCs decafluorobutane (DFB, bp =-2 °C) and octafluoropropane (OFP, bp =-37 °C ) for acoustic droplet vaporization. Studies with commonly used clinical ultrasound scanners have demonstrated the ability to vaporize PCN emulsions with frequencies and mechanical indices that may significantly decrease tissue bioeffects. In addition, these contrast agents can be formulated to be stable at physiological temperatures and the perfluorocarbons can be mixed to modulate the balance between sensitivity to ultrasound and general stability. We herein discuss our recent efforts to develop finely-tuned diagnostic/molecular imaging agents for tissue interrogation. We discuss studies currently under investigation as well as potential diagnostic and therapeutic paradigms that may emerge as a result of formulating PCNs with low boiling point PFCs. PMID:23382775

Regional atmospheric emissions determined from measurements at Jeju Island, Korea: Halogenated compounds from China

NASA Astrophysics Data System (ADS)

Kim, Jooil; Li, Shanlan; Kim, Kyung-Ryul; Stohl, Andreas; Mühle, Jens; Kim, Seung-Kyu; Park, Mi-Kyung; Kang, Dong-Jin; Lee, Gangwoong; Harth, Christina M.; Salameh, Peter K.; Weiss, Ray F.

2010-06-01

High-frequency in-situ measurements of a wide range of halogenated compounds including chlorofluorocarbons (CFCs), halons, hydrochlorofluorocarbons (HCFCs), hydrofluorocarbons (HFCs), perfluorinated compounds (PFCs), sulfur hexafluoride (SF6), and other chlorinated and brominated compounds have been made at Gosan (Jeju Island, Korea). Regional emissions of HCFC-22 (CHClF2) calculated from inverse modeling were combined with interspecies correlation methods to estimate national emissions for China, a major emitter of industrial halogenated gases. Our results confirm the signs of successful phase-out of primary ozone-depleting species such as CFCs, halons and many chlorinated or brominated compounds, along with substantial emissions of replacement HCFCs. Emissions derived for HFCs, PFCs, and SF6 were compared to published estimates and found to be a significant fraction of global totals. Overall, Chinese emissions of the halogenated compounds discussed here represent 19(14-17)% and 20(15-26)% of global emissions when evaluated in terms of their Ozone Depletion Potentials and 100-year Global Warming Potentials, respectively.

DEVELOPMENT OF AN EPA METHOD FOR PERFLUOROALKYL COMPOUNDS IN DRINKING WATER

EPA Science Inventory

Over the past five years, perfluoroalkyl compounds (PFCs) in water have become an emerging environmental issue. This research focuses on the development of an analytical method for the determination of perfluoroalkyl compounds in drinking water to be used by EPA's Office of Grou...

Pilot Scale Application of a Method for the Analysis of Perfluorinated Compounds in Surface Soils

EPA Science Inventory

A growing number of studies now indicate that perfluorinated compounds (PFCs) are globally distributed in the environment. Their widespread distribution and presence in remote locations has led to questions about the importance of atmospheric and oceanic transport. Describing the...

Bioaugmentation with Vaults: Novel In Situ Remediation Strategy for Transformation of Perfluoroalkyl Compounds

DTIC Science & Technology

2016-01-01

degradation of poly- and perfluoroalkyl compounds (PFCs), and potentially other water contaminants, without the need for repeated bioaugmentation with...active cultures or stimulation with nutrients. We designed a single-step method for encapsulating lignin peroxidases (LiP), manganese peroxidases (MnP

Absorption and excretion of 14C-perfluorooctanoic acid (PFOA)in angus cattle (Bos taurus)

USDA-ARS?s Scientific Manuscript database

Perfluorinated chemicals (PFCs), such as perfluorooctanoic acid (PFOA), are environmentally persistent industrial chemicals often found in biosolids. Application of these biosolids to pastures raises concern about accumulation of PFOA in the edible tissues of food animals. Because data on the absorp...

Contaminants Of Emerging Concern Within The Mainstem Of The Ohio River And its Tributaries

EPA Science Inventory

Contaminants of emerging concern such as PPCPs, alkylphenols, EDCs, and PFCs in waterways have been of increasing public concern. The extent and persistence of their occurrence in surface waters remains unclear. Though there are many sources of these contaminants, research has ...

14 CFR 158.63 - Reporting requirements: Public agency.

Code of Federal Regulations, 2013 CFR

2013-01-01

... (CONTINUED) AIRPORTS PASSENGER FACILITY CHARGES (PFC'S) Reporting, Recordkeeping and Audits § 158.63... PFC level for each project; and (4) Each project's current schedule. (b) The report shall be provided... collecting PFCs for the public agency with a copy to the appropriate FAA Airports Office. The quarterly...

14 CFR 158.63 - Reporting requirements: Public agency.

Code of Federal Regulations, 2010 CFR

2010-01-01

... (CONTINUED) AIRPORTS PASSENGER FACILITY CHARGES (PFC'S) Reporting, Recordkeeping and Audits § 158.63... PFC level for each project; and (4) Each project's current schedule. (b) The report shall be provided... collecting PFCs for the public agency with a copy to the appropriate FAA Airports Office. The quarterly...

14 CFR 158.63 - Reporting requirements: Public agency.

Code of Federal Regulations, 2014 CFR

2014-01-01

... (CONTINUED) AIRPORTS PASSENGER FACILITY CHARGES (PFC'S) Reporting, Recordkeeping and Audits § 158.63... PFC level for each project; and (4) Each project's current schedule. (b) The report shall be provided... collecting PFCs for the public agency with a copy to the appropriate FAA Airports Office. The quarterly...

14 CFR 158.63 - Reporting requirements: Public agency.

Code of Federal Regulations, 2012 CFR

2012-01-01

... (CONTINUED) AIRPORTS PASSENGER FACILITY CHARGES (PFC'S) Reporting, Recordkeeping and Audits § 158.63... PFC level for each project; and (4) Each project's current schedule. (b) The report shall be provided... collecting PFCs for the public agency with a copy to the appropriate FAA Airports Office. The quarterly...

14 CFR 158.63 - Reporting requirements: Public agency.

Code of Federal Regulations, 2011 CFR

2011-01-01

... (CONTINUED) AIRPORTS PASSENGER FACILITY CHARGES (PFC'S) Reporting, Recordkeeping and Audits § 158.63... PFC level for each project; and (4) Each project's current schedule. (b) The report shall be provided... collecting PFCs for the public agency with a copy to the appropriate FAA Airports Office. The quarterly...

Characterization of a Wide Array of Fluorinated Organic Compounds in Contaminated Soils

EPA Science Inventory

Herein we report the results of analyses on the concentrations of perfluorinated compounds (PFCs) and fluorotelomer alcohols (FTOHs) in soils from a site that has been impacted by human activities. Soil samples were collected from several locations that had been impacted and one...

Levels of persistent contaminants in relation to fish consumption among older male anglers in Wisconsin.

PubMed

Christensen, Krista Y; Thompson, Brooke A; Werner, Mark; Malecki, Kristen; Imm, Pamela; Anderson, Henry A

2016-03-01

Fish are an important source of nutrients which may reduce risk of adverse health outcomes such as cardiovascular disease; however, fish may also contain significant amounts of environmental pollutants such as mercury, polychlorinated biphenyls (PCBs), polybrominated diphenyl ethers (PBDEs), and perfluorinated compounds (PFCs, also called perfluoroalkyl compounds), which confer increased risk for adverse health effects. The Wisconsin Departments of Health Services and Natural Resources developed a survey instrument, along with a strategy to collect human biological samples to assess the risks and benefits associated with long-term fish consumption among older male anglers in Wisconsin. The target population was men aged 50 years and older, who fish Wisconsin waters and live in the state of Wisconsin. Participants provided blood and hair samples and completed a detailed (paper) questionnaire, which included questions on basic demographics, health status, location of catch and species of fish caught/eaten, consumption of locally caught and commercially purchased fish, and awareness and source of information for local and statewide consumption guidelines. Biological samples were used to assess levels of PCBs, PBDEs, PFCs (blood), and mercury (hair and blood). Quantile regression analysis was used to investigate the associations between biomarker levels and self-reported consumption of fish from the Great Lakes and other areas of concern, other locally caught fish, and commercially purchased fish (meals per year). Respondents had a median age of 60.5 (interquartile range: 56, 67) years. The median fish consumption was 54.5 meals per year, with most fish meals coming from locally-caught fish. Participants had somewhat higher mercury levels compared with the US general population, while levels of other contaminants were similar or lower. Multivariate regression models showed that consumption of fish from the Great Lakes and areas of concern was associated with higher levels of each of the contaminants with the exception of PBDEs, as was consumption of locally caught fish from other water bodies. All commercial fish consumption was also associated with both hair and blood mercury. When looking at specific PCB, PBDE and PFC analytes, consumption of fish from the Great Lakes and areas of concern was associated with higher levels of each of the individual PCB congeners examined, as well as higher levels of all of the PFCs examined, with the exception of PFHxS. Among the PFCs, locally caught fish from other water bodies was also associated with higher levels of each of the congeners examined except PFHxS. Finally, all commercial fish was associated with higher levels of PFHxS. Published by Elsevier GmbH.

US-Japan workshop Q-181 on high heat flux components and plasma-surface interactions for next devices: Proceedings

DOE Office of Scientific and Technical Information (OSTI.GOV)

McGrath, R.T.; Yamashina, T.

This report contain viewgraphs of papers from the following sessions: plasma facing components issues for future machines; recent PMI results from several tokamaks; high heat flux technology; plasma facing components design and applications; plasma facing component materials and irradiation damage; boundary layer plasma; plasma disruptions; conditioning and tritium; and erosion/redeposition.

Components of Effective Cognitive-Behavioral Therapy for Pediatric Headache: A Mixed Methods Approach

PubMed Central

Law, Emily F.; Beals-Erickson, Sarah E.; Fisher, Emma; Lang, Emily A.; Palermo, Tonya M.

2017-01-01

Internet-delivered treatment has the potential to expand access to evidence-based cognitive-behavioral therapy (CBT) for pediatric headache, and has demonstrated efficacy in small trials for some youth with headache. We used a mixed methods approach to identify effective components of CBT for this population. In Study 1, component profile analysis identified common interventions delivered in published RCTs of effective CBT protocols for pediatric headache delivered face-to-face or via the Internet. We identified a core set of three treatment components that were common across face-to-face and Internet protocols: 1) headache education, 2) relaxation training, and 3) cognitive interventions. Biofeedback was identified as an additional core treatment component delivered in face-to-face protocols only. In Study 2, we conducted qualitative interviews to describe the perspectives of youth with headache and their parents on successful components of an Internet CBT intervention. Eleven themes emerged from the qualitative data analysis, which broadly focused on patient experiences using the treatment components and suggestions for new treatment components. In the Discussion, these mixed methods findings are integrated to inform the adaptation of an Internet CBT protocol for youth with headache. PMID:29503787

Components of Effective Cognitive-Behavioral Therapy for Pediatric Headache: A Mixed Methods Approach.

PubMed

Law, Emily F; Beals-Erickson, Sarah E; Fisher, Emma; Lang, Emily A; Palermo, Tonya M

2017-01-01

Internet-delivered treatment has the potential to expand access to evidence-based cognitive-behavioral therapy (CBT) for pediatric headache, and has demonstrated efficacy in small trials for some youth with headache. We used a mixed methods approach to identify effective components of CBT for this population. In Study 1, component profile analysis identified common interventions delivered in published RCTs of effective CBT protocols for pediatric headache delivered face-to-face or via the Internet. We identified a core set of three treatment components that were common across face-to-face and Internet protocols: 1) headache education, 2) relaxation training, and 3) cognitive interventions. Biofeedback was identified as an additional core treatment component delivered in face-to-face protocols only. In Study 2, we conducted qualitative interviews to describe the perspectives of youth with headache and their parents on successful components of an Internet CBT intervention. Eleven themes emerged from the qualitative data analysis, which broadly focused on patient experiences using the treatment components and suggestions for new treatment components. In the Discussion, these mixed methods findings are integrated to inform the adaptation of an Internet CBT protocol for youth with headache.

Electrophysiological evidence for parts and wholes in visual face memory.

PubMed

Towler, John; Eimer, Martin

2016-10-01

It is often assumed that upright faces are represented in a holistic fashion, while representations of inverted faces are essentially part-based. To assess this hypothesis, we recorded event-related potentials (ERPs) during a sequential face identity matching task where successively presented pairs of upright or inverted faces were either identical or differed with respect to their internal features, their external features, or both. Participants' task was to report on each trial whether the face pair was identical or different. To track the activation of visual face memory representations, we measured N250r components that emerge over posterior face-selective regions during the activation of visual face memory representations by a successful identity match. N250r components to full identity repetitions were smaller and emerged later for inverted as compared to upright faces, demonstrating that image inversion impairs face identity matching processes. For upright faces, N250r components were also elicited by partial repetitions of external or internal features, which suggest that the underlying identity matching processes are not exclusively based on non-decomposable holistic representations. However, the N250r to full identity repetitions was super-additive (i.e., larger than the sum of the two N250r components to partial repetitions of external or internal features) for upright faces, demonstrating that holistic representations were involved in identity matching processes. For inverted faces, N250r components to full and partial identity repetitions were strictly additive, indicating that the identity matching of external and internal features operated in an entirely part-based fashion. These results provide new electrophysiological evidence for qualitative differences between representations of upright and inverted faces in the occipital-temporal face processing system. Copyright © 2016 Elsevier Ltd. All rights reserved.

Exploring the Role of In-Person Components for Online Health Behavior Change Interventions: Can a Digital Person-to-Person Component Suffice?

PubMed

Santarossa, Sara; Kane, Deborah; Senn, Charlene Y; Woodruff, Sarah J

2018-04-11

The growth of the digital environment provides tremendous opportunities to revolutionize health behavior change efforts. This paper explores the use of Web-based, mobile, and social media health behavior change interventions and determines whether there is a need for a face-to-face or an in-person component. It is further argued that that although in-person components can be beneficial for online interventions, a digital person-to-person component can foster similar results while dealing with challenges faced by traditional intervention approaches. Using a digital person-to-person component is rooted in social and behavioral theories such as the theory of reasoned action, and the social cognitive theory, and further justified by the human support constructs of the model of supportive accountability. Overall, face-to-face and online behavior change interventions have their respective advantages and disadvantages and functions, yet both serve important roles. It appears that it is in fact human support that is the most important component in the effectiveness and adherence of both face-to-face and online behavior change interventions, and thoughtfully introducing a digital person-to-person component, to replace face-to-face interactions, can provide the needed human support while diminishing the barriers of in-person meetings. The digital person-to-person component must create accountability, generate opportunities for tailored feedback, and create social support to successfully create health behavior change. As the popularity of the online world grows, and the interest in using the digital environment for health behavior change interventions continues to be embraced, further research into not only the use of online interventions, but the use of a digital person-to-person component, must be explored. ©Sara Santarossa, Deborah Kane, Charlene Y Senn, Sarah J Woodruff. Originally published in the Journal of Medical Internet Research (http://www.jmir.org), 11.04.2018.

Application of WWTP Biosolids and Resulting Perfluorinated Compound Contamination of Surface and Well Water in Decatur, Alabama, USA

EPA Science Inventory

Perfluorinated chemicals (PFCs) such as perfluorooctanoic acid (PFOA) and perfluorooctane sulfonate (PFOS) have been produced and used in a wide range of industrial and consumer products for many decades. Their resistance to degradation has led to their widespread distribution in...

Serum concentrations of perfluorinated compounds (PFC) among selected populations of children and Adults in California

EPA Science Inventory

Perfluorinated compounds (PFCs) have been widely used in industrial applications and consumer products. Their persistent nature and potential health impacts are of concern. Given the high cost of collecting serum samples, this study is to understand whether we can quantify PFC se...

A New Approach To Selectively Identify And Quantify Perfluorochemicals In Complex Matrices Using Ion Trap Time-Of-Flight Mass Spectrometry

EPA Science Inventory

Most of the published studies focusing on the environmental and biological distribution of perfluorinated alkyl compounds (PFCs) have used triple quadrupole mass spectrometers for compound identification and quantitation. Multiple-reaction-monitoring (MRM) is a sensitive mass sp...

Quantitative Determination of Perfluorochemicals and Fluorotelomer Alcohols in Plants from Biosolid-Amended Fields using LC/MS/MS and GC/MS

EPA Science Inventory

Analytical methods for determining perfluorochemicals (PFCs) and fluorotelomer alcohols (FTOHs) in plants using liquid chromatography/tandem mass spectrometry (LC/MS/MS) and gas chromatography/mass spectrometry (GC/MS) were developed, and applied to quantify a suite of analytes i...

Perfluorinated Chemicals in Surface Waters and Sediments from Northwest Georgia, USA, and Their Bioaccumulation in Lumbriculus variegatus

EPA Science Inventory

Concentrations of perfluorinated chemicals (PFCs) were measured in surface waters and sediments from the Coosa River watershed in northwest Georgia, USA, to examine their distribution downstream of a suspected source. Samples from eight sites were analyzed using liquid chromatogr...

Depth Structure from Asymmetric Shading Supports Face Discrimination

PubMed Central

Chen, Chien-Chung; Chen, Chin-Mei; Tyler, Christopher W.

2013-01-01

To examine the effect of illumination direction on the ability of observers to discriminate between faces, we manipulated the direction of illumination on scanned 3D face models. In order to dissociate the surface reflectance and illumination components of front-view face images, we introduce a symmetry algorithm that can separate the symmetric and asymmetric components of the face in both low and high spatial frequency bands. Based on this approach, hybrid faces stimuli were constructed with different combinations of symmetric and asymmetric spatial content. Discrimination results with these images showed that asymmetric illumination information biased face perception toward the structure of the shading component, while the symmetric illumination information had little, if any, effect. Measures of perceived depth showed that this property increased systematically with the asymmetric but not the symmetric low spatial frequency component. Together, these results suggest that (1) the asymmetric 3D shading information dramatically affects both the perceived facial information and the perceived depth of the facial structure; and (2) these effects both increase as the illumination direction is shifted to the side. Thus, our results support the hypothesis that face processing has a strong 3D component. PMID:23457484

Screening of perfluorinated compounds in water, sediment and biota of the Llobregat River basin (NE Spain)

NASA Astrophysics Data System (ADS)

Campo, Julian; Perez, Francisca; Pico, Yolanda; Farre, Marinella; Barcelo, Damia; Andreu, Vicente

2014-05-01

PFCs present significant thermal and chemical stability being persistent in the environment, where they can bio-accumulate and adversely affect humans and wildlife (Llorca et al., 2012). Human exposure to PFCs is of concern since PFCs tend to be associated with fatty acid binding proteins in the liver or albumin proteins in blood, and have been detected in human serum, urine, saliva, seminal plasma and breast milk (Sundstrom et al., 2011). This study is aimed at the screening of 21 perfluorinated compounds (PFCs) in environmental samples by high-performance liquid chromatography tandem mass spectrometry (LC-MS/MS). The main objective is to identify target compounds at low levels in water, sediments and biota of the Llobregat River (2010), second longest river in Catalonia and one of Barcelona's major drinking water resources. PFCs were extracted from water samples by Solid Phase Extraction (SPE); from sediment by ultrasonication with acidified methanol followed by an off-line SPE procedure (Picó et al., 2012), and from biota (fish) with alkaline digestion, clean-up by TurboFlow™ on line technology coupled to LC-MS/MS (Llorca et al., 2012). The limits of detection (LODs) and limits of quantification (LOQs) of the method were calculated by analysis of spiked river water, sediment, and biota with minimum concentrations of each individual compound at a signal-to-noise ratio of 3 and 10, respectively. The LODs and LOQs of the method in river water ranged between 0.004 and 0.8 ng L-1 and between 0.01 and 2 ng L-1, respectively. In sediment LODs were 0.013-2.667 ng g-1 dry weight (dw) and LOQs were 0.04-8 ng g-1 dw, meanwhile in biota these were 0.006-0.7 pg μL-1 and 0.02-2.26 pg μL-1, respectively. Recoveries ranged between 65% and 102% for all target compounds. The method was applied to study the spatial distribution of these compounds in the Llobregat River basin. For this, a total of 40 samples were analysed (14 water, 14 sediments, 12 fishes). Of the 21 target compounds, 13 were identified in water samples (PFBA, PFDA, PFHpA, PFHxA, PFHxDA, PFNA, PFOA, PFPeA, PFTrDA, PFUdA, L-PFBS, L-PFHxS and L-PFOS), and their concentrations ranged between 0. 1 ng L-1 (PFNA) and 2709 ng L-1 (L-PFOS). Similarly, PFBA, PFDA, PFDoA, PFHpA, PFNA, PFOA, PFPeA, PFTrDA, PFUdA, L-PFBS, L-PFHxS, L-PFOS and PFOSA were identified in sediments samples, with concentrations ranging from 0.147 ng g-1 dw (L-PFOS) to 13 ng g-1 dw (PFBA). In biota similar PFC were detected, with values between 0.03 and 1738.06 ng g-1. According to this study, PFCs were detected in different compartments of the ecosystem where they are bio-accumulating and, potentially, would produce adverse effects on humans. Acknowledgements This work has been supported by the Spanish Ministry of Economy and Competitiveness through the projects Consolider-Ingenio 2010 CSD2009-00065 and CGL2011-29703-C02-02. We also thank the persons of IDAEA for taking the samples. References Llorca, M., Farre, M., Pico, Y., Muller, J., Knepper, T. P., Barcelo, D., 2012. Analysis of perfluoroalkyl substances in waters from Germany and Spain. Sci. Total Environ. 431, 139-150. Llorca, M., Pérez, F., Farre, M., Agramunt, S., Kogevinas, M., Barceló, D., 2012. Analysis of perfluoroalkyl substances in cord blood by turbulent flow chromatography coupled to tandem mass spectrometry. Sci. Total Environ. 433, 151-160. Pico, Y., Blasco, C., Farre, M., Barcelo, D., 2012. Occurrence of perfluorinated compounds in water and sediment of L'Albufera Natural Park (Valencia, Spain). Environ.Sci.Pollut.Res. 19, 946-957. Sundstrom, M., Ehresman, D. J., Bignert, A., Butenhoff, J. L., Olsen, G. W., Chang, S. C., Bergman, A., 2011. A temporal trend study (1972-2008) of perfluorooctanesulfonate, perfluorohexanesulfonate, and perfluorooctanoate in pooled human milk samples from Stockholm, Sweden. Environ. Inter. 37, 178-183.

Characterization of the mutual influence of Ion Cyclotron and Lower Hybrid Range of frequencies systems on EAST

NASA Astrophysics Data System (ADS)

Urbanczyk, Guillaume; Zhang, Xinjun; Qin, Chengming; Zhao, Yanping; Zhang, Tao; Zhang, Ling; Li, Jiangang; Yuan, Shuai; Chen, Liang; Zhang, Heng; Zhang, Jiahui; Wang, Jianhua; Yang, Xiuda; Qian, Jinping

2017-10-01

Waves in the Ion Cyclotron (ICRF) and Lower Hybrid (LH) Range of Frequencies are efficient techniques respectively to heat the plasma and drive current. Main difficulties come from a trade-off between good RF coupling and acceptable level of impurities release. The mutual influence of both systems makes such equilibrium often hard to reach [1]. In order to investigate those interactions based on Scrape-Off Layer (SOL) plasma parameters, a new reciprocating probe was designed allying a three tips Langmuir probe with an emissive wire. The emissive filament provides a precise measure of plasma potential [2], which can be used to calibrate Langmuir probe's results. This paper reports on experimental results obtained on EAST, where there are two ICRF antennas and two LH launchers. Among others diagnostics, the new reciprocating probe enabled to evidence the deleterious influence of ICRF power on LHWs coupling in L-mode plasmas. In areas connected with an active ICRF antenna, SOL potentials increase while densities tend to decrease, respectively enhancing impurities release and deteriorating LHWs coupling. This phenomenon has mostly been attributed to RF sheath; the one that forms on top of Plasma Facing Components (PFCs) and causes ExB density convections [3]. From those experiments it seems ICRF has a strong influence on magnetically connected areas, both in the near field - influencing ICRF waves coupling - and in farther locations such as in front of LH grills. Moreover, influence of ICRF on LH system was observed both in L and H modes. Those results are consistent with RF sheath rectification process. Concerning the influence of LHWs on ICRF coupling, nothing was observed in L-mode. Besides during H-mode experiments, LHWs have been identified as having a mitigating effect on ELMs [4], which on average lowers the pedestal, increasing edge densities to the profit of ICRF waves coupling.

The effect of low energy helium ion irradiation on tungsten-tantalum (W-Ta) alloys under fusion relevant conditions

NASA Astrophysics Data System (ADS)

Gonderman, S.; Tripathi, J. K.; Novakowski, T. J.; Sizyuk, T.; Hassanein, A.

2017-08-01

Currently, tungsten remains the best candidate for plasma-facing components (PFCs) for future fusion devices because of its high melting point, low erosion, and strong mechanical properties. However, continued investigation has shown tungsten to undergo severe morphology changes under fusion-like conditions. These results motivate the study of innovative PFC materials which are resistant to surface morphology evolution. The goal of this work is to examine tungsten-tantalum (W-Ta) alloys, a potential PFC material, and their response to low energy helium ion irradiation. Specifically, W-Ta samples are exposed to 100 eV helium irradiations with a flux of 1.15 × 1021 ions m-2 s-1, at 873 K, 1023 K, and 1173 K for 1 h duration. Scanning electron microscopy (SEM) reveals significant changes in surface deterioration due to helium ion irradiation as a function of both temperature and tantalum concentration in W-Ta samples. X-Ray Diffraction (XRD) studies show a slight lattice parameter expansion in W-Ta alloy samples compared to pure W samples. The observed lattice parameter expansion in W-Ta alloy samples (proportional to increasing Ta wt.% concentrations) reflect significant differences observed in the evolution of surface morphology, i.e., fuzz development processes for both increasing Ta wt.% concentration and target temperature. These results suggest a correlation between the observed morphology differences and the induced crystal structure change caused by the presence of tantalum. Shifts in the XRD peaks before and after 100 eV helium irradiation with a flux of 1.15 × 1021 ions m-2 s-1, 1023 K, for 1 h showed a significant difference in the magnitude of the shift. This has suggested a possible link between the atomic spacing of the material and the accumulated damage. Ongoing research is needed on W-Ta alloys and other innovative materials for their application as irradiation resistant materials in future fusion or irradiation environments.

The ins and outs of modelling vertical displacement events

NASA Astrophysics Data System (ADS)

Pfefferle, David

2017-10-01

Of the many reasons a plasma discharge disrupts, Vertical Displacement Events (VDEs) lead to the most severe forces and stresses on the vacuum vessel and Plasma Facing Components (PFCs). After loss of positional control, the plasma column drifts across the vacuum vessel and comes in contact with the first wall, at which point the stored magnetic and thermal energy is abruptly released. The vessel forces have been extensively modelled in 2D but, with the constraint of axisymmetry, the fundamental 3D effects that lead to toroidal peaking, sideways forces, field-line stochastisation and halo current rotation have been vastly overlooked. In this work, we present the main results of an intense VDE modelling activity using the implicit 3D extended MHD code M3D-C1 and share our experience with the multi-domain and highly non-linear physics encountered. At the culmination of code development by the M3D-C1 group over the last decade, highlighted by the inclusion of a finite-thickness resistive vacuum vessel within the computational domain, a series of fully 3D non-linear simulations are performed using realistic transport coefficients based on the reconstruction of so-called NSTX frozen VDEs, where the feedback control was purposely switched off to trigger a vertical instability. The vertical drift phase, the evolution of the current quench and the onset of 3D halo/eddy currents are diagnosed and investigated in detail. The sensitivity of the current quench to parameter changes is assessed via 2D non-linear runs. The growth of individual toroidal modes is monitored via linear-complex runs. The intricate evolution of the plasma, which is decaying to large extent in force-balance with induced halo/wall currents, is carefully resolved via 3D non-linear runs. The location, amplitude and rotation of normal currents and wall forces are analysed and compared with experimental traces.

Aging effects on selective attention-related electroencephalographic patterns during face encoding.

PubMed

Deiber, M-P; Rodriguez, C; Jaques, D; Missonnier, P; Emch, J; Millet, P; Gold, G; Giannakopoulos, P; Ibañez, V

2010-11-24

Previous electrophysiological studies revealed that human faces elicit an early visual event-related potential (ERP) within the occipito-temporal cortex, the N170 component. Although face perception has been proposed to rely on automatic processing, the impact of selective attention on N170 remains controversial both in young and elderly individuals. Using early visual ERP and alpha power analysis, we assessed the influence of aging on selective attention to faces during delayed-recognition tasks for face and letter stimuli, examining 36 elderly and 20 young adults with preserved cognition. Face recognition performance worsened with age. Aging induced a latency delay of the N1 component for faces and letters, as well as of the face N170 component. Contrasting with letters, ignored faces elicited larger N1 and N170 components than attended faces in both age groups. This counterintuitive attention effect on face processing persisted when scenes replaced letters. In contrast with young, elderly subjects failed to suppress irrelevant letters when attending faces. Whereas attended stimuli induced a parietal alpha band desynchronization within 300-1000 ms post-stimulus with bilateral-to-right distribution for faces and left lateralization for letters, ignored and passively viewed stimuli elicited a central alpha synchronization larger on the right hemisphere. Aging delayed the latency of this alpha synchronization for both face and letter stimuli, and reduced its amplitude for ignored letters. These results suggest that due to their social relevance, human faces may cause paradoxical attention effects on early visual ERP components, but they still undergo classical top-down control as a function of endogenous selective attention. Aging does not affect the face bottom-up alerting mechanism but reduces the top-down suppression of distracting letters, possibly impinging upon face recognition, and more generally delays the top-down suppression of task-irrelevant information. Copyright © 2010 IBRO. Published by Elsevier Ltd. All rights reserved.

Comparing Online to Face-To-Face Delivery of Undergraduate Digital Circuits Content

ERIC Educational Resources Information Center

LaMeres, Brock J.; Plumb, Carolyn

2014-01-01

This paper presents a comparison of online to traditional face-to-face delivery of undergraduate digital systems material. Two specific components of digital content were compared and evaluated: a sophomore logic circuits course with no laboratory, and a microprocessor laboratory component of a junior-level computer systems course. For each of…

Power-Factor Controllers: How Safe?

NASA Technical Reports Server (NTRS)

Long, K.; Christian, W.; Kovacik, J.; Grazyk, T.

1985-01-01

Potential safety problems with power-factor controllers (PFC's) evaluated. Based on study of PFCs in use with appliances, report recommends measures to prevent consumers from misapplying these energy saving devices. Device used on such appliances as refrigerators, sewing machines, pumps, hair dryers, and food processors. When misused, they fail to save energy and may cause damage.

Heavy Lift Helicopter - Prototype Technical Summary

DTIC Science & Technology

1980-04-01

in an inte- grated design. The following paragraphs discuss the swash - plate actuator servo loops and provide details...instrumentation in the prototype aircraft. Development testing of the flight control module in conjunc- tion with the transmission-driven pump and the reservoir was...PFCS employed cockpit controllers and force-feel actuation developed in the ATC

Polyfluoroalkyl Chemicals and Learning and Developmental Disorders: Epidemiology and Exposure Assessment

ERIC Educational Resources Information Center

Hoffman, Jennifer Kate

2010-01-01

This dissertation has two areas of focus: learning and developmental disorders (LDDs) and polyfluoroalkyl chemicals (PFCs). Epidemiological and exposure assessment methods are applied to each. The first paper used geographic location as a surrogate for exposure and broadly assesses the effect of the environment, both physical and social, on LDD…

Spatial and Temporal Patterns in Concentrations of Perfluorinated Compounds in Bald Eagle Nestlings in the Upper Midwestern United States

EPA Science Inventory

Perfluorinated chemicals (PFCs) are of concern due to their widespread use, persistence in the environment, tendency to accumulate in animal tissues, and growing evidence of toxicity. Between 2006 and 2011 we collected blood plasma from 261 bald eagle nestlings in six study areas...

An Assessment of the Exposure of Americans to Perflourooctane Sulfonate: A Comparison of Estimated Intake with Values Inferred from NHANES Data

EPA Science Inventory

To better understand human exposure to perfluorinated compounds (PFCs), a model that assesses exposure to perfluorooctane sulfonate (PFOS) and its precursors from both an intake and a body burden perspective and combines the two with a simple pharmacokinetic (PK) model is demonst...

Total fluorine, extractable organic fluorine, perfluorooctane sulfonate and other related fluorochemicals in liver of Indo-Pacific humpback dolphins (Sousa chinensis) and finless porpoises (Neophocaena phocaenoides) from South China.

PubMed

Yeung, L W Y; Miyake, Y; Wang, Y; Taniyasu, S; Yamashita, N; Lam, P K S

2009-01-01

The concentrations of 10 PFCs (perfluorinated compounds: PFOS, PFHxS, PFOSA, N-EtFOSA, PFDoDA, PFUnDA, PFDA, PFNA, PFOA, and PFHpA) were measured in liver samples of Indo-Pacific humpback dolphins (Sousa chinensis) (n=10) and finless porpoises (Neophocaena phocaenoides) (n=10) stranded in Hong Kong between 2003 and 2007. PFOS was the dominant PFC in the tissues at concentrations ranging at 26-693 ng/g ww in dolphins and 51.3-262 ng/g ww in porpoises. A newly developed combustion ion chromatography for fluorine was applied to measure total fluorine (TF) and extractable organic fluorine (EOF) in these liver samples to understand PFC contamination using the concept of mass balance analysis. Comparisons between the amounts of known PFCs and EOF in the livers showed that a large proportion (approximately 70%) of the organic fluorine in both species is of unknown origin. These investigations are critical for a comprehensive assessment of the risks of these compounds to humans and other receptors.

Neuromagnetic evidence that the right fusiform face area is essential for human face awareness: An intermittent binocular rivalry study.

PubMed

Kume, Yuko; Maekawa, Toshihiko; Urakawa, Tomokazu; Hironaga, Naruhito; Ogata, Katsuya; Shigyo, Maki; Tobimatsu, Shozo

2016-08-01

When and where the awareness of faces is consciously initiated is unclear. We used magnetoencephalography to probe the brain responses associated with face awareness under intermittent pseudo-rivalry (PR) and binocular rivalry (BR) conditions. The stimuli comprised three pictures: a human face, a monkey face and a house. In the PR condition, we detected the M130 component, which has been minimally characterized in previous research. We obtained a clear recording of the M170 component in the fusiform face area (FFA), and found that this component had an earlier response time to faces compared with other objects. The M170 occurred predominantly in the right hemisphere in both conditions. In the BR condition, the amplitude of the M130 significantly increased in the right hemisphere irrespective of the physical characteristics of the visual stimuli. Conversely, we did not detect the M170 when the face image was suppressed in the BR condition, although this component was clearly present when awareness for the face was initiated. We also found a significant difference in the latency of the M170 (human

Different brain activations between own- and other-race face categorization: an fMRI study using group independent component analysis

NASA Astrophysics Data System (ADS)

Wei, Wenjuan; Liu, Jiangang; Dai, Ruwei; Feng, Lu; Li, Ling; Tian, Jie

2014-03-01

Previous behavioral research has proved that individuals process own- and other-race faces differently. One well-known effect is the other-race effect (ORE), which indicates that individuals categorize other-race faces more accurately and faster than own-race faces. The existed functional magnetic resonance imaging (fMRI) studies of the other-race effect mainly focused on the racial prejudice and the socio-affective differences towards own- and other-race face. In the present fMRI study, we adopted a race-categorization task to determine the activation level differences between categorizing own- and other-race faces. Thirty one Chinese participants who live in China with Chinese as the majority and who had no direct contact with Caucasian individual were recruited in the present study. We used the group independent component analysis (ICA), which is a method of blind source signal separation that has proven to be promising for analysis of fMRI data. We separated the entail data into 56 components which is estimated based on one subject using the Minimal Description Length (MDL) criteria. The components sorted based on the multiple linear regression temporal sorting criteria, and the fit regression parameters were used in performing statistical test to evaluate the task-relatedness of the components. The one way anova was performed to test the significance of the component time course in different conditions. Our result showed that the areas, which coordinates is similar to the right FFA coordinates that previous studies reported, were greater activated for own-race faces than other-race faces, while the precuneus showed greater activation for other-race faces than own-race faces.

Determining if Space is an Applicable Component to Intelligence Preparation of the Battlefield for Ranger Operations When Facing Non-Nation-State Adversaries

DTIC Science & Technology

2002-05-31

DETERMINING IF SPACE IS AN APPLICABLE COMPONENT TO INTELLIGENCE PREPARATION OF THE BATTLEFIELD FOR RANGER OPERATIONS WHEN FACING NON-NATION-STATE...Candidate: Major Michael Bruce Johnson Thesis Title: Determining if Space is an Applicable Component to Intelligence Preparation of the Battlefield for ...iii ABSTRACT DETERMINING IF SPACE IS AN APPLICABLE COMPONENT TO INTELLIGENCE PREPARATION OF THE BATTLEFIELD FOR RANGER OPERATIONS WHEN FACING NON

Wavelet decomposition based principal component analysis for face recognition using MATLAB

NASA Astrophysics Data System (ADS)

Sharma, Mahesh Kumar; Sharma, Shashikant; Leeprechanon, Nopbhorn; Ranjan, Aashish

2016-03-01

For the realization of face recognition systems in the static as well as in the real time frame, algorithms such as principal component analysis, independent component analysis, linear discriminate analysis, neural networks and genetic algorithms are used for decades. This paper discusses an approach which is a wavelet decomposition based principal component analysis for face recognition. Principal component analysis is chosen over other algorithms due to its relative simplicity, efficiency, and robustness features. The term face recognition stands for identifying a person from his facial gestures and having resemblance with factor analysis in some sense, i.e. extraction of the principal component of an image. Principal component analysis is subjected to some drawbacks, mainly the poor discriminatory power and the large computational load in finding eigenvectors, in particular. These drawbacks can be greatly reduced by combining both wavelet transform decomposition for feature extraction and principal component analysis for pattern representation and classification together, by analyzing the facial gestures into space and time domain, where, frequency and time are used interchangeably. From the experimental results, it is envisaged that this face recognition method has made a significant percentage improvement in recognition rate as well as having a better computational efficiency.

InterFace: A software package for face image warping, averaging, and principal components analysis.

PubMed

Kramer, Robin S S; Jenkins, Rob; Burton, A Mike

2017-12-01

We describe InterFace, a software package for research in face recognition. The package supports image warping, reshaping, averaging of multiple face images, and morphing between faces. It also supports principal components analysis (PCA) of face images, along with tools for exploring the "face space" produced by PCA. The package uses a simple graphical user interface, allowing users to perform these sophisticated image manipulations without any need for programming knowledge. The program is available for download in the form of an app, which requires that users also have access to the (freely available) MATLAB Runtime environment.

Brain Functional Changes before, during, and after Clinical Pain.

PubMed

Hu, X; Racek, A J; Bellile, E; Nascimento, T D; Bender, M C; Toback, R L; Burnett, D; Khatib, L; McMahan, R; Kovelman, I; Ellwood, R P; DaSilva, A F

2018-05-01

This study used an emerging brain imaging technique, functional near-infrared spectroscopy (fNIRS), to investigate functional brain activation and connectivity that modulates sometimes traumatic pain experience in a clinical setting. Hemodynamic responses were recorded at bilateral somatosensory (S1) and prefrontal cortices (PFCs) from 12 patients with dentin hypersensitivity in a dental chair before, during, and after clinical pain. Clinical dental pain was triggered with 20 consecutive descending cold stimulations (32° to 0°C) to the affected teeth. We used a partial least squares path modeling framework to link patients' clinical pain experience with recorded hemodynamic responses at sequential stages and baseline resting-state functional connectivity (RSFC). Hemodynamic responses at PFC/S1 were sequentially elicited by expectation, cold detection, and pain perception at a high-level coefficient (coefficients: 0.92, 0.98, and 0.99, P < 0.05). We found that the pain ratings were positively affected only at a moderate level of coefficients by such sequence of functional activation (coefficient: 0.52, P < 0.05) and the baseline PFC-S1 RSFC (coefficient: 0.59, P < 0.05). Furthermore, when the dental pain had finally subsided, the PFC increased its functional connection with the affected S1 orofacial region contralateral to the pain stimulus and, in contrast, decreased with the ipsilateral homuncular S1 regions ( P < 0.05). Our study indicated for the first time that patients' clinical pain experience in the dental chair can be predicted concomitantly by their baseline functional connectivity between S1 and PFC, as well as their sequence of ongoing hemodynamic responses. In addition, this linked cascade of events had immediate after-effects on the patients' brain connectivity, even when clinical pain had already ceased. Our findings offer a better understating of the ongoing impact of affective and sensory experience in the brain before, during, and after clinical dental pain.

Determination of an Effective Perfluorinated Compounds (PFCs) Oxidation Method

NASA Astrophysics Data System (ADS)

Siriwardena, D. P.; Crimi, M.; Holsen, T.; Bellona, C.

2014-12-01

Perfluoroalkyl and polyfluoroalkyl substances (PFASs) are a stable synthetic class of chemicals ubiquitously spread in environmental media (i.e. air, soil, biota, surface water and groundwater). The substances' strong polar carbon-fluorine bonds and their high thermal and chemical stability make them resistant to biological, chemical, and physical degradation. The purpose of this research is to identify the most effective oxidation method to treat perfluorinated compounds (PFCs) and their by-products that is suitable for in situ application. The laboratory oxidation study focuses on the more commonly detected and studied long-chain (C-8) PFAS; perfluorooctanoic acids (PFOA) and perfluorooctane sulfonic acid (PFOS). Existing research evaluating oxidizing treatment effectiveness on perfluoroalkyl sulfoinoic acids (PFSAs) is limited. A review of the literature and results from preliminary studies indicate that activated persulfate and catalyzed hydrogen peroxide propagation (CHP) reactions appear to be promising oxidants for PFOA. It has been demonstrated that the reactivity of superoxide in water increases in the presence of hydrogen peroxide (H2O2) and solids. Superoxide generated in CHP reactions degrades PFOA seemingly similar to superoxide-mediated destruction of the perhalogenated compounds.The goal of this study is to look at conditions that promote generation of superoxide and look at PFASs treatment effectiveness and byproduct generation. CHP reactions are conducted with varying amount of H2O2 and Fe(III) to determine the optimum conditions for PFC degradation. Results will be compared to those of another experiment using manganese dioxide as a CHP catalyst with varied H2O2 concentration to generate superoxide to degrade PFASs. Activated persulfate conditions to be compared include alkaline pH activation, heat activation, and dual oxidation (combined H2O2 and persulfate ). This presentation will focus on a comparison of oxidation effectiveness under the varied reaction conditions as well as on the oxidation intermediates and byproducts generated toward improved understanding of the potential for and limitations of in situ chemical oxidation (ISCO) for treatment of PFCs.

Environmentally benign semiconductor processing for dielectric etch

NASA Astrophysics Data System (ADS)

Liao, Marci Yi-Ting

Semiconductor processing requires intensive usage of chemicals, electricity, and water. Such intensive resource usage leaves a large impact on the environment. For instance, in Silicon Valley, the semiconductor industry is responsible for 80% of the hazardous waste sites contaminated enough to require government assistance. Research on environmentally benign semiconductor processing is needed to reduce the environmental impact of the semiconductor industry. The focus of this dissertation is on the environmental impact of one aspect of semiconductor processing: patterning of dielectric materials. Plasma etching of silicon dioxide emits perfluorocarbons (PFCs) gases, like C2F6 and CF4, into the atmosphere. These gases are super global warming/greenhouse gases because of their extremely long atmospheric lifetimes and excellent infrared absorption properties. We developed the first inductively coupled plasma (ICP) abatement device for destroying PFCs downstream of a plasma etcher. Destruction efficiencies of 99% and 94% can be obtained for the above mentioned PFCs, by using O 2 as an additive gas. Our results have lead to extensive modeling in academia as well as commercialization of the ICP abatement system. Dielectric patterning of hi-k materials for future device technology brings different environment challenges. The uncertainty of the hi-k material selection and the patterning method need to be addressed. We have evaluated the environmental impact of three different dielectric patterning methods (plasma etch, wet etch and chemical-mechanical polishing), as well as, the transistor device performances associated with the patterning methods. Plasma etching was found to be the most environmentally benign patterning method, which also gives the best device performance. However, the environmental concern for plasma etching is the possibility of cross-contamination from low volatility etch by-products. Therefore, mass transfer in a plasma etcher for a promising hi-k dielectric material, ZrO2, was studied. A novel cross-contamination sampling technique was developed, along with a mass transfer model.

Perfluorinated Compounds, Polychlorinated Biphenyls, and Organochlorine Pesticide Contamination in Composite Food Samples from Dallas, Texas, USA

PubMed Central

Schecter, Arnold; Colacino, Justin; Haffner, Darrah; Patel, Keyur; Opel, Matthias; Päpke, Olaf; Birnbaum, Linda

2010-01-01

Objectives The objective of this article is to extend our previous studies of persistent organic pollutant (POP) contamination of U.S. food by measuring perfluorinated compounds (PFCs), organochlorine pesticides, and polychlorinated biphenyls (PCBs) in composite food samples. This study is part of a larger study reported in two articles, the other of which reports levels of polybrominated diphenyl ethers and hexabromocyclododecane brominated flame retardants in these composite foods [Schecter et al. 2010. Polybrominated diphenyl ethers (PBDEs) and hexabromocyclodecane (HBCD) in composite U.S. food samples, Environ Health Perspect 118:357–362]. Methods In this study we measured concentrations of 32 organochlorine pesticides, 7 PCBs, and 11 PFCs in composite samples of 31 different types of food (310 individual food samples) purchased from supermarkets in Dallas, Texas (USA), in 2009. Dietary intake of these chemicals was calculated for an average American. Results Contamination varied greatly among chemical and food types. The highest level of pesticide contamination was from the dichlorodiphenyltrichloroethane (DDT) metabolite p,p′- dichlorodiphenyldichloroethylene, which ranged from 0.028 ng/g wet weight (ww) in whole milk yogurt to 2.3 ng/g ww in catfish fillets. We found PCB congeners (28, 52, 101, 118, 138, 153, and 180) primarily in fish, with highest levels in salmon (PCB-153, 1.2 ng/g ww; PCB-138, 0.93 ng/g ww). For PFCs, we detected perfluorooctanoic acid (PFOA) in 17 of 31 samples, ranging from 0.07 ng/g in potatoes to 1.80 ng/g in olive oil. In terms of dietary intake, DDT and DDT metabolites, endosulfans, aldrin, PCBs, and PFOA were consumed at the highest levels. Conclusion Despite product bans, we found POPs in U.S. food, and mixtures of these chemicals are consumed by the American public at varying levels. This suggests the need to expand testing of food for chemical contaminants. PMID:20146964

Do perfluoroalkyl substances affect metabolic function and plasma lipids?--Analysis of the 2007-2009, Canadian Health Measures Survey (CHMS) Cycle 1.

PubMed

Fisher, Mandy; Arbuckle, Tye E; Wade, Mike; Haines, Douglas A

2013-02-01

Perfluorinated compounds (PFCs) are man-made chemicals that are heat stable, non-flammable and able to repel both water and oils. Biomonitoring research shows global distribution in human, animal and aquatic environments of these chemicals. PFCs have been shown to activate the peroxisome proliferator-activated receptors which play a large role in metabolism and the regulation of energy homeostasis. Previous epidemiological research has also suggested a potential role of PFCs on lipid and glucose metabolism. The objectives of this study were to examine the association between the levels of perfluorinated compounds perfluorooctane sulfonate (PFOS), perfluorooctanoic acid (PFOA), and perfluorohexane sulfonate (PFHxS) in plasma and metabolic function and plasma lipid levels. Using cross-sectional data from the Canadian Health Measures Survey (Cycle 1 2007-2009) we examined the association in adults between plasma levels of PFOA, PFOS and PFHxS (n=2700) on cholesterol outcomes, metabolic syndrome and glucose homeostasis using multivariate linear and logistic regression models. We found some evidence of a significant association between perfluoroalkyl substances, notably PFHxS, with total cholesterol (TC), low-density lipoprotein cholesterol (LDL), total cholesterol/high density lipoprotein cholesterol ratio (TC/HDL) and non-HDL cholesterol as well as an elevated odds of high cholesterol. We found some associations with PFOA and PFOS in our unweighted models but these results did not remain significant after weighting for sampling strategy. We found no association with metabolic syndrome, or glucose homeostasis parameters. This study showed lower levels of PFOA and PFOS and slightly higher levels of PFHxS than other published population studies. Our results did not give significant evidence to support the association with cholesterol outcomes with PFOS and PFOA. However, we did observe several significant associations with the PFHxS and cholesterol outcomes (LDL, TC, NON-HDL, TC/HDL ratio). Crown Copyright © 2012. Published by Elsevier Inc. All rights reserved.

Transient induced tungsten melting at the Joint European Torus (JET)

NASA Astrophysics Data System (ADS)

Coenen, J. W.; Matthews, G. F.; Krieger, K.; Iglesias, D.; Bunting, P.; Corre, Y.; Silburn, S.; Balboa, I.; Bazylev, B.; Conway, N.; Coffey, I.; Dejarnac, R.; Gauthier, E.; Gaspar, J.; Jachmich, S.; Jepu, I.; Makepeace, C.; Scannell, R.; Stamp, M.; Petersson, P.; Pitts, R. A.; Wiesen, S.; Widdowson, A.; Heinola, K.; Baron-Wiechec, A.; Contributors, JET

2017-12-01

Melting is one of the major risks associated with tungsten (W) plasma-facing components (PFCs) in tokamaks like JET or ITER. These components are designed such that leading edges and hence excessive plasma heat loads deposited at near normal incidence are avoided. Due to the high stored energies in ITER discharges, shallow surface melting can occur under insufficiently mitigated plasma disruption and so-called edge localised modes—power load transients. A dedicated program was carried out at the JET to study the physics and consequences of W transient melting. Following initial exposures in 2013 (ILW-1) of a W-lamella with leading edge, new experiments have been performed on a sloped surface (15{}\\circ slope) during the 2015/2016 (ILW-3) campaign. This new experiment allows significantly improved infrared thermography measurements and thus resolved important issue of power loading in the context of the previous leading edge exposures. The new lamella was monitored by local diagnostics: spectroscopy, thermography and high-resolution photography in between discharges. No impact on the main plasma was observed despite a strong increase of the local W source consistent with evaporation. In contrast to the earlier exposure, no droplet emission was observed from the sloped surface. Topological modifications resulting from the melting are clearly visible between discharges on the photographic images. Melt damage can be clearly linked to the infrared measurements: the emissivity drops in zones where melting occurs. In comparison with the previous leading edge experiment, no runaway melt motion is observed, consistent with the hypothesis that the escape of thermionic electrons emitted from the melt zone is largely suppressed in this geometry, where the magnetic field intersects the surface at lower angles than in the case of perpendicular impact on a leading edge. Utilising both exposures allows us to further test the model of the forces driving melt motion that successfully reproduced the findings from the original leading edge exposure. Since the ILW-1 experiments, the exposed misaligned lamella has now been retrieved from the JET machine and post mortem analysis has been performed. No obvious mass loss is observed. Profilometry of the ILW-1 lamella shows the structure of the melt damage which is in line with the modell predictions thus allowing further model validation. Nuclear reaction analysis shows a tenfold reduction in surface deuterium concentration in the molten surface in comparison to the non-molten part of the lamella.

Ambient mixing ratios of atmospheric halogenated compounds at five background stations in China

NASA Astrophysics Data System (ADS)

Zhang, Gen; Yao, Bo; Vollmer, Martin K.; Montzka, Stephen A.; Mühle, Jens; Weiss, Ray F.; O'Doherty, Simon; Li, Yi; Fang, Shuangxi; Reimann, Stefan

2017-07-01

High precision measurements of three chlorofluorocarbons (CFCs), three hydrochlorofluorocarbons (HCFCs), six hydrofluorocarbons (HFCs), three perfluorocarbons (PFCs), and sulfur hexafluoride (SF6) were made at five Chinese background stations from January 2011 to December 2012. Their station means in the background air were 239.5 ± 0.69 parts-per-trillion dry-air mole fraction mixing ratios (ppt) for CFC-11, 536.5 ± 1.49 ppt for CFC-12, 74.66 ± 0.09 ppt for CFC-113, 232.1 ± 4.77 ppt for HCFC-22, 23.78 ± 0.29 ppt for HCFC-141b, 22.92 ± 0.42 ppt for HCFC-142b, 11.75 ± 0.43 ppt for HFC-125, 71.32 ± 1.35 ppt for HFC-134a, 13.62 ± 0.43 ppt for HFC-143a, 9.10 ± 1.26 ppt for HFC-152a, 25.45 ± 0.1 ppt for HFC-23, 7.28 ± 0.48 ppt for HFC-32, 4.32 ± 0.03 ppt for PFC-116, 0.63 ± 0.04 ppt for PFC-218, 1.36 ± 0.01 ppt for PFC-318, and 7.67 ± 0.03 ppt for SF6, respectively, which were comparable with those measured at the two Northern Hemisphere (NH) AGAGE stations: Mace Head, Ireland (MHD) and Trinidad Head, California, USA (THD). Compared with our results for earlier years from in-situ measurement at SDZ, background-air mixing ratios of CFCs are now declining, while those for HCFCs, HFCs, PFCs, and SF6 are still increasing. The ratios of the number of sampling events in which measured mixing ratios were elevated above background (pollution events) relative to the total sample frequency (POL/SUM) for CFCs, HCFCs, and HFCs were found to be station dependent, generally LAN > SDZ > LFS > XGL > WLG. The enhancement (△, polluted mixing ratios minus background mixing ratios) generally show distinct patterns, with HCFCs (40.7-175.4 ppt) > HFCs (15.8-66.3 ppt)> CFCs (15.8-33.8 ppt)> PFCs (0.1-0.9 ppt) at five stations, especially for HCFC-22 ranging from 36.9 ppt to 138.2 ppt. Combining with the molecular weights, our findings imply biggest emissions of HCFCs in the regions around these Chinese sites compared to HFCs and CFCs, while the smallest of PFCs, consistent with CFCs being phased out and replaced with HCFCs in China. In addition, relative emission strengths (emission was expressed by mole fractions) of these halocarbons in China were inferred as HCFC-22 > HCFC-141b > HFC-134a > HCFC-142b for the Yangtze River Delta (YRD) and as HCFC-22 > HCFC-142b > HCFC-141b ≈ HFC-134a in the North China Plain (NCP).

Processing of Fear and Anger Facial Expressions: The Role of Spatial Frequency

PubMed Central

Comfort, William E.; Wang, Meng; Benton, Christopher P.; Zana, Yossi

2013-01-01

Spatial frequency (SF) components encode a portion of the affective value expressed in face images. The aim of this study was to estimate the relative weight of specific frequency spectrum bandwidth on the discrimination of anger and fear facial expressions. The general paradigm was a classification of the expression of faces morphed at varying proportions between anger and fear images in which SF adaptation and SF subtraction are expected to shift classification of facial emotion. A series of three experiments was conducted. In Experiment 1 subjects classified morphed face images that were unfiltered or filtered to remove either low (<8 cycles/face), middle (12–28 cycles/face), or high (>32 cycles/face) SF components. In Experiment 2 subjects were adapted to unfiltered or filtered prototypical (non-morphed) fear face images and subsequently classified morphed face images. In Experiment 3 subjects were adapted to unfiltered or filtered prototypical fear face images with the phase component randomized before classifying morphed face images. Removing mid frequency components from the target images shifted classification toward fear. The same shift was observed under adaptation condition to unfiltered and low- and middle-range filtered fear images. However, when the phase spectrum of the same adaptation stimuli was randomized, no adaptation effect was observed. These results suggest that medium SF components support the perception of fear more than anger at both low and high level of processing. They also suggest that the effect at high-level processing stage is related more to high-level featural and/or configural information than to the low-level frequency spectrum. PMID:23637687

Blending Online Components into Traditional Instruction in Pre-Service Teacher Education: The Good, the Bad, and the Ugly

ERIC Educational Resources Information Center

Lin, Hong

2008-01-01

This study investigated the effectiveness of using online instruction as a supplement to a face-to-face introductory technology education course. Survey data were collected from 46 pre-service teachers. Findings indicated that when traditional face-to-face instruction was combined with online components, learning was enhanced over a single…

Contribution of Wastewater Treatment Plants to Concentrations of PBDEs, PFCs, PCBs, DDT and Synthetic Musks in Fish Tissue from U.S. Urban Waters

EPA Science Inventory

Wastewater treatment plants (WWTPs) are tasked with removing a wide variety of contaminants from influents, including BOD and nutrients from human waste as well as any and all other compounds that emanate from homes and commercial facilities in the communities they serve. Traces ...

Interaction of plasmas with lithium and tungsten fusion plasma facing components

NASA Astrophysics Data System (ADS)

Fiflis, Peter Robert

One of the largest outstanding issues in magnetic confinement fusion is the interaction of the fusion plasma with the first wall of the device; an interaction which is strongest in the divertor region. Erosion, melting, sputtering, and deformation are all concerns which inform choices of divertor material. Of the many materials proposed for use in the divertor, only a few remain as promising choices. Tungsten has been chosen as the material for the ITER divertor, and liquid lithium stands poised as its replacement in higher heat flux devices. As a refractory metal, tungsten's large melting point and thermal conductivity as well as its low sputtering yield have led to its selection as the material of choice of the ITER divertor. Experiments have reinforced this choice demonstrating tungsten's ability to withstand large heat fluxes when adequately cooled. However, tungsten has shown a propensity to nanostructure under exposure within a certain temperature range to large fluxes of helium ions. These nanostructures if disrupted into the plasma as dust by an off-normal event would cause quenching of the plasma from the generated dust. Liquid lithium, meanwhile, has gathered growing interest within the fusion community in recent years as a divertor, limiter, and alternative first wall material. Liquid lithium is attractive as a low-Z material replacement for refractory metals due to its ability to getter impurities, while also being self-healing in nature. However, concerns exist about the stability of a liquid metal surface at the edge of a fusion device. Liquid metal pools, such as the Li-DiMes probe, have shown evidence of macroscopic lithium displacement as well as droplet formation and ejection into the plasma. These issues must be mitigated in future implementations of liquid lithium divertor concepts. Rayleigh-Taylor-like (RT) and Kelvin-Helmholtz-like (KH) instabilities have been claimed as the initiators of droplet ejection, yet not enough data exists to delineate a stability boundary. The influences of plasma pressure and current driven instabilities on lithium surfaces that lead to droplet ejection are investigated to determine which of the two effects is dominant for a given set of plasma conditions. This work studies the influence of large plasma fluxes on these two materials to better inform the selection and design of plasma facing components (PFCs). The nanostructuring of tungsten was investigated to determine the mechanisms by which tungsten nanostructures so that its formation may be mitigated. Experiments investigated the dependence of nanostructuring on temperature, looked at the morphological evolution, and grew nanostructures on a variety of metals to examine their similarity to tungsten. Additionally, a computational model is presented for the initial stages of fuzz formation showing good quantitative and qualitative agreement with experimental observations. The influences of RT and KH instabilities on the surface of liquid lithium were experimentally observed and quantified on the ThermoElectric-driven Liquid-metal plasma-facing Structures (TELS) chamber at the University of Illinois at Urbana-Champaign and the stabilizing effect of surface tension, an effect employed by the LiMIT concept as well as other liquid lithium concepts, was studied, and the stability boundary afforded by surface tension was compared between experiment, computational simulation, and theory.

Subject-specific and pose-oriented facial features for face recognition across poses.

PubMed

Lee, Ping-Han; Hsu, Gee-Sern; Wang, Yun-Wen; Hung, Yi-Ping

2012-10-01

Most face recognition scenarios assume that frontal faces or mug shots are available for enrollment to the database, faces of other poses are collected in the probe set. Given a face from the probe set, one needs to determine whether a match in the database exists. This is under the assumption that in forensic applications, most suspects have their mug shots available in the database, and face recognition aims at recognizing the suspects when their faces of various poses are captured by a surveillance camera. This paper considers a different scenario: given a face with multiple poses available, which may or may not include a mug shot, develop a method to recognize the face with poses different from those captured. That is, given two disjoint sets of poses of a face, one for enrollment and the other for recognition, this paper reports a method best for handling such cases. The proposed method includes feature extraction and classification. For feature extraction, we first cluster the poses of each subject's face in the enrollment set into a few pose classes and then decompose the appearance of the face in each pose class using Embedded Hidden Markov Model, which allows us to define a set of subject-specific and pose-priented (SSPO) facial components for each subject. For classification, an Adaboost weighting scheme is used to fuse the component classifiers with SSPO component features. The proposed method is proven to outperform other approaches, including a component-based classifier with local facial features cropped manually, in an extensive performance evaluation study.

'Faceness' and affectivity: evidence for genetic contributions to distinct components of electrocortical response to human faces.

PubMed

Shannon, Robert W; Patrick, Christopher J; Venables, Noah C; He, Sheng

2013-12-01

The ability to recognize a variety of different human faces is undoubtedly one of the most important and impressive functions of the human perceptual system. Neuroimaging studies have revealed multiple brain regions (including the FFA, STS, OFA) and electrophysiological studies have identified differing brain event-related potential (ERP) components (e.g., N170, P200) possibly related to distinct types of face information processing. To evaluate the heritability of ERP components associated with face processing, including N170, P200, and LPP, we examined ERP responses to fearful and neutral face stimuli in monozygotic (MZ) and dizygotic (DZ) twins. Concordance levels for early brain response indices of face processing (N170, P200) were found to be stronger for MZ than DZ twins, providing evidence of a heritable basis to each. These findings support the idea that certain key neural mechanisms for face processing are genetically coded. Implications for understanding individual differences in recognition of facial identity and the emotional content of faces are discussed. Copyright © 2013 Elsevier Inc. All rights reserved.

A thermo-electric-driven flowing liquid lithium limiter/divertor for magnetic confined fusion

NASA Astrophysics Data System (ADS)

Ruzic, D. N.; Xu, Wenyu; Curreli, Davide; Andruczyk, Daniel; Mui, Travis

2012-10-01

The concept of using a liquid metal, especially liquid lithium, as the plasma facing surface may provide the best path forward toward reactor designs. A liquid PFC can effectively eliminate the erosion and thermal stress problems compared to the solid PFC while transferring heat and prolong the lifetime limit of the PFCs. A liquid lithium surface can also suppress the hydrogen isotopes recycling and getter the impurities in fusion reactor. The Lithium/metal infused trench (LiMIT) concept successfully proved that the thermoelectric effect can induce electric currents inside liquid lithium and an external magnetic field can drive liquid lithium to flow within metallic open trenches. IR camera and thermocouple measurements prove the strong heat transfer ability of this concept. A new flowing lithium system with active control of the temperature gradient inside the lithium trenches and back flow channels has been designed. TEMHD driven liquid lithium run steady state and pulsed for a few seconds of high heat flux (˜15MW/m^2) has been used to investigate the transient reaction of the flowing lithium. A similar tray is scheduled to be tested in HT-7, Hefei, China as a limiter in Sept. 2012. Related movies and analysis will be shown.

The Physical Properties of a Lavage Mixture of Pulmonary Surfactant, Perfluorodecaline, and Methylprednisolone (Perfactant Lavage)

DTIC Science & Technology

2014-05-09

release: distribution unlimited Purpose: To characterize the physical properties of a lavage mixture of pulmonary surfactant, perfluorocarbon and...methylprednisolone. Background: Perfluorocarbons (PFCs) are compounds derived from hydrocarbons by the substitution of hydrogen atoms with fluorine...atoms. Perfluorocarbon liquids are colorless, odorless and biologically inert. They are highly dense, due to their molecular weight. Their low

A solar light driven dual photoelectrode photocatalytic fuel cell (PFC) for simultaneous wastewater treatment and electricity generation.

PubMed

Bai, Jing; Wang, Rui; Li, Yunpo; Tang, Yuanyuan; Zeng, Qingyi; Xia, Ligang; Li, Xuejin; Li, Jinhua; Li, Caolong; Zhou, Baoxue

2016-07-05

In this paper, a novel dual heterojunction Photocatalytic Fuel Cell (PFC) system based on BiVO4/TiO2 nanotubes/FTO photoanode and ZnO/CuO nanowires/FTO photocathode has been designed. Compared with the electrodes in PFCs reported in earlier literatures, the proposed heterojunction not only enhances the visible light absorption but also offers a higher photoconversion efficiency. In addition, the nanostructured heterojunction owns a large surface area that ensures a large amount of active sites for organics degradation. The performance of the PFC base on the dual photoelectrodes was also studied herein. The results indicated that the PFC in ths paper exhibits a superior performance and its JV(max) reached 0.116 mw cm(-2), which is higher than that in most of reported PFCs with a Pt-free photocathode. When hazardous organic compounds such as methyl orange, Congo red and methylene blue were decomposed, the degradation rates obtained is to be 76%, 83%, and 90% respectively after 80 mins reaction. The proposed heterojunction photoelectrodes provided great potential for cost-effective and high-efficiency organic pollutants degradation and electricity generation in a PFC system. Copyright © 2016 Elsevier B.V. All rights reserved.

Polyfluoroalkyl chemicals in house dust

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kato, Kayoko; Calafat, Antonia M., E-mail: acalafat@cdc.gov; Needham, Larry L.

2009-07-15

We developed a high throughput analytical method using on-line solid phase extraction coupled with isotope dilution high-performance liquid chromatography-tandem mass spectrometry (on-line SPE-HPLC-MS/MS) to simultaneously determine the concentrations of 17 polyfluoroalkyl chemicals (PFCs) in house dust. The sample preparation includes dispersion of the dust samples in 0.1 M formic acid:MeOH (1:1), followed by agitation and filtration, addition of the isotope-labeled internal standard solution to the filtrate, and analysis by on-line SPE-HPLC-MS/MS. The limits of quantitation were <4.0 ng/g. The method accuracies ranged between 73.2% and 100.2% for the different analytes at two spike levels. We confirmed the validity of themore » method by analyzing 39 household dust samples collected in 2004. Of the 17 PFCs measured, 6 of them-perfluorobutane sulfonate (PFBuS), N-ethyl-perfluorooctane sulfonamide, 2-(N-ethyl-perfluorooctane sulfonamido) acetic acid (Et-PFOSA-AcOH), 2-(N-methyl-perfluorooctane sulfonamido) ethanol (Me-PFOSA-EtOH), perfluorohexane sulfonate (PFHxS), and perfluorooctane sulfonate (PFOS)-had detection frequencies >70%. We detected PFOS, PFBuS, and PFHxS at the highest median concentration, followed by Et-PFOSA-AcOH and Me-PFOSA-EtOH.« less

Rim seal arrangement having pumping feature

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lee, Ching-Pang; Myers, Caleb

A rim seal arrangement for a gas turbine engine includes a first seal face on a rotor component, and a second seal face on a stationary annular rim centered about a rotation axis of the rotor component. The second seal face is spaced from the first seal face along an axial direction to define a seal gap. The seal gap is located between a radially outer hot gas path and a radially inner rotor cavity. The first seal face has a plurality of circumferentially spaced depressions, each having a depth in an axial direction and extending along a radial extentmore » of the first seal face. The depressions influence flow in the seal gap such that during rotation of the rotor component, fluid in the seal gap is pumped in a radially outward direction to prevent ingestion of a gas path fluid from the hot gas path into the rotor cavity.« less

The face-selective N170 component is modulated by facial color.

PubMed

Nakajima, Kae; Minami, Tetsuto; Nakauchi, Shigeki

2012-08-01

Faces play an important role in social interaction by conveying information and emotion. Of the various components of the face, color particularly provides important clues with regard to perception of age, sex, health status, and attractiveness. In event-related potential (ERP) studies, the N170 component has been identified as face-selective. To determine the effect of color on face processing, we investigated the modulation of N170 by facial color. We recorded ERPs while subjects viewed facial color stimuli at 8 hue angles, which were generated by rotating the original facial color distribution around the white point by 45° for each human face. Responses to facial color were localized to the left, but not to the right hemisphere. N170 amplitudes gradually increased in proportion to the increase in hue angle from the natural-colored face. This suggests that N170 amplitude in the left hemisphere reflects processing of facial color information. Copyright © 2012 Elsevier Ltd. All rights reserved.

Face-space architectures: evidence for the use of independent color-based features.

PubMed

Nestor, Adrian; Plaut, David C; Behrmann, Marlene

2013-07-01

The concept of psychological face space lies at the core of many theories of face recognition and representation. To date, much of the understanding of face space has been based on principal component analysis (PCA); the structure of the psychological space is thought to reflect some important aspects of a physical face space characterized by PCA applications to face images. In the present experiments, we investigated alternative accounts of face space and found that independent component analysis provided the best fit to human judgments of face similarity and identification. Thus, our results challenge an influential approach to the study of human face space and provide evidence for the role of statistically independent features in face encoding. In addition, our findings support the use of color information in the representation of facial identity, and we thus argue for the inclusion of such information in theoretical and computational constructs of face space.

Early stages of figure-ground segregation during perception of the face-vase.

PubMed

Pitts, Michael A; Martínez, Antígona; Brewer, James B; Hillyard, Steven A

2011-04-01

The temporal sequence of neural processes supporting figure-ground perception was investigated by recording ERPs associated with subjects' perceptions of the face-vase figure. In Experiment 1, subjects continuously reported whether they perceived the face or the vase as the foreground figure by pressing one of two buttons. Each button press triggered a probe flash to the face region, the vase region, or the borders between the two. The N170/vertex positive potential (VPP) component of the ERP elicited by probes to the face region was larger when subjects perceived the faces as figure. Preceding the N170/VPP, two additional components were identified. First, when the borders were probed, ERPs differed in amplitude as early as 110 msec after probe onset depending on subjects' figure-ground perceptions. Second, when the face or vase regions were probed, ERPs were more positive (at ∼ 150-200 msec) when that region was perceived as figure versus background. These components likely reflect an early "border ownership" stage, and a subsequent "figure-ground segregation" stage of processing. To explore the influence of attention on these stages of processing, two additional experiments were conducted. In Experiment 2, subjects selectively attended to the face or vase region, and the same early ERP components were again produced. In Experiment 3, subjects performed an identical selective attention task, but on a display lacking distinctive figure-ground borders, and neither of the early components were produced. Results from these experiments suggest sequential stages of processing underlying figure-ground perception, each which are subject to modifications by selective attention.

An Own-Race Advantage for Components as Well as Configurations in Face Recognition

ERIC Educational Resources Information Center

Hayward, William G.; Rhodes, Gillian; Schwaninger, Adrian

2008-01-01

The own-race advantage in face recognition has been hypothesized as being due to a superiority in the processing of configural information for own-race faces. Here we examined the contributions of both configural and component processing to the own-race advantage. We recruited 48 Caucasian participants in Australia and 48 Chinese participants in…

A novel BCI based on ERP components sensitive to configural processing of human faces

NASA Astrophysics Data System (ADS)

Zhang, Yu; Zhao, Qibin; Jing, Jin; Wang, Xingyu; Cichocki, Andrzej

2012-04-01

This study introduces a novel brain-computer interface (BCI) based on an oddball paradigm using stimuli of facial images with loss of configural face information (e.g., inversion of face). To the best of our knowledge, till now the configural processing of human faces has not been applied to BCI but widely studied in cognitive neuroscience research. Our experiments confirm that the face-sensitive event-related potential (ERP) components N170 and vertex positive potential (VPP) have reflected early structural encoding of faces and can be modulated by the configural processing of faces. With the proposed novel paradigm, we investigate the effects of ERP components N170, VPP and P300 on target detection for BCI. An eight-class BCI platform is developed to analyze ERPs and evaluate the target detection performance using linear discriminant analysis without complicated feature extraction processing. The online classification accuracy of 88.7% and information transfer rate of 38.7 bits min-1 using stimuli of inverted faces with only single trial suggest that the proposed paradigm based on the configural processing of faces is very promising for visual stimuli-driven BCI applications.

A novel BCI based on ERP components sensitive to configural processing of human faces.

PubMed

Zhang, Yu; Zhao, Qibin; Jin, Jing; Wang, Xingyu; Cichocki, Andrzej

2012-04-01

This study introduces a novel brain-computer interface (BCI) based on an oddball paradigm using stimuli of facial images with loss of configural face information (e.g., inversion of face). To the best of our knowledge, till now the configural processing of human faces has not been applied to BCI but widely studied in cognitive neuroscience research. Our experiments confirm that the face-sensitive event-related potential (ERP) components N170 and vertex positive potential (VPP) have reflected early structural encoding of faces and can be modulated by the configural processing of faces. With the proposed novel paradigm, we investigate the effects of ERP components N170, VPP and P300 on target detection for BCI. An eight-class BCI platform is developed to analyze ERPs and evaluate the target detection performance using linear discriminant analysis without complicated feature extraction processing. The online classification accuracy of 88.7% and information transfer rate of 38.7 bits min(-1) using stimuli of inverted faces with only single trial suggest that the proposed paradigm based on the configural processing of faces is very promising for visual stimuli-driven BCI applications.

Face learning and the emergence of view-independent face recognition: an event-related brain potential study.

PubMed

Zimmermann, Friederike G S; Eimer, Martin

2013-06-01

Recognizing unfamiliar faces is more difficult than familiar face recognition, and this has been attributed to qualitative differences in the processing of familiar and unfamiliar faces. Familiar faces are assumed to be represented by view-independent codes, whereas unfamiliar face recognition depends mainly on view-dependent low-level pictorial representations. We employed an electrophysiological marker of visual face recognition processes in order to track the emergence of view-independence during the learning of previously unfamiliar faces. Two face images showing either the same or two different individuals in the same or two different views were presented in rapid succession, and participants had to perform an identity-matching task. On trials where both faces showed the same view, repeating the face of the same individual triggered an N250r component at occipito-temporal electrodes, reflecting the rapid activation of visual face memory. A reliable N250r component was also observed on view-change trials. Crucially, this view-independence emerged as a result of face learning. In the first half of the experiment, N250r components were present only on view-repetition trials but were absent on view-change trials, demonstrating that matching unfamiliar faces was initially based on strictly view-dependent codes. In the second half, the N250r was triggered not only on view-repetition trials but also on view-change trials, indicating that face recognition had now become more view-independent. This transition may be due to the acquisition of abstract structural codes of individual faces during face learning, but could also reflect the formation of associative links between sets of view-specific pictorial representations of individual faces. Copyright © 2013 Elsevier Ltd. All rights reserved.

Following the time course of face gender and expression processing: a task-dependent ERP study.

PubMed

Valdés-Conroy, Berenice; Aguado, Luis; Fernández-Cahill, María; Romero-Ferreiro, Verónica; Diéguez-Risco, Teresa

2014-05-01

The effects of task demands and the interaction between gender and expression in face perception were studied using event-related potentials (ERPs). Participants performed three different tasks with male and female faces that were emotionally inexpressive or that showed happy or angry expressions. In two of the tasks (gender and expression categorization) facial properties were task-relevant while in a third task (symbol discrimination) facial information was irrelevant. Effects of expression were observed on the visual P100 component under all task conditions, suggesting the operation of an automatic process that is not influenced by task demands. The earliest interaction between expression and gender was observed later in the face-sensitive N170 component. This component showed differential modulations by specific combinations of gender and expression (e.g., angry male vs. angry female faces). Main effects of expression and task were observed in a later occipito-temporal component peaking around 230 ms post-stimulus onset (EPN or early posterior negativity). Less positive amplitudes in the presence of angry faces and during performance of the gender and expression tasks were observed. Finally, task demands also modulated a positive component peaking around 400 ms (LPC, or late positive complex) that showed enhanced amplitude for the gender task. The pattern of results obtained here adds new evidence about the sequence of operations involved in face processing and the interaction of facial properties (gender and expression) in response to different task demands. Copyright © 2014 Elsevier B.V. All rights reserved.

The Challenges of Plasma Material Interactions in Nuclear Fusion Devices and Potential Solutions

DOE PAGES

Rapp, J.

2017-07-12

Plasma Material Interactions in future fusion reactors have been identified as a knowledge gap to be dealt with before any next step device past ITER can be built. The challenges are manifold. They are related to power dissipation so that the heat fluxes to the plasma facing components can be kept at technologically feasible levels; maximization of the lifetime of divertor plasma facing components that allow for steady-state operation in a reactor to reach the neutron fluences required; the tritium inventory (storage) in the plasma facing components, which can lead to potential safety concerns and reduction in the fuel efficiency;more » and it is related to the technology of the plasma facing components itself, which should demonstrate structural integrity under the high temperatures and neutron fluence. This contribution will give an overview and summary of those challenges together with some discussion of potential solutions. New linear plasma devices are needed to investigate the PMI under fusion reactor conditions and test novel plasma facing components. The Material Plasma Exposure eXperiment MPEX will be introduced and a status of the current R&D towards MPEX will be summarized.« less

The Challenges of Plasma Material Interactions in Nuclear Fusion Devices and Potential Solutions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rapp, J.

Plasma Material Interactions in future fusion reactors have been identified as a knowledge gap to be dealt with before any next step device past ITER can be built. The challenges are manifold. They are related to power dissipation so that the heat fluxes to the plasma facing components can be kept at technologically feasible levels; maximization of the lifetime of divertor plasma facing components that allow for steady-state operation in a reactor to reach the neutron fluences required; the tritium inventory (storage) in the plasma facing components, which can lead to potential safety concerns and reduction in the fuel efficiency;more » and it is related to the technology of the plasma facing components itself, which should demonstrate structural integrity under the high temperatures and neutron fluence. This contribution will give an overview and summary of those challenges together with some discussion of potential solutions. New linear plasma devices are needed to investigate the PMI under fusion reactor conditions and test novel plasma facing components. The Material Plasma Exposure eXperiment MPEX will be introduced and a status of the current R&D towards MPEX will be summarized.« less

Laser heterodyne surface profiler

DOEpatents

Sommargren, Gary E.

1982-01-01

A method and apparatus is disclosed for testing the deviation of the face of an object from a flat smooth surface using a beam of coherent light of two plane-polarized components, one of a frequency constantly greater than the other by a fixed amount to produce a difference frequency with a constant phase to be used as a reference. The beam also is split into its two components with the separate components directed onto spaced apart points onthe face of the object to be tested for smoothness. The object is rotated on an axis coincident with one component which is directed to the face of the object at the center which constitutes a virtual fixed point. This component also is used as a reference. The other component follows a circular track on the face of the object as the object is rotated. The two components are recombined after reflection to produce a reflected frequency difference of a phase proportional to the difference in path length which is compared with the reference phase to produce a signal proportional to the deviation of the height of the surface along the circular track with respect to the fixed point at the center.

Reconstructing Perceived and Retrieved Faces from Activity Patterns in Lateral Parietal Cortex.

PubMed

Lee, Hongmi; Kuhl, Brice A

2016-06-01

Recent findings suggest that the contents of memory encoding and retrieval can be decoded from the angular gyrus (ANG), a subregion of posterior lateral parietal cortex. However, typical decoding approaches provide little insight into the nature of ANG content representations. Here, we tested whether complex, multidimensional stimuli (faces) could be reconstructed from ANG by predicting underlying face components from fMRI activity patterns in humans. Using an approach inspired by computer vision methods for face recognition, we applied principal component analysis to a large set of face images to generate eigenfaces. We then modeled relationships between eigenface values and patterns of fMRI activity. Activity patterns evoked by individual faces were then used to generate predicted eigenface values, which could be transformed into reconstructions of individual faces. We show that visually perceived faces were reliably reconstructed from activity patterns in occipitotemporal cortex and several lateral parietal subregions, including ANG. Subjective assessment of reconstructed faces revealed specific sources of information (e.g., affect and skin color) that were successfully reconstructed in ANG. Strikingly, we also found that a model trained on ANG activity patterns during face perception was able to successfully reconstruct an independent set of face images that were held in memory. Together, these findings provide compelling evidence that ANG forms complex, stimulus-specific representations that are reflected in activity patterns evoked during perception and remembering. Neuroimaging studies have consistently implicated lateral parietal cortex in episodic remembering, but the functional contributions of lateral parietal cortex to memory remain a topic of debate. Here, we used an innovative form of fMRI pattern analysis to test whether lateral parietal cortex actively represents the contents of memory. Using a large set of human face images, we first extracted latent face components (eigenfaces). We then used machine learning algorithms to predict face components from fMRI activity patterns and, ultimately, to reconstruct images of individual faces. We show that activity patterns in a subregion of lateral parietal cortex, the angular gyrus, supported successful reconstruction of perceived and remembered faces, confirming a role for this region in actively representing remembered content. Copyright © 2016 the authors 0270-6474/16/366069-14$15.00/0.

Structural encoding processes contribute to individual differences in face and object cognition: Inferences from psychometric test performance and event-related brain potentials.

PubMed

Nowparast Rostami, Hadiseh; Sommer, Werner; Zhou, Changsong; Wilhelm, Oliver; Hildebrandt, Andrea

2017-10-01

The enhanced N1 component in event-related potentials (ERP) to face stimuli, termed N170, is considered to indicate the structural encoding of faces. Previously, individual differences in the latency of the N170 have been related to face and object cognition abilities. By orthogonally manipulating content domain (faces vs objects) and task demands (easy/speed vs difficult/accuracy) in both psychometric and EEG tasks, we investigated the uniqueness of the processes underlying face cognition as compared with object cognition and the extent to which the N1/N170 component can explain individual differences in face and object cognition abilities. Data were recorded from N = 198 healthy young adults. Structural equation modeling (SEM) confirmed that the accuracies of face perception (FP) and memory are specific abilities above general object cognition; in contrast, the speed of face processing was not differentiable from the speed of object cognition. Although there was considerable domain-general variance in the N170 shared with the N1, there was significant face-specific variance in the N170. The brain-behavior relationship showed that faster face-specific processes for structural encoding of faces are associated with higher accuracy in both perceiving and memorizing faces. Moreover, in difficult task conditions, qualitatively different processes are additionally needed for recognizing face and object stimuli as compared with easy tasks. The difficulty-dependent variance components in the N170 amplitude were related with both face and object memory (OM) performance. We discuss implications for understanding individual differences in face cognition. Copyright © 2017 Elsevier Ltd. All rights reserved.

Face recognition via edge-based Gabor feature representation for plastic surgery-altered images

NASA Astrophysics Data System (ADS)

Chude-Olisah, Chollette C.; Sulong, Ghazali; Chude-Okonkwo, Uche A. K.; Hashim, Siti Z. M.

2014-12-01

Plastic surgery procedures on the face introduce skin texture variations between images of the same person (intra-subject), thereby making the task of face recognition more difficult than in normal scenario. Usually, in contemporary face recognition systems, the original gray-level face image is used as input to the Gabor descriptor, which translates to encoding some texture properties of the face image. The texture-encoding process significantly degrades the performance of such systems in the case of plastic surgery due to the presence of surgically induced intra-subject variations. Based on the proposition that the shape of significant facial components such as eyes, nose, eyebrow, and mouth remains unchanged after plastic surgery, this paper employs an edge-based Gabor feature representation approach for the recognition of surgically altered face images. We use the edge information, which is dependent on the shapes of the significant facial components, to address the plastic surgery-induced texture variation problems. To ensure that the significant facial components represent useful edge information with little or no false edges, a simple illumination normalization technique is proposed for preprocessing. Gabor wavelet is applied to the edge image to accentuate on the uniqueness of the significant facial components for discriminating among different subjects. The performance of the proposed method is evaluated on the Georgia Tech (GT) and the Labeled Faces in the Wild (LFW) databases with illumination and expression problems, and the plastic surgery database with texture changes. Results show that the proposed edge-based Gabor feature representation approach is robust against plastic surgery-induced face variations amidst expression and illumination problems and outperforms the existing plastic surgery face recognition methods reported in the literature.

Brain-Behavior Correlations: Relationships between Mother-Stranger Face Processing and Infants' Behavioral Responses to a Separation from Mother

ERIC Educational Resources Information Center

Swingler, Margaret M.; Sweet, Monica A.; Carver, Leslie J.

2010-01-01

Event-related potentials (ERPs) were recorded from 6-month-olds (N = 30) as they looked at pictures of their mother's face and a stranger's face. Negative component (Nc) and P400 component responses from the ERP portion of the study were correlated with behavioral responses of the infants during a separation from their mothers. We measured the…

Event-related potentials of self-face recognition in children with pervasive developmental disorders.

PubMed

Gunji, Atsuko; Inagaki, Masumi; Inoue, Yuki; Takeshima, Yasuyuki; Kaga, Makiko

2009-02-01

Patients with pervasive developmental disorders (PDD) often have difficulty reading facial expressions and deciphering their implied meaning. We focused on semantic encoding related to face cognition to investigate event-related potentials (ERPs) to the subject's own face and familiar faces in children with and without PDD. Eight children with PDD (seven boys and one girl; aged 10.8+/-2.9 years; one left-handed) and nine age-matched typically developing children (four boys and five girls; aged 11.3+/-2.3 years; one left-handed) participated in this study. The stimuli consisted of three face images (self, familiar, and unfamiliar faces), one scrambled face image, and one object image (e.g., cup) with gray scale. We confirmed three major components: N170 and early posterior negativity (EPN) in the occipito-temporal regions (T5 and T6) and P300 in the parietal region (Pz). An enhanced N170 was observed as a face-specific response in all subjects. However, semantic encoding of each face might be unrelated to N170 because the amplitude and latency were not significantly different among the face conditions. On the other hand, an additional component after N170, EPN which was calculated in each subtracted waveform (self vs. familiar and familiar vs. unfamiliar), indicated self-awareness and familiarity with respect to face cognition in the control adults and children. Furthermore, the P300 amplitude in the control adults was significantly greater in the self-face condition than in the familiar-face condition. However, no significant differences in the EPN and P300 components were observed among the self-, familiar-, and unfamiliar-face conditions in the PDD children. The results suggest a deficit of semantic encoding of faces in children with PDD, which may be implicated in their delay in social communication.

Domain specificity versus expertise: factors influencing distinct processing of faces.

PubMed

Carmel, David; Bentin, Shlomo

2002-02-01

To explore face specificity in visual processing, we compared the role of task-associated strategies and expertise on the N170 event-related potential (ERP) component elicited by human faces with the ERPs elicited by cars, birds, items of furniture, and ape faces. In Experiment 1, participants performed a car monitoring task and an animacy decision task. In Experiment 2, participants monitored human faces while faces of apes were the distracters. Faces elicited an equally conspicuous N170, significantly larger than the ERPs elicited by non-face categories regardless of whether they were ignored or had an equal status with other categories (Experiment 1), or were the targets (in Experiment 2). In contrast, the negative component elicited by cars during the same time range was larger if they were targets than if they were not. Furthermore, unlike the posterior-temporal distribution of the N170, the negative component elicited by cars and its modulation by task were more conspicuous at occipital sites. Faces of apes elicited an N170 that was similar in amplitude to that elicited by the human face targets, albeit peaking 10 ms later. As our participants were not ape experts, this pattern indicates that the N170 is face-specific, but not specie-specific, i.e. it is elicited by particular face features regardless of expertise. Overall, these results demonstrate the domain specificity of the visual mechanism implicated in processing faces, a mechanism which is not influenced by either task or expertise. The processing of other objects is probably accomplished by a more general visual processor, which is sensitive to strategic manipulations and attention.

Comparative analysis of core heat transport of JET high density H-mode plasmas in carbon wall and ITER-like wall

NASA Astrophysics Data System (ADS)

Kim, Hyun-Tae; Romanelli, M.; Voitsekhovitch, I.; Koskela, T.; Conboy, J.; Giroud, C.; Maddison, G.; Joffrin, E.; contributors, JET

2015-06-01

A consistent deterioration of global confinement in H-mode experiments has been observed in JET [1] following the replacement of all carbon plasma facing components (PFCs) with an all metal (‘ITER-like’) wall (ILW). This has been correlated to the observed degradation of the pedestal confinement, as lower electron temperature (Te) values are routinely measured at the top of the edge barrier region. A comparative investigation of core heat transport in JET-ILW and JET-CW (carbon wall) discharges has been performed, to assess whether core confinement has also been affected by the wall change. The results presented here have been obtained by analysing a set of discharges consisting of high density JET-ILW H-mode plasmas and comparing them against their counterpart discharges in JET-CW having similar global operational parameters. The set contains 10 baseline ({βN}=1.5∼ 2 ) discharge-pairs with 2.7 T toroidal magnetic field, 2.5 MA plasma current, and 14 to 17 MW of neutral beam injection (NBI) heating. Based on a Te profile analysis using high resolution Thomson scattering (HRTS) data, the Te profile peaking (i.e. core Te (ρ = 0.3) / edge Te (ρ = 0.7)) is found to be similar, and weakly dependent on edge Te, for both JET-ILW and JET-CW discharges. When ILW discharges are seeded with N2, core and edge Te both increase to maintain a similar peaking factor. The change in core confinement is addressed with interpretative TRANSP simulations. It is found that JET-ILW H-mode plasmas have higher NBI power deposition to electrons and lower NBI power deposition to ions as compared to the JET-CW counterparts. This is an effect of the lower electron temperature at the top of the pedestal. As a result, the core electron energy confinement time is reduced in JET-ILW discharges, but the core ion energy confinement time is not decreased. Overall, the core energy confinement is found to be the same in the JET-ILW discharges compared to the JET-CW counterparts.

Laboratory Evaluation of Drop-in Solvent Alternatives to n-Propyl Bromide for Vapor Degreasing

NASA Technical Reports Server (NTRS)

Mitchell, Mark A.; Lowrey, Nikki M.

2012-01-01

Based on this limited laboratory study, solvent blends of trans-1,2 dichloroethylene with HFEs, HFCs, or PFCs appear to be viable alternatives to n-propyl bromide for vapor degreasing. The lower boiling points of these blends may lead to greater solvent loss during use. Additional factors must be considered when selecting a solvent substitute, including stability over time, VOC, GWP, toxicity, and business considerations.

Serum concentrations of perfluorinated compounds (PFC) ...

EPA Pesticide Factsheets

Perfluorinated compounds (PFCs) have been widely used in industrial applications and consumer products. Their persistent nature and potential health impacts are of concern. Given the high cost of collecting serum samples, this study is to understand whether we can quantify PFC serum concentrations using factors extracted from questionnaire responses and indirect measurements, and whether a single serum measurement can be used to classify an individual′s exposure over a one-year period. The study population included three demographic groups: young children (2–8 years old) (N=67), parents of young children (55 years old) (N=59). PFC serum concentrations, house dust concentrations, and questionnaires were collected. The geometric mean of perfluorooctane sulfonic acid (PFOS) was highest for the older adults. In contrast, the geometric mean of perfluorooctanoic acid (PFOA) was highest for children. Serum concentrations of the parent and the child from the same family were moderately correlated (Spearman correlation (r)=0.26–0.79, p<0.05), indicating common sources within a family. For adults, age, having occupational exposure or having used fire extinguisher, frequencies of consuming butter/margarine, pork, canned meat entrées, tuna and white fish, freshwater fish, and whether they ate microwave popcorn were significantly positively associated with serum concentrations of individual PFCs. For children, residential dust

Honeywell optical investigations on FLASH program

NASA Astrophysics Data System (ADS)

O'Rourke, Ken; Peterson, Eric; Yount, Larry

1995-05-01

The increasing performance and reduction of life cycle cost requirements placed on commercial and military transport aircraft are resulting in more complex, highly integrated aircraft control and management systems. The use of fiber optic data transmission media can make significant contributions in achieving these performance and cost goals. The Honeywell portion of Task 2A on the Fly-by-Light Advanced System Hardware (FLASH) program is evaluating a Primary Flight Control System (PFCS) using pilot and copilot inputs from Active Hand Controllers (AHC) which are optically linked to the primary flight Control Computers (PFCC). Customer involvement is an important element of the Task 2A activity. Establishing customer requirements and perspectives on productization of systems developed under FLASH are key to future product success. The Honeywell elements of the PFCS demonstrator provide a command path that is optically interfaced from crew inputs to commands of distributed, smart actuation subsystems commands. Optical communication architectures are implemented using several protocols including the new AS-1773A 20 Mbps data bus standard. The interconnecting fiber optic cable plant is provided by our Task 1A teammate McDonnell Douglas Aerospace (West). Fiber optic cable plant fabrication uses processed, tools and materials reflecting necessary advances in manufacturing required to make fly-by-light avionics systems marketable.

Chlorinated, brominated and fluorinated organic pollutants in African Penguin eggs: 30 years since the previous assessment.

PubMed

Bouwman, Hindrik; Govender, Danny; Underhill, Les; Polder, Anuschka

2015-05-01

The African Penguin population has drastically declined over the last 100 years. Changes in food availability due to over-fishing and other oceanographic changes seem to be major causes. However, it has also been 30 years since organic pollutants as a potential factor have been assessed. We analysed penguin eggs collected in 2011 and 2012 from two breeding colonies 640 km apart: Robben Island near Cape Town on the Atlantic Ocean coast, and Bird Island near Port Elizabeth on the Indian Ocean coast of South Africa. We quantified organochlorine pesticides, brominated flame retardants, and perfluorinated compounds (PFCs). Compared to 30 years ago, concentrations of ΣDDT have remained about the same or slightly lower, while ΣPCBs declined almost four-fold. The use of DDT in malaria control is unlikely to have contributed. PFCs were detected in all eggs. Indications (non-significant) of eggshell thinning associated with ΣDDT and ΣPCB was found. It seems therefore that the concentrations of measured organic pollutants the African Penguin eggs are not contributing directly to its current demise, but concerns remain about thinner shells and desiccation. Effects of combinations of compounds and newer compounds cannot be excluded, as well as more subtle effects on reproduction, development, and behaviour. Copyright © 2014 Elsevier Ltd. All rights reserved.

Characterization of the thermolysis products of Nafion membrane: A potential source of perfluorinated compounds in the environment

NASA Astrophysics Data System (ADS)

Feng, Mingbao; Qu, Ruijuan; Wei, Zhongbo; Wang, Liansheng; Sun, Ping; Wang, Zunyao

2015-05-01

The thermal decomposition of Nafion N117 membrane, a typical perfluorosulfonic acid membrane that is widely used in various chemical technologies, was investigated in this study. Structural identification of thermolysis products in water and methanol was performed using liquid chromatography-electrospray ionization-tandem mass spectrometry (LC/ESI-MS/MS). The fluoride release was studied using an ion-chromatography system, and the membrane thermal stability was characterized by thermogravimetric analysis. Notably, several types of perfluorinated compounds (PFCs) including perfluorocarboxylic acids were detected and identified. Based on these data, a thermolysis mechanism was proposed involving cleavage of both the polymer backbone and its side chains by attack of radical species. This is the first systematic report on the thermolysis products of Nafion by simulating its high-temperature operation and disposal process via incineration. The results of this study indicate that Nafion is a potential environmental source of PFCs, which have attracted growing interest and concern in recent years. Additionally, this study provides an analytical justification of the LC/ESI-MS/MS method for characterizing the degradation products of polymer electrolyte membranes. These identifications can substantially facilitate an understanding of their decomposition mechanisms and offer insight into the proper utilization and effective management on these membranes.

Molecular dynamics simulations of structural transformation of perfluorooctane sulfonate (PFOS) at water/rutile interfaces.

PubMed

He, Guangzhi; Zhang, Meiyi; Zhou, Qin; Pan, Gang

2015-09-01

Concentration and salinity conditions are the dominant environmental factors affecting the behavior of perfluorinated compounds (PFCs) on the surfaces of a variety of solid matrices (suspended particles, sediments, and natural minerals). However, the mechanism has not yet been examined at molecular scales. Here, the structural transformation of perfluorooctane sulfonate (PFOS) at water/rutile interfaces induced by changes of the concentration level of PFOS and salt condition was investigated using molecular dynamics (MD) simulations. At low and intermediate concentrations all PFOS molecules directly interacted with the rutile (110) surface mainly by the sulfonate headgroups through electrostatic attraction, yielding a typical monolayer structure. As the concentration of PFOS increased, the molecules aggregated in a complex multi-layered structure, where an irregular assembling configuration was adsorbed on the monolayer structure by the van der Waals interactions between the perfluoroalkyl chains. When adding CaCl2 to the system, the multi-layered structure changed to a monolayer again, indicating that the addition of CaCl2 enhanced the critical concentration value to yield PFOS multilayer assemblies. The divalent Ca(2+) substituted for monovalent K(+) as the bridging counterion in PFOS adsorption. MD simulation may trigger wide applications in study of perfluorinated compounds (PFCs) from atomic/molecular scale. Copyright © 2015 Elsevier Ltd. All rights reserved.

Preliminary assessment on the bioaccessibility of contaminants of emerging concern in raw and cooked seafood.

PubMed

Alves, Ricardo N; Maulvault, Ana L; Barbosa, Vera L; Cunha, Sara; Kwadijk, Christiaan J A F; Álvarez-Muñoz, Diana; Rodríguez-Mozaz, Sara; Aznar-Alemany, Òscar; Eljarrat, Ethel; Barceló, Damià; Fernandez-Tejedor, Margarita; Tediosi, Alice; Marques, António

2017-06-01

A preliminary assessment of the bioaccessibility of contaminants of emerging concern (CeCs), including perfluorinated compounds (PFCs; i.e. PFOS and PFUnA), brominated flame retardants (BFRs; i.e. BDE47, BDE100, α-HBCD) and pharmaceuticals and personal care products (PPCPs; i.e. venlafaxine, methylparaben and UV-filter OC) was performed in seafood species available in the European markets. Additionally, the effect of steaming on CeCs bioaccessibility was also investigated for the first time. Overall, steaming affected differentially contaminants' concentrations, for instance, decreasing PFOS levels in flounder, but increasing both BDE47 and BDE100. CeCs bioaccessibility varied according to seafood species and contaminant group, i.e. in general, lower bioaccessibility values were obtained for PBDEs (<70%, except for mackerel), while PFCs and PPCPs revealed higher bioaccessibility percentages (between 71 and 95%). The lowest bioaccessibility value was obtained for α-HBCD (mussel; 14%), whereas the highest percentage was observed in venlafaxine (mullet; 95%). Our preliminary study reports also, for the first time, the effects of steaming on CeCs bioaccessibility. In most cases, bioaccessibility was not affected by cooking, however, a decrease was observed in PBDEs and venlafaxine bioaccessibility in steamed mussels and mullet, respectively, thus lowering the potential health risks associated with seafood consumption. Copyright © 2017 Elsevier Ltd. All rights reserved.

Review: Micro-organic contaminants in groundwater in China

NASA Astrophysics Data System (ADS)

Dong, Weihong; Xie, Wei; Su, Xiaosi; Wen, Chuanlei; Cao, Zhipeng; Wan, Yuyu

2018-03-01

Micro-organic contaminants (MOs) in groundwater, which may have adverse effects on human health and ecosystems worldwide, are gaining increased attention in China. A great deal of research has been conducted to investigate their sources, occurrences and behavior in aquifers. This paper reviews the main sources, distribution, concentrations and behavior of a wide range of MOs in groundwater in China. These MOs include well-established persistent organic pollutants—polycyclic aromatic hydrocarbons (PAHs), hexachlorocyclohexanes (HCHs), polychlorinated biphenyls (PCBs), endocrine disrupting chemicals (poly brominated diphenyl ethers (PBDEs), phthalic acid esters (PAEs), bisphenol A (BPA)—and some contaminants of emerging concern such as pharmaceutical and personal care products (antibiotics, caffeine, shampoos) and perfluorinated compounds (PFCs). The results reveal that the main MOs in groundwater are PAHs, organochlorine pesticides (OCPs), PBDEs, PAEs, and antibiotics. Moreover, some PFCs such as perfluorobutane sulfonic acid (PFBS), perfluorobutanoic acid (PFBA) and perfluorooctanoic acid (PFOA) have only recently been observed in groundwater as emerging organic contaminants. Additionally, most MOs are distributed in populated and industrialized areas such as the southeast coast of China. Finally, industrial emissions, wastewater treatment plant effluents and agricultural wastewater are found to be dominant sources of MOs in groundwater. Based on the existing pollution levels, regulation and amelioration of MOs are warranted.

Complementary methods for the determination of dissolved oxygen content in perfluorocarbon emulsions and other solutions.

PubMed

Fraker, Christopher A; Mendez, Armando J; Stabler, Cherie L

2011-09-08

Perfluorocarbons (PFCs) are compounds with increased oxygen solubility and effective diffusivity, making them ideal candidates for improving oxygen mass transfer in numerous biological applications. Historically, quantification of the mass transfer characteristics of these liquids has relied on the use of elaborate laboratory equipment and complicated methodologies, such as in-line gas chromatography coupled with temperature-controlled glass fritted diffusion cells. In this work, we present an alternative method for the determination of dissolved oxygen content in PFC emulsions and, by extrapolation, pure PFCs. We implemented a simple stirred oxygen consumption microchamber coupled with an enzymatic reaction for the quantitative determination of oxygen by optical density measurements. Chambers were also custom fitted with lifetime oxygen sensors to permit simultaneous measurement of internal chamber oxygen levels. Analyzing the consumption of oxygen during the enzymatic reaction via recorded oxygen depletion traces, we found a strong degree of correlation between the zero-order reaction rate and the total measured oxygen concentrations, relative to control solutions. The values obtained were in close agreement with published values in the literature, establishing the accuracy of this method. Overall, this method allows for easy, reliable, and reproducible measurements of oxygen content in aqueous solutions, including, but not limited to PFC emulsions.

Environmental Chemicals in an Urban Population of Pregnant Women and Their Newborns from San Francisco.

PubMed

Morello-Frosch, Rachel; Cushing, Lara J; Jesdale, Bill M; Schwartz, Jackie M; Guo, Weihong; Guo, Tan; Wang, Miaomiao; Harwani, Suhash; Petropoulou, Syrago-Styliani E; Duong, Wendy; Park, June-Soo; Petreas, Myrto; Gajek, Ryszard; Alvaran, Josephine; She, Jianwen; Dobraca, Dina; Das, Rupali; Woodruff, Tracey J

2016-11-15

Exposures to environmental pollutants in utero may increase the risk of adverse health effects. We measured the concentrations of 59 potentially harmful chemicals in 77 maternal and 65 paired umbilical cord blood samples collected in San Francisco during 2010-2011, including polychlorinated biphenyls (PCBs), organochlorine pesticides (OCPs), polybrominated diphenyl ethers (PBDEs), hydroxylated PBDEs (OH-PBDEs), and perfluorinated compounds (PFCs) in serum and metals in whole blood. Consistent with previous studies, we found evidence that concentrations of mercury (Hg) and lower-brominated PBDEs were often higher in umbilical cord blood or serum than in maternal samples (median cord:maternal ratio > 1), while for most PFCs and lead (Pb), concentrations in cord blood or serum were generally equal to or lower than their maternal pair (median cord:maternal ratio ≤ 1). In contrast to the conclusions of a recent review, we found evidence that several PCBs and OCPs were also often higher in cord than maternal serum (median cord:maternal ratio > 1) when concentrations are assessed on a lipid-adjusted basis. Our findings suggest that for many chemicals, fetuses may experience higher exposures than their mothers and highlight the need to characterize potential health risks and inform policies aimed at reducing sources of exposure.

Perfluoroalkyl chemicals in vacuum cleaner dust from 39 Wisconsin homes.

PubMed

Knobeloch, Lynda; Imm, Pamela; Anderson, Henry

2012-08-01

Perfluoroalkyl chemicals (PFCs) have been used as surfactants and stain repellants in a variety of consumer products for more than 50years and there is growing concern regarding their persistence and toxicity. Human exposure to these chemicals is essentially universal in North America and researchers have linked them to a variety of health problems ranging from higher rates of cancer, to developmental and reproductive problems, and higher cholesterol levels. Major exposure pathways are food and water ingestion, dust ingestion via hand to mouth transfer. In an effort to assess residential exposure, the Wisconsin Department of Health Services tested vacuum cleaner contents from thirty-nine homes for 16 perflouroalkyl chemicals. PFOS, PFOA, PFHxS, PFHpA and PFNA were found in all of the vacuum dust samples and dust from eight homes contained all 16 PFCs included in our analysis. The most commonly detected compounds were perfluorooctanesulfonate (PFOS), perfluorohexanesulfonate (PFHxS) and perfluorooctanoic acid (PFOA) which together made up 70% of the total PFC residues in dust from these homes. Summed PFC concentrations in these dust samples ranged from 70 to 2513ng/g (median 280ng/g). Our investigation suggests that these chemicals may be ubiquitous contaminants in US homes. Copyright © 2012 Elsevier Ltd. All rights reserved.

Polyfluorinated Compounds in Serum Linked to Indoor Air in Office Environments

PubMed Central

Fraser, Alicia J; Webster, Thomas F; Watkins, Deborah J; Nelson, Jessica W; Stapleton, Heather M; Calafat, Antonia M; Kato, Kayoko; Shoeib, Mahiba; Vieira, Verónica M; McClean, Michael D

2011-01-01

We aimed to investigate the role of indoor office air on exposure to polyfluorinated compounds (PFCs) among office workers. Week-long, active air sampling was conducted during the winter of 2009 in 31 offices in Boston, MA. Air samples were analyzed for fluorotelomer alcohols (FTOHs), sulfonamides (FOSAs), and sulfonamidoethanols (FOSEs). Serum was collected from each participant (n=31) and analyzed for twelve PFCs including PFOA and PFOS. In air, FTOHs were present in the highest concentrations, particularly 8:2-FTOH (GM=9,920 pg/m3). FTOHs varied significantly by building with the highest levels observed in a newly constructed building. PFOA in serum was significantly correlated with air levels of 6:2-FTOH (r=0.43), 8:2-FTOH (r=0.60), and 10:2-FTOH (r=0.62). Collectively, FTOHs in air significantly predicted PFOA in serum (p < 0.001) and explained approximately 36% of the variation in serum PFOA concentrations. PFOS in serum was not associated with air levels of FOSAs/FOSEs. In conclusion, FTOH concentrations in office air significantly predict serum PFOA concentrations in office workers. Variation in PFC air concentrations by building is likely due to differences in the number, type, and age of potential sources such as carpeting, furniture and/or paint. PMID:22148395

Polyfluorinated compounds in serum linked to indoor air in office environments.

PubMed

Fraser, Alicia J; Webster, Thomas F; Watkins, Deborah J; Nelson, Jessica W; Stapleton, Heather M; Calafat, Antonia M; Kato, Kayoko; Shoeib, Mahiba; Vieira, Verónica M; McClean, Michael D

2012-01-17

We aimed to investigate the role of indoor office air on exposure to polyfluorinated compounds (PFCs) among office workers. Week-long, active air sampling was conducted during the winter of 2009 in 31 offices in Boston, MA. Air samples were analyzed for fluorotelomer alcohols (FTOHs), sulfonamides (FOSAs), and sulfonamidoethanols (FOSEs). Serum was collected from each participant (n = 31) and analyzed for 12 PFCs including PFOA and PFOS. In air, FTOHs were present in the highest concentrations, particularly 8:2-FTOH (GM = 9920 pg/m(3)). FTOHs varied significantly by building with the highest levels observed in a newly constructed building. PFOA in serum was significantly correlated with air levels of 6:2-FTOH (r = 0.43), 8:2-FTOH (r = 0.60), and 10:2-FTOH (r = 0.62). Collectively, FTOHs in air significantly predicted PFOA in serum (p < 0.001) and explained approximately 36% of the variation in serum PFOA concentrations. PFOS in serum was not associated with air levels of FOSAs/FOSEs. In conclusion, FTOH concentrations in office air significantly predict serum PFOA concentrations in office workers. Variation in PFC air concentrations by building is likely due to differences in the number, type, and age of potential sources such as carpeting, furniture, and/or paint.

Analytical methods for the quantification of bisphenol A, alkylphenols, phthalate esters, and perfluoronated chemicals in biological samples.

PubMed

Nakazawa, Hiroyuki; Iwasaki, Yusuke; Ito, Rie

2014-01-01

Our modern society has created a large number of chemicals that are used for the production of everyday commodities including toys, food packaging, cosmetic products, and building materials. We enjoy a comfortable and convenient lifestyle with access to these items. In addition, in specialized areas, such as experimental science and various medical fields, laboratory equipment and devices that are manufactured using a wide range of chemical substances are also extensively employed. The association between human exposure to trace hazardous chemicals and an increased incidence of endocrine disease has been recognized. However, the evaluation of human exposure to such endocrine disrupting chemicals is therefore imperative, and the determination of exposure levels requires the analysis of human biological materials, such as blood and urine. To obtain as much information as possible from limited sample sizes, highly sensitive and reliable analytical methods are also required for exposure assessments. The present review focuses on effective analytical methods for the quantification of bisphenol A (BPA), alkylphenols (APs), phthalate esters (PEs), and perfluoronated chemicals (PFCs), which are chemicals used in the production of everyday commodities. Using data obtained from liquid chromatography/mass spectrometry (LC/MS) and LC/MS/MS analyses, assessments of the risks to humans were also presented based on the estimated levels of exposure to PFCs.

Structural face encoding: How task affects the N170's sensitivity to race.

PubMed

Senholzi, Keith B; Ito, Tiffany A

2013-12-01

The N170 event-related potential (ERP) component differentiates faces from non-faces, but studies aimed at investigating whether the processing indexed by this component is also sensitive to racial differences among faces have garnered conflicting results. Here, we explore how task affects the influence of race on the N170 among White participants. N170s were larger to ingroup White faces than outgroup Black faces, but only for those required to attend to race, suggesting that attention to race can result in deeper levels of processing for ingroup members. Conversely, N170s were larger to Black faces than White faces for participants who attended to the unique identity of the faces, suggesting that attention to identity can result in preferential recruitment of cognitive resources for outgroup members. Taken together, these findings suggest that race can differentially impact face processing at early stages of encoding, but differences in processing are contingent upon one's goal state.

Individual differences in perceiving and recognizing faces-One element of social cognition.

PubMed

Wilhelm, Oliver; Herzmann, Grit; Kunina, Olga; Danthiir, Vanessa; Schacht, Annekathrin; Sommer, Werner

2010-09-01

Recognizing faces swiftly and accurately is of paramount importance to humans as a social species. Individual differences in the ability to perform these tasks may therefore reflect important aspects of social or emotional intelligence. Although functional models of face cognition based on group and single case studies postulate multiple component processes, little is known about the ability structure underlying individual differences in face cognition. In 2 large individual differences experiments (N = 151 and N = 209), a broad variety of face-cognition tasks were tested and the component abilities of face cognition-face perception, face memory, and the speed of face cognition-were identified and then replicated. Experiment 2 also showed that the 3 face-cognition abilities are clearly distinct from immediate and delayed memory, mental speed, general cognitive ability, and object cognition. These results converge with functional and neuroanatomical models of face cognition by demonstrating the difference between face perception and face memory. The results also underline the importance of distinguishing between speed and accuracy of face cognition. Together our results provide a first step toward establishing face-processing abilities as an independent ability reflecting elements of social intelligence. (PsycINFO Database Record (c) 2010 APA, all rights reserved).

The N170 component is sensitive to face-like stimuli: a study of Chinese Peking opera makeup.

PubMed

Liu, Tiantian; Mu, Shoukuan; He, Huamin; Zhang, Lingcong; Fan, Cong; Ren, Jie; Zhang, Mingming; He, Weiqi; Luo, Wenbo

2016-12-01

The N170 component is considered a neural marker of face-sensitive processing. In the present study, the face-sensitive N170 component of event-related potentials (ERPs) was investigated with a modified oddball paradigm using a natural face (the standard stimulus), human- and animal-like makeup stimuli, scrambled control images that mixed human- and animal-like makeup pieces, and a grey control image. Nineteen participants were instructed to respond within 1000 ms by pressing the ' F ' or ' J ' key in response to the standard or deviant stimuli, respectively. We simultaneously recorded ERPs, response accuracy, and reaction times. The behavioral results showed that the main effect of stimulus type was significant for reaction time, whereas there were no significant differences in response accuracies among stimulus types. In relation to the ERPs, N170 amplitudes elicited by human-like makeup stimuli, animal-like makeup stimuli, scrambled control images, and a grey control image progressively decreased. A right hemisphere advantage was observed in the N170 amplitudes for human-like makeup stimuli, animal-like makeup stimuli, and scrambled control images but not for grey control image. These results indicate that the N170 component is sensitive to face-like stimuli and reflect configural processing in face recognition.

Recognition and identification of famous faces in patients with unilateral temporal lobe epilepsy.

PubMed

Seidenberg, Michael; Griffith, Randall; Sabsevitz, David; Moran, Maria; Haltiner, Alan; Bell, Brian; Swanson, Sara; Hammeke, Thomas; Hermann, Bruce

2002-01-01

We examined the performance of 21 patients with unilateral temporal lobe epilepsy (TLE) and hippocampal damage (10 lefts, and 11 rights) and 10 age-matched controls on the recognition and identification (name and occupation) of well-known faces. Famous face stimuli were selected from four time periods; 1970s, 1980s, 1990-1994, and 1995-1996. Differential patterns of performance were observed for the left and right TLE group across distinct face processing components. The left TLE group showed a selective impairment in naming famous faces while they performed similar to the controls in face recognition and semantic identification (i.e. occupation). In contrast, the right TLE group was impaired across all components of face memory; face recognition, semantic identification, and face naming. Face naming impairment in the left TLE group was characterized by a temporal gradient with better naming performance for famous faces from more distant time periods. Findings are discussed in terms of the role of the temporal lobe system for the acquisition, retention, and retrieval of face semantic networks, and the differential effects of lateralized temporal lobe lesions in this process.

Exploring the functional architecture of person recognition system with event-related potentials in a within- and cross-domain self-priming of faces.

PubMed

Jemel, Boutheina; Pisani, Michèle; Rousselle, Laurence; Crommelinck, Marc; Bruyer, Raymond

2005-01-01

In this paper, we explored the functional properties of person recognition system by investigating the onset, magnitude, and scalp distribution of within- and cross-domain self-priming effects on event-related potentials (ERPs). Recognition of degraded pictures of famous people was enhanced by a prior exposure to the same person's face (within-domain self-priming) or name (cross-domain self-priming) as compared to those preceded by neutral or unrelated primes. The ERP results showed first that the amplitude of the N170 component to famous face targets was modulated by within- and cross-domain self-priming, suggesting not only that the N170 component can be affected by top-down influences but also that this top-down effect crosses domains. Second, similar to our behavioral data, later ERPs to famous faces showed larger ERP self-priming effects in the within-domain than in the cross-domain condition. In addition, the present data dissociated between two topographically and temporally overlapping priming-sensitive ERP components: the first one, with a strongly posterior distribution arising at an early onset, was modulated more by within-domain priming irrespective whether the repeated face was familiar or not. The second component, with a relatively uniform scalp distribution, was modulated by within- and cross-domain priming of familiar faces. Moreover, there was no evidence for ERP-induced modulations for unfamiliar face targets in the cross-domain condition. Together, our findings suggest that multiple neurocognitive events that are possibly mediated by distinct brain loci contribute to face priming effects.

The time course of individual face recognition: A pattern analysis of ERP signals.

PubMed

Nemrodov, Dan; Niemeier, Matthias; Mok, Jenkin Ngo Yin; Nestor, Adrian

2016-05-15

An extensive body of work documents the time course of neural face processing in the human visual cortex. However, the majority of this work has focused on specific temporal landmarks, such as N170 and N250 components, derived through univariate analyses of EEG data. Here, we take on a broader evaluation of ERP signals related to individual face recognition as we attempt to move beyond the leading theoretical and methodological framework through the application of pattern analysis to ERP data. Specifically, we investigate the spatiotemporal profile of identity recognition across variation in emotional expression. To this end, we apply pattern classification to ERP signals both in time, for any single electrode, and in space, across multiple electrodes. Our results confirm the significance of traditional ERP components in face processing. At the same time though, they support the idea that the temporal profile of face recognition is incompletely described by such components. First, we show that signals associated with different facial identities can be discriminated from each other outside the scope of these components, as early as 70ms following stimulus presentation. Next, electrodes associated with traditional ERP components as well as, critically, those not associated with such components are shown to contribute information to stimulus discriminability. And last, the levels of ERP-based pattern discrimination are found to correlate with recognition accuracy across subjects confirming the relevance of these methods for bridging brain and behavior data. Altogether, the current results shed new light on the fine-grained time course of neural face processing and showcase the value of novel methods for pattern analysis to investigating fundamental aspects of visual recognition. Copyright © 2016 Elsevier Inc. All rights reserved.

Dissociations of subliminal and supraliminal self-face from other-face processing: behavioral and ERP evidence.

PubMed

Geng, Haiyan; Zhang, Shen; Li, Qi; Tao, Ran; Xu, Shan

2012-10-01

Self-related information has been found to be processed more quickly and accurately in studies with supraliminal self-stimuli and traditional paradigms such as masked priming. We conducted two experiments to investigate whether subliminal self-face processing enjoys this advantage and the neural correlates of processing self-faces at both subliminal and supraliminal levels. We found that self-faces were quicker than famous-other faces to gain dominance against dynamic noise patterns during prolonged interocular suppression to enter awareness (Experiment 1). Meanwhile, subliminal contrast of self- and famous-other face processing was reflected in a reduced early vertex positive potential (VPP) component, whereas supraliminal self-other face differentiation was reflected in an enhanced N170, as well as a more positive late component (300-580ms, Experiment 2) to the self-face. The clear dissociations of self- and other-face processing found across our two experiments validate the self advantage. Our findings also contribute to understandings of the mechanisms underlying self-face processing at different levels of awareness. Copyright © 2012 Elsevier Ltd. All rights reserved.

Methods and systems for determining angular orientation of a drill string

DOEpatents

Cobern, Martin E.

2010-03-23

Preferred methods and systems generate a control input based on a periodically-varying characteristic associated with the rotation of a drill string. The periodically varying characteristic can be correlated with the magnetic tool face and gravity tool face of a rotating component of the drill string, so that the control input can be used to initiate a response in the rotating component as a function of gravity tool face.

Holistic Processing of Faces: Perceptual and Decisional Components

ERIC Educational Resources Information Center

Richler, Jennifer J.; Gauthier, Isabel; Wenger, Michael J.; Palmeri, Thomas J.

2008-01-01

Researchers have used several composite face paradigms to assess holistic processing of faces. In the selective attention paradigm, participants decide whether one face part (e.g., top) is the same as a previously seen face part. Their judgment is affected by whether the irrelevant part of the test face is the same as or different than the…

Analysis of singular interface stresses in dissimilar material joints for plasma facing components

NASA Astrophysics Data System (ADS)

You, J. H.; Bolt, H.

2001-10-01

Duplex joint structures are typical material combinations for the actively cooled plasma facing components of fusion devices. The structural integrity under the incident heat loads from the plasma is one of the most crucial issues in the technology of these components. The most critical domain in a duplex joint component is the free surface edge of the bond interface between heterogeneous materials. This is due to the fact that the thermal stress usually shows a singular intensification in this region. If the plasma facing armour tile consists of a brittle material, the existence of the stress singularity can be a direct cause of failure. The present work introduces a comprehensive analytical tool to estimate the impact of the stress singularity for duplex PFC design and quantifies the relative stress intensification in various materials joints by use of a model formulated by Munz and Yang. Several candidate material combinations of plasma facing armour and metallic heat sink are analysed and the results are compared with each other.

Clinical Phase IIB Trial of Oxycyte Perflurocarbon in Severe Human Traumatic Brain Injury

DTIC Science & Technology

2013-10-01

TERMS Penetrating ballistic brain injury, ischemia, hypoxia, perfluorocarbon , cell death, perfusion. 16. SECURITY CLASSIFICATION OF: 17. LIMITATION...SUBTITLE The Role of Perfluorocarbons in Mitigating Traumatic Brain Injury 5a. CONTRACT NUMBER W81XWH-08-1-0419 5b. GRANT NUMBER 5c. PROGRAM...damage seems to be mediated by mechanisms that follow the initial injury (secondary mechanisms). Perfluorocarbons (PFCs) are one of the methods by which

Plasma facing materials and components for future fusion devices—development, characterization and performance under fusion specific loading conditions

NASA Astrophysics Data System (ADS)

Linke, J.

2006-04-01

The plasma exposed components in existing and future fusion devices are strongly affected by the plasma material interaction processes. These mechanisms have a strong influence on the plasma performance; in addition they have major impact on the lifetime of the plasma facing armour and the joining interface between the plasma facing material (PFM) and the heat sink. Besides physical and chemical sputtering processes, high heat quasi-stationary fluxes during normal and intense thermal transients are of serious concern for the engineers who develop reliable wall components. In addition, the material and component degradation due to intense fluxes of energetic neutrons is another critical issue in D-T-burning fusion devices which requires extensive R&D. This paper presents an overview on the materials development and joining, the testing of PFMs and components, and the analysis of the neutron irradiation induced degradation.

Evaluation of runaway-electron effects on plasma-facing components for NET

NASA Astrophysics Data System (ADS)

Bolt, H.; Calén, H.

1991-03-01

Runaway electrons which are generated during disruptions can cause serious damage to plasma facing components in a next generation device like NET. A study was performed to quantify the response of NET plasma facing components to runaway-electron impact. For the determination of the energy deposition in the component materials Monte Carlo computations were performed. Since the subsurface metal structures can be strongly heated under runaway-electron impact from the computed results damage threshold values for the thermal excursions were derived. These damage thresholds are strongly dependent on the materials selection and the component design. For a carbonmolybdenum divertor with 10 and 20 mm carbon armour thickness and 1 degree electron incidence the damage thresholds are 100 MJ/m 2 and 220 MJ/m 2. The thresholds for a carbon-copper divertor under the same conditions are about 50% lower. On the first wall damage is anticipated for energy depositions above 180 MJ/m 2.

Differential processing of part-to-whole and part-to-part face priming: an ERP study.

PubMed

Jemel, B; George, N; Chaby, L; Fiori, N; Renault, B

1999-04-06

We provide electrophysiological evidence supporting the hypothesis that part and whole face processing involve distinct functional mechanisms. We used a congruency judgment task and studied part-to-whole and part-to-part priming effects. Neither part-to-whole nor part-to-part conditions elicited early congruency effects on face-specific ERP components, suggesting that activation of the internal representations should occur later on. However, these components showed differential responsiveness to whole faces and isolated eyes. In addition, although late ERP components were affected when the eye targets were not associated with the prime in both conditions, their temporal and topographical features depended on the latter. These differential effects suggest the existence of distributed neural networks in the inferior temporal cortex where part and whole facial representations may be stored.

How components of facial width to height ratio differently contribute to the perception of social traits

PubMed Central

Lio, Guillaume; Gomez, Alice; Sirigu, Angela

2017-01-01

Facial width to height ratio (fWHR) is a morphological cue that correlates with sexual dimorphism and social traits. Currently, it is unclear how vertical and horizontal components of fWHR, distinctly capture faces’ social information. Using a new methodology, we orthogonally manipulated the upper facial height and the bizygomatic width to test their selective effect in the formation of impressions. Subjects (n = 90) saw pair of faces and had to select the face expressing better different social traits (trustworthiness, aggressiveness and femininity). We further investigated how sex and fWHR components interact in the formation of these judgements. Across experiments, changes along the vertical component better predicted participants' ratings rather than the horizontal component. Faces with smaller height were perceived as less trustworthy, less feminine and more aggressive. By dissociating fWHR and testing the contribution of its components independently, we obtained a powerful and discriminative measure of how facial morphology guides social judgements. PMID:28235081

Early Stages of Figure–Ground Segregation during Perception of the Face–Vase

PubMed Central

Pitts, Michael A.; Martínez, Antígona; Brewer, James B.; Hillyard, Steven A.

2011-01-01

The temporal sequence of neural processes supporting figure–ground perception was investigated by recording ERPs associated with subjects’ perceptions of the face–vase figure. In Experiment 1, subjects continuously reported whether they perceived the face or the vase as the foreground figure by pressing one of two buttons. Each button press triggered a probe flash to the face region, the vase region, or the borders between the two. The N170/vertex positive potential (VPP) component of the ERP elicited by probes to the face region was larger when subjects perceived the faces as figure. Preceding the N170/VPP, two additional components were identified. First, when the borders were probed, ERPs differed in amplitude as early as 110 msec after probe onset depending on subjects’ figure–ground perceptions. Second, when the face or vase regions were probed, ERPs were more positive (at ~150–200 msec) when that region was perceived as figure versus background. These components likely reflect an early “border ownership” stage, and a subsequent “figure–ground segregation” stage of processing. To explore the influence of attention on these stages of processing, two additional experiments were conducted. In Experiment 2, subjects selectively attended to the face or vase region, and the same early ERP components were again produced. In Experiment 3, subjects performed an identical selective attention task, but on a display lacking distinctive figure–ground borders, and neither of the early components were produced. Results from these experiments suggest sequential stages of processing underlying figure–ground perception, each which are subject to modifications by selective attention. PMID:20146604

The cerebral correlates of subliminal emotions: an eleoencephalographic study with emotional hybrid faces.

PubMed

Prete, Giulia; Capotosto, Paolo; Zappasodi, Filippo; Laeng, Bruno; Tommasi, Luca

2015-12-01

In a high-resolution electroencephalographic study, participants evaluated the friendliness level of upright and inverted 'hybrid faces', i.e. facial photos containing a subliminal emotional core in the low spatial frequencies (< 6 cycles/image), superimposed on a neutral expression in the rest of the spatial frequencies. Upright happy and angry faces were judged as more friendly or less friendly than neutral faces, respectively. We observed the time course of cerebral correlates of these stimuli with event-related potentials (ERPs), confirming that hybrid faces elicited the posterior emotion-related and face-related components (P1, N170 and P2), previously shown to be engaged by non-subliminal emotional stimuli. In addition, these components were stronger in the right hemisphere and were both enhanced and delayed by face inversion. A frontal positivity (210-300 ms) was stronger for emotional than for neutral faces, and for upright than for inverted faces. Hence, hybrid faces represent an original approach in the study of subliminal emotions, which appears promising for investigating their electrophysiological correlates. © 2015 Federation of European Neuroscience Societies and John Wiley & Sons Ltd.

Laser heterodyne surface profiler

DOEpatents

Sommargren, G.E.

1980-06-16

A method and apparatus are disclosed for testing the deviation of the face of an object from a flat smooth surface using a beam of coherent light of two plane-polarized components, one of a frequency constantly greater than the other by a fixed amount to produce a difference frequency with a constant phase to be used as a reference, and splitting the beam into its two components. The separate components are directed onto spaced apart points on the face of the object to be tested for smoothness while the face of the object is rotated on an axis normal to one point, thereby passing the other component over a circular track on the face of the object. The two components are recombined after reflection to produce a reflected frequency difference of a phase proportional to the difference in path length of one component reflected from one point to the other component reflected from the other point. The phase of the reflected frequency difference is compared with the reference phase to produce a signal proportional to the deviation of the height of the surface along the circular track with respect to the fixed point at the center, thereby to produce a signal that is plotted as a profile of the surface along the circular track. The phase detector includes a quarter-wave plate to convert the components of the reference beam into circularly polarized components, a half-wave plate to shift the phase of the circularly polarized components, and a polarizer to produce a signal of a shifted phase for comparison with the phase of the frequency difference of the reflected components detected through a second polarizer. Rotation of the half-wave plate can be used for phase adjustment over a full 360/sup 0/ range.

Maternal exposure to perfluorinated chemicals and reduced fecundity: the MIREC study.

PubMed

Vélez, M P; Arbuckle, T E; Fraser, W D

2015-03-01

What is the effect of maternal exposure to perfluorooctane sulfonate (PFOS), perflurooctanoic acid (PFOA) and perfluorohexane sulfonate (PFHxS) on female fecundity? Increasing concentrations of PFOA or PFHxS in maternal plasma were associated with reduced fecundability and infertility. Perfluorinated chemicals (PFCs) are a group of synthetic compounds used in industrial production. There is a concern about the effect of PFCs on fecundity, as measured by time-to-pregnancy (TTP). Although some recent studies suggest that increasing concentrations of PFCs may decrease fecundity, divergence in the methodological approaches used to evaluate this association have prevented firm conclusions being reached. The Maternal-Infant Research on Environmental Chemicals (MIREC) Study is a cohort study of 2,001 women recruited before 14 weeks of gestation in 10 cities across Canada between 2008 and 2011. A questionnaire was administered and medical chart data and biospecimens were collected from participants. After excluding women who withdrew, those for whom data were incomplete, those whose pregnancies followed birth control failure, and accounting for male fertility, 1743 participants remained. TTP was defined as the number of months of unprotected intercourse needed to become pregnant in the current pregnancy, as self-reported in the first trimester of pregnancy. Plasma concentrations of PFOA, PFOS and PFHxS measured in the first trimester were considered as a surrogate of preconception exposure. Fecundability odds ratios (FORs) were estimated using Cox proportional hazard models for discrete time. FOR < 1 denote a longer TTP and FORs >1 denote a shorter TTP. The odds of infertility (TTP > 12 months or infertility treatment in the index pregnancy) were estimated using logistic regression. Each chemical concentration (ng/ml) was log-transformed and divided by its SD. The cumulative probabilities of pregnancy at 1, 6 and 12 months were 0.42 (95% confidence interval (CI) 0.40-0.45), 0.81 (95% CI 0.79-0.83) and 0.90 (95% CI 0.89-0.92), respectively. The mean maternal age was 32.8 (SD 5.0) years. The geometric means (ng/ml) of PFOA, PFOS and PFHxS were 1.66 (95% CI 1.61-1.71), 4.59 (95% CI 4.46-4.72) and 1.01 (95% CI 0.97-1.05), respectively. After adjustment for potential confounders, PFOA and PFHxS were associated with a 11 and 9% reduction in fecundability per one SD increase (FOR = 0.89; 95% CI 0.83-0.94; P < 0.001 for PFOA and FOR = 0.91; 95% CI 0.86-0.97; P = 0.002 for PFHxS), while no significant association was observed for PFOS (FOR = 0.96; 95% CI 0.91-1.02; P = 0.17). In addition, the odds of infertility increased by 31% per one SD increase of PFOA (odds ratio (OR) = 1.31; 95% CI 1.11-1.53; P = 0.001) and by 27% per one SD increase of PFHxS (OR = 1.27; 95% CI 1.09-1.48; P = 0.003), while no significant association was observed for PFOS (OR = 1.14; 95% CI 0.98-1.34; P = 0.09). Women with the highest concentrations of PFCs might have been excluded from the study if there is a causal association with infertility. The MIREC study did not assess concentrations of PFCs in males, semen quality, menstrual cycle characteristics or intercourse frequency. Our results add to the evidence that exposure to PFOA and PFHxS, even at lower levels than previously reported, may reduce fecundability. The MIREC study is supported by the Chemicals Management Plan of Health Canada, the Canadian Institutes for Health Research (CIHR, grant no. MOP - 81285) and the Ontario Ministry of the Environment. M.P.V. was supported by a CIHR Fellowship Award, and a CIHR-Quebec Training Network in Perinatal Research (QTNPR) Ph.D. scholarship. W.D.F. is supported by a CIHR Canada Research Chair. There are no conflicts of interest to declare. © The Author 2015. Published by Oxford University Press on behalf of the European Society of Human Reproduction and Embryology.

Test-retest reliability of infant event related potentials evoked by faces.

PubMed

Munsters, N M; van Ravenswaaij, H; van den Boomen, C; Kemner, C

2017-04-05

Reliable measures are required to draw meaningful conclusions regarding developmental changes in longitudinal studies. Little is known, however, about the test-retest reliability of face-sensitive event related potentials (ERPs), a frequently used neural measure in infants. The aim of the current study is to investigate the test-retest reliability of ERPs typically evoked by faces in 9-10 month-old infants. The infants (N=31) were presented with neutral, fearful and happy faces that contained only the lower or higher spatial frequency information. They were tested twice within two weeks. The present results show that the test-retest reliability of the face-sensitive ERP components is moderate (P400 and Nc) to substantial (N290). However, there is low test-retest reliability for the effects of the specific experimental manipulations (i.e. emotion and spatial frequency) on the face-sensitive ERPs. To conclude, in infants the face-sensitive ERP components (i.e. N290, P400 and Nc) show adequate test-retest reliability, but not the effects of emotion and spatial frequency on these ERP components. We propose that further research focuses on investigating elements that might increase the test-retest reliability, as adequate test-retest reliability is necessary to draw meaningful conclusions on individual developmental trajectories of the face-sensitive ERPs in infants. Copyright © 2017 The Authors. Published by Elsevier Ltd.. All rights reserved.

Spatial distribution of organic contaminants in three rivers of Southern England bound to suspended particulate material and dissolved in water.

PubMed

Wilkinson, John L; Hooda, Peter S; Swinden, Julian; Barker, James; Barton, Stephen

2017-09-01

The spatial distribution of pharmaceuticals, personal care products (PPCPs) and other emerging contaminants (ECs) such as plasticisers, perflourinated compounds (PFCs) and illicit drug metabolites in water and bound to suspended particulate material (SPM) is not well-understood. Here, we quantify levels of thirteen selected contaminants in water (n=88) and their partition to suspended particulate material (SPM, n=16) in three previously-unstudied rivers of Greater London and Southern England during a key reproduction/spawning period. Analysis was conducted using an in-house validated method for Solid Phase Extraction followed by High-Performance Liquid Chromatography-Tandem Mass-Spectrometry. Analytes were extracted from SPM using an optimised method for ultrasonic-assisted solvent extraction. Detection frequencies of contaminants dissolved in water ranged from 3% (ethinylestradiol) to 100% (bisphenol-A). Overall mean concentrations in the aqueous-phase ranged from 14.7ng/L (benzoylecgonine) to 159ng/L (bisphenol-A). Sewage treatment works (STW) effluent was the predominant source of pharmaceuticals, while plasticisers/perfluorinated compounds may additionally enter rivers via other sources. In SPM, detection frequencies ranged from 44% (PFOA) to 94% (hydroxyacetophenone). Mean quantifiable levels of analytes bound to SPM ranged from 13.5ng/g dry SPM (0.33ng bound/L water) perfluorononanoic acid to 2830ng/g dry SPM (14.3ng bound/L water) perfluorooctanesulfonic acid. Long chain (>C7) amphipathic and acidic PFCs were found to more preferentially bind to SPM than short chain PFCs and other contaminants (Kd=34.1-75.5 vs <5 respectively). Per capita daily contributions of studied contaminants entering rivers ranged from 0.157μg/person/day of benzoylecgonine (cocaine metabolite) to 58.6μg/person/day of bisphenol-A. The large sample size of this work (n=104) enabled ANOVA followed by Tukey HSD post-hoc tests to establish significant trends in PPCP/EC spatial distribution from headwaters through downstream stretches of studied rivers. Novel findings include environmental Kd calculations, the occurrence of contaminants in river headwaters, increases in contaminant metabolite concentrations downstream of STW effluents revealing possible in-river degradation or de-conjugation, the influence of polarity and acidity in the partition of contaminants to particulate-material, among others. Copyright © 2017 The Authors. Published by Elsevier B.V. All rights reserved.

Serum concentrations of perfluorinated compounds (PFC) among selected populations of children and adults in California.

PubMed

Wu, Xiangmei May; Bennett, Deborah H; Calafat, Antonia M; Kato, Kayoko; Strynar, Mark; Andersen, Erik; Moran, Rebecca E; Tancredi, Daniel J; Tulve, Nicolle S; Hertz-Picciotto, Irva

2015-01-01

Perfluorinated compounds (PFCs) have been widely used in industrial applications and consumer products. Their persistent nature and potential health impacts are of concern. Given the high cost of collecting serum samples, this study is to understand whether we can quantify PFC serum concentrations using factors extracted from questionnaire responses and indirect measurements, and whether a single serum measurement can be used to classify an individual's exposure over a one-year period. The study population included three demographic groups: young children (2-8 years old) (N=67), parents of young children (<55 years old) (N=90), and older adults (>55 years old) (N=59). PFC serum concentrations, house dust concentrations, and questionnaires were collected. The geometric mean of perfluorooctane sulfonic acid (PFOS) was highest for the older adults. In contrast, the geometric mean of perfluorooctanoic acid (PFOA) was highest for children. Serum concentrations of the parent and the child from the same family were moderately correlated (Spearman correlation (r)=0.26-0.79, p<0.05), indicating common sources within a family. For adults, age, having occupational exposure or having used fire extinguisher, frequencies of consuming butter/margarine, pork, canned meat entrées, tuna and white fish, freshwater fish, and whether they ate microwave popcorn were significantly positively associated with serum concentrations of individual PFCs. For children, residential dust concentrations, frequency of wearing waterproof clothes, frequency of having canned fish, hotdogs, chicken nuggets, French fries, and chips, and whether they ate microwave popcorn were significant positive predictors of individual PFC serum concentrations. In addition, the serum concentrations collected in a subset of young children (N=20) and the parents (N=42) one year later were strongly correlated (r=0.68-0.98, p<0.001) with the levels measured at the first visits, but showed a decreasing trend. Children had moderate correlation (r=0.43) between serum and dust concentrations of PFOS, indicating indoor sources contribute to exposure. In conclusion, besides food intake, occupational exposure, consumer product use, and exposure to residential dust contribute to PFC exposure. The downward temporal trend of serum concentrations reflects the reduction of PFCs use in recent years while the year-to-year correlation indicates that a single serum measurement could be an estimate of exposure relative to the population for a one-year period in epidemiology studies. Copyright © 2014 Elsevier Inc. All rights reserved.

Determination of adsorbable organic fluorine from aqueous environmental samples by adsorption to polystyrene-divinylbenzene based activated carbon and combustion ion chromatography.

PubMed

Wagner, Andrea; Raue, Brigitte; Brauch, Heinz-Jürgen; Worch, Eckhard; Lange, Frank T

2013-06-21

A new method for the determination of trace levels of adsorbable organic fluorine (AOF) in water is presented. Even if the individual contributing target compounds are widely unknown, this surrogate parameter is suited to identify typical organofluorine contaminations, such as with polyfluorinated chemicals (PFCs), and represents a lower boundary of the organofluorine concentration in water bodies. It consists of the adsorption of organofluorine chemicals on a commercially available synthetic polystyrene-divinylbenzene based activated carbon (AC) followed by analysis of the loaded AC by hydropyrolysis combustion ion chromatography (CIC). Inorganic fluorine is displaced by excess nitrate during the extraction step and by washing the loaded activated carbon with an acidic sodium nitrate solution. Due to its high purity the synthetic AC had a very low and reproducible fluorine blank (0.3 μg/g) compared to natural ACs (up to approximately 9 μg/g). Using this AC, fluoride and the internal standard phosphate could be detected free of chromatographic interferences. With a sample volume of 100 mL and 2× 100 mg of AC packed into two extraction columns combined in series, a limit of quantification (LOQ), derived according to the German standard method DIN 32645, of 0.3 μg/L was achieved. The recoveries of six model PFCs were determined from tap water and a municipal wastewater treatment plant (WWTP) effluent. Except for the extremely polar perfluoroacetic acid (recovery of approximately 10%) the model substances showed fairly good (50% for perfluorobutanoic acid (PFBA)) to very good fluorine recoveries (100±20% for perfluorooctanoic acid (PFOA), perfluorobutanesulfonate (PFBS), 6:2 fluorotelomersulfonate (6:2 FTS)), both from tap water and wastewater matrix. This new analytical protocol was exemplarily applied to several surface water and groundwater samples. The obtained AOF values were compared to the fluorine content of 19 target PFCs analyzed by high performance liquid chromatography-electrospray tandem mass spectrometry (HPLC-(-)ESI-MS/MS). In groundwater contaminated by PFC-containing aqueous film-forming foams (AFFFs) up to 50% of the AOF could be attributed to PFC target chemicals, while in diffuse contaminated samples only <5% of the AOF could be identified by PFC analysis. Copyright © 2013 Elsevier B.V. All rights reserved.

Serum concentrations of perfluorinated compounds (PFC) among selected populations of children and Adults in California

PubMed Central

Wu, Xiangmei (May); Bennett, Deborah H.; Calafat, Antonia M.; Kato, Kayoko; Strynar, Mark; Andersen, Erik; Moran, Rebecca E.; Tancredi, Daniel J.; Tulve, Nicolle S.; Hertz-Picciotto, Irva

2016-01-01

Perfluorinated compounds (PFCs) have been widely used in industrial applications and consumer products. Their persistent nature and potential health impacts are of concern. Given the high cost of collecting serum samples, this study is to understand whether we can quantify PFC serum concentrations using factors extracted from questionnaire responses and indirect measurements, and whether a single serum measurement can be used to classify an individual’s exposure over a one-year period. The study population included three demographic groups: young children (2–8 years old) (N=67), parents of young children (<55 years old) (N=90), and older adults (>55 years old) (N=59). PFC serum concentrations, house dust concentrations, and questionnaires were collected. The geometric mean of perfluorooctane sulfonic acid (PFOS) was highest for the older adults. In contrast, the geometric mean of perfluorooctanoic acid (PFOA) was highest for children. Serum concentrations of the parent and the child from the same family were moderately correlated (Spearman correlation (r)=0.26–0.79, p<0.05), indicating common sources within a family. For adults, age, having occupational exposure or having used fire extinguisher, frequencies of consuming butter/margarine, pork, canned meat entrées, tuna and white fish, freshwater fish, and whether they ate microwave popcorn were significantly positively associated with serum concentrations of individual PFCs. For children, residential dust concentrations, frequency of wearing waterproof clothes, frequency of having canned fish, hotdogs, chicken nuggets, French fries, and chips, and whether they ate microwave popcorn were significant positive predictors of individual PFC serum concentrations. In addition, the serum concentrations collected in a subset of young children (N=20) and the parents (N=42) one year later were strongly correlated (r=0.68–0.98, p<0.001) with the levels measured at the first visits, but showed a decreasing trend. Children had moderate correlation (r=0.43) between serum and dust concentrations of PFOS, indicating indoor sources contribute to exposure. In conclusion, besides food intake, occupational exposure, consumer product use, and exposure to residential dust contribute to PFC exposure. The downward temporal trend of serum concentrations reflects the reduction of PFCs use in recent years while the year-to-year correlation indicates that a single serum measurement could be an estimate of exposure relative to the population for a one-year period in epidemiology studies. PMID:25460645

Perfluorinated compounds in human breast milk from several Asian countries, and in infant formula and dairy milk from the United States.

PubMed

Tao, Lin; Ma, Jing; Kunisue, Tatsuya; Libelo, E Laurence; Tanabe, Shinsuke; Kannan, Kurunthachalam

2008-11-15

The occurrence of perfluorinated compounds (PFCs) in human blood is known to be widespread; nevertheless, the sources of exposure to humans, including infants, are not well understood. In this study, breast milk collected from seven countries in Asia was analyzed (n=184) for nine PFCs, including perfluorooctanesulfonate (PFOS) and perfluorooctanoate (PFOA). In addition, five brands of infant formula (n=21) and 11 brands of dairy milk (n=12) collected from retail stores in the United States were analyzed, for comparison with PFC concentrations previously reported for breast milk from the U.S. PFOS was the predominant PFC detected in almost all Asian breast milk samples, followed by perfluorohexanesulfonate (PFHxS) and PFOA. Median concentrations of PFOS in breast milk from Asian countries varied significantly;the lowest concentration of 39.4 pg/mL was found in India, and the highest concentration of 196 pg/mL was found in Japan. The measured concentrations were similarto or less than the concentrations previously reported from Sweden, the United States, and Germany (median, 106-166 pg/mL). PFHxS was found in more than 70% of the samples analyzed from Japan, Malaysia, Philippines, and Vietnam, at mean concentrations ranging from 6.45 (Malaysia) to 15.8 (Philippines) pg/mL PFOA was found frequently only in samples from Japan; the mean concentration for that country was 77.7 pg/mL. None of the PFCs were detected in the infant-formula or dairy-milk samples from the U.S. except a few samples that contained concentrations close to the limit of detection. The estimated average daily intake of PFOS by infants from seven Asian countries, via breastfeeding, was 11.8 +/- 10.6 ng/kg bw/ day; this value is 7-12 times higher than the estimated adult dietary intakes previously reported from Germany, Canada, and Spain. The average daily intake of PFOA by Japanese infants was 9.6 +/- 4.9 ng/kg bw/day, a value 3-10 times greater than the estimated adult dietary intakes reported from Germany and Canada. The highest estimated daily intakes of PFOS and PFOA by infants from seven Asian countries studied were 1-2 orders of magnitude below the tolerable daily intake values recommended by the U.K. Food Standards Agency.

Inverting faces elicits sensitivity to race on the N170 component: a cross-cultural study.

PubMed

Vizioli, Luca; Foreman, Kay; Rousselet, Guillaume A; Caldara, Roberto

2010-01-29

Human beings are natural experts at processing faces, with some notable exceptions. Same-race faces are better recognized than other-race faces: the so-called other-race effect (ORE). Inverting faces impairs recognition more than for any other inverted visual object: the so-called face inversion effect (FIE). Interestingly, the FIE is stronger for same- compared to other-race faces. At the electrophysiological level, inverted faces elicit consistently delayed and often larger N170 compared to upright faces. However, whether the N170 component is sensitive to race is still a matter of ongoing debate. Here we investigated the N170 sensitivity to race in the framework of the FIE. We recorded EEG from Western Caucasian and East Asian observers while presented with Western Caucasian, East Asian and African American faces in upright and inverted orientations. To control for potential confounds in the EEG signal that might be evoked by the intrinsic and salient differences in the low-level properties of faces from different races, we normalized their amplitude-spectra, luminance and contrast. No differences on the N170 were observed for upright faces. Critically, inverted same-race faces lead to greater recognition impairment and elicited larger N170 amplitudes compared to inverted other-race faces. Our results indicate a finer-grained neural tuning for same-race faces at early stages of processing in both groups of observers.

Levels of perfluorinated acids (PFCAs) in different tissues of Lepidochelys olivacea sea turtles from the Escobilla beach (Oaxaca, Mexico).

PubMed

Pasanisi, Eugenia; Cortés-Gómez, Adriana A; Pérez-López, Marcos; Soler, Francisco; Hernández-Moreno, David; Guerranti, Cristiana; Martellini, Tania; Fuentes-Mascorro, Gisela; Romero, Diego; Cincinelli, Alessandra

2016-12-01

Lepidochelys olivacea is the most abundant and globally distributed sea turtle species in the world and thus, monitoring this species for persistent organic pollutants, such as perfluorinated chemicals, is fundamental for their protection. This study was the first to evaluate the occurrence of five PFCAs (PFOA, PFNA, PFDA, PFUnA, PFDoA) in liver and blood samples of Olive Ridley turtle population from the Escobilla beach (Oaxaca, Mexico). PFDA and PFUnA were the predominant PFCs in blood samples (detected in 93% and 84% of samples, respectively) and were also present in the highest concentrations. Liver samples showed higher PFCA concentrations than whole blood samples, with PFNA and PFDA the most abundant PFCs congeners in liver samples, detected in 65% and 47% of the samples, respectively. The measured levels of contaminants in the blood samples of Lepidochelys olivacea sea turtles were compared to the levels reported in the literature for other turtle species. While linear significant correlations between PFNA, PFDA and PFUnA concentrations in blood samples and curved carapace lengths were determined, no correlation was found for PFOA, supporting the hypothesis that sea turtles could have a higher ability to eliminate this perfluorinated chemical from their blood than other PFCAs. However, we do not know if the concentrations are species or sampling areas dependent. Copyright © 2016 Elsevier B.V. All rights reserved.

Interaction between Social Categories in the Composite Face Paradigm

ERIC Educational Resources Information Center

Chen, Wenfeng; Ren, Naixin; Young, Andrew W.; Liu, Chang Hong

2018-01-01

The composite face paradigm (Young, Hellawell, & Hay, 1987) is widely used to demonstrate holistic perception of faces (Rossion, 2013). In the paradigm, parts from different faces (usually the top and bottom halves) are recombined. The principal criterion for holistic perception is that responses involving the component parts of composites in…

The importance of skin color and facial structure in perceiving and remembering others: an electrophysiological study.

PubMed

Brebner, Joanne L; Krigolson, Olav; Handy, Todd C; Quadflieg, Susanne; Turk, David J

2011-05-04

The own-race bias (ORB) is a well-documented recognition advantage for own-race (OR) over cross-race (CR) faces, the origin of which remains unclear. In the current study, event-related potentials (ERPs) were recorded while Caucasian participants age-categorized Black and White faces which were digitally altered to display either a race congruent or incongruent facial structure. The results of a subsequent surprise memory test indicated that regardless of facial structure participants recognized White faces better than Black faces. Additional analyses revealed that temporally-early ERP components associated with face-specific perceptual processing (N170) and the individuation of facial exemplars (N250) were selectively sensitive to skin color. In addition, the N200 (a component that has been linked to increased attention and depth of encoding afforded to in-group and OR faces) was modulated by color and structure, and correlated with subsequent memory performance. However, the LPP component associated with the cognitive evaluation of perceptual input was influenced by racial differences in facial structure alone. These findings suggest that racial differences in skin color and facial structure are detected during the encoding of unfamiliar faces, and that the categorization of conspecifics as members of our social in-group on the basis of their skin color may be a determining factor in our ability to subsequently remember them. Copyright © 2011 Elsevier B.V. All rights reserved.

Hybrid Course Design: A Different Type of Polymer Blend

ERIC Educational Resources Information Center

Pilcher, Spence C.

2017-01-01

An upper-division undergraduate polymer chemistry course was developed as a blended/hybrid course. The students met face-to-face once a week for 75 min with all other components being available online. Face-to-face meetings were used for class discussions/problem-based lectures, student presentations, hands-on activities, and examinations. Online…

Effects of Online/Face-to-Face Professional Development on College Faculty Perceptions of Disabilities

ERIC Educational Resources Information Center

Buss, Jennifer

2015-01-01

This study was designed to assess the effects of participating in a professional development model that include a face-to-face and online module components. To measure the participants' self-reported knowledge and attitude before and after the professional development would provide information about possible effects of the professional…

Experiment attributes to establish tube with twisted tape insert performance cooling plasma facing components

DOE Office of Scientific and Technical Information (OSTI.GOV)

Clark, Emily; Ramirez, Emilio; Ruggles, Art E.

The modeling capability for tubes with twisted tape inserts is reviewed with reference to the application of cooling plasma facing components in magnetic confinement fusion devices. The history of experiments examining the cooling performance of tubes with twisted tape inserts is reviewed with emphasis on the manner of heating, flow stability limits and the details of the test section and fluid delivery system. Models for heat transfer, burnout, and onset of net vapor generation in straight tube flows and tube with twisted tape are compared. As a result, the gaps in knowledge required to establish performance limits of the plasmamore » facing components are identified and attributes of an experiment to close those gaps are presented.« less

Experiment attributes to establish tube with twisted tape insert performance cooling plasma facing components

DOE PAGES

Clark, Emily; Ramirez, Emilio; Ruggles, Art E.; ...

2015-08-18

The modeling capability for tubes with twisted tape inserts is reviewed with reference to the application of cooling plasma facing components in magnetic confinement fusion devices. The history of experiments examining the cooling performance of tubes with twisted tape inserts is reviewed with emphasis on the manner of heating, flow stability limits and the details of the test section and fluid delivery system. Models for heat transfer, burnout, and onset of net vapor generation in straight tube flows and tube with twisted tape are compared. As a result, the gaps in knowledge required to establish performance limits of the plasmamore » facing components are identified and attributes of an experiment to close those gaps are presented.« less

Probabilistic Elastic Part Model: A Pose-Invariant Representation for Real-World Face Verification.

PubMed

Li, Haoxiang; Hua, Gang

2018-04-01

Pose variation remains to be a major challenge for real-world face recognition. We approach this problem through a probabilistic elastic part model. We extract local descriptors (e.g., LBP or SIFT) from densely sampled multi-scale image patches. By augmenting each descriptor with its location, a Gaussian mixture model (GMM) is trained to capture the spatial-appearance distribution of the face parts of all face images in the training corpus, namely the probabilistic elastic part (PEP) model. Each mixture component of the GMM is confined to be a spherical Gaussian to balance the influence of the appearance and the location terms, which naturally defines a part. Given one or multiple face images of the same subject, the PEP-model builds its PEP representation by sequentially concatenating descriptors identified by each Gaussian component in a maximum likelihood sense. We further propose a joint Bayesian adaptation algorithm to adapt the universally trained GMM to better model the pose variations between the target pair of faces/face tracks, which consistently improves face verification accuracy. Our experiments show that we achieve state-of-the-art face verification accuracy with the proposed representations on the Labeled Face in the Wild (LFW) dataset, the YouTube video face database, and the CMU MultiPIE dataset.

The Neural Correlates of Processing Newborn and Adult Faces in 3-Year-Old Children

ERIC Educational Resources Information Center

Peykarjou, Stefanie; Westerlund, Alissa; Cassia, Viola Macchi; Kuefner, Dana; Nelson, Charles A.

2013-01-01

The current study examines the processing of upright and inverted faces in 3-year-old children (n = 35). Event-related potentials (ERPs) were recorded during a passive looking paradigm including adult and newborn face stimuli. We observed three face-sensitive components, the P1, the N170 and the P400. Inverted faces elicited shorter P1 latency and…

Pleasant and unpleasant odour-face combinations influence face and odour perception: An event-related potential study.

PubMed

Cook, Stephanie; Kokmotou, Katerina; Soto, Vicente; Fallon, Nicholas; Tyson-Carr, John; Thomas, Anna; Giesbrecht, Timo; Field, Matt; Stancak, Andrej

2017-08-30

Odours alter evaluations of concurrent visual stimuli. However, neural mechanisms underlying the effects of congruent and incongruent odours on facial expression perception are not clear. Moreover, the influence of emotional faces on odour perception is not established. We investigated the effects of one pleasant and one unpleasant odour paired with happy and disgusted faces, on subjective ratings and ERP responses to faces. Participants rated the pleasantness of happy and disgusted faces that appeared during 3s pleasant or unpleasant odour pulses, or without odour. Odour pleasantness and intensity ratings were recorded in each trial. EEG was recorded continuously using a 128-channel system. Happy and disgusted faces paired with pleasant and unpleasant odour were rated as more or less pleasant, respectively, compared to the same faces presented in the other odour conditions. Odours were rated as more pleasant when paired with happy faces, and unpleasant odour was rated more intense when paired with disgusted faces. Unpleasant odour paired with disgusted faces also decreased inspiration. Odour-face interactions were evident in the N200 and N400 components. Our results reveal bi-directional effects of odours and faces, and suggest that odour-face interactions may be represented in ERP components. Pairings of unpleasant odour and disgusted faces resulted in stronger hedonic ratings, ERP changes, increased odour intensity ratings and respiratory adjustment. This finding likely represents heightened adaptive responses to multimodal unpleasant stimuli, prompting appropriate behaviour in the presence of danger. Copyright © 2017. Published by Elsevier B.V.

Pancreatic fibrosis calcification and situs inversus in a Liberian female; a case report.

PubMed

Njoh, J; Findley, G; Dharmavaratha, S

1986-06-01

We report the first case of the Pancreatic fibrosis calcification syndrome (PFCS) in a Liberian. The patient presented with the classical features of the syndrome - a history of recurrent abdominal pain, diabetes mellitus, malabsorption and pancreatic calcification on plain abdominal X-ray. The patient also has situs inversus; we believe that this combination is a casual one. Since describing this case, five more cases have been diagnosed; we believe that this condition is not rare in Liberia.

RDT&E for Emerging Contaminants

DTIC Science & Technology

2010-06-01

Perchlorate ● NDMA ● 1,4-Dioxane ● PFCs 8 Perchlorate Issue ● Broad Use & Occurrence  DoD - Rocket propellant - Insensitive munitions  Pyrotechnics and...and 18O -20 -15 -10 -5.0 0.0 5.0 -30 -25 -20 -15 -10 -5 0 5 10 Laboratory Military Natural Herbicides Gunpowder Road Flares Taiwan 3 7 C l 18 O 27 NDMA ...Toxicology  NDMA is a potent mutagen, teratogen, & carcinogen.  EPA 10-6 Lifetime Cancer Risk = 0.7 ng/L.  California DHS; 10 ng/L Action

With the Mountain Men: Co-Operation and Competition within the Context of Cohort

DTIC Science & Technology

1988-05-01

fireteam leader positions had been filled with selected, but brand new, OSUT graduates. PFCs. An hour’s discussion under an afternoon oak tree with a...every single trooper, six months out on the "real Army" side of OSUT, was the will, enthusiasm, and optimism of a brand -new soldier 2 days out of AIT or...ragged decline, never again reaching the high-point of a freshly-trained, brand -new soldier. The unusual phenomenon I was watching inside that

Dissociation between the neural correlates of conscious face perception and visual attention.

PubMed

Navajas, Joaquin; Nitka, Aleksander W; Quian Quiroga, Rodrigo

2017-08-01

Given the higher chance to recognize attended compared to unattended stimuli, the specific neural correlates of these two processes, attention and awareness, tend to be intermingled in experimental designs. In this study, we dissociated the neural correlates of conscious face perception from the effects of visual attention. To do this, we presented faces at the threshold of awareness and manipulated attention through the use of exogenous prestimulus cues. We show that the N170 component, a scalp EEG marker of face perception, was modulated independently by attention and by awareness. An earlier P1 component was not modulated by either of the two effects and a later P3 component was indicative of awareness but not of attention. These claims are supported by converging evidence from (a) modulations observed in the average evoked potentials, (b) correlations between neural and behavioral data at the single-subject level, and (c) single-trial analyses. Overall, our results show a clear dissociation between the neural substrates of attention and awareness. Based on these results, we argue that conscious face perception is triggered by a boost in face-selective cortical ensembles that can be modulated by, but are still independent from, visual attention. © 2017 Society for Psychophysiological Research.

Creation and Assessment of an Active e-Learning Introductory Geology Course

NASA Astrophysics Data System (ADS)

Sit, Stefany M.; Brudzinski, Michael R.

2017-12-01

The recent emphasis in higher education on both student engagement and online learning encouraged the authors to develop an active e-learning environment for an introductory geohazards course, which enrolls 70+ undergraduate students per semester. Instructors focused on replicating the achievements and addressing the challenges within an already established face-to-face student-centered class (Brudzinski and Sikorski 2010; Sit 2013). Through the use of a learning management system (LMS) and other available technologies, a wide range of course components were developed including online homework assignments with automatic grading and tailored feedback, video tutorials of software programs like Google Earth and Microsoft Excel, and more realistic scientific investigations using authentic and freely available data downloaded from the internet. The different course components designed to engage students and improve overall student learning and development were evaluated using student surveys and instructor reflection. Each component can be used independently and intertwined into a face-to-face course. Results suggest that significant opportunities are available in an online environment including the potential for improved student performance and new datasets for educational research. Specifically, results from pre and post-semester Geoscience Concept Inventory (GCI) testing in an active e-learning course show enhanced student learning gains compared to face-to-face lecture-based and student-centered courses.

Still feeling it: the time course of emotional recovery from an attentional perspective

PubMed Central

Morriss, Jayne; Taylor, Alexander N. W.; Roesch, Etienne B.; van Reekum, Carien M.

2013-01-01

Emotional reactivity and the time taken to recover, particularly from negative, stressful, events, are inextricably linked, and both are crucial for maintaining well-being. It is unclear, however, to what extent emotional reactivity during stimulus onset predicts the time course of recovery after stimulus offset. To address this question, 25 participants viewed arousing (negative and positive) and neutral pictures from the International Affective Picture System (IAPS) followed by task-relevant face targets, which were to be gender categorized. Faces were presented early (400–1500 ms) or late (2400–3500 ms) after picture offset to capture the time course of recovery from emotional stimuli. Measures of reaction time (RT), as well as face-locked N170 and P3 components were taken as indicators of the impact of lingering emotion on attentional facilitation or interference. Electrophysiological effects revealed negative and positive images to facilitate face-target processing on the P3 component, regardless of temporal interval. At the individual level, increased reactivity to: (1) negative pictures, quantified as the IAPS picture-locked Late Positive Potential (LPP), predicted larger attentional interference on the face-locked P3 component to faces presented in the late time window after picture offset. (2) Positive pictures, denoted by the LPP, predicted larger facilitation on the face-locked P3 component to faces presented in the earlier time window after picture offset. These results suggest that subsequent processing is still impacted up to 3500 ms after the offset of negative pictures and 1500 ms after the offset of positive pictures for individuals reacting more strongly to these pictures, respectively. Such findings emphasize the importance of individual differences in reactivity when predicting the temporality of emotional recovery. The current experimental model provides a novel basis for future research aiming to identify profiles of adaptive and maladaptive recovery. PMID:23734116

Sub-component modeling for face image reconstruction in video communications

NASA Astrophysics Data System (ADS)

Shiell, Derek J.; Xiao, Jing; Katsaggelos, Aggelos K.

2008-08-01

Emerging communications trends point to streaming video as a new form of content delivery. These systems are implemented over wired systems, such as cable or ethernet, and wireless networks, cell phones, and portable game systems. These communications systems require sophisticated methods of compression and error-resilience encoding to enable communications across band-limited and noisy delivery channels. Additionally, the transmitted video data must be of high enough quality to ensure a satisfactory end-user experience. Traditionally, video compression makes use of temporal and spatial coherence to reduce the information required to represent an image. In many communications systems, the communications channel is characterized by a probabilistic model which describes the capacity or fidelity of the channel. The implication is that information is lost or distorted in the channel, and requires concealment on the receiving end. We demonstrate a generative model based transmission scheme to compress human face images in video, which has the advantages of a potentially higher compression ratio, while maintaining robustness to errors and data corruption. This is accomplished by training an offline face model and using the model to reconstruct face images on the receiving end. We propose a sub-component AAM modeling the appearance of sub-facial components individually, and show face reconstruction results under different types of video degradation using a weighted and non-weighted version of the sub-component AAM.

Inversion and contrast polarity reversal affect both encoding and recognition processes of unfamiliar faces: a repetition study using ERPs.

PubMed

Itier, Roxane J; Taylor, Margot J

2002-02-01

Using ERPs in a face recognition task, we investigated whether inversion and contrast reversal, which seem to disrupt different aspects of face configuration, differentially affected encoding and memory for faces. Upright, inverted, and negative (contrast-reversed) unknown faces were either immediately repeated (0-lag) or repeated after 1 intervening face (1-lag). The encoding condition (new) consisted of the first presentation of items correctly recognized in the two repeated conditions. 0-lag faces were recognized better and faster than 1-lag faces. Inverted and negative pictures elicited longer reaction times, lower hit rates, and higher false alarm rates than upright faces. ERP analyses revealed that negative and inverted faces affected both early (encoding) and late (recognition) stages of face processing. Early components (N170, VPP) were delayed and enhanced by both inversion and contrast reversal which also affected P1 and P2 components. Amplitudes were higher for inverted faces at frontal and parietal sites from 350 to 600 ms. Priming effects were seen at encoding stages, revealed by shorter latencies and smaller amplitudes of N170 for repeated stimuli, which did not differ depending on face type. Repeated faces yielded more positive amplitudes than new faces from 250 to 450 ms frontally and from 400 to 600 ms parietally. However, ERP differences revealed that the magnitude of this repetition effect was smaller for negative and inverted than upright faces at 0-lag but not at 1-lag condition. Thus, face encoding and recognition processes were affected by inversion and contrast-reversal differently.

Influence of socio-economic status on access to different components of SCI management across Indian population.

PubMed

Chhabra, H S; Bhalla, A M

2015-11-01

To assess the influence of financial constraints on access to different components of spinal cord injury (SCI) management in various socio-economic strata of the Indian population. Indian Spinal Injuries Centre (ISIC). One hundred fifty SCI individuals who came for follow-up at ISIC between March 2009 and March 2013 with at least 1 year of community exposure after discharge were included in the study. Socio-economic classification was carried out according to the Kuppuswamy scale, a standard scale for the Indian population. A self-designed questionnaire was administered. No sample was available from the lower group. There was a statistically significant difference (P<0.05) for the levels of difficulty perceived by different socio-economic groups in accessing different components of SCI management. Aided upper lower group was dependent on welfare schemes for in-hospital treatment but could not access other components of management once discharged. Unaided upper lower group either faced severe difficulty or could not access management. Majority of lower middle group faced severe difficulty. Upper middle group was equally divided into facing severe, moderate or no difficulty. Most patients in the upper group faced no difficulty, whereas some faced moderate and a small number of severe difficulty. Financial constraints affected all components of SCI management in all except the upper group. The results of the survey suggest that a very large percentage of the Indian population would find it difficult to access comprehensive SCI management and advocate extension of essential medical coverage to unaided upper lower, lower middle and upper middle groups.

High heat flux issues for plasma-facing components in fusion reactors

NASA Astrophysics Data System (ADS)

Watson, Robert D.

1993-02-01

Plasma facing components in tokamak fusion reactors are faced with a number of difficult high heat flux issues. These components include: first wall armor tiles, pumped limiters, diverter plates, rf antennae structure, and diagnostic probes. Peak heat fluxes are 15 - 30 MW/m2 for diverter plates, which will operate for 100 - 1000 seconds in future tokamaks. Disruption heat fluxes can approach 100,000 MW/m2 for 0.1 ms. Diverter plates are water-cooled heat sinks with armor tiles brazed on to the plasma facing side. Heat sink materials include OFHC, GlidcopTM, TZM, Mo-41Re, and niobium alloys. Armor tile materials include: carbon fiber composites, beryllium, silicon carbide, tungsten, and molybdenum. Tile thickness range from 2 - 10 mm, and heat sinks are 1 - 3 mm. A twisted tape insert is used to enhance heat transfer and increase the burnout safety margin from critical heat flux limits to 50 - 60 MW/m2 with water at 10 m/s and 4 MPa. Tests using rastered electron beams have shown thermal fatigue failures from cracks at the brazed interface between tiles and the heat sink after only 1000 cycles at 10 - 15 MW/m2. These fatigue lifetimes need to be increased an order of magnitude to meet future requirements. Other critical issues for plasma facing components include: surface erosion from sputtering and disruption erosion, eddy current forces and runaway electron impact from disruptions, neutron damage, tritium retention and release, remote maintenance of radioactive components, corrosion-erosion, and loss-of-coolant accidents.

Can Holistic Processing Be Learned for Inverted Faces?

ERIC Educational Resources Information Center

Robbins, Rachel; McKone, Elinor

2003-01-01

The origin of "special" processing for upright faces has been a matter of ongoing debate. If it is due to generic expertise, as opposed to having some innate component, holistic processing should be learnable for stimuli other than upright faces. Here we assess inverted faces. We trained subjects to discriminate identical twins using up to 1100…

Impression Management in Kindergarten Classrooms: An Analysis of Children's Face-Work in Peer Interactions.

ERIC Educational Resources Information Center

Hatch, J. Amos

A systematic analysis was made of the communications of 5- and 6-year-old children in two kindergarten classrooms to discover whether children's face-to-face interactions with peers included "face work" components (rituals through which individuals manage impressions when it becomes difficult to maintain a social situation) and, if so,…

Encapsulated Presentation: A New Paradigm of Blended Learning

ERIC Educational Resources Information Center

Rose, Richard; Ray, Jan

2011-01-01

This article is a presentation of a new mode of blended learning whose only goal is to enrich the quality of instruction in the face-to-face classroom through the simultaneous delivery of online and face-to-face components. Encapsulated presentation is the delivery of the entire presentation phase of a lesson in the classroom by electronic methods…

Do Faces Capture the Attention of Individuals with Williams Syndrome or Autism? Evidence from Tracking Eye Movements

ERIC Educational Resources Information Center

Riby, Deborah M.; Hancock, Peter J. B.

2009-01-01

The neuro-developmental disorders of Williams syndrome (WS) and autism can reveal key components of social cognition. Eye-tracking techniques were applied in two tasks exploring attention to pictures containing faces. Images were (i) scrambled pictures containing faces or (ii) pictures of scenes with embedded faces. Compared to individuals who…

Online or Face-to-Face? Students' Experiences and Preferences in E-Learning

ERIC Educational Resources Information Center

Paechter, Manuela; Maier, Brigitte

2010-01-01

Which aspects of e-learning courses do students experience as being favorable for learning? When do students prefer online or face-to-face learning components? These questions were the subject of a research study in a sample of 2196 students from 29 Austrian universities. The students completed a questionnaire on their experiences attending an…

Tritium Plasma Experiment Upgrade and Improvement of Surface Diagnostic Capabilities at STAR Facility for Enhancing Tritium and Nuclear PMI Sciences

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shimada, M.; Taylor, C. N.; Pawelko, R. J.

2016-04-01

The Tritium Plasma Experiment (TPE) is a unique high-flux linear plasma device that can handle beryllium, tritium, and neutron-irradiated plasma facing materials, and is the only existing device dedicated to directly study tritium retention and permeation in neutron-irradiated materials with tritium [M. Shimada et.al., Rev. Sci. Instru. 82 (2011) 083503 and and M. Shimada, et.al., Nucl. Fusion 55 (2015) 013008]. The plasma-material-interaction (PMI) determines a boundary condition for diffusing tritium into bulk PFCs, and the tritium PMI is crucial for enhancing fundamental sciences that dictate tritium fuel cycles and safety and are high importance to an FNSF and DEMO. Recentlymore » the TPE has undergone major upgrades in its electrical and control systems. New DC power supplies and a new control center enable remote plasma operations from outside of the contamination area for tritium, minimizing the possible exposure risk with tritium and beryllium. We discuss the electrical upgrade, enhanced operational safety, improved plasma performance, and development of optical spectrometer system. This upgrade not only improves operational safety of the worker, but also enhances plasma performance to better simulate extreme plasma-material conditions expected in ITER, Fusion Nuclear Science Facility (FNSF), and Demonstration reactor (DEMO). This work was prepared for the U.S. Department of Energy, Office of Fusion Energy Sciences, under the DOE Idaho Field Office contract number DE-AC07-05ID14517.« less

Retaining Critical Therapeutic Elements of Behavioral Interventions Translated For Delivery via the Internet: Recommendations and an Example Using Pain Coping Skills Training

PubMed Central

Porter, Laura S; Somers, Tamara J; McKee, Daphne C; Keefe, Francis J

2014-01-01

Evidence supporting the efficacy of behavioral interventions based on principles of cognitive behavioral therapies has spurred interest in translating these interventions for delivery via the Internet. However, the benefits of this dissemination method cannot be realized unless the translated interventions are as effective as possible. We describe a challenge that must be overcome to ensure this occurs—Internet interventions must retain therapeutic components and processes underlying the success of face-to-face interventions on which they are based. These components and processes vary in the ease with which they can be translated to the online environment. Moreover, some are subtle and may be overlooked, despite being recognized as essential to the success of face-to-face interventions. We provide preliminary guidance for retaining critical therapeutic components and processes in the translation process, using Pain Coping Skills Training for osteoarthritis pain to illustrate methods. Directions for future research are also discussed. PMID:25532216

Single-unit activity during natural vision: diversity, consistency, and spatial sensitivity among AF face patch neurons.

PubMed

McMahon, David B T; Russ, Brian E; Elnaiem, Heba D; Kurnikova, Anastasia I; Leopold, David A

2015-04-08

Several visual areas within the STS of the macaque brain respond strongly to faces and other biological stimuli. Determining the principles that govern neural responses in this region has proven challenging, due in part to the inherently complex stimulus domain of dynamic biological stimuli that are not captured by an easily parameterized stimulus set. Here we investigated neural responses in one fMRI-defined face patch in the anterior fundus (AF) of the STS while macaques freely view complex videos rich with natural social content. Longitudinal single-unit recordings allowed for the accumulation of each neuron's responses to repeated video presentations across sessions. We found that individual neurons, while diverse in their response patterns, were consistently and deterministically driven by the video content. We used principal component analysis to compute a family of eigenneurons, which summarized 24% of the shared population activity in the first two components. We found that the most prominent component of AF activity reflected an interaction between visible body region and scene layout. Close-up shots of faces elicited the strongest neural responses, whereas far away shots of faces or close-up shots of hindquarters elicited weak or inhibitory responses. Sensitivity to the apparent proximity of faces was also observed in gamma band local field potential. This category-selective sensitivity to spatial scale, together with the known exchange of anatomical projections of this area with regions involved in visuospatial analysis, suggests that the AF face patch may be specialized in aspects of face perception that pertain to the layout of a social scene.

Stepwise emergence of the face-sensitive N170 event-related potential component.

PubMed

Jemel, Boutheina; Schuller, Anne-Marie; Cheref-Khan, Yasémine; Goffaux, Valérie; Crommelinck, Marc; Bruyer, Raymond

2003-11-14

The present study used a parametric design to characterize early event-related potentials (ERP) to face stimuli embedded in gradually decreasing random noise levels. For both N170 and the vertex positive potential (VPP) there was a linear increase in amplitude and decrease in latency with decreasing levels of noise. In contrast, the earlier visual P1 component was stable across noise levels. The P1/N170 dissociation suggests not only a functional dissociation between low and high-level visual processing of faces but also that the N170 reflects the integration of sensorial information into a unitary representation. In addition, the N170/VPP association supports the view that they reflect the same processes operating when viewing faces.

Fixation to features and neural processing of facial expressions in a gender discrimination task

PubMed Central

Neath, Karly N.; Itier, Roxane J.

2017-01-01

Early face encoding, as reflected by the N170 ERP component, is sensitive to fixation to the eyes. Whether this sensitivity varies with facial expressions of emotion and can also be seen on other ERP components such as P1 and EPN, was investigated. Using eye-tracking to manipulate fixation on facial features, we found the N170 to be the only eye-sensitive component and this was true for fearful, happy and neutral faces. A different effect of fixation to features was seen for the earlier P1 that likely reflected general sensitivity to face position. An early effect of emotion (~120 ms) for happy faces was seen at occipital sites and was sustained until ~350 ms post-stimulus. For fearful faces, an early effect was seen around 80 ms followed by a later effect appearing at ~150 ms until ~300 ms at lateral posterior sites. Results suggests that in this emotion-irrelevant gender discrimination task, processing of fearful and happy expressions occurred early and largely independently of the eye-sensitivity indexed by the N170. Processing of the two emotions involved different underlying brain networks active at different times. PMID:26277653