Marine forearc extension in the Hikurangi Margin: New insights from high-resolution 3D seismic data

NASA Astrophysics Data System (ADS)

Böttner, Christoph; Gross, Felix; Geersen, Jacob; Mountjoy, Joshu; Crutchley, Gareth; Krastel, Sebastian

2017-04-01

In subduction zones upper-plate normal faults have long been considered a tectonic feature primarily associated with erosive margins. However, increasing data coverage has proven that similar features also occur in accretionary margins, such as Cascadia, Makran, Nankai or Central Chile, where kinematics are dominated by compression. Considering their wide distribution there is, without doubt, a significant lack of qualitative and quantitative knowledge regarding the role and importance of normal faults and zones of extension for the seismotectonic evolution of accretionary margins. We use a high-resolution 3D P-Cable seismic volume from the Hikurangi Margin acquired in 2014 to analyze the spatial distribution and mechanisms of upper-plate normal faulting. The study area is located at the upper continental slope in the area of the Tuaheni landslide complex. In detail we aim to (1) map the spatial distribution of normal faults and characterize their vertical throws, strike directions, and dip angles; (2) investigate their possible influence on fluid migration in an area, where gas hydrates are present; (3) discuss the mechanisms that may cause extension of the upper-slope in the study area. Beneath the Tuaheni Landslide Complex we mapped about 200 normal faults. All faults have low displacements (<15 m) and dip at high (> 65°) angles. About 71% of the faults dip landward. We found two main strike directions, with the majority of faults striking 350-10°, parallel to the deformation front. A second group of faults strikes 40-60°. The faults crosscut the BSR, which indicates the base of the gas hydrate zone. In combination with seismically imaged bright-spots and pull-up structures, this indicates that the normal faults effectively transport fluids vertically across the base of the gas hydrate zone. Localized uplift, as indicated by the presence of the Tuaheni Ridge, might support normal faulting in the study area. In addition, different subduction rates across the margin may also favor extension between the segments. Future work will help to further untangle the mechanisms that cause extension of the upper continental slope.

A low-angle detachment fault revealed: Three-dimensional images of the S-reflector fault zone along the Galicia passive margin

NASA Astrophysics Data System (ADS)

Schuba, C. Nur; Gray, Gary G.; Morgan, Julia K.; Sawyer, Dale S.; Shillington, Donna J.; Reston, Tim J.; Bull, Jonathan M.; Jordan, Brian E.

2018-06-01

A new 3-D seismic reflection volume over the Galicia margin continent-ocean transition zone provides an unprecedented view of the prominent S-reflector detachment fault that underlies the outer part of the margin. This volume images the fault's structure from breakaway to termination. The filtered time-structure map of the S-reflector shows coherent corrugations parallel to the expected paleo-extension directions with an average azimuth of 107°. These corrugations maintain their orientations, wavelengths and amplitudes where overlying faults sole into the S-reflector, suggesting that the parts of the detachment fault containing multiple crustal blocks may have slipped as discrete units during its late stages. Another interface above the S-reflector, here named S‧, is identified and interpreted as the upper boundary of the fault zone associated with the detachment fault. This layer, named the S-interval, thickens by tens of meters from SE to NW in the direction of transport. Localized thick accumulations also occur near overlying fault intersections, suggesting either non-uniform fault rock production, or redistribution of fault rock during slip. These observations have important implications for understanding how detachment faults form and evolve over time. 3-D seismic reflection imaging has enabled unique insights into fault slip history, fault rock production and redistribution.

Interpretation of shallow crustal structure of the Imperial Valley, California, from seismic reflection profiles

DOE Office of Scientific and Technical Information (OSTI.GOV)

Severson, L.K.

1987-05-01

Eight seismic reflection profiles (285 km total length) from the Imperial Valley, California, were provided to CALCRUST for reprocessing and interpretation. Two profiles were located along the western margin of the valley, five profiles were situated along the eastern margin and one traversed the deepest portion of the basin. These data reveal that the central basin contains a wedge of highly faulted sediments that thins to the east. Most of the faulting is strike-slip but there is evidence for block rotations on the scale of 5 to 10 kilometers within the Brawley Seismic Zone. These lines provide insight into themore » nature of the east and west edges of the Imperial Valley. The basement at the northwestern margin of the valley, to the north of the Superstition Hills, has been normal-faulted and blocks of basement material have ''calved'' into the trough. A blanket of sediments has been deposited on this margin. To the south of the Superstition Hills and Superstition Mountain, the top of the basement is a detachment surface that dips gently into the basin. This margin is also covered by a thick sequence sediments. The basement of the eastern margin consists of metamorphic rocks of the upper plate of the Chocolate Mountain Thrust system underlain by the Orocopia Schist. These rocks dip to the southeast and extend westward to the Sand Hills Fault but do not appear to cross it. Thus, the Sand Hills Fault is interpreted to be the southern extension of the San Andreas Fault. North of the Sand Hills Fault the East Highline Canal seismicity lineament is associated with a strike-slip fault and is probably linked to the Sand Hills Fault. Six geothermal areas crossed by these lines, in agreement with previous studies of geothermal reservoirs, are associated with ''faded'' zones, Bouguer gravity and heat flow maxima, and with higher seismic velocities than surrounding terranes.« less

Large-scale fault interactions at the termination of a subduction margin

NASA Astrophysics Data System (ADS)

Mouslopoulou, V.; Nicol, A., , Prof; Moreno, M.; Oncken, O.; Begg, J.; Kufner, S. K.

2017-12-01

Active subduction margins terminate against, and transfer their slip onto, plate-boundary transform faults. The manner in which plate motion is accommodated and partitioned across such kinematic transitions from thrust to strike-slip faulting over earthquake timescales, is poorly documented. The 2016 November 14th, Mw 7.8 Kaikoura Earthquake provides a rare snapshot of how seismic-slip may be accommodated at the tip of an active subduction margin. Analysis of uplift data collected using a range of techniques (field measurements, GPS, LiDAR) and published mapping coupled with 3D dislocation modelling indicates that earthquake-slip ruptured multiple faults with various orientations and slip mechanisms. Modelled and measured uplift patterns indicate that slip on the plate-interface was minor. Instead, a large offshore thrust fault, modelled to splay-off the plate-interface and to extend to the seafloor up to 15 km east of the South Island, appears to have released subduction-related strain and to have facilitated slip on numerous, strike-slip and oblique-slip faults on its hanging-wall. The Kaikoura earthquake suggests that these large splay-thrust faults provide a key mechanism in the transfer of plate motion at the termination of a subduction margin and represent an important seismic hazard.

Hanging canyons of Haida Gwaii, British Columbia, Canada: Fault-control on submarine canyon geomorphology along active continental margins

NASA Astrophysics Data System (ADS)

Harris, Peter T.; Barrie, J. Vaughn; Conway, Kim W.; Greene, H. Gary

2014-06-01

Faulting commonly influences the geomorphology of submarine canyons that occur on active continental margins. Here, we examine the geomorphology of canyons located on the continental margin off Haida Gwaii, British Columbia, that are truncated on the mid-slope (1200-1400 m water depth) by the Queen Charlotte Fault Zone (QCFZ). The QCFZ is an oblique strike-slip fault zone that has rates of lateral motion of around 50-60 mm/yr and a small convergent component equal to about 3 mm/yr. Slow subduction along the Cascadia Subduction Zone has accreted a prism of marine sediment against the lower slope (1500-3500 m water depth), forming the Queen Charlotte Terrace, which blocks the mouths of submarine canyons formed on the upper slope (200-1400 m water depth). Consequently, canyons along this margin are short (4-8 km in length), closely spaced (around 800 m), and terminate uniformly along the 1400 m isobath, coinciding with the primary fault trend of the QCFZ. Vertical displacement along the fault has resulted in hanging canyons occurring locally. The Haida Gwaii canyons are compared and contrasted with the Sur Canyon system, located to the south of Monterey Bay, California, on a transform margin, which is not blocked by any accretionary prism, and where canyons thus extend to 4000 m depth, across the full breadth of the slope.

Quantitative calculation and numerical modeling of the conjugate margins of the South China Sea

NASA Astrophysics Data System (ADS)

Dong, D.; Pérez-Gussinyé, M.; Wang, W.; Bai, Y.

2017-12-01

South China margin rifted on the tectonic setting of the early active continental margin since Cenozoic. The present South China Sea (SCS) opened at 32 Ma and showed propagation from east to west, with different crustal and sedimentary structures at the conjugate continental margins. Based on the latest high-quality multi-channel seismic data, bathymetric data, and other obtained seismic profiles, the asymmetric characteristics between the conjugate margins of the SCS are revealed. Spatial variation of morphology, basement structure and marginal faults are discovered among the SCS margin profiles. We calculate the lithospheric stretching factors and analyze the anomalous post-rift subsidence from two typical seismic profiles in the conjugate margins of the SCS, with integrated method of 2D forward and inversion based on flexural-cantilever model. We propose a differential extension model to explain the spatial differences in the SCS margins and emphasize the role of detachment fault in evolutionary process. Numerical modeling has a great advantage in studying the rifted margin formation mechanism. Dynamic modeling for the formation of asymmetric conjugate margins of the SCS is carried out by solving the thermal-mechanical equation, based on the viscoelastic-plastic model. The results show that the width and symmetry of the margin are controlled by the crustal rheological structure and sedimentation rate. Crust with lower strength is prone to distributed and persistent faulting instead of strain localization, which results in the wider margin. On the contrary, the stronger crust would generate large faults and lead to strain localization in a small amount of them, easier to form narrow continental margin. Large sediment loading is favorable for the development of large faults, meanwhile, the subsequent thermal effect reduces the crustal viscosity. A sudden transition zone of sedimentation rate is prone to strain localization and accelerates the crust rift, which may affect the future break-up. The numerical modeling with full dynamics in SCS needs a further investigation. Acknowledge: This study was supported by the National Natural Science Foundation of China (No. 41476042, 41506055 )

Evolution of the Andaman Sea region: Dextral transtension as consequence of the India-Asia collision

NASA Astrophysics Data System (ADS)

Zhang, L.; Xu, J.; Ben-Avraham, Z.; Kelty, T. K.

2010-12-01

The two gigantic conjugate strike-slip faults: the Altyn Fault and the Sagaing Fault in northwest and southeast of the proto-Tibet plateau respectively, began to form as consequence of initiation of the India-Asia collision at around 50 Ma (Xu, 2005; Xu et al., 2010). The Sagaing Fault, Andaman trench fault as well as the Sumatra Fault controlled the evolution of the Andaman Sea region while the collision proceeded. By synthesis of geometry and rifting history of the Andaman Sea Basin and Mergui Basin and the plate tectonic setting, we suggest the following five-stage evolution model for the Andaman Sea region: (1) dextral pull-apart rifting and seafloor spreading from 50 Ma to 32 Ma; (2) dextral transform margin-type rifting was active in Mergui Basin with principal fault being the Sumatran Fault system, and both the transform margin-type rifting and the dextral pull-apart rifting were coevally active in the Andaman Sea Basin during 32 Ma to 20 Ma, when the Sumatra fault rotated CW enough and obliquity of subduction of the Indian plate motion along the Sumatra trench was enough to trigger the dextral displacement to take place on the Sumatra Fault system and the Mottawi fault; (3) the Alcock and Sewell plateaus formed in the Andaman Sea by the NNW transtension and the transform margin-type rifting continued in the Mergui basin during 20 Ma to 15 Ma; (4) NNW weak transtensional rifting on the Alcock and Sewell plateaus and NW weak transform margin-type rifting continued in the Mergui basin during 15 Ma to 5 Ma; (5)transtensional rifting similar with but more intensive than earlier stage kept on, forming the central Andaman Basin and the East basin, from 5 Ma to present.

Aeromagnetic anomaly patterns reveal buried faults along the eastern margin of the Wilkes Subglacial Basin (East Antarctica)

USGS Publications Warehouse

Armadillo, E.; Ferraccioli, F.; Zunino, A.; Bozzo, E.

2007-01-01

The Wilkes Subglacial Basin (WSB) is the major morphological feature recognized in the hinterland of the Transantarctic Mountains. The origin of this basin remains contentious and relatively poorly understood due to the lack of extensive geophysical exploration. We present a new aeromagnetic anomaly map over the transition between the Transantarctic Mountains and the WSB for an area adjacent to northern Victoria Land. The aeromagnetic map reveals the existence of subglacial faults along the eastern margin of the WSB. These inferred faults connect previously proposed fault zones over Oates Land with those mapped along the Ross Sea Coast. Specifically, we suggest a link between the Matusevich Frature Zone and the Priestley Fault during the Cenozoic. The new evidence for structural control on the eastern margin of the WSB implies that a purely flexural origin for the basin is unlikely.

Structural development of the onshore Otway passive margin (Australia): the interaction of rotating syn-sedimentary faults

NASA Astrophysics Data System (ADS)

Tanner, David C.; Ziesch, Jennifer; Krawczyk, Charlotte M.

2017-04-01

Within the context of long-term CO2 storage integrity, we interpreted the faults within the 2.2 km thick, syn-rift, Late Cretaceous to Recent sediments below the CO2CRC Otway Project site in Australia using a detailed interpretation of a 3-D reflection seismic cube (32.3 km×14.35 km × 4100 ms TWT). All the faults in the onshore Otway passive margin basin in this area were active to varying degrees during sedimentation, between ca. 120 and 50 Ma, before they died out. From analysis of fault juxtaposition and fault tip-line propagation maps, as well as analysis of individual stratigraphic thickness maps, we determine the direction and incremental amount of syn-sedimentary movement on each fault. Thickening of the hanging-walls of the faults occurred, as is typical for syn-sedimentary faults. However, we also determine that substantial local footwall thinning took place. Although the syn-sedimentary behaviour of the faults was constantly maintained until 50 Ma, there were two main phases of footwall thinning, separated by a quiescent phase. We postulate that these phases of footwall thinning represent rotation of the fault blocks that correlate with prograding sediment pulses within the passive margin. The rotation of the fault blocks occurred simultaneously, i.e., they could only rotate if they interacted.

Faults Diagnostics of Railway Axle Bearings Based on IMF’s Confidence Index Algorithm for Ensemble EMD

PubMed Central

Yi, Cai; Lin, Jianhui; Zhang, Weihua; Ding, Jianming

2015-01-01

As train loads and travel speeds have increased over time, railway axle bearings have become critical elements which require more efficient non-destructive inspection and fault diagnostics methods. This paper presents a novel and adaptive procedure based on ensemble empirical mode decomposition (EEMD) and Hilbert marginal spectrum for multi-fault diagnostics of axle bearings. EEMD overcomes the limitations that often hypothesize about data and computational efforts that restrict the application of signal processing techniques. The outputs of this adaptive approach are the intrinsic mode functions that are treated with the Hilbert transform in order to obtain the Hilbert instantaneous frequency spectrum and marginal spectrum. Anyhow, not all the IMFs obtained by the decomposition should be considered into Hilbert marginal spectrum. The IMFs’ confidence index arithmetic proposed in this paper is fully autonomous, overcoming the major limit of selection by user with experience, and allows the development of on-line tools. The effectiveness of the improvement is proven by the successful diagnosis of an axle bearing with a single fault or multiple composite faults, e.g., outer ring fault, cage fault and pin roller fault. PMID:25970256

Strain distribution across magmatic margins during the breakup stage: Seismicity patterns in the Afar rift zone

NASA Astrophysics Data System (ADS)

Brown, C.; Ebinger, C. J.; Belachew, M.; Gregg, T.; Keir, D.; Ayele, A.; Aronovitz, A.; Campbell, E.

2008-12-01

Fault patterns record the strain history along passive continental margins, but geochronological constraints are, in general, too sparse to evaluate these patterns in 3D. The Afar depression in Ethiopia provides a unique setting to evaluate the time and space relations between faulting and magmatism across an incipient passive margin that formed above a mantle plume. The margin comprises a high elevation flood basalt province with thick, underplated continental crust, a narrow fault-line escarpment underlain by stretched and intruded crust, and a broad zone of highly intruded, mafic crust lying near sealevel. We analyze fault and seismicity patterns across and along the length of the Afar rift zone to determine the spatial distribution of strain during the final stages of continental breakup, and its relation to active magmatism and dike intrusions. Seismicity data include historic data and 2005-2007 data from the collaborative US-UK-Ethiopia Afar Geodynamics Project that includes the 2005-present Dabbahu rift episode. Earthquake epicenters cluster within discrete, 50 km-long magmatic segments that lack any fault linkage. Swarms also cluster along the fault-line scarp between the unstretched and highly stretched Afar rift zone; these earthquakes may signal release of stresses generated by large lateral density contrasts. We compare Coulomb static stress models with focal mechanisms and fault kinematics to discriminate between segmented magma intrusion and crank- arm models for the central Afar rift zone.

Influence of the Kingak Shale ultimate shelf margin on frontal structures of the Brooks Range in the National Petroleum Reserve in Alaska

USGS Publications Warehouse

Stier, Natalie E.; Connors, Christopher D.; Houseknecht, David W.

2014-01-01

The Jurassic–Lower Cretaceous Kingak Shale in the National Petroleum Reserve in Alaska (NPRA) includes several southward-offlapping depositional sequences that culminate in an ultimate shelf margin, which preserves the depositional profile in southern NPRA. The Kingak Shale thins abruptly southward across the ultimate shelf margin and grades into condensed shale, which is intercalated with underlying condensed shale and chert of the Upper Triassic Shublik Formation and overlying condensed shale of the Lower Cretaceous pebble shale unit and the gamma-ray zone (GRZ) of the Hue Shale. This composite of condensed shale forms a thin (≈300-meter) and mechanically weak section between much thicker and mechanically stronger units, including the Sadlerochit and Lisburne Groups below and the sandstone-prone foredeep wedge of the Torok Formation above. Seismic interpretation indicates that the composite condensed section acted as the major detachment during an Early Tertiary phase of deformation in the northern foothills of the Brooks Range and that thrust faults step up northward to the top of the Kingak, or to other surfaces within the Kingak or the overlying Torok. The main structural style is imbricate fault-bend folding, although fault-propagation folding is evident locally, and large-displacement thrust faults incorporate backthrusting to form structural wedges. The Kingak ultimate shelf margin served as a ramp to localize several thrust faults, and the spatial relationship between the ultimate shelf margin and thrust vergence is inferred to have controlled many structures in southern NPRA. For example, the obliqueness of the Carbon Creek anticline relative to other structures in the foothills is the result of northward-verging thrust faults impinging obliquely on the Kingak ultimate shelf margin in southwestern NPRA.

Geology of the Elephanta Island fault zone, western Indian rifted margin, and its significance for understanding the Panvel flexure

NASA Astrophysics Data System (ADS)

Samant, Hrishikesh; Pundalik, Ashwin; D'souza, Joseph; Sheth, Hetu; Lobo, Keegan Carmo; D'souza, Kyle; Patel, Vanit

2017-02-01

The Panvel flexure is a 150-km long tectonic structure, comprising prominently seaward-dipping Deccan flood basalts, on the western Indian rifted margin. Given the active tectonic faulting beneath the Panvel flexure zone inferred from microseismicity, better structural understanding of the region is needed. The geology of Elephanta Island in the Mumbai harbour, famous for the ca. mid-6th century A.D. Hindu rock-cut caves in Deccan basalt (a UNESCO World Heritage site) is poorly known. We describe a previously unreported but well-exposed fault zone on Elephanta Island, consisting of two large faults dipping steeply east-southeast and producing easterly downthrows. Well-developed slickensides and structural measurements indicate oblique slip on both faults. The Elephanta Island fault zone may be the northern extension of the Alibag-Uran fault zone previously described. This and two other known regional faults (Nhava-Sheva and Belpada faults) indicate a progressively eastward step-faulted structure of the Panvel flexure, with the important result that the individual movements were not simply downdip but also oblique-slip and locally even rotational (as at Uran). An interesting problem is the normal faulting, block tectonics and rifting of this region of the crust for which seismological data indicate a normal thickness (up to 41.3 km). A model of asymmetric rifting by simple shear may explain this observation and the consistently landward dips of the rifted margin faults.

Plate Margin Deformation and Active Tectonics Along the Northern Edge of the Yakutat Terrane in the Saint Elias Orogen, Alaska and Yukon, Canada

NASA Technical Reports Server (NTRS)

Bruhn, Ronald L.; Sauber, Jeanne; Cotton, Michele M.; Pavlis, Terry L.; Burgess, Evan; Ruppert, Natalia; Forster, Richard R.

2012-01-01

The northwest directed motion of the Pacific plate is accompanied by migration and collision of the Yakutat terrane into the cusp of southern Alaska. The nature and magnitude of accretion and translation on upper crustal faults and folds is poorly constrained, however, due to pervasive glaciation. In this study we used high-resolution topography, geodetic imaging, seismic, and geologic data to advance understanding of the transition from strike-slip motion on the Fairweather fault to plate margin deformation on the Bagley fault, which cuts through the upper plate of the collisional suture above the subduction megathrust. The Fairweather fault terminates by oblique-extensional splay faulting within a structural syntaxis, allowing rapid tectonic upwelling of rocks driven by thrust faulting and crustal contraction. Plate motion is partly transferred from the Fairweather to the Bagley fault, which extends 125 km farther west as a dextral shear zone that is partly reactivated by reverse faulting. The Bagley fault dips steeply through the upper plate to intersect the subduction megathrust at depth, forming a narrow fault-bounded crustal sliver in the obliquely convergent plate margin. Since . 20 Ma the Bagley fault has accommodated more than 50 km of dextral shearing and several kilometers of reverse motion along its southern flank during terrane accretion. The fault is considered capable of generating earthquakes because it is linked to faults that generated large historic earthquakes, suitably oriented for reactivation in the contemporary stress field, and locally marked by seismicity. The fault may generate earthquakes of Mw <= 7.5.

Extension of the Narmada — Son lineament on the continental margin off Saurashtra, Western India as obtained from magnetic measurements

NASA Astrophysics Data System (ADS)

Bhattacharya, G. C.; Subrahmanyam, V.

1986-12-01

Magnetic total intensity values and bathymetric data collected on the continental margin off Saurashtra were, used to prepare magnetic anomalies and bathymetric contour maps. The magnetic anomalies are considered to have been caused by the Deccan Trap flood basalts which underlie the Tertiary sediments. Interpretation of the magnetic data using two-dimensional modelling method suggests that the magnetic basement is block faulted and deepens in steps from less than 1.0 km in the north to about 8.0 km towards the southern portion of the study area. The WNW-ESE trending faults identified in the present study extend across the Saurashtra continental margin between Porbandar and Veraval and appear to represent a major linear tectonic feature. The relationship of these fault lineaments with the regional tectonic framework have been discussed to indicate that they conform better as the northern boundary faults of the Narmada rift graben on the continental margin off Saurashtra.

The effect of fault-bend folding on seismic velocity in the marginal ridge of accretionary prisms

USGS Publications Warehouse

Cai, Y.; Wang, Chun-Yong; Hwang, W.-t.; Cochrane, G.R.

1995-01-01

Fluid venting in accretionary prisms, which feeds chemosynthetic biological communities, occurs mostly on the marginal thrust ridge. New seismic data for the marginal ridge of the Cascadia prism show significantly lower velocity than that in the adjacent oceanic basin and place important constraints on the interpretations of why fluid venting occurs mostly on the marginal ridge. We employed a finite-element method to analyze a typical fault-bend folding model to explain the phenomenon. The fault in the model is simulated by contact elements. The elements are characterized not only by finite sliding along a slide line, but also by elastoplastic deformation. We present the results of a stress analysis which show that the marginal ridge is under subhorizontal extension and the frontal thrust is under compression. This state of stress favors the growth of tensile cracks in the marginal ridge, facilitates fluid flow and reduces seismic velocities therein; on the other hand, it may close fluid pathways along the frontal thrust and divert fluid flow to the marginal ridge. ?? 1995 Birkha??user Verlag.

Origin of narrow terranes and adjacent major terranes occurring along the denali fault in the eastern and central alaska range, alaska

USGS Publications Warehouse

Nokleberg, W.J.; Richter, D.H.

2007-01-01

Several narrow terranes occur along the Denali fault in the Eastern and Central Alaska Range in Southern Alaska. These terranes are the Aurora Peak, Cottonwood Creek, Maclaren, Pingston, and Windy terranes, and a terrane of ultramafic and associated rocks. Exterior to the narrow terranes to the south is the majorWrangellia island arc composite terrane, and to the north is the major Yukon Tanana metamorphosed continental margin terrane. Overlying mainly the northern margin of the Wrangellia composite terrane are the Kahiltna overlap assemblage to the west, and the Gravina- Nutzotin-Gambier volcanic-plutonic- sedimentary belt to the east and southeast. The various narrow terranes are interpreted as the result of translation of fragments of larger terranes during two major tectonic events: (1) Late Jurassic to mid-Cretaceous accretion of the Wrangellia island arc composite terrane (or superterrane composed of the Wrangellia, Peninsular, and Alexander terranes) and associated subduction zone complexes; and (2) starting in about the Late Cretaceous, dextral transport of the Wrangellia composite terrane along the Denali fault. These two major tectonic events caused: (1) entrapment of a lens of oceanic lithosphere along the suture belt between the Wrangellia composite terrane and the North American Craton Margin and outboard accreted terranes to form the ultramafic and mafic part of the terrane of ultramafic and associated rocks, (2) subsequent dextral translation along the Denali fault of the terrane of ultramafic and associated rocks, (3) dextral translation along the Denali fault of the Aurora Peak, Cottonwood Creek, and Maclaren and continental margin arc terranes from part of the Coast plutonic-metamorphic complex (Coast-North Cascade plutonic belt) in the southwest Yukon Territory or Southeastern Alaska, (4) dextral translation along the Denali fault of the Pingston passive continental margin from a locus along the North American Continental Margin, and (5) formation and dextral transport along the Denali fault of the m??lange of the Windy terrane from fragments of the Gravina-Nutzotin-Gambier volcanic-plutonic-sedimentary belt and from the North American Continental Margin. Copyright ?? 2007 The Geological Society of America.

Origin of a crustal splay fault and its relation to the seismogenic zone and underplating at the erosional north Ecuador-south Colombia oceanic margin

NASA Astrophysics Data System (ADS)

Collot, J.-Y.; Agudelo, W.; Ribodetti, A.; Marcaillou, B.

2008-12-01

Splay faults within accretionary complexes are commonly associated with the updip limit of the seismogenic zone. Prestack depth migration of a multichannel seismic line across the north Ecuador-south Colombia oceanic margin images a crustal splay fault that correlates with the seaward limit of the rupture zone of the 1958 (Mw 7.7) tsunamogenic subduction earthquake. The splay fault separates 5-6.6 km/s velocity, inner wedge basement rocks, which belong to the accreted Gorgona oceanic terrane, from 4 to 5 km/s velocity outer wedge rocks. The outer wedge is dominated by basal tectonic erosion. Despite a 3-km-thick trench fill, subduction of 2-km-high seamount prevented tectonic accretion and promotes basal tectonic erosion. The low-velocity and poorly reflective subduction channel that underlies the outer wedge is associated with the aseismic, décollement thrust. Subduction channel fluids are expected to migrate upward along splay faults and alter outer wedge rocks. Conversely, duplexes are interpreted to form from and above subducting sediment, at ˜14- to 15-km depths between the overlapping seismogenic part of the splay fault and the underlying aseismic décollement. Coeval basal erosion of the outer wedge and underplating beneath the apex of inner wedge control the margin mass budget, which comes out negative. Intraoceanic basement fossil listric normal faults and a rift zone inverted in a flower structure reflect the evolution of the Gorgona terrane from Cretaceous extension to likely Eocene oblique compression. The splay faults could have resulted from tectonic inversion of listric normal faults, thus showing how inherited structures may promote fluid flow across margin basement and control seismogenesis.

Seismic influence in the Quaternary uplift of the Central Chile coastal margin, preliminary results.

NASA Astrophysics Data System (ADS)

Valdivia, D.; del Valle, F.; Marquardt, C.; Elgueta, S.

2017-12-01

In order to quantify the influence of NW striking potentially seismogenic normal faults over the longitudinal variation of the Central Chile Coastal margin uplift, we measured Quaternary marine terraces, which represent the tectonic uplift of the coastal margin. Movement in margin oblique normal faults occurs by co-seismic extension of major subduction earthquakes and has occurred in the Pichilemu fault, generating a 7.0 Mw earthquake after the 2010 8.8 Mw Maule earthquake.The coastal area between 32° and 34° S was selected due to the presence of a well-preserved sequence of 2 to 5 Quaternary marine terraces. In particular, the margin oblique normal NW-trending, SW-dipping Laguna Verde fault, south of Valparaiso (33° S) puts in contact contrasting morphologies: to the south, a flat coast with wide marine terraces is carved in both, Jurassic plutonic rocks and Neogene semi-consolidated marine sediments; to the north, a steeper scarp with narrower marine terraces, over 120 m above the corresponding ones in the southern coast, is carved in Jurassic plutonic rocks.We have collected over 6 months microseimic data, providing information on seismic activity and underground geometry of the Laguna Verde fault. We collected ca. 100 systematic measurements of fringes at the base of paleo coastal scarps through field mapping and a 5 m digital elevation model. These fringes mark the maximum sea level during the terrace's carving.The heights of these fringes range between 0 and 250 masl. We estimate a 0.7 mm/yr slip rate for the Laguna Verde fault based on the height difference between corresponding terraces north- and southward, with an average uplift rate of 0.3 mm/yr for the whole area.NW striking normal faults, besides representing a potential seismic threat to the near population on one of the most densely populated areas of Chile, heavily controls the spatial variation of the coastal margin uplift. In Laguna Verde, the uplift rate differs more than three times northward of the fault.

GLORIA mosaic of the Gulf of Alaska and the British Columbia margin: Deep-sea channels, margin deformation, and the Queen Charlotte fault

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bruns, T.R.; Carlson, P.R.; Stevenson, A.J.

1990-05-01

GLORIA images collected from 1986 to 1989 show sea-floor morphology from the shelf break seaward to 400 km in the Gulf of Alaska and a 70-km-wide swath along British Columbia. Along the Aleutian convergent margin sediment is dominantly trapped in mid-slope basins, where few canyons reach the trench. Accretionary wedge structures range from highly discontinuous to long and continuous. The Yakutat transition margin is either extensively cut by dendritic drainages or, at sea-valley mouths, covered by glacially derived sediment. Young structures underlie the slope from Middleton Island to Pamplona Spur, but are absent from Pamplona Spur to Cross Sound. Alongmore » the southeast Alaska transform margin the Queen Charlotte fault is imaged as a narrow linear feature. The fault steps westward at Tuzo Wilson Knolls, which likely is a spreading ridge segment. Large anticlines lie seaward of and trend parallel to the fault. On the abyssal plain off the Shumagin margin inherited structural and bathymetric features trend parallel to magnetic anomalies, and trench parallel features reflect faulting as the ocean plate bends into the trench. To the north, three turbidite systems drain the margin. The Surveyor system begins between Pamplona Spur and Alsek Canyon and empties into the Aleutian Trench. The Chirikof system arises near Cross Sound and ends in turbidite fans south of the Kodiak-Bowie Seamount chain, a relic Chirikov channel that once carried sediment westward to the Aleutian Trench. The Mukluk and Horizon channels start along southeast Alaska and end 1,000 km away on the Tufts abyssal plain.« less

Passive recording of an active transform, an example from the Levant continental margin and the Dead Sea Fault

NASA Astrophysics Data System (ADS)

Lang, Guy; Lazar, Michael; Schattner, Uri

2017-04-01

Transform faults accommodate lateral motion between two adjacent plates. Records of plate motion and consequent boundary development on land is, at times, scarce and limited to structures along the fault axis. Investigation of a passive continental margin adjacent to the plate boundary might broaden the scope and provide estimates for its structural development. To examine this hypothesis, we analyzed depth and time migrated 3D seismic data together with four boreholes located along the southern Levant continental margin, ca. 100 Km from the continental Dead Sea fault (DSF). The analysis focus on the Plio-Pleistocene sequence, a key period in the development of the DSF. It includes formation of structural maps, stacking pattern investigation and calculation of sedimentation rates based on decompacted 3D depth data. These, in turn, enabled the reconstruction of margin development. This includes Messinian-earliest Zanclean NNE-SSW sinistral strike-slip faulting followed by Zanclean-Late Gelasian syn-depositional folding striking in the same direction. Abrupt change is marked by the Top Gelasian surface that shows indications of regional mass slumping. Successive Mid-Late Pleistocene progradation marks a basinward shift of the depocenter. Progradation controls margin sedimentation rates during the mid-late Pleistocene. These were found to increase throughout the whole Plio-Pleistocene, in contrast to reported sediment discharge from the Nile, which was shown to decrease after the Gelasian. Correlations to onshore findings, suggest that the continental margin records strain localization on the DSF during the Pliocene-Gelasian. This trend peaked at 1.8 Ma when short wavelength strain ceased along the margin, and differential subsidence commenced basinwards. This is attributed to consequent deepening of the DSF plate boundary.

The Rome trough and evolution of the Iapetean margin

DOE Office of Scientific and Technical Information (OSTI.GOV)

Walker, D.; Hamilton-Smith, T.; Drahovzal, J.A.

1991-08-01

Recent structural mapping of the Rome trough suggests a complex structure very different from the symmetrical and laterally continuous graben commonly depicted. Early and Middle Cambrian extension in the Rome trough of eastern Kentucky and adjacent areas resulted in a series of alternately facing half-grabens with variable displacement. These half-grabens are bounded by southwest-northeast-trending normal faults (e.g., Kentucky River and Warfield faults), which are laterally continuous only on the order to tens of kilometers. The Rome trough is laterally segmented by north-south-trending faults (e.g., Lexington fault) commonly expressed as flexures in younger rocks (e.g., Burning Springs anticline and Floyd Countymore » channel). Many of these north-south-trending faults have significant left-lateral displacement, and probably represent reactivated thrust faults of the Grenville tectonic front. The Rome trough and the associated Mississippi Valley, Rough Creek, and Birmingham fault systems were initiated during an Early Cambrian shift in sea-floor spreading from the Blue Ridge-Pine Mountain rift to the Ouachita rift along the Alabama-Oklahoma transform fault. These fault systems have been proposed as having originated from extensional stress propagated northward from the Ouachita rift across the transform fault. In the alternate model proposed here, faulting was brittle, extensional failure resulting form subsidence and flexure of the continental margin to the east. Following initiation of sea-floor spreading at the Blue Ridge-Pine Mountain rift in the latest Proterozoic, margin subsidence in the presence of the Alabama-Oklahoma transform boundary and the inherited Grenville tectonic front resulted in this interior cratonic fault system.« less

Post-rift deformation of the Red Sea Arabian margin

NASA Astrophysics Data System (ADS)

Zanoni, Davide; Schettino, Antonio; Pierantoni, Pietro Paolo; Rasul, Najeeb

2017-04-01

Starting from the Oligocene, the Red Sea rift nucleated within the composite Neoproterozoic Arabian-Nubian shield. After about 30 Ma-long history of continental lithosphere thinning and magmatism, the first pulse of oceanic spreading occurred at around 4.6 Ma at the triple junction of Africa, Arabia, and Danakil plate boundaries and propagated southward separating Danakil and Arabia plates. Ocean floor spreading between Arabia and Africa started later, at about 3 Ma and propagated northward (Schettino et al., 2016). Nowadays the northern part of the Red Sea is characterised by isolated oceanic deeps or a thinned continental lithosphere. Here we investigate the deformation of thinned continental margins that develops as a consequence of the continental lithosphere break-up induced by the progressive oceanisation. This deformation consists of a system of transcurrent and reverse faults that accommodate the anelastic relaxation of the extended margins. Inversion and shortening tectonics along the rifted margins as a consequence of the formation of a new segment of ocean ridge was already documented in the Atlantic margin of North America (e.g. Schlische et al. 2003). We present preliminary structural data obtained along the north-central portion of the Arabian rifted margin of the Red Sea. We explored NE-SW trending lineaments within the Arabian margin that are the inland continuation of transform boundaries between segments of the oceanic ridge. We found brittle fault zones whose kinematics is consistent with a post-rift inversion. Along the southernmost transcurrent fault (Ad Damm fault) of the central portion of the Red Sea we found evidence of dextral movement. Along the northernmost transcurrent fault, which intersects the Harrat Lunayyir, structures indicate dextral movement. At the inland termination of this fault the evidence of dextral movement are weaker and NW-SE trending reverse faults outcrop. Between these two faults we found other dextral transcurrent systems that locally are associated with metre-thick reverse fault zones. Along the analysed faults there is evidence of tectonic reworking. Relict kinematic indicators or the sense of asymmetry of sigmoidal Miocene dykes may suggest that a former sinistral movement was locally accommodated by these faults. This evidence of inversion of strike-slip movement associated with reverse structures, mostly found at the inland endings of these lineaments, suggests an inversion tectonics that could be related to the progressive and recent oceanisation of rift segments. Schettino A., Macchiavelli C., Pierantoni P.P., Zanoni D. & Rasul N. 2016. Recent kinematics of the tectonic plates surrounding the Red Sea and Gulf of Aden. Geophysical Journal International, 207, 457-480. Schlische R.W., Withjack M.O. & Olsen P.E., 2003. Relative timing of CAMP, rifting, continental breakup, and basin inversion: tectonic significance, in The Central Atlantic Magmatic Province: Insights from Fragments of Pangea, eds Hames W., Mchone J.G., Renne P. & Ruppel C., American Geophysical Union, 33-59.

Late Quaternary Faulting along the San Juan de los Planes Fault Zone, Baja California Sur, Mexico

NASA Astrophysics Data System (ADS)

Busch, M. M.; Coyan, J. A.; Arrowsmith, J.; Maloney, S. J.; Gutierrez, G.; Umhoefer, P. J.

2007-12-01

As a result of continued distributed deformation in the Gulf Extensional Province along an oblique-divergent plate margin, active normal faulting is well manifest in southeastern Baja California. By characterizing normal-fault related deformation along the San Juan de los Planes fault zone (SJPFZ) southwest of La Paz, Baja California Sur we contribute to understanding the patterns and rates of faulting along the southwest gulf-margin fault system. The geometry, history, and rate of faulting provide constraints on the relative significance of gulf-margin deformation as compared to axial system deformation. The SJPFZ is a major north-trending structure in the southern Baja margin along which we focused our field efforts. These investigations included: a detailed strip map of the active fault zone, including delineation of active scarp traces and geomorphic surfaces on the hanging wall and footwall; fault scarp profiles; analysis of bedrock structures to better understand how the pattern and rate of strain varied during the development of this fault zone; and a gravity survey across the San Juan de los Planes basin to determine basin geometry and fault behavior. The map covers a N-S swath from the Gulf of California in the north to San Antonio in the south, an area ~45km long and ~1-4km wide. Bedrock along the SJPFZ varies from Cretaceous Las Cruces Granite in the north to Cretaceous Buena Mujer Tonalite in the south and is scarred by shear zones and brittle faults. The active scarp-forming fault juxtaposes bedrock in the footwall against Late Quaternary sandstone-conglomerate. This ~20m wide zone is highly fractured bedrock infused with carbonate. The northern ~12km of the SJPFZ, trending 200°, preserves discontinuous scarps 1-2km long and 1-3m high in Quaternary units. The scarps are separated by stretches of bedrock embayed by hundreds of meters-wide tongues of Quaternary sandstone-conglomerate, implying low Quaternary slip rate. Further south, ~2 km north of the Los Planes highway, the fault steps to the right 2km with no overlap. The fault is inactive until ~3km south of the Los Planes highway where scarp heights in the Quaternary sediments rise to ~3-11m for ~11km with an average trend of 160°, implying increasing slip rate. The fault then steps left 2km with no overlap, trending 145°. Scarp heights range from 3-6m in the step. The southernmost 9km of the fault zone, trending 200°, is marked by discontinuous scarps and embayed bedrock, reflecting diminished fault activity. The footwall landscape in this area is characterized by a broad, gently-sloping, low-relief pediment surface with thin Quaternary cover, disrupted by inselberg-like hills. The young scarp-forming fault appears to have reactivated older faults to rupture this pediment, reflecting the episodic nature of slip along this fault zone. Preliminary OSL ages of the youngest faulted deposit imply a Late Pleistocene-Holocene slip rate of 0.1-1mm/yr. The SJPFZ is thus characterized by reactivation of pre-existing faults to rupture a pre-existing low relief erosional landscape. Whereas the entire region might have experienced the quiescent period that allowed for development of the low- relief, stable surface along the SJPFZ, we speculate that while the SJPFZ was dormant, other faults within the gulf-margin system were actively accommodating strain.

Long-term strain accommodation in the eastern margin of the Tibetan Plateau: Insights from 3D thermo-kinematic modelling

NASA Astrophysics Data System (ADS)

Tian, Y.; Vermeesch, P.; Carter, A.; Zhang, P.

2017-12-01

The Cenozoic deformation of the Tibetan Plateau were dominated by the north-south collision between the Indian and Eurasian continents since Early Cenozoic time. Numerous lines of evidence suggest that the plateau has expanded outward after the collision, forming a diverging stress-regime from the collisional belt to plateau margins. When and how the expansional strain had propagated to the current plateau margins has been hotly debated. This work presents results of an on-going projects for understanding the long-term strain history along the Longmen Shan, the eastern margin of the Tibetan Plateau, where deformation is controlled by three parallel NW-dipping faults. From foreland (southeast) to hinterland (northwest), the main faults are the Guanxian-Anxian fault, Yingxiu-Beichuan fault and Wenchuan-Maowen fault. Exhumation pattern constrained by one-dimensional modelling made from a compilation of published and unpublished thermochronometry data shows a strong structural control, with highest amounts of exhumation in the hinterland region, a pattern that is characteristic of out-of-sequence reverse faulting (Tian et al., 2013, Tectonics, doi:10.1002/tect.20043; Tian et al., 2015, Geophys. Res. Lett., doi:10.1002/2014GL062383). Three-dimensional thermo-kinematic modelling of these data suggests that the Longmen Shan faults are listric in geometry, merging into a detachment at a depth of 20-30 km. The models require a marked decrease in slip-rate along the frontal Yingxiu-Beichuan in the late Miocene, whereas the slip-rate along the hinterland Wenchuan-Maowen fault remained relatively constant since early Miocene time. The long-term pattern of strain accommodation revealed by the three-dimensional thermo-kinematic modelling have important implications for distinguishing geodynamic models proposed for explaining the eastward growth of the Tibetan Plateau.

Structure Deformation of the Minjiang and Huya Fault, the Eastern Margin of the Tibetan Plateau Revealed by Deep Seismic Reflection Profiles

NASA Astrophysics Data System (ADS)

Gao, R.; Wang, H.; Li, W.; Li, H.

2014-12-01

The Minshan region, located along the eastern margin of the Tibetan Plateau north of the Sichuan Basin, provides an important natural laboratory in which to study the patterns of deformation and their relationship to mountain building at the margin of the plateau. The Minshan range is bounded by the Minjiang fault to the west and Huya fault to the east. Evidence from the Neotectonics sediments suggests that deformation along the western Min Shan may reflect the surface response to thickening of a weak lower crust at the margin of the Tibetan Plateau (Kirby et al., 2000). In 2014, two deep seismic profiles was carried out across the Minjiang fault (55 km long) and Huya fault (45 km long) respectively, supported by China geological survey project (No.1212011220260) and Crust Probe Project of China (SinoProbe-02-01). The recording of seismic waves from 4 big shots (500kg), 100 middle shots (120 kg) and 400 small shots (36 kg) were employed. The geophones spacing is 50 m. The preliminary stack sections provide us a detailed deformation mechanism of the Minshan region for the first time. The result shows that: (1) The Huya fault section shows different reflection characteristics on the west and east flank. (2) The Moho reflection beneath the Huya fault, which appeared at 12-13 s two-way time, tilts from the east to the west. (3) The Minjiang fault shows as a series of thrust nappe in the upper crust. (4) A strong reflector appears in the middle crust of the Minjiang section at 8-9 s two-way times, and it dips down to the lower crust from west to east.

States of stress and slip partitioning in a continental scale strike-slip duplex: Tectonic and magmatic implications by means of finite element modeling

NASA Astrophysics Data System (ADS)

Iturrieta, Pablo Cristián; Hurtado, Daniel E.; Cembrano, José; Stanton-Yonge, Ashley

2017-09-01

Orogenic belts at oblique convergent subduction margins accommodate deformation in several trench-parallel domains, one of which is the magmatic arc, commonly regarded as taking up the margin-parallel, strike-slip component. However, the stress state and kinematics of volcanic arcs is more complex than usually recognized, involving first- and second-order faults with distinctive slip senses and mutual interaction. These are usually organized into regional scale strike-slip duplexes, associated with both long-term and short-term heterogeneous deformation and magmatic activity. This is the case of the 1100 km-long Liquiñe-Ofqui Fault System in the Southern Andes, made up of two overlapping margin-parallel master faults joined by several NE-striking second-order faults. We present a finite element model addressing the nature and spatial distribution of stress across and along the volcanic arc in the Southern Andes to understand slip partitioning and the connection between tectonics and magmatism, particularly during the interseismic phase of the subduction earthquake cycle. We correlate the dynamics of the strike-slip duplex with geological, seismic and magma transport evidence documented by previous work, showing consistency between the model and the inferred fault system behavior. Our results show that maximum principal stress orientations are heterogeneously distributed within the continental margin, ranging from 15° to 25° counter-clockwise (with respect to the convergence vector) in the master faults and 10-19° clockwise in the forearc and backarc domains. We calculate the stress tensor ellipticity, indicating simple shearing in the eastern master fault and transpressional stress in the western master fault. Subsidiary faults undergo transtensional-to-extensional stress states. The eastern master fault displays slip rates of 5 to 10 mm/yr, whereas the western and subsidiary faults show slips rates of 1 to 5 mm/yr. Our results endorse that favorably oriented subsidiary faults serve as magma pathways, particularly where they are close to the intersection with a master fault. Also, the slip of a fault segment is enhanced when an adjacent fault kinematics is superimposed on the regional tectonic loading. Hence, finite element models help to understand coupled tectonics and volcanic processes, demonstrating that geological and geophysical observations can be accounted for by a small number of key first order boundary conditions.

Extent and architecture of major fault systems between northern Victoria Land and the eastern margin of the Wilkes Subglacial Basin (East Antarctica)

NASA Astrophysics Data System (ADS)

Armadillo, E.; Ferraccioli, F.; Balbi, P.; Bozzo, E.

2013-12-01

Terrane bounding and intra-terrane faults of the Ross Orogen in East Antarctica are linked to several phases of Cambrian to Ordovician age subduction and accretion along the active paleo-Pacific margin of Gondwana. Here we compile and analyse new enhanced aeromagnetic anomaly images over the Northern Victoria Land (NVL) segment of the Ross Orogen and the eastern margin of the Wilkes Subglacial Basin (WSB) that help constrain the extent and structural architecture of these fault systems and enable us re-assess their tectonic evolution. Long-wavelength magnetic lows and residual Bouguer gravity highs are modelled as several-km thick inverted sedimentary basins of early Cambrian(?) age. Tectonic inversion occurred along major thrust faults during the late stages of the Ross Orogen, forming a major high-grade pop-up structure within the central Wilson Terrane, flanked by lower grade rocks. The Prince Albert Fault System can now be recongnised as being located to the west of the Exiles Thrust fault system rather than representing its southern continuation. Relatively thin sheets of mylonitic sheared granitoids and possible ultramafic lenses are associated with the late-Ross (ca 480 Ma) Exiles Thrust fault system, while significantly larger and thicker batholiths were emplaced along the Prince Albert Fault System. Recent zircon U-Pb dating over small exposures of gabbro-diorites within the Prince Albert Mountains to the south lead us to propose that this part of the magmatic arc was emplaced during an earlier phase of subduction (~520 Ma or older?), compared to the late-Ross intrusions to the east. Whether the Prince Albert Fault System was indeed a major cryptic suture in early Cambrian times (Ferraccioli et al., 2002, GRL) remains speculative, but possible. Our aeromagnetic interpretation leads us to conclude that these inherited terrane bounding and intra-terrane fault systems of the Ross Orogen exerted a key influence on Cenozoic tectonic blocks and faults of the Transantarctic Mountains, and that the eastern margin of the WSB adjacent to NVL was also strongly controlled by a complex array of major intraplate strike-slip fault systems.

Fault evolution in the Potiguar rift termination, equatorial margin of Brazil

NASA Astrophysics Data System (ADS)

de Castro, D. L.; Bezerra, F. H. R.

2015-02-01

The transform shearing between South American and African plates in the Cretaceous generated a series of sedimentary basins on both plate margins. In this study, we use gravity, aeromagnetic, and resistivity surveys to identify architecture of fault systems and to analyze the evolution of the eastern equatorial margin of Brazil. Our study area is the southern onshore termination of the Potiguar rift, which is an aborted NE-trending rift arm developed during the breakup of Pangea. The basin is located along the NNE margin of South America that faces the main transform zone that separates the North and the South Atlantic. The Potiguar rift is a Neocomian structure located at the intersection of the equatorial and western South Atlantic and is composed of a series of NE-trending horsts and grabens. This study reveals new grabens in the Potiguar rift and indicates that stretching in the southern rift termination created a WNW-trending, 10 km wide, and ~ 40 km long right-lateral strike-slip fault zone. This zone encompasses at least eight depocenters, which are bounded by a left-stepping, en echelon system of NW-SE- to NS-striking normal faults. These depocenters form grabens up to 1200 m deep with a rhomb-shaped geometry, which are filled with rift sedimentary units and capped by postrift sedimentary sequences. The evolution of the rift termination is consistent with the right-lateral shearing of the equatorial margin in the Cretaceous and occurs not only at the rift termination but also as isolated structures away from the main rift. This study indicates that the strike-slip shearing between two plates propagated to the interior of one of these plates, where faults with similar orientation, kinematics, geometry, and timing of the major transform are observed. These faults also influence rift geometry.

Tectono-sedimentary evolution of the eastern Gulf of Aden conjugate passive margins: Narrowness and asymmetry in oblique rifting context

NASA Astrophysics Data System (ADS)

Nonn, Chloé; Leroy, Sylvie; Khanbari, Khaled; Ahmed, Abdulhakim

2017-11-01

Here, we focus on the yet unexplored eastern Gulf of Aden, on Socotra Island (Yemen), Southeastern Oman and offshore conjugate passive margins between the Socotra-Hadbeen (SHFZ) and the eastern Gulf of Aden fracture zones. Our interpretation leads to onshore-offshore stratigraphic correlation between the passive margins. We present a new map reflecting the boundaries between the crustal domains (proximal, necking, hyper-extended, exhumed mantle, proto-oceanic and oceanic domains) and structures using bathymetry, magnetic surveys and seismic reflection data. The most striking result is that the magma-poor conjugate margins exhibit asymmetrical architecture since the thinning phase (Upper Rupelian-Burdigalian). Their necking domains are sharp ( 40-10 km wide) and their hyper-extended domains are narrow and asymmetric ( 10-40 km wide on the Socotra margin and 50-80 km wide on the Omani margin). We suggest that this asymmetry is related to the migration of the rift center producing significant lower crustal flow and sequential faulting in the hyper-extended domain. Throughout the Oligo-Miocene rifting, far-field forces dominate and the deformation is accommodated along EW to N110°E northward-dipping low angle normal faults. Convection in the mantle near the SHFZ may be responsible of change in fault dip polarity in the Omani hyper-extended domain. We show the existence of a northward-dipping detachment fault formed at the beginning of the exhumation phase (Burdigalien). It separates the northern upper plate (Oman) from southern lower plate (Socotra Island) and may have generated rift-induced decompression melting and volcanism affecting the upper plate. We highlight multiple generations of detachment faults exhuming serpentinized subcontinental mantle in the ocean-continent transition. Associated to significant decompression melting, final detachment fault may have triggered the formation of a proto-oceanic crust at 17.6 Ma and induced late volcanism up to 10 Ma. Finally, the setting up of a steady-state oceanic spreading center occurs at 17 Ma.

Deciphering the Influence of Crustal Flexure and Shear Along the Margins of the Eastern Snake River Plain

NASA Astrophysics Data System (ADS)

Parker, S. D.

2016-12-01

The kinematic evolution of the eastern Snake River Plain (ESRP) remains highly contested. A lack of strike-slip faults bounding the ESRP serves as a primary assumption in many leading kinematic models. Recent GPS geodesy has highlighted possible shear zones along the ESRP yet regional strike-slip faults remain unidentified. Oblique movement within dense arrays of high-angle conjugate normal faults, paralleling the ESRP, occur within a discrete zone of 50 km on both margins of the ESRP. These features have long been attributed to progressive crustal flexure and subsidence within the ESRP, but are capable of accommodating the observed strain without necessitating large scale strike-slip faults. Deformation features within an extensive Neogene conglomerate provide field evidence for dextral shear in a transtensional system along the northern margin of the ESRP. Pressure-solution pits and cobble striations provide evidence for a horizontal ENE/WSW maximum principal stress orientation, consistent with the hypothesis of a dextral Centennial shear zone. Fold hinges, erosional surfaces and stratigraphic datums plunging perpendicular into the ESRP have been attributed to crustal flexure and subsidence of the ESRP. Similar Quaternary folds plunge obliquely into the ESRP along its margins where diminishing offset along active normal faults trends into linear volcanic features. In all cases, orientations and distributions of plunging fold structures display a correlation to the terminus of active Basin and Range faults and linear volcanic features of the ESRP. An alternative kinematic model, rooted in kinematic disparities between Basin and Range faults and parallelling volcanic features may explain the observed downwarping as well as provide a mechanism for the observed shear along the margins of the ESRP. By integrating field observations with seismic, geodetic and geomorphic observations this study attempts to decipher the signatures of crustal flexure and shear along the margins of the ESRP. Decoupling the influence of these distinct processes on deformation features bounding the ESRP will aid in our understanding of the kinematic evolution of this highly complex region.

The western limits of the Seattle fault zone and its interaction with the Olympic Peninsula, Washington

USGS Publications Warehouse

A.P. Lamb,; L.M. Liberty,; Blakely, Richard J.; Pratt, Thomas L.; Sherrod, B.L.; Van Wijk, K.

2012-01-01

We present evidence that the Seattle fault zone of Washington State extends to the west edge of the Puget Lowland and is kinemati-cally linked to active faults that border the Olympic Massif, including the Saddle Moun-tain deformation zone. Newly acquired high-resolution seismic reflection and marine magnetic data suggest that the Seattle fault zone extends west beyond the Seattle Basin to form a >100-km-long active fault zone. We provide evidence for a strain transfer zone, expressed as a broad set of faults and folds connecting the Seattle and Saddle Mountain deformation zones near Hood Canal. This connection provides an explanation for the apparent synchroneity of M7 earthquakes on the two fault systems ~1100 yr ago. We redefi ne the boundary of the Tacoma Basin to include the previously termed Dewatto basin and show that the Tacoma fault, the southern part of which is a backthrust of the Seattle fault zone, links with a previously unidentifi ed fault along the western margin of the Seattle uplift. We model this north-south fault, termed the Dewatto fault, along the western margin of the Seattle uplift as a low-angle thrust that initiated with exhu-mation of the Olympic Massif and today accommodates north-directed motion. The Tacoma and Dewatto faults likely control both the southern and western boundaries of the Seattle uplift. The inferred strain trans-fer zone linking the Seattle fault zone and Saddle Mountain deformation zone defi nes the northern margin of the Tacoma Basin, and the Saddle Mountain deformation zone forms the northwestern boundary of the Tacoma Basin. Our observations and model suggest that the western portions of the Seattle fault zone and Tacoma fault are com-plex, require temporal variations in principal strain directions, and cannot be modeled as a simple thrust and/or backthrust system.

Continentward-dipping detachment fault system and asymmetric rift structure of the Baiyun Sag, northern South China Sea

NASA Astrophysics Data System (ADS)

Zhou, Zhichao; Mei, Lianfu; Liu, Jun; Zheng, Jinyun; Chen, Liang; Hao, Shihao

2018-02-01

The rift architecture and deep crustal structure of the distal margin at the mid-northern margin of the South China Sea have been previously investigated by using deep seismic reflection profiles. However, one fundamental recurring problem in the debate is the extensional fault system and rift structure of the hyperextended rift basins (Baiyun Sag and Liwan Sag) within the distal margin because of the limited amount of seismic data. Based on new 3D seismic survey data and 2D seismic reflection profiles, we observe an array of fault blocks in the Baiyun Sag, which were tilted towards the ocean by extensional faulting. The extensional faults consistently dip towards the continent. Beneath the tilted fault blocks and extensional faults, a low-angle, high-amplitude and continuous reflection has been interpreted as the master detachment surface that controls the extension process. During rifting, the continentward-dipping normal faults evolved in a sequence from south to north, generating the asymmetric rift structure of the Baiyun Sag. The Baiyun Sag is separated from the oceanic domain by a series of structural highs that were uplifted by magmatic activity in response to the continental breakup at 33 Ma and a ridge jump to the south at 26-24 Ma. Therefore, we propose that magmatism played a significant role in the continental extension and final breakup in the South China Sea.

Sources of Seismic Hazard in British Columbia: What Controls Earthquakes in the Crust?

NASA Astrophysics Data System (ADS)

Balfou, Natalie Joy

This thesis examines processes causing faulting in the North American crust in the northern Cascadia subduction zone. A combination of seismological methods, including source mechanism determination, stress inversion and earthquake relocations are used to determine where earthquakes occur and what forces influence faulting. We also determine if forces that control faulting can be monitored using seismic anisotropy. Investigating the processes that contribute to faulting in the crust is important because these earthquakes pose significant hazard to the large population centres in British Columbia and Washington State. To determine where crustal earthquakes occur we apply double-difference earthquake relocation techniques to events in the Fraser River Valley, British Columbia, and the San Juan Islands, Washington. This technique is used to identify "hidden" active structures using both catalogue and waveform cross-correlation data. Results have significantly reduced uncertainty over routine catalogue locations and show lineations in areas of clustered seismicity. In the Fraser River Valley these lineations or streaks appear to be hidden structures that do not disrupt near-surface sediments; however, in the San Juan Islands the identified lineation can be related to recently mapped surface expressions of faults. To determine forces that influence faulting we investigate the orientation and sources of stress using Bayesian inversion results from focal mechanism data. More than ˜600 focal mechanisms from crustal earthquakes are calculated to identify the dominant style of faulting and inverted to estimate the principal stress orientations and the stress ratio. Results indicate the maximum horizontal compressive stress (SHmax) orientation changes with distance from the subduction interface, from margin-normal along the coast to margin-parallel further inland. We relate the margin-normal stress direction to subduction-related strain rates due to the locked interface between the North America and Juan de Fuca plates just west of Vancouver Island. Further from the margin the plates are coupled less strongly and the margin-parallel SHmax relates to the northward push of the Oregon Block. Active faults around the region are generally thrust faults that strike east-west and might accommodate the margin- parallel compression. Finally, we consider whether crustal anisotropy can be used as a stress monitoring tool in this region. We identify sources and variations of crustal anisotropy using shear-wave splitting analysis on local crustal earthquakes. Results show spatial variations in fast directions, with margin-parallel fast directions at most stations and margin-perpendicular fast directions at stations in the northeast of the region. To use seismic anisotropy as a stress indicator requires identifying which stations are pri- marily influenced by stress. We determine the source of anisotropy at each station by comparing fast directions from shear-wave splitting results to the SHmax orientation. Most stations show agreement between these directions suggesting that anisotropy is stress-related. These stations are further analysed for temporal variations and show variation that could be associated with earthquakes (ML 3{5) and episodic tremor and slip events. The combination of earthquake relocations, source mechanisms, stress and anisotropy is unique and provides a better understanding of faulting and stress in the crust of northern Cascadia.

Fault linkage and continental breakup

NASA Astrophysics Data System (ADS)

Cresswell, Derren; Lymer, Gaël; Reston, Tim; Stevenson, Carl; Bull, Jonathan; Sawyer, Dale; Morgan, Julia

2017-04-01

The magma-poor rifted margin off the west coast of Galicia (NW Spain) has provided some of the key observations in the development of models describing the final stages of rifting and continental breakup. In 2013, we collected a 68 x 20 km 3D seismic survey across the Galicia margin, NE Atlantic. Processing through to 3D Pre-stack Time Migration (12.5 m bin-size) and 3D depth conversion reveals the key structures, including an underlying detachment fault (the S detachment), and the intra-block and inter-block faults. These data reveal multiple phases of faulting, which overlap spatially and temporally, have thinned the crust to between zero and a few km thickness, producing 'basement windows' where crustal basement has been completely pulled apart and sediments lie directly on the mantle. Two approximately N-S trending fault systems are observed: 1) a margin proximal system of two linked faults that are the upward extension (breakaway faults) of the S; in the south they form one surface that splays northward to form two faults with an intervening fault block. These faults were thus demonstrably active at one time rather than sequentially. 2) An oceanward relay structure that shows clear along strike linkage. Faults within the relay trend NE-SW and heavily dissect the basement. The main block bounding faults can be traced from the S detachment through the basement into, and heavily deforming, the syn-rift sediments where they die out, suggesting that the faults propagated up from the S detachment surface. Analysis of the fault heaves and associated maps at different structural levels show complementary fault systems. The pattern of faulting suggests a variation in main tectonic transport direction moving oceanward. This might be interpreted as a temporal change during sequential faulting, however the transfer of extension between faults and the lateral variability of fault blocks suggests that many of the faults across the 3D volume were active at least in part simultaneously. Alternatively, extension may have varied in direction spatially if it were a rotation about a pole located to the north.

Tectonic evolution of the Qumran Basin from high-resolution 3.5-kHz seismic profiles and its implication for the evolution of the northern Dead Sea Basin

NASA Astrophysics Data System (ADS)

Lubberts, Ronald K.; Ben-Avraham, Zvi

2002-02-01

The Dead Sea Basin is a morphotectonic depression along the Dead Sea Transform. Its structure can be described as a deep rhomb-graben (pull-apart) flanked by two block-faulted marginal zones. We have studied the recent tectonic structure of the northwestern margin of the Dead Sea Basin in the area where the northern strike-slip master fault enters the basin and approaches the western marginal zone (Western Boundary Fault). For this purpose, we have analyzed 3.5-kHz seismic reflection profiles obtained from the northwestern corner of the Dead Sea. The seismic profiles give insight into the recent tectonic deformation of the northwestern margin of the Dead Sea Basin. A series of 11 seismic profiles are presented and described. Although several deformation features can be explained in terms of gravity tectonics, it is suggested that the occurrence of strike-slip in this part of the Dead Sea Basin is most likely. Seismic sections reveal a narrow zone of intensely deformed strata. This zone gradually merges into a zone marked by a newly discovered tectonic depression, the Qumran Basin. It is speculated that both structural zones originate from strike-slip along right-bending faults that splay-off from the Jordan Fault, the strike-slip master fault that delimits the active Dead Sea rhomb-graben on the west. Fault interaction between the strike-slip master fault and the normal faults bounding the transform valley seems the most plausible explanation for the origin of the right-bending splays. We suggest that the observed southward widening of the Dead Sea Basin possibly results from the successive formation of secondary right-bending splays to the north, as the active depocenter of the Dead Sea Basin migrates northward with time.

Linking the tectonic evolution with fluid history in magma-poor rifted margins: tracking mantle- and continental crust-related fluids

NASA Astrophysics Data System (ADS)

Pinto, V. H. G.; Manatschal, G.; Karpoff, A. M.

2014-12-01

The thinning of the crust and the exhumation of subcontinental mantle is accompanied by a series of extensional detachment faults. Exhumation of mantle and crustal rocks is intimately related to percolation of fluids along detachment faults leading to changes in mineralogy and chemistry of the mantle, crustal and sedimentary rocks. Field observation, analytical methods, refraction/reflection and well-core data, allowed us to investigate the role of fluids in the Iberian margin and former Alpine Tethys distal margins and the Pyrenees rifted system. In the continental crust, fluid-rock interaction leads to saussuritization that produces Si and Ca enriched fluids found in forms of veins along the fault zone. In the zone of exhumed mantle, large amounts of water are absorbed in the first 5-6 km of serpentinized mantle, which has the counter-effect of depleting the mantle of elements (e.g., Si, Ca, Mg, Fe, Mn, Ni and Cr) forming mantle-related fluids. Using Cr-Ni-V and Fe-Mn as tracers, we show that in the distal margin, mantle-related fluids used detachment faults as pathways and interacted with the overlying crust, the sedimentary basin and the seawater, while further inward parts of the margin, continental crust-related fluids enriched in Si and Ca impregnated the fault zone and may have affected the sedimentary basin. The overall observations and results enable us to show when, where and how these interactions occurred during the formation of the rifted margin. In a first stage, continental crust-related fluids dominated the rifted systems. During the second stage, mantle-related fluids affected the overlying syn-tectonic sediments through direct migration along detachment faults at the future distal margin. In a third stage, these fluids reached the seafloor, "polluted" the seawater and were absorbed by post-tectonic sediments. We conclude that a significant amount of serpentinization occurred underneath the thinned continental crust, that the mantle-related fluids might have modified the chemical composition of the sediments and seawater. We propose that the chemical signature of serpentinization that occurs during the mantle exhumation is recorded in the sediments and may serve as a proxy to date serpentinization and mantle exhumation in present day magma-poor rifted margins.

The Dauki Thrust Fault and the Shillong Anticline: An incipient plate boundary in NE India?

NASA Astrophysics Data System (ADS)

Ferguson, E. K.; Seeber, L.; Steckler, M. S.; Akhter, S. H.; Mondal, D.; Lenhart, A.

2012-12-01

The Shillong Massif is a regional contractional structure developing across the Assam sliver of the Indian plate near the Eastern Syntaxis between the Himalaya and Burma arcs. Faulting associated with the Shillong Massif is a major source of earthquake hazard. The massif is a composite basement-cored asymmetric anticline and is 100km wide, >350km long and 1.8km high. The high relief southern limb preserves a Cretaceous-Paleocene passive margin sequence despite extreme rainfall while the gentler northern limb is devoid of sedimentary cover. This asymmetry suggests southward growth of the structure. The Dauki fault along the south limb builds this relief. From the south-verging structure, we infer a regional deeply-rooted north-dipping blind thrust fault. It strikes E-W and obliquely intersects the NE-SW margin of India, thus displaying three segments: Western, within continental India; Central, along the former passive margin; and Eastern, overridden by the west-verging Burma accretion system. We present findings from recent geologic fieldwork on the western and central segments. The broadly warped erosional surface of the massif defines a single anticline in the central segment, east of the intersection with the hinge zone of the continental margin buried by the Ganges-Brahmaputra Delta. The south limb of the anticline forms a steep topographic front, but is even steeper structurally as defined by the Cretaceous-Eocene cover. Below it, Sylhet Trap Basalts intrude and cover Precambrian basement. Dikes, presumably parallel to the rifted margin, are also parallel to the front, suggesting thrust reactivation of rift-related faults. Less competent Neogene clastics are preserved only near the base of the mountain front. Drag folds in these rocks suggest north-vergence and a roof thrust above a blind thrust wedge floored by the Dauki thrust fault. West of the hinge zone, the contractional structure penetrates the Indian continent and bifurcates. After branching into the Dapsi Fault, the Dauki Fault continues westward as the erosion-deposition boundary combined with a belt of N-S shortening. The Dapsi thrust fault strikes WNW across the Shillong massif and dips NNE. It is mostly blind below a topographically expressed fold involving basement and passive-margin cover. Recent fieldwork has shown that the fault is better exposed in the west, where eventually Archean basement juxtaposes folded and steeply dipping fluvial sediment. Both Dauki and Dapsi faults probably continue beyond the Brahmaputra River, where extreme fluvial processes mask them. The area between the two faults is a gentle southward monocline with little or no shortening. Thus uplift of this area stems from slip on the Dauki thrust fault, not from pervasive shortening. The Burma foldbelt overrides the Shillong Plateau and is warped but continuous across the eastern segment of the Dauki fault. The Haflong-Naga thrust front north of the Dauki merges with the fold-thrust belt in the Sylhet basin to the south, despite >150km of differential advance due to much greater advance of the accretionary prism in the basin. Where the Dauki and Haflong-Naga thrusts cross, the thrust fronts are nearly parallel and opposite vergence. We trace a Dauki-related topographic front eastward across the Burma Range. This and other evidence suggest that the Dauki Fault continues below the foldbelt.

Volcanic passive margins: another way to break up continents

PubMed Central

Geoffroy, L.; Burov, E. B.; Werner, P.

2015-01-01

Two major types of passive margins are recognized, i.e. volcanic and non-volcanic, without proposing distinctive mechanisms for their formation. Volcanic passive margins are associated with the extrusion and intrusion of large volumes of magma, predominantly mafic, and represent distinctive features of Larges Igneous Provinces, in which regional fissural volcanism predates localized syn-magmatic break-up of the lithosphere. In contrast with non-volcanic margins, continentward-dipping detachment faults accommodate crustal necking at both conjugate volcanic margins. These faults root on a two-layer deformed ductile crust that appears to be partly of igneous nature. This lower crust is exhumed up to the bottom of the syn-extension extrusives at the outer parts of the margin. Our numerical modelling suggests that strengthening of deep continental crust during early magmatic stages provokes a divergent flow of the ductile lithosphere away from a central continental block, which becomes thinner with time due to the flow-induced mechanical erosion acting at its base. Crustal-scale faults dipping continentward are rooted over this flowing material, thus isolating micro-continents within the future oceanic domain. Pure-shear type deformation affects the bulk lithosphere at VPMs until continental breakup, and the geometry of the margin is closely related to the dynamics of an active and melting mantle. PMID:26442807

Volcanic passive margins: another way to break up continents.

PubMed

Geoffroy, L; Burov, E B; Werner, P

2015-10-07

Two major types of passive margins are recognized, i.e. volcanic and non-volcanic, without proposing distinctive mechanisms for their formation. Volcanic passive margins are associated with the extrusion and intrusion of large volumes of magma, predominantly mafic, and represent distinctive features of Larges Igneous Provinces, in which regional fissural volcanism predates localized syn-magmatic break-up of the lithosphere. In contrast with non-volcanic margins, continentward-dipping detachment faults accommodate crustal necking at both conjugate volcanic margins. These faults root on a two-layer deformed ductile crust that appears to be partly of igneous nature. This lower crust is exhumed up to the bottom of the syn-extension extrusives at the outer parts of the margin. Our numerical modelling suggests that strengthening of deep continental crust during early magmatic stages provokes a divergent flow of the ductile lithosphere away from a central continental block, which becomes thinner with time due to the flow-induced mechanical erosion acting at its base. Crustal-scale faults dipping continentward are rooted over this flowing material, thus isolating micro-continents within the future oceanic domain. Pure-shear type deformation affects the bulk lithosphere at VPMs until continental breakup, and the geometry of the margin is closely related to the dynamics of an active and melting mantle.

Advancements in understanding the aeromagnetic expressions of basin-margin faults—An example from San Luis Basin, Colorado

USGS Publications Warehouse

Grauch, V. J.; Bedrosian, Paul A.; Drenth, Benjamin J.

2013-01-01

Herein, we summarize and expand on an investigation of the sources of aeromagnetic anomalies related to faults along the eastern margin of the San Luis Basin, northern Rio Grande Rift, Colorado (Grauch et al., 2010). Similar to the faults examined in the central Rio Grande Rift, magnetic sources can be completely explained by tectonic juxtaposition and produce multiple, vertically stacked magnetic contrasts at individual faults. However, the geologic sources are different. They arise from both the sedimentary cover and the underlying bedrock rather than from stratified sediments. In addition, geologic evidence for secondary growth or destruction of magnetic minerals at the fault zone is lacking.

Continental transform margins : state of art and future milestones

NASA Astrophysics Data System (ADS)

Basile, Christophe

2010-05-01

Transform faults were defined 45 years ago as ‘a new class of fault' (Wilson, 1965), and transform margins were consequently individualized as a new class of continental margins. While transform margins represent 20 to 25 % of the total length of continent-ocean transitions, they were poorly studied, especially when compared with the amount of data, interpretations, models and conceptual progress accumulated on divergent or convergent continental margins. The best studied examples of transform margins are located in the northern part of Norway, south of South Africa, in the gulf of California and on both sides of the Equatorial Atlantic. Here is located the Côte d'Ivoire - Ghana margin, where the more complete data set was acquired, based on numerous geological and geophysical cruises, including ODP Leg 159. The first models that encompassed the structure and evolution of transform margins were mainly driven by plate kinematic reconstructions, and evidenced the diachronic end of tectonic activity and the non-cylindrical character of these margins, with a decreasing strike-slip deformation from the convex to the concave divergent-transform intersections. Further thermo-mechanical models were more specifically designed to explain the vertical displacements along transform margins, and especially the occurrence of high-standing marginal ridges. These thermo-mechanical models involved either heat transfer from oceanic to continental lithospheres across the transform faults or tectonically- or gravity-driven mass transfer in the upper crust. These models were far from fully fit observations, and were frequently dedicated to specific example, and not easily generalizable. Future work on transform continental margins may be expected to fill some scientific gaps, and the definition of working directions can benefit from the studies dedicated to other types of margins. At regional scale the structural and sedimentological variability of transform continental margins has to be emphasized. There is not only one type of transform margins, but as for divergent margins huge changes from one margin to another in both structure and evolution. Multiple types have to be evidenced together with the various parameters that should control the variability. As for divergent margins, special attention should be paid to conjugated transform margins as a tool to assess symmetrical / asymmetrical processes in the oceanic opening. Attention should also be focused on the three-dimensional structure of the intersections between transform and divergent margins, such as the one where the giant oil field Jubilee was recently discovered. There is almost no 3D data available in these area, and their structures still have to be described. An other key point to develop is the mechanical behavior of the lithosphere in and in the vicinity of transform margins. The classical behaviors (isostasy, elastic flexure) have be tested extensively. The localization of the deformation by the transform fault, and the coupling of continental and oceanic lithosphere across the transform fault have to be adressed to understand the evolution of these margins. Again as for divergent margins, new concepts are needed to explain the variations in the post-rift and post-transform subsidence, that can not always be explained by classical subsidence models. But the most remarkable advance in our understanding of transform margins may be related to the study of interactions between the lithosphere and adjacent envelops : deep interactions with the mantle, as underplating, tectonic erosion, or possible lateral crustal flow ; surficial interactions between structural evolution, erosion and sedimentation processes in transform margins may affect the topography and bathymetry, thus the oceanic circulation with possible effects on regional and global climate.

Kinematic Reconstruction of the Costa Rican Margin: Evidence for Discontinuities in Deformation Across the Margin

NASA Astrophysics Data System (ADS)

Gose, B.; Bangs, N. L.; McIntosh, K. D.

2016-12-01

Recently acquired 3D seismic reflection data shows that both in-sequence and out-of sequence faults makeup the interior structure of the Costa Rican convergent margin. Recent studies have found evidence for a phase of accretion that led to the formation of a series of thrust-bounded folds that are easily observable within the margin-wedge fabric. Along a primary 2D transect through the center of the 3D survey, faults partition the outer 23km of the margin into 8 fault-bounded segments that can be divided into two characteristic zones, those closest to the trench (S1-S3) and those furthest (S4-S8) separated by a slope break 10 km from the trench (Fig 1). To better understand the observed structure, each segment was characterized as a fault-propagation fold and geometrically modeled using Paradigm's Geosec 2D software. Kinematic flexural slip modules were applied in order to perform bed-length balancing and generate a geologic reconstruction of the margin. Results show the section of the margin spanning from 3-23km from the deformation front has experienced 27.5% shortening, assuming the interpreted horizons were initially flat and continuous. The individual values for percent shortening are not consistent across the margin but distributed into two zones each with progressively increasing strain in the landward direction. Zone 2 (landward) begins with a percent shortening for S8 at 22% and linearly decreases to 2% shortening as you move seaward to S4. The Zone 1-2 boundary is marked by a slope break coinciding with an increase in percent shortening (S3,15%) followed by less shortening seaward (9%, 8%). Shortening and the associated strain is focused at the landward side of the two zones, within S3 and S8. We conclude that the Costa Rican margin has some degree of mechanical partitioning, with a notable discontinuity in strain patterns occurring 10 km from the trench.

Phanerozoic geological evolution of the Equatorial Atlantic domain

NASA Astrophysics Data System (ADS)

Basile, Christophe; Mascle, Jean; Guiraud, René

2005-10-01

The Phanerozoic geological evolution of the Equatorial Atlantic domain has been controlled since the end of Early Cretaceous by the Romanche and Saint Paul transform faults. These faults did not follow the PanAfrican shear zones, but were surimposed on Palæozoic basins. From Neocomian to Barremian, the Central Atlantic rift propagated southward in Cassiporé and Marajó basins, and the South Atlantic rift propagated northward in Potiguar and Benue basins. During Aptian times, the Equatorial Atlantic transform domain appeared as a transfer zone between the northward propagating tip of South Atlantic and the Central Atlantic. Between the transform faults, oceanic accretion started during Late Aptian in small divergent segments, from south to north: Benin-Mundaú, deep Ivorian basin-Barreirinhas, Liberia-Cassiporé. From Late Aptian to Late Albian, the Togo-Ghana-Ceará basins appeared along the Romanche transform fault, and Côte d'Ivoire-Parà-Maranhão basins along Saint Paul transform fault. They were rapidly subsiding in intra-continental settings. During Late Cretaceous, these basins became active transform continental margins, and passive margins since Santonian times. In the same time, the continental edge uplifted leading either to important erosion on the shelf or to marginal ridges parallel to the transform faults in deeper settings.

Fault-Tolerant Control of ANPC Three-Level Inverter Based on Order-Reduction Optimal Control Strategy under Multi-Device Open-Circuit Fault.

PubMed

Xu, Shi-Zhou; Wang, Chun-Jie; Lin, Fang-Li; Li, Shi-Xiang

2017-10-31

The multi-device open-circuit fault is a common fault of ANPC (Active Neutral-Point Clamped) three-level inverter and effect the operation stability of the whole system. To improve the operation stability, this paper summarized the main solutions currently firstly and analyzed all the possible states of multi-device open-circuit fault. Secondly, an order-reduction optimal control strategy was proposed under multi-device open-circuit fault to realize fault-tolerant control based on the topology and control requirement of ANPC three-level inverter and operation stability. This control strategy can solve the faults with different operation states, and can works in order-reduction state under specific open-circuit faults with specific combined devices, which sacrifices the control quality to obtain the stability priority control. Finally, the simulation and experiment proved the effectiveness of the proposed strategy.

Feedbacks Between Surface Processes and Tectonics at Rifted Margins: a Numerical Approach

NASA Astrophysics Data System (ADS)

Andres-Martinez, M.; Perez-Gussinye, M.; Morgan, J. P.; Armitage, J. J.

2014-12-01

Mantle dynamics drives the rifting of the continents and consequent crustal processes shape the topography of the rifted margins. Surface processes modify the topography by eroding positive reliefs and sedimenting on the basins. This lateral displacement of masses implies a change in the loads during rifting, affecting the architecture of the resulting margins. Furthermore, thermal insulation due to sediments could potentially have an impact on the rheologies, which are proved to be one of the most influential parameters that control the deformation style at the continental margins. In order to understand the feedback between these processes we have developed a numerical geodynamic model based on MILAMIN. Our model consists of a 2D Lagrangian triangular mesh for which velocities, displacements, pressures and temperatures are calculated each time step. The model is visco-elastic and includes a free-surface stabilization algorithm, strain weakening and an erosion/sedimentation algorithm. Sediment loads and temperatures on the sediments are taken into account when solving velocities and temperatures for the whole model. Although surface processes are strongly three-dimensional, we have chosen to study a 2D section parallel to the extension as a first approach. Results show that where sedimentation occurs strain further localizes. This is due to the extra load of the sediments exerting a gravitational force over the topography. We also observed angular unconformities on the sediments due to the rotation of crustal blocks associated with normal faults. In order to illustrate the feedbacks between surface and inner processes we will show a series of models calculated with different rheologies and extension velocities, with and without erosion/sedimentation. We will then discuss to which extent thermal insulation due to sedimentation and increased stresses due to sediment loading affect the geometry and distribution of faulting, the rheology of the lower crust and consequently margin architecture.

High-resolution shallow reflection seismic image and surface evidence of the Upper Tiber Basin active faults (Northern Apennines, Italy)

USGS Publications Warehouse

Donne, D.D.; Plccardi, L.; Odum, J.K.; Stephenson, W.J.; Williams, R.A.

2007-01-01

Shallow seismic reflection prospecting has been carried out in order to investigate the faults that bound to the southwest and northeast the Quaternary Upper Tiber Basin (Northern Apennines, Italy). On the northeastern margin of the basin a ??? 1 km long reflection seismic profile images a fault segment and the associated up to 100 meters thick sediment wedge. Across the southwestern margin a 0.5 km-long seismic profile images a 50-55??-dipping extensional fault, that projects to the scarp at the base of the range-front, and against which a 100 m thick syn-tectonic sediment wedge has formed. The integration of surface and sub-surface data allows to estimate at least 190 meters of vertical displacement along the fault and a slip rate around 0.25 m/kyr. Southwestern fault might also be interpreted as the main splay structure of regional Alto Tiberina extensional fault. At last, the 1917 Monterchi earthquake (Imax=X, Boschi et alii, 2000) is correlable with an activation of the southwestern fault, and thus suggesting the seismogenic character of this latter.

Fault zone structure and seismic reflection characteristics in zones of slow slip and tsunami earthquakes

NASA Astrophysics Data System (ADS)

Bell, Rebecca; Henrys, Stuart; Sutherland, Rupert; Barker, Daniel; Wallace, Laura; Holden, Caroline; Power, William; Wang, Xiaoming; Morgan, Joanna; Warner, Michael; Downes, Gaye

2015-04-01

Over the last couple of decades we have learned that a whole spectrum of different fault slip behaviour takes place on subduction megathrust faults from stick-slip earthquakes to slow slip and stable sliding. Geophysical data, including seismic reflection data, can be used to characterise margins and fault zones that undergo different modes of slip. In this presentation we will focus on the Hikurangi margin, New Zealand, which exhibits marked along-strike changes in seismic behaviour and margin characteristics. Campaign and continuous GPS measurements reveal deep interseismic coupling and deep slow slip events (~30-60 km) at the southern Hikurangi margin. The northern margin, in contrast, experiences aseismic slip and shallow (<10-15 km) slow slip events (SSE) every 18-24 months with equivalent moment magnitudes of Mw 6.5-6.8. Updip of the SSE region two unusual megathrust earthquakes occurred in March and May 1947 with characteristics typical of tsunami earthquakes. The Hikurangi margin is therefore an excellent natural laboratory to study differential fault slip behaviour. Using 2D seismic reflection, magnetic anomaly and geodetic data we observe in the source areas of the 1947 tsunami earthquakes i) low amplitude interface reflectivity, ii) shallower interface relief, iii) bathymetric ridges, iv) magnetic anomaly highs and in the case of the March 1947 earthquake v) stronger geodetic coupling. We suggest that this is due to the subduction of seamounts, similar in dimensions to seamounts observed on the incoming Pacific plate, to depths of <10 km. We propose a source model for the 1947 tsunami earthquakes based on geophysical data and find that extremely low rupture velocities (c. 300 m/s) are required to model the observed large tsunami run-up heights (Bell et al. 2014, EPSL). Our study suggests that subducted topography can cause the nucleation of moderate earthquakes with complex, low velocity rupture scenarios that enhance tsunami waves, and the role of subducted rough topography in seismic hazard should not be under-estimated. 2D seismic reflection data along the northern Hikurangi margin also image thick (c. 2 km) high-amplitude reflectivity zones (HRZ) coinciding broadly with the source areas of shallow SSEs. The HRZ may be the result of high-fluid content within subduction sediments, suggesting fluids may exert an important control on the generation of SSEs by reducing effective stress (Bell et al. 2010, GJI). However, this hypothesis remains untested. In this presentation, using synthetic models, we will discuss planned future applications of an advanced seismic imaging technique called Full-waveform inversion, integrated with drilling, at subduction margins like Hikurangi to recover fault physical properties at high-resolution in 3D to examine the properties of heterogeneous fault zones.

Structure and Stratigraphy of the Rift Basins in the Northern Gulf of California: Results from Analysis of Seismic Reflection and Borehole Data.

NASA Astrophysics Data System (ADS)

Martín, A.; González, M.; Helenes, J.; García, J.; Aragón, M.; Carreño, A.

2008-12-01

The northern Gulf of California contains two parallel, north-south trending rift basin systems separated by a basement-high. The interpretation of several exploration wells, and ~4500 km of seismic reflection data from PEMEX (Mexican national oil company) indicate that the tectonically active basins to the west (Wagner- Consag and Upper Delfin basins) may have initiated synchronously with the now abandoned Tiburón- Tepoca-Altar basins to the east in the Sonora margin. In both basin systems the lower sequence (A) is marine mudstone-siltstone, has parallel reflectors and a largely uniform thickness that reaches up to1.5 km, and gradually pinches out toward the lateral margins. This suggests that the unit was deposited prior to their segmentation by transtensional faulting. Marine microfossils from borehole samples from sequence A in the Tiburón and Consag basins indicates middle Miocene (>11.2 Ma) proto-Gulf conditions. Sequence B conformably overlies sequence A, and is characterized by up to 2 km growth strata with a fanning geometry that show a clear genetic relationship to the major transtensional faults that control the segmentation of the two basin systems. Sequence C in the Tiburón and Tepoca basins is comparatively thin (<800 m) and includes several unconformities, but is much less affected by faulting. In contrast, sequence C in the active Wagner, Consag and Upper Delfin basin is a much thicker (up to 2 km) growth sequence with abundant volcanic intrusions. Marked variations in sequence C in the different basin systems clearly demonstrate a major westward shift of deformation and subsidence at this time. The modern depocenter in Wagner-Consag basins is controlled by the Consag and Wagner faults, which trend parallel to the north ~20 km apart, and show opposite normal offset. These two faults merge at an oblique angle (70°-50°, respectively) into the Cerro Prieto transform fault to the north and likely accommodate an important amount of dextral shear. To the south the Consag and Wagner faults connect with a diffuse zone of deformation defined by a series of NE trending faults with moderate normal displacement in the Upper Delfin basin. These NE-trending faults intersect the northern strand of the Ballenas transform fault along the Baja California margin, whereas the eastern end of the NE-trending faults is poorly defined along the western flank of the central antiform. In summary, sequence A was likely deposited across most of the northern gulf in the late Miocene, sequence B marks the onset of two discrete transtensional basin systems controlled by both low and high-angle faults in late Miocene-Pliocene time, and sequence C marks the regional migration of plate- margin shearing to its present location in the western gulf. Thermal effects associated with abundant volcanism and sedimentation along the western margin of the gulf likely controlled the asymmetric partitioning plate margin and shearing during the most recent phase of oblique rifting.

Late Neogene and Active Tectonics along the Northern Margin of the Central Anatolian Plateau,TURKEY

NASA Astrophysics Data System (ADS)

Yildirim, C.; Schildgen, T. F.; Melnick, D.; Echtler, H. P.; Strecker, M. R.

2009-12-01

Margins of orogenic plateaus are conspicuous geomorphic provinces that archive tectonic and climatic variations related to surface uplift. Their growth is associated with spatial and temporal variations of mode and rate of tectonics and surface processes. Those processes can be strongly linked to the evolution of margins and plateaus thorough time. As one of the major morpho-tectonic provinces of Turkey, the Central Pontides (coinciding with the northern margin of the Central Anatolian Plateau (CAP)) display a remarkable topography and present valuable geologic and geomorphic indicators to identify active tectonics. Morpho-tectonic analysis, geological cross-sections, seismic profiles, and geodetic analysis reveal continuous deformation characterized by brittle faults from Late Miocene to recent across the northern margin of the CAP. In the Sinop Peninsula and offshore in the southern Black Sea, pervasive faulting and folding and uplift of Late Miocene to Quaternary marine deposits is related to active margin tectonics of the offshore southern Black Sea thrust and the onshore Balifaki and Erikli faults. In the Kastamonu-Boyabat sedimentary basin, the Late Miocene to Quaternary continental equivalents are strongly deformed by the Ekinveren Fault. This vergent inverse and thrust fault with overstepping en echelon segments deforms not only Quaternary travertines and conglomerates, but also patterns of the Pleistocene to Holocene drainage systems. In the southern Kastamonu-Boyabat basin, an antithetic thrust fault of the Ekinveren Fault system deformed also Quaternary fluviatile terrace deposits. Farther south, a dextral transpressive splay of the North Anatolian Fault (NAF) deforms pediment surfaces and forms the northern flank of the Ilgaz active mountain range. The Ilgaz Range rises up to 2587 m.a.s.l and is delimited by active segments of the NAF.The Central Pontides are located at the apex of northward convex arc of the NAF. Geodetic analysis indicate a deviation of the slip vectors and strain partitioning in the Central Pontides due to the large restraining bend geometry of the NAF. DEM analysis and field observations reveal that the Central Pontides integrate an active bivergent wedge, indicating out-of sequence thrusting and topographical asymmetry, with a gentle pro-wedge northern slope and a steep retro-wedge southern slopes, and regional surface tilting from south to north. Uplifted presumably Late Pleistocene to Holocene marine terraces 4 to 40 m.a.s.l. along the coast and well developed pediment and fill and strath terrace surfaces ranging from 10 to 300 m above along the Gokirmak and Kizilirmak rivers will provide chronological constraints on the uplift and incision rates of the study area.

The limits of seaward spreading and slope instability at the continental margin offshore Mt Etna, imaged by high-resolution 2D seismic data

NASA Astrophysics Data System (ADS)

Gross, Felix; Krastel, Sebastian; Geersen, Jacob; Behrmann, Jan Hinrich; Ridente, Domenico; Chiocci, Francesco Latino; Bialas, Jörg; Papenberg, Cord; Cukur, Deniz; Urlaub, Morelia; Micallef, Aaron

2016-01-01

Mount Etna is the largest active volcano in Europe. Instability of its eastern flank is well documented onshore, and continuously monitored by geodetic and InSAR measurements. Little is known, however, about the offshore extension of the eastern volcano flank, defining a serious shortcoming in stability models. In order to better constrain the active tectonics of the continental margin offshore the eastern flank of the volcano, we acquired a new high-resolution 2D reflection seismic dataset. The data provide new insights into the heterogeneous geology and tectonics at the continental margin offshore Mt Etna. The submarine realm is characterized by different blocks, which are controlled by local- and regional tectonics. A compressional regime is found at the toe of the continental margin, which is bound to a complex basin system. Both, the clear link between on- and offshore tectonic structures as well as the compressional regime at the easternmost flank edge, indicate a continental margin gravitational collapse as well as spreading to be present at Mt Etna. Moreover, we find evidence for the offshore southern boundary of the moving flank, which is identified as a right lateral oblique fault north of Catania Canyon. Our findings suggest a coupled volcano edifice/continental margin instability at Mt Etna, demonstrating first order linkage between on- and offshore tectonic processes.

Timing and Magnitude of Upper Crustal Shortening in the Gonghe Basin Region of the Northeastern Tibetan Plateau

NASA Astrophysics Data System (ADS)

Craddock, W. H.; Kirby, E.; Harkins, N.; Zhang, H.

2008-12-01

Characterizing the space-time patterns of the growth of high topography in Asia is an important step toward a deeper understanding of the mechanics of intracontinental deformation and its influence on global climate. In northeastern Tibet, there is emerging evidence that a number of ranges around the margins of the plateau experienced a pulse of deformation in the Late Miocene (ca. 12-8 Ma). It remains uncertain, however, whether this event was confined to the margins of the plateau, or whether interior regions deformed synchronously. Here we present a preliminary assessment of the timing and magnitude of upper crustal shortening along the margins of the Gonghe-Tongde basin complex. The Gonghe basin is located at the boundary between the high plateau of central Tibet and the southern flank of the Qilian Shan, and as such it is well-suited as a site to begin reconstructing patterns of plateau growth. The basin is overthrust by two regionally-extensive fault systems, the Qinghai Nan Shan (QNS) fault system on the north side and the Gonghe Nan Shan (GNS) fault system on the south side. Both fault systems are associated with deformation of Tertiary strata; variations in dip, sedimentary facies, and provenance are used to interpret the onset of growth along the margins of the Gonghe basin. A combination of the architecture of pre- and syntectonic basin strata, field measurements of fault dip, fault plane solutions, and topographic analysis of fold backlimbs for the GNS and QNS leads us to infer that the fault systems are a) trishear fault propagation style thrust faults and b) south vergent, with ~30 degree fault ramps soleing into a gently dipping decollement. Reconstructions of fold evolution suggest that the area has experienced > 5 km of upper crustal shortening in the late Cenozoic. A combination of magnetostratigraphy, biostratigraphy and cosmogenic burial ages provides preliminary age control. South of the GNS, a 250 m thick package of growth related strata are found to be 3.4 - 0.5 Ma. A 500 m thick exposure of growth strata on the north side of the range is also interpreted to be Plio-Quaternary in age. At present, however, we can only place a minimum bound on the onset of deformation of ca. 4-5 Ma. In light of a companion study interpreting the onset of deformation along the QNS at >= 5-7 Ma (Zhang H., in review), deformation of the Gonghe region appears to be slightly more recent than at the plateau margins. Historic seismicity and deformation of late-Quaternary alluvial surfaces on both fault systems indicate that these structures have remained active into the Pleistocene.

The impact of splay faults on fluid flow, solute transport, and pore pressure distribution in subduction zones: A case study offshore the Nicoya Peninsula, Costa Rica

NASA Astrophysics Data System (ADS)

Lauer, Rachel M.; Saffer, Demian M.

2015-04-01

Observations of seafloor seeps on the continental slope of many subduction zones illustrate that splay faults represent a primary hydraulic connection to the plate boundary at depth, carry deeply sourced fluids to the seafloor, and are in some cases associated with mud volcanoes. However, the role of these structures in forearc hydrogeology remains poorly quantified. We use a 2-D numerical model that simulates coupled fluid flow and solute transport driven by fluid sources from tectonically driven compaction and smectite transformation to investigate the effects of permeable splay faults on solute transport and pore pressure distribution. We focus on the Nicoya margin of Costa Rica as a case study, where previous modeling and field studies constrain flow rates, thermal structure, and margin geology. In our simulations, splay faults accommodate up to 33% of the total dewatering flux, primarily along faults that outcrop within 25 km of the trench. The distribution and fate of dehydration-derived fluids is strongly dependent on thermal structure, which determines the locus of smectite transformation. In simulations of a cold end-member margin, smectite transformation initiates 30 km from the trench, and 64% of the dehydration-derived fluids are intercepted by splay faults and carried to the middle and upper slope, rather than exiting at the trench. For a warm end-member, smectite transformation initiates 7 km from the trench, and the associated fluids are primarily transmitted to the trench via the décollement (50%), and faults intercept only 21% of these fluids. For a wide range of splay fault permeabilities, simulated fluid pressures are near lithostatic where the faults intersect overlying slope sediments, providing a viable mechanism for the formation of mud volcanoes.

Systematic assessment of fault stability in the Northern Niger Delta Basin, Nigeria: Implication for hydrocarbon prospects and increased seismicities

NASA Astrophysics Data System (ADS)

Adewole, E. O.; Healy, D.

2017-03-01

Accurate information on fault networks, the full stress tensor, and pore fluid pressures are required for quantifying the stability of structure-bound hydrocarbon prospects, carbon dioxide sequestration, and drilling prolific and safe wells, particularly fluid injections wells. Such information also provides essential data for a proper understanding of superinduced seismicities associated with areas of intensive hydrocarbon exploration and solid minerals mining activities. Pressure and stress data constrained from wells and seismic data in the Northern Niger Delta Basin (NNDB), Nigeria, have been analysed in the framework of fault stability indices by varying the maximum horizontal stress direction from 0° to 90°, evaluated at depths of 2 km, 3.5 km and 4 km. We have used fault dips and azimuths interpreted from high resolution 3D seismic data to calculate the predisposition of faults to failures in three faulting regimes (normal, pseudo-strike-slip and pseudo-thrust). The weighty decrease in the fault stability at 3.5 km depth from 1.2 MPa to 0.55 MPa demonstrates a reduction of the fault strength by high magnitude overpressures. Pore fluid pressures > 50 MPa have tendencies to increase the risk of faults to failure in the study area. Statistical analysis of stability indices (SI) indicates faults dipping 50°-60°, 80°-90°, and azimuths ranging 100°-110° are most favourably oriented for failure to take place, and thus likely to favour migrations of fluids given appropriate pressure and stress conditions in the dominant normal faulting regime of the NNDB. A few of the locally assessed stability of faults show varying results across faulting regimes. However, the near similarities of some model-based results in the faulting regimes explain the stability of subsurface structures are greatly influenced by the maximum horizontal stress (SHmax) direction and magnitude of pore fluid pressures.

Moroccan crustal response to continental drift.

PubMed

Kanes, W H; Saadi, M; Ehrlich, E; Alem, A

1973-06-01

The formation and development of a zone of spreading beneath the continental crust resulted in the breakup of Pangea and formation of the Atlantic Ocean. The crust of Morocco bears an extremely complete record of the crustal response to this episode of mantle dynamics. Structural and related depositional patterns indicate that the African margin had stabilized by the Middle Jurassic as a marine carbonate environment; that it was dominated by tensile stresses in the early Mesozoic, resulting in two fault systems paralleling the Atlantic and Mediterranean margins and a basin and range structural-depositional style; and that it was affected by late Paleozoic metamorphism and intrusion. Mesozoic events record the latter portion of African involvement in the spreading episode; late Paleozoic thermal orogenesis might reflect the earlier events in the initiation of the spreading center and its development beneath significant continental crust. In that case, more than 100 million years were required for mantle dynamics to break up Pangea.

Formation and evolution of magma-poor margins, an example of the West Iberia margin

NASA Astrophysics Data System (ADS)

Perez-Gussinye, Marta; Andres-Martinez, Miguel; Morgan, Jason P.; Ranero, Cesar R.; Reston, Tim

2016-04-01

The West Iberia-Newfoundland (WIM-NF) conjugate margins have been geophysically and geologically surveyed for the last 30 years and have arguably become a paradigm for magma-poor extensional margins. Here we present a coherent picture of the WIM-NF rift to drift evolution that emerges from these observations and numerical modeling, and point out important differences that may exist with other magma-poor margins world-wide. The WIM-NF is characterized by a continental crust that thins asymmetrically and a wide and symmetric continent-ocean transition (COT) interpreted to consist of exhumed and serpentinised mantle with magmatic products increasing oceanward. The architectural evolution of these margins is mainly dominated by cooling under very slow extension velocities (<~6 mm/yr half-rate) and a lower crust that most probably was not extremely weak at the start of rifting. These conditions lead to a system where initially deformation is distributed over a broad area and the upper, lower crust and lithosphere are decoupled. As extension progresses upper, lower, crust and mantle become tightly coupled and deformation localizes due to strengthening and cooling during rifting. Coupling leads to asymmetric asthenospheric uplift and weakening of the hanginwall of the active fault, where a new fault forms. This continued process leads to the formation of an array of sequential faults that dip and become younger oceanward. Here we show that these processes acting in concert: 1) reproduce the margin asymmetry observed at the WIM-NF, 2) explain the fault geometry evolution from planar, to listric to detachment like by having one common Andersonian framework, 3) lead to the symmetric exhumation of mantle with little magmatism, and 4) explain the younging of the syn-rift towards the basin centre and imply that unconformities separating syn- and post-rift may be diachronous and younger towards the ocean. Finally, we show that different lower crustal rheologies lead to different patterns of extension and to an abrupt transition to oceanic crust, even at magma-poor margins.

The Seismicity of Two Hyperextended Margins

NASA Astrophysics Data System (ADS)

Redfield, Tim; Terje Osmundsen, Per

2013-04-01

A seismic belt marks the outermost edge of Scandinavia's proximal margin, inboard of and roughly parallel to the Taper Break. A similar near- to onshore seismic belt runs along its inner edge, roughly parallel to and outboard of the asymmetric, seaward-facing escarpment. The belts converge at both the northern and southern ends of Scandinavia, where crustal taper is sharp and the proximal margin is narrow. Very few seismic events have been recorded on the intervening, gently-tapering Trøndelag Platform. Norway's distribution of seismicity is systematically ordered with respect to 1) the structural templates of high-beta extension that shaped the thinning gradient during Late Jurassic or Early Cretaceous time, and 2) the topographically resurgent Cretaceous-Cenozoic "accommodation phase" family of escarpments that approximate the innermost limit of crustal thinning [See Redfield and Osmundsen (2012) for diagrams, definitions, discussion, and supporting citations.] Landwards from the belt of earthquake epicenters that mark the Taper Break the crust consistently thickens, and large fault arrays tend to sole out at mid crustal levels. Towards the sea the crystalline continental crust is hyperextended, pervasively faulted, and generally very thin. Also, faulting and serpentinization may have affected the uppermost parts of the distal margin's lithospheric mantle. Such contrasting structural conditions may generate a contrasting stiffness: for a given stress, more strain can be accommodated in the distal margin than in the less faulted proximal margin. By way of comparison, inboard of the Taper Break on the gently-tapered Trøndelag Platform, faulting was not penetrative. There, similar structural conditions prevail and proximal margin seismicity is negligible. Because stress concentration can occur where material properties undergo significant contrast, the necking zone may constitute a natural localization point for post-thinning phase earthquakes. In Scandinavia, loads generated by escarpment erosion, offshore sedimentary deposition, and post-glacial rebound have been periodically superimposed throughout the Neogene. Their vertical stress patterns are mutually-reinforcing during deglaciation. However, compared to the post-glacial dome the pattern of maximum uplift/unloading generated by escarpment erosion will be longer, more linear, and located atop the emergent proximal margin. The pattern of offshore maximum deposition/loading will be similar. This may help explain the asymmetric expenditure of Fennoscandia's annual seismic energy budget. It may also help explain the obvious Conundrum: if stress generated by erosion and deposition is sufficiently great, fault reactivation and consequent seismicity can occur at any hyperextended passive margin sector regardless of its glacial history. Onshore Scandinavia, episodic footwall uplift and escarpment rejuvenation may have been driven by just such a mechanism throughout much of the later Cretaceous and Cenozoic. SE Brasil offers a glimpse of how Norway's hyperextended margin might manifest itself seismically in the absence of post-glacial rebound. Compilations suggest two seismic belts may exist. One, offshore, follows the thinned crust of the ultra-deep, hyperextended Campos and Santos basins. Onshore, earthquakes occur more commonly in the elevated highlands of the escarpments, and track especially the long, linear ranges such as the Serra de Mantiquiera and Serra do Espinhaço. Seismicity is more rare in the coastal lowlands, and largely absent in the Brasilian hinterland. Although never glaciated since the time of hyperextension and characterized by significantly fewer earthquakes in toto, SE Brasil's pattern of seismicity closely mimics Scandinavia. Commencing after perhaps just a few tens of millions of years of 'sag' basin infill, accommodation phase fault reactivation and footwall uplift at passive margins is the inexorable product of hyperextension. CITATIONS Redfield, T.F. and P.T. Osmundsen, 2012, GSA Bulletin, doi: 10.1130/B30691.1

Feature extraction based on semi-supervised kernel Marginal Fisher analysis and its application in bearing fault diagnosis

NASA Astrophysics Data System (ADS)

Jiang, Li; Xuan, Jianping; Shi, Tielin

2013-12-01

Generally, the vibration signals of faulty machinery are non-stationary and nonlinear under complicated operating conditions. Therefore, it is a big challenge for machinery fault diagnosis to extract optimal features for improving classification accuracy. This paper proposes semi-supervised kernel Marginal Fisher analysis (SSKMFA) for feature extraction, which can discover the intrinsic manifold structure of dataset, and simultaneously consider the intra-class compactness and the inter-class separability. Based on SSKMFA, a novel approach to fault diagnosis is put forward and applied to fault recognition of rolling bearings. SSKMFA directly extracts the low-dimensional characteristics from the raw high-dimensional vibration signals, by exploiting the inherent manifold structure of both labeled and unlabeled samples. Subsequently, the optimal low-dimensional features are fed into the simplest K-nearest neighbor (KNN) classifier to recognize different fault categories and severities of bearings. The experimental results demonstrate that the proposed approach improves the fault recognition performance and outperforms the other four feature extraction methods.

The Mentawai forearc sliver off Sumatra: A model for a strike-slip duplex at a regional scale

NASA Astrophysics Data System (ADS)

Berglar, Kai; Gaedicke, Christoph; Ladage, Stefan; Thöle, Hauke

2017-07-01

At the Sumatran oblique convergent margin the Mentawai Fault and Sumatran Fault zones accommodate most of the trench parallel component of strain. These faults bound the Mentawai forearc sliver that extends from the Sunda Strait to the Nicobar Islands. Based on multi-channel reflection seismic data, swath bathymetry and high resolution sub-bottom profiling we identified a set of wrench faults obliquely connecting the two major fault zones. These wrench faults separate at least four horses of a regional strike-slip duplex forming the forearc sliver. Each horse comprises an individual basin of the forearc with differing subsidence and sedimentary history. Duplex formation started in Mid/Late Miocene southwest of the Sunda Strait. Initiation of new horses propagated northwards along the Sumatran margin over 2000 km until Early Pliocene. These results directly link strike-slip tectonics to forearc evolution and may serve as a model for basin evolution in other oblique subduction settings.

How the gas hydrate system gives insight into subduction wedge dewatering processes in a zone of highly-oblique convergence on the southern Hikurangi margin of New Zealand

NASA Astrophysics Data System (ADS)

Crutchley, Gareth; Klaeschen, Dirk; Pecher, Ingo; Henrys, Stuart

2017-04-01

The southern end of New Zealand's Hikurangi subduction margin is characterised by highly-oblique convergence as it makes a southward transition into a right-lateral transform plate boundary at the Alpine Fault. Long-offset seismic data that cross part of the offshore portion of this transition zone give new insight into the nature of the plate boundary. We have carried out 2D pre-stack depth migrations, with an iterative reflection tomography to update the velocity field, on two seismic lines in this area to investigate fluid flow processes that have implications for the mechanical stability of the subduction interface. The results show distinct and focused fluid expulsion pathways from the subduction interface to the shallow sub-surface. For example, on one of the seismic lines there is a clear disruption of the gas hydrate system at its intersection with a splay fault - a clear indication of focused fluid release from the subduction interface. The seismic velocities derived from tomography also highlight a broad, pronounced low velocity zone beneath the deforming wedge that we interpret as a thick zone of gas-charged fluids that may have important implications for the long-term frictional stability of the plate boundary in this area. The focused flow upward toward the seafloor has the potential to result in the formation of concentrated gas hydrate deposits. Our on-going work on these data will include amplitude versus offset analysis in an attempt to better characterise the nature of the subduction interface, the fluids in that region, and also the shallower gas hydrate system.

Back-arc basin opening and closure along the southern margin of the Sea of Japan

NASA Astrophysics Data System (ADS)

Sato, Hiroshi; Claringbould, Johan; Ishiyama, Tatsuya; Kato, Naoko; Abe, Susumu; Kawasaki, Shinji

2016-04-01

Following the tsunami disaster produced by 2001 Off-Tohoku earthquake (M9) along the Pacific coast of Japan, the Japanese government started an intense evaluation of tsunami hazards. This evaluation spanned along the full Japanese coast, including the Sea of Japan coast on the western side of the Japan arc. In the Sea of Japan, tsunamis are produced by crustal faults. As the longer interval of faulting activity, the historical records of tsunamis in the Sea of Japan are not enough for the evaluation of tsunami height. Thus, the evaluation is carried out based on structural analyses of the margin of the Sea of Japan. To get better understanding of the present-day structural geometry and develop a source-fault model in this region, intense seismic reflection profiling has been carried out since 2013. We introduce the results of the seismic reflection profiles and discuss the structural evolution of the southern margin of the Sea of Japan. 2D seismic reflection profiles were acquired using 1950 cu. in. air-gun and 2100 m streamer cable. The seismic profiles provide the image image up to 3 seconds TWT. The southern margin of the Sea of Japan was produced by back-arc opening and post-rift deformation, and the structural evolution of this area is divided into several stages: rifting (25 - 14 Ma), post-rift compression (14 - 5 Ma), weak thrusting (5 - 1 Ma), and strike-slip deformation (1 Ma to present). During the rifting stage that is associated with the fan-shaped opening of the Sea of Japan, grabens and half-grabens were formed trending parallel to the extension of SW-Japan arc. These grabens were filled by syn-rift sediments, and the maximum thickness of basin fill is observed along the southern margin of the rifted crust. The opening of the Sea of Japan ceased as a result of the collision of Izu-Bonin-Mariana arc system at the Izu collision zone on the central part of Honshu, Japan. Soon after the this event, the young Shikoku basin within the Philippine Sea plate (PHS) moved northward towards the Nankai trough on the southeastern side of the SW-Japan arc. Due to the high thermal regime of the Shikoku basin, the resistance along the Nankai trough was so large that shortening deformation occurred along in the failed marginal rift zone that was developed previously along the southern margin of the Sea of Japan. This resulted in the Shinji fold belt. After the start of the subduction of the Shikoku basin along the Nankai trough, the rate of shortening in the Shinji fold belt was decreased and the folded strata were covered by sub-horizontal Pliocene sediments. Reverse faulting of the arc-parallel faults from Pliocene to early Pleistocene along the small number of faults suggests that the compression from the Nankai trough still has been continued in this stage. A change in the direction of the motion of PHS at 1 Ma produced major change in stress regime from NS compression to EW compression in the back-arc. Following the change of stress regime, the former reverse faults reactivated as strike-slip faults. The structural evolution and inherited structure presented here provide essential information for constructing the tsunami source-fault model along southern margin of the Sea of Japan.

A possible transoceanic tsunami directed toward the U.S. west coast from the Semidi segment, Alaska convergent margin

USGS Publications Warehouse

von Huene, Roland E.; Miller, John J.; Dartnell, Peter

2016-01-01

The Semidi segment of the Alaska convergent margin appears capable of generating a giant tsunami like the one produced along the nearby Unimak segment in 1946. Reprocessed legacy seismic reflection data and a compilation of multibeam bathymetric surveys reveal structures that could generate such a tsunami. A 200 km long ridge or escarpment with crests >1 km high is the surface expression of an active out-of-sequence fault zone, recently referred to as a splay fault. Such faults are potentially tsunamigenic. This type of fault zone separates the relatively rigid rock of the margin framework from the anelastic accreted sediment prism. Seafloor relief of the ridge exceeds that of similar age accretionary prism ridges indicating preferential slip along the splay fault zone. The greater slip may derive from Quaternary subduction of the Patton Murray hot spot ridge that extends 200 km toward the east across the north Pacific. Estimates of tsunami repeat times from paleotsunami studies indicate that the Semidi segment could be near the end of its current inter-seismic cycle. GPS records from Chirikof Island at the shelf edge indicate 90% locking of plate interface faults. An earthquake in the shallow Semidi subduction zone could generate a tsunami that will inundate the US west coast more than the 1946 and 1964 earthquakes because the Semidi continental slope azimuth directs a tsunami southeastward.

High-resolution multi-channel seismic images of the Queen Charlotte Fault system offshore southeastern Alaska

NASA Astrophysics Data System (ADS)

Miller, N. C.; Brothers, D. S.; Kluesner, J.; Balster-Gee, A.; Ten Brink, U. S.; Andrews, B. D.; Haeussler, P. J.; Watt, J. T.; Dartnell, P.; East, A. E.

2016-12-01

We present high-resolution multi-channel seismic (MCS) images of fault structure and sedimentary stratigraphy along the southeastern Alaska margin, where the northern Queen Charlotte Fault (QCF) cuts the shelf-edge and slope. The QCF is a dominantly strike slip system that forms the boundary between the Pacific (PA) and North American (NA) plates offshore western Canada and southeastern Alaska. The data were collected using a 64 channel, 200 m digital streamer and a 0.75-3 kJ sparker source aboard the R/V Norseman in August 2016. The survey was designed to cross a seafloor fault trace recently imaged by multibeam sonar (see adjacent poster by Brothers et al.) and to extend the subsurface information landward and seaward from the fault. Analysis of these MCS and multibeam data focus on addressing key questions that have significant implications for the kinematic and geodynamic history of the fault, including: Is the imaged surface fault in multibeam sonar the only recently-active fault trace? What is the shallow fault zone width and structure, is the internal structure of the recently-discovered pull-apart basin a dynamically developing structure? How does sediment thickness vary along the margin and how does this variation affect the fault expression? Can previous glacial sequences be identified in the stratigraphy?

A Hybrid Stochastic-Neuro-Fuzzy Model-Based System for In-Flight Gas Turbine Engine Diagnostics

DTIC Science & Technology

2001-04-05

Margin (ADM) and (ii) Fault Detection Margin (FDM). Key Words: ANFIS, Engine Health Monitoring , Gas Path Analysis, and Stochastic Analysis Adaptive Network...The paper illustrates the application of a hybrid Stochastic- Fuzzy -Inference Model-Based System (StoFIS) to fault diagnostics and prognostics for both...operational history monitored on-line by the engine health management (EHM) system. To capture the complex functional relationships between different

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mascle, J.; Blarez, E.

The authors present a marine study of the eastern Ivory Coast-Ghana continental margins which they consider one of the most spectacular extinct transform margins. This margin has been created during Early-Lower Cretaceous time and has not been submitted to any major geodynamic reactivation since its fabric. Based on this example, they propose to consider during the evolution of the transform margin four main and successive stages. Shearing contact is first active between two probably thick continental crusts and then between progressively thinning continental crusts. This leads to the creation of specific geological structures such as pull-apart graben, elongated fault lineaments,more » major fault scarps, shear folds, and marginal ridges. After the final continental breakup, a hot center (the mid-oceanic ridge axis) is progressively drifting along the newly created margin. The contact between two lithospheres of different nature should necessarily induce, by thermal exchanges, vertical crustal readjustments. Finally, the transform margin remains directly adjacent to a hot but cooling oceanic lithosphere; its subsidence behavior should then progressively be comparable to the thermal subsidence of classic rifted margins.« less

Geophysical evidence for a transform margin offshore Western Algeria: a witness of a subduction-transform edge propagator?

NASA Astrophysics Data System (ADS)

Badji, Rabia; Charvis, Philippe; Bracene, Rabah; Galve, Audrey; Badsi, Madjid; Ribodetti, Alessandra; Benaissa, Zahia; Klingelhoefer, Frauke; Medaouri, Mourad; Beslier, Marie-Odile

2015-02-01

For the first time, a deep seismic data set acquired in the frame of the Algerian-French SPIRAL program provides new insights regarding the origin of the westernmost Algerian margin and basin. We performed a tomographic inversion of traveltimes along a 100-km-long wide-angle seismic profile shot over 40 ocean bottom seismometers offshore Mostaganem (Northwestern Algeria). The resulting velocity model and multichannel seismic reflection profiles show a thin (3-4 km thick) oceanic crust. The narrow ocean-continent transition (less than 10 km wide) is bounded by vertical faults and surmounted by a narrow almost continuous basin filled with Miocene to Quaternary sediments. This fault system, as well as the faults organized in a negative-flower structure on the continent side, marks a major strike-slip fault system. The extremely sharp variation of the Moho depth (up to 45 ± 3°) beneath the continental border underscores the absence of continental extension in this area. All these features support the hypothesis that this part of the margin from Oran to Tenes, trending N65-N70°E, is a fossil subduction-transform edge propagator fault, vestige of the propagation of the edge of the Gibraltar subduction zone during the westward migration of the Alborán domain.

Along-Strike Variation in Geometry and Kinematics of a Major, Active Intracontinental Thrust System: the Pred-Terskey Fault Zone, Kyrgyz Tien Shan, Central Asia

NASA Astrophysics Data System (ADS)

Burgette, R. J.; Weldon, R. J.; Abdrakhmatov, K. Y.; Ormukov, C.

2004-12-01

The Pred-Terskey fault zone defines the southern margin of the Issyk-Kul basin, extending eastward over 250 km from at least the Chu River to the Kazakhstan border, and appears to be one of the most active zones in the Kyrgyz Tien Shan. Despite a diversity of structural styles and changes of vergence at the surface, the lateral continuity and overall geometry of the zone is consistent with a single north vergent thrust at depth, which uplifts the Terskey Range and generally tilts the south margin of the basin to the north. This northward tilting of the margin is probably due to a flattening of the fault as it approaches the surface. In spite of historical quiescence, it is likely capable of producing great earthquakes. We have conducted detailed field mapping coupled with terrace profiling and dating at seven representative, well-exposed areas of the fault zone. Based on these field observations and satellite image and air photo interpretation along the entire zone, we identify three major divisions in structural style expressed at the surface. The western segment is typified by the Tura-Su, Ak-Terek and Ton areas. A series of left-stepping, south-vergent, basement-involved reverse faults and folds are uplifting the southern margin of the Issyk-Kul basin in this area. The resulting uphill-facing scarps have trapped and diverted many of the rivers flowing north from the Terskey Range. Tertiary strata and Quaternary geomorphic surfaces show consistent, progressive northward tilting across the entire zone. The west-central segment is represented by the Kajy-Say area. South-vergent reverse faults and a north-vergent backthrust have uplifted an arcuate granite block. Offshore of this area, the lake floor descends to a sharp break in slope with a low relief area at a depth of about 650 m. Late Quaternary geomorphic features do not show evidence of tilting. In contrast to the areas east and west, the major north-dipping thrust is likely planar over this segment and daylights at the lake floor break in slope. The east-central segment is exemplified by the Barskaun and Jety Oguz areas. A high angle reverse fault juxtaposes Paleozoic rock against Tertiary sediments. To the north, a thrust fault with a sinuous trace places north-dipping Tertiary rock over the nearly horizontal basin floor. Quaternary terraces in the hanging wall of this fault record progressive northward tilting. North of the thrust fault a series of anticlines are growing out of the basin sediments. The eastern segment, which includes the Jergalan River valley, lacks a low angle thrust fault at the basin margin. Along this segment, the basement reverse fault uplifts Paleozoic rock against Quaternary basin sediment. To the north of this range-bounding structure, late Quaternary terraces are offset by south-vergent scarps. We are calculating geologic slip rates for each of the seven sites along the Pred-Terskey zone by dating terraces and constructing structural models consistent with both the rock and terrace records. Based on preliminary radiocarbon dates, a prominent Jety Oguz River terrace is 50 +/- 10 ka. The terrace is tilted 0.5° relative to the modern river, and with the low angle fault branching off of the basement reverse fault at dips ranging between 45° and 90° , the slip rate of this fault is 6 +/- 4 mm/yr. This is consistent with the GPS shortening rate across the Pred-Terskey zone at this longitude.

Active simultaneous uplift and margin-normal extension in a forearc high, Crete, Greece

NASA Astrophysics Data System (ADS)

Gallen, S. F.; Wegmann, K. W.; Bohnenstiehl, D. R.; Pazzaglia, F. J.; Brandon, M. T.; Fassoulas, C.

2014-07-01

The island of Crete occupies a forearc high in the central Hellenic subduction zone and is characterized by sustained exhumation, surface uplift and extension. The processes governing orogenesis and topographic development here remain poorly understood. Dramatic topographic relief (2-6 km) astride the southern coastline of Crete is associated with large margin-parallel faults responsible for deep bathymetric depressions known as the Hellenic troughs. These structures have been interpreted as both active and inactive with either contractional, strike-slip, or extensional movement histories. Distinguishing between these different structural styles and kinematic histories here allows us to explore more general models for improving our global understanding of the tectonic and geodynamic processes of syn-convergent extension. We present new observations from the south-central coastline of Crete that clarifies the role of these faults in the late Cenozoic evolution of the central Hellenic margin and the processes controlling Quaternary surface uplift. Pleistocene marine terraces are used in conjunction with optically stimulated luminesce dating and correlation to the Quaternary eustatic curve to document coastal uplift and identify active faults. Two south-dipping normal faults are observed, which extend offshore, offset these marine terrace deposits and indicate active N-S (margin-normal) extension. Further, marine terraces preserved in the footwall and hanging wall of both faults demonstrate that regional net uplift of Crete is occurring despite active extension. Field mapping and geometric reconstructions of an active onshore normal fault reveal that the subaqueous range-front fault of south-central Crete is synthetic to the south-dipping normal faults on shore. These findings are inconsistent with models of active horizontal shortening in the upper crust of the Hellenic forearc. Rather, they are consistent with topographic growth of the forearc in a viscous orogenic wedge, where crustal thickening and uplift are a result of basal underplating of material that is accompanied by extension in the upper portions of the wedge. Within this framework a new conceptual model is presented for the late Cenozoic vertical tectonics of the Hellenic forearc.

Extensive Gravity Sliding of Late Jurassic-Cretaceous Age along the Northern Yucatan Margin of the Gulf of Mexico

NASA Astrophysics Data System (ADS)

Steier, A.; Mann, P.

2017-12-01

Gravity slides on salt or shale detachment surfaces linking updip extension with down dip compression have been described from several margins of the Gulf of Mexico (GOM). In a region 250 km offshore from the southwestern coast of Florida, the late Jurassic section near Destin Dome and Desoto Canyon has undergone late Jurassic to Cretaceous gravity sliding and downdip dispersion of rigid blocks along the top of the underlying Louann salt. Yet there has been no previous study of similar structural styles on the slope and deep basin of its late Jurassic conjugate margin located 200 km offshore of the northern margin of the Yucatan Peninsula. This study describes an extensive area of Mesozoic gravity sliding from the northern Yucatan slope using a grid of 2D seismic data covering a 134,000 km2 area of the northern Yucatan margin tied to nine wells. These data allow the northern Yucatan margin to be divided into three slope and basinal provinces: 1) a 225 km length of the northeastern margin consisting of late Jurassic-Cretaceous section that is not underlain by salt, exhibits no gravity sliding features, and has sub-horizontal dips; 2) a 120 km length of the north-central Yucatan margin with gravity slide features characterized by an 80-km-wide updip zone of normal faults occupying the shelf edge and upper slope and a 50-km-wide downdip zone of folds and thrust faults at the base of the slope; the slide area exhibits multiple detached slide blocks composed of late Jurassic sandstones and marine mudstones separated by intervening salt rollers; growth wedges adjacent to listric, normal faults suggest a gradual and long-lived downdip motion of rigid fault blocks throughout much of the late Jurassic and Cretaceous rather than a catastrophic and instantaneous collapse of the shelf edge; the basal, normal detachment fault averages 3° in dip and is overlain by salt that varies from 0-500 ms in time thickness; by the end of the Cretaceous, most gravity sliding and vertical salt movement off the north-central Yucatan had ceased and was capped by the post-sliding Cretaceous-Paleocene boundary deposit (KPBD); and 3) a 150 km length of the southwestern margin with the largest thicknesses of salt; smaller salt rollers are less common as large diapirs are frequent and extensively deform the late Mesozoic section as well as overlying younger strata.

The Evergreen basin and the role of the Silver Creek fault in the San Andreas fault system, San Francisco Bay region, California

USGS Publications Warehouse

Jachens, Robert C.; Wentworth, Carl M.; Graymer, Russell W.; Williams, Robert; Ponce, David A.; Mankinen, Edward A.; Stephenson, William J.; Langenheim, Victoria

2017-01-01

The Evergreen basin is a 40-km-long, 8-km-wide Cenozoic sedimentary basin that lies mostly concealed beneath the northeastern margin of the Santa Clara Valley near the south end of San Francisco Bay (California, USA). The basin is bounded on the northeast by the strike-slip Hayward fault and an approximately parallel subsurface fault that is structurally overlain by a set of west-verging reverse-oblique faults which form the present-day southeastward extension of the Hayward fault. It is bounded on the southwest by the Silver Creek fault, a largely dormant or abandoned fault that splays from the active southern Calaveras fault. We propose that the Evergreen basin formed as a strike-slip pull-apart basin in the right step from the Silver Creek fault to the Hayward fault during a time when the Silver Creek fault served as a segment of the main route by which slip was transferred from the central California San Andreas fault to the Hayward and other East Bay faults. The dimensions and shape of the Evergreen basin, together with palinspastic reconstructions of geologic and geophysical features surrounding it, suggest that during its lifetime, the Silver Creek fault transferred a significant portion of the ∼100 km of total offset accommodated by the Hayward fault, and of the 175 km of total San Andreas system offset thought to have been accommodated by the entire East Bay fault system. As shown previously, at ca. 1.5–2.5 Ma the Hayward-Calaveras connection changed from a right-step, releasing regime to a left-step, restraining regime, with the consequent effective abandonment of the Silver Creek fault. This reorganization was, perhaps, preceded by development of the previously proposed basin-bisecting Mount Misery fault, a fault that directly linked the southern end of the Hayward fault with the southern Calaveras fault during extinction of pull-apart activity. Historic seismicity indicates that slip below a depth of 5 km is mostly transferred from the Calaveras fault to the Hayward fault across the Mission seismic trend northeast of the Evergreen basin, whereas slip above a depth of 5 km is transferred through a complex zone of oblique-reverse faults along and over the northeast basin margin. However, a prominent groundwater flow barrier and related land-subsidence discontinuity coincident with the concealed Silver Creek fault, a discontinuity in the pattern of seismicity on the Calaveras fault at the Silver Creek fault intersection, and a structural sag indicative of a negative flower structure in Quaternary sediments along the southwest basin margin indicate that the Silver Creek fault has had minor ongoing slip over the past few hundred thousand years. Two earthquakes with ∼M6 occurred in A.D. 1903 in the vicinity of the Silver Creek fault, but the available information is not sufficient to reliably identify them as Silver Creek fault events.

Faulting along the southern margin of Reelfoot Lake, Tennessee

USGS Publications Warehouse

Van Arsdale, R.; Purser, J.; Stephenson, W.; Odum, J.

1998-01-01

The Reelfoot Lake basin, Tennessee, is structurally complex and of great interest seismologically because it is located at the junction of two seismicity trends of the New Madrid seismic zone. To better understand the structure at this location, a 7.5-km-long seismic reflection profile was acquired on roads along the southern margin of Reelfoot Lake. The seismic line reveals a westerly dipping basin bounded on the west by the Reelfoot reverse fault zone, the Ridgely right-lateral transpressive fault zone on the east, and the Cottonwood Grove right-lateral strike-slip fault in the middle of the basin. The displacement history of the Reelfoot fault zone appears to be the same as the Ridgely fault zone, thus suggesting that movement on these fault zones has been synchronous, perhaps since the Cretaceous. Since the Reelfoot and Ridgely fault systems are believed responsible for two of the mainshocks of 1811-1812, the fault history revealed in the Reelfoot Lake profile suggests that multiple mainshocks may be typical of the New Madrid seismic zone. The Ridgely fault zone consists of two northeast-striking faults that lie at the base of and within the Mississippi Valley bluff line. This fault zone has 15 m of post-Eocene, up-to-the-east displacement and appears to locally control the eastern limit of Mississippi River migration. The Cottonwood Grove fault zone passes through the center of the seismic line and has approximately 5 m up-to-the-east displacement. Correlation of the Cottonwood Grove fault with a possible fault scarp on the floor of Reelfoot Lake and the New Markham fault north of the lake suggests the Cottonwood Grove fault may change to a northerly strike at Reelfoot Lake, thereby linking the northeast-trending zones of seismicity in the New Madrid seismic zone.

Performance Evaluation Tests for Environmental Research (PETER): evaluation of 114 measures

NASA Technical Reports Server (NTRS)

Bittner, A. C. Jr; Carter, R. C.; Kennedy, R. S.; Harbeson, M. M.; Krause, M.

1986-01-01

The goal of the Performance Evaluation Tests for Environmental Research (PETER) Program was to identify a set of measures of human capabilities for use in the study of environmental and other time-course effects. 114 measures studied in the PETER Program were evaluated and categorized into four groups based upon task stability and task definition. The Recommended category contained 30 measures that clearly obtained total stabilization and had an acceptable level of reliability efficiency. The Acceptable-But-Redundant category contained 15 measures. The 37 measures in the Marginal category, which included an inordinate number of slope and other derived measures, usually had desirable features which were outweighed by faults. The 32 measures in the Unacceptable category had either differential instability or weak reliability efficiency. It is our opinion that the 30 measures in the Recommended category should be given first consideration for environmental research applications. Further, it is recommended that information pertaining to preexperimental practice requirements and stabilized reliabilities should be utilized in repeated-measures environmental studies.

Style of extensional tectonism during rifting, Red Sea and Gulf of Aden

USGS Publications Warehouse

Bohannon, R.G.

1989-01-01

Geologic and geophysical studies from the Arabian continental margin in the southern Red Sea and LANDSAT analysis of the northern Somalia margin in the Gulf of Aden suggest that the early continental rifts were long narrow features that formed by extension on closely spaced normal faults above moderate- to shallow-dipping detachments with break-away zones defining one rift flank and root zones under the opposing rift flank. The rift flanks presently form the opposing continental margins across each ocean basin. The detachment on the Arabian margin dips gently to the west, with a breakaway zone now eroded above the deeply dissected terrain of the Arabian escarpment. A model is proposed in which upper crustal breakup occurs on large detachment faults that have a distinct polarity. -from Author

Major Paleostress Field Differences on Complementary Margins of the South Atlantic

NASA Astrophysics Data System (ADS)

Salomon, E.; Koehn, D.; Passchier, C. W.; Hackspacher, P. C.; Glasmacher, P. A.

2013-12-01

We present a detailed study of paleostress fields of the Namibian and Brazilian passive continental margins of the South Atlantic to address a general debate on whether or not these complementary margins experienced similar tectonic histories (e.g. Cobbold et al., 2001; Al-Hajri et al., 2009; Japsen et al., 2012). In our study, we compare the NW of Namibia and the SE of Brazil with each other. These areas are largely covered by the flood basalts of the Paraná-Etendeka-Large Igneous Province overlying Neo-Proterozoic basement of the Pan-African orogeny. With an age of ~133 Ma the basalts were emplaced just before or during the onset of the South Atlantic opening and thus serve as a good time marker for rift- and post-rift-related tectonics. We studied mainly fault planes and associated striations within the flood basalts and compared the resulting stress patterns of both margins. Results reveal remarkable differences in the stress patterns for SE Brazil and NW Namibia. In NW Namibia, a WSW-ENE directed extensional stress field dominates and fits well with extension of the original continental rift and the passive margin. A second extensional stress field (σ3 SSW oriented) and a strike-slip system (σ1 NW oriented) appear only subdued. In contrast, the SE of Brazil is mainly characterized by two strike-slip systems (σ1 oriented SW and E, respectively) whereas an extensional stress field is almost non-existent. The strike-slip faulting of the Brazilian study area occur widespread across SE Brazil as they are also evident in other paleostress studies of the region and might thus be the result of far-field stresses. Margin-parallel faults are scarce, so it appears that rift-related extension was restricted to a narrower strip along the continent-ocean boundary, now lying offshore. In NW Namibia, the faults of the extensional stress regime run parallel to the sub-margin-parallel basement structure (i.e. shear zones and foliation) and hence indicate a reactivation of the Neo-Proterozoic basement during the Atlantic rifting. The stress fields of NW Namibia stand in contrast to observations in other parts of southern Africa, where also compression is evident. We relate these variations to a strong influence of the basement structure on younger faulting in southern Africa. Our results indicate that different mechanisms may have produced the present-day high topography on both sides of the Southern Atlantic, the Brazilian margin being under compression in a strike-slip regime whereas the Namibian margin mainly under margin perpendicular extension. References Al-Hajri, Y. et al., 2009. Geology, 37, 883-886. Cobbold, P. R. et al., 2001. AAPG Bull., 85, 1925-1944. Japsen, P. et al., 2012. Geol. Soc. Am. Bull., 124, 800-816.

An intelligent fault diagnosis method of rolling bearings based on regularized kernel Marginal Fisher analysis

NASA Astrophysics Data System (ADS)

Jiang, Li; Shi, Tielin; Xuan, Jianping

2012-05-01

Generally, the vibration signals of fault bearings are non-stationary and highly nonlinear under complicated operating conditions. Thus, it's a big challenge to extract optimal features for improving classification and simultaneously decreasing feature dimension. Kernel Marginal Fisher analysis (KMFA) is a novel supervised manifold learning algorithm for feature extraction and dimensionality reduction. In order to avoid the small sample size problem in KMFA, we propose regularized KMFA (RKMFA). A simple and efficient intelligent fault diagnosis method based on RKMFA is put forward and applied to fault recognition of rolling bearings. So as to directly excavate nonlinear features from the original high-dimensional vibration signals, RKMFA constructs two graphs describing the intra-class compactness and the inter-class separability, by combining traditional manifold learning algorithm with fisher criteria. Therefore, the optimal low-dimensional features are obtained for better classification and finally fed into the simplest K-nearest neighbor (KNN) classifier to recognize different fault categories of bearings. The experimental results demonstrate that the proposed approach improves the fault classification performance and outperforms the other conventional approaches.

Impact of sea-level rise on earthquake and landslide triggering offshore the Alentejo margin (SW Iberia)

NASA Astrophysics Data System (ADS)

Neves, M. C.; Roque, C.; Luttrell, K. M.; Vázquez, J. T.; Alonso, B.

2016-12-01

Earthquakes and submarine landslides are recurrent and widespread manifestations of fault activity offshore SW Iberia. The present work tests the effects of sea-level rise on offshore fault systems using Coulomb stress change calculations across the Alentejo margin. Large-scale faults capable of generating large earthquakes and tsunamis in the region, especially NE-SW trending thrusts and WNW-ESE trending dextral strike-slip faults imaged at basement depths, are either blocked or unaffected by flexural effects related to sea-level changes. Large-magnitude earthquakes occurring along these structures may, therefore, be less frequent during periods of sea-level rise. In contrast, sea-level rise promotes shallow fault ruptures within the sedimentary sequence along the continental slope and upper rise within distances of <100 km from the coast. The results suggest that the occurrence of continental slope failures may either increase (if triggered by shallow fault ruptures) or decrease (if triggered by deep fault ruptures) as a result of sea-level rise. Moreover, observations of slope failures affecting the area of the Sines contourite drift highlight the role of sediment properties as preconditioning factors in this region.

The giant Carlin gold province: A protracted interplay of orogenic, basinal, and hydrothermal processes above a lithospheric boundary

USGS Publications Warehouse

Emsbo, P.; Groves, D.I.; Hofstra, A.H.; Bierlein, F.P.

2006-01-01

Northern Nevada hosts the only province that contains multiple world-class Carlin-type gold deposits. The first-order control on the uniqueness of this province is its anomalous far back-arc tectonic setting over the rifted North American paleocontinental margin that separates Precambrian from Phanerozoic subcontinental lithospheric mantle. Globally, most other significant gold provinces form in volcanic arcs and accreted terranes proximal to convergent margins. In northern Nevada, periodic reactivation of basement faults along this margin focused and amplified subsequent geological events. Early basement faults localized Devonian synsedimentary extension and normal faulting. These controlled the geometry of the Devonian sedimentary basin architecture and focused the discharge of basinal brines that deposited syngenetic gold along the basin margins. Inversion of these basins and faults during subsequent contraction produced the complex elongate structural culminations that characterize the anomalous mineral deposit "trends." Subsequently, these features localized repeated episodes of shallow magmatic and hydrothermal activity that also deposited some gold. During a pulse of Eocene extension, these faults focused advection of Carlin-type fluids, which had the opportunity to leach gold from gold-enriched sequences and deposit it in reactive miogeoclinal host rocks below the hydrologic seal at the Roberts Mountain thrust contact. Hence, the vast endowment of the Carlin province resulted from the conjunction of spatially superposed events localized by long-lived basement structures in a highly anomalous tectonic setting, rather than by the sole operation of special magmatic or fluid-related processes. An important indicator of the longevity of this basement control is the superposition of different gold deposit types (e.g., Sedex, porphyry, Carlin-type, epithermal, and hot spring deposits) that formed repeatedly between the Devonian and Miocene time along the trends. Interestingly, the large Cretaceous Alaska-Yukon intrusion-related gold deposits (e.g., Fort Knox) are associated with the northern extension of the same lithospheric margin in the Selwyn basin, which experienced an analogous series of geologic events. ?? Springer-Verlag 2006.

Tectonics and Current Plate Motions of Northern Vancouver Island and the Adjacent Mainland

NASA Astrophysics Data System (ADS)

Jiang, Y.; Leonard, L. J.; Henton, J.; Hyndman, R. D.

2016-12-01

Northern Vancouver Island comprises a complex transition zone along the western margin of the North America plate, between the subducting Juan de Fuca plate to the south and the transcurrent Queen Charlotte Fault to the north off Haida Gwaii. The tectonic history and seismic potential for this region are unclear. Here we present current plate motions for northern Vancouver Island and the adjacent mainland, determined from continuous and campaign GPS measurements processed in a consistent manner. Immediately to the north of the mid-Vancouver Island Nootka Fault Zone, the northern limit of Juan de Fuca plate subduction, GPS velocity vectors show slower Explorer plate subduction than the Juan de Fuca Plate. Off northernmost Vancouver Island, the Winona Block is possibly converging at a slow rate that decreases northward to zero. We find a constant northward margin-parallel translation of up to 5 mm/year from northern Vancouver Island extending to Alaska. The southern limit of this translation coincides with areas of high heat flow that may reflect extension and the northern limit of episodic tremor and slip (ETS) on the Cascadia megathrust. The origin of the northward translation is poorly understood. We find a mainland coastal shear zone extends as far south as northern Vancouver Island where the offshore plate boundary is likely subduction. The pattern of the observed coastal shear cannot reflect interseismic locking on a major offshore transcurrent fault. The geodetically determined mainland coastal zone velocities decrease landward from 5 to 0 mm/yr across a region where no active faults have been identified and there is very little current seismicity. In Haida Gwaii, oblique convergence is apparent in the GPS data, consistent with partitioning between margin-parallel and margin-perpendicular strain. After removing the margin parallel translation from the data, we determine an average maximum locking depth of 15 km for the Queen Charlotte transcurrent fault, consistent with seismicity and seismic structure data.

Tectonic evolution of the Paranoá basin: New evidence from gravimetric and stratigraphic data

NASA Astrophysics Data System (ADS)

Martins-Ferreira, Marco Antonio Caçador; Campos, José Eloi Guimarães; Von Huelsen, Monica Giannoccaro

2018-06-01

Field gravimetric and stratigraphic surveys were conducted with the aim to constraint the mechanisms responsible for the initiation of the Stenian-Tonian Paranoá basin, central Brazil, a subject not yet studied in detail. The Paranoá Group crops out in the external zone of the Brasília Belt, a Neoproterozoic orogen in the western margin of the São Francisco Craton. Detailed geological mapping confirmed the existence of a regional scale fault that controlled sedimentation of the Paranoá Group during the deposition of its basal formations, revealing important details about basin initiation and early evolution. Gravimetric modeling indicates the existence of paleorift structures beneath the Paranoá sequence in the study area. Results from both stratigraphic and gravimetric surveys show strong evidence of mechanical subsidence by faulting during basin initiation. Unsorted, angular, clasts cut by quartz veins and brecciated boulders present in the basal conglomerate, support this hypothesis. Basin initiation faults coincide with deeper paleorift faults and are thus interpreted as reactivations of the older Statherian Araí Rift. The reactivations favored an initial regime of mechanical subsidence, dominated by the development of epirogenic arches subsiding at different rates. Apart from faulting activity, the post-basal sequence presents no evidence of rift environment in the strict sense. Besides, the great lateral continuity and relatively constant thickness of facies, indicate that an initial mechanic subsidence rapidly gave way to flexural subsidence during subsequent stages of basin evolution. The Paranoá Group do not present reliable characteristics that would allow its strict classification as a passive margin. Its main stratigraphic characteristics, tectonic location and basement architecture, indicate that the Paranoá Group was deposited in a cratonic margin basin, and may have been either connected to a passive margin basin at times of sea level rise, or evolved to a passive margin later in time.

Identifying active interplate and intraplate fault zones in the western Caribbean plate from seismic reflection data and the significance of the Pedro Bank fault zone in the tectonic history of the Nicaraguan Rise

NASA Astrophysics Data System (ADS)

Ott, B.; Mann, P.

2015-12-01

The offshore Nicaraguan Rise in the western Caribbean Sea is an approximately 500,000 km2 area of Precambrian to Late Cretaceous tectonic terranes that have been assembled during the Late Cretaceous formation of the Caribbean plate and include: 1) the Chortis block, a continental fragment; 2) the Great Arc of the Caribbean, a deformed Cretaceous arc, and 3) the Caribbean large igneous province formed in late Cretaceous time. Middle Eocene to Recent eastward motion of the Caribbean plate has been largely controlled by strike-slip faulting along the northern Caribbean plate boundary zone that bounds the northern margin of the Nicaraguan Rise. These faults reactivate older rift structures near the island of Jamaica and form the transtensional basins of the Honduran Borderlands near Honduras. Recent GPS studies suggest that small amount of intraplate motion within the current margin of error of GPS measurements (1-3 mm/yr) may occur within the center of the western Caribbean plate at the Pedro Bank fault zone and Hess Escarpment. This study uses a database of over 54,000 km of modern and vintage 2D seismic data, combined with earthquake data and results from previous GPS studies to define the active areas of inter- and intraplate fault zones in the western Caribbean. Intraplate deformation occurs along the 700-km-long Pedro Bank fault zone that traverses the center of the Nicaraguan Rise and reactivates the paleo suture zone between the Great Arc of the Caribbean and the Caribbean large igneous province. The Pedro Bank fault zone also drives active extension at the 200-km-long San Andres rift along the southwest margin of the Nicaraguan Rise. Influence of the Cocos Ridge indentor may be contributing to reactivation of faulting along the southwesternmost, active segment of the Hess Escarpment.

Normal Faulting at the Western Margin of the Altiplano Plateau, Southern Peru

NASA Astrophysics Data System (ADS)

Schildgen, T. F.; Hodges, K. V.; Whipple, K. X.; Perignon, M.; Smith, T. M.

2004-12-01

Although the western margin of the Altiplano Plateau is commonly used to illustrate the marked differences in the evolution of a mountain range with strong latitudinal and longitudinal precipitation gradients, the nature of tectonism in this semi-arid region is poorly understood and much debated. The western margin of the Altiplano in southern Peru and northern Chile marks an abrupt transition from the forearc region of the Andes to the high topography of the Cordillera Occidental. This transition has been interpreted by most workers as a monocline, with modifications due to thrust faulting, normal faulting, and gravity slides. Based on recent fieldwork and satellite image analysis, we suggest that, at least in the semi-arid climate of southern Peru, this transition has been the locus of significant high-angle normal faulting related to the block uplift of the Cordillera Occidental. We have focused our initial work in the vicinity of 15\\deg S latitude, 71\\deg W longitude, where the range front crosses Colca Canyon, a major antecedent drainage northwest of Arequipa. In that area, Oligocene to Miocene sediments of the Moquegua Formation, which were eroded from uplifted terrain to the northeast, presently dip to the northeast at angles between 2 and 10º. Field observations of a normal fault contact between the Moquegua sedimentary rocks and Jurassic basement rocks, as well as 15-m resolution 3-D images generated from ASTER satellite imagery, show that the Moquegua units are down-dropped to the west across a steeply SW-dipping normal fault of regional significance. Morphology of the range front throughout southern Peru suggests that normal faulting along the range front has characterized the recent tectonic history of the region. We present geochronological data to constrain the timing of movement both directly from the fault zone as well as indirectly from canyon incision that likely responded to fault movement.

Effects of Arabia-Eurasia Collision on Strike-slip Faults in Central Anatolia?

NASA Astrophysics Data System (ADS)

Whitney, D. L.; Lefebvre, C.; Thomson, S. N.; Idleman, L.; Cosca, M. A.; Kaymakci, N.; Teyssier, C. P.; Umhoefer, P. J.

2013-12-01

The North and East Anatolian faults accommodate much of the tectonic escape of Anatolia in response to Arabia-Eurasia collision and building of the Turkish-Iranian plateau, but these structures formed <10 m.y. ago, at least 25 m.y. after the onset of collision at ~35 Ma. Some of the major strike-slip fault zones located between the North and East Anatolian faults have had long and complex histories of displacement. These faults have deformed, and in some cases exhumed, metamorphic massifs located between fault strands. One example is the Nigde Massif, which was initially exhumed in the Late Cretaceous, then reburied and reheated, along with its overlying sedimentary basin, to a depth of ~10 km at 30 × 5 Ma. Final exhumation and cooling occurred by ~15-17 Ma (massif margin) to ~12 Ma (structurally deepest levels). This depth-temperature-time-deformation history is tracked by a combination of thermobarometric methods, structural and stratigraphic analysis, and geo/thermochronometry (U-Pb zircon, monazite; 40Ar/39Ar hornblende, muscovite, biotite, K-feldspar; zircon and apatite fission-track in metamorphic rocks and basin deposits; and apatite (U-Th)/He). Recent mapping shows the presence of at least two oblique-thrust slices; the structurally higher one accounts for the resetting of detrital apatite fission track and AHe ages in the basin rocks as well as metamorphic apatite near the margin of the massif. The structurally deeper one cuts through the metamorphic basement and explains why mineral lineations and metamorphic assemblages are different along the eastern margin relative to those in the core of the massif. Although the timing of displacement has not been dated directly, low-T thermochronology age and modeling results document a perturbation at ~30 Ma, consistent with the idea that the Ecemis Fault of the Central Anatolian Fault Zone, and probably other pre-existing strike-slip faults in central Anatolia, experienced Late Eocene-Oligocene displacement in response to Arabia-Eurasia collision to the south and SE.

Passive bookshelf faulting driven by gravitational spreading as the cause of the tiger-stripe-fracture formation and development in the South Polar Terrain of Enceladus

NASA Astrophysics Data System (ADS)

Yin, A.; Pappalardo, R. T.

2013-12-01

Detailed photogeologic mapping of the tiger-stripe fractures in the South Polar Terrain (SPT) of Enceladus indicates that these structures are left-slip faults and terminate at hook-shaped fold-thrust zones and/or Y-shaped horsetail splay-fault zones. The semi-square-shaped tectonic domain that hosts the tiger-stripe faults is bounded by right-slip and left-slip faults on the north and south edges and fold-thrust and extensional zones on the western and eastern edges. We explain the above observations by a passive bookshelf-faulting model in which individual tiger-stripe faults are bounded by deformable wall rocks accommodating distributed deformation. Based on topographic data, we suggest that gravitational spreading had caused the SPT to spread unevenly from west to east. This process was accommodated by right-slip and left-slip faulting on the north and south sides and thrusting and extension along the eastern and southern margins of the tiger-stripe tectonic domain. The uneven spreading, expressed by a gradual northward increase in the number of extensional faults and thrusts/folds along the western and eastern margins, was accommodated by distributed right-slip simple shear across the whole tiger-stripe tectonic domain. This mode of deformation in turn resulted in the development of a passive bookshelf-fault system characterized by left-slip faulting on individual tiger-stripe fractures.

Evidence of Quaternary and recent activity along the Kyaukkyan Fault, Myanmar

NASA Astrophysics Data System (ADS)

Crosetto, Silvia; Watkinson, Ian M.; Soe Min; Gori, Stefano; Falcucci, Emanuela; Nwai Le Ngal

2018-05-01

Cenozoic right-lateral shear between the eastern Indian margin and Eurasia is expressed by numerous N-S trending fault systems inboard of the Sunda trench, including the Sagaing Fault. The most easterly of these fault systems is the prominent ∼500 km long Kyaukkyan Fault, on the Shan Plateau. Myanmar's largest recorded earthquake, Mw 7.7 on 23rd May 1912, focused near Maymyo, has been attributed to the Kyaukkyan Fault, but the area has experienced little significant seismicity since then. Despite its demonstrated seismic potential and remarkable topographic expression, questions remain about the Kyaukkyan Fault's neotectonic history.

Active shortening of the Cascadia forearc and implications for seismic hazards of the Puget Lowland

USGS Publications Warehouse

Johnson, S.Y.; Blakely, R.J.; Stephenson, W.J.; Dadisman, S.V.; Fisher, M.A.

2004-01-01

Margin-parallel shortening of the Cascadia forearc is a consequence of oblique subduction of the Juan de Fuca plate beneath North America. Strike-slip, thrust, and oblique crustal faults beneath the densely populated Puget Lowland accommodate much of this north-south compression, resulting in large crustal earthquakes. To better understand this forearc deformation and improve earthquake hazard, assessment, we here use seismic reflection surveys, coastal exposures of Pleistocene strata, potential-field data, and airborne laser swath mapping to document and interpret a significant structural boundary near the City of Tacoma. This boundary is a complex structural zone characterized by two distinct segments. The northwest trending, eastern segment, extending from Tacoma to Carr Inlet, is formed by the broad (??? 11.5 km), southwest dipping (??? 11??-2??) Rosedale monocline. This monocline raises Crescent Formation basement about 2.5 km, resulting in a moderate gravity gradient. We interpret the Rosedale monocline as a fault-bend fold, forming above a deep thrust fault. Within the Rosedale monocline, inferred Quaternary strata thin northward and form a growth triangle that is 4.1 to 6.6 km wide at its base, suggesting ??? 2-3 mm/yr of slip on the underlying thrust. The western section of the >40-km-long, north dipping Tacoma fault, extending from Hood Canal to Carr Inlet, forms the western segment of the Tacoma basin margin. Structural relief on this portion of the basin margin may be several kilometers, resulting in steep gravity and aeromagnetic anomalies. Quaternary structural relief along the Tacoma fault is as much as 350-400 m, indicating a minimum slip rate of about 0.2 mm/yr. The inferred eastern section of the Tacoma fault (east of Carr Inlet) crosses the southern part of the Seattle uplift, has variable geometry along strike, and diminished structural relief. The Tacoma fault is regarded as a north dipping backthrust to the Seattle fault, so that slip on a master thrust fault at depth could result in movement on the Seattle fault, the Tacoma fault, or both.

Late Cenozoic extensional faulting in Central-Western Peloponnesus, Greece

NASA Astrophysics Data System (ADS)

Skourtsos, E.; Fountoulis, I.; Mavroulis, S.; Kranis, H.

2012-04-01

A series of forearc-dipping, orogen-parallel extensional faults are found in the central-western Peloponnesus, (south-western Aegean) which control the western margin of Mt Mainalon. The latter comprises HP/LT rocks of the Phyllites-Quartzites Unit (PQ), overlain by the carbonates and flysch of the Tripolis Unit while the uppermost nappe is the Pindos Unit, a sequence of Mesozoic pelagic sequence, topped by a Paleocene flysch. Most of the extensional structures were previously thought of as the original thrust between the Pindos and Tripolis Units. However, the cross-cutting relationships among these structures indicate that these are forearc (SW-dipping) extensional faults, downthrowing the Pindos thrust by a few tens or hundreds of meters each, rooting onto different levels of the nappe pile. In SW Mainalon the lowermost of the extensional faults is a low-angle normal fault dipping SW juxtaposing the metamorphic rocks of the PQ Unit against the non-metamorphic sequence of the Tripolis Unit. High-angle normal faults, found further to the west, have truncated or even sole onto the low-angle ones and control the eastern margin of the Quaternary Megalopolis basin. All these extensional structures form the eastern boundary of a series of Neogene-Quaternary tectonic depressions, which in turn are separated by E-W horsts. In the NW, these faults are truncated by NE to NNE-striking, NW-dipping faults, which relay the whole fault activity to the eastern margin of the Pyrgos graben. The whole extensional fault architecture has resulted (i) in the Pindos thrust stepping down from altitudes higher than 1000 m in Mainalon in the east, to negative heights in North Messinia and Southern Ilia in the west; and (ii) the gradual disappearance of the Phyllite-Quartzite metamorphics of Mainalon towards the west. The combination of these extensional faults (which may reach down to the Ionian décollement) with the low-angle floor thrusts of the Pindos, Tripolis and Ionian Units leads to additional ENE-WSW shortening, normal to the Hellenic Arc, west of the Peloponnesus.

Deepwater Fold-and-Thrust Belt Along New Caledonia's Western Margin: Relation to Post-obduction Vertical Motions

NASA Astrophysics Data System (ADS)

Collot, J.; Patriat, M.; Etienne, S.; Rouillard, P.; Soetaert, F.; Juan, C.; Marcaillou, B.; Palazzin, G.; Clerc, C.; Maurizot, P.; Pattier, F.; Tournadour, E.; Sevin, B.; Privat, A.

2017-10-01

Classically, deepwater fold-and-thrust belts are classified in two main types, depending if they result from near- or far-field stresses and the understanding of their driving and triggering mechanism is poorly known. We present a geophysical data set off the western margin of New Caledonia (SW Pacific) that reveals deformed structures of a deepwater fold-and-thrust belt that we interpret as a near-field gravity-driven system, which is not located at a rifted passive margin. The main factor triggering deformation is inferred to be oversteepening of the margin slope by postobduction isostatic rebound. Onshore erosion of abnormally dense obducted material, combined with sediment loading in the adjacent basin, has induced vertical motions that have caused oversteepening of the margin. Detailed morphobathymetric, seismic stratigraphic, and structural analysis reveals that the fold-and-thrust belt extends 200 km along the margin, and 50 km into the New Caledonia Trough. Deformation is rooted at depths greater than 5 km beneath the seafloor, affects an area of 3,500 km2, and involves a sediment volume of approximately 13,000 km3. This deformed belt is organized into an imbricate fan system of faults, and one out-of-sequence thrust fault affects the seabed. The thrust faults are deeply rooted in the basin along a low-angle floor thrust and connected to New Caledonia Island along a major detachment. This study not only provides a better knowledge of the New Caledonia margin but also provides new insight into the mechanisms that trigger deepwater fold-and-thrust belts.

Actively dewatering fluid-rich zones along the Costa Rica plate boundary fault

NASA Astrophysics Data System (ADS)

Bangs, N. L.; McIntosh, K. D.; Silver, E. A.; Kluesner, J. W.; Ranero, C. R.; von Huene, R.

2012-12-01

New 3D seismic reflection data reveal distinct evidence for active dewatering above a 12 km wide segment of the plate boundary fault within the Costa Rica subduction zone NW of the Osa Peninsula. In the spring of 2011 we acquired a 11 x 55 km 3D seismic reflection data set on the R/V Langseth using four 6,000 m streamers and two 3,300 in3 airgun arrays to examine the structure of the Costa Rica margin from the trench into the seismogenic zone. We can trace the plate-boundary interface from the trench across our entire survey to where the plate-boundary thrust lies > 10 km beneath the margin shelf. Approximately 20 km landward of the trench beneath the mid slope and at the updip edge of the seismogenic zone, a 12 km wide zone of the plate-boundary interface has a distinctly higher-amplitude seismic reflection than deeper or shallower segments of the fault. Directly above and potentially directly connected with this zone are high-amplitude, reversed-polarity fault-plane reflections that extend through the margin wedge and into overlying slope sediment cover. Within the slope cover, high-amplitude reversed-polarity reflections are common within the network of closely-spaced nearly vertical normal faults and several broadly spaced, more gently dipping thrust faults. These faults appear to be directing fluids vertically toward the seafloor, where numerous seafloor fluid flow indicators, such as pockmarks, mounds and ridges, and slope failure features, are distinct in multibeam and backscatter images. There are distinctly fewer seafloor and subsurface fluid flow indicators both updip and downdip of this zone. We believe these fluids come from a 12 km wide fluid-rich segment of the plate-boundary interface that is likely overpressured and has relatively low shear stress.

Area balance and strain in an extensional fault system: Strategies for improved oil recovery in fractured chalk, Gilbertown Field, southwestern Alabama. Annual report, March 1996--March 1997

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pashin, J.C.; Raymond, D.E.; Rindsberg, A.K.

1997-08-01

Gilbertown Field is the oldest oil field in Alabama and produces oil from chalk of the Upper Cretaceous Selma Group and from sandstone of the Eutaw Formation along the southern margin of the Gilbertown fault system. Most of the field has been in primary recovery since establishment, but production has declined to marginally economic levels. This investigation applies advanced geologic concepts designed to aid implementation of improved recovery programs. The Gilbertown fault system is detached at the base of Jurassic salt. The fault system began forming as a half graben and evolved in to a full graben by the Latemore » Cretaceous. Conventional trapping mechanisms are effective in Eutaw sandstone, whereas oil in Selma chalk is trapped in faults and fault-related fractures. Burial modeling establishes that the subsidence history of the Gilbertown area is typical of extensional basins and includes a major component of sediment loading and compaction. Surface mapping and fracture analysis indicate that faults offset strata as young as Miocene and that joints may be related to regional uplift postdating fault movement. Preliminary balanced structural models of the Gilbertown fault system indicate that synsedimentary growth factors need to be incorporated into the basic equations of area balance to model strain and predict fractures in Selma and Eutaw reservoirs.« less

Colorado Basin Structure and Rifting, Argentine passive margin

NASA Astrophysics Data System (ADS)

Autin, Julia; Scheck-Wenderoth, Magdalena; Loegering, Markus; Anka, Zahie; Vallejo, Eduardo; Rodriguez, Jorge; Marchal, Denis; Reichert, Christian; di Primio, Rolando

2010-05-01

The Argentine margin presents a strong segmentation with considerable strike-slip movements along the fracture zones. We focus on the volcanic segment (between the Salado and Colorado transfer zones), which is characterized by seaward dipping reflectors (SDR) all along the ocean-continent transition [e.g. Franke et al., 2006; Gladczenko et al., 1997; Hinz et al., 1999]. The segment is structured by E-W trending basins, which differs from the South African margin basins and cannot be explained by classical models of rifting. Thus the study of the relationship between the basins and the Argentine margin itself will allow the understanding of their contemporary development. Moreover the comparison of the conjugate margins suggests a particular evolution of rifting and break-up. We firstly focus on the Colorado Basin, which is thought to be the conjugate of the well studied Orange Basin [Hirsch et al., 2009] at the South African margin [e.g. Franke et al., 2006]. This work presents results of a combined approach using seismic interpretation and structural, isostatic and thermal modelling highlighting the structure of the crust. The seismic interpretation shows two rift-related discordances: one intra syn-rift and the break-up unconformity. The overlying sediments of the sag phase are less deformed (no sedimentary wedges) and accumulated before the generation of oceanic crust. The axis of the Colorado Basin trends E-W in the western part, where the deepest pre-rift series are preserved. In contrast, the basin axis turns to a NW-SE direction in its eastern part, where mainly post-rift sediments accumulated. The most distal part reaches the margin slope and opens into the oceanic basin. The general basin direction is almost orthogonal to the present-day margin trend. The most frequent hypothesis explaining this geometry is that the Colorado Basin is an aborted rift resulting from a previous RRR triple junction [e.g. Franke et al., 2002]. The structural interpretation partly supports this hypothesis and shows two main directions of faulting: margin-parallel faults (~N30°) and rift-parallel faults (~N125°). A specific distribution of the two fault sets is observed: margin-parallel faults are restrained to the most distal part of the margin. Starting with a 3D structural model of the basin fill based on seismic and well data the deeper structure of the crust beneath the Colorado Basin can be evaluate using isostatic and thermal modelling. Franke, D., et al. (2002), Deep Crustal Structure Of The Argentine Continental Margin From Seismic Wide-Angle And Multichannel Reflection Seismic Data, paper presented at AAPG Hedberg Conference "Hydrocarbon Habitat of Volcanic Rifted Passive Margins", Stavanger, Norway Franke, D., et al. (2006), Crustal structure across the Colorado Basin, offshore Argentina Geophysical Journal International 165, 850-864. Gladczenko, T. P., et al. (1997), South Atlantic volcanic margins Journal of the Geological Society, London 154, 465-470. Hinz, K., et al. (1999), The Argentine continental margin north of 48°S: sedimentary successions, volcanic activity during breakup Marine and Petroleum Geology 16(1-25). Hirsch, K. K., et al. (2009), Tectonic subsidence history and thermal evolution of the Orange Basin, Marine and Petroleum Geology, in press, doi:10.1016/j.marpetgeo.2009.1006.1009

Kinematic development of the Tibetan Plateau's northern margin: A traverse across the Qilian Shan-Nan Shan thrust belt

NASA Astrophysics Data System (ADS)

Zuza, A. V.; Levy, D. A.; Wang, Z.; Xiong, X.; Chen, X.

2017-12-01

The active Cenozoic Qilian Shan-Nan Shan thrust belt defines the northern margin of the Tibetan Plateau. The kinematic development of this thrust belt has implications models of plateau growth and Himalayan-Tibetan orogen strain accommodation. We present new field observations and analytical data from a traverse across the 350-km-wide doubly vergent Qilian Shan, which is bound by the south-dipping North Qilian thrust system in the north and the north-dipping range-bounding Qinghai Nanshan-Dulan Shan thrust system in the south. These faults, and several other major thrusts within the thrust-belt interior, disrupt relatively thick Oligocene-Miocene basin deposits. Of note, many of the thrust faults across the width of the Qilian Shan have Quaternary fault scarps, indicating that active deformation is distributed and not only concentrated along the northern frontal faults. By integrating our detailed structural traverse with new geophysical observations and thermochronology data across the northern plateau margin, we construct a kinematic model for the development of the Tibetan Plateau's northern margin. Deformation initiated in the Eocene-Oligocene along the north-dipping Qinghai Nanshan-Dulan Shan and south-dipping Tuolai Nan Shan thrusts, the latter of which then defined the northern boundary of the Tibetan Plateau. This early deformation was focused along preexisting early Paleozoic structures. A 200-km-wide basin formed between these ranges, and from the Miocene to present, new thrust- and strike-slip-fault-bounded ranges developed, including the north-directed North Qilian and the south-directed Tuolai Nan thrusts. Thus, our observations do not support northward propagating thrust-belt expansion. Instead, we envision that the initial thrust-belt development generated a wide Oligocene-Miocene north-plateau basin that was subsequently disintegrated by later Miocene to present thrusting and strike-slip faulting. Ultimately, the Qilian Shan-Nan Shan thrust belt differs from a typical orogenic thrust wedge, and active deformation is distributed across the range.

Brittle deformation along the Gulf of Alaska margin in response to Paleocene-Eocene triple junction migration: in Sisson

USGS Publications Warehouse

Haeussler, Peter J.; Bradley, Dwight C.; Goldfarb, Richard J.

2003-01-01

A spreading center was subducted diachronously along a 2200 km segment of what is now the Gulf of Alaska margin between 61 and 50 Ma, and left in its wake near-trench intrusions and high-T, low-P metamorphic rocks. Gold-quartz veins and dikes, linked to ridge subduction by geochronological and relative timing evidence, provide a record of brittle deformation during and after passage of the ridge. The gold-quartz veins are typically hosted by faults, and their regional extent indicates there was widespread deformation of the forearc above the slab window at the time of ridge subduction. Considerable variability in the strain pattern was associated with the slab window and the trailing plate. A diffuse network of dextral, sinistral, and normal faults hosted small lode-gold deposits (<50,000 oz) in south-central Alaska, whereas crustal-scale dextral faults in southeastern Alaska are spatially associated with large gold deposits (up to 800,000 oz).We interpret the gold-quartz veins as having formed above an eastward-migrating slab window, where the forearc crust responded to the diminishing influence of the forward subducting plate, the increasing influence of the trailing plate, and the thermal pulse and decreased basal friction from the slab window. In addition, extensional deformation of the forearc resulted from the diverging motions of the two oceanic plates at the margins of the slab window. Factors that complicate interpretations of fault kinematics and near-trench dike orientations include a change in plate motions at ca. 52 Ma, northward translation of the accretionary complex, oroclinal bending of the south-central Alaska margin, and subduction of transform segments. We find the pattern of syn-ridge subduction faulting in southern Alaska is remarkably similar to brittle faults near the Chile triple junction and to earthquake focal mechanisms in the Woodlark basin - the two modern sites of ridge subduction. Therefore, extensional and strike-slip deformation above slab windows may be a common occurrence.

Crustal structure of the Ionian basin and eastern Sicily margin : results from a wide angle seismic survey and implication for the crustal nature and origin of the basin, and the recent tear fault location

NASA Astrophysics Data System (ADS)

Gutscher, M. A.; Dellong, D.; Klingelhoefer, F.; Kopp, H.; Graindorge, D.; Margheriti, L.; Moretti, M.

2017-12-01

In the Ionian Sea (Central Mediterranean) the slow convergence between Africa and Eurasia results in the formation of a narrow subduction zone. The nature of the crust and lithosphere of the subducting plate remain debated and could represent the last remnants of the Neo-Tethys ocean. The rifting mechanism that produced the Ionian basin are also still under discussion with the Malta escarpment representing a possible remnant of this opening. At present, this subduction is still retreating to the south-east (motion occurring since the last 35 Ma) but is confined to the narrow Ionian Basin. In order to accommodate slab roll-back, a major lateral slab tear fault is required. This fault is thought to propagate along the eastern Sicily margin but its precise location remains controversial. This study focuses on the deep crustal structure of the Eastern-Sicily margin and the Malta Escarpment by presenting two wide-angle velocity profiles crossing these structures roughly orthogonally. The data used for the forward velocity modeling were acquired onboard the R/V Meteor during the DIONYSUS cruise in 2014. The results image an oceanic crust within the Ionian basin as well as the deep structure of the Malta Escarpment which presents characteristics of a transform margin. A deep and asymmetrical sedimentary basin is imaged south of the Messina strait and seems to have opened in between the Calabrian and Peloritan continental terranes. The interpretation of the velocity models suggests that the tear fault is located east of the Malta Escarpment, along the Alfeo fault system.

Chapter 2. Borderlands environment, past and present

Treesearch

Guadalupe Sanchez de Carpenter; A.C. MacWilliams

2006-01-01

The major mountain ranges in the study area today were produced by Middle Miocene and younger extensional faulting. Faulting continued into the late Pleistocene as evidenced by fault scarps along the margins of the Animas, Hachita, and Playas Valleys. These long-term geologic events resulted in the present basin and range physiography of the Malpai Borderlands, as...

Breaks in Pavement and Pipes as Indicators of Range-Front Faulting Resulting from the 1989 Loma Prieta Earthquake near the Southwest Margin of the Santa Clara Valley, California

USGS Publications Warehouse

Schmidt, Kevin M.; Ellen, Stephen D.; Haugerud, Ralph A.; Peterson, David M.; Phelps, Geoffery A.

1995-01-01

Damage to pavement and near-surface utility pipes, caused by the October 17, 1989, Loma Prieta earthquake, provide indicators for ground deformation in a 663 km2 area near the southwest margin of the Santa Clara Valley, California. The spatial distribution of 1284 sites of such damage documents the extent and distribution of detectable ground deformation. Damage was concentrated in four zones, three of which are near previously mapped faults. The zone through Los Gatos showed the highest concentration of damage, as well as evidence for pre- and post-earthquake deformation. Damage along the foot of the Santa Cruz Mountains reflected shortening that is consistent with movement along reverse faults in the region and with the hypothesis that tectonic strain is distributed widely across numerous faults in the California Coast Ranges.

High resolution 2D numerical models from rift to break-up: Crustal hyper-extension, Margin asymmetry, Sequential faulting

NASA Astrophysics Data System (ADS)

Brune, Sascha; Heine, Christian; Pérez-Gussinyé, Marta; Sobolev, Stephan

2013-04-01

Numerical modelling is a powerful tool to integrate a multitude of geological and geophysical data while addressing fundamental questions of passive margin formation such as the occurrence of crustal hyper-extension, (a-)symmetries between conjugate margin pairs, and the sometimes significant structural differences between adjacent margin segments. This study utilises knowledge gathered from two key examples of non-magmatic, asymmetric, conjugate margin pairs, i.e. Iberia-New Foundland and Southern Africa-Brazil, where many published seismic lines provide solid knowledge on individual margin geometry. While both margins involve crustal hyper-extension, it is much more pronounced in the South Atlantic. We investigate the evolution of these two margin pairs by carefully constraining our models with detailed plate kinematic history, laboratory-based rheology, and melt fraction evaluation of mantle upwelling. Our experiments are consistent with observed fault patterns, crustal thickness, and basin stratigraphy. We conduct 2D thermomechanical rift models using the finite element code SLIM3D that operates with nonlinear stress- and temperature-dependent elasto-visco-plastic rheology, with parameters provided by laboratory experiments on major crustal and upper mantle rocks. In our models we also calculate the melt fraction within the upwelling asthenosphere, which allows us to control whether the model indeed corresponds to the non-magmatic margin type or not. Our modelling highlights two processes as fundamental for the formation of hyper-extension and margin asymmetry at non-magmatic margins: (1) Strain hardening in the rift center due to cooling of upwelling mantle material (2) The formation of a weak crustal domain adjacent to the rift center caused by localized viscous strain softening and heat transfer from the mantle. Simultaneous activity of both processes promotes lateral rift migration in a continuous way that generates a wide layer of hyper-extended crust on one side of the rift basin. This mechanism implies that syn-rift deformation at the distal margin postdates faulting at the proximal margin by several million years. The succession of events holds intriguing implications not only for peak heat flow migration but also for processes like serpentinization and magmatic underplating.

The continent-ocean transition at the mid-northern margin of the South China Sea

NASA Astrophysics Data System (ADS)

Gao, Jinwei; Wu, Shiguo; McIntosh, Kirk; Mi, Lijun; Yao, Bochu; Chen, Zeman; Jia, Liankai

2015-07-01

The northern margin of the South China Sea (SCS) has particular structural and stratigraphic characteristics that are somewhat different from those described in typical passive margin models. The differences are attributable to poly-phase tectonic movements and magmatic activity resulting from the interaction among the Eurasian, Philippine Sea and Indo-Australian plates. Based on several crustal-scale multi-channel seismic reflection profiles and satellite gravity data across the northern SCS margin, this paper analyzes the structures, volcanoes and deep crust of the continent-ocean transition zone (COT) at the mid-northern margin of the SCS to study the patterns and model of extension there. The results indicate that the COT is limited landward by basin-bounding faults near Baiyun sag and is bounded by seaward-dipping normal faults near the oceanic basin in our seismic lines. The shallow anatomy of the COT is characterized by rift depression, structural highs with igneous rock and/or a volcanic zone or a zone of tilted fault blocks at the distal edge. Gravity modeling revealed that a high velocity layer (HVL) with a 0.8-6-km thickness is frequently present in the slope below the lower crust. Our study shows that the HVL is only located in the eastern portion of the northern SCS margin based on the available geophysical data. We infer from this that the presence of an HVL is not required in the COT at the northern SCS margin. The magmatic intrusions and HVL may be related to partial melting caused by the decompression of a passive, upwelling asthenosphere, which resulted primarily in post-rifting underplating and magmatic emplacement or modification of the crust. Based on this study, we propose that an intermediate mode of rifting was active in the mid-northern margin of the SCS with characteristics that are closer to those of the magma-poor margins than those of volcanic margins.

Glacier ice mass fluctuations and fault instability in tectonically active Southern Alaska

NASA Astrophysics Data System (ADS)

Sauber, Jeanne M.; Molnia, Bruce F.

2004-07-01

Across the plate boundary zone in south central Alaska, tectonic strain rates are high in a region that includes large glaciers undergoing wastage (glacier retreat and thinning) and surges. For the coastal region between the Bering and Malaspina Glaciers, the average ice mass thickness changes between 1995 and 2000 range from 1 to 5 m/year. These ice changes caused solid Earth displacements in our study region with predicted values of -10 to 50 mm in the vertical and predicted horizontal displacements of 0-10 mm at variable orientations. Relative to stable North America, observed horizontal rates of tectonic deformation range from 10 to 40 mm/year to the north-northwest and the predicted tectonic uplift rates range from approximately 0 mm/year near the Gulf of Alaska coast to 12 mm/year further inland. The ice mass changes between 1995 and 2000 resulted in discernible changes in the Global Positioning System (GPS) measured station positions of one site (ISLE) located adjacent to the Bagley Ice Valley and at one site, DON, located south of the Bering Glacier terminus. In addition to modifying the surface displacements rates, we evaluated the influence ice changes during the Bering glacier surge cycle had on the background seismic rate. We found an increase in the number of earthquakes ( ML≥2.5) and seismic rate associated with ice thinning and a decrease in the number of earthquakes and seismic rate associated with ice thickening. These results support the hypothesis that ice mass changes can modulate the background seismic rate. During the last century, wastage of the coastal glaciers in the Icy Bay and Malaspina region indicates thinning of hundreds of meters and in areas of major retreat, maximum losses of ice thickness approaching 1 km. Between the 1899 Yakataga and Yakutat earthquakes ( Mw=8.1, 8.1) and prior to the 1979 St. Elias earthquake ( Ms=7.2), the plate interface below Icy Bay was locked and tectonic strain accumulated. We used estimated ice mass change during the 1899-1979 time period to calculate the change in the fault stability margin (FSM) prior to the 1979 St. Elias earthquake. Our results suggest that a cumulative decrease in the fault stability margin at seismogenic depths, due to ice wastage over 80 years, was large, up to ˜2 MPa. Ice wastage would promote thrust faulting in events such as the 1979 earthquake and subsequent aftershocks.

Glacier ice mass fluctuations and fault instability in tectonically active Southern Alaska

USGS Publications Warehouse

Sauber, J.M.; Molnia, B.F.

2004-01-01

Across the plate boundary zone in south central Alaska, tectonic strain rates are high in a region that includes large glaciers undergoing wastage (glacier retreat and thinning) and surges. For the coastal region between the Bering and Malaspina Glaciers, the average ice mass thickness changes between 1995 and 2000 range from 1 to 5 m/year. These ice changes caused solid Earth displacements in our study region with predicted values of -10 to 50 mm in the vertical and predicted horizontal displacements of 0-10 mm at variable orientations. Relative to stable North America, observed horizontal rates of tectonic deformation range from 10 to 40 mm/year to the north-northwest and the predicted tectonic uplift rates range from approximately 0 mm/year near the Gulf of Alaska coast to 12 mm/year further inland. The ice mass changes between 1995 and 2000 resulted in discernible changes in the Global Positioning System (GPS) measured station positions of one site (ISLE) located adjacent to the Bagley Ice Valley and at one site, DON, located south of the Bering Glacier terminus. In addition to modifying the surface displacements rates, we evaluated the influence ice changes during the Bering glacier surge cycle had on the background seismic rate. We found an increase in the number of earthquakes (ML???2.5) and seismic rate associated with ice thinning and a decrease in the number of earthquakes and seismic rate associated with ice thickening. These results support the hypothesis that ice mass changes can modulate the background seismic rate. During the last century, wastage of the coastal glaciers in the Icy Bay and Malaspina region indicates thinning of hundreds of meters and in areas of major retreat, maximum losses of ice thickness approaching 1 km. Between the 1899 Yakataga and Yakutat earthquakes (Mw=8.1, 8.1) and prior to the 1979 St. Elias earthquake (M s=7.2), the plate interface below Icy Bay was locked and tectonic strain accumulated. We used estimated ice mass change during the 1899-1979 time period to calculate the change in the fault stability margin (FSM) prior to the 1979 St. Elias earthquake. Our results suggest that a cumulative decrease in the fault stability margin at seismogenic depths, due to ice wastage over 80 years, was large, up to ???2 MPa. Ice wastage would promote thrust faulting in events such as the 1979 earthquake and subsequent aftershocks.

Mantle exhumation at magma-poor rifted margin: a competition between frictional shear zones and thermally weakened necking domains. Consequences on time of breakup at Galicia/Newfoundland margins.

NASA Astrophysics Data System (ADS)

Theunissen, T.; Huismans, R. S.

2017-12-01

Here we present a new analysis and interpretation of basement topography of the transitional domain from continental to oceanic crust along the conjugate margin sections SCREETCH-1 (Newfoundland) and WE-1/ISE-1 (Galicia Bank). The absence of significant syn-rift magmatism in this area allows using 2-D thermo-mechanical modelling to understand the formation of the distal margin and exhumed mantle. We show that plastic strain weakening of the exhumed mantle is required to explain observations on basement morphology, and detachment faulting. Our models predict that the evolution of detachment faulting within the transitional domain depends on the degree of frictional-plastic strain-weakening and varies from a single unique steady state asymmetric low angle detachment fault for large degree of strain weakening to multiple out-of-sequence forming detachments with or without dip reversal for lower amounts of strain-weakening. The model behaviour is a consequence of the competition between weak frictional-plastic shear zones and the thermally weakened necking domain in the footwall. The forward models reproduce elevations, wavelength of exhumed mantle ridges for a narrow range of rift velocitiesbetween 10 and 15 mm/yr and considering the increasing thermal conductivity of peridotites at shallow depth. This causes an efficient cooling of the footwall that has then enough strength to support high topography. The forward models also predict that the peridotite ridge is the breakaway of a second detachment fault that dates the crustal breakup and that rocks on top of the peridotite ridge have experimented a fast cooling (< 2 Ma). We use predictions from these forward models to discuss time of breakup and the position of the first steady state oceanic ridge at Galicia/Newfounlandconjugate margins.

How the structural architecture of the Eurasian continental margin affects the structure, seismicity, and topography of the south central Taiwan fold-and-thrust belt

NASA Astrophysics Data System (ADS)

Brown, Dennis; Alvarez-Marron, Joaquina; Biete, Cristina; Kuo-Chen, Hao; Camanni, Giovanni; Ho, Chun-Wei

2017-07-01

Studies of mountain belts worldwide show that along-strike changes are common in their foreland fold-and-thrust belts. These are typically caused by processes related to fault reactivation and/or fault focusing along changes in sedimentary sequences. The study of active orogens, like Taiwan, can also provide insights into how these processes influence transient features such as seismicity and topography. In this paper, we trace regional-scale features from the Eurasian continental margin in the Taiwan Strait into the south central Taiwan fold-and-thrust belt. We then present newly mapped surface geology, P wave velocity maps and sections, seismicity, and topography data to test the hypothesis of whether or not these regional-scale features of the margin are contributing to along-strike changes in structural style, and the distribution of seismicity and topography in this part of the Taiwan fold-and-thrust belt. These data show that the most important along-strike change takes place at the eastward prolongation of the upper part of the margin necking zone, where there is a causal link between fault reactivation, involvement of basement in the thrusting, concentration of seismicity, and the formation of high topography. On the area correlated with the necking zone, the strike-slip reactivation of east northeast striking extensional faults is causing sigmoidal offset of structures and topography along two main zones. Here basement is not involved in the thrusting; there is weak focusing of seismicity and localized development of topography. We also show that there are important differences in structure, seismicity, and topography between the margin shelf and its necking zone.

Spreading and slope instability at the continental margin offshore Mt Etna, imaged by high-resolution 2D seismic data

NASA Astrophysics Data System (ADS)

Gross, Felix; Krastel, Sebastian; Behrmann, Jan-Hinrich; Papenberg, Cord; Geersen, Jacob; Ridente, Domenico; Latino Chiocci, Francesco; Urlaub, Morelia; Bialas, Jörg; Micallef, Aaron

2015-04-01

Mount Etna is the largest active volcano in Europe. Its volcano edifice is located on top of continental crust close to the Ionian shore in east Sicily. Instability of the eastern flank of the volcano edifice is well documented onshore. The continental margin is supposed to deform as well. Little, however, is known about the offshore extension of the eastern volcano flank and its adjacent continental margin, which is a serious shortcoming in stability models. In order to better constrain the active tectonics of the continental margin offshore the eastern flank of the volcano, we acquired and processed a new marine high-resolution seismic and hydro-acoustic dataset. The data provide new detailed insights into the heterogeneous geology and tectonics of shallow continental margin structures offshore Mt Etna. In a similiar manner as observed onshore, the submarine realm is characterized by different blocks, which are controlled by local- and regional tectonics. We image a compressional regime at the toe of the continental margin, which is bound to an asymmetric basin system confining the eastward movement of the flank. In addition, we constrain the proposed southern boundary of the moving flank, which is identified as a right lateral oblique fault movement north of Catania Canyon. From our findings, we consider a major coupled volcano edifice instability and continental margin gravitational collapse and spreading to be present at Mt Etna, as we see a clear link between on- and offshore tectonic structures across the entire eastern flank. The new findings will help to evaluate hazards and risks accompanied by Mt Etna's slope- and continental margin instability and will be used as a base for future investigations in this region.

Advancing Understanding of Earthquakes by Drilling an Eroding Convergent Margin

NASA Astrophysics Data System (ADS)

von Huene, R.; Vannucchi, P.; Ranero, C. R.

2010-12-01

A program of IODP with great societal relevance is sampling and instrumenting the seismogenic zone. The zone generates great earthquakes that trigger tsunamis, and submarine slides thereby endangering coastal communities containing over sixty percent of the earth’s population. To asses and mitigate this endangerment it is urgent to advance understanding of fault dynamics that allows more timely anticipation of hazardous seismicity. Seismogenesis on accreting and eroding convergent plate boundaries apparently differ because of dissimilar materials along the interplate fault. As the history of instrumentally recorded earthquakes expands the difference becomes clearer. The more homogeneous clay, silt and sand subducted at accreting margins is associated with great earthquakes (M 9) whereas the fragmented upper plate rock that can dominate subducted material along an eroding margin plate interface is associated with many tsunamigenic earthquakes (Bilek, 2010). Few areas have been identified where the seismogenic zone can be reached with scientific drilling. In IODP accreting margins are studied on the NanTroSeize drill transect off Japan where the ultimate drilling of the seismogenic interface may occur by the end of IODP. The eroding Costa Rica margin will be studied in CRISP where a drill program will begin in 2011. The Costa Rican geophysical site survey will be complete with acquisition and processing of 3D seismic data in 2011 but the entire drilling will not be accomplished in IODP. It is appropriate that the accreting margin study be accomplished soon considering the indications of a pending great earthquake that will affect a country that has devoted enormous resources to IODP. However, understanding the erosional end-member is scientifically as important to an understanding of fault mechanics. Transoceanic tsunamis affect the entire Pacific rim where most subduction zones are eroding margins. The Costa Rican subduction zone is less complex operationally and perhaps geologically than the Nankai margin. The developing Central American countries do not have the resources to contribute to IODP but this should not deter acquiring the scientific insights proposed in CRISP considering the broader scientific benefits. Such benefits include the first sampling and instrumentation of an actively eroding plate interface and drilling near or into an earthquake asperity. Drilling an eroding margin should significantly advance understanding of subduction zone fault mechanisms and help improve assessment of future hazardous earthquakes and tsunamis.

Sedimentary architecture of a Plio-Pleistocene proto-back-arc basin: Wanganui Basin, New Zealand

NASA Astrophysics Data System (ADS)

Proust, Jean-Noël; Lamarche, Geoffroy; Nodder, Scott; Kamp, Peter J. J.

2005-11-01

The sedimentary architecture of active margin basins, including back-arc basins, is known only from a few end-members that barely illustrate the natural diversity of such basins. Documenting more of these basins types is the key to refining our understanding of the tectonic evolution of continental margins. This paper documents the sedimentary architecture of an incipient back-arc basin 200 km behind the active Hikurangi subduction margin, North Island, New Zealand. The Wanganui Basin (WB) is a rapidly subsiding, Plio-Pleistocene sedimentary basin located at the southern termination of the extensional back-arc basin of the active Central Volcanic Region (TVZ). The WB is asymmetric with a steep, thrust-faulted, outer (arc-ward) margin and a gentle inner (craton-ward) margin. It contains a 4-km-thick succession of Plio-Pleistocene sediments, mostly lying offshore, composed of shelf platform sediments. It lacks the late molasse-like deposits derived from erosion of a subaerial volcanic arc and basement observed in classical back-arc basins. Detailed seismic stratigraphic interpretations from an extensive offshore seismic reflection data grid show that the sediment fill comprises two basin-scale mega-sequences: (1) a Pliocene (3.8 to 1.35 Ma), sub-parallel, regressive "pre-growth" sequence that overtops the uplifted craton-ward margin above the reverse Taranaki Fault, and (2) a Pleistocene (1.35 Ma to present), divergent, transgressive, "syn-growth" sequence that onlaps: (i) the craton-ward high to the west, and (ii) uplifted basement blocks associated with the high-angle reverse faults of the arc-ward margin to the east. Along strike, the sediments offlap first progressively southward (mega-sequence 1) and then southeastward (mega-sequence 2), with sediment transport funnelled between the craton- and arc-ward highs, towards the Hikurangi Trough through the Cook Strait. The change in offlap direction corresponds to the onset of arc-ward thrust faulting and the rise of the Axial Ranges at ca 1.75 Ma, resulting in 5100-5700 m of differential subsidence across the fault system. Sedimentation has propagated south- to southeast-ward over the last 4 Myrs at the tip of successive back-arc graben, volcanic arcs and the associated thermally uplifted parts of the North Island, following the southward migration of the Hikurangi subduction margin. Subsidence occurred by mantle flow-driven flexure, the result of active down-drag of the lithosphere by locking of the Hikurangi subduction interface and sediment loading. The WB is considered to be a proto-back-arc basin that represents the intermediate stage of evolution of an epicratonic shelf platform, impacted by active margin processes.

Crustal Structure of the Ionian Basin and Eastern Sicily Margin: Results From a Wide-Angle Seismic Survey

NASA Astrophysics Data System (ADS)

Dellong, David; Klingelhoefer, Frauke; Kopp, Heidrun; Graindorge, David; Margheriti, Lucia; Moretti, Milena; Murphy, Shane; Gutscher, Marc-Andre

2018-03-01

In the Ionian Sea (central Mediterranean) the slow convergence between Africa and Eurasia results in the formation of a narrow subduction zone. The nature of the crust of the subducting plate remains debated and could represent the last remnants of the Neo-Tethys ocean. The origin of the Ionian basin is also under discussion, especially concerning the rifting mechanisms as the Malta Escarpment could represent a remnant of this opening. This subduction retreats toward the south-east (motion occurring since the last 35 Ma) but is confined to the narrow Ionian basin. A major lateral slab tear fault is required to accommodate the slab roll-back. This fault is thought to propagate along the eastern Sicily margin but its precise location remains controversial. This study focuses on the deep crustal structure of the eastern Sicily margin and the Malta Escarpment. We present two two-dimensional P wave velocity models obtained from forward modeling of wide-angle seismic data acquired onboard the R/V Meteor during the DIONYSUS cruise in 2014. The results image an oceanic crust within the Ionian basin as well as the deep structure of the Malta Escarpment, which presents characteristics of a transform margin. A deep and asymmetrical sedimentary basin is imaged south of the Messina strait and seems to have opened between the Calabrian and Peloritan continental terranes. The interpretation of the velocity models suggests that the tear fault is located east of the Malta Escarpment, along the Alfeo fault system.

Acoustic stratigraphy of Bear Lake, Utah-Idaho: late Quaternary sedimentation patterns in a simple half-graben

USGS Publications Warehouse

Colman, Steven M.

2006-01-01

A 277-km network of high-resolution seismic-reflection profiles, supplemented with a sidescan-sonar mosaic of the lake floor, was collected in Bear Lake, Utah–Idaho, in order to explore the sedimentary framework of the lake's paleoclimate record. The acoustic stratigraphy is tied to a 120 m deep, continuously cored drill hole in the lake. Based on the age model for the drill core, the oldest continuously mapped acoustic reflector in the data set has an age of about 100 ka, although older sediments were locally imaged. The acoustic stratigraphy of the sediments below the lake indicates that the basin developed primarily as a simple half-graben, with a steep normal-fault margin on the east and a flexural margin on the west. As expected for a basin controlled by a listric master fault, seismic reflections steepen and diverge toward the fault, bounding eastward-thickening sediment wedges. Secondary normal faults west of the master fault were imaged beneath the lake and many of these faults show progressively increasing offset with depth and age. Several faults cut the youngest sediments in the lake as well as the modern lake floor. The relative simplicity of the sedimentary sequence is interrupted in the northwestern part of the basin by a unit that is interpreted as a large (4 × 10 km) paleodelta of the Bear River. The delta overlies a horizon with an age of about 97 ka, outcrops at the lake floor and is onlapped by much of the uppermost sequence of lake sediments. A feature interpreted as a wave-cut bench occurs in many places on the western side of the lake. The base of this bench occurs at a depth (22–24 m) similar to that (20–25 m) of the distal surface of the paleodelta. Pinch-outs of sedimentary units are common in relatively shallow water on the gentle western margin of the basin and little Holocene sediment has accumulated in water depths of less than 30 m. On the steep eastern margin of the basin, sediments commonly onlap the hanging wall of the East Bear Lake Fault. However, no major erosional or depositional features suggestive of shoreline processes were observed on acoustic profiles in water deeper than about 20–25 m.

Active Deformation along the Southern End of the Tosco-Abreojos Fault System: New Insights from Multibeam Swath Bathymetry

NASA Astrophysics Data System (ADS)

Michaud, François; Calmus, Thierry; Ratzov, Gueorgui; Royer, Jean-Yves; Sosson, Marc; Bigot-Cormier, Florence; Bandy, William; Mortera Gutiérrez, Carlos

2011-08-01

The relative motion of the Pacific plate with respect to the North America plate is partitioned between transcurrent faults located along the western margin of Baja California and transform faults and spreading ridges in the Gulf of California. However, the amount of right lateral offset along the Baja California western margin is still debated. We revisited multibeam swath bathymetry data along the southern end of the Tosco-Abreojos fault system. In this area the depths are less than 1,000 m and allow a finer gridding at 60 m cell spacing. This improved resolution unveils several transcurrent right lateral faults offsetting the seafloor and canyons, which can be used as markers to quantify local offsets. The seafloor of the southern end of the Tosco-Abreojos fault system (south of 24°N) displays NW-SE elongated bathymetric highs and lows, suggesting a transtensional tectonic regime associated with the formation of pull-apart basins. In such an active tectonic context, submarine canyon networks are unstable. Using the deformation rate inferred from kinematic predictions and pull-apart geometry, we suggest a minimum age for the reorganization of the canyon network.

The Continent-Ocean transition across the Galicia margin: First observations from the Galicia 3D volume

NASA Astrophysics Data System (ADS)

Lymer, Gaël; Cresswell, Derren; Reston, Tim; Stevenson, Carl; Bull, Jon; Sawyer, Dale; Morgan, Julia

2017-04-01

The west Galicia margin has been at the forefront 2D models of breakup subsequently applied to other margins. In summer 2013, a 3D multi-channel seismic dataset was acquired over the Galicia margin with the aim to revisit the margin from a 3D perspective and understand processes of continental extension and break-up through seismic imaging. The volume has been processed through to prestack time migration, followed by depth conversion using velocities extracted from new velocity models based on wide-angle data. Our first interpretations have shown that the most recent block-bounding faults detach downward on a bright reflector, the S reflector, corresponding to a rooted detachment fault and locally the crust-mantle boundary. The 3D topographic and amplitude maps of the S reveal a series of slip surface "corrugations" whose orientation changes oceanward from E-W to ESE-WNW and that we relate to the slip direction during the rifting. We now focus our investigations on the distal part of the S, just east of the Peridotite Ridge, a ridge of exhumed serpentinized mantle. While the S is mainly a continuous surface beneath the continental crust, it suddenly loses its reflectivity oceanward nearby the eastern flank of the ridge. It is likely that the S stops abruptly because it has been offset for almost 1 STWTT by some landward-dipping faults associated with the development of the ridge. This configuration is particularly defendable in the north of the dataset. The implication would be that in this area, the S is shallow and lies below very thin or inexistent basement, thus providing an ideal target for ODP drilling. Alternatively, the S could be intensively segmented by small-offset, but abundant, west-dipping normal faults that root downward on a persistent landward dipping fault that bounds the eastern flank of the ridge. Such a dissection of the S could also explain its lack of reflectivity nearby the ridge; similar reduced reflectivity is locally observed in other parts of the 3D volume in the vicinity of the faults that bound the continental crustal blocks. The implication would be that the S is still located at depth below intensively broken slices of crust and stops against the eastern flank of the Peridotite Ridge. Both cases show that rifting to break-up was a complex and time-variant 3D process that involved several generations of faulting, including late potential landward-dipping structures that controlled the development of the peridotite ridge.

Active transfer fault zone linking a segmented extensional system (Betics, southern Spain): Insight into heterogeneous extension driven by edge delamination

NASA Astrophysics Data System (ADS)

Martínez-Martínez, José Miguel; Booth-Rea, Guillermo; Azañón, José Miguel; Torcal, Federico

2006-08-01

Pliocene and Quaternary tectonic structures mainly consisting of segmented northwest-southeast normal faults, and associated seismicity in the central Betics do not agree with the transpressive tectonic nature of the Africa-Eurasia plate boundary in the Ibero-Maghrebian region. Active extensional deformation here is heterogeneous, individual segmented normal faults being linked by relay ramps and transfer faults, including oblique-slip and both dextral and sinistral strike-slip faults. Normal faults extend the hanging wall of an extensional detachment that is the active segment of a complex system of successive WSW-directed extensional detachments which have thinned the Betic upper crust since middle Miocene. Two areas, which are connected by an active 40-km long dextral strike-slip transfer fault zone, concentrate present-day extension. Both the seismicity distribution and focal mechanisms agree with the position and regime of the observed faults. The activity of the transfer zone during middle Miocene to present implies a mode of extension which must have remained substantially the same over the entire period. Thus, the mechanisms driving extension should still be operating. Both the westward migration of the extensional loci and the high asymmetry of the extensional systems can be related to edge delamination below the south Iberian margin coupled with roll-back under the Alborán Sea; involving the asymmetric westward inflow of asthenospheric material under the margins.

A new reconstruction of the Paleozoic continental margin of southwestern North America: Implications for the nature and timing of continental truncation and the possible role of the Mojave-Sonora megashear

USGS Publications Warehouse

Stevens, C.H.; Stone, P.; Miller, J.S.

2005-01-01

Data bearing on interpretations of the Paleozoic and Mesozoic paleogeography of southwestern North America are important for testing the hypothesis that the Paleozoic miogeocline in this region has been tectonically truncated, and if so, for ascertaining the time of the event and the possible role of the Mojave-Sonora megashear. Here, we present an analysis of existing and new data permitting reconstruction of the Paleozoic continental margin of southwestern North America. Significant new and recent information incorporated into this reconstruction includes (1) spatial distribution of Middle to Upper Devonian continental-margin facies belts, (2) positions of other paleogeographically significant sedimentary boundaries on the Paleozoic continental shelf, (3) distribution of Upper Permian through Upper Triassic plutonic rocks, and (4) evidence that the southern Sierra Nevada and western Mojave Desert are underlain by continental crust. After restoring the geology of western Nevada and California along known and inferred strike-slip faults, we find that the Devonian facies belts and pre-Pennsylvanian sedimentary boundaries define an arcuate, generally south-trending continental margin that appears to be truncated on the southwest. A Pennsylvanian basin, a Permian coral belt, and a belt of Upper Permian to Upper Triassic plutons stretching from Sonora, Mexico, into westernmost central Nevada, cut across the older facies belts, suggesting that truncation of the continental margin occurred in the Pennsylvanian. We postulate that the main truncating structure was a left-lateral transform fault zone that extended from the Mojave-Sonora megashear in northwestern Mexico to the Foothills Suture in California. The Caborca block of northwestern Mexico, where Devonian facies belts and pre-Pennsylvanian sedimentary boundaries like those in California have been identified, is interpreted to represent a missing fragment of the continental margin that underwent ???400 km of left-lateral displacement along this fault zone. If this model is correct, the Mojave-Sonora megashear played a direct role in the Pennsylvanian truncation of the continental margin, and any younger displacement on this fault has been relatively small. ?? 2005 Geological Society of America.

Plate convergence, transcurrent faults and internal deformation adjacent to Southeast Asia and the western Pacific

NASA Technical Reports Server (NTRS)

Fitch, T. J.

1971-01-01

A model for oblique convergence between plates of lithosphere is proposed in which at least a fraction of slip parallel to the plate margin results in transcurrent movements on a nearly vertical fault which is located on the continental side of a zone of plate consumption. In an extreme case of complete decoupling only the component of slip normal to the plate margin can be inferred from underthrusting. Recent movements in the western Sunda region provide the most convincing evidence for decoupling of slip, which in this region is thought to be oblique to the plate margin. A speculative model for convergence along the margins of the Philippine Sea is constructed from an inferred direction of oblique slip in the Philippine region. This model requires that the triple point formed by the junction of the Japanese and Izu-Bonin trenches and the Nankai trough migrate along the Sagami trough.

Outer Rise Faulting And Mantle Serpentinization

NASA Astrophysics Data System (ADS)

Ranero, C. R.; Phipps Morgan, J.; McIntosh, K.; Reichert, C.

Dehydration of serpentinized mantle of the downgoing slab has been proposed to cause both intermediate depth earthquakes (50-300 km) and arc volcanism at sub- duction zones. It has been suggested that most of this serpentinization occurs beneath the outer rise; where normal faulting earthquakes due to bending cut > 20 km deep into the lithosphere, allowing seawater to reach and react with underlying mantle. However, little is known about flexural faulting at convergent margins; about how many normal faults cut across the crust and how deeply they penetrate into the man- tle; about the true potential of faults as conduits for fluid flow and how much water can be added through this process. We present evidence that pervasive flexural faulting may cut deep into the mantle and that the amount of faulting vary dramatically along strike at subduction zones. Flexural faulting increases towards the trench axis indicat- ing that active extension occurs in a broad area. Multibeam bathymetry of the Pacific margin of Costa Rica and Nicaragua shows a remarkable variation in the amount of flexural faulting along the incoming ocean plate. Several parameters seem to control lateral variability. Off south Costa Rica thick crust of the Cocos Ridge flexes little, and little to no faulting develops near the trench. Off central Costa Rica, normal thick- ness crust with magnetic anomalies striking oblique to the trench displays small offset faults (~200 m) striking similar to the original seafloor fabric. Off northern Costa Rica, magnetic anomalies strike perpendicular to the trench axis, and a few ~100m-offset faults develop parallel to the trench. Further north, across the Nicaraguan margin, magnetic anomalies strike parallel to the trench and the most widespread faulting de- velops entering the trench. Multichannel seismic reflection images in this area show a pervasive set of trenchward dipping reflections that cross the ~6 km thick crust and extend into the mantle to depths of at least 20 km. Some reflections project updip to offsets in top basement and seafloor, indicating that they are fault plane reflections. Such a deeply penetrating tectonic fabric could have not developed during crustal cre- ation at the paleo-spreading center where the brittle layer is few km thick. Thus, they must be created during flexure of the plate entering the trench. This data imply that deep and widespread serpentinization of the incoming lithosphere can occur when the lithosphere is strongly faulted; that the extent of lithospheric faulting is closely re- lated to the crustal structure of the incoming plate; and that the amount of lithosphere faulting can change dramatically within a hundred km distance along a trench axis.

The Dauki Fault and its Shillong-Sylhet Thrust Anticline-Foredeep Pair: A Footwall Reactivation along the Progressive Burma-India Collision

NASA Astrophysics Data System (ADS)

Seeber, L.; Ferguson, E. K.; Grall, C.; Steckler, M. S.; Betka, P. M.; Akhter, S. H.

2016-12-01

The Shillong Massif and the Sylhet basin form a south-verging anticline-foredeep pair associated with the E-W striking Dauki fault. Fold geometry and receiver-functions identify it as a blind thrust fault dipping north into the craton. This contractional structure may represent an incipient forward jump of the Himalayan front to the trailing margin of India. The Shillong Massif is one of the largest known basement-cored anticlines and is delineated by a relict erosional surface and folded strata. Where best exposed in the central segment, it has a steep southern limb and a gentle northern limb. This asymmetry is mirrored in the Sylhet foredeep, with a steep north flank and low dip south flank. The combined structure has 5 km of relief, most of which developed during the Quaternary. This foredeep overprints a thicker sequence that records the progradation of the Brahmaputra delta. These older strata thicken southward as expected at a passive margin. The Sylhet Traps, which are coeval with India-Antarctica rifting, outcrop along the southern limb of the anticline. Associated basalt dikes are also parallel to the E-W Dauki structure. The basal Cretaceous-Paleogene shallow marine strata onlap northward the regional unconformity above the cratonic and trap rocks. This suggests that the Dauki thrust front traces an E-W segment of the passive margin and former rift. The IndoBurma forearc overrides the Dauki structure 200 km farther west on the foredeep (south) side than on the massif (north) side of the Dauki fault. Much of this differential advance of the Burma deformation front predates the Dauki foredeep and was a response to the shape of the passive margin of India. This deformation front, known locally as the Haflong Fault, crosses obliquely the Dauki thrust front. Evidence includes contractional structures verging up-dip onto the forelimb of the Shillong anticline. The Shillong Massif-Sylhet Foredeep pair has a strong gravity signature that can be traced eastward across most of the IndoBurma Ranges. Correlated topography and drainage features, including the Imphal intramountain basin, and a drainage switch from northward to southward across this basin suggest that this entire gravity anomaly reflects differential uplift along the eastward continuation of the buried Dauki fault and not just a buried passive margin.

Analysis of the geological structure and tectonic evolution of Xingning-Jinghai sag in deep water area, northern South China Sea

NASA Astrophysics Data System (ADS)

Han, Xiaoying; Ren, Jianye; Lin, Zi; Yang, Linlong

2015-04-01

Recent years, oil and gas exploration of the Pearl River Mouth Basin in the northern margin of South China Sea continuously achieved historic breakthroughs. The Xingning-Jinghai sag, which is located in southeast of the Pearl River Mouth Basin, is a deep-water sag with a great exploration potential. Its tectonic evolution is extremely complex. It experienced Mesozoic subduction to Cenozoic intra-continental rifting background, and finally evolved into a deep-water sag of the northern continental margin of South China Sea. The geological characteristics and the tectonic evolution of Xingning-Jinghai sag was closely related to the process of formation and evolution of the passive continental margin of the northern South China Sea. It is confirmed by many geophysical data that compared with adjacent Chaoshan depression, the crustal thickness of Xingning-Jinghai sag was rapidly thinning, and it developed detachment faults with later magmatic intrusion. The development of detachment faults have dynamic significance for the spreading of the South China Sea. Based on the seismic geological interpretation of 2D seismic data in the study area, the characteristics of detachment fault and supra-detachment basin have been proposed in this study. The characteristics of the detachment fault are low angle and high ratio between heave and throw. The geometry of the detachment fault is a typical lisric shape, with the dip of fault decreasing generally from the seismic profile. The detachment basin where sediments are not deposited over a tilting hanging-wall block but onto a tectonically exhumed footwall which is different from the typical half graben basin. Seismic profiles indicate two different structural styles in the east and west part of Xingning-Jinghai sag. In the west of the sag, there developed two large detachment faults, which control their detachment basin systems and the typical H block, and the two detachment faults are dipping landward and seaward, respectively. In the east, affected by the later volcanic activities, Xingning-Jinghai sag deformed complicatedly and developed a series of landward dipping faults, showing the compound graben structure. Combined with the fault activity quantitative calculation, basin subsidence history and other advanced technology, the basin tectonic evolution has been divided into rift stage and post-rift stage. Considering the extension development evolution of Xingning-Jinghai sag and the extension and thinning of lithosphere under the background of spreading of the South China Sea, we argue that the northern margin of the South China lithosphere experienced an intense stretching and thinning stage. At this period, the subsidence of the Xingning-Jinghai sag was controlled by the detachment faults, indicating a rifting stage. With the development of the detachment faults, the thickness of crust was extremely thinned. After the spreading of the South China Sea the whole sag entered into the depression period which was characterized by thermal subsidence.

Meso-Cenozoic tectonic evolution of the SE Brazilian continental margin: Petrographic, kinematic and dynamic analysis of the onshore Araruama Lagoon Fault System

NASA Astrophysics Data System (ADS)

Souza, Pricilla Camões Martins de; Schmitt, Renata da Silva; Stanton, Natasha

2017-09-01

The Ararauama Lagoon Fault System composes one of the most prominent set of lineaments of the SE Brazilian continental margin. It is located onshore in a key tectonic domain, where the basement inheritance rule is not followed. This fault system is characterized by ENE-WSW silicified tectonic breccias and cataclasites showing evidences of recurrent tectonic reactivations. Based on field work, microtectonic, kinematic and dynamic analysis, we reconstructed the paleostresses in the region and propose a sequence of three brittle deformational phases accountable for these reactivations: 1) NE-SW dextral transcurrence; 2) NNW-SSE dextral oblique extension that evolved to NNW-SSE "pure" extension; 3) ENE-WSW dextral oblique extension. These phases are reasonably correlated with the tectonic events responsible for the onset and evolution of the SE onshore rift basins, between the Neocretaceous and Holocene. However, based on petrographic studies and supported by regional geological correlations, we assume that the origin of this fault system is older, related to the Early Cretaceous South Atlantic rifting. This study provides significant information about one of the main structural trends of the SE Brazilian continental margin and the tectonic events that controlled its segmentation, since the Gondwana rifting, and compartmentalization of its onshore sedimentary deposits during the Cenozoic.

Late Cretaceous-Paleocene strike-slip faults along the East Greenland margin (63°N to 75°N): constraints for the North East Atlantic opening

NASA Astrophysics Data System (ADS)

Guarnieri, P.

2012-04-01

The East Greenland margin is a long stretch starting from 60°N up to 81°N in a distance of almost 3000 km. It represents the conjugate of the European margin now separated by the North East Atlantic (NEA). After a long period of E-W extension and almost N-S oriented rift basins since Early Cretaceous, separation between Greenland and Europe began at 55 Ma following a NE-SW oriented line of breakup and the emplacement of the North Atlantic Igneous Province (NAIP). Post-breakup thermal subsidence followed in the Eocene, and the Oligocene initiated a period of plate re-organization together with the initial separation of Jan Mayen microcontinent, a complex tectonic history with inversion structures and uplifts along both the East Greenland and European margins. The effect of this history is represented by exhumed sedimentary basins, dyke swarms, fault systems, intrusive centers, shield volcanoes and plateau lavas constituting highest mountain of Greenland with some peaks up to 3700 m (e.g. Watkins Bjerge). During expeditions for fieldwork in East Greenland (2009 to 2011) to collect new geological and structural data related to the North East Atlantic tectonics, four areas were visited: Skjoldungen 63°N, Kangerlussuaq 68°N, Traill Ø 72°N and Wollaston Forland 75°N. More than 1000 measurement of fault-slip data for structural analysis along major faults were collected and helicopter flights to collect oblique pictures for 3D-photogeology and 3D-mapping were taken. Kinematic analysis of brittle deformation associated with Late Cretaceous-Paleocene rift shows strike-slip movements. Palaeo-stress tensors reconstructed from fault-slip data highlight a NE-SW maximum horizontal stress in a strike-slip tectonic setting along the entire East Greenland margin (Guarnieri 2011a; Guarnieri 2011b; Guarnieri et al. 2011). Structural data show clear evidence for oblique rifting that corresponds in time to the "volcanic rift" (61-55 Ma) with in some cases the magmatic segmentation of macro-dyke complexes or the activation of major shear zones with strike-slip movements. Oblique rifting and strike-slip deformation along the East Greenland margin reflect the progressive clockwise shift, from W-E to NW-SE, of the separation trend between Greenland and Europe probably in response to the opening of the Labrador Sea.

Applied Time Domain Stability Margin Assessment for Nonlinear Time-Varying Systems

NASA Technical Reports Server (NTRS)

Kiefer, J. M.; Johnson, M. D.; Wall, J. H.; Dominguez, A.

2016-01-01

The baseline stability margins for NASA's Space Launch System (SLS) launch vehicle were generated via the classical approach of linearizing the system equations of motion and determining the gain and phase margins from the resulting frequency domain model. To improve the fidelity of the classical methods, the linear frequency domain approach can be extended by replacing static, memoryless nonlinearities with describing functions. This technique, however, does not address the time varying nature of the dynamics of a launch vehicle in flight. An alternative technique for the evaluation of the stability of the nonlinear launch vehicle dynamics along its trajectory is to incrementally adjust the gain and/or time delay in the time domain simulation until the system exhibits unstable behavior. This technique has the added benefit of providing a direct comparison between the time domain and frequency domain tools in support of simulation validation. This technique was implemented by using the Stability Aerospace Vehicle Analysis Tool (SAVANT) computer simulation to evaluate the stability of the SLS system with the Adaptive Augmenting Control (AAC) active and inactive along its ascent trajectory. The gains for which the vehicle maintains apparent time-domain stability defines the gain margins, and the time delay similarly defines the phase margin. This method of extracting the control stability margins from the time-domain simulation is relatively straightforward and the resultant margins can be compared to the linearized system results. The sections herein describe the techniques employed to extract the time-domain margins, compare the results between these nonlinear and the linear methods, and provide explanations for observed discrepancies. The SLS ascent trajectory was simulated with SAVANT and the classical linear stability margins were evaluated at one second intervals. The linear analysis was performed with the AAC algorithm disabled to attain baseline stability margins. At each time point, the system was linearized about the current operating point using Simulink's built-in solver. Each linearized system in time was evaluated for its rigid-body gain margin (high frequency gain margin), rigid-body phase margin, and aero gain margin (low frequency gain margin) for each control axis. Using the stability margins derived from the baseline linearization approach, the time domain derived stability margins were determined by executing time domain simulations in which axis-specific incremental gain and phase adjustments were made to the nominal system about the expected neutral stability point at specific flight times. The baseline stability margin time histories were used to shift the system gain to various values around the zero margin point such that a precise amount of expected gain margin was maintained throughout flight. When assessing the gain margins, the gain was applied starting at the time point under consideration, thereafter following the variation in the margin found in the linear analysis. When assessing the rigid-body phase margin, a constant time delay was applied to the system starting at the time point under consideration. If the baseline stability margins were correctly determined via the linear analysis, the time domain simulation results should contain unstable behavior at certain gain and phase values. Examples will be shown from repeated simulations with variable added gain and phase lag. Faithfulness of margins calculated from the linear analysis to the nonlinear system will be demonstrated.

Late Pleistocene Activity and deformation features of the North Margin Fault of West Qinling Mountains, northeastern Tibet

NASA Astrophysics Data System (ADS)

Chen, P.; Lin, A.; Yan, B.

2017-12-01

Abstract: A precise constraints of slip rates of active faults within and around Tibetan Plateau will provide us a definite and explicit knowledge of continental dynamics and present-day tectonic evolution. The major strike-slip faults in the northern and northeastern Tibetan Plateau, including the Altyn Tagh fault and Kunlun fault play a vital role in dissipating and transferring the strain energy. The WNW-trending North Margin Fault of West Qinling Mountains (hereafter name NMFWQM, the target of this study) developed along the topographic boundary between Longzhong basin and the Qinling mountains. Intensive Historic records show that large earthquakes repeatedly in the area around the NMFWQM, including the AD 143 M 7.0 Gangu West earthquake; AD 734 M≥7.0 Tianshui earthquake; AD 1654 M 8.0 Tianshui South earthquake and the most recent 2013 Mw6.0 Zhangxian earthquake. In this study, we investigated the structural features and activity of the NMFWQM including the nature of the fault, slip rate, and paleoseismicity by interpretation of high-resolution remote sensing images and field investigation. Based on the interpretations of high resolution satellite images, field investigations and 14C dating ages, we conclude the following conclusions: 1) The drainage systems have been systematical deflected or offset sinistrally along the fault trace; 2) The amounts of displacement (D) show a positive linear correlation with the upstream length (L) from the deflected point of offset river channels as DaL (a: a certain coefficient); 3) The alluvial fans and terrace risers formed in the last interglacial period are systematically offset by 16.4m to 93.9 m, indicating an accumulation of horizontal displacements as that observed in the offset drainages; 4) A horizontal slip rate is estimated to be 2.5-3.1 mm/yr with an average of 2.8 mm/yr. Comparing with the well-know strike-slip active faults developed in the northern Tibetan Plateau, such as the Altyn Tagh fault and Kunlun fault along which the slip rate is estimated to be up to >10 mm/yr, the NMFWQ shows a low slip rate of < 3 mm/yr. We interpret that this low slip rate of the the NMFWQ may be related to the limited convergence transfer and localized deformation in the northernmost margin of the Tibetan Plateau.

Plate break-up geometry in SE-Afar

NASA Astrophysics Data System (ADS)

Geoffroy, Laurent; Le Gall, Bernard; Daoud, Mohamed

2014-05-01

New structural data acquired in Djibouti strongly support the view of a magma-rich to magma-poor pair of conjugate margins developed in SE Afar since at least 9 Ma. Our model is illustrated by a crustal-scale transect that emphasizes the role of a two-stage extensional detachment fault system, with opposing senses of motion through time. The geometry and kinematics of this detachment fault pattern are mainly documented from lavas and fault dip data extracted from remote sensing imagery (Landsat ETM+, and corresponding DEM), further calibrated by field observations. Although expressed by opposite fault geometries, the two successive extensional events evidenced here are part of a two-stage continental extensional tear-system associated with the ongoing propagation of the Aden-Tadjoura oceanic axis to the NW. A flip-flop evolution of detachment faults accommodating lithosphere divergence has recently been proposed for the development of the Indian Ocean and continental margins (Sauter et al., 2013). However, the SE Afar evolution further suggests a radical and sudden change in lithosphere behavior during extension, from a long-term and widespread magmatic stage to a syn-sedimentary break-up stage where mantle melting concentrates along the future oceanic axis. Of special interest is the fact that a late and rapid stage of non-magmatic extension led to break-up, whose geometry triggered the location of the break-up axis and earliest oceanic accretion. New structural data acquired in Djibouti strongly support the view of a magma-rich to magma-poor pair of conjugate margins developed in SE Afar since at least 9 Ma. Our model is illustrated by a crustal-scale transect that emphasizes the role of a two-stage extensional detachment fault system, with opposing senses of motion through time. The geometry and kinematics of this detachment fault pattern are mainly documented from lavas and fault dip data extracted from remote sensing imagery (Landsat ETM+, and corresponding DEM), further calibrated by field observations. Although expressed by opposite fault geometries, the two successive extensional events evidenced here are part of a two-stage continental extensional tear-system associated with the ongoing propagation of the Aden-Tadjoura oceanic axis to the NW. A flip-flop evolution of detachment faults accommodating lithosphere divergence has recently been proposed for the development of the Indian Ocean and continental margins (Sauter et al., 2013). However, the SE Afar evolution further suggests a radical and sudden change in lithosphere behavior during extension, from a long-term and widespread magmatic stage to a syn-sedimentary break-up stage where mantle melting concentrates along the future oceanic axis. Of special interest is the fact that a late and rapid stage of non-magmatic extension led to break-up, whose geometry triggered the location of the break-up axis and earliest oceanic accretion.

Intra-arc Seismicity: Geometry and Kinematic Constraints of Active Faulting along Northern Liquiñe-Ofqui and Andean Transverse Fault Systems [38º and 40ºS, Southern Andes

NASA Astrophysics Data System (ADS)

Sielfeld, G.; Lange, D.; Cembrano, J. M.

2017-12-01

Intra-arc crustal seismicity documents the schizosphere tectonic state along active magmatic arcs. At oblique-convergent margins, a significant portion of bulk transpressional deformation is accommodated in intra-arc regions, as a consequence of stress and strain partitioning. Simultaneously, crustal fluid migration mechanisms may be controlled by the geometry and kinematics of crustal high strain domains. In such domains shallow earthquakes have been associated with either margin-parallel strike-slip faults or to volcano-tectonic activity. However, very little is known on the nature and kinematics of Southern Andes intra-arc crustal seismicity and its relation with crustal faults. Here we present results of a passive seismicity study based on 16 months of data collected from 33 seismometers deployed along the intra-arc region of Southern Andes between 38˚S and 40˚S. This region is characterized by a long-lived interplay among margin-parallel strike-slip faults (Liquiñe-Ofqui Fault System, LOFS), second order Andean-transverse-faults (ATF), volcanism and hydrothermal activity. Seismic signals recorded by our network document small magnitude (0.2P and 2,796 S phase arrival times have been located with NonLinLoc. First arrival polarities and amplitude ratios of well-constrained events, were used for focal mechanism inversion. Local seismicity occurs at shallow levels down to depth of ca. 16 km, associated either with stratovolcanoes or to master, N10˚E, and subsidiary, NE to ENE, striking branches of the LOFS. Strike-slip focal mechanisms are consistent with the long-term kinematics documented by field structural-geology studies. Unexpected, well-defined NW-SE elongated clusters are also reported. In particular, a 72-hour-long, N60˚W-oriented seismicity swarm took place at Caburgua Lake area, describing a ca. 36x12x1km3 faulting crustal volume. Results imply a unique snapshot on shallow crustal tectonics, contributing to the understanding of faulting processes in volcanic arcs and ultimately, providing useful knowledge to improve the quality of hazard assessment communities emplaced in Southern Andes volcanic arc.

Dynamics and materials physics of fault rupture and glacial processes

NASA Astrophysics Data System (ADS)

Platt, John Daniel

This thesis focuses on two main topics, the physics governing how faults rapidly weaken during an earthquake and the thermal and mechanical structure of ice stream shear margins. The common theme linking these two projects is the desire to understand how the complicated interactions between stress and temperature control deformation and failure. All of the problems in this thesis are attacked using a combination of analytic and numerical methods, and the interplay between these two approaches provides a powerful way to understand the different physical balances that dominate in different regimes. We also use aspects of materials science to understand how the often complicated rheologies are controlled by underlying physical phenomena such as melting, phase transitions, diffusion, and dislocation motion. With regards to fault mechanics, we begin by showing how co-seismic weakening mechanisms driven by elevated pore fluid pressures lead to micron-scale strain localization during an earthquake. We solve for the localized zone thickness for a range of fault temperatures, test these predictions using numerical simulations, and show how the onset of localization accelerates fault weakening. Next we present the first solutions to account for thermal decomposition reactions during a dynamic rupture, showing that the activation of thermal decomposition may lead to a larger slip duration and total slip. Finally we present a new set of experiments studying flash heating of serpentinite, highlighting the dependence of friction on normal stress and the presence of gouge, and producing the first model to explain the hysteresis commonly observed in flash heating experiments. With regards to ice stream shear margins, we begin by extending the work of Perol and Rice [2011] to study the formation of temperate ice in shear margins, and quantify the total melt that may be generated within the shear margins. We conclude by investigating how the presence of such a channel alters the stress on and strength of the undeforming bed in the shear margin, showing that the transition from a deforming to an undeforming bed across a channel is stable when the water flux in the channel exceeds a critical value.

Geophysical reassessment of the role of ancient crustal structures on the development of western Laurentia and Selwyn Basin, Yukon and Northwest Territories, Canada.

NASA Astrophysics Data System (ADS)

Hayward, N.

2017-12-01

The structure of the western margin of the North American craton (Laurentia) in the northern Canadian Cordillera and its role in the development of the Neoproterozoic-Early Paleozoic Selwyn Basin are reassessed through 3D inversion of a new compilation of aeromagnetic data and archival Bouguer gravity data. The region's tectonic history is obscured by partial burial beneath Selwyn Basin, and a tectonic overprint that includes terrane accretion, regional plutonism, and strike-slip faults with displacements of 100s and perhaps 1000s of kilometers. Despite the implied complexity, preliminary geological and geophysical based interpretations of the structure of the western margin of Laurentia, have been adopted with few refinements in over two decades. Regionally continuous, NE-trending, crustal lineaments, including the Fort Norman line and Leith Ridge fault, were interpreted as having had long-standing influence on the craton development, its western margin, and overlapping sedimentary basin. New results reveal limited evidence for the regional continuity of the NE-trending lineaments. Instead, models suggest that the structure of the Laurentian margin is characterised by segmentation on numerous shorter structures of varied strike. The western margin of the craton and its structures are bound by a NW-trending structure that connects with the Richardson Trough to the north and may have been active during rifting of the Misty Creek embayment. This boundary also marks the easternmost limit of both granitic intrusions in Selwyn Basin, which gravity models suggest are of greater extent than reflected on geological maps, and SEDEX occurrences. An ENE-trending structure beneath northern Selwyn Basin is interpreted as marking the southern edge of a previously unidentified cratonic promontory, akin to the Liard line that marks a transfer fault that bounds the promontory of the Macdonald Platform, south of Selwyn Basin. The ENE-trending structure is traced from the Tintina fault in the west to near to the Great Bear magmatic zone. The structure's regional continuity also limits the interpretation of a post-Cretaceous structure, inboard of the Tintina fault that could be responsible for 1000's km of dextral strike-slip ascribed to the Baja-BC terrane translation model.

Episodic normal faulting and magmatism during the syn-spreading stage of the Baiyun sag in Pearl River Mouth Basin: response to the multi-phase seafloor spreading of the South China Sea

NASA Astrophysics Data System (ADS)

Deng, Peng; Mei, Lianfu; Liu, Jun; Zheng, Jinyun; Liu, Minghui; Cheng, Zijie; Guo, Fengtai

2018-03-01

Considerable post-breakup extensional deformation is recorded in the continental margins of the South China Sea (SCS). To recognize the nature and origin of the significant deformation during the syn-spreading stage (32-15.5 Ma) in the SCS, we comprehensively analyzed the geometry and kinematics of the faults and contemporaneous magmas in the Baiyun sag, northern margin of the SCS, using high-resolution regional three-dimensional seismic data. The kinematic analyses indicate that the faults in the Baiyun sag are recently formed following the onset of seafloor spreading in the SCS. The faults exhibit multiple episodes of growth history, with three active episodes, 32-29, 23.8-21 and 18.5-16.5 Ma, separated by periods of inactivity. Four volcanic groups comprising 98 volcanic mounds have been identified and described, located separately in the northwestern, the central, the southeastern and the northern slope areas. The occurrence of multiple palaeo-seafloors, complemented by the biostratigraphic and K-Ar dating data, reveals multiple extrusive events of the syn-spreading magmas in the Baiyun sag, with three active periods of 23.8-21, 18.5-17.5 and 17.5-16.5 Ma. This study confirms that the normal faulting has a shared genetic origin with the contemporaneous magmatism during the syn-spreading stage in the deep-offshore Baiyun sag, northern margin of the SCS. The episodic fault growth and magmatic extrusive events reveal that the Baiyun sag has undergone at least three episodic tectonic events during the syn-spreading stage, which evolved in response to the multi-stage seafloor spreading of the SCS.

Synthesis of crustal seismic structure and implications for the concept of a slab gap beneath Coastal California

USGS Publications Warehouse

Brocher, T.M.; ten Brink, Uri S.; Abramovitz, T.

1999-01-01

Compilation of seismic transects across the central and northern California Coast Ranges provides evidence for the widespread tectonic emplacement beneath the margin of a slab of partially subducted oceanic lithosphere. The oceanic crust of this lithosphere can be traced landward from the former convergent margin (fossil trench), beneath the Coast Ranges, to at least as far east as the Coast Range/Great Valley boundary. Comparison of measured shear and compressional wave velocities in the middle crust beneath the Hayward fault with laboratory measurements suggests that the middle crust is a diabase (oceanic crust). Both of these observations are consistent with recent models of the high heat flow and age progression of Neogene volcanism along the Coast Ranges based on tectonic emplacement (stalling) of young, hot oceanic lithosphere beneath the margin, but appear to contradict the major predictions of the slab-gap or asthenospheric-window model. Finally, the Neogene volcanism and major strike-slip faults in the Coast Ranges occur within the thickest regions (>14 km thick) of the forearc, suggesting that the locations of Cenozoic volcanism and faulting along the margin are structurally controlled by the forearc thickness rather than being determined by the location of a broad slab gap.

A note on the effect of fault gouge thickness on fault stability

USGS Publications Warehouse

Byerlee, J.; Summers, R.

1976-01-01

At low confining pressure, sliding on saw cuts in granite is stable but at high pressure it is unstable. The pressure at which the transition takes place increases if the thickness of the crushed material between the sliding surfaces is increased. This experimental result suggests that on natural faults the stability of sliding may be affected by the width of the fault zone. ?? 1976.

Active faults and minor plates in NE Asia

NASA Astrophysics Data System (ADS)

Kozhurin, Andrey I.; Zelenin, Egor A.

2014-05-01

Stated nearly 40 yr ago the uncertainty with plate boundaries location in NE Asia (Chapman, Solomon, 1976) still remains unresolved. Based on the prepositions that a plate boundary must, first, reveal itself in linear sets of active structures, and, second, be continuous and closed, we have undertaken interpretation of medium-resolution KH-9 Hexagon satellite imageries, mostly in stereoscopic regime, for nearly the entire region of NE Asia. Main findings are as follows. There are two major active fault zones in the region north of the Bering Sea. One of them, the Khatyrka-Vyvenka zone, stretches NE to ENE skirting the Bering Sea from the Kamchatka isthmus to the Navarin Cape. Judging by the kinematics of the Olyutorsky 2006 earthquake fault, the fault zones move both right-laterally and reversely. The second active fault zone, the Lankovaya-Omolon zone, starts close to the NE margin of the Okhotsk Sea and extends NE up to nearly the margin of the Chukcha Sea. The fault zone is mostly right-lateral, with topographically expressed cumulative horizontal offsets amounting to 2.5-2.6 km. There may be a third NE-SW zone between the major two coinciding with the Penzhina Range as several active faults found in the southern termination of the Range indicate. The two active fault zones divide the NE Asia area into two large domains, which both could be parts of the Bering Sea plate internally broken and with uncertain western limit. Another variant implies the Khatyrka-Vyvenka zone as the Bering Sea plate northern limit, and the Lankovaya-Omolon zone as separating an additional minor plate from the North-American plate. The choice is actually not crucial, and more important is that both variants leave the question of where the Bering Sea plate boundary is in Alaska. The Lankovaya-Omolon zone stretches just across the proposed northern boundary of the Okhorsk Sea plate. NW of the zone, there is a prominent left-lateral Ulakhan fault, which is commonly interpreted to be a portion of the plate northern boundary. With this, we have discovered no active faults or fault zones of the Ulakhan fault strike, which could be the portion of the boundary between the Lankovaya-Omolon zone and either the western margin of the Komandor basin or the westernmost Aleutians. We conclude that there is a certain disagreement between active faulting pattern and plate models for NE Asia, relating to the extent of the plates and missing portions of the plate boundaries. The research was supported by grant # 110500136-a from the Russian Foundation for Basic Research.

Recent uplift of the Atlantic Atlas (offshore West Morocco): Tectonic arch and submarine terraces

NASA Astrophysics Data System (ADS)

Benabdellouahed, M.; Klingelhoefer, F.; Gutscher, M.-A.; Rabineau, M.; Biari, Y.; Hafid, M.; Duarte, J. C.; Schnabel, M.; Baltzer, A.; Pedoja, K.; Le Roy, P.; Reichert, C.; Sahabi, M.

2017-06-01

Re-examination of marine geophysical data from the continental margin of West Morocco reveals a broad zone characterized by deformation, active faults and updoming offshore the High Atlas (Morocco margin), situated next to the Tafelney Plateau. Both seismic reflection and swath-bathymetric data, acquired during Mirror marine geophysical survey in 2011, indicate recent uplift of the margin including uplift of the basement. This deformation, which we propose to name the Atlantic Atlas tectonic arch, is interpreted to result largely through uplift of the basement, which originated during the Central Atlantic rifting stage - or even during phases of Hercynian deformation. This has produced a large number of closely spaced normal and reverse faults, ;piano key faults;, originating from the basement and affecting the entire sedimentary sequence, as well as the seafloor. The presence of four terraces in the Essaouira canyon system at about 3500 meters water depth and ;piano key faults; and the fact that these also affect the seafloor, indicate that the Atlantic Atlas is still active north of Agadir canyon. We propose that recent uplift is causing morphogenesis of four terraces in the Essaouira canyon system. In this paper the role of both Canary plume migration and ongoing convergence between the African and Eurasian plates in the formation of the Atlantic Atlas are discussed as possibilities to explain the presence of a tectonic arch in the region. The process of reactivation of passive margins is still not well understood. The region north of Agadir canyon represents a key area to better understand this process.

Bounded Linear Stability Margin Analysis of Nonlinear Hybrid Adaptive Control

NASA Technical Reports Server (NTRS)

Nguyen, Nhan T.; Boskovic, Jovan D.

2008-01-01

This paper presents a bounded linear stability analysis for a hybrid adaptive control that blends both direct and indirect adaptive control. Stability and convergence of nonlinear adaptive control are analyzed using an approximate linear equivalent system. A stability margin analysis shows that a large adaptive gain can lead to a reduced phase margin. This method can enable metrics-driven adaptive control whereby the adaptive gain is adjusted to meet stability margin requirements.

Heat flow pattern in the gas hydrate drilling areas of northern south china sea and the implication for further study

NASA Astrophysics Data System (ADS)

Wang, Lifeng; Sha, Zhibin

2015-04-01

Numerous seismic reflection profiles have been acquired by China Geological Survey (CGS) in the Northern Slope of South China Sea (SCS), clearly indicating widespread occurrence of free gases and/or gas hydrates in the sediments. In the year 2007 and 2013 respectively the gas hydrate samples are successfully recovered during two offshore drilling exploratory programs. Results of geothermal data during previous field studies along the north continental margin, however, show that the gas hydrate sites are associated with high geothermal background in contrast to the other offshore ones where the gas hydrates are more likely to be found in the low geothermal regional backgrounds. There is a common interesting heat flow pattern during the two drilling expeditions that the gas hydrate occurrences coincide with the presences of comparatively low geothermal anomalies against the high thermal background which is mainly caused by concentrated fluid upward movements into the stability zone (GHSZ) detected by the surface heat flow measurements over the studied fields. The key point for understanding the coupling between the presences of the gas hydrates and heat flow pattern at regional scale is to know the cause of high heat flows and the origin of forming gases at depth. We propose that these high heat flows are attributed to elevated shallow fault-fissure system due to the tectonic activities. A remarkable series of vertical faults and fissures are common on the upper continental slope and the forming gases are thought to have migrated with hot advective fluid flows towards seafloor mainly via fault-fissure system from underlying source rocks which are deeper levels than those of the GHSZ. The present study is based on an extensive dataset on hydrate distribution and associated temperature field measurements collected in the vicinity of studied areas during a series of field expeditions organized within the framework of national widely collaborative projects. Those observations bring new insights to our growing understanding of the stability of this dynamic hydrate reservoir in the continental margin shallow subsurface, and alert us that occurrence patterns may be more complex than previously thought. So the future aim of this program is to better understand the factors constraining the distribution of hydrate deposits, and the processes involved in gas hydrate formation.

Faulting and hydration of the Juan de Fuca plate system

NASA Astrophysics Data System (ADS)

Nedimović, Mladen R.; Bohnenstiehl, DelWayne R.; Carbotte, Suzanne M.; Pablo Canales, J.; Dziak, Robert P.

2009-06-01

Multichannel seismic observations provide the first direct images of crustal scale normal faults within the Juan de Fuca plate system and indicate that brittle deformation extends up to ~ 200 km seaward of the Cascadia trench. Within the sedimentary layering steeply dipping faults are identified by stratigraphic offsets, with maximum throws of 110 ± 10 m found near the trench. Fault throws diminish both upsection and seaward from the trench. Long-term throw rates are estimated to be 13 ± 2 mm/kyr. Faulted offsets within the sedimentary layering are typically linked to larger offset scarps in the basement topography, suggesting reactivation of the normal fault systems formed at the spreading center. Imaged reflections within the gabbroic igneous crust indicate swallowing fault dips at depth. These reflections require local alteration to produce an impedance contrast, indicating that the imaged fault structures provide pathways for fluid transport and hydration. As the depth extent of imaged faulting within this young and sediment insulated oceanic plate is primarily limited to approximately Moho depths, fault-controlled hydration appears to be largely restricted to crustal levels. If dehydration embrittlement is an important mechanism for triggering intermediate-depth earthquakes within the subducting slab, then the limited occurrence rate and magnitude of intraslab seismicity at the Cascadia margin may in part be explained by the limited amount of water imbedded into the uppermost oceanic mantle prior to subduction. The distribution of submarine earthquakes within the Juan de Fuca plate system indicates that propagator wake areas are likely to be more faulted and therefore more hydrated than other parts of this plate system. However, being largely restricted to crustal levels, this localized increase in hydration generally does not appear to have a measurable effect on the intraslab seismicity along most of the subducted propagator wakes at the Cascadia margin.

The mechanism of post-rift fault activities in Baiyun sag, Pearl River Mouth basin

NASA Astrophysics Data System (ADS)

Sun, Zhen; Xu, Ziying; Sun, Longtao; Pang, Xiong; Yan, Chengzhi; Li, Yuanping; Zhao, Zhongxian; Wang, Zhangwen; Zhang, Cuimei

2014-08-01

Post-rift fault activities were often observed in deepwater basins, which have great contributions to oil and gas migration and accumulation. The main causes for post-rift fault activities include tectonic events, mud or salt diapirs, and gravitational collapse. In the South China Sea continental margin, post-rift fault activities are widely distributed, especially in Baiyun sag, one of the largest deepwater sag with its main body located beneath present continental slope. During the post-rift stage, large population of faults kept active for a long time from 32 Ma (T70) till 5.5 Ma (T10). Seismic interpretation, fault analysis and analogue modeling experiments indicate that the post-rift fault activities in Baiyun sag between 32 Ma (T70) and 13.8 Ma (T30) was mainly controlled by gravity pointing to the Main Baiyun sag, which caused the faults extensive on the side facing Main Baiyun sag and the back side compressive. Around 32 Ma (T70), the breakup of the continental margin and the spreading of the South China Sea shed a combined effect of weak compression toward Baiyun sag. The gravity during post-rift stage might be caused by discrepant subsidence and sedimentation between strongly thinned sag center and wing areas. This is supported by positive relationship between sedimentation rate and fault growth index. After 13.8 Ma (T30), fault activity shows negative relationship with sedimentation rate. Compressive uplift and erosion in seismic profiles as well as negative tectonic subsiding rates suggest that the fault activity from 13.8 Ma (T30) to 5.5 Ma (T10) might be controlled by the subductive compression from the Philippine plate in the east.

The Fault Block Model: A novel approach for faulted gas reservoirs

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ursin, J.R.; Moerkeseth, P.O.

1994-12-31

The Fault Block Model was designed for the development of gas production from Sleipner Vest. The reservoir consists of marginal marine sandstone of Hugine Formation. Modeling of highly faulted and compartmentalized reservoirs is severely impeded by the nature and extent of known and undetected faults and, in particular, their effectiveness as flow barrier. The model presented is efficient and superior to other models, for highly faulted reservoir, i.e. grid based simulators, because it minimizes the effect of major undetected faults and geological uncertainties. In this article the authors present the Fault Block Model as a new tool to better understandmore » the implications of geological uncertainty in faulted gas reservoirs with good productivity, with respect to uncertainty in well coverage and optimum gas recovery.« less

Stability analysis of fuzzy parametric uncertain systems.

PubMed

Bhiwani, R J; Patre, B M

2011-10-01

In this paper, the determination of stability margin, gain and phase margin aspects of fuzzy parametric uncertain systems are dealt. The stability analysis of uncertain linear systems with coefficients described by fuzzy functions is studied. A complexity reduced technique for determining the stability margin for FPUS is proposed. The method suggested is dependent on the order of the characteristic polynomial. In order to find the stability margin of interval polynomials of order less than 5, it is not always necessary to determine and check all four Kharitonov's polynomials. It has been shown that, for determining stability margin of FPUS of order five, four, and three we require only 3, 2, and 1 Kharitonov's polynomials respectively. Only for sixth and higher order polynomials, a complete set of Kharitonov's polynomials are needed to determine the stability margin. Thus for lower order systems, the calculations are reduced to a large extent. This idea has been extended to determine the stability margin of fuzzy interval polynomials. It is also shown that the gain and phase margin of FPUS can be determined analytically without using graphical techniques. Copyright © 2011 ISA. Published by Elsevier Ltd. All rights reserved.

Application of matrix singular value properties for evaluating gain and phase margins of multiloop systems. [stability margins for wing flutter suppression and drone lateral attitude control

NASA Technical Reports Server (NTRS)

Mukhopadhyay, V.; Newsom, J. R.

1982-01-01

A stability margin evaluation method in terms of simultaneous gain and phase changes in all loops of a multiloop system is presented. A universal gain-phase margin evaluation diagram is constructed by generalizing an existing method using matrix singular value properties. Using this diagram and computing the minimum singular value of the system return difference matrix over the operating frequency range, regions of guaranteed stability margins can be obtained. Singular values are computed for a wing flutter suppression and a drone lateral attitude control problem. The numerical results indicate that this method predicts quite conservative stability margins. In the second example if the eigenvalue magnitude is used instead of the singular value, as a measure of nearness to singularity, more realistic stability margins are obtained. However, this relaxed measure generally cannot guarantee global stability.

Faulting of gas-hydrate-bearing marine sediments - contribution to permeability

USGS Publications Warehouse

Dillon, William P.; Holbrook, W.S.; Drury, Rebecca; Gettrust, Joseph; Hutchinson, Deborah; Booth, James; Taylor, Michael

1997-01-01

Extensive faulting is observed in sediments containing high concentrations of methane hydrate off the southeastern coast of the United States. Faults that break the sea floor show evidence of both extension and shortening; mud diapirs are also present. The zone of recent faulting apparently extends from the ocean floor down to the base of gas-hydrate stability. We infer that the faulting resulted from excess pore pressure in gas trapped beneath the gas hydrate-beating layer and/or weakening and mobilization of sediments in the region just below the gas-hydrate stability zone. In addition to the zone of surface faults, we identified two buried zones of faulting, that may have similar origins. Subsurface faulted zones appear to act as gas traps.

Cenozoic sedimentation in the Mumbai Offshore Basin: Implications for tectonic evolution of the western continental margin of India

NASA Astrophysics Data System (ADS)

Nair, Nisha; Pandey, Dhananjai K.

2018-02-01

Interpretation of multichannel seismic reflection data along the Mumbai Offshore Basin (MOB) revealed the tectonic processes that led to the development of sedimentary basins during Cenozoic evolution. Structural interpretation along three selected MCS profiles from MOB revealed seven major sedimentary sequences (∼3.0 s TWT, thick) and the associated complex fault patterns. These stratigraphic sequences are interpreted to host detritus of syn- to post rift events during rift-drift process. The acoustic basement appeared to be faulted with interspaced intrusive bodies. The sections also depicted the presence of slumping of sediments, subsidence, marginal basins, rollover anticlines, mud diapirs etc accompanied by normal to thrust faults related to recent tectonics. Presence of upthrusts in the slope region marks the locations of local compression during collision. Forward gravity modeling constrained with results from seismic and drill results, revealed that the crustal structure beneath the MOB has undergone an extensional type tectonics intruded with intrusive bodies. Results from the seismo-gravity modeling in association with litholog data from drilled wells from the western continental margin of India (WCMI) are presented here.

Cold seeps and splay faults on Nankai margin

NASA Astrophysics Data System (ADS)

Henry, P.; Ashi, J.; Tsunogai, U.; Toki, T.; Kuramoto, S.; Kinoshita, M.; Lallemant, S. J.

2003-04-01

Cold seeps (bacterial mats, specific fauna, authigenic carbonates) are common on the Nankai margin and considered as evidence for seepage of methane bearing fluids. Camera and submersible surveys performed over the years have shown that cold seeps are generally associated with active faults. One question is whether part of the fluids expelled originate from the seismogenic zone and migrate along splay faults to the seafloor. The localisation of most cold seeps on the hanging wall of major thrusts may, however, be interpreted in various ways: (a) footwall compaction and diffuse flow (b) fluid channelling along the fault zone at depths and diffuse flow near the seafloor (c) erosion and channelling along permeable strata. In 2002, new observations and sampling were performed with submersible and ROV (1) on major thrusts along the boundary between the Kumano forearc basin domain and the accretionary wedge domain, (2) on a fault affecting the forearc (Kodaiba fault), (3) on mud volcanoes in the Kumano basin. In area (1) tsunami and seismic inversions indicate that the targeted thrusts are in the slip zone of the To-Nankai 1944 earthquakes. In this area, the largest seep zone, continuous over at least 2 km, coincides with the termination of a thrust trace, indicating local fluid channelling along the edge of the fault zone. Kodaiba fault is part of another splay fault system, which has both thrusting and strike-slip components and terminates westward into an en-echelon fold system. Strong seepage activity with abundant carbonates was found on a fold at the fault termination. One mud volcano, rooted in one of the en-echelon fold, has exceptionally high seepage activity compared with the others and thick carbonate crusts. These observations suggest that fluid expulsion along fault zones is most active at fault terminations and may be enhanced during fault initiation. Preliminary geochemical results indicate signatures differ between seep sites and suggests that the two fault systems tap in different sources.

Controls on intrusion of near-trench magmas of the Sanak-Baranof Belt, Alaska, during Paleogene ridge subduction, and consequences for forearc evolution

USGS Publications Warehouse

Kusky, Timothy M.; Bradley, Dwight C.; Donely, D. Thomas; Rowley, David; Haeussler, Peter J.

2003-01-01

A belt of Paleogene near-trench plutons known as the Sanak-Baranof belt intruded the southern Alaska convergent margin. A compilation of isotopic ages of these plutons shows that they range in age from 61 Ma in the west to ca. 50 Ma in the east. This migrating pulse of magmatism along the continental margin is consistent with North Pacific plate reconstructions that suggests the plutons were generated by migration of a trench-ridge-trench triple junction along the margin. On the Kenai Peninsula the regional lower greenschist metamorphic grade of the turbiditic host rocks, texture of the plutons, contact-metamorphic assemblage, and isotopic and fluid inclusion studies suggest that the plutons were emplaced at pressures of 1.5–3.0 kbars (5.2–10.5 km) into a part of the accretionary wedge with an ambient temperature of 210–300 °C. The presence of kyanite, garnet, and cordierite megacrysts in the plutons indicates that the melts were generated at a depth greater than 20 km and minimum temperature of 650 °C. These megacrysts are probably xenocrystic remnants of a restitic or contact metamorphic phase entrained by the melt during intrusion. However, it is also possible that they are primary magmatic phases crystallized from the peraluminous melt.Plutons of the Sanak-Baranof belt serve as time and strain markers separating kinematic regimes that predate and postdate ridge subduction. Pre-ridge subduction structures are interpreted to be related to the interaction between the leading oceanic plate and the Chugach terrane. These include regional thrust faults, NE-striking map-scale folds with associated axial planar foliation, type-1 mélanges, and an arrayof faults within the contact aureole indicating shortening largely accommodated by layer-parallel extension. Syn-ridge subduction features include the plutons, dikes, and ductile shear zones within contact aureoles with syn-kinematic metamorphic mineral growth and foliation development. Many of the studied plutons have sheeted margins and appear to have intruded along extensional jogs in margin-parallel strike-slip faults, whereas others form significant angles with the main faults and may have been influenced by minor faults of other orientations. Some of the plutons of the Sanak-Baranof belt have their long axes oriented parallel to faults of an orthorhombic fault set, implying that these faults may have provided a conduit for magma emplacement. This orthorhombic set of late faults is interpreted to have initially formed during the ridge subduction event, and continued to be active for a short time after passage of the triple junction. ENE-striking dextral faults of this orthorhombic fault system exhibit mutually crosscutting relationships with Eocene dikes related to ridge subduction, and mineralized strike-slip and normal faults of this system have yielded 40Ar/39Ar ages identical to near-trench intrusives related to ridge subduction. Movement on the orthorhombic fault system accommodated exhumation of deeper levels of the southern Alaska accretionary wedge, which is interpreted as a critical taper adjustment to subduction of younger oceanic lithosphere during ridge subduction. These faults therefore accommodate both deformation of the wedge and assisted emplacement of near-trench plutons. Structures that crosscut the plutons and aureoles include the orthorhombic fault set and dextral strike-slip faults, reflecting a new kinematic regime established after ridge subduction, during underthrusting of the trailing oceanic plate with new dextral-oblique convergence vectors with the overriding plate. The observation that the orthorhombic fault set both cuts and is cut by Eocene intrusives demonstrates the importance of these faults for magma emplacement in the forearc.A younger, ca. 35 Ma suite of plutons intrudes the Chugach terrane in the Prince William Sound region, and their intrusion geometry was strongly influenced by pre-existing faults developed during ridge subduction. The generation of these plutons may be related to the sudden northward migration of the triple junction at ca. 40–33 Ma, as the ridge was being subducted nearly parallel to the trench during this interval. These younger plutons are used to provide additional constraints on the structural evolution of the wedge. Late- to post-ridge subduction fabrics include a pressure solution cleavage and additional movement on the orthorhombic fault system. After triple junction migration, subduction of the trailing oceanic plate involved a significant component of dextral transpression and northward translation of the Chugach terrane. This change in kinematics is recorded by very late gouge-filled dextral faults in the late structures of the accretionary prism.

A Novel Characteristic Frequency Bands Extraction Method for Automatic Bearing Fault Diagnosis Based on Hilbert Huang Transform

PubMed Central

Yu, Xiao; Ding, Enjie; Chen, Chunxu; Liu, Xiaoming; Li, Li

2015-01-01

Because roller element bearings (REBs) failures cause unexpected machinery breakdowns, their fault diagnosis has attracted considerable research attention. Established fault feature extraction methods focus on statistical characteristics of the vibration signal, which is an approach that loses sight of the continuous waveform features. Considering this weakness, this article proposes a novel feature extraction method for frequency bands, named Window Marginal Spectrum Clustering (WMSC) to select salient features from the marginal spectrum of vibration signals by Hilbert–Huang Transform (HHT). In WMSC, a sliding window is used to divide an entire HHT marginal spectrum (HMS) into window spectrums, following which Rand Index (RI) criterion of clustering method is used to evaluate each window. The windows returning higher RI values are selected to construct characteristic frequency bands (CFBs). Next, a hybrid REBs fault diagnosis is constructed, termed by its elements, HHT-WMSC-SVM (support vector machines). The effectiveness of HHT-WMSC-SVM is validated by running series of experiments on REBs defect datasets from the Bearing Data Center of Case Western Reserve University (CWRU). The said test results evidence three major advantages of the novel method. First, the fault classification accuracy of the HHT-WMSC-SVM model is higher than that of HHT-SVM and ST-SVM, which is a method that combines statistical characteristics with SVM. Second, with Gauss white noise added to the original REBs defect dataset, the HHT-WMSC-SVM model maintains high classification accuracy, while the classification accuracy of ST-SVM and HHT-SVM models are significantly reduced. Third, fault classification accuracy by HHT-WMSC-SVM can exceed 95% under a Pmin range of 500–800 and a m range of 50–300 for REBs defect dataset, adding Gauss white noise at Signal Noise Ratio (SNR) = 5. Experimental results indicate that the proposed WMSC method yields a high REBs fault classification accuracy and a good performance in Gauss white noise reduction. PMID:26540059

Origin and late quaternary tectonism of a western Canadian continental shelf trough

NASA Astrophysics Data System (ADS)

Moslow, Thomas F.; Luternauer, John L.; Rohr, Kristin

1991-08-01

Analyses of high resolution and multi-channel seismic profiles from the central continental shelf of western Canada ascribe a late Quaternary glacial origin to large-scale troughs. Along the margins of Moresby Trough, one of three large-scale cross-shelf bathymetric depressions in Queen Charlotte Sound, seismic profiles within Quaternary sediments show a divergence of reflectors, thickening and folding of seismic units, and concavity of reflectors suggestive of drag. Compactional subsidence, growth faulting, and compaction faulting are also observed. Fault traces commonly terminate below the seabed. Deformation of Quaternary sediments due to faulting is plastic in nature and maximum offset of reflectors is 2.5 m. The observed Quaternary deformation appears to be a product of rapid deposition, loading and subsidence of late Quaternary sediment, which is unrelated to seismic activity. In addition, Quaternary faulting was probably activated by post-glacial loading and isostatic rebound of consolidated Tertiary strata along the margins of continental shelf troughs. The presence of mass movement (slump or debris flow) deposits overlying lithified Tertiary strata along the flanks of Moresby Trough provides the only evidence of seismic activity in the study area. The lack of a mud drape over these deposits implies a late Holocene age for the timing of their emplacement. The Quaternary troughs are incised into Tertiary-aged sedimentary fill of the Queen Charlotte basin. Previous workers had interpreted seafloor escarpments paralleling the trough margins to indicate that the location of Moresby Trough was controlled by renewed or continued activity on Tertiary-aged faults. A multi-channel seismic line across Moresby Trough shows that such an escarpment on the seafloor does not correlate to faults either in the Tertiary basin fill or the underlying basement. Tertiary reflectors are continuous underneath Moresby Trough; the seafloor escarpment is an erosional feature and was not created by reactivation of Tertiary structures. Trough erosion and subsequent fill (up to 175 m thick) are entirely of Quaternary age.

A Novel Characteristic Frequency Bands Extraction Method for Automatic Bearing Fault Diagnosis Based on Hilbert Huang Transform.

PubMed

Yu, Xiao; Ding, Enjie; Chen, Chunxu; Liu, Xiaoming; Li, Li

2015-11-03

Because roller element bearings (REBs) failures cause unexpected machinery breakdowns, their fault diagnosis has attracted considerable research attention. Established fault feature extraction methods focus on statistical characteristics of the vibration signal, which is an approach that loses sight of the continuous waveform features. Considering this weakness, this article proposes a novel feature extraction method for frequency bands, named Window Marginal Spectrum Clustering (WMSC) to select salient features from the marginal spectrum of vibration signals by Hilbert-Huang Transform (HHT). In WMSC, a sliding window is used to divide an entire HHT marginal spectrum (HMS) into window spectrums, following which Rand Index (RI) criterion of clustering method is used to evaluate each window. The windows returning higher RI values are selected to construct characteristic frequency bands (CFBs). Next, a hybrid REBs fault diagnosis is constructed, termed by its elements, HHT-WMSC-SVM (support vector machines). The effectiveness of HHT-WMSC-SVM is validated by running series of experiments on REBs defect datasets from the Bearing Data Center of Case Western Reserve University (CWRU). The said test results evidence three major advantages of the novel method. First, the fault classification accuracy of the HHT-WMSC-SVM model is higher than that of HHT-SVM and ST-SVM, which is a method that combines statistical characteristics with SVM. Second, with Gauss white noise added to the original REBs defect dataset, the HHT-WMSC-SVM model maintains high classification accuracy, while the classification accuracy of ST-SVM and HHT-SVM models are significantly reduced. Third, fault classification accuracy by HHT-WMSC-SVM can exceed 95% under a Pmin range of 500-800 and a m range of 50-300 for REBs defect dataset, adding Gauss white noise at Signal Noise Ratio (SNR) = 5. Experimental results indicate that the proposed WMSC method yields a high REBs fault classification accuracy and a good performance in Gauss white noise reduction.

Geologic map of the Strawberry Butte 7.5’ quadrangle, Meagher County, Montana

USGS Publications Warehouse

Reynolds, Mitchell W.; Brandt, Theodore R.

2017-06-19

The 7.5′ Strawberry Butte quadrangle in Meagher County, Montana near the southwest margin of the Little Belt Mountains, encompasses two sharply different geologic terranes.  The northern three-quarters of the quadrangle are underlain mainly by Paleoproterozoic granite gneiss, across which Middle Cambrian sedimentary rocks rest unconformably.  An ancestral valley of probable late Eocene age, eroded northwest across the granite gneiss terrane, is filled with Oligocene basalt and overlying Miocene and Oligocene sandstone, siltstone, tuffaceous siltstone, and conglomerate.  The southern quarter of the quadrangle is underlain principally by deformed Mesoproterozoic sedimentary rocks of the Newland Formation, which are intruded by Eocene biotite hornblende dacite dikes.  In this southern terrane, Tertiary strata are exposed only in a limited area near the southeast margin of the quadrangle.  The distinct terranes are juxtaposed along the Volcano Valley fault zone—a zone of recurrent crustal movement beginning possibly in Mesoproterozoic time and certainly established from Neoproterozoic–Early Cambrian to late Tertiary time.  Movement along the fault zone has included normal faulting, the southern terrane faulted down relative to the northern terrane, some reverse faulting as the southern terrane later moved up against the northern terrane, and lateral movement during which the southern terrane likely moved west relative to the northern terrane.  Near the eastern margin of the quadrangle, the Newland Formation is locally the host of stratabound sulfide mineralization adjacent to the fault zone; west along the fault zone across the remainder of the quadrangle are significant areas and bands of hematite and iron-silicate mineral concentrations related to apparent alteration of iron sulfides.  The map defines the distribution of a variety of surficial deposits, including the distribution of hematite-rich colluvium and iron-silicate boulders.  The southeast corner of the quadrangle is the site of active exploration and potential development for copper from the sulfide-bearing strata of the Newland Formation.

3D numerical simulations of multiphase continental rifting

NASA Astrophysics Data System (ADS)

Naliboff, J.; Glerum, A.; Brune, S.

2017-12-01

Observations of rifted margin architecture suggest continental breakup occurs through multiple phases of extension with distinct styles of deformation. The initial rifting stages are often characterized by slow extension rates and distributed normal faulting in the upper crust decoupled from deformation in the lower crust and mantle lithosphere. Further rifting marks a transition to higher extension rates and coupling between the crust and mantle lithosphere, with deformation typically focused along large-scale detachment faults. Significantly, recent detailed reconstructions and high-resolution 2D numerical simulations suggest that rather than remaining focused on a single long-lived detachment fault, deformation in this phase may progress toward lithospheric breakup through a complex process of fault interaction and development. The numerical simulations also suggest that an initial phase of distributed normal faulting can play a key role in the development of these complex fault networks and the resulting finite deformation patterns. Motivated by these findings, we will present 3D numerical simulations of continental rifting that examine the role of temporal increases in extension velocity on rifted margin structure. The numerical simulations are developed with the massively parallel finite-element code ASPECT. While originally designed to model mantle convection using advanced solvers and adaptive mesh refinement techniques, ASPECT has been extended to model visco-plastic deformation that combines a Drucker Prager yield criterion with non-linear dislocation and diffusion creep. To promote deformation localization, the internal friction angle and cohesion weaken as a function of accumulated plastic strain. Rather than prescribing a single zone of weakness to initiate deformation, an initial random perturbation of the plastic strain field combined with rapid strain weakening produces distributed normal faulting at relatively slow rates of extension in both 2D and 3D simulations. Our presentation will focus on both the numerical assumptions required to produce these results and variations in 3D rifted margin architecture arising from a transition from slow to rapid rates of extension.

Stratigraphy and structure along the Pensacola Arch/Conecuh Embayment margin in northwest Florida

DOE Office of Scientific and Technical Information (OSTI.GOV)

Duncan, J.G.

1993-03-01

Stratigraphic and structural analysis of deep borehole data along the Pensacola Arch/Conecuh Embayment margin in eastern Santa Rosa County, Florida reveals a northeast-trending basement normal fault that is downthrown to the northwest. The fault functioned as a border fault of a half-graben (or graben ) that developed during continental rifting of Pangea in the Late Triassic and Early Jurassic. The upthrown or horst block was a paleotopographic high that formed the southeastern boundary of the Middle to Late Jurassic Conecuh Embayment. A second, younger basement fault trends approximately perpendicular to the half-graben border fault. Late Triassic synrift continental sediments, depositedmore » on the downthrown block of the half-graben, pinch-out abruptly to the southeast pre-Mesozoic Suwannee Basin basement. The border fault is located approximately where the Triassic sedimentary wedge pinches out. Middle to Upper Jurassic drift-stage strata of the Conecuh embayment progressively onlap the post-rift unconformity toward the southeast. Upper Jurassic Smackover Formation carbonates and evaporites apparently overstep Triassic deposits and rest directly on Suwannee Basin quartzitic sandstone near their depositional limit at the Pensacola Arch. The Smackover Formation thins significantly toward the southeast in association with the Triassic pinch-out and half-graben border fault. The pinch-out trend of the Smackover Formation suggests a northeast-southwest orientation for the Triassic border fault and supports a horst-block origin for the Pensacola Arch.« less

Seismic Hazards of the Upper Mississippi Embayment

DTIC Science & Technology

1998-01-01

displacement of the Mississippi River; uplift of the Lake County uplift, Tiptonville dome, Blytheville arch; subsidence of Reelfoot Lake , Big Lake , and Lake St...slip faults within the Blytheville arch and western margin of the Reelfoot rift that are linked by the southwest dipping Reelfoot reverse fault. The...Bootheel lineament and back thrusts of the Reelfoot fault may also have slipped in 1811-12. Geomorphic effects of the 1811-12 sequence include

Crustal structure of the northern margin of the eastern Tien Shan, China, and its tectonic implications for the 1906 M~7.7 Manas earthquake

USGS Publications Warehouse

Wang, Chun-Yong; Yang, Zhu-En; Luo, Hai; Mooney, W.D.

2004-01-01

The Tien Shan orogenic belt is the most active intracontinental mountain belt in the world. We describe an 86-km-long N–S-trending deep seismic reflection profile (which passes through the southern Junggar basin) located on the northeastern Tien Shan piedmont. Two distinct anticlines beneath the northern margin of the Tien Shan are clearly imaged in the seismic section. In addition, we have imaged two detachment surfaces at depths of ∼7 and ∼16 km. The detachment surface at 16-km depth corresponds to the main detachment that converges with the steep angle reverse fault (the Junggar Southern Marginal Fault) on which the 1906 M~7.7 Manas earthquake occurred. A 12–14-km-thick sedimentary basin is imaged beneath the southern Junggar basin near Shihezi. The crust beneath the northern margin of the Tien Shan is 50–55-km thick, and decreases beneath the Junggar basin to 40–45-km thick. The crustal image of the deep seismic reflection profile is consistent with models derived from nearby seismic refraction data and Bouguer gravity anomalies in the same region. The faulting associated with the 1906 Manas earthquake also fits within the structural framework imaged by the seismic reflection profile. Present-day micro-seismicity shows a hypocentral depth-distribution between 5 and 35 km, with a peak at 20 km. We hypothesize that the 1906 Manas earthquake initiated at a depth of ∼20 km and propagated upwards, causing northward slip on the sub-horizontal detachments beneath the southern Junggar basin. Thus, in accord with regional geological mapping, the current shortening within the eastern Tien Shan is accommodated both by high-angle reverse faulting and detachment faulting that can be clearly imaged at depth in seismic reflection data.

Evidence for submarine landslides and continental slope erosion related to fault reactivation during the last glaciation offshore eastern Canada

NASA Astrophysics Data System (ADS)

Saint-Ange, F.; Campbell, C.; MacKillop, K.; Mosher, D. C.; Piper, D. J.; Roger, J.

2012-12-01

Many studies have proposed that reactivation of dormant faults during deglaciation is a source of neotectonic activity in glaciated regions, but few have demonstrated the relationship to submarine landslides. In this study, seabed morphology and shallow geology of the outer continental margin adjacent to the Charlie Gibbs Fracture Zone off Newfoundland, Canada was investigated for evidence of this relationship. The glacial history and morphology of the margin suggest that the entire continental shelf in the area, coincident with major continental crustal lineaments, was ice-covered during the Last glacial cycle, and transverse troughs delineate the paleo-icestream drainage patterns. A recent investigation of Notre Dame Trough revealed the existence of large sediment failures on the shelf. The current study investigates complex seafloor erosion and widespread mass transport deposition (MTD) on the continental slope seaward of Notre Dame Trough, using recently-acquired high resolution seismic reflection data and piston cores. The new data reveal that a trough mouth fan (TMF) is present on the slope seaward of Notre Dame Trough. The Notre Dame TMF is characterized by a succession of stacked debris flows, but does not show a lobate shape in plan view like other classic TMFs. Instead, the Notre Dame TMF has abruptly-truncated margins suggesting post-depositional failure and erosion of the fan deposits. Seismic reflection data show that the locations of the failures along the TMF margin are coincident with a set of shallow faults; however the current dataset does not image the deeper portion of the faults. On the upper slope immediately south of the TMF, a narrow and deeply incised canyon is located along-trend with the Notre Dame Trough. The location of this canyon appears to be controlled by a fault. Downslope from this canyon, along the southern margin of the TMF, a 25 km wide, flat-floored, U-shaped valley was eroded into a succession of stacked MTD-filled channels. Seismic stratigraphic analysis shows that the valley developed around the same time as the adjacent TMF, however, the valley morphology and evidence for repeated slope failure suggests that the processes responsible for its formation were different than the processes that formed the nearby TMF. Age control provided from piston cores suggest that the last major slope failure that contributed to valley formation probably occurred at ~29 ka. Geotechnical measurements from piston cores show slightly underconsolidated sediments. The results indicate that this part of the margin is more unstable than Orphan Basin and Labrador slope regions. Given the low factor of safety and the complex fault system, low energy earthquake from the surrounding area could be enough to potentially trigger landslides.

Questa Baseline and Premining Ground-Water Quality Investigation 18. Characterization of Brittle Structures in the Questa Caldera and Their Potential Influence on Bedrock Ground-Water Flow, Red River Valley, New Mexico

USGS Publications Warehouse

Caine, Jonathan S.

2006-01-01

This report presents a field-based characterization of fractured and faulted crystalline bedrock in the southern portion of the Questa caldera and its margin. The focus is (1) the identification and description of brittle geological structures and (2) speculation on the potential effects and controls that these structures might have on the potential fluxes of paleo to present-day ground water in relation to natural or mining-related metal and acid loads to surface and ground water. The entire study area is pervasively jointed with a few distinctive patterns such as orthogonal, oblique orthogonal, and conjugate joint sets. Joint intensity, the number of joints measured per unit line length, is high to extreme. Three types of fault zones are present that include partially silicified, low- and high-angle faults with well-developed damage zones and clay-rich cores and high-angle, unsilicified open faults. Conceptually, the joint networks can be thought of as providing the background porosity and permeability structure of the bedrock aquifer system. This background is cut by discrete entities such as the faults with clay-rich cores and open faults that may act as important hydrologic heterogeneities. The southern caldera margin runs parallel to the course of the Red River Valley, whose incision has left an extreme topographic gradient at high angles to the river. Many of the faults and fault intersections run parallel to this assumed hydraulic gradient; thus, these structures have great potential to provide paleo and present-day, discrete and anisotropic pathways for solute transport within the otherwise relatively low porosity and permeability bedrock background aquifer system. Although brittle fracture networks and faults are pervasive and complex, simple Darcy calculations are used to estimate the hydraulic conductivity and potential ground-water discharges of the bedrock aquifer, caldera margin, and other faults in order to gain insight into the potential contributions of these features to the ground-water and surface-water flow systems. These calculations show that, because all of these features are found along the Red River in the Cabin Springs-Columbine Park-Goat Hill fan area, their combined effect increases the probability that the bedrock aquifer ground-water flow system provides discharge to the Red River along this reach.

Evolution of the east-central San Jose del Cabo basin, Baja California Sur, Mexico

NASA Astrophysics Data System (ADS)

McTeague, M. S.; Umhoefer, P. J.; Schwennicke, T.; Ingle, J. C.; Cortes Martinez, M.

2006-12-01

The San Jose del Cabo basin at the southern tip of the Baja California peninsula records the early tectonic evolution of the west side of the Gulf of California. This study focused on the east central margin of the basin. The basal La Calera Formation unconformably overlies Cretaceous granite and consists of conglomerate, pebbly sandstone and conglomerate, and sandstone deposited in alluvial fans and fan-deltas. Deposition of the La Calera Formation was from ca. 9-14 Ma. The lower member of the Trinidad Formation was deposited beginning ca. 9-13 Ma and consists of sandstone, mudstone, and shelly mudstone deposited in nearshore and estuarine environments. These age estimates are based on sedimentation rates and foraminifera and coccoliths from the NN 11A nannozone (7.4 8.6 Ma, GTS 2004). The middle member of the Trinidad Formation consists of deeper water mudstones deposited by turbidity currents and suspension settling in a shelf to slope and conglomerates deposited by submarine debris flows on the shelf. The basin began earlier than previously thought. The oldest marine rocks are ca.9-13 Ma, while sedimentation on the east side began at ca. 9-14 Ma, synchronous with estimates of initiation of offset on the San Jose del Cabo fault. The Zapote fault is a down-to-the-east normal and sinistral-oblique fault that exposes a wedge of granite and older strata in the footwall to the west. The fault was active during sedimentation in the late Miocene and possibly later. The fault divides the study area into an eastern hanging wall subbasin and western footwall subbasin. The eastern subbasin formed an embayment in the eastern margin of the Cabo basin. A regional flooding surface (ca. 8 Ma) can be correlated across the fault that marks a major marine incursion. Depositional systems evolved rapidly from coarse-grained terrestrial systems to fine-grained marine and estuarine systems. The Cabo basin provides an excellent analogue for comparison with offshore basins, which are broadly similar with more faulting in lower strata and fewer or no faulting in upper strata. Offshore seismic data show older, deformed syn-rift strata in half graben overlain by younger, undeformed post-rift strata. The normal faults with 1-5 km spacing cut the basement rock and oldest sedimentary units. The eastern margin of the Cabo basin has older, growth strata cut by the Zapote fault that are overlain by simpler strata. Smaller scale normal faults in the Cabo basin are no longer active while the Cabo fault remains active.

Apatite fission-track evidence for regional exhumation in the subtropical Eocene, block faulting, and localized fluid flow in east-central Alaska

USGS Publications Warehouse

Dusel-Bacon, Cynthia; Bacon, Charles R.; O'Sullivan, Paul B.; Day, Warren C.

2016-01-01

The origin and antiquity of the subdued topography of the Yukon–Tanana Upland (YTU), the physiographic province between the Denali and Tintina faults, are unresolved questions in the geologic history of interior Alaska and adjacent Yukon. We present apatite fission-track (AFT) results for 33 samples from the 2300 km2 western Fortymile district in the YTU in Alaska and propose an exhumation model that is consistent with preservation of volcanic rocks in valleys that requires base level stability of several drainages since latest Cretaceous–Paleocene time. AFT thermochronology indicates widespread cooling below ∼110 °C at ∼56–47 Ma (early Eocene) and ∼44–36 Ma (middle Eocene). Samples with ∼33–27, ∼19, and ∼10 Ma AFT ages, obtained near a major northeast-trending fault zone, apparently reflect hydrothermal fluid flow. Uplift and erosion following ∼107 Ma magmatism exposed plutonic rocks to different extents in various crustal blocks by latest Cretaceous time. We interpret the Eocene AFT ages to suggest that higher elevations were eroded during the Paleogene subtropical climate of the subarctic, while base level remained essentially stable. Tertiary basins outboard of the YTU contain sediment that may account for the required >2 km of removed overburden that was not carried to the sea by the ancestral Yukon River system. We consider a climate driven explanation for the Eocene AFT ages to be most consistent with geologic constraints in concert with block faulting related to translation on the Denali and Tintina faults resulting from oblique subduction along the southern margin of Alaska.

Crustal structure and inferred extension mode in the northern margin of the South China Sea

NASA Astrophysics Data System (ADS)

Gao, J.; Wu, S.; McIntosh, K. D.; Mi, L.; Spence, G.

2016-12-01

Combining multi-channel seismic reflection and satellite gravity data, this study has investigated the crustal structure and magmatic activities of the northern South China Sea (SCS) margin. Results show that a broad continent-ocean transition zone (COT) with more than 140 km wide is characterized by extensive igneous intrusion/extrusion and hyper-extended continental crust in the northeastern SCS margin, a broader COT with 220-265 km wide is characterized by crustal thinning, rift depression, structural highs with igneous rock and perhaps a volcanic zone or a zone of tilted fault blocks at the distal edge in the mid-northern SCS margin, and a narrow COT with 65 km wide bounded seawards by a volcanic buried seamount is characterized by extremely hyper-extended continental crust in the northwestern SCS margin, where the remnant crust with less than 3 km thick is bounded by basin-bounding faults corresponding to an aborted rift below the Xisha Trough with a sub-parallel fossil ridge in the adjacent Northwest Sub-basin. Results from gravity modeling and seismic refraction data show that a high velocity layer (HVL) is present in the outer shelf and slope below extended continental crust in the eastern portion of the northern SCS margin and is thickest (up to 10 km) in the Dongsha Uplift where the HVL gradually thins to east and west below the lower slope and finally terminates at the Manila Trench and Baiyun sag of the Pearl River Mouth Basin. The magmatic intrusions/extrusions and HVL may be related to partial melting caused by decompression of passive, upwelling asthenosphere which resulted primarily in post-rifting underplating and magmatic emplacement or modification of the crust. The northern SCS margin is closer to those of the magma-poor margins than those of volcanic margins, but the aborted rift near the northwestern continental margin shows that there may be no obvious detachment fault like that in the Iberia-Newfoundland type margin. The symmetric aborted rift, broad hyper-extended continental crust, locally distributed HVL, and hotter mantle materials indicate that continental crust underwent stretching phase (pure-shear deformation), thinning phase and breakup followed by onset of seafloor spreading and the mantle-lithosphere may break up before crustal-necking in the northern South China Sea margin.

A shifting rift—Geophysical insights into the evolution of Rio Grande rift margins and the Embudo transfer zone near Taos, New Mexico

USGS Publications Warehouse

Grauch, V.J.S.; Bauer, Paul W.; Drenth, Benjamin J.; Kelson, Keith I.

2017-01-01

We present a detailed example of how a subbasin develops adjacent to a transfer zone in the Rio Grande rift. The Embudo transfer zone in the Rio Grande rift is considered one of the classic examples and has been used as the inspiration for several theoretical models. Despite this attention, the history of its development into a major rift structure is poorly known along its northern extent near Taos, New Mexico. Geologic evidence for all but its young rift history is concealed under Quaternary cover. We focus on understanding the pre-Quaternary evidence that is in the subsurface by integrating diverse pieces of geologic and geophysical information. As a result, we present a substantively new understanding of the tectonic configuration and evolution of the northern extent of the Embudo fault and its adjacent subbasin.We integrate geophysical, borehole, and geologic information to interpret the subsurface configuration of the rift margins formed by the Embudo and Sangre de Cristo faults and the geometry of the subbasin within the Taos embayment. Key features interpreted include (1) an imperfect D-shaped subbasin that slopes to the east and southeast, with the deepest point ∼2 km below the valley floor located northwest of Taos at ∼36° 26′N latitude and 105° 37′W longitude; (2) a concealed Embudo fault system that extends as much as 7 km wider than is mapped at the surface, wherein fault strands disrupt or truncate flows of Pliocene Servilleta Basalt and step down into the subbasin with a minimum of 1.8 km of vertical displacement; and (3) a similar, wider than expected (5–7 km) zone of stepped, west-down normal faults associated with the Sangre de Cristo range front fault.From the geophysical interpretations and subsurface models, we infer relations between faulting and flows of Pliocene Servilleta Basalt and older, buried basaltic rocks that, combined with geologic mapping, suggest a revised rift history involving shifts in the locus of fault activity as the Taos subbasin developed. We speculate that faults related to north-striking grabens at the end of Laramide time formed the first west-down master faults. The Embudo fault may have initiated in early Miocene southwest of the Taos region. Normal-oblique slip on these early fault strands likely transitioned in space and time to dominantly left-lateral slip as the Embudo fault propagated to the northeast. During and shortly after eruption of Servilleta Basalt, proto-Embudo fault strands were active along and parallel to the modern, NE-aligned Rio Pueblo de Taos, ∼4–7 km basinward of the modern, mapped Embudo fault zone. Faults along the northeastern subbasin margin had northwest strikes for most of the period of subbasin formation and were located ∼5–7 km basinward of the modern Sangre de Cristo fault. The locus of fault activity shifted to more northerly striking faults within 2 km of the modern range front sometime after Servilleta volcanism had ceased. The northerly faults may have linked with the northeasterly proto-Embudo faults at this time, concurrent with the development of N-striking Los Cordovas normal faults within the interior of the subbasin. By middle Pleistocene(?) time, the Los Cordovas faults had become inactive, and the linked Embudo–Sangre de Cristo fault system migrated to the south, to the modern range front.

The role of tectonic inheritance in the morphostructural evolution of the Galicia continental margin and adjacent abyssal plains from digital bathymetric model (DBM) analysis (NW Spain)

NASA Astrophysics Data System (ADS)

Maestro, A.; Jané, G.; Llave, E.; López-Martínez, J.; Bohoyo, F.; Druet, M.

2018-06-01

The identification of recent major tectonic structures in the Galicia continental margin and adjacent abyssal plains was carried out by means of a quantitative analysis of the linear structures having bathymetric expression on the seabed. It was possible to identify about 5800 lineaments throughout the entire study area, of approximately 271,500 km2. Most lineaments are located in the Charcot and Coruña highs, in the western sector of the Galicia Bank, in the area of the Marginal Platforms and in the northern sector of the margin. Analysis of the lineament orientations shows a predominant NE-SW direction and three relative maximum directions: NW-SE, E-W and N-S. The total length of the lineaments identified is over 44,000 km, with a mode around 5000 m and an average length of about 7800 m. In light of different tectonic studies undertaken in the northwestern margin of the Iberian Peninsula, we establish that the lineaments obtained from analysis of the digital bathymetric model of the Galicia continental margin and adjacent abyssal plains would correspond to fracture systems. In general, the orientation of lineaments corresponds to main faults, tectonic structures following the directions of ancient faults that resulted from late stages of the Variscan orogeny and Mesozoic extension phases related to Triassic rifting and Upper Jurassic to Early Cretaceous opening of the North Atlantic Ocean. The N-S convergence between Eurasian and African plates since Palaeogene times until the Miocene, and NW-SE convergence from Neogene to present, reactivated the Variscan and Mesozoic fault systems and related physiography.

The Ionian and Alfeo-Etna fault zones: New segments of an evolving plate boundary in the central Mediterranean Sea?

NASA Astrophysics Data System (ADS)

Polonia, A.; Torelli, L.; Artoni, A.; Carlini, M.; Faccenna, C.; Ferranti, L.; Gasperini, L.; Govers, R.; Klaeschen, D.; Monaco, C.; Neri, G.; Nijholt, N.; Orecchio, B.; Wortel, R.

2016-04-01

The Calabrian Arc is a narrow subduction-rollback system resulting from Africa/Eurasia plate convergence. While crustal shortening is taken up in the accretionary wedge, transtensive deformation accounts for margin segmentation along transverse lithospheric faults. One of these structures is the NNW-SSE transtensive fault system connecting the Alfeo seamount and the Etna volcano (Alfeo-Etna Fault, AEF). A second, NW-SE crustal discontinuity, the Ionian Fault (IF), separates two lobes of the CA subduction complex (Western and Eastern Lobes) and impinges on the Sicilian coasts south of the Messina Straits. Analysis of multichannel seismic reflection profiles shows that: 1) the IF and the AEF are transfer crustal tectonic features bounding a complex deformation zone, which produces the downthrown of the Western lobe along a set of transtensive fault strands; 2) during Pleistocene times, transtensive faulting reactivated structural boundaries inherited from the Mesozoic Tethyan domain which acted as thrust faults during the Messinian and Pliocene; and 3) the IF and the AEF, and locally the Malta escarpment, accommodate a recent tectonic event coeval and possibly linked to the Mt. Etna formation. Regional geodynamic models show that, whereas AEF and IF are neighboring fault systems, their individual roles are different. Faulting primarily resulting from the ESE retreat of the Ionian slab is expressed in the northwestern part of the IF. The AEF, on the other hand, is part of the overall dextral shear deformation, resulting from differences in Africa-Eurasia motion between the western and eastern sectors of the Tyrrhenian margin of northern Sicily, and accommodating diverging motions in the adjacent compartments, which results in rifting processes within the Western Lobe of the Calabrian Arc accretionary wedge. As such, it is primarily associated with Africa-Eurasia relative motion.

Active backstop faults in the Mentawai region of Sumatra, Indonesia, revealed by teleseismic broadband waveform modeling

NASA Astrophysics Data System (ADS)

Wang, Xin; Bradley, Kyle Edward; Wei, Shengji; Wu, Wenbo

2018-02-01

Two earthquake sequences that affected the Mentawai islands offshore of central Sumatra in 2005 (Mw 6.9) and 2009 (Mw 6.7) have been highlighted as evidence for active backthrusting of the Sumatran accretionary wedge. However, the geometry of the activated fault planes is not well resolved due to large uncertainties in the locations of the mainshocks and aftershocks. We refine the locations and focal mechanisms of medium size events (Mw > 4.5) of these two earthquake sequences through broadband waveform modeling. In addition to modeling the depth-phases for accurate centroid depths, we use teleseismic surface wave cross-correlation to precisely relocate the relative horizontal locations of the earthquakes. The refined catalog shows that the 2005 and 2009 "backthrust" sequences in Mentawai region actually occurred on steeply (∼60 degrees) landward-dipping faults (Masilo Fault Zone) that intersect the Sunda megathrust beneath the deepest part of the forearc basin, contradicting previous studies that inferred slip on a shallowly seaward-dipping backthrust. Static slip inversion on the newly-proposed fault fits the coseismic GPS offsets for the 2009 mainshock equally well as previous studies, but with a slip distribution more consistent with the mainshock centroid depth (∼20 km) constrained from teleseismic waveform inversion. Rupture of such steeply dipping reverse faults within the forearc crust is rare along the Sumatra-Java margin. We interpret these earthquakes as 'unsticking' of the Sumatran accretionary wedge along a backstop fault separating imbricated material from the stronger Sunda lithosphere. Alternatively, the reverse faults may have originated as pre-Miocene normal faults of the extended continental crust of the western Sunda margin. Our waveform modeling approach can be used to further refine global earthquake catalogs in order to clarify the geometries of active faults.

The southern Whidbey Island fault: An active structure in the Puget Lowland, Washington

USGS Publications Warehouse

Johnson, S.Y.; Potter, C.J.; Armentrout, J.M.; Miller, J.J.; Finn, C.; Weaver, C.S.

1996-01-01

Information from seismic-reflection profiles, outcrops, boreholes, and potential field surveys is used to interpret the structure and history of the southern Whidbey Island fault in the Puget Lowland of western Washington. This northwest-trending fault comprises a broad (as wide as 6-11 km), steep, northeast-dipping zone that includes several splays with inferred strike-slip, reverse, and thrust displacement. Transpressional deformation along the southern Whidbey Island fault is indicated by alongstrike variations in structural style and geometry, positive flower structure, local unconformities, out-of-plane displacements, and juxtaposition of correlative sedimentary units with different histories. The southern Whidbey Island fault represents a segment of a boundary between two major crustal blocks. The Cascade block to the northeast is floored by diverse assemblages of pre-Tertiary rocks; the Coast Range block to the southwest is floored by lower Eocene marine basaltic rocks of the Crescent Formation. The fault probably originated during the early Eocene as a dextral strike-slip fault along the eastern side of a continental-margin rift. Bending of the fault and transpressional deformation began during the late middle Eocene and continues to the present. Oblique convergence and clockwise rotation along the continental margin are the inferred driving forces for ongoing deformation. Evidence for Quaternary movement on the southern Whidbey Island fault includes (1) offset and disrupted upper Quaternary strata imaged on seismic-reflection profiles; (2) borehole data that suggests as much as 420 m of structural relief on the Tertiary-Quaternary boundary in the fault zone; (3) several meters of displacement along exposed faults in upper Quaternary sediments; (4) late Quaternary folds with limb dips of as much as ???9??; (5) large-scale liquefaction features in upper Quaternary sediments within the fault zone; and (6) minor historical seismicity. The southern Whidbey Island fault should be considered capable of generating large earthquakes (Ms ???7) and represents a potential seismic hazard to residents of the Puget Lowland.

Nonlinear dynamic failure process of tunnel-fault system in response to strong seismic event

NASA Astrophysics Data System (ADS)

Yang, Zhihua; Lan, Hengxing; Zhang, Yongshuang; Gao, Xing; Li, Langping

2013-03-01

Strong earthquakes and faults have significant effect on the stability capability of underground tunnel structures. This study used a 3-Dimensional Discrete Element model and the real records of ground motion in the Wenchuan earthquake to investigate the dynamic response of tunnel-fault system. The typical tunnel-fault system was composed of one planned railway tunnel and one seismically active fault. The discrete numerical model was prudentially calibrated by means of the comparison between the field survey and numerical results of ground motion. It was then used to examine the detailed quantitative information on the dynamic response characteristics of tunnel-fault system, including stress distribution, strain, vibration velocity and tunnel failure process. The intensive tunnel-fault interaction during seismic loading induces the dramatic stress redistribution and stress concentration in the intersection of tunnel and fault. The tunnel-fault system behavior is characterized by the complicated nonlinear dynamic failure process in response to a real strong seismic event. It can be qualitatively divided into 5 main stages in terms of its stress, strain and rupturing behaviors: (1) strain localization, (2) rupture initiation, (3) rupture acceleration, (4) spontaneous rupture growth and (5) stabilization. This study provides the insight into the further stability estimation of underground tunnel structures under the combined effect of strong earthquakes and faults.

Contrasting frictional behaviour of fault gouges containing Mg-rich phyllosilicates

NASA Astrophysics Data System (ADS)

Sanchez Roa, C.; Faulkner, D.; Jimenez Millan, J.; Nieto, F.

2015-12-01

The clay mineralogy of fault gouges has important implications on frictional properties and stability of fault planes. We studied the specific case of the Galera fault zone where fault gouges containing Mg-rich phyllosilicates appear as hydrothermal deposits related to high salinity fluids enriched in Mg2+. These deposits are dominated by sepiolite and palygorskite, both fibrous clay minerals with similar composition to Mg-smectite. The frictional strengths of sepiolite and palygorskite have not yet been determined, however, as they are part of the clay mineral group, it has been assumed that their frictional behaviour would be in line with platy clay minerals. We performed frictional sliding experiments on powdered pure standards and fault rocks in order to establish the frictional behaviour of sepiolite and palygorskite using a triaxial deformation apparatus with a servo-controlled axial loading system and fluid pressure pump. Friction coefficients for palygorskite and sepiolite as monomineralic samples were found to be 0.65 to 0.7 for dry experiments, and 0.45 to 0.5 for water-saturated experiments. Although these fibrous minerals are part of the phyllosilicates group, they show higher friction coefficients and their mechanical behaviour is less stable than platy clay minerals. This difference is a consequence of their stronger structural framework and the discontinuity of water layers. Our results present a contrast in mechanical behaviour between Mg-rich fibrous and platy clay minerals in fault gouges, where smectite is known to considerably reduce friction coefficients and to increase the stability of the fault plane leading to creeping processes. Transformations between saponite and sepiolite have been previously observed and could modify the deformation regime of a fault zone. Constraining the stability conditions and possible mineral reactions or transformations in fault gouges could help us understand the general role of clay minerals in fault stability.

ERTS-1 imagery of eastern Africa: A first look at the geological structure of selected areas

NASA Technical Reports Server (NTRS)

Mohr, P. A. (Principal Investigator)

1972-01-01

The author has identified the following significant results. Imagery of the African rift system resolves the major Cainozoic faults, zones of warping, and associated volcanism. It also clearly depicts the crystal grain of the Precambrian rocks where these are exposed. New structural features, or new properties of known features such as greater extent, continuity, and linearity are revealed by ERTS-1 imagery. This applies, for example, to the NE-SW fracture zones in Yemen, the Aswa mylonite zone at the northern end of the Western Rift, the Nandi fault of western Kenya, the linear faults of the Elgeyo escarpment in the Gregory Rift, and the hemibasins of warped Tertiary lavas on the Red Sea margin of Yemen, matching those of Ethiopian plateau-Afar margin. A tentative scheme is proposed, relating the effect on the pattern of Cainozoic faulting of the degree of obliquity to Precambrian structural trend. It is particularly noteworthy that, even where the Precambrian grain determines the rift faulting to be markedly oblique to the overall trend of the rift trough, for example, in central Lake Tanganyika, the width of the trough is not significantly increased. Some ground mapped lithological boundaries are obscure on ERTS-1 imagery.

The role of ocean circulation on methane hydrate stability and margin evolution

NASA Astrophysics Data System (ADS)

Hornbach, M. J.; Phrampus, B. J.; Ruppel, C. D.; Hart, P. E.

2012-12-01

For more than three decades, researchers have suggested a link between submarine gas hydrates and large (km-scale) continental margin slope failures (e.g. Carpenter 1980). Although several large submarine slope failures are co-located with methane hydrate deposits, a clear link between hydrates and slumping remains tenuous today (e.g. Maslin et al., 2003). Some studies suggest slope failures on continental margins are triggered by eustatic sea level lowering that destabilizes methane hydrates (e.g. Kayen and Lee, 1991; Paull et al, 1996). More recent studies by Dickens et al. (1995; 2001) postulate that a ~5 degree C increase in deep or intermediate ocean water temperature can, in theory, provide enough seafloor warming at continental margins to dissociate thousands of gigatons of methane hydrate into methane gas and water. This process, by elevating pore-fluid pressure, can lead to faulting, hydrofracture, and widespread slope failure (Dickens et al., 1995; Flemings et al., 2003; Hornbach et al., 2004). Similar ocean warming theories suggest methane hydrate dissociation as a probable cause of past and perhaps future ocean acidification events (Biastoch et al., 2011; Archer et al., 2004; Zachos et al., 1995). Here, using recently reprocessed 2D seismic data and 2D heat flow models, we suggest that recent (Holocene) shifts in ocean current flow directions along the edge of the Atlantic and Arctic margins are increasing ocean bottom temperatures by as much 8 degrees C, and in the process, destabilizing huge quantities (gigatons) of methane hydrate. Importantly, this mechanism for destabilizing methane hydrate requires no significant change in sea-level or average ocean temperature. We suggest the areas of active hydrate destabilization cover more than 10,000 km ^2, and occur, perhaps not coincidentally, in regions where some of the largest submarine slope failures exist. Forward models indicate we may be observing only the onset of large-scale contemporary methane hydrate destabilization at these sites and that this destabilization could continue for centuries. The results have significant implications for the global carbon budget, ocean acidification, ocean circulation, and the evolution of continental margins. The analysis presented here also provides a new method for constraining Holocene changes in intermediate ocean temperatures and demonstrates that only slight shifts in ocean current flow direction have a profound impact on both margin stability and the ocean carbon budget.

Effects of Fault Segmentation, Mechanical Interaction, and Structural Complexity on Earthquake-Generated Deformation

ERIC Educational Resources Information Center

Haddad, David Elias

2014-01-01

Earth's topographic surface forms an interface across which the geodynamic and geomorphic engines interact. This interaction is best observed along crustal margins where topography is created by active faulting and sculpted by geomorphic processes. Crustal deformation manifests as earthquakes at centennial to millennial timescales. Given that…

The Wallula fault and tectonic framework of south-central Washington, as interpreted from magnetic and gravity anomalies

USGS Publications Warehouse

Blakely, Richard J.; Sherrod, Brian; Weaver, Craig S.; Wells, Ray; Rohay, Alan C.

2014-01-01

The Yakima fold and thrust belt (YFTB) in central Washington has accommodated regional, mostly north-directed, deformation of the Cascadia backarc since prior to emplacement of Miocene flood basalt of the Columbia River Basalt Group (CRBG). The YFTB consists of two structural domains. Northern folds of the YFTB strike eastward and terminate at the western margin of a 20-mGal negative gravity anomaly, the Pasco gravity low, straddling the North American continental margin. Southern folds of the YFTB strike southeastward, form part of the Olympic–Wallowa lineament (OWL), and pass south of the Pasco gravity low as the Wallula fault zone. An upper crustal model based on gravity and magnetic anomalies suggests that the Pasco gravity low is caused in part by an 8-km-deep Tertiary basin, the Pasco sub-basin, abutting the continental margin and concealed beneath CRBG. The Pasco sub-basin is crossed by north-northwest-striking magnetic anomalies caused by dikes of the 8.5 Ma Ice Harbor Member of the CRBG. At their northern end, dikes connect with the eastern terminus of the Saddle Mountains thrust of the YFTB. At their southern end, dikes are disrupted by the Wallula fault zone. The episode of NE–SW extension that promoted Ice Harbor dike injection apparently involved strike-slip displacement on the Saddle Mountains and Wallula faults. The amount of lateral shear on the OWL impacts the level of seismic hazard in the Cascadia region. Ice Harbor dikes, as mapped with aeromagnetic data, are dextrally offset by the Wallula fault zone a total of 6.9 km. Assuming that dike offsets are tectonic in origin, the Wallula fault zone has experienced an average dextral shear of 0.8 mm/y since dike emplacement 8.5 Ma, consistent with right-lateral stream offsets observed at other locations along the OWL. Southeastward, the Wallula fault transfers strain to the north-striking Hite fault, the possible location of the M 5.7 Milton-Freewater earthquake in 1936.

Wavelet Filtering to Reduce Conservatism in Aeroservoelastic Robust Stability Margins

NASA Technical Reports Server (NTRS)

Brenner, Marty; Lind, Rick

1998-01-01

Wavelet analysis for filtering and system identification was used to improve the estimation of aeroservoelastic stability margins. The conservatism of the robust stability margins was reduced with parametric and nonparametric time-frequency analysis of flight data in the model validation process. Nonparametric wavelet processing of data was used to reduce the effects of external desirableness and unmodeled dynamics. Parametric estimates of modal stability were also extracted using the wavelet transform. Computation of robust stability margins for stability boundary prediction depends on uncertainty descriptions derived from the data for model validation. F-18 high Alpha Research Vehicle aeroservoelastic flight test data demonstrated improved robust stability prediction by extension of the stability boundary beyond the flight regime.

The Colorado front range: anatomy of a Laramide uplift

USGS Publications Warehouse

Kellogg, Karl; Bryant, Bruce; Reed, John C.

2004-01-01

Along a transect across the Front Range from Denver to the Blue River valley near Dillon, the trip explores the geologic framework and Laramide (Late Cretaceous to early Eocene) uplift history of this basement-cored mountain range. Specific items for discussion at various stops are (1) the sedimentary and structural record along the upturned eastern margin of the range, which contains several discontinuous, east-directed reverse faults; (2) the western structural margin of the range, which contains a minimum of 9 km of thrust overhang and is significantly different in structural style from the eastern margin; (3) mid- to late-Tertiary modifications to the western margin of the range from extensional faulting along the northern Rio Grande rift trend; (4) the thermal and uplift history of the range as revealed by apatite fission track analysis; (5) the Proterozoic basement of the range, including the significance of northeast-trending shear zones; and (6) the geologic setting of the Colorado mineral belt, formed during Laramide and mid-Tertiary igneous activity.

Wide-angle seismic data from the East Sicily margin: Imaging the deep structure of a Tethyan transform margin and the modern Calabria subduction lateral slab tear.

NASA Astrophysics Data System (ADS)

Dellong, D.; Klingelhoefer, F.; Kopp, H.; Gutscher, M. A.

2016-12-01

It is generally accepted that a STEP fault (Subduction Tear Edge Propagator) has accommodated the roll back of the Ionian Slab along the eastern Sicily Margin since 6 to 7 Ma. However the location of this lithospheric scale tear fault, and its surface expression is controversial. Constrain by numerous bathymetric imaging and shallow sub-surface multi-channels seismic (MCS) studies, variety of fault geometry was proposed. Moreover the role of the Malta Escarpment in this geodynamic system also remain the object of debates. It may be linked to the opening of the Ionian basin during a phase of strike-slip rifting since more than 180 Ma. Here we present the results of modelling of two wide-angle seismic profiles from the DIONYSUS survey (R/V Meteor, Oct. 2014). The first profile (DY-P3) was recorded by 25 Ocean- Bottom-Seismometers (OBS) and 3 land stations, and the second profile (DY-P1) by 52 OBS. Forward modelling of both profiles reveals a zone of abrupt crustal thinning from about 30 km below the Hyblean plateau and East-Sicily continental domain, to values of 8-15 km over a short lateral distance of 20-30 km. In the northern profile (DY-P3) the crust east of this abrupt thinning is of transitional thickness (15 km) and characterized by seismic velocities and velocity gradients similar to thinned continental crust. In the southern profile (DY-P1) this crust is 6-8 km thick, and the velocity gradients are close to those of oceanic crust. On this profile about 50-60 km eastward from the base of the Malta Escarpment, a lateral change of crustal velocities was modelled. Here a recent shallow transtensional deformation has been observed in MCS data at the position of this structure and linked to an elongated basin visible in the bathymetry and was linked to the STEP fault location. The results of the wide-angle seismic modelling suggest an ancient origin for the Malta Escarpment, formed as a transform margin during opening of the Ionian Basin about 180 Ma ago. The geometry of the modern day STEP fault is largely obscured in the northern profile because of the superposition of the structures with the ancient Tethyan transform Margin. In the southern wide-angle seismic profile these two structures are distinct and this allow us to conclude that the Malta Escarpment offshore SE Sicily has not been re-activated by the recent STEP-fault activity.

Seismic Modeling of the Alasehir Graben, Western Turkey

NASA Astrophysics Data System (ADS)

Gozde Okut, Nigar; Demirbag, Emin

2014-05-01

The purpose of this study is to develop a depth model to make synthetic seismic reflection sections, such as stacked and migrated sections with different velocity models. The study area is east-west trending Alasehir graben which is one of the most prominent structure in the western Anatolia, proved to have geothermal energy potential by researchers and exploration companies. Geological formations were taken from Alaşehir-1 borehole drilled by Turkish Petroleum Corporation (Çiftçi, 2007) and seismic interval velocities were taken from check-shots in the same borehole (Kolenoǧlu-Demircioǧlu, 2009). The most important structure is the master graben bounding fault (MGBF) in the southern margin of the Alasehir graben. Another main structure is the northern bounding fault called the antithetic fault of the MGBF with high angle normal fault characteristic. MGBF is a crucial contact between sedimentary cover and the metamorphic basement. From basement to the surface, five different stratigraphic units constitute graben fill . All the sedimentary units thicknesses get thinner from the southern margin to the northern margin of the Alasehir graben displaying roll-over geometry. A commercial seismic data software was used during modeling. In the first step, a 2D velocity/depth model was defined. Ray tracing was carried out with diffraction option to produce the reflection travel times. The reflection coefficients were calculated and wavelet shaping was carried out by means of band-pass filtering. Finally synthetic stacked section of the Alasehir graben was obtained. Then, migrated sections were generated with different velocity models. From interval velocities, average and RMS velocities were calculated for the formation entires to test how the general features of the geological model may change against different seismic models after the migration. Post-stack time migration method was used. Pseudo-velocity analysis was applied at selected CDP locations. In theory, seismic migration moves events to their correct spatial locations and collapse energy from diffractions back to their scattering points. This features of migration can be distinguished in the migrated sections. When interval velocities used, all the diffractions are removed and fault planes can be seen clearly. When average velocities used, MGBF plane extends to greater depths. Additionally, slope angles and locations of antithetic faults in the northern margin of the graben changes. When RMS velocities used, a migrated section was obtained for which to make an interpretation was quite hard, especially for the main structures along the northern margin and reflections related to formations.

Study of crustal structure and stretch mechanism of central continental shelf of northern South China Sea

NASA Astrophysics Data System (ADS)

Cao, J.; Xia, S.; Sun, J.; Wan, K.; Xu, H.

2017-12-01

Known as a significant region to study tectonic relationship between South China block and South China Sea (SCS) block and the evolution of rifted basin in continental margin, the continental shelf of northern SCS documents the evolution from continental splitting to seafloor spreading of SCS. To investigate crustal structure of central continental shelf in northern SCS, two wide-angle onshore-offshore seismic experiments and coincident multi-channel seismic (MCS) profiles were carried out across the onshore-offshore transitional zone in northern SCS, 2010 and 2012. A total of 34 stations consisted of ocean bottom seismometers, portable and permanent land stations were deployed during the survey. The two-dimensional precise crustal structure models of central continental shelf in northern SCS was constructed from onshore to offshore, and the stretching factors along the P-wave velocity models were calculated. The models reveal that South China block is a typical continental crust with a 30-32 km Moho depth, and a localized high-velocity anomaly in middle-lower crust under land area near Hong Kong was imaged, which may reflect magma underplating caused by subduction of paleo-Pacific plate in late Mesozoic. The littoral fault zone is composed of several parallel, high-angle, normal faults that mainly trend northeast to northeast-to-east and dip to the southeast with a large displacement, and the fault is divided into several segments separated by the northwest-trending faults. The shelf zone south of LFZ was consisted of a differential thinning upper and lower continental crust, which indicate stretch thinning of passive continent margin during the Cenozoic spreading of the SCS. The results appear to further confirm that the northern margin of SCS experienced a transition from active margin to passive one during late Mesozoic and Cenozoic.

Seismic Reflection Characteristic and Structure Unit Division of Nanwei Uplift in the Nansha Waters, South China Sea

NASA Astrophysics Data System (ADS)

Guo, L.; Zhan, W.; Yao, Y.

2016-12-01

Nanwei uplift is located in the continent-ocean transition zone at the southern margin of the South China Sea (SCS). It has the structural characteristics in typical passive margin models. Attributed to squeezing action, the anticline and faulted anticline structure were well developed since Oligocene. The development of organic reef and marine mudstone deposit indicated the drifting and subsidence stage. In this area, the structural evolution is not only related to the dynamic systems of rifting, basin spreading and expansion ending, but also to the collisions between different plates. Meanwhile, a large number of continental margin rifting basins with rich oil and gas resources developed in Nanwei uplift. It is meaningful to analyze the characteristics of seismic reflection waves. Also, two main structural unit were divided for studying the special structures and stratigraphic features in this paper. Two high-resolution single-channel seismic Line Nan-1 and Line Nan-2 in the Nansha Waters, acquired by the trial vessel "Shiyan 2" of the South China Sea Institute of Oceanology in 2013, is interpreted and analyzed in this study. The profiles show that there are a lot of normal fault half-garben systems and depressions in NE direction. Five seismic interfaces have been distinguished, named T0,T3,T4,T5 and Tg respectively. It corresponds to different regional unconformities in different geological age which indicated the characteristics of regional tectonics. On the basis of tectonic shape and previous geophysical data, it is believed that the Nanwei uplift zone is mainly composed of two structural units, the southern subsidence belt and northern buried volcanic uplift belt. The general range of zoning is also discussed in this paper. It is considered that the buried volcanic uplift belt mainly involved the marginal area along the southern ocean basin from 63-72 km wide in SE direction, the neighboring subsidence belt in rifting stage is parallel to the buried volcanic uplift belt with 57.5-128 km wide. In addition, the epicenter distributions of sporadic and larger than 4 magnitude earthquakes suggest that the entire Nanwei uplift is still a relatively stable tectonic activity zone, the crustal stability is good.

Recent Sedimentary Processes Along the Western Continental Margin of the South Korea Plateau, East Sea of Korea

NASA Astrophysics Data System (ADS)

Cukur, D.; Um, I. K.; Bahk, J. J.; Chun, J. H.; Lee, G. S.; Soo, K. G.; Horozal, S.; Kim, S. P.

2017-12-01

The continental margins of the marginal seas is largely shaped by a complex interplay of sediment transport processes directed both downslope and along-slope. Factors influence the sediment transport from shelf to the deep basin include: (i) seabed morphology, (ii) climate, (iii) sea level changes, (iv) slope stability, (v) oceanographic regime, and (vi) sediment sources. In order to understand the recent sedimentary processes along the western margin of the South Korea Plateau in the East Sea, we collected multiple geophysical datasets including the subbottom profiler and multibeam echosounder as well as geological sampling. Twelve echo types have been defined and interpreted as deposits formed by shallow marine, hemipelagic sedimentation, bottom currents, combined- (mass-movement/hemipelagic and hemipelagic/turbidites) and mass-movement-processes. Hemipelagic sedimentation, which is reflected as undisturbed layered sediments, appears to have been the primary sedimentary process throughout the study area. Two major slope-parallel channels appear to have acted as major conduits for turbidity currents from shallower shelf into the deep basins. Bottom current deposits, which is expressed as undulating seafloor morphology, are prevalent in the southern mid-slope at water depths between 250 to 450 m. Mass-transport deposits, consisting of chaotic seismic facies, occur in the upper and lower parts of the continental slope. Piston cores confirm the presence of MTDs that are characterized by mud clasts of variable size and shape. Multibeam bathymetry data show that these MTDs chiefly initiate on lower-slopes (400-600 m) where the gradient is up to 3°. In addition, subbottom profiles suggest the presence of numerous faults in close vicinity of headwall scarps; some are extending to the seafloor suggesting their recent activity. Earthquakes associated with tectonic activity are considered as the main triggering mechanism for these MTDs. Overall, the acoustic facies distribution shows that the sedimentary processes change downslope and differ within each physiographic province. In particular, the role of geological inheritance (i.e., structural folds and faults) on the geomorphology and sediment facies on the lower slopes appears to be quite important.

Distribution and Characteristics of Seafloor Seepage Features in the Active Margin Offshore of SW Taiwan

NASA Astrophysics Data System (ADS)

Chen, T. T.; Hsu, H. H.; Liu, C. S.; Su, C. C.; Paull, C. K.; Chen, Y. H.; Caress, D. W.; Gwiazda, R.; Lundsten, E. M.

2017-12-01

In the active margin offshore of southwest (SW) Taiwan, west-vergent imbricated thrusts, folds and dipping strata are the main structural features. This is also the area where gas hydrates are widely distributed beneath the seafloor. Fluids from deep strata may migrate upwards along porous dipping layers or faults and then vent out to form seafloor seepage features in many of the gas hydrate prospects. A joint survey was conducted in May 2017 using MBARI mapping AUV and miniROV to investigate the seafloor seepage features. Numerous comet-shaped depressions (CSD) are mapped along flanks of several anticlinal ridges, and four carbonate mounds around CSD are observed from the ultra-high-resolution (1-m lateral resolution) bathymetry data collected by AUV. Samples of the carbonate mounds were collected by the mini-ROV, and their mineral compositions contain dolomite and ankerite. The AUV collected chirp sonar profiles and previously collected surface ship multichannel seismic reflection profiles across these seafloor features show that potential fluid migration pathways connect free gas trapped below the base of gas hydrate stability zone and the seafloor in the vicinity of these features. Our study suggests that the CSD could be an indicator of seafloor seepage and may be distribution widely in the active margin setting.

Uplift Patterns in the Forearc of the Middle America Trench, Costa Rica: Implications for Mass Balance and Fore-arc Kinematics

NASA Astrophysics Data System (ADS)

Fisher, D. M.; Gardner, T. W.; Sak, P.; Marshall, J. S.; Protti, M.

2001-12-01

Uplift patterns along the Pacific Coast of Costa Rica provide insight into the balance of mass in the fore arc and depict an inner forearc that thickens nonuniformly at the expense of a subsiding margin wedge. Offshore, incoming seamounts and ridges on the subducting Cocos plate result in embayment of the trench axis and scarring that reflects downdropping of fault bounded blocks in the wake of subducting seamounts. The upper slope displays a regional unconformity that records late Tertiary subsidence and arcward displacement of the trench axis. Uplifted marine wavecut benches along the coast of Costa Rica, combined with analysis of fault populations, indicate that the inner fore arc has experienced a history that is in marked contrast to the subsidence and erosion observed in the margin wedge. Regionally, the inner forearc, from Osa to Nicaragua, has experienced uplift. One way to produce this regional uplift signal is movement on an out-of-sequence fault, or an active fault arcward of the frontal thrust. The longitudinal fault that marks the front of the Fila Costena may be an example of such a fault. Wood from a raised wavecut platform along this thrust front was radiocarbon dated at 5540 yrs. A balanced cross section of the Fila Costena indicates a detachment at a depth of ~ 2 km near the contact between upper slope sediments of the Terraba basin and the underlying basement of the margin wedge. This cross section also requires a >10 km of shortening accomplished by underthrusting of the outer fore arc. Crustal thickening by this mechanism could explain the dichotomy between uplift of the mountainous Fila Costena and Talamanca Ranges and subsidence of the slope apron offshore. Superimposed on this regional uplift of the Costa Rican coast is a pattern of faster uplift within fault-bounded blocks that lie inboard of incoming seamount chains. Offshore of Nicoya, the subducting plate displays two parallel ridges: a ridge coincident with the trace of the Coc-Naz- East Pacific Rise junction and a ridge defined by the Fisher Seamount chain. Inboard of both these bathymetric features there are raised wavecut benches and headlands that expose Tertiary upper slope sediments. Radiocarbon dates for these platforms indicate maximum uplift rates of ~ 6 mm yr-1 with slower uplift rates between these regions. The largest scar in the Costa Rican forearc is a trough oriented parallel to the Car-Coc relative plate motion vector that extends from the trench to near the coastline. Inboard of this scar is the Herradura block, a block that has experienceed more uplift than adjacent regions. A wavecut platform near the faulted margin of the Herradura block yields radiocarbon dates of 1010-1650 yrs and uplift rates of ~2.5 mm yr-1. The Osa Peninsula inboard of the Cocos Ridge records some of the fastest uplift rates measured in the Costa Rican fore arc based on marine sediments deposited around the margins of this peninsula and radiocarbon (AMS)-dated as 27000 to 49000 yrs. The most striking aspect of uplift patterns is that the local areas of fastest uplift in the forearc lie inboard of the areas with the most scarring and erosion in the margin wedge offshore. This pattern of uplift requires either underplating of seamounts beneath the inner forearc or enhanced shortening and crustal thickening inboard of subducting seamounts.

Environmental and ammonoid faunal changes related to Albian Bay of Biscay opening: Insights from the northern margin of the Basque-Cantabrian Basin

NASA Astrophysics Data System (ADS)

Agirrezabala, Luis M.; López-Horgue, Mikel A.

2017-12-01

The opening and ocean floor spreading of the Bay of Biscay began in the earliest Albian. The integrative study of the Albian sedimentary record and its ammonoid fauna (around 250 specimens) from the northern margin of the Basque-Cantabrian Basin indicates that environmental changes, occurred as a consequence of the Bay of Biscay opening, triggered significant ammonoid bioevents. Main bioevents are diversity changes in the ammonoid associations, occurrence of large forms (diameter up to 0.45 m) and the incursion of elements from other basins. Time-correlation of faulting pulses with ammonoid bioevents indicates that transtensive tectonics was ultimately the major control on the marine environmental conditions such as depth, sea bottom physiography, seaways, sedimentary systems and sea-water chemistry. The pulsating faulting during the Albian led to the increment of the subsidence rate, the deepening and widening of the margin and the progressive increase in the oceanic circulation between the margin and the nascent Bay of Biscay and North Atlantic. In addition, Albian synsedimentary faults constituted conduits for ascending magmas and hydrocarbon-rich hydrothermal fluids, which expelled to the seafloor, causing changes in the sediments, the sea-water chemistry (fertilization) and biota. The integration of sedimentological and palaeontological data has given the basis for a conceptual model of the ammonoid habitats.

A Comparative Study of the Electrical Structure of Circum Tibetan Plateau Orogenic Belts and its Tectonic Implications

NASA Astrophysics Data System (ADS)

Jin, Sheng; Zhang, Letian; Wei, Wenbo; Ye, Gaofeng; Jing, Jianen; Dong, Hao; Xie, Chengliang; Yin, Yaotian

2017-04-01

The Tibetan Plateau, as known as "roof of the world", was created through the on-going continent-continent collision between the Indian and Eurasian plates since 55 Ma. As the process continues, the plateau is growing both vertically and horizontally. The horizontal expansion of the plateau is blocked by the Yangtze block in the east, the Tarim block in the north, and the Ordos block in the northeast, and consequently lead to the formation of the circum Tibetan plateau orogenic belts. To better understand the mechanism behind this process, we conducted a comparative study by collecting 7 magnetotelluric (MT) profiles over the margins of the Tibetan plateau, namely, the INDEPTH 100, 700 and 800 lines in the southern Tibet, the INDEPTH 4000 and 5000 lines across the Altyn Tagh fault on the northern margin of the plateau, as well as other two profiles across the Haiyuan fault and the Longmenshan fault on the northeastern and eastern margins of the plateau deployed under the framework of project SinoProbe. The electrical features of the stable blocks surrounding the Tibetan plateau are generally resistive, while crustal conductive layers are found to be wide spread within the plateau. The southern margin of the Tibetan plateau is characterized by large scale underthrust of the Indian lithosphere beneath the plateau. This intense converging process created the thrust fault system distributed along the southern margin of the Tibetan plateau over 1000 km. Crustal conductive layers discovered in southern Tibet are generally associated with the southward crustal flow that originated from the lower crust within the plateau and exhumed along the thrust belts in the Himalayas. On the eastern margin of the Tibetan plateau, the electrical structures suggest that the Yangtze block wedged into the Tibetan lithosphere and caused decoupling between the crust and upper mantel. Large scale conductors discovered beneath the Songpan-Ganze block reflect that the eastward crustal flow was blocked and piled up along the eastern margin of the plateau due to the block of the Sichuan Basin, which further result in the uplift and expansion of the eastern Tibetan plateau. The northeastern and northern margins of the Tibetan plateau is bounded by large scale left-lateral strike-slip Haiyuan and Altyn Tagh faults. In these regions, the plateau interacts with the surrounding stable blocks in a way of oblique strike-slip. The deformation of the northern Tibetan lithosphere is dominated by crustal thickening, where no features of decoupling or large scale underthrusting were seen. Crustal conductors in these regions are generally not very well connected, which suggest the absence of crustal flow. Deep metamorphism fluids could be an alternative interpretation of the crustal conductors in these regions. * This work was jointly supported by the grants from Project SinoProbe-02-04 and National Natural Science Foundation of China (41404060).

Location of deeply buried, offshore Mesozoic transform fault along the western margin of the Gulf of Mexico inferred from gravity and magnetic data

NASA Astrophysics Data System (ADS)

Nguyen, L. C.; Mann, P.; Bird, D. E.

2013-12-01

Several workers have proposed that a Jurassic age, 500-km-long, right-lateral transform fault along the western margin of the Gulf of Mexico, possibly extending southward and onshore for another 500 km onto the isthmus area of southern Mexico, was formed as the ocean basin opened. This proposed transform fault plays a critical role in the most widely accepted tectonic model for the Mesozoic opening of the Gulf of Mexico by a ~40 degree, CCW rotation of the Yucatan block about a pole near southern Florida. Previously proposed names for the fault include the Tamaulipas-Chiapas transform fault and the Western Main transform fault for the offshore fault and the Orizaba transform fault for the southern, onland continuation of the fault into southern Mexico. There are few direct geologic or geophysical observations on the location or characteristics of the proposed offshore transform because it is buried beneath an over 10-km-thick sedimentary wedge along the continental margin of eastern Mexico. To better define this offshore fault, we identify a 500-km-long, 40-km-wide gravity anomaly, concentric with, and located about 60-70 km off the eastern coast of Mexico. Two east-west 200/1200-km-long gravity models constructed to cross the anomaly at right angles are parallel to existing multi-channel seismic lines with age-correlated stratigraphy. Both gravity models reveal an abrupt crustal thickness change beneath the gravity anomaly: from 27 km to 12 km over a distance of 65 km in the southern profile, and from 23 km to 16 km over a distance of 30 km in northern profile. The linearity of the anomaly in map view combined with the abrupt change in thickness inferred from gravity modeling is consistent with the tectonic origin of a right-lateral transform fault separating continental rocks of Mexico from Mesozoic seafloor produced by the opening of the Gulf of Mexico. Magnetic profiles were analyzed using a Werner depth-to-magnetic source technique, coincident with the gravity models, estimate the depth to top of crystalline basement for the northern (9 km) and southern (11 km) transects. Subsidence analysis along both transects shows that sedimentation rates sharply peaked during the Laramide orogeny in the latest Cretaceous-Eocene, but otherwise conform to steady thermal subsidence of oceanic crust in the deep Gulf of Mexico that formed during the Jurassic CCW rotation of the Yucatan block. The more precisely defined offshore fault aligns well with the onland right-lateral Orizaba transform fault of southern Mexico that is thought to have been active in Mesozoic time.

Porosity variations in and around normal fault zones: implications for fault seal and geomechanics

NASA Astrophysics Data System (ADS)

Healy, David; Neilson, Joyce; Farrell, Natalie; Timms, Nick; Wilson, Moyra

2015-04-01

Porosity forms the building blocks for permeability, exerts a significant influence on the acoustic response of rocks to elastic waves, and fundamentally influences rock strength. And yet, published studies of porosity around fault zones or in faulted rock are relatively rare, and are hugely dominated by those of fault zone permeability. We present new data from detailed studies of porosity variations around normal faults in sandstone and limestone. We have developed an integrated approach to porosity characterisation in faulted rock exploiting different techniques to understand variations in the data. From systematic samples taken across exposed normal faults in limestone (Malta) and sandstone (Scotland), we combine digital image analysis on thin sections (optical and electron microscopy), core plug analysis (He porosimetry) and mercury injection capillary pressures (MICP). Our sampling includes representative material from undeformed protoliths and fault rocks from the footwall and hanging wall. Fault-related porosity can produce anisotropic permeability with a 'fast' direction parallel to the slip vector in a sandstone-hosted normal fault. Undeformed sandstones in the same unit exhibit maximum permeability in a sub-horizontal direction parallel to lamination in dune-bedded sandstones. Fault-related deformation produces anisotropic pores and pore networks with long axes aligned sub-vertically and this controls the permeability anisotropy, even under confining pressures up to 100 MPa. Fault-related porosity also has interesting consequences for the elastic properties and velocity structure of normal fault zones. Relationships between texture, pore type and acoustic velocity have been well documented in undeformed limestone. We have extended this work to include the effects of faulting on carbonate textures, pore types and P- and S-wave velocities (Vp, Vs) using a suite of normal fault zones in Malta, with displacements ranging from 0.5 to 90 m. Our results show a clear lithofacies control on the Vp-porosity and the Vs-Vp relationships for faulted limestones. Using porosity patterns quantified in naturally deformed rocks we have modelled their effect on the mechanical stability of fluid-saturated fault zones in the subsurface. Poroelasticity theory predicts that variations in fluid pressure could influence fault stability. Anisotropic patterns of porosity in and around fault zones can - depending on their orientation and intensity - lead to an increase in fault stability in response to a rise in fluid pressure, and a decrease in fault stability for a drop in fluid pressure. These predictions are the exact opposite of the accepted role of effective stress in fault stability. Our work has provided new data on the spatial and statistical variation of porosity in fault zones. Traditionally considered as an isotropic and scalar value, porosity and pore networks are better considered as anisotropic and as scale-dependent statistical distributions. The geological processes controlling the evolution of porosity are complex. Quantifying patterns of porosity variation is an essential first step in a wider quest to better understand deformation processes in and around normal fault zones. Understanding porosity patterns will help us to make more useful predictive tools for all agencies involved in the study and management of fluids in the subsurface.

Fluid-injection and the mechanics of frictional stability of shale-bearing faults

NASA Astrophysics Data System (ADS)

Scuderi, Marco Maria; Collettini, Cristiano; Marone, Chris

2017-04-01

Fluid overpressure is one of the primary mechanisms for triggering tectonic fault slip and human-induced seismicity. This mechanism is appealing because fluids lubricate the fault and reduce the effective normal stress that holds the fault in place. However, current models of earthquake nucleation, based on rate- and state- friction, imply that stable sliding is favored by the increase of pore fluid pressure. Despite this apparent dilemma, there are a few studies on the role of fluid pressure in frictional stability under controlled, laboratory conditions. Here, we describe laboratory experiments on shale fault gouge, conducted in the double direct shear configuration in a true-triaxial machine. To characterize frictional stability and hydrological properties we performed three types of experiments: 1) stable sliding shear experiment to determine the material failure envelope resulting in fault strength of µ=0.28 and fault zone permeability (k 10-19m2); 2) velocity step experiments to determine the rate- and state- frictional properties, characterized by a velocity strengthening behavior with a negative rate parameter b, indicative of stable aseismic creep; 3) creep experiment to study fault slip evolution with increasing pore-fluid pressure. In these creep experiments fault slip history can be divided in three main stages: a) for low fluid pressure the fault is locked and undergoes compaction; b) with increasing fluid pressurization, we observe aseismic creep (i.e. v=0.0001 µm/s) associated with fault dilation, with maintained low permeability; c) As fluid pressure is further increased and we approach the failure criteria fault begins to accelerate, the dilation rate increases causing an increase in permeability. Following the first acceleration we document complex fault slip behavior characterized by periodic accelerations and decelerations with slip velocity that remains slow (i.e. v 200 µm/s), never approaching dynamic slip rates. Surprisingly, this complex slip behavior is associated with fault zone compaction and permeability increase as opposite to the dilation hardening mechanism that is usually invoked to quench the instability. We relate this complex fault slip behaviour to the interplay between fault weakening induced by fluid pressurization and the strong rate-strengthening behaviour of shales. Our data show that fault rheology and fault stability is controlled by the coupling between fluid pressure and rate- and state- friction parameters suggesting that their comprehensive characterization is fundamental for assessing the role of fluid pressure in natural and human induced earthquakes.

The shallow sedimentary and structural deformation in the southern Longmen Shan: constraints on the seismotectonics of the 2013 Lushan Mw6.7 Earthquake

NASA Astrophysics Data System (ADS)

Lu, R.; Xu, X.; He, D.; Suppe, J.

2017-12-01

On April 20, 2013, an unexpected Mw 6.7 earthquake occurred in Lushan County at the southern Longmen Shan, the eastern margin of the Tibetan Plateau. After this Lushan earthquake, whether the seismogenic fault is a high-angle or low-angle fault? The structural characteristics, attribution, and the seismotectonic model of this earthquake have many debates and problems. In this study, a high-resolution seismic reflection profile was combined with near-surface geological data, earthquake relocation and geodetic measurements, and a recent deep artificial seismic reflection profile to identify the active fault and seismotectonics of this earthquake. Three-dimensional imaging of the aftershocks was used to identify two planar faults that together form a y-shape (f1 and f2). Seismic interpretations suggest that the seismogenic fault f1 is a typical basement blind fault that did not penetrate into the overlying Mesozoic and Cenozoic units, and it is not a Shuangshi-Dachuan fault (F4) or the frontal Dayi buried fault (F6). Geodetic measurements suggest that the coseismic deformation is consistent with the geometry and kinematics of shear fault-bend folding (FBF). The history of tectonic evolution since the Paleozoic in Longmen Shan area also referred. There are three major detachments control the structural deformation of the upper crust in the Longmen Shan and Western Sichuan Basin, resulting in multiple superimposed deformation events. Deep seismic data indicate the syndepositional nature of fault f1 a preexisting normal fault older than the Triassic, which underwent positive inversion tectonics during the Late Cenozoic. A thrust fault f3 converges with f1 at a depth of approximately12 km with an accumulated slip 3.6 km. This 2013 Lushan earthquake triggered by blind faults is a hidden earthquake. Since the Late Cenozoic, with the strong and on-going compression of the Qinghai-Tibet Plateau to the Sichuan Basin, the early-period normal faults were activated after inversion and triggered Lushan earthquakes. Blind and reactivated faults increase the potential risk and uncertainty related to earthquakes in the eastern margin of the Tibetan Plateau.

Cenozoic evolution of the Socotra Island: opening of the Gulf of Aden

NASA Astrophysics Data System (ADS)

Razin, P.; Robin, C.; Serra Kiel, J.; Leroy, S.; Bellahsen, N.; Khanbari, K.

2009-12-01

A complete stratigraphic and geological map revision of the Tertiary of Socotra Island is undertaken in order to better characterize the geometry and the tecto-sedimentary evolution of the southern margin of the Gulf of Aden, and compare them with those of the conjugate northern margin in Oman. An increase of the rate of subsidence is recorded during the Late Eocene and is associated with a transgressive peak within carbonate platform deposits (Aydim Fm.). At the scale of the Arabian plate, the extent of this platform is reduced to the future rift area. This evolution of the platform system shows a modification of the sedimentary profiles, controlled by the beginning of the rifting. The syn-rift deposits of the Early Oligocene correspond to sub-reef carbonate platform facies (Ashawq Fm.). First, the throw of synsedimentary faults and the movements linked with differential subsidence are widely compensated by carbonate production which manages to maintain a platform profile. These movements are recorded by thickness variations, significant lateral variations in the platform facies and by a local inversion of sedimentary polarities controlled by the tilting of faulted blocks. Like on the northern margin, an acceleration of the extension process leads, during the Late Oligocene, to a collapse of the platform and to the creation of deep sub-basins with carbonate gravity-flow sedimentation. Marginal reef platforms keep growing at this stage on the structural highs and feed gravity-flow sedimentary systems. The sedimentation rate stays then relatively low in the basin, forming a complex topography of the margin, marked by a segmentation into numerous sub-basins more or less connected and separated by submarine escarpments marked by wedges of breccia deposits along active normal faults. In different points, these faults are sealed by sedimentary deposits characterized by progressive unconformities and onlap geometries on the fault escarpments. These geometries show the relatively short length of the phase of « stretching » of the continental crust. Around the end of the Early Miocene, the progradation of conglomerate fan-delta deposits locally results in the fill of the basins and shows a major phase of uplift. It is very rapidly followed by a new phase of subsidence which allows the preservation of thick fan-delta and equivalent reef platform complex unconformably overlying different units of the syn-rift and pre-rift sequences, or even the exhumed Proterozoic basement. This tectonic-sedimentary phase is interpreted as synchronous to the continental breakup and the onset of the OCT at the foot of the margin. The analogy with the phase of development of «sag basins» on the Atlantic margins has to be analyzed. This major uplift at the transition syn-rift/post-rift seems to be expressed symmetrically on both margins. These syn-OCT deposits are then uplifted and affected by late tilting events. However, the most recent deposits, probably Late Miocene to plio-Quaternary in age, have only been affected by small uplifts, unlike those of the Dhofar on the northern margin

Late Cretaceous through Cenozoic strike-slip tectonics of southwestern Alaska

USGS Publications Warehouse

Miller, M.L.; Bradley, D.C.; Bundtzen, T.K.; McClelland, W.

2002-01-01

New geologic mapping and geochronology show that margin-parallel strike-slip faults on the western limb of the southern Alaska orocline have experienced multiple episodes of dextral motion since ~100 Ma. These faults are on the upper plate of a subduction zone ~350-450 km inboard of the paleotrench. In southwestern Alaska, dextral displacement is 134 km on the Denali fault, at least 88-94 km on the Iditarod-Nixon Fork fault, and perhaps tens of kilometers on the Dishna River fault. The strike-slip regime coincided with Late Cretaceous sedimentation and then folding in the Kuskokwim basin, and with episodes of magmatism and mineralization at ~70, ~60, and ~30 Ma. No single driving mechanism can explain all of the ~95 million-year history of strike-slip faulting. Since ~40 Ma, the observed dextral sense of strike slip has run contrary to the sense of subduction obliquity. This may be explained by northward motion of the Pacific plate driving continental margin slivers into and/or around the oroclinal bend. From 44 to 66 Ma, oroclinal rotation, perhaps involving large-scale flexural slip, may have been accompanied by westward escape of crustal blocks along strike-slip faults. However, reconstructions of this period involve unproven assumptions about the identity of the subducting plate, the position of subducting ridges, and the exact timing of oroclinal bending, thus obscuring the driving mechanisms of strike slip. Prior to 66 Ma, oblique subduction is the most plausible driving mechanism for dextral strike slip. Cumulative displacement on all faults of the western limb of the orocline is at least 400 km, about half that on the eastern limb; this discrepancy might be explained by a combination of thrusting and unrecognized strike-slip faulting.

Northward expansion of Tibet beyond the Altyn Tagh Fault

NASA Astrophysics Data System (ADS)

Cunningham, D.; Zhang, J.; Yanfeng, L.; Vernon, R.

2017-12-01

For many tectonicists, the evolution of northern Tibet stops at the Altyn Tagh Fault (ATF). This study challenges that assumption. Structural field observations and remote sensing analysis indicate that the Sanweishan and Nanjieshan basement-cored ridges of the Archean Dunhuang Block, which interrupt the north Tibetan foreland directly north of the ATF, are bound and cut by an array of strike-slip, thrust and oblique-slip faults that have been active in the Quaternary and remain potentially active. The Sanweishan is essentially a SE-tilted block that is bound on its NW margin by a steep south-dipping thrust fault that has also accommodated sinistral strike-slip displacements. The Nanjieshan consists of parallel, but offset basement ridges that record NNW and SSE thrust displacements and sinistral strike-slip. Regional folds characterize the extreme eastern Nanjieshan perhaps above blind thrust faults which are emergent further west. At the surface, local fault reactivation of basement fabrics is an important control on the kinematics of deformation. Previously published magnetotelluric data for the region suggest that the major faults of the Sanweishan and Nanjieshan ultimately root to the south within conductive zones that merge into the ATF. Therefore, although the southern margin of the Dunhuang Block focuses significant deformation along the ATF, the adjacent cratonic basement to the north is also affected. Collectively, the ATF and structurally linked Sanweishan and Nanjieshan fault array represent a regional asymmetric half-flower structure that is dominated by non-strain partitioned sinistral transpression. The NW-trending Dengdengshan thrust fault array near Yumen City appears to define the northeastern limit of the Sanweishan-Nanjieshan block, which may be viewed regionally as the most northern, but early-stage expression of Tibetan Plateau growth into a reluctantly deforming, mechanically stiff Archean craton.

Fault distribution in the Precambrian basement of South Norway

NASA Astrophysics Data System (ADS)

Gabrielsen, Roy H.; Nystuen, Johan Petter; Olesen, Odleiv

2018-03-01

Mapping of the structural pattern by remote sensing methods (Landsat, SPOT, aerial photography, potential field data) and field study of selected structural elements shows that the cratonic basement of South Norway is strongly affected by a regular lineament pattern that encompasses fault swarms of different orientation, age, style, attitude and frequency. Albeit counting numerous fault and fracture populations, the faults are not evenly distributed and N-S to NNE-SSW/NNW-SSE and NE-SE/ENE-WSW-systems are spatially dominant. N-S to NNW-SSE structures can be traced underneath the Caledonian nappes to the Western Gneiss Region in western and central South Norway, emphasizing their ancient roots. Dyke swarms of different ages are found within most of these zones. Also, the Østfold, Oslo-Trondheim and the Mandal-Molde lineament zones coincide with trends of Sveconorwegian post-collision granites. We conclude that the N-S-trend includes the most ancient structural elements, and that the trend can be traced back to the Proterozoic (Svecofennian and Sveconorwegian) orogenic events. Some of the faults may have been active in Neoproterozoic times as marginal faults of rift basins at the western margin of Baltica. Remnants of such fault activity have survived in the cores of many of the faults belonging to this system. The ancient systems of lineaments were passively overridden by the Caledonian fold-and-thrust system and remained mostly, but note entirely inactive throughout the Sub-Cambrian peneplanation and the Caledonian orogenic collapse in the Silurian-Devonian. The system was reactivated in extension from Carboniferous times, particularly in the Permian with the formation of the Oslo Rift and parts of it remain active to the Present, albeit by decreasing extension and fault activity.

Oceanic transform faults: how and why do they form? (Invited)

NASA Astrophysics Data System (ADS)

Gerya, T.

2013-12-01

Oceanic transform faults at mid-ocean ridges are often considered to be the direct product of plate breakup process (cf. review by Gerya, 2012). In contrast, recent 3D thermomechanical numerical models suggest that transform faults are plate growth structures, which develop gradually on a timescale of few millions years (Gerya, 2010, 2013a,b). Four subsequent stages are predicted for the transition from rifting to spreading (Gerya, 2013b): (1) crustal rifting, (2) multiple spreading centers nucleation and propagation, (3) proto-transform faults initiation and rotation and (4) mature ridge-transform spreading. Geometry of the mature ridge-transform system is governed by geometrical requirements for simultaneous accretion and displacement of new plate material within two offset spreading centers connected by a sustaining rheologically weak transform fault. According to these requirements, the characteristic spreading-parallel orientation of oceanic transform faults is the only thermomechanically consistent steady state orientation. Comparison of modeling results with the Woodlark Basin suggests that the development of this incipient spreading region (Taylor et al., 2009) closely matches numerical predictions (Gerya, 2013b). Model reproduces well characteristic 'rounded' contours of the spreading centers as well as the presence of a remnant of the broken continental crustal bridge observed in the Woodlark basin. Similarly to the model, the Moresby (proto)transform terminates in the oceanic rather than in the continental crust. Transform margins and truncated tip of one spreading center present in the model are documented in nature. In addition, numerical experiments suggest that transform faults can develop gradually at mature linear mid-ocean ridges as the result of dynamical instability (Gerya, 2010). Boundary instability from asymmetric plate growth can spontaneously start in alternate directions along successive ridge sections; the resultant curved ridges become transform faults. Offsets along the transform faults change continuously with time by asymmetric plate growth and discontinuously by ridge jumps. The ridge instability is governed by rheological weakening of active fault structures. The instability is most efficient for slow to intermediate spreading rates, whereas ultraslow and (ultra)fast spreading rates tend to destabilize transform faults (Gerya, 2010; Püthe and Gerya, 2013) References Gerya, T. (2010) Dynamical instability produces transform faults at mid-ocean ridges. Science, 329, 1047-1050. Gerya, T. (2012) Origin and models of oceanic transform faults. Tectonophys., 522-523, 34-56 Gerya, T.V. (2013a) Three-dimensional thermomechanical modeling of oceanic spreading initiation and evolution. Phys. Earth Planet. Interiors, 214, 35-52. Gerya, T.V. (2013b) Initiation of transform faults at rifted continental margins: 3D petrological-thermomechanical modeling and comparison to the Woodlark Basin. Petrology, 21, 1-10. Püthe, C., Gerya, T.V. (2013) Dependence of mid-ocean ridge morphology on spreading rate in numerical 3-D models. Gondwana Res., DOI: http://dx.doi.org/10.1016/j.gr.2013.04.005 Taylor, B., Goodliffe, A., Martinez, F. (2009) Initiation of transform faults at rifted continental margins. Comptes Rendus Geosci., 341, 428-438.

Seismic imaging of a fractured gas hydrate system in the Krishna-Godavari Basin offshore India

USGS Publications Warehouse

Riedel, M.; Collett, T.S.; Kumar, P.; Sathe, A.V.; Cook, A.

2010-01-01

Gas hydrate was discovered in the Krishna-Godavari (KG) Basin during the India National Gas Hydrate Program (NGHP) Expedition 1 at Site NGHP-01-10 within a fractured clay-dominated sedimentary system. Logging-while-drilling (LWD), coring, and wire-line logging confirmed gas hydrate dominantly in fractures at four borehole sites spanning a 500m transect. Three-dimensional (3D) seismic data were subsequently used to image the fractured system and explain the occurrence of gas hydrate associated with the fractures. A system of two fault-sets was identified, part of a typical passive margin tectonic setting. The LWD-derived fracture network at Hole NGHP-01-10A is to some extent seen in the seismic data and was mapped using seismic coherency attributes. The fractured system around Site NGHP-01-10 extends over a triangular-shaped area of ~2.5 km2 defined using seismic attributes of the seafloor reflection, as well as " seismic sweetness" at the base of the gas hydrate occurrence zone. The triangular shaped area is also showing a polygonal (nearly hexagonal) fault pattern, distinct from other more rectangular fault patterns observed in the study area. The occurrence of gas hydrate at Site NGHP-01-10 is the result of a specific combination of tectonic fault orientations and the abundance of free gas migration from a deeper gas source. The triangular-shaped area of enriched gas hydrate occurrence is bound by two faults acting as migration conduits. Additionally, the fault-associated sediment deformation provides a possible migration pathway for the free gas from the deeper gas source into the gas hydrate stability zone. It is proposed that there are additional locations in the KG Basin with possible gas hydrate accumulation of similar tectonic conditions, and one such location was identified from the 3D seismic data ~6 km NW of Site NGHP-01-10. ?? 2010.

Lower Crustal Strength Controls on Melting and Serpentinization at Magma-Poor Margins: Potential Implications for the South Atlantic

NASA Astrophysics Data System (ADS)

Ros, Elena; Pérez-Gussinyé, Marta; Araújo, Mario; Thoaldo Romeiro, Marco; Andrés-Martínez, Miguel; Morgan, Jason P.

2017-12-01

Rifted continental margins may present a predominantly magmatic continent-ocean transition (COT), or one characterized by large exposures of serpentinized mantle. In this study we use numerical modeling to show the importance of the lower crustal strength in controlling the amount and onset of melting and serpentinization during rifting. We propose that the relative timing between both events controls the nature of the COT. Numerical experiments for half-extension velocities <=10 mm/yr suggest there is a genetic link between margin tectonic style and COT nature that strongly depends on the lower crustal strength. Our results imply that very slow extension velocities (< 5 mm/yr) and a strong lower crust lead to margins characterized by large oceanward dipping faults, strong syn-rift subsidence and abrupt crustal tapering beneath the continental shelf. These margins can be either narrow symmetric or asymmetric and present a COT with exhumed serpentinized mantle underlain by some magmatic products. In contrast, a weak lower crust promotes margins with a gentle crustal tapering, small faults dipping both ocean- and landward and small syn-rift subsidence. Their COT is predominantly magmatic at any ultra-slow extension velocity and perhaps underlain by some serpentinized mantle. These margins can also be either symmetric or asymmetric. Our models predict that magmatic underplating mostly underlies the wide margin at weak asymmetric conjugates, whereas the wide margin is mainly underlain by serpentinized mantle at strong asymmetric margins. Based on this conceptual template, we propose different natures for the COTs in the South Atlantic.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Barber, A.J.; Tjokrosapoetro, S.; Charlton, T.R.

In Timor, eastern Indonesia, where the northern margin of the Australian continent is colliding with the Banda Arc, Australian continental margin sediments are being incorporated into an imbricate wedge, which passes northward into a foreland fold and thrust belt. Field mapping in Timor has shown that scale clays, containing irregularly shaped or phacoidal blocks (up to several meters long) and composed of a wide range of lithologies derived from local stratigraphic units, occur in three environments: along wrench faults, as crosscutting shale diapirs, and associated with mud volcanoes. A model is proposed linking these phenomena. Shales become overpressured as amore » result of overthrusting; this overpressure is released along vertical wrench faults, which cut through the overthrust units; overpressured shales containing blocks of consolidated units rise along the fault zones as shale diapirs; and escaping water, oil, and gas construct mud volcanoes at the surface. 6 figures, 1 table.« less

Late cretaceous extensional tectonics and associated igneous activity on the northern margin of the Gulf of Mexico Basin

NASA Technical Reports Server (NTRS)

Bowen, R. L.; Sundeen, D. A.

1985-01-01

Major, dominantly compressional, orogenic episodes (Taconic, Acadian, Alleghenian) affected eastern North America during the Paleozoic. During the Mesozoic, in contrast, this same region was principally affected by epeirogenic and extensional tectonism; one episode of comparatively more intense tectonic activity involving extensive faulting, uplift, sedimentation, intrusion and effusion produced the Newark Series of eposits and fault block phenomena. This event, termed the Palisades Disturbance, took place during the Late Triassic - Earliest Jurassic. The authors document a comparable extensional tectonic-igneous event occurring during the Late Cretaceous (Early Gulfian; Cenomanian-Santonian) along the southern margin of the cratonic platform from Arkansas to Georgia.

High sedimentation rates and thrust fault modulation: Insights from ocean drilling offshore the St. Elias Mountains, southern Alaska

NASA Astrophysics Data System (ADS)

Worthington, Lindsay L.; Daigle, Hugh; Clary, Wesley A.; Gulick, Sean P. S.; Montelli, Aleksandr

2018-02-01

The southern Alaskan margin offshore the St. Elias Mountains has experienced the highest recorded offshore sediment accumulation rates globally. Combined with high uplift rates, active convergence and extensive temperate glaciation, the margin provides a superb setting for evaluating competing influences of tectonic and surface processes on orogen development. We correlate results from Integrated Ocean Drilling Program (IODP) Expedition 341 Sites U1420 and U1421 with regional seismic data to determine the spatial and temporal evolution of the Pamplona Zone fold-thrust belt that forms the offshore St. Elias deformation front on the continental shelf. Our mapping shows that the pattern of active faulting changed from distributed across the shelf to localized away from the primary glacial depocenter over ∼300-780 kyrs, following an order-of-magnitude increase in sediment accumulation rates. Simple Coulomb stress calculations show that the suppression of faulting is partially controlled by the change in sediment accumulation rates which created a differential pore pressure regime between the underlying, faulted strata and the overlying, undeformed sediments.

Laramide basin CSI: Comprehensive stratigraphic investigations of Paleogene sediments in the Colorado Headwaters Basin, north-central Colorado

USGS Publications Warehouse

Dechesne, Marieke; Cole, James Channing; Trexler, James H.; Cashman, Patricia; Peterson, Christopher D

2013-01-01

The Paleogene sedimentary deposits of the Colorado Headwaters Basin provide a detailed proxy record of regional deformation and basin subsidence during the Laramide orogeny in north-central Colorado and southern Wyoming. This field trip presents extensive evidence from sedimentology, stratigraphy, structure, palynology, and isotope geochronology that shows a complex history that is markedly different from other Laramide synorogenic basins in the vicinity.We show that the basin area was deformed by faulting and folding before, during, and after deposition of the Paleogene rocks. Internal unconformities have been identified that further reflect the interaction of deformation, subsidence, and sedimentation. Uplift of Proterozoic basement blocks that make up the surrounding mountain ranges today occurred late in basin history. Evidence is given to reinterpret the Independence Mountain uplift as the result of significant normal faulting (not thrusting), probably in middle Tertiary time.While the Denver and Cheyenne Basins to the east were subsiding and accumulating sediment during Late Cretaceous time, the Colorado Headwaters Basin region was experiencing vertical uplift and erosion. At least 1200 m of the upper part of the marine Upper Cretaceous Pierre Shale was regionally removed, along with Fox Hills Sandstone shoreline deposits of the receding Interior Seaway as well as any Laramie Formation–type continental deposits. Subsidence did not begin in the Colorado Headwaters Basin until after 60.5 Ma, when coarse, chaotic, debris-flow deposits of the Paleocene Windy Gap Volcanic Member of the Middle Park Formation began to accumulate along the southern basin margin. These volcaniclastic conglomerate deposits were derived from local, mafic-alkalic volcanic sources (and transitory deposits in the drainage basin), and were rapidly transported into a deep lake system by sediment gravity currents. The southern part of the basin subsided rapidly (roughly 750–1000 m/m.y.) and the drainage system delivered increasing proportions of arkosic debris from uplifted Proterozoic basement and more intermediate-composition volcanic-porphyry materials from central Colorado sources.Other margins of the Colorado Headwaters Basin subsided at slightly different times. Subsidence was preceded by variable amounts of gentle tilting and localized block-fault uplifts. The north-central part of the basin that was least-eroded in early Paleocene time was structurally inverted and became the locus of greatest subsidence during later Paleocene-Eocene time. Middle Paleocene coal-mires formed in the topographically lowest eastern part of the basin, but the basin center migrated to the western side by Eocene time when coal was deposited in the Coalmont district. In between, persistent lakes of variable depths characterized the central basin area, as evidenced by well-preserved deltaic facies.Fault-fold deformation within the Colorado Headwaters Basin strongly affected the Paleocene fluvial-lacustrine deposits, as reflected in the steep limbs of anticline-syncline pairs within the McCallum fold belt and the steep margins of the Breccia Spoon syncline. Slivers of Proterozoic basement rock were also elevated on steep reverse faults in late Paleocene time along the Delaney Butte–Sheep Mountain–Boettcher Ridge structure. Eocene deposits, by and large, are only gently folded within the Colorado Headwaters Basin and thus reflect a change in deformation history.The Paleogene deposits of the Colorado Headwaters Basin today represent only a fragment of the original extent of the depositional basin. Basal, coarse conglomerate deposits that suggest proximity to an active basin margin are relatively rare and are limited to the southern and northwestern margins of the relict basin. The northeastern margin of the preserved Paleogene section is conspicuously fine-grained, which indicates that any contemporaneous marginal uplift was far removed from the current extent of preserved fluvial-lacustrine sediments. The conspicuous basement uplifts of Proterozoic rock that flank the current relict Paleogene basin deposits are largely post-middle Eocene in age and are not associated with any Laramide synuplift fluvial deposits.The east-west–trending Independence Mountain fault system that truncates the Colorado Headwaters Basin on the north with an uplifted Proterozoic basement block is reinterpreted in this report. Numerous prior analyses had concluded that the fault was a low-angle, south-directed Laramide thrust that overlapped the northern margin of the basin. We conclude instead that the fault is more likely a Neogene normal fault that truncates all prior structure and belongs to a family of sub-parallel west-northwest–trending normal faults that offset upper Oligocene-Miocene fluvial deposits of the Browns Park–North Park Formations.

Continentward-Dipping Normal Faults, Boudinage and Ductile Shear at Rifted Passive Margins

NASA Astrophysics Data System (ADS)

Clerc, C. N.; Ringenbach, J. C.; Jolivet, L.; Ballard, J. F.

2017-12-01

Deep structures resulting from the rifting of the continental crust are now well imaged by seismic profiles. We present a series of recent industrial profiles that allow the identification of various rift-related geological processes such as crustal boudinage, ductile shear of the base of the crust and low-angle detachment faulting. Along both magma-rich and magma-poor rifted margins, we observe clear indications of ductile deformation of the deep continental crust. Large-scale shallow dipping shear zones are identified with a top-to-the-continent sense of shear. This sense of shear is consistent with the activity of the Continentward-Dipping Normal Faults (CDNF) that accommodate the extension in the upper crust. This pattern is responsible for an oceanward migration of the deformation and of the associated syn-tectonic deposits (sediments and/or volcanics). We discuss the origin of the Continentward-Dipping Normal Faults (CDNF) and investigate their implications and the effect of sediment thermal blanketing on crustal rheology. In some cases, low-angle shear zones define an anastomosed pattern that delineates boudin-like structures that seem to control the position and dip of upper crustal normal faults. We present some of the most striking examples from several locations (Uruguay, West Africa, South China Sea…), and discuss their rifting histories that differ from the classical models of oceanward-dipping normal faults.

Structure Of The Elevated Precambrian Terranes Rising Above The Brahmaputra Plains In Northeastern India.

NASA Astrophysics Data System (ADS)

Gaur, V. K.; Hazarika, N. K.; Mitra, S.; Priestley, K.

2007-12-01

We present new evidence for a thinner crust beneath most of the Shillong plateau as well as its northeast extension in Mikir Hills of northeastern India.Both these Precambrian terranes rise above the Brahmaputra plains whose crust is thicker in comparison by atleast 4~km. Although Bouger gravity over the Mikir Hills still remains to be determined, its near zero value over the ~1 km high plateau and the near normal upper mantle beneath the region, require that these elevated terranes must have been uplifted between reversed faults and continue to be supported by them under compression. The southern edge of the Shillong plateau is indeed marked by the prominent Dauki fault which swerves northeastward at the south eastern margin of the plateau to merge with the Naga thrusts that bound the Mikir Hills on the east. A similar fault bounding the plateau on the north as hypothesized by Bilham et al (2000) -the Oldham fault- is therfore required to swerve northeastward near the northeastern margin of the plateau to demarcate the Mikir Hills from the thicker crust Brahmaputra plains to its north and west. This could be explained by a strike slip offset of the Oldham fault caused by the as yet obsure but active tectonics of the NNW trending Kopili lineament that ensues from the inflexion in the Dauki-Naga thrust fault system.

Robust Flutter Margin Analysis that Incorporates Flight Data

NASA Technical Reports Server (NTRS)

Lind, Rick; Brenner, Martin J.

1998-01-01

An approach for computing worst-case flutter margins has been formulated in a robust stability framework. Uncertainty operators are included with a linear model to describe modeling errors and flight variations. The structured singular value, mu, computes a stability margin that directly accounts for these uncertainties. This approach introduces a new method of computing flutter margins and an associated new parameter for describing these margins. The mu margins are robust margins that indicate worst-case stability estimates with respect to the defined uncertainty. Worst-case flutter margins are computed for the F/A-18 Systems Research Aircraft using uncertainty sets generated by flight data analysis. The robust margins demonstrate flight conditions for flutter may lie closer to the flight envelope than previously estimated by p-k analysis.

Toward self-consistent tectono-magmatic numerical model of rift-to-ridge transition

NASA Astrophysics Data System (ADS)

Gerya, Taras; Bercovici, David; Liao, Jie

2017-04-01

Natural data from modern and ancient lithospheric extension systems suggest three-dimensional (3D) character of deformation and complex relationship between magmatism and tectonics during the entire rift-to-ridge transition. Therefore, self-consistent high-resolution 3D magmatic-thermomechanical numerical approaches stand as a minimum complexity requirement for modeling and understanding of this transition. Here we present results from our new high-resolution 3D finite-difference marker-in-cell rift-to-ridge models, which account for magmatic accretion of the crust and use non-linear strain-weakened visco-plastic rheology of rocks that couples brittle/plastic failure and ductile damage caused by grain size reduction. Numerical experiments suggest that nucleation of rifting and ridge-transform patterns are decoupled in both space and time. At intermediate stages, two patterns can coexist and interact, which triggers development of detachment faults, failed rift arms, hyper-extended margins and oblique proto-transforms. En echelon rift patterns typically develop in the brittle upper-middle crust whereas proto-ridge and proto-transform structures nucleate in the lithospheric mantle. These deep proto-structures propagate upward, inter-connect and rotate toward a mature orthogonal ridge-transform patterns on the timescale of millions years during incipient thermal-magmatic accretion of the new oceanic-like lithosphere. Ductile damage of the extending lithospheric mantle caused by grain size reduction assisted by Zenner pinning plays critical role in rift-to-ridge transition by stabilizing detachment faults and transform structures. Numerical results compare well with observations from incipient spreading regions and passive continental margins.

Rifting and reactivation of a Cretaceous structural belt at the northern margin of the South China Sea

NASA Astrophysics Data System (ADS)

Nanni, Ugo; Pubellier, Manuel; Chan, Lung Sang; Sewell, Roderick J.

2017-04-01

The Tiu Tang Lung Fault, Hong Kong Special Administrative Region - China, is located on the northern stretched continental margin of the South China Sea. Along this fault, Middle Jurassic volcanic rocks of the Tai Mo Shan Formation are tectonically juxtaposed on Lower Cretaceous sedimentary rocks of the Pat Sin Leng Formation. Both extensional detachments and compressional features are observed and various genetic strain configurations are proposed for the Tiu Tang Lung Fault with implications for understanding the dynamics of the pre-South China Sea rifting during the Cretaceous. We have identified tilted bedding planes in the continental deposits of the Pat Sin Leng Formation which can be related to Early Cretaceous syn-extensional deposition. A mid-Cretaceous penetrative top-to-the-south to top-to-the-west shear fabric is also observed and serves as an indicator of the strain pattern. This deformation is expressed by cleavages, schistosity, S/C fabrics, kink-folds, phacoids and stretched pebbles at both a macroscopic and microscopic scale. Cleavages and bedding are generally sub-parallel to the local shear orientation. The whole sedimentary pile is crosscut by Cenozoic N70 and N150 normal faults. These constraints, together with previous fission track, seismic and structural data, allow us to reinterpret the kinematics of this domain during syn-orogenic to syn-extensional periods. The observed top-to-the-south thrusting event is coeval with NE-SW strike-slip sinistral fault movement. Subsequent N-S extension can be correlated with South China Sea rifting from Eocene to Oligocene. These observations reveal a polyphase history associated with continental margin inversion which witnessed localized extension on previous compressional structures.

Deep structure of the Texas Gulf passive margin and its Ouachita-Precambrian basement: Results of the COCORP San Marcos arch survey

DOE Office of Scientific and Technical Information (OSTI.GOV)

Culotta, R.; Latham, T.; Oliver, J.

1992-02-01

This COCORP deep seismic survey provides a comprehensive image of the southeast-Texas part of the Gulf passive margin and its accreted Ouachita arc foundation. Beneath the updip limit of the Cenozoic sediment wedge, a prominent antiformal structure is imaged within the interior zone of the buried late Paleozoic Ouachita orogen. The structure appears to involve Precambrian Grenville basement. The crest of the antiform is coincident with the Cretaceous-Tertiary Luling-Mexia-Talco fault zone. Some of these faults dip to the northwest, counter to the general regional pattern of down-to-the-basin faulting, and appear to sole into the top of the antiform, suggesting thatmore » the Ouachita structure has been reactivated as a hingeline to the subsiding passive margin. The antiform may be tied via this fault system and the Ouachita gravity gradient to the similar Devils River, Waco, and Benton uplifts, interpreted as Precambrian basement-cored massifs. Above the Paleozoic sequence, a possible rift-related graben is imaged near the updip limit of Jurassic salt. Paleoshelf edges of the major Tertiary depositional sequences are marked by expanded sections disrupted by growth faults and shale diapirs. Within the Wilcox Formation, the transect crosses the mouth of the 900-m-deep Yoakum Canyon, a principal pathway of sediment delivery from the Laramide belt to the Gulf. Beneath the Wilcox, the Comanchean (Lower Cretaceous) shelf edge, capped by the Stuart City reef, is imaged as a pronounced topographic break onlapped by several moundy sediment packages. Because this segment of the line parallels strike, the topographic break may be interpreted as a 2,000-m-deep embayment in the Cretaceous shelf-edge, and possibly a major submarine canyon older and deeper than the Yoakum Canyon.« less

Tectonic evolution of the Tualatin basin, northwest Oregon, as revealed by inversion of gravity data

USGS Publications Warehouse

McPhee, Darcy K.; Langenheim, Victoria E.; Wells, Ray; Blakely, Richard J.

2014-01-01

The Tualatin basin, west of Portland (Oregon, USA), coincides with a 110 mGal gravity low along the Puget-Willamette lowland. New gravity measurements (n = 3000) reveal a three-dimensional (3-D) subsurface geometry suggesting early development as a fault-bounded pull-apart basin. A strong northwest-trending gravity gradient coincides with the Gales Creek fault, which forms the southwestern boundary of the Tualatin basin. Faults along the northeastern margin in the Portland Hills and the northeast-trending Sherwood fault along the southeastern basin margin are also associated with gravity gradients, but of smaller magnitude. The gravity low reflects the large density contrast between basin fill and the mafic crust of the Siletz terrane composing basement. Inversions of gravity data indicate that the Tualatin basin is ∼6 km deep, therefore 6 times deeper than the 1 km maximum depth of the Miocene Columba River Basalt Group (CRBG) in the basin, implying that the basin contains several kilometers of low-density pre-CRBG sediments and so formed primarily before the 15 Ma emplacement of the CRBG. The shape of the basin and the location of parallel, linear basin-bounding faults along the southwest and northeast margins suggest that the Tualatin basin originated as a pull-apart rhombochasm. Pre-CRBG extension in the Tualatin basin is consistent with an episode of late Eocene extension documented elsewhere in the Coast Ranges. The present fold and thrust geometry of the Tualatin basin, the result of Neogene compression, is superimposed on the ancestral pull-apart basin. The present 3-D basin geometry may imply stronger ground shaking along basin edges, particularly along the concealed northeast edge of the Tualatin basin beneath the greater Portland area.

Seismic structure of the southern Cascadia subduction zone and accretionary prism north of the Mendocino triple junction

USGS Publications Warehouse

Gulick, S.P.S.; Meltzer, A.M.; Clarke, S.H.

1998-01-01

Four multichannel-seismic reflection profiles, collected as part of the Mendocino triple junction seismic experiment, image the toe of the southern Cascadia accretionary prism. Today, 250-600 m of sediment is subducting with the Gorda plate, and 1500-3200 m is accreting to the northern California margin. Faults imaged west and east of the deformation front show mixed structural vergence. A north-south trending, 20 km long portion of the central margin is landward vergent for the outer 6-8 km of the toe of the prism. This region of landward vergence exhibits no frontal thrust, is unusually steep and narrow, and is likely caused by a seaward-dipping backstop close to the deformation front. The lack of margin-wide preferred seaward vergence and wedge-taper analysis suggests the prism has low basal shear stress. The three southern lines image wedge-shaped fragments of oceanic crust 1.1-7.3 km in width and 250-700 m thick near the deformation front. These wedges suggest shortening and thickening of the upper oceanic crust. Discontinuities in the seafloor west of the prism provide evidence for mass wasting in the form of slump blocks and debris fans. The southernmost profile extends 75 km west of the prism imaging numerous faults that offset both the Gorda basin oceanic crust and overlying sediments. These high-angle faults, bounding basement highs, are interpreted as strike-slip faults reactivating structures originally formed at the spreading ridge. Northeast or northwest trending strike-slip faults within the basin are consistent with published focal mechanism solutions and are likely caused by north-south Gorda-Pacific plate convergence. Copyright 1998 by the American Geophysical Union.

Controller certification: The generalized stability margin inference for a large number of MIMO controllers

NASA Astrophysics Data System (ADS)

Park, Jisang

In this dissertation, we investigate MIMO stability margin inference of a large number of controllers using pre-established stability margins of a small number of nu-gap-wise adjacent controllers. The generalized stability margin and the nu-gap metric are inherently able to handle MIMO system analysis without the necessity of repeating multiple channel-by-channel SISO analyses. This research consists of three parts: (i) development of a decision support tool for inference of the stability margin, (ii) computational considerations for yielding the maximal stability margin with the minimal nu-gap metric in a less conservative manner, and (iii) experiment design for estimating the generalized stability margin with an assured error bound. A modern problem from aerospace control involves the certification of a large set of potential controllers with either a single plant or a fleet of potential plant systems, with both plants and controllers being MIMO and, for the moment, linear. Experiments on a limited number of controller/plant pairs should establish the stability and a certain level of margin of the complete set. We consider this certification problem for a set of controllers and provide algorithms for selecting an efficient subset for testing. This is done for a finite set of candidate controllers and, at least for SISO plants, for an infinite set. In doing this, the nu-gap metric will be the main tool. We provide a theorem restricting a radius of a ball in the parameter space so that the controller can guarantee a prescribed level of stability and performance if parameters of the controllers are contained in the ball. Computational examples are given, including one of certification of an aircraft engine controller. The overarching aim is to introduce truly MIMO margin calculations and to understand their efficacy in certifying stability over a set of controllers and in replacing legacy single-loop gain and phase margin calculations. We consider methods for the computation of; maximal MIMO stability margins bP̂,C, minimal nu-gap metrics deltanu , and the maximal difference between these two values, through the use of scaling and weighting functions. We propose simultaneous scaling selections that attempt to maximize the generalized stability margin and minimize the nu-gap. The minimization of the nu-gap by scaling involves a non-convex optimization. We modify the XY-centering algorithm to handle this non-convexity. This is done for applications in controller certification. Estimating the generalized stability margin with an accurate error bound has significant impact on controller certification. We analyze an error bound of the generalized stability margin as the infinity norm of the MIMO empirical transfer function estimate (ETFE). Input signal design to reduce the error on the estimate is also studied. We suggest running the system for a certain amount of time prior to recording of each output data set. The assured upper bound of estimation error can be tuned by the amount of the pre-experiment.

Talc friction in the temperature range 25°–400 °C: relevance for fault-zone weakening

USGS Publications Warehouse

Moore, Diane E.; Lockner, David A.

2008-01-01

Talc has a temperature–pressure range of stability that extends from surficial to eclogite-facies conditions, making it of potential significance in a variety of faulting environments. Talc has been identified in exhumed subduction zone thrusts, in fault gouge collected from oceanic transform and detachment faults associated with rift systems, and recently in serpentinite from the central creeping section of the San Andreas fault. Typically, talc crystallized in the active fault zones as a result of the reaction of ultramafic rocks with silica-saturated hydrothermal fluids. This mode of formation of talc is a prime example of a fault-zone weakening process. Because of its velocity-strengthening behavior, talc may play a role in stabilizing slip at depth in subduction zones and in the creeping faults of central and northern California that are associated with ophiolitic rocks.

Local response of a glacier to annual filling and drainage of an ice-marginal lake

USGS Publications Warehouse

Walder, J.S.; Trabant, D.C.; Cunico, M.; Fountain, A.G.; Anderson, S.P.; Anderson, R. Scott; Malm, A.

2006-01-01

Ice-marginal Hidden Creek Lake, Alaska, USA, outbursts annually over the course of 2-3 days. As the lake fills, survey targets on the surface of the 'ice dam' (the glacier adjacent to the lake) move obliquely to the ice margin and rise substantially. As the lake drains, ice motion speeds up, becomes nearly perpendicular to the face of the ice dam, and the ice surface drops. Vertical movement of the ice dam probably reflects growth and decay of a wedge of water beneath the ice dam, in line with established ideas about jo??kulhlaup mechanics. However, the distribution of vertical ice movement, with a narrow (50-100 m wide) zone where the uplift rate decreases by 90%, cannot be explained by invoking flexure of the ice dam in a fashion analogous to tidal flexure of a floating glacier tongue or ice shelf. Rather, the zone of large uplift-rate gradient is a fault zone: ice-dam deformation is dominated by movement along high-angle faults that cut the ice dam through its entire thickness, with the sense of fault slip reversing as the lake drains. Survey targets spanning the zone of steep uplift gradient move relative to one another in a nearly reversible fashion as the lake fills and drains. The horizontal strain rate also undergoes a reversal across this zone, being compressional as the lake fills, but extensional as the lake drains. Frictional resistance to fault-block motion probably accounts for the fact that lake level falls measurably before the onset of accelerated horizontal motion and vertical downdrop. As the overall fault pattern is the same from year to year, even though ice is lost by calving, the faults must be regularly regenerated, probably by linkage of surface and bottom crevasses as ice is advected toward the lake basin.

Testing 8000 years of submarine paleoseismicity record offshore western Algeria : First evidence for irregular seismic cycles

NASA Astrophysics Data System (ADS)

Ratzov, G.; Cattaneo, A.; Babonneau, N.; Yelles, K.; Bracene, R.; Deverchere, J.

2012-12-01

It is commonly assumed that stress buildup along a given fault is proportional to the time elapsed since the previous earthquake. Although the resulting « seismic gap » hypothesis suits well for moderate magnitude earthquakes (Mw 4-5), large events (Mw>6) are hardly predictable and depict great variation in recurrence intervals. Models based on stress transfer and interactions between faults argue that an earthquake may promote or delay the occurrence of next earthquakes on adjacent faults by increasing or lowering the level of static stress. The Algerian margin is a Cenozoic passive margin presently inverted within the slow convergence between Africa and Eurasia plates (~3-6 mm/yr). The western margin experienced two large earthquakes in 1954 (Orléansville, M 6.7) and 1980 (El Asnam, M 7.3), supporting an interaction between the two faults. To get meaningful statistics of large earthquakes recurrence intervals over numerous seismic cycles, we conducted a submarine paleoseismicity investigation based on turbidite chronostratigraphy. As evidenced on the Cascadia subduction zone, synchronous turbidites accumulated over a large area and originated from independent sources are likely triggered by an earthquake. To test the method on a slowly convergent margin, we analyze turbidites from three sediment cores collected during the Maradja (2003) and Prisme (2007) cruises off the 1954-1980 source areas. We use X-ray radioscopy, XRF major elements counter, magnetic susceptibility, and grain-size distribution to accurately discriminate turbidites from hemipelagites. We date turbidites by calculating hemipelagic sedimentation rates obtained with radiocarbon ages, and interpolate the rates between turbidites. Finally, the age of events is compared with the only paleoseismic study available on land (El Asnam fault). Fourteen possible seismic events are identified by the counting and correlation of turbidites over the last 8 ka. Most events are correlated with the paleoseismic record of the El Asnam fault, but uncorrelated events suggest that other faults were active. Only the 1954 event (not the 1980) triggered a turbidity current, implying that the sediment buffer on the continental shelf could not be reloaded in 26 years, thus arguing for a minimum time resolution of our method. The new paleoseismic catalog shows a recurrence interval of 300-700 years for most events, but also a great interval of >1200 years without any major earthquake. This result suggests that the level of static stress may have drastically dropped as a result of three main events occurring within the 800 years prior the quiescence period.

A multiloop generalization of the circle criterion for stability margin analysis

NASA Technical Reports Server (NTRS)

Safonov, M. G.; Athans, M.

1979-01-01

In order to provide a theoretical tool suited for characterizing the stability margins of multiloop feedback systems, multiloop input-output stability results generalizing the circle stability criterion are considered. Generalized conic sectors with 'centers' and 'radii' determined by linear dynamical operators are employed to specify the stability margins as a frequency dependent convex set of modeling errors (including nonlinearities, gain variations and phase variations) which the system must be able to tolerate in each feedback loop without instability. The resulting stability criterion gives sufficient conditions for closed loop stability in the presence of frequency dependent modeling errors, even when the modeling errors occur simultaneously in all loops. The stability conditions yield an easily interpreted scalar measure of the amount by which a multiloop system exceeds, or falls short of, its stability margin specifications.

The continent-ocean transition on the northwestern South China Sea

NASA Astrophysics Data System (ADS)

Cameselle, Alejandra L.; Ranero, César R.; Franke, Dieter; Barckhausen, Udo

2015-04-01

Rifted margins are created as a result of stretching and breakup of continental lithosphere that eventually leads to oceanic spreading and formation of a new oceanic basin. A cornerstone for understanding how rift characteristics vary along strike in the same system and what processes control the final transition to seafloor spreading is the continent-ocean transition (COT). We use four regional multichannel seismic profiles and published magnetic lineations to study the structure and variability of COT on the northwest subbasin (NWSB) of the South China Sea and to discern continental from oceanic domains. The continental domain is characterized by tilted fault blocks overlaid by thick syn-rift sedimentary units and fairly continuous Moho reflections typically at 8-10 s twtt. Thickness of the continental crust changes from ~20-25 km under the uppermost slope to ~9-6 km under the lower slope. The oceanic domain is interpreted where a highly reflective top of basement, little faulting, no syntectonic strata, and fairly constant thickness basement (4-8 km) occur. The COT is imaged as a ~5-10 km wide zone where oceanic-type features abut continental-type structures. The South China margin is deformed by abundant normal faults dissecting the continental crust, whereas the conjugate Macclesfield Bank margin displays comparatively abrupt thinning and little faulting. Seismic profiles show an along-strike variation in the tectonic structure of the continental margin. The NE-most lines display ~20-40 km wide segments of intense faulting under the slope and associated continental-crust thinning. Towards the SW, faulting and thinning of the continental crust occurs across a ~100-110 km wide segment. We interpret this 3D structural variability and the narrow COT as a consequence of the abrupt termination of continental rifting tectonics by the NE to SW propagation of a spreading center. We suggest that breakup occurred by spreading center propagation to a larger degree than by lithospheric thinning during continental rifting. Based on the sedimentary successions overlying the oceanic crust, we propose a kinematic evolution for the oceanic domain of the NWSB consisting of a southward spreading center propagation followed by a first narrow ridge jump to the north, and then a younger larger jump to the SW into the east subbasin.

Investigating the 3-D Subduction Initiation Processes at Transform Faults and Passive Margins

NASA Astrophysics Data System (ADS)

Peng, H.; Leng, W.

2017-12-01

Studying the processes of subduction initiation is a key for understanding the Wilson cycle and improving the theory of plate tectonics. Previous studies investigated subduction initiation with geological synthesis and geodynamic modeling methods, discovering that subduction intends to initiate at the transform faults close to oceanic arcs, and that its evolutionary processes and surface volcanic expressions are controlled by plate strength. However, these studies are mainly conducted with 2-D models, which cannot deal with lateral heterogeneities of crustal thickness and strength along the plate interfaces. Here we extend the 2-D model to a 3-D parallel subduction model with high computational efficiency. With the new model, we study the dynamic controlling factors, morphology evolutionary processes and surface expressions for subduction initiation with lateral heterogeneities of material properties along transform faults and passive margins. We find that lateral lithospheric heterogeneities control the starting point of the subduction initiation along the newly formed trenches and the propagation speed for the trench formation. New subduction tends to firstly initiate at the property changing point along the transform faults or passive margins. Such finds may be applied to explain the formation process of the Izu-Bonin-Mariana (IBM) subduction zone in the western Pacific and the Scotia subduction zone at the south end of the South America. Our results enhance our understanding for the formation of new trenches and help to provide geodynamic modeling explanations for the observed remnant slabs in the upper mantle and the surface volcanic expressions.

Seismicity of the Earth 1900–2010 Himalaya and vicinity

USGS Publications Warehouse

Turner, Bethan; Jenkins, Jennifer; Turner, Rebecca; Parker, Amy; Sinclair, Alison; Davies, Sian; Hayes, Gavin P.; Villaseñor, Antonio; Dart, Rirchard L.; Tarr, Arthur C.; Furlong, Kevin P.; Benz, Harley M.

2013-01-01

Seismicity in the Himalaya region predominantly results from the collision of the India and Eurasia continental plates, which are converging at a relative rate of 40–50 mm/yr. Northward underthrusting of India beneath Eurasia generates numerous earthquakes and consequently makes this area one of the most seismically hazardous regions on Earth. The surface expression of the plate boundary is marked by the foothills of the north-south trending Sulaiman Range in the west, the Indo-Burmese Arc in the east, and the east-west trending Himalaya Front in the north of India. Along the western margin of the India plate, relative motions between India and Eurasia are accommodated by strike-slip, reverse, and oblique-slip faulting resulting in the complex Sulaiman Range fold and thrust belt, and the major translational Chaman Fault in Afghanistan. Beneath the Pamir‒Hindu Kush Mountains of northern Afghanistan, earthquakes occur to depths as great as 200 km as a result of remnant lithospheric subduction. Further north again, the Tian Shan is a seismically active intra-continental mountain belt defined by a series of east-west trending thrust faults thought to be related to the broad footprint of the India-Eurasia collision. Tectonics in northern India are dominated by motion along the Main Frontal Thrust and associated thrust faults of the India-Eurasia plate boundary, which have resulted in a series of large and devastating earthquakes in (and prior to) the 20th century. The Tibetan Plateau to the north of the main plate boundary is a broad region of uplift associated with the India-Eurasia collision, and is cut by a series of generally east-west trending strike-slip faults. These include the Kunlun, Haiyuan, and the Altyn Tagh faults, all of which are left-lateral structures, and the Kara-Koram right-lateral fault. Throughout the plateau, thrust faults accommodate the north-south compressional component of crustal shortening associated with the ongoing collision of India and Eurasia, while strike-slip and normal faults accommodate east-west extension. To the east, The Longmen Shan thrust belt marks the eastern margin of the Tibetan Plateau separating the complex tectonics of the plateau region from the relatively undeformed Sichuan Basin. Further south, the left-lateral Xiangshuihe-Xiaojiiang, right-lateral Red River and right-lateral Sagaing strike-slip fault systems accommodate deformation along the eastern margin of the India plate. Deep earthquakes have also occurred in the Indo-Burmese Arc region, thought to be an expression of eastward-directed subduction of the India plate, though whether subduction is ongoing is still debated.

On the initiation of subduction

NASA Technical Reports Server (NTRS)

Mueller, Steve; Phillips, Roger J.

1991-01-01

Estimates of shear resistance associated with lithospheric thrusting and convergence represent lower bounds on the force necessary to promote trench formation. Three environments proposed as preferential sites of incipient subduction are investigated: passive continental margins, transform faults/fracture zones, and extinct ridges. None of these are predicted to convert into subduction zones simply by the accumulation of local gravitational stresses. Subduction cannot initiate through the foundering of dense oceanic lithosphere immediately adjacent to passive continental margins. The attempted subduction of buoyant material at a mature trench can result in large compressional forces in both subducting and overriding plates. This is the only tectonic force sufficient to trigger the nucleation of a new subduction zone. The ubiquitous distribution of transform faults and fracture zones, combined with the common proximity of these features to mature subduction complexes, suggests that they may represent the most likely sites of trench formation if they are even marginally weaker than normal oceanic lithosphere.

Absolute Stability Analysis of a Phase Plane Controlled Spacecraft

NASA Technical Reports Server (NTRS)

Jang, Jiann-Woei; Plummer, Michael; Bedrossian, Nazareth; Hall, Charles; Jackson, Mark; Spanos, Pol

2010-01-01

Many aerospace attitude control systems utilize phase plane control schemes that include nonlinear elements such as dead zone and ideal relay. To evaluate phase plane control robustness, stability margin prediction methods must be developed. Absolute stability is extended to predict stability margins and to define an abort condition. A constrained optimization approach is also used to design flex filters for roll control. The design goal is to optimize vehicle tracking performance while maintaining adequate stability margins. Absolute stability is shown to provide satisfactory stability constraints for the optimization.

Stability of faults with heterogeneous friction properties and effective normal stress

NASA Astrophysics Data System (ADS)

Luo, Yingdi; Ampuero, Jean-Paul

2018-05-01

Abundant geological, seismological and experimental evidence of the heterogeneous structure of natural faults motivates the theoretical and computational study of the mechanical behavior of heterogeneous frictional fault interfaces. Fault zones are composed of a mixture of materials with contrasting strength, which may affect the spatial variability of seismic coupling, the location of high-frequency radiation and the diversity of slip behavior observed in natural faults. To develop a quantitative understanding of the effect of strength heterogeneity on the mechanical behavior of faults, here we investigate a fault model with spatially variable frictional properties and pore pressure. Conceptually, this model may correspond to two rough surfaces in contact along discrete asperities, the space in between being filled by compressed gouge. The asperities have different permeability than the gouge matrix and may be hydraulically sealed, resulting in different pore pressure. We consider faults governed by rate-and-state friction, with mixtures of velocity-weakening and velocity-strengthening materials and contrasts of effective normal stress. We systematically study the diversity of slip behaviors generated by this model through multi-cycle simulations and linear stability analysis. The fault can be either stable without spontaneous slip transients, or unstable with spontaneous rupture. When the fault is unstable, slip can rupture either part or the entire fault. In some cases the fault alternates between these behaviors throughout multiple cycles. We determine how the fault behavior is controlled by the proportion of velocity-weakening and velocity-strengthening materials, their relative strength and other frictional properties. We also develop, through heuristic approximations, closed-form equations to predict the stability of slip on heterogeneous faults. Our study shows that a fault model with heterogeneous materials and pore pressure contrasts is a viable framework to reproduce the full spectrum of fault behaviors observed in natural faults: from fast earthquakes, to slow transients, to stable sliding. In particular, this model constitutes a building block for models of episodic tremor and slow slip events.

Sedimentary and tectonic evolution of Plio Pleistocene alluvial and lacustrine deposits of Fucino Basin (central Italy)

NASA Astrophysics Data System (ADS)

Cavinato, Gian Paolo; Carusi, Claudio; Dall'Asta, Massimo; Miccadei, Enrico; Piacentini, Tommaso

2002-04-01

The Fucino Basin was the greatest lake of the central Italy, which was completely drained at the end of 19th century. The basin is an intramontane half-graben filled by Plio-Quaternary alluvial and lacustrine deposits located in the central part of the Apennines chain, which was formed in Upper Pliocene and in Quaternary time by the extensional tectonic activity. The analysis of the geological surface data allows the definition of several stratigraphic units grouped in Lower Units and Upper Units. The Lower Units (Upper Pliocene) are exposed along the northern and north-eastern basin margins. They consist of open to marginal lacustrine deposits, breccia deposits and fluvial deposits. The Upper Units (Lower Pliocene-Holocene) consist of interbedded marginal lacustrine deposits and fluvial deposits; thick coarse-grained fan-delta deposits are interfingered at the foot of the main relief with fluvial-lacustrine deposits. Most of the thickness of the lacustrine sequences (more than 1000-m thick) is buried below the central part of the Fucino Plain. The basin is bounded by E-W, WSW-ENE and NW-SE fault systems: Velino-Magnola Fault (E-W) and Tremonti-Celano-Aielli Fault (WSW-ENE) and S. Potito-Celano Fault (NW-SE) in the north; the Trasacco Fault, the Pescina-Celano Fault and the Serrone Fault (NW-SE) in the south-east. The geometry and kinematic indicators of these faults indicate normal or oblique movements. The study of industrial seismic profiles across the Fucino Basin gives a clear picture of the subsurface basin geometry; the basin shows triangular-shaped basin-fill geometry, with the maximum deposits thickness toward the main east boundary fault zones that dip south-westward (Serrone Fault, Trasacco Fault, Pescina-Celano Fault). On the basis of geological surface data, borehole stratigraphy and seismic data analysis, it is possible to recognize and to correlate sedimentary and seismic facies. The bottom of the basin is well recognized in the seismic lines available from the good and continuous signals of the top of Meso-Cenozoic carbonate rocks. The shape of sedimentary bodies indicates that the filling of the basin was mainly controlled by normal slip along the NW-SE boundary faults. In fact, the continental deposits are frequently in on-lap contact over the carbonate substratum; several disconformable contacts occurred during the sedimentary evolution of the basin. The main faults (with antithetic and synthetic fault planes) displace the whole sedimentary sequence up to the surface indicating a recent faults' activity (1915 Avezzano earthquake, Ms=7.0). The stratigraphic and tectonic setting of the Fucino Basin and neighboring areas indicates that the extensional tectonic events have had an important role in driving the structural-sedimentary evolution of the Plio-Quaternary deposits. The geometry of the depositional bodies, of the fault planes and their relationships indicate that the Fucino Basin was formed as a half-graben type structure during Plio-Quaternary extensional events. Some internal complexities are probably related to the fold-and-thrust structures of the Apenninic orogeny formed in Messinian time, in this area, and to a different activity timing of the E-W and WSW-ENE fault systems and the NW-SE fault systems. We believe, based on the similarity of the surface characteristics, that the structural setting of the Fucino Basin can be extrapolated to the other great intramontane basins in Central Italy (e.g. Rieti, L'Aquila, Sulmona, Sora, Isernia basins).

Variability in seismic properties of the décollement offshore Central Sumatra

NASA Astrophysics Data System (ADS)

Henstock, T.; Gardner, K.

2016-12-01

The plate boundary fault properties along subduction margins are primary controls on the magnitude, location and timing of megathrust earthquakes. We have reprocessed and analysed multichannel seismic reflection data from the Sumatra margin between Simeulue and Siberut; we have been careful to preserve amplitudes in order to allow us to investigate the properties of faults within the accretionary prism and the main plate boundary fault. Faults near the deformation front and beneath the initial folds clearly extend to oceanic basement, and the same is largely true where they can be clearly identified within the main part of the prism; limited exceptions appear to be present around topographic features on the downgoing plate. The biggest uncertainty in true amplitude studies is how to compensate for attenuation of the seismic waves. We use the variation in amplitude as a function of the prism thickness to estimate the effect of attenuation. Once the effects of attenuation are removed, absolute estimated reflection coefficients for the composite basement/decollement reflection are typically 0.1-0.15, although a small number of profiles show reflection coefficients as high as 0.2. The most likely cause of these variations is fluid content and pressure; we show examples where high amplitude prism faults link to a low amplitude decollement, suggesting hydraulic connectivity.

Worst-Case Flutter Margins from F/A-18 Aircraft Aeroelastic Data

NASA Technical Reports Server (NTRS)

Lind, Rick; Brenner, Marty

1997-01-01

An approach for computing worst-case flutter margins has been formulated in a robust stability framework. Uncertainty operators are included with a linear model to describe modeling errors and flight variations. The structured singular value, micron, computes a stability margin which directly accounts for these uncertainties. This approach introduces a new method of computing flutter margins and an associated new parameter for describing these margins. The micron margins are robust margins which indicate worst-case stability estimates with respect to the defined uncertainty. Worst-case flutter margins are computed for the F/A-18 SRA using uncertainty sets generated by flight data analysis. The robust margins demonstrate flight conditions for flutter may lie closer to the flight envelope than previously estimated by p-k analysis.

What controls the reactivation or preservation of distal ocean-continent transitions: the example of the Err-Platta nappes, SE Switzerland

NASA Astrophysics Data System (ADS)

Epin, Marie-Eva; Manatschal, Gianreto; Amann, Méderic

2016-04-01

Studies in the Alps suggest that remnants of former Ocean-Continent Transitions (OCT) can be preserved, even in internal parts of mountain belts. In the past, these units have been erroneously interpreted as either mélanges related to subduction channels or polyphase penetrative Alpine deformation. Good examples have been described from the eclogitic Piemonte units in the Western Alps and in Corsica [Beltrando et al., 2014], leading to the question of what may have controlled the preservation of these structures. In our study we used the example of the Err-Platta nappes that expose remnants of the OCT of the former Alpine Tethys. The aim of our presentation is to: 1) define the characteristic features of an OCT across a fossil magma-poor rifted margin, and 2) show the control of the rift-inherited structures during the subsequent reactivation of the OCT. The characteristics of OCTs at magma-poor rifted margins are the juxtaposition of serpentinized mantle and crustal rocks and pre-rift sediments limited by brittle extensional detachment faults sealed by syn- and post-tectonic sediments locally associated with magmatic rocks. Thus, in contrast to proximal margins, where lithologies are continuous layer cakes, OCTs are characterized by non-continuous layers and isolated blocks. To identify extensional detachment faults in mountain belts, different fingerprints can be found such as fault rocks (gouges and cataclasites) that bear a mantle derived fluid signature, or the occurrence of massive breccias that contain clasts of the underlying exhumed basement. Using field examples, we will show how Alpine structures selectively reactivated some inherited structures of the OCT, while others remained undeformed and were preserved in the nappe stack. How far the complex morphology, fault architecture and rheology of OCTs control the reactivation is still unclear, however, it appears that serpentinization fronts, or former extensional detachment faults may have played a key role during the reactivation of the margin. This study allows us to reconsider "mélange zone" described in many collisional orogens, and to test, using diagnostic criteria and field observations, if they could represent former OCTs. Beltrando et al. Earth Science Reviews (2014)

Active faults and deformation of the Catania margin (Eastern Sicily): preliminary results from the CRACK marine geophysical survey (Aug./Sep. 2016 R/V Tethys2)

NASA Astrophysics Data System (ADS)

Gutscher, M. A.; Dellong, D.; Graindorge, D.; Le Roy, P., Sr.; Dominguez, S.; Barreca, G.; Cunarro, D.; Petersen, F.; Urlaub, M.; Krastel, S.; Gross, F.; Kopp, H.

2016-12-01

The marine geophysical survey entitled CRACK (Catania margin, Relief, ACtive faults and historical earthquaKes) aims to investigate active faults offshore eastern Sicily. Several faults have been mapped onshore on the SE flank of Mt. Etna and recently a major strike-slip fault system was mapped in the deeper offshore area. The purpose of this study is to perform shallow water bathymetric mapping and a high-resolution sparker seismic survey in the shelf zone between the deep offshore and the onshore areas, a zone less well studied. Aside from the two fault systems mentioned above, there is also the Malta escarpment, the onshore (but buried) blind-thrust of the Gela Nappe and the lateral ramp thrust of the Calabrian accretionary wedge. Somehow all these structures connect offshore Catania, though exactly how is still unknown. The study will take place between 18 Aug. and 4 Sept. 2016 using the 25m long coastal research vessel Tethys2 and will consist of three 5-day legs. The first leg (zone 2) will be purely sparker seismics and legs 2 and 3 will be combined seismics and bathymetry along the shallow submarine SE flank of Mt. Etna (zone 1) and shallow continental shelf SE of Catania (zone 3). Some time during the first leg will also be devoted to submarine geodesy. Five submarine geodetic stations were deployed along the dextral strike-slip "North Alfeo - Etna" fault by the German GEOMAR Helmholtz Centre for Ocean Research Kiel in April 2016 (R/V Poseidon). The long-term monitoring campaign should help indicate in the future if this fault is slowly creeping or not currently moving. The first five months of data will be downloaded during the CRACK cruise.

Late Cenozoic transpressional mountain building directly north of the Altyn Tagh Fault in the Sanweishan and Nanjieshan, North Tibetan Foreland, China

NASA Astrophysics Data System (ADS)

Cunningham, Dickson; Zhang, Jin; Li, Yanfeng

2016-09-01

For many tectonicists, the structural development of the northern Tibetan Plateau stops at the Altyn Tagh Fault (ATF). This study challenges that assumption. Structural field observations and remote sensing analysis indicate that the Sanweishan and Nanjieshan basement cored ridges of the Archean Dunhuang Block, which interrupt the north Tibetan foreland directly north of the ATF, are bound and cut by an array of strike-slip, thrust and oblique-slip faults that have been active in the Quaternary and remain potentially active. The Sanweishan is a SE-tilted block that is bound on its NW margin by a steep south-dipping thrust fault that has also accommodated sinistral strike-slip displacements. The Nanjieshan consists of parallel, but offset basement ridges that record NNW and SSE thrust displacements and sinistral strike-slip. Regional folds characterize the extreme eastern Nanjieshan and appear to have formed above blind thrust faults which break the surface further west. Previously published magnetotelluric data suggest that the major faults of the Sanweishan and Nanjieshan ultimately root to the south within conductive zones that are inferred to merge into the ATF. Therefore, although the southern margin of the Dunhuang Block focuses significant deformation along the ATF, the adjacent cratonic basement to the north is also affected. Collectively, the ATF and structurally linked Sanweishan and Nanjieshan fault array represent a regional asymmetric half-flower structure that is dominated by non-strain partitioned sinistral transpression. The NW-trending Dengdengshan thrust fault system near Yumen City appears to define the northeastern limit of the Sanweishan-Nanjieshan block, which may be regionally viewed as the most northern, but early-stage expression of Tibetan Plateau growth into a slowly deforming, mechanically stiff Archean craton.

Corrugations on the S Reflector West of Spain: Kinematic Implications

NASA Astrophysics Data System (ADS)

Lymer, G.; Cresswell, D.; Reston, T. J.; Stevenson, C.; Bull, J.; Sawyer, D. S.

2016-12-01

The west Galicia margin (western Spain) provides favourable conditions to study the processes of continental extension and break-up through seismic imaging. Beneath the tilted fault blocks of the margin is a bright reflection, the S reflector, which is interpreted to be a detachment and the crust-mantle boundary. However questions remain concerning the role of the S during extension and in the mechanisms of breakup. To better understand the role of the S in continental breakup, a 3D multi-channel seismic dataset was acquired over the Galicia margin in summer 2013. It has been processed through to prestack time migration in collaboration with Repsol followed by depth conversion using velocities extracted from new velocity models based on wide-angle data across the Galicia margin and applied to a structural interpretation of the fault block structure. The faults that bound the present-day tilted blocks detach downward onto the S, suggesting that the S is a rooted detachment surface that formed late in the rifting history of the Galicia margin. The fact that the syn-tectonic sediments related to the block bounding faults represent only the latest part of the syn-rift units also supports a late development of the S detachment. The map of the S reveals a series of linear and parallel low ridges and troughs, also evident on the amplitude map of S, that are neither velocity distortions nor artefacts. We interpret these as slip surface "corrugations" and relate them to the slip direction during the rifting. The orientation of the corrugations changes oceanward, from E-W to ESE-WNW. It either suggests that slip on S was diachronous and that the extension direction changed as it migrated oceanward, or that the extension can be described as a clockwise rotation of the COT about a pole located 80km north of the 3D volume, just west of the northern Galicia Bank. There the edges of the Galicia Bank and the Galicia Escarpment appear in the bathymetry as a "V" shape opening to the south, which is reliable to a rotation of the area. Such a rotation is also consistent with the southward increasing internal deformation of some of the basement blocks along the margin. In either case it reveals the 3D complexity of the extension processes leading to breakup.

Seismicity of the Earth 1900-2013 offshore British Columbia-southeastern Alaska and vicinity

USGS Publications Warehouse

Hayes, Gavin P.; Smoczyk, Gregory M.; Ooms, Jonathan G.; McNamara, Daniel E.; Furlong, Kevin P.; Benz, Harley M.; Villaseñor, Antonio

2014-01-01

The tectonics of the Pacific margin of North America between Vancouver Island and south-central Alaska are dominated by the northwest motion of the Pacific plate with respect to the North America plate at a velocity of approximately 50 mm/yr. In the south of this mapped region, convergence between the northern extent of the Juan de Fuca plate (also known as the Explorer microplate) and North America plate dominate. North from the Explorer, Pacific, and North America plate triple junction, Pacific:North America motion is accommodated along the ~650-km-long Queen Charlotte fault system. Offshore of Haida Gwaii and to the southwest, the obliquity of the Pacific:North America plate motion vector creates a transpressional regime, and a complex mixture of strike-slip and convergent (underthrusting) tectonics. North of the Haida Gwaii islands, plate motion is roughly parallel to the plate boundary, resulting in almost pure dextral strike-slip motion along the Queen Charlotte fault. To the north, the Queen Charlotte fault splits into multiple structures, continuing offshore of southwestern Alaska as the Fairweather fault, and branching east into the Chatham Strait and Denali faults through the interior of Alaska. The plate boundary north and west of the Fairweather fault ultimately continues as the Alaska-Aleutians subduction zone, where Pacific plate lithosphere subducts beneath the North America plate at the Aleutians Trench. The transition is complex, and involves intraplate structures such as the Transition fault. The Pacific margin offshore British Columbia is one of the most active seismic zones in North America and has hosted a number of large earthquakes historically.

Evolution of Devonian carbonate-shelf margin, Nevada

USGS Publications Warehouse

Morrow, J.R.; Sandberg, C.A.

2008-01-01

The north-trending, 550-km-long Nevada segment of the Devonian carbonate-shelf margin, which fringed western North America, evidences the complex interaction of paleotectonics, eustasy, biotic changes, and bolide impact-related influences. Margin reconstruction is complicated by mid-Paleozoic to Paleogene compressional tectonics and younger extensional and strike-slip faulting. Reports published during the past three decades identify 12 important events that influenced development of shelf-margin settings; in chronological order, these are: (1) Early Devonian inheritance of Silurian stable shelf inargin, (2) formation of Early to early Middle 'Devonian shelf-margin basins, (3) propradation of later Middle Devonian shelf margin, (4) late Middle Devonian Taghanic ondap and continuing long-term Frasnian transgression, (5) initiation of latest Middle Devonian to early Frasnian proto-Antler orogenic forebulge, (6) mid-Frasnian Alamo Impact, (7) accelerated development of proto-Antler forebulge and backbulge Pilot basin, (8) global late Frasnian sentichatovae sea-level rise, (9) end-Frasnian sea-level fluctuations and ensuing mass extinction, (10) long-term Famennian regression and continept-wide erosion, (11) late Famennian emergence: of Ahtler orogenic highlands, and (12) end-Devonian eustatic sea-level fall. Although of considerable value for understanding facies relationships and geometries, existing standard carbonate platform-margin models developed for passive settings else-where do not adequately describe the diverse depositional and, structural settings along the Nevada Devonian platform margin. Recent structural and geochemical studies suggest that the Early to Middle Devonian-shelf-margin basins may have been fault-bound and controlled by inherited Precambrian structure. Subsequently, the migrating latest Middle to Late Devonian Antler orogenic forebulge exerted a dominant control on shelf-margin position, morphology, and sedimentation. ??Geological Society of America.

An unrecognized major collision of the Okhotomorsk Block with East Asia during the Late Cretaceous, constraints on the plate reorganization of the Northwest Pacific

NASA Astrophysics Data System (ADS)

Yang, Yong-Tai

2013-11-01

Interactions at plate boundaries induce stresses that constitute critical controls on the structural evolution of intraplate regions. However, the traditional tectonic model for the East Asian margin during the Mesozoic, invoking successive episodes of paleo-Pacific oceanic subduction, does not provide an adequate context for important Late Cretaceous dynamics across East Asia, including: continental-scale orogenic processes, significant sinistral strike-slip faulting, and several others. The integration of numerous documented field relations requires a new tectonic model, as proposed here. The Okhotomorsk continental block, currently residing below the Okhotsk Sea in Northeast Asia, was located in the interior of the Izanagi Plate before the Late Cretaceous. It moved northwestward with the Izanagi Plate and collided with the South China Block at about 100 Ma. The indentation of the Okhotomorsk Block within East Asia resulted in the formation of a sinistral strike-slip fault system in South China, formation of a dextral strike-slip fault system in North China, and regional northwest-southeast shortening and orogenic uplift in East Asia. Northeast-striking mountain belts over 500 km wide extended from Southeast China to Southwest Japan and South Korea. The peak metamorphism at about 89 Ma of the Sanbagawa high-pressure metamorphic belt in Southwest Japan was probably related to the continental subduction of the Okhotomorsk Block beneath the East Asian margin. Subsequently, the north-northwestward change of motion direction of the Izanagi Plate led to the northward movement of the Okhotomorsk Block along the East Asian margin, forming a significant sinistral continental transform boundary similar to the San Andreas fault system in California. Sanbagawa metamorphic rocks in Southwest Japan were rapidly exhumed through the several-kilometer wide ductile shear zone at the lower crust and upper mantle level. Accretionary complexes successively accumulated along the East Asian margin during the Jurassic-Early Cretaceous were subdivided into narrow and subparallel belts by the upper crustal strike-slip fault system. The departure of the Okhotomorsk Block from the northeast-striking Asian margin resulted in the occurrence of an extensional setting and formation of a wide magmatic belt to the west of the margin. In the Campanian, the block collided with the Siberian margin, in Northeast Asia. At about 77 Ma, a new oceanic subduction occurred to the south of the Okhotomorsk Block, ending its long-distance northward motion. Based on the new tectonic model, the abundant Late Archean to Early Proterozoic detrital zircons in the Cretaceous sandstones in Kamchatka, Southwest Japan, and Taiwan are interpreted to have been sourced from the Okhotomorsk Block basement which possibly formed during the Late Archean and Early Proterozoic. The new model suggests a rapidly northward-moving Okhotomorsk Block at an average speed of 22.5 cm/yr during 89-77 Ma. It is hypothesized that the Okhotomorsk-East Asia collision during 100-89 Ma slowed down the northwestward motion of the Izanagi Plate, while slab pull forces produced from the subducting Izanagi Plate beneath the Siberian margin redirected the plate from northwestward to north-northwestward motion at about 90-89 Ma.

Sliding Mode Fault Tolerant Control with Adaptive Diagnosis for Aircraft Engines

NASA Astrophysics Data System (ADS)

Xiao, Lingfei; Du, Yanbin; Hu, Jixiang; Jiang, Bin

2018-03-01

In this paper, a novel sliding mode fault tolerant control method is presented for aircraft engine systems with uncertainties and disturbances on the basis of adaptive diagnostic observer. By taking both sensors faults and actuators faults into account, the general model of aircraft engine control systems which is subjected to uncertainties and disturbances, is considered. Then, the corresponding augmented dynamic model is established in order to facilitate the fault diagnosis and fault tolerant controller design. Next, a suitable detection observer is designed to detect the faults effectively. Through creating an adaptive diagnostic observer and based on sliding mode strategy, the sliding mode fault tolerant controller is constructed. Robust stabilization is discussed and the closed-loop system can be stabilized robustly. It is also proven that the adaptive diagnostic observer output errors and the estimations of faults converge to a set exponentially, and the converge rate greater than some value which can be adjusted by choosing designable parameters properly. The simulation on a twin-shaft aircraft engine verifies the applicability of the proposed fault tolerant control method.

Geometry and kinematics of accretionary wedge faults inherited from the structure and rheology of the incoming sedimentary section; insights from 3D seismic reflection data

NASA Astrophysics Data System (ADS)

Bell, Rebecca; Orme, Haydn; Lenette, Kathryn; Jackson, Christopher; Fitch, Peter; Phillips, Thomas; Moore, Gregory

2017-04-01

Intra-wedge thrust faults represent important conduits for fluid flow in accretionary prisms, modulating pore fluid pressure, effective stress and, ultimately, the seismic hazard potential of convergent plate boundaries. Despite its importance, we know surprisingly little regarding the 3D geometry and kinematics of thrust networks in accretionary prisms, largely due to a lack of 3D seismic reflection data providing high-resolution, 3D images. To address this we here present observations from two subduction zones, the Nankai and Lesser Antilles margins, where 3D seismic and borehole data allow us to constrain the geometry and kinematics of intra-wedge fault networks and to thus shed light on the mechanisms responsible for their structural style variability. At the Muroto transect, Nankai margin we find that the style of protothrust zone deformation varies markedly along-strike over distances of only a few km. Using structural restoration and quantitative fault analysis, we reveal that in the northern part of the study area deformation occurred by buckle folding followed by faulting. Further south, intra-wedge faults nucleate above the décollement and propagate radially with no folding, resulting in variable connectivity between faults and the décollement. The seismic facies character of sediments immediately above the décollement varies along strike, with borehole data revealing that, in the north, where buckle folding dominates un-cemented Lower Shikoku Basin sediments overlie the décollement. In contrast, further south, Opal CT-cemented, and thus rigid Upper Shikoku Basin sediments overlie the décollement. We suggest these along-strike variations in diagenesis and thus rheology control the observed structural style variability. Near Barbados, at the Lesser Antilles margin, rough subducting plate relief is blanketed by up to 700 m of sediment. 3D seismic data reveal that basement relief is defined by linear normal fault blocks and volcanic ridges, and sub-circular seamounts. The youngest, most basinward thrusts in the wedge strike NW-SE; however, 17 km landward, towards the wedge core, they strike NE-SW. The orientation of the more landward faults correlates with the trend of linear basement relief, whereas thrust fault orientations close to the deformation front are perpendicular to the convergence direction. We notice that oceanic crust that has been subducted is characterised by NE-SW striking, now-inverted normal faults, with some faults extending up through the entire sedimentary section. We suggest that the NE-SW orientation of thrust faults has been inherited from linear basement ridges. In contrast, basement currently subducting beneath the deformation front is dominated by seamounts and is devoid of more linear features. Here, there are no pre-existing normal faults available for reactivation and thrust faults develop perpendicular to the convergence direction. We show that the incoming plate properties have a profound effect on the geometry of accretionary wedges; it would be difficult to elucidate this without 3D seismic data. Our insights provide new hypotheses that can be tested with numerical and laboratory models.

Mesozoic architecture of a tract of the European-Iberian continental margin: Insights from preserved submarine palaeotopography in the Longobucco Basin (Calabria, Southern Italy)

NASA Astrophysics Data System (ADS)

Santantonio, Massimo; Fabbi, Simone; Aldega, Luca

2016-01-01

The sedimentary successions exposed in northeast Calabria document the Jurassic-Early Cretaceous tectonic-sedimentary evolution of a former segment of the European-Iberian continental margin. They are juxtaposed today to units representing the deformation of the African and Adriatic plates margins as a product of Apenninic crustal shortening. A complex pattern of unconformities reveals a multi-stage tectonic evolution during the Early Jurassic, which affected the facies and geometries of siliciclastic and carbonate successions deposited in syn- and post-rift environments ranging from fluvial to deep marine. Late Sinemurian/Early Pliensbachian normal faulting resulted in exposure of the Hercynian basement at the sea-floor, which was onlapped by marine basin-fill units. Shallow-water carbonate aprons and reefs developed in response to the production of new accommodation space, fringing the newborn islands which represent structural highs made of Paleozoic crystalline and metamorphic rock. Their drowning and fragmentation in the Toarcian led to the development of thin caps of Rosso Ammonitico facies. Coeval to these deposits, a thick (> 1 km) hemipelagic/siliciclastic succession was sedimented in neighboring hanging wall basins, which would ultimately merge with the structural high successions. Footwall blocks of the Early Jurassic rift, made of Paleozoic basement and basin-margin border faults with their onlapping basin-fill formations, are found today at the hanging wall of Miocene thrusts, overlying younger (Middle/Late Jurassic to Late Paleogene) folded basinal sediments. This paper makes use of selected case examples to describe the richly diverse set of features, ranging from paleontology to sedimentology, to structural geology, which are associated with the field identification of basin-margin unconformities. Our data provide key constraints for restoring the pre-orogenic architecture of a continental margin facing a branch of the Liguria-Piedmont ocean in the Western Tethys, and for estimating displacements and slip rates along synsedimentary faults.

Lithosperic rheology controls on oceanic spreading patterns

NASA Astrophysics Data System (ADS)

Gerya, T.

2012-04-01

Mid-ocean ridges sectioned by transform faults represent one of the most prominent surface expressions of terrestrial plate tectonics. A fundamental long standing problem of plate tectonics is how and why ridge-transform spreading patterns are formed and maintained. On the one hand, geometrical correspondence between mid-ocean ridges and respective rifted margins apparently suggests that many oceanic transform faults are inherited structures that persisted throughout the entire history of oceanic spreading. On the other hand, data from incipient oceanic spreading regions show that transform faults are not directly inherited from transverse rift structures and start to develop as or after oceanic spreading nucleate. Based on self-consistent 3D thermomechanical numerical model of oceanic spreading we demonstrate that only limited range of oceanic lithosphere rheologies can reproduce natural spreading patterns. In particular, spontaneous formation and long-term stability of orthogonal ridge-transform spreading pattern requires visco-brittle/plastic rheology of plates with strong dynamic weakening of spontaneously forming faults. Our, numerical models of incipient oceanic spreading demonstrate that one or several oceanic transform faults can form gradually within broad non-transform accommodation zones connecting initially offset spreading centers. Orientation of transform faults and spreading centers changes exponentially with time as the result of new oceanic crust growth. The resulting orthogonal ridge-transform system is established within few millions of years after the beginning of oceanic spreading. By its fundamental physical origin, this system is a crustal growth pattern governed by space accommodation and not a plate breakup pattern governed by stress distribution. It is demonstrated that the characteristic extension-parallel orientation of oceanic transform faults can be obtained from space accommodation criteria as a steady state orientation of a strike-slip fault sustaining in between simultaneously growing offset crustal segments. Numerical models also suggest that transform faults can develop at single straight ridge as the result of dynamical instability of constructive plate boundaries caused by weakening of forming brittle/plastic fractures. Boundary instability from asymmetric plate growth can spontaneously start in alternate directions along successive ridge sections; the resultant curved ridges become transform faults within a few million years. Offsets along the transform faults change continuously with time by asymmetric plate growth and discontinuously by ridge jumps. Degree of asymmetric plate accretion increases with increasing degree of brittle/plastic weakening. It is also strongly dependent on the brittle/plastic yielding criterion and is notably reduced in models with pressure-dependent brittle/plastic plate strength compared to models with pressure-independent strength.

Partitioning of deformation along a reactivated rifted margin: example of the northern Ligurian margin.

NASA Astrophysics Data System (ADS)

Sage, Françoise; Beslier, Marie-Odile; Gaullier, Virginie; Larroque, Christophe; Dessa, Jean-Xavier; Mercier de Lepinay, Bernard; Corradi, Nicola; Migeon, Sébastien; Katz, Hélène; Ruiz Constan, Ana

2013-04-01

The northern Ligurian margin, of Oligo-Miocene age, is currently undergoing compression related to microplate motions and/or to gravity spreading of the Alpine chain located immediately north of it. Active thrust faults and folds have previously been identified below the margin, together with a global uplift of the continental edge, since at least the Messinian. The seismicity that goes with the present-day margin contraction (e.g. Mw 6.9, 1887/02/23) extends to the axis of the adjacent oceanic basin (e.g. ML 6.0, 1963/07/19; ML 5.4, 2011/07/07). However, we do not know of any recent or active crustal contractional structure within this oceanic domain. In this study, we use new 12-channel high-resolution seismic data (FABLES seismic cruise, 2012, R/V Tethys II) in order to image the sedimentary cover of the Ligurian oceanic basin, up to ~3km below the seabed, including the Plio-Quaternary and the Messinian sediment down to the bottom of the Messinian salt layer. Because the Messinian event is well dated (5.96-5.32 Ma) and well identified in the seismic data, it forms a clear marker that we use to characterize the recent deformation related to both mobile salt motion and crustal tectonics. About 50 km south of the margin offshore of Italy, we identify huge and complex salt walls that elongate SW-NE. Such salt walls, which cannot be explained by salt tectonics only, are interpreted as evidence of deep-seated crustal deformation. They form en echelon structures that are well expressed in the seabed morphology, and do not correspond to any significant vertical throw at the base of the salt layer. This suggests that within the deep basin, mainly strike-slip faulting accommodates long-term crustal deformation. It thus offers a contrast with the margin where deformation is mainly marked by shortening and reverse faulting, with vertical throws of several hundred meters. This discrepancy in the tectonic styles between the margin and the adjacent oceanic basin suggests some partitioning of the deformation. It may result from the difference in the topographic gradient of the main crustal interfaces between the steep margin and the adjacent oceanic domain, and/or to different mechanical behaviours of the adjacent lithospheric domains.

IODP drilling in the South China Sea in 2017 will address the mechanism of continental breakup

NASA Astrophysics Data System (ADS)

Sun, Z.; Larsen, H. C.; Lin, J.; Pang, X.; McIntosh, K. D.; Stock, J. M.; Jian, Z.; Wang, P.; Li, C.

2016-12-01

Geophysical exploration and scientific drilling along the North Atlantic rifted continental margins suggested that passive continental margins can be classified into two end members: magma-rich and magma-poor. Bearing seaward-dipping reflector sequences (SDRS) and highly mafic underplated high velocity lower crust (HVLC), the magma-rich margin is thought to be related to large igneous provinces (LIP) or mantle plume activity. Magma-poor margins have been drilled offshore Iberia and Newfoundland, where brittle faults cut through the whole crust and reach the upper mantle. Following seawater infiltration, the mantle was serpentinized and exhumed in the continent-ocean transition zone (COT). Later geophysical exploration and modeling suggested that in magma-poor margins lithosphere may break up in different styles, including uniform breakup, lower crust exhumation, or upper mantle exhumed at the COT, etc. The northern continental margin of the South China Sea (SCS) between longitude 114.5º and 116.5º hosts features that might be similar to both of the two end-members defined in the North Atlantic. Wide-angle seismic studies suggest that below the inner margin, crustal underplating of high velocity material is present, while syn-rift as well as post-rift intrusive features are visible and have in places been verified by industry drilling. However, the profound volcanism and associated SDRS formation are entirely lacking, and thus classification as a volcanic rifted margin can be ruled out. Instead, the COT exhibits a profound thinning of the continental crust towards the ocean crust of the SCS, showing some similarity to the Iberia type margin. The crustal thinning is caused by low-angle faults that have stretched the upper continental crust. There are indications of lower crustal flow toward the SCS. Alternatively, these extensional faults may have reached the lithospheric mantle and generated serpentinized material in a similar fashion as seen off Iberia. It will require deep drilling and sampling of characteristic basement units within the COT to distinguish. Four months of drilling by IODP to address this question is scheduled for February to June in 2017. The IODP drilling has the potential to support a third breakup mechanism theorized by modelling in addition to the two types drilled.

Early Oscillation Detection for DC/DC Converter Fault Diagnosis

NASA Technical Reports Server (NTRS)

Wang, Bright L.

2011-01-01

The electrical power system of a spacecraft plays a very critical role for space mission success. Such a modern power system may contain numerous hybrid DC/DC converters both inside the power system electronics (PSE) units and onboard most of the flight electronics modules. One of the faulty conditions for DC/DC converter that poses serious threats to mission safety is the random occurrence of oscillation related to inherent instability characteristics of the DC/DC converters and design deficiency of the power systems. To ensure the highest reliability of the power system, oscillations in any form shall be promptly detected during part level testing, system integration tests, flight health monitoring, and on-board fault diagnosis. The popular gain/phase margin analysis method is capable of predicting stability levels of DC/DC converters, but it is limited only to verification of designs and to part-level testing on some of the models. This method has to inject noise signals into the control loop circuitry as required, thus, interrupts the DC/DC converter's normal operation and increases risks of degrading and damaging the flight unit. A novel technique to detect oscillations at early stage for flight hybrid DC/DC converters was developed.

Geometry and kinematics of the Triassic rift basin in Jameson Land (East Greenland)

NASA Astrophysics Data System (ADS)

Guarnieri, Pierpaolo; Brethes, Anaïs.; Rasmussen, Thorkild M.

2017-04-01

The Triassic rift basin along the east Greenland margin described in this paper is represented by NE-SW trending basins and highs segmented by NW-SE trending transfer zones. Coarse-grained sediments along the eastern side of Jameson Land are shown to be hosted in half-graben structures belonging to the Carlsberg Fjord Basin that is bounded by NW dipping normal faults mapped and described after fieldwork in the Klitdal area in Liverpool Land. New aeromagnetic and electromagnetic data together with new drill cores allow the reinterpretation of available seismic lines showing the continuation of the Triassic rift basin toward the SW where it is buried under the Upper Triassic postrift sediments and the Jurassic successions of the Jameson Land Basin. The N-S trending Liverpool Land, interpreted as the boundary block of the Triassic basin, is shown to represent a structural high inherited from the Late Carboniferous tectonics and faulted during the Triassic rifting. The Carlsberg Fjord Basin and the Klitdal Fault System described in this paper should be seen as analogues to the Helgeland Basin in the Norwegian offshore that is bounded by the Ylvingen Fault Zone and to the Papa and West of Shetlands Basins that are bounded by the Spine Fault. The Triassic rift zone and transfer faults on both conjugate margins show a straightforward correlation with the trends of the initial spreading line and fracture zones of the northeast Atlantic indicating a possible inheritance of the Triassic rifting.

Structural and numerical modeling of fluid flow and evolving stress fields at a transtensional stepover: A Miocene Andean porphyry copper system as a case study.

NASA Astrophysics Data System (ADS)

Nuñez, R. C.; Griffith, W. A.; Mitchell, T. M.; Marquardt, C.; Iturrieta, P. C.; Cembrano, J. M.

2017-12-01

Obliquely convergent subduction orogens show both margin-parallel and margin-oblique fault systems that are spatially and temporally associated with ore deposits and geothermal systems within the volcanic arc. Fault orientation and mechanical interaction among different fault systems influence the stress field in these arrangements, thus playing a first order control on the regional to local-scale fluid migration paths as documented by the spatial distribution of fault-vein arrays. Our selected case study is a Miocene porphyry copper-type system that crops out in the precordillera of the Maule region along the Teno river Valley (ca. 35°S). Several regional to local faults were recognized in the field: (1) Two first-order, N-striking subvertical dextral faults overlapping at a right stepover; (2) Second-order, N60°E-striking steeply-dipping, dextral-normal faults located at the stepover, and (3) N40°-60°W striking subvertical, sinistral faults crossing the stepover zone. The regional and local scale geology is characterized by volcano-sedimentary rocks (Upper Eocene- Lower Miocene), intruded by Miocene granodioritic plutons (U-Pb zircon age of 18.2 ± 0.11 Ma) and coeval dikes. We implement a 2D boundary element displacement discontinuity method (BEM) model to test the mechanical feasibility of kinematic model of the structural development of the porphyry copper-type system in the stepover between N-striking faults. The model yields the stress field within the stepover region and shows slip and potential opening distribution along the N-striking master faults under a regionally imposed stress field. The model shows that σ1 rotates clockwise where the main faults approach each other, becoming EW when they overlap. This, in turn leads to the generation of both NE- and NW-striking faults within the stepover area. Model results are consistent with the structural and kinematic data collected in the field attesting for enhanced permeability and fluid flow transport and arrest spatially associated with the stepover.

Estimation of the depth of faulting in the northeast margin of Argyre basin (Mars) by structural analysis of lobate scarps

NASA Astrophysics Data System (ADS)

Herrero-Gil, Andrea; Ruiz, Javier; Egea-González, Isabel; Romeo, Ignacio

2017-04-01

Lobate scarps are tectonic structures considered as the topographic expression of thrust faults. For this study we have chosen three large lobate scarps (Ogygis Rupes, Bosporos Rupes and a third unnamed one) located in Aonia Terra, in the southern hemisphere of Mars near the northeast margin of the Argyre impact basin. These lobate scarps strike parallel to the edge of Thaumasia in this area, showing a roughly arcuate to linear form and an asymmetric cross section with a steeply frontal scarp and a gently dipping back scarp. The asymmetry in the cross sections suggests that the three lobate scarps were generated by ESE-vergent thrust faults. Two complementary methods were used to analyze the faults underlying these lobate scarps based on Mars Orbiter Laser Altimeter data and the Mars imagery available: (i) analyzing topographic profiles together with the horizontal shortening estimations from cross-cut craters to create balanced cross sections on the basis of thrust fault propagation folding [1]; (ii) using a forward mechanical dislocation method [2], which predicts fault geometry by comparing model outputs with real topography. The objective is to obtain fault geometry parameters as the minimum value for the horizontal offset, dip angle and depth of faulting of each underlying fault. By comparing the results obtained by both methods we estimate a preliminary depth of faulting value between 15 and 26 kilometers for this zone between Thaumasia and Argyre basin. The significant sizes of the faults underlying these three lobate scarps suggest that their detachments are located at a main rheological change. Estimates of the depth of faulting in similar lobate scarps on Mars or Mercury [3] have been associated to the depth of the brittle-ductile transition. [1] Suppe (1983), Am. J. Sci., 283, 648-721; Seeber and Sorlien (2000), Geol. Soc. Am. Bull., 112, 1067-1079. [2] Toda et al. (1998) JGR, 103, 24543-24565. [3] i.e. Schultz and Watters (2001) Geophys. Res. Lett., 28, 4659-4662; Ruiz et al. (2008) EPSL, 270, 1-12; Egea-Gonzalez et al. (2012) PSS, 60, 193-198; Mueller et al. (2014) EPSL, 408, 100-109.

The Phuket Terrane: A Late Palaeozoic rift at the margin of Sibumasu

NASA Astrophysics Data System (ADS)

Ridd, Michael F.

2009-09-01

It is widely accepted that Sibumasu rifted from Gondwana in the Late Palaeozoic. But the rifts themselves have not previously been documented in Southeast Asia. This paper identifies the pre-Middle Permian Kaeng Krachan Group of Upper Peninsular Thailand as the infill of one such rift, which is given the name Phuket Terrane. Indirect evidence suggests the rift-infill is several kilometres thick and glacially-influenced diamictites are conspicuous in the succession. There are significant similarities with the >3 km thick pre-Middle Permian rift-infill of the Carnarvon Basin of Western Australia. East of the Khlong Marui Fault belt the succession is thinner and diamictites are a minor component. A tectono-stratigraphic model is proposed involving Gondwana glaciers dropping their load at the (present) western margin of the Phuket Terrane from where it was re-sedimented in the rapidly subsiding marine rift basin. It is suggested that the Khlong Marui Fault formed part of the eastern boundary of the rift system. The Three Pagodas Fault belt similarly juxtaposes different pre-Middle Permian successions. Rifting ceased in the Early Permian and a passive margin formed as the Mesotethys ocean widened, the upper part of the Kaeng Krachan Group and the overlying Ratburi Limestone representing the post-rift sequence.

E-W strike slip shearing of Kinwat granitoid at South East Deccan Volcanic Province, Kinwat, Maharashtra, India

NASA Astrophysics Data System (ADS)

Kaplay, R. D.; Kumar, T. Vijay; Mukherjee, Soumyajit; Wesanekar, P. R.; Babar, Md; Chavan, Sumeet

2017-07-01

We study the margin of South East Deccan Volcanic Province around Kinwat lineament, Maharashtra, India, which is NW extension of the Kaddam Fault. Structural field studies document ˜ E-W strike-slip mostly brittle faults from the basement granite. We designate this as `Western boundary East Dharwar Craton Strike-slip Zone' (WBEDCSZ). At local level, the deformation regime from Kinwat, Kaddam Fault, micro-seismically active Nanded and seismically active Killari corroborate with the nearby lineaments. Morphometric analyses suggest that the region is moderately tectonically active. The region of intense strike-slip deformation lies between seismically active fault along Tapi in NW and Bhadrachalam in the SE part of the Kaddam Fault/lineament. The WBEDCSZ with the surface evidences of faulting, presence of a major lineaments and intersection of faults could be a zone of intraplate earthquake.

Opposing effects of stacking faults and antisite domain boundaries on the conduction band edge in kesterite quaternary semiconductors

NASA Astrophysics Data System (ADS)

Park, Ji-Sang; Kim, Sunghyun; Walsh, Aron

2018-01-01

We investigated stability and the electronic structure of extended defects including antisite domain boundaries and stacking faults in the kesterite-structured semiconductors, Cu2ZnSnS4 (CZTS) and Cu2ZnSnSe4 (CZTSe). Our hybrid density functional theory calculations show that stacking faults in CZTS and CZTSe induce a higher conduction band edge than the bulk counterparts, and thus the stacking faults act as electron barriers. Antisite domain boundaries, however, accumulate electrons as the conduction band edge is reduced in energy, having an opposite role. An Ising model was constructed to account for the stability of stacking faults, which shows the nearest-neighbor interaction is stronger in the case of the selenide.

Gas Migration Processes through the Gas Hydrate Stability Zone at Four-Way Closure Ridge Offshore SW Taiwan

NASA Astrophysics Data System (ADS)

Kunath, P.; Chi, W. C.; Berndt, C.; Liu, C. S.

2016-12-01

We have used 3D P-Cable seismic data from Four-Way-Closure Ridge, a NW-SE trending anticlinal ridge within the lower slope domain of accretionary wedge, to investigate the geological constraints influencing the fluid migration pattern in the shallow marine sediments. In the seismic data, fluid migration feature manifests itself as high reflection layers of dipping strata, which originate underneath a bottom simulating reflector (BSR) and extend towards the seafloor. Shoaling of the BSR near fluid migration pathways indicates a focused fluid flux, perturbing the temperature field. Furthermore, seafloor video footage confirmed the presence of recent methane seepage above seismically imaged fluid migration pathways. We plan to test two hypotheses for the occurrence of these fluid migration pathways: 1) the extensional regime under the anticlinal ridge crest caused the initiation of localized fault zones, acting as fluid conduits in the gas hydrate stability zone (GHSZ). 2) sediment deformation induced by focused fluid flow and massive growth and dissolution of gas hydrate, similar to processes controlling the evolution of pockmarks on the Nigerian continental margin. We suggest that these processes may be responsible for the formation of a massive hydrate core in the crest of the anticline, as inferred from other geophysical datasets. Triggering process for fluid migration cannot be clearly defined. However, the existence of blind thrust faults may help to advect deep-seated fluids. This may be augmented by biogenic production of shallow gas underneath the ridge, where the excess of gas enables the coexistence of gas, water, and gas hydrate within the GHSZ. Fluid migration structures may exists because of the buoyancy of gas-bearing fluids. This study shows a potential model on how gas-bearing fluids migrate upward towards structural highs, which might occur in other anticlinal structures around the world. Keywords: P-Cable, gas-hydrate, fluid flow, fault-related fold, methane seepage

Rapid Ice Mass Loss: Does It Have an Influence on Earthquake Occurrence in Southern Alaska?

NASA Technical Reports Server (NTRS)

Sauber, Jeanne M.

2008-01-01

The glaciers of southern Alaska are extensive, and many of them have undergone gigatons of ice wastage on time scales on the order of the seismic cycle. Since the ice loss occurs directly above a shallow main thrust zone associated with subduction of the Pacific-Yakutat plate beneath continental Alaska, the region between the Malaspina and Bering Glaciers is an excellent test site for evaluating the importance of recent ice wastage on earthquake faulting potential. We demonstrate the influence of cumulative glacial mass loss following the 1899 Yakataga earthquake (M=8.1) by using a two dimensional finite element model with a simple representation of ice fluctuations to calculate the incremental stresses and change in the fault stability margin (FSM) along the main thrust zone (MTZ) and on the surface. Along the MTZ, our results indicate a decrease in FSM between 1899 and the 1979 St. Elias earthquake (M=7.4) of 0.2 - 1.2 MPa over an 80 km region between the coast and the 1979 aftershock zone; at the surface, the estimated FSM was larger but more localized to the lower reaches of glacial ablation zones. The ice-induced stresses were large enough, in theory, to promote the occurrence of shallow thrust earthquakes. To empirically test the influence of short-term ice fluctuations on fault stability, we compared the seismic rate from a reference background time period (1988-1992) against other time periods (1993-2006) with variable ice or tectonic change characteristics. We found that the frequency of small tectonic events in the Icy Bay region increased in 2002-2006 relative to the background seismic rate. We hypothesize that this was due to a significant increase in the rate of ice wastage in 2002-2006 instead of the M=7.9, 2002 Denali earthquake, located more than 100km away.

Structure, Quaternary history, and general geology of the Corral Canyon area, Los Angeles County, California

USGS Publications Warehouse

Yerkes, R.F.; Wentworth, Carl M.

1965-01-01

The Corral Canyon nuclear power plant site consists of about 305 acres near the mouth of Corral Canyon in the central Santa Monica Mountains; it is located on an east-trending segment of the Pacific Coast between Point Dume and Malibu Canyon, about 28 miles due west of Los Angeles. The Santa Monica Mountains are the southwesternmost mainland part of the Transverse Ranges province, the east-trending features of which transect the otherwise relatively uniform northwesterly trend of the geomorphic and geologic features of coastal California. The south margin of the Transverse Ranges is marked by the Santa Monica fault system, which extends eastward near the 34th parallel for at least 145 miles from near Santa Cruz Island to the San Andreas fault zone. In the central Santa Monica Mountains area the Santa Monica fault system includes the Malibu Coast fault and Malibu Coast zone of deformation on the north; from the south it includes an inferred fault--the Anacapa fault--considered to follow an east-trending topographic escarpmemt on the sea floor about 5 miles south of the Malibu Coast fault. The low-lying terrain south of the fault system, including the Los Angeles basin and the largely submerged Continental Borderland offshore, are dominated by northwest-trending structural features. The Malibu Coat zone is a wide, east-trending band of asymmetrically folded, sheared, and faulted bedrock that extends for more than 20 miles along the north margin of the Santa Monica fault system west of Santa Monica. Near the north margin of the Malibu Coast zone the north-dipping, east-trending Malibu Coast fault juxtaposes unlike, in part contemporaneous sedimentary rock sections; it is inferred to be the near-surface expression of a major crustal boundary between completely unrelated basement rocks. Comparison of contemporaneous structural features and stratigraphic sections (Late Cretaceous to middle Miocene sedimentary, rocks and middle Miocene volcanic and intrusive igneous rocks on the north; middle and upper Miocene sedimentary and middle Miocene volcanic rocks on the south) across the fault demonstrates that neither strike slip of less than 25 miles nor high-angle dip slip can account for this juxtaposition. Instead, the Malibu Coast fault is inferred to have been the locus of large-magnitude, north-south oriented, horizontal shortening (north, or upper, block thrust over south block). This movement occurred at or near the northern boundary of the Continental Borderland, the eastern boundary of which is inferred to be the northwest-trending known-active Newport-Inglewood zone of en echelon right lateral strike-slip faults in the western Los Angeles basin. Local structural features and their relation to regional features, such as those in the Malibu Coast zone, form the basis for the interpretation that the Malibu Coast fault has acted chiefly as a thrust fault. Within the Malibu Coast zone, on both sides of the Malibu Coast fault, structural features in rocks that range in age from Late Cretaceous to late Miocene are remarkably uniform in orientation. The predominant trend of bedding, axial surfaces of numerous asymmetric folds, locally pervasive shear surfaces, and faults is approximately east-west and their predominant dip is northward.. The axes of the folds plunge gently east or west. Evidence from faults and shears within the zone indicates that relative movement on most of these was north (upper) over south. Beyond the Malibu Coast zone to the north and south the rocks entirely lack the asymmetric folds, overturned beds, and the locally abundant shears that characterize the rocks within the zone; these rocks were therefore not subjected to the same deforming forces that existed near the Malibu Coast fault. Movement on the Malibu Coast fault and deformation in the Malibu Coast zone occurred chiefly during the interval between late Miocene and late Pleistocene time. The youngest-known faulting in the Malibu Coast zone is late Pl

Neotectonic reactivation of shear zones and implications for faulting style and geometry in the continental margin of NE Brazil

NASA Astrophysics Data System (ADS)

Bezerra, F. H. R.; Rossetti, D. F.; Oliveira, R. G.; Medeiros, W. E.; Neves, B. B. Brito; Balsamo, F.; Nogueira, F. C. C.; Dantas, E. L.; Andrades Filho, C.; Góes, A. M.

2014-02-01

The eastern continental margin of South America comprises a series of rift basins developed during the breakup of Pangea in the Jurassic-Cretaceous. We integrated high resolution aeromagnetic, structural and stratigraphic data in order to evaluate the role of reactivation of ductile, Neoproterozoic shear zones in the deposition and deformation of post-rift sedimentary deposits in one of these basins, the Paraíba Basin in northeastern Brazil. This basin corresponds to the last part of the South American continent to be separated from Africa during the Pangea breakup. Sediment deposition in this basin occurred in the Albian-Maastrichtian, Eocene-Miocene, and in the late Quaternary. However, our investigation concentrates on the Miocene-Quaternary, which we consider the neotectonic period because it encompasses the last stress field. This consisted of an E-W-oriented compression and a N-S-oriented extension. The basement of the basin forms a slightly seaward-tilted ramp capped by a late Cretaceous to Quaternary sedimentary cover ~ 100-400 m thick. Aeromagnetic lineaments mark the major steeply-dipping, ductile E-W- to NE-striking shear zones in this basement. The ductile shear zones mainly reactivated as strike-slip, normal and oblique-slip faults, resulting in a series of Miocene-Quaternary depocenters controlled by NE-, E-W-, and a few NW-striking faults. Faulting produced subsidence and uplift that are largely responsible for the present-day morphology of the valleys and tablelands in this margin. We conclude that Precambrian shear zone reactivation controlled geometry and orientation, as well as deformation of sedimentary deposits, until the Neogene-Quaternary.

Neogene evolution of northern Mahakam Delta, East Kalimantan, Indonesia

DOE Office of Scientific and Technical Information (OSTI.GOV)

Armin, R.A.; Abdoerrias, R.; Boer, W.D. de

1996-01-01

A regional sequence-stratigraphic study of the lower Kutei basin, embracing present coastal and offshore East Kalimantan, was undertaken to decipher the Neogene history of an important oil-producing province. The chronostratigraphic framework developed during this study was applied to facies analyses, organic geochemistry, and 2-D basin modeling. Integration of these disciplines powerfully illuminated the relationships between structuring, sedimentation, and hydrocarbon migration, Sedimentation in the lower Kutei basin since the late Middle Miocene has been dominated by the tidal-fluvial Mahakam delta system. During this time the principal river transport system has remained in about the same location as the present-day Mahakam River.more » Thick successions of monotonously similar deltaic facies were stacked vertically, punctuated by progradational or backstepping (flooding) units. Middle to Upper Miocene shelf edges of the delta platform, which are commonly sites of carbonate buildups, offlap from west to east towards the present-day shelf edge. Growth faults active during ca. 12-9 Ma are clustered just basinward of a prominent aggradational Middle Miocene shelf margin, and they exerted profound control on facies distribution. Tectonic quiescence prevailed during ca. 9-4 Ma, and in this period widespread regressive deltaic deposition over a broad, stable delta platform created the most important reservoirs. Subsequently, during Late Pliocene and younger time, many early growth faults were reactivated, and new faults also formed eastward toward the present shelf margin. Here, economically significant intervals consist mainly of lowstand deposits that accumulated in shelf-margin half-grabens created by these Plio-Pleistocene faults.« less

Neogene evolution of northern Mahakam Delta, East Kalimantan, Indonesia

DOE Office of Scientific and Technical Information (OSTI.GOV)

Armin, R.A.; Abdoerrias, R.; Boer, W.D. de

1996-12-31

A regional sequence-stratigraphic study of the lower Kutei basin, embracing present coastal and offshore East Kalimantan, was undertaken to decipher the Neogene history of an important oil-producing province. The chronostratigraphic framework developed during this study was applied to facies analyses, organic geochemistry, and 2-D basin modeling. Integration of these disciplines powerfully illuminated the relationships between structuring, sedimentation, and hydrocarbon migration, Sedimentation in the lower Kutei basin since the late Middle Miocene has been dominated by the tidal-fluvial Mahakam delta system. During this time the principal river transport system has remained in about the same location as the present-day Mahakam River.more » Thick successions of monotonously similar deltaic facies were stacked vertically, punctuated by progradational or backstepping (flooding) units. Middle to Upper Miocene shelf edges of the delta platform, which are commonly sites of carbonate buildups, offlap from west to east towards the present-day shelf edge. Growth faults active during ca. 12-9 Ma are clustered just basinward of a prominent aggradational Middle Miocene shelf margin, and they exerted profound control on facies distribution. Tectonic quiescence prevailed during ca. 9-4 Ma, and in this period widespread regressive deltaic deposition over a broad, stable delta platform created the most important reservoirs. Subsequently, during Late Pliocene and younger time, many early growth faults were reactivated, and new faults also formed eastward toward the present shelf margin. Here, economically significant intervals consist mainly of lowstand deposits that accumulated in shelf-margin half-grabens created by these Plio-Pleistocene faults.« less

Structure and evolution of the eastern Gulf of Aden conjugate margins from seismic reflection data

NASA Astrophysics Data System (ADS)

d'Acremont, Elia; Leroy, Sylvie; Beslier, Marie-Odile; Bellahsen, Nicolas; Fournier, Marc; Robin, Cécile; Maia, Marcia; Gente, Pascal

2005-03-01

The Gulf of Aden is a young and narrow oceanic basin formed in Oligo-Miocene time between the rifted margins of the Arabian and Somalian plates. Its mean orientation, N75°E, strikes obliquely (50°) to the N25°E opening direction. The western conjugate margins are masked by Oligo-Miocene lavas from the Afar Plume. This paper concerns the eastern margins, where the 19-35 Ma breakup structures are well exposed onshore and within the sediment-starved marine shelf. Those passive margins, about 200 km distant, are non-volcanic. Offshore, during the Encens-Sheba cruise we gathered swath bathymetry, single-channel seismic reflection, gravity and magnetism data, in order to compare the structure of the two conjugate margins and to reconstruct the evolution of the thinned continental crust from rifting to the onset of oceanic spreading. Between the Alula-Fartak and Socotra major fracture zones, two accommodation zones trending N25°E separate the margins into three N110°E-trending segments. The margins are asymmetric: offshore, the northern margin is narrower and steeper than the southern one. Including the onshore domain, the southern rifted margin is about twice the breadth of the northern one. We relate this asymmetry to inherited Jurassic/Cretaceous rifts. The rifting obliquity also influenced the syn-rift structural pattern responsible for the normal faults trending from N70°E to N110°E. The N110°E fault pattern could be explained by the decrease of the influence of rift obliquity towards the central rift, and/or by structural inheritance. The transition between the thinned continental crust and the oceanic crust is characterized by a 40 km wide zone. Our data suggest that its basement is made up of thinned continental crust along the southern margin and of thinned continental crust or exhumed mantle, more or less intruded by magmatic rocks, along the northern margin.

Lower crustal strength controls on melting and type of oceanization at magma-poor margins

NASA Astrophysics Data System (ADS)

Ros, E.; Perez-Gussinye, M.; Araujo, M. N.; Thoaldo Romeiro, M.; Andres-Martinez, M.; Morgan, J. P.

2017-12-01

Geodynamical models have been widely used to explain the variability in the architectonical style of conjugate rifted margins as a combination of lithospheric deformation modes, which are strongly influenced by lower crustal strength. We use 2D numerical models to show that the lower crustal strength also plays a key role on the onset and amount of melting and serpentinization during continental rifting. The relative timing between melting and serpentinization onsets controls whether the continent-ocean transition (COT) of margins will be predominantly magmatic or will mainly consist of exhumed and serpentinized mantle. Based on our results for magma-poor continental rifting, we propose a genetic link between margin architecture and COT styles that can be used as an additional tool to help interpret and understand the processes leading to margin formation. Our results show that strong lower crusts and very slow extension velocities (<5 mm/yr) lead to either symmetric or asymmetric margins with large oceanward dipping faults, strong syn-rift subsidence and abrupt crustal tapering beneath the continental shelf. These margins are characterized by a COT consisting of exhumed and serpentinized mantle and some magmatic products. Weak lower crusts at ultra-slow velocities lead also to either symmetric or asymmetric margins with small faults dipping both ocean- and landward, small syn-rift subsidence and gentle crustal tapering, and present a predominantly magmatic COT, perhaps underlain by some serpentinized mantle. When conjugate margins are asymmetric, if the rheology is relatively strong, serpentinite predominantly underlays the wide margin, whereas if the lower crustal strength is weak, melt preferentially migrates towards the wide margin. Based on the onshore lithospheric structure, extension velocity and margin architecture of the magma-poor section of the South Atlantic, we suggest that the COT of the northern sector, Camamu-Gabon basins, is more likely to consist of exhumed mantle with intruded magmatism, while to the South, the Camamu-Kwanza and North Santos-South Kwanza conjugates, may be better characterized by a predominantly magmatic COT.

Using the salt tectonics as a proxy to reveal post-rift active crustal tectonics: The example of the Eastern Sardinian margin

NASA Astrophysics Data System (ADS)

Lymer, Gaël; Vendeville, Bruno; Gaullier, Virginie; Chanier, Frank; Gaillard, Morgane

2017-04-01

The Western Tyrrhenian Basin, Mediterranean Sea, is a fascinating basin in terms of interactions between crustal tectonics, salt tectonics and sedimentation. The METYSS (Messinian Event in the Tyrrhenian from Seismic Study) project is based on 2100 km of HR seismic data acquired in 2009 and 2011 along the Eastern Sardinian margin. The main aim is to study the Messinian Salinity Crisis (MSC) in the Western Tyrrhenian Basin, but we also investigate the thinning processes of the continental crust and the timing of crustal vertical motions across this complex domain. Our first results allowed us to map the MSC seismic markers and to better constrain the timing of the rifting, which ended before the MSC across the upper and middle parts of the margin. We also evidenced that crustal activity persisted long after the end of rifting. This has been particularly observed on the upper margin, where several normal faults and a surprising compressional structure were recently active. In this study we investigate the middle margin, the Cornaglia Terrace, where the Mobile Unit (MU, mobile Messinian salt) accumulated during the MSC and acts as a décollement. Our goal is to ascertain whether or not crustal tectonics existed after the pre-MSC rift. This is a challenge where the MU is thick, because potential basement deformations could be first accommodated by the MU and therefore would not find any expression in the supra-salt layers (Upper Unit, UU and Plio-Quaternary, PQ). However our investigations clearly reveal interactions between crustal and salt tectonics along the margin. We thus evidence gravity gliding of the salt and its brittle sedimentary cover along basement slopes generated by the post-MSC tilting of some basement blocks bounded by crustal normal faults, formerly due to the rifting. Another intriguing structure also got our interest. It corresponds to a wedge-shaped of MU located in a narrow N-S half graben bounded to the west by a major, east-verging, crustal normal fault. Below the MU, the sediments thicken toward the fault. The top of the MU is sub-horizontal and the supra-salt layers are sub-horizontal. At a first glance this geometry would suggest that the pre-salt unit and the MU are syn-tectonic and that nothing happened after Messinian times. However some subtle evidence of deformations in the UU and PQ (an anticline to the west and a small west-verging normal fault in the east) imply that some crustal tectonics activity persisted after the end of the rifting. To understand why the salt unit is wedge-shaped, we considered several scenarii that we tested with physical modelling. We demonstrate that this structure is related to the post-rift activity of the major crustal normal fault, whose vertical motion has been cushioned by lateral flow of an initially tabular salt layer, which thinned upslope and inflated downslope, keeping the overlying sediments remained sub-horizontal. Such interactions between thin-skinned and thick-skinned tectonics highlight how the analysis of the salt tectonics is a powerful tool to reveal recent deep crustal tectonics in the Western Mediterranean Basin.

Cenozoic Tectonic Activity of the "Passive" North America Margin: Evidence for Cenozoic Activity on Mesozoic or Paleozoic Faults

NASA Astrophysics Data System (ADS)

Nedorub, O. I.; Knapp, C. C.

2012-12-01

The tectonic history of the Eastern North American Margin (ENAM) incorporates two cycles of continental assembly, multiple pulses of orogeny, rifting, and post-rift geodynamic evolution. This is reflected in the heterogeneous lithosphere of the ENAM which contains fault structures originated in Paleozoic to Mesozoic eras. The South Georgia Rift basin is probably the largest Mesozoic graben within its boundaries that is associated with the breakup of Pangea. It is composed of smaller sub-basins which appear to be bounded by high-angle normal faults, some of which may have been inverted in late Cretaceous and Cenozoic eras. Paleozoic structures may have been reactivated in Cenozoic time as well. The ENAM is characterized by N-NE maximum horizontal compressive stress direction. This maximum compressional stress field is sub-parallel to the strike of the Atlantic Coast province fault systems. Camden, Augusta, Allendale, and Pen Branch faults are four of the many such reactivated faults along the southern part of ENAM. These faults are now buried under the 0-400 m of loosely consolidated Cretaceous and Cenozoic age sediments and thus are either only partially mapped or currently not recognized. Some of the objectives of this study are to map the subsurface expression and geometry of these faults and to investigate the post Cretaceous deformation and possible causes of fault reactivation on a passive margin. This study employs an integrated geophysical approach to investigate the upper 200 m of identified locations of the above mentioned faults. 2-D high-resolution shallow seismic reflection and refraction methods, gravity surveys, GPR, 2-D electrical resistivity and well data are used for analyses and interpretation. Preliminary results suggest that Camden fault shows signs of Cenozoic reactivation through an approximately 30 m offset NW side up mainly along a steeply dipping fault zone in the basal contact of Coastal Plain sediments with the Carolina Piedmont. Drill-hole and seismic data along the Augusta profile show that there is a significant offset (approximately 7m) down to the SE of Pinehurst and older Cretaceous deposits. The Pen Branch fault seismic profile shows evidence of Cenozoic reactivation and inversion. The youngest discontinuous reflector (the top of the Dry Branch Formation) is offset by 1-4m and constrains the latest fault movement to be Middle Eocene in age. A NW-SE well derived cross-section across the Allendale fault shows that there is no significant offset above 50m below sea level (top of the Late Eocene Black Mingo Group), however a SW-NE cross section shows an approximately 21m offset NE side up across the newly postulated fault striking NW-SE. The top of the oldest undeformed formation (Middle Eocene Santee Limestone) and the top of the youngest deformed unit (Late Eocene Black Mingo Group) constrain a time frame for the latest deformation of the Coastal Plain sediments to be between approximately 50 and 40 Ma. The results of this research provide an opportunity to address the Cenozoic tectonism in SC, advance the knowledge and current understanding of the structure of the rift basins, update the database used for the ongoing CO2 sequestration project, the local hydrology, and the Savannah River Site safety evaluation.

Deformation record of 4-d accommodation of strain in the transition from transform to oblique convergent plate margin, southern Alaska (Invited)

NASA Astrophysics Data System (ADS)

Roeske, S.; Benowitz, J.; Enkelmann, E.; Pavlis, T. L.

2013-12-01

Crustal deformation at the transition from a dextral transform to subduction in the northern Cordillera is complicated by both the bend of the margin and the presence of low-angle subduction of an oceanic plateau, the Yakutat microplate, into the 'corner'. The dextral Denali Fault system located ~400 km inboard of the plate margin shows a similar transition from a dominantly strike-slip to transpressional regime as it curves to the west. Thermochronologic and structural studies in both areas indicate crustal response through the transition region is highly varied along and across strike. Previous thermochronology along the Fairweather fault SE of the St. Elias bend shows the most rapid exhumation occurs in close proximity to the fault, decreasing rapidly away from it. Enkelmann et al. (2010) and more recent detrital zircon FT (Falkowski et al., 2013 AGU abstract) show rapid and deep exhumation concentrated in the syntaxis, but over a fairly broad area continuing north beyond the Fairweather fault. Although the region is dominantly under ice, borders of the rapidly exhuming region appear to be previously identified major high-angle faults. This suggests that structures controlling the extreme exhumation may have significant oblique slip component, or, if flower structure, are reverse faults, and the region may be exhuming by transpression, with a significant component of pure shear. Southwest of the syntaxis, where convergence dominates over strike-slip, thin-skinned fold-and-thrust belts in the Yakutat microplate strata account for the shortening. The long-term record of convergence in this area is more cryptic due to sediment recycling through deep underplating and/or limited exhumation by upper crustal shortening, but a wide range of thermochronologic studies suggests that initial exhumation in the region began ~ 30 Ma and most rapid exhumation in the syntaxis began ~ 5 Ma. In the eastern Alaska Range a significant component of strike-slip, in addition to convergence, has been accommodated along the Denali Fault since E. Miocene. Southeast of the bend there is little evidence of convergence across the fault and Quaternary slip is ~12-13.5 mm/year. The eastern restraining bend of the Denali fault is much broader than the syntaxis and dextral slip continues at rates of ~10 mm/year, but the rock response to increasing obliquity is similar. Low and moderate-T cooling histories determined from a wide range of isotopic systems on minerals from bedrock show exhumation strongly localized on the north side of the high-angle Denali fault, south of the Hines Creek fault, since ~25 Ma. The structural record in ductilely deformed rocks from the most highly exhumed regions shows transpressive deformation over a few km wide region, but above the brittle-ductile transition strain becomes highly partitioned and is accommodated by thrust and normal faults on the north side of the bend. A connector fault between the Fairweather and Totschunda-Denali fault systems has been speculated on but it is not clear whether a single through-going fault is expressed at the surface. Any connector is likely a relatively young structure compared to the Fairweather and Denali systems' histories of long-lived oblique convergence. Overall, in both regions high-angle faults appear to be critical for controlling the location of major deep-seated and/or long-lived exhumation, and deformation at these geometrical complexities is dominated by transpression.

Structure of the Hat Creek graben region: Implications for the structure of the Hat Creek graben and transfer of right-lateral shear from the Walker Lane north of Lassen Peak, northern California, from gravity and magnetic anomalies

USGS Publications Warehouse

Langenheim, Victoria; Jachens, Robert C.; Clynne, Michael A.; Muffler, L. J. Patrick

2016-01-01

Interpretation of magnetic and new gravity data provides constraints on the geometry of the Hat Creek Fault, the amount of right-lateral offset in the area between Mt. Shasta and Lassen Peak, and confirmation of the influence of pre-existing structure on Quaternary faulting. Neogene volcanic rocks coincide with short-wavelength magnetic anomalies of both normal and reversed polarity, whereas a markedly smoother magnetic field occurs over the Klamath Mountains and its Paleogene cover. Although the magnetic field over the Neogene volcanic rocks is complex, the Hat Creek Fault, which is one of the most prominent normal faults in the region and forms the eastern margin of the Hat Creek Valley, is marked by the eastern edge of a north-trending magnetic and gravity high 20-30 km long. Modeling of these anomalies indicates that the fault is a steeply dipping (~75-85°) structure. The spatial relationship of the fault as modeled by the potential-field data, the youngest strand of the fault, and relocated seismicity suggests that deformation continues to step westward across the valley, consistent with a component of right-lateral slip in an extensional environment. Filtered aeromagnetic data highlight a concealed magnetic body of Mesozoic or older age north of Hat Creek Valley. The body’s northwest margin strikes northeast and is linear over a distance of ~40 km. Within the resolution of the aeromagnetic data (1-2 km), we discern no right-lateral offset of this body. Furthermore, Quaternary faults change strike or appear to end, as if to avoid this concealed magnetic body and to pass along its southeast edge, suggesting that pre-existing crustal structure influenced younger faulting, as previously proposed based on gravity data.

Evolution, distribution, and characteristics of rifting in southern Ethiopia

NASA Astrophysics Data System (ADS)

Philippon, Melody; Corti, Giacomo; Sani, Federico; Bonini, Marco; Balestrieri, Maria-Laura; Molin, Paola; Willingshofer, Ernst; Sokoutis, Dimitrios; Cloetingh, Sierd

2014-04-01

Southern Ethiopia is a key region to understand the evolution of the East African rift system, since it is the area of interaction between the main Ethiopian rift (MER) and the Kenyan rift. However, geological data constraining rift evolution in this remote area are still relatively sparse. In this study the timing, distribution, and style of rifting in southern Ethiopia are constrained by new structural, geochronological, and geomorphological data. The border faults in the area are roughly parallel to preexisting basement fabrics and are progressively more oblique with respect to the regional Nubia-Somalia motion proceeding southward. Kinematic indicators along these faults are mainly dip slip, pointing to a progressive rotation of the computed direction of extension toward the south. Radiocarbon data indicate post 30 ka faulting at both western and eastern margins of the MER with limited axial deformation. Similarly, geomorphological data suggest recent fault activity along the western margins of the basins composing the Gofa Province and in the Chew Bahir basin. This supports that interaction between the MER and the Kenyan rift in southern Ethiopia occurs in a 200 km wide zone of ongoing deformation. Fault-related exhumation at ~10-12 Ma in the Gofa Province, as constrained by new apatite fission track data, occurred later than the ~20 Ma basement exhumation of the Chew Bahir basin, thus pointing to a northward propagation of the Kenyan rift-related extension in the area.

Dislocation models of interseismic deformation in the western United States

USGS Publications Warehouse

Pollitz, F.F.; McCrory, P.; Svarc, J.; Murray, J.

2008-01-01

The GPS-derived crustal velocity field of the western United States is used to construct dislocation models in a viscoelastic medium of interseismic crustal deformation. The interseismic velocity field is constrained by 1052 GPS velocity vectors spanning the ???2500-km-long plate boundary zone adjacent to the San Andreas fault and Cascadia subduction zone and extending ???1000 km into the plate interior. The GPS data set is compiled from U.S. Geological Survey campaign data, Plate Boundary Observatory data, and the Western U.S. Cordillera velocity field of Bennett et al. (1999). In the context of viscoelastic cycle models of postearthquake deformation, the interseismic velocity field is modeled with a combination of earthquake sources on ???100 known faults plus broadly distributed sources. Models that best explain the observed interseismic velocity field include the contributions of viscoelastic relaxation from faulting near the major plate margins, viscoelastic relaxation from distributed faulting in the plate interior, as well as lateral variations in depth-averaged rigidity in the elastic lithosphere. Resulting rigidity variations are consistent with reduced effective elastic plate thickness in a zone a few tens of kilometers wide surrounding the San Andreas fault (SAF) system. Primary deformation characteristics are captured along the entire SAF system, Eastern California Shear Zone, Walker Lane, the Mendocino triple junction, the Cascadia margin, and the plate interior up to ???1000 km from the major plate boundaries.

Seismicity During Continental Breakup in the Red Sea Rift of Northern Afar

NASA Astrophysics Data System (ADS)

Illsley-Kemp, Finnigan; Keir, Derek; Bull, Jonathan M.; Gernon, Thomas M.; Ebinger, Cynthia; Ayele, Atalay; Hammond, James O. S.; Kendall, J.-Michael; Goitom, Berhe; Belachew, Manahloh

2018-03-01

Continental rifting is a fundamental component of plate tectonics. Recent studies have highlighted the importance of magmatic activity in accommodating extension during late-stage rifting, yet the mechanisms by which crustal thinning occurs are less clear. The Red Sea rift in Northern Afar presents an opportunity to study the final stages of continental rifting as these active processes are exposed subaerially. Between February 2011 and February 2013 two seismic networks were installed in Ethiopia and Eritrea. We locate 4,951 earthquakes, classify them by frequency content, and calculate 31 focal mechanisms. Results show that seismicity is focused at the rift axis and the western marginal graben. Rift axis seismicity accounts for ˜64% of the seismic moment release and exhibits a swarm-like behavior. In contrast, seismicity at the marginal graben is characterized by high-frequency earthquakes that occur at a constant rate. Results suggest that the rift axis remains the primary locus of seismicity. Low-frequency earthquakes, indicative of magmatic activity, highlight the presence of a magma complex ˜12 km beneath Alu-Dalafilla at the rift axis. Seismicity at the marginal graben predominantly occurs on westward dipping, antithetic faults. Focal mechanisms show that this seismicity is accommodating E-W extension. We suggest that the seismic activity at the marginal graben is either caused by upper crustal faulting accommodating enhanced crustal thinning beneath Northern Afar or as a result of flexural faulting between the rift and plateau. This seismicity is occurring in conjunction with magmatic extension at the rift axis, which accommodates the majority of long-term extension.

Evolution of the continental margin of southern Spain and the Alboran Sea

USGS Publications Warehouse

Dillon, William P.; Robb, James M.; Greene, H. Gary; Lucena, Juan Carlos

1980-01-01

Seismic reflection profiles and magnetic intensity measurements were collected across the southern continental margin of Spain and the Alboran basin between Spain and Africa. Correlation of the distinct seismic stratigraphy observed in the profiles to stratigraphic information obtained from cores at Deep Sea Drilling Project site 121 allows effective dating of tectonic events. The Alboran Sea basin occupies a zone of motion between the African and Iberian lithospheric plates that probably began to form by extension in late Miocene time (Tortonian). At the end of Miocene time (end of Messinian) profiles show that an angular unconformity was cut, and then the strata were block faulted before subsequent deposition. The erosion of the unconformity probably resulted from lowering of Mediterranean sea level by evaporation when the previous channel between the Mediterranean and Atlantic was closed. Continued extension probably caused the block faulting and, eventually the opening of the present channel to the Atlantic through the Strait of Gibraltar and the reflooding of the Mediterranean. Minor tectonic movements at the end of Calabrian time (early Pleistocene) apparently resulted in minor faulting, extensive transgression in southeastern Spain, and major changes in the sedimentary environment of the Alboran basin. Active faulting observed at five locations on seismic profiles seems to form a NNE zone of transcurrent movement across the Alboran Sea. This inferred fault trend is coincident with some bathymetric, magnetic and seismicity trends and colinear with active faults that have been mapped on-shore in Morocco and Spain. The faults were probably caused by stresses related to plate movements, and their direction was modified by inherited fractures in the lithosphere that floors the Alboran Sea.

Crustal Structure and Evolution of the Eastern Himalayan Plate Boundary System, Northeast India

NASA Astrophysics Data System (ADS)

Mitra, S.; Priestley, K. F.; Borah, Kajaljyoti; Gaur, V. K.

2018-01-01

We use data from 24 broadband seismographs located south of the Eastern Himalayan plate boundary system to investigate the crustal structure beneath Northeast India. P wave receiver function analysis reveals felsic continental crust beneath the Brahmaputra Valley, Shillong Plateau and Mikir Hills, and mafic thinned passive margin transitional crust (basement layer) beneath the Bengal Basin. Within the continental crust, the central Shillong Plateau and Mikir Hills have the thinnest crust (30 ± 2 km) with similar velocity structure, suggesting a unified origin and uplift history. North of the plateau and Mikir Hills the crustal thickness increases sharply by 8-10 km and is modeled by ˜30∘ north dipping Moho flexure. South of the plateau, across the ˜1 km topographic relief of the Dawki Fault, the crustal thickness increases abruptly by 12-13 km and is modeled by downfaulting of the plateau crust, overlain by 13-14 km thick sedimentary layer/rocks of the Bengal Basin. Farther south, beneath central Bengal Basin, the basement layer is thinner (20-22 km) and has higher Vs (˜4.1 km s-1) indicating a transitional crystalline crust, overlain by the thickest sedimentary layer/rocks (18-20 km). Our models suggest that the uplift of the Shillong Plateau occurred by thrust faulting on the reactivated Dawki Fault, a continent margin paleorift fault, and subsequent back thrusting on the south dipping Oldham Fault, in response to flexural loading of the Eastern Himalaya. Our estimated Dawki Fault offset combined with timing of surface uplift of the plateau reveals a reasonable match between long-term uplift and convergence rate across the Dawki Fault with present-day GPS velocities.

Photograph of the Month

NASA Astrophysics Data System (ADS)

2015-04-01

For dykes, magma flow direction can be deciphered from various fabrics in the chilled margin (Correa-Gomez et al., 2001, JSG 23, 1415). This photograph represents part of a chilled margin of a appr. N- S trending dyke at Kharghar Hills, Mumbai, Maharashtra, India. The section is sub-vertical. The elongated grooves indicate flow of magma through a fault and the tapered grooves (arrows) connote the flow direction: towards the pointed end of the groove. The magma flowed towards the north in this case. Such fabrics of wall-magma interaction in the Deccan volcanic province prove that dykes injected along fault planes. 19° 2‧ 22.3″ N, 73° 3‧ 28.7″ E. Photograph Ayan Achyuta Misra, Mumbai, India.

Tectonic elements of the continental margin of East Antarctica, 38-164ºE

USGS Publications Warehouse

O'Brien, P.E.; Stagg, H.M.J.

2007-01-01

The East Antarctic continental margin from 38–164ºE is divided into western and eastern provinces that developed during the separation of India from Australia–Antarctica (Early Cretaceous) and Australia from Antarctica (Late Cretaceous). In the overlap between these provinces the geology is complex and bears the imprint of both extension/spreading episodes, with an overprinting of volcanism. The main rift-bounding faults appear to approximately coincide with the outer edge of the continental shelf. Inboard of these faults, the sedimentary cover thins above shallowing basement towards the coast where crystalline basement generally crops out. The continental slope and the landward flanks of the ocean basins, are blanketed by up to 9–10 km of mainly post-rift sediments in margin-parallel basins, except in the Bruce Rise area. Beneath this blanket, extensive rift basins are identified off Enderby and Wilkes Land/Terre Adélie; however, their extent and detailed structures are difficult to determine.

Cordilleran hingeline: Late Precambrian rifted margin of the North American craton and its impact on the depositional and structural history, Utah and Nevada

NASA Astrophysics Data System (ADS)

Picha, Frank; Gibson, Richard I.

1985-07-01

The structural pattern set by late Precambrian rifting and fragmentation of the North American continent is apparent in both sedimentary and tectonic trends in western Utah and eastern Nevada. The late Precambrian cratonic margin (Cordilleran hingeline) displays several prominent structural features, such as the Wasatch and Ancient Ephraim faults, Fillmore arch and northeast-trending lineaments, which were repeatedly reactivated as structural uplifts, ramps, strike-slip faults, and extensional detachments. The renewed activity affected, among others, the geometry of the late Paleozoic Ancestral Rocky Mountain uplifts and basins, the extent of the Jurassic Arapien basin, the sedimentary pattern of the Cretaceous foreland basin, the geometry of the Sevier orogenic belt, and the extent and type of Basin-and-Range extensional tectonics. The rifted cratonic margin has thus remained a major influence on regional structures long after rifting has ceased. *Present address: Everest Geotech, 10101 Southwest Freeway, Houston, Texas 77074

Sea-level-induced seismicity and submarine landslide occurrence

USGS Publications Warehouse

Brothers, Daniel S.; Luttrell, Karen M.; Chaytor, Jason D.

2013-01-01

The temporal coincidence between rapid late Pleistocene sea-level rise and large-scale slope failures is widely documented. Nevertheless, the physical mechanisms that link these phenomena are poorly understood, particularly along nonglaciated margins. Here we investigate the causal relationships between rapid sea-level rise, flexural stress loading, and increased seismicity rates along passive margins. We find that Coulomb failure stress across fault systems of passive continental margins may have increased more than 1 MPa during rapid late Pleistocene–early Holocene sea-level rise, an amount sufficient to trigger fault reactivation and rupture. These results suggest that sea-level–modulated seismicity may have contributed to a number of poorly understood but widely observed phenomena, including (1) increased frequency of large-scale submarine landslides during rapid, late Pleistocene sea-level rise; (2) emplacement of coarse-grained mass transport deposits on deep-sea fans during the early stages of marine transgression; and (3) the unroofing and release of methane gas sequestered in continental slope sediments.

Evolution of Northeast Atlantic Magmatic Continental Margins from an Ethiopian-Afar Perspective

NASA Astrophysics Data System (ADS)

England, R. W.; Cornwell, D. G.; Ramsden, A. M.

2014-12-01

One of the major problems interpreting the evolution of magmatic continental margins is that the structure which should record the pre-magmatic evolution of the rift and which potentially influences the character of the rifting process is partially or completely obscured by thick basalt lava flows and sills. A limited number of deep reflection seismic profiles acquired with tuned seismic sources have penetrated the basalts and provide an image of the pre-magmatic structure, otherwise the principle data are lower resolution wide-angle/refraction profiles and potential field models which have greater uncertainties associated with them. In order to sidestep the imaging constraints we have examined the Ethiopian - Afar rift system to try to understand the rifting process. The Main Ethiopian rift contains an embryonic magmatic passive margin dominated by faulting at the margins of the rift and en-echelon magmatic zones at the centre. Further north toward Afar the rift becomes in-filled with extensive lava flows fed from fissure systems in the widening rift zone. This rift system provides, along its length, a series of 'snapshots' into the possible tectonic evolution of a magmatic continental margin. Deep seismic profiles crossing the NE Atlantic margins reveal ocean dipping reflector sequences (ODRS) overlying extended crust and lower crustal sill complexes of intruded igneous rock, which extend back beneath the continental margin. The ODRS frequently occur in fault bounded rift structures along the margins. We suggest, by analogy to the observations that can be made in the Ethiopia-Afar rift that these fault bounded basins largely form at the embryonic rift stage and are then partially or completely filled with lavas fed from fissures which are now observed as the ODRS. Also in the seismic profiles we identify volcanic constructs on the ODRS which we interpret as the equivalent of the present day fissure eruptions seen in Afar. The ocean ward dip on the ODRS is predominantly the result of post-eruption differential subsidence, as opposed to syn-eruption extension. The timing of intrusion of the lower crustal sill complexes remains unclear but they are most likely to have been emplaced as the supply of magma increased, which implies they are a late stage addition.

Focal mechanisms and the stress regime in NE and SW Tanzania, East Africa

NASA Astrophysics Data System (ADS)

Brazier, Richard A.; Nyblade, Andrew A.; Florentin, Juliette

2005-07-01

We report 12 new focal mechanisms from earthquakes in NE and SW Tanzania where the stress regime within the East African rift system is not well constrained. Focal mechanisms for events at the intersection of the Lake Tanganyika and Rukwa rifts in SW Tanzania indicate a complicated stress pattern with possible dextral strike-slip motion on some faults but oblique motion on others (either sinistral on NW striking faults or dextral on NE striking faults). Within the Rukwa rift, focal mechanisms indicate normal dip-slip motion with NE-SW opening. In NE Tanzania where the Eastern rift impinges on the margin of the Tanzania Craton, fault motions are consistent with a zone of distributed block faults and sub E-W extension. All twelve earthquakes likely nucleated within the crust.

Variability of High Resolution Vp/Vs and Seismic Velocity Structure Along the Nicaragua/Costa Rica Segment of the Middle America Subduction Zone

NASA Astrophysics Data System (ADS)

Moore-Driskell, M. M.; DeShon, H. R.

2012-12-01

Previous studies of subduction zone earthquakes have shown that fault conditions control earthquake rupture and behavior. There are many potential properties that may vary along the subduction margin that could cause fault zone variability, including plate age, temperature, and/or geometry, convergence rate, state of hydration, overriding geology, subducting sediment packages, or subducting seamounts/ridges. The Nicaragua/Costa Rica segment of the Middle America subduction zone is highly variable along strike and down dip. We use this margin to examine how these variable conditions affect earthquake behavior by determining local ratios of compressional to shear wave velocities (Vp/Vs) and detailed seismic velocity structure. Vp/Vs is one of the best tools available to reliably define fault conditions because it is directly related to the Poisson's ratio of the fault material, and it is sensitive to the presence of fluids and changing permeability. Thus with well-resolved near source Vp/Vs measurements we can infer composition and/or high fluid pressures. Here, we use a technique developed by Lin and Shearer (2007) to determine local Vp/Vs in small areas (~2 x 2 x 2 km) with high seismicity. Within the seismogenic zone, we find the margin to be highly variable along strike in Vp/Vs and seismic velocity. These changes correlate to documented variability in incoming plate properties. Increased Vp/Vs is associated with intraplate earthquakes along Nicaragua and northern Costa Rica. We compare our results with other geophysical studies including new high-resolution images of seismic velocity structure, an extensive catalog of high quality relocated events, apparent stress calculations, coupling, and SSE/NVT occurrence. A better understanding of the connection between fault properties and earthquake behavior gives insight into the role of fluids in seismogenesis, the spectrum of earthquake rupture, and possible hazard at subduction zones.

Seismic images of the sliver strike-slip fault and back thrust in the Andaman-Nicobar region

NASA Astrophysics Data System (ADS)

Singh, Satish C.; Moeremans, Raphaele; McArdle, Jo; Johansen, Kjell

2013-10-01

sliver strike-slip Great Sumatra Fault (GSF) traverses mainland Sumatra from the Sunda Strait in the southeast to Banda Aceh in the northwest, and defines the present day plate boundary between the Sunda Plate in the north and the Burmese Sliver Plate in the south. It has been well studied on mainland Sumatra but poorly north of Banda Aceh in the Andaman Sea. Here we present deep seismic reflection images along the northward extension of the GSF over 700 km until it joins the Andaman Sea Spreading Centre, and we interpret these images in the light of earthquake, gravity, and bathymetry data. We find that the GSF has two strands between Banda Aceh and Nicobar Island: a transpression in the south and a deep narrow active rift system in the north, dotted with volcanoes in the center, suggesting that the volcanic arc is coincident with rifting. Farther north of Nicobar Island, an active strike-slip fault, the Andaman-Nicobar Fault, cuts through a rifted deep basin until its intersection with the Andaman Sea Spreading Centre. The volcanic arc lies just east of the rift basin. The western margin of this basin seems to be a rifted continental margin, tilted westward, and flooring the Andaman-Nicobar fore-arc basin. The Andaman-Nicobar fore-arc basin is bounded in the west by back thrusts similar to the West Andaman and Mentawai faults. The cluster of seismicity after the 2004 great Andaman-Sumatra earthquake just north of Nicobar Island coincides with the intersection of two strike-slip fault systems.

Stability of fault submitted to fluid injections

NASA Astrophysics Data System (ADS)

Brantut, N.; Passelegue, F. X.; Mitchell, T. M.

2017-12-01

Elevated pore pressure can lead to slip reactivation on pre-existing fractures and faults when the coulomb failure point is reached. From a static point of view, the reactivation of fault submitted to a background stress (τ0) is a function of the peak strength of the fault, i.e. the quasi-static effective friction coefficient (µeff). However, this theory is valid only when the entire fault is affected by fluid pressure, which is not the case in nature, and during human induced-seismicity. In this study, we present new results about the influence of the injection rate on the stability of faults. Experiments were conducted on a saw-cut sample of westerly granite. The experimental fault was 8 cm length. Injections were conducted through a 2 mm diameter hole reaching the fault surface. Experiments were conducted at four different order magnitudes fluid pressure injection rates (from 1 MPa/minute to 1 GPa/minute), in a fault system submitted to 50 and 100 MPa confining pressure. Our results show that the peak fluid pressure leading to slip depends on injection rate. The faster the injection rate, the larger the peak fluid pressure leading to instability. Wave velocity surveys across the fault highlighted that decreasing the injection-rate leads to an increase of size of the fluid pressure perturbation. Our result demonstrate that the stability of the fault is not only a function of the fluid pressure requires to reach the failure criterion, but is mainly a function of the ratio between the length of the fault affected by fluid pressure and the total fault length. In addition, we show that the slip rate increases with the background effective stress and with the intensity of the fluid pressure pertubation, i.e. with the excess shear stress acting on the part of the fault pertubated by fluid injection. Our results suggest that crustal fault can be reactivated by local high fluid overpressures. These results could explain the "large" magnitude human-induced earthquakes recently observed in Oklahoma (Mw 5.6, 2016).

Characterizing a large shear-zone with seismic and magnetotelluric methods: The case of the Dead Sea Transform

USGS Publications Warehouse

Maercklin, N.; Bedrosian, P.A.; Haberland, C.; Ritter, O.; Ryberg, T.; Weber, M.; Weckmann, U.

2005-01-01

Seismic tomography, imaging of seismic scatterers, and magnetotelluric soundings reveal a sharp lithologic contrast along a ???10 km long segment of the Arava Fault (AF), a prominent fault of the southern Dead Sea Transform (DST) in the Middle East. Low seismic velocities and resistivities occur on its western side and higher values east of it, and the boundary between the two units coincides partly with a seismic scattering image. At 1-4 km depth the boundary is offset to the east of the AF surface trace, suggesting that at least two fault strands exist, and that slip occurred on multiple strands throughout the margin's history. A westward fault jump, possibly associated with straightening of a fault bend, explains both our observations and the narrow fault zone observed by others. Copyright 2005 by the American Geophysical Union.

Early Proterozoic activity on Archean faults in the western Superior province - evidence from pseudotachylite

USGS Publications Warehouse

Peterman, Z.E.; Day, W.

1989-01-01

Major transcurrent faults in the Superior province developed in the Late Archean at the close of the Kenoran orogeny. Reactivation of some of these faults late in the Early Proterozoic is indicated by Rb-Sr analyses of pseudotachylite from the Rainy Lake-Seine River and Quetico faults in the Rainy Lake region of Minnesota and Ontario. Fault veins of pseudotachylite and immediately adjacent country rock at two localities yielded subparallel isochrons that are pooled for an age of 1947??23 Ma. K-Ar and Rb-Sr biotite ages register earlier regional cooling of the terrane at about 2500 Ma with no evidence of younger thermal overprinting at temperatures exceeding 300??C. Accordingly, the 1947??23 Ma age is interpreted as dating the formation of the pseudotachylite. Reactivation of existing faults at this time was caused by stresses transmitted from margins of the Superior province where compressional tectonic events were occurring. -Authors

Mountain front migration and drainage captures related to fault segment linkage and growth: The Polopos transpressive fault zone (southeastern Betics, SE Spain)

NASA Astrophysics Data System (ADS)

Giaconia, Flavio; Booth-Rea, Guillermo; Martínez-Martínez, José Miguel; Azañón, José Miguel; Pérez-Romero, Joaquín; Villegas, Irene

2013-01-01

The Polopos E-W- to ESE-WNW-oriented dextral-reverse fault zone is formed by the North Alhamilla reverse fault and the North and South Gafarillos dextral faults. It is a conjugate fault system of the sinistral NNE-SSW Palomares fault zone, active from the late most Tortonian (≈7 Ma) up to the late Pleistocene (≥70 ky) in the southeastern Betics. The helicoidal geometry of the fault zone permits to shift SE-directed movement along the South Cabrera reverse fault to NW-directed shortening along the North Alhamilla reverse fault via vertical Gafarillos fault segments, in between. Since the Messinian, fault activity migrated southwards forming the South Gafarillos fault and displacing the active fault-related mountain-front from the north to the south of Sierra de Polopos; whilst recent activity of the North Alhamilla reverse fault migrated westwards. The Polopos fault zone determined the differential uplift between the Sierra Alhamilla and the Tabernas-Sorbas basin promoting the middle Pleistocene capture that occurred in the southern margin of the Sorbas basin. Continued tectonic uplift of the Sierra Alhamilla-Polopos and Cabrera anticlinoria and local subsidence associated to the Palomares fault zone in the Vera basin promoted the headward erosion of the Aguas river drainage that captured the Sorbas basin during the late Pleistocene.

Synchronous changes in the rift-margin San Jose Island basin and initiation of the Alarcón spreading ridge: implications for rift to drift transition in the Gulf of California

NASA Astrophysics Data System (ADS)

Umhoefer, P. J.; Sutherland, F.; Kent, G.; Harding, A.; Lizarralde, D.; Fletcher, J.; Holbrook, W.; Axen, G.; González-Fernández, A.

2004-12-01

The rift to drift hypothesis is widely cited, but it well known in detail. The low sedimentation rate and recent rifting of the Gulf of California provides insight into the rift-to-drift process. Lizarralde et al. (2007) showed that the style of rifting, based on crustal structure, varies significantly between the central and southern Gulf of California, and this combined with the analysis of sedimentary basins shows the small-scale (~15 km) complexities of the rift-to-drift transition. The shut off of rifting on the eastern side of the plate boundary occurred at ca. 2 - 3 Ma (Aragon-Arreola etal, 2005, Aragon-Arreola & Martin-Barajas, 2007; our unpublished data). Many studies have shown that the western side of the Gulf is still active despite sea-floor spreading occurring on the Alarcón and other short spreading centers since 2 - 3 Ma. At the mouth of the Gulf, magnetic anomalies on the eastern side of the Alarcón rise show that it appears to have changed to seafloor spreading as early as 3.7 Ma. But comparatively, on the eastern side, magnetic anomalies do not indicate the formation of new oceanic crust until 2.5 Ma, so spreading was first fully established at 2.5 Ma. The San Jose Island basin (Umhoefer et al., 2007) began at approximately 4- 6 Ma; the basin had its most rapid subsidence, with faulting accompanying marine sedimentation, from 3.6 ± 0.5 Ma (Ar tuff age) to 2.5-2.4 Ma (forams). Basin margin faulting died and moved east (offshore) shortly after 2.5-2.4 Ma. Late Quaternary marine terraces suggest that faulting rates slowed by 1-2 orders of magnitude since the fault reorganization at 2.5 Ma. These observations suggest that the rift - drift transition started, but is not yet finished, on the western side of the Gulf of California, with low rates of faulting (<1? mm/yr) continuing on the continental margin for reasons that are not well understood. Our work highlights the importance of combining onshore field and MSC data and analyzing entire conjugate rifted margins to accurately assess rifting processes.

Synchronous changes in the rift-margin San Jose Island basin and initiation of the Alarcón spreading ridge: implications for rift to drift transition in the Gulf of California

NASA Astrophysics Data System (ADS)

Umhoefer, P. J.; Sutherland, F.; Kent, G.; Harding, A.; Lizarralde, D.; Fletcher, J.; Holbrook, W.; Axen, G.; González-Fernández, A.

2007-12-01

The rift to drift hypothesis is widely cited, but it well known in detail. The low sedimentation rate and recent rifting of the Gulf of California provides insight into the rift-to-drift process. Lizarralde et al. (2007) showed that the style of rifting, based on crustal structure, varies significantly between the central and southern Gulf of California, and this combined with the analysis of sedimentary basins shows the small-scale (~15 km) complexities of the rift-to-drift transition. The shut off of rifting on the eastern side of the plate boundary occurred at ca. 2 - 3 Ma (Aragon-Arreola etal, 2005, Aragon-Arreola & Martin-Barajas, 2007; our unpublished data). Many studies have shown that the western side of the Gulf is still active despite sea-floor spreading occurring on the Alarcón and other short spreading centers since 2 - 3 Ma. At the mouth of the Gulf, magnetic anomalies on the eastern side of the Alarcón rise show that it appears to have changed to seafloor spreading as early as 3.7 Ma. But comparatively, on the eastern side, magnetic anomalies do not indicate the formation of new oceanic crust until 2.5 Ma, so spreading was first fully established at 2.5 Ma. The San Jose Island basin (Umhoefer et al., 2007) began at approximately 4- 6 Ma; the basin had its most rapid subsidence, with faulting accompanying marine sedimentation, from 3.6 ± 0.5 Ma (Ar tuff age) to 2.5-2.4 Ma (forams). Basin margin faulting died and moved east (offshore) shortly after 2.5-2.4 Ma. Late Quaternary marine terraces suggest that faulting rates slowed by 1-2 orders of magnitude since the fault reorganization at 2.5 Ma. These observations suggest that the rift - drift transition started, but is not yet finished, on the western side of the Gulf of California, with low rates of faulting (<1? mm/yr) continuing on the continental margin for reasons that are not well understood. Our work highlights the importance of combining onshore field and MSC data and analyzing entire conjugate rifted margins to accurately assess rifting processes.

Rotor Design Options for Improving XV-15 Whirl-Flutter Stability Margins

NASA Technical Reports Server (NTRS)

Acree, C. W., Jr.; Peyran, R. J.; Johnson, Wayne

2004-01-01

Rotor design changes intended to improve tiltrotor whirl-flutter stability margins were analyzed. A baseline analytical model of the XV-15 was established, and then a thinner, composite wing was designed to be representative of a high-speed tiltrotor. The rotor blade design was modified to increase the stability speed margin for the thin-wing design. Small rearward offsets of the aerodynamic-center locus with respect to the blade elastic axis created large increases in the stability boundary. The effect was strongest for offsets at the outboard part of the blade, where an offset of the aerodynamic center by 10% of tip chord improved the stability margin by over 100 knots. Forward offsets of the blade center of gravity had similar but less pronounced effects. Equivalent results were seen for swept-tip blades. Appropriate combinations of sweep and pitch stiffness completely eliminated whirl flutter within the speed range examined; alternatively, they allowed large increases in pitch-flap coupling (delta-three) for a given stability margin. A limited investigation of the rotor loads in helicopter and airplane configuration showed only minor increases in loads.

Stability evaluation of short-circuiting gas metal arc welding based on ensemble empirical mode decomposition

NASA Astrophysics Data System (ADS)

Huang, Yong; Wang, Kehong; Zhou, Zhilan; Zhou, Xiaoxiao; Fang, Jimi

2017-03-01

The arc of gas metal arc welding (GMAW) contains abundant information about its stability and droplet transition, which can be effectively characterized by extracting the arc electrical signals. In this study, ensemble empirical mode decomposition (EEMD) was used to evaluate the stability of electrical current signals. The welding electrical signals were first decomposed by EEMD, and then transformed to a Hilbert-Huang spectrum and a marginal spectrum. The marginal spectrum is an approximate distribution of amplitude with frequency of signals, and can be described by a marginal index. Analysis of various welding process parameters showed that the marginal index of current signals increased when the welding process was more stable, and vice versa. Thus EEMD combined with the marginal index can effectively uncover the stability and droplet transition of GMAW.

Mineral, Virginia earthquake illustrates seismicity of a passive-aggressive margin

NASA Astrophysics Data System (ADS)

Stein, S. A.; Pazzaglia, F. J.; Meltzer, A.; Berti, C.; Wolin, E.; Kafka, A. L.

2011-12-01

The August 2011 M5.8 Virginia earthquake illustrated again that "passive" continental margins, at which the continent and neighboring seafloor are part of the same plate, are often seismically active. This phenomenon occurs worldwide, with the east coast of North America a prime example. Examples from North to South include the 1933 M 7.3 Baffin Bay, 1929 M 7.2 Grand Banks of Newfoundland, 1755 M 6 Cape Ann, Massachusetts, and 1886 M 7 Charleston earthquakes. The mechanics of these earthquakes remains unclear. Their overall alignment along the margin suggests that they reflect reactivation of generally margin-parallel faults remaining from continental convergence and later rifting by the modern stress field. This view accords with the occurrence of the Virginia earthquake by reverse faulting on a margin-parallel NE-SW striking fault. However, it occurred on the northern edge of the central Virginia seismic zone, a seismic trend normal to the fault plane, margin, and associated structures, that has no clear geologic expression. Hence it is unclear why this and similar seismic zones have the geometry they do. Although it is tempting to correlate these zones with extensions of Atlantic fracture zones, this correlation has little explanatory power given the large number of such zones. It is similarly unclear whether these zones and the intervening seismic gaps reflect areas that are relatively more active over time, or are instead the present loci of activity that migrates. It is also possible that the presently-active zones reflect long-lived aftershocks of large prehistoric earthquakes. The forces driving the seismicity are also unclear. In general, seismic moment release decreases southward along the margin, consistent with the variation in vertical motion rates observed by GPS, suggesting that glacial-isostatic adjustment (GIA) provides some of the stresses involved. However, in the mid-Atlantic region - south of the area of significant GIA - deformed stratigraphic and geomorphic markers, localized high-relief topography, and rapid river incision show uplift of the Piedmont and Appalachians relative to the Coastal Plain for the past 10 Ma, suggesting that the seismicity reflects active and long-term deformation. These challenging questions are natural candidates for further study using new seismological and GPS data from the EarthScope program, together with geological and modeling studies. The dense deployment of seismometers in the wake of the Mineral VA earthquake and the arrival of EarthScope on the eastern seaboard in 2012 and 2013 can provide the required observations at multiple scales to better understand the mechanics of and forces driving east coast seismicity. Here we begin this study by comparing the aftershock sequence of the Mineral VA earthquake to previously recorded events in the Reading Lancaster Seismic Zone and the Central Virginia Seismic Zone.

Comparison of the tectonics and geophysics of the major structural belts between the northern and southern continental margins of the South China Sea

NASA Astrophysics Data System (ADS)

Xia, Kan-yuan; Huang, Ci-liu; Jiang, Shao-ren; Zhang, Yi-xiang; Su, Da-quan; Xia, Si-gao; Chen, Zhong-rong

1994-07-01

A comparison of the tectonics and geophysics of the major structural belts of the northern and the southern continental margins of South China Sea has been made, on the basis of measured geophysical data obtained by ourselves over a period of 8 years (1984-1991). This confirmed that the northern margin is a divergent one and the southern margin is characterized by clearly convergent features. The main extensional structures of the northern margin are, from north to south: (1) The Littoral Fault Belt, a tectonic boundary between the continental crust and a transitional zone, along the coast of the provinces of Guangdong and Fujian in South China. It is characterised by earthquake activities, high magnetic anomalies and a rapid change in crustal thickness. (2) The Northern and Southern Depression zones (i.e., the Pearl River Mouth Basin), this strikes NE-ENE and is a very large Cenozoic depression which extends from offshore Shantou westwards to Hainan Island. (3) The Central Uplift Zone. This includes the Dongsha Uplift, Shenhu Uplift and may be linked with the Penghu uplift and Taiwan shoals to the east, forming a large NE-striking uplift zone along the northern continental slope. It is characterized by high magnetic anomalies. (4) Southern Boundary Fault Belt of the transitional crust. This has positive gravity anomalies on the land side and negative ones on the sea side. (5) The Magnetic Quiet Zone. This is located south of the southern Boundary Fault Belt and between the continental margin and the Central Basin of the South China Sea. Magnetic anomalies in this belt are of small amplitude and low gradient. We consider the Magnetic Quiet Zone to be a very important tectonic zone. The major structures of southern continental margin southwards are: (1) The Northern Fault Belt of the Nansha Block. This extends along the continental slope north of the Liyue shoal (Reed Bank) and Zhongye reef, and is a tectonic boundary between oceanic crust and the Nansha Block continental crust. (2) The Nansha Block Uplift Zone. Due to the development of reefs and shoals, there are many channels and valleys. Our long-distance multichannel seismic profiles indicated that there are thick Paleogene sediments and thin Neogene sediments all over the central part of the block. (3) The Nansha Trough, a nappe structure formed by the southeastward drifting of Nansha Block and northwestward overthrusting of Palawan-northwest Borneo. (4) Zengmu Shoal Basin, southwest of the Nansha Block; the maximum thickness of Cenozoic strata is over 9 km in this important petroliferous basin.

Crustal structure and extension mode in the northwestern margin of the South China Sea

NASA Astrophysics Data System (ADS)

Gao, Jinwei; Wu, Shiguo; McIntosh, Kirk; Mi, Lijun; Liu, Zheng; Spence, George

2016-06-01

Combining multi-channel seismic reflection and gravity modeling, this study has investigated the crustal structure of the northwestern South China Sea margin. These data constrain a hyper-extended crustal area bounded by basin-bounding faults corresponding to an aborted rift below the Xisha Trough with a subparallel fossil ridge in the adjacent Northwest Sub-basin. The thinnest crust is located in the Xisha Trough, where it is remnant lower crust with a thickness of less than 3 km. Gravity modeling also revealed a hyper-extended crust across the Xisha Trough. The postrift magmatism is well developed and more active in the Xisha Trough and farther southeast than on the northwestern continental margin of the South China Sea; and the magmatic intrusion/extrusion was relatively active during the rifting of Xisha Trough and the Northwest Sub-basin. A narrow continent-ocean transition zone with a width of ˜65 km bounded seaward by a volcanic buried seamount is characterized by crustal thinning, rift depression, low gravity anomaly and the termination of the break-up unconformity seismic reflection. The aborted rift near the continental margin means that there may be no obvious detachment fault like that in the Iberia-Newfoundland type margin. The symmetric rift, extreme hyper-extended continental crust and hotter mantle materials indicate that continental crust underwent stretching phase (pure-shear deformation), thinning phase and breakup followed by onset of seafloor spreading and the mantle-lithosphere may break up before crustal-necking in the northwestern South China Sea margin.

Testing thin-skinned inversion of a prerift salt-bearing passive margin (Eastern Prebetic Zone, SE Iberia)

NASA Astrophysics Data System (ADS)

Escosa, Frederic O.; Roca, Eduard; Ferrer, Oriol

2018-04-01

Detailed geologic mapping combined with well and seismic data from the Eastern Prebetic Zone (SE Iberia) reveal extensional and contractional structures that permit characterization of passive margin development and its incorporation into a thin-skinned fold-and-thrust belt. The study area is represented by NW-directed, ENE-trending folds and thrusts faults locally disrupted by the NW-trending Matamoros Basin and the active Jumilla and La Rosa diapirs. These structures resulted from the thin-skinned inversion of the proximal part of the Eastern South Iberian passive margin containing prerift salt. Here, Upper Jurassic to Santonian thick-skinned extension controlled the accumulation of sediment over mobile prerift salt. This in turn defined the style of salt tectonics characterized by monoclinal drape folds, suprasalt extensional faults and diapirs. The structural and sedimentological analysis suggests that during extension, salt localizes strain thus decoupling sub- and suprasalt deformation. Thick-skinned extension controls suprasalt deformation as well as its location and distribution which changes over time. Salt also localizes strain during inversion. The preexisting salt structures, weaker than adjacent areas, preferentially absorb the contractional deformation. In addition, the stepped subsalt geometry that results from thick-skinned extension also controls the shortening propagation. Therefore, the degree of strain localization depends on the thickness of the suprasalt cover and on the dip of subsalt faults relative to the thin-skinned transport direction.

Tectono-magmatic evolution at distal magma-poor rifted margins: insights of the lithospheric breakup at the Australia-Antarctica margins.

NASA Astrophysics Data System (ADS)

Gillard, Morgane; Autin, Julia; Manatschal, Gianreto

2015-04-01

The discovery of large domains of hyper-extended continental crust and exhumed mantle along many present-day magma-poor rifted margins questions the processes that play during the lithospheric breakup and the onset of seafloor spreading. In particular, the amount of magma and its relation to tectonic structures is yet little understood. Trying to find answers to these questions asks to work at the most distal parts of rifted margins where the transition from rifting to steady state seafloor spreading occurred. The Australian-Antarctic conjugated margins provide an excellent study area. Indeed, the central sector of the Great Australian Bight/Wilkes Land developed in a magma-poor probably ultra-slow setting and displays a complex and not yet well understood Ocean-Continent Transition (OCT). This distal area is well imaged by numerous high quality seismic lines covering the whole OCT and the steady-state oceanic crust. The deformation recorded in the sedimentary units along these margins highlights a migration of the deformation toward the ocean and a clear polyphase evolution. In particular, the observation that each tectono-sedimentary unit downlaps oceanwards onto the basement suggests that final rifting is associated with the creation of new depositional ground under conditions that are not yet those of a steady state oceanic crust. These observations lead to a model of evolution for these distal margins implying the development of multiple detachment systems organizing out-of-sequence, each new detachment fault developing into the previously exhumed basement. This spatial and temporal organization of fault systems leads to a final symmetry of exhumed domains at both conjugated margins. Magma appears to gradually increase during the margin development and is particularly present in the more distal domain where we can observe clear magma/fault interactions. We propose that the evolution of such rifted margins is linked to cycles of delocalisation/re-localisation of the deformation which could be mainly influenced by magma and by the decoupling between the upper brittle deformation and the asthenospheric uplift. In this context, the lithospheric breakup appears to be triggered by progressive syn-extensional thermal and magmatic weakening. However, the observation of continentward dipping reflectors interpreted as flip-flop detachment systems suggests that the localisation of the spreading centre and the onset of the steady state oceanic spreading will not be necessarily associated with a clear magmatic oceanic crust. In case of a low magmatic budget we can rather observe the onset of steady state amagmatic oceanic spreading, similar to what is expected at ultra-slow spreading ridges. This model of evolution (Gillard, 2014, PhD thesis) could well explain the fact that most magma-poor margins display symmetric exhumed domains on conjugate margins. However it raises the question of the nature of magnetic anomalies in ocean-continent transitions and their value for the interpretation of the kinematic evolution of conjugate rifted margins.

Robust Stability Analysis of the Space Launch System Control Design: A Singular Value Approach

NASA Technical Reports Server (NTRS)

Pei, Jing; Newsome, Jerry R.

2015-01-01

Classical stability analysis consists of breaking the feedback loops one at a time and determining separately how much gain or phase variations would destabilize the stable nominal feedback system. For typical launch vehicle control design, classical control techniques are generally employed. In addition to stability margins, frequency domain Monte Carlo methods are used to evaluate the robustness of the design. However, such techniques were developed for Single-Input-Single-Output (SISO) systems and do not take into consideration the off-diagonal terms in the transfer function matrix of Multi-Input-Multi-Output (MIMO) systems. Robust stability analysis techniques such as H(sub infinity) and mu are applicable to MIMO systems but have not been adopted as standard practices within the launch vehicle controls community. This paper took advantage of a simple singular-value-based MIMO stability margin evaluation method based on work done by Mukhopadhyay and Newsom and applied it to the SLS high-fidelity dynamics model. The method computes a simultaneous multi-loop gain and phase margin that could be related back to classical margins. The results presented in this paper suggest that for the SLS system, traditional SISO stability margins are similar to the MIMO margins. This additional level of verification provides confidence in the robustness of the control design.

A Very Stable High Throughput Taylor Cone-jet in Electrohydrodynamics

PubMed Central

Morad, M. R.; Rajabi, A.; Razavi, M.; Sereshkeh, S. R. Pejman

2016-01-01

A stable capillary liquid jet formed by an electric field is an important physical phenomenon for formation of controllable small droplets, power generation and chemical reactions, printing and patterning, and chemical-biological investigations. In electrohydrodynamics, the well-known Taylor cone-jet has a stability margin within a certain range of the liquid flow rate (Q) and the applied voltage (V). Here, we introduce a simple mechanism to greatly extend the Taylor cone-jet stability margin and produce a very high throughput. For an ethanol cone-jet emitting from a simple nozzle, the stability margin is obtained within 1 kV for low flow rates, decaying with flow rate up to 2 ml/h. By installing a hemispherical cap above the nozzle, we demonstrate that the stability margin could increase to 5 kV for low flow rates, decaying to zero for a maximum flow rate of 65 ml/h. The governing borders of stability margins are discussed and obtained for three other liquids: methanol, 1-propanol and 1-butanol. For a gravity-directed nozzle, the produced cone-jet is more stable against perturbations and the axis of the spray remains in the same direction through the whole stability margin, unlike the cone-jet of conventional simple nozzles. PMID:27917956

Dual-vergence structure from multiple migration of widely spaced OBSs

NASA Astrophysics Data System (ADS)

Yelisetti, Subbarao; Spence, George D.; Scherwath, Martin; Riedel, Michael; Klaeschen, Dirk

2017-10-01

The detailed structure of the northern Cascadia basin and frontal ridge region was obtained using data from several widely spaced ocean bottom seismometers (OBSs). Mirror imaging was used in which the downgoing multiples (mirror signal) are migrated as they provide information about a much larger area than imaging with primary signal alone. Specifically, Kirchhoff time migration was applied to hydrophone and vertical geophone data. Our results indicate remarkable structures that were not observed on the northern Cascadia margin in previous single-channel or multi-channel seismic (MCS) data. Results show that, in these water depths (2.0-2.5 km), an OBS can image up to 5 km on either side of its position on the seafloor and hence an OBS spacing of 5 km is sufficient to provide a two-fold migration stack. Results also show the top of the igneous oceanic crust at 5-6 km beneath the seafloor using only a small airgun source (120 in.3). Specifically, OBS migration results clearly show the continuity of reflectors which enabled the identification of frontal thrusts and a main thrust fault. These faults indicate, for the first time on this margin, the presence of a dual-vergence structure. These kinds of structures have so far been observed in < 0.5% of modern convergent margins and could be related to horizontal compression associated with subduction and low basal shear stress resulting from over-pressure. Reanalysis of previous MCS data from this region augmented the OBS migration results and further suggests that the vergence switches from seaward to landward around central Vancouver Island. Furthermore, fault geometry analyses indicate that the total amount of shortening accommodated due to faulting and folding is about 3 km, which suggest that thrusting would have started at least ∼ 65 ky ago.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Trevena, A.S.; Varga, R.J.; Collins, I.D.

Salin basin of central Myanmar is a tertiary fore-arc basin that extends over 10,000 mi{sup 2} and contains 30,000+ ft of siliciclastic rocks. In the western Salin basin, Tertiary deltaic and fluvial formations contain thousands of feet of lithic sandstones that alternate with transgressive shallow marine shales. Facies and paleocurrent studies indicate deposition by north-to-south prograding tidal deltas and associated fluvial systems in a semi-restricted basin. Presence of serpentinite and volcanic clasts in Tertiary sandstones may imply that the basin was bounded to the east by the volcanic arc and to the west by a fore-arc accretionary ridge throughout muchmore » of the Cenozoic. Salin basin is currently defined by a regional north/south-trending syncline with uplifts along the eastern and western margins. Elongate folds along the eastern basin margin verge to the east and lie above the reverse faults that dip west; much of Myanmar's present hydrocarbon production is from these structures. Analogous structures occur along the western margin, but verge to the west and are associated with numerous hydrocarbon seeps and hand-dug wells. These basin-bounding structures are the result of fault-propagation folding. In the western Salin basin, major detachments occur within the shaly Tabyin and Laungshe formations. Fault ramps propagated through steep forelimbs on the western sides of the folds, resulting in highly asymmetric footwall synclines. Stratigraphic and apatite fission track data are consistent with dominantly Plio-Pleistocene uplift, with limited uplift beginning approximately 10 Ma. Paleostress analysis of fault/slickenside data indicates that fold and thrust structures formed during regional east/west compression and are not related in any simple way to regional transpression as suggested by plate kinematics.« less

Late 20th Century Deep-seated Vertical Motions in New Orleans and implications for Gulf Coast Subsidence

NASA Astrophysics Data System (ADS)

Dokka, R. K.

2010-12-01

Subsidence of the Mississippi River delta and adjoining coastal areas is widely thought to be dominated by compaction of Holocene sediments. Current public policies regarding hurricane protection and ecosystems restoration are founded on this interpretation. To test this hypothesis, monuments that penetrate the entire Holocene section were measured using geodetic leveling and water gauges attached to bridge foundations. Results show that the entire sampling area subsided between 1955 and 1995 in amounts unanticipated by previous models. Subsidence due to processes originating below the Holocene section locally exceeded 0.9 m between 1955 and 1995. The maxima of deep subsidence occurred in the urbanized and industrialized sections of eastern New Orleans. Subsidence decreased away from urbanized areas and north of the belt of active basin margin normal faults; this decrease in subsidence continued to the north and east along the Mississippi coast. These independent measurements provide insights into the complexity and causes of modern landscape change in the region. Modern subsidence is clearly not dominated solely by shallow processes such as natural compaction, Deep subsidence occurring east and north of the basin margin faults can be explained by regional tectonic loading of the lithosphere by the modern Mississippi River delta and local groundwater withdrawal. Sharp, local changes in subsidence coincide with strands of the basin margin normal fault system. Deep subsidence of the New Orleans area can be explained by a combination of groundwater withdrawal from shallow upper Pleistocene aquifers, the aforementioned lithospheric loading, and non-groundwater-related faulting. Subsidence due to groundwater extraction from aquifers ~160 to 200 m deep dominated the urbanized areas from ~1960 to the early 1990s and is likely responsible for lowering flood protection structures and bridges in the area by as much as ~0.8 m.

Resolving the fine-scale velocity structure of continental hyperextension at the Deep Galicia Margin using full-waveform inversion

NASA Astrophysics Data System (ADS)

Davy, R. G.; Morgan, J. V.; Minshull, T. A.; Bayrakci, G.; Bull, J. M.; Klaeschen, D.; Reston, T. J.; Sawyer, D. S.; Lymer, G.; Cresswell, D.

2018-01-01

Continental hyperextension during magma-poor rifting at the Deep Galicia Margin is characterized by a complex pattern of faulting, thin continental fault blocks and the serpentinization, with local exhumation, of mantle peridotites along the S-reflector, interpreted as a detachment surface. In order to understand fully the evolution of these features, it is important to image seismically the structure and to model the velocity structure to the greatest resolution possible. Traveltime tomography models have revealed the long-wavelength velocity structure of this hyperextended domain, but are often insufficient to match accurately the short-wavelength structure observed in reflection seismic imaging. Here, we demonstrate the application of 2-D time-domain acoustic full-waveform inversion (FWI) to deep-water seismic data collected at the Deep Galicia Margin, in order to attain a high-resolution velocity model of continental hyperextension. We have used several quality assurance procedures to assess the velocity model, including comparison of the observed and modeled waveforms, checkerboard tests, testing of parameter and inversion strategy and comparison with the migrated reflection image. Our final model exhibits an increase in the resolution of subsurface velocities, with particular improvement observed in the westernmost continental fault blocks, with a clear rotation of the velocity field to match steeply dipping reflectors. Across the S-reflector, there is a sharpening in the velocity contrast, with lower velocities beneath S indicative of preferential mantle serpentinization. This study supports the hypothesis that normal faulting acts to hydrate the upper-mantle peridotite, observed as a systematic decrease in seismic velocities, consistent with increased serpentinization. Our results confirm the feasibility of applying the FWI method to sparse, deep-water crustal data sets.

Transfer zones and fault reactivation in inverted rift basins: Insights from physical modelling

NASA Astrophysics Data System (ADS)

Konstantinovskaya, Elena A.; Harris, Lyal B.; Poulin, Jimmy; Ivanov, Gennady M.

2007-08-01

Lateral transfer zones of deformation and fault reactivation were investigated in multilayered silicone-sand models during extension and subsequent co-axial shortening. Model materials were selected to meet similarity criteria and to be distinguished on CT scans; this approach permitted non-destructive visualisation of the progressive evolution of structures. Transfer zones were initiated by an orthogonal offset in the geometry of a basal mobile aluminium sheet and/or by variations of layer thickness or material rheology in basal layers. Transfer zones affected rift propagation and fault kinematics in models. Propagation and overlapping rift culminations occurred in transfer zones during extension. During shortening, deviation in the orientation of frontal thrusts and fold axes occurred within transfer zones in brittle and ductile layers, respectively. CT scans showed that steep (58-67°) rift-margin normal faults were reactivated as reverse faults. The reactivated faults rotated to shallower dips (19-38°) with continuing shortening after 100% inversion. Rotation of rift phase faults appears to be due to deep level folding and uplift during the inversion phase. New thrust faults with shallow dips (20-34°) formed outside the inverted graben at late stages of shortening. Frontal ramps propagated laterally past the transfer structure during shortening. During inversion, the layers filling the rift structures underwent lateral compression at the depth, the graben fill was pushed up and outwards creating local extension near the surface. Sand marker layers in inverted graben have showed fold-like structures or rotation and tilting in the rifts and on the rift margins. The results of our experiments conform well to natural examples of inverted graben. Inverted rift basins are structurally complex and often difficult to interpret in seismic data. The models may help to unravel the structure and evolution of these systems, leading to improved hydrocarbon exploration assessments. Model results may also be used to help predict the location of basement discontinuities which may have focused hydrothermal fluids during basin formation and inversion.

Syntectonic Deposition of Plio-Quaternary Sediments in the Santa Rosalia Basin of Baja California Sur, Mexico

NASA Astrophysics Data System (ADS)

Michels, A.; Johnson, L.; Niemi, T. M.

2017-12-01

Plio-Quaternary sediments of the Tirabuzón, Infierno, and Santa Rosalía formations record syntectonic deposition in the Santa Rosalía basin—an oblique-rift-margin basin along the Gulf of California in Baja California Sur, Mexico. These deposits unconformably overlie the upper Miocene, Cu-Zn-Co-Mn-rich Boleo Formation. The Mesa Soledad outcrops, exposed on the Minera Boleo mine property, show interfingering of marine and terrestrial deposits of the three formations along the inland margin of the basin in an area that has not previously been studied. Faults that cut the Pliocene section of the mesa are mostly steeply-dipping, NW- and NE-striking faults with normal displacement determined from stratigraphic offset and steep plunge in striations. Two stratigraphic sections were measured on either side of one of these high-angle, NW-striking fault that has a normal throw of 26 m. Our analyses of sediment grain size, fossil assemblages, and sedimentary petrography indicate a mismatch of the stratigraphic units across the fault and suggest a component of strike slip. North of the fault, poorly-sorted, well-rounded, fluvial gravels from the Pliocene-aged, Tirabuzón Formation unconformably underlie fossiliferous marine deposits from the late-Pliocene to Pleistocene? -aged Infierno Formation. South of the fault, marine deposits of the Tirabuzón Formation grade upward into imbricated, clast-supported beach gravel, and finally into non-marine conglomerates. The absence of the Infierno Formation on the southern side of the fault suggests the deposits were either eroded unevenly due to uplift or laterally displaced by strike-slip movement. Fossiliferous sandstones and conglomerates of the Santa Rosalía Formation unconformably cap the entire outcrop and show no displacement from faulting. The Santa Rosalía Formation is overlain by the 1.4 Ma La Reforma ignimbrite (Schmidt 2006), indicating that the style of deformation of the basin changed at approximately this time.

Deformation associated to exhumation by detachment faulting of upper mantle rocks in a fossil Ocean Continent Transition: The example of the Totalp unit in SE Switzerland

NASA Astrophysics Data System (ADS)

Picazo, S.; Manatschal, G.; Cannat, M.

2013-12-01

The exhumation of upper mantle rocks along detachment faults is widespread at Mid-Ocean Ridges and at the Ocean-Continent Transition (OCT) of rifted continental margins. Thermo-mechanical models indicate that significant strain softening of the fault rocks in the footwall is required in order to produce such large fault offsets. Our work focuses on deformation textures, and the associated mineralogy in ultramafic rocks sampled in the upper levels of the footwall next to the exhumation fault. We present two OCT examples, the Totalp relict of a paleo-Tethys OCT exposed in SE Switzerland, and the Iberian distal margin (ODP Leg 173 Site 1070). We built a new geological map and a section of the Totalp unit near Davos (SE Switzerland) and interpreted this area as a local exposure of a paleo-seafloor that is formed by an exhumed detachment surface and serpentinized peridotites. The top of the exhumed mantle rocks is made of ophicalcites that resulted from the carbonation of serpentine under static conditions at the seafloor. The ophicalcites preserve depositional contacts with Upper Jurassic to Lower Cretaceous pelagic sediments. These sequences did not exceed prehnite-pumpellyite metamorphic facies conditions, and locally escaped Alpine deformation. Thin mylonitic shear zones as well as foliated amphibole-bearing ultramafic rocks have been mapped. The age of these rocks and the link with the final exhumation history are yet unknown but since amphibole-bearing ultramafic rocks can be found as clasts in cataclasites related to the detachment fault, they pre-date detachment faulting. Our petrostructural study of the exhumed serpentinized rocks also reveals a deformation gradient from cataclasis to gouge formation within 150m in the footwall of the proposed paleo-detachment fault. This deformation postdates serpentinization. It involves a component of plastic deformation of serpentine in the most highly strained intervals that has suffered pronounced grain-size reduction and a polyphase cataclastic overprint.

Mass-transport deposits controlling fault propagation, reactivation and structural decoupling on continental margins (Espírito Santo Basin, SE Brazil)

NASA Astrophysics Data System (ADS)

Omosanya, Kamal'deen O.; Alves, Tiago M.

2014-07-01

This work uses high-quality 3D seismic data to assess the importance of mass-transport deposits (MTDs) as markers of fault propagation. We mapped three distinct MTDs and several fault families on the continental slope of Espírito Santo, SE Brazil. Fault mapping was based on seismic attributes such as seismic coherence and structural smoothing, and was further completed using ant tracking algorithms. Genetically related fault families were analysed in terms of their throw-depth (t-z) and throw-distance (t-x) gradient curves. A key result in this paper is that vertical fault propagation can be hindered by MTDs, as demonstrated for Eocene to Early Miocene faults in parts of the study area. Throw-depth variations in faults affected by MTDs are associated with: a) lithologic controls resulting from the presence of MTDs, b) local fault segmentation and c) reactivation by dip linkage. Based on their orientation and degree of interaction with MTDs, interpreted faults can be classified as decoupled and non-decoupled. Importantly, faults decoupled by MTDs have quasi-elliptical t-x profiles and show smaller cumulative throw values and fault propagation rates when compared to their non-decoupled counterparts. Recurrent MTDs can therefore be used as markers to estimate structural decoupling between distinct fault families.

The structures, stratigraphy and evolution of the Gulf of Corinth rift, Greece

NASA Astrophysics Data System (ADS)

Taylor, Brian; Weiss, Jonathan R.; Goodliffe, Andrew M.; Sachpazi, Maria; Laigle, Mireille; Hirn, Alfred

2011-06-01

A multichannel seismic and bathymetry survey of the central and eastern Gulf of Corinth (GoC), Greece, reveals the offshore fault geometry, seismic stratigraphy and basin evolution of one of Earths most active continental rift systems. Active, right-stepping, en-echelon, north-dipping border faults trend ESE along the southern Gulf margin, significantly overlapping along strike. The basement offsets of three (Akrata-Derveni, Sithas and Xylocastro) are linked. The faults are biplanar to listric: typically intermediate angle (˜35° in the centre and 45-48° in the east) near the surface but decreasing in dip and/or intersecting a low- or shallow-angle (15-20° in the centre and 19-30° in the east) curvi-planar reflector in the basement. Major S-dipping border faults were active along the northern margin of the central Gulf early in the rift history, and remain active in the western Gulf and in the subsidiary Gulf of Lechaio, but unlike the southern border faults, are without major footwall uplift. Much of the eastern rift has a classic half-graben architecture whereas the central rift has a more symmetric w- or u-shape. The narrower and shallower western Gulf that transects the >40-km-thick crust of the Hellenides is associated with a wider distribution of overlapping high-angle normal faults that were formerly active on the Peloponnesus Peninsula. The easternmost sector includes the subsidiary Gulfs of Lechaio and Alkyonides, with major faults and basement structures trending NE, E-W and NW. The basement faults that control the rift architecture formed early in the rift history, with little evidence (other than the Vrachonisida fault along the northern margin) in the marine data for plan view evolution by subsequent fault linkage. Several have maximum offsets near one end. Crestal collapse graben formed where the hanging wall has pulled off the steeper onto the shallower downdip segment of the Derveni Fault. The dominant strikes of the Corinth rift faults gradually rotate from 090-120° in the basement and early rift to 090-100° in the latest rift, reflecting a ˜10° rotation of the opening direction to the 005° presently measured by GPS. The sediments include a (locally >1.5-km-) thick, early-rift section, and a late-rift section (also locally >1.5-km-thick) that we subdivide into three sequences and correlate with seven 100-ka glacio-eustatic cycles. The Gulf depocentre has deepened through time (currently >700 mbsl) as subsidence has outpaced sedimentation. We measure the minimum total horizontal extension across the central and eastern Gulf as varying along strike between 4 and 10 km, and estimate full values of 6-11 km. The rift evolution is strongly influenced by the inherited basement fabric. The regional NNW structural fabric of the Hellenic nappes changes orientation to ESE in the Parnassos terrane, facilitating the focused north-south extension observed offshore there. The basement-penetrating faults lose seismic reflectivity above the 4-14-km-deep seismogenic zone. Multiple generations and dips of normal faults, some cross-cutting, accommodate extension beneath the GoC, including low-angle (15-20°) interfaces in the basement nappes. The thermally cool forearc setting and cross-orogen structures unaccompanied by magmatism make this rift a poor analogue and unlikely precursor for metamorphic core complex formation.

Slow Slip Predictions Based on Gabbro Dehydration and Friction Data Compared to GPS Measurements in Northern Cascadia

NASA Astrophysics Data System (ADS)

Rice, J. R.; Liu, Y.

2008-12-01

For episodic slow slip transients in subduction zones, a large uncertainty in comparing surface deformations predicted by rate and state friction modeling [Liu and Rice, JGR, 2007] to GPS measurements lies in our limited knowledge of the frictional properties and fluid pore pressure along the fault. In this study, we apply petrological data [Peacock et al., USGS, 2002; Hacker et al., JGR 2003; Wada et al., JGR, 2008] and recently reported friction data [He et al., Tectonophys, 2006, 2007] for gabbro, as a reasonable representation of the seafloor, to a Cascadia-like 2D model in order to produce simulations which show spontaneous aseismic transients. We compare the resulting inter-transient and transient surface deformations to GPS observations along the northern Cascadia margin. An inferred region along dip of elevated fluid pressure is constrained by seismological observations where available, and by thermal and petrological models for the Cascadia and SW Japan subduction zones. For the assumed a and a-b profiles, we search the model parameter space, by varying the level of effective normal stress σ, characteristic slip distance L in the source areas of transients, and the fault width under that low σ, to identify simulation cases which produce transient aseismic slip and recurrence interval similar to the observed 20-30 mm and 14 months, respectively, in northern Cascadia. Using a simple planar fault geometry and extrapolating the 2D fault slip to a 3D distribution, we find that the gabbro gouge friction data allows a much better fit to GPS observations than is possible with the granite data [Blanpied et al., JGR, 1995, 1998] which, for lack of a suitable alternative, has been used as the basis for most previous subduction earthquake modeling, including ours. Nevertheless, the values of L required to reasonably fit the geodetic data during a transient event are somewhat larger than 100 microns, rather than in the range of 10 to a few 10s of microns as might be expected from lab results. We propose elsewhere at this meeting [Liu et al., submitted abstract] that dilatancy of fault gouge, and related frictional stabilization because of its assumed infiltration by dehydration fluids, may be important to resolving that discrepancy. Those dilatancy effects are known from Segall and Rice [JGR, 1995] to be important in stabilizing otherwise unstable friction at conditions of low σ like those assumed, and they have been shown by Segall and Rubin [EOS, 2007] to be capable of producing episodic slow slip transients.

Modification of wave-cut and faulting-controlled landforms.

USGS Publications Warehouse

Hanks, T.C.; Bucknam, R.C.; Lajoie, K.R.; Wallace, R.E.

1984-01-01

From a casual observation that the form of degraded fault scarps resembles the error function, this investigation proceeds through an elementary diffusion equation representation of landform evolution to the application of the resulting equations to the modern topography of scarplike landforms. The value of K = 1 GKG (K = 'mass diffusivity'; 1 GKG = 1m2/ka) may be generally applicable as a good first approximation, to the modification of alluvial terranes within the semiarid regions of the western United States. The Lake Bonneville shoreline K is the basis for dating four sets of fault scarps in west-central Utah. The Drum Mountains fault scarps date at 3.6 to 5.7 ka BP. Fault scarps along the eastern base of the Fish Springs Range are very young, 3 ka BP. We estimate the age of fault scarps along the western flank of the Oquirrh Mountains to be 32 ka B.P. Fault scarps along the NE margin of the Sheeprock Mountains are even older, 53 ka BP. -from Authors

Geomorphology and Neogene tectonic evolution of the Palomares continental margin (Western Mediterranean)

NASA Astrophysics Data System (ADS)

Gómez de la Peña, Laura; Gràcia, Eulàlia; Muñoz, Araceli; Acosta, Juan; Gómez-Ballesteros, María; R. Ranero, César; Uchupi, Elazar

2016-10-01

The Palomares continental margin is located in the southeastern part of Spain. The margin main structure was formed during Miocene times, and it is currently part of the wide deformation zone characterizing the region between the Iberian and African plates, where no well-defined plate boundary occurs. The convergence between these two plates is here accommodated by several structures, including the left lateral strike-slip Palomares Fault. The region is characterized by sparse, low to moderate magnitude (Mw < 5.2) shallow instrumental earthquakes, although large historical events have also occurred. To understand the recent tectonic history of the margin we analyze new high-resolution multibeam bathymetry data and re-processed three multichannel seismic reflection profiles crossing the main structures. The analysis of seafloor morphology and associated subsurface structure provides new insights of the active tectonic features of the area. In contrast to other segments of the southeastern Iberian margin, the Palomares margin contains numerous large and comparatively closely spaced canyons with heads that reach near the coast. The margin relief is also characterized by the presence of three prominent igneous submarine ridges that include the Aguilas, Abubacer and Maimonides highs. Erosive processes evidenced by a number of scars, slope failures, gullies and canyon incisions shape the present-day relief of the Palomares margin. Seismic images reveal the deep structure distinguishing between Miocene structures related to the formation of the margin and currently active features, some of which may reactivate inherited structures. The structure of the margin started with an extensional phase accompanied by volcanic accretion during the Serravallian, followed by a compressional pulse that started during the Latemost Tortonian. Nowadays, tectonic activity offshore is subdued and limited to few, minor faults, in comparison with the activity recorded onshore. The deep Algero-Balearic Basin is affected by surficial processes, associated to halokinesis of Messinian evaporites.

Sacra Fossae

NASA Image and Video Library

2018-04-19

Located on the western margin of Lunae Planum, Sacra Fossae is a group of linear depressions. The right angle turns and uniform width seen in this VIS image indicate that these channels were formed by faulting rather than liquid flow. Two bounding faults with a down-dropped interior are called graben. Orbit Number: 71244 Latitude: 17.7623 Longitude: 288.309 Instrument: VIS Captured: 2018-01-05 09:06 https://photojournal.jpl.nasa.gov/catalog/PIA22373

Crustal Seismicity and Geomorphic Observations of the Chiripa-Haciendas Fault System: The Guanacaste Volcanic Arc Sliver of Western Costa Rica

NASA Astrophysics Data System (ADS)

Lewis, J. C.; Montero Pohly, W. K.; Araya, M. C.

2017-12-01

It has recently been shown that contemporary northwest motion of the Nicoya Peninsula of Costa Rica reflects a tectonic sliver that includes much of the upper-plate arc, referred to as the Guanacaste Volcanic Arc Sliver (GVAS). Here we characterize historical seismicity and geomorphic expressions of faults that define the northeastern margin of the GVAS. Several crustal earthquakes and their aftershocks provide constraints on the geometry and/or kinematics of the fault system. These include the Armenia earthquake of July 12, 2011, the Bijagua earthquake of January 27, 2002, the Tilarán earthquake of April 13, 1973 and two much older events. We summarize these earthquakes in the context of recent fault mapping and focal mechanism solutions, and suggest that most of the deformation can be explained by slip on steeply dipping NW-striking fault planes accommodating dextral slip. Streams that cross the major fault traces we have mapped also show deflections consistent with dextral slip. These include map-view apparent offsets of 6.5 km for the Haciendas River, 1.0 km for the Orosi River and 0.6 km for the Pizote River. Although preservation is poor, we document stream terrace risers that reveal truncations and/or offsets consistent with dextral slip. Additional constraints on the fault system are apparent as it is traced into Lake Nicaragua. Previous workers have shown that earthquake clusters accommodate a combination of dextral slip on NW-strike faults and sinistral slip NE-strike faults, the latter described as part of a system of bookshelf fault blocks. Whether the northeastern margin of the GVAS under Lake Nicaragua is a single fault strand or an array of bookshelf blocks remains an open question. An equally important gap in our understanding is the kinematic link of the fault system to the east where the GVAS originates. Our results set the stage for expanded studies that will be essential to understanding the relative contributions of Cocos Ridge collision and coupling between the North American plate and the Caribbean Plate in driving the sliver motion. They are also important in the context of natural hazards, both seismic ground accelerations and mass-wasting. This was made clear by the 1973 Tilarán earthquake, which included fatalities, and several damaging moderate-magnitude crustal earthquakes on 3 July 2016.

Crustal structure across the Altyn Tagh Range at the northern margin of the Tibetan Plateau and tectonic implications

USGS Publications Warehouse

Zhao, J.; Mooney, W.D.; Zhang, X.; Li, Z.; Jin, Z.; Okaya, N.

2006-01-01

We present new seismic refraction/wide-angle-reflection data across the Altyn Tagh Range and its adjacent basins. We find that the crustal velocity structure, and by inference, the composition of the crust changes abruptly beneath the Cherchen fault, i.e., ???100 km north of the northern margin of the Tibetan plateau. North of the Cherchen fault, beneath the Tarim basin, a platform-type crust is evident. In contrast, south the Cherchen fault the crust is characterized by a missing high-velocity lower-crustal layer. Our seismic model indicates that the high topography (???3 km) of the Altyn Tagh Range is supported by a wedge-shaped region with a seismic velocity of 7.6-7.8 km/s that we interpret as a zone of crust-mantle mix. We infer that the Altyn Tagh Range formed by crustal-scale strike-slip motion along the North Altyn Tagh fault and northeast-southwest contraction over the range. The contraction is accommodated by (1) crustal thickening via upper-crustal thrusting and lower-crustal flow (i.e., creep), and (2) slip-parallel (SW-directed) underthrusting of only the lower crust and mantle of the eastern Tarim basin beneath the Altyn Tagh Range. ?? 2005 Elsevier B.V. All rights reserved.

Summary of the stratigraphy and structural elements related to plate convergence of the Quetta-Muslim Bagh-Sibi region, Balochistan, west-central Pakistan

USGS Publications Warehouse

Maldonado, Florian; Mengal, Jan M.; Khan, Shahid H.; Warwick, Peter D.

2011-01-01

The four major faults that bound the structural terrane are the Frontal (F), Ghazaband-Zhob (GZ), Gwal-Bagh (GB), and Chaman (C) faults. Four major periods of deformation are recognized: (1) emplacement of ophiolitic rocks onto the continental margin of the India plate; (2) convergence of the India-Eurasia plates; (3) deposition of Tertiary-Quaternary molasse units followed by major folding and thrusting, and formation of strike-slip faults; and (4) deposition of Pleistocene molasse units with subsequent folding, thrusting, and strike-slip motion that continues to the present.

Method and apparatus for transfer function simulator for testing complex systems

NASA Technical Reports Server (NTRS)

Kavaya, M. J. (Inventor)

1985-01-01

A method and apparatus for testing the operation of a complex stabilization circuit in a closed loop system is presented. The method is comprised of a programmed analog or digital computing system for implementing the transfer function of a load thereby providing a predictable load. The digital computing system employs a table stored in a microprocessor in which precomputed values of the load transfer function are stored for values of input signal from the stabilization circuit over the range of interest. This technique may be used not only for isolating faults in the stabilization circuit, but also for analyzing a fault in a faulty load by so varying parameters of the computing system as to simulate operation of the actual load with the fault.

Young rift kinematics in the Tadjoura rift, western Gulf of Aden, Republic of Djibouti

NASA Astrophysics Data System (ADS)

Daoud, Mohamed A.; Le Gall, Bernard; Maury, René C.; Rolet, JoëL.; Huchon, Philippe; Guillou, Hervé

2011-02-01

The Tadjoura rift forms the westernmost edge of the westerly propagating Sheba ridge, between Arabia and Somalia, as it enters into the Afar depression. From structural and remote sensing data sets, the Tadjoura rift is interpreted as an asymmetrical south facing half-graben, about 40 km wide, dominated by a large boundary fault zone to the north. It is partially filled up by the 1-3 Myr old Gulf Basalts which onlapped the older Somali Basalts along its shallower southern flexural margin. The major and trace element analysis of 78 young onshore lavas allows us to distinguish and map four distinct basaltic types, namely the Gulf, Somali, Goumarre, and Hayyabley Basalts. These results, together with radiometric age data, lead us to propose a revised volcano-stratigraphic sketch of the two exposed Tadjoura rift margins and to discriminate and date several distinct fault networks of this oblique rift. Morphological and statistical analyses of onshore extensional fault populations show marked changes in structural styles along-strike, in a direction parallel to the rift axis. These major fault disturbances are assigned to the arrest of axial fault tip propagation against preexisting discontinuities in the NS-oriented Arta transverse zone. According to our model, the sinistral jump of rifting into the Asal-Ghoubbet rift segment results from structural inheritance, in contrast with the en échelon or transform mechanism of propagation that prevailed along the entire length of the Gulf of Aden extensional system.

An Analytical Model for Assessing Stability of Pre-Existing Faults in Caprock Caused by Fluid Injection and Extraction in a Reservoir

NASA Astrophysics Data System (ADS)

Wang, Lei; Bai, Bing; Li, Xiaochun; Liu, Mingze; Wu, Haiqing; Hu, Shaobin

2016-07-01

Induced seismicity and fault reactivation associated with fluid injection and depletion were reported in hydrocarbon, geothermal, and waste fluid injection fields worldwide. Here, we establish an analytical model to assess fault reactivation surrounding a reservoir during fluid injection and extraction that considers the stress concentrations at the fault tips and the effects of fault length. In this model, induced stress analysis in a full-space under the plane strain condition is implemented based on Eshelby's theory of inclusions in terms of a homogeneous, isotropic, and poroelastic medium. The stress intensity factor concept in linear elastic fracture mechanics is adopted as an instability criterion for pre-existing faults in surrounding rocks. To characterize the fault reactivation caused by fluid injection and extraction, we define a new index, the "fault reactivation factor" η, which can be interpreted as an index of fault stability in response to fluid pressure changes per unit within a reservoir resulting from injection or extraction. The critical fluid pressure change within a reservoir is also determined by the superposition principle using the in situ stress surrounding a fault. Our parameter sensitivity analyses show that the fault reactivation tendency is strongly sensitive to fault location, fault length, fault dip angle, and Poisson's ratio of the surrounding rock. Our case study demonstrates that the proposed model focuses on the mechanical behavior of the whole fault, unlike the conventional methodologies. The proposed method can be applied to engineering cases related to injection and depletion within a reservoir owing to its efficient computational codes implementation.

Marginal inherited structures impact on the oblique convergent N American Plate/ Central Caribbean plate-boundary in the Northern Caribbean. The tectonic evolution since Miocene times based on Haiti data acquired onshore and offshore since 2012- a step toward an ADP Drilling Proposal (Haiti-DRILL).

NASA Astrophysics Data System (ADS)

Ellouz, N.; Hamon, Y.; Deschamps, R.; Battani, A.; Wessels, R.; Boisson, D.; Prepetit, C.; Momplaisir, R.

2017-12-01

Since Early Paleogene times, the North Caribbean plate is colliding obliquely with the south continental part of the old N. American Margins, which is represented by various segments from West to East, inherited from Jurassic times. Location, amount of displacement, rotation and the structural deformation of these margin segments, resulting from the dislocation of the continental N American margin, are not clearly yet established. At present, the plate limits are marked either by two left lateral faults west and inside Haiti (OSF in the North and EPGF in the South), oblique collision front (further west in Cuba), oblique subducted segments (to the East, Porto-Rico). From our recent works operated both offshore (Haiti-SIS and Haiti-BGF surveys 2012-2015) and onshore (field campaigns 2013-2017) in Haitian zone, the position of the present-day and paleo major limits have been redefined. These paleolimits have been reconstructed up to early Miocene times, based on: restoration of regional structural cross-sections, sedimentology and on paleoenvironement studies. In a preliminary way, we analyzed the complexity of the tectonic heritage with possible nature, heterogeneity of the crustal fragments and associated margins close to Haiti (age, structure, environment, location of the dislocated blocks through times) which profoundly impact the partitioning of the deformation along this complex transformed margin. The change in the structure wavelength, decollement level variations are primary constraints in the restoration of the main units and do impose a deep connection along specific segments either related to strike-slip or to splay faults. The asymmetry on the repartition of the fault activity tend to prove that the past motion related to "EPGF transfer zone" is mainly partitioned in Haiti to the North of the present-day EPGF position. At present, these results are still coherent with the distribution of the aftershoks registered after 2010, and with the present-day seismicity during the last years.

Final Scientific/Technical Report: Characterizing the Response of the Cascadia Margin Gas Hydrate Reservoir to Bottom Water Warming Along the Upper Continental Slope

DOE Office of Scientific and Technical Information (OSTI.GOV)

Solomon, Evan A.; Johnson, H. Paul; Salmi, Marie

The objective of this project is to understand the response of the WA margin gas hydrate system to contemporary warming of bottom water along the upper continental slope. Through pre-cruise analysis and modeling of archive and recent geophysical and oceanographic data, we (1) inventoried bottom simulating reflectors along the WA margin and defined the upper limit of gas hydrate stability, (2) refined margin-wide estimates of heat flow and geothermal gradients, (3) characterized decadal scale temporal variations of bottom water temperatures at the upper continental slope of the Washington margin, and (4) used numerical simulations to provide quantitative estimates of howmore » the shallow boundary of methane hydrate stability responds to modern environmental change. These pre-cruise results provided the context for a systematic geophysical and geochemical survey of methane seepage along the upper continental slope from 48° to 46°N during a 10-day field program on the R/V Thompson from October 10-19, 2014. This systematic inventory of methane emissions along this climate-sensitive margin corridor and comprehensive sediment and water column sampling program provided data and samples for Phase 3 of this project that focused on determining fluid and methane sources (deep-source vs. shallow; microbial, thermogenic, gas hydrate dissociation) within the sediment, and how they relate to contemporary intermediate water warming. During the 2014 research expedition, we sampled nine seep sites between ~470 and 520 m water depth, within the zone of predicted methane hydrate retreat over the past 40 years. We imaged 22 bubble plumes with heights commonly rising to ~300 meters below sea level with one reaching near the sea surface. We collected 22 gravity cores and 20 CTD/hydrocasts from the 9 seeps and at background locations (no acoustic evidence of seepage) within the depth interval of predicted downslope retreat of the methane hydrate stability zone. Approximately 300 pore water samples were extracted from the gravity cores, and the pore water was analyzed for a comprehensive suite of solutes, gases, and stable isotope ratios. This comprehensive geochemical dataset was used to characterize the fluid and gas source(s) at each of the seep sites surveyed. The primary results of this project are: 1) Bottom simulating reflector-derived heat flow values decrease from 95 mW/m2 10 km east of the deformation front to ~60 mW/m2 60 km landward of the deformation front, with anomalously low values of ~25 mW/m2 on a prominent mid-margin terrace off central Washington. 2) The temperature of the incoming sediment/ocean crust interface at the deformation front ranges between 164-179 oC off central Washington, and the 350 oC isotherm at the top of the subducting ocean crust occurs 95 km landward of the deformation front. Differences between BSR-derived heat flow and modeled conductive heat flow suggest mean upward fluid flow rates of 0.4 cm/yr across the margin, with local regions (e.g. fault zones) exhibiting fluid flow rates up to 3.5 cm/yr. 3) A compilation of 2122 high-resolution CTD, glider, and Argo float temperature profiles spanning the upper continental slope of the Washington margin from the years 1968 to 2013 show a long-term warming trend that ranges from 0.006-0.008 oC/yr. Based on this long-term bottom water warming, we developed a 2-D thermal model to simulate the change in sediment temperature distribution over this period, along with the downslope retreat of the methane hydrate stability field. Over the 43 years of the simulation, the thermal disturbance propagated 30 m into the sediment column, causing the base of the methane hydrate stability field to shoal ~13 m and to move ~1 km downslope. 4) A preliminary analysis of seafloor observations and mid-water column acoustic data to detect bubble plumes was used to characterize the depth distribution of seeps along the Cascadia margin. These results indicate high bubble plume densities along the continental shelf at water depths <180 m and at the upper limit of methane hydrate stability along the Washington margin. 5) The majority of the seeps cored during the 2014 research expedition on the R/V Thompson contained abundant authigenic carbonate indicating that they are locations of long-lived seepage rather than emergent seep systems related to methane hydrate dissociation. Despite the evidence for enhanced methane seepage at the upper limit of methane hydrate stability along the Washington margin, we found no unequivocal evidence for active methane hydrate dissociation as a source of fluid and gas at the seeps surveyed. The pore fluid and bottom water chemistry shows that the seeps are fed by a variety of fluid and methane sources, but that methane hydrate dissociation, if occurring, is not widespread and is only a minor source (below the detection limit of our methods). Collectively, these results provide a significant advance in our understanding of the thermal structure of the Cascadia subduction zone and the fluid and methane sources feeding seeps along the upper continental slope of the Washington-sector of the Cascadia margin. Though we did not find unequivocal evidence for methane hydrate dissociation as a source of water and methane at the upper pressure-temperature limit of methane hydrate stability at present, continued warming of North Pacific Intermediate Water in the future has the potential to impact the methane hydrate reservoir in sediments at greater depths along the slope. Thus, this study provides a strong foundation and the necessary characterization of the background state of seepage at the upper limit of methane hydrate stability for future investigations of this important process.« less

Nonlinear dynamics near the stability margin in rotating pipe flow

NASA Technical Reports Server (NTRS)

Yang, Z.; Leibovich, S.

1991-01-01

The nonlinear evolution of marginally unstable wave packets in rotating pipe flow is studied. These flows depend on two control parameters, which may be taken to be the axial Reynolds number R and a Rossby number, q. Marginal stability is realized on a curve in the (R, q)-plane, and the entire marginal stability boundary is explored. As the flow passes through any point on the marginal stability curve, it undergoes a supercritical Hopf bifurcation and the steady base flow is replaced by a traveling wave. The envelope of the wave system is governed by a complex Ginzburg-Landau equation. The Ginzburg-Landau equation admits Stokes waves, which correspond to standing modulations of the linear traveling wavetrain, as well as traveling wave modulations of the linear wavetrain. Bands of wavenumbers are identified in which the nonlinear modulated waves are subject to a sideband instability.

Bounded Linear Stability Analysis - A Time Delay Margin Estimation Approach for Adaptive Control

NASA Technical Reports Server (NTRS)

Nguyen, Nhan T.; Ishihara, Abraham K.; Krishnakumar, Kalmanje Srinlvas; Bakhtiari-Nejad, Maryam

2009-01-01

This paper presents a method for estimating time delay margin for model-reference adaptive control of systems with almost linear structured uncertainty. The bounded linear stability analysis method seeks to represent the conventional model-reference adaptive law by a locally bounded linear approximation within a small time window using the comparison lemma. The locally bounded linear approximation of the combined adaptive system is cast in a form of an input-time-delay differential equation over a small time window. The time delay margin of this system represents a local stability measure and is computed analytically by a matrix measure method, which provides a simple analytical technique for estimating an upper bound of time delay margin. Based on simulation results for a scalar model-reference adaptive control system, both the bounded linear stability method and the matrix measure method are seen to provide a reasonably accurate and yet not too conservative time delay margin estimation.

Structural styles of Paleozoic intracratonic fault reactivation: A case study of the Grays Point fault zone in southeastern Missouri, USA

USGS Publications Warehouse

Clendenin, C.W.; Diehl, S.F.

1999-01-01

A pronounced, subparallel set of northeast-striking faults occurs in southeastern Missouri, but little is known about these faults because of poor exposure. The Commerce fault system is the southernmost exposed fault system in this set and has an ancestry related to Reelfoot rift extension. Recent published work indicates that this fault system has a long history of reactivation. The northeast-striking Grays Point fault zone is a segment of the Commerce fault system and is well exposed along the southeast rim of an inactive quarry. Our mapping shows that the Grays Point fault zone also has a complex history of polyphase reactivation, involving three periods of Paleozoic reactivation that occurred in Late Ordovician, Devonian, and post-Mississippian. Each period is characterized by divergent, right-lateral oblique-slip faulting. Petrographic examination of sidwall rip-out clasts in calcite-filled faults associated with the Grays Point fault zone supports a minimum of three periods of right-lateral oblique-slip. The reported observations imply that a genetic link exists between intracratonic fault reactivation and strain produced by Paleozoic orogenies affecting the eastern margin of Laurentia (North America). Interpretation of this link indicate that right-lateral oblique-slip has occurred on all of the northeast-striking faults in southeastern Missouri as a result of strain influenced by the convergence directions of the different Paleozoic orogenies.

Analysis of a Complex Faulted CO 2 Reservoir Using a Three-dimensional Hydro-geochemical-Mechanical Approach

DOE PAGES

Nguyen, Ba Nghiep; Hou, Zhangshuan; Bacon, Diana H.; ...

2017-08-18

This work applies a three-dimensional (3D) multiscale approach recently developed to analyze a complex CO 2 faulted reservoir that includes some key geological features of the San Andreas and nearby faults. The approach couples the STOMP-CO2-R code for flow and reactive transport modeling to the ABAQUS ® finite element package for geomechanical analysis. The objective is to examine the coupled hydro-geochemical-mechanical impact on the risk of hydraulic fracture and fault slip in a complex and representative CO 2 reservoir that contains two nearly parallel faults. STOMP-CO2-R/ABAQUS ® coupled analyses of this reservoir are performed assuming extensional and compressional stress regimesmore » to predict evolutions of fluid pressure, stress and strain distributions as well as potential fault failure and leakage of CO 2 along the fault damage zones. The tendency for the faults to slip and pressure margin to fracture are examined in terms of stress regime, mineral composition, crack distributions in the fault damage zones and geomechanical properties. Here, this model in combination with a detailed description of the faults helps assess the coupled hydro-geochemical-mechanical effect.« less

New insight into the 1556 M8 Huaxian earthquake in China

NASA Astrophysics Data System (ADS)

Ma, J.

2017-12-01

The disastrous 1556 M8 Huaxian earthquake in China took away 0.8Ma lives then as well as attracted scientists' attention. Although the Huashan front fault and Weinan plateform-front fault at the south margin of Weihe basin was responsible for this earthquake, we know less about the fault behaviors. There's evidence that the modern riverbank offset and older geomorphic scarps in Chishui river site on Weinan plateau-front fault from the Pleiades DEM. Here, we did a 3D trench excavation model using SfM work, drilling profiles and geomorphological measurement there to revive the site for multiearthquakes. It turns out two events occurred on the normal fault with pretty high offsets 9.4m and 7.8-8.0m respectively, the later one resulted from Huaxian earthquake. And we estimate that the fault slip rate approximately 1.48-1.75 mm/a. Thus, we find that the older earthquake also produced a similar fault offsets to the 1556 earthquake showing as characteristics earthquake. The paleoseismic study demonstrates that the Weinan pateform-front fault plays a role in boundary faults of Weihe basin, which can contribute to the basin evolution of regions of active faulting.

Analysis of a Complex Faulted CO 2 Reservoir Using a Three-dimensional Hydro-geochemical-Mechanical Approach

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nguyen, Ba Nghiep; Hou, Zhangshuan; Bacon, Diana H.

This work applies a three-dimensional (3D) multiscale approach recently developed to analyze a complex CO 2 faulted reservoir that includes some key geological features of the San Andreas and nearby faults. The approach couples the STOMP-CO2-R code for flow and reactive transport modeling to the ABAQUS ® finite element package for geomechanical analysis. The objective is to examine the coupled hydro-geochemical-mechanical impact on the risk of hydraulic fracture and fault slip in a complex and representative CO 2 reservoir that contains two nearly parallel faults. STOMP-CO2-R/ABAQUS ® coupled analyses of this reservoir are performed assuming extensional and compressional stress regimesmore » to predict evolutions of fluid pressure, stress and strain distributions as well as potential fault failure and leakage of CO 2 along the fault damage zones. The tendency for the faults to slip and pressure margin to fracture are examined in terms of stress regime, mineral composition, crack distributions in the fault damage zones and geomechanical properties. Here, this model in combination with a detailed description of the faults helps assess the coupled hydro-geochemical-mechanical effect.« less

Automated design and optimization of flexible booster autopilots via linear programming. Volume 2: User's manual

NASA Technical Reports Server (NTRS)

Hauser, F. D.; Szollosi, G. D.; Lakin, W. S.

1972-01-01

COEBRA, the Computerized Optimization of Elastic Booster Autopilots, is an autopilot design program. The bulk of the design criteria is presented in the form of minimum allowed gain/phase stability margins. COEBRA has two optimization phases: (1) a phase to maximize stability margins; and (2) a phase to optimize structural bending moment load relief capability in the presence of minimum requirements on gain/phase stability margins.

Pliocene to Recent Tectonic Activity of the Reşadiye Peninsula and the Relationship Between the Recent Earthquakes Occurred in the Gulf of Gökova: Preliminary Results.

NASA Astrophysics Data System (ADS)

Kahraman, Burcu; Özsayın, Erman; Üner, Serkan; Dirik, Kadir

2013-04-01

The E-W trending Reşadiye peninsula located at the southwestern part of the Anatolian Plate is an important horst developed between Gökova and Hisarönü Grabens. NW-trending the Datça Graben is the prominent structure comprising on the Reşadiye peninsula and records the significant fingerprints of palaeogeographical and kinematical characteristics from Pliocene to recent. The Datça Graben is controlled by NW-trending the Karaköy fault in the south and E-W trending the Kızlan fault in the north. Basement rocks of the graben are composed of ophiolitic rocks of the Lycian Nappes and Jurassic marine carbonates. The basinfill initiates with Early Pliocene Kızılaǧaç formation consisting conglomerates and continues with transgressive sequence (Yıldırımlı formation) composed of conglomerates, sandstones and marls with ignimbrite intercalations. Late Pliocene age was attributed to this formation based on the gastropoda and pelecypoda fauna according to previous studies. These units are unconformably overlain by Quaternary Karaköy formation consisting red blocky conglomerates. Pyroclastics of Quaternary age (161 ka) cover the older units. Alluvium, alluvial fan deposits and terrace deposits are the youngest units of the study area. To state the tectonic evolution of the Datça Graben, bedding planes and palaeostress analysis of the fault-slip data were used. The palaeostress analyses of the Kızlan fault clearly represent N-S tensional stress regime with pure normal fault characteristics. Due to the thick colluvium and alluvial fans, any fault-slip data were collected from the Karaköy fault. Considering the same stress regime is viable for the southwestern margin of the graben, fault planes ought to have normal fault characteristics with minor strike-slip component. SW-dipping bedding planes and SW-bearing palaeocurrent measurements show that Karaköy fault occurred before the Kızlan fault and the basin was first formed as a half-graben during Early Pliocene and continued till Late Pliocene. As the Kızlan fault juxtaposes the Kızılaǧaç and Yıldırımlı formations, Late Pliocene age is attributed to the fault. Focal mechanism solutions of recent earthquakes occurred in the Gökova Bay show N-S extension which is compatible with the palaeostress analyses of the Kızlan fault. This situation represents the ongoing activity along the northern margin of the Datça Graben.

Investigation of lineaments on Skylab and ERTS images of Peninsular Ranges, Southwestern California

NASA Technical Reports Server (NTRS)

Merifield, P. M. (Principal Investigator); Lamar, D. L.

1974-01-01

The author has identified the following significant results. Northwest trending faults such as the Elsinore and San Jacinto are prominently displayed on Skylab and ERTS images of the Peninsular Ranges, southern California. Northeast, north-south, and west-north-west trending lineaments and faults are also apparent on satellite imagery. Several of the lineaments represent previously unmapped faults. Other lineaments are due to erosion along foliation directions and sharp bends in basement rock contacts rather than faulting. The northeast trending Thing Valley fault appears to be offset by the south branch of the Elsinore fault near Agua Caliente Hot Springs. Larger horizontal displacement along the Elsinore fault further northwest may be distributed along several faults which branch from the Elsinore fault in the Peninsular Ranges. The northeast and west-northwest trending faults are truncated by the major northwest trending faults and appear to be restricted to basement terrane. Limited data on displacement direction suggests that the northeast and west-northwest trending faults formed in response to an earlier period of east-northeast, west-southwest crustal shortening. Such a stress system is consistent with the plate tectonic model of a subduction zone parallel to the continental margin suggested in the late Mesozoic and early Tertiary.

Tectonic inheritance, reactivation and long term fault weakening processes

NASA Astrophysics Data System (ADS)

Holdsworth, Bob

2017-04-01

This talk gives a geological review of weakening processes in faults and their long-term effect on reactivation and tectonic inheritance during crustal deformation. Examples will be drawn from the Atlantic margins, N America, Japan and the Alps. Tectonic inheritance and reactivation are fundamentally controlled by the processes of stress concentration and shear localisation manifested at all scales in the continental lithosphere. Lithosphere-scale controls include crustal thickness, thermal age and the boundary conditions imposed by the causative plate tectonic processes during extension. At the other end of the scale range, grain-scale controls include local environmental controls (depth, stress, strain rate), rock composition, grainsize, fabric intensity and the presence of fluids or melt. Intermediate-scale geometric controls are largely related to the size, orientation and interconnectivity of pre-existing anisotropies. If reactivation of pre-existing structures occurs, it likely requires a combination of processes across all three scale ranges to be favourable. This can make the unequivocal recognition of inheritance and reactivation difficult. Large (e.g. crustal-scale) pre-existing structures are especially important due to their ability to efficiently concentrate stress and localise strain. For big faults (San Andreas, Great Glen, Median Tectonic Line), detailed studies of the associated exposed fault rocks indicate that reactivation is linked to the development of strongly anisotropic phyllosilicate-rich fault rocks that are weak (e.g. friction coefficients as low as 0.2 or less) under a broad range of deformation conditions. In the case of pre-existing regional dyke swarms (S Atlantic, NW Scotland) - which may themselves track deep mantle fabrics at depth - multiple reactivation of dyke margins is widespread and may preclude reactivation of favourably oriented local basement fabrics. In a majority of cases, pre-existing structures in the crust are significantly oblique (<70°) to far field stress orientations. As a result, even quite modest amounts of reactivation will inevitably lead to transtensional/transpressional strains involving variable components of strike-slip and extension or shortening. The occurrence of bulk non-coaxial, non-plane strain leads to strain partitioning and/or (non-Andersonian) multimodal fracturing where the deformation cannot be described or reconstructed in single 2D cross-sectional or map view. Further complications can arise due to repeated seismogenic rupturing of larger offset faults leading to local stress transfer and reactivation of widely distributed smaller pre-existing structures in the wall rocks (e.g. Adamello Massif, Alps). The Atlantic margins demonstrate that pre-existing structures can influence deformation patterns across a range of scales, but such reactivation should never be assumed to be the norm. In many cases, the scales of faulting and displacement magnitudes associated with these reactivation events are modest compared to the regional-scale deformation of the margin. However, reactivation most certainly does influence the kilometre and smaller-scale complexity of faults, fractures and folds. It will therefore impact significantly on the development of geological architectures and their economic importance, e.g. location and nature of fluid channelways, trap geometries, reservoir performance, etc.

Perceived Marginalization and the Prediction of Romantic Relationship Stability

ERIC Educational Resources Information Center

Lehmiller, Justin J.; Agnew, Christopher R.

2007-01-01

The present research examined how perceived marginalization of one's romantic relationship is associated with level of future commitment to and stability of that involvement. Results from a 7-month longitudinal study of romantically involved individuals (N = 215) revealed that perceived social network marginalization at Time 1 predicted breakup…

Strong interseismic coupling, fault afterslip, and viscoelastic flow before and after the Oct. 9, 1995 Colima-Jalisco earthquake: continuous GPS measurements from Colima, Mexico

USGS Publications Warehouse

Azua, B.M.; DeMets, C.; Masterlark, Timothy

2002-01-01

Continuous GPS measurements from Colima, Mexico during 4/93-6/01, bracketing the Oct. 9, 1995 M = 8.0 Colima-Jalisco earthquake, provide new constraints on Rivera plate subduction mechanics. Modeling of margin-normal strain accumulation before the earthquake suggests the Rivera-North America subduction interface was fully locked. Transient postseismic motion from 10/ 95-6/97 is well fit by a model that includes logarithmically-decaying fault afterslip, elastic strain from shallow fault relocking, and possibly a minor viscoelastic response, but is fit poorly by models that assume a dominant Maxwell viscoelastic response of the lower crust and upper mantle, independent of the assumed viscosities. Landward, margin-normal motion since mid-1997 is parallel to but ??? 75% slower than the pre-seismic velocity. Afterslip alone fails to account for this slowdown. The viscoelastic response predicted by a FEM correctly resolves the remaining velocity difference within the uncertainties. Both processes thus offset elastic strain accumulating from the relocked subduction interface.

The Eastern Sardinian Margin (Tyrrhenian Sea, Western Mediterranean) : a key area to study the rifting and post-breakup evolution of a back-arc passive continental margin

NASA Astrophysics Data System (ADS)

Gaullier, Virginie; Chanier, Frank; Vendeville, Bruno; Maillard, Agnès; Thinon, Isabelle; Graveleau, Fabien; Lofi, Johanna; Sage, Françoise

2016-04-01

The Eastern Sardinian passive continental margin formed during the opening of the Tyrrhenian Sea, which is a back-arc basin created by continental rifting and oceanic spreading related to the eastward migrating Apennine subduction system (middle Miocene to Pliocene). Up to now, rifting in this key area was considered to be pro parte coeval with the Messinian Salinity Crisis (MSC, 5.96-5.32 Ma). We use the MSC seismic markers and the deformation of viscous salt and its brittle overburden as proxies to better delineate the timing of rifting and post-rift reactivation, and especially to quantify vertical and horizontal movements. On this young, highly-segmented margin, the Messinian Erosion Surface and the Upper and Mobile Units are systematically associated, respectively, to basement highs and deeper basins, showing that a rifted deep-sea domain already existed by Messinian times, therefore a major pre-MSC rifting episode occurred across the entire domain. Data show that there are no signs of Messinian syn-rift sediments, hence no evidence for rifting after Late Tortonian times. Moreover, because salt tectonics creates fan-shaped geometries in sediments, syn-rift deposits have to be carefully re-examined to distinguish the effects of crustal tectonics (rifting) and salt tectonics. We also precise that rifting is clearly diachronous from the upper margin (East-Sardinia Basin) to the lower margin (Cornaglia Terrace) with two unconformities, attributed respectively to the necking and to the lithospheric breakup unconformities. The onshore part of the upper margin has been recently investigated in order to characterize the large crustal faults affecting the Mesozoic series (geometry, kinematics and chronology) and to decipher the role of the structural inheritance and of the early rifting. Seaward, we also try to constrain the architecture and timing of the continent-ocean transition, between the hyper-extended continental crust and the first oceanic crust. Widespread post-breakup deformation also occurred during the Pliocene. Some Pliocene vertical movements have been evidenced by discovering localized gravity gliding of the salt and its Late Messinian (UU) and Early Pliocene overburden. To the South, crustal-scale southward tilting triggered along-strike gravity gliding of salt and cover recorded by upslope extension and downslope shortening. To the North, East of the Baronie Ridge, there was some post-salt crustal activity along a narrow N-S basement trough, bounded by crustal faults. The salt geometry would suggest that nothing happened after Messinian times, but some structural features (confirmed by analogue modelling) show that basement fault slip was accommodated by lateral salt flow, which thinned upslope and thickened downslope, while the overlying sediments remained sub-horizontal. Along the inner domain of Eastern Sardinian margin, the post-rift deformation style greatly varies. Compressional structures (reverse faults and folds) are observed both onshore and offshore while post-rift extensional structures are mainly identified offshore. Such late deformation could be attributed to mechanisms acting alone or combined, such as : i. the reactivation of the margin, as already described for the Ligurian, Algerian or South-Balearic margins due to the Eurasian-African convergence ; 2. the Zanclean reflooding and the resulting water overload on the elastic lithosphere ; 3. an episodic mantle upwelling.

Sliding mode based fault detection, reconstruction and fault tolerant control scheme for motor systems.

PubMed

Mekki, Hemza; Benzineb, Omar; Boukhetala, Djamel; Tadjine, Mohamed; Benbouzid, Mohamed

2015-07-01

The fault-tolerant control problem belongs to the domain of complex control systems in which inter-control-disciplinary information and expertise are required. This paper proposes an improved faults detection, reconstruction and fault-tolerant control (FTC) scheme for motor systems (MS) with typical faults. For this purpose, a sliding mode controller (SMC) with an integral sliding surface is adopted. This controller can make the output of system to track the desired position reference signal in finite-time and obtain a better dynamic response and anti-disturbance performance. But this controller cannot deal directly with total system failures. However an appropriate combination of the adopted SMC and sliding mode observer (SMO), later it is designed to on-line detect and reconstruct the faults and also to give a sensorless control strategy which can achieve tolerance to a wide class of total additive failures. The closed-loop stability is proved, using the Lyapunov stability theory. Simulation results in healthy and faulty conditions confirm the reliability of the suggested framework. Copyright © 2015 ISA. Published by Elsevier Ltd. All rights reserved.

Late Miocene extension partitioning in the eastern Betics: from W- to E-directed extension between the Sorbas and Vera basins (SE Spain).

NASA Astrophysics Data System (ADS)

Giaconia, Flavio; Booth-Rea, Guillermo; Martínez-Martínez, Jose Miguel; Azañon, Jose Miguel

2014-05-01

Late Miocene westward-directed extension in the Betics produced elongated core-complexes like Sierra Nevada and the Sierra de Filabres, tilted-block domains and associated basins. This extension represents the superficial manifestation of the rupture of the Tethyan slab and associated edge delamination along a lithospheric transform fault beneath the northern branch of the Gibraltar Arc orogenic system. However, crustal thinning at the eastern Betics occurs progressively towards the east suggesting an eastward-directed extension, probably related to the late Miocene opening of the Algero-Balearic basin. In order to define the kinematics and timing of such a heterogeneous extension at the eastern Betics we have carefully mapped a key area at the transition between the Sorbas and Vera basins. Field data indicate that extension in the area started at the southern margin of the Vera basin during the Serravallian (13.8 Ma) and continued until the Tortonian (approximately 8 Ma). This extension was characterized by a set of NE- to E-directed normal faults to the east, in the Vera basin, and a set of SW-directed normal faults to the west, towards the Sorbas basin. This opposite-directed extension is segmented by E-W to WNW-ESE strike-slip faults like the North Cabrera dextral transfer fault that accommodates NE- to E-directed extension to the north and SW-directed extension to the south. This structure resulted in westward tilted blocks that lead to Serravallian-Tortonian depocenters deepening towards the east at the Vera basin along the northern side of Sierra Cabrera. Meanwhile, at the western termination of Sierra Cabrera, westward-directed extension migrated SW-ward forming the Sorbas basin during the Tortonian (approximately 9-7.24 Ma). This extension was characterized by a listric fan of SW-directed normal faults highly segmented by E-W to NE-SW transfer. This extensional system produced tiled-blocks defining a Tortonian depocenter at the eastern margin of the Sorbas basin. This westward migration of extension followed very closely the apatite fission track cooling ages obtained from Nevado-Filabride samples exhumed at the Sierra de Filabres core-complex, to the north. These ages range between 15 and 11 Ma, to the east, and between 9.5 and 7.5 Ma, to the west. The westward migration of extension continued during the Messinian and the Quaternary affecting the Níjar basin where a SW-directed normal-fault system occurs. Heterogeneous extension in the region resulted in different extensional domains both in extension direction and style. These domains are separated by transfer faults as the North Cabrera dextral fault, which accommodated opposite tilted-block domains at the southern margin of the Vera basin. Similarly, the Carboneras sinistral fault separates the Níjar tilted-block domain, to the north, from the Cabo de Gata domain characterized by magmatic accretion upon previously thinned continental crust, to the south.

Great earthquakes along the Western United States continental margin: implications for hazards, stratigraphy and turbidite lithology

NASA Astrophysics Data System (ADS)

Nelson, C. H.; Gutiérrez Pastor, J.; Goldfinger, C.; Escutia, C.

2012-11-01

We summarize the importance of great earthquakes (Mw ≳ 8) for hazards, stratigraphy of basin floors, and turbidite lithology along the active tectonic continental margins of the Cascadia subduction zone and the northern San Andreas Transform Fault by utilizing studies of swath bathymetry visual core descriptions, grain size analysis, X-ray radiographs and physical properties. Recurrence times of Holocene turbidites as proxies for earthquakes on the Cascadia and northern California margins are analyzed using two methods: (1) radiometric dating (14C method), and (2) relative dating, using hemipelagic sediment thickness and sedimentation rates (H method). The H method provides (1) the best estimate of minimum recurrence times, which are the most important for seismic hazards risk analysis, and (2) the most complete dataset of recurrence times, which shows a normal distribution pattern for paleoseismic turbidite frequencies. We observe that, on these tectonically active continental margins, during the sea-level highstand of Holocene time, triggering of turbidity currents is controlled dominantly by earthquakes, and paleoseismic turbidites have an average recurrence time of ~550 yr in northern Cascadia Basin and ~200 yr along northern California margin. The minimum recurrence times for great earthquakes are approximately 300 yr for the Cascadia subduction zone and 130 yr for the northern San Andreas Fault, which indicates both fault systems are in (Cascadia) or very close (San Andreas) to the early window for another great earthquake. On active tectonic margins with great earthquakes, the volumes of mass transport deposits (MTDs) are limited on basin floors along the margins. The maximum run-out distances of MTD sheets across abyssal-basin floors along active margins are an order of magnitude less (~100 km) than on passive margins (~1000 km). The great earthquakes along the Cascadia and northern California margins cause seismic strengthening of the sediment, which results in a margin stratigraphy of minor MTDs compared to the turbidite-system deposits. In contrast, the MTDs and turbidites are equally intermixed on basin floors along passive margins with a mud-rich continental slope, such as the northern Gulf of Mexico. Great earthquakes also result in characteristic seismo-turbidite lithology. Along the Cascadia margin, the number and character of multiple coarse pulses for correlative individual turbidites generally remain constant both upstream and downstream in different channel systems for 600 km along the margin. This suggests that the earthquake shaking or aftershock signature is normally preserved, for the stronger (Mw ≥ 9) Cascadia earthquakes. In contrast, the generally weaker (Mw = or <8) California earthquakes result in upstream simple fining-up turbidites in single tributary canyons and channels; however, downstream mainly stacked turbidites result from synchronously triggered multiple turbidity currents that deposit in channels below confluences of the tributaries. Consequently, both downstream channel confluences and the strongest (Mw ≥ 9) great earthquakes contribute to multi-pulsed and stacked turbidites that are typical for seismo-turbidites generated by a single great earthquake. Earthquake triggering and multi-pulsed or stacked turbidites also become an alternative explanation for amalgamated turbidite beds in active tectonic margins, in addition to other classic explanations. The sedimentologic characteristics of turbidites triggered by great earthquakes along the Cascadia and northern California margins provide criteria to help distinguish seismo-turbidites in other active tectonic margins.

Metallogenesis and tectonics of the Russian Far East, Alaska, and the Canadian Cordillera

USGS Publications Warehouse

Nokleberg, Warren J.; Bundtzen, Thomas K.; Eremin, Roman A.; Ratkin, Vladimir V.; Dawson, Kenneth M.; Shpikerman, Vladimir I.; Goryachev, Nikolai A.; Byalobzhesky, Stanislav G.; Frolov, Yuri F.; Khanchuk, Alexander I.; Koch, Richard D.; Monger, James W.H.; Pozdeev, Anany I.; Rozenblum, Ilya S.; Rodionov, Sergey M.; Parfenov, Leonid M.; Scotese, Christopher R.; Sidorov, Anatoly A.

2005-01-01

The Proterozoic and Phanerozoic metallogenic and tectonic evolution of the Russian Far East, Alaska, and the Canadian Cordillera is recorded in the cratons, craton margins, and orogenic collages of the Circum-North Pacific mountain belts that separate the North Pacific from the eastern North Asian and western North American Cratons. The collages consist of tectonostratigraphic terranes and contained metallogenic belts, which are composed of fragments of igneous arcs, accretionary-wedge and subduction-zone complexes, passive continental margins, and cratons. The terranes are overlapped by continental-margin-arc and sedimentary-basin assemblages and contained metallogenic belts. The metallogenic and geologic history of terranes, overlap assemblages, cratons, and craton margins has been complicated by postaccretion dismemberment and translation during strike-slip faulting that occurred subparallel to continental margins. Seven processes overlapping in time were responsible for most of metallogenic and geologic complexities of the region (1) In the Early and Middle Proterozoic, marine sedimentary basins developed on major cratons and were the loci for ironstone (Superior Fe) deposits and sediment-hosted Cu deposits that occur along both the North Asia Craton and North American Craton Margin. (2) In the Late Proterozoic, Late Devonian, and Early Carboniferous, major periods of rifting occurred along the ancestral margins of present-day Northeast Asia and northwestern North America. The rifting resulted in fragmentation of each continent, and formation of cratonal and passive continental-margin terranes that eventually migrated and accreted to other sites along the evolving margins of the original or adjacent continents. The rifting also resulted in formation of various massive-sulfide metallogenic belts. (3) From about the late Paleozoic through the mid-Cretaceous, a succession of island arcs and contained igneous-arc-related metallogenic belts and tectonically paired subduction zones formed near continental margins. (4) From about mainly the mid-Cretaceous through the present, a succession of continental-margin igneous arcs (some extending offshore into island arcs) and contained metallogenic belts, and tectonically paired subduction zones formed along the continental margins. (5) From about the Jurassic to the present, oblique convergence and rotations caused orogen-parallel sinistral, and then dextral displacements within the plate margins of the Northeast Asian and North American Cratons. The oblique convergences and rotations resulted in the fragmentation, displacement, and duplication of formerly more continuous arcs, subduction zones, passive continental margins, and contained metallogenic belts. These fragments were subsequently accreted along the margins of the expanding continental margins. (6) From the Early Jurassic through Tertiary, movement of the upper continental plates toward subduction zones resulted in strong plate coupling and accretion of the former island arcs, subduction zones, and contained metallogenic belts to continental margins. In this region, the multiple arc accretions were accompanied and followed by crustal thickening, anatexis, metamorphism, formation of collision-related metallogenic belts, and uplift; this resulted in the substantial growth of the North Asian and North American continents. (7) In the middle and late Cenozoic, oblique to orthogonal convergence of the Pacific Plate with present-day Alaska and Northeast Asia resulted in formation of the present ring of volcanoes and contained metallogenic belts around the Circum-North Pacific. Oblique convergence between the Pacific Plate and Alaska also resulted in major dextral-slip faulting in interior and southern Alaska and along the western part of the Aleutian- Wrangell arc. Associated with dextral-slip faulting was crustal extrusion of terranes from western Alaska into the Bering Sea.

Spatial variations in fluvial incision across the eastern margin of Tibet reveal locus of deformation in the deep crust

NASA Astrophysics Data System (ADS)

Kirby, Eric

2017-04-01

The manifestation of coupling among climate, erosion and tectonics along steep topographic margins of orogenic plateaus is strongly dependent on the processes driving crustal thickening. Along the eastern margin of the Tibetan Plateau, a long-standing and vigorous debate persists over whether mountain building occurred largely along upper-crustal faults or was the consequence of distributed thickening in the lower crust. Here I revisit this debate and show how surface deformation recorded by geomorphology over millennial timescales (10^4-105 yr) can yield insight into the role the deep crust along plateau margins. In contrast to the intensively studied Longmen Shan, the topographic margin of the Tibetan Plateau north of the Sichuan Basin follows the north-south Min Shan and cuts orthogonally across the structural grain of the Mesozoic West Qinling orogen. The lack of a direct association of topography with upper crustal faults affords an opportunity to evaluate the patterns of differential rock uplift from geomorphology. First, I employ an empirical calibration of river profile steepness (channel gradient normalized for drainage basin area) and erosion rate from cosmogenic 10Be concentrations in modern sediment. Application to the channels draining the plateau margin reveals a locus of high (300-500 m/Myr) erosion rate coincident with the Min Shan. Second, I present new results of surveying and dating of fluvial terraces developed along the Bailong Jiang, one of the major rivers draining across the plateau margin. A preliminary chronology of terrace formation and abandonment based on radiocarbon and OSL dating of fluvial deposits reveals systematic spatial gradients in fluvial incision, with highest incision rates (1000-2000 m/Myr) localized along the axis of the Min Shan and decreasing toward both the foreland and the plateau. This locus of incision has apparently been sustained through multiple generations of terrace formation and abandonment since at least 80 ka and thus is interpreted to reflect sustained differential rock uplift along this axis. The wavelength of the region of highest incision rates is 80 km and requires either 1) a deeply buried tip of a blind fault, or 2) thickening in the deep crust. We argue that terrace deformation and associated rock uplift likely reflects flow and thickening of deep Tibetan crust against the foreland of the West Qinling.

Spatial variations in fluvial incision across the eastern margin of Tibet reveal locus of thickening in the deep crust

NASA Astrophysics Data System (ADS)

Kirby, Eric; Zhang, Huiping; Chen, Jie

2016-04-01

The manifestation of coupling among climate, erosion and tectonics along steep topographic margins of orogenic plateaus is strongly dependent on the processes driving crustal thickening. Along the eastern margin of the Tibetan Plateau, a long-standing an vigorous debate persists over whether mountain building occurred largely along upper-crustal faults or was the consequence of distributed thickening in the lower crust. Here we revisit this debate and show how surface deformation recorded by geomorphology over millennial timescales (104-105 yr) can yield insight into the role the deep crust along plateau margins. In contrast to the intensively studied Longmen Shan, the topographic margin of the Tibetan Plateau north of the Sichuan Basin follows the north-south Min Shan and cuts orthogonally across the structural grain of the Mesozoic West Qinling orogen. The lack of a direct association of topography with upper crustal faults affords an opportunity to evaluate the patterns of differential rock uplift from geomorphology. First, we employ an empirical calibration of river profile steepness (channel gradient normalized for drainage basin area) and erosion rate from cosmogenic 10Be concentrations in modern sediment. Application to the channels draining the plateau margin reveals a locus of high (300-500 m/Myr) erosion rate coincident with the Min Shan. Second, we present new results of surveying and dating of fluvial terraces developed along the Bailong Jiang, one of the major rivers draining across the plateau margin. A preliminary chronology of terrace tread deposits based on radiocarbon and OSL samples reveals systematic spatial gradients in fluvial incision, with highest incision rates (1000-2000 m/Myr) localized along the axis of the Min Shan and decreasing toward both the foreland and the plateau. This locus of incision has apparently been sustained through multiple generations of terrace formation and abandonment since ca. 80ka and thus is interpreted to reflect sustained differential rock uplift along this axis. The wavelength of the region of highest incision rates is ˜80 km and requires either 1) a deeply buried tip of a blind fault, or 2) thickening in the deep crust. We argue that terrace deformation and associated rock uplift likely reflects flow and thickening of deep Tibetan crust against the foreland of the West Qinling.

Marine Ice Crevassing Imaged with Side-looking GPR: Implications for Stability within the McMurdo Shear Zone

NASA Astrophysics Data System (ADS)

Arcone, S. A.; Ray, L.; Lever, J.; Koons, P. O.; Kaluzienski, L. M.

2017-12-01

Shearing along ice shelf margins threatens shelf stability if crevassing results throughout the ice. We are investigating a 28 km2 section of the McMurdo Shear Zone (MSZ), which lies between the Ross Ice Shelf (RIS) and the McMurdo Ice Shelf (MIS). Our gridded transects are east-west, ice flow is nearly due north and the RIS compresses against the MIS from east to west. We find nearly synchronized firn and marine ice crevassing; the marine ice is stratified. However, the lack of any radar evidence for crevassing or fracture within the intermediate 120 m of meteoric ice is so far, enigmatic. The marine ice crevassing is interpreted from ground-penetrating radar (GPR) trace signatures within 100 m swaths of the interface between the meteoric and marine ice; thus the GPR performs like side-looking radar. Symmetric and deformed diffraction hyperbolas indicate crevasses oriented at 43-76 degrees relative to ice flow, as seen in the firn. Those near 45 degrees are interpreted as recently formed while those at greater angles are likely older and rotated. Many traces indicate crevasse warping, lateral faulting, and down-faulting. Traces nearly perpendicular to flow indicate possible wing cracks that grew from the tips of crevasses into the direction of compression from the RIS. We interpret the marine crevasses to have originated at the meteoric-marine interface, and to have extended to the shelf bottom because they appear filled with unstratified frozen seawater. In view of these observations, and that the intermediate meteoric ice must be under similar although not exactly the same stresses, the lack of fracturing within the meteoric ice may imply that suturing following brittle and ductile shear deformation provides stability for the MSZ and may result from this east-west compression of the RIS against the MIS.

Tectonic controls on rift basin morphology: Evolution of the northern Malawi (Nyasa) rift

NASA Technical Reports Server (NTRS)

Ebinger, C. J.; Deino, A. L.; Tesha, A. L.; Becker, T.; Ring, U.

1993-01-01

Radiometric (K-Ar and Ar-40/Ar-39) age determinations of volcanic and volcaniclastic rocks, combined with structural, gravity, and seismic reflection data, are used to constrain the age of sedimentary strata contained within the seismically and volcanically active northern Malawi (Nyasa) rift and to characterize changes in basin and flank morphologies with time. Faulting and volcanism within the Tukuyu-Karonga basin began at approximately 8.6 Ma, when sediments were deposited in abroad, initially asymmetric lake basin bounded on its northeastern side by a border fault system with minor topographic relief. Extensions, primarily by a slip along the border fault, and subsequent regional isostatic compensation led to the development of a 5-km-deep basin bounded by broad uplifted flanks. Along the low-relief basin margin opposite border fault, younger stratigraphic sequences commonly onlap older wedge-shaped sequences, although their internal geometry is often progradational. Intrabasinal faulting, flankuplift, and basaltic and felsic volcanism from centers at the northern end of the basin became more important at about 2.5 Ma when cross-rift transfer faults developed to link the Tukuyu-Karonga basin to the Rukwa basin. Local uplift and volcanic construction at the northern end of the basin led to a southeastward shift in the basin's depocenter. Sequence boundaries are commonly erosional along this low-relief (hanging wall) margin and conformable in the deep lake basin. The geometry of stratigraphic sequences and the distribution of the erosion indicate that horizontal and vertical crustal movements both across and along the length of the rift basin led to changes in levels of the lake, irrespective of paleoclimatic fluctuations.

Structural Evolution of central part of the Tuzgolu (Salt Lake) Basin, Central Anatolia, Turkey

NASA Astrophysics Data System (ADS)

Ada, M.; Cemen, I.; Çaptuğ, A.; Demirci, M.; Engin, C.

2017-12-01

The Tuzgolu Basin in Central Anatolia, Turkey, covers low-relief areas located between the Pontide Mountains to the North and Tauride Mountains to the South. The basin started to form as a rift basin during the Late Maastrichtian. The main Tuzgolu-Aksaray fault zone on the eastern margin of the basin and the northwest trending Yeniceoba and Cihanbeyli fault zones on the western margin of the basin were probably developed during that time. The basin has also experienced westward extension in response to westward escape of the Anatolian plate since Late Miocene. Several geologic studies have been conducted in the Tuz Gölü (Salt Lake) Basin and surrounding areas to determine structural and tectono-stratigraphic development of the basin. However, there are still many questions regarding the structural evolution of the basin. The main purpose of this study is to investigate the structural evolution of the central Tuzgolu Basin based on the structural interpretation of available 2-D seismic reflection profiles, well log analysis and construction of structural cross sections. The cross-sections will be based on depth converted seismic lines to determine structural geometry of the faults and folds. A preliminary Petrel project has been prepared using available seismic profiles. Our preliminary structural interpretations suggest that a well-developed rollover anticline was developed with respect to the westward extension in Central Anatolia. The rollover anticline is faulted in its crest area by both down-to-the west and down-to-the east normal faults. The geometry of the main boundary fault at depth still remains in question. We anticipate that this question will be resolved based on depth converted structural cross-sections and their restoration.

A Self-Stabilizing Hybrid Fault-Tolerant Synchronization Protocol

NASA Technical Reports Server (NTRS)

Malekpour, Mahyar R.

2015-01-01

This paper presents a strategy for solving the Byzantine general problem for self-stabilizing a fully connected network from an arbitrary state and in the presence of any number of faults with various severities including any number of arbitrary (Byzantine) faulty nodes. The strategy consists of two parts: first, converting Byzantine faults into symmetric faults, and second, using a proven symmetric-fault tolerant algorithm to solve the general case of the problem. A protocol (algorithm) is also present that tolerates symmetric faults, provided that there are more good nodes than faulty ones. The solution applies to realizable systems, while allowing for differences in the network elements, provided that the number of arbitrary faults is not more than a third of the network size. The only constraint on the behavior of a node is that the interactions with other nodes are restricted to defined links and interfaces. The solution does not rely on assumptions about the initial state of the system and no central clock nor centrally generated signal, pulse, or message is used. Nodes are anonymous, i.e., they do not have unique identities. A mechanical verification of a proposed protocol is also present. A bounded model of the protocol is verified using the Symbolic Model Verifier (SMV). The model checking effort is focused on verifying correctness of the bounded model of the protocol as well as confirming claims of determinism and linear convergence with respect to the self-stabilization period.

Geometry, structure, and concealed lithology of the San Rafael Basin, southeastern Arizona

USGS Publications Warehouse

Bultman, Mark W.

1999-01-01

The contiguous United States has been well explored for exposed conventional mineral deposits. Therefore, it is likely that many economically viable and strategically significant conventional undiscovered mineral deposits will be found in bedrock concealed beneath basin sediments. Mineral resource assessments must incorporate an understanding of the geometry, structure, and concealed lithology of basins in order to be accurate. This report presents an analysis of the basin geometry and structure of the San Rafael basin in southeastern Arizona. In addition, a new methodology for inferring concealed lithology is presented and applied in the San Rafael basin. Gravity data is used to model the geometry of the basin using recent models of sediment density vs. depth developed in the region. This modeling indicates that the basin has a maximum depth of approximately 1.05 km plus or minus 0.10 km. In the southern portion, the basin can be modeled as an asymmetric graben faulted on the western margin. The northern portion of the basin is structurally more complex and may have high angle faults on the western, northern, and eastern margin. Near-ground closely spaced Earth’s total intensity magnetic field data is used to locate concealed faults within the basin. This data is also used to infer lithology concealed by shallow basin sediments. Airborne Earth’s total intensity magnetic field data is used to help infer concealed lithology in deep portions of the basin. The product of integrating all data and interpretations is a map which presents the geometry of the basin, faults and contacts concealed by basin sediments, and an estimate of the bedrock lithology concealed by basin sediment. Based on basin geometry and concealed lithology, the San Rafael basin has a high potential for concealed mineral deposits on its western and northern margin. In particular, a newly discovered magnetic anomaly in the northern portion of the basin can be modeled as a granitic intrusion with highly altered margins and may represent a potential mineral resource target. Based on the permeability and porosity of upper basin fill found in nearby basins, the San Rafael basin may contain an aquifer up to 300 meters thick over a substantial area of the basin.

New marine data from Vietnam Margin limit the amount of extrusion of Indochina during the opening of the South China Sea

DOE Office of Scientific and Technical Information (OSTI.GOV)

Huchon, P.; Le Pichon, X.; Rangin, C.

1994-07-01

A total of 9300 km of high resolution, wide coverage multibeam (Simrad EM12) bathymetric data have been acquired offshore Vietnam during the Ponaga cruise of the R/V L'Atalante in May 1993. Gravity and magnetic measurements, 6-channel seismic data, as well as 6 dredges also have been obtained. East of central Vietnam, the margin displays northeast-southwest tectonic structures typical of a passive margin. The depth of the basement of the Nha Trang basin suggests that it could be of oceanic nature, with a 20 to 30 Ma age compatible with the age of the South China Sea oceanic crust located furthermore » east. Southeast of South Vietnam, the authors identified the western tip of the fossil axis of the South China Sea. It constitutes a propagating ridge into a highly stretched continental crust, partly intruded by volcanics. East of 110[degrees]30[prime]E, tilted blocks are symmetric with respect to the oceanic axis, whereas west of 110[degrees]30[prime]E they are mostly tilted toward the south, which suggests the occurrence a large listric normal fault associated with a large amount of extension. The normal faults bend progressively to a more northerly direction when approaching the north-south scarp that bounds the Conson basin. This geometry is compatible with a right-lateral motion, and the normal faults associated with the oceanic propagator suggest that the dextral motion is synchronous with at least the last phase of spreading in the South China Sea (23-16 Ma). Since recent offshore oil data have established that the prolongation of the Red River fault within the Gulf of Tonkin was affected by left-lateral motion from the Oligocene to the upper Miocene, the results suggest that the change from left-lateral motion in the Gulf of Tonkin to right-lateral motion along the Vietnam margin occurs because the South China Sea basin opens more rapidly than the extrusion of Indochina. Thus, the total amount of extrusion of Indochina probably does not exceed 100 or 200 km.« less

Volcano-tectonic evolution of the Western Afar margin: new geochronological and structural data

NASA Astrophysics Data System (ADS)

Stab, Martin; Pik, Raphael; Bellahsen, Nicolas; Leroy, Sylvie; Ayalew, Dereje; Denèle, Yoann

2013-04-01

The rift system in NW-Afar (Ethiopia) is part of the Nubia-Somalia-Arabia triple junction located above the Afar hot spot active mainly since Oligocene times. It represents a unique natural laboratory for field study of superficial and deep lithospheric structure and process interactions during the transition between rifting and oceanic spreading in magma-rich setting. Most past field studies in Afar focused on the recognition and correlation of Afar's volcano-stratigraphic record and led to models of margin development that stress out the major trends of volcanic structures and give accordingly the following chronological "big picture". (1) 2km-thick flood basalt province emplaced at ca. 30 Ma due to hot spot activity over Jurassic to Permian sedimentary rocks and basement. (2) Rifting started around 25-20 Ma with half graben and great escarpment formation along with localization of volcanic activity in highly faulted narrower basins followed by lithospheric flexure. (3) The deformation migrated toward the rift centre with the emplacement around 8-5 Ma of bi-modal volcanics later faulted. (4) A second pulse of flood-basalt, the so-called Stratoid series, started at 4 Ma, until 1 Ma. In this contribution, we present new structural field data and lavas (U-Th/He) datings along a cross-section from the marginal graben to the Manda-Hararo active rift axis. In the newly explored Sullu Adu ranges, which were previously thought to be made of 8 Ma Dahla Basalts Fm., we mapped normal faults arrays affecting a complex magmatic series. We dated highly tilted 30 Ma pre-rift basic and silicic volcanic rocks that are unconformably overlain by syn-rift volcanics (25 to 8 Ma). This pattern is in some places either masked by unconformable thick stratoid cover or strongly eroded by dense river drainage. However, it is preserved enough to suggest a lower-than-expected extension ratio and/or the presence of major normal faults controlling seaward-dipping reflectors (SDR) emplacement such as the one observed on seismic reflection profiles in North and South Atlantic volcanic margins.

Flexure in the Corinth rift: reconciling marine terraces, rivers, offshore data and fault modeling

NASA Astrophysics Data System (ADS)

de Gelder, G.; Fernández-Blanco, D.; Jara-Muñoz, J.; Melnick, D.; Duclaux, G.; Bell, R. E.; Lacassin, R.; Armijo, R.

2016-12-01

The Corinth rift (Greece) is an exceptional area to study the large-scale mechanics of a young rift system, due to its extremely high extension rates and fault slip rates. Late Pleistocene activity of large normal faults has created a mostly asymmetric E-W trending graben, mainly driven by N-dipping faults that shape the southern margin of the Corinth Gulf. Flexural footwall uplift of these faults is evidenced by Late Pleistocene coastal fan deltas that are presently up to 1700m in elevation, a drainage reversal of some major river systems, and flights of marine terraces that have been uplifted along the southern margin of the Gulf. To improve constraints on this footwall uplift, we analysed the extensive terrace sequence between Xylokastro and Corinth - uplifted by the Xylokastro Fault - using 2m-resolution digital surface models developed from Pleiades satellite imagery (acquired through the Isis and Tosca programs of the French CNES). We refined and improved the spatial uplift pattern and age correlation of these terraces, through a detailed analysis of the shoreline angles using the graphical interface TerraceM, and 2D numerical modeling of terrace formation. We combine the detailed record of flexure provided by this analysis with a morphometric analysis of the major river systems along the southern shore, obtaining constraints of footwall uplift on a longer time scale and larger spatial scale. Flexural subsidence of the hanging wall is evidenced by offshore seismic sections, for which we depth-converted a multi-channel seismic section north of the Xylokastro Fault. We use the full profile of the fault geometry and its associated deformation pattern as constraints to reproduce the long-term flexural wavelength and uplift/subsidence ratio through fault modeling. Using PyLith, an open-source finite element code for quasi-static viscoelastic simulations, we find that a steep-dipping planar fault to the brittle-ductile transition provides the best fit to reproduce the observed deformation pattern on- and offshore. The combined results of this study allow us to compare flexural normal faulting on different scales, and recorded in different elements of the Corinth rift, allowing us to put forward a comprehensive discussion on the deformation mechanisms and the mechanical behavior of this crustal scale feature.

Evidence for large earthquakes on the San Andreas fault at the Wrightwood, California paleoseismic site: A.D. 500 to present

USGS Publications Warehouse

Fumal, T.E.; Weldon, R.J.; Biasi, G.P.; Dawson, T.E.; Seitz, G.G.; Frost, W.T.; Schwartz, D.P.

2002-01-01

We present structural and stratigraphic evidence from a paleoseismic site near Wrightwood, California, for 14 large earthquakes that occurred on the southern San Andreas fault during the past 1500 years. In a network of 38 trenches and creek-bank exposures, we have exposed a composite section of interbedded debris flow deposits and thin peat layers more than 24 m thick; fluvial deposits occur along the northern margin of the site. The site is a 150-m-wide zone of deformation bounded on the surface by a main fault zone along the northwest margin and a secondary fault zone to the southwest. Evidence for most of the 14 earthquakes occurs along structures within both zones. We identify paleoearthquake horizons using infilled fissures, scarps, multiple rupture terminations, and widespread folding and tilting of beds. Ages of stratigraphic units and earthquakes are constrained by historic data and 72 14C ages, mostly from samples of peat and some from plant fibers, wood, pine cones, and charcoal. Comparison of the long, well-resolved paleoseimic record at Wrightwood with records at other sites along the fault indicates that rupture lengths of past earthquakes were at least 100 km long. Paleoseismic records at sites in the Coachella Valley suggest that each of the past five large earthquakes recorded there ruptured the fault at least as far northwest as Wrightwood. Comparisons with event chronologies at Pallett Creek and sites to the northwest suggests that approximately the same part of the fault that ruptured in 1857 may also have failed in the early to mid-sixteenth century and several other times during the past 1200 years. Records at Pallett Creek and Pitman Canyon suggest that, in addition to the 14 earthquakes we document, one and possibly two other large earthquakes ruptured the part of the fault including Wrightwood since about A.D. 500. These observations and elapsed times that are significantly longer than mean recurrence intervals at Wrightwood and sites to the southeast suggest that at least the southermost 200 km of the San Andreas fault is near failure.

A Model of Subduction of a Mid-Paleozoic Oceanic Ridge - Transform Fault System along the Eastern North American Margin in the Northern Appalachians

NASA Astrophysics Data System (ADS)

Kuiper, Y. D.

2016-12-01

Crustal-scale dextral northeasterly trending ductile-brittle fault systems and increased igneous activity in mid-Paleozoic eastern New England and southern Maritime Canada are interpreted in terms of a subducted oceanic spreading ridge model. In the model, the fault systems form as a result of subduction of a spreading ridge-transform fault system, similar to the way the San Andreas fault system formed. Ridge subduction results in the formation of a sub-surface slab window, mantle upwelling, and increased associated magmatism in the overlying plate. The ridge-transform system existed in the Rheic Ocean, and was subducted below parts of Ganderia, Avalonia and Meguma in Maine, New Brunswick and Nova Scotia. The subduction zone jumped southeastward as a result of accretion of Avalonia. Where the ridge-transform system was subducted, plate motions changed from predominantly convergent between the northern Rheic Ocean and Laurentian plates to predominantly dextral between the southern Rheic Ocean and Laurentian plates. In the model, dextral fault systems include the Norumbega fault system between southwestern New Brunswick and southern Maine and New Hampshire, and the Kennebecasis, Belle Isle and Caledonia faults in southeastern New Brunswick. A latest Silurian transition from arc- to within-plate- magmatism in the Coastal Volcanic Belt in eastern Maine may suggest the onset of ridge subduction. Examples of increased latest Silurian to Devonian within-plate magmatism include the Cranberry Island volcanic series and coastal Maine magmatic province in Maine, and the South Mountain Batholith in Nova Scotia. Widespread Devonian to earliest Carboniferous granitic to intermediate plutons, beyond the Coastal Volcanic Belt towards southern Maine and central New Hampshire, may outline the shape of a subsurface slab window. The possibility of ridge-transform subduction in Newfoundland and in the southern Appalachians will be discussed. The northern Appalachians may be a unique location along the Eastern North American Margin and possibly on Earth, in that it may preserve the only known evidence for an ancient Mendocino-style triple junction and San Andreas-type fault.

Structure of the active rift zone and margins of the northern Imperial Valley from Salton Seismic Imaging Project (SSIP) data

NASA Astrophysics Data System (ADS)

Livers, A.; Han, L.; Delph, J. R.; White-Gaynor, A. L.; Petit, R.; Hole, J. A.; Stock, J. M.; Fuis, G. S.

2012-12-01

First-arrival refraction data were used to create a seismic velocity model of the upper crust across the actively rifting northern Imperial Valley and its margins. The densely sampled seismic refraction data were acquired by the Salton Seismic Imaging Project (SSIP) , which is investigating rift processes in the northern-most rift segment of the Gulf of California extensional province and earthquake hazards at the southern end of the San Andreas Fault system. A 95-km long seismic line was acquired across the northern Imperial Valley, through the Salton Sea geothermal field, parallel to the five Salton Butte volcanoes and perpendicular to the Brawley Seismic Zone and major strike-slip faults. Nineteen explosive shots were recorded with 100 m seismometer spacing across the valley and with 300-500 m spacing into the adjacent ranges. First-arrival travel times were picked from shot gathers along this line and a seismic velocity model was produced using tomographic inversion. Sedimentary basement and seismic basement in the valley are interpreted to be sediment metamorphosed by the very high heat flow. The velocity model shows that this basement to the west of the Brawley Seismic Zone is at ~4-km depth. The basement shallows to ~2-km depth in the active geothermal field and Salton Buttes volcanic field which locally coincide with the Brawley Seismic Zone. At the eastern edge of the geothermal field, the basement drops off again to ~3.5-km depth. The eastern edge of the valley appears to be fault bounded by the along-strike extension of the Sand Hills Fault, an inactive strike-slip fault. The seismic velocities to the east of the fault correspond to metamorphic rock of the Chocolate Mountains, different from the metamorphosed basement in the valley. The western edge of the valley appears to be fault bounded by the active Superstition Hills Fault. To the west of the valley, >4-km deep valley basement extends to the active Superstition Hills Fault. Basement then shallows westward towards exposures of granitic basement in the Superstition Mountains. The basin between the Superstition Mountains and Coyote Mountains is ~2 km deep.

Phasor Measurement Unit and Its Application in Modern Power Systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ma, Jian; Makarov, Yuri V.; Dong, Zhao Yang

2010-06-01

The introduction of phasor measuring units (PMUs) in power systems significantly improves the possibilities for monitoring and analyzing power system dynamics. Synchronized measurements make it possible to directly measure phase angles between corresponding phasors in different locations within the power system. Improved monitoring and remedial action capabilities allow network operators to utilize the existing power system in a more efficient way. Improved information allows fast and reliable emergency actions, which reduces the need for relatively high transmission margins required by potential power system disturbances. In this chapter, the applications of PMU in modern power systems are presented. Specifically, the topicsmore » touched in this chapter include state estimation, voltage and transient stability, oscillation monitoring, event and fault detection, situation awareness, and model validation. A case study using Characteristic Ellipsoid method based on PMU to monitor power system dynamic is presented.« less

Why have hydrostatic bearings been avoided as a stabilizing element for rotating machines

NASA Technical Reports Server (NTRS)

Bently, D. E.; Muszynska, A.

1985-01-01

The advantages are discussed of hydrostatic, high pressure bearings as providers of higher margin of stability to the rotor/bearing systems. It is apparent that deliberate use of hydrostatic bearing high pressure lubricated (any gas or liquid) can easily be used to build higher stability margin into rotating machinery, in spite of the thirty years bias against high pressure lubrication. Since this supply pressure is controllable (the Direct Dynamic Stiffness at lower eccentricity is also controllable) so that within some rotor system limits, the stability margin and dynamic response of the rotor system is more readily controllable. It may be possible to take advantage of this effect in the various seals, as well as the bearings, to assist with stability margin and dynamic response of rotating machinery. The stability of the bearing can be additionally improved by taking advantage of the anti-swirling concept. The high pressure fluid supply inlets should be located tangentially at the bearing circumference and directed against rotation. The incoming fluid flow creates stability by reducing the swirling rate.

The northwest trending north Boquerón Bay-Punta Montalva Fault Zone; A through going active fault system in southwestern Puerto Rico

USGS Publications Warehouse

Roig‐Silva, Coral Marie; Asencio, Eugenio; Joyce, James

2013-01-01

The North Boquerón Bay–Punta Montalva fault zone has been mapped crossing the Lajas Valley in southwest Puerto Rico. Identification of the fault was based upon detailed analysis of geophysical data, satellite images, and field mapping. The fault zone consists of a series of Cretaceous bedrock faults that reactivated and deformed Miocene limestone and Quaternary alluvial fan sediments. The fault zone is seismically active (local magnitude greater than 5.0) with numerous locally felt earthquakes. Focal mechanism solutions suggest strain partitioning with predominantly east–west left-lateral displacements with small normal faults striking mostly toward the northeast. Northeast-trending fractures and normal faults can be found in intermittent streams that cut through the Quaternary alluvial fan deposits along the southern margin of the Lajas Valley, an east–west-trending 30-km-long fault-controlled depression. Areas of preferred erosion within the alluvial fan trend toward the west-northwest parallel to the onland projection of the North Boquerón Bay fault. The North Boquerón Bay fault aligns with the Punta Montalva fault southeast of the Lajas Valley. Both faults show strong southward tilting of Miocene strata. On the western end, the Northern Boquerón Bay fault is covered with flat-lying Holocene sediments, whereas at the southern end the Punta Montalva fault shows left-lateral displacement of stream drainage on the order of a few hundred meters.

An update of Quaternary faults of central and eastern Oregon

USGS Publications Warehouse

Weldon, Ray J.; Fletcher, D.K.; Weldon, E.M.; Scharer, K.M.; McCrory, P.A.

2002-01-01

This is the online version of a CD-ROM publication. We have updated the eastern portion of our previous active fault map of Oregon (Pezzopane, Nakata, and Weldon, 1992) as a contribution to the larger USGS effort to produce digital maps of active faults in the Pacific Northwest region. The 1992 fault map has seen wide distribution and has been reproduced in essentially all subsequent compilations of active faults of Oregon. The new map provides a substantial update of known active or suspected active faults east of the Cascades. Improvements in the new map include (1) many newly recognized active faults, (2) a linked ArcInfo map and reference database, (3) more precise locations for previously recognized faults on shaded relief quadrangles generated from USGS 30-m digital elevations models (DEM), (4) more uniform coverage resulting in more consistent grouping of the ages of active faults, and (5) a new category of 'possibly' active faults that share characteristics with known active faults, but have not been studied adequately to assess their activity. The distribution of active faults has not changed substantially from the original Pezzopane, Nakata and Weldon map. Most faults occur in the south-central Basin and Range tectonic province that is located in the backarc portion of the Cascadia subduction margin. These faults occur in zones consisting of numerous short faults with similar rates, ages, and styles of movement. Many active faults strongly correlate with the most active volcanic centers of Oregon, including Newberry Craters and Crater Lake.

The Tjellefonna fault system of Western Norway: Linking late-Caledonian extension, post-Caledonian normal faulting, and Tertiary rock column uplift with the landslide-generated tsunami event of 1756

NASA Astrophysics Data System (ADS)

Redfield, T. F.; Osmundsen, P. T.

2009-09-01

On February 22, 1756, approximately 15.7 million cubic meters of bedrock were catastrophically released as a giant rockslide into the Langfjorden. Subsequently, three ˜ 40 meter high tsunami waves overwhelmed the village of Tjelle and several other local communities. Inherited structures had isolated a compartment in the hanging wall damage zone of the fjord-dwelling Tjellefonna fault. Because the region is seismically active in oblique-normal mode, and in accordance with scant historical sources, we speculate that an earthquake on a nearby fault may have caused the already-weakened Tjelle hillside to fail. From interpretation of structural, geomorphic, and thermo-chronological data we suggest that today's escarpment topography of Møre og Trøndelag is controlled to a first order by post-rift reactivation of faults parallel to the Mesozoic passive margin. In turn, a number of these faults reactivated Late Caledonian or early post-Caledonian fabrics. Normal-sense reactivation of inherited structures along much of coastal Norway suggests that a structural link exists between the processes that destroy today's mountains and those that created them. The Paleozoic Møre-Trøndelag Fault Complex was reactivated as a normal fault during the Mesozoic and, probably, throughout the Cenozoic until the present day. Its NE-SW trending strands crop out between the coast and the base of a c. 1.7 km high NW-facing topographic 'Great Escarpment.' Well-preserved kinematic indicators and multiple generations of fault products are exposed along the Tjellefonna fault, a well-defined structural and topographic lineament parallel to both the Langfjorden and the Great Escarpment. The slope instability that was formerly present at Tjelle, and additional instabilities currently present throughout the region, may be viewed as the direct product of past and ongoing development of tectonic topography in Møre og Trøndelag county. In the Langfjorden region in particular, structural geometry suggests additional unreleased rock compartments may be isolated and under normal fault control. Although post-glacial rebound and topographically-derived horizontal spreading stresses might in part help drive present-day oblique normal seismicity, the normal-fault-controlled escarpments of Norway were at least partly erected in pre-glacial times. Cretaceous to Early Tertiary post-rift subsidence was interrupted by normal faulting at the innermost portion of the passive margin, imposing a strong tectonic empreinte on the developing landscape.

Earthquake stress drops, ambient tectonic stresses and stresses that drive plate motions

USGS Publications Warehouse

Hanks, T.C.

1977-01-01

A variety of geophysical observations suggests that the upper portion of the lithosphere, herein referred to as the elastic plate, has long-term material properties and frictional strength significantly greater than the lower lithosphere. If the average frictional stress along the non-ridge margin of the elastic plate is of the order of a kilobar, as suggested by the many observations of the frictional strength of rocks at mid-crustal conditions of pressure and temperature, the only viable mechanism for driving the motion of the elastic plate is a basal shear stress of several tens of bars. Kilobars of tectonic stress are then an ambient, steady condition of the earth's crust and uppermost mantle. The approximate equality of the basal shear stress and the average crustal earthquake stress drop, the localization of strain release for major plate margin earthquakes, and the rough equivalence of plate margin slip rates and gross plate motion rates suggest that the stress drops of major plate margin earthquakes are controlled by the elastic release of the basal shear stress in the vicinity of the plate margin, despite the existence of kilobars of tectonic stress existing across vertical planes parallel to the plate margin. If the stress differences available to be released at the time of faulting are distributed in a random, white fasbion with a mean-square value determined by the average earthquake stress drop, the frequency of occurrence of constant stress drop earthquakes will be proportional to reciprocal faulting area, in accordance with empirically known frequency of occurrence statistics. ?? 1977 Birkha??user Verlag.

A multidisciplinary approach to characterize the geometry of active faults: the example of Mt. Massico, Southern Italy

NASA Astrophysics Data System (ADS)

Luiso, P.; Paoletti, V.; Nappi, R.; La Manna, M.; Cella, F.; Gaudiosi, G.; Fedi, M.; Iorio, M.

2018-06-01

We present the results of a multidisciplinary and multiscale study at Mt. Massico, Southern Italy. Mt. Massico is a carbonate horst located along the Campanian-Latial margin of the Tyrrhenian basin, bordered by two main NE-SW systems of faults, and by NW-SE and N-S trending faults. Our analysis deals with the modelling of the main NE-SW faults. These faults were capable during Plio-Pleistocene and are still active today, even though with scarce and low-energy seismicity (Mw maximum = 4.8). We inferred the pattern of the fault planes through a combined interpretation of 2-D hypocentral sections, a multiscale analysis of gravity field and geochemical data. This allowed us to characterize the geometry of these faults and infer their large depth extent. This region shows very striking gravimetric signatures, well-known Quaternary faults, moderate seismicity and a localized geothermal fluid rise. Thus, this analysis represents a valid case study for testing the effectiveness of a multidisciplinary approach, and employing it in areas with buried and/or silent faults of potential high hazard, such as in the Apennine chain.

A comparison of the South China Sea and Canada Basin: two small marginal ocean basins with hyper-extended margins and central zones of sea-floor spreading.

NASA Astrophysics Data System (ADS)

Li, L.

2015-12-01

Both the South China Sea and Canada Basin preserve oceanic spreading centres and adjacent passive continental margins characterized by broad COT zones with hyper-extended continental crust. We have investigated the nature of strain accommodation in the regions immediately adjacent to the oceanic spreading centres in these two basins using 2-D backstripping subsidence reconstructions, coupled with forward modelling constrained by estimates of upper crustal extensional faulting. Modelling is better constrained in the South China Sea but our results for the Beaufort Sea are analogous. Depth-dependent extension is required to explain the great depth of both basins because only modest upper crustal faulting is observed. A weak lower crust in the presence of high heat flow is suggested for both basins. Extension in the COT may continue even after sea-floor spreading has ceased. The analogous results for the two basins considered are discussed in terms of (1) constraining the timing and distribution of crustal thinning along the respective continental margins, (2) defining the processes leading to hyper-extension of continental crust in the respective tectonic settings and (3) illuminating the processes that control hyper-extension in these basins and more generally.

Utilizing Flight Data to Update Aeroelastic Stability Estimates

NASA Technical Reports Server (NTRS)

Lind, Rick; Brenner, Marty

1997-01-01

Stability analysis of high performance aircraft must account for errors in the system model. A method for computing flutter margins that incorporates flight data has been developed using robust stability theory. This paper considers applying this method to update flutter margins during a post-flight or on-line analysis. Areas of modeling uncertainty that arise when using flight data with this method are investigated. The amount of conservatism in the resulting flutter margins depends on the flight data sets used to update the model. Post-flight updates of flutter margins for an F/A-18 are presented along with a simulation of on-line updates during a flight test.

Kinematic evolution of the southwestern Arabian continental margin: implications for the origin of the Red Sea

NASA Astrophysics Data System (ADS)

Voggenreiter, W.; Hötzl, H.

The tectonic and magnetic evolution of the Jizan coastal plain (Tihama Asir) in southwest Arabia was dominated by SW-NE lithospheric extension related to the development of the Red Sea Rift. A well-exposed, isotopically-dated succession of magmatic rocks (Jizan Group volcanics, Tihama Asir Magmatic Complex) allows a kinematic analysis for this part of the Arabian Red Sea margin. A mafic dyke swarm and several generations of roughly NW-trending normal faults characterized the continental rift stage from Oligocene to early Miocene time. Major uplift of the Arabian graben shoulder probably began about 14 Ma ago. By this time, extension and magmatism ceased in the Jizan area and were followed by an approximately 10 Ma interval of tectonic and magmatic quiescence. A second phase of extension began in the Pliocene and facilitated a vast outpouring of alkaliolivine basalts on the coastal plain. The geometry of faulting in the Jizan area supports a Wernicke-type simple-shear mechanism of continental rifting for the southern Arabian continental margin of the Red Sea.

From magma-poor Ocean Continent Transitions to steady state oceanic spreading: the balance between tectonic and magmatic processes

NASA Astrophysics Data System (ADS)

Gillard, Morgane; Manatschal, Gianreto; Autin, Julia; Decarlis, Alessandro; Sauter, Daniel

2016-04-01

The evolution of magma-poor rifted margins is linked to the development of a transition zone whose basement is neither clearly continental nor oceanic. The development of this Ocean-Continent Transition (OCT) is generally associated to the exhumation of serpentinized mantle along one or several detachment faults. That model is supported by numerous observations (IODP wells, dredges, fossil margins) and by numerical modelling. However, if the initiation of detachment faults in a magma-poor setting tends to be better understood by numerous studies in various area, the transition with the first steady state oceanic crust and the associated processes remain enigmatic and poorly studied. Indeed, this latest stage of evolution appears to be extremely gradual and involves strong interactions between tectonic processes and magmatism. Contrary to the proximal part of the exhumed domain where we can observe magmatic activity linked to the exhumation process (exhumation of gabbros, small amount of basalts above the exhumed mantle), in the most distal part the magmatic system appears to be independent and more active. In particular, we can observe large amounts of extrusive material above a previously exhumed and faulted basement (e.g. Alps, Australia-Antarctica margins). It seems that some faults can play the role of feeder systems for the magma in this area. Magmatic underplating is also important, as suggested by basement uplift and anomalously thick crust (e.g. East Indian margin). It results that the transition with the first steady state oceanic crust is marked by the presence of a hybrid basement, composed by exhumed mantle and magmatic material, whose formation is linked to several tectonic and magmatic events. One could argue that this basement is not clearly different from an oceanic basement. However, we consider that true, steady state oceanic crust only exists, if the entire rock association forming the crust is created during a single event, at a localized spreading center. The interest of that definition is that it does not restrain the term oceanic crust to a basement composition and consequently does not exclude the creation of magma-poor oceanic crust, as observed at slow spreading ridges for example. Indeed, the initiation of steady state oceanic spreading is not necessarily magmatic (e.g. some segments of the Australian-Antarctic margins). In this case, drifting is accommodated by mantle exhumation. However, in this magma-poor transition, and without clear markers of a gradual increase of magmatism, it thus appears difficult to clearly differentiate an exhumed OCT basement and an exhumed oceanic basement. Some theoretical differences can be nevertheless considered: exhumed OCT basement should display a chemical evolution toward the ocean from a subcontinental to an oceanic signature. Moreover, extensional detachment faults are probably long-lived due to the poor influence of the asthenosphere at this stage. On the contrary, exhumed oceanic basement should only display an oceanic signature. In this case, extensional detachment faults are certainly short-lived, due to the strong influence of the asthenosphere, which tends to quickly re-localize the deformation above the spreading center.

Rifting kinematics along the Arabian Margin, Red Sea

NASA Astrophysics Data System (ADS)

Pierantoni, Pietro Paolo; Schettino, Antonio; Zanoni, Davide; Rasul, Najeeb

2017-04-01

The Red Sea represents a young basin floored by oceanic, transitional, or thinned continental crust that formed between Nubia and Arabia. According to most authors, rifting between Nubia and Arabia started in the late Oligocene ( 27 Ma) and it is still in progress in the northern part of the Red Sea at latitudes greater than 24°N. Conversely, the area south of 20.3°N displays a linear spreading ridge extending as south as 14.8°N, which formed in the early Pliocene (the first pulse of sea floor spreading occurred during chron C3n.2n, 4.62 Ma). A transition zone (between 24°N and 20.3°N, present-day coordinates) exists between the northern and the southern sectors, characterized by a segmented spreading center that started forming at 2.58 Ma (chron 2A, late Pliocene) in the southernmost area and propagated northwards. Some authors suggest that the present-day NE-SW spreading directions can be extended back to the early Miocene. However, we are going to show, on the basis of geological evidence from the Arabian margin, that at least two phases of rifting, characterized by distinct extension directions, are necessary to explain the observed structural pattern of deformation in a wide area extending from 28°N to 20°N. At present, there is no magnetic evidence for the existence of a linear spreading center in the northern Red Sea at latitudes higher than 24°N. In this area, the syn-rift pattern of deformation along the Arabian margin is only partly coherent with the present day NE-SW sea floor spreading directions and with the observed trend of fracture zones in the Red Sea. In fact, an older set of rift structures was found during 3 field trips performed along the northern and central Red Sea Arabian margin (2015-2016), suggesting the existence of an earlier rifting stage characterized by N-S trending strike-slip faults and E-W normal faults. The objective of the field trips was to investigate the hypothesis that an early phase of N-S extension and formation of left-lateral pull-apart basins characterized the separation of Arabia from Nubia, as suggested by some authors and by a preliminary analysis of remote sensing data. The necessity of performing structural observations along a wide area along the eastern margin of the northern and central Red Sea led us to select 30 sites where the preliminary morpho-structural analysis of ASTER-GDEM data and geological maps suggested the possibility to study the overprint of younger NE-SW structures on pre-existing N-S strike-slip faults. For each survey site, a number of stations were established to measure kinematic indicators. Most of the mapped structures are E-W and NW-SE normal faults or N-S and NE-SW high-angle strike-slip faults. These different faults belong to the older N-S/E-W system and the younger NW-SE/NE-SW system. Field evidence shows that the second system cuts the first one.

Pore pressure control on faulting behavior in a block-gouge system

NASA Astrophysics Data System (ADS)

Yang, Z.; Juanes, R.

2016-12-01

Pore fluid pressure in a fault zone can be altered by natural processes (e.g., mineral dehydration and thermal pressurization) and industrial operations involving subsurface fluid injection/extraction for the development of energy and water resources. However, the effect of pore pressure change on the stability and slip motion of a preexisting geologic fault remain poorly understood; yet they are critical for the assessment of seismic risk. In this work, we develop a micromechanical model to investigate the effect of pore pressure on faulting behavior. The model couples pore network fluid flow and mechanics of the solid grains. We conceptualize the fault zone as a gouge layer sandwiched between two blocks; the block material is represented by a group of contact-bonded grains and the gouge is composed of unbonded grains. A pore network is extracted from the particulate pack of the block-gouge system with pore body volumes and pore throat conductivities calculated rigorously based on the geometry of the local pore space. Pore fluid exerts pressure force onto the grains, the motion of which is solved using the discrete element method (DEM). The model updates the pore network regularly in response to deformation of the solid matrix. We study the fault stability in the presence of a pressure inhomogeneity (gradient) across the gouge layer, and compare it with the case of homogeneous pore pressure. We consider both normal and thrust faulting scenarios with a focus on the onset of shear failure along the block-gouge interfaces. Numerical simulations show that the slip behavior is characterized by intermittent dynamics, which is evident in the number of slipping contacts at the block-gouge interfaces and the total kinetic energy of the gouge particles. Numerical results also show that, for the case of pressure inhomogeneity, the onset of slip occurs earlier for the side with higher pressure, and that this onset appears to be controlled by the maximum pressure of both sides of the fault. We conclude that the stability of the fault should be evaluated separately for both sides of the gouge layer, a result that sheds new light on the use of the effective stress principle and the Coulomb failure criterion in evaluating the stability of a complex fault zone.

On-Line Robust Modal Stability Prediction using Wavelet Processing

NASA Technical Reports Server (NTRS)

Brenner, Martin J.; Lind, Rick

1998-01-01

Wavelet analysis for filtering and system identification has been used to improve the estimation of aeroservoelastic stability margins. The conservatism of the robust stability margins is reduced with parametric and nonparametric time- frequency analysis of flight data in the model validation process. Nonparametric wavelet processing of data is used to reduce the effects of external disturbances and unmodeled dynamics. Parametric estimates of modal stability are also extracted using the wavelet transform. Computation of robust stability margins for stability boundary prediction depends on uncertainty descriptions derived from the data for model validation. The F-18 High Alpha Research Vehicle aeroservoelastic flight test data demonstrates improved robust stability prediction by extension of the stability boundary beyond the flight regime. Guidelines and computation times are presented to show the efficiency and practical aspects of these procedures for on-line implementation. Feasibility of the method is shown for processing flight data from time- varying nonstationary test points.

Multi-phase inversion tectonics related to the Hendijan-Nowrooz-Khafji Fault activity, Zagros Mountains, SW Iran

NASA Astrophysics Data System (ADS)

Kazem Shiroodi, Sadjad; Ghafoori, Mohammad; Faghih, Ali; Ghanadian, Mostafa; Lashkaripour, Gholamreza; Hafezi Moghadas, Naser

2015-11-01

Distinctive characteristics of inverted structures make them important criteria for the identification of certain structural styles of folded belts. The interpretation of 3D seismic reflection and well data sheds new light on the structural evolution and age of inverted structures associated to the Hendijan-Nowrooz-Khafji Fault within the Persian Gulf Basin and northeastern margin of Afro-Arabian plate. Analysis of thickness variations of growth strata using "T-Z plot" (thickness versus throw plot) method revealed the kinematics of the fault. Obtained results show that the fault has experienced a multi-phase evolutionary history over six different extension and compression deformation events (i.e. positive and negative inversion) between 252.2 and 11.62 Ma. This cyclic activity of the growth fault was resulted from alteration of sedimentary processes during continuous fault slip. The structural development of the study area both during positive and negative inversion geometry styles was ultimately controlled by the relative motion between the Afro-Arabian and Central-Iranian plates.

Early Neogene unroofing of the Sierra Nevada de Santa Marta along the Bucaramanga -Santa Marta Fault

NASA Astrophysics Data System (ADS)

Piraquive Bermúdez, Alejandro; Pinzón, Edna; Bernet, Matthias; Kammer, Andreas; Von Quadt, Albrecht; Sarmiento, Gustavo

2016-04-01

Plate interaction between Caribbean and Nazca plates with Southamerica gave rise to an intricate pattern of tectonic blocks in the Northandean realm. Among these microblocks the Sierra Nevada de Santa Marta (SNSM) represents a fault-bounded triangular massif composed of a representative crustal section of the Northandean margin, in which a Precambrian to Late Paleozoic metamorphic belt is overlain by a Triassic to Jurassic magmatic arc and collateral volcanic suites. Its western border fault belongs to the composite Bucaramanga - Santa Marta fault with a combined left lateral-normal displacement. SE of Santa Marta it exposes remnants of an Oligocene marginal basin, which attests to a first Cenoizoic activation of this crustal-scale lineament. The basin fill consists of a sequence of coarse-grained cobble-pebble conglomerates > 1000 m thick that unconformably overlay the Triassic-Jurassic magmatic arc. Its lower sequence is composed of interbedded siltstones; topwards the sequence becomes dominated by coarser fractions. These sedimentary sequences yields valuable information about exhumation and coeval sedimentation processes that affected the massif's western border since the Upper Eocene. In order to analyse uplifting processes associated with tectonics during early Neogene we performed detrital zircon U-Pb geochronology, detrital thermochronology of zircon and apatites coupled with the description of a stratigraphic section and its facies composition. We compared samples from the Aracataca basin with analog sequences found at an equivalent basin at the Oca Fault at the northern margin of the SNSM. Our results show that sediments of both basins were sourced from Precambrian gneisses, along with Mesozoic acid to intermediate plutons; sedimentation started in the Upper Eocene-Oligocene according to palynomorphs, subsequently in the Upper Oligocene a completion of Jurassic to Cretaceous sources was followed by an increase of Precambrian input that became the dominant source for sediments, this shift in provenance is related to an increase in exhumation and erosion rates. The instauration of such a highly erosive regime since the Upper Oligocene attests how the Santa Marta massif was subject to uplifting and erosion, our data shows how in the Upper Oligocene an exhaustion of Cretaceous to Permian sources was followed by an increase in Neo-Proterozoic to Meso-Proterozoic input that is related to the unroofing of the basement rocks, this accelerated exhumation is directly related to the reactivation of the Orihueca Fault as a NW verging thrust at the interior of the massif coeval with Bucaramanga-Santa Marta Fault trans-tensional tectonics in response to the fragmentation of the Farallon plate into the Nazca an Cocos Plates.

The Sedimentary History of Southern Central Crete: Implications for Neogene Uplift

NASA Astrophysics Data System (ADS)

Kröger, K.; Brachert, T. C.; Reuter, M.

2003-04-01

The tectonic setting of Crete was largely extensional since Lower Miocene uplift and exhumation of HP/LT rocks. Erosion of uplifted areas resulted in the deposition of terrestrial to marine sediments in the Messara and Iraclion Basins. There are several concurring models that discuss Late Neogene uplift of the basinal margins. Neogene near shore sediments in the south of the Messara Basin record fault movements contemporaneous to sedimentation and sedimentary input from the hinterland. Therefore they provide information on the paleogeographic situation and the resulting amount of subsidence and uplift of mountain areas since the Upper Miocene. The studied sediments consist of terrestrial to shallow marine, floodplain related sediments of the Upper Miocene Ambelouzos Formation that are overlain by platform limestones of the Upper Miocene Varvara Formation. In the Messara Basin these units are overlain by the Pliocene Kourtes Formation. The stratigraphic architecture of these deposits indicates fragmentation of the basinal margin. Proximal boulder conglomerates and reworked blocks of the Ambelouzos formation indicate fault activity during the deposition of the Varvara Formation. Contents of terrigenous clastics, provided by rivers and distributed by longshore currents, are high in the Ambelouzos and the lower Varvara Formations but decrease rapidly upsection within the Varvara Formation. This indicates drowning of the fault bounded blocks and little topography of the hinterland (Asteroussia Mountains) at that time. The Pliocene marls at the southern margin of the Messara Basin contain lithoclasts of the Upper Miocene limestones and thus indicate uplift of the carbonate platform. The modern topographic elevation of formerly drowned fault bounded blocks requires a minimum uplift of 400m. Main uplift occurred at approximately orthogonal NW-SE and SW-NE striking normal to oblique faults. The present elevation of the Asteroussia Mountains indicates net uplift of at least 1000m since the Early Pliocene. At the Central Iraklion Ridge that separates the Messara and Iraclion Basins a similar history is indicated for the Psiloritis Mountains by fault movements within Neogene near shore sediments and their subsequent drowning. A structural model of the Neogene evolution of Crete therefore has to explain successive phases of uplift and subsidence in an over all extensional setting only slightly oblique to the modern direction of convergence between Africa and the Aegean microplate.

Upper plate contraction north of the migrating Mendocino triple junction northern California: Implications for partitioning of strain

USGS Publications Warehouse

McCrory, P.A.

2000-01-01

Geologic measurement of permanent contraction across the Cascadia subduction margin constrains one component of the tectonic deformation along the convergent plate boundary, the component critical for the seismic hazard assessment of crustal faults. A comprehensive survey of active faults in onshore subduction margin rocks at the southern end of the Cascadia subduction zone indicates that these thrust faults accommodate ??10 mm/yr of convergence oriented 020??-045??. Seismotectonic models of subduction zones typically assign this upper plate strain to the estimate of aseismic slip on the megathrust. Geodetic models include this permanent crustal strain within estimates of elastic strain accumulation on the megathrust. Both types of models underestimate the seismic hazard associated with crustal faults. Subtracting the observed contraction from the plate convergence rate (40-50 mm/yr; directed 040??-055??) leaves 30-40 mm/yr of convergence to be partitioned between slip on the megathrust, contraction within the southern Juan de Fuca plate, and crustal contraction outside the subduction complex rocks. This simple estimate of slip partitioning neglects the discrepancy between the plate convergence and contraction directions in the vicinity of the Mendocino triple junction. The San Andreas and Cascadia limbs of the Mendocino triple junction are not collinear. The eastern edge of the broad San Andreas boundary is ??85 km east of the Cascadia subduction boundary, and across this zone the Pacific plate converges directly with the North America plate. The skewed orientation of crustal structures just north of the leading edge of the Pacific plate suggests that they are deforming in a hybrid stress field resulting from both Juan de Fuca-North America motion and Pacific-North America motion. The composite convergence direction (50 mm/yr: directed 023??) is consistent with the compressive stress axis (020??) inferred from focal mechanisms of crustal earthquakes in the Humboldt region. Deformation in such a hybrid stress field implies that the crustal faults are being loaded from two major tectonic sources. The slip on crustal faults north of the Mendocino triple junction may consume 4-5 mm/yr of Pacific-Humboldt convergence. The remaining 17-18 mm/yr of convergence may be consumed as distributed shortening expressed in the high rates of uplift in the Cape Mendocino region or as northward translation of the continental margin, north of the triple junction.

Moment tensor solutions for the Iberian-Maghreb region during the IberArray deployment (2009-2013)

NASA Astrophysics Data System (ADS)

Martín, R.; Stich, D.; Morales, J.; Mancilla, F.

2015-11-01

We perform regional moment tensor inversion for 84 earthquakes that occurred in the Iberian-Maghreb region during the second and third leg of IberArray deployment (2009-2013). During this period around 300 seismic broadband stations were operating in the area, reducing the interstation spacing to ~ 50 km over extended areas. We use the established processing sequence of the IAG moment tensor catalogue, increasing to 309 solutions with this update. New moment tensor solutions present magnitudes ranging from Mw 3.2 to 6.3 and source depths from 2 to 620 km. Most solutions correspond to Northern Algeria, where a compressive deformation pattern is consolidated. The Betic-Rif sector shows a progression of faulting styles from mainly shear faulting in the east via predominantly extension in the central sector to reverse and strike-slip faulting in the west. At the SW Iberia margin, the predominance of strike-slip and reverse faulting agrees with the expected transpressive character of the Eurasian-Nubia plate boundary. New strike-slip and oblique reverse solutions in the Trans-Alboran Shear Zone reflect its left-lateral regime. The most significant improvement corresponds to the Atlas Mountains and the surroundings of the Gibraltar Arc with scarce previous solutions. Reverse and strike-slip faulting solutions in the Atlas System display the accommodation of plate convergence by shortening in the belt. At the Gibraltar Arc, several new solutions were obtained at lower crustal and subcrustal depths. These mechanisms show substantial heterogeneity, covering the full range of faulting styles with highly variable orientations of principal stress axes, including opposite strike slip faulting solutions at short distance. The observations are not straightforward to explain by a simple geodynamic scenario and suggest the interplay of different processes, among them plate convergence in old oceanic lithospheric with large brittle thickness at the SW Iberia margin, as well as delamination of thickened continental lithosphere beneath the Betic-Rif arc.

Seismic Investigations of an Accommodation zone in the Northern Rio Grande Rift, New Mexico, USA

NASA Astrophysics Data System (ADS)

Baldridge, W. S.; Valdes, J.; Nedorub, O.; Phrampus, B.; Braile, L. W.; Ferguson, J. F.; Benage, M. C.; Litherland, M.

2010-12-01

Seismic reflection and refraction data acquired in the Rio Grande rift near Santa Fe, New Mexico, in 2009 and 2010 by the SAGE (Summer of Applied Geophysical Experience) program imaged the La Bajada fault (LBF) and strata offset across the associated, perpendicular Budagher fault (BF). The LBF is a major basin-bounding normal fault, offset down to the west; the smaller BF is an extensional fault that breaks the hanging wall ramp of the LBF. We chose this area because it is in a structurally complex region of the rift, comprising a small sub-basin and plunging relay ramps, where north-trending, en echelon basin-bounding faults (including the LBF) transfer crustal extension laterally between the larger Española (to north) and Albuquerque rift basins. Our data help determine the precise location and geometry of the poorly exposed LBF, which, near the survey location, offsets the rift margin vertically about 3,000 m. When integrated with industry reflection data and other SAGE seismic, gravity, and magnetotelluric surveys, we are able to map differences in offset and extension laterally (especially southward) along the fault. We interpret only about 200 m of normal offset across the BF. Our continuing work helps define multiple structural elements, partly buried by syn-rift basin-filling sedimentary rocks, of a complex intra-rift accommodation zone. We are also able to discriminate pre-Eocene (Laramide) from post-Miocene (rift) structures. Our data help determine the amount of vertical offset of pre-rift strata across structural elements of the accommodation zone, and depth and geometry of basin fill. A goal is to infer the kinematic development of this margin of the rift, linkages among faults, growth history, and possible pre-rift structural controls. This information will be potentially useful for evaluation of resources, including oil and/or gas in pre-rift strata and ground water in Late Miocene to Holocene rift-filling units.

Growth and gravitational collapse of a mountain front of the Eastern Cordillera of Colombia

NASA Astrophysics Data System (ADS)

Kammer, Andreas; Montana, Jorge; Piraquive, Alejandro

2016-04-01

The Eastern Cordillera of Colombia is bracketed between the moderately east-dipping flank of the Central Cordillera on its western and the gently bent Guayana shield on its eastern side. It evolved as a response to a considerable displacement transfer from the Nazca to the Southamerican plate since the Oligocene break-up of the Farallon plate. One of its distinctive traits refers to its significant shortening by penetrative strain at lower and folding at higher structural levels, approximating a wholesale pure-shear in analogy to a vice model or a crustal welt sandwiched between rigid buttresses. This contrasting behavior may be explained by the spatial coincidence between Neogene mountain belt and a forebulge that shaped the foreland trough during a Cretaceous subduction cycle and was very effective in localizing a weakening of the backarc region comprised between two basin margin faults. In this paper we examine a two-phase evolution of the Eastern mountain front. Up to the late Miocene deformation was restrained by the inherited eastern basin margin fault and as the cordilleran crust extruded, a deformation front with an amplitude similar the present structural relief of up to 10.000 m may have built up. In the Pliocene convergence changed from a roughly strike-perpendicular to an oblique E-W direction and caused N-S trending faults to branch off from the deformation front. This shortening was partly driven by a gravitational collapse of the Miocene deformation front, that became fragmented by normal faults and extruded E on newly formed Pliocene thrust faults. Normal faults display displacements of up to 3000 m and channelized hydrothermal fluids, leading to the formation of widely distributed fault breccias and giving rise to a prolific Emerald mineralization. In terms of wedge dynamics, the Pliocene breaching of the early formed deformation front helped to establish a critical taper.

The tectonic evolution of the southeastern Terceira Rift/São Miguel region (Azores)

NASA Astrophysics Data System (ADS)

Weiß, B. J.; Hübscher, C.; Lüdmann, T.

2015-07-01

The eastern Azores Archipelago with São Miguel being the dominant subaerial structure is located at the intersection of an oceanic rift (Terceira Rift) with a major transform fault (Gloria Fault) representing the westernmost part of the Nubian-Eurasian plate boundary. The evolution of islands, bathymetric highs and basin margins involves strong volcanism, but the controlling geodynamic and tectonic processes are currently under debate. In order to study this evolution, multibeam bathymetry and marine seismic reflection data were collected to image faults and stratigraphy. The basins of the southeastern Terceira Rift are rift valleys whose southwestern and northeastern margins are defined by few major normal faults and several minor normal faults, respectively. Since São Miguel in between the rift valleys shows an unusual W-E orientation, it is supposed to be located on a leaky transform. South of the island and separated by a N120° trending graben system, the Monacco Bank represents a N160° oriented flat topped volcanic ridge dominated by tilted fault blocks. Up to six seismic units are interpreted for each basin. Although volcanic ridges hamper a direct linking of depositional strata between the rift and adjacent basins, the individual seismic stratigraphic units have distinct characteristics. Using these units to provide a consistent relative chrono-stratigraphic scheme for the entire study area, we suggest that the evolution of the southeastern Terceira Rift occurred in two stages. Considering age constrains from previous studies, we conclude that N140° structures developed orthogonal to the SW-NE direction of plate-tectonic extension before ~ 10 Ma. The N160° trending volcanic ridges and faults developed later as the plate tectonic spreading direction changed to WSW-ENE. Hence, the evolution of the southeastern Terceira Rift domain is predominantly controlled by plate kinematics and lithospheric stress forming a kind of a re-organized rift system.

An experimental study of the influence of stress history on fault slip during injection of supercritical CO2

NASA Astrophysics Data System (ADS)

Cuss, Robert J.; Wiseall, Andrew C.; Tamayo-Mas, Elena; Harrington, Jon F.

2018-04-01

The injection of super-critical CO2 into a depleted reservoir will alter the pore pressure of the basin, which if sufficiently perturbed could result in fault slip. Therefore, knowledge of the acceptable pressure limits is required in order to maintain fault stability. A two-part laboratory study was conducted on fully saturated kaolinite fault gouge to investigate this issue. Previously, we showed that fault slip occurred once pore-pressure within the gouge was sufficient to overcome the normal stress acting on the fault. For kaolinite, this behaviour occurred at a pressure similar to the yield stress. The current study shows that following a slow-reduction in the maximum principal stress, as would be expected through changes in effective stress, the reactivation pressure shows a stress memory. Consequently, the pressure necessary to initiate fault slip is similar to that required at the maximum stress encountered. Therefore, fault slip is at least partially controlled by the previous maximum stress and not the current stress state. During the slow reduction in normal stress, the flow characteristics of the fault remain unchanged until pore-pressure exceeds shear stress and does not increase significantly until it exceeds normal stress. This results in fault slip, which slows the rate of flow increase as shear is an effective self-sealing mechanism. These observations lead to the conclusion that stress history is a vital parameter when considering fault stability.

Basement control of structure in the Gettysburg rift basin, Pennsylvania and Maryland

NASA Astrophysics Data System (ADS)

Root, Samuel I.

1989-09-01

Jurassic faulting formed the 93 km long Gettysburg basin as an extensional half graben paralleling the basement structural grain. Preserved in the basin are rift-related Carnian to Rhaetian strata that were tilted 20-30° NW into a SE dipping, listric normal fault at the northwest border of the basin. Vertical displacement on the border fault approaches 10 km. The border fault developed parallel to the trend of the terminal Paleozoic Alleghenian South Mountain cleavage of the Blue Ridge basement along 80% of its extent. However, it is only roughly parallel to discordant to dip of the cleavage. Relationship of cleavage and later border faulting may be the result of persistent reactivation of the original Appalachian continental margin. Local complex structures in the half graben are related to reactivation of two subvertical, pre-Mesozoic faults that transect basement structural grain (cleavage) at a large angle. The northern Shippensburg fault was reactivated during basin normal faulting, offsetting the border fault in a right-lateral sense by 3.5 km and forming within the basin a fold and a fault sliver of basement. The southern Carbaugh-Marsh Creek fault was not reactivated, but is the locus of a 20°-30° change of trend of both the basement cleavage and later border fault. However, two large, NW trending, left-lateral wrench faults, antithetic to the Carbaugh-March Creek fault, developed here offsetting the border fault and forming en echelon folds and horst blocks of basement rock within the basin.

Structural style and tectonic evolution of the easternmost Gulf of Aden conjugate margins (Socotra - Southern Oman)

NASA Astrophysics Data System (ADS)

Nonn, Chloe; Leroy, Sylvie; Castilla, Raymi; de Clarens, Philippe; Lescanne, Marc

2016-04-01

Observations from distal rifted margins in present day magma-poor rifted margins led to the discovery of hyperextended crust and exhumed sub-continental mantle. This finding allowed to better figure out how thinning process are accommodate by tectonic structures, forming various crustal domains, as the deformation localized towards the future area of breakup. However, some of the current challenges are about clarifying how factors as oblique kinematic, pre-existing structures and volcanism can control the 3D geometry and crustal architecture of the passive margins? A key to better understand the rifting evolution in its entirety is to study conjugate margins. The gulf of Aden is a young oceanic basin (with a global trend about N75°E) oblique to the divergence (about 30°N), separating Arabia from Somalia of less than 800 km. Thanks to its immerged margins and its thin post-rift sediment cover, the gulf of Aden basin is a natural laboratory to investigate conjugate margins and strain localisation throughout the rift history. In this contribution, we focus our interest on offshore Socotra Island (Yemen) and its conjugate in Southeastern Oman. This area extends from Socotra-Hadbeen (SHFZ) and the eastern Gulf of Aden fault zones (EGAFZ). In the easternmost part of the gulf of Aden, we provide new insights into crustal deformation and emplacement of the new oceanic crust thanks to bathymetric, magnetic, gravimetric data and single-, multi-channel, high speed seismic reflection data collected during Encens-Sheba (2000), Encens (2006) and the more recent Marges-Aden (2012) cruises respectively. The results obtained after compilation of these data, previous geological (field works) and geophysical (receiver functions, Pn-tomography, magnetic anomalies, heat flow) studies on the focused area, allowed us to provide new structural mapping and stratigraphic correlation between onshore and offshore parts of Socotra and Oman margins. We precisely defined and map crustal domains, syn-tectonic structures and oblique accommodation zones to highlighted asymmetrical margins, characterized by strong lateral variability of crustal domains along and across strike. From external to internal domains of the margins and in between SHFZ and EGAFZ (first-order segment), this study details sharp necking domain and complex transition from hyperextended to oceanic crust characterized by: (i) hyperextended crust affected by volcanic extrusions; (ii) detachment faulting in the distal part of the margins allowing exhumation; (iii) volcanic constructions in the exhumation domain; (iv) a complex proto-oceanic crust. We highlight a significant second-order segmentation characterized by six N20°E trending transfer zones, limiting seven 25 - 60 km length segments and affecting necking domain as well as the ocean-continent transition. Based on interpretative cross-sections and detailed stratigraphic analysis, we discuss the complex temporal and spatial evolution of conjugate margins: (i) the margins segmentation and the relationship with structural inheritance (ii) the set-up of a long-offset detachment fault and the nature of the exhumed basement (iv) the origin and timing of magmatic events and the onset of proto-oceanic crust.

Optimization of Second Fault Detection Thresholds to Maximize Mission POS

NASA Technical Reports Server (NTRS)

Anzalone, Evan

2018-01-01

In order to support manned spaceflight safety requirements, the Space Launch System (SLS) has defined program-level requirements for key systems to ensure successful operation under single fault conditions. To accommodate this with regards to Navigation, the SLS utilizes an internally redundant Inertial Navigation System (INS) with built-in capability to detect, isolate, and recover from first failure conditions and still maintain adherence to performance requirements. The unit utilizes multiple hardware- and software-level techniques to enable detection, isolation, and recovery from these events in terms of its built-in Fault Detection, Isolation, and Recovery (FDIR) algorithms. Successful operation is defined in terms of sufficient navigation accuracy at insertion while operating under worst case single sensor outages (gyroscope and accelerometer faults at launch). In addition to first fault detection and recovery, the SLS program has also levied requirements relating to the capability of the INS to detect a second fault, tracking any unacceptable uncertainty in knowledge of the vehicle's state. This detection functionality is required in order to feed abort analysis and ensure crew safety. Increases in navigation state error and sensor faults can drive the vehicle outside of its operational as-designed environments and outside of its performance envelope causing loss of mission, or worse, loss of crew. The criteria for operation under second faults allows for a larger set of achievable missions in terms of potential fault conditions, due to the INS operating at the edge of its capability. As this performance is defined and controlled at the vehicle level, it allows for the use of system level margins to increase probability of mission success on the operational edges of the design space. Due to the implications of the vehicle response to abort conditions (such as a potentially failed INS), it is important to consider a wide range of failure scenarios in terms of both magnitude and time. As such, the Navigation team is taking advantage of the INS's capability to schedule and change fault detection thresholds in flight. These values are optimized along a nominal trajectory in order to maximize probability of mission success, and reducing the probability of false positives (defined as when the INS would report a second fault condition resulting in loss of mission, but the vehicle would still meet insertion requirements within system-level margins). This paper will describe an optimization approach using Genetic Algorithms to tune the threshold parameters to maximize vehicle resilience to second fault events as a function of potential fault magnitude and time of fault over an ascent mission profile. The analysis approach, and performance assessment of the results will be presented to demonstrate the applicability of this process to second fault detection to maximize mission probability of success.

Effects of nuclear electromagnetic pulse (EMP) on synchronous stability of the electric power system

DOE Office of Scientific and Technical Information (OSTI.GOV)

Manweiler, R.W.

1975-11-01

The effects of a nuclear electromagnetic pulse (EMP) on the synchronous stability of the electric power transmission and distribution systems are evaluated. The various modes of coupling of EMP to the power system are briefly discussed, with particular emphasis on those perturbations affecting the synchronous stability of the transmission system. A brief review of the fundamental concepts of the stability problem is given, with a discussion of the general characteristics of transient analysis. A model is developed to represent single sets as well as repetitive sets of multiple faults on the distribution systems, as might be produced by EMP. Themore » results of many numerical stability calculations are presented to illustrate the transmission system's response from different types of perturbations. The important parameters of both multiple and repetitive faults are studied, including the dependence of the response on the size of the perturbed area, the fault density, and the effective impedance between the fault location and the transmission system. Both major load reduction and the effect of the opening of tie lines at the time of perturbation are also studied. We conclude that there is a high probability that EMP can induce perturbations on the distribution networks causing a large portion of the transmission network in the perturbed area to lose synchronism. The result would be an immediate and massive power failure. (auth)« less

Fortnightly modulation of San Andreas tremor and low-frequency earthquakes

USGS Publications Warehouse

Van Der Elst, Nicholas; Delorey, Andrew; Shelly, David R.; Johnson, Paul

2016-01-01

Earth tides modulate tremor and low-frequency earthquakes (LFEs) on faults in the vicinity of the brittle−ductile (seismic−aseismic) transition. The response to the tidal stress carries otherwise inaccessible information about fault strength and rheology. Here, we analyze the LFE response to the fortnightly tide, which modulates the amplitude of the daily tidal stress over a 14-d cycle. LFE rate is highest during the waxing fortnightly tide, with LFEs most strongly promoted when the daily stress exceeds the previous peak stress by the widest margin. This pattern implies a threshold failure process, with slip initiated when stress exceeds the local fault strength. Variations in sensitivity to the fortnightly modulation may reflect the degree of stress concentration on LFE-producing brittle asperities embedded within an otherwise aseismic fault.

Identification of hyper-extended crust east of Davie Ridge in the Mozambique Channel

NASA Astrophysics Data System (ADS)

Klimke, Jennifer; Franke, Dieter

2015-04-01

Davie Ridge is a ~1200 km wide, N-S trending bathymetrical high in the Mozambique Channel. Today, it is widely accepted that Davie Ridge is located along a fossil transform fault that was active during the Middle Jurassic and Early Cretaceous (~165-120 Ma). This transform fault results from the breakup of Gondwana, when Madagascar (together with India and Antarctica) drifted from its northerly position in the Gondwana Supercontinent (adjacent to the coasts of Tanzania, Somalia and Kenya) to its present position (e.g. Coffin and Rabinowitz, 1987; Rabinowitz et al., 1983; Segoufin and Patriat, 1980). The southward motion of Madagascar relative to Africa is constrained by the interpretation of magnetic anomalies in the Western Somali Basin, located north of Madagascar (e.g. Rabinowitz et al., 1983). According to Bird (2001), sheared margins share typical characteristics and a common evolution: 1. The transition from continental to oceanic crust is relatively abrupt (~ 50-80 km). 2. Along the continental side of the margin, complex rift basins form that display a wide range of faults. 3. Prominent marginal ridges form along the sheared margin that probably originate from the propagation of the oceanic spreading center along the plate boundary (Bird, 2001). In February and March 2014, a dense geophysical dataset (multichannel seismic, magnetics, gravimetry and bathymetry) with a total of 4300 profile km along the sheared margin was acquired with the R/V Sonne by the Federal Institute for Geosciences and Natural Resources (BGR). A special objective of the project, amongst others, is the characterization and interpretation of the continent-ocean transition seaward of Davie Ridge in the Mozambique Channel. Seismic profiles located east of Davie Ridge in the Western Somali Basin reveal a wide sequence of half-grabens bounded by listric normal faults. We tentatively suggest that this crust is of continental origin and results from rifting between Africa and Madagascar during the breakup of Gondwana. This implies that the continent-ocean transition is located at least ~ 150 km east of Davie Ridge. References Bird, D., 2001. Shear margins: Continent-ocean transform and fracture zone boundaries. The Leading Edge, 150-159. Coffin, M. F., und Rabinowitz, P. D., 1987. Reconstruction of Madagascar and Africa: Evidence from the Davie Fracture Zone and Western Somali Basin. Journal of Geophysical Research: Solid Earth, vol. 92, no. B9, 9385-9406. Rabinowitz, P.D., Coffin, M.F. and Falvey, D.A., 1983. The separation of Madagascar and Africa. Science 220, 67-69. Segoufin, J., und Patriat, P., 1980. Existence d'anomalies mesozoiques dans le bassin de Somalie. Implications pour les relations Afrique-Antarctique-Madagascar: C.R. Acad. Sci. Paris, v. 291, p. 85-88.

Interactions between Polygonal Normal Faults and Larger Normal Faults, Offshore Nova Scotia, Canada

NASA Astrophysics Data System (ADS)

Pham, T. Q. H.; Withjack, M. O.; Hanafi, B. R.

2017-12-01

Polygonal faults, small normal faults with polygonal arrangements that form in fine-grained sedimentary rocks, can influence ground-water flow and hydrocarbon migration. Using well and 3D seismic-reflection data, we have examined the interactions between polygonal faults and larger normal faults on the passive margin of offshore Nova Scotia, Canada. The larger normal faults strike approximately E-W to NE-SW. Growth strata indicate that the larger normal faults were active in the Late Cretaceous (i.e., during the deposition of the Wyandot Formation) and during the Cenozoic. The polygonal faults were also active during the Cenozoic because they affect the top of the Wyandot Formation, a fine-grained carbonate sedimentary rock, and the overlying Cenozoic strata. Thus, the larger normal faults and the polygonal faults were both active during the Cenozoic. The polygonal faults far from the larger normal faults have a wide range of orientations. Near the larger normal faults, however, most polygonal faults have preferred orientations, either striking parallel or perpendicular to the larger normal faults. Some polygonal faults nucleated at the tip of a larger normal fault, propagated outward, and linked with a second larger normal fault. The strike of these polygonal faults changed as they propagated outward, ranging from parallel to the strike of the original larger normal fault to orthogonal to the strike of the second larger normal fault. These polygonal faults hard-linked the larger normal faults at and above the level of the Wyandot Formation but not below it. We argue that the larger normal faults created stress-enhancement and stress-reorientation zones for the polygonal faults. Numerous small, polygonal faults formed in the stress-enhancement zones near the tips of larger normal faults. Stress-reorientation zones surrounded the larger normal faults far from their tips. Fewer polygonal faults are present in these zones, and, more importantly, most polygonal faults in these zones were either parallel or perpendicular to the larger faults.

Preliminary potential-field constraints on the geometry of the San Fernando basin, Southern California

USGS Publications Warehouse

Langenheim, V.E.; Griscom, Andrew; Jachens, R.C.; Hildenbrand, T.G.

2000-01-01

Gravity and magnetic data provide new insights on the structural underpinnings of the San Fernando Basin region, which may be important to ground motion models. Gravity data indicate that a deep basin (>5 km) underlies the northern part of the San Fernando Valley; this deep basin is required to explain the lowest gravity values over the Mission Hills thrust fault. Gravity modeling, constrained by well data and density information, shows that the basin may reach a thickness of 8 km, coinciding with the upper termination of the 1994 Northridge earthquake mainshock rupture. The basin is deeper than previous estimates by 2 to 4 km; this estimate is the result of high densities for the gravels of the Pliocene-Pleisocene Saugus Formation. The geometry of the southern margin of the deep basin is not well-constrained by the gravity data, but may dip to the south. Recently acquired seismic data along the LARSE (Los Angeles Regional Seismic Experiment) II profile may provide constraints to determine the location and attitude of the basin edge. Gravity and aeromagnetic models across the eastern margin of the San Fernando Valley indicate that the Verdugo fault may dip to the southwest along its southern extent and therefore have a normal fault geometry whereas it clearly has a thrust fault geometry along its northern strand.

High resolution seismic-reflection imaging of shallow deformation beneath the northeast margin of the Manila high at Big Lake, Arkansas

USGS Publications Warehouse

Odum, J.K.; Stephenson, W.J.; Williams, R.A.; Worley, D.M.; Guccione, M.J.; Van Arsdale, R.B.

2001-01-01

The Manila high, an elliptical area 19 km long (N-S) by 6 km wide (E-W) located west-southwest of Big Lake. Arkansas, has less than 3 m of topographic relief. Geomorphic, stratigraphic and chronology data indicate that Big Lake formed during at least two periods of Holocene uplift and subsequent damming of the south-flowing Little River. Age data of an organic mat located at the base of an upper lacustrine deposit indicates an abrupt, possibly tectonic, formation of the present Big Lake between AD 1640 and 1950. We acquired 7 km of high-resolution seismic-reflection data across the northeastern margin of the Manila high to examine its near-surface bedrock structure and possible association with underlying structures such as the Blytheville arch. Sense of displacement and character of imaged faults support interpretations for either a northwest trending, 1.5 km-wide, block of uplifted strata or a series of parallel northeast-trending faults that bound horst and graben structures. We interpret deformation of the Manila high to result from faulting generated by the reactivation of right-lateral strike-slip fault motion along this portion of the Blytheville arch. The most recent uplift of the Manila high may have occurred during the December 16, 1811, New Madrid earthquake. Published by Elsevier Science B.V.

Fault-tolerant conversion between adjacent Reed-Muller quantum codes based on gauge fixing

NASA Astrophysics Data System (ADS)

Quan, Dong-Xiao; Zhu, Li-Li; Pei, Chang-Xing; Sanders, Barry C.

2018-03-01

We design forward and backward fault-tolerant conversion circuits, which convert between the Steane code and the 15-qubit Reed-Muller quantum code so as to provide a universal transversal gate set. In our method, only seven out of a total 14 code stabilizers need to be measured, and we further enhance the circuit by simplifying some stabilizers; thus, we need only to measure eight weight-4 stabilizers for one round of forward conversion and seven weight-4 stabilizers for one round of backward conversion. For conversion, we treat random single-qubit errors and their influence on syndromes of gauge operators, and our novel single-step process enables more efficient fault-tolerant conversion between these two codes. We make our method quite general by showing how to convert between any two adjacent Reed-Muller quantum codes \\overline{\\textsf{RM}}(1,m) and \\overline{\\textsf{RM}}≤ft(1,m+1\\right) , for which we need only measure stabilizers whose number scales linearly with m rather than exponentially with m obtained in previous work. We provide the explicit mathematical expression for the necessary stabilizers and the concomitant resources required.

Fluid expulsion sites on the Cascadia accretionary prism: mapping diagenetic deposits with processed GLORIA imagery

USGS Publications Warehouse

Carson, Bobb; Seke, Erol; Paskevich, Valerie F.; Holmes, Mark L.

1994-01-01

Point-discharge fluid expulsion on accretionary prisms is commonly indicated by diagenetic deposition of calcium carbonate cements and gas hydrates in near-surface (<10 m below seafloor; mbsf) hemipelagic sediment. The contrasting clastic and diagenetic lithologies should be apparent in side scan images. However, sonar also responds to variations in bottom slope, so unprocessed images mix topographic and lithologic information. We have processed GLORIA imagery from the Oregon continental margin to remove topographic effects. A synthetic side scan image was created initially from Sea Beam bathymetric data and then was subtracted iteratively from the original GLORIA data until topographic features disappeared. The residual image contains high-amplitude backscattering that we attribute to diagenetic deposits associated with fluid discharge, based on submersible mapping, Ocean Drilling Program drilling, and collected samples. Diagenetic deposits are concentrated (1) near an out-of-sequence thrust fault on the second ridge landward of the base of the continental slope, (2) along zones characterized by deep-seated strikeslip faults that cut transversely across the margin, and (3) in undeformed Cascadia Basin deposits which overlie incipient thrust faults seaward of the toe of the prism. There is no evidence of diagenetic deposition associated with the frontal thrust that rises from the dècollement. If the dècollement is an important aquifer, apparently the fluids are passed either to the strike-slip faults which intersect the dècollement or to the incipient faults in Cascadia Basin for expulsion. Diagenetic deposits seaward of the prism toe probably consist dominantly of gas hydrates.

Hydrothermal minerals and microstructures in the Silangkitang geothermal field along the Great Sumatran fault zone, Sumatra, Indonesia

USGS Publications Warehouse

Moore, Diane E.; Hickman, S.; Lockner, D.A.; Dobson, P.F.

2001-01-01

Detailed study of core samples of silicic tuff recovered from three geothermal wells along the strike-slip Great Sumatran fault zone near Silangkitang, North Sumatra, supports a model for enhanced hydrothermal circulation adjacent to this major plate-boundary fault. Two wells (A and C) were drilled nearly vertically ??1 km southwest of the eastern (i.e., the principal) fault trace, and the third, directional well (B) was drilled eastward from the site of well A to within ??100 m of the principal fault trace. The examined core samples come from depths of 1650-2120 m at measured well temperatures of 180-320 ??C. The samples collected near the principal fault trace have the highest temperatures, the largest amount of secondary pore space that correlates with high secondary permeability, and the most extensive hydrothermal mineral development. Secondary permeability and the degree of hydrothermal alteration decrease toward the southwestern margin of the fault zone. These features indicate episodic, localized flow of hot, possibly CO2-rich fluids within the fault zone. The microstructure populations identified in the core samples correlate to the subsidiary fault patterns typical of strike-slip faults. The geothermal reservoir appears to be centered on the fault zone, with the principal fault strands and adjoining, highly fractured and hydrothermally altered rock serving as the main conduits for vertical fluid flow and advective heat transport from deeper magmatic sources.

Extensional tectonics and collapse structures in the Suez Rift (Egypt)

NASA Technical Reports Server (NTRS)

Chenet, P. Y.; Colletta, B.; Desforges, G.; Ousset, E.; Zaghloul, E. A.

1985-01-01

The Suez Rift is a 300 km long and 50 to 80 km wide basin which cuts a granitic and metamorphic shield of Precambrian age, covered by sediments of Paleozoic to Paleogene age. The rift structure is dominated by tilted blocks bounded by NW-SE normal faults. The reconstruction of the paleostresses indicates a N 050 extension during the whole stage of rifting. Rifting began 24 My ago with dikes intrusions; main faulting and subsidence occurred during Early Miocene producing a 80 km wide basin (Clysmic Gulf). During Pliocene and Quaternary times, faulting is still active but subsidence is restricted to a narrower area (Present Gulf). On the Eastern margin of the gulf, two sets of fault trends are predominant: (1) N 140 to 150 E faults parallel to the gulf trend with pure dip-slip displacement; and (2) cross faults, oriented NOO to N 30 E that have a strike-slip component consistent with the N 050 E distensive stress regime. The mean dip cross fault is steeper (70 to 80 deg) than the dip of the faults parallel to the Gulf (30 to 70 deg). These two sets of fault define diamond shaped tilted block. The difference of mechanical behavior between the basement rocks and the overlying sedimentary cover caused structural disharmony and distinct fault geometries.

Paleoseismology of the Mt. Narryer Fault Zone, West Central Western Australia: a Multi-Segment Intraplate Fault System

NASA Astrophysics Data System (ADS)

Whitney, B. B.; Clark, D.; Hengesh, J.

2014-12-01

The Western Australia shear zone (WASZ) is a 2000 km long fault system within the intraplate region of Australia. A paleoseismological study of faults and fault-related folds comprising the Mount Narryer fault zone (MNfz) in the southern WASZ reveals a late Quaternary history of repeated morphogenic earthquake occurrence that has profoundly influenced the planform and course of the Murchison, Roderick, and Sanford Rivers. Folding in the near surface sediments is the predominant style of surface expression of reactivated basement faults which is consistent with other neotectonic structures throughout the Western Australia shear zone. CRN and OSL estimates of exposure and burial ages of fault-related folds and fold derived colluvium provide constraint on Late Quaternary slip rates on the underlying faults of ~0.05 - 0.1 mm/a. In the case of the Roderick River fault scarp, 2-3m high tectonic risers separating inset terraces where the Murchison River crosses the scarp are consistent with multiple late Quaternary seismic events on the order of magnitude Mw 7.1-7.3. Mid-Pleistocene ages of tectonically deformed strata in the MNfz are consistent with the timing of collision between the Australian extended margin and Savu-Rote ridge 0.2-1.8 Ma.

Postobductional extension along and within the Frontal Range of the Eastern Oman Mountains

NASA Astrophysics Data System (ADS)

Mattern, Frank; Scharf, Andreas

2018-04-01

The Oman Mountains formed by late Cretaceous obduction of the Tethys-derived Semail Ophiolite. This study concerns the postobductional extension on the northern flank of the mountain belt. Nine sites at the northern margins of the Jabal Akhdar/Nakhl and Saih Hatat domes of the Eastern Oman ("Hajar") Mountains were investigated. The northern margins are marked by a system of major interconnected extensional faults, the "Frontal Range Fault". While the vertical displacements along the Saih Hatat and westerly located Jabal Nakhl domes measure 2.25-6.25 km, 0.5-4.5 km and 4-7 km, respectively, it amounts to 1-5 km along the Jabal Akhdar Dome. Extension had started during the late Cretaceous, towards the end of ophiolite emplacement. Two stages of extension can be ascertained (late Cretaceous to early Eocene and probably Oligocene) at the eastern part of the Frontal Range Fault System (Wadi Kabir and Fanja Graben faults of similar strike). Along the intervening and differently striking fault segments at Sad and Sunub the same two stages of deformation are deduced. The first stage is characterized again by extension. The second stage is marked by dextral motion, including local transtension. Probable Oligocene extension affected the Batinah Coast Fault while it also affected the Wadi Kabir Fault and the Fanja Graben. It is unclear whether the western portion of the Frontal Range Fault also went through two stages of deformation. Bedding-parallel ductile and brittle deformation is a common phenomenon. Hot springs and listwaenite are associated with dextral releasing bends within the fault system, as well as a basalt intrusion of probable Oligocene age. A structural transect through the Frontal Range along the superbly exposed Wadi Bani Kharous (Jabal Akhdar Dome) revealed that extension affected the Frontal Range at least 2.5 km south of the Frontal Range Fault. Also here, bedding-parallel shearing is important, but not exclusive. A late Cretaceous thrust was extensionally reactivated by a branch fault of the Frontal Range Fault. Extension may be ductile (limestone mylonites), ductile and brittle (ooid deformation, boudinaged belemnite rostra, shear bands) or brittle. Extension is heterogeneously distributed within the Frontal Range. Extension is mainly related to orogenic/gravitational collapse of the Oman Mountains. Collapse may have been associated with isostatic rebound and rise of the two domes. In the western part of the study area, the Frontal Range Fault has a listric morphology. It is probably horizontal at a depth of 15 km below the Batinah coastal area. The fault seems to use the clay- and tuff-bearing Aruma Group as shear horizon. The depth of 15 km may coincide with the brittle-ductile transition of quartz- and feldspar-rich rocks. Close to this depth, the listric Batinah Coast Fault curves into the Frontal Range Fault. Extension along the Frontal Range and Batinah Coast faults probably reactivated preexisting late Cretaceous thrust faults during post-late Eocene time. The latter fault is likely mechanically related to the Wadi Kabir Fault via the Fanja Graben Fault and the Sunub fault segment. Listwaenite and serpentinite cluster preferably around the extensional faults. The Semail Gap probably functioned as a sinistral transform fault or fault zone during the Permian.

A low-angle normal fault and basement structures within the Enping Sag, Pearl River Mouth Basin: Insights into late Mesozoic to early Cenozoic tectonic evolution of the South China Sea area

NASA Astrophysics Data System (ADS)

Ye, Qing; Mei, Lianfu; Shi, Hesheng; Shu, Yu; Camanni, Giovanni; Wu, Jing

2018-04-01

The basement structure of the Cenozoic Enping Sag, within the Pearl River Mouth Basin on the northern margin of South China Sea, is revealed by borehole-constrained high-quality 3D seismic reflection data. Such data suggest that the Enping Sag is bounded in the north by a low-angle normal fault. We interpret this low-angle normal fault to have developed as the result of the reactivation of a pre-existing thrust fault part of a pre-Cenozoic thrust system. This is demonstrated by the selective reactivation of the pre-existing thrust and by diffuse contractional deformation recognized from the accurate analysis of basement reflections. Another significant result of this study is the finding of some residual rift basins within the basement of the Enping Sag. Both the thrust system and the residual basins are interpreted to have developed after the emplacement of continental margin arc-related granitoids (J3-K1) that define the basement within the study area. Furthermore, seismic sections show that the pre-existing residual rift basins are offset by the main thrust fault and they are both truncated by the Tg unconformity. These structural relationships, interpreted in the frame of previous studies, help us to reconstruct a six-event structural evolution model for the Enping Sag from the late Mesozoic to the early Cenozoic. In particular, we interpret the residual rift basins to have formed as the result of back-arc extension due to the slab roll-back of the Paleo-Pacific Plate subduction in the early K2. The thrust system has recorded a compressional event in the late K2 that followed the back-arc extension in the SCS area. The mechanism of this compressional event is still to be clarified, and might be related to continuous subduction of the Paleo-Pacific Plate or to the continent-continent collision between a micro-continental block and the South China margin.

Near N-S paleo-extension in the western Deccan region, India: Does it link strike-slip tectonics with India-Seychelles rifting?

NASA Astrophysics Data System (ADS)

Misra, Achyuta Ayan; Bhattacharya, Gourab; Mukherjee, Soumyajit; Bose, Narayan

2014-09-01

This is the first detailed report and analyses of deformation from the W part of the Deccan large igneous province (DLIP), Maharashtra, India. This deformation, related to the India-Seychelles rifting during Late Cretaceous-Early Paleocene, was studied, and the paleostress tensors were deduced. Near N-S trending shear zones, lineaments, and faults were already reported without significant detail. An E-W extension was envisaged by the previous workers to explain the India-Seychelles rift at ~64 Ma. The direction of extension, however, does not match with their N-S brittle shear zones and also those faults (sub-vertical, ~NE-SW/~NW-SE, and few ~N-S) we report and emphasize in this work. Slickenside-bearing fault planes, brittle shear zones, and extension fractures in meso-scale enabled us to estimate the paleostress tensors (directions and relative magnitudes). The field study was complemented by remote sensing lineament analyses to map dykes and shear zones. Dykes emplaced along pre-existing ~N-S to ~NE-SW/~NW-SE shears/fractures. This information was used to derive regional paleostress trends. A ~NW-SE/NE-SW minimum compressive stress in the oldest Kalsubai Subgroup and a ~N-S direction for the younger Lonavala, Wai, and Salsette Subgroups were deciphered. Thus, a ~NW/NE to ~N-S extension is put forward that refutes the popular view of E-W India-Seychelles extension. Paleostress analyses indicate that this is an oblique rifted margin. Field criteria suggest only ~NE-SW and ~NW-SE, with some ~N-S strike-slip faults/brittle shear zones. We refer this deformation zone as the "Western Deccan Strike-slip Zone" (WDSZ). The observed deformation was matched with offshore tectonics deciphered mainly from faults interpreted on seismic profiles and from magnetic seafloor spreading anomalies. These geophysical findings too indicate oblique rifting in this part of the W Indian passive margin. We argue that the Seychelles microcontinent separated from India only after much of the DLIP erupted. Further studies of magma-rich passive margins with respect to timing and architecture of deformation and emplacement of volcanics are required.

Investigation of Tectonic Boundaries in Taiwan Obtained with a Hierarchical Clustering of Dense GNSS Data

NASA Astrophysics Data System (ADS)

Takahashi, A.; Hashimoto, M.; Hu, J. C.; Fukahata, Y.

2017-12-01

Taiwan Island is composed of many geological structures. The main tectonic feature is the collision of the Luzon volcanic arc with the Eurasian continent, which propagates westward and generates complicated crustal deformation. One way to model crustal deformation is to divide Taiwan island into man rigid blocks that moves relatively each other along the boundaries (deformation zones) of the blocks. Since earthquakes tend to occur in the deformation zones, identification of such tectonic boundaries is important. So far, many tectonic boundaries have been proposed on the basis of geology, geomorphology, seismology and geodesy. However, which is the most significant boundary depends on disciplines and there is no way to objectively classify them. Here, we introduce an objective method to identify significant tectonic boundaries with a hierarchical representation proposed by Simpson et al. [2012].We apply a hierarchical agglomerative clustering algorithm to dense GNSS horizontal velocity data in Taiwan. One of the significant merits of the hierarchical representation of the clustering results is that we can consistently explore crustal structures from larger to smaller scales. This is because a higher hierarchy corresponds to a larger crustal structure, and a lower hierarchy corresponds to a smaller crustal structure. Relative motion between clusters can be obtained from this analysis.The first major boundary is identified along the eastern margin of the Longitudinal Valley, which corresponds to the separation of the Philippine Sea plate and the Eurasian continental margin. The second major boundary appears along the Chaochou fault and the Chishan fault in southwestern Taiwan. The third major boundary appears along the eastern margin of the coastal plane. The identified major clusters can be divided into several smaller blocks without losing consistency with geological boundaries. For example, the Fengshun fault, concealed beneath thick sediment layers, is identified. Furthermore, obtained relative motion between clusters demands a reverse fault or a left lateral fault in the off shore of the coastal range.Our clustering based block modeling is consistent with tectonics of Taiwan, implying that observed crustal deformation in Taiwan can be attributed to motion or deformation of shallow structures.

Late Holocene activity of the Dead Sea Transform revealed in 3D palaeoseismic trenches on the Jordan Gorge segment [rapid communication

NASA Astrophysics Data System (ADS)

Marco, Shmuel; Rockwell, Thomas K.; Heimann, Ariel; Frieslander, Uri; Agnon, Amotz

2005-05-01

Three-dimensional excavations of buried stream channels that have been displaced by the Jordan Fault, the primary strand of the Dead Sea fault zone in northern Israel, demonstrate that late Holocene slip has been primarily strike-slip at a minimum rate of 3 mm/yr. The palaeoseismic study was carried out in the Bet-Zayda Valley, the delta of the Jordan River at the north shore of the Sea of Galilee. The site was chosen where a north-striking scarp with up to 1-m vertical expression crosses the flat valley. One group of trench excavations was located where a small stream crosses the scarp. The active stream, which is incised into the scarp, is not offset by the fault. However we found two palaeo channels about 2 m below the surface offset sinistrally 2.7±0.2 m by the fault and two younger nested channels offset 0.5±0.05 m. Based on radiocarbon dates we attribute the last 0.5 m rupture to the earthquake of October 30, 1759. The older offset of 2.2 m most probably occurred in the earthquakes of May 20, 1202. These two events correlate with the findings at Ateret, about 12 km north of Bet-Zayda, where the 1202 earthquake produced 1.6 m of lateral displacement in E-W-striking defence walls of a Crusader castle, and an Ottoman mosque was offset 0.5 m in the earthquake of 1759. In the second group of trenches some 60 m farther south we found another offset channel. Its northern margin is displaced 15 m sinistrally whereas the southern margin shows only 9 m of sinistral offset. The dip slip component is 1.2 m, west side down. The different amounts of margin offset can be explained by erosion of the southern margin during the first 6 m of displacement. Additional slip of 9 m accrued after the stream had been abandoned and buried by a 2-m-thick lacustrine clay layers. Radiocarbon dates on organic residue provide the age control which indicates that the 15 m of slip has accrued over the past 5 kyr, yielding a short-term slip rate of 3 mm/yr for the late Holocene. It is possible that our study covers only part of the fault zone, hence we regard this mean slip rate to be a minimum for the DST. Based on other palaeoseismic studies the best estimate for Quaternary slip rate is 4±1 mm/yr.

Frictional stability and earthquake triggering during fluid pressure stimulation of an experimental fault

NASA Astrophysics Data System (ADS)

Scuderi, M. M.; Collettini, C.; Marone, C.

2017-11-01

It is widely recognized that the significant increase of M > 3.0 earthquakes in Western Canada and the Central United States is related to underground fluid injection. Following injection, fluid overpressure lubricates the fault and reduces the effective normal stress that holds the fault in place, promoting slip. Although, this basic physical mechanism for earthquake triggering and fault slip is well understood, there are many open questions related to induced seismicity. Models of earthquake nucleation based on rate- and state-friction predict that fluid overpressure should stabilize fault slip rather than trigger earthquakes. To address this controversy, we conducted laboratory creep experiments to monitor fault slip evolution at constant shear stress while the effective normal stress was systematically reduced via increasing fluid pressure. We sheared layers of carbonate-bearing fault gouge in a double direct shear configuration within a true-triaxial pressure vessel. We show that fault slip evolution is controlled by the stress state acting on the fault and that fluid pressurization can trigger dynamic instability even in cases of rate strengthening friction, which should favor aseismic creep. During fluid pressurization, when shear and effective normal stresses reach the failure condition, accelerated creep occurs in association with fault dilation; further pressurization leads to an exponential acceleration with fault compaction and slip localization. Our work indicates that fault weakening induced by fluid pressurization can overcome rate strengthening friction resulting in fast acceleration and earthquake slip. Our work points to modifications of the standard model for earthquake nucleation to account for the effect of fluid overpressure and to accurately predict the seismic risk associated with fluid injection.

Laramide structure of the central Sangre de Cristo Mountains and adjacent Raton Basin, southern Colorado

USGS Publications Warehouse

Lindsey, D.A.

1998-01-01

Laramide structure of the central Sangre de Cristo Mountains (Culebra Range) is interpreted as a system of west-dipping, basement-involved thrusts and reverse faults. The Culebra thrust is the dominant structure in the central part of the range; it dips 30 -55?? west and brings Precambrian metamorphic base-ment rocks over unmetamorphosed Paleozoic rocks. East of the Culebra thrust, thrusts and reverse faults break the basement and overlying cover rocks into north-trending fault blocks; these boundary faults probably dip 40-60?? westward. The orientation of fault slickensides indicates oblique (northeast) slip on the Culebra thrust and dip-slip (ranging from eastward to northward) movement on adjacent faults. In sedimentary cover rocks, east-vergent anticlines overlie and merge with thrusts and reverse faults; these anticlines are interpreted as fault-propagation folds. Minor east-dipping thrusts and reverse faults (backthrusts) occur in both the hanging walls and footwalls of thrusts. The easternmost faults and folds of the Culebra Range form a continuous structural boundary between the Laramide Sangre de Cristo highland and the Raton Basin. Boundary structures consist of west-dipping frontal thrusts flanked on the basinward side by poorly exposed, east-dipping backthrusts. The backthrusts are interpreted to overlie structural wedges that have been emplaced above blind thrusts in the basin margin. West-dipping frontal thrusts and blind thrusts are interpreted to involve basement, but backthrusts are rooted in basin-margin cover rocks. At shallow structural levels where erosion has not exposed a frontal thrust, the structural boundary of the basin is represented by an anticline or monocline. Based on both regional and local stratigraphic evidence, Laramide deformation in the Culebra Range and accompanying synorogenic sedimentation in the western Raton Basin probably took place from latest Cretaceous through early Eocene time. The earliest evidence of uplift and erosion of a highland is the appearance of abundant feldspar in the Late Cretaceous Vermejo Formation. Above the Vermejo, unconformities overlain by conglomerate indicate continued thrusting and erosion of highlands from late Cretaceous (Raton) through Eocene (Cuchara) time. Eocene alluvial-fan conglomerates in the Cuchara Formation may represent erosion of the Culebra thrust block. Deposition in the Raton Basin probably shifted north from New Mexico to southern Colorado from Paleocene to Eocene time as movement on individual thrusts depressed adjacent segments of the basin.

Adaptive extended-state observer-based fault tolerant attitude control for spacecraft with reaction wheels

NASA Astrophysics Data System (ADS)

Ran, Dechao; Chen, Xiaoqian; de Ruiter, Anton; Xiao, Bing

2018-04-01

This study presents an adaptive second-order sliding control scheme to solve the attitude fault tolerant control problem of spacecraft subject to system uncertainties, external disturbances and reaction wheel faults. A novel fast terminal sliding mode is preliminarily designed to guarantee that finite-time convergence of the attitude errors can be achieved globally. Based on this novel sliding mode, an adaptive second-order observer is then designed to reconstruct the system uncertainties and the actuator faults. One feature of the proposed observer is that the design of the observer does not necessitate any priori information of the upper bounds of the system uncertainties and the actuator faults. In view of the reconstructed information supplied by the designed observer, a second-order sliding mode controller is developed to accomplish attitude maneuvers with great robustness and precise tracking accuracy. Theoretical stability analysis proves that the designed fault tolerant control scheme can achieve finite-time stability of the closed-loop system, even in the presence of reaction wheel faults and system uncertainties. Numerical simulations are also presented to demonstrate the effectiveness and superiority of the proposed control scheme over existing methodologies.

Enigmatic rift-parallel, strike-slip faults around Eyjafjörður, Northern Iceland

NASA Astrophysics Data System (ADS)

Proett, J. A.; Karson, J. A.

2014-12-01

Strike-slip faults along mid-ocean ridge spreading centers are generally thought to be restricted to transform boundaries connecting rift segments. Faults that are parallel to spreading centers are generally assumed to be normal faults associated with tectonic extension. However, clear evidence of north-south (rift-parallel), strike-slip displacements occur widely around the southern portion of Eyjafjörður, northern Iceland about 50 km west of the Northern Rift Zone. The area is south of the southernmost strand (Dalvík Lineament) of the NW-SE-trending, dextral-slip, Tjӧrnes Fracture Zone (where N-S, sinistral, strike-slip "bookshelf" faulting occurs). Faults in the Eyjafjörður area cut 8.5-10 m.y. basaltic crust and are parallel to spreading-related dikes and are commonly concentrated along dike margins. Fault rocks range from fault breccia to gouge. Riedel shears and other kinematic indicators provide unambiguous evidence of shear sense. Most faults show evidence of sinistral, strike-slip movement but smaller proportions of normal and oblique-slip faults also are present. Cross cutting relations among the different types of faults are inconsistent and appear to be related to a single deformation event. Fault slip-line kinematic analysis yields solutions indicating sinistral-normal oblique-slip overall. These results may be interpreted in terms of either previously unrecognized transform-fault bookshelf faulting or slip accommodating block rotation associated with northward propagation of the Northern Rift Zone.

Dynamical Instability Produces Transform Faults at Mid-Ocean Ridges

NASA Astrophysics Data System (ADS)

Gerya, Taras

2010-08-01

Transform faults at mid-ocean ridges—one of the most striking, yet enigmatic features of terrestrial plate tectonics—are considered to be the inherited product of preexisting fault structures. Ridge offsets along these faults therefore should remain constant with time. Here, numerical models suggest that transform faults are actively developing and result from dynamical instability of constructive plate boundaries, irrespective of previous structure. Boundary instability from asymmetric plate growth can spontaneously start in alternate directions along successive ridge sections; the resultant curved ridges become transform faults within a few million years. Fracture-related rheological weakening stabilizes ridge-parallel detachment faults. Offsets along the transform faults change continuously with time by asymmetric plate growth and discontinuously by ridge jumps.

A general program to compute the multivariable stability margin for systems with parametric uncertainty

NASA Technical Reports Server (NTRS)

Sanchez Pena, Ricardo S.; Sideris, Athanasios

1988-01-01

A computer program implementing an algorithm for computing the multivariable stability margin to check the robust stability of feedback systems with real parametric uncertainty is proposed. The authors present in some detail important aspects of the program. An example is presented using lateral directional control system.

Geophysical characterization of transtensional fault systems in the Eastern California Shear Zone-Walker Lane Belt

NASA Astrophysics Data System (ADS)

McGuire, M.; Keranen, K. M.; Stockli, D. F.; Feldman, J. D.; Keller, G. R.

2011-12-01

The Eastern California Shear Zone (ECSZ) and Walker Lane belt (WL) accommodate ~25% of plate motion between the North American and Pacific plates. Faults within the Mina deflection link the ECSZ and the WL, transferring strain from the Owens Valley and Death Valley-Fish Lake Valley fault systems to the transcurrent faults of the central Walker Lane. During the mid to late Miocene the majority of strain between these systems was transferred through the Silver Peak-Lone Mountain (SPLM) extensional complex via a shallowly dipping detachment. Strain transfer has since primarily migrated north to the Mina Deflection; however, high-angle faults bounding sedimentary basins and discrepancies between geodetic and geologic models indicate that the SPLM complex may still actively transfer a portion of the strain from the ECSZ to the WL on a younger set of faults. Establishing the pattern and amount of active strain transfer within the SPLM region is required for a full accounting of strain accommodation, and provides insight into strain partitioning at the basin scale within a broader transtensional zone. To map the active structures in and near Clayton Valley, within the SPLM region, we collected seismic reflection and refraction profiles and a dense grid of gravity readings that were merged with existing gravity data. The primary goals were to determine the geometry of the high-angle fault system, the amount and sense of offset along each fault set, connectivity of the faults, and the relationship of these faults to the Miocene detachment. Seismic reflection profiles imaged the high-angle basin-bounding normal faults and the detachment in both the footwall and hanging wall. The extensional basin is ~1 km deep, with a steep southeastern boundary, a gentle slope to the northwest, and a sharp boundary on the northwest side, suggestive of another fault system. Two subparallel dip-slip faults bound the southeast (deeper) basin margin with a large lateral velocity change (from ~2.0 km/sec in the basin fill to 4.5-5.5 km/sec in the footwall) across the basin-bounding normal fault system. Very fast (approaching 6.0 km/sec) basement underlies the basin fill. The residual gravity anomaly indicates that Clayton Valley is divided into a shallower northern basin, imaged by the seismic lines, and a deeper, more asymmetric southern basin. Faults within Clayton Valley are curvilinear in nature, similar to faults observed in other step-over systems (e.g., the Mina Deflection). Gravity profiles support the seismic reflection interpretation and indicate a high angle fault (>60 degrees) bounding the northern sub-basin on its southeast margin, with a shallower fault bounding it to the northwest. A basement high trends west-northwest and separates the northern and southern basins, and is likely bounded on its southern edge by a predominantly strike-slip fault crossing the valley. Much of the strain accommodated within the southern sub-basin appears to be transferred into southern Big Smoky Valley, northwest of Clayton Valley, via these dextral strike-slip faults that obliquely cross Clayton Valley.

Formation of an Oceanic Transform Fault During Continental Rifting

NASA Astrophysics Data System (ADS)

Illsley-Kemp, F.; Bull, J. M.; Keir, D.; Gerya, T.; Pagli, C.; Gernon, T.; Ayele, A.; Goitom, B.; Hammond, J. O. S.; Kendall, J. M.

2017-12-01

We integrate evidence from surface faults, geodetic measurements, local seismicity, and 3D numerical modelling of the subaerial Afar continental rift to show that an oceanic-style transform fault is forming during the final stages of continental breakup. Transform faults are a fundamental tenet of plate tectonics, connecting offset extensional segments of mid-ocean ridges, and are vital in palaeotectonic reconstructions of passive margins. The current consensus is that transform faults initiate after the onset of seafloor spreading. However this inference has been difficult to test given the lack of observations of transform fault formation. We present the first direct observation of transform fault initiation, and shed unprecedented light on their formation mechanisms. We demonstrate that they originate during late-stage continental rifting, earlier in the rifting cycle than previously thought. Our results have important implications for reconstructing the breakup history of the continents. Palaeotectonic reconstructions that use transform fault terminations as an indicator of the continent-ocean boundary may have placed the continent-ocean boundary landward of its true location. This will have led to an overestimation of the age of continental breakup of between 8-18 Myr. Our results therefore have significant implications for studies that rely on accurate dating of continental breakup events.

Growth trishear model and its application to the Gilbertown graben system, southwest Alabama

USGS Publications Warehouse

Jin, G.; Groshong, R.H.; Pashin, J.C.

2009-01-01

Fault-propagation folding associated with an upward propagating fault in the Gilbertown graben system is revealed by well-based 3-D subsurface mapping and dipmeter analysis. The fold is developed in the Selma chalk, which is an oil reservoir along the southern margin of the graben. Area-depth-strain analysis suggests that the Cretaceous strata were growth units, the Jurassic strata were pregrowth units, and the graben system is detached in the Louann Salt. The growth trishear model has been applied in this paper to study the evolution and kinematics of extensional fault-propagation folding. Models indicate that the propagation to slip (p/s) ratio of the underlying fault plays an important role in governing the geometry of the resulting extensional fault-propagation fold. With a greater p/s ratio, the fold is more localized in the vicinity of the propagating fault. The extensional fault-propagation fold in the Gilbertown graben is modeled by both a compactional and a non-compactional growth trishear model. Both models predict a similar geometry of the extensional fault-propagation fold. The trishear model with compaction best predicts the fold geometry. ?? 2008 Elsevier Ltd. All rights reserved.

Geomorphologic, stratigraphic and sedimentologic evidences of tectonic activity in Sone-Ganga alluvial tract in Middle Ganga Plain, India

NASA Astrophysics Data System (ADS)

Sahu, Sudarsan; Saha, Dipankar

2014-08-01

The basement of the Ganga basin in the Himalayan foreland is criss-crossed by several faults, dividing the basin into several sub-blocks forming horsts, grabens, or half-grabens. Tectonic perturbations along basement faults have affected the fluvial regime and extent of sediment fill in different parts of the basin during Late Quaternary. The East Patna Fault (EPF) and the West Patna Fault (WPF), located in Sone-Ganga alluvial tract in the southern marginal parts of Middle Ganga Plain (MGP), have remained tectonically active. The EPF particularly has acted significantly and influenced in evolving the geomorphological landscape and the stratigraphic architecture of the area. The block bounded by the two faults has earlier been considered as a single entity, constituting a half-graben. The present investigation (by morpho-stratigraphic and sedimentologic means) has revealed the existence of yet another fault within the half-graben, referred to as Bishunpur-Khagaul Fault (BKF). Many of the long profile morphological characters (e.g., knick-zone, low width-depth ratio) of the Sone River at its lower reaches can be ascribed to local structural deformation along BKF. These basement faults in MGP lie parallel to each other in NE-SW direction.

Holocene faulting in the Bellingham forearc basin: upper-plate deformation at the northern end of the Cascadia subduction zone

USGS Publications Warehouse

Kelsey, Harvey M.; Sherrod, Brian L.; Blakely, Richard J.; Haugerud, Ralph A.

2013-01-01

The northern Cascadia forearc takes up most of the strain transmitted northward via the Oregon Coast block from the northward-migrating Sierra Nevada block. The north-south contractional strain in the forearc manifests in upper-plate faults active during the Holocene, the northern-most components of which are faults within the Bellingham Basin. The Bellingham Basin is the northern of four basins of the actively deforming northern Cascadia forearc. A set of Holocene faults, Drayton Harbor, Birch Bay, and Sandy Point faults, occur within the Bellingham Basin and can be traced from onshore to offshore using a combination of aeromagnetic lineaments, paleoseismic investigations and scarps identified using LiDAR imagery. With the recognition of such Holocene faults, the northernmost margin of the actively deforming Cascadia forearc extends 60 km north of the previously recognized limit of Holocene forearc deformation. Although to date no Holocene faults are recognized at the northern boundary of the Bellingham Basin, which is 15 km north of the international border, there is no compelling tectonic reason to expect that Holocene faults are limited to south of the international border.

Three-dimensional splay fault geometry and implications for tsunami generation.

PubMed

Moore, G F; Bangs, N L; Taira, A; Kuramoto, S; Pangborn, E; Tobin, H J

2007-11-16

Megasplay faults, very long thrust faults that rise from the subduction plate boundary megathrust and intersect the sea floor at the landward edge of the accretionary prism, are thought to play a role in tsunami genesis. We imaged a megasplay thrust system along the Nankai Trough in three dimensions, which allowed us to map the splay fault geometry and its lateral continuity. The megasplay is continuous from the main plate interface fault upwards to the sea floor, where it cuts older thrust slices of the frontal accretionary prism. The thrust geometry and evidence of large-scale slumping of surficial sediments show that the fault is active and that the activity has evolved toward the landward direction with time, contrary to the usual seaward progression of accretionary thrusts. The megasplay fault has progressively steepened, substantially increasing the potential for vertical uplift of the sea floor with slip. We conclude that slip on the megasplay fault most likely contributed to generating devastating historic tsunamis, such as the 1944 moment magnitude 8.1 Tonankai event, and it is this geometry that makes this margin and others like it particularly prone to tsunami genesis.

Geology of the continental margin beneath Santa Monica Bay, Southern California, from seismic-reflection data

USGS Publications Warehouse

Fisher, M.A.; Normark, W.R.; Bohannon, R.G.; Sliter, R.W.; Calvert, A.J.

2003-01-01

We interpret seismic-reflection data, which were collected in Santa Monica Bay using a 70-in3 generator-injector air gun, to show the geologic structure of the continental shelf and slope and of the deep-water, Santa Monica and San Pedro Basins. The goal of this research is to investigate the earthquake hazard posed to urban areas by offshore faults. These data reveal that northwest of the Palos Verdes Peninsula, the Palos Verdes Fault neither offsets the seafloor nor cuts through an undeformed sediment apron that postdates the last sea level rise. Other evidence indicates that this fault extends northwest beneath the shelf in the deep subsurface. However, other major faults in the study area, such as the Dume and San Pedro Basin Faults, were active recently, as indicated by an arched seafloor and offset shallow sediment. Rocks under the lower continental slope are deformed to differing degrees on opposite sides of Santa Monica Canyon. Northwest of this canyon, the continental slope is underlain by a little-deformed sediment apron; the main structures that deform this apron are two lower-slope anticlines that extend toward Point Dume and are cored by faults showing reverse or thrust separation. Southeast of Santa Monica Canyon, lower-slope rocks are deformed by a complex arrangement of strike-slip, normal, and reverse faults. The San Pedro Escarpment rises abruptly along the southeast side of Santa Monica Canyon. Reverse faults and folds underpinning this escarpment steepen progressively southeastward. Locally they form flower structures and cut downward into basement rocks. These faults merge downward with the San Pedro Basin fault zone, which is nearly vertical and strike slip. The escarpment and its attendant structures diverge from this strike-slip fault zone and extend for 60 km along the margin, separating the continental shelf from the deep-water basins. The deep-water Santa Monica Basin has large extent but is filled with only a thin (less than 1.5-km) section of what are probably post-Miocene rocks and sediment. Extrapolating ages obtained from Ocean Drilling Program site 1015 indicates that this sedimentary cover is Quaternary, possibly no older than 600 ka. Folds and faults along the base of the San Pedro Escarpment began to form during 8-13 ka ago. Refraction-velocity data show that high-velocity rocks, probably the Catalina Schist or Miocene volcanic rocks, underlie the sedimentary section. The San Pedro Basin developed along a strike-slip fault, widens to the southeast, and is deformed by faults having apparent reverse separation and by folds near Redondo Canyon and the Palos Verdes Peninsula.

Self-stabilizing byzantine-fault-tolerant clock synchronization system and method

NASA Technical Reports Server (NTRS)

Malekpour, Mahyar R. (Inventor)

2012-01-01

Systems and methods for rapid Byzantine-fault-tolerant self-stabilizing clock synchronization are provided. The systems and methods are based on a protocol comprising a state machine and a set of monitors that execute once every local oscillator tick. The protocol is independent of specific application specific requirements. The faults are assumed to be arbitrary and/or malicious. All timing measures of variables are based on the node's local clock and thus no central clock or externally generated pulse is used. Instances of the protocol are shown to tolerate bursts of transient failures and deterministically converge with a linear convergence time with respect to the synchronization period as predicted.

Pre-existing normal faults have limited control on the rift geometry of the northern North Sea

NASA Astrophysics Data System (ADS)

Claringbould, Johan S.; Bell, Rebecca E.; Jackson, Christopher A.-L.; Gawthorpe, Robert L.; Odinsen, Tore

2017-10-01

Many rifts develop in response to multiphase extension with numerical and physical models suggesting that reactivation of first-phase normal faults and rift-related variations in bulk crustal rheology control the evolution and final geometry of subsequent rifts. However, many natural multiphase rifts are deeply buried and thus poorly exposed in the field and poorly imaged in seismic reflection data, making it difficult to test these models. Here we integrate recent 3D seismic reflection and borehole data across the entire East Shetland Basin, northern North Sea, to constrain the long-term, regional development of this multiphase rift. We document the following key stages of basin development: (i) pre-Triassic to earliest Triassic development of multiple sub-basins controlled by widely distributed, NNW- to NE-trending, east- and west-dipping faults; (ii) Triassic activity on a single major, NE-trending, west-dipping fault located near the basins western margin, and formation of a large half-graben; and (iii) Jurassic development of a large, E-dipping, N- to NE-trending half-graben near the eastern margin of the basin, which was associated with rift narrowing and strain focusing in the Viking Graben. In contrast to previous studies, which argue for two discrete periods of rifting during the Permian-Triassic and Late Jurassic-Early Cretaceous, we find that rifting in the East Shetland Basin was protracted from pre-Triassic to Cretaceous. We find that, during the Jurassic, most pre-Jurassic normal faults were buried and in some cases cross-cut by newly formed faults, with only a few being reactivated. Previously developed faults thus had only a limited control on the evolution and geometry of the later rift. We instead argue that strain migration and rift narrowing was linked to the evolving thermal state of the lithosphere, an interpretation supporting the predictions of lithosphere-scale numerical models. Our study indicates that additional regional studies of natural rifts are required to test and refine the predictions of physical and numerical models, more specifically, our study suggests models not explicitly recognising or including thermal or rheological effects might over emphasise the role of discrete pre-existing rift structures such as normal faults.

Latest Miocene transtensional rifting of northeast Isla Tiburón, eastern margin of the Gulf of California

NASA Astrophysics Data System (ADS)

Bennett, Scott E. K.; Oskin, Michael E.; Iriondo, Alexander

2017-11-01

Details about the timing and kinematics of rifting are crucial to understand the conditions that led to strain localization, continental rupture, and formation of the Gulf of California ocean basin. We integrate detailed geologic and structural mapping, basin analysis, and geochronology to characterize transtensional rifting on northeastern Isla Tiburón, a proximal onshore exposure of the rifted North America margin, adjacent to the axis of the Gulf of California. Slip on the Kunkaak normal fault tilted its hanging wall down-to-the-east 70° and formed the non-marine Tecomate basin, deposited across a 20° angular unconformity. From 7.1-6.4 Ma, the hanging wall tilted at 35 ± 5°/Myr, while non-marine sandstone and conglomerate accumulated at 1.4 ± 0.2 mm/yr. At least 1.8 ± 0.1 km of sediments and pyroclastic deposits accumulated in the Tecomate basin concurrent with clockwise vertical-axis block rotation and 2.8 km of total dip-slip motion on the Kunkaak fault. Linear extrapolation of tilting and sedimentation rates suggests that faulting and basin deposition initiated 7.6-7.4 Ma, but an older history involving initially slower rates is permissible. The Kunkaak fault and Tecomate basin are truncated by NW-striking, dextral-oblique structures, including the Yawassag fault, which accrued > 8 km of post-6.4 Ma dextral displacement. The Coastal Sonora fault zone on mainland Sonora, which accrued several tens of kilometers of late Miocene dextral offset, continues to the northwest, across northeastern Isla Tiburón and offshore into the Gulf of California. The establishment of rapid, latest Miocene transtension in the Coastal Sonora fault zone was synchronous with the 8-7 Ma onset of transform faulting and basin formation along the nascent Pacific-North America plate boundary throughout northwestern Mexico and southern California. Plate boundary strain localized into this Gulf of California shear zone, a narrow transtensional belt that subsequently hosted the marine incursion and continental rupture in the Gulf of California.

The Agost Basin (Betic Cordillera, Alicante province, Spain): a pull-apart basin involving salt tectonics

NASA Astrophysics Data System (ADS)

Martín-Martín, Manuel; Estévez, Antonio; Martín-Rojas, Ivan; Guerrera, Francesco; Alcalá, Francisco J.; Serrano, Francisco; Tramontana, Mario

2018-03-01

The Agost Basin is characterized by a Miocene-Quaternary shallow marine and continental infilling controlled by the evolution of several curvilinear faults involving salt tectonics derived from Triassic rocks. From the Serravallian on, the area experienced a horizontal maximum compression with a rotation of the maximum stress axis from E-W to N-S. The resulting deformation gave rise to a strike-slip fault whose evolution is characterized progressively by three stages: (1) stepover/releasing bend with a dextral motion of blocks; (2) very close to pure horizontal compression; and (3) restraining bend with a sinistral movement of blocks. In particular, after an incipient fracturing stage, faults generated a pull-apart basin with terraced sidewall fault and graben subzones developed in the context of a dextral stepover during the lower part of late Miocene p.p. The occurrence of Triassic shales and evaporites played a fundamental role in the tectonic evolution of the study area. The salty material flowed along faults during this stage generating salt walls in root zones and salt push-up structures at the surface. During the purely compressive stage (middle part of late Miocene p.p.) the salt walls were squeezed to form extrusive mushroom-like structures. The large amount of clayish and salty material that surfaced was rapidly eroded and deposited into the basin, generating prograding fan clinoforms. The occurrence of shales and evaporites (both in the margins of the basin and in the proper infilling) favored folding of basin deposits, faulting, and the formation of rising blocks. Later, in the last stage (upper part of late Miocene p.p.), the area was affected by sinistral restraining conditions and faults must have bent to their current shape. The progressive folding of the basin and deformation of margins changed the supply points and finally caused the end of deposition and the beginning of the current erosive systems. On the basis of the interdisciplinary results, the Agost Basin can be considered a key case of the interference between salt tectonics and the evolution of strike-slip fault zones. The reconstructed model has been compared with several scaled sandbox analogical models and with some natural pull-apart basins.

Active Tectonics of the Far North Pacific Observed with GPS

NASA Astrophysics Data System (ADS)

Elliott, J.; Freymueller, J. T.; Jiang, Y.; Leonard, L. J.; Hyndman, R. D.; Mazzotti, S.

2017-12-01

The idea that the tectonics of the northeastern Pacific is defined by relatively discrete deformation along the boundary between the Pacific and North American plates has given way to a more complex picture of broad plate boundary zones and distributed deformation. This is due in large part to the Plate Boundary Observatory and several focused GPS studies, which have greatly increased the density of high-quality GPS data throughout the region. We will present an updated GPS velocity field in a consistent reference frame as well as a new, integrated block model that sheds light on regional tectonics and provides improved estimates of motion along faults and their potential seismic hazard. Crustal motions in southern Alaska are strongly influenced by the collision and flat-slab subduction of the Yakutat block along the central Gulf of Alaska margin. In the area nearest to the collisional front, small blocks showing evidence of internal deformation are required. East of the front, block motions show clockwise rotation into the Canadian Cordillera while west of the front there are counterclockwise rotations that extend along the Alaska forearc, suggesting crustal extrusion. Farther from the convergent margin, the crust appears to move as rigid blocks, with uniform motion over large areas. In western Alaska, block motions show a southwesterly rotation into the Bering Sea. Arctic Alaska displays southeasterly motions that gradually transition into easterly motion in Canada. Much of the southeastern Alaska panhandle and coastal British Columbia exhibit northwesterly motions. Although the relative plate motions are mainly accommodated along major faults systems, including the Fairweather-Queen Charlotte transform system, the St. Elias fold-and-thrust belt, the Denali-Totschunda system, and the Alaska-Aleutian subduction zone, a number of other faults accommodate lesser but still significant amounts of motion in the model. These faults include the eastern Denali/Duke River system, the Castle Mountain fault, the western Denali fault, the Kaltag fault, and the Kobuk fault. Based on the expanded GPS data set, locked or partially locked sections of the Alaska subduction zone may extend as far north and east as the eastern Alaska Range.

Geophysical Characterization of Groundwater-Fault Dynamics at San Andreas Oasis

NASA Astrophysics Data System (ADS)

Faherty, D.; Polet, J.; Osborn, S. G.

2017-12-01

The San Andreas Oasis has historically provided a reliable source of fresh water near the northeast margin of the Salton Sea, although since the recent completion of the Coachella Canal Lining Project and persistent drought in California, surface water at the site has begun to disappear. This may be an effect of the canal lining, however, the controls on groundwater are complicated by the presence of the Hidden Springs Fault (HSF), a northeast dipping normal fault that trends near the San Andreas Oasis. Its surface expression is apparent as a lineation against which all plant growth terminates, suggesting that it may form a partial barrier to subsurface groundwater flow. Numerous environmental studies have detailed the chemical evolution of waters resources at San Andreas Spring, although there remains a knowledge gap on the HSF and its relation to groundwater at the site. To better constrain flow paths and characterize groundwater-fault interactions, we have employed resistivity surveys near the surface trace of the HSF to generate profiles of lateral and depth-dependent variations in resistivity. The survey design is comprised of lines installed in Wenner Arrays, using an IRIS Syscal Kid, with 24 electrodes, at a maximum electrode spacing of 5 meters. In addition, we have gathered constraints on the geometry of the HSF using a combination of ground-based magnetic and gravity profiles, conducted with a GEM walking Proton Precession magnetometer and a Lacoste & Romberg gravimeter. Seventeen gravity measurements were acquired across the surface trace of the fault. Preliminary resistivity results depict a shallow conductor localized at the oasis and discontinuous across the HSF. Magnetic data reveal a large contrast in subsurface magnetic susceptibility that appears coincident with the surface trace and trend of the HSF, while gravity data suggests a shallow, relatively high density anomaly centered near the oasis. These data also hint at a second, previously undocumented fault bounding the opposite margin of the oasis and trending subparallel to the HSF. We thus speculate that the Hidden Springs Fault and this possible secondary fault act as partial barriers to lateral subsurface flow and form a structural wedge, localizing groundwater beneath the oasis.

Thinning Mechanism of the South China Sea Crust: New Insight from the Deep Crustal Images

NASA Astrophysics Data System (ADS)

Chang, S. P.; Pubellier, M. F.; Delescluse, M.; Qiu, Y.; Liang, Y.; Chamot-Rooke, N. R. A.; Nie, X.; Wang, J.

2017-12-01

The passive margin in the South China Sea (SCS) has experienced a long-lived extension period from Paleocene to late Miocene, as well as an extreme stretching which implies an unusual fault system to accommodate the whole amount of extension. Previous interpretations of the fault system need to be revised to explain the amount of strain. We study a long multichannel seismic profile crossing the whole rifted margin in the southwest of SCS, using 6 km- and 8 km-long streamers. After de-multiple processing by SRME, Radon and F-K filtering, an enhanced image of the crustal geometry, especially on the deep crust, allows us to illustrate two levels of detachment at depth. The deeper detachment is around 7-8 sec TWT in the profile. The faults rooting at this detachment are characterized by large offset and are responsible for thicker synrift sediment. A few of these faults appear to reach the Moho. The geometry of the acoustic basement between these boundary faults suggests gentle tilting with a long wavelength ( 200km), and implies some internal deformation. The shallower detachment is located around 4-5 sec TWT. The faults rooting at this detachment represent smaller offset, a shorter wavelength of the basement and thinner packages of synrift sediment. Two detachments separate the crust into upper, middle and lower crust. If the lower crust shows ductile behavior, the upper and middle crust is mostly brittle and form large wavelength boudinage structure, and the internal deformation of the boudins might imply low friction detachments at shallower levels. The faults rooting to deep detachment have activated during the whole rifting period until the breakup. Within the upper and middle crust, the faults resulted in important tilting of the basement at shallow depth, and connect to the deep detachment at some places. The crustal geometry illustrates how the two detachments are important for the thinning process, and also constitute a pathway for the following magmatic activity from the mantle to the surface.

An empirically based steady state friction law and implications for fault stability

NASA Astrophysics Data System (ADS)

Spagnuolo, E.; Nielsen, S.; Violay, M.; Di Toro, G.

2016-04-01

Empirically based rate-and-state friction laws (RSFLs) have been proposed to model the dependence of friction forces with slip and time. The relevance of the RSFL for earthquake mechanics is that few constitutive parameters define critical conditions for fault stability (i.e., critical stiffness and frictional fault behavior). However, the RSFLs were determined from experiments conducted at subseismic slip rates (V < 1 cm/s), and their extrapolation to earthquake deformation conditions (V > 0.1 m/s) remains questionable on the basis of the experimental evidence of (1) large dynamic weakening and (2) activation of particular fault lubrication processes at seismic slip rates. Here we propose a modified RSFL (MFL) based on the review of a large published and unpublished data set of rock friction experiments performed with different testing machines. The MFL, valid at steady state conditions from subseismic to seismic slip rates (0.1 µm/s < V < 3 m/s), describes the initiation of a substantial velocity weakening in the 1-20 cm/s range resulting in a critical stiffness increase that creates a peak of potential instability in that velocity regime. The MFL leads to a new definition of fault frictional stability with implications for slip event styles and relevance for models of seismic rupture nucleation, propagation, and arrest.

A Self-Stabilizing Byzantine-Fault-Tolerant Clock Synchronization Protocol

NASA Technical Reports Server (NTRS)

Malekpour, Mahyar R.

2009-01-01

This report presents a rapid Byzantine-fault-tolerant self-stabilizing clock synchronization protocol that is independent of application-specific requirements. It is focused on clock synchronization of a system in the presence of Byzantine faults after the cause of any transient faults has dissipated. A model of this protocol is mechanically verified using the Symbolic Model Verifier (SMV) [SMV] where the entire state space is examined and proven to self-stabilize in the presence of one arbitrary faulty node. Instances of the protocol are proven to tolerate bursts of transient failures and deterministically converge with a linear convergence time with respect to the synchronization period. This protocol does not rely on assumptions about the initial state of the system other than the presence of sufficient number of good nodes. All timing measures of variables are based on the node s local clock, and no central clock or externally generated pulse is used. The Byzantine faulty behavior modeled here is a node with arbitrarily malicious behavior that is allowed to influence other nodes at every clock tick. The only constraint is that the interactions are restricted to defined interfaces.

New insights into North America-Pacific Plate boundary deformation from Lake Tahoe, Salton Sea and southern Baja California

NASA Astrophysics Data System (ADS)

Brothers, Daniel Stephen

Five studies along the Pacific-North America (PA-NA) plate boundary offer new insights into continental margin processes, the development of the PA-NA tectonic margin and regional earthquake hazards. This research is based on the collection and analysis of several new marine geophysical and geological datasets. Two studies used seismic CHIRP surveys and sediment coring in Fallen Leaf Lake (FLL) and Lake Tahoe to constrain tectonic and geomorphic processes in the lakes, but also the slip-rate and earthquake history along the West Tahoe-Dollar Point Fault. CHIRP profiles image vertically offset and folded strata that record deformation associated with the most recent event (MRE). Radiocarbon dating of organic material extracted from piston cores constrain the age of the MRE to be between 4.1--4.5 k.y. B.P. Offset of Tioga aged glacial deposits yield a slip rate of 0.4--0.8 mm/yr. An ancillary study in FLL determined that submerged, in situ pine trees that date to between 900-1250 AD are related to a medieval megadrought in the Lake Tahoe Basin. The timing and severity of this event match medieval megadroughts observed in the western United States and in Europe. CHIRP profiles acquired in the Salton Sea, California provide new insights into the processes that control pull-apart basin development and earthquake hazards along the southernmost San Andreas Fault. Differential subsidence (>10 mm/yr) in the southern sea suggests the existence of northwest-dipping basin-bounding faults near the southern shoreline. In contrast to previous models, the rapid subsidence and fault architecture observed in the southern part of the sea are consistent with experimental models for pull-apart basins. Geophysical surveys imaged more than 15 ˜N15°E oriented faults, some of which have produced up to 10 events in the last 2-3 kyr. Potentially 2 of the last 5 events on the southern San Andreas Fault (SAF) were synchronous with rupture on offshore faults, but it appears that ruptures on three offshore faults are synchronous with Colorado River diversions into the basin. The final study was used coincident wide-angle seismic refraction and multichannel seismic reflection surveys that spanned the width of the of the southern Baja California (BC) Peninsula. The data provide insight into the spatial and temporal evolution of the BC microplate capture by the Pacific Plate. Seismic reflection profiles constrain the upper crustal structure and deformation history along fault zone on the western Baja margin and in the Gulf of California. Stratal divergence in two transtensional basins along the Magdalena Shelf records the onset of extension across the Tosco-Abreojos and Santa Margarita faults. We define an upper bound of 12 Ma on the age of the pre-rift sediments and an age of ˜8 Ma for the onset of extension. Tomographic imaging reveals a very heterogeneous upper crust and a narrow, high velocity zone that extends ˜40 km east of the paleotrench and is interpreted to be remnant oceanic crust.

Cosesimic landslides and their post-quake effects (Invited)

NASA Astrophysics Data System (ADS)

Huang, R.; Fan, X.

2013-12-01

On May 12, 2008, a devastating earthquake of magnitude Mw 7.9 hit China's Sichuan province. The quake, originating in the Longmen Shan fault zone at the eastern margin of Tibetan Plateau, was the country's largest seismic event in more than 50 years. It triggered more than 60,000 destructive landslides and 828 landslide dams over an area of 35,000 square kilometers, that caused about one third of the total fatalities. The combination of strong and long-lasting ground shaking, steep, rugged topography and a fragile and densely jointed lithology probably controlled the occurrence of landslides during the earthquake, but we found that other two factors (fault type and slip rate during the earthquake), may also have played a role. Landslides were clustered in a much wider corridor along the thrusting part of the Yingxiu-Beichuan fault than the strike-slip part. Large-scale landslides with an area of more than 50,000 m2 were concentrated where fault slip-rates were highest, near the intersections and junctures of individual segments of the fault. After the earthquake, debris flow hazard has become a significant concern. A tremendous amount of loose material from landslides that occurred during the earthquake is suspended on the hillslopes, ready to be eroded and transported by rain. More than 2000 occurrences of debris flow have been recorded by the Land and Resources Department of Sichuan Province following the 2008 quake till 2012. The threshold in hourly rainfall intensity for triggering debris flows was found to be around 60% lower after the earthquake than it had been before, according to the record in Beichuan. How long it will take for the debris flow frequency to return to pre-earthquake levels depends on a large number of factors, including rainfall intensity, natural re-vegetation and self-stabilization processes on slopes. We anticipate that - despite large uncertainties - debris flows that directly result from sediment movement during the 2008 earthquake may remain active for another two decades. Presumably, their frequency will decline over time, which may draw out the effect even longer. Heightened landslide frequency after a quake, with potential secondary effects like river damming and subsequent floods, need more focused attention.

Sedimentary evidence of historical and prehistorical earthquakes along the Venta de Bravo Fault System, Acambay Graben (Central Mexico)

NASA Astrophysics Data System (ADS)

Lacan, Pierre; Ortuño, María; Audin, Laurence; Perea, Hector; Baize, Stephane; Aguirre-Díaz, Gerardo; Zúñiga, F. Ramón

2018-03-01

The Venta de Bravo normal fault is one of the longest structures in the intra-arc fault system of the Trans-Mexican Volcanic Belt. It defines, together with the Pastores Fault, the 80 km long southern margin of the Acambay Graben. We focus on the westernmost segment of the Venta de Bravo Fault and provide new paleoseismological information, evaluate its earthquake history, and assess the related seismic hazard. We analyzed five trenches, distributed at three different sites, in which Holocene surface faulting offsets interbedded volcanoclastic, fluvio-lacustrine and colluvial deposits. Despite the lack of known historical destructive earthquakes along this fault, we found evidence of at least eight earthquakes during the late Quaternary. Our results indicate that this is one of the major seismic sources of the Acambay Graben, capable of producing by itself earthquakes with magnitudes (MW) up to 6.9, with a slip rate of 0.22-0.24 mm yr- 1 and a recurrence interval between 1940 and 2390 years. In addition, a possible multi-fault rupture of the Venta de Bravo Fault together with other faults of the Acambay Graben could result in a MW > 7 earthquake. These new slip rates, earthquake recurrence rates, and estimation of slips per event help advance our understanding of the seismic hazard posed by the Venta de Bravo Fault and provide new parameters for further hazard assessment.

Seismicity of the Earth 1900-2010 eastern margin of the Australia plate

USGS Publications Warehouse

Benz, Harley M.; Herman, Matthew; Tarr, Arthur C.; Hayes, Gavin P.; Furlong, Kevin P.; Villaseñor, Antonio; Dart, Richard L.; Rhea, Susan

2011-01-01

The eastern margin of the Australia plate is one of the most seismically active areas of the world due to high rates of convergence between the Australia and Pacific plates. In the region of New Zealand, the 3,000 km long Australia-Pacific plate boundary extends from south of Macquarie Island to the southern Kermadec Island chain. It includes an oceanic transform (the Macquarie Ridge), two oppositely verging subduction zones (Puysegur and Hikurangi), and a transpressive continental transform, the Alpine Fault through South Island, New Zealand. Since 1900, there have been 15 M7.5+ earthquakes recorded near New Zealand. Nine of these, and the four largest, occurred along or near the Macquarie Ridge, including the 1989 M8.2 event on the ridge itself, and the 2004 M8.1 event 200 km to the west of the plate boundary, reflecting intraplate deformation. The largest recorded earthquake in New Zealand itself was the 1931 M7.8 Hawke's Bay earthquake, which killed 256 people. The last M7.5+ earthquake along the Alpine Fault was 170 years ago; studies of the faults' strain accumulation suggest that similar events are likely to occur again.

SHEEP MOUNTAIN WILDERNESS STUDY AREA, WYOMING.

USGS Publications Warehouse

Houston, Robert S.; Patten, Lowell L.

1984-01-01

On the basis of a mineral survey the Sheep Mountain Wilderness study area in Wyoming was determined to offer little promise for metallic mineral resources. There is a probable potential for oil and gas resources in a small part of the study area along its northeast margin. Geophysical studies, such as reflection seismic profiling would help define the oil and gas potential in fault-controlled structures, such as those beneath the thrust fault that crops out along the east flank of Sheep Mountain.

Interrelation between rifting, faulting, sedimentation, and mantle serpentinization during continental margin formation

NASA Astrophysics Data System (ADS)

Rupke, L.; Schmid, D. W.; Perez-Gussinye, M.; Hartz, E. H.

2013-12-01

We explore the conditions under which mantle serpentinization may take place during continental rifting with 2D thermotectonostratigraphic basin models. The basic concept follows the idea that the entire extending continental crust has to be brittle for crustal scale faulting and mantle serpentinization to occur. The new model tracks the rheological evolution of the continental crust and allows for kinetically controlled mantle serpentinization processes. The isostatic and latent heat effects of the reaction are fully coupled to the structural and thermal solutions. A systematic parameter study shows that a critical stretching factor exists for which complete crustal embrittlement and serpentinization occurs. Sedimentation shifts this critical stretching factor to higher values as both deeper burial and the low thermal conductivity of sediments lead to higher crustal temperatures. Serpentinization reactions are therefore only likely in settings with low sedimentation rates and high stretching factors. In addition, we find that the rate of sediment supply has first order controls on the rheology of the lower crust, which may control the overall margin geometry. We further test these concepts in ideas in a case study for the Norwegian margin. In particular, we evaluate whether the inner lower crustal bodies (LCB) imaged beneath the More and Voring margin could be serpentinized mantle. For this purpose we reconstruct multiple 2D transects through a 3D data set. This reconstruction of the Norwegian margin shows that serpentinization reactions are indeed possible and likely during the Jurassic rift phase. Predicted present-day thicknesses and locations of partially serpentinized mantle rocks fit well to information on LCBs from seismic and gravity data. We conclude that some of the inner LCBs beneath the Norwegian margin may, in fact, be partially serpentinized mantle.

The Research of Tectonic Framework and the Fault Activity in Large Detachment Basin System on Northern Margin of South China Sea

NASA Astrophysics Data System (ADS)

Pan, L., Sr.; Ren, J.

2017-12-01

The South China Sea (SCS) is one of the largest marginal sea on southeast Asia continental margin, developed Paleogene extension-rifting continental margin system which is rare in the world and preserving many deformed characterizes of this kind system. With the investigation of the SCS, guiding by the development of tectonics and geo-physics, especially the development of tectonics and the high quality seismic data based on the development of geo-physics, people gradually accept that the northern margin of the SCS has some detachment basin characterizes. After researching the northern margin of the SCS, we come up with lithosphere profiles across the shelf, slope and deep sea basin in the northeast of the SCS to confirm the tectonic style of ocean-continental transition and the property of the detachment fault. Furthermore, we describe the outline of large detachment basins at northern SCS. Based on the large number of high-quality 2D and 3D deep seismic profile(TWT,10s), drilling and logging data, combined with domestic and international relevant researches, using basin dynamics and tectono-stratigraphy theory, techniques and methods of geology and geophysics, qualitative and quantitative, we describe the formation of the detachment basin and calculate the fault activity rate, stretching factor and settlement. According to the research, we propose that there is a giant and complete detachment basin system in the northern SCS and suggest three conclusions. First of all, the detachment basin system can be divided into three domains: proximal domain covering the Yangjiang Sag, Shenhu uplift and part of Shunde Sag, necking zone covering part of the Shunde Sag and Heshan Sag, distal domain covering most part of Heshan Sag. Second, the difference of the stretching factor is observed along the three domains of the detachment basin system. The factor of the proximal domain is the minimum among them. On the other side, the distal domain is the maximum among them. This phenomenon can be concluded as the factor is gradually increasing from the continent to the ocean. Third, the development of detachment basin is episodic which can be divided into two stages approximately: the rifting and thermal subsidence.

Deformation from the 1989 Loma Prieta earthquake near the southwest margin of the Santa Clara Valley, California

USGS Publications Warehouse

Schmidt, Kevin M.; Ellen, Stephen D.; Peterson, David M.

2014-01-01

To gain additional measurement of any permanent ground deformation that accompanied this damage, we compiled and conducted post-earthquake surveys along two 5-km lines of horizontal control and a 15-km level line. Measurements of horizontal distortion indicate approximately 0.1 m shortening in a NE-SW direction across the valley margin, similar to the amount measured in the channel lining. Evaluation of precise leveling by the National Geodetic Survey showed a downwarp, with an amplitude of >0.1 m over a span of >12 km, that resembled regional geodetic models of coseismic deformation. Although the leveling indicates broad, regional warping, abrupt discontinuities characteristic of faulting characterize both the broad-scale distribution of damage and the local deformation of the channel lining. Reverse movement largely along preexisting faults and probably enhanced significantly by warping combined with enhanced ground shaking, produced the documented coseismic ground deformation.

Lower plate serpentinite diapirism in the Calabrian Arc subduction complex.

PubMed

Polonia, A; Torelli, L; Gasperini, L; Cocchi, L; Muccini, F; Bonatti, E; Hensen, C; Schmidt, M; Romano, S; Artoni, A; Carlini, M

2017-12-19

Mantle-derived serpentinites have been detected at magma-poor rifted margins and above subduction zones, where they are usually produced by fluids released from the slab to the mantle wedge. Here we show evidence of a new class of serpentinite diapirs within the external subduction system of the Calabrian Arc, derived directly from the lower plate. Mantle serpentinites rise through lithospheric faults caused by incipient rifting and the collapse of the accretionary wedge. Mantle-derived diapirism is not linked directly to subduction processes. The serpentinites, formed probably during Mesozoic Tethyan rifting, were carried below the subduction system by plate convergence; lithospheric faults driving margin segmentation act as windows through which inherited serpentinites rise to the sub-seafloor. The discovery of deep-seated seismogenic features coupled with inherited lower plate serpentinite diapirs, provides constraints on mechanisms exposing altered products of mantle peridotite at the seafloor long time after their formation.

Structural evolution of the Ural-Tian Shan junction: A view from Karatau ridge, South Kazakhstan

NASA Astrophysics Data System (ADS)

Alexeiev, Dmitriy V.; Cook, Harry E.; Buvtyshkin, Vasiliy M.; Golub, Lyudmila Y.

2009-02-01

The deformation history of the Late Palaeozoic Ural-Tian Shan junction is discussed for the example of the Karatau ridge in southern Kazakhstan. Three deformation events are recognized. The Late Carboniferous D1 event is characterized by Laramide-style thrust-and-fold structures on the southern margin of Kazakhstan with shortening in a NE-SW direction. The Latest Permian and Triassic D2 event is controlled by compression in an east-west direction, which reflects collisional deformation in the Urals. The main structures are submeridional folds and north-west-striking sinistral strike-slip faults. The Triassic D3 event with shortening in a north-south direction reflects collision of the Turan microcontinent against the southern margin of Kazakhstan. The main structures are north-west-striking dextral strike-slip faults. Our new data provides important clues for the reconstruction of pre-Cretaceous structures between the Urals and the Tian Shan.

Map of Distribution of Bottom Sediments on the Continental Shelf, Gulf of Alaska

USGS Publications Warehouse

Evans, Kevin R.; Carlson, Paul R.; Hampton, Monty A.; Marlow, Michael S.; Barnes, Peter W.

2000-01-01

Introduction The U.S. Geological Survey has a long history of exploring marine geology in the Gulf of Alaska. As part of a cooperative program with other federal and state agencies, the USGS is investigating the relations between ocean-floor geology and benthic marine biohabitats. This bottom sediment map, compiled from published literature will help marine biologists develop an understanding of sea-floor geology in relation to various biological habitats. The pattern of sea-floor sedimentation and bottom morphology in the Gulf of Alaska reflects a complex interplay of regional tectonism, glacial advances and retreats, oceanic and tidal currents, waves, storms, eustatic change, and gravity-driven processes. This map, based on numerous cruises during the period of 1970-1996, shows distribution of bottom sediments in areas of study on the continental shelf. The samples were collected with piston, box, and gravity corers, and grab samplers. The interpretations of sediment distribution are the products of sediment size analyses combined with interpretations of high-resolution seismic reflection profiles. The sea floor was separated into several areas as follows: Cook Inlet -- Hazards studies in this embayment emphasized sediment distribution, sediment dynamics, bedforms, shallow faults, and seafloor stability. Migrating mega-sandwaves, driven by strong tidal currents, influence seabed habitats and stability of the seafloor, especially near pipelines and drilling platforms. The coarseness of the bottom sediment reinforces the influence of the strong tidal currents on the seafloor habitats. Kodiak Shelf -- Tectonic framework studies demonstrate the development of an accretionary wedge as the Pacific Plate underthrusts the Alaskan landmass. Seismic data across the accretionary wedge reveal anomalies indicative of fluid/gas vent sites in this segment of the continental margin. Geologic hazards research shows that movement along numerous shallow faults poses a risk to sea floor structures. Sea-floor sediment on shallow banks is eroded by seasonal wave-generated currents. The winnowing action of the large storm waves results in concentrations of gravel over broad segments of the Kodiak shelf. Northeastern Gulf of Alaska -- Tectonic framework studies demonstrate that rocks of distant origin (Yakutat terrane) are currently attached to and moving with the Pacific Plate, as it collides with and is subducted beneath southern Alaska. This collision process has led to pronounced structural deformation of the continental margin and adjacent southern Alaska. Consequences include rapidly rising mountains and high fluvial and glacial sedimentation rates on the adjacent margin and ocean floor. The northeastern Gulf of Alaska shelf also has concentrations of winnowed (lag) gravel on Tarr Bank and on the outer shelf southeast of Yakutat Bay. Between Kayak Island and Yakutat Bay the outer shelf consists of pebbly mud (diamict). This diamict is a product of glacial marine sedimentation during the Pleistocene and is present today as a relict sediment. A prograding wedge of Holocene sediment consisting of nearshore sand grading seaward into clayey silt and silty clay covers the relict pebbly mud to mid-shelf and beyond. Shelf and slope channel systems transport glacially derived sediment across the continental margin into Surveyor Channel, an abyssal fan and channel system that reaches over 1,000 km to the Aleutian Trench.

Structure of the North American Atlantic Continental Margin

USGS Publications Warehouse

Schlee, J.S.; Klitgord, K.K.

1986-01-01

Off E N America, where the structure of the continental margin is essentially constructional, seismic profiles have approximated geologic cross sections up to 10-15km below the sea floor and revealed major structural and stratigraphic features that have regional hydrocarbon potential. These features include a) a block-faulted basement hinge zone; b) a deep, broad, rifted basement filled with clastic sediment and salt; and c) a buried paleoshelf-edge complex that has many forms. The mapping of seismostratigraphic units over the continental shelf, slope, and rise has shown that the margin's developmental state included infilling of a rifted margin, buildup of a carbonate platform, and construction of an onlapping continental-rise wedge that was accompanied by erosion of the slope. -from Authors

Frontal belt curvature and oblique ramp development at an obliquely collided irregular margin: Geometry and kinematics of the NW Taiwan fold-thrust belt

NASA Astrophysics Data System (ADS)

Lacombe, Olivier; Mouthereau, FréDéRic; Angelier, Jacques; Chu, Hao-Tsu; Lee, Jian-Cheng

2003-06-01

Combined structural and tectonic analyses demonstrate that the NW Foothills of the Taiwan collision belt constitute mainly an asymmetric "primary arc" type fold-thrust belt. The arcuate belt developed as a basin-controlled salient in the portion of the foreland basin that was initially thicker, due to the presence of a precollisional depocenter (the Taihsi basin). Additional but limited buttress effects at end points related to interaction with foreland basement highs (Kuanyin and Peikang highs) may have also slightly enhanced curvature. The complex structural pattern results from the interaction between low-angle thrusting related to shallow decollement tectonics and oblique inversion of extensional structures of the margin on the southern edge of the Kuanyin basement high. The tectonic regimes and mechanisms revealed by the pattern of paleostress indicators such as striated outcrop-scale faults are combined with the orientation and geometry of offshore and onshore regional faults in order to accurately define the Quaternary kinematics of the propagating units. The kinematics of this curved range is mainly controlled by distributed transpressional wrenching along the southern edge of the Kuanyin high, leading to the development of a regional-scale oblique ramp, the Kuanyin transfer fault zone, which is conjugate of the NW trending Pakua transfer fault zone north of the Peikang basement high. The divergence between the N120° regional transport direction and the maximum compressive trend that evolved from N120° to N150° (and even to N-S) in the northern part of the arc effectively supports distributed wrench deformation along its northern limb during the Pleistocene. The geometry and kinematics of the western Taiwan Foothills therefore appear to be highly influenced by both the preorogenic structural pattern of the irregularly shaped Chinese passive margin and the obliquity of its Plio-Quaternary collision with the Philippine Sea plate.

Neotectonics of Asia: Thin-shell finite-element models with faults

NASA Technical Reports Server (NTRS)

Kong, Xianghong; Bird, Peter

1994-01-01

As India pushed into and beneath the south margin of Asia in Cenozoic time, it added a great volume of crust, which may have been (1) emplaced locally beneath Tibet, (2) distributed as regional crustal thickening of Asia, (3) converted to mantle eclogite by high-pressure metamorphism, or (4) extruded eastward to increase the area of Asia. The amount of eastward extrusion is especially controversial: plane-stress computer models of finite strain in a continuum lithosphere show minimal escape, while laboratory and theoretical plane-strain models of finite strain in a faulted lithosphere show escape as the dominant mode. We suggest computing the present (or neo)tectonics by use of the known fault network and available data on fault activity, geodesy, and stress to select the best model. We apply a new thin-shell method which can represent a faulted lithosphere of realistic rheology on a sphere, and provided predictions of present velocities, fault slip rates, and stresses for various trial rheologies and boundary conditions. To minimize artificial boundaries, the models include all of Asia east of 40 deg E and span 100 deg on the globe. The primary unknowns are the friction coefficient of faults within Asia and the amounts of shear traction applied to Asia in the Himalayan and oceanic subduction zones at its margins. Data on Quaternary fault activity prove to be most useful in rating the models. Best results are obtained with a very low fault friction of 0.085. This major heterogeneity shows that unfaulted continum models cannot be expected to give accurate simulations of the orogeny. But, even with such weak faults, only a fraction of the internal deformation is expressed as fault slip; this means that rigid microplate models cannot represent the kinematics either. A universal feature of the better models is that eastern China and southeast Asia flow rapidly eastward with respect to Siberia. The rate of escape is very sensitive to the level of shear traction in the Pacific subduction zones, which is below 6 MPa. Because this flow occurs across a wide range of latitudes, the net eastward escape is greater than the rate of crustal addition in the Himalaya. The crustal budget is balanced by extension and thinning, primarily within the Tibetan plateau and the Baikal rift. The low level of deviation stresses in the best models suggests that topographic stress plays a major role in the orogeny; thus, we have to expect that different topography in the past may have been linked with fundamentally different modes of continental collision.

Fortnightly modulation of San Andreas tremor and low-frequency earthquakes

DOE Office of Scientific and Technical Information (OSTI.GOV)

van der Elst, Nicholas J.; Delorey, Andrew A.; Shelly, David R.

Earth tides modulate tremor and low-frequency earthquakes (LFEs) on faults in the vicinity of the brittle-ductile (seismic-aseismic) transition. Our response to the tidal stress carries otherwise inaccessible information about fault strength and rheology. We analyze the LFE response to the fortnightly tide, which modulates the amplitude of the daily tidal stress over a 14-d cycle. LFE rate is highest during the waxing fortnightly tide, with LFEs most strongly promoted when the daily stress exceeds the previous peak stress by the widest margin. This pattern implies a threshold failure process, with slip initiated when stress exceeds the local fault strength. Furthermore,more » variations in sensitivity to the fortnightly modulation may reflect the degree of stress concentration on LFE-producing brittle asperities embedded within an otherwise aseismic fault.« less

Fortnightly modulation of San Andreas tremor and low-frequency earthquakes

DOE PAGES

van der Elst, Nicholas J.; Delorey, Andrew A.; Shelly, David R.; ...

2016-07-18

Earth tides modulate tremor and low-frequency earthquakes (LFEs) on faults in the vicinity of the brittle-ductile (seismic-aseismic) transition. Our response to the tidal stress carries otherwise inaccessible information about fault strength and rheology. We analyze the LFE response to the fortnightly tide, which modulates the amplitude of the daily tidal stress over a 14-d cycle. LFE rate is highest during the waxing fortnightly tide, with LFEs most strongly promoted when the daily stress exceeds the previous peak stress by the widest margin. This pattern implies a threshold failure process, with slip initiated when stress exceeds the local fault strength. Furthermore,more » variations in sensitivity to the fortnightly modulation may reflect the degree of stress concentration on LFE-producing brittle asperities embedded within an otherwise aseismic fault.« less

Composite transform-convergent plate boundaries: description and discussion

USGS Publications Warehouse

Ryan, H.F.; Coleman, P.J.

1992-01-01

The leading edge of the overriding plate at an obliquely convergent boundary is commonly sliced by a system of strike-slip faults. This fault system is often structurally complex, and may show correspondingly uneven strain effects, with great vertical and translational shifts of the component blocks of the fault system. The stress pattern and strain effects vary along the length of the system and change through time. These margins are considered to be composite transform-convergent (CTC) plate boundaries. Examples are given of structures formed along three CTC boundaries: the Aleutian Ridge, the Solomon Islands, and the Philippines. The dynamism of the fault system along a CTC boundary can enhance vertical tectonism and basin formation. This concept provides a framework for the evaluation of petroleum resources related to basin formation, and mineral exploration related to igneous activity associated with transtensional processes. ?? 1992.

Dissipated energy as a design parameter of coated conductors for their use in resistive fault current limiters

NASA Astrophysics Data System (ADS)

Schacherer, C.; Kudymow, A.; Noe, M.

2008-02-01

Coated conductors are suitable for many power applications like motors, magnets and superconducting fault current limiters (SCFCLs). For their use in resistive SCFCLs main requirements are quench stability and resistance development above Tc. Several coated conductors are available with different kinds of stabilization like thickness or material of cap-layer and additional stabilization. The stabilization can vary and has a great influence on the quench stability and quench behaviour of a coated conductor. Thus, for the dimensioning of a superconducting current limiting element there is a need of reliable and universal design parameters. This paper presents experimental quench test results on several coated conductor types with different stabilization and geometry. The test results show that the dissipated energy during a quench is a very useful parameter for the SCFCL design.

Extensional crustal tectonics and crust-mantle coupling, a view from the geological record

NASA Astrophysics Data System (ADS)

Jolivet, Laurent; Menant, Armel; Clerc, Camille; Sternai, Pietro; Ringenbach, Jean-Claude; Bellahsen, Nicolas; Leroy, Sylvie; Faccenna, Claudio; Gorini, Christian

2017-04-01

In passive margins or back-arc regions, extensional deformation is often asymmetric, i.e. normal faults or extensional ductile shear zones dip in the same direction over large distances. We examine a number of geological examples in convergent or divergent contexts suggesting that this asymmetry results from a coupling between asthenospheric flow and crustal deformation. This is the case of the Mediterranean back-arc basins, such as the Aegean Sea, the northern Tyrrhenian Sea, the Alboran domain or the Gulf of Lion passive margin. Similar types of observation can be made on some of the Atlantic volcanic passive margins and the Afar region, which were all formed above a mantle plume. We discuss these contexts and search for the main controlling parameters for this asymmetric distributed deformation that imply a simple shear component at the scale of the lithosphere. The different geodynamic settings and tectonic histories of these different examples provide natural case-studies of the different controlling parameters, including a pre-existing heterogeneity of the crust and lithosphere (tectonic heritage) and the possible contribution of the underlying asthenospheric flow through basal drag or basal push. We show that mantle flow can induce deformation in the overlying crust in case of high heat flow and thin lithosphere. In back-arc regions, the cause of asymmetry resides in the relative motion between the asthenosphere below the overriding plate and the crust. When convergence and slab retreat work concurrently the asthenosphere flows faster than the crust toward the trench and the sense of shear is toward the upper plate. When slab retreat is the only cause of subduction, the sense of shear is opposite. In both cases, mantle flow is mostly the consequence of slab retreat and convergence. Mantle flow can however result also from larger-scale convection, controlling rifting dynamics prior to the formation of oceanic crust. In volcanic passive margins, in most cases normal faults dip toward the continent. This asymmetry may either result from the mantle flowing underneath regions evolving above a migrating plume, such as the Afar, when an asymmetry is observed at the scale of the rift, or from necking of the lithosphere when the conjugate margins show an opposite asymmetry. We summarize the various observed situations with normal faults dipping toward the continent ("hot" margins) or toward the ocean ("cold" margins) and discuss whether mantle flow is responsible for the observed asymmetry of deformation or not. Slipping along pre-existing heterogeneities seems a second-order phenomenon at lithospheric or crustal scale, except at the initiation of rifting.

Dynamic topography of the southern Central Anatolian Plateau, Turkey, and geodynamic driving mechanisms

NASA Astrophysics Data System (ADS)

Schildgen, T. F.; Cosentino, D.; Dudas, F. O.; Niedermann, S.; Strecker, M. R.; Echler, H.; Yildirim, C.

2010-12-01

Collision between Eurasia and Arabia and subsequent westward extrusion of the Anatolian microplate explains the development of major intracontinental fault systems in Anatolia that have remained active to the present-day. Concurrent, and probable episodic uplift of the Central and Eastern Anatolian plateaus (CAP and EAP), however, suggests that additional geodynamic mechanisms have contributed to the late Cenozoic morphologic development of the region. Sedimentary basins spanning the southern margin of the CAP provide insights on the timing and rates of different phases of surface uplift, giving constraints to test which geodynamic processes have contributed to surface uplift, orogenic plateau growth, and coupled landscape/climate evolution. Stratigraphic and geomorphic records of uplift and subsidence in the Mut Basin at the southern CAP margin and along the Göksu River record dynamic topographic development. Biostratigraphy and Sr isotope stratigraphy on the highest (ca. 2 km) uplifted marine sediments of the Mut basin furnish a maximum age of ca. 8 Ma for the onset of late Cenozoic uplift of the region. A Pliocene to early Pleistocene marine section, inset within the older stratigraphy at ca. 0.2 to 1.2 km elevation, reveals a history of subsidence and renewed uplift, following the initial uplift that occurred between ca. 8 Ma and Pliocene time. The most recent phase of uplift continued with possibly minor interruptions during the Quaternary, and is recorded by a series of fluvial terraces preserved between 30 and 143 m above the modern Göksu River. One terrace (143 m) reveals a 21Ne model exposure age of ca. 160 ka; ongoing exposure age determination will further constrain the uplift history. Different geodynamic mechanisms have likely contributed to surface uplift along the southern CAP margin. Initial uplift may have been associated with the predominantly sinistral Ecemis fault system that spans the southern and southeastern CAP margin. Neogene counter-clockwise rotation of Central Anatolia and changes in regional fault kinematics, which likely caused local compression along structures with previous sinistral strike-slip kinematics, may have contributed to early deformation and uplift of the region. Our stratigraphic and field data, together with regional geophysical anomalies, suggest that more recent uplift may be related to upwelling asthenosphere through a slab window, which formed when the initial slab detachment associated with the Bitlis-Zagros collision zone (southern margin of the EAP) propagated to the southwest. The intervening Pliocene to early Pleistocene subsidence was likely related to E-W stretching of the southern margin, possibly driven by oroclinal bending of the margin.

The Role of Magma During Continent-Ocean Transition

NASA Astrophysics Data System (ADS)

Bastow, Ian; Keir, Derek; Rooney, Tyrone; Kendall, J.-Michael

2010-05-01

Passive margins worldwide are often considered magmatic because they are characterised by thick sequences of extrusive and intrusive igneous rocks emplaced around the time of continental breakup. Despite the global abundance of such margins, however, it is difficult to discriminate between different models of both extension and melt generation, since most ruptured during Gondwana breakup >100Ma and the continent-ocean transition (COT) is now hidden by thick, basaltic seaward dipping reflectors (SDRs). These margins are no longer tectonically active so the roles of faulting, stretching and magma intrusion in accommodating extension, and timing of SDRs emplacement during rift evolution have to be inferred from rifting models or from the geological record preserved at the fully developed passive margin. Similarly mantle processes during COT development have long since ceased, so whether breakup was characterized by broad thermal upwelling, small-scale convection or a fertile geoscientific mantle remains ambiguous. The East African rift in Ethiopia offers a unique opportunity to address all these problems because south-to-north it exposes subaerially the transition from continental rifting and incipient sea-floor spreading within a young flood basalt province. Here we present a suite of geophysical and geochemical observations from Ethiopia that document the significance of magma intrusion and extrusion as rifting evolves from an initially broad zone of stretching and faulting to a narrower axial graben in which magma injection dominates strain.

Unfolding the arc: The use of pre-orogenic constraints to assess the evolution of the Variscan belt in Western Europe

NASA Astrophysics Data System (ADS)

Casas, Josep M.; Brendan Murphy, J.

2018-06-01

We present a pre-orogenic, early Paleozoic, palinspastic reconstruction of the northern Gondwana margin that was subsequently involved in the Late Paleozoic Variscan orogeny in central and Western Europe. Our reconstruction is based on two pre-orogenic data sets, the age and distribution of Cambrian-Ordovician magmatism and the detrital zircon age signature of late Neoproterozoic-early Paleozoic clastic rocks. We obtain this reconstruction by unfolding the Ibero-Armorican arc and by restoring the movement of the large-scale dextral strike-slip faults that transect the different tectono-stratigraphic units. Our results favour an irregular shape for this part of the northern Gondwana margin with a N-S central segment linking two E-W oriented segments. The proposed reconstruction and the structural restoration of the main features of Variscan deformation is in accordance with some aspects of previously proposed structural models, such as the curved geometry of the Gondwanan margin required by the indentor model for continental collision, the role played by the large strike-slip faults in dispersing formerly juxtaposed units, and the regional-scale oroclinal folding of part of this margin during late Carboniferous-Early Permian times. The combined use of the pre-orogenic geological constraints and palinspastic restoration is a useful approach that may provide a foundation for continual refinement of reconstructions as more data become available.

Evidence for Active Westward Tilting of Fortymile Wash, Nye County, Nevada

NASA Astrophysics Data System (ADS)

McKague, H. L.; Sims, D. W.; Waiting, D. J.

2006-12-01

Fortymile Wash is located east and south of a potential high-level nuclear waste repository at Yucca Mountain, Nevada. Several lines of evidence suggest that this may be an area of active westward tilting associated with the continued development of Crater Flat basin and slip on the Bare Mountain normal fault. Near the southern end of Busted Butte, the incised channel of Fortymile Wash changes trend downgradient from south to south-southwest. Further southward, the incised main channel grades to a divergent distributary channel system that shows evidence of increasingly westward tilt. Viewed in profiles oriented normal to the incised channel and across the Fortymile Wash distributary system, topographic elevation of the western margin of the fan decreases southward, resulting in the elevation of the western margin of Fortymile Basin being as much as 18 m [59 ft] lower than the channel system on the eastern fan margin. Mapping of the surficial deposits within the distributary channel system (Pelletier, et al., 2005; Geophy. Res. Ltr., Vol. 32) may be interpreted to show a westward shift (downslope) of the locus of erosional activity toward the topographically lower western fan margin. Most of the older alluvium (Qa3 {86±40-16 ka}) has been eroded from the eastern portion, while incipient incision into the older alluvium is occurring on the western side of the distributary channel system. The results from level-line benchmark surveys (Gilmore, 1992; USGS OFR 92- 450) from 1915 and 1984 show gradual and systematic elevation changes east of the Bare Mountain fault to just east of Amargosa City, Nevada, where a step-like increase occurs. The level-line surveys are near and along the path of U.S. Highway 95, which traverses the distributary channel system of the Fortymile Wash alluvial fan in the southern portion of the Fortymile Wash basin. These lines of evidence indicate disequilibrium in the channel system that would result from active westward tilting of the Fortymile Wash basin. The active tilting in Fortymile Wash may be associated with continued development of Crater Flat basin and slip on the Bare Mountain fault, with the steeply dipping southern segment of the Bare Mountain fault not only controlling the southward-increasing subsidence in Southern Crater Flat, but also the changes observed in the southern Fortymile Wash basin 20 km [12.5 mi] to the southeast. An alternative interpretation is westward tilting, which is the result of active, but not evident, faulting beneath or near Fortymile Wash. Additional evidence indicating the presence of a fault beneath Fortymile Wash is the easterly dip of Miocene tuffs in Fran Ridge north of Busted Butte. This abstract is an independent product of the Center for Nuclear Waste Regulatory Analyses and does not necessarily reflect the view or regulatory position of the U.S. Nuclear Regulatory Commission.

Interaction of the subduction process and forearc tectonics: An example from the active N - Chilean margin

NASA Astrophysics Data System (ADS)

Victor, P.; Sobiesiak, M.

2005-12-01

Convergent plate boundaries at continental margins belong to the tectonically most active areas on earth and are endangered by devastating earthquakes and tsunamis. The north Chilean margin is a high strain continental margin driven by fast plate convergence rate. The greatest amount of strain is accommodated along the subduction interface. Nevertheless there is extensive crustal deformation obvious by surface ruptures along reactivated segments of large fault systems and vertical surface motions reflecting the interaction between subducting and overriding plates. The historical seismicity record indicates that great earthquakes affect the Chilean Forearc with recurrence intervals of about 112+/- 21 y . The last great event in northern Chile occurred in 1995 near Antofagasta. The Mw= 8.0 event ruptured the subduction interface 180 km along strike with an average slip of about 5m in the depth interval between 10-50 km. From careful evaluation of the aftershock sequence by examining the different catagories of aftershock focal mechanisms we can define three segments of the seismogenic zone affected by the Antofagasta main shock. The non-ruptured northern segment beneath Mejillones Peninsula is seperated by a broad transition zone from the central segment which hosts the earthquakes' rupture plane. The southern fault plane boundary is identified by linear alignment of all apparent aftershock mechanisms. Along this southern boundary the strike slip mechanisms are exclusively left lateral whereas the strike slip mechanisms along the northern transition zone are right lateral. The orientations of summed moment tensors calculated from aftershock fault plane solutions on the northern segment and in the northern transition zone differ from the orientations exhibited by moment tensors on the central segment. This might indicate a rotational component in the coseismic movement of the ruptured segment relative to the non-ruptured segment. The observed segmentation of the downgoing plate correlates well with changes in the coseismic surface displacement field and coseismic rotations derived from GPS data (Allmendinger et al. in press). We can localize a transition zone at Mejillones peninsula (23,5°S) striking approximately N 80°E dominated by clockwise vertical axis rotations also marked by rotations of the summed moment tensors on the downgoing plate. The calculated strain tensor for this transition zone does not correspond with long term surface deformation, implying that coseismic as well as early postseismic effects on the subduction interface do not contribute to long term deformation of crustal fault zones. The Antofagasta earthquake took place just south of the large 1877 gap which extends from southern Peru to Mejillones Peninsula, being the surface expression of a barrier seperating the Antofagasta fault plane from the expected future fault plane. From our studies of the Antofagasta subduction zone and the surface displacement field we hope to find evidences for interface-crust-surface interactions which can be extrapolated also to the 1877 gap.

Neogene Development of the Terror Rift, western Ross Sea, Antarctica

NASA Astrophysics Data System (ADS)

Sauli, C.; Sorlien, C. C.; Busetti, M.; De Santis, L.; Wardell, N.; Henrys, S. A.; Geletti, R.; Wilson, T. J.; Luyendyk, B. P.

2015-12-01

Terror Rift is a >300 km-long, 50-70 km-wide, 14 km-deep sedimentary basin at the edge of the West Antarctic Rift System, adjacent to the Transantarctic Mountains. It is cut into the broader Victoria Land Basin (VLB). The VLB experienced 100 km of mid-Cenozoic extension associated with larger sea floor spreading farther north. The post-spreading (Neogene) development of Terror Rift is not well understood, in part because of past use of different stratigraphic age models. We use the new Rossmap seismic stratigraphy correlated to Cape Roberts and Andrill cores in the west and to DSDP cores in the distant East. This stratigraphy, and new fault interpretations, was developed using different resolutions of seismic reflection data included those available from the Seismic Data Library System. Depth conversion used a new 3D velocity model. A 29 Ma horizon is as deep as 8 km in the south, and a 19 Ma horizon is >5 km deep there and 4 km-deep 100 km farther north. There is a shallower northern part of Terror Rift misaligned with the southern basin across a 50 km right double bend. It is bounded by steep N-S faults down-dropping towards the basin axis. Between Cape Roberts and Ross Island, the Oligocene section is also progressively-tilted. This Oligocene section is not imaged within northern Terror Rift, but the simplest hypothesis is that some of the Terror Rift-bounding faults were active at least during Oligocene through Quaternary time. Many faults are normal separation, but some are locally vertical or even reverse-separation in the upper couple of km. However, much of the vertical relief of the strata is due to progressive tilting (horizontal axis rotation) and not by shallow faulting. Along the trend of the basin, the relief alternates between tilting and faulting, with a tilting margin facing a faulted margin across the Rift, forming asymmetric basins. Connecting faults across the basin form an accommodation zone similar to other oblique rifts. The Neogene basin is shallow to non-existent 300 km north of Ross Island, near -74° 30' latitude. We propose that the Neogene history of Terror Rift has been highly-oblique right-lateral, terminating northward into right lateral faults of northern Victoria Land.

The impact of geological storage of CO2 on the mechanical behaviour of faults - Can we predict frictional strength and stability?

NASA Astrophysics Data System (ADS)

Bakker, Elisenda; Hangx, Suzanne J. T.; Spiers, Christopher J.

2013-04-01

CO2 storage in depleted oil and gas reservoirs is seen as an important climate change mitigation strategy. In order to evaluate storage integrity of the reservoir-caprock system, potential leakage pathways, such as pre-existing or induced faults, need to be investigated. The mechanical and transport properties of intact and fractured rock may be affected by both short and long-term (> 100 years) fluid-rock interactions. In practice, chemical interactions that occur on timescales longer than a few months are too slow and difficult to reproduce in laboratory experiments. Recently, research within the CCS community has steered towards investigating the effect of CO2 on fault stability and particularly towards induced seismicity. In this context, we performed a variety of mechanical tests on rock types relevant for CCS sites, with the aim of investigating the effect of CO2/brine/rock interactions on the mechanical and transport properties of faults. To this end, we used both CO2-exposed and unaltered rocks obtained from sandstone reservoirs of natural CO2 fields located at Green River (Utah, USA) and Werkendam (The Netherlands). Two main types of experiment were performed: 1) triaxial tests in which cylindrical samples were shear fractured, studying subsequent slip on the fault, and 2) direct shear tests performed on (simulated) fault gouge prepared by crushing intact rock. Our results showed that the frictional stability of fault gouges is largely controlled by factors such as mineralogical composition, notably carbonate content, and temperature. We have placed our results in the context of the large body of data that already exists on fault gouge friction behaviour. The combined body of work encompasses materials ranging from clay-quartz mixtures, to anhydrite and carbonate rocks, all of which are relevant rock types for CCS. In this way, we delineate the knowledge gaps that still exist, and we show how the available data can be used to make preliminary predictions on fault friction behaviour and (micro)seismic fault reactivation potential in geological CO2-storage systems.

A new view for the geodynamics of Ecuador: Implication in seismogenic source definition and seismic hazard assessment

NASA Astrophysics Data System (ADS)

Yepes, Hugo; Audin, Laurence; Alvarado, Alexandra; Beauval, Céline; Aguilar, Jorge; Font, Yvonne; Cotton, Fabrice

2016-05-01

A new view of Ecuador's complex geodynamics has been developed in the course of modeling seismic source zones for probabilistic seismic hazard analysis. This study focuses on two aspects of the plates' interaction at a continental scale: (a) age-related differences in rheology between Farallon and Nazca plates—marked by the Grijalva rifted margin and its inland projection—as they subduct underneath central Ecuador, and (b) the rapidly changing convergence obliquity resulting from the convex shape of the South American northwestern continental margin. Both conditions satisfactorily explain several characteristics of the observed seismicity and of the interseismic coupling. Intermediate-depth seismicity reveals a severe flexure in the Farallon slab as it dips and contorts at depth, originating the El Puyo seismic cluster. The two slabs position and geometry below continental Ecuador also correlate with surface expressions observable in the local and regional geology and tectonics. The interseismic coupling is weak and shallow south of the Grijalva rifted margin and increases northward, with a heterogeneous pattern locally associated to the Carnegie ridge subduction. High convergence obliquity is responsible for the North Andean Block northeastward movement along localized fault systems. The Cosanga and Pallatanga fault segments of the North Andean Block-South American boundary concentrate most of the seismic moment release in continental Ecuador. Other inner block faults located along the western border of the inter-Andean Depression also show a high rate of moderate-size earthquake production. Finally, a total of 19 seismic source zones were modeled in accordance with the proposed geodynamic and neotectonic scheme.

Constraining the Distribution of Vertical Slip on the South Heli Shan Fault (Northeastern Tibet) From High-Resolution Topographic Data

NASA Astrophysics Data System (ADS)

Bi, Haiyun; Zheng, Wenjun; Ge, Weipeng; Zhang, Peizhen; Zeng, Jiangyuan; Yu, Jingxing

2018-03-01

Reconstruction of the along-fault slip distribution provides an insight into the long-term rupture patterns of a fault, thereby enabling more accurate assessment of its future behavior. The increasing wealth of high-resolution topographic data, such as Light Detection and Ranging and photogrammetric digital elevation models, allows us to better constrain the slip distribution, thus greatly improving our understanding of fault behavior. The South Heli Shan Fault is a major active fault on the northeastern margin of the Tibetan Plateau. In this study, we built a 2 m resolution digital elevation model of the South Heli Shan Fault based on high-resolution GeoEye-1 stereo satellite imagery and then measured 302 vertical displacements along the fault, which increased the measurement density of previous field surveys by a factor of nearly 5. The cumulative displacements show an asymmetric distribution along the fault, comprising three major segments. An increasing trend from west to east indicates that the fault has likely propagated westward over its lifetime. The topographic relief of Heli Shan shows an asymmetry similar to the measured cumulative slip distribution, suggesting that the uplift of Heli Shan may result mainly from the long-term activity of the South Heli Shan Fault. Furthermore, the cumulative displacements divide into discrete clusters along the fault, indicating that the fault has ruptured in several large earthquakes. By constraining the slip-length distribution of each rupture, we found that the events do not support a characteristic recurrence model for the fault.

Did the Malaysian Main Range record a weak hot Mega Shear?

NASA Astrophysics Data System (ADS)

Sautter, Benjamin; Pubellier, Manuel

2015-04-01

The Main Range of Peninsular Malaysia is a batholith that extends over more than 500km from Malacca in the South to the Thailand border in the North. It results from the subduction/accretion history of the western margin of Sunda Plate by Late Triassic times. We present a structural analysis based on geomorphology, field observations and geochronological data. While most of the basement fabrics are characterized by N-S structures such as granitic plutons, sutures, and folds, a prominent oblique deformation occurred by the End of the Mesozoics synchronous with a widespread thermal anomaly (eg Tioman, Stong, Gunung Jerai, Khanom, Krabi plutons). Morphostructures and drainage anomalies from Digital Elevation Model (SRTM and ASTER), allow us to highlight 2 major groups of penetrative faults in the Central Range Batholith: early NW-SE (5km spaced faults some of which are identified as thrust faults) cross-cut and offset by NNE-SSW dextral normal faults. The regularly spaced NW-SE faults bend toward the flanks of the Batholith and tend to parallel both the Bentong Raub Suture Zone to the East and the strike slip Bok Bak Fault to the West, thus giving the overall fault network the aspect of a large C/S band. Hence, a ductile/brittle behavior can be proposed for the sigmoid faults in the core of the Batholith, whereas the NNE faults are clearly brittle, more linear and are found on the smaller outlying plutons. Radiogenic crystallization ages are homogenous at 190±20Ma (U-Pb Zircon, Tc>1000°C and K-Ar Muscovite, Tc350°C) whereas Zircon fission tracks(Tc=250°C) show specific spatial zoning of the data distribution with ages at 100±10Ma for the outlying plutons and ages at 70±10Ma for the Main Range. We propose a structural mechanism according to which the Main Range would be the ductile core of a Mega-Shear Zone exhumed via transpressive tectonics by the end of Mesozoic Times. A first stage between 100 and 70Ma (Upper Cretaceous) of dextral transpression affected Peninsular Malaysia at a lithospheric scale, accommodated by N-S faults (C planes) such as the Bentong Raub Suture Zone, the Bukit Tinggi fault and the Kledang Fault. This lead to the formation of NW-SE fractures in already exhumed peripheral plutons (< 250°C) and deep level (> 250°C) sigmoid faults (S planes) in the Main range. Later a brittle stage of exhumation occurred in the same system, after 70Ma, leading to NNE-SSW dextral Riedel type faults reactivating pluton flanks, and offsetting older faults as well as quartz dykes. The occurrence of such a structure could be linked to the subduction of the Wharton Ridge at the western margin of Sunda Plate. As a result, a collapse of this hot and thin crust occurred accommodated by LANF's reactivating the basement fabrics including intrusive edges and folds hinges.

Bayesian estimation of source parameters and associated Coulomb failure stress changes for the 2005 Fukuoka (Japan) Earthquake

NASA Astrophysics Data System (ADS)

Dutta, Rishabh; Jónsson, Sigurjón; Wang, Teng; Vasyura-Bathke, Hannes

2018-04-01

Several researchers have studied the source parameters of the 2005 Fukuoka (northwestern Kyushu Island, Japan) earthquake (Mw 6.6) using teleseismic, strong motion and geodetic data. However, in all previous studies, errors of the estimated fault solutions have been neglected, making it impossible to assess the reliability of the reported solutions. We use Bayesian inference to estimate the location, geometry and slip parameters of the fault and their uncertainties using Interferometric Synthetic Aperture Radar and Global Positioning System data. The offshore location of the earthquake makes the fault parameter estimation challenging, with geodetic data coverage mostly to the southeast of the earthquake. To constrain the fault parameters, we use a priori constraints on the magnitude of the earthquake and the location of the fault with respect to the aftershock distribution and find that the estimated fault slip ranges from 1.5 to 2.5 m with decreasing probability. The marginal distributions of the source parameters show that the location of the western end of the fault is poorly constrained by the data whereas that of the eastern end, located closer to the shore, is better resolved. We propagate the uncertainties of the fault model and calculate the variability of Coulomb failure stress changes for the nearby Kego fault, located directly below Fukuoka city, showing that the main shock increased stress on the fault and brought it closer to failure.

Does permanent extensional deformation in lower forearc slopes indicate shallow plate-boundary rupture?

NASA Astrophysics Data System (ADS)

Geersen, J.; Ranero, C. R.; Kopp, H.; Behrmann, J. H.; Lange, D.; Klaucke, I.; Barrientos, S.; Diaz-Naveas, J.; Barckhausen, U.; Reichert, C.

2018-05-01

Seismic rupture of the shallow plate-boundary can result in large tsunamis with tragic socio-economic consequences, as exemplified by the 2011 Tohoku-Oki earthquake. To better understand the processes involved in shallow earthquake rupture in seismic gaps (where megathrust earthquakes are expected), and investigate the tsunami hazard, it is important to assess whether the region experienced shallow earthquake rupture in the past. However, there are currently no established methods to elucidate whether a margin segment has repeatedly experienced shallow earthquake rupture, with the exception of mechanical studies on subducted fault-rocks. Here we combine new swath bathymetric data, unpublished seismic reflection images, and inter-seismic seismicity to evaluate if the pattern of permanent deformation in the marine forearc of the Northern Chile seismic gap allows inferences on past earthquake behavior. While the tectonic configuration of the middle and upper slope remains similar over hundreds of kilometers along the North Chilean margin, we document permanent extensional deformation of the lower slope localized to the region 20.8°S-22°S. Critical taper analyses, the comparison of permanent deformation to inter-seismic seismicity and plate-coupling models, as well as recent observations from other subduction-zones, including the area that ruptured during the 2011 Tohoku-Oki earthquake, suggest that the normal faults at the lower slope may have resulted from shallow, possibly near-trench breaking earthquake ruptures in the past. In the adjacent margin segments, the 1995 Antofagasta, 2007 Tocopilla, and 2014 Iquique earthquakes were limited to the middle and upper-slope and the terrestrial forearc, and so are upper-plate normal faults. Our findings suggest a seismo-tectonic segmentation of the North Chilean margin that seems to be stable over multiple earthquake cycles. If our interpretations are correct, they indicate a high tsunami hazard posed by the yet un-ruptured southern segment of the seismic gap.

Incorporating Cutting Edge Scientific Results from the Margins-Geoprisms Program into the Undergraduate Curriculum, Rupturing Continental Lithosphere Part I: Introducing Seismic Interpretation and Isostasy Principles Using Gulf of California Examples

NASA Astrophysics Data System (ADS)

Lamb, M. A.; Cashman, S. M.; Dorsey, R. J.; Bennett, S. E. K.; Loveless, J. P.; Goodliffe, A. M.

2014-12-01

The NSF-MARGINS Program funded a decade of research on continental margin processes. The NSF-GeoPRISMS Mini-lesson Project, funded by NSF-TUES, is designed to integrate the significant findings from the MARGINS program into open-source college-level curriculum. The Gulf of California (GOC) served as the focus site for the Rupturing Continental Lithosphere initiative, which addressed several scientific questions: What forces drive rift initiation, localization, propagation and evolution? How does deformation vary in time and space, and why? How does crust evolve, physically and chemically, as rifting proceeds to sea-floor spreading? What is the role of sedimentation and magmatism in continental extension? We developed two weeks of curriculum designed for an upper-division structural geology, tectonics or geophysics course. The curriculum includes lectures, labs, and in-class activities that can be used as a whole or individually. The first set of materials introduces the RCL initiative to students and has them analyze the bathymetry and oblique-rifting geometry of the GOC in an exercise using GeoMapApp. The second set of materials has two goals: (1) introduce students to fundamental concepts of interpreting seismic reflection data via lectures and in-class interpretation of strata, basement, and faults from recent GOC seismic data, and (2) encourage students to discover the structural geometry and rift evolution, including the east-to-west progression of faulting and transition from detachment to high-angle faulting in the northern GOC, and changes in deformation style from north to south. In the third set of materials, students investigate isostatic affects of sediment fill in GOC oblique rift basins. This activity consists of a problem set, introduced in a lecture, where students integrate their findings from the previous bathymetry- and seismic-interpretation exercises.

Aspect ratio effects on neoclassical tearing modes from comparison between DIII-D and National Spherical Torus Experiment

DOE Office of Scientific and Technical Information (OSTI.GOV)

La Haye, R. J.; Buttery, R. J.; Gerhardt, S. P.

Neoclassical tearing mode islands are sustained by helically perturbed bootstrap currents arising at finite beta from toroidal effects that trap a fraction of the particles in non-circulating orbits. DIII-D and NSTX are here operated with similar shape and cross-sectional area but almost a factor of two difference in inverse aspect ratio a/R. In these experiments, destabilized n=1 tearing modes were self-stabilized (reached the 'marginal point') by reducing neutral-beam power and thus beta. The measure of the marginal island gives information on the small-island stabilizing physics that in part (with seeding) governs onset. The marginal island width on NSTX is foundmore » to be about three times the ion banana width and agrees with that measured in DIII-D, except for DIII-D modes closer to the magnetic axis, which are about two times the ion banana width. There is a balance of the helically perturbed bootstrap term with small island effects with the sum of the classical and curvature terms in the modified Rutherford equation for tearing-mode stability at the experimental marginal point. Empirical evaluation of this sum indicates that while the stabilizing effect of the curvature term is negligible in DIII-D, it is important in NSTX. The mode temporal behavior from the start of neutral-beam injection reduction also suggests that NSTX operates closer to marginal classical tearing stability; this explains why there is little hysteresis in beta between mode onset, saturation, and self-stabilization (while DIII-D has large hysteresis in beta). NIMROD code module component calculations based on DIII-D and NSTX reconstructed experimental equilibria are used to diagnose and confirm the relative importance of the stabilizing curvature effect, an advantage for low aspect ratio; the relatively greater curvature effect makes for less susceptibility to NTM onset even if the classical tearing stability index is near marginal.« less

Miocene to present-day shortening and intermontane basin formation in the Andean Puna Plateau, NW Argentina (24°30'S)

NASA Astrophysics Data System (ADS)

Strecker, M. R.; Bookhagen, B.; Alonso, R. N.; Pingel, H.; Freymark, J.

2015-12-01

With average elevations of about 3.7 km the Altiplano-Puna Plateau of the southern central Andes constitutes the world's second largest orogenic plateau. The plateau generally consists of internally drained, partly coalesced sedimentary basins bordered by reverse-fault bounded ranges, >5 km high. In the Puna, the Argentine sector of the plateau, active tectonism has been interpreted to be characterized by a low level of strike-slip and normal faulting associated with mafic volcanism. In contrast, the eastern plateau margins and the adjacent foreland record a higher level of seismicity and ongoing contraction. Despite ubiquitous Plio-Pleistocene normal faulting along the eastern plateau margins, our new observations record contraction in the plateau interior. Fanning of E-dipping Miocene sedimentary strata involved in the formation of an anticline in the Pocitos Basin of the central Puna interior indicates growth, which must have begun after 7 Ma; 1.5-m.y.-old lacustrine strata as well as tilted Pleistocene lacustrine shorelines associated with this structure indicate sustained uplift into the Quaternary. Corresponding observations along the eastern border of the Pocitos Basin show that <3.5-m.y.-old strata are involved in contractile deformation and basin compartmentalization. Shortening in the central Puna is compatible with Plio-Pleistocene shortening in the low-elevation Salar de Atacama farther west, and may indicate that low-elevation sectors of the plateau have not yet reached a critical elevation that is conducive to normal faulting as observed elsewhere. The onset of extensional deformation in the Puna is thus highly disparate in space and time. Coeval regional thrusting, strike-slip, and normal faulting do not support a structural and topographic setting that promotes wholesale extension and orogenic collapse of the plateau realm.

Moderate rates of late Quaternary slip along the northwestern margin of the Basin and Range Province, Surprise Valley fault, northeastern California

USGS Publications Warehouse

Personius, Stephen F.; Crone, Anthony J.; Machette, Michael N.; Mahan, Shannon; Lidke, David J.

2009-01-01

The 86-km-long Surprise Valley normal fault forms part of the active northwestern margin of the Basin and Range province in northeastern California. We use trench mapping and radiocarbon, luminescence, and tephra dating to estimate displacements and timing of the past five surface-rupturing earthquakes on the central part of the fault near Cedarville. A Bayesian OxCal analysis of timing constraints indicates earthquake times of 18.2 ± 2.6, 10.9 ± 3.2, 8.5 ± 0.5, 5.8 ± 1.5, and 1.2 ± 0.1 ka. These data yield recurrence intervals of 7.3 ± 4.1, 2.5 ± 3.2, 2.7 ± 1.6, and 4.5 ± 1.5 ka and an elapsed time of 1.2 ± 0.1 ka since the latest surface-rupturing earthquake. Our best estimate of latest Quaternary vertical slip rate is 0.6 ?? 0.1 mm/a. This late Quaternary rate is remarkably similar to long-term (8-14 Ma) minimum vertical slip rates (>0.4-0.5 ± 0.3 mm/a) calculated from recently acquired seismic reflection and chronologic and structural data in Surprise Valley and the adjacent Warner Mountains. However, our slip rate yields estimates of extension that are lower than recent campaign GPS determinations by factors of 1.5-4 unless the fault has an unusually shallow (30°-35°) dip as suggested by recently acquired seismic reflection data. Coseismic displacements of 2-4.5 ± 1 m documented in the trench and probable rupture lengths of 53-65 km indicate a history of latest Quaternary earthquakes of M 6.8-7.3 on the central part of the. Surprise Valley fault.

Test plan. GCPS task 7, subtask 7.1: IHM development

NASA Technical Reports Server (NTRS)

Greenberg, H. S.

1994-01-01

The overall objective of Task 7 is to identify cost-effective life cycle integrated health management (IHM) approaches for a reusable launch vehicle's primary structure. Acceptable IHM approaches must: eliminate and accommodate faults through robust designs, identify optimum inspection/maintenance periods, automate ground and on-board test and check-out, and accommodate and detect structural faults by providing wide and localized area sensor and test coverage as required. These requirements are elements of our targeted primary structure low cost operations approach using airline-like maintenance by exception philosophies. This development plan will follow an evolutionary path paving the way to the ultimate development of flight-quality production, operations, and vehicle systems. This effort will be focused on maturing the recommended sensor technologies required for localized and wide area health monitoring to a technology readiness level (TRL) of 6 and to establish flight ready system design requirements. The following is a brief list of IHM program objectives: design out faults by analyzing material properties, structural geometry, and load and environment variables and identify failure modes and damage tolerance requirements; design in system robustness while meeting performance objectives (weight limitations) of the reusable launch vehicle primary structure; establish structural integrity margins to preclude the need for test and checkout and predict optimum inspection/maintenance periods through life prediction analysis; identify optimum fault protection system concept definitions combining system robustness and integrity margins established above with cost effective health monitoring technologies; and use coupons, panels, and integrated full scale primary structure test articles to identify, evaluate, and characterize the preferred NDE/NDI/IHM sensor technologies that will be a part of the fault protection system.

Kinematics of syn- and post-exhumational shear zones at Lago di Cignana (Western Alps, Italy): constraints on the exhumation of Zermatt-Saas (ultra)high-pressure rocks and deformation along the Combin Fault and Dent Blanche Basal Thrust

NASA Astrophysics Data System (ADS)

Kirst, Frederik; Leiss, Bernd

2017-01-01

Kinematic analyses of shear zones at Lago di Cignana in the Italian Western Alps were used to constrain the structural evolution of units from the Piemont-Ligurian oceanic realm (Zermatt-Saas and Combin zones) and the Adriatic continental margin (Dent Blanche nappe) during Palaeogene syn- and post-exhumational deformation. Exhumation of Zermatt-Saas (U)HP rocks to approximately lower crustal levels at ca. 39 Ma occurred during normal-sense top-(S)E shearing under epidote-amphibolite-facies conditions. Juxtaposition with the overlying Combin zone along the Combin Fault at mid-crustal levels occurred during greenschist-facies normal-sense top-SE shearing at ca. 38 Ma. The scarcity of top-SE kinematic indicators in the hanging wall of the Combin Fault probably resulted from strain localization along the uppermost Zermatt-Saas zone and obliteration by subsequent deformation. A phase of dominant pure shear deformation around 35 Ma affected units in the direct footwall and hanging wall of the Combin Fault. It is interpreted to reflect NW-SE crustal elongation during updoming of the nappe stack as a result of underthrusting of European continental margin units and the onset of continental collision. This phase was partly accompanied and followed by ductile bulk top-NW shearing, especially at higher structural levels, which transitioned into semi-ductile to brittle normal-sense top-NW deformation due to Vanzone phase folding from ca. 32 Ma onwards. Our structural observations suggest that syn-exhumational deformation is partly preserved within units and shear zones exposed at Lago di Cignana but also that the Combin Fault and Dent Blanche Basal Thrust experienced significant post-exhumational deformation reworking and overprinting earlier structures.

Geophysical constraints on the Virgin River Depression, Nevada, Utah, and Arizona

USGS Publications Warehouse

Langenheim, V.E.; Glen, J.M.; Jachens, R.C.; Dixon, G.L.; Katzer, T.C.; Morin, R.L.

2000-01-01

Gravity and aeromagnetic data provide insights into the subsurface lithology and structure of the Virgin River Depression (VRD) of Nevada, Utah, and Arizona. The gravity data indicate that the Quaternary and Tertiary sedimentary deposits hide a complex pre-Cenozoic surface. A north-northwest-trending basement ridge separates the Mesquite and Mormon basins, as evidenced by seismic-reflection, gravity, and aeromagnetic data. The Mesquite basin is very deep, reaching depths of 8?10 km. The Mormon basin reaches thicknesses of 5 km. Its northern margin is very steep and may be characterized by right steps, although this interpretation could change with additional gravity stations. Most of the young (Quaternary), small-displacement faults trend within 10? of due north and occur within the deeper parts of the Mesquite basin north of the Virgin River. South of the Virgin River, only a few, young, small-displacement faults are mapped; the trend of these faults is more northeasterly and parallels the basement topography and is distinct from that of the faults to the north. The Virgin River appears to follow the margin of the basin as it emerges from the plateau. The high-resolution aeromagnetic data outline the extent of shallow volcanic rocks in the Mesquite basin. The north-northwest alignment of volcanic rocks east of Toquop Wash appear to be structurally controlled because of faults imaged on seismic-reflection profiles and because the alignment is nearly perpendicular to the direction of Cenozoic extension. More buried volcanics likely exist to the north and east of the high-resolution aeromagnetic survey. Broader aeromagnetic anomalies beneath pre-Cenozoic basement in the Mormon Mountains and Tule Springs Hills reflect either Precambrian basement or Tertiary intrusions. These rocks are probably barriers to groundwater flow, except where fractured.

Latest Quaternary paleoseismology and evidence of distributed dextral shear along the Mohawk Valley fault zone, northern Walker Lane, California

USGS Publications Warehouse

Gold, Ryan D.; Briggs, Richard; Personius, Stephen; Crone, Anthony J.; Mahan, Shannon; Angster, Stephen

2014-01-01

The dextral-slip Mohawk Valley fault zone (MVFZ) strikes northwestward along the eastern margin of the Sierra Nevada in the northern Walker Lane. Geodetic block modeling indicates that the MVFZ may accommodate ~3 mm/yr of regional dextral strain, implying that it is the highest slip-rate strike-slip fault in the region; however, only limited geologic data are available to constrain the system’s slip rate and earthquake history. We mapped the MVFZ using airborne lidar data and field observations and identified a site near Sulphur Creek for paleoseismic investigation. At this site, oblique dextral-normal faulting on the steep valley margin has created a closed depression that floods annually during spring snowmelt to form an ephemeral pond. We excavated three fault-perpendicular trenches at the site and exposed pond sediment that interfingers with multiple colluvial packages eroded from the scarp that bounds the eastern side of the pond. We documented evidence for four surface-rupturing earthquakes on this strand of the MVFZ. OxCal modeling of radiocarbon and luminescence ages indicates that these earthquakes occurred at 14.0 ka, 12.8 ka, 5.7 ka, and 1.9 ka. The mean ~4 kyr recurrence interval is inconsistent with slip rates of ~3 mm/yr; these rates imply surface ruptures of more than 10 m per event, which is geologically implausible for the subdued geomorphic expression and 60 km length of the MVFZ. We propose that unidentified structures not yet incorporated into geodetic models may accommodate significant dextral shear across the northern Walker Lane, highlighting the role of distributed deformation in this region.

Present-day crustal deformation and strain transfer in northeastern Tibetan Plateau

NASA Astrophysics Data System (ADS)

Li, Yuhang; Liu, Mian; Wang, Qingliang; Cui, Duxin

2018-04-01

The three-dimensional present-day crustal deformation and strain partitioning in northeastern Tibetan Plateau are analyzed using available GPS and precise leveling data. We used the multi-scale wavelet method to analyze strain rates, and the elastic block model to estimate slip rates on the major faults and internal strain within each block. Our results show that shear strain is strongly localized along major strike-slip faults, as expected in the tectonic extrusion model. However, extrusion ends and transfers to crustal contraction near the eastern margin of the Tibetan Plateau. The strain transfer is abrupt along the Haiyuan Fault and diffusive along the East Kunlun Fault. Crustal contraction is spatially correlated with active uplifting. The present-day strain is concentrated along major fault zones; however, within many terranes bounded by these faults, intra-block strain is detectable. Terranes having high intra-block strain rates also show strong seismicity. On average the Ordos and Sichuan blocks show no intra-block strain, but localized strain on the southwestern corner of the Ordos block indicates tectonic encroachment.

Fault diagnosis of power transformer based on fault-tree analysis (FTA)

NASA Astrophysics Data System (ADS)

Wang, Yongliang; Li, Xiaoqiang; Ma, Jianwei; Li, SuoYu

2017-05-01

Power transformers is an important equipment in power plants and substations, power distribution transmission link is made an important hub of power systems. Its performance directly affects the quality and health of the power system reliability and stability. This paper summarizes the five parts according to the fault type power transformers, then from the time dimension divided into three stages of power transformer fault, use DGA routine analysis and infrared diagnostics criterion set power transformer running state, finally, according to the needs of power transformer fault diagnosis, by the general to the section by stepwise refinement of dendritic tree constructed power transformer fault

Flexible $$I_{Q}\\!\\!-\\!\\!V$$ Scheme of a DFIG for Rapid Voltage Regulation of a Wind Power Plant

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kim, Jinho; Muljadi, Eduard; Park, Jung -Wook

This paper proposes a flexible reactive current-to-voltage (I Q-V) scheme of a doubly-fed induction generator (DFIG) for the rapid voltage regulation of a wind power plant (WPP). In the proposed scheme, the WPP controller dispatches different voltage set points to the DFIGs depending on their rotor voltage margins. The DFIGs inject different reactive power with the flexible I Q-V schemes implemented in the rotor-side and grid-side converters. The I Q-V characteristic, which consists of the gain and width of a linear band and I Q capability, varies with time depending on the I Q capability of the converters and amore » voltage dip at the point of interconnection (POI). To increase the I Q capability during a fault, the active current is reduced in proportion to a voltage dip. If the I Q capability and/or the POI voltage dip are large, the I Q-V gain is set to be high, thereby providing rapid voltage regulation. To avoid an overvoltage after the fault clearance, a rapid I Q reduction scheme is implemented in the WPP and DFIG controllers. The performance of the proposed flexible scheme was verified under scenarios with various disturbances. In conclusion, the proposed scheme can help increase wind power penetration without jeopardizing voltage stability.« less

Flexible $$I_{Q}\\!\\!-\\!\\!V$$ Scheme of a DFIG for Rapid Voltage Regulation of a Wind Power Plant

DOE PAGES

Kim, Jinho; Muljadi, Eduard; Park, Jung -Wook; ...

2017-04-28

This paper proposes a flexible reactive current-to-voltage (I Q-V) scheme of a doubly-fed induction generator (DFIG) for the rapid voltage regulation of a wind power plant (WPP). In the proposed scheme, the WPP controller dispatches different voltage set points to the DFIGs depending on their rotor voltage margins. The DFIGs inject different reactive power with the flexible I Q-V schemes implemented in the rotor-side and grid-side converters. The I Q-V characteristic, which consists of the gain and width of a linear band and I Q capability, varies with time depending on the I Q capability of the converters and amore » voltage dip at the point of interconnection (POI). To increase the I Q capability during a fault, the active current is reduced in proportion to a voltage dip. If the I Q capability and/or the POI voltage dip are large, the I Q-V gain is set to be high, thereby providing rapid voltage regulation. To avoid an overvoltage after the fault clearance, a rapid I Q reduction scheme is implemented in the WPP and DFIG controllers. The performance of the proposed flexible scheme was verified under scenarios with various disturbances. In conclusion, the proposed scheme can help increase wind power penetration without jeopardizing voltage stability.« less

Strain buildup and release, earthquake prediction and selection of VLB sites for the margins of the North Pacific

NASA Technical Reports Server (NTRS)

Scholz, C. H.; Johnson, T.

1976-01-01

Microearthquake studies of the southern section of the San Andreas fault system were conducted in order to elucidate the role of known but little studied complications in the fault system which could affect the SAFE measurement. Data reduction from microearthquake studies in Baja California, Mexico, was completed. In addition, styles of deformation on the Alpine fault in New Zealand and on the San Andreas fault were compared. Sections of these faults with comparable physical characteristics seem to deform in a similar manner, indicating that deformation style is controlled by certain fundamental relations and will continue in the future. The geology of eastern New Guinea is also discussed. Deformation in the area is proposed to be related to collision of a series of island arcs with central New Guinea, which is part of the Australian continent. Among other unusual properties, eastern New Guinea contains the highest anomaly of the gravimetrically determined geoid based on GEM 6 and surface gravity data.

Tectonic deformation of the Andes and the configuration of the subducted slab in central Peru: Results from a micro-seismic experiment

NASA Technical Reports Server (NTRS)

Suarez, G.; Gagnepain, J. J.; Cisternas, A.; Hatzfeld, D.; Molnar, P.; Ocola, L.; Roecker, S. W.; Viode, J. P.

1983-01-01

The vast majority of the microearthquakes recorded occurred to the east: on the Huaytapallana fault in the Eastern Cordillera or in the western margin of the sub-Andes. The sub-Andes appear to be the physiographic province subjected to the most intense seismic deformation. Focal depths for the crustal events here are as deep as 50 km, and the fault plane solutions, show thrust faulting on steep planes oriented roughly north-south. The Huaytapallana fault in the Cordillera Oriental also shows relatively high seismicity along a northeast-southwest trend that agrees with the fault scarp and the east dipping nodal plane of two large earthquakes that occurred on this fault in 1969. The recorded microearthquakes of intermediate depth show a flat seismic zone about 25 km thick at a depth of about 100 km. This agrees with the suggestion that beneath Peru the slab first dips at an angle of 30 deg to a depth of 100 km and then flattens following a quasi-horizontal trajectory. Fault plane solutions of intermediate depth microearthquakes have horizontal T axes oriented east-west.

A New Perspective on Fault Geometry and Slip Distribution of the 2009 Dachaidan Mw 6.3 Earthquake from InSAR Observations

PubMed Central

Liu, Yang; Xu, Caijun; Wen, Yangmao; Fok, Hok Sum

2015-01-01

On 28 August 2009, the northern margin of the Qaidam basin in the Tibet Plateau was ruptured by an Mw 6.3 earthquake. This study utilizes the Envisat ASAR images from descending Track 319 and ascending Track 455 for capturing the coseismic deformation resulting from this event, indicating that the earthquake fault rupture does not reach to the earth’s surface. We then propose a four-segmented fault model to investigate the coseismic deformation by determining the fault parameters, followed by inverting slip distribution. The preferred fault model shows that the rupture depths for all four fault planes mainly range from 2.0 km to 7.5 km, comparatively shallower than previous results up to ~13 km, and that the slip distribution on the fault plane is complex, exhibiting three slip peaks with a maximum of 2.44 m at a depth between 4.1 km and 4.9 km. The inverted geodetic moment is 3.85 × 1018 Nm (Mw 6.36). The 2009 event may rupture from the northwest to the southeast unilaterally, reaching the maximum at the central segment. PMID:26184210

A New Perspective on Fault Geometry and Slip Distribution of the 2009 Dachaidan Mw 6.3 Earthquake from InSAR Observations.

PubMed

Liu, Yang; Xu, Caijun; Wen, Yangmao; Fok, Hok Sum

2015-07-10

On 28 August 2009, the northern margin of the Qaidam basin in the Tibet Plateau was ruptured by an Mw 6.3 earthquake. This study utilizes the Envisat ASAR images from descending Track 319 and ascending Track 455 for capturing the coseismic deformation resulting from this event, indicating that the earthquake fault rupture does not reach to the earth's surface. We then propose a four-segmented fault model to investigate the coseismic deformation by determining the fault parameters, followed by inverting slip distribution. The preferred fault model shows that the rupture depths for all four fault planes mainly range from 2.0 km to 7.5 km, comparatively shallower than previous results up to ~13 km, and that the slip distribution on the fault plane is complex, exhibiting three slip peaks with a maximum of 2.44 m at a depth between 4.1 km and 4.9 km. The inverted geodetic moment is 3.85 × 10(18) Nm (Mw 6.36). The 2009 event may rupture from the northwest to the southeast unilaterally, reaching the maximum at the central segment.

Petrogenesis of the Zheduoshan Cenozoic granites in the eastern margin of Tibet: Constraints on the initial activity of the Xianshuihe Fault

NASA Astrophysics Data System (ADS)

Lai, Shao-cong; Zhao, Shao-wei

2018-06-01

The Zheduoshan Miocene granitic pluton is exposed at the eastern margin of Tibet and along the strike-slip Xianshuihe Fault, and is the product of syn-tectonic magmatism closely related to this fault. This paper is focused on the petrogenesis of different granitic lithological units in the Zheduoshan composite intrusion, and the results of geochronology and lithology show that the Zheduoshan Miocene granitic pluton is incremental assembly by three stages of granitic magma influx and growth, represented by fine-grain biotite granite at 18.0 Ma, corase-grain and porphyraceous biotite monzogranite at 16.0 Ma and medium-grain two-mica monzogranite at 14.0 Ma. Combining with the geochemical signatures, these granitic rocks have high intial 87Sr/86Sr ratios, enriched Nd and Hf isotopic compositions, revealing that the sources of these granitic rocks are metabasatic rocks for fine-grain biotite granite, greywackes for coarse-grain biotite monzogranite and medium-grain monzogranite. These granites have high Sr/Y ratios, revealing that these granitic magma form at high pressure condition. The Sr/Y ratios and calculated crystallization pressure gradually decreased, implying the pressure gradually decreasing with the formation of these three stages of granites, which is probably caused by the tectonic mechanism transition from compression to strike-slip extension during the generation of these granites at 18.0-14.4 Ma. This tectonic mechanism change implied the initial activity of Xianshuihe Fault at least before 14.4 Ma.

Postglacial rebound and fault instability in Fennoscandia

NASA Astrophysics Data System (ADS)

Wu, Patrick; Johnston, Paul; Lambeck, Kurt

1999-12-01

The best available rebound model is used to investigate the role that postglacial rebound plays in triggering seismicity in Fennoscandia. The salient features of the model include tectonic stress due to spreading at the North Atlantic Ridge, overburden pressure, gravitationally self-consistent ocean loading, and the realistic deglaciation history and compressible earth model which best fits the sea-level and ice data in Fennoscandia. The model predicts the spatio-temporal evolution of the state of stress, the magnitude of fault instability, the timing of the onset of this instability, and the mode of failure of lateglacial and postglacial seismicity. The consistency of the predictions with the observations suggests that postglacial rebound is probably the cause of the large postglacial thrust faults observed in Fennoscandia. The model also predicts a uniform stress field and instability in central Fennoscandia for the present, with thrust faulting as the predicted mode of failure. However, the lack of spatial correlation of the present seismicity with the region of uplift, and the existence of strike-slip and normal modes of current seismicity are inconsistent with this model. Further unmodelled factors such as the presence of high-angle faults in the central region of uplift along the Baltic coast would be required in order to explain the pattern of seismicity today in terms of postglacial rebound stress. The sensitivity of the model predictions to the effects of compressibility, tectonic stress, viscosity and ice model is also investigated. For sites outside the ice margin, it is found that the mode of failure is sensitive to the presence of tectonic stress and that the onset timing is also dependent on compressibility. For sites within the ice margin, the effect of Earth rheology is shown to be small. However, ice load history is shown to have larger effects on the onset time of earthquakes and the magnitude of fault instability.

A tectonic model for the Tertiary evolution of strike slip faults and rift basins in SE Asia

NASA Astrophysics Data System (ADS)

Morley, C. K.

2002-04-01

Models for the Tertiary evolution of SE Asia fall into two main types: a pure escape tectonics model with no proto-South China Sea, and subduction of proto-South China Sea oceanic crust beneath Borneo. A related problem is which, if any, of the main strike-slip faults (Mae Ping, Three Pagodas and Aliao Shan-Red River (ASRR)) cross Sundaland to the NW Borneo margin to facilitate continental extrusion? Recent results investigating strike-slip faults, rift basins, and metamorphic core complexes are reviewed and a revised tectonic model for SE Asia proposed. Key points of the new model include: (1) The ASRR shear zone was mainly active in the Eocene-Oligocene in order to link with extension in the South China Sea. The ASRR was less active during the Miocene (tens of kilometres of sinistral displacement), with minor amounts of South China Sea spreading centre extension transferred to the ASRR shear zone. (2) At least three important regions of metamorphic core complex development affected Indochina from the Oligocene-Miocene (Mogok gneiss belt; Doi Inthanon and Doi Suthep; around the ASRR shear zone). Hence, Paleogene crustal thickening, buoyancy-driven crustal collapse, and lower crustal flow are important elements of the Tertiary evolution of Indochina. (3) Subduction of a proto-South China Sea oceanic crust during the Eocene-Early Miocene is necessary to explain the geological evolution of NW Borneo and must be built into any model for the region. (4) The Eocene-Oligocene collision of NE India with Burma activated extrusion tectonics along the Three Pagodas, Mae Ping, Ranong and Klong Marui faults and right lateral motion along the Sumatran subduction zone. (5) The only strike-slip fault link to the NW Borneo margin occurred along the trend of the ASRR fault system, which passes along strike into a right lateral transform system including the Baram line.

Seismogenic structures of the 2006 ML4.0 Dangan Island earthquake offshore Hong Kong

NASA Astrophysics Data System (ADS)

Xia, Shaohong; Cao, Jinghe; Sun, Jinlong; Lv, Jinshui; Xu, Huilong; Zhang, Xiang; Wan, Kuiyuan; Fan, Chaoyan; Zhou, Pengxiang

2018-02-01

The northern margin of the South China Sea, as a typical extensional continental margin, has relatively strong intraplate seismicity. Compared with the active zones of Nanao Island, Yangjiang, and Heyuan, seismicity in the Pearl River Estuary is relatively low. However, a ML4.0 earthquake in 2006 occurred near Dangan Island (DI) offshore Hong Kong, and this site was adjacent to the source of the historical M5.8 earthquake in 1874. To reveal the seismogenic mechanism of intraplate earthquakes in DI, we systematically analyzed the structural characteristics in the source area of the 2006 DI earthquake using integrated 24-channel seismic profiles, onshore-offshore wide-angle seismic tomography, and natural earthquake parameters. We ascertained the locations of NW- and NE-trending faults in the DI sea and found that the NE-trending DI fault mainly dipped southeast at a high angle and cut through the crust with an obvious low-velocity anomaly. The NW-trending fault dipped southwest with a similar high angle. The 2006 DI earthquake was adjacent to the intersection of the NE- and NW-trending faults, which suggested that the intersection of the two faults with different strikes could provide a favorable condition for the generation and triggering of intraplate earthquakes. Crustal velocity model showed that the high-velocity anomaly was imaged in the west of DI, but a distinct entity with low-velocity anomaly in the upper crust and high-velocity anomaly in the lower crust was found in the south of DI. Both the 1874 and 2006 DI earthquakes occurred along the edge of the distinct entity. Two vertical cross-sections nearly perpendicular to the strikes of the intersecting faults revealed good spatial correlations between the 2006 DI earthquake and the low to high speed transition in the distinct entity. This result indicated that the transitional zone might be a weakly structural body that can store strain energy and release it as a brittle failure, resulting in an earthquake-prone area.

Dual-quaternion based fault-tolerant control for spacecraft formation flying with finite-time convergence.

PubMed

Dong, Hongyang; Hu, Qinglei; Ma, Guangfu

2016-03-01

Study results of developing control system for spacecraft formation proximity operations between a target and a chaser are presented. In particular, a coupled model using dual quaternion is employed to describe the proximity problem of spacecraft formation, and a nonlinear adaptive fault-tolerant feedback control law is developed to enable the chaser spacecraft to track the position and attitude of the target even though its actuator occurs fault. Multiple-task capability of the proposed control system is further demonstrated in the presence of disturbances and parametric uncertainties as well. In addition, the practical finite-time stability feature of the closed-loop system is guaranteed theoretically under the designed control law. Numerical simulation of the proposed method is presented to demonstrate the advantages with respect to interference suppression, fast tracking, fault tolerant and practical finite-time stability. Copyright © 2015 ISA. Published by Elsevier Ltd. All rights reserved.

A new Triassic shortening-extrusion tectonic model for Central-Eastern Asia: Structural, geochronological and paleomagnetic investigations in the Xilamulun Fault (North China)

NASA Astrophysics Data System (ADS)

Zhao, Pan; Faure, Michel; Chen, Yan; Shi, Guanzhong; Xu, Bei

2015-09-01

At the northern margin of the North China Block (NCB), the Xilamulun Fault (XMF) is a key belt to decipher the tectonic evolution of Central-Eastern Asia, as it records the Paleozoic final closure of the Paleo-Asian Ocean, and localizes a Late Triassic intracontinental deformation. In this study, structural analysis, 40Ar-39Ar dating, and paleomagnetic studies were performed to investigate the kinematics of the XMF and to further discuss its Triassic geodynamic significance in the Central-Eastern Asia framework after the Paleozoic Central Asian Orogenic evolution. The structural analyses reveal two phases of ductile deformation. The first one (D1), which displays N-verging and E-W trending folds, is related to the Early Paleozoic collisional event between the NCB and the Songliao-Hunshandake Block (SHB). The second phase (D2) displays a high-angle foliation and a pervasive sub-horizontal E-W stretching lineation with kinematic criteria indicative of dextral strike-slip shearing. The 40Ar-39Ar dating on mylonitic granite places the main shearing event around 227-209 Ma. This D2 shearing is coeval with that of the dextral strike-slip Bayan Obo-Chifeng Fault (BCF) and the Chicheng-Fengning-Longhua Fault to the south, which together constitute a dextral shearing fault system on the northern margin of the NCB during the Late Triassic. The paleomagnetic study performed on the Middle Permian Guangxingyuan pluton, located between the XMF and BCF, documents a local clockwise rotation of this pluton with respect to the NCB and SHB. Our multidisciplinary study suggests an NNW-SSE shortening and strike-slip shearing dominated tectonic setting on the northern margin of the NCB during the Late Triassic. Combining the contemporaneous dextral strike-slip movements of the XMF and BCF in northern China and the sinistral strike-slip movement of East Gobi Fault (EGF) in southeastern Mongolia with the large-scale tectonic framework, a Late Triassic NNW-SSE shortening-eastward extrusion tectonic model for Central-Eastern Asia is firstly proposed. The NNW-SSE shortening results in the eastward extrusion of the continental wedge bounded by the BCF and EGF, which is accommodated by the different kinematic patterns of the southern (XMF and BCF) and northwestern (EGF) bounding faults. This shortening-extrusion tectonic framework is tentatively interpreted as the result of the far field forces associated with three Late Triassic lithosphere-scale convergences in East Asia: i) northward intracontinental subduction between the NCB and South China Block, ii) collision of the Qiangtang Block with the Qaidam Block, and iii) southward subduction of the Mongol-Okhotsk Ocean beneath the Mongolia Block.

A new Triassic shortening-extrusion tectonic model for Central-EasternAsia: Structural, geochronological and paleomagnetic investigations in the Xilamulun Fault (North China)

NASA Astrophysics Data System (ADS)

Zhao, Pan; Faure, Michel; Chen, Yan; Xu, Bei

2017-04-01

At the northern margin of the North China Block (NCB), the Xilamulun Fault (XMF) is a key belt to decipher the tectonic evolution of Central-Eastern Asia, as it records the Paleozoic final closure of the Paleo-Asian Ocean, and localizes a Late Triassic intracontinental deformation. In this study, structural analysis, 40Ar-39Ar dating, and paleomagnetic studies were performed to investigate the kinematics of the XMF and to further discuss its Triassic geodynamic significance in the Central-Eastern Asia framework after the Paleozoic Central Asian Orogenic evolution. The structural analyses reveal two phases of ductile deformation. The first one (D1), which displays N-verging and E-W trending folds, is related to the Early Paleozoic collisional event between the NCB and the Songliao-Hunshandake Block (SHB). The second phase (D2) displays a high-angle foliation and a pervasive sub-horizontalE-W stretching lineation with kinematic criteria indicative of dextral strike-slip shearing. The 40Ar-39Ar dating on mylonitic granite places the main shearing event around 227-209 Ma. This D2 shearing is coeval with that of the dextral strike-slip Bayan Obo-Chifeng Fault (BCF) and the Chicheng-Fengning-Longhua Fault to the south, which together constitute a dextral shearing fault system on the northern margin of the NCB during the Late Triassic. The paleomagnetic study performed on the Middle Permian Guangxingyuan pluton, located between the XMF and BCF, documents a local clockwise rotation of this pluton with respect to the NCB and SHB. Our multidisciplinary study suggests anNNW-SSE shortening and strike-slip shearing dominated tectonic setting on the northern margin of the NCB during the Late Triassic. Combining the contemporaneous dextral strike-slip movements of the XMF and BCF in northern China and the sinistral strike-slip movement of East Gobi Fault (EGF) in southeastern Mongolia with the large-scale tectonic framework, a Late Triassic NNW-SSE shortening-eastward extrusion tectonic model for Central-Eastern Asia is firstly proposed. The NNW-SSE shortening results in the eastward extrusion of the continental wedge bounded by the BCF and EGF, which is accommodated by the different kinematic patterns of the southern (XMF and BCF) and northwestern (EGF) bounding faults. This shortening-extrusion tectonic framework is tentatively interpreted as the result of the far field forces associated with three Late Triassic lithosphere-scale convergences in East Asia: i)northward intracontinental subduction between the NCB and South China Block, ii)collision of the Qiangtang Block with the Qaidam Block, and iii)southward subduction of the Mongol-Okhotsk Ocean beneath the Mongolia Block.

Development of a 30-kA cable-in-conduit conductor for pulsed poloidal coils

DOE Office of Scientific and Technical Information (OSTI.GOV)

Takashi, Y.; Dresner, L.; Kato, T.

1983-05-01

This paper describes design parameters of a 30-kA cable-in-conduit conductor (JF-30), and the test results of stability margin measured by using a triplex in a conduit. Cross sectional size of JF-30 is 35mm X 35 mm and 567 NbTi-Cu-CuNi strands are in a stainless steel conduit whose thickness is 2 mm. Void fraction is 33 % and the designed stability margin is 270 mJ/cc at 5 atm and 7 T. Stability test by a triplex showed a favorable margin, a few hundreds of mJ at 7 T even without helium flow. In addition, the stability was strongly increased when heliummore » flow up to 0.2 g/s was applied. At around 3 atm, the authors found that the stability margin was more than 2 J/cc which exceeded the present heater capacity. This resulted in an extension of current range, in which the sample is stable, up to 150 to 200 % when compared to the case without helium flow.« less

Slip behaviour of experimental faults subjected to fluid pressure stimulation: carbonates vs. shales

NASA Astrophysics Data System (ADS)

Collettini, C.; Scuderi, M. M.; Marone, C.

2017-12-01

Fluid overpressure is one of the primary mechanisms for triggering tectonic fault slip and human-induced seismicity. This mechanism has been invoked to explain the dramatic increase in seismicity associated with waste water disposal in intra-plate setting, and it is appealing because fluids lubricate the fault and reduce the effective normal stress that holds the fault in place. Although, this basic physical mechanism is well understood, several fundamental questions remain including the apparent delay between fluid injection and seismicity, the role of fault zone rheology, and the relationship between injection volume and earthquake size. Moreover, models of earthquake nucleation predict that a reduction in normal stress, as expected for fluid overpressure, should stabilize fault slip. Here, we address these questions using laboratory experiments, conducted in the double direct shear configuration in a true-triaxial machine on carbonates and shale fault gouges. In particular, we: 1) evaluate frictional strength and permeability, 2) characterize the rate- and state- friction parameters and 3) study fault slip evolution during fluid pressure stimulations. With increasing fluid pressure, when shear and effective normal stresses reach the failure condition, in calcite gouges, characterized by slightly velocity strengthening behaviour, we observe an acceleration of slip that spontaneously evolves into dynamic failure. For shale gouges, with a strong rate-strengthening behaviour, we document complex fault slip behavior characterized by periodic accelerations and decelerations with slip velocity that remains slow (i.e. v 200 µm/s), never approaching dynamic slip rates. Our data indicate that fault rheology and fault stability is controlled by the coupling between fluid pressure and rate- and state- friction parameters suggesting that their comprehensive characterization is fundamental for assessing the role of fluid pressure in natural and human induced earthquakes.

An empirically based steady state friction law and implications for fault stability

PubMed Central

Nielsen, S.; Violay, M.; Di Toro, G.

2016-01-01

Abstract Empirically based rate‐and‐state friction laws (RSFLs) have been proposed to model the dependence of friction forces with slip and time. The relevance of the RSFL for earthquake mechanics is that few constitutive parameters define critical conditions for fault stability (i.e., critical stiffness and frictional fault behavior). However, the RSFLs were determined from experiments conducted at subseismic slip rates (V < 1 cm/s), and their extrapolation to earthquake deformation conditions (V > 0.1 m/s) remains questionable on the basis of the experimental evidence of (1) large dynamic weakening and (2) activation of particular fault lubrication processes at seismic slip rates. Here we propose a modified RSFL (MFL) based on the review of a large published and unpublished data set of rock friction experiments performed with different testing machines. The MFL, valid at steady state conditions from subseismic to seismic slip rates (0.1 µm/s < V < 3 m/s), describes the initiation of a substantial velocity weakening in the 1–20 cm/s range resulting in a critical stiffness increase that creates a peak of potential instability in that velocity regime. The MFL leads to a new definition of fault frictional stability with implications for slip event styles and relevance for models of seismic rupture nucleation, propagation, and arrest. PMID:27667875

Effect of Pore Pressure on Slip Failure of an Impermeable Fault: A Coupled Micro Hydro-Geomechanical Model

NASA Astrophysics Data System (ADS)

Yang, Z.; Juanes, R.

2015-12-01

The geomechanical processes associated with subsurface fluid injection/extraction is of central importance for many industrial operations related to energy and water resources. However, the mechanisms controlling the stability and slip motion of a preexisting geologic fault remain poorly understood and are critical for the assessment of seismic risk. In this work, we develop a coupled hydro-geomechanical model to investigate the effect of fluid injection induced pressure perturbation on the slip behavior of a sealing fault. The model couples single-phase flow in the pores and mechanics of the solid phase. Granular packs (see example in Fig. 1a) are numerically generated where the grains can be either bonded or not, depending on the degree of cementation. A pore network is extracted for each granular pack with pore body volumes and pore throat conductivities calculated rigorously based on geometry of the local pore space. The pore fluid pressure is solved via an explicit scheme, taking into account the effect of deformation of the solid matrix. The mechanics part of the model is solved using the discrete element method (DEM). We first test the validity of the model with regard to the classical one-dimensional consolidation problem where an analytical solution exists. We then demonstrate the ability of the coupled model to reproduce rock deformation behavior measured in triaxial laboratory tests under the influence of pore pressure. We proceed to study the fault stability in presence of a pressure discontinuity across the impermeable fault which is implemented as a plane with its intersected pore throats being deactivated and thus obstructing fluid flow (Fig. 1b, c). We focus on the onset of shear failure along preexisting faults. We discuss the fault stability criterion in light of the numerical results obtained from the DEM simulations coupled with pore fluid flow. The implication on how should faults be treated in a large-scale continuum model is also presented.

Evidence of post-Pleistocene faults on New Jersey Atlantic outer continental shelf

USGS Publications Warehouse

Sheridan, R.E.; Knebel, H.J.

1976-01-01

Recently obtained high-resolution seismic profiles (400-4,000-Hz band) show evidence of faults in shallow sedimentary strata near the edge of the Atlantic continental shelf off New Jersey. Apparent normal faults having a throw of about 1.5 m displace sediments to within 7 m of the sea floor. The faults appear to be overlain by undeformed horizontal beds of relatively recent age. Several faults 1 to 2 km apart strike approximately N70°E and dip northwest. The data suggest that the faults are upthrown on the southeast.Projection of the faults on the high-resolution profiles to a nearby multichannel seismic-reflection profile indicates that these shallow faults might be the near-surface expression of a more fundamental deep-seated fault. Several prominent reflectors in the multichannel records are offset by a high-angle normal fault reaching depths of 4.0 to 5.0 sec (6.0 to 6.5 km). The deep fault on the multichannel line also is upthrown on the southeast. Throws of as much as 90 m are apparent at depth, but offsets of as much as 10 m could be present in the shallower parts of the section that may not be resolved in the multichannel data.The position and strike of these faults coincide with and parallel the East Coast magnetic anomaly interpreted as the fundamental seaward basement boundary of the Baltimore Canyon trough. Recurring movements along such boundary faults are expected theoretically if the marginal basins are subsiding in response to the plate rotation of North America and seafloor spreading in the Atlantic.

Real-Time Stability Margin Measurements for X-38 Robustness Analysis

NASA Technical Reports Server (NTRS)

Bosworth, John T.; Stachowiak, Susan J.

2005-01-01

A method has been developed for real-time stability margin measurement calculations. The method relies on a tailored-forced excitation targeted to a specific frequency range. Computation of the frequency response is matched to the specific frequencies contained in the excitation. A recursive Fourier transformation is used to make the method compatible with real-time calculation. The method was incorporated into the X-38 nonlinear simulation and applied to an X-38 robustness test. X-38 stability margins were calculated for different variations in aerodynamic and mass properties over the vehicle flight trajectory. The new method showed results comparable to more traditional stability analysis techniques, and at the same time, this new method provided coverage that is more complete and increased efficiency.

Verifiable Adaptive Control with Analytical Stability Margins by Optimal Control Modification

NASA Technical Reports Server (NTRS)

Nguyen, Nhan T.

2010-01-01

This paper presents a verifiable model-reference adaptive control method based on an optimal control formulation for linear uncertain systems. A predictor model is formulated to enable a parameter estimation of the system parametric uncertainty. The adaptation is based on both the tracking error and predictor error. Using a singular perturbation argument, it can be shown that the closed-loop system tends to a linear time invariant model asymptotically under an assumption of fast adaptation. A stability margin analysis is given to estimate a lower bound of the time delay margin using a matrix measure method. Using this analytical method, the free design parameter n of the optimal control modification adaptive law can be determined to meet a specification of stability margin for verification purposes.

The Porcupine Basin: from rifting to continental breakup

NASA Astrophysics Data System (ADS)

Reston, Timothy; Gaw, Viola; Klaeschen, Dirk; McDermott, Ken

2015-04-01

Southwest of Ireland, the Porcupine Basin is characterized by axial stretching factors that increase southward to values greater than six and typical of rifted margins. As such, the basin can be regarded as a natural laboratory to investigate the evolution and symmetry of rifting leading towards continental separation and breakup, and in particular the processes of mantle serpentinisation, and the onset of detachment faulting. We have processed through to prestack depth migration a series of E-W profiles crossing the basin at different axial stretching factors and linked by a N-S profile running close to the rift axis. Our results constrain the structure of the basin and have implications for the evolution of rifted margins. In the north at a latitude of 52.25N, no clear detachment is imaged, although faults do appear to cut down into the mantle, so that serpentinisation may have started. Further south (51.75N), a bright reflection (here named P) cuts down to the west from the base of the sedimentary section, is overlain by small fault blocks and appears to represent a detachment fault. P may in part follow the top of partially serpentinized mantle: this interpretation is consistent with gravity modelling, with numerical models of crustal embrittlement and mantle serpentinization during extension and with wide-angle data (see posters of Prada and of Watremez). Furthermore, P closely resembles the S reflection west of Iberia, where such serpentinites are well documented. P develops where the crust was thinned to less than 3 km during rifting, again similar to S. Although overall the basin remains symmetrical, the consistent westward structural dip of the detachment implies that, at high stretching factors, extension became asymmetric. Analysis of the depth sections suggests that the detachment may have been active as a rolling hinge rooting at low-angle beneath the Porcupine Bank, consistent with the presence of a footwall of serpentinites. This requires very weak fault rocks, such as serpentinites. Reconstructions suggest that the detachment developed after the onset of serpentinisation and thus represents late stage of faulting within a complex polyphase rift history. Farther south still, a N-S running profile shows that P cuts up to form the top of the basement, and locally forms the top of what we interpret as exhumed mantle, since buried by postrift sediments. Thus detachment here appear to have been both responsible for the late-stage extension of the crust and the unroofing of the mantle. The same processes are likely to have occurred at magma poor rifted margins.

New perspectives on the evolution of narrow, modest extension continental rifts: Embryonic core complexes and localized, rapid Quaternary extension in the Rio Grande rift, central New Mexico

NASA Astrophysics Data System (ADS)

Ricketts, J.; Karlstrom, K. E.; Kelley, S.

2013-12-01

Updated models for continental rift zones need to address the role and development of low-angle normal fault networks, episodicity of extension, and interaction of 'active and passive' driving mechanisms. In the Rio Grande rift, USA, low-angle normal faults are found throughout the entire length of the rift, but make up a small percentage of the total fault population. The low-angle Jeter and Knife Edge faults, for example, crop out along the SW and NE margins of the Albuquerque basin, respectively. Apatite fission track (AFT) age-elevation data and apatite (U-Th)/He (AHe) ages from these rift flank uplifts record cooling between ~21 - 16 Ma in the NE rift flank and ~20 - 10 Ma in the SW, which coincides with times of rapid extension and voluminous syntectonic sedimentation. The timing of exhumation is also similar to rift flanks farther north in active margins based on AFT data alone. In addition, synthetic faults in the hanging wall of each low-angle fault become progressively steeper and younger basinward, and footwall blocks are the highest elevation along the rift flanks. These observations are consistent with a model where initially high-angle faults are shallowed in regions of maximum extension. As they rotate, new intrabasinal faults emerge which also can be rotated if extension continues. These relationships are similarly described in mature core complexes, and if these processes continued in the Rio Grande rift, it could eventually result in mid-crustal ductily deformed rocks in the footwall placed against surficial deposits in the hanging wall across faults that have been isostatically rotated to shallow dips. Although existing data are consistent with highest strain rates during a pulse of extension along the entire length of the rift 20-10 Ma., GPS-constrained measurements suggest that the rift is still actively-extending at 1.23-1.39 nstr/yr (Berglund et al., 2012). Additional evidence for Quaternary extension comes from travertine deposits that are cut by multiple tensile vein sets along the western margin of the Albuquerque basin in the Lucero uplift. At this location, U-series ages on travertine deposits are used to calculate strain rates at this location. These strain rates (15-105 nstr/yr) are higher than both the modern strain rates as well as the average long-term strain rates (3-14 nstr/yr) obtained from restored cross-sections across different basins in the rift. To explain these observations, we propose a model involving high fluid pressures, which promote the formation of tensile veins that are oriented with respect to the modern day stress field in the rift. These regions of anomalously-high strain need not be widespread, and are only active on timescales of the hydraulic system, but they are nevertheless an underappreciated mechanism of progressive extension in the rift. Berglund, H.T., Sheehan, A.F., Murray, M.H., Roy, M., Lowry, A.R., Nerem, R.S., and Blume, F., 2012, Distributed deformation across the Rio Grande Rift, Great Plains, and Colorado Plateau: Geology, v. 40, p. 23-26.

Tectonic reversal of the western Doruneh Fault System: Implications for Central Asian tectonics

NASA Astrophysics Data System (ADS)

Javadi, Hamid Reza; Esterabi Ashtiani, Marzieh; Guest, Bernard; Yassaghi, Ali; Ghassemi, Mohammad Reza; Shahpasandzadeh, Majid; Naeimi, Amir

2015-10-01

The left-lateral Doruneh Fault System (DFS) bounds the north margin of the Central Iranian microplate and has played an important role in the structural evolution of the Turkish-Iranian plateau. The western termination of the DFS is a sinistral synthetic branch fault array that shows clear kinematic evidence of having undergone recent slip sense inversion from a dextral array to a sinistral array in the latest Neogene or earliest Quaternary. Similarly, kinematic evidence from the Anarak Metamorphic complex suggests that this complex initially developed at a transpressive left-stepping termination of the DFS and that it was inverted in the latest Neogene to a transtensional fault termination. The recognition that the DFS and other faults in NE Iran were inverted from dextral to sinistral strike slip in the latest Neogene and the likely connection between the DFS and the Herat Fault of Afghanistan suggests that prior to the latest Miocene, all of the north Iranian and northern Afghan ranges were part of a distributed dextral fault network that extended from the west Himalayan syntaxes to the western Alborz. Also, the recognition that regional slip sense inversion occurred across northern and northeastern Iran after the latest Miocene invalidates tectonic models that extrapolate Pleistocene to recent fault slip kinematics and rates back beyond this time.

Methodology for fault detection in induction motors via sound and vibration signals

NASA Astrophysics Data System (ADS)

Delgado-Arredondo, Paulo Antonio; Morinigo-Sotelo, Daniel; Osornio-Rios, Roque Alfredo; Avina-Cervantes, Juan Gabriel; Rostro-Gonzalez, Horacio; Romero-Troncoso, Rene de Jesus

2017-01-01

Nowadays, timely maintenance of electric motors is vital to keep up the complex processes of industrial production. There are currently a variety of methodologies for fault diagnosis. Usually, the diagnosis is performed by analyzing current signals at a steady-state motor operation or during a start-up transient. This method is known as motor current signature analysis, which identifies frequencies associated with faults in the frequency domain or by the time-frequency decomposition of the current signals. Fault identification may also be possible by analyzing acoustic sound and vibration signals, which is useful because sometimes this information is the only available. The contribution of this work is a methodology for detecting faults in induction motors in steady-state operation based on the analysis of acoustic sound and vibration signals. This proposed approach uses the Complete Ensemble Empirical Mode Decomposition for decomposing the signal into several intrinsic mode functions. Subsequently, the frequency marginal of the Gabor representation is calculated to obtain the spectral content of the IMF in the frequency domain. This proposal provides good fault detectability results compared to other published works in addition to the identification of more frequencies associated with the faults. The faults diagnosed in this work are two broken rotor bars, mechanical unbalance and bearing defects.

The kinematic history of the Khlong Marui and Ranong Faults, southern Thailand

NASA Astrophysics Data System (ADS)

Watkinson, Ian; Elders, Chris; Hall, Robert

2008-12-01

The Khlong Marui Fault (KMF) and Ranong Fault (RF) are major NNE-trending strike-slip faults which dissect peninsular Thailand. They have been assumed to be conjugate to the NW-trending Three Pagodas Fault (TPF) and Mae Ping Fault (MPF) in Northern Thailand, which experienced a diachronous reversal in shear sense during India-Eurasia collision. It follows that the KMF and RF are expected to show the opposite shear sense and a slip sense reversal at a similar time to the TPF and MPF. New field data from the KMF and RF reveal two phases of ductile dextral shear separated by Campanian magmatism. Paleocene to Eocene post-kinematic granites date the end of this phase, while a brittle sinistral phase deforms the granites, and has exhumed the ductile fault rocks. The timing of these movements precludes formation of the faults in response to Himalayan extrusion tectonics. Instead, they formed near the southern margin of a Late Cretaceous-Paleocene orogen, and may have been influenced by variations in the rate of subduction ahead of India and Australia. North-south compression prior to reactivation of the subduction zone around southern Sundaland in the Eocene caused widespread deformation in the over-riding plate, including sinistral transpression on the KMF and RF.

Geological modeling of a fault zone in clay rocks at the Mont-Terri laboratory (Switzerland)

NASA Astrophysics Data System (ADS)

Kakurina, M.; Guglielmi, Y.; Nussbaum, C.; Valley, B.

2016-12-01

Clay-rich formations are considered to be a natural barrier for radionuclides or fluids (water, hydrocarbons, CO2) migration. However, little is known about the architecture of faults affecting clay formations because of their quick alteration at the Earth's surface. The Mont Terri Underground Research Laboratory provides exceptional conditions to investigate an un-weathered, perfectly exposed clay fault zone architecture and to conduct fault activation experiments that allow explore the conditions for stability of such clay faults. Here we show first results from a detailed geological model of the Mont Terri Main Fault architecture, using GoCad software, a detailed structural analysis of 6 fully cored and logged 30-to-50m long and 3-to-15m spaced boreholes crossing the fault zone. These high-definition geological data were acquired within the Fault Slip (FS) experiment project that consisted in fluid injections in different intervals within the fault using the SIMFIP probe to explore the conditions for the fault mechanical and seismic stability. The Mont Terri Main Fault "core" consists of a thrust zone about 0.8 to 3m wide that is bounded by two major fault planes. Between these planes, there is an assembly of distinct slickensided surfaces and various facies including scaly clays, fault gouge and fractured zones. Scaly clay including S-C bands and microfolds occurs in larger zones at top and bottom of the Mail Fault. A cm-thin layer of gouge, that is known to accommodate high strain parts, runs along the upper fault zone boundary. The non-scaly part mainly consists of undeformed rock block, bounded by slickensides. Such a complexity as well as the continuity of the two major surfaces are hard to correlate between the different boreholes even with the high density of geological data within the relatively small volume of the experiment. This may show that a poor strain localization occurred during faulting giving some perspectives about the potential for reactivation and leakage of faults affecting clay materials.

Jurassic faults of southwest Alabama and offshore areas

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mink, R.M.; Tew, B.H.; Bearden, B.L.

1991-03-01

Four fault groups affecting Jurassic strata occur in the southwest and offshore Alabama areas. They include the regional basement rift trend, the regional peripheral fault trend, the Mobile graben fault system, and the Lower Mobile Bay fault system. The regional basement system rift and regional peripheral fault trends are distinct and rim the inner margin of the eastern Gulf Coastal Plain. The regional basement rift trend is genetically related to the breakup of Pangea and the opening of the Gulf of Mexico in the Late Triassic-Early Jurassic. This fault trend is thought to have formed contemporaneously with deposition of Latemore » Triassic-Early Jurassic Eagle Mills Formation and to displace pre-Mesozoic rocks. The regional peripheral fault trend consists of a group of en echelon extensional faults that are parallel or subparallel to regional strike of Gulf Coastal Plain strata and correspond to the approximate updip limit of thick Louann Salt. Nondiapiric salt features are associated with the trend and maximum structural development is exhibited in the Haynesville-Smackover section. No hydrocarbon accumulations have been documented in the pre-Jurassic strata of southwest and offshore Alabama. Productive hydrocarbon reservoirs occur in Jurassic strata along the trends of the fault groups, suggesting a significant relationship between structural development in the Jurassic and hydrocarbon accumulation. Hydrocarbon traps are generally structural or contain a major structural component and include salt anticlines, faulted salt anticlines, and extensional fault traps. All of the major hydrocarbon accumulations are associated with movement of the Louann Salt along the regional peripheral fault trend, the Mobile graben fault system, or the Lower Mobile Bay fault system.« less

Electric machine differential for vehicle traction control and stability control

NASA Astrophysics Data System (ADS)

Kuruppu, Sandun Shivantha

Evolving requirements in energy efficiency and tightening regulations for reliable electric drivetrains drive the advancement of the hybrid electric (HEV) and full electric vehicle (EV) technology. Different configurations of EV and HEV architectures are evaluated for their performance. The future technology is trending towards utilizing distinctive properties in electric machines to not only to improve efficiency but also to realize advanced road adhesion controls and vehicle stability controls. Electric machine differential (EMD) is such a concept under current investigation for applications in the near future. Reliability of a power train is critical. Therefore, sophisticated fault detection schemes are essential in guaranteeing reliable operation of a complex system such as an EMD. The research presented here emphasize on implementation of a 4kW electric machine differential, a novel single open phase fault diagnostic scheme, an implementation of a real time slip optimization algorithm and an electric machine differential based yaw stability improvement study. The proposed d-q current signature based SPO fault diagnostic algorithm detects the fault within one electrical cycle. The EMD based extremum seeking slip optimization algorithm reduces stopping distance by 30% compared to hydraulic braking based ABS.

Mountain Meadows Dacite: Oligocene intrusive complex that welds together the Los Angeles Basin, northwestern Peninsular Ranges, and central Transverse Ranges, California

USGS Publications Warehouse

McCulloh, Thane H.; Beyer, Larry A.; Morin, Ronald W.

2001-01-01

Dikes and irregular intrusive bodies of distinctive Oligocene biotite dacite and serially related hornblende latite and felsite occur widely in the central and eastern San Gabriel Mountains, southern California, and are related to the Telegraph Peak granodiorite pluton. Identical dacite is locally present beneath Middle Miocene Topanga Group Glendora Volcanics at the northeastern edge of the Los Angeles Basin, where it is termed Mountain Meadows Dacite. This study mapped the western and southwestern limits of the dacite distribution to understand the provenance of derived redeposited clasts, to perceive Neogene offsets on several large strike-slip faults, to test published palinspastic reconstructions, and to better understand the tectonic boundaries that separate contrasting pre-Tertiary rock terranes where the Peninsular Ranges meet the central and western Transverse Ranges and the Los Angeles Basin. Transported and redeposited clasts of dacite-latite occur in deformed lower Miocene and lower middle Miocene sandy conglomerates (nonmarine, nearshore, and infrequent upper bathyal) close to the northern and northeastern margins of the Los Angeles Basin for a distance of nearly 60 km. Tie-lines between distinctive source suites and clast occurrences indicate that large tracts of the ancestral San Gabriel Mountains were elevated along range-bounding faults as early as 16–15 Ma. The tie-lines prohibit very large strike-slip offsets on those faults. Transport of eroded dacite began south of the range as early as 18 Ma. Published and unpublished data about rocks adjacent to the active Santa Monica-Hollywood-Raymond oblique reverse left-lateral fault indicate that cumulative left slip totals 13–14 km and total offset postdates 7 Ma. This cumulative slip, with assembly of stratigraphic and paleogeographic data, invalidates prior estimates of 60 to 90 km of left slip on these faults beginning about 17–16 Ma. A new and different palinspastic reconstruction of a region southwest of the San Andreas Fault Zone is proposed. Our reconstruction incorporates 20° of clockwise rotation of tracts north of the Raymond Fault from the easternmost Santa Monica Mountains to the Vasquez Creek Fault (San Gabriel south branch). We interpret the Vasquez Creek Fault as a reverse and right-lateral tear fault. Right slip on the tear becomes reverse dip slip on the northeast-striking Clamshell-Sawpit fault complex, interpreted as an offset part of the Mount Lukens Fault. This explains the absence of evidence for lateral offset of the Glendora Volcanics and associated younger marine strata where those are broken farther east by the eastern Sierra Madre reverse fault system. About 34 km of right slip is suggested for all breaks of the San Gabriel fault system. New paleogeographic maps of the Paleogene basin margin and of a Middle Miocene marine embayment and strandline derive in part from our palinspastic reconstruction. These appealingly simple maps fit well with data from the central Los Angeles Basin to the south and southwest.

Disjointness of Stabilizer Codes and Limitations on Fault-Tolerant Logical Gates

NASA Astrophysics Data System (ADS)

Jochym-O'Connor, Tomas; Kubica, Aleksander; Yoder, Theodore J.

2018-04-01

Stabilizer codes are among the most successful quantum error-correcting codes, yet they have important limitations on their ability to fault tolerantly compute. Here, we introduce a new quantity, the disjointness of the stabilizer code, which, roughly speaking, is the number of mostly nonoverlapping representations of any given nontrivial logical Pauli operator. The notion of disjointness proves useful in limiting transversal gates on any error-detecting stabilizer code to a finite level of the Clifford hierarchy. For code families, we can similarly restrict logical operators implemented by constant-depth circuits. For instance, we show that it is impossible, with a constant-depth but possibly geometrically nonlocal circuit, to implement a logical non-Clifford gate on the standard two-dimensional surface code.

Tectonic meaning of anomalous fault-slip strain solutions in the Southern Volcanic Zone of the Andes: insights to assess the structural permeability of the Liquiñe-Ofqui Fault System and the Andean Transverse Faults (39°-40°S)

NASA Astrophysics Data System (ADS)

Sepúlveda, J.; Roquer, T.; Arancibia, G.; Veloso, E. A.; Morata, D.; Molina Piernas, E.

2017-12-01

Oblique subduction between the Nazca and South American plates produces the Southern Volcanic Zone (33-46°S) (SVZ), an active tectono-magmatic-hydrothermal setting. Tectonics of the SVZ is controlled by the Liquiñe-Ofqui Fault System (LOFS) and the Andean Transverse Faults (ATF). The LOFS is an active intra-arc 1200-km-long fault system, with dextral and dextral-normal faults that strike NS-NNE to NE-ENE. The ATF include a group of active NW-striking sinistral faults and morphotectonic lineaments. Here, deformation is partitioned into a margin-parallel and a margin-orthogonal components, accommodated along and across the arc and forearc, respectively. In the inter-seismic period, shortening in the arc is NE-trending, whereas in the co- and post-seismic periods shortening switches to NW-trending. In order to determine the kinematics and style of deformation in the northern termination of the LOFS and its interaction with the ATF, we measured 81 fault-slip data at the Liquiñe (39ºS) and Maihue (40ºS) areas. Here, hot springs occur above fractured granitic rocks, where structural permeability given by fracture meshes is the main hydraulic conductivity. Considering the high sensitivity of fault systems regarding the rupture under prevailing stress and/or fluid overpressure conditions, to stablish past and present strain conditions is critical to assess a potential fractured geothermal system. Results at Liquiñe display two strain regimes (P and T axes): 1) P=259/01, T=169/01; 2) P= 182/23, T= 275/07. Likewise, Maihue shows two regimes: 1) P= 143/12, T=235/07; 2) P=228/12, T= 136/07. In both areas, the first solutions agree with the regional regime within the SVZ, i.e. NE-trending shortening in the arc. However, the second solutions seem to be anomalous with respect to the regional strain regime. At Liquiñe, NS-trending shortening may be associated with a buttress effect at the northern termination of the LOFS. At Maihue, NW-trending shortening may be related to strain changes during the co-seismic period or it is a reminiscence of local strain switches. These anomalous strain solutions should be considered when constraining the tectonics of the SVZ and its role to enhance the subsurface hydraulic conductivity. ACKNOWLEDGEMENTS: FONDAP-CONICYT Project 15090013 (CEGA), VRI-PUENTE P1703/2017 Project.

Deformation during terrane accretion in the Saint Elias orogen, Alaska

USGS Publications Warehouse

Bruhn, R.L.; Pavlis, T.L.; Plafker, G.; Serpa, L.

2004-01-01

The Saint Elias orogen of southern Alaska and adjacent Canada is a complex belt of mountains formed by collision and accretion of the Yakutat terrane into the transition zone from transform faulting to subduction in the northeast Pacific. The orogen is an active analog for tectonic processes that formed much of the North American Cordillera, and is also an important site to study (1) the relationships between climate and tectonics, and (2) structures that generate large- to great-magnitude earthquakes. The Yakutat terrane is a fragment of the North American plate margin that is partly subducted beneath and partly accreted to the continental margin of southern Alaska. Interaction between the Yakutat terrane and the North American and Pacific plates causes significant differences in the style of deformation within the terrane. Deformation in the eastern part of the terrane is caused by strike-slip faulting along the Fairweather transform fault and by reverse faulting beneath the coastal mountains, but there is little deformation immediately offshore. The central part of the orogen is marked by thrusting of the Yakutat terrane beneath the North American plate along the Chugach-Saint Elias fault and development of a wide, thin-skinned fold-and-thrust belt. Strike-slip faulting in this segment may he localized in the hanging wall of the Chugach-Saint Elias fault, or dissipated by thrust faulting beneath a north-northeast-trending belt of active deformation that cuts obliquely across the eastern end of the fold-and-thrust belt. Superimposed folds with complex shapes and plunging hinge lines accommodate horizontal shortening and extension in the western part of the orogen, where the sedimentary cover of the Yakutat terrane is accreted into the upper plate of the Aleutian subduction zone. These three structural segments are separated by transverse tectonic boundaries that cut across the Yakutat terrane and also coincide with the courses of piedmont glaciers that flow from the topographic backbone of the Saint Elias Mountains onto the coastal plain. The Malaspina fault-Pamplona structural zone separates the eastern and central parts of the orogen and is marked by reverse faulting and folding. Onshore, most of this boundary is buried beneath the western or "Agassiz" lobe of the Malaspina piedmont glacier. The boundary between the central fold-and-thrust belt and western zone of superimposed folding lies beneath the middle and lower course of the Bering piedmont glacier. ?? 2004 Geological Society of America.

Post-Neogene tectonism along the Aravalli Range, Rajasthan, India

NASA Astrophysics Data System (ADS)

Sen, Deepawati; Sen, Saurindranath

1983-03-01

The Aravalli Range runs southwest from Delhi for a distance of about 700 km. Its western margin is well defined, but the eastern margin is diffuse. Five geomorphic provinces are recognized in the study area: the western piedmont plains; the ridge and valley province which in the Central Aravallis occurs at two different heights separated by a fault scarp; the plateau province demarcated from the former by a fault scarp, confined to the Southern Aravallis, and occurring for a short stretch at two heights across another fault scarp; the BGC rolling plains east of the Range; and the BGC uplands south of the above. The scarps coincide with Precambrian faults. A series of rapids and water-falls, together with deeply entrenched river courses across the scarps and the youthful aspects of the escarpments with no projecting spurs, or straight river courses along their feet, all point unmistakably to a recent or post-Neogene vertical uplift along pre-existing faults. Presence of knickpoints at a constant distance from the Range in all west-flowing rivers, the ubiquitous terraces, and river courses entrenched within their own flood-plain deposits of thick gritty to conglomeratic sand, are indicative of a constant disturbance with a gradual rise of the Range east of the knickpoint, wherefrom the coarse materials were carried by the fast west-flowing streams. There is a differential uplift across the plateau scarp together with a right-lateral offset. This epeirogenic tectonism is ascribed to the collision of the Eurasian and the subducting Indian plates and to a locking of their continental crusts. By early Pleistocene, with the MBT gradually dying off, continued plate movement caused a flexural bending of the plate by a moment generated at the back, and a possible delinking of the continental crust along the zone of subduction. The felexural bending ripped open the Precambrian regional faults. The differential uplift and the difference in the distances of the nodes on two sides of the major reactivated fault were possibly caused by a difference in the values of the flexural rigidity and the foundation modulus owing to a slight compositional difference of the constiuent rocks in the two sectors.

The Pliocene-Quaternary tectonic evolution of the Cilicia and Adana basins, eastern Mediterranean: Special reference to the development of the Kozan Fault zone

NASA Astrophysics Data System (ADS)

Aksu, A. E.; Walsh-Kennedy, S.; Hall, J.; Hiscott, R. N.; Yaltırak, C.; Akhun, S. D.; Çifçi, G.

2014-05-01

A grid of high-resolution multi-channel seismic reflection profiles allows the detailed mapping of the Kozan Fault zone in the Cilicia and Adana basins. The zone is delineated by an arcuate zone consisting of several ENE-WSW and NNE-SSW striking, closely-spaced high-angle extensional faults which define an ~ 300 km long and 15-20 km-wide “lazy-S” shaped structure along the southeastern fringes of the Taurus Mountain and along the northwestern margins of the Cilicia and Adana basins. In the Cilicia Basin the zone consists of several high-angle faults which exhibit small dip separations on the M-reflector and have tip points situated mainly in the lower and middle portion of the Pliocene-Quaternary succession. In the Adana Basin a family of northeast-striking and southeast dipping extensional faults occurs along the western and northwestern margin of the basin. The faults cut down with relatively steep dip into the ~ 700 ms thick Tortonian and older Miocene successions. Multi-channel seismic reflection profiles show that three prominent seismic markers divide the uppermost Messinian-Recent successions in the Cilicia and Adana basins into three subunits: the uppermost Messinian-Lower Pliocene subunit 1C between the M- and A-reflectors, the Upper Pliocene subunit 1B between the A- and P-reflectors and the Quaternary subunit 1A between the P-reflector and the seafloor. Prominent delta lobes are identified in the seismic profiles that are correlated with the ancestral Göksu River. Isopach maps constructed using depth-converted seismic reflection profiles show clear temporal and spatial variations of the delta lobes of the Göksu River during the latest Messinian-Recent. The uppermost Messinian-Lower Pliocene delta lobe is situated furthest to the northeast whereas the youngest Quaternary lobe is situated furthest to the southwest, with 20-35 km displacement along a northeast-southwest line, which suggests a conservative estimate of 0.43-0.75 cm/yr sinistral slip for the Kozan Fault zone.

Structure of the central Terror Rift, western Ross Sea, Antarctica

USGS Publications Warehouse

Hall, Jerome; Wilson, Terry; Henrys, Stuart

2007-01-01

The Terror Rift is a zone of post-middle Miocene faulting and volcanism along the western margin of the West Antarctic Rift System. A new seismic data set from NSF geophysical cruise NBP04-01, integrated with the previous dataset to provide higher spatial resolution, has been interpreted in this study in order to improve understanding of the architecture and history of the Terror Rift. The Terror Rift contains two components, a structurally-controlled rollover anticlinal arch intruded by younger volcanic bodies and an associated synclinal basin. Offsets and trend changes in fault patterns have been identified, coincident with shifts in the location of depocenters that define rift sub-basins, indicating that the Terror Rift is segmented by transverse structures. Multiple phases of faulting all post-date 17 Ma, including faults cutting the seafloor surface, indicating Neogene rifting and possible modern activity.

The Hula Valley subsurface structure inferred from gravity data

USGS Publications Warehouse

Rybakov, M.; Fleischer, L.; ten Brink, Uri S.

2003-01-01

We use the 3-D gravity inversion technique to model the shape of the Hula basin, a pull-apart basin along the Dead Sea Transform. The interpretation was constrained using the Notera-3-well density logs and current geological knowledge. The model obtained by inversion shows a rhomb-shaped graben filled with approximately 4 km of young sediments in the deepest part of the basin. The reliability of this model was verified using 3-D forward modeling with an accuracy of 0.5 km. Curvature attributes of the gravity field depict the main fault pattern, suggesting that the Hula basin is a subsiding rhomb-shaped graben, bordered by steep-sided, deep basement faults on the western and eastern sides (Qiryat Shemona and Jordan River faults) and by gradual, en-echelon step faults on the southern and northern margins of the basin. ?? 2003 Laser Pages Publishing Ltd.

Middle to Late Devonian-Carboniferous collapse basins on the Finnmark Platform and in the southwesternmost Nordkapp basin, SW Barents Sea

NASA Astrophysics Data System (ADS)

Koehl, Jean-Baptiste P.; Bergh, Steffen G.; Henningsen, Tormod; Faleide, Jan Inge

2018-03-01

The SW Barents Sea margin experienced a pulse of extensional deformation in the Middle-Late Devonian through the Carboniferous, after the Caledonian Orogeny terminated. These events marked the initial stages of formation of major offshore basins such as the Hammerfest and Nordkapp basins. We mapped and analyzed three major fault complexes, (i) the Måsøy Fault Complex, (ii) the Rolvsøya fault, and (iii) the Troms-Finnmark Fault Complex. We discuss the formation of the Måsøy Fault Complex as a possible extensional splay of an overall NE-SW-trending, NW-dipping, basement-seated Caledonian shear zone, the Sørøya-Ingøya shear zone, which was partly inverted during the collapse of the Caledonides and accommodated top-NW normal displacement in Middle to Late Devonian-Carboniferous times. The Troms-Finnmark Fault Complex displays a zigzag-shaped pattern of NNE-SSW- and ENE-WSW-trending extensional faults before it terminates to the north as a WNW-ESE-trending, NE-dipping normal fault that separates the southwesternmost Nordkapp basin in the northeast from the western Finnmark Platform and the Gjesvær Low in the southwest. The WNW-ESE-trending, margin-oblique segment of the Troms-Finnmark Fault Complex is considered to represent the offshore prolongation of a major Neoproterozoic fault complex, the Trollfjorden-Komagelva Fault Zone, which is made of WNW-ESE-trending, subvertical faults that crop out on the island of Magerøya in NW Finnmark. Our results suggest that the Trollfjorden-Komagelva Fault Zone dies out to the northwest before reaching the western Finnmark Platform. We propose an alternative model for the origin of the WNW-ESE-trending segment of the Troms-Finnmark Fault Complex as a possible hard-linked, accommodation cross fault that developed along the Sørøy-Ingøya shear zone. This brittle fault decoupled the western Finnmark Platform from the southwesternmost Nordkapp basin and merged with the Måsøy Fault Complex in Carboniferous times. Seismic data over the Gjesvær Low and southwesternmost Nordkapp basin show that the low-gravity anomaly observed in these areas may result from the presence of Middle to Upper Devonian sedimentary units resembling those in Middle Devonian, spoon-shaped, late- to post-orogenic collapse basins in western and mid-Norway. We propose a model for the formation of the southwesternmost Nordkapp basin and its counterpart Devonian basin in the Gjesvær Low by exhumation of narrow, ENE-WSW- to NE-SW-trending basement ridges along a bowed portion of the Sørøya-Ingøya shear zone in the Middle to Late Devonian-early Carboniferous. Exhumation may have involved part of a large-scale metamorphic core complex that potentially included the Lofoten Ridge, the West Troms Basement Complex and the Norsel High. Finally, we argue that the Sørøya-Ingøya shear zone truncated and decapitated the Trollfjorden-Komagelva Fault Zone during the Caledonian Orogeny and that the western continuation of the Trollfjorden-Komagelva Fault Zone was mostly eroded and potentially partly preserved in basement highs in the SW Barents Sea.

Fast computation of the multivariable stability margin for real interrelated uncertain parameters

NASA Technical Reports Server (NTRS)

Sideris, Athanasios; Sanchez Pena, Ricardo S.

1988-01-01

A novel algorithm for computing the multivariable stability margin for checking the robust stability of feedback systems with real parametric uncertainty is proposed. This method eliminates the need for the frequency search involved in another given algorithm by reducing it to checking a finite number of conditions. These conditions have a special structure, which allows a significant improvement on the speed of computations.

Geomorphic indices indicated differential active tectonics of the Longmen Shan

NASA Astrophysics Data System (ADS)

Gao, M.; Xu, X.; Tan, X.

2012-12-01

The Longmen Shan thrust belt is located at the eastern margin of the Tibetan Plateau. It is a region of rapid active tectonics with high erosion rates and dense vegetation. The structure of the Longmen Shan region is dominated by northeast-trending thrusts and overturned folds that verge to the east and southeast (Burchfiel et al. 1995, Chen and Wilson 1996). The Longmen Shan thrust belt consists of three major faults from west to east: back-range fault, central fault, and frontal-range fault. The Mw 7.9 Wenchuan earthquake ruptured two large thrust faults along the Longmen Shan thrust belt (Xiwei et al., 2009). In this paper, we focus on investigating the spatial variance of tectonic activeness from the back-range fault to the frontal-range fault, particular emphasis on the differential recent tectonic activeness reflected by the hypsometry and the asymmetric factor of the drainage. Results from asymmetric factor indicate the back-rannge thrust fault on the south of the Maoxian caused drainage basins tilted on the hanging wall. For the north of the Maoxian, the strike-slip fault controlled the shapes of the drainage basins. Constantly river capture caused the expansion of the drainage basins which traversed by the fault. The drainages on the central fault and the frontal-range fault are also controlled by the fault slip. The drainage asymmetric factor suggested the central and southern segments of the Longmen Shan are more active than the northern segment, which is coherence with results of Huiping et al. (2010). The results from hypsometry show the back-range fault is the most active fault among the three major faults. Central fault is less active than the back-range fault but more active than the frontal-range fault. Beichuan is identified as the most active area along the central fault. Our geomorphic indices reflect an overall eastward decreasing of tectonic activeness of the Longmen Shan thrust belt.

Crustal structure of a transform plate boundary: San Francisco Bay and the central California continental margin

USGS Publications Warehouse

Holbrook, W.S.; Brocher, T.M.; ten Brink, Uri S.; Hole, J.A.

1996-01-01

Wide-angle seismic data collected during the Bay Area Seismic Imaging Experiment provide new glimpses of the deep structure of the San Francisco Bay Area Block and across the offshore continental margin. San Francisco Bay is underlain by a veneer (<300 m) of sediments, beneath which P wave velocities increase rapidly from 5.2 km/s to 6.0 km/s at 7 km depth, consistent with rocks of the Franciscan subduction assemblage. The base of the Franciscan at-15-18 km depth is marked by a strong wide-angle reflector, beneath which lies an 8- to 10-km-thick lower crust with an average velocity of 6.75??0.15 km/s. The lower crust of the Bay Area Block may be oceanic in origin, but its structure and reflectivity indicate that it has been modified by shearing and/or magmatic intrusion. Wide-angle reflections define two layers within the lower crust, with velocities of 6.4-6.6 km/s and 6.9-7.3 km/s. Prominent subhorizontal reflectivity observed at near-vertical incidence resides principally in the lowermost layer, the top of which corresponds to the "6-s reflector" of Brocher et al. [1994]. Rheological modeling suggests that the lower crust beneath the 6-s reflector is the weakest part of the lithosphere; the horizontal shear zone suggested by Furlong et al. [1989] to link the San Andreas and Hayward/Calaveras fault systems may actually be a broad zone of shear deformation occupying the lowermost crust. A transect across the continental margin from the paleotrench to the Hayward fault shows a deep crustal structure that is more complex than previously realized. Strong lateral variability in seismic velocity and wide-angle reflectivity suggests that crustal composition changes across major transcurrent fault systems. Pacific oceanic crust extends 40-50 km landward of the paleotrench but, contrary to prior models, probably does not continue beneath the Salinian Block, a Cretaceous arc complex that lies west of the San Andreas fault in the Bay Area. The thickness (10 km) and high lower-crustal velocity of Pacific oceanic crust suggest that it was underplated by magmatism associated with the nearby Pioneer seamount. The Salinian Block consists of a 15-km-thick layer of velocity 6.0-6.2 km/s overlying a 5-km-thick, high-velocity (7.0 km/s) lower crust that may be oceanic crust, Cretaceous arc-derived lower crust, or a magmatically underplated layer. The strong structural variability across the margin attests to the activity of strike-slip faulting prior to and during development of the transcurrent Pacific/North American plate boundary around 29 Ma. Copyright 1996 by the American Geophysical Union.

HyFlux - Part I: Regional Modeling of Methane Flux From Near-Seafloor Gas Hydrate Deposits on Continental Margins

NASA Astrophysics Data System (ADS)

MacDonald, I. R.; Asper, V.; Garcia, O. P.; Kastner, M.; Leifer, I.; Naehr, T.; Solomon, E.; Yvon-Lewis, S.; Zimmer, B.

2008-12-01

HyFlux - Part I: Regional modeling of methane flux from near-seafloor gas hydrate deposits on continental margins MacDonald, I.R., Asper, V., Garcia, O., Kastner, M., Leifer, I., Naehr, T.H., Solomon, E., Yvon-Lewis, S., and Zimmer, B. The Dept. of Energy National Energy Technology Laboratory (DOE/NETL) has recently awarded a project entitled HyFlux: "Remote sensing and sea-truth measurements of methane flux to the atmosphere." The project will address this problem with a combined effort of satellite remote sensing and data collection at proven sites in the Gulf of Mexico where gas hydrate releases gas to the water column. Submarine gas hydrate is a large pool of greenhouse gas that may interact with the atmosphere over geologic time to affect climate cycles. In the near term, the magnitude of methane reaching the atmosphere from gas hydrate on continental margins is poorly known because 1) gas hydrate is exposed to metastable oceanic conditions in shallow, dispersed deposits that are poorly imaged by standard geophysical techniques and 2) the consumption of methane in marine sediments and in the water column is subject to uncertainty. The northern GOM is a prolific hydrocarbon province where rapid migration of oil, gases, and brines from deep subsurface petroleum reservoirs occurs through faults generated by salt tectonics. Focused expulsion of hydrocarbons is manifested at the seafloor by gas vents, gas hydrates, oil seeps, chemosynthetic biological communities, and mud volcanoes. Where hydrocarbon seeps occur in depths below the hydrate stability zone (~500m), rapid flux of gas will feed shallow deposits of gas hydrate that potentially interact with water column temperature changes; oil released from seeps forms sea-surface features that can be detected in remote-sensing images. The regional phase of the project will quantify verifiable sources of methane (and oil) the Gulf of Mexico continental margin and selected margins (e.g. Pakistan Margin, South China Sea, and West Africa Margin) world-wide by using the substantial archive of satellite synthetic aperture radar (SAR) images. An automated system for satellite image interpretation will make it possible to process hundreds of SAR images to increase the geographic and temporal coverage. Field programs will quantify the flux and fate of hydrate methane in sediments and the water column.

Phanerozoic geological evolution of Northern and Central Africa: An overview

NASA Astrophysics Data System (ADS)

Guiraud, R.; Bosworth, W.; Thierry, J.; Delplanque, A.

2005-10-01

The principal paleogeographic characteristics of North and Central Africa during the Paleozoic were the permanency of large exposed lands over central Africa, surrounded by northerly and northwesterly dipping pediplanes episodically flooded by epicontinental seas related to the Paleotethys Ocean. The intra-continental Congo-Zaire Basin was also a long-lived feature, as well as the Somali Basin from Late Carboniferous times, in conjunction with the development of the Karoo basins of southern Africa. This configuration, in combination with eustatic sea-level fluctuations, had a strong influence on facies distributions. Significant transgressions occurred during the Early Cambrian, Tremadocian, Llandovery, Middle to Late Devonian, Early Carboniferous, and Moscovian. The Paleozoic tectonic history shows an alternation of long periods of predominantly gentle basin subsidence and short periods of gentle folding and occasionally basin inversion. Some local rift basins developed episodically, located mainly along the northern African-Arabian plate margin and near the West African Craton/Pan-African Belt suture. Several arches or spurs, mainly N-S to NE-SW trending and inherited from late Pan-African fault swarms, played an important role. The Nubia Province was the site of numerous alkaline anorogenic intrusions, starting in Ordovician times, and subsequently formed a large swell. Paleozoic compressional events occurred in the latest Early Cambrian ("Iskelian"), Medial Ordovician to earliest Silurian ("pre-Caradoc" and "Taconian"), the end Silurian ("Early Acadian" or "Ardennian"), mid-Devonian ("Mid-Acadian"), the end Devonian ("Late Acadian" or "Bretonnian"), the earliest Serpukhovian ("Sudetic"), and the latest Carboniferous-earliest Permian ("Alleghanian" or "Asturian"). The strongest deformations, including folding, thrusting, and active strike-slip faulting, were registered in Northwestern Africa during the last stage of the Pan-African Belt development around the West African Craton (end Early Cambrian) and during the polyphased Hercynian-Variscan Orogeny that extended the final closure of the Paleotethys Ocean and resulted in the formation of the Maghrebian and Mauritanides belts. Only gentle deformation affected central and northeastern African during the Paleozoic, the latter remaining a passive margin of the Paleotethys Ocean up to the Early Permian when the development of the Neotethys initiated along the Eastern Mediterranean Basins. The Mesozoic-Cenozoic sedimentary sequence similarly consists of a succession of eustatically and tectonically controlled depositional cycles. Through time, progressive southwards shift of the basin margins occurred, related to the opening of the Neotethys Ocean and to the transgressions resulting from warming of the global climate and associated rise of the global sea level. The Guinean-Nigerian Shield, the Hoggar, Tibesti-Central Cyrenaica, Nubia, western Saudi Arabia, Central African Republic, and other long-lived arches delimited the principal basins. The main tectonic events were the polyphased extension, inversion, and folding of the northern African-Arabian shelf margin resulting in the development of the Alpine Maghrebian and Syrian Arc belts, rifting and drifting along the Central Atlantic, Somali Basins, and Gulf of Aden-Red Sea domains, inversion of the Murzuq-Djado Basin, and rifting and partial inversion along the Central African Rift System. Two major compressional events occurred in the Late Santonian and early Late Eocene. The former entailed folding and strike-slip faulting along the northeastern African-northern Arabian margin (Syrian Arc) and the Central African Fold Belt System (from Benue to Ogaden), and thrusting in Oman. The latter ("Pyrenean-Atlasic") resulted in folding, thrusting, and local metamorphism of the northern African-Arabian plate margin, and rejuvenation of intra-plate fault zones. Minor or more localized compressional deformations took place in the end Cretaceous, the Burdigalian, the Tortonian and Early Quaternary. Recent tectonic activity is mainly concentrated along the Maghrebian Alpine Belt, the offshore Nile Delta, the Red Sea-East African Rifts Province, the Aqaba-Dead Sea-Bekaa sinistral strike-slip fault zone, and some major intra-plate fault zones including the Guinean-Nubian, Aswa, and central Sinai lineaments. Large, long-lived magmatic provinces developed in the Egypt-Sudan confines (Nubia), in the Hoggar-Air massifs, along the Cameroon Line and Nigerian Jos Plateau, and along the Levant margin, resulting in uplifts that influenced the paleogeography. Extensive tholeiitic basaltic magmatism at ˜200 Ma preceded continental break-up in the Central Atlantic domain, while extensive alkaline to transitional basaltic magmatism accompanied the Oligocene to Recent rifting along the Red Sea-Gulf of Aden-East African rift province.

MER surface fault protection system

NASA Technical Reports Server (NTRS)

Neilson, Tracy

2005-01-01

The Mars Exploration Rovers surface fault protection design was influenced by the fact that the solar-powered rovers must recharge their batteries during the day to survive the night. the rovers needed to autonomously maintain thermal stability, initiate safe and reliable communication with orbiting assets or directly to Earth, while maintaining energy balance. This paper will describe the system fault protection design for the surface phase of the mission.

Detailed interpretation of aeromagnetic data from the Patagonia Mountains area, southeastern Arizona

USGS Publications Warehouse

Bultman, Mark W.

2015-01-01

Euler deconvolution depth estimates derived from aeromagnetic data with a structural index of 0 show that mapped faults on the northern margin of the Patagonia Mountains generally agree with the depth estimates in the new geologic model. The deconvolution depth estimates also show that the concealed Patagonia Fault southwest of the Patagonia Mountains is more complex than recent geologic mapping represents. Additionally, Euler deconvolution depth estimates with a structural index of 2 locate many potential intrusive bodies that might be associated with known and unknown mineralization.

Fault-scale controls on rift geometry: the Bilila-Mtakataka Fault, Malawi

NASA Astrophysics Data System (ADS)

Hodge, M.; Fagereng, A.; Biggs, J.; Mdala, H. S.

2017-12-01

Border faults that develop during initial stages of rifting determine the geometry of rifts and passive margins. At outcrop and regional scales, it has been suggested that border fault orientation may be controlled by reactivation of pre-existing weaknesses. Here, we perform a multi-scale investigation on the influence of anisotropic fabrics along a major developing border fault in the southern East African Rift, Malawi. The 130 km long Bilila-Mtakataka fault has been proposed to have slipped in a single MW 8 earthquake with 10 m of normal displacement. The fault is marked by an 11±7 m high scarp with an average trend that is oblique to the current plate motion. Variations in scarp height are greatest at lithological boundaries and where the scarp switches between following and cross-cutting high-grade metamorphic foliation. Based on the scarp's geometry and morphology, we define 6 geometrically distinct segments. We suggest that the segments link to at least one deeper structure that strikes parallel to the average scarp trend, an orientation consistent with the kinematics of an early phase of rift initiation. The slip required on a deep fault(s) to match the height of the current scarp suggests multiple earthquakes along the fault. We test this hypothesis by studying the scarp morphology using high-resolution satellite data. Our results suggest that during the earthquake(s) that formed the current scarp, the propagation of the fault toward the surface locally followed moderately-dipping foliation well oriented for reactivation. In conclusion, although well oriented pre-existing weaknesses locally influence shallow fault geometry, large-scale border fault geometry appears primarily controlled by the stress field at the time of fault initiation.

Strike-slip faulting at Thebes Gap, Missouri and Illinois; implications for New Madrid tectonism

USGS Publications Warehouse

Harrison, Richard W.; Schultz, Art

1994-01-01

Numerous NNE and NE striking strike-slip faults and associated normal faults, folds, and transtensional grabens occur in the Thebes Gap area of Missouri and Illinois. These structures developed along the northwestern margin of the buried Reelfoot rift of Precambrian-Cambrian age at the northern edge of the Mississippi embayment. They have had a long-lived and complex structural history. This is an area of recent moderate seismicity, approximately 45 km north of the New Madrid seismic zone. Stratigraphic evidence suggests that these faults were active during the Middle Ordovician. They were subsequently reactivated between the Early Devonian and Late Cretaceous, probably in response to both the Acadian and Ouachita orogenies. Deformation during this period was characterized by strongly faulted and folded Ordovician through Devonian rocks. In places, these deformed rocks are overlain with angular unconformity by undeformed Cretaceous strata. Fault motion is interpreted as dominantly strike slip. A still younger period of reactivation involved Late Cretaceous and Cenozoic formations as young as the Miocene or Pliocene Mounds Gravel. These formations have experienced both minor high-angle normal faulting and subsequent major, right-lateral strike-slip faulting. En echelon north-south folds, ENE striking normal faults, regional fracture patterns, and drag folds indicate the right-lateral motion for this major episode of faulting which predates deposition of Quaternary loess. Several nondefinitive lines of evidence suggest Quaternary faulting. Similar fault orientations and kinematics, as well as recent seismicity and proximity, clearly suggest a structural relationship between deformation at Thebes Gap and tectonism associated with the New Madrid area.

Effects induced by an earthquake on its fault plane:a boundary element study

NASA Astrophysics Data System (ADS)

Bonafede, Maurizio; Neri, Andrea

2000-04-01

Mechanical effects left by a model earthquake on its fault plane, in the post-seismic phase, are investigated employing the `displacement discontinuity method'. Simple crack models, characterized by the release of a constant, unidirectional shear traction are investigated first. Both slip components-parallel and normal to the traction direction-are found to be non-vanishing and to depend on fault depth, dip, aspect ratio and fault plane geometry. The rake of the slip vector is similarly found to depend on depth and dip. The fault plane is found to suffer some small rotation and bending, which may be responsible for the indentation of a transform tectonic margin, particularly if cumulative effects are considered. Very significant normal stress components are left over the shallow portion of the fault surface after an earthquake: these are tensile for thrust faults, compressive for normal faults and are typically comparable in size to the stress drop. These normal stresses can easily be computed for more realistic seismic source models, in which a variable slip is assigned; normal stresses are induced in these cases too, and positive shear stresses may even be induced on the fault plane in regions of high slip gradient. Several observations can be explained from the present model: low-dip thrust faults and high-dip normal faults are found to be facilitated, according to the Coulomb failure criterion, in repetitive earthquake cycles; the shape of dip-slip faults near the surface is predicted to be upward-concave; and the shallower aftershock activity generally found in the hanging block of a thrust event can be explained by `unclamping' mechanisms.

Neotectonic of Southern Brazilian Passive Margin: evidence from field and remote sensing studies

NASA Astrophysics Data System (ADS)

Riffel, S. B.; Fernandes, L. A. D.

2017-12-01

Canyons and structured-controlled coastal lagoons along Southern Brazil show morphotectonic evidence of an active response from the compressive strain on rifted continental margins. Considering the current main stress directions (E-W) and co-axial deformation, the most likely faults to be reactivated are the N45E and N45W trending systems. The area set in the eastern limit of the Paraná-Etendeka large igneous province, where a fault scarp marks regressive erosion and exposes a succession of fine-grained sediments belonging to the Pelotas Offshore Basin. Extrusion of enormous volumes of lavas provoked isostatic compensation during the Lower Cretaceous followed by the break-up of the Gondwanaland and the development of a volcanic passive margin. At this latitude (29°30´S), the Paraná Basin occurs as a promontory and extends below the Pelotas Offshore Basin, which sets in a continental crust. Regionally, this area is characterized by a down-warping known as Torres Syncline, limited towards the North by the outcropping of Permian sedimentary units, whilst the Serra Geral escarpment is recessed into the interior. The abrupt scarp on acidic volcanic rocks is cut-across by lineaments produced by reactivation of pre-existing faults, resulting in one of the most remarkable sequences of canyons in South America (Aparados da Serra National Park). Along the V-shaped valleys, several sets of triangular facets and suspended valleys are common. Capture, and flow of streams are controlled by the N45-70E and N45-70W trending lineaments. Besides, fault scarps showing displacement of up to 2-3 m, alluvial fan sediments, and transported soil with several sets of fracture represent a geomorphological evidence of reactivation. At the coastal plain, four depositional episodes have developed along the last 400 ka, functioning as barrier-lagoon systems. In this region, linear NE and NW lineaments constrained the shape of Holocene lagoons and affected the distribution of wet lands and dunes. Epicenters of low-intensity earthquakes (<4.0) have been registered by a local array of stations, during 9 years, and are distributed along some of the NE and NW trending lineaments, suggesting reactivation of these older faults. This seems to be in agreement with geomorphological evidence such as the development of young valleys and streams.

Stability Metrics for Simulation and Flight-Software Assessment and Monitoring of Adaptive Control Assist Compensators

NASA Technical Reports Server (NTRS)

Hodel, A. S.; Whorton, Mark; Zhu, J. Jim

2008-01-01

Due to a need for improved reliability and performance in aerospace systems, there is increased interest in the use of adaptive control or other nonlinear, time-varying control designs in aerospace vehicles. While such techniques are built on Lyapunov stability theory, they lack an accompanying set of metrics for the assessment of stability margins such as the classical gain and phase margins used in linear time-invariant systems. Such metrics must both be physically meaningful and permit the user to draw conclusions in a straightforward fashion. We present in this paper a roadmap to the development of metrics appropriate to nonlinear, time-varying systems. We also present two case studies in which frozen-time gain and phase margins incorrectly predict stability or instability. We then present a multi-resolution analysis approach that permits on-line real-time stability assessment of nonlinear systems.

Finite-time fault tolerant attitude stabilization control for rigid spacecraft.

PubMed

Huo, Xing; Hu, Qinglei; Xiao, Bing

2014-03-01

A sliding mode based finite-time control scheme is presented to address the problem of attitude stabilization for rigid spacecraft in the presence of actuator fault and external disturbances. More specifically, a nonlinear observer is first proposed to reconstruct the amplitude of actuator faults and external disturbances. It is proved that precise reconstruction with zero observer error is achieved in finite time. Then, together with the system states, the reconstructed information is used to synthesize a nonsingular terminal sliding mode attitude controller. The attitude and the angular velocity are asymptotically governed to zero with finite-time convergence. A numerical example is presented to demonstrate the effectiveness of the proposed scheme. © 2013 Published by ISA on behalf of ISA.

Link between the northward extension of Great Sumatra Fault and continental rifting in the Andaman Sea: new results from seismic reflection studies

NASA Astrophysics Data System (ADS)

Singh, S. C.; Moeremans, R. E.; McArdle, J.; Johansen, K.

2012-12-01

The Great Sumatra Fault (GSF) traverses the main land Sumatra from Sunda Strait in the southeast to Banda Aceh in the northwest for about 1900 km, and defines the present day plate boundary between the Sunda Plate in the north and Burmese Sliver Plate in the south. It is formed due to the oblique subduction of the Indo-Australian Plate beneath the Sunda Plate. It has been well studied on land but is poorly studied north of Banda Aceh in the Andaman Sea. Its study is further complicated by the presence of volcanic arc in its vicinity and its interaction with the West Andaman Fault (WAF) further north. Here we present deep seismic reflection images along the northward extension of the GSF over 700 km until it joins the Andaman Spreading Centre and interpret these images in the light of earthquake, gravity and bathymetry data. We find that the GSF has two strands between Banda Aceh and Nicobar Island: a transpression in the south and a deep narrow active rift basin in the north dotted with volcanoes in the center, suggesting that the volcanic arc is coincident with the rifting. Further north of Nicobar Island, an active strike-slip fault cuts through a deep rifted basin until its intersection with Andaman Sea Spreading Centre. The volcanic arc lies just east of the basin. The western margin of this basin seems to be a rifted continental margin, tilted westward flooring the Andaman-Nicobar forearc basin, which was once a part of Malaya Peninsula, suggesting that a significant parts of the Andaman-Nicobar forearc system is underlain by the Sunda continental crust. The Andaman-Nicobar forearc basin is bounded in the west by backthrusts, similar to the West Andaman and Mentawai faults bounding the Aceh and Mentawai forearc basins in the south. The cluster of seismicity after the 2004 great Andaman-Sumatra earthquake just north of Nicobar Island coincides with the intersection of two NW-SE and N-S trending strike-slip fault systems. Some of hypocentre of these earthquakes lie in the mantle down to 30 km depth, which along with the presence of volcanic arc just 15 km east of these faults, suggest that there is no generic link between the strike-slip fault and volcanic arc.

Seafloor morphology related to recent tectonics in the Alboran Sea Basin

NASA Astrophysics Data System (ADS)

Vázquez, Juan-Tomás; Estrada, Ferran; Vegas, Ramon; Ercilla, Gemma; Medialdea, Teresa; d'Acremont, Elia; Alonso, Belen; Fernández-Salas, Luis-Miguel; Gómez-Ballesteros, María; Somoza, Luis; Bárcenas, Patricia; Palomino, Desirée; Gorini, Christian

2014-05-01

A detailed geomorphological study of the northern part of the Alboran Sea Basin has been realized based on the combined analysis of multibeam swath bathymetric data and medium to very high resolution seismic profiles (singled Sparker, Airgun, TOPAS and Atlas PARASOUND P35). This has enabled us to define several tectonic-related seafloor features and their role in the recent tectonics. The observed morpho-tectonic features correspond to: i) lineal scarps with a wide range of dimensions and following several trends ,WNW-ESE, NE-SW, NNE-SSW and N-S; ii) NE-SW to NNE-SSW-oriented compressive ridges; iii) ENE-WSW to NE-SW-striking antiforms; iv) NNE-SSW-oriented lineal depressions; v) rhomb-shaped depressions; vi) lineal valleys, canyons and gullies with WNW-ESE, and N-S orientations; and vii) N-S directed dissected valleys, canyons and gullies. Three families of faults and related folds, with NE-SW, WNW-ESE and NNE-SSW to N-S have been interpreted within this geomorphological scheme. The NE-SW family corresponds to: a) major scarps in both flanks of the Alboran Ridge and b) the offshore prolongation of La Serrata Fault, and both have been considered as a set of sinistral strike-slip faults. To this family, some compressive ridges, antiforms and occasionally reverse faults have been correlated. The WNW-ESE family corresponds to a set of faulted valleys (occasionally with rhomb-shaped depressions), fault scarps and linear inflection points occurring in the northern Alboran margin and the Yusuf-Habibas corridor. This family has been interpreted as transtensive dextral strike-slip faults. The NNE-SSW to N-S family corresponds to a penetrative system of linear fault scarps and tectonic depressions that cross-cut the Alboran Ridge and the Djibouti-Motril marginal plateau. This family can be considered as more recent since it offsets the other two families and shows a minor importance with regard to the main reliefs. This communication is a contribution to the Spanish R + D + I projects MONTERA (CTM2009-14157-C02) and MOWER (CTM2012-39599-C03), the Project MOSAIC of scientific excellence of Andalusia(P06-RNM-01594) and the European ESF projects EUROFLEET SARAS and TOPOMED_SPAIN (CGL2008-03474-E).

New Holocene Slip-rate Sites Along the Mojave San Andreas Fault Near Palmdale, CA

NASA Astrophysics Data System (ADS)

Young, E. K.; Cowgill, E.; Scharer, K. M.

2016-12-01

The slip rate for the Mojave San Andreas fault (MSAF) is poorly known: the long-term ( 413ky) geologic rate is as high as 37mm/yr [1] while the geodetic slip rate is as low as 15mm/yr [2]. To determine the Holocene-average rate for the MSAF, we investigated several offset landforms near Palmdale, CA using detailed surficial mapping and 14C analyses of charcoal collected from hand-dug excavations. Site X-12 preserves two offset markers sourced from a north-flowing catchment south of the fault. One is a terrace riser cut into older alluvium that is abutted by the eastern margin of a Qf3 fan and is displaced by 75 m. Offset of the riser and the alluvium generated a north-facing fault-scarp that was eroded to form a small fan on top of the eastern margin of the Qf3 fan. The second offset is a beheaded channel that is incised into the Qf3 fan north of the fault and is displaced 50m, and thus formed after the riser was offset by 25m. To date these landforms we opened 5 excavations at the site, with emphasis on the beheaded channel. Dates from within the Qf3 fan south/upstream of the fault and abandoned bedload in the beheaded channel give maximum and minimum ages for the channel incision of 1500calBP and 600calBP, respectively, implying a rate ≥33mm/yr. Future work seeks to date post-abandonment channel-fill deposits and the upper and lower bounds on the terrace riser. At a second site, Ranch Center, a north-flowing stream cut across a shutter ridge north of the fault and was then offset and deflected 80m before cutting a new channel across the fault. Future work here seeks to date the bases of the alluvial fans deposited by the abandoned and active channels to obtain maximum and minimum ages for the 80 m offset, respectively. Rates from these sites should help to better define the Holocene slip rate on the MSAF. 1) Matmon et al., 2005, GSAB. v. 117 p. 795 2) Becker et al., 2005, Geoph.. J. Int., v. 160 p. 634

A remote sensing study of active folding and faulting in southern Kerman province, S.E. Iran

NASA Astrophysics Data System (ADS)

Walker, Richard Thomas

2006-04-01

Geomorphological observations reveal a major oblique fold-and-thrust belt in Kerman province, S.E. Iran. The active faults appear to link the Sabzevaran right-lateral strike-slip fault in southeast Iran to other strike-slip faults within the interior of the country and may provide the means of distributing right-lateral shear between the Zagros and Makran mountains over a wider region of central Iran. The Rafsanjan fault is manifest at the Earth's surface as right-lateral strike-slip fault scarps and folding in alluvial sediments. Height changes across the anticlines, and widespread incision of rivers, are likely to result from hanging-wall uplift above thrust faults at depth. Scarps in recent alluvium along the northern margins of the folds suggest that the thrusts reach the surface and are active at the present-day. The observations from Rafsanjan are used to identify similar late Quaternary faulting elsewhere in Kerman province near the towns of Mahan and Rayen. No instrumentally recorded destructive earthquakes have occurred in the study region and only one historical earthquake (Lalehzar, 1923) is recorded. In addition GPS studies show that present-day rates of deformation are low. However, fault structures in southern Kerman province do appear to be active in the late Quaternary and may be capable of producing destructive earthquakes in the future. This study shows how widely available remote sensing data can be used to provide information on the distribution of active faulting across large areas of deformation.