The effects of ballast on the sound radiation from railway track

NASA Astrophysics Data System (ADS)

Zhang, Xianying; Thompson, David; Jeong, Hongseok; Squicciarini, Giacomo

2017-07-01

In a conventional railway track, the rails are laid on sleepers, usually made of concrete, which are supported by a layer of coarse stones known as ballast. This paper focuses on quantifying the influence that the ballast has on the noise produced by the vibration of the track, particularly on the rail and sleeper radiation ratios. A one-fifth scale model of a railway track has been used to conduct acoustic and vibration measurements. This includes reduced-scale ballast that has been produced with stone sizes in the correct proportions. Two different scaling factors (1:√5 and 1:5) have been adopted for the stone sizes in an attempt to reproduce approximately the acoustic properties of full-scale ballast. It is shown that, although a scale factor of 1:√5 gives a better scaling of the acoustic properties, the stones scaled at 1:5 also give acceptable results. The flow resistivity and porosity of this ballast sample have been measured. These have been used in a local reaction model based on the Johnson-Allard formulation to predict the ballast absorption, showing good agreement with measurements of the absorption coefficient. The effects of the presence of the ballast on the noise radiation from a reduced-scale steel rail and concrete sleeper have been investigated experimentally with the ballast located on a rigid foundation. Comparisons are made with the corresponding numerical predictions obtained by using the boundary element method, in which the ballast is represented by a surface impedance. Additionally the finite element method has been used in which the porous medium is considered as an equivalent fluid. From these results it is shown that the extended reaction model gives better agreement with the measurements. Finally, the effects of the ballast vibration on the sleeper radiation have also been investigated for a case of three sleepers embedded in ballast. The ballast vibration is shown to increase the sound radiation by between 1 and 4.5 dB for

Development and optimization of a matrix converter supplying an electronic ballast - UV lamp system for water sterilization

NASA Astrophysics Data System (ADS)

Bokhtache, Aicha Aissa; Zegaoui, Abdallah; Aillerie, Michel; Djahbar, Abdelkader; Hemici, Kheira

2018-05-01

Electronic ballasts dedicated to discharge lamps allow improving the quality of radiation by operating at high frequency. In the present work, the use of a single-phase direct converter with a matrix structure for supplying a low-pressure mercury-argon UVC lamp for water sterilization is proposed. The structure of the converter is based on two switching cells allowing the realization of a fully controllable bidirectional switches. The advantages of such a matrix topology include the delivered of a sinusoidal waveform current with a controllable power factor close to unity, variable in amplitude and frequency. In order to obtain the desired amplitude and frequency, a PWM control was associated in the current realization. Finally, a linear adjustment of the lamp arc current was warranted by using of a PI regulator.

46 CFR 119.540 - Ballast systems.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 4 2013-10-01 2013-10-01 false Ballast systems. 119.540 Section 119.540 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) SMALL PASSENGER VESSELS CARRYING MORE THAN 150... Ballast Systems § 119.540 Ballast systems. Solid and water ballast must comply with the requirements of...

46 CFR 182.540 - Ballast systems.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 7 2014-10-01 2014-10-01 false Ballast systems. 182.540 Section 182.540 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) SMALL PASSENGER VESSELS (UNDER 100 GROSS TONS) MACHINERY INSTALLATION Bilge and Ballast Systems § 182.540 Ballast systems. (a) Ballast piping must not be...

46 CFR 119.540 - Ballast systems.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 4 2012-10-01 2012-10-01 false Ballast systems. 119.540 Section 119.540 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) SMALL PASSENGER VESSELS CARRYING MORE THAN 150... Ballast Systems § 119.540 Ballast systems. Solid and water ballast must comply with the requirements of...

46 CFR 119.540 - Ballast systems.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 4 2011-10-01 2011-10-01 false Ballast systems. 119.540 Section 119.540 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) SMALL PASSENGER VESSELS CARRYING MORE THAN 150... Ballast Systems § 119.540 Ballast systems. Solid and water ballast must comply with the requirements of...

46 CFR 182.540 - Ballast systems.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 7 2013-10-01 2013-10-01 false Ballast systems. 182.540 Section 182.540 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) SMALL PASSENGER VESSELS (UNDER 100 GROSS TONS) MACHINERY INSTALLATION Bilge and Ballast Systems § 182.540 Ballast systems. (a) Ballast piping must not be...

46 CFR 182.540 - Ballast systems.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 7 2010-10-01 2010-10-01 false Ballast systems. 182.540 Section 182.540 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) SMALL PASSENGER VESSELS (UNDER 100 GROSS TONS) MACHINERY INSTALLATION Bilge and Ballast Systems § 182.540 Ballast systems. (a) Ballast piping must not be...

14 CFR 31.51 - Ballast.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Ballast. 31.51 Section 31.51 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT AIRWORTHINESS... means for the safe storage and controlled release of ballast. The ballast must consist of material that...

14 CFR 31.51 - Ballast.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Ballast. 31.51 Section 31.51 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT AIRWORTHINESS... means for the safe storage and controlled release of ballast. The ballast must consist of material that...

46 CFR 178.510 - Ballast.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 7 2012-10-01 2012-10-01 false Ballast. 178.510 Section 178.510 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) SMALL PASSENGER VESSELS (UNDER 100 GROSS TONS) INTACT STABILITY AND SEAWORTHINESS Special Installations § 178.510 Ballast. (a) Any solid fixed ballast used to comply...

46 CFR 178.510 - Ballast.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 7 2014-10-01 2014-10-01 false Ballast. 178.510 Section 178.510 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) SMALL PASSENGER VESSELS (UNDER 100 GROSS TONS) INTACT STABILITY AND SEAWORTHINESS Special Installations § 178.510 Ballast. (a) Any solid fixed ballast used to comply...

Identification of ballast water discharge profiles of a port to enable effective ballast water management and environmental studies

NASA Astrophysics Data System (ADS)

David, Matej; Gollasch, Stephan; Penko, Ludvik

2018-03-01

Information about the profile of ballast water discharges in a port is one of the basic elements of the decision making process in ballast water risk assessment and management, and supports the evaluation of dimensions and processes of aquatic species invasions with vessels ballast water. In the lack of ballast water reporting, ballast water discharge assessments need to be conducted. In this study we have assessed and compared ballast water discharge profiles of two ports with different maritime traffic and cargo profiles, the Port of Hamburg (Germany) and the Muuga Harbour, Port of Tallinn (Estonia). This study shows methods and approaches which can be used to assess volumes and donor ports of ballast water discharges for a port at the level of each vessel call. These methods and approaches can be applied to any port to support the implementation of feasible and efficient ballast water management measures and to enable environmental studies including long-term accumulation risks of disinfection by-products from ballast water management systems making use of active substances, as well as for discharges of other chemical compounds.

Challenges in global ballast water management.

PubMed

Endresen, Øyvind; Lee Behrens, Hanna; Brynestad, Sigrid; Bjørn Andersen, Aage; Skjong, Rolf

2004-04-01

Ballast water management is a complex issue raising the challenge of merging international regulations, ship's specific configurations along with ecological conservation. This complexity is illustrated in this paper by considering ballast water volume, discharge frequency, ship safety and operational issues aligned with regional characteristics to address ecological risk for selected routes. A re-estimation of ballast water volumes gives a global annual level of 3500 Mton. Global ballast water volume discharged into open sea originating from ballast water exchange operations is estimated to approximately 2800 Mton. Risk based decision support systems coupled to databases for different ports and invasive species characteristics and distributions can allow for differentiated treatment levels while maintaining low risk levels. On certain routes, the risk is estimated to be unacceptable and some kind of ballast water treatment or management should be applied.

Mechanics of Ballast Compaction. Volume 2 : Field Methods for Ballast Physical State Measurement

DOT National Transportation Integrated Search

1982-03-01

Field methods for measuring ballast physical state are needed to study the effects of ballast compaction. Following a consideration of various alternatives, three methods were selected for development and evaluation. The first was in-place density, w...

33 CFR 151.1510 - Ballast water management.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 33 Navigation and Navigable Waters 2 2011-07-01 2011-07-01 false Ballast water management. 151..., AND BALLAST WATER Ballast Water Management for Control of Nonindigenous Species in the Great Lakes and Hudson River § 151.1510 Ballast water management. (a) The master of each vessel subject to this subpart...

33 CFR 151.1510 - Ballast water management.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Ballast water management. 151..., AND BALLAST WATER Ballast Water Management for Control of Nonindigenous Species in the Great Lakes and Hudson River § 151.1510 Ballast water management. (a) The master of each vessel subject to this subpart...

Ballasted photovoltaic module and module arrays

DOEpatents

Botkin, Jonathan [El Cerrito, CA; Graves, Simon [Berkeley, CA; Danning, Matt [Oakland, CA

2011-11-29

A photovoltaic (PV) module assembly including a PV module and a ballast tray. The PV module includes a PV device and a frame. A PV laminate is assembled to the frame, and the frame includes an arm. The ballast tray is adapted for containing ballast and is removably associated with the PV module in a ballasting state where the tray is vertically under the PV laminate and vertically over the arm to impede overt displacement of the PV module. The PV module assembly can be installed to a flat commercial rooftop, with the PV module and the ballast tray both resting upon the rooftop. In some embodiments, the ballasting state includes corresponding surfaces of the arm and the tray being spaced from one another under normal (low or no wind) conditions, such that the frame is not continuously subjected to a weight of the tray.

Identification of high-speed rail ballast flight risk factors and risk mitigation strategies - final report.

DOT National Transportation Integrated Search

2015-04-01

The phenomenon of flying ballast is well-documented in high-speed rail operations. Displaced ballast particles from the track bed : may cause damage to rolling stock as well as the track infrastructure, and wayside structures close to the right of wa...

Detection of Ballast Damage by In-Situ Vibration Measurement of Sleepers

NASA Astrophysics Data System (ADS)

Lam, H. F.; Wong, M. T.; Keefe, R. M.

2010-05-01

Ballasted track is one of the most important elements of railway transportation systems worldwide. Owing to its importance in railway safety, many monitoring and evaluation methods have been developed. Current railway track monitoring systems are comprehensive, fast and efficient in testing railway track level and alignment, rail gauge, rail corrugation, etc. However, the monitoring of ballast condition still relies very much on visual inspection and core tests. Although extensive research has been carried out in the development of non-destructive methods for ballast condition evaluation, a commonly accepted and cost-effective method is still in demand. In Hong Kong practice, if abnormal train vibration is reported by the train operator or passengers, permanent way inspectors will locate the problem area by track geometry measurement. It must be pointed out that visual inspection can only identify ballast damage on the track surface, the track geometry deficiencies and rail twists can be detected using a track gauge. Ballast damage under the sleeper loading area and the ballast shoulder, which are the main factors affecting track stability and ride quality, are extremely difficult if not impossible to be detected by visual inspection. Core test is a destructive test, which is expensive, time consuming and may be disruptive to traffic. A fast real-time ballast damage detection method that can be implemented by permanent way inspectors with simple equipment can certainly provide valuable information for engineers in assessing the safety and riding quality of ballasted track systems. The main objective of this paper is to study the feasibility in using the vibration characteristics of sleepers in quantifying the ballast condition under the sleepers, and so as to explore the possibility in developing a handy method for the detection of ballast damage based on the measured vibration of sleepers.

Management and environmental risk study of the physicochemical parameters of ballast water.

PubMed

Nosrati-Ghods, Nosaibeh; Ghadiri, Mehdi; Früh, Wolf-Gerrit

2017-01-15

Shipping is a vital industry for the global economy. Stability of ships, provided by ballast water, is a crucial factor for cargo loading and unloading processes. Ballast water treatment has practical significance in terms of environmental issues, ecosystem, and human health, because ships discharge this water into the environment before loading their cargos. This study reviews the common methods for ballast water management - exchange, heating, filtration, ultrasonic treatment, ultraviolet irradiation, chemicals, and gas supersaturation - to select the best one. This study compares water temperature, salinity, dissolved oxygen, polycyclic aromatic hydrocarbons (PAHs), and heavy metals (Co, Cr, Ni, Pb) for ballast tanks of selected ships with the recipient port environment in the Persian Gulf as a case study. The exchange of ballast water in the ocean and/or its treatment on board to prevent inadvertent effects on the environment's physicochemical conditions is related to vessel characteristics, legislation, and the environmental condition. Ecological risk study showed that the salt content in ballast water is close to that of seawater, but the values of Cr (2.1mg/l) and Ni (0.029mg/l) in ballast water are higher than those in seawater (1 and 0.004mg/l, respectively). Copyright © 2016 Elsevier Ltd. All rights reserved.

Mechanics of Ballast Compaction. Volume 1 : Technical Review of Ballast Compaction and Related Topics

DOT National Transportation Integrated Search

1982-03-01

The purpose of the research program on the mechanics of ballast compaction is to determine the influence of mechanical compaction on the ballast physical state and its consequence on the performance of the track structure. This report, which is one o...

Properties of fouled railroad ballast (phase 1).

DOT National Transportation Integrated Search

2012-10-01

Ballasted tracks are the most common tracks used in the railroad industry and are designed to provide a stable, safe, and efficient rail : foundation. A ballasted track consists of superstructure (ties, fasteners, and rails) and substructure (ballast...

33 CFR 151.1510 - Ballast water management requirements.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 33 Navigation and Navigable Waters 2 2013-07-01 2013-07-01 false Ballast water management... COMMERCIAL WASTE, AND BALLAST WATER Ballast Water Management for Control of Nonindigenous Species in the Great Lakes and Hudson River § 151.1510 Ballast water management requirements. (a) The master of each...

46 CFR 178.510 - Ballast.

Code of Federal Regulations, 2010 CFR

2010-10-01

... that prevents shifting of the ballast; and (2) Installed to the satisfaction of the cognizant OCMI. (b... repair if it is replaced to the satisfaction of the OCMI. (d) Water ballast, either as an active system...

Application of geocomposite placed beneath ballast bed to improve ballast quality and track stability

NASA Astrophysics Data System (ADS)

Horníček, Leoš; Břešt'ovský, Petr; Jasanský, Petr

2017-09-01

The article deals with the application of a stabilization hexagonal geocomposite for the improvement of poor stability of railway tracks caused by undesirable migration of fine soil particles from the subgrade into the ballast bed. The establishment of a test railway section on a single-line track situated near Domazlice and its long-term monitoring programme are described. Evaluation is aimed especially at track geometry parameters, the load-bearing capacity of the ballast bed, elastic rail deflection during train passages and the durability of geocomposite’s physical properties. The data taken from the test section during five measurement campaigns are compared with both adjacent sections. In one of them, only the ballast bed renovation was carried out, whereas in the second one no intervention was performed at all. The usage of a pioneering geosynthetic product in combination with new trends in ballast bed restoration seems to be an innovative as well as effective solution to analogous problematic spots on railway tracks in the Czech Republic.

Ballast water research at the WFRC

USGS Publications Warehouse

Thorsteinson, Lyman

2006-01-01

Invasive aquatic species are considered to be one of the greatest threats to marine biodiversity, coastal economies, and even human health. Ballast water is a primary vector for these bioinvasions. One method of reducing risk of ballast water introductions is mid-ocean exchange of marine ballast water. However, it is widely recognized that this practice has many limitations, including serious ship safety concerns and variable biological effectiveness. International agencies and federal, state and local governments are attempting to tackle the problem by recommending or mandating the installation of ballast water treatment systems. The WFRC is working with others to develop new technologies to detect, prevent, and control aquatic invasive species impacts in Puget Sound and the Pacific Northwest.

10 CFR 429.26 - Fluorescent lamp ballasts.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 10 Energy 3 2014-01-01 2014-01-01 false Fluorescent lamp ballasts. 429.26 Section 429.26 Energy... COMMERCIAL AND INDUSTRIAL EQUIPMENT Certification § 429.26 Fluorescent lamp ballasts. (a) Sampling plan for selection of units for testing. (1) The requirements of § 429.11 are applicable to fluorescent lamp ballasts...

10 CFR 429.26 - Fluorescent lamp ballasts.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 10 Energy 3 2012-01-01 2012-01-01 false Fluorescent lamp ballasts. 429.26 Section 429.26 Energy... COMMERCIAL AND INDUSTRIAL EQUIPMENT Certification § 429.26 Fluorescent lamp ballasts. (a) Sampling plan for selection of units for testing. (1) The requirements of § 429.11 are applicable to fluorescent lamp ballasts...

10 CFR 429.26 - Fluorescent lamp ballasts.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 10 Energy 3 2013-01-01 2013-01-01 false Fluorescent lamp ballasts. 429.26 Section 429.26 Energy... COMMERCIAL AND INDUSTRIAL EQUIPMENT Certification § 429.26 Fluorescent lamp ballasts. (a) Sampling plan for selection of units for testing. (1) The requirements of § 429.11 are applicable to fluorescent lamp ballasts...

14 CFR 31.51 - Ballast.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 1 2013-01-01 2013-01-01 false Ballast. 31.51 Section 31.51 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT AIRWORTHINESS STANDARDS: MANNED FREE BALLOONS Design Construction § 31.51 Ballast. Each captive gas balloon must have a...

14 CFR 31.51 - Ballast.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 1 2012-01-01 2012-01-01 false Ballast. 31.51 Section 31.51 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT AIRWORTHINESS STANDARDS: MANNED FREE BALLOONS Design Construction § 31.51 Ballast. Each captive gas balloon must have a...

14 CFR 31.51 - Ballast.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 1 2014-01-01 2014-01-01 false Ballast. 31.51 Section 31.51 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT AIRWORTHINESS STANDARDS: MANNED FREE BALLOONS Design Construction § 31.51 Ballast. Each captive gas balloon must have a...

Real-time PCR and NASBA for rapid and sensitive detection of Vibrio cholerae in ballast water.

PubMed

Fykse, Else M; Nilsen, Trine; Nielsen, Agnete Dessen; Tryland, Ingun; Delacroix, Stephanie; Blatny, Janet M

2012-02-01

Transport of ballast water is one major factor in the transmission of aquatic organisms, including pathogenic bacteria. The IMO-guidelines of the Convention for the Control and Management of Ships' Ballast Water and Sediments, states that ships are to discharge <1 CFU per 100 ml ballast water of toxigenic Vibrio cholerae, emphasizing the need to establish test methods. To our knowledge, there are no methods sensitive and rapid enough available for cholera surveillance of ballast water. In this study real-time PCR and NASBA methods have been evaluated to specifically detect 1 CFU/100ml of V. cholerae in ballast water. Ballast water samples spiked with V. cholerae cells were filtered and enriched in alkaline peptone water before PCR or NASBA detection. The entire method, including sample preparation and analysis was performed within 7 h, and has the potential to be used for analysis of ballast water for inspection and enforcement control. Copyright © 2011 Elsevier Ltd. All rights reserved.

Ballast water treatment systems: design, regulations, and selection under the choice varying priorities.

PubMed

Satir, Tanzer

2014-09-01

This paper investigates the role of ballast water treatment systems (BWTSs) and proposes a selection procedure for conventional merchant ships based on the financial, legal, and operational circumstances. Through the metallurgical revolution of the nineteenth century, commercial ships are converted to steel hull from wooden structures. By this innovative shift, use of ballast water became an essential part of ships for improving propulsion and stability while reducing stress on hull (instead of rocks). However, the content of ballast water is emerged since it relocates marine species from an ecological composition (usually cargo discharging port) to another one (loading port). Uncontrolled relocation of marine species may cause severe damage to existing ecological basis on ballast discharging area. BWTSs are developed for ships to eliminate marine species (i.e., aquatic invasive species) content by using a filtering device. It ensures an eco-friendly ballasting and de-ballasting process. The selection of proper BWTS is another debate since the BWTSs are designed with cost-quality and cost (eco)-performance variations. The proposed approach denoted that both tonnage and the age of ship are indicative factors on selection. The cost of installation varies based on installation space and active vs. project vessel cases.

Performance of geogrid reinforced ballast under dynamic loading.

DOT National Transportation Integrated Search

2012-07-01

Railroad ballast consists of open graded crushed stone used as a bed for railroad track to provide stability. Over time, : ballast degrades and loses its strength. Fouling of ballast with fines has been a major issue of railway engineering. In this :...

Ten years of Brazilian ballast water management

NASA Astrophysics Data System (ADS)

Castro, Maria Cecilia Trindade; Hall-Spencer, Jason M.; Poggian, Cecília Fonseca; Fileman, Timothy W.

2018-03-01

In 2005, Brazil addressed the environmental challenges posed by ballast water through a unilateral regulation, called the Maritime Standard N° 20 (NORMAM-20), applied to all shipping in her waters. This world-leading decision was the culmination of a process that started during the 1990‧s. Here, we summarize how these ballast water regulations were brought in and adopted and present the findings of 10 years of enforcement (2005-2015) in 39 ports along the Brazilian coast. We show that compliance with the Brazilian standard has increased significantly since the regulations were implemented (p < 0.001). After five years of implementation, non-compliance decreased probably reflecting an increase in awareness of the Brazilian Standard and a shift in the shipping industry commitment to minimize and control the spread of invasive species through ballast water. The Brazilian experience shows that very high levels (97%) of compliance with ballast water management regulations can be made to work in a region of global importance to the maritime industry. In the last decade, the rules governing ballast water in Brazil have evolved to address the demands from the maritime community and to provide updates such as imminent requirements for the use of ballast water management systems on board ships. These regulations are rarely cited when ballast water regulations are discussed internationally, yet there is much to learn from the proactive approach taken by Brazil such as what is feasible and enforceable.

NBIC: National Ballast Information Clearinghouse -- Overview

Science.gov Websites

and ballasting practices as they relate to coastal marine invasions (see Box 1). Established at SERC to the U.S. Coast Guard on the patterns of ballast water delivery by coastal state, vessel type, and

33 CFR 401.30 - Ballast water and trim.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 33 Navigation and Navigable Waters 3 2010-07-01 2010-07-01 false Ballast water and trim. 401.30... OF TRANSPORTATION SEAWAY REGULATIONS AND RULES Regulations Seaway Navigation § 401.30 Ballast water... exclusive economic zone must agree to comply with the “Code of Best Practices for Ballast Water Management...

33 CFR 401.30 - Ballast water and trim.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 33 Navigation and Navigable Waters 3 2011-07-01 2011-07-01 false Ballast water and trim. 401.30... OF TRANSPORTATION SEAWAY REGULATIONS AND RULES Regulations Seaway Navigation § 401.30 Ballast water... exclusive economic zone must agree to comply with the “Code of Best Practices for Ballast Water Management...

33 CFR 401.30 - Ballast water and trim.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 33 Navigation and Navigable Waters 3 2014-07-01 2014-07-01 false Ballast water and trim. 401.30... OF TRANSPORTATION SEAWAY REGULATIONS AND RULES Regulations Seaway Navigation § 401.30 Ballast water... exclusive economic zone must agree to comply with the “Code of Best Practices for Ballast Water Management...

ballast water « Coast Guard Maritime Commons

Science.gov Websites

updates to Marine Safety Center's ballast water management system website The Marine Safety Center recently updated two tools posted to its ballast water management system website to assist industry when completing the ballast water management system type approval process, or when accessing letters of intent. 12

Chamber study of PCB emissions from caulking materials and light ballasts.

PubMed

Liu, Xiaoyu; Guo, Zhishi; Krebs, Kenneth A; Stinson, Rayford A; Nardin, Joshua A; Pope, Robert H; Roache, Nancy F

2015-10-01

The emissions of polychlorinated biphenyl (PCB) congeners from thirteen caulk samples were tested in a micro-chamber system. Twelve samples were from PCB-contaminated buildings and one was prepared in the laboratory. Nineteen light ballasts collected from buildings that represent 13 different models from five manufacturers were tested in 53-L environmental chambers. The rates of PCB congener emissions from caulking materials and light ballasts were determined. Several factors that may have affected the emission rates were evaluated. The experimentally determined emission factors showed that, for a given PCB congener, there is a linear correlation between the emission factor and the concentration of the PCB congener in the source. Furthermore, the test results showed that an excellent log-linear correlation exists between the normalized emission factor and the vapor pressure (coefficient of determination, r(2)⩾0.8846). The PCB congener emissions from ballasts at or near room temperature were relatively low with or without electrical load. However, the PCB congener emission rates increased significantly as the temperature increased. The results of this research provide new data and models for ranking the primary sources of PCBs and supports the development and refinement of exposure assessment models for PCBs. Published by Elsevier Ltd.

Approaches to setting organism-based ballast water discharge standards

EPA Science Inventory

As a major vector by which foreign species invade coastal and freshwater waterbodies, ballast water discharge from ships is recognized as a major environmental threat. The International Maritime Organization (IMO) drafted an international ballast water treaty establishing ballast...

78 FR 33774 - Ballast Water Management Reporting and Recordkeeping

Federal Register 2010, 2011, 2012, 2013, 2014

2013-06-05

...-AB68 Ballast Water Management Reporting and Recordkeeping AGENCY: Coast Guard, DHS. ACTION: Notice of proposed rulemaking. SUMMARY: The Coast Guard proposes to amend its existing ballast water management (BWM... annual report of their BWM practices. The Coast Guard also proposes to update the current ballast water...

33 CFR 151.2040 - What are the mandatory ballast water management requirements for vessels equipped with ballast...

Code of Federal Regulations, 2011 CFR

2011-07-01

... CARRYING OIL, NOXIOUS LIQUID SUBSTANCES, GARBAGE, MUNICIPAL OR COMMERCIAL WASTE, AND BALLAST WATER Ballast Water Management for Control of Nonindigenous Species in Waters of the United States § 151.2040 What are... waters of the United States under the Federal Water Pollution Control Act (33 U.S.C. 1251 to 1376). [USCG...

33 CFR 151.1514 - Ballast water management alternatives under extraordinary conditions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... failure, or other extraordinary conditions, is unable to effect a ballast water exchange before entering... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Ballast water management... SUBSTANCES, GARBAGE, MUNICIPAL OR COMMERCIAL WASTE, AND BALLAST WATER Ballast Water Management for Control of...

33 CFR 151.1514 - Ballast water management alternatives under extraordinary conditions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... failure, or other extraordinary conditions, is unable to effect a ballast water exchange before entering... 33 Navigation and Navigable Waters 2 2011-07-01 2011-07-01 false Ballast water management... SUBSTANCES, GARBAGE, MUNICIPAL OR COMMERCIAL WASTE, AND BALLAST WATER Ballast Water Management for Control of...

33 CFR 151.1515 - Ballast water management alternatives under extraordinary conditions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 33 Navigation and Navigable Waters 2 2012-07-01 2012-07-01 false Ballast water management... SUBSTANCES, GARBAGE, MUNICIPAL OR COMMERCIAL WASTE, AND BALLAST WATER Ballast Water Management for Control of Nonindigenous Species in the Great Lakes and Hudson River § 151.1515 Ballast water management alternatives under...

33 CFR 151.1515 - Ballast water management alternatives under extraordinary conditions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 33 Navigation and Navigable Waters 2 2013-07-01 2013-07-01 false Ballast water management... SUBSTANCES, GARBAGE, MUNICIPAL OR COMMERCIAL WASTE, AND BALLAST WATER Ballast Water Management for Control of Nonindigenous Species in the Great Lakes and Hudson River § 151.1515 Ballast water management alternatives under...

33 CFR 151.1515 - Ballast water management alternatives under extraordinary conditions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 33 Navigation and Navigable Waters 2 2014-07-01 2014-07-01 false Ballast water management... SUBSTANCES, GARBAGE, MUNICIPAL OR COMMERCIAL WASTE, AND BALLAST WATER Ballast Water Management for Control of Nonindigenous Species in the Great Lakes and Hudson River § 151.1515 Ballast water management alternatives under...

Statistical considerations in estimating organism concentrations in ballast water discharges

EPA Science Inventory

Sampling probabilities may affect the practical use of different ballast water performance standards which establish the acceptable concentration of organisms in ballast discharges. The International Maritime Organization (IMO) has initiated a ballast water standard of <10 viabl...

Application of a hydroxyl-radical-based disinfection system for ballast water.

PubMed

Bai, Mindong; Tian, Yiping; Yu, Yixuan; Zheng, Qilin; Zhang, Xiaofang; Zheng, Wu; Zhang, Zhitao

2018-06-02

A hydroxyl radical (OH) ballast water treatment system (BWTS) was developed and applied to inactivate entrained organisms in a 10,000-ton oceanic ship, where OH was produced by a strong ionization discharge combined with a water jet cavitation effect. The calculated OH generation rate was 1373.4 μM min -1 in ballast water, which is much higher than that in other advanced oxidative processes such as photocatalysis. As a result, non-indigenous red tide algae were inactivated to meet the ballast water discharge standards (<10 cells mL -1 ) of the International Maritime Organization. The ratio of variable fluorescence to maximum fluorescence (F v /F m ) for algal chlorophyll rapidly decreased to zero within a contact time of only 6 s, indicating complete inactivation of algae. Observation under a scanning electron microscope showed no cellular materials were released by algal cells upon OH inactivation. A risk assessment of the OH treatment system was conducted, and the ratios of predicted environmental concentrations to predicted no effect concentrations of all detected disinfection byproducts were less than 1, even at a worst-case oxidant concentration of 2.41 mg L -1 . Ship ballast water treated using OH inactivation is safe for marine environments. Finally, the energy consumption and operational costs of the OH BWTS were found to be 0.033 kWh m -3 and CNY 0.03 m -3 , respectively. Copyright © 2018 Elsevier Ltd. All rights reserved.

33 CFR Appendix to Subpart D of... - Ballast Water Reporting Form and Instructions for Ballast Water Reporting Form

Code of Federal Regulations, 2011 CFR

2011-07-01

... 33 Navigation and Navigable Waters 2 2011-07-01 2011-07-01 false Ballast Water Reporting Form and Instructions for Ballast Water Reporting Form Appendix to Subpart D of Part 151 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) POLLUTION VESSELS CARRYING OIL, NOXIOUS LIQUID SUBSTANCES, GARBAGE, MUNICIPAL OR...

Permeability, resistivity and strength of fouled railroad ballast.

DOT National Transportation Integrated Search

2014-04-01

Ballaste : d tracks are the most common tracks used in the railroad industry and are designed to provide a stable, safe, and efficient r : ail foundation. A : ballasted track consists of superstructure (ties, fasteners, and rails), and substructure (...

Mechanics of Ballast Compaction. Volume 5 : Summary Report.

DOT National Transportation Integrated Search

1982-03-01

This report summarizes the results of research on the mechanics of ballast compaction. Details are provided in four preceeding reports. The scope of this summary includes: (1) a description of ballast physical state, (2) methods developed for measuri...

Difficulties in Interpreting Ballast Degradation Level Estimates from Synthetic Ground-Penetrating Radar Data

NASA Astrophysics Data System (ADS)

Scanlan, K. M.; Hendry, M. T.; Martin, C. D.; Schmitt, D. R.

2016-12-01

As fine-grained particles accumulate within railway ballast, it becomes more susceptible to differential deformations, which leads to the loss of proper track alignment and an increased risk for car derailment. Methods for estimating the ballast degradation level from low-frequency (<1 GHz) ground-penetrating radar (GPR) measurements exist, but their applicability in a wide range of track foundation conditions has yet to be evaluated. This analysis, based on simulated GPR data, evaluates the sensitivity of these methods to changing ballast moisture contents, ballast thicknesses and subballast material types. The results highlight that small changes to the track foundation, indepedent of the concentration of degraded ballast, significantly alter the attenuation and reflectivity characteristics of the simualted GPR measurements. As such, ballast degraded to a certain level will manifest with different attenuation and reflectivity characteristics, limiting the ability to accurately and reliably detect these changes using GPR. Radar propagation velocities within the ballast are less influenced by changes in ballast depth and subballast material type. However, ambiguous propagation velocities are observed for certain ballast moisture contents and degradation levels; furthermore, velocities can only be calculated when the ballast thickness is known. These results suggest that while under certain circumstances, with additional information on the track foundation conditons, ballast degradation levels can be estimated from GPR data; in general, the complicated nature of GPR signals makes the quantificaion of ballast degradation levels difficult.

Performance Tests of Alternative Ballast Water Treatment Systems

DOT National Transportation Integrated Search

2001-08-01

This report summarizes the results of the U.S. Coast Guard (USCG) assessment of ballast water treatment system alternatives to ballast water exchange as a means of reducing the probability of aquatice nuisance species (ANS) transfer. The audits inclu...

Examination of an indicative tool for rapidly estimating viable organism abundance in ballast water

NASA Astrophysics Data System (ADS)

Vanden Byllaardt, Julie; Adams, Jennifer K.; Casas-Monroy, Oscar; Bailey, Sarah A.

2018-03-01

Regulatory discharge standards stipulating a maximum allowable number of viable organisms in ballast water have led to a need for rapid, easy and accurate compliance assessment tools and protocols. Some potential tools presume that organisms present in ballast water samples display the same characteristics of life as the native community (e.g. rates of fluorescence). This presumption may not prove true, particularly when ships' ballast tanks present a harsh environment and long transit times, negatively impacting organism health. Here, we test the accuracy of a handheld pulse amplitude modulated (PAM) fluorometer, the Hach BW680, for detecting photosynthetic protists at concentrations above or below the discharge standard (< 10 cells·ml- 1) in comparison to microscopic counts using fluorescein diacetate as a viability probe. Testing was conducted on serial dilutions of freshwater harbour samples in the lab and in situ untreated ballast water samples originating from marine, freshwater and brackish sources utilizing three preprocessing techniques to target organisms in the size range of ≥ 10 and < 50 μm. The BW680 numeric estimates were in agreement with microscopic counts when analyzing freshly collected harbour water at all but the lowest concentrations (< 38 cells·ml- 1). Chi-square tests determined that error is not independent of preprocessing methods: using the filtrate method or unfiltered water, in addition to refining the conversion factor of raw fluorescence to cell size, can decrease the grey area where exceedance of the discharge standard cannot be measured with certainty (at least for the studied populations). When examining in situ ballast water, the BW680 detected significantly fewer viable organisms than microscopy, possibly due to factors such as organism size or ballast water age. Assuming both the BW680 and microscopy with FDA stain were measuring fluorescence and enzymatic activity/membrane integrity correctly, the observed discrepancy

Environmental and economic factors can increase the risk of exotic species introductions to the Arctic region through increased ballast water discharge.

PubMed

Niimi, Arthur J

2004-05-01

The effects of global warming can increase the risk of exotic species introductions in eastern Canadian Arctic waters by reducing surface ice cover and allow increased access to commercial vessels. Ballast water discharged by incoming overseas vessels is an important means for introducing species on a global scale. Analyses of air temperatures at Churchill, Manitoba between 1943 and 2002 indicated an increase in mean temperature within the past decade. Churchill is the only major northern port in this region where grain has been exported on a limited basis due to the short navigation season. Economic analyses of grain exported from Canadian and U.S. ports indicated some cost advantages for using northern ports. The Hudson Bay region is vulnerable to increased exotic species introductions because of its southerly location. Current ballast water exchange measures to reduce the risk of introductions may not be effective because most vessels enter the region with ballast, and the ballast exchange zone is located relatively close to coastal areas where the habitat could be favorable for an introduced species to become established. The probability of a large crab species introduced to this region from northern European waters is discussed. The risk of ballast water-related exotic species introduction to this region may be reduced by expanding the types of cargo handled and developing a strong import market. This approach would accommodate an increase in the number of vessels with cargo, and substantially reduce the volume of ballast carried to this region.

The challenges and promises of genetic approaches for ballast water management

NASA Astrophysics Data System (ADS)

Rey, Anaïs; Basurko, Oihane C.; Rodríguez-Ezpeleta, Naiara

2018-03-01

Ballast water is a main vector of introduction of Harmful Aquatic Organisms and Pathogens, which includes Non-Indigenous Species. Numerous and diversified organisms are transferred daily from a donor to a recipient port. Developed to prevent these introduction events, the International Convention for the Control and Management of Ships' Ballast Water and Sediments will enter into force in 2017. This international convention is asking for the monitoring of Harmful Aquatic Organisms and Pathogens. In this review, we highlight the urgent need to develop cost-effective methods to: (1) perform the biological analyses required by the convention; and (2) assess the effectiveness of two main ballast water management strategies, i.e. the ballast water exchange and the use of ballast water treatment systems. We have compiled the biological analyses required by the convention, and performed a comprehensive evaluation of the potential and challenges of the use of genetic tools in this context. Following an overview of the studies applying genetic tools to ballast water related research, we present metabarcoding as a relevant approach for early detection of Harmful Aquatic Organisms and Pathogens in general and for ballast water monitoring and port risk assessment in particular. Nonetheless, before implementation of genetic tools in the context of the ballast water management convention, benchmarked tests against traditional methods should be performed, and standard, reproducible and easy to apply protocols should be developed.

33 CFR 157.33 - Water ballast in fuel oil tanks.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Water ballast in fuel oil tanks... OIL IN BULK Vessel Operation § 157.33 Water ballast in fuel oil tanks. A new vessel may not carry ballast water in a fuel oil tank. [CGD 74-32, 40 FR 48283, Oct. 14, 1975, as amended by USCG-2000-7641, 66...

[Verification of ballast water exchange for international ships anchored in Xiamen Port by CDOM tracer].

PubMed

Li, Chao; Zhang, Yan-po; Guo, Wei-dong; Zhu, Yue; Xu, Jing; Deng, Xun

2010-09-01

Fluorescence excitation-emission matrix (EEM) and absorption spectroscopy were applied to study the optical properties of 29 CDOM samples collected from different ballast tanks of nine international route vessels anchored in Xiamen Port between October 2007 and April 2008. The purpose was to examine the feasibility of these spectral properties as a tracer to verify if these vessels follow the mid-ocean ballast water exchange (BWE) regulation. Using parallel factor analysis, four fluorescent components were identified, including two humic-like components (C1: 245, 300/386 nm; C2: 250, 345/458 nm) and two protein-like components (C3: 220, 275/306 nm; C4: 235, 290/345 nm), of which C2 component was the suitable fluorescence verification indicator. The vertical distribution of all fluorescent components in ballast tank was nearly similar indicating that profile-mixing sampling was preferable. Combined use of C2 component, spectral slope ratio (SR) of absorption spectroscopy and salinity may provide reasonable verification if BWE carried out by these nine ships. The results suggested that the combined use of multiple parameters (fluorescence, absorption and salinity) would be much reliable to determine the origin of ballast water, and to provide the technical guarantee for fast examination of ballast water exchange in Chinese ports.

Microbial dynamics in acetate-enriched ballast water at different temperatures.

PubMed

Stehouwer, Peter Paul; van Slooten, Cees; Peperzak, Louis

2013-10-01

The spread of invasive species through ships' ballast water is considered as a major ecological threat to the world's oceans. For that reason, the International Maritime Organization (IMO) has set performance standards for ballast water discharge. Ballast water treatment systems have been developed that employ either UV-radiation or 'active substances' to reduce the concentration of living cells to below the IMOs standards. One such active substance is a chemical mixture known as Peraclean(®) Ocean. The residual of Peraclean(®) Ocean is acetate that might be present at high concentrations in discharged ballast water. In cold coastal waters the breakdown of acetate might be slow, causing a buildup of acetate concentrations in the water if regularly discharged by ships. To study the potential environmental impact, microbial dynamics and acetate degradation were measured in discharge water from a Peraclean(®) Ocean treatment system in illuminated microcosms. In addition, microbial dynamics and acetate degradation were studied at -1, 4, 10, 15 and 25°C in dark microcosms that simulated enclosed ballast water tanks. Acetate breakdown indeed occurred faster at higher temperatures. At 25°C the highest bacteria growth, fastest nutrient and oxygen consumption and highest DOC reduction occurred. On the other hand, at -1°C bacterial growth was strongly delayed, only starting to increase after 12 days. Furthermore, at 25°C the acetate pool was not depleted, probably due to nutrient and oxygen limitation. This means that not all acetate will be broken down in ballast water tanks, even during long voyages in warm waters. In addition, at low temperatures acetate breakdown in ballast water tanks and in discharged water will be extremely slow. Therefore, regular discharge of acetate enriched ballast water in harbors and bays may cause eutrophication and changes in the microbial community, especially in colder regions. Copyright © 2013 Elsevier Inc. All rights reserved.

33 CFR 151.2025 - Ballast water management requirements.

Code of Federal Regulations, 2013 CFR

2013-07-01

... COMMERCIAL WASTE, AND BALLAST WATER Ballast Water Management for Control of Nonindigenous Species in Waters... the vessel prior to the date that the vessel is required to comply with the BWDS in accordance with... of the vessel subject to this subpart may employ the AMS for no longer than 5 years from the date...

33 CFR 151.2025 - Ballast water management requirements.

Code of Federal Regulations, 2014 CFR

2014-07-01

... COMMERCIAL WASTE, AND BALLAST WATER Ballast Water Management for Control of Nonindigenous Species in Waters... the vessel prior to the date that the vessel is required to comply with the BWDS in accordance with... of the vessel subject to this subpart may employ the AMS for no longer than 5 years from the date...

33 CFR 151.2025 - Ballast water management requirements.

Code of Federal Regulations, 2012 CFR

2012-07-01

... COMMERCIAL WASTE, AND BALLAST WATER Ballast Water Management for Control of Nonindigenous Species in Waters... the vessel prior to the date that the vessel is required to comply with the BWDS in accordance with... of the vessel subject to this subpart may employ the AMS for no longer than 5 years from the date...

Ballast water regulations and the move toward concentration-based numeric discharge limits.

PubMed

Albert, Ryan J; Lishman, John M; Saxena, Juhi R

2013-03-01

Ballast water from shipping is a principal source for the introduction of nonindigenous species. As a result, numerous government bodies have adopted various ballast water management practices and discharge standards to slow or eliminate the future introduction and dispersal of these nonindigenous species. For researchers studying ballast water issues, understanding the regulatory framework is helpful to define the scope of research needed by policy makers to develop effective regulations. However, for most scientists, this information is difficult to obtain because it is outside the standard scientific literature and often difficult to interpret. This paper provides a brief review of the regulatory framework directed toward scientists studying ballast water and aquatic invasive species issues. We describe different approaches to ballast water management in international, U.S. federal and state, and domestic ballast water regulation. Specifically, we discuss standards established by the International Maritime Organization (IMO), the U.S. Coast Guard and U.S. Environmental Protection Agency, and individual states in the United States including California, New York, and Minnesota. Additionally, outside the United States, countries such as Australia, Canada, and New Zealand have well-established domestic ballast water regulatory regimes. Different approaches to regulation have recently resulted in variations between numeric concentration-based ballast water discharge limits, particularly in the United States, as well as reliance on use of ballast water exchange pending development and adoption of rigorous science-based discharge standards. To date, numeric concentration-based discharge limits have not generally been based upon a thorough application of risk-assessment methodologies. Regulators, making decisions based on the available information and methodologies before them, have consequently established varying standards, or not established standards at all. The

33 CFR 151.2030 - Ballast water discharge standard (BWDS).

Code of Federal Regulations, 2012 CFR

2012-07-01

... possibly prevent the introduction and spread of non-indigenous aquatic invasive species. ... COMMERCIAL WASTE, AND BALLAST WATER Ballast Water Management for Control of Nonindigenous Species in Waters... maximum extent practicable that aquatic nuisance species are not discharged into waters of the United...

33 CFR 151.2030 - Ballast water discharge standard (BWDS).

Code of Federal Regulations, 2013 CFR

2013-07-01

... possibly prevent the introduction and spread of non-indigenous aquatic invasive species. ... COMMERCIAL WASTE, AND BALLAST WATER Ballast Water Management for Control of Nonindigenous Species in Waters... maximum extent practicable that aquatic nuisance species are not discharged into waters of the United...

33 CFR 151.2030 - Ballast water discharge standard (BWDS).

Code of Federal Regulations, 2014 CFR

2014-07-01

... possibly prevent the introduction and spread of non-indigenous aquatic invasive species. ... COMMERCIAL WASTE, AND BALLAST WATER Ballast Water Management for Control of Nonindigenous Species in Waters... maximum extent practicable that aquatic nuisance species are not discharged into waters of the United...

Compact Fluorescent Plug-In Ballast-in-a-Socket

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rebecca Voelker

2001-12-21

The primary goal of this program was to develop a ballast system for plug-in CFLs (compact fluorescent lamps) that will directly replace standard metal shell, medium base incandescent lampholders (such as Levition No. 6098) for use with portable lamp fixtures, such as floor, table and desk lamps. A secondary goal was to identify a plug-in CFL that is optimized for use with this ballast. This Plug-in CFL Ballastin-a-Socket system will allow fixture manufacturers to easily manufacture CFL-based high-efficacy portable fixtures that provide residential and commercial consumers with attractive, cost-effective, and energy-efficient fixtures for use wherever portable incandescent fixtures are usedmore » today. The advantages of this proposed system over existing CFL solutions are that the fixtures can only be used with high-efficacy CFLs, and they will be more attractive and will have lower life-cycle costs than screw-in or adapter-based CFL retrofit solutions. These features should greatly increase the penetration of CFL's into the North American market. Our work has shown that using integrated circuits it is quite feasible to produce a lamp-fixture ballast of a size comparable to the current Edison-screw 3-way incandescent fixtures. As for price points for BIAS-based fixtures, end-users polled by the Lighting Research Institute at RPI indicated that they would pay as much as an additional $10 for a lamp containing such a ballast. The ballast has been optimized to run with a 26 W amalgam triple biax lamp in the base-down position, yet can accept non-amalgam versions of the lamp. With a few part alterations, the ballast can be produced to support 32 W lamps as well. The ballast uses GE's existing L-Comp[1] power topology in the circuit so that the integrated circuit design would be a design that could possibly be used by other CFL and EFL products with minor modifications. This gives added value by reducing cost and size of not only the BIAS, but also possibly other

Feasibility of potable water generators to meet vessel numeric ballast water discharge limits.

PubMed

Albert, Ryan J; Viveiros, Edward; Falatko, Debra S; Tamburri, Mario N

2017-07-15

Ballast water is taken on-board vessels into ballast water tanks to maintain vessel draft, buoyancy, and stability. Unmanaged ballast water contains aquatic organisms that, when transported and discharged to non-native waters, may establish as invasive species. Technologies capable of achieving regulatory limits designed to decrease the likelihood of invasion include onboard ballast water management systems. However, to date, the treatment development and manufacturing marketplace is limited to large vessels with substantial ballast requirements. For smaller vessels or vessels with reduced ballast requirements, we evaluated the feasibility of meeting the discharge limits by generating ballast water using onboard potable water generators. Case studies and parametric analyses demonstrated the architectural feasibility of installing potable water generators onboard actual vessels with minimal impacts for most vessel types evaluated. Furthermore, land-based testing of a potable water generator demonstrated capability to meet current numeric discharge limits for living organisms in all size classes. Published by Elsevier Ltd.

Ship board testing of a deoxygenation ballast water treatment.

PubMed

McCollin, Tracy; Quilez-Badia, Gemma; Josefsen, Kjell D; Gill, Margaret E; Mesbahi, Ehsan; Frid, Chris L J

2007-08-01

A ship board trial of a deoxygenation method for treating ballast water was carried out during a voyage from Southampton (United Kingdom) to Manzanillo (Panama). A nutrient solution added to two ballast tanks encouraged bacterial growth, resulting in a gradual change to an anoxic environment. Samples were taken from two treated tanks and two untreated tanks to assess changes in the abundance and viability of zooplankton, phytoplankton and bacteria. The work was carried out before the International Maritime Organization (IMO) standard was agreed so only a broad indication of whether the results achieved the standard was given. For the zooplankton, the standard would have been achieved within 5 or 7 days but the phytoplankton results were inconclusive. The biological efficacy was the result of the combination of several factors, including the treatment, pump damage and an increase in the water temperature during the voyage.

The estimation for ballast water discharged to China from 2007 to 2014.

PubMed

Zhang, Xiaofang; Bai, Mindong; Tian, Yiping; Du, Huan; Zhang, Zhitao

2017-11-15

Ballast water has been identified as one of the main causes for worldwide transfer of non-indigenous marine species. The volume and source of ballast water are the fundamental elements for an evaluation of the risk posed. However, it is difficult to obtain the volume of ballast water discharged to China, because of the absence of information platform, and until now there is no public report. In this paper, the total volume of ballast water discharged to China and Chinese five major port-groups were estimated. Results showed: the total volume of ballast water exhibited a trend of slow increase from 2007 to 2014, and reached 311 million tons in 2014. Yangtze River Delta received the highest volume of ballast water among all port-groups. The information provided in this research may play an important role in helping policy decision-makers manage such coastal discharges. Copyright © 2017 Elsevier Ltd. All rights reserved.

33 CFR 151.1511 - Ballast water discharge standard (BWDS).

Code of Federal Regulations, 2014 CFR

2014-07-01

... COMMERCIAL WASTE, AND BALLAST WATER Ballast Water Management for Control of Nonindigenous Species in the... maximum extent practicable that aquatic nuisance species are not discharged into waters of the United..., practicable, and/or may possibly prevent the introduction and spread of non-indigenous aquatic invasive...

33 CFR 151.1511 - Ballast water discharge standard (BWDS).

Code of Federal Regulations, 2012 CFR

2012-07-01

... COMMERCIAL WASTE, AND BALLAST WATER Ballast Water Management for Control of Nonindigenous Species in the... maximum extent practicable that aquatic nuisance species are not discharged into waters of the United..., practicable, and/or may possibly prevent the introduction and spread of non-indigenous aquatic invasive...

33 CFR 151.1511 - Ballast water discharge standard (BWDS).

Code of Federal Regulations, 2013 CFR

2013-07-01

... COMMERCIAL WASTE, AND BALLAST WATER Ballast Water Management for Control of Nonindigenous Species in the... maximum extent practicable that aquatic nuisance species are not discharged into waters of the United..., practicable, and/or may possibly prevent the introduction and spread of non-indigenous aquatic invasive...

Brine-induced mortality of non-indigenous invertebrates in residual ballast water.

PubMed

Bradie, Johanna N; Bailey, Sarah A; van der Velde, Gerard; Macisaac, Hugh J

2010-12-01

All transoceanic vessels entering the Great Lakes are required to manage ballast water and ballast tank residuals with ballast water exchange and tank flushing, respectively. While these management procedures effectively reduce the density and richness of biota in ballast waters and thereby reduce the risk of transferring non-indigenous species, some ships are unable to uniformly manage all tanks. Laboratory experiments were conducted to evaluate sodium chloride brine as an emergency treatment for ballast tanks with non-compliant residuals. Invertebrate communities collected from i) Detroit River, ii) exchanged ballast tanks arriving in the Great Lakes, and iii) North Sea ports, were exposed to a range of brine concentrations (15-115‰) until complete mortality was reached. Results indicate that a 1-h exposure to 115‰ brine is a broadly effective treatment (>99.9% mortality) regardless of treatment temperature, taxonomic group, or species' source habitat salinity. A median of 0.00% (range 0.00-5.33) of individuals are expected to survive treatment and the expected number of viable individuals released after treatment is within Canadian and proposed international discharge standards. Before implementation, validation with ship-scale trials is recommended. Copyright © 2010 Elsevier Ltd. All rights reserved.

Ballast Water Discharges into the Great Lakes from Overseas Vessels

EPA Pesticide Factsheets

Analysis of Ballast Water Discharges into the Great Lakes from Overseas Vessels from 2010 to 2013 - An assessment of the volume, location, and global port origins of ballast water discharges in the Great Lakes (May 2015).

Estimating Deterioration in the Concrete Tie-Ballast Interface Based on Vertical Tie Deflection Profile: A Numerical Study

DOT National Transportation Integrated Search

2016-04-12

In ballasted concrete tie track, the tie-ballast interface can : deteriorate resulting in concrete tie bottom abrasion, ballast : pulverization and/or voids in tie-ballast interfaces. Tie-ballast : voids toward tie ends can lead to unfavorable center...

Factors influencing densities of non-indigenous species in the ballast water of ships arriving at ports in Puget Sound, Washington, United States

USGS Publications Warehouse

Cordell, J.R.; Lawrence, D.J.; Ferm, N.C.; Tear, L.M.; Smith, S.S.; Herwig, R.P.

2009-01-01

Oceanographic characteristics and the presence of international shipping in Puget Sound, Washington, USA contribute to its vulnerability to non-indigenous species (NIS) invasions. To evaluate NIS arriving in ballast water, zooplankton was sampled in 380 ballast tanks of ships after they entered Puget Sound. Taxa were classified into a higher risk group of coastal organisms (including known NIS), and a lower risk group of largely oceanic species. Most ships reported conducting mid-ocean ballast water exchange (BWE). However, despite state regulations requiring BWE, and apparent compliance by ship operators, most sampled tanks from both transpacific and coastal routes had coastal zooplankton densities exceeding internationally proposed discharge standards. BWE efficiency models and controlled before-and-after BWE experiments indicate that BWE consistently removes most coastal zooplankton. However, this study found that although the empty-refill method of BWE significantly reduced coastal plankton compared with un-exchanged tanks, the flow-through method did not, and in either case remaining coastal plankton densities presented appreciable risks of introducing NIS. Densities of high risk taxa were consistently and significantly higher from US domestic trips dominated by tank ships carrying ballast water from California, and lower in samples from trans-Pacific trips dominated by container ships and bulk carriers with ballast from Asia. These findings are probably a result of the dense and diverse NIS assemblages present in California and other US west coast estuaries and the comparatively short transit times between them and Puget Sound. While it appears that BWE can effectively replace NIS with less risky ocean species, new reporting, verification, and operational procedures may be necessary to enhance BWE efficacy. In the long-term, the introduction of ballast water treatment technologies may be required to significantly reduce the discharge of risky organisms from

Temporal modelling of ballast water discharge and ship-mediated invasion risk to Australia

PubMed Central

Cope, Robert C.; Prowse, Thomas A. A.; Ross, Joshua V.; Wittmann, Talia A.; Cassey, Phillip

2015-01-01

Biological invasions have the potential to cause extensive ecological and economic damage. Maritime trade facilitates biological invasions by transferring species in ballast water, and on ships' hulls. With volumes of maritime trade increasing globally, efforts to prevent these biological invasions are of significant importance. Both the International Maritime Organization and the Australian government have developed policy seeking to reduce the risk of these invasions. In this study, we constructed models for the transfer of ballast water into Australian waters, based on historic ballast survey data. We used these models to hindcast ballast water discharge over all vessels that arrived in Australian waters between 1999 and 2012. We used models for propagule survival to compare the risk of ballast-mediated propagule transport between ecoregions. We found that total annual ballast discharge volume into Australia more than doubled over the study period, with the vast majority of ballast water discharge and propagule pressure associated with bulk carrier traffic. As such, the ecoregions suffering the greatest risk are those associated with the export of mining commodities. As global marine trade continues to increase, effective monitoring and biosecurity policy will remain necessary to combat the risk of future marine invasion events. PMID:26064643

Density matters: Review of approaches to setting organism-based ballast water discharge standards

USGS Publications Warehouse

Lee II,; Frazier,; Ruiz,

2010-01-01

As part of their effort to develop national ballast water discharge standards under NPDES permitting, the Office of Water requested that WED scientists identify and review existing approaches to generating organism-based discharge standards for ballast water. Six potential approaches were identified and the utility and uncertainties of each approach was evaluated. During the process of reviewing the existing approaches, the WED scientists, in conjunction with scientists at the USGS and Smithsonian Institution, developed a new approach (per capita invasion probability or "PCIP") that addresses many of the limitations of the previous methodologies. THE PCIP approach allows risk managers to generate quantitative discharge standards using historical invasion rates, ballast water discharge volumes, and ballast water organism concentrations. The statistical power of sampling ballast water for both the validation of ballast water treatment systems and ship-board compliance monitoring with the existing methods, though it should be possible to obtain sufficient samples during treatment validation. The report will go to a National Academy of Sciences expert panel that will use it in their evaluation of approaches to developing ballast water discharge standards for the Office of Water.

Semi-empirical model for the assessment of railway ballast using GPR

NASA Astrophysics Data System (ADS)

Giulia Brancadoro, Maria; Benedetto, Andrea

2017-04-01

Over time, railways have become a very competitive mean of transportation, especially for long distances. In order to ensure high level of safety, comfort and regularity of transportation, an efficient maintenance of the railway track-bed is crucial. In fact, the cyclic loads passing on the rails produce a progressive deterioration of railway ballast beneath the sleepers, and a breakdown of its particles that causes a general decrease of railway performances. This work aims at proposing a semi-empirical model for the characterisation of railway ballast grading, through the spectral analysis of Ground-Penetrating Radar (GPR) signal. To this effect, a theoretical study has been preliminary conducted to investigate the propagation and scattering phenomena of the electromagnetic waves within a ballast layer. To confirm the theoretical assumptions, high-frequency GPR signals have been both collected in laboratory and virtual environment. Concerning the latter, progressively more complex numerical domains have been designed and subjected to synthetic GPR test, by a Finite Different Time Domain (FTDT) procedure, run in GPR Max 2D simulator. As first simulation steps, ballast aggregates simplified through circles have been accounted for, with increasing values of radius. Subsequently, real-scale scenarios characterized by multi-size ballast particles, consistent with three different grain size distribution from railway network standards, have been reproduced by the employment of Random Sequential Adsorption - RSA algorithm. As far as the laboratory procedures, real GPR tests have been carried out on an experimental framework purposely set up, and composed of a methacrylate tank filled up with limestone-derived railway ballast. The ballast aggregates grading has been retrieved by means of an automatic image analysis algorithm, run on the lateral sight of the transparent tank. Through their spectral analysis, an empirical relationship between the position of the amplitude

Limiting invasive species in ballast water

NASA Astrophysics Data System (ADS)

Showstack, Randy

2011-06-01

Ballast water is often intentionally loaded onto cargo ships and other vessels to provide weight necessary for safe maneuvering. However, this practice can unintentionally transport exotic organisms to parts of the world where populations of these organisms can establish themselves in new habitats as invasive and environmentally and economically disruptive species. Each year, an estimated 196 million metric tons of ballast water are discharged into U.S. coastal waters and the Great Lakes alone from an average of more than 90,000 visits of commercial ships greater than 300 metric tons, according to a 2 June report by the U.S. National Research Council (NRC) of the National Academies.

Mechanics of Ballast Compaction. Volume 3 : Field Test Results for Ballast Physical State Measurement

DOT National Transportation Integrated Search

1982-03-01

The important mechanical processes which influence the ballast physical state in track are tamping, crib and shoulder compaction and train traffic. Three methods of assessing physical state were used at four railroad sites to obtain needed data on th...

Optimization of Ballast Design: A Case Study of the Physics Entrepreneurship Program

NASA Astrophysics Data System (ADS)

Ding, Jun; Cheng, Norman; Lamouri, Abbas; Sulcs, Juris; Brown, Robert; Taylor, Cyrus

2001-10-01

This talk presents a typical internship project for students in the Physics Entrepreneurship Program at Case Western Reserve University. As part of their overall strategy, Advanced Lighting International (ADLT) is involved in the production of magnetic ballasts for metal halide lamps. The systems in which these ballasts function is undergoing rapid evolution, leading to the question of how the design of the ballasts can be optimized in order to deliver superior performance for lower cost. Addressing this question requires a full understanding of a variety of issues ranging from the basic modeling of the physics of the magnetic ballasts to questions of overall market strategy, manufacturing considerations, and the competitive environment.

A unique aspect of ballast water management requirements--the same location concept.

PubMed

Gollasch, Stephan; David, Matej

2012-09-01

Under certain circumstances vessels do not need to meet ballast water management requirements as stated in the International Convention for the Management and Control of Ballast Water and Sediments (BWM Convention). Besides exceptions to ensure e.g., (a) the safety of a ship, (b) discharge of ballast water for the purpose of avoiding or minimizing pollution incidents, (c) uptake and discharge on high seas of the same ballast water, the same location concept comes into play as ballast water discharges from a ship at the same location where it was taken up is also excepted from BWM requirements. The term same location was not defined in this instrument, hence it is exposed to different interpretations (e.g., a terminal, a port, a larger area where two or more ports may be located). As the BWM Convention is an instrument with biological meaning, the authors recommend a biologically meaningful definition of the same location in this contribution. Copyright © 2012 Elsevier Ltd. All rights reserved.

33 CFR 151.2035 - What are the required ballast water management practices for my vessel?

Code of Federal Regulations, 2011 CFR

2011-07-01

... SUBSTANCES, GARBAGE, MUNICIPAL OR COMMERCIAL WASTE, AND BALLAST WATER Ballast Water Management for Control of... ballast water in areas within or that may directly affect marine sanctuaries, marine preserves, marine...

Verifying Ballast Water Treatment Performance

EPA Science Inventory

The U.S. Environmental Protection Agency, NSF International, Battelle, and U.S. Coast Guard are jointly developing a protocol for verifying the technical performance of commercially available technologies designed to treat ship ballast water for potentially invasive species. The...

Ballast water compliance monitoring: A new application for ATP

NASA Astrophysics Data System (ADS)

Lo Curto, A.; Stehouwer, P.; Gianoli, C.; Schneider, G.; Raymond, M.; Bonamin, V.

2018-03-01

The coming into force of the USCG ballast water regulations and the IMO ballast water management convention resulted in the development of several technologies approved for the treatment of ballast water. To ensure compliance of these technologies, the development of rapid and robust analysis methods was necessary. In collaboration with the SGS Group (Switzerland) and LuminUltra (Canada), Aqua-tools (France) has developed an innovative Ballast Water Treatment Monitoring (BWTM) kit for rapid onboard testing. The affordable kit provides results in less than 1 h, is easy to use and durable ensuring that the ballast water treatment system on the ship is fully compliant with the discharge standards upon arrival in port. The core of this method is a combination of high-quality reagents (lysis solution and ATP 2G Luminase™ enzyme) not inhibited by salinity and a patented fast homogenizing method for ATP extraction developed for a higher ATP recovery from zooplankton and phytoplankton. Compared to traditional analysis methods, the BWTM Kit provides fast and accurate results for all three fractions of microorganisms (≥ 50 μm, ≥ 10 ÷ < 50 μm and bacteria). Preliminary tests carried out in cooperation with SGS showed that the proposed method was able to detect onboard the efficiency of the treatment systems used. Compliance limits were established for all size fractions and a correlation between the standard methods (microscopy, plate count, MPN) and ATP was evaluated. The BWTM kit can provide a fast indication of compliance or gross exceedance. The rare borderline cases, when encountered, of course require additional confirmation.

46 CFR 162.060-16 - Changes to an approved ballast water management system (BWMS).

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 6 2013-10-01 2013-10-01 false Changes to an approved ballast water management system...) EQUIPMENT, CONSTRUCTION, AND MATERIALS: SPECIFICATIONS AND APPROVAL ENGINEERING EQUIPMENT Ballast Water Management Systems § 162.060-16 Changes to an approved ballast water management system (BWMS). (a) The...

46 CFR 162.060-16 - Changes to an approved ballast water management system (BWMS).

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 6 2014-10-01 2014-10-01 false Changes to an approved ballast water management system...) EQUIPMENT, CONSTRUCTION, AND MATERIALS: SPECIFICATIONS AND APPROVAL ENGINEERING EQUIPMENT Ballast Water Management Systems § 162.060-16 Changes to an approved ballast water management system (BWMS). (a) The...

Nucleic acids-based tools for ballast water surveillance, monitoring, and research

NASA Astrophysics Data System (ADS)

Darling, John A.; Frederick, Raymond M.

2018-03-01

Understanding the risks of biological invasion posed by ballast water-whether in the context of compliance testing, routine monitoring, or basic research-is fundamentally an exercise in biodiversity assessment, and as such should take advantage of the best tools available for tackling that problem. The past several decades have seen growing application of genetic methods for the study of biodiversity, driven in large part by dramatic technological advances in nucleic acids analysis. Monitoring approaches based on such methods have the potential to increase dramatically sampling throughput for biodiversity assessments, and to improve on the sensitivity, specificity, and taxonomic accuracy of traditional approaches. The application of targeted detection tools (largely focused on PCR but increasingly incorporating novel probe-based methodologies) has led to a paradigm shift in rare species monitoring, and such tools have already been applied for early detection in the context of ballast water surveillance. Rapid improvements in community profiling approaches based on high throughput sequencing (HTS) could similarly impact broader efforts to catalogue biodiversity present in ballast tanks, and could provide novel opportunities to better understand the risks of biotic exchange posed by ballast water transport-and the effectiveness of attempts to mitigate those risks. These various approaches still face considerable challenges to effective implementation, depending on particular management or research needs. Compliance testing, for instance, remains dependent on accurate quantification of viable target organisms; while tools based on RNA detection show promise in this context, the demands of such testing require considerable additional investment in methods development. In general surveillance and research contexts, both targeted and community-based approaches are still limited by various factors: quantification remains a challenge (especially for taxa in larger size

Zero energy-storage ballast for compact fluorescent lamps

DOEpatents

Schultz, William Newell; Thomas, Robert James

1999-01-01

A CFL ballast includes complementary-type switching devices connected in series with their gates connected together at a control node. The switching devices supply a resonant tank circuit which is tuned to a frequency near, but slightly lower than, the resonant frequency of a resonant control circuit. As a result, the tank circuit restarts oscillations immediately following each zero crossing of the bus voltage. Such rapid restarts avoid undesirable flickering while maintaining the operational advantages and high efficacy of the CFL ballast.

Ship traffic and the introduction of diatoms and dinoflagellates via ballast water in the port of Annaba, Algeria

NASA Astrophysics Data System (ADS)

Cheniti, Radhia; Rochon, André; Frihi, Hocine

2018-03-01

We present here the first study on the role of ship traffic in the introduction of potentially harmful and/or non-indigenous species in the port of Annaba (Algeria). A total of 25 ships of two different types (general cargo and bulk carriers) were sampled and separated into two categories: oceanic and Mediterranean ships. We estimated propagule pressure of high-risk coastal phytoplankton delivered in ballast water to the port of Annaba. We identified 40 diatom and 38 dinoflagellate taxa, among which, 11 harmful/toxic taxa: Pseudo-nitzschia spp., Alexandrium tamarense, Alexandrium sp., Dinophysis acuminata, Dinophysis rotundata, Dinophysis sp., Gonyaulax spinifera, Gymnodinium catenatum, Lingulodinium polyedrum, Protoceratium reticulatum and cyst of Alexandrium sp. In addition, 8 taxa (5 diatoms, 1 dinoflagellate and 2 dinoflagellate cysts) never observed in the Annaba region were considered as potentially non-indigenous: Actinoptychus splendens, Coscinodiscus asteromphalus, Coscinodiscus lineatus, Odentella granulata, Thalassiosira cf. decipiens, Prorocentrum scutellum, cyst of Polykrikos kofoidii and Islandinium minutum. Several factors were examined, including ship routes, ballast water age and the volume of ballast water discharged. Our analyses revealed that diatom and dinoflagellate abundances decreased with ballast water age, possibly as a result of mortality of species due to voyage length and lack of light in ballast tanks. Estimates of actual propagule pressure, diatoms and dinoflagellates abundances varied from 1 to 4 × 108 cells/ship. The results of this study could serve as the baseline for the development and implementation of monitoring and ballast water management programs in ports of Algeria.

Ballast Water Self Monitoring

DTIC Science & Technology

2011-11-01

Analytical Methods .........................................................22  7 Estimated Capital Cost for Vessels Needing Additional Ballast Water...streams; narrative water-quality based effluent limits; inspection, monitoring, recordkeeping, and reporting requirements; and additional requirements...decline of several pelagic fish species in the Sacramento-San Joaquin River Delta by reducing the plankton food base of the ecosystem (California State

Zero energy-storage ballast for compact fluorescent lamps

DOEpatents

Schultz, W.N.; Thomas, R.J.

1999-08-31

A CFL ballast includes complementary-type switching devices connected in series with their gates connected together at a control node. The switching devices supply a resonant tank circuit which is tuned to a frequency near, but slightly lower than, the resonant frequency of a resonant control circuit. As a result, the tank circuit restarts oscillations immediately following each zero crossing of the bus voltage. Such rapid restarts avoid undesirable flickering while maintaining the operational advantages and high efficacy of the CFL ballast. 4 figs.

Review of interdisciplinary devices for detecting the quality of ship ballast water.

PubMed

Bakalar, Goran

2014-01-01

The results of the ship ballast water treatment systems neutralization need to be verified in a transparent and trustful way before the ship enters a port. Some researches and results, explained in this article, confirm a need for a good verification. If there is no good methodology agreed, then it would not be accepted the solution that the BWMC (Ballast Water Management Convention) 2004 did protect the sea environment in full meaning. The main problem of ballast neutralization are remaining microorganisms (algae blooms, bacteria) ≥10 and <50. Autonomy of the future ballast water detection device has been explained and newest detection methods analyzed. The ranking analysis has been done thru PROMETHEE II (Preference Ranking Organization Method for Enrichment Evaluations) and results were shown by D-Sight software projections.

The temperature-ballast hypothesis explains carbon export efficiency observations in the Southern Ocean

NASA Astrophysics Data System (ADS)

Britten, Gregory L.; Wakamatsu, Lael; Primeau, François W.

2017-02-01

Carbon export from the Southern Ocean exerts a strong control on the ocean carbon sink, yet recent observations from the region demonstrate poorly understood relationships in which carbon export efficiency is weakly related to temperature. These observations conflict with traditional theory where export efficiency increases in colder waters. A recently proposed "temperature-ballast hypothesis" suggests an explanatory mechanism where the effect of temperature-dependent respiration is masked by variation in particle-ballast as upwelling waters move northward from Antarctica. We use observations and statistical models to test this mechanism and find positive support for the hypothesized temperature-ballast interactions. Best fitting models indicate a significant relation between export efficiency and silica-ballast while simultaneously revealing the expected inverse effect of temperature once ballast is accounted for. These findings reconcile model predictions, metabolic theory, and carbon export observations in the Southern Ocean and have consequences for how the ocean carbon sink responds to climate change.

46 CFR 162.060-14 - Information requirements for the ballast water management system (BWMS) application.

Code of Federal Regulations, 2014 CFR

2014-10-01

... ENGINEERING EQUIPMENT Ballast Water Management Systems § 162.060-14 Information requirements for the ballast... 46 Shipping 6 2014-10-01 2014-10-01 false Information requirements for the ballast water management system (BWMS) application. 162.060-14 Section 162.060-14 Shipping COAST GUARD, DEPARTMENT OF...

46 CFR 162.060-14 - Information requirements for the ballast water management system (BWMS) application.

Code of Federal Regulations, 2013 CFR

2013-10-01

... ENGINEERING EQUIPMENT Ballast Water Management Systems § 162.060-14 Information requirements for the ballast... 46 Shipping 6 2013-10-01 2013-10-01 false Information requirements for the ballast water management system (BWMS) application. 162.060-14 Section 162.060-14 Shipping COAST GUARD, DEPARTMENT OF...

Pollution characteristics and ecological risk of heavy metals in ballast tank sediment.

PubMed

Feng, Daolun; Chen, Xiaofei; Tian, Wen; Qian, Qun; Shen, Hao; Liao, Dexiang; Lv, Baoyi

2017-02-01

This study was conducted to illustrate the contents and potential ecological risk of heavy metals in ballast tank sediment. Ballast sediment samples were collected from six ships during their stay in shipyard, and the heavy metals were determined by inductive coupled plasma emission spectrometer. Results showed that high concentrations of heavy metals were detected in all six sediment samples following the order: Zn > Cu > Pb > Cr > As > Cd > Hg. The geoaccumulation index explained the average pollution degree of heavy metals decreased as the following: Zn > Pb > Cu > As > Cr > Hg, and the environmental risk indices suggested that concentration found of Zn, Pb, and Cu might be highly toxic to aquatic organisms. Principal component and correlation analysis indicated the metal pollution in ballast tank sediment was affected by complex and different contamination mechanisms, and the corrosion of ballast tank played an important role in this process. In conclusion, this study is very useful for comprehensive consideration and efficient management of ballast tank sediment in order to protect the marine environment.

Ballast Blockade: Stopping Aquatic Immigrants.

ERIC Educational Resources Information Center

White, Sara

2003-01-01

Presents students with six ballast water treatment methods to evaluate. Allows students to acquaint themselves with current Great Lakes topics while simultaneously partaking in decision-making processes that could affect them. Emphasizes not only an important environmental issue for the Great Lakes, but also the importance of decision-making…

NBIC: National Ballast Information Clearinghouse

Science.gov Websites

SERC >| Marine Invasions Research Lab NBIC logo National Ballast Information Clearinghouse Smithsonian Environmental Research Center Logo US Coast Guard Logo Submit BW Report | Search NBIC Database | NBIC Research & Development | NBIC News | Home Photos of ships Photos of ships NOTE: 4 March 2018

Effects of temperature on type approval testing of ballast water treatment systems.

PubMed

Drillet, Guillaume; Schmoker, Claire; Trottet, Aurore; Mahjoub, Mohamed-Sofiane; Duchemin, Matthieu; Andersen, Martin

2013-04-01

To limit the risk associated with invasion of habitats by exogenous species, the International Convention for the Control and Management of the Ships' Ballast Water and Sediments was adopted in February 2004 and may soon enter into force. The International Maritime Organization (IMO) has produced guidelines to assess the efficacy and reliability of Ballast Water Treatment Systems (BWTS), but no guidance on how to take temperature into account during test cycles has been provided yet. Temperature is one of the main factors influencing the distribution and ecology of organisms along latitudes. Its increase results in higher grazing, growth, and reproduction rates of zooplankton. Under dark conditions, phytoplankton loss is also increased due to faster natural decay as well as enhanced top down control from zooplankton. Increased temperatures also improve the efficacy of chemical treatment, whereas the decay rates of disinfectants and their byproducts are potentially accelerated. The IMO guidelines for the type approval of BWTS should be amended to include recommendations on how to take temperature into account. Failing to ensure comparability and reliability between tests may pose a threat to the environment and may create problems for those attempting to apply BWTS. We propose to use a fixed Q10 value and a temperature of reference to adjust the retention time in ballast water tanks during testing. Copyright © 2013 SETAC.

33 CFR 151.2045 - What are the mandatory recordkeeping requirements for vessels equipped with ballast tanks that...

Code of Federal Regulations, 2011 CFR

2011-07-01

... OR COMMERCIAL WASTE, AND BALLAST WATER Ballast Water Management for Control of Nonindigenous Species... facility. Include the following: (i) The origin of ballast water. This includes date(s), location(s...

10 CFR Appendix B to Subpart S to... - Certification Report for Metal Halide Lamp Ballasts

Code of Federal Regulations, 2011 CFR

2011-01-01

... 10 Energy 3 2011-01-01 2011-01-01 false Certification Report for Metal Halide Lamp Ballasts B... PROGRAM FOR CERTAIN COMMERCIAL AND INDUSTRIAL EQUIPMENT Metal Halide Lamp Ballasts and Fixtures Pt. 431, Subpt. S, App. B Appendix B to Subpart S to Part 431—Certification Report for Metal Halide Lamp Ballasts...

How to approach ballast water management in European seas

NASA Astrophysics Data System (ADS)

David, Matej; Gollasch, Stephan

2018-02-01

The latest research continues to show that the ballast water issue is very complex, which makes it very challenging to manage. In 2004, the International Convention for the Control and Management of Ships' Ballast Water and Sediments (BWM Convention) was adopted to globally harmonize action against the transfer of harmful aquatic organisms and pathogens via ships' ballast water and related sediments. Analyses of the BWM Convention requirements, conducted through different research projects mainly aiming to provide support for the implementation of the BWM Convention, have shown that there are different steps countries need to take and that there are still some open issues which need to be solved. This paper presents some of the main issues identified and the core theoretical and applied measures required to solve these issues, with the aim to support more efficient and coordinated implementation of the BWM Convention requirements in EU seas. The approaches recommended here for the EU may be universally interesting for similar application in other areas of the world.

Concentrated sodium chloride brine solutions as an additional treatment for preventing the introduction of nonindigenous species in the ballast tanks of ships declaring no ballast on board.

PubMed

Santagata, Scott; Bacela, Karolina; Reid, David F; Mclean, Kevin A; Cohen, Jill S; Cordell, Jeffery R; Brown, Christopher W; Johengen, Thomas H; Ruiz, Gregory M

2009-02-01

Currently, seawater flushing is the only management strategy for reducing the number of viable organisms in residual sediments and water of ballast tanks of vessels declaring no ballast on board (NOBOB) that traffic ports of the eastern United States. Previously, we identified several species of freshwater and brackish-water peracarid crustaceans able to survive the osmotic shock that occurs during open-ocean ballast water exchange and, potentially, to disperse over long distances via ballasted ships and NOBOB vessels. We tested the efficacy of concentrated sodium chloride brine solutions as an additional treatment for eradicating the halotolerant taxa often present in the ballast tanks of NOBOB ships. The lowest brine treatments (30 ppt for 1 h) caused 100% mortality in several species of cladocerans and copepods collected from oligohaline habitats. Several brackish-water peracarid crustaceans, however, including some that can survive in freshwater as well, required higher brine concentrations and longer exposure durations (45-60 ppt for 3-24 h). The most resilient animals were widely introduced peracarid crustaceans that generally prefer mesohaline habitats but do not tolerate freshwater (required brine treatments of 60-110 ppt for 3-24 h). Brine treatments (30 ppt) also required less time to cause 100% mortality for eight taxa compared with treatments using 34 ppt seawater. Based on these experiments and published data, we present treatment strategies for the ballast tank biota often associated with NOBOB vessels entering the Great Lakes region. We estimate the lethal dosage of brine for 95% of the species in our experiments to be 110 ppt (95% confidence interval, 85-192 ppt) when the exposure time is 1 h and 60 ppt (95% confidence interval, 48-98 ppt) when the exposure duration is 6 h or longer.

Developing Molecular Methods to Identify and Quantify Ballast Water Organisms: A Test Case with Cnidarians

DTIC Science & Technology

2004-04-15

Developing Molecular Methods to Identify and Quantify Ballast Water Organisms: A Test Case with Cnidarians SERDP Project # CP-1251...2004 4. TITLE AND SUBTITLE Developing Molecular Methods to Identify and Quantify Ballast Water Organisms: A Test Case with Cnidarians 5a. CONTRACT... cnidarians ? 9 Indicators of ballast water exchange 9 Materials and Methods 11 Phase I. Specimens 11 DNA

Per capita invasion probabilities: an empirical model to predict rates of invasion via ballast water

USGS Publications Warehouse

Reusser, Deborah A.; Lee, Henry; Frazier, Melanie; Ruiz, Gregory M.; Fofonoff, Paul W.; Minton, Mark S.; Miller, A. Whitman

2013-01-01

Ballast water discharges are a major source of species introductions into marine and estuarine ecosystems. To mitigate the introduction of new invaders into these ecosystems, many agencies are proposing standards that establish upper concentration limits for organisms in ballast discharge. Ideally, ballast discharge standards will be biologically defensible and adequately protective of the marine environment. We propose a new technique, the per capita invasion probability (PCIP), for managers to quantitatively evaluate the relative risk of different concentration-based ballast water discharge standards. PCIP represents the likelihood that a single discharged organism will become established as a new nonindigenous species. This value is calculated by dividing the total number of ballast water invaders per year by the total number of organisms discharged from ballast. Analysis was done at the coast-wide scale for the Atlantic, Gulf, and Pacific coasts, as well as the Great Lakes, to reduce uncertainty due to secondary invasions between estuaries on a single coast. The PCIP metric is then used to predict the rate of new ballast-associated invasions given various regulatory scenarios. Depending upon the assumptions used in the risk analysis, this approach predicts that approximately one new species will invade every 10–100 years with the International Maritime Organization (IMO) discharge standard of 50 μm per m3 of ballast. This approach resolves many of the limitations associated with other methods of establishing ecologically sound discharge standards, and it allows policy makers to use risk-based methodologies to establish biologically defensible discharge standards.

46 CFR 153.217 - Access to enclosed spaces and dedicated ballast tanks.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 5 2014-10-01 2014-10-01 false Access to enclosed spaces and dedicated ballast tanks... DANGEROUS CARGOES SHIPS CARRYING BULK LIQUID, LIQUEFIED GAS, OR COMPRESSED GAS HAZARDOUS MATERIALS Design and Equipment General Vessel Requirements § 153.217 Access to enclosed spaces and dedicated ballast...

46 CFR 153.217 - Access to enclosed spaces and dedicated ballast tanks.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 5 2012-10-01 2012-10-01 false Access to enclosed spaces and dedicated ballast tanks... DANGEROUS CARGOES SHIPS CARRYING BULK LIQUID, LIQUEFIED GAS, OR COMPRESSED GAS HAZARDOUS MATERIALS Design and Equipment General Vessel Requirements § 153.217 Access to enclosed spaces and dedicated ballast...

46 CFR 153.217 - Access to enclosed spaces and dedicated ballast tanks.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 5 2010-10-01 2010-10-01 false Access to enclosed spaces and dedicated ballast tanks... DANGEROUS CARGOES SHIPS CARRYING BULK LIQUID, LIQUEFIED GAS, OR COMPRESSED GAS HAZARDOUS MATERIALS Design and Equipment General Vessel Requirements § 153.217 Access to enclosed spaces and dedicated ballast...

46 CFR 153.217 - Access to enclosed spaces and dedicated ballast tanks.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 5 2011-10-01 2011-10-01 false Access to enclosed spaces and dedicated ballast tanks... DANGEROUS CARGOES SHIPS CARRYING BULK LIQUID, LIQUEFIED GAS, OR COMPRESSED GAS HAZARDOUS MATERIALS Design and Equipment General Vessel Requirements § 153.217 Access to enclosed spaces and dedicated ballast...

46 CFR 153.217 - Access to enclosed spaces and dedicated ballast tanks.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 5 2013-10-01 2013-10-01 false Access to enclosed spaces and dedicated ballast tanks... DANGEROUS CARGOES SHIPS CARRYING BULK LIQUID, LIQUEFIED GAS, OR COMPRESSED GAS HAZARDOUS MATERIALS Design and Equipment General Vessel Requirements § 153.217 Access to enclosed spaces and dedicated ballast...

Assessing the viability of microorganisms in the ballast water of vessels transiting the North Atlantic Ocean.

PubMed

Steichen, Jamie L; Quigg, Antonietta

2015-12-15

Testing phytoplankton viability within ballast tanks and receiving waters of ballast water discharge remain understudied. Potentially harmful dinoflagellates and diatoms are transported via ballast water to Galveston Bay, Texas (USA), home to three major ports: Houston, Texas City and Galveston. Ballast water from vessels transiting the North Atlantic Ocean was inoculated into treatments representing low and high salinity conditions similar to the Ports of Houston and Galveston respectively. Phytoplankton in ballast water growout experiments were deemed viable and showed growth in low and mid salinities with nutrient enrichment. Molecular methods identified several genera: Dinophysis, Gymnodinium, Gyrodinium, Heterocapsa, Peridinium, Scrippsiella, Chaetoceros and Nitzschia. These phytoplankton genera were previously identified in Galveston Bay except Scrippsiella. Phytoplankton, including those capable of forming harmful algal blooms leading to fish and shellfish kills, are transported to Galveston Bay via ballast water, and are viable when introduced to similar salinity conditions found in Galveston Bay ports. Copyright © 2015 Elsevier Ltd. All rights reserved.

Comparisons of interdisciplinary ballast water treatment systems and operational experiences from ships.

PubMed

Bakalar, Goran

2016-01-01

There are high functioning and low functioning ballast water treatment systems on board ships. In this study, five systems were analysed so as to methodically examine the operational difficulties for ship crew members while giving important consideration to sustainable environment practices. Multi-criteria analysis, a questionnaire, survey and interviews were used as the research method so as to ascertain and corroborate existing problems on board ships, and the reliability of the systems was calculated. The co-insistency, maintenance and the efficiency of the systems, were shown as being the major problem as there are no systems for tracking ship ballast operations from land. The treatment system that used oxidants was, through multi criteria analysis, evaluated as being the best and was ranked first. However, the survey results showed that the ship's crew had serious problems with this system which difficult to solve during the ship's operations with cargo. The deoxygenation system was the most appropriate according to ballast water treatment criteria in the port or at sea. The treatment system which used electrolysis with oxidant was better in terms of efficacy and the treatment system electrolysis with ultra violet light was better in terms of the criterion environment pollution footprint. During further research, it was shown that 7 % of the surveyed crew members had major problems with operating ballast water treatment systems, including the system which was ranked first through multi criteria analysis. They by-passed these systems while continuing to ballast or de-ballast. It was calculated that of the total time needed for the ballast water treatment system operation, 9 % of this time was used for repairs or maintenance of the systems. Some examples are changing a used UV bulb, cleaning the filter or controlling the amount of oxidant which would be discharged into the sea. A conclusion was made and solution was suggested. The study results emphasised

Density Matters: Review of Approaches to Setting Organism-Based Ballast Water Discharge Standards

EPA Science Inventory

As part of their effort to develop national ballast water discharge standards under NPDES permitting, the Office of Water requested that WED scientists identify and review existing approaches to generating organism-based discharge standards for ballast water. Six potential appro...

Ships' Ballast Water Treatment by Chlorination Can Generate Toxic Trihalomethanes.

PubMed

Hernandez, Marco R; Ismail, Nargis; Drouillard, Ken G; MacIsaac, Hugh J

2017-08-01

The International Maritime Organization (IMO) will enforce a new abundance-based performance standard for ballast water in September, 2017. Strong oxidants, like chlorine, have been proposed as a method for achieving this standard. However chlorine treatment of ballast water can produce hazardous trihalomethanes. We assessed maximum trihalomethane production from one chlorine dose for three types of ballast water (fresh, brackish and marine) and three levels of total organic carbon (TOC) concentration (natural, filtered, enhanced). While the current standard test considers a 5 day voyage, there is a high possibility of shorter trips and sudden change of plans that will release treated waters in the environment. Water source and TOC significantly affected trihalomethane production, with the highest amounts generated in brackish waters and enhanced TOC concentration. The concentration of brominated trihalomethanes increased from background levels and was highest in brackish water, followed by marine and fresh water.

A shipboard comparison of analytic methods for ballast water compliance monitoring

NASA Astrophysics Data System (ADS)

Bradie, Johanna; Broeg, Katja; Gianoli, Claudio; He, Jianjun; Heitmüller, Susanne; Curto, Alberto Lo; Nakata, Akiko; Rolke, Manfred; Schillak, Lothar; Stehouwer, Peter; Vanden Byllaardt, Julie; Veldhuis, Marcel; Welschmeyer, Nick; Younan, Lawrence; Zaake, André; Bailey, Sarah

2018-03-01

Promising approaches for indicative analysis of ballast water samples have been developed that require study in the field to examine their utility for determining compliance with the International Convention for the Control and Management of Ships' Ballast Water and Sediments. To address this gap, a voyage was undertaken on board the RV Meteor, sailing the North Atlantic Ocean from Mindelo (Cape Verde) to Hamburg (Germany) during June 4-15, 2015. Trials were conducted on local sea water taken up by the ship's ballast system at multiple locations along the trip, including open ocean, North Sea, and coastal water, to evaluate a number of analytic methods that measure the numeric concentration or biomass of viable organisms according to two size categories (≥ 50 μm in minimum dimension: 7 techniques, ≥ 10 μm and < 50 μm: 9 techniques). Water samples were analyzed in parallel to determine whether results were similar between methods and whether rapid, indicative methods offer comparable results to standard, time- and labor-intensive detailed methods (e.g. microscopy) and high-end scientific approaches (e.g. flow cytometry). Several promising indicative methods were identified that showed high correlation with microscopy, but allow much quicker processing and require less expert knowledge. This study is the first to concurrently use a large number of analytic tools to examine a variety of ballast water samples on board an operational ship in the field. Results are useful to identify the merits of each method and can serve as a basis for further improvement and development of tools and methodologies for ballast water compliance monitoring.

77 FR 17082 - Standards for Living Organisms in Ships' Ballast Water Discharged in U.S. Waters: Final...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-03-23

... Organisms in Ships' Ballast Water Discharged in U.S. Waters: Final Programmatic Environmental Impact... entitled ``Standards for Living Organisms in Ships' Ballast Water Discharged in U.S. Waters'' (Docket No... impacts associated with the establishment of a ballast water discharge standard for the allowable...

NBIC: National Ballast Information Clearinghouse News

Science.gov Websites

SERC >| Marine Invasions Research Lab NBIC logo National Ballast Information Clearinghouse Smithsonian Environmental Research Center Logo US Coast Guard Logo Submit BW Report | Search NBIC Database | NBIC Research & Development | NBIC News | Home NBIC News Recent News 29 March 2016 Based on

Modeling Ballasted Tracks for Runoff Coefficient C

DOT National Transportation Integrated Search

2012-08-01

In this study, the Regional Transportation District (RTD)s light rail tracks were modeled to determine the Rational Method : runoff coefficient, C, values corresponding to ballasted tracks. To accomplish this, a laboratory study utilizing a : rain...

75 FR 71570 - Energy Conservation Program: Test Procedures for Fluorescent Lamp Ballasts

Federal Register 2010, 2011, 2012, 2013, 2014

2010-11-24

... improve energy efficiency. Part A of Title III (42 U.S.C. 6291-6309) establishes the ``Energy Conservation... ballasts (ballasts). (42 U.S.C. 6291(1), (2) and 6292(a)(13)) Under EPCA, the overall program consists... the public an opportunity to present oral and written comments on them. (42 U.S.C. 6293(b)(2)) Finally...

Bacterial Diversity in Ships' Ballast Water, Ballast-Water Exchange, and Implications for Ship-Mediated Dispersal of Microorganisms.

PubMed

Lymperopoulou, Despoina S; Dobbs, Fred C

2017-02-21

Using next-generation DNA sequencing of the 16S rRNA gene, we analyzed the composition and diversity of bacterial assemblages in ballast water from tanks of 17 commercial ships arriving to Hampton Roads, Virginia (USA) following voyages in the North Atlantic Ocean. Amplicon sequencing analysis showed the heterogeneous assemblages were (1) dominated by Alpha- and Gammaproteobacteria, Bacteroidetes, and unclassified Bacteria; (2) temporally distinct (June vs August/September); and (3) highly fidelitous among replicate samples. Whether tanks were exchanged at sea or not, their bacterial assemblages differed from those of local, coastal water. Compositional data suggested at-sea exchange did not fully flush coastal Bacteria from all tanks; there were several instances of a genetic geographic signal. Quantitative PCR yielded no Escherichia coli and few instances of Vibrio species. Salinity, but not ballast-water age or temperature, contributed significantly to bacterial diversity. Whether anthropogenic mixing of marine Bacteria restructures their biogeography remains to be tested.

Flow cytometry and conventional enumeration of microorganisms in ships' ballast water and marine samples.

PubMed

Joachimsthal, Eva L; Ivanov, Volodymyr; Tay, Joo-Hwa; Tay, Stephen T-L

2003-03-01

Conventional methods for bacteriological testing of water quality take long periods of time to complete. This makes them inappropriate for a shipping industry that is attempting to comply with the International Maritime Organization's anticipated regulations for ballast water discharge. Flow cytometry for the analysis of marine and ship's ballast water is a comparatively fast and accurate method. Compared to a 5% standard error for flow cytometry analysis the standard methods of culturing and epifluorescence analysis have errors of 2-58% and 10-30%, respectively. Also, unlike culturing methods, flow cytometry is capable of detecting both non-viable and viable but non-culturable microorganisms which can still pose health risks. The great variability in both cell concentrations and microbial content for the samples tested is an indication of the difficulties facing microbial monitoring programmes. The concentration of microorganisms in the ballast tank was generally lower than in local seawater. The proportion of aerobic, microaerophilic, and facultative anaerobic microorganisms present appeared to be influenced by conditions in the ballast tank. The gradual creation of anaerobic conditions in a ballast tank could lead to the accumulation of facultative anaerobic microorganisms, which might represent a potential source of pathogenic species.

Coagulant plus ballast technique provides a rapid mitigation of cyanobacterial nuisance

PubMed Central

de Magalhães, Leonardo; Miranda, Marcela; Mucci, Maíra; van Oosterhout, Frank; Huszar, Vera L. M.; Marinho, Marcelo M.; Lima, Eduardo R. A.; Lürling, Miquel

2017-01-01

Cyanobacteria blooms are a risk to environmental health and public safety due to the potent toxins certain cyanobacteria can produce. These nuisance organisms can be removed from water bodies by biomass flocculation and sedimentation. Here, we studied the efficacy of combinations of a low dose coagulant (poly-aluminium chloride—PAC—or chitosan) with different ballast compounds (red soil, bauxite, gravel, aluminium modified zeolite and lanthanum modified bentonite) to remove cyanobacterial biomass from water collected in Funil Reservoir (Brazil). We tested the effect of different cyanobacterial biomass concentrations on removal efficiency. We also examined if zeta potential was altered by treatments. Addition of low doses of PAC and chitosan (1–8 mg Al L-1) to the cyanobacterial suspensions caused flock formation, but did not settle the cyanobacteria. When those low dose coagulants were combined with ballast, effective settling in a dose-dependent way up to 99.7% removal of the flocks could be achieved without any effect on the zeta potential and thus without potential membrane damage. Removal efficacy was influenced by the cyanobacterial biomass and at higher biomass more ballast was needed to achieve good removal. The combined coagulant-ballast technique provides a promising alternative to algaecides in lakes, ponds and reservoirs. PMID:28598977

Heavy metal levels of ballast waters in commercial ships entering Bushehr port along the Persian Gulf.

PubMed

Dobaradaran, Sina; Soleimani, Farshid; Nabipour, Iraj; Saeedi, Reza; Mohammadi, Mohammad Javad

2018-01-01

In this study we report the concentration levels of heavy metals (including Pb, Cd, Hg, Cr, Ni, Fe, Mn, Cu) in ballast water of commercial ships, entering Bushehr port for the first time in the region of the Persian Gulf. The concentration levels of Cu and Fe in all samples of the ballast water were higher compared with the coastal waters of Bushehr port. In the case of Cd, 76.47% of samples had higher concentration level compared with the coastal waters of Bushehr port. Results showed that in a long term the ballast water has the potential to change the chemical quality in marine environments and also may affect the human health and marine ecosystem where ships discharge their ballast water. Therefore, permanent monitoring as well as treatment of ballast water before discharging is crucial to keep the marine environment health. Copyright © 2017 Elsevier Ltd. All rights reserved.

46 CFR 153.208 - Ballast equipment.

Code of Federal Regulations, 2013 CFR

2013-10-01

... BULK LIQUID, LIQUEFIED GAS, OR COMPRESSED GAS HAZARDOUS MATERIALS Design and Equipment General Vessel... engine room or accommodation space. (b) Piping used only to fill a dedicated ballast tank adjacent to a cargo tank may enter an engine room or accommodation space if the piping has a valve or valving...

46 CFR 153.208 - Ballast equipment.

Code of Federal Regulations, 2011 CFR

2011-10-01

... BULK LIQUID, LIQUEFIED GAS, OR COMPRESSED GAS HAZARDOUS MATERIALS Design and Equipment General Vessel... engine room or accommodation space. (b) Piping used only to fill a dedicated ballast tank adjacent to a cargo tank may enter an engine room or accommodation space if the piping has a valve or valving...

46 CFR 153.208 - Ballast equipment.

Code of Federal Regulations, 2010 CFR

2010-10-01

... BULK LIQUID, LIQUEFIED GAS, OR COMPRESSED GAS HAZARDOUS MATERIALS Design and Equipment General Vessel... engine room or accommodation space. (b) Piping used only to fill a dedicated ballast tank adjacent to a cargo tank may enter an engine room or accommodation space if the piping has a valve or valving...

Mechanics of Ballast Compaction. Volume 4 : Lab. Invest. the Effects of Field Compaction Mechanisms

DOT National Transportation Integrated Search

1982-03-01

This report describes a preliminary series of laboratory tests which attempt to simulate some of the effects of maintenance procedures and traffic on the physical state of ballast as measured by the ballast density test, plate load test, and lateral ...

Ecosystem under pressure: ballast water discharge into Galveston Bay, Texas (USA) from 2005 to 2010.

PubMed

Steichen, Jamie L; Windham, Rachel; Brinkmeyer, Robin; Quigg, Antonietta

2012-04-01

Ballast water exchange processes facilitate the dispersal and unnatural geographic expansion of phytoplankton, including harmful algal bloom species. From 2005 to 2010, over 45,000 vessels (≈ 8000 annually) travelled across Galveston Bay (Texas, USA) to the deep-water ports of Houston (10th largest in the world), Texas City and Galveston. These vessels (primarily tankers and bulkers) discharged ≈ 1.2 × 10(8) metrictons of ballast water; equivalent to ≈ 3.4% of the total volume of the Bay. Over half of the ballast water discharged had a coastwise origin, 96% being from US waters. Galveston Bay has fewer non-indigenous species but receives a higher volume of ballast water discharge, relative to the highly invaded Chesapeake and San Francisco Bays. Given the magnitude of shipping traffic, the role of Galveston Bay, both as a recipient and donor region of non-indigenous phytoplankton species is discussed here in terms of the invasibility risk to this system by way of ballast water. Copyright © 2012 Elsevier Ltd. All rights reserved.

Asbestos quantification in track ballast, a complex analytical problem

NASA Astrophysics Data System (ADS)

Cavallo, Alessandro

2016-04-01

Track ballast forms the trackbeb upon which railroad ties are laid. It is used to bear the load from the railroad ties, to facilitate water drainage, and also to keep down vegetation. It is typically made of angular crushed stone, with a grain size between 30 and 60 mm, with good mechanical properties (high compressive strength, freeze - thaw resistance, resistance to fragmentation). The most common rock types are represented by basalts, porphyries, orthogneisses, some carbonatic rocks and "green stones" (serpentinites, prasinites, amphibolites, metagabbros). Especially "green stones" may contain traces, and sometimes appreciable amounts of asbestiform minerals (chrysotile and/or fibrous amphiboles, generally tremolite - actinolite). In Italy, the chrysotile asbestos mine in Balangero (Turin) produced over 5 Mt railroad ballast (crushed serpentinites), which was used for the railways in northern and central Italy, from 1930 up to 1990. In addition to Balangero, several other serpentinite and prasinite quarries (e.g. Emilia Romagna) provided the railways ballast up to the year 2000. The legal threshold for asbestos content in track ballast is established in 1000 ppm: if the value is below this threshold, the material can be reused, otherwise it must be disposed of as hazardous waste, with very high costs. The quantitative asbestos determination in rocks is a very complex analytical issue: although techniques like TEM-SAED and micro-Raman are very effective in the identification of asbestos minerals, a quantitative determination on bulk materials is almost impossible or really expensive and time consuming. Another problem is represented by the discrimination of asbestiform minerals (e.g. chrysotile, asbestiform amphiboles) from the common acicular - pseudo-fibrous varieties (lamellar serpentine minerals, prismatic/acicular amphiboles). In this work, more than 200 samples from the main Italian rail yards were characterized by a combined use of XRD and a special SEM

33 CFR 157.09 - Segregated ballast.

Code of Federal Regulations, 2010 CFR

2010-07-01

...) POLLUTION RULES FOR THE PROTECTION OF THE MARINE ENVIRONMENT RELATING TO TANK VESSELS CARRYING OIL IN BULK... more must have segregated ballast tanks that have a total capacity to allow the vessel to meet the draft and trim requirements in paragraph (b) of this section without recourse to the use of oil tanks...

Possible Ballast Water Transfer of Lionfish to the Eastern Pacific Ocean.

PubMed

MacIsaac, Hugh J; De Roy, Emma M; Leung, Brian; Grgicak-Mannion, Alice; Ruiz, Gregory M

2016-01-01

The Indo-Pacific Red Lionfish was first reported off the Florida coast in 1985, following which it has spread across much of the SE USA, Gulf of Mexico, and Caribbean Sea. Lionfish negatively impact fish and invertebrate assemblages and abundances, thus further spread is cause for concern. To date, the fish has not been reported on the Pacific coast of North or Central America. Here we examine the possibility of ballast water transfer of lionfish from colonized areas in the Atlantic Ocean to USA ports on the Pacific coast. Over an eight-year period, we documented 27 commercial vessel-trips in which ballast water was loaded in colonized sites and later discharged untreated into Pacific coast ports in the USA. California had the highest number of discharges including San Francisco Bay and Los Angeles-Long Beach. A species distribution model suggests that the probability of lionfish establishment is low for the western USA, Colombia and Panama, low to medium for Costa Rica, Nicaragua, El Salvador and Guatemala, medium to high for mainland Ecuador, and very high for western Mexico, Peru and the Galapagos Islands. Given the species' intolerance of freshwater conditions, we propose that ballast water exchange be conducted in Gatún Lake, Panama for western-bound vessels carrying 'risky' ballast water to prevent invasion of the eastern Pacific Ocean.

Possible Ballast Water Transfer of Lionfish to the Eastern Pacific Ocean

PubMed Central

MacIsaac, Hugh J.; De Roy, Emma M.; Leung, Brian; Grgicak-Mannion, Alice; Ruiz, Gregory M.

2016-01-01

The Indo-Pacific Red Lionfish was first reported off the Florida coast in 1985, following which it has spread across much of the SE USA, Gulf of Mexico, and Caribbean Sea. Lionfish negatively impact fish and invertebrate assemblages and abundances, thus further spread is cause for concern. To date, the fish has not been reported on the Pacific coast of North or Central America. Here we examine the possibility of ballast water transfer of lionfish from colonized areas in the Atlantic Ocean to USA ports on the Pacific coast. Over an eight-year period, we documented 27 commercial vessel-trips in which ballast water was loaded in colonized sites and later discharged untreated into Pacific coast ports in the USA. California had the highest number of discharges including San Francisco Bay and Los Angeles-Long Beach. A species distribution model suggests that the probability of lionfish establishment is low for the western USA, Colombia and Panama, low to medium for Costa Rica, Nicaragua, El Salvador and Guatemala, medium to high for mainland Ecuador, and very high for western Mexico, Peru and the Galapagos Islands. Given the species’ intolerance of freshwater conditions, we propose that ballast water exchange be conducted in Gatún Lake, Panama for western-bound vessels carrying ‘risky’ ballast water to prevent invasion of the eastern Pacific Ocean. PMID:27806076

International dissemination of epidemic Vibrio cholerae by cargo ship ballast and other nonpotable waters.

PubMed

McCarthy, S A; Khambaty, F M

1994-07-01

In 1991 and 1992, toxigenic Vibrio cholerae O1, serotype Inaba, biotype El Tor, was recovered from nonpotable (ballast, bilge, and sewage) water from five cargo ships docked in ports of the U.S. Gulf of Mexico. Four of these ships had taken on ballast water in cholera-infected countries; the fifth took on ballast in a noninfected country. Isolates examined by pulsed-field gel electrophoresis were indistinguishable from the Latin American epidemic strain, C6707; however, they differed significantly from the endemic Gulf Coast strain (VRL 1984), the sixth-pandemic strain (569-B), and a V. cholerae non-O1 strain isolated from a ship arriving from a foreign port. On the basis of our findings, the Food and Drug Administration recommended that the U.S. Coast Guard issue an advisory to shipping agents and captains requesting that ballast waters be exchanged on the high seas before entry of ships into U.S. ports.

International dissemination of epidemic Vibrio cholerae by cargo ship ballast and other nonpotable waters.

PubMed Central

McCarthy, S A; Khambaty, F M

1994-01-01

In 1991 and 1992, toxigenic Vibrio cholerae O1, serotype Inaba, biotype El Tor, was recovered from nonpotable (ballast, bilge, and sewage) water from five cargo ships docked in ports of the U.S. Gulf of Mexico. Four of these ships had taken on ballast water in cholera-infected countries; the fifth took on ballast in a noninfected country. Isolates examined by pulsed-field gel electrophoresis were indistinguishable from the Latin American epidemic strain, C6707; however, they differed significantly from the endemic Gulf Coast strain (VRL 1984), the sixth-pandemic strain (569-B), and a V. cholerae non-O1 strain isolated from a ship arriving from a foreign port. On the basis of our findings, the Food and Drug Administration recommended that the U.S. Coast Guard issue an advisory to shipping agents and captains requesting that ballast waters be exchanged on the high seas before entry of ships into U.S. ports. Images PMID:8074532

46 CFR 153.1502 - Fixed ballast relocation.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 5 2012-10-01 2012-10-01 false Fixed ballast relocation. 153.1502 Section 153.1502 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) CERTAIN BULK DANGEROUS CARGOES SHIPS CARRYING BULK LIQUID, LIQUEFIED GAS, OR COMPRESSED GAS HAZARDOUS MATERIALS Operations Maintenance § 153...

46 CFR 153.1502 - Fixed ballast relocation.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 5 2013-10-01 2013-10-01 false Fixed ballast relocation. 153.1502 Section 153.1502 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) CERTAIN BULK DANGEROUS CARGOES SHIPS CARRYING BULK LIQUID, LIQUEFIED GAS, OR COMPRESSED GAS HAZARDOUS MATERIALS Operations Maintenance § 153...

46 CFR 153.1502 - Fixed ballast relocation.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 5 2014-10-01 2014-10-01 false Fixed ballast relocation. 153.1502 Section 153.1502 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) CERTAIN BULK DANGEROUS CARGOES SHIPS CARRYING BULK LIQUID, LIQUEFIED GAS, OR COMPRESSED GAS HAZARDOUS MATERIALS Operations Maintenance § 153...

46 CFR 153.1502 - Fixed ballast relocation.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 5 2010-10-01 2010-10-01 false Fixed ballast relocation. 153.1502 Section 153.1502 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) CERTAIN BULK DANGEROUS CARGOES SHIPS CARRYING BULK LIQUID, LIQUEFIED GAS, OR COMPRESSED GAS HAZARDOUS MATERIALS Operations Maintenance § 153...

46 CFR 153.1502 - Fixed ballast relocation.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 5 2011-10-01 2011-10-01 false Fixed ballast relocation. 153.1502 Section 153.1502 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) CERTAIN BULK DANGEROUS CARGOES SHIPS CARRYING BULK LIQUID, LIQUEFIED GAS, OR COMPRESSED GAS HAZARDOUS MATERIALS Operations Maintenance § 153...

Assessment of design tools and criteria for urban rail track structures : volume 1. at-grade tie-ballast track.

DOT National Transportation Integrated Search

1974-04-30

The report presents the results of a critical review of the technical factors which govern the design and performance of at-grade tie-ballast track for urban rail systems. The assessment of current design practice is based on a review of the literatu...

Stratification of living organisms in ballast tanks: how do organism concentrations vary as ballast water is discharged?

PubMed

First, Matthew R; Robbins-Wamsley, Stephanie H; Riley, Scott C; Moser, Cameron S; Smith, George E; Tamburri, Mario N; Drake, Lisa A

2013-05-07

Vertical migrations of living organisms and settling of particle-attached organisms lead to uneven distributions of biota at different depths in the water column. In ballast tanks, heterogeneity could lead to different population estimates depending on the portion of the discharge sampled. For example, concentrations of organisms exceeding a discharge standard may not be detected if sampling occurs during periods of the discharge when concentrations are low. To determine the degree of stratification, water from ballast tanks was sampled at two experimental facilities as the tanks were drained after water was held for 1 or 5 days. Living organisms ≥50 μm were counted in discrete segments of the drain (e.g., the first 20 min of the drain operation, the second 20 min interval, etc.), thus representing different strata in the tank. In 1 and 5 day trials at both facilities, concentrations of organisms varied among drain segments, and the patterns of stratification varied among replicate trials. From numerical simulations, the optimal sampling strategy for stratified tanks is to collect multiple time-integrated samples spaced relatively evenly throughout the discharge event.

Electronic Dimmable Ballasts for High-Intensity Discharge Sodium Vapor and Metal Halide Lamps

NASA Technical Reports Server (NTRS)

Boulanger, Richard

2002-01-01

Two types of high-intensity discharge lamps were tested using dimmable ballasts. The main purpose for evaluating this lighting system was to determine its efficacy for saving power. Whereas previous variable level lighting systems for HID lamps in Advanced Life Support applications were adjustable in two or three steps using capacitive switching, this system allows for continuously adjustable lamp output. This type of lighting system when used as part of an Advanced Life Support biomass production system would provide only the amount of light energy a crop needed at any particular point in its growth cycle. Since most of the equivalent system mass in an ALS system is from the light energy required to grow the crops, controlling that light energy dynamically over a continuous range of operation would dramatically reduce the power consumption and reduce system mass.

Enumerating sparse organisms in ships' ballast water: why counting to 10 is not so easy

EPA Science Inventory

To reduce ballast water-borne aquatic invasions worldwide, the International Maritime Organization and United States Coast Guard have each proposed discharge standards specifying maximum concentrations of living biota that may be released in ships’ ballast water (BW), but these r...

Inactivation of Heterosigma akashiwo in ballast water by circular orifice plate-generated hydrodynamic cavitation.

PubMed

Feng, Daolun; Zhao, Jie; Liu, Tian

2016-01-01

The discharge of alien ballast water is a well-known, major reason for marine species invasion. Here, circular orifice plate-generated hydrodynamic cavitation was used to inactivate Heterosigma akashiwo in ballast water. In comparison with single- and multihole orifice plates, the conical-hole orifice plate yielded the highest inactivation percentage, 51.12%, and consumed only 6.84% energy (based on a 50% inactivation percentage). Repeating treatment, either using double series-connection or circling inactivation, elevated the inactivation percentage, yet consumed much more energy. The results indicate that conical-hole-generated hydrodynamic cavitation shows great potential as a pre-inactivation method for ballast water treatment.

Ballast degradation characterized through triaxial test : research results.

DOT National Transportation Integrated Search

2016-06-01

Transportation Technology Center, Inc. (TTCI) : has supported the development of a large-scale : triaxial test device (Figure 1) for testing ballast : size aggregate materials at the University of : Illinois at Urbana-Champaign (UIUC). This new : tes...

Mitigating ballast fouling and enhancing rail freight capacity.

DOT National Transportation Integrated Search

2012-11-01

In this report, an application using polyurethane void filling and particle bonding technology for stabilizing ballast is : evaluated. Application of rigid-polyurethane foam (RPF) as an in situ stabilization method does not require premixing : with a...

46 CFR 162.060-30 - Testing requirements for ballast water management system (BWMS) components.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 6 2012-10-01 2012-10-01 false Testing requirements for ballast water management system (BWMS) components. 162.060-30 Section 162.060-30 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) EQUIPMENT, CONSTRUCTION, AND MATERIALS: SPECIFICATIONS AND APPROVAL ENGINEERING EQUIPMENT Ballast Water Management Systems § 162.060...

A comparison of six different ballast water treatment systems based on UV radiation, electrochlorination and chlorine dioxide.

PubMed

Stehouwer, Peter Paul; Buma, Anita; Peperzak, Louis

2015-01-01

The spread of aquatic invasive species through ballast water is a major ecological and economical threat. Because of this, the International Maritime Organization (IMO) set limits to the concentrations of organisms allowed in ballast water. To meet these limits, ballast water treatment systems (BWTSs) were developed. The main techniques used for ballast water treatment are ultraviolet (UV) radiation and electrochlorination (EC). In this study, phytoplankton regrowth after treatment was followed for six BWTSs. Natural plankton communities were treated and incubated for 20 days. Growth, photosystem II efficiency and species composition were followed. The three UV systems all showed similar patterns of decrease in phytoplankton concentrations followed by regrowth. The two EC and the chlorine dioxide systems showed comparable results. However, UV- and chlorine-based treatment systems showed significantly different responses. Overall, all BWTSs reduced phytoplankton concentrations to below the IMO limits, which represents a reduced risk of aquatic invasions through ballast water.

33 CFR 151.2045 - What are the mandatory recordkeeping requirements for vessels equipped with ballast tanks that...

Code of Federal Regulations, 2010 CFR

2010-07-01

... HOMELAND SECURITY (CONTINUED) POLLUTION VESSELS CARRYING OIL, NOXIOUS LIQUID SUBSTANCES, GARBAGE, MUNICIPAL OR COMMERCIAL WASTE, AND BALLAST WATER Ballast Water Management for Control of Nonindigenous Species...

Occurrences, composition profiles and source identifications of polycyclic aromatic hydrocarbons (PAHs), polybrominated diphenyl ethers (PBDEs) and polychlorinated biphenyls (PCBs) in ship ballast sediments.

PubMed

Su, Peng-Hao; Lv, Bao-Yi; Tomy, Gregg T; Xu, Jin-Xiang; Tian, Wen; Hou, Chun-Yan; Yin, Fang; Li, Yi-Fan; Feng, Dao-Lun

2017-02-01

The aim of this study was to investigate the levels of persistent organic pollutants (POPs) including polycyclic aromatic hydrocarbons (PAHs), polybrominated diphenyl ethers (PBDEs) and polychlorinated biphenyls (PCBs) in ship ballast sediments. The ballast sediment samples were collected from six merchant ships docked in 2015 in Jiangyin City, China. Ballast sediments represent a potential vector for the transport of POPs and invasive species between marine environments. An attempt was also made to determine the sources of these compounds in the ballast sediment. The results indicated ballast sediments generally contain greater amounts of BDE-209 and comparable amounts of PAHs, PBDEs (exclusive of BDE-209) and PCBs compared to those in marine surface sediments. Based on the sediment quality guidelines, PAHs and PCBs in ballast sediments were estimated to have median or high potential of posing ecological risks, respectively, to marine life if ballast sediments were disposed without specific treatment. POPs in ballast sediments were derived from multiple sources with atmospheric deposition being an important origin. Ship activities including diesel exhaust and illegal oil sewage discharge were considerable contributors of certain individual POPs to ballast sediments. Our study is important because it represents the first report on levels, health risk assessment and source apportionments of POPs in ballast sediments and is a first step in the implementation of specific ballast sediment management measures. Copyright © 2016 Elsevier Ltd. All rights reserved.

33 CFR 157.10a - Segregated ballast tanks, crude oil washing systems, and dedicated clean ballast tanks for...

Code of Federal Regulations, 2011 CFR

2011-07-01

... tanks with a total capacity to meet the draft and trim requirements in paragraph (d) of this section; or...) Segregated ballast tanks with a total capacity to meet the draft and trim requirements in paragraph (d) of... trim requirements in paragraph (d) of this section and that meet the design and equipment requirements...

33 CFR 157.10a - Segregated ballast tanks, crude oil washing systems, and dedicated clean ballast tanks for...

Code of Federal Regulations, 2010 CFR

2010-07-01

... tanks with a total capacity to meet the draft and trim requirements in paragraph (d) of this section; or...) Segregated ballast tanks with a total capacity to meet the draft and trim requirements in paragraph (d) of... trim requirements in paragraph (d) of this section and that meet the design and equipment requirements...

46 CFR 162.060-16 - Changes to an approved ballast water management system (BWMS).

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 6 2012-10-01 2012-10-01 false Changes to an approved ballast water management system (BWMS). 162.060-16 Section 162.060-16 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) EQUIPMENT, CONSTRUCTION, AND MATERIALS: SPECIFICATIONS AND APPROVAL ENGINEERING EQUIPMENT Ballast Water Management Systems § 162.060-16 Changes to...

Ballasting by cryogenic gypsum enhances carbon export in a Phaeocystis under-ice bloom.

PubMed

Wollenburg, J E; Katlein, C; Nehrke, G; Nöthig, E-M; Matthiessen, J; Wolf-Gladrow, D A; Nikolopoulos, A; Gázquez-Sanchez, F; Rossmann, L; Assmy, P; Babin, M; Bruyant, F; Beaulieu, M; Dybwad, C; Peeken, I

2018-05-16

Mineral ballasting enhances carbon export from the surface to the deep ocean; however, little is known about the role of this process in the ice-covered Arctic Ocean. Here, we propose gypsum ballasting as a new mechanism that likely facilitated enhanced vertical carbon export from an under-ice phytoplankton bloom dominated by the haptophyte Phaeocystis. In the spring 2015 abundant gypsum crystals embedded in Phaeocystis aggregates were collected throughout the water column and on the sea floor at a depth below 2 km. Model predictions supported by isotopic signatures indicate that 2.7 g m -2 gypsum crystals were formed in sea ice at temperatures below -6.5 °C and released into the water column during sea ice melting. Our finding indicates that sea ice derived (cryogenic) gypsum is stable enough to survive export to the deep ocean and serves as an effective ballast mineral. Our findings also suggest a potentially important and previously unknown role of Phaeocystis in deep carbon export due to cryogenic gypsum ballasting. The rapidly changing Arctic sea ice regime might favour this gypsum gravity chute with potential consequences for carbon export and food partitioning between pelagic and benthic ecosystems.

Evaluation of approaches to quantify total residual oxidants in ballast water management systems employing chlorine for disinfection.

PubMed

Zimmer-Faust, Amity G; Ambrose, Richard F; Tamburri, Mario N

2014-01-01

With the maturation and certification of several ballast water management systems that employ chlorine as biocide to prevent the spread of invasive species, there is a clear need for accurate and reliable total residual oxidants (TRO) technology to monitor treatment dose and assure the environmental safety of treated water discharged from ships. In this study, instruments used to measure TRO in wastewater and drinking water applications were evaluated for their performance in scenarios mimicking a ballast water treatment application (e.g., diverse hold times, temperatures, and salinities). Parameters chosen for testing these technologies in the past do not reflect conditions expected during ballast water treatment. Salinity, temperature, and oxidant concentration all influenced the response of amperometric sensors. Oxidation reduction potential (ORP) sensors performed more consistently than amperometric sensors under different conditions but it may be difficult to correlate ORP and TRO measurements for the multitude of biogeochemical conditions found naturally in ballast water. N,N-diethyl-p-phenylenediamine (DPD) analyzers and amperometric sensors were also tested under intermittent sampling conditions mimicking a ballasting scenario, with cyclical dosage and discharge operations. When sampling was intermittent, amperometric sensors required excessive response and conditioning times, whereas DPD analyzers provided reasonable estimates of TRO under the ballasting scenario.

Direct current ballast circuit for metal halide lamp

NASA Technical Reports Server (NTRS)

Lutus, P. (Inventor)

1981-01-01

A direct current ballast circuit for a two electrode metal halide lamp is described. Said direct current ballast circuit includes a low voltage DC input and a high frequency power amplifier and power transformer for developing a high voltage output. The output voltage is rectified by diodes and filtered by inductor and capacitor to provide a regulated DC output through commutating diodes to one terminal of the lamp at the output terminal. A feedback path from the output of the filter capacitor through the bias resistor to power the high frequency circuit which includes the power amplifier and the power transformer for sustaining circuit operations during low voltage transients on the input DC supply is described. A current sensor connected to the output of the lamp through terminal for stabilizing lamp current following breakdown of the lamp is described.

Zooplankton sensitivity and phytoplankton regrowth for ballast water treatment with advanced oxidation processes.

PubMed

García-Garay, Juan; Franco-Herrera, Andrés; Machuca-Martinez, Fiderman

2018-05-26

The ballasting and de-ballasting of ships are two necessary operations with ballast water that provide stability for safe navigation. Empty ships must ballast tanks with water, which contains living organisms and subsequently carries them away from their original distribution. De-ballasting represents an input of still viable zooplankton, phytoplankton, and microorganisms in the destination port, leading to the introduction of alien species, and consequently, the introduction of organisms will alter the local biodiversity. Ballast water treatment is necessary to comply with the International Maritime Organization (IMO) for the maximum viable organisms permitted. It is known that UVC eliminates microorganisms, but there are few studies on the other taxonomical groups, such as phytoplankton and zooplankton. The advance oxidation processes (AOPs) with UV-C can be a good alternative to manage the problem of ballast water, primarily for microorganisms. However, for larger organisms, there is more resistance, and, a stage with filtration (by physical filtration or hydrocyclone) is usually required. The filter can fail, or certain zooplankton organisms can escape across the filter and go to the AOPs or UVC reactor. According to the taxonomic group, there can be a different sensitivity to the treatment, and one could survive and generate a risk. The AOPs tested were natural solar radiation (RAD), UV/H 2 O 2 , UV/TiO 2 , UV/TiO 2 /H 2 O 2 , and UV/TiO 2 /H 2 O 2 /RAD. Natural sea water was pumped and treated with the AOPs. The vital zooplankton organisms counted were polychaetes, cladocerans, ostracods, nauplii and calanoid, cyclopoid, and harpacticoid copepods. For the phytoplankton, the abundance was estimated, and the photosystem II efficiency was determined. To evaluate the phytoplankton regrowth after the treatments, the treated water was stored and populations counted for 20 days. The most effective treatment for the zooplankton groups was UVC/H 2 O 2 . Regarding the

Development of an ATP assay for rapid onboard testing to detect living microorganisms in ballast water

NASA Astrophysics Data System (ADS)

Hyun, Bonggil; Cha, Hyung-Gon; Lee, Nayoung; Yum, Seungshic; Baek, Seung Ho; Shin, Kyoungsoon

2018-03-01

Ballast water is a principal pathway for the introduction of pathogens and non-indigenous species to ports worldwide. The International Maritime Organization (IMO) and the United States Coast Guard (USCG) have adopted ballast water management regulations that require, e.g., the installation of shipboard ballast water management systems (BWMS). Rapid and simple analytical methods are needed to monitor whether ballast water disinfection ensures compliance with the discharge standards. In this study laboratory and full scale land-based testing was used to investigate the suitability of an adenosine triphosphate (ATP) assay for quantifying living organisms (≥ 10 and < 50 μm minimum dimension) in ballast water. In laboratory experiments the ATP assay was highly sensitive, with a detection limit of < 5 cells 0.1 mL- 1. Diatom species (Chaetoceros simplex and Skeletonema costatum) had low ATP concentrations compared with dinoflagellate, Raphidophyceae, and Chrysophyceae species. This was because of differences in cell volume, as the ATP concentration increased exponentially with increasing cell volume. Using a regression model between ATP concentration and cell volume, an estimated the pass and fail ATP concentration in this study (788-98,610 pg mL- 1) was developed for the discharge of ballast water. In land-based testing the ATP assay also showed a good correlation with the presence of living natural plankton cells in control samples, but the ATP concentration (137 pg mL- 1) was much lower than the ATP guideline. The low ATP concentration in natural plankton cells may reflect a decline in their biological activity because of extended exposure to dark conditions. Although our results need further validation, the ATP assay is a suitable tool for monitoring compliance of ballast water treatment.

46 CFR 162.060-14 - Information requirements for the ballast water management system (BWMS) application.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 6 2012-10-01 2012-10-01 false Information requirements for the ballast water management system (BWMS) application. 162.060-14 Section 162.060-14 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) EQUIPMENT, CONSTRUCTION, AND MATERIALS: SPECIFICATIONS AND APPROVAL ENGINEERING EQUIPMENT Ballast Water Management Systems §...

Approaches to setting organism-based ballast water discharge standards

USGS Publications Warehouse

Lee, Henry; Reusser, Deborah A.; Frazier, Melanie

2013-01-01

As a vector by which foreign species invade coastal and freshwater waterbodies, ballast water discharge from ships is recognized as a major environmental threat. The International Maritime Organization (IMO) drafted an international treaty establishing ballast water discharge standards based on the number of viable organisms per volume of ballast discharge for different organism size classes. Concerns that the IMO standards are not sufficiently protective have initiated several state and national efforts in the United States to develop more stringent standards. We evaluated seven approaches to establishing discharge standards for the >50-μm size class: (1) expert opinion/management consensus, (2) zero detectable living organisms, (3) natural invasion rates, (4) reaction–diffusion models, (5) population viability analysis (PVA) models, (6) per capita invasion probabilities (PCIP), and (7) experimental studies. Because of the difficulty in synthesizing scientific knowledge in an unbiased and transparent fashion, we recommend the use of quantitative models instead of expert opinion. The actual organism concentration associated with a “zero detectable organisms” standard is defined by the statistical rigor of its monitoring program; thus it is not clear whether such a standard is as stringent as other standards. For several reasons, the natural invasion rate, reaction–diffusion, and experimental approaches are not considered suitable for generating discharge standards. PVA models can be used to predict the likelihood of establishment of introduced species but are limited by a lack of population vital rates for species characteristic of ballast water discharges. Until such rates become available, PVA models are better suited to evaluate relative efficiency of proposed standards rather than predicting probabilities of invasion. The PCIP approach, which is based on historical invasion rates at a regional scale, appears to circumvent many of the indicated problems

Comparative feasibility study on retrofitting ballast water treatment system for a bulk carrier.

PubMed

Jee, Jaehoon; Lee, Sangick

2017-06-30

Use of ballast water in ships causes harmful effects on marine environment accompanied by economic loss and negative impact on ecosystem and human health. To solve these problems, the international convention on ballast water management will take into force in September 2017. In this study, a comprehensive feasibility of retrofitting the ballast water treatment system for an ocean-going bulk carrier was conducted. The technologies involved, installation and operational aspects of direct flow and side stream electrolysis, UV, and ozone type BWTS are described in detail. The principal concept of each BWTS is explained and probable arrangements of retrofitting in engine room are suggested. The cost analysis is carried out for retrofitting 4 types of BWTS onboard the target ship by examining each processes of installation and operation. Copyright © 2017 Elsevier Ltd. All rights reserved.

Effects of ocean acidification on the ballast of surface aggregates sinking through the twilight zone.

PubMed

de Jesus Mendes, Pedro A; Thomsen, Laurenz

2012-01-01

The dissolution of CaCO(3) is one of the ways ocean acidification can, potentially, greatly affect the ballast of aggregates. A diminution of the ballast could reduce the settling speed of aggregates, resulting in a change in the carbon flux to the deep sea. This would mean lower amounts of more refractory organic matter reaching the ocean floor. This work aimed to determine the effect of ocean acidification on the ballast of sinking surface aggregates. Our hypothesis was that the decrease of pH will increase the dissolution of particulate inorganic carbon ballasting the aggregates, consequently reducing their settling velocity and increasing their residence time in the upper twilight zone. Using a new methodology for simulation of aggregate settling, our results suggest that future pCO(2) conditions can significantly change the ballast composition of sinking aggregates. The change in aggregate composition had an effect on the size distribution of the aggregates, with a shift to smaller aggregates. A change also occurred in the settling velocity of the particles, which would lead to a higher residence time in the water column, where they could be continuously degraded. In the environment, such an effect would result in a reduction of the carbon flux to the deep-sea. This reduction would impact those benthic communities, which rely on the vertical flow of carbon as primary source of energy.

Modeling the distribution of colonial species to improve estimation of plankton concentration in ballast water

NASA Astrophysics Data System (ADS)

Rajakaruna, Harshana; VandenByllaardt, Julie; Kydd, Jocelyn; Bailey, Sarah

2018-03-01

The International Maritime Organization (IMO) has set limits on allowable plankton concentrations in ballast water discharge to minimize aquatic invasions globally. Previous guidance on ballast water sampling and compliance decision thresholds was based on the assumption that probability distributions of plankton are Poisson when spatially homogenous, or negative binomial when heterogeneous. We propose a hierarchical probability model, which incorporates distributions at the level of particles (i.e., discrete individuals plus colonies per unit volume) and also within particles (i.e., individuals per particle) to estimate the average plankton concentration in ballast water. We examined the performance of the models using data for plankton in the size class ≥ 10 μm and < 50 μm, collected from five different depths of a ballast tank of a commercial ship in three independent surveys. We show that the data fit to the negative binomial and the hierarchical probability models equally well, with both models performing better than the Poisson model at the scale of our sampling. The hierarchical probability model, which accounts for both the individuals and the colonies in a sample, reduces the uncertainty associated with the concentration estimation, and improves the power of rejecting the decision on ship's compliance when a ship does not truly comply with the standard. We show examples of how to test ballast water compliance using the above models.

PERFORMANCE VERIFICATION OF SHIP BALLAST WATER TREATMENT TECHNOLOGIES

EPA Science Inventory

Ships use ballast water to provide stability during voyages and during loading and unloading operations. Water is taken on at one port when cargo is unloaded and usually discharged at another port when the ship receives cargo. Because sediments and/or organisms ranging in size ...

3D Finite Element Analysis of Some Structural Modified PC Sleeper with the Vibration Characteristics between Sleeper and Ballast

NASA Astrophysics Data System (ADS)

Sakai, Hirotaka; Urakawa, Fumihiro; Aikawa, Akira; Namura, Akira

The vibration of concrete sleepers is an important factor engendering track deterioration. In this paper, we created a three-dimensional finite element model to reproduce a prestressed concrete (PC) sleeper in detail, expressing influence of ballast layers with a 3D spring series and dampers to reproduce their vibration and dynamic characteristics. Determination of these parameters bases on the experimental modal analysis using an impact excitation technique for PC sleepers by adjusting the accelerance between the analytical results and experimental results. Furthermore, we compared the difference of these characteristics between normal sleepers and those with some structural modifications. Analytical results clarified that such means as sleeper width extension and increased sleeper thickness will influence the reduction of ballasted track vibration as improvements of PC sleepers.

33 CFR 157.10c - Segregated ballast tanks, crude oil washing systems, and dedicated clean ballast tanks for...

Code of Federal Regulations, 2011 CFR

2011-07-01

... to meet the draft and trim requirements in § 157.09(b); or (2) A crude oil washing system that meets... trim requirements in § 157.09(b); or (2) Dedicated clean ballast tanks that meet the design and... meet the draft and trim requirements in § 157.09(b). (d) If the arrangement of tanks on a vessel under...

33 CFR 157.10c - Segregated ballast tanks, crude oil washing systems, and dedicated clean ballast tanks for...

Code of Federal Regulations, 2010 CFR

2010-07-01

... to meet the draft and trim requirements in § 157.09(b); or (2) A crude oil washing system that meets... trim requirements in § 157.09(b); or (2) Dedicated clean ballast tanks that meet the design and... meet the draft and trim requirements in § 157.09(b). (d) If the arrangement of tanks on a vessel under...

Evaluating efficacy of filtration + UV-C radiation for ballast water treatment at different temperatures

NASA Astrophysics Data System (ADS)

Casas-Monroy, Oscar; Linley, Robert D.; Chan, Po-Shun; Kydd, Jocelyn; Vanden Byllaardt, Julie; Bailey, Sarah

2018-03-01

To prevent new ballast water-mediated introductions of aquatic nonindigenous species (NIS), many ships will soon use approved Ballast Water Management Systems (BWMS) to meet discharge standards for the maximum number of viable organisms in ballast water. Type approval testing of BWMS is typically conducted during warmer seasons when plankton concentrations are highest, despite the fact that ships operate globally year-round. Low temperatures encountered in polar and cool temperate climates, particularly during the winter season, may impact treatment efficacy through changes in plankton community composition, biological metabolic rates or chemical reaction rates. Filtration + UV irradiance is one of the most common ballast water treatment methods, but its effectiveness at low temperatures has not been assessed. The objective in this study was to examine the efficacy of filtration + UV-C irradiation treatment at low temperatures for removal or inactivation of phytoplankton and zooplankton populations during simulated ballast water treatment. Organisms from two size classes (≥ 10 to < 50 μm and ≥ 50 μm) were identified and enumerated using microscope and culture techniques. The response of organisms in both size categories to UV-C irradiation was evident across a range of temperatures (18 °C, 12 °C and 2 °C) as a significant decrease in concentration between controls and treated samples. Results indicate that filtration + UV-C irradiation will be effective at low temperatures, with few viable organisms ≥ 10 to < 50 μm recorded even 21 days following UV exposure (significantly lower than in the control treatment).

The efficiency of combined coagulant and ballast to remove harmful cyanobacterial blooms in a tropical shallow system.

PubMed

Miranda, Marcela; Noyma, Natália; Pacheco, Felipe S; de Magalhães, Leonardo; Pinto, Ernani; Santos, Suzan; Soares, Maria Fernanda A; Huszar, Vera L; Lürling, Miquel; Marinho, Marcelo M

2017-05-01

We tested the hypothesis that a combination of coagulant and ballast could be efficient for removal of positively buoyant harmful cyanobacteria in shallow tropical waterbodies, and will not promote the release of cyanotoxins. This laboratory study examined the efficacy of coagulants [polyaluminium chloride (PAC) and chitosan (made of shrimp shells)] alone, and combined with ballast (lanthanum modified bentonite, red soil or gravel) to remove the natural populations of cyanobacteria collected from a shallow eutrophic urban reservoir with alternating blooms of Cylindrospermopsis and Microcystis. PAC combined with ballast was effective in settling blooms dominated by Microcystis or Cylindrospermopsis. Contrary to our expectation, chitosan combined with ballast was only effective in settling Cylindrospermopsis-dominated blooms at low pH, whereas at pH≥8 no effective flocculation and settling could be evoked. Chitosan also had a detrimental effect on Cylindrospermopsis causing the release of saxitoxins. In contrast, no detrimental effect on Microcystis was observed and all coagulant-ballast treatments were effective in not only settling the Microcystis dominated bloom, but also lowering dissolved microcystin concentrations. Our data show that the best procedure for biomass reduction also depends on the dominant species. Copyright © 2017 Elsevier B.V. All rights reserved.

Density matters: Approaches to settling ballast water discharge concentrations

EPA Science Inventory

A consensus has evolved that invasion risk increases with propagule pressure. However, translating this general principal into ecologically “acceptable” concentrations of organisms in ballast water has proven challenging. The treaty being promulgated by the International Maritime...

Inactivation of dinoflagellate Scripsiella trochoidea in synthetic ballast water by advanced oxidation processes.

PubMed

Yang, Zhishan; Jiang, Wenju; Zhang, Yi; Lim, T M

2015-01-01

Ship-borne ballast water contributes significantly to the transfer of non-indigenous species across aquatic environments. To reduce the risk of bio-invasion, ballast water should be treated before discharge. In this study, the efficiencies of several conventional and advanced oxidation processes were investigated for potential ballast water treatment, using a marine dinoflagellate species, Scripsiella trochoidea, as the indicator organism. A stable and consistent culture was obtained and treated by ultraviolet (UV) light, ozone (O3), hydrogen peroxide (H2O2), and their various combinations. UV apparently inactivated the cells after only 10 s of irradiation, but subsequently photo-reactivation of the cells was observed for all methods involving UV. O3 exhibited 100% inactivation efficiency after 5 min treatment, while H2O2 only achieved maximum 80% inactivation in the same duration. Combined methods, e.g. UV/O3 and UV/H2O2, were found to inhibit photo-reactivation and improve treatment efficiency to some degree, indicating the effectiveness of using combined treatment processes. The total residual oxidant (TRO) levels of the methods were determined, and the results indicated that UV and O3 generated the lowest and highest TRO, respectively. The synergic effect of combined processes on TRO generation was found to be insignificant, and thus UV/O3 was recommended as a potentially suitable treatment process for ballast water.

10 CFR Appendix Q1 to Subpart B of... - Uniform Test Method for Measuring the Energy Consumption of Fluorescent Lamp Ballasts

Code of Federal Regulations, 2014 CFR

2014-01-01

... of Fluorescent Lamp Ballasts Q1 Appendix Q1 to Subpart B of Part 430 Energy DEPARTMENT OF ENERGY... of Fluorescent Lamp Ballasts Comply with Appendix Q1 beginning November 14, 2014. Prior to this date, all fluorescent lamp ballasts shall be tested using the provisions of Appendix Q. 1. Definitions 1.1...

10 CFR Appendix Q1 to Subpart B of... - Uniform Test Method for Measuring the Energy Consumption of Fluorescent Lamp Ballasts

Code of Federal Regulations, 2013 CFR

2013-01-01

... of Fluorescent Lamp Ballasts Q1 Appendix Q1 to Subpart B of Part 430 Energy DEPARTMENT OF ENERGY... of Fluorescent Lamp Ballasts Comply with Appendix Q1 beginning November 14, 2014. Prior to this date, all fluorescent lamp ballasts shall be tested using the provisions of Appendix Q. 1. Definitions 1.1...

Occurrence of Vibrio species, beta-lactam resistant Vibrio species, and indicator bacteria in ballast and port waters of a tropical harbor.

PubMed

Ng, Charmaine; Goh, Shin Giek; Saeidi, Nazanin; Gerhard, William A; Gunsch, Claudia K; Gin, Karina Yew Hoong

2018-01-01

Ballast water discharges are potential sources for the spread of invasive and pathogenic aquatic organisms. Ballast waters from six ships docked in the Port of Singapore were tested to determine if indictor organisms fell within proposed standards for ballast water discharge according to regulation D-2 of the Ballast Water Management Convention (BWMC) guidelines. Vibrio species were cultured on media supplemented with beta-lactam antibiotics to determine the presence of antibiotic resistant Vibrio species in the ballast waters of these vessels. Indicator organisms were quantified using culture media Colilert-18 and Enterolert in ballast waters of six ships docked in a tropical harbor, with uptake from different geographical locations. Of the six ships, one had ballast water originating from the Persian Gulf, another from the East China Sea, and four from the South China Sea. Two of the six ships which carried ballast waters from the East China Sea and the South China Sea did not meet the D-2 stipulated requirements of the Ballast Water Management Convention for indicator organisms with Enterococci values more than three times higher than the acceptable limit of <100CFU/100mL. Using the most-probable-number-PCR (MPN-PCR) method for Vibrio species detection, non-toxigenic species of V. cholerae (2 MPN/100mL), Vibrio vulnificus (>110 MPN/100mL), and Vibrio parahaemolyticus (2 to >110 MPN/100mL) were detected in at least one of six ballast water samples. Using thiosulfate-citrate-bile salts-sucrose agar (TCBS) supplemented with beta-lactam antibiotics (meropenem, ceftazidime), 11 different Vibrio species, exhibiting resistance to beta-lactam antibiotics were isolated; with Vibrio campbellii (44%) and Vibrio alginolyticus (15%) the most detected antibiotic resistant Vibrio species. A practical approach of prioritized screening of high-risk vessels should be conducted to ensure that the water quality meets D-2 standards prior to discharge. Copyright © 2017 Elsevier B

10 CFR Appendix Q1 to Subpart B of... - Uniform Test Method for Measuring the Energy Consumption of Fluorescent Lamp Ballasts

Code of Federal Regulations, 2012 CFR

2012-01-01

... of Fluorescent Lamp Ballasts Q1 Appendix Q1 to Subpart B of Part 430 Energy DEPARTMENT OF ENERGY... of Fluorescent Lamp Ballasts 1. Definitions 1.1. AC control signal means an alternating current (AC... functions. 1.3. Cathode heating refers to power delivered to the lamp by the ballast for the purpose of...

Disinfection by-products in ballast water treatment: an evaluation of regulatory data.

PubMed

Werschkun, Barbara; Sommer, Yasmin; Banerji, Sangeeta

2012-10-15

To reduce the global spread of invasive aquatic species, international regulations will soon require reductions of the number of organisms in ballast water discharged by ships. For this purpose, ballast water treatment systems were developed and approved by an international procedure. These systems rely on established water treatment principles which, to different degrees, have been proven to generate disinfection by-products with hazardous properties but have only scarcely been investigated in marine environments. Our study evaluates the publicly available documentation about approved ballast water treatment systems with regard to by-product formation. The most commonly employed methods are chlorination, ozonation, and ultraviolet (UV) irradiation. Chlorination systems generate trihalomethanes, halogenated acetic acids, and bromate in substantially larger quantities than reported for other areas of application. Levels are highest in brackish water, and brominated species predominate, in particular bromoform and dibromoacetic acid. Ozonation, which is less frequently utilized, produces bromoform in lower concentrations but forms higher levels of bromate, both of which were effectively reduced by active carbon treatment. In systems based on UV radiation, medium pressure lamps are employed as well as UV-induced advanced oxidation. For all UV systems, by-product formation is reported only occasionally. The most notable observations were small increases in nitrite, hydrogen peroxide, halogenated methanes and acetic acids. The assessment of by-product formation during ballast water treatment is limited by the lacking completeness and quality of available information. This concerns the extent and statistical characterisation of chemical analysis as well as the documentation of the test water parameters. Copyright © 2012 Elsevier Ltd. All rights reserved.

A Study of Ballast Water Treatment Using Engine Waste Heat

NASA Astrophysics Data System (ADS)

Balaji, Rajoo; Yaakob, Omar; Koh, Kho King; Adnan, Faizul Amri bin; Ismail, Nasrudin bin; Ahmad, Badruzzaman bin; Ismail, Mohd Arif bin

2018-05-01

Heat treatment of ballast water using engine waste heat can be an advantageous option complementing any proven technology. A treatment system was envisaged based on the ballast system of an existing, operational crude carrier. It was found that the available waste heat could raise the temperatures by 25 °C and voyage time requirements were found to be considerable between 7 and 12 days to heat the high volumes of ballast water. Further, a heat recovery of 14-33% of input energies from exhaust gases was recorded while using a test rig arrangement representing a shipboard arrangement. With laboratory level tests at temperature ranges of around 55-75 °C, almost complete species mortalities for representative phytoplankton, zooplankton and bacteria were observed while the time for exposure varied from 15 to 60 s. Based on the heat availability analyses for harvesting heat from the engine exhaust gases(vessel and test rig), heat exchanger designs were developed and optimized using Lagrangian method applying Bell-Delaware approaches. Heat exchanger designs were developed to suit test rig engines also. Based on these designs, heat exchanger and other equipment were procured and erected. The species' mortalities were tested in this mini-scale arrangement resembling the shipboard arrangement. The mortalities realized were > 95% with heat from jacket fresh water and exhaust gases alone. The viability of the system was thus validated.

49 CFR 1242.15 - Roadway, tunnels and subways, bridges and culverts, ties, rails, other track material, ballast...

Code of Federal Regulations, 2012 CFR

2012-10-01

... 49 Transportation 9 2012-10-01 2012-10-01 false Roadway, tunnels and subways, bridges and culverts, ties, rails, other track material, ballast, track laying and surfacing, and road property damaged... culverts, ties, rails, other track material, ballast, track laying and surfacing, and road property damaged...

49 CFR 1242.15 - Roadway, tunnels and subways, bridges and culverts, ties, rails, other track material, ballast...

Code of Federal Regulations, 2011 CFR

2011-10-01

... 49 Transportation 9 2011-10-01 2011-10-01 false Roadway, tunnels and subways, bridges and culverts, ties, rails, other track material, ballast, track laying and surfacing, and road property damaged... culverts, ties, rails, other track material, ballast, track laying and surfacing, and road property damaged...

49 CFR 1242.15 - Roadway, tunnels and subways, bridges and culverts, ties, rails, other track material, ballast...

Code of Federal Regulations, 2013 CFR

2013-10-01

... 49 Transportation 9 2013-10-01 2013-10-01 false Roadway, tunnels and subways, bridges and culverts, ties, rails, other track material, ballast, track laying and surfacing, and road property damaged... culverts, ties, rails, other track material, ballast, track laying and surfacing, and road property damaged...

49 CFR 1242.15 - Roadway, tunnels and subways, bridges and culverts, ties, rails, other track material, ballast...

Code of Federal Regulations, 2014 CFR

2014-10-01

... 49 Transportation 9 2014-10-01 2014-10-01 false Roadway, tunnels and subways, bridges and culverts, ties, rails, other track material, ballast, track laying and surfacing, and road property damaged... culverts, ties, rails, other track material, ballast, track laying and surfacing, and road property damaged...

10 CFR 431.324 - Uniform test method for the measurement of energy efficiency of metal halide ballasts.

Code of Federal Regulations, 2010 CFR

2010-01-01

... efficiency of metal halide ballasts. 431.324 Section 431.324 Energy DEPARTMENT OF ENERGY ENERGY CONSERVATION ENERGY EFFICIENCY PROGRAM FOR CERTAIN COMMERCIAL AND INDUSTRIAL EQUIPMENT Metal Halide Lamp Ballasts and Fixtures Test Procedures § 431.324 Uniform test method for the measurement of energy efficiency of metal...

A Laboratory Study Investigating the Feasibility of Applying Calcite-Type Coatings to Segregated Ballast Tanks

DTIC Science & Technology

1981-08-01

A LABORATORY STUDY INVESTIGATIING THE FEASIBILITY OF APPLYING CALCITE -TYPE COATINGS TO SEGREGATED BALLAST TANKS AUGUST, 1981 Prepared by: Ocean City...Laboratory Study Investigating The Feasibility of Applying Calcite -Type Coatings to Segregated Ballast Tanks 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c...Executive Summary List of Figures I. Conclusions II. Introduction III. Background-The Development and Use of Calcite -Type Coatings IV. Experimental

Hydroxide stabilization as a new tool for ballast disinfection: Efficacy of treatment on zooplankton

USGS Publications Warehouse

Moffitt, Christine M.; Watten, Barnaby J.; Barenburg, Amber; Henquinet, Jeffrey

2015-01-01

Effective and economical tools are needed for treating ship ballast to meet new regulatory requirements designed to reduce the introduction of invasive aquatic species from ship traffic. We tested the efficacy of hydroxide stabilization as a ballast disinfection tool in replicated, sequential field trials on board the M/V Ranger III in waters of Lake Superior. Ballast water was introduced into each of four identical 1,320 L stainless steel tanks during a simulated ballasting operation. Two tanks were treated with NaOH to elevate the pH to 11.7 and the remaining two tanks were held as controls without pH alteration. After retention on board for 14–18 h, CO2-rich gas recovered from one of two diesel propulsion engines was sparged into tanks treated with NaOH for 2 h to force conversion of NaOH ultimately to sodium bicarbonate, thereby lowering pH to about 7.1. Prior to gas sparging, the engine exhaust was treated by a unique catalytic converter/wet scrubber process train to remove unwanted combustion byproducts and to provide cooling. The contents of each tank were then drained and filtered through 35-µm mesh plankton nets to collect all zooplankton. The composition and relative survival of zooplankton in each tank were evaluated by microscopy. Zooplankton populations were dominated by rotifers, but copepods and cladocerans were also observed. Hydroxide stabilization was 100% effective in killing all zooplankton present at the start of the tests. Our results suggest hydroxide stabilization has potential to be an effective and practical tool to disinfect ship ballast. Further, using CO2 released from the ship engine reduces emissions and the neutralized by product, sodium bicarbonate, can have beneficial impacts on the aquatic environment.

Catch me if you can: Comparing ballast water sampling skids to traditional net sampling

NASA Astrophysics Data System (ADS)

Bradie, Johanna; Gianoli, Claudio; Linley, Robert Dallas; Schillak, Lothar; Schneider, Gerd; Stehouwer, Peter; Bailey, Sarah

2018-03-01

With the recent ratification of the International Convention for the Control and Management of Ships' Ballast Water and Sediments, 2004, it will soon be necessary to assess ships for compliance with ballast water discharge standards. Sampling skids that allow the efficient collection of ballast water samples in a compact space have been developed for this purpose. We ran 22 trials on board the RV Meteor from June 4-15, 2015 to evaluate the performance of three ballast water sampling devices (traditional plankton net, Triton sampling skid, SGS sampling skid) for three organism size classes: ≥ 50 μm, ≥ 10 μm to < 50 μm, and < 10 μm. Natural sea water was run through the ballast water system and untreated samples were collected using paired sampling devices. Collected samples were analyzed in parallel by multiple analysts using several different analytic methods to quantify organism concentrations. To determine whether there were differences in the number of viable organisms collected across sampling devices, results were standardized and statistically treated to filter out other sources of variability, resulting in an outcome variable representing the mean difference in measurements that can be attributed to sampling devices. These results were tested for significance using pairwise Tukey contrasts. Differences in organism concentrations were found in 50% of comparisons between sampling skids and the plankton net for ≥ 50 μm, and ≥ 10 μm to < 50 μm size classes, with net samples containing either higher or lower densities. There were no differences for < 10 μm organisms. Future work will be required to explicitly examine the potential effects of flow velocity, sampling duration, sampled volume, and organism concentrations on sampling device performance.

33 CFR 401.30 - Ballast water and trim.

Code of Federal Regulations, 2013 CFR

2013-07-01

... flushing is defined as the addition of mid-ocean water to ballast water tanks: The mixing of the flushwater..., such that the resultant residual water remaining in the tank has as high salinity as possible, and is at least 30 parts per thousand (ppt). The vessel shall take on as much mid-ocean water into each tank...

33 CFR 401.30 - Ballast water and trim.

Code of Federal Regulations, 2012 CFR

2012-07-01

... flushing is defined as the addition of mid-ocean water to ballast water tanks: The mixing of the flushwater..., such that the resultant residual water remaining in the tank has as high salinity as possible, and is at least 30 parts per thousand (ppt). The vessel shall take on as much mid-ocean water into each tank...

4. AN IMAGE, LOOKING NORTH WEST, OF THE TRACK, BALLAST ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

4. AN IMAGE, LOOKING NORTH WEST, OF THE TRACK, BALLAST AND CONCRETE BALUSTRADES, SHOWING HOW THE BRIDGE WAS DESIGNED TO TAKE TWO SETS OF TRACK. - Vandalia Railroad Bridge, Spanning U.S. Route 40, Indianapolis, Marion County, IN

Combining Ballast Water Exchange and Treatment To Maximize Prevention of Species Introductions to Freshwater Ecosystems.

PubMed

Briski, Elizabeta; Gollasch, Stephan; David, Matej; Linley, R Dallas; Casas-Monroy, Oscar; Rajakaruna, Harshana; Bailey, Sarah A

2015-08-18

The most effective way to manage species transfers is to prevent their introduction via vector regulation. Soon, international ships will be required to meet numeric ballast discharge standards using ballast water treatment (BWT) systems, and ballast water exchange (BWE), currently required by several countries, will be phased out. However, there are concerns that BWT systems may not function reliably in fresh and/or turbid water. A land-based evaluation of simulated "BWE plus BWT" versus "BWT alone" demonstrated potential benefits of combining BWE with BWT for protection of freshwater ecosystems. We conducted ship-based testing to compare the efficacy of "BWE plus BWT" versus "BWT alone" on voyages starting with freshwater ballast. We tested the hypotheses that there is an additional effect of "BWE plus BWT" compared to "BWT alone" on the reduction of plankton, and that taxa remaining after "BWE plus BWT" will be marine (low risk for establishment at freshwater recipient ports). Our study found that BWE has significant additional effect on the reduction of plankton, and this effect increases with initial abundance. As per expectations, "BWT alone" tanks contained higher risk freshwater or euryhaline taxa at discharge, while "BWE plus BWT" tanks contained mostly lower risk marine taxa unlikely to survive in recipient freshwater ecosystems.

Generic Protocol for the Verification of Ballast Water Treatment Technology

EPA Science Inventory

In anticipation of the need to address performance verification and subsequent approval of new and innovative ballast water treatment technologies for shipboard installation, the U.S Coast Guard and the Environmental Protection Agency‘s Environmental Technology Verification Progr...

Diversity of bacteria in ships ballast water as revealed by next generation DNA sequencing.

PubMed

Brinkmeyer, Robin

2016-06-15

The bacterial diversity in ballast water from five general cargo ships calling at the Port of Houston was determined with ion semiconductor DNA sequencing (Ion Torrent PGM) of PCR amplified 16S rRNA genes. Phylogenetic analysis revealed that the composition of bacteria in ballast water did not resemble that of typical marine habitats or even open ocean waters where BWEs occur. The predominant group of bacteria in ships conducting BWEs was the Roseobacter clade within the Alphaproteobacteria. In contrast, Gammaproteobacteria were predominant in the ship that did not conduct a BWE. All the ships contained human, fish, and terrestrial plant pathogens as well as bacteria indicative of fecal or activated sludge contamination. Most of the 60 pathogens had not been detected in ballast water previously. Among these were the human pathogens Corynebacterium diptheriae and several Legionella species and the fish pathogens Francisella piscicida and Piscirickettsia salmonis. Copyright © 2016 Elsevier Ltd. All rights reserved.

46 CFR 56.50-50 - Bilge and ballast piping.

Code of Federal Regulations, 2010 CFR

2010-10-01

... or in the boiler or machinery space, including spaces in which oil settling tanks or oil pumping... pumping from and draining any watertight compartment except for ballast, oil and water tanks which have... the suction pipes. Efficient means shall be provided for draining water from all tank tops, other...

A New Treatment Strategy for Inactivating Algae in Ballast Water Based on Multi-Trial Injections of Chlorine

PubMed Central

Sun, Jinyang; Wang, Junsheng; Pan, Xinxiang; Yuan, Haichao

2015-01-01

Ships’ ballast water can carry aquatic organisms into foreign ecosystems. In our previous studies, a concept using ion exchange membrane electrolysis to treat ballast water has been proven. In addition to other substantial approaches, a new strategy for inactivating algae is proposed based on the developed ballast water treatment system. In the new strategy, the means of multi-trial injection with small doses of electrolytic products is applied for inactivating algae. To demonstrate the performance of the new strategy, contrast experiments between new strategies and routine processes were conducted. Four algae species including Chlorella vulgaris, Platymonas subcordiformis, Prorocentrum micans and Karenia mikimotoi were chosen as samples. The different experimental parameters are studied including the injection times and doses of electrolytic products. Compared with the conventional one trial injection method, mortality rate time (MRT) and available chlorine concentration can be saved up to about 84% and 40%, respectively, under the application of the new strategy. The proposed new approach has great potential in practical ballast water treatment. Furthermore, the strategy is also helpful for deep insight of mechanism of algal tolerance. PMID:26068239

A Spatial Modeling Approach to Predicting the Secondary Spread of Invasive Species Due to Ballast Water Discharge

PubMed Central

Sieracki, Jennifer L.; Bossenbroek, Jonathan M.; Chadderton, W. Lindsay

2014-01-01

Ballast water in ships is an important contributor to the secondary spread of invasive species in the Laurentian Great Lakes. Here, we use a model previously created to determine the role ballast water management has played in the secondary spread of viral hemorrhagic septicemia virus (VHSV) to identify the future spread of one current and two potential invasive species in the Great Lakes, the Eurasian Ruffe (Gymnocephalus cernuus), killer shrimp (Dikerogammarus villosus), and golden mussel (Limnoperna fortunei), respectively. Model predictions for Eurasian Ruffe have been used to direct surveillance efforts within the Great Lakes and DNA evidence of ruffe presence was recently reported from one of three high risk port localities identified by our model. Predictions made for killer shrimp and golden mussel suggest that these two species have the potential to become rapidly widespread if introduced to the Great Lakes, reinforcing the need for proactive ballast water management. The model used here is flexible enough to be applied to any species capable of being spread by ballast water in marine or freshwater ecosystems. PMID:25470822

33 CFR Appendix D to Part 157 - Example of a Procedure for Dedicated Clean Ballast Tanks Operations

Code of Federal Regulations, 2010 CFR

2010-07-01

... Dedicated Clean Ballast Tanks Operations D Appendix D to Part 157 Navigation and Navigable Waters COAST... ENVIRONMENT RELATING TO TANK VESSELS CARRYING OIL IN BULK Pt. 157, App. D Appendix D to Part 157—Example of a.... (3) Ensure that all valves in the dedicated clean ballast tanks are closed. (d) Before arrival at the...

Novel Electrokinetic Microfluidic Detector for Evaluating Effectiveness of Microalgae Disinfection in Ship Ballast Water

PubMed Central

Maw, Myint Myint; Wang, Junsheng; Li, Fabo; Jiang, Jinhu; Song, Younan; Pan, Xinxiang

2015-01-01

Ship ballast water treatment methods face many technical challenges. The effectiveness of every treatment method usually is evaluated by using large scale equipment and a large volume of samples, which involves time-consuming, laborious, and complex operations. This paper reports the development of a novel, simple and fast platform of methodology in evaluating the efficiency and the best parameters for ballast water treatment systems, particularly in chemical disinfection. In this study, a microfluidic chip with six sample wells and a waste well was designed, where sample transportation was controlled by electrokinetic flow. The performance of this microfluidic platform was evaluated by detecting the disinfection of Dunaliella salina (D. salina) algae in ballast water treated by sodium hypochlorite (NaClO) solution. Light-induced chlorophyll fluorescence (LICF) intensity was used to determine the viability of microalgae cells in the system, which can be operated automatically with the dimension of the detector as small as 50 mm × 24 mm × 5 mm. The 40 µL volume of sample solution was used for each treatment condition test and the validity of detection can be accomplished within about five min. The results show that the viability of microalgae cells under different treatment conditions can be determined accurately and further optimal treatment conditions including concentrations of NaClO and treatment time can also be obtained. These results can provide accurate evaluation and optimal parameters for ballast water treatment methods. PMID:26516836

Chamber study of PCBemissions from caulking materials and light ballasts

EPA Science Inventory

The emissions of polychlorinated biphenyl (PCB) congeners from 13 caulk samples were tested in a micro-chamber system. Twelve samples were from PCB-contaminated buildings and one was prepared in the laboratory. Nineteen light ballasts collected from buildings that represent 13 di...

33 CFR 157.160 - Tanks: Ballasting and crude oil washing.

Code of Federal Regulations, 2010 CFR

2010-07-01

... CARRYING OIL IN BULK Crude Oil Washing (COW) System on Tank Vessels Cow Operations § 157.160 Tanks... vessel having a COW system under § 157.10a(a)(2) or § 157.10c(b)(2) shall ensure that— (1) Ballast water...

Heat-Transfer in Reflector-type Self-Ballasted Compact Fluorescent Lamps

NASA Astrophysics Data System (ADS)

Yasuda, Takeo; Toda, Masahiro; Matsumoto, Shinichiro; Takahara, Yuichiro

Self-ballasted compact fluorescent lamps (SBCFL) are widely used to replace incandescent lamps (IL) to save energy. We studied the heat-transfer phenomena of SBCFLs with outer envelopes by measuring the temperatures of the lamp parts, the power consumption, and the luminous output, and by calculating the energy balance. The methods applied were heat-transfer network analysis and computational fluid dynamics (CFD) using FLUENT® software. The heat loss increased in reflector-type SBCFLs as compared to SBCFLs with non-reflective outer envelopes, and was estimated at about 3 W when the total lamp power was 22 W. This results in a temperature rise of 20 K in the plastic holder, and a maximum rise of 10 K at the electronic components on the circuit board. Accordingly, we have developed a 12 W reflector-type SBCFL, which replaces a 60 W incandescent, not a 22 W SBCFL replacing a 100 W incandescent R-lamp, due to the importance of thermal reliability.

A Comparison of Microbial Water Quality and Diversity for Ballast and Tropical Harbor Waters

PubMed Central

Goh, Shin Giek; Liang, Liang; Kim, Yiseul; Rose, Joan B.; Yew-Hoong, Karina Gin

2015-01-01

Indicator organisms and antibiotic resistance were used as a proxy to measure microbial water quality of ballast tanks of ships, and surface waters in a tropical harbor. The survival of marine bacteria in ballast tanks appeared to diminish over longer water retention time, with a reduction of cell viability observed after a week based on heterotrophic plate counts. Pyrosequencing of 16S rRNA genes showed distinct differences in microbial composition of ballast and harbor waters. The harbor waters had a higher abundance of operational taxonomic units (OTUs) assigned to Cyanobacteria (Synechococcus spp.) and α-proteobacteria (SAR11 members), while marine hydrocarbon degraders such as γ-proteobacteria (Ocenspirillaes spp., Thiotrchales spp.) and Bacteroidetes (Flavobacteriales spp.) dominated the ballast water samples. Screening of indicator organisms found Escherichia coli (E. coli), Enterococcus and Pseudomonas aeruginosa (P. aeruginosa) in two or more of the ballast and harbor water samples tested. Vibrio spp. and Salmonella spp. were detected exclusively in harbor water samples. Using quantitative PCR (qPCR), we screened for 13 antibiotic resistant gene (ARG) targets and found higher abundances of sul1 (4.13–3.44 x 102 copies/mL), dfrA (0.77–1.80 x10 copies/mL) and cfr (2.00–5.21 copies/mL) genes compared to the other ARG targets selected for this survey. These genes encode for resistance to sulfonamides, trimethoprim and chloramphenicol-florfenicol antibiotics, which are also known to persist in sediments of aquaculture farms and coastal environments. Among the ARGs screened, we found significant correlations (P<0.05) between ereA, ermG, cfr and tetO genes to one or more of the indicator organisms detected in this study, which may suggest that these members contribute to the environmental resistome. This study provides a baseline water quality survey, quantitatively assessing indicators of antibiotic resistance, potentially pathogenic organisms and a

A Comparison of Microbial Water Quality and Diversity for Ballast and Tropical Harbor Waters.

PubMed

Ng, Charmaine; Le, Thai-Hoang; Goh, Shin Giek; Liang, Liang; Kim, Yiseul; Rose, Joan B; Yew-Hoong, Karina Gin

2015-01-01

Indicator organisms and antibiotic resistance were used as a proxy to measure microbial water quality of ballast tanks of ships, and surface waters in a tropical harbor. The survival of marine bacteria in ballast tanks appeared to diminish over longer water retention time, with a reduction of cell viability observed after a week based on heterotrophic plate counts. Pyrosequencing of 16S rRNA genes showed distinct differences in microbial composition of ballast and harbor waters. The harbor waters had a higher abundance of operational taxonomic units (OTUs) assigned to Cyanobacteria (Synechococcus spp.) and α-proteobacteria (SAR11 members), while marine hydrocarbon degraders such as γ-proteobacteria (Ocenspirillaes spp., Thiotrchales spp.) and Bacteroidetes (Flavobacteriales spp.) dominated the ballast water samples. Screening of indicator organisms found Escherichia coli (E. coli), Enterococcus and Pseudomonas aeruginosa (P. aeruginosa) in two or more of the ballast and harbor water samples tested. Vibrio spp. and Salmonella spp. were detected exclusively in harbor water samples. Using quantitative PCR (qPCR), we screened for 13 antibiotic resistant gene (ARG) targets and found higher abundances of sul1 (4.13-3.44 x 102 copies/mL), dfrA (0.77-1.80 x10 copies/mL) and cfr (2.00-5.21 copies/mL) genes compared to the other ARG targets selected for this survey. These genes encode for resistance to sulfonamides, trimethoprim and chloramphenicol-florfenicol antibiotics, which are also known to persist in sediments of aquaculture farms and coastal environments. Among the ARGs screened, we found significant correlations (P<0.05) between ereA, ermG, cfr and tetO genes to one or more of the indicator organisms detected in this study, which may suggest that these members contribute to the environmental resistome. This study provides a baseline water quality survey, quantitatively assessing indicators of antibiotic resistance, potentially pathogenic organisms and a broad

Counting at low concentrations: the statistical challenges of verifying ballast water discharge standards

USGS Publications Warehouse

Frazier, Melanie; Miller, A. Whitman; Lee, Henry; Reusser, Deborah A.

2013-01-01

Discharge from the ballast tanks of ships is one of the primary vectors of nonindigenous species in marine environments. To mitigate this environmental and economic threat, international, national, and state entities are establishing regulations to limit the concentration of living organisms that may be discharged from the ballast tanks of ships. The proposed discharge standards have ranged from zero detectable organisms to 3. If standard sampling methods are used, verifying whether ballast discharge complies with these stringent standards will be challenging due to the inherent stochasticity of sampling. Furthermore, at low concentrations, very large volumes of water must be sampled to find enough organisms to accurately estimate concentration. Despite these challenges, adequate sampling protocols comprise a critical aspect of establishing standards because they help define the actual risk level associated with a standard. A standard that appears very stringent may be effectively lax if it is paired with an inadequate sampling protocol. We describe some of the statistical issues associated with sampling at low concentrations to help regulators understand the uncertainties of sampling as well as to inform the development of sampling protocols that ensure discharge standards are adequately implemented.

Density matters: Approaches to settling ballast water discharge concentrations - 10/22

EPA Science Inventory

A consensus has evolved that invasion risk increases with propagule pressure. However, translating this general principal into ecologically “acceptable” concentrations of organisms in ballast water has proven challenging. The treaty being promulgated by the International Maritime...

Enhanced performance of crumb rubber filtration for ballast water treatment.

PubMed

Tang, Zhijian; Butkus, Michael A; Xie, Yuefeng F

2009-03-01

Waste-tire-derived crumb rubber was utilized as filter media to develop an efficient filter for ballast water treatment. In this study, the effects of coagulation, pressure filtration and dual-media (gravity) filtration on the performance of the crumb rubber filtration were investigated. The removal efficiencies of turbidity, phytoplankton and zooplankton, and head loss development were monitored during the filtration process. The addition of a coagulant enhanced the removal efficiencies of all targeted matter, but resulted in substantial increase of head loss. Pressure filtration increased filtration rates to 220 m(3)h(-1)m(-2) for 8-h operation and improved the zooplankton removal. Dual-media (crumb rubber/sand) gravity filtration also improved the removal efficiencies of phytoplankton and zooplankton over mono-media gravity crumb rubber filtration. However, these filtration techniques alone did not meet the criteria for removing indigenous organisms from ballast water. A combination of filtration and disinfection is suggested for future studies.

Compaction of Railway Ballast During Tamping Process: a Parametric Study

NASA Astrophysics Data System (ADS)

Saussine, G.; Azéma, E.; Perales, R.; Radjaï, F.

2009-06-01

We characterize an industrial process currently used on railway track: tamping operation. This process is employed in order to restore the geometry of railway track distorted by train traffics. The main goal is to compact the granular material under the sleepers supporting the railroad squeezing and vibrations. We focus on different phases of the tamping process, namely the penetration of tamping tines into the ballast and squeezing of ballast between tines. Our numerical simulations of three-dimensional discrete polyhedral grains allow us to investigate the influence of vibration frequency on the compaction level at the end of the process, the role of velocity of tamping tines during penetration phase and the mechanism of compaction of a confined granular layer under horizontal vibrations. For each tamping phase, an optimal frequency is proposed, and an analysis of the full process on the samples representing a portion of the railway track enables us to access the influence of various parameters required to optimize the process.

Is the aquatic environment sufficiently protected from chemicals discharged with treated ballast water from vessels worldwide? - A decadal environmental perspective and risk assessment.

PubMed

David, Matej; Linders, Jan; Gollasch, Stephan; David, Jan

2018-05-24

Ballast water managements systems (BWMS) installed on vessels may use active substances to inactivate or kill organisms in the ballast water. This paper provides new insights in this global issue - discharge of hazardous disinfection by-products with ballast water and related risk assessment for the environment. Considering the possible extent of this issue, the International Maritime Organization (IMO) engaged the Joint Group of Experts on the Scientific Aspects of Marine Environmental Protection (GESAMP)-Ballast Water Working Group (BWWG) to oversee the evaluation process of BWMS that make use of active substances to prevent negative effects. We analysed all BWMS that received IMO final approval over a decade until 2017 and provide an overview of active substances used for ballast water treatment and disinfection by-products in the discharged ballast water. A risk assessment was conducted using the GESAMP-BWWG methodology for two very different commercial ports (Koper, Slovenia and Hamburg, Germany). Some relevant chemicals (chloropicrin, monochloroacetic acid, and dibromoacetonitrile) and other chemicals (isocyanuric acid and sodium thiosulphate) reached levels of concern, indicating a risk for aquatic organisms after discharge of that ballast water. From this analysis, it became clear GESAMP-BWWG worst-case scenario assumptions do not fully account for the potential environmental risks. We provide recommendations how to make this risk assessment more robust, recommend further research, and urge for policy as well as regulatory responses. Copyright © 2018 Elsevier Ltd. All rights reserved.

Potential transfer of aquatic organisms via ballast water with a particular focus on harmful and non-indigenous species: A survey from Adriatic ports.

PubMed

Cabrini, M; Cerino, F; de Olazabal, A; Di Poi, E; Fabbro, C; Fornasaro, D; Goruppi, A; Flander-Putrle, V; Francé, J; Gollasch, S; Hure, M; Lipej, L; Lučić, D; Magaletti, E; Mozetič, P; Tinta, T; Tornambè, A; Turk, V; Uhan, J; David, M

2018-02-14

Ballast water discharges may cause negative impacts to aquatic ecosystems, human health and economic activities by the introduction of potentially harmful species. Fifty untreated ballast water tanks, ten in each port, were sampled in four Adriatic Italian ports and one Slovenian port. Salinity, temperature and fluorescence were measured on board. Faecal indicator bacteria (FIB), phyto- and zooplankton were qualitatively and quantitatively determined to identify the species assemblage arriving in ballast water. FIB exceeded the convention standard limits in 12% of the sampled tanks. Vibrio cholerae was not detected. The number of viable organisms in the size groups (minimum dimension) <50 and ≥10 μm and ≥50 μm resulted above the abundances required from the Ballast Water Management Convention in 55 and 86% of the samples, respectively. This is not surprising as unmanaged ballast waters were sampled. Some potentially toxic and non-indigenous species were observed in both phyto- and zooplankton assemblages. Copyright © 2018 Elsevier Ltd. All rights reserved.

Optimal approaches for inline sampling of organisms in ballast water: L-shaped vs. Straight sample probes

NASA Astrophysics Data System (ADS)

Wier, Timothy P.; Moser, Cameron S.; Grant, Jonathan F.; Riley, Scott C.; Robbins-Wamsley, Stephanie H.; First, Matthew R.; Drake, Lisa A.

2017-10-01

Both L-shaped ("L") and straight ("Straight") sample probes have been used to collect water samples from a main ballast line in land-based or shipboard verification testing of ballast water management systems (BWMS). A series of experiments was conducted to quantify and compare the sampling efficiencies of L and Straight sample probes. The findings from this research-that both L and Straight probes sample organisms with similar efficiencies-permit increased flexibility for positioning sample probes aboard ships.

10 CFR 429.54 - Metal halide lamp ballasts and fixtures.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 10 Energy 3 2014-01-01 2014-01-01 false Metal halide lamp ballasts and fixtures. 429.54 Section 429.54 Energy DEPARTMENT OF ENERGY ENERGY CONSERVATION CERTIFICATION, COMPLIANCE, AND ENFORCEMENT FOR... and tested to ensure that: (i) Any represented value of estimated energy efficiency calculated as the...

10 CFR 429.54 - Metal halide lamp ballasts and fixtures.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 10 Energy 3 2012-01-01 2012-01-01 false Metal halide lamp ballasts and fixtures. 429.54 Section 429.54 Energy DEPARTMENT OF ENERGY ENERGY CONSERVATION CERTIFICATION, COMPLIANCE, AND ENFORCEMENT FOR... and tested to ensure that: (i) Any represented value of estimated energy efficiency calculated as the...

10 CFR 429.54 - Metal halide lamp ballasts and fixtures.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 10 Energy 3 2013-01-01 2013-01-01 false Metal halide lamp ballasts and fixtures. 429.54 Section 429.54 Energy DEPARTMENT OF ENERGY ENERGY CONSERVATION CERTIFICATION, COMPLIANCE, AND ENFORCEMENT FOR... and tested to ensure that: (i) Any represented value of estimated energy efficiency calculated as the...

Nucleic acids-based tools for ballast water surveillance, monitoring, and research

EPA Science Inventory

Understanding the risks of biological invasion posed by ballast water—whether in the context of compliance testing, routine monitoring, or basic research—is fundamentally an exercise in biodiversity assessment, and as such should take advantage of the best tools avail...

10 CFR 431.322 - Definitions concerning metal halide lamp ballasts and fixtures.

Code of Federal Regulations, 2010 CFR

2010-01-01

... is produced by radiation of metal halides and their products of dissociation, possibly in combination... electromagnetic ballast that starts a pulse-start metal halide lamp with high voltage pulses, where lamps shall be...

33 CFR 151.2037 - If my vessel cannot conduct ballast water management practices because of its voyage and/or...

Code of Federal Regulations, 2010 CFR

2010-07-01

... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false If my vessel cannot conduct ballast water management practices because of its voyage and/or safety concerns, will I be prohibited from discharging ballast water? 151.2037 Section 151.2037 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED)...

33 CFR 151.2037 - If my vessel cannot conduct ballast water management practices because of its voyage and/or...

Code of Federal Regulations, 2011 CFR

2011-07-01

... 33 Navigation and Navigable Waters 2 2011-07-01 2011-07-01 false If my vessel cannot conduct ballast water management practices because of its voyage and/or safety concerns, will I be prohibited from discharging ballast water? 151.2037 Section 151.2037 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED)...

The ships' ballast water impact on the Black Sea marine environment

NASA Astrophysics Data System (ADS)

Acomi, Nicoleta; Acomi, Ovidiu

2015-04-01

Ships use ballast water to provide stability during voyages. This type of seawater loaded on board from one geographical area and discharged in very different port areas as ballasting practice, turned into a vector for spreading the non-native sea life species. The reduction and limitation of invasive species is a problem that the modern world addresses. Thus, the International Maritime Organization (IMO) developed the BWM 2004 Convention. Adopting international regulations influences the socio-economic sector and this is the reason why the ballast water, the subject of this paper, has been on the IMO Marine Environment Protection Committee's agenda for more than 10 years, while the Convention has not yet been ratified and enforced. Although the Black Sea was subject to incidents regarding the invasive species the Romanian Government, as member of the IMO, did not ratify the Convention. The Black Sea was the subject of four major incidents regarding the ships' ballast water. One of them refers to the North American Comb Jelly, native from the Eastern Seaboard of America, introduced in the Black, Azov and Caspian Seas and seriously affecting the Romanian coastal environment in the 1990's. This invasive species has negative impacts: it reproduces rapidly under favourable conditions, it feeds excessively on zooplankton, it depletes zooplankton stocks, altering the food web and the ecosystem functionality, and contributed significantly to the collapse of Black and Azov Sea fisheries in the 1990s, with massive economic and social impact. There are studies for identifying the invasive species for the Black sea, structured in a database for marine species - the Black Sea Red Data Book. For these invasive species, there have been identified and developed charts to emphasize their ways of migration into the Black Sea. This paper aims to analyse the marine traffic in Romanian ports, broken down according with seasons and types of vessels, and to assess its relationship with

Assessment of aggregate sources in Michigan for high speed railroad ballast.

DOT National Transportation Integrated Search

2014-01-01

MDOT purchased 135 miles of the Norfolk-Southern railroad in 2012 to upgrade for high speed rail travel : between Chicago and the Detroit area. An important part of the upgrade is to assess the current quality of : the ballast material and to determi...

Ballast Water Treatment, U.S. Great Lakes Bulk Carrier Engineering and Cost Study. Volume 1: Present Conditions

DTIC Science & Technology

2013-11-01

There are two U.S. cement plants (Charlevoix and Alpena ) that supply all U.S. ports on the lakes. Ballast Water Treatment, U.S. Great Lakes...Marquette, MI Brevort, MI Buffington, IN Alpena , MI Bay City, MI Cleveland, OH Ashtabula, OH Duluth, MN Munising, MI Charlevoix, MI Burns Harbor, IN...Manitowoc Pathfinder Calumet Alpena Total shown: 40,699,415 mt Total, all U.S. Vsls: 42,508,108 mt % ballast moved by top 5 vsls

Potential effects of LNG trade shift on transfer of ballast water and biota by ships.

PubMed

Holzer, Kimberly K; Muirhead, Jim R; Minton, Mark S; Carney, Katharine J; Miller, A Whitman; Ruiz, Gregory M

2017-02-15

As the US natural gas surplus grows, so does the prospect of establishing new trade partnerships with buyers abroad, a process that has major consequences for global ship movement and ballast water delivery. Since US annual imports of liquefied natural gas (LNG) peaked in 2004-2007, the country is rapidly transitioning from net importer to net exporter of LNG. Combining multiple datasets, we estimated changes in the associated flux of ships' ballast water to the US during 2015-2040, using existing scenarios for projected exports of domestic LNG by ships. Our analysis of the current market (2015) scenario predicts an approximate 90-fold annual increase in LNG-related ballast water discharge to the US by 2040 (42millionm 3 ), with the potential to be even greater under high oil prices. We also described changes in geographic connectivity related to trade direction. These findings highlight how 21 st century global energy markets could dramatically alter opportunities for seaborne introductions and invasions by nonnative species. Copyright © 2016 Elsevier B.V. All rights reserved.

Inactivation of invasive marine species in the process of conveying ballast water using OH based on a strong ionization discharge.

PubMed

Bai, Mindong; Zheng, Qilin; Tian, Yiping; Zhang, Zhitao; Chen, Cao; Cheng, Chao; Meng, Xiangying

2016-06-01

In this paper, invasive marine species in medium-salinity ballast water were inactivated using OH generated from a strong ionization discharge. The OH is determined by the concentration of oxygen active species combined with the effects of water jet cavitation. The results indicated that the OH concentration reached 7.62 μM, within 1 s, which is faster and higher than in conventional AOP methods. In a pilot-scale OH ballast water system with a capacity of 10 m(3)/h, algae were inactivated when CT value was 0.1 mg min/L with a contact time only 6 s. The viable and nonviable cells were determined using SYTOX Green nucleic acid stain and Flow cytometry. As a result, the OH treatment could be completed during the process of conveying the ballast water. In addition, the concentrations of relevant disinfection by-products (DBPs), such as trihalomethanes (THMs), haloacetic acids (HAAs), and bromate, were less than that required by the World Health Organization's drinking water standards, which suggest that the discharged ballast water posed no risks to the oceanic environment. Nevertheless, for conventional ozonation and electrolysis methods, the ballast water should be treated only in the treated tanks during the ship's voyage and form higher level DBPs. Copyright © 2016 Elsevier Ltd. All rights reserved.

Recolonization by heterotrophic bacteria after UV irradiation or ozonation of seawater; a simulation of ballast water treatment.

PubMed

Hess-Erga, Ole-Kristian; Blomvågnes-Bakke, Bente; Vadstein, Olav

2010-10-01

Transport of ballast water with ships represents a risk for introduction of foreign species. If ballast water is treated during uptake, there will be a recolonization of the ballast water by heterotrophic bacteria during transport. We investigated survival and succession of heterotrophic bacteria after disinfection of seawater in the laboratory, representing a model system of ballast water treatment and transport. The seawater was exposed to ultraviolet (UV) irradiation, ozone (2 doses) or no treatment, incubated for 16 days and examined with culture-dependent and -independent methods. The number of colony-forming units (CFU) was reduced below the detection level after disinfection with UV and high ozone dose (700 mV), and 1% of the initial level for the low ozone dose (400 mV). After less than 3 days, the CFU was back or above the starting point for the control, UV and low ozone treatment, whereas it took slightly more than 6 days for the high ozone treatment. Disinfection increased substrate availability and reduced cell densities. Lack of competition and predation induced the recolonization by opportunistic bacteria (r-strategists), with significant increase in bacterial numbers and a low diversity (based on DGGE band pattern). All cultures stabilized after the initial recolonization phase (except Oz700) where competition due to crowding and nutrient limitation favoured bacteria with high substrate affinity (K-strategists), resulting in higher species richness and diversity (based on DGGE band pattern). The bacterial community was significantly altered qualitatively and quantitatively and may have a higher potential as invaders in the recipient depending on disinfection method and the time of release. These results have implications for the treatment strategy used for ballast water. Copyright © 2010 Elsevier Ltd. All rights reserved.

Railway track geometry degradation due to differential settlement of ballast/subgrade - Numerical prediction by an iterative procedure

NASA Astrophysics Data System (ADS)

Nielsen, Jens C. O.; Li, Xin

2018-01-01

An iterative procedure for numerical prediction of long-term degradation of railway track geometry (longitudinal level) due to accumulated differential settlement of ballast/subgrade is presented. The procedure is based on a time-domain model of dynamic vehicle-track interaction to calculate the contact loads between sleepers and ballast in the short-term, which are then used in an empirical model to determine the settlement of ballast/subgrade below each sleeper in the long-term. The number of load cycles (wheel passages) accounted for in each iteration step is determined by an adaptive step length given by a maximum settlement increment. To reduce the computational effort for the simulations of dynamic vehicle-track interaction, complex-valued modal synthesis with a truncated modal set is applied for the linear subset of the discretely supported track model with non-proportional spatial distribution of viscous damping. Gravity loads and state-dependent vehicle, track and wheel-rail contact conditions are accounted for as external loads on the modal model, including situations involving loss of (and recovered) wheel-rail contact, impact between hanging sleeper and ballast, and/or a prescribed variation of non-linear track support stiffness properties along the track model. The procedure is demonstrated by calculating the degradation of longitudinal level over time as initiated by a prescribed initial local rail irregularity (dipped welded rail joint).

Potential use of an ultrasound antifouling technology as a ballast water treatment system

NASA Astrophysics Data System (ADS)

Estévez-Calvar, Noelia; Gambardella, Chiara; Miraglia, Francesco; Pavanello, Giovanni; Greco, Giuliano; Faimali, Marco; Garaventa, Francesca

2018-03-01

The aim of this study was to investigate, at a laboratory scale, the potentialities of an ultrasound-based treatment initially designed to eliminate fouling, as a ballast water treatment system. Therefore, early life stages of three different zooplanktonic species (Amphibalanus amphitrite, Brachionus plicatilis and Artemia salina) were exposed to ultrasound waves (20-22 kHz). The experimental set up included static assays with variations of time exposure (30 s, 60 s and 30 s on/60 s off/30 s on), material of tanks (stainless steel, galvanized steel and plastic) and position of the ultrasound source. Results showed that the treatment efficacy increased from 30 to 60 s and no differences were registered between 60 s-continuous exposure and pulse exposure. The highest efficacy was observed in Experiment I (metal-to-metal contact assay) with a mortality value of 93-95% for B. plicatilis and A. salina. It consisted of organisms located inside stainless steel tubes that were located in direct contact with the ultrasound source and treated for 60 s. Further, we found that, generally, A. amphitrite and B. plicatilis were the most resistant species to the ultrasound treatment whereas A. salina was the most sensitive. We further discuss that US may unlikely be used for commercial vessels, but may be used to treat ballast water in smaller ballast tanks as on board of mega yachts.

An evaluation of the residual toxicity and chemistry of a sodium hydroxide-based ballast water treatment system for freshwater ships.

PubMed

Elskus, Adria A; Ingersoll, Christopher G; Kemble, Nile E; Echols, Kathy R; Brumbaugh, William G; Henquinet, Jeffrey W; Watten, Barnaby J

2015-06-01

Nonnative organisms in the ballast water of freshwater ships must be killed to prevent the spread of invasive species. The ideal ballast water treatment system (BWTS) would kill 100% of ballast water organisms with minimal residual toxicity to organisms in receiving waters. In the present study, the residual toxicity and chemistry of a BWTS was evaluated. Sodium hydroxide was added to elevate pH to >11.5 to kill ballast water organisms, then reduced to pH <9 by sparging with wet-scrubbed diesel exhaust (the source of CO2 ). Cladocerans (Ceriodaphnia dubia), amphipods (Hyalella azteca), and fathead minnows (Pimephales promelas) were exposed for 2 d to BWTS water under an air atmosphere (pH drifted to ≥9) or a 2.5% CO2 atmosphere (pH 7.5-8.2), then transferred to control water for 5 d to assess potential delayed toxicity. Chemical concentrations in the BWTS water met vessel discharge guidelines with the exception of concentrations of copper. There was little to no residual toxicity to cladocerans or fish, but the BWTS water was toxic to amphipods. Maintaining a neutral pH and diluting BWTS water by 50% eliminated toxicity to the amphipods. The toxicity of BWTS water would likely be minimal because of rapid dilution in the receiving water, with subsurface release likely preventing pH rise. This BWTS has the potential to become a viable method for treating ballast water released into freshwater systems. © 2015 SETAC.

An evaluation of the residual toxicity and chemistry of a sodium hydroxide-based ballast water treatment system for freshwater ships

USGS Publications Warehouse

Elskus, Adria; Ingersoll, Christopher G.; Kemble, Nile E.; Echols, Kathy R.; Brumbaugh, William G.; Henquinet, Jeffrey; Watten, Barnaby J.

2015-01-01

Nonnative organisms in the ballast water of freshwater ships must be killed to prevent the spread of invasive species. The ideal ballast water treatment system (BWTS) would kill 100% of ballast water organisms with minimal residual toxicity to organisms in receiving waters. In the present study, the residual toxicity and chemistry of a BWTS was evaluated. Sodium hydroxide was added to elevate pH to >11.5 to kill ballast water organisms, then reduced to pH <9 by sparging with wet-scrubbed diesel exhaust (the source of CO2). Cladocerans (Ceriodaphnia dubia), amphipods (Hyalella azteca), and fathead minnows (Pimephales promelas) were exposed for 2 d to BWTS water under an air atmosphere (pH drifted to ≥9) or a 2.5% CO2 atmosphere (pH 7.5–8.2), then transferred to control water for 5 d to assess potential delayed toxicity. Chemical concentrations in the BWTS water met vessel discharge guidelines with the exception of concentrations of copper. There was little to no residual toxicity to cladocerans or fish, but the BWTS water was toxic to amphipods. Maintaining a neutral pH and diluting BWTS water by 50% eliminated toxicity to the amphipods. The toxicity of BWTS water would likely be minimal because of rapid dilution in the receiving water, with subsurface release likely preventing pH rise. This BWTS has the potential to become a viable method for treating ballast water released into freshwater systems.

33 CFR 155.370 - Oily mixture (bilge slops)/fuel oil tank ballast water discharges on oceangoing ships of 10,000...

Code of Federal Regulations, 2012 CFR

2012-07-01

... 33 Navigation and Navigable Waters 2 2012-07-01 2012-07-01 false Oily mixture (bilge slops)/fuel oil tank ballast water discharges on oceangoing ships of 10,000 gross tons and above and oceangoing ships of 400 gross tons and above that carry ballast water in their fuel oil tanks. 155.370 Section 155.370 Navigation and Navigable Waters COAST GUAR...

33 CFR 155.370 - Oily mixture (bilge slops)/fuel oil tank ballast water discharges on oceangoing ships of 10,000...

Code of Federal Regulations, 2014 CFR

2014-07-01

... 33 Navigation and Navigable Waters 2 2014-07-01 2014-07-01 false Oily mixture (bilge slops)/fuel oil tank ballast water discharges on oceangoing ships of 10,000 gross tons and above and oceangoing ships of 400 gross tons and above that carry ballast water in their fuel oil tanks. 155.370 Section 155.370 Navigation and Navigable Waters COAST GUAR...

33 CFR 155.370 - Oily mixture (bilge slops)/fuel oil tank ballast water discharges on oceangoing ships of 10,000...

Code of Federal Regulations, 2013 CFR

2013-07-01

... 33 Navigation and Navigable Waters 2 2013-07-01 2013-07-01 false Oily mixture (bilge slops)/fuel oil tank ballast water discharges on oceangoing ships of 10,000 gross tons and above and oceangoing ships of 400 gross tons and above that carry ballast water in their fuel oil tanks. 155.370 Section 155.370 Navigation and Navigable Waters COAST GUAR...

33 CFR 155.370 - Oily mixture (bilge slops)/fuel oil tank ballast water discharges on oceangoing ships of 10,000...

Code of Federal Regulations, 2011 CFR

2011-07-01

... 33 Navigation and Navigable Waters 2 2011-07-01 2011-07-01 false Oily mixture (bilge slops)/fuel oil tank ballast water discharges on oceangoing ships of 10,000 gross tons and above and oceangoing ships of 400 gross tons and above that carry ballast water in their fuel oil tanks. 155.370 Section 155.370 Navigation and Navigable Waters COAST GUAR...

Rapid molecular detection of invasive species in ballast and harbor water by integrating environmental DNA and light transmission spectroscopy.

PubMed

Egan, Scott P; Grey, Erin; Olds, Brett; Feder, Jeffery L; Ruggiero, Steven T; Tanner, Carol E; Lodge, David M

2015-04-07

Invasive species introduced via the ballast water of commercial ships cause enormous environmental and economic damage worldwide. Accurate monitoring for these often microscopic and morphologically indistinguishable species is challenging but critical for mitigating damages. We apply eDNA sampling, which involves the filtering and subsequent DNA extraction of microscopic bits of tissue suspended in water, to ballast and harbor water sampled during a commercial ship's 1400 km voyage through the North American Great Lakes. Using a lab-based gel electrophoresis assay and a rapid, field-ready light transmission spectroscopy (LTS) assay, we test for the presence of two invasive species: quagga (Dreissena bugensis) and zebra (D. polymorpha) mussels. Furthermore, we spiked a set of uninfested ballast and harbor samples with zebra mussel tissue to further test each assay's detection capabilities. In unmanipulated samples, zebra mussel was not detected, while quagga mussel was detected in all samples at a rate of 85% for the gel assay and 100% for the LTS assay. In the spiked experimental samples, both assays detected zebra mussel in 94% of spiked samples and 0% of negative controls. Overall, these results demonstrate that eDNA sampling is effective for monitoring ballast-mediated invasions and that LTS has the potential for rapid, field-based detection.

Pandemic serotypes of Vibrio cholerae isolated from ships' ballast tanks and coastal waters: assessment of antibiotic resistance and virulence genes (tcpA and ctxA).

PubMed

Dobbs, Fred C; Goodrich, Amanda L; Thomson, Frank K; Hynes, Wayne

2013-05-01

There is concern that ships' ballasting operations may disseminate Vibrio cholerae to ports throughout the world. Given evidence that the bacterium is indeed transported by ships, we isolated pandemic serotypes O1 and O139 from ballast tanks and characterized them with respect to antibiotic resistance and virulence genes ctxA and tcpA. We carried out concurrent studies with V. cholerae isolated from coastal waters. Of 284 isolates, 30 were serotype O1 and 59 were serotype O139. These serotypes were overrepresented in ballast tanks relative to the coastal waters sampled. All locations, whether coastal waters or ballast tanks, yielded samples from which serotype O1, O139, or both were isolated. There were three groups among the 62 isolates for which antibiotic characterization was conclusive: those exhibiting β-lactamase activity and resistance to at least one of the 12 antibiotics tested; those negative for β-lactamase but having antibiotic resistance; those negative for β-lactamase and registering no antibiotic resistance. When present, antibiotic resistance in nearly all cases was to ampicillin; resistance to multiple antibiotics was uncommon. PCR assays revealed that none of the isolates contained the ctxA gene and only two isolates, one O139 and one O1, contained the tcpA gene; both isolates originated from ballast water. These results support the bacteriological regulations proposed by the International Maritime Association for discharged ballast water.

Application of Ion Torrent Sequencing to the Assessment of the Effect of Alkali Ballast Water Treatment on Microbial Community Diversity

PubMed Central

Fujimoto, Masanori; Moyerbrailean, Gregory A.; Noman, Sifat; Gizicki, Jason P.; Ram, Michal L.; Green, Phyllis A.; Ram, Jeffrey L.

2014-01-01

The impact of NaOH as a ballast water treatment (BWT) on microbial community diversity was assessed using the 16S rRNA gene based Ion Torrent sequencing with its new 400 base chemistry. Ballast water samples from a Great Lakes ship were collected from the intake and discharge of both control and NaOH (pH 12) treated tanks and were analyzed in duplicates. One set of duplicates was treated with the membrane-impermeable DNA cross-linking reagent propidium mono-azide (PMA) prior to PCR amplification to differentiate between live and dead microorganisms. Ion Torrent sequencing generated nearly 580,000 reads for 31 bar-coded samples and revealed alterations of the microbial community structure in ballast water that had been treated with NaOH. Rarefaction analysis of the Ion Torrent sequencing data showed that BWT using NaOH significantly decreased microbial community diversity relative to control discharge (p<0.001). UniFrac distance based principal coordinate analysis (PCoA) plots and UPGMA tree analysis revealed that NaOH-treated ballast water microbial communities differed from both intake communities and control discharge communities. After NaOH treatment, bacteria from the genus Alishewanella became dominant in the NaOH-treated samples, accounting for <0.5% of the total reads in intake samples but more than 50% of the reads in the treated discharge samples. The only apparent difference in microbial community structure between PMA-processed and non-PMA samples occurred in intake water samples, which exhibited a significantly higher amount of PMA-sensitive cyanobacteria/chloroplast 16S rRNA than their corresponding non-PMA total DNA samples. The community assembly obtained using Ion Torrent sequencing was comparable to that obtained from a subset of samples that were also subjected to 454 pyrosequencing. This study showed the efficacy of alkali ballast water treatment in reducing ballast water microbial diversity and demonstrated the application of new Ion Torrent

Application of ion torrent sequencing to the assessment of the effect of alkali ballast water treatment on microbial community diversity.

PubMed

Fujimoto, Masanori; Moyerbrailean, Gregory A; Noman, Sifat; Gizicki, Jason P; Ram, Michal L; Green, Phyllis A; Ram, Jeffrey L

2014-01-01

The impact of NaOH as a ballast water treatment (BWT) on microbial community diversity was assessed using the 16S rRNA gene based Ion Torrent sequencing with its new 400 base chemistry. Ballast water samples from a Great Lakes ship were collected from the intake and discharge of both control and NaOH (pH 12) treated tanks and were analyzed in duplicates. One set of duplicates was treated with the membrane-impermeable DNA cross-linking reagent propidium mono-azide (PMA) prior to PCR amplification to differentiate between live and dead microorganisms. Ion Torrent sequencing generated nearly 580,000 reads for 31 bar-coded samples and revealed alterations of the microbial community structure in ballast water that had been treated with NaOH. Rarefaction analysis of the Ion Torrent sequencing data showed that BWT using NaOH significantly decreased microbial community diversity relative to control discharge (p<0.001). UniFrac distance based principal coordinate analysis (PCoA) plots and UPGMA tree analysis revealed that NaOH-treated ballast water microbial communities differed from both intake communities and control discharge communities. After NaOH treatment, bacteria from the genus Alishewanella became dominant in the NaOH-treated samples, accounting for <0.5% of the total reads in intake samples but more than 50% of the reads in the treated discharge samples. The only apparent difference in microbial community structure between PMA-processed and non-PMA samples occurred in intake water samples, which exhibited a significantly higher amount of PMA-sensitive cyanobacteria/chloroplast 16S rRNA than their corresponding non-PMA total DNA samples. The community assembly obtained using Ion Torrent sequencing was comparable to that obtained from a subset of samples that were also subjected to 454 pyrosequencing. This study showed the efficacy of alkali ballast water treatment in reducing ballast water microbial diversity and demonstrated the application of new Ion Torrent

Ballasting pipeline moving in horizontal well as method of control sticking phenomenon

NASA Astrophysics Data System (ADS)

Toropov, V. S.; Toropov, E. S.

2018-05-01

The mechanism of the phenomenon of sticking a pipeline moving in a well while pulled by the facility horizontal directional drilling is investigated. A quantitative evaluation of the force arising from sticking is given. At the same time, the working hypothesis takes a view of the combined effect of adhesion and friction interactions as the reasons that cause this phenomenon. As a measure to control the occurrence of sticking and to reduce the resistance force to movement of the pipeline in the well, several methods of ballasting the working pipeline are proposed, depending on the profile of the well and the ratio of the length of the curved sections of the inlet and outlet and the straight horizontal sections of the profile. It is shown that for crossings, which profile contains an extended horizontal section, it is possible to partially fill the pipeline with water to achieve zero buoyancy, and for crossings with curvature along the entire profile, the ballasting efficiency will be minimal.

Failure of the public health testing program for ballast water treatment systems.

PubMed

Cohen, Andrew N; Dobbs, Fred C

2015-02-15

Since 2004, an international testing program has certified 53 shipboard treatment systems as meeting ballast water discharge standards, including limits on certain microbes to prevent the spread of human pathogens. We determined how frequently certification tests failed a minimum requirement for a meaningful evaluation, that the concentration of microbes in the untreated (control) discharge must exceed the regulatory limit for treated discharges. In 95% of cases where the result was accepted as evidence that the treatment system reduced microbes to below the regulatory limit, the discharge met the limit even without treatment. This shows that the certification program for ballast water treatment systems is dysfunctional in protecting human health. In nearly all cases, the treatment systems would have equally well "passed" these tests even if they had never been turned on. Protocols must require minimum concentrations of targeted microbes in test waters, reflecting the upper range of concentrations in waters where ships operate. Copyright © 2014 Elsevier Ltd. All rights reserved.

Gust wind tunnel study on ballast pick-up by high-speed trains

NASA Astrophysics Data System (ADS)

Navarro-Medina, F.; Sanz-Andres, A.; Perez-Grande, I.

2012-01-01

This paper describes the experimental setup, procedure, and results obtained, concerning the dynamics of a body lying on a floor, attached to a hinge, and exposed to an unsteady flow, which is a model of the initiation of rotational motion of ballast stones due to the wind generated by the passing of a high-speed train. The idea is to obtain experimental data to support the theoretical model developed in Sanz-Andres and Navarro-Medina (J Wind Eng Ind Aerodyn 98, 772-783, (2010), aimed at analyzing the initial phase of the ballast train-induced-wind erosion (BATIWE) phenomenon. The experimental setup is based on an open circuit, closed test section, low-speed wind tunnel, with a new sinusoidal gust generator mechanism concept, designed and built at the IDR/UPM. The tunnel's main characteristic is the ability to generate a flow with a uniform velocity profile and sinusoidal time fluctuation of the speed. Experimental results and theoretical model predictions are in good agreement.

Global ballast water management and the "same location" concept: a clear term or a clear issue?

PubMed

David, Matej; Gollasch, Stephan; Pavliha, Marko

2013-03-01

The United Nations recognized the transfer of harmful organisms and pathogens across natural barriers as one of the four greatest pressures to the world's oceans and seas, causing global environmental changes, while also posing a threat to human health, property, and resources. Ballast water transferred by vessels was recognized as a prominent vector of such species and was regulated by the International Convention for the Control and Management of Ship's Ballast Water and Sediments (2004). Permanent exceptions from ballast water management requirements may apply when the uptake and discharge of ballast water occur at the "same location." However, the "same location" concept may be interpreted differently, e.g., a port basin, a port, an anchorage, or a larger area even with more ports inside. Considering that the Convention is nearing the beginning of enforcement, national authorities all around the world will soon be exposed to applications for exceptions. Here we consider possible effects of different interpretations of the "same location" concept. We have considered different possible extensions of the same location through environmental, shipping, and legal aspects. The extension of such areas, and the inclusion of more ports, may compromise the Convention's main purpose. We recommend that "same location" mean the smallest practicable unit, i.e., the same harbor, mooring, or anchorage. An entire smaller port, possibly also including the anchorage, could be considered as same location. For larger ports with a gradient of environmental conditions, "same location" should mean a terminal or a port basin. We further recommend that IMO consider the preparation of a guidance document to include concepts, criteria, and processes outlining how to identify "same location," which limits should be clearly identified.

Ballast and Subgrade requirements study : railroad track substructure - design and performance evaluation practices

DOT National Transportation Integrated Search

1983-06-30

Earth materials--i.e., soil and rock--form the substructure (ballast, subballast, and subgrade) of all railroad track. In this report, the most suitable technology and design criteria as related to design of the substructure are identified based on a...

Developing and testing an Early Warning System for Non Indigenous Species and Ballast Water Management

NASA Astrophysics Data System (ADS)

Magaletti, Erika; Garaventa, Francesca; David, Matej; Castriota, Luca; Kraus, Romina; Luna, Gian Marco; Silvestri, Cecilia; Forte, Cosmo; Bastianini, Mauro; Falautano, Manuela; Maggio, Teresa; Rak, Giulietta; Gollasch, Stephan

2018-03-01

This paper describes the methodological approach used for the development of an Early Warning System (EWS) for Non Indigenous Species (NIS) and ballast water management and summarizes the results obtained. The specific goals of the EWS are firstly to warn vessels to prevent loading of ballast water when critical biological conditions occur in ports and surrounding areas i.e. mass development or blooms of Harmful Aquatic Organisms and Pathogens (HAOP). Secondly, to warn environmental and health authorities when NIS or pathogens are present in ports or surrounding areas to enable an early response and an implementation of remediation measures. The EWS is designed to be used for implementing various parallel obligations, by taking into consideration different legal scopes, associated information and decision-making needs. The EWS was elaborated, tested in the Adriatic Sea and illustrated by two case studies. Although the EWS was developed with an Adriatic Sea focus, it is presented in a format so that it may be used as a model when establishing similar systems in other locations. The role of the various actors is discussed and recommendations on further developments of the EWS are presented. It was concluded that the EWS is a suitable tool to reduce the spread of potentially harmful and ballast water mediated species.

Risk assessment of human health from exposure to the discharged ballast water after full-scale electrolysis treatment.

PubMed

Zhang, Nahui; Wang, Yidan; Xue, Junzeng; Yuan, Lin; Wang, Qiong; Liu, Liang; Wu, Huixian; Hu, Kefeng

2016-06-01

The presence of disinfection by-products (DBPs) releasing from ballast water management systems (BWMS) can cause a possible adverse effects on humans. The objectives of this study were to compute the Derived No Effect Levels (DNELs) for different exposure scenarios and to compare these levels with the exposure levels from the measured DBPs in treated ballast water. The risk assessment showed that when using animal toxicity data, all the DNELs values were approximately 10(3)-10(12) times higher than the exposure levels of occupational and general public exposure scenarios, indicating the level of risk was low (risk characterization ratios (RCRs) < 1). However, when using human data, the RCRs were higher than 1 for dichlorobromomethane and trichloromethane, indicating that the risk of adverse effects on human were significant. This implies that there are apparent discrepancies between risk characterization from animal and human data, which may affect the overall results. We therefore recommend that when appropriate, human data should be used in risk assessment as much as possible, although human data are very limited. Moreover, more appropriate assessment factors can be considered to be employed in estimating the DNELs for human when the animal data is selected as the dose descriptors. Copyright © 2016 Elsevier Inc. All rights reserved.

33 CFR 155.440 - Segregation of fuel oil and ballast water on new oceangoing ships of 4,000 gross tons and above...

Code of Federal Regulations, 2011 CFR

2011-07-01

... 33 Navigation and Navigable Waters 2 2011-07-01 2011-07-01 false Segregation of fuel oil and ballast water on new oceangoing ships of 4,000 gross tons and above, other than oil tankers, and on new... PREVENTION REGULATIONS FOR VESSELS Vessel Equipment § 155.440 Segregation of fuel oil and ballast water on...

33 CFR 155.440 - Segregation of fuel oil and ballast water on new oceangoing ships of 4,000 gross tons and above...

Code of Federal Regulations, 2010 CFR

2010-07-01

... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Segregation of fuel oil and ballast water on new oceangoing ships of 4,000 gross tons and above, other than oil tankers, and on new... PREVENTION REGULATIONS FOR VESSELS Vessel Equipment § 155.440 Segregation of fuel oil and ballast water on...

New Mass Properties Engineers Aerospace Ballasting Challenge Facilitated by the SAWE Community

NASA Technical Reports Server (NTRS)

Cutright, Amanda; Shaughnessy, Brendan

2010-01-01

The discipline of Mass Properties Engineering tends to find the engineers; not typically vice versa. In this case, two engineers quickly found their new responsibilities deep in many aspects of mass properties engineering and required to meet technical challenges in a fast paced environment. As part of NASA's Constellation Program, a series of flight tests will be conducted to evaluate components of the new spacecraft launch vehicles. One of these tests is the Pad Abort 1 (PA-1) flight test which will test the Launch Abort System (LAS), a system designed to provide escape for astronauts in the event of an emergency. The Flight Test Articles (FTA) used in this flight test are required to match mass properties corresponding to the operational vehicle, which has a continually evolving design. Additionally, since the structure and subsystems for the Orion Crew Module (CM) FTA are simplified versions of the final product, thousands of pounds of ballast are necessary to achieve the desired mass properties. These new mass properties engineers are responsible for many mass properties aspects in support of the flight test, including meeting the ballasting challenge for the CM Boilerplate FTA. SAWE expert and experienced mass properties engineers, both those that are directly on the team and many that supported via a variety of Society venues, significantly contributed to facilitating the success of addressing this particular mass properties ballasting challenge, in addition to many other challenges along the way. This paper discusses the details regarding the technical aspects of this particular mass properties challenge, as well as identifies recommendations for new mass properties engineers that were learned from the SAWE community along the way.

Technology selection for ballast water treatment by multi-stakeholders: A multi-attribute decision analysis approach based on the combined weights and extension theory.

PubMed

Ren, Jingzheng

2018-01-01

This objective of this study is to develop a generic multi-attribute decision analysis framework for ranking the technologies for ballast water treatment and determine their grades. An evaluation criteria system consisting of eight criteria in four categories was used to evaluate the technologies for ballast water treatment. The Best-Worst method, which is a subjective weighting method and Criteria importance through inter-criteria correlation method, which is an objective weighting method, were combined to determine the weights of the evaluation criteria. The extension theory was employed to prioritize the technologies for ballast water treatment and determine their grades. An illustrative case including four technologies for ballast water treatment, i.e. Alfa Laval (T 1 ), Hyde (T 2 ), Unitor (T 3 ), and NaOH (T 4 ), were studied by the proposed method, and the Hyde (T 2 ) was recognized as the best technology. Sensitivity analysis was also carried to investigate the effects of the combined coefficients and the weights of the evaluation criteria on the final priority order of the four technologies for ballast water treatment. The sum weighted method and the TOPSIS was also employed to rank the four technologies, and the results determined by these two methods are consistent to that determined by the proposed method in this study. Copyright © 2017 Elsevier Ltd. All rights reserved.

Abundances and profiles of antibiotic resistance genes as well as co-occurrences with human bacterial pathogens in ship ballast tank sediments from a shipyard in Jiangsu Province, China.

PubMed

Lv, Baoyi; Cui, Yuxue; Tian, Wen; Li, Jing; Xie, Bing; Yin, Fang

2018-08-15

Ship ballasting operations may transfer harmful aquatic organisms across global ocean. This study aims to reveal the occurrences and abundances of antibiotic resistance genes (ARGs) and human bacterial pathogens (HBPs) in ballast tank sediments. Nine samples were collected and respectively analyzed by real-time quantitative PCR and high-throughput sequencing technologies. Ten ARGs (aadA1, blaCTX-M, blaTEM, ermB, mefA, strB, sul1, sul2, tetM, and tetQ) and the Class-I integron gene (intI1) were highly prevalent (10 5 -10 9 gene copies/g) in ballast tank sediments. The sul1 was the most abundant ARG with the concentration of 10 8 -10 9 copies/g and intI1 was much more abundant than the ARGs in ballast tank sediments. The strong positive correlations between intI1 and ARGs (blaCTX-M, sul1, sul2 and tetM) indicated the potential spread of ARGs via horizontal gene transfer. In ballast tank sediments, 44 bacterial species were identified as HBPs and accounted for 0.13-21.46% of the total bacterial population although the three indicator pathogenic microbes (Vibrio cholerae, Escherichia coli, and Enterococci) proposed by the International Maritime Organization were not detected. Pseudomonas pseudoalcaligenes, Enterococcus hirae, Shigella sonnei and Bacillus anthracis were the dominant pathogens in ballast tank sediments. Zn and P in sediments had positive effects on the ARGs. Network analysis results indicated that sul1 and sul2 genes existed in several bacterial pathogens. Ballast tank sediments could be regarded as a carrier for the migration of ARGs. It is important to manage ballast tank sediments reasonably in order to prevent the dissemination of ARGs and bacterial pathogens. Copyright © 2018 Elsevier Inc. All rights reserved.

Counting at low concentrations: the statistical challenges of verifying ballast water discharge standards

EPA Science Inventory

Discharge from the ballast tanks of ships is one of the primary vectors of nonindigenous species in marine environments. To mitigate this environmental and economic threat, the U.S. Coast Guard and the U.S. Environmental Protection Agency will regulate the concentration of livin...

Changes in Microbial Communities, Including both Uncultured and Culturable Bacteria, with Mid-Ocean Ballast-Water Exchange during a Voyage from Japan to Australia

PubMed Central

Tomaru, Akiko; Kawachi, Masanobu; Demura, Mikihide; Fukuyo, Yasuwo

2014-01-01

We assessed changes in the microbial communities in ballast water during a trans-Pacific voyage from Japan to Australia that included a mid-ocean ballast-water exchange. Uncultured (i.e., total) and culturable bacteria were counted and were characterized by using denaturing gradient gel electrophoresis (DGGE). There was a clear decrease over time in numbers of uncultured microorganisms, except for heterotrophic nanoflagellates, whereas the abundance of culturable bacteria initially decreased after the ballast-water exchange but then increased. The increase, however, was only up to 5.34% of the total number of uncultured bacteria. Cluster analysis showed that the DGGE profiles of uncultured bacteria clearly changed after the exchange. In contrast, there was no clear change in the DGGE profiles of culturable bacteria after the exchange. Multidimensional scaling analysis showed changes in microbial communities over the course of the voyage. Although indicator microbes as defined by the International Convention for the Control and Management of Ships' Ballast Water and Sediments were occasionally detected, no coliform bacteria were detected after the exchange. PMID:24817212

33 CFR 151.2035 - What are the required ballast water management practices for my vessel?

Code of Federal Regulations, 2010 CFR

2010-07-01

... regulations. (4) Discharge only the minimal amount of ballast water essential for vessel operations while in... operating beyond the Exclusive Economic Zone, you (the master, operator, or person-in-charge of a vessel...

Laboratory tests on heat treatment of ballast water using engine waste heat.

PubMed

Balaji, Rajoo; Lee Siang, Hing; Yaakob, Omar; Koh, Kho King; Adnan, Faizul Amri Bin; Ismail, Nasrudin Bin; Ahmad, Badruzzaman Bin; Ismail, Mohd Arif Bin; Wan Nik, W B

2018-05-01

Waste heat recovery from shipboard machineries could be a potential source for heat treatment of ballast water. Similar to a shipboard schematic arrangement, a laboratory-scale engine-heat exchanger set-up harvesting waste heat from jacket water and exhaust gases was erected to test the level of species' mortalities. Mortalities were also assessed under experimental conditions for cultured and natural plankton communities at laboratory level. Effect of pump impellers on species' mortalities were also tested. Exposures between 60°C and 70°C for 60 sec resulted in 80-100% mortalities. Mortalities due to pump impeller effects were observed in the range of 70-100% for zooplankton. On the laboratory-scale arrangement, >95% mortalities of phytoplankton, zooplankton and bacteria were recorded. It was demonstrated that the temperature of tropical sea waters used as secondary coolant can be raised to cause species' mortalities, employing engine exhaust gases. The results also indicated that pump impeller effects will enhance species' mortalities. The limitations of the shipboard application of this method would be the large ballast volumes, flow rates and time for treatment.

Development of Viscoelastic Multi-Body Simulation and Impact Response Analysis of a Ballasted Railway Track under Cyclic Loading.

PubMed

Nishiura, Daisuke; Sakaguchi, Hide; Aikawa, Akira

2017-06-03

Simulation of a large number of deformable bodies is often difficult because complex high-level modeling is required to address both multi-body contact and viscoelastic deformation. This necessitates the combined use of a discrete element method (DEM) and a finite element method (FEM). In this study, a quadruple discrete element method (QDEM) was developed for dynamic analysis of viscoelastic materials using a simpler algorithm compared to the standard FEM. QDEM easily incorporates the contact algorithm used in DEM. As the first step toward multi-body simulation, the fundamental performance of QDEM was investigated for viscoelastic analysis. The amplitude and frequency of cantilever elastic vibration were nearly equal to those obtained by the standard FEM. A comparison of creep recovery tests with an analytical solution showed good agreement between them. In addition, good correlation between the attenuation degree and the real physical viscosity was confirmed for viscoelastic vibration analysis. Therefore, the high accuracy of QDEM in the fundamental analysis of infinitesimal viscoelastic deformations was verified. Finally, the impact response of a ballast and sleeper under cyclic loading on a railway track was analyzed using QDEM as an application of deformable multi-body dynamics. The results showed that the vibration of the ballasted track was qualitatively in good agreement with the actual measurements. Moreover, the ballast layer with high friction reduced the ballasted track deterioration. This study suggests that QDEM, as an alternative to DEM and FEM, can provide deeper insights into the contact dynamics of a large number of deformable bodies.

Development of Viscoelastic Multi-Body Simulation and Impact Response Analysis of a Ballasted Railway Track under Cyclic Loading

PubMed Central

Nishiura, Daisuke; Sakaguchi, Hide; Aikawa, Akira

2017-01-01

Simulation of a large number of deformable bodies is often difficult because complex high-level modeling is required to address both multi-body contact and viscoelastic deformation. This necessitates the combined use of a discrete element method (DEM) and a finite element method (FEM). In this study, a quadruple discrete element method (QDEM) was developed for dynamic analysis of viscoelastic materials using a simpler algorithm compared to the standard FEM. QDEM easily incorporates the contact algorithm used in DEM. As the first step toward multi-body simulation, the fundamental performance of QDEM was investigated for viscoelastic analysis. The amplitude and frequency of cantilever elastic vibration were nearly equal to those obtained by the standard FEM. A comparison of creep recovery tests with an analytical solution showed good agreement between them. In addition, good correlation between the attenuation degree and the real physical viscosity was confirmed for viscoelastic vibration analysis. Therefore, the high accuracy of QDEM in the fundamental analysis of infinitesimal viscoelastic deformations was verified. Finally, the impact response of a ballast and sleeper under cyclic loading on a railway track was analyzed using QDEM as an application of deformable multi-body dynamics. The results showed that the vibration of the ballasted track was qualitatively in good agreement with the actual measurements. Moreover, the ballast layer with high friction reduced the ballasted track deterioration. This study suggests that QDEM, as an alternative to DEM and FEM, can provide deeper insights into the contact dynamics of a large number of deformable bodies. PMID:28772974

Bromination of Marine Dissolved Organic Matter following Full Scale Electrochemical Ballast Water Disinfection.

PubMed

Gonsior, Michael; Mitchelmore, Carys; Heyes, Andrew; Harir, Mourad; Richardson, Susan D; Petty, William Tyler; Wright, David A; Schmitt-Kopplin, Philippe

2015-08-04

An extensively diverse array of brominated disinfection byproducts (DBPs) were generated following electrochemical disinfection of natural coastal/estuarine water, which is one of the main treatment methods currently under consideration for ballast water treatment. Ultra-high-resolution mass spectrometry revealed 462 distinct brominated DBPs at a relative abundance in the mass spectra of more than 1%. A brominated DBP with a relative abundance of almost 22% was identified as 2,2,4-tribromo-5-hydroxy-4-cyclopentene-1,3-dione, which is an analogue to several previously described 2,2,4-trihalo-5-hydroxy-4-cyclopentene-1,3-diones in drinking water. Several other brominated molecular formulas matched those of other known brominated DBPs, such as dibromomethane, which could be generated by decarboxylation of dibromoacetic acid during ionization, dibromophenol, dibromopropanoic acid, dibromobutanoic acid, bromohydroxybenzoic acid, bromophenylacetic acid, bromooxopentenoic acid, and dibromopentenedioic acid. Via comparison to previously described chlorine-containing analogues, bromophenylacetic acid, dibromooxopentenoic acid, and dibromopentenedioic acid were also identified. A novel compound at a 4% relative abundance was identified as tribromoethenesulfonate. This compound has not been previously described as a DBP, and its core structure of tribromoethene has been demonstrated to show toxicological implications. Here we show that electrochemical disinfection, suggested as a candidate for successful ballast water treatment, caused considerable production of some previously characterized DBPs in addition to novel brominated DBPs, although several hundred compounds remain structurally uncharacterized. Our results clearly demonstrate that electrochemical and potentially direct chlorination of ballast water in estuarine and marine systems should be approached with caution and the concentrations, fate, and toxicity of DBP need to be further characterized.

Ballast system for maintaining constant pressure in a glove box

NASA Technical Reports Server (NTRS)

Shlichta, Paul J. (Inventor)

1990-01-01

A ballast system for a glove box including a fixed platform on which is mounted an inflatable bag on top of which resides a cover and a weight. The variable gas volume of the inflatable bag communicates with that of the glove box via a valved tube. The weight and gas volume are selected to maintain a relatively constant pressure in the glove box despite variations in the glove box volume while avoiding the use of complicated valving apparatus.

Effects of sonication and advanced chemical oxidants on the unicellular green alga Dunaliella tertiolecta and cysts, larvae and adults of the brine shrimp Artemia salina: a prospective treatment to eradicate invasive organisms from ballast water.

PubMed

Gavand, Meghana R; McClintock, James B; Amsler, Charles D; Peters, Robert W; Angus, Robert A

2007-11-01

Uptake and release of ship-borne ballast water is a major factor contributing to introductions of aquatic phytoplankton and invasive macroinvertebrates. Some invasive unicellular algae can cause harmful algal blooms and produce toxins that build up in food chains. Moreover, to date, few studies have compared the efficacy of ballast water treatments against different life history phases of aquatic macroinvertebrates. In the present study, the unicellular green alga Dunaliella tertiolecta, and three discrete life history phases of the brine shrimp Artemia salina, were independently used as model organisms to study the efficacy of sonication as well as the advanced oxidants, hydrogen peroxide and ozone, as potential ballast water treatments. Algal cells and brine shrimp cysts, nauplii, and adults were subjected to individual and combined treatments of sonication and advanced oxidants. Combined rather than individual treatments consistently yielded the highest levels of mortality in algal cells (100% over a 2 min exposure) and in brine shrimp (100% and 95% for larvae and adults, respectively, over a 2 min exposure). In contrast, mortality levels in brine shrimp cysts (66% over 2 min; increased to 92% over a 20 min exposure) were moderately high but consistently lower than that detected for larval or adult shrimp. Our results indicate that a combination of sonication and advanced chemical oxidants may be a promising method to eradicate aquatic unicellular algae and macroinvertebrates in ballast water.

The effects of chemical additives on the production of disinfection byproducts and ecotoxicity in simulated ballast water

NASA Astrophysics Data System (ADS)

Park, Chul; Cha, Hyung-Gon; Lee, Ji-Hyun; Choi, Tae Seop; Lee, Jungsuk; Kim, Young-Hee; Bae, Minjung; Shin, Kyoungsoon; Choi, Keun-Hyung

2017-11-01

The management of ship ballast water is essential to stemming the introduction of non-indigenous species. Approval for onboard installation of a system to treat ballast water requires rigorous land-based testing as dictated in the G8 guideline by the International Maritime Organization. However, this testing lacks standardization-most notably augmentation of organic carbon for influent water by adding chemical additives. Electrochlorination is a popular treatment method for ballast water, in which chlorinated oxidants react with organisms and organic matter in water. The additives could thus affect the treatment efficacy of the ballast water. Here, we examined the effects of several candidates of organic carbon additives on the consumption of total residual oxidant (TRO), the production of disinfection byproducts (DBPs), plankton survival, and ecotoxicity. The TRO consumption over five days of storage was higher in electrochlorinated seawater amended with lignin and Metamucil when compared with seawaters with other organic carbon compounds. DBP production varied by almost two orders of magnitude as a function of the various additives. This was largely attributed to the production of tribromomethane and dibromoacetic acid. The survival of Artemia franciscana was significantly different across waters of different organic carbon additives. Algal toxicity testing with the marine haptophyte Isochrysis galbana significantly reduced growth in lignin- and Metamucil-treated seawaters, but not with other organic carbon compounds. Bioluminescence in Vibrio fischeri sharply declined in electrochlorinated seawaters with all types of organic carbon compounds, but no toxicity was manifested once the electrochlorinated seawaters were neutralized with sodium thiosulfate. The varying degrees of outcome suggest that it might be better to eliminate the requirements of adding organic carbon to test water as long as natural water was used for land-based testing of BWMS. If needed, the

Railroad Tie Responses to Directly Applied Rail Seat Loading in Ballasted Tracks : A Computational Study.

DOT National Transportation Integrated Search

2012-04-17

This paper describes work in-progress that applies the : finite element (FE) method in predicting the responses of : individual railroad crossties to rail seat pressure loading in a : ballasted track. Both wood and prestressed concrete crossties : ar...

Ballast water as a vector of coral pathogens in the Gulf of Mexico: the case of the Cayo Arcas coral reef.

PubMed

Aguirre-Macedo, M Leopoldina; Vidal-Martinez, Victor M; Herrera-Silveira, Jorge A; Valdés-Lozano, David S; Herrera-Rodríguez, Miguel; Olvera-Novoa, Miguel A

2008-09-01

The discharge of nutrients, phytoplankton and pathogenic bacteria through ballast water may threaten the Cayo Arcas reef system. To assess this threat, the quality of ballast water and presence of coral reef pathogenic bacteria in 30 oil tankers loaded at the PEMEX Cayo Arcas crude oil terminal were determined. The water transported in the ships originated from coastal, oceanic or riverine regions. Statistical associations among quality parameters and bacteria were tested using redundancy analysis (RDA). In contrast with coastal or oceanic water, the riverine water had high concentrations of coliforms, including Vibrio cholerae 01 and, Serratia marcescens and Sphingomona spp., which are frequently associated with "white pox" and "white plague type II" coral diseases. There were also high nutrient concentrations and low water quality index values (WQI and TRIX). The presence of V. cholerae 01 highlights the need for testing ballast water coming from endemic regions into Mexican ports.

An Environmental Technology Verification (ETV) Testing of a Ballast Exchange Assurance Meter (BEAM) 100

EPA Science Inventory

Mid-ocean ballast water exchange (BWE) is mandatory for all vessels entering U.S. waters from outside the 200-mile exclusive economic zone. To support such regulation, accurate and portable verification tools are needed for determining that BWE has taken place. One parameter pr...

Per capita invasion probabilities: A linear model to predict rates of invasion via ballast water

EPA Science Inventory

Ballast water discharges are a major source of species introductions into marine, estuarine, and freshwater ecosystems. To mitigate the introduction of new invaders into these ecosystems, many agencies are proposing discharge standards that establish upper concentration limits f...

Assessment of variable fluorescence fluorometry as an approach for rapidly detecting living photoautotrophs in ballast water

NASA Astrophysics Data System (ADS)

First, Matthew R.; Robbins-Wamsley, Stephanie H.; Riley, Scott C.; Drake, Lisa A.

2018-03-01

Variable fluorescence fluorometry, an analytical approach that estimates the fluorescence yield of chlorophyll a (F0, a proximal measure of algal concentration) and photochemical yield (FV/FM, an indicator of the physiological status of algae) was evaluated as a means to rapidly assess photoautotrophs. Specifically, it was used to gauge the efficacy of ballast water treatment designed to reduce the transport and delivery of potentially invasive organisms. A phytoflagellate, Tetraselmis spp. (10-12 μm) and mixed communities of ambient protists were examined in both laboratory experiments and large-scale field trials simulating 5-d hold times in mock ballast tanks. In laboratory incubations, ambient organisms held in the dark exhibited declining F0 and FV/FM measurements relative to organisms held under lighted conditions. In field experiments, increases and decreases in F0 and FV/FM over the tank hold time corresponded to those of microscope counts of organisms in two of three trials. In the third trial, concentrations of organisms ≥ 10 and < 50 μm (presumably heterotrophic protists) increased while F0 and FV/FM decreased. Rapid and sensitive, variable fluorescence fluorometry is appropriate for detecting changes in organism concentrations and physiological status in samples dominated by microalgae. Changes in the heterotrophic community, which may become more prevalent in light-limited ballast tanks, would not be detected via variable fluorescence fluorometry, however.

Ballast system for maintaining constant pressure in a glove box

NASA Technical Reports Server (NTRS)

Shlichta, Paul J. (Inventor)

1989-01-01

A ballast system is disclosed for a glove box including a fixed platform on which is mounted an inflatable bag on top of which resides a cover and a weight. The variable gas volume of the inflatable bag communicates with that of the glove box via a valved tube. The weight and the gas volume are selected to maintain a relatively constant pressure in the glove box despite variations in the glove box volume while avoiding the use of complicated valving apparatus.

Ballast system for maintaining constant pressure in a glove box

NASA Astrophysics Data System (ADS)

Shlichta, Paul J.

1989-09-01

A ballast system is disclosed for a glove box including a fixed platform on which is mounted an inflatable bag on top of which resides a cover and a weight. The variable gas volume of the inflatable bag communicates with that of the glove box via a valved tube. The weight and the gas volume are selected to maintain a relatively constant pressure in the glove box despite variations in the glove box volume while avoiding the use of complicated valving apparatus.

Electrochemical disinfection of simulated ballast water on PbO2/graphite felt electrode.

PubMed

Chen, Shuiping; Hu, Weidong; Hong, Jianxun; Sandoe, Steve

2016-04-15

A novel PbO2/graphite felt electrode was constructed by electrochemical deposition of PbO2 on graphite felt and characterized by X-ray powder diffraction (XRD) and scanning electron microscopy (SEM) analysis. The prepared electrode is a viable technology for inactivation of Escherichia coli, Enterococcus faecalis, and Artemia salina as indicator organisms in simulated ballast water treatment, which meets the International Maritime Organization (IMO) Regulation D-2. The effects of contact time and current density on inactivation were investigated. An increase in current density generally had a beneficial effect on the inactivation of the three species. E.faecalis and A.salina were more resistant to electrochemical disinfection than E. coli. The complete disinfection of E.coli was achieved in <8min at an applied current density of 253A/m(2). Complete inactivation of E. faecalis and A.salina was achieved at the same current density after 60 and 40min of contact time, respectively. A. salina inactivation follows first-order kinetics. Copyright © 2016 Elsevier Ltd. All rights reserved.

Light Sources and Ballast Circuits

NASA Astrophysics Data System (ADS)

Yorifuji, Takashi; Sakai, Makoto; Yasuda, Takeo; Maehara, Akiyoshi; Okada, Atsunori; Gouriki, Takeshi; Mannami, Tomoaki

discharge models were reported. Further, studies on ultra high-pressure mercury lamps as light sources for projectors are becoming the mainstream of HID lamp related researches. For high-pressure sodium lamps, many studies on plant growing and pest control utilizing low insect attracting aspects were also reported in 2006. Additionally, for discharge lamps, the minimum sustaining electric power for arc tubes employed in electrode-less compact fluorescent lamps was investigated. For Hg-free rare-gas fluorescent lamps, a luminance of 10,000cd/m2 was attained by a 1 meter-long external duplex spiral electrode prototype using Xe/Ne barrier discharge. As to startup circuits, the commercialization of energy saving and high value added products mainly associated with fluorescent lamps and HID lamps are becoming common. Further, the miniaturization of startup circuits for self electronic-ballasted lamps has advanced. Speaking of the overall light sources and startup circuits in 2006 and with the enforcement of RoHS in Europe in July, the momentum toward hazardous substance-free and energy saving initiatives has been enhanced from the perspective of protecting the global environment. It is anticipated that similar restrictions will be globally enforced in the future.

Availability and Efficacy of Ballast Water Treatment Technology: Background and Issue Paper

DTIC Science & Technology

2010-06-01

transiting the Great Lakes- implications for HAB invasions. Harmful Algae , 6, 519-530. Dobroski, N., Scianni, C., Gehringer, D., & Falkner M.. 2009a. 2009...538. Drake, L., Doblin, M., & Dobbs, F. 2007. Potential microbial bioinvasions via ships’ ballast water, sediment, and biofilm . Marine Pollution...water biocides against vegetative microalgae, dinoflagellate cysts and bacteria. Harmful Algae , 6, 567-584. Gregg. M., Rigby, G., & Hallegraeff

THE DEVELOPMENT OF A SHIP BALLAST WATER TREATMENT TECHNOLOGY VERIFICATION PROTOCOL THROUGH AN INTERAGENCY AGREEMENT PARTNERSHIP

EPA Science Inventory

The introduction of nonindigenous aquatic nuisance species through the discharge of shipboard ballast water into coastal areas around the world has profound negative impacts on aquatic ecosystems worldwide. Aquatic nuisance species are one of the most important environmental issu...

Ballast Water Treatment, U.S. Great Lakes Bulk Carrier Engineering and Cost Study. Volume 2: Analysis of On-Board Treatment Methods, Alternative Ballast Water Management Practices, and Implementation Costs

DTIC Science & Technology

2013-11-01

flushing filter, disinfection with injected chlorine dioxide (chlorine dioxide is generated onboard from two component chemicals, sulfuric acid...Management System 400 80 250-8000 (10000) Sulfuric Acid and Purate for ClO2 generation Yes 0.005-0.028 8-18 Decreased sediment, potential corrosion...feed chemicals, Purate and sulfuric acid. 5. Operational and Maintenance Cost: Estimated operating and maintenance cost is $80/1000 m3 of ballast

Per capita invasion probabilities: A linear model to predict rates of invasion via ballast water

EPA Science Inventory

Ballast water discharges are a major source of species introductions into marine, estuarine, and freshwater ecosystems. For example, in the San Francisco Estuary, dubbed the “most invaded estuary in the world”, it is estimated to account for 38-76% of the aquatic invaders. To pre...

Algae viability over time in a ballast water sample

NASA Astrophysics Data System (ADS)

Gollasch, Stephan; David, Matej

2018-03-01

The biology of vessels' ballast water needs to be analysed for several reasons, one of these being performance tests of ballast water management systems. This analysis includes a viability assessment of phytoplankton. To overcome logistical problems to get algae sample processing gear on board of a vessel to document algae viability, samples may be transported to land-based laboratories. Concerns were raised how the storage conditions of the sample may impact algae viability over time and what the most appropriate storage conditions were. Here we answer these questions with a long-term algae viability study with daily sample analysis using Pulse-Amplitude Modulated (PAM) fluorometry. The sample was analysed over 79 days. We tested different storage conditions: fridge and room temperature with and without light. It seems that during the first two weeks of the experiment the viability remains almost unchanged with a slight downwards trend. In the continuing period, before the sample was split, a slightly stronger downwards viability trend was observed, which occurred at a similar rate towards the end of the experiment. After the sample was split, the strongest viability reduction was measured for the sample stored without light at room temperature. We concluded that the storage conditions, especially regarding temperature and light exposure, have a stronger impact on algae viability compared to the storage duration and that inappropriate storage conditions reduce algal viability. A sample storage time of up to two weeks in a dark and cool environment has little influence on the organism viability. This indicates that a two week time duration between sample taking on board a vessel and the viability measurement in a land-based laboratory may not be very critical.

10 CFR Appendix A to Subpart S of... - Compliance Statement for Metal Halide Lamp Ballasts

Code of Federal Regulations, 2011 CFR

2011-01-01

... Equipment: Metal Halide Lamp Ballasts Manufacturer's or Private Labeler's Name and Address: [Company name] (“the company”) submits this Compliance Statement under 10 CFR Part 431 (Energy Efficiency Program for... Reports submitted by or on behalf of this company. All information in such Certification Report(s) and in...

Detection of UV-treatment effects on plankton by rapid analytic tools for ballast water compliance monitoring immediately following treatment

NASA Astrophysics Data System (ADS)

Bradie, Johanna; Gianoli, Claudio; He, Jianjun; Lo Curto, Alberto; Stehouwer, Peter; Veldhuis, Marcel; Welschmeyer, Nick; Younan, Lawrence; Zaake, André; Bailey, Sarah

2018-03-01

Non-indigenous species seriously threaten native biodiversity. To reduce establishments, the International Maritime Organization established the Convention for the Control and Management of Ships' Ballast Water and Sediments which limits organism concentrations at discharge under regulation D-2. Most ships will comply by using on-board treatment systems to disinfect their ballast water. Port state control officers will need simple, rapid methods to detect compliance. Appropriate monitoring methods may be dependent on treatment type, since different treatments will affect organisms by a variety of mechanisms. Many indicative tools have been developed, but must be examined to ensure the measured variable is an appropriate signal for the response of the organisms to the applied treatment. We assessed the abilities of multiple analytic tools to rapidly detect the effects of a ballast water treatment system based on UV disinfection. All devices detected a large decrease in the concentrations of vital organisms ≥ 50 μm and organisms < 10 μm (mean 82.7-99.7% decrease across devices), but results were more variable for the ≥ 10 to < 50 μm size class (mean 9.0-99.9% decrease across devices). Results confirm the necessity to choose tools capable of detecting the damage inflicted on living organisms, as examined herein for UV-C treatment systems.

Tiny Stowaways: Analyzing the Economic Benefits of a U.S. Environmental Protection Agency Permit Regulating Ballast Water Discharges

NASA Astrophysics Data System (ADS)

Lovell, Sabrina J.; Drake, Lisa A.

2009-03-01

The U.S. Environmental Protection Agency has proposed permitting ballast water discharges—a benefit of which would be to reduce the economic damages associated with the introduction and spread of aquatic invasive species. Research on ship-borne aquatic invasive species has been conducted in earnest for decades, but determining the economic damages they cause remains troublesome. Furthermore, with the exception of harmful algal blooms, the economic consequences of microscopic invaders have not been studied, despite their potentially great negative effects. In this paper, we show how to estimate the economic benefits of preventing the introduction and spread of harmful bacteria, microalgae, and viruses delivered in U.S. waters. Our calculations of net social welfare show the damages from a localized incident, cholera-causing bacteria found in shellfish in the Gulf of Mexico, to be approximately 706,000 (2006). On a larger scale, harmful algal species have the potential to be transported in ships’ ballast tanks, and their effects in the United States have been to reduce commercial fisheries landings and impair water quality. We examine the economic repercussions of one bloom-forming species. Finally, we consider the possible translocation within the Great Lakes of a virus that has the potential to harm commercial and recreational fisheries. These calculations illustrate an approach to quantifying the benefits of preventing invasive aquatic microorganisms from controls on ballast water discharges.

Tiny stowaways: analyzing the economic benefits of a U.S. Environmental Protection Agency permit regulating ballast water discharges.

PubMed

Lovell, Sabrina J; Drake, Lisa A

2009-03-01

The U.S. Environmental Protection Agency has proposed permitting ballast water discharges--a benefit of which would be to reduce the economic damages associated with the introduction and spread of aquatic invasive species. Research on ship-borne aquatic invasive species has been conducted in earnest for decades, but determining the economic damages they cause remains troublesome. Furthermore, with the exception of harmful algal blooms, the economic consequences of microscopic invaders have not been studied, despite their potentially great negative effects. In this paper, we show how to estimate the economic benefits of preventing the introduction and spread of harmful bacteria, microalgae, and viruses delivered in U.S. waters. Our calculations of net social welfare show the damages from a localized incident, cholera-causing bacteria found in shellfish in the Gulf of Mexico, to be approximately $706,000 (2006$). On a larger scale, harmful algal species have the potential to be transported in ships' ballast tanks, and their effects in the United States have been to reduce commercial fisheries landings and impair water quality. We examine the economic repercussions of one bloom-forming species. Finally, we consider the possible translocation within the Great Lakes of a virus that has the potential to harm commercial and recreational fisheries. These calculations illustrate an approach to quantifying the benefits of preventing invasive aquatic microorganisms from controls on ballast water discharges.

Shipboard testing of the efficacy of SeaKleen as a ballast water treatment to eliminate non-indigenous species aboard a working tanker in Pacific waters.

PubMed

Wright, D A; Dawson, R; Caceres, V; Orano-Dawson, C E; Kananen, G E; Cutler, S J; Cutler, H G

2009-08-01

Trials were conducted aboard the tanker Seabulk Mariner to test a natural product, SeaKleen, as a biocide controlling non-indigenous populations of plankton and bacteria in ballast water. SeaKleen was dosed into matched ballast tanks at two different concentrations, 0.8 mg L(-1) active ingredient (a.i.) and 1.6 mg L(-1) a.i. during ballasting off the Oregon coast during a three-day passage to Prince William Sound, Alaska. Live organism counts from treated ballast water were compared with those from untreated (control tank) water collected from the same source location. Shipboard chemical analyses were made to verify dose and quantify chemical degradation and residuals following dilution. Results indicated that both SeaKleen doses resulted in complete zooplankton and phytoplankton mortality and that the higher dose (1.6 mg L(-1) a.i.) caused a two-log removal of culturable bacteria over a 92 h grow-out period. Spectrophotometry confirmed initial dosing to within 5% of nominal values. Shipboard bioassays were conducted using larval fish (Cyprinodon variegatus), brine shrimp (Artemia salina) and the bioluminescent dinoflagellate Pyrocystis lunula. Exposure of the test organisms to water drawn from treated ballast tanks 48 h after SeaKleen was added to the tanks resulted in 100% mortalities in Cyprinodon and Pyrocystis at both doses. Corresponding mortalities for Artemia larvae were 100% and 60% for high and low SeaKleen doses, respectively. Toxicity testing of treated water, subjected to varying dilutions, indicated that residual toxicity to even the most sensitive organisms would be eliminated once the discharge had dispersed beyond 100 feet from the vessel.

Lightweight, self-ballasting photovoltaic roofing assembly

DOEpatents

Dinwoodie, T.L.

1998-05-05

A photovoltaic roofing assembly comprises a roofing membrane (102), a plurality of photovoltaic modules (104, 106, 108) disposed as a layer on top of the roofing membrane (102), and a plurality of pre-formed spacers, pedestals or supports (112, 114, 116, 118, 120, 122) which are respectively disposed below the plurality of photovoltaic modules (104, 106, 108) and integral therewith, or fixed thereto. Spacers (112, 114, 116, 118, 120, 122) are disposed on top of roofing membrane (102). Membrane (102) is supported on conventional roof framing, and attached thereto by conventional methods. In an alternative embodiment, the roofing assembly may have insulation block (322) below the spacers (314, 314', 315, 315'). The geometry of the preformed spacers (112, 114, 116, 118, 120, 122, 314, 314', 315, 315') is such that wind tunnel testing has shown its maximum effectiveness in reducing net forces of wind uplift on the overall assembly. Such construction results in a simple, lightweight, self-ballasting, readily assembled roofing assembly which resists the forces of wind uplift using no roofing penetrations.

Lightweight, self-ballasting photovoltaic roofing assembly

DOEpatents

Dinwoodie, Thomas L.

1998-01-01

A photovoltaic roofing assembly comprises a roofing membrane (102), a plurality of photovoltaic modules (104, 106, 108) disposed as a layer on top of the roofing membrane (102), and a plurality of pre-formed spacers, pedestals or supports (112, 114, 116, 118, 120, 122) which are respectively disposed below the plurality of photovoltaic modules (104, 106, 108) and integral therewith, or fixed thereto. Spacers (112, 114, 116, 118, 120, 122) are disposed on top of roofing membrane (102). Membrane (102) is supported on conventional roof framing, and attached thereto by conventional methods. In an alternative embodiment, the roofing assembly may have insulation block (322) below the spacers (314, 314', 315, 315'). The geometry of the preformed spacers (112, 114, 116, 118, 120, 122, 314, 314', 315, 315') is such that wind tunnel testing has shown its maximum effectiveness in reducing net forces of wind uplift on the overall assembly. Such construction results in a simple, lightweight, self-ballasting, readily assembled roofing assembly which resists the forces of wind uplift using no roofing penetrations.

Lightweight, self-ballasting photovoltaic roofing assembly

DOEpatents

Dinwoodie, Thomas L.

2006-02-28

A photovoltaic roofing assembly comprises a roofing membrane (102), a plurality of photovoltaic modules (104, 106, 108) disposed as a layer on top of the roofing membrane (102), and a plurality of pre-formed spacers, pedestals or supports (112, 114, 116, 118, 120, 122) which are respectively disposed below the plurality of photovoltaic modules (104, 106, 108) and integral therewith, or fixed thereto. Spacers (112, 114, 116, 118, 120, 122) are disposed on top of roofing membrane (102). Membrane (102) is supported on conventional roof framing, and attached thereto by conventional methods. In an alternative embodiment, the roofing assembly may have insulation block (322) below the spacers (314, 314', 315, 315'). The geometry of the pre-formed spacers (112, 114, 116, 118, 120, 122, 314, 314', 315, 315') is such that wind tunnel testing has shown its maximum effectiveness in reducing net forces of wind uplift on the overall assembly. Such construction results in a simple, lightweight, self-ballasting, readily assembled roofing assembly which resists the forces of wind uplift using no roofing penetrations.

Potential ballast water transfer of organisms from the west to the east coast of India: Insights through on board sampling

NASA Astrophysics Data System (ADS)

Desai, Dattesh V.; Narale, Dhiraj; Khandeparker, Lidita; Anil, Arga Chandrashekar

2018-03-01

The possibility of translocation of organisms via ship's ballast water (BW) during a voyage from Hazira on the west coast to Visakhapatnam on the east coast of India was assessed. Samples of BW during the voyage and discharge and sediment collected subsequent to discharge of BW were collected and analyzed for different abiotic and biotic components. It was observed that the salinity did not change, whereas temperature and pH of BW increased marginally during the voyage. A marginal increase in the dissolved oxygen is observed during rough-very rough sea conditions. A sharp decline in the phytoplankton and zooplankton abundance observed in the initial ballast tank sample compared to natural seawater indicates the impact of ballast water pumping on the plankton community. Changes in the sea state during the voyage (slight-moderate to rough-very rough) resulted in a higher sediment suspension rate and suspended particulate matter and this coincided with higher bacterial abundance followed by increase in phytoplankton. An increase in the phytoplankton abundance in the discharge water could be attributed to the inoculum from the sediment. The abundance of zooplankton decreased from the start till the end of the voyage, with high numbers of dead zooplankton in the discharge sample.

Data on metals (Zn, Al, Sr, and Co) and metalloid (As) concentration levels of ballast water in commercial ships entering Bushehr port, along the Persian Gulf.

PubMed

Soleimani, Farshid; Dobaradaran, Sina; Hayati, Abdolreza; Khorsand, Maryam; Keshtkar, Mozhgan

2016-12-01

In this article, we determined the concentration levels of metals including Zn, Al, Sr, and Co and metalloid of As of ballast water in commercial ships entering Bushehr port, along the Persian Gulf. Ballast water samples were taken from commercial ships entering Bushehr port from 34 ports around the world during 15 February and 25 August 2016. The concentration levels of metals and metalloid were determined by using a graphite furnace absorption spectrometer (AAS).

Linking science and policy to prevent the spread of invasive species from the ballast water discharge of ships

EPA Science Inventory

Huamn activites are causing the global redistribution of species at a historically unprecedented rates. In marine environments, a major vector of nonindigenous species introduction is commercial shipping, including the ballast water of ocean going vessels. The introduction of n...

33 CFR 157.10 - Segregated ballast tanks and crude oil washing systems for certain new vessels.

Code of Federal Regulations, 2010 CFR

2010-07-01

... MARINE ENVIRONMENT RELATING TO TANK VESSELS CARRYING OIL IN BULK Design, Equipment, and Installation § 157.10 Segregated ballast tanks and crude oil washing systems for certain new vessels. (a) This...) Each tank vessel under this section of 20,000 DWT or more that carries crude oil must have a crude oil...

Per capita invasion probabilities: A linear model to predict rates of invasion via ballast water - 10/10

EPA Science Inventory

Ballast water discharges are a major source of species introductions into marine, estuarine, and freshwater ecosystems. For example, in the San Francisco Estuary, dubbed the “most invaded estuary in the world”, it is estimated to account for 38-76% of the aquatic invaders. To pre...

49 CFR 1242.15 - Roadway, tunnels and subways, bridges and culverts, ties, rails, other track material, ballast...

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 9 2010-10-01 2010-10-01 false Roadway, tunnels and subways, bridges and culverts, ties, rails, other track material, ballast, track laying and surfacing, and road property damaged... RAILROADS 1 Operating Expenses-Way and Structures § 1242.15 Roadway, tunnels and subways, bridges and...

On board short-time high temperature heat treatment of ballast water: a field trial under operational conditions.

PubMed

Quilez-Badia, Gemma; McCollin, Tracy; Josefsen, Kjell D; Vourdachas, Anthony; Gill, Margaret E; Mesbahi, Ehsan; Frid, Chris L J

2008-01-01

A ballast water short-time high temperature heat treatment technique was applied on board a car-carrier during a voyage from Egypt to Belgium. Ballast water from three tanks was subjected for a few seconds to temperatures ranging from 55 degrees C to 80 degrees C. The water was heated using the vessel's heat exchanger steam and a second heat exchanger was used to pre-heat and cool down the water. The treatment was effective at causing mortality of bacteria, phytoplankton and zooplankton. The International Maritime Organization (IMO) standard was not agreed before this study was carried out, but comparing our results gives a broad indication that the IMO standard would have been met in some of the tests for the zooplankton, in all the tests for the phytoplankton; and probably on most occasions for the bacteria. Passing the water through the pump increased the kill rate but increasing the temperature above 55 degrees C did not improve the heat treatment's efficacy.

Experimental settlement and dynamic behavior of a portion of ballasted railway track under high speed trains

NASA Astrophysics Data System (ADS)

Al Shaer, A.; Duhamel, D.; Sab, K.; Foret, G.; Schmitt, L.

2008-09-01

The study of railway tracks under high speed trains is one of the most important researches in the domain of transport. A reduced scale experiment with three sleepers is presented to study the dynamic behavior and the settlement of ballasted tracks. A large number of trains passing at high speeds are simulated by signals, applied with the help of hydraulic jacks, having the shape of the letter M and representing the passages of bogies on sleepers. This experiment offers results such as displacements, accelerations, pressures and settlements that allow to better understand the dynamic behavior of a portion of a ballasted railway track at reduced scale and to estimate the settlement versus the number of load cycles. It was found that mechanical properties such as the global stiffness of the track can have important variations during the experiment. The settlement was also found to be a function of the acceleration of sleepers and above all it was observed, for accelerations above a critical value, that the increase of settlement per cycle was very high.

Amplicon-Based Pyrosequencing Reveals High Diversity of Protistan Parasites in Ships' Ballast Water: Implications for Biogeography and Infectious Diseases.

PubMed

Pagenkopp Lohan, K M; Fleischer, R C; Carney, K J; Holzer, K K; Ruiz, G M

2016-04-01

Ships' ballast water (BW) commonly moves macroorganisms and microorganisms across the world's oceans and along coasts; however, the majority of these microbial transfers have gone undetected. We applied high-throughput sequencing methods to identify microbial eukaryotes, specifically emphasizing the protistan parasites, in ships' BW collected from vessels calling to the Chesapeake Bay (Virginia and Maryland, USA) from European and Eastern Canadian ports. We utilized tagged-amplicon 454 pyrosequencing with two general primer sets, amplifying either the V4 or V9 domain of the small subunit (SSU) of the ribosomal RNA (rRNA) gene complex, from total DNA extracted from water samples collected from the ballast tanks of bulk cargo vessels. We detected a diverse group of protistan taxa, with some known to contain important parasites in marine systems, including Apicomplexa (unidentified apicomplexans, unidentified gregarines, Cryptosporidium spp.), Dinophyta (Blastodinium spp., Euduboscquella sp., unidentified syndinids, Karlodinium spp., Syndinium spp.), Perkinsea (Parvilucifera sp.), Opisthokonta (Ichthyosporea sp., Pseudoperkinsidae, unidentified ichthyosporeans), and Stramenopiles (Labyrinthulomycetes). Further characterization of groups with parasitic taxa, consisting of phylogenetic analyses for four taxa (Cryptosporidium spp., Parvilucifera spp., Labyrinthulomycetes, and Ichthyosporea), revealed that sequences were obtained from both known and novel lineages. This study demonstrates that high-throughput sequencing is a viable and sensitive method for detecting parasitic protists when present and transported in the ballast water of ships. These data also underscore the potential importance of human-aided dispersal in the biogeography of these microbes and emerging diseases in the world's oceans.

Inactivation characteristics of ozone and electrolysis process for ballast water treatment using B. subtilis spores as a probe.

PubMed

Jung, Youmi; Yoon, Yeojoon; Hong, Eunkyung; Kwon, Minhwan; Kang, Joon-Wun

2013-07-15

Since ballast water affects the ocean ecosystem, the International Maritime Organization (IMO) sets a standard for ballast water management and might impose much tighter regulations in the future. The aim of this study is to evaluate the inactivation efficiency of ozonation, electrolysis, and an ozonation-electrolysis combined process, using B. subtilis spores. In seawater ozonation, HOBr is the key active substance for inactivation, because of rapid reactivity of ozone with Br(-) in seawater. In seawater electrolysis, it is also HOBr, but not HOCl, because of the rapid reaction of HOCl with Br(-), which has not been recognized carefully, even though many electrolysis technologies have been approved by the IMO. Inactivation pattern was different in ozonation and electrolysis, which has some limitations with the tailing or lag-phase, respectively. However, each deficiency can be overcome with a combined process, which is most effective as a sequential application of ozonation followed by electrolysis. Copyright © 2013 Elsevier Ltd. All rights reserved.

Enumerating Sparse Organisms in Ships’ Ballast Water: Why Counting to 10 Is Not So Easy

PubMed Central

2011-01-01

To reduce ballast water-borne aquatic invasions worldwide, the International Maritime Organization and United States Coast Guard have each proposed discharge standards specifying maximum concentrations of living biota that may be released in ships’ ballast water (BW), but these regulations still lack guidance for standardized type approval and compliance testing of treatment systems. Verifying whether BW meets a discharge standard poses significant challenges. Properly treated BW will contain extremely sparse numbers of live organisms, and robust estimates of rare events require extensive sampling efforts. A balance of analytical rigor and practicality is essential to determine the volume of BW that can be reasonably sampled and processed, yet yield accurate live counts. We applied statistical modeling to a range of sample volumes, plankton concentrations, and regulatory scenarios (i.e., levels of type I and type II errors), and calculated the statistical power of each combination to detect noncompliant discharge concentrations. The model expressly addresses the roles of sampling error, BW volume, and burden of proof on the detection of noncompliant discharges in order to establish a rigorous lower limit of sampling volume. The potential effects of recovery errors (i.e., incomplete recovery and detection of live biota) in relation to sample volume are also discussed. PMID:21434685

Enumerating sparse organisms in ships' ballast water: why counting to 10 is not so easy.

PubMed

Miller, A Whitman; Frazier, Melanie; Smith, George E; Perry, Elgin S; Ruiz, Gregory M; Tamburri, Mario N

2011-04-15

To reduce ballast water-borne aquatic invasions worldwide, the International Maritime Organization and United States Coast Guard have each proposed discharge standards specifying maximum concentrations of living biota that may be released in ships' ballast water (BW), but these regulations still lack guidance for standardized type approval and compliance testing of treatment systems. Verifying whether BW meets a discharge standard poses significant challenges. Properly treated BW will contain extremely sparse numbers of live organisms, and robust estimates of rare events require extensive sampling efforts. A balance of analytical rigor and practicality is essential to determine the volume of BW that can be reasonably sampled and processed, yet yield accurate live counts. We applied statistical modeling to a range of sample volumes, plankton concentrations, and regulatory scenarios (i.e., levels of type I and type II errors), and calculated the statistical power of each combination to detect noncompliant discharge concentrations. The model expressly addresses the roles of sampling error, BW volume, and burden of proof on the detection of noncompliant discharges in order to establish a rigorous lower limit of sampling volume. The potential effects of recovery errors (i.e., incomplete recovery and detection of live biota) in relation to sample volume are also discussed.

Eco-geomorphic processes that maintain a small coral reef island: Ballast Island in the Ryukyu Islands, Japan

NASA Astrophysics Data System (ADS)

Kayanne, Hajime; Aoki, Kenji; Suzuki, Takuya; Hongo, Chuki; Yamano, Hiroya; Ide, Yoichi; Iwatsuka, Yuudai; Takahashi, Kenya; Katayama, Hiroyuki; Sekimoto, Tsunehiro; Isobe, Masahiko

2016-10-01

Landform changes in Ballast Island, a small coral reef island in the Ryukyu Islands, were investigated by remote sensing analysis and a field survey. The area of the island almost doubled after a mass coral bleaching event in 1998. Coral branches generated by the mass mortality and broken by waves were delivered and stocked on a reef flat and accumulated to expand the area of the island. In 2012 high waves generated by typhoons also changed the island's topography. Overall, the island moved in the downdrift direction of the higher waves. Waves impacting both sides of the island piled up a large volume of coral gravels above the high-tide level. Eco-geomorphic processes, including a supply of calcareous materials from the corals on the same reef especially during stormy wave conditions, were key factors in maintaining the dynamic topographic features of this small coral reef island.

33 CFR 157.43 - Discharges of clean and segregated ballast: Seagoing tank vessels of 150 gross tons or more.

Code of Federal Regulations, 2014 CFR

2014-07-01

... an approved oil discharge monitoring and control system or, if discharged before the required oil... mixture in the ballast. Use of an oil discharge monitoring and control system is not required. This... OF THE MARINE ENVIRONMENT RELATING TO TANK VESSELS CARRYING OIL IN BULK Vessel Operation § 157.43...

33 CFR 157.43 - Discharges of clean and segregated ballast: Seagoing tank vessels of 150 gross tons or more.

Code of Federal Regulations, 2013 CFR

2013-07-01

... an approved oil discharge monitoring and control system or, if discharged before the required oil... mixture in the ballast. Use of an oil discharge monitoring and control system is not required. This... OF THE MARINE ENVIRONMENT RELATING TO TANK VESSELS CARRYING OIL IN BULK Vessel Operation § 157.43...

33 CFR 157.43 - Discharges of clean and segregated ballast: Seagoing tank vessels of 150 gross tons or more.

Code of Federal Regulations, 2010 CFR

2010-07-01

... an approved oil discharge monitoring and control system or, if discharged before the required oil... mixture in the ballast. Use of an oil discharge monitoring and control system is not required. This... OF THE MARINE ENVIRONMENT RELATING TO TANK VESSELS CARRYING OIL IN BULK Vessel Operation § 157.43...

33 CFR 157.43 - Discharges of clean and segregated ballast: Seagoing tank vessels of 150 gross tons or more.

Code of Federal Regulations, 2012 CFR

2012-07-01

... an approved oil discharge monitoring and control system or, if discharged before the required oil... mixture in the ballast. Use of an oil discharge monitoring and control system is not required. This... OF THE MARINE ENVIRONMENT RELATING TO TANK VESSELS CARRYING OIL IN BULK Vessel Operation § 157.43...

33 CFR 157.43 - Discharges of clean and segregated ballast: Seagoing tank vessels of 150 gross tons or more.

Code of Federal Regulations, 2011 CFR

2011-07-01

... an approved oil discharge monitoring and control system or, if discharged before the required oil... mixture in the ballast. Use of an oil discharge monitoring and control system is not required. This... OF THE MARINE ENVIRONMENT RELATING TO TANK VESSELS CARRYING OIL IN BULK Vessel Operation § 157.43...

33 CFR 155.350 - Oily mixture (bilge slops)/fuel oil tank ballast water discharges on oceangoing ships of less...

Code of Federal Regulations, 2012 CFR

2012-07-01

... 33 Navigation and Navigable Waters 2 2012-07-01 2012-07-01 false Oily mixture (bilge slops)/fuel... mixture (bilge slops)/fuel oil tank ballast water discharges on oceangoing ships of less than 400 gross... to a reception facility; or (2) Has approved oily-water separating equipment for processing oily...

33 CFR 155.350 - Oily mixture (bilge slops)/fuel oil tank ballast water discharges on oceangoing ships of less...

Code of Federal Regulations, 2013 CFR

2013-07-01

... 33 Navigation and Navigable Waters 2 2013-07-01 2013-07-01 false Oily mixture (bilge slops)/fuel... mixture (bilge slops)/fuel oil tank ballast water discharges on oceangoing ships of less than 400 gross... to a reception facility; or (2) Has approved oily-water separating equipment for processing oily...

33 CFR 155.350 - Oily mixture (bilge slops)/fuel oil tank ballast water discharges on oceangoing ships of less...

Code of Federal Regulations, 2011 CFR

2011-07-01

... 33 Navigation and Navigable Waters 2 2011-07-01 2011-07-01 false Oily mixture (bilge slops)/fuel... mixture (bilge slops)/fuel oil tank ballast water discharges on oceangoing ships of less than 400 gross... to a reception facility; or (2) Has approved oily-water separating equipment for processing oily...

33 CFR 155.350 - Oily mixture (bilge slops)/fuel oil tank ballast water discharges on oceangoing ships of less...

Code of Federal Regulations, 2014 CFR

2014-07-01

... 33 Navigation and Navigable Waters 2 2014-07-01 2014-07-01 false Oily mixture (bilge slops)/fuel... mixture (bilge slops)/fuel oil tank ballast water discharges on oceangoing ships of less than 400 gross... to a reception facility; or (2) Has approved oily-water separating equipment for processing oily...

Positive semidefinite tensor factorizations of the two-electron integral matrix for low-scaling ab initio electronic structure.

PubMed

Hoy, Erik P; Mazziotti, David A

2015-08-14

Tensor factorization of the 2-electron integral matrix is a well-known technique for reducing the computational scaling of ab initio electronic structure methods toward that of Hartree-Fock and density functional theories. The simplest factorization that maintains the positive semidefinite character of the 2-electron integral matrix is the Cholesky factorization. In this paper, we introduce a family of positive semidefinite factorizations that generalize the Cholesky factorization. Using an implementation of the factorization within the parametric 2-RDM method [D. A. Mazziotti, Phys. Rev. Lett. 101, 253002 (2008)], we study several inorganic molecules, alkane chains, and potential energy curves and find that this generalized factorization retains the accuracy and size extensivity of the Cholesky factorization, even in the presence of multi-reference correlation. The generalized family of positive semidefinite factorizations has potential applications to low-scaling ab initio electronic structure methods that treat electron correlation with a computational cost approaching that of the Hartree-Fock method or density functional theory.

Molecular detection of native and invasive marine invertebrate larvae present in ballast and open water environmental samples collected in Puget Sound

USGS Publications Warehouse

Harvey, J.B.J.; Hoy, M.S.; Rodriguez, R.J.

2009-01-01

Non-native marine species have been and continue to be introduced into Puget Sound via several vectors including ship's ballast water. Some non-native species become invasive and negatively impact native species or near shore habitats. We present a new methodology for the development and testing of taxon specific PCR primers designed to assess environmental samples of ocean water for the presence of native and non-native bivalves, crustaceans and algae. The intergenic spacer regions (IGS; ITS1, ITS2 and 5.8S) of the ribosomal DNA were sequenced for adult samples of each taxon studied. We used these data along with those available in Genbank to design taxon and group specific primers and tested their stringency against artificial populations of plasmid constructs containing the entire IGS region for each of the 25 taxa in our study, respectively. Taxon and group specific primer sets were then used to detect the presence or absence of native and non-native planktonic life-history stages (propagules) from environmental samples of ballast water and plankton tow net samples collected in Puget Sound. This methodology provides an inexpensive and efficient way to test the discriminatory ability of taxon specific oligonucleotides (PCR primers) before creating molecular probes or beacons for use in molecular ecological applications such as probe hybridizations or microarray analyses. This work addresses the current need to develop molecular tools capable of diagnosing the presence of planktonic life-history stages from non-native marine species (potential invaders) in ballast water and other environmental samples. ?? 2008 Elsevier B.V.

Electron fluence correction factors for various materials in clinical electron beams.

PubMed

Olivares, M; DeBlois, F; Podgorsak, E B; Seuntjens, J P

2001-08-01

Relative to solid water, electron fluence correction factors at the depth of dose maximum in bone, lung, aluminum, and copper for nominal electron beam energies of 9 MeV and 15 MeV of the Clinac 18 accelerator have been determined experimentally and by Monte Carlo calculation. Thermoluminescent dosimeters were used to measure depth doses in these materials. The measured relative dose at dmax in the various materials versus that of solid water, when irradiated with the same number of monitor units, has been used to calculate the ratio of electron fluence for the various materials to that of solid water. The beams of the Clinac 18 were fully characterized using the EGS4/BEAM system. EGSnrc with the relativistic spin option turned on was used to optimize the primary electron energy at the exit window, and to calculate depth doses in the five phantom materials using the optimized phase-space data. Normalizing all depth doses to the dose maximum in solid water stopping power ratio corrected, measured depth doses and calculated depth doses differ by less than +/- 1% at the depth of dose maximum and by less than 4% elsewhere. Monte Carlo calculated ratios of doses in each material to dose in LiF were used to convert the TLD measurements at the dose maximum into dose at the center of the TLD in the phantom material. Fluence perturbation correction factors for a LiF TLD at the depth of dose maximum deduced from these calculations amount to less than 1% for 0.15 mm thick TLDs in low Z materials and are between 1% and 3% for TLDs in Al and Cu phantoms. Electron fluence ratios of the studied materials relative to solid water vary between 0.83+/-0.01 and 1.55+/-0.02 for materials varying in density from 0.27 g/cm3 (lung) to 8.96 g/cm3 (Cu). The difference in electron fluence ratios derived from measurements and calculations ranges from -1.6% to +0.2% at 9 MeV and from -1.9% to +0.2% at 15 MeV and is not significant at the 1sigma level. Excluding the data for Cu, electron

Modelling impulsive factors for electronics and restaurant coupons’ e-store display

NASA Astrophysics Data System (ADS)

Ariningsih, P. K.; Nainggolan, M.; Sandy, I. A.

2018-04-01

In many times, the increment of e-store visitors does not followed by sales increment. Most purchases through e-commerce are impulsive buying, however only small amount of study is available to understand impulsive factors of e-store display. This paper suggests a preliminary concept on understanding the impulsive factors in Electronics and Restaurant Coupons e-store display, which are two among few popular group products sold through e-commerce. By conducting literature study and survey, 31 attributes were identified as impulsive factors in electronics e-store display and 20 attributes were identified as impulsive factors for restaurant coupon e-store. The attributes were then grouped into comprehensive impulsive factors by factor analysis. Each group of impulsive attributes were generated into 3 factors. Accessibility Factors and Trust Factors appeared for each group products. The other factors are Internal Factors for electronics e-store and Marketing factors for restaurant coupons e-store. Structural Equation Model of the impulsive factors was developed for each type of e-store, which stated the covariance between Trust Factors and Accessibility Factors. Based on preliminary model, Internal Factor and Trust Factor are influencing impulsive buying in electronics store. Special factor for electronics e-store is Internal Factor, while for restaurant coupons e-store is Marketing Factor.

10 CFR Appendix Q to Subpart B of... - Uniform Test Method for Measuring the Energy Consumption of Fluorescent Lamp Ballasts

Code of Federal Regulations, 2014 CFR

2014-01-01

... of Fluorescent Lamp Ballasts Q Appendix Q to Subpart B of Part 430 Energy DEPARTMENT OF ENERGY ENERGY CONSERVATION ENERGY CONSERVATION PROGRAM FOR CONSUMER PRODUCTS Test Procedures Pt. 430, Subpt. B, App. Q Appendix Q to Subpart B of Part 430—Uniform Test Method for Measuring the Energy Consumption of Fluorescent...

10 CFR Appendix Q to Subpart B of... - Uniform Test Method for Measuring the Energy Consumption of Fluorescent Lamp Ballasts

Code of Federal Regulations, 2012 CFR

2012-01-01

... of Fluorescent Lamp Ballasts Q Appendix Q to Subpart B of Part 430 Energy DEPARTMENT OF ENERGY ENERGY CONSERVATION ENERGY CONSERVATION PROGRAM FOR CONSUMER PRODUCTS Test Procedures Pt. 430, Subpt. B, App. Q Appendix Q to Subpart B of Part 430—Uniform Test Method for Measuring the Energy Consumption of Fluorescent...

10 CFR Appendix Q to Subpart B of... - Uniform Test Method for Measuring the Energy Consumption of Fluorescent Lamp Ballasts

Code of Federal Regulations, 2013 CFR

2013-01-01

... of Fluorescent Lamp Ballasts Q Appendix Q to Subpart B of Part 430 Energy DEPARTMENT OF ENERGY ENERGY CONSERVATION ENERGY CONSERVATION PROGRAM FOR CONSUMER PRODUCTS Test Procedures Pt. 430, Subpt. B, App. Q Appendix Q to Subpart B of Part 430—Uniform Test Method for Measuring the Energy Consumption of Fluorescent...

10 CFR 431.324 - Uniform test method for the measurement of energy efficiency and standby mode energy consumption...

Code of Federal Regulations, 2014 CFR

2014-01-01

... extinguishing the lamp is impossible or for low-frequency electronic ballasts, the following alternative... (V), and current, using an ammeter (A) connected to the ballast in accordance with the circuit shown... ballast in accordance with the circuit shown in Figure 2. ER09MR10.006 (iii) Power Line Carrier (PLC...

10 CFR 431.324 - Uniform test method for the measurement of energy efficiency and standby mode energy consumption...

Code of Federal Regulations, 2013 CFR

2013-01-01

... extinguishing the lamp is impossible or for low-frequency electronic ballasts, the following alternative... (V), and current, using an ammeter (A) connected to the ballast in accordance with the circuit shown... ballast in accordance with the circuit shown in Figure 2. ER09MR10.006 (iii) Power Line Carrier (PLC...

10 CFR 431.324 - Uniform test method for the measurement of energy efficiency and standby mode energy consumption...

Code of Federal Regulations, 2012 CFR

2012-01-01

... extinguishing the lamp is impossible or for low-frequency electronic ballasts, the following alternative... (V), and current, using an ammeter (A) connected to the ballast in accordance with the circuit shown... ballast in accordance with the circuit shown in Figure 2. ER09MR10.006 (iii) Power Line Carrier (PLC...

Incorporation of hydrophobized mineral particles in activated sludge flocs: a way to assess ballasting efficiency.

PubMed

Defontaine, G; Thormann, J; Lartiges, B S; El Samrani, A G; Barrs, O

2005-01-01

The role of mineral surface hydrophobicity in attachment to activated sludge flocs was investigated. Fluorite and quartz particles of similar granulometry were hydrophobized by adsorbing sodium oleate and dodecylamine chloride, respectively. Mineral hydrophobicity was assessed by flotation expriments. The attachment of particles to microbial flocs was determined by optical microscopy. The results indicate that hydrophobized particles are always better incorporated within activated sludge flocs than non-coated particles. A comparison with Aquatal particles used as sludge ballast reveals that hydrophobized minerals are associated with microbial flocs to the same extent.

Conference on Ballast Water and Waste Water Treatment Aboard Ships and in Ports. Held in Bremerhaven, Germany on 11-13 June 2003

DTIC Science & Technology

2003-06-13

test guidelines. Residual PERACLEAN® OCEAN in ballast water decomposes to water, acetic acid (e.g., vinegar ) and oxygen. The half-life is in the...membrane bioreactors (Figure 1), the combination of high cell density fermentation with ultrafiltration in compact modularI plants /2/. I! I I i Figure

Effect and mechanism of a High Gradient Magnetic Separation (HGMS) and Ultraviolet (UV) composite process on the inactivation of microbes in ballast water.

PubMed

Ren, Zhijun; Zhang, Lin; Shi, Yue; Leng, Xiaodong; Shao, Jingchao

2016-07-15

The patented technology of a High Gradient Magnetic Separation (HGMS)-Ultraviolet (UV) composite process was used to treat ballast water. Staphylococcus aureus (S. aureus) was selected as the reference bacteria. After treatment by the HGMS-UV process, the concentration of S. aureus on the log 10 scale was lower than 2 at different flow rates, S. aureus suffered the most serious damage, and K(+) leakage of the bacteria was 1.73mg/L higher than separate 60min UV irradiation (1.17mg/L) and HGMS (0.12mg/L) processes. These results demonstrated that the HGMS-UV composite process was an effective approach to treat ballast water. Further, the HGMS process had synergistic action on the subsequent UV irradiation process and accelerated cell membrane damage. Meanwhile, the results of superoxide dismutase (SOD) activities of bacteria and DNA band analyses indicated that the inactivation mechanisms were different for HGMS and UV irradiation. Copyright © 2016 Elsevier Ltd. All rights reserved.

Multiconfiguration calculations of electronic isotope shift factors in Al i

NASA Astrophysics Data System (ADS)

Filippin, Livio; Beerwerth, Randolf; Ekman, Jörgen; Fritzsche, Stephan; Godefroid, Michel; Jönsson, Per

2016-12-01

The present work reports results from systematic multiconfiguration Dirac-Hartree-Fock calculations of electronic isotope shift factors for a set of transitions between low-lying levels of neutral aluminium. These electronic quantities together with observed isotope shifts between different pairs of isotopes provide the changes in mean-square charge radii of the atomic nuclei. Two computational approaches are adopted for the estimation of the mass- and field-shift factors. Within these approaches, different models for electron correlation are explored in a systematic way to determine a reliable computational strategy and to estimate theoretical error bars of the isotope shift factors.

Evaluating the combined effects of ballast water management and trade dynamics on transfers of marine organisms by ships

PubMed Central

Carney, Katharine J.; Minton, Mark S.; Holzer, Kimberly K.; Miller, A. Whitman; McCann, Linda D.; Ruiz, Gregory M.

2017-01-01

Global trade by merchant ships is a leading mechanism for the unintentional transfer of marine organisms, including non-indigenous species, to bays and estuaries worldwide. To reduce the likelihood of new invasions, ships are increasingly being required to manage their ballast water (BW) prior to discharge in coastal waters. In the United States, most overseas arrivals have been required to manage BW discharge since 2004, primarily through ballast water exchange (BWE), which flushes out ballast tanks in the open ocean (>200 miles from shore). Studies have found BWE to generally reduce the abundance of organisms, and the amount of water exchanged has been estimated at 96–100%. Despite its widespread use, the overall effect of this management strategy on net propagule supply through time has not been explored. Here, temporal changes in zooplankton concentrations and the volume of BW discharged in Chesapeake Bay, U.S. were evaluated, comparing pre-management era and post-management era time periods. Chesapeake Bay is a large port system that receives extensive BW discharge, especially from bulk cargo vessels (bulkers) that export coal overseas. For bulkers arriving from overseas, mean zooplankton concentrations of total and coastal indicator taxa in BW did not decline between pre- (1993–2000) and post management (2012–2013) eras, when controlling for season and sampling method. Moreover, bulkers discharged 21 million tonnes (82% of total for Chesapeake Bay) of overseas BW in 2013, representing a 374% increase in volume when compared to 2005. The combination of BW discharge volume and zooplankton concentration data indicates that (a) net propagule supply by bulkers has increased since BWE began in Chesapeake Bay; and (b) changes in vessel behaviour and trade have contributed strongly to this outcome. Specifically, the coal-driven increase in BW discharge volume from 2005–2013, concurrent with the onset of BWE regulations, worked to counteract intended results

Evaluating the combined effects of ballast water management and trade dynamics on transfers of marine organisms by ships.

PubMed

Carney, Katharine J; Minton, Mark S; Holzer, Kimberly K; Miller, A Whitman; McCann, Linda D; Ruiz, Gregory M

2017-01-01

Global trade by merchant ships is a leading mechanism for the unintentional transfer of marine organisms, including non-indigenous species, to bays and estuaries worldwide. To reduce the likelihood of new invasions, ships are increasingly being required to manage their ballast water (BW) prior to discharge in coastal waters. In the United States, most overseas arrivals have been required to manage BW discharge since 2004, primarily through ballast water exchange (BWE), which flushes out ballast tanks in the open ocean (>200 miles from shore). Studies have found BWE to generally reduce the abundance of organisms, and the amount of water exchanged has been estimated at 96-100%. Despite its widespread use, the overall effect of this management strategy on net propagule supply through time has not been explored. Here, temporal changes in zooplankton concentrations and the volume of BW discharged in Chesapeake Bay, U.S. were evaluated, comparing pre-management era and post-management era time periods. Chesapeake Bay is a large port system that receives extensive BW discharge, especially from bulk cargo vessels (bulkers) that export coal overseas. For bulkers arriving from overseas, mean zooplankton concentrations of total and coastal indicator taxa in BW did not decline between pre- (1993-2000) and post management (2012-2013) eras, when controlling for season and sampling method. Moreover, bulkers discharged 21 million tonnes (82% of total for Chesapeake Bay) of overseas BW in 2013, representing a 374% increase in volume when compared to 2005. The combination of BW discharge volume and zooplankton concentration data indicates that (a) net propagule supply by bulkers has increased since BWE began in Chesapeake Bay; and (b) changes in vessel behaviour and trade have contributed strongly to this outcome. Specifically, the coal-driven increase in BW discharge volume from 2005-2013, concurrent with the onset of BWE regulations, worked to counteract intended results from BW

Disinfection by-products and ecotoxicity of ballast water after oxidative treatment--results and experiences from seven years of full-scale testing of ballast water management systems.

PubMed

Delacroix, Stephanie; Vogelsang, Christian; Tobiesen, August; Liltved, Helge

2013-08-15

Since 2005, five different ballast water management systems (BWMSs) based on chlorination treatment have been tested by Norwegian Institute for Water Research (NIVA) according to guidelines from the International Maritime Organization (IMO). 25% and >50% of all the tested discharge samples exhibited acute and chronic toxic effects on algae, respectively. In most cases this toxicity was plausibly caused by a high free residual oxidant (FRO) level (>0.08 mg Cl/l). Of the 22 disinfection by-products (DBPs) that were identified in treated water at discharge, four compounds were at times found at concentrations that may pose a risk to the local aquatic environment. However, there seemed to be no clear indication that the measured DBP concentrations contributed to the observed algal toxicity. The addition of methylcellulose instead of lignin in the test water to comply with IMO requirements seemed to limit the formation of DBP. Copyright © 2013 Elsevier Ltd. All rights reserved.

Simulation experiments to elucidate variable fluorescence as a potential proxy for bulk microalgal viability from natural water, sediments and biofilms: Implication in ships ballast water management.

PubMed

Patil, Jagadish S; Anil, Arga Chandrashekar

2018-05-30

The variable fluorescence fluorometry measuring microalgal biomass (initial fluorescence - F 0 , a chl-a proxy) and photosynthetic efficiency (F v /F m ) has been suggested as a potential tool in ballast-water assessment. In ballast tank, microalgae can be found in contiguous compartments i.e., in water, sediment, and biofilms. Therefore the utility of F 0 and F v /F m depends upon proper background corrections, which is straightforward for water samples but not for sediment and biofilms. This study proposes procedures for correcting F 0 values from sediment and biofilms. Irrespective of the saturation flash protocol used on any sample types the outcome of the results from viable and non-viable microalgae will remain same. Stress experiments (continuous darkness and biocide treatments) confirm that variable fluorescence (F v ) can be used as a potential proxy for viable cells as the values were negligible for non-viable cells and increased with an increase in abundance. Through this study, the utility of F v and σ PSII (functional-absorption-cross-section of photosystem II) along with F 0 and F v /F m in providing additional information on cell-viability and algal-size group during assessment is discussed. The findings will have implications not only from the perspective of ballast water but also in testing/assays of specific interest (e.g. toxicity, water treatments, antifouling) and ecological studies involving microalgae. Copyright © 2018 Elsevier Ltd. All rights reserved.

Energy Engineering Analysis Program. Lighting Survey of Selected Buildings, Pine Bluff Arsenal, Pine Bluff, Arkansas. Volume 2A: Appendices

DTIC Science & Technology

1995-06-01

Energy efficient, 30 and 40 watt ballasts are Rapid Start, thermally protected, automatic resetting. Class P, high or low power factor as required...BALLASTS Energy efficient, 30 ana 40 watt Rapic Start, thermally protected, automatic resetting. Class P. high power factor, CEM, sound rated A. unless...BALLASTS Energy efficient, 40 Watt Rapid Start, thermally protected, automatic resetting, Class P, high power factor, CBM, sound rated A, unless

Effects of UV/Ag-TiO2/O3 advanced oxidation on unicellular green alga Dunaliella salina: implications for removal of invasive species from ballast water.

PubMed

Wu, Donghai; You, Hong; Du, Jiaxuan; Chen, Chuan; Jin, Darui

2011-01-01

The UV/Ag-TiO2/O3 process was investigated for ballast water treatment using Dunaliella salina as an indicator. Inactivation curves were obtained, and the toxicity of effluent was determined. Compared with individual unit processes using ozone or UV/Ag-TiO2, the inactivation efficiency of D. salina by the combined UV/Ag-TiO2/O3 process was enhanced. The presence of ozone caused an immediate decrease in chlorophyll a (chl-a) concentration. Inactivation efficiency and ch1-a removal efficiency were positively correlated with ozone dose and ultraviolet intensity. The initial total residual oxidant (TRO) concentration of effluent increased with increasing ozone dose, and persistence of TRO resulted in an extended period of toxicity. The results suggest that UV/Ag-TiO2/O3 has potential for ballast water treatment.

Monte Carlo based electron treatment planning and cutout output factor calculations

NASA Astrophysics Data System (ADS)

Mitrou, Ellis

Electron radiotherapy (RT) offers a number of advantages over photons. The high surface dose, combined with a rapid dose fall-off beyond the target volume presents a net increase in tumor control probability and decreases the normal tissue complication for superficial tumors. Electron treatments are normally delivered clinically without previously calculated dose distributions due to the complexity of the electron transport involved and greater error in planning accuracy. This research uses Monte Carlo (MC) methods to model clinical electron beams in order to accurately calculate electron beam dose distributions in patients as well as calculate cutout output factors, reducing the need for a clinical measurement. The present work is incorporated into a research MC calculation system: McGill Monte Carlo Treatment Planning (MMCTP) system. Measurements of PDDs, profiles and output factors in addition to 2D GAFCHROMICRTM EBT2 film measurements in heterogeneous phantoms were obtained to commission the electron beam model. The use of MC for electron TP will provide more accurate treatments and yield greater knowledge of the electron dose distribution within the patient. The calculation of output factors could invoke a clinical time saving of up to 1 hour per patient.

Is It Time for a Switch in Lighting?

ERIC Educational Resources Information Center

Bennorth, Greg

1999-01-01

Reviews new types of fluorescent lamp and electronic ballasts and their associated starting methods to explain the benefits of programmed start ballasts in today's lighting applications. Advice on when it is time to make a lighting retrofit is highlighted. (GR)

77 FR 35268 - Standards for Living Organisms in Ships' Ballast Water Discharged in U.S. Waters

Federal Register 2010, 2011, 2012, 2013, 2014

2012-06-13

...On March 23, 2012, the Coast Guard published in the Federal Register a Final Rule entitled ``Standards for Living Organisms in Ships' Ballast Water Discharged in U.S. Waters''. The rulemaking triggered new information collection requirements affecting vessel owners and their potential requests for an extension of the compliance date if they cannot practicably comply with the compliance date otherwise applicable to their vessels. This document announces that the request to revise the existing collection of information to add the new request for an extension provision has been approved by the Office of Management and Budget (OMB) and may now be enforced. The OMB control number is 1625-0069.

Formation of a spark discharge in an inhomogeneous electric field with current limitation by a large ballast Resistance

DOE Office of Scientific and Technical Information (OSTI.GOV)

Baldanov, B. B., E-mail: baibat@mail.ru

2016-01-15

Results of studies of a spark discharge initiated in argon in a point–plane electrode gap with limitation of the discharge current by a large ballast resistance are presented. It is shown that the current flowing through the plasma channel of such a low-current spark has the form of periodic pulses. It is experimentally demonstrated that, when a low-current spark transforms into a constricted glow discharge, current pulses disappear, the spatial structure of the cathode glow changes abruptly, and a brightly glowing positive plasma column forms in the gap.

A semi-empirical model for the prediction of fouling in railway ballast using GPR

NASA Astrophysics Data System (ADS)

Bianchini Ciampoli, Luca; Tosti, Fabio; Benedetto, Andrea; Alani, Amir M.; Loizos, Andreas; D'Amico, Fabrizio; Calvi, Alessandro

2016-04-01

The first step in the planning for a renewal of a railway network consists in gathering information, as effectively as possible, about the state of the railway tracks. Nowadays, this activity is mostly carried out by digging trenches at regular intervals along the whole network, to evaluate both geometrical and geotechnical properties of the railway track bed. This involves issues, mainly concerning the invasiveness of the operations, the impacts on the rail traffic, the high costs, and the low levels of significance concerning such discrete data set. Ground-penetrating radar (GPR) can represent a useful technique for overstepping these issues, as it can be directly mounted onto a train crossing the railway, and collect continuous information along the network. This study is aimed at defining an empirical model for the prediction of fouling in railway ballast, by using GPR. With this purpose, a thorough laboratory campaign was implemented within the facilities of Roma Tre University. In more details, a 1.47 m long × 1.47 m wide × 0.48 m height plexiglass framework, accounting for the domain of investigation, was laid over a perfect electric conductor, and filled up with several configuration of railway ballast and fouling material (clayey sand), thereby representing different levels of fouling. Then, the set of fouling configurations was surveyed with several GPR systems. In particular, a ground-coupled multi-channel radar (600 MHz and 1600 MHz center frequency antennas) and three air-launched radar systems (1000 MHz and 2000 MHz center frequency antennas) were employed for surveying the materials. By observing the results both in terms of time and frequency domains, interesting insights are highlighted and an empirical model, relating in particular the shape of the frequency spectrum of the signal and the percentage of fouling characterizing the surveyed material, is finally proposed. Acknowledgement The Authors thank COST, for funding the Action TU1208 "Civil

Characteristic correlation study of UV disinfection performance for ballast water treatment

NASA Astrophysics Data System (ADS)

Ba, Te; Li, Hongying; Osman, Hafiiz; Kang, Chang-Wei

2016-11-01

Characteristic correlation between ultraviolet disinfection performance and operating parameters, including ultraviolet transmittance (UVT), lamp power and water flow rate, was studied by numerical and experimental methods. A three-stage model was developed to simulate the fluid flow, UV radiation and the trajectories of microorganisms. Navier-Stokes equation with k-epsilon turbulence was solved to model the fluid flow, while discrete ordinates (DO) radiation model and discrete phase model (DPM) were used to introduce UV radiation and microorganisms trajectories into the model, respectively. The UV dose statistical distribution for the microorganisms was found to move to higher value with the increase of UVT and lamp power, but moves to lower value when the water flow rate increases. Further investigation shows that the fluence rate increases exponentially with UVT but linearly with the lamp power. The average and minimum resident time decreases linearly with the water flow rate while the maximum resident time decrease rapidly in a certain range. The current study can be used as a digital design and performance evaluation tool of the UV reactor for ballast water treatment.

CMOS based image cytometry for detection of phytoplankton in ballast water.

PubMed

Pérez, J M; Jofre, M; Martínez, P; Yáñez, M A; Catalan, V; Parker, A; Veldhuis, M; Pruneri, V

2017-02-01

We introduce an image cytometer (I-CYT) for the analysis of phytoplankton in fresh and marine water environments. A linear quantification of cell numbers was observed covering several orders of magnitude using cultures of Tetraselmis and Nannochloropsis measured by autofluorescence in a laboratory environment. We assessed the functionality of the system outside the laboratory by phytoplankton quantification of samples taken from a marine water environment (Dutch Wadden Sea, The Netherlands) and a fresh water environment (Lake Ijssel, The Netherlands). The I-CYT was also employed to study the effects of two ballast water treatment systems (BWTS), based on chlorine electrolysis and UV sterilization, with the analysis including the vitality of the phytoplankton. For comparative study and benchmarking of the I-CYT, a standard flow cytometer was used. Our results prove a limit of detection (LOD) of 10 cells/ml with an accuracy between 0.7 and 0.5 log, and a correlation of 88.29% in quantification and 96.21% in vitality, with respect to the flow cytometry results.

Power supply improvements for ballasts-low pressure mercury/argon discharge lamp for water purification

NASA Astrophysics Data System (ADS)

Bokhtache, A. Aissa; Zegaoui, A.; Djahbar, A.; Allouache, H.; Hemici, K.; Kessaissia, F. Z.; Bouchrit, M. S.; Aillerie, M.

2017-02-01

The low-pressure electrical discharges established in the mercury rare gas mixtures are the basis of many applications both in the field of lighting and for industrial applications. In order to select an efficient high frequency power supply (ECG -based PWM inverter), we present and discuss results obtained in the simulation of three kinds of power supplies delivering a 0.65 A - 50KHz sinusoidal current dedicated to power low pressure UV Mercury - Argon lamp used for effect germicide on water treatment thus allowing maximum UVC radiation at 253.7 nm. Three ballasts half-bridge configurations were compared with criteria based on resulting germicide efficiency, electrical yield and reliability, for example the quality of the sinusoidal current with reduced THD, and finally, we also considered in this analysis the final economic aspect.

Innovative Ballasted Flat Roof Solar PV Racking System

DOE Office of Scientific and Technical Information (OSTI.GOV)

Peek, Richard T.

2014-12-15

The objective of this project was to reduce the cost of racking for PV solar on flat commercial rooftops. Cost reductions would come from both labor savings and material savings related to the installation process. The rack would need to accommodate the majority of modules available on the market. Cascade Engineering has a long history of converting traditional metal type applications over to plastic. Injection molding of plastics have numerous advantages including selection of resin for the application, placing the material exactly where it is needed, designing in features that will speed up the installation process, and weight reduction ofmore » the array. A plastic rack would need to meet the requirements of UL2703, Mounting systems, mounting devices, clamping/retention devices, and ground lugs for use with flat-plate photovoltaic modules and panels. Comparing original data to the end of project racking design, racking material costs were reduced 50% and labor costs reduced 64%. The racking product accommodates all 60 and 72 cell panels on the market, meets UL2703 requirements, contributes only 1.3 pounds per square foot of weight to the array, requires little ballast to secure the array, automatically grounds the module when the module is secured, stacks/nests well for shipping/fewer lifts to the roof, provides integrated wire routing, allows water to drain on the roof, and accommodates various seismic roof connections. Project goals were achieved as noted in the original funding application.« less

Performance of a biological deoxygenation process for ships' ballast water treatment under very cold water conditions.

PubMed

de Lafontaine, Yves; Despatie, Simon-Pierre

2014-02-15

Water deoxygenation is listed among the promising on-board treatment technologies to treat ships' ballast waters to reduce the risk of species transfer. We assessed the performance of a yeast-based bioreactive deoxygenation process in very cold water (<2°C) and determined the potential toxicity of the residual treated waters. Experiments using two treatment levels (0.5% and 1% v/v) were conducted in large-volume (4.5m(3)) tanks over 19 days at mean temperature of 1.5°C. Time to hypoxia varied between 10.3 and 16 days, being slightly higher than the predicted time of 9.8 days from previous empirical relationships. Water deoxygenation was achieved when yeast density exceeded 5×10(5) viable cellsmL(-1) and variation in time to hypoxia was mainly explained by difference in yeast growth. There was no oxycline and no significant difference in yeast density over the 2-m deep water column. Results from six bioassays indicated weak toxic response of treated waters at the 1.0% level, but no potential toxic response at the 0.5% treatment level. Results confirmed that the potential application of a yeast-based deoxygenation process for treating ships' ballast waters extended over the range of water temperature typically encountered during most shipping operational conditions. Time to reach full deoxygenation may however be limiting for universal application of this treatment which should be preferably used for ships making longer voyages in cold environments. There was no evidence that biological deoxygenation at low temperature did increase toxicity risk of treated waters to impede their disposal at the time of discharge. Crown Copyright © 2013. Published by Elsevier B.V. All rights reserved.

Nuclear-polarization correction to the bound-electron g factor in heavy hydrogenlike ions.

PubMed

Nefiodov, A V; Plunien, G; Soff, G

2002-08-19

The influence of nuclear polarization on the bound-electron g factor in heavy hydrogenlike ions is investigated. Numerical calculations are performed for the K- and L-shell electrons taking into account the dominant virtual nuclear excitations. This determines the ultimate limit for tests of QED utilizing measurements of the bound-electron g factor in highly charged ions.

Jet-Suspended, Calcite-Ballasted Cyanobacterial Waterwarts in a Desert Spring

NASA Technical Reports Server (NTRS)

Pichel-Garcia, Ferran; Wade, Bman D.; Farmer, Jack D.

2002-01-01

We describe a population of colonial cyanobacteria (waterwarts) that develops as the dominant primary producer in a bottom-fed, warm spring in the Cuatro Cienegas karstic region of the Mexican Chihuahuan Desert. The centimeter-sized waterwarts were suspended within a central, conically shaped, 6-m deep well by upwelling waters. Waterwarts were built by an unicellular cyanobacterium and supported a community of epiphytic filamentous cyanobacteria and diatoms but were free of heterotrophic bacteria inside. Sequence analysis of genes revealed that this cyanobacterium is only distantly related to several strains of other unicellular teria Cyanothece, Waterwarts contained orderly arrangements of mineral made up of microcrystalline low-magnesium calcite with high levels of strontium and sulfur. Waterwarts were 95.9% (v/v) glycan, 2.8% cells, and 1.3% mineral grains and had a buoyant density of 1.034 kg/L. An analysis of the hydrological properties of the spring well and the waterwarts demonstrated that both large colony size and the presence of controlled amounts of mineral ballast are required to prevent the population from being washed out of the well. The unique hydrological characteristics of the spring have likely selected for both traits. The mechanisms by which controlled nucleation of extracellular calcite is achieved remain to be explored.

Temporal changes in phytoplankton biomass and cellular properties; implications for the IMO ballast water convention.

PubMed

de Castro, Maria Cecilia Trindade; Veldhuis, Marcel J W

2018-01-24

In the Wadden Sea, the Netherlands, and at L4 in the English Channel, UK, the size class distribution of phytoplankton was investigated with respect to the size range >10-≤50 µm identified by the IMO Ballast Water Convention. Size fractionation using 10 µm mesh filtration showed considerable size bias; 23.1% of >10 µm cells were still present in the <10 µm, but 21.8% of the smaller size cells were also retained on the mesh, resulting in an overestimated number of cells/mL by as much as a factor of 5.4. Flowcytometry measurements indicated that the phytoplankton in the size range 2-50  µm was dominated by the smaller size (<10 µm) at both sites. For the >10-≤50 µm size, these were on average 3.6% and 2% in the Wadden Sea and at L4, respectively. In terms of chlorophyll biomass, they represented 28.7% and 12%, respectively. The filtration method resulted in much higher chlorophyll values for 10-50  µm size range: 53.7% in the Wadden Sea and 38% at L4. This overestimation appears to be caused by cells in 6-10  µm size range being retained on the mesh. These findings are relevant in the context of the size class distribution based on flowcytometry and semi-quantification using chlorophyll as proxy for cell density.

Low-rank factorization of electron integral tensors and its application in electronic structure theory

DOE PAGES

Peng, Bo; Kowalski, Karol

2017-01-25

In this paper, we apply reverse Cuthill-McKee (RCM) algorithm to transform two-electron integral tensors to their block diagonal forms. By further applying Cholesky decomposition (CD) on each of the diagonal blocks, we are able to represent the high-dimensional two-electron integral tensors in terms of permutation matrices and low-rank Cholesky vectors. This representation facilitates low-rank factorizations of high-dimensional tensor contractions in post-Hartree-Fock calculations. Finally, we discuss the second-order Møller-Plesset (MP2) method and the linear coupled-cluster model with doubles (L-CCD) as examples to demonstrate the efficiency of this technique in representing the two-electron integrals in a compact form.

Low-rank factorization of electron integral tensors and its application in electronic structure theory

DOE Office of Scientific and Technical Information (OSTI.GOV)

Peng, Bo; Kowalski, Karol

In this paper, we apply reverse Cuthill-McKee (RCM) algorithm to transform two-electron integral tensors to their block diagonal forms. By further applying Cholesky decomposition (CD) on each of the diagonal blocks, we are able to represent the high-dimensional two-electron integral tensors in terms of permutation matrices and low-rank Cholesky vectors. This representation facilitates low-rank factorizations of high-dimensional tensor contractions in post-Hartree-Fock calculations. Finally, we discuss the second-order Møller-Plesset (MP2) method and the linear coupled-cluster model with doubles (L-CCD) as examples to demonstrate the efficiency of this technique in representing the two-electron integrals in a compact form.

Factors that impact nurses' use of electronic mail (e-mail).

PubMed

Hughes, J A; Pakieser, R A

1999-01-01

As electronic applications are used increasingly in healthcare, nurses are being challenged to adopt them. Electronic mail (e-mail) is an electronic tool with general as well as healthcare uses. E-mail use may be an opportunity to learn a tool that requires skills similar to those used in other applications. This study aimed to identify barriers and facilitators that impact nurses' use of e-mail in the workplace. Data for this study were gathered using focus group methodology. Content analysis identified and labeled factors into seven major categories. Specific factors identified were generally consistent with those previously described in the literature as affecting use of computers in general. However, there were several additional factors identified that were not reported in other previous studies: lack of face-to-face communication, individual writing skills, recency of any educational experience, volume of mail received, password integrity, and technical support. Findings from this study provide information for any individual involved in introducing or updating an e-mail system in a healthcare environment.

Development of an Ultrasonic Resonator for Ballast Water Disinfection

NASA Astrophysics Data System (ADS)

Osman, Hafiiz; Lim, Fannon; Lucas, Margaret; Balasubramaniam, Prakash

Ultrasonic disinfection involves the application of low-frequency acoustic energy in a water body to induce cavitation. The implosion of cavitation bubbles generates high speed microjets >1 km/s, intense shock wave >1 GPa, localized hot spots >1000 K, and free-radicals, resulting in cell rupture and death of micro-organisms and pathogens. Treatment of marine ballast water using power ultrasonics is an energy-intensive process. Compared with other physical treatment methods such as ultraviolet disinfection, ultrasonic disinfection require 2 to 3 orders of magnitude more energy to achieve similar rate of micro-organism mortality. Current technology limits the amount of acoustic energy that can be transferred per unit volume of fluid and presents challenges when it comes to high-flow applications. Significant advancements in ultrasonic processing technology are needed before ultrasound can be recognized as a viable alternative disinfection method. The ultrasonic resonator has been identified as one of the areas of improvement that can potentially contribute to the overall performance of an ultrasonic disinfection system. The present study focuses on the design of multiple-orifice resonators (MOR) for generating a well-distributed cavitation field. Results show that the MOR resonator offers significantly larger vibrational surface area to mass ratio. In addition, acoustic pressure measurements indicate that the MOR resonators are able to distribute the acoustic energy across a larger surface area, while generating 2-4 times higher pressures than existing ultrasonic probes.

Distribution of E/N and N/e/ in a cross-flow electric discharge laser. [electric field to neutral gas density and electron number density

NASA Technical Reports Server (NTRS)

Dunning, J. W., Jr.; Lancashire, R. B.; Manista, E. J.

1976-01-01

Measurements have been conducted of the effect of the convection of ions and electrons on the discharge characteristics in a large scale laser. The results are presented for one particular distribution of ballast resistance. Values of electric field, current density, input power density, ratio of electric field to neutral gas density (E/N), and electron number density were calculated on the basis of measurements of the discharge properties. In a number of graphs, the E/N ratio, current density, power density, and electron density are plotted as a function of row number (downstream position) with total discharge current and gas velocity as parameters. From the dependence of the current distribution on the total current, it appears that the electron production in the first two rows significantly affects the current flowing in the succeeding rows.

Limiting factors in atomic resolution cryo electron microscopy: No simple tricks

PubMed Central

Zhang, Xing; Zhou, Z. Hong

2013-01-01

To bring cryo electron microscopy (cryoEM) of large biological complexes to atomic resolution, several factors – in both cryoEM image acquisition and 3D reconstruction – that may be neglected at low resolution become significantly limiting. Here we present thorough analyses of four limiting factors: (a) electron-beam tilt, (b) inaccurate determination of defocus values, (c) focus gradient through particles, and (d) particularly for large particles, dynamic (multiple) scattering of electrons. We also propose strategies to cope with these factors: (a) the divergence and direction tilt components of electron-beam tilt could be reduced by maintaining parallel illumination and by using a coma-free alignment procedure, respectively. Moreover, the effect of all beam tilt components, including spiral tilt, could be eliminated by use of a spherical aberration corrector. (b) More accurate measurement of defocus value could be obtained by imaging areas adjacent to the target area at high electron dose and by measuring the image shift induced by tilting the electron beam. (c) Each known Fourier coefficient in the Fourier transform of a cryoEM image is the sum of two Fourier coefficients of the 3D structure, one on each of two curved ‘characteristic surfaces’ in 3D Fourier space. We describe a simple model-based iterative method that could recover these two Fourier coefficients on the two characteristic surfaces. (d) The effect of dynamic scattering could be corrected by deconvolution of a transfer function. These analyses and our proposed strategies offer useful guidance for future experimental designs targeting atomic resolution cryoEM reconstruction. PMID:21627992

Efficacy of pH elevation as a bactericidal strategy for treating ballast water of freight carriers.

PubMed

Starliper, Clifford E; Watten, Barnaby J; Iwanowicz, Deborah D; Green, Phyllis A; Bassett, Noel L; Adams, Cynthia R

2015-05-01

Treatment of ship ballast water with sodium hydroxide (NaOH) is one method currently being developed to minimize the risk to introduce aquatic invasive species. The bactericidal capability of sodium hydroxide was determined for 148 bacterial strains from ballast water collected in 2009 and 2010 from the M/V Indiana Harbor, a bulk-freight carrier plying the Laurentian Great Lakes, USA. Primary culture of bacteria was done using brain heart infusion agar and a developmental medium. Strains were characterized based on PCR amplification and sequencing of a portion of the 16S rRNA gene. Sequence similarities (99+ %) were determined by comparison with the National Center for Biotechnology Information (NCBI) GenBank catalog. Flavobacterium spp. were the most prevalent bacteria characterized in 2009, comprising 51.1% (24/47) of the total, and Pseudomonas spp. (62/101; 61.4%) and Brevundimonas spp. (22/101; 21.8%) were the predominate bacteria recovered in 2010; together, comprising 83.2% (84/101) of the total. Testing was done in tryptic soy broth (TSB) medium adjusted with 5 N NaOH. Growth of each strain was evaluated at pH 10.0, pH 11.0 and pH 12.0, and 4 h up to 72 h. The median cell count at 0 h for 148 cultures was 5.20 × 10(6) cfu/mL with a range 1.02 × 10(5)-1.60 × 10(8) cfu/mL. The TSB adjusted to pH 10.0 and incubation for less than 24 h was bactericidal to 52 (35.1%) strains. Growth in pH 11.0 TSB for less than 4 h was bactericidal to 131 (88.5%) strains and pH 11.0 within 12 h was bactericidal to 141 (95.3%). One strain, Bacillus horikoshii, survived the harshest treatment, pH 12.0 for 72 h.

Efficacy of pH elevation as a bactericidal strategy for treating ballast water of freight carriers

PubMed Central

Starliper, Clifford E.; Watten, Barnaby J.; Iwanowicz, Deborah D.; Green, Phyllis A.; Bassett, Noel L.; Adams, Cynthia R.

2015-01-01

Treatment of ship ballast water with sodium hydroxide (NaOH) is one method currently being developed to minimize the risk to introduce aquatic invasive species. The bactericidal capability of sodium hydroxide was determined for 148 bacterial strains from ballast water collected in 2009 and 2010 from the M/V Indiana Harbor, a bulk-freight carrier plying the Laurentian Great Lakes, USA. Primary culture of bacteria was done using brain heart infusion agar and a developmental medium. Strains were characterized based on PCR amplification and sequencing of a portion of the 16S rRNA gene. Sequence similarities (99+ %) were determined by comparison with the National Center for Biotechnology Information (NCBI) GenBank catalog. Flavobacterium spp. were the most prevalent bacteria characterized in 2009, comprising 51.1% (24/47) of the total, and Pseudomonas spp. (62/101; 61.4%) and Brevundimonas spp. (22/101; 21.8%) were the predominate bacteria recovered in 2010; together, comprising 83.2% (84/101) of the total. Testing was done in tryptic soy broth (TSB) medium adjusted with 5 N NaOH. Growth of each strain was evaluated at pH 10.0, pH 11.0 and pH 12.0, and 4 h up to 72 h. The median cell count at 0 h for 148 cultures was 5.20 × 106 cfu/mL with a range 1.02 × 105–1.60 × 108 cfu/mL. The TSB adjusted to pH 10.0 and incubation for less than 24 h was bactericidal to 52 (35.1%) strains. Growth in pH 11.0 TSB for less than 4 h was bactericidal to 131 (88.5%) strains and pH 11.0 within 12 h was bactericidal to 141 (95.3%). One strain, Bacillus horikoshii, survived the harshest treatment, pH 12.0 for 72 h. PMID:26257948

Factors That Impact Nurses’ Utilization of Electronic Mail (E-Mail).

DTIC Science & Technology

1998-05-21

of a system but did little to influence behavior. A study by Golden, Beauclair , & Sussman (1992) surveyed 200 electronic mail account holders at an...Aldine Publishing. Golden, P. A., Beauclair , R., & Sussman, L. (1992). Factors affecting electronic mail use. Computers in Human Behavior, 8, 297-311

Low-rank factorization of electron integral tensors and its application in electronic structure theory

DOE Office of Scientific and Technical Information (OSTI.GOV)

Peng, Bo; Kowalski, Karol

In this letter, we introduce the reverse Cuthill-McKee (RCM) algorithm, which is often used for the bandwidth reduction of sparse tensors, to transform the two-electron integral tensors to their block diagonal forms. By further applying the pivoted Cholesky decomposition (CD) on each of the diagonal blocks, we are able to represent the high-dimensional two-electron integral tensors in terms of permutation matrices and low-rank Cholesky vectors. This representation facilitates the low-rank factorization of the high-dimensional tensor contractions that are usually encountered in post-Hartree-Fock calculations. In this letter, we discuss the second-order Møller-Plesset (MP2) method and linear coupled- cluster model with doublesmore » (L-CCD) as two simple examples to demonstrate the efficiency of the RCM-CD technique in representing two-electron integrals in a compact form.« less

Ab initio determination of effective electron-phonon coupling factor in copper

NASA Astrophysics Data System (ADS)

Ji, Pengfei; Zhang, Yuwen

2016-04-01

The electron temperature Te dependent electron density of states g (ε), Fermi-Dirac distribution f (ε), and electron-phonon spectral function α2 F (Ω) are computed as prerequisites before achieving effective electron-phonon coupling factor Ge-ph. The obtained Ge-ph is implemented into a molecular dynamics (MD) and two-temperature model (TTM) coupled simulation of femtosecond laser heating. By monitoring temperature evolutions of electron and lattice subsystems, the result utilizing Ge-ph from ab initio calculation shows a faster decrease of Te and increase of Tl than those using Ge-ph from phenomenological treatment. The approach of calculating Ge-ph and its implementation into MD-TTM simulation is applicable to other metals.

Modeling the retention of rumen boluses for the electronic identification of goats.

PubMed

Carné, S; Caja, G; Ghirardi, J J; Salama, A A K

2011-02-01

We constructed a regression model to estimate the retention of electronic boluses in goats. With this aim, 2,482 boluses were administered to goats from dairy (Murciano-Granadina, n=1,326; French Alpine, n=381) and meat (Blanca de Rasquera, n=532) breeds. A total of 19 bolus types made of materials (ceramic, plastic tubes filled with concrete or silicone, and ballasts) differing in their specific gravity (SG) were used, thereby obtaining a wide variation in bolus features: diameter (9 to 22 mm), length (37 to 84 mm), weight (5 to 111 g), volume (2.6 to 26 mL), and SG (1.0 to 5.5). Each bolus contained a half-duplex glass encapsulated transponder (32 × 3.8mm) and was administered using adapted balling guns. Murciano-Granadina and Blanca de Rasquera goats also wore 2 visual plastic ear tags: V1 (double flag, 5.1g) and V2 (flag-button, 4.2g). No data on ear tags in French Alpine goats was available. Bolus and ear tag retention [(retained/monitored) × 100] was recorded for at least 1 yr. Dynamic reading efficiency [(dynamic reading/static reading) × 100] was also evaluated from 1,496 bolus readings. No administration incidences or apparent negative behavior or performance effects were observed for any bolus type. Static reading efficiency of retained boluses was 100%, except for the prototypes with metal ballasts, which yielded a 93.3% reading efficiency. Retention of metal-ballasted boluses was confirmed using x-ray equipment. Excluding ballasted boluses, a 99.5% dynamic reading efficiency was obtained. Ear tag losses were 6.5% for V1 and 3.7% for V2, ranging from 3.2 to 7.8% depending on ear tag type and goat breed. Bolus retention varied (0 to 100%) according to their physical features. Obtained data allowed the fitting of a logistic model of bolus retention rate according to bolus volume and weight (R(2) = 0.98); the SG was implicitly considered. Estimated weight and SG to produce medium- (15 mL) and standard-sized (22 mL) boluses for 99.95% retention rate in

Importance of Relativistic Effects and Electron Correlation in Structure Factors and Electron Density of Diphenyl Mercury and Triphenyl Bismuth.

PubMed

Bučinský, Lukáš; Jayatilaka, Dylan; Grabowsky, Simon

2016-08-25

This study investigates the possibility of detecting relativistic effects and electron correlation in single-crystal X-ray diffraction experiments using the examples of diphenyl mercury (HgPh2) and triphenyl bismuth (BiPh3). In detail, the importance of electron correlation (ECORR), relativistic effects (REL) [distinguishing between total, scalar and spin-orbit (SO) coupling relativistic effects] and picture change error (PCE) on the theoretical electron density, its topology and its Laplacian using infinite order two component (IOTC) wave functions is discussed. This is to develop an understanding of the order of magnitude and shape of these different effects as they manifest in the electron density. Subsequently, the same effects are considered for the theoretical structure factors. It becomes clear that SO and PCE are negligible, but ECORR and scalar REL are important in low- and medium-order reflections on absolute and relative scales-not in the high-order region. As a further step, Hirshfeld atom refinement (HAR) and subsequent X-ray constrained wavefunction (XCW) fitting have been performed for the compound HgPh2 with various relativistic and nonrelativistic wave functions against the experimental structure factors. IOTC calculations of theoretical structure factors and relativistic HAR as well as relativistic XCW fitting are presented for the first time, accounting for both scalar and spin-orbit relativistic effects.

Exchange enhancement of the electron g-factor in a two-dimensional semimetal in HgTe quantum wells

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bovkun, L. S., E-mail: bovkun@ipmras.ru; Krishtopenko, S. S.; Zholudev, M. S.

The exchange enhancement of the electron g-factor in perpendicular magnetic fields to 12 T in HgTe/CdHgTe quantum wells 20 nm wide with a semimetal band structure is studied. The electron effective mass and g-factor at the Fermi level are determined by analyzing the temperature dependence of the amplitude of Shubnikov–de Haas oscillation in weak fields and near odd Landau-level filling factors ν ≤ 9. The experimental values are compared with theoretical calculations performed in the one-electron approximation using the eight-band kp Hamiltonian. The found dependence of g-factor enhancement on the electron concentration is explained by changes in the contributions ofmore » hole- and electron-like states to exchange corrections to the Landau-level energies in the conduction band.« less

Dark-field transmission electron microscopy and the Debye-Waller factor of graphene

PubMed Central

Hubbard, William A.; White, E. R.; Dawson, Ben; Lodge, M. S.; Ishigami, Masa; Regan, B. C.

2014-01-01

Graphene's structure bears on both the material's electronic properties and fundamental questions about long range order in two-dimensional crystals. We present an analytic calculation of selected area electron diffraction from multi-layer graphene and compare it with data from samples prepared by chemical vapor deposition and mechanical exfoliation. A single layer scatters only 0.5% of the incident electrons, so this kinematical calculation can be considered reliable for five or fewer layers. Dark-field transmission electron micrographs of multi-layer graphene illustrate how knowledge of the diffraction peak intensities can be applied for rapid mapping of thickness, stacking, and grain boundaries. The diffraction peak intensities also depend on the mean-square displacement of atoms from their ideal lattice locations, which is parameterized by a Debye-Waller factor. We measure the Debye-Waller factor of a suspended monolayer of exfoliated graphene and find a result consistent with an estimate based on the Debye model. For laboratory-scale graphene samples, finite size effects are sufficient to stabilize the graphene lattice against melting, indicating that ripples in the third dimension are not necessary. PMID:25242882

Dark-field transmission electron microscopy and the Debye-Waller factor of graphene.

PubMed

Shevitski, Brian; Mecklenburg, Matthew; Hubbard, William A; White, E R; Dawson, Ben; Lodge, M S; Ishigami, Masa; Regan, B C

2013-01-15

Graphene's structure bears on both the material's electronic properties and fundamental questions about long range order in two-dimensional crystals. We present an analytic calculation of selected area electron diffraction from multi-layer graphene and compare it with data from samples prepared by chemical vapor deposition and mechanical exfoliation. A single layer scatters only 0.5% of the incident electrons, so this kinematical calculation can be considered reliable for five or fewer layers. Dark-field transmission electron micrographs of multi-layer graphene illustrate how knowledge of the diffraction peak intensities can be applied for rapid mapping of thickness, stacking, and grain boundaries. The diffraction peak intensities also depend on the mean-square displacement of atoms from their ideal lattice locations, which is parameterized by a Debye-Waller factor. We measure the Debye-Waller factor of a suspended monolayer of exfoliated graphene and find a result consistent with an estimate based on the Debye model. For laboratory-scale graphene samples, finite size effects are sufficient to stabilize the graphene lattice against melting, indicating that ripples in the third dimension are not necessary.

Unequal density effect on static structure factor of coupled electron layers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Saini, L. K., E-mail: lks@ashd.svnit.ac.in; Nayak, Mukesh G., E-mail: lks@ashd.svnit.ac.in

In order to understand the ordered phase, if any, in a real coupled electron layers (CEL), there is a need to take into account the effect of unequal layer density. Such phase is confirmed by a strong peak in a static structure factor. With the aid of quantum/dynamical version of Singwi, Tosi, Land and Sjölander (so-called qSTLS) approximation, we have calculated the intra- and interlayer static structure factors, S{sub ll}(q) and S{sub 12}(q), over a wide range of density parameter r{sub sl} and interlayer spacing d. In our present study, the sharp peak in S{sub 22}(q) has been found atmore » critical density with sufficiently lower interlayer spacing. Further, to find the resultant effect of unequal density on intra- and interlayer static structure factors, we have compared our results with that of the recent CEL system with equal layer density and isolated single electron layer.« less

Evaluation of induction motor performance using an electronic power factor controller

NASA Technical Reports Server (NTRS)

1978-01-01

The concept of reducing the losses in an induction motor by electronically controlling the time interval between the zero crossing of the applied voltage and the zero crossing of the armature current was evaluated. The effect on power losses and power factor of reducing the applied sinusoidal voltages below the rated value was investigated experimentally. The reduction in power losses was measured using an electronic controller designed and built at MSFC. Modifications to the MSFC controller are described as well as a manually controlled electronic device which does not require that the motor be wye connected and the neutral available. Possible energy savings are examined.

Factors Affecting Educational Innovation with in Class Electronic Response Systems

ERIC Educational Resources Information Center

Freeman, Mark; Bell, Amani; Comerton-Forde, Carole; Pickering, Joanne; Blayney, Paul

2007-01-01

This paper reports the use of Rogers' diffusion of innovation perspective to understand the factors affecting educational innovation decisions, specifically in regard to in class electronic response systems. Despite decreasing costs and four decades of research showing strong student support, academic adoption is limited. Using data collected from…

How to make the fourth revolution: Human factors in the adoption of electronic instructional aids

NASA Technical Reports Server (NTRS)

Demerath, N. J.; Daniels, L. A.

1973-01-01

The prospects and problems of getting higher education in the United States (high school and above) to more fully utilize electronic technologies are examined. Sociological, psychological, and political factors are analyzed to determine the feasibility of adopting electronic instructional techniques. Differences in organizations, attitudes, and customs of different kinds of students, teachers, administrators, and publics are crucial factors in innovation.

Size versus electronic factors in transition metal carbide and TCP phase stability

NASA Astrophysics Data System (ADS)

Pettifor, D. G.; Seiser, B.; Margine, E. R.; Kolmogorov, A. N.; Drautz, R.

2013-09-01

The contributions of atomic size and electronic factors to the structural stability of transition metal carbides and topologically close-packed (TCP) phases are investigated. The hard-sphere model that has been used by Cottrell to rationalize the occurrence of the octahedral and trigonal local coordination polyhedra within the transition metal carbides is shown to have limitations in TiC since density functional theory (DFT) predicts that the second most metastable phase closest to the B1 (NaCl) ground state takes the B? (BN) structure type with 5-atom local coordination polyhedra with very short Ti-C bond lengths. The importance of electronic factors in the TCP phases is demonstrated by DFT predictions that the A15, ? and ? phases are stabilized between groups VI and VII of the elemental transition metals, whereas the ? and Laves phases are destabilized. The origin of this difference is related to the bimodal shape parameter of the electronic density of states by using the bond-order potential expansion of the structural energy within a canonical tight-binding model. The importance of the size factor in the TCP phases is illustrated by the DFT heats of formation for the binary systems Mo-Re, Mo-Ru, Nb-Re and Nb-Ru which show that the ? and Laves phases become more and more stable compared to A15, ? and ? as the size factor increases from Mo-Re through to Nb-Ru.

High pCO2-induced exopolysaccharide-rich ballasted aggregates of planktonic cyanobacteria could explain Paleoproterozoic carbon burial.

PubMed

Kamennaya, Nina A; Zemla, Marcin; Mahoney, Laura; Chen, Liang; Holman, Elizabeth; Holman, Hoi-Ying; Auer, Manfred; Ajo-Franklin, Caroline M; Jansson, Christer

2018-05-29

The contribution of planktonic cyanobacteria to burial of organic carbon in deep-sea sediments before the emergence of eukaryotic predators ~1.5 Ga has been considered negligible owing to the slow sinking speed of their small cells. However, global, highly positive excursion in carbon isotope values of inorganic carbonates ~2.22-2.06 Ga implies massive organic matter burial that had to be linked to oceanic cyanobacteria. Here to elucidate that link, we experiment with unicellular planktonic cyanobacteria acclimated to high partial CO 2 pressure (pCO 2 ) representative of the early Paleoproterozoic. We find that high pCO 2 boosts generation of acidic extracellular polysaccharides (EPS) that adsorb Ca and Mg cations, support mineralization, and aggregate cells to form ballasted particles. The down flux of such self-assembled cyanobacterial aggregates would decouple the oxygenic photosynthesis from oxidative respiration at the ocean scale, drive export of organic matter from surface to deep ocean and sustain oxygenation of the planetary surface.

High pCO 2-induced exopolysaccharide-rich ballasted aggregates of planktonic cyanobacteria could explain Paleoproterozoic carbon burial

DOE PAGES

Kamennaya, Nina A.; Zemla, Marcin; Mahoney, Laura; ...

2018-05-29

Here, the contribution of planktonic cyanobacteria to burial of organic carbon in deep-sea sediments before the emergence of eukaryotic predators ~1.5 Ga has been considered negligible owing to the slow sinking speed of their small cells. However, global, highly positive excursion in carbon isotope values of inorganic carbonates ~2.22–2.06 Ga implies massive organic matter burial that had to be linked to oceanic cyanobacteria. Here to elucidate that link, we experiment with unicellular planktonic cyanobacteria acclimated to high partial CO 2 pressure ( pCO 2) representative of the early Paleoproterozoic. We find that high pCO 2 boosts generation of acidic extracellularmore » polysaccharides (EPS) that adsorb Ca and Mg cations, support mineralization, and aggregate cells to form ballasted particles. The down flux of such self-assembled cyanobacterial aggregates would decouple the oxygenic photosynthesis from oxidative respiration at the ocean scale, drive export of organic matter from surface to deep ocean and sustain oxygenation of the planetary surface.« less

High pCO 2-induced exopolysaccharide-rich ballasted aggregates of planktonic cyanobacteria could explain Paleoproterozoic carbon burial

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kamennaya, Nina A.; Zemla, Marcin; Mahoney, Laura

Here, the contribution of planktonic cyanobacteria to burial of organic carbon in deep-sea sediments before the emergence of eukaryotic predators ~1.5 Ga has been considered negligible owing to the slow sinking speed of their small cells. However, global, highly positive excursion in carbon isotope values of inorganic carbonates ~2.22–2.06 Ga implies massive organic matter burial that had to be linked to oceanic cyanobacteria. Here to elucidate that link, we experiment with unicellular planktonic cyanobacteria acclimated to high partial CO 2 pressure ( pCO 2) representative of the early Paleoproterozoic. We find that high pCO 2 boosts generation of acidic extracellularmore » polysaccharides (EPS) that adsorb Ca and Mg cations, support mineralization, and aggregate cells to form ballasted particles. The down flux of such self-assembled cyanobacterial aggregates would decouple the oxygenic photosynthesis from oxidative respiration at the ocean scale, drive export of organic matter from surface to deep ocean and sustain oxygenation of the planetary surface.« less

Factors that Affect Emergent Literacy Development When Engaging with Electronic Books

ERIC Educational Resources Information Center

Salmon, Lynda G.

2014-01-01

This article reviews extant literature with the purpose of identifying factors that affect the potential efficacy of electronic books to support literacy development during early childhood. Selection criteria include experimental, quasi-experimental, and observational studies from peer-reviewed journals from 2000 to 2013 with a target population…

Relationship between propagule pressure and colonization pressure in invasion ecology: a test with ships' ballast.

PubMed

Briski, Elizabeta; Bailey, Sarah A; Casas-Monroy, Oscar; DiBacco, Claudio; Kaczmarska, Irena; Levings, Colin; MacGillivary, Michael L; McKindsey, Christopher W; Nasmith, Leslie E; Parenteau, Marie; Piercey, Grace E; Rochon, André; Roy, Suzanne; Simard, Nathalie; Villac, Maria C; Weise, Andréa M; MacIsaac, Hugh J

2012-08-07

Increasing empirical evidence indicates the number of released individuals (i.e. propagule pressure) and number of released species (i.e. colonization pressure) are key determinants of the number of species that successfully invade new habitats. In view of these relationships, and the possibility that ships transport whole communities of organisms, we collected 333 ballast water and sediment samples to investigate the relationship between propagule and colonization pressure for a variety of diverse taxonomic groups (diatoms, dinoflagellates and invertebrates). We also reviewed the scientific literature to compare the number of species transported by ships to those reported in nature. Here, we show that even though ships transport nearly entire local communities, a strong relationship between propagule and colonization pressure exists only for dinoflagellates. Our study provides evidence that colonization pressure of invertebrates and diatoms may fluctuate widely irrespective of propagule pressure. We suggest that the lack of correspondence is explained by reduced uptake of invertebrates into the transport vector and the sensitivity of invertebrates and diatoms to selective pressures during transportation. Selection during transportation is initially evident through decreases in propagule pressure, followed by decreased colonization pressure in the most sensitive taxa.

Relationship between propagule pressure and colonization pressure in invasion ecology: a test with ships' ballast

PubMed Central

Briski, Elizabeta; Bailey, Sarah A.; Casas-Monroy, Oscar; DiBacco, Claudio; Kaczmarska, Irena; Levings, Colin; MacGillivary, Michael L.; McKindsey, Christopher W.; Nasmith, Leslie E.; Parenteau, Marie; Piercey, Grace E.; Rochon, André; Roy, Suzanne; Simard, Nathalie; Villac, Maria C.; Weise, Andréa M.; MacIsaac, Hugh J.

2012-01-01

Increasing empirical evidence indicates the number of released individuals (i.e. propagule pressure) and number of released species (i.e. colonization pressure) are key determinants of the number of species that successfully invade new habitats. In view of these relationships, and the possibility that ships transport whole communities of organisms, we collected 333 ballast water and sediment samples to investigate the relationship between propagule and colonization pressure for a variety of diverse taxonomic groups (diatoms, dinoflagellates and invertebrates). We also reviewed the scientific literature to compare the number of species transported by ships to those reported in nature. Here, we show that even though ships transport nearly entire local communities, a strong relationship between propagule and colonization pressure exists only for dinoflagellates. Our study provides evidence that colonization pressure of invertebrates and diatoms may fluctuate widely irrespective of propagule pressure. We suggest that the lack of correspondence is explained by reduced uptake of invertebrates into the transport vector and the sensitivity of invertebrates and diatoms to selective pressures during transportation. Selection during transportation is initially evident through decreases in propagule pressure, followed by decreased colonization pressure in the most sensitive taxa. PMID:22456877

Extracting Information about the Electronic Quality of Organic Solar-Cell Absorbers from Fill Factor and Thickness

NASA Astrophysics Data System (ADS)

Kaienburg, Pascal; Rau, Uwe; Kirchartz, Thomas

2016-08-01

Understanding the fill factor in organic solar cells remains challenging due to its complex dependence on a multitude of parameters. By means of drift-diffusion simulations, we thoroughly analyze the fill factor of such low-mobility systems and demonstrate its dependence on a collection coefficient defined in this work. We systematically discuss the effect of different recombination mechanisms, space-charge regions, and contact properties. Based on these findings, we are able to interpret the thickness dependence of the fill factor for different experimental studies from the literature. The presented model provides a facile method to extract the photoactive layer's electronic quality which is of particular importance for the fill factor. We illustrate that over the past 15 years, the electronic quality has not been continuously improved, although organic solar-cell efficiencies increased steadily over the same period of time. Only recent reports show the synthesis of polymers for semiconducting films of high electronic quality that are able to produce new efficiency records.

TU-F-CAMPUS-T-05: A Cloud-Based Monte Carlo Dose Calculation for Electron Cutout Factors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mitchell, T; Bush, K

Purpose: For electron cutouts of smaller sizes, it is necessary to verify electron cutout factors due to perturbations in electron scattering. Often, this requires a physical measurement using a small ion chamber, diode, or film. The purpose of this study is to develop a fast Monte Carlo based dose calculation framework that requires only a smart phone photograph of the cutout and specification of the SSD and energy to determine the electron cutout factor, with the ultimate goal of making this cloud-based calculation widely available to the medical physics community. Methods: The algorithm uses a pattern recognition technique to identifymore » the corners of the cutout in the photograph as shown in Figure 1. It then corrects for variations in perspective, scaling, and translation of the photograph introduced by the user’s positioning of the camera. Blob detection is used to identify the portions of the cutout which comprise the aperture and the portions which are cutout material. This information is then used define physical densities of the voxels used in the Monte Carlo dose calculation algorithm as shown in Figure 2, and select a particle source from a pre-computed library of phase-spaces scored above the cutout. The electron cutout factor is obtained by taking a ratio of the maximum dose delivered with the cutout in place to the dose delivered under calibration/reference conditions. Results: The algorithm has been shown to successfully identify all necessary features of the electron cutout to perform the calculation. Subsequent testing will be performed to compare the Monte Carlo results with a physical measurement. Conclusion: A simple, cloud-based method of calculating electron cutout factors could eliminate the need for physical measurements and substantially reduce the time required to properly assure accurate dose delivery.« less

Factors Influencing Electronic Clinical Information Exchange in Small Medical Group Practices

ERIC Educational Resources Information Center

Kralewski, John E.; Zink, Therese; Boyle, Raymond

2012-01-01

Purpose: The purpose of this study was to identify the organizational factors that influence electronic health information exchange (HIE) by medical group practices in rural areas. Methods: A purposive sample of 8 small medical group practices in 3 experimental HIE regions were interviewed to determine the extent of clinical information exchange…

Collaborating with human factors when designing an electronic textbook

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ratner, J.A.; Zadoks, R.I.; Attaway, S.W.

The development of on-line engineering textbooks presents new challenges to authors to effectively integrate text and tools in an electronic environment. By incorporating human factors principles of interface design and cognitive psychology early in the design process, a team at Sandia National Laboratories was able to make the end product more usable and shorten the prototyping and editing phases. A critical issue was simultaneous development of paper and on-line versions of the textbook. In addition, interface consistency presented difficulties with distinct goals and limitations for each media. Many of these problems were resolved swiftly with human factors input using templates,more » style guides and iterative usability testing of both paper and on-line versions. Writing style continuity was also problematic with numerous authors contributing to the text.« less

A knowledge-based taxonomy of critical factors for adopting electronic health record systems by physicians: a systematic literature review

PubMed Central

2010-01-01

Background The health care sector is an area of social and economic interest in several countries; therefore, there have been lots of efforts in the use of electronic health records. Nevertheless, there is evidence suggesting that these systems have not been adopted as it was expected, and although there are some proposals to support their adoption, the proposed support is not by means of information and communication technology which can provide automatic tools of support. The aim of this study is to identify the critical adoption factors for electronic health records by physicians and to use them as a guide to support their adoption process automatically. Methods This paper presents, based on the PRISMA statement, a systematic literature review in electronic databases with adoption studies of electronic health records published in English. Software applications that manage and process the data in the electronic health record have been considered, i.e.: computerized physician prescription, electronic medical records, and electronic capture of clinical data. Our review was conducted with the purpose of obtaining a taxonomy of the physicians main barriers for adopting electronic health records, that can be addressed by means of information and communication technology; in particular with the information technology roles of the knowledge management processes. Which take us to the question that we want to address in this work: "What are the critical adoption factors of electronic health records that can be supported by information and communication technology?". Reports from eight databases covering electronic health records adoption studies in the medical domain, in particular those focused on physicians, were analyzed. Results The review identifies two main issues: 1) a knowledge-based classification of critical factors for adopting electronic health records by physicians; and 2) the definition of a base for the design of a conceptual framework for supporting the

Monte Carlo calculations of electron beam quality conversion factors for several ion chamber types.

PubMed

Muir, B R; Rogers, D W O

2014-11-01

To provide a comprehensive investigation of electron beam reference dosimetry using Monte Carlo simulations of the response of 10 plane-parallel and 18 cylindrical ion chamber types. Specific emphasis is placed on the determination of the optimal shift of the chambers' effective point of measurement (EPOM) and beam quality conversion factors. The EGSnrc system is used for calculations of the absorbed dose to gas in ion chamber models and the absorbed dose to water as a function of depth in a water phantom on which cobalt-60 and several electron beam source models are incident. The optimal EPOM shifts of the ion chambers are determined by comparing calculations of R50 converted from I50 (calculated using ion chamber simulations in phantom) to R50 calculated using simulations of the absorbed dose to water vs depth in water. Beam quality conversion factors are determined as the calculated ratio of the absorbed dose to water to the absorbed dose to air in the ion chamber at the reference depth in a cobalt-60 beam to that in electron beams. For most plane-parallel chambers, the optimal EPOM shift is inside of the active cavity but different from the shift determined with water-equivalent scaling of the front window of the chamber. These optimal shifts for plane-parallel chambers also reduce the scatter of beam quality conversion factors, kQ, as a function of R50. The optimal shift of cylindrical chambers is found to be less than the 0.5 rcav recommended by current dosimetry protocols. In most cases, the values of the optimal shift are close to 0.3 rcav. Values of kecal are calculated and compared to those from the TG-51 protocol and differences are explained using accurate individual correction factors for a subset of ion chambers investigated. High-precision fits to beam quality conversion factors normalized to unity in a beam with R50 = 7.5 cm (kQ (')) are provided. These factors avoid the use of gradient correction factors as used in the TG-51 protocol although a

SU-F-T-67: Correction Factors for Monitor Unit Verification of Clinical Electron Beams

DOE Office of Scientific and Technical Information (OSTI.GOV)

Haywood, J

Purpose: Monitor units calculated by electron Monte Carlo treatment planning systems are often higher than TG-71 hand calculations for a majority of patients. Here I’ve calculated tables of geometry and heterogeneity correction factors for correcting electron hand calculations. Method: A flat water phantom with spherical volumes having radii ranging from 3 to 15 cm was created. The spheres were centered with respect to the flat water phantom, and all shapes shared a surface at 100 cm SSD. D{sub max} dose at 100 cm SSD was calculated for each cone and energy on the flat phantom and for the spherical volumesmore » in the absence of the flat phantom. The ratio of dose in the sphere to dose in the flat phantom defined the geometrical correction factor. The heterogeneity factors were then calculated from the unrestricted collisional stopping power for tissues encountered in electron beam treatments. These factors were then used in patient second check calculations. Patient curvature was estimated by the largest sphere that aligns to the patient contour, and appropriate tissue density was read from the physical properties provided by the CT. The resulting MU were compared to those calculated by the treatment planning system and TG-71 hand calculations. Results: The geometry and heterogeneity correction factors range from ∼(0.8–1.0) and ∼(0.9–1.01) respectively for the energies and cones presented. Percent differences for TG-71 hand calculations drop from ∼(3–14)% to ∼(0–2)%. Conclusion: Monitor units calculated with the correction factors typically decrease the percent difference to under actionable levels, < 5%. While these correction factors work for a majority of patients, there are some patient anatomies that do not fit the assumptions made. Using these factors in hand calculations is a first step in bringing the verification monitor units into agreement with the treatment planning system MU.« less

Synthesis of water suitable as the MEPC.174(58) G8 influent water for testing ballast water management systems.

PubMed

D'Agostino, Fabio; Del Core, Marianna; Cappello, Simone; Mazzola, Salvatore; Sprovieri, Mario

2015-10-01

Here, we describe the methodologies adopted to ensure that natural seawater, used as "influent water" for the land test, complies with the requirement that should be fulfilled to show the efficacy of the new ballast water treatment system (BWTS). The new BWTS was located on the coast of SW Sicily (Italy), and the sampled seawater showed that bacteria and plankton were two orders of magnitude lower than requested. Integrated approaches for preparation of massive cultures of bacteria (Alcanivorax borkumensis and Marinobacter hydrocarbonoclasticus), algae (Tetraselmis suecica), rotifers (Brachionus plicatilis), and crustaceans (Artemia salina) suitable to ensure that 200 m(3) of water fulfilled the international guidelines of MEPC.174(58)G8 are here described. These methodologies allowed us to prepare the "influent water" in good agreement with guidelines and without specific problems arising from natural conditions (seasons, weather, etc.) which significantly affect the concentrations of organisms at sea. This approach also offered the chance to reliably run land tests once every two weeks.

Factors influencing equipment selection in electron beam processing

NASA Astrophysics Data System (ADS)

Barnard, J. W.

2003-08-01

During the eighties and nineties accelerator manufacturers dramatically increased the beam power available for high-energy equipment. This effort was directed primarily at meeting the demands of the sterilization industry. During this era, the perception that bigger (higher power, higher energy) was always better prevailed since the operating and capital costs of accelerators did not increase with power and energy as fast as the throughput. High power was needed to maintain per unit costs low for treatment. This philosophy runs counter to certain present-day realities of the sterilization business as well as conditions influencing accelerator selection in other electron beam applications. Recent experience in machine selection is described and factors affecting choice are presented.

Towards a Resolution of the Proton Form Factor Problem: New Electron and Positron Scattering Data

NASA Astrophysics Data System (ADS)

Adikaram, D.; Rimal, D.; Weinstein, L. B.; Raue, B.; Khetarpal, P.; Bennett, R. P.; Arrington, J.; Brooks, W. K.; Adhikari, K. P.; Afanasev, A. V.; Amaryan, M. J.; Anderson, M. D.; Anefalos Pereira, S.; Avakian, H.; Ball, J.; Battaglieri, M.; Bedlinskiy, I.; Biselli, A. S.; Bono, J.; Boiarinov, S.; Briscoe, W. J.; Burkert, V. D.; Carman, D. S.; Careccia, S.; Celentano, A.; Chandavar, S.; Charles, G.; Colaneri, L.; Cole, P. L.; Contalbrigo, M.; Crede, V.; D'Angelo, A.; Dashyan, N.; De Vita, R.; De Sanctis, E.; Deur, A.; Djalali, C.; Dodge, G. E.; Dupre, R.; Egiyan, H.; El Alaoui, A.; El Fassi, L.; Elouadrhiri, L.; Eugenio, P.; Fedotov, G.; Fegan, S.; Filippi, A.; Fleming, J. A.; Fradi, A.; Garillon, B.; Gilfoyle, G. P.; Giovanetti, K. L.; Girod, F. X.; Goetz, J. T.; Gohn, W.; Golovatch, E.; Gothe, R. W.; Griffioen, K. A.; Guegan, B.; Guidal, M.; Guo, L.; Hafidi, K.; Hakobyan, H.; Hanretty, C.; Harrison, N.; Hattawy, M.; Hicks, K.; Holtrop, M.; Hughes, S. M.; Hyde, C. E.; Ilieva, Y.; Ireland, D. G.; Ishkhanov, B. S.; Jenkins, D.; Jiang, H.; Jo, H. S.; Joo, K.; Joosten, S.; Kalantarians, N.; Keller, D.; Khandaker, M.; Kim, A.; Kim, W.; Klein, A.; Klein, F. J.; Koirala, S.; Kubarovsky, V.; Kuhn, S. E.; Livingston, K.; Lu, H. Y.; MacGregor, I. J. D.; Markov, N.; Mattione, P.; Mayer, M.; McKinnon, B.; Mestayer, M. D.; Meyer, C. A.; Mirazita, M.; Mokeev, V.; Montgomery, R. A.; Moody, C. I.; Moutarde, H.; Movsisyan, A.; Camacho, C. Munoz; Nadel-Turonski, P.; Niccolai, S.; Niculescu, G.; Osipenko, M.; Ostrovidov, A. I.; Park, K.; Pasyuk, E.; Peña, C.; Pisano, S.; Pogorelko, O.; Price, J. W.; Procureur, S.; Prok, Y.; Protopopescu, D.; Puckett, A. J. R.; Ripani, M.; Rizzo, A.; Rosner, G.; Rossi, P.; Roy, P.; Sabatié, F.; Salgado, C.; Schott, D.; Schumacher, R. A.; Seder, E.; Sharabian, Y. G.; Simonyan, A.; Skorodumina, I.; Smith, E. S.; Smith, G. D.; Sober, D. I.; Sokhan, D.; Sparveris, N.; Stepanyan, S.; Stoler, P.; Strauch, S.; Sytnik, V.; Taiuti, M.; Tian, Ye; Trivedi, A.; Ungaro, M.; Voskanyan, H.; Voutier, E.; Walford, N. K.; Watts, D. P.; Wei, X.; Wood, M. H.; Zachariou, N.; Zana, L.; Zhang, J.; Zhao, Z. W.; Zonta, I.; CLAS Collaboration

2015-02-01

There is a significant discrepancy between the values of the proton electric form factor, GEp, extracted using unpolarized and polarized electron scattering. Calculations predict that small two-photon exchange (TPE) contributions can significantly affect the extraction of GEp from the unpolarized electron-proton cross sections. We determined the TPE contribution by measuring the ratio of positron-proton to electron-proton elastic scattering cross sections using a simultaneous, tertiary electron-positron beam incident on a liquid hydrogen target and detecting the scattered particles in the Jefferson Lab CLAS detector. This novel technique allowed us to cover a wide range in virtual photon polarization (ɛ ) and momentum transfer (Q2) simultaneously, as well as to cancel luminosity-related systematic errors. The cross section ratio increases with decreasing ɛ at Q2=1.45 GeV2 . This measurement is consistent with the size of the form factor discrepancy at Q2≈1.75 GeV2 and with hadronic calculations including nucleon and Δ intermediate states, which have been shown to resolve the discrepancy up to 2 - 3 GeV2 .

Electric field tunable electron g factor and high asymmetrical Stark effect in InAs1-xNx quantum dots

NASA Astrophysics Data System (ADS)

Zhang, X. W.; Fan, W. J.; Li, S. S.; Xia, J. B.

2007-04-01

The electronic structure, electron g factor, and Stark effect of InAs1-xNx quantum dots are studied by using the ten-band k •p model. It is found that the g factor can be tuned to be zero by the shape and size of quantum dots, nitrogen (N) doping, and the electric field. The N doping has two effects on the g factor: the direct effect increases the g factor and the indirect effect decreases it. The Stark effect in quantum ellipsoids is high asymmetrical and the asymmetry factor may be 319.

A survey-based study of factors that motivate nurses to protect the privacy of electronic medical records.

PubMed

Ma, Chen-Chung; Kuo, Kuang-Ming; Alexander, Judith W

2016-02-02

The purpose of this study is to investigate factors that motivate nurses to protect privacy in electronic medical records, based on the Decomposed Theory of Planned Behavior. This cross-sectional study used questionnaires to collect data from nurses in a large tertiary care military hospital in Taiwan. The three hundred two (302) valid questionnaires returned resulted in a response rate of 63.7 %. Structural equation modeling identified that the factors of attitude, subjective norm, and perceived behavioral control of the nurses significantly predicted the nurses' intention to protect the privacy of electronic medical records. Further, perceived usefulness and compatibility, peer and superior influence, self-efficacy and facilitating conditions, respectively predicted these three factors. The results of our study may provide valuable information for education and practice in predicting nurses' intention to protect privacy of electronic medical records.

Identification and Progression of Heart Disease Risk Factors in Diabetic Patients from Longitudinal Electronic Health Records.

PubMed

Jonnagaddala, Jitendra; Liaw, Siaw-Teng; Ray, Pradeep; Kumar, Manish; Dai, Hong-Jie; Hsu, Chien-Yeh

2015-01-01

Heart disease is the leading cause of death worldwide. Therefore, assessing the risk of its occurrence is a crucial step in predicting serious cardiac events. Identifying heart disease risk factors and tracking their progression is a preliminary step in heart disease risk assessment. A large number of studies have reported the use of risk factor data collected prospectively. Electronic health record systems are a great resource of the required risk factor data. Unfortunately, most of the valuable information on risk factor data is buried in the form of unstructured clinical notes in electronic health records. In this study, we present an information extraction system to extract related information on heart disease risk factors from unstructured clinical notes using a hybrid approach. The hybrid approach employs both machine learning and rule-based clinical text mining techniques. The developed system achieved an overall microaveraged F-score of 0.8302.

Towards a Resolution of the Proton Form Factor Problem: New Electron and Positron Scattering Data

DOE Office of Scientific and Technical Information (OSTI.GOV)

Adikaram, D.; Rimal, D.; Weinstein, L. B.

There is a significant discrepancy between the values of the proton electric form factor, GpE, extracted using unpolarized and polarized electron scattering. Calculations predict that small two-photon exchange (TPE) contributions can significantly affect the extraction of GpE from the unpolarized electron-proton cross sections. We determined the TPE contribution by measuring the ratio of positron-proton to electron-proton elastic scattering cross sections using a simultaneous, tertiary electron-positron beam incident on a liquid hydrogen target and detecting the scattered particles in the Jefferson Lab CLAS detector. This novel technique allowed us to cover a wide range in virtual photon polarization (epsilon) and momentummore » transfer (Q2) simultaneously, as well as to cancel luminosity-related systematic errors. The cross section ratio increases with decreasing ε at Q2=1.45 GeV2. This measurement is consistent with the size of the form factor discrepancy at Q2≈1.75 GeV2 and with hadronic calculations including nucleon and Delta intermediate states, which have been shown to resolve the discrepancy up to 2-3 GeV2.« less

Towards a Resolution of the Proton Form Factor Problem: New Electron and Positron Scattering Data

DOE PAGES

Adikaram, D.; Rimal, D.; Weinstein, L. B.; ...

2015-02-10

There is a significant discrepancy between the values of the proton electric form factor, GpE, extracted using unpolarized and polarized electron scattering. Calculations predict that small two-photon exchange (TPE) contributions can significantly affect the extraction of GpE from the unpolarized electron-proton cross sections. We determined the TPE contribution by measuring the ratio of positron-proton to electron-proton elastic scattering cross sections using a simultaneous, tertiary electron-positron beam incident on a liquid hydrogen target and detecting the scattered particles in the Jefferson Lab CLAS detector. This novel technique allowed us to cover a wide range in virtual photon polarization (epsilon) and momentummore » transfer (Q2) simultaneously, as well as to cancel luminosity-related systematic errors. The cross section ratio increases with decreasing ε at Q2=1.45 GeV2. This measurement is consistent with the size of the form factor discrepancy at Q2≈1.75 GeV2 and with hadronic calculations including nucleon and Delta intermediate states, which have been shown to resolve the discrepancy up to 2-3 GeV2.« less

Towards a resolution of the proton form factor problem: new electron and positron scattering data.

PubMed

Adikaram, D; Rimal, D; Weinstein, L B; Raue, B; Khetarpal, P; Bennett, R P; Arrington, J; Brooks, W K; Adhikari, K P; Afanasev, A V; Amaryan, M J; Anderson, M D; Anefalos Pereira, S; Avakian, H; Ball, J; Battaglieri, M; Bedlinskiy, I; Biselli, A S; Bono, J; Boiarinov, S; Briscoe, W J; Burkert, V D; Carman, D S; Careccia, S; Celentano, A; Chandavar, S; Charles, G; Colaneri, L; Cole, P L; Contalbrigo, M; Crede, V; D'Angelo, A; Dashyan, N; De Vita, R; De Sanctis, E; Deur, A; Djalali, C; Dodge, G E; Dupre, R; Egiyan, H; El Alaoui, A; El Fassi, L; Elouadrhiri, L; Eugenio, P; Fedotov, G; Fegan, S; Filippi, A; Fleming, J A; Fradi, A; Garillon, B; Gilfoyle, G P; Giovanetti, K L; Girod, F X; Goetz, J T; Gohn, W; Golovatch, E; Gothe, R W; Griffioen, K A; Guegan, B; Guidal, M; Guo, L; Hafidi, K; Hakobyan, H; Hanretty, C; Harrison, N; Hattawy, M; Hicks, K; Holtrop, M; Hughes, S M; Hyde, C E; Ilieva, Y; Ireland, D G; Ishkhanov, B S; Jenkins, D; Jiang, H; Jo, H S; Joo, K; Joosten, S; Kalantarians, N; Keller, D; Khandaker, M; Kim, A; Kim, W; Klein, A; Klein, F J; Koirala, S; Kubarovsky, V; Kuhn, S E; Livingston, K; Lu, H Y; MacGregor, I J D; Markov, N; Mattione, P; Mayer, M; McKinnon, B; Mestayer, M D; Meyer, C A; Mirazita, M; Mokeev, V; Montgomery, R A; Moody, C I; Moutarde, H; Movsisyan, A; Camacho, C Munoz; Nadel-Turonski, P; Niccolai, S; Niculescu, G; Osipenko, M; Ostrovidov, A I; Park, K; Pasyuk, E; Peña, C; Pisano, S; Pogorelko, O; Price, J W; Procureur, S; Prok, Y; Protopopescu, D; Puckett, A J R; Ripani, M; Rizzo, A; Rosner, G; Rossi, P; Roy, P; Sabatié, F; Salgado, C; Schott, D; Schumacher, R A; Seder, E; Sharabian, Y G; Simonyan, A; Skorodumina, I; Smith, E S; Smith, G D; Sober, D I; Sokhan, D; Sparveris, N; Stepanyan, S; Stoler, P; Strauch, S; Sytnik, V; Taiuti, M; Tian, Ye; Trivedi, A; Ungaro, M; Voskanyan, H; Voutier, E; Walford, N K; Watts, D P; Wei, X; Wood, M H; Zachariou, N; Zana, L; Zhang, J; Zhao, Z W; Zonta, I

2015-02-13

There is a significant discrepancy between the values of the proton electric form factor, G(E)(p), extracted using unpolarized and polarized electron scattering. Calculations predict that small two-photon exchange (TPE) contributions can significantly affect the extraction of G(E)(p) from the unpolarized electron-proton cross sections. We determined the TPE contribution by measuring the ratio of positron-proton to electron-proton elastic scattering cross sections using a simultaneous, tertiary electron-positron beam incident on a liquid hydrogen target and detecting the scattered particles in the Jefferson Lab CLAS detector. This novel technique allowed us to cover a wide range in virtual photon polarization (ϵ) and momentum transfer (Q(2)) simultaneously, as well as to cancel luminosity-related systematic errors. The cross section ratio increases with decreasing ϵ at Q(2)=1.45  GeV(2). This measurement is consistent with the size of the form factor discrepancy at Q(2)≈1.75  GeV(2) and with hadronic calculations including nucleon and Δ intermediate states, which have been shown to resolve the discrepancy up to 2-3  GeV(2).

The occurrence of pathogenic bacteria in some ships' ballast water incoming from various marine regions to the Sea of Marmara, Turkey.

PubMed

Altug, Gulsen; Gurun, Sevan; Cardak, Mine; Ciftci, Pelin S; Kalkan, Samet

2012-10-01

The composition and frequency of antibiotic resistance of pathogenic bacteria, the abundance of heterotrophic aerobic bacteria (HPC) and possible in-situ use of chromogenic agar were investigated in the ships' ballast water coming from different regions of the world to the Sea of Marmara, Turkey for the first time. The samples that were taken from 21 unit ships coming from various marine environments of the Southern China Sea, the Atlantic Ocean, the Mediterranean and the Black Sea to the Sea of Marmara, Turkey in 2009 and 2010 were tested. 38 bacteria species, 27 of them pathogenic bacteria belonging to 17 familia, were detected. Vibrio cholera was not detected in the samples. However, the presence of a high number of HPC, including a cocktail of pathogenic bacteria showed that the ships carry a potential risk for the Sea of Marmara. Copyright © 2012 Elsevier Ltd. All rights reserved.

Computational Thermochemistry: Scale Factor Databases and Scale Factors for Vibrational Frequencies Obtained from Electronic Model Chemistries.

PubMed

Alecu, I M; Zheng, Jingjing; Zhao, Yan; Truhlar, Donald G

2010-09-14

Optimized scale factors for calculating vibrational harmonic and fundamental frequencies and zero-point energies have been determined for 145 electronic model chemistries, including 119 based on approximate functionals depending on occupied orbitals, 19 based on single-level wave function theory, three based on the neglect-of-diatomic-differential-overlap, two based on doubly hybrid density functional theory, and two based on multicoefficient correlation methods. Forty of the scale factors are obtained from large databases, which are also used to derive two universal scale factor ratios that can be used to interconvert between scale factors optimized for various properties, enabling the derivation of three key scale factors at the effort of optimizing only one of them. A reduced scale factor optimization model is formulated in order to further reduce the cost of optimizing scale factors, and the reduced model is illustrated by using it to obtain 105 additional scale factors. Using root-mean-square errors from the values in the large databases, we find that scaling reduces errors in zero-point energies by a factor of 2.3 and errors in fundamental vibrational frequencies by a factor of 3.0, but it reduces errors in harmonic vibrational frequencies by only a factor of 1.3. It is shown that, upon scaling, the balanced multicoefficient correlation method based on coupled cluster theory with single and double excitations (BMC-CCSD) can lead to very accurate predictions of vibrational frequencies. With a polarized, minimally augmented basis set, the density functionals with zero-point energy scale factors closest to unity are MPWLYP1M (1.009), τHCTHhyb (0.989), BB95 (1.012), BLYP (1.013), BP86 (1.014), B3LYP (0.986), MPW3LYP (0.986), and VSXC (0.986).

Finite-nuclear-size contribution to the g factor of a bound electron: Higher-order effects

NASA Astrophysics Data System (ADS)

Karshenboim, Savely G.; Ivanov, Vladimir G.

2018-02-01

A precision comparison of theory and experiments on the g factor of an electron bound in a hydrogenlike ion with a spinless nucleus requires a detailed account of finite-nuclear-size contributions. While the relativistic corrections to the leading finite-size contribution are known, the higher-order effects need an additional consideration. Two results are presented in the paper. One is on the anomalous-magnetic-moment correction to the finite-size effects and the other is due to higher-order effects in Z α m RN . We also present here a method to relate the contributions to the g factor of a bound electron in a hydrogenlike atom to its energy within a nonrelativistic approach.

Measurements of output factors with different detector types and Monte Carlo calculations of stopping-power ratios for degraded electron beams.

PubMed

Björk, Peter; Knöös, Tommy; Nilsson, Per

2004-10-07

The aim of the present study was to investigate three different detector types (a parallel-plate ionization chamber, a p-type silicon diode and a diamond detector) with regard to output factor measurements in degraded electron beams, such as those encountered in small-electron-field radiotherapy and intraoperative radiation therapy (IORT). The Monte Carlo method was used to calculate mass collision stopping-power ratios between water and the different detector materials for these complex electron beams (nominal energies of 6, 12 and 20 MeV). The diamond detector was shown to exhibit excellent properties for output factor measurements in degraded beams and was therefore used as a reference. The diode detector was found to be well suited for practical measurements of output factors, although the water-to-silicon stopping-power ratio was shown to vary slightly with treatment set-up and irradiation depth (especially for lower electron energies). Application of ionization-chamber-based dosimetry, according to international dosimetry protocols, will introduce uncertainties smaller than 0.3% into the output factor determination for conventional IORT beams if the variation of the water-to-air stopping-power ratio is not taken into account. The IORT system at our department includes a 0.3 cm thin plastic scatterer inside the therapeutic beam, which furthermore increases the energy degradation of the electrons. By ignoring the change in the water-to-air stopping-power ratio due to this scatterer, the output factor could be underestimated by up to 1.3%. This was verified by the measurements. In small-electron-beam dosimetry, the water-to-air stopping-power ratio variation with field size could mostly be ignored. For fields with flat lateral dose profiles (>3 x 3 cm2), output factors determined with the ionization chamber were found to be in close agreement with the results of the diamond detector. For smaller field sizes the lateral extension of the ionization chamber hampers

Capstone 3 electronic flight bag (EFB) - airport moving map operational evaluation : human factors report

DOT National Transportation Integrated Search

2013-05-30

This report documents the human factors activities conducted as part of the Capstone 3 Electronic Flight Bag (EFB) Airport Moving Map operational evaluation. The purpose of that operational evaluation was to understand the safety implications of ...

Electron Flux Dropouts at L ˜ 4.2 From Global Positioning System Satellites: Occurrences, Magnitudes, and Main Driving Factors

NASA Astrophysics Data System (ADS)

Boynton, R. J.; Mourenas, D.; Balikhin, M. A.

2017-11-01

Dropouts in electron fluxes at L ˜ 4.2 were investigated for a broad range of energies from 120 keV to 10 MeV, using 16 years of electron flux data from Combined X-ray Dosimeter on board Global Positioning System (GPS) satellites. Dropouts were defined as flux decreases by at least a factor 4 in 12 h, or 24 h during which a decrease by at least a factor of 1.5 must occur during each 12 h time bin. Such fast and strong dropouts were automatically identified from the GPS electron flux data and statistics of dropout magnitudes, and occurrences were compiled as a function of electron energy. Moreover, the Error Reduction Ratio analysis was employed to search for nonlinear relationships between electron flux dropouts and various solar wind and geomagnetic activity indices, in order to identify potential external causes of dropouts. At L ˜ 4.2, the main driving factor for the more numerous and stronger 1-10 MeV electron dropouts turns out to be the southward interplanetary magnetic field Bs, suggesting an important effect from precipitation loss due to combined electromagnetic ion cyclotron and whistler mode waves in a significant fraction of these events, supplementing magnetopause shadowing and outward radial diffusion which are also effective at lower energies.

Risk factors for medication errors in the electronic and manual prescription.

PubMed

Volpe, Cris Renata Grou; Melo, Eveline Maria Magalhães de; Aguiar, Lucas Barbosa de; Pinho, Diana Lúcia Moura; Stival, Marina Morato

2016-08-08

to compare electronic and manual prescriptions of a public hospital of Brasilia, identifying risk factors for the occurrence of medication errors. descriptive-exploratory, comparative and retrospective study. Data collection occurred from July 2012 to January 2013, using an instrument for the review of the information contained in medical records related to the medication process. A total of 190 manual and 199 electronic records composed the sample, with 2027 prescriptions each. compared to the manual prescription, a significant reduction was observed in the risk factors after implantation of the electronic prescription, in items such as "lack of the form of dilution" (71.1% to 22.3%) and "prescription with brand name" (99.5% to 31.5%). Conversely, the risk factors "no check" and "lack of CRM of the prescriber" increased. The lack of the allergy registration and the occurrences related to medication were the same for both groups. generally, the use of the electronic prescription system was associated with a significant reduction in risk factors for medication errors, concerning the following aspects: illegibility, prescription with brand name and presence of essential items that provide a safe and effective prescription. comparar as prescrições eletrônicas e manuais de um hospital público do Distrito Federal, identificando os fatores de risco para ocorrência de erros de medicação. Estudo descritivo-exploratório, comparativo e retrospectivo. A coleta de dados ocorreu no período de julho de 2012 a janeiro de 2013, através de instrumento para revisão das informações referentes ao processo de medicação contidas em prontuários. Integraram a amostra 190 prontuários manuais e 199 eletrônicos, com 2027 prescrições cada. na comparação com a prescrição manual, observou-se redução significativa dos fatores de risco após implantação da eletrônica, em itens como "falta da forma de diluição" (71,1% e 22,3%) e "prescrição com nome comercial" (99

DC power limitation of the heterojunction bipolar transistor with dot geometry: Effect of base potential distribution on thermal runaway

NASA Astrophysics Data System (ADS)

Liou, L. L.; Jenkins, T.; Huang, C. I.

1997-06-01

The d.c. power limitation of a conventional HBT with dot geometry was studied theoretically using combined electro-thermal and transmission line models. In most cases, the thermal runaway occurs at a power level lower than that set by the intrinsic electronic property of the device. The dependence of the d.c. thermal runaway threshold power density, Pmax, on the emitter dot radius and emitter ballast resistance was calculated. Increasing emitter dot radius lowers Pmax. Although ballast resistance increases Pmax, the effect reduces as the emitter dot radius increases. This is caused by the non-uniform potential distribution in the base layer. When thermal runaway is considered, the nonuniform base-emitter potential offsets the improvement of the power handling capability by the physical ballast resistance. Conventional HBTs with a large radius (greater than 4 μm) exhibit a small Pmax caused by thermal effect. This threshold power density can be increased drastically by using the thermal shunt technique.

[Associated factors to availability and use of electronic media in children from preschool to 4th grade].

PubMed

Camargo, Diana Marina; Orozco, Luis Carlos

2013-01-01

The increased availability of electronic media has changed the behavior in children and young people by encouraging sedentary lifestile, with health effects from a very young age. To characterize the availability and use of electronic media and its associated factors in children from preschool through 4 th grade. A cross-sectional study with cluster sampling was carried out. Parents filled out the demographic survey, the availability and use of electronic media at home and in the child´s room. Log-binomial regression models were applied to estimate prevalence ratios adjusted for the sampling. Seven hundred and ten parents answered. The average age of the children was 6.7 years and 49.7% were male. Factors such as the mother working out of the house and family income were positively associated with the availability of electronic media at home and in the child´s room. The availability of a TV, computer and console in the child´s room, contributes to longer use of these electronic media. Both, the male gender and age of the child, were positively associated with the availability and use of electronic media. This is the first study in Colombia that reports the availability and use of electronic media in children. It is clear that modern life encourages sedentary behavior from the earliest years of life, which has been associated with health problems from early childhood. Intervention studies are needed aimed at reducing these behaviors in our context.

Effectiveness of early identification and electronic interventions for teens with risk factors for the development of heart disease and diabetes.

PubMed

Webber, Pam; Marsh, Wallace; Jung, Lorena; Gardiner, Mary; James, Jasmine; McMullan, Pam

2016-01-01

Serum risk factors for the development of heart disease and diabetes are not routinely evaluated in teens. The intent of this study was to determine the prevalence of these risk factors in teens and evaluate the effectiveness of a two-part electronic education program (recurring electronic lifestyle education program [REEP]) on reducing risks. Teens (n = 170) were recruited from one urban and one rural high school in the mid-Atlantic in 2014. Following baseline data collection in February, REEP was initiated and data collection repeated at 12 weeks. Data were analyzed and students sent a report with results and recommendations. One or more serum and/or physical risk factors were found in the majority of students with low vitamin D and elevated body mass index (BMI) being the most common. Correlations existed between elevated BMI and elevated diastolic blood pressure, low vitamin D, and low high-density lipoprotein. All but one risk factor (BMI) improved at 12 weeks. The majority of teens had one or more physical and/or serum risk factors. Using multiple electronic methods to deliver healthy lifestyle recommendations helps lower these risks. Also, Blackboard, an electronic learning platform, was found to be an effective data management and communication center. ©2015 American Association of Nurse Practitioners.

Factors affecting willingness to share electronic health data among California consumers.

PubMed

Kim, Katherine K; Sankar, Pamela; Wilson, Machelle D; Haynes, Sarah C

2017-04-04

Robust technology infrastructure is needed to enable learning health care systems to improve quality, access, and cost. Such infrastructure relies on the trust and confidence of individuals to share their health data for healthcare and research. Few studies have addressed consumers' views on electronic data sharing and fewer still have explored the dual purposes of healthcare and research together. The objective of the study is to explore factors that affect consumers' willingness to share electronic health information for healthcare and research. This study involved a random-digit dial telephone survey of 800 adult Californians conducted in English and Spanish. Logistic regression was performed using backward selection to test for significant (p-value ≤ 0.05) associations of each explanatory variable with the outcome variable. The odds of consent for electronic data sharing for healthcare decreased as Likert scale ratings for EHR impact on privacy worsened, odds ratio (OR) = 0.74, 95% CI [0.60, 0.90]; security, OR = 0.80, 95% CI [0.66, 0.98]; and quality, OR = 0.59, 95% CI [0.46-0.75]. The odds of consent for sharing for research was greater for those who think EHR will improve research quality, OR = 11.26, 95% CI [4.13, 30.73]; those who value research benefit over privacy OR = 2.72, 95% CI [1.55, 4.78]; and those who value control over research benefit OR = 0.49, 95% CI [0.26, 0.94]. Consumers' choices about electronically sharing health information are affected by their attitudes toward EHRs as well as beliefs about research benefit and individual control. Design of person-centered interventions utilizing electronically collected health information, and policies regarding data sharing should address these values of importance to people. Understanding of these perspectives is critical for leveraging health data to support learning health care systems.

The advanced EctoSys electrolysis as an integral part of a ballast water treatment system.

PubMed

Echardt, J; Kornmueller, A

2009-01-01

A full-scale 500 m(3)/h ballast water treatment system was tested according to the landbased type approval procedure of the International Maritime Organization (IMO). The system consists of disc filters followed by the advanced EctoSys electrolysis as an integral part for disinfection. The test water quality exceeded by far the minimum requirements for type approval testing. Due to the properties of the special electrodes used together with the striking disinfection effect, the disinfectants assumed to be produced inline by the EctoSys cell in river water were hydroxyl radicals, while in brackish water additionally chlorine and consequently the more stable bromine were formed. In river water, no residual oxidants could be detected in accordance with the assumed production of not responding, highly-reactive and short-living hydroxyl radicals. Accordingly, disinfection byproduct (DBP) formation was very low and close to the limit of quantification in river water. While in brackish water, initial residual oxidant concentrations were maximum 2 mg/L as chlorine and mostly brominated DBP (especially bromoform and bromate) were found. Overall considering this worst case test approach, the DBP concentrations of the treated effluents were below or in the range of the WHO Drinking Water Guideline values and therefore evaluated as acceptable for discharge to the environment. The stringent discharge standard by IMO concerning viable organisms was fully met in river and brackish water, proving the disinfection efficiency of the EctoSys electrolysis against smaller plankton and bacteria.

Computational thermochemistry: Automated generation of scale factors for vibrational frequencies calculated by electronic structure model chemistries

NASA Astrophysics Data System (ADS)

Yu, Haoyu S.; Fiedler, Lucas J.; Alecu, I. M.; Truhlar, Donald G.

2017-01-01

We present a Python program, FREQ, for calculating the optimal scale factors for calculating harmonic vibrational frequencies, fundamental vibrational frequencies, and zero-point vibrational energies from electronic structure calculations. The program utilizes a previously published scale factor optimization model (Alecu et al., 2010) to efficiently obtain all three scale factors from a set of computed vibrational harmonic frequencies. In order to obtain the three scale factors, the user only needs to provide zero-point energies of 15 or 6 selected molecules. If the user has access to the Gaussian 09 or Gaussian 03 program, we provide the option for the user to run the program by entering the keywords for a certain method and basis set in the Gaussian 09 or Gaussian 03 program. Four other Python programs, input.py, input6, pbs.py, and pbs6.py, are also provided for generating Gaussian 09 or Gaussian 03 input and PBS files. The program can also be used with data from any other electronic structure package. A manual of how to use this program is included in the code package.

Adapting Wireless Technology to Lighting Control and Environmental Sensing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dana Teasdale; Francis Rubinstein; Dave Watson

The high cost of retrofitting buildings with advanced lighting control systems is a barrier to adoption of this energy-saving technology. Wireless technology, however, offers a solution to mounting installation costs since it requires no additional wiring to implement. To demonstrate the feasibility of such a system, a prototype wirelessly-controlled advanced lighting system was designed and built. The system includes the following components: a wirelessly-controllable analog circuit module (ACM), a wirelessly-controllable electronic dimmable ballast, a T8 3-lamp fixture, an environmental multi-sensor, a current transducer, and control software. The ACM, dimmable ballast, multi-sensor, and current transducer were all integrated with SmartMesh{trademark} wirelessmore » mesh networking nodes, called motes, enabling wireless communication, sensor monitoring, and actuator control. Each mote-enabled device has a reliable communication path to the SmartMesh Manager, a single board computer that controls network functions and connects the wireless network to a PC running lighting control software. The ACM is capable of locally driving one or more standard 0-10 Volt electronic dimmable ballasts through relay control and a 0-10 Volt controllable output. The mote-integrated electronic dimmable ballast is designed to drive a standard 3-lamp T8 light fixture. The environmental multi-sensor measures occupancy, light level and temperature. The current transducer is used to measure the power consumed by the fixture. Control software was developed to implement advanced lighting algorithms, including daylight ramping, occupancy control, and demand response. Engineering prototypes of each component were fabricated and tested in a bench-scale system. Based on standard industry practices, a cost analysis was conducted. It is estimated that the installation cost of a wireless advanced lighting control system for a retrofit application is at least 30% lower than a comparable wired

High-precision measurement of the electron spin g factor of trapped atomic nitrogen in the endohedral fullerene N@C60

NASA Astrophysics Data System (ADS)

Wittmann, J. J.; Can, T. V.; Eckardt, M.; Harneit, W.; Griffin, R. G.; Corzilius, B.

2018-05-01

The electronic g factor carries highly useful information about the electronic structure of a paramagnetic species, such as spin-orbit coupling and dia- or paramagnetic (de-)shielding due to local fields of surrounding electron pairs. However, in many cases, a near "spin-only" case is observed, in particular for light elements, necessitating accurate and precise measurement of the g factors. Such measurement is typically impeded by a "chicken and egg situation": internal or external reference standards are used for relative comparison of electron paramagnetic resonance (EPR) Larmor frequencies. However, the g factor of the standard itself usually is subject to a significant uncertainty which directly limits the precision and/or accuracy of the sought after sample g factor. Here, we apply an EPR reference-free approach for determining the g factor of atomic nitrogen trapped within the endohedral fullerene C60:N@C60 in its polycrystalline state by measuring the 1H NMR resonance frequency of dispersing toluene at room temperature. We found a value of g = 2.00204 (4) with a finally reached relative precision of ∼20 ppm. This accurate measurement allows us to directly compare the electronic properties of N@C60 to those found in atomic nitrogen in the gas phase or trapped in other solid matrices at liquid helium temperature. We conclude that spin-orbit coupling in N@C60 at room temperature is very similar in magnitude and of same sign as found in other inert solid matrices and that interactions between the quartet spin system and the C60 molecular orbitals are thus negligible.

Human factors considerations in the design and evaluation of electronic flight bags (EFBs) : version 2

DOT National Transportation Integrated Search

2003-09-01

Electronic Flight Bags (EFBs) are coming into the flight deck, bringing along with them a wide range of human factors considerations. In order to understand and assess the full impact of an EFB, designers and evaluators require an understanding of ho...

Analyzing the Energy Performance, Wind Loading, and Costs of Photovoltaic Slat Modules on Commercial Rooftops

DOE Office of Scientific and Technical Information (OSTI.GOV)

Van Geet, Otto D.; Fu, Ran; Horowitz, Kelsey A.

NREL studied a new type of photovoltaic (PV) module configuration wherein multiple narrow, tilted slats are mounted in a single frame. Each slat of the PV slat module contains a single row of cells and is made using ordinary crystalline silicon PV module materials and processes, including a glass front sheet and weatherproof polymer encapsulation. Compared to a conventional ballasted system, a system using slat modules offer higher energy production and lower weight at lower LCOE. The key benefits of slat modules are reduced wind loading, improved capacity factor and reduced installation cost. First, the individual slats allow air tomore » flow through, which reduce wind loading. Using PV performance modeling software, we compared the performance of an optimized installation of slats modules to a typical installation of conventional modules in a ballasted rack mounting system. Based on the results of the performance modeling two different row tilt and spacing were tested in a wind tunnel. Scaled models of the PV Slat modules were wind tunnel tested to quantify the wind loading of a slat module system on a commercial rooftop, comparing the results to conventional ballasted rack mounted PV modules. Some commercial roofs do not have sufficient reserve dead load capacity to accommodate a ballasted system. A reduced ballast system design could make PV system installation on these roofs feasible for the first time without accepting the disadvantages of penetrating mounts. Finally, technoeconomic analysis was conducted to enable an economic comparison between a conventional commercial rooftop system and a reduced-ballast slat module installation.« less

Investigation of electron-loss and photon scattering correction factors for FAC-IR-300 ionization chamber

NASA Astrophysics Data System (ADS)

Mohammadi, S. M.; Tavakoli-Anbaran, H.; Zeinali, H. Z.

2017-02-01

The parallel-plate free-air ionization chamber termed FAC-IR-300 was designed at the Atomic Energy Organization of Iran, AEOI. This chamber is used for low and medium X-ray dosimetry on the primary standard level. In order to evaluate the air-kerma, some correction factors such as electron-loss correction factor (ke) and photon scattering correction factor (ksc) are needed. ke factor corrects the charge loss from the collecting volume and ksc factor corrects the scattering of photons into collecting volume. In this work ke and ksc were estimated by Monte Carlo simulation. These correction factors are calculated for mono-energy photon. As a result of the simulation data, the ke and ksc values for FAC-IR-300 ionization chamber are 1.0704 and 0.9982, respectively.

Detour factors in water and plastic phantoms and their use for range and depth scaling in electron-beam dosimetry.

PubMed

Fernández-Varea, J M; Andreo, P; Tabata, T

1996-07-01

Average penetration depths and detour factors of 1-50 MeV electrons in water and plastic materials have been computed by means of analytical calculation, within the continuous-slowing-down approximation and including multiple scattering, and using the Monte Carlo codes ITS and PENELOPE. Results are compared to detour factors from alternative definitions previously proposed in the literature. Different procedures used in low-energy electron-beam dosimetry to convert ranges and depths measured in plastic phantoms into water-equivalent ranges and depths are analysed. A new simple and accurate scaling method, based on Monte Carlo-derived ratios of average electron penetration depths and thus incorporating the effect of multiple scattering, is presented. Data are given for most plastics used in electron-beam dosimetry together with a fit which extends the method to any other low-Z plastic material. A study of scaled depth-dose curves and mean energies as a function of depth for some plastics of common usage shows that the method improves the consistency and results of other scaling procedures in dosimetry with electron beams at therapeutic energies.

Nursing Student Experiences Regarding Safe Use of Electronic Health Records: A Pilot Study of the Safety and Assurance Factors for EHR Resilience Guides.

PubMed

Whitt, Karen J; Eden, Lacey; Merrill, Katreena Collette; Hughes, Mckenna

2017-01-01

Previous research has linked improper electronic health record configuration and use with adverse patient events. In response to this problem, the US Office of the National Coordinator for Health Information Technology developed the Safety and Assurance Factors for EHR Resilience guides to evaluate electronic health records for optimal use and safety features. During the course of their education, nursing students are exposed to a variety of clinical practice settings and electronic health records. This descriptive study evaluated 108 undergraduate and 51 graduate nursing students' ratings of electronic health record features and safe practices, as well as what they learned from utilizing the computerized provider order entry and clinician communication Safety and Assurance Factors for EHR Resilience guide checklists. More than 80% of the undergraduate and 70% of the graduate students reported that they experienced user problems with electronic health records in the past. More than 50% of the students felt that electronic health records contribute to adverse patient outcomes. Students reported that many of the features assessed were not fully implemented in their electronic health record. These findings highlight areas where electronic health records can be improved to optimize patient safety. The majority of students reported that utilizing the Safety and Assurance Factors for EHR Resilience guides increased their understanding of electronic health record features.

Inactivation of marine heterotrophic bacteria in ballast water by an Electrochemical Advanced Oxidation Process.

PubMed

Moreno-Andrés, Javier; Ambauen, Noëmi; Vadstein, Olav; Hallé, Cynthia; Acevedo-Merino, Asunción; Nebot, Enrique; Meyn, Thomas

2018-05-03

Seawater treatment is increasingly required due to industrial activities that use substantial volumes of seawater in their processes. The shipping industry and the associated management of a ship's ballast water are currently considered a global challenge for the seas. Related to that, the suitability of an Electrochemical Advanced Oxidation Process (EAOP) with Boron Doped Diamond (BDD) electrodes has been assessed on a laboratory scale for the disinfection of seawater. This technology can produce both reactive oxygen species and chlorine species (especially in seawater) that are responsible for inactivation. The EAOP was applied in a continuous-flow regime with real seawater. Natural marine heterotrophic bacteria (MHB) were used as an indicator of disinfection efficiency. A biphasic inactivation kinetic model was fitted on experimental points, achieving 4-Log reductions at 0.019 Ah L -1 . By assessing regrowth after treatment, results suggest that higher bacterial damages result from the EAOP when it is compared to chlorination. Furthermore, several issues lacking fundamental understanding were investigated such as recolonization capacity or bacterial community dynamics. It was concluded that, despite disinfection processes being effective, there is not only a possibility for regrowth after treatment but also a change on bacterial population diversity produced by the treatment. Finally, energy consumption was estimated and indicated that 0.264 kWh·m -3 are needed for 4.8-Log reductions of MHB; otherwise, with 0.035 kWh·m -3 , less disinfection efficiency can be obtained (2.2-Log red). However, with a residual oxidant in the solution, total inactivation can be achieved in three days. Copyright © 2018 Elsevier Ltd. All rights reserved.

Relative merits and limiting factors for x-ray and electron microscopy of thick, hydrated organic materials

DOE PAGES

Du, Ming; Jacobsen, Chris

2017-10-07

Electron and x-ray microscopes allow one to image the entire, unlabeled structure of hydrated materials at a resolution well beyond what visible light microscopes can achieve. However, both approaches involve ionizing radiation, so that radiation damage must be considered as one of the limits to imaging. Drawing upon earlier work, we describe here a unified approach to estimating the image contrast (and thus the required exposure and corresponding radiation dose) in both x-ray and electron microscopy. This approach accounts for factors such as plural and inelastic scattering, and (in electron microscopy) the use of energy filters to obtain so-called "zeromore » loss" images. As expected, it shows that electron microscopy offers lower dose for specimens thinner than about 1 mu m (such as for studies of macromolecules, viruses, bacteria and archaebacteria, and thin sectioned material), while x-ray microscopy offers superior characteristics for imaging thicker specimen such as whole eukaryotic cells, thick-sectioned tissues, and organs. The required radiation dose scales strongly as a function of the desired spatial resolution, allowing one to understand the limits of live and frozen hydrated specimen imaging. Lastly, we consider the factors limiting x-ray microscopy of thicker materials, suggesting that specimens as thick as a whole mouse brain can be imaged with x-ray microscopes without significant image degradation should appropriate image reconstruction methods be identified.« less

Relative merits and limiting factors for x-ray and electron microscopy of thick, hydrated organic materials

DOE Office of Scientific and Technical Information (OSTI.GOV)

Du, Ming; Jacobsen, Chris

Electron and x-ray microscopes allow one to image the entire, unlabeled structure of hydrated materials at a resolution well beyond what visible light microscopes can achieve. However, both approaches involve ionizing radiation, so that radiation damage must be considered as one of the limits to imaging. Drawing upon earlier work, we describe here a unified approach to estimating the image contrast (and thus the required exposure and corresponding radiation dose) in both x-ray and electron microscopy. This approach accounts for factors such as plural and inelastic scattering, and (in electron microscopy) the use of energy filters to obtain so-called "zeromore » loss" images. As expected, it shows that electron microscopy offers lower dose for specimens thinner than about 1 mu m (such as for studies of macromolecules, viruses, bacteria and archaebacteria, and thin sectioned material), while x-ray microscopy offers superior characteristics for imaging thicker specimen such as whole eukaryotic cells, thick-sectioned tissues, and organs. The required radiation dose scales strongly as a function of the desired spatial resolution, allowing one to understand the limits of live and frozen hydrated specimen imaging. Lastly, we consider the factors limiting x-ray microscopy of thicker materials, suggesting that specimens as thick as a whole mouse brain can be imaged with x-ray microscopes without significant image degradation should appropriate image reconstruction methods be identified.« less

Quantum confinement and magnetic field effects on the electron Landé g factor in GaAs-(Ga,Al)As double quantum wells

NASA Astrophysics Data System (ADS)

Perea, J. Darío; Mejía-Salazar, J. R.; Porras-Montenegro, N.

2011-12-01

Nowadays the spin-related phenomena have attracted great attention for the possible spintronic and optoelectronic applications. The manipulation of the Landé g factor by means of the control of the electron confinement, applied magnetic field and hydrostatic pressure offers the possibility of having a wide range of ways to control single qubit operation and to have pure spin states to guarantee that no losses occur when the electron spins transport information. In this work we have performed a theoretical study of the quantum confinement (geometrical and barrier potential confinements) and growth direction applied magnetic field effects on the conduction-electron effective Landé g factor in GaAs-(Ga,Al)As double quantum wells. Our calculations of the Landé g factor are performed by using the Ogg-McCombe effective Hamiltonian, which includes non-parabolicity and anisotropy effects for the conduction-band electrons. Our theoretical results are given as function of the central barrier widths for different values of the applied magnetic fields. We have found that in this type of heterostructure the geometrical confinement commands the behavior of the electron effective Landé g factor as compared to the effect of the applied magnetic field. Present theoretical reports are in very good agreement with previous experimental and theoretical results.

Market factors and electronic medical record adoption in medical practices.

PubMed

Menachemi, Nir; Mazurenko, Olena; Kazley, Abby Swanson; Diana, Mark L; Ford, Eric W

2012-01-01

Previous studies identified individual or practice factors that influence practice-based physicians' electronic medical record (EMR) adoption. Less is known about the market factors that influence physicians' EMR adoption. The aim of this study was to explore the relationship between environmental market characteristics and physicians' EMR adoption. The Health Tracking Physician Survey 2008 and Area Resource File (2008) were combined and analyzed. Binary logistic regression was used to examine the relationship between three dimensions of the market environment (munificence, dynamism, and complexity) and EMR adoption controlling for several physician and practice characteristics. In a nationally representative sample of 4,720 physicians, measures of market dynamism including increases in unemployment, odds ratio (OR) = 0.95, 95% confidence interval (CI) [0.91, 0.99], or poverty rates, OR = 0.93, 95% CI [0.89, 0.96], were negatively associated with EMR adoption. Health maintenance organization penetration, OR = 3.01, 95% CI [1.49, 6.05], another measure of dynamism, was positively associated with EMR adoption. Physicians practicing in areas with a malpractice crisis, OR = 0.82, 95% CI [0.71, 0.94], representing environmental complexity, had lower EMR adoption rates. Understanding how market factors relate to practice-based physicians' EMR adoption can assist policymakers to better target limited resources as they work to realize the national goal of universal EMR adoption and meaningful use.

Which Factors Influence the Willingness to Pay for Electronic Library Services? A Study of the Portuguese Electronic Scientific Information Consortium B-On1

ERIC Educational Resources Information Center

Melo, Luiza Baptista; Pires, Cesaltina

2012-01-01

This paper investigates the factors that influence the value for the users of the Portuguese electronic scientific information consortium b-on (Biblioteca do Conhecimento Online). We used the contingent valuation method based on a willingness to pay scenario to estimate the value that each user is willing to pay. Data were collected through an…

Relative merits and limiting factors for x-ray and electron microscopy of thick, hydrated organic materials.

PubMed

Du, Ming; Jacobsen, Chris

2018-01-01

Electron and x-ray microscopes allow one to image the entire, unlabeled structure of hydrated materials at a resolution well beyond what visible light microscopes can achieve. However, both approaches involve ionizing radiation, so that radiation damage must be considered as one of the limits to imaging. Drawing upon earlier work, we describe here a unified approach to estimating the image contrast (and thus the required exposure and corresponding radiation dose) in both x-ray and electron microscopy. This approach accounts for factors such as plural and inelastic scattering, and (in electron microscopy) the use of energy filters to obtain so-called "zero loss" images. As expected, it shows that electron microscopy offers lower dose for specimens thinner than about 1 µm (such as for studies of macromolecules, viruses, bacteria and archaebacteria, and thin sectioned material), while x-ray microscopy offers superior characteristics for imaging thicker specimen such as whole eukaryotic cells, thick-sectioned tissues, and organs. The required radiation dose scales strongly as a function of the desired spatial resolution, allowing one to understand the limits of live and frozen hydrated specimen imaging. Finally, we consider the factors limiting x-ray microscopy of thicker materials, suggesting that specimens as thick as a whole mouse brain can be imaged with x-ray microscopes without significant image degradation should appropriate image reconstruction methods be identified. Copyright © 2017 Elsevier B.V. All rights reserved.

Psychosocial Factors Associated With Adolescent Electronic Cigarette and Cigarette Use

PubMed Central

Berhane, Kiros; Unger, Jennifer B.; Cruz, Tess Boley; Huh, Jimi; Leventhal, Adam M.; Urman, Robert; Wang, Kejia; Howland, Steve; Gilreath, Tamika D.; Chou, Chih-Ping; Pentz, Mary Ann; McConnell, Rob

2015-01-01

BACKGROUND: Use of electronic cigarettes (e-cigarettes) among adolescents has increased since their introduction into the US market in 2007. Little is known about the role of e-cigarette psychosocial factors on risk of e-cigarette or cigarette use in adolescence. METHODS: Information on e-cigarette and cigarette psychosocial factors (use and attitudes about use in the home and among friends) was collected from 11th- and 12th-grade participants in the Southern California Children’s Health Study during the spring of 2014. RESULTS: Of 2084 participants, 499 (24.0%) had used an e-cigarette, including 200 (9.6%) current users (past 30 days); 390 participants (18.7%) had smoked a combustible cigarette, and 119 (5.7%) were current cigarette smokers. Cigarette and e-cigarette use were correlated. Nevertheless, 40.5% (n = 81) of current e-cigarette users had never smoked a cigarette. Psychosocial factors (home use of each product, friends’ use of and positive attitudes toward e-cigarettes and cigarettes) and participant perception of the harm of e-cigarettes were strongly positively associated both with e-cigarette and cigarette use. Most youth who reported e-cigarette use had friends who used e-cigarettes, and almost half of current users reported that they did not believe there were health risks associated with e-cigarette use. CONCLUSIONS: Longitudinal studies of adolescents are needed to determine whether the strong association of e-cigarette psychosocial factors with both e-cigarette and cigarette use will lead to increased cigarette use or dual use of cigarettes and e-cigarettes, or whether e-cigarettes will serve as a gateway to cigarette use. PMID:26216326

Chamber study of PCBemissions from caulking materials and ...

EPA Pesticide Factsheets

The emissions of polychlorinated biphenyl (PCB) congeners from 13 caulk samples were tested in a micro-chamber system. Twelve samples were from PCB-contaminated buildings and one was prepared in the laboratory. Nineteen light ballasts collected from buildings that represent 13 different models from five manufacturers were tested in 53-liter environmental chambers. The rates of PCB congener emissions from caulking materials and light ballasts were determined. Several factors that may have affected the emission rates were evaluated. The experimentally determined emission factors showed that, for a given PCB congener, there is a linear correlation between the emission factor and the concentration of the PCB congener in the source. Furthermore, the test results showed that an excellent log-linear correlation exists between the normalized emission factor and the vapor pressure (coefficient of determination, r2 ≥0.8846). The PCB congener emissions from ballasts at or near room temperature were relatively low with or without electrical load. However, the PCB congener emission rates increased significantly as the temperature increased. The results of this research provide new data and models for ranking the primary sources of PCBs and supports the development and refinement of exposure assessment models for PCBs. This study supplemented and complemented the field measurements in buildings conducted by U.S. EPA National Exposure Research Laboratory by providing a bette

High Thermoelectric Power Factor of High‐Mobility 2D Electron Gas

PubMed Central

Kim, Sung Wng; Kaneki, Shota; Yamamoto, Atsushi

2017-01-01

Abstract Thermoelectric conversion is an energy harvesting technology that directly converts waste heat from various sources into electricity by the Seebeck effect of thermoelectric materials with a large thermopower (S), high electrical conductivity (σ), and low thermal conductivity (κ). State‐of‐the‐art nanostructuring techniques that significantly reduce κ have realized high‐performance thermoelectric materials with a figure of merit (ZT = S 2∙σ∙T∙κ−1) between 1.5 and 2. Although the power factor (PF = S 2∙σ) must also be enhanced to further improve ZT, the maximum PF remains near 1.5–4 mW m−1 K−2 due to the well‐known trade‐off relationship between S and σ. At a maximized PF, σ is much lower than the ideal value since impurity doping suppresses the carrier mobility. A metal‐oxide‐semiconductor high electron mobility transistor (MOS‐HEMT) structure on an AlGaN/GaN heterostructure is prepared. Applying a gate electric field to the MOS‐HEMT simultaneously modulates S and σ of the high‐mobility electron gas from −490 µV K−1 and ≈10−1 S cm−1 to −90 µV K−1 and ≈104 S cm−1, while maintaining a high carrier mobility (≈1500 cm2 V−1 s−1). The maximized PF of the high‐mobility electron gas is ≈9 mW m−1 K−2, which is a two‐ to sixfold increase compared to state‐of‐the‐art practical thermoelectric materials. PMID:29375980

High Thermoelectric Power Factor of High-Mobility 2D Electron Gas.

PubMed

Ohta, Hiromichi; Kim, Sung Wng; Kaneki, Shota; Yamamoto, Atsushi; Hashizume, Tamotsu

2018-01-01

Thermoelectric conversion is an energy harvesting technology that directly converts waste heat from various sources into electricity by the Seebeck effect of thermoelectric materials with a large thermopower ( S ), high electrical conductivity (σ), and low thermal conductivity (κ). State-of-the-art nanostructuring techniques that significantly reduce κ have realized high-performance thermoelectric materials with a figure of merit ( ZT = S 2 ∙σ∙ T ∙κ -1 ) between 1.5 and 2. Although the power factor (PF = S 2 ∙σ) must also be enhanced to further improve ZT , the maximum PF remains near 1.5-4 mW m -1 K -2 due to the well-known trade-off relationship between S and σ. At a maximized PF, σ is much lower than the ideal value since impurity doping suppresses the carrier mobility. A metal-oxide-semiconductor high electron mobility transistor (MOS-HEMT) structure on an AlGaN/GaN heterostructure is prepared. Applying a gate electric field to the MOS-HEMT simultaneously modulates S and σ of the high-mobility electron gas from -490 µV K -1 and ≈10 -1 S cm -1 to -90 µV K -1 and ≈10 4 S cm -1 , while maintaining a high carrier mobility (≈1500 cm 2 V -1 s -1 ). The maximized PF of the high-mobility electron gas is ≈9 mW m -1 K -2 , which is a two- to sixfold increase compared to state-of-the-art practical thermoelectric materials.

Fabrication of high-power piezoelectric transformers using lead-free ceramics for application in electronic ballasts.

PubMed

Yang, Song-Ling; Chen, Shih-Ming; Tsai, Cheng-Che; Hong, Cheng-Shong; Chu, Sheng-Yuan

2013-02-01

CuO is doped into (Na(0.5)K(0.5))NbO(3) (NKN) ceramics to improve the piezoelectric properties and thus obtain a piezoelectric transformer (PT) with high output power. In X-ray diffraction patterns, the diffraction angles of the CuO-doped NKN ceramics shift to lower values because of an expansion of the lattice volume, thus inducing oxygen vacancies and enhancing the mechanical quality factor. A homogeneous microstructure is obtained when NKN is subjected to CuO doping, leading to improved electrical properties. PTs with different electrode areas are fabricated using the CuO-doped NKN ceramics. Considering the efficiency, voltage gain, and temperature rise of PTs at a load resistance of 1 kΩ, PTs with an electrode with an inner diameter of 15 mm are combined with the circuit design for driving a 13-W T5 fluorescent lamp. A temperature rise of 6°C and a total efficiency of 82.4% (PT and circuit) are obtained using the present PTs.

Examination of enterotoxigenic Escherichia coli H10407 (colonization factor antigen I+) by scanning electron microscopy with conductive staining.

PubMed Central

Sherburne, R; Armstrong, G D

1989-01-01

We have used the scanning electron microscope to examine enterotoxigenic Escherichia coli H10407, which expresses colonization factor antigen I pili. The use of low accelerating voltages and conductive staining procedures allowed us to obtain images of colonization factor antigen I pili and other structural details which were obscured by conventional gold-coating techniques. Images PMID:2570062

75 FR 37975 - Energy Conservation Program for Consumer Products and Certain Commercial and Industrial Equipment...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-07-01

... technologies including induction and fluorescent lamps. 75 FR 22031, 22033 (April 27, 2010). In comments... of magnetic ballasts of 50,000 hours. After the 2003 draft report, Allegheny noted that MV ballast... considered only magnetic ballasts because they are the most common ballast used in HID lighting systems. DOE...

Electronic Portfolios in the Classroom: Factors Impacting Teachers' Integration of New Technologies and New Pedagogies

ERIC Educational Resources Information Center

Meyer, E. J.; Abrami, P. C.; Wade, A.; Scherzer, R.

2011-01-01

This article presents the findings of a study on the use of an electronic portfolio (EP) in 16 elementary classrooms across Canada. Using a mixed-methods approach, data were collected to understand how teachers used EPs in their classrooms, to what extent they integrated the EP into their practice, and the factors influencing their use. Using…

Adapting Wireless Technology to Lighting Control and Environmental Sensing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dana Teasdale; Francis Rubinstein; David S. Watson

Although advanced lighting control systems offer significant energy savings, the high cost of retrofitting buildings with advanced lighting control systems is a barrier to adoption of this energy-saving technology. Wireless technology, however, offers a solution to mounting installation costs since it requires no additional wiring to implement. To demonstrate the feasibility of such a system, a prototype wirelessly-controlled advanced lighting system was designed and built. The system includes the following components: a wirelessly-controllable analog circuit module (ACM), a wirelessly-controllable electronic dimmable ballast, a T8 3-lamp fixture, an environmental multi-sensor, a current transducer, and control software. The ACM, dimmable ballast, multi-sensor,more » and current transducer were all integrated with SmartMesh{trademark} wireless mesh networking nodes, called motes, enabling wireless communication, sensor monitoring, and actuator control. Each mote-enabled device has a reliable communication path to the SmartMesh Manager, a single board computer that controls network functions and connects the wireless network to a PC running lighting control software. The ACM is capable of locally driving one or more standard 0-10 Volt electronic dimmable ballasts through relay control and a 0-10 Volt controllable output, in addition to 0-24 Volt and 0-10 Volt inputs. The mote-integrated electronic dimmable ballast is designed to drive a standard 3-lamp T8 light fixture. The environmental multisensor measures occupancy, light level and temperature. The current transducer is used to measure the power consumed by the fixture. Control software was developed to implement advanced lighting algorithms, including open and closed-loop daylight ramping, occupancy control, and demand response. Engineering prototypes of each component were fabricated and tested in a bench-scale system. Based on standard industry practices, a cost analysis was conducted. It is estimated that

Factors contributing to perceptions about policies regarding the electronic monitoring of sex offenders: the role of demographic characteristics, victimization experiences, and social disorganization.

PubMed

Button, Deeanna M; Tewksbury, Richard; Mustaine, Elizabeth E; Payne, Brian K

2013-01-01

The purpose of this article is to explore factors contributing to perceptions about electronic monitoring policies governing sex offenders. Guided by Tannenbaum's theory of attribution and Shaw and McKay's theory of social disorganization, the authors examine the influence of demographic characteristics, victimization experiences, and neighborhood characteristics on perceptions about policies regarding the electronic monitoring of sex offenders. Ordinary least squares regression and logistic regression analyses of stratified telephone survey data reveal that factors associated with favorable views on the use of global positioning satellite monitoring for registered sex offenders appear to stem primarily from individuals' demographic characteristics. Experiential and neighborhood factors do provide some influence over individuals' views of electronic monitoring policies for sex offenders. Theoretical and policy implications are discussed.

Acoustic Studies of Ocean Surface Processes in SWAPP

DTIC Science & Technology

1992-02-05

detected with an accelerometer and tiltmeters , and corrections are made in the data analysis where appropriate. Additional sensors , which are not discussed...electronics case battery case compass depth sensor submersible floats ballast weight acoustic release Figure 1. dW CN CC) Q!) CN (w UL C e Figure 2. -r

Factors affecting electronic health record adoption in long-term care facilities.

PubMed

Cherry, Barbara; Carter, Michael; Owen, Donna; Lockhart, Carol

2008-01-01

Electronic health records (EHRs) hold the potential to significantly improve the quality of care in long-term care (LTC) facilities, yet limited research has been done on how facilities decide to adopt these records. This study was conducted to identify factors that hinder and facilitate EHR adoption in LTC facilities. Study participants were LTC nurses, administrators, and corporate executives. Primary barriers identified were costs, the need for training, and the culture change required to embrace technology. Primary facilitators were training programs, well-defined implementation plans, government assistance with implementation costs, evidence that EHRs will improve care outcomes, and support from state regulatory agencies. These results offer a framework of action for policy makers, LTC Leaders, and researchers.

The gj factor of a bound electron and the hyperfine structure splitting in hydrogenlike ions

NASA Astrophysics Data System (ADS)

Beier, Thomas

2000-12-01

The comparison between theory and experiment of the hyperfine structure splitting and the electronic gj factor in heavy highly charged ions provides a unique testing ground for quantum electrodynamics in the presence of strong electric and magnetic fields. A theoretical evaluation is presented of all quantum electrodynamical contributions to the ground-state hfs splitting in hydrogenlike and lithiumlike atoms as well as to the gj factor. Binding and nuclear effects are discussed as well. A comparison with the available experimental data is performed, and a detailed discussion of theoretical sources of uncertainty is included which is mainly due to insufficiently known nuclear properties.

Human factors considerations in the design and evaluation of electronic flight bags (EFBs), version 1 : basic functions

DOT National Transportation Integrated Search

2003-09-01

Electronic Flight Bags (EFBs) are coming into the flight deck, bringing along with them a wide range of human factors considerations. In order to understand and assess the full impact of an EFB, designers and evaluators require an understanding of ho...

SU-E-T-554: Comparison of Electron Disequilibrium Factor in External Photon Beams for Different Models of Linear Accelerators

DOE Office of Scientific and Technical Information (OSTI.GOV)

LIU, B; Zhu, T

Purpose: The dose in the buildup region of a photon beam is usually determined by the transport of the primary secondary electrons and the contaminating electrons from accelerator head. This can be quantified by the electron disequilibrium factor, E, defined as the ratio between total dose and equilibrium dose (proportional to total kerma), E = 1 in regions beyond buildup region. Ecan be different among accelerators of different models and/or manufactures of the same machine. This study compares E in photon beams from different machine models/ Methods: Photon beam data such as fractional depth dose curve (FDD) and phantom scattermore » factors as a function of field size and phantom depth were measured for different Linac machines. E was extrapolated from these fractional depth dose data while taking into account inverse-square law. The ranges of secondary electron were chosen as 3 and 6 cm for 6 and 15 MV photon beams, respectively. The field sizes range from 2x2 to 40x40 cm{sup 2}. Results: The comparison indicates the standard deviations of electron contamination among different machines are about 2.4 - 3.3% at 5 mm depth for 6 MV and 1.2 - 3.9% at 1 cm depth for 15 MV for the same field size. The corresponding maximum deviations are 3.0 - 4.6% and 2 - 4% for 6 and 15 MV, respectively. Both standard and maximum deviations are independent of field sizes in the buildup region for 6 MV photons, and slightly decreasing with increasing field size at depths up to 1 cm for 15 MV photons. Conclusion: The deviations of electron disequilibrium factor for all studied Linacs are less than 3% beyond the depth of 0.5 cm for the photon beams for the full range of field sizes (2-40 cm) so long as they are from the same manufacturer.« less

Impact analyses for negative flexural responses (hogging) in railway prestressed concrete sleepers

NASA Astrophysics Data System (ADS)

Kaewunruen, S.; Ishida, T.; Remennikov, AM

2016-09-01

By nature, ballast interacts with railway concrete sleepers in order to provide bearing support to track system. Most train-track dynamic models do not consider the degradation of ballast over time. In fact, the ballast degradation causes differential settlement and impact forces acting on partial and unsupported tracks. Furthermore, localised ballast breakages underneath railseat increase the likelihood of centrebound cracks in concrete sleepers due to the unbalanced support under sleepers. This paper presents a dynamic finite element model of a standard-gauge concrete sleeper in a track system, taking into account the tensionless nature of ballast support. The finite element model was calibrated using static and dynamic responses in the past. In this paper, the effects of centre-bound ballast support on the impact behaviours of sleepers are highlighted. In addition, it is the first to demonstrate the dynamic effects of sleeper length on the dynamic design deficiency in concrete sleepers. The outcome of this study will benefit the rail maintenance criteria of track resurfacing in order to restore ballast profile and appropriate sleeper/ballast interaction.

Evaluation of Energy Efficiency Improvements to Portable Classrooms in Florida.

ERIC Educational Resources Information Center

Callahan, Michael P.; Parker, Danny S.; Sherwin, John R.; Anello, Michael T.

Findings are presented from a 2-year experiment exploring ways to reduce energy costs and improve the learning environment in Florida's 25,000 portable classrooms. Improvements were made in two highly instrumented portable classrooms in the following areas: installation of a T8 lighting system with electronic ballasts; a high efficiency heat pump…

Electron holes in inhomogeneous magnetic field: Electron heating and electron hole evolution

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vasko, I. Y.; Space Research Institute of Russian Academy of Science, Moscow; Agapitov, O. V.

Electron holes are electrostatic non-linear structures widely observed in the space plasma. In the present paper, we analyze the process of energy exchange between electrons trapped within electron hole, untrapped electrons, and an electron hole propagating in a weakly inhomogeneous magnetic field. We show that as the electron hole propagates into the region with stronger magnetic field, trapped electrons are heated due to the conservation of the first adiabatic invariant. At the same time, the electron hole amplitude may increase or decrease in dependence on properties of distribution functions of trapped and untrapped resonant electrons. The energy gain of trappedmore » electrons is due to the energy losses of untrapped electrons and/or decrease of the electron hole energy. We stress that taking into account the energy exchange with untrapped electrons increases the lifetime of electron holes in inhomogeneous magnetic field. We illustrate the suggested mechanism for small-amplitude Schamel's [Phys. Scr. T2, 228–237 (1982)] electron holes and show that during propagation along a positive magnetic field gradient their amplitude should grow. Neglect of the energy exchange with untrapped electrons would result in the electron hole dissipation with only modest heating factor of trapped electrons. The suggested mechanism may contribute to generation of suprathermal electron fluxes in the space plasma.« less

Direct determination of k Q factors for cylindrical and plane-parallel ionization chambers in high-energy electron beams from 6 MeV to 20 MeV.

PubMed

Krauss, A; Kapsch, R-P

2018-02-06

For the ionometric determination of the absorbed dose to water, D w , in high-energy electron beams from a clinical accelerator, beam quality dependent correction factors, k Q , are required. By using a water calorimeter, these factors can be determined experimentally and potentially with lower standard uncertainties than those of the calculated k Q factors, which are tabulated in various dosimetry protocols. However, one of the challenges of water calorimetry in electron beams is the small measurement depths in water, together with the steep dose gradients present especially at lower energies. In this investigation, water calorimetry was implemented in electron beams to determine k Q factors for different types of cylindrical and plane-parallel ionization chambers (NE2561, NE2571, FC65-G, TM34001) in 10 cm  ×  10 cm electron beams from 6 MeV to 20 MeV (corresponding beam quality index R 50 ranging from 1.9 cm to 7.5 cm). The measurements were carried out using the linear accelerator facility of the Physikalisch-Technische Bundesanstalt. Relative standard uncertainties for the k Q factors between 0.50% for the 20 MeV beam and 0.75% for the 6 MeV beam were achieved. For electron energies above 8 MeV, general agreement was found between the relative electron energy dependencies of the k Q factors measured and those derived from the AAPM TG-51 protocol and recent Monte Carlo-based studies, as well as those from other experimental investigations. However, towards lower energies, discrepancies of up to 2.0% occurred for the k Q factors of the TM34001 and the NE2571 chamber.

Direct determination of k Q factors for cylindrical and plane-parallel ionization chambers in high-energy electron beams from 6 MeV to 20 MeV

NASA Astrophysics Data System (ADS)

Krauss, A.; Kapsch, R.-P.

2018-02-01

For the ionometric determination of the absorbed dose to water, D w, in high-energy electron beams from a clinical accelerator, beam quality dependent correction factors, k Q, are required. By using a water calorimeter, these factors can be determined experimentally and potentially with lower standard uncertainties than those of the calculated k Q factors, which are tabulated in various dosimetry protocols. However, one of the challenges of water calorimetry in electron beams is the small measurement depths in water, together with the steep dose gradients present especially at lower energies. In this investigation, water calorimetry was implemented in electron beams to determine k Q factors for different types of cylindrical and plane-parallel ionization chambers (NE2561, NE2571, FC65-G, TM34001) in 10 cm  ×  10 cm electron beams from 6 MeV to 20 MeV (corresponding beam quality index R 50 ranging from 1.9 cm to 7.5 cm). The measurements were carried out using the linear accelerator facility of the Physikalisch-Technische Bundesanstalt. Relative standard uncertainties for the k Q factors between 0.50% for the 20 MeV beam and 0.75% for the 6 MeV beam were achieved. For electron energies above 8 MeV, general agreement was found between the relative electron energy dependencies of the k Q factors measured and those derived from the AAPM TG-51 protocol and recent Monte Carlo-based studies, as well as those from other experimental investigations. However, towards lower energies, discrepancies of up to 2.0% occurred for the k Q factors of the TM34001 and the NE2571 chamber.

Strong confinement-induced engineering of the g factor and lifetime of conduction electron spins in Ge quantum wells

PubMed Central

Giorgioni, Anna; Paleari, Stefano; Cecchi, Stefano; Vitiello, Elisa; Grilli, Emanuele; Isella, Giovanni; Jantsch, Wolfgang; Fanciulli, Marco; Pezzoli, Fabio

2016-01-01

Control of electron spin coherence via external fields is fundamental in spintronics. Its implementation demands a host material that accommodates the desirable but contrasting requirements of spin robustness against relaxation mechanisms and sizeable coupling between spin and orbital motion of the carriers. Here, we focus on Ge, which is a prominent candidate for shuttling spin quantum bits into the mainstream Si electronics. So far, however, the intrinsic spin-dependent phenomena of free electrons in conventional Ge/Si heterojunctions have proved to be elusive because of epitaxy constraints and an unfavourable band alignment. We overcome these fundamental limitations by investigating a two-dimensional electron gas in quantum wells of pure Ge grown on Si. These epitaxial systems demonstrate exceptionally long spin lifetimes. In particular, by fine-tuning quantum confinement we demonstrate that the electron Landé g factor can be engineered in our CMOS-compatible architecture over a range previously inaccessible for Si spintronics. PMID:28000670

Treatment of heavy metal polluted industrial wastewater by a new water treatment process: ballasted electroflocculation.

PubMed

Brahmi, Khaled; Bouguerra, Wided; Harbi, Soumaya; Elaloui, Elimame; Loungou, Mouna; Hamrouni, Béchir

2018-02-15

This laboratory study investigated the parameters efficiency of the new technology: ballasted electro-flocculation (BEF) using aluminum (Al) electrodes to remove cadmium and zinc from industrial mining wastewater (MWW). The principle of the BEF process is based on the use of micro-sand and polymer together to increase the weight of the flocs and the rate at which they settle is radically changing the electrocoagulation-electroflocculation settling methodology. Based on the examination of the operation parameters one by one, the best removal percentage was obtained at a current intensity of 2A, a the flow rate of 20L/h, a micro-sand dose of 6g/L, a polyéthylèneimine (PEI) polymer dose of 100mg, the contact times of 30min, a stirring speed of 50 RPM, a monopolar configuration of the electrodes, and an electrodes number of 10. The results showed that the flow rate and the current density have a preponderant effect on the variability of the quality of the settled water. In comparison, filterability was found to be more sensitive to number of electrodes, micro sand dosages and current density. It was dependent on the ratio of microsand to PEI polymer dosage, and improved when this ratio increased. Response surface methodology was applied to evaluate the main effects and interactions among stirring speed, polymer dose, current intensity, and electrodes number. The removal of Cd and Zn from industrial MWW was done for very low cost of 0.1TND/m 3 equivalent to 0.04€/m 3 . The investigation of BEF process proposes a highly cost-effective wastewater treatment method if compared to Actiflo TM and electrocoagulation. Copyright © 2017 Elsevier B.V. All rights reserved.

SU-E-T-98: An Analysis of TG-51 Electron Beam Calibration Correction Factor Uncertainty

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lee, P; Alvarez, P; Taylor, P

Purpose: To analyze the uncertainty of the TG-51 electron beam calibration correction factors for farmer type ion chambers currently used by institutions visited by IROC Houston. Methods: TG-51 calibration data were collected from 181 institutions visited by IROC Houston physicists for 1174 and 197 distinct electron beams from modern Varian and Elekta accelerators, respectively. Data collected and analyzed included ion chamber make and model, nominal energy, N{sub D,w}, I{sub 50}, R{sub 50}, k’R{sub 50}, d{sub ref}, P{sub gr} and pdd(d{sub ref}). k’R{sub 50} data for parallel plate chambers were excluded from the analysis. Results: Unlike photon beams, electron nominal energymore » is a poor indicator of the actual energy as evidenced by the range of R{sub 50} values for each electron beam energy (6–22MeV). The large range in R{sub 50} values resulted k’R{sub 50} values with a small standard deviation but large range between maximum value used and minimum value (0.001–0.029) used for a specific Varian nominal energy. Varian data showed more variability in k’R{sub 50} values than the Elekta data (0.001–0.014). Using the observed range of R{sub 50} values, the maximum spread in k’R{sub 50} values was determined by IROC Houston and compared to the spread of k’R{sub 50} values used in the community. For Elekta linacs the spreads were equivalent, but for Varian energies of 6 to 16MeV, the community spread was 2 to 6 times larger. Community P{sub gr} values had a much larger range of values for 6 and 9 MeV values than predicted. The range in Varian pdd(d{sub ref} ) used by the community for low energies was large, (1.4–4.9 percent), when it should have been very close to unity. Exradin, PTW Roos and PTW farmer chambers N{sub D,w} values showed the largest spread, ≥11 percent. Conclusion: While the vast majority of electron beam calibration correction factors used are accurate, there is a surprising spread in some of the values used.« less

Pair potentials for liquid sodium near freezing from electron theory and from inversion of the measured structure factor

NASA Astrophysics Data System (ADS)

Perrot, F.; March, N. H.

An effective pair potential for liquid sodium near freezing has been calculated from electron theory using the density-functional method. The main features of the potential extracted by Reatto, Levesque, and Weis [phys. Rev. A 33, 3451 (1986)] by inverting the measured structure factor of Greenfield, Wellendorf, and Wiser [Phys. Rev. A 4, 1607 (1971)] are faithfully reflected by electron theory. To obtain precise agreement between the two methods will evidently require further progress in setting up nonlocal exchange and correlation functionals.

Combining Knowledge and Data Driven Insights for Identifying Risk Factors using Electronic Health Records

PubMed Central

Sun, Jimeng; Hu, Jianying; Luo, Dijun; Markatou, Marianthi; Wang, Fei; Edabollahi, Shahram; Steinhubl, Steven E.; Daar, Zahra; Stewart, Walter F.

2012-01-01

Background: The ability to identify the risk factors related to an adverse condition, e.g., heart failures (HF) diagnosis, is very important for improving care quality and reducing cost. Existing approaches for risk factor identification are either knowledge driven (from guidelines or literatures) or data driven (from observational data). No existing method provides a model to effectively combine expert knowledge with data driven insight for risk factor identification. Methods: We present a systematic approach to enhance known knowledge-based risk factors with additional potential risk factors derived from data. The core of our approach is a sparse regression model with regularization terms that correspond to both knowledge and data driven risk factors. Results: The approach is validated using a large dataset containing 4,644 heart failure cases and 45,981 controls. The outpatient electronic health records (EHRs) for these patients include diagnosis, medication, lab results from 2003–2010. We demonstrate that the proposed method can identify complementary risk factors that are not in the existing known factors and can better predict the onset of HF. We quantitatively compare different sets of risk factors in the context of predicting onset of HF using the performance metric, the Area Under the ROC Curve (AUC). The combined risk factors between knowledge and data significantly outperform knowledge-based risk factors alone. Furthermore, those additional risk factors are confirmed to be clinically meaningful by a cardiologist. Conclusion: We present a systematic framework for combining knowledge and data driven insights for risk factor identification. We demonstrate the power of this framework in the context of predicting onset of HF, where our approach can successfully identify intuitive and predictive risk factors beyond a set of known HF risk factors. PMID:23304365

Electronic media use by children in families of high socioeconomic level and familial factors.

PubMed

Kayiran, Sinan Mahir; Soyak, Güzide; Gürakan, Berkan

2010-01-01

The aim of this research was to describe electronic media access and use among children aged 6 months to 15 years and to identify familial factors. Data was collected with a questionnaire from 724 parents of children seen in the pediatric outpatient clinic of a private hospital while they awaited examination. Questions included electronic media ownership at home or in the child's bedroom, household habits of electronic media use, educational and occupational status of parents, smoking and alcohol consumption at home, and family income. The top three electronic media devices present at home were television, computer and DVD. On a typical day, 32% of children watched television for approximately less than 1 hour, 36% for 2 hours and 22% for 3 hours. Mean television viewing time was 1.89 +/- 0.76 hours. Nearly 12% of parents spent less than 30 minutes with their children, whereas 28% spent 1 hour, and 59% more than 1 hour. Older children spent more time watching television than the younger ones. Forty-six percent of children used computer and the internet at home on a typical day. Almost 20% of children also had a television in their bedroom and spent more time watching television than those without a television in their bedroom, and the ratio increased by age (one-fifth of 3-5-year olds, one-fourth of 6-10-year-olds and half of 11-15-year-olds, on average). The present study provides data for the education and counselling of parents about the use of electronic media by children and it will contribute to increasing the awareness and sensitivity of the population by drawing attention to the subject.

Preventing maritime transport of pathogens: the remarkable antimicrobial properties of silver-supported catalysts for ship ballast water disinfection.

PubMed

Theologides, C P; Theofilou, S P; Anayiotos, A; Costa, C N

2017-07-01

Ship ballast water (SBW) antimicrobial treatment is considered as a priority issue for the shipping industry. The present work investigates the possibility of utilizing antimicrobial catalysis as an effective method for the treatment of SBW. Taking into account the well-known antimicrobial properties of ionic silver (Ag + ), five silver-supported catalysts (Ag/γ-Al 2 O 3 ) with various loadings (0.05, 0.1, 0.2, 0.5, and 1 wt%) were prepared and examined for the antimicrobial treatment of SBW. The bactericidal activity of the aforementioned catalysts was investigated towards the inhibition of Escherichia coli (Gram-negative) and Escherichia faecalis (Gram-positive) bacteria. Catalytic experiments were conducted in a three-phase continuous flow stirred tank reactor, used in a semi-batch mode. It was found that using the catalyst with the lowest metal loading, the inhibition of E. coli reached 95.8% after 30 minutes of treatment of an E. coli bacterial solution, while the inhibition obtained for E. faecalis was 76.2% after 60 minutes of treatment of an E. faecalis bacterial solution. Even better results (100% inhibition after 5 min of reaction) were obtained using the catalysts with higher Ag loadings. The results of the present work indicate that the prepared monometallic catalysts exert their antimicrobial activity within a short period of time, revealing, for the first time ever, that the field of antimicrobial heterogeneous catalysis using deposited ionic silver on a solid support may prove decisive for the disinfection of SBW.

Exploring critical factors influencing physicians' acceptance of mobile electronic medical records based on the dual-factor model: a validation in Taiwan.

PubMed

Liu, Chung-Feng; Cheng, Tain-Junn

2015-02-07

With respect to information management, most of the previous studies on the acceptance of healthcare information technologies were analyzed from "positive" perspectives. However, such acceptance is always influenced by both positive and negative factors and it is necessary to validate both in order to get a complete understanding. This study aims to explore physicians' acceptance of mobile electronic medical records based on the dual-factor model, which is comprised of inhibitors and enablers, to explain an individual's technology usage. Following an earlier healthcare study in the USA, the researchers conducted a similar survey for an Eastern country (Taiwan) to validate whether perceived threat to professional autonomy acts as a critical inhibitor. In addition, perceived mobility, which is regarded as a critical feature of mobile services, was also evaluated as a common antecedent variable in the model. Physicians from three branch hospitals of a medical group were invited to participate and complete questionnaires. Partial least squares, a structural equation modeling technique, was used to evaluate the proposed model for explanatory power and hypotheses testing. 158 valid questionnaires were collected, yielding a response rate of 33.40%. As expected, the inhibitor of perceived threat has a significant impact on the physicians' perceptions of usefulness as well as their intention to use. The enablers of perceived ease of use and perceived usefulness were also significant. In addition, as expected, perceived mobility was confirmed to have a significant impact on perceived ease of use, perceived usefulness and perceived threat. It was confirmed that the dual-factor model is a comprehensive method for exploring the acceptance of healthcare information technologies, both in Western and Eastern countries. Furthermore, perceived mobility was proven to be an effective antecedent variable in the model. The researchers believe that the results of this study will

Monte Carlo simulation for Neptun 10 PC medical linear accelerator and calculations of output factor for electron beam

PubMed Central

Bahreyni Toossi, Mohammad Taghi; Momennezhad, Mehdi; Hashemi, Seyed Mohammad

2012-01-01

Aim Exact knowledge of dosimetric parameters is an essential pre-requisite of an effective treatment in radiotherapy. In order to fulfill this consideration, different techniques have been used, one of which is Monte Carlo simulation. Materials and methods This study used the MCNP-4Cb to simulate electron beams from Neptun 10 PC medical linear accelerator. Output factors for 6, 8 and 10 MeV electrons applied to eleven different conventional fields were both measured and calculated. Results The measurements were carried out by a Wellhofler-Scanditronix dose scanning system. Our findings revealed that output factors acquired by MCNP-4C simulation and the corresponding values obtained by direct measurements are in a very good agreement. Conclusion In general, very good consistency of simulated and measured results is a good proof that the goal of this work has been accomplished. PMID:24377010

Transmission effects in unfolding electronic-vibrational electron-molecule energy-loss spectra

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang Shiyang; Khakoo, Murtadha A.; Johnson, Paul V.

2006-03-15

The results of an investigation concerning the sensitivity of conventional unfolding methods applied to electronic-vibrational electron-energy-loss spectra to the transmission efficiency of electron spectrometers are presented. This investigation was made in an effort to understand differences in the differential cross sections for excitation of low-lying electronic states determined experimentally by various groups using electronic-vibrational energy-loss spectra of N{sub 2}. In these experiments, very similar spectral unfolding methods were used, which relied on similar Franck-Condon factors. However, the overall analyses of the electron scattering spectra (by the individual groups) resulted in large differences among the differential cross sections determined from thesemore » energy-loss spectra. The transmission response of the experimental apparatus to different-energy scattered electrons has often been discussed as a key factor that caused these disagreements. The present investigation shows in contrast that the effect of transmission is smaller than that required to independently explain such differences, implying that other systematic effects are responsible for the existing differences between measurements.« less

33 CFR 151.2070 - Recordkeeping requirements.

Code of Federal Regulations, 2013 CFR

2013-07-01

..., AND BALLAST WATER Ballast Water Management for Control of Nonindigenous Species in Waters of the... origin of ballast water. This includes date(s), location(s), volume(s) and temperature(s). If a tank has...

46 CFR 162.060-38 - Operation, Maintenance, and Safety Manual (OMSM).

Code of Federal Regulations, 2014 CFR

2014-10-01

... potential effects of the BWMS on the vessel's ballast water, ballast water tanks, and ballast water piping... points, waste or recycling streams, and all sampling points integral to the BWMS; (v) All locations and...

46 CFR 162.060-38 - Operation, Maintenance, and Safety Manual (OMSM).

Code of Federal Regulations, 2012 CFR

2012-10-01

... potential effects of the BWMS on the vessel's ballast water, ballast water tanks, and ballast water piping... points, waste or recycling streams, and all sampling points integral to the BWMS; (v) All locations and...

46 CFR 162.060-38 - Operation, Maintenance, and Safety Manual (OMSM).

Code of Federal Regulations, 2013 CFR

2013-10-01

... potential effects of the BWMS on the vessel's ballast water, ballast water tanks, and ballast water piping... points, waste or recycling streams, and all sampling points integral to the BWMS; (v) All locations and...

Effects of Curriculum and Nonacademic Factors on Undergraduate Electronic Engineering Program Retention

NASA Astrophysics Data System (ADS)

Sulaiman, Munir

Science, technology, engineering, and mathematics (STEM) programs in higher education institutions, particularly engineering programs, face challenges related to recruitment, retention, and graduation rates. The purpose of this study was to determine whether there are significant relationships among students' major preference, academic skills, nonacademic characteristics and perceptions, and retention to year 2 among students in electronic engineering, other STEM, and non STEM majors. The academic skills considered were study habits, intellectual interest, verbal and writing confidence, and academic assistance. The non-academic factors included academic support, family support, financial support, and student social integration into the campus environment. Tinto's theory of retention served as the theoretical framework. The research design was quantitative with a general linear method of analysis using responses to the College Student Inventory (CSI) survey as secondary data to determine the relationships among the independent variables (major and academic and non-academic factors) and dependent variable (retention). Participants were 3,575 first year undergraduate full-time students from three entering classes, 2012 to 2014. Findings suggested that student major and non-academic factors had no effect on student retention, but student study habits and seeking academic assistance were predictors of retention in each of the three groups of majors: engineering, other STEM majors, and nonSTEM majors. Strategies to help increase undergraduate students' study skills and help seeking behaviors may contribute to positive social change at HBCU institutions.

10 CFR 431.286 - Energy conservation standards and their effective dates.

Code of Federal Regulations, 2013 CFR

2013-01-01

... CERTAIN COMMERCIAL AND INDUSTRIAL EQUIPMENT Mercury Vapor Lamp Ballasts Energy Conservation Standards § 431.286 Energy conservation standards and their effective dates. Mercury vapor lamp ballasts, other than specialty application mercury vapor lamp ballasts, shall not be manufactured or imported after...

UV spectrophotometry for monitoring the performance of a yeast-based deoxygenation process to treat ships' ballast water.

PubMed

Veilleux, Éloïse; de Lafontaine, Yves; Thomas, Olivier

2016-04-01

This study assessed the usefulness of UV spectrophotometry for the monitoring of a yeast-based deoxygenation process proposed for ships' ballast water treatment to prevent the transfer of aquatic invasive species. Ten-day laboratory experiments using three treatment concentrations and different water types were conducted and resulted in complete oxygen depletion of treated waters. The treatment performance and quality of treated waters were determined by measuring the UV-visible absorbance spectra of water samples taken over time. Samples were also used for laboratory analysis of water quality properties. The UV absorbance spectra values were strongly correlated (r = 0.96) to yeast cell density in treated waters. The second-order derivative (D (2)) of the spectra varied greatly over time, and the spectrum profiles could be divided into two groups corresponding to the oxygenated and anoxic phases of the treatment. The D (2) value at 215 nm was strongly correlated (r = 0.94) to ammonia levels, which increased over time. The D (2) value at 225 nm was strongly correlated (r > 0.97) to DO concentration. Our results showed that UV spectrophotometry may provide a rapid assessment of the behavior and performance of the yeast bioreactor over time by quantifying (1) the density of yeast cells, (2) the time at which anoxic conditions were reached, and (3) a water quality index of the treated water related to the production of ammonia. We conclude that the rapidity of the technique confers a solid advantage over standard methods used for water quality analysis in laboratory and would permit the direct monitoring of the treatment performance on-board ships.

Dispersion of the electron g factor anisotropy in InAs/InP self-assembled quantum dots

DOE Office of Scientific and Technical Information (OSTI.GOV)

Belykh, V. V., E-mail: vasilii.belykh@tu-dortmund.de; P.N. Lebedev Physical Institute of the Russian Academy of Sciences, Moscow 119991; Yakovlev, D. R.

The electron g factor in an ensemble of InAs/InP quantum dots with emission wavelengths around 1.4 μm is measured using time-resolved pump-probe Faraday rotation spectroscopy in different magnetic field orientations. Thereby, we can extend recent single dot photoluminescence measurements significantly towards lower optical transition energies through 0.86 eV. This allows us to obtain detailed insight into the dispersion of the recently discovered g factor anisotropy in these infrared emitting quantum dots. We find with decreasing transition energy over a range of 50 meV a strong enhancement of the g factor difference between magnetic field normal and along the dot growth axis, namely, frommore » 1 to 1.7. We argue that the g factor cannot be solely determined by the confinement energy, but the dot asymmetry underlying this anisotropy therefore has to increase with increasing dot size.« less

10 CFR 431.329 - Enforcement.

Code of Federal Regulations, 2011 CFR

2011-01-01

... Metal Halide Lamp Ballasts and Fixtures Energy Conservation Standards § 431.329 Enforcement. Process for Metal Halide Lamp Ballasts. This section sets forth procedures DOE will follow in pursuing alleged... with the following statistical sampling procedures for metal halide lamp ballasts, with the methods...

An Analysis of the External Environmental and Internal Organizational Factors Associated with Adoption of the Electronic Health Record

ERIC Educational Resources Information Center

Kruse, Clemens Scott

2013-01-01

Despite a Presidential Order in 2004 that launched national incentives for the use of health information technology, specifically the Electronic Health Record (EHR), adoption of the EHR has been slow. This study attempts to quantify factors associated with adoption of the EHR and Computerized Provider Order Entry (CPOE) by combining multiple…

DFT studies for three Cu(II) coordination polymers: Geometrical and electronic structures, g factors and UV-visible spectra

NASA Astrophysics Data System (ADS)

Ding, Chang-Chun; Wu, Shao-Yi; Xu, Yong-Qiang; Wu, Li-Na; Zhang, Li-Juan

2018-05-01

This work presents a systematic density functional theory (DFT) study for geometrical and electronic structures, g factors and UV-vis spectra of three Cu(II) coordination polymers (CPs) [Cu(XL)(NO3)2]n (1), {[Cu(XL)(4,4‧-bpy)(NO3)2]•CH3CN}n (2) and {[Cu(XL)3](NO3)2·3.5H2O}n (3) based on the ligand N,N‧-bicyclo[2.2.2]oct-7-ene-2,3,5,6-tetracarboxdiimide bi(1,2,4-triazole) (XL) with the linker triazole coordinated with copper to construct the CPs. For three CPs with distinct ligands, the optimized molecular structures with PBE0 hybrid functional and the 6-311g basis set agree well with the corresponding XRD data. Meanwhile, the electronic properties are also analyzed for all the systems. The calculated g factors are found sensitive to the (Hartree-Fock) HF character due to the significant hybridization between copper and ligand orbitals. The calculated UV-visible spectra reveal that the main electronic transitions for CP 1 contain d-d and CT transitions, while those for CPs 2 and 3 largely belong to CT ones. The present CPs seem difficult to adsorb small molecules, e.g., CP 1 with H2O and NO2 exhibit unfavorable adsorption and deformation structures near the Cu2+ site.

Estuarial fingerprinting through multidimensional fluorescence and multivariate analysis.

PubMed

Hall, Gregory J; Clow, Kerin E; Kenny, Jonathan E

2005-10-01

As part of a strategy for preventing the introduction of aquatic nuisance species (ANS) to U.S. estuaries, ballast water exchange (BWE) regulations have been imposed. Enforcing these regulations requires a reliable method for determining the port of origin of water in the ballast tanks of ships entering U.S. waters. This study shows that a three-dimensional fluorescence fingerprinting technique, excitation emission matrix (EEM) spectroscopy, holds great promise as a ballast water analysis tool. In our technique, EEMs are analyzed by multivariate classification and curve resolution methods, such as N-way partial least squares Regression-discriminant analysis (NPLS-DA) and parallel factor analysis (PARAFAC). We demonstrate that classification techniques can be used to discriminate among sampling sites less than 10 miles apart, encompassing Boston Harbor and two tributaries in the Mystic River Watershed. To our knowledge, this work is the first to use multivariate analysis to classify water as to location of origin. Furthermore, it is shown that curve resolution can show seasonal features within the multidimensional fluorescence data sets, which correlate with difficulty in classification.

Institutional Factors for Supporting Electronic Learning Communities

ERIC Educational Resources Information Center

Linton, Jayme N.

2017-01-01

This study was designed to explore how the electronic learning community (eLC) process at an established state virtual high school (SVHS) supported new and veteran online high school teachers through the communities of practice (CoP) framework. Specifically, this study focused on the institutionally-driven nature of the eLC process, using Wenger's…

Epidermal growth factor receptor subunit locations determined in hydrated cells with environmental scanning electron microscopy.

PubMed

Peckys, Diana B; Baudoin, Jean-Pierre; Eder, Magdalena; Werner, Ulf; de Jonge, Niels

2013-01-01

Imaging single epidermal growth factor receptors (EGFR) in intact cells is presently limited by the available microscopy methods. Environmental scanning electron microscopy (ESEM) of whole cells in hydrated state in combination with specific labeling with gold nanoparticles was used to localize activated EGFRs in the plasma membranes of COS7 and A549 cells. The use of a scanning transmission electron microscopy (STEM) detector yielded a spatial resolution of 3 nm, sufficient to identify the locations of individual EGFR dimer subunits. The sizes and distribution of dimers and higher order clusters of EGFRs were determined. The distance between labels bound to dimers amounted to 19 nm, consistent with a molecular model. A fraction of the EGFRs was found in higher order clusters with sizes ranging from 32-56 nm. ESEM can be used for quantitative whole cell screening studies of membrane receptors, and for the study of nanoparticle-cell interactions in general.

Epidermal growth factor receptor subunit locations determined in hydrated cells with environmental scanning electron microscopy

PubMed Central

Peckys, Diana B.; Baudoin, Jean-Pierre; Eder, Magdalena; Werner, Ulf; de Jonge, Niels

2013-01-01

Imaging single epidermal growth factor receptors (EGFR) in intact cells is presently limited by the available microscopy methods. Environmental scanning electron microscopy (ESEM) of whole cells in hydrated state in combination with specific labeling with gold nanoparticles was used to localize activated EGFRs in the plasma membranes of COS7 and A549 cells. The use of a scanning transmission electron microscopy (STEM) detector yielded a spatial resolution of 3 nm, sufficient to identify the locations of individual EGFR dimer subunits. The sizes and distribution of dimers and higher order clusters of EGFRs were determined. The distance between labels bound to dimers amounted to 19 nm, consistent with a molecular model. A fraction of the EGFRs was found in higher order clusters with sizes ranging from 32–56 nm. ESEM can be used for quantitative whole cell screening studies of membrane receptors, and for the study of nanoparticle-cell interactions in general. PMID:24022088

10 CFR 431.282 - Test Procedures [Reserved

Code of Federal Regulations, 2013 CFR

2013-01-01

... EQUIPMENT Mercury Vapor Lamp Ballasts § 431.282 Definitions concerning mercury vapor lamp ballasts. Ballast...) The arc tube wall loading is in excess of 3 Watts/cm2, including such lamps that are mercury vapor, metal halide, and high-pressure sodium lamps. Mercury vapor lamp means a high intensity discharge lamp...

10 CFR 431.282 - Test Procedures [Reserved

Code of Federal Regulations, 2011 CFR

2011-01-01

... EQUIPMENT Mercury Vapor Lamp Ballasts § 431.282 Definitions concerning mercury vapor lamp ballasts. Ballast...) The arc tube wall loading is in excess of 3 Watts/cm2, including such lamps that are mercury vapor, metal halide, and high-pressure sodium lamps. Mercury vapor lamp means a high intensity discharge lamp...

10 CFR 431.282 - Test Procedures [Reserved

Code of Federal Regulations, 2014 CFR

2014-01-01

... EQUIPMENT Mercury Vapor Lamp Ballasts § 431.282 Definitions concerning mercury vapor lamp ballasts. Ballast...) The arc tube wall loading is in excess of 3 Watts/cm2, including such lamps that are mercury vapor, metal halide, and high-pressure sodium lamps. Mercury vapor lamp means a high intensity discharge lamp...

10 CFR 431.282 - Test Procedures [Reserved

Code of Federal Regulations, 2012 CFR

2012-01-01

... EQUIPMENT Mercury Vapor Lamp Ballasts § 431.282 Definitions concerning mercury vapor lamp ballasts. Ballast...) The arc tube wall loading is in excess of 3 Watts/cm2, including such lamps that are mercury vapor, metal halide, and high-pressure sodium lamps. Mercury vapor lamp means a high intensity discharge lamp...

10 CFR 431.327 - Submission of data.

Code of Federal Regulations, 2011 CFR

2011-01-01

... EQUIPMENT Metal Halide Lamp Ballasts and Fixtures Energy Conservation Standards § 431.327 Submission of data.... (2) Each manufacturer or private labeler of a basic model of metal halide lamp ballast shall file a... certification report for each of its metal halide lamp ballast basic models. The certification report (for which...

Validating Smoking Data From the Veteran’s Affairs Health Factors Dataset, an Electronic Data Source

PubMed Central

Brandt, Cynthia A.; Skanderson, Melissa; Justice, Amy C.; Shahrir, Shahida; Butt, Adeel A.; Brown, Sheldon T.; Freiberg, Matthew S.; Gibert, Cynthia L.; Goetz, Matthew Bidwell; Kim, Joon Woo; Pisani, Margaret A.; Rimland, David; Rodriguez-Barradas, Maria C.; Sico, Jason J.; Tindle, Hilary A.; Crothers, Kristina

2011-01-01

Introduction: We assessed smoking data from the Veterans Health Administration (VHA) electronic medical record (EMR) Health Factors dataset. Methods: To assess the validity of the EMR Health Factors smoking data, we first created an algorithm to convert text entries into a 3-category smoking variable (never, former, and current). We compared this EMR smoking variable to 2 different sources of patient self-reported smoking survey data: (a) 6,816 HIV-infected and -uninfected participants in the 8-site Veterans Aging Cohort Study (VACS-8) and (b) a subset of 13,689 participants from the national VACS Virtual Cohort (VACS-VC), who also completed the 1999 Large Health Study (LHS) survey. Sensitivity, specificity, and kappa statistics were used to evaluate agreement of EMR Health Factors smoking data with self-report smoking data. Results: For the EMR Health Factors and VACS-8 comparison of current, former, and never smoking categories, the kappa statistic was .66. For EMR Health Factors and VACS-VC/LHS comparison of smoking, the kappa statistic was .61. Conclusions: Based on kappa statistics, agreement between the EMR Health Factors and survey sources is substantial. Identification of current smokers nationally within the VHA can be used in future studies to track smoking status over time, to evaluate smoking interventions, and to adjust for smoking status in research. Our methodology may provide insights for other organizations seeking to use EMR data for accurate determination of smoking status. PMID:21911825

Coast Guard Maritime Commons

Science.gov Websites

Center's ballast water management system website The Marine Safety Center recently updated two tools posted to its ballast water management system website to assist industry when completing the ballast water management system type approval process, or when accessing letters of intent. 5/23/2018: Release of Mission

Commercial Vessel Compliance « Coast Guard Maritime Commons

Science.gov Websites

updates to Marine Safety Center's ballast water management system website The Marine Safety Center recently updated two tools posted to its ballast water management system website to assist industry when completing the ballast water management system type approval process, or when accessing letters of intent. 5

Electronically cloaked nanoparticles

NASA Astrophysics Data System (ADS)

Shen, Wenqing

The concept of electronic cloaking is to design objects invisible to conduction electrons. The approach of electronic cloaking has been recently suggested to design invisible nanoparticle dopants with electronic scattering cross section smaller than 1% of the physical cross section (pi a2), and therefore to enhance the carrier mobility of bulk materials. The proposed nanoparticles have core-shell structures. The dopants are incorporated inside the core, while the shell layer serves both as a spacer to separate the charge carriers from their parent atoms and as a cloaking shell to minimize the scattering cross section of the electrons from the ionized nanoparticles. Thermoelectric materials are usually highly doped to have enough carrier density. Using invisible dopants could achieve larger thermoelectric power factors by enhancing the electronic mobility. Core-shell nanoparticles show an advantage over one-layer nanoparticles, which are proposed in three-dimensional modulation doping. However designing such nanoparticles is not easy as there are too many parameters to be considered. This thesis first shows an approach to design hollow nanoparticles by applying constrains on variables. In the second part, a simple mapping approach is introduced where one can identify possible core-shell particles by comparing the dimensionless parameters of chosen materials with provided maps. In both parts of this work, several designs with realistic materials were made and proven to achieve electronic cloaking. Improvement in the thermoelectric power factor compared to the traditional impurity doping method was demonstrated in several cases.

Risk factors for manipulation after total knee arthroplasty: a pooled electronic health record database study.

PubMed

Pfefferle, Kiel J; Shemory, Scott T; Dilisio, Matthew F; Fening, Stephen D; Gradisar, Ian M

2014-10-01

A commercially available software platform, Explorys (Explorys, Inc., Cleveland, OH), was used to mine a pooled electronic healthcare database consisting of the medical records of more than 27 million patients. A total of 229,420 patients had undergone a total knee arthroplasty; 3470 (1.51%) patients were identified to have undergone manipulation under anesthesia. Individual risk factors of being female, African American race, age less than 60, BMI >30 and nicotine dependence were determined to have relative risk of 1.25, 2.20, 3.46, 1.33 and 1.32 respectively. Depressive disorder, diabetes mellitus, opioid abuse/dependence and rheumatoid arthritis were not significant risk factors. African Americans under the age of 60 at time of TKA had the greatest incidence of MUA (5.17%) and relative risk of 3.73 (CI: 3.36, 4.13). Copyright © 2014 Elsevier Inc. All rights reserved.

Testing of Performance of a Scroll Pump in Support of Improved Vapor Phase Catalytic Ammonia Removal (VPCAR) Mass Reduction

NASA Technical Reports Server (NTRS)

Nahra, Henry K.; Kraft, Thomas G.; Yee, Glenda F.; Jankovsky, Amy L.; Flynn, Michael

2006-01-01

This paper describes the results of ground testing of a scroll pump with a potential of being a substitute for the current vacuum pump of the Vapor Phase Catalytic Ammonia Reduction (VPCAR). Assessments of the pressure-time, pump-down time, pump power and the pump noise were made for three configurations of the pump the first of which was without the gas ballast, the second with the gas ballast installed but not operating and the third with the gas ballast operating. The tested scroll pump exhibited optimum characteristics given its mass and power requirements. The pump down time required to reach a pressure of 50 Torr ranged from 60 minutes without the ballast to about 120 minutes with the gas ballast operational. The noise emission and the pump power were assessed in this paper as well.

Performance-limiting factors for x-ray free electron laser oscillator as a highly coherent, high spectral purity x-ray source

NASA Astrophysics Data System (ADS)

Park, Gunn Tae

X-ray Free Electron Laser (XFEL) is a light source for coherent X-ray using the radiation from relativistic electrons and interaction between the two. In particular, XFEL oscillator(XFELO) uses optical cavity to repeatedly bring back the radiation to electron beam for the interaction. Its optimal performance, maximum single pass gain and minimum round trip loss, critically depends on cavity optics. In ideal case, the optimal performance would be achieved by the periodic radiation mode maximally overlapping with electron beam while the radiation mode is impinging on curved mirror that gives the radiation the focusing, below critical angle and angular divergence being kept small enough at each crystal for Bragg scattering, which is used for near-normal reflection. In reality, there exist various performance degrading factors in the cavity such as heat load on the crystal surface, misalignments of crystals and mirrors and mirror surface errors. In this thesis, we study via both analytic computation and numerical simulation the optimal design and performance of XFELO cavity in the presence of these factors. In optimal design, we implement asymmetric crystals into cavity to enhance the performance. In general, it has undesirable effect of pulse dilation. We present the configuration that avoids pulse length dilation. Then the effects of misalignments, focal length errors and mirror surface errors are to be evaluated and their tolerances are estimated. In particular, the simulation demonstrates that the effect of mirror surface errors on gain and round trip loss is well-within desired performance of XFELO.

Exploring Factors Affecting Voluntary Adoption of Electronic Medical Records Among Physicians and Clinical Assistants of Small or Solo Private General Practice Clinics.

PubMed

Or, Calvin; Tong, Ellen; Tan, Joseph; Chan, Summer

2018-05-29

The health care reform initiative led by the Hong Kong government's Food and Health Bureau has started the implementation of an electronic sharing platform to provide an information infrastructure that enables public hospitals and private clinics to share their electronic medical records (EMRs) for improved access to patients' health care information. However, previous attempts to convince the private clinics to adopt EMRs to document health information have faced challenges, as the EMR adoption has been voluntary. The lack of electronic data shared by private clinics carries direct impacts to the efficacy of electronic record sharing between public and private healthcare providers. To increase the likelihood of buy-in, it is essential to proactively identify the users' and organizations' needs and capabilities before large-scale implementation. As part of the reform initiative, this study examined factors affecting the adoption of EMRs in small or solo private general practice clinics, by analyzing the experiences and opinions of the physicians and clinical assistants during the pilot implementation of the technology, with the purpose to learn from it before full-scale rollout. In-depth, semistructured interviews were conducted with 23 physicians and clinical assistants from seven small or solo private general practice clinics to evaluate their experiences, expectations, and opinions regarding the deployment of EMRs. Interview transcripts were content analyzed to identify key factors. Factors affecting the adoption of EMRs to record and manage health care information were identified as follows: system interface design; system functions; stability and reliability of hardware, software, and computing networks; financial and time costs; task and outcome performance, work practice, and clinical workflow; physical space in clinics; trust in technology; users' information technology literacy; training and technical support; and social and organizational influences. The

Quantitative structure-retention relationship studies using immobilized artificial membrane chromatography I: amended linear solvation energy relationships with the introduction of a molecular electronic factor.

PubMed

Li, Jie; Sun, Jin; Cui, Shengmiao; He, Zhonggui

2006-11-03

Linear solvation energy relationships (LSERs) amended by the introduction of a molecular electronic factor were employed to establish quantitative structure-retention relationships using immobilized artificial membrane (IAM) chromatography, in particular ionizable solutes. The chromatographic indices, log k(IAM), were determined by HPLC on an IAM.PC.DD2 column for 53 structurally diverse compounds, including neutral, acidic and basic compounds. Unlike neutral compounds, the IAM chromatographic retention of ionizable compounds was affected by their molecular charge state. When the mean net charge per molecule (delta) was introduced into the amended LSER as the sixth variable, the LSER regression coefficient was significantly improved for the test set including ionizable solutes. The delta coefficients of acidic and basic compounds were quite different indicating that the molecular electronic factor had a markedly different impact on the retention of acidic and basic compounds on IAM column. Ionization of acidic compounds containing a carboxylic group tended to impair their retention on IAM, while the ionization of basic compounds did not have such a marked effect. In addition, the extra-interaction with the polar head of phospholipids might cause a certain change in the retention of basic compounds. A comparison of calculated and experimental retention indices suggested that the semi-empirical LSER amended by the addition of a molecular electronic factor was able to reproduce adequately the experimental retention factors of the structurally diverse solutes investigated.

Evaluating efficacy of an environmental policy to prevent biological invasions.

PubMed

Bailey, Sarah A; Deneau, Matthew G; Jean, Laurent; Wiley, Chris J; Leung, Brian; MacIsaac, Hugh J

2011-04-01

Enactment of any environmental policy should be followed by an evaluation of its efficacy to ensure optimal utilization of limited resources, yet measuring the success of these policies can be a challenging task owing to a dearth of data and confounding factors. We examine the efficacy of ballast water policies enacted to prevent biological invasions in the Laurentian Great Lakes. We utilize four criteria to assess the efficacy of this environmental regulation: (1) Is the prescribed management action demonstrably effective? (2) Is the management action effective under operational conditions? (3) Can compliance be achieved on a broad scale? (4) Are desired changes observed in the environment? The four lines of evidence resulting from this analysis indicate that the Great Lakes ballast water management program provides robust, but not complete, protection against ship-mediated biological invasions. Our analysis also indicates that corresponding inspection and enforcement efforts should be undertaken to ensure that environmental policies translate into increased environmental protection. Similar programs could be implemented immediately around the world to protect the biodiversity of the many freshwater ecosystems which receive ballast water discharges by international vessels. This general framework can be extended to evaluate efficacy of other environmental policies.

Integrated Circuit For Simulation Of Neural Network

NASA Technical Reports Server (NTRS)

Thakoor, Anilkumar P.; Moopenn, Alexander W.; Khanna, Satish K.

1988-01-01

Ballast resistors deposited on top of circuit structure. Cascadable, programmable binary connection matrix fabricated in VLSI form as basic building block for assembly of like units into content-addressable electronic memory matrices operating somewhat like networks of neurons. Connections formed during storage of data, and data recalled from memory by prompting matrix with approximate or partly erroneous signals. Redundancy in pattern of connections causes matrix to respond with correct stored data.

The cryo-electron microscopy structure of human transcription factor IIH

DOE PAGES

Greber, Basil J.; Nguyen, Thi Hoang Duong; Fang, Jie; ...

2017-09-13

We report human transcription factor IIH (TFIIH) is part of the general transcriptional machinery required by RNA polymerase II for the initiation of eukaryotic gene transcription. Composed of ten subunits that add up to a molecular mass of about 500 kDa, TFIIH is also essential for nucleotide excision repair. The seven-subunit TFIIH core complex formed by XPB, XPD, p62, p52, p44, p34, and p8 is competent for DNA repair, while the CDK-activating kinase subcomplex, which includes the kinase activity of CDK7 as well as the cyclin H and MAT1 subunits, is additionally required for transcription initiation. Mutations in the TFIIHmore » subunits XPB, XPD, and p8 lead to severe premature ageing and cancer propensity in the genetic diseases xeroderma pigmentosum, Cockayne syndrome, and trichothiodystrophy, highlighting the importance of TFIIH for cellular physiology. Here we present the cryo-electron microscopy structure of human TFIIH at 4.4 Å resolution. The structure reveals the molecular architecture of the TFIIH core complex, the detailed structures of its constituent XPB and XPD ATPases, and how the core and kinase subcomplexes of TFIIH are connected. Also, our structure provides insight into the conformational dynamics of TFIIH and the regulation of its activity.« less

The cryo-electron microscopy structure of human transcription factor IIH

DOE Office of Scientific and Technical Information (OSTI.GOV)

Greber, Basil J.; Nguyen, Thi Hoang Duong; Fang, Jie

We report human transcription factor IIH (TFIIH) is part of the general transcriptional machinery required by RNA polymerase II for the initiation of eukaryotic gene transcription. Composed of ten subunits that add up to a molecular mass of about 500 kDa, TFIIH is also essential for nucleotide excision repair. The seven-subunit TFIIH core complex formed by XPB, XPD, p62, p52, p44, p34, and p8 is competent for DNA repair, while the CDK-activating kinase subcomplex, which includes the kinase activity of CDK7 as well as the cyclin H and MAT1 subunits, is additionally required for transcription initiation. Mutations in the TFIIHmore » subunits XPB, XPD, and p8 lead to severe premature ageing and cancer propensity in the genetic diseases xeroderma pigmentosum, Cockayne syndrome, and trichothiodystrophy, highlighting the importance of TFIIH for cellular physiology. Here we present the cryo-electron microscopy structure of human TFIIH at 4.4 Å resolution. The structure reveals the molecular architecture of the TFIIH core complex, the detailed structures of its constituent XPB and XPD ATPases, and how the core and kinase subcomplexes of TFIIH are connected. Also, our structure provides insight into the conformational dynamics of TFIIH and the regulation of its activity.« less

Limitations of silicon diodes for clinical electron dosimetry.

PubMed

Song, Haijun; Ahmad, Munir; Deng, Jun; Chen, Zhe; Yue, Ning J; Nath, Ravinder

2006-01-01

This work investigates the relevance of several factors affecting the response of silicon diode dosemeters in depth-dose scans of electron beams. These factors are electron energy, instantaneous dose rate, dose per pulse, photon/electron dose ratio and electron scattering angle (directional response). Data from the literature and our own experiments indicate that the impact of these factors may be up to +/-15%. Thus, the different factors would have to cancel out perfectly at all depths in order to produce true depth-dose curves. There are reports of good agreement between depth-doses measured with diodes and ionisation chambers. However, our measurements with a Scantronix electron field detector (EFD) diode and with a plane-parallel ionisation chamber show discrepancies both in the build-up and in the low-dose regions, with a ratio up to 1.4. Moreover, the absolute sensitivity of two diodes of the same EFD model was found to differ by a factor of 3, and this ratio was not constant but changed with depth between 5 and 15% in the low-dose regions of some clinical electron beams. Owing to these inhomogeneities among diodes even of the same model, corrections for each factor would have to be diode-specific and beam-specific. All these corrections would have to be determined using parallel plane chambers, as recommended by AAPM TG-25, which would be unrealistic in clinical practice. Our conclusion is that in general diodes are not reliable in the measurement of depth-dose curves of clinical electron beams.

Evaluation of medication alerts in electronic health records for compliance with human factors principles

PubMed Central

Phansalkar, Shobha; Zachariah, Marianne; Seidling, Hanna M; Mendes, Chantal; Volk, Lynn; Bates, David W

2014-01-01

Introduction Increasing the adoption of electronic health records (EHRs) with integrated clinical decision support (CDS) is a key initiative of the current US healthcare administration. High over-ride rates of CDS alerts strongly limit these potential benefits. As a result, EHR designers aspire to improve alert design to achieve better acceptance rates. In this study, we evaluated drug–drug interaction (DDI) alerts generated in EHRs and compared them for compliance with human factors principles. Methods We utilized a previously validated questionnaire, the I-MeDeSA, to assess compliance with nine human factors principles of DDI alerts generated in 14 EHRs. Two reviewers independently assigned scores evaluating the human factors characteristics of each EHR. Rankings were assigned based on these scores and recommendations for appropriate alert design were derived. Results The 14 EHRs evaluated in this study received scores ranging from 8 to 18.33, with a maximum possible score of 26. Cohen's κ (κ=0.86) reflected excellent agreement among reviewers. The six vendor products tied for second and third place rankings, while the top system and bottom five systems were home-grown products. The most common weaknesses included the absence of characteristics such as alert prioritization, clear and concise alert messages indicating interacting drugs, actions for clinical management, and a statement indicating the consequences of over-riding the alert. Conclusions We provided detailed analyses of the human factors principles which were assessed and described our recommendations for effective alert design. Future studies should assess whether adherence to these recommendations can improve alert acceptance. PMID:24780721

The electronic structure and effective excitonic g factors of GaAs/GaMnAs core-shell nanowires

NASA Astrophysics Data System (ADS)

Li, Dong-Xiao; Xiong, Wen

2017-12-01

We calculate the electronic structures of cylindrical GaAs/GaMnAs core-shell nanowires in the magnetic field based on the eight-band effective-mass kṡp theory, and it is found that the hole states can present strong band-crossings. The probability densities of several lowest electron states and highest hole states at the Γ point are analyzed, and strangely, the distribution of the electron states are more complex than that of the hole states. Furthermore, the components of the electron states will change substantially as the increase of the radius R, which are almost unchanged for the hole states. A very interesting phenomenon is that the effective excitonic g factors gex can be tuned from a large positive value for GaMnAs nanowires to a small negative value for GaAs nanowires, and gex of GaAs nanowires and GaMnAs nanowires will vary slightly and greatly, respectively as the increase of the magnetic field. Meanwhile, we can obtain large gex in cylindrical GaAs/GaMnAs core-shell nanowires when the small magnetic field, the large concentration of manganese ions, the small core radius and the small radius are chosen. Another important result is also found that the radiative intensities of two σ polarized lights can be separated gradually by decreasing the core radius Rc , which can be used to detect two σ polarized lights in the experiment.

Buoyancy Limitation of Filamentous Cyanobacteria under Prolonged Pressure due to the Gas Vesicles Collapse

NASA Astrophysics Data System (ADS)

Abeynayaka, Helayaye Damitha Lakmali; Asaeda, Takashi; Kaneko, Yasuko

2017-08-01

Freshwater cyanobacterium Pseudanabaena galeata were cultured in chambers under artificially generated pressures, which correspond to the hydrostatic pressures at deep water. Variations occurred in gas vesicles volume, and buoyancy state of cells under those conditions were analyzed at different time intervals (5 min, 1 day, and 5 days). Variations in gas vesicles morphology of cells were observed by transmission electron microscopy images. Settling velocity ( Vs) of cells which governs the buoyancy was observed with the aid of a modified optical microscope. Moreover, effects of the prolonged pressure on cell ballast composition (protein and polysaccharides) were examined. Elevated pressure conditions reduced the cell ballast and caused a complete disappearance of gas vesicles in Pseudanabaena galeata cells. Hence cyanobacteria cells were not able to float within the study period. Observations and findings of the study indicate the potential application of hydrostatic pressure, which naturally occurred in hypolimnion of lakes, to inhibit the re-suspension of cyanobacteria cells.

Buoyancy Limitation of Filamentous Cyanobacteria under Prolonged Pressure due to the Gas Vesicles Collapse.