Sample records for factors affecting radiance

  1. Adjusting the tasseled cap brightness and greenness factors for atmospheric path radiance and absorption on a pixel by pixel basis

    NASA Technical Reports Server (NTRS)

    Jackson, R. D.; Slater, P. N.; Pinter, P. J. (Principal Investigator)

    1982-01-01

    A radiative transfer model was used to convert ground measured reflectances into the radiance at the top of the atmosphere, for several levels of atmospheric path radiance. The radiance in MSS7 (0.8 to 1.1 m) was multiplied by the transmission fraction for atmospheres having different levels of precipitable water. The radiance values were converted to simulated LANDSAT digital counts for four path radiance levels and four levels of precipitable water. These values were used to calculate the Kauth-Thomas brightness, greenness, yellowness, and nonsuch factors. Brightness was affected by surface conditions and path radiance. Greenness was affected by surface conditions, path radiance, and precipitable water. Yellowness was affected by path radiance and nonsuch by precipitable water, and both factors changed only slightly with surface conditions. Yellowness and nonsuch were used to adjust brightness and greenness to produce factors that were affected only by surface conditions such as soils and vegetation, and not by path radiance and precipitable water.

  2. Rayleigh, the unit for light radiance.

    PubMed

    Baker, D J

    1974-09-01

    A 0.7% accurate formula is derived for the easy conversion of power spectral radiance L(lambda) in W cm(-2) sr(-1) microm(-1)to rayleigh spectral radiance R(lambda) in rayleigh/microm, R(lambda) = 2pilambdaL(lambda) x 10(13), where the wavelength lambda is in microm. The rationale for the rayleigh unit is discussed in terms of a photon rate factor and a solid angle factor. The latter is developed in terms of an equivalence theorem about optical receivers and extended sources, and the concept is extended to the computation of photon volume emission rates from altitude profiles of zenith radiance.

  3. Modeling and experimental validation of angular radiance and distance-dependent radiance in a turbid medium

    NASA Astrophysics Data System (ADS)

    Liu, Lingling; Li, Chenxi; Zhao, Huijuan; Yi, Xi; Gao, Feng; Meng, Wei; Lu, Yiming

    2014-03-01

    Radiance is sensitive to the variations of tissue optical parameters, such as absorption coefficient μa, scattering coefficient μs, and anisotropy factor g. Therefore, similar to fluence, radiance can be used for tissue characterization. Compared with fluence, radiance has the advantage of offering the direction information of light intensity. Taking such advantage, the optical parameters can be determined by rotating the detector through 360 deg with only a single optode pair. Instead of the translation mode used in the fluence-based technologies, the Rotation mode has less invasiveness in the clinical diagnosis. This paper explores a new method to obtain the optical properties by measuring the distribution of light intensity in liquid phantom with only a single optode pair and the detector rotation through 360 deg. The angular radiance and distance-dependent radiance are verified by comparing experimental measurement data with Monte Carlo (MC) simulation for the short source-detector separations and diffusion approximation for the large source-detector separations. Detecting angular radiance with only a single optode pair under a certain source-detection separation will present a way for prostate diagnose and light dose calculation during the photon dynamic therapy (PDT).

  4. Solar radiance models for determination of ERBE scanner filter factor

    NASA Technical Reports Server (NTRS)

    Arduini, R. F.

    1985-01-01

    Shortwave spectral radiance models for use in the spectral correction algorithms for the ERBE Scanner Instrument are provided. The required data base was delivered to the ERBe Data Reduction Group in October 1984. It consisted of two sets of data files: (1) the spectral bidirectional angular models and (2) the spectral flux modes. The bidirectional models employ the angular characteristics of reflection by the Earth-atmosphere system and were derived from detailed radiance calculations using a finite difference model of the radiative transfer process. The spectral flux models were created through the use of a delta-Eddington model to economically simulate the effects of atmospheric variability. By combining these data sets, a wide range of radiances may be approximated for a number of scene types.

  5. Effect of molecular anisotropy on backscattered ultraviolet radiance.

    PubMed

    Ahmad, Z; Bhartia, P K

    1995-12-20

    The effect of molecular anisotropy on backscattered UV (BUV) radiances is computed by accounting for it in both Rayleigh optical thickness and the scattering-phase matrix. If the effect of molecular anisotropy is included only in the optical thickness and not in the phase matrix, then for high sun (θ(0) ∼ 0°), the nadir radiance (I(0)) leaving the top of the atmosphere is approximately 1.8% higher than the radiance (I(op)) computed with the effect included in the phase matrix. For very low sun (θ(0) > 80°), I(0) is approximately 2.3% lower than I(op). For off-nadir radiances the relative increase (decrease) depends on both the local zenith angle as well as the azimuth angle. Also, an increase in the surface reflectivity decreases the effect of molecular anisotropy on the upwelling radiances. Exclusion of the anisotropy factor in the Rayleigh-phase matrix has very little effect (<1%) on ozone retrieval from the BUV-type instruments. This is because of the ratio technique used in the retrieval algorithm, which practically cancels out the anisotropy effect.

  6. The Impact of Assimilating Precipitation-affected Radiance on Cloud and Precipitation in Goddard WRF-EDAS Analyses

    NASA Technical Reports Server (NTRS)

    Lin, Xin; Zhang, Sara Q.; Zupanski, M.; Hou, Arthur Y.; Zhang, J.

    2015-01-01

    High-frequency TMI and AMSR-E radiances, which are sensitive to precipitation over land, are assimilated into the Goddard Weather Research and Forecasting Model- Ensemble Data Assimilation System (WRF-EDAS) for a few heavy rain events over the continental US. Independent observations from surface rainfall, satellite IR brightness temperatures, as well as ground-radar reflectivity profiles are used to evaluate the impact of assimilating rain-sensitive radiances on cloud and precipitation within WRF-EDAS. The evaluations go beyond comparisons of forecast skills and domain-mean statistics, and focus on studying the cloud and precipitation features in the jointed rainradiance and rain-cloud space, with particular attentions on vertical distributions of height-dependent cloud types and collective effect of cloud hydrometers. Such a methodology is very helpful to understand limitations and sources of errors in rainaffected radiance assimilations. It is found that the assimilation of rain-sensitive radiances can reduce the mismatch between model analyses and observations by reasonably enhancing/reducing convective intensity over areas where the observation indicates precipitation, and suppressing convection over areas where the model forecast indicates rain but the observation does not. It is also noted that instead of generating sufficient low-level warmrain clouds as in observations, the model analysis tends to produce many spurious upperlevel clouds containing small amount of ice water content. This discrepancy is associated with insufficient information in ice-water-sensitive radiances to address the vertical distribution of clouds with small amount of ice water content. Such a problem will likely be mitigated when multi-channel multi-frequency radiances/reflectivity are assimilated over land along with sufficiently accurate surface emissivity information to better constrain the vertical distribution of cloud hydrometers.

  7. Evaluation of the CMODIS-measured radiance

    NASA Astrophysics Data System (ADS)

    Mao, Zhihua; Pan, Delu; Huang, Haiqing

    2006-12-01

    A Chinese Moderate Resolution Imaging Spectrometer (CMODIS) on "Shenzhou-3" spaceship was launched on March 25, 2002. CMODIS has 34 channels, with 30 visible and near-infrared channels and 4 infrared channels. The 30 channels are 20nm width with wavelength ranging from 403nm to 1023nm. The radiance calibration of CMODIS was finished in the laboratory measurements before it was launched and the laboratory calibration coefficients were used to calibrate the CMODIS raw data. Since none of on-board radiance absolute calibration devices including internal lamps system and calibration system which is based on solar reflectance and lunar irradiance were installed with the sensor, how about the accuracy of CMODIS-measured radiance is a key question for the remote sensing data processing and ocean applications. A new model was developed as a program to evaluate the accuracy of calibrated radiance measured by CMODIS at the top of the atmosphere (TOA). The program can compute the Rayleigh scattering radiance and aerosol scattering radiance together with the radiance component from the water-leaving radiance to deduce the total radiance at TOA under some similar observation conditions of CMODIS. Both the multiple-scattering effects and atmosphere absorbing effects are taken into account on the radiative transfer model to improve the accuracy of atmospheric scattering radiances. The model was used to deduce the spectral radiances at TOA and compared with the radiances measured by Sea-viewing Wide Field-of-view Sensor (SeaWiFS) to check the performance of the model, showing that the spectral radiances from the model with small differences from those of SeaWiFS. The spectral radiances of the model can be taken as reference values to evaluate the accuracy of CMODIS calibrated radiance. The relative differences of the two radiances are large from 16% to 300%, especially for CMODIS at the near-infrared channels with more than one time larger than those of the model. It is shown that

  8. Simulating PACE Global Ocean Radiances

    NASA Technical Reports Server (NTRS)

    Gregg, Watson W.; Rousseaux, Cecile S.

    2017-01-01

    The NASA PACE mission is a hyper-spectral radiometer planned for launch in the next decade. It is intended to provide new information on ocean biogeochemical constituents by parsing the details of high resolution spectral absorption and scattering. It is the first of its kind for global applications and as such, poses challenges for design and operation. To support pre-launch mission development and assess on-orbit capabilities, the NASA Global Modeling and Assimilation Office has developed a dynamic simulation of global water-leaving radiances, using an ocean model containing multiple ocean phytoplankton groups, particulate detritus, particulate inorganic carbon (PIC), and chromophoric dissolved organic carbon (CDOC) along with optical absorption and scattering processes at 1 nm spectral resolution. The purpose here is to assess the skill of the dynamic model and derived global radiances. Global bias, uncertainty, and correlation are derived using available modern satellite radiances at moderate spectral resolution. Total chlorophyll, PIC, and the absorption coefficient of CDOC (aCDOC), are simultaneously assimilated to improve the fidelity of the optical constituent fields. A 5-year simulation showed statistically significant (P < 0.05) comparisons of chlorophyll (r = 0.869), PIC (r = 0.868), and a CDOC (r =0.890) with satellite data. Additionally, diatoms (r = 0.890), cyanobacteria (r = 0.732), and coccolithophores (r = 0.716) were significantly correlated with in situ data. Global assimilated distributions of optical constituents were coupled with a radiative transfer model (Ocean-Atmosphere Spectral Irradiance Model, OASIM) to estimate normalized water-leaving radiances at 1 nm for the spectral range 250-800 nm. These unassimilated radiances were within 0.074 mW/sq cm/micron/sr of MODIS-Aqua radiances at 412, 443, 488, 531, 547, and 667 nm. This difference represented a bias of 10.4% (model low). A mean correlation of 0.706 (P < 0.05) was found with global

  9. Carbon dioxide /V2/ radiance results using a new nonequilibrium model

    NASA Astrophysics Data System (ADS)

    Sharma, R. D.; Nadile, R. M.

    1981-01-01

    It was observed during the SPIRE experiment (Spectral Infrared Rocket Experiment) that the 15 micron limb radiance stays constant from 95 to 110 km despite the fact that CO2 concentration over this altitude range decreases by a factor of 20. The results of a 15 micron CO2 radiance model are presented which explain the observed anomaly. It is shown that CO2 deactivation by oxygen is the predominant factor in 15 micron emission above 95 km.

  10. Simulating PACE Global Ocean Radiances

    PubMed Central

    Gregg, Watson W.; Rousseaux, Cécile S.

    2017-01-01

    The NASA PACE mission is a hyper-spectral radiometer planned for launch in the next decade. It is intended to provide new information on ocean biogeochemical constituents by parsing the details of high resolution spectral absorption and scattering. It is the first of its kind for global applications and as such, poses challenges for design and operation. To support pre-launch mission development and assess on-orbit capabilities, the NASA Global Modeling and Assimilation Office has developed a dynamic simulation of global water-leaving radiances, using an ocean model containing multiple ocean phytoplankton groups, particulate detritus, particulate inorganic carbon (PIC), and chromophoric dissolved organic carbon (CDOC) along with optical absorption and scattering processes at 1 nm spectral resolution. The purpose here is to assess the skill of the dynamic model and derived global radiances. Global bias, uncertainty, and correlation are derived using available modern satellite radiances at moderate spectral resolution. Total chlorophyll, PIC, and the absorption coefficient of CDOC (aCDOC), are simultaneously assimilated to improve the fidelity of the optical constituent fields. A 5-year simulation showed statistically significant (P <0.05) comparisons of chlorophyll (r = 0.869), PIC (r = 0.868), and aCDOC (r = 0.890) with satellite data. Additionally, diatoms (r = 0.890), cyanobacteria (r = 0.732), and coccolithophores (r = 0.716) were significantly correlated with in situ data. Global assimilated distributions of optical constituents were coupled with a radiative transfer model (Ocean-Atmosphere Spectral Irradiance Model, OASIM) to estimate normalized water-leaving radiances at 1 nm for the spectral range 250–800 nm. These unassimilated radiances were within −0.074 mW cm−2 μm1 sr−1 of MODIS-Aqua radiances at 412, 443, 488, 531, 547, and 667 nm. This difference represented a bias of −10.4% (model low). A mean correlation of 0.706 (P < 0.05) was found with

  11. Analysis of underwater radiance observations: Apparent optical properties and analytic functions describing the angular radiance distribution

    NASA Astrophysics Data System (ADS)

    Aas, Eyvind; HøJerslev, Niels K.

    1999-04-01

    A primary data set consisting of 70 series of angular radiance distributions observed in clear blue western Mediterranean water and a secondary set of 12 series from the more green and turbid Lake Pend Oreille, Idaho, have been analyzed. The results demonstrate that the main variation of the shape of the downward radiance distribution occurs within the Snell cone. Outside the cone the variation of the shape decreases with increasing zenith angle. The most important shape changes of the upward radiance appear within the zenith angle range 90°-130°. The variation in shape reaches its minimum around nadir, where an almost constant upward radiance distribution implies that a flat sea surface acts like a Lambert emitter within ±8% in the zenith angle interval 140°-180° in air. The ratio Q of upward irradiance and nadir radiance, as well as the average cosines μd and μu for downward and upward radiance, respectively, have rather small standard deviations, ≤10%, within the local water type. In contrast, the irradiance reflectance R has been observed to change up to 400% with depth in the western Mediterranean, while the maximum observed change of Q with depth is only 40%. The dependence of Q on the solar elevation for blue light at 5 m depth in the Mediterranean coincides with observations from the central Atlantic as well as with model computations. The corresponding dependence of μd shows that diffuse light may have a significant influence on its value. Two simple functions describing the observed angular radiance distributions are proposed, and both functions can be determined by two field observations as input parameters. The ɛ function approximates the azimuthal means of downward radiance with an average error ≤7% and of upward radiance with an error of ˜1%. The α function describes the zenith angle dependence of the azimuthal means of upward radiance with an average error ≤7% in clear ocean water, increasing to ≤20% in turbid lake water. The a

  12. Modeling and Assimilating Ocean Color Radiances

    NASA Technical Reports Server (NTRS)

    Gregg, Watson

    2012-01-01

    Radiances are the source of information from ocean color sensors to produce estimates of biological and geochemical constituents. They potentially provide information on various other aspects of global biological and chemical systems, and there is considerable work involved in deriving new information from these signals. Each derived product, however, contains errors that are derived from the application of the radiances, above and beyond the radiance errors. A global biogeochemical model with an explicit spectral radiative transfer model is used to investigate the potential of assimilating radiances. The results indicate gaps in our understanding of radiative processes in the oceans and their relationships with biogeochemical variables. Most important, detritus optical properties are not well characterized and produce important effects of the simulated radiances. Specifically, there does not appear to be a relationship between detrital biomass and its optical properties, as there is for chlorophyll. Approximations are necessary to get beyond this problem. In this reprt we will discuss the challenges in modeling and assimilation water-leaving radiances and the prospects for improving our understanding of biogeochemical process by utilizing these signals.

  13. Measurements of scene spectral radiance variability

    NASA Astrophysics Data System (ADS)

    Seeley, Juliette A.; Wack, Edward C.; Mooney, Daniel L.; Muldoon, Michael; Shey, Shen; Upham, Carolyn A.; Harvey, John M.; Czerwinski, Richard N.; Jordan, Michael P.; Vallières, Alexandre; Chamberland, Martin

    2006-05-01

    Detection performance of LWIR passive standoff chemical agent sensors is strongly influenced by various scene parameters, such as atmospheric conditions, temperature contrast, concentration-path length product (CL), agent absorption coefficient, and scene spectral variability. Although temperature contrast, CL, and agent absorption coefficient affect the detected signal in a predictable manner, fluctuations in background scene spectral radiance have less intuitive consequences. The spectral nature of the scene is not problematic in and of itself; instead it is spatial and temporal fluctuations in the scene spectral radiance that cannot be entirely corrected for with data processing. In addition, the consequence of such variability is a function of the spectral signature of the agent that is being detected and is thus different for each agent. To bracket the performance of background-limited (low sensor NEDN), passive standoff chemical sensors in the range of relevant conditions, assessment of real scene data is necessary1. Currently, such data is not widely available2. To begin to span the range of relevant scene conditions, we have acquired high fidelity scene spectral radiance measurements with a Telops FTIR imaging spectrometer 3. We have acquired data in a variety of indoor and outdoor locations at different times of day and year. Some locations include indoor office environments, airports, urban and suburban scenes, waterways, and forest. We report agent-dependent clutter measurements for three of these backgrounds.

  14. Radiance Data Products at the GES DAAC

    NASA Technical Reports Server (NTRS)

    Savtchenko, A.; Ouzounov, D.; Acker, J.; Johnson, J.; Leptoukh, G.; Qin, J.; Rui, H.; Smith, P.; Teng, W.

    2004-01-01

    The Goddard Earth Sciences Distributed Active Archive Center (GES DAAC) has been archiving and distributing Radiance data, and serving science and application users of these data, for over 10 years now. The user-focused stewardship of the Radiance data from the AIRS, AVHRR, MODIS, SeaWiFS, SORCE, TOMS, TOVS, TRMM, and UARS instruments exemplifies the GES DAAC tradition and experience. Radiance data include raw radiance counts, onboard calibration data, geolocation products, radiometric calibrated and geolocated-calibrated radiance/reflectance. The number of science products archived at the GES DAAC is steadily increasing, as a result of more sophisticated sensors and new science algorithms. Thus, the main challenge for the GES DAAC is to guide users through the variety of Radiance data sets, provide tools to visualize and reduce the volume of the data, and provide uninterrupted access to the data. This presentation will describe the effort at the GES DAAC to build a bridge between multi-sensor data and the effective scientific use of the data, with an emphasis on the heritage of the science products. The intent is to inform users of the existence of this large collection of Radiance data; suggest starting points for cross-platform science projects and data mining activities; provide data services and tools information; and to give expert help in the science data formats and applications.

  15. Radiance and atmosphere propagation-based method for the target range estimation

    NASA Astrophysics Data System (ADS)

    Cho, Hoonkyung; Chun, Joohwan

    2012-06-01

    Target range estimation is traditionally based on radar and active sonar systems in modern combat system. However, the performance of such active sensor devices is degraded tremendously by jamming signal from the enemy. This paper proposes a simple range estimation method between the target and the sensor. Passive IR sensors measures infrared (IR) light radiance radiating from objects in dierent wavelength and this method shows robustness against electromagnetic jamming. The measured target radiance of each wavelength at the IR sensor depends on the emissive properties of target material and is attenuated by various factors, in particular the distance between the sensor and the target and atmosphere environment. MODTRAN is a tool that models atmospheric propagation of electromagnetic radiation. Based on the result from MODTRAN and measured radiance, the target range is estimated. To statistically analyze the performance of proposed method, we use maximum likelihood estimation (MLE) and evaluate the Cramer-Rao Lower Bound (CRLB) via the probability density function of measured radiance. And we also compare CRLB and the variance of and ML estimation using Monte-Carlo.

  16. Intercomparison of Laboratory Radiance Calibration Standards

    NASA Technical Reports Server (NTRS)

    Pavri, Betina; Chrien, Tom; Green, Robert; Williams, Orlesa

    2000-01-01

    Several standards for radiometric calibration were measured repeatedly with a spectroradiometer in order to understand how they compared in accuracy and stability. The tested radiance standards included a NIST 1000 W bulb and halon panel, two calibrated and stabilized integrating spheres, and a cavity blackbody. Results indicate good agreement between the blackbody and 1000 W bulb/spectralon panel, If these two radiance sources are assumed correct, then the integrating spheres did not conform. to their manufacturer-reported radiances in several regions of the spectrum. More detailed measurements am underway to investigate the discrepancy.

  17. An overview of surface radiance and biology studies in FIFE

    NASA Astrophysics Data System (ADS)

    Blad, B. L.; Schimel, D. S.

    1992-11-01

    The use of satellite data to study and to understand energy and mass exchanges between the land surface and the atmosphere requires information about various biological processes and how various reflected or emitted spectral radiances are influenced by or manifested in these processes. To obtain such information, studies were conducted by the First ISLSCP Field Experiment (FIFE) surface radiances and biology (SRB) group using surface, near-surface, helicopter, and aircraft measurements. The two primary objectives of this group were to relate radiative fluxes to biophysical parameters and physiological processes and to assess how various management treatments affect important biological processes. This overview paper summarizes the results obtained by various SRB teams working in nine different areas: (1) measurement of bidirectional reflectance and estimation of hemispherical albedo; (2) evaluation of spatial and seasonal variability of spectral reflectance and vegetation indices; (3) determination of surface and radiational factors and their effects on vegetation indices and PAR relationships; (4) use of surface temperatures to estimate sensible heat flux; (5) controls over photosynthesis and respiration at small scales; (6) soil surface CO2 fluxes and grassland carbon budget; (7) landscape variations in controls over gas exchange and energy partitioning; (8) radiometric response of prairie to management and topography; and (9) determination of nitrogen gas exchanges in a tallgrass prairie.

  18. Wheat signature modeling and analysis for improved training statistics: Supplement. Simulated LANDSAT wheat radiances and radiance components

    NASA Technical Reports Server (NTRS)

    Malila, W. A.; Cicone, R. C.; Gleason, J. M.

    1976-01-01

    Simulated scanner system data values generated in support of LACIE (Large Area Crop Inventory Experiment) research and development efforts are presented. Synthetic inband (LANDSAT) wheat radiances and radiance components were computed and are presented for various wheat canopy and atmospheric conditions and scanner view geometries. Values include: (1) inband bidirectional reflectances for seven stages of wheat crop growth; (2) inband atmospheric features; and (3) inband radiances corresponding to the various combinations of wheat canopy and atmospheric conditions. Analyses of these data values are presented in the main report.

  19. Extraction of Profile Information from Cloud Contaminated Radiances. Appendixes 2

    NASA Technical Reports Server (NTRS)

    Smith, W. L.; Zhou, D. K.; Huang, H.-L.; Li, Jun; Liu, X.; Larar, A. M.

    2003-01-01

    Clouds act to reduce the signal level and may produce noise dependence on the complexity of the cloud properties and the manner in which they are treated in the profile retrieval process. There are essentially three ways to extract profile information from cloud contaminated radiances: (1) cloud-clearing using spatially adjacent cloud contaminated radiance measurements, (2) retrieval based upon the assumption of opaque cloud conditions, and (3) retrieval or radiance assimilation using a physically correct cloud radiative transfer model which accounts for the absorption and scattering of the radiance observed. Cloud clearing extracts the radiance arising from the clear air portion of partly clouded fields of view permitting soundings to the surface or the assimilation of radiances as in the clear field of view case. However, the accuracy of the clear air radiance signal depends upon the cloud height and optical property uniformity across the two fields of view used in the cloud clearing process. The assumption of opaque clouds within the field of view permits relatively accurate profiles to be retrieved down to near cloud top levels, the accuracy near the cloud top level being dependent upon the actual microphysical properties of the cloud. The use of a physically correct cloud radiative transfer model enables accurate retrievals down to cloud top levels and below semi-transparent cloud layers (e.g., cirrus). It should also be possible to assimilate cloudy radiances directly into the model given a physically correct cloud radiative transfer model using geometric and microphysical cloud parameters retrieved from the radiance spectra as initial cloud variables in the radiance assimilation process. This presentation reviews the above three ways to extract profile information from cloud contaminated radiances. NPOESS Airborne Sounder Testbed-Interferometer radiance spectra and Aqua satellite AIRS radiance spectra are used to illustrate how cloudy radiances can be used

  20. Validation of OMI Measured Radiances Over Ice

    NASA Astrophysics Data System (ADS)

    Jaross, G.; Cebula, R. P.; Warner, J.

    2005-12-01

    The Ozone Monitoring Instrument (OMI) was launched aboard the EOS Aura satellite on 15 July, 2004 and has since performed quite well. Calibrated radiances in the form of Level 1 data products are produced regularly every orbit with minimal data loss. A total of 12 atmospheric constituent data products are currently planned for the OMI science data processing. All rely, to varying degrees, on the sun-normalized radiances of the OMI sensor. Retrievals of atmospheric trace constituents, such as NO{}_2, BrO, OCLO, and HCHO, rely upon spectroscopy and tend to be insensitive to errors in the absolute radiance levels. But column O{}_3 amount, aerosol properties, cloud heights, and UV surface radiation have significant sensitivities to changes in the sun-normalized radiances. In this presentation we discuss our evaluation of the OMI sun-normalized radiances between 330 nm and 500 nm. This covers most of the OMI spectral range where ozone absorption is small. Our technique involves a comparison of normalized radiances measured by OMI over the Antarctic continent with top-of-the-atmosphere (TOA) values computed with a radiative transfer model. In our model we assume a Rayleigh-scattering, aerosol-free, cloud-free atmosphere, and a mean surface reflectance derived from measurements on the ground. TOA radiances are sensitive to the bi-directional distribution of surface reflectance, especially at high solar zenith angles. We have developed a surface reflectance model to help correct these effects, but it still remains the largest source of uncertainty. We estimate the residual uncertainty at all wavelengths to be 2%.

  1. The direct assimilation of cloud-affected satellite infrared radiance in the NCEP 3D-Hybrid system

    NASA Astrophysics Data System (ADS)

    Zhang, X.

    2016-12-01

    A function has been developed in NCEP 3D-Hybrid system to make use of Infrared radiances from Spinning Enhanced Visible and Infrared Imager (SEVIRI) on Meteosat-10(MSG-10) satellite in overcast cloudy conditions where effective cloud fractions were greater than 0.9. These cloudy radiances provide new information that currently assimilated in clear-sky condition from SEVIRI MSG-10. The model state vector is locally extended at observation locations, to include cloud top pressure as cloud parameters. This parameter describing a single-layer cloud are simultaneously estimated together with temperature and humidity inside the main analysis. Assimilation experiments have been run with the new scheme in which overcast radiance from SEVIRI MSG-10 are used in addition to the available clear-sky data. Two water vapor channels ( 6.2 and 7.3μm) and window channels (8.5, 11.2, 12.3 and 13.3μm) from SEVIRI MSG-10 are assimilated in the experiments. The overcast data locations typically represent 10% or less of the total due to the application of stringent quality control. However, The extra data that are used give rise to modified increments (largest for temperature and humidity) at and above the diagnosed cloud top. Also it improves the analysis fit to independent radiosonde observations and results in some small, but statistically significant, improvements in forecast quality.

  2. Uncertainty in cloud optical depth estimates made from satellite radiance measurements

    NASA Technical Reports Server (NTRS)

    Pincus, Robert; Szczodrak, Malgorzata; Gu, Jiujing; Austin, Philip

    1995-01-01

    The uncertainty in optical depths retrieved from satellite measurements of visible wavelength radiance at the top of the atmosphere is quantified. Techniques are briefly reviewed for the estimation of optical depth from measurements of radiance, and it is noted that these estimates are always more uncertain at greater optical depths and larger solar zenith angles. The lack of radiometric calibration for visible wavelength imagers on operational satellites dominates the uncertainty retrievals of optical depth. This is true for both single-pixel retrievals and for statistics calculated from a population of individual retrievals. For individual estimates or small samples, sensor discretization can also be significant, but the sensitivity of the retrieval to the specification of the model atmosphere is less important. The relative uncertainty in calibration affects the accuracy with which optical depth distributions measured by different sensors may be quantitatively compared, while the absolute calibration uncertainty, acting through the nonlinear mapping of radiance to optical depth, limits the degree to which distributions measured by the same sensor may be distinguished.

  3. Platform and Environmental Effects on Above- and In-Water Determinations of Water-Leaving Radiances

    NASA Technical Reports Server (NTRS)

    Hooker, Stanford B.; Morel, Andre; McClain, Charles R. (Technical Monitor)

    2001-01-01

    A comparison of above- and in-water spectral measurements in Case-1 conditions showed the uncertainty in above-water determinations of water-leaving radiances depended on the pointing angle of the above-water instruments with respect to the side of the ship. Two above-water methods were used to create a diagnostic variable to quantify the presence of superstructure reflections which degraded the above-water intracomparisons of water-leaving radiances by 10.9-33.4% (for far-to-near viewing distances, respectively). The primary conclusions of the above- and in-water intercomparison of water-leaving radiances were as follows: a) the SeaWiFS 5% radiometric objective was achieved with the above-water approach, but reliably with only one method and only for about half the data; b) a decrease in water-leaving radiance values was seen in the presence of swell, although, wave crests were radiometrically brighter than the troughs; and c) standard band ratios used in ocean color algorithms remained severely affected, because of the relatively low signal and, thus, proportionally significant contamination at the 555nm wavelength.

  4. View-angle-dependent AIRS Cloudiness and Radiance Variance: Analysis and Interpretation

    NASA Technical Reports Server (NTRS)

    Gong, Jie; Wu, Dong L.

    2013-01-01

    Upper tropospheric clouds play an important role in the global energy budget and hydrological cycle. Significant view-angle asymmetry has been observed in upper-level tropical clouds derived from eight years of Atmospheric Infrared Sounder (AIRS) 15 um radiances. Here, we find that the asymmetry also exists in the extra-tropics. It is larger during day than that during night, more prominent near elevated terrain, and closely associated with deep convection and wind shear. The cloud radiance variance, a proxy for cloud inhomogeneity, has consistent characteristics of the asymmetry to those in the AIRS cloudiness. The leading causes of the view-dependent cloudiness asymmetry are the local time difference and small-scale organized cloud structures. The local time difference (1-1.5 hr) of upper-level (UL) clouds between two AIRS outermost views can create parts of the observed asymmetry. On the other hand, small-scale tilted and banded structures of the UL clouds can induce about half of the observed view-angle dependent differences in the AIRS cloud radiances and their variances. This estimate is inferred from analogous study using Microwave Humidity Sounder (MHS) radiances observed during the period of time when there were simultaneous measurements at two different view-angles from NOAA-18 and -19 satellites. The existence of tilted cloud structures and asymmetric 15 um and 6.7 um cloud radiances implies that cloud statistics would be view-angle dependent, and should be taken into account in radiative transfer calculations, measurement uncertainty evaluations and cloud climatology investigations. In addition, the momentum forcing in the upper troposphere from tilted clouds is also likely asymmetric, which can affect atmospheric circulation anisotropically.

  5. Correction for reflected sky radiance in low-altitude coastal hyperspectral images.

    PubMed

    Kim, Minsu; Park, Joong Yong; Kopilevich, Yuri; Tuell, Grady; Philpot, William

    2013-11-10

    Low-altitude coastal hyperspectral imagery is sensitive to reflections of sky radiance at the water surface. Even in the absence of sun glint, and for a calm water surface, the wide range of viewing angles may result in pronounced, low-frequency variations of the reflected sky radiance across the scan line depending on the solar position. The variation in reflected sky radiance can be obscured by strong high-spatial-frequency sun glint and at high altitude by path radiance. However, at low altitudes, the low-spatial-frequency sky radiance effect is frequently significant and is not removed effectively by the typical corrections for sun glint. The reflected sky radiance from the water surface observed by a low-altitude sensor can be modeled in the first approximation as the sum of multiple-scattered Rayleigh path radiance and the single-scattered direct-solar-beam radiance by the aerosol in the lower atmosphere. The path radiance from zenith to the half field of view (FOV) of a typical airborne spectroradiometer has relatively minimal variation and its reflected radiance to detector array results in a flat base. Therefore the along-track variation is mostly contributed by the forward single-scattered solar-beam radiance. The scattered solar-beam radiances arrive at the water surface with different incident angles. Thus the reflected radiance received at the detector array corresponds to a certain scattering angle, and its variation is most effectively parameterized using the downward scattering angle (DSA) of the solar beam. Computation of the DSA must account for the roll, pitch, and heading of the platform and the viewing geometry of the sensor along with the solar ephemeris. Once the DSA image is calculated, the near-infrared (NIR) radiance from selected water scan lines are compared, and a relationship between DSA and NIR radiance is derived. We then apply the relationship to the entire DSA image to create an NIR reference image. Using the NIR reference image

  6. Inference of cirrus cloud properties using satellite-observed visible and infrared radiances. I - Parameterization of radiance fields

    NASA Technical Reports Server (NTRS)

    Minnis, Patrick; Liou, Kuo-Nan; Takano, Yoshihide

    1993-01-01

    The impact of using phase functions for spherical droplets and hexagonal ice crystals to analyze radiances from cirrus is examined. Adding-doubling radiative transfer calculations are employed to compute radiances for different cloud thicknesses and heights over various backgrounds. These radiances are used to develop parameterizations of top-of-the-atmosphere visible reflectance and IR emittance using tables of reflectances as a function of cloud optical depth, viewing and illumination angles, and microphysics. This parameterization, which includes Rayleigh scattering, ozone absorption, variable cloud height, and an anisotropic surface reflectance, reproduces the computed top-of-the-atmosphere reflectances with an accruacy of +/- 6 percent for four microphysical models: 10-micron water droplet, small symmetric crystal, cirrostratus, and cirrus uncinus. The accuracy is twice that of previous models.

  7. Theory of spectral radiance of pollutants at sea

    NASA Technical Reports Server (NTRS)

    1978-01-01

    Remote measurement of soluble pollutants that change the color of the water in the sea is reported. The sensor is a spectral radiometer that flies over the polluted area and compares its spectral radiance to that of surrounding clean seawater. A quantitative analysis of the concentration of pollutants using the measured radiance of the sea compared to laboratory measurements of reflection and transmission spectra of the pollutants is presented. The quantities involved are defined and means for measuring them are described. The equations for remote sensing with a low-flying aircraft, in which case the absorption and radiance of intervening air is negligible are derived. High-flying aircraft and satellites, in which case the radiance of intervening air is the major problem are applied.

  8. 'Florida Radiance' strawberry

    USDA-ARS?s Scientific Manuscript database

    'Florida Radiance' strawberry (Fragaria xananassa Duch.) is a new strawberry cultivar released by the University of Florida. It appears to be a good cultivar to complement the current commercial cultivar 'Strawberry Festival' during the early part of the production season as its yields are higher wh...

  9. Atmospheric radiance interpolation for the modeling of hyperspectral data

    NASA Astrophysics Data System (ADS)

    Fuehrer, Perry; Healey, Glenn; Rauch, Brian; Slater, David; Ratkowski, Anthony

    2008-04-01

    The calibration of data from hyperspectral sensors to spectral radiance enables the use of physical models to predict measured spectra. Since environmental conditions are often unknown, material detection algorithms have emerged that utilize predicted spectra over ranges of environmental conditions. The predicted spectra are typically generated by a radiative transfer (RT) code such as MODTRAN TM. Such techniques require the specification of a set of environmental conditions. This is particularly challenging in the LWIR for which temperature and atmospheric constituent profiles are required as inputs for the RT codes. We have developed an automated method for generating environmental conditions to obtain a desired sampling of spectra in the sensor radiance domain. Our method provides a way of eliminating the usual problems encountered, because sensor radiance spectra depend nonlinearly on the environmental parameters, when model conditions are specified by a uniform sampling of environmental parameters. It uses an initial set of radiance vectors concatenated over a set of conditions to define the mapping from environmental conditions to sensor spectral radiance. This approach enables a given number of model conditions to span the space of desired radiance spectra and improves both the accuracy and efficiency of detection algorithms that rely upon use of predicted spectra.

  10. Disk and circumsolar radiances in the presence of ice clouds

    DOE PAGES

    Haapanala, Päivi; Räisänen, Petri; McFarquhar, Greg M.; ...

    2017-06-12

    The impact of ice clouds on solar disk and circumsolar radiances is investigated using a Monte Carlo radiative transfer model. The monochromatic direct and diffuse radiances are simulated at angles of 0 to 8° from the center of the sun. Input data for the model are derived from measurements conducted during the 2010 Small Particles in Cirrus (SPARTICUS) campaign together with state-of-the-art databases of optical properties of ice crystals and aerosols. For selected cases, the simulated radiances are compared with ground-based radiance measurements obtained by the Sun and Aureole Measurements (SAM) instrument. First, the sensitivity of the radiances to themore » ice cloud properties and aerosol optical thickness is addressed. The angular dependence of the disk and circumsolar radiances is found to be most sensitive to assumptions about ice crystal roughness (or, more generally, non-ideal features of ice crystals) and size distribution, with ice crystal habit playing a somewhat smaller role. Second, in comparisons with SAM data, the ice cloud optical thickness is adjusted for each case so that the simulated radiances agree closely (i.e., within 3 %) with the measured disk radiances. Circumsolar radiances at angles larger than ≈ 3° are systematically underestimated when assuming smooth ice crystals, whereas the agreement with the measurements is better when rough ice crystals are assumed. In conclusion, our results suggest that it may well be possible to infer the particle roughness directly from ground-based SAM measurements. In addition, the results show the necessity of correcting the ground-based measurements of direct radiation for the presence of diffuse radiation in the instrument's field of view, in particular in the presence of ice clouds.« less

  11. A Systematic Error Correction Method for TOVS Radiances

    NASA Technical Reports Server (NTRS)

    Joiner, Joanna; Rokke, Laurie; Einaudi, Franco (Technical Monitor)

    2000-01-01

    Treatment of systematic errors is crucial for the successful use of satellite data in a data assimilation system. Systematic errors in TOVS radiance measurements and radiative transfer calculations can be as large or larger than random instrument errors. The usual assumption in data assimilation is that observational errors are unbiased. If biases are not effectively removed prior to assimilation, the impact of satellite data will be lessened and can even be detrimental. Treatment of systematic errors is important for short-term forecast skill as well as the creation of climate data sets. A systematic error correction algorithm has been developed as part of a 1D radiance assimilation. This scheme corrects for spectroscopic errors, errors in the instrument response function, and other biases in the forward radiance calculation for TOVS. Such algorithms are often referred to as tuning of the radiances. The scheme is able to account for the complex, air-mass dependent biases that are seen in the differences between TOVS radiance observations and forward model calculations. We will show results of systematic error correction applied to the NOAA 15 Advanced TOVS as well as its predecessors. We will also discuss the ramifications of inter-instrument bias with a focus on stratospheric measurements.

  12. Using Medtronic's MAST Quadrant, Radiance, and Radiance X Illumination Systems with high-power light sources increases burn risk.

    PubMed

    2010-11-01

    Connecting the Medtronic MAST Quadrant Illumination System, Radiance Illumination System, or Radiance X Illumination System--all of which are specialized fiberoptic light cables used with the company's minimally invasive spinal products--to a high-power surgical light source significantly increases the risk of patient burns. Hospitals should ensure that the products are used only with 100 W light sources and 5 mm light cables, as prescribed in the product labeling.

  13. Spectral Radiance of a Large-Area Integrating Sphere Source

    PubMed Central

    Walker, James H.; Thompson, Ambler

    1995-01-01

    The radiance and irradiance calibration of large field-of-view scanning and imaging radiometers for remote sensing and surveillance applications has resulted in the development of novel calibration techniques. One of these techniques is the employment of large-area integrating sphere sources as radiance or irradiance secondary standards. To assist the National Aeronautical and Space Administration’s space based ozone measurement program, a commercially available large-area internally illuminated integrating sphere source’s spectral radiance was characterized in the wavelength region from 230 nm to 400 nm at the National Institute of Standards and Technology. Spectral radiance determinations and spatial mappings of the source indicate that carefully designed large-area integrating sphere sources can be measured with a 1 % to 2 % expanded uncertainty (two standard deviation estimate) in the near ultraviolet with spatial nonuniformities of 0.6 % or smaller across a 20 cm diameter exit aperture. A method is proposed for the calculation of the final radiance uncertainties of the source which includes the field of view of the instrument being calibrated. PMID:29151725

  14. The Intercalibration of Geostationary Visible Imagers Using Operational Hyperspectral SCIAMACHY Radiances

    NASA Technical Reports Server (NTRS)

    Doelling, David R.; Scarino, Benjamin R.; Morstad, Daniel; Gopalan, Arun; Bhatt, Rajendra; Lukashin, Constantine; Minnis, Patrick

    2013-01-01

    Spectral band differences between sensors can complicate the process of intercalibration of a visible sensor against a reference sensor. This can be best addressed by using a hyperspectral reference sensor whenever possible because they can be used to accurately mitigate the band differences. This paper demonstrates the feasibility of using operational Scanning Imaging Absorption Spectrometer for Atmospheric Cartography (SCIAMACHY) large-footprint hyperspectral radiances to calibrate geostationary Earth-observing (GEO) sensors. Near simultaneous nadir overpass measurements were used to compare the temporal calibration of SCIAMACHY with Aqua Moderate Resolution Imaging Spectroradiometer band radiances, which were found to be consistent to within 0.44% over seven years. An operational SCIAMACHY/GEO ray-matching technique was presented, along with enhancements to improve radiance pair sampling. These enhancements did not bias the underlying intercalibration and provided enough sampling to allow up to monthly monitoring of the GEO sensor degradation. The results of the SCIAMACHY/GEO intercalibration were compared with other operational four-year Meteosat-9 0.65-µm calibration coefficients and were found to be within 1% of the gain, and more importantly, it had one of the lowest temporal standard errors of all the methods. This is more than likely that the GEO spectral response function could be directly applied to the SCIAMACHY radiances, whereas the other operational methods inferred a spectral correction factor. This method allows the validation of the spectral corrections required by other methods.

  15. Evaluation and Assimilation of Cloud Cleared Radiances for AIRS in GEOS-5

    NASA Technical Reports Server (NTRS)

    Liu, Hui-chun

    2008-01-01

    The use of clear (cloud-free) channels for AIRS in GEOS-5 had shown positive impact on forecast skills in both hemispheres. However, improvements in forecast skills due to the assimilation of AIRS data are less impressive since the number of assimilated channels from AIRS is much larger than that from other Infrared sounders such as HIRS-3 onboard NOAA 15-17 satellites. This limitation of AIRS radiance data to improve the forecast skill is mainly due to the fact that channels capable of peaking below clouds are not used in the assimilation and yet those have highest vertical resolving capability of AIRS instrument are concentrated in the lower troposphere. On average, the percentage of AIRS footprints completely clear for all channels is less than 10%. The percentage of assimilated AIRS channel radiances however ranges from 100% for channels peaking in the upper stratosphere, above the cloud, to no more that 5% in the lower atmosphere due to cloud contamination. Our current ability to model and predict clouds accurately in global model, and to fully characterize and parameterize optical properties of cloud particles in radiative transfer model are the two major obstacles prohibiting us to use cloudy radiance directly in the assimilation. To further improve forecast skill using AIRS data, we ought to use the channels peaking below the clouds in the troposphere, which can be accomplished by assimilating cloud-cleared radiance. The cloud-cleared radiance data for AIRS used in this study were obtained from optimal cloud clearing procedures developed by researchers at CIMSS of University of Wisconsin at Madison to retrieve clear column radiances for all AIRS channels by collocating multi-band MODIS IR clear radiance observations with the AIRS cloudy radiances on a single footprint basis. Two adjacent AIRS cloudy footprints are used to retrieve one AIRS cloud-cleared radiance spectrum and no background information (first guess) is needed. To assimilate the cloud

  16. Ground-based determination of atmospheric radiance for correction of ERTS-1 data

    NASA Technical Reports Server (NTRS)

    Peacock, K.

    1974-01-01

    A technique is described for estimating the atmospheric radiance observed by a downward sensor (ERTS) using ground-based measurements. A formula is obtained for the sky radiance at the time of the ERTS overpass from the radiometric measurement of the sky radiance made at a particular solar zenith angle and air mass. A graph illustrates ground-based sky radiance measurements as a function of the scattering angle for a range of solar air masses. Typical values for sky radiance at a solar zenith angle of 48 degrees are given.

  17. Radiance limits of ceramic phosphors under high excitation fluxes

    NASA Astrophysics Data System (ADS)

    Lenef, Alan; Kelso, John; Zheng, Yi; Tchoul, Maxim

    2013-09-01

    Ceramic phosphors, excited by high radiance pump sources, offer considerable potential for high radiance conversion. Interestingly, thermodynamic arguments suggest that the radiance of the luminescent spot can even exceed that of the incoming light source. In practice, however, thermal quenching and (non-thermal) optical saturation limit the maximum attainable radiance of the luminescent source. We present experimental data for Ce:YAG and Ce:GdYAG ceramics in which these limits have been investigated. High excitation fluxes are achieved using laser pumping. Optical pumping intensities exceeding 100W/mm2 have been shown to produce only modest efficiency depreciation at low overall pump powers because of the short Ce3+ lifetime, although additional limitations exist. When pump powers are higher, heat-transfer bottlenecks within the ceramic and heat-sink interfaces limit maximum pump intensities. We find that surface temperatures of these laser-pumped ceramics can reach well over 150°C, causing thermal-quenching losses. We also find that in some cases, the loss of quantum efficiency with increasing temperature can cause a thermal run-away effect, resulting in a rapid loss in converted light, possibly over-heating the sample or surrounding structures. While one can still obtain radiances on the order of many W/mm2/sr, temperature quenching effects ultimately limit converted light radiance. Finally, we use the diffusion-approximation radiation transport models and rate equation models to simulate some of these nonlinear optical pumping and heating effects in high-scattering ceramics.

  18. Assimilation of the Microwave Limb Sounder Radiances

    NASA Technical Reports Server (NTRS)

    Wargan, K.; Read, W.; Livesey, N.; Wagner, P.; Nguyen. H.; Pawson, S.

    2012-01-01

    It has been shown that the assimilation of limb-sounder data can significantly improve the representation of ozone in NASA's GEOS Data Assimilation Systems (GEOS-DAS), particularly in the stratosphere. The studies conducted so far utilized retrieved data from the MIPAS, POAM, ILAS and EOS Microwave Limb Sounder (EOS MLS) instruments. Direct assimilation of the radiance data can be seen as the natural next step to those studies. The motivation behind working with radiances is twofold. First, retrieval algorithms use a priori data which are either climatological or are obtained from previous analyses. This introduces additional uncertainty and, in some cases, may lead to "self-contamination"- when the a priori is taken from the same assimilation system in which subsequently ingests the retrieved observations. Second, radiances can be available in near real time thus providing an opportunity for operational assimilation, which could help improve the use of infrared radiance instruments from operational satellite instruments. In this presentation we summarize our ongoing work on an implementation of the assimilation of EOS MLS radiances into the GEOS-5 DAS. This work focuses on assimilation of band 7 brightness temperatures which are sensitive to ozone. Our implementation uses the MLS Callable Forward Model developed by the MLS team at NASA JPL as the observation operator. We will describe our approach and recent results which are not yet final. In particular, we will demonstrate that this approach has a potential to improve the vertical structure of ozone in the lower tropical stratosphere as compared with the retrieved MLS product. We will discuss the computational efficiency of this implementation.

  19. Asymptotic radiance and polarization in optically thick media: ocean and clouds.

    PubMed

    Kattawar, G W; Plass, G N

    1976-12-01

    Deep in a homogeneous medium that both scatters and absorbs photons, such as a cloud, the ocean, or a thick planetary atmosphere, the radiance decreases exponentially with depth, while the angular dependence of the radiance and polarization is independent of depth. In this diffusion region, the asymptotic radiance and polarization are also independent of the incident distribution of radiation at the upper surface of the medium. An exact expression is derived for the asymptotic radiance and polarization for Rayleigh scattering. The approximate expression for the asymptotic radiance derived from the scalar theory is shown to be in error by as much as 16.4%. An exact expression is also derived for the relation between the diffusion exponent k and the single scattering albedo. A method is developed for the numerical calculation of the asymptotic radiance and polarization for any scattering matrix. Results are given for scattering from the haze L and cloud C3 distributions for a wide range of single scattering albedos. When the absorption is large, the polarization in the diffusion region approaches the values obtained for single scattered photons, while the radiance approaches the value calculated from the expression: phase function divided by (1 + kmicro), where micro is the cosine of the zenith angle. The asymptotic distribution of the radiation is of interest since it depends only on the inherent optical properties of the medium. It is, however, difficult to observe when the absorption is large because of the very low radiance values in the diffusion region.

  20. Modeling the Radiance of the Moon for On-orbit Calibration

    USGS Publications Warehouse

    Stone, T.C.; Kieffer, H.H.; Becker, K.J.; ,

    2003-01-01

    The RObotic Lunar Observatory (ROLO) project has developed radiometric models of the Moon for disk-integrated irradiance and spatially resolved radiance. Although the brightness of the Moon varies spatially and with complex dependencies upon illumination and viewing geometry, the surface photometric properties are extremely stable, and therefore potentially knowable to high accuracy. The ROLO project has acquired 5+ years of spatially resolved lunar images in 23 VNIR and 9 SWIR filter bands at phase angles up to 90??. These images are calibrated to exoatmospheric radiance using nightly stellar observations in a band-coupled extinction algorithm and a radiometric scale based upon observations of the star Vega. An effort is currently underway to establish an absolute scale with direct traceability to NIST radiometric standards. The ROLO radiance model performs linear fitting of the spatially resolved lunar image data on an individual pixel basis. The results are radiance images directly comparable to spacecraft observations of the Moon. Model-generated radiance images have been produced for the ASTER lunar view conducted on 14 April 2003. The radiance model is still experimental - simplified photometric functions have been used, and initial results show evidence of computational instabilities, particularly at the lunar poles. The ROLO lunar image dataset is unique and extensive and presents opportunities for development of novel approaches to lunar photometric modeling.

  1. Directional radiance measurements: Challenges in the sampling of landscapes

    NASA Technical Reports Server (NTRS)

    Deering, D. W.

    1994-01-01

    Most earth surfaces, particularly those supporting natural vegetation ecosystems, constitute structurally and spectrally complex surfaces that are distinctly non-Lambertian reflectors. Obtaining meaningful measurements of the directional radiances of landscapes and obtaining estimates of the complete bidirectional reflectance distribution functions of ground targets with complex and variable landscape and radiometric features are challenging tasks. Reasons for the increased interest in directional radiance measurements are presented, and the issues that must be addressed when trying to acquire directional radiances for vegetated land surfaces from different types of remote sensing platforms are discussed. Priority research emphases are suggested, concerning field measurements of directional surface radiances and reflectances for future research. Primarily, emphasis must be given to the acquisition of more complete and directly associated radiometric and biometric parameter data sets that will empower the exploitation of the 'angular dimension' in remote sensing of vegetation through enabling the further development and rigorous validation of state of the art plant canopy models.

  2. Process of preparing metal parts to be heated by means of infrared radiance

    DOEpatents

    Mayer, Howard Robinson [Cincinnati, OH; Blue, Craig A [Knoxville, TN

    2009-06-09

    A method for preparing metal for heating by infrared radiance to enable uniform and consistent heating. The surface of one or more metal parts, such as aluminum or aluminum alloy parts, is treated to alter the surface finish to affect the reflectivity of the surface. The surface reflectivity is evaluated, such as by taking measurements at one or more points on the surface, to determine if a desired reflectivity has been achieved. The treating and measuring are performed until the measuring indicates that the desired reflectivity has been achieved. Once the treating has altered the surface finish to achieve the desired reflectivity, the metal part may then be exposed to infrared radiance to heat the metal part to a desired temperature, and that heating will be substantially consistent throughout by virtue of the desired reflectivity.

  3. Clear water radiances for atmospheric correction of coastal zone color scanner imagery

    NASA Technical Reports Server (NTRS)

    Gordon, H. R.; Clark, D. K.

    1981-01-01

    The possibility of computing the inherent sea surface radiance for regions of clear water from coastal zone color scanner (CZCS) imagery given only a knowledge of the local solar zenith angle is examined. The inherent sea surface radiance is related to the upwelling and downwelling irradiances just beneath the sea surface, and an expression is obtained for a normalized inherent sea surface radiance which is nearly independent of solar zenith angle for low phytoplankton pigment concentrations. An analysis of a data base consisting of vertical profiles of upwelled spectral radiance and pigment concentration, which was used in the development of the CZCS program, confirms the virtual constancy of the normalized inherent sea surface radiance at wavelengths of 520 and 550 nm for cases when the pigment concentration is less than 0.25 mg/cu m. A strategy is then developed for using the normalized inherent sea surface radiance in the atmospheric correction of CZCS imagery.

  4. A semianalytic radiance model of ocean color

    NASA Technical Reports Server (NTRS)

    Gordon, Howard R.; Brown, James W.; Brown, Otis B.; Evans, Robert H.; Smith, Raymond C.

    1988-01-01

    A semianalytical radiance model is developed which predicts the upwelled spectral radiance at the sea surface as a function of the phytoplankton pigment concentration for Morel Case 1 waters. The model is in good agreement with experimental measurements carried out in waters which were not included in the data base used to derive it. It suggests that the observed variability in the radiance is due to variations in the backscattering of plankton and the associated detrital material. The model is extended to include other material in the water, such as dissolved organic material, referred to as yellow substances, and detached coccoliths from coccolithophorids, e.g., Emiliana huxleyi. Potential applications include an improved biooptical algorithm for the retrieval of pigment concentrations from satellite imagery in the presence of interference from detached coccoliths and an improved atmospheric correction for satellite imagery. The model also serves to identify and to interpret deviations from Case 1 waters.

  5. The spectral amplification effect of clouds to the night sky radiance in Madrid

    NASA Astrophysics Data System (ADS)

    Aubé, M.; Kocifaj, M.; Zamorano, J.; Solano Lamphar, H. A.; Sanchez de Miguel, A.

    2016-09-01

    Artificial Light at Night (ALAN) may have various environmental impacts ranging from compromising the visibility of astronomical objects to the perturbation of circadian cycles in animals and humans. In the past much research has been carried out to study the impact of ALAN on the radiance of the night sky during clear sky conditions. This was mainly justified by the need for a better understanding of the behavior of ALAN propagation into the environment in order to protect world-class astronomical facilities. More recently, alongside to the threat to the natural starry sky, many issues have emerged from the biological science community. It has been shown that, nearby or inside cities, the presence of cloud cover generally acts as an amplifier for artificial sky radiance while clouds behave as attenuators for remote observers. In this paper we show the spectral behavior of the zenith sky radiance amplification factor exerted by clouds inside a city. We compare in-situ measurements made with the spectrometer SAND-4 with a numerical model applied to the specific geographical context of the Universidad Complutense de Madrid in Spain.

  6. Cross Calibration of TOMS, SBUV/2 and Sciamachy Radiances from Ground Observations

    NASA Technical Reports Server (NTRS)

    Hillsenrath, Ernest; Ahmad, Ziauddin; Bhartia, Pawan K. (Technical Monitor)

    2001-01-01

    Verification of a stratospheric ozone recovery remains a high priority for environmental research and policy definition. Models predict an ozone recovery at a much lower rate than the measured depletion rate observed to date. Therefore improved precision of the satellite and ground ozone observing systems are required over the long term to verify recovery. We have shown that validation of radiances is the most effective means for correcting absolute accuracy and long term drifts of backscatter type satellite measurements. This method by-passes the algorithms used for both satellite and ground based measurements which are normally used to validate and correct the satellite data. Validation of radiances will also improve all higher level data products derived from the satellite observations. Backscatter algorithms suffer from several errors such as unrepresentative a-priori data and air mass factor corrections. Radiance comparisons employ forward models but are inherently more accurate and than inverse (retrieval) algorithms. A new method for satellite validation is planned which will compliment measurements from the existing ground-based networks. This method will employ very accurate comparisons between ground based zenith sky radiances and satellite nadir radiances. These comparisons will rely heavily on the experience derived from the Shuttle SBUV (SSBUV) program which provided a reference standard of radiance measurements for SBUV/2, TOMS, and GOME. This new measurement program, called "Skyrad", employs two well established capabilities at the Goddard Space Flight Center, 1) the SSBUV calibration facilities and 2) the radiative transfer codes used for the TOMS and SBUV/2 algorithms and their subsequent refinements. Radiative transfer calculations show that ground based zenith sky and satellite nadir backscatter ultraviolet comparisons can be made very accurately under certain viewing conditions. The Skyrad instruments (SSBUV, Brewer spectrophotometers, and

  7. The NBS scale of radiance temperature

    NASA Technical Reports Server (NTRS)

    Waters, William R.; Walker, James H.; Hattenburg, Albert T.

    1988-01-01

    The measurement methods and instrumentation used in the realization and transfer of the International Practical Temperature Scale (IPTS-68) above the temperature of freezing gold are described. The determination of the ratios of spectral radiance of tungsten-strip lamps to a gold-point blackbody at a wavelength of 654.6 nm is detailed. The response linearity, spectral responsivity, scattering error, and polarization properties of the instrumentation are described. The analysis of the sources of error and estimates of uncertainty are presented. The assigned uncertainties (three standard deviations) in radiance temperature range from + or - 2 K at 2573 K to + or - 0.5 K at 1073 K.

  8. Improving AIRS Radiance Spectra in High Contrast Scenes Using MODIS

    NASA Technical Reports Server (NTRS)

    Pagano, Thomas S.; Aumann, Hartmut H.; Manning, Evan M.; Elliott, Denis A.; Broberg, Steven E.

    2015-01-01

    The Atmospheric Infrared Sounder (AIRS) on the EOS Aqua Spacecraft was launched on May 4, 2002. AIRS acquires hyperspectral infrared radiances in 2378 channels ranging in wavelength from 3.7-15.4 microns with spectral resolution of better than 1200, and spatial resolution of 13.5 km with global daily coverage. The AIRS is designed to measure temperature and water vapor profiles for improvement in weather forecast accuracy and improved understanding of climate processes. As with most instruments, the AIRS Point Spread Functions (PSFs) are not the same for all detectors. When viewing a non-uniform scene, this causes a significant radiometric error in some channels that is scene dependent and cannot be removed without knowledge of the underlying scene. The magnitude of the error depends on the combination of non-uniformity of the AIRS spatial response for a given channel and the non-uniformity of the scene, but is typically only noticeable in about 1% of the scenes and about 10% of the channels. The current solution is to avoid those channels when performing geophysical retrievals. In this effort we use data from the Moderate Resolution Imaging Spectroradiometer (MODIS) instrument to provide information on the scene uniformity that is used to correct the AIRS data. For the vast majority of channels and footprints the technique works extremely well when compared to a Principal Component (PC) reconstruction of the AIRS channels. In some cases where the scene has high inhomogeneity in an irregular pattern, and in some channels, the method can actually degrade the spectrum. Most of the degraded channels appear to be slightly affected by random noise introduced in the process, but those with larger degradation may be affected by alignment errors in the AIRS relative to MODIS or uncertainties in the PSF. Despite these errors, the methodology shows the ability to correct AIRS radiances in non-uniform scenes under some of the worst case conditions and improves the ability to

  9. Computation of diffuse sky irradiance from multidirectional radiance measurements

    NASA Technical Reports Server (NTRS)

    Ahmad, Suraiya P.; Middleton, Elizabeth M.; Deering, Donald W.

    1987-01-01

    Accurate determination of the diffuse solar spectral irradiance directly above the land surface is important in characterizing the reflectance properties of these surfaces, especially vegetation canopies. This determination is also needed to infer the net radiation budget of the earth-atmosphere system above these surfaces. An algorithm is developed here for the computation of hemispheric diffuse irradiance using the measurements from an instrument called PARABOLA, which rapidly measures upwelling and downwelling radiances in three selected wavelength bands. The validity of the algorithm is established from simulations. The standard reference data set of diffuse radiances of Dave (1978), obtained by solving the radiative transfer equation numerically for realistic atmospheric models, is used to simulate PARABOLA radiances. Hemispheric diffuse irradiance is estimated from a subset of simulated radiances by using the algorithm described. The algorithm is validated by comparing the estimated diffuse irradiance with the true diffuse irradiance of the standard data set. The validations include sensitivity studies for two wavelength bands (visible, 0.65-0.67 micron; near infrared, 0.81-0.84 micron), different atmospheric conditions, solar elevations, and surface reflectances. In most cases the hemispheric diffuse irradiance computed from simulated PARABOLA radiances and the true irradiance obtained from radiative transfer calculations agree within 1-2 percent. This technique can be applied to other sampling instruments designed to estimate hemispheric diffuse sky irradiance.

  10. Theory of spectral radiance of pollutants at sea, volume 1

    NASA Technical Reports Server (NTRS)

    1979-01-01

    Remote measurement of pollutants dumped in the sea, not oil slicks, but soluble pollutants that change the color of the water, is addressed. The sensor is a spectral radiometer that flies over the polluted area and compares its spectral radiance (color) to that of surrounding clean seawater. The goal is to infer the concentration of pollutants using the measured radiance of the sea compared to laboratory measurements of reflection and transmission spectra of the pollutants. The subject is treated in three steps: (1) the quantities involved are defined and means for measuring them are described; (2) the equations for remote sensing with a low-flying aircraft are derived, in which wase the absorption and radiance of intervening air is negligible; and (3) high-flying aircraft and satellites are applied, in which case the radiance of intervening air is the major problem.

  11. Effects of Nighttime Light Radiance on the Sleep of the General Population

    NASA Technical Reports Server (NTRS)

    Ohayon, Maurice M.; Milesi, Cristina

    2015-01-01

    The objectives of this study is to verify if the exposure to greater nighttime radiance is associated with changes in the sleep/wake schedule and with greater sleep disturbances. Methods: The target population was the adults (18 years and older) living in California, USA. This represents 24 million of inhabitants. A total of 3,104 subjects participated in the survey (participation rate 85.6%). The participants were interviewed by telephone using the Sleep-EVAL system. The interviews covered several topics including sleeping habits, sleep quality, sleep disturbances, physical symptoms related to menopause. Chronic insomnia was defined as difficulty initiating or maintaining sleep for at least 3 months. Global nighttime light emissions have been collected by the Defense Meteorological Satellite Program's Operational Linescan System (DMSP/OLS) sensors. We extracted the radiance calibrated nighttime lights corresponding to the date of the interviews for a three by three window centered on each coordinate corresponding to an interview address. Results: Dissatisfaction with sleep quantity and/or quality was associated with an increased nighttime radiance (p=0.02). Similarly, excessive sleepiness accompanied with impaired functioning was significantly associated with an increased nighttime radiance (p (is) less than 0.0001). The association remained significant after controlling for age, gender and use of a night lamp in the bedroom. Confusional arousals were also significantly associated with an increased nighttime radiance (p (is) less than 0.0001). Bedtime hour was linearly increasing with the intensity of nighttime radiance: the later the bedtime, the greater the nighttime radiance (p (is) less than 0.0001). Similarly, wakeup time became progressively later as the nighttime radiance increased (p (is) less than 0.0001). Both associations remained significant after controlling for age, gender and use of a night lamp in the bedroom. Circadian Rhythm Disorders were the

  12. Scaling properties of observed and simulated satellite visible radiances

    NASA Astrophysics Data System (ADS)

    Barker, Howard W.; Qu, Zhipeng; Bélair, Stéphane; Leroyer, Sylvie; Milbrandt, Jason A.; Vaillancourt, Paul A.

    2017-09-01

    Structure functions Sq, which are related to power spectra and used to study turbulence, were computed for GOES-13 visible radiances measured on 16 May 2015 over French Guiana and adjacent Atlantic Ocean. The nested Global Environmental Multiscale (GEM) numerical weather prediction (NWP) model was run for the same time and area. Cloud data generated by GEM over (300 km)2 domains, with one-way nesting ending at horizontal grid-spacing of 0.25 km, were operated on by a 3-D solar radiative transfer model with resulting radiances degraded to GOES-13 resolution ( 1 km) and Sq computed for them, too. For GOES-13 radiances, scaling exponents ζ(2) associated with S2, for separation distances between 5 km and 25 km, were typically >0.6 for deep convective and marine boundary layer clouds and <0.4 for shallow cumuli over land. ζ(2) for GEM agreed well with GOES-13 for deep convective clouds. This suggests that the self-organizing properties of deep convection in GEM exhibit realistic geometric features, a potentially important point given the link between cloud structure and precipitation, with the latter being much more difficult to measure and assess than visible radiances. Regarding radiances for GEM's marine boundary layer clouds, their Sq differed markedly from GOES-13's; better resembling fair-weather cumulus. Likewise, GEM's shallow cumuli over land appear to have bypassed the "scattered" fair-weather stage and went straight into more organized convection. Thus, it appears that comparing time series of Sq for geostationary satellite data and corresponding modeled radiances has the potential to benefit assessment of cloud system-resolving models.

  13. Spectral radiance source based on supercontinuum laser and wavelength tunable bandpass filter: the spectrally tunable absolute irradiance and radiance source.

    PubMed

    Levick, Andrew P; Greenwell, Claire L; Ireland, Jane; Woolliams, Emma R; Goodman, Teresa M; Bialek, Agnieszka; Fox, Nigel P

    2014-06-01

    A new spectrally tunable source for calibration of radiometric detectors in radiance, irradiance, or power mode has been developed and characterized. It is termed the spectrally tunable absolute irradiance and radiance source (STAIRS). It consists of a supercontinuum laser, wavelength tunable bandpass filter, power stabilization feedback control scheme, and output coupling optics. It has the advantages of relative portability and a collimated beam (low étendue), and is an alternative to conventional sources such as tungsten lamps, blackbodies, or tunable lasers. The supercontinuum laser is a commercial Fianium SC400-6-02, which has a wavelength range between 400 and 2500 nm and a total power of 6 W. The wavelength tunable bandpass filter, a PhotonEtc laser line tunable filter (LLTF), is tunable between 400 and 1000 nm and has a bandwidth of 1 or 2 nm depending on the wavelength selected. The collimated laser beam from the LLTF filter is converted to an appropriate spatial and angular distribution for the application considered (i.e., for radiance, irradiance, or power mode calibration of a radiometric sensor) with the output coupling optics, for example, an integrating sphere, and the spectral radiance/irradiance/power of the source is measured using a calibration optical sensor. A power stabilization feedback control scheme has been incorporated that stabilizes the source to better than 0.01% for averaging times longer than 100 s. The out-of-band transmission of the LLTF filter is estimated to be < -65 dB (0.00003%), and is sufficiently low for many end-user applications, for example the spectral radiance calibration of earth observation imaging radiometers and the stray light characterization of array spectrometers (the end-user optical sensor). We have made initial measurements of two end-user instruments with the STAIRS source, an array spectrometer and ocean color radiometer.

  14. Calibration of TOMS Radiances From Ground Observations

    NASA Technical Reports Server (NTRS)

    Bojkov, B. R.; Kowalewski, M.; Wellemeyer, C.; Labow, G.; Hilsenrath, E.; Bhartia, P. K.; Ahmad, Z.

    2003-01-01

    Verification of a stratospheric ozone recovery remains a high priority for environmental research and policy definition. Models predict an ozone recovery at a much lower rate than the measured depletion rate observed to date. Therefore improved precision of the satellite and ground ozone observing systems are required over the long term to verify its recovery. We show that validation of radiances from the ground can be a very effective means for correcting long term drifts of backscatter type satellite measurements and can be used to cross calibrate all BUV instruments in orbit (TOMS, SBUV/2, GOME, SCIAMACHY, OMI, GOME-2, OMPS). This method bypasses the retrieval algorithms used to derive ozone products from both satellite and ground based measurements that are normally used to validate the satellite data. Radiance comparisons employ forward models, but they are inherently more accurate than the retrieval This method employs very accurate comparisons between ground based zenith sicy radiances and satellite nadir radiances and employs two well established capabilities at the Goddard Space Flight Center, 1) the SSBUV calibration facilities and 2) the radiative transfer codes used for the TOMS and SBUV/2 algorithms and their subsequent refinements. The zenith sky observations are made by the SSBUV where its calibration is maintained to a high degree of accuracy and precision. Radiative transfer calculations show that ground based zenith sky and satellite nadir backscatter ultraviolet comparisons can be made very accurately under certain viewing conditions. Initial ground observations taken from Goddard Space Flight Center compared with radiative transfer calculations has indicated the feasibility of this method. The effect of aerosols and varying ozone amounts are considered in the model simulations and the theoretical comparisons. The radiative transfer simulations show that the ground and satellite radiance comparisons can be made with an uncertainty of less than l

  15. Sensitivity analysis of upwelling thermal radiance in presence of clouds

    NASA Technical Reports Server (NTRS)

    Subramanian, S. V.; Tiwari, S. N.; Suttles, J. T.

    1981-01-01

    Total upwelling radiance at the top of the atmosphere is evaluated theoretically in the presence of clouds. The influence of cloud heights, thicknesses and different cloud covers on the upwelling radiance is also investigated. The characteristics of the two cloud types considered in this study closely correspond to altocumulus and cirrus with the cloud emissivity as a function of its liquid water (or ice) content. For calculation of the integrated transmittance of atmospheric gases such as, H2O, CO2, O3, and N2O, the Quasi Random Band (QRB) model approach is adopted. Results are obtained in three different spectral ranges and are compared with the clearsky radiance results. It is found that the difference between the clearsky and cloudy radiance increases with increasing cloud height and liquid water content. This difference also decreases as the surface temperature approaches the value of the cloud top temperature.

  16. Community Radiative Transfer Model for Satellite Radiance Simulation

    NASA Astrophysics Data System (ADS)

    Liu, Q.; Han, Y.; Chen, Y.; van Delst, P.; Weng, F.

    2007-12-01

    The Community Radiative Transfer Model (CRTM) [Weng et al., 2005], developed at U.S. Joint Center for Satellite Data Assimilation (JCSDA), has been used for the satellite radiance simulation and the radiance derivatives to the surface/atmospheric parameters in the physical retrieval [Boukabara et al., 2007], data assimilation [Le Marshall et al., 2006] and many others [Han et al., 2006; Liu and Weng, 2006]. CRTM has been become a key component in U.S. data assimilation at the National Center for Environmental Prediction (NCEP) [Okamoto and. Derber, 2006]. It is a core engine for NOAA/NESDIS Microwave Integrated Retrieval System (MIRS) [Boukabara et al., 2007]. The CRTM has also been implemented into Weather Research Forecasting (WRF) model. The CRTM is known as modular program development [van Delst et al., 2006], which breaks down the radiative transfer model into components, each of which is encapsulated in one or several program modules and can be developed independently of the others. The key components of the CRTM are the advanced surface emissivity and reflectivity models [van Delst and Wu, 2000; English 1999; Weng et al. 2001] including a polarimetric surface emissivity model [Liu and Weng, 2003], the fast Optical Path Transmittance (OPTRAN) model [Xiong et al., 2006], the cloud absorption/scattering look-up tables [Yang et al., 2000], and the advanced radiative solver [Liu and Weng, 2006]. The CRTM can also compute aerosol radiance. The CRTM can deal with Zeeman splitting effect, the energy received in the channels for the stratosphere and mesosphere depends strongly on the geomagnetic field and its orientation with respect to the direction of observation [Han et al., 2007]. We will also present the applications of the CRTM in hurricane detection and forecasting, in the determination of stratospheric temperature, a key contributing factor to photochemical ozone depletion, and in reanalysis and climate studies.

  17. Examining Dense Data Usage near the Regions with Severe Storms in All-Sky Microwave Radiance Data Assimilation and Impacts on GEOS Hurricane Analyses

    NASA Technical Reports Server (NTRS)

    Kim, Min-Jeong; Jin, Jianjun; McCarty, Will; El Akkraoui, Amal; Todling, Ricardo; Gelaro, Ron

    2018-01-01

    Many numerical weather prediction (NWP) centers assimilate radiances affected by clouds and precipitation from microwave sensors, with the expectation that these data can provide critical constraints on meteorological parameters in dynamically sensitive regions to make significant impacts on forecast accuracy for precipitation. The Global Modeling and Assimilation Office (GMAO) at NASA Goddard Space Flight Center assimilates all-sky microwave radiance data from various microwave sensors such as all-sky GPM Microwave Imager (GMI) radiance in the Goddard Earth Observing System (GEOS) atmospheric data assimilation system (ADAS), which includes the GEOS atmospheric model, the Gridpoint Statistical Interpolation (GSI) atmospheric analysis system, and the Goddard Aerosol Assimilation System (GAAS). So far, most of NWP centers apply same large data thinning distances, that are used in clear-sky radiance data to avoid correlated observation errors, to all-sky microwave radiance data. For example, NASA GMAO is applying 145 km thinning distances for most of satellite radiance data including microwave radiance data in which all-sky approach is implemented. Even with these coarse observation data usage in all-sky assimilation approach, noticeable positive impacts from all-sky microwave data on hurricane track forecasts were identified in GEOS-5 system. The motivation of this study is based on the dynamic thinning distance method developed in our all-sky framework to use of denser data in cloudy and precipitating regions due to relatively small spatial correlations of observation errors. To investigate the benefits of all-sky microwave radiance on hurricane forecasts, several hurricane cases selected between 2016-2017 are examined. The dynamic thinning distance method is utilized in our all-sky approach to understand the sources and mechanisms to explain the benefits of all-sky microwave radiance data from various microwave radiance sensors like Advanced Microwave Sounder Unit

  18. Determination of Unfiltered Radiances from the Clouds and the Earth's Radiant Energy System (CERES) Instrument

    NASA Technical Reports Server (NTRS)

    Loeb, N. G.; Priestley, K. J.; Kratz, D. P.; Geier, E. B.; Green, R. N.; Wielicki, B. A.; Hinton, P. OR.; Nolan, S. K.

    2001-01-01

    A new method for determining unfiltered shortwave (SW), longwave (LW) and window (W) radiances from filtered radiances measured by the Clouds and the Earth's Radiant Energy System (CERES) satellite instrument is presented. The method uses theoretically derived regression coefficients between filtered and unfiltered radiances that are a function of viewing geometry, geotype and whether or not cloud is present. Relative errors in insta.ntaneous unfiltered radiances from this method are generally well below 1% for SW radiances (approx. 0.4% 1(sigma) or approx.l W/sq m equivalent flux), < 0.2% for LW radiances (approx. 0.1% 1(sigma) or approx.0.3 W/sq m equivalent flux) and < 0.2% (approx. 0.1% 1(sigma) for window channel radiances.

  19. Spectral Dimensionality and Scale of Urban Radiance

    NASA Technical Reports Server (NTRS)

    Small, Christopher

    2001-01-01

    Characterization of urban radiance and reflectance is important for understanding the effects of solar energy flux on the urban environment as well as for satellite mapping of urban settlement patterns. Spectral mixture analyses of Landsat and Ikonos imagery suggest that the urban radiance field can very often be described with combinations of three or four spectral endmembers. Dimensionality estimates of Airborne Visible/Infrared Imaging Spectrometer (AVIRIS) radiance measurements of urban areas reveal the existence of 30 to 60 spectral dimensions. The extent to which broadband imagery collected by operational satellites can represent the higher dimensional mixing space is a function of both the spatial and spectral resolution of the sensor. AVIRIS imagery offers the spatial and spectral resolution necessary to investigate the scale dependence of the spectral dimensionality. Dimensionality estimates derived from Minimum Noise Fraction (MNF) eigenvalue distributions show a distinct scale dependence for AVIRIS radiance measurements of Milpitas, California. Apparent dimensionality diminishes from almost 40 to less than 10 spectral dimensions between scales of 8000 m and 300 m. The 10 to 30 m scale of most features in urban mosaics results in substantial spectral mixing at the 20 m scale of high altitude AVIRIS pixels. Much of the variance at pixel scales is therefore likely to result from actual differences in surface reflectance at pixel scales. Spatial smoothing and spectral subsampling of AVIRIS spectra both result in substantial loss of information and reduction of apparent dimensionality, but the primary spectral endmembers in all cases are analogous to those found in global analyses of Landsat and Ikonos imagery of other urban areas.

  20. Evaluation of upwelling infrared radiance from earth's atmosphere

    NASA Technical Reports Server (NTRS)

    Gupta, S. K.; Tiwari, S. N.

    1975-01-01

    Basic equations for calculating the upwelling atmospheric radiation are presented which account for various sources of radiation coming out at the top of the atmosphere. The theoretical formulation of the transmittance models (line-by-line and quasi-random band model) and the computational procedures used for the evaluation of the transmittance and radiance are discussed in detail. By employing the Lorentz line-by-line and quasi-random computer programs, model calculations were made to determine the upwelling radiance and signal change in the wave number interval of CO fundamental band. These results are useful in determining the effects of different interfering molecules, water vapor profiles, ground temperatures, and ground emittances on the upwelling radiance and signal change. This information is of vital importance in establishing the feasibility of measuring the concentrations of pollutants in the atmosphere from a gas filter correlation instrument flown on an aircraft or mounted on a satellite.

  1. Implementation and application of an interactive user-friendly validation software for RADIANCE

    NASA Astrophysics Data System (ADS)

    Sundaram, Anand; Boonn, William W.; Kim, Woojin; Cook, Tessa S.

    2012-02-01

    RADIANCE extracts CT dose parameters from dose sheets using optical character recognition and stores the data in a relational database. To facilitate validation of RADIANCE's performance, a simple user interface was initially implemented and about 300 records were evaluated. Here, we extend this interface to achieve a wider variety of functions and perform a larger-scale validation. The validator uses some data from the RADIANCE database to prepopulate quality-testing fields, such as correspondence between calculated and reported total dose-length product. The interface also displays relevant parameters from the DICOM headers. A total of 5,098 dose sheets were used to test the performance accuracy of RADIANCE in dose data extraction. Several search criteria were implemented. All records were searchable by accession number, study date, or dose parameters beyond chosen thresholds. Validated records were searchable according to additional criteria from validation inputs. An error rate of 0.303% was demonstrated in the validation. Dose monitoring is increasingly important and RADIANCE provides an open-source solution with a high level of accuracy. The RADIANCE validator has been updated to enable users to test the integrity of their installation and verify that their dose monitoring is accurate and effective.

  2. Sky radiance at a coastline and effects of land and ocean reflectivities

    NASA Astrophysics Data System (ADS)

    Kreuter, Axel; Blumthaler, Mario; Tiefengraber, Martin; Kift, Richard; Webb, Ann R.

    2017-12-01

    We present a unique case study of the spectral sky radiance distribution above a coastline. Results are shown from a measurement campaign in Italy involving three diode array spectroradiometers which are compared to 3-D model simulations from the Monte Carlo model MYSTIC. On the coast, the surrounding is split into two regions, a diffusely reflecting land surface and a water surface which features a highly anisotropic reflectance function. The reflectivities and hence the resulting radiances are a nontrivial function of solar zenith and azimuth angle and wavelength. We show that for low solar zenith angles (SZAs) around noon, the higher land albedo causes the sky radiance at 20° above the horizon to increase by 50 % in the near infrared at 850 nm for viewing directions towards the land with respect to the ocean. Comparing morning and afternoon radiances highlights the effect of the ocean's sun glint at high SZA, which contributes around 10 % to the measured radiance ratios. The model simulations generally agree with the measurements to better than 10 %. We investigate the individual effects of model input parameters representing land and ocean albedo and aerosols. Different land and ocean bi-directional reflectance functions (BRDFs) do not generally improve the model agreement. However, consideration of the uncertainties in the diurnal variation of aerosol optical depth can explain the remaining discrepancies between measurements and model. We further investigate the anisotropy effect of the ocean BRDF which is featured in the zenith radiances. Again, the uncertainty of the aerosol loading is dominant and obscures the modelled sun glint effect of 7 % at 650 nm. Finally, we show that the effect on the zenith radiance is restricted to a few kilometres from the coastline by model simulations along a perpendicular transect and by comparing the radiances at the coast to those measured at a site 15 km inland. Our findings are relevant to, for example, ground

  3. Satellite radiance data assimilation for binary tropical cyclone cases over the western North Pacific

    NASA Astrophysics Data System (ADS)

    Choi, Yonghan; Cha, Dong-Hyun; Lee, Myong-In; Kim, Joowan; Jin, Chun-Sil; Park, Sang-Hun; Joh, Min-Su

    2017-06-01

    A total of three binary tropical cyclone (TC) cases over the Western North Pacific are selected to investigate the effects of satellite radiance data assimilation on analyses and forecasts of binary TCs. Two parallel cycling experiments with a 6 h interval are performed for each binary TC case, and the difference between the two experiments is whether satellite radiance observations are assimilated. Satellite radiance observations are assimilated using the Weather Research and Forecasting Data Assimilation (WRFDA)'s three-dimensional variational (3D-Var) system, which includes the observation operator, quality control procedures, and bias correction algorithm for radiance observations. On average, radiance assimilation results in slight improvements of environmental fields and track forecasts of binary TC cases, but the detailed effects vary with the case. When there is no direct interaction between binary TCs, radiance assimilation leads to better depictions of environmental fields, and finally it results in improved track forecasts. However, positive effects of radiance assimilation on track forecasts can be reduced when there exists a direct interaction between binary TCs and intensities/structures of binary TCs are not represented well. An initialization method (e.g., dynamic initialization) combined with radiance assimilation and/or more advanced DA techniques (e.g., hybrid method) can be considered to overcome these limitations.

  4. Effects of Raman scattering on the water-leaving radiance

    NASA Technical Reports Server (NTRS)

    Waters, Kirk J.

    1995-01-01

    The contribution of Raman scattering to the water-leaving radiance is examined using Monte Carlo simulations. Exit angle information is retained, allowing a comparison of different satellite viewing directions. Chlorophyll values of 0.0, 0.01, 0.1, and 1.0 mg Chl/cu m are simulated. Little directional variability is found, with the exception of the direct solar backscatter direction. The wavelength variability is greatest for low chlorophyll concentrations and is negligible for 1.0 mg Chl/cu m. At 550 nm the Raman contribution ranges from approximately 18% of the total water-leaving radiance for pure water to 3% for 1.0 mg Chl/cu m. At 440 nm the range is from 6% to 2%, indicating that Raman scattering will impact radiance ratios for ocean color satellite algorithms.

  5. Determination of immersion factors for radiance sensors in marine and inland waters: a semi-analytical approach using refractive index approximation

    NASA Astrophysics Data System (ADS)

    Dev, Pravin J.; Shanmugam, P.

    2016-05-01

    Underwater radiometers are generally calibrated in air using a standard source. The immersion factors are required for these radiometers to account for the change in the in-water measurements with respect to in-air due to the different refractive index of the medium. The immersion factors previously determined for RAMSES series of commercial radiometers manufactured by TriOS are applicable to clear oceanic waters. In typical inland and turbid productive coastal waters, these experimentally determined immersion factors yield significantly large errors in water-leaving radiances (Lw) and hence remote sensing reflectances (Rrs). To overcome this limitation, a semi-analytical method with based on the refractive index approximation is proposed in this study, with the aim of obtaining reliable Lw and Rrs from RAMSES radiometers for turbid and productive waters within coastal and inland water environments. We also briefly show the variation of pure water immersion factors (Ifw) and newly derived If on Lw and Rrs for clear and turbid waters. The remnant problems other than the immersion factor coefficients such as transmission, air-water and water-air Fresnel's reflectances are also discussed.

  6. Sky-radiance gradient measurements at narrow bands in the visible.

    PubMed

    Winter, E M; Metcalf, T W; Stotts, L B

    1995-07-01

    Accurate calibrated measurements of the radiance of the daytime sky were made in narrow bands in the visible portion of the spectrum. These measurements were made over several months and were tabulated in a sun-referenced coordinate system. The radiance as a function of wavelength at angles ranging from 5 to 90 deg was plotted. A best-fit inverse power-law fit shows inversely linear behavior of the radiance versus wavelength near the Sun (5 deg) and a slope approaching inverse fourth power far from the Sun (60 deg). This behavior fits a Mie-scattering interpretation near the Sun and a Rayleigh-scattering interpretation away from the Sun. The results are also compared with LOWTRAN models.

  7. RADIANCE AND PHOTON NOISE: Imaging in geometrical optics, physical optics, quantum optics and radiology.

    PubMed

    Barrett, Harrison H; Myers, Kyle J; Caucci, Luca

    2014-08-17

    A fundamental way of describing a photon-limited imaging system is in terms of a Poisson random process in spatial, angular and wavelength variables. The mean of this random process is the spectral radiance. The principle of conservation of radiance then allows a full characterization of the noise in the image (conditional on viewing a specified object). To elucidate these connections, we first review the definitions and basic properties of radiance as defined in terms of geometrical optics, radiology, physical optics and quantum optics. The propagation and conservation laws for radiance in each of these domains are reviewed. Then we distinguish four categories of imaging detectors that all respond in some way to the incident radiance, including the new category of photon-processing detectors. The relation between the radiance and the statistical properties of the detector output is discussed and related to task-based measures of image quality and the information content of a single detected photon.

  8. RADIANCE AND PHOTON NOISE: Imaging in geometrical optics, physical optics, quantum optics and radiology

    PubMed Central

    Barrett, Harrison H.; Myers, Kyle J.; Caucci, Luca

    2016-01-01

    A fundamental way of describing a photon-limited imaging system is in terms of a Poisson random process in spatial, angular and wavelength variables. The mean of this random process is the spectral radiance. The principle of conservation of radiance then allows a full characterization of the noise in the image (conditional on viewing a specified object). To elucidate these connections, we first review the definitions and basic properties of radiance as defined in terms of geometrical optics, radiology, physical optics and quantum optics. The propagation and conservation laws for radiance in each of these domains are reviewed. Then we distinguish four categories of imaging detectors that all respond in some way to the incident radiance, including the new category of photon-processing detectors. The relation between the radiance and the statistical properties of the detector output is discussed and related to task-based measures of image quality and the information content of a single detected photon. PMID:27478293

  9. Effect of Aerosol Variation on Radiance in the Earth's Atmosphere-Ocean System.

    PubMed

    Plass, G N; Kattawar, G W

    1972-07-01

    The reflected and transmitted radiance is calculated for a realistic model of the atmosphere-ocean system. Multiple scattering to all orders as well as anisotropic scattering from aerosols are taken into account by a Monte Carlo technique. The probability for reflection or refraction at the ocean surface is calculated for each photon. Scattering and absorption by water molecules (Rayleigh) and by hydrosols (Mie) are taken into account within the ocean. The radiance is calculated for a normal aerosol distribution as well as for a three and ten times normal distribution. Calculations are also made for an aerosol layer near the earth as well as for one in the stratosphere. The upward radiance at the top of the atmosphere depends strongly on the total number of aerosols but not on their spatial distribution. Variations in the ozone amount also have little effect on the upward radiance. The calculations are made at the following wavelengths: 0.7 micro, 0.9 micro, 1.67 micro. The radiance above and below the ocean surface as well as the flux at various levels are also discussed.

  10. IASI Radiance Data Assimilation in Local Ensemble Transform Kalman Filter

    NASA Astrophysics Data System (ADS)

    Cho, K.; Hyoung-Wook, C.; Jo, Y.

    2016-12-01

    Korea institute of Atmospheric Prediction Systems (KIAPS) is developing NWP model with data assimilation systems. Local Ensemble Transform Kalman Filter (LETKF) system, one of the data assimilation systems, has been developed for KIAPS Integrated Model (KIM) based on cubed-sphere grid and has successfully assimilated real data. LETKF data assimilation system has been extended to 4D- LETKF which considers time-evolving error covariance within assimilation window and IASI radiance data assimilation using KPOP (KIAPS package for observation processing) with RTTOV (Radiative Transfer for TOVS). The LETKF system is implementing semi operational prediction including conventional (sonde, aircraft) observation and AMSU-A (Advanced Microwave Sounding Unit-A) radiance data from April. Recently, the semi operational prediction system updated radiance observations including GPS-RO, AMV, IASI (Infrared Atmospheric Sounding Interferometer) data at July. A set of simulation of KIM with ne30np4 and 50 vertical levels (of top 0.3hPa) were carried out for short range forecast (10days) within semi operation prediction LETKF system with ensemble forecast 50 members. In order to only IASI impact, our experiments used only conventional and IAIS radiance data to same semi operational prediction set. We carried out sensitivity test for IAIS thinning method (3D and 4D). IASI observation number was increased by temporal (4D) thinning and the improvement of IASI radiance data impact on the forecast skill of model will expect.

  11. Calculation of the angular radiance distribution for a coupled atmosphere and canopy

    NASA Technical Reports Server (NTRS)

    Liang, Shunlin; Strahler, Alan H.

    1993-01-01

    The radiative transfer equations for a coupled atmosphere and canopy are solved numerically by an improved Gauss-Seidel iteration algorithm. The radiation field is decomposed into three components: unscattered sunlight, single scattering, and multiple scattering radiance for which the corresponding equations and boundary conditions are set up and their analytical or iterational solutions are explicitly derived. The classic Gauss-Seidel algorithm has been widely applied in atmospheric research. This is its first application for calculating the multiple scattering radiance of a coupled atmosphere and canopy. This algorithm enables us to obtain the internal radiation field as well as radiances at boundaries. Any form of bidirectional reflectance distribution function (BRDF) as a boundary condition can be easily incorporated into the iteration procedure. The hotspot effect of the canopy is accommodated by means of the modification of the extinction coefficients of upward single scattering radiation and unscattered sunlight using the formulation of Nilson and Kuusk. To reduce the computation for the case of large optical thickness, an improved iteration formula is derived to speed convergence. The upwelling radiances have been evaluated for different atmospheric conditions, leaf area index (LAI), leaf angle distribution (LAD), leaf size and so on. The formulation presented in this paper is also well suited to analyze the relative magnitude of multiple scattering radiance and single scattering radiance in both the visible and near infrared regions.

  12. Vacuum Radiance-Temperature Standard Facility for Infrared Remote Sensing at NIM

    NASA Astrophysics Data System (ADS)

    Hao, X. P.; Song, J.; Xu, M.; Sun, J. P.; Gong, L. Y.; Yuan, Z. D.; Lu, X. F.

    2018-06-01

    As infrared remote sensors are very important parts of Earth observation satellites, they must be calibrated based on the radiance temperature of a blackbody in a vacuum chamber prior to launch. The uncertainty of such temperature is thus an essential component of the sensors' uncertainty. This paper describes the vacuum radiance-temperature standard facility (VRTSF) at the National Institute of Metrology of China, which will serve to calibrate infrared remote sensors on Chinese meteorological satellites. The VRTSF can be used to calibrate vacuum blackbody radiance temperature, including those used to calibrate infrared remote sensors. The components of the VRTSF are described in this paper, including the VMTBB, the LNBB, the FTIR spectrometer, the reduced-background optical system, the vacuum chamber used to calibrate customers' blackbody, the vacuum-pumping system and the liquid-nitrogen-support system. The experimental methods and results are expounded. The uncertainty of the radiance temperature of VMTBB is 0.026 °C at 30 °C over 10 μm.

  13. One Moon, many measurements 1: Radiance values

    NASA Astrophysics Data System (ADS)

    Pieters, C. M.; Boardman, J. W.; Ohtake, M.; Matsunaga, T.; Haruyama, J.; Green, R. O.; Mall, U.; Staid, M. I.; Isaacson, P. J.; Yokota, Y.; Yamamoto, S.; Besse, S.; Sunshine, J. M.

    2013-09-01

    Several modern optical instruments orbited the Moon during 2008 and 2009 onboard the SELENE and Chandrayaan-1 spacecraft and provided a welcomed feast of spectroscopic data to be used for scientific analyses. The different spatial and spectral resolutions of these sensors along with diverse illumination geometry during data acquisition make each set of data unique, and each instrument contributes special value to integrated science analyses. In order to provide the maximum science benefit, we have undertaken a careful cross-validation of radiance data among these orbital instruments and also a set of systematic data acquired using Earth-based telescopes. Most radiance values at 750 nm fall between 0 and 100 W/(m2 μm sr), but a small important fraction can be up to ×2 to ×3 that value, with the largest values occurring at the highest spatial resolution. All instruments are in agreement about overall spectral properties of lunar materials, but small systematic differences are documented between instruments. Lunar radiance values measured with remote sensors for landing sites are all not as high as that estimated from laboratory measurements of returned soil. This is largely because laboratory measurements of lunar soils cannot retain or duplicate the fine structure of lunar regolith found in the natural space environment.

  14. Surface Emissivity Effects on Thermodynamic Retrieval of IR Spectral Radiance

    NASA Technical Reports Server (NTRS)

    Zhou, Daniel K.; Larar, Allen M.; Smith, William L.; Liu, Xu

    2006-01-01

    The surface emissivity effect on the thermodynamic parameters (e.g., the surface skin temperature, atmospheric temperature, and moisture) retrieved from satellite infrared (IR) spectral radiance is studied. Simulation analysis demonstrates that surface emissivity plays an important role in retrieval of surface skin temperature and terrestrial boundary layer (TBL) moisture. NAST-I ultraspectral data collected during the CLAMS field campaign are used to retrieve thermodynamic properties of the atmosphere and surface. The retrievals are then validated by coincident in-situ measurements, such as sea surface temperature, radiosonde temperature and moisture profiles. Retrieved surface emissivity is also validated by that computed from the observed radiance and calculated emissions based on the retrievals of surface temperature and atmospheric profiles. In addition, retrieved surface skin temperature and emissivity are validated together by radiance comparison between the observation and retrieval-based calculation in the window region where atmospheric contribution is minimized. Both simulation and validation results have lead to the conclusion that variable surface emissivity in the inversion process is needed to obtain accurate retrievals from satellite IR spectral radiance measurements. Retrieval examples are presented to reveal that surface emissivity plays a significant role in retrieving accurate surface skin temperature and TBL thermodynamic parameters.

  15. CIMEL Measurements of Zenith Radiances at the ARM Site

    NASA Technical Reports Server (NTRS)

    Marshak, Alexander; Wiscombe, Warren; Lau, William K. M. (Technical Monitor)

    2002-01-01

    Starting from October 1, 2001, Cimel at the ARM Central Facility in Oklahoma has been switched to a new "cloud mode." This mode allows taking measurements of zenith radiance when the Sun in blocked by clouds. In this case, every 13 min. Cimel points straight up and takes 10 measurements with 9 sec. time interval. The new Cimel's mode has four filters at 440, 670, 870 and 1020 nm. For cloudy conditions, the spectral contrast in surface albedo dominates over Rayleigh and aerosol effects; this makes normalized zenith radiances at 440 and 670 as well as for 870 and 1020 almost indistinguishable. We compare Cimel measurements with other ARM cart site instruments: Multi-Filter Rotating Shadowband Radiometer (MFRSR), Narrow Field of View (NFOV) sensor, and MicroWave Radiometer(MWR). Based on Cimel and MFRSR 670 and 870 nm channels, we build a normalized difference cloud index (NDCI) for radiances and fluxes, respectively. Radiance NDCI from Cimel and flux NDCI from MFRSR are compared between themselves as well as with cloud Liquid Water Path (LWP) retrieved from MWR. Based on our theoretical calculations and preliminary data analysis,there is a good correlation between NDCIs and LWP for cloudy sky above green vegetation. Based on this correlation, an algorithm to retrieve cloud optical depth from NDCI is proposed.

  16. Physical Mechanism, Spectral Detection, and Potential Mitigation of 3D Cloud Effects on OCO-2 Radiances and Retrievals

    NASA Astrophysics Data System (ADS)

    Cochrane, S.; Schmidt, S.; Massie, S. T.; Iwabuchi, H.; Chen, H.

    2017-12-01

    Analysis of multiple partially cloudy scenes as observed by OCO-2 in nadir and target mode (published previously and reviewed here) revealed that XCO2 retrievals are systematically biased in presence of scattered clouds. The bias can only partially be removed by applying more stringent filtering, and it depends on the degree of scene inhomogeneity as quantified with collocated MODIS/Aqua imagery. The physical reason behind this effect was so far not well understood because in contrast to cloud-mediated biases in imagery-derived aerosol retrievals, passive gas absorption spectroscopy products do not depend on the absolute radiance level and should therefore be less sensitive to 3D cloud effects and surface albedo variability. However, preliminary evidence from 3D radiative transfer calculations suggested that clouds in the vicinity of an OCO-2 footprint not only offset the reflected radiance spectrum, but introduce a spectrally dependent perturbation that affects absorbing channels disproportionately, and therefore bias the spectroscopy products. To understand the nature of this effect for a variety of scenes, we developed the OCO-2 radiance simulator, which uses the available information on a scene (e.g., MODIS-derived surface albedo, cloud distribution, and other parameters) as the basis for 3D radiative transfer calculations that can predict the radiances observed by OCO-2. We present this new tool and show examples of its utility for a few specific scenes. More importantly, we draw conclusions about the physical mechanism behind this 3D cloud effect on radiances and ultimately OCO-2 retrievals, which involves not only the clouds themselves but also the surface. Harnessed with this understanding, we can now detect cloud vicinity effects in the OCO-2 spectra directly, without actually running the 3D radiance simulator. Potentially, it is even possible to mitigate these effects and thus increase data harvest in regions with ubiquitous cloud cover such as the Amazon

  17. Effect of aerosol variation on radiance in the earth's atmosphere-ocean system.

    NASA Technical Reports Server (NTRS)

    Plass, G. N.; Kattawar, G. W.

    1972-01-01

    Calculation of the radiance at the top and bottom of the atmosphere with a realistic model of both the atmosphere and ocean. It is found that the upward flux at the top of the atmosphere, as well as the angular distribution of the radiation, changes appreciably as the aerosol amount increases from normal to ten times normal. At the same time, the upward and downward radiance just above the ocean surface undergoes important changes. The radiance does not change appreciably with variations in the aerosol distribution with height so long as the total aerosol amount remains constant. Similarly, changes in the ozone amount cause only small changes in the radiance at the wavelengths considered (0.7, 0.9, and 1.67 micron). Very little radiation returns to the atmosphere from the ocean at 0.9 and 1.67 micron because of the high absorption of water at these wavelengths.

  18. The Impact of Cross-track Infrared Sounder (CrIS) Cloud-Cleared Radiances on Hurricane Joaquin (2015) and Matthew (2016) Forecasts

    NASA Astrophysics Data System (ADS)

    Wang, Pei; Li, Jun; Li, Zhenglong; Lim, Agnes H. N.; Li, Jinlong; Schmit, Timothy J.; Goldberg, Mitchell D.

    2017-12-01

    Hyperspectral infrared (IR) sounders provide high vertical resolution atmospheric sounding information that can improve the forecast skill in numerical weather prediction. Commonly, only clear radiances are assimilated, because IR sounder observations are highly affected by clouds. A cloud-clearing (CC) technique, which removes the cloud effects from an IR cloudy field of view (FOV) and derives the cloud-cleared radiances (CCRs) or clear-sky equivalent radiances, can be an alternative yet effective way to take advantage of the thermodynamic information from cloudy skies in data assimilation. This study develops a Visible Infrared Imaging Radiometer Suite (VIIRS)-based CC method for deriving Cross-track Infrared Sounder (CrIS) CCRs under partially cloudy conditions. Due to the lack of absorption bands on VIIRS, two important quality control steps are implemented in the CC process. Validation using VIIRS clear radiances indicates that the CC method can effectively obtain the CrIS CCRs for FOVs with partial cloud cover. To compare the impacts from assimilation of CrIS original radiances and CCRs, three experiments are carried out on two storm cases, Hurricane Joaquin (2015) and Hurricane Matthew (2016), using Gridpoint Statistical Interpolation assimilation system and Weather Research and Forecasting-Advanced Research Version models. At the analysis time, more CrIS observations are assimilated when using CrIS CCRs than with CrIS original radiances. Comparing temperature, specific humidity, and U/V winds with radiosondes indicates that the data impacts are growing larger with longer time forecasts (beyond 72 h forecast). Hurricane track forecasts also show improvements from the assimilation of CrIS CCRs due to better weather system forecasts. The impacts of CCRs on intensity are basically neutral with mixed positive and negative results.

  19. Estimation of spectral distribution of sky radiance using a commercial digital camera.

    PubMed

    Saito, Masanori; Iwabuchi, Hironobu; Murata, Isao

    2016-01-10

    Methods for estimating spectral distribution of sky radiance from images captured by a digital camera and for accurately estimating spectral responses of the camera are proposed. Spectral distribution of sky radiance is represented as a polynomial of the wavelength, with coefficients obtained from digital RGB counts by linear transformation. The spectral distribution of radiance as measured is consistent with that obtained by spectrometer and radiative transfer simulation for wavelengths of 430-680 nm, with standard deviation below 1%. Preliminary applications suggest this method is useful for detecting clouds and studying the relation between irradiance at the ground and cloud distribution.

  20. High-radiance LDP source for mask inspection and beam line applications (Conference Presentation)

    NASA Astrophysics Data System (ADS)

    Teramoto, Yusuke; Santos, Bárbara; Mertens, Guido; Kops, Ralf; Kops, Margarete; von Wezyk, Alexander; Bergmann, Klaus; Yabuta, Hironobu; Nagano, Akihisa; Ashizawa, Noritaka; Taniguchi, Yuta; Yamatani, Daiki; Shirai, Takahiro; Kasama, Kunihiko

    2017-04-01

    High-throughput actinic mask inspection tools are needed as EUVL begins to enter into volume production phase. One of the key technologies to realize such inspection tools is a high-radiance EUV source of which radiance is supposed to be as high as 100 W/mm2/sr. Ushio is developing laser-assisted discharge-produced plasma (LDP) sources. Ushio's LDP source is able to provide sufficient radiance as well as cleanliness, stability and reliability. Radiance behind the debris mitigation system was confirmed to be 120 W/mm2/sr at 9 kHz and peak radiance at the plasma was increased to over 200 W/mm2/sr in the recent development which supports high-throughput, high-precision mask inspection in the current and future technology nodes. One of the unique features of Ushio's LDP source is cleanliness. Cleanliness evaluation using both grazing-incidence Ru mirrors and normal-incidence Mo/Si mirrors showed no considerable damage to the mirrors other than smooth sputtering of the surface at the pace of a few nm per Gpulse. In order to prove the system reliability, several long-term tests were performed. Data recorded during the tests was analyzed to assess two-dimensional radiance stability. In addition, several operating parameters were monitored to figure out which contributes to the radiance stability. The latest model that features a large opening angle was recently developed so that the tool can utilize a large number of debris-free photons behind the debris shield. The model was designed both for beam line application and high-throughput mask inspection application. At the time of publication, the first product is supposed to be in use at the customer site.

  1. The Goddard Snow Radiance Assimilation Project: An Integrated Snow Radiance and Snow Physics Modeling Framework for Snow/cold Land Surface Modeling

    NASA Technical Reports Server (NTRS)

    Kim, E.; Tedesco, M.; Reichle, R.; Choudhury, B.; Peters-Lidard C.; Foster, J.; Hall, D.; Riggs, G.

    2006-01-01

    Microwave-based retrievals of snow parameters from satellite observations have a long heritage and have so far been generated primarily by regression-based empirical "inversion" methods based on snapshots in time. Direct assimilation of microwave radiance into physical land surface models can be used to avoid errors associated with such retrieval/inversion methods, instead utilizing more straightforward forward models and temporal information. This approach has been used for years for atmospheric parameters by the operational weather forecasting community with great success. Recent developments in forward radiative transfer modeling, physical land surface modeling, and land data assimilation are converging to allow the assembly of an integrated framework for snow/cold lands modeling and radiance assimilation. The objective of the Goddard snow radiance assimilation project is to develop such a framework and explore its capabilities. The key elements of this framework include: a forward radiative transfer model (FRTM) for snow, a snowpack physical model, a land surface water/energy cycle model, and a data assimilation scheme. In fact, multiple models are available for each element enabling optimization to match the needs of a particular study. Together these form a modular and flexible framework for self-consistent, physically-based remote sensing and water/energy cycle studies. In this paper we will describe the elements and the integration plan. All modules will operate within the framework of the Land Information System (LIS), a land surface modeling framework with data assimilation capabilities running on a parallel-node computing cluster. Capabilities for assimilation of snow retrieval products are already under development for LIS. We will describe plans to add radiance-based assimilation capabilities. Plans for validation activities using field measurements will also be discussed.

  2. Thermodynamic Temperature Measurement to the Indium Point Based on Radiance Comparison

    NASA Astrophysics Data System (ADS)

    Yamaguchi, Y.; Yamada, Y.

    2017-04-01

    A multi-national project (the EMRP InK project) was completed recently, which successfully determined the thermodynamic temperatures of several of the high-temperature fixed points above the copper point. The National Metrology Institute of Japan contributed to this project with its newly established absolute spectral radiance calibration capability. In the current study, we have extended the range of thermodynamic temperature measurement to below the copper point and measured the thermodynamic temperatures of the indium point (T_{90} = 429.748 5 K), tin point (505.078 K), zinc point (692.677 K), aluminum point (933.473 K) and the silver point (1 234.93 K) by radiance comparison against the copper point, with a set of radiation thermometers having center wavelengths ranging from 0.65 μm to 1.6 μm. The copper-point temperature was measured by the absolute radiation thermometer which was calibrated by radiance method traceable to the electrical substitution cryogenic radiometer. The radiance of the fixed-point blackbodies was measured by standard radiation thermometers whose spectral responsivity and nonlinearity are precisely evaluated, and then the thermodynamic temperatures were determined from radiance ratios to the copper point. The values of T-T_{90} for the silver-, aluminum-, zinc-, tin- and indium-point cells were determined as -4 mK (U = 104 mK, k=2), -99 mK (88 mK), -76 mK (76 mK), -68 mK (163 mK) and -42 mK (279 mK), respectively.

  3. ENVIRONMENTAL TECHNOLOGY INITIATIVE: CHEMICAL-FREE CLEANING OF SEMICONDUCTORS BY THE RADIANCE PROCESS

    EPA Science Inventory

    The Radiance Process is a patented dry process for removing contaminants from surfaces. It uses light, usually from a pulsed laser and a gas inert to the surface, to entrain released contaminants. The focus of this effort is to assess the applicability of the Radiance Process t...

  4. Interior radiances in optically deep absorbing media. III Scattering from Haze L

    NASA Technical Reports Server (NTRS)

    Kattawar, G. W.; Plass, G. N.

    1975-01-01

    The interior radiances are calculated within an optically deep absorbing medium scattering according to the Haze L phase function. The dependence on the solar zenith angle, the single scattering albedo, and the optical depth within the medium is calculated by the matrix operator method. The development of the asymptotic angular distribution of the radiance in the diffusion region is illustrated through a number of examples; it depends only on the single scattering albedo and on the phase function for single scattering. The exact values of the radiance in the diffusion region are compared with values calculated from the approximate equations proposed by Van de Hulst. The variation of the radiance near the lower boundary of an optically thick medium is illustrated with examples. The attenuation length is calculated for various single scattering albedos and compared with the corresponding values for Rayleigh scattering. The ratio of the upward to the downward flux is found to be remarkably constant within the medium.

  5. Spectral and Spatial UV Sky Radiance Measurements at a Seaside Resort Under Clear Sky and Slightly Overcast Conditions.

    PubMed

    Sandmann, Henner; Stick, Carsten

    2014-01-01

    Spatial measurements of the diffusely scattered sky radiance at a seaside resort under clear sky and slightly overcast conditions have been used to calculate the sky radiance distribution across the upper hemisphere. The measurements were done in the summer season when solar UV radiation is highest. The selected wavelengths were 307, 350 and 550 nm representing the UVB, UVA and VIS band. Absolute values of radiance differ considerably between the wavelengths. Normalizing the measured values by use of direct solar radiance made the spatial distributions of unequal sky radiance comparable. The results convey a spatial impression of the different distributions of the radiance at the three wavelengths. Relative scattered radiance intensity is one order of magnitude greater in UVB than in VIS, whereas in UVA lies roughly in between. Under slightly overcast conditions scattered radiance is increased at all three wavelengths by about one order of magnitude. These measurements taken at the seaside underline the importance of diffuse scattered radiance. The effect of shading parts of the sky can be estimated from the distribution of sky radiance. This knowledge might be useful for sun seekers and in the treatment of people staying at the seaside for therapeutic purposes. © 2013 The American Society of Photobiology.

  6. Nonuniformity correction of infrared cameras by reading radiance temperatures with a spatially nonhomogeneous radiation source

    NASA Astrophysics Data System (ADS)

    Gutschwager, Berndt; Hollandt, Jörg

    2017-01-01

    We present a novel method of nonuniformity correction (NUC) of infrared cameras and focal plane arrays (FPA) in a wide optical spectral range by reading radiance temperatures and by applying a radiation source with an unknown and spatially nonhomogeneous radiance temperature distribution. The benefit of this novel method is that it works with the display and the calculation of radiance temperatures, it can be applied to radiation sources of arbitrary spatial radiance temperature distribution, and it only requires sufficient temporal stability of this distribution during the measurement process. In contrast to this method, an initially presented method described the calculation of NUC correction with the reading of monitored radiance values. Both methods are based on the recording of several (at least three) images of a radiation source and a purposeful row- and line-shift of these sequent images in relation to the first primary image. The mathematical procedure is explained in detail. Its numerical verification with a source of a predefined nonhomogeneous radiance temperature distribution and a thermal imager of a predefined nonuniform FPA responsivity is presented.

  7. Establishing the moon as a spectral radiance standard

    USGS Publications Warehouse

    Kieffer, H.H.; Wildey, R.L.

    1996-01-01

    A new automated observatory dedicated to the radiometry of the moon has been constructed to provide new radiance information for calibration of earth-orbiting imaging instruments, particularly Earth Observing System instruments. Instrumentation includes an imaging photometer with 4.5-in. resolution on a fully digital mount and a full-aperture radiance calibration source. Interference filters within 0.35-0.95 ??m correspond to standard stellar magnitude systems, accommodate wavelengths of lunar spectral contrast, and approximate some band-passes of planned earth-orbiting instruments (ASTER, Landsat-7 ETM, MISR, MODIS, and SeaWIFS). The same equipment is used for lunar and stellar observations, with the use of an aperture stop in lunar imaging to comply with Nyquist's theorem and lengthen exposure times to avoid scintillation effects. A typical robotic night run involves observation of about 60 photometric standard stars and the moon; about 10 of the standard stars are observed repeatedly to determine atmospheric extinction, and the moon is observed several times. Observations are to be made on every photometric night during the bright half of the month for at least 4.5 years to adequately cover phase and libration variation. Each lunar image is reduced to absolute exoatmospheric radiance and reprojected to a fixed selenographic grid system. The collection of these images at various librations and phase angles will be reduced to photometric models for each of the approximately 120 000 points in the lunar grid for each filter. Radiance models of the moon can then be produced for the precise geometry of an orbiting instrument observation. Expected errors are under 1% relative and 2.5% absolute. A second telescope operating from 1.0 to 2.5 ??m is planned.

  8. Improved Impact of Atmospheric Infrared Sounder (AIRS) Radiance Assimilation in Numerical Weather Prediction

    NASA Technical Reports Server (NTRS)

    Zavodsky, Bradley; Chou, Shih-Hung; Jedlovec, Gary

    2012-01-01

    Improvements to global and regional numerical weather prediction (NWP) have been demonstrated through assimilation of data from NASA s Atmospheric Infrared Sounder (AIRS). Current operational data assimilation systems use AIRS radiances, but impact on regional forecasts has been much smaller than for global forecasts. Retrieved profiles from AIRS contain much of the information that is contained in the radiances and may be able to reveal reasons for this reduced impact. Assimilating AIRS retrieved profiles in an identical analysis configuration to the radiances, tracking the quantity and quality of the assimilated data in each technique, and examining analysis increments and forecast impact from each data type can yield clues as to the reasons for the reduced impact. By doing this with regional scale models individual synoptic features (and the impact of AIRS on these features) can be more easily tracked. This project examines the assimilation of hyperspectral sounder data used in operational numerical weather prediction by comparing operational techniques used for AIRS radiances and research techniques used for AIRS retrieved profiles. Parallel versions of a configuration of the Weather Research and Forecasting (WRF) model with Gridpoint Statistical Interpolation (GSI) that mimics the analysis methodology, domain, and observational datasets for the regional North American Mesoscale (NAM) model run at the National Centers for Environmental Prediction (NCEP)/Environmental Modeling Center (EMC) are run to examine the impact of each type of AIRS data set. The first configuration will assimilate the AIRS radiance data along with other conventional and satellite data using techniques implemented within the operational system; the second configuration will assimilate AIRS retrieved profiles instead of AIRS radiances in the same manner. Preliminary results of this study will be presented and focus on the analysis impact of the radiances and profiles for selected cases.

  9. Role of laser beam radiance in different ceramic processing: A two wavelengths comparison

    NASA Astrophysics Data System (ADS)

    Shukla, Pratik; Lawrence, Jonathan

    2013-12-01

    Effects of laser beam radiance (brightness) of the fibre and the Nd3+:YAG laser were investigated during surface engineering of the ZrO2 and Si3N4 advanced ceramics with respect to dimensional size and microstructure of both of the advanced ceramics. Using identical process parameters, the effects of radiance of both the Nd3+:YAG laser and a fibre laser were compared thereon the two selected advanced ceramics. Both the lasers showed differences in each of the ceramics employed in relation to the microstructure and grain size as well as the dimensional size of the laser engineered tracks-notwithstanding the use of identical process parameters namely spot size; laser power; traverse speed; Gaussian beam modes; gas flow rate and gas composition as well the wavelengths. From this it was evident that the difference in the laser beam radiance between the two lasers would have had much to do with this effect. The high radiance fibre laser produced larger power per unit area in steradian when compared to the lower radiance of the Nd3+:YAG laser. This characteristically produced larger surface tracks through higher interaction temperature at the laser-ceramic interface. This in turn generated bigger melt-zones and different cooling rates which then led to the change in the microstructure of both the Si3N4 and ZrO2 advance ceramics. Owing to this, it was indicative that lasers with high radiance would result in much cheaper and cost effective laser assisted surface engineering processes, since lower laser power, faster traverse speeds, larger spot sizes could be used in comparison to lasers with lower radiance which require much slower traverse speed, higher power levels and finer spot sizes to induce the same effect thereon materials such as the advanced ceramics.

  10. Structures observed on the spot radiance fields during the FIRE experiment

    NASA Technical Reports Server (NTRS)

    Seze, Genevieve; Smith, Leonard; Desbois, Michel

    1990-01-01

    Three Spot images taken during the FIRE experiment on stratocumulus are analyzed. From this high resolution data detailed observations of the true cloud radiance field may be made. The structure and inhomogeneity of these radiance fields hold important implications for the radiation budget, while the fine scale structure in radiance field provides information on cloud dynamics. Wieliki and Welsh, and Parker et al., have quantified the inhomogeneities of the cumulus clouds through a careful examination of the distribution of cloud (and hole) size as functions of an effective cloud diameter and radiance threshold. Cahalan (1988) has compared for different cloud types of (stratocumulus, fair weather cumulus, convective clouds in the ITCZ) the distributions of clouds (and holes) sizes, the relation between the size and the perimeter of these clouds (and holes), and examining the possibility of scale invariance. These results are extended from LANDSAT resolution (57 m and 30 m) to the Spot resolution (10 m) resolution in the case of boundary layer clouds. Particular emphasis is placed on the statistics of zones of high and low reflectivity as a function of a threshold reflectivity.

  11. Iterative discrete ordinates solution of the equation for surface-reflected radiance

    NASA Astrophysics Data System (ADS)

    Radkevich, Alexander

    2017-11-01

    This paper presents a new method of numerical solution of the integral equation for the radiance reflected from an anisotropic surface. The equation relates the radiance at the surface level with BRDF and solutions of the standard radiative transfer problems for a slab with no reflection on its surfaces. It is also shown that the kernel of the equation satisfies the condition of the existence of a unique solution and the convergence of the successive approximations to that solution. The developed method features two basic steps: discretization on a 2D quadrature, and solving the resulting system of algebraic equations with successive over-relaxation method based on the Gauss-Seidel iterative process. Presented numerical examples show good coincidence between the surface-reflected radiance obtained with DISORT and the proposed method. Analysis of contributions of the direct and diffuse (but not yet reflected) parts of the downward radiance to the total solution is performed. Together, they represent a very good initial guess for the iterative process. This fact ensures fast convergence. The numerical evidence is given that the fastest convergence occurs with the relaxation parameter of 1 (no relaxation). An integral equation for BRDF is derived as inversion of the original equation. The potential of this new equation for BRDF retrievals is analyzed. The approach is found not viable as the BRDF equation appears to be an ill-posed problem, and it requires knowledge the surface-reflected radiance on the entire domain of both Sun and viewing zenith angles.

  12. Self Validation of Radiance Measurements from the CERES (TRMM)Instrument

    NASA Technical Reports Server (NTRS)

    Paden, Jack; Pandey, Dhirendra K.; Lee, Robert B., III; Priestley, Kory J.

    1999-01-01

    Eight continuous months of earth-nadir-viewing radiance measurements from the 3-channel Tropical Rainfall Measuring Mission (TRMM,) Clouds and the Earth's Radiant Energy System (CERES) scanning radiometric measurement instrument, have been analyzed. While previous remote sensing satellites, such as the Earth Radiation Budget Experiment (ERBE) covered all subsets of the broadband radiance spectrum (total, longwave and shortwave.) CERES has two subset channels (window and shortwave) which do not give continuous frequency coverage over the total band. Previous experience with ERBE indicated the need for us to model the equivalent daytime longwave radiance using a window channel regression, which will allow us to validate the performance of the instrument using a three-channel inter-comparison. Limiting our consideration to the fixed azimuth plane, cross-track, scanning mode (FAPS), each nadir-viewing measurement was averaged into three subjective categories called daytime, nighttime, and twilight. Daytime was defined as any measurement taken when the solar zenith angle (SZA) was less than 90 ; nighttime was taken to be any measurement where the SZA was greater than 117 ; and twilight was everything else. Our analysis indicates that there are only two distinct categories of nadir-view data; daytime, and non-daytime (i.e., the union of the nighttime and twilight sets); and that the CERES longwave radiance is predictable to an accuracy of 1%, based on the SZA, and window channel measurements.

  13. Technology for detecting spectral radiance by a snapshot multi-imaging spectroradiometer

    NASA Astrophysics Data System (ADS)

    Zuber, Ralf; Stührmann, Ansgar; Gugg-Helminger, Anton; Seckmeyer, Gunther

    2017-12-01

    Technologies to determine spectral sky radiance distributions have evolved in recent years and have enabled new applications in remote sensing, for sky radiance measurements, in biological/diagnostic applications and luminance measurements. Most classical spectral imaging radiance technologies are based on mechanical and/or spectral scans. However, these methods require scanning time in which the spectral radiance distribution might change. To overcome this limitation, different so-called snapshot spectral imaging technologies have been developed that enable spectral and spatial non-scanning measurements. We present a new setup based on a facet mirror that is already used in imaging slicing spectrometers. By duplicating the input image instead of slicing it and using a specially designed entrance slit, we are able to select nearly 200 (14 × 14) channels within the field of view (FOV) for detecting spectral radiance in different directions. In addition, a megapixel image of the FOV is captured by an additional RGB camera. This image can be mapped onto the snapshot spectral image. In this paper, the mechanical setup, technical design considerations and first measurement results of a prototype are presented. For a proof of concept, the device is radiometrically calibrated and a 10 mm × 10 mm test pattern measured within a spectral range of 380 nm-800 nm with an optical bandwidth of 10 nm (full width at half maximum or FWHM). To show its potential in the UV spectral region, zenith sky radiance measurements in the UV of a clear sky were performed. Hence, the prototype was equipped with an entrance optic with a FOV of 0.5° and modified to obtain a radiometrically calibrated spectral range of 280 nm-470 nm with a FWHM of 3 nm. The measurement results have been compared to modeled data processed by UVSPEC, which showed deviations of less than 30%. This is far from being ideal, but an acceptable result with respect to available state

  14. NIST TXR Validation of S-HIS radiances and a UW-SSEC Blackbody

    NASA Astrophysics Data System (ADS)

    Taylor, J. K.; O'Connell, J.; Rice, J. P.; Revercomb, H. E.; Best, F. A.; Tobin, D. C.; Knuteson, R. O.; Adler, D. P.; Ciganovich, N. C.; Dutcher, S. T.; Laporte, D. D.; Ellington, S. D.; Werner, M. W.; Garcia, R. K.

    2007-12-01

    The ability to accurately validate infrared spectral radiances measured from space by direct comparison with airborne spectrometer radiances was first demonstrated using the Scanning High-resolution Interferometer Sounder (S-HIS) aircraft instrument flown under the AIRS on the NASA Aqua spacecraft in 2002 with subsequent successful comparisons in 2004 and 2006. The comparisons span a range of conditions, including arctic and tropical atmospheres, daytime and nighttime, and ocean and land surfaces. Similar comprehensive and successful comparisons have also been conducted with S-HIS for the MODIS sensors, the Tropospheric Emission Spectrometer (TES), and most recently the MetOp Infrared Atmospheric Sounding Interferometer (IASI). These comparisons are part of a larger picture that already shows great progress toward transforming our ability to make, and verify, highly accurate spectral radiance observations from space. A key challenge, especially for climate, is to carefully define the absolute accuracy of satellite radiances. Our vision of the near-term future of spectrally resolved infrared radiance observation includes a new space-borne mission that provides benchmark observations of the emission spectrum for climate. This concept, referred to as the CLimate Absolute Radiance and REfractivity Observatory (CLARREO) in the recent NRC Decadal Survey provides more complete spectral and time-of-day coverage and would fly basic physical standards to eliminate the need to assume on-board reference stability. Therefore, the spectral radiances from this mission will also serve as benchmarks to propagate a highly accurate calibration to other space-borne IR instruments. For the current approach of calibrating infrared flight sensors, in which thermal vacuum tests are conducted before launch and stability is assumed after launch, in-flight calibration validation is essential for highly accurate applications. At present, airborne observations provide the only source of direct

  15. Bioluminescence in a complex coastal environment: 1. Temporal dynamics of nighttime water-leaving radiance

    NASA Astrophysics Data System (ADS)

    Moline, Mark A.; Oliver, Matthew J.; Mobley, Curtis D.; Sundman, Lydia; Bensky, Thomas; Bergmann, Trisha; Bissett, W. Paul; Case, James; Raymond, Erika H.; Schofield, Oscar M. E.

    2007-11-01

    Nighttime water-leaving radiance is a function of the depth-dependent distribution of both the in situ bioluminescence emissions and the absorption and scattering properties of the water. The vertical distributions of these parameters were used as inputs for a modified one-dimensional radiative transfer model to solve for spectral bioluminescence water-leaving radiance from prescribed depths of the water column. Variation in the water-leaving radiance was consistent with local episodic physical forcing events, with tidal forcing, terrestrial runoff, particulate accumulation, and biological responses influencing the shorter timescale dynamics. There was a >90 nm shift in the peak water-leaving radiance from blue (˜474 nm) to green as light propagated to the surface. In addition to clues in ecosystem responses to physical forcing, the temporal dynamics in intensity and spectral quality of water-leaving radiance provide suitable ranges for assessing detection. This may provide the information needed to estimate the depth of internal light sources in the ocean, which is discussed in part 2 of this paper.

  16. P161 Improved Impact of Atmospheric Infrared Sounder (AIRS) Radiance Assimilation in Numerical Weather Prediction

    NASA Technical Reports Server (NTRS)

    Zavodsky, Bradley T.; Chou, Shih-Hung; Jedlovec, Gary J.

    2012-01-01

    For over 6 years, AIRS radiances have been assimilated operationally into National (e.g. Environmental Modeling Center (EMC)) and International (e.g. European Centre for Medium-Range Weather Forecasts (ECMWF)), operational centers; assimilated in the North American Mesoscale (NAM) since 2008. Due partly to data latency and operational constraints, hyperspectral radiance assimilation has had less impact on the Gridpoint Statistical Interpolation (GSI) system used in the NAM and GFS. Objective of this project is to use AIRS retrieved profiles as a proxy for the AIRS radiances in situations where AIRS radiances are unable to be assimilated in the current operational system by evaluating location and magnitude of analysis increments.

  17. Downscaling Thermal Infrared Radiance for Subpixel Land Surface Temperature Retrieval

    PubMed Central

    Liu, Desheng; Pu, Ruiliang

    2008-01-01

    Land surface temperature (LST) retrieved from satellite thermal sensors often consists of mixed temperature components. Retrieving subpixel LST is therefore needed in various environmental and ecological studies. In this paper, we developed two methods for downscaling coarse resolution thermal infrared (TIR) radiance for the purpose of subpixel temperature retrieval. The first method was developed on the basis of a scale-invariant physical model on TIR radiance. The second method was based on a statistical relationship between TIR radiance and land cover fraction at high spatial resolution. The two methods were applied to downscale simulated 990-m ASTER TIR data to 90-m resolution. When validated against the original 90-m ASTER TIR data, the results revealed that both downscaling methods were successful in capturing the general patterns of the original data and resolving considerable spatial details. Further quantitative assessments indicated a strong agreement between the true values and the estimated values by both methods. PMID:27879844

  18. Downscaling Thermal Infrared Radiance for Subpixel Land Surface Temperature Retrieval.

    PubMed

    Liu, Desheng; Pu, Ruiliang

    2008-04-06

    Land surface temperature (LST) retrieved from satellite thermal sensors often consists of mixed temperature components. Retrieving subpixel LST is therefore needed in various environmental and ecological studies. In this paper, we developed two methods for downscaling coarse resolution thermal infrared (TIR) radiance for the purpose of subpixel temperature retrieval. The first method was developed on the basis of a scale-invariant physical model on TIR radiance. The second method was based on a statistical relationship between TIR radiance and land cover fraction at high spatial resolution. The two methods were applied to downscale simulated 990-m ASTER TIR data to 90-m resolution. When validated against the original 90-m ASTER TIR data, the results revealed that both downscaling methods were successful in capturing the general patterns of the original data and resolving considerable spatial details. Further quantitative assessments indicated a strong agreement between the true values and the estimated values by both methods.

  19. The effects of downwelling radiance on MER surface spectra: the evil that atmospheres do

    NASA Astrophysics Data System (ADS)

    Wolff, M.; Ghosh, A.; Arvidson, R.; Christensen, P.; Guinness, E.; Ruff, S.; Seelos, F.; Smith, M.; Athena Science

    2004-11-01

    While it may not be surprising to some that downwelling radiation in the martian atmosphere may contribute a non-negligible fraction of the radiance for a given surface scene, others remain shocked and surprised (and often dismayed) to discover this fact; particularly with regard to mini-TES observations. Naturally, the relative amplitude of this sky ``contamination'' is often a complicated function of meteorological conditions, viewing geometry, surface properties, and (for the IR) surface temperature. Ideally, one would use a specialized observations to mimic the actual hemispherical-directional nature of the problem. Despite repeated attempts to obtain Pancam complete sky observations and mini-TES sky octants, such observations are not available in the MER observational database. As a result, one is left with the less-enviable, though certainly more computationally intensive, task of connecting point observations (radiance and derived meteorological parameters) to a hemispherical integral of downwelling radiance. Naturally, one must turn to a radiative transfer analysis, despite oft-repeated attempts to assert otherwise. In our presentation, we offer insight into the conditions under which one must worry about atmospheric removal, as well as semi-empirical approaches (based upon said radiative transfer efforts) for producing the correction factors from the available MER atmospheric observations. This work is proudly supported by the MER program through NASA/JPL Contract No. 1242889 (MJW), as well as the contracts for the co-authors.

  20. Experimental and Metrological Basis for SI-Traceable Infrared Radiance Measurements From Space

    NASA Astrophysics Data System (ADS)

    Gero, P. J.; Dykema, J. A.; Anderson, J. G.; Leroy, S. S.

    2007-12-01

    In order to establish a climate benchmark record and to be useful in interdecadal climate forecast testing, satellite measurements of high spectral resolution infrared radiance must have uncertainty estimates that can be proven beyond a doubt. An uncertainty in radiance of about 1 part in 1000 is required for climate applications. This can be accomplished by appealing to the best measurement practices of the metrology community. The International System of Units (SI) are linked to fundamental physical properties of matter, and can be realized anywhere in the world without bias. By doing so, one can make an accurate observation to within a specified uncertainty. Achieving SI-traceable radiance measurements from space is a novel requirement, and requires specialized sensor design and a disciplined experimental approach. Infrared remote sensing satellite instruments typically employ blackbody calibration targets, which are tied to the SI through Planck's law and the definition of the Kelvin. The blackbody temperature and emissivity, however, must be determined accurately on- orbit, in order for the blackbody emission scale to be SI-traceable. We outline a methodology of instrument design, pre-flight calibration and on-orbit diagnostics for realizing SI- traceable infrared radiance measurements. This instrument is intended as a component of the Climate Absolute Radiance and Refractivity Earth Observatory (CLARREO), a high priority recommendation of the National Research Council decadal survey. Calibration blackbodies for remote sensing differ from a perfect Planckian blackbody; thus the component uncertainties must be evaluated in order to confer traceability. We have performed traceability experiments in the laboratory to verify blackbody temperature, emissivity and the end-to-end radiance scale. We discuss the design of the Harvard standard blackbody and an intercomparison campaign that will be conducted with the GIFTS blackbody (University of Wisconsin, Madison) and

  1. [Application of BaSO4 diffuser plate in 250-400 nm spectral radiance calibration].

    PubMed

    Jia, Hui; Li, Fu-tian

    2004-01-01

    Sprayed BaSO4 diffuser plate is the most Lambertian surface actually used in spectral radiance calibration known by now. Its hemispheric reflectance and Bi-directional Reflectance Distribution Functions (BRDF) were measured in the experiment. Its diffuse characteristics were compared with Lambertian surface. In order to calibrate spectral radiance more accurately, the small variation of diffuser's BRDF with scattered angles and the nonuniformity of spectral irradiance on diffuser surface illuminated by the standard lamp should be considered. By integrating the radiation flux reflected by the element area and that entering the entrance slit within the viewing area of spectrometer, the measured spectral radiance can be calculated. Furthermore, the spectral radiance of Lambertian surface whose BRDF was derived from hemispheric reflectance was compared with that from the average of the measured BRDF.

  2. Use of MODIS Cloud Top Pressure to Improve Assimilation Yields of AIRS Radiances in GSI

    NASA Technical Reports Server (NTRS)

    Zavodsky, Bradley; Srikishen, Jayanthi

    2014-01-01

    Radiances from hyperspectral sounders such as the Atmospheric Infrared Sounder (AIRS) are routinely assimilated both globally and regionally in operational numerical weather prediction (NWP) systems using the Gridpoint Statistical Interpolation (GSI) data assimilation system. However, only thinned, cloud-free radiances from a 281-channel subset are used, so the overall percentage of these observations that are assimilated is somewhere on the order of 5%. Cloud checks are performed within GSI to determine which channels peak above cloud top; inaccuracies may lead to less assimilated radiances or introduction of biases from cloud-contaminated radiances.Relatively large footprint from AIRS may not optimally represent small-scale cloud features that might be better resolved by higher-resolution imagers like the Moderate Resolution Imaging Spectroradiometer (MODIS). Objective of this project is to "swap" the MODIS-derived cloud top pressure (CTP) for that designated by the AIRS-only quality control within GSI to test the hypothesis that better representation of cloud features will result in higher assimilated radiance yields and improved forecasts.

  3. Aureole radiance field about a source in a scattering-absorbing medium.

    PubMed

    Zachor, A S

    1978-06-15

    A technique is described for computing the aureole radiance field about a point source in a medium that absorbs and scatters according to an arbitrary phase function. When applied to an isotropic source in a homogenous medium, the method uses a double-integral transform which is evaluated recursively to obtain the aureole radiances contributed by successive scattering orders, as in the Neumann solution of the radiative transfer equation. The normalized total radiance field distribution and the variation of flux with field of view and range are given for three wavelengths in the uv and one in the visible, for a sea-level model atmosphere assumed to scatter according to a composite of the Rayleigh and modified Henyey-Greenstein phase functions. These results have application to the detection and measurement of uncollimated uv and visible sources at short ranges in the lower atmosphere.

  4. Quantitative Spectral Radiance Measurements in the HYMETS Arc Jet

    NASA Technical Reports Server (NTRS)

    Danehy, Paul M.; Hires, Drew V.; Johansen, Craig T.; Bathel, Brett F.; Jones, Stephen B.; Gragg, Jeffrey G.; Splinter, Scott C.

    2012-01-01

    Calibrated spectral radiance measurements of gaseous emission spectra have been obtained from the HYMETS (Hypersonic Materials Environmental Test System) 400 kW arc-heated wind tunnel at NASA Langley Research Center. A fiber-optic coupled spectrometer collected natural luminosity from the flow. Spectral radiance measurements are reported between 340 and 1000 nm. Both Silicon Carbide (SiC) and Phenolic Impregnated Carbon Ablator (PICA) samples were placed in the flow. Test gases studied included a mostly-N2 atmosphere (95% nitrogen, 5% argon), a simulated Earth Air atmosphere (75% nitrogen, 20% oxygen, 5% argon) and a simulated Martian atmosphere (71% carbon dioxide, 24% nitrogen, 5% argon). The bulk enthalpy of the flow was varied as was the location of the measurement. For the intermediate flow enthalpy tested (20 MJ/kg), emission from the Mars simulant gas was about 10 times higher than the Air flow and 15 times higher than the mostly-N2 atmosphere. Shock standoff distances were estimated from the spectral radiance measurements. Within-run, run-to-run and day-to-day repeatability of the emission were studied, with significant variations (15-100%) noted.

  5. Radiance and polarization in the diffusion region with an arbitrary scattering phase matrix

    NASA Astrophysics Data System (ADS)

    Sun, Bingqiang; Kattawar, George W.; Yang, Ping

    2016-11-01

    Radiance and polarization patterns in an optically deep region, the so-called diffusion region or asymptotic region, of a homogeneous atmosphere or ocean, depend mainly on the scattering phase matrix and the single-scattering albedo of the medium. The radiance and polarization properties in the diffusion region for an arbitrary scattering phase matrix can be obtained in terms of a series of the generalized spherical functions. The number of terms is closely related to the single-scattering albedo of the medium. If the medium is conservative, the radiance is isotropic in conjunction with no polarization. If the single-scattering albedo is close to 1, several terms are sufficient to obtain the patterns, in which the degree of polarization feature is less than 1%. If the medium is highly absorptive, more expansion terms are required to obtain the diffusion patterns. The examples of simulated radiance and polarization patterns for Rayleigh scattering, Henyey-Greenstein-Rayleigh scattering, and haze L and cloud C1 scattering, defined by Deirmendjian, are calculated.

  6. Spectral Invariant Behavior of Zenith Radiance Around Cloud Edges Observed by ARM SWS

    NASA Technical Reports Server (NTRS)

    Marshak, A.; Knyazikhin, Y.; Chiu, J. C.; Wiscombe, W. J.

    2009-01-01

    The ARM Shortwave Spectrometer (SWS) measures zenith radiance at 418 wavelengths between 350 and 2170 nm. Because of its 1-sec sampling resolution, the SWS provides a unique capability to study the transition zone between cloudy and clear sky areas. A spectral invariant behavior is found between ratios of zenith radiance spectra during the transition from cloudy to cloud-free. This behavior suggests that the spectral signature of the transition zone is a linear mixture between the two extremes (definitely cloudy and definitely clear). The weighting function of the linear mixture is a wavelength-independent characteristic of the transition zone. It is shown that the transition zone spectrum is fully determined by this function and zenith radiance spectra of clear and cloudy regions. An important result of these discoveries is that high temporal resolution radiance measurements in the clear-to-cloud transition zone can be well approximated by lower temporal resolution measurements plus linear interpolation.

  7. Deriving mesoscale temperature and moisture fields from satellite radiance measurements over the United States

    NASA Technical Reports Server (NTRS)

    Hillger, D. W.; Vonder Haar, T. H.

    1977-01-01

    The ability to provide mesoscale temperature and moisture fields from operational satellite infrared sounding radiances over the United States is explored. High-resolution sounding information for mesoscale analysis and forecasting is shown to be obtainable in mostly clear areas. An iterative retrieval algorithm applied to NOAA-VTPR radiances uses a mean radiosonde sounding as a best initial-guess profile. Temperature soundings are then retrieved at a horizontal resolution of about 70 km, as is an indication of the precipitable water content of the vertical sounding columns. Derived temperature values may be biased in general by the initial-guess sounding or in certain areas by the cloud correction technique, but the resulting relative temperature changes across the field when not contaminated by clouds will be useful for mesoscale forecasting and models. The derived moisture, affected only by high clouds, proves to be reliable to within 0.5 cm of precipitable water and contains valuable horizontal information. Present-day applications from polar-orbiting satellites as well as possibilities from upcoming temperature and moisture sounders on geostationary satellites are noted.

  8. Spatially-resolved probing of biological phantoms by point-radiance spectroscopy

    NASA Astrophysics Data System (ADS)

    Grabtchak, Serge; Palmer, Tyler J.; Whelan, William M.

    2011-03-01

    Interstitial fiber-optic based strategies for therapy monitoring and assessment rely on detecting treatment-induced changes in the light distribution in biological tissues. We present an optical technique to identify spectrally and spatially specific tissue chromophores in highly scattering turbid media. Typical optical sensors measure non-directional light intensity (i.e. fluence) and require fiber translation (i.e. 3-5 positions), which is difficult to implement clinically. Point radiance spectroscopy is based on directional light collection (i.e. radiance) at a single point with a side-firing fiber that can be rotated up to 360°. A side firing fiber accepts light within a well-defined solid angle thus potentially providing an improved spatial resolution. Experimental measurements were performed using an 800-μm diameter isotropic spherical diffuser coupled to a halogen light source and a 600 μm, ~43° cleaved fiber (i.e. radiance detector). The background liquid-based scattering phantom was fabricated using 1% Intralipid (i.e. scattering medium). Light was collected at 1-5° increments through 360°-segment. Gold nanoparticles, placed into a 3.5 mm diameter capillary tube were used as localized scatterers and absorbers introduced into the liquid phantom both on- and off-axis between source and detector. The localized optical inhomogeneity was detectable as an angular-resolved variation in the radiance polar plots. This technique is being investigated as a non-invasive optical modality for prostate cancer monitoring.

  9. The Impact of Assimilation of GPM Clear Sky Radiance on HWRF Hurricane Track and Intensity Forecasts

    NASA Astrophysics Data System (ADS)

    Yu, C. L.; Pu, Z.

    2016-12-01

    The impact of GPM microwave imager (GMI) clear sky radiances on hurricane forecasting is examined by ingesting GMI level 1C recalibrated brightness temperature into the NCEP Gridpoint Statistical Interpolation (GSI)- based ensemble-variational hybrid data assimilation system for the operational Hurricane Weather Research and Forecast (HWRF) system. The GMI clear sky radiances are compared with the Community Radiative Transfer Model (CRTM) simulated radiances to closely study the quality of the radiance observations. The quality check result indicates the presence of bias in various channels. A static bias correction scheme, in which the appropriate bias correction coefficients for GMI data is evaluated by applying regression method on a sufficiently large sample of data representative to the observational bias in the regions of concern, is used to correct the observational bias in GMI clear sky radiances. Forecast results with and without assimilation of GMI radiance are compared using hurricane cases from recent hurricane seasons (e.g., Hurricane Joaquin in 2015). Diagnoses of data assimilation results show that the bias correction coefficients obtained from the regression method can correct the inherent biases in GMI radiance data, significantly reducing observational residuals. The removal of biases also allows more data to pass GSI quality control and hence to be assimilated into the model. Forecast results for hurricane Joaquin demonstrates that the quality of analysis from the data assimilation is sensitive to the bias correction, with positive impacts on the hurricane track forecast when systematic biases are removed from the radiance data. Details will be presented at the symposium.

  10. Equivalent Sensor Radiance Generation and Remote Sensing from Model Parameters. Part 1; Equivalent Sensor Radiance Formulation

    NASA Technical Reports Server (NTRS)

    Wind, Galina; DaSilva, Arlindo M.; Norris, Peter M.; Platnick, Steven E.

    2013-01-01

    In this paper we describe a general procedure for calculating equivalent sensor radiances from variables output from a global atmospheric forecast model. In order to take proper account of the discrepancies between model resolution and sensor footprint the algorithm takes explicit account of the model subgrid variability, in particular its description of the probably density function of total water (vapor and cloud condensate.) The equivalent sensor radiances are then substituted into an operational remote sensing algorithm processing chain to produce a variety of remote sensing products that would normally be produced from actual sensor output. This output can then be used for a wide variety of purposes such as model parameter verification, remote sensing algorithm validation, testing of new retrieval methods and future sensor studies. We show a specific implementation using the GEOS-5 model, the MODIS instrument and the MODIS Adaptive Processing System (MODAPS) Data Collection 5.1 operational remote sensing cloud algorithm processing chain (including the cloud mask, cloud top properties and cloud optical and microphysical properties products.) We focus on clouds and cloud/aerosol interactions, because they are very important to model development and improvement.

  11. Development of Multi-Sensor Global Cloud and Radiance Composites for DSCOVR EPIC Imager with Subpixel Definition

    NASA Astrophysics Data System (ADS)

    Khlopenkov, K. V.; Duda, D. P.; Thieman, M. M.; Sun-Mack, S.; Su, W.; Minnis, P.; Bedka, K. M.

    2017-12-01

    The Deep Space Climate Observatory (DSCOVR) is designed to study the daytime Earth radiation budget by means of onboard Earth Polychromatic Imaging Camera (EPIC) and National Institute of Standards and Technology Advanced Radiometer (NISTAR). EPIC imager observes in several shortwave bands (317-780 nm), while NISTAR measures the top-of-atmosphere (TOA) whole-disk radiance in shortwave and total broadband windows. Calculation of albedo and outgoing longwave flux requires a high-resolution scene identification such as the radiance observations and cloud property retrievals from low earth orbit and geostationary satellite imagers. These properties have to be co-located with EPIC imager pixels to provide scene identification and to select anisotropic directional models, which are then used to adjust the NISTAR-measured radiance and subsequently obtain the global daytime shortwave and longwave fluxes. This work presents an algorithm for optimal merging of selected radiances and cloud properties derived from multiple satellite imagers to obtain seamless global hourly composites at 5-km resolution. The highest quality observation is selected by means of an aggregated rating which incorporates several factors such as the nearest time relative to EPIC observation, lowest viewing zenith angle, and others. This process provides a smoother transition and avoids abrupt changes in the merged composite data. Higher spatial accuracy in the composite product is achieved by using the inverse mapping with gradient search during reprojection and bicubic interpolation for pixel resampling. The composite data are subsequently remapped into the EPIC-view domain by convolving composite pixels with the EPIC point spread function (PSF) defined with a half-pixel accuracy. Within every EPIC footprint, the PSF-weighted average radiances and cloud properties are computed for each cloud phase and then stored within five data subsets (clear-sky, water cloud, ice cloud, total cloud, and no

  12. Dependence of NOAA-AVHRR recorded radiance on scan angle, atmospheric turbidity and unresolved cloud

    NASA Technical Reports Server (NTRS)

    Piwinski, D. J.; Schoch, L. B.; Duggin, M. J.; Whitehead, V.; Ryland, E.

    1984-01-01

    Experimental evidence on the scan angle and sun angle dependence of radiance recorded by the Advanced Very High Resolution Radiometer (AVHRR) devices on the NOAA-6 and NOAA-7 satellites is presented. The effects of atmospheric turbidity at various scan angles is shown, and simulations of angular anisotropy and recorded radiance are compared with the recorded digital data from the AVHRR obtained over the Great Plains area of the US. Evidence is presented on the effects of unresolved cloud on the recorded radiance and vegetative indices from uniform, vegetative targets.

  13. An Analysis of Far-Infrared Radiances Obtained By the First Instrument at Table Mountain through the Use of Radiative Transfer Calculations

    NASA Astrophysics Data System (ADS)

    Kratz, D. P.; Mlynczak, M. G.; Cageao, R.; Johnson, D. G.; Mast, J. C.

    2014-12-01

    The Far-Infrared Spectroscopy of the Troposphere (FIRST) instrument is a Fourier Transform Spectrometer with a moderately high spectral resolution (0.643 cm-1 unapodized). Designed to measure the most energetically important range (100 to 2000 cm-1) of Earth's emitted infrared spectrum, the FIRST instrument was specifically engineered to include the often overlooked far-infrared (100 to 650 cm-1). To date, the FIRST instrument has been deployed on several field missions, both balloon-borne and ground-based, with the most recent deployment occurring at NASA's Jet Propulsion Laboratory Table Mountain Facility in California during the months of September and October 2012. This deployment, located 2,285 meters above the Mojave Desert, provided an opportunity to observe down-welling radiances under low water vapor conditions, with some cases having total column water vapor amounts of approximately 2 to 3 millimeters. Such low water vapor conditions allow for stringent testing of both the FIRST instrument and the radiative transfer methods used to analyze these measurements. This study is focused on the analysis of the FIRST measurements in the far-infrared obtained during clear-sky conditions, and requires an accounting of the uncertainties in both the measured and calculated radiances. The former involves the manner in which calibration and full-sky conditions affect the radiances measured by the FIRST instrument. The latter involves not only differences in the model formulations and the uncertainties in the water vapor and temperature data provided by the radio-sonde measurements, but also the critical differences and uncertainties contained within the input line parameter databases. This study specifically explores the significant differences that can arise in the calculated radiances that are associated with the choice of a line parameter database, and how this choice affects the analysis of the FIRST measurements.

  14. Interior radiances in optically deep absorbing media. 3: Scattering from Haze L

    NASA Technical Reports Server (NTRS)

    Kattawar, G. W.; Plass, G. N.

    1974-01-01

    The interior radiances are calculated within an optically deep absorbing medium scattering according to the Haze L phase function. The dependence on the solar zenith angle, the single scattering albedo, and the optical depth within the medium is calculated by the matrix operator method. The development of the asymptotic angular distribution of the radiance in the diffusion region is illustrated through a number of examples; it depends only on the single scattering albedo and on the phase function for single scattering. The exact values of the radiance in the diffusion region are compared with values calculated from the approximate equations proposed by Van de Hulst. The variation of the radiance near the lower boundary of an optically thick medium is illustrated with examples. The attenuation length is calculated for various single scattering albedos and compared with the corresponding values for Rayleigh scattering. The ratio of the upward to the downward flux is found to be remarkably constant within the medium. The heating rate is calculated and found to have a maximum value at an optical depth of two within a Haze L layer when the sun is at the zenith.

  15. Development of multi-sensor global cloud and radiance composites for earth radiation budget monitoring from DSCOVR

    NASA Astrophysics Data System (ADS)

    Khlopenkov, Konstantin; Duda, David; Thieman, Mandana; Minnis, Patrick; Su, Wenying; Bedka, Kristopher

    2017-10-01

    The Deep Space Climate Observatory (DSCOVR) enables analysis of the daytime Earth radiation budget via the onboard Earth Polychromatic Imaging Camera (EPIC) and National Institute of Standards and Technology Advanced Radiometer (NISTAR). Radiance observations and cloud property retrievals from low earth orbit and geostationary satellite imagers have to be co-located with EPIC pixels to provide scene identification in order to select anisotropic directional models needed to calculate shortwave and longwave fluxes. A new algorithm is proposed for optimal merging of selected radiances and cloud properties derived from multiple satellite imagers to obtain seamless global hourly composites at 5-km resolution. An aggregated rating is employed to incorporate several factors and to select the best observation at the time nearest to the EPIC measurement. Spatial accuracy is improved using inverse mapping with gradient search during reprojection and bicubic interpolation for pixel resampling. The composite data are subsequently remapped into EPIC-view domain by convolving composite pixels with the EPIC point spread function defined with a half-pixel accuracy. PSF-weighted average radiances and cloud properties are computed separately for each cloud phase. The algorithm has demonstrated contiguous global coverage for any requested time of day with a temporal lag of under 2 hours in over 95% of the globe.

  16. Development of Multi-Sensor Global Cloud and Radiance Composites for Earth Radiation Budget Monitoring from DSCOVR

    NASA Technical Reports Server (NTRS)

    Khlopenkov, Konstantin; Duda, David; Thieman, Mandana; Minnis, Patrick; Su, Wenying; Bedka, Kristopher

    2017-01-01

    The Deep Space Climate Observatory (DSCOVR) enables analysis of the daytime Earth radiation budget via the onboard Earth Polychromatic Imaging Camera (EPIC) and National Institute of Standards and Technology Advanced Radiometer (NISTAR). Radiance observations and cloud property retrievals from low earth orbit and geostationary satellite imagers have to be co-located with EPIC pixels to provide scene identification in order to select anisotropic directional models needed to calculate shortwave and longwave fluxes. A new algorithm is proposed for optimal merging of selected radiances and cloud properties derived from multiple satellite imagers to obtain seamless global hourly composites at 5-kilometer resolution. An aggregated rating is employed to incorporate several factors and to select the best observation at the time nearest to the EPIC measurement. Spatial accuracy is improved using inverse mapping with gradient search during reprojection and bicubic interpolation for pixel resampling. The composite data are subsequently remapped into EPIC-view domain by convolving composite pixels with the EPIC point spread function (PSF) defined with a half-pixel accuracy. PSF-weighted average radiances and cloud properties are computed separately for each cloud phase. The algorithm has demonstrated contiguous global coverage for any requested time of day with a temporal lag of under 2 hours in over 95 percent of the globe.

  17. Additional confirmation of the validity of laboratory simulation of cloud radiances

    NASA Technical Reports Server (NTRS)

    Davis, J. M.; Cox, S. K.

    1986-01-01

    The results of a laboratory experiment are presented that provide additional verification of the methodology adopted for simulation of the radiances reflected from fields of optically thick clouds using the Cloud Field Optical Simulator (CFOS) at Colorado State University. The comparison of these data with their theoretically derived counterparts indicates that the crucial mechanism of cloud-to-cloud radiance field interaction is accurately simulated in the CFOS experiments and adds confidence to the manner in which the optical depth is scaled.

  18. Horizon Brightness Revisited: Measurements and a Model of Clear-Sky Radiances

    DTIC Science & Technology

    1994-07-20

    Clear daytime skies persistently display a subtle local maximum of radiance near the astronomical horizon. Spectroradiometry and digital image analysis confirm this maximum’s reality, and they show that its angular width and elevation vary with solar elevation, azimuth relative to the Sun, and aerosol optical depth. Many existing models of atmospheric scattering do not generate this near-horizon radiance maximum, but a simple second-order scattering model does, and it reproduces many of the maximum’s details.

  19. Polarized radiance distribution measurement of skylight. II. Experiment and data.

    PubMed

    Liu, Y; Voss, K

    1997-11-20

    Measurements of the skylight polarized radiance distribution were performed at different measurement sites, atmospheric conditions, and three wavelengths with our newly developed Polarization Radiance Distribution Camera System (RADS-IIP), an analyzer-type Stokes polarimeter. Three Stokes parameters of skylight (I, Q, U), the degree of polarization, and the plane of polarization are presented in image format. The Arago point and neutral lines have been observed with RADS-IIP. Qualitatively, the dependence of the intensity and polarization data on wavelength, solar zenith angle, and surface albedo is in agreement with the results from computations based on a plane-parallel Rayleigh atmospheric model.

  20. A Microwave Radiance Assimilation Study for a Tundra Snowpack

    NASA Technical Reports Server (NTRS)

    Kim, Edward; Durand, Michael; Margulis, Steve; England, Anthony

    2010-01-01

    Recent studies have begun exploring the assimilation of microwave radiances for the modeling and retrieval of snow properties. At a point scale, and for short durations (i week), radiance assimilation (RA) results are encouraging. However, in order to determine how practical RA might be for snow retrievals when applied over longer durations, larger spatial scales, and/or different snow types, we must expand the scope of the tests. In this paper we use coincident microwave radiance measurements and station data from a tundra site on the North Slope of Alaska. The field data are from the 3rd Radio-brightness Energy Balance Experiment (REBEX-3) carried out in 1994-95 by the University of Michigan. This dataset will provide a test of RA over months instead of one week, and for a very different type of snow than previous snow RA studies. We will address the following questions: flow well can a snowpack physical model (SM), forced with local weather, match measured conditions for a tundra snowpack?; How well can a microwave emission model, driven by the snowpack model, match measured microwave brightnesses for a tundra snowpack?; How well does RA increase or decrease the fidelity of estimates of snow depth and temperatures for a tundra snowpack?

  1. Atmospheric Emitted Radiance Interferometer (AERI) Handbook

    DOE Data Explorer

    Gero, Jonathan; Hackel, Denny; Garcia, Raymond

    2005-01-01

    The atmospheric emitted radiance interferometer (AERI) is a ground-based instrument that measures the downwelling infrared radiance from the Earth's atmosphere. The observations have broad spectral content and sufficient spectral resolution to discriminate among gaseous emitters (e.g., carbon dioxide and water vapor) and suspended matter (e.g., aerosols, water droplets, and ice crystals). These upward-looking surface observations can be used to obtain vertical profiles of tropospheric temperature and water vapor, as well as measurements of trace gases (e.g., ozone, carbon monoxide, and methane) and downwelling infrared spectral signatures of clouds and aerosols.The AERI is a passive remote sounding instrument, employing a Fourier transform spectrometer operating in the spectral range 3.3-19.2 μm (520-3020 cm-1) at an unapodized resolution of 0.5 cm-1 (max optical path difference of 1 cm). The extended-range AERI (ER-AERI) deployed in dry climates, like in Alaska, have a spectral range of 3.3-25.0 μm (400-3020 cm-1) that allow measurements in the far-infrared region. Typically, the AERI averages views of the sky over a 16-second interval and operates continuously.

  2. The proper weighting function for retrieving temperatures from satellite measured radiances

    NASA Technical Reports Server (NTRS)

    Arking, A.

    1976-01-01

    One class of methods for converting satellite measured radiances into atmospheric temperature profiles, involves a linearization of the radiative transfer equation: delta r = the sum of (W sub i) (delta T sub i) where (i=1...s) and where delta T sub i is the deviation of the temperature in layer i from that of a reference atmosphere, delta R is the difference in the radiance at satellite altitude from the corresponding radiance for the reference atmosphere, and W sub i is the discrete (or vector) form of the T-weighting (i.e., temperature weighting) function W(P), where P is pressure. The top layer of the atmosphere corresponds to i = 1, the bottom layer to i = s - 1, and i = s refers to the surface. Linearization in temperature (or some function of temperature) is at the heart of all linear or matrix methods. The weighting function that should be used is developed.

  3. A comparison of measured radiances from AIRS and HIRS across different cloud types

    NASA Astrophysics Data System (ADS)

    Schreier, M. M.; Kahn, B. H.; Staten, P.

    2015-12-01

    The observation of Earth's atmosphere with passive remote sensing instruments is ongoing for decades and resulting in a long-term global dataset. Two prominent examples are operational satellite platforms from the National Oceanic and Atmospheric Administration (NOAA) or research platforms like NASA's Earth Observing System (EOS). The observed spectral ranges of these observations are often similar among the different platforms, but have large differences when it comes to resolution, accuracy and quality control. Our approach is to combine different kinds of instruments at the pixel-scale to improve the characterization of infrared radiances. We focus on data from the High-resolution Infrared Radiation Sounder (HIRS) and compare the observations to radiances from the Atmospheric Infrared Sounder (AIRS) on Aqua. The high spectral resolution of AIRS is used to characterize and possibly recalibrate the observed radiances from HIRS. Our approach is unique in that we use additional information from other passive instruments on the same platforms including the Advanced Very High Resolution Radiometer (AVHRR) and the MODerate resolution Imaging Spectroradiometer (MODIS). We will present comparisons of radiances from HIRS and AIRS within different types of clouds that are determined from the imagers. In this way, we can analyze and select the most homogeneous conditions for radiance comparisons and a possible re-calibration of HIRS. We hope to achieve a cloud-type-dependent calibration and quality control for HIRS, which can be extrapolated into the past via inter-calibration of the different HIRS instruments beyond the time of AIRS.

  4. Effect of volume-scattering function on the errors induced when polarization is neglected in radiance calculations in an atmosphere-ocean system.

    PubMed

    Adams, C N; Kattawar, G W

    1993-08-20

    We have developed a Monte Carlo program that is capable of calculating both the scalar and the Stokes vector radiances in an atmosphere-ocean system in a single computer run. The correlated sampling technique is used to compute radiance distributions for both the scalar and the Stokes vector formulations simultaneously, thus permitting a direct comparison of the errors induced. We show the effect of the volume-scattering phase function on the errors in radiance calculations when one neglects polarization effects. The model used in this study assumes a conservative Rayleigh-scattering atmosphere above a flat ocean. Within the ocean, the volume-scattering function (the first element in the Mueller matrix) is varied according to both a Henyey-Greenstein phase function, with asymmetry factors G = 0.0, 0.5, and 0.9, and also to a Rayleigh-scattering phase function. The remainder of the reduced Mueller matrix for the ocean is taken to be that for Rayleigh scattering, which is consistent with ocean water measurement.

  5. Replacing effective spectral radiance by temperature in occupational exposure limits to protect against retinal thermal injury from light and near IR radiation.

    PubMed

    Madjidi, Faramarz; Behroozy, Ali

    2014-01-01

    Exposure to visible light and near infrared (NIR) radiation in the wavelength region of 380 to 1400 nm may cause thermal retinal injury. In this analysis, the effective spectral radiance of a hot source is replaced by its temperature in the exposure limit values in the region of 380-1400 nm. This article describes the development and implementation of a computer code to predict those temperatures, corresponding to the exposure limits proposed by the American Conference of Governmental Industrial Hygienists (ACGIH). Viewing duration and apparent diameter of the source were inputs for the computer code. At the first stage, an infinite series was created for calculation of spectral radiance by integration with Planck's law. At the second stage for calculation of effective spectral radiance, the initial terms of this infinite series were selected and integration was performed by multiplying these terms by a weighting factor R(λ) in the wavelength region 380-1400 nm. At the third stage, using a computer code, the source temperature that can emit the same effective spectral radiance was found. As a result, based only on measuring the source temperature and accounting for the exposure time and the apparent diameter of the source, it is possible to decide whether the exposure to visible and NIR in any 8-hr workday is permissible. The substitution of source temperature for effective spectral radiance provides a convenient way to evaluate exposure to visible light and NIR.

  6. Capability of MODIS radiance to analyze Iberian turbid plumes

    NASA Astrophysics Data System (ADS)

    Fernandez-Novoa, Diego; deCastro, Maite; Des, Marisela; Costoya, Xurxo; Mendes, Renato; Gomez-Gesteira, Moncho

    2017-04-01

    River plumes are formed near river mouths by freshwater and riverine materials. Therefore, the area influenced by freshwater (salinity plume) is usually negatively correlated with the area occupied by suspension and dissolved material (turbid plume). Suspended material results in a strong signal detected by satellite sensors whereas ocean clear waters have negligible contributions. Thus, remote sensing data, such as radiance obtained from Moderate Resolution Imaging Spectroradiometer (MODIS), are a very useful tool to analyze turbid plumes due to the high spatial and time resolution provided. Here, MODIS capability for characterizing similarities and differences among the most important Iberian plumes was assessed under the influence of their main forcing. Daily radiance data from MODIS-Aqua and MODIS-Terra satellite sensors were processed obtaining a resolution of 500 m. Two approaches are usually used for atmospheric correction treatments: Near-Infrared (NIR) bands and a combined algorithm using NIR and Short Wave Infrared (SWIR) bands. In the particular case of Iberian Peninsula plumes both methods offered similar results, although NIR bands present a lower associated error. MODIS allows working with several bands of normalized water-leaving radiances (nLw). Focusing in the resolution provided, nLw555 and 645 were the most appropriate because both provide the best coverage and correlation with river discharge. The nLw645 band was chosen because has a lower water penetration avoiding overestimations of turbidity caused by shallow seafloor areas and/or upwelling blooms. Daily data from both satellites were merged to enhance the robustness and precision of the study by increasing the number of available pixels. Results indicate that differences between radiance data from both satellites are negligible for Iberian plumes, justifying the merging. By last, each turbid limit, to delimit the respective plume from adjacent seawater, was obtained using two alternative

  7. Rayleigh radiance computations for satellite remote sensing: accounting for the effect of sensor spectral response function.

    PubMed

    Wang, Menghua

    2016-05-30

    To understand and assess the effect of the sensor spectral response function (SRF) on the accuracy of the top of the atmosphere (TOA) Rayleigh-scattering radiance computation, new TOA Rayleigh radiance lookup tables (LUTs) over global oceans and inland waters have been generated. The new Rayleigh LUTs include spectral coverage of 335-2555 nm, all possible solar-sensor geometries, and surface wind speeds of 0-30 m/s. Using the new Rayleigh LUTs, the sensor SRF effect on the accuracy of the TOA Rayleigh radiance computation has been evaluated for spectral bands of the Visible Infrared Imaging Radiometer Suite (VIIRS) on the Suomi National Polar-orbiting Partnership (SNPP) satellite and the Joint Polar Satellite System (JPSS)-1, showing some important uncertainties for VIIRS-SNPP particularly for large solar- and/or sensor-zenith angles as well as for large Rayleigh optical thicknesses (i.e., short wavelengths) and bands with broad spectral bandwidths. To accurately account for the sensor SRF effect, a new correction algorithm has been developed for VIIRS spectral bands, which improves the TOA Rayleigh radiance accuracy to ~0.01% even for the large solar-zenith angles of 70°-80°, compared with the error of ~0.7% without applying the correction for the VIIRS-SNPP 410 nm band. The same methodology that accounts for the sensor SRF effect on the Rayleigh radiance computation can be used for other satellite sensors. In addition, with the new Rayleigh LUTs, the effect of surface atmospheric pressure variation on the TOA Rayleigh radiance computation can be calculated precisely, and no specific atmospheric pressure correction algorithm is needed. There are some other important applications and advantages to using the new Rayleigh LUTs for satellite remote sensing, including an efficient and accurate TOA Rayleigh radiance computation for hyperspectral satellite remote sensing, detector-based TOA Rayleigh radiance computation, Rayleigh radiance calculations for high altitude

  8. Hyperspectral material identification on radiance data using single-atmosphere or multiple-atmosphere modeling

    NASA Astrophysics Data System (ADS)

    Mariano, Adrian V.; Grossmann, John M.

    2010-11-01

    Reflectance-domain methods convert hyperspectral data from radiance to reflectance using an atmospheric compensation model. Material detection and identification are performed by comparing the compensated data to target reflectance spectra. We introduce two radiance-domain approaches, Single atmosphere Adaptive Cosine Estimator (SACE) and Multiple atmosphere ACE (MACE) in which the target reflectance spectra are instead converted into sensor-reaching radiance using physics-based models. For SACE, known illumination and atmospheric conditions are incorporated in a single atmospheric model. For MACE the conditions are unknown so the algorithm uses many atmospheric models to cover the range of environmental variability, and it approximates the result using a subspace model. This approach is sometimes called the invariant method, and requires the choice of a subspace dimension for the model. We compare these two radiance-domain approaches to a Reflectance-domain ACE (RACE) approach on a HYDICE image featuring concealed materials. All three algorithms use the ACE detector, and all three techniques are able to detect most of the hidden materials in the imagery. For MACE we observe a strong dependence on the choice of the material subspace dimension. Increasing this value can lead to a decline in performance.

  9. Polarization impacts on the water-leaving radiance retrieval from above-water radiometric measurements.

    PubMed

    Harmel, Tristan; Gilerson, Alexander; Tonizzo, Alberto; Chowdhary, Jacek; Weidemann, Alan; Arnone, Robert; Ahmed, Sam

    2012-12-10

    Above-water measurements of water-leaving radiance are widely used for water-quality monitoring and ocean-color satellite data validation. Reflected skylight in above-water radiometry needs to be accurately estimated prior to derivation of water-leaving radiance. Up-to-date methods to estimate reflection of diffuse skylight on rough sea surfaces are based on radiative transfer simulations and sky radiance measurements. But these methods neglect the polarization state of the incident skylight, which is generally highly polarized. In this paper, the effects of polarization on the sea surface reflectance and the subsequent water-leaving radiance estimation are investigated. We show that knowledge of the polarization field of the diffuse skylight significantly improves above-water radiometry estimates, in particular in the blue part of the spectrum where the reflected skylight is dominant. A newly developed algorithm based on radiative transfer simulations including polarization is described. Its application to the standard Aerosol Robotic Network-Ocean Color and hyperspectral radiometric measurements of the 1.5-year dataset acquired at the Long Island Sound site demonstrates the noticeable importance of considering polarization for water-leaving radiance estimation. In particular it is shown, based on time series of collocated data acquired in coastal waters, that the azimuth range of measurements leading to good-quality data is significantly increased, and that these estimates are improved by more than 12% at 413 nm. Full consideration of polarization effects is expected to significantly improve the quality of the field data utilized for satellite data validation or potential vicarious calibration purposes.

  10. Influence of temperature fluctuations on infrared limb radiance: a new simulation code

    NASA Astrophysics Data System (ADS)

    Rialland, Valérie; Chervet, Patrick

    2006-08-01

    Airborne infrared limb-viewing detectors may be used as surveillance sensors in order to detect dim military targets. These systems' performances are limited by the inhomogeneous background in the sensor field of view which impacts strongly on target detection probability. This background clutter, which results from small-scale fluctuations of temperature, density or pressure must therefore be analyzed and modeled. Few existing codes are able to model atmospheric structures and their impact on limb-observed radiance. SAMM-2 (SHARC-4 and MODTRAN4 Merged), the Air Force Research Laboratory (AFRL) background radiance code can be used to in order to predict the radiance fluctuation as a result of a normalized temperature fluctuation, as a function of the line-of-sight. Various realizations of cluttered backgrounds can then be computed, based on these transfer functions and on a stochastic temperature field. The existing SIG (SHARC Image Generator) code was designed to compute the cluttered background which would be observed from a space-based sensor. Unfortunately, this code was not able to compute accurate scenes as seen by an airborne sensor especially for lines-of-sight close to the horizon. Recently, we developed a new code called BRUTE3D and adapted to our configuration. This approach is based on a method originally developed in the SIG model. This BRUTE3D code makes use of a three-dimensional grid of temperature fluctuations and of the SAMM-2 transfer functions to synthesize an image of radiance fluctuations according to sensor characteristics. This paper details the working principles of the code and presents some output results. The effects of the small-scale temperature fluctuations on infrared limb radiance as seen by an airborne sensor are highlighted.

  11. Snowpack modeling in the context of radiance assimilation for snow water equivalent mapping

    NASA Astrophysics Data System (ADS)

    Durand, M. T.; Kim, R. S.; Li, D.; Dumont, M.; Margulis, S. A.

    2017-12-01

    Data assimilation is often touted as a means of overcoming deficiences in both snowpack modeling and snowpack remote sensing. Direct assimilation of microwave radiances, rather than assimilating microwave retrievals, has shown promise, in this context. This is especially the case for deep mountain snow, which is often assumed to be infeasible to measure with microwave measurements, due to saturation issues. We first demonstrate that the typical way of understanding saturation has often been misunderstood. We show that deep snow leads to a complex microwave signature, but not to saturation per se, because of snowpack stratigraphy. This explains why radiance assimilation requires detailed snowpack models that adequatley stratgigraphy to function accurately. We examine this with two case studies. First, we show how the CROCUS predictions of snowpack stratigraphy allows for assimilation of airborne passive microwave measurements over three 1km2 CLPX Intensive Study Areas. Snowpack modeling and particle filter analysis is performed at 120 m spatial resolution. When run without the benefit of radiance assimilation, CROCUS does not fully capture spatial patterns in the data (R2=0.44; RMSE=26 cm). Assimlilation of microwave radiances for a single flight recovers the spatial pattern of snow depth (R2=0.85; RMSE = 13 cm). This is despite the presence of deep snow; measured depths range from 150 to 325 cm. Adequate results are obtained even for partial forest cover, and bias in precipitation forcing. The results are severely degraded if a three-layer snow model is used, however. The importance of modeling snowpack stratigraphy is highlighted. Second, we compare this study to a recent analysis assimilating spaceborne radiances for a 511 km2 sub-watershed of the Kern River, in the Sierra Nevada. Here, the daily Level 2A AMSR-E footprints (88 km2) are assimilated into a model running at 90 m spatial resolution. The three-layer model is specially adapted to predict "effective

  12. Factors affecting the estimate of primary production from space

    NASA Technical Reports Server (NTRS)

    Balch, W. M.; Byrne, C. F.

    1994-01-01

    Remote sensing of primary production in the euphotic zone has been based mostly on visible-band and water-leaving radiance measured with the coastal zone color scanner. There are some robust, simple relationships for calculating integral production based on surface measurements, but they also require knowledge for photoadaptive parameters such as maximum photosynthesis which currently cannot be obtained from spave. A 17,000-station data set is used to show that space-based estimates of maximum photosynthesis could improve predictions of psi, the water column light utiliztion index, which is an important term in many primary productivity models. Temperature is also examined as a factor for predicting hydrographic structure and primary production. A simple model is used to relate temperature and maximum photosynthesis; the model incorporates (1) the positive relationship between maximum photosynthesis and temperature and (2) the strongly negative relationship between temperature and nitrate in the ocean (which directly affects maximum growth rates via nitrogen limitation). Since these two factors relate to carbon and nitrogen, 'balanced carbon/nitrogen assimilation' was calculated using the Redfield ratio, It is expected that the relationship between maximum balanced carbon assimilation versus temperature is concave-down, with the peak dependent on nitrate uptake kinetics, temperature-nitrate relationships,a nd the carbon chlorophyll ration. These predictions were compared with the sea truth data. The minimum turnover time for nitrate was also calculated using this approach. Lastly, sea surface temperature gradients were used to predict the slope of isotherms (a proxy for the slope of isopycnals in many waters). Sea truth data show that at size scales of several hundred kilometers, surface temperature gradients can provide information on the slope of isotherms in the top 200 m of the water column. This is directly relevant to the supply of nutrients into the surface

  13. Neural network method to correct bidirectional effects in water-leaving radiance.

    PubMed

    Fan, Yongzhen; Li, Wei; Voss, Kenneth J; Gatebe, Charles K; Stamnes, Knut

    2016-01-01

    Ocean color algorithms that rely on "atmospherically corrected" nadir water-leaving radiances to infer information about marine constituents such as the chlorophyll concentration depend on a reliable method to convert the angle-dependent measured radiances from the observation direction to the nadir direction. It is also important to convert the measured radiances to the nadir direction when comparing and merging products from different satellite missions. The standard correction method developed by Morel and coworkers requires knowledge of the chlorophyll concentration. Also, the standard method was developed based on the Case 1 (open ocean) assumption, which makes it unsuitable for Case 2 situations such as turbid coastal waters. We introduce a neural network method to convert the angle-dependent water-leaving radiance (or the corresponding remote sensing reflectance) from the observation direction to the nadir direction. This method relies on neither an "atmospheric correction" nor prior knowledge of the water constituents or the inherent optical properties. It directly converts the remote sensing reflectance from an arbitrary slanted viewing direction to the nadir direction by using a trained neural network. This method is fast and accurate, and it can be easily adapted to different remote sensing instruments. Validation using NuRADS measurements in different types of water shows that this method is suitable for both Case 1 and Case 2 waters. In Case 1 or chlorophyll-dominated waters, our neural network method produces corrections similar to those of the standard method. In Case 2 waters, especially sediment-dominated waters, a significant improvement was obtained compared to the standard method.

  14. Pilot Comparison of Radiance Temperature Scale Realization Between NIMT and NMIJ

    NASA Astrophysics Data System (ADS)

    Keawprasert, T.; Yamada, Y.; Ishii, J.

    2015-03-01

    A pilot comparison of radiance temperature scale realizations between the National Institute of Metrology Thailand (NIMT) and the National Metrology Institute of Japan (NMIJ) was conducted. At the two national metrology institutes (NMIs), a 900 nm radiation thermometer, used as the transfer artifact, was calibrated by a means of a multiple fixed-point method using the fixed-point blackbody of Zn, Al, Ag, and Cu points, and by means of relative spectral responsivity measurements according to the International Temperature Scale of 1990 (ITS-90) definition. The Sakuma-Hattori equation is used for interpolating the radiance temperature scale between the four fixed points and also for extrapolating the ITS-90 temperature scale to 2000 C. This paper compares the calibration results in terms of fixed-point measurements, relative spectral responsivity, and finally the radiance temperature scale. Good agreement for the fixed-point measurements was found in case a correction for the change of the internal temperature of the artifact was applied using the temperature coefficient measured at the NMIJ. For the realized radiance temperature range from 400 C to 1100 C, the resulting scale differences between the two NMIs are well within the combined scale comparison uncertainty of 0.12 C (). The resulting spectral responsivity measured at the NIMT has a comparable curve to that measured at the NMIJ especially in the out-of-band region, yielding a ITS-90 scale difference within 1.0 C from the Cu point to 2000 C, whereas the realization comparison uncertainty of NIMT and NMIJ combined is 1.2 C () at 2000 C.

  15. A Study of Global Cirrus Cloud Morphology with AIRS Cloud-clear Radiances (CCRs)

    NASA Technical Reports Server (NTRS)

    Wu, Dong L.; Gong, Jie

    2012-01-01

    Version 6 (V6) AIRS cloud-clear radiances (CCR) are used to derive cloud-induced radiance (Tcir=Tb-CCR) at the infrared frequencies of weighting functions peaked in the middle troposphere. The significantly improved V 6 CCR product allows a more accurate estimation of the expected clear-sky radiance as if clouds are absent. In the case where strong cloud scattering is present, the CCR becomes unreliable, which is reflected by its estimated uncertainty, and interpolation is employed to replace this CCR value. We find that Tcir derived from this CCR method are much better than other methods and detect more clouds in the upper and lower troposphere as well as in the polar regions where cloud detection is particularly challenging. The cloud morphology derived from the V6 test month, as well as some artifacts, will be shown.

  16. Upwelling Radiance at 976 nm Measured from Space Using a CCD Camera

    NASA Technical Reports Server (NTRS)

    Biswas, Abhijit; Kovalik, Joseph M.; Oaida, Bogdan V.; Abrahamson, Matthew J.; Wright, Malcolm W.

    2015-01-01

    The Optical Payload for Lasercomm Science (OPALS) Flight System on-board the International Space Station uses a charge coupled device (CCD) camera for receiving a beacon laser from Earth. Relative measurements of the background contributed by upwelling radiance under diverse illumination conditions and varying terrain is presented. In some cases clouds in the field-of-view allowed a comparison of terrestrial and cloud-top upwelling radiance. In this paper we will report these measurements and examine the extent of agreement with atmospheric model predictions.

  17. Measured and Modeled Downwelling Far-Infrared Radiances in Very Dry Environments and Calibration Requirements for Future Experiments

    NASA Astrophysics Data System (ADS)

    Mast, J. C.; Mlynczak, M. G.; Cageao, R.; Kratz, D. P.; Latvakoski, H.; Johnson, D. G.; Mlawer, E. J.; Turner, D. D.

    2016-12-01

    Downwelling radiances measured by the Far-Infrared Spectroscopy of the Troposphere (FIRST) instrument in an environment with integrated precipitable water as low as 0.03 cm are compared with calculated spectra in the far-infrared and mid-infrared. In its current ground-based configuration FIRST was deployed to 5.38 km on Cerro Toco, a mountain in the Atacama Desert of Chile, from August to October 2009. There FIRST took part in the Radiative Heating in Unexplored Bands Campaign Part 2. Water vapor and temperature profiles from an optimal-estimation-based physical retrieval algorithm (using simultaneous radiosonde and multichannel 183 GHz microwave radiometer measurements) are input to the AER Line-by-Line Radiative Transfer Model (LBLRTM) to compute radiances for comparison with FIRST. The AER v3.4 line parameter database is used. The low water vapor amounts and relatively cold atmosphere result in extremely small far-IR radiances (1.5 mW/m2/sr/cm-1) with corresponding brightness temperatures of 120 K. The residual LBLRTM minus FIRST is calculated to assess agreement between the measured and modeled spectra. Uncertainties in both the measured and modeled radiances are accounted for in the comparison. A goal of the deployment and subsequent analysis is the assessment of water vapor spectroscopy in the far-infrared and mid-infrared. While agreement is found between measured and modeled radiances within the combined uncertainties across all spectra, uncertainties in the measured water vapor profiles and from the laboratory calibration exceed those associated with water vapor spectroscopy in this very low radiance environment. Consequently, no improvement in water vapor spectroscopy is afforded by these measurements. However, we use these results to place requirements on instrument calibration accuracy and water vapor profile accuracy for future campaigns to similarly dry environments. Instrument calibration uncertainty needs to be at 2% (1-sigma) of measured radiance

  18. Assessment of the first radiances received from the VSSR Atmospheric Sounder (VAS) instrument

    NASA Technical Reports Server (NTRS)

    Chesters, D.; Uccellini, L. W.; Montgomery, H.; Mostek, A.; Robinson, W.

    1981-01-01

    The first orderly, calibrated radiances from the VAS-D instrument on the GOES-4 satellite are examined for: image quality, radiometric precision, radiation transfer verification at clear air radiosonde sites, regression retrieval accuracy, and mesoscale analysis features. Postlaunch problems involving calibration and data processing irregularities of scientific or operational significance are included. The radiances provide good visual and relative radiometric data for empirically conditioned retrievals of mesoscale temperature and moisture fields in clear air.

  19. Remote Sensing of Cloud Properties using Ground-based Measurements of Zenith Radiance

    NASA Technical Reports Server (NTRS)

    Chiu, J. Christine; Marshak, Alexander; Knyazikhin, Yuri; Wiscombe, Warren J.; Barker, Howard W.; Barnard, James C.; Luo, Yi

    2006-01-01

    An extensive verification of cloud property retrievals has been conducted for two algorithms using zenith radiances measured by the Atmospheric Radiation Measurement (ARM) Program ground-based passive two-channel (673 and 870 nm) Narrow Field-Of-View Radiometer. The underlying principle of these algorithms is that clouds have nearly identical optical properties at these wavelengths, but corresponding spectral surface reflectances (for vegetated surfaces) differ significantly. The first algorithm, the RED vs. NIR, works for a fully three-dimensional cloud situation. It retrieves not only cloud optical depth, but also an effective radiative cloud fraction. Importantly, due to one-second time resolution of radiance measurements, we are able, for the first time, to capture detailed changes in cloud structure at the natural time scale of cloud evolution. The cloud optical depths tau retrieved by this algorithm are comparable to those inferred from both downward fluxes in overcast situations and microwave brightness temperatures for broken clouds. Moreover, it can retrieve tau for thin patchy clouds, where flux and microwave observations fail to detect them. The second algorithm, referred to as COUPLED, couples zenith radiances with simultaneous fluxes to infer 2. In general, the COUPLED and RED vs. NIR algorithms retrieve consistent values of tau. However, the COUPLED algorithm is more sensitive to the accuracies of measured radiance, flux, and surface reflectance than the RED vs. NIR algorithm. This is especially true for thick overcast clouds where it may substantially overestimate z.

  20. Use of near infrared/red radiance ratios for estimating vegetation biomass and physiological status

    NASA Technical Reports Server (NTRS)

    Tucker, C. J.

    1977-01-01

    The application of photographic infrared/red (ir/red) reflectance or radiance ratios for the estimation of vegetation biomass and physiological status were investigated by analyzing in situ spectral reflectance data from experimental grass plots. Canopy biological samples were taken for total wet biomass, total dry biomass, leaf water content, dry green biomass, dry brown biomass, and total chlorophyll content at each sampling date. Integrated red and photographic infrared radiances were regressed against the various canopy or plot variables to determine the relative significance between the red, photographic infrared, and the ir/red ratio and the canopy variables. The ir/red ratio is sensitive to the photosynthetically active or green biomass, the rate of primary production, and actually measures the interaction between the green biomass and the rate of primary production within a given species type. The ir/red ratio resulted in improved regression significance over the red or the ir/radiances taken separately. Only slight differences were found between ir/red ratio, the ir-red difference, the vegetation index, and the transformed vegetation index. The asymptotic spectral radiance properties of the ir, red, ir/red ratio, and the various transformations were evaluated.

  1. CrIS High Resolution Hyperspectral Radiances

    NASA Astrophysics Data System (ADS)

    Hepplewhite, C. L.; Strow, L. L.; Motteler, H.; Desouza-Machado, S. G.; Tobin, D. C.; Martin, G.; Gumley, L.

    2014-12-01

    The CrIS hyperspectral sounder flying on Suomi-NPPpresently has reduced spectral resolution in the mid-wave andshort-wave spectral bands due to truncation of the interferograms inorbit. CrIS has occasionally downlinked full interferograms for thesebands (0.8 cm max path, or 0.625 cm-1 point spacing) for a feworbits up to a full day. Starting Oct.1, 2014 CrIS will be commandedto download full interferograms continuously for the remainder of themission, although NOAA will not immediately produce high-spectralresolution Sensor Data Records (SDRs). Although the originalmotivation for operating in high-resolution mode was improved spectralcalibration, these new data will also improve (1) vertical sensitivityto water vapor, and (2) greatly increase the CrIS sensitivity tocarbon monoxide. This should improve (1) NWP data assimilation ofwater vapor and (2) provide long-term continuity of carbon monoxideretrievals begun with MOPITT on EOS-TERRA and AIRS on EOS-AQUA. Wehave developed a SDR algorithm to produce calibrated high-spectralresolution radiances which includes several improvements to theexisting CrIS SDR algorithm, and will present validation of thesehigh-spectral resolution radiances using a variety of techniques,including bias evaluation versus NWP model data and inter-comparisonsto AIRS and IASI using simultaneous nadir overpasses (SNOs). Theauthors are presently working to implement this algorithm for NASASuomi NPP Program production of Earth System Data Records.

  2. The angular distribution of infrared radiances emerging from broken fields of cumulus clouds

    NASA Technical Reports Server (NTRS)

    Naber, P. S.; Weinman, J. A.

    1984-01-01

    Infrared radiances were simultaneously measured from broken cloud fields over the eastern Pacific Ocean by means of the eastern and western geostationary satellites. The measurements were compared with the results of models that characterized the clouds as black circular cylinders disposed randomly on a plane and as black cuboids disposed in regular and in shifted periodic arrays. The data were also compared with the results obtained from a radiative transfer model that considered emission and scattering by a regular array of periodic cuboidal clouds. It was found that the radiances did not depend significantly on the azimuth angle; this suggested that the observed cloud fields were not regular periodic arrays. However, the dependence on zenith angle suggested that the clouds were not disposed randomly either. The implication of these measurements on the understanding of the transfer of infrared radiances through broken cloud fields is considered.

  3. Joint aerosol and water-leaving radiance retrieval from Airborne Multi-angle SpectroPolarimeter Imager

    NASA Astrophysics Data System (ADS)

    Xu, F.; Dubovik, O.; Zhai, P.; Kalashnikova, O. V.; Diner, D. J.

    2015-12-01

    The Airborne Multiangle SpectroPolarimetric Imager (AirMSPI) [1] has been flying aboard the NASA ER-2 high altitude aircraft since October 2010. In step-and-stare operation mode, AirMSPI typically acquires observations of a target area at 9 view angles between ±67° off the nadir. Its spectral channels are centered at 355, 380, 445, 470*, 555, 660*, and 865* nm, where the asterisk denotes the polarimetric bands. In order to retrieve information from the AirMSPI observations, we developed a efficient and flexible retrieval code that can jointly retrieve aerosol and water leaving radiance simultaneously. The forward model employs a coupled Markov Chain (MC) [2] and adding/doubling [3] radiative transfer method which is fully linearized and integrated with a multi-patch retrieval algorithm to obtain aerosol and water leaving radiance/Chl-a information. Various constraints are imposed to improve convergence and retrieval stability. We tested the aerosol and water leaving radiance retrievals using the AirMSPI radiance and polarization measurements by comparing to the retrieved aerosol concentration, size distribution, water-leaving radiance, and chlorophyll concentration to the values reported by the USC SeaPRISM AERONET-OC site off the coast of Southern California. In addition, the MC-based retrievals of aerosol properties were compared with GRASP ([4-5]) retrievals for selected cases. The MC-based retrieval approach was then used to systematically explore the benefits of AirMSPI's ultraviolet and polarimetric channels, the use of multiple view angles, and constraints provided by inclusion of bio-optical models of the water-leaving radiance. References [1]. D. J. Diner, et al. Atmos. Meas. Tech. 6, 1717 (2013). [2]. F. Xu et al. Opt. Lett. 36, 2083 (2011). [3]. J. E. Hansen and L.D. Travis. Space Sci. Rev. 16, 527 (1974). [4]. O. Dubovik et al. Atmos. Meas. Tech., 4, 975 (2011). [5]. O. Dubovik et al. SPIE: Newsroom, DOI:10.1117/2.1201408.005558 (2014).

  4. Spectral reflectance and radiance characteristics of water pollutants

    NASA Technical Reports Server (NTRS)

    Wezernak, C. T.; Turner, R. E.; Lyzenga, D. R.

    1976-01-01

    Spectral reflectance characteristics of water pollutants and water bodies were compiled using the existing literature. Radiance calculations were performed at satellite altitude for selected illumination angles and atmospheric conditions. The work described in this report was limited to the reflective portion of the spectrum between 0.40 micrometer to 1.0 micrometer.

  5. Estimating top-of-atmosphere thermal infrared radiance using MERRA-2 atmospheric data

    NASA Astrophysics Data System (ADS)

    Kleynhans, Tania; Montanaro, Matthew; Gerace, Aaron; Kanan, Christopher

    2017-05-01

    Thermal infrared satellite images have been widely used in environmental studies. However, satellites have limited temporal resolution, e.g., 16 day Landsat or 1 to 2 day Terra MODIS. This paper investigates the use of the Modern-Era Retrospective analysis for Research and Applications, Version 2 (MERRA-2) reanalysis data product, produced by NASA's Global Modeling and Assimilation Office (GMAO) to predict global topof-atmosphere (TOA) thermal infrared radiance. The high temporal resolution of the MERRA-2 data product presents opportunities for novel research and applications. Various methods were applied to estimate TOA radiance from MERRA-2 variables namely (1) a parameterized physics based method, (2) Linear regression models and (3) non-linear Support Vector Regression. Model prediction accuracy was evaluated using temporally and spatially coincident Moderate Resolution Imaging Spectroradiometer (MODIS) thermal infrared data as reference data. This research found that Support Vector Regression with a radial basis function kernel produced the lowest error rates. Sources of errors are discussed and defined. Further research is currently being conducted to train deep learning models to predict TOA thermal radiance

  6. BBAERI vs. BNAERI: A Comparison of Two Hyperspectral Atmospheric Downwelling Radiance Interferometers

    NASA Astrophysics Data System (ADS)

    Wilson, R.; McMillan, W.; Shaw, J.

    2006-12-01

    Simultaneous measurements of atmospheric downwelling infrared radiances have been measured at UMBC's Atmospheric Remote sensing Facility (ARF). We present BBAERI and BNAERI spectral comparisons to demonstrate their consistent radiometric calibration and will show examples of retrieval products from each. The atmospheric emitted radiances were measured using two different Atmospheric Emitted Radiance Interferometers' (AERI): the Baltimore Bomem AERI (BBAERI) entirely built by ABB Bomem and the Baltimore NOAA AERI (BNAERI) assembled by research scientists at NOAA. BBAERI previously has been used for field experiments in support of satellite validation, but now will spend most of its time at UMBC. BNAERI was designed for autonomous field operations. Planned upcoming field campaigns for BNAERI include experiments in central Alaska or in the Baltimore-Washington area. AERI devices were originally designed by the University of Madison Wisconsin to retrieve temperature and water vapor profiles up to the boundary layer every eight to ten minutes. In addition to boundary layer temperature and water vapor profiling, we will report retrieved boundary layer abundances of trace gases.

  7. Evaluation of the Impact of AIRS Radiance and Profile Data Assimilation in Partly Cloudy Regions

    NASA Technical Reports Server (NTRS)

    Zavodsky, Bradley; Srikishen, Jayanthi; Jedlovec, Gary

    2013-01-01

    Improvements to global and regional numerical weather prediction have been demonstrated through assimilation of data from NASA s Atmospheric Infrared Sounder (AIRS). Current operational data assimilation systems use AIRS radiances, but impact on regional forecasts has been much smaller than for global forecasts. Retrieved profiles from AIRS contain much of the information that is contained in the radiances and may be able to reveal reasons for this reduced impact. Assimilating AIRS retrieved profiles in an identical analysis configuration to the radiances, tracking the quantity and quality of the assimilated data in each technique, and examining analysis increments and forecast impact from each data type can yield clues as to the reasons for the reduced impact. By doing this with regional scale models individual synoptic features (and the impact of AIRS on these features) can be more easily tracked. This project examines the assimilation of hyperspectral sounder data used in operational numerical weather prediction by comparing operational techniques used for AIRS radiances and research techniques used for AIRS retrieved profiles. Parallel versions of a configuration of the Weather Research and Forecasting (WRF) model with Gridpoint Statistical Interpolation (GSI) are run to examine the impact AIRS radiances and retrieved profiles. Statistical evaluation of a long-term series of forecast runs will be compared along with preliminary results of in-depth investigations for select case comparing the analysis increments in partly cloudy regions and short-term forecast impacts.

  8. A Novel Method of Measuring Upwelling Radiance in the Hydrographic Sub-Hull

    NASA Astrophysics Data System (ADS)

    Rüssmeier, N.; Zielinski, O.

    2016-01-01

    In this study we present a new method useful in collecting upwelling radiance (Lu) from a platform submerged in a hydrographic sub-hull or moon pool of a research vessel. The information analyzed here was obtained during a field campaign in the Northwestern European shelf seas aboard the new research vessel SONNE. As the platform was located at the center of the ship, there is minimal effect from pitch and roll which is known to influence upwelling radiance observations. A comparison of the measurements from this platform with a free falling hyperspectral profiler was performed to determine the degree of uncertainty that results from ship shadow. For given Lu(λ) in situ data we observed ±33% intensity deviations compared to profiling measurements that can be attributed to instrument shading during moon pool installation and environmental perturbations. Furthermore Lu(λ) in situ spectra variations were observed at lower wavelengths, therefore a form fitting algorithm was adapted to receive corresponding depths with identical spectral form from Lu(z, λ) profiler casts. During an east to west transect in North Sea with a schedule speed up to 12 knots in situ radiance reflectance rrs(7, λ) measurements at 7 meter depth were performed with this novel radiometer setup. In spite of any restrictions originating from the sub-hull installation, water masses mixing zone from CDOM dominated coastal waters in the Skagerrak Strait towards the open North Sea were successfully derived thus offering an underway applicable upwelling radiance sensing not suffering from sun glint or other typical restrictions of above water radiometer installations.

  9. Cross Calibration of TOMS, SBUV/2 and SCIAMACHY Radiances from Ground Observations

    NASA Technical Reports Server (NTRS)

    Hilsenrath, Ernest; Bhartia, P. K.; Bojkov, B.; Kowaleski, M.; Labow, G.; Ahmad, Z.

    2002-01-01

    We have shown that validation of radiances is a very effective means for correcting absolute accuracy and long term drifts of backscatter type satellite measurements. This method by-passes the algorithms used for both satellite and ground based measurements which are normally used to validate and correct the satellite data. A new method for satellite validation is planned which will compliment measurements from the existing ground-based networks. This method will employ very accurate comparisons between ground based zenith sky radiances and satellite nadir radiances. These comparisons will rely heavily on the experience derived from the Shuttle SBUV (SSBUV) program which provided a reference standard of radiance measurements for SBUV/2, TOMS, and GOME. This new measurement program, called 'Skyrad', employs two well established capabilities at the Goddard Space Flight Center, 1) the SSBUV calibration facilities and 2) the radiative transfer codes used for the TOMS and SBUV/2 algorithms and their subsequent refinements. Radiative transfer calculations show that ground based zenith sky and satellite nadir backscatter ultraviolet comparisons can be made very accurately under certain viewing conditions. The Skyrad instruments (SSBUV, Brewer spectrophotometers, and possibly others) will be calibrated and maintained to a precision of a few tenths of a percent. Skyrad data will then enable long term calibration of upcoming satellite instruments such as QuickTOMS, SBUV/2s and SCIAMACHY with a high degree of precision. This technique can be further employed to monitor the performance of future instruments such as GOMEZ, OMI, and OMPS. Additional information is included in the original extended abstract.

  10. Using sky radiances measured by ground based AERONET Sun-Radiometers for cirrus cloud detection

    NASA Astrophysics Data System (ADS)

    Sinyuk, A.; Holben, B. N.; Eck, T. F.; Slutsker, I.; Lewis, J. R.

    2013-12-01

    Screening of cirrus clouds using observations of optical depth (OD) only has proven to be a difficult task due mostly to some clouds having temporally and spatially stable OD. On the other hand, the sky radiances measurements which in AERONET protocol are taken throughout the day may contain additional cloud information. In this work the potential of using sky radiances for cirrus cloud detection is investigated. The detection is based on differences in the angular shape of sky radiances due to cirrus clouds and aerosol (see Figure). The range of scattering angles from 3 to 6 degrees was selected due to two primary reasons: high sensitivity to cirrus clouds presence, and close proximity to the Sun. The angular shape of sky radiances was parametrized by its curvature, which is a parameter defined as a combination of the first and second derivatives as a function of scattering angle. We demonstrate that a slope of the logarithm of curvature versus logarithm of scattering angle in this selected range of scattering angles is sensitive to cirrus cloud presence. We also demonstrate that restricting the values of the slope below some threshold value can be used for cirrus cloud screening. The threshold value of the slope was estimated using collocated measurements of AERONET data and MPLNET lidars.

  11. Spectral radiance measurements and calculated soot concentrations along the length of an experimental combustor

    NASA Technical Reports Server (NTRS)

    Norgren, C. T.; Ingebo, R. D.

    1976-01-01

    Radiometric data were obtained over a range of parametric test conditions at three positions along the length of an experimental combustor segment corresponding to the primary, intermediate, and dilution zones. The concentration of soot entrained in the combustion gases was calculated by a technique using spectral radiance measurements. Tests were conducted primarily with Jet A fuel, although limited data were taken with two fuels having higher aromatic content, diesel oil number 2 and a blend of 40 percent tetralin in Jet A fuel. Radiometric observation of the combustion gases indicated that the maximum total radiance peaked at the intermediate zone, which was located immediately upstream of the dilution holes. Soot concentrations calculated from optical measurements in the dilution zone compared favorably with those obtained by in situ gas sampling at the exhaust. The total radiance increased with the higher aromatic content fuels.

  12. Use of simulated satellite radiances from a mesoscale numerical model to understand kinematic and dynamic processes

    NASA Technical Reports Server (NTRS)

    Kalb, Michael; Robertson, Franklin; Jedlovec, Gary; Perkey, Donald

    1987-01-01

    Techniques by which mesoscale numerical weather prediction model output and radiative transfer codes are combined to simulate the radiance fields that a given passive temperature/moisture satellite sensor would see if viewing the evolving model atmosphere are introduced. The goals are to diagnose the dynamical atmospheric processes responsible for recurring patterns in observed satellite radiance fields, and to develop techniques to anticipate the ability of satellite sensor systems to depict atmospheric structures and provide information useful for numerical weather prediction (NWP). The concept of linking radiative transfer and dynamical NWP codes is demonstrated with time sequences of simulated radiance imagery in the 24 TIROS vertical sounder channels derived from model integrations for March 6, 1982.

  13. Bidirectional reflectance of oceanic waters: A comparison of modeled and measured upward radiance fields

    NASA Technical Reports Server (NTRS)

    Morel, Andre; Voss, Kenneth J.; Gentili, Bernard

    1995-01-01

    The bidirectional reflectance of oceanic waters is conveniently described in a normalized way by forming the ratio of the upwelling irradiance E(sub u) to any upwelling radiance L(sub u)(theta prime, phi). This ratio, Q (theta prime, theta(sub 0), (phi(sub 0) - phi), where theta prime, phi are the nadir and azimuth angles for the upward radiance and theta(sub 0), phi(sub 0) are the zenith and azimuth angles of the Sun, has been determined from measurements at sea and computed via Monte Carlo simulations using the inherent optical properties measured in the field and appropriate boundary conditions (clear sky, no wind, varying Sun angle). Experimental ad computed Q values are in excellent agreement. This successful comparison confirms the importance of the bidirectional character of ocean reflectance, already pointed out from a purely numerical approach without field validation, and corroborates the extended range of the Q variations. The later point is of importance when interpreting the marine signals detected by an ocean color satellite-borne sensor. The validation is extended by considering the historical data for the radiance distributions in Lake Pend Oreille determined at various depths. The closure issue in ocean optics is examined by solving the direct problem of radiative transfer and through a model-data comparison in terms of radiance field.

  14. Factors affecting sign retroreflectivity

    DOT National Transportation Integrated Search

    2001-01-01

    This study was undertaken to better understand the factors that may affect road sign retroreflectivity, specifically age and physical orientation. A better understanding of these factors could provide guidance to ODOT in managing its inventory of roa...

  15. Impact of horizontal and vertical localization scales on microwave sounder SAPHIR radiance assimilation

    NASA Astrophysics Data System (ADS)

    Krishnamoorthy, C.; Balaji, C.

    2016-05-01

    In the present study, the effect of horizontal and vertical localization scales on the assimilation of direct SAPHIR radiances is studied. An Artificial Neural Network (ANN) has been used as a surrogate for the forward radiative calculations. The training input dataset for ANN consists of vertical layers of atmospheric pressure, temperature, relative humidity and other hydrometeor profiles with 6 channel Brightness Temperatures (BTs) as output. The best neural network architecture has been arrived at, by a neuron independence study. Since vertical localization of radiance data requires weighting functions, a ANN has been trained for this purpose. The radiances were ingested into the NWP using the Ensemble Kalman Filter (EnKF) technique. The horizontal localization has been taken care of, by using a Gaussian localization function centered around the observed coordinates. Similarly, the vertical localization is accomplished by assuming a function which depends on the weighting function of the channel to be assimilated. The effect of both horizontal and vertical localizations has been studied in terms of ensemble spread in the precipitation. Aditionally, improvements in 24 hr forecast from assimilation are also reported.

  16. An Investigation of the Characterization of Cloud Contamination in Hyperspectral Radiances

    NASA Technical Reports Server (NTRS)

    McCarty, William; Jedlovec, Gary J.; LeMarshall, John

    2007-01-01

    In regions lacking direct observations, the assimilation of radiances from infrared and microwave sounders is the primary method for characterizing the atmosphere in the analysis process. In recent years, technological advances have led to the launching of more advanced sounders, particularly in the thermal infrared spectrum. With the advent of these hyperspectral sounders, the amount of data available for the analysis process has and will continue to be dramatically increased. However, the utilization of infrared radiances in variational assimilation can be problematic in the presence of clouds; specifically the assessment of the presence of clouds in an instantaneous field of view (IFOV) and the contamination in the individual channels within the IFOV. Various techniques have been developed to determine if a channel is contaminated by clouds. The work presented in this paper and subsequent presentation will investigate traditional techniques and compare them to a new technique, the C02 sorting technique, which utilizes the high spectral resolution of the Atmospheric Infrared Sounder (AIRS) within the framework of the Gridpoint Statistical Interpolation (GSI) 3DVAR system. Ultimately, this work is done in preparation for the assessment of short-term forecast impacts with the regional assimilation of AIRS radiances within the analysis fields of the Weather Research and Forecast Nonhydrostatic Mesoscale Model (WRF-NMM) at the NASA Short-term Prediction Research and Transition (SPORT) Center.

  17. Assimilation of SBUV Version 8 Radiances into the GEOS Ozone DAS

    NASA Technical Reports Server (NTRS)

    Mueller, Martin D.; Stajner, Ivanka; Bhartia, Pawan K.

    2004-01-01

    In operational weather forecasting, the assimilation of brightness temperatures from satellite sounders, instead of assimilation of 1D-retrievals has become increasingly common practice over the last two decades. Compared to these systems, assimilation of trace gases is still at a relatively early stage of development, and efforts to directly assimilate radiances instead of retrieved products have just begun a few years ago, partially because it requires much more computation power due to the employment of a radiative transport forward model (FM). This paper will focus on a method to assimilate SBUV/2 radiances (albedos) into the Global Earth Observation System Ozone Data Assimilation Scheme (GEOS-03DAS). While SBUV-type instruments cannot compete with newer sensors in terms of spectral and horizontal resolution, they feature a continuous data record back to 1978, which makes them very valuable for trend studies. Assimilation can help spreading their ground coverage over the whole globe, as has been previously demonstrated with the GEOS-03DAS using SBUV Version 6 ozone profiles. Now, the DAS has been updated to use the newly released SBUV Version 8 data. We will compare pre]lmlnarv results of SBUV radiance assimilation with the assimilation of retrieved ozone profiles, discuss methods to deal with the increased computational load, and try to assess the error characteristics and future potential of the new approach.

  18. Normalization and calibration of geostationary satellite radiances for the International Satellite Cloud Climatology Project

    NASA Technical Reports Server (NTRS)

    Desormeaux, Yves; Rossow, William B.; Brest, Christopher L.; Campbell, G. G.

    1993-01-01

    Procedures are described for normalizing the radiometric calibration of image radiances obtained from geostationary weather satellites that contributed data to the International Satellite Cloud Climatology Project. The key step is comparison of coincident and collocated measurements made by each satellite and the concurrent AVHRR on the 'afternoon' NOAA polar-orbiting weather satellite at the same viewing geometry. The results of this comparison allow transfer of the AVHRR absolute calibration, which has been established over the whole series, to the radiometers on the geostationary satellites. Results are given for Meteosat-2, 3, and 4, for GOES-5, 6, and 7, for GMS-2, 3, and 4 and for Insat-1B. The relative stability of the calibrations of these radiance data is estimated to be within +/- 3 percent; the uncertainty of the absolute calibrations is estimated to be less than 10 percent. The remaining uncertainties are at least two times smaller than for the original radiance data.

  19. High temperature radiance spectroscopy measurements of solid and liquid uranium and plutonium carbides

    NASA Astrophysics Data System (ADS)

    Manara, D.; De Bruycker, F.; Boboridis, K.; Tougait, O.; Eloirdi, R.; Malki, M.

    2012-07-01

    In this work, an experimental study of the radiance of liquid and solid uranium and plutonium carbides at wavelengths 550 nm ⩽ λ ⩽ 920 nm is reported. A fast multi-channel spectro-pyrometer has been employed for the radiance measurements of samples heated up to and beyond their melting point by laser irradiation. The melting temperature of uranium monocarbide, soundly established at 2780 K, has been taken as a radiance reference. Based on it, a wavelength-dependence has been obtained for the high-temperature spectral emissivity of some uranium carbides (1 ⩽ C/U ⩽ 2). Similarly, the peritectic temperature of plutonium monocarbide (1900 K) has been used as a reference for plutonium monocarbide and sesquicarbide. The present spectral emissivities of solid uranium and plutonium carbides are close to 0.5 at 650 nm, in agreement with previous literature values. However, their high temperature behaviour, values in the liquid, and carbon-content and wavelength dependencies in the visible-near infrared range have been determined here for the first time. Liquid uranium carbide seems to interact with electromagnetic radiation in a more metallic way than does the solid, whereas a similar effect has not been observed for plutonium carbides. The current emissivity values have also been used to convert the measured radiance spectra into real temperature, and thus perform a thermal analysis of the laser heated samples. Some high-temperature phase boundaries in the systems U-C and Pu-C are shortly discussed on the basis of the current results.

  20. Radiance Research Particle Soot/Absorption Photometer Instrument Handbook

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Springston, S. R.

    2016-03-01

    Radiance Research PSAPs as described in this Handbook are deployed in the second ARM Mobile Facility (AMF2) Aerosol Observing System (AOS), the third ARM Mobile Facility (AMF3) AOS, ENA AOS and Mobile Aerosol Observing System (MAOS)-A. An earlier version of the PSAP is currently operated in the ARM Aerial Facility and at SGP. The older SGP instrument is covered in a separate Handbook.

  1. Multi-sensor Cloud Retrieval Simulator and Remote Sensing from Model Parameters . Pt. 1; Synthetic Sensor Radiance Formulation; [Synthetic Sensor Radiance Formulation

    NASA Technical Reports Server (NTRS)

    Wind, G.; DaSilva, A. M.; Norris, P. M.; Platnick, S.

    2013-01-01

    In this paper we describe a general procedure for calculating synthetic sensor radiances from variable output from a global atmospheric forecast model. In order to take proper account of the discrepancies between model resolution and sensor footprint, the algorithm takes explicit account of the model subgrid variability, in particular its description of the probability density function of total water (vapor and cloud condensate.) The simulated sensor radiances are then substituted into an operational remote sensing algorithm processing chain to produce a variety of remote sensing products that would normally be produced from actual sensor output. This output can then be used for a wide variety of purposes such as model parameter verification, remote sensing algorithm validation, testing of new retrieval methods and future sensor studies.We show a specific implementation using the GEOS-5 model, the MODIS instrument and the MODIS Adaptive Processing System (MODAPS) Data Collection 5.1 operational remote sensing cloud algorithm processing chain (including the cloud mask, cloud top properties and cloud optical and microphysical properties products). We focus on clouds because they are very important to model development and improvement.

  2. Physical Retrieval of Surface Emissivity Spectrum from Hyperspectral Infrared Radiances

    NASA Technical Reports Server (NTRS)

    Li, Jun; Weisz, Elisabeth; Zhou, Daniel K.

    2007-01-01

    Retrieval of temperature, moisture profiles and surface skin temperature from hyperspectral infrared (IR) radiances requires spectral information about the surface emissivity. Using constant or inaccurate surface emissivities typically results in large retrieval errors, particularly over semi-arid or arid areas where the variation in emissivity spectrum is large both spectrally and spatially. In this study, a physically based algorithm has been developed to retrieve a hyperspectral IR emissivity spectrum simultaneously with the temperature and moisture profiles, as well as the surface skin temperature. To make the solution stable and efficient, the hyperspectral emissivity spectrum is represented by eigenvectors, derived from the laboratory measured hyperspectral emissivity database, in the retrieval process. Experience with AIRS (Atmospheric InfraRed Sounder) radiances shows that a simultaneous retrieval of the emissivity spectrum and the sounding improves the surface skin temperature as well as temperature and moisture profiles, particularly in the near surface layer.

  3. Active fire detection using a peat fire radiance model

    NASA Astrophysics Data System (ADS)

    Kushida, K.; Honma, T.; Kaku, K.; Fukuda, M.

    2011-12-01

    The fire fractional area and radiances at 4 and 11 μm of active fires in Indonesia were estimated using Advanced Spaceborne Thermal Emission and Reflection Radiometer (ASTER) images. Based on these fire information, a stochastic fire model was used for evaluating two fire detection algorithms of Moderate Resolution Imaging Spectroradiometer (MODIS). One is single-image stochastic fire detection, and the other is multitemporal stochastic fire detection (Kushida, 2010 - IEEE Geosci. Remote Sens. Lett.). The average fire fractional area per one 1 km2 ×1 km2 pixel was 1.7%; this value corresponds to 32% of that of Siberian and Mongolian boreal forest fires. The average radiances at 4 and 11 μm of active fires were 7.2 W/(m2.sr.μm) and 11.1 W/(m2.sr.μm); these values correspond to 47% and 91% of those of Siberian and Mongolian boreal forest fires, respectively. In order to get false alarms less than 20 points per 106 km2 area, for the Siberian and Mongolian boreal forest fires, omission errors (OE) of 50-60% and about 40% were expected for the detections by using the single and multitemporal images, respectively. For Indonesian peat fires, OE of 80-90% was expected for the detections by using the single images. For the peat-fire detections by using the multitemporal images, OE of about 40% was expected, provided that the background radiances were estimated from past multitemporal images with less than the standard deviation of 1K. The analyses indicated that it was difficult to obtain sufficient active-fire information of Indonesian peat fires from single MODIS images for the fire fighting, and that the use of the multitemporal images was important.

  4. Polarized radiance distribution measurements of skylight. I. System description and characterization.

    PubMed

    Voss, K J; Liu, Y

    1997-08-20

    A new system to measure the natural skylight polarized radiance distribution has been developed. The system is based on a fish-eye lens, CCD camera system, and filter changer. With this system sequences of images can be combined to determine the linear polarization components of the incident light field. Calibration steps to determine the system 's polarization characteristics are described. Comparisons of the radiance measurements of this system and a simple pointing radiometer were made in the field and agreed within 10 % for measurements at 560 and 670 nm and 25 % at 860 nm. Polarization tests were done in the laboratory. The accuracy of the intensity measurements is estimated to be 10 %, while the accuracy of measurements of elements of the Mueller matrix are estimated to be 2 %.

  5. Nimbus 7 Solar Backscatter Ultraviolet (SBUV) spectral scan solar irradiance and Earth radiance product user's guide

    NASA Technical Reports Server (NTRS)

    Schlesinger, Barry M.; Cebula, Richard P.; Heath, Donald F.; Fleig, Albert J.

    1988-01-01

    The archived tape products from the spectral scan mode measurements of solar irradiance (SUNC tapes) and Earth radiance (EARTH tapes) by the Solar Backscatter UV (SBUV) instrument aboard Nimbus 7 are described. Incoming radiation from 160 to 400 nm is measured at intervals of 0.2 nm. The scan-to-scan repeatability of the solar irradiance measurements ranges from approximately 0.5 to 1 percent longward of 280 nm, to 2 percent around 210 nm and 4 percent near 175 nm. The repeatability of the Earth radiance values ranges from 2 to 3 percent at longer wavelengths and low zenith angles to 10 percent at shorter wavelengths and high zenith angles. The tape formats are described in detail, including file structure and contents of each type of record. Catalogs of the tapes and the time period covered are provided, along with lists of the days lacking solar irradiance measurements and the days dedicated to Earth radiance measurements. The method for production of the tapes is outlined and quality control measures are described. How radiances and irradiances are derived from the raw counts, the corrections for changes in instrument sensitivity, and related uncertainties are discussed.

  6. Assessment of Mars Atmospheric Temperature Retrievals from the Thermal Emission Spectrometer Radiances

    NASA Technical Reports Server (NTRS)

    Hoffman, Matthew J.; Eluszkiewicz, Janusz; Weisenstein, Deborah; Uymin, Gennady; Moncet, Jean-Luc

    2012-01-01

    Motivated by the needs of Mars data assimilation. particularly quantification of measurement errors and generation of averaging kernels. we have evaluated atmospheric temperature retrievals from Mars Global Surveyor (MGS) Thermal Emission Spectrometer (TES) radiances. Multiple sets of retrievals have been considered in this study; (1) retrievals available from the Planetary Data System (PDS), (2) retrievals based on variants of the retrieval algorithm used to generate the PDS retrievals, and (3) retrievals produced using the Mars 1-Dimensional Retrieval (M1R) algorithm based on the Optimal Spectral Sampling (OSS ) forward model. The retrieved temperature profiles are compared to the MGS Radio Science (RS) temperature profiles. For the samples tested, the M1R temperature profiles can be made to agree within 2 K with the RS temperature profiles, but only after tuning the prior and error statistics. Use of a global prior that does not take into account the seasonal dependence leads errors of up 6 K. In polar samples. errors relative to the RS temperature profiles are even larger. In these samples, the PDS temperature profiles also exhibit a poor fit with RS temperatures. This fit is worse than reported in previous studies, indicating that the lack of fit is due to a bias correction to TES radiances implemented after 2004. To explain the differences between the PDS and Ml R temperatures, the algorithms are compared directly, with the OSS forward model inserted into the PDS algorithm. Factors such as the filtering parameter, the use of linear versus nonlinear constrained inversion, and the choice of the forward model, are found to contribute heavily to the differences in the temperature profiles retrieved in the polar regions, resulting in uncertainties of up to 6 K. Even outside the poles, changes in the a priori statistics result in different profile shapes which all fit the radiances within the specified error. The importance of the a priori statistics prevents

  7. Retrieving SW fluxes from geostationary narrowband radiances for the NASA-CERES SYN1deg product

    NASA Astrophysics Data System (ADS)

    Wrenn, F. J., IV; Doelling, D. R.; Liang, L.

    2016-12-01

    The CERES mission was designed to measure the natural variability of the net TOA flux over long time scales relevant to climate monitoring. To achieve this goal, CERES provides the level-3 SSF1deg, SYN1deg, and EBAF monthly 1° by 1° regional TOA flux. The single satellite (Terra or Aqua) SSF1deg 24-hour shortwave flux is based on one daytime measurements and assumes constant meteorology to model the diurnal change in albedo. To accurately describe regions with a prominent diurnal signal, the SYN1deg Edition4 dataset employs hourly geostationary (GEO) measurements. This improves upon Edition3, which used 3-hourly GEO measurements and with temporal interpolation. The EBAF product combines the temporal stability of the SSF1deg product with the diurnal information from SYN1deg and removes the CERES instrument calibration bias by constraining the net flux balance to the ocean heat storage term. The SYN-1deg product retrieves hourly SW fluxes from GEO measurements. Over regions with large diurnal cycles, such as maritime stratus and land afternoon convective locations, the GEO derived SW fluxes will capture the diurnal flux not observed with Terra or Aqua sun-synchronous satellites. Obtaining fluxes from geostationary satellite radiance is a multistep process. First, most GEO visible imagers lack calibration and must be calibrated to MODIS and VIIRS. Second, the GEO imager visible channel radiances are converted to broadband radiances using empirical and theoretical models. The lack of coincident, collocated, and co-angled GEO and CERES measurements makes building an empirical model difficult. The narrowband to broadband models are a function of surface and cloud conditions, which are difficult to identify due to the inconsistent cloud retrievals between the 16 GEO imagers used in the CERES record. Third, the GEO derived broadband radiances are passed through the CERES angular distribution model (ADM) to convert the radiances to fluxes. Lastly, the GEO derived

  8. Retrieving SW fluxes from geostationary narrowband radiances for the NASA-CERES SYN1deg product

    NASA Astrophysics Data System (ADS)

    Wrenn, F. J., IV; Doelling, D. R.; Liang, L.

    2017-12-01

    The CERES mission was designed to measure the natural variability of the net TOA flux over long time scales relevant to climate monitoring. To achieve this goal, CERES provides the level-3 SSF1deg, SYN1deg, and EBAF monthly 1° by 1° regional TOA flux. The single satellite (Terra or Aqua) SSF1deg 24-hour shortwave flux is based on one daytime measurements and assumes constant meteorology to model the diurnal change in albedo. To accurately describe regions with a prominent diurnal signal, the SYN1deg Edition4 dataset employs hourly geostationary (GEO) measurements. This improves upon Edition3, which used 3-hourly GEO measurements and with temporal interpolation. The EBAF product combines the temporal stability of the SSF1deg product with the diurnal information from SYN1deg and removes the CERES instrument calibration bias by constraining the net flux balance to the ocean heat storage term. The SYN-1deg product retrieves hourly SW fluxes from GEO measurements. Over regions with large diurnal cycles, such as maritime stratus and land afternoon convective locations, the GEO derived SW fluxes will capture the diurnal flux not observed with Terra or Aqua sun-synchronous satellites. Obtaining fluxes from geostationary satellite radiance is a multistep process. First, most GEO visible imagers lack calibration and must be calibrated to MODIS and VIIRS. Second, the GEO imager visible channel radiances are converted to broadband radiances using empirical and theoretical models. The lack of coincident, collocated, and co-angled GEO and CERES measurements makes building an empirical model difficult. The narrowband to broadband models are a function of surface and cloud conditions, which are difficult to identify due to the inconsistent cloud retrievals between the 16 GEO imagers used in the CERES record. Third, the GEO derived broadband radiances are passed through the CERES angular distribution model (ADM) to convert the radiances to fluxes. Lastly, the GEO derived

  9. Experimental validation of the MODTRAN 5.3 sea surface radiance model using MIRAMER campaign measurements.

    PubMed

    Ross, Vincent; Dion, Denis; St-Germain, Daniel

    2012-05-01

    Radiometric images taken in mid-wave and long-wave infrared bands are used as a basis for validating a sea surface bidirectional reflectance distribution function (BRDF) being implemented into MODTRAN 5 (Berk et al. [Proc. SPIE5806, 662 (2005)]). The images were obtained during the MIRAMER campaign that took place in May 2008 in the Mediterranean Sea near Toulon, France. When atmosphere radiances are matched at the horizon to remove possible calibration offsets, the implementation of the BRDF in MODTRAN produces good sea surface radiance agreement, usually within 2% and at worst 4% from off-glint azimuthally averaged measurements. Simulations also compare quite favorably to glint measurements. The observed sea radiance deviations between model and measurements are not systematic, and are well within expected experimental uncertainties. This is largely attributed to proper radiative coupling between the surface and the atmosphere implemented using the DISORT multiple scattering algorithm.

  10. Study on inverse estimation of radiative properties from directional radiances by using statistical RPSO algorithm

    NASA Astrophysics Data System (ADS)

    Han, Kuk-Il; Kim, Do-Hwi; Choi, Jun-Hyuk; Kim, Tae-Kuk; Shin, Jong-Jin

    2016-09-01

    Infrared signals are widely used to discriminate objects against the background. Prediction of infrared signal from an object surface is essential in evaluating the detectability of the object. Appropriate and easy method of procurement of the radiative properties such as the surface emissivity, bidirectional reflectivity is important in estimating infrared signals. Direct measurement can be a good choice but a costly and time consuming way of obtaining the radiative properties for surfaces coated with many different newly developed paints. Especially measurement of the bidirectional reflectivity usually expressed by the bidirectional reflectance distribution function (BRDF) is the most costly job. In this paper we are presenting an inverse estimation method of the radiative properties by using the directional radiances from the surface of concern. The inverse estimation method used in this study is the statistical repulsive particle swarm optimization (RPSO) algorithm which uses the randomly picked directional radiance data emitted and reflected from the surface. In this paper, we test the proposed inverse method by considering the radiation from a steel plate surface coated with different paints at a clear sunny day condition. For convenience, the directional radiance data from the steel plate within a spectral band of concern are obtained from the simulation using the commercial software, RadthermIR, instead of the field measurement. A widely used BRDF model called as the Sandford-Robertson(S-R) model is considered and the RPSO process is then used to find the best fitted model parameters for the S-R model. The results obtained from this study show an excellent agreement with the reference property data used for the simulation for directional radiances. The proposed process can be a useful way of obtaining the radiative properties from field measured directional radiance data for surfaces coated with or without various kinds of paints of unknown radiative

  11. Factors affecting construction performance: exploratory factor analysis

    NASA Astrophysics Data System (ADS)

    Soewin, E.; Chinda, T.

    2018-04-01

    The present work attempts to develop a multidimensional performance evaluation framework for a construction company by considering all relevant measures of performance. Based on the previous studies, this study hypothesizes nine key factors, with a total of 57 associated items. The hypothesized factors, with their associated items, are then used to develop questionnaire survey to gather data. The exploratory factor analysis (EFA) was applied to the collected data which gave rise 10 factors with 57 items affecting construction performance. The findings further reveal that the items constituting ten key performance factors (KPIs) namely; 1) Time, 2) Cost, 3) Quality, 4) Safety & Health, 5) Internal Stakeholder, 6) External Stakeholder, 7) Client Satisfaction, 8) Financial Performance, 9) Environment, and 10) Information, Technology & Innovation. The analysis helps to develop multi-dimensional performance evaluation framework for an effective measurement of the construction performance. The 10 key performance factors can be broadly categorized into economic aspect, social aspect, environmental aspect, and technology aspects. It is important to understand a multi-dimension performance evaluation framework by including all key factors affecting the construction performance of a company, so that the management level can effectively plan to implement an effective performance development plan to match with the mission and vision of the company.

  12. Radiance and polarization of multiple scattered light from haze and clouds.

    PubMed

    Kattawar, G W; Plass, G N

    1968-08-01

    The radiance and polarization of multiple scattered light is calculated from the Stokes' vectors by a Monte Carlo method. The exact scattering matrix for a typical haze and for a cloud whose spherical drops have an average radius of 12 mu is calculated from the Mie theory. The Stokes' vector is transformed in a collision by this scattering matrix and the rotation matrix. The two angles that define the photon direction after scattering are chosen by a random process that correctly simulates the actual distribution functions for both angles. The Monte Carlo results for Rayleigh scattering compare favorably with well known tabulated results. Curves are given of the reflected and transmitted radiances and polarizations for both the haze and cloud models and for several solar angles, optical thicknesses, and surface albedos. The dependence on these various parameters is discussed.

  13. The thermal infrared radiance properties of dust aerosol over ocean

    NASA Astrophysics Data System (ADS)

    Hao, Zengzhou; Pan, Delu; Tu, Qianguang; Gong, Fang; Chen, Jianyu

    2015-10-01

    Asian dust storms, which can long-range transport to ocean, often occur on spring. The present of Asian dust aerosols over ocean makes some difficult for other studies, such as cloud detection, and also take some advantage for ocean, such as take nutrition into the ocean by dry or wet deposition. Therefore, it is important to study the dust aerosol and retrieve the properties of dust from satellite observations that is mainly from the thermal infrared radiance. In this paper, the thermal infrared radiance properties of dust aerosol over ocean are analyzed from MODIS and MTSAT2 observations and Streamer model simulations. By analyzing some line samples and a series of dust aerosol region, it shows that the dust aerosol brightness temperature at 12μm (BT12) is always greater than BT11 and BT8.5, and BT8.5 is general greater than BT11. The brightness temperature different between 11μm and 12μm (BTD11-12) increases with the dust intensity. And the BTD11-12 will become positive when the atmospheric relative humidity is greater than 70%. The BTD11-12 increases gradually with the surface temperature while the effect on BTD11-12 of dust layer temperature is not evident. Those are caused by the transmission of the dust aerosol is different at the two thermal infrared channels. During daytime, dust infrared brightness temperature at mid-infrared bands should reduce the visual radiance, which takes about 25K or less. In general, BT3.7 is greater than BT11 for dust aerosol. Those results are helpful to monitor or retrieve dust aerosol physical properties over ocean from satellite.

  14. Validation of a weather forecast model at radiance level against satellite observations allowing quantification of temperature, humidity, and cloud-related biases

    NASA Astrophysics Data System (ADS)

    Bani Shahabadi, Maziar; Huang, Yi; Garand, Louis; Heilliette, Sylvain; Yang, Ping

    2016-09-01

    An established radiative transfer model (RTM) is adapted for simulating all-sky infrared radiance spectra from the Canadian Global Environmental Multiscale (GEM) model in order to validate its forecasts at the radiance level against Atmospheric InfraRed Sounder (AIRS) observations. Synthetic spectra are generated for 2 months from short-term (3-9 h) GEM forecasts. The RTM uses a monthly climatological land surface emissivity/reflectivity atlas. An updated ice particle optical property library was introduced for cloudy radiance calculations. Forward model brightness temperature (BT) biases are assessed to be of the order of ˜1 K for both clear-sky and overcast conditions. To quantify GEM forecast meteorological variables biases, spectral sensitivity kernels are generated and used to attribute radiance biases to surface and atmospheric temperatures, atmospheric humidity, and clouds biases. The kernel method, supplemented with retrieved profiles based on AIRS observations in collocation with a microwave sounder, achieves good closure in explaining clear-sky radiance biases, which are attributed mostly to surface temperature and upper tropospheric water vapor biases. Cloudy-sky radiance biases are dominated by cloud-induced radiance biases. Prominent GEM biases are identified as: (1) too low surface temperature over land, causing about -5 K bias in the atmospheric window region; (2) too high upper tropospheric water vapor, inducing about -3 K bias in the water vapor absorption band; (3) too few high clouds in the convective regions, generating about +10 K bias in window band and about +6 K bias in the water vapor band.

  15. A technique for directly comparing radiances from two satellites

    NASA Technical Reports Server (NTRS)

    Mcpeters, Richard D.

    1990-01-01

    Solar Backscattering Ultraviolet-2 (SBUV/2) instrument on NOAA-9 orbit on June 1987, solar zenith angles of the observations; plot of weekly average differences between SBUV (Nimbus-7 and SBUV/2 (NOAA-9); radiance comparisons for March 1986; time dependence of relative change between SBUV and SBUV/2; and explicit wavelength dependence are presented in viewgraph format. Each is briefly discussed.

  16. Factors Affecting Medical Service Quality.

    PubMed

    Mosadeghrad, Ali Mohammad

    2014-02-01

    A better understanding of factors influencing quality of medical service can pinpoint better strategies for quality assurance in medical services. This study aimed to identify factors affecting the quality of medical services provided by Iranian physicians. Exploratory in-depth individual interviews were conducted with sixty-four physicians working in various medical institutions in Iran. Individual, organizational and environmental factors enhance or inhibit the quality of medical services. Quality of medical services depends on the personal factors of the physician and patient, and factors pertaining to the healthcare setting and the broader environment. Differences in internal and external factors such as availability of resources, patient cooperation and collaboration among providers affect the quality of medical services and patient outcomes. Supportive leadership, proper planning, education and training and effective management of resources and processes improve the quality of medical services. This article contributes to healthcare theory and practice by developing a conceptual framework for understanding factors that influence medical services quality.

  17. Evaluation of ISCCP multisatellite radiance calibration for geostationary imager visible channels using the moon

    USGS Publications Warehouse

    Stone, Thomas C.; William B. Rossow,; Joseph Ferrier,; Laura M. Hinkelman,

    2013-01-01

    Since 1983, the International Satellite Cloud Climatology Project (ISCCP) has collected Earth radiance data from the succession of geostationary and polar-orbiting meteorological satellites operated by weather agencies worldwide. Meeting the ISCCP goals of global coverage and decade-length time scales requires consistent and stable calibration of the participating satellites. For the geostationary imager visible channels, ISCCP calibration provides regular periodic updates from regressions of radiances measured from coincident and collocated observations taken by Advanced Very High Resolution Radiometer instruments. As an independent check of the temporal stability and intersatellite consistency of ISCCP calibrations, we have applied lunar calibration techniques to geostationary imager visible channels using images of the Moon found in the ISCCP data archive. Lunar calibration enables using the reflected light from the Moon as a stable and consistent radiometric reference. Although the technique has general applicability, limitations of the archived image data have restricted the current study to Geostationary Operational Environmental Satellite and Geostationary Meteorological Satellite series. The results of this lunar analysis confirm that ISCCP calibration exhibits negligible temporal trends in sensor response but have revealed apparent relative biases between the satellites at various levels. However, these biases amount to differences of only a few percent in measured absolute reflectances. Since the lunar analysis examines only the lower end of the radiance range, the results suggest that the ISCCP calibration regression approach does not precisely determine the intercept or the zero-radiance response level. We discuss the impact of these findings on the development of consistent calibration for multisatellite global data sets.

  18. Completeness of carotid intima media thickness measurements depends on body composition: the RADIANCE 1 and 2 trials.

    PubMed

    Dogan, Soner; Duivenvoorden, Raphaël; Grobbee, Diederick E; Kastelein, John J P; Shear, Charles L; Evans, Gregory W; Visseren, Frank L; Bots, Michiel L

    2010-05-01

    Ultrasound protocols to measure carotid intima media thickness (CIMT) differ considerably with regard to the inclusion of the number of carotid segments and angles used. Detailed information on the completeness of CIMT information is often lacking in published reports, and at most, overall percentages are presented. We therefore decided to study the completeness of CIMT measurements and its relation with vascular risk factors using data from two CIMT intervention studies: one among familial hypercholesterolemia (FH) patients, the Rating Atherosclerotic Disease change by Imaging With A New CETP Inhibitor (RADIANCE 1), and one among mixed dyslipidemia (MD) patients, the Rating Atherosclerotic Disease change by Imaging With A New CETP Inhibitor (RADIANCE 2). We used baseline ultrasound scans from the RADIANCE 1 (n=872) and RADIANCE 2 (n=752) studies. CIMT images were recorded for 12 artery-wall combinations (near and far walls of the left and right common carotid artery (CCA), bifurcation (BIF) and internal carotid artery (ICA) segments) at 4 set angles, resulting in 48 possible measurements per patient. The presence or absence of CIMT measurements was assessed per artery-wall combination and per angle. The relation between completeness and patient characteristics was evaluated with logistic regression analysis. In 89% of the FH patients, information on CIMT could be obtained on all twelve carotid segments, and in 7.6%, eleven segments had CIMT information (nearly complete 96.6%). For MD patients this was 74.6% and 17.9%, respectively (nearly complete: 92.5%). Increased body mass index and increased waist circumference were significantly (p=0.01) related to less complete data in FH patients. For MD patients, relations were seen with increased waist circumference (p<0.01). Segment-specific data indicated that in FH patients, completeness was less for the near wall of the left (96%) and right internal carotid artery (94%) as compared to other segments (all >98%). In MD

  19. Reverse radiance: a fast accurate method for determining luminance

    NASA Astrophysics Data System (ADS)

    Moore, Kenneth E.; Rykowski, Ronald F.; Gangadhara, Sanjay

    2012-10-01

    Reverse ray tracing from a region of interest backward to the source has long been proposed as an efficient method of determining luminous flux. The idea is to trace rays only from where the final flux needs to be known back to the source, rather than tracing in the forward direction from the source outward to see where the light goes. Once the reverse ray reaches the source, the radiance the equivalent forward ray would have represented is determined and the resulting flux computed. Although reverse ray tracing is conceptually simple, the method critically depends upon an accurate source model in both the near and far field. An overly simplified source model, such as an ideal Lambertian surface substantially detracts from the accuracy and thus benefit of the method. This paper will introduce an improved method of reverse ray tracing that we call Reverse Radiance that avoids assumptions about the source properties. The new method uses measured data from a Source Imaging Goniometer (SIG) that simultaneously measures near and far field luminous data. Incorporating this data into a fast reverse ray tracing integration method yields fast, accurate data for a wide variety of illumination problems.

  20. Sea-based Infrared Radiance Measurements of Ocean and Atmosphere from the ACAPEX/CalWater2 Campaign

    NASA Astrophysics Data System (ADS)

    Gero, P. J.; Knuteson, R.; Hackel, D.; Phillips, C.; Westphall, M.

    2015-12-01

    The ARM Cloud Aerosol Precipitation Experiment (ACAPEX) / CalWater2 was a joint DOE/NOAA field campaign in early 2015 to study atmospheric rivers in the Pacific Ocean and their impacts on the western United States. The campaign goals were to improve understanding and modeling of large-scale dynamics and cloud and precipitation processes associated with atmospheric rivers and aerosol-cloud interactions that influence precipitation variability and extremes in the western United States. Coordinated measurements were made from ground-, aircraft- and sea-based platforms. The second ARM mobile facility (AMF-2) was deployed on board the NOAA Ship Ronald H. Brown for this campaign, which included a new Marine Atmospheric Emitted Radiance Interferometer (M-AERI) to measure the atmospheric downwelling and reflected infrared radiance spectrum at the Earth's surface with high absolute accuracy. The M-AERI measures spectral infrared radiance between 520-3020 cm-1 (3.3-19 μm) at a resolution of 0.5 cm-1. The M-AERI can selectively view the atmospheric scene at zenith, and ocean/atmospheric scenes over a range of ±45° from the horizon. The AERI uses two high-emissivity blackbodies for radiometric calibration, which in conjunction with the instrument design and a suite of rigorous laboratory diagnostics, ensures the radiometric accuracy to be better than 1% (3σ) of the ambient radiance. The M-AERI radiance spectra can be used to retrieve profiles of temperature and water vapor in the troposphere, as well as measurements of trace gases, cloud properties, surface emissivity and ocean skin temperature. We present preliminary results on measurements of ocean skin temperature, ocean emissivity properties as a function of view angle and wind speed, as well as comparisons with radiosondes and satellite observations.

  1. Evaluation of the Impact of Atmospheric Infrared Sounder (AIRS) Radiance and Profile Data Assimilation in Partly Cloudy Regions

    NASA Technical Reports Server (NTRS)

    Zavodsky, Bradley; Srikishen, Jayanthi; Jedlovec, Gary

    2013-01-01

    Improvements to global and regional numerical weather prediction have been demonstrated through assimilation of data from NASA s Atmospheric Infrared Sounder (AIRS). Current operational data assimilation systems use AIRS radiances, but impact on regional forecasts has been much smaller than for global forecasts. Retrieved profiles from AIRS contain much of the information that is contained in the radiances and may be able to reveal reasons for this reduced impact. Assimilating AIRS retrieved profiles in an identical analysis configuration to the radiances, tracking the quantity and quality of the assimilated data in each technique, and examining analysis increments and forecast impact from each data type can yield clues as to the reasons for the reduced impact. By doing this with regional scale models individual synoptic features (and the impact of AIRS on these features) can be more easily tracked. This project examines the assimilation of hyperspectral sounder data used in operational numerical weather prediction by comparing operational techniques used for AIRS radiances and research techniques used for AIRS retrieved profiles. Parallel versions of a configuration of the Weather Research and Forecasting (WRF) model with Gridpoint Statistical Interpolation (GSI) are run to examine the impact AIRS radiances and retrieved profiles. Statistical evaluation of 6 weeks of forecast runs will be compared along with preliminary results of in-depth investigations for select case comparing the analysis increments in partly cloudy regions and short-term forecast impacts.

  2. Comprehensive Understanding for Vegetated Scene Radiance Relationships

    NASA Technical Reports Server (NTRS)

    Kimes, D. S.; Deering, D. W.

    1984-01-01

    Directional reflectance distributions spanning the entire existent hemisphere were measured in two field studies; one using a Mark III 3-band radiometer and one using the rapid scanning bidirectional field instrument called PARABOLA. Surfaces measured included corn, soybeans, bare soils, grass lawn, orchard grass, alfalfa, cotton row crops, plowed field, annual grassland, stipa grass, hard wheat, salt plain shrubland, and irrigated wheat. Analysis of field data showed unique reflectance distributions ranging from bare soil to complete vegetation canopies. Physical mechanisms causing these trends were proposed. A 3-D model was developed and is unique in that it predicts: (1) the directional spectral reflectance factors as a function of the sensor's azimuth and zenith angles and the sensor's position above the canopy; (2) the spectral absorption as a function of location within the scene; and (3) the directional spectral radiance as a function of the sensor's location within the scene. Initial verification of the model as applied to a soybean row crop showed that the simulated directional data corresponded relatively well in gross trends to the measured data. The model was expanded to include the anisotropic scattering properties of leaves as a function of the leaf orientation distribution in both the zenith and azimuth angle modes.

  3. Impact of assimilating GOES imager clear-sky radiance with a rapid refresh assimilation system for convection-permitting forecast over Mexico

    NASA Astrophysics Data System (ADS)

    Yang, Chun; Liu, Zhiquan; Gao, Feng; Childs, Peter P.; Min, Jinzhong

    2017-05-01

    The Geostationary Operational Environmental Satellite (GOES) imager data could provide a continuous image of the evolutionary pattern of severe weather phenomena with its high spatial and temporal resolution. The capability to assimilate the GOES imager radiances has been developed within the Weather Research and Forecasting model's data assimilation system. Compared to the benchmark experiment with no GOES imager data, the impact of assimilating GOES imager radiances on the analysis and forecast of convective process over Mexico in 7-10 March 2016 was assessed through analysis/forecast cycling experiments using rapid refresh assimilation system with hybrid-3DEnVar scheme. With GOES imager radiance assimilation, better analyses were obtained in terms of the humidity, temperature, and simulated water vapor channel brightness temperature distribution. Positive forecast impacts from assimilating GOES imager radiance were seen when verified against the Tropospheric Airborne Meteorological Data Reporting observation, GOES imager observation, and Mexico station precipitation data.

  4. Detection of localized inclusions of gold nanoparticles in Intralipid-1% by point-radiance spectroscopy

    NASA Astrophysics Data System (ADS)

    Grabtchak, Serge; Palmer, Tyler J.; Whelan, William M.

    2011-07-01

    Interstitial fiber-optic-based approaches used in both diagnostic and therapeutic applications rely on localized light-tissue interactions. We present an optical technique to identify spectrally and spatially specific exogenous chromophores in highly scattering turbid media. Point radiance spectroscopy is based on directional light collection at a single point with a side-firing fiber that can be rotated up to 360 deg. A side firing fiber accepts light within a well-defined, solid angle, thus potentially providing an improved spatial resolution. Measurements were performed using an 800-μm diameter isotropic spherical diffuser coupled to a halogen light source and a 600 μm, ~43 deg cleaved fiber (i.e., radiance detector). The background liquid-based scattering phantom was fabricated using 1% Intralipid. Light was collected with 1 deg increments through 360 deg-segment. Gold nanoparticles , placed into a 3.5-mm diameter capillary tube were used as localized scatterers and absorbers introduced into the liquid phantom both on- and off-axis between source and detector. The localized optical inhomogeneity was detectable as an angular-resolved variation in the radiance polar plots. This technique is being investigated as a potential noninvasive optical modality for prostate cancer monitoring.

  5. Detection of localized inclusions of gold nanoparticles in Intralipid-1% by point-radiance spectroscopy.

    PubMed

    Grabtchak, Serge; Palmer, Tyler J; Whelan, William M

    2011-07-01

    Interstitial fiber-optic-based approaches used in both diagnostic and therapeutic applications rely on localized light-tissue interactions. We present an optical technique to identify spectrally and spatially specific exogenous chromophores in highly scattering turbid media. Point radiance spectroscopy is based on directional light collection at a single point with a side-firing fiber that can be rotated up to 360 deg. A side firing fiber accepts light within a well-defined, solid angle, thus potentially providing an improved spatial resolution. Measurements were performed using an 800-μm diameter isotropic spherical diffuser coupled to a halogen light source and a 600 μm, ∼43 deg cleaved fiber (i.e., radiance detector). The background liquid-based scattering phantom was fabricated using 1% Intralipid. Light was collected with 1 deg increments through 360 deg-segment. Gold nanoparticles , placed into a 3.5-mm diameter capillary tube were used as localized scatterers and absorbers introduced into the liquid phantom both on- and off-axis between source and detector. The localized optical inhomogeneity was detectable as an angular-resolved variation in the radiance polar plots. This technique is being investigated as a potential noninvasive optical modality for prostate cancer monitoring.

  6. Patterns of reflected radiance associated with geobotanical anomalies

    NASA Technical Reports Server (NTRS)

    Birnie, R. W.; Stone, T. A.; Francica, J. R.

    1985-01-01

    This paper summarizes three remote sensing experiments in which changes in remotely measured reflected radiance patterns of vegetation correlated with changes in geology. In two cases using airborne spectroradiometer data, changes in the physical properties of a uniform species correlated with zones of porphyry copper mineralization. In another case using Landsat digital data, changes were detected in the distribution and density of a number of species and combined with soil brightness data to produce a composite index useful for distinguishing lithologies.

  7. Monte Carlo and discrete-ordinate simulations of spectral radiances in a coupled air-tissue system.

    PubMed

    Hestenes, Kjersti; Nielsen, Kristian P; Zhao, Lu; Stamnes, Jakob J; Stamnes, Knut

    2007-04-20

    We perform a detailed comparison study of Monte Carlo (MC) simulations and discrete-ordinate radiative-transfer (DISORT) calculations of spectral radiances in a 1D coupled air-tissue (CAT) system consisting of horizontal plane-parallel layers. The MC and DISORT models have the same physical basis, including coupling between the air and the tissue, and we use the same air and tissue input parameters for both codes. We find excellent agreement between radiances obtained with the two codes, both above and in the tissue. Our tests cover typical optical properties of skin tissue at the 280, 540, and 650 nm wavelengths. The normalized volume scattering function for internal structures in the skin is represented by the one-parameter Henyey-Greenstein function for large particles and the Rayleigh scattering function for small particles. The CAT-DISORT code is found to be approximately 1000 times faster than the CAT-MC code. We also show that the spectral radiance field is strongly dependent on the inherent optical properties of the skin tissue.

  8. Use of MODIS Cloud Top Pressure to Improve Assimilation Yields of AIRS Radiances in GSI

    NASA Technical Reports Server (NTRS)

    Zavodsky, Bradley; Srikishen, Jayanthi

    2014-01-01

    Improvements to global and regional numerical weather prediction have been demonstrated through assimilation of data from NASA's Atmospheric Infrared Sounder (AIRS). Current operational data assimilation systems use AIRS radiances, but impact on regional forecasts has been much smaller than for global forecasts. Previously, it has been shown that cloud top designation associated with quality control procedures within the Gridpoint Statistical Interpolation (GSI) system used operationally by a number of Joint Center for Satellite Data Assimilation (JCSDA) partners may not provide the best representation of cloud top pressure (CTP). Because this designated CTP determines which channels are cloud-free and, thus, available for assimilation, ensuring the most accurate representation of this value is imperative to obtaining the greatest impact from satellite radiances. This paper examines the assimilation of hyperspectral sounder data used in operational numerical weather prediction by comparing analysis increments and numerical forecasts generated using operational techniques with a research technique that swaps CTP from the Moderate-resolution Imaging Spectroradiometer (MODIS) for the value of CTP calculated from the radiances within GSI.

  9. Laboratory upwelled radiance and reflectance spectra of Kerr reservoir sediment waters

    NASA Technical Reports Server (NTRS)

    Witte, W. G.; Whitlock, C. H.; Morris, W. D.; Gurganus, E. A.

    1982-01-01

    Reflectance, chromaticity, and several other physical and chemical properties were measured for various water mixtures of bottom sediments taken from two sites at Kerr Reservoir, Virginia. Mixture concentrations ranged from 5 to 1000 ppm by weight of total suspended solids (TSS) in filtered deionized tap water. The two sets of radiance and reflectance spectra obtained were similar in shape and magnitude for comparable values of TSS. Upwelled reflectance was observed to be a nonlinear function of TSS with the degree of curvature a function of wavelength. Sediment from the downstream site contained a greater amount of particulate organic carbon than from the upstream site. No strong conclusions can be made regarding the effects of this difference on the radiance and reflectance spectra. Near-infrared wavelengths appear useful for measuring highly turbid water with concentrations up to 1000 ppm or more. Chromaticity characteristics do not appear useful for monitoring sediment loads above 150 ppm.

  10. Factors affecting the remotely sensed response of coniferous forest plantations

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Danson, F.M.; Curran, P.J.

    1993-01-01

    Remote sensing of forest biophysical properties has concentrated upon forest sites with a wide range of green vegetation amount and thereby leaf area index and canopy cover. However, coniferous forest plantations, an important forest type in Europe, are managed to maintain a large amount of green vegetation with little spatial variation. Therefore, the strength of the remotely sensed signal will, it is hypothesized, be determined more by the structure of this forest than by its cover. Airborne Thematic Mapper (ATM) and SPOT-1 HRV data were used to determine the effects of this structural variation on the remotely sensed response ofmore » a coniferous forest plantation in the United Kingdom. Red and near infrared radiance were strongly and negatively correlated with a range of structural properties and with the age of the stands but weakly correlated with canopy cover. A composite variable, related to the volume of the canopy, accounted for over 75% of the variation in near infrared radiance. A simple model that related forest structural variables to the remotely sensed response was used to understand and explain this response from a coniferous forest plantation.« less

  11. Interior radiances in optically deep absorbing media. 1: Exact solutions for one-dimensional model

    NASA Technical Reports Server (NTRS)

    Kattawar, G. W.; Plass, G. N.

    1973-01-01

    The exact solutions are obtained for a one dimensional model of a scattering and absorbing medium. The results are given for both the reflected and transmitted radiance for any arbitrary surface albedo as well as for the interior radiance. These same quantities are calculated by the matrix operator method. The relative error of the solutions is obtained by comparison with the exact solutions as well as by an error analysis of the equations. The importance of an accurate starting value for the reflection and transmission operators is shown. A fourth order Runge-Kutta method can be used to solve the differential equations satisfied by these operators in order to obtain such accurate starting values.

  12. GOSAT and OCO-2 Inter-comparison on Measured Spectral Radiance and Retrieved Carbon Dioxide

    NASA Astrophysics Data System (ADS)

    Kataoka, F.; Kuze, A.; Shiomi, K.; Suto, H.; Crisp, D.; Bruegge, C. J.; Schwandner, F. M.

    2016-12-01

    TANSO-FTS onboard GOSAT and grating spectrometer on OCO-2 use different measurement techniques to measure carbon dioxide (CO2) and molecular oxygen (O2). Both instruments observe sunlight reflected from the Earth's surface in almost the same spectral range. As a first step in cross calibrating these two instruments, we compared spectral radiance observations within the three short wave infrared (SWIR) spectral bands centered on the O2 A-band (O2A), the weak CO2 band near 1.6 microns (Weak-CO2) and 2.06 micons (Strong-CO2) bands at temporally coincident and spatially collocated points. In this work, we reconciled the different size of the footprints and evaluated at various types of surface targets such as ocean, desert and forest. For radiometric inter-comparisons, we consider long term instrument sensitivity degradation in orbit and differences in viewing geometry and associated differences in surface bidirectional reflectance distribution function (BRDF). Measured spectral radiances agree very well within 5% for all bands. This presentation will summarize these comparisons of GOSAT and OCO-2 spectral radiance observations and associated estimates of carbon dioxide and related parameters retrieved with the same algorithm at matchup points. We will also discuss instrument related uncertainties from various target observations.

  13. Factors Affecting Tocopherol Concentrations in Soybean Seeds.

    PubMed

    Carrera, Constanza S; Seguin, Philippe

    2016-12-21

    Soybean seeds contain several health-beneficial compounds, including tocopherols, which are used by the nutraceutical and functional food industries. Soybean tocopherol concentrations are, however, highly variable. Large differences observed in tocopherol concentrations among soybean genotypes together with the relatively simple biosynthetic pathway involving few genes support the feasibility of selecting for high-tocopherol soybean. Tocopherol concentrations are also highly influenced by environmental factors and field management. Temperature during seed filling and soil moisture appear to be the main factors affecting tocopherol concentrations; other factors such as soil fertility and solar radiation also affect concentrations and composition. Field management decisions including seeding date, row spacing, irrigation, and fertilization also affect tocopherols. Knowledge of factors affecting soybean tocopherols is essential to develop management strategies that will lead to the production of seeds with consistent target concentrations that will meet the needs of the nutraceutical and functional food industries.

  14. Radiance distribution over a ruffled sea: contributions from glitter, sky, and ocean.

    PubMed

    Plass, G N; Kattawar, G W; Guinn, J A

    1976-12-01

    The upward radiance just above the ocean surface and at the top of the atmosphere is calculated for a realistic model including an ocean surface with waves. The separate contributions of the sun glitter, the reflected sky radiance, and the upwelling photons from the ocean are calculated. The Monte Carlo method takes account of both Rayleigh scattering by the molecules and Mie scattering by the aerosols as well as molecular and aerosol absorption in the atmosphere. Similarly, in the ocean, both Rayleigh scattering by the water molecules and Mie scattering by the hydrosols as well as absorption by the water molecules and hydrosols are considered. Separate single-scattering functions are used for the aerosols and hydrosols calculated from the Mie theory. Both the reflected and refracted rays, as well as the rays that undergo total internal reflection, are followed at the ocean surface. The wave slope is chosen from the Cox-Munk distribution. The upward radiance just above the ocean surface outside of the sun glitter region is dominated by the reflected sky radiation from the horizon to a nadir angle of observation of from 68 degrees to 23 degrees depending on the azimuthal angle and the solar zenith angle; the upwelling photons from the ocean dominate over the remainder of the hemisphere, except in the region of the sun glitter which centers around the mirror image of the sun on a calm ocean. It is possible to answer various questions about the interaction of light with the ocean from the quantitative results presented here.

  15. A New Marine Atmospheric Emitted Radiance Interferometer (M-AERI) for Shipboard Atmospheric and Oceanic Observations

    NASA Astrophysics Data System (ADS)

    Gero, P. J.; Knuteson, R. O.; Hackel, D.; Best, F. A.; Garcia, R.; Phillips, C.; Revercomb, H. E.; Smith, W. L.; Verret, E.; Lantagne, S. M.; Roy, C. B.

    2014-12-01

    A new ship-based Fourier transform spectrometer has been developed to measure the atmospheric downwelling and reflected infrared radiance spectrum at the Earth's surface with high absolute accuracy. This instrument was designed and built by ABB (Québec, Canada) based on the heritage of the Atmospheric Emitted Radiance Interferometer (AERI) designed by the University of Wisconsin Space Science and Engineering Center (UW-SSEC) for the Department of Energy (DOE) Atmospheric Radiation Measurement (ARM) Program. Prior versions of the M-AERI have been operated by the University of Miami for over a decade on research ships transiting the Atlantic and Pacific in support of NASA and NOAA satellite validation. The M-AERI measures infrared radiance between 520-3020 cm-1 (3.3-19 μm), at a resolution of 1 cm-1, using two detectors cooled to cryogenic temperatures with a Stirling cycle cooler. A gold-coated rotating scene mirror allows the M-AERI to selectively view the atmospheric scene at zenith, and ocean/atmospheric scenes over a range of +/- 45° from the horizon. The AERI uses two high-emissivity blackbodies for radiometric calibration, which in conjunction with the instrument design and a suite of rigorous laboratory diagnostics, ensures the radiometric accuracy to be better than 1% (3σ) of the ambient radiance. The M-AERI radiance spectra can be used to retrieve profiles of temperature and water vapor in the troposphere, as well as measurements of trace gases, cloud properties, and ocean skin temperature. The M-AERI measurement of ocean skin temperature has a demonstrated accuracy of better than 0.1 K. The first marine deployment of the new M-AERI will be as part of the second ARM mobile facility (AMF-2) during the ARM Cloud Aerosol Precipitation Experiment (ACAPEX) on board the NOAA Ship Ronald H. Brown in early 2015, occurring jointly with the NOAA CalWater 2 experiment. This field campaign aims to improve understanding and modeling of large-scale dynamics and cloud

  16. Potential for the use of reconstructed IASI radiances in the detection of atmospheric trace gases

    NASA Astrophysics Data System (ADS)

    Atkinson, N. C.; Hilton, F. I.; Illingworth, S. M.; Eyre, J. R.; Hultberg, T.

    2010-02-01

    Principal component (PC) analysis has received considerable attention as a technique for the extraction of meteorological signals from hyperspectral infra-red sounders such as the Infrared Atmospheric Sounding Interferometer (IASI) and the Atmospheric Infrared Sounder (AIRS). In addition to achieving substantial bit-volume reductions for dissemination purposes, the technique can also be used to generate reconstructed radiances in which random instrument noise has been suppressed. To date, most studies have been in the context of Numerical Weather Prediction (NWP). This study examines the potential of PC analysis for chemistry applications. A major concern in the use of PC analysis for chemistry has been that the spectral features associated with trace gases may not be well represented in the reconstructed spectra, either due to deficiencies in the training set or due to the limited number of PC scores used in the radiance reconstruction. In this paper we show examples of reconstructed IASI radiances for several trace gases: ammonia, sulphur dioxide, methane and carbon monoxide. It is shown that care must be taken in the selection of spectra for the initial training set: an iterative technique, in which outlier spectra are added to a base training set, gives the best results. For the four trace gases examined, the chemical signatures are retained in the reconstructed radiances, whilst achieving a substantial reduction in instrument noise. A new regional re-transmission service for IASI is scheduled to start in 2010, as part of the EUMETSAT Advanced Retransmission Service (EARS). For this EARS-IASI service it is intended to include PC scores as part of the data stream. The paper describes the generation of the reference eigenvectors for this new service.

  17. Web-based Factors Affecting Online Purchasing Behaviour

    NASA Astrophysics Data System (ADS)

    Ariff, Mohd Shoki Md; Sze Yan, Ng; Zakuan, Norhayati; Zaidi Bahari, Ahamad; Jusoh, Ahmad

    2013-06-01

    The growing use of internet and online purchasing among young consumers in Malaysia provides a huge prospect in e-commerce market, specifically for B2C segment. In this market, if E-marketers know the web-based factors affecting online buyers' behaviour, and the effect of these factors on behaviour of online consumers, then they can develop their marketing strategies to convert potential customers into active one, while retaining existing online customers. Review of previous studies related to the online purchasing behaviour in B2C market has point out that the conceptualization and empirical validation of the online purchasing behaviour of Information and Communication Technology (ICT) literate users, or ICT professional, in Malaysia has not been clearly addressed. This paper focuses on (i) web-based factors which online buyers (ICT professional) keep in mind while shopping online; and (ii) the effect of web-based factors on online purchasing behaviour. Based on the extensive literature review, a conceptual framework of 24 items of five factors was constructed to determine web-based factors affecting online purchasing behaviour of ICT professional. Analysis of data was performed based on the 310 questionnaires, which were collected using a stratified random sampling method, from ICT undergraduate students in a public university in Malaysia. The Exploratory factor analysis performed showed that five factors affecting online purchase behaviour are Information Quality, Fulfilment/Reliability/Customer Service, Website Design, Quick and Details, and Privacy/Security. The result of Multiple Regression Analysis indicated that Information Quality, Quick and Details, and Privacy/Security affect positively online purchase behaviour. The results provide a usable model for measuring web-based factors affecting buyers' online purchase behaviour in B2C market, as well as for online shopping companies to focus on the factors that will increase customers' online purchase.

  18. Characterization of Polar Stratospheric Cloud-Producing Mountain Waves using Thermal Radiance Imagery from the Advanced Microwave Sounding Unit (AMSU-A)

    NASA Astrophysics Data System (ADS)

    Eckermann, S. D.; Wu, D. L.; Doyle, J. D.; Burris, J. F.; McGee, T. J.; Hostetler, C. A.; Lawrence, B. N.; Stephens, A.; McCormack, J. P.; Coy, L.; Hogan, T. F.

    2006-12-01

    The Advanced Microwave Sounding Unit (AMSU-A) acquires pushbroom thermal radiance imagery from the NOAA 15-18 meteorological satellites and NASA's Aqua research satellite. We develop a simplified forward model of its in-orbit radiance acquisition and use it to demonstrate that the swath-scanned Channel 9 radiances (peaking at ~60--90~hPa) can resolve and horizontally image long wavelength gravity waves. To validate these inferences, we isolate and study structure in Channel 9 radiances acquired by AMSU-A instruments over Scandinavia on 14 January 2003. On this day, mountain waves were forecast to form polar stratospheric clouds (PSCs) over southern Scandinavia during NASA's second SAGE III Ozone Loss and Validation Experiment (SOLVE II) out of Kiruna, Sweden. Based on this forecast guidance, a flight was planned with NASA's DC-8 research aircraft, in which onboard aerosol lidars measured extensive tilted layers of enhanced aerosol backscatter typical of type II PSCs formed in the cooling phases of mountain waves. We show that these PSC-forming mountain waves were imaged in AMSU-A Channel 9 radiance imagery, which shows the waves growing in amplitude from 0600-1200 UTC and then weakening slightly and changing horizontal structure from 1200-2000 UTC. Our forward model results are used to infer 90 hPa peak wave temperature amplitudes of ~6--7~K, values validated by radiosonde data and full three-dimensional in-orbit forward modeling of three-dimensional temperatures, as forecast/hindcast by a suite of global and mesoscale numerical weather prediction models. These results demonstrate that AMSU-A radiances can provide important new hemispheric information on the role of long-wavelength stratospheric mountain waves in PSC formation, denitrification and polar ozone loss.

  19. A single field of view method for retrieving tropospheric temperature profiles from cloud-contaminated radiance data

    NASA Technical Reports Server (NTRS)

    Hodges, D. B.

    1976-01-01

    An iterative method is presented to retrieve single field of view (FOV) tropospheric temperature profiles directly from cloud-contaminated radiance data. A well-defined temperature profile may be calculated from the radiative transfer equation (RTE) for a partly cloudy atmosphere when the average fractional cloud amount and cloud-top height for the FOV are known. A cloud model is formulated to calculate the fractional cloud amount from an estimated cloud-top height. The method is then examined through use of simulated radiance data calculated through vertical integration of the RTE for a partly cloudy atmosphere using known values of cloud-top height(s) and fractional cloud amount(s). Temperature profiles are retrieved from the simulated data assuming various errors in the cloud parameters. Temperature profiles are retrieved from NOAA-4 satellite-measured radiance data obtained over an area dominated by an active cold front and with considerable cloud cover and compared with radiosonde data. The effects of using various guessed profiles and the number of iterations are considered.

  20. Feasibility of inverse problem solution for determination of city emission function from night sky radiance measurements

    NASA Astrophysics Data System (ADS)

    Petržala, Jaromír

    2018-07-01

    The knowledge of the emission function of a city is crucial for simulation of sky glow in its vicinity. The indirect methods to achieve this function from radiances measured over a part of the sky have been recently developed. In principle, such methods represent an ill-posed inverse problem. This paper deals with the theoretical feasibility study of various approaches to solving of given inverse problem. Particularly, it means testing of fitness of various stabilizing functionals within the Tikhonov's regularization. Further, the L-curve and generalized cross validation methods were investigated as indicators of an optimal regularization parameter. At first, we created the theoretical model for calculation of a sky spectral radiance in the form of a functional of an emission spectral radiance. Consequently, all the mentioned approaches were examined in numerical experiments with synthetical data generated for the fictitious city and loaded by random errors. The results demonstrate that the second order Tikhonov's regularization method together with regularization parameter choice by the L-curve maximum curvature criterion provide solutions which are in good agreement with the supposed model emission functions.

  1. Assessment of a Bidirectional Reflectance Distribution Correction of Above-Water and Satellite Water-Leaving Radiance in Coastal Waters

    DTIC Science & Technology

    2012-01-10

    water and satellite water-leaving radiance data for bidirectional effects. The proposed model is first validated with a one year time series of in situ... model is proposed to correct above-water and satellite water-leaving radiance data for bidirectional effects. The proposed model is first validated with...proposed model over the current one, demonstrating the need for a specific case 2 water BRDF correction algorithm as well as the feasibility of enhancing

  2. The Expected Impacts of NPOESS Microwave and Infrared Sounder Radiances on Operational Numerical Weather Prediction and Data Assimilation Systems

    NASA Astrophysics Data System (ADS)

    Swadley, S. D.; Baker, N.; Derber, J.; Collard, A.; Hilton, F.; Ruston, B.; Bell, W.; Candy, B.; Kleespies, T. J.

    2009-12-01

    The NPOESS atmospheric sounding functionality will be accomplished using two separate sensor suites, the combined infrared (IR) and microwave (MW) sensor suite (CrIMSS), and the Microwave Imager/Sounder (MIS) instrument. CrIMSS consists of the Cross Track Infrared Sounder (CrIS) and the cross track Advanced Technology Microwave Sounder (ATMS), and is scheduled to fly on the NPOESS Preparatory Project (NPP), and NPOESS operational flight units C1 and C3. The MIS is a conical scanning polarimetric imager and sounder patterned after the heritage WindSat, and DMSP Special Sensor Microwave Imagers and Sounders (SSMI and SSMIS), and is scheduled for flight units C2, C3 and C4. ATMS combines the current operational Advanced Microwave Sounding Unit (AMSU) and the Microwave Humidity Sounder (MHS), but with an additional channel in the 51.76 GHz oxygen absorption region and 3 additional channels in the 165.5 and 183 GHz water vapor absorption band. CrIS is a Fourier Transform Spectrometer and will provide 159 shortwave IR channels, 433 mid-range IR channels, and 713 longwave IR channels. The heritage sensors for CrIS are the NASA Advanced Infrared Sounder (AIRS) and the MetOp-A Infrared Atmospheric Sounding Interferometer (IASI). Both AIRS and IASI are high quality, high spectral resolution sounders which represent a significant improvement in the effective vertical resolution over previous IR sounders. This presentation will give an overview of preparations underway for day-1 monitoring of NPP/NPOESS radiances, and subsequent operational radiance assimilation. These preparations capitalize on experience gained during the pre-launch preparations, sensor calibration/validation and operational assimilation for the heritage sensors. One important step is to use pre-flight sensor channel specifications, noise estimates and knowledge of the antenna patterns, to generate and test proxy NPP/NPOESS sensor observations in existing assimilation systems. Other critical factors for

  3. Interstitial diffuse radiance spectroscopy of gold nanocages and nanorods in bulk muscle tissues.

    PubMed

    Grabtchak, Serge; Montgomery, Logan G; Pang, Bo; Wang, Yi; Zhang, Chao; Li, Zhiyuan; Xia, Younan; Whelan, William M

    2015-01-01

    Radiance spectroscopy was applied to the interstitial detection of localized inclusions containing Au nanocages or nanorods with various concentrations embedded in porcine muscle phantoms. The radiance was quantified using a perturbation approach, which enabled the separation of contributions from the porcine phantom and the localized inclusion, with the inclusion serving as a perturbation probe of photon distributions in the turbid medium. Positioning the inclusion at various places in the phantom allowed for tracking of photons that originated from a light source, passed through the inclusion's location, and reached a detector. The inclusions with high extinction coefficients were able to absorb nearly all photons in the range of 650-900 nm, leading to a spectrally flat radiance signal. This signal could be converted to the relative density of photons incident on the inclusion. Finally, the experimentally measured quantities were expressed via the relative perturbation and arranged into the classical Beer-Lambert law that allowed one to extract the extinction coefficients of various types of Au nanoparticles in both the transmission and back reflection geometries. It was shown that the spatial variation of perturbation could be described as 1/r dependence, where r is the distance between the inclusion and the detector. Due to a larger absorption cross section, Au nanocages produced greater perturbations than Au nanorods of equal particle concentration, indicating a better suitability of Au nanocages as contrast agents for optical measurements in turbid media. Individual measurements from different inclusions were combined into detectability maps.

  4. Improving Forecast Skill by Assimilation of AIRS Cloud Cleared Radiances RiCC

    NASA Technical Reports Server (NTRS)

    Susskind, Joel; Rosenberg, Robert I.; Iredell, Lena

    2015-01-01

    ECMWF, NCEP, and GMAO routinely assimilate radiosonde and other in-situ observations along with satellite IR and MW Sounder radiance observations. NCEP and GMAO use the NCEP GSI Data Assimilation System (DAS).GSI DAS assimilates AIRS, CrIS, IASI channel radiances Ri on a channel-by-channel, case-by-case basis, only for those channels i thought to be unaffected by cloud cover. This test excludes Ri for most tropospheric sounding channels under partial cloud cover conditions. AIRS Version-6 RiCC is a derived quantity representative of what AIRS channel i would have seen if the AIRS FOR were cloud free. All values of RiCC have case-by-case error estimates RiCC associated with them. Our experiments present to the GSI QCd values of AIRS RiCC in place of AIRS Ri observations. GSI DAS assimilates only those values of RiCC it thinks are cloud free. This potentially allows for better coverage of assimilated QCd values of RiCC as compared to Ri.

  5. Factors Affecting Wound Healing

    PubMed Central

    Guo, S.; DiPietro, L.A.

    2010-01-01

    Wound healing, as a normal biological process in the human body, is achieved through four precisely and highly programmed phases: hemostasis, inflammation, proliferation, and remodeling. For a wound to heal successfully, all four phases must occur in the proper sequence and time frame. Many factors can interfere with one or more phases of this process, thus causing improper or impaired wound healing. This article reviews the recent literature on the most significant factors that affect cutaneous wound healing and the potential cellular and/or molecular mechanisms involved. The factors discussed include oxygenation, infection, age and sex hormones, stress, diabetes, obesity, medications, alcoholism, smoking, and nutrition. A better understanding of the influence of these factors on repair may lead to therapeutics that improve wound healing and resolve impaired wounds. PMID:20139336

  6. Factors affecting wound healing.

    PubMed

    Guo, S; Dipietro, L A

    2010-03-01

    Wound healing, as a normal biological process in the human body, is achieved through four precisely and highly programmed phases: hemostasis, inflammation, proliferation, and remodeling. For a wound to heal successfully, all four phases must occur in the proper sequence and time frame. Many factors can interfere with one or more phases of this process, thus causing improper or impaired wound healing. This article reviews the recent literature on the most significant factors that affect cutaneous wound healing and the potential cellular and/or molecular mechanisms involved. The factors discussed include oxygenation, infection, age and sex hormones, stress, diabetes, obesity, medications, alcoholism, smoking, and nutrition. A better understanding of the influence of these factors on repair may lead to therapeutics that improve wound healing and resolve impaired wounds.

  7. Potential for the use of reconstructed IASI radiances in the detection of atmospheric trace gases

    NASA Astrophysics Data System (ADS)

    Atkinson, N. C.; Hilton, F. I.; Illingworth, S. M.; Eyre, J. R.; Hultberg, T.

    2010-07-01

    Principal component (PC) analysis has received considerable attention as a technique for the extraction of meteorological signals from hyperspectral infra-red sounders such as the Infrared Atmospheric Sounding Interferometer (IASI) and the Atmospheric Infrared Sounder (AIRS). In addition to achieving substantial bit-volume reductions for dissemination purposes, the technique can also be used to generate reconstructed radiances in which random instrument noise has been reduced. Studies on PC analysis of hyperspectral infrared sounder data have been undertaken in the context of numerical weather prediction, instrument monitoring and geophysical variable retrieval, as well as data compression. This study examines the potential of PC analysis for chemistry applications. A major concern in the use of PC analysis for chemistry is that the spectral features associated with trace gases may not be well represented in the reconstructed spectra, either due to deficiencies in the training set or due to the limited number of PC scores used in the radiance reconstruction. In this paper we show examples of reconstructed IASI radiances for several trace gases: ammonia, sulphur dioxide, methane and carbon monoxide. It is shown that care must be taken in the selection of spectra for the initial training set: an iterative technique, in which outlier spectra are added to a base training set, gives the best results. For the four trace gases examined, key features of the chemical signatures are retained in the reconstructed radiances, whilst achieving a substantial reduction in instrument noise. A new regional re-transmission service for IASI is scheduled to start in 2010, as part of the EUMETSAT Advanced Retransmission Service (EARS). For this EARS-IASI service it is intended to include PC scores as part of the data stream. The paper describes the generation of the reference eigenvectors for this new service.

  8. Ground-based retrieval of atmospheric temperature, moisture, cloud properties, and aerosols using the Atmospheric Emitted Radiance Interferometer (AERI)

    NASA Astrophysics Data System (ADS)

    Feltz, W.; Turner, D.; Knuteson, R.; Revercomb, H.; Best, F.; Dedecker, R.; Li, J.; Buijs, H.; Clateauneuf, F.; Roy, C.

    The Atmospheric Emitted Radiance Interferometer AERI system measures infrared downwelling radiances at one wavenumber resolution from 3-20 mu m with better than 10-minute temporal resolution The robust and fully automated AERI instruments are monitored in the field via the Internet in near real-time The AERI absolute radiometric accuracy is better than 1 of ambient radiance The calibrated AERI radiances are used to validate high spectral resolution line-by-line model calculations retrieve profiles of atmospheric constituents derive cloud aerosol properties and surface oceanic skin properties The University of Wisconsin -- Madison Space Science and Engineering Center SSEC developed the AERI for use within the United States Department of Energy DOE Atmospheric Radiation Measurement ARM research program DOE ARM has funded the development and installation of eight ground-based AERI systems based in several international locations including Darwin Australia Niger Africa Barrow Alaska and Nauru Island in the South Pacific The AERI systems have shown high reliability including over ten years of continuous operation at Lamont Oklahoma USA The AERI technology has been licensed to ABB Bomem of Quebec City Canada and plans are underway to provide commercial versions of a variety of atmospheric measurement capabilities The most mature and demonstrated capability allows direct retrieval of meteorological information about the vertical structure of temperature and water vapor in the planetary boundary layer PBL 0-3 km New

  9. SU-E-T-470: Beam Performance of the Radiance 330 Proton Therapy System

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Nazaryan, H; Nazaryan, V; Wang, F

    2014-06-01

    Purpose: The ProTom Radiance 330 proton radiotherapy system is a fully functional, compact proton radiotherapy system that provides advanced proton delivery capabilities. It supports three-dimensional beam scanning with energy and intensity modulation. A series of measurements have been conducted to characterize the beam performance of the first installation of the system at the McLaren Proton Therapy Center in Flint, Michigan. These measurements were part of the technical commissioning of the system. Select measurements and results are presented. Methods: The Radiance 330 proton beam energy range is 70–250 MeV for treatment, and up to 330 MeV for proton tomography and radiography.more » Its 3-D scanning capability, together with a small beam emittance and momentum spread, provides a highly efficient beam delivery. During the technical commissioning, treatment plans were created to deliver uniform maps at various energies to perform Gamma Index analysis. EBT3 Gafchromic films were irradiated using the Planned irradiation maps. Bragg Peak chamber was used to test the dynamic range during a scan in one layer for high (250 MeV) and Low (70 MeV) energies. The maximum and minimum range, range adjustment and modulation, distal dose falloff (80%–20%), pencil beam spot size, spot placement accuracy were also measured. The accuracy testing included acquiring images, image registration, receiving correction vectors and applying the corrections to the robotic patient positioner. Results: Gamma Index analysis of the Treatment Planning System (TPS) data vs. Measured data showed more than 90% of points within (3%, 3mm) for the maps created by the TPS. At Isocenter Beam Size (One sigma) < 3mm at highest energy (250 MeV) in air. Beam delivery was within 0.6 mm of the intended target at the entrance and the exit of the beam, through the phantom. Conclusion: The Radiance 330 Beam Performance Measurements have confirmed that the system operates as designed with excellent

  10. Factors Affecting Sign Retroreflectivity : final report.

    DOT National Transportation Integrated Search

    2001-01-01

    This study was undertaken to better understand the factors that may affect road sign retroreflectivity, specifically age and physical orientation. A better understanding of these factors could provide guidance to ODOT in managing its inventory of roa...

  11. Observed Spectral Invariant Behavior of Zenith Radiance in the Transition Zone Between Cloud-Free and Cloudy Regions

    NASA Technical Reports Server (NTRS)

    Marshak, A.; Knyazikhin, Y.; Chiu, C.; Wiscombe, W.

    2010-01-01

    The Atmospheric Radiation Measurement Program's (ARM) new Shortwave Spectrometer (SWS) looks straight up and measures zenith radiance at 418 wavelengths between 350 and 2200 nm. Because of its 1-sec sampling resolution, the SWS provides a unique capability to study the transition zone between cloudy and clear sky areas. A surprising spectral invariant behavior is found between ratios of zenith radiance spectra during the transition from cloudy to cloud-free atmosphere. This behavior suggests that the spectral signature of the transition zone is a linear mixture between the two extremes (definitely cloudy and definitely clear). The weighting function of the linear mixture is found to be a wavelength-independent characteristic of the transition zone. It is shown that the transition zone spectrum is fully determined by this function and zenith radiance spectra of clear and cloudy regions. This new finding may help us to better understand and quantify such physical phenomena as humidification of aerosols in the relatively moist cloud environment and evaporation and activation of cloud droplets.

  12. Contributed Review: Absolute spectral radiance calibration of fiber-optic shock-temperature pyrometers using a coiled-coil irradiance standard lamp

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Fat’yanov, O. V., E-mail: fatyan1@gps.caltech.edu; Asimow, P. D., E-mail: asimow@gps.caltech.edu

    2015-10-15

    We describe an accurate and precise calibration procedure for multichannel optical pyrometers such as the 6-channel, 3-ns temporal resolution instrument used in the Caltech experimental geophysics laboratory. We begin with a review of calibration sources for shock temperatures in the 3000-30 000 K range. High-power, coiled tungsten halogen standards of spectral irradiance appear to be the only practical alternative to NIST-traceable tungsten ribbon lamps, which are no longer available with large enough calibrated area. However, non-uniform radiance complicates the use of such coiled lamps for reliable and reproducible calibration of pyrometers that employ imaging or relay optics. Careful analysis of documentedmore » methods of shock pyrometer calibration to coiled irradiance standard lamps shows that only one technique, not directly applicable in our case, is free of major radiometric errors. We provide a detailed description of the modified Caltech pyrometer instrument and a procedure for its absolute spectral radiance calibration, accurate to ±5%. We employ a designated central area of a 0.7× demagnified image of a coiled-coil tungsten halogen lamp filament, cross-calibrated against a NIST-traceable tungsten ribbon lamp. We give the results of the cross-calibration along with descriptions of the optical arrangement, data acquisition, and processing. We describe a procedure to characterize the difference between the static and dynamic response of amplified photodetectors, allowing time-dependent photodiode correction factors for spectral radiance histories from shock experiments. We validate correct operation of the modified Caltech pyrometer with actual shock temperature experiments on single-crystal NaCl and MgO and obtain very good agreement with the literature data for these substances. We conclude with a summary of the most essential requirements for error-free calibration of a fiber-optic shock-temperature pyrometer using a high-power coiled tungsten

  13. Interstitial diffuse radiance spectroscopy of gold nanocages and nanorods in bulk muscle tissues

    PubMed Central

    Grabtchak, Serge; Montgomery, Logan G; Pang, Bo; Wang, Yi; Zhang, Chao; Li, Zhiyuan; Xia, Younan; Whelan, William M

    2015-01-01

    Radiance spectroscopy was applied to the interstitial detection of localized inclusions containing Au nanocages or nanorods with various concentrations embedded in porcine muscle phantoms. The radiance was quantified using a perturbation approach, which enabled the separation of contributions from the porcine phantom and the localized inclusion, with the inclusion serving as a perturbation probe of photon distributions in the turbid medium. Positioning the inclusion at various places in the phantom allowed for tracking of photons that originated from a light source, passed through the inclusion’s location, and reached a detector. The inclusions with high extinction coefficients were able to absorb nearly all photons in the range of 650–900 nm, leading to a spectrally flat radiance signal. This signal could be converted to the relative density of photons incident on the inclusion. Finally, the experimentally measured quantities were expressed via the relative perturbation and arranged into the classical Beer–Lambert law that allowed one to extract the extinction coefficients of various types of Au nanoparticles in both the transmission and back reflection geometries. It was shown that the spatial variation of perturbation could be described as 1/r dependence, where r is the distance between the inclusion and the detector. Due to a larger absorption cross section, Au nanocages produced greater perturbations than Au nanorods of equal particle concentration, indicating a better suitability of Au nanocages as contrast agents for optical measurements in turbid media. Individual measurements from different inclusions were combined into detectability maps. PMID:25709450

  14. Use of the Polarized Radiance Distribution Camera System in the RADYO Program

    DTIC Science & Technology

    2011-01-28

    characterization and validation of a high dynamic range radiance camera", Ocean Optics XX, Anchorage, Ak., October 2010. POSTER G. Zibordi and K. J. Voss...on light in the ocean", Submitted to Physics Today, Dec 2010. H. Zhang and K. J. Voss, "On Hapke photometric model predictions on reflectance of

  15. Relationships between chlorophyll density and ocean radiance as measured by U2/OCS: Algorithms, examples and comparison

    NASA Technical Reports Server (NTRS)

    Kim, H. H.; Hart, W. D.

    1983-01-01

    An ocean atmosphere radiative transfer process computation method which is suitable for determining lower boundary ocean albedo and other radiation components from spectral measurements of upwelling radiance taken from a high altitude platform is described. The method was applied to a set of color scanner data taken from slope water of the South Atlantic Bight to determine the influence of cholorophyll-a pigments in the sea on the ratio of upwelling radiance to down welling irradiance as a function of wavelength. The resulting chlorophyll concentrations are compared with measurements made by ships stationed along the flight path.

  16. Aerosol Properties Derived from Airborne Sky Radiance and Direct Beam Measurements in Recent NASA and DoE Field Campaigns

    NASA Technical Reports Server (NTRS)

    Redemann, J.; Flynn, C. J.; Shinozuka, Y.; Russell, P. B.; Kacenelenbogen, M.; Segal-Rosenheimer, M.; Livingston, J. M.; Schmid, B.; Dunagan, S. E.; Johnson, R. R.; hide

    2014-01-01

    The AERONET (AErosol RObotic NETwork) ground-based suite of sunphotometers provides measurements of spectral aerosol optical depth (AOD), precipitable water and spectral sky radiance, which can be inverted to retrieve aerosol microphysical properties that are critical to assessments of aerosol-climate interactions. Because of data quality criteria and sampling constraints, there are significant limitations to the temporal and spatial coverage of AERONET data and their representativeness for global aerosol conditions.The 4STAR (Spectrometer for Sky-Scanning, Sun-Tracking Atmospheric Research) instrument, jointly developed by NASA Ames and PNNL (Pacific Northwest National Laboratory) with NASA Goddard collaboration, combines airborne sun tracking and AERONET-like sky scanning with spectroscopic detection. Being an airborne instrument, 4STAR has the potential to fill gaps in the AERONET data set. The 4STAR instrument operated successfully in the SEAC4RS (Studies of Emissions and Atmospheric Composition, Clouds and Climate Coupling by Regional Surveys) experiment in Aug./Sep. 2013 aboard the NASA DC-8 and in the DoE (Department of Energy)-sponsored TCAP (Two Column Aerosol Project, July 2012 & Feb. 2013) experiment aboard the DoE G-1 aircraft. 4STAR provided direct beam measurements of hyperspectral AOD, columnar trace gas retrievals (H2O, O3, NO2), and the first ever airborne hyperspectral sky radiance scans, which can be inverted to yield the same products as AERONET ground-based observations. In this presentation, we provide an overview of the new 4STAR capabilities, with an emphasis on 26 high-quality sky radiance measurements carried out by 4STAR in SEAC4RS. We compare collocated 4STAR and AERONET sky radiances, as well as their retrievals of aerosol microphysical properties for a subset of the available case studies. We summarize the particle property and air-mass characterization studies made possible by the combined 4STAR direct beam and sky radiance

  17. Retrievals of atmospheric parameters from radiances obtained by the Juno Microwave Radiometer

    NASA Astrophysics Data System (ADS)

    Li, C.; Ingersoll, A. P.; Janssen, M. A.

    2016-12-01

    The Juno microwave radiometer (MWR) makes a north-south scan of Jupiter on every perijove pass of the spacecraft (Fig. 1). The planet is observed in six channels, at wavelengths ranging from 1.3 cm to 50 cm, the peaks of whose weighting functions range from 0.6 bars to 30 bars, respectively. Within 25 degrees of the equator each latitude band 1 degree wide is observed at 5-10 different emission angles. Intermediate processing involves conversion of electrical signals into radiances, subtraction of the side lobe contributions, and deconvolution to achieve maximum spatial resolution. After that, one wants to convert the radiances into physical parameters of the atmosphere, all as functions of latitude. The two main goals of the MWR are (1) to determine the global water and ammonia abundances and (2) to document the latitude variations of water, ammonia, and temperature in the subcloud regions, in effect, to observe the deep Jovian weather. Prior probability is based on the Galileo probe results at 6 degrees north latitude, VLA maps at wavelengths shorter than 7 cm, and moist adiabats calculated from assumed deep abundances of water and ammonia. A complication is that ammonia dominates the microwave opacity, and water is detectable mainly through its effect on the temperature profile and the slope of the moist adiabat. MCMC analysis of synthetic data suggests that the radiances and limb-darkening parameters contain at most 4 pieces of information about the atmosphere at each latitude. Choosing the right parameters is the heart of the effort, and we will report on testing the choices using synthetic and real data. If we have preliminary results concerning objectives (1) and (2) above, we will share them.

  18. RADIANCE: An automated, enterprise-wide solution for archiving and reporting CT radiation dose estimates.

    PubMed

    Cook, Tessa S; Zimmerman, Stefan L; Steingall, Scott R; Maidment, Andrew D A; Kim, Woojin; Boonn, William W

    2011-01-01

    There is growing interest in the ability to monitor, track, and report exposure to radiation from medical imaging. Historically, however, dose information has been stored on an image-based dose sheet, an arrangement that precludes widespread indexing. Although scanner manufacturers are beginning to include dose-related parameters in the Digital Imaging and Communications in Medicine (DICOM) headers of imaging studies, there remains a vast repository of retrospective computed tomographic (CT) data with image-based dose sheets. Consequently, it is difficult for imaging centers to monitor their dose estimates or participate in the American College of Radiology (ACR) Dose Index Registry. An automated extraction software pipeline known as Radiation Dose Intelligent Analytics for CT Examinations (RADIANCE) has been designed that quickly and accurately parses CT dose sheets to extract and archive dose-related parameters. Optical character recognition of information in the dose sheet leads to creation of a text file, which along with the DICOM study header is parsed to extract dose-related data. The data are then stored in a relational database that can be queried for dose monitoring and report creation. RADIANCE allows efficient dose analysis of CT examinations and more effective education of technologists, radiologists, and referring physicians regarding patient exposure to radiation at CT. RADIANCE also allows compliance with the ACR's dose reporting guidelines and greater awareness of patient radiation dose, ultimately resulting in improved patient care and treatment.

  19. A neural network method to correct bidirectional effects in water-leaving radiance

    NASA Astrophysics Data System (ADS)

    Fan, Yongzhen; Li, Wei; Voss, Kenneth J.; Gatebe, Charles K.; Stamnes, Knut

    2017-02-01

    The standard method to convert the measured water-leaving radiances from the observation direction to the nadir direction developed by Morel and coworkers requires knowledge of the chlorophyll concentration (CHL). Also, the standard method was developed for open ocean water, which makes it unsuitable for turbid coastal waters. We introduce a neural network method to convert the water-leaving radiance (or the corresponding remote sensing reflectance) from the observation direction to the nadir direction. This method does not require any prior knowledge of the water constituents or the inherent optical properties (IOPs). This method is fast, accurate and can be easily adapted to different remote sensing instruments. Validation using NuRADS measurements in different types of water shows that this method is suitable for both open ocean and coastal waters. In open ocean or chlorophyll-dominated waters, our neural network method produces corrections similar to those of the standard method. In turbid coastal waters, especially sediment-dominated waters, a significant improvement was obtained compared to the standard method.

  20. Validation of SCIAMACHY and TOMS UV Radiances Using Ground and Space Observations

    NASA Technical Reports Server (NTRS)

    Hilsenrath, E.; Bhartia, P. K.; Bojkov, B. R.; Kowalewski, M.; Labow, G.; Ahmad, Z.

    2004-01-01

    Verification of a stratospheric ozone recovery remains a high priority for environmental research and policy definition. Models predict an ozone recovery at a much lower rate than the measured depletion rate observed to date. Therefore improved precision of the satellite and ground ozone observing systems are required over the long term to verify its recovery. We show that validation of satellite radiances from space and from the ground can be a very effective means for correcting long term drifts of backscatter type satellite measurements and can be used to cross calibrate all B W instruments in orbit (TOMS, SBW/2, GOME, SCIAMACHY, OM, GOME-2, OMPS). This method bypasses the retrieval algorithms used for both satellite and ground based measurements that are normally used to validate and correct the satellite data. Radiance comparisons employ forward models and are inherently more accurate than inverse (retrieval) algorithms. This approach however requires well calibrated instruments and an accurate radiative transfer model that accounts for aerosols. TOMS and SCIAMACHY calibrations are checked to demonstrate this method and to demonstrate applicability for long term trends.

  1. Influence of dust on cometary radiance spectra infered from various models of Comet 67P/Churyumov-Gerasimenko

    NASA Astrophysics Data System (ADS)

    Blecka, M. I.; Coradini, A.; Capaccioni, F.; Capria, M. T.; De sanctis, M.

    2011-12-01

    The work we present deals with the spectrometric measurements of VIRTIS instrument of the Rosetta mission to the Comet 67P/Churyumov-Gerasimenko (C-G). The dust important constituent of cometary environment is always present on the surface of the nucleus and in the inner coma. The cometary spectra are strongly affected by the processes taking place in the coma and by the structure and composition of cometary materials. The particles of the dust , illuminated by solar light, scatter, absorb and emit radiation. The reflected and the emitted radiation are transmitted through the coma region before being collected by instruments such as VIRTIS .The reflection, absorption, scattering, and emission processes depend on the Comet-Sun geometry and on the thermal state of the nucleus. The main purposes of the paper are: 1) short review of the published models related to the topic of presence and distribution of the solid particles in the inner coma of the Comet 67/P (C-G) 2) description of numerical calculations done by means of an radiation transfer model and comparison the simulated radiance spectra 3) discussion on influence the geometry of the measurements and the particular parameters of the thermal models taken in consideration. 4) demonstration of simulated spectra of the total directional radiance which can help to recognize the optical characteristics of constituents of the environment of Comet 67P/(C-G) References J.Agarwal; M.Müller, G.Eberhard, Dust Environment Modelling of Comet 67P/Churyumov-Gerasimenko; Space Science Reviews, 128,1-4,2007 M. I. Blecka, M.T. Capria, A. Coradini, M.C. De Sanctis; Numerical simulations of the radiance from the Comet 46P/Wirtanen in the Ivarious configuration of the measurements during "Rosetta" Mission Adv. Space Res.31,12, 2501-2510,2003 M.C.De Sanctis, J.Lasue, M.T.Capria, G. Magni, D. Turrini, A. Coradini, Shape and obliquity effects on the thermal evolution of the Rosetta target 67P/Churyumov-Gerasimenko cometary nucleus

  2. Laboratory measurements of radiance and reflectance spectra of dilute secondary-treated sewage sludge

    NASA Technical Reports Server (NTRS)

    Witte, W. G.; Usry, J. W.; Whitlock, C. H.; Gurganus, E. A.

    1977-01-01

    The National Aeronautics and Space Administration (NASA), in cooperation with the Environmental Protection Agency (EPA) and the National Oceanic and Atmospheric Administration (NOAA), conducted a research program to evaluate the feasibility of remotely monitoring ocean dumping of waste products such as acid and sewage sludge. One aspect of the research program involved the measurements of upwelled spectral signatures for sewage-sludge mixtures of different concentrations in an 11600-liter tank. This paper describes the laboratory arrangement and presents radiance and reflectance spectra in the visible and near-infrared ranges for concentrations ranging from 9.7 to 180 ppm of secondary-treated sewage sludge mixed with two types of base water. Results indicate that upwelled radiance varies in a near-linear manner with concentration and that the sludge has a practically flat signal response between 420 and 970 nm. Reflectance spectra were obtained for the sewage-sludge mixtures at all wavelengths and concentrations.

  3. Mesoscale Gravity Wave Variances from AMSU-A Radiances

    NASA Technical Reports Server (NTRS)

    Wu, Dong L.

    2004-01-01

    A variance analysis technique is developed here to extract gravity wave (GW) induced temperature fluctuations from NOAA AMSU-A (Advanced Microwave Sounding Unit-A) radiance measurements. By carefully removing the instrument/measurement noise, the algorithm can produce reliable GW variances with the minimum detectable value as small as 0.1 K2. Preliminary analyses with AMSU-A data show GW variance maps in the stratosphere have very similar distributions to those found with the UARS MLS (Upper Atmosphere Research Satellite Microwave Limb Sounder). However, the AMSU-A offers better horizontal and temporal resolution for observing regional GW variability, such as activity over sub-Antarctic islands.

  4. Acquisition and analysis of coastal ground-truth data for correlation with ERTS-1 imagery. [surface radiance data for Santa Monica Bay and Santa Barbara Channel

    NASA Technical Reports Server (NTRS)

    Anikouchine, W. A. (Principal Investigator)

    1973-01-01

    The author has identified the following significant results. Radiance profiles drawn along cruise tracks have been examined for use in correlating digital radiance levels with ground truth data. Preliminary examination results are encouraging. Adding weighted levels from the 4 MSS bands appears to enhance specular surface reflections while rendering sensor noise white. Comparing each band signature to the added specular signature ought to enhance non-specular effects caused by ocean turbidity. Preliminary examination of radiance profiles and ground truth turbidity measurements revealed substantial correlation.

  5. A New Technique for Retrieval of Tropospheric and Stratospheric Ozone Profiles using Sky Radiance Measurements at Multiple View Angles: Application to a Brewer Spectrometer

    NASA Technical Reports Server (NTRS)

    Tzortziou, Maria; Krotkov, Nickolay A.; Cede, Alexander; Herman, Jay R.; Vasilkov, Alexander

    2008-01-01

    This paper describes and applies a new technique for retrieving diurnal variability in tropospheric ozone vertical distribution using ground-based measurements of ultraviolet sky radiances. The measured radiances are obtained by a polarization-insensitive modified Brewer double spectrometer located at Goddard Space Flight Center, in Greenbelt, Maryland, USA. Results demonstrate that the Brewer angular (0-72deg viewing zenith angle) and spectral (303-320 nm) measurements of sky radiance in the solar principal plane provide sufficient information to derive tropospheric ozone diurnal variability. In addition, the Brewer measurements provide stratospheric ozone vertical distributions at least twice per day near sunrise and sunset. Frequent measurements of total column ozone amounts from direct-sun observations are used as constraints in the retrieval. The vertical ozone profile resolution is shown in terms of averaging kernels to yield at least four points in the troposphere-low stratosphere, including good information in Umkehr layer 0 (0-5 km). The focus of this paper is on the derivation of stratospheric and tropospheric ozone profiles using both simulated and measured radiances. We briefly discuss the necessary modifications of the Brewer spectrometer that were used to eliminate instrumental polarization sensitivity so that accurate sky radiances can be obtained in the presence of strong Rayleigh scattering and aerosols. The results demonstrate that including a site-specific and time-dependent aerosol correction, based on Brewer direct-sun observations of aerosol optical thickness, is critical to minimize the sky radiance residuals as a function of observing angle in the optimal estimation inversion algorithm and improve the accuracy of the retrieved ozone profile.

  6. Age Learning Factors Affecting Pilot Education.

    ERIC Educational Resources Information Center

    Torbert, Brison

    This document, intended for pilot education and flight safety specialists, consists chiefly of a review of the literature on physiological factors that affect pilot education and an examination of environmental factors that should be scrutinized in order to improve the effectiveness of aviation learning facilities. The physiological factors…

  7. A fast code for channel limb radiances with gas absorption and scattering in a spherical atmosphere

    NASA Astrophysics Data System (ADS)

    Eluszkiewicz, Janusz; Uymin, Gennady; Flittner, David; Cady-Pereira, Karen; Mlawer, Eli; Henderson, John; Moncet, Jean-Luc; Nehrkorn, Thomas; Wolff, Michael

    2017-05-01

    We present a radiative transfer code capable of accurately and rapidly computing channel limb radiances in the presence of gaseous absorption and scattering in a spherical atmosphere. The code has been prototyped for the Mars Climate Sounder measuring limb radiances in the thermal part of the spectrum (200-900 cm-1) where absorption by carbon dioxide and water vapor and absorption and scattering by dust and water ice particles are important. The code relies on three main components: 1) The Gauss Seidel Spherical Radiative Transfer Model (GSSRTM) for scattering, 2) The Planetary Line-By-Line Radiative Transfer Model (P-LBLRTM) for gas opacity, and 3) The Optimal Spectral Sampling (OSS) for selecting a limited number of spectral points to simulate channel radiances and thus achieving a substantial increase in speed. The accuracy of the code has been evaluated against brute-force line-by-line calculations performed on the NASA Pleiades supercomputer, with satisfactory results. Additional improvements in both accuracy and speed are attainable through incremental changes to the basic approach presented in this paper, which would further support the use of this code for real-time retrievals and data assimilation. Both newly developed codes, GSSRTM/OSS for MCS and P-LBLRTM, are available for additional testing and user feedback.

  8. Preliminary Results from an Assimilation of Saharan Dust Using TOMS Radiances and the GOCART Model

    NASA Technical Reports Server (NTRS)

    Weaver, C. J.; daSilva, Arlindo; Ginoux, Paul; Torres, Omar; Einaudi, Franco (Technical Monitor)

    2000-01-01

    At NASA Goddard we are developing a global aerosol data assimilation system that combines advances in remote sensing and modeling of atmospheric aerosols. The goal is to provide high resolution, 3-D aerosol distributions to the research community. Our first step is to develop a simple assimilation system for Saharan mineral aerosol. The Goddard Chemistry and Aerosol Radiation model (GOCART) provides accurate 3-D mineral aerosol size distributions. Surface mobilization, wet and dry deposition, convective and long-range transport are all driven by assimilated fields from the Goddard Earth Observing System Data Assimilation System, GEOS-DAS. Our version of GOCART transports sizes from .08-10 microns and only simulates Saharan dust. We draw the assimilation to two observables in this study: the TOMS aerosol index (Al) which is directly related to the ratio of the 340 and 380 radiances and the 380 radiance alone. The forward model that simulates the observables requires the aerosol optical thickness, the single scattering albedo and the height of the aerosol layer from the GOCART fields. The forward model also requires a refractive index for the dust. We test three index values to see which best fits the TOMS observables. These are 1) for Saharan dust reported by Patterson, 2) for a mixture of Saharan dust and a highly reflective material (sea salt or sulfate) and 3) for pure illite. The assimilation works best assuming either pure illite or the dust mixture. Our assimilation cycle first determines values of the aerosol index (Al) and the radiance at 380 nm based on the GOCART aerosol fields. Differences between the observed and GOCART model calculated Al and 380 nm radiance are first analyzed horizontally using the Physical-space Statistical Analysis System (PSAS). A quasi-Newton iteration is then performed to produce analyzed 3D aerosol fields according to parameterized background and observation error covariances. We only assimilate observations into the the GOCART

  9. Added Value of Assimilating Himawari-8 AHI Water Vapor Radiances on Analyses and Forecasts for "7.19" Severe Storm Over North China

    NASA Astrophysics Data System (ADS)

    Wang, Yuanbing; Liu, Zhiquan; Yang, Sen; Min, Jinzhong; Chen, Liqiang; Chen, Yaodeng; Zhang, Tao

    2018-04-01

    Himawari-8 is the first launched and operational new-generation geostationary meteorological satellite. The Advanced Himawari Imager (AHI) on board Himawari-8 provides continuous high-resolution observations of severe weather phenomena in space and time. In this study, the capability to assimilate AHI radiances has been developed within the Weather Research and Forecasting (WRF) model's data assimilation system. As the first attempt to assimilate AHI using WRF data assimilation at convective scales, the added value of hourly AHI clear-sky radiances from three water vapor channels on convection-permitting (3 km) analyses and forecasts of the "7.19" severe rainstorm that occurred over north China during 18-21 July 2016 was investigated. Analyses were produced hourly, and 24 h forecasts were produced every 6 h. The results showed that improved wind and humidity fields were obtained in analyses and forecasts verified against conventional observations after assimilating AHI water vapor radiances when compared to the control experiment which assimilated only conventional observations. It was also found that the assimilation of AHI water vapor radiances had a clearly positive impact on the rainfall forecast for the first 6 h lead time, especially for heavy rainfall exceeding 100 mm when verified against the observed rainfall. Furthermore, the horizontal and vertical distribution of features in the moisture fields were improved after assimilating AHI water vapor radiances, eventually contributing to a better forecast of the severe rainstorm.

  10. Determining the Performance of Fluorescence Molecular Imaging Devices using Traceable Working Standards with SI Units of Radiance

    PubMed Central

    Zhu, Banghe; Rasmussen, John C.; Litorja, Maritoni

    2017-01-01

    To date, no emerging preclinical or clinical near-infrared fluorescence (NIRF) imaging devices for non-invasive and/or surgical guidance have their performances validated on working standards with SI units of radiance that enable comparison or quantitative quality assurance. In this work, we developed and deployed a methodology to calibrate a stable, solid phantom for emission radiance with units of mW · sr−1 · cm−2 for use in characterizing the measurement sensitivity of ICCD and IsCMOS detection, signal-to-noise ratio, and contrast. In addition, at calibrated radiances, we assess transverse and lateral resolution of ICCD and IsCMOS camera systems. The methodology allowed determination of superior SNR of the ICCD over the IsCMOS camera system and superior resolution of the IsCMOS over the ICCD camera system. Contrast depended upon the camera settings (binning and integration time) and gain of intensifier. Finally, because of architecture of CMOS and CCD camera systems resulting in vastly different performance, we comment on the utility of these systems for small animal imaging as well as clinical applications for non-invasive and surgical guidance. PMID:26552078

  11. A theory for the retrieval of virtual temperature from winds, radiances and the equations of fluid dynamics

    NASA Technical Reports Server (NTRS)

    Tzvi, G. C.

    1986-01-01

    A technique to deduce the virtual temperature from the combined use of the equations of fluid dynamics, observed wind and observed radiances is described. The wind information could come from ground-based sensitivity very high frequency (VHF) Doppler radars and/or from space-borne Doppler lidars. The radiometers are also assumed to be either space-borne and/or ground-based. From traditional radiometric techniques the vertical structure of the temperature can be estimated only crudely. While it has been known for quite some time that the virtual temperature could be deduced from wind information only, such techniques had to assume the infallibility of certain diagnostic relations. The proposed technique is an extension of the Gal-Chen technique. It is assumed that due to modeling uncertainties the equations of fluid dynamics are satisfied only in the least square sense. The retrieved temperature, however, is constrained to reproduce the observed radiances. It is shown that the combined use of the three sources of information (wind, radiances and fluid dynamical equations) can result in a unique determination of the vertical temperature structure with spatial and temporal resolution comparable to that of the observed wind.

  12. Combining the AIRS, CrIS and IASI Radiance Records for Climate Level Retrievals

    NASA Astrophysics Data System (ADS)

    Strow, L. L.

    2016-12-01

    The AIRS record is now 14+ years long, and with the addition of CrIS should provide a 30+ year long hyperspectral radiance record that can be supplemented with another two times in the diurnal cycle with IASI starting in 2007. The stability of these sensors can be established by comparisons to CO2 variability and to tropical sea surface temperature trends. At present the observed stabilities are much better than climate requirements of 0.01/year. SNO observations indicate radiometric agreement among these sensors of 0.1 - 0.3K before any empirical adjustments. A 1-year set of SNO overlaps have statistical uncertainties of less than 0.01K between these three sensors. Moreover, we show that IASI can be used as a transfer standard between AIRS and CrIS (or between CrIS-1 and CrIS-2) should there be a gap in overlap of sensors in the PM orbit. We have done these SNO comparisons by converting AIRS and IASI spectral to the CrIS instrument lineshape (ILS). Achieving climate quality retrievals, trends, and anomalies of temperature and humidity is non-trivial and requires error characterization (not validation) that to date has not been done with single-footprint hyperspectral sensor retrievals. We suggest that the infrared hyperspectral community utilize a common ILS radiance product as a first-step in achieving climate-quality retrievals in order to remove uncertainties in differential instrument sensitivies and in different forward radiative transfer models. We propose a very different approach for Level 3 (climate) products where anomalies and trends (one of the main products of interest to the climate community) are derived directly from Level 3 radiance products, giving far superior error traceability and retrieval regularization in the vertical. Tempertature and humidity trends and anomalies for 14-years of AIRS will be presented and compared to those provided by ERA-Interim, AIRS Level3 data, and microwave sensors. A significant advantage of this approach, which

  13. A study of photon propagation in free-space based on hybrid radiosity-radiance theorem.

    PubMed

    Chen, Xueli; Gao, Xinbo; Qu, Xiaochao; Liang, Jimin; Wang, Lin; Yang, Da'an; Garofalakis, Anikitos; Ripoll, Jorge; Tian, Jie

    2009-08-31

    Noncontact optical imaging has attracted increasing attention in recent years due to its significant advantages on detection sensitivity, spatial resolution, image quality and system simplicity compared with contact measurement. However, photon transport simulation in free-space is still an extremely challenging topic for the complexity of the optical system. For this purpose, this paper proposes an analytical model for photon propagation in free-space based on hybrid radiosity-radiance theorem (HRRT). It combines Lambert's cosine law and the radiance theorem to handle the influence of the complicated lens and to simplify the photon transport process in the optical system. The performance of the proposed model is evaluated and validated with numerical simulations and physical experiments. Qualitative comparison results of flux distribution at the detector are presented. In particular, error analysis demonstrates the feasibility and potential of the proposed model for simulating photon propagation in free-space.

  14. Environmental Factors Affecting Preschoolers' Motor Development

    ERIC Educational Resources Information Center

    Venetsanou, Fotini; Kambas, Antonis

    2010-01-01

    The process of development occurs according to the pattern established by the genetic potential and also by the influence of environmental factors. The aim of the present study was to focus on the main environmental factors affecting motor development. The review of the literature revealed that family features, such as socioeconomic status,…

  15. Aerosol, Cloud and Trace Gas Observations Derived from Airborne Hyperspectral Radiance and Direct Beam Measurements in Recent Field Campaigns

    NASA Technical Reports Server (NTRS)

    Redemann, J.; Flynn, C. J.; Shinozuka, Y.; Kacenelenbogen, M.; Segal-Rosenheimer, M.; LeBlanc, S.; Russell, P. B.; Livingston, J. M.; Schmid, B.; Dunagan, S. E.; hide

    2014-01-01

    The AERONET (AErosol RObotic NETwork) ground-based suite of sunphotometers provides measurements of spectral aerosol optical depth (AOD), precipitable water and spectral sky radiance, which can be inverted to retrieve aerosol microphysical properties that are critical to assessments of aerosol-climate interactions. Because of data quality criteria and sampling constraints, there are significant limitations to the temporal and spatial coverage of AERONET data and their representativeness for global aerosol conditions. The 4STAR (Spectrometer for Sky-Scanning, Sun-Tracking Atmospheric Research) instrument, jointly developed by NASA Ames and PNNL with NASA Goddard collaboration, combines airborne sun tracking and AERONET-like sky scanning with spectroscopic detection. Being an airborne instrument, 4STAR has the potential to fill gaps in the AERONET data set. Dunagan et al. [2013] present results establishing the performance of the instrument, along with calibration, engineering flight test, and preliminary scientific field data. The 4STAR instrument operated successfully in the SEAC4RS [Studies of Emissions and Atmospheric Composition, Clouds and Climate Coupling by Regional Surveys] experiment in Aug./Sep. 2013 aboard the NASA DC-8 and in the DoE [Department of Energy]-sponsored TCAP [Two Column Aerosol Project, July 2012 & Feb. 2013] experiment aboard the DoE G-1 aircraft (Shinozuka et al., 2013), and acquired a wealth of data in support of mission objectives on all SEAC4RS and TCAP research flights. 4STAR provided direct beam measurements of hyperspectral AOD, columnar trace gas retrievals (H2O, O3, NO2; Segal-Rosenheimer et al., 2014), and the first ever airborne hyperspectral sky radiance scans, which can be inverted to yield the same products as AERONET ground-based observations. In addition, 4STAR measured zenith radiances underneath cloud decks for retrievals of cloud optical depth and effective diameter. In this presentation, we provide an overview of the new

  16. Measurements of downwelling far-infrared radiance during the RHUBC-II campaign at Cerro Toco, Chile and comparisons with line-by-line radiative transfer calculations

    NASA Astrophysics Data System (ADS)

    Mast, Jeffrey C.; Mlynczak, Martin G.; Cageao, Richard P.; Kratz, David P.; Latvakoski, Harri; Johnson, David G.; Turner, David D.; Mlawer, Eli J.

    2017-09-01

    Downwelling radiances at the Earth's surface measured by the Far-Infrared Spectroscopy of the Troposphere (FIRST) instrument in an environment with integrated precipitable water (IPW) as low as 0.03 cm are compared with calculated spectra in the far-infrared and mid-infrared. FIRST (a Fourier transform spectrometer) was deployed from August through October 2009 at 5.38 km MSL on Cerro Toco, a mountain in the Atacama Desert of Chile. There FIRST took part in the Radiative Heating in Unexplored Bands Campaign Part 2 (RHUBC-II), the goal of which is the assessment of water vapor spectroscopy. Radiosonde water vapor and temperature vertical profiles are input into the Atmospheric and Environmental Research (AER) Line-by-Line Radiative Transfer Model (LBLRTM) to compute modeled radiances. The LBLRTM minus FIRST residual spectrum is calculated to assess agreement. Uncertainties (1-σ) in both the measured and modeled radiances are also determined. Measured and modeled radiances nearly all agree to within combined (total) uncertainties. Features exceeding uncertainties can be corrected into the combined uncertainty by increasing water vapor and model continuum absorption, however this may not be necessary due to 1-σ uncertainties (68% confidence). Furthermore, the uncertainty in the measurement-model residual is very large and no additional information on the adequacy of current water vapor spectral line or continuum absorption parameters may be derived. Similar future experiments in similarly cold and dry environments will require absolute accuracy of 0.1% of a 273 K blackbody in radiance and water vapor accuracy of ∼3% in the profile layers contributing to downwelling radiance at the surface.

  17. Nutritional Factors Affecting Adult Neurogenesis and Cognitive Function.

    PubMed

    Poulose, Shibu M; Miller, Marshall G; Scott, Tammy; Shukitt-Hale, Barbara

    2017-11-01

    Adult neurogenesis, a complex process by which stem cells in the hippocampal brain region differentiate and proliferate into new neurons and other resident brain cells, is known to be affected by many intrinsic and extrinsic factors, including diet. Neurogenesis plays a critical role in neural plasticity, brain homeostasis, and maintenance in the central nervous system and is a crucial factor in preserving the cognitive function and repair of damaged brain cells affected by aging and brain disorders. Intrinsic factors such as aging, neuroinflammation, oxidative stress, and brain injury, as well as lifestyle factors such as high-fat and high-sugar diets and alcohol and opioid addiction, negatively affect adult neurogenesis. Conversely, many dietary components such as curcumin, resveratrol, blueberry polyphenols, sulforaphane, salvionic acid, polyunsaturated fatty acids (PUFAs), and diets enriched with polyphenols and PUFAs, as well as caloric restriction, physical exercise, and learning, have been shown to induce neurogenesis in adult brains. Although many of the underlying mechanisms by which nutrients and dietary factors affect adult neurogenesis have yet to be determined, nutritional approaches provide promising prospects to stimulate adult neurogenesis and combat neurodegenerative diseases and cognitive decline. In this review, we summarize the evidence supporting the role of nutritional factors in modifying adult neurogenesis and their potential to preserve cognitive function during aging. © 2017 American Society for Nutrition.

  18. Acceleration of the matrix multiplication of Radiance three phase daylighting simulations with parallel computing on heterogeneous hardware of personal computer

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Zuo, Wangda; McNeil, Andrew; Wetter, Michael

    2013-05-23

    Building designers are increasingly relying on complex fenestration systems to reduce energy consumed for lighting and HVAC in low energy buildings. Radiance, a lighting simulation program, has been used to conduct daylighting simulations for complex fenestration systems. Depending on the configurations, the simulation can take hours or even days using a personal computer. This paper describes how to accelerate the matrix multiplication portion of a Radiance three-phase daylight simulation by conducting parallel computing on heterogeneous hardware of a personal computer. The algorithm was optimized and the computational part was implemented in parallel using OpenCL. The speed of new approach wasmore » evaluated using various daylighting simulation cases on a multicore central processing unit and a graphics processing unit. Based on the measurements and analysis of the time usage for the Radiance daylighting simulation, further speedups can be achieved by using fast I/O devices and storing the data in a binary format.« less

  19. Release Path Temperatures of Shock-Compressed Tin from Dynamic Reflectance and Radiance Measurements

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    La Lone, B. M.; Stevens, G. D.; Turley, W. D.

    2013-08-01

    Dynamic reflectance and radiance measurements were conducted for tin samples shock compressed to 35 GPa and released to 15 GPa using high explosives. We determined the reflectance of the tin samples glued to lithium fluoride windows using an integrating sphere with an internal xenon flashlamp as an illumination source. The dynamic reflectance (R) was determined at near normal incidence in four spectral bands with coverage in visible and near-infrared spectra. Uncertainties in R/R0 are < 2%, and uncertainties in absolute reflectance are < 5%. In complementary experiments, thermal radiance from the tin/glue/lithium fluoride interface was recorded with similar shock stressmore » and spectral coverage as the reflectance measurements. The two sets of experiments were combined to obtain the temperature history of the tin surface with an uncertainty of < 2%. The stress at the interface was determined from photonic Doppler velocimetry and combined with the temperatures to obtain temperature-stress release paths for tin. We discuss the relationship between the experimental release paths and release isentropes that begin on the principal shock Hugoniot.« less

  20. The effect of spatial and spectral heterogeneity of ground-based light sources on night-sky radiances

    NASA Astrophysics Data System (ADS)

    Kocifaj, M.; Aubé, M.; Kohút, I.

    2010-12-01

    Nowadays, light pollution is a permanent problem at many observatories around the world. Elimination of excessive lighting during the night is not only about reduction of the total luminous power of ground-based light sources, but also involves experimenting with the spectral features of single lamps. Astronomical photometry is typically made at specific wavelengths, and thus the analysis of the spectral effects of light pollution is highly important. Nevertheless, studies on the spectral behaviour of night light are quite rare. Instead, broad-band or integral quantities (such as sky luminance) are preferentially measured and modelled. The knowledge of night-light spectra is necessary for the proper interpretation of narrow-band photometry data. In this paper, the night-sky radiances in the nominal spectral lines of the B (445 nm) and V (551 nm) filters are determined numerically under clear-sky conditions. Simultaneously, the corresponding sky-luminance patterns are computed and compared against the spectral radiances. It is shown that spectra, patterns and distances of the most important light sources (towns) surrounding an observatory are essential for determining the light pollution levels. In addition, the optical characteristics of the local atmosphere can change the angular behaviour of the sky radiance or luminance. All these effects are evaluated for two Slovakian observatories: Stará Lesná and Vartovka.

  1. Characterization of the oceanic light field within the photic zone: Fluctuations of downward irradiance and asymmetry of horizontal radiance

    NASA Astrophysics Data System (ADS)

    Gassmann, Ewa

    Two distinctive features of underwater light field in the upper ocean were examined: the wave-induced high-frequency light fluctuations within the near-surface layer under sunny skies, and the asymmetry of horizontal radiance within the photic layer of the ocean. To characterize the spatiotemporal statistical properties of the wave-induced light fluctuations, measurements of downward plane irradiance were made with novel instrumentation within the top 10 m layer of the ocean at depths as shallow as 10 cm under sunny skies, different solar zenith angles, and weak to moderate wind speeds. It was found that the maximum intensity of light fluctuations occurs at depths as shallow as 20 cm under the most favorable conditions for wave focusing, which correspond to high sun in a clear sky with weak wind. The strong frequency dependence of light fluctuations at shallow near-surface depths indicates dominant frequency range of 1 -- 3 Hz under favorable conditions that shifts toward lower frequencies with increasing depth. The light fluctuations were found to be spatially correlated over horizontal distances varying from few up to 10 -- 20 cm at temporal scales of 0.3 -- 1 sec (at the dominant frequency of 1 -- 3 Hz). The distance of correlation showed a tendency to increase with increasing depth, solar zenith angle, and wind speed. The observed variations in spatiotemporal statistical properties of underwater light fluctuations with depth and environmental conditions are driven largely by weakening of sunlight focusing which is associated with light scattering within the water column, in the atmosphere and at the air-sea interface. To investigate the underwater horizontal radiance field, measurements of horizontal spectral radiance in two opposite directions (solar and anti-solar azimuths) within the solar principal plane were made within the photic layer of the open ocean. The ratio of these two horizontal radiances represents the asymmetry of horizontal radiance field. In

  2. Factors affecting dignity of patients with multiple sclerosis.

    PubMed

    Sharifi, Simin; Borhani, Fariba; Abbaszadeh, Abbas

    2016-12-01

    MS is one of the most common chronic diseases of the nervous system. Apart from disease progression, other complications such as unemployment, separation and divorce could potentially threat patients' dignity. Most of the previous studies have been done of maintaining patients' dignity in interaction with healthcare team, but studies on affecting factors of dignity in chronic patients in the society and in interaction with usual people are scarce. We aimed to investigate factors affecting dignity of Iranian patients with MS in daily living and in interaction of them with the society. In this qualitative study, 13 patients with multiple sclerosis were chosen by purposive sampling and semi-structured interviews were conducted until data saturation. The study was done in Tehran, the capital city of Iran. Factors affecting dignity were classified as 'personal factors' and 'social factors'. Personal factors consist of the following subcategories: patients' communication with self, patients' knowledge, patients' values and beliefs and patients' resources. Social factors include others' communication with patients, social knowledge, social values and beliefs and social resources. Multiple personal and social factors interfere in perceived patient dignity. In fact, interaction between personal and social factors can be influential in final perceived dignity. By focusing on whole aspects of the patients' lives, we can identify dignity-promoting or dignity-threatening factors and help patients maintain their dignity by taking appropriate measures for moderating threatening factors and improving dignity enhancing ones. © 2016 Nordic College of Caring Science.

  3. Development of Multi-Sensor Global Cloud and Radiance Composites for DSCOVR EPIC Imager with Subpixel Definition

    NASA Technical Reports Server (NTRS)

    Khlopenkov, Konstantin V.; Duda, David; Thieman, Mandana; Sun-mack, Szedung; Su, Wenying; Minnis, Patrick; Bedka, Kristopher

    2017-01-01

    The Deep Space Climate Observatory (DSCOVR) enables analysis of the daytime Earth radiation budget via the onboard Earth Polychromatic Imaging Camera (EPIC) and National Institute of Standards and Technology Advanced Radiometer (NISTAR). EPIC delivers adequate spatial resolution imagery but only in shortwave bands (317-780 nm), while NISTAR measures the top-of-atmosphere (TOA) whole-disk radiance in shortwave and longwave broadband windows. Accurate calculation of albedo and outgoing longwave flux requires a high-resolution scene identification such as the radiance observations and cloud properties retrievals from low earth orbit (LEO, including NASA Terra and Aqua MODIS, Suomi-NPP VIIRS, and NOAA AVHRR) and geosynchronous (GEO, including GOES east and west, METEOSAT, INSAT-3D, MTSAT-2, and Himawari-8) satellite imagers. The cloud properties are derived using the Clouds and the Earth's Radiant Energy System (CERES) mission Cloud Subsystem group algorithms. These properties have to be co-located with EPIC pixels to provide the scene identification and to select anisotropic directional models (ADMs), which are then used to adjust the NISTAR-measured radiance and subsequently obtain the global daytime shortwave and longwave fluxes. This work presents an algorithm for optimal merging of selected radiance and cloud property parameters derived from multiple satellite imagers to obtain seamless global hourly composites at 5-km resolution. Selection of satellite data for each 5-km pixel is based on an aggregated rating that incorporates five parameters: nominal satellite resolution, pixel time relative to the EPIC time, viewing zenith angle, distance from day/night terminator, and probability of sun glint. To provide a smoother transition in the merged output, in regions where candidate pixel data from two satellite sources have comparable aggregated rating, the selection decision is defined by the cumulative function of the normal distribution so that abrupt changes in

  4. Infrared Spectral Radiance Intercomparisons With Satellite and Aircraft Sensors

    NASA Technical Reports Server (NTRS)

    Larar, Allen M.; Zhou, Daniel K.; Liu, Xu; Smith, William L.

    2014-01-01

    Measurement system validation is critical for advanced satellite sounders to reach their full potential of improving observations of the Earth's atmosphere, clouds, and surface for enabling enhancements in weather prediction, climate monitoring capability, and environmental change detection. Experimental field campaigns, focusing on satellite under-flights with well-calibrated FTS sensors aboard high-altitude aircraft, are an essential part of the validation task. Airborne FTS systems can enable an independent, SI-traceable measurement system validation by directly measuring the same level-1 parameters spatially and temporally coincident with the satellite sensor of interest. Continuation of aircraft under-flights for multiple satellites during multiple field campaigns enables long-term monitoring of system performance and inter-satellite cross-validation. The NASA / NPOESS Airborne Sounder Testbed - Interferometer (NAST-I) has been a significant contributor in this area by providing coincident high spectral/spatial resolution observations of infrared spectral radiances along with independently-retrieved geophysical products for comparison with like products from satellite sensors being validated. This presentation gives an overview of benefits achieved using airborne sensors such as NAST-I utilizing examples from recent field campaigns. The methodology implemented is not only beneficial to new sensors such as the Cross-track Infrared Sounder (CrIS) flying aboard the Suomi NPP and future JPSS satellites but also of significant benefit to sensors of longer flight heritage such as the Atmospheric InfraRed Sounder (AIRS) and the Infrared Atmospheric Sounding Interferometer (IASI) on the AQUA and METOP-A platforms, respectively, to ensure data quality continuity important for climate and other applications. Infrared spectral radiance inter-comparisons are discussed with a particular focus on usage of NAST-I data for enabling inter-platform cross-validation.

  5. Effect of radiance-to-reflectance transformation and atmosphere removal on maximum likelihood classification accuracy of high-dimensional remote sensing data

    NASA Technical Reports Server (NTRS)

    Hoffbeck, Joseph P.; Landgrebe, David A.

    1994-01-01

    Many analysis algorithms for high-dimensional remote sensing data require that the remotely sensed radiance spectra be transformed to approximate reflectance to allow comparison with a library of laboratory reflectance spectra. In maximum likelihood classification, however, the remotely sensed spectra are compared to training samples, thus a transformation to reflectance may or may not be helpful. The effect of several radiance-to-reflectance transformations on maximum likelihood classification accuracy is investigated in this paper. We show that the empirical line approach, LOWTRAN7, flat-field correction, single spectrum method, and internal average reflectance are all non-singular affine transformations, and that non-singular affine transformations have no effect on discriminant analysis feature extraction and maximum likelihood classification accuracy. (An affine transformation is a linear transformation with an optional offset.) Since the Atmosphere Removal Program (ATREM) and the log residue method are not affine transformations, experiments with Airborne Visible/Infrared Imaging Spectrometer (AVIRIS) data were conducted to determine the effect of these transformations on maximum likelihood classification accuracy. The average classification accuracy of the data transformed by ATREM and the log residue method was slightly less than the accuracy of the original radiance data. Since the radiance-to-reflectance transformations allow direct comparison of remotely sensed spectra with laboratory reflectance spectra, they can be quite useful in labeling the training samples required by maximum likelihood classification, but these transformations have only a slight effect or no effect at all on discriminant analysis and maximum likelihood classification accuracy.

  6. Calculations of Reflected and Transmitted Radiance for Earth's Atmosphere.

    PubMed

    Plass, G N; Kattawar, G W

    1968-06-01

    The reflected and transmitted radiance of the earth's atmosphere is calculated by Monte Carlo techniques. The exact scattering function for the aerosols is used as calculated from the Mie theory. The aerosol vs height distributions proposed by Elterman and by Kondratiev et al. are compared. The Rayleigh and aerosol scattering events are included in the calculation, as well as the ozone absorption, where appropriate. Results are given at wavelengths of 0.27 micro, 0.3 micro, 0.4 micro, 0.7 micro, and 1.67 micro. The mean optical paths of the reflected and transmitted photons, the flux at the lower boundary, and the planetary albedo are tabulated.

  7. EPIC Radiance Simulator for Deep Space Climate ObserVatoRy (DSCOVR)

    NASA Technical Reports Server (NTRS)

    Lyapustin, Alexei; Marshak, Alexander; Wang, Yujie; Korkin, Sergey; Herman, Jay

    2011-01-01

    The Deep Space Climate ObserVatoRy (DSCOVR) is a planned space weather mission for the Sun and Earth observations from the Lagrangian L1 point. Onboard of DSCOVR is a multispectral imager EPIC designed for unique observations of the full illuminated disk of the Earth with high temporal and 10 km spatial resolution. Depending on latitude, EPIC will observe the same Earth surface area during the course of the day in a wide range of solar and view zenith angles in the backscattering view geometry with the scattering angle of 164-172 . To understand the information content of EPIC data for analysis of the Earth clouds, aerosols and surface properties, an EPIC radiance Simulator was developed covering the UV -VIS-NIR range including the oxygen A and B-bands (A=340, 388, 443, 555, 680, 779.5, 687.7, 763.3 nm). The Simulator uses ancillary data (surface pressure/height, NCEP wind speed) as well as MODIS-based geophysical fields such as spectral surface bidirectional reflectance, column water vapor, and properties of aerosols and clouds including optical depth, effective radius, phase and cloud top height. The original simulations are conducted at 1 km resolution using the look-up table approach and then are averaged to 10 km EPIC radiances. This talk will give an overview of the EPIC Simulator with analysis of results over the continental USA and northern Atlantic.

  8. Impact of Assimilation of Conventional and Satellite Radiance GTS Observations on Simulation of Mesoscale Convective System Over Southeast India Using WRF-3DVar

    NASA Astrophysics Data System (ADS)

    Madhulatha, A.; Rajeevan, M.; Bhowmik, S. K. Roy; Das, A. K.

    2018-01-01

    The primary goal of present study is to investigate the impact of assimilation of conventional and satellite radiance observations in simulating the mesoscale convective system (MCS) formed over south east India. An assimilation methodology based on Weather Research and Forecasting model three dimensional variational data assimilation is considered. Few numerical experiments are carried out to examine the individual and combined impact of conventional and non-conventional (satellite radiance) observations. After the successful inclusion of additional observations, strong analysis increments of temperature and moisture fields are noticed and contributed to significant improvement in model's initial fields. The resulting model simulations are able to successfully reproduce the prominent synoptic features responsible for the initiation of MCS. Among all the experiments, the final experiment in which both conventional and satellite radiance observations assimilated has showed considerable impact on the prediction of MCS. The location, genesis, intensity, propagation and development of rain bands associated with the MCS are simulated reasonably well. The biases of simulated temperature, moisture and wind fields at surface and different pressure levels are reduced. Thermodynamic, dynamic and vertical structure of convective cells associated with the passage of MCS are well captured. Spatial distribution of rainfall is fairly reproduced and comparable to TRMM observations. It is demonstrated that incorporation of conventional and satellite radiance observations improved the local and synoptic representation of temperature, moisture fields from surface to different levels of atmosphere. This study highlights the importance of assimilation of conventional and satellite radiances in improving the models initial conditions and simulation of MCS.

  9. A Search for Mountain Waves in MLS Stratospheric Limb Radiances from the Winter Northern Hemisphere: Data Analysis and Global Mountain Wave Modeling

    DTIC Science & Technology

    2004-02-11

    the general circulation of the middle atmosphere, Philos. Trans. R. Soc. London, Ser. A, 323, 693–705. Anton , H. (2000), Elementary Linear Algebra ...Because the saturated radiances may depend slightly on tangent height as the limb path length decreases, a linear trend (described by parameters a and b...track days and interpolated onto the same limb-track orbits. The color bar scale for radiance variance is linear . (b) Digital elevations of northern

  10. CALIPSO IIR Version 2 Level 1b calibrated radiances: analysis and reduction of residual biases in the Northern Hemisphere

    NASA Astrophysics Data System (ADS)

    Garnier, Anne; Trémas, Thierry; Pelon, Jacques; Lee, Kam-Pui; Nobileau, Delphine; Gross-Colzy, Lydwine; Pascal, Nicolas; Ferrage, Pascale; Scott, Noëlle A.

    2018-04-01

    Version 2 of the Level 1b calibrated radiances of the Imaging Infrared Radiometer (IIR) on board the Cloud-Aerosol Lidar and Infrared Satellite Observation (CALIPSO) satellite has been released recently. This new version incorporates corrections of small but systematic seasonal calibration biases previously revealed in Version 1 data products mostly north of 30° N. These biases - of different amplitudes in the three IIR channels 8.65 µm (IIR1), 10.6 µm (IIR2), and 12.05 µm (IIR3) - were made apparent by a striping effect in images of IIR inter-channel brightness temperature differences (BTDs) and through seasonal warm biases of nighttime IIR brightness temperatures in the 30-60° N latitude range. The latter were highlighted through observed and simulated comparisons with similar channels of the Moderate Resolution Imaging Spectroradiometer (MODIS) on board the Aqua spacecraft. To characterize the calibration biases affecting Version 1 data, a semi-empirical approach is developed, which is based on the in-depth analysis of the IIR internal calibration procedure in conjunction with observations such as statistical comparisons with similar MODIS/Aqua channels. Two types of calibration biases are revealed: an equalization bias affecting part of the individual IIR images and a global bias affecting the radiometric level of each image. These biases are observed only when the temperature of the instrument increases, and they are found to be functions of elapsed time since night-to-day transition, regardless of the season. Correction coefficients of Version 1 radiances could thus be defined and implemented in the Version 2 code. As a result, the striping effect seen in Version 1 is significantly attenuated in Version 2. Systematic discrepancies between nighttime and daytime IIR-MODIS BTDs in the 30-60° N latitude range in summer are reduced from 0.2 K in Version 1 to 0.1 K in Version 2 for IIR1-MODIS29. For IIR2-MODIS31 and IIR3-MODIS32, they are reduced from 0.4 K

  11. Adding a solar-radiance function to the Hošek-Wilkie skylight model.

    PubMed

    Hošek, Lukáš; Wilkie, Alexander

    2013-01-01

    One prerequisite for realistic renderings of outdoor scenes is the proper capturing of the sky's appearance. Currently, an explicit simulation of light scattering in the atmosphere isn't computationally feasible, and won't be in the foreseeable future. Captured luminance patterns have proven their usefulness in practice but can't meet all user needs. To fill this capability gap, computer graphics technology has employed analytical models of sky-dome luminance patterns for more than two decades. For technical reasons, such models deal with only the sky dome's appearance, though, and exclude the solar disc. The widely used model proposed by Arcot Preetham and colleagues employed a separately derived analytical formula for adding a solar emitter of suitable radiant intensity. Although this yields reasonable results, the formula is derived in a manner that doesn't exactly match the conditions in their sky-dome model. But the more sophisticated a skylight model is and the more subtly it can represent different conditions, the more the solar radiance should exactly match the skylight's conditions. Toward that end, researchers propose a solar-radiance function that exactly matches a recently published high-quality analytical skylight model.

  12. Final Report: High Spectral Resolution Atmospheric Emitted Radiance Studies with the ARM UAV

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Revercomb, Henry E.

    1999-12-31

    The active participation in the Atmospheric Radiation Measurement (ARM) Unmanned Airborne Vehicle (UAV) science team that was anticipated in the grant proposal was indefinitely delayed after the first year due to a programmatic decision to exclude the high spectral resolution observations from the existing ARM UAV program. However, this report shows that substantial progress toward the science objectives of this grant have made with the help of separate funding from NASA and other agencies. In the four year grant period (including time extensions), a new high spectral resolution instrument has been flown and has successfully demonstrated the ability to obtainmore » measurements of the type needed in the conduct of this grant. In the near term, the third water vapor intensive observing period (WVIOP-3) in October 2000 will provide an opportunity to bring the high spectral resolution observations of upwelling radiance into the ARM program to complement the downwelling radiance observations from the existing ARM AERI instruments. We look forward to a time when the ARM-UAV program is able to extend its scope to include the capability for making these high spectral resolution measurements from a UAV platform.« less

  13. Time-cumulated visible and infrared radiance histograms used as descriptors of surface and cloud variations

    NASA Technical Reports Server (NTRS)

    Seze, Genevieve; Rossow, William B.

    1991-01-01

    The spatial and temporal stability of the distributions of satellite-measured visible and infrared radiances, caused by variations in clouds and surfaces, are investigated using bidimensional and monodimensional histograms and time-composite images. Similar analysis of the histograms of the original and time-composite images provides separation of the contributions of the space and time variations to the total variations. The variability of both the surfaces and clouds is found to be larger at scales much larger than the minimum resolved by satellite imagery. This study shows that the shapes of these histograms are distinctive characteristics of the different climate regimes and that particular attributes of these histograms can be related to several general, though not universal, properties of clouds and surface variations at regional and synoptic scales. There are also significant exceptions to these relationships in particular climate regimes. The characteristics of these radiance histograms provide a stable well defined descriptor of the cloud and surface properties.

  14. Gravity Wave Variances and Propagation Derived from AIRS Radiances

    NASA Technical Reports Server (NTRS)

    Gong, Jie; Wu, Dong L.; Eckermann, S. D.

    2012-01-01

    As the first gravity wave (GW) climatology study using nadir-viewing infrared sounders, 50 Atmospheric Infrared Sounder (AIRS) radiance channels are selected to estimate GW variances at pressure levels between 2-100 hPa. The GW variance for each scan in the cross-track direction is derived from radiance perturbations in the scan, independently of adjacent scans along the orbit. Since the scanning swaths are perpendicular to the satellite orbits, which are inclined meridionally at most latitudes, the zonal component of GW propagation can be inferred by differencing the variances derived between the westmost and the eastmost viewing angles. Consistent with previous GW studies using various satellite instruments, monthly mean AIRS variance shows large enhancements over meridionally oriented mountain ranges as well as some islands at winter hemisphere high latitudes. Enhanced wave activities are also found above tropical deep convective regions. GWs prefer to propagate westward above mountain ranges, and eastward above deep convection. AIRS 90 field-of-views (FOVs), ranging from +48 deg. to -48 deg. off nadir, can detect large-amplitude GWs with a phase velocity propagating preferentially at steep angles (e.g., those from orographic and convective sources). The annual cycle dominates the GW variances and the preferred propagation directions for all latitudes. Indication of a weak two-year variation in the tropics is found, which is presumably related to the Quasi-biennial oscillation (QBO). AIRS geometry makes its out-tracks capable of detecting GWs with vertical wavelengths substantially shorter than the thickness of instrument weighting functions. The novel discovery of AIRS capability of observing shallow inertia GWs will expand the potential of satellite GW remote sensing and provide further constraints on the GW drag parameterization schemes in the general circulation models (GCMs).

  15. New method to calculate back-reflected radiance for isotropic scattering

    NASA Astrophysics Data System (ADS)

    Rinzema, Kees; ten Bosch, Jaap J.; Ferwerda, Hedzer A.; Hoenders, Bernhard J.

    1996-04-01

    We present a method to determine the back reflected radiance from an isotropically scattering halfspace with matched boundary. The bonus of this method lies in the fact that it is capable, in principle, to handle the case of narrow beams, something which, to our knowledge, no other analytic method can do. Essentially, the method derives from a mathematical criterion that effectively forbids the existence of solutions to the transport equation which grown exponentially as one moves away from the surface and deeper into the medium. Preliminary calculations for infinitely wide beams yield results which agree well with what is found in literature.

  16. Potential of remote sensing of cirrus optical thickness by airborne spectral radiance measurements at different sideward viewing angles

    NASA Astrophysics Data System (ADS)

    Wolf, Kevin; Ehrlich, André; Hüneke, Tilman; Pfeilsticker, Klaus; Werner, Frank; Wirth, Martin; Wendisch, Manfred

    2017-03-01

    Spectral radiance measurements collected in nadir and sideward viewing directions by two airborne passive solar remote sensing instruments, the Spectral Modular Airborne Radiation measurement sysTem (SMART) and the Differential Optical Absorption Spectrometer (mini-DOAS), are used to compare the remote sensing results of cirrus optical thickness τ. The comparison is based on a sensitivity study using radiative transfer simulations (RTS) and on data obtained during three airborne field campaigns: the North Atlantic Rainfall VALidation (NARVAL) mission, the Mid-Latitude Cirrus Experiment (ML-CIRRUS) and the Aerosol, Cloud, Precipitation, and Radiation Interactions and Dynamics of Convective Cloud Systems (ACRIDICON) campaign. Radiative transfer simulations are used to quantify the sensitivity of measured upward radiance I with respect to τ, ice crystal effective radius reff, viewing angle of the sensor θV, spectral surface albedo α, and ice crystal shape. From the calculations it is concluded that sideward viewing measurements are generally better suited than radiance data from the nadir direction to retrieve τ of optically thin cirrus, especially at wavelengths larger than λ = 900 nm. Using sideward instead of nadir-directed spectral radiance measurements significantly improves the sensitivity and accuracy in retrieving τ, in particular for optically thin cirrus of τ ≤ 2. The comparison of retrievals of τ based on nadir and sideward viewing radiance measurements from SMART, mini-DOAS and independent estimates of τ from an additional active remote sensing instrument, the Water Vapor Lidar Experiment in Space (WALES), shows general agreement within the range of measurement uncertainties. For the selected example a mean τ of 0.54 ± 0.2 is derived from SMART, and 0.49 ± 0.2 by mini-DOAS nadir channels, while WALES obtained a mean value of τ = 0.32 ± 0.02 at 532 nm wavelength, respectively. The mean of τ derived from the sideward viewing mini

  17. Near-Continuous Profiling of Temperature, Moisture, and Atmospheric Stability Using the Atmospheric Emitted Radiance Interferometer (AERI).

    NASA Astrophysics Data System (ADS)

    Feltz, W. F.; Smith, W. L.; Howell, H. B.; Knuteson, R. O.; Woolf, H.; Revercomb, H. E.

    2003-05-01

    The Department of Energy Atmospheric Radiation Measurement Program (ARM) has funded the development and installation of five ground-based atmospheric emitted radiance interferometer (AERI) systems at the Southern Great Plains (SGP) site. The purpose of this paper is to provide an overview of the AERI instrument, improvement of the AERI temperature and moisture retrieval technique, new profiling utility, and validation of high-temporal-resolution AERI-derived stability indices important for convective nowcasting. AERI systems have been built at the University of Wisconsin-Madison, Madison, Wisconsin, and deployed in the Oklahoma-Kansas area collocated with National Oceanic and Atmospheric Administration 404-MHz wind profilers at Lamont, Vici, Purcell, and Morris, Oklahoma, and Hillsboro, Kansas. The AERI systems produce absolutely calibrated atmospheric infrared emitted radiances at one-wavenumber resolution from 3 to 20 m at less than 10-min temporal resolution. The instruments are robust, are automated in the field, and are monitored via the Internet in near-real time. The infrared radiances measured by the AERI systems contain meteorological information about the vertical structure of temperature and water vapor in the planetary boundary layer (PBL; 0-3 km). A mature temperature and water vapor retrieval algorithm has been developed over a 10-yr period that provides vertical profiles at less than 10-min temporal resolution to 3 km in the PBL. A statistical retrieval is combined with the hourly Geostationary Operational Environmental Satellite (GOES) sounder water vapor or Rapid Update Cycle, version 2, numerical weather prediction (NWP) model profiles to provide a nominal hybrid first guess of temperature and moisture to the AERI physical retrieval algorithm. The hourly satellite or NWP data provide a best estimate of the atmospheric state in the upper PBL; the AERI radiances provide the mesoscale temperature and moisture profile correction in the PBL to the

  18. Bidirectional reflectance correction model for coastal water and its application to minimization of uncertainties in satellite and in-situ water leaving radiances at Long Island Sound Coastal Observatory site

    NASA Astrophysics Data System (ADS)

    Hlaing, Soe Min

    Ocean Color data validation is the absolute requirement to provide the steady and reliable Ocean Color data stream. In the validation of Ocean Color data, water-leaving radiances, retrieved from in situ or satellite measurements, need to be compared in very accurate manner. Both in-situ and satellite data to be used in the comparisons are required to be the representative of the typical water and environmental condition at the site without being affected by the unexpected natural and environmental perturbation. As the result, assessments of the uncertainties in the water leaving radiance data must be carried out in the measurement and the every step of data processing procedure. With the hyper- and multi-spectral water leaving radiance data retrieved for the different viewing geometries of the instruments at the Long Island Sound Coastal Observatory (LISCO), uncertainties in the water leaving radiance data and processing procedures have been assessed and quantified. Recommendations and algorithm improvements have been also made to reduce the uncertainties in the processing and validation of Ocean Color data. Particularly, remote sensing reflectance model to correct the bidirectional angular dependencies in both in-situ and satellite data have been proposed. The proposed model is first validated with a one year time series of in situ above-water measurements acquired by collocated multi- and hyper-spectral radiometers which have different viewing geometries installed at LISCO. Match-ups and inter-comparisons performed on these concurrent measurements show that the proposed algorithm outperforms the algorithm currently in use at all wavelengths, with spectral average improvement of 2.4%. LISCO's time series data has also been used to evaluate improvements in the match-up comparisons of MODIS satellite data when the proposed Bidirectional Reflectance Distribution Function (BRDF) correction is used in lieu of the current algorithm. It has been shown that the

  19. Modeling Seasonal Thermal Radiance Cycles for Change Detection at Volcanic / Geothermal Areas

    NASA Astrophysics Data System (ADS)

    Vaughan, R.; Beuttel, B. S.

    2013-12-01

    Remote sensing observations of thermal features associated with (and often preceding) volcanic activity have been used for decades to detect and monitor volcanism. However, anomalous thermal precursors to volcanic eruptions are usually only recognized retrospectively. One of the reasons for this is that precursor thermal activity is often too subtle in magnitude (spatially, temporally, or in absolute temperature) to be unambiguously detected in time to issue warnings or forecasts. Part of the reason for this is the trade-off between high spatial and high temporal resolution associated with satellite imaging systems. Thus, the goal of this work has been to develop some techniques for using high-temporal-resolution, coarse-spatial-resolution imagery to try to detect subtle thermal anomalies. To identify anomalies, background thermal activity must first be characterized. Every active, or potentially active, volcano has a unique thermal history that provides information about normal background thermal activity due to seasonal or diurnal variations. Understanding these normal variations allows recognition of anomalous activity that may be due to volcanic / hydrothermal processes - ultimately with a lead time that may be sufficient to issue eruption warnings or forecasts. Archived MODIS data, acquired ~daily from 2000 to 2012, were used to investigate seasonal thermal cycles at three volcanic areas with different types of thermal features: Mount St. Helens, which had a dacite dome-building eruption from 2004-2008; Mount Ruapehu, which has a 500-m diameter active summit crater lake; and Yellowstone, which is a large active geothermal system that has hundreds of hot springs and fumarole fields spread out over a very large area. The focus has been on using MODIS 1-km sensor radiance data in the MIR and TIR wavelength regions that are sensitive to thermal emission from features that range in temperature from hundreds of °C, down to tens of °C (below the boiling temperature

  20. Economic and Cultural Factors Affecting University Excellence

    ERIC Educational Resources Information Center

    Jabnoun, Naceur

    2009-01-01

    Purpose: The ranking of top universities in the world has generated increased interest in the factors that enhance university performance. The purpose of this paper is to identify economic and cultural factors that affect the number of top ranking universities in each country. Design/methodology/approach: This paper first identifies the number of…

  1. Imaging Gravity Waves in Lower Stratospheric AMSU-A Radiances. Part 1: Simple Forward Model

    DTIC Science & Technology

    2006-08-14

    brightening” of microwave radiances acquired from purely vertical background temperature profiles by cross- track scanners. Waves propagating along track...three-dimensional wave fields. For example, some limb sensors return high- resolution vertical temperature profiles with wave oscilla- tions...provide only ver- tical profiles of wave oscillations, similar to radiosonde and rocketsonde data. Similarly, limb-tracking measurements from the

  2. Goddard Laser for Absolute Measurement of Radiance for Instrument Calibration in the Ultraviolet to Short Wave Infrared

    NASA Technical Reports Server (NTRS)

    McAndrew, Brendan; McCorkel, Joel; Shuman, Timothy; Zukowski, Barbara; Traore, Aboubakar; Rodriguez, Michael; Brown, Steven; Woodward, John

    2018-01-01

    A description of the Goddard Laser for Absolute Calibration of Radiance, a tunable, narrow linewidth spectroradiometric calibration tool, and results from calibration of an earth science satellite instrument from ultraviolet to short wave infrared wavelengths.

  3. ENVIRONMENTAL FACTORS AFFECTING BREAST CANCER SUSCEPTIBILITY

    EPA Science Inventory

    Environmental Factors Affecting Breast Cancer Susceptibility
    Suzanne. E. Fenton
    US EPA, ORD, MD-67 NHEERL, Reproductive Toxicology Division, Research Triangle Park, NC 27711.

    Breast cancer is still the most common malignancy afflicting women in the Western world. Alt...

  4. Factors Affecting Radon Concentration in Houses

    NASA Astrophysics Data System (ADS)

    Al-Sharif, Abdel-Latif; Abdelrahman, Y. S.

    2001-03-01

    The dangers to the human health upon exposure to radon and its daughter products is the main motivation behind the vast number of studies performed to find the concentration of radon in our living environment, including our houses. The presence of radon and its daughter products in houses are due to various sources including building materials and the soil under the houses. Many factors affect radon concentration in our houses, the elevation above ground level,ventilation, building materials and room usage being among these factors. In our paper, we discuss the effect of elevation above ground level, room usage and ventilation on the Radon concentration in houses. The faculty residences of the Mu'tah University (Jordan) were chosen in our study. Our results showed that the concentration of radon decreases with elevation. Ventilation rate was also found to affect radon concentration, where low concentrations observed for areas with good ventilation.

  5. Sun and Sky Radiance Measurements and Data Analysis Protocols. Chapter 5

    NASA Technical Reports Server (NTRS)

    Frouin, Robert; Holben, Brent; Miller, Mark; Pietras, Christophe; Porter, John; Voss, Ken

    2001-01-01

    This chapter is concerned with two types of radiometric measurements essential to verify atmospheric correction algorithms and to calibrate vicariously satellite ocean color sensors. The first type is a photometric measurement of the direct solar beam to determine the optical thickness of the atmosphere. The intensity of the solar beam can be measured directly, or obtained indirectly from measurements of diffuse global upper hemispheric irradiance. The second type is a measurement of the solar aureole and sky radiance distribution using a CCD camera, or a scanning radiometer viewing in and perpendicular to the solar principal plane. From the two types of measurements, the optical properties of aerosols, highly variable in space and time, can be derived. Because of the high variability, the aerosol properties should be known at the time of satellite overpass. Atmospheric optics measurements, however, are not easy to perform at sea, from a ship or any platform. This complicates the measurement protocols and data analysis. Some instrumentation cannot be deployed at sea, and is limited to island and coastal sites. In the following, measurement protocols are described for radiometers commonly used to measure direct atmospheric transmittance and sky radiance, namely standard sun photometers, fast-rotating shadow-band radiometers, automated sky scanning systems, and CCD cameras. Methods and procedures to analyze and quality control the data are discussed, as well as proper measurement strategies for evaluation of atmospheric correction algorithms and satellite-derived ocean color.

  6. Introducing Multisensor Satellite Radiance-Based Evaluation for Regional Earth System Modeling

    NASA Technical Reports Server (NTRS)

    Matsui, T.; Santanello, J.; Shi, J. J.; Tao, W.-K.; Wu, D.; Peters-Lidard, C.; Kemp, E.; Chin, M.; Starr, D.; Sekiguchi, M.; hide

    2014-01-01

    Earth System modeling has become more complex, and its evaluation using satellite data has also become more difficult due to model and data diversity. Therefore, the fundamental methodology of using satellite direct measurements with instrumental simulators should be addressed especially for modeling community members lacking a solid background of radiative transfer and scattering theory. This manuscript introduces principles of multisatellite, multisensor radiance-based evaluation methods for a fully coupled regional Earth System model: NASA-Unified Weather Research and Forecasting (NU-WRF) model. We use a NU-WRF case study simulation over West Africa as an example of evaluating aerosol-cloud-precipitation-land processes with various satellite observations. NU-WRF-simulated geophysical parameters are converted to the satellite-observable raw radiance and backscatter under nearly consistent physics assumptions via the multisensor satellite simulator, the Goddard Satellite Data Simulator Unit. We present varied examples of simple yet robust methods that characterize forecast errors and model physics biases through the spatial and statistical interpretation of various satellite raw signals: infrared brightness temperature (Tb) for surface skin temperature and cloud top temperature, microwave Tb for precipitation ice and surface flooding, and radar and lidar backscatter for aerosol-cloud profiling simultaneously. Because raw satellite signals integrate many sources of geophysical information, we demonstrate user-defined thresholds and a simple statistical process to facilitate evaluations, including the infrared-microwave-based cloud types and lidar/radar-based profile classifications.

  7. Experimental evaluation of theoretical sea surface reflectance factors relevant to above-water radiometry.

    PubMed

    Zibordi, Giuseppe

    2016-03-21

    Determination of the water-leaving radiance LW through above-water radiometry requires knowledge of accurate reflectance factors ρ of the sea surface. Publicly available ρ relevant to above-water radiometry include theoretical data sets generated: i. by assuming a sky radiance distribution accounting for aerosols and multiple scattering, but neglecting polarization, and quantifying sea surface effects through Cox-Munk wave slope statistics; or differently ii. accounting for polarization, but assuming an ideal Rayleigh sky radiance distribution, and quantifying sea surface effects through modeled wave elevation and slope variance spectra. The impact on above-water data products of differences between those factors ρ was quantified through comparison of LW from the Ocean Color component of the Aerosol Robotic Network (AERONET-OC) with collocated LW from in-water radiometry. Results from the analysis of radiance measurements from the sea performed with 40 degrees viewing angle and 90 degrees azimuth offset with respect to the sun plane, indicated a slightly better agreement between above- and in-water LW determined for wind speeds tentatively lower than 4 m s-1 with ρ computed accounting for aerosols, multiple scattering and Cox-Munk surfaces. Nevertheless, analyses performed by partitioning the investigated data set also indicated that actual ρ values would exhibit dependence on sun zenith comprised between those characterizing the two sets of reflectance factors.

  8. Factors affecting caregivers' ability to make environmental modifications.

    PubMed

    Messecar, D C

    2000-12-01

    This study explored factors that family caregivers described as affecting their ability to use environmental modifications. Intensive interviews and participant observation were used to collect detailed data from 24 primary family caregivers. Several factors that affect the caregivers' ability to implement modification strategies were identified in the analysis. These factors included attributes of the elderly individual, attributes of the modification, quality of the caregiver-elderly relationship, caregivers' skills, personal resources of the caregiver, and the informal and formal supports available. Of these factors, the most important were the salient skills that caregivers need to implement environmental modifications. These findings point to the importance of caregivers receiving skills training in this important dimension of caregiving. Intervention should be based on a collaborative approach that ensures the caregiver and care receiver's needs and preferences are respected.

  9. Which factors affect software projects maintenance cost more?

    PubMed

    Dehaghani, Sayed Mehdi Hejazi; Hajrahimi, Nafiseh

    2013-03-01

    The software industry has had significant progress in recent years. The entire life of software includes two phases: production and maintenance. Software maintenance cost is increasingly growing and estimates showed that about 90% of software life cost is related to its maintenance phase. Extraction and considering the factors affecting the software maintenance cost help to estimate the cost and reduce it by controlling the factors. In this study, the factors affecting software maintenance cost were determined then were ranked based on their priority and after that effective ways to reduce the maintenance costs were presented. This paper is a research study. 15 software related to health care centers information systems in Isfahan University of Medical Sciences and hospitals function were studied in the years 2010 to 2011. Among Medical software maintenance team members, 40 were selected as sample. After interviews with experts in this field, factors affecting maintenance cost were determined. In order to prioritize the factors derived by AHP, at first, measurement criteria (factors found) were appointed by members of the maintenance team and eventually were prioritized with the help of EC software. Based on the results of this study, 32 factors were obtained which were classified in six groups. "Project" was ranked the most effective feature in maintenance cost with the highest priority. By taking into account some major elements like careful feasibility of IT projects, full documentation and accompany the designers in the maintenance phase good results can be achieved to reduce maintenance costs and increase longevity of the software.

  10. One year of downwelling spectral radiance measurements from 100 to 1400 cm-1 at Dome Concordia: Results in clear conditions

    NASA Astrophysics Data System (ADS)

    Rizzi, R.; Arosio, C.; Maestri, T.; Palchetti, L.; Bianchini, G.; Del Guasta, M.

    2016-09-01

    The present work examines downwelling radiance spectra measured at the ground during 2013 by a Far Infrared Fourier Transform Spectrometer at Dome C, Antarctica. A tropospheric backscatter and depolarization lidar is also deployed at same site, and a radiosonde system is routinely operative. The measurements allow characterization of the water vapor and clouds infrared properties in Antarctica under all sky conditions. In this paper we specifically discuss cloud detection and the analysis in clear sky condition, required for the discussion of the results obtained in cloudy conditions. First, the paper discusses the procedures adopted for the quality control of spectra acquired automatically. Then it describes the classification procedure used to discriminate spectra measured in clear sky from cloudy conditions. Finally a selection is performed and 66 clear cases, spanning the whole year, are compared to simulations. The computation of layer molecular optical depth is performed with line-by-line techniques and a convolution to simulate the Radiation Explorer in the Far InfraRed-Prototype for Applications and Development (REFIR-PAD) measurements; the downwelling radiance for selected clear cases is computed with a state-of-the-art adding-doubling code. The mean difference over all selected cases between simulated and measured radiance is within experimental error for all the selected microwindows except for the negative residuals found for all microwindows in the range 200 to 400 cm-1, with largest values around 295.1 cm-1. The paper discusses possible reasons for the discrepancy and identifies the incorrect magnitude of the water vapor total absorption coefficient as the cause of such large negative radiance bias below 400 cm-1.

  11. The Use of Transfer Radiometers in Validating the Visible through Shortwave Infrared Calibrations of Radiance Sources Used by Instruments in NASA's Earth Observing System

    NASA Technical Reports Server (NTRS)

    Butler, James J.; Barnes, Robert A.

    2002-01-01

    The detection and study of climate change over a time frame of decades requires successive generations of satellite, airborne, and ground-based instrumentation carefully calibrated against a common radiance scale. In NASA s Earth Observing System (EOS) program, the pre-launch radiometric calibration of these instruments in the wavelength region from 400 nm to 2500 nm is accomplished using internally illuminated integrating spheres and diffuse reflectance panels illuminated by irradiance standard lamps. Since 1995, the EOS Calibration Program operating within the EOS Project Science Office (PSO) has enlisted the expertise of national standards laboratories and government and university metrology laboratories in an effort to validate the radiance scales assigned to sphere and panel radiance sources by EOS instrument calibration facilities. This state-of-the-art program has been accomplished using ultra-stable transfer radiometers independently calibrated by the above participating institutions. In ten comparisons since February 1995, the agreement between the radiance measurements of the transfer radiometers is plus or minus 1.80% at 411 nm, plus or minus 1.31% at 552.5 nm, plus or minus 1.32% at 868.0 nm, plus or minus 2.54% at 1622nm, and plus or minus 2.81% at 2200nm (sigma =1).

  12. Preslaughter factors affecting poultry meat quality chapter 2.

    USDA-ARS?s Scientific Manuscript database

    Poultry meat quality is affected by numerous antemortem factors, in particular those occurring during the last 24 hours that the bird is alive. These short term factors influence carcass yield (live shrink), carcass defects (bruising, broken/dislocated bones), carcass microbiological contamination, ...

  13. A comparison of measured and calculated upwelling radiance over water as a function of sensor altitude

    NASA Technical Reports Server (NTRS)

    Coney, T. A.; Salzman, J. A.

    1979-01-01

    A comparison is made between remote sensing data measured over water at altitudes ranging from 30 m to 15.2 km and data calculated for corresponding altitudes using surface measurements and an atmospheric radiative transfer model. Data were acquired on June 22, 1978 in Lake Erie, a cloudless, calm, near haze free day. Suspended solids and chlorophyll concentrations were 0.59 + or - 0.02 mg/1 and 2.42 + or - 0.03 micrograms/1 respectively throughout the duration of the experiment. Remote sensor data were acquired by two multispectral scanners each having 10 bands between 410 nm and 1040 nm. Calculated and measured nadir radiances for altitudes of 152 m and 12.5 km agree to within 16% and 14% respectively. The variation in measured radiance with look angle was poorly simulated by the model. It was concluded that an accurate assessment of the source of error will require the inclusion in the analysis of the contributions made by the sea state and specular sky reflectance.

  14. A comparison of measured and calculated upwelling radiance over water as a function of sensor altitude

    NASA Technical Reports Server (NTRS)

    Coney, T. A.; Salzman, J. A.

    1979-01-01

    The present paper compares remote sensing data measured over water at altitudes ranging from 30 m to 15.2 km to data calculated for corresponding altitudes using surface measurements and an atmospheric radiative transfer model. The data were acquired on June 22, 1978 in Lake Erie and it was found that suspended solids and chlorophyll concentrations were 0.59 + or - 0.02 mg/liter and 2.42 + or - 0.03 micro gram/liter respectively throughout the duration of the experiment. Calculated and measured nadir radiances for altitudes of 152 m and 12.5 km agree to within 16% and 14% respectively. It is noted that the model offered a poor simulation of the variation in measured radiance with look angle. Finally, it is concluded that an accurate assessment of the source of error will require the inclusion in the analysis of the contributions made by the sea state and specular sky reflectance

  15. Comparison of full-sky polarization and radiance observations to radiative transfer simulations which employ AERONET products.

    PubMed

    Pust, Nathan J; Dahlberg, Andrew R; Thomas, Michael J; Shaw, Joseph A

    2011-09-12

    Visible-band and near infrared polarization and radiance images measured with a ground-based full-sky polarimeter are compared against a successive orders of scattering (SOS) radiative transfer model for 2009 summer cloud-free days in Bozeman, Montana, USA. The polarimeter measures radiance and polarization in 10-nm bands centered at 450 nm, 490 nm, 530 nm, 630 nm, and 700 nm. AERONET products are used to represent aerosols in the SOS model, while MISR satellite BRF products are used for the surface reflectance. While model results generally agree well with observation, the simulated degree of polarization is typically higher than observed data. Potential sources of this difference may include cloud contamination and/or underestimation of the AERONET-retrieved aerosol real refractive index. Problems with the retrieved parameters are not unexpected given the low aerosol optical depth range (0.025 to 0.17 at 500 nm) during the study and the corresponding difficulties that these conditions pose to the AERONET inversion algorithm.

  16. A methodology for obtaining on-orbit SI-traceable spectral radiance measurements in the thermal infrared

    NASA Astrophysics Data System (ADS)

    Dykema, John A.; Anderson, James G.

    2006-06-01

    A methodology to achieve spectral thermal radiance measurements from space with demonstrable on-orbit traceability to the International System of Units (SI) is described. This technique results in measurements of infrared spectral radiance R(\\tilde {\\upsilon }) , with spectral index \\tilde {\\upsilon } in cm-1, with a relative combined uncertainty u_c[R(\\tilde {\\upsilon })] of 0.0015 (k = 1) for the average mid-infrared radiance emitted by the Earth. This combined uncertainty, expressed in brightness temperature units, is equivalent to ±0.1 K at 250 K at 750 cm-1. This measurement goal is achieved by utilizing a new method for infrared scale realization combined with an instrument design optimized to minimize component uncertainties and admit tests of radiometric performance. The SI traceability of the instrument scale is established by evaluation against source-based and detector-based infrared scales in defined laboratory protocols before launch. A novel strategy is executed to ensure fidelity of on-orbit calibration to the pre-launch scale. This strategy for on-orbit validation relies on the overdetermination of instrument calibration. The pre-launch calibration against scales derived from physically independent paths to the base SI units provides the foundation for a critical analysis of the overdetermined on-orbit calibration to establish an SI-traceable estimate of the combined measurement uncertainty. Redundant calibration sources and built-in diagnostic tests to assess component measurement uncertainties verify the SI traceability of the instrument calibration over the mission lifetime. This measurement strategy can be realized by a practical instrument, a prototype Fourier-transform spectrometer under development for deployment on a small satellite. The measurement record resulting from the methodology described here meets the observational requirements for climate monitoring and climate model testing and improvement.

  17. FACTORS ADVERSELY AFFECTING AMPHIBIAN POPULATIONS IN THE US

    EPA Science Inventory

    Factors known or suspected to be adversely affecting native amphibian populations in the US were identified using information from species accounts written in a standardized format by multiple authors in a forthcoming book. Specific adverse factors were identified for 53 (58%) of...

  18. Factors affecting radiographers' organizational commitment.

    PubMed

    Akroyd, Duane; Jackowski, Melissa B; Legg, Jeffrey S

    2007-01-01

    A variety of factors influence employees' attitudes toward their workplace and commitment to the organization that employs them. However, these factors have not been well documented among radiologic technologists. To determine the predictive ability of selected organizational, leadership, work-role and demographic variables on organizational commitment for a national sample of radiographers. Three thousand radiographers registered by the American Registry of Radiologic Technologists working full time in clinical settings were surveyed by mail regarding their commitment to their employers, leadership within the organization that employs them, employer support and demographic information. Overall, radiographers were found to have only a moderate level of commitment to their employers. Among the factors that significantly affected commitment were the radiographer's educational level, perceived level of organizational support, role clarity and organizational leadership. The results of this study could provide managers and supervisors with insights on how to empower and challenge radiographers and offer opportunities that will enhance radiographers' commitment to the organization, thus reducing costly turnover and improving employee performance.

  19. Factors Affecting Faculty Web Portal Usability

    ERIC Educational Resources Information Center

    Bringula, Rex P.; Basa, Roselle S.

    2011-01-01

    The study investigated the factors that might significantly affect web portal usability. Results of the study were intended to serve as inputs for faculty web portal development of the University of the East-Manila. Descriptive statistics utilized questionnaire data from 82 faculty members. The data showed that most of the respondents were…

  20. Low Calorie Diet Affects Aging-Related Factors

    MedlinePlus

    ... Research News From NIH Low Calorie Diet Affects Aging-Related Factors Past Issues / Summer 2006 Table of ... project sponsored by the NIH's National Institute on Aging (NIA) to learn more about the effects of ...

  1. What Factors Affect Response to Ads? A Perspective.

    ERIC Educational Resources Information Center

    Rotzoll, Kim B.

    The concept of "frame of reference" offers a perspective from which to examine the many factors which affect advertising response. The advertiser is interested in affecting two types of overt behavior. First, the individual is induced to select a particular stimulus (the advertisement) from competing stimuli (such as other people, noise,…

  2. Snow Radiance Data Assimilation over High Mountain Asia Using the NASA Land Information System and a Well-Trained Support Vector Machine

    NASA Astrophysics Data System (ADS)

    Kwon, Y.; Forman, B. A.; Yoon, Y.; Kumar, S.

    2017-12-01

    High Mountain Asia (HMA) has been progressively losing ice and snow in recent decades, which could negatively impact regional water supply and native ecosystems. One goal of this study is to characterize the spatiotemporal variability of snow (and ice) across the HMA region. In addition, modeled snow water equivalent (SWE) estimates will be enhanced through the assimilation of passive microwave brightness temperatures (TB) collected by the Advanced Microwave Scanning Radiometer for Earth Observing System (AMSR-E) as part of a radiance assimilation system. The radiance assimilation framework includes the NASA Land Information System (LIS) in conjunction with a well-trained support vector machine (SVM) that acts as the observation operator. The Noah Land Surface Model with multi-parameterization options (Noah-MP) is used as the prior model for simulating snow dynamics. Noah-MP is forced by meteorological fields from the NASA Modern-Era Retrospective analysis for Research and Applications, version 2 (MERRA-2) atmospheric reanalysis for the periods 01 Sep. 2002 to 01 Sep. 2011. The radiance assimilation system requires two separate phases: 1) training and 2) assimilation. During the training phase, a nonlinear SVM is generated for three different AMSR-E frequencies - 10.65, 18.7, and 36.5 GHz - at both vertical and horizontal polarization. The trained SVM is then used to predict TB during the assimilation phase. An ensemble Kalman filter will be used to condition the model on AMSR-E brightness temperatures not used during SVM training. The performance of the Noah-MP (with and without radiance assimilation) will be assessed via comparison to in-situ measurements, remotely-sensing geophysical retrievals, and other reanalysis products.

  3. Remote measurement of water color in coastal waters. [spectral radiance data used to obtain quantitative values for chlorophyll and turbidity

    NASA Technical Reports Server (NTRS)

    Weldon, J. W.

    1973-01-01

    An investigation was conducted to develop procedure to obtain quantitative values for chlorophyll and turbidity in coastal waters by observing the changes in spectral radiance of the backscattered spectrum. The technique under consideration consists of Examining Exotech model 20-D spectral radiometer data and determining which radiance ratios best correlated with chlorophyll and turbidity measurements as obtained from analyses of water samples and sechi visibility readings. Preliminary results indicate that there is a correlation between backscattered light and chlorophyll concentration and secchi visibility. The tests were conducted with the spectrometer mounted in a light aircraft over the Mississippi Sound at altitudes of 2.5K, 2.8K and 10K feet.

  4. Affective and Social Factors in a Project-Based Writing Course

    ERIC Educational Resources Information Center

    Kathpalia, Sujata Surinder; Heah, Carmel

    2011-01-01

    Much of the work in academic writing has focused on the cognitive rather than the affective and social aspects involved in project-based writing. Emphasis in past research has been on skills and processes of writing rather than on affective factors such as motivation, attitudes, feelings or social factors involving intrapersonal and interpersonal…

  5. Substrate-Related Factors Affecting Enzymatic Saccharification of Lignocelluloses: Our Recent Understanding

    Treesearch

    Shao-Yuan Leu; J.Y. Zhu

    2013-01-01

    Enzymatic saccharification of cellulose is a key step in conversion of plant biomass to advanced biofuel and chemicals. Many substrate-related factors affect saccharification. Rather than examining the role of each individual factor on overall saccharification efficiency, this study examined how each factor affects the three basic processes of a heterogeneous...

  6. Estimating Top-of-Atmosphere Thermal Infrared Radiance Using MERRA-2 Atmospheric Data

    NASA Astrophysics Data System (ADS)

    Kleynhans, Tania

    Space borne thermal infrared sensors have been extensively used for environmental research as well as cross-calibration of other thermal sensing systems. Thermal infrared data from satellites such as Landsat and Terra/MODIS have limited temporal resolution (with a repeat cycle of 1 to 2 days for Terra/MODIS, and 16 days for Landsat). Thermal instruments with finer temporal resolution on geostationary satellites have limited utility for cross-calibration due to their large view angles. Reanalysis atmospheric data is available on a global spatial grid at three hour intervals making it a potential alternative to existing satellite image data. This research explores using the Modern-Era Retrospective analysis for Research and Applications, Version 2 (MERRA-2) reanalysis data product to predict top-of-atmosphere (TOA) thermal infrared radiance globally at time scales finer than available satellite data. The MERRA-2 data product provides global atmospheric data every three hours from 1980 to the present. Due to the high temporal resolution of the MERRA-2 data product, opportunities for novel research and applications are presented. While MERRA-2 has been used in renewable energy and hydrological studies, this work seeks to leverage the model to predict TOA thermal radiance. Two approaches have been followed, namely physics-based approach and a supervised learning approach, using Terra/MODIS band 31 thermal infrared data as reference. The first physics-based model uses forward modeling to predict TOA thermal radiance. The second model infers the presence of clouds from the MERRA-2 atmospheric data, before applying an atmospheric radiative transfer model. The last physics-based model parameterized the previous model to minimize computation time. The second approach applied four different supervised learning algorithms to the atmospheric data. The algorithms included a linear least squares regression model, a non-linear support vector regression (SVR) model, a multi

  7. Climate Absolute Radiance and Refractivity Observatory (CLARREO)

    NASA Technical Reports Server (NTRS)

    Leckey, John P.

    2015-01-01

    The Climate Absolute Radiance and Refractivity Observatory (CLARREO) is a mission, led and developed by NASA, that will measure a variety of climate variables with an unprecedented accuracy to quantify and attribute climate change. CLARREO consists of three separate instruments: an infrared (IR) spectrometer, a reflected solar (RS) spectrometer, and a radio occultation (RO) instrument. The mission will contain orbiting radiometers with sufficient accuracy, including on orbit verification, to calibrate other space-based instrumentation, increasing their respective accuracy by as much as an order of magnitude. The IR spectrometer is a Fourier Transform spectrometer (FTS) working in the 5 to 50 microns wavelength region with a goal of 0.1 K (k = 3) accuracy. The FTS will achieve this accuracy using phase change cells to verify thermistor accuracy and heated halos to verify blackbody emissivity, both on orbit. The RS spectrometer will measure the reflectance of the atmosphere in the 0.32 to 2.3 microns wavelength region with an accuracy of 0.3% (k = 2). The status of the instrumentation packages and potential mission options will be presented.

  8. Microbiologic factors affecting Clostridium difficile recurrence.

    PubMed

    Chilton, C H; Pickering, D S; Freeman, J

    2018-05-01

    Recurrent Clostridium difficile infection (rCDI) places a huge economic and practical burden on healthcare facilities. Furthermore, rCDI may affect quality of life, leaving patients in an rCDI cycle and dependant on antibiotic therapy. To discuss the importance of microbiologic factors in the development of rCDI. Literature was drawn from a search of PubMed from 2000 onwards with the search term 'recurrent Clostridium difficile infection' and further references cited within these articles. Meta-analyses and systematic reviews have shown that CDI and rCDI risk factors are similar. Development of rCDI is attendant on many factors, including immune status or function, comorbidities and concomitant treatments. Studies suggest that poor bacterial diversity is correlated with clinical rCDI. Narrow-spectrum gut microflora-sparing antimicrobials (e.g. surotomycin, cadazolid, ridinilazole) are in development for CDI treatment, while microbiota therapeutics (faecal microbiota transplantation, nontoxigenic C. difficile, stool substitutes) are increasingly being explored. rCDI can only occur when viable C. difficile spores are present, either within the gut lumen after infection or when reacquired from the environment. C. difficile spore germination can be influenced by gut environmental factors resulting from dysbiosis, and spore outgrowth may be affected stage by some antimicrobials (e.g. fidaxomicin, ramoplanin, oritavancin). rCDI is a significant challenge for healthcare professionals, requiring a multifaceted approach; optimized infection control to minimize reinfection; C. difficile-targeted antibiotics to minimize dysbiosis; and gut microflora restoration to promote colonization resistance. These elements should be informed by our understanding of the microbiologic factors involved in both C. difficile itself and the gut microbiome. Copyright © 2017 European Society of Clinical Microbiology and Infectious Diseases. Published by Elsevier Ltd. All rights reserved.

  9. A comparative study of infrared radiance measurements by an ER-2 based radiometer and the LANDSAT 5 Thematic Mapper (TM-6)

    NASA Technical Reports Server (NTRS)

    Hammer, Philip D.; Valero, Francisco P. J.; Kinne, Stefan

    1990-01-01

    Infrared radiance measurements were acquired from a radiometer on the NASA ER-2 during a coincident LANDSAT 5 overpass on 28 Oct. 1986 as part of the FIRE Cirrus IFO in the vicinity of Lake Michigan. A comparative study is made to infer microphysical properties of the cirrus cloud field. Radiances are derived from the image by convolving the ER-2 radiometer's effective field of view along the flight path. A multistream radiative transfer model is used to account for the differences in spectral bandwidths, 10.40 to 12.50 microns for the LANDSAT band and 9.90 to 10.87 microns for the radiometer.

  10. Factors affecting strategic plan implementation using interpretive structural modeling (ISM).

    PubMed

    Bahadori, Mohammadkarim; Teymourzadeh, Ehsan; Tajik, Hamidreza; Ravangard, Ramin; Raadabadi, Mehdi; Hosseini, Seyed Mojtaba

    2018-06-11

    Purpose Strategic planning is the best tool for managers seeking an informed presence and participation in the market without surrendering to changes. Strategic planning enables managers to achieve their organizational goals and objectives. Hospital goals, such as improving service quality and increasing patient satisfaction cannot be achieved if agreed strategies are not implemented. The purpose of this paper is to investigate the factors affecting strategic plan implementation in one teaching hospital using interpretive structural modeling (ISM). Design/methodology/approach The authors used a descriptive study involving experts and senior managers; 16 were selected as the study sample using a purposive sampling method. Data were collected using a questionnaire designed and prepared based on previous studies. Data were analyzed using ISM. Findings Five main factors affected strategic plan implementation. Although all five variables and factors are top level, "senior manager awareness and participation in the strategic planning process" and "creating and maintaining team participation in the strategic planning process" had maximum drive power. "Organizational structure effects on the strategic planning process" and "Organizational culture effects on the strategic planning process" had maximum dependence power. Practical implications Identifying factors affecting strategic plan implementation is a basis for healthcare quality improvement by analyzing the relationship among factors and overcoming the barriers. Originality/value The authors used ISM to analyze the relationship between factors affecting strategic plan implementation.

  11. Exploring paraprofessional and classroom factors affecting teacher supervision.

    PubMed

    Irvin, Dwight W; Ingram, Paul; Huffman, Jonathan; Mason, Rose; Wills, Howard

    2018-02-01

    Paraprofessionals serve a primary role in supporting students with disabilities in the classroom, which necessitates teachers' supervision as a means to improve their practice. Yet, little is known regarding what factors affect teacher supervision. We sought to identify how paraprofessional competence and classroom type affected the levels of teacher direction. We administered an adapted version of the Paraprofessional Needs, Knowledge & Tasks Survey and the Survey for Teachers Supervising Paraprofessionals to teachers supervising paraprofessionals in elementary schools. Structural Equation Modeling was used to examine the link between paraprofessional competence and classroom factors affecting the level of teacher supervision. Our results indicated that when teachers perceived paraprofessionals as being more skilled, they provided more supervision, and when more supervision was provided the less they thought paraprofessionals should be doing their assigned tasks. Additionally, paraprofessionals working in classrooms with more students with mild disabilities received less supervision than paraprofessionals working in classrooms with more students with moderate-to-severe disabilities. Those paraprofessionals in classrooms serving mostly children with mild disabilities were also perceived as having lower levels of skill competence than those serving in classrooms with students with more moderate-to-severe disabilities. By understanding the factors that affect teacher supervision, policy and professional development opportunities can be refined/developed to better support both supervising teachers and paraprofessionals and, in turn, improve the outcomes of children with disabilities. Copyright © 2017 Elsevier Ltd. All rights reserved.

  12. Ranking factors affecting emissions of GHG from incubated agricultural soils.

    PubMed

    García-Marco, S; Ravella, S R; Chadwick, D; Vallejo, A; Gregory, A S; Cárdenas, L M

    2014-07-01

    Agriculture significantly contributes to global greenhouse gas (GHG) emissions and there is a need to develop effective mitigation strategies. The efficacy of methods to reduce GHG fluxes from agricultural soils can be affected by a range of interacting management and environmental factors. Uniquely, we used the Taguchi experimental design methodology to rank the relative importance of six factors known to affect the emission of GHG from soil: nitrate (NO 3 - ) addition, carbon quality (labile and non-labile C), soil temperature, water-filled pore space (WFPS) and extent of soil compaction. Grassland soil was incubated in jars where selected factors, considered at two or three amounts within the experimental range, were combined in an orthogonal array to determine the importance and interactions between factors with a L 16 design, comprising 16 experimental units. Within this L 16 design, 216 combinations of the full factorial experimental design were represented. Headspace nitrous oxide (N 2 O), methane (CH 4 ) and carbon dioxide (CO 2 ) concentrations were measured and used to calculate fluxes. Results found for the relative influence of factors (WFPS and NO 3 - addition were the main factors affecting N 2 O fluxes, whilst glucose, NO 3 - and soil temperature were the main factors affecting CO 2 and CH 4 fluxes) were consistent with those already well documented. Interactions between factors were also studied and results showed that factors with little individual influence became more influential in combination. The proposed methodology offers new possibilities for GHG researchers to study interactions between influential factors and address the optimized sets of conditions to reduce GHG emissions in agro-ecosystems, while reducing the number of experimental units required compared with conventional experimental procedures that adjust one variable at a time.

  13. Ranking factors affecting emissions of GHG from incubated agricultural soils

    PubMed Central

    García-Marco, S; Ravella, S R; Chadwick, D; Vallejo, A; Gregory, A S; Cárdenas, L M

    2014-01-01

    Agriculture significantly contributes to global greenhouse gas (GHG) emissions and there is a need to develop effective mitigation strategies. The efficacy of methods to reduce GHG fluxes from agricultural soils can be affected by a range of interacting management and environmental factors. Uniquely, we used the Taguchi experimental design methodology to rank the relative importance of six factors known to affect the emission of GHG from soil: nitrate (NO3−) addition, carbon quality (labile and non-labile C), soil temperature, water-filled pore space (WFPS) and extent of soil compaction. Grassland soil was incubated in jars where selected factors, considered at two or three amounts within the experimental range, were combined in an orthogonal array to determine the importance and interactions between factors with a L16 design, comprising 16 experimental units. Within this L16 design, 216 combinations of the full factorial experimental design were represented. Headspace nitrous oxide (N2O), methane (CH4) and carbon dioxide (CO2) concentrations were measured and used to calculate fluxes. Results found for the relative influence of factors (WFPS and NO3− addition were the main factors affecting N2O fluxes, whilst glucose, NO3− and soil temperature were the main factors affecting CO2 and CH4 fluxes) were consistent with those already well documented. Interactions between factors were also studied and results showed that factors with little individual influence became more influential in combination. The proposed methodology offers new possibilities for GHG researchers to study interactions between influential factors and address the optimized sets of conditions to reduce GHG emissions in agro-ecosystems, while reducing the number of experimental units required compared with conventional experimental procedures that adjust one variable at a time. PMID:25177207

  14. Angular dependence models for radiance to flux conversion

    NASA Technical Reports Server (NTRS)

    Green, Richard N.; Suttles, John T.; Wielicki, Bruce A.

    1990-01-01

    Angular dependence models (ADM) used for converting the measured radiance to flux at the top of the atmosphere are reviewed, and emphasis is placed on the measure of their effectiveness and the implications of requiring the ADMs to satisfy reciprocity. The overall significance of the ADMs is figured out by analyzing the same satellite data with a single Lambertian model, single mean model, and the 12 Earth Radiation Budget Experiment (ERBE) ADMs. It is shown that the Lambertian ADM is inadequate, while the mean ADM results in nearly unbiased fluxes but creates substantial differences for individual pixel fluxes. The standard ERBE ADM works well except for a 10-pct to 15-pct albedo growth across the scan; a modified ADM based on the standard ERBE ADM but forced to satisfy the principle of reciprocity increases the limb brightening and reduces the albedo growth but does not improve the scanner and nonscanner intercomparison.

  15. Surface roughness considerations for atmospheric correction of ocean color sensors. I - The Rayleigh-scattering component. II - Error in the retrieved water-leaving radiance

    NASA Technical Reports Server (NTRS)

    Gordon, Howard R.; Wang, Menghua

    1992-01-01

    The first step in the Coastal Zone Color Scanner (CZCS) atmospheric-correction algorithm is the computation of the Rayleigh-scattering (RS) contribution, L sub r, to the radiance leaving the top of the atmosphere over the ocean. In the present algorithm, L sub r is computed by assuming that the ocean surface is flat. Calculations of the radiance leaving an RS atmosphere overlying a rough Fresnel-reflecting ocean are presented to evaluate the radiance error caused by the flat-ocean assumption. Simulations are carried out to evaluate the error incurred when the CZCS-type algorithm is applied to a realistic ocean in which the surface is roughened by the wind. In situations where there is no direct sun glitter, it is concluded that the error induced by ignoring the Rayleigh-aerosol interaction is usually larger than that caused by ignoring the surface roughness. This suggests that, in refining algorithms for future sensors, more effort should be focused on dealing with the Rayleigh-aerosol interaction than on the roughness of the sea surface.

  16. BOREAS RSS-20 POLDER Radiance Images From the NASA C-130

    NASA Technical Reports Server (NTRS)

    Leroy, M.; Hall, Forrest G. (Editor); Nickeson, Jaime (Editor); Smith, David E. (Technical Monitor)

    2000-01-01

    These Boreal Ecosystem-Atmosphere Study (BOREAS) Remote Sensing Science (RSS)-20 data are a subset of images collected by the Polarization and Directionality of Earth's Reflectance (POLDER) instrument over tower sites in the BOREAS study areas during the intensive field campaigns (IFCs) in 1994. The POLDER images presented here from the NASA ARC C-130 aircraft are made available for illustration purposes only. The data are stored in binary image-format files. The POLDER radiance images are available from the Earth Observing System Data and Information System (EOSDIS) Oak Ridge National Laboratory (ORNL) Distributed Active Archive Center (DAAC). The data files are available on a CD-ROM (see document number 20010000884).

  17. Reviews on factors affecting fatigue behavior of high-Mn steels

    NASA Astrophysics Data System (ADS)

    Kim, Sangshik; Jeong, Daeho; Sung, Hyokyung

    2018-01-01

    A variety of factors affect the fatigue behavior of high-Mn steels, which include both extrinsic (i.e., loading type, R ratio, specimen type, surface condition, temperature, and environment) and intrinsic (i.e., chemical composition, grain size, microstructure, stacking fault energy) factors. Very often, the influence of extrinsic factors on the fatigue behavior is even greater than that of intrinsic factors, misleading the interpretation of fatigue data. The metallurgical factors influence the initiation and propagation behaviors of fatigue by altering the characteristics of slip that is prerequisite for fatigue damage accumulation. It is however not easy to separate the effect of each factor since they affect the fatigue behavior of high-Mn steels in complex and synergistic way. In this review, the fatigue data of high-Mn steels are summarized and the factors complicating the interpretation are discussed.

  18. Review: Factors affecting fouling in conventional pens for slaughter pigs.

    PubMed

    Larsen, M L V; Bertelsen, M; Pedersen, L J

    2018-02-01

    This review assesses factors affecting fouling in conventional pens for slaughter pigs. Fouling of the pen happens when pigs change their excretory behaviour from occurring in the designated dunging area to the lying area. This can result in a lower hygiene, bad air quality, extra work for the farmer, disturbance of the pigs' resting behaviour and an increase in agonistic interactions. A systematic search was conducted and results narrowed down to 21 articles. Four factors were found to affect fouling directly: insufficient space allowance, the flooring design of the pen, the thermal climate and pigs' earlier experience. Further, these primary factors are affected by secondary factors such as the shape of the pen, the weight of the pigs and especially the heat balance of the pigs, which is affected by several tertiary factors including, for example, temperature, humidity and draught. Results indicate that the most important factor to control when trying to prevent fouling of a pen is the pen climate. An appropriate climate may be accomplished through floor cooling in the designated lying area, sprinklers above the designated dunging area and by ensuring a more optimal ambient temperature curve that also fits the weight of the pigs in different stages of the production. All in all, fouling of the pen in conventional slaughter pigs is a multifactorial problem, but it is important to focus on increasing the comfortability, and especially the climate, of the designated lying area.

  19. Factors affecting the quality of life in childhood epilepsy in China.

    PubMed

    Yong, L; Chengye, J; Jiong, Q

    2006-03-01

    To explore the level of, and factors affecting the quality of life (QOL) in childhood epilepsy in China. At the Peking University First Hospital, we consecutively identified 418 parents whose children were with known epilepsy to complete a questionnaire, which included children's demographic characteristics, clinical message of epilepsy, QOL, familial message, parental symptoms of anxiety/depression. Significant (p<0.05) affecting factors of children's quality of life included current educational degree, mental development, age at diagnosis, age at onset, seizure frequency, duration, AED number; parental significant (p<0.05) affecting factors included anxiety, depression and health. On regression analysis, parental anxiety was the most important factor in explaining lower QOL in childhood epilepsy. AEDs, familial economic state, paternal career, seizure frequency were also significant factors. Parental anxiety outweighed the physical factors in determining QOL in childhood epilepsy. Recognition of this will be helpful for professionals to treat disease and improve the QOL of childhood epilepsy.

  20. Accounting for the water-leaving radiance in the simultaneous retrieval of atmosphere and ocean properties from collocated polarimeters and lidar measurements: results for the SABOR campaign

    NASA Astrophysics Data System (ADS)

    Chowdhary, J.; Brian, C.; Stamnes, S.; Hostetler, C. A.; Cetinic, I.; Slade, W. H.; Hu, Y.

    2017-12-01

    Ocean spectra typically contribute less than 10% to top-of-atmosphere (TOA) radiance observations in the visible (VIS). The remaining 90% of TOA radiance originates from scattering in the atmosphere which needs to be removed (i.e. corrected) but varies substantially with the aerosol present at the time of observation. The traditional approach for atmospheric correction (AC), used for ocean color sensors such as SeaWiFS, MODIS, and VIIRS, estimates aerosol scattering properties from TOA radiance observations in the near-infrared/short-wave infrared (NIR/SWIR) where the ocean becomes dark. The aerosol model is subsequently used to compute the atmospheric scattering contribution to the TOA radiance in the VIS. The final step is to subtract this computed scattering contribution from the real (i.e. observed) TOA radiance. As an alternative to the traditional approach for AC, we retrieve the atmosphere (i.e., aerosol) and ocean (i.e., color) properties simultaneously from measurements in the VIS. To separate the information content for the atmosphere and ocean, we use lidar measurements and multi-angle polarization measurements. Lidar and polarimeter measurements are powerful tools to enhance the ocean product retrievals from conventional ocean color sensors, and are under consideration to accompany future generation ocean color sensors. Here, we present results of simultaneous atmosphere-ocean retrievals using collocated airborne lidar and polarimeter data that were acquired during the Ship-Aircraft Bio-Optical Research (SABOR) campaign. We discuss 2 hydrosol models (which differ in number of free parameters) that were used for these inversions. We then compare our ocean retrievals with measurements obtained from the accompanying cruise ship. Finally, we touch upon a next generation of hydrosol models that accommodates the unique sensitivity of ocean lidar profiles to plankton morphology.

  1. Factors affecting academic leadership in dermatology.

    PubMed

    Martires, Kathryn J; Aquino, Lisa L; Wu, Jashin J

    2015-02-01

    Although prior studies have examined methods by which to recruit and retain academic dermatologists, few have examined factors that are important for developing academic leaders in dermatology. This study sought to examine characteristics of dermatology residency programs that affect the odds of producing department or division chairs/chiefs and program directors (PDs). Data regarding program size, faculty, grants, alumni residency program attended, lectures, and publications for all accredited US dermatology residency programs were collected. Of the 103 programs examined, 46% had graduated at least 1 chair/chief, and 53% had graduated at least 1 PD. Results emphasize that faculty guidance and research may represent modifiable factors by which a dermatology residency program can increase its graduation of academic leaders.

  2. Assessment of Forecast Sensitivity to Observation and Its Application to Satellite Radiances

    NASA Astrophysics Data System (ADS)

    Ide, K.

    2017-12-01

    The Forecast sensitivity to observation provides practical and useful metric for the assessment of observation impact without conducting computationally intensive data denial experiments. Quite often complex data assimilation systems use a simplified version of the forecast sensitivity formulation based on ensembles. In this talk, we first present the comparison of forecast sensitivity for 4DVar, Hybrid-4DEnVar, and 4DEnKF with or without such simplifications using a highly nonlinear model. We then present the results of ensemble forecast sensitivity to satellite radiance observations for Hybrid-4DEnVart using NOAA's Global Forecast System.

  3. 78 FR 46418 - Proposed Information Collection (Obligation To Report Factors Affecting Entitlement) Activity...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-07-31

    ... (Obligation To Report Factors Affecting Entitlement) Activity; Comment Request AGENCY: Veterans Benefits... use of other forms of information technology. Title: Obligation to Report Factors Affecting... entitlement factors. Individual factors such as income, marital status, and the beneficiary's number of...

  4. 75 FR 62634 - Proposed Information Collection (Obligation to Report Factors Affecting Entitlement) Activity...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-10-12

    ... (Obligation to Report Factors Affecting Entitlement) Activity: Comment Request AGENCY: Veterans Benefits... use of other forms of information technology. Title: Obligation to Report Factors Affecting... entitlement factors. Individual factors such as income, marital status, and the beneficiary's number of...

  5. Analysis of factors affecting employee satisfaction: A case study from Pakistan.

    PubMed

    Rukh, Lala; Choudhary, Muhammad Abbas; Abbasi, Saddam Akber

    2015-01-01

    Employee job satisfaction has been a research focal point throughout the world. It is a key factor when measuring the performance of an organization and individuals. A leading engineering goods manufacturing enterprise in Pakistan, has been used in this case study. In Pakistan, very limited research has been done with respect to factors affecting job satisfaction. Some research has been done in medical institutions, banks, universities and the information technology sector but large public sector organizations in Pakistan have not been studied. A theoretical foundation for researching factors affecting job satisfaction in large organizations is outlined. The objective of this research is to analyze various demographic, financial and non-financial factors affecting the satisfaction level of employees and to study the effects across different employee groups. This study is based on quantitative data analysis. The employees of the organization under study have been divided into 10 homogeneous groups based on their departments. Information on job related factors (affecting the satisfaction level) have been collected from subsamples of each group using a self-administered questionnaire. An overall sample of 250 (out of total 1100) employees has been selected. Before conducting the survey, reliability of the questionnaire was measured using Cronbach's alpha. The normality of data was also examined using the Kolmogorov Smirnov test. Hypotheses devised to address the research questions were tested by using non-parametric Spearman correlation and Kruskal-Wallis tests. The response rate was 73.2%. Research findings indicated the significant factors that affect the satisfaction level of employees. Median group differences existed between responses based on age, work experience, salary and designation (i.e. job position/rank) of employees. Job satisfaction was also positively and significantly associated with job related factors such as pay, promotion, relation with employees

  6. Factors Affecting Successful Implementation of Hospital Information Systems.

    PubMed

    Farzandipur, Mehrdad; Jeddi, Fatemeh Rangraz; Azimi, Esmaeil

    2016-02-01

    Today, the use of information systems in health environments, like any other fields, is necessary and organizational managers are convinced to use these systems. However, managers' satisfaction is not the only factor in successfully implementing these systems and failed information technology projects (IT) are reported despite the consent of the directors. Therefore, this study aims to determine the factors affecting the successful implementation of a hospital information system. The study was carried out as a descriptive method in 20 clinical hospitals that the hospital information system (HIS) was conducted in them. The clinical and paraclinical users of mentioned hospitals are the study group. 400 people were chosen as samples in scientific method and the data was collected using a questionnaire consisted of three main human, managerial and organizational, and technological factors, by questionnaire and interview. Then the data was scored in Likert scale (score of 1 to 5) and were analyzed using the SPSS software. About 75 percent of the population were female, with average work experience of 10 years and the mean age was 30 years. The human factors affecting the success of hospital information system implementation achieved the mean score of 3.5, both organizational and managerial factors 2.9 and technological factors the mean of 3. Human factors including computer skills, perceiving usefulness and perceiving the ease of a hospital information system use are more effective on the acceptance and successful implementation of hospital information systems; then the technological factors play a greater role. It is recommended that for the successful implementation of hospital information systems, most of these factors to be considered.

  7. Factors Affecting Open-Set Word Recognition in Adults with Cochlear Implants

    PubMed Central

    Holden, Laura K.; Finley, Charles C.; Firszt, Jill B.; Holden, Timothy A.; Brenner, Christine; Potts, Lisa G.; Gotter, Brenda D.; Vanderhoof, Sallie S.; Mispagel, Karen; Heydebrand, Gitry; Skinner, Margaret W.

    2012-01-01

    A monosyllabic word test was administered to 114 postlingually-deaf adult cochlear implant (CI) recipients at numerous intervals from two weeks to two years post-initial CI activation. Biographic/audiologic information, electrode position, and cognitive ability were examined to determine factors affecting CI outcomes. Results revealed that Duration of Severe-to-Profound Hearing Loss, Age at Implantation, CI Sound-field Threshold Levels, Percentage of Electrodes in Scala Vestibuli, Medio-lateral Electrode Position, Insertion Depth, and Cognition were among the factors that affected performance. Knowledge of how factors affect performance can influence counseling, device fitting, and rehabilitation for patients and may contribute to improved device design. PMID:23348845

  8. Factors affecting self-regulated learning in medical students: a qualitative study

    PubMed Central

    Jouhari, Zahra; Haghani, Fariba; Changiz, Tahereh

    2015-01-01

    Introduction Clinical courses are required of all medical students and means that they must develop the key skill of self-regulation during learning. The ability to self-regulate learning strategies is affected by different factors. This study determined the views of medical students on the factors affecting self-regulated learning (SRL). Method This study uses a qualitative approach and the content analysis method. Nineteen medical students in their fourth, fifth, and sixth years of study at Isfahan University of Medical Science participated in semi-structured, in-depth interviews. The students were selected using purposive sampling based on their overall grade point average (GPA). Results Five main themes were found to affect SRL. These themes included family with the two subthemes of family supervisory and supportive roles; peers with the two subthemes of facilitating and inhibiting roles; instructors with the two subthemes of personal and educational instructor's characteristics; educational environment with the two subthemes of facilitator and inhibitor roles; and student with the two subthemes of facilitating and inhibiting personal factors. Conclusion The outcomes of student understanding of the factors affecting self-regulation indicate that facilitating factors should be used on an individual basis to reduce the effect of inhibiting factors to improve self-regulation in students. PMID:26549046

  9. Factors affecting self-regulated learning in medical students: a qualitative study.

    PubMed

    Jouhari, Zahra; Haghani, Fariba; Changiz, Tahereh

    2015-01-01

    Introduction Clinical courses are required of all medical students and means that they must develop the key skill of self-regulation during learning. The ability to self-regulate learning strategies is affected by different factors. This study determined the views of medical students on the factors affecting self-regulated learning (SRL). Method This study uses a qualitative approach and the content analysis method. Nineteen medical students in their fourth, fifth, and sixth years of study at Isfahan University of Medical Science participated in semi-structured, in-depth interviews. The students were selected using purposive sampling based on their overall grade point average (GPA). Results Five main themes were found to affect SRL. These themes included family with the two subthemes of family supervisory and supportive roles; peers with the two subthemes of facilitating and inhibiting roles; instructors with the two subthemes of personal and educational instructor's characteristics; educational environment with the two subthemes of facilitator and inhibitor roles; and student with the two subthemes of facilitating and inhibiting personal factors. Conclusion The outcomes of student understanding of the factors affecting self-regulation indicate that facilitating factors should be used on an individual basis to reduce the effect of inhibiting factors to improve self-regulation in students.

  10. Factors affecting self-regulated learning in medical students: a qualitative study.

    PubMed

    Jouhari, Zahra; Haghani, Fariba; Changiz, Tahereh

    2015-01-01

    Clinical courses are required of all medical students and means that they must develop the key skill of self-regulation during learning. The ability to self-regulate learning strategies is affected by different factors. This study determined the views of medical students on the factors affecting self-regulated learning (SRL). This study uses a qualitative approach and the content analysis method. Nineteen medical students in their fourth, fifth, and sixth years of study at Isfahan University of Medical Science participated in semi-structured, in-depth interviews. The students were selected using purposive sampling based on their overall grade point average (GPA). Five main themes were found to affect SRL. These themes included family with the two subthemes of family supervisory and supportive roles; peers with the two subthemes of facilitating and inhibiting roles; instructors with the two subthemes of personal and educational instructor's characteristics; educational environment with the two subthemes of facilitator and inhibitor roles; and student with the two subthemes of facilitating and inhibiting personal factors. The outcomes of student understanding of the factors affecting self-regulation indicate that facilitating factors should be used on an individual basis to reduce the effect of inhibiting factors to improve self-regulation in students.

  11. 14 CFR Appendix B to Part 1215 - Factors Affecting Standard Charges

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 14 Aeronautics and Space 5 2011-01-01 2010-01-01 true Factors Affecting Standard Charges B Appendix B to Part 1215 Aeronautics and Space NATIONAL AERONAUTICS AND SPACE ADMINISTRATION TRACKING AND DATA RELAY SATELLITE SYSTEM (TDRSS) Pt. 1215, App. B Appendix B to Part 1215—Factors Affecting Standard...

  12. Methods of Combinatorial Optimization to Reveal Factors Affecting Gene Length

    PubMed Central

    Bolshoy, Alexander; Tatarinova, Tatiana

    2012-01-01

    In this paper we present a novel method for genome ranking according to gene lengths. The main outcomes described in this paper are the following: the formulation of the genome ranking problem, presentation of relevant approaches to solve it, and the demonstration of preliminary results from prokaryotic genomes ordering. Using a subset of prokaryotic genomes, we attempted to uncover factors affecting gene length. We have demonstrated that hyperthermophilic species have shorter genes as compared with mesophilic organisms, which probably means that environmental factors affect gene length. Moreover, these preliminary results show that environmental factors group together in ranking evolutionary distant species. PMID:23300345

  13. CORSAIR-Calibrated Observations of Radiance Spectra from the Atmosphere in the Far- Infrared

    NASA Astrophysics Data System (ADS)

    Mlynczak, M. G.; Johnson, D.; Abedin, N.; Liu, X.; Kratz, D.; Jordan, D.; Wang, J.; Bingham, G.; Latvakoski, H.; Bowman, K.; Kaplan, S.

    2008-12-01

    The CORSAIR project is a new NASA Instrument Incubator Project (IIP) whose primary goal is to develop and demonstrate the necessary technologies to achieve SI-traceable, on-orbit measurements of Earth's spectral radiance in the far-infrared (far-IR). The far-IR plays a vital role in the energy balance of the Earth yet its spectrum has not been comprehensively observed from space for the purposes of climate sensing. The specific technologies being developed under CORSAIR include: passively cooled, antenna-coupled terahertz detectors for the far-IR (by Raytheon Vision Systems); accurately calibrated, SI-traceable blackbody sources for the far-IR (by Space Dynamics Laboratory); and high-performance broad bandpass beamsplitters (by ITT). These technologies complement those already developed under past Langley IIP projects (FIRST; INFLAME) in the areas of Fourier Transform Spectrometers and dedicated far-IR beamsplitters. The antenna-coupled far-IR detectors will be validated in the FIRST instrument at Langley. The SI-traceable far-IR blackbodies will be developed in conjunction with the National Institute of Standards and Technology (NIST). An overview of the CORSAIR technologies will be presented as well as their larger role in the Climate Absolute Radiance and Refractivity Observatory (CLARREO) mission. Upon successful completion of CORSAIR these IIP efforts will provide the necessary technologies to achieve the first comprehensive, accurate, high-resolution measurements from a satellite of the far-IR spectrum of the Earth and its atmosphere, enabling major advances in our understanding of Earth's climate.

  14. The Relationship Between X-Ray Radiance and Magnetic Flux

    NASA Astrophysics Data System (ADS)

    Pevtsov, Alexei A.; Fisher, George H.; Acton, Loren W.; Longcope, Dana W.; Johns-Krull, Christopher M.; Kankelborg, Charles C.; Metcalf, Thomas R.

    2003-12-01

    We use soft X-ray and magnetic field observations of the Sun (quiet Sun, X-ray bright points, active regions, and integrated solar disk) and active stars (dwarf and pre-main-sequence) to study the relationship between total unsigned magnetic flux, Φ, and X-ray spectral radiance, LX. We find that Φ and LX exhibit a very nearly linear relationship over 12 orders of magnitude, albeit with significant levels of scatter. This suggests a universal relationship between magnetic flux and the power dissipated through coronal heating. If the relationship can be assumed linear, it is consistent with an average volumetric heating rate Q~B/L, where B is the average field strength along a closed field line and L is its length between footpoints. The Φ-LX relationship also indicates that X-rays provide a useful proxy for the magnetic flux on stars when magnetic measurements are unavailable.

  15. Factors Affecting Smoking Tendency and Smoking Intensity

    ERIC Educational Resources Information Center

    David, Nissim Ben; Zion, Uri Ben

    2009-01-01

    Purpose: The purpose of this paper is to measure the relative effect of relevant explanatory variable on smoking tendency and smoking intensity. Design/methodology/approach: Using survey data collected by the Israeli Bureau of Statistics in 2003-2004, a probit procedure is estimated for analyzing factors that affect the probability of being a…

  16. Using radiance predicted by the P3 approximation in a spherical geometry to predict tissue optical properties

    NASA Astrophysics Data System (ADS)

    Dickey, Dwayne J.; Moore, Ronald B.; Tulip, John

    2001-01-01

    For photodynamic therapy of solid tumors, such as prostatic carcinoma, to be achieved, an accurate model to predict tissue parameters and light dose must be found. Presently, most analytical light dosimetry models are fluence based and are not clinically viable for tissue characterization. Other methods of predicting optical properties, such as Monet Carlo, are accurate but far too time consuming for clinical application. However, radiance predicted by the P3-Approximation, an anaylitical solution to the transport equation, may be a viable and accurate alternative. The P3-Approximation accurately predicts optical parameters in intralipid/methylene blue based phantoms in a spherical geometry. The optical parameters furnished by the radiance, when introduced into fluence predicted by both P3- Approximation and Grosjean Theory, correlate well with experimental data. The P3-Approximation also predicts the optical properties of prostate tissue, agreeing with documented optical parameters. The P3-Approximation could be the clinical tool necessary to facilitate PDT of solid tumors because of the limited number of invasive measurements required and the speed in which accurate calculations can be performed.

  17. Synergistic use of MODIS cloud products and AIRS radiance measurements for retrieval of cloud parameters

    NASA Astrophysics Data System (ADS)

    Li, J.; Menzel, W.; Sun, F.; Schmit, T.

    2003-12-01

    The Moderate-Resolution Imaging Spectroradiometer (MODIS) and Atmospheric Infrared Sounder (AIRS) measurements from the Earth Observing System's (EOS) Aqua satellite will enable global monitoring of the distribution of clouds. MODIS is able to provide at high spatial resolution (1 ~ 5km) the cloud mask, surface and cloud types, cloud phase, cloud-top pressure (CTP), effective cloud amount (ECA), cloud particle size (CPS), and cloud water path (CWP). AIRS is able to provide CTP, ECA, CPS, and CWP within the AIRS footprint with much better accuracy using its greatly enhanced hyperspectral remote sensing capability. The combined MODIS / AIRS system offers the opportunity for cloud products improved over those possible from either system alone. The algorithm developed was applied to process the AIRS longwave cloudy radiance measurements; results are compared with MODIS cloud products, as well as with the Geostationary Operational Environmental Satellite (GOES) sounder cloud products, to demonstrate the advantage of synergistic use of high spatial resolution MODIS cloud products and high spectral resolution AIRS sounder radiance measurements for optimal cloud retrieval. Data from ground-based instrumentation at the Atmospheric Radiation Measurement (ARM) Program Cloud and Radiation Test Bed (CART) in Oklahoma were used for the validation; results show that AIRS improves the MODIS cloud products in certain cases such as low-level clouds.

  18. User's guide: Nimbus-7 Earth radiation budget narrow-field-of-view products. Scene radiance tape products, sorting into angular bins products, and maximum likelihood cloud estimation products

    NASA Technical Reports Server (NTRS)

    Kyle, H. Lee; Hucek, Richard R.; Groveman, Brian; Frey, Richard

    1990-01-01

    The archived Earth radiation budget (ERB) products produced from the Nimbus-7 ERB narrow field-of-view scanner are described. The principal products are broadband outgoing longwave radiation (4.5 to 50 microns), reflected solar radiation (0.2 to 4.8 microns), and the net radiation. Daily and monthly averages are presented on a fixed global equal area (500 sq km), grid for the period May 1979 to May 1980. Two independent algorithms are used to estimate the outgoing fluxes from the observed radiances. The algorithms are described and the results compared. The products are divided into three subsets: the Scene Radiance Tapes (SRT) contain the calibrated radiances; the Sorting into Angular Bins (SAB) tape contains the SAB produced shortwave, longwave, and net radiation products; and the Maximum Likelihood Cloud Estimation (MLCE) tapes contain the MLCE products. The tape formats are described in detail.

  19. Remote Determination of Cloud Temperature and Transmittance from Spectral Radiance Measurements: Method and Results

    DTIC Science & Technology

    1996-10-01

    CENTRE DE RECHERCHES POUR LA DEFENSE VALCARTIER,QuEBEC DREV - R - 9608 Unlimited Distribution I Distribution illimitee REMOTE DETERMINATION OF...propose une methode d’evaluation de la temperature et de la transmittance des nuages en se basant sur des mesures de radiance spectrale effectuees au...niveau du sol. Cette methode tire avantage du fait qu’il y a une forte bande d’emission de l’ozone a 9.6 J!ffi, ce qui constitue une source naturelle

  20. Identification of Factors That Affect Software Complexity.

    ERIC Educational Resources Information Center

    Kaiser, Javaid

    A survey of computer scientists was conducted to identify factors that affect software complexity. A total of 160 items were selected from the literature to include in a questionnaire sent to 425 individuals who were employees of computer-related businesses in Lawrence and Kansas City. The items were grouped into nine categories called system…

  1. INTERNATIONAL DIFFERENCES IN FACTORS AFFECTING LABOUR MOBILITY.

    ERIC Educational Resources Information Center

    SELLIER, F.; ZARKA, C.

    THE GEOGRAPHICAL, OCCUPATIONAL, AND INTERFIRM MOBILITY, AND THE FACTORS AFFECTING THESE MOVEMENTS FOR WORKERS IN FRANCE, ITALY, GERMANY, AND SWEDEN IN THE PERIOD SINCE THE SECOND WORLD WAR ARE STUDIED. DATA OBTAINED FROM INDUSTRIAL SURVEYS AND GENERAL CENSUSES WERE USED TO COMPARE THE FOUR COUNTRIES WITH EACH OTHER AND WITH THE UNITED STATES.…

  2. Downwelling Far-Infrared Radiance Spectra Measured by FIRST at Cerro Toco, Chile

    NASA Astrophysics Data System (ADS)

    Mast, J. C.; Mlynczak, M. G.; Cageao, R.; Kratz, D. P.; Latvakoski, H.; Johnson, D. G.; Mlawer, E. J.; Turner, D. D.

    2015-12-01

    The Far-Infrared Spectroscopy of the Troposphere (FIRST) instrument is a Fourier transform spectrometer developed by NASA Langley Research Center in collaboration with the Space Dynamics Laboratory and the Harvard-Smithsonian Center for Astrophysics. FIRST was initially developed for measuring the far-infrared portion of Earth's longwave spectrum as a balloon borne instrument and later was reconfigured to operate as a ground-based instrument. In its current ground-based configuration FIRST was deployed at 17500 ft on Cerro Toco, a mountain in the Atacama Desert of Chile, from August to October, 2009. There the integrated precipitable water (IPW) was as low as 0.02 cm. FIRST measurements from days with IPW between 0.024 and 0.035 cm during the campaign are presented here between 200 cm-1 and 800 cm-1. Significant spectral development in the far-IR is observed over the entire 200 cm-1 to 800 cm-1 band. Water vapor and temperature profiles from radiosonde and GVRP measurements are used as inputs to the AER Line-by-Line Radiative Transfer Model (LBLRTM) utilizing the AER v3.2 line parameter database. Uncertainties in both the measured and modeled radiances are accounted for in this study. The residual LBLRTM - FIRST is calculated to assess agreement between the measured and modeled spectra. Measured and model radiances generally agree to within the combined uncertainties for wavenumbers greater than 360 cm-1. At wavenumbers less than 360 cm-1 persistent troughs in the residual are present outside of the combined uncertainties. These features are present on different days and at different water vapor amounts. Possible solutions for these features are discussed.

  3. BOREAS RSS-2 Level-1B ASAS Image Data: At-Sensor Radiance in BSQ Format

    NASA Technical Reports Server (NTRS)

    Russell, C.; Hall, Forrest G. (Editor); Nickeson, Jaime (Editor); Dabney, P. W.; Kovalick, W.; Graham, D.; Bur, Michael; Irons, James R.; Tierney, M.

    2000-01-01

    The BOREAS RSS-2 team used the ASAS instrument, mounted on the NASA C-130 aircraft, to create at-sensor radiance images of various sites as a function of spectral wavelength, view geometry (combinations of view zenith angle, view azimuth angle, solar zenith angle, and solar azimuth angle), and altitude. The level-1b ASAS images of the BOREAS study areas were collected from April to September 1994 and March to July 1996.

  4. A Metasynthesis of Factors Affecting Self-Management of Chronic Illness

    PubMed Central

    SCHULMAN-GREEN, Dena; JASER, Sarah S.; PARK, Chorong; WHITTEMORE, Robin

    2015-01-01

    Aim To identify factors that may serve as facilitators and barriers to self-management described by adults living with chronic illness by conducting a qualitative metasynthesis. Background Self-management is an individuals’ active management of a chronic illness in collaboration with their family members and clinicians. Design Qualitative metasynthesis. Data Sources We analyzed studies (N=53) published between January 2000–May 2013 that described factors affecting self-management in chronic illness as reported by adults aged over 18 years with chronic illness. Review Methods Sandelowsi and Barroso approach to qualitative metasynthesis: literature search; quality appraisal; analysis; and synthesis of findings. Results Collectively, article authors reported on sixteen chronic illnesses, most commonly diabetes (N=28) and cardiovascular disease (N=20). Participants included men and women (mean age=57, range 18–94) from twenty countries representing diverse races and ethnicities. We identified five categories of factors affecting self-management: Personal/Lifestyle Characteristics; Health Status; Resources; Environmental Characteristics; and Health Care System. Factors may interact to affect self-management and may exist on a continuum of positive (facilitator) to negative (barrier). Conclusion Understanding factors that influence self-management may improve assessment of self-management among adults with chronic illness and may inform interventions tailored to meet individuals’ needs and improve health outcomes. PMID:26781649

  5. Factors affecting post-pubertal penile size in patients with hypospadias.

    PubMed

    Moriya, Kimihiko; Nakamura, Michiko; Nishimura, Yoko; Kitta, Takeya; Kanno, Yukiko; Chiba, Hiroki; Kon, Masafumi; Shinohara, Nobuo

    2016-09-01

    To evaluate actual post-pubertal penile size and factors affecting it in hypospadias patients, we retrospectively reviewed medical charts. Hypospadias patients whose external genitalia were categorized into Tanner stage 5, and whose stretched penile length was evaluated at 15 years old or older from April 2008 to April 2015, were enrolled in the present study. Stretched penile length was measured by a single examiner. Actual post-pubertal stretched penile length and factors affecting the post-pubertal stretched penile length were estimated. Statistical analysis was performed using Mann-Whitney U test and univariate and multivariate linear regression models for the determination of independent factors. Thirty patients met the inclusion criteria. Median age at evaluation was 17.2 years. Thirteen and 17 had mild and severe hypospadias, respectively. Endocrinological abnormality was identified in 5. Multivariate analysis showed that the severity of hypospadias and endocrinological abnormality were significant factors affecting stretched penile length. Stretched penile length in 25 patients without endocrinological abnormality was significantly longer than that in those with endocrinological abnormality (p = 0.036). Among patients without endocrinological abnormality, stretched penile length in 13 with severe hypospadias was significantly shorter than that in 12 with mild hypospadias (p = 0.004). While the severity of hypospadias and endocrinological abnormality at post-pubertal evaluation were factors affecting post-pubertal penile size, stretched penile length in patients with severe hypospadias was shorter even in cases without endocrinological abnormality. These results suggest that severe hypospadias is not only a disorder of urethral development, but also a disorder of penile development.

  6. Factors affecting rotator cuff healing.

    PubMed

    Mall, Nathan A; Tanaka, Miho J; Choi, Luke S; Paletta, George A

    2014-05-07

    Several studies have noted that increasing age is a significant factor for diminished rotator cuff healing, while biomechanical studies have suggested the reason for this may be an inferior healing environment in older patients. Larger tears and fatty infiltration or atrophy negatively affect rotator cuff healing. Arthroscopic rotator cuff repair, double-row repairs, performing a concomitant acromioplasty, and the use of platelet-rich plasma (PRP) do not demonstrate an improvement in structural healing over mini-open rotator cuff repairs, single-row repairs, not performing an acromioplasty, or not using PRP. There is conflicting evidence to support postoperative rehabilitation protocols using early motion over immobilization following rotator cuff repair.

  7. Factors affecting corticosteroid concentrations in yellow-bellied marmots.

    PubMed

    Armitage, K B

    1991-01-01

    1. Bound and total corticosteroid concentrations of yellow-bellied marmots (Marmota flaviventris) were lowest in May after emergence from hibernation and peaked in August prior to immergence. 2. Total corticosteroids were affected by age but not by sex or reproductive status. 3. There was no consistent relationship between measures of population density and concentrations of corticosteroids; when a significant relationship occurred, only 22-34% of the variation was explained. 4. Social status and social behavior were the major factors affecting corticosteroid concentrations.

  8. Factors affecting Iran`s future. Final report

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Sinai, J.

    1993-05-28

    This study examines the factors affecting Iran`s future by focusing on the demographic, economic, and military trends in Iran and their impact on the country`s national security objectives in the next decade. The paper also assesses the implications of an economic embargo on Iran and potential Iranian threats to regional and United States national interests.

  9. Radiance calibration of the High Altitude Observatory white-light coronagraph on Skylab

    NASA Technical Reports Server (NTRS)

    Poland, A. I.; Macqueen, R. M.; Munro, R. H.; Gosling, J. T.

    1977-01-01

    The processing of over 35,000 photographs of the solar corona obtained by the white-light coronograph on Skylab is described. Calibration of the vast amount of data was complicated by temporal effects of radiation fog and latent image loss. These effects were compensated by imaging a calibration step wedge on each data frame. Absolute calibration of the wedge was accomplished through comparison with a set of previously calibrated glass opal filters. Analysis employed average characteristic curves derived from measurements of step wedges from many frames within a given camera half-load. The net absolute accuracy of a given radiance measurement is estimated to be 20%.

  10. Are Affective Factors a Good Predictor of Science Achievement? Examining the Role of Affective Factors Based on PISA 2006

    ERIC Educational Resources Information Center

    Ozel, Murat; Caglak, Serdar; Erdogan, Mehmet

    2013-01-01

    This study investigated how affective factors like attitude and motivation contribute to science achievement in PISA 2006 using linear structural modeling. The data set of PISA 2006 collected from 4942 fifteen-year-old Turkish students (2290 females, 2652 males) was used for the statistical analyses. A total of 42 selected items on a four point…

  11. Construction of a Matched Global Cloud and Radiance Product from LEO/GEO and EPIC Observations to Estimate Daytime Earth Radiation Budget from DSCOVR

    NASA Astrophysics Data System (ADS)

    Duda, D. P.; Khlopenkov, K. V.; Palikonda, R.; Khaiyer, M. M.; Minnis, P.; Su, W.; Sun-Mack, S.

    2016-12-01

    With the launch of the Deep Space Climate Observatory (DSCOVR), new estimates of the daytime Earth radiation budget can computed from a combination of measurements from the two Earth-observing sensors onboard the spacecraft, the Earth Polychromatic Imaging Camera (EPIC) and the National Institute of Standards and Technology Advanced Radiometer (NISTAR). Although these instruments can provide accurate top-of-atmosphere (TOA) radiance measurements, they lack sufficient resolution to provide details on small-scale surface and cloud properties. Previous studies have shown that these properties have a strong influence on the anisotropy of the radiation at the TOA, and ignoring such effects can result in large TOA-flux errors. To overcome these effects, high-resolution scene identification is needed for accurate Earth radiation budget estimation. Selected radiance and cloud property data measured and derived from several low earth orbit (LEO, including NASA Terra and Aqua MODIS, NOAA AVHRR) and geosynchronous (GEO, including GOES (east and west), METEOSAT, INSAT-3D, MTSAT-2, and HIMAWARI-8) satellite imagers were collected to create hourly 5-km resolution global composites of data necessary to compute angular distribution models (ADM) for reflected shortwave (SW) and longwave (LW) radiation. The satellite data provide an independent source of radiance measurements and scene identification information necessary to construct ADMs that are used to determine the daytime Earth radiation budget. To optimize spatial matching between EPIC measurements and the high-resolution composite cloud properties, LEO/GEO retrievals within the EPIC fields of view (FOV) are convolved to the EPIC point spread function (PSF) in a similar manner to the Clouds and the Earth's Radiant Energy System (CERES) Single Scanner Footprint TOA/Surface Fluxes and Clouds (SSF) product. Examples of the merged LEO/GEO/EPIC product will be presented, describing the chosen radiance and cloud properties and

  12. Construction of a Matched Global Cloud and Radiance Product from LEO/GEO and EPIC Observations to Estimate Daytime Earth Radiation Budget from DSCOVR

    NASA Technical Reports Server (NTRS)

    Duda, David P.; Khlopenkov, Konstantin V.; Thiemann, Mandana; Palikonda, Rabindra; Sun-Mack, Sunny; Minnis, Patrick; Su, Wenying

    2016-01-01

    With the launch of the Deep Space Climate Observatory (DSCOVR), new estimates of the daytime Earth radiation budget can be computed from a combination of measurements from the two Earth-observing sensors onboard the spacecraft, the Earth Polychromatic Imaging Camera (EPIC) and the National Institute of Standards and Technology Advanced Radiometer (NISTAR). Although these instruments can provide accurate top-of-atmosphere (TOA) radiance measurements, they lack sufficient resolution to provide details on small-scale surface and cloud properties. Previous studies have shown that these properties have a strong influence on the anisotropy of the radiation at the TOA, and ignoring such effects can result in large TOA-flux errors. To overcome these effects, high-resolution scene identification is needed for accurate Earth radiation budget estimation. Selected radiance and cloud property data measured and derived from several low earth orbit (LEO, including NASA Terra and Aqua MODIS, NOAA AVHRR) and geosynchronous (GEO, including GOES (east and west), METEOSAT, INSAT-3D, MTSAT-2, and HIMAWARI-8) satellite imagers were collected to create hourly 5-km resolution global composites of data necessary to compute angular distribution models (ADM) for reflected shortwave (SW) and longwave (LW) radiation. The satellite data provide an independent source of radiance measurements and scene identification information necessary to construct ADMs that are used to determine the daytime Earth radiation budget. To optimize spatial matching between EPIC measurements and the high-resolution composite cloud properties, LEO/GEO retrievals within the EPIC fields of view (FOV) are convolved to the EPIC point spread function (PSF) in a similar manner to the Clouds and the Earth's Radiant Energy System (CERES) Single Scanner Footprint TOA/Surface Fluxes and Clouds (SSF) product. Examples of the merged LEO/GEO/EPIC product will be presented, describing the chosen radiance and cloud properties and

  13. Factors affecting cardiac rehabilitation referral by physician specialty.

    PubMed

    Grace, Sherry L; Grewal, Keerat; Stewart, Donna E

    2008-01-01

    Cardiac rehabilitation (CR) is widely underutilized because of multiple factors including physician referral practices. Previous research has shown CR referral varies by type of provider, with cardiologists more likely to refer than primary care physicians. The objective of this study was to compare factors affecting CR referral in primary care physicians versus cardiac specialists. A cross-sectional survey of a stratified random sample of 510 primary care physicians and cardiac specialists (cardiologists or cardiovascular surgeons) in Ontario identified through the Canadian Medical Directory Online was administered. One hundred four primary care physicians and 81 cardiac specialists responded to the 26-item investigator-generated survey examining medical, demographic, attitudinal, and health system factors affecting CR referral. Primary care physicians were more likely to endorse lack of familiarity with CR site locations (P < .001), lack of standardized referral forms (P < .001), inconvenience (P = .04), program quality (P = .004), and lack of discharge communication from CR (P = .001) as factors negatively impacting CR referral practices than cardiac specialists. Cardiac specialists were significantly more likely to perceive that their colleagues and department would regularly refer patients to CR than primary care physicians (P < .001). Where differences emerged, primary care physicians were more likely to perceive factors that would impede CR referral, some of which are modifiable. Marketing CR site locations, provision of standardized referral forms, and ensuring discharge summaries are communicated to primary care physicians may improve their willingness to refer to CR.

  14. Retrieval of surface temperature by remote sensing. [of earth surface using brightness temperature of air pollutants

    NASA Technical Reports Server (NTRS)

    Gupta, S. K.; Tiwari, S. N.

    1976-01-01

    A simple procedure and computer program were developed for retrieving the surface temperature from the measurement of upwelling infrared radiance in a single spectral region in the atmosphere. The program evaluates the total upwelling radiance at any altitude in the region of the CO fundamental band (2070-2220 1/cm) for several values of surface temperature. Actual surface temperature is inferred by interpolation of the measured upwelling radiance between the computed values of radiance for the same altitude. Sensitivity calculations were made to determine the effect of uncertainty in various surface, atmospheric and experimental parameters on the inferred value of surface temperature. It is found that the uncertainties in water vapor concentration and surface emittance are the most important factors affecting the accuracy of the inferred value of surface temperature.

  15. Assimilation of Precipitation Measurement Missions Microwave Radiance Observations With GEOS-5

    NASA Technical Reports Server (NTRS)

    Jin, Jianjun; Kim, Min-Jeong; McCarty, Will; Akella, Santha; Gu, Wei

    2015-01-01

    The Global Precipitation Mission (GPM) Core Observatory satellite was launched in February, 2014. The GPM Microwave Imager (GMI) is a conically scanning radiometer measuring 13 channels ranging from 10 to 183 GHz and sampling between 65 S 65 N. This instrument is a successor to the Tropical Rainfall Measurement Mission (TRMM) Microwave Imager (TMI), which has observed 9 channels at frequencies ranging 10 to 85 GHz between 40 S 40 N since 1997. This presentation outlines the base procedures developed to assimilate GMI and TMI radiances in clear-sky conditions, including quality control methods, thinning decisions, and the estimation of, observation errors. This presentation also shows the impact of these observations when they are incorporated into the GEOS-5 atmospheric data assimilation system.

  16. Factors Affecting Radiologist's PACS Usage.

    PubMed

    Forsberg, Daniel; Rosipko, Beverly; Sunshine, Jeffrey L

    2016-12-01

    The purpose of this study was to determine if any of the factors radiologist, examination category, time of week, and week effect PACS usage, with PACS usage defined as the sequential order of computer commands issued by a radiologist in a PACS during interpretation and dictation. We initially hypothesized that only radiologist and examination category would have significant effects on PACS usage. Command logs covering 8 weeks of PACS usage were analyzed. For each command trace (describing performed activities of an attending radiologist interpreting a single examination), the PACS usage variables number of commands, number of command classes, bigram repetitiveness, and time to read were extracted. Generalized linear models were used to determine the significance of the factors on the PACS usage variables. The statistical results confirmed the initial hypothesis that radiologist and examination category affect PACS usage and that the factors week and time of week to a large extent have no significant effect. As such, this work provides direction for continued efforts to analyze system data to better understand PACS utilization, which in turn can provide input to enable optimal utilization and configuration of corresponding systems. These continued efforts were, in this work, exemplified by a more detailed analysis using PACS usage profiles, which revealed insights directly applicable to improve PACS utilization through modified system configuration.

  17. Cognitive Factors Affecting Freeze-like Behavior in Humans.

    PubMed

    Alban, Michael W; Pocknell, Victoria

    2017-01-01

    Contemporary research on survival-related defensive behaviors has identified physiological markers of freeze/flight/fight. Our research focused on cognitive factors associated with freeze-like behavior in humans. Study 1 tested if an explicit decision to freeze is associated with the psychophysiological state of freezing. Heart rate deceleration occurred when participants chose to freeze. Study 2 varied the efficacy of freezing relative to other defense options and found "freeze" was responsive to variations in the perceived effectiveness of alternative actions. Study 3 tested if individual differences in motivational orientation affect preference for a "freeze" option when the efficacy of options is held constant. A trend in the predicted direction suggested that naturally occurring cognitions led loss-avoiders to select "freeze" more often than reward-seekers. In combination, our attention to the cognitive factors affecting freeze-like behavior in humans represents a preliminary step in addressing an important but neglected research area.

  18. Factors affecting the use of hardwood flooring in urban rehabilitation

    Treesearch

    Robert L. Jr. Nevel; Robert L. Jr. Nevel

    1973-01-01

    The continued use of hardwood flooring in urban rehabilitation is being threatened. A study of the influences that determine the choice of flooring indicates that economic, physical, or technological factors dominate. Most factors affecting the use of hardwood flooring are related to cost, availability, and compatibility. Of these factors, time and cost of installation...

  19. Acceleration of Radiance for Lighting Simulation by Using Parallel Computing with OpenCL

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Zuo, Wangda; McNeil, Andrew; Wetter, Michael

    2011-09-06

    We report on the acceleration of annual daylighting simulations for fenestration systems in the Radiance ray-tracing program. The algorithm was optimized to reduce both the redundant data input/output operations and the floating-point operations. To further accelerate the simulation speed, the calculation for matrix multiplications was implemented using parallel computing on a graphics processing unit. We used OpenCL, which is a cross-platform parallel programming language. Numerical experiments show that the combination of the above measures can speed up the annual daylighting simulations 101.7 times or 28.6 times when the sky vector has 146 or 2306 elements, respectively.

  20. Factors Affecting Sleep Quality of Patients in Intensive Care Unit

    PubMed Central

    Bihari, Shailesh; Doug McEvoy, R.; Matheson, Elisha; Kim, Susan; Woodman, Richard J.; Bersten, Andrew D.

    2012-01-01

    Introduction: Sleep disturbance is a frequently overlooked complication of intensive care unit (ICU) stay. Aim: To evaluate sleep quality among patients admitted to ICU and investigate environmental and non-environmental factors that affect sleep quality in ICU. Methods: Over a 22-month period, we consecutively recruited patients who spent ≥ 2 nights post-endotracheal extubation in ICU and who were orientated to time, place, and person on the day of discharge. Self-reported sleep quality, according to a modified Freedman questionnaire, which provided data on self-reported ICU sleep quality in ICU and environmental factors affecting sleep quality in the ICU, were collected. We also investigated non-environmental factors, such as severity of illness, ICU interventions, and medications that can affect sleep quality. Results: Fifty males and 50 females were recruited with a mean (± SD) age of 65.1 ± 15.2 years. APACHE II score at admission to ICU was 18.1 ± 7.5 with duration of stay 6.7 ± 6.5days. Self-reported sleep quality score at home (1 = worst; 10 = best) was 7.0 ± 2.2; this decreased to 4.0 ± 1.7 during their stay in ICU (p < 0.001). In multivariate analysis with APACHE III as severity of illness (R2 = 0.25), factors [exp(b)(95% CI), p value] which significantly affected sleep in ICU were sex [0.37(0.19-0.72), p < 0.01], age and sex interaction [1.02(1.01-1.03), p < 0.01], bedside phone [0.92(0.87-0.97), p < 0.01], prior quality of sleep at home [1.30(1.05-1.62), p = 0.02], and use of steroids [0.82(0.69-0.98), p = 0.03] during the stay in ICU. Conclusion: Reduced sleep quality is a common problem in ICU with a multifactorial etiology. Citation: Bihari S; McEvoy RD; Kim S; Woodman RJ; Bersten AD. Factors affecting sleep quality of patients in intensive care unit. J Clin Sleep Med 2012;8(3):301-307. PMID:22701388

  1. An Analysis of Factors That Affect the Educational Performance of Agricultural Students

    ERIC Educational Resources Information Center

    Greenway, Gina

    2012-01-01

    Many factors contribute to student achievement. This study focuses on three areas: how students learn, how student personality type affects performance, and how course format affects performance outcomes. The analysis sought to improve understanding of the direction and magnitude with which each of these factors impacts student success. Improved…

  2. Assessment of Factor Affecting Institutional Performance: The Case of Wolaita Sodo University

    ERIC Educational Resources Information Center

    Shibru, Sintayehu; Bibiso, Mesfin; Ousman, Kedir

    2017-01-01

    The purpose of this study is to explore factors that affect institutional performance of Wolaita Sodo University. The study has identified middle level manager's perceptions toward institutional performance to indicate the key factors that seem to affect the performance of the university. Data were collected using structured questionnaires and…

  3. Factors affecting onset of puberty in Denizli province in Turkey.

    PubMed

    Semiz, Serap; Kurt, Funda; Kurt, Devrim Tanil; Zencir, Mehmet; Sevinç, Ozgür

    2009-01-01

    The relationship between the possible factors affecting pubertal onset and pubertal timing was investigated in the Denizli province in Turkey. A total number of 3311 subjects (1562 girls, 1749 boys) aged 6-16.5 years participated in this study. Body mass index (BMI) was calculated. Pubertal stages were assessed according to methods of Marshall and Tanner. Testicular volume was determined using Prader orchidometer. Menarcheal age was recorded. All parents and students completed different questionnaires on demographic variables affecting pubertal timing such as socioeconomic conditions, psychosocial factors, exercise, nutritional status, chronic diseases, migration and birth weight. Using distribution percentiles of pubertal stages according to age, the relation between pubertal timing and factors affecting puberty was investigated. There was no significant association between exercise, birth weight, migration, chronic disease, and socioeconomic status and age of puberty onset. Menarcheal age of overweight and obese girls was significantly lower than that of girls with normal weight. In-family stress was the cause of early puberty in girls and of delayed puberty in boys.

  4. Factors affecting the periapical healing process of endodontically treated teeth.

    PubMed

    Holland, Roberto; Gomes, João Eduardo; Cintra, Luciano Tavares Angelo; Queiroz, Índia Olinta de Azevedo; Estrela, Carlos

    2017-01-01

    Tissue repair is an essential process that reestablishes tissue integrity and regular function. Nevertheless, different therapeutic factors and clinical conditions may interfere in this process of periapical healing. This review aims to discuss the important therapeutic factors associated with the clinical protocol used during root canal treatment and to highlight the systemic conditions associated with the periapical healing process of endodontically treated teeth. The antibacterial strategies indicated in the conventional treatment of an inflamed and infected pulp and the modulation of the host's immune response may assist in tissue repair, if wound healing has been hindered by infection. Systemic conditions, such as diabetes mellitus and hypertension, can also inhibit wound healing. The success of root canal treatment is affected by the correct choice of clinical protocol. These factors are dependent on the sanitization process (instrumentation, irrigant solution, irrigating strategies, and intracanal dressing), the apical limit of the root canal preparation and obturation, and the quality of the sealer. The challenges affecting the healing process of endodontically treated teeth include control of the inflammation of pulp or infectious processes and simultaneous neutralization of unpredictable provocations to the periapical tissue. Along with these factors, one must understand the local and general clinical conditions (systemic health of the patient) that affect the outcome of root canal treatment prediction.

  5. Nurse aide decision making in nursing homes: factors affecting empowerment.

    PubMed

    Chaudhuri, Tanni; Yeatts, Dale E; Cready, Cynthia M

    2013-09-01

    To evaluate factors affecting structural empowerment among nurse aides in nursing homes. Structural empowerment can be defined as the actual rather than perceived ability to make autonomous decisions within an organisation. Given the paucity of research on the subject, this study helps to close the gap by identifying factors that affect nurse aide empowerment, that is, decision-making among nurse aides. The data for the study come from self-administered questionnaires distributed to direct-care workers (nurse aides) in 11 nursing homes in a southern state in the USA. Ordinary least square regression models were estimated to analyse the effects of demographic predictors, personal factors (competency, emotional exhaustion and positive attitude) and structural characteristics (coworker and supervisor support, information availability and shared governance) on nurse aide decision-making. Findings suggest race among demographic predictors, emotional exhaustion among personal characteristics, and supervisor support, and shared governance among structural factors, significantly affect nurse aide decision-making. It is important to explore race as one of the central determinants of structural empowerment among nurse aides. In addition, the nature and type of emotional exhaustion that propels decision-making needs to be further examined. The study shows the importance of shared governance and supervisor support for fostering nurse aide empowerment. © 2013 Blackwell Publishing Ltd.

  6. Validation of the Atmospheric Infrared Sounder (AIRS) over the Antarctic Plateau: Low Radiance, Low Humidity, and Thin Clouds

    NASA Technical Reports Server (NTRS)

    Tobin, David C.

    2005-01-01

    The main goal of the project has been to use specialized measurements collected at the Antarctic Plateau to provide validation of the Atmospheric InfraRed Sounder (AIRS) spectral radiances and some AIRS Level 2 products. As proposed, efforts conducted at the University of Wisconsin are focused on providing technical information, data, and software in support of the validation studies.

  7. Nutritional Factors Affecting Adult Neurogenesis and Cognitive Function

    USDA-ARS?s Scientific Manuscript database

    Adult neurogenesis, a complex process by which stem cells in the hippocampal brain region differentiate and proliferate into new neurons and other resident brain cells, is known to be affected by many intrinsic and extrinsic factors, including diet. Neurogenesis plays a critical role in neural plas...

  8. Studies of the net surface radiative flux from satellite radiances during FIFE

    NASA Technical Reports Server (NTRS)

    Frouin, Robert

    1993-01-01

    Studies of the net surface radiative flux from satellite radiances during First ISLSCP Field Experiment (FIFE) are presented. Topics covered include: radiative transfer model validation; calibration of VISSR and AVHRR solar channels; development and refinement of algorithms to estimate downward solar and terrestrial irradiances at the surface, including photosynthetically available radiation (PAR) and surface albedo; verification of these algorithms using in situ measurements; production of maps of shortwave irradiance, surface albedo, and related products; analysis of the temporal variability of shortwave irradiance over the FIFE site; development of a spectroscopy technique to estimate atmospheric total water vapor amount; and study of optimum linear combinations of visible and near-infrared reflectances for estimating the fraction of PAR absorbed by plants.

  9. The key factors affecting students' individual interest in school science lessons

    NASA Astrophysics Data System (ADS)

    Cheung, Derek

    2018-01-01

    Individual interest in school science lessons can be defined as a relatively stable and enduring personal emotion comprising affective and behavioural reactions to events in the regular science lessons at school. Little research has compared the importance of different factors affecting students' individual interest in school science lessons. The present study aimed to address this gap, using a mixed methods design. Qualitative interview data were collected from 60 Hong Kong junior secondary school students, who were asked to describe the nature of their interest in science lessons and the factors to which they attribute this. Teacher interviews, parent interviews, and classroom observations were conducted to triangulate student interview data. Five factors affecting students' individual interest in school science lessons were identified: situational influences in science lessons, individual interest in science, science self-concept, grade level, and gender. Quantitative data were then collected from 591 students using a questionnaire. Structural equation modelling was applied to test a hypothesised model, which provided an acceptable fit to the student data. The strongest factor affecting students' individual interest in school science lessons was science self-concept, followed by individual interest in science and situational influences in science lessons. Grade level and gender were found to be nonsignificant factors. These findings suggest that teachers should pay special attention to the association between academic self-concept and interest if they want to motivate students to learn science at school.

  10. Simulating the Daylight Performance of Complex Fenestration Systems Using Bidirectional Scattering Distribution Functions within Radiance

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Ward, Gregory; Mistrick, Ph.D., Richard; Lee, Eleanor

    2011-01-21

    We describe two methods which rely on bidirectional scattering distribution functions (BSDFs) to model the daylighting performance of complex fenestration systems (CFS), enabling greater flexibility and accuracy in evaluating arbitrary assemblies of glazing, shading, and other optically-complex coplanar window systems. Two tools within Radiance enable a) efficient annual performance evaluations of CFS, and b) accurate renderings of CFS despite the loss of spatial resolution associated with low-resolution BSDF datasets for inhomogeneous systems. Validation, accuracy, and limitations of the methods are discussed.

  11. 75 FR 80114 - Agency Information Collection (Obligation To Report Factors Affecting Entitlement) Activity Under...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-12-21

    ... (Obligation To Report Factors Affecting Entitlement) Activity Under OMB Review AGENCY: Veterans Benefits... Report Factors Affecting Entitlement (38 CFR 3.204(a)(1), 38 CFR 3.256(a) and 38 CFR 3.277(b)). OMB... benefits must report changes in their entitlement factors. Individual factors such as income, marital...

  12. Factors Affecting Students' Grades in Principles of Economics

    ERIC Educational Resources Information Center

    Kara, Orhan; Bagheri, Fathollah; Tolin, Thomas

    2009-01-01

    Factors affecting students' grades in principles of microeconomics and macroeconomics students are analyzed from the data collected in two public universities. Results indicate that gender, number of hours worked, SAT scores, number of missed classes, recommending the course to a friend, instructors, being a junior, number of economics courses…

  13. Systematic review of factors affecting pharmaceutical expenditures.

    PubMed

    Mousnad, Mohamed Awad; Shafie, Asrul Akmal; Ibrahim, Mohamed Izham

    2014-06-01

    To systematically identify the main factors contributing to the increase in pharmaceutical expenditures. A systematic search of published studies was conducted utilising major widely used electronic databases using the search terms 'factors,' 'financing,' 'pharmaceutical,' and 'expenditures.' To be included, the studies needed to: (1) measure at least one of the following outcomes: total growth in pharmaceutical expenditures, price growth or quantity growth; (2) mention a clear method for analysing the impact of factors affecting the increases in drug expenditures; (3) be written in English. Nonprimary articles that were published only as an abstract, a review, a commentary or a letter were excluded. From a total of 2039 studies, only 25 were included in the full review. The main determinant categories that were identified in the review were factors related to price, utilisation, therapeutic choice, demand and health care system. The major cost drivers were found to be changes in drug quantities and therapies as well as new drugs. It is important for policymakers to understand pharmaceutical spending trends and the factors that influence them in order to formulate effective cost containment strategies and design optimum drug policy. Copyright © 2014 Elsevier Ireland Ltd. All rights reserved.

  14. Using the multiangle polarimetric measuring capabilities of the 2010 NASA/Glory mission to separate atmospheric scattering contributions from radiances emerging from open oceans in the visible part of the spectrum

    NASA Astrophysics Data System (ADS)

    Chowdhary, J.; Cairns, B.; Mishchenko, M. I.; Carlson, B. E.

    2009-12-01

    Answering the question of what measurements represent benchmarks for the state of the climate of the Earth is one that is of crucial importance for determining what remote sensing measurements will be made in the future. The Aerosol Polarimetry Sensor (APS), scheduled for launch into the A-train in 2010 onboard the NASA/Glory Mission, will provide multiangle, multispectral polarized reflectance measurements of sunlight reflected by the Earth’s atmosphere-surface system. The accuracy of aerosol retrievals from these measurements has already been demonstrated in field campaigns with data obtained by an airborne version of the APS, namely, the Research Scanning Polarimeter (RSP). There are several factors contributing to the success of these retrievals. One of these is the better tools available for the analyses of polarized reflectance than for the analyses of total reflectance which allows the atmospheric scattering contributions to be separated from reflection by the lower boundary whether the underlying surface be land, an ocean or lake, or even clouds. The one we focus on here is the capability to use polarization to separate atmospheric scattering from water- leaving radiances. We review a radiative transfer model for underwater light scattering that computes these radiances, and apply the results to analyses of data obtained by the RSP over the open ocean during the MILAGRO field campaign. We demonstrate that the sensitivity of remotely sensed polarized reflectances to variations in the ocean color is much smaller than that of total reflectances. Uncertainties in underwater light scattering properties that are difficult to quantify, such as absorption by colored dissolved organic materials, have a negligible effect on the polarized reflectances whereas the reflectances are substantially affected in the blue/UV part of the spectrum. This of course means that, while the polarized reflectances can be used to characterize the atmosphere, valuable information can

  15. Key factors affecting dying children and their families.

    PubMed

    Hinds, Pamela S; Schum, Lisa; Baker, Justin N; Wolfe, Joanne

    2005-01-01

    The death of a child alters the life and health of others immediately and for the rest of their lives. How a child dies influences parents' abilities to continue their role functions as well as siblings' abilities to make and maintain friendships, and may be the basis for health care providers' decisions to exit direct care roles. Thus, facilitating a "good death"-an obvious care priority for all involved with the dying child-ought also to be a priority for the health of bereaved families and affected health care providers. Making this a care priority is complicated by a serious lack of data, as details of the last hours or weeks of a dying child or adolescent's life are largely unknown. The purpose of this paper is to identify key factors that affect the course of dying children and adolescents and that of their bereaved survivors, and to link those key factors to needed research that could produce clinically relevant findings to improve the care of these patients. Key factors described here include suffering (physical, psychological, and spiritual), communication, decision making, prognostic ambiguities, ability of the seriously ill child to give assent to research participation, and educational preparation of health care providers to give competent end-of-life care.

  16. Genetic factors affecting dental caries risk.

    PubMed

    Opal, S; Garg, S; Jain, J; Walia, I

    2015-03-01

    This article reviews the literature on genetic aspects of dental caries and provides a framework for the rapidly changing disease model of caries. The scope is genetic aspects of various dental factors affecting dental caries. The PubMed database was searched for articles with keywords 'caries', 'genetics', 'taste', 'diet' and 'twins'. This was followed by extensive handsearching using reference lists from relevant articles. The post-genomic era will present many opportunities for improvement in oral health care but will also present a multitude of challenges. We can conclude from the literature that genes have a role to play in dental caries; however, both environmental and genetic factors have been implicated in the aetiology of caries. Additional studies will have to be conducted to replicate the findings in a different population. Identification of genetic risk factors will help screen and identify susceptible patients to better understand the contribution of genes in caries aetiopathogenesis. Information derived from these diverse studies will provide new tools to target individuals and/or populations for a more efficient and effective implementation of newer preventive measures and diagnostic and novel therapeutic approaches in the management of this disease. © 2015 Australian Dental Association.

  17. Factors affecting sustainability of rural water schemes in Swaziland

    NASA Astrophysics Data System (ADS)

    Peter, Graciana; Nkambule, Sizwe E.

    The Millennium Development Goal (MDG) target to reduce the proportion of people without sustainable access to safe drinking water by the year 2015 has been met as of 2010, but huge disparities exist. Some regions, particularly Sub-Saharan Africa are lagging behind it is also in this region where up to 30% of the rural schemes are not functional at any given time. There is need for more studies on factors affecting sustainability and necessary measures which when implemented will improve the sustainability of rural water schemes. The main objective of this study was to assess the main factors affecting the sustainability of rural water schemes in Swaziland using a Multi-Criteria Analysis Approach. The main factors considered were: financial, social, technical, environmental and institutional. The study was done in Lubombo region. Fifteen functional water schemes in 11 communities were studied. Data was collected using questionnaires, checklist and focused group discussion guide. A total of 174 heads of households were interviewed. Statistical Package for Social Sciences (SPSS) was used to analyse the data and to calculate sustainability scores for water schemes. SPSS was also used to classify sustainability scores according to sustainability categories: sustainable, partially sustainable and non-sustainable. The averages of the ratings for the different sub-factors studied and the results on the sustainability scores for the sustainable, partially sustainable and non-sustainable schemes were then computed and compared to establish the main factors influencing sustainability of the water schemes. The results indicated technical and social factors as most critical while financial and institutional, although important, played a lesser role. Factors which contributed to the sustainability of water schemes were: functionality; design flow; water fetching time; ability to meet additional demand; use by population; equity; participation in decision making on operation and

  18. Factors Affecting Online Groupwork Interest: A Multilevel Analysis

    ERIC Educational Resources Information Center

    Du, Jianxia; Xu, Jianzhong; Fan, Xitao

    2013-01-01

    The purpose of the present study is to examine the personal and contextual factors that may affect students' online groupwork interest. Using the data obtained from graduate students in an online course, both student- and group-level predictors for online groupwork interest were analyzed within the framework of hierarchical linear modeling…

  19. Factors Affecting the Technology Readiness of Health Professionals

    ERIC Educational Resources Information Center

    Myers, Stephanie E.

    2010-01-01

    Federal government policies are promoting diffusion of technologies into the healthcare system. If health professionals reject the new technologies planned for the healthcare system, it could result in costly failures, delays, and workforce problems. There is a lack of knowledge about factors that affect technology readiness (TR), defined as the…

  20. Factors affecting receipt of chemotherapy in women with breast cancer

    PubMed Central

    Morimoto, Libby; Coalson, Jenna; Mowat, Fionna; O’Malley, Cynthia

    2010-01-01

    Aims: To review literature describing factors associated with receipt of chemotherapy for breast cancer, to better understand what factors are most relevant to women’s health and whether health disparities are apparent, and to assess how these factors might affect observational studies and outcomes research. Patterns of care for metastatic breast cancer, for which no standard-of-care exists, were of particular interest. Methods: Relevant studies written in English, Italian, French, or Spanish, published in 2000 or later, were identified through MEDLINE and reviewed. Review articles and clinical trials were excluded; all observational studies and surveys were considered. Articles were reviewed for any discussion of patient characteristics, hospital/physician/insurance characteristics, psychosocial characteristics, and clinical characteristics affecting receipt of chemotherapy by breast cancer patients. Results: In general, factors associated with increased likelihood of receiving chemotherapy included younger age, being Caucasian, having good general health and few co-morbidities, having more severe clinical disease, having responded well to previous treatment, and having breast cancer that is estrogen- or progesterone-receptor-negative. Many of the clinical factors found to increase the likelihood of receiving chemotherapy were consistent with current oncology guidelines. Of the relevant 19 studies identified, only six (32%) reported data specific to metastatic cancer; most studies aggregated women with stage I–IV for purposes of analysis. Conclusion: Studies of patterns of care in breast cancer treatment can help identify challenges in health care provided to particular subgroups of women and can aid researchers in designing studies that account for such factors in clinical and outcomes research. Although scarce, studies evaluating only women with metastatic breast cancer indicate that factors affecting decisions related to receipt of chemotherapy are similar

  1. The role of ensemble-based statistics in variational assimilation of cloud-affected observations from infrared imagers

    NASA Astrophysics Data System (ADS)

    Hacker, Joshua; Vandenberghe, Francois; Jung, Byoung-Jo; Snyder, Chris

    2017-04-01

    Effective assimilation of cloud-affected radiance observations from space-borne imagers, with the aim of improving cloud analysis and forecasting, has proven to be difficult. Large observation biases, nonlinear observation operators, and non-Gaussian innovation statistics present many challenges. Ensemble-variational data assimilation (EnVar) systems offer the benefits of flow-dependent background error statistics from an ensemble, and the ability of variational minimization to handle nonlinearity. The specific benefits of ensemble statistics, relative to static background errors more commonly used in variational systems, have not been quantified for the problem of assimilating cloudy radiances. A simple experiment framework is constructed with a regional NWP model and operational variational data assimilation system, to provide the basis understanding the importance of ensemble statistics in cloudy radiance assimilation. Restricting the observations to those corresponding to clouds in the background forecast leads to innovations that are more Gaussian. The number of large innovations is reduced compared to the more general case of all observations, but not eliminated. The Huber norm is investigated to handle the fat tails of the distributions, and allow more observations to be assimilated without the need for strict background checks that eliminate them. Comparing assimilation using only ensemble background error statistics with assimilation using only static background error statistics elucidates the importance of the ensemble statistics. Although the cost functions in both experiments converge to similar values after sufficient outer-loop iterations, the resulting cloud water, ice, and snow content are greater in the ensemble-based analysis. The subsequent forecasts from the ensemble-based analysis also retain more condensed water species, indicating that the local environment is more supportive of clouds. In this presentation we provide details that explain the

  2. Factors affecting the periapical healing process of endodontically treated teeth

    PubMed Central

    Holland, Roberto; Gomes, João Eduardo; Cintra, Luciano Tavares Angelo; Queiroz, Índia Olinta de Azevedo; Estrela, Carlos

    2017-01-01

    Abstract Tissue repair is an essential process that reestablishes tissue integrity and regular function. Nevertheless, different therapeutic factors and clinical conditions may interfere in this process of periapical healing. This review aims to discuss the important therapeutic factors associated with the clinical protocol used during root canal treatment and to highlight the systemic conditions associated with the periapical healing process of endodontically treated teeth. The antibacterial strategies indicated in the conventional treatment of an inflamed and infected pulp and the modulation of the host's immune response may assist in tissue repair, if wound healing has been hindered by infection. Systemic conditions, such as diabetes mellitus and hypertension, can also inhibit wound healing. The success of root canal treatment is affected by the correct choice of clinical protocol. These factors are dependent on the sanitization process (instrumentation, irrigant solution, irrigating strategies, and intracanal dressing), the apical limit of the root canal preparation and obturation, and the quality of the sealer. The challenges affecting the healing process of endodontically treated teeth include control of the inflammation of pulp or infectious processes and simultaneous neutralization of unpredictable provocations to the periapical tissue. Along with these factors, one must understand the local and general clinical conditions (systemic health of the patient) that affect the outcome of root canal treatment prediction. PMID:29069143

  3. Simultaneous effects of environmental factors on motile Aeromonas dynamics in an urban effluent and in the natural seawater.

    PubMed

    Maalej, Sami; Mahjoubi, Amira; Elazri, Chafai; Dukan, Sam

    2003-07-01

    Seasonal dynamics of motile Aeromonas in a treated urban effluent and in natural seawater along the Sfax coast (Mediterranean sea, Tunisia) were measured over a year concurrently with seven environmental factors, and compared with those of faecal coliforms. Counts for Aeromonas from a standard plate count method, ranged from 1.48 x 10(5)CFU.100 ml(-1) to 2.2 x 10(8)CFU.100 ml(-1) in the effluent and from 7.9 x 10(3)CFU.100 ml(-1) to undetectable level in the surface marine waters. Contrary to faecal coliforms, the Aeromonas dynamics exhibited a seasonal distribution in seawater which was inverse of the seasonal distribution in the sewage: From the end of November 1998 to April 1999 (cold period), Aeromonas counts increased in the treated effluent, while it decreased very rapidly in seawater. From May to October (warm period), Aeromonas abundance decreased in the effluent but showed an increasing fluctuating trend in the marine waters with a maximum in late summer/early autumn when the temperatures were around 22-23 degrees C. Multiple correlation and regression analyses suggest, by the coefficient of determination (R(2)), that 42% of variance in Aeromonas number changes in the treated effluent, may be explained by only turbidity, radiation and Aeromonas density in the previous sample, while 37% of variance in marine ecosystem were explained by radiance and conductivity. Furthermore, the t statistics and their p values and the coefficient of partial determination (r(2)) indicated that radiance contributed the most (r(2)=0.3184, t=-3.2, p=0.0041) to the dynamics of motile Aeromonas in seawater, when combined with conductivity. The models relevant for changes in faecal coliforms abundance incorporated turbidity, radiance in the effluent and conductivity, pH, radiance, turbidity in coastal marine environment. These models explain 66% and 73% of the observed cell number fluctuation, with turbidity (r(2)=0.529, t=5.08, p=0.0001) and conductivity (r(2)=0.5407, t=4.97, p=0

  4. Factors affecting outcome in ocular myasthenia gravis.

    PubMed

    Mazzoli, Marco; Ariatti, Alessandra; Valzania, Franco; Kaleci, Shaniko; Tondelli, Manuela; Nichelli, Paolo F; Galassi, Giuliana

    2018-01-01

    50%-60% of patients with ocular myasthenia gravis (OMG) progress to generalized myasthenia gravis (GMG) within two years. The aim of our study was to explore factors affecting prognosis of OMG and to test the predictive role of several independent clinical variables. We reviewed a cohort of 168 Caucasian patients followed from September 2000 to January 2016. Several independent variables were considered as prognostic factors: gender, age of onset, results on electrophysiological tests, presence and level of antibodies against acetylcholine receptors (AChR Abs), treatments, thymic abnormalities. The primary outcome was the progression to GMG and/or the presence of bulbar symptoms. Secondary outcomes were either achievement of sustained minimal manifestation status or worsening in ocular quantitative MG subscore (O-QMGS) or worsening in total QMG score (T-QMGS), assessed by Myasthenia Gravis Foundation of America (MGFA) quantitative scores. Changes in mental and physical subscores of health-related quality of life (HRQoL) were assessed with SF-36 questionnaire. Variance analysis was used to interpret the differences between AChR Ab titers at different times of follow up among the generalized and non-generalized patients. Conversion to GMG occurred in 18.4% of patients; it was significantly associated with sex, later onset of disease and anti-AChR Ab positivity. Antibody titer above the mean value of 25.8 pmol/mL showed no significant effect on generalization. Sex and late onset of disease significantly affected T-QMGS worsening. None of the other independent variables significantly affected O-QMGS and HRQoL. Sex, later onset and anti-AChR Ab positivity were significantly associated with clinical worsening.

  5. Factors affecting sexual function in menopause: A review article.

    PubMed

    Nazarpour, Soheila; Simbar, Masoumeh; Tehrani, Fahimeh Ramezani

    2016-08-01

    This study aimed to systematically review the articles on factors affecting sexual function during menopause. Searching articles indexed in Pubmed, Science Direct, Iranmedex, EMBASE, Scopus, and Scientific Information Database databases, a total number of 42 studies published between 2003 and 2013 were selected. Age, estrogen deficiency, type of menopause, chronic medical problems, partner's sex problems, severity of menopause symptoms, dystocia history, and health status were the physical factors influencing sexual function of menopausal women. There were conflicting results regarding the amount of androgens, hormonal therapy, exercise/physical activity, and obstetric history. In the mental-emotional area, all studies confirmed the impact of depression and anxiety. Social factors, including smoking, alcohol consumption, the quality of relationship with husband, partner's loyalty, sexual knowledge, access to health care, a history of divorce or the death of a husband, living apart from a spouse, and a negative understanding of women's health were found to affect sexual function; however, there were conflicting results regarding the effects of education, occupation, socioeconomic status, marital duration, and frequency of sexual intercourse. Copyright © 2016. Published by Elsevier B.V.

  6. Science Enabling Applications of Gridded Radiances and Products

    NASA Astrophysics Data System (ADS)

    Goldberg, M.; Wolf, W.; Zhou, L.

    2005-12-01

    New generations of hyperspectral sounders and imagers are not only providing vastly improved information to monitor, assess and predict the Earth's environment, they also provide tremendous volumes of data to manage. Key management challenges must include data processing, distribution, archive and utilization. At the NOAA/NESDIS Office of Research and Applications, we have started to address the challenge of utilizing high volume satellite by thinning observations and developing gridded datasets from the observations made from the NASA AIRS, AMSU and MODIS instrument. We have developed techniques for intelligent thinning of AIRS data for numerical weather prediction, by selecting the clearest AIRS 14 km field of view within a 3 x 3 array. The selection uses high spatial resolution 1 km MODIS data which are spatially convolved to the AIRS field of view. The MODIS cloud masks and AIRS cloud tests are used to select the clearest. During the real-time processing the data are thinned and gridded to support monitoring, validation and scientific studies. Products from AIRS, which includes profiles of temperature, water vapor and ozone and cloud-corrected infrared radiances for more than 2000 channels, are derived from a single AIRS/AMSU field of regard, which is a 3 x 3 array of AIRS footprints (each with a 14 km spatial resolution) collocated with a single AMSU footprint (42 km). One of our key gridded dataset is a daily 3 x 3 latitude/longitude projection which contains the nearest AIRS/AMSU field of regard with respect to the center of the 3 x 3 lat/lon grid. This particular gridded dataset is 1/40 the size of the full resolution data. This gridded dataset is the type of product request that can be used to support algorithm validation and improvements. It also provides for a very economical approach for reprocessing, testing and improving algorithms for climate studies without having to reprocess the full resolution data stored at the DAAC. For example, on a single CPU

  7. Analysis on factors affecting consumers decision on purchasing simple-type houses

    NASA Astrophysics Data System (ADS)

    Rumintang, A.; Sholichin, I.

    2018-01-01

    In line with the increase of the population and the need of comfortable houses, as affected by modernization era, the house demand is getting higher. Hence, conducting a research on consumers need and want in buying a house should be seriously attempted to succeed marketing activity. Using an analysis consumers’ behavior, the researcher will know few affecting factors related to consumers’ satisfaction in buying a house. Among other, the factors in question include: house price, house condition, facilities, location and accessability. The sample of this research was drawn from the residents of Graha Asri Housing, Taman Bulang Permai, and Sukodono Permai. Based on the analysis and discussion, some conclusions are made as follow: the factors and variables affecting the consumers’ decision on each choice of house is different and also the same variables on three sources of data include housing atmosphere, cleaning service, ease of access to shopping center, health clinics or hospitals, tourism spot, schools, and the bus station.

  8. 14 CFR Appendix B to Part 1215 - Factors Affecting Standard Charges

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... DATA RELAY SATELLITE SYSTEM (TDRSS) Pt. 1215, App. B Appendix B to Part 1215—Factors Affecting Standard Charges Charges for services shall be determined by multiplying the factors below by the base rates for...

  9. Other Factors That Affect Heart Disease: Birth Control Pills

    MedlinePlus

    ... Heart Handbook for Women Other Factors That Affect Heart Disease Birth Control Pills Studies show that women who ... t had any more complications because of my heart disease." — Diane Pay attention to diabetes. Levels of glucose, ...

  10. Reappraising factors affecting mourning dove perch coos

    USGS Publications Warehouse

    Sayre, M.W.; Atkinson, R.D.; Baskett, T.S.; Haas, G.H.

    1978-01-01

    Results confirmed pairing as the primary factor influencing perch-cooing rates of wild mourning doves (Zenaida macroura). Marked unmated males cooed at substantially higher rates (6.2x) than mated males, had greater probability of cooing (2.3x) during 3-minute periods, and continued cooing longer each morning than mated males. Population density was not a major factor affecting cooing. Unmated males cooed more frequently in the presence of other cooing doves (P < 0.05) than when alone, but the number of additional doves above 1 was unimportant. Cooing rates of both mated and unmated males on areas with dissimilar dove densities were not significantly different. Within limits of standard call-count procedure, weather exerted no detectable influence on cooing.

  11. Organisational Factors Affecting Policy and Programme Decision Making in a Public Health Policy Environment

    ERIC Educational Resources Information Center

    Zardo, Pauline; Collie, Alex; Livingstone, Charles

    2015-01-01

    Organisational factors can affect the success of interventions aimed at increasing research use. Research is needed to identify organisational factors affecting research use in specific public health policy contexts. Qualitative interviews with decision makers from a specific public health context identified a range of organisational factors that…

  12. Factors affecting dental service quality.

    PubMed

    Bahadori, Mohammadkarim; Raadabadi, Mehdi; Ravangard, Ramin; Baldacchino, Donia

    2015-01-01

    Measuring dental clinic service quality is the first and most important factor in improving care. The quality provided plays an important role in patient satisfaction. The purpose of this paper is to identify factors affecting dental service quality from the patients' viewpoint. This cross-sectional, descriptive-analytical study was conducted in a dental clinic in Tehran between January and June 2014. A sample of 385 patients was selected from two work shifts using stratified sampling proportional to size and simple random sampling methods. The data were collected, a self-administered questionnaire designed for the purpose of the study, based on the Parasuraman and Zeithaml's model of service quality which consisted of two parts: the patients' demographic characteristics and a 30-item questionnaire to measure the five dimensions of the service quality. The collected data were analysed using SPSS 21.0 and Amos 18.0 through some descriptive statistics such as mean, standard deviation, as well as analytical methods, including confirmatory factor. Results showed that the correlation coefficients for all dimensions were higher than 0.5. In this model, assurance (regression weight=0.99) and tangibility (regression weight=0.86) had, respectively, the highest and lowest effects on dental service quality. The Parasuraman and Zeithaml's model is suitable to measure quality in dental services. The variables related to dental services quality have been made according to the model. This is a pioneering study that uses Parasuraman and Zeithaml's model and CFA in a dental setting. This study provides useful insights and guidance for dental service quality assurance.

  13. Exploring Factors that Affect Purchase Intention of Athletic Team Merchandise

    ERIC Educational Resources Information Center

    Lee, Donghun; Trail, Galen T.; Lee, Cindy; Schoenstedt, Linda J.

    2013-01-01

    The purpose of this study was to test a structural model to determine which psychosocial constructs affected the purchase intention of athletic team merchandise (ATM). Results from the analyses indicated that the twelve-factor ATM model fit the data from collegiate athletic events well, explaining the various impact factors that lead to purchase…

  14. Spectral radiance estimates of leaf area and leaf phytomass of small grains and native vegetation

    NASA Technical Reports Server (NTRS)

    Aase, J. K.; Brown, B. S.; Millard, J. P.

    1986-01-01

    Similarities and/or dissimilarities in radiance characteristics were studied among barley (Hordeum vulgare L.), oats (Avena fatua L.), spring and winter wheat (Triticum aestivum L.), and short-grass prairie vegetation. The site was a Williams loam soil (fine-loamy mixed, Typic Argiborolls) near Sidney, Montana. Radiances were measured with a truck-mounted radiometer. The radiometer was equipped with four wavelength bands: 0.45 to 0.52, 0.52 to 0.60, 0.63 to 0.69, and 0.76 to 0.90 micron. Airborne scanner measurements were made at an altitude of 600 m four times during the season under clear sky conditions. The airborne scanner was equipped with the same four bands as the truck-mounted radiometer plus the following: 1.00 to 1.30, 1.55 to 1.75, 2.08 to 2.35, and 10.4 to 12.5 microns. Comparisons using individual wave bands, the near IR/red, (0.76 to 0.90 micron)/(0.63 to 0.69 micron) ratio and the normalized difference vegetation index, ND = (IR - red)/(IR + red), showed that only during limited times during the growing season were some of the small grains distinguishable from one another and from native rangeland vegetation. There was a common relation for all small grains between leaf area index and green leaf phytomass and between leaf area index or green leaf phytomass and the IR/red ratio.

  15. Estimating snow depth of alpine snowpack via airborne multifrequency passive microwave radiance observations: Colorado, USA

    NASA Astrophysics Data System (ADS)

    Kim, R. S.; Durand, M. T.; Li, D.; Baldo, E.; Margulis, S. A.; Dumont, M.; Morin, S.

    2017-12-01

    This paper presents a newly-proposed snow depth retrieval approach for mountainous deep snow using airborne multifrequency passive microwave (PM) radiance observation. In contrast to previous snow depth estimations using satellite PM radiance assimilation, the newly-proposed method utilized single flight observation and deployed the snow hydrologic models. This method is promising since the satellite-based retrieval methods have difficulties to estimate snow depth due to their coarse resolution and computational effort. Indeed, this approach consists of particle filter using combinations of multiple PM frequencies and multi-layer snow physical model (i.e., Crocus) to resolve melt-refreeze crusts. The method was performed over NASA Cold Land Processes Experiment (CLPX) area in Colorado during 2002 and 2003. Results showed that there was a significant improvement over the prior snow depth estimates and the capability to reduce the prior snow depth biases. When applying our snow depth retrieval algorithm using a combination of four PM frequencies (10.7,18.7, 37.0 and 89.0 GHz), the RMSE values were reduced by 48 % at the snow depth transects sites where forest density was less than 5% despite deep snow conditions. This method displayed a sensitivity to different combinations of frequencies, model stratigraphy (i.e. different number of layering scheme for snow physical model) and estimation methods (particle filter and Kalman filter). The prior RMSE values at the forest-covered areas were reduced by 37 - 42 % even in the presence of forest cover.

  16. Far-infrared Spectral Radiance Observations and Modeling of Arctic Cirrus: Preliminary Results From RHUBC

    NASA Astrophysics Data System (ADS)

    Humpage, Neil; Green, Paul D.; Harries, John E.

    2009-03-01

    Recent studies have highlighted the important contribution of the far-infrared (electromagnetic radiation with wavelengths greater than 12 μm) to the Earth's radiative energy budget. In a cloud-free atmosphere, a significant fraction of the Earth's cooling to space from the mid- and upper troposphere takes place via the water vapor pure rotational band between 17 and 33 μm. Cirrus clouds also play an important role in the Earth's outgoing longwave radiation. The effect of cirrus on far-infrared radiation is of particular interest, since the refractive index of ice depends strongly on wavelength in this spectral region. The scattering properties of ice crystals are directly related to the refractive index, so consequently the spectral signature of cirrus measured in the FIR is sensitive to the cloud microphysical properties [1, 2]. By examining radiances measured at wavelengths between the strong water vapor absorption lines in the FIR, the understanding of the relationship between cirrus microphysics and the radiative transfer of thermal energy through cirrus may be improved. Until recently, very few observations of FIR spectral radiances had been made. The Tropospheric Airborne Fourier Transform Spectrometer (TAFTS) was developed by Imperial College to address this lack of observational data. TAFTS observes both zenith and nadir radiances at 0.1 cm-1 resolution, between 80 and 600 cm-1. During February and March 2007, TAFTS was involved in RHUBC (the Radiative Heating in Under-explored Bands Campaign), an ARM funded field campaign based at the ACRF-North Slope of Alaska site near Barrow, situated at 71° latitude. Infrared zenith spectral observations were taken by both TAFTS and the AERI-ER (spectral range 400-3300 cm-1) from the ground during both cloud-free and cirrus conditions. A wide range of other instrumentation was also available at the site, including a micropulse lidar, 35 GHz radar and the University of Colorado/NOAA Ground-based Scanning Radiometer

  17. SIMBIOS Normalized Water-Leaving Radiance Calibration and Validation: Sensor Response, Atmospheric Corrections, Stray Light and Sun Glint. Chapter 14

    NASA Technical Reports Server (NTRS)

    Mueller, James L.

    2001-01-01

    This Sensor Intercomparison and Merger for Biological and Interdisciplinary Oceanic Studies (SIMBIOS) contract supports acquisition of match up radiometric and bio-optical data for validation of Sea-Viewing Wide Field-of-view Sensor (SeaWiFS) and other ocean color satellites, and evaluation of uncertainty budgets and protocols for in situ measurements of normalized water leaving radiances.

  18. 29 CFR 784.118 - The exemption is intended for work affected by natural factors.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 29 Labor 3 2011-07-01 2011-07-01 false The exemption is intended for work affected by natural...(a)(5) Exemption § 784.118 The exemption is intended for work affected by natural factors. As... that are controlled or materially affected by natural factors or elements, such as the vicissitudes of...

  19. 29 CFR 784.118 - The exemption is intended for work affected by natural factors.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 29 Labor 3 2010-07-01 2010-07-01 false The exemption is intended for work affected by natural...(a)(5) Exemption § 784.118 The exemption is intended for work affected by natural factors. As... that are controlled or materially affected by natural factors or elements, such as the vicissitudes of...

  20. Formal Classroom Observations: Factors That Affect Their Success

    ERIC Educational Resources Information Center

    Zaidi, Zeba

    2017-01-01

    Formal class room observation is a very delicate topic in any educational institution. It involves a series of emotions and sentiments that come with the package. In this paper, the researcher will attempt to analyze the factors that affect the process in a relatively significant manner and thereby contribute greatly to the success or failure of…

  1. Factors affecting patient compliance with compressive brace therapy for pectus carinatum.

    PubMed

    Kang, Du-Young; Jung, Junho; Chung, Sangho; Cho, Jinkyung; Lee, Sungsoo

    2014-12-01

    The aim of this study was to identify factors affecting patient compliance with brace therapy for pectus carinatum. Eighty-six pectus carinatum patients who started brace therapy from August 2008 to November 2011 were included in this study. Patients were divided into two groups: patients who wore the brace for ≥6 months (compliance group) or patients who wore the brace for <6 months (non-compliance group). Factors affecting patient compliance were assessed at the last day of follow-up with a multiple-choice questionnaire. The questionnaire comprised seven items: pain at compression site, skin problems on compression area, confidence in brace treatment, shame, discomfort, initial result of bracing treatment and total number of factors affecting patient compliance. Eighty-six patients completed the survey, including seven (8.1%) female patients and 79 (91.9%) male patients, with a mean age of 12.0 years at the time of treatment (range, 3-20 years). The initial result of the compression period (P <0.001) and total number of factors affecting patient compliance (P <0.05) were significant predictors of patient compliance. An initial successful result of the compression period may increase patient compliance during treatment for pectus carinatum. Additional efforts to decrease pain, skin problems, shame and discomfort, and to give confidence may be beneficial in increasing compliance with bracing treatment. © The Author 2014. Published by Oxford University Press on behalf of the European Association for Cardio-Thoracic Surgery. All rights reserved.

  2. Factors affecting scholastic performances of adolescents.

    PubMed

    Shashidhar, Saraswati; Rao, Chandrika; Hegde, Radhakrishna

    2009-05-01

    The present study aims at recognizing the social influence, study habits and health factors affecting scholastic performances of adolescents and to compare these factors among the adolescents between two categories of school. A total of 1230 adolescents (13-18 yrs) were screened. Data was collected by personal interview, using the teenage screening questionnaire, Trivandrum, between May 2004 and November 2005. A total 615 students from corporation and private schools were studied. 39.76% (489) were high achievers, 13.5% (166) were low achievers with p < 0.001. In the low achievers, 12.03% were from the corporation schools and 1.46% from private schools. The incidence of poor study habits and social factors were increased in low achievers of corporation schools. On multivariate analysis, the predictor variables for poor scholastic performance were adolescent having refractory error, not having help for study at home, not doing home work regularly, not solving question bank papers and reading only before examinations. It is feasible and worthwhile to identify the determinants of scholastic performance and plan intervention strategies at each school. The results of this study highlight the importance of implementing newer strategies, focusing on strict study patterns and creating the conducive school and home environment for study, so as to achieve better scholastic performances.

  3. Factors affecting maintenance overlay ride quality : 1996 rideability status.

    DOT National Transportation Integrated Search

    1997-01-01

    In early 1996, the Virginia Transportation Research Council initiated a formal analysis of the factors affecting overlay ride quality. As part of that effort, a statewide, multi-year survey of the ride quality for both new overlays and pavement await...

  4. External factors affecting data acquisition during corneal topography examination.

    PubMed

    González-Méijome, José Manuel; Queirós, Antonio; Jorge, Jorge; Fernandes, Paulo; Cerviño, Alejandro; de Almeida, José Borges

    2007-03-01

    To analyze the factors affecting data acquisition during corneal topography examination with the Medmont E-300 videokeratoscope and to provide strategies to minimize their effects. Sixty eyes from thirty young adults were examined. A second observer registered incidences with the potential to affect data acquisition. Those factors were correlated with the difficulty of measurements as judged subjectively by the practitioner who performed the examination. Measurements of axial curvature were analyzed to evaluate the variability expressed as intrasession and intersession coefficient of variation and the standard error of the mean (SEM). The level of difficulty rated by the practitioner was in general low, with 70% of the eyes being easy or very easy to measure. For the remaining 30% of the eyes, corneal topography measurements were considered to be difficult (27%) or very difficult (3%). Of the external parameters investigated, only fixation instability (P<0.001, chi2) and the need for head repositioning (P=0.024, chi2) were associated significantly with a higher level of difficulty, as rated subjectively by the practitioner. Further analysis showed that some external factors, including those previously mentioned and others related to tear instability, affect the variability of measurements at certain corneal locations, particularly in the vertical meridian when related to tear instability and in the horizontal meridian when related to the need for head repositioning on the chin rest owing to physiognomy interferences with the keratoscope cone. Intersession SEM improved when three readings from each session were considered. The level of subjective difficulty found during videokeratoscopy examination is correlated strongly with fixation instability and the need for head reorientation in the chin rest, whereas tear-related events seem to be less relevant in the practitioner perception of test ease or difficulty. Those factors have relevance in measurement variability.

  5. Factors affecting 30-month survival in lung cancer patients.

    PubMed

    Mahesh, P A; Archana, S; Jayaraj, B S; Patil, Shekar; Chaya, S K; Shashidhar, H P; Sunitha, B S; Prabhakar, A K

    2012-10-01

    Age adjusted incidence rate of lung cancer in India ranges from 7.4 to 13.1 per 100,000 among males and 3.9 to 5.8 per 100,000 among females. The factors affecting survival in lung cancer patients in India are not fully understood. The current study was undertaken to evaluate the factors affecting survival in patients diagnosed with lung cancer attending a tertiary care cancer institute in Bangalore, Karnataka, India. Consecutive patients with primary lung cancer attending Bangalore Institute of Oncology, a tertiary care centre at Bangalore, between 2006 and 2009 were included. Demographic, clinical, radiological data were collected retrospectively from the medical records. A total of 170 consecutive subjects (128 males, 42 females) diagnosed to have lung cancer; 151 non-small cell lung cancer (NSCLC) and 19 small cell lung cancer (SCLC) were included. A higher proportion of never-smokers (54.1%) were observed, mostly presenting below the age of 60 yr. Most subjects were in stage IV and III at the time of diagnosis. More than 50 per cent of patients presented with late stage lung cancer even though the duration of symptoms is less than 2 months. The 30-month overall survival rates for smokers and never-smokers were 32 and 49 per cent, respectively. No significant differences were observed in 30 month survival based on age at presentation, gender and type of lung cancer. Cox proportional hazards model identified never-smokers and duration of symptoms less than 1 month as factors adversely affecting survival. Our results showed that lung cancer in Indians involved younger subjects and associated with poorer survival as compared to other ethnic population. Studies on large sample need to be done to evaluate risk factors in lung cancer patients.

  6. Factors affecting 30-month survival in lung cancer patients

    PubMed Central

    Mahesh, P.A.; Archana, S.; Jayaraj, B.S.; Patil, Shekar; Chaya, S.K.; Shashidhar, H.P.; Sunitha, B.S.; Prabhakar, A.K.

    2012-01-01

    Background & objectives: Age adjusted incidence rate of lung cancer in India ranges from 7.4 to 13.1 per 100,000 among males and 3.9 to 5.8 per 100,000 among females. The factors affecting survival in lung cancer patients in India are not fully understood. The current study was undertaken to evaluate the factors affecting survival in patients diagnosed with lung cancer attending a tertiary care cancer institute in Bangalore, Karnataka, India. Methods: Consecutive patients with primary lung cancer attending Bangalore Institute of Oncology, a tertiary care centre at Bangalore, between 2006 and 2009 were included. Demographic, clinical, radiological data were collected retrospectively from the medical records. Results: A total of 170 consecutive subjects (128 males, 42 females) diagnosed to have lung cancer; 151 non-small cell lung cancer (NSCLC) and 19 small cell lung cancer (SCLC) were included. A higher proportion of never-smokers (54.1%) were observed, mostly presenting below the age of 60 yr. Most subjects were in stage IV and III at the time of diagnosis. More than 50 per cent of patients presented with late stage lung cancer even though the duration of symptoms is less than 2 months. The 30-month overall survival rates for smokers and never-smokers were 32 and 49 per cent, respectively. No significant differences were observed in 30 month survival based on age at presentation, gender and type of lung cancer. Cox proportional hazards model identified never-smokers and duration of symptoms less than 1 month as factors adversely affecting survival. Interpretation & conclusions: Our results showed that lung cancer in Indians involved younger subjects and associated with poorer survival as compared to other ethnic population. Studies on large sample need to be done to evaluate risk factors in lung cancer patients. PMID:23168702

  7. Factors affecting medication-order processing time.

    PubMed

    Beaman, M A; Kotzan, J A

    1982-11-01

    The factors affecting medication-order processing time at one hospital were studied. The order processing time was determined by directly observing the time to process randomly selected new drug orders on all three work shifts during two one-week periods. An order could list more than one drug for an individual patient. The observer recorded the nature, location, and cost of the drugs ordered, as well as the time to process the order. The time and type of interruptions also were noted. The time to process a drug order was classified as six dependent variables: (1) total time, (2) work time, (3) check time, (4) waiting time I--time from arrival on the dumbwaiter until work was initiated, (5) waiting time II--time between completion of the work and initiation of checking, and (6) waiting time III--time after the check was completed until the order left on the dumbwaiter. The significant predictors of each of the six dependent variables were determined using stepwise multiple regression. The total time to process a prescription order was 58.33 +/- 48.72 minutes; the urgency status of the order was the only significant determinant of total time. Urgency status also significantly predicted the three waiting-time variables. Interruptions and the number of drugs on the order were significant determinants of work time and check time. Each telephone interruption increased the work time by 1.72 minutes. While the results of this study cannot be generalized to other institutions, pharmacy managers can use the method of determining factors that affect medication-order processing time to identify problem areas in their institutions.

  8. The solar occultation technique for remote sensing of particulates in the earth's atmosphere. I - The inversion of horizon radiances from space

    NASA Technical Reports Server (NTRS)

    Schuerman, D. W.; Giovane, F.; Greenberg, J. M.

    1976-01-01

    The aerosol scattering coefficient as a function of height can be recovered from a direct inversion of the single-scattering horizon radiance provided the sun is above the horizon and an independent measurement of extinction as a function of height is made. Aerosol detection is effected by means of spacecraft measurements of the horizon radiance made during periods of spacecraft twilight. A solar occultation technique which allows the twilight measurements to be made when the sun is still above the horizon greatly reduces the complexity of the inversion problem. The second part of the paper reports on the use of a coronograph aboard Skylab to photograph the horizon just before spacecraft twilight in order to monitor the aerosol component above the tropopause. The coronograph picture, centered on 26.5 degrees E longitude and 63.0 degrees S latitude, shows that the aerosol layer peaks at a height of 48 plus or minus 1 km.

  9. Unmixing of spectral components affecting AVIRIS imagery of Tampa Bay

    NASA Astrophysics Data System (ADS)

    Carder, Kendall L.; Lee, Z. P.; Chen, Robert F.; Davis, Curtiss O.

    1993-09-01

    According to Kirk's as well as Morel and Gentili's Monte Carlo simulations, the popular simple expression, R approximately equals 0.33 bb/a, relating subsurface irradiance reflectance (R) to the ratio of the backscattering coefficient (bb) to absorption coefficient (a), is not valid for bb/a > 0.25. This means that it may no longer be valid for values of remote-sensing reflectance (above-surface ratio of water-leaving radiance to downwelling irradiance) where Rrs4/ > 0.01. Since there has been no simple Rrs expression developed for very turbid waters, we developed one based in part on Monte Carlo simulations and empirical adjustments to an Rrs model and applied it to rather turbid coastal waters near Tampa Bay to evaluate its utility for unmixing the optical components affecting the water- leaving radiance. With the high spectral (10 nm) and spatial (20 m2) resolution of Airborne Visible-InfraRed Imaging Spectrometer (AVIRIS) data, the water depth and bottom type were deduced using the model for shallow waters. This research demonstrates the necessity of further research to improve interpretations of scenes with highly variable turbid waters, and it emphasizes the utility of high spectral-resolution data as from AVIRIS for better understanding complicated coastal environments such as the west Florida shelf.

  10. BOREAS Level-3b Landsat TM Imagery: At-sensor Radiances in BSQ Format

    NASA Technical Reports Server (NTRS)

    Hall, Forrest G. (Editor); Nickeson, Jaime; Knapp, David; Newcomer, Jeffrey A.; Cihlar, Josef

    2000-01-01

    For BOREAS, the level-3b Landsat TM data, along with the other remotely sensed images, were collected in order to provide spatially extensive information over the primary study areas. This information includes radiant energy, detailed land cover, and biophysical parameter maps such as FPAR and LAI. Although very similar in content to the level-3a Landsat TM products, the level-3b images were created to provide users with a directly usable at-sensor radiance image. Geographically, the level-3b images cover the BOREAS NSA and SSA. Temporally, the images cover the period of 22-Jun-1984 to 09-Jul-1996. The images are available in binary, image format files.

  11. Teaching the Factors Affecting Resistance Using Pencil Leads

    ERIC Educational Resources Information Center

    Küçüközer, Asuman

    2015-01-01

    The aim of this paper is to provide a way of teaching the factors that affect resistance using mechanical pencil leads and the brightness of the light given out by a light bulb connected to an electrical circuit. The resistance of a conductor is directly proportional to its length (L) and inversely proportional to its cross-sectional area (A).…

  12. Culture and affect: the factor structure of the affective style questionnaire and its relation with depression and anxiety among Japanese.

    PubMed

    Ito, Masaya; Hofmann, Stefan G

    2014-09-02

    Affective styles are assumed to be one of the underlying processes of depression and anxiety maintenance. However, little is known about the effect of depression and anxiety and the cultural influence of the factor structure. Here, we examined the cross-cultural validity of the Affective Style Questionnaire and its incremental validity for the influence on depression and anxiety. Affective Style Questionnaire was translated into Japanese using standard back-translation procedure. Japanese university students (N = 1,041) served as participants. Emotion Regulation Questionnaire, Acceptance and Action Questionnaire-II, Toronto Alexithymia Scale, Rumination and Reflection Questionnaire, Brief COPE, Self-Construal Scale, and Hospital Anxiety and Depression Scale were administered. Exploratory and confirmatory factor analyses showed that the Affective Style Questionnaire comprised four factors: Concealing, Adjusting, Holding and Tolerating (CFI = .92, TLI = .90, RMSEA = .07). The measure's convergent and discriminant validity was substantiated by its association with various emotion regulation measures. Regression analyses showed that negative influence of Adjusting, Holding, Reappraisal (β = -.17, -.19, -.30) and positive influence of Suppression (β = .23) were observed on depression. For anxiety, Adjusting and Reappraisal was negatively influenced (β = -.29, and -.18). Reliability and validity of the Affective Style Questionnaire was partly confirmed. Further study is needed to clarify the culturally dependent aspects of affective styles.

  13. Factors That Affect the Academic Success of Foreign Students at Cardinal Stritch University

    ERIC Educational Resources Information Center

    Annor, Peter

    2010-01-01

    There are limited studies in the literature on the factors that affect the academic success of foreign students in the United States. This ex post facto mixed method study investigated the factors that affect the academic success of foreign students at Cardinal Stitch University (CSU), a medium size, private university located in the Midwestern…

  14. Looking under the Bonnet: Factors Affecting Student Adoption of E-Learning Systems in Jordan

    ERIC Educational Resources Information Center

    Abbad, Muneer Mahmood; Morris, David; de Nahlik, Carmel

    2009-01-01

    The primary questions addressed in this paper are the following: what are the factors that affect students' adoption of an e-learning system and what are the relationships among these factors? This paper investigates and identifies some of the major factors affecting students' adoption of an e-learning system in a university in Jordan. E-learning…

  15. Institutional and Managerial Factors Affecting International Student Recruitment Management

    ERIC Educational Resources Information Center

    Ross, Mitchell; Heaney, Joo-Gim; Cooper, Maxine

    2007-01-01

    Purpose: The purpose of this paper is to investigate international student recruitment from an institutional perspective and to consider institutional factors that may affect recruitment. Design/methodology/approach: A qualitative study is undertaken in which education marketing practitioners are interviewed regarding aspects of international…

  16. Advantages of measuring the Q Stokes parameter in addition to the total radiance I in the detection of absorbing aerosols

    NASA Astrophysics Data System (ADS)

    Stamnes, Snorre; Fan, Yongzhen; Chen, Nan; Li, Wei; Tanikawa, Tomonori; Lin, Zhenyi; Liu, Xu; Burton, Sharon; Omar, Ali; Stamnes, Jakob J.; Cairns, Brian; Stamnes, Knut

    2018-05-01

    A simple but novel study was conducted to investigate whether an imager-type spectroradiometer instrument like MODIS, currently flying on board the Aqua and Terra satellites, or MERIS, which flew on board Envisat, could detect absorbing aerosols if they could measure the Q Stokes parameter in addition to the total radiance I, that is if they could also measure the linear polarization of the light. Accurate radiative transfer calculations were used to train a fast neural network forward model, which together with a simple statistical optimal estimation scheme was used to retrieve three aerosol parameters: aerosol optical depth at 869 nm, optical depth fraction of fine mode (absorbing) aerosols at 869 nm, and aerosol vertical location. The aerosols were assumed to be bimodal, each with a lognormal size distribution, located either between 0 and 2 km or between 2 and 4 km in the Earth's atmosphere. From simulated data with 3% random Gaussian measurement noise added for each Stokes parameter, it was found that by itself the total radiance I at the nine MODIS VIS channels was generally insufficient to accurately retrieve all three aerosol parameters (˜ 15% to 37% successful), but that together with the Q Stokes component it was possible to retrieve values of aerosol optical depth at 869 nm to ± 0.03, single-scattering albedo at 869 nm to ± 0.04, and vertical location in ˜ 65% of the cases. This proof-of-concept retrieval algorithm uses neural networks to overcome the computational burdens of using vector radiative transfer to accurately simulate top-of-atmosphere (TOA) total and polarized radiances, enabling optimal estimation techniques to exploit information from multiple channels. Therefore such an algorithm could, in concept, be readily implemented for operational retrieval of aerosol and ocean products from moderate or hyperspectral spectroradiometers.

  17. A spectral radiance comparison of a noise tube and a HgXe arc lamp between 60 GHz and 600 GHz

    NASA Technical Reports Server (NTRS)

    Heaney, J. B.; Stewart, K. P.; Boucarut, R. A.; Moller, K. D.; Zoeller, R.

    1987-01-01

    The relative spectral radiance of a noise tube, model TN-167, designed for the frequency range 90-140 GHz (3.3 mm to 2.1 mm) was compared to that from a 200-watt high pressure HgXe arc lamp over the wavelength region from 0.5 to about 5 mm. A Michelson Fourier transform spectrometer and a lamellar grating instrument were used in conjunction with liquid helium-cooled bolometers of NEP 10 to the -12th to 10 to the -14th watt/(Hz) exp 1/2 to measure relative spectral radiant power. With this instrumental arrangement, the noise tube exhibited a very sharp low frequency cutoff at about 2.2/cm. The HgXe arc lamp emitted more radiant power than the noise tube in the wavelength region below 3 mm (100 GHz) down to 0.5 mm. Above 3 mm, the noise tube had a stronger output. The noise tube spectral radiance shifted to lower frequencies when the input current was lowered from 125 mA to 50 mA.

  18. Psychological factors affecting medical condition: a new proposal for DSM-V.

    PubMed

    Fava, Giovanni A; Fabbri, Stefania; Sirri, Laura; Wise, Thomas N

    2007-01-01

    The DSM category of "psychological factors affecting medical condition" had virtually no impact on clinical practice. However, several clinically relevant psychosomatic syndromes have been described in the literature: disease phobia, persistent somatization, conversion symptoms, illness denial, demoralization, and irritable mood. These syndromes, in addition to the DSM definition of hypochondriasis, can yield clinical specification in the category of "psychological factors affecting medical condition" and eliminate the need for the highly criticized DSM classification of somatoform disorders. This new classification is supported by a growing body of research evidence and is in line with psychosomatic medicine as a recognized subspecialty.

  19. Artificially lit surface of Earth at night increasing in radiance and extent.

    PubMed

    Kyba, Christopher C M; Kuester, Theres; Sánchez de Miguel, Alejandro; Baugh, Kimberly; Jechow, Andreas; Hölker, Franz; Bennie, Jonathan; Elvidge, Christopher D; Gaston, Kevin J; Guanter, Luis

    2017-11-01

    A central aim of the "lighting revolution" (the transition to solid-state lighting technology) is decreased energy consumption. This could be undermined by a rebound effect of increased use in response to lowered cost of light. We use the first-ever calibrated satellite radiometer designed for night lights to show that from 2012 to 2016, Earth's artificially lit outdoor area grew by 2.2% per year, with a total radiance growth of 1.8% per year. Continuously lit areas brightened at a rate of 2.2% per year. Large differences in national growth rates were observed, with lighting remaining stable or decreasing in only a few countries. These data are not consistent with global scale energy reductions but rather indicate increased light pollution, with corresponding negative consequences for flora, fauna, and human well-being.

  20. Primary Radiometry for the mise-en-pratique: The Laser-Based Radiance Method Applied to a Pyrometer

    NASA Astrophysics Data System (ADS)

    Briaudeau, S.; Sadli, M.; Bourson, F.; Rougi, B.; Rihan, A.; Zondy, J.-J.

    2011-12-01

    A new setup has been implemented at LCM-LNE-CNAM for the determination "of the spectral responsivity of radiation thermometers for the determination" of the thermodynamic temperature of high-temperature blackbodies at the temperature of a metal-carbon eutectic phase transition. In this new setup, an innovative acoustic-optic modulator feedback loop is used to stabilize the radiance of a wavelength tunable laser. The effect of residual optical interferences on the calibration of a test pyrometer is analyzed. The full uncertainty budget is presented.

  1. Demographic and obstetric factors affecting women's sexual functioning during pregnancy.

    PubMed

    Abouzari-Gazafroodi, Kobra; Najafi, Fatemeh; Kazemnejad, Ehsan; Rahnama, Parvin; Montazeri, Ali

    2015-08-19

    Sexual desire and frequency of sexual relationships during pregnancy remains challenging. This study aimed to assess factors that affect women's sexual functioning during pregnancy. This was a cross sectional study carried out at prenatal care clinics of public health services in Iran. An author-designed structured questionnaire including items on socio-demographic characteristics, obstetric history, the current pregnancy, and women's sexual functioning during pregnancy was used to collect data. The generalized linear model was performed in order to find out factors that affect women's sexual functioning during pregnancy. In all, 518 pregnant women participated in the study. The mean age of participants was 26.4 years (SD = 4.7). Overall 309 women (59.7%) scored less than mean on sexual functioning. The results obtained from generalized linear model demonstrated that that lower education, unwanted pregnancy, earlier stage of pregnancy, older age, and longer duration of marriage were the most important factors contributing to disturbed sexual functioning among couples. The findings suggest that sexual function during pregnancy might be disturbed due to several factors. Indeed issues on sexual relationship should be included as part of prenatal care and reproductive health programs for every woman.

  2. Affect and Health Behavior Co-Occurrence: The Emerging Roles of Transdiagnostic Factors and Sociocultural Factors.

    PubMed

    Zvolensky, Michael J; Leventhal, Adam M

    2016-01-01

    The majority of scientific work addressing relations among affective states and health correlates has focused primarily on their co-occurrence and a limited range of health conditions. We have developed a Special Issue to highlight recent advances in this emerging field of work that addresses the nature and interplay between affective states and disorders, in terms of their impact and consequences from health status and behavior. This Special Issue is organized into three parts classified as (a) co-occurrence and interplay between (b) transdiagnostic factors and (c) sociocultural factors. It is hoped that this issue will (a) alert readers to the significance of this work at different levels of analysis, (b) illustrate the many domains currently being explored via innovative approaches, and (c) identify fecund areas for future systematic study. © The Author(s) 2016.

  3. Prevalence, pathophysiological mechanisms and factors affecting urolithiasis.

    PubMed

    Khan, Aslam

    2018-05-01

    The formation of urinary stone, urolithiasis, is one the oldest known disease affecting human throughout different civilizations and times. The exact pathophysiological mechanism of urolithiasis is not yet clear, as these calculi are of various types and too complex for simple understanding. A single theory cannot explain its formation; therefore, different theories are presented in various times for its explanation like free particle, fixed particle, Randall's plaque theory. In addition, various factors and components are identified that play an important role in the formation of these urinary calculi. In this review, composition of kidney stones, its prevalence/incidence, explanation of pathophysiological mechanisms and role of various factors; urinary pH, uric acid, parathyroid hormone, citrate, oxalate, calcium and macromolecules; osteopontin, matrix Gla protein, kidney injury molecules, urinary prothrombin fragment-1, Tamm-Horsfall protein, inter-α-inhibitors, have been discussed in detail.

  4. Factors that affect the development of nurses' competencies: a systematic review.

    PubMed

    Rizany, Ichsan; Hariyati, Rr Tutik Sri; Handayani, Hanny

    2018-02-01

    To investigate factors affecting the development of nursing competency based on a review of the literature. A systematic review was utilized. The articles were taken from the databases of Pro-Quest, ScienceDirect, SpringerLink, and Scopus. They were retrieved using the following keywords: nursing competence, nurse competencies and clinical competence. Twenty-one papers were selected. Competence development is a continuous process of improving knowledge, attitudes and skills, and is influenced by a myriad of factors. Six factors were identified that affected the development of nursing competence in our systematic review: (1) work experience, (2) type of nursing environment, (3) educational level achieved, (4) adherence to professionalism, (5) critical thinking, and (6) personal factors. Work experience and education were shown to significantly influence the development of competency of nurses. Nurse managers need to support staffing competence through ongoing education, mentoring-preceptorship training, and case-reflection-discussion teaching programs. Copyright © 2018 Elsevier España, S.L.U. All rights reserved.

  5. Factors Affecting Recruitment into Child and Adolescent Psychiatry Training

    ERIC Educational Resources Information Center

    Shaw, Jon A.; Lewis, John E.; Katyal, Shalini

    2010-01-01

    Objective: The authors studied the factors affecting the recruitment into child and adolescent psychiatry training in the United States. Methods: Medical students (n = 154) and general and child and adolescent psychiatry residents (n = 111) completed a questionnaire to evaluate career choice in child psychiatry (n = 265). Results: Compared with…

  6. Assessment of COSMIC radio occultation and AIRS hyperspectral IR sounder temperature products in the stratosphere using observed radiances

    NASA Astrophysics Data System (ADS)

    Feltz, M. L.; Knuteson, R. O.; Revercomb, H. E.

    2017-08-01

    Upper air temperature is defined as an essential climate variable by the World Meteorological Organization. Two remote sensing technologies being promoted for monitoring stratospheric temperatures are GPS radio occultation (RO) and spectrally resolved IR radiances. This study assesses RO and hyperspectral IR sounder derived temperature products within the stratosphere by comparing IR spectra calculated from GPS RO and IR sounder products to coincident IR observed radiances, which are used as a reference standard. RO dry temperatures from the University Corporation for Atmospheric Research (UCAR) Constellation Observing System for Meteorology, Ionosphere, and Climate (COSMIC) mission are compared to NASA Atmospheric Infrared Sounder (AIRS) retrievals using a previously developed profile-to-profile collocation method and vertical temperature averaging kernels. Brightness temperatures (BTs) are calculated for both COSMIC and AIRS temperature products and are then compared to coincident AIRS measurements. The COSMIC calculated minus AIRS measured BTs exceed the estimated 0.5 K measurement uncertainty for the winter time extratropics around 35 hPa. These differences are attributed to seasonal UCAR COSMIC biases. Unphysical vertical oscillations are seen in the AIRS L2 temperature product in austral winter Antarctic regions, and results imply a small AIRS tropical warm bias around 35 hPa in the middle stratosphere.

  7. Laplace-transform-based method to calculate back-reflected radiance from an isotropically scattering half-space

    NASA Astrophysics Data System (ADS)

    Rinzema, K.; Hoenders, B. J.; Ferwerda, H. A.

    1997-07-01

    We present a method to determine the back-reflected radiance from an isotropically scattering half-space with matched boundary. This method has the advantage that it leads very quickly to the relevant equations, the numerical solution of which is also quite easy. Essentially, the method is derived from a mathematical criterion that effectively forbids the existence of solutions to the transport equation which grow exponentially as one moves away from the surface and deeper into the medium. Preliminary calculations for infinitely wide beams yield results which agree very well with what is found in the literature.

  8. A review of affecting factors on sexual satisfaction in women.

    PubMed

    Shahhosseini, Zohreh; Gardeshi, Zeinab Hamzeh; Pourasghar, Mehdi; Salehi, Fariba

    2014-12-01

    Sex is a complex, important and sensitive issue in human being and interwoven with the whole of human existence. Given the serious changes in attitude, function and behavior in sex, the need to address sexual function, especially sexual satisfaction, is felt completely. Sexual satisfaction has a very important role in creating marital satisfaction and any defect in sexual satisfaction is significantly associated with risky sexual behaviors, serious mental illness, social crimes and ultimately divorce. The aim of this study was to explore affecting factors on sexual satisfaction in women based on an overview in scientific database. In this narrative review the researchers searched MEDLINE database, Google Scholar and Science Direct as well as Persian database like Scientific Information Database with search terms of sexual satisfaction and sexual function, restricted to English/ Persian language, during the 20 years ago. Then those articles written by renowned experts were selected. In this regard, 57 articles have been reviewed, which 30 articles related to this research have been extracted. The findings were divided in to four categories including: Demographic factors, Pathophysiological factors, Psychological factors and Sociocultural factors. Sexuality, especially sexual intimacy is sophisticated and yet elegant affair that the other persons has different definitions and different functions. Discrepancies in the results of the studies show that analysis of factors affecting sexual satisfaction regardless of the women's' sociocultural context, religious beliefs, and personal attitudes is undoubtedly inefficient, unscientific and irrational.

  9. Factors affecting yearly and monthly visits to Taipei Zoo

    NASA Astrophysics Data System (ADS)

    Su, Ai-Tsen; Lin, Yann-Jou

    2018-02-01

    This study investigated factors affecting yearly and monthly numbers of visits to Taipei Zoo. Both linear and nonlinear regression models were used to estimate yearly visits. The results of both models showed that the "opening effect" and "animal star effect" had a significantly positive effect on yearly visits, while a SARS outbreak had a negative effect. The number of years had a significant influence on yearly visits. Results showed that the nonlinear model had better explanatory power and fitted the variations of visits better. Results of monthly model showed that monthly visits were significantly influenced by time fluctuations, weather conditions, and the animal star effect. Chinese New Year, summer vacation, numbers of holidays, and animal star exhibitions increased the number of monthly visits, while the number of days with temperatures at or below 15 °C, the number of days with temperatures at or above 30 °C, and the number of rainy days had significantly negative effects. Furthermore, the model of monthly visits showed that the animal star effect could last for over two quarters. The results of this study clarify the factors affecting visits to an outdoor recreation site and confirm the importance of meteorological factors to recreation use.

  10. A Qualitative Study of Factors Affecting Morale in Psychiatry Residency Training.

    PubMed

    Caravella, Rachel A; Robinson, Lee A; Wilets, Ilene; Weinberg, Michael; Cabaniss, Deborah L; Cutler, Janis L; Kymissis, Carisa; Arbuckle, Melissa R

    2016-10-01

    Resident morale is an important yet poorly understood aspect of the residency training experience. Despite implications for program quality, resident satisfaction, patient care, and recruitment, little is known about the variables influencing this complex phenomenon. This study sought to identify important factors affecting morale in psychiatry residency training. The authors conducted four semi-structured focus groups at a moderately sized, urban, psychiatry residency program during the 2013-2014 academic year. They used qualitative data analysis techniques, including grounded theory and content analysis, to identify key themes affecting resident morale across training levels. Twenty-seven residents participated in the focus groups with equal distribution across post-graduate years (PGY) 1-4. Five major conceptual categories affecting resident morale emerged: Sense of Community, Individual Motivators, Clinical Work, Feeling Cared For, and Trust in the Administration. Morale is an important topic in residency education. The qualitative results suggest that factors related to a Sense of Community and Individual Motivators generally enhanced resident morale whereas factors related to a lack of Feeling Cared For and Trust in the Administration tended to contribute to lower morale. The authors describe the possible interventions to promote stronger program morale suggested by these findings.

  11. Factors affecting the overcrowding in outpatient healthcare

    PubMed Central

    Bahadori, Mohammadkarim; Teymourzadeh, Ehsan; Ravangard, Ramin; Raadabadi, Mehdi

    2017-01-01

    Background: The expansion of outpatient services and the desire to provide more outpatient care than inpatient care create some problems such as the overcrowding in the outpatient clinics. Given the importance of overcrowding in the outpatient clinics, this qualitative study aimed to determine the factors influencing the overcrowding in the specialty and subspecialty clinic of a teaching hospital. Materials and Methods: This was a qualitative study conducted in the specialty and subspecialty clinic of a hospital using content analysis method in the period of January to March 2014. The study population was all managers and heads of the outpatient wards. The studied sample consisted of 22 managers of the clinic wards who were selected using the purposive sampling method. The required data was collected using semi-structured interviews. The collected data was analyzed using conventional content analysis and the MAXQDA 10.0 software. Results: Three themes were identified as the main factors affecting the overcrowding including the internal positive factors, internal negative factors, and external factors. Conclusions: Despite the efforts made to eliminate overcrowding, and reduce waiting times and increase access to the services for patients, the problem of overcrowding still has remained unresolved. In addition, the use of some strategies such as clarifying the working processes of the clinic for staff and patients and the relationships between the clinic and other wards especially emergency department, as well as using a simple triage system on the patients’ arrival at the clinic are recommended. PMID:28546986

  12. Recruitment and retention: factors that affect pericyte migration

    PubMed Central

    Aguilera, Kristina Y.

    2013-01-01

    Pericytes are critical for vascular morphogenesis and contribute to several pathologies, including cancer development and progression. The mechanisms governing pericyte migration and differentiation are complex and have not been fully established. Current literature suggests that platelet-derived growth factor/platelet-derived growth factor receptor-β, sphingosine 1-phosphate/endothelial differentiation gene-1, angiopoietin-1/tyrosine kinase with immunoglobulin-like and EGF-like domains 2, angiopoietin-2/tyros-ine kinase with immunoglobulin-like and EGF-like domains 2, transforming growth factor β/activin receptor-like kinase 1, transforming growth factor β/activin receptor-like kinase 5, Semaphorin-3A/Neuropilin, and matrix metalloproteinase activity regulate the recruitment of pericytes to nascent vessels. Interestingly, many of these pathways are directly affected by secreted protein acidic and rich in cysteine (SPARC). Here, we summarize the function of these factors in pericyte migration and discuss if and how SPARC might infuence these activities and thus provide an additional layer of control for the recruitment of vascular support cells. Additionally, the consequences of targeted inhibition of pericytes in tumors and the current understanding of pericyte recruitment in pathological environments are discussed. PMID:23912898

  13. Factors Affecting Role Stress and Burnout among School Counselors

    ERIC Educational Resources Information Center

    Willingham, Wendy Elizabeth

    2009-01-01

    The purpose of this study is to determine factors affecting role stress and burnout among practicing school counselors as measured by the Maslach Burnout Inventory-Educators Survey (MBI-ES) and the Role Conflict and Ambiguity Scale. The MBI-ES utilizes three subscales to measure burnout: emotional exhaustion, depersonalization, and personal…

  14. Factors affecting species distribution predictions: A simulation modeling experiment

    Treesearch

    Gordon C. Reese; Kenneth R. Wilson; Jennifer A. Hoeting; Curtis H. Flather

    2005-01-01

    Geospatial species sample data (e.g., records with location information from natural history museums or annual surveys) are rarely collected optimally, yet are increasingly used for decisions concerning our biological heritage. Using computer simulations, we examined factors that could affect the performance of autologistic regression (ALR) models that predict species...

  15. Motivational Factors Affecting Online Learning by Japanese MBA Students

    ERIC Educational Resources Information Center

    Kikuchi, Hisayo

    2006-01-01

    In Japan, Internet based learning is still at an early stage. However, adult learners in Japanese society expect the development of flexible e-learning programs. This case study examines motivational factors affecting online learning in a Japanese and Australian MBA program, using observations, interviews and a questionnaire survey. The data were…

  16. Analysis of extrinsic and intrinsic factors affecting event related desynchronization production.

    PubMed

    Takata, Yohei; Kondo, Toshiyuki; Saeki, Midori; Izawa, Jun; Takeda, Kotaro; Otaka, Yohei; It, Koji

    2012-01-01

    Recently there has been an increase in the number of stroke patients with motor paralysis. Appropriate re-afferent sensory feedback synchronized with a voluntary motor intention would be effective for promoting neural plasticity in the stroke rehabilitation. Therefore, BCI technology is considered to be a promising approach in the neuro-rehabilitation. To estimate human motor intention, an event-related desynchronization (ERD), a feature of electroencephalogram (EEG) evoked by motor execution or motor imagery is usually used. However, there exists various factors that affect ERD production, and its neural mechanism is still an open question. As a preliminary stage, we evaluate mutual effects of intrinsic (voluntary motor imagery) and extrinsic (visual and somatosensory stimuli) factors on the ERD production. Experimental results indicate that these three factors are not always additively interacting with each other and affecting the ERD production.

  17. New strategies in the assessment of psychological factors affecting medical conditions.

    PubMed

    Sirri, Laura; Fabbri, Stefania; Fava, Giovanni A; Sonino, Nicoletta

    2007-12-01

    In this article, we examine research that may lead to a better assessment of psychological factors affecting medical conditions. We performed a review of the psychosomatic literature using both Medline and manual searches. We selected papers that were judged to be relevant to new strategies of assessment, with particular reference to the use of the Diagnostic Criteria for Psychosomatic Research. We assessed 8 areas concerned with the assessment of psychological factors in the setting of medical disease: hypochondriasis, disease phobia, persistent somatization, conversion symptoms, illness denial, demoralization, irritable mood, and Type A behavior. A new subclassification of the Diagnostic and Statistical Manual of Mental Disorders (5th ed. [DSM-V]; not yet published) category of psychological factors affecting physical conditions appears to be feasible and may provide the clinician with better tools for identifying psychological distress.

  18. Laboratory measurements of radiance and reflectance spectra of dilute primary-treated sewage sludge

    NASA Technical Reports Server (NTRS)

    Usry, J. W.; Witte, W. G.; Whitlock, C. H.; Gurganus, E. A.

    1977-01-01

    The feasibility of remotely monitoring ocean dumping of waste products such as acid and sewage sludge is evaluated. The laboratory arrangement, solar simulator, and test results from three experiments conducted in the laboratory are described. Radiance and reflectance spectra are presented for primary-treated sewage sludge mixed with two types of base water. Results indicate that upwelled reflectance varies in a near-linear manner with concentration and that the sludge has a practically flat signal response between 420 and 970 nm. Well-defined upwelled reflectance spectra were obtained for the sewage-sludge mixtures at all wavelengths and concentrations. The spectral-reflectance values appeared to be influenced by the type of base water, but this influence was small, especially for the mixtures with low concentrations of sewage sludge.

  19. Multifactorial analysis of factors affecting recurrence of stroke in Japan.

    PubMed

    Omori, Toyonori; Kawagoe, Masahiro; Moriyama, Michiko; Yasuda, Takeshi; Ito, Yasuhiro; Hyakuta, Takeshi; Nagatsuka, Kazuyuki; Matsumoto, Masayasu

    2015-03-01

    Data on factors affecting stroke recurrence are relatively limited. The authors examined potential factors affecting stroke recurrence, retrospectively. The study participants were 1087 patients who were admitted to stroke centers suffering from first-ever ischemic stroke and returned questionnaires with usable information after discharge. The authors analyzed the association between clinical parameters of the patients and their prognosis. Recurrence rate of during an average of 2 years after discharge was 21.3%, and there were differences among stroke subtypes. It was found that the disability level of the patients after discharge correlated well with the level at discharge (r s = 0.66). Multivariate logistic regression analysis of the data shows that modified Rankin Scale score, National Institute of Health Stroke Scale score, gender, age, and family history had statistically significant impacts on stroke recurrence, and the impact was different depending on subtypes. These findings suggest that aggressive and persistent health education for poststroke patients and management of risk factors are essential to reduce stroke recurrence. © 2012 APJPH.

  20. Feasibility of quasi-random band model in evaluating atmospheric radiance

    NASA Technical Reports Server (NTRS)

    Tiwari, S. N.; Mirakhur, N.

    1980-01-01

    The use of the quasi-random band model in evaluating upwelling atmospheric radiation is investigated. The spectral transmittance and total band adsorptance are evaluated for selected molecular bands by using the line by line model, quasi-random band model, exponential sum fit method, and empirical correlations, and these are compared with the available experimental results. The atmospheric transmittance and upwelling radiance were calculated by using the line by line and quasi random band models and were compared with the results of an existing program called LOWTRAN. The results obtained by the exponential sum fit and empirical relations were not in good agreement with experimental results and their use cannot be justified for atmospheric studies. The line by line model was found to be the best model for atmospheric applications, but it is not practical because of high computational costs. The results of the quasi random band model compare well with the line by line and experimental results. The use of the quasi random band model is recommended for evaluation of the atmospheric radiation.

  1. Mathematics Performance and the Role Played by Affective and Background Factors

    ERIC Educational Resources Information Center

    Grootenboer, Peter; Hemmings, Brian

    2007-01-01

    In this article, we report on a study examining those factors which contribute to the mathematics performance of a sample of children aged between 8 and 13 years. The study was designed specifically to consider the potency of a number of mathematical affective factors, as well as background characteristics (viz., gender, ethnicity, and…

  2. Factors Affecting Career Decision Making of Mexican and Mexican-American Students.

    ERIC Educational Resources Information Center

    Newlon, Betty J.; Borboa, Roman

    The purpose of this research was to identify the self-reported factors affecting the career decision making of Mexican and Mexican-American students. It was hypothesized that the factor clusters would differ between the two sample populations, Mexican and Mexican-American. It was also hypothesized that these clusters would differ from six clusters…

  3. Industry Training: The Factors that Affect Demand. Discussion Paper.

    ERIC Educational Resources Information Center

    Smith, A.; Roberts, P.; Noble, C.; Hayton, G.; Thorne, E.

    A study was conducted in Australia, to determine the factors that affect demand for job training. The study consisted of 30 detailed industry case studies, an industry analysis, and a literature review. Each case study examined current training practices, training decision making in the business, and the determinants of training for the…

  4. An Analysis of Factors Affecting Community College Students' Expectations on E-Learning

    ERIC Educational Resources Information Center

    Kilic-Cakmak, Ebru; Karatas, Sercin; Ocak, Mehmet Akif

    2009-01-01

    There are many factors that affect the e-learning process. Instructor, assessment and evaluation, communication, and technical support are among the leading factors. It is obvious that these factors influence the effectiveness of e-learning and may be related to different expectations of e-learners. Therefore, this study focuses on examining the…

  5. Lengths of Orthologous Prokaryotic Proteins Are Affected by Evolutionary Factors

    PubMed Central

    Tatarinova, Tatiana; Dien Bard, Jennifer; Cohen, Irit

    2015-01-01

    Proteins of the same functional family (for example, kinases) may have significantly different lengths. It is an open question whether such variation in length is random or it appears as a response to some unknown evolutionary driving factors. The main purpose of this paper is to demonstrate existence of factors affecting prokaryotic gene lengths. We believe that the ranking of genomes according to lengths of their genes, followed by the calculation of coefficients of association between genome rank and genome property, is a reasonable approach in revealing such evolutionary driving factors. As we demonstrated earlier, our chosen approach, Bubble-sort, combines stability, accuracy, and computational efficiency as compared to other ranking methods. Application of Bubble Sort to the set of 1390 prokaryotic genomes confirmed that genes of Archaeal species are generally shorter than Bacterial ones. We observed that gene lengths are affected by various factors: within each domain, different phyla have preferences for short or long genes; thermophiles tend to have shorter genes than the soil-dwellers; halophiles tend to have longer genes. We also found that species with overrepresentation of cytosines and guanines in the third position of the codon (GC3 content) tend to have longer genes than species with low GC3 content. PMID:26114113

  6. Lengths of Orthologous Prokaryotic Proteins Are Affected by Evolutionary Factors.

    PubMed

    Tatarinova, Tatiana; Salih, Bilal; Dien Bard, Jennifer; Cohen, Irit; Bolshoy, Alexander

    2015-01-01

    Proteins of the same functional family (for example, kinases) may have significantly different lengths. It is an open question whether such variation in length is random or it appears as a response to some unknown evolutionary driving factors. The main purpose of this paper is to demonstrate existence of factors affecting prokaryotic gene lengths. We believe that the ranking of genomes according to lengths of their genes, followed by the calculation of coefficients of association between genome rank and genome property, is a reasonable approach in revealing such evolutionary driving factors. As we demonstrated earlier, our chosen approach, Bubble-sort, combines stability, accuracy, and computational efficiency as compared to other ranking methods. Application of Bubble Sort to the set of 1390 prokaryotic genomes confirmed that genes of Archaeal species are generally shorter than Bacterial ones. We observed that gene lengths are affected by various factors: within each domain, different phyla have preferences for short or long genes; thermophiles tend to have shorter genes than the soil-dwellers; halophiles tend to have longer genes. We also found that species with overrepresentation of cytosines and guanines in the third position of the codon (GC3 content) tend to have longer genes than species with low GC3 content.

  7. Artificially lit surface of Earth at night increasing in radiance and extent

    PubMed Central

    Kyba, Christopher C. M.; Kuester, Theres; Sánchez de Miguel, Alejandro; Baugh, Kimberly; Jechow, Andreas; Hölker, Franz; Bennie, Jonathan; Elvidge, Christopher D.; Gaston, Kevin J.; Guanter, Luis

    2017-01-01

    A central aim of the “lighting revolution” (the transition to solid-state lighting technology) is decreased energy consumption. This could be undermined by a rebound effect of increased use in response to lowered cost of light. We use the first-ever calibrated satellite radiometer designed for night lights to show that from 2012 to 2016, Earth’s artificially lit outdoor area grew by 2.2% per year, with a total radiance growth of 1.8% per year. Continuously lit areas brightened at a rate of 2.2% per year. Large differences in national growth rates were observed, with lighting remaining stable or decreasing in only a few countries. These data are not consistent with global scale energy reductions but rather indicate increased light pollution, with corresponding negative consequences for flora, fauna, and human well-being. PMID:29181445

  8. [Study on the characteristics of radiance calibration using nonuniformity extended source].

    PubMed

    Wang, Jian-Wei; Huang, Min; Xiangli, Bin; Tu, Xiao-Long

    2013-07-01

    Integrating sphere and diffuser are always used as extended source, and they have different effects on radiance calibration of imaging spectrometer with parameter difference. In the present paper, a mathematical model based on the theory of radiative transfer and calibration principle is founded to calculate the irradiance and calibration coefficients on CCD, taking relatively poor uniformity lights-board calibration system for example. The effects of the nonuniformity on the calibration was analyzed, which makes up the correlation of calibration coefficient matrix under ideal and unideal situation. The results show that the nonuniformity makes the viewing angle and the position of the point of intersection of the optical axis and the diffuse reflection plate have relatively large effects on calibration, while the observing distance's effect is small; under different viewing angles, a deviation value can be found that makes the calibration results closest to the desired results. So, the calibration error can be reduced by choosing appropriate deviation value.

  9. A Study of the Technological, Instructional, and Motivational Factors Affecting PHR Certification Exam Outcomes

    ERIC Educational Resources Information Center

    Bonner, David M.

    2012-01-01

    Although previous studies have considered the factors affecting other certification exam outcomes, they have not examined those that are related to performance on the Professional in Human Resources (PHR) exam. In response to that need, this study specifically investigates technology and training factors that affect self-efficacy and self-set…

  10. [Factors affecting residual stones after percutaneous nephrolithotomy in patients with renal calculus].

    PubMed

    Qiao, Mingzhou; Zhang, Haifang; Zhou, Chenlong

    2015-11-24

    To explore the factors affecting the residual stones after percutaneous nephrolithotomy (PCNL) in patients with renal calculus. A retrospective analysis was performed for 1 200 patients who were affected by renal calculus and treated with PCNL between Jan 2008 and May 2014 in People's Hospital of Anyang City. Among those patients, 16 were diagnosed as bilateral renal stone and had two successive operations. The size, location and number of stones, previous history of surgery, the degree of hydronephrosis, urinary infection were included in the univariate analysis. Significant factors in univariate analysis were included in the multivariate analysis to determine factors affecting stone residual. A total of 385 cases developed stone residual after surgery. The overall residual rate was 31.7%. In univariate analysis, renal pelvis combined with caliceal calculus (P=0.006), stone size larger than 4 cm (P=0.005), stone number more than 4 (P=0.002), the amount of bleeding more than 200 ml (P=0.025), operation time longer than 120 minutes (P=0.028) were associated with an increased rate of stone residual. When subjected to the Cox multivariate analysis, the independent risk factors for residual stones were renal pelvis combined with caliceal calculus (P=0.049), stone size larger than 4 cm (P=0.038) and stone number more than 4 (P=0.018). Factors affecting the incidence of residual stones after PCNL are the size, location and number of stones. Larger size stone and the presence of renal pelvis combined with caliceal calculus are significantly associated with residual stones. Nevertheless, stone number less than 4 indicates an increased stone clearance rate.

  11. Factors affecting decision-making of patients choosing acupuncture in a public hospital.

    PubMed

    Sayampanathan, Andrew Arjun; Koh, Thean Howe Bryan; Kong, Keng He; Low, Yin Peng

    2015-11-01

    With increasing evidence to support its practice, acupuncture has been integrated within many hospitals around the world. The purpose of this study is to understand the factors affecting decision making of patients as they select acupuncture treatment for their medical conditions and symptoms within a public hospital. A qualitative study consisting of in depth interviews with 14 patients was conducted. All patients attended an acupuncture clinic within a public hospital. Data collected was analysed via thematic analysis. Four main factor groups affecting decision making of patients were identified- factors affecting the level and value of patient-centric care, the confidence and trust patients place within the acupuncture service, the presence of collaborative efforts between acupuncturists and Western medicine practitioners, and the knowledge, culture and belief society has regarding the role of acupuncture and Western medicine. All participants interviewed had more than one factor group present as enablers toward their eventual selection of acupuncture for ailment management. It was also noted that although the majority of participants had sufficient knowledge regarding acupuncture, there were a select few who had misperceptions or no knowledge regarding certain aspects of acupuncture. There may be certain patterns in the way patients choose to utilise acupuncture services in public hospitals. Further studies should also be carried out in other public hospitals to analyse the factor groups identified further.

  12. Estimating nocturnal opaque ice cloud optical depth from MODIS multispectral infrared radiances using a neural network method

    NASA Astrophysics Data System (ADS)

    Minnis, Patrick; Hong, Gang; Sun-Mack, Szedung; Smith, William L.; Chen, Yan; Miller, Steven D.

    2016-05-01

    Retrieval of ice cloud properties using IR measurements has a distinct advantage over the visible and near-IR techniques by providing consistent monitoring regardless of solar illumination conditions. Historically, the IR bands at 3.7, 6.7, 11.0, and 12.0 µm have been used to infer ice cloud parameters by various methods, but the reliable retrieval of ice cloud optical depth τ is limited to nonopaque cirrus with τ < 8. The Ice Cloud Optical Depth from Infrared using a Neural network (ICODIN) method is developed in this paper by training Moderate Resolution Imaging Spectroradiometer (MODIS) radiances at 3.7, 6.7, 11.0, and 12.0 µm against CloudSat-estimated τ during the nighttime using 2 months of matched global data from 2007. An independent data set comprising observations from the same 2 months of 2008 was used to validate the ICODIN. One 4-channel and three 3-channel versions of the ICODIN were tested. The training and validation results show that IR channels can be used to estimate ice cloud τ up to 150 with correlations above 78% and 69% for all clouds and only opaque ice clouds, respectively. However, τ for the deepest clouds is still underestimated in many instances. The corresponding RMS differences relative to CloudSat are ~100 and ~72%. If the opaque clouds are properly identified with the IR methods, the RMS differences in the retrieved optical depths are ~62%. The 3.7 µm channel appears to be most sensitive to optical depth changes but is constrained by poor precision at low temperatures. A method for estimating total optical depth is explored for estimation of cloud water path in the future. Factors affecting the uncertainties and potential improvements are discussed. With improved techniques for discriminating between opaque and semitransparent ice clouds, the method can ultimately improve cloud property monitoring over the entire diurnal cycle.

  13. Factors that Affect Poverty Areas in North Sumatera Using Discriminant Analysis

    NASA Astrophysics Data System (ADS)

    Nasution, D. H.; Bangun, P.; Sitepu, H. R.

    2018-04-01

    In Indonesia, especially North Sumatera, the problem of poverty is one of the fundamental problems that become the focus of government both central and local government. Although the poverty rate decreased but the fact is there are many people who are poor. Poverty happens covers several aspects such as education, health, demographics, and also structural and cultural. This research will discuss about several factors such as population density, Unemployment Rate, GDP per capita ADHK, ADHB GDP per capita, economic growth and life expectancy that affect poverty in Indonesia. To determine the factors that most influence and differentiate the level of poverty of the Regency/City North Sumatra used discriminant analysis method. Discriminant analysis is one multivariate analysis technique are used to classify the data into a group based on the dependent variable and independent variable. Using discriminant analysis, it is evident that the factor affecting poverty is Unemployment Rate.

  14. Factors Other than GFR Affecting Serum Cystatin C Levels

    PubMed Central

    Stevens, Lesley A; Schmid, Christopher H.; Greene, Tom; Li, Liang; Beck, Gerald J; Joffe, Marshall; Froissart, Marc; Kusek, John; Zhang, Yaping (Lucy); Coresh, Josef; Levey, Andrew S

    2015-01-01

    Cystatin C is gaining acceptance as an endogenous filtration marker. Factors other than glomerular filtration rate (GFR) that affect the serum level have not been carefully studied. In a cross-sectional analysis of a pooled dataset of participants from clinical trials and a clinical population with chronic kidney disease (N=3418), we related serum levels of cystatin C and creatinine to clinical and biochemical variables after adjustment for GFR using errors-in-variables models to account for GFR measurement error. GFR was measured as urinary clearance of 125I-iothalamate and 15Cr-EDTA. Cystatin C was assayed at a single laboratory and creatinine was standardized to reference methods. Mean (SD) creatinine and cystatin C were 2.1 (1.1) mg/dL and 1.8 (0.8) mg/L, respectively. After adjustment for GFR, cystatin C was 4.3% lower for every 20 years of age, 9.2% lower for female sex but only 1.9% lower in blacks. Diabetes was associated with 8.5% higher levels of cystatin C and 3.9% lower levels of creatinine. Higher C-reactive protein and white blood cell count and lower serum albumin were associated with higher levels of cystatin C and lower levels of creatinine. Adjustment for age, sex and race had a greater effect on association of factors with creatinine than cystatin C. In conclusion, cystatin C is affected by factors other than GFR. Clinicians should consider these factors when interpreting the serum levels or GFR estimates from cystatin C. PMID:19119287

  15. Validating YouTube Factors Affecting Learning Performance

    NASA Astrophysics Data System (ADS)

    Pratama, Yoga; Hartanto, Rudy; Suning Kusumawardani, Sri

    2018-03-01

    YouTube is often used as a companion medium or a learning supplement. One of the educational places that often uses is Jogja Audio School (JAS) which focuses on music production education. Music production is a difficult material to learn, especially at the audio mastering. With tutorial contents from YouTube, students find it easier to learn and understand audio mastering and improved their learning performance. This study aims to validate the role of YouTube as a medium of learning in improving student’s learning performance by looking at the factors that affect student learning performance. The sample involves 100 respondents from JAS at audio mastering level. The results showed that student learning performance increases seen from factors that have a significant influence of motivation, instructional content, and YouTube usefulness. Overall findings suggest that YouTube has a important role to student learning performance in music production education and as an innovative and efficient learning medium.

  16. Beyond Negative Pain-Related Psychological Factors: Resilience Is Related to Lower Pain Affect in Healthy Adults.

    PubMed

    Hemington, Kasey S; Cheng, Joshua C; Bosma, Rachael L; Rogachov, Anton; Kim, Junseok A; Davis, Karen D

    2017-09-01

    Resilience, a characteristic that enhances adaptation in response to stressful events, is a positive psychological factor that can predict and modulate health outcomes. However, resilience is rarely considered in pain research. Conversely, negative psychological factors (eg, anxiety, depression) are known to be related to the affective dimension of pain. It is critical to understand all potential psychological drivers of pain affect, a prominent component of chronic pain. We tested the hypothesis that higher resilience is associated with lower pain affect, above and beyond the predictive value of negative psychological factors. Healthy adults underwent psychophysical testing to acquire ratings of heat pain intensity and unpleasantness and completed the Resilience Scale, the State-Trait Anxiety Inventory (trait form), Beck Depression Inventory, Pain Catastrophizing Scale, and the Pain Vigilance and Attention Questionnaire. Multiple regression modeling (n = 68) showed resilience to be a negatively associated with pain affect (unpleasantness). Furthermore, in individuals with higher anxiety scores, resilience was protective against higher pain affect. This highlights the importance of resilience, a positive psychological factor, in the affective dimension of pain. This study is the first to assess a positive psychological factor and experimental pain affect, and has the potential to improve prediction of and treatment strategies for clinical pain. We report that resilience, a positive psychological factor, interacts with anxiety and is associated with heat pain affect (unpleasantness) in healthy individuals. Resilience may provide predictive value of chronic pain affect and treatment outcomes, and could be a target for behavioral therapy. Copyright © 2017 American Pain Society. Published by Elsevier Inc. All rights reserved.

  17. A study of the factors affecting the range of airplanes

    NASA Technical Reports Server (NTRS)

    Biermann, David

    1937-01-01

    A study was made of the most important factors affecting the range of airplanes. Numerical examples are given showing the effects of different variables on the range of a two-engine airplane. The takeoff problems of long-range airplanes are analyzed.

  18. An Empirically Derived Taxonomy of Factors Affecting Physicians' Willingness to Disclose Medical Errors

    PubMed Central

    Kaldjian, Lauris C; Jones, Elizabeth W; Rosenthal, Gary E; Tripp-Reimer, Toni; Hillis, Stephen L

    2006-01-01

    BACKGROUND Physician disclosure of medical errors to institutions, patients, and colleagues is important for patient safety, patient care, and professional education. However, the variables that may facilitate or impede disclosure are diverse and lack conceptual organization. OBJECTIVE To develop an empirically derived, comprehensive taxonomy of factors that affects voluntary disclosure of errors by physicians. DESIGN A mixed-methods study using qualitative data collection (structured literature search and exploratory focus groups), quantitative data transformation (sorting and hierarchical cluster analysis), and validation procedures (confirmatory focus groups and expert review). RESULTS Full-text review of 316 articles identified 91 impeding or facilitating factors affecting physicians' willingness to disclose errors. Exploratory focus groups identified an additional 27 factors. Sorting and hierarchical cluster analysis organized factors into 8 domains. Confirmatory focus groups and expert review relocated 6 factors, removed 2 factors, and modified 4 domain names. The final taxonomy contained 4 domains of facilitating factors (responsibility to patient, responsibility to self, responsibility to profession, responsibility to community), and 4 domains of impeding factors (attitudinal barriers, uncertainties, helplessness, fears and anxieties). CONCLUSIONS A taxonomy of facilitating and impeding factors provides a conceptual framework for a complex field of variables that affects physicians' willingness to disclose errors to institutions, patients, and colleagues. This taxonomy can be used to guide the design of studies to measure the impact of different factors on disclosure, to assist in the design of error-reporting systems, and to inform educational interventions to promote the disclosure of errors to patients. PMID:16918739

  19. Factors Affecting Teen Involvement in Pennsylvania 4-H Programming

    ERIC Educational Resources Information Center

    Gill, Bart E.; Ewing, John C.; Bruce, Jacklyn A.

    2010-01-01

    The study reported here determined the factors that affect teen involvement in 4-H programming. The design of the study was descriptive and correlational in nature. Using a purposive sampling procedure, a survey questionnaire was distributed to all (N=214) 4-H members attending the 4-H State Leadership Conference. The major findings of the study…

  20. [Factors affecting the quality of cardiopulmonary resuscitation in inpatient units: perception of nurses].

    PubMed

    Citolino, Clairton Marcos Filho; Santos, Eduesley Santana; Silva, Rita de Cassia Gengo E; Nogueira, Lilia de Souza

    2015-12-01

    To identify, in the perception of nurses, the factors that affect the quality of cardiopulmonary resuscitation (CPR) in adult inpatient units, and investigate the influence of both work shifts and professional experience length of time in the perception of these factors. A descriptive, exploratory study conducted at a hospital specialized in cardiology and pneumology with the application of a questionnaire to 49 nurses working in inpatient units. The majority of nurses reported that the high number of professionals in the scenario (75.5%), the lack of harmony (77.6%) or stress of any member of staff (67.3%), lack of material and/or equipment failure (57.1%), lack of familiarity with the emergency trolleys (98.0%) and presence of family members at the beginning of the cardiopulmonary arrest assistance (57.1%) are factors that adversely affect the quality of care provided during CPR. Professional experience length of time and the shift of nurses did not influence the perception of these factors. The identification of factors that affect the quality of CPR in the perception of nurses serves as parameter to implement improvements and training of the staff working in inpatient units.

  1. Errors induced by the neglect of polarization in radiance calculations for Rayleigh-scattering atmospheres

    NASA Technical Reports Server (NTRS)

    Mishchenko, M. I.; Lacis, A. A.; Travis, L. D.

    1994-01-01

    Although neglecting polarization and replacing the rigorous vector radiative transfer equation by its approximate scalar counterpart has no physical background, it is a widely used simplification when the incident light is unpolarized and only the intensity of the reflected light is to be computed. We employ accurate vector and scalar multiple-scattering calculations to perform a systematic study of the errors induced by the neglect of polarization in radiance calculations for a homogeneous, plane-parallel Rayleigh-scattering atmosphere (with and without depolarization) above a Lambertian surface. Specifically, we calculate percent errors in the reflected intensity for various directions of light incidence and reflection, optical thicknesses of the atmosphere, single-scattering albedos, depolarization factors, and surface albedos. The numerical data displayed can be used to decide whether or not the scalar approximation may be employed depending on the parameters of the problem. We show that the errors decrease with increasing depolarization factor and/or increasing surface albedo. For conservative or nearly conservative scattering and small surface albedos, the errors are maximum at optical thicknesses of about 1. The calculated errors may be too large for some practical applications, and, therefore, rigorous vector calculations should be employed whenever possible. However, if approximate scalar calculations are used, we recommend to avoid geometries involving phase angles equal or close to 0 deg and 90 deg, where the errors are especially significant. We propose a theoretical explanation of the large vector/scalar differences in the case of Rayleigh scattering. According to this explanation, the differences are caused by the particular structure of the Rayleigh scattering matrix and come from lower-order (except first-order) light scattering paths involving right scattering angles and right-angle rotations of the scattering plane.

  2. Factors Affecting Zebra Mussel Kill by the Bacterium Pseudomonas fluorescens

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Daniel P. Molloy

    2004-02-24

    The specific purpose of this research project was to identify factors that affect zebra mussel kill by the bacterium Pseudomonas fluorescens. Test results obtained during this three-year project identified the following key variables as affecting mussel kill: treatment concentration, treatment duration, mussel siphoning activity, dissolved oxygen concentration, water temperature, and naturally suspended particle load. Using this latter information, the project culminated in a series of pipe tests which achieved high mussel kill inside power plants under once-through conditions using service water in artificial pipes.

  3. Psychological Factor Affecting English Speaking Performance for the English Learners in Indonesia

    ERIC Educational Resources Information Center

    Haidara, Youssouf

    2016-01-01

    In every learning situation or environment, human psychology plays a significant role. English speaking is a language skill that is highly affected by human psychology. This research aimed at describing the psychological factor that affects negatively the English speaking performance for the English learners in Indonesia. A descriptive qualitative…

  4. The Key Factors Affecting Students' Individual Interest in School Science Lessons

    ERIC Educational Resources Information Center

    Cheung, Derek

    2018-01-01

    Individual interest in school science lessons can be defined as a relatively stable and enduring personal emotion comprising affective and behavioural reactions to events in the regular science lessons at school. Little research has compared the importance of different factors affecting students' individual interest in school science lessons. The…

  5. Affective changes during the postpartum period: Influences of genetic and experiential factors.

    PubMed

    Agrati, Daniella; Lonstein, Joseph S

    2016-01-01

    This article is part of a Special Issue "Parental Care". The postpartum period involves some truly transformational changes in females' socioemotional behaviors. For most female laboratory rodents and women, these changes include an improvement in their affective state, which has positive consequences for their ability to sensitively care for their offspring. There is heterogeneity among females in the likelihood of this positive affective change, though, and some women experience elevated anxiety or depression (or in rodents anxiety- or depression-related behaviors) after giving birth. We aim to contribute to the understanding of this heterogeneity in maternal affectivity by reviewing selected components of the scientific literatures on laboratory rodents and humans examining how mothers' physical contact with her infants, genetics, history of anxiety and depression and early-life and recent-life experiences contribute to individual differences in postpartum affective states. These studies together indicate that multiple biological and environmental factors beyond female maternal state shape affective responses during the postpartum period, and probably do so in an interactive manner. Furthermore, the similar capacity of some of these factors to modulate anxiety and depression in human and rodent mothers suggests cross-species conservation of mechanisms regulating postpartum affectivity. Copyright © 2015 Elsevier Inc. All rights reserved.

  6. Factors Affecting Soil Microbial Community Structure in Tomato Cropping Systems

    USDA-ARS?s Scientific Manuscript database

    Soil and rhizosphere microbial communities in agroecosystems may be affected by soil, climate, plant species, and management. We identified some of the most important factors controlling microbial biomass and community structure in an agroecosystem utilizing tomato plants with the following nine tre...

  7. Quantitative impact of aerosols on numerical weather prediction. Part II: Impacts to IR radiance assimilation

    NASA Astrophysics Data System (ADS)

    Marquis, J. W.; Campbell, J. R.; Oyola, M. I.; Ruston, B. C.; Zhang, J.

    2017-12-01

    This is part II of a two-part series examining the impacts of aerosol particles on weather forecasts. In this study, the aerosol indirect effects on weather forecasts are explored by examining the temperature and moisture analysis associated with assimilating dust contaminated hyperspectral infrared radiances. The dust induced temperature and moisture biases are quantified for different aerosol vertical distribution and loading scenarios. The overall impacts of dust contamination on temperature and moisture forecasts are quantified over the west coast of Africa, with the assistance of aerosol retrievals from AERONET, MPL, and CALIOP. At last, methods for improving hyperspectral infrared data assimilation in dust contaminated regions are proposed.

  8. Evaluating the Addition of a Dinoflagellate Phytoplankton Functional Type Using Radiance Anomalies for Monterey Bay, CA

    NASA Astrophysics Data System (ADS)

    Houskeeper, H. F.; Kudela, R. M.

    2016-12-01

    Ocean color sensors have enabled daily, global monitoring of phytoplankton productivity in the world's oceans. However, to observe key structures such as food webs, or to identify regime shifts of dominant species, tools capable of distinguishing between phytoplankton functional types using satellite remote sensing reflectance are necessary. One such tool developed by Alvain et al. (2005), PHYSAT, successfully linked four phytoplankton functional types to chlorophyll-normalized remote sensing spectra, or radiance anomalies, in case-1 waters. Yet this tool was unable to characterize dinoflagellates because of their ubiquitous background presence in the open ocean. We employ a radiance anomaly technique based on PHYSAT to target phytoplankton functional types in Monterey Bay, a region where dinoflagellate populations are larger and more variable than in open ocean waters, and thus where they may be viable targets for satellite remote sensing characterization. We compare with an existing Santa Cruz Wharf photo-pigment time series spanning from 2006 to the present to regionally ground-truth the method's predictions, and we assess its accuracy in characterizing dinoflagellates, a phytoplankton group that impacts the region's fish stocks and water quality. For example, an increase in dinoflagellate abundance beginning in 2005 led to declines in commercially important fish stocks that persisted throughout the following year. Certain species of dinoflagellates in Monterey Bay are also responsible for some of the harmful algal bloom events that negatively impact the shellfish industry. Moving toward better tools to characterize phytoplankton blooms is important for understanding ecosystem shifts, as well as protecting human health in the surrounding areas.

  9. Factors affecting the reproductive success of dominant male meerkats.

    PubMed

    Spong, Göran F; Hodge, Sarah J; Young, Andrew J; Clutton-Brock, Tim H

    2008-05-01

    Identifying traits that affect the reproductive success of individuals is fundamental for our understanding of evolutionary processes. In cooperative breeders, a dominant male typically restricts mating access to the dominant female for extended periods, resulting in pronounced variation in reproductive success among males. This may result in strong selection for traits that increase the likelihood of dominance acquisition, dominance retention and reproductive rates while dominant. However, despite considerable research on reproductive skew, few studies have explored the factors that influence these three processes among males in cooperative species. Here we use genetic, behavioural and demographic data to investigate the factors affecting reproductive success in dominant male meerkats (Suricata suricatta). Our data show that dominant males sire the majority of all offspring surviving to 1 year. A male's likelihood of becoming dominant is strongly influenced by age, but not by weight. Tenure length and reproductive rate, both important components of dominant male reproductive success, are largely affected by group size and composition, rather than individual traits. Dominant males in large groups have longer tenures, but after this effect is controlled, male tenure length also correlates negatively to the number of adult females in the group. Male reproductive rate also declines as the number of intra- and extra-group competitors increases. As the time spent in the dominant position and reproductive rate while dominant explain > 80% of the total variance in reproductive success, group composition thus has major implications for male reproductive success.

  10. Factors affecting the employability in people with epilepsy.

    PubMed

    Wo, Monica Chen Mun; Lim, Kheng Seang; Choo, Wan Yuen; Tan, Chong Tin

    2016-12-01

    People with epilepsy (PWE) are negatively prejudiced in their ability to work. This study aimed to examine demographic, clinical and psychological factors associated with employability in PWE. This study recruited epilepsy patients from a neurology clinic in Malaysia. Employability was measured using employment ratio, with a ratio ≥90% (ER90) classified as high employability. Basic demographic data such as age, gender, marital status, religion, education level and household income was collected. Clinical measures consisted of age of seizure onset, seizure frequency, type of epilepsy, aura, polytherapy, nocturnal seizures and seizure control. Psychological measures included Work Self-Determination Index (WSDI), Rosenberg Self-Esteem Scale (SES), and Multidimensional Scale of Perceived Social Support (MSPSS). Of 146 PWE, 64.4% had high employability. The participants were predominantly female (52%), Chinese (50.7%), single (50%), having tertiary education (55.5%) and focal epilepsy (72.6%). Clinically, only type of epilepsy was significantly correlated to employability of PWE. Employability of PWE was associated with ability to work (indicated by education level, work performance affected by seizures, ability to travel independently and ability to cope with stress at work) and family overprotection. The high employability group was found to have lower self-perceived stigma (ESS), higher self-determined motivation (WSDI), self-esteem (SES) and perceived social support (MSPSS), than the low employability group. Logistic regression analysis showed that tertiary education level (AOR 3.42, CI: 1.46-8.00), higher self-determination (WSDI, AOR 1.09, CI: 1.012-1.17), lower family overprotection (AOR 0.76, CI: 0.61-0.95), and generalised epilepsy (AOR 4.17, CI: 1.37-12.70) were significant predictors for higher employability in PWE. Ability to work (education level), clinical factor (type of epilepsy) and psychological factor (self-determined motivation and family

  11. Personal Factors that Affect the Satisfaction of Female Patients Undergoing Esthetic Suture after Typical Thyroidectomy.

    PubMed

    Kim, Hyo Young; Kim, Jung Won; Park, Jin Hyung; Kim, Jung Hun; Han, Yea Sik

    2013-07-01

    In esthetic surgery, understanding the factors that influence patient satisfaction is important for successful practice. We hypothesize that the factors that influence patient satisfaction include not only aesthetic and functional outcomes, but also personal factors such as the level of familiarity with factors affecting wound healing and expectations regarding aesthetic outcome. One hundred patients who underwent esthetic closure after thyroidectomy were included in this study. In order to evaluate the individual characteristics of the patients, a preoperative survey was administered to the patients. We estimated the patient satisfaction six months postoperatively and assessed the aesthetic and functional outcomes using the Patient and Observer Scar Assessment Scale. According to the results of correlation analysis, level of familiarity with wound healing factors had a positive correlation with satisfaction. High expectations, pain, itching, and high observer scale score had negative correlations with satisfaction. The factors that were correlated with satisfaction were included in the multiple regression analysis. Level of familiarity with wound healing factors was found to have a positive relationship with satisfaction, while itching and observer scale were found to have a negative relationship with satisfaction. After excluding 10 patients who had hypertrophic scars, only level of familiarity with wound healing factors and expectations affected satisfaction. The level of familiarity with factors affecting wound healing and expectations were found to independently affect satisfaction. Improving patients' level of familiarity with wound healing factors and reducing their expectations by providing suitable preoperative education has the potential to improve patient satisfaction.

  12. Arsenic in Drinking Water in Bangladesh: Factors Affecting Child Health

    PubMed Central

    Aziz, Sonia N.; Aziz, Khwaja M. S.; Boyle, Kevin J.

    2014-01-01

    The focus of this paper is to present an empirical model of factors affecting child health by observing actions households take to avoid exposure to arsenic in drinking water. Millions of Bangladeshis face multiple health hazards from high levels of arsenic in drinking water. Safe water sources are either expensive or difficult to access, affecting people’s individuals’ time available for work and ultimately affecting the health of household members. Since children are particularly susceptible and live with parents who are primary decision makers for sustenance, parental actions linking child health outcomes is used in the empirical model. Empirical results suggest that child health is significantly affected by the age and gender of the household water procurer. Adults with a high degree of concern for children’s health risk from arsenic contamination, and who actively mitigate their arsenic contaminated water have a positive effect on child health. PMID:24982854

  13. Factors affecting physical therapists’ job satisfaction: questionnaire survey targeting first-year physical therapists

    PubMed Central

    Kota, Munetsugu; Kudo, Hiroyuki; Okita, Kazuhiko

    2018-01-01

    [Purpose] The survey aimed to clarify the factors that affect physiotherapists’ job satisfaction. [Subjects and Methods] To examine factors affecting physical therapists’ job satisfaction using a cross-sectional study with a questionnaire survey. Subjects were 193 first-year physical therapists who participated in a newcomer orientation at Hiroshima Prefectural Physical Therapy Association. The questionnaire comprised items concerning physical therapists’ satisfaction with their work, motives for becoming physical therapists, education in school, internships, the workplace, and comfort in the workplace. [Results] Subjects were divided into two groups according to their satisfaction with their occupation. The “high satisfaction” group included 157 subjects, and the group “low satisfaction” group included 36 subjects. Using logistic regression analysis, items concerning comfort in the workplace, motives for becoming physical therapists, and learning in school were analysed. [Conclusion] Factors affecting physical therapists’ job satisfaction were primarily influenced by previous experience and working conditions. PMID:29706706

  14. Factors affecting physical therapists' job satisfaction: questionnaire survey targeting first-year physical therapists.

    PubMed

    Kota, Munetsugu; Kudo, Hiroyuki; Okita, Kazuhiko

    2018-04-01

    [Purpose] The survey aimed to clarify the factors that affect physiotherapists' job satisfaction. [Subjects and Methods] To examine factors affecting physical therapists' job satisfaction using a cross-sectional study with a questionnaire survey. Subjects were 193 first-year physical therapists who participated in a newcomer orientation at Hiroshima Prefectural Physical Therapy Association. The questionnaire comprised items concerning physical therapists' satisfaction with their work, motives for becoming physical therapists, education in school, internships, the workplace, and comfort in the workplace. [Results] Subjects were divided into two groups according to their satisfaction with their occupation. The "high satisfaction" group included 157 subjects, and the group "low satisfaction" group included 36 subjects. Using logistic regression analysis, items concerning comfort in the workplace, motives for becoming physical therapists, and learning in school were analysed. [Conclusion] Factors affecting physical therapists' job satisfaction were primarily influenced by previous experience and working conditions.

  15. Factors affecting wood energy consumption by U.S. households

    Treesearch

    Nianfu Song; Francisco X. Aguilar; Stephen R. Shifley; Michael E. Goerndt

    2012-01-01

    About 23% of energy derived from woody sources in the U.S. was consumed by households, of which 70% was used by households in rural areas in 2005. We investigated factors affecting household-level wood energy consumption in the four continental U.S. regions using data from the U.S. Residential Energy Consumption Survey. To account for a large number of zero...

  16. The main factor affecting the competitiveness of Contractor Company

    NASA Astrophysics Data System (ADS)

    Nurisra; Malahayati, Nurul; Mahmuddin

    2018-05-01

    Contractor companies must have the competitive advantage to compete in maintaining the survival of the company. Problems arise because quite a lot of advantages can be used and these advantages must be used appropriately to produce competitiveness for the company to continue to compete and to win the competition. This study aims to determine the main factors affecting the competitiveness of medium-class contractors in Banda Aceh. Data collection was obtained through questionnaires distributed to 31 middle-class contractors in Banda Aceh. Data processing and analysis is done by using descriptive analysis. Based on the result of descriptive analysis, it can be concluded that the most important competitiveness factor with a mean score value 4.52 is the relationship, and the factor that has the highest mean score value is the relationship with the government of 4.97, while the result of the ranking analysis is obtained 25 factor that is critical to the competitiveness of medium-class contractors in Banda Aceh.

  17. Simultaneous determination of aerosol optical thickness and water-leaving radiance from multispectral measurements in coastal waters

    NASA Astrophysics Data System (ADS)

    Shi, Chong; Nakajima, Teruyuki

    2018-03-01

    Retrieval of aerosol optical properties and water-leaving radiance over ocean is challenging since the latter mostly accounts for ˜ 10 % of the satellite-observed signal and can be easily influenced by the atmospheric scattering. Such an effort would be more difficult in turbid coastal waters due to the existence of optically complex oceanic substances or high aerosol loading. In an effort to solve such problems, we present an optimization approach for the simultaneous determination of aerosol optical thickness (AOT) and normalized water-leaving radiance (nLw) from multispectral satellite measurements. In this algorithm, a coupled atmosphere-ocean radiative transfer model combined with a comprehensive bio-optical oceanic module is used to jointly simulate the satellite-observed reflectance at the top of atmosphere and water-leaving radiance just above the ocean surface. Then, an optimal estimation method is adopted to retrieve AOT and nLw iteratively. The algorithm is validated using Aerosol Robotic Network - Ocean Color (AERONET-OC) products selected from eight OC sites distributed over different waters, consisting of observations that covered glint and non-glint conditions from the Moderate Resolution Imaging Spectroradiometer (MODIS) instrument. Results show a good consistency between retrieved and in situ measurements at each site. It is demonstrated that more accurate AOTs are determined based on the simultaneous retrieval method, particularly in shorter wavelengths and sunglint conditions, where the averaged percentage difference (APD) of retrieved AOT is generally reduced by approximate 10 % in visible bands compared with those derived from the standard atmospheric correction (AC) scheme, since all the spectral measurements can be used jointly to increase the information content in the inversion of AOT, and the wind speed is also simultaneously retrieved to compensate the specular reflectance error estimated from the rough ocean surface model. For the

  18. Factors Affecting the Formation of Food Preferences in Preschool Children.

    ERIC Educational Resources Information Center

    Alles-White, Monica L.; Welch, Patricia

    1985-01-01

    Identifies and discusses factors that affect the development of food preferences in preschool children, including familiarity, age, parents, peers, teachers, and programs designed to influence food habits. Makes recommendations to preschool and day care programs for creating an atmosphere conducive to trying new foods. (Author/DST)

  19. Risk factors for injuries in landslide- and flood-affected populations in Uganda.

    PubMed

    Agrawal, Shreya; Gopalakrishnan, Tisha; Gorokhovich, Yuri; Doocy, Shannon

    2013-08-01

    The frequency of occurrence of natural disasters has increased over the past several decades, which necessitates a better understanding of human vulnerability, particularly in low-resource settings. This paper assesses risk factors for injury in the March 2010 floods and landslides in Eastern Uganda, and compares the effects of location, injury type, and severity. A stratified cluster survey of the disaster-affected populations was conducted five months after onset of the disasters. Probability proportional to size sampling was used to sample 800 households, including 400 affected by floods in Butaleja District and 400 affected by landslides in Bududa District. Flood- and landslide-affected populations were surveyed in July 2010 using a stratified cluster design. The odds of injury were 65% higher in the flood-affected groups than the landslide-affected groups in a logistic regression (OR = 0.35; 95% CI, 0.24-0.52; P < .001). The injury rate was greater in individuals under 42 years of age, and location of injury was a contributing factor. More people were injured in the flood-affected population as compared with the landslide-affected population, and injuries were more severe. This study illustrates differences between populations injured by flood and landslide disasters that occurred simultaneously in Eastern Uganda in 2010. In areas where landslides are prone to occur due to massive rainfalls or floods, preventative measures, such as early warning systems and evacuation, are more likely to increase the likelihood of people surviving, while for areas with massive floods, immediate and effective medical attention can save lives and improve injury outcomes.

  20. Factors affecting smoking in schizophrenia.

    PubMed

    Beratis, S; Katrivanou, A; Gourzis, P

    2001-01-01

    There is an increased frequency of smoking among patients with schizophrenia. However, it is unknown whether the smoking behavior of the patients is similar in all schizophrenia subtypes, as well as which is the relationship between smoking initiation and disease onset. Four hundred six patients with DSM-IV schizophrenia were interviewed to determine the smoking status in relationship to gender and schizophrenic subtype, and to other factors that could affect or be affected by smoking. The frequency of smoking among patients (58%) was significantly greater than in subjects from the general population (42%) (P =.000005). Male patients smoked significantly more frequently (70%) than the corresponding control subjects (50%) (P =.000006), whereas the difference failed to reach significance between female patients (41%) and control subjects (32%). Among male patients, the number of smokers was significantly greater than in the controls in the paranoid (77%), undifferentiated (72%), and residual (78%) subtypes, whereas there was no significant difference in the disorganized (44%) and catatonic (22%) subtypes. The findings show that the frequency of smoking in schizophrenia patients increases with increasing positive symptoms and decreases with increasing negative symptoms. Male and female smoking patients consumed approximately 10 cigarettes per day more than the corresponding control subjects (P <.000001). In 86% of the patients, smoking initiation occurred before the disease onset. Among patients who smoked, smoking initiation and disease onset occurred at age 18.7 +/- 4.4 and 24.1 +/- 6.1 years, respectively (P <.000001). It appears that smoking in schizophrenia is influenced by gender and subtype. However, the nature of this association remains uncertain because in the vast majority of the patients smoking initiation occurs earlier than the disease onset. Copyright 2001 by W.B. Saunders Company

  1. Companion of choice at birth: factors affecting implementation.

    PubMed

    Kabakian-Khasholian, Tamar; Portela, Anayda

    2017-08-31

    Two recent recommendations made by the World Health Organization confirm the benefits of companion of choice at birth on labour outcomes; however institutional practices and policies do not always support its implementation in different settings around the world. We conducted a review to determine factors that affect implementation of this intervention considering the perspectives and experiences of different stakeholders and other institutional, systemic barriers and facilitators. Forty one published studies were included in this review. Thirty one publications were identified from a 2013 Cochrane review on the effectiveness of companion of choice at birth. We also reviewed 10 qualitative studies conducted alongside the trials or other interventions on labour and birth companionship identified through electronic searches. The SURE (Supporting the Use of Research Evidence) framework was used to guide the thematic analysis of implementation factors. Women and their families expressed appreciation for the continuous presence of a person to provide support during childbirth. Health care providers were concerned about the role of the companion and possible interference with activities in the labour ward. Allocation of resources, organization of care, facility-related constraints and cultural inclinations were identified as implementation barriers. Prior to introducing companion of choice at birth, understanding providers' attitudes and sensitizing them to the evidence is necessary. The commitment of the management of health care facilities is also required to change policies, including allocation of appropriate physical space that respects women's privacy. Implementation research to develop models for different contexts which could be scaled up would be useful, including documentation of factors that affected implementation and how they were addressed. Future research should also focus on documenting the costs related to implementation, and on measuring the impact of

  2. The Synergistic Effect of Affective Factors on Student Learning Outcomes

    ERIC Educational Resources Information Center

    Jack, Brady Michael; Lin, Huann-shyang; Yore, Larry D.

    2014-01-01

    This study investigates how affective and self-related factors impact participation in science learning and environmental awareness and responsibility. Using PISA 2006 datasets from Taiwan and Canada having similar level of science competency, the model for this study verifies and expands an earlier model by examining the relationships among…

  3. Factors Affecting Educational Innovation with in Class Electronic Response Systems

    ERIC Educational Resources Information Center

    Freeman, Mark; Bell, Amani; Comerton-Forde, Carole; Pickering, Joanne; Blayney, Paul

    2007-01-01

    This paper reports the use of Rogers' diffusion of innovation perspective to understand the factors affecting educational innovation decisions, specifically in regard to in class electronic response systems. Despite decreasing costs and four decades of research showing strong student support, academic adoption is limited. Using data collected from…

  4. Scrutinizing the Factors Affecting Fluency of English among Arab Learners

    ERIC Educational Resources Information Center

    Al Ghazali, Fawzi

    2017-01-01

    This research study investigates the cognitive, psychological and personal factors affecting the accuracy and fluency of English language usage among Arab learners. Early research led by Chomsky (1965) and Krashen (1981) suggested that an individual's Language Acquisition Device once triggered at the appropriate time and supported with adequate…

  5. Factors Affecting the Acceptability of Microforms as a Reading Medium.

    ERIC Educational Resources Information Center

    Spencer, Herbert; Reynolds, Linda

    Based on visits to representative microform users and an extensive survey of relevant literature, a study was undertaken to assess the relative importance of factors affecting the acceptability of microforms as reading mediums. The following variables were considered: (1) microform characteristics; (2) equipment design; (3) work station design;…

  6. Environmental factors affecting understory diversity in second-growth deciduous forests

    Treesearch

    Cynthia D. Huebner; J.C. Randolph; G.R. Parker

    1995-01-01

    The purpose of this study was to determine the most important nonanthropogenic factors affecting understory (herbs, shrubs and low-growing vines) diversity in forested landscapes of southern Indiana. Fourteen environmental variables were measured for 46 sites. Multiple regression analysis showed significant positive correlation between understory diversity and tree...

  7. Factors Affecting School Choice: What Do Malaysian Chinese Parents Want?

    ERIC Educational Resources Information Center

    Siah, Poh Chua; Christina Ong, Sook Beng; Tan, Swee Mee; Sim, Chzia Poaw; Xian Thoo, Raphael Yi

    2018-01-01

    Aiming to explore factors affecting Malaysian Chinese parents in sending their children to either national secondary schools or Chinese independent schools, 494 parents were surveyed using a questionnaire. Results showed that parents who sent their children to Chinese independent schools have different priorities compared to those who sent theirs…

  8. Risk factors affecting human traumatic tympanic membrane perforation regeneration therapy using fibroblast growth factor-2.

    PubMed

    Lou, Zhengcai; Yang, Jian; Tang, Yongmei; Xiao, Jian

    2015-01-01

    The use of growth factors to achieve closure of human traumatic tympanic membrane perforations (TMPs) has recently been demonstrated. However, pretreatment factors affecting healing outcomes have seldom been discussed. The objective of this study was to evaluate pretreatment factors contributing to the success or failure of healing of TMPs using fibroblast growth factor-2 (FGF-2). A retrospective cohort study of 99 patients (43 males, 56 females) with traumatic TMPs who were observed for at least 6 months after FGF-2 treatment between March 2011 and December 2012. Eleven factors considered likely to affect the outcome of perforation closure were evaluated statistically using univariate and multivariate logistic regression analysis. Each traumatic TMP was treated by direct application of FGF-2. Complete closure versus failure to close. In total, 99 patients were analyzed. The total closure rate was 92/99 (92.9%) at 6 months; the mean closure time was 10.59 ±  6.81 days. The closure rate did not significantly differ between perforations with or without inverted edges (100.0% vs. 91.4%, p = 0.087), among different size groups (p = 0.768), or among different periods of exposure to injury (p = 0.051). However, the closure rate was significantly different between the high- and low-dose FGF-2 groups (85.0% vs. 98.3%, p = 0.010) and between perforations where the umbo or malleus was or was not involved in perforation (85.4% vs. 98.3%, p = 0.012). Additionally, univariate logistic regression analysis tests showed that it was difficult to achieve healing of these perforations with a history of chronic otitis media or residual TM calcification (p = 0.006), the umbo or malleus was involved in perforation (p = 0.038), and with a high dose of FGF-2 (p = 0.035) compared with control groups. Multivariate logistic regression analysis showed that only a history of chronic otitis media and residual TM calcification and perforation close to the

  9. Factors affecting alkali jarosite precipitation

    NASA Astrophysics Data System (ADS)

    Dutrizac, J. E.

    1983-12-01

    Several factors affecting the precipitation of the alkali jarosites (sodium jarosite, potassium jarosite, rubidium jarosite, and ammonium jarosite) have been studied systematically using sodium jarosite as the model. The pH of the reacting solution exercises a major influence on the amount of jarosite formed, but has little effect on the composition of the washed product. Higher temperatures significantly increase the yield and slightly raise the alkali content of the jarosites. The yield and alkali content both increase greatly with the alkali concentration to about twice the stoichiometric requirement but, thereafter, remain nearly constant. At 97 °C, the amount of product increases with longer retention times to about 15 hours, but more prolonged reaction times are without significant effect on the amount or composition of the jarosite. Factors such as the presence of seed or ionic strength have little effect on the yield or jarosite composition. The amount of precipitate augments directly as the iron concentration of the solution increases, but the product composition is nearly independent of this variable. A significant degree of agitation is necessary to suspend the product and to prevent the jarosite from coating the apparatus with correspondingly small yields. Once the product is adequately suspended, however, further agitation is without significant effect. The partitioning of alkali ions during jarosite precipitation was ascertained for K:Na, Na:NH4, K:NH4, and K:Rb. Potassium jarosite is the most stable of the alkali jarosites and the stability falls systematically for lighter or heavier congeners; ammonium jarosite is slightly more stable than the sodium analogue. Complete solid solubility among the various alkali jarosite-type compounds was established.

  10. [Phosphorus availability in cropland soils of China and related affecting factors].

    PubMed

    Wang, Yong-Zhuang; Chen, Xin; Shi, Yi

    2013-01-01

    Soil phosphorus (P) availability directly determines cropland productivity. Based on the long-term fertilization experiments in different climatic zones of China, this paper summarized the P content, its availability, and the factors affecting the P transformation in China cropland soils. The total and available P contents in different types of China cropland soils were 0.31-1.72 g x kg(-1) and 0.1-228.8 mg x kg(-1), respectively. Soil parent material, soil physical and chemical prosperities, and fertilization practices were the main factors affecting the soil P availability. It was suggested that more attentions should be paid on the mixed application of organic manure and chemical fertilizers to improve the P availability of cropland soils and on the potential environmental impacts of this fertilization.

  11. Factors affecting workplace bullying and lateral violence among clinical nurses in Korea: descriptive study.

    PubMed

    Oh, Hyunjin; Uhm, Dong Choon; Yoon, Young Joo

    2016-04-01

    Workplace bullying and lateral violence are serious issues affecting the work life of hospital nurses. The purpose of this study was to identify the selected individual and institutional characteristics for workplace bullying and lateral violence using a conceptual framework. A descriptive survey design was used. A convenience sample of 255 nurses in tertiary hospitals, who had a minimum of 6 months clinical experience, completed the survey. Regression analysis was used to determine factors significantly associated with workplace bullying and lateral violence. The Negative Acts Questionnaire-Revised and the Lateral Violence scale were used to measure workplace bullying and lateral violence. A negative affect, individualism and working in hospital specialty units predicted workplace bullying. Individualism, a negative affect, affiliated hospital and working hours predicted verbal abuse whereas the place of employment was significantly associated with lateral violence. The results of this study identified factors that are associated with bullying and violence but did not fully support the conceptual framework. The individual characteristic negative affect was significantly associated with most types of workplace bullying and lateral violence bully whereas the place of employment was an important factor in lateral violence. Nurse managers need to be aware that both individual and institutional factors may impact levels of workplace bullying and lateral violence in their hospitals and need to prepare specific strategies to address these multiple factors. © 2015 John Wiley & Sons Ltd.

  12. Factors affecting length of stay in teaching hospitals of a middle-income country

    PubMed Central

    Khosravizadeh, Omid; Vatankhah, Soudabeh; Bastani, Peivand; Kalhor, Rohollah; Alirezaei, Samira; Doosty, Farzane

    2016-01-01

    Introduction The length of stay (LOS) in hospitals is a widely used and important criteria for evaluating hospital performance. The aim of this study was to determine factors affecting LOS in teaching hospitals of Qazvin Providence. Methods In this cross-sectional study, patients’ health records were randomly selected from archives in teaching hospitals of Qazvin in 2013. Data were collected through a data entry form and were analyzed using Kolmogorov–Smirnov, Kruskal–Wallis, and Mann–Whitney U tests at the significant level of 0.05. Results The mean of hospital LOS was 5.45 ± 6.14 days. Age, employment, marital status, history of previous admission, patient condition at discharge, method of payment, and type of treatment had an impact on LOS (p<0.05). Other factors, including gender, place of residence, and type of admission, did not affect LOS. Conclusion Because hospitals consume a perceptible part of resources in a health system, controlled and optimized use of its resources help to save a lot. Therefore, this study showed many clinical and nonclinical factors affect LOS in evaluating these factors, which may reduce inappropriate hospital stays and decrease costs. PMID:27957301

  13. Analysis of usability factors affecting purchase intention in online e-commerce sites

    NASA Astrophysics Data System (ADS)

    Perdana, R. A.; Suzianti, A.

    2017-03-01

    The growing number of internet users plays a significant role in the emergence of a variety of online e-commerce sites to meet the needs of Indonesians. However, there are still some problems faced by the users in using e-commerce sites. Therefore, a research related to user experience on their purchase intention to foster e-commerce sites is required. This study is conducted to find out the relationship between usability factors on e-commerce users’ purchase intention using a case study by using SEM to analyse the usability of the website. The result of this study shows that credibility, readability and telepresence are usability factors that directly affect purchase intention, while simplicity, consistency and interactivity are usability factors that indirectly affect purchase intention. Therefore, we can conclude that Indonesian consumers are on the Early Majority phase in adopting Company A.

  14. Simultaneous measurement of the dynamic emissivity and the radiance of the shocked Al/LiF interface in the near-infrared wavelength

    NASA Astrophysics Data System (ADS)

    Liu, Shenggang; Li, Jiabo; Li, Jun; Xue, Tao; Tao, Tianjiong; Ma, Heli; Wang, Xiang; Weng, Jidong; Li, Zeren

    2018-04-01

    A novel method based on signal superimposing has been presented to simultaneously measure the dynamic emissivity and the radiance of a shocked sample/window interface in the near-infrared wavelength. In this method, we have used three rectangle laser pulses to illuminate the sample/window interface via an integrating sphere and expect that the reflected laser pulses from the sample/window interface can be superimposed on its thermal radiation at the shocked steady state by time precision synchronization. In the two proving trials, the second laser pulse reflected from the Al/LiF interface has been successfully superimposed on its thermal radiation despite large flyer velocity uncertainty. The dynamic emissivity and the radiance at 1064 nm have been obtained simultaneously from the superimposing signals. The obtained interface temperatures are 1842 ± 82 K and 1666 ± 154 K, respectively, the corresponding release pressures are 65.7 GPa and 62.6 GPa, and the deduced Hugonoit temperatures are consistent with the theoretical calculations. In comparison, the fitting temperatures from the gray body model are 300-500 K higher than our experimental measurement results and the theoretical calculations.

  15. The Internal Structure of Positive and Negative Affect: A Confirmatory Factor Analysis of the PANAS

    ERIC Educational Resources Information Center

    Tuccitto, Daniel E.; Giacobbi, Peter R., Jr.; Leite, Walter L.

    2010-01-01

    This study tested five confirmatory factor analytic (CFA) models of the Positive Affect Negative Affect Schedule (PANAS) to provide validity evidence based on its internal structure. A sample of 223 club sport athletes indicated their emotions during the past week. Results revealed that an orthogonal two-factor CFA model, specifying error…

  16. Factors affecting midwives' confidence in intrapartum care: a phenomenological study.

    PubMed

    Bedwell, Carol; McGowan, Linda; Lavender, Tina

    2015-01-01

    midwives are frequently the lead providers of care for women throughout labour and birth. In order to perform their role effectively and provide women with the choices they require midwives need to be confident in their practice. This study explores factors which may affect midwives' confidence in their practice. hermeneutic phenomenology formed the theoretical basis for the study. Prospective longitudinal data collection was completed using diaries and semi-structured interviews. Twelve midwives providing intrapartum care in a variety of settings were recruited to ensure a variety of experiences in different contexts were captured. the principal factor affecting workplace confidence, both positively and negatively, was the influence of colleagues. Perceived autonomy and a sense of familiarity could also enhance confidence. However, conflict in the workplace was a critical factor in reducing midwives' confidence. Confidence was an important, but fragile, phenomenon to midwives and they used a variety of coping strategies, emotional intelligence and presentation management to maintain it. this is the first study to highlight both the factors influencing midwives' workplace confidence and the strategies midwives employed to maintain their confidence. Confidence is important in maintaining well-being and workplace culture may play a role in explaining the current low morale within the midwifery workforce. This may have implications for women's choices and care. Support, effective leadership and education may help midwives develop and sustain a positive sense of confidence. Copyright © 2014 Elsevier Ltd. All rights reserved.

  17. Specifying the non-specific factors underlying opioid analgesia: Expectancy, attention, and affect

    PubMed Central

    Atlas, Lauren Y.; Wielgosz, Joseph; Whittington, Robert A.; Wager, Tor D.

    2013-01-01

    Rationale Psychological processes such as expectancy, attention, and affect directly influence clinical outcomes. These factors are grouped together as “nonspecific” factors, or placebo effects, in the medical literature, and their individual contributions are rarely considered. The pain-reducing effects of analgesic treatments may reflect changes in these psychological factors, rather than pure drug effects on pain. Furthermore, drug effects may not be isolated by drug vs. placebo comparisons if drugs interact with relevant psychological processes. Objectives To determine whether the analgesic effects of opioid and placebo treatment are mediated by changes in attention, expectancy, or affect. Methods We crossed intravenous administration of a potent opioid analgesic, remifentanil, with information about drug delivery (treatment expectancy, or placebo) using a balanced placebo design. We measured drug and treatment expectancy effects on pain, attention, and responses to emotional images. We also examined interactions with cue-based expectations about noxious stimulation, or stimulus expectancy. Results Pain was additively influenced by treatment expectancy, stimulus expectancy, and drug concentration. Attention performance showed a small but significant interaction between drug and treatment expectancy. Finally, remifentanil enhanced responses to both positive and negative emotional images. Conclusions The pain-relieving effects of opioid drugs are unlikely to be mediated by changes in threat or affective processing. Standard open-label opioid administration influences multiple clinically relevant cognitive and emotional processes. Psychological factors can combine with drug effects to influence multiple outcomes in distinct ways. The influence of specific psychological factors should be considered when developing and testing pharmacological treatments. PMID:24096537

  18. Study on the factors affecting the quality of public bus transportation service in Bali Province using factor analysis

    NASA Astrophysics Data System (ADS)

    Susilawati, M.; Nilakusmawati, D. P. E.

    2017-06-01

    The volume of mobility flows are increasing day by day and the condition of the number of people using private transport modes contribute to traffic congestion. With the limited capacity of the road, one of the alternatives solution to reduce congestion is to optimize the use of public transport. The purposes of this study are to determine the factors that influence user’s satisfaction on the quality of public bus transportation service and determine variables that became identifier on the dominant factor affecting user’s satisfaction. The study was conducted for the public bus transportation between districts in the province of Bali, which is among the eight regencies and one municipality, using a questionnaire as a data collection instrument. Service variables determinant of user’s satisfaction in this study, described in 25 questions, which were analyzed using factor analysis. The results showed there were six factors that explain the satisfaction of users of public transport in Bali, with a total diversity of data that can be parsed by 61.436%. These factors are: Safety and comfort, Responsiveness, Capacity, Tangible, Safety, Reliability. The dominant factor affecting public transport user satisfaction is the safety and comfort, with the most influential variable is feeling concerned about the personal safety of users when on the bus.

  19. Comparison of spectral radiance responsivity calibration techniques used for backscatter ultraviolet satellite instruments

    NASA Astrophysics Data System (ADS)

    Kowalewski, M. G.; Janz, S. J.

    2015-02-01

    Methods of absolute radiometric calibration of backscatter ultraviolet (BUV) satellite instruments are compared as part of an effort to minimize pre-launch calibration uncertainties. An internally illuminated integrating sphere source has been used for the Shuttle Solar BUV, Total Ozone Mapping Spectrometer, Ozone Mapping Instrument, and Global Ozone Monitoring Experiment 2 using standardized procedures traceable to national standards. These sphere-based spectral responsivities agree to within the derived combined standard uncertainty of 1.87% relative to calibrations performed using an external diffuser illuminated by standard irradiance sources, the customary spectral radiance responsivity calibration method for BUV instruments. The combined standard uncertainty for these calibration techniques as implemented at the NASA Goddard Space Flight Center’s Radiometric Calibration and Development Laboratory is shown to less than 2% at 250 nm when using a single traceable calibration standard.

  20. BOREAS Level-4b AVHRR-LAC Ten-Day Composite Images: At-sensor Radiance

    NASA Technical Reports Server (NTRS)

    Cihlar, Josef; Chen, Jing; Nickerson, Jaime; Newcomer, Jeffrey A.; Huang, Feng-Ting; Hall, Forrest G. (Editor)

    2000-01-01

    The BOReal Ecosystem-Atmosphere Study (BOREAS) Staff Science Satellite Data Acquisition Program focused on providing the research teams with the remotely sensed satellite data products they needed to compare and spatially extend point results. Manitoba Remote Sensing Center (MRSC) and BOREAS Information System (BORIS) personnel acquired, processed, and archived data from the Advanced Very High Resolution Radiometer (AVHRR) instruments on the National Oceanic and Atmospheric Administration (NOAA-11) and -14 satellites. The AVHRR data were acquired by CCRS and were provided to BORIS for use by BOREAS researchers. These AVHRR level-4b data are gridded, 10-day composites of at-sensor radiance values produced from sets of single-day images. Temporally, the 10- day compositing periods begin 11-Apr-1994 and end 10-Sep-1994. Spatially, the data cover the entire BOREAS region. The data are stored in binary image format files.

  1. A study of factors affecting the adoption of server virtualization technology

    NASA Astrophysics Data System (ADS)

    Lu, Hsin-Ke; Lin, Peng-Chun; Chiang, Chang-Heng; Cho, Chien-An

    2018-04-01

    It has become a trend that worldwide enterprises and organizations apply new technologies to improve their operations; besides, it has higher cost and less flexibility to construct and manage traditional servers, therefore the current mainstream is to use server virtualization technology. However, from these new technology organizations will not necessarily get the expected benefits because each one has its own level of organizational complexity and abilities to accept changes. The researcher investigated key factors affecting the adoption of virtualization technology through two phases. In phase I, the researcher reviewed literature and then applied the dimensions of "Information Systems Success Model" (ISSM) to generalize the factors affecting the adoption of virtualization technology to be the preliminary theoretical framework and develop a questionnaire; in phase II, a three-round Delphi Method was used to integrate the opinions of experts from related fields which were then gradually converged in order to obtain a stable and objective questionnaire of key factors so that these results were expected to provide references for organizations' adoption of server virtualization technology and future studies.

  2. Factors Affecting Environmental Knowledge and Attitudes among Lebanese College Students

    ERIC Educational Resources Information Center

    Oweini, Ahmad; Houri, Ahmad

    2006-01-01

    This exploratory study aimed at assessing the variables that would positively affect the knowledge and attitude of a group of Lebanese college students regarding the environment, namely such factors as gender, age, previous hiking experience and living abroad. A purposeful sample of students attending the Lebanese American University, was asked to…

  3. Factors Affecting Performance of Undergraduate Students in Construction Related Disciplines

    ERIC Educational Resources Information Center

    Olatunji, Samuel Olusola; Aghimien, Douglas Omoregie; Oke, Ayodeji Emmanuel; Olushola, Emmanuel

    2016-01-01

    Academic performance of students in Nigerian institutions has been of much concern to all and sundry hence the need to assess the factors affecting performance of undergraduate students in construction related discipline in Nigeria. A survey design was employed with questionnaires administered on students in the department of Quantity Surveying,…

  4. Radiance, polarization, and ellipticity of the radiation in the earth's atmosphere

    NASA Technical Reports Server (NTRS)

    Hitzfelder, S. J.; Plass, G. N.; Kattawar, G. W.

    1976-01-01

    The complete radiation field including polarization is calculated for a model of the real atmosphere by the matrix operator method. The radiance, direction and amount of polarization, and ellipticity are obtained at the top and bottom of the atmosphere for three values of the surface albedo (0; 0.15 0.90) and five solar zenith angles. Scattering and absorption by molecules (including ozone) and by aerosols are taken into account together with the variation of the number density of these substances with height. All results are calculated for both a normal aerosol number and a distribution which is one-third of the normal amount at all heights. The calculated values show general qualitative agreement with the available experimental measurements. The position of the neutral points of the polarization in the principal plane is a sensitive indicator of the characteristics of the aerosol particles in the atmosphere, since it depends on the sign and value of the single scattered polarization for scattering angles around 20 deg and 160 deg for transmitted and reflected photons respectively.

  5. Factors affecting the implementation of childhood vaccination communication strategies in Nigeria: a qualitative study.

    PubMed

    Oku, Afiong; Oyo-Ita, Angela; Glenton, Claire; Fretheim, Atle; Eteng, Glory; Ames, Heather; Muloliwa, Artur; Kaufman, Jessica; Hill, Sophie; Cliff, Julie; Cartier, Yuri; Bosch-Capblanch, Xavier; Rada, Gabriel; Lewin, Simon

    2017-02-15

    The role of health communication in vaccination programmes cannot be overemphasized: it has contributed significantly to creating and sustaining demand for vaccination services and improving vaccination coverage. In Nigeria, numerous communication approaches have been deployed but these interventions are not without challenges. We therefore aimed to explore factors affecting the delivery of vaccination communication in Nigeria. We used a qualitative approach and conducted the study in two states: Bauchi and Cross River States in northern and southern Nigeria respectively. We identified factors affecting the implementation of communication interventions through interviews with relevant stakeholders involved in vaccination communication in the health services. We also reviewed relevant documents. Data generated were transcribed verbatim and analysed using thematic analysis. We used the SURE framework to organise the identified factors (barriers and facilitators) affecting vaccination communication delivery. We then grouped these into health systems and community level factors. Some of the commonly reported health system barriers amongst stakeholders interviewed included: funding constraints, human resource factors (health worker shortages, training deficiencies, poor attitude of health workers and vaccination teams), inadequate infrastructure and equipment and weak political will. Community level factors included the attitudes of community stakeholders and of parents and caregivers. We also identified factors that appeared to facilitate communication activities. These included political support, engagement of traditional and religious institutions and the use of organised communication committees. Communication activities are a crucial element of immunization programmes. It is therefore important for policy makers and programme managers to understand the barriers and facilitators affecting the delivery of vaccination communication so as to be able to implement

  6. Factors affecting early and long-term outcomes after completion pneumonectomy.

    PubMed

    Chataigner, Olivier; Fadel, Elie; Yildizeli, Bedrettin; Achir, Abdallah; Mussot, Sacha; Fabre, Dominique; Mercier, Olaf; Dartevelle, Philippe G

    2008-05-01

    To identify factors that affect operative mortality and morbidity and long-term survival after completion pneumonectomy. We retrospectively reviewed the charts of consecutive patients who underwent completion pneumonectomy at our cardiothoracic surgery department from January 1996 to December 2005. We identified 69 patients, who accounted for 17.8% of all pneumonectomies during the study period; 22 had benign disease and 47 malignant disease (second primary lung cancer, n=19; local recurrence, n=17; or metastasis, n=11). There were 50 males and 19 females with a mean age of 60 years (range, 29-80 years). Postoperative mortality was 12% and postoperative morbidity 41%. Factors associated with postoperative mortality included obesity (p=0.005), coronary artery disease (p=0.03), removal of the right lung (p=0.02), advanced age (p=0.02), and renal failure (p<0.0001). Preoperative renal failure was the only significant risk factor for mortality by multivariate analysis (p=0.036). Bronchopleural fistula developed in seven patients (10%), with risk factors being removal of the right lung (p=0.04) and mechanical stump closure (p=0.03). Overall survival was 65% after 3 years and 46% after 5 years. Long-term survival was not affected by the reason for completion pneumonectomy. Although long-term survival was acceptable, postoperative mortality and morbidity rates remained high, confirming the reputation of completion pneumonectomy as a challenging procedure. Significant comorbidities and removal of the right lung were the main risk factors for postoperative mortality. Improved patient selection and better management of preoperative renal failure may improve the postoperative outcomes of this procedure, which offers a chance for prolonged survival.

  7. Validation of Atmospheric InfraRed Sounder (AIRS) spectral radiances with the Scanning High-resolution Interferometer Sounder (S-HIS) aircraft instrument

    NASA Astrophysics Data System (ADS)

    Tobin, David C.; Revercomb, Henry E.; Moeller, Chris C.; Knuteson, Robert O.; Best, Fred A.; Smith, William L.; van Delst, Paul; LaPorte, Daniel D.; Ellington, Scott D.; Werner, Mark D.; Dedecker, Ralph G.; Garcia, Raymond K.; Ciganovich, Nick N.; Howell, Hugh B.; Dutcher, Steven B.; Taylor, Joe K.

    2004-11-01

    The ability to accurately validate high spectral resolution infrared radiance measurements from space using comparisons with aircraft spectrometer observations has been successfully demonstrated. The demonstration is based on an under-flight of the Atmospheric Infrared Sounder (AIRS) on the NASA Aqua spacecraft by the Scanning High resolution Interferometer Sounder (S-HIS) on the NASA ER-2 high altitude aircraft on 21 November 2002 and resulted in brightness temperature differences approaching 0.1K for most of the spectrum. This paper presents the details of this AIRS/S-HIS validation case and also presents comparisons of Aqua AIRS and Moderate Resolution Imaging Spectroradiometer (MODIS) radiance observations. Aircraft comparisons of this type provide a mechanism for periodically testing the absolute calibration of spacecraft instruments with instrumentation for which the calibration can be carefully maintained on the ground. This capability is especially valuable for assuring the long-term consistency and accuracy of climate observations. It is expected that aircraft flights of the S-HIS and its close cousin the National Polar Orbiting Environmental Satellite System (NPOESS) Atmospheric Sounder Testbed (NAST) will be used to check the long-term stability of the NASA EOS spacecrafts (Terra, Aqua and Aura) and the follow-on complement of operational instruments, including the Cross-track Infrared Sounder (CrIS).

  8. High infrared radiance glass-ceramics obtained from fly ash and titanium slag.

    PubMed

    Wang, Shuming; Liang, Kaiming

    2007-11-01

    A new glass-ceramic was synthesized by crystal growth from a homogenous glass obtained by melting a mixture of fly ash collected from a power plant in Hebei province of China, titanium slag collected from a titanium factory in Sichuan province of China, and MgCO(3) as an additive. According to the measurement results of differential thermal analysis, a thermal treatment of nucleating at 850 degrees C for 2h and crystallizing at 985 degrees C for 1.5h was used to obtain the crystallized glass. X-ray diffraction and scanning electron microscopy measurements showed that the main crystalline phase of this material was iron-ion substituted cordierite, (Mg,Fe)(2)Al(4)Si(5)O(18), which is homogeneously dispersed within the parent glass matrix. The infrared radiance and thermal expansion coefficient of this material have been examined, and the results demonstrate that this glass-ceramic material has potential for application in a wide range of infrared heating and drying materials.

  9. Upwelled spectral radiance distribution in relation to particulate matter in sea water

    NASA Technical Reports Server (NTRS)

    Clark, D. K.; Strong, A. E.; Baker, E. T.

    1980-01-01

    Spectral analysis of water color and concurrent measurements of the relative concentration of various particulate and dissolved constituents within a broad range of water types are necessary to quantify ocean color observations and successfully relate them to various biological and physical processes that can be monitored by remote sensing. Some of the results of a Nimbus-G prelaunch cruise in connection with the Coastal Zone Color Scanner (CZCS) experiment, which was carried out in the Gulf of Mexico in October 1977, are presented and discussed. Based upon a small but diverse sample of near-surface measurements, it appears possible to estimate total suspended particulate matter (SPM) to useful accuracies by forming ratios of the spectral radiances measured at wavelengths falling near the centers of certain CZCS bands, viz., 440 nm:550 nm and 440 nm:520 nm. Furthermore, the analysis suggests a very high degree of covariation between SPM and phytoplankton pigments except for certain well-defined special cases.

  10. HYTHIRM Radiance Modeling and Image Analyses in Support of STS-119, STS-125 and STS-128 Space Shuttle Hypersonic Re-entries

    NASA Technical Reports Server (NTRS)

    Gibson, David M.; Spisz, Thomas S.; Taylor, Jeff C.; Zalameda, Joseph N.; Horvath, Thomas J.; Tomek, Deborah M.; Tietjen, Alan B.; Tack, Steve; Bush, Brett C.

    2010-01-01

    We provide the first geometrically accurate (i.e., 3-D) temperature maps of the entire windward surface of the Space Shuttle during hypersonic reentry. To accomplish this task we began with estimated surface temperatures derived from CFD models at integral high Mach numbers and used them, the Shuttle's surface properties and reasonable estimates of the sensor-to-target geometry to predict the emitted spectral radiance from the surface (in units of W sr-1 m-2 nm-1). These data were converted to sensor counts using properties of the sensor (e.g. aperture, spectral band, and various efficiencies), the expected background, and the atmosphere transmission to inform the optimal settings for the near-infrared and midwave IR cameras on the Cast Glance aircraft. Once these data were collected, calibrated, edited, registered and co-added we formed both 2-D maps of the scene in the above units and 3-D maps of the bottom surface in temperature that could be compared with not only the initial inputs but also thermocouple data from the Shuttle itself. The 3-D temperature mapping process was based on the initial radiance modeling process. Here temperatures were guessed for each node in a well-resolved 3-D framework, a radiance model was produced and compared to the processed imagery, and corrections to the temperature were estimated until the iterative process converged. This process did very well in characterizing the temperature structure of the large asymmetric boundary layer transition the covered much of the starboard bottom surface of STS-119 Discovery. Both internally estimated accuracies and differences with CFD models and thermocouple measurements are at most a few percent. The technique did less well characterizing the temperature structure of the turbulent wedge behind the trip due to limitations in understanding the true sensor resolution. (Note: Those less inclined to read the entire paper are encouraged to read an Executive Summary provided at the end.)

  11. Factors Affecting 25-Hydroxyvitamin D Concentration in Response to Vitamin D Supplementation

    PubMed Central

    Mazahery, Hajar; von Hurst, Pamela R.

    2015-01-01

    Sun exposure is the main source of vitamin D. Due to many lifestyle risk factors vitamin D deficiency/insufficiency is becoming a worldwide health problem. Low 25(OH)D concentration is associated with adverse musculoskeletal and non-musculoskeletal health outcomes. Vitamin D supplementation is currently the best approach to treat deficiency and to maintain adequacy. In response to a given dose of vitamin D, the effect on 25(OH)D concentration differs between individuals, and it is imperative that factors affecting this response be identified. For this review, a comprehensive literature search was conducted to identify those factors and to explore their significance in relation to circulating 25(OH)D response to vitamin D supplementation. The effect of several demographic/biological factors such as baseline 25(OH)D, aging, body mass index(BMI)/body fat percentage, ethnicity, calcium intake, genetics, oestrogen use, dietary fat content and composition, and some diseases and medications has been addressed. Furthermore, strategies employed by researchers or health care providers (type, dose and duration of vitamin D supplementation) and environment (season) are other contributing factors. With the exception of baseline 25(OH)D, BMI/body fat percentage, dose and type of vitamin D, the relative importance of other factors and the mechanisms by which these factors may affect the response remains to be determined. PMID:26121531

  12. Factors Affecting Aerosol Radiative Forcing

    NASA Astrophysics Data System (ADS)

    Wang, Jingxu; Lin, Jintai; Ni, Ruijing

    2016-04-01

    Rapid industrial and economic growth has meant a large amount of aerosols in the atmosphere with strong radiative forcing (RF) upon the climate system. Over parts of the globe, the negative forcing of aerosols has overcompensated for the positive forcing of greenhouse gases. Aerosol RF is determined by emissions and various chemical-transport-radiative processes in the atmosphere, a multi-factor problem whose individual contributors have not been well quantified. In this study, we analyze the major factors affecting RF of secondary inorganic aerosols (SIOAs, including sulfate, nitrate and ammonium), primary organic aerosol (POA), and black carbon (BC). We analyze the RF of aerosols produced by 11 major regions across the globe, including but not limited to East Asia, Southeast Asia, South Asia, North America, and Western Europe. Factors analyzed include population size, per capita gross domestic production (GDP), emission intensity (i.e., emissions per unit GDP), chemical efficiency (i.e., mass per unit emissions) and radiative efficiency (i.e., RF per unit mass). We find that among the 11 regions, East Asia produces the largest emissions and aerosol RF, due to relatively high emission intensity and a tremendous population size. South Asia produce the second largest RF of SIOA and BC and the highest RF of POA, in part due to its highest chemical efficiency among all regions. Although Southeast Asia also has large emissions, its aerosol RF is alleviated by its lowest chemical efficiency. The chemical efficiency and radiative efficiency of BC produced by the Middle East-North Africa are the highest across the regions, whereas its RF is lowered by a small per capita GDP. Both North America and Western Europe have low emission intensity, compensating for the effects on RF of large population sizes and per capita GDP. There has been a momentum to transfer industries to Southeast Asia and South Asia, and such transition is expected to continue in the coming years. The

  13. Factors Affecting Aerosol Radiative Forcing

    NASA Astrophysics Data System (ADS)

    Wang, J.; Lin, J.; Ni, R.

    2016-12-01

    Rapid industrial and economic growth has meant large amount of aerosols in the atmosphere with strong radiative forcing (RF) upon the climate system. Over parts of the globe, the negative forcing of aerosols has overcompensated for the positive forcing of greenhouse gases. Aerosol RF is determined by emissions and various chemical-transport-radiative processes in the atmosphere, a multi-factor problem whose individual contributors have not been well quantified. In this study, we analyze the major factors affecting RF of secondary inorganic aerosols (SIOAs, including sulfate, nitrate and ammonium), primary organic aerosol (POA), and black carbon (BC). We analyze the RFof aerosols produced by 11 major regions across the globe, including but not limited to East Asia, Southeast Asia, South Asia, North America, and Western Europe. Factors analyzed include population size, per capita gross domestic production (GDP), emission intensity (i.e., emissionsper unit GDP), chemical efficiency (i.e., mass per unit emissions) and radiative efficiency (i.e., RF per unit mass). We find that among the 11 regions, East Asia produces the largest emissions and aerosol RF, due to relatively high emission intensity and a tremendous population size.South Asia produce the second largest RF of SIOA and BC and the highest RF of POA, in part due to its highest chemical efficiency among all regions. Although Southeast Asia also has large emissions,its aerosol RF is alleviated by its lowest chemical efficiency.The chemical efficiency and radiative efficiency of BC produced by the Middle East-North Africa are the highest across the regions, whereas its RF is loweredbyasmall per capita GDP.Both North America and Western Europe have low emission intensity, compensating for the effects on RF of large population sizes and per capita GDP. There has been a momentum to transfer industries to Southeast Asia and South Asia, and such transition is expected to continue in the coming years. The resulting

  14. Mothers recovering from cocaine addiction: factors affecting parenting skills.

    PubMed

    Coyer, S M

    2001-01-01

    To identify factors that may influence parenting by mothers who are recovering from cocaine addiction. Exploratory descriptive, with in-depth unstructured interviews. Interviews were conducted in the woman's home or in a treatment center. A convenience sample of 11 women recovering from cocaine addiction who were mothers of children 3 years of age and younger. A content analysis was used to analyze the interview data. Two themes, personal/psychologic factors and environmental/contextual factors, and four subthemes emerged. They identify issues that may affect parenting by mothers being treated for cocaine addiction. Subthemes included low self-esteem, difficulty developing a maternal identity, isolation from friends and family, and chronic life stress. This study provides a better understanding of the sources contributing to vulnerability in the parenting role for mothers recovering from cocaine addiction and will assist nurses in providing care for these mothers and their children.

  15. Factors Affecting the Interest of Israeli Social Work Students in Working with Different Client Groups

    ERIC Educational Resources Information Center

    Krumer-Nevo, Michal; Weiss, Idit

    2006-01-01

    Employing a large-scale sample of 521 BSW students from 4 Israeli schools of social work, this research examines the factors affecting social work students' interest in working with a wide range of client groups. The results suggest that student interest in working with specific client groups is affected by factors related to desire for…

  16. Factors Affecting English Language Teaching and Learning in Higher Education

    ERIC Educational Resources Information Center

    Nguyen, Hong Thi; Warren, Wendy; Fehring, Heather

    2014-01-01

    This paper reports part of a study that aims to explore factors affecting the efficacy of non-major English teaching and learning in Vietnamese higher education through an investigation of classroom practices. Eight non-participant class observations were conducted at HUTECH University, Ho Chi Minh City, Vietnam. The study's findings show that…

  17. The Impact of CLIL on Affective Factors and Vocabulary Learning

    ERIC Educational Resources Information Center

    Heras, Arantxa; Lasagabaster, David

    2015-01-01

    The aim of this article is twofold: to assess the effectiveness of a CLIL (content and language integrated learning) module on affective factors (motivation and self-esteem), and to test the purported blurring effect of CLIL on gender differences in foreign language learning. Forty-six students in their fourth year of compulsory secondary…

  18. The Perspective of Gozitan Teachers on Factors Affecting Students' Achievement

    ERIC Educational Resources Information Center

    Xuereb, Lorna; De Giovanni, Katya Sarah

    2016-01-01

    This study aims at exploring the impact of factors at pupil, teacher and school levels on students? academic achievement. Moreover, the main purpose was that of investigating which one of the three levels is most likely to affect students? educational accomplishment. A questionnaire was administered to 100 Gozitan teachers. Results were analysed…

  19. 77 FR 18862 - Brazil: Competitive Factors Affecting U.S. and Brazilian Agricultural Sales in Selected Third...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-03-28

    ... INTERNATIONAL TRADE COMMISSION [Investigation No. 332-524] Brazil: Competitive Factors Affecting U.S. and Brazilian Agricultural Sales in Selected Third Country Markets AGENCY: United States... Committee in investigation No. 332-524, Brazil: Competitive Factors In Brazil Affecting U.S. and Brazilian...

  20. Traceable working standards with SI units of radiance for characterizing the measurement performance of investigational clinical NIRF imaging devices

    NASA Astrophysics Data System (ADS)

    Zhu, Banghe; Rasmussen, John C.; Litorja, Maritoni; Sevick-Muraca, Eva M.

    2017-03-01

    All medical devices for Food and Drug market approval require specifications of performance based upon International System of Units (SI) or units derived from SI for reasons of traceability. Recently, near-infrared fluorescence (NIRF) imaging devices of a variety of designs have emerged on the market and in investigational clinical studies. Yet the design of devices used in the clinical studies vary widely, suggesting variable device performance. Device performance depends upon optimal excitation of NIRF imaging agents, rejection of backscattered excitation and ambient light, and selective collection of fluorescence emanating from the fluorophore. There remains no traceable working standards with SI units of radiance to enable prediction that a given molecular imaging agent can be detected in humans by a given NIRF imaging device. Furthermore, as technologies evolve and as NIRF imaging device components change, there remains no standardized means to track device improvements over time and establish clinical performance without involving clinical trials, often costly. In this study, we deployed a methodology to calibrate luminescent radiance of a stable, solid phantom in SI units of mW/cm2/sr for characterizing the measurement performance of ICCD and IsCMOS camera based NIRF imaging devices, such as signal-to-noise ratio (SNR) and contrast. The methodology allowed determination of superior SNR of the ICCD over the IsCMOS system; comparable contrast of ICCD and IsCMOS depending upon binning strategies.