Formation and retention of methane in coal

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hucka, V.J.; Bodily, D.M.; Huang, H.

1992-05-15

The formation and retention of methane in coalbeds was studied for ten Utah coal samples, one Colorado coal sample and eight coal samples from the Argonne Premium Coal Sample Bank.Methane gas content of the Utah and Colorado coals varied from zero to 9 cm{sup 3}/g. The Utah coals were all high volatile bituminous coals. The Colorado coal was a gassy medium volatile bituminous coal. The Argonne coals cover a range or rank from lignite to low volatile bituminous coal and were used to determine the effect of rank in laboratory studies. The methane content of six selected Utah coal seamsmore » and the Colorado coal seam was measured in situ using a special sample collection device and a bubble desorbometer. Coal samples were collected at each measurement site for laboratory analysis. The cleat and joint system was evaluated for the coal and surrounding rocks and geological conditions were noted. Permeability measurements were performed on selected samples and all samples were analyzed for proximate and ultimate analysis, petrographic analysis, {sup 13}C NMR dipolar-dephasing spectroscopy, and density analysis. The observed methane adsorption behavior was correlated with the chemical structure and physical properties of the coals.« less

Formation and retention of methane in coal. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hucka, V.J.; Bodily, D.M.; Huang, H.

1992-05-15

The formation and retention of methane in coalbeds was studied for ten Utah coal samples, one Colorado coal sample and eight coal samples from the Argonne Premium Coal Sample Bank.Methane gas content of the Utah and Colorado coals varied from zero to 9 cm{sup 3}/g. The Utah coals were all high volatile bituminous coals. The Colorado coal was a gassy medium volatile bituminous coal. The Argonne coals cover a range or rank from lignite to low volatile bituminous coal and were used to determine the effect of rank in laboratory studies. The methane content of six selected Utah coal seamsmore » and the Colorado coal seam was measured in situ using a special sample collection device and a bubble desorbometer. Coal samples were collected at each measurement site for laboratory analysis. The cleat and joint system was evaluated for the coal and surrounding rocks and geological conditions were noted. Permeability measurements were performed on selected samples and all samples were analyzed for proximate and ultimate analysis, petrographic analysis, {sup 13}C NMR dipolar-dephasing spectroscopy, and density analysis. The observed methane adsorption behavior was correlated with the chemical structure and physical properties of the coals.« less

30 CFR 75.325 - Air quantity.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Air quantity. 75.325 Section 75.325 Mineral... SAFETY STANDARDS-UNDERGROUND COAL MINES Ventilation § 75.325 Air quantity. (a)(1) In bituminous and lignite mines the quantity of air shall be at least 3,000 cubic feet per minute reaching each working face...

30 CFR 75.325 - Air quantity.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Air quantity. 75.325 Section 75.325 Mineral... SAFETY STANDARDS-UNDERGROUND COAL MINES Ventilation § 75.325 Air quantity. (a)(1) In bituminous and lignite mines the quantity of air shall be at least 3,000 cubic feet per minute reaching each working face...

30 CFR 75.325 - Air quantity.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Air quantity. 75.325 Section 75.325 Mineral... SAFETY STANDARDS-UNDERGROUND COAL MINES Ventilation § 75.325 Air quantity. (a)(1) In bituminous and lignite mines the quantity of air shall be at least 3,000 cubic feet per minute reaching each working face...

30 CFR 75.325 - Air quantity.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Air quantity. 75.325 Section 75.325 Mineral... SAFETY STANDARDS-UNDERGROUND COAL MINES Ventilation § 75.325 Air quantity. (a)(1) In bituminous and lignite mines the quantity of air shall be at least 3,000 cubic feet per minute reaching each working face...

30 CFR 75.325 - Air quantity.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Air quantity. 75.325 Section 75.325 Mineral... SAFETY STANDARDS-UNDERGROUND COAL MINES Ventilation § 75.325 Air quantity. (a)(1) In bituminous and lignite mines the quantity of air shall be at least 3,000 cubic feet per minute reaching each working face...

Development of clean coal and clean soil technologies using advanced agglomeration technologies

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ignasiak, B.; Pawlak, W.; Szymocha, K.

1990-04-01

The specific objectives of the bituminous coal program were to explore and evaluate the application of advanced agglomeration technology for: (1)desulphurization of bituminous coals to sulphur content acceptable within the current EPA SO{sub 2} emission guidelines; (2) deashing of bituminous coals to ash content of less than 10 percent; and (3)increasing the calorific value of bituminous coals to above 13,000 Btu/lb. (VC)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sari, A.; Geze, Y.

The studied area is a lake basin located in Bolu basin in Turkey. In the basin, from Upper Cretaceous to Upper Miocene 3,000-m thickness sediments were deposited. Upper Miocene Himmetoglu formation consisted of sandstone, claystone, and marl. To the middle level of the formation are located coal, bituminous limestone, and bituminous shales. In the basin, there are two coal beds whose thicknesses range from 1 to 13 m. The coals are easily breakable and black in color. In the coal beds exists some bituminous limestone and bituminous shales, and their thicknesses are between 5 and 45 cm. The amount ofmore » organic matter of the bituminous rocks from the Upper Miocene Himmetoglu formation are between 6.83 and 56.34 wt%, and the amount of organic matter of the bituminous limestone from the formation are between 13.58 and 57.16 wt%. These values indicate that these rocks have very good source potential. According to hydrogen index (HI), S2/S3, HI-T{sub max}, and HI-OI (oxygen index) parameters, kerogen types of the bituminous rocks and coals belonging to Upper Miocene Himmetoglu formation are Type I, Type II, and Type III. In accordance with HI, S2/S3, HI-T{sub max}, and HI-OI parameters, the bituminous rocks and coals from the Upper Miocene Himmetoglu formation are mostly immature.« less

Review of a bituminous concrete statistical specification : final report.

DOT National Transportation Integrated Search

1971-01-01

The statistically oriented specification for bituminous concrete production reviewed in this report was used as a basis for acceptance of more than one million tons of bituminous concrete in 1970. Data obtained from this system were analyzed for grad...

Effect of baghouse fines on compaction of bituminous concrete.

DOT National Transportation Integrated Search

1981-01-01

Four bituminous mixes were tested in the laboratory to determine the effect of variations in the concentration of baghouse fines on the density and tenderness of bituminous mixes. On the basis of results indicating that the gradation of baghouse fine...

Influence of association of "EVA-NBR" on indirect tensile strength of modified bituminous concrete

NASA Astrophysics Data System (ADS)

Chinoun, M.; Soudani, K.; Haddadi, S.

2016-04-01

The aim of this work is to contribute to the improvement of the mechanical properties of bituminous concrete by modification of bituminous concrete. In this study, we present the results of the indirect tensile strength "ITS" of modified bituminous concrete by the combination of two modifiers, one is a plastomer EVA (Ethylene Vinyl Acetate) and the other is a industrial waste from the shoe soles grinding NBR (Nitrile Butadiene Rubber) as crumb rubber. To modify the bitumen a wet process was used. The results show that the modification of bitumen by EVA-NBR combination increases their resistance to the indirect traction "ITS" compared to the bituminous concrete control. The mixture of 5% [50% EVA+ 50% NBR] is given the best result among the other associations.

Effect of Cement on Properties of Over-Burnt Brick Bituminous Concrete Mixes

NASA Astrophysics Data System (ADS)

Sarkar, Dipankar; Pal, Manish

2016-06-01

The present investigation is carried out to propose the use of cement coated over burnt brick aggregate in the preparation of bituminous concrete mix. The effect of cement on various mechanical properties such as Marshall stability, flow, Marshall quotient (stability to flow ratio), indirect tensile strength, stripping, rutting and fatigue life of bituminous concrete overlay has been evaluated. In this study, different cement percentages such as 2, 3, 4 and 5 % by weight of aggregate have been mixed with Over Burnt Brick Aggregate (OBBA). The laboratory results indicate that bituminous concrete prepared by 4 % cement coated OBBA gives the highest Marshall stability. The bituminous concrete mix with 4 % cement shows considerable improvement in various mechanical properties of the mix compared to the plain OBBA concrete mix.

Investigation on Using SBS and Active Carbon Filler to Reduce the VOC Emission from Bituminous Materials.

PubMed

Cui, Peiqiang; Wu, Shaopeng; Li, Fuzhou; Xiao, Yue; Zhang, Honghua

2014-08-26

Bituminous materials are playing a vital role in pavement design and the roofing industry because of outstanding properties. Unfortunately, bituminous materials will release volatile organic compounds (VOC), making them non-environmentally friendly. Therefore, technologies that can be used to decrease the VOC emission are urgently required. In this research, the VOC emission and material behaviors were analyzed and compared to investigate the possibility of adding styrene butadiene styrene (SBS) and active carbon filler into bituminous materials to develop environmentally-friendly materials. Thermal gravimetric analysis-mass spectrometry (TG-MS) and ultraviolet-visible spectroscopy testing (UV-Vis) were employed to characterize the VOC emission process. Temperature sweep testing and frequency sweep testing were conducted to evaluate the rheological properties of bituminous materials. Research results indicated that the combined introduction of 4 wt% styrene butadiene styrene (SBS) and 4 wt% active carbon filler cannot only significantly lower the VOC emission speed and amount, but also improve the deformation resistance behavior at a higher temperature. SBS and active carbon filler can be used to reduce the VOC emission form bituminous materials.

Investigation on Using SBS and Active Carbon Filler to Reduce the VOC Emission from Bituminous Materials

PubMed Central

Cui, Peiqiang; Wu, Shaopeng; Li, Fuzhou; Xiao, Yue; Zhang, Honghua

2014-01-01

Bituminous materials are playing a vital role in pavement design and the roofing industry because of outstanding properties. Unfortunately, bituminous materials will release volatile organic compounds (VOC), making them non-environmentally friendly. Therefore, technologies that can be used to decrease the VOC emission are urgently required. In this research, the VOC emission and material behaviors were analyzed and compared to investigate the possibility of adding styrene butadiene styrene (SBS) and active carbon filler into bituminous materials to develop environmentally-friendly materials. Thermal gravimetric analysis-mass spectrometry (TG-MS) and ultraviolet-visible spectroscopy testing (UV-Vis) were employed to characterize the VOC emission process. Temperature sweep testing and frequency sweep testing were conducted to evaluate the rheological properties of bituminous materials. Research results indicated that the combined introduction of 4 wt% styrene butadiene styrene (SBS) and 4 wt% active carbon filler cannot only significantly lower the VOC emission speed and amount, but also improve the deformation resistance behavior at a higher temperature. SBS and active carbon filler can be used to reduce the VOC emission form bituminous materials. PMID:28788181

Sequential solvent extraction for the modes of occurrence of selenium in coals of different ranks from the Huaibei Coalfield, China

USGS Publications Warehouse

Zhang, Y.; Liu, Gaisheng; Chou, C.-L.; Wang, L.; Kang, Y.

2007-01-01

Forms of selenium in bituminous coal, anthracite, and cokeite (natural coke) from Huaibei Coalfield, Anhui, China, have been determined by sequential solvent extraction. The selenium content in bulk samples is 4.0, 2.4, and 2.0 ??g/g in bituminous coal, anthracite, and cokeite, respectively. The six forms of selenium determined by six-step solvent extraction are water-leachable, ion-exchangeable, organic matter-associated, carbonate-associated, silicate-associated, and sulfide-associated. The predominant forms of selenium in bituminous coal are organic matter-associated (39.0%), sulfide-associated (21.1%), and silicate bound (31.8%); these three forms account for 92% of the total. The organic matter bound-selenium decrease dramatically from bituminous coal (39.0%) to anthracite (11.6%) and to cokeite (0%), indicating that organic matter bound selenium is converted to other forms during metamorphism of the coal, most likely sulfide-form. The sulfide-associated form increased remarkably from bituminous coal (21.1%) to anthracite (50.4%) and cokeite (54.5%), indicating the formation of selenium sulfide, possibly in pyrite during the transformation of bituminous coal to anthracite and cokeite. The silicate-associated selenium in bituminous coal (31.8%) is much higher than that in anthracite (16.4%) and cokeite (15.8%), indicating that silicate-associated selenium is partly converted to sulfide during metamorphism. ?? 2007 Zhang et al; licensee BioMed Central Ltd.

Promising Technologies of Mining and Processing of Solid Minerals

NASA Astrophysics Data System (ADS)

Shabaev, Sergey; Ivanov, Seregey; Vakhianov, Evgeniy

2017-11-01

The continuing growth in mineral extraction entails an increase in industrial waste, which in turn has a negative impact on the environment. Rubber-tired vehicles, in which the tires wear colossally, is mainly used as a transport for loading, unloading, transportation and other types of work in the extraction of solid minerals. The used tires are not disposed in any way, but are stored in special areas where harmful toxic substances are emitted under the influence of ultraviolet rays. Therefore, a decision was made to find a method for utilization and rational use of industrial waste in the road construction sector. The operating temperature of composite rubber-bituminous binders based on rubber crumb from the used automobile tires is estimated in this paper, which is necessary for assigning technological parameters of production and laying of asphalt-concrete mixtures produced on their basis. It is established that composite rubber-bituminous binders based on rubber chips from the used automobile tires, produced according to the two-stage technology, have the same viscosity as the original petroleum bitumen, at a temperature increased by 20°C.

Losses due to weather phenomena in the bituminous concrete construction industry in Wisconsin

NASA Technical Reports Server (NTRS)

Kuhn, H. A. J.

1973-01-01

The losses (costs) due to weather phenomena as they affect the bituminous concrete industry in Wisconsin were studied. The bituminous concrete industry's response to precipitation, in the form of rain, is identified through the use of a model, albeit crude, which identifies a typical industry decision-response mechanism. Using this mechanism, historical weather data and 1969 construction activity, dollar losses resulting from rain occurrences were developed.

Leaching characteristics of arsenic and selenium from coal fly ash: role of calcium

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tian Wang; Jianmin Wang; Yulin Tang

2009-05-15

Understanding the leaching behavior of arsenic (As) and selenium (Se) in coal fly ash is important in evaluating the potential environmental impact of coal fly ash. Batch experiments were employed to systematically investigate the leaching behavior of As and Se in two major types of coal fly ashes, bituminous coal ash and sub-bituminous coal ash, and to determine the underlying processes that control As and Se leaching. The effects of pH, solid/liquid (S/L) ratio, calcium addition, and leaching time on the release of As and Se were studied. Overall, bituminous coal ash leached significantly more As and Se than sub-bituminousmore » coal ash, and Se was more readily leachable, in both absolute concentration and relative fraction, than As for both types of fly ashes. Adsorption/desorption played a major role on As and Se leaching from bituminous coal ashes. However, calcium precipitation played the most important role in reducing As and Se leaching from sub-bituminous coal ashes in the entire experimental pH range. The leaching of As and Se from bituminous coal ashes generally increased with increases in the S/L ratio and leaching time. However, for sub-bituminous coal ashes, the leaching of As was not detected under most experimental conditions, while the leaching of Se increased with increases in the S/L ratio and leaching time. As{sup V} and Se{sup IV} were found to be the major species in all ash leachates in this study. 46 refs., 7 figs., 1 tab.« less

Applicability of the mixture of bituminous coal and anthracite to conventional pulverized coal firing boiler

DOE Office of Scientific and Technical Information (OSTI.GOV)

Takano, Shin-Ichi; Kiga, Takashi; Miyamae, Shigehiro

1994-12-31

In some future, it is expected for Japanese power stations to be hard to get a high-grade coal like a bituminous coal. We conducted therefore pilot scale tests of pulverized blends of bituminous coal and anthracite using a 1.2MWt tunnel furnace in order to evaluate the applicability of the blends of bituminous coal and anthracite to conventional pulverized coal firing boilers. One kind of bituminous coal and two kinds of anthracite, one was of low ash content and another was of high ash content, were prepared for the test. Previously to pilot scale tests, coal properties and ash properties ofmore » the blends of bituminous coal and anthracite were analyzed to estimate the characteristics of combustion, ash deposition, and so on. In the test, we investigated the combustion efficiency, NOx emission, characteristics of ignition stability and grindability changing the blend rate of anthracite. Results of our study indicated that the critical restrictions on the blending rate of anthracite were unburnt carbon in fly ash and NOx emission as for coals tested. The acceptable limitation on blending rate of anthracite was 10 and 20%, respectively for two kinds of conventional pulverized coal fired boiler. Concerning to the grindability, it became worse with increasing the blending rate of anthracite from grindability test using a roller mill, while it became better estimating from HGI.« less

Design and verification of bituminous mixtures with the increased content of reclaimed asphalt pavement

NASA Astrophysics Data System (ADS)

Bańkowski, Wojciech; Król, Jan; Gałązka, Karol; Liphardt, Adam; Horodecka, Renata

2018-05-01

Recycling of bituminous pavements is an issue increasingly being discussed in Poland. The analysis of domestic and foreign experience indicates a need to develop this technology in our country, in particular the hot feeding and production technologies. Various steps are being taken in this direction, including research projects. One of them is the InnGA project entitled: “Reclaimed asphalt pavement: Innovative technology of bituminous mixtures using material from reclaimed asphalt pavement”. The paper presents the results of research involving the design of bituminous mixtures in accordance with the required properties and in excess of the content of reclaimed asphalt permitted by the technical guidelines. It presents selected bituminous mixtures with the content of RAP of up to 50% and the results of tests from verification of industrial production of those mixtures. The article discusses the details of the design process of mixtures with a high content of reclaimed asphalt, the carried out production tests and discusses the results of tests under the verification of industrial production. Testing included basic tests according to the Polish technical requirements of WT- 2 and the extended functional testing. The conducted tests and analyses helped to determine the usefulness of the developed bituminous mixtures for use in experimental sections and confirmed the possibility of using an increased amount of reclaimed asphalt up to 50% in mixtures intended for construction of national roads.

Provincial variation of carbon emissions from bituminous coal: Influence of inertinite and other factors

USGS Publications Warehouse

Quick, J.C.; Brill, T.

2002-01-01

We observe a 1.3 kg C/net GJ variation of carbon emissions due to inertinite abundance in some commercially available bituminous coal. An additional 0.9 kg C/net GJ variation of carbon emissions is expected due to the extent of coalification through the bituminous rank stages. Each percentage of sulfur in bituminous coal reduces carbon emissions by about 0.08 kg C/net GJ. Other factors, such as mineral content, liptinite abundance and individual macerals, also influence carbon emissions, but their quantitative effect is less certain. The large range of carbon emissions within the bituminous rank class suggests that rank- specific carbon emission factors are provincial rather than global. Although carbon emission factors that better account for this provincial variation might be calculated, we show that the data used for this calculation may vary according to the methods used to sample and analyze coal. Provincial variation of carbon emissions and the use of different coal sampling and analytical methods complicate the verification of national greenhouse gas inventories. Published by Elsevier Science B.V.

Coal desulfurization by low temperature chlorinolysis, phase 1

NASA Technical Reports Server (NTRS)

Kalvinskas, J. J.; Hsu, G. C.; Ernest, J. B.; Andress, D. F.; Feller, D. R.

1977-01-01

The reported activity covers laboratory scale experiments on twelve bituminous, sub-bituminous and lignite coals, and preliminary design and specifications for bench-scale and mini-pilot plant equipment.

Design of bituminous mixes with high skid resistance.

DOT National Transportation Integrated Search

1979-01-01

Certain highway locations need exceptionally high skid resistance because of the alignment, geometry, and drainage of the roadway and the complex turning maneuvers required. Several beam specimens made of bituminous mixes incorporating unconventional...

Blended aggregate bituminous mixes.

DOT National Transportation Integrated Search

1975-01-01

Virginia has provided skid resistant pavements in the limestone area of the state by placing thin overlays of sand mixes incorporating local materials, by sprinkling highly skid resistant aggregates on limestone bituminous mixes prior to rolling, and...

Viscoelastic behaviour of cold recycled asphalt mixes

NASA Astrophysics Data System (ADS)

Cizkova, Zuzana; Suda, Jan

2017-09-01

Behaviour of cold recycled mixes depends strongly on both the bituminous binder content (bituminous emulsion or foamed bitumen) and the hydraulic binder content (usually cement). In the case of cold recycled mixes rich in bitumen and with low hydraulic binder content, behaviour is close to the viscoelastic behaviour of traditional hot mix asphalt. With decreasing bituminous binder content together with increasing hydraulic binder content, mixes are characteristic with brittle behaviour, typical for concrete pavements or hydraulically bound layers. The behaviour of cold recycled mixes with low content of both types of binders is similar to behaviour of unbound materials. This paper is dedicated to analysing of the viscoelastic behaviour of the cold recycled mixes. Therefore, the tested mixes contained higher amount of the bituminous binder (both foamed bitumen and bituminous emulsion). The best way to characterize any viscoelastic material in a wide range of temperatures and frequencies is through the master curves. This paper includes interesting findings concerning the dependency of both parts of the complex modulus (elastic and viscous) on the testing frequency (which simulates the speed of heavy traffic passing) and on the testing temperature (which simulates the changing climate conditions a real pavement is subjected to).

Reuse of steel slag in bituminous paving mixtures.

PubMed

Sorlini, Sabrina; Sanzeni, Alex; Rondi, Luca

2012-03-30

This paper presents a comprehensive study to evaluate the mechanical properties and environmental suitability of electric arc furnace (EAF) steel slag in bituminous paving mixtures. A variety of tests were executed on samples of EAF slag to characterize the physical, geometrical, mechanical and chemical properties as required by UNI EN specifications, focusing additionally on the volumetric expansion associated with hydration of free CaO and MgO. Five bituminous mixtures of aggregates for flexible road pavement were designed containing up to 40% of EAF slag and were tested to determine Marshall stability and indirect tensile strength. The leaching behaviour of slag samples and bituminous mixtures was evaluated according to the UNI EN leaching test. The tested slag showed satisfactory physical and mechanical properties and a release of pollutants generally below the limits set by the Italian code. Tests on volume stability of fresh materials confirmed that a period of 2-3 months is necessary to reduce effects of oxides hydration. The results of tests performed on bituminous mixtures with EAF slag were comparable with the performance of mixtures containing natural aggregates and the leaching tests provided satisfactory results. Copyright © 2012 Elsevier B.V. All rights reserved.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sutcu, H.; Toroglu, I.; Piskin, S.

Turkey, especially Zonguldak on the West Coast of Black Sea region, has large reserves of bituminous coal that can be used either directly or in blends with other coals for metallurgical coke production. It is possible to predict the coking properties of these coals by petrographic analysis. In this study, semi- and non-coking coals were blended with coking bituminous coals in varying proportions and an estimation was made as to their stability factors through petrographic techniques. It was established that semi- and non-coking bituminous coals could be used in the production of metallurgical coke.

Product evaluation : bituminous pavement rejuvenator

DOT National Transportation Integrated Search

1986-07-03

This report contains a product evaluation of K.A.E. Paving Consultant's Bituminous Pavement Rejuvenator (BPR). BPR is a coal tar product consisting of a low viscosity blend of aromatic oils designed to penetrate the asphalt, and rejuvenate and plasti...

Design of bituminous surface mixes with high skid resistance.

DOT National Transportation Integrated Search

1974-01-01

The Virginia Highway Research Council has proposed a study of the skid resistance of bituminous surfaces incorporating relatively hard and expensive aggregates. The hardness of the aggregates to be used aluminum oxide (Exolon) and calcined kaolin -- ...

Reexamination of cold weather paving specifications for bituminous concrete.

DOT National Transportation Integrated Search

1978-01-01

The cold weather paving specification for bituminous concrete adopted in 1970 was reexamined to determine its effectiveness and any need for revisions. Density and temperature measurements were obtained on five field projects and observations were ma...

Aerobic Biofilms Grown from Athabasca Watershed Sediments Are Inhibited by Increasing Concentrations of Bituminous Compounds

PubMed Central

Lawrence, John R.; Sanschagrin, Sylvie; Roy, Julie L.; Swerhone, George D. W.; Korber, Darren R.; Greer, Charles W.

2013-01-01

Sediments from the Athabasca River and its tributaries naturally contain bitumen at various concentrations, but the impacts of this variation on the ecology of the river are unknown. Here, we used controlled rotating biofilm reactors in which we recirculated diluted sediments containing various concentrations of bituminous compounds taken from the Athabasca River and three tributaries. Biofilms exposed to sediments having low and high concentrations of bituminous compounds were compared. The latter were 29% thinner, had a different extracellular polysaccharide composition, 67% less bacterial biomass per μm2, 68% less cyanobacterial biomass per μm2, 64% less algal biomass per μm2, 13% fewer protozoa per cm2, were 21% less productive, and had a 33% reduced content in chlorophyll a per mm2 and a 20% reduction in the expression of photosynthetic genes, but they had a 23% increase in the expression of aromatic hydrocarbon degradation genes. Within the Bacteria, differences in community composition were also observed, with relatively more Alphaproteobacteria and Betaproteobacteria and less Cyanobacteria, Bacteroidetes, and Firmicutes in biofilms exposed to high concentrations of bituminous compounds. Altogether, our results suggest that biofilms that develop in the presence of higher concentrations of bituminous compounds are less productive and have lower biomass, linked to a decrease in the activities and abundance of photosynthetic organisms likely due to inhibitory effects. However, within this general inhibition, some specific microbial taxa and functional genes are stimulated because they are less sensitive to the inhibitory effects of bituminous compounds or can degrade and utilize some bitumen-associated compounds. PMID:24056457

Trees for strip-mined lands

Treesearch

George Hart; William R. Byrnes

1960-01-01

Open-pit or strip mining has become an important method of mining bituminous coal in Pennsylvania. In 1958 some 19.5 million tons of soft coal - 29 percent of the total bituminous production in the State - were produced by this method.

Cold weather paving requirements for bituminous concrete.

DOT National Transportation Integrated Search

1973-01-01

Cold weather paving specifications were developed from work by Corlew and Dickson, who used a computer solution to predict the cooling rate of bituminous concrete. Virginia had used a minimum atmospheric temperature as a criterion; however, it was ev...

An evaluation of bituminized fiber pipe culverts.

DOT National Transportation Integrated Search

1970-01-01

This report describes the results to date in a limited study, including laboratory tests and field evaluations, of the suitability of bituminized fiber pipe for use as highway culverts. Crushing strength data obtained from three-edge bearing tests in...

Investigation of asphalt content design for open-graded bituminous mixes.

DOT National Transportation Integrated Search

1974-01-01

Several design procedures associated with determining the proper asphalt content for open-graded bituminous mixes were investigated. Also considered was the proper amount of tack coat that should be placed on the old surface prior to paving operation...

Effect of antistripping additives on the compaction of bituminous concrete.

DOT National Transportation Integrated Search

1981-01-01

The objective of this investigation was to determine the effect of antistripping additives on the compaction of bituminous concrete. To do this, the densities obtained on test sections with and without additive were compared. Comparisons of nuclear d...

Polygenic formation model of the planet's bituminous belts

NASA Astrophysics Data System (ADS)

Dmitrievsky, A. N.; Balanyuk, I. E.

2011-05-01

In recent years, much attention has been paid to nontraditional hydrocarbon sources. Today the portion of nontraditional gas in the world extraction is 15% or 450 billion cubic meters, which hat makes up the volume of total gas exports from Russia. As is known, the easy-prospecting oil has been already found. The innovative technologies in geophysics, drilling, and excavation and the increased extraction coefficient expect further development and industrial compliance with these requirements. Based on calculations, the world oil reserves are now one trillion of stock tank barrels and one trillion barrels have been already extracted. The evergrowing demand for energy gives rise to the necessity of searching for and extracting more oil resources, and both these aspects are unique problems. The search for profitable petroleum deposits has become more and more difficult even in the leading companies. The increment of the world resources is a key vital question; therefore, the elaboration of criteria for the discovery of nontraditional deposits take on special significance in the economic respect. The authors are working out a conception that will be a guideline for future finding of the richest oil deposits in active geodynamic zones. For the first time, we suggest the polygenic formation model of the planet's bituminous belts.

Vibratory compaction of bituminous concrete -- where does it stand?.

DOT National Transportation Integrated Search

1974-01-01

A questionnaire concerning the specifications on the use of vibratory rollers on bituminous concrete was sent to the 50 state highway agencies. All 50 agencies replied, and many indicated that their specs were in a state of change. The report present...

Installation report : thick lift bituminous base : construction and materials phase.

DOT National Transportation Integrated Search

1972-01-01

During the 1970 construction season, the Basic Construction Company of Newport News, laid a 9-inch bituminous concrete base course in a single lift directly on an unimproved subgrade on a section of Route 31 just southwest of Williamsburg, as specifi...

Sawing and sealing joints in bituminous pavements to control cracking

DOT National Transportation Integrated Search

1996-03-01

The practice of sawing and sealing joints in pavements is not a new one. In fact, it is common practice in the construction of jointed Portland Cement Concrete (PCC) pavements. The idea of sawing and sealing joints in bituminous pavements is much les...

Use of carbon black in bituminous concrete in Virginia.

DOT National Transportation Integrated Search

1981-01-01

In an attempt to verify the claim that the addition of carbon black to bituminous concrete increases its stability and performance, a test section placed on a deformed bridge deck surface near Altavista and one on Route 360 near Richmond are being ev...

Synergistic effect on thermal behavior during co-pyrolysis of lignocellulosic biomass model components blend with bituminous coal.

PubMed

Wu, Zhiqiang; Wang, Shuzhong; Zhao, Jun; Chen, Lin; Meng, Haiyu

2014-10-01

Co-thermochemical conversion of lignocellulosic biomass and coal has been investigated as an effective way to reduce the carbon footprint. Successful evaluating on thermal behavior of the co-pyrolysis is prerequisite for predicting performance and optimizing efficiency of this process. In this paper, pyrolysis and kinetics characteristics of three kinds of lignocellulosic biomass model components (cellulose, hemicellulose, and lignin) blended with a kind of Chinese bituminous coal were explored by thermogravimetric analyzer and Kissinger-Akahira-Sunose method. The results indicated that the addition of model compounds had different synergistic effects on thermal behavior of the bituminous coal. The cellulose showed positive synergistic effects on the thermal decomposition of the coal bituminous coal with lower char yield than calculated value. For hemicellulose and lignin, whether positive or negative synergistic was related to the mixed ratio and temperature range. The distribution of the average activation energy values for the mixtures showed nonadditivity performance. Copyright © 2014 Elsevier Ltd. All rights reserved.

Twenty-Second Annual Report of the Director of the United States Geological Survey, 1900-1901: Part I - Director's report and a paper on asphalt and bituminous rock deposits

USGS Publications Warehouse

Walcott, Charles D.

1902-01-01

The work of the Geological Survey during the fiscal year 1900-01 was mainly a continuation of that of previous years, described in former reports. The organization was changed somewhat (see p. 48), but in a general way similar results were reached, which added materially to the sum of geologic and geographic knowledge. The detailed record of accomplishment, both in field and in office, will be found on later pages, under the heading " Work of the year" (p. 53). In this introduction some subjects of special interest will receive consideration.

Development of performance-based guidelines for selection of bituminous-based hot-poured pavement crack sealant : an executive summary report.

DOT National Transportation Integrated Search

2009-01-01

This report summarizes research presented in separate technical reports, papers, and journal articles that collectively document the development of a systematic process to aid in the selection of appropriate bituminous hot-poured sealants for pavemen...

Liquefaction of sub-bituminous coal

DOEpatents

Schindler, Harvey D.; Chen, James M.

1986-01-01

Sub-bituminous coal is directly liquefied in two stages by use of a liquefaction solvent containing insoluble material as well as 850.degree. F.+ material and 850.degree. F.- material derived from the second stage, and controlled temperature and conversion in the second stage. The process is in hydrogen balance.

Critical Elements in Fly Ash from the Combustion of Bituminous Coal in Major Polish Power Plants

NASA Astrophysics Data System (ADS)

Bielowicz, Barbara; Botor, Dariusz; Misiak, Jacek; Wagner, Marian

2018-03-01

The concentration of critical elements, including such REE as Fe, Co, W, Zn, Cr, Ni, V, Mn, Ti, Ag, Ga, Ta, Sr, Li, and Cu, in the so-called fly ash obtained from the 9 Polish power plants and 1 thermal power station has been determined. The obtained values, compared with the global average concentration in bituminous coal ash and sedimentary rocks (Clarke values), have shown that the enrichment of fly ash in the specified elements takes place in only a few bituminous coal processing sites in Poland. The enrichment factor (EF) is only slightly higher (the same order of magnitude) than the Clarke values. The enrichment factor in relation to the Clarke value in the Earth's crust reached values above 10 in all of the examined ashes for the following elements: Cr, Ni, V, W, and, in some ash samples, also Cu and Zn. The obtained values are low, only slightly higher than the global average concentrations in sedimentary rocks and bituminous coal ashes. The ferromagnetic grains (microspheres) found in bituminous coal fly ashes seem to be the most economically prospective in recovery of selected critical elements. The microanalysis has shown that iron cenospheres and plerospheres in fly ash contain, in addition to enamel and iron oxides (magnetite and hematite), iron spinels enriched in Co, Cr, Cu, Mn, Ni, W, and Zn.

The leaching characteristics of selenium from coal fly ashes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, T.; Wang, J.; Burken, J.G.

2007-11-15

The leaching characteristics of selenium from several bituminous and subbituminous coal fly ashes under different pH conditions were investigated using batch methods. Results indicated that pH had a significant effect on selenium leaching from bituminous coal ash. The minimum selenium leaching occurred in the pH range between 3 and 4, while the maximum selenium leaching occurred at pH 12. The release of selenium from subbituminous coal ashes was very low for the entire experimental pH range, possibly due to the high content of calcium which can form hydration or precipitation products as a sink for selenium. The adsorption results formore » different selenium species indicated that Se(VI) was hardly adsorbable on either bituminous coal ashes or subbitumminous coal ashes at any pH. However, Se(I) was highly adsorbed by bituminous coal ashes under acidic pH conditions and was mostly removed by subbitumminous coal ashes across the entire pH range. This result suggests that the majority of selenium released from the tested fly ashes was Se(IV). A speciation-based model was developed to simulate the adsorption of Se(IV) on bituminous coal fly ash, and the pH-independent adsorption constants of HSeO{sup 3-} and SeO{sub 3}{sup 2-} were determined. The modeling approach is useful for understanding and predicting the release process of selenium from fly ash.« less

Treatments for clays in aggregates used to produce cement concrete, bituminous materials, and chip seals : technical report.

DOT National Transportation Integrated Search

2013-07-01

The clay contamination of coarse and fine aggregates and its effects on pavement performance of portland cement concrete, bituminous mixes and chip seals is a major concern for Texas Department of Transportation. We proposed (i) to determine what typ...

Study of bituminous surface treatments in Virginia : Phase II, Summer, 1964 : Distribution characteristics of materials, effectiveness of one size aggregate, setting time.

DOT National Transportation Integrated Search

1970-01-01

Distribution Characteristics of Materials: Ten bituminous distributors and ten chip spreading operations were investigated the former by cotton pad, cup, and trough tests; the latter by measuring the distance covered by a truckload and by placing pan...

INVESTIGATION OF PRIMARY FINE PARTICULATE MATTER FROM COAL COMBUSTION BY COMPUTER-CONTROLLED SCANNING ELECTRON MICROSCOPY

EPA Science Inventory

The particle size distributions, morphologies, and chemical composition distributions of 14 coal fly ash (CFA) samples produced by the combustion of four western U.S. coals (two subbituminous, one lignite, and one bituminous) and three eastern U.S. coals (all bituminous) have bee...

Study of bituminous surface treatments in Virginia : analysis of factors that significantly influence the quality of bituminous surface treatments.

DOT National Transportation Integrated Search

1970-01-01

It is obvious that many variables may influence the quality of a surface treatment, but the relative importance of the many variables involved is a matter of conjecture. The purpose of this study was to define those variables which do significantly i...

Potential of water-washing of rape straw on thermal properties and interactions during co-combustion with bituminous coal.

PubMed

Ma, Qiulin; Han, Lujia; Huang, Guangqun

2017-06-01

The aim of this work was to study the thermal properties and interactions during co-combustion of rape straw (RS) before and after water-washing with bituminous coal. A series of experiments was conducted to investigate the properties and interactions during co-combustion of RS with bituminous coal (at 10, 20, 40 and 60% RS). The feasibility and potential of water-washing as an RS pre-treatment was also explored. Reactivity and the amount of heat released followed a quadratic trend, while changes to the degree of interactions between the fuels conformed to a cosine curve. Water-washing increased the ignition and burn-out temperatures and slightly decreased reactivity. Demineralization negatively affected the previously synergistic co-firing relationship, nevertheless, the amount of heat released increased by 10.28% and the average activation energy (146kJ/mol) was lower than that of the unwashed blend (186kJ/mol). Overall, water-washing of RS could prove a useful pre-treatment before co-combustion with bituminous coal. Copyright © 2017 Elsevier Ltd. All rights reserved.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Young, B.C.; Musich, M.A.

A fixed-bed reactor system with continuous Hg{sup 0} analysis capabilities was used to evaluate commercial carbon sorbents for the removal of elemental mercury from simulated flue gas. The objectives of the program were to compare the sorbent effectiveness under identical test conditions and to identify the effects of various flue gas components on elemental mercury sorption. Sorbents tested included steam-activated lignite, chemically activated hardwood, chemically activated bituminous coal, iodated steam-activated coconut shell, and sulfur-impregnated steam-activated bituminous coal. The iodated carbon was the most effective sorbent, showing over 99% mercury removal according to U.S. Environmental Protection Agency (EPA) Method 101A. Datamore » indicate that adding O{sub 2} at 4 vol% reduced the effectiveness of the steam-activated lignite, chemically activated hardwood, and sulfur- impregnated steam-activated bituminous coal. Adding SO{sub 2} at 500 ppm improved the mercury removal of the sulfur-impregnated carbon. Further, the presence of HCl gas (at 50 ppm) produced an order of magnitude increase in mercury removal with the chemically activated and sulfur-impregnated bituminous coal-based carbons.« less

Influence of selected test parameters on measured values during the MSCR test

NASA Astrophysics Data System (ADS)

Benešová, Lucie; Valentin, Jan

2017-09-01

One of today’s most commonly used test on a Dynamic Shear Rheometer (DSR) is the Multiple Stress Creep Recovery (MSCR) test. The test is described in the standard EN 16659, which is valid in the Czech Republic since October 2016. The principle of the test is based on repeated loading and recovering of a bitumen sample, according to which it is possible to determine the percentage of elastic recovery (R) and non-recoverable creep compliance (Jnr) of the bituminous binder. This method has been recently promoted as the most suitable test for assessing the resistance of bituminous binders to permanent deformation. The test is performed at higher temperatures and is particularly suitable for modified bituminous binders. The paper deals with the comparison of the different input parameters set on the DSR device - different levels of stress, temperature of test, the geometry of the measuring device and also a comparison of the results for a different number of loading cycles. The research study was focused mainly on modified bituminous binders, but to compare the MSCR test it is performed even with conventional paving grade binders.

Hydrocarbon source potential and maturation in eocene New Zealand vitrinite-rich coals: Insights from traditional coal analyses, and Rock-Eval and biomarker studies

USGS Publications Warehouse

Newman, J.; Price, L.C.; Johnston, J.H.

1997-01-01

The results of traditional methods of coal characterisation (proximate, specific energy, and ultimate analyses) for 28 Eocene coal samples from the West Coast of New Zealand correspond well with biomarker ratios and Rock-Eval analyses. Isorank variations in vitrinite fluorescence and reflectance recorded for these samples are closely related to their volatile-matter content, and therefore indicate that the original vitrinite chemistry is a key controlling factor. By contrast, the mineral-matter content and the proportion of coal macerals present appear to have had only a minor influence on the coal samples' properties. Our analyses indicate that a number of triterpane biomarker ratios show peak maturities by high volatile bituminous A rank; apparent maturities are then reversed and decline at the higher medium volatile bituminous rank. The Rock-Eval S1 +S2 yield also maximizes by high volatile bituminous A rank, and then declines; however, this decline is retarded in samples with the most hydrogen-rich (perhydrous) vitrinites. These Rock-Eval and biomarker trends, as well as trends in traditional coal analyses, are used to define the rank at which expulsion of gas and oil occurs from the majority of the coals. This expulsion commences at high volatile A bituminous rank, and persists up to the threshold of medium volatile bituminous rank (c. 1.1% Ro ran. or 1.2% Ro max in this sample set), where marked hydrocarbon expulsion from perhydrous vitrinites begins to take place.

Size-resolved Pb distribution in the Athabasca River shows snowmelt in the bituminous sands region an insignificant source of dissolved Pb

NASA Astrophysics Data System (ADS)

Javed, Muhammad Babar; Cuss, Chad W.; Grant-Weaver, Iain; Shotyk, William

2017-03-01

Lead (Pb) is a metal of special importance because of its long history of commercial and industrial use, global atmospheric contamination accelerated by the use of gasoline additives, and health effects, with children being especially vulnerable. Global atmospheric Pb pollution reached its zenith in the 1970’s, but subsequent impacts on freshwater aquatic systems are poorly understood. Employing metal-free sampling and handling protocols, we show that snowmelt from the Athabasca bituminous sands region is an insignificant source of dissolved Pb to the Athabasca River (AR). Total Pb in the AR is low, and almost entirely in particulate form. Lead in the suspended solids in the AR exactly follows thorium (Th), a conservative lithophile element, and a linear regression of Pb against Th (Pb = 1.6 × Th + 0.0 R2 = 0.99) yields a slope identical to the Pb/Th ratio in the Upper Continental Crust. In the “dissolved” fraction, the Pb/Th ratio is equivalent to that of deep, open ocean seawater; and dominated by colloidal forms. Taken together, these results show that the efforts of recent decades to reduce anthropogenic Pb to the environment have been successful: Pb loading to the river can now be explained predominantly by natural processes, namely erosion plus chemical weathering.

PILOT-SCALE STUDY OF THE EFFECT OF SELECTIVE CATALYTIC REDUCTION CATALYST ON MERCURY SPECIATION IN ILLINOIS AND POWDER RIVER BASIN COAL COMBUSTION FLUE GASES

EPA Science Inventory

A study was conducted to investigate the effect of selective catalytic reduction (SCR) catalyst on mercury (Hg) speciation in bituminous and subbituminous coal combustion flue gases. Three different Illinois Basin bituminous coals (from high to low sulfur and chlorine) and one Po...

Process for removing pyritic sulfur from bituminous coals

DOEpatents

Pawlak, Wanda; Janiak, Jerzy S.; Turak, Ali A.; Ignasiak, Boleslaw L.

1990-01-01

A process is provided for removing pyritic sulfur and lowering ash content of bituminous coals by grinding the feed coal, subjecting it to micro-agglomeration with a bridging liquid containing heavy oil, separating the microagglomerates and separating them to a water wash to remove suspended pyritic sulfur. In one embodiment the coal is subjected to a second micro-agglomeration step.

Sprouting of thinned hybrid poplars on bituminous strip-mine spoils in Pennsylvania

Treesearch

Walter H. Davidson; Grant Davis

1972-01-01

Various thinning techniques were applied to 5-year old hybrid poplar stands on bituminous strip-mine spoils. Basal and stump sprays of 2, 4, 5-T in diesel oil were effective for killing the trees. There was no evidence that chemical treatments affected adjacent trees. Where trees were cut and stumps were not chemically treated, all clones sprouted prolifically....

Estimation and modeling of coal pore accessibility using small angle neutron scattering

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, Rui; Liu, Shimin; Bahadur, Jitendra

Gas diffusion in coal is controlled by nano-structure of the pores. The interconnectivity of pores not only determines the dynamics of gas transport in the coal matrix but also influences the mechanical strength. In this study, small angle neutron scattering (SANS) was employed to quantify pore accessibility for two coal samples, one of sub-bituminous rank and the other of anthracite rank. Moreover, a theoretical pore accessibility model was proposed based on scattering intensities under both vacuum and zero average contrast (ZAC) conditions. Our results show that scattering intensity decreases with increasing gas pressure using deuterated methane (CD 4) at lowmore » Q values for both coals. Pores smaller than 40 nm in radius are less accessible for anthracite than sub-bituminous coal. On the contrary, when the pore radius is larger than 40 nm, the pore accessibility of anthracite becomes larger than that of sub-bituminous coal. Only 20% of pores are accessible to CD 4 for anthracite and 37% for sub-bituminous coal, where the pore radius is 16 nm. For these two coals, pore accessibility and pore radius follows a power-law relationship.« less

Estimation and modeling of coal pore accessibility using small angle neutron scattering

DOE PAGES

Zhang, Rui; Liu, Shimin; Bahadur, Jitendra; ...

2015-09-04

Gas diffusion in coal is controlled by nano-structure of the pores. The interconnectivity of pores not only determines the dynamics of gas transport in the coal matrix but also influences the mechanical strength. In this study, small angle neutron scattering (SANS) was employed to quantify pore accessibility for two coal samples, one of sub-bituminous rank and the other of anthracite rank. Moreover, a theoretical pore accessibility model was proposed based on scattering intensities under both vacuum and zero average contrast (ZAC) conditions. Our results show that scattering intensity decreases with increasing gas pressure using deuterated methane (CD 4) at lowmore » Q values for both coals. Pores smaller than 40 nm in radius are less accessible for anthracite than sub-bituminous coal. On the contrary, when the pore radius is larger than 40 nm, the pore accessibility of anthracite becomes larger than that of sub-bituminous coal. Only 20% of pores are accessible to CD 4 for anthracite and 37% for sub-bituminous coal, where the pore radius is 16 nm. For these two coals, pore accessibility and pore radius follows a power-law relationship.« less

Microfluidic Synthesis of Ca-Alginate Microcapsules for Self-Healing of Bituminous Binder.

PubMed

Shu, Benan; Wu, Shaopeng; Dong, Lijie; Wang, Qing; Liu, Quantao

2018-04-19

This work aims to develop an original alginate micro-emulsion combining with droplets microfluidic method to produce multinuclear Ca-alginate microcapsules containing rejuvenator for the self-healing of bituminous binder. The sizes of the Ca-alginate microcapsules could be easily controlled by tuning flow rates of the continuous and dispersed phases. The addition of a surfactant Tween80 not only improved the stability of the emulsion, but it also effectively reduced the size of the microcapsules. Size predictive mathematical model of the microcapsules was proposed through the analysis of fluid force. Optical microscope and remote Fourier infrared test confirmed the multinuclear structure of Ca-alginate microcapsules. Thermogravimetric analysis showed that the microcapsules coated with nearly 40% rejuvenator and they remained intact during the preparation of bitumen specimen at 135 °C. Micro self-healing process of bituminous binder with multinuclear Ca-alginate microcapsules containing rejuvenator was monitored and showed enhanced self-healing performance. Tensile stress-recovery test revealed that the recovery rate increased by 32.08% (in the case of 5% microcapsules), which meant that the Ca-alginate microcapsules containing rejuvenator could effectively enhance the self-healing property of bituminous binder.

Continuous bench-scale slurry catalyst testing direct coal liquefaction rawhide sub-bituminous coal

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bauman, R.F.; Coless, L.A.; Davis, S.M.

In 1992, the Department of Energy (DOE) sponsored research to demonstrate a dispersed catalyst system using a combination of molybdenum and iron precursors for direct coal liquefaction. This dispersed catalyst system was successfully demonstrated using Black Thunder sub-bituminous coal at Wilsonville, Alabama by Southern Electric International, Inc. The DOE sponsored research continues at Exxon Research and Development Laboratories (ERDL). A six month continuous bench-scale program using ERDL`s Recycle Coal Liquefaction Unit (RCLU) is planned, three months in 1994 and three months in 1995. The initial conditions in RCLU reflect experience gained from the Wilsonville facility in their Test Run 263.more » Rawhide sub-bituminous coal which is similar to the Black Thunder coal tested at Wilsonville was used as the feed coal. A slate of five dispersed catalysts for direct coal liquefaction of Rawhide sub-bituminous coal has been tested. Throughout the experiments, the molybdenum addition rate was held constant at 100 wppm while the iron oxide addition rate was varied from 0.25 to 1.0 weight percent (dry coal basis). This report covers the 1994 operations and accomplishments.« less

Continuous bench-scale slurry catalyst testing direct coal liquefaction of rawhide sub-bituminous coal

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bauman, R.F.; Coless, L.A.; Davis, S.M.

In 1992, the Department of Energy (DOE) sponsored research to demonstrate a dispersed catalyst system using a combination of molybdenum and iron precursors for direct coal liquefaction. This dispersed catalyst system was successfully demonstrated using Black Thunder sub-bituminous coal at Wilsonville, Alabama by Southern Electric International, Inc. The DOE sponsored research continues at Exxon Research and Development Laboratories (ERDL). A six month continuous bench-scale program using ERDL`s Recycle Coal Liquefaction Unit (RCLU) is planned, three months in 1994 and three months in 1995. The initial conditions in RCLU reflect experience gained from the Wilsonville facility in their Test Run 263.more » Rawhide sub-bituminous coal which is similar to the Black Thunder coal tested at Wilsonville was used as the feed coal. A slate of five dispersed catalysts for direct coal liquefaction of Rawhide sub-bituminous coal has been tested. Throughout the experiments, the molybdenum addition rate was held constant at 100 wppm while the iron oxide addition rate was varied from 0.25 to 1.0 weight percent (dry coal basis). This report covers the 1994 operations and accomplishments.« less

A geochemical study of macerals from a Miocene lignite and an Eocene bituminous coal, Indonesia

USGS Publications Warehouse

Stankiewicz, B.A.; Kruge, M.A.; Mastalerz, Maria

1996-01-01

Optical and chemical studies of maceral concentrates from a Miocene lignite and an Eocene high-volatile bituminous C coal from southeastern Kalimantan, Indonesia were undertaken using pyro-Lysis, optical, electron microprobe and FTIR techniques Pyrolysis products of vitrinite from bituminous coal were dominated by straight-chain aliphatics and phenols. The huminite of the Miocene lignite produced mostly phenolic compounds upon pyrolysis. Differences in the pyrolysis products between the huminite and vitrinite samples reflect both maturation related and paleobotanical differences. An undefined aliphatic source and/or bacterial biomass were the likely contributors of n-alkyl moieties to the vitrinite. The resinite fraction in the lignite yielded dammar-derived pyrolysis products, as well as aliphatics and phenols as the products of admixed huminite and other liptinites. The optically defined resinite-rich fraction of the bituminous coal from Kalimantan produced abundant n-aliphatic moieties upon pyrolysis, but only two major resin markers (cadalene and 1,6-dimethylnaphthalene). This phenomenon is likely due to the fact that Eocene resins were not dammar-related. Data from the electron microprobe and Fourier transform infrared spectrometry strongly support the results obtained by Py GC MS and microscopy.

Process for preparing fine-grain metal carbide powder

DOEpatents

Kennedy, C.R.; Jeffers, F.P.

Fine-grain metal carbide powder suitable for use in the fabrication of heat resistant products is prepared by coating bituminous pitch on SiO/sub 2/ or Ta/sub 2/O/sub 5/ particles, heating the coated particles to convert the bituminous pitch to coke, and then heating the particles to a higher temperature to convert the particles to a carbide by reaction of said coke therewith.

Second-year results of hybrid poplar test plantings on bituminous strip-mine spoils in Pennsylvania

Treesearch

Grant Davis

1964-01-01

During the period 1946-49, The Pennsylvania State University established 22 experimental plantings of trees and shrubs on strip-mine spoil banks in the Bituminous Region of Pennsylvania to determine which species were best suited for revegetating such sites. When 10-year growth on the experimental plots was evaluated, a clone of hybrid poplar was found to have outgrown...

Performance of PAHs emission from bituminous coal combustion.

PubMed

Yan, Jian-Hua; You, Xiao-Fang; Li, Xiao-Dong; Ni, Ming-Jiang; Yin, Xue-Feng; Cen, Ke-Fa

2004-12-01

Carcinogenic and mutagenic polycyclic aromatic hydrocarbons (PAHs) generated in coal combustion have caused great environmental health concern. Seventeen PAHs (16 high priority PAHs recommended by USEPA plus Benzo[e]pyrene) present in five raw bituminous coals and released during bituminous coal combustion were studied. The effects of combustion temperature, gas atmosphere, and chlorine content of raw coal on PAHs formation were investigated. Two additives (copper and cupric oxide) were added when the coal was burned. The results indicated that significant quantities of PAHs were produced from incomplete combustion of coal pyrolysis products at high temperature, and that temperature is an important causative factor of PAHs formation. PAHs concentrations decrease with the increase of chlorine content in oxygen or in nitrogen atmosphere. Copper and cupric oxide additives can promote PAHs formation (especially the multi-ring PAHs) during coal combustion.

Comparison of coal reactivityduring conversion into different oxidizing medium

NASA Astrophysics Data System (ADS)

Korotkikh, A. G.; Slyusarskiy, K. V.; Larionov, K. B.; Osipov, V. I.

2016-10-01

Acoal conversion process of different coal samples into three different types of oxidizing medium (argon, air and steam) were studied by means of thermogravimetry. Two coal types with different metamorphism degree (lignite and bituminous coal) were used. The experimental procedure was carried out in non-isothermal conditions in temperature range from 373 K to 1273 K with 20 K/min heating rate. Purge gas consisted of argon and oxidizer with volumetric ratio 1:24 and had 250 ml/min flow rate.The ignition and burnout indexes were calculated to evaluate sample reactivity at different oxidizing mediums. The highest reactivity coefficient values in same atmosphere were obtained for lignite. It was caused by higher particle special surface area and volatile matter content.

Activities of the Institute of Chemical Processing of Coal at Zabrze

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dreszer, K.

1995-12-31

The Institute of Chemical Processing of Coal at Zabrze was established in 1955. The works on carbochemical technologies have been, therefore, carried out at the Institute for 40 years. The targets of the Institute`s activities are research, scientific and developing works regarding a sensible utilization of fuels via their processing into more refined forms, safe environment, highly efficient use of energy carriers and technological products of special quality. The Institute of Chemical Processing of Coal has been dealing with the following: optimized use of home hard coals; improvement of classic coal coking technologies, processing and utilization of volatile coking products;more » production technologies of low emission rate fuels for communal management; analyses of coal processing technologies; new technologies aimed at increasing the efficiency of coal utilization for energy-generating purposes, especially in industry and studies on the ecological aspects of these processes; production technologies of sorbents and carbon activating agents and technologies of the utilization; rationalization of water and wastes management in the metallurgical and chemical industries in connection with removal of pollution especially dangerous to the environment from wastes; utilization technologies of refined materials (electrode cokes, binders, impregnating agents) for making electrodes, refractories and new generation construction carbon materials; production technologies of high quality bituminous and bituminous and resin coating, anti-corrosive and insulation materials; environmentally friendly utilization technologies for power station, mine and other wastes, and dedusting processes in industrial gas streams.« less

The microstructure of petroleum vacuum residue films for bituminous concrete: a microscopy approach.

PubMed

Sourty, E D; Tamminga, A Y; Michels, M A J; Vellinga, W-P; Meijer, H E H

2011-02-01

Selected carbon-rich refinery residues ('binders') mixed with mineral particles can form composite materials ('bituminous concrete') with bulk mechanical properties comparable to those of cement concrete. The microstructural mechanism underlying the remarkable composite properties has been related to the appearance of a rigid percolating network consisting of asphaltenes and mineral particles [Wilbrink M. et al. (2005) Rigidity percolation in dispersions with a structured visco-elastic matrix. Phys. Rev. E71, 031402]. In this paper, we explore the microstructure of thin binder films of varying thickness with a number of microscopic characterization techniques, and attempt to relate the observed microstructure to the distinctive mechanical behaviour. Two binders, only one of which has been proven to be suitable for bituminous concrete were investigated, and their microstructure compared. Both binders show the formation of asphaltene aggregates. The binder suitable for bituminous concrete is distinguished by the fact that the asphaltenes show a stronger tendency towards such aggregation, due to a higher concentration and less stabilization in the maltene phase. They also show a clear affinity to other species (such as waxes) and may act as nucleation sites for crystals and aggregates of those species. © 2010 The Authors Journal compilation © 2010 The Royal Microscopical Society.

Transformism in Alberta: The Environmental Political Economy of the Bituminous Sands

NASA Astrophysics Data System (ADS)

Katz-Rosene, Ryan

This thesis attempts to help establish environmental political economy as a viable academic field while providing an example of work in the discipline. It offers an analysis of societal processes resulting in the co-optation and/or neutralization of critical environmentalist ideas. Using Alberta's bituminous sands as a case study, and a Gramsci-influenced eco-Marxist theory as a foundation, the thesis argues that the term 'environmental transformism' (inspired by the Gramscian term trasformismo) is helpful in describing and framing such processes. Accordingly, the ensuing chapters provide an analysis of why environmental transformism is happening in Alberta, and demonstrate how this mechanism works at protecting the status quo from threatening ideologies, thereby consolidating neoliberal capitalism. A concluding argument discusses the inherent dangers posed to society by the transformism of certain environmental subjectivities. The thesis begins by introducing the contentious social and environmental issues surrounding the development of the bituminous sands.

Simulation of one-dimensional heat transfer system based on the blended coal combustion

NASA Astrophysics Data System (ADS)

Jin, Y. G.; Li, W. B.; Cheng, Z. S.; Cheng, J. W.; liu, Y.

2017-12-01

In this paper, the supercritical boiler thermodynamic calculation model is studied. Three types of heat exchangers are proposed, namely furnace (total radiation type), semi-radiation and convection, and discussed. Two cases were simulated - mixing of two bituminous coals and mixing of a bituminous coal and lignite- order to analyze the performance on the flue gas side. The study shows that the influence of flue air leakage and gas distribution coefficient on the system.

Sorption of the monoterpenes α-pinene and limonene to carbonaceous geosorbents including biochar.

PubMed

Hale, Sarah E; Endo, Satoshi; Arp, Hans Peter H; Zimmerman, Andrew R; Cornelissen, Gerard

2015-01-01

The sorption of two monoterpenes, α pinene and limonene to the carbonaceous geosorbents graphite, bituminous coal, lignite coke, biochar and Pahokee peat was quantified. Polyethylene (PE) passive samplers were calibrated for the first time for these compounds by determining the PE-water partitioning coefficients and used as a tool to determine sorption to the carbonaceous geosorbents. Log KPE-water values were 3.49±0.58 for α pinene and 4.08±0.27 for limonene. The sorption of limonene to all materials was stronger than that for α pinene (differences of 0.2-1.3 log units between distribution coefficients for the monoterpenes). Placing Kd values in increasing order for α pinene gave biochar≈Pahokee peat≈bituminous coal≈lignite coke

Identification of aggregates for Tennessee bituminous surface courses

NASA Astrophysics Data System (ADS)

Sauter, Heather Jean

Tennessee road construction is a major venue for federal and state spending. Tax dollars each year go to the maintenance and construction of roads. One aspect of highway construction that affects the public is the safety of its state roads. There are many factors that affect the safety of a given road. One factor that was focused on in this research was the polish resistance capabilities of aggregates. Several pre-evaluation methods have been used in the laboratory to predict what will happen in a field situation. A new pre-evaluation method was invented that utilized AASHTO T 304 procedure upscaled to accommodate surface bituminous aggregates. This new method, called the Tennessee Terminal Textural Condition Method (T3CM), was approved by Tennessee Department of Transportation to be used as a pre-evaluation method on bituminous surface courses. It was proven to be operator insensitive, repeatable, and an accurate indication of particle shape and texture. Further research was needed to correlate pre-evaluation methods to the current field method, ASTM E 274-85 Locked Wheel Skid Trailer. In this research, twenty-five in-place bituminous projects and eight source evaluations were investigated. The information gathered would further validate the T3CM and find the pre-evaluation method that best predicted the field method. In addition, new sources of aggregates for bituminous surface courses were revealed. The results of this research have shown T3CM to be highly repeatable with an overall coefficient of variation of 0.26% for an eight sample repeatability test. It was the best correlated pre-evaluation method with the locked wheel skid trailer method giving an R2 value of 0.3946 and a Pearson coefficient of 0.710. Being able to predict field performance of aggregates prior to construction is a powerful tool capable of saving time, money, labor, and possibly lives.

Thermal analysis and kinetics of coal during oxy-fuel combustion

NASA Astrophysics Data System (ADS)

Kosowska-Golachowska, Monika

2017-08-01

The pyrolysis and oxy-fuel combustion characteristics of Polish bituminous coal were studied using non-isothermal thermogravimetric analysis. Pyrolysis tests showed that the mass loss profiles were almost similar up to 870°C in both N2 and CO2 atmospheres, while further mass loss occurred in CO2 atmosphere at higher temperatures due to char-CO2 gasification. Replacement of N2 in the combustion environment by CO2 delayed the combustion of bituminous coal. At elevated oxygen levels, TG/DTG profiles shifted through lower temperature zone, ignition and burnout temperatures decreased and mass loss rate significantly increased and complete combustion was achieved at lower temperatures and shorter times. Kinetic analysis for the tested coal was performed using Kissinger-Akahira-Sunose (KAS) method. The activation energies of bituminous coal combustion at the similar oxygen content in oxy-fuel with that of air were higher than that in air atmosphere. The results indicated that, with O2 concentration increasing, the activation energies decreased.

Reclaimed manufacturer asphalt roofing shingles in asphalt mixtures. Final research report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Reed, A.B.

1999-04-23

The purpose of this project was to pave a test section using hot mix asphalt with roofing shingle pieces in the wearing and binder courses and to evaluate. The test project near Allentown, PA plus two other test projects in 1998 provide evidence of very good pavement performance. The bituminous concrete mix was modified with shredded shingles with a maximum size of 1/2 inch which added 1% of the asphalt content. The Department issued a statewide Provisional Specification titled Reclaimed Manufacturer Asphalt Roofing Shingles in Plant-Mixed Bituminous Concrete Courses'' on March 15, 1999. New manufacturer asphalt roofing shingle scrap includingmore » tab punch-outs can be successfully incorporated in bituminous concrete pavements if the shingles are shredded to 100% passing the 3/4 inch sieve. To take full advantage of the potential to replace a portion of the asphalt and therefore, reduce mix costs, shingles should be shredded to 100% passing minus 1/2 inch sieve.« less

Impact of arterial blood gas analysis in disability evaluation of the bituminous coal miner with simple pneumoconiosis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fields, C.L.; Roy, T.M.; Dow, F.T.

1992-04-01

The Department of Labor has set guidelines for the use of resting arterial blood gas analysis in determination of total and permanent disability for coal workers' pneumoconiosis. To determine the prevalence with which bituminous coal miners fall below the arterial tensions of both oxygen and carbon dioxide published in the Federal Register, we studied 1012 miners who had both reproducible spirometry and arterial blood gas analysis as part of their disability evaluation. Eighty-seven percent of impaired miners could be identified by the spirometric criteria. Thirteen percent of impaired bituminous coal miners had acceptable pulmonary function but were eligible for blackmore » lung benefits by the blood gas guidelines. This population would have been missed if blood gas analysis were excluded from the evaluation process. On the other hand, approximately 25% of the blood gas analyses that were performed could be eliminated if a policy was adopted to do this test only on miners with spirometry that exceed the federal guidelines.« less

Effect of organic calcium compounds on combustion characteristics of rice husk, sewage sludge, and bituminous coal: thermogravimetric investigation.

PubMed

Zhang, Lihui; Duan, Feng; Huang, Yaji

2015-04-01

Experiments were conducted in a thermogravimetric analyzer to assess the enhancement of combustion characteristics of different solid fuels blended with organic calcium compounds (OCCs). Rice husk, sewage sludge, and bituminous coal, and two OCC were used in this study. Effect of different mole ratios of calcium to sulfur (Ca/S ratio) on the combustion characteristics were also investigated. Results indicated that combustion performance indexes for bituminous coal impregnated by OCC were improved, however, an inverse trend was found for sewage sludge because sewage sludge has lower ignition temperature and higher volatile matter content compared to those of OCC. For rice husk, effect of added OCC on the combustion characteristics is not obvious. Different solid fuels show different combustion characteristics with increases of Ca/S ratio. The maximum combustion performance indexes appear at Ca/S ratios of 1:1, 2:1, and 3:1 for OCC blended with Shenhua coal, rice husk, and sewage sludge, respectively. Copyright © 2015 Elsevier Ltd. All rights reserved.

Experimental and computational study and development of the bituminous coal entrained-flow air-blown gasifier for IGCC

NASA Astrophysics Data System (ADS)

Abaimov, N. A.; Osipov, P. V.; Ryzhkov, A. F.

2016-10-01

In the paper the development of the advanced bituminous coal entrained-flow air- blown gasifier for the high power integrated gasification combined cycle is considered. The computational fluid dynamics technique is used as the basic development tool. The experiment on the pressurized entrained-flow gasifier was performed by “NPO CKTI” JSC for the thermochemical processes submodel verification. The kinetic constants for Kuznetsk bituminous coal (flame coal), obtained by thermal gravimetric analysis method, are used in the model. The calculation results obtained by the CFD model are in satisfactory agreements with experimental data. On the basis of the verified model the advanced gasifier structure was suggested which permits to increase the hydrogen content in the synthesis gas and consequently to improve the gas turbine efficiency. In order to meet the specified requirements vapor is added on the second stage of MHI type gasifier and heat necessary for air gasification is compensated by supplemental heating of the blasting air.

Co-combustion characteristics and blending optimization of tobacco stem and high-sulfur bituminous coal based on thermogravimetric and mass spectrometry analyses.

PubMed

Zhang, Kaihua; Zhang, Kai; Cao, Yan; Pan, Wei-ping

2013-03-01

Despite much research on co-combustion of tobacco stem and high-sulfur coal, their blending optimization has not been effectively found. This study investigated the combustion profiles of tobacco stem, high-sulfur bituminous coal and their blends by thermogravimetric analysis. Ignition and burnout performances, heat release performances, and gaseous pollutant emissions were also studied by thermogravimetric and mass spectrometry analyses. The results indicated that combustion of tobacco stem was more complicated than that of high-sulfur bituminous coal, mainly shown as fixed carbon in it was divided into two portions with one early burning and the other delay burning. Ignition and burnout performances, heat release performances, and gaseous pollutant emissions of the blends present variable trends with the increase of tobacco stem content. Taking into account the above three factors, a blending ratio of 0–20% tobacco stem content is conservatively proposed as optimum amount for blending. Copyright © 2012 Elsevier Ltd. All rights reserved.

Co-pyrolysis characteristic of biomass and bituminous coal.

PubMed

Li, Shuaidan; Chen, Xueli; Liu, Aibin; Wang, Li; Yu, Guangsuo

2015-03-01

Co-pyrolysis characteristics of biomass and bituminous coal have been studied in this work. The temperature was up to 900°C with the heating rates of 10, 15, 20, 25 and 30°C/min. Rice straw, saw dust, microcrystalline cellulose, lignin and Shenfu bituminous coal were chosen as samples. Six different biomass ratios were used. The individual thermal behavior of each sample was obtained. The experimental weight fractions of the blended samples and the calculated values were compared. The results show that the weight fractions of the blended samples behave differently with calculated ones during the co-pyrolysis process. With the increasing biomass ratio, relative deviations between experimental weight fractions and calculated ones are larger. H/C molar ratio, heat transfer properties of biomass would affect to the interaction between biomass and coal. The maximum degradation rates are slower than the calculated ones. The activation energy distributions also changed by adding some biomass into coal. Copyright © 2014 Elsevier Ltd. All rights reserved.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Young, B.C.; Musich, M.A.

A fixed-bed reactor system with continuous Hg{sup 0} analysis capabilities was used to evaluate commercial carbon sorbents for the removal of elemental mercury from simulated flue gas. The objectives of the program were to compare the sorbent effectiveness under identical test conditions and to identify the effects of various flue gas components on elemental mercury sorption. Sorbents tested included steam-activated lignite, chemical-activated hardwood and bituminous coal, iodated steam-activated coconut shell, and sulfur-impregnated steam-activated bituminous coal. The iodated carbon was the most effective carbon, showing over 99% mercury removal according to EPA Method 101A. Data indicate that O{sub 2} (4 vol%)more » and SO{sub 2} (500 ppm) improved the mercury removal of the other carbons for tests at 150{degrees}C using 100 {mu}g/m{sup 3} Hg{sup 0}. Further, the presence of HCl (at 50 ppm) produced a magnitude increase in mercury removal for the steam-activated and sulfur-impregnated bituminous coal-based carbons.« less

Co-combustion of tannery sludge in a commercial circulating fluidized bed boiler.

PubMed

Dong, Hao; Jiang, Xuguang; Lv, Guojun; Chi, Yong; Yan, Jianhua

2015-12-01

Co-combusting hazardous wastes in existing fluidized bed combustors is an alternative to hazardous waste treatment facilities, in shortage in China. Tannery sludge is a kind of hazardous waste, considered fit for co-combusting with coal in fluidized bedboilers. In this work, co-combustion tests of tannery sludge and bituminous coal were conducted in a power plant in Jiaxing, Zhejiang province. Before that, the combustion behavior of tannery sludge and bituminous were studied by thermogravimetric analysis. Tannery sludge presented higher reactivity than bituminous coal. During the co-combustion tests, the emissions of harmful gases were monitored. The results showed that the pollutant emissions met the Chinese standard except for NOx. The Concentrations of seven trace elements (As, Cr, Cd, Ni, Cu, Pb, Mn) in three exit ash flows (bottom ash in bed, fly ash in filter, and submicrometer aerosol in flue gas) were analyzed. The results of mono-combustion of bituminous coal were compared with those of co-combustion with tannery sludge. It was found that chromium enriched in fly ash. At last, the leachability of fly ash and bottom ash was analyzed. The results showed that most species were almost equal to or below the limits except for As in bottom ashes and Cr in the fly ash of co-combustion test. The concentrations of Cr in leachates of co-combustion ashes are markedly higher than that of coal mono-combustion ashes. Copyright © 2015 Elsevier Ltd. All rights reserved.

Routine Testing of Bitumen Binders

NASA Astrophysics Data System (ADS)

Holý, Michal; Remišová, Eva

2017-12-01

The quality of bituminous binders used in the construction and maintenance of road surfaces is currently assessed by empirical testing based on obtaining one value for specific boundary conditions, which were designed about 100 years ago. Basic empirical tests include the softening point and penetration, but the practice shows that these tests appear to be inadequate. The evaluation of changes of bitumen properties during the production and paving process of bituminous mixture is also important. The paper points out how the "traditional" tests as softening point and penetration and viscosity are sufficient to evaluate properties of bitumen binders.

Development of clean coal and clean soil technologies using advanced agglomeration techniques

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ignasiak, B.; Ignasiak, T.; Szymocha, K.

1990-01-01

Three major topics are discussed in this report: (1) Upgrading of Low Rank Coals by the Agflotherm Process. Test data, procedures, equipment, etc., are described for co-upgrading of subbituminous coals and heavy oil; (2) Upgrading of Bituminous Coals by the Agflotherm Process. Experimental procedures and data, bench and pilot scale equipments, etc., for beneficiating bituminous coals are described; (3) Soil Clean-up and Hydrocarbon Waste Treatment Process. Batch and pilot plant tests are described for soil contaminated by tar refuse from manufactured gas plant sites. (VC)

Adsorption of SO2 on bituminous coal char and activated carbon fiber prepared from phenol formaldehyde

USGS Publications Warehouse

DeBarr, Joseph A.; Lizzio, Anthony A.; Daley, Michael A.

1996-01-01

Carbon-based materials are used commercially to remove SO2 from coal combustion flue gases. Historically, these materials have consisted of granular activated carbons prepared from lignite or bituminous coal. Recent studies have reported that activated carbon fibers (ACFs) may have potential in this application due to their relatively high SO2 adsorption capacity. In this paper, a comparison of SO2 adsorption for both coal-based carbons and ACFs is presented, as well as ideas on carbon properties that may influence SO2 adsorption

Time dependent viscoelastic rheological response of pure, modified and synthetic bituminous binders

NASA Astrophysics Data System (ADS)

Airey, G. D.; Grenfell, J. R. A.; Apeagyei, A.; Subhy, A.; Lo Presti, D.

2016-08-01

Bitumen is a viscoelastic material that exhibits both elastic and viscous components of response and displays both a temperature and time dependent relationship between applied stresses and resultant strains. In addition, as bitumen is responsible for the viscoelastic behaviour of all bituminous materials, it plays a dominant role in defining many of the aspects of asphalt road performance, such as strength and stiffness, permanent deformation and cracking. Although conventional bituminous materials perform satisfactorily in most highway pavement applications, there are situations that require the modification of the binder to enhance the properties of existing asphalt material. The best known form of modification is by means of polymer modification, traditionally used to improve the temperature and time susceptibility of bitumen. Tyre rubber modification is another form using recycled crumb tyre rubber to alter the properties of conventional bitumen. In addition, alternative binders (synthetic polymeric binders as well as renewable, environmental-friendly bio-binders) have entered the bitumen market over the last few years due to concerns over the continued availability of bitumen from current crudes and refinery processes. This paper provides a detailed rheological assessment, under both temperature and time regimes, of a range of conventional, modified and alternative binders in terms of the materials dynamic (oscillatory) viscoelastic response. The rheological results show the improved viscoelastic properties of polymer- and rubber-modified binders in terms of increased complex shear modulus and elastic response, particularly at high temperatures and low frequencies. The synthetic binders were found to demonstrate complex rheological behaviour relative to that seen for conventional bituminous binders.

Nonspecific airway hyperreactivity in nonsmoking bituminous coal miners demonstrated by quantitative methacholine inhalation challenge

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hudgel, D.W.; Roe, R.

Because nonsmoking underground bituminous coal miners often have symptoms of chronic bronchitis and because a high proportion of patients with chronic bronchitis have nonspecific airway hyperreactivity, we hypothesized that coal miners would have a higher prevalence of nonspecific airway hyperreactivity than nonminer nonsmoking control subjects. By use of a quantitative methacholine provocative inhalation challenge test, we evaluated 22 underground bituminous coal miners and 41 nonminer age- and sex-matched control subjects from the same community. We found that a significantly higher proportion of miners had reactivity to inhalation of 100 mg/ml or less of methacholine, X2 = 6.19, p less thanmore » 0.02. The slope of phase III of the single-breath nitrogen washout test was higher in the reactive miners than in the nonreactive miners and reactive control subjects, even though the reactive miners had only been working underground 8 +/- 3 (SEM) years. Within the reactive miner subgroup, the higher the reactivity to methacholine, the more abnormal the slope of phase III of the single-breath nitrogen test, r = 0.79. Miners had more symptoms than controls; the presence of methacholine reactivity was not associated with increased symptoms. We conclude that the bituminous coal miners in our study had an increased prevalence of nonspecific airway hyperreactivity and that within the reactive miner subgroup there was evidence of early airways disease. We speculate that the nonspecific airway hyperreactivity may be related to, and also be an indicator of, lung injury in coal miners.« less

Rutting performance of cold bituminous emulsion mixtures

NASA Astrophysics Data System (ADS)

Arshad, Ahmad Kamil; Ali, Noor Azilatom; Shaffie, Ekarizan; Hashim, Wardati; Rahman, Zanariah Abd

2017-10-01

Cold Bituminous Emulsion Mixture (CBEM) is an environmentally friendly alternative to hot mix asphalt (HMA) for road surfacing, due to its low energy requirements. However, CBEM has generally been perceived to be less superior in performance, compared to HMA. This paper details a laboratory study on the rutting performance of CBEM. The main objective of this study is to determine the Marshall properties of CBEM and to evaluate the rutting performance. The effect of cement in CBEM was also evaluated in this study. The specimens were prepared using Marshall Mix Design Method and rutting performance was evaluated using the Asphalt Pavement Analyzer (APA). Marshall Properties were analysed to confirm compliance with the PWD Malaysia's specification requirements. The rutting performance for specimens with cement was also found to perform better than specimens without cement. It can be concluded that Cold Bituminous Emulsion Mixtures (CBEM) with cement is a viable alternative to Hot Mix Asphalt (HMA) as their Marshall Properties and performance obtained from this study meets the requirements of the specifications. It is recommended that further study be conducted on CBEM for other performance criteria such as moisture susceptibility and fatigue.

Geochemistry of radioactive elements in bituminous sands and sandstones of Permian bitumen deposits of Tatarstan (east of the Russian plate)

NASA Astrophysics Data System (ADS)

Mullakaev, A. I.; Khasanov, R. R.; Badrutdinov, O. R.; Kamaletdinov, I. R.

2018-05-01

The article investigates geochemical features of Permian (Cisuralian, Ufimian Stage and Biarmian, Kazanian Stage of the General Stratigraphic Scale of Russia) bituminous sands and sandstones located on the territory of the Volga-Ural oil and gas province (Republic of Tatarstan). Natural bitumens are extracted using thermal methods as deposits of high-viscosity oils. In the samples studied, the specific activity of natural radionuclides from the 238U (226Ra), 232Th, and 40K series was measured using gamma spectrometry. As a result of the precipitation of uranium and thorium and their subsequent decay, the accumulation of radium (226Ra and 228Ra) has been shown to occur in the bituminous substance. In the process of exploitation of bitumen-bearing rock deposits (as an oil fields) radium in the composition of a water-oil mixture can be extracted to the surface or deposited on sulfate barriers, while being concentrated on the walls of pipes and other equipment. This process requires increased attention to monitoring and inspection the environmental safety of the exploitation procedure.

Design of a bituminous mixture for perpetual pavement

NASA Astrophysics Data System (ADS)

Gireesh Kumar, S.; Satya, J.; Mittal, Kratagya; Raju, Sridhar

2018-03-01

The flexible pavements with a design period of 50 years without requiring major structural rehabilitation and reconstructions are called as perpetual pavements. The present study aims at designing a high modulus Dense Bituminous Macadam (DBM) mixture for perpetual pavements using Industrial Grade (IG) bitumen in combination with Viscosity Grade (VG30) bitumen. Various blending combinations were tried and the ratio of 70:30 for IG: VG30 was found to fulfill the requirements. The modified Marshall hammer was used for the preparation of specimens, as the nominal size of aggregate was 25 mm. A comparative study on DBM mixture with VG30 alone and with IG: VG30 (70:30) was done and the Optimum Binder Contents obtained were 5.0 % and 5.3 % respectively at 4 % air voids. The water sensitivity tests were carried out on the bituminous specimens in accordance with AASHTO T 283 and the Indirect Tensile Strength (ITS) ratio obtained were 80.0 % and 98.3 % respectively for specimens with VG30 and IG: VG30. The stiffness modulus of DBM specimens with IG: VG30 bitumen was 3 times higher than DBM with VG30 bitumen.

Organic emissions from coal pyrolysis: mutagenic effects.

PubMed Central

Braun, A G; Wornat, M J; Mitra, A; Sarofim, A F

1987-01-01

Four different types of coal have been pyrolyzed in a laminar flow, drop tube furnace in order to establish a relationship between polycyclic aromatic compound (PAC) evolution and mutagenicity. Temperatures of 900K to 1700K and particle residence times up to 0.3 sec were chosen to best simulate conditions of rapid rate pyrolysis in pulverized (44-53 microns) coal combustion. The specific mutagenic activity (i.e., the activity per unit sample weight) of extracts from particulates and volatiles captured on XAD-2 resin varied with coal type according to the order: subbituminous greater than high volatile bituminous greater than lignite greater than anthracite. Total mutagenic activity (the activity per gram of coal pyrolyzed), however, varied with coal type according to the order: high volatile bituminous much greater than subbituminous = lignite much greater than anthracite, due primarily to high organic yield during high volatile bituminous coal pyrolysis. Specific mutagenic activity peaked in a temperature range of 1300K to 1500K and generally appeared at higher temperatures and longer residence times than peak PAC production. PMID:3311724

Improvement of Life Expectancy of Jute Based Needlepunched Geotextiles Through Bitumen Treatment

NASA Astrophysics Data System (ADS)

Ghosh, S. K.; Ray Gupta, K.; Bhattacharyya, R.; Sahu, R. B.; Mandol, S.

2014-12-01

Geotextiles have witnessed unrivalled growth worldwide in recent years in the field of different civil engineering constructions. The world of Geotextiles includes mainly non-biodegradable synthetic materials which are not environmentally compatible. With the increasing human awareness on environmental pollution aspects, biodegradable Jute Geotextile is increasingly gaining ground over its synthetic non-biodegradable counterpart. Though Jute is advantageous for its complete biodegradability in one hand but on the other hand it is disadvantageous for its poor microbial resistance and quicker biodegradation particularly under moist soil conditions, when applied as Geotextiles under soil. Therefore, it is a great challenge to the present researchers to make jute more microbial resistant (rot resistant) keeping its biodegradability intact during its performance period. Thorough investigation and study regarding the improvement of the durability of natural Jute Geotextile reveals the fact that though several attempts including chemical treatments have been made to enhance the life expectancy of jute fabrics yet these methods were neither found to be suitable nor techno-economically viable. Therefore, in order to accomplish the objective and based on the researchers' report of satisfactory thermal compatibility between hot bitumen and jute nonwoven fabrics, in the present study Bitumen emulsion with essential additives has been applied following a special technique, apart from the conventional method, on the Grey Jute Nonwoven Fabrics in different add on percentages to make a comparative assessment of the performance of both Grey Jute Fabrics and Bituminized Jute Nonwoven Fabrics by Soil Burial Test as per the BIS standard test method. The test results revealed that the durability and performance of the Bituminized Nonwoven Jute Fabrics are much better than that of Grey Jute Nonwoven Fabrics.

Nuclear magnetic resonance studies of ancient buried wood-II. Observations on the origin of coal from lignite to bituminous coal

USGS Publications Warehouse

Hatcher, P.G.; Breger, I.A.; Szeverenyi, N.; Maciel, G.E.

1982-01-01

Coalified logs ranging in age from Late Pennsylvania to Miocene and in rank from lignite B to bituminous coal were analyzed by 13C nuclear magnetic resonance (NMR) utilizing the cross-polarization, magic-angle spinning technique, as well as by infrared spectroscopy. The results of this study indicate that at least three major stages of coalification can be observed as wood gradually undergoes transformation to bituminous coal. The first stage involves hydrolysis and loss of cellulose from wood with retention and differential concentration of the resistant lignin. The second stage involves conversion of the lignin residues directly to coalified wood of lignitic rank, during which the oxygen content of intermediate diagenetic products remains constant as the hydrogen content and the carbon content increases. These changes are thought to involve loss of methoxyl groups, water, and C3 side chains from the lignin. In the third major stage of coalification, the coalified wood increases in rank to subbituminous and bituminous coal; during this stage the oxygen content decreases, hydrogen remains constant, and the carbon content increases. These changes are thought to result from loss of soluble humic acids that are rich in oxygen and that are mobilized during compaction and dewatering. Relatively resistant resinous substances are differentially concentrated in the coal during this stage. The hypothesis that humic acids are formed as mobile by-products of the coalification of lignin and function only as vehicles for removal of oxygen represents a dramatic departure from commonly accepted views that they are relatively low-molecular-weight intermediates formed during the degradation of lignin that then condense to form high-molecular-weight coal structures. ?? 1982.

Distribution of trace elements in selected pulverized coals as a function of particle size and density

USGS Publications Warehouse

Senior, C.L.; Zeng, T.; Che, J.; Ames, M.R.; Sarofim, A.F.; Olmez, I.; Huggins, Frank E.; Shah, N.; Huffman, G.P.; Kolker, A.; Mroczkowski, S.; Palmer, C.; Finkelman, R.

2000-01-01

Trace elements in coal have diverse modes of occurrence that will greatly influence their behavior in many coal utilization processes. Mode of occurrence is important in determining the partitioning during coal cleaning by conventional processes, the susceptibility to oxidation upon exposure to air, as well as the changes in physical properties upon heating. In this study, three complementary methods were used to determine the concentrations and chemical states of trace elements in pulverized samples of four US coals: Pittsburgh, Illinois No. 6, Elkhorn and Hazard, and Wyodak coals. Neutron Activation Analysis (NAA) was used to measure the absolute concentration of elements in the parent coals and in the size- and density-fractionated samples. Chemical leaching and X-ray absorption fine structure (XAFS) spectroscopy were used to provide information on the form of occurrence of an element in the parent coals. The composition differences between size-segregated coal samples of different density mainly reflect the large density difference between minerals, especially pyrite, and the organic portion of the coal. The heavy density fractions are therefore enriched in pyrite and the elements associated with pyrite, as also shown by the leaching and XAFS methods. Nearly all the As is associated with pyrite in the three bituminous coals studied. The sub-bituminous coal has a very low content of pyrite and arsenic; in this coal arsenic appears to be primarily organically associated. Selenium is mainly associated with pyrite in the bituminous coal samples. In two bituminous coal samples, zinc is mostly in the form of ZnS or associated with pyrite, whereas it appears to be associated with other minerals in the other two coals. Zinc is also the only trace element studied that is significantly more concentrated in the smaller (45 to 63 ??m) coal particles.

Review and environmental impact assessment of green technologies for base courses in bituminous pavements

DOE Office of Scientific and Technical Information (OSTI.GOV)

Anthonissen, Joke, E-mail: joke.anthonissen@uantwerpen.be; Van den bergh, Wim, E-mail: wim.vandenbergh@uantwerpen.be; Braet, Johan, E-mail: johan.braet@uantwerpen.be

This paper provides a critical review of different approaches applied in the Belgian asphalt sector in order to reduce the environmental impact of bituminous road construction works. The focus is on (1) reusing reclaimed asphalt pavement, (2) reducing the asphalt production temperature, and (3) prolonging the service life of the pavement. Environmental impact assessment of these methods is necessary to be able to compare these approaches and understand better the ability to reduce the environmental impact during the life cycle of the road pavement. Attention should be drawn to the possible shift in environmental impact between various life cycle stages,more » e.g., raw material production, asphalt production, or waste treatment. Life cycle assessment is necessary to adequately assess the environmental impact of these approaches over the entire service life of the bituminous pavement. The three approaches and their implementation in the road sector in Flanders (region in Belgium) are described and the main findings from life cycle assessment studies on these subjects are discussed. It was found from the review that using reclaimed asphalt pavement in new bituminous mixtures might yield significant environmental gains. The environmental impact of the application of warm mix asphalt technologies, on the other hand, depends on the technique used. - Highlights: • Recycling, lower production temperature and durability of asphalt are investigated. • The use of RAP in new asphalt mixtures yields significant environmental advantages. • It would be beneficial to allow RAP in asphalt mixtures for wearing courses. • The use of particular additives might counteract the environmental gain from WMA. • The service life and the environmental data source influence the LCA results.« less

Pelletizing lignite

DOEpatents

Goksel, Mehmet A.

1983-11-01

Lignite is formed into high strength pellets having a calorific value of at least 9,500 Btu/lb by blending a sufficient amount of an aqueous base bituminous emulsion with finely-divided raw lignite containing its inherent moisture to form a moistened green mixture containing at least 3 weight % of the bituminous material, based on the total dry weight of the solids, pelletizing the green mixture into discrete green pellets of a predetermined average diameter and drying the green pellets to a predetermined moisture content, preferrably no less than about 5 weight %. Lignite char and mixture of raw lignite and lignite char can be formed into high strength pellets in the same general manner.

Chemical activation of bituminous coal for hampering oligomerization of organic contaminants.

PubMed

Yan, Liang; Sorial, George A

2011-12-15

Activated carbons prepared by KOH activation of bituminous coal were studied for hampering oligomerization of phenolic compounds on its surface. A total of 24 activated carbons with different microporosity and BET surface area were created. The effect of the different variables of the activation process (KOH/bituminous coal ratio, heating temperature, activation time, and flow rate of nitrogen gas) on critical carbon parameters was analyzed. The impact of activated carbon on oligomerization was examined by conducting isotherm experiments at a neutral pH on Carbon(exp) produced with optimal characteristics and granular activated carbon (GAC) F400 for phenol, 2-methylphenol and 2-ethylphenol. These isotherms were collected under anoxic (absence of molecular oxygen) and oxic (presence of molecular oxygen) conditions. The single solute adsorption of phenol, 2-methylphenol and 2-ethylphenol on Carbon(exp) showed no obvious differences between oxic and anoxic environment, which indicated that the Carbon(exp) sample is very effective in hampering the oligomerization of phenolic compounds under oxic conditions. On the other hand, F400, which have lower micropore percentage and BET surface area, significant increases in the adsorptive capacity had been observed when molecular oxygen was present. Copyright © 2011 Elsevier B.V. All rights reserved.

Petrographic and Vitrinite Reflectance Analyses of a Suite of High Volatile Bituminous Coal Samples from the United States and Venezuela

USGS Publications Warehouse

Hackley, Paul C.; Kolak, Jonathan J.

2008-01-01

This report presents vitrinite reflectance and detailed organic composition data for nine high volatile bituminous coal samples. These samples were selected to provide a single, internally consistent set of reflectance and composition analyses to facilitate the study of linkages among coal composition, bitumen generation during thermal maturation, and geochemical characteristics of generated hydrocarbons. Understanding these linkages is important for addressing several issues, including: the role of coal as a source rock within a petroleum system, the potential for conversion of coal resources to liquid hydrocarbon fuels, and the interactions between coal and carbon dioxide during enhanced coalbed methane recovery and(or) carbon dioxide sequestration in coal beds.

Basic magnetic properties of bituminous coal

USGS Publications Warehouse

Alexander, C.C.; Thorpe, A.N.; Senftle, F.E.

1979-01-01

Magnetic susceptibility and other static magnetic parameters have been measured on a number of bituminous coals from various locations in the United States. The paramagnetic Curie constant correlates negatively with carbon concentration on a moisture-free basis. The major contribution to the total paramagnetism comes from the mineral matter rather than from free radicals or broken bonds. Analysis of the data indicates that the specific paramagnetism is generally lower in the mineral matter found in high-ash compared to low-ash coal. A substantial number of the coal specimens tested also had a ferromagnetic susceptibility which appeared to be associated with magnetite. Magnetite and ??-iron spherules, possibly of meteoritic or volcanic origin, were found in several specimens. ?? 1979.

Particle size distribution of fly ash from co-incineration of bituminous coal with municipal solid waste

NASA Astrophysics Data System (ADS)

Cieślik, Ewelina; Konieczny, Tomasz; Bobik, Bartłomiej

2018-01-01

One of the source of air pollutants is emission from local coal-fired boiler-houses and domestic heating boilers. The consequence of incineration of municipal waste is the introduction of additional pollutants into the atmosphere, including fly ash. The aim of this work was to evaluate the particle size distribution of fly ash emitted by coal combustion and co-incineration of coal with municipal waste in a domestic 18 kW central heating boiler equipped with an automatic fuel feeder. Mixtures of bituminous coal with different types of solid waste (5, 10 and 15% of mass fraction) were used. Solid waste types consisted of: printed, colored PE caps, fragmented cable trunking, fragmented car gaskets and shredded tires from trucks. During the incineration of a given mixture of municipal waste with bituminous coal, the velocity of exhaust gas was specified, the concentration and mass flow of fly ash were determined together with the physico-chemical parameters of the exhaust gas, the samples of emitted fly ash were taken as the test material. Particle size analysis of fly ash was performed using laser particle sizer Fritch Analysette 22. The PM10 share from all fly ashes from incineration of mixtures was about 100%. Differences were noted between PM2.5 and PM1.

Asphalt mixtures with a high amount of RAP - case study

NASA Astrophysics Data System (ADS)

Koudelka, Tomas; Varaus, Michal

2017-09-01

A case study of one trial section in the Pilsen region is presented. The pavement in the section was newly constructed in 2015 using one type of an asphalt concrete mixtures with varying RAP content. The constructed surface course comprises of 0% to 50% RAP. In order to restore the aged binder properties and to avoid the embrittlement of the produced mixtures, a rubber-based modifier/rejuvenator was employed. For technological reasons during manufacturing processes, which engage a parallel drying drum, a crude oil-based rejuvenator was also added. This article contains the preliminary data from an on-going project focused on monitoring the properties of bituminous binders contained in asphalt mixtures. The actual bituminous binders were extracted straight after production, after 6 months and after 12 months. The binder characteristics are evaluated using empirical testing as well as functional tests. Low temperature properties are measured by a Bending Beam Rheometer (BBR). The preliminary results show, that the bituminous binders properties change significantly in a relatively short period of time. The progress in binder’ characteristics is contradictory to up-to date knowledge. The probability that the phenomenon of diffusion between aged binder and rejuvenator agents occurs exists. Moreover, the data might indicate that the process of rejuvenator evaporation takes place.

Natural radioactivity of the tar-sand deposits of Ondo State, Southwestern Nigeria

NASA Astrophysics Data System (ADS)

Fasasi, M. K.; Oyawale, A. A.; Mokobia, C. E.; Tchokossa, P.; Ajayi, T. R.; Balogun, F. A.

2003-06-01

A combination of gamma spectrometry and energy dispersive X-ray fluorescence was used to determine the presence and level of radioactivity of radionuclides in bituminous sand and overburden obtained from bituminous sand deposits in Ondo State Nigeria for the purpose of providing baseline data and assessing its impact on the environment. The radionuclides identified with reliable regularity belong to the decay series of naturally occurring radionuclides headed by 238U and 232Th. The non-decay series of naturally occurring 40K was found to be below the limit of detection. The average specific activity concentration values obtained for 214 Bi, 208Tl, and 226Ra in the overburden are 165.64±2.91, 150.25±2.91 and 60.97±2.27 Bq kg -1, respectively. The measured activity in the bituminous sand layer is so low that it can be said to be non-radioactive. The result of the EDXRF supports the presence of radioelements in the overburden, which are likely to be embedded in accessory minerals like zircon and tourmaline. Thus, surface exploration technique using soil-gas radon measurement will not yield the desired result. Furthermore, the level of radioelements and associated decay daughter 222Rn is not expected to cause any health hazard.

Characterization of Gas-Phase Organics Using Proton Transfer Reaction Time-of-Flight Mass Spectrometry: Residential Coal Combustion.

PubMed

Klein, Felix; Pieber, Simone M; Ni, Haiyan; Stefenelli, Giulia; Bertrand, Amelie; Kilic, Dogushan; Pospisilova, Veronika; Temime-Roussel, Brice; Marchand, Nicolas; El Haddad, Imad; Slowik, Jay G; Baltensperger, Urs; Cao, Junji; Huang, Ru-Jin; Prévôt, André S H

2018-03-06

Residential coal combustion is a significant contributor to particulate urban air pollution in Chinese mega cities and some regions in Europe. While the particulate emission factors and the chemical characteristics of the organic and inorganic aerosol from coal combustion have been extensively studied, the chemical composition and nonmethane organic gas (NMOG) emission factors from residential coal combustion are mostly unknown. We conducted 23 individual burns in a traditional Chinese stove used for heating and cooking using five different coals with Chinese origins, characterizing the NMOG emissions using a proton transfer reaction time-of-flight mass spectrometer. The measured emission factors range from 1.5 to 14.1 g/kg coal for bituminous coals and are below 0.1 g/kg coal for anthracite coals. The emission factors from the bituminous coals are mostly influenced by the time until the coal is fully ignited. The emissions from the bituminous coals are dominated by aromatic and oxygenated aromatic compounds with a significant contribution of hydrocarbons. The results of this study can help to improve urban air pollution modeling in China and Eastern Europe and can be used to constrain a coal burning factor in ambient gas phase positive matrix factorization studies.

Bituminization of radioactive wastes: safety studies

DOE Office of Scientific and Technical Information (OSTI.GOV)

Arod, J.

1982-01-01

The bitumen embedding of low- and medium-level radioactive wastes has reached the industrial stage. Bituminization plants are operating satisfactorily in France and throughout the world. However, bituminization presents certain risks due to the nature of bitumens themselves. These risks must be taken into account. This paper specifies those risks and presents the results of leachability tests performed in accordance with the International Atomic Energy Agency proposed standard on coated concentrates, on chemical coprecipitation sludges with and without addition of heavy solvents such as TBP and TLA, and on ion exchange resins. The results show that the leaching rates in demineralizedmore » water are on the order of 10/sup -6/ to 10/sup -8/ for cesium 137, 10/sup -5/ to 10/sup -7/ for strontium-90, 10/sup -5/ to 10/sup -6/ for ruthemium-106, 10/sup -5/ to 10/sup -6/ for cobalt-60, 10/sup -5/ to 10/sup -6/ for total gamma activity, and 10/sup -5/ to 10/sup -8/ for the plutonium-238, the plutonium-239, and the americium 241 alpha emitters. Even if this conditioning is not perfect, the storage of low- and medium-level radioactive wastes is made possible with adequate safety and at a reasonable cost.« less

Field Testing of a Wet FGD Additive for Enhanced Mercury Control - Pilot-Scale Test Results

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gary M. Blythe

2006-03-01

This Topical Report summarizes progress on Cooperative Agreement DE-FC26-04NT42309, ''Field Testing of a Wet FGD Additive.'' The objective of the project is to demonstrate the use of a flue gas desulfurization (FGD) additive, Degussa Corporation's TMT-15, to prevent the reemissions of elemental mercury (Hg{sup 0}) in flue gas exiting wet FGD systems on coal-fired boilers. Furthermore, the project intends to demonstrate that the additive can be used to precipitate most of the mercury (Hg) removed in the wet FGD system as a fine TMT salt that can be separated from the FGD liquor and bulk solid byproducts for separate disposal.more » The project will conduct pilot and full-scale tests of the TMT-15 additive in wet FGD absorbers. The tests are intended to determine required additive dosage requirements to prevent Hg{sup 0} reemissions and to separate mercury from the normal FGD byproducts for three coal types: Texas lignite/Power River Basin (PRB) coal blend, high-sulfur Eastern bituminous coal, and low-sulfur Eastern bituminous coal. The project team consists of URS Group, Inc., EPRI, TXU Generation Company LP, Southern Company, and Degussa Corporation. TXU Generation has provided the Texas lignite/PRB co-fired test site for pilot FGD tests, Monticello Steam Electric Station Unit 3. Southern Company is providing the low-sulfur Eastern bituminous coal host site for wet scrubbing tests, as well as the pilot and full-scale jet bubbling reactor (JBR) FGD systems to be tested. A third utility, to be named later, will provide the high-sulfur Eastern bituminous coal full-scale FGD test site. Degussa Corporation is providing the TMT-15 additive and technical support to the test program. The project is being conducted in six tasks. Of the six project tasks, Task 1 involves project planning and Task 6 involves management and reporting. The other four tasks involve field testing on FGD systems, either at pilot or full scale. The four tasks include: Task 2 - Pilot Additive Testing in Texas Lignite Flue Gas; Task 3 - Full-scale FGD Additive Testing in High Sulfur Eastern Bituminous Flue Gas; Task 4 - Pilot Wet Scrubber Additive Tests at Yates; and Task 5 - Full-scale Additive Tests at Plant Yates. This topical report presents the results from the Task 2 and Task 4 pilot-scale additive tests. The Task 3 and Task 5 full-scale additive tests will be conducted later in calendar year 2006.« less

Fuel Flexibility in Gasification

DOE Office of Scientific and Technical Information (OSTI.GOV)

McLendon, T. Robert; Pineault, Richard L.; Richardson, Steven W.

2001-11-06

In order to increase efficiencies of carbonizers, operation at high pressures is needed. In addition, waste biomass fuels of opportunity can be used to offset fossil fuel use. The National Energy Technology Laboratory (NETL) Fluidized Bed Gasifier/Combustor (FBG/C) was used to gasify coal and mixtures of coal and biomass (sawdust) at 425 psig. The purpose of the testing program was to generate steady state operating data for modeling efforts of carbonizers. A test program was completed with a matrix of parameters varied one at a time in order to avoid second order interactions. Variables were: coal feed rate, pressure, andmore » varying mixtures of sawdust and coal types. Coal types were Montana Rosebud subbituminous and Pittsburgh No. 8 bituminous. The sawdust was sanding waste from a furniture manufacturer in upstate New York. Coal was sieved from -14 to +60 mesh and sawdust was sieved to -14 mesh. The FBG/C operates at a nominal 425 psig, but pressures can be lowered. For the tests reported it was operated as a jetting, fluidized bed, ash-agglomerating gasifier. Preheated air and steam are injected into the center of the bottom along with the solid feed that is conveyed with cool air. Fairly stable reactor internal flow patterns develop and temperatures stabilize (with some fluctuations) when steady state is reached. At nominal conditions the solids residence time in the reactor is on the order of 1.5 to 2 hours, so changes in feed types can require on the order of hours to equilibrate. Changes in operating conditions (e.g. feed rate) usually require much less time. The operating periods of interest for these tests were only the steady state periods, so transient conditions were not monitored as closely. The test matrix first established a base case of operations to which single parameter changes in conditions could be compared. The base case used Montana Rosebud at a coal feed rate of 70 lbm/hr at 425 psig. The coal sawdust mixtures are reported as percent by weight coal to percent by weight sawdust. The mixtures of interest were: 65/35 subbituminous, 75/25 subbituminous, 85/15 subbituminous, and 75/25 bituminous. Steady state was achieved quickly when going from one subbituminous mixture to another, but longer when going from subbituminous to bituminous coal. The most apparent observation when comparing the base case to subbituminous coal/sawdust mixtures is that operating conditions are nearly the same. Product gas does not change much in composition and temperatures remain nearly the same. Comparisons of identical weight ratios of sawdust and subbituminous and bituminous mixtures show considerable changes in operating conditions and gas composition. The highly caking bituminous coal used in this test swelled up and became about half as dense as the comparable subbituminous coal char. Some adjustments were required in accommodating changes in solids removal during the test. Nearly all the solids in the bituminous coal sawdust were conveyed into the upper freeboard section and removed at the mid-level of the reactor. This is in marked contrast to the ash-agglomerating condition where most solids are removed at the very bottom of the gasifier. Temperatures in the bottom of the reactor during the bituminous test were very high and difficult to control. The most significant discovery of the tests was that the addition of sawdust allowed gasification of a coal type that had previously resulted in nearly instant clinkering of the gasifier. Several previous attempts at using Pittsburgh No. 8 were done only at the end of the tests when shutdown was imminent anyway. It is speculated that the fine wood dust somehow coats the pyrolyzed sticky bituminous coal particles and prevents them from agglomerating quickly. As the bituminous coal char particles swell, they are carried to the cooler upper regions of the reactor where they re-solidify. Other interesting phenomena were revealed regarding the transport (rheological) properties of the coal sawdust mixtures. The coal sawdust mixtures segregate quickly when transported. This is visibly apparent. To prevent bridges and ratholes from developing in the lowest coal feed hopper, it is normally fluidized. When feeding the coal sawdust mixtures the fluidizing gas was turned off to prevent segregation. The feed system worked as well with no fluidizing gas when using the mixtures as it did with fluidizing gas and only coal. In addition, it was inadvertently discovered that greatly increased pressure above the feeder resulted in greatly increased flow with the mixtures. Increased pressure above the feeder with coal only results in quickly plugging the feed system. Also, it was learned that addition of sawdust reduces the system loss during conveying compared to coal only. This is in spite of overall smaller particle sizes with the coal sawdust mixtures.« less

Recycling of water-susceptible pavements

NASA Astrophysics Data System (ADS)

Maupin, G. W.

1980-05-01

Several bituminous concrete interstate pavements that experienced failures suspected to have been caused by stripping were investigated. On two projects, the degree of deterioration, potential serviceability, and possible remedial measures were studied. Cores were taken to determine the degreee of stripping and tensile strength, and dynaflect tests were performed. An emulsion mix design was developed for stripped bituminous concrete removed from another project with the expectation that it could be used as a surface mix on a highway with a low traffic volume. While this expectation was not realized, it was concluded that the material is suitable for use in a base mix. A maintenance resurfacing on a fourth project that experienced stripping failure is being monitored and the performance is being evaluated.

Methane in the Upper Silesian Coal Basin (Poland) - problem of reserves and exploitation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wojcik, A.J.

1995-08-01

The Upper Silesian Coal Basin (USCB) is the best recognized and the most productive coal basin in Poland. The USCB is primarily defined by the extent of Carboniferous coal-bearing formations. The sedimentary fill displays the stratigraphic record of major progressive inversion phases of the entire Moravo-Silesian basin during the late and post-geosynclinal period of the Variscan orogeny. According to the last estimates the coal reserves occurring above the depth limit of 1500 in are as follows: documented reserves - 58 billion tons, prognostic reserves - 46 billion tons, total - 104 billion tons. The coal type is predominantly vitrinitic, andmore » ash content is reported to be in the range of 11-17% and average sulphur content is 1.13%. The rank of USCB coal is largely controlled by complex coalification processes. It ranges from high volatile bituminous B, through medium volatile bituminous to high rank special coal semi anthracite and anthracite. The methane content of coal seams in USCB varies in a very broad range of 0-22 m{sup 3}/t coal (dry, ash free basis). The average gas content increases considerably within the depth range 600-1000 in from 0.99 to 4.68 m{sup 3}/t coal (daf). In deeper horizons it is more or less stable varying within the range of 4.7-7.0 m{sup 3}/t coal (daf). By this estimate, on average, the methane content is about 12,5 m{sup 3}/ton. There are several estimates of coal-bed methane resources in the USCB based on different methods. The resources are as follows: documented deposits in active mines to 1000 m: 370 BCM, undeveloped deposits to 1000 in: 340 BCM, deposit between 1000 and 1500 m: 590 BCM, total: 1300 BCM. The coalbed gas from this basin is primarily composed of saturated hydrocarbons and Nitrogen which amount to 97 volume percent. The rest is dominant by Carbon dioxide and Hydrogen.« less

Coking properties of coal under pressure and their influence on moving-bed gasification. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lancet, M.S.; Curran, G.P.; Sim, F.A.

1982-08-01

The coking properties of seven bituminous coals, including three Eastern US coals, one Midwestern US coal, a Western US coal and two from the UK were studied with respect to the possible utilization of these coals in moving bed gasifier systems. Complete physical, chemical and petrographic analyses were obtained for each coal in addition to the highly specialized CCDC simulated gasifier coking test data. The effects of total pressure, hydrogen partial pressure, heating rate and the addition of gob and tar on the fluidity and swelling properties of each coal was studied. Samples of each coal were shock heated undermore » pressure to simulate coking in the top of a Lurgi gasifier. The resultant cokes were tested for various physical properties and the product yields were determined. Gas release patterns during pressurized pyrolysis were obtained in several instances. The data obtained in this work should provide a valuable data base for future gasifier feedstock evaluation programs.« less

Selected elements in major minerals from bituminous coal as determined by INAA: Implications for removing environmentally sensitive elements from coal

USGS Publications Warehouse

Palmer, C.A.; Lyons, P.C.

1996-01-01

The four most abundant minerals generally found in Euramerican bituminous coals are quartz, kaolinite, illite and pyrite. These four minerals were isolated by density separation and handpicking from bituminous coal samples collected in the Ruhr Basin, Germany and the Appalachian basin, U.S.A. Trace-element concentrations of relatively pure (??? 99+%) separates of major minerals from these coals were determined directly by using instrumental neutron activation analysis (INAA). As expected, quartz contributes little to the trace-element mass balance. Illite generally has higher trace-element concentrations than kaolinite, but, for the concentrates analyzed in this study, Hf, Ta, W, Th and U are in lower concentrations in illite than in kaolinite. Pyrite has higher concentrations of chalcophile elements (e.g., As and Se) and is considerably lower in lithophile elements as compared to kaolinite and illite. Our study provides a direct and sensitive method of determining trace-element relationships with minerals in coal. Mass-balance calculations suggest that the trace-element content of coal can be explained mainly by three major minerals: pyrite, kaolinite and illite. This conclusion indicates that the size and textural relationships of these major coal minerals may be a more important consideration as to whether coal cleaning can effectively remove the most environmentally sensitive trace elements in coal than what trace minerals are present.

Effect of fuels and domestic heating appliance types on emission factors of selected organic pollutants.

PubMed

Šyc, Michal; Horák, Jiří; Hopan, František; Krpec, Kamil; Tomšej, Tomáš; Ocelka, Tomáš; Pekárek, Vladimír

2011-11-01

This study reports on the first complex data set of emission factors (EFs) of selected pollutants from combustion of five fuel types (lignite, bituminous coal, spruce, beech, and maize) in six different domestic heating appliances of various combustion designs. The effect of fuel as well as the effect of boiler type was studied. In total, 46 combustion runs were performed, during which numerous EFs were measured, including the EFs of particulate matter (PM), carbon monoxide, polyaromatic hydrocarbons (PAH), hexachlorobenzene (HxCBz), polychlorinated dibenzo-p-dioxins and furans (PCDD/F), etc. The highest EFs of nonchlorinated pollutants were measured for old-type boilers with over-fire and under-fire designs and with manual stoking and natural draft. Emissions of the above-mentioned pollutants from modern-type boilers (automatic, downdraft) were 10 times lower or more. The decisive factor for emission rate of nonchlorinated pollutants was the type of appliance; the type of fuel plays only a minor role. Emissions of chlorinated pollutants were proportional mainly to the chlorine content in fuel, but the type of appliance also influenced the rate of emissions significantly. Surprisingly, higher EFs of PCDD/F from combustion of chlorinated bituminous coal were observed for modern-type boilers (downdraft, automatic) than for old-type ones. On the other hand, when bituminous coal was burned, higher emissions of HxCBz were found for old-type boilers than for modern-type ones.

Kansas coal distribution, resources, and potential for coalbed methane

USGS Publications Warehouse

Brady, L.L.

2000-01-01

100 ft (>30 m)] determined from 32 different coal beds. Strippable coal resources at a depth Kansas has large amounts of bituminous coal both at the surface and in the subsurface of eastern Kansas. Preliminary studies indicate at least 53 billion tons (48 billion MT) of deep coal [>100 ft (>30 m)] determined from 32 different coal beds. Strippable coal resources at a depth < 100 ft (<30 m) total 2.8 billion tons (2.6 billion MT), and this total is determined from 17 coals. Coal beds present in the Cherokee Group (Middle Pennsylvanian) represent most of these coal resource totals. Deep coal beds with the largest resource totals include the Bevier, Mineral, "Aw" (unnamed coal bed), Riverton, and Weir-Pittsburg coals, all within the Cherokee Group. Based on chemical analyses, coals in the southeastern part of the state are generally high volatile A bituminous, whereas coals in the east-central and northeastern part of the state are high-volatile B bituminous coals. The primary concern of coal beds in Kansas for deep mining or development of coalbed methane is the thin nature [<2 ft (0.6 m)] of most coal beds. Present production of coalbed methane is centered mainly in the southern Wilson/northern Montgomery County area of southeastern Kansas where methane is produced from the Mulky, Weir-Pittsburg, and Riverton coals.

Outdoor, indoor, and personal black carbon exposure from cookstoves burning solid fuels

PubMed Central

Downward, George S.; Hu, Wei; Rothman, Nat; Reiss, Boris; Wu, Guoping; Wei, Fusheng; Xu, Jun; Seow, Wei Jie; Brunekreef, Bert; Chapman, Robert S.; Qing, Lan; Vermeulen, Roel

2015-01-01

Background Black carbon (BC) emissions from solid fuel combustion are associated with increased morbidity and mortality and are important drivers of climate change. We studied BC measurements, approximated by particulate matter (PM2.5) absorbance, in rural Yunnan province, China whose residents use a variety of solid fuels for cooking and heating including: bituminous and anthracite coal, and wood. Methods Measurements were taken over 2 consecutive 24 h periods from 163 households in 30 villages. PM2.5 absorbance (PMabs) was measured using an EEL 043 Smoke Stain Reflectometer. Results PMabs measurements were higher in wood burning households (16.3 × 10−5 m−1) than bituminous and anthracite coal households (12 and 5.1 × 10−5 m−1 respectively). Among bituminous coal users, measurements varied by a factor of two depending on the coal source. Portable stoves (which are lit outdoors and brought indoors for use) were associated with reduced PMabs levels, but no other impact of stove design was observed. Outdoor measurements were positively correlated with and approximately half the level of indoor measurements (r= 0.49, p<0.01). Conclusion Measurements of BC (as approximated by PMabs) in this population are modulated by fuel type and source. This provides valuable insight into potential morbidity, mortality and climate change contributions of domestic usage of solid fuels. PMID:26452237

30 CFR 75.380 - Escapeways; bituminous and lignite mines.

Code of Federal Regulations, 2010 CFR

2010-07-01

...) Underground transformer stations, battery charging stations, substations, and rectifiers except— (A) Where... rectifiers and power centers with transformers that are either dry-type or contain nonflammable liquid...

Influence of the association of the EVA and NBR on the characteristics of modified bitumen

NASA Astrophysics Data System (ADS)

Bensaada, A.; Soudani, K.; Haddadi, S.; Saoula, S.

2015-03-01

Durability and the performance of pavement depend mainly on the characteristics of materials which change over time like all other organic substances. They are subject to significant changes due to environmental conditions during the different phases of use. In the present work we investigated experimentally the influence of the association of ethyl vinyl acetate polymer (EVA) with an industrial waste, acrylonitrile-butadiene rubber (NBR) on the modification of bitumen AC 35-50 and its rheological behavior. The incorporation of NBR and EVA in the bitumen improved its intrinsic characteristics (softening point, penetration and ductility). In addition to improving the characteristics of bituminous binders that will affect the durability of bituminous structures, the environment will be preserved by the recycling of industrial waste.

Multi-Attribute Selection of Coal Center Location: A Case Study in Thailand

NASA Astrophysics Data System (ADS)

Kuakunrittiwong, T.; Ratanakuakangwan, S.

2016-11-01

Under Power Development Plan 2015, Thailand has to diversify its heavily gas-fired electricity generation. The main owner of electricity transmission grids is responsible to implement several coal-fired power plants with clean coal technology. To environmentally handle and economically transport unprecedented quantities of sub-bituminous and bituminous coal, a coal center is required. The location of such facility is an important strategic decision and a paramount to the success of the energy plan. As site selection involves many criteria, Fuzzy Analytical Hierarchy Process or Fuzzy-AHP is applied to select the most suitable location among three candidates. Having analyzed relevant criteria and the potential alternatives, the result reveals that engineering and socioeconomic are important criteria and Map Ta Phut is the most suitable site for the coal center.

Secretinite-Reflectance and chemical data from two high volatile bituminous coals (Upper Carboniferous) of North America

USGS Publications Warehouse

Lyons, P.C.; Mastalerz, Maria

2001-01-01

Secretinite - a maceral of the inertinite group as recognized by the ICCP in 1996- is a noncellular maceral of seed fern origin. New reflectance data indicate that this maceral has primary anisotropy with bireflectances of 0.4% to 0.9% in high-volatile B bituminous (Ro = 0.6%) Carboniferous coal of North America. The highest reflectance is in cross-section as opposed to longitudinal section. Characteristic feature of secretinite is the virtual absence of Si and Al, unlike that in associated vitrinite. This indicates the absence of submicron aluminosilicates in secretinite and their presence in vitrinites. Secretinite is highly aromatic as indicated by low O/C ratios and high contribution of aromatic hydrogen bands detected by FTIR analysis. ?? 2001 Elsevier Science B.V. All rights reserved.

Study on coal char ignition by radiant heat flux.

NASA Astrophysics Data System (ADS)

Korotkikh, A. G.; Slyusarskiy, K. V.

2017-11-01

The study on coal char ignition by CO2-continuous laser was carried out. The coal char samples of T-grade bituminous coal and 2B-grade lignite were studied via CO2-laser ignition setup. Ignition delay times were determined at ambient condition in heat flux density range 90-200 W/cm2. The average ignition delay time value for lignite samples were 2 times lower while this difference is larger in high heat flux region and lower in low heat flux region. The kinetic constants for overall oxidation reaction were determined using analytic solution of simplified one-dimensional heat transfer equation with radiant heat transfer boundary condition. The activation energy for lignite char was found to be less than it is for bituminous coal char by approximately 20 %.

Development of Pavement Temperature Contours for India

NASA Astrophysics Data System (ADS)

Nivitha, M. R.; Krishnan, J. M.

2014-06-01

The stress-strain response of the bituminous pavements is highly sensitive to temperature. To systematically analyze the pavement performance, it is necessary that one understands the variation of pavement temperature spatially and temporally during the life time of a pavement. In this investigation, historic air temperature data for 37 locations across India was collected. Using this database, pavement temperature data was predicted by an appropriate air temperature-pavement temperature model. High and low temperature pavement temperature contours were generated for the first time for India. It was seen that the locations spanning from Srinagar to Madhya Pradesh and Rajasthan to Orissa were extremely critical. The minimum temperature in these locations was 10 C and the maximum temperature was around 68 C. Clearly such information is necessary when making choice of binder grade and bituminous layer thickness.

Field Testing of a Wet FGD Additive for Enhanced Mercury Control - Task 5 Full-Scale Test Results

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gary Blythe; MariJon Owens

2007-12-01

This Topical Report summarizes progress on Cooperative Agreement DE-FC26-04NT42309, 'Field Testing of a Wet FGD Additive'. The objective of the project is to demonstrate the use of two flue gas desulfurization (FGD) additives, Evonik Degussa Corporation's TMT-15 and Nalco Company's Nalco 8034, to prevent the re-emission of elemental mercury (Hg{sup 0}) in flue gas exiting wet FGD systems on coal-fired boilers. Furthermore, the project intends to demonstrate whether the additive can be used to precipitate most of the mercury (Hg) removed in the wet FGD system as a fine salt that can be separated from the FGD liquor and bulkmore » solid byproducts for separate disposal. The project is conducting pilot- and full-scale tests of the additives in wet FGD absorbers. The tests are intended to determine required additive dosages to prevent Hg{sup 0} re-emissions and to separate mercury from the normal FGD byproducts for three coal types: Texas lignite/Powder River Basin (PRB) coal blend, high-sulfur Eastern bituminous coal, and low-sulfur Eastern bituminous coal. The project team consists of URS Group, Inc., EPRI, Luminant Power (was TXU Generation Company LP), Southern Company, IPL (an AES company), Evonik Degussa Corporation and the Nalco Company. Luminant Power has provided the Texas lignite/PRB co-fired test site for pilot FGD tests and cost sharing. Southern Company has provided the low-sulfur Eastern bituminous coal host site for wet scrubbing tests, as well as the pilot- and full-scale jet bubbling reactor (JBR) FGD systems tested. IPL provided the high-sulfur Eastern bituminous coal full-scale FGD test site and cost sharing. Evonik Degussa Corporation is providing the TMT-15 additive, and the Nalco Company is providing the Nalco 8034 additive. Both companies are also supplying technical support to the test program as in-kind cost sharing. The project is being conducted in six tasks. Of the six project tasks, Task 1 involves project planning and Task 6 involves management and reporting. The other four tasks involve field testing on FGD systems, either at pilot or full scale. The four tasks include: Task 2 - Pilot Additive Testing in Texas Lignite Flue Gas; Task 3 - Full-scale FGD Additive Testing in High-sulfur Eastern Bituminous Flue Gas; Task 4 - Pilot Wet Scrubber Additive Tests at Plant Yates; and Task 5 - Full-scale Additive Tests at Plant Yates. The pilot-scale tests and the full-scale test using high-sulfur coal were completed in 2005 and 2006 and have been previously reported. This topical report presents the results from the Task 5 full-scale additive tests, conducted at Southern Company's Plant Yates Unit 1. Both additives were tested there.« less

Field Testing of a Wet FGD Additive for Enhanced Mercury Control - Task 3 Full-scale Test Results

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gary Blythe

2007-05-01

This Topical Report summarizes progress on Cooperative Agreement DE-FC26-04NT42309, 'Field Testing of a Wet FGD Additive'. The objective of the project is to demonstrate the use of a flue gas desulfurization (FGD) additive, Degussa Corporation's TMT-15, to prevent the reemission of elemental mercury (Hg{sup 0}) in flue gas exiting wet FGD systems on coal-fired boilers. Furthermore, the project intends to demonstrate whether the additive can be used to precipitate most of the mercury (Hg) removed in the wet FGD system as a fine TMT salt that can be separated from the FGD liquor and bulk solid byproducts for separate disposal.more » The project is conducting pilot- and full-scale tests of the TMT-15 additive in wet FGD absorbers. The tests are intended to determine required additive dosages to prevent Hg{sup 0} reemissions and to separate mercury from the normal FGD byproducts for three coal types: Texas lignite/Power River Basin (PRB) coal blend, high-sulfur Eastern bituminous coal, and low-sulfur Eastern bituminous coal. The project team consists of URS Group, Inc., EPRI, TXU Generation Company LP, Southern Company, and Degussa Corporation. TXU Generation has provided the Texas lignite/PRB cofired test site for pilot FGD tests, Monticello Steam Electric Station Unit 3. Southern Company is providing the low-sulfur Eastern bituminous coal host site for wet scrubbing tests, as well as the pilot- and full-scale jet bubbling reactor (JBR) FGD systems to be tested. IPL, an AES company, provided the high-sulfur Eastern bituminous coal full-scale FGD test site and cost sharing. Degussa Corporation is providing the TMT-15 additive and technical support to the test program as cost sharing. The project is being conducted in six tasks. Of the six project tasks, Task 1 involves project planning and Task 6 involves management and reporting. The other four tasks involve field testing on FGD systems, either at pilot or full scale. The four tasks include: Task 2 - Pilot Additive Testing in Texas Lignite Flue Gas; Task 3 - Full-scale FGD Additive Testing in High-sulfur Eastern Bituminous Flue Gas; Task 4 - Pilot Wet Scrubber Additive Tests at Plant Yates; and Task 5 - Full-scale Additive Tests at Plant Yates. The pilot-scale tests were completed in 2005 and have been previously reported. This topical report presents the results from the Task 3 full-scale additive tests, conducted at IPL's Petersburg Station Unit 2. The Task 5 full-scale additive tests will be conducted later in calendar year 2007.« less

Recycling of water-susceptible pavements.

DOT National Transportation Integrated Search

1980-01-01

Several bituminous concrete interstate pavements that experienced failures suspected to have been caused by stripping were investigated. On two projects, the degree of deterioration, potential serviceability, and possible remedial measures were studi...

[In vitro toxicity of naturally occurring silica nanoparticles in C1 coal in bronchial epithelial cells].

PubMed

Li, Guangjian; Huang, Yunchao; Liu, Yongjun; Guo, Lv; Zhou, Yongchun; Yang, Kun; Chen, Ying; Zhao, Guangqiang; Lei, Yujie

2012-10-01

China's Xuan Wei County in Yunnan Province have the world's highest incidence of lung cancer in nonsmoking women-20 times higher than the rest of China. Previous studies showed, this high lung cancer incidence may be associated with the silica particles embedded in the production combustion from the C1 coal. The aim of this study is to separate the silica particles from production combustion from the C1 bituminous coal in Xuan Wei County of Yunnan Province, and study in vitro toxicity of naturally occurring silica particles on BEAS-2B. ①Separating the silica particles from combustion products of C1 bituminous coal by physical method, observing the morphology by Scanning Electron Microscope, analysis elements by SEM-EDX, observed the single particle morphology by Transmission Electron Microscope, analyed its particle size distribution by Laser particle size analyzer, the surface area of silica particles were determined by BET nitrogen adsorption analysis; ②Cell viability of the experimental group (silica; naturally occurring), control group (silica; industrial produced and crystalline silica) was detected by assay used the 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide (MTT) method, and the reactive oxygen species (ROS), lactate dehydrogenase (LDH) were determined after 24 h-72 h exposed to these particles. ①The physical method can separate silica particles from production combustion from the C1 bituminous coal, which have different size, and from 30 nm to 120 nm particles accounted for 86.8%, different morphology, irregular surface area and containing trace of aluminum, calcium and iron and other elements; ②Under the same concentration, the experiment group have higher toxicity on BEAS-2B than control groups. Physical method can separate silica particles from production combustion from the C1 bituminous coal and not change the original morphology and containing trace; ②Naturally occurring silica nanoparticles have irregular morphology, surface area, and containing complex trace elements may has greater toxicity than the silica nanoparticle of industrial produced and crystalline silica.

Saw & seal, airport pavement.

DOT National Transportation Integrated Search

2009-05-01

Due to extreme cold temperatures, hot bituminous pavements on Maines airports are subject to transverse : or thermal cracking. This can lead to poorly performing pavement structure causing heaving and : settlement problems. Studies have shown that...

Chip seal performance measures : best practices.

DOT National Transportation Integrated Search

2015-03-01

The Washington State Department of Transportation (WSDOT) has a long history of designing, constructing, : and maintaining chip seal or bituminous surface treatment pavements. However, to date WSDOT has not : developed pavement performance indicators...

Performance related specifications for bituminous concrete.

DOT National Transportation Integrated Search

1984-01-01

This report discusses the philosophy and evolution of performance related specifications. The properties of most .importance in the construction of asphaltic concrete pavements, as well as the associated specifications, are listed and discussed. The ...

40 CFR 61.143 - Standard for roadways.

Code of Federal Regulations, 2012 CFR

2012-07-01

... area of asbestos ore deposits (asbestos mine): or (b) It is a temporary roadway at an active asbestos mill site and is encapsulated with a resinous or bituminous binder. The encapsulated road surface must...

40 CFR 61.143 - Standard for roadways.

Code of Federal Regulations, 2011 CFR

2011-07-01

... area of asbestos ore deposits (asbestos mine): or (b) It is a temporary roadway at an active asbestos mill site and is encapsulated with a resinous or bituminous binder. The encapsulated road surface must...

40 CFR 61.143 - Standard for roadways.

Code of Federal Regulations, 2014 CFR

2014-07-01

... area of asbestos ore deposits (asbestos mine): or (b) It is a temporary roadway at an active asbestos mill site and is encapsulated with a resinous or bituminous binder. The encapsulated road surface must...

40 CFR 61.143 - Standard for roadways.

Code of Federal Regulations, 2013 CFR

2013-07-01

... area of asbestos ore deposits (asbestos mine): or (b) It is a temporary roadway at an active asbestos mill site and is encapsulated with a resinous or bituminous binder. The encapsulated road surface must...

14 CFR 151.39 - Project eligibility.

Code of Federal Regulations, 2010 CFR

2010-01-01

... located; and (ii) Adequate replacement housing that is open to all persons, regardless of race, color...) Bituminous resurfacing of pavements with a minimum of 100 pounds of plant-mixed material for each square yard...

14 CFR 151.39 - Project eligibility.

Code of Federal Regulations, 2011 CFR

2011-01-01

... located; and (ii) Adequate replacement housing that is open to all persons, regardless of race, color...) Bituminous resurfacing of pavements with a minimum of 100 pounds of plant-mixed material for each square yard...

Results of reflective crack questionnaire survey.

DOT National Transportation Integrated Search

1973-01-01

Department engineers were surveyed to obtain their opinions on the potential detrimental effects of transverse reflective cracks through the surface course of bituminous pavements and the costs of preventive measures. The majority of respondents (67%...

Vibratory roller study.

DOT National Transportation Integrated Search

1984-01-01

Recently, much criticism has been directed toward the use of vibratory rollers to compact bituminous concrete. The results of the study reported here indicate that when these rollers are operated properly they can produce dense, strong, smooth riding...

Combustion characteristics and arsenic retention during co-combustion of agricultural biomass and bituminous coal.

PubMed

Zhou, Chuncai; Liu, Guijian; Wang, Xudong; Qi, Cuicui; Hu, Yunhu

2016-08-01

A combination of thermogravimetric analysis (TG) and laboratory-scale circulated fluidized bed combustion experiment was conducted to investigate the thermochemical, kinetic and arsenic retention behavior during co-combustion bituminous coal with typical agricultural biomass. Results shown that ignition performance and thermal reactivity of coal could be enhanced by adding biomass in suitable proportion. Arsenic was enriched in fly ash and associated with fine particles during combustion of coal/biomass blends. The emission of arsenic decreased with increasing proportion of biomass in blends. The retention of arsenic may be attributed to the interaction between arsenic and fly ash components. The positive correlation between calcium content and arsenic concentration in ash suggesting that the arsenic-calcium interaction may be regarded as the primary mechanism for arsenic retention. Copyright © 2016 Elsevier Ltd. All rights reserved.

SUBMICROSCOPIC ( less than 1 mu m) MINERAL CONTENTS OF VITRINITES IN SELECTED BITUMINOUS COAL BEDS.

USGS Publications Warehouse

Minkin, J.A.; Chao, E.C.T.; Thompson, C.L.; Wandless, M.-V.; Dulong, F.T.; Larson, R.R.; Neuzil, S.G.; ,

1983-01-01

An important aspect of the petrographic description of coal is the characterization of coal quality, including chemical attributes. For geologic investigations, data on the concentrations, distribution, and modes of occurrence of minor and trace elements provide a basis for reconstructing the probable geochemical environment of the swamp material that was converted into peat, and the geochemical conditions that prevailed during and subsequent to coalification. We have been using electron (EPMA) and proton (PIXE) microprobe analytical methods to obtain data on the chemical characteristics of specific coal constituents in their original associations within coal samples. The present study is aimed at evaluation of the nature of mineral occurrences and heterogeneous elemental concentrations within vitrinites. Vitrinites are usually the most abundant, and therefore most important, maceral group in bituminous coal. 8 refs.

Analysis of coals and biomass pyrolysis using the distributed activation energy model.

PubMed

Li, Zhengqi; Liu, Chunlong; Chen, Zhichao; Qian, Juan; Zhao, Wei; Zhu, Qunyi

2009-01-01

The thermal decomposition of coals and biomass was studied using thermogravimetric analysis with the distributed activation energy model. The integral method resulted in Datong bituminous coal conversions of 3-73% at activation energies of 100-486 kJ/mol. The corresponding frequency factors were e(19.5)-e(59.0)s(-1). Jindongnan lean coal conversions were 8-52% at activation energies of 100-462 kJ/mol. Their corresponding frequency factors were e(13.0)-e(55.8)s(-1). The conversion of corn-stalk skins were 1-84% at activation energies of 62-169 kJ/mol with frequency factors of e(10.8)-e(26.5)s(-1). Datong bituminous coal, Jindongnan lean coal and corn-stalk skins had approximate Gaussian distribution functions with linear ln k(0) to E relationships.

Pelletizing/reslurrying as a means of distributing and firing clean coal

DOE Office of Scientific and Technical Information (OSTI.GOV)

Conkle, H.N.; Raghavan, J.K.; Smit, F.J.

1991-11-21

The objective of this study is to develop technology that permits the practical and economic preparation, storage, handling, and transportation of coal pellets, which can be reslurried into Coal water fuels (CWF) suitable for firing in small- and medium-size commercial and industrial boilers, furnaces, and engines. The project includes preparing coal pellets and capsules from wet filter cake that can be economically stored, handled, transported, and reslurried into a CWF that can be suitably atomized and fired at the user site. The wet cakes studied were prepared from ultra-fine (95% -325 mesh) coal beneficiated by advanced froth-flotation techniques. The coalsmore » studied included two eastern bituminous coals, one from Virginia (Elkhorn) and one from Illinois (Illinois No. 6) and one western bituminous coal from Utah (Sky Line coal).« less

Report: Potential environmental impact of exempt site materials - a case study of bituminous road planings and waste soils.

PubMed

Bark, Marjorie; Bland, Michael; Grimes, Sue

2009-09-01

The use of waste materials for ecological benefit, agricultural improvement or as part of construction works are often exempt from waste management control in order to maximize the reuse of material that would otherwise be disposed of to landfill. It is important, however, to determine whether there is potential for such waste to cause environmental harm in the context of the basis for granting exemptions under the relevant framework objective to ensure that waste is recovered or disposed of without risk to water, air, soil, plants or animals. The potential for environmental harm was investigated by leaching studies on two wastes commonly found at exempt sites: bituminous road planings and waste soils. For bituminous road planings, the organic components of the waste were identified by their solubility in organic solvents but these components would have low environmental impact in terms of bioavailability. Leaching studies of the heavy metals copper, lead and zinc, into the environment, under specific conditions and particularly those modelling acid rain and landfill leachate conditions showed that, except for copper, the amounts leached fell within Waste Acceptance Criteria compliance limits for defining waste as inert waste. The fact that the amount of copper leached was greater than the Waste Acceptance Criteria level suggests that either additional testing of wastes regarded as exempt should be carried out to ensure that they are in analytical compliance or that legislation should allow for the potential benefits of reuse to supersede deviations from analytical compliance.

Coalbed methane, Cook Inlet, south-central Alaska: A potential giant gas resource

USGS Publications Warehouse

Montgomery, S.L.; Barker, C.E.

2003-01-01

Cook Inlet Basin of south-central Alaska is a forearc basin containing voluminous Tertiary coal deposits with sufficient methane content to suggest a major coalbed gas resource. Coals ranging in thickness from 2 to 50 ft (0.6 to 15 m) and in gas content from 50 to 250 scf/ton (1.6 to 7.8 cm2/g) occur in Miocene-Oligocene fluvial deposits of the Kenai Group. These coals have been identified as the probable source of more than 8 tcf gas that has been produced from conventional sandstone reservoirs in the basin. Cook Inlet coals can be divided into two main groups: (1) those of bituminous rank in the Tyonek Formation that contain mainly thermogenic methane and are confined to the northeastern part of the basin (Matanuska Valley) and to deep levels elsewhere; and (2) subbituminous coals at shallow depths (<5000 ft [1524 m]) in the Tyonek and overlying Beluga formations, which contain mainly biogenic methane and cover most of the central and southern basin. Based on core and corrected cuttings-desorption analyses, gas contents average 230 scf/ton (7.2 cm2/g) for bituminous coals and 80 scf/ton (2.5 cm2/g) for subbituminous coals. Isotherms constructed for samples of both coal ranks suggest that bituminous coals are saturated with respect to methane, whereas subbituminous coals at shallow depths along the eroded west-central basin margin are locally unsaturated. A preliminary estimate of 140 tcf gas in place is derived for the basin.

Reuse of bituminous pavements: A mini-review of research, regulations and modelling.

PubMed

Anthonissen, Joke; Van den Bergh, Wim; Braet, Johan

2017-04-01

Bituminous pavement can be recycled - even multiple times - by reusing it in new bituminous mixtures. If the mechanical properties of the binder get worse, this reclaimed asphalt is often used in the sub-structure of the road. Apparently, up till now, no end-of-life phase exists for the material. Actually, defining the end-of-life and the end-of-waste stage of a material is important for life cycle assessment modelling. Various standards and scientific studies on modelling life cycle assessment are known, but the crucial stages are not yet defined for reclaimed asphalt pavement. Unlike for iron, steel and aluminium scrap, at this moment, no legislative end-of-waste criteria for aggregates are formulated by the European Commission. More research is necessary in order to develop valuable end-of-life criteria for aggregates. This contribution is a mini-review article of the current regulations, standards and studies concerning end-of-life and end-of-waste of reclaimed asphalt pavement. The existing methodology in order to define end-of-waste criteria, a case study on aggregates and the argumentation used in finished legislative criteria are the basis to clarify some modelling issues for reclaimed asphalt material. Hence, this contribution elucidates the assignment of process environmental impacts to a life cycle stage as defined by EN15804, that is, end-of-life stage (C) and the supplementary information Module D with benefits and loads beyond the system boundary.

Strain accumulation in bituminous binders under repeated creep-recovery loading predicted from small-amplitude oscillatory shear (SAOS) experiments

NASA Astrophysics Data System (ADS)

Laukkanen, Olli-Ville; Winter, H. Henning

2017-11-01

The creep-recovery (CR) test starts out with a period of shearing at constant stress (creep) and is followed by a period of zero-shear stress where some of the accumulated shear strain gets reversed. Linear viscoelasticity (LVE) allows one to predict the strain response to repeated creep-recovery (RCR) loading from measured small-amplitude oscillatory shear (SAOS) data. Only the relaxation and retardation time spectra of a material need to be known and these can be determined from SAOS data. In an application of the Boltzmann superposition principle (BSP), the strain response to RCR loading can be obtained as a linear superposition of the strain response to many single creep-recovery tests. SAOS and RCR data were collected for several unmodified and modified bituminous binders, and the measured and predicted RCR responses were compared. Generally good agreement was found between the measured and predicted strain accumulation under RCR loading. However, in the case of modified binders, the strain accumulation was slightly overestimated (≤20% relative error) due to the insufficient SAOS information at long relaxation times. Our analysis also demonstrates that the evolution in the strain response under RCR loading, caused by incomplete recovery, can be reasonably well predicted by the presented methodology. It was also shown that the outlined modeling framework can be used, as a first approximation, to estimate the rutting resistance of bituminous binders by predicting the values of the Multiple Stress Creep Recovery (MSCR) test parameters.

Evaluation of Troxler model 3411 nuclear gage.

DOT National Transportation Integrated Search

1978-01-01

The performance of the Troxler Electronics Laboratory Model 3411 nuclear gage was evaluated through laboratory tests on the Department's density and moisture standards and field tests on various soils, base courses, and bituminous concrete overlays t...

Best practices and performance assessment for preventive maintenance treatments for Virginia pavements.

DOT National Transportation Integrated Search

2015-08-01

Preventive maintenance has the potential to improve network condition by retarding future pavement deterioration. This : report outlines guidelines for implementing a preventive maintenance policy for bituminous pavements. : Preventive maintenance tr...

Seal coat research project

DOT National Transportation Integrated Search

1999-12-01

This study evaluates the use of seal coating as a method to protect bituminous pavements from oxidation, water infiltration, and raveling. The Minnesota Department of Transportation (Mn/DOT) applied seal coating to a roadway segment of Trunk Highway ...

30 CFR 90.2 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... old section 203(b) program (36 FR 20601, October 27, 1971), or under § 90.3 (Part 90 option; notice of... area bituminous coal, lignite, or anthracite from its natural deposits in the earth by any means or...

30 CFR 90.2 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... old section 203(b) program (36 FR 20601, October 27, 1971), or under § 90.3 (Part 90 option; notice of... area bituminous coal, lignite, or anthracite from its natural deposits in the earth by any means or...

30 CFR 90.2 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... old section 203(b) program (36 FR 20601, October 27, 1971), or under § 90.3 (Part 90 option; notice of... area bituminous coal, lignite, or anthracite from its natural deposits in the earth by any means or...

30 CFR 90.2 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... old section 203(b) program (36 FR 20601, October 27, 1971), or under § 90.3 (Part 90 option; notice of... area bituminous coal, lignite, or anthracite from its natural deposits in the earth by any means or...

30 CFR 90.2 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... old section 203(b) program (36 FR 20601, October 27, 1971), or under § 90.3 (Part 90 option; notice of... area bituminous coal, lignite, or anthracite from its natural deposits in the earth by any means or...

Bituminous concrete overlay studies.

DOT National Transportation Integrated Search

1971-01-01

Deflection tests conducted on eight sections of primary highway, both before and after asphaltic concrete resurfacings, were analyzed as a study of the utility of such tests in the design of overlays. The application of tentative traffic and allowabl...

Aggregate gradation control program, Virginia.

DOT National Transportation Integrated Search

1985-01-01

In 1983, Virginia implemented a specification for the acceptance of aggregate base and bituminous concrete in which the producer undertook the acceptance testing and state personnel did much reduced testing as a monitoring program. Although some peop...

Quality control analysis : part I : asphaltic concrete.

DOT National Transportation Integrated Search

1964-11-01

This report deals with the statistical evaluation of results from several hot mix plants to determine the pattern of variability with respect to bituminous hot mix characteristics. : Individual tests results when subjected to frequency distribution i...

Cold in-place recycled bituminous pavement Dorset-Danby, VT.

DOT National Transportation Integrated Search

2015-01-01

The report documents the long-term performance and cost effectiveness of four rehabilitation : treatments in a mostly homogenous environment. The underlying subbase and subgrade soils, traffic : volume, existing pavement structure and ambient conditi...

Alternatives to Full-Depth Patching on Resurfacing Projects

DOT National Transportation Integrated Search

1993-09-01

The vast majority of Illinois' non-interstate network is constructed of jointed Portland cement concrete (PCC). Typically, Illinois' first significant rehabilitation efforts for jointed PCC pavements are in the form of full-depth bituminous concrete ...

Ignition and Combustion of Pulverized Coal and Biomass under Different Oxy-fuel O2/N2 and O2/CO2 Environments

NASA Astrophysics Data System (ADS)

Khatami Firoozabadi, Seyed Reza

This work studied the ignition and combustion of burning pulverized coals and biomasses particles under either conventional combustion in air or oxy-fuel combustion conditions. Oxy-fuel combustion is a 'clean-coal' process that takes place in O2/CO2 environments, which are achieved by removing nitrogen from the intake gases and recirculating large amounts of flue gases to the boiler. Removal of nitrogen from the combustion gases generates a high CO2-content, sequestration-ready gas at the boiler effluent. Flue gas recirculation moderates the high temperatures caused by the elevated oxygen partial pressure in the boiler. In this study, combustion of the fuels took place in a laboratory laminar-flow drop-tube furnace (DTF), electrically-heated to 1400 K, in environments containing various mole fractions of oxygen in either nitrogen or carbon-dioxide background gases. The experiments were conducted at two different gas conditions inside the furnace: (a) quiescent gas condition (i.e., no flow or inactive flow) and, (b) an active gas flow condition in both the injector and furnace. Eight coals from different ranks (anthracite, semi-snthracite, three bituminous, subbituminous and two lignites) and four biomasses from different sources were utilized in this work to study the ignition and combustion characteristics of solid fuels in O2/N2 or O2/CO2 environments. The main objective is to study the effect of replacing background N2 with CO2, increasing O2 mole fraction and fuel type and rank on a number of qualitative and quantitative parameters such as ignition/combustion mode, ignition temperature, ignition delay time, combustion temperatures, burnout times and envelope flame soot volume fractions. Regarding ignition, in the quiescent gas condition, bituminous and sub-bituminous coal particles experienced homogeneous ignition in both O2/N 2 and O2/CO2 atmospheres, while in the active gas flow condition, heterogeneous ignition was evident in O2/CO 2. Anthracite, semi-anthracite and lignites mostly experienced heterogeneous ignition in either O2/N2 or O2/CO2 atmospheres in both flow conditions. Replacing the N2 by CO 2 slightly increased the ignition temperature (30--40K). Ignition temperatures increased with the enhancement of coal rank in either air or oxy-fuel combustion conditions. However, increasing oxygen mole fraction decreased the ignition temperature for all coals. The ignition delay of coal particles was prolonged in the slow-heating O2/CO2 atmospheres, relative to the faster-heating O2/N2 atmospheres, particularly at high-diluent mole fractions. At higher O2 mole fractions, ignition delays decreased in both environments. Higher rank fuels such as anthracite and semi-anthracite experienced higher ignition delays while lower rank fuels such as lignite and biomasses experienced lower igniton delay times. In combustion, fuel particles were observed to burn in different modes, such as two-mode, or in one-mode combustion, depending on their rank and the furnace conditions. Strong tendencies were observed for all fuels to burn in one-mode when N2 was replaced by CO2, and when O 2 mole fraction increased in both environments. Moreover, increasing the coal rank, from lignite to bituminous, enhanced the tendency of coal particles to exhibit a two-mode combustion behavior. Particle luminosity, fragmentation and deduced temperatures were higher in O2/N2 than in O2/CO2 atmospheres, and corresponding burnout times were shorter, at the same O2 mole fractions. Particle luminosity and temperatures increased with increasing O2 mole fractions in both N2 and in CO2 background gases, and corresponding burnout times decreased with increasing O2 mole fractions. Bituminous coal particles swelled, whereas sub-bituminous coal particles exhibited limited fragmentation prior to and during the early stages of combustion. Lignite coal particles fragmented extensively and burned in one-mode regardless of the O2 mole fraction and the background gas. The timing of fragmentation (prior or after ignition) and the number of fragments depended on the type of the lignite and on the particle shape. Temperatures and burnout times of particles were also affected by the combustion mode. In nearly all bituminous and biomass particles combustion, sooty envelope flames were formed around the particles. Replacement of background N 2 by CO2 gas decreased the average soot volume fraction, fv, whereas increasing O2 from 20% to 30--40% increased the fv and then further increasing O2 to 100% decreased the soot volume fraction drastically. bituminous coal particle flames generated lower soot volume fractions in the range 2x10 -5--9x10-5, depending on O2 mole fraction. Moreover, biomass particle flames were optically thin and of equal-sized at all O2 mole fractions. (Abstract shortened by UMI.).

Field Testing of a Wet FGD Additive for Enhanced Mercury Control

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gary Blythe; MariJon Owens

2007-12-31

This document is the final report for DOE-NETL Cooperative Agreement DE-FC26-04NT42309, 'Field Testing of a Wet FGD Additive'. The objective of the project has been to demonstrate the use of two flue gas desulfurization (FGD) additives, Evonik Degussa Corporation's TMT-15 and Nalco Company's Nalco 8034, to prevent the re-emission of elemental mercury (Hg{sup 0}) in flue gas exiting wet FGD systems on coal-fired boilers. Furthermore, the project was intended to demonstrate whether such additives can be used to precipitate most of the mercury (Hg) removed in the wet FGD system as a fine salt that can be separated from themore » FGD liquor and bulk solid byproducts for separate disposal. The project involved pilot- and full-scale tests of the additives in wet FGD absorbers. The tests were intended to determine required additive dosages to prevent Hg{sup 0} re-emissions and to separate mercury from the normal FGD byproducts for three coal types: Texas lignite/Powder River Basin (PRB) coal blend, high-sulfur Eastern bituminous coal, and low-sulfur Eastern bituminous coal. The project team consists of URS Group, Inc., EPRI, Luminant Power (was TXU Generation Company LP), Southern Company, IPL (an AES company), Evonik Degussa Corporation and the Nalco Company. Luminant Power provided the Texas lignite/PRB co-fired test site for pilot FGD tests and project cost sharing. Southern Company provided the low-sulfur Eastern bituminous coal host site for wet scrubbing tests, the pilot- and full-scale jet bubbling reactor (JBR) FGD systems tested, and project cost sharing. IPL provided the high-sulfur Eastern bituminous coal full-scale FGD test site and cost sharing. Evonik Degussa Corporation provided the TMT-15 additive, and the Nalco Company provided the Nalco 8034 additive. Both companies also supplied technical support to the test program as in-kind cost sharing. The project was conducted in six tasks. Of the six tasks, Task 1 involved project planning and Task 6 involved management and reporting. The other four tasks involved field testing on FGD systems, either at pilot or full scale. These four tasks included: Task 2 - Pilot Additive Testing in Texas Lignite Flue Gas; Task 3 - Full-scale FGD Additive Testing in High-sulfur Eastern Bituminous Flue Gas; Task 4 - Pilot Wet Scrubber Additive Tests at Plant Yates; and Task 5 - Full-scale Additive Tests at Plant Yates. The pilot-scale tests were completed in 2005 and the full-scale test using high-sulfur coal was completed in 2006; only the TMT-15 additive was tested in these efforts. The Task 5 full-scale additive tests conducted at Southern Company's Plant Yates Unit 1 were completed in 2007, and both the TMT-15 and Nalco 8034 additives were tested.« less

Field investigation of verglimit.

DOT National Transportation Integrated Search

1986-01-01

Verglimit is a calcium chloride based material that is incorporated into bituminous surface mixes to prevent ice and snow from sticking to the pavement. Two test sections were installed and the effectiveness of the Verglimit was evaluated for two win...

Evaluation of vacuum pycnometer : final report.

DOT National Transportation Integrated Search

1977-06-01

This report is concerned with the evaluation of the Yale vacuum pycnometer to determine the feasibility of its use for the rapid determination of maximum specific gravity and asphalt content of bituminous paving mixtures. Asphalt contents of plant-mi...

Evaluation of Reclaimed Rubber in Bituminous Pavements

DOT National Transportation Integrated Search

1995-06-01

Section 1038 of the 1991 Intermodal Surface Transportation Efficiency Act (ISTEA) mandated use of crumb rubber from scrap tires in asphalt pavement starting in FY 94. To gain some experience, the Illinois Department of Transportation (IDOT) construct...

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yao, S.C.; Manwani, P.

Coal-water slurries have been regarded as a potential substitute for heavy fuel oil. Various demonstrations of coal-water slurry combustion have been performed; however, a fundamental understanding of how the combustion process of a slurry fuel is enhanced is still not adequate. The combustion of coal-water mixture droplets suspended on microthermocouples has been investigated. It was found that droplets of lignite coal (which is a noncaking coal) burn effectively; however, droplets of bituminous coal (which is a caking coal) are relatively difficult to burn. During the heat-up of bituminous coal-water slurry droplets may turn to ''popcorn'' and show significant agglomeration. Themore » incomplete combustion of coal-water slurry droplets in furnaces has been reported, and this is a drawback of this process. The objective of the present study is to explore the possibility of enhancing the combustion of coal-water slurry droplets with the use of a combustible emulsified oil.« less

Application of infrared camera to bituminous concrete pavements: measuring vehicle

NASA Astrophysics Data System (ADS)

Janků, Michal; Stryk, Josef

2017-09-01

Infrared thermography (IR) has been used for decades in certain fields. However, the technological level of advancement of measuring devices has not been sufficient for some applications. Over the recent years, good quality thermal cameras with high resolution and very high thermal sensitivity have started to appear on the market. The development in the field of measuring technologies allowed the use of infrared thermography in new fields and for larger number of users. This article describes the research in progress in Transport Research Centre with a focus on the use of infrared thermography for diagnostics of bituminous road pavements. A measuring vehicle, equipped with a thermal camera, digital camera and GPS sensor, was designed for the diagnostics of pavements. New, highly sensitive, thermal cameras allow to measure very small temperature differences from the moving vehicle. This study shows the potential of a high-speed inspection without lane closures while using IR thermography.

The joint Australia/Federal Republic of Germany feasibility study on the conversion of Australian coals into liquid fuels in Australia

NASA Astrophysics Data System (ADS)

Imhausen, K. H.

1982-08-01

The IG hydrogenation process used commercially in Germany up to 1945, was improved. Pilot plants in Germany are presently under construction or in the start-up phase. A technical concept for the conversion of Australian bituminous coals and/or Australian brown coals into automotive fuels, using coal hydrogenation, gasification and Fisher-Tropsch synthesis was developed. Development of technology, consumption figures and of expenditure/investment for a complete plant, producing about 3 million tons of automotive fuels per year, was also attempted. The results show that standard automotive fuels are produced from bituminous coal, using a combination of high pressure coal hydrogenation and of Fisher-Tropsch synthesis, and from brown coal, using high pressure coal hydrogenation only. Under the assumption that crude oil prices increase 3% more rapidly than yearly inflation, and the raw material cost are staying at a low level, commercial plants are planned.

Upper Cretaceous bituminous coal deposits of the Olmos Formation, Maverick County, Texas

USGS Publications Warehouse

Hook, Robert W.; Warwick, Peter D.; SanFilipo, John R.; Warwick, Peter D.; Karlsen, Alexander K.; Merrill, Matthew D.; Valentine, Brett J.

2011-01-01

This report describes the bituminous coal deposits of the Olmos Formation (Navarro Group, Upper Cretaceous; Figures 1, 2) of Maverick County in south Texas. Although these were not evaluated quantitatively as part of the current Gulf Coastal Plain coal-resource assessment, a detailed review is presented in this chapter.Prior to the late 1920s, these coal beds were mined underground on a large scale in the vicinity of Eagle Pass, Texas (Figure 1). Since the 1970s, Olmos Formation coals have been mined extensively in both underground and surface mines in nearby Coahuila, Mexico, to supply mine-mouth fuel for power generation at a plant nearby. A tract northeast of Eagle Pass was permitted in the late 1990s for surface mining. In east-central Maverick County, a coalbed methane field is being developed in coal beds of the lower part of the Olmos Formation (Barker et al., 2002; Scott, 2003).

Pelletizing/reslurrying as a means of distributing and firing clean coal. Final quarterly technical progress report No. 5, July 1, 1991--September 30, 1991

DOE Office of Scientific and Technical Information (OSTI.GOV)

Conkle, H.N.; Raghavan, J.K.; Smit, F.J.

1991-11-21

The objective of this study is to develop technology that permits the practical and economic preparation, storage, handling, and transportation of coal pellets, which can be reslurried into Coal water fuels (CWF) suitable for firing in small- and medium-size commercial and industrial boilers, furnaces, and engines. The project includes preparing coal pellets and capsules from wet filter cake that can be economically stored, handled, transported, and reslurried into a CWF that can be suitably atomized and fired at the user site. The wet cakes studied were prepared from ultra-fine (95% -325 mesh) coal beneficiated by advanced froth-flotation techniques. The coalsmore » studied included two eastern bituminous coals, one from Virginia (Elkhorn) and one from Illinois (Illinois No. 6) and one western bituminous coal from Utah (Sky Line coal).« less

Effects of coal storage in air on physical and chemical properties of coal and on gas adsorption

USGS Publications Warehouse

Mastalerz, Maria; Solano-Acosta, W.; Schimmelmann, A.; Drobniak, A.

2009-01-01

This paper investigates changes in the high-volatile bituminous Lower Block Coal Member from Indiana owing to moisture availability and oxidation in air at ambient pressure and temperature over storage time. Specifically, it investigates changes in chemistry, in surface area, and pore structure, as well as changes in methane and carbon dioxide adsorption capacities. Our results document that the methane adsorption capacity increased by 40%, whereas CO2 adsorption capacity increased by 18% during a 13-month time period. These changes in adsorption are accompanied by changes in chemistry and surface area of the coal. The observed changes in adsorption capacity indicate that special care must be taken when collecting samples and preserving coals until adsorption characteristics are measured in the laboratory. High-pressure isotherms from partially dried coal samples would likely cause overestimation of gas adsorption capacities, lead to a miscalculation of coal-bed methane prospects, and provide deceptively optimistic prognoses for recovery of coal-bed methane or capture of anthropogenic CO2. ?? 2009 Elsevier B.V. All rights reserved.

Numerical study of bituminous coal combustion in a boiler furnace with bottom blowing

NASA Astrophysics Data System (ADS)

Zroychikov, N. A.; Kaverin, A. A.

2016-11-01

Results obtained by the numerical study of a solid fuel combustion scheme with bottom blowing using Ekibastuz and Kuznetsk bituminous coals of different fractional makeup are presented. Furnace chambers with bottom blowing provide high-efficiency combustion of coarse-grain coals with low emissions of nitrogen oxides. Studying such a combustion scheme, identification of its technological capabilities, and its further improvement are topical issues. As the initial object of study, we selected P-57-R boiler plant designed for burning of Ekibastuz bituminous coal in a prismatic furnace with dry-ash (solid slag) removal. The proposed modernization of the furnace involves a staged air inflow under the staggered arrangement of directflow burners (angled down) and bottom blowing. The calculation results revealed the specific aerodynamics of the flue gases, the trajectories of solid particles in the furnace chamber, and the peculiarities of the fuel combustion depending on the grinding fineness. It is shown that, for coal grinding on the mill, the overall residue on the screen plate of 90 µm ( R 90 ≤ 27% for Ekibastuz coal and R 90 ≤ 15% for Kuznetsk coal) represents admissible values for fuel grind coarsening in terms of economic efficiency and functional reliability of a boiler. The increase in these values leads to the excess of regulatory heat losses and unburned combustible losses. It has been established that the change in the grade of the burned coal does not significantly affect the flow pattern of the flue gases, and the particles trajectory is essentially determined by the elemental composition of the fuel.

Phenols as chemical fossils in coals. [Book chapter

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bimer, J.; Given, P.H.; Raj, S.

It is generally considered that vitrinite, the principal maceral in most coals, represents coalified, partly decayed wood. Hence lignin should be one of the important precursors to the vitrinites in coals. Accordingly, it would be interesting to know whether any chemical fossils related to lignin could be found in coals. The purpose of this paper is to report what we believe to be a successful search for such fossils. The experimental approach exploited a degradation reaction developed in a study of soil humic acids by Burges et al. This reaction involves a reductive degradation with sodium amalgam and hot water.more » Thin layer chromatography of the ether soluble part of the product (yield, about 20%) showed the presence of a number of phenols and phenolic acids, most of whose structures bore obvious relationships to known microbial and chemical degradation products of lignin but some to the A ring of flavonoids. Humic acids can be extracted from peats and lignites but not from bituminous coals. However, oxidation of bituminous coals with aqueous performic acid generates in high yield (80 to 110% by weight) materials that closely resemble humic acids. The Burges reductive degradation was applied to humic acids extracted from some peats and lignites, and produced by oxidation of a number of bituminous coals. A number of identifications of products were made originally by gas chromatography with co-injection of standards. In this preliminary publication the experimental procedures are described and a sufficient selection of the data are given to show what was found by co-injection and later confirmed by mass spectrometry.« less

Intrinsic and extrinsic defects in a family of coal-derived graphene quantum dots

NASA Astrophysics Data System (ADS)

Singamaneni, Srinivasa Rao; van Tol, Johan; Ye, Ruquan; Tour, James M.

2015-11-01

In this letter, we report on the high frequency (239.2 and 336 GHz) electron spin resonance (ESR) studies performed on graphene quantum dots (GQDs), prepared through a wet chemistry route from three types of coal: (a) bituminous, (b) anthracite, and (c) coke; and from non-coal derived GQDs. The microwave frequency-, power-, and temperature-dependent ESR spectra coupled with computer-aided simulations reveal four distinct magnetic defect centers. In bituminous- and anthracite-derived GQDs, we have identified two of them as intrinsic carbon-centered magnetic defect centers (a broad signal of peak to peak width = 697 (10-4 T), g = 2.0023; and a narrow signal of peak to peak width = 60 (10-4 T), g = 2.003). The third defect center is Mn2+ (6S5/2, 3d5) (signal width = 61 (10-4 T), g = 2.0023, Aiso = 93(10-4 T)), and the fourth defect is identified as Cu2+ (2D5/2, 3d9) (g⊥ = 2.048 and g‖ = 2.279), previously undetected. Coke-derived and non-coal derived GQDs show Mn2+ and two-carbon related signals, and no Cu2+ signal. The extrinsic impurities most likely originate from the starting coal. Furthermore, Raman, photoluminescence, and ESR measurements detected no noticeable changes in the properties of the bituminous GQDs after one year. This study highlights the importance of employing high frequency ESR spectroscopy in identifying the (magnetic) defects, which are roadblocks for spin relaxation times of graphene-based materials. These defects would not have been possible to probe by other spin transport measurements.

Mercury capture by selected Bulgarian fly ashes: Influence of coal rank and fly ash carbon pore structure on capture efficiency

USGS Publications Warehouse

Kostova, I.J.; Hower, J.C.; Mastalerz, Maria; Vassilev, S.V.

2011-01-01

Mercury capture by fly ash C was investigated at five lignite- and subbituminous-coal-burning Bulgarian power plants (Republika, Bobov Dol, Maritza East 2, Maritza East 3, and Sliven). Although the C content of the ashes is low, never exceeding 1.6%, the Hg capture on a unit C basis demonstrates that the low-rank-coal-derived fly ash carbons are more efficient in capturing Hg than fly ash carbons from bituminous-fired power plants. While some low-C and low-Hg fly ashes do not reveal any trends of Hg versus C, the 2nd and, in particular, the 3rd electrostatic precipitator (ESP) rows at the Republika power plant do have sufficient fly ash C range and experience flue gas sufficiently cool to capture measurable amounts of Hg. The Republika 3rd ESP row exhibits an increase in Hg with increasing C, as observed in other power plants, for example, in Kentucky power plants burning Appalachian-sourced bituminous coals. Mercury/C decreases with an increase in fly ash C, suggesting that some of the C is isolated from the flue gas stream and does not contribute to Hg capture. Mercury capture increases with an increase in Brunauer-Emmett-Teller (BET) surface area and micropore surface area. The differences in Hg capture between the Bulgarian plants burning low-rank coal and high volatile bituminous-fed Kentucky power plants suggests that the variations in C forms resulting from the combustion of the different ranks also influence the efficiency of Hg capture. ?? 2010 Elsevier Ltd.

Characterizing thermogenic coalbed gas from Polish coals of different ranks by hydrous pyrolysis

USGS Publications Warehouse

Kotarba, M.J.; Lewan, M.D.

2004-01-01

To provide a better characterization of origin and volume of thermogenic gas generation from coals, hydrous pyrolysis experiments were conducted at 360??C for 72 h on Polish coals ranging in rank from lignite (0.3% R r) to semi-anthracite (2.0% Rr). Under these conditions, the lignites attained a medium-volatile bituminous rank (1.5% Rr), high-volatile bituminous coals attained a low-volatile bituminous rank (1.7% Rr), and the semi-anthracite obtained an anthracite rank (4.0% R r). Hydrous pyrolysis of a coal, irrespective of rank, provides a diagnostic ??13C value for its thermogenic hydrocarbon gases. This value can be used quantitatively to interpret mixing of indigenous thermogenic gas with microbial methane or exogenous thermogenic gas from other sources. Thermogenic methane quantities range from 20 dm3/kg of lignite (0.3% Rr) to 0.35 dm3/kg of semi-anthracite (2.0% Rr). At a vitrinite reflectance of 1.7% Rr, approximately 75% of the maximum potential for a coal to generate thermogenic methane has been expended. At a vitrinite reflectance of 1.7% Rr, more than 90% of the maximum potential for a coal to generate CO2 has been expended. Assuming that these quantities of generated CO2 remain associated with a sourcing coal bed as uplift or erosion provide conditions conducive for microbial methanogenesis, the resulting quantities of microbial methane generated by complete CO2 reduction can exceed the quantities of thermogenic methane generated from the same coal bed by a factor of 2-5. ?? 2004 Elsevier Ltd. All rights reserved.

Regulation of coal polymer degradation by fungi. Tenth Quartery report, October 1996--December 1996

DOE Office of Scientific and Technical Information (OSTI.GOV)

Irvine, R.L.; Bumpus, J.A.

1997-01-28

It has long been known that low rank coal such as leonardite can be solubilized by strong base (>pH 12). Recent discoveries have also shown that leonardite is solubilized by Lewis bases at considerably lower pH values and by fungi that secrete certain Lewis bases (i.e., oxalate ion). During the current reporting period we have studied the ability of a strong base (sodium hydroxide, pH 12), and two fungi, Phanerochaete chrysosporium and Trametes versicolor, to solubilize Argonne Premium Coals. In general, Argonne Premium Coals were relatively resistant to base mediated solubilization. However, when these coals were preoxidized (150{degrees}C for sevenmore » days), substantial amounts of several coals were solubilized. Most affected were the Lewiston-Stockton bituminous coal, the Beulah-Zap lignite, the Wyodak-Anderson subbituminous coal and the Blind Canyon bituminous coal. Argonne Premium Coals were previously shown by us to be relatively resistant to solubilization by sodium oxalate. When preoxidized coals were treated with sodium oxalate, only the Beulah-Zap lignite was substantially solubilized. Although very small amounts of the other preoxidized coals were solubilized by treatment with oxalate, the small amount of solubilization that did take place was generally increased relative to that observed for coals that were not preoxidized. None of the Argonne Premium Coals were solubilized by P. chrysosporium or T. versicolor. Of considerable interest, however, is the observation that P. chrysosporium and T. versicolor mediated extensive solubilization of Lewiston-Stockton bituminous coal, the Beulah-Zap lignite and the Wyodak-Anderson subbituminous coal.« less

Investigation of hot mix asphalt mixtures at Mn/ROAD : final report

DOT National Transportation Integrated Search

1997-02-01

This report presents the material characterization for the Minnesota Road Research Project (Mn/ROAD) bituminous materials. This effort will provide the historical base line information on properties needed for the validation of future pavement evalua...

The evaluation of pavement patching materials in Oregon : final report.

DOT National Transportation Integrated Search

1980-11-01

This report describes the installation and evaluation of trial pavement patching materials in Oregon. The patches were placed in Portland cement concrete and bituminous concrete pavements and evaluated for periods ranging from four to twelve months. ...

Virginia method for the design of dense-graded emulsion mixes.

DOT National Transportation Integrated Search

1982-01-01

An investigation into the Illinois method for the design of dense-graded emulsion base mixes had resulted in a report offering several modifications to that procedure. The Bituminous Research Advisory Committee then recommended that the Illinois meth...

Overlay design method based on visual pavement distress.

DOT National Transportation Integrated Search

1978-01-01

A method for designing the thickness of overlays for bituminous concrete pavements in Virginia is described. In this method the thickness is calculated by rating the amount and severity of observed pavement distress and determining the total accumula...

Performance of protective coatings on structural plate pipe arches.

DOT National Transportation Integrated Search

1978-01-01

The performance of bituminous coatings on structural plate pipe and pipe arches was evaluated in a limited field study supplemented by a survey of information from other agencies. Of the two available application techniques, immersion of individual p...

Assessment of AASHTO M 364 type II and type IV joint sealers.

DOT National Transportation Integrated Search

2014-11-01

To address the issue of water infiltration and debris retention, bituminous crack sealers and fillers have been : developed to help prevent premature pavement distress. If applied appropriately, crack sealers and fillers can : significantly extend th...

ANALYSIS OF RESIDENTIAL COAL STOVE EMISSIONS

EPA Science Inventory

The report gives results of an evaluation, in cooperation with the State of Vermont's Agency of Environmental Conservation, of emissions generated by anthracite and bituminous coal used for residential heating. A residential coal stove was operated with both coals, while comparin...

Use of discarded tires in highway construction.

DOT National Transportation Integrated Search

1980-01-01

In August 1978, bituminous surface treatments in which vulcanized rubber was blended with the asphalt cement were placed on two secondary roads by the Sahuaro Petroleum and Asphalt Company and the Whitehurst Paving Company. The work was jointly finan...

Minnesota's experience with scrap shingles in bituminous pavements

DOT National Transportation Integrated Search

1996-10-01

The Minnesota Department of Transportation (Mn/DOT) has experimented with the use of shingle scrap in hot mix asphalt (HMA) since 1990. To date, the source of the shingle scrap has been shingle manufacturers exclusively. The manufactured shingle scra...

Evaluation of lignin as an antioxidant in asphalt binders and bituminous mixtures : technical summary.

DOT National Transportation Integrated Search

2017-01-01

The chemical process of oxidative age-hardening in asphalt pavements is one of the major distresses leading to hot mix asphalt (HMA) pavement failure as evidenced by fatigue and thermal (low temperature) cracking.

Stripping potential of bituminous concrete.

DOT National Transportation Integrated Search

1978-01-01

Laboratory data were gathered with a newly developed stripping test in anticipation that the test would be adopted for use by the Department. In addition to providing experience in the performance of the test and interpretation of test results, the i...

Evaluation of strains in bituminous surfaces : stiffness-fatigue investigation.

DOT National Transportation Integrated Search

1973-01-01

The study was designed to determine if strains in Virginia's thin asphaltic pavements were high enough to cause early fatigue failure. Strains were computed with the Chevron multilayer computer program, and also measured on selected highways using el...

Use of expanded clay aggregate in bituminous construction.

DOT National Transportation Integrated Search

1959-01-01

In an effort to find a solution to the shortage of aggregate, for use in highway construction, Louisiana Department of Highways initiated a study. : In early 1955, we started experimenting with expanded aggregate or lightweight aggregate as commonly ...

Active methods of mercury removal from flue gases.

PubMed

Marczak, Marta; Budzyń, Stanisław; Szczurowski, Jakub; Kogut, Krzysztof; Burmistrz, Piotr

2018-03-23

Due to its adverse impact on health, as well as its global distribution, long atmospheric lifetime and propensity for deposition in the aquatic environment and in living tissue, the US Environmental Protection Agency (US EPA) has classified mercury and its compounds as a severe air quality threat. Such widespread presence of mercury in the environment originates from both natural and anthropogenic sources. Global anthropogenic emission of mercury is evaluated at 2000 Mg year -1 . According to the National Centre for Emissions Management (Pol. KOBiZE) report for 2014, Polish annual mercury emissions amount to approximately 10 Mg. Over 90% of mercury emissions in Poland originate from combustion of coal.The purpose of this paper was to understand mercury behaviour during sub-bituminous coal and lignite combustion for flue gas purification in terms of reduction of emissions by active methods. The average mercury content in Polish sub-bituminous coal and lignite was 103.7 and 443.5 μg kg -1 . The concentration of mercury in flue gases emitted into the atmosphere was 5.3 μg m -3 for sub-bituminous coal and 17.5 μg m -3 for lignite. The study analysed six low-cost sorbents with the average achieved efficiency of mercury removal from 30.6 to 92.9% for sub-bituminous coal and 22.8 to 80.3% for lignite combustion. Also, the effect of coke dust grain size was examined for mercury sorptive properties. The fine fraction of coke dust (CD) adsorbed within 243-277 μg Hg kg -1 , while the largest fraction at only 95 μg Hg kg -1 . The CD fraction < 0.063 mm removed almost 92% of mercury during coal combustion, so the concentration of mercury in flue gas decreased from 5.3 to 0.4 μg Hg m -3 . The same fraction of CD had removed 93% of mercury from lignite flue gas by reducing the concentration of mercury in the flow from 17.6 to 1.2 μg Hg m -3 . The publication also presents the impact of photochemical oxidation of mercury on the effectiveness of Hg vapour removal during combustion of lignite. After physical oxidation of Hg in the flue gas, its effectiveness has increased twofold.

Selected annotated bibliography of the geology of uraniferous and radioactive native bituminous substances, exclusive of coals, in the United States

USGS Publications Warehouse

Jones, Harriet Nell

1956-01-01

Native bituminous substances are divided into two groups, 1) bitumens and, 2) pyrobitumens. Bitumens are composed principally of hydrocarbons substantially free from oxygenated bodies, are fusible, and are soluble in carbon disulfide. Native bitumens occur in liquid and solid forms. The native liquid bitumens include all petroleums or crude oils. Native solid bitumens include native waxes such as ozocerite, asphalts or petroleum tars, and asphaltites such as gilsonite and grahamite. Pyrobitumens are composed principally of hydrocarbons which may contain oxygenated bodies. They are infusible and are insoluble, or nearly insoluble, in carbon disulfide. Native pyrobitumens are divided into an oxygen-containing group including peats, lignites, and coals, and an essentially oxygen-free, asphaltic group including such substances as wurtzilite, albertite, impsonite, and ingramite. Thucholites, which are carbonaceous substances that may contain uranium, thorium, and rare earths, commonly are considered to be pyrobitumens. Their compositions are variable and may fall into either the oxygen-containing or oxygen-free group. All varieties of native bituminous substances may be associated with mineral matter. The nomenclature of bitumens and pyrobitumens is used very loosely in the literature. This circumstance arises from the difficulty in recognizing many of these substances by visual examination, and because many of them can be identified accurately only by chemical methods. Inasmuch as some of the chemical procedures are time-consuming and satisfactory analytical methods have not been devised for all these substances, geologists generally have not obtained precise identifications but rather have used names that appeared most appropriate to the circumstances. It is expected that future research will show many substances called "asphaltite," "thucholite," etc., to be incorrectly identified. The nomenclature used by the authors of the various references of this bibliography is followed without deviation or further discussion. The stratigraphic nomenclature also is that used by the authors. In this bibliography emphasis is placed on reports dealing with the uranium contents and radioactivity of native bituminous substances rather than on mineralogical and chemical studies of these substances. The distribution of the substances described in the references is shown on the accompanying map. The indicated presence of these substances does not infer that they contain sufficient radioactive elements to constitute ores.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Malhotra, Vivak

The USA is embarking upon tackling the serious environmental challenges posed to the world by greenhouse gases, especially carbon dioxide (CO2). The dimension of the problem is daunting. In fact, according to the Energy Information Agency, nearly 6 billion metric tons of CO2 were produced in the USA in 2007 with coal-burning power plants contributing about 2 billion metric tons. To mitigate the concerns associated with CO2 emission, geological sequestration holds promise. Among the potential geological storage sites, unmineable coal seams and shale formations in particular show promise because of the probability of methane recovery while sequestering the CO2. However.more » the success of large-scale sequestration of CO2 in coal and shale would hinge on a thorough understanding of CO2's interactions with host reservoirs. An important parameter for successful storage of CO2 reservoirs would be whether the pressurized CO2 would remain invariant in coal and shale formations under reasonable internal and/or external perturbations. Recent research has brought to the fore the potential of induced seismicity, which may result in caprock compromise. Therefore, to evaluate the potential risks involved in sequestering CO2 in Illinois bituminous coal seams and shale, we studied: (i) the mechanical behavior of Murphysboro (Illinois) and Houchin Creek (Illinois) coals, (ii) thermodynamic behavior of Illinois bituminous coal at - 100oC ≤ T ≤ 300oC, (iii) how high pressure CO2 (up to 20.7 MPa) modifies the viscosity of the host, (iv) the rate of emission of CO2 from Illinois bituminous coal and shale cores if the cores, which were pressurized with high pressure (≤ 20.7 MPa) CO2, were exposed to an atmospheric pressure, simulating the development of leakage pathways, (v) whether there are any fractions of CO2 stored in these hosts which are resistance to emission by simply exposing the cores to atmospheric pressure, and (vi) how compressive shockwaves applied to the coal and shale cores, which were pressurized with high pressure CO2, determine the fate of sequestered CO2 in these cores. Our results suggested that Illinois bituminous coal in its unperturbed state, i.e., when not pressurized with CO2, showed large variations in the mechanical properties. Modulus varied from 0.7 GPa to 3.4 GPa even though samples were extracted from a single large chunk of coal. We did not observe any glass transition for Illinois bituminous coal at - 100oC ≤ T ≤ 300oC, however, when the coal was pressurized with CO2 at ambient ≤ P ≤ 20.7 MPa, the viscosity of the coal decreased and inversely scaled with the CO2 pressure. The decrease in viscosity as a function of pressure could pose CO2 injection problems for coal as lower viscosity would allow the solid coal to flow to plug the fractures, fissures, and cleats. Our experiments also showed a very small fraction of CO2 was absorbed in coal; and when CO2 pressurized coals were exposed to atmospheric conditions, the loss of CO2 from coals was massive. Half of the sequestered gas from the coal cores was lost in less than 20 minutes. Our shockwave experiments on Illinois bituminous coal, New Albany shale (Illinois), Devonian shale (Ohio), and Utica shale (Ohio) presented clear evidence that the significant emission of the sequestered CO2 from these formations cannot be discounted during seismic activity, especially if caprock is compromised. It is argued that additional shockwave studies, both compressive and transverse, would be required for successfully mapping the risks associated with sequestering high pressure CO2 in coal and shale formations.« less

Review and analysis of Hamburg Wheel Tracking Device test data : [technical summary].

DOT National Transportation Integrated Search

2014-02-01

Approximately 89% of the paved-road network in Kansas is asphalt surfaced (bituminous and : composite). According to the Kansas Department of Transportation (KDOT), typical design : performance period of hot-mix asphalt (HMA) pavement for new constru...

An evaluation of interlayer stress absorbing composite (ISAC) reflective crack relief system

DOT National Transportation Integrated Search

2005-03-01

Reflective cracking of bituminous concrete overlays has long been a problem in pavement rehabilitation. Various types of interlayer systems and fabrics have been used to eliminate or slow the development of reflective cracks. These methods and produc...

32 CFR 643.35 - Policy-Mineral leasing on lands controlled by the Department of the Army.

Code of Federal Regulations, 2010 CFR

2010-07-01

... lease deposits of coal, phosphate, oil, oil shale, gas, sodium, potassium and sulfur which are within..., oil, oil shale, native asphalt, solid and semi-solid bitumen, bituminous rock and gas located on...

32 CFR 643.35 - Policy-Mineral leasing on lands controlled by the Department of the Army.

Code of Federal Regulations, 2012 CFR

2012-07-01

... lease deposits of coal, phosphate, oil, oil shale, gas, sodium, potassium and sulfur which are within..., oil, oil shale, native asphalt, solid and semi-solid bitumen, bituminous rock and gas located on...

32 CFR 643.35 - Policy-Mineral leasing on lands controlled by the Department of the Army.

Code of Federal Regulations, 2013 CFR

2013-07-01

... lease deposits of coal, phosphate, oil, oil shale, gas, sodium, potassium and sulfur which are within..., oil, oil shale, native asphalt, solid and semi-solid bitumen, bituminous rock and gas located on...

32 CFR 643.35 - Policy-Mineral leasing on lands controlled by the Department of the Army.

Code of Federal Regulations, 2011 CFR

2011-07-01

... lease deposits of coal, phosphate, oil, oil shale, gas, sodium, potassium and sulfur which are within..., oil, oil shale, native asphalt, solid and semi-solid bitumen, bituminous rock and gas located on...

32 CFR 643.35 - Policy-Mineral leasing on lands controlled by the Department of the Army.

Code of Federal Regulations, 2014 CFR

2014-07-01

... lease deposits of coal, phosphate, oil, oil shale, gas, sodium, potassium and sulfur which are within..., oil, oil shale, native asphalt, solid and semi-solid bitumen, bituminous rock and gas located on...

Detection of recycled asphalt pavement (RAP) in bituminous mixtures

DOT National Transportation Integrated Search

2004-06-01

The overall goal of this study was to assist the Illinois Department of Transportation (IDOT) in identifying and developing methods for quality assurance of hot-mix asphalt (HMA) containing recycled asphalt pavement (RAP). Although the use of RAP can...

Evaluation of lignin as an antioxidant in asphalt binders and bituminous mixtures.

DOT National Transportation Integrated Search

2017-01-01

The chemical process of oxidative age-hardening in asphalt pavements is one of the major distresses : leading to hot mix asphalt (HMA) pavement failure as evidenced by fatigue and thermal (low temperature) : cracking. : Research investigations at the...

76 FR 79485 - Interstate Land Sales Registration Program (Regulations J, K, and L)

Federal Register 2010, 2011, 2012, 2013, 2014

2011-12-21

... means restrictions that are enforceable by the lot owners and are designed to control the use of the lot... standards. For purposes of this exemption, paved means concrete or pavement with a bituminous surface that...

The Performance Evaluation of Single Pass Thin Lift Bituminous Overlays

DOT National Transportation Integrated Search

1992-06-01

In the mid-1980s, the Illinois Department of Transportation (IDOT) found itself challenged to maintain an aging highway network at an acceptable level of service on a limited financial base. This made programming rehabilitations for the rural highway...

Laboratory investigation of hydrated lime as an antistripping additive : final report.

DOT National Transportation Integrated Search

1983-01-01

The purpose of this laboratory study was to determine the effectiveness of hydrated lime as an antistripping additive when used in bituminous mixes incorporating aggregates frequently used in such mixes in Virginia. The application of 1% hydrated lim...

Nontraditional Fog Seal for Asphalt Pavement : Performance on Shoulder Sections in Minnesota

DOT National Transportation Integrated Search

2018-05-01

The pavement engineering community has recently been introduced to a number of nontraditional products intended for uses as surface sealers for bituminous pavements. Many new products use agricultural-based components and little is known regarding th...

Evaluation of the fundamental engineering properties of bituminous mixtures containing hydrated lime.

DOT National Transportation Integrated Search

2002-04-01

The increasing volume of truck traffic combined with the hot and moist climate of Louisiana are the major contributing factors to severe pavement distresses. Permanent deformation and moisture damage are the most common distresses of Louisiana paveme...

Thin bonded P.C.C. resurfacing : final report.

DOT National Transportation Integrated Search

1982-06-01

After the successful experimentation in Iowa with thin-bonded concrete overlays as an alternative to bituminous overlay, the Louisiana DOTD decided to resurface a short section of US 61, north of Baton Rouge, using this technique during April 1981. T...

Performance of an unbonded concrete overlay on I-74

DOT National Transportation Integrated Search

2002-04-01

In Illinois, the typical rehabilitation for a concrete pavement is full-depth patching of the distressed concrete, and overlaying the pavement with 3.25 inches of bituminous concrete. In cases where there are poor joints or extensive durability crack...

MEASUREMENT OF MERCURY IN CHINESE UTILITY COAL

EPA Science Inventory

The paper gives results of analyzing representative samples of 20 Chinese utility coals for mercury content, and proximate, ultimate, and heating values. The data for these bituminous coals, obtained from China with the cooperation of the Chinese University of Mining Technology,...

Enhanced Combustion Low NOx Pulverized Coal Burner

DOE Office of Scientific and Technical Information (OSTI.GOV)

David Towle; Richard Donais; Todd Hellewell

2007-06-30

For more than two decades, Alstom Power Inc. (Alstom) has developed a range of low cost, infurnace technologies for NOx emissions control for the domestic U.S. pulverized coal fired boiler market. This includes Alstom's internally developed TFS 2000{trademark} firing system, and various enhancements to it developed in concert with the U.S. Department of Energy. As of the date of this report, more than 270 units representing approximately 80,000 MWe of domestic coal fired capacity have been retrofit with Alstom low NOx technology. Best of class emissions range from 0.18 lb/MMBtu for bituminous coal to 0.10 lb/MMBtu for subbituminous coal, withmore » typical levels at 0.24 lb/MMBtu and 0.13 lb/MMBtu, respectively. Despite these gains, NOx emissions limits in the U.S. continue to ratchet down for new and existing boiler equipment. On March 10, 2005, the Environmental Protection Agency (EPA) announced the Clean Air Interstate Rule (CAIR). CAIR requires 25 Eastern states to reduce NOx emissions from the power generation sector by 1.7 million tons in 2009 and 2.0 million tons by 2015. Low cost solutions to meet such regulations, and in particular those that can avoid the need for a costly selective catalytic reduction system (SCR), provide a strong incentive to continue to improve low NOx firing system technology to meet current and anticipated NOx control regulations. The overall objective of the work is to develop an enhanced combustion, low NOx pulverized coal burner, which, when integrated with Alstom's state-of-the-art, globally air staged low NOx firing systems will provide a means to achieve: Less than 0.15 lb/MMBtu NOx emissions when firing a high volatile Eastern or Western bituminous coal, Less than 0.10 lb/MMBtu NOx emissions when firing a subbituminous coal, NOx reduction costs at least 25% lower than the costs of an SCR, Validation of the NOx control technology developed through large (15 MWt) pilot scale demonstration, and Documentation required for economic evaluation and commercial application. During the project performance period, Alstom performed computational fluid dynamics (CFD) modeling and large pilot scale combustion testing in its Industrial Scale Burner Facility (ISBF) at its U.S. Power Plant Laboratories facility in Windsor, Connecticut in support of these objectives. The NOx reduction approach was to optimize near-field combustion to ensure that minimum NOx emissions are achieved with minimal impact on unburned carbon in ash, slagging and fouling, corrosion, and flame stability/turn-down. Several iterations of CFD and combustion testing on a Midwest coal led to an optimized design, which was extensively combustion tested on a range of coals. The data from these tests were then used to validate system costs and benefits versus SCR. Three coals were evaluated during the bench-scale and large pilot-scale testing tasks. The three coals ranged from a very reactive subbituminous coal to a moderately reactive Western bituminous coal to a much less reactive Midwest bituminous coal. Bench-scale testing was comprised of standard ASTM properties evaluation, plus more detailed characterization of fuel properties through drop tube furnace testing and thermogravimetric analysis. Bench-scale characterization of the three test coals showed that both NOx emissions and combustion performance are a strong function of coal properties. The more reactive coals evolved more of their fuel bound nitrogen in the substoichiometric main burner zone than less reactive coal, resulting in the potential for lower NOx emissions. From a combustion point of view, the more reactive coals also showed lower carbon in ash and CO values than the less reactive coal at any given main burner zone stoichiometry. According to bench-scale results, the subbituminous coal was found to be the most amenable to both low NOx, and acceptably low combustibles in the flue gas, in an air staged low NOx system. The Midwest bituminous coal, by contrast, was predicted to be the most challenging of the three coals, with the Western bituminous coal predicted to behave in-between the subbituminous coal and the Midwest bituminous coal. CFD modeling was used to gain insight into the mechanisms governing nozzle tip performance with respect to NOx emissions. The CFD simulations were run as steady state, turbulent, non-reacting flow with heat transfer and focused on predicting the near field mixing and particle dispersion rates. CFD results were used to refine the proposed tip concepts before they were built, as well as to help identify and evaluate possible improvements to the tips for subsequent test weeks.« less

Intergarted geophysical investigations by GPR and ERT on the largest rock fill dam in Europe: Monte Cotugno dam (Southern Italy)

NASA Astrophysics Data System (ADS)

Loperte, A.; Bavusi, M.; Cerverizzo, G.; Lapenna, V.; Soldovieri, F.

2012-04-01

This work is concerned with the first results of a survey based on the integration of geophysical techniques for the inspection of the Monte Cotugno dam, the largest rock fill dam in Europe. The Monte Cotugno dam, managed by National Irrigation Development and Agrarian Transformation in Puglia, Basilicata and Irpinia is located on the Sinni river (Basilicata District, South Italy) and represents the nodal point in the whole hydraulic system on the Ionic side of Italy; in fact, the dam allows harnessing of the Sinni river water for agricultural, industrial, drinking and domestic purposes. The dam is of the zoned type and consists of a central core in sandy silt and of gravelly-sandy shoulders; its water tightness is ensured by a bituminous conglomerate facing on the upstream side, welded at the bottom to the foundation sealing system. The latter is about 1,900m long and consist of a massive concrete cut-off wall based on the marly-clay formation, 300m long on the right and 600 m long on the left side. On the valley bottom it is made up of a reinforced concrete cut-off wall that is inserted in the marly-clay formation and is surmounted by an inspection and percolation water collection tunnel. The watertight face consists of a bottom levelling layer 7-8 cm thick in semi open-graded bituminous concrete, a 5 cm separation layer in dense-graded bituminous concrete, a drainage layer in very open-graded concrete varying in thickness from 10 to 16 cm from the top of the dam down, two 4-cm top layers in dense-graded bituminous concrete with stepped joints, a finishing sealing coat containing 1.5 kg/cm2 of asphalt. The shallowest part of this layering is started to show incipient small detachments due to thermal solicitations; these detachments represent a possible way for water infiltration in the dam. In this framework, it was decided to perform the identification, characterization and evaluation of the potential loss of water through small cracks in the bituminous concrete dam and then monitor these areas of infiltration. For such a task, the use of conventional geotechnical investigation methods was discarded since these techniques often requires invasive actions in the inner of the structure to be investigated (destructiveness) and only provide punctual information for small volumes. On the contrary, in this case, it was decided to use non-invasive sensing techniques, which make it possible to investigate and gain "global" information about all the structure without affecting its operability. In particular, Ground Penetrating Radar and Electrical Resistivity Tomography techniques have been exploited so to have possibility of quickly investigating large portions of dam with different spatial and resolution scales and without the need of destructive actions. The results of this survey well agree with direct surveys and the details of the survey and of the diagnostic results will be shown at the conference.

Evaluation of open-graded friction course mixture : technical assistance report.

DOT National Transportation Integrated Search

2004-10-01

Open-graded friction course (OGFC) is a porous, gap-graded, predominantly single size aggregate bituminous mixture that contains a high percentage of air voids. The high air void content and the open structure of this mix promote the effective draina...

Installation report : evaluation of recycled hot mix asphaltic concrete on Route 220.

DOT National Transportation Integrated Search

1982-01-01

This report describes a project in which the bituminous pavement on an approximately 8-mi. (13-km) section of roadway was removed, recycled through a conventional asphalt batch plant, and relaid. The project was accomplished with little difficulty an...

40 CFR 60.251 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... continuously monitor relative particulate matter loadings. (c) Bituminous coal means solid fossil fuel... units constructed, reconstructed, or modified on or before May 27, 2009, all solid fossil fuels... § 60.17). (2) For units constructed, reconstructed, or modified after May 27, 2009, all solid fossil...

40 CFR 60.251 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... continuously monitor relative particulate matter loadings. (c) Bituminous coal means solid fossil fuel... units constructed, reconstructed, or modified on or before May 27, 2009, all solid fossil fuels... § 60.17). (2) For units constructed, reconstructed, or modified after May 27, 2009, all solid fossil...

40 CFR 60.251 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... continuously monitor relative particulate matter loadings. (c) Bituminous coal means solid fossil fuel... units constructed, reconstructed, or modified on or before May 27, 2009, all solid fossil fuels... § 60.17). (2) For units constructed, reconstructed, or modified after May 27, 2009, all solid fossil...

40 CFR 60.251 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... continuously monitor relative particulate matter loadings. (c) Bituminous coal means solid fossil fuel... units constructed, reconstructed, or modified on or before May 27, 2009, all solid fossil fuels... § 60.17). (2) For units constructed, reconstructed, or modified after May 27, 2009, all solid fossil...

40 CFR 60.251 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... continuously monitor relative particulate matter loadings. (c) Bituminous coal means solid fossil fuel... units constructed, reconstructed, or modified on or before May 27, 2009, all solid fossil fuels... § 60.17). (2) For units constructed, reconstructed, or modified after May 27, 2009, all solid fossil...

The use of fabric reinforced overlays to control reflection cracking of composite pavements.

DOT National Transportation Integrated Search

1973-01-01

Fabric reinforcement was used in an attempt to prevent reflection cracking of two bituminous concrete layers overlying an 8-inch plain (unreinforced, unjointed) concrete base that was underlain by a portland cement stabilized subbase material. On the...

Field evaluation of skid resistant surfaces : final report : part I.

DOT National Transportation Integrated Search

1970-06-01

This project was undertaken to establish a thin bituminous surface course that would possess good skid resistant qualities as well as, being both economical and durable. : This is the final report on the evaluation of skid resistant surfaces which wa...

Evaluation of temperature effects on bituminous pavement deflections in Virginia.

DOT National Transportation Integrated Search

1976-01-01

Eight satellite projects with asphaltic layer thicknesses varying from 3.5 inches (88 mm) to 13.5 inches (338 mm) were tested for dynaflect deflections during the four seasons of 1974-75. The projects were located throughout Virginia. The evaluation ...

Geochemistry of highly basic calcium hydroxide groundwater in Jordan

USGS Publications Warehouse

Barnes, I.; Presser, T.S.; Saines, M.; Dickson, P.; Van Groos, A. F. K.

1982-01-01

Highly-alkaline (pH > 12.5) meteoric waters of a Ca2+OH--type issue from naturally calcined bituminous marl. The cold (16.5 ??? T(??C) ??? 19.1) waters are super-saturated with minerals thought to be of high-temperature origin. ?? 1982.

Thin bonded P.C.C. resurfacing : interim report No. 1.

DOT National Transportation Integrated Search

1982-06-01

After the successful experimentation in Iowa with thin-bonded concrete overlays as an alternative to bituminous overlay, the Louisiana DOTD decided to resurface a short section of US 61, north of Baton Rouge, using this technique during April 1981. T...

Expanded clay hot mix study : final report: part I.

DOT National Transportation Integrated Search

1969-04-01

This is part I of a two part final report on expanded clay hot mix to: (1) evaluate the use of various expanded clay bituminous mixtures under high traffic counts, (2) accumulate through experience testing, suitable information on the physical proper...

Establishing layer coefficients for CTB, PMBB, and RAP.

DOT National Transportation Integrated Search

1991-09-01

In 1988, the Oregon State Highway Division adopted the 1986 AASHTO guide for pavement thickness design. Currently the OSHD uses a layer coefficient of .22 to .24 for cement treated base (CTB), and .32 for plant mix bituminous base (PMBB). Recycled as...

Single-coal-particle combustion in O{sub 2}/N{sub 2} and O{sub 2}/CO{sub 2} environments

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bejarano, Paula A.; Levendis, Yiannis A.

A fundamental investigation has been conducted on the combustion of single particles of a bituminous coal (45-53, 75-90, and 150-180 {mu}m), of a lignite coal (45-53 and 75-90 {mu}m), and of spherical and monodisperse synthetic chars (43 {mu}m) at increasing O{sub 2} mole fractions in either N{sub 2} or CO{sub 2} balance gases. The synthetic particles were used to facilitate the observation of combustion phenomena with minimum distractions from particle-to-particle variabilities. The laboratory setup consisted of a drop-tube furnace operated at temperatures of 1400 and 1600 K. A calibrated three-color pyrometer, interfaced with the furnace, recorded luminous particle temperature-time profiles.more » Experimental results revealed that coal particles burned at higher mean temperatures and shorter combustion times in O{sub 2}/N{sub 2} than in O{sub 2}/CO{sub 2} environments at analogous oxygen mole fractions. In the case of the bituminous coal used herein and for the experimental combustion conditions tested, measured volatile and char temperatures as in air (21% O{sub 2}) were attained with an oxygen content in the CO{sub 2} mixtures in the neighborhood of 30%. Bituminous coal volatile and char burnout times comparable to those in air (21% O{sub 2}) were attained with oxygen content in the CO{sub 2} mixtures in the range of 30-35%. In the case of the lignite coal burned, the corresponding differences in oxygen mole fractions, which result in similar particle temperatures and burnout times in the two different gas mixtures, were less pronounced. (author)« less

Devolatilization of coal particles in a flat flame -- Experimental and modeling study

DOE Office of Scientific and Technical Information (OSTI.GOV)

Therssen, E.; Gourichon, L.; Delfosse, L.

1995-10-01

Pulverized coals have been tested under the conditions of industrial flames, with high heating rate and high temperatures. The chars were collected after different pyrolysis times. For eight coals, the devolatilized fraction of coal has been measured, as well as those of carbon, hydrogen and nitrogen. During pyrolysis, the evolution of the texture of the grains has been studied by measurement of their microporous surface area, which undergoes a large increase, depending on coal rank. The composition of the volatiles, as deduced from the ultimate and proximate analysis of chars, showed high volatile bituminous coals to essentially produce tars withmore » an aromatic structure. Low and medium volatile bituminous coals produced light hydrocarbons on devolatilization and the char`s surface area continued increasing slowly during the whole of devolatilization, according to the slow increase of the fraction of hydrogen devolatilized. The char`s reactivity with oxygen was followed by measurements of Active Surface Area (ASA). It was shown that the ASA continuously decreases during devolatilization. Five models of devolatilization in the literature were tested and compared to the experimental results, assuming first-order reactions with respect to the remaining volatile matter. Badzioch`s model correctly fitted the experimental results and values of the rate constant obtained by computer trial and error adjustment were higher for lower ranks of the four bituminous coals. Anthony`s model also fits the measurements, provided an adjustment of the preexponential factor of activation energy for which it is shown that an infinite number of such pairs is suitable. If the model is run isothermally at the flame`s peak temperature, it also correctly fits the experimental results.« less

Studies of the fate of sulfur trioxide in coal-fired utility boilers based on modified selected condensation methods.

PubMed

Cao, Yan; Zhou, Hongcang; Jiang, Wu; Chen, Chien-Wei; Pan, Wei-Ping

2010-05-01

The formation of sulfur trioxide (SO(3)) in coal-fired utility boilers can have negative effects on boiler performance and operation, such as fouling and corrosion of equipment, efficiency loss in the air preheater (APH), increase in stack opacity, and the formation of PM(2.5). Sulfur trioxide can also compete with mercury when bonding with injected activated carbons. Tests in a lab-scale reactor confirmed there are major interferences between fly ash and SO(3) during SO(3) sampling. A modified SO(3) procedure to maximize the elimination of measurement biases, based on the inertial-filter-sampling and the selective-condensation-collecting of SO(3), was applied in SO(3) tests in three full-scale utility boilers. For the two units burning bituminous coal, SO(3) levels starting at 20 to 25 ppmv at the inlet to the selective catalytic reduction (SCR), increased slightly across the SCR, owing to catalytic conversion of SO(2) to SO(3,) and then declined in other air pollutant control device (APCD) modules downstream to approximately 5 ppmv and 15 ppmv at the two sites, respectively. In the unit burning sub-bituminous coal, the much lower initial concentration of SO(3) estimated to be approximately 1.5 ppmv at the inlet to the SCR was reduced to about 0.8 ppmv across the SCR and to about 0.3 ppmv at the exit of the wet flue gas desulfurization (WFGD). The SO(3) removal efficiency across the WFGD scrubbers at the three sites was generally 35% or less. Reductions in SO(3) across either the APH or the dry electrostatic precipitator (ESP) in units burning high-sulfur bituminous coal were attributed to operating temperatures being below the dew point of SO(3).

Distribution of potentially hazardous trace elements in coals from Shanxi province, China

USGS Publications Warehouse

Zhang, J.Y.; Zheng, C.G.; Ren, D.Y.; Chou, C.-L.; Liu, J.; Zeng, R.-S.; Wang, Z.P.; Zhao, F.H.; Ge, Y.T.

2004-01-01

Shanxi province, located in the center of China, is the biggest coal base of China. There are five coal-forming periods in Shanxi province: Late Carboniferous (Taiyuan Formation), Early Permian (Shanxi Formation), Middle Jurassic (Datong Formation), Tertiary (Taxigou Formation), and Quaternary. Hundred and ten coal samples and a peat sample from Shanxi province were collected and the contents of 20 potentially hazardous trace elements (PHTEs) (As, B, Ba, Cd, Cl, Co, Cr, Cu, F, Hg, Mn, Mo, Ni, Pb, Sb, Se, Th, U, V and Zn) in these samples were determined by instrumental neutron activation analysis, atomic absorption spectrometry, cold-vapor atomic absorption spectrometry, ion chromatography spectrometry, and wet chemical analysis. The result shows that the brown coals are enriched in As, Ba, Cd, Cr, Cu, F and Zn compared with the bituminous coals and anthracite, whereas the bituminous coals are enriched in B, Cl, Hg, and the anthracite is enriched in Cl, Hg, U and V. A comparison with world averages and crustal abundances (Clarke values) shows that the Quaternary peat is highly enriched in As and Mo, Tertiary brown coals are highly enriched in Cd, Middle Jurassic coals, Early Permian coals and Late Carboniferous coals are enriched in Hg. According to the coal ranks, the bituminous coals are highly enriched in Hg, whereas Cd, F and Th show low enrichments, and the anthracite is also highly enriched in Hg and low enrichment in Th. The concentrations of Cd, F, Hg and Th in Shanxi coals are more than world arithmetic means of concentrations for the corresponding elements. Comparing with the United States coals, Shanxi coals show higher concentrations of Cd, Hg, Pb, Se and Th. Most of Shanxi coals contain lower concentrations of PHTEs. ?? 2004 Elsevier Ltd. All rights reserved.

Characteristics of Pyrolytic Topping in Fluidized Bed for Different Volatile Coals

NASA Astrophysics Data System (ADS)

Xiong, R.; Dong, L.; Xu, G. W.

Coal is generally combusted or gasified directly to destroy completely the chemical structures, such as aromatic rings containing in volatile coals including bituminite and lignite. Coal topping refers to a process that extracts chemicals with aromatic rings from such volatile coals in advance of combustion or gasification and thereby takes advantage of the value of coal as a kind of chemical structure resource. CFB boiler is the coal utilization facility that can be easily retrofitted to implement coal topping. A critical issue for performing coal topping is the choice of the pyrolytic reactor that can be different types. The present study concerns fluidized bed reactor that has rarely been tested for use in coal topping. Two different types of coals, one being Xiaolongtan (XLT) lignite and the other Shanxi (SX) bituminous, were tested to clarify the yield and composition of pyrolysis liquid and gas under conditions simulating actual operations. The results showed that XLT lignite coals had the maximum tar yield in 823-873K and SX bituminite realized its highest tar yield in 873-923K. Overall, lignite produced lower tar yield than bituminous coal. The pyrolysis gas from lignite coals contained more CO and CO2 and less CH4, H2 and C2+C3 (C2H4, C2H6, C3H6, C3H8) components comparing to that from bituminous coal. TG-FTIR analysis of tars demonstrated that for different coals there are different amounts of typical chemical species. Using coal ash of CFB boiler, instead of quartz sand, as the fluidized particles decreased the yields of both tar and gas for all the tested coals. Besides, pyrolysis in a reaction atmosphere simulating the pyrolysis gas (instead of N2) resulted also in higher production of pyrolysis liquid.

Update on coal in Big Horn basin, Montana and Wyoming

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jones, R.W.

1983-08-01

The Big Horn Coal basin is located within the topographic and structural basin of the same name and is defined by the limits of the Upper Cretaceous Mesaverde Formation in northwestern Wyoming and the Eagle Sandstone in south-central Montana. The coal in this basin ranges in rank from high volatile C bituminous (based primarily on resistance to weathering) to subbituminous B coal. In general, the Mesaverde and Eagle coals are highest in heat content, averaging over 10,500 Btu/lb; the Fort Union coals in the Red Lodge-Bear Creek and Grass Creek fields average about 10,200 Btu/lb and are second highest inmore » heating value. The Meeteetse Formation contains coals that average 9,800 Btu/lb, the lowest heating values in the basin. An average heating value for all coal in the basin is slightly less than 10,000 But/lb. The average sulfur content of all coals in this basin is less than 1%, with a range of 0.4 to 2.2%. Coal mining in the Big Horn Coal basin began in the late 1880s in the Red Lodge field and has continued to the present. Almost 53 million tons of coal have been mined in the basin; nearly 78% of this production (41 million tons) is from bituminous Fort Union coal beds in the Red Lodge-Bear Creek and Bridger coal fields, Montana. Original in-place resources for the Big Horn Coal basin are given by rank of coal: 1,265.12 million tons of bituminous coal resources have been calculated for the Silvertip field, Wyoming, and the Red Lodge-Bear Creek and Bridger fields, Montana; 563.78 million tons of subbituminous resources have been calculated for the remaining Wyoming coal fields.« less

Development of non-petroleum-based binders for use in flexible pavements - phase II.

DOT National Transportation Integrated Search

2015-10-01

Bio-binders can be utilized as asphalt modifiers, extenders, and replacements for conventional asphalt in bituminous binders. : From the rheology results of Phase I of this project, it was found that the bio-binders tested had good performance, simil...

Efforts to reduce reflective cracking of bituminous concrete overlays of Portland cement concrete pavements.

DOT National Transportation Integrated Search

1975-01-01

Studies of efforts in Virginia to reduce the incidence of reflection cracking when portland cement concrete pavements or bases are overlayed with asphaltic concrete are reported. The methods of reflection crack reduction discussed are: (1) The use of...

Utilization of western coal fly ash in construction of highways in the Midwest

DOT National Transportation Integrated Search

2000-03-01

Coal burning utilities in the Midwest are increasingly using sub-bituminous coal from Wyoming. These utilities typically produce fly ash, which, because of its high calcium oxide content, may be classified as Class C fly ash. These ashes are characte...

49 CFR 387.301 - Surety bond, certificate of insurance, or other securities.

Code of Federal Regulations, 2010 CFR

2010-10-01

... in bulk. Cement, building blocks. Charcoal. Chemical fertilizer. Cinder blocks. Cinders, coal. Coal. Coke. Commercial fertilizer. Concrete materials and added mixtures. Corn cobs. Cottonseed hulls... nitrate of soda. Anhydrous ammonia—used as a fertilizer only. Ashes, wood or coal. Bituminous concrete...

40 CFR 63.14 - Incorporations by reference.

Code of Federal Regulations, 2014 CFR

2014-07-01

... Testing and Materials (ASTM), 100 Barr Harbor Drive, Post Office Box C700, West Conshohocken, PA 19428... (Reapproved 2010), Standard Test Method for Water in Petroleum Products and Bituminous Materials by...-09 Standard Test Method for Heat of Combustion of Liquid Hydrocarbon Fuels by Bomb Calorimeter...

Investigation of fatigue failure in bituminous base mixes.

DOT National Transportation Integrated Search

1980-01-01

A correlation between the results obtained with the fatigue test and those from the indirect tensile test on two base mixes was attempted in anticipation of the possible use of the latter test to design base mixes for maximum fatigue life. Two base m...

Collective Bargaining and Labor-Management Relations in 1988.

ERIC Educational Resources Information Center

Ruben, George

1989-01-01

Reviews labor contracts renegotiated during 1988, placing emphasis on labor-management relations. Provides information on negotiations in the following industries: (1) trucking, (2) air transportation, (3) automobile manufacturing, (4) steel and other metals, (5) rubber, (6) bituminous coal, (7) forest products, and (8) shipbuilding. Covers…

The influence of thickness on density of an I-2 bituminous mix.

DOT National Transportation Integrated Search

1978-01-01

From this very limited study, it was concluded that (1) even when the road cross section was distorted, the contractor did an excellent job of controlling the average application rate; (2) the percent compaction, while acceptably high, did not increa...

Compaction of bituminous concrete with self-propelled pneumatic tire rollers in Louisiana.

DOT National Transportation Integrated Search

1958-10-01

The main objective of this investigation was to study the possibilities of improving the density of asphaltic concrete pavements at the time of construction to approach the values obtained during the first year of traffic service, in order to elimina...

A Factorial Design Approach to Analyse the Effect of Coarse Recycled Concrete Aggregates on the Properties of Hot Mix Asphalt

NASA Astrophysics Data System (ADS)

Tanty, Kiranbala; Mukharjee, Bibhuti Bhusan; Das, Sudhanshu Shekhar

2018-06-01

The present study investigates the effect of replacement of coarse fraction of natural aggregates by recycled concrete aggregates on the properties of hot mix asphalt (HMA) using general factorial design approach. For this two factors i.e. recycled coarse aggregates percentage [RCA (%)] and bitumen content percentage [BC (%)] are considered. Tests have been carried out on the HMA type bituminous concrete, prepared with varying RCA (%) and BC (%). Analysis of variance has been performed on the experimental data to determine the effect of the chosen factors on various parameters such as stability, flow, air void, void mineral aggregate, void filled with bitumen and bulk density. The study depicts that RCA (%) and BC (%) have significant effect on the selected responses as p value is less than the chosen significance level. In addition to above, the outcomes of the statistical analysis indicate that interaction between factors have significant effects on void mineral aggregate and bulk density of bituminous concrete.

Market assessment of PFBC ash use

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bland, A. E.; Brown, T. H., Western Research Institute

1998-01-01

Pressurized fluidized bed combustion (PFBC) of coal is undergoing demonstration in the United States, as well as throughout the world. American Electric Power`s (AEP`s) bubbling PFBC 70 MWe Tidd demonstration program in Ohio and pilot-scale development at Foster Wheeler Energia Oy 10 MWth circulating PFBC at Karhula, Finland, have demonstrated the advantages of PFBC technology. Further technology development in the US is planned with the deployment of the technology at the MacIntosh Clean Coal project in Lakeland, Florida. Development of uses for solid wastes from PFBC coal-fired power systems is being actively pursued as part of the demonstration of PFBCmore » technologies. Ashes collected from Foster Wheeler Energia Oy pilot circulating PFBC tests in Karhula, Finland, operating on (1) low sulfur subbituminous and (2) high sulfur bituminous coal; and ash from the AEP`s high-sulfur bituminous coal-fired bubbling PFBC in Brilliant, Ohio, were evaluated in laboratory and pilot-scale ash use testing at Western Research Institute (WRI).« less

Carbon dioxide from coal combustion: Variation with rank of US coal

USGS Publications Warehouse

Quick, J.C.; Glick, D.C.

2000-01-01

Carbon dioxide from combustion of US coal systematically varies with ASTM rank indices, allowing the amount of CO2 produced per net unit of energy to be predicted for individual coals. No single predictive equation is applicable to all coals. Accordingly, we provide one equation for coals above high volatile bituminous rank and another for lower rank coals. When applied to public data for commercial coals from western US mines these equations show a 15% variation of kg CO2 (net GJ)-1. This range of variation suggests reduction of US CO2 emissions is possible by prudent selection of coal for combustion. Maceral and mineral content are shown to slightly affect CO2 emissions from US coal. We also suggest that CO2 emissions increased between 6 and 8% in instances where Midwestern US power plants stopped burning local, high-sulfur bituminous coal and started burning low-sulfur, subbituminous C rank coal from the western US.

A Factorial Design Approach to Analyse the Effect of Coarse Recycled Concrete Aggregates on the Properties of Hot Mix Asphalt

NASA Astrophysics Data System (ADS)

Tanty, Kiranbala; Mukharjee, Bibhuti Bhusan; Das, Sudhanshu Shekhar

2018-02-01

The present study investigates the effect of replacement of coarse fraction of natural aggregates by recycled concrete aggregates on the properties of hot mix asphalt (HMA) using general factorial design approach. For this two factors i.e. recycled coarse aggregates percentage [RCA (%)] and bitumen content percentage [BC (%)] are considered. Tests have been carried out on the HMA type bituminous concrete, prepared with varying RCA (%) and BC (%). Analysis of variance has been performed on the experimental data to determine the effect of the chosen factors on various parameters such as stability, flow, air void, void mineral aggregate, void filled with bitumen and bulk density. The study depicts that RCA (%) and BC (%) have significant effect on the selected responses as p value is less than the chosen significance level. In addition to above, the outcomes of the statistical analysis indicate that interaction between factors have significant effects on void mineral aggregate and bulk density of bituminous concrete.

Coal char oxidation kinetics in air medium

NASA Astrophysics Data System (ADS)

Slyusarskiy, K. V.; Jankovskiy, S. A.; Korotkikh, A. G.; Sorokin, I. V.

2017-01-01

Research on oxidation in air medium process of three different coal chars with various carbon content was presented. The anthracite, T-grade bituminous coal and 2B-grade lignite char powders with particle size less than 80 µm were studied. The coal char oxidation was studied by isothermal method using coupled TG-DSC analyzer Netzsch STA 449 Jupiter F3 in the temperature range 1000-1200 °C. Experiments were carried out at ambient pressure. Volumetric flow rate of oxidation medium into analyzer chamber was 250 ml/min and consisted of oxygen and argon with volumetric ratio 24:1. Based on experimental data, the average rate of carbon oxidation reaction values were defined at each temperature. Kinetic constants (frequency factor and activation energy) of reaction were defined as well via 1st order Arrhenius equation. Activation energy values are in good agreement with the data presented in the literature. Activation energy values for anthracite char are 1.6-1.7 times higher than those for bituminous coal and lignite chars, respectively.

Enhancement of Cr(VI) Ion Removal Using Nanochitosan Coated on Bituminous Activated Carbon.

PubMed

Chooaksorn, Wanida; Nitisoravut, Rachnarin; Polprasert, Chongrak; Babel, Sandhya; Laohhasurayotin, Kritapas; Kangwansupamonkon, Wiyong

2016-11-01

  Bituminous activated carbon (AC) has been widely used as a sorbent for adsorption of non-polar species, but its performance for removal of ionic species such as heavy metals has not been as efficient. In this study, AC was modified with chitosan nanoparticles (CN) using facile methods of dip coating and wet impregnation. The CN-coated AC demonstrated an increase in Cr(VI) removal efficiency in both kinetics and adsorption capacity. The adsorption capacity of the CN-coated AC (mg/g) was more than twice that of the uncoated AC (36.36 mg/g), or pure chitosan (32.57 mg/g). The sizes of the synthesized CN (160-2,000 nm) can be controlled by varying the concentration of the chitosan/reagents used. The adsorption isotherms are better described using the Freundlich rather than the Langmuir model and are in agreement with the heterogeneity of the surfaces. Adsorption kinetics followed that of the pseudo-second-order kinetics, suggesting chemisorption as a rate limiting step.

Study on co-pyrolysis characteristics of rice straw and Shenfu bituminous coal blends in a fixed bed reactor.

PubMed

Li, Shuaidan; Chen, Xueli; Liu, Aibin; Wang, Li; Yu, Guangsuo

2014-03-01

Co-pyrolysis behaviors of rice straw and Shenfu bituminous coal were studied in a fixed bed reactor under nitrogen atmosphere. The pyrolysis temperatures were 700°C, 800°C and 900°C, respectively. Six different biomass ratios were used. Gas, tar components were analyzed by a gas chromatograph and a gas chromatography-mass spectrometry respectively. Under co-pyrolysis conditions, the gas volume yields are higher than the calculated values. Co-pyrolysis tar contains more phenolics, less oxygenate compounds than calculated values. The addition of biomass changes the atmosphere during the pyrolysis process and promotes tar decomposition. The SEM results show that the differences between the blended char and their parents char are not significant. The results of char yields and ultimate analysis also show that no significant interactions exist between the two kinds of particles. The changes of gas yield and components are caused by the secondary reactions and tar decomposition. Copyright © 2014 Elsevier Ltd. All rights reserved.

Combustion characteristics of Malaysian oil palm biomass, sub-bituminous coal and their respective blends via thermogravimetric analysis (TGA).

PubMed

Idris, Siti Shawalliah; Rahman, Norazah Abd; Ismail, Khudzir

2012-11-01

The combustion characteristics of Malaysia oil palm biomass (palm kernel shell (PKS), palm mesocarp fibre (PMF) and empty fruit bunches (EFB)), sub-bituminous coal (Mukah Balingian) and coal/biomass blends via thermogravimetric analysis (TGA) were investigated. Six weight ratios of coal/biomass blends were prepared and oxidised under dynamic conditions from temperature 25 to 1100°C at four heating rates. The thermogravimetric analysis demonstrated that the EFB and PKS evolved additional peak besides drying, devolatilisation and char oxidation steps during combustion. Ignition and burn out temperatures of blends were improved in comparison to coal. No interactions were observed between the coal and biomass during combustion. The apparent activation energy during this process was evaluated using iso-conversional model free kinetics which resulted in highest activation energy during combustion of PKS followed by PMF, EFB and MB coal. Blending oil palm biomass with coal reduces the apparent activation energy value. Copyright © 2012 Elsevier Ltd. All rights reserved.

Co-gasification of bituminous coal and hydrochar derived from municipal solid waste: Reactivity and synergy.

PubMed

Wei, Juntao; Guo, Qinghua; He, Qing; Ding, Lu; Yoshikawa, Kunio; Yu, Guangsuo

2017-09-01

In this work, the influences of gasification temperature and blended ratio on co-gasification reactivity and synergy of Shenfu bituminous coal (SF) and municipal solid waste-derived hydrochar (HTC) were investigated using TGA. Additionally, active alkaline and alkaline earth metal (AAEM) transformation during co-gasification was quantitatively analyzed by inductively coupled plasma optical emission spectrometer for correlating synergy on co-gasification reactivity. The results showed that higher char gasification reactivity existed at higher HTC char proportion and gasification temperature, and the main synergy behaviour on co-gasification reactivity was performed as synergistic effect. Enhanced synergistic effect at lower temperature was mainly resulted from more obviously inhibiting the primary AAEM (i.e. active Ca) transformation, and weak synergistic effect still existed at higher temperature since more active K with prominent catalysis was retained. Furthermore, more active HTC-derived AAEM remaining in SF sample during co-gasification would lead to enhanced synergistic effect as HTC char proportion increased. Copyright © 2017 Elsevier Ltd. All rights reserved.

10 CFR 766.103 - Special Assessment invoices.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 10 Energy 4 2011-01-01 2011-01-01 false Special Assessment invoices. 766.103 Section 766.103 Energy DEPARTMENT OF ENERGY URANIUM ENRICHMENT DECONTAMINATION AND DECOMMISSIONING FUND; PROCEDURES FOR SPECIAL ASSESSMENT OF DOMESTIC UTILITIES Procedures for Special Assessment § 766.103 Special Assessment...

10 CFR 766.103 - Special Assessment invoices.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 10 Energy 4 2014-01-01 2014-01-01 false Special Assessment invoices. 766.103 Section 766.103 Energy DEPARTMENT OF ENERGY URANIUM ENRICHMENT DECONTAMINATION AND DECOMMISSIONING FUND; PROCEDURES FOR SPECIAL ASSESSMENT OF DOMESTIC UTILITIES Procedures for Special Assessment § 766.103 Special Assessment...

10 CFR 766.103 - Special Assessment invoices.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 10 Energy 4 2012-01-01 2012-01-01 false Special Assessment invoices. 766.103 Section 766.103 Energy DEPARTMENT OF ENERGY URANIUM ENRICHMENT DECONTAMINATION AND DECOMMISSIONING FUND; PROCEDURES FOR SPECIAL ASSESSMENT OF DOMESTIC UTILITIES Procedures for Special Assessment § 766.103 Special Assessment...

34 CFR 300.18 - Highly qualified special education teachers.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 34 Education 2 2010-07-01 2010-07-01 false Highly qualified special education teachers. 300.18... SPECIAL EDUCATION AND REHABILITATIVE SERVICES, DEPARTMENT OF EDUCATION ASSISTANCE TO STATES FOR THE... special education teachers. (a) Requirements for special education teachers teaching core academic...

PULMONARY TOXICITY OF SIZE-CLASSIFIED COAL FLY ASH PARTICLES OF VARYING CARBON CONTENT

EPA Science Inventory

Epidemiological studies have shown that morbidity and mortality increase along with concentration of particulate matter (PM) in many different countries and regions despite great variations in the chemical makeup of the PM. In this study, Illinois bituminous coal with high sulfur...

Filtration of micron-sized particles for coal liquids: carbonaceous precoats. [5 refs

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rodgers, B.R.

Carbonaceous precoats, such as bituminous coal and char from hydrocarbonization, are shown to be effective, inexpensive substitutes for traditional diatomaceous earth materials, both at laboratory-scale and bench-scale. Model equations are developed for filtration of Solvent Refined Coal-Unfiltered Oil (SRC-UFO).

30 CFR 71.2 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... is located. (g) MRE instrument means the gravimetric dust sampler with a four channel horizontal... in the earth by any means or method, and the work of preparing the coal so extracted, including... bituminous coal, lignite, or anthracite from its natural deposits underground by any means or method, and the...

Experimental use of sawed and sealed joints to minimize thermal cracking : interim report - third year.

DOT National Transportation Integrated Search

2001-09-01

Saw and Seal is the process of introducing uniformly spaced saw joints to a bituminous : overlay in an attempt to eliminate or retard the formation of thermal and /or reflective : cracking. : Saw and Seal technology has been experimented with f...

VARIATION OF ELEMENT SPECIATION IN COAL COMBUSTION AEROSOLS WITH PARTICLE SIZE

EPA Science Inventory

The speciation of sulfur, iron and key trace elements (Cr, As, Se, Zn) in combustion ash aerosols has been examined as a function of size from experimental combustion units burning Utah and Illinois bituminous coals. Although predominantly present as sulfate, sulfur was also pre...

14 CFR 151.77 - Runway paving: General rules.

Code of Federal Regulations, 2010 CFR

2010-01-01

... project include pavement construction and reconstruction, and include runway grooving to improve skid... course to correct major irregularities in the pavement. Runway resealing or refilling joints as an... Specification P-609) on a pavement the current surface of which consists of that kind of a bituminous surface...

14 CFR 151.77 - Runway paving: General rules.

Code of Federal Regulations, 2011 CFR

2011-01-01

... project include pavement construction and reconstruction, and include runway grooving to improve skid... course to correct major irregularities in the pavement. Runway resealing or refilling joints as an... Specification P-609) on a pavement the current surface of which consists of that kind of a bituminous surface...

14 CFR 151.77 - Runway paving: General rules.

Code of Federal Regulations, 2012 CFR

2012-01-01

... project include pavement construction and reconstruction, and include runway grooving to improve skid... course to correct major irregularities in the pavement. Runway resealing or refilling joints as an... Specification P-609) on a pavement the current surface of which consists of that kind of a bituminous surface...

14 CFR 151.77 - Runway paving: General rules.

Code of Federal Regulations, 2014 CFR

2014-01-01

... project include pavement construction and reconstruction, and include runway grooving to improve skid... course to correct major irregularities in the pavement. Runway resealing or refilling joints as an... Specification P-609) on a pavement the current surface of which consists of that kind of a bituminous surface...

14 CFR 151.77 - Runway paving: General rules.

Code of Federal Regulations, 2013 CFR

2013-01-01

... project include pavement construction and reconstruction, and include runway grooving to improve skid... course to correct major irregularities in the pavement. Runway resealing or refilling joints as an... Specification P-609) on a pavement the current surface of which consists of that kind of a bituminous surface...

Experimental use of sawed and sealed joints to minimize thermal cracking : final report - August 2004.

DOT National Transportation Integrated Search

2004-08-01

Saw and Seal is the process of introducing uniformly spaced saw joints to a bituminous overlay in an : attempt to eliminate or retard the formation of thermal and /or reflective cracking. : Saw and Seal technology has been experimented with for...

Full depth bituminous recycling of I-70, Thomas County, Kansas

DOT National Transportation Integrated Search

2004-01-01

In 1990, 13 full depth asphalt pavement test sections were built on a portion of I-70 in Thomas County, Kansas. Various combinations of hot mix and cold recycle mixes with different additives were used to build the test sections. Two of the test sect...

Control of reflection cracking in a fabric-reinforced overlay on jointed portland cement concrete pavement.

DOT National Transportation Integrated Search

1982-01-01

A study of the installation and three-year performance evaluation of a fabric-reinforced bituminous concrete overlay of a jointed concrete pavement is reported. The fabric, a polypropylene in an asphaltic mastic, was shown to act as a significant det...

Waste tire and shingle scrap/bituminous paving test sections on the Munger Recreational Trail Gateway segment. interim report

DOT National Transportation Integrated Search

1991-02-01

The need to reduce Minnesota's dependence on land fills resulted in a unique cooperative venture by three state agencies. A partnership was forged between the Minnesota Pollution Control Agency (MPCA), the Minnesota Department of Natural Resources (D...

38 CFR 21.3104 - Special training.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 38 Pensions, Bonuses, and Veterans' Relief 2 2011-07-01 2011-07-01 false Special training. 21.3104.... Chapter 35 Counseling § 21.3104 Special training. (a) Initial counseling. A counseling psychologist or..., spouse's or surviving spouse's need for a course of specialized vocational training or special...

38 CFR 21.3104 - Special training.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 38 Pensions, Bonuses, and Veterans' Relief 2 2010-07-01 2010-07-01 false Special training. 21.3104.... Chapter 35 Counseling § 21.3104 Special training. (a) Initial counseling. A counseling psychologist or..., spouse's or surviving spouse's need for a course of specialized vocational training or special...

48 CFR 239.7409 - Special assembly.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 48 Federal Acquisition Regulations System 3 2013-10-01 2013-10-01 false Special assembly. 239.7409... Services 239.7409 Special assembly. (a) Special assembly is the designing, manufacturing, arranging... general use equipment. (b) Special assembly rates and charges shall be based on estimated costs. The...

48 CFR 239.7409 - Special assembly.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 48 Federal Acquisition Regulations System 3 2010-10-01 2010-10-01 false Special assembly. 239.7409... Services 239.7409 Special assembly. (a) Special assembly is the designing, manufacturing, arranging... general use equipment. (b) Special assembly rates and charges shall be based on estimated costs. The...

48 CFR 239.7409 - Special assembly.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 48 Federal Acquisition Regulations System 3 2014-10-01 2014-10-01 false Special assembly. 239.7409... Services 239.7409 Special assembly. (a) Special assembly is the designing, manufacturing, arranging... general use equipment. (b) Special assembly rates and charges shall be based on estimated costs. The...

48 CFR 239.7409 - Special assembly.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 48 Federal Acquisition Regulations System 3 2012-10-01 2012-10-01 false Special assembly. 239.7409... Services 239.7409 Special assembly. (a) Special assembly is the designing, manufacturing, arranging... general use equipment. (b) Special assembly rates and charges shall be based on estimated costs. The...

48 CFR 239.7409 - Special assembly.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 48 Federal Acquisition Regulations System 3 2011-10-01 2011-10-01 false Special assembly. 239.7409... Services 239.7409 Special assembly. (a) Special assembly is the designing, manufacturing, arranging... general use equipment. (b) Special assembly rates and charges shall be based on estimated costs. The...

Roofing research and standards development: Fourth volume. ASTM special technical publication 1349

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wallace, T.J.; Rossiter, W.J. Jr.

1999-07-01

As the roofing industry has stabilized, a broad variety of roof systems have found general acceptance by the building owners, architects, engineers, contractors, and others who select and install roofs. These roof systems include those based on conventional built-up membranes using glass and synthetic reinforcements, synthetic polymeric membranes using elastomers and thermoplastics, polymer-modified membranes, and sprayed polyurethane foam. ASTM Committee D8 on Roofing, Waterproofing, and Bituminous Materials has contributed significantly in many important ways to the roofing community's stabilization including issuing standard specifications to assist consumers in the selection and use of these systems. This is not surprising, as itmore » has always been among the purpose of D8 to provide standards to assist in the selection and use of low-sloped and steep roofing. The Committee's scope includes development of standards associated with application, inspection, maintenance, and analyses. Some of the issues facing the roofing community today--for example, enhanced system durability, better methods of material characterization, environmental impact, recycling of materials and systems, industry conversation to the S.I. system metric--readily fall within D8's scope. The availability of sound standard can contribute to the resolution of many of these issues.« less

30 CFR 75.380 - Escapeways; bituminous and lignite mines.

Code of Federal Regulations, 2014 CFR

2014-07-01

..., ramps, or similar facilities where the escapeways cross over obstructions. (7) Provided with a... specific conditions, which is approved by the district manager. (2) Paragraphs (f)(3) through (f)(7) of... escapeway, except for continuous miners and as provided in paragraphs (f)(5), (f)(6), and (f)(7) of this...

30 CFR 75.380 - Escapeways; bituminous and lignite mines.

Code of Federal Regulations, 2013 CFR

2013-07-01

..., ramps, or similar facilities where the escapeways cross over obstructions. (7) Provided with a... specific conditions, which is approved by the district manager. (2) Paragraphs (f)(3) through (f)(7) of... escapeway, except for continuous miners and as provided in paragraphs (f)(5), (f)(6), and (f)(7) of this...

30 CFR 75.380 - Escapeways; bituminous and lignite mines.

Code of Federal Regulations, 2012 CFR

2012-07-01

..., ramps, or similar facilities where the escapeways cross over obstructions. (7) Provided with a... specific conditions, which is approved by the district manager. (2) Paragraphs (f)(3) through (f)(7) of... escapeway, except for continuous miners and as provided in paragraphs (f)(5), (f)(6), and (f)(7) of this...

Experimental use of sawed and sealed joints to minimize thermal cracking : interim report - second year.

DOT National Transportation Integrated Search

1999-08-01

"Saw and Seal" is the process of introducing uniformly spaced saw joints to a bituminous : overlay in an attempt to eliminate or retard the formation of thermal and /or reflective : cracking. : Saw and Seal technology has been experimented with for m...

38 CFR 39.61 - Site planning standards.

Code of Federal Regulations, 2014 CFR

2014-07-01

... roads shall be generally 24 feet wide. (4) Pavement design. The pavement section of all roads, service areas, and parking areas shall be designed for the maximum anticipated traffic loads and existing soil conditions and in accordance with local and State design criteria. (5) Curbs. Bituminous roads may be...

38 CFR 39.61 - Site planning standards.

Code of Federal Regulations, 2013 CFR

2013-07-01

... roads shall be generally 24 feet wide. (4) Pavement design. The pavement section of all roads, service areas, and parking areas shall be designed for the maximum anticipated traffic loads and existing soil conditions and in accordance with local and State design criteria. (5) Curbs. Bituminous roads may be...

38 CFR 39.61 - Site planning standards.

Code of Federal Regulations, 2012 CFR

2012-07-01

... roads shall be generally 24 feet wide. (4) Pavement design. The pavement section of all roads, service areas, and parking areas shall be designed for the maximum anticipated traffic loads and existing soil conditions and in accordance with local and State design criteria. (5) Curbs. Bituminous roads may be...

38 CFR 39.61 - Site planning standards.

Code of Federal Regulations, 2011 CFR

2011-07-01

... roads shall be generally 24 feet wide. (4) Pavement design. The pavement section of all roads, service areas, and parking areas shall be designed for the maximum anticipated traffic loads and existing soil conditions and in accordance with local and State design criteria. (5) Curbs. Bituminous roads may be...

Laboratory and field evaluations of non-bituminous hot melt pavement marker adhesive Georgia test deck : two year evaluation (fall 2006 product submissions).

DOT National Transportation Integrated Search

2008-10-01

Purpose: : The purpose of the National Transportation Product Evaluation Program (NTPEP) is to provide a cost-effective method of evaluation for materials of common interest among all participating NTPEP member departments. NTPEP reports allow member...

Evaluation of lignin as an antioxidant in asphalt binders and bituminous mixtures : technical summary.

DOT National Transportation Integrated Search

2017-01-01

The objective of this 2007 limited laboratory research project was to determine the potential of reducing the oxidation rate of HMA pavements by adding lignin to the asphalt binder used to produce the HMA mixture. The testing matrix for this study co...

30 CFR 75.380 - Escapeways; bituminous and lignite mines.

Code of Federal Regulations, 2011 CFR

2011-07-01

..., ramps, or similar facilities where the escapeways cross over obstructions. (7) Provided with a... specific conditions, which is approved by the district manager. (2) Paragraphs (f)(3) through (f)(7) of... escapeway, except for continuous miners and as provided in paragraphs (f)(5), (f)(6), and (f)(7) of this...

Defense Energy Support Center Fact Book: Providing Energy Solutions Worldwide

DTIC Science & Technology

2010-04-20

2011.through.fiscal. 2017 .. • Merging.System.Analysis.and.Program. Development.Oil.and.GAS.with.EBS.in.fiscal.2010...Wright.Patterson.Air.Force.Base,.OH Rock.Island.Arsenal,.IL Red.River.Army.Depot,. Texarkana ,.TX Malmstrom.Air.Force.Base,.MT Sub-Bituminous Coal: Ft..Wainwright,.AK

THE EFFECT OF ACTIVATED CARBON SURFACE MOISTURE ON LOW TEMPERATURE MERCURY ADSORPTION

EPA Science Inventory

Experiments with elemental mercury (Hg0) adsorption by activated carbons were performed using a bench-scale fixed-bed reactor at room temperature (27 degrees C) to determine the role of surface moisture in capturing Hg0. A bituminous-coal-based activated carbon (BPL) and an activ...

The stripping of penetration 85-100 asphalt from silicate aggregate rocks : a laboratory study.

DOT National Transportation Integrated Search

1972-01-01

In Virginia stripping has occurred when certain of the acidic silicate rocks have been used as aggregate in bituminous paving. The purpose of this project was to discover which kinds of silicate aggregate would be most apt to remain well bonded in bi...

Dissolved metals and associated constituents in abandoned coal-mine discharges, Pennsylvania, USA. Part 2: Geochemical controls on constituent concentrations

USGS Publications Warehouse

Cravotta, C.A.

2008-01-01

Water-quality data for discharges from 140 abandoned mines in the Anthracite and Bituminous Coalfields of Pennsylvania reveal complex relations among the pH and dissolved solute concentrations that can be explained with geochemical equilibrium models. Observed values of pH ranged from 2.7 to 7.3 in the coal-mine discharges (CMD). Generally, flow rates were smaller and solute concentrations were greater for low-pH CMD samples; pH typically increased with flow rate. Although the frequency distribution of pH was similar for the anthracite and bituminous discharges, the bituminous discharges had smaller median flow rates; greater concentrations of SO4, Fe, Al, As, Cd, Cu, Ni and Sr; comparable concentrations of Mn, Cd, Zn and Se; and smaller concentrations of Ba and Pb than anthracite discharges with the same pH values. The observed relations between the pH and constituent concentrations can be attributed to (1) dilution of acidic water by near-neutral or alkaline ground water; (2) solubility control of Al, Fe, Mn, Ba and Sr by hydroxide, sulfate, and/or carbonate minerals; and (3) aqueous SO4-complexation and surface-complexation (adsorption) reactions. The formation of AlSO4+ and AlHSO42 + complexes adds to the total dissolved Al concentration at equilibrium with Al(OH)3 and/or Al hydroxysulfate phases and can account for 10-20 times greater concentrations of dissolved Al in SO4-laden bituminous discharges compared to anthracite discharges at pH of 5. Sulfate complexation can also account for 10-30 times greater concentrations of dissolved FeIII concentrations at equilibrium with Fe(OH)3 and/or schwertmannite (Fe8O8(OH)4.5(SO4)1.75) at pH of 3-5. In contrast, lower Ba concentrations in bituminous discharges indicate that elevated SO4 concentrations in these CMD sources could limit Ba concentrations by the precipitation of barite (BaSO4). Coprecipitation of Sr with barite could limit concentrations of this element. However, concentrations of dissolved Pb, Cu, Cd, Zn, and most other trace cations in CMD samples were orders of magnitude less than equilibrium with sulfate, carbonate, and/or hydroxide minerals. Surface complexation (adsorption) by hydrous ferric oxides (HFO) could account for the decreased concentrations of these divalent cations with increased pH. In contrast, increased concentrations of As and, to a lesser extent, Se with increased pH could result from the adsorption of these oxyanions by HFO at low pH and desorption at near-neutral pH. Hence, the solute concentrations in CMD and the purity of associated "ochres" formed in CMD settings are expected to vary with pH and aqueous SO4 concentration, with potential for elevated SO4, As and Se in ochres formed at low pH and elevated Cu, Cd, Pb and Zn in ochres formed at near-neutral pH. Elevated SO4 content of ochres could enhance the adsorption of cations at low pH, but decrease the adsorption of anions such as As. Such information on environmental processes that control element concentrations in aqueous samples and associated precipitates could be useful in the design of systems to reduce dissolved contaminant concentrations and/or to recover potentially valuable constituents in mine effluents.

Organic petrology and geochemistry of Eocene Suzak bituminous marl, north-central Afghanistan: Depositional environment and source rock potential

USGS Publications Warehouse

Hackley, Paul C.; Sanfilipo, John

2016-01-01

Organic geochemistry and petrology of Eocene Suzak bituminous marl outcrop samples from Madr village in north-central Afghanistan were characterized via an integrated analytical approach to evaluate depositional environment and source rock potential. Multiple proxies suggest the organic-rich (TOC ∼6 wt.%) bituminous marls are ‘immature’ for oil generation (e.g., vitrinite Ro < 0.4%, Tmax < 425 °C, PI ≤ 0.05, C29 ααα S/S + R ≤ 0.12, C29 ββS/ββS+ααR ≤ 0.10, others), yet oil seeps are present at outcrop and live oil and abundant solid bitumen were observed via optical microscopy. Whole rock sulfur content is ∼2.3 wt.% whereas sulfur content is ∼5.0–5.6 wt.% in whole rock extracts with high polar components, consistent with extraction from S-rich Type IIs organic matter which could generate hydrocarbons at low thermal maturity. Low Fe-sulfide mineral abundance and comparison of Pr/Ph ratios between saturate and whole extracts suggest limited Fe concentration resulted in sulfurization of organic matter during early diagenesis. From these observations, we infer that a Type IIs kerogen in ‘immature’ bituminous marl at Madr could be generating high sulfur viscous oil which is seeping from outcrop. However, oil-seep samples were not collected for correlation studies. Aluminum-normalized trace element concentrations indicate enrichment of redox sensitive trace elements Mo, U and V and suggest anoxic-euxinic conditions during sediment deposition. The bulk of organic matter observed via optical microscopy is strongly fluorescent amorphous bituminite grading to lamalginite, possibly representing microbial mat facies. Short chain n-alkanes peak at C14–C16 (n-C17/n-C29 > 1) indicating organic input from marine algae and/or bacterial biomass, and sterane/hopane ratios are low (0.12–0.14). Monoaromatic steroids are dominated by C28clearly indicating a marine setting. High gammacerane index values (∼0.9) are consistent with anoxia stratification and may indicate intermittent saline-hypersaline conditions. Stable C isotope ratios also suggest a marine depositional scenario for the Suzak samples, consistent with the presence of marine foraminifera including abundant planktic globigerinida(?) and rare benthic discocyclina(?) and nummulites(?). Biomarker 2α-methylhopane for photosynthetic cyanobacteria implies shallow photic zone deposition of Madr marls and 3β-methylhopane indicates presence of methanotrophic archaea in the microbial consortium. The data presented herein are consistent with deposition of Suzak bituminous marls in shallow stratified waters of a restricted marine basin associated with the southeastern incipient or proto-Paratethys. Geochemical proxies from Suzak rock extracts (S content, high polar content, C isotopes, normal (αααR) C27–29 steranes, and C29/C30 and C26/C25 hopane ratios) are similar to extant data from Paleogene oils produced to the north in the Afghan-Tajik Basin. This observation may indicate laterally equivalent strata are effective source rocks as suggested by previous workers; however, further work is needed to strengthen oil-source correlations.

31 CFR 128.23 - Special survey reports.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 31 Money and Finance: Treasury 1 2010-07-01 2010-07-01 false Special survey reports. 128.23... § 128.23 Special survey reports. The Secretary may prescribe special survey reports with respect to.... Notice of special survey reports will be published in accordance with § 128.1(c). ...

48 CFR 1336.270 - Special requirements for ship construction

Code of Federal Regulations, 2010 CFR

2010-10-01

... 48 Federal Acquisition Regulations System 5 2010-10-01 2010-10-01 false Special requirements for ship construction 1336.270 Section 1336.270 Federal Acquisition Regulations System DEPARTMENT OF COMMERCE SPECIAL CATEGORIES OF CONTRACTING CONSTRUCTION AND ARCHITECT-ENGINEER CONTRACTS Special Aspects of Contracting for Construction 1336.270 Special...

17 CFR 200.735-12 - Special Government employees.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 17 Commodity and Securities Exchanges 2 2013-04-01 2013-04-01 false Special Government employees... Employees and Former Members and Employees of the Commission § 200.735-12 Special Government employees. (a) Special Government employee means a person defined in section 18 U.S.C. 202 as a special Government...

17 CFR 200.735-12 - Special Government employees.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 17 Commodity and Securities Exchanges 3 2014-04-01 2014-04-01 false Special Government employees... Employees and Former Members and Employees of the Commission § 200.735-12 Special Government employees. (a) Special Government employee means a person defined in section 18 U.S.C. 202 as a special Government...

31 CFR 344.10 - What are Special Zero Interest securities?

Code of Federal Regulations, 2012 CFR

2012-07-01

... 31 Money and Finance:Treasury 2 2012-07-01 2012-07-01 false What are Special Zero Interest...-STATE AND LOCAL GOVERNMENT SERIES Special Zero Interest Securities § 344.10 What are Special Zero Interest securities? Special zero interest securities were issued as certificates of indebtedness and notes...

31 CFR 344.10 - What are Special Zero Interest securities?

Code of Federal Regulations, 2011 CFR

2011-07-01

... 31 Money and Finance:Treasury 2 2011-07-01 2011-07-01 false What are Special Zero Interest...-STATE AND LOCAL GOVERNMENT SERIES Special Zero Interest Securities § 344.10 What are Special Zero Interest securities? Special zero interest securities were issued as certificates of indebtedness and notes...

5 CFR 9701.361 - Special skills payments.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 5 Administrative Personnel 3 2011-01-01 2011-01-01 false Special skills payments. 9701.361 Section... RESOURCES MANAGEMENT SYSTEM Pay and Pay Administration Special Payments § 9701.361 Special skills payments... at the same time as basic pay or in periodic lump-sum payments. Special skills payments are not basic...

10 CFR 70.42 - Transfer of special nuclear material.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 10 Energy 2 2010-01-01 2010-01-01 false Transfer of special nuclear material. 70.42 Section 70.42 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) DOMESTIC LICENSING OF SPECIAL NUCLEAR MATERIAL Acquisition, Use and Transfer of Special Nuclear Material, Creditors' Rights § 70.42 Transfer of special...

10 CFR 70.41 - Authorized use of special nuclear material.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 10 Energy 2 2012-01-01 2012-01-01 false Authorized use of special nuclear material. 70.41 Section 70.41 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) DOMESTIC LICENSING OF SPECIAL NUCLEAR MATERIAL Acquisition, Use and Transfer of Special Nuclear Material, Creditors' Rights § 70.41 Authorized use of special...

10 CFR 70.41 - Authorized use of special nuclear material.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 10 Energy 2 2011-01-01 2011-01-01 false Authorized use of special nuclear material. 70.41 Section 70.41 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) DOMESTIC LICENSING OF SPECIAL NUCLEAR MATERIAL Acquisition, Use and Transfer of Special Nuclear Material, Creditors' Rights § 70.41 Authorized use of special...

10 CFR 70.42 - Transfer of special nuclear material.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 10 Energy 2 2012-01-01 2012-01-01 false Transfer of special nuclear material. 70.42 Section 70.42 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) DOMESTIC LICENSING OF SPECIAL NUCLEAR MATERIAL Acquisition, Use and Transfer of Special Nuclear Material, Creditors' Rights § 70.42 Transfer of special...

10 CFR 70.42 - Transfer of special nuclear material.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 10 Energy 2 2011-01-01 2011-01-01 false Transfer of special nuclear material. 70.42 Section 70.42 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) DOMESTIC LICENSING OF SPECIAL NUCLEAR MATERIAL Acquisition, Use and Transfer of Special Nuclear Material, Creditors' Rights § 70.42 Transfer of special...

10 CFR 70.41 - Authorized use of special nuclear material.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 10 Energy 2 2014-01-01 2014-01-01 false Authorized use of special nuclear material. 70.41 Section 70.41 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) DOMESTIC LICENSING OF SPECIAL NUCLEAR MATERIAL Acquisition, Use and Transfer of Special Nuclear Material, Creditors' Rights § 70.41 Authorized use of special...

10 CFR 70.42 - Transfer of special nuclear material.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 10 Energy 2 2013-01-01 2013-01-01 false Transfer of special nuclear material. 70.42 Section 70.42 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) DOMESTIC LICENSING OF SPECIAL NUCLEAR MATERIAL Acquisition, Use and Transfer of Special Nuclear Material, Creditors' Rights § 70.42 Transfer of special...

10 CFR 70.42 - Transfer of special nuclear material.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 10 Energy 2 2014-01-01 2014-01-01 false Transfer of special nuclear material. 70.42 Section 70.42 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) DOMESTIC LICENSING OF SPECIAL NUCLEAR MATERIAL Acquisition, Use and Transfer of Special Nuclear Material, Creditors' Rights § 70.42 Transfer of special...

10 CFR 70.41 - Authorized use of special nuclear material.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 10 Energy 2 2013-01-01 2013-01-01 false Authorized use of special nuclear material. 70.41 Section 70.41 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) DOMESTIC LICENSING OF SPECIAL NUCLEAR MATERIAL Acquisition, Use and Transfer of Special Nuclear Material, Creditors' Rights § 70.41 Authorized use of special...

10 CFR 70.41 - Authorized use of special nuclear material.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 10 Energy 2 2010-01-01 2010-01-01 false Authorized use of special nuclear material. 70.41 Section 70.41 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) DOMESTIC LICENSING OF SPECIAL NUCLEAR MATERIAL Acquisition, Use and Transfer of Special Nuclear Material, Creditors' Rights § 70.41 Authorized use of special...

50 CFR 100.19 - Special actions.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 50 Wildlife and Fisheries 8 2011-10-01 2011-10-01 false Special actions. 100.19 Section 100.19... § 100.19 Special actions. (a) Emergency special actions. In an emergency situation, if necessary to... recommendations on the proposed emergency special action. Such a Council recommendation, if any, will be subject...

27 CFR 31.234 - Liability for special (occupational) tax.

Code of Federal Regulations, 2010 CFR

2010-04-01

... special (occupational) tax in accordance with the laws and regulations in effect at that time. The tax... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false Liability for special... Liability for special (occupational) tax. The special (occupational) tax on alcohol beverage dealers was...

20 CFR 702.144 - Purpose of the special fund.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 20 Employees' Benefits 3 2010-04-01 2010-04-01 false Purpose of the special fund. 702.144 Section... Provisions Commutation of Payments and Special Fund § 702.144 Purpose of the special fund. This special fund was established to give effect to a congressional policy determination that, under certain...

5 CFR 9701.363 - Special staffing payments.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 5 Administrative Personnel 3 2010-01-01 2010-01-01 false Special staffing payments. 9701.363 Section 9701.363 Administrative Personnel DEPARTMENT OF HOMELAND SECURITY HUMAN RESOURCES MANAGEMENT... HUMAN RESOURCES MANAGEMENT SYSTEM Pay and Pay Administration Special Payments § 9701.363 Special...

5 CFR 9701.362 - Special assignment payments.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 5 Administrative Personnel 3 2010-01-01 2010-01-01 false Special assignment payments. 9701.362 Section 9701.362 Administrative Personnel DEPARTMENT OF HOMELAND SECURITY HUMAN RESOURCES MANAGEMENT... HUMAN RESOURCES MANAGEMENT SYSTEM Pay and Pay Administration Special Payments § 9701.362 Special...

47 CFR 87.151 - Special requirements for differential GPS receivers.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 47 Telecommunication 5 2010-10-01 2010-10-01 false Special requirements for differential GPS receivers. 87.151 Section 87.151 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) SAFETY AND SPECIAL RADIO SERVICES AVIATION SERVICES Technical Requirements § 87.151 Special requirements for...

14 CFR 25.2 - Special retroactive requirements.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Special retroactive requirements. 25.2... AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY AIRPLANES General § 25.2 Special retroactive requirements. The following special retroactive requirements are applicable to an airplane for which the regulations...

48 CFR 239.7408 - Special construction.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 48 Federal Acquisition Regulations System 3 2013-10-01 2013-10-01 false Special construction. 239.7408 Section 239.7408 Federal Acquisition Regulations System DEFENSE ACQUISITION REGULATIONS SYSTEM... Telecommunications Services 239.7408 Special construction. ...

48 CFR 239.7408 - Special construction.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 48 Federal Acquisition Regulations System 3 2011-10-01 2011-10-01 false Special construction. 239.7408 Section 239.7408 Federal Acquisition Regulations System DEFENSE ACQUISITION REGULATIONS SYSTEM... Telecommunications Services 239.7408 Special construction. ...

31 CFR 128.13 - Special survey reports.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 31 Money and Finance: Treasury 1 2010-07-01 2010-07-01 false Special survey reports. 128.13... Transactions and Positions § 128.13 Special survey reports. The Secretary may prescribe special survey reports... respect to such data. Notice of special survey reports will be published in accordance with § 128.1(c). ...

5 CFR 531.245 - Computing locality rates and special rates for GM employees.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 5 Administrative Personnel 1 2010-01-01 2010-01-01 false Computing locality rates and special... Gm Employees § 531.245 Computing locality rates and special rates for GM employees. Locality rates and special rates are computed for GM employees in the same manner as locality rates and special rates...

13 CFR 310.1 - Special Impact Area.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 13 Business Credit and Assistance 1 2010-01-01 2010-01-01 false Special Impact Area. 310.1 Section... SPECIAL IMPACT AREAS § 310.1 Special Impact Area. Upon the application of an Eligible Recipient, and with... the Project will serve as a Special Impact Area if the Eligible Recipient demonstrates that its...

50 CFR 100.19 - Special actions.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 50 Wildlife and Fisheries 6 2010-10-01 2010-10-01 false Special actions. 100.19 Section 100.19... § 100.19 Special actions. (a) The Board may restrict, close, or reopen the taking of fish and wildlife.... Requests for Special Action that do not meet these conditions will be rejected; however, a rejected Special...

14 CFR Appendix - Special Federal Aviation Regulation No. 60

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 2 2012-01-01 2012-01-01 false Special Federal Aviation Regulation No. 60 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) AIR TRAFFIC AND GENERAL OPERATING RULES SPECIAL AIR TRAFFIC RULES Special Federal Aviation Regulation No. 60...

40 CFR 1042.640 - Special provisions for branded engines.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 32 2010-07-01 2010-07-01 false Special provisions for branded engines. 1042.640 Section 1042.640 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... Special Compliance Provisions § 1042.640 Special provisions for branded engines. The following provisions...

10 CFR 766.107 - Prepayment of future Special Assessments

Code of Federal Regulations, 2014 CFR

2014-01-01

... 10 Energy 4 2014-01-01 2014-01-01 false Prepayment of future Special Assessments 766.107 Section 766.107 Energy DEPARTMENT OF ENERGY URANIUM ENRICHMENT DECONTAMINATION AND DECOMMISSIONING FUND; PROCEDURES FOR SPECIAL ASSESSMENT OF DOMESTIC UTILITIES Procedures for Special Assessment § 766.107...

10 CFR 766.107 - Prepayment of future Special Assessments

Code of Federal Regulations, 2011 CFR

2011-01-01

... 10 Energy 4 2011-01-01 2011-01-01 false Prepayment of future Special Assessments 766.107 Section 766.107 Energy DEPARTMENT OF ENERGY URANIUM ENRICHMENT DECONTAMINATION AND DECOMMISSIONING FUND; PROCEDURES FOR SPECIAL ASSESSMENT OF DOMESTIC UTILITIES Procedures for Special Assessment § 766.107...

10 CFR 766.107 - Prepayment of future Special Assessments

Code of Federal Regulations, 2012 CFR

2012-01-01

... 10 Energy 4 2012-01-01 2012-01-01 false Prepayment of future Special Assessments 766.107 Section 766.107 Energy DEPARTMENT OF ENERGY URANIUM ENRICHMENT DECONTAMINATION AND DECOMMISSIONING FUND; PROCEDURES FOR SPECIAL ASSESSMENT OF DOMESTIC UTILITIES Procedures for Special Assessment § 766.107...

31 CFR 594.310 - Specially designated global terrorist; SDGT.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 31 Money and Finance:Treasury 3 2012-07-01 2012-07-01 false Specially designated global terrorist... (Continued) OFFICE OF FOREIGN ASSETS CONTROL, DEPARTMENT OF THE TREASURY GLOBAL TERRORISM SANCTIONS REGULATIONS General Definitions § 594.310 Specially designated global terrorist; SDGT. The term specially...

31 CFR 594.310 - Specially designated global terrorist; SDGT.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 31 Money and Finance:Treasury 3 2011-07-01 2011-07-01 false Specially designated global terrorist... (Continued) OFFICE OF FOREIGN ASSETS CONTROL, DEPARTMENT OF THE TREASURY GLOBAL TERRORISM SANCTIONS REGULATIONS General Definitions § 594.310 Specially designated global terrorist; SDGT. The term specially...

31 CFR 594.310 - Specially designated global terrorist; SDGT.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 31 Money and Finance:Treasury 3 2013-07-01 2013-07-01 false Specially designated global terrorist... (Continued) OFFICE OF FOREIGN ASSETS CONTROL, DEPARTMENT OF THE TREASURY GLOBAL TERRORISM SANCTIONS REGULATIONS General Definitions § 594.310 Specially designated global terrorist; SDGT. The term specially...

31 CFR 594.310 - Specially designated global terrorist; SDGT.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 31 Money and Finance: Treasury 3 2010-07-01 2010-07-01 false Specially designated global terrorist... (Continued) OFFICE OF FOREIGN ASSETS CONTROL, DEPARTMENT OF THE TREASURY GLOBAL TERRORISM SANCTIONS REGULATIONS General Definitions § 594.310 Specially designated global terrorist; SDGT. The term specially...

31 CFR 594.310 - Specially designated global terrorist; SDGT.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 31 Money and Finance:Treasury 3 2014-07-01 2014-07-01 false Specially designated global terrorist... (Continued) OFFICE OF FOREIGN ASSETS CONTROL, DEPARTMENT OF THE TREASURY GLOBAL TERRORISM SANCTIONS REGULATIONS General Definitions § 594.310 Specially designated global terrorist; SDGT. The term specially...

10 CFR 766.107 - Prepayment of future Special Assessments

Code of Federal Regulations, 2010 CFR

2010-01-01

... 10 Energy 4 2010-01-01 2010-01-01 false Prepayment of future Special Assessments 766.107 Section 766.107 Energy DEPARTMENT OF ENERGY URANIUM ENRICHMENT DECONTAMINATION AND DECOMMISSIONING FUND; PROCEDURES FOR SPECIAL ASSESSMENT OF DOMESTIC UTILITIES Procedures for Special Assessment § 766.107...

38 CFR 21.154 - Special transportation assistance.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 38 Pensions, Bonuses, and Veterans' Relief 2 2011-07-01 2011-07-01 false Special transportation.... Chapter 31 Special Rehabilitation Services § 21.154 Special transportation assistance. (a) General. A veteran, who because of the effects of disability has transportation expenses in addition to those...

38 CFR 21.154 - Special transportation assistance.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 38 Pensions, Bonuses, and Veterans' Relief 2 2012-07-01 2012-07-01 false Special transportation.... Chapter 31 Special Rehabilitation Services § 21.154 Special transportation assistance. (a) General. A veteran, who because of the effects of disability has transportation expenses in addition to those...

38 CFR 21.154 - Special transportation assistance.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 38 Pensions, Bonuses, and Veterans' Relief 2 2014-07-01 2014-07-01 false Special transportation.... Chapter 31 Special Rehabilitation Services § 21.154 Special transportation assistance. (a) General. A veteran, who because of the effects of disability has transportation expenses in addition to those...

47 CFR 87.149 - Special requirements for automatic link establishment (ALE).

Code of Federal Regulations, 2010 CFR

2010-10-01

... 47 Telecommunication 5 2010-10-01 2010-10-01 false Special requirements for automatic link establishment (ALE). 87.149 Section 87.149 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) SAFETY AND SPECIAL RADIO SERVICES AVIATION SERVICES Technical Requirements § 87.149 Special requirements...

47 CFR 1.772 - Application for special tariff permission.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 47 Telecommunication 1 2010-10-01 2010-10-01 false Application for special tariff permission. 1... Complaints, Applications, Tariffs, and Reports Involving Common Carriers Tariffs § 1.772 Application for special tariff permission. Applications under section 203 of the Communications Act for special tariff...

46 CFR 190.01-15 - Special consideration.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 7 2010-10-01 2010-10-01 false Special consideration. 190.01-15 Section 190.01-15 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) OCEANOGRAPHIC RESEARCH VESSELS CONSTRUCTION AND ARRANGEMENT Hull Structure § 190.01-15 Special consideration. (a) Special consideration will...

42 CFR 422.52 - Eligibility to elect an MA plan for special needs individuals.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 42 Public Health 3 2013-10-01 2013-10-01 false Eligibility to elect an MA plan for special needs..., Election, and Enrollment § 422.52 Eligibility to elect an MA plan for special needs individuals. (a) General rule. In order to elect a specialized MA plan for a special needs individual (Special Needs MA...

42 CFR 422.52 - Eligibility to elect an MA plan for special needs individuals.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 42 Public Health 3 2010-10-01 2010-10-01 false Eligibility to elect an MA plan for special needs..., and Enrollment § 422.52 Eligibility to elect an MA plan for special needs individuals. (a) General rule. In order to elect a specialized MA plan for a special needs individual (Special Needs MA plan, or...

42 CFR 422.52 - Eligibility to elect an MA plan for special needs individuals.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 42 Public Health 3 2011-10-01 2011-10-01 false Eligibility to elect an MA plan for special needs..., and Enrollment § 422.52 Eligibility to elect an MA plan for special needs individuals. (a) General rule. In order to elect a specialized MA plan for a special needs individual (Special Needs MA plan, or...

42 CFR 422.52 - Eligibility to elect an MA plan for special needs individuals.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 42 Public Health 3 2014-10-01 2014-10-01 false Eligibility to elect an MA plan for special needs..., Election, and Enrollment § 422.52 Eligibility to elect an MA plan for special needs individuals. (a) General rule. In order to elect a specialized MA plan for a special needs individual (Special Needs MA...

42 CFR 422.52 - Eligibility to elect an MA plan for special needs individuals.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 42 Public Health 3 2012-10-01 2012-10-01 false Eligibility to elect an MA plan for special needs..., Election, and Enrollment § 422.52 Eligibility to elect an MA plan for special needs individuals. (a) General rule. In order to elect a specialized MA plan for a special needs individual (Special Needs MA...

Comparison of Novel Carboneous Structures to Treat Nitroaromatic Impacted Water

DTIC Science & Technology

2015-12-01

MS-15-D-047 Abstract Carboneous materials such as carbon nanotube (CNT), granular activated carbon (GAC), and biochar are promising materials...TECHNOLOGIES ...................................................49 A.3 GRANULAR ACTIVATED CARBON (GAC) ............................................50 A.4...GENERAL ISSUE In this study, we compared the adsorptive capacity of bituminous-coal based granular activated carbon (GAC) versus pristine novel

20 CFR 725.101 - Definition and use of terms.

Code of Federal Regulations, 2011 CFR

2011-04-01

... the surface of such land by any person, used in, or to be used in, or resulting from, the work of... means or method, and in the work of preparing the coal so extracted, and includes custom coal..., mixing, storing and loading of bituminous coal, lignite or anthracite, and such other work of preparing...

TRACE ELEMENT PARTITIONING AND TRANSFORMATIONS DURING COMBUSTION OF BITUMINOUS AND SUBBITUMINOUS U.S. COALS IN A 7-KW COMBUSTION SYSTEM. (R827649)

EPA Science Inventory

The perspectives, information and conclusions conveyed in research project abstracts, progress reports, final reports, journal abstracts and journal publications convey the viewpoints of the principal investigator and may not represent the views and policies of ORD and EPA. Concl...

The effect of aggregate type and mix design on the wet skid resistance of bituminous pavement : recommendations for Virginia's Wet Accident Reduction Program.

DOT National Transportation Integrated Search

1995-01-01

This report (1) identified and characterized Virginia's nonpolishing aggregates in terms of their wet skid resistance, (2) compared the standard ASTM E 274-90 skid test to the British Accelerated Polishing Machine (BAPM) and British PendulumTester (B...

75 FR 70950 - Request for Certification of Compliance-Rural Industrialization Loan and Grant Program

Federal Register 2010, 2011, 2012, 2013, 2014

2010-11-19

... buildings, purchase mining equipment, and to create working capital. The office and mine are to be located... enterprise is: 212112 Bituminous Coal Underground Mining. DATES: All interested parties may submit comments... process. Comments should address the two bases for certification and, if possible, provide data to assist...

71. September 1913 "No. 113. Some of the finished bitulithic ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

71. September 1913 "No. 113. Some of the finished bitulithic or bituminous macadam road after being sanded and rolled, in the foreground. In the middle distance men are applying oil to incomplete section. In the far distance, roller is working on foundation course." - Crater Lake National Park Roads, Klamath Falls, Klamath County, OR

20 CFR 410.110 - General definitions and use of terms.

Code of Federal Regulations, 2010 CFR

2010-04-01

... Section 410.110 Employees' Benefits SOCIAL SECURITY ADMINISTRATION FEDERAL COAL MINE HEALTH AND SAFETY ACT... Health and Safety Act of 1969 (Pub. L. 91-173), enacted December 30, 1969, as amended by the Black Lung... be used in, or resulting from, the work of extracting in such area bituminous coal, lignite, or...

Revegetation of surface-mined lands in Pennsylvania

Treesearch

G. Nevin Strock

1980-01-01

The reforestation of surface mines in Pennsylvania became prevalent in the middle 1940's with enactment of state legislation to regulate surface mining of bituminous coal. Though this early legislation did not provide for intensive environment protection standards in comparison to state legislation which followed in the early 1960's and early 1970's and...

Coal desulfurization by chlorinolysis production and combustion test evaluation of product coals

NASA Technical Reports Server (NTRS)

Kalvinskas, J. J.; Daly, D.

1982-01-01

Laboratory-scale screening tests were carried out on coal from Harrison County, Ohio to establish chlorination and hydrodesulfurization conditions for the batch reactor production of chlorinolysis and chlorinolysis-hydrodesulfurized coals. In addition, three bituminous coals, were treated on the lab scale by the chlorinolysis process to provide 39 to 62% desulfurization. Two bituminous coals and one subbituminous coal were then produced in 11 to 15 pound lots as chlorinolysis and hydrodesulfurized coals. The chlorinolysis coals had a desulfurization of 29-69%, reductions in voltatiles and hydrogen. Hydrodesulfurization provided a much greater desulfurization (56-86%), reductions in volatiles and hydrogen. The three coals were combustion tested in the Penn State ""plane flame furnace'' to determine ignition and burning characteristics. All three coals burned well to completion as: raw coals, chlorinolysis processed coals, and hydrodesulfurized coals. The hydrodesulfurized coals experienced greater ignition delays and reduced burning rates than the other coals because of the reduced volatile content. It is thought that the increased open pore volume in the desulfurized-devolatilized coals compensates in part for the decreased volatiles effect on ignition and burning.

Co-combustion of bituminous coal and biomass fuel blends: Thermochemical characterization, potential utilization and environmental advantage.

PubMed

Zhou, Chuncai; Liu, Guijian; Wang, Xudong; Qi, Cuicui

2016-10-01

The thermochemical characteristics and gaseous trace pollutant behaviors during co-combustion medium-to-low ash bituminous coal with typical biomass residues (corn stalk and sawdust) were investigated. Lowering of ignition index, burnout temperature and activation energy in the major combustion stage are observed in the coal/biomass blends. The blending proportion of 20% and 30% are regarded as the optimum blends for corn stalk and sawdust, respectively, in according the limitations of heating value, activation energy, flame stability and base/acid ratio. The reductions of gaseous As, Cd, Cu, Pb, Zn and polycyclic aromatic hydrocarbon (PAHs) were 4.5%, 7.8%, 6.3%, 9.8%, 9.4% and 17.4%, respectively, when co-combustion coal with 20% corn stalk. The elevated capture of trace elements were found in coal/corn stalk blend, while the coal/sawdust blend has the better PAHs control potential. The reduction mechanisms of gaseous trace pollutants were attributed to the fuel property, ash composition and relative residence time during combustion. Copyright © 2016 Elsevier Ltd. All rights reserved.

Comparison of influence of ageing on low-temperature characteristics of asphalt mixtures

NASA Astrophysics Data System (ADS)

Vacková, Pavla; Valentin, Jan; Benešová, Lucie

2017-09-01

Ability of relaxation of asphalt mixtures and thus its resilience to climate change and traffic load is decreasing by influence of aging - in this case aging of bituminous binder. Binder exposed to climate and UV ages and becomes more fragile and susceptible to damage. The results of the research presented in this paper are aimed to finding a correlation between low-temperature properties of referential and aged asphalt mixture specimens and characteristics (not low-temperature) of bituminous binders. In this research there were used conventional road binders, commonly used modified binders and binders additionally modified in the laboratory. The low-temperature characteristics were determined by strength flexural test, commonly used in the Czech Republic for High Modulus Asphalt Mixtures (TP 151), and semi-cylindrical bending test (EN 12697-44). Both of the tests were extended by specimens exposed to artificial long-term aging (EN 12697-52) - storing at 85° C for 5 days. The results were compared with characteristics of binders for finding a suitable correlation between characteristics of binders and asphalt mixtures.

Relation Between Bitumen Content and Percentage Air Voids in Semi Dense Bituminous Concrete

NASA Astrophysics Data System (ADS)

Panda, R. P.; Das, Sudhanshu Sekhar; Sahoo, P. K.

2018-02-01

Hot mix asphalt (HMA) is a heterogeneous mix of aggregate, mineral filler, bitumen, additives and air voids. Researchers have indicated that the durability of the HMA is sensitive on the actual bitumen content and percentage air void. This paper aims at establishing the relationship between the bitumen content and the percentage air voids in Semi Dense Bituminous Concrete (SDBC) using Viscosity Grade-30 (VG-30) bitumen. Total 54 samples have been collected, for formulation and validation of relationship and observed that the percentage air voids increases with decrease in actual bitumen content and vice versa. A minor increase in percentage air voids beyond practice of designed air voids in Marshall Method of design is required for better performance, indicating a need for reducing the codal provision of minimum bitumen content for SDBC as specified in Specification for Road & Bridges (Fourth Revision) published by Indian Road Congress, 2001. The study shows a possibility of reducing designed minimum bitumen content from codal provision for SDBC by 0.2% of weight with VG-30 grade of Bitumen.

Natural gas storage with activated carbon from a bituminous coal

USGS Publications Warehouse

Sun, Jielun; Rood, M.J.; Rostam-Abadi, M.; Lizzio, A.A.

1996-01-01

Granular activated carbons ( -20 + 100 mesh; 0.149-0.84 mm) were produced by physical activation and chemical activation with KOH from an Illinois bituminous coal (IBC-106) for natural gas storage. The products were characterized by BET surface area, micropore volume, bulk density, and methane adsorption capacities. Volumetric methane adsorption capacities (Vm/Vs) of some of the granular carbons produced by physical activation are about 70 cm3/cm3 which is comparable to that of BPL, a commercial activated carbon. Vm/Vs values above 100 cm3/cm3 are obtainable by grinding the granular products to - 325 mesh (<0.044 mm). The increase in Vm/Vs is due to the increase in bulk density of the carbons. Volumetric methane adsorption capacity increases with increasing pore surface area and micropore volume when normalizing with respect to sample bulk volume. Compared with steam-activated carbons, granular carbons produced by KOH activation have higher micropore volume and higher methane adsorption capacities (g/g). Their volumetric methane adsorption capacities are lower due to their lower bulk densities. Copyright ?? 1996 Elsevier Science Ltd.

An Organic Geochemical Assessment of CO2-Coal Interactions During Sequestration

USGS Publications Warehouse

Kolak, Jonathan J.; Burruss, Robert A.

2003-01-01

Three well-characterized coal samples of varying rank were extracted with supercritical CO2 to determine the amount of polycyclic aromatic hydrocarbons (PAHs) that could be mobilized during simulated CO2 injection/sequestration in deep coal beds. The supercritical CO2 extractions were conducted at 40?C and 100 bars, roughly corresponding to a depth of 1 km. The greatest amount of PAHs was extracted from the high-volatile C bituminous coal sample. Extracts from the subbituminous C and anthracite coal samples contained lower concentrations of these compounds. The effectiveness of supercritical CO2 in liberating PAHs from the coal sample was evaluated in a comparison with a parallel series of Soxhlet extractions using 100% dichloromethane. More PAHs were extracted from the lower rank coal samples with dichloromethane than with supercritical CO2. The results from this investigation indicate that, regardless of coal rank, CO2 injection into deep coal beds may mobilize PAHs from the coal matrix. However, more PAHs could be mobilized during CO2 sequestration in a high-volatile C bituminous coal bed than in either of the other two coal ranks studied.

Relation Between Bitumen Content and Percentage Air Voids in Semi Dense Bituminous Concrete

NASA Astrophysics Data System (ADS)

Panda, R. P.; Das, Sudhanshu Sekhar; Sahoo, P. K.

2018-06-01

Hot mix asphalt (HMA) is a heterogeneous mix of aggregate, mineral filler, bitumen, additives and air voids. Researchers have indicated that the durability of the HMA is sensitive on the actual bitumen content and percentage air void. This paper aims at establishing the relationship between the bitumen content and the percentage air voids in Semi Dense Bituminous Concrete (SDBC) using Viscosity Grade-30 (VG-30) bitumen. Total 54 samples have been collected, for formulation and validation of relationship and observed that the percentage air voids increases with decrease in actual bitumen content and vice versa. A minor increase in percentage air voids beyond practice of designed air voids in Marshall Method of design is required for better performance, indicating a need for reducing the codal provision of minimum bitumen content for SDBC as specified in Specification for Road & Bridges (Fourth Revision) published by Indian Road Congress, 2001. The study shows a possibility of reducing designed minimum bitumen content from codal provision for SDBC by 0.2% of weight with VG-30 grade of Bitumen.

Emission characteristics for polycyclic aromatic hydrocarbons from solid fuels burned in domestic stoves in rural China

PubMed Central

SHEN, Guofeng; TAO, Shu; Chen, Yuanchen; Zhang, Yanyan; Wei, Siye; Xue, Miao; Wang, Bin; WANG, Rong; LV, Yan; LI, Wei; SHEN, Huizhong; HUANG, Ye; CHEN, Han

2014-01-01

Emission characterization of polycyclic aromatic hydrocarbons (PAHs) from residential combustion of crop residues, woody material, coal, and biomass pellets in domestic stoves in rural China are compared in term of emission factors (EFs), influencing factors, composition profiles, isomer ratios and phase distributions. The EFs of PAHs vary by two orders of magnitude among fuel types suggesting that a detailed fuel categorization is useful in the development of an emission inventory and potential in emission abatement of PAHs by replacing dirty fuels with relatively cleaner ones. The influence of fuel moisture in biomass burning is non-linear. Biofuels with very low moisture display relatively high emissions as do fuels with very high moisture. Bituminous coals and brushwood yield relatively large fractions of high molecular PAHs. The emission factor of Benzo(a)pyrene equivalent quantity for raw bituminous coal is as high as 52 mg/kg, which is 1–2 orders of magnitude higher than the other fuels. For source diagnosis, high molecular weight isomers are more informative than low molecular weight ones and multiple ratios could be used together whenever possible. PMID:24245776

Nitrogen conversion under rapid pyrolysis of two types of aquatic biomass and corresponding blends with coal.

PubMed

Yuan, Shuai; Chen, Xue-li; Li, Wei-feng; Liu, Hai-feng; Wang, Fu-chen

2011-11-01

Rapid pyrolysis of two types of aquatic biomass (blue-green algae and water hyacinth), and their blends with two coals (bituminous and anthracite) was carried out in a high-frequency furnace. Nitrogen conversions during rapid pyrolysis of the two biomass and the interactions between the biomass and coals on nitrogen conversions were investigated. Results show that little nitrogen retained in char after the biomass pyrolysis, and NH(3) yields were higher than HCN. During co-pyrolysis of biomass and coal, interactions between biomass and coal decreased char-N yields and increased volatile-N yields, but the total yields of NH(3)+HCN in volatile-N were decreased in which HCN formations were decreased consistently, while NH(3) formations were only decreased in the high-temperature range but promoted in the low-temperature range. Interactions between blue-green algae and coals are stronger than those between water hyacinth and coal, and interactions between biomass and bituminous are stronger than those between biomass and anthracite. Copyright © 2011 Elsevier Ltd. All rights reserved.

Thermogravimetric analysis of the behavior of sub-bituminous coal and cellulosic ethanol residue during co-combustion.

PubMed

Buratti, C; Barbanera, M; Bartocci, P; Fantozzi, F

2015-06-01

The influence of the addition of cellulosic ethanol residue (CER) on the combustion of Indonesian sub-bituminous coal was analyzed by non isothermal thermo-gravimetric analysis (TGA). The effect of blends ratio (5%, 10%, 15% and 20%), interaction mechanism, and heating rate (5°C/min, 10°C/min, 15°C/min, 20°C/min) on the combustion process was studied. The results show that the increase of the blending ratio allows to achieve the increase of the combustibility index from 7.49E-08 to 5.26E-07 at the blending ratio of 20%. Two types of non-isothermal kinetic analysis methods (Ozawa-Flynn-Wall and Vyazovkin) were also applied. Results indicate that the activation energy of the blends decreases with increasing the conversion rate. In particular, the blending ratio of 20% confirms to have the better combustion performance, with the average value of the activation energy equal to 41.10 kJ/mol obtained by Ozawa-Flynn-Wall model and 31.17 kJ/mol obtained by Vyazovkin model. Copyright © 2015 Elsevier Ltd. All rights reserved.

Physico-chemical properties and gasification reactivity of co-pyrolysis char from different rank of coal blended with lignocellulosic biomass: Effects of the cellulose.

PubMed

Wu, Zhiqiang; Wang, Shuzhong; Luo, Zhengyuan; Chen, Lin; Meng, Haiyu; Zhao, Jun

2017-07-01

In this paper, the influence of cellulose on the physicochemical properties and the gasification reactivity of co-pyrolysis char was investigated. A specific surface area analyzer and an X-ray diffraction system were used to characterize the pore structure and the micro-crystalline structure of char. Fractal theory and deconvolution method were applied to quantitatively investigate the influence of cellulose on the structure of co-pyrolysis char. The results indicate that the improvements in the pore structure due to the presence of cellulose are more pronounced in the case of anthracite char with respect to bituminous char. Cellulose promotes the ordering of micro-scale structure and the uniformity of both anthracite and bituminous char, while the negative synergetic effect was observed during gasification of co-pyrolysis char. The exponential relationships between fractal dimension and specific surface area were determined, along with the relations between the gasification reactivity index and the microcrystalline structure parameter. Copyright © 2017 Elsevier Ltd. All rights reserved.

Rapid co-pyrolysis of rice straw and a bituminous coal in a high-frequency furnace and gasification of the residual char.

PubMed

Yuan, Shuai; Dai, Zheng-hua; Zhou, Zhi-jie; Chen, Xue-li; Yu, Guang-suo; Wang, Fu-chen

2012-04-01

Rapid pyrolysis of rice straw (RS) and Shenfu bituminous coal (SB) separately, and rapid co-pyrolysis of RS/SB blends (mass ratio 1:4, 1:4, and 4:1), were carried out in a high-frequency furnace which can ensure both high heating rate and satisfying contact of fuel particles. Synergies between RS and SB during rapid co-pyrolysis were investigated. Intrinsic and morphological structures of residual char from co-pyrolysis, and their effects on gasification characteristics were also studied. Synergies occurred during rapid co-pyrolysis of RS and SB (RS/SB=1:4) resulting in decreasing char yields and increasing volatile yields. Synergies also happened during gasification of the char derived from co-pyrolysis of RS and SB with mass ratio of 1:4. The increased mass ratio of RS to SB did not only weaken synergies during co-pyrolysis, but significantly reduced the gasification rates of the co-pyrolysis char compared to the calculated values. Results can help to optimize co-conversion process of biomass/coal. Copyright © 2012 Elsevier Ltd. All rights reserved.

48 CFR 1315.407 - Special cost or pricing areas.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 48 Federal Acquisition Regulations System 5 2010-10-01 2010-10-01 false Special cost or pricing... CONTRACTING METHODS AND CONTRACT TYPES CONTRACTING BY NEGOTIATION Contract Pricing 1315.407 Special cost or pricing areas. ...

48 CFR 15.407 - Special cost or pricing areas.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 48 Federal Acquisition Regulations System 1 2010-10-01 2010-10-01 false Special cost or pricing... CONTRACTING METHODS AND CONTRACT TYPES CONTRACTING BY NEGOTIATION Contract Pricing 15.407 Special cost or pricing areas. ...

46 CFR 153.1002 - Special operating requirements for heat sensitive cargoes.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 5 2011-10-01 2011-10-01 false Special operating requirements for heat sensitive cargoes. 153.1002 Section 153.1002 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED... MATERIALS Operations Special Cargo Procedures § 153.1002 Special operating requirements for heat sensitive...

46 CFR 153.1002 - Special operating requirements for heat sensitive cargoes.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 5 2010-10-01 2010-10-01 false Special operating requirements for heat sensitive cargoes. 153.1002 Section 153.1002 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED... MATERIALS Operations Special Cargo Procedures § 153.1002 Special operating requirements for heat sensitive...

24 CFR 1003.203 - Special economic development activities.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 24 Housing and Urban Development 4 2010-04-01 2010-04-01 false Special economic development... Eligible Activities § 1003.203 Special economic development activities. A grantee may use ICDBG funds for special economic development activities in addition to other activities authorized in this subpart which...

7 CFR 762.128 - Environmental and special laws.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 7 Agriculture 7 2014-01-01 2014-01-01 false Environmental and special laws. 762.128 Section 762.128 Agriculture Regulations of the Department of Agriculture (Continued) FARM SERVICE AGENCY, DEPARTMENT OF AGRICULTURE SPECIAL PROGRAMS GUARANTEED FARM LOANS § 762.128 Environmental and special laws. (a...

24 CFR 570.203 - Special economic development activities.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 24 Housing and Urban Development 3 2010-04-01 2010-04-01 false Special economic development... § 570.203 Special economic development activities. A recipient may use CDBG funds for special economic... part of an economic development project. Guidelines for selecting activities to assist under this...

40 CFR 1060.640 - What special provisions apply to branded equipment?

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 32 2010-07-01 2010-07-01 false What special provisions apply to branded equipment? 1060.640 Section 1060.640 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... STATIONARY EQUIPMENT Special Compliance Provisions § 1060.640 What special provisions apply to branded...

46 CFR 153.1002 - Special operating requirements for heat sensitive cargoes.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 5 2014-10-01 2014-10-01 false Special operating requirements for heat sensitive cargoes. 153.1002 Section 153.1002 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED... MATERIALS Operations Special Cargo Procedures § 153.1002 Special operating requirements for heat sensitive...

46 CFR 153.1002 - Special operating requirements for heat sensitive cargoes.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 5 2013-10-01 2013-10-01 false Special operating requirements for heat sensitive cargoes. 153.1002 Section 153.1002 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED... MATERIALS Operations Special Cargo Procedures § 153.1002 Special operating requirements for heat sensitive...

46 CFR 153.1002 - Special operating requirements for heat sensitive cargoes.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 5 2012-10-01 2012-10-01 false Special operating requirements for heat sensitive cargoes. 153.1002 Section 153.1002 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED... MATERIALS Operations Special Cargo Procedures § 153.1002 Special operating requirements for heat sensitive...

10 CFR 420.38 - Special projects expenditure prohibitions and limitations.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 10 Energy 3 2010-01-01 2010-01-01 false Special projects expenditure prohibitions and limitations. 420.38 Section 420.38 Energy DEPARTMENT OF ENERGY ENERGY CONSERVATION STATE ENERGY PROGRAM Implementation of Special Projects Financial Assistance § 420.38 Special projects expenditure prohibitions and...

10 CFR 420.38 - Special projects expenditure prohibitions and limitations.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 10 Energy 3 2011-01-01 2011-01-01 false Special projects expenditure prohibitions and limitations. 420.38 Section 420.38 Energy DEPARTMENT OF ENERGY ENERGY CONSERVATION STATE ENERGY PROGRAM Implementation of Special Projects Financial Assistance § 420.38 Special projects expenditure prohibitions and...

10 CFR 420.38 - Special projects expenditure prohibitions and limitations.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 10 Energy 3 2012-01-01 2012-01-01 false Special projects expenditure prohibitions and limitations. 420.38 Section 420.38 Energy DEPARTMENT OF ENERGY ENERGY CONSERVATION STATE ENERGY PROGRAM Implementation of Special Projects Financial Assistance § 420.38 Special projects expenditure prohibitions and...

10 CFR 420.38 - Special projects expenditure prohibitions and limitations.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 10 Energy 3 2013-01-01 2013-01-01 false Special projects expenditure prohibitions and limitations. 420.38 Section 420.38 Energy DEPARTMENT OF ENERGY ENERGY CONSERVATION STATE ENERGY PROGRAM Implementation of Special Projects Financial Assistance § 420.38 Special projects expenditure prohibitions and...

10 CFR 420.38 - Special projects expenditure prohibitions and limitations.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 10 Energy 3 2014-01-01 2014-01-01 false Special projects expenditure prohibitions and limitations. 420.38 Section 420.38 Energy DEPARTMENT OF ENERGY ENERGY CONSERVATION STATE ENERGY PROGRAM Implementation of Special Projects Financial Assistance § 420.38 Special projects expenditure prohibitions and...

49 CFR 1244.7 - Special studies.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 9 2010-10-01 2010-10-01 false Special studies. 1244.7 Section 1244.7... PROPERTY-RAILROADS § 1244.7 Special studies. (a) Although routine submission of hard copy waybills is... hard copies of the underlying waybills for special studies. (b) The Board may order the subject...

49 CFR 1244.7 - Special studies.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 49 Transportation 9 2011-10-01 2011-10-01 false Special studies. 1244.7 Section 1244.7... PROPERTY-RAILROADS § 1244.7 Special studies. (a) Although routine submission of hard copy waybills is... hard copies of the underlying waybills for special studies. (b) The Board may order the subject...

24 CFR 1003.203 - Special economic development activities.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 24 Housing and Urban Development 4 2013-04-01 2013-04-01 false Special economic development... Eligible Activities § 1003.203 Special economic development activities. A grantee may use ICDBG funds for special economic development activities in addition to other activities authorized in this subpart which...

24 CFR 1003.203 - Special economic development activities.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 24 Housing and Urban Development 4 2014-04-01 2014-04-01 false Special economic development... Eligible Activities § 1003.203 Special economic development activities. A grantee may use ICDBG funds for special economic development activities in addition to other activities authorized in this subpart which...

24 CFR 1003.203 - Special economic development activities.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 24 Housing and Urban Development 4 2012-04-01 2012-04-01 false Special economic development... Eligible Activities § 1003.203 Special economic development activities. A grantee may use ICDBG funds for special economic development activities in addition to other activities authorized in this subpart which...

24 CFR 570.203 - Special economic development activities.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 24 Housing and Urban Development 3 2013-04-01 2013-04-01 false Special economic development... § 570.203 Special economic development activities. A recipient may use CDBG funds for special economic... part of an economic development project. Guidelines for selecting activities to assist under this...

24 CFR 570.203 - Special economic development activities.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 24 Housing and Urban Development 3 2012-04-01 2012-04-01 false Special economic development... § 570.203 Special economic development activities. A recipient may use CDBG funds for special economic... part of an economic development project. Guidelines for selecting activities to assist under this...

24 CFR 1003.203 - Special economic development activities.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 24 Housing and Urban Development 4 2011-04-01 2011-04-01 false Special economic development... Eligible Activities § 1003.203 Special economic development activities. A grantee may use ICDBG funds for special economic development activities in addition to other activities authorized in this subpart which...

20 CFR 404.261 - Computing your special minimum primary insurance amount.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 20 Employees' Benefits 2 2010-04-01 2010-04-01 false Computing your special minimum primary..., SURVIVORS AND DISABILITY INSURANCE (1950- ) Computing Primary Insurance Amounts Special Minimum Primary Insurance Amounts § 404.261 Computing your special minimum primary insurance amount. (a) Years of coverage...

40 CFR 18.10 - Appointment of Special Research Consultants for Environmental Protection.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 1 2011-07-01 2011-07-01 false Appointment of Special Research... PROTECTION AGENCY GENERAL ENVIRONMENTAL PROTECTION RESEARCH FELLOWSHIPS AND SPECIAL RESEARCH CONSULTANTS FOR ENVIRONMENTAL PROTECTION § 18.10 Appointment of Special Research Consultants for Environmental Protection. (a...

19 CFR 200.735-122 - Special Government employees.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 19 Customs Duties 3 2012-04-01 2012-04-01 false Special Government employees. 200.735-122 Section... Government employees. (a) Except as provided in paragraph (b) of this section, each special Government... employment; and (2) The financial interests of the special Government employee which the Commission...

19 CFR 200.735-122 - Special Government employees.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 19 Customs Duties 3 2010-04-01 2010-04-01 false Special Government employees. 200.735-122 Section... Government employees. (a) Except as provided in paragraph (b) of this section, each special Government... employment; and (2) The financial interests of the special Government employee which the Commission...

42 CFR 412.96 - Special treatment: Referral centers.

Code of Federal Regulations, 2010 CFR

2010-10-01

... MEDICARE PROGRAM PROSPECTIVE PAYMENT SYSTEMS FOR INPATIENT HOSPITAL SERVICES Special Treatment of Certain Facilities Under the Prospective Payment System for Inpatient Operating Costs § 412.96 Special treatment... 42 Public Health 2 2010-10-01 2010-10-01 false Special treatment: Referral centers. 412.96 Section...

5 CFR 532.303 - Specialized industry.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 5 Administrative Personnel 1 2012-01-01 2012-01-01 false Specialized industry. 532.303 Section 532... SYSTEMS Determining Rates for Principal Types of Positions § 532.303 Specialized industry. (a)(1) Under the appropriated fund wage system, a “specialized industry” is a Federal activity engaged in the...

5 CFR 532.303 - Specialized industry.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 5 Administrative Personnel 1 2011-01-01 2011-01-01 false Specialized industry. 532.303 Section 532... SYSTEMS Determining Rates for Principal Types of Positions § 532.303 Specialized industry. (a)(1) Under the appropriated fund wage system, a “specialized industry” is a Federal activity engaged in the...

5 CFR 532.303 - Specialized industry.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 5 Administrative Personnel 1 2013-01-01 2013-01-01 false Specialized industry. 532.303 Section 532... SYSTEMS Determining Rates for Principal Types of Positions § 532.303 Specialized industry. (a)(1) Under the appropriated fund wage system, a “specialized industry” is a Federal activity engaged in the...

5 CFR 532.303 - Specialized industry.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 5 Administrative Personnel 1 2014-01-01 2014-01-01 false Specialized industry. 532.303 Section 532... SYSTEMS Determining Rates for Principal Types of Positions § 532.303 Specialized industry. (a)(1) Under the appropriated fund wage system, a “specialized industry” is a Federal activity engaged in the...

7 CFR 632.18 - Special projects.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 6 2010-01-01 2010-01-01 false Special projects. 632.18 Section 632.18 Agriculture... AGRICULTURE LONG TERM CONTRACTING RURAL ABANDONED MINE PROGRAM Qualifications § 632.18 Special projects. (a) The NRCS State conservationist may approve the following types of special projects subject to the...

36 CFR 12.4 - Special events and demonstrations.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 36 Parks, Forests, and Public Property 1 2011-07-01 2011-07-01 false Special events and... INTERIOR NATIONAL CEMETERY REGULATIONS § 12.4 Special events and demonstrations. Conducting a special event... events conducted for Memorial Day, Veterans Day and other dates designated by the superintendent as...

36 CFR 12.4 - Special events and demonstrations.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 36 Parks, Forests, and Public Property 1 2013-07-01 2013-07-01 false Special events and... INTERIOR NATIONAL CEMETERY REGULATIONS § 12.4 Special events and demonstrations. Conducting a special event... events conducted for Memorial Day, Veterans Day and other dates designated by the superintendent as...

36 CFR 12.4 - Special events and demonstrations.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 36 Parks, Forests, and Public Property 1 2014-07-01 2014-07-01 false Special events and... INTERIOR NATIONAL CEMETERY REGULATIONS § 12.4 Special events and demonstrations. Conducting a special event... events conducted for Memorial Day, Veterans Day and other dates designated by the superintendent as...

36 CFR 12.4 - Special events and demonstrations.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 36 Parks, Forests, and Public Property 1 2012-07-01 2012-07-01 false Special events and... INTERIOR NATIONAL CEMETERY REGULATIONS § 12.4 Special events and demonstrations. Conducting a special event... events conducted for Memorial Day, Veterans Day and other dates designated by the superintendent as...

36 CFR 12.4 - Special events and demonstrations.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 36 Parks, Forests, and Public Property 1 2010-07-01 2010-07-01 false Special events and... INTERIOR NATIONAL CEMETERY REGULATIONS § 12.4 Special events and demonstrations. Conducting a special event... events conducted for Memorial Day, Veterans Day and other dates designated by the superintendent as...

48 CFR 970.1504-1-8 - Special equipment purchases.

Code of Federal Regulations, 2010 CFR

2010-10-01

... boilers, generators, machine tools, and large electrical equipment. In some cases, it would also include... 48 Federal Acquisition Regulations System 5 2010-10-01 2010-10-01 false Special equipment....1504-1-8 Special equipment purchases. (a) Special equipment is sometimes procured in conjunction with...

7 CFR 632.18 - Special projects.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 7 Agriculture 6 2013-01-01 2013-01-01 false Special projects. 632.18 Section 632.18 Agriculture... AGRICULTURE LONG TERM CONTRACTING RURAL ABANDONED MINE PROGRAM Qualifications § 632.18 Special projects. (a) The NRCS State conservationist may approve the following types of special projects subject to the...

7 CFR 632.18 - Special projects.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 7 Agriculture 6 2014-01-01 2014-01-01 false Special projects. 632.18 Section 632.18 Agriculture... AGRICULTURE LONG TERM CONTRACTING RURAL ABANDONED MINE PROGRAM Qualifications § 632.18 Special projects. (a) The NRCS State conservationist may approve the following types of special projects subject to the...

7 CFR 632.18 - Special projects.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 6 2011-01-01 2011-01-01 false Special projects. 632.18 Section 632.18 Agriculture... AGRICULTURE LONG TERM CONTRACTING RURAL ABANDONED MINE PROGRAM Qualifications § 632.18 Special projects. (a) The NRCS State conservationist may approve the following types of special projects subject to the...

13 CFR 120.393 - Are there special application requirements?

Code of Federal Regulations, 2011 CFR

2011-01-01

... 13 Business Credit and Assistance 1 2011-01-01 2011-01-01 false Are there special application requirements? 120.393 Section 120.393 Business Credit and Assistance SMALL BUSINESS ADMINISTRATION BUSINESS LOANS Special Purpose Loans Builders Loan Program § 120.393 Are there special application requirements...

13 CFR 120.393 - Are there special application requirements?

Code of Federal Regulations, 2013 CFR

2013-01-01

... 13 Business Credit and Assistance 1 2013-01-01 2013-01-01 false Are there special application requirements? 120.393 Section 120.393 Business Credit and Assistance SMALL BUSINESS ADMINISTRATION BUSINESS LOANS Special Purpose Loans Builders Loan Program § 120.393 Are there special application requirements...

13 CFR 120.393 - Are there special application requirements?

Code of Federal Regulations, 2012 CFR

2012-01-01

... 13 Business Credit and Assistance 1 2012-01-01 2012-01-01 false Are there special application requirements? 120.393 Section 120.393 Business Credit and Assistance SMALL BUSINESS ADMINISTRATION BUSINESS LOANS Special Purpose Loans Builders Loan Program § 120.393 Are there special application requirements...

13 CFR 120.393 - Are there special application requirements?

Code of Federal Regulations, 2014 CFR

2014-01-01

... 13 Business Credit and Assistance 1 2014-01-01 2014-01-01 false Are there special application requirements? 120.393 Section 120.393 Business Credit and Assistance SMALL BUSINESS ADMINISTRATION BUSINESS LOANS Special Purpose Loans Builders Loan Program § 120.393 Are there special application requirements...

13 CFR 120.393 - Are there special application requirements?

Code of Federal Regulations, 2010 CFR

2010-01-01

... 13 Business Credit and Assistance 1 2010-01-01 2010-01-01 false Are there special application requirements? 120.393 Section 120.393 Business Credit and Assistance SMALL BUSINESS ADMINISTRATION BUSINESS LOANS Special Purpose Loans Builders Loan Program § 120.393 Are there special application requirements...

31 CFR Appendix A to Chapter V - Alphabetical Listing of Blocked Persons, Blocked Vessels, Specially Designated Nationals...

Code of Federal Regulations, 2010 CFR

2010-07-01

... 31 Money and Finance: Treasury 3 2010-07-01 2010-07-01 false Alphabetical Listing of Blocked Persons, Blocked Vessels, Specially Designated Nationals, Specially Designated Terrorists, Specially Designated Global Terrorists, Foreign Terrorist Organizations, and Specially Designated Narcotics Traffickers (as of May 13, 2010) A Appendix A to Chapte...

Intrinsic and extrinsic defects in a family of coal-derived graphene quantum dots

DOE Office of Scientific and Technical Information (OSTI.GOV)

Singamaneni, Srinivasa Rao, E-mail: ssingam@ncsu.edu, E-mail: tour@rice.edu; Department of Material Science and Engineering, North Carolina State University, Raleigh, North Carolina 27695; Tol, Johan van

In this letter, we report on the high frequency (239.2 and 336 GHz) electron spin resonance (ESR) studies performed on graphene quantum dots (GQDs), prepared through a wet chemistry route from three types of coal: (a) bituminous, (b) anthracite, and (c) coke; and from non-coal derived GQDs. The microwave frequency-, power-, and temperature-dependent ESR spectra coupled with computer-aided simulations reveal four distinct magnetic defect centers. In bituminous- and anthracite-derived GQDs, we have identified two of them as intrinsic carbon-centered magnetic defect centers (a broad signal of peak to peak width = 697 (10{sup −4} T), g = 2.0023; and a narrow signal of peak tomore » peak width = 60 (10{sup −4} T), g = 2.003). The third defect center is Mn{sup 2+} ({sup 6}S{sub 5/2}, 3d{sup 5}) (signal width = 61 (10{sup −4} T), g = 2.0023, A{sub iso} = 93(10{sup −4} T)), and the fourth defect is identified as Cu{sup 2+} ({sup 2}D{sub 5/2}, 3d{sup 9}) (g{sub ⊥} = 2.048 and g{sub ‖} = 2.279), previously undetected. Coke-derived and non-coal derived GQDs show Mn{sup 2+} and two-carbon related signals, and no Cu{sup 2+} signal. The extrinsic impurities most likely originate from the starting coal. Furthermore, Raman, photoluminescence, and ESR measurements detected no noticeable changes in the properties of the bituminous GQDs after one year. This study highlights the importance of employing high frequency ESR spectroscopy in identifying the (magnetic) defects, which are roadblocks for spin relaxation times of graphene-based materials. These defects would not have been possible to probe by other spin transport measurements.« less

Mercury in coal and the impact of coal quality on mercury emissions from combustion systems

USGS Publications Warehouse

Kolker, A.; Senior, C.L.; Quick, J.C.

2006-01-01

The proportion of Hg in coal feedstock that is emitted by stack gases of utility power stations is a complex function of coal chemistry and properties, combustion conditions, and the positioning and type of air pollution control devices employed. Mercury in bituminous coal is found primarily within Fe-sulfides, whereas lower rank coal tends to have a greater proportion of organic-bound Hg. Preparation of bituminous coal to reduce S generally reduces input Hg relative to in-ground concentrations, but the amount of this reduction varies according to the fraction of Hg in sulfides and the efficiency of sulfide removal. The mode of occurrence of Hg in coal does not directly affect the speciation of Hg in the combustion flue gas. However, other constituents in the coal, notably Cl and S, and the combustion characteristics of the coal, influence the species of Hg that are formed in the flue gas and enter air pollution control devices. The formation of gaseous oxidized Hg or particulate-bound Hg occurs post-combustion; these forms of Hg can be in part captured in the air pollution control devices that exist on coal-fired boilers, without modification. For a given coal type, the capture efficiency of Hg by pollution control systems varies according to type of device and the conditions of its deployment. For bituminous coal, on average, more than 60% of Hg in flue gas is captured by fabric filter (FF) and flue-gas desulfurization (FGD) systems. Key variables affecting performance for Hg control include Cl and S content of the coal, the positioning (hot side vs. cold side) of the system, and the amount of unburned C in coal ash. Knowledge of coal quality parameters and their effect on the performance of air pollution control devices allows optimization of Hg capture co-benefit. ?? 2006 Elsevier Ltd. All rights reserved.

Estimation of the tangible costs of black lung disease related disability to the bituminous coal mine operators of Appalachia

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cameron, R.B.

1976-06-15

The early work on estimating the contribution of black lung disability to the costs of coal production consisted of an extensive survey of the medical literature: To determine what black lung disease is and how it may be related to the process of mining coal; and to determine the nature of any disability which may result. The disease itself is not well defined, there being a multiplicity of disorders associated with what is loosely called black lung disease. It was evident, however, that there is excessive lung-disease-related disability among underground bituminous coal miners. The data tape of the Appalachian Laboratorymore » for Occupational Respiratory Disease (ALFORD) 1969 to 1971 coal workers' pneumoconiosis prevalence study includes substantial medical information on some 10,000 miners and served as the sample for the disability cost estimates. Because of incompleteness of data clinical criteria could not be used to determine the presence of disability. The ALFORD tape, however, includes information by which miners could be categorized subjectively according to complaints of shortness of breath, dyspnea, which was chosen as the indicator of disability. The decision to use dyspnea as a criterion for disability is supported by: First, shortness of breath, to a large extent, is responsible for the inability of diseased miners to work at the rate of their healthy peers; and, secondly, the ALFORD dyspnea data are consistent with the Public Health Service 1963 study. The cost estimates include: (1) Estimate of the increase in output which might be expected to occur with the elimination of black lung disability; or (2) estimate of a discounted income stream lost because of the disability. Each of these estimates yield a range of costs from one to five percent of the annual total product revenue of the bituminous coal industry.« less

Chemistry and origin of minor and trace elements in vitrinite concentrates from a rank series from the eastern United States, England, and Australia

USGS Publications Warehouse

Lyons, P.C.; Palmer, C.A.; Bostick, N.H.; Fletcher, J.D.; Dulong, F.T.; Brown, F.W.; Brown, Z.A.; Krasnow, M.R.; Romankiw, L.A.

1989-01-01

A rank series consisting of twelve vitrinite concentrates and companion whole-coal samples from mined coal beds in the eastern United States, England, and Australia were analyzed for C, H, N, O, ash, and 47 trace and minor elements by standard elemental, instrumental neutron activation analysis (INAA), and direct-current-arc spectrographic (DCAS) techniques. The reflectance of vitrinite, atomic H:C and O:C, and ash-free carbon data were used to determine ranks that range from high-volatile C bituminous coal to meta-anthracite. A van Krevelen (atomic H:C vs. O:C) diagram of the vitrinite concentrates shows a smooth curve having its lowest point at H:C = 0.18 and O:C = 0.01. This improves the van Krevelen diagram by the addition of our vitrinite concentrate from meta-anthracite from the Narragansett basin of New England. Boron content (400-450 ppm) in two Illinois basin vitrinite concentrates was about an order of magnitude higher than B contents in other concentrates analyzed. We attribute this to marine origin or hydrothermal activity. The alkaline-earth elements Ca, Mg and Ba (DCAS) have higher concentrations in our vitrinite concentrates from bituminous coals of the Appalachian basin, than they do in vitrinite concentrates from the marine-roofed bituminous coals of the Illinois basin; therefore, a nonmarine origin for these alkaline-earth elements is postulated for the Appalachian basin coals. An ion-exchange mechanism due to high concentrations of these elements as ions in diagenetic water, but probably not recent ground water, may be responsible for the relatively high values of these elements in Appalachian concentrates. Higher concentrations of Ni and Cr in one of the English vitrinite concentrates and of Zr in the Australian concentrate probably indicate organic association and detrital influence, respectively. ?? 1989.

Mercury emissions during cofiring of sub-bituminous coal and biomass (chicken waste, wood, coffee residue, and tobacco stalk) in a laboratory-scale fluidized bed combustor

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yan Cao; Hongcang Zhou; Junjie Fan

Four types of biomass (chicken waste, wood pellets, coffee residue, and tobacco stalks) were cofired at 30 wt % with a U.S. sub-bituminous coal (Powder River Basin Coal) in a laboratory-scale fluidized bed combustor. A cyclone, followed by a quartz filter, was used for fly ash removal during tests. The temperatures of the cyclone and filter were controlled at 250 and 150{sup o}C, respectively. Mercury speciation and emissions during cofiring were investigated using a semicontinuous mercury monitor, which was certified using ASTM standard Ontario Hydra Method. Test results indicated mercury emissions were strongly correlative to the gaseous chlorine concentrations, butmore » not necessarily correlative to the chlorine contents in cofiring fuels. Mercury emissions could be reduced by 35% during firing of sub-bituminous coal using only a quartz filter. Cofiring high-chlorine fuel, such as chicken waste (Cl = 22340 wppm), could largely reduce mercury emissions by over 80%. When low-chlorine biomass, such as wood pellets (Cl = 132 wppm) and coffee residue (Cl = 134 wppm), is cofired, mercury emissions could only be reduced by about 50%. Cofiring tobacco stalks with higher chlorine content (Cl = 4237 wppm) did not significantly reduce mercury emissions. Gaseous speciated mercury in flue gas after a quartz filter indicated the occurrence of about 50% of total gaseous mercury to be the elemental mercury for cofiring chicken waste, but occurrence of above 90% of the elemental mercury for all other cases. Both the higher content of alkali metal oxides or alkali earth metal oxides in tested biomass and the occurrence of temperatures lower than 650{sup o}C in the upper part of the fluidized bed combustor seemed to be responsible for the reduction of gaseous chlorine and, consequently, limited mercury emissions reduction during cofiring. 36 refs., 3 figs. 1 tab.« less

7 CFR 621.44 - Special studies.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 6 2011-01-01 2011-01-01 false Special studies. 621.44 Section 621.44 Agriculture... studies. As designated, NRCS represents USDA on special study groups such as for the Colorado River Basin Salinity Control Program Studies. ...

7 CFR 621.44 - Special studies.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 6 2010-01-01 2010-01-01 false Special studies. 621.44 Section 621.44 Agriculture... studies. As designated, NRCS represents USDA on special study groups such as for the Colorado River Basin Salinity Control Program Studies. ...

50 CFR 17.86 - Special rules-plants. [Reserved

Code of Federal Regulations, 2014 CFR

2014-10-01

... 50 Wildlife and Fisheries 2 2014-10-01 2014-10-01 false Special rules-plants. [Reserved] 17.86... WILDLIFE AND PLANTS (CONTINUED) ENDANGERED AND THREATENED WILDLIFE AND PLANTS Experimental Populations § 17.86 Special rules—plants. [Reserved] ...

50 CFR 17.86 - Special rules-plants. [Reserved

Code of Federal Regulations, 2011 CFR

2011-10-01

... 50 Wildlife and Fisheries 2 2011-10-01 2011-10-01 false Special rules-plants. [Reserved] 17.86... WILDLIFE AND PLANTS (CONTINUED) ENDANGERED AND THREATENED WILDLIFE AND PLANTS Experimental Populations § 17.86 Special rules—plants. [Reserved] ...

50 CFR 17.86 - Special rules-plants. [Reserved

Code of Federal Regulations, 2010 CFR

2010-10-01

... 50 Wildlife and Fisheries 2 2010-10-01 2010-10-01 false Special rules-plants. [Reserved] 17.86... WILDLIFE AND PLANTS (CONTINUED) ENDANGERED AND THREATENED WILDLIFE AND PLANTS Experimental Populations § 17.86 Special rules—plants. [Reserved] ...

31 CFR 128.13 - Special survey reports.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 31 Money and Finance: Treasury 1 2014-07-01 2014-07-01 false Special survey reports. 128.13... Reports on International Capital Transactions and Positions § 128.13 Special survey reports. The Secretary may prescribe special survey reports at such times as the Secretary determines there is a need for...

31 CFR 128.13 - Special survey reports.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 31 Money and Finance: Treasury 1 2012-07-01 2012-07-01 false Special survey reports. 128.13... Reports on International Capital Transactions and Positions § 128.13 Special survey reports. The Secretary may prescribe special survey reports at such times as the Secretary determines there is a need for...

31 CFR 128.23 - Special survey reports.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 31 Money and Finance: Treasury 1 2012-07-01 2012-07-01 false Special survey reports. 128.23... Reports on Foreign Currency Positions § 128.23 Special survey reports. The Secretary may prescribe special survey reports with respect to foreign exchange positions and related information at such times as the...

31 CFR 128.23 - Special survey reports.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 31 Money and Finance: Treasury 1 2011-07-01 2011-07-01 false Special survey reports. 128.23... Reports on Foreign Currency Positions § 128.23 Special survey reports. The Secretary may prescribe special survey reports with respect to foreign exchange positions and related information at such times as the...

31 CFR 128.23 - Special survey reports.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 31 Money and Finance: Treasury 1 2013-07-01 2013-07-01 false Special survey reports. 128.23... Reports on Foreign Currency Positions § 128.23 Special survey reports. The Secretary may prescribe special survey reports with respect to foreign exchange positions and related information at such times as the...

31 CFR 128.13 - Special survey reports.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 31 Money and Finance: Treasury 1 2013-07-01 2013-07-01 false Special survey reports. 128.13... Reports on International Capital Transactions and Positions § 128.13 Special survey reports. The Secretary may prescribe special survey reports at such times as the Secretary determines there is a need for...

31 CFR 128.13 - Special survey reports.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 31 Money and Finance: Treasury 1 2011-07-01 2011-07-01 false Special survey reports. 128.13... Reports on International Capital Transactions and Positions § 128.13 Special survey reports. The Secretary may prescribe special survey reports at such times as the Secretary determines there is a need for...

31 CFR 128.23 - Special survey reports.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 31 Money and Finance: Treasury 1 2014-07-01 2014-07-01 false Special survey reports. 128.23... Reports on Foreign Currency Positions § 128.23 Special survey reports. The Secretary may prescribe special survey reports with respect to foreign exchange positions and related information at such times as the...

10 CFR 835.204 - Planned special exposures.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 10 Energy 4 2010-01-01 2010-01-01 false Planned special exposures. 835.204 Section 835.204 Energy DEPARTMENT OF ENERGY OCCUPATIONAL RADIATION PROTECTION Standards for Internal and External Exposure § 835.204 Planned special exposures. (a) A planned special exposure may be authorized for a radiological worker to...

14 CFR 21.197 - Special flight permits.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Special flight permits. 21.197 Section 21... CERTIFICATION PROCEDURES FOR PRODUCTS AND PARTS Airworthiness Certificates § 21.197 Special flight permits. (a) A special flight permit may be issued for an aircraft that may not currently meet applicable...

14 CFR 21.197 - Special flight permits.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 1 2014-01-01 2014-01-01 false Special flight permits. 21.197 Section 21... CERTIFICATION PROCEDURES FOR PRODUCTS AND PARTS Airworthiness Certificates § 21.197 Special flight permits. (a) A special flight permit may be issued for an aircraft that may not currently meet applicable...

14 CFR 21.197 - Special flight permits.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Special flight permits. 21.197 Section 21... CERTIFICATION PROCEDURES FOR PRODUCTS AND PARTS Airworthiness Certificates § 21.197 Special flight permits. (a) A special flight permit may be issued for an aircraft that may not currently meet applicable...

10 CFR 490.602 - Special orders.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 10 Energy 3 2013-01-01 2013-01-01 false Special orders. 490.602 Section 490.602 Energy DEPARTMENT OF ENERGY ENERGY CONSERVATION ALTERNATIVE FUEL TRANSPORTATION PROGRAM Investigations and Enforcement § 490.602 Special orders. (a) DOE may require by general or special orders that any person— (1) File, in...

10 CFR 490.602 - Special orders.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 10 Energy 3 2012-01-01 2012-01-01 false Special orders. 490.602 Section 490.602 Energy DEPARTMENT OF ENERGY ENERGY CONSERVATION ALTERNATIVE FUEL TRANSPORTATION PROGRAM Investigations and Enforcement § 490.602 Special orders. (a) DOE may require by general or special orders that any person— (1) File, in...

10 CFR 490.602 - Special orders.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 10 Energy 3 2014-01-01 2014-01-01 false Special orders. 490.602 Section 490.602 Energy DEPARTMENT OF ENERGY ENERGY CONSERVATION ALTERNATIVE FUEL TRANSPORTATION PROGRAM Investigations and Enforcement § 490.602 Special orders. (a) DOE may require by general or special orders that any person— (1) File, in...

10 CFR 490.602 - Special orders.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 10 Energy 3 2011-01-01 2011-01-01 false Special orders. 490.602 Section 490.602 Energy DEPARTMENT OF ENERGY ENERGY CONSERVATION ALTERNATIVE FUEL TRANSPORTATION PROGRAM Investigations and Enforcement § 490.602 Special orders. (a) DOE may require by general or special orders that any person— (1) File, in...

10 CFR 490.602 - Special orders.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 10 Energy 3 2010-01-01 2010-01-01 false Special orders. 490.602 Section 490.602 Energy DEPARTMENT OF ENERGY ENERGY CONSERVATION ALTERNATIVE FUEL TRANSPORTATION PROGRAM Investigations and Enforcement § 490.602 Special orders. (a) DOE may require by general or special orders that any person— (1) File, in...

28 CFR 52.01 - Civil proceedings: Special master, pretrial, trial, appeal.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 28 Judicial Administration 2 2014-07-01 2014-07-01 false Civil proceedings: Special master...) PROCEEDINGS BEFORE U.S. MAGISTRATE JUDGES § 52.01 Civil proceedings: Special master, pretrial, trial, appeal... as special master, if the attorney, with the concurrence of his or her supervisor, determines that...

28 CFR 52.01 - Civil proceedings: Special master, pretrial, trial, appeal.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 28 Judicial Administration 2 2011-07-01 2011-07-01 false Civil proceedings: Special master...) PROCEEDINGS BEFORE U.S. MAGISTRATE JUDGES § 52.01 Civil proceedings: Special master, pretrial, trial, appeal... as special master, if the attorney, with the concurrence of his or her supervisor, determines that...

28 CFR 52.01 - Civil proceedings: Special master, pretrial, trial, appeal.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 28 Judicial Administration 2 2013-07-01 2013-07-01 false Civil proceedings: Special master...) PROCEEDINGS BEFORE U.S. MAGISTRATE JUDGES § 52.01 Civil proceedings: Special master, pretrial, trial, appeal... as special master, if the attorney, with the concurrence of his or her supervisor, determines that...

28 CFR 52.01 - Civil proceedings: Special master, pretrial, trial, appeal.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 28 Judicial Administration 2 2012-07-01 2012-07-01 false Civil proceedings: Special master...) PROCEEDINGS BEFORE U.S. MAGISTRATE JUDGES § 52.01 Civil proceedings: Special master, pretrial, trial, appeal... as special master, if the attorney, with the concurrence of his or her supervisor, determines that...

40 CFR 1054.640 - What special provisions apply to branded engines?

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 32 2010-07-01 2010-07-01 false What special provisions apply to branded engines? 1054.640 Section 1054.640 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... EQUIPMENT Special Compliance Provisions § 1054.640 What special provisions apply to branded engines? The...

40 CFR 1039.640 - What special provisions apply to branded engines?

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 32 2010-07-01 2010-07-01 false What special provisions apply to branded engines? 1039.640 Section 1039.640 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... ENGINES Special Compliance Provisions § 1039.640 What special provisions apply to branded engines? The...

40 CFR 1045.640 - What special provisions apply to branded engines?

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 32 2010-07-01 2010-07-01 false What special provisions apply to branded engines? 1045.640 Section 1045.640 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... VESSELS Special Compliance Provisions § 1045.640 What special provisions apply to branded engines? The...

14 CFR 147.19 - Materials, special tools, and shop equipment requirements.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 3 2014-01-01 2014-01-01 false Materials, special tools, and shop... TECHNICIAN SCHOOLS Certification Requirements § 147.19 Materials, special tools, and shop equipment... additional rating, must have an adequate supply of material, special tools, and such of the shop equipment as...

14 CFR 147.19 - Materials, special tools, and shop equipment requirements.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 3 2013-01-01 2013-01-01 false Materials, special tools, and shop... TECHNICIAN SCHOOLS Certification Requirements § 147.19 Materials, special tools, and shop equipment... additional rating, must have an adequate supply of material, special tools, and such of the shop equipment as...

14 CFR 147.19 - Materials, special tools, and shop equipment requirements.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 3 2011-01-01 2011-01-01 false Materials, special tools, and shop... TECHNICIAN SCHOOLS Certification Requirements § 147.19 Materials, special tools, and shop equipment... additional rating, must have an adequate supply of material, special tools, and such of the shop equipment as...

14 CFR 147.19 - Materials, special tools, and shop equipment requirements.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 3 2012-01-01 2012-01-01 false Materials, special tools, and shop... TECHNICIAN SCHOOLS Certification Requirements § 147.19 Materials, special tools, and shop equipment... additional rating, must have an adequate supply of material, special tools, and such of the shop equipment as...

28 CFR 44.304 - Special Counsel acting on own initiative.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 28 Judicial Administration 2 2010-07-01 2010-07-01 false Special Counsel acting on own initiative...-RELATED EMPLOYMENT PRACTICES Enforcement Procedures § 44.304 Special Counsel acting on own initiative. (a) The Special Counsel may, on his or her own initiative, conduct investigations respecting unfair...

14 CFR 25.619 - Special factors.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Special factors. 25.619 Section 25.619... STANDARDS: TRANSPORT CATEGORY AIRPLANES Design and Construction General § 25.619 Special factors. The factor of safety prescribed in § 25.303 must be multiplied by the highest pertinent special factor of safety...

7 CFR 29.3057 - Special factor.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 2 2010-01-01 2010-01-01 false Special factor. 29.3057 Section 29.3057 Agriculture... Special factor. A symbol or term authorized to be used with specified grades. Tobacco to which a special factor is applied may meet the general specifications but has a peculiar side or characteristic which...

7 CFR 29.2299 - Special factor.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 2 2010-01-01 2010-01-01 false Special factor. 29.2299 Section 29.2299 Agriculture... Special factor. A symbol or term authorized to be used with specified grades. Tobacco to which a special factor is applied may meet the general specifications but has a peculiar side or characteristic which...

47 CFR 73.1515 - Special field test authorizations.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 47 Telecommunication 4 2014-10-01 2014-10-01 false Special field test authorizations. 73.1515 Section 73.1515 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) BROADCAST RADIO SERVICES RADIO BROADCAST SERVICES Rules Applicable to All Broadcast Stations § 73.1515 Special field test authorizations. (a) A special field test...

47 CFR 73.1515 - Special field test authorizations.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 47 Telecommunication 4 2012-10-01 2012-10-01 false Special field test authorizations. 73.1515 Section 73.1515 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) BROADCAST RADIO SERVICES RADIO BROADCAST SERVICES Rules Applicable to All Broadcast Stations § 73.1515 Special field test authorizations. (a) A special field test...

46 CFR 153.565 - Special requirement for temperature sensors.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 5 2011-10-01 2011-10-01 false Special requirement for temperature sensors. 153.565... CARGOES SHIPS CARRYING BULK LIQUID, LIQUEFIED GAS, OR COMPRESSED GAS HAZARDOUS MATERIALS Design and Equipment Special Requirements § 153.565 Special requirement for temperature sensors. If a cargo listed in...

46 CFR 153.565 - Special requirement for temperature sensors.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 5 2010-10-01 2010-10-01 false Special requirement for temperature sensors. 153.565... CARGOES SHIPS CARRYING BULK LIQUID, LIQUEFIED GAS, OR COMPRESSED GAS HAZARDOUS MATERIALS Design and Equipment Special Requirements § 153.565 Special requirement for temperature sensors. If a cargo listed in...

49 CFR 1242.04 - Special tests.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 49 Transportation 9 2014-10-01 2014-10-01 false Special tests. 1242.04 Section 1242.04... BETWEEN FREIGHT SERVICE AND PASSENGER SERVICE FOR RAILROADS 1 General § 1242.04 Special tests. When the separation of common expense accounts between freight and passenger services is based upon special tests or...

50 CFR 26.33 - Special regulations.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 50 Wildlife and Fisheries 6 2010-10-01 2010-10-01 false Special regulations. 26.33 Section 26.33... NATIONAL WILDLIFE REFUGE SYSTEM PUBLIC ENTRY AND USE Public Use and Recreation § 26.33 Special regulations. (a) Special regulations shall be issued for public use, access, and recreation within certain...

50 CFR 26.33 - Special regulations.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 50 Wildlife and Fisheries 8 2011-10-01 2011-10-01 false Special regulations. 26.33 Section 26.33... NATIONAL WILDLIFE REFUGE SYSTEM PUBLIC ENTRY AND USE Public Use and Recreation § 26.33 Special regulations. (a) Special regulations shall be issued for public use, access, and recreation within certain...

19 CFR 201.27 - Special procedures: Medical records.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 19 Customs Duties 3 2014-04-01 2014-04-01 false Special procedures: Medical records. 201.27... APPLICATION Safeguarding Individual Privacy Pursuant to 5 U.S.C. 552a § 201.27 Special procedures: Medical... maintained by the Commission which pertain to him or her, medical and psychological records merit special...

33 CFR 62.31 - Special marks.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 33 Navigation and Navigable Waters 1 2012-07-01 2012-07-01 false Special marks. 62.31 Section 62.31 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY AIDS TO NAVIGATION UNITED STATES AIDS TO NAVIGATION SYSTEM The U.S. Aids to Navigation System § 62.31 Special marks. Special...

33 CFR 62.31 - Special marks.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 33 Navigation and Navigable Waters 1 2013-07-01 2013-07-01 false Special marks. 62.31 Section 62.31 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY AIDS TO NAVIGATION UNITED STATES AIDS TO NAVIGATION SYSTEM The U.S. Aids to Navigation System § 62.31 Special marks. Special...

33 CFR 62.31 - Special marks.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 33 Navigation and Navigable Waters 1 2014-07-01 2014-07-01 false Special marks. 62.31 Section 62.31 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY AIDS TO NAVIGATION UNITED STATES AIDS TO NAVIGATION SYSTEM The U.S. Aids to Navigation System § 62.31 Special marks. Special...

33 CFR 62.31 - Special marks.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 33 Navigation and Navigable Waters 1 2011-07-01 2011-07-01 false Special marks. 62.31 Section 62.31 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY AIDS TO NAVIGATION UNITED STATES AIDS TO NAVIGATION SYSTEM The U.S. Aids to Navigation System § 62.31 Special marks. Special...

7 CFR 767.202 - Real estate inventory property located in special hazard areas.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 7 2010-01-01 2010-01-01 false Real estate inventory property located in special...) FARM SERVICE AGENCY, DEPARTMENT OF AGRICULTURE SPECIAL PROGRAMS INVENTORY PROPERTY MANAGEMENT Real Estate Property With Important Resources or Located in Special Hazard Areas § 767.202 Real estate...

7 CFR 767.202 - Real estate inventory property located in special hazard areas.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 7 Agriculture 7 2012-01-01 2012-01-01 false Real estate inventory property located in special...) FARM SERVICE AGENCY, DEPARTMENT OF AGRICULTURE SPECIAL PROGRAMS INVENTORY PROPERTY MANAGEMENT Real Estate Property With Important Resources or Located in Special Hazard Areas § 767.202 Real estate...

7 CFR 767.202 - Real estate inventory property located in special hazard areas.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 7 Agriculture 7 2014-01-01 2014-01-01 false Real estate inventory property located in special...) FARM SERVICE AGENCY, DEPARTMENT OF AGRICULTURE SPECIAL PROGRAMS INVENTORY PROPERTY MANAGEMENT Real Estate Property With Important Resources or Located in Special Hazard Areas § 767.202 Real estate...

7 CFR 767.202 - Real estate inventory property located in special hazard areas.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 7 Agriculture 7 2013-01-01 2013-01-01 false Real estate inventory property located in special...) FARM SERVICE AGENCY, DEPARTMENT OF AGRICULTURE SPECIAL PROGRAMS INVENTORY PROPERTY MANAGEMENT Real Estate Property With Important Resources or Located in Special Hazard Areas § 767.202 Real estate...

7 CFR 767.202 - Real estate inventory property located in special hazard areas.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 7 2011-01-01 2011-01-01 false Real estate inventory property located in special...) FARM SERVICE AGENCY, DEPARTMENT OF AGRICULTURE SPECIAL PROGRAMS INVENTORY PROPERTY MANAGEMENT Real Estate Property With Important Resources or Located in Special Hazard Areas § 767.202 Real estate...

47 CFR 61.17 - Method of filing applications for special permission.

Code of Federal Regulations, 2010 CFR

2010-10-01

... special permission. (a) An application for special permission filed electronically must be addressed to... permission applications requiring fees as set forth in part 1, subpart G of this chapter, issuing carriers... 47 Telecommunication 3 2010-10-01 2010-10-01 false Method of filing applications for special...

14 CFR 399.35 - Special tariff permission.

Code of Federal Regulations, 2010 CFR

2010-01-01

... Special tariff permission. (a) Definition. As used in this section, to grant STP means to approve a carrier's application for Special Tariff Permission to file a tariff on less than the statutory notice set... 14 Aeronautics and Space 4 2010-01-01 2010-01-01 false Special tariff permission. 399.35 Section...

12 CFR 226.46 - Special disclosure requirements for private education loans.

Code of Federal Regulations, 2010 CFR

2010-01-01

... GOVERNORS OF THE FEDERAL RESERVE SYSTEM TRUTH IN LENDING (REGULATION Z) Special Rules for Private Education Loans § 226.46 Special disclosure requirements for private education loans. (a) Coverage. The... 12 Banks and Banking 3 2010-01-01 2010-01-01 false Special disclosure requirements for private...

34 CFR 373.1 - What is the purpose of the Special Demonstration Programs?

Code of Federal Regulations, 2010 CFR

2010-07-01

... 34 Education 2 2010-07-01 2010-07-01 false What is the purpose of the Special Demonstration Programs? 373.1 Section 373.1 Education Regulations of the Offices of the Department of Education (Continued) OFFICE OF SPECIAL EDUCATION AND REHABILITATIVE SERVICES, DEPARTMENT OF EDUCATION SPECIAL...

10 CFR 835.204 - Planned special exposures.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 10 Energy 4 2011-01-01 2011-01-01 false Planned special exposures. 835.204 Section 835.204 Energy DEPARTMENT OF ENERGY OCCUPATIONAL RADIATION PROTECTION Standards for Internal and External Exposure § 835.204 Planned special exposures. (a) A planned special exposure may be authorized for a radiological worker to...

10 CFR 835.204 - Planned special exposures.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 10 Energy 4 2014-01-01 2014-01-01 false Planned special exposures. 835.204 Section 835.204 Energy DEPARTMENT OF ENERGY OCCUPATIONAL RADIATION PROTECTION Standards for Internal and External Exposure § 835.204 Planned special exposures. (a) A planned special exposure may be authorized for a radiological worker to...

10 CFR 835.204 - Planned special exposures.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 10 Energy 4 2012-01-01 2012-01-01 false Planned special exposures. 835.204 Section 835.204 Energy DEPARTMENT OF ENERGY OCCUPATIONAL RADIATION PROTECTION Standards for Internal and External Exposure § 835.204 Planned special exposures. (a) A planned special exposure may be authorized for a radiological worker to...

10 CFR 835.204 - Planned special exposures.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 10 Energy 4 2013-01-01 2013-01-01 false Planned special exposures. 835.204 Section 835.204 Energy DEPARTMENT OF ENERGY OCCUPATIONAL RADIATION PROTECTION Standards for Internal and External Exposure § 835.204 Planned special exposures. (a) A planned special exposure may be authorized for a radiological worker to...

46 CFR 153.545 - Special requirements for liquid sulfur.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 5 2014-10-01 2014-10-01 false Special requirements for liquid sulfur. 153.545 Section... CARGOES SHIPS CARRYING BULK LIQUID, LIQUEFIED GAS, OR COMPRESSED GAS HAZARDOUS MATERIALS Design and Equipment Special Requirements § 153.545 Special requirements for liquid sulfur. (a) A containment system...

46 CFR 153.545 - Special requirements for liquid sulfur.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 5 2011-10-01 2011-10-01 false Special requirements for liquid sulfur. 153.545 Section... CARGOES SHIPS CARRYING BULK LIQUID, LIQUEFIED GAS, OR COMPRESSED GAS HAZARDOUS MATERIALS Design and Equipment Special Requirements § 153.545 Special requirements for liquid sulfur. (a) A containment system...