Study of a conceptual nuclear energy center at Green River, Utah. Power demand, load center assessment and transmission

DOE Office of Scientific and Technical Information (OSTI.GOV)

Smith, D.R.; Thaik, A.; Pingel, P.

This document constitutes a segment of a feasibility study investigating the ramification of constructing a nuclear energy center in an arid western region. In this phase of the study. The projected power demands and load center locations were reviewed and assessed. Alternative transmission systems were analysed and a conceptual transmission for bulk power transportation is proposed with potential line routes. Environmental impacts of the proposed transmission were also identified.

Conceptual design study of a V/STOL lift fan commercial short haul transport

NASA Technical Reports Server (NTRS)

Knight, R. G.; Powell, W. V., Jr.; Prizlow, J. A.

1973-01-01

Conceptual designs of V/STOL lift fan commercial short haul transport aircraft for the 1980-85 time period were studied to determine their technical and economic feasibility. The engine concepts included both integral and remote fans. The scope of the study included definition of the hover control concept for each propulsion system, aircraft design, mass properties, cruise performance, noise and ride qualities evaluation. Economic evaluation was also studied on the basis of direct-operating costs and route structure.

Conceptual design of a V/STOL lift fan commercial short haul transport

NASA Technical Reports Server (NTRS)

1973-01-01

Conceptual designs of V/STOL lift-fan commercial short-haul transport aircraft for the 1980-85 time period were studied to determine their technical and economic feasibility. Engine concepts studied included both integral remote fans. The scope of the study included definition of the hover control concept for each propulsion system, aircraft design, aircraft mass properties, cruise performance noise, and ride qualities evaluation. Economic evaluation was also studied on a basis of direct operating cost and route structure.

Feasibility study of liquid pool burning in reduced gravity

NASA Technical Reports Server (NTRS)

Kanury, A. M.

1979-01-01

The feasibility of conducting experiments in the Spacelab on ignition and flame spread with liquid fuel pools which are initially at a temperature lower than the fuel's flash point temperature was studied. Theories were developed for the ignition and flame spread processes, and experiments were conducted to understand the factors influencing the ignition process and the spread rate. The results were employed to devise a conceptual Spacelab experiment which is expected to be feasible for a safe conduct and to be suitable for obtaining crucial data on the concerned processes.

Integrated Power/Attitude Control System (IPACS) study. Volume 1: Feasibility studies. [application of flywheels for power storage and generation

NASA Technical Reports Server (NTRS)

Notti, J. E.; Cormack, A., III; Schmill, W. C.

1974-01-01

An Integrated Power/Attitude Control System (IPACS) concept consisting of an array of spinning flywheels, with or without gimbals, capable of performing the dual function of power storage and generation, as well as attitude control has been investigated. This system provides attitude control through momentum storage, and replaces the storage batteries onboard the spacecraft. The results of the investigation are presented in two volumes. The trade-off studies performed to establish the feasibility, cost effectiveness, required level of development, and boundaries of application of IPACS to a wide variety of spacecraft are discussed. The conceptual designs for a free-flying research application module (RAM), and for a tracking and data relay satellite (TDRS) are presented. Results from dynamic analyses and simulations of the IPACS conceptual designs are included.

Conceptual design and feasibility evaluation model of a 10 to the 8th power bit oligatomic mass memory. Volume 2: Feasibility evaluation model

NASA Technical Reports Server (NTRS)

Horst, R. L.; Nordstrom, M. J.

1972-01-01

The partially populated oligatomic mass memory feasibility model is described and evaluated. A system was desired to verify the feasibility of the oligatomic (mirror) memory approach as applicable to large scale solid state mass memories.

Conceptual design studies of candidate V/STOL lift fan commercial short haul transport for 1980 - 1985 V/STOL lift fan study

NASA Technical Reports Server (NTRS)

Eldridge, W. M.; Ferrell, J. A.; Mckee, J. W.; Wayne, J. E., Jr.; Zabinsky, J. M.

1973-01-01

Conceptual designs of V/STOL lift fan commercial short haul transport aircraft for the 1980-85 time period were studied to determine their technical and economic feasibility. The engine concepts included both integral and remote fans. The scope of the study included definition of the hover control concept for each propulsion system, aircraft design, aircraft mass properties, cruise performance, noise and ride qualities evaluation. Economic evaluating was also studied on a basis of direct operating costs and route structure.

Conceptual study and key technology development for Mars Aeroflyby sample collection

NASA Astrophysics Data System (ADS)

Fujita, K.; Ozawa, T.; Okudaira, K.; Mikouchi, T.; Suzuki, T.; Takayanagi, H.; Tsuda, Y.; Ogawa, N.; Tachibana, S.; Satoh, T.

2014-01-01

Conceptual study of Mars Aeroflyby Sample Collection (MASC) is conducted as a part of the next Mars exploration mission currently entertained in Japan Aerospace Exploration Agency. In the mission scenario, an atmospheric entry vehicle is flown into the Martian atmosphere, collects the Martian dust particles as well as atmospheric gases during the guided hypersonic flight, exits the Martian atmosphere, and is inserted into a parking orbit from which a return system departs for the earth to deliver the dust and gas samples. In order to accomplish a controlled flight and a successful orbit insertion, aeroassist orbit transfer technologies are introduced into the guidance and control system. System analysis is conducted to assess the feasibility and to make a conceptual design, finding that the MASC system is feasible at the minimum system mass of 600 kg approximately. The aerogel, which is one of the candidates for the dust sample collector, is assessed by arcjet heating tests to examine its behavior when exposed to high-temperature gases, as well as by particle impingement tests to evaluate its dust capturing capability.

Phase A design study of microgravity fluoride fiber puller

NASA Technical Reports Server (NTRS)

Workman, Gary L.; Smith, Guy A.; Kosten, Susan

1994-01-01

Improved transmission properties for fluoride fibers due to space processing has great potential for commercial benefits. Phase A design study will determine conceptual feasibility and provide initial definition of the technical requirements and design issues for space.

Conceptual design study of 1985 commercial VTOL transports that utilize rotors

NASA Technical Reports Server (NTRS)

Kefford, N. F. K.; Munch, C. L.

1975-01-01

Conceptual design studies of pure and compound helicopter commercial short-haul transport aircraft for initial fabrication in 1980 were performed to determine their technical and economic feasibility. One-hundred-passenger configurations were optimized for minimum direct operating cost consistent with producibility and marketability, with emphasis on proper account of mass properties, performance and handling qualities adequacy, and suppression of internal and external noise. The effect of external noise constraints was assessed, in terms of gross weight and direct operating cost, for each aircraft.

A study of system requirements for Phobos/Deimos missions. Volume 2: Phase 1 results, satellite rendezvous and landing missions

NASA Technical Reports Server (NTRS)

1972-01-01

The feasibility of a satellite rendezvous, landing, and roving mission to the Martian satellites Phobos and Deimos is considered. Mission-oriented analysis, systems analysis, and conceptual design studies are presented.

Feasibility of Implementing an All-Volunteer Force for the ROK Armed Forces

DTIC Science & Technology

2007-03-01

Korea’s current military/economic/political/social factors for voluntary recruitment through an open-systems conceptual model. Results indicate that the...recruitment through an open-systems conceptual model. Results indicate that the draft should be maintained for the near future, but this does not...7 A. A CONCEPTUAL MODEL FOR DEFENSE ORGANIZATION

Cable Television and Health Promotion: A Feasibility Study with Arthritis Patients.

ERIC Educational Resources Information Center

Katz, David

1985-01-01

Describes a study undertaken to ascertain the extent to which arthritis patients could be targeted by arthritis-related programming over a local cable system. Some conceptual and practical issues involved in targeting chronic patient groups for health programming are discussed. (Author/CT)

Feasibility and systems definition study for Microwave Multi-Application Payload (MMAP)

NASA Technical Reports Server (NTRS)

Horton, J. B.; Allen, C. C.; Massaro, M. J.; Zemany, J. L.; Murrell, J. W.; Stanhouse, R. W.; Condon, G. P.; Stone, R. F.; Swana, J.; Afifi, M.

1977-01-01

Work completed on three Shuttle/Spacelab experiments is examined: the Adaptive Multibeam Phased Array Antenna (AMPA) Experiment, Electromagnetic Environment Experiment (EEE) and Millimeter Wave Communications Experiment (MWCE). Results included the definition of operating modes, sequence of operation, radii of operation about several ground stations, signal format, foot prints of typical orbits and preliminary definition of ground and user terminals. Conceptual hardware designs, Spacelab interfaces, data handling methods, experiment testing and verification studies were included. The MWCE-MOD I was defined conceptually for a steerable high gain antenna.

Enabling Rapid and Robust Structural Analysis During Conceptual Design

NASA Technical Reports Server (NTRS)

Eldred, Lloyd B.; Padula, Sharon L.; Li, Wu

2015-01-01

This paper describes a multi-year effort to add a structural analysis subprocess to a supersonic aircraft conceptual design process. The desired capabilities include parametric geometry, automatic finite element mesh generation, static and aeroelastic analysis, and structural sizing. The paper discusses implementation details of the new subprocess, captures lessons learned, and suggests future improvements. The subprocess quickly compares concepts and robustly handles large changes in wing or fuselage geometry. The subprocess can rank concepts with regard to their structural feasibility and can identify promising regions of the design space. The automated structural analysis subprocess is deemed robust and rapid enough to be included in multidisciplinary conceptual design and optimization studies.

Gateway Arch Circulator Conceptual Feasibility Study : Jefferson National Expansion Memorial

DOT National Transportation Integrated Search

2015-03-01

The Jefferson National Expansion Memorial (JEFF) is undergoing major design changes as part of the City Arch River 2015 project (CAR) that will impact access for park visitors. The park and stakeholders are considering a circulator system to facilita...

AGRI Grain Power ethanol-for-fuel project feasibility-study report. Volume I. Project conceptual design

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1981-04-01

The AGRI GRAIN POWER (AGP) Project, hereafter referred to as the Project, was formed to evaluate the commercial viability and assess the desireability of implementing a large grain based grass-roots anhydrous ethanol fuel project to be sited near Des Moines, Iowa. This report presents the results of a Project feasibility evaluation. The Project concept is based on involving a very strong managerial, financial and technical joint venture that is extremely expert in all facets of planning and implementing a large ethanol project; on locating the ethanol project at a highly desireable site; on utilizing a proven ethanol process; and onmore » developing a Project that is well suited to market requirements, resource availability and competitive factors. The Project conceptual design is presented in this volume.« less

The perceived feasibility and acceptability of a conceptually challenging exercise training program in older adults.

PubMed

Miller, Clint T; Teychenne, Megan; Maple, Jaimie-Lee

2018-01-01

Exercise training is an essential component of falls prevention strategies, but they do not fully address components of physical function that leads to falls. The training approaches to achieve this may not be perceived as appropriate or even feasible in older adults. This study aims to assess the perceived feasibility and acceptability of novel exercise training approaches not usually prescribed to older adults. Fourteen adults were exposed to conceptually and physically demanding exercises. Interviews were then conducted to determine perceptions and acceptability of individual exercise tasks. Qualitative thematic analysis was used to identify themes. Safety and confidence, acceptability, and population participation were the key themes identified. Staff knowledge, presence, program design, and overt safety equipment were important for alleviating initial apprehension. Although physically demanding, participants expressed satisfaction when challenged. Prior disposition, understanding the value, and the appeal of novel exercises were perceived to influence program engagement. Given the evidence for acceptability, this type of training is feasible and may be appropriate as part of an exercise training program for older adults. Further research should be conducted to confirm that the physical adaptations to exercise training approaches as presented in this study occur in a similar manner to that observed in younger adults, and to also determine whether these adaptations lead to prolonged independence and reduced falls in older adults compared to usual care.

Feasibility and systems definition study for microwave multi-application payload (MMAP)

NASA Technical Reports Server (NTRS)

Horton, J. B.; Allen, C. C.; Massaro, M. J.; Zemany, J. L.; Murrell, J. W.; Stanhouse, R. W.; Condon, G. P.; Stone, R. F.

1977-01-01

There were three Shuttle/Spacelab experiments: adaptive multibeam phased array antenna (AMPA) experiment, electromagnetic environment experiment (EEE), and millimeter wave communications experiment (MWCE). Work on the AMPA experiment was completed. Results included are definition of operating modes, sequence of operation, radii of operation about several ground stations, signal format, foot prints of typical orbits and preliminary definition of ground and user terminals. Definition of the MOD I EEE included conceptual hardware designs, spacelab interfaces, preliminary data handling methods, experiment tests and verification, and EMC studies. The MWCE was defined conceptually for a steerable high gain antenna.

The Implementation of Blended Learning Using Android-Based Tutorial Video in Computer Programming Course II

NASA Astrophysics Data System (ADS)

Huda, C.; Hudha, M. N.; Ain, N.; Nandiyanto, A. B. D.; Abdullah, A. G.; Widiaty, I.

2018-01-01

Computer programming course is theoretical. Sufficient practice is necessary to facilitate conceptual understanding and encouraging creativity in designing computer programs/animation. The development of tutorial video in an Android-based blended learning is needed for students’ guide. Using Android-based instructional material, students can independently learn anywhere and anytime. The tutorial video can facilitate students’ understanding about concepts, materials, and procedures of programming/animation making in detail. This study employed a Research and Development method adapting Thiagarajan’s 4D model. The developed Android-based instructional material and tutorial video were validated by experts in instructional media and experts in physics education. The expert validation results showed that the Android-based material was comprehensive and very feasible. The tutorial video was deemed feasible as it received average score of 92.9%. It was also revealed that students’ conceptual understanding, skills, and creativity in designing computer program/animation improved significantly.

FUEL CELL OPERATION ON ANAEROBIC DIGESTER GAS: CONCEPTUAL DESIGN AND ASSESSMENT

EPA Science Inventory

The conceptual design of a fuel cell (FC) system for operation on anaerobic digester gas (ADG) is described and its economic and environmental feasibility is projected. ADG is produced at water treatment plants during the process of treating sewage anaerobically to reduce solids....

Prioritizing sites for conservation based on similarity to historical baselines and feasibility of protection.

PubMed

Popejoy, Traci; Randklev, Charles R; Neeson, Thomas M; Vaughn, Caryn C

2018-05-08

The shifting baseline syndrome concept advocates for the use of historical knowledge to inform conservation baselines, but does not address the feasibility of restoring sites to those baselines. In many regions, conservation feasibility varies among sites due to differences in resource availability, statutory power, and land-owner participation. We use zooarchaeological records to identify a historical baseline of the freshwater mussel community's composition before Euro-American influence at a river-reach scale. We evaluate how the community reference position and the feasibility of conservation might enable identification of sites where conservation actions would preserve historically representative communities and be likely to succeed. We first present a conceptual model that incorporates community information and landscape factors to link the best conservation areas to potential cost and conservation benefits. Using fuzzy ordination, we identify modern mussel beds that are most like the historical baseline. We then quantify the housing density and land use near each reach to estimate feasibility of habitat restoration. Using our conceptual framework, we identify reaches that have high conservation value (i.e., reaches that contain the best mussel beds) and where restoration actions would be most likely to succeed. Reaches above Lake Belton in central Texas, U.S.A. were most similar in species composition and relative abundance to zooarchaeological sites. A subset of these mussel beds occurred in locations where conservation actions appear to be most feasible. This study demonstrates how to use zooarchaeological data (biodiversity data often readily available) and estimates of conservation feasibility to inform conservation priorities at a local spatial scale. This article is protected by copyright. All rights reserved.

Conceptual design study of a visual system for a rotorcraft simulator and some advances in platform motion utilization

NASA Technical Reports Server (NTRS)

Sinacori, J. B.

1980-01-01

A conceptual design of a visual system for a rotorcraft flight simulator is presented. Also, drive logic elements for a coupled motion base for such a simulator are given. The design is the result of an assessment of many potential arrangements of electro-optical elements and is a concept considered feasible for the application. The motion drive elements represent an example logic for a coupled motion base and is essentially an appeal to the designers of such logic to combine their washout and braking functions.

Defining Feasibility and Pilot Studies in Preparation for Randomised Controlled Trials: Development of a Conceptual Framework.

PubMed

Eldridge, Sandra M; Lancaster, Gillian A; Campbell, Michael J; Thabane, Lehana; Hopewell, Sally; Coleman, Claire L; Bond, Christine M

2016-01-01

We describe a framework for defining pilot and feasibility studies focusing on studies conducted in preparation for a randomised controlled trial. To develop the framework, we undertook a Delphi survey; ran an open meeting at a trial methodology conference; conducted a review of definitions outside the health research context; consulted experts at an international consensus meeting; and reviewed 27 empirical pilot or feasibility studies. We initially adopted mutually exclusive definitions of pilot and feasibility studies. However, some Delphi survey respondents and the majority of open meeting attendees disagreed with the idea of mutually exclusive definitions. Their viewpoint was supported by definitions outside the health research context, the use of the terms 'pilot' and 'feasibility' in the literature, and participants at the international consensus meeting. In our framework, pilot studies are a subset of feasibility studies, rather than the two being mutually exclusive. A feasibility study asks whether something can be done, should we proceed with it, and if so, how. A pilot study asks the same questions but also has a specific design feature: in a pilot study a future study, or part of a future study, is conducted on a smaller scale. We suggest that to facilitate their identification, these studies should be clearly identified using the terms 'feasibility' or 'pilot' as appropriate. This should include feasibility studies that are largely qualitative; we found these difficult to identify in electronic searches because researchers rarely used the term 'feasibility' in the title or abstract of such studies. Investigators should also report appropriate objectives and methods related to feasibility; and give clear confirmation that their study is in preparation for a future randomised controlled trial designed to assess the effect of an intervention.

Use of concept mapping to characterize relationships among implementation strategies and assess their feasibility and importance: results from the Expert Recommendations for Implementing Change (ERIC) study.

PubMed

Waltz, Thomas J; Powell, Byron J; Matthieu, Monica M; Damschroder, Laura J; Chinman, Matthew J; Smith, Jeffrey L; Proctor, Enola K; Kirchner, JoAnn E

2015-08-07

Poor terminological consistency for core concepts in implementation science has been widely noted as an obstacle to effective meta-analyses. This inconsistency is also a barrier for those seeking guidance from the research literature when developing and planning implementation initiatives. The Expert Recommendations for Implementing Change (ERIC) study aims to address one area of terminological inconsistency: discrete implementation strategies involving one process or action used to support a practice change. The present report is on the second stage of the ERIC project that focuses on providing initial validation of the compilation of 73 implementation strategies that were identified in the first phase. Purposive sampling was used to recruit a panel of experts in implementation science and clinical practice (N = 35). These key stakeholders used concept mapping sorting and rating activities to place the 73 implementation strategies into similar groups and to rate each strategy's relative importance and feasibility. Multidimensional scaling analysis provided a quantitative representation of the relationships among the strategies, all but one of which were found to be conceptually distinct from the others. Hierarchical cluster analysis supported organizing the 73 strategies into 9 categories. The ratings data reflect those strategies identified as the most important and feasible. This study provides initial validation of the implementation strategies within the ERIC compilation as being conceptually distinct. The categorization and strategy ratings of importance and feasibility may facilitate the search for, and selection of, strategies that are best suited for implementation efforts in a particular setting.

Cost-Effects Analysis of Year-Round Education Programs.

ERIC Educational Resources Information Center

Hough, David; And Others

This feasibility study was designed to gather and analyze data to determine the potential cost-effectiveness of year-round education (YRE) compared to traditional-schedule education in California. An expanded version of the Stanford Research Institute's cost model was used to fit a broad conceptualization that enabled school districts with…

10 CFR Appendix A to Subpart D of... - Categorical Exclusions Applicable to General Agency Actions

Code of Federal Regulations, 2010 CFR

2010-01-01

... research and development A1Routine actions necessary to support the normal conduct of agency business, such... (including, but not limited to, literature surveys, inventories, audits), data analysis (including computer modelling), document preparation (such as conceptual design or feasibility studies, analytical energy supply...

10 CFR Appendix A to Subpart D of... - Categorical Exclusions Applicable to General Agency Actions

Code of Federal Regulations, 2012 CFR

2012-01-01

... agreements for energy research and development A1Routine DOE business actions Routine actions necessary to... dissemination Information gathering (including, but not limited to, literature surveys, inventories, site visits... (including, but not limited to, conceptual design, feasibility studies, and analytical energy supply and...

10 CFR Appendix A to Subpart D of... - Categorical Exclusions Applicable to General Agency Actions

Code of Federal Regulations, 2014 CFR

2014-01-01

... International agreements for energy research and development A1 Routine DOE business actions Routine actions... dissemination Information gathering (including, but not limited to, literature surveys, inventories, site visits... (including, but not limited to, conceptual design, feasibility studies, and analytical energy supply and...

10 CFR Appendix A to Subpart D of... - Categorical Exclusions Applicable to General Agency Actions

Code of Federal Regulations, 2013 CFR

2013-01-01

... agreements for energy research and development A1Routine DOE business actions Routine actions necessary to... dissemination Information gathering (including, but not limited to, literature surveys, inventories, site visits... (including, but not limited to, conceptual design, feasibility studies, and analytical energy supply and...

10 CFR Appendix A to Subpart D of... - Categorical Exclusions Applicable to General Agency Actions

Code of Federal Regulations, 2011 CFR

2011-01-01

... research and development A1Routine actions necessary to support the normal conduct of agency business, such... (including, but not limited to, literature surveys, inventories, audits), data analysis (including computer modelling), document preparation (such as conceptual design or feasibility studies, analytical energy supply...

Hard X-ray imaging facility for space shuttle: A scientific and conceptual engineering study

NASA Technical Reports Server (NTRS)

Peterson, L. E.; Hudson, H. S.; Hurford, G.; Schneible, D.

1976-01-01

A shuttle-accommodated instrument for imaging hard X-rays in the study of nonthermal particles and high temperature particles in various solar and cosmic phenomena was defined and its feasibility demonstrated. The imaging system configuration is described as well as the electronics, aspect systems, mechanical and thermal properties and the ground support equipment.

Feasiblity study for a 34 GHz (Ka band) gyroamplifier

NASA Technical Reports Server (NTRS)

Stone, D. S.; Bier, R. E.; Caplan, M.; Huey, H. E.; Pirkle, D. R.; Robinson, J. D.; Thompson, L.

1984-01-01

The feasibility of using a gyroklystron power tube as the final amplifier in a 400 kW CW 34 GHz transmitter on the Goldstone Antenna is investigated. A conceptual design of the gyroklystron and the transmission line connecting it with the antenna feed horn is presented. The performance characteristics of the tube and transmission line are compared to the transmitter requirements for a deep space radar system. Areas of technical risk for a follow-on hardware development program for the gyroklystron amplifier and overmoded transmission line components are discussed.

A feasibility study: Forest Fire Advanced System Technology (FFAST)

NASA Technical Reports Server (NTRS)

Mcleod, R. G.; Martin, T. Z.; Warren, J.

1983-01-01

The National Aeronautics and Space Administration/Jet Propulsion Laboratory and the United States Department of Agriculture Forest Service completed a feasibility study that examined the potential uses of advanced technology in forest fires mapping and detection. The current and future (1990's) information needs in forest fire management were determined through interviews. Analysis shows that integrated information gathering and processing is needed. The emerging technologies that were surveyed and identified as possible candidates for use in an end to end system include ""push broom'' sensor arrays, automatic georeferencing, satellite communication links, near real or real time image processing, and data integration. Matching the user requirements and the technologies yielded a ""strawman'' system configuration. The feasibility study recommends and outlines the implementation of the next phase for this project, a two year, conceptual design phase to define a system that warrants continued development.

Data on conceptual design of cryogenic energy storage system combined with liquefied natural gas regasification process.

PubMed

Lee, Inkyu; Park, Jinwoo; Moon, Il

2017-12-01

This paper describes data of an integrated process, cryogenic energy storage system combined with liquefied natural gas (LNG) regasification process. The data in this paper is associated with the article entitled "Conceptual Design and Exergy Analysis of Combined Cryogenic Energy Storage and LNG Regasification Processes: Cold and Power Integration" (Lee et al., 2017) [1]. The data includes the sensitivity case study dataset of the air flow rate and the heat exchanging feasibility data by composite curves. The data is expected to be helpful to the cryogenic energy process development.

MINIPILOT SOLAR SYSTEM: DESIGN/OPERATION OF SYSTEM AND RESULTS OF NON-SOLAR TESTING AT MRI

EPA Science Inventory

Prior to this project, MRI had carried out work for the Environmental Protection Agency (EPA) on the conceptual design of a solar system for solid waste disposal and a follow-on project to study the feasibility of bench-scale testing of desorption of organics from soil with destr...

Solution-Space Screening of a Hypersonic Endurance Demonstrator

NASA Technical Reports Server (NTRS)

Chudoba, Bernd; Coleman, Gary; Oza, Amit; Gonzalez, Lex; Czysz, Paul

2012-01-01

This report documents a parametric sizing study performed to develop a program strategy for research and development and procurement of a feasible next-generation hypersonic air-breathing endurance demonstrator. Overall project focus has been on complementing technical and managerial decision-making during the earliest conceptual design phase towards minimization of operational, technical, and managerial risks.

Formative Evaluation Study for AESP Diagnostic and Prescriptive Reading Course. Technical Report Number Three.

ERIC Educational Resources Information Center

Bramble, William J., Ed.; Ausness, Claudine, Ed.

The Appalachian Education Satellite Project (AESP) was conceptualized in 1973 (1) to develop courses in reading and career-education instruction for teachers in the Appalachian region, and (2) to determine the feasibility of conducting such courses over a large geographical area via communications satellites. This report describes the formative…

Conceptual Study of Rotary-Wing Microrobotics

DTIC Science & Technology

2008-03-27

tensile residual stress, respectively [78-80]. ......... 48  Table 8: Wing-T design parameters compared to Tsuzuki’s recommendations. ....... 73...Table 13: Summary of key parameters for a feasible rotary-wing MEMS robot design...Direct Methanol Fuel Cell DOF Degrees of Freedom DRIE Deep Reactive Ion Etch FEA Finite Element Analysis FEM Finite Element Modeling FOM Figure

Feasibility study of using satellites for a disaster warning system

NASA Technical Reports Server (NTRS)

1973-01-01

The development of requirements for the Disaster Warning System (DWS) was investigated in relation to the National Weather Service. Conceptual communication traffic flow patterns for the future of the NWS are studied to determine the impact of the DWS on the MWS. The planned warning systems, and satellite communications are discussed along with data collection, and communication services.

An open trial of individualized face-to-face cognitive behavior therapy for psychological distress in parents of children after end of treatment for childhood cancer including a cognitive behavioral conceptualization.

PubMed

Ljungman, Lisa; Cernvall, Martin; Ghaderi, Ata; Ljungman, Gustaf; von Essen, Louise; Ljótsson, Brjánn

2018-01-01

A subgroup of parents of children who have been treated for childhood cancer report high levels of psychological distress. To date there is no empirically supported psychological treatment targeting cancer-related psychological distress in this population. The aim of the current study was to test the feasibility and preliminarily evaluate the effect of individualized face-to-face cognitive behavior therapy (CBT) for parents of children after the end of treatment for childhood cancer. A secondary aim was to present a cognitive behavioral conceptualization of cancer-related distress for these parents. An open trial was conducted where 15 parents of children who had completed successful treatment for cancer three months to five years earlier and who reported psychological distress related to a child's previous cancer disease were provided CBT at a maximum of 15 sessions. Participants were assessed at baseline, post-intervention, and three-month follow-up using self-reported psychological distress (including posttraumatic stress symptoms (PTSS), depression, and anxiety) and the diagnostic Mini-International Neuropsychiatric Interview. Feasibility outcomes relating to recruitment, data collection, and delivery of the treatment were also examined. Individual case formulations for each participant guided the intervention and these were aggregated and presented in a conceptualization detailing core symptoms and their suggested maintenance mechanisms. A total of 93% of the participants completed the treatment and all of them completed the follow-up assessment. From baseline to post-assessment, parents reported significant improvements in PTSS, depression, and anxiety with medium to large effect sizes (Cohen's d = 0.65-0.92). Results were maintained or improved at a three-month follow-up. At baseline, seven (47%) participants fulfilled the diagnostic criteria for major depressive disorder and four (29%) fulfilled the criteria for posttraumatic stress disorder, compared to none at a post-assessment and a follow-up assessment. The resulting cognitive behavioral conceptualization suggests traumatic stress and depression as the core features of distress, and avoidance and inactivity is suggested as the core maintenance mechanisms. The treatment was feasible and acceptable to the participants. Significant improvements in distress were observed during the study. Overall, results suggest that the psychological treatment for parents of children after end of treatment for childhood cancer used in the current study is promising and should be tested and evaluated in future studies.

Cryogenic On-Orbit Liquid Depot Storage, Acquisition, and Transfer satellite (COLD-SAT) feasibility study

NASA Technical Reports Server (NTRS)

Bailey, William J.; Weiner, Stephen P.; Beekman, Douglas H.; Dennis, Mark F.; Martin, Timothy A.

1990-01-01

The Cryogenic On-Orbit Liquid Depot Storage, Acquisition, and Transfer Satellite (COLD-SAT) is an experimental spacecraft launched from an expendable launch vehicle which is designed to investigate the systems and technologies required for efficient, effective, and reliable management of cryogenic fluid in the reduced gravity space environment. The COLD-SAT program will provide the necessary data base and provide low-g proving of fluid and thermal models of cryogenic storage, transfer, and resupply concepts and processes. A conceptual approach was developed and an overview of the results of the 24 month COLD-SAT Phase A feasibility is described which includes: (1) a definition of the technology needs and the accompanying experimental 3 month baseline mission; (2) a description of the experiment subsystem, major features and rationale for satisfaction of primary and secondary experiment requirements using liquid hydrogen as the test fluid; and (3) a presentation of the conceptual design of the COLD-SAT spacecraft subsystems which support the on-orbit experiment with emphasis on areas of greatest challenge.

Healthy cooking classes at a children’s cancer hospital and patient/survivor summer camp: initial reactions and feasibility

PubMed Central

Raber, Margaret; Crawford, Karla; Chandra, Joya

2018-01-01

Objective Childhood cancer survivors (CCS) have been shown to practice sub-optimal dietary intake and may benefit from nutrition interventions during and after treatment. Cooking classes have become popular for encouraging healthy eating behaviors in community-based programming and academic research, however, literature on teaching cooking classes in CCS is limited. The purpose of this study is to address the development and implementation of classes for CCS based on a recently developed framework of healthy cooking behavior. Design A conceptual framework was developed from a systematic literature review and used to guide healthy cooking classes for CCS in different settings. Setting One pediatric cancer hospital inpatient unit, one pediatric cancer in-hospital camp program and two off-site pediatric cancer summer camp programs. Subjects One hundred and eighty nine CCS of varying ages and thirteen parents of CCS. Results Seventeen classes were taught at camps and seven classes in the hospital inpatient unit. Healthy cooking classes based on the conceptual framework are feasible and were well received by CCS. Conclusions Cooking classes for CCS, both at the hospital and at camp, reinforced the principles of the conceptual framework. Future trials should assess the dietary and anthropometric impact of evidence-based healthy cooking classes in CCS. PMID:28463101

Healthy cooking classes at a children's cancer hospital and patient/survivor summer camps: initial reactions and feasibility.

PubMed

Raber, Margaret; Crawford, Karla; Chandra, Joya

2017-06-01

Childhood cancer survivors (CCS) have been shown to practise suboptimal dietary intake and may benefit from nutrition interventions during and after treatment. Cooking classes have become popular for encouraging healthy eating behaviours in community-based programming and academic research; however, literature on teaching cooking classes in CCS is limited. The purpose of the present study was to address the development and implementation of classes for CCS based on a recently developed framework of healthy cooking behaviour. A conceptual framework was developed from a systematic literature review and used to guide healthy cooking classes for CCS in different settings. One paediatric cancer hospital inpatient unit, one paediatric cancer in-hospital camp programme and two off-site paediatric cancer summer camp programmes. One hundred and eighty-nine CCS of varying ages and thirteen parents of CCS. Seventeen classes were taught at camps and seven classes in the hospital inpatient unit. Healthy cooking classes based on the conceptual framework are feasible and were well received by CCS. Cooking classes for CCS, both at the hospital and at camp, reinforced the principles of the conceptual framework. Future trials should assess the dietary and anthropometric impact of evidence-based healthy cooking classes in CCS.

Feasibility study of a zero-gravity (orbital) atmospheric cloud physics experiments laboratory

NASA Technical Reports Server (NTRS)

Hollinden, A. B.; Eaton, L. R.

1972-01-01

A feasibility and concepts study for a zero-gravity (orbital) atmospheric cloud physics experiment laboratory is discussed. The primary objective was to define a set of cloud physics experiments which will benefit from the near zero-gravity environment of an orbiting spacecraft, identify merits of this environment relative to those of groundbased laboratory facilities, and identify conceptual approaches for the accomplishment of the experiments in an orbiting spacecraft. Solicitation, classification and review of cloud physics experiments for which the advantages of a near zero-gravity environment are evident are described. Identification of experiments for potential early flight opportunities is provided. Several significant accomplishments achieved during the course of this study are presented.

An assessment and validation study of nuclear reactors for low power space applications

NASA Technical Reports Server (NTRS)

Klein, A. C.; Gedeon, S. R.; Morey, D. C.

1987-01-01

The feasibility and safety of six conceptual small, low power nuclear reactor designs was evaluated. Feasibility evaluations included the determination of sufficient reactivity margins for seven years of full power operation and safe shutdown as well as handling during pre-launch assembly phases. Safety evaluations were concerned with the potential for maintaining subcritical conditions in the event of launch or transportation accidents. These included water immersion accident scenarios both with and without water flooding the core. Results show that most of the concepts can potentially meet the feasibility and safety requirements; however, due to the preliminary nature of the designs considered, more detailed designs will be necessary to enable these concepts to fully meet the safety requirements.

Achieving Space Shuttle ATO Using the Five-Segment Booster (FSB)

NASA Technical Reports Server (NTRS)

Sauvageau, Donald R.; McCool, Alex (Technical Monitor)

2001-01-01

As part of the continuing effort to identify approaches to improve the safety and reliability of the Space Shuttle system, a Five-Segment Booster (FSB) design was conceptualized as a replacement for the current Space Shuttle boosters. The FSB offers a simple, unique approach to improve astronaut safety and increase performance margin. To determine the feasibility of the FSB, a Phase A study effort was sponsored by NASA and directed by the Marshall Space Flight Center. This study was initiated in March of 1999 and completed in December of 2000. The basic objective of this study was to assess the feasibility of the FSB design concept and also estimate the cost and scope of a full-scale development program for the FSB. In order to ensure an effective and thorough evaluation of the FSB concept, four team members were put on contract to support various areas of importance in assessing the overall feasibility of the design approach.

The PHLAME firefighters' study: feasibility and findings.

PubMed

Elliot, Diane L; Goldberg, Linn; Duncan, Terry E; Kuehl, Kerry S; Moe, Esther L; Breger, Rosemary K R; DeFrancesco, Carol L; Ernst, Denise B; Stevens, Victor J

2004-01-01

To assess efficacy of 2 worksite health promotion interventions. Randomly assign 3 fire stations to (a) team-based curriculum, (b) individual counselor meetings, and (c) control. Both interventions were feasible and acceptable, and they resulted in significant reductions in LDL cholesterol. The team approach significantly increased coworker cohesion, personal exercise habits, and coworkers' healthy behaviors. The one-on-one strategy significantly increased dietary self-monitoring, decreased fat intake, and reduced depressed feelings. Although both interventions promoted healthy behaviors, specific outcomes differed and reflected their conceptual underpinnings. The team-based curriculum is innovative and may enlist influences not accessed with individual formats.

DEMONSTRATION OF FUEL CELLS TO RECOVER ENERGY FROM LANDFILL GAS - PHASE III. DEMONSTRATION TESTS - PHASE IV. GUIDELINES AND RECOMMENDATIONS- VOLUME 1. TECHNICAL REPORT

EPA Science Inventory

The report summarizes the results of a four-phase program to demonstrate that fuel cell energy recovery using a commercial phosphoric acid fuel cell is both environmentally sound and commercially feasible. Phase I, a conceptual design and evaluation study, addressed the technical...

DEMONSTRATION OF FUEL CELLS TO RECOVER ENERGY FROM LANDFILL GAS - PHASE III. DEMONSTRATION TESTS - PHASE IV. GUIDELINES AND DEMONSTRATIONS - VOLUME 2. APPENDICES

EPA Science Inventory

The report summarizes the results of a four-phase program to demonstrate that fuel cell energy recovery using a commercial phosphoric acid fuel cell is both environmentally sound and commercially feasible. Phase I, a conceptual design and evaluation study, addressed the technical...

Conceptualizing and Treating Social Anxiety in Autism Spectrum Disorder: A Focus Group Study with Multidisciplinary Professionals

ERIC Educational Resources Information Center

Spain, Debbie; Rumball, Freya; O'Neill, Lucy; Sin, Jacqueline; Prunty, Jonathan; Happé, Francesca

2017-01-01

Background: Individuals who have autism spectrum disorders (ASD) commonly experience social anxiety (SA). Disentangling SA symptoms from core ASD characteristics is complex, partly due to diagnostic overshadowing and co-occurring alexithymia. Causal and maintaining mechanisms for SA in ASD are underexplored, but it is feasible that there is an ASD…

Integrated Utility Systems Feasibility Study and Conceptual Design at the University of Florida. Executive Summary.

ERIC Educational Resources Information Center

Kirmse, Dale W.; Manyimo, Steve B.

This executive summary presents a brief analysis of findings and recommendations. The concept of the Integrated Utility System (IUS) is to consider the interaction and mutual support of five utility subsystems needed by a campus complex of buildings. The subsystems are: (1) Electric power service; (2) Heating - ventilating - air conditioning and…

Defining Feasibility and Pilot Studies in Preparation for Randomised Controlled Trials: Development of a Conceptual Framework

PubMed Central

Eldridge, Sandra M.; Lancaster, Gillian A.; Campbell, Michael J.; Thabane, Lehana; Hopewell, Sally; Coleman, Claire L.; Bond, Christine M.

2016-01-01

We describe a framework for defining pilot and feasibility studies focusing on studies conducted in preparation for a randomised controlled trial. To develop the framework, we undertook a Delphi survey; ran an open meeting at a trial methodology conference; conducted a review of definitions outside the health research context; consulted experts at an international consensus meeting; and reviewed 27 empirical pilot or feasibility studies. We initially adopted mutually exclusive definitions of pilot and feasibility studies. However, some Delphi survey respondents and the majority of open meeting attendees disagreed with the idea of mutually exclusive definitions. Their viewpoint was supported by definitions outside the health research context, the use of the terms ‘pilot’ and ‘feasibility’ in the literature, and participants at the international consensus meeting. In our framework, pilot studies are a subset of feasibility studies, rather than the two being mutually exclusive. A feasibility study asks whether something can be done, should we proceed with it, and if so, how. A pilot study asks the same questions but also has a specific design feature: in a pilot study a future study, or part of a future study, is conducted on a smaller scale. We suggest that to facilitate their identification, these studies should be clearly identified using the terms ‘feasibility’ or ‘pilot’ as appropriate. This should include feasibility studies that are largely qualitative; we found these difficult to identify in electronic searches because researchers rarely used the term ‘feasibility’ in the title or abstract of such studies. Investigators should also report appropriate objectives and methods related to feasibility; and give clear confirmation that their study is in preparation for a future randomised controlled trial designed to assess the effect of an intervention. PMID:26978655

Conceptual design and feasibility evaluation model of a 10 to the 8th power bit oligatomic mass memory. Volume 3: Operation manual

NASA Technical Reports Server (NTRS)

Horst, R. L.; Nordstrom, M. J.

1972-01-01

An operation manual is presented for the oligatomic mass memory feasibility model. It includes a brief description of the memory and exerciser units, a description of the controls and their functions, the operating procedures, the test points and adjustments, and the circuit diagram.

FBI fingerprint identification automation study. AIDS 3 evaluation report. Volume 3: Operational feasibility

NASA Technical Reports Server (NTRS)

Mulhall, B. D. L.

1980-01-01

An evaluation is presented which is defined as the adequacy of system design with known functional and performance requirements. The proposed Rockwell International AIDS 3 card, document and data flow are presented to summarize the concepts involved and the relationships between functions. The analysis and evaluation includes a study of system capability, processing rates, search requirements and response accuracy as well as a consideration of operational components and hardware integration. Results indicate that the AIDS 3 System concept is operationally feasible if production capacity is slightly enhanced but that operational complexity, hardware integration and a lack of conceptual data pertinent to some of the functions are areas of concern.

Feasibility of dynamic models of the interaction of potential oil spills with bowhead and gray whales in the Bering, Chukchi, and Beaufort Seas

DOE Office of Scientific and Technical Information (OSTI.GOV)

Reed, M.; Bowles, A.E.; Anderson, E.L.

1984-08-01

Feasibility and design considerations for developing computer models of migratory bow-head and gray whales and linking such models to oil spill models for application in Alaskan Outer Continental Shelf areas were evaluated. A summary of all relevant bowhead and gray whale distributional and migration data were summarized and presented at monthly intervals. The data were, for the most part, deemed sufficient to prepare whale migration simulation models. A variety of whale migration conceptual models were devised and ranking was achieved by means of a scaling-weighted protocol. Existing oil spill trajectory and fate models, as well as conceptual models, were similarlymore » ranked.« less

BUILDING MATERIALS RECLAMATION PROGRAM

DOE Office of Scientific and Technical Information (OSTI.GOV)

David C. Weggel; Shen-En Chen; Helene Hilger

2010-08-31

This report describes work conducted on the Building Materials Reclamation Program for the period of September 2008 to August 2010. The goals of the project included selecting materials from the local construction and demolition (C&D) waste stream and developing economically viable reprocessing, reuse or recycling schemes to divert them from landfill storage. Educational resources as well as conceptual designs and engineering feasibility demonstrations were provided for various aspects of the work. The project was divided into two distinct phases: Research and Engineering Feasibility and Dissemination. In the Research Phase, a literature review was initiated and data collection commenced, an advisorymore » panel was organized, and research was conducted to evaluate high volume C&D materials for nontraditional use; five materials were selected for more detailed investigations. In the Engineering Feasibility and Dissemination Phase, a conceptual study for a regional (Mecklenburg and surrounding counties) collection and sorting facility was performed, an engineering feasibility project to demonstrate the viability of recycling or reuse schemes was created, the literature review was extended and completed, and pedagogical materials were developed. Over the two-year duration of the project, all of the tasks and subtasks outlined in the original project proposal have been completed. The Final Progress Report, which briefly describes actual project accomplishments versus the tasks/subtasks of the original project proposal, is included in Appendix A of this report. This report describes the scientific/technical aspects (hypotheses, research/testing, and findings) of six subprojects that investigated five common C&D materials. Table 1 summarizes the six subprojects, including the C&D material studied and the graduate student and the faculty advisor on each subproject.« less

Conceptual Design, Feasibility and Payoff Analysis of a Third Stage for EELV

DTIC Science & Technology

2014-06-01

the overall vehicle architecture, identifying locations for modification or stage shape. Trade studies of various propellant types (LOX/ LH2 , LOX/RP...or stage shape. Trade studies of various propellant types (LOX/ LH2 , LOX/RP, LOX/methane, hydrazine monopropellant) were included in the analysis...Geostationary transfer orbit Isp = Specific impulse LEO = Low Earth Orbit LOX = Liquid oxygen LH2 = Liquid hydrogen POST = Program to

Electric power generation using geothermal brine resources for a proof of concept facility

NASA Technical Reports Server (NTRS)

Hankin, J. W.

1974-01-01

An exploratory systems study of a geothermal proof-of-concept facility is being conducted. This study is the initial phase (Phase 0) of a project to establish the technical and economic feasibility of using hot brine resources for electric power production and other industrial applications. Phase 0 includes the conceptual design of an experimental test-bed facility and a 10-MWe power generating facility.

X-43D Conceptual Design and Feasibility Study

NASA Technical Reports Server (NTRS)

Johnson, Donald B.; Robinson, Jeffrey S.

2005-01-01

NASA s Next Generation Launch Technology (NGLT) Program, in conjunction with the office of the Director of Defense Research and Engineering (DDR&E), developed an integrated hypersonic technology demonstration roadmap. This roadmap is an integral part of the National Aerospace Initiative (NAI), a multi-year, multi-agency cooperative effort to invest in and develop, among other things, hypersonic technologies. This roadmap contains key ground and flight demonstrations required along the path to developing a reusable hypersonic space access system. One of the key flight demonstrations required for systems that will operate in the high Mach number regime is the X-43D. As currently conceived, the X-43D is a Mach 15 flight test vehicle that incorporates a hydrogen-fueled scramjet engine. The purpose of the X-43D is to gather high Mach number flight environment and engine operability information which is difficult, if not impossible, to gather on the ground. During 2003, the NGLT Future Hypersonic Flight Demonstration Office initiated a feasibility study on the X-43D. The objective of the study was to develop a baseline conceptual design, assess its performance, and identify the key technical issues. The study also produced a baseline program plan, schedule, and cost, along with a list of key programmatic risks.

A Tuning-AHELO Conceptual Framework of Expected Desired/Learning Outcomes in Engineering. OECD Education Working Papers, Number 60

ERIC Educational Resources Information Center

OECD Publishing (NJ1), 2011

2011-01-01

The OECD Secretariat, at the invitation of the AHELO Group of National Experts, contracted the Tuning Association to undertake initial development work on learning outcomes to be used for valid and reliable assessments of students from diverse institutions and countries. The two disciplines selected for the AEHLO Feasibility Study are engineering…

Organization Domain Modeling. Volume 1. Conceptual Foundations, Process and Workproduct Description

DTIC Science & Technology

1993-07-31

J.A. Hess, W.E. Novak, and A.S. Peterson. Feature-Oriented Domain Analysis ( FODA ) Feasibility Study. Technical Report CMU/SEI-90-TR-21, Software...domain analysis (DA) and modeling, including a structured set of workproducts, a tailorable process model and a set of modeling techniques and guidelines...23 5.3.1 U sability Analysis (Rescoping) ..................................................... 24

Exploiting salient semantic analysis for information retrieval

NASA Astrophysics Data System (ADS)

Luo, Jing; Meng, Bo; Quan, Changqin; Tu, Xinhui

2016-11-01

Recently, many Wikipedia-based methods have been proposed to improve the performance of different natural language processing (NLP) tasks, such as semantic relatedness computation, text classification and information retrieval. Among these methods, salient semantic analysis (SSA) has been proven to be an effective way to generate conceptual representation for words or documents. However, its feasibility and effectiveness in information retrieval is mostly unknown. In this paper, we study how to efficiently use SSA to improve the information retrieval performance, and propose a SSA-based retrieval method under the language model framework. First, SSA model is adopted to build conceptual representations for documents and queries. Then, these conceptual representations and the bag-of-words (BOW) representations can be used in combination to estimate the language models of queries and documents. The proposed method is evaluated on several standard text retrieval conference (TREC) collections. Experiment results on standard TREC collections show the proposed models consistently outperform the existing Wikipedia-based retrieval methods.

A needs analysis method for land-use planning of illegal dumping sites: a case study in Aomori-Iwate, Japan.

PubMed

Ishii, Kazuei; Furuichi, Toru; Nagao, Yukari

2013-02-01

Land use at contaminated sites, following remediation, is often needed for regional redevelopment. However, there exist few methods of developing economically and socially feasible land-use plans based on regional needs because of the wide variety of land-use requirements. This study proposes a new needs analysis method for the conceptual land-use planning of contaminated sites and illustrates this method with a case study of an illegal dumping site for hazardous waste. In this method, planning factors consisting of the land-use attributes and related facilities are extracted from the potential needs of the residents through a preliminary questionnaire. Using the extracted attributes of land use and the related facilities, land-use cases are designed for selection-based conjoint analysis. A second questionnaire for respondents to the first one who indicated an interest in participating in the second questionnaire is conducted for the conjoint analysis to determine the utility function and marginal cost of each attribute in order to prioritize the planning factors to develop a quantitative and economically and socially feasible land-use plan. Based on the results, site-specific land-use alternatives are developed and evaluated by the utility function obtained from the conjoint analysis. In this case study of an illegal dumping site for hazardous waste, the uses preferred as part of a conceptual land-use plan following remediation of the site were (1) agricultural land and a biogas plant designed to recover energy from biomass or (2) a park with a welfare facility and an athletic field. Our needs analysis method with conjoint analysis is applicable to the development of conceptual land-use planning for similar sites following remediation, particularly when added value is considered. Copyright © 2012 Elsevier Ltd. All rights reserved.

An open trial of individualized face-to-face cognitive behavior therapy for psychological distress in parents of children after end of treatment for childhood cancer including a cognitive behavioral conceptualization

PubMed Central

Ghaderi, Ata; Ljungman, Gustaf; von Essen, Louise; Ljótsson, Brjánn

2018-01-01

Objective A subgroup of parents of children who have been treated for childhood cancer report high levels of psychological distress. To date there is no empirically supported psychological treatment targeting cancer-related psychological distress in this population. The aim of the current study was to test the feasibility and preliminarily evaluate the effect of individualized face-to-face cognitive behavior therapy (CBT) for parents of children after the end of treatment for childhood cancer. A secondary aim was to present a cognitive behavioral conceptualization of cancer-related distress for these parents. Methods An open trial was conducted where 15 parents of children who had completed successful treatment for cancer three months to five years earlier and who reported psychological distress related to a child’s previous cancer disease were provided CBT at a maximum of 15 sessions. Participants were assessed at baseline, post-intervention, and three-month follow-up using self-reported psychological distress (including posttraumatic stress symptoms (PTSS), depression, and anxiety) and the diagnostic Mini-International Neuropsychiatric Interview. Feasibility outcomes relating to recruitment, data collection, and delivery of the treatment were also examined. Individual case formulations for each participant guided the intervention and these were aggregated and presented in a conceptualization detailing core symptoms and their suggested maintenance mechanisms. Results A total of 93% of the participants completed the treatment and all of them completed the follow-up assessment. From baseline to post-assessment, parents reported significant improvements in PTSS, depression, and anxiety with medium to large effect sizes (Cohen’s d = 0.65–0.92). Results were maintained or improved at a three-month follow-up. At baseline, seven (47%) participants fulfilled the diagnostic criteria for major depressive disorder and four (29%) fulfilled the criteria for posttraumatic stress disorder, compared to none at a post-assessment and a follow-up assessment. The resulting cognitive behavioral conceptualization suggests traumatic stress and depression as the core features of distress, and avoidance and inactivity is suggested as the core maintenance mechanisms. Conclusion The treatment was feasible and acceptable to the participants. Significant improvements in distress were observed during the study. Overall, results suggest that the psychological treatment for parents of children after end of treatment for childhood cancer used in the current study is promising and should be tested and evaluated in future studies. PMID:29666751

Cryogenic On-Orbit Liquid Depot-Storage, Acquisition and Transfer (COLD-SAT) Experiment Conceptual Design and Feasibility Study

NASA Technical Reports Server (NTRS)

Kramer, Edward (Editor)

1998-01-01

The cryogenic fluid management technologies required for the exploration of the solar system can only be fully developed via space-based experiments. A dedicated spacecraft is the most efficient way to perform these experiments. This report documents the extended conceptual design of the COLD-SAT spacecraft, capable of meeting these experimental requirements. All elements, including the spacecraft, ground segment, launch site modifications and launch vehicle operations, and flight operations are included. Greatly expanded coverage is provided for those areas unique to this cryogenic spacecraft, such as the experiment system, attitude control system, and spacecraft operations. Supporting analyses are included as are testing requirements, facilities surveys, and proposed project timelines.

Feasibility of flywheel energy storage systems for applications in future space missions

NASA Technical Reports Server (NTRS)

Santo, G. Espiritu; Gill, S. P.; Kotas, J. F.; Paschall, R.

1995-01-01

The objective of this study was to examine the overall feasibility of deploying electromechanical flywheel systems in space used for excess energy storage. Results of previous Rocketdyne studies have shown that the flywheel concept has a number of advantages over the NiH2 battery, including higher specific energy, longer life and high roundtrip efficiency. Based on this prior work, this current study was broken into four subtasks. The first subtask investigated the feasibility of replacing the NiH2 battery orbital replacement unit (ORU) on the international space station (ISSA) with a flywheel ORU. In addition, a conceptual design of a generic flywheel demonstrator experiment implemented on the ISSA was completed. An assessment of the life cycle cost benefits of replacing the station battery energy storage ORU's with flywheel ORU's was performed. A fourth task generated a top-level development plan for critical flywheel technologies, the flywheel demonstrator experiments and its evolution into the production unit flywheel replacement ORU.

Advanced Space Suit Insulation Feasibility Study

NASA Technical Reports Server (NTRS)

Trevino, Luis A.; Orndoff, Evelyne S.

2000-01-01

For planetary applications, the space suit insulation has unique requirements because it must perform in a dynamic mode to protect humans in the harsh dust, pressure and temperature environments. Since the presence of a gaseous planetary atmosphere adds significant thermal conductance to the suit insulation, the current multi-layer flexible insulation designed for vacuum applications is not suitable in reduced pressure planetary environments such as that of Mars. Therefore a feasibility study has been conducted at NASA to identify the most promising insulation concepts that can be developed to provide an acceptable suit insulation. Insulation concepts surveyed include foams, microspheres, microfibers, and vacuum jackets. The feasibility study includes a literature survey of potential concepts, an evaluation of test results for initial insulation concepts, and a development philosophy to be pursued as a result of the initial testing and conceptual surveys. The recommended focus is on microfibers due to the versatility of fiber structure configurations, the wide choice of fiber materials available, the maturity of the fiber processing industry, and past experience with fibers in insulation applications

Conceptual design of the MHD Engineering Test Facility

NASA Technical Reports Server (NTRS)

Bents, D. J.; Bercaw, R. W.; Burkhart, J. A.; Mroz, T. S.; Rigo, H. S.; Pearson, C. V.; Warinner, D. K.; Hatch, A. M.; Borden, M.; Giza, D. A.

1981-01-01

The reference conceptual design of the MHD engineering test facility, a prototype 200 MWe coal-fired electric generating plant designed to demonstrate the commerical feasibility of open cycle MHD is summarized. Main elements of the design are identified and explained, and the rationale behind them is reviewed. Major systems and plant facilities are listed and discussed. Construction cost and schedule estimates are included and the engineering issues that should be reexamined are identified.

EVALUATION GUIDELINES FOR ECOLOGICAL INDICATORS

EPA Science Inventory

This document presents fifteen technical guidelines to evaluate the suitability of an ecological indicator for a particular monitoring program. The guidelines are organized within four evaluation phrases: conceptual relevance, feasibility of implementation, response variability...

Enabling Rapid Naval Architecture Design Space Exploration

NASA Technical Reports Server (NTRS)

Mueller, Michael A.; Dufresne, Stephane; Balestrini-Robinson, Santiago; Mavris, Dimitri

2011-01-01

Well accepted conceptual ship design tools can be used to explore a design space, but more precise results can be found using detailed models in full-feature computer aided design programs. However, defining a detailed model can be a time intensive task and hence there is an incentive for time sensitive projects to use conceptual design tools to explore the design space. In this project, the combination of advanced aerospace systems design methods and an accepted conceptual design tool facilitates the creation of a tool that enables the user to not only visualize ship geometry but also determine design feasibility and estimate the performance of a design.

Quantum Physics Principles and Communication in the Acute Healthcare Setting: A Pilot Study.

PubMed

Helgeson, Heidi L; Peyerl, Colleen Kraft; Solheim-Witt, Marit

This pilot study explores whether clinician awareness of quantum physics principles could facilitate open communication between patients and providers. In the spirit of action research, this study was conceptualized with a holistic view of human health, using a mixed method design of grounded theory as an emergent method. Instrumentation includes surveys and a focus group discussion with twelve registered nurses working in an acute care hospital setting. Findings document that the preliminary core phenomenon, energy as information, influences communication in the healthcare environment. Key emergent themes include awareness, language, validation, open communication, strategies, coherence, incoherence and power. Research participants indicate that quantum physics principles provide a language and conceptual framework for improving their awareness of communication and interactions in the healthcare environment. Implications of this pilot study support the feasibility of future research and education on awareness of quantum physics principles in other clinical settings. Copyright © 2016 Elsevier Inc. All rights reserved.

A Dual-Beam Irradiation Facility for a Novel Hybrid Cancer Therapy

NASA Astrophysics Data System (ADS)

Sabchevski, Svilen Petrov; Idehara, Toshitaka; Ishiyama, Shintaro; Miyoshi, Norio; Tatsukawa, Toshiaki

2013-01-01

In this paper we present the main ideas and discuss both the feasibility and the conceptual design of a novel hybrid technique and equipment for an experimental cancer therapy based on the simultaneous and/or sequential application of two beams, namely a beam of neutrons and a CW (continuous wave) or intermittent sub-terahertz wave beam produced by a gyrotron for treatment of cancerous tumors. The main simulation tools for the development of the computer aided design (CAD) of the prospective experimental facility for clinical trials and study of such new medical technology are briefly reviewed. Some tasks for a further continuation of this feasibility analysis are formulated as well.

Feasibility of commercial space manufacturing, production of pharmaceuticals. Volume 2: Technical analysis

NASA Technical Reports Server (NTRS)

1978-01-01

A technical analysis on the feasibility of commercial manufacturing of pharmaceuticals in space is presented. The method of obtaining pharmaceutical company involvement, laboratory results of the separation of serum proteins by the continuous flow electrophoresis process, the selection and study of candidate products, and their production requirements is described. The candidate products are antihemophilic factor, beta cells, erythropoietin, epidermal growth factor, alpha-1-antitrypsin and interferon. Production mass balances for antihemophelic factor, beta cells, and erythropoietin were compared for space versus ground operation. A conceptual description of a multiproduct processing system for space operation is discussed. Production requirements for epidermal growth factor of alpha-1-antitrypsin and interferon are presented.

The initial conceptualization and design of a meteorological satellite

NASA Technical Reports Server (NTRS)

Greenfield, S. M.

1982-01-01

The meteorological satellite had its substantive origin in the analytical process that helped initiate America's military satellite program. Its impetus lay in the desire to acquire current meteorological information in large areas for which normal meteorological observational data were not available on a day-to-day basis. Serious consideration was given to the feasibility of reconnaissance from meteorological satellites. The conceptualization of a meteorological satellite is discussed along with the early research which gave substance to that concept.

Solar Electric and Chemical Propulsion Technology Applications to a Titan Orbiter/Lander Mission

NASA Technical Reports Server (NTRS)

Cupples, Michael

2007-01-01

Several advanced propulsion technology options were assessed for a conceptual Titan Orbiter/Lander mission. For convenience of presentation, the mission was broken into two phases: interplanetary and Titan capture. The interplanetary phase of the mission was evaluated for an advanced Solar Electric Propulsion System (SEPS), while the Titan capture phase was evaluated for state-of-art chemical propulsion (NTO/Hydrazine), three advanced chemical propulsion options (LOX/Hydrazine, Fluorine/Hydrazine, high Isp mono-propellant), and advanced tank technologies. Hence, this study was referred to as a SEPS/Chemical based option. The SEPS/Chemical study results were briefly compared to a 2002 NASA study that included two general propulsion options for the same conceptual mission: an all propulsive based mission and a SEPS/Aerocapture based mission. The SEP/Chemical study assumed identical science payload as the 2002 NASA study science payload. The SEPS/Chemical study results indicated that the Titan mission was feasible for a medium launch vehicle, an interplanetary transfer time of approximately 8 years, an advanced SEPS (30 kW), and current chemical engine technology (yet with advanced tanks) for the Titan capture. The 2002 NASA study showed the feasibility of the mission based on a somewhat smaller medium launch vehicle, an interplanetary transfer time of approximately 5.9 years, an advanced SEPS (24 kW), and advanced Aerocapture based propulsion technology for the Titan capture. Further comparisons and study results were presented for the advanced chemical and advanced tank technologies.

Unit Under Test Simulator Feasibility Study.

DTIC Science & Technology

1980-06-01

interlocking connectors to conceptual differences such as octopus types of cables. 0 The validity of the IA description to the UUT simulator. Although...Research Institute, January 1978. 146. Ring , S. J. "Automatic Testing Via a Distributed Intelligence Processing System." Autotestcon 77, 2-4 November 1977...pp. 89-98. 147. Ring , S. J. "A Distributed Intelligence Automatic Test System for PATRIOT." IEEE Trans. 1977, Aerosp. and Electron Systems, Vol. AES

An investigation and conceptual design of a holographic starfield and landmark tracker

NASA Technical Reports Server (NTRS)

Welch, J. D.

1973-01-01

The analysis, experiments, and design effort of this study have supported the feasibility of the basic holographic tracker concept. Image intensifiers and photoplastic recording materials were examined, along with a Polaroid rapid process silver halide material. Two reference beam, coherent optical matched filter technique was used for multiplexing spatial frequency filters for starfields. A 1 watt HeNe laser and an electro-optical readout are also considered.

A conceptual design and operational characteristics for a Mars rover for a 1979 or 1981 Viking science mission

NASA Technical Reports Server (NTRS)

Darnell, W. L.; Wessel, V. W.

1974-01-01

The feasibility of a small Mars rover for use on a 1979 or 1981 Viking mission was studied and a preliminary design concept was developed. Three variations of the concept were developed to provide comparisons in mobility and science capability of the rover. Final masses of the three rover designs were approximately 35 kg, 40 kg, and 69 kg. The smallest rover is umbilically connected to the lander for power and communications purposes whereas the larger two rovers have secondary battery power and a 2-way very high frequency communication link to the lander. The capability for carrying Viking rovers (including development system) to the surface of Mars was considered first. It was found to be feasible to carry rovers of over 100 kg. Virtually all rover systems were then studied briefly to determine a feasible system concept and a practical interface with the comparable system of a 1979 or 1981 lander vehicle.

Feasibility of Traveling Wave Direct Energy Conversion of Fission Reaction Fragments

NASA Technical Reports Server (NTRS)

Tarditi, A. G.; George, J. A.; Miley, G. H.; Scott, J. H.

2013-01-01

Fission fragment direct energy conversion has been considered in the past for the purpose of increasing nuclear power plant efficiency and for advanced space propulsion. Since the fragments carry electric charge (typically in the order of 20 e) and have 100 MeV-range kinetic energy, techniques utilizing very high-voltage DC electrodes have been considered. This study is focused on a different approach: the kinetic energy of the charged fission fragments is converted into alternating current by means of a traveling wave coupling scheme (Traveling Wave Direct Energy Converter, TWDEC), thereby not requiring the utilization of high voltage technology. A preliminary feasibility analysis of the concept is introduced based on a conceptual level study and on a particle simulation model of the beam dynamics.

A preliminary study of solar powdered aircraft and associated power trains

NASA Technical Reports Server (NTRS)

Hall, D. W.; Fortenbach, C. D.; Dimiceli, E. V.; Parks, R. W.

1983-01-01

The feasibility of regeneratively powered solar high altitude powered platform (HAPP) remotely piloted vehicles was assessed. Those technologies which must be pursued to make long duration solar HAPPs feasible are recommended. A methodology which involved characterization and parametric analysis of roughly two dozen variables to determine vehicles capable of fulfilling the primary mission are defined. One of these vehicles was then conceptually designed. Variations of each major design parameter were investigated along with state-of-the-art changes in power train component capabilities. The midlatitude mission studied would be attainable by a solar HAPP if fuel cell, electrolyzer and photovoltaic technologies are pursued. Vehicles will be very large and have very lightweight structures in order to attain the combinations of altitude and duration required by the primary mission.

Maglev System Concept Definition (SCD) System Safety Review

DOT National Transportation Integrated Search

1993-01-07

As part of the National Maglev Initiative (NMI), the Federal Railroad : Administration (FRA) solicited proposals to conceptually define the technical feasibility, : performance and costs of constructing and operating Maglev systems in the United : St...

Overview of the 1986 free-piston Stirling SP-100 activities at the NASA Lewis Research Center

NASA Technical Reports Server (NTRS)

Slaby, J. G.

1986-01-01

An overview of the NASA Lewis Research Center SP-100 free-piston Stirling engine activities is presented. These activities include a free-piston Stirling space-power technology feasibility demonstration project as part of the SP-100 program being conducted in support of the Department of Defennse (DOD), Department of Energy (DOE), and NASA. The space-power Stirling advanced technology effort, under SP-100, addresses the status of the 25 kWe Space Power Demonstrator Engine (SPDE) including test results. Future space-power projections are presented along with a description of a study that will investigate the feasibility of scaling a single-cylinder free-piston Stirling space-power module to the 150 kW power range. Design parameters and conceptual design features will be presented for a 25 kWe, single-cylinder free-piston Stirling space-power converter. A description of a hydrodynamic gas bearing concept is presented whereby the displacer of a 1 kWe free-piston Stirling engine is modified to demonstrate the bearing concept. And finally the goals of a conceptual design for a 25 kWe Solar Advanced Stirling Conversion System capable of delivering electric power to an electric utility grid are discussed.

Overview of the 1986 free-piston Stirling SP-100 activities at the NASA Lewis Research Center

NASA Technical Reports Server (NTRS)

Slaby, J. G.

1986-01-01

An overview of the NASA Lewis Research Center SP-100 free-piston Stirling engine activities is presented. These activities include a free-piston Stirling space-power technology feasibility demonstration project as part of the SP-100 program being conducted in support of the Department of Defense (DOD), Department of Energy (DOE), and NASA. The space-power Stirling advanced technology effort, under SP-100, addresses the status of the 25 kWe Space Power Demonstrator Engine (SPDE) including test results. Future space-power projections are presented along with a description of a study that will investigate the feasibility of scaling a single-cylinder free-piston Stirling space-power module to the 150 kW power range. Design parameters and conceptual design features will be presented for a 25 kWe, single-cylinder free-piston Stirling space-power converter. A description of a hydrodynamic gas bearing concept is presented whereby the displacer of a 1 kWe free-piston Stirling engine is modified to demonstrate the bearing concept. And finally the goals of a conceptual design for a 25 kWe Solar Advanced Stirling Conversion System capable of delivering electric power to an electric utility grid are discussed.

Assuring consumer safety without animal testing: a feasibility case study for skin sensitisation.

PubMed

Maxwell, Gavin; Aleksic, Maja; Aptula, Aynur; Carmichael, Paul; Fentem, Julia; Gilmour, Nicola; Mackay, Cameron; Pease, Camilla; Pendlington, Ruth; Reynolds, Fiona; Scott, Daniel; Warner, Guy; Westmoreland, Carl

2008-11-01

Allergic Contact Dermatitis (ACD; chemical-induced skin sensitisation) represents a key consumer safety endpoint for the cosmetics industry. At present, animal tests (predominantly the mouse Local Lymph Node Assay) are used to generate skin sensitisation hazard data for use in consumer safety risk assessments. An animal testing ban on chemicals to be used in cosmetics will come into effect in the European Union (EU) from March 2009. This animal testing ban is also linked to an EU marketing ban on products containing any ingredients that have been subsequently tested in animals, from March 2009 or March 2013, depending on the toxicological endpoint of concern. Consequently, the testing of cosmetic ingredients in animals for their potential to induce skin sensitisation will be subject to an EU marketing ban, from March 2013 onwards. Our conceptual framework and strategy to deliver a non-animal approach to consumer safety risk assessment can be summarised as an evaluation of new technologies (e.g. 'omics', informatics), leading to the development of new non-animal (in silico and in vitro) predictive models for the generation and interpretation of new forms of hazard characterisation data, followed by the development of new risk assessment approaches to integrate these new forms of data and information in the context of human exposure. Following the principles of the conceptual framework, we have been investigating existing and developing new technologies, models and approaches, in order to explore the feasibility of delivering consumer safety risk assessment decisions in the absence of new animal data. We present here our progress in implementing this conceptual framework, with the skin sensitisation endpoint used as a case study. 2008 FRAME.

Magnetohydrodynamics (MHD) Engineering Test Facility (ETF) 200 MWe power plant Conceptual Design Engineering Report (CDER)

NASA Technical Reports Server (NTRS)

1981-01-01

The reference conceptual design of the magnetohydrodynamic (MHD) Engineering Test Facility (ETF), a prototype 200 MWe coal-fired electric generating plant designed to demonstrate the commercial feasibility of open cycle MHD, is summarized. Main elements of the design, systems, and plant facilities are illustrated. System design descriptions are included for closed cycle cooling water, industrial gas systems, fuel oil, boiler flue gas, coal management, seed management, slag management, plant industrial waste, fire service water, oxidant supply, MHD power ventilating

Magnetohydrodynamics (MHD) Engineering Test Facility (ETF) 200 MWe power plant Conceptual Design Engineering Report (CDER)

NASA Astrophysics Data System (ADS)

1981-09-01

The reference conceptual design of the magnetohydrodynamic (MHD) Engineering Test Facility (ETF), a prototype 200 MWe coal-fired electric generating plant designed to demonstrate the commercial feasibility of open cycle MHD, is summarized. Main elements of the design, systems, and plant facilities are illustrated. System design descriptions are included for closed cycle cooling water, industrial gas systems, fuel oil, boiler flue gas, coal management, seed management, slag management, plant industrial waste, fire service water, oxidant supply, MHD power ventilating

Mapping photopolarimeter spectrometer instrument feasibility study for future planetary flight missions

NASA Technical Reports Server (NTRS)

1990-01-01

Evaluations are summarized directed towards defining optimal instrumentation for performing planetary polarization measurements from a spacecraft platform. An overview of the science rationale for polarimetric measurements is given to point out the importance of such measurements for future studies and exploration of the outer planets. The key instrument features required to perform the needed measurements are discussed and applied to the requirements for the Cassini mission to Saturn. The resultant conceptual design of a spectro-polarimeter photometer for Cassini is described in detail.

Participatory design of an integrated information system design to support public health nurses and nurse managers.

PubMed

Reeder, Blaine; Hills, Rebecca A; Turner, Anne M; Demiris, George

2014-01-01

The objectives of the study were to use persona-driven and scenario-based design methods to create a conceptual information system design to support public health nursing. We enrolled 19 participants from two local health departments to conduct an information needs assessment, create a conceptual design, and conduct a preliminary design validation. Interviews and thematic analysis were used to characterize information needs and solicit design recommendations from participants. Personas were constructed from participant background information, and scenario-based design was used to create a conceptual information system design. Two focus groups were conducted as a first iteration validation of information needs, personas, and scenarios. Eighty-nine information needs were identified. Two personas and 89 scenarios were created. Public health nurses and nurse managers confirmed the accuracy of information needs, personas, scenarios, and the perceived usefulness of proposed features of the conceptual design. Design artifacts were modified based on focus group results. Persona-driven design and scenario-based design are feasible methods to design for common work activities in different local health departments. Public health nurses and nurse managers should be engaged in the design of systems that support their work. © 2013 Wiley Periodicals, Inc.

Participatory Design of an Integrated Information System Design to Support Public Health Nurses and Nurse Managers

PubMed Central

Reeder, Blaine; Hills, Rebecca A.; Turner, Anne M.; Demiris, George

2014-01-01

Objectives The objectives of the study were to use persona-driven and scenario-based design methods to create a conceptual information system design to support public health nursing. Design and Sample We enrolled 19 participants from two local health departments to conduct an information needs assessment, create a conceptual design, and conduct a preliminary design validation. Measures Interviews and thematic analysis were used to characterize information needs and solicit design recommendations from participants. Personas were constructed from participant background information, and scenario-based design was used to create a conceptual information system design. Two focus groups were conducted as a first iteration validation of information needs, personas, and scenarios. Results Eighty-nine information needs were identified. Two personas and 89 scenarios were created. Public health nurses and nurse managers confirmed the accuracy of information needs, personas, scenarios, and the perceived usefulness of proposed features of the conceptual design. Design artifacts were modified based on focus group results. Conclusion Persona-driven design and scenario-based design are feasible methods to design for common work activities in different local health departments. Public health nurses and nurse managers should be engaged in the design of systems that support their work. PMID:24117760

STARS Conceptual Framework for Reuse Processes (CFRP). Volume 2: application Version 1.0

DTIC Science & Technology

1993-09-30

Analysis and Design DISA/CIM process x OProcess [DIS93] Feature-Oriented Domain SEI process x Analysis ( FODA ) [KCH+90] JIAWG Object-Oriented Domain JIAWG...Domain Analysis ( FODA ) Feasibility Study. Technical Report CMU/S[1 ,N. I R 21. Soft- ware Engineering Institute, Carnegie Mellon University, Pittsburgh...Electronic Systems Center Air Force Materiel Command, USAF Hanscom AFB, MA 01731-5000 Prepared by: The Boeing Company , IBM, Unisys Corporation, Defense

Data Warehouse Design from HL7 Clinical Document Architecture Schema.

PubMed

Pecoraro, Fabrizio; Luzi, Daniela; Ricci, Fabrizio L

2015-01-01

This paper proposes a semi-automatic approach to extract clinical information structured in a HL7 Clinical Document Architecture (CDA) and transform it in a data warehouse dimensional model schema. It is based on a conceptual framework published in a previous work that maps the dimensional model primitives with CDA elements. Its feasibility is demonstrated providing a case study based on the analysis of vital signs gathered during laboratory tests.

Droplet burning at zero G

NASA Technical Reports Server (NTRS)

Williams, F. A.

1978-01-01

Questions of the importance and feasibility of performing experiments on droplet burning at zero gravity in Spacelab were studied. Information on the physics and chemistry of droplet combustion, with attention directed specifically to the chemical kinetics, heat and mass transfer, and fluid mechanics of the phenomena involved, are presented. The work was divided into three phases, the justification, the feasibility, and the conceptual development of a preliminary design. Results from the experiments performed revealed a few new facts concerning droplet burning, notably burning rates in excess of theoretical prediction and a phenomenon of flash extinction, both likely traceable to accumulation of carbon produced by gas-phase pyrolysis in the fuel-rich zone enclosed by the reaction surface. These experiments also showed that they were primarily due to timing difficulties.

Design investigation of solar-powered lasers for space applications

NASA Technical Reports Server (NTRS)

1982-01-01

The feasibility of using solar powered continuous wave (CW) lasers for space power transmission was investigated. Competing conceptual designs are considered. Optical pumping is summarized. Solar pumped Lasant type lasers are outlined. Indirect solar pumped lasers are considered.

Conceptualizing and Treating Social Anxiety in Autism Spectrum Disorder: A Focus Group Study with Multidisciplinary Professionals.

PubMed

Spain, Debbie; Rumball, Freya; O'Neill, Lucy; Sin, Jacqueline; Prunty, Jonathan; Happé, Francesca

2017-12-01

Individuals who have autism spectrum disorders (ASD) commonly experience social anxiety (SA). Disentangling SA symptoms from core ASD characteristics is complex, partly due to diagnostic overshadowing and co-occurring alexithymia. Causal and maintaining mechanisms for SA in ASD are underexplored, but it is feasible that there is an ASD specificity to the clinical presentation, with implications for the development of targeted treatments. Five focus groups were conducted with multidisciplinary professionals to investigate their perspectives about, and approaches to, working with individuals with ASD and SA. Data were analysed thematically. Data analysis revealed two overarching themes: conceptualizing SA in ASD and service provision. Our results suggest that adaptations to service provision are pertinent, so as to accommodate inherent impairments that can mediate assessment and intervention. Future studies should establish how aspects of the care pathway can be improved for individuals with ASD and SA. © 2016 John Wiley & Sons Ltd.

Ultra-low-mass flexible planar solar arrays using 50-micron-thick solar cells

NASA Technical Reports Server (NTRS)

Costogue, E. N.; Rayl, G.

1978-01-01

A conceptual design study has been completed which has shown the feasibility of ultra-low-mass planar solar arrays with specific power of 200 watts/kilogram. The beginning of life (BOL) power output of the array designs would be 10 kW at 1 astronomical unit (AU) and a 55C deg operating temperature. Two designs were studied: a retractable rollout design and a non-retractable fold-out. The designs employed a flexible low-mass blanket and low-mass structures. The blanket utilized 2 x 2 cm high-efficiency (13.5% at 28C deg AM0), ultra-thin (50 micron), silicon solar cells protected by thin (75 micron) plastic encapsulants. The structural design utilized the 'V'-stiffened approach which allows a lower mass boom to be used. In conjunction with the conceptual design, modules using the thin cells and plastic encapsulant were designed and fabricated.

Integration of Engine, Plume, and CFD Analyses in Conceptual Design of Low-Boom Supersonic Aircraft

NASA Technical Reports Server (NTRS)

Li, Wu; Campbell, Richard; Geiselhart, Karl; Shields, Elwood; Nayani, Sudheer; Shenoy, Rajiv

2009-01-01

This paper documents an integration of engine, plume, and computational fluid dynamics (CFD) analyses in the conceptual design of low-boom supersonic aircraft, using a variable fidelity approach. In particular, the Numerical Propulsion Simulation System (NPSS) is used for propulsion system cycle analysis and nacelle outer mold line definition, and a low-fidelity plume model is developed for plume shape prediction based on NPSS engine data and nacelle geometry. This model provides a capability for the conceptual design of low-boom supersonic aircraft that accounts for plume effects. Then a newly developed process for automated CFD analysis is presented for CFD-based plume and boom analyses of the conceptual geometry. Five test cases are used to demonstrate the integrated engine, plume, and CFD analysis process based on a variable fidelity approach, as well as the feasibility of the automated CFD plume and boom analysis capability.

Guidelines for conceptual design and evaluation of aquifer thermal energy storage

NASA Astrophysics Data System (ADS)

Meyer, C. F.; Hauz, W.

1980-10-01

Guidelines are presented for use as a tool by those considering application of aquifer thermal energy storage (ATES) technology. The guidelines assist utilities, municipalities, industries, and other entities in the conceptual design and evaluation of systems employing ATES. The potential benefits of ATES are described, an overview is presented of the technology and its applications, and rules of thumb are provided for quickly judging whether a proposed project has sufficient promise to warrant detailed conceptual design and evaluation. The characteristics of sources and end uses of heat and chill which are seasonally mismatched and may benefit from ATES are discussed. Storage and transport subsystems and their expected performance and cost are described. A methodology is presented for conceptual design of an ATES system and evaluation of its technical and economic feasibility in terms of energy conservation, cost savings, fuel substitution, improved dependability of supply, and abatement of pollution.

Haiti: Feasibility of Waste-to-Energy Options at the Trutier Waste Site

DOE Office of Scientific and Technical Information (OSTI.GOV)

Conrad, M. D.; Hunsberger, R.; Ness, J. E.

2014-08-01

This report provides further analysis of the feasibility of a waste-to-energy (WTE) facility in the area near Port-au-Prince, Haiti. NREL's previous analysis and reports identified anaerobic digestion (AD) as the optimal WTE technology at the facility. Building on the prior analyses, this report evaluates the conceptual financial and technical viability of implementing a combined waste management and electrical power production strategy by constructing a WTE facility at the existing Trutier waste site north of Port-au-Prince.

Perceptions of the feasibility and acceptability of a smartphone application for the treatment of binge eating disorders: Qualitative feedback from a user population and clinicians.

PubMed

Juarascio, Adrienne S; Goldstein, Stephanie P; Manasse, Stephanie M; Forman, Evan M; Butryn, Meghan L

2015-10-01

Binge eating, a major public health problem, is characterized by recurrent episodes of out-of-control eating in which an individual consumes an unusually large amount of food in a discrete time period. Limitations of existing treatments for binge eating (both in-person psychotherapy and guided self-help) indicate that smartphone applications (apps) may be an ideal alternative or enhancement. An app for binge eating could aid treatment dissemination, engagement, and/or compliance. However, no research to date has examined user perceptions of a therapeutic app for binge eating, which is critical for development. The purposes of the current study were to conceptualize a potential app for binge eating and obtain feedback regarding feasibility and acceptability from target users (i.e., individuals with binge eating) and clinicians specializing in the treatment of binge eating. Our team conceptualized a smartphone app that contained self-help material, functions to monitor behavior, and provisions of in-the-moment interventions. We presented this app (e.g., feature explanations, mock screen shots) through phone interviews with clinicians who specialize in the treatment of binge eating (n=10), and focus groups with individuals experiencing binge eating (n=11). Participants were asked to discuss customization, user burden, terminology, attrition, data visualization, comprehensiveness, reminders, feasibility, acceptability, and perceived effectiveness of the proposed app. Thematic analyses were conducted from qualitative data (e.g., audio recordings and interview notes) obtained via the focus groups and interviews. Results indicated that our proposed app would be highly feasible and acceptable to users and clinicians, though concerns about the degree of personalization and customizability were noted. The current study details highly specific feedback and ideas regarding essential app features from target users and clinicians. This information is critical for the development of future apps to treat binge eating. Ways in which data obtained from the current study may be generalized to the development of therapeutic apps for other psychological disorders is discussed. Copyright © 2015 Elsevier Ireland Ltd. All rights reserved.

Perceptions of the feasibility and acceptability of a smartphone application for the treatment of binge eating disorders: Qualitative feedback from a user population and clinicians

PubMed Central

Goldstein, Stephanie P.; Manasse, Stephanie M.; Forman, Evan M.; Butryn, Meghan L.

2016-01-01

Background Binge eating, a major public health problem, is characterized by recurrent episodes of out-of-control eating in which an individual consumes an unusually large amount of food in a discrete time period. Limitations of existing treatments for binge eating (both in-person psychotherapy and guided self-help) indicate that smartphone applications (apps) may be an ideal alternative or enhancement. An app for binge eating could aid treatment dissemination, engagement, and/or compliance. However, no research to date has examined user perceptions of a therapeutic app for binge eating, which is critical for development. Objectives The purposes of the current study were to conceptualize a potential app for binge eating and obtain feedback regarding feasibility and acceptability from target users (i.e., individuals with binge eating) and clinicians specializing in the treatment of binge eating. Methods Our team conceptualized a smartphone app that contained self-help material, functions to monitor behavior, and provisions of in-the-moment interventions. We presented this app (e.g., feature explanations, mock screen shots) through phone interviews with clinicians who specialize in the treatment of binge eating (n=10), and focus groups with individuals experiencing binge eating (n=11). Participants were asked to discuss customization, user burden, terminology, attrition, data visualization, comprehensiveness, reminders, feasibility, acceptability, and perceived effectiveness of the proposed app. Thematic analyses were conducted from qualitative data (e.g., audio recordings and interview notes) obtained via the focus groups and interviews. Results Results indicated that our proposed app would be highly feasible and acceptable to users and clinicians, though concerns about the degree of personalization and customizability were noted. Conclusions The current study details highly specific feedback and ideas regarding essential app features from target users and clinicians. This information is critical for the development of future apps to treat binge eating. Ways in which data obtained from the current study may be generalized to the development of therapeutic apps for other psychological disorders is discussed. PMID:26113461

Spacelab cryogenic propellant management experiment

NASA Technical Reports Server (NTRS)

Cady, E. C.

1976-01-01

The conceptual design of a Spacelab cryogen management experiment was performed to demonstrate toe desirability and feasibility of subcritical cryogenic fluid orbital storage and supply. A description of the experimental apparatus, definition of supporting requirements, procedures, data analysis, and a cost estimate are included.

Mini-Brayton heat source assembly design study. Volume 1: Space shuttle mission. [feasibility of Brayton isotope power system design

NASA Technical Reports Server (NTRS)

1973-01-01

Conceptual design definitions of a heat source assembly for use in nominal 500 watt electrical (W(e)) 1200 W(e)and 2000 W(e) mini-Brayton isotope power systems are reported. The HSA is an independent package which maintains thermal and nuclear control of an isotope fueled heat source and transfers the thermal energy to a Brayton rotating unit turbine-alternator-compressor power conversion unit.

Conceptual design of a thermal control system for an inflatable lunar habitat module

NASA Technical Reports Server (NTRS)

Gadkari, Ketan; Goyal, Sanjay K.; Vanniasinkam, Joseph

1991-01-01

NASA is considering the establishment of a manned lunar base within the next few decades. To house and protect the crew from the harsh lunar environment, a habitat is required. A proposed habitat is an spherical, inflatable module. Heat generated in the module must be rejected to maintain a temperature suitable for human habitation. This report presents a conceptual design of a thermal control system for an inflatable lunar module. The design solution includes heat acquisition, heat transport, and heat rejection subsystems. The report discusses alternative designs and design solutions for each of the three subsystems mentioned above. Alternative subsystems for heat acquisition include a single water-loop, a single air-loop, and a double water-loop. The vapor compression cycle, vapor absorption cycle, and metal hydride absorption cycle are the three alternative transport subsystems. Alternative rejection subsystems include flat plate radiators, the liquid droplet radiator, and reflux boiler radiators. Feasibility studies on alternatives of each subsystem showed that the single water-loop, the vapor compression cycle, and the reflux boiler radiator were the most feasible alternatives. The design team combined the three subsystems to come up with an overall system design. Methods of controlling the system to adapt it for varying conditions within the module and in the environment are presented. Finally, the report gives conclusions and recommendations for further study of thermal control systems for lunar applications.

A Conceptual Design For A Spaceborne 3D Imaging Lidar

NASA Technical Reports Server (NTRS)

Degnan, John J.; Smith, David E. (Technical Monitor)

2002-01-01

First generation spaceborne altimetric approaches are not well-suited to generating the few meter level horizontal resolution and decimeter accuracy vertical (range) resolution on the global scale desired by many in the Earth and planetary science communities. The present paper discusses the major technological impediments to achieving few meter transverse resolutions globally using conventional approaches and offers a feasible conceptual design which utilizes modest power kHz rate lasers, array detectors, photon-counting multi-channel timing receivers, and dual wedge optical scanners with transmitter point-ahead correction.

Assessing emotional well-being of children in a Honduran orphanage: feasibility of two screening tools.

PubMed

Debiasi, Laura B; Reynolds, Annette; Buckner, Ellen B

2012-01-01

The World Health Organization (WHO) has determined mental health in children to be a priority area for evidence-based interventions. Effective and efficient screening methods are needed to assess emotional well-being of children from diverse cultures. This descriptive study examined two tools for feasibility, sensitivity, cultural appropriateness, and cost/time effectiveness. Emotional well-being was conceptualized using the Roy Adaptation Model as part of the self-concept adaptive mode. Emotional indicators were measured from Human Figure Drawings. Anxiety was measured using a modification of the Revised Children's Manifest Anxiety Survey (RCMAS). The sample included 11 girls who were 7 to 12 years of age and recruited from a girls' orphanage in Honduras. Results indicated the Human Figure Drawings identified more children possibly at risk than the RCMAS. Human Figure Drawings were found to be a time/cost-effective, sensitive, and culturally appropriate means for measuring emotional well-being in the setting. This study contributes to nursing knowledge by demonstrating feasibility of the screening tools for measuring emotional well-being of children in varied cultures.

Extruded Tunnel Lining System : Phase 1. Conceptual Design and Feasibility Testing.

DOT National Transportation Integrated Search

1979-09-01

The Extruded Tunnel Lining System (ETLS) has been conceived as a means of continuously placing the final concrete tunnel lining directly behind a tunnel boring machine. The system will shorten the time required to excavate and line a tunnel section, ...

SAMICS support study. Volume 1: Cost account catalog

NASA Technical Reports Server (NTRS)

1977-01-01

The Jet Propulsion Laboratory (JPL) is examining the feasibility of a new industry to produce photovoltaic solar energy collectors similar to those used on spacecraft. To do this, a standardized costing procedure was developed. The Solar Array Manufacturing Industry Costing Standards (SAMICS) support study supplies the following information: (1) SAMICS critique; (2) Standard data base--cost account structure, expense item costs, inflation rates, indirect requirements relationships, and standard financial parameter values; (3) Facilities capital cost estimating relationships; (4) Conceptual plant designs; (5) Construction lead times; (6) Production start-up times; (7) Manufacturing price estimates.

Vessel Cold-Ironing Using a Barge Mounted PEM Fuel Cell: Project Scoping and Feasibility.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pratt, Joseph William; Harris, Aaron P.

2013-01-01

A barge-mounted hydrogen-fueled proton exchange membrane (PEM) fuel cell system has the potential to reduce emissions and fossil fuel use of maritime vessels in and around ports. This study determines the technical feasibility of this concept and examines specific options on the U.S. West Coast for deployment practicality and potential for commercialization.The conceptual design of the system is found to be straightforward and technically feasible in several configurations corresponding to various power levels and run times.The most technically viable and commercially attractive deployment options were found to be powering container ships at berth at the Port of Tacoma and/or Seattle,more » powering tugs at anchorage near the Port of Oakland, and powering refrigerated containers on-board Hawaiian inter-island transport barges. Other attractive demonstration options were found at the Port of Seattle, the Suisun Bay Reserve Fleet, the California Maritime Academy, and an excursion vessel on the Ohio River.« less

The use of quizStar application for online examination in basic physics course

NASA Astrophysics Data System (ADS)

Kustijono, R.; Budiningarti, H.

2018-03-01

The purpose of the study is to produce an online Basic Physics exam system using the QuizStar application. This is a research and development with ADDIE model. The steps are: 1) analysis; 2) design; 3) development; 4) implementation; 5) evaluation. System feasibility is reviewed for its validity, practicality, and effectiveness. The subjects of research are 60 Physics Department students of Universitas Negeri Surabaya. The data analysis used is a descriptive statistic. The validity, practicality, and effectiveness scores are measured using a Likert scale. Criteria feasible if the total score of all aspects obtained is ≥ 61%. The results obtained from the online test system by using QuizStar developed are 1) conceptually feasible to use; 2) the system can be implemented in the Basic Physics assessment process, and the existing constraints can be overcome; 3) student's response to system usage is in a good category. The results conclude that QuizStar application is eligible to be used for online Basic Physics exam system.

Conceptual Design of Low-Boom Aircraft with Flight Trim Requirement

NASA Technical Reports Server (NTRS)

Ordaz, Irian; Geiselhart, Karl A.; Fenbert, James W.

2014-01-01

A new low-boom target generation approach is presented which allows the introduction of a trim requirement during the early conceptual design of supersonic aircraft. The formulation provides an approximation of the center of pressure for a presumed aircraft configuration with a reversed equivalent area matching a low-boom equivalent area target. The center of pressure is approximated from a surrogate lift distribution that is based on the lift component of the classical equivalent area. The assumptions of the formulation are verified to be sufficiently accurate for a supersonic aircraft of high fineness ratio through three case studies. The first two quantify and verify the accuracy and the sensitivity of the surrogate center of pressure corresponding to shape deformation of lifting components. The third verification case shows the capability of the approach to achieve a trim state while maintaining the low-boom characteristics of a previously untrimmed configuration. Finally, the new low-boom target generation approach is demonstrated through the early conceptual design of a demonstrator concept that is low-boom feasible, trimmed, and stable in cruise.

Cooled variable-area radial turbine technology program

NASA Technical Reports Server (NTRS)

Large, G. D.; Meyer, L. J.

1982-01-01

The objective of this study was a conceptual evaluation and design analyses of a cooled variable-area radial turbine capable of maintaining nearly constant high efficiency when operated at a constant speed and pressure ratio over a range of flows corresponding to 50- to 100-percent maximum engine power. The results showed that a 1589K (2400 F) turbine was feasible that would satisfy a 4000-hour duty cycle life goal. The final design feasibility is based on 1988 material technology goals. A peak aerodynamic stage total efficiency of 0.88 was predicted at 100 percent power. Two candidate stators were identified: an articulated trailing-edge and a locally movable sidewall. Both concepts must be experimentally evaluated to determine the optimum configuration. A follow-on test program is proposed for this evaluation.

Evaluation of the feasibility and viability of modular pumped storage hydro (m-PSH) in the United States

DOE Office of Scientific and Technical Information (OSTI.GOV)

Witt, Adam M.; Hadjerioua, Boualem; Martinez, Rocio

The viability of modular pumped storage hydro (m-PSH) is examined in detail through the conceptual design, cost scoping, and economic analysis of three case studies. Modular PSH refers to both the compactness of the project design and the proposed nature of product fabrication and performance. A modular project is assumed to consist of pre-fabricated standardized components and equipment, tested and assembled into modules before arrival on site. This technology strategy could enable m-PSH projects to deploy with less substantial civil construction and equipment component costs. The concept of m-PSH is technically feasible using currently available conventional pumping and turbine equipment,more » and may offer a path to reducing the project development cycle from inception to commissioning.« less

Preface to RIGiM 2009

NASA Astrophysics Data System (ADS)

Rolland, Colette; Yu, Eric; Salinesi, Camille; Castro, Jaelson

The use of intentional concepts, the notion of "goal" in particular, has been prominent in recent approaches to requirement engineering (RE). Goal-oriented frameworks and methods for requirements engineering (GORE) have been keynote topics in requirements engineering, conceptual modelling, and more generally in software engineering. What are the conceptual modelling foundations in these approaches? RIGiM (Requirements Intentions and Goals in Conceptual Modelling) aims to provide a forum for discussing the interplay between requirements engineering and conceptual modelling, and in particular, to investigate how goal- and intention-driven approaches help in conceptualising purposeful systems. What are the fundamental objectives and premises of requirements engineering and conceptual modelling respectively, and how can they complement each other? What are the demands on conceptual modelling from the standpoint of requirements engineering? What conceptual modelling techniques can be further taken advantage of in requirements engineering? What are the upcoming modelling challenges and issues in GORE? What are the unresolved open questions? What lessons are there to be learnt from industrial experiences? What empirical data are there to support the cost-benefit analysis when adopting GORE methods? Are there application domains or types of project settings for which goals and intentional approaches are particularly suitable or not suitable? What degree of formalization and automation, or interactivity is feasible and appropriate for what types of participants during requirements engineering?

Conceptual study of hypersonic airbreathing missiles

NASA Technical Reports Server (NTRS)

Hunt, J. L.; Lawing, P. L.; Marcum, D. C.; Cubbage, J. M.

1978-01-01

The purpose of this paper is to report recent results of an in-house conceptual study to evaluate the performance potential and research needs of airbreathing hypersonic missiles. An alkylated-borane (noncryogenic) fueled, dual-mode, ramjet/scramjet propulsion system structured with a Rene 41 inlet and a carbon-carbon combustor was assumed along with a Lockalloy heat sink fuselage structure and beryllium wings and control surfaces. Performance for an air-launched baseline missile with a 961 pound staging weight containing a 100 pound payload indicated excellent long range cruise, moderate acceleration and high maneuverability potential. A sizing study indicates that Mach 6 cruise ranges of the order of 2500 nautical miles for payloads of 300 pounds can be achieved with moderate size missile carry weights (9000 lbs.). Aerodynamic heating analyses indicate that unprotected heat-sink structures with internal insulation are feasible for ranges of several hundred miles. For ranges of several thousands of miles a multiwall radiation shield (Inconel/titanium) was selected for protection of the internally insulated heat sink structure.

Planning an organizational wellness initiative at a multi-state social service agency.

PubMed

Miller, J Jay; Grise-Owens, Erlene; Addison, Donia; Marshall, Midaya; Trabue, Donna; Escobar-Ratliff, Laura

2016-06-01

Increasingly, organizations in general, and social service organizations, specifically, are recognizing the importance of planning and evaluating organizational wellness initiatives. Yet, few participatory models for carrying out these aims exist. For this study, researchers utilized concept mapping (CM) to explicate a conceptual framework for planning, and subsequently evaluating, a wellness initiative at a multi-state social service organization. CM is a participatory approach that analyzes qualitative data via multi-dimensional scaling and hierarchical cluster analyses. Outputs include a number of visual depictions that allow researchers to explore complex relationships among sets of the data. Results from this study indicated that participants (N=64), all of whom were employees of the agency, conceptualized organizational wellness via an eight-cluster solution, or Concept Map. Priority areas of this framework, specifically importance and feasibility, were also explored. After a brief review of pertinent literature, this article explicates the CM methodology utilized in this study, describes results, discusses lessons learned, and identifies apt areas for future research. Copyright © 2016 Elsevier Ltd. All rights reserved.

Feasibility study for a Cryogenic On-Orbit Liquid Depot-Storage, Acquisition and Transfer (COLD-SAT) satellite

NASA Technical Reports Server (NTRS)

Rybak, S. C.; Willen, G. S.; Follett, W. H.; Hanna, G. J.; Cady, E. C.; Distefano, E.; Meserole, J. S.

1990-01-01

This feasibility study presents the conceptual design of a spacecraft for performing a series of cryogenic fluid management flight experiments. This spacecraft, the Cryogenic On-Orbit Liquid Depot-Storage, Acquisition, and Transfer (COLD-SAT) satellite, will use liquid hydrogen as the test fluid, be launched on a Delta expendable launch vehicle, and conduct a series of experiments over a two to three month period. These experiments will investigate the physics of subcritical cryogens in the low gravity space environment to characterize their behavior and to correlate the data with analytical and numerical models of in-space cryogenic fluid management systems. Primary technologies addressed by COLD-SAT are: (1) pressure control; (2) chilldown; (3) no-vent fill; (4) liquid acquisition device fill; (5) pressurization; (6) low-g fill and drain; (7) liquid acquisition device expulsion; (8) line chilldown; (9) thermodynamic state control; and (10) fluid dumping.

Definition of smolder experiments for Spacelab

NASA Technical Reports Server (NTRS)

Summerfield, M.; Messina, N. A.; Ingram, L. S.

1979-01-01

The feasibility of conducting experiments in space on smoldering combustion was studied to conceptually design specific smoldering experiments to be conducted in the Shuttle/Spacelab System. Design information for identified experiment critical components is provided. The analytical and experimental basis for conducting research on smoldering phenomena in space was established. Physical descriptions of the various competing processes pertaining to smoldering combustion were identified. The need for space research was defined based on limitations of existing knowledge and limitations of ground-based reduced-gravity experimental facilities.

Application of Design of Experiments and Surrogate Modeling within the NASA Advanced Concepts Office, Earth-to-Orbit Design Process

NASA Technical Reports Server (NTRS)

Zwack, Matthew R.; Dees, Patrick D.; Holt, James B.

2016-01-01

Decisions made during early conceptual design can have a profound impact on life-cycle cost (LCC). Widely accepted that nearly 80% of LCC is committed. Decisions made during early design must be well informed. Advanced Concepts Office (ACO) at Marshall Space Flight Center aids in decision making for launch vehicles. Provides rapid turnaround pre-phase A and phase A studies. Provides customer with preliminary vehicle sizing information, vehicle feasibility, and expected performance.

New Bedford Harbor Superfund Project, Acushnet River Estuary Engineering Feasibility Study of Dredging and Dredged Material Disposal Alternatives. Report 9. Laboratory-Scale Application of Solidification/Stabilization Technology

DTIC Science & Technology

1989-01-01

force) per square inch to kilopascals, multiply by 6.894757. ** Flue - gas desulfurization . 27 1.0 sediment process, UCS measurements for solidified...Dredging Control Technoloqies 11 Evaluation of Conceptual Dredging and Disposal Alternatives 12 Executive Summary Destroy this report when no longer needed...solubility of metals by controlling the pH and alkalinity. Additional metal immobilization can be obtained by modify- ing the process to include

Feasibilty analyses of electroepitaxial research and development accomodations. Volume 1: Accommodations assessment

NASA Technical Reports Server (NTRS)

1983-01-01

A preliminary assessment of the feasibility of accommodating the on-orbit R&D requirements for electroepitaxial crystal growth using the Orbiter middeck, the Materials Experiment Assembly or the Get-Away Special cans was performed. The study is based on the proposed electroepitaxial growth of single crystals of gallium arsenide (GaAs). Baseline R&D requirements, synthesizing furnace and facility conceptual design requirements, accommodation requirements, preliminary compatibility assessments are established. The systems engineering approach employed for the individual assessments is outlined.

Feasibility study of an Integrated Program for Aerospace-vehicle Design (IPAD) system. Volume 4: Design of the IPAD system. Part 1: IPAD system design requirements, phase 1, task 2

NASA Technical Reports Server (NTRS)

Garrocq, C. A.; Hurley, M. J.

1973-01-01

System requirements, software elements, and hardware equipment required for an IPAD system are defined. An IPAD conceptual design was evolved, a potential user survey was conducted, and work loads for various types of interactive terminals were projected. Various features of major host computing systems were compared, and target systems were selected in order to identify the various elements of software required.

A Systems Approach to Research in Vocational Education.

ERIC Educational Resources Information Center

Miller, Larry E.

1991-01-01

A methodology to address "soft system" problems (those that are unstructured or fuzzy) has these steps: (1) mapping the problem; (2) constructing a root definition; (3) applying conceptual models; (4) comparing models to the real world; and (5) finding and implementing feasible solutions. (SK)

Conceptual design of flapping-wing micro air vehicles.

PubMed

Whitney, J P; Wood, R J

2012-09-01

Traditional micro air vehicles (MAVs) are miniature versions of full-scale aircraft from which their design principles closely follow. The first step in aircraft design is the development of a conceptual design, where basic specifications and vehicle size are established. Conceptual design methods do not rely on specific knowledge of the propulsion system, vehicle layout and subsystems; these details are addressed later in the design process. Non-traditional MAV designs based on birds or insects are less common and without well-established conceptual design methods. This paper presents a conceptual design process for hovering flapping-wing vehicles. An energy-based accounting of propulsion and aerodynamics is combined with a one degree-of-freedom dynamic flapping model. Important results include simple analytical expressions for flight endurance and range, predictions for maximum feasible wing size and body mass, and critical design space restrictions resulting from finite wing inertia. A new figure-of-merit for wing structural-inertial efficiency is proposed and used to quantify the performance of real and artificial insect wings. The impact of these results on future flapping-wing MAV designs is discussed in detail.

A Mission Concept to Study Multigenerational Mammalian Reproduction in Partial Gravity

NASA Technical Reports Server (NTRS)

Rodgers, Erica M.; Simon, Matthew A.; Chai, Patrick R.; Neilan, James H.; Stillwagen, Fred H.; Williams, Phillip A.; Lewis, Weston

2016-01-01

A team at NASA Langley Research Center conducted a study during which a conceptual space mission was designed. In this study, rodents are used as human analogs to gather biological and systems data in a relevant environment applicable to future settlements on Mars. The mission concept uniquely addresses the combined effects of long-durations (one-year or greater), autonomous and robotic operations, and biological responses to partial gravity with an emphasis on reproduction. The objectives of this study were to 1) understand challenges associated with designing an artificial gravity habitat that supports the reproduction and maturation of a large animal colony, 2) identify mission architectures and operational concepts to transport and maintain such a facility, and 3) identify fundamental science considerations for mammalian reproduction studies to inform vehicle design. A model demonstration unit was developed to visualize and test certain design concepts that resulted from these considerations. Three versions of this demonstration unit were built over the course of the study, each taking into account lessons learned from the previous version. This paper presents the updated baseline mission and spacecraft design concepts to achieve these objectives, with a specific emphasis on updates since publication in previous works. Analyses of the integrated system trades among the elements which make up the conceptual vehicle are described to address overall feasibility and identify potential integrated design opportunities. The latest iteration of the habitat robotics design and a conceptual design example for autonomous care of crew and systems are also presented. Finally, the conclusion of this conceptual design study, necessary future analyses to enable such a facility, and comments upon other applications of a similar exploration-focused research facilities are addressed.

Northwest passage: Trade route for large air cushion vehicles

NASA Technical Reports Server (NTRS)

Anderson, J. L.

1973-01-01

A conceptual vehicle and powerplant (10,000-ton) nuclear-powered air-cushion vehicle (ACV) that could open the Northwest Passage and other Arctic passages to commercial traffic is identified. The report contains a description of the conceptual vehicle, including the powerplant and operations, an assessment of technical feasibility, estimates of capital and operating costs, and identification of eligible cargo and markets. A comparison of the nuclear ACV freighter with nuclear container ships shows that for containerized or roll-on/roll-off cargo the ACV would provide greatly reduced transit time between North Atlantic and North Pacific ports at a competitive cost.

Development and Validation of Two Instruments Measuring Intrinsic, Extraneous, and Germane Cognitive Load.

PubMed

Klepsch, Melina; Schmitz, Florian; Seufert, Tina

2017-01-01

Cognitive Load Theory is one of the most powerful research frameworks in educational research. Beside theoretical discussions about the conceptual parts of cognitive load, the main challenge within this framework is that there is still no measurement instrument for the different aspects of cognitive load, namely intrinsic, extraneous, and germane cognitive load. Hence, the goal of this paper is to develop a differentiated measurement of cognitive load. In Study 1 ( N = 97), we developed and analyzed two strategies to measure cognitive load in a differentiated way: (1) Informed rating: We trained learners in differentiating the concepts of cognitive load, so that they could rate them in an informed way. They were asked then to rate 24 different learning situations or learning materials related to either high or low intrinsic, extraneous, or germane load. (2) Naïve rating: For this type of rating of cognitive load we developed a questionnaire with two to three items for each type of load. With this questionnaire, the same learning situations had to be rated. In the second study ( N = between 65 and 95 for each task), we improved the instrument for the naïve rating. For each study, we analyzed whether the instruments are reliable and valid, for Study 1, we also checked for comparability of the two measurement strategies. In Study 2, we conducted a simultaneous scenario based factor analysis. The informed rating seems to be a promising strategy to assess the different aspects of cognitive load, but it seems not economic and feasible for larger studies and a standardized training would be necessary. The improved version of the naïve rating turned out to be a useful, feasible, and reliable instrument. Ongoing studies analyze the conceptual validity of this measurement with up to now promising results.

Scaling Studies for Advanced High Temperature Reactor Concepts, Final Technical Report: October 2014—December 2017

DOE Office of Scientific and Technical Information (OSTI.GOV)

Woods, Brian; Gutowska, Izabela; Chiger, Howard

Computer simulations of nuclear reactor thermal-hydraulic phenomena are often used in the design and licensing of nuclear reactor systems. In order to assess the accuracy of these computer simulations, computer codes and methods are often validated against experimental data. This experimental data must be of sufficiently high quality in order to conduct a robust validation exercise. In addition, this experimental data is generally collected at experimental facilities that are of a smaller scale than the reactor systems that are being simulated due to cost considerations. Therefore, smaller scale test facilities must be designed and constructed in such a fashion tomore » ensure that the prototypical behavior of a particular nuclear reactor system is preserved. The work completed through this project has resulted in scaling analyses and conceptual design development for a test facility capable of collecting code validation data for the following high temperature gas reactor systems and events— 1. Passive natural circulation core cooling system, 2. pebble bed gas reactor concept, 3. General Atomics Energy Multiplier Module reactor, and 4. prismatic block design steam-water ingress event. In the event that code validation data for these systems or events is needed in the future, significant progress in the design of an appropriate integral-type test facility has already been completed as a result of this project. Where applicable, the next step would be to begin the detailed design development and material procurement. As part of this project applicable scaling analyses were completed and test facility design requirements developed. Conceptual designs were developed for the implementation of these design requirements at the Oregon State University (OSU) High Temperature Test Facility (HTTF). The original HTTF is based on a ¼-scale model of a high temperature gas reactor concept with the capability for both forced and natural circulation flow through a prismatic core with an electrical heat source. The peak core region temperature capability is 1400°C. As part of this project, an inventory of test facilities that could be used for these experimental programs was completed. Several of these facilities showed some promise, however, upon further investigation it became clear that only the OSU HTTF had the power and/or peak temperature limits that would allow for the experimental programs envisioned herein. Thus the conceptual design and feasibility study development focused on examining the feasibility of configuring the current HTTF to collect validation data for these experimental programs. In addition to the scaling analyses and conceptual design development, a test plan was developed for the envisioned modified test facility. This test plan included a discussion on an appropriate shakedown test program as well as the specific matrix tests. Finally, a feasibility study was completed to determine the cost and schedule considerations that would be important to any test program developed to investigate these designs and events.« less

Specimens and Reusable Fixturing for Testing Advanced Aeropropulsion Materials Under In-Plane Biaxial Loading. Part 1; Results of Conceptual Design Study

NASA Technical Reports Server (NTRS)

Ellis, J. R.; Sandlass, G. S.; Bayyari, M.

2001-01-01

A design study was undertaken to investigate the feasibility of using simple specimen designs and reusable fixturing for in-plane biaxial tests planned for advanced aeropropulsion materials. Materials of interest in this work include: advanced metallics, polymeric matrix composites, metal and intermetallic matrix composites, and ceramic matrix composites. Early experience with advanced metallics showed that the cruciform specimen design typically used in this type of testing was impractical for these materials, primarily because of concerns regarding complexity and cost. The objective of this research was to develop specimen designs, fixturing, and procedures which would allow in-plane biaxial tests to be conducted on a wide range of aeropropulsion materials while at the same time keeping costs within acceptable limits. With this goal in mind. a conceptual design was developed centered on a specimen incorporating a relatively simple arrangement of slots and fingers for attachment and loading purposes. The ANSYS finite element code was used to demonstrate the feasibility of the approach and also to develop a number of optimized specimen designs. The same computer code was used to develop the reusable fixturing needed to position and grip the specimens in the load frame. The design adopted uses an assembly of slotted fingers which can be reconfigured as necessary to obtain optimum biaxial stress states in the specimen gage area. Most recently, prototype fixturing was manufactured and is being evaluated over a range of uniaxial and biaxial loading conditions.

Combined Sustainability Assessment and Techno-Economic Analysis for the Production of Biomass-Derived High-Octane Gasoline Blendstock

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tan, Eric C. D.; Talmadge, Michael; Dutta, Abhijit

Conversion technologies for biomass to liquid hydrocarbon fuels are being actively developed. Converting biomass into advanced hydrocarbon fuels requires detailed assessments to help prioritize research; techno-economic analysis (TEA) is a long established tool used to assess feasibility and progress. TEA provides information needed to make informed judgments about the viability of any given conceptual conversion process; it is particularly useful to identify technical barriers and measure progress toward overcoming those barriers. Expansion of the cellulosic biofuels industry at the scale needed to meet the Renewable Fuel Standard goals is also expected to have environmental impacts. Hence, the success of themore » biofuels industry depends not only on economic viability, but also on environmental sustainability. A biorefinery process that is economically feasible but suffers from key sustainability drawbacks is not likely to represent a long-term solution to replace fossil-derived fuels. Overarching concerns like environmental sustainability need to be addressed for biofuels production. Combined TEA and environmental sustainability assessment of emerging pathways helps facilitate biorefinery designs that are both economically feasible and minimally impactful to the environment. This study focuses on environmental sustainability assessment and techno-economic analysis for the production of high-octane gasoline blendstock via gasification and methanol/dimethyl ether intermediates. Results from the conceptual process design with economic analysis, along with the quantification and assessment of the environmental sustainability, are presented and discussed. Sustainability metrics associated with the production of high-octane gasoline include carbon conversion efficiency, consumptive water use, life-cycle greenhouse gas emissions, fossil energy consumption, energy return on investment and net energy value.« less

Knowledge Productivity for Sustainable Innovation: Social Capital as HRD Target

ERIC Educational Resources Information Center

Ehlen, Corry; van der Klink, Marcel; Roentgen, Uta; Curfs, Emile; Boshuizen, Henny

2014-01-01

Purpose: The purpose of this paper is to test the feasibility of a conceptual model on relations between organisational innovation, knowledge productivity and social capital. It explores processes of knowledge productivity for sustainable innovation and associated HRD implications in knowledge intensive organisations, taking the perspective that…

Conceptual study of on orbit production of cryogenic propellants by water electrolysis

NASA Technical Reports Server (NTRS)

Moran, Matthew E.

1991-01-01

The feasibility is assessed of producing cryogenic propellants on orbit by water electrolysis in support of NASA's proposed Space Exploration Initiative (SEI) missions. Using this method, water launched into low earth orbit (LEO) would be split into gaseous hydrogen and oxygen by electrolysis in an orbiting propellant processor spacecraft. The resulting gases would then be liquified and stored in cryogenic tanks. Supplying liquid hydrogen and oxygen fuel to space vehicles by this technique has some possible advantages over conventional methods. The potential benefits are derived from the characteristics of water as a payload, and include reduced ground handling and launch risk, denser packaging, and reduced tankage and piping requirements. A conceptual design of a water processor was generated based on related previous studies, and contemporary or near term technologies required. Extensive development efforts would be required to adapt the various subsystems needed for the propellant processor for use in space. Based on the cumulative results, propellant production by on orbit water electrolysis for support of SEI missions is not recommended.

Study of quiet turbofan STOL aircraft for short haul transportation

NASA Technical Reports Server (NTRS)

Higgins, T. P.; Stout, E. G.; Sweet, H. S.

1973-01-01

Conceptual designs of Quiet Turbofan STOL Short-Haul Transport Aircraft for the mid-1980 time period are developed and analyzed to determine their technical, operational, and economic feasibility. A matrix of aircraft using various high-lift systems and design parameters are considered. Variations in aircraft characteristics, airport geometry and location, and operational techniques are analyzed systematically to determine their effects on the market, operating economics, and community acceptance. In these studies, the total systems approach is considered to be critically important in analyzing the potential of STOL aircraft to reduce noise pollution and alleviate the increasing air corridor and airport congestion.

Expert recommendations for implementing change (ERIC): protocol for a mixed methods study

PubMed Central

2014-01-01

Background Identifying feasible and effective implementation strategies that are contextually appropriate is a challenge for researchers and implementers, exacerbated by the lack of conceptual clarity surrounding terms and definitions for implementation strategies, as well as a literature that provides imperfect guidance regarding how one might select strategies for a given healthcare quality improvement effort. In this study, we will engage an Expert Panel comprising implementation scientists and mental health clinical managers to: establish consensus on a common nomenclature for implementation strategy terms, definitions and categories; and develop recommendations to enhance the match between implementation strategies selected to facilitate the use of evidence-based programs and the context of certain service settings, in this case the U.S. Department of Veterans Affairs (VA) mental health services. Methods/Design This study will use purposive sampling to recruit an Expert Panel comprising implementation science experts and VA mental health clinical managers. A novel, four-stage sequential mixed methods design will be employed. During Stage 1, the Expert Panel will participate in a modified Delphi process in which a published taxonomy of implementation strategies will be used to establish consensus on terms and definitions for implementation strategies. In Stage 2, the panelists will complete a concept mapping task, which will yield conceptually distinct categories of implementation strategies as well as ratings of the feasibility and effectiveness of each strategy. Utilizing the common nomenclature developed in Stages 1 and 2, panelists will complete an innovative menu-based choice task in Stage 3 that involves matching implementation strategies to hypothetical implementation scenarios with varying contexts. This allows for quantitative characterizations of the relative necessity of each implementation strategy for a given scenario. In Stage 4, a live web-based facilitated expert recommendation process will be employed to establish expert recommendations about which implementations strategies are essential for each phase of implementation in each scenario. Discussion Using a novel method of selecting implementation strategies for use within specific contexts, this study contributes to our understanding of implementation science and practice by sharpening conceptual distinctions among a comprehensive collection of implementation strategies. PMID:24669765

Feasibility and Preliminary Effects of an Intervention Targeting Schema Development for Caregivers of Newly Admitted Hospice Patients

PubMed Central

Mazurek Melnyk, Bernadette

2013-01-01

Abstract Background The transition to hospice care is a stressful experience for caregivers, who report high anxiety, unpreparedness, and lack of confidence. These sequelae are likely explained by the lack of an accurate cognitive schema, not knowing what to expect or how to help their loved one. Few interventions exist for this population and most do not measure preparedness, confidence, and anxiety using a schema building a conceptual framework for a new experience. Objective The purpose of this study was to test the feasibility and preliminary effects of an intervention program, Education and Skill building Intervention for Caregivers of Hospice patients (ESI-CH), using an innovative conceptual design that targets cognitive schema development and basic skill building for caregivers of loved ones newly admitted to hospice services. Design A pre-experimental one-group pre- and post-test study design was used. Eighteen caregivers caring for loved ones in their homes were recruited and twelve completed the pilot study. Depression, anxiety, activity restriction, preparedness, and beliefs/confidence were measured. Results Caregivers reported increased preparedness, more helpful beliefs, and more confidence about their ability to care for their loved one. Preliminary trends suggested decreased anxiety levels for the intervention group. Caregivers who completed the intervention program rated the program very good or excellent, thought the information was helpful and timely, and would recommend it to friends. Conclusions Results show promise that the ESI-CH program may assist as an evidence-based program to support caregivers in their role as a caregiver to a newly admitted hospice patient. PMID:23384244

Conceptual process design and techno-economic assessment of ex situ catalytic fast pyrolysis of biomass: A fixed bed reactor implementation scenario for future feasibility

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dutta, Abhijit; Schaidle, Joshua A.; Humbird, David

Ex situ catalytic fast pyrolysis of biomass is a promising route for the production of fungible liquid biofuels. There is significant ongoing research on the design and development of catalysts for this process. However, there are a limited number of studies investigating process configurations and their effects on biorefinery economics. Herein we present a conceptual process design with techno-economic assessment; it includes the production of upgraded bio-oil via fixed bed ex situ catalytic fast pyrolysis followed by final hydroprocessing to hydrocarbon fuel blendstocks. This study builds upon previous work using fluidized bed systems, as detailed in a recent design reportmore » led by the National Renewable Energy Laboratory (NREL/TP-5100-62455); overall yields are assumed to be similar, and are based on enabling future feasibility. Assuming similar yields provides a basis for easy comparison and for studying the impacts of areas of focus in this study, namely, fixed bed reactor configurations and their catalyst development requirements, and the impacts of an inline hot gas filter. A comparison with the fluidized bed system shows that there is potential for higher capital costs and lower catalyst costs in the fixed bed system, leading to comparable overall costs. The key catalyst requirement is to enable the effective transformation of highly oxygenated biomass into hydrocarbons products with properties suitable for blending into current fuels. Potential catalyst materials are discussed, along with their suitability for deoxygenation, hydrogenation and C–C coupling chemistry. This chemistry is necessary during pyrolysis vapor upgrading for improved bio-oil quality, which enables efficient downstream hydroprocessing; C–C coupling helps increase the proportion of diesel/jet fuel range product. One potential benefit of fixed bed upgrading over fluidized bed upgrading is catalyst flexibility, providing greater control over chemistry and product composition. Since this study is based on future projections, the impacts of uncertainties in the underlying assumptions are quantified via sensitivity analysis. As a result, this analysis indicates that catalyst researchers should prioritize by: carbon efficiency > catalyst cost > catalyst lifetime, after initially testing for basic operational feasibility.« less

Conceptual process design and techno-economic assessment of ex situ catalytic fast pyrolysis of biomass: A fixed bed reactor implementation scenario for future feasibility

DOE PAGES

Dutta, Abhijit; Schaidle, Joshua A.; Humbird, David; ...

2015-10-06

Ex situ catalytic fast pyrolysis of biomass is a promising route for the production of fungible liquid biofuels. There is significant ongoing research on the design and development of catalysts for this process. However, there are a limited number of studies investigating process configurations and their effects on biorefinery economics. Herein we present a conceptual process design with techno-economic assessment; it includes the production of upgraded bio-oil via fixed bed ex situ catalytic fast pyrolysis followed by final hydroprocessing to hydrocarbon fuel blendstocks. This study builds upon previous work using fluidized bed systems, as detailed in a recent design reportmore » led by the National Renewable Energy Laboratory (NREL/TP-5100-62455); overall yields are assumed to be similar, and are based on enabling future feasibility. Assuming similar yields provides a basis for easy comparison and for studying the impacts of areas of focus in this study, namely, fixed bed reactor configurations and their catalyst development requirements, and the impacts of an inline hot gas filter. A comparison with the fluidized bed system shows that there is potential for higher capital costs and lower catalyst costs in the fixed bed system, leading to comparable overall costs. The key catalyst requirement is to enable the effective transformation of highly oxygenated biomass into hydrocarbons products with properties suitable for blending into current fuels. Potential catalyst materials are discussed, along with their suitability for deoxygenation, hydrogenation and C–C coupling chemistry. This chemistry is necessary during pyrolysis vapor upgrading for improved bio-oil quality, which enables efficient downstream hydroprocessing; C–C coupling helps increase the proportion of diesel/jet fuel range product. One potential benefit of fixed bed upgrading over fluidized bed upgrading is catalyst flexibility, providing greater control over chemistry and product composition. Since this study is based on future projections, the impacts of uncertainties in the underlying assumptions are quantified via sensitivity analysis. As a result, this analysis indicates that catalyst researchers should prioritize by: carbon efficiency > catalyst cost > catalyst lifetime, after initially testing for basic operational feasibility.« less

Advanced Systems for Preprocessing and Characterizing Coal-Biomass Mixtures as Next-Generation Fuels and Feedstocks

DOE Office of Scientific and Technical Information (OSTI.GOV)

Karmis, Michael; Luttrell, Gerald; Ripepi, Nino

The research activities presented in this report are intended to address the most critical technical challenges pertaining to coal-biomass briquette feedstocks. Several detailed investigations were conducted using a variety of coal and biomass feedstocks on the topics of (1) coal-biomass briquette production and characterization, (2) gasification of coal-biomass mixtures and briquettes, (3) combustion of coal-biomass mixtures and briquettes, and (4) conceptual engineering design and economic feasibility of briquette production. The briquette production studies indicate that strong and durable co-firing feedstocks can be produced by co-briquetting coal and biomass resources commonly available in the United States. It is demonstrated that binderlessmore » coal-biomass briquettes produced at optimized conditions exhibit very high strength and durability, which indicates that such briquettes would remain competent in the presence of forces encountered in handling, storage and transportation. The gasification studies conducted demonstrate that coal-biomass mixtures and briquettes are exceptional gasification feedstocks, particularly with regard to the synergistic effects realized during devolatilization of the blended materials. The mixture combustion studies indicate that coal-biomass mixtures are exceptional combustion feedstocks, while the briquette combustion study indicates that the use of blended briquettes reduces NO x, CO 2, and CO emissions, and requires the least amount of changes in the operating conditions of an existing coal-fired power plant. Similar results were obtained for the physical durability of the pilot-scale briquettes compared to the bench-scale tests. Finally, the conceptual engineering and feasibility analysis study for a commercial-scale briquetting production facility provides preliminary flowsheet and cost simulations to evaluate the various feedstocks, equipment selection and operating parameters.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rigali, Mark J.; Pye, Steven; Hardin, Ernest

This study considers the feasibility of large diameter deep boreholes for waste disposal. The conceptual approach considers examples of deep large diameter boreholes that have been successfully drilled, and also other deep borehole designs proposed in the literature. The objective for large diameter boreholes would be disposal of waste packages with diameters of 22 to 29 inches, which could enable disposal of waste forms such as existing vitrified high level waste. A large-diameter deep borehole design option would also be amenable to other waste forms including calcine waste, treated Na-bonded and Na-bearing waste, and Cs and Sr capsules.

Feasibility study of an Integrated Program for Aerospace-vehicle Design (IPAD) system. Volume 5: Design of the IPAD system. Part 2: System design. Part 3: General purpose utilities, phase 1, task 2

NASA Technical Reports Server (NTRS)

Garrocq, C. A.; Hurley, M. J.

1973-01-01

Viable designs are presented of various elements of the IPAD framework software, data base management system, and required new languages in relation to the capabilities of operating systems software. A thorough evaluation was made of the basic systems functions to be provide by each software element, its requirements defined in the conceptual design, the operating systems features affecting its design, and the engineering/design functions which it was intended to enhance.

Evaluation of supercritical cryogen storage and transfer systems for future NASA missions

NASA Technical Reports Server (NTRS)

Arif, Hugh; Aydelott, John C.; Chato, David J.

1990-01-01

Conceptual designs of Space Transportation Vehicles (STV), and their orbital servicing facilities, that utilize supercritical, single phase, cryogenic propellant were established and compared with conventional subcritical, two phases, STV concepts. The analytical study was motivated by the desire to avoid fluid management problems associated with the storage, acquisition and transfer of subcritical liquid oxygen and hydrogen propellants in the low gravity environment of space. Although feasible, the supercritical concepts suffer from STV weight penalties and propellant resupply system power requirements which make the concepts impractical.

Evaluation of supercritical cryogen storage and transfer systems for future NASA missions

NASA Technical Reports Server (NTRS)

Arif, Hugh; Aydelott, John C.; Chato, David J.

1989-01-01

Conceptual designs of Space Transportation Vehicles (STV), and their orbital servicing facilities, that utilize supercritical, single phase, cryogenic propellants were established and compared with conventional subcritical, two phase, STV concepts. The analytical study was motivated by the desire to avoid fluid management problems associated with the storage, acquisition and transfer of subcritical liquid oxygen and hydrogen propellants in the low gravity environment of space. Although feasible, the supercritical concepts suffer from STV weight penalties and propellant resupply system power requirements which make the concepts impractical.

New Bedford Harbor Superfund Project, Acushnet River Estuary Engineering Feasibility Study of Dredging and Dredged Material Disposal Alternatives. Report 11. Evaluation of Conceptual Dredging and Disposal Alternatives

DTIC Science & Technology

1989-07-01

Y -- ma ma"o DIVIDENDS~~ 13ATUR -P 313ARM CORPS OF ENGINEERS A D z-. - N K 4 F~~ 1 /V. E C 7- GENERAL NOTES: - Soundtags are in fget a td t enths aid...usoAdter ine stae. Til %format ion depicted on these saps represents Ihq results of surveyjs made on the dates ihdica ted Ogu Ce on Iy .e Couasderedtas

Feasibility study report for distribution dispatching center project 2nd stage for the Provincial Electricity Authority (PEA), Bangkok, Thailand, June 1998. Export trade information

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

The study concerns the Provincial Electricity Authority, a state agency within the Ministry of Interior that supplies electricity to 73 of Thailand`s provinces. The primary objective of this study is to help increase the ability of the Authority to meet the rapidly increasing demand for electric power within the Kingdom of Thailand in a reliable, safe and economic manner. This is Volume 1 and it consists of the following: (1) introduction; (2) assessment; (3) conceptual design; (4) economic and financial evaluation; (5) project plan; (6) Thailand impact; (7) industry review; (8) conclusion; and appendices.

In situ groundwater bioremediation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hazen, Terry C.

2009-02-01

In situ groundwater bioremediation of hydrocarbons has been used for more than 40 years. Most strategies involve biostimulation; however, recently bioaugmentation have been used for dehalorespiration. Aquifer and contaminant profiles are critical to determining the feasibility and strategy for in situ groundwater bioremediation. Hydraulic conductivity and redox conditions, including concentrations of terminal electron acceptors are critical to determine the feasibility and strategy for potential bioremediation applications. Conceptual models followed by characterization and subsequent numerical models are critical for efficient and cost effective bioremediation. Critical research needs in this area include better modeling and integration of remediation strategies with natural attenuation.

A Rapid, Flexible Approach to Conceptual Space Mission Tradespace Definition and Exploration

NASA Technical Reports Server (NTRS)

Girerd, Andre R.

2005-01-01

This paper provides an overview of the Mission Tradespace Tool (MTT), a methodology and software framework developed to improve JPL's early design process by offering a rapid, structured, and inexpensive way to identify feasible design architectures from a wide array of candidate architectures. There has been a growing consensus at JPL that to improve the quality of service offered to design customers it is desirable to explore a wide tradespace of candidate architectures prior to forming a conceptual design baseline. This paper describes the rationale behind the MTT's approach to meet this need. Notable features of the framework are introduced and explained.

An Early Conceptual Design And Feasibility Analysis Of A Nuclear-Powered Cargo Vessel

DTIC Science & Technology

2009-05-08

13 FIGURE 6: NS MUTSU ...NS MUTSU .........................................................15 TABLE 4: PERTINENT NAVAL ARCHITECTURAL DATA DATA FOR NS SEVMORPUT...was built in Japan. Similar to the NS Otto Hahn, the NS Mutsu was to be a research vessel as well as a cargo vessel. However, the NS Mutsu was

Applying the ecosystem services concept to public land management

Treesearch

Jeffrey D. Kline; Marisa J. Mazzota; Thomas A. Spies; Mark E. Harmon

2013-01-01

We examine challenges and opportunities involved in applying ecosystem services to public land management with an emphasis on national forests in the United States. We review historical forest management paradigms and related economic approaches, outline a conceptual framework defining the informational needs of forest managers, and consider the feasibility of its...

The Evaluation Design: Summer Courses, 1974. Technical Report Number Four.

ERIC Educational Resources Information Center

Bramble, William J., Ed.; Ausness, Claudine, Ed.

The Appalachian Education Satellite Project (AESP) was conceptualized in 1973 (1) to develop courses in reading and career-education instruction for teachers in the Appalachian region, and (2) to determine the feasibility of conducting such courses over a large geographical area via communication satellites. During the summer of 1974 nearly 600…

Conceptual Design of a Vertical Takeoff and Landing Unmanned Aerial Vehicle with 24-HR Endurance

NASA Technical Reports Server (NTRS)

Fredericks, William J.

2010-01-01

This paper describes a conceptual design study for a vertical takeoff and landing (VTOL) unmanned aerial vehicle (UAV) that is able to carry a 25-lb science payload for 24 hr and is able to land and take off at elevations as high as 15,000 ft without human intervention. In addition to the science payload, this vehicle must be able to carry a satellite communication system, and the vehicle must be able to be transported in a standard full-size pickup truck and assembled by only two operators. This project started with a brainstorming phase to devise possible vehicle configurations that might satisfy the requirements. A down select was performed to select a near-term solution and two advanced vehicle concepts that are better suited to the intent of the mission. Sensitivity analyses were also performed on the requirements and the technology levels to obtain a better understanding of the design space. This study found that within the study assumptions the mission is feasible; the selected concepts are recommended for further development.

Feasibility of new breeding techniques for organic farming.

PubMed

Andersen, Martin Marchman; Landes, Xavier; Xiang, Wen; Anyshchenko, Artem; Falhof, Janus; Østerberg, Jeppe Thulin; Olsen, Lene Irene; Edenbrandt, Anna Kristina; Vedel, Suzanne Elizabeth; Thorsen, Bo Jellesmark; Sandøe, Peter; Gamborg, Christian; Kappel, Klemens; Palmgren, Michael G

2015-07-01

Organic farming is based on the concept of working 'with nature' instead of against it; however, compared with conventional farming, organic farming reportedly has lower productivity. Ideally, the goal should be to narrow this yield gap. In this review, we specifically discuss the feasibility of new breeding techniques (NBTs) for rewilding, a process involving the reintroduction of properties from the wild relatives of crops, as a method to close the productivity gap. The most efficient methods of rewilding are based on modern biotechnology techniques, which have yet to be embraced by the organic farming movement. Thus, the question arises of whether the adoption of such methods is feasible, not only from a technological perspective, but also from conceptual, socioeconomic, ethical, and regulatory perspectives. Copyright © 2015 Elsevier Ltd. All rights reserved.

Conceptual design of thermal energy storage systems for near term electric utility applications

NASA Technical Reports Server (NTRS)

Hall, E. W.; Hausz, W.; Anand, R.; Lamarche, N.; Oplinger, J.; Katzer, M.

1979-01-01

Potential concepts for near term electric utility applications were identified. The most promising ones for conceptual design were evaluated for their economic feasibility and cost benefits. The screening process resulted in selecting two coal-fired and two nuclear plants for detailed conceptual design. The coal plants utilized peaking turbines and the nuclear plants varied the feedwater extraction to change power output. It was shown that the performance and costs of even the best of these systems could not compete in near term utility applications with cycling coal plants and typical gas turbines available for peaking power. Lower electricity costs, greater flexibility of operation, and other benefits can be provided by cycling coal plants for greater than 1500 hours of peaking or by gas turbines for less than 1500 hours if oil is available and its cost does not increase significantly.

Conceptual design for a lunar-base CELSS

NASA Technical Reports Server (NTRS)

Schwartzkopf, Steven H.; Cullingford, Hatice S.

1990-01-01

Future human exploration is key to the United States National Space Policy goal of maintaining a world leadership position in space. In the past, spacecraft life support systems have used open-loop technologies that were simple and sufficiently reliable to demonstrate the feasibility of spaceflight. A critical technology area needing development in support of both long duration missions and the establishment of lunar or planetary bases is regenerative life support. The information presented in this paper describes a conceptual design of a Lunar Base Controlled Ecological Life Support System (LCELSS) which supports a crew size ranging from 4 to 100. The system includes, or incorporates interfaces with, eight primary subsystems. An initial description of the Lunar-Base CELSS subsystems is provided within the framework of the conceptual design. The system design includes both plant (algae and higher plant) and animal species as potential food sources.

Expert systems for space power supply - Design, analysis, and evaluation

NASA Technical Reports Server (NTRS)

Cooper, Ralph S.; Thomson, M. Kemer; Hoshor, Alan

1987-01-01

The feasibility of applying expert systems to the conceptual design, analysis, and evaluation of space power supplies in particular, and complex systems in general is evaluated. To do this, the space power supply design process and its associated knowledge base were analyzed and characterized in a form suitable for computer emulation of a human expert. The existing expert system tools and the results achieved with them were evaluated to assess their applicability to power system design. Some new concepts for combining program architectures (modular expert systems and algorithms) with information about the domain were applied to create a 'deep' system for handling the complex design problem. NOVICE, a code to solve a simplified version of a scoping study of a wide variety of power supply types for a broad range of missions, has been developed, programmed, and tested as a concrete feasibility demonstration.

Using a High-Speed Camera to Measure the Speed of Sound

ERIC Educational Resources Information Center

Hack, William Nathan; Baird, William H.

2012-01-01

The speed of sound is a physical property that can be measured easily in the lab. However, finding an inexpensive and intuitive way for students to determine this speed has been more involved. The introduction of affordable consumer-grade high-speed cameras (such as the Exilim EX-FC100) makes conceptually simple experiments feasible. Since the…

Understanding the Common Elements of Evidence-Based Practice: Misconceptions and Clinical Examples

ERIC Educational Resources Information Center

Chorpita, Bruce F.; Becker, Kimberly D.; Daleiden, Eric L.

2007-01-01

In this article, the authors proposed a distillation and matching model (DMM) that describes how evidence-based treatment operations can be conceptualized at a lower order level of analysis than simply by their manuals. Also referred to as the "common elements" approach, this model demonstrates the feasibility of coding and identifying the…

An Operations Management System for the Space Station

NASA Astrophysics Data System (ADS)

Rosenthal, H. G.

1986-09-01

This paper presents an overview of the conceptual design of an integrated onboard Operations Management System (OMS). Both hardware and software concepts are presented and the integrated space station network is discussed. It is shown that using currently available software technology, an integrated software solution for Space Station management and control, implemented with OMS software, is feasible.

An Experiment in Educational Technology: An Overview of the Appalachian Education Satellite Project. Technical Report Number 2.

ERIC Educational Resources Information Center

Bramble, William J., Ed.; Ausness, Claudine, Ed.

The Appalachian Education Satellite Project was conceptualized in 1973 (1) to develop courses in reading and career-education instruction for teachers in the Appalachian region, and (2) to determine the feasibility of conducting such courses over a large geographical area via communication satellites. The courses consist of pretaped video…

Prediction of forces and moments for flight vehicle control effectors. Part 1: Validation of methods for predicting hypersonic vehicle controls forces and moments

NASA Technical Reports Server (NTRS)

Maughmer, Mark D.; Ozoroski, L.; Ozoroski, T.; Straussfogel, D.

1990-01-01

Many types of hypersonic aircraft configurations are currently being studied for feasibility of future development. Since the control of the hypersonic configurations throughout the speed range has a major impact on acceptable designs, it must be considered in the conceptual design stage. The ability of the aerodynamic analysis methods contained in an industry standard conceptual design system, APAS II, to estimate the forces and moments generated through control surface deflections from low subsonic to high hypersonic speeds is considered. Predicted control forces and moments generated by various control effectors are compared with previously published wind tunnel and flight test data for three configurations: the North American X-15, the Space Shuttle Orbiter, and a hypersonic research airplane concept. Qualitative summaries of the results are given for each longitudinal force and moment and each control derivative in the various speed ranges. Results show that all predictions of longitudinal stability and control derivatives are acceptable for use at the conceptual design stage. Results for most lateral/directional control derivatives are acceptable for conceptual design purposes; however, predictions at supersonic Mach numbers for the change in yawing moment due to aileron deflection and the change in rolling moment due to rudder deflection are found to be unacceptable. Including shielding effects in the analysis is shown to have little effect on lift and pitching moment predictions while improving drag predictions.

Progress in the RAMI analysis of a conceptual LHCD system for DEMO

NASA Astrophysics Data System (ADS)

Mirizzi, F.

2014-02-01

Reliability, Availability, Maintainability and Inspectability (RAMI) concepts and techniques, that acquired great importance during the first manned space missions, have been progressively extended to industrial, scientific and consumer equipments to assure them satisfactory performances and lifetimes. In the design of experimental facilities, like tokamaks, mainly aimed at demonstrating validity and feasibility of scientific theories, RAMI analysis has been often left aside. DEMO, the future prototype fusion reactors, will be instead designed for steadily delivering electrical energy to commercial grids, so that the RAMI aspects will assume an absolute relevance since their initial design phases. A preliminary RAMI analysis of the LHCD system for the conceptual EU DEMO reactor is given in the paper.

A model to assess the feasibility of shifting reaction equilibrium by acetone removal in the transamination of ketones using 2-propylamine.

PubMed

Tufvesson, Pär; Bach, Christian; Woodley, John M

2014-02-01

Acetone removal by evaporation has been proposed as a simple and cheap way to shift the equilibrium in the biocatalytic asymmetric synthesis of optically pure chiral amines, when 2-propylamine is used as the amine donor. However, dependent on the system properties, this may or may not be a suitable strategy. To avoid excessive laboratory work a model was used to assess the process feasibility. The results from the current study show that a simple model of the acetone removal dependence on temperature and sparging gas flowrate can be developed and fits the experimental data well. The model for acetone removal was then coupled to a simple model for biocatalyst kinetics and also for loss of substrate ketone by evaporation. The three models were used to simulate the effects of varying the critical process parameters and reaction equilibrium constants (K eq) as well as different substrate ketone volatilities (Henry's constant). The simulations were used to estimate the substrate losses and also the maximum yield that could be expected. The approach was seen to give a clear indication for which target amines the acetone evaporation strategy would be feasible and for which amines it would not. The study also shows the value of a modeling approach in conceptual process design prior to entering a biocatalyst screening or engineering program to assess the feasibility of a particular process strategy for a given target product. © 2013 Wiley Periodicals, Inc.

Feasibility study for biomass power plants in Thailand. Volume 1. Main report. Export trade information

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

This study, conducted by Black & Veatch, was funded by the U.S. Trade and Development Agency. The report presents a technical and commercial analysis for the development of three nearly identical electricity generating facilities (biomass steam power plants) in the towns of Chachoengsao, Suphan Buri, and Pichit in Thailand. The Main Report is divided into the following sections: (1.0) Executive Study; (2.0) Project Objectives; (3.0) Review of Combustion Technology for Biomass Fueled Steam Generator Units; (4.0) Conceptual Design; (5.0) Plant Descriptions; (6.0) Plant Operations Staffing; (7.0) Project Schedule; (8.0) Project Cost Estimate; (9.0) Financial Analysis; Appendix - Financial Analysis.

Status of solid polymer electrolyte fuel cell technology and potential for transportation applications

NASA Astrophysics Data System (ADS)

McElroy, J. F.; Nuttall, L. J.

The solid polymer electrolyte (SPE) fuel cell represents the first fuel cell technology known to be used operationally. Current activities are mainly related to the development of a space regenerative fuel cell system for energy storage on board space stations, or other large orbiting vehicles and platforms. During 1981, a study was performed to determine the feasibility of using SPE fuel cells for automotive or other vehicular applications, using methanol as the fuel. The results of this study were very encouraging. Details concerning a conceptual automotive fuel cell power plant study are discussed, taking into account also a layout of major components for compact passenger car installation.

Expert Opinions on Improving Femicide Data Collection across Europe: A Concept Mapping Study.

PubMed

Vives-Cases, Carmen; Goicolea, Isabel; Hernández, Alison; Sanz-Barbero, Belen; Gill, Aisha K; Baldry, Anna Costanza; Schröttle, Monika; Stöckl, Heidi; Stoeckl, Heidi

2016-01-01

Femicide, defined as the killings of females by males because they are females, is becoming recognized worldwide as an important ongoing manifestation of gender inequality. Despite its high prevalence or widespread prevalence, only a few countries have specific registries about this issue. This study aims to assemble expert opinion regarding the strategies which might feasibly be employed to promote, develop and implement an integrated and differentiated femicide data collection system in Europe at both the national and international levels. Concept mapping methodology was followed, involving 28 experts from 16 countries in generating strategies, sorting and rating them with respect to relevance and feasibility. The experts involved were all members of the EU-Cost-Action on femicide, which is a scientific network of experts on femicide and violence against women across Europe. As a result, a conceptual map emerged, consisting of 69 strategies organized in 10 clusters, which fit into two domains: "Political action" and "Technical steps". There was consensus among participants regarding the high relevance of strategies to institutionalize national databases and raise public awareness through different stakeholders, while strategies to promote media involvement were identified as the most feasible. Differences in perceived priorities according to the level of human development index of the experts' countries were also observed.

Expert Opinions on Improving Femicide Data Collection across Europe: A Concept Mapping Study

PubMed Central

Vives-Cases, Carmen; Goicolea, Isabel; Hernández, Alison; Sanz-Barbero, Belen; Gill, Aisha K.; Baldry, Anna Costanza; Schröttle, Monika; Stoeckl, Heidi

2016-01-01

Femicide, defined as the killings of females by males because they are females, is becoming recognized worldwide as an important ongoing manifestation of gender inequality. Despite its high prevalence or widespread prevalence, only a few countries have specific registries about this issue. This study aims to assemble expert opinion regarding the strategies which might feasibly be employed to promote, develop and implement an integrated and differentiated femicide data collection system in Europe at both the national and international levels. Concept mapping methodology was followed, involving 28 experts from 16 countries in generating strategies, sorting and rating them with respect to relevance and feasibility. The experts involved were all members of the EU-Cost-Action on femicide, which is a scientific network of experts on femicide and violence against women across Europe. As a result, a conceptual map emerged, consisting of 69 strategies organized in 10 clusters, which fit into two domains: “Political action” and “Technical steps”. There was consensus among participants regarding the high relevance of strategies to institutionalize national databases and raise public awareness through different stakeholders, while strategies to promote media involvement were identified as the most feasible. Differences in perceived priorities according to the level of human development index of the experts’ countries were also observed. PMID:26859885

The SBIRT program matrix: a conceptual framework for program implementation and evaluation.

PubMed

Del Boca, Frances K; McRee, Bonnie; Vendetti, Janice; Damon, Donna

2017-02-01

Screening, Brief Intervention and Referral to Treatment (SBIRT) is a comprehensive, integrated, public health approach to the delivery of services to those at risk for the adverse consequences of alcohol and other drug use, and for those with probable substance use disorders. Research on successful SBIRT implementation has lagged behind studies of efficacy and effectiveness. This paper (1) outlines a conceptual framework, the SBIRT Program Matrix, to guide implementation research and program evaluation and (2) specifies potential implementation outcomes. Overview and narrative description of the SBIRT Program Matrix. The SBIRT Program Matrix has five components, each of which includes multiple elements: SBIRT services; performance sites; provider attributes; patient/client populations; and management structure and activities. Implementation outcomes include program adoption, acceptability, appropriateness, feasibility, fidelity, costs, penetration, sustainability, service provision and grant compliance. The Screening, Brief Intervention and Referral to Treatment Program Matrix provides a template for identifying, classifying and organizing the naturally occurring commonalities and variations within and across SBIRT programs, and for investigating which variables are associated with implementation success and, ultimately, with treatment outcomes and other impacts. © 2017 Society for the Study of Addiction.

At the cross-roads of participatory research and biomarker discovery in autism: the need for empirical data.

PubMed

Yusuf, Afiqah; Elsabbagh, Mayada

2015-12-15

Identifying biomarkers for autism can improve outcomes for those affected by autism. Engaging the diverse stakeholders in the research process using community-based participatory research (CBPR) can accelerate biomarker discovery into clinical applications. However, there are limited examples of stakeholder involvement in autism research, possibly due to conceptual and practical concerns. We evaluate the applicability of CBPR principles to biomarker discovery in autism and critically review empirical studies adopting these principles. Using a scoping review methodology, we identified and evaluated seven studies using CBPR principles in biomarker discovery. The limited number of studies in biomarker discovery adopting CBPR principles coupled with their methodological limitations suggests that such applications are feasible but challenging. These studies illustrate three CBPR themes: community assessment, setting global priorities, and collaboration in research design. We propose that further research using participatory principles would be useful in accelerating the pace of discovery and the development of clinically meaningful biomarkers. For this goal to be successful we advocate for increased attention to previously identified conceptual and methodological challenges to participatory approaches in health research, including improving scientific rigor and developing long-term partnerships among stakeholders.

Design study of wind turbines 50 kW to 3000 kW for electric utility applications: Analysis and design

NASA Technical Reports Server (NTRS)

1976-01-01

In the conceptual design task, several feasible wind generator systems (WGS) configurations were evaluated, and the concept offering the lowest energy cost potential and minimum technical risk for utility applications was selected. In the optimization task, the selected concept was optimized utilizing a parametric computer program prepared for this purpose. In the preliminary design task, the optimized selected concept was designed and analyzed in detail. The utility requirements evaluation task examined the economic, operational, and institutional factors affecting the WGS in a utility environment, and provided additional guidance for the preliminary design effort. Results of the conceptual design task indicated that a rotor operating at constant speed, driving an AC generator through a gear transmission is the most cost effective WGS configuration. The optimization task results led to the selection of a 500 kW rating for the low power WGS and a 1500 kW rating for the high power WGS.

Smartphone application for multi-phasic interventional trials in psychiatry: Technical design of a smart server.

PubMed

Zhang, Melvyn W B; Ho, Roger C M

2017-01-01

Smartphones and their accompanying applications are currently widely utilized in various healthcare interventions. Prior to the deployment of these tools for healthcare intervention, typically, proof of concept feasibility studies, as well as randomized trials are conducted to determine that these tools are efficacious prior to their actual implementation. In the field of psychiatry, most of the current interventions seek to compare smartphone based intervention against conventional care. There remains a paucity of research evaluating different forms of interventions using a single smartphone application. In the field of nutrition, there has been recent pioneering research demonstrating how a multi-phasic randomized controlled trial could be conducted using a single smartphone application. Despite the innovativeness of the previous smartphone conceptualization, there remains a paucity of technical information underlying the conceptualization that would support a multi-phasic interventional trial. It is thus the aim of the current technical note to share insights into an innovative server design that would enable the delivery of multi-phasic trials.

Study of quiet turbofan STOL aircraft for short-haul transportation. Volume 1: Summary

NASA Technical Reports Server (NTRS)

1974-01-01

Conceptual designs of Quiet Turbofan STOL Short-Haul Transport Aircraft for the mid-1980 time period are developed and analyzed to determine their technical, operational, and economic feasibility. A matrix of aircraft using various high-lift systems and design parameters are considered. Variations in aircraft characteristics, airport geometry and location, and operational techniques are analyzed systematically to determine their effects on the market, operating economics, and community acceptance. The total systems approach is considered to be critically important in analyzing the potential of STOL aircraft to reduce noise pollution and alleviate the increasing air corridor and airport congestion.

Development and Validation of Two Instruments Measuring Intrinsic, Extraneous, and Germane Cognitive Load

PubMed Central

Klepsch, Melina; Schmitz, Florian; Seufert, Tina

2017-01-01

Cognitive Load Theory is one of the most powerful research frameworks in educational research. Beside theoretical discussions about the conceptual parts of cognitive load, the main challenge within this framework is that there is still no measurement instrument for the different aspects of cognitive load, namely intrinsic, extraneous, and germane cognitive load. Hence, the goal of this paper is to develop a differentiated measurement of cognitive load. In Study 1 (N = 97), we developed and analyzed two strategies to measure cognitive load in a differentiated way: (1) Informed rating: We trained learners in differentiating the concepts of cognitive load, so that they could rate them in an informed way. They were asked then to rate 24 different learning situations or learning materials related to either high or low intrinsic, extraneous, or germane load. (2) Naïve rating: For this type of rating of cognitive load we developed a questionnaire with two to three items for each type of load. With this questionnaire, the same learning situations had to be rated. In the second study (N = between 65 and 95 for each task), we improved the instrument for the naïve rating. For each study, we analyzed whether the instruments are reliable and valid, for Study 1, we also checked for comparability of the two measurement strategies. In Study 2, we conducted a simultaneous scenario based factor analysis. The informed rating seems to be a promising strategy to assess the different aspects of cognitive load, but it seems not economic and feasible for larger studies and a standardized training would be necessary. The improved version of the naïve rating turned out to be a useful, feasible, and reliable instrument. Ongoing studies analyze the conceptual validity of this measurement with up to now promising results. PMID:29201011

The “Health Coaching” programme: a new patient-centred and visually supported approach for health behaviour change in primary care

PubMed Central

2013-01-01

Background Health related behaviour is an important determinant of chronic disease, with a high impact on public health. Motivating and assisting people to change their unfavourable health behaviour is thus a major challenge for health professionals. The objective of the study was to develop a structured programme of counselling in primary care practice, and to test its feasibility and acceptance among general practitioners (GPs) and their patients. Methods Our new concept integrates change of roles, shared responsibility, patient-centredness, and modern communication techniques—such as motivational interviewing. A new colour-coded visual communication tool is used for the purpose of leading through the 4-step counselling process. As doctors’ communication skills are crucial, communication training is a mandatory part of the programme. We tested the feasibility and acceptance of the “Health Coaching” programme with 20 GPs and 1045 patients, using questionnaires and semistructured interviewing techniques. The main outcomes were participation rates; the duration of counselling; patients’ self-rated behavioural change in their areas of choice; and ratings of motivational, conceptual, acceptance, and feasibility issues. Results In total, 37% (n=350) of the patients enrolled in step 1 completed the entire 4-Step counselling process, with each step taking 8–22 minutes. 50% of ratings (n=303) improved by one or two categories in the three-colour circle, and the proportion of favourable health behaviour ratings increased from 9% to 39%. The ratings for motivation, concept, acceptance, and feasibility of the “Health Coaching” programme were consistently high. Conclusions Our innovative, patient-centred counselling programme for health behaviour change was well accepted and feasible among patients and physicians in a primary care setting. Randomised controlled studies will have to establish cost-effectiveness and promote dissemination. PMID:23865509

The "Health Coaching" programme: a new patient-centred and visually supported approach for health behaviour change in primary care.

PubMed

Neuner-Jehle, Stefan; Schmid, Margareta; Grüninger, Ueli

2013-07-17

Health related behaviour is an important determinant of chronic disease, with a high impact on public health. Motivating and assisting people to change their unfavourable health behaviour is thus a major challenge for health professionals. The objective of the study was to develop a structured programme of counselling in primary care practice, and to test its feasibility and acceptance among general practitioners (GPs) and their patients. Our new concept integrates change of roles, shared responsibility, patient-centredness, and modern communication techniques-such as motivational interviewing. A new colour-coded visual communication tool is used for the purpose of leading through the 4-step counselling process. As doctors' communication skills are crucial, communication training is a mandatory part of the programme. We tested the feasibility and acceptance of the "Health Coaching" programme with 20 GPs and 1045 patients, using questionnaires and semistructured interviewing techniques. The main outcomes were participation rates; the duration of counselling; patients' self-rated behavioural change in their areas of choice; and ratings of motivational, conceptual, acceptance, and feasibility issues. In total, 37% (n=350) of the patients enrolled in step 1 completed the entire 4-Step counselling process, with each step taking 8-22 minutes. 50% of ratings (n=303) improved by one or two categories in the three-colour circle, and the proportion of favourable health behaviour ratings increased from 9% to 39%. The ratings for motivation, concept, acceptance, and feasibility of the "Health Coaching" programme were consistently high. Our innovative, patient-centred counselling programme for health behaviour change was well accepted and feasible among patients and physicians in a primary care setting. Randomised controlled studies will have to establish cost-effectiveness and promote dissemination.

Acquiring Science and Social Studies Knowledge in Kindergarten Through Fourth Grade: Conceptualization, Design, Implementation, and Efficacy Testing of Content-Area Literacy Instruction (CALI).

PubMed

Dombek, Jennifer; Crowe, Elizabeth C; Spencer, Mercedes; Tighe, Elizabeth L; Coffinger, Sean; Zargar, Elham; Wood, Taffeta; Petscher, Yaacov

2017-04-01

With national focus on reading and math achievement, science and social studies have received less instructional time. Yet, accumulating evidence suggests that content knowledge is an important predictor of proficient reading. Starting with a design study, we developed Content Area Literacy Instruction (CALI), as an individualized (or personalized) instructional program for kindergarteners through fourth graders to build science and social studies knowledge. We developed CALI to be implemented in general education classrooms, over multiple iterations (n=230 students), using principles of design-based implementation research. The aims were to develop CALI as a usable and feasible instructional program that would, potentially, improve science and social studies knowledge, and could be implemented during the literacy block without negatively affecting students' reading gains (i.e., no opportunity cost). We then evaluated the efficacy of CALI in a randomized controlled field trial with 418 students in kindergarten through fourth grade. Results reveal that CALI demonstrates promise as a useable and feasible instructional individualized general education program, and is efficacious in improving social studies ( d =2.2) and science ( d =2.1) knowledge, with some evidence of improving oral and reading comprehension skills ( d =.125).

Conceptual design of an orbital debris collector

NASA Technical Reports Server (NTRS)

Odonoghue, Peter (Editor); Brenton, Brian; Chambers, Ernest; Schwind, Thomas; Swanhart, Christopher; Williams, Thomas

1991-01-01

The current Lower Earth Orbit (LEO) environment has become overly crowded with space debris. An evaluation of types of debris is presented in order to determine which debris poses the greatest threat to operation in space, and would therefore provide a feasible target for removal. A target meeting these functional requirements was found in the Cosmos C-1B Rocket Body. These launchers are spent space transporters which constitute a very grave risk of collision and fragmentation in LEO. The motion and physical characteristics of these rocket bodies have determined the most feasible method of removal. The proposed Orbital Debris Collector (ODC) device is designed to attach to the Orbital Maneuvering Vehicle (OMV), which provides all propulsion, tracking, and power systems. The OMV/ODC combination, the Rocket Body Retrieval Vehicle (RBRV), will match orbits with the rocket body, use a spin table to match the rotational motion of the debris, capture it, despin it, and remove it from orbit by allowing it to fall into the Earth's atmosphere. A disposal analysis is presented to show how the debris will be deorbited into the Earth's atmosphere. The conceptual means of operation of a sample mission is described.

Feasibility Study for a Combined Radiation Environment in the ACRR-FRECII Cavity.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Parma, Edward J.

The objective of this report is to determine the feasibility of a combined pulsed - power accelerator machine, similar to HERMES - III, with the Annular Core Research Reactor (ACRR) Fueled - Ring External Cavity (FREC - II) in a new facility. The document is conceptual in nature, and includes some neutronic analysis that i llustrates that that the physics of such a concept would be feasible. There would still be many engineering design considerations and issues that would need to be investigated in order to determine the true viability of such a concept. This report does n ot addressmore » engineering design details, the cost of such a facility, or what would be required to develop the safety authorization of the concept. The radiation requirements for the "on - target" gamma - ray dose and dose rate are not addressed in this report . It is assumed that if the same general on - target specifications for a HERMES - III type machine could be met with the proposed concept, that the machine would b e considered highly useful as a radiation effects sciences platform. In general, the combined accelerator/ACRR reactor concept can be shown to be feasible with no major issues that would preclude the usefulness of such a facility. The new facility would provide a capability that currently does not exist in the radiation testing complex.« less

Embedded Wing Propulsion Conceptual Study

NASA Technical Reports Server (NTRS)

Kim, Hyun D.; Saunders, John D.

2003-01-01

As a part of distributed propulsion work under NASA's Revolutionary Aeropropulsion Concepts or RAC project, a new propulsion-airframe integrated vehicle concept called Embedded Wing Propulsion (EWP) is developed and examined through system and computational fluid dynamics (CFD) studies. The idea behind the concept is to fully integrate a propulsion system within a wing structure so that the aircraft takes full benefits of coupling of wing aerodynamics and the propulsion thrust stream. The objective of this study is to assess the feasibility of the EWP concept applied to large transport aircraft such as the Blended-Wing-Body aircraft. In this paper, some of early analysis and current status of the study are presented. In addition, other current activities of distributed propulsion under the RAC project are briefly discussed.

Integrating Women's Human Rights into Global Health Research: An Action Framework

PubMed Central

Kapungu, Chisina; Khare, Manorama H.; Lewis, Yvonne; Barlow-Mosha, Linda

2010-01-01

Abstract This article uses Scale of Change theory as a framework to guide global health researchers to synergistically target women's health outcomes in the context of improving their right to freedom, equity, and equality of opportunities. We hypothesize that health researchers can do so through six action strategies. These strategies include (1) becoming fully informed of women's human rights directives to integrate them into research, (2) mainstreaming gender in the research, (3) using the expertise of grass roots women's organizations in the setting, (4) showcasing women's equity and equality in the organizational infrastructure, (5) disseminating research findings to policymakers in the study locale to influence health priorities, and (6) publicizing the social conditions that are linked to women's diseases. We explore conceptual and logistical dilemmas in transforming a study using these principles and also provide a case study of obstetric fistula reduction in Nigeria to illustrate how these strategies can be operationalized. Our intent is to offer a feasible approach to health researchers who, conceptually, may link women's health to social and cultural conditions but are looking for practical implementation strategies to examine a women's health issue through the lens of their human rights. PMID:20973667

Integrating women's human rights into global health research: an action framework.

PubMed

Baptiste, Donna; Kapungu, Chisina; Khare, Manorama H; Lewis, Yvonne; Barlow-Mosha, Linda

2010-11-01

This article uses Scale of Change theory as a framework to guide global health researchers to synergistically target women's health outcomes in the context of improving their right to freedom, equity, and equality of opportunities. We hypothesize that health researchers can do so through six action strategies. These strategies include (1) becoming fully informed of women's human rights directives to integrate them into research, (2) mainstreaming gender in the research, (3) using the expertise of grass roots women's organizations in the setting, (4) showcasing women's equity and equality in the organizational infrastructure, (5) disseminating research findings to policymakers in the study locale to influence health priorities, and (6) publicizing the social conditions that are linked to women's diseases. We explore conceptual and logistical dilemmas in transforming a study using these principles and also provide a case study of obstetric fistula reduction in Nigeria to illustrate how these strategies can be operationalized. Our intent is to offer a feasible approach to health researchers who, conceptually, may link women's health to social and cultural conditions but are looking for practical implementation strategies to examine a women's health issue through the lens of their human rights.

Engineering Feasibility and Trade Studies for the NASA/VSGC MicroMaps Space Mission

NASA Technical Reports Server (NTRS)

Abdelkhalik, Ossama O.; Nairouz, Bassem; Weaver, Timothy; Newman, Brett

2003-01-01

Knowledge of airborne CO concentrations is critical for accurate scientific prediction of global scale atmospheric behavior. MicroMaps is an existing NASA owned gas filter radiometer instrument designed for space-based measurement of atmospheric CO vertical profiles. Due to programmatic changes, the instrument does not have access to the space environment and is in storage. MicroMaps hardware has significant potential for filling a critical scientific need, thus motivating concept studies for new and innovative scientific spaceflight missions that would leverage the MicroMaps heritage and investment, and contribute to new CO distribution data. This report describes engineering feasibility and trade studies for the NASA/VSGC MicroMaps Space Mission. Conceptual studies encompass: 1) overall mission analysis and synthesis methodology, 2) major subsystem studies and detailed requirements development for an orbital platform option consisting of a small, single purpose spacecraft, 3) assessment of orbital platform option consisting of the International Space Station, and 4) survey of potential launch opportunities for gaining assess to orbit. Investigations are of a preliminary first-order nature. Results and recommendations from these activities are envisioned to support future MicroMaps Mission design decisions regarding program down select options leading to more advanced and mature phases.

Investigation of the feasibility of CARS measurements in scramjet combustion

NASA Technical Reports Server (NTRS)

Shirley, J. A.; Hall, R. J.; Eckbreth, A. C.

1980-01-01

Results are presented of analytical and experimental investigations to determine the feasibility of using coherent anti-Stokes Raman Spectroscopy (CARS) to measure temperature and species concentration in supersonic combustion experiments. The CARS spectra of H2O, O2 and H2 were measured in laboratory flames. Computer code calculated spectra agree very well with the measured spectra. Temperature, and O2 and H2 concentration profiles have been determined from CARS spectra in a laboratory H2 air flat diffusion flame. Temperature measurements agree with radiation corrected thermocouple measurements within 5 to 10 percent, depending on species concentration. The feasibility of measuring O2 concentrations up to 10 percent, from the spectral shape was demonstrated. H2 concentrations determined from CARS intensities agree with spontaneous Raman measurements within a factor of two. Finally, a conceptual design was formulated for diagnostics in the Langley Research Center scramjet combustion facility.

Optimization and conceptual design of demonstration military and civilian mobile satellites using existing buses

NASA Astrophysics Data System (ADS)

Sultan, N.; Payne, W. F.; Carter, D. R.; Jeffrey, G. I.

The Canadian Mobile Satellite (MSAT) program had the objective to demonstrate the feasibility of reliable communications, via a geosynchronous satellite, to a variety of civilian and military users, operating in different frequency bands. The military system would provide, with various degrees of protection against jamming, a variety of military communication services. The civilian mobile satellite system was intended to provide public, mobile radio service (MRS), mobile telephone service (MTS), and data service (DS) to mobile and transportable terminals operating in the 821-825 MHz and 866-870 MHz bands. Service is to be provided for remote data collection platforms. The present investigation is concerned with the feasibility for a military or combined mission using an existing civilian bus, at least for the demonstration phase. It is found that such a use of a civilian bus is indeed feasible.

Evaluating the technical feasibility of aflatoxin risk reduction strategies in Africa.

PubMed

Wu, Felicia; Khlangwiset, Pornsri

2010-05-01

Public health interventions must be readily accepted by their target populations to have any meaningful impact and must have financial and infrastructural support to be feasible in the parts of the world where they are most needed. At the same time, these interventions must be assessed for potential unintended consequences, either to the environment or to human health. In this paper, we evaluate the technical feasibility of interventions to control aflatoxin risk, to be potentially deployed in parts of Africa where aflatoxin exposure poses a significant public health concern. We have applied a conceptual framework for feasibility to four interventions, one associated with each of four different stages of aflatoxin risk: biocontrol (pre-harvest), a post-harvest intervention package (post-harvest), NovaSil clay (dietary), and hepatitis B vaccination (clinical). For each intervention, we have assessed the following four components of technical feasibility: (1) characteristics of the basic intervention, (2) characteristics of delivery, (3) requirements on government capacity, and (4) usage characteristics. We propose ways in which feasibility of each intervention is currently high or low from the perspective of adoption in Africa, how public education is crucial for each of these interventions to succeed, and how to align economic incentives to make the interventions more suitable for less developed countries.

Evaluating the technical feasibility of aflatoxin risk reduction strategies in Africa

PubMed Central

Wu, Felicia; Khlangwiset, Pornsri

2010-01-01

Public health interventions must be readily accepted by their target populations to have any meaningful impact, and must have financial and infrastructural support to be feasible in the parts of the world where they are most needed. At the same time, these interventions must be assessed for potential unintended consequences, either to the environment or to human health. In this paper, we evaluate the technical feasibility of interventions to control aflatoxin risk, to be potentially deployed in parts of Africa where aflatoxin exposure poses a significant public health concern. We have applied a conceptual framework for feasibility to four interventions, one associated with each of four different stages of aflatoxin risk: biocontrol (pre-harvest), a post-harvest intervention package (post-harvest), NovaSil clay (dietary), and hepatitis B vaccination (clinical). For each intervention, we have assessed the following four components of technical feasibility: 1) characteristics of the basic intervention, 2) characteristics of delivery, 3) requirements on government capacity, and 4) usage characteristics. We propose ways in which feasibility of each intervention is currently high or low from the perspective of adoption in Africa, how public education is crucial for each of these interventions to succeed, and how to align economic incentives to make the interventions more suitable for less developed countries. PMID:20455160

Conceptual Design and Cost Estimate of a Subsonic NASA Testbed Vehicle (NTV) for Aeronautics Research

NASA Technical Reports Server (NTRS)

Nickol, Craig L.; Frederic, Peter

2013-01-01

A conceptual design and cost estimate for a subsonic flight research vehicle designed to support NASA's Environmentally Responsible Aviation (ERA) project goals is presented. To investigate the technical and economic feasibility of modifying an existing aircraft, a highly modified Boeing 717 was developed for maturation of technologies supporting the three ERA project goals of reduced fuel burn, noise, and emissions. This modified 717 utilizes midfuselage mounted modern high bypass ratio engines in conjunction with engine exhaust shielding structures to provide a low noise testbed. The testbed also integrates a natural laminar flow wing section and active flow control for the vertical tail. An eight year program plan was created to incrementally modify and test the vehicle, enabling the suite of technology benefits to be isolated and quantified. Based on the conceptual design and programmatic plan for this testbed vehicle, a full cost estimate of $526M was developed, representing then-year dollars at a 50% confidence level.

A climate responsive urban design tool: a platform to improve energy efficiency in a dry hot climate

NASA Astrophysics Data System (ADS)

El Dallal, Norhan; Visser, Florentine

2017-09-01

In the Middle East and North Africa (MENA) region, new urban developments should address the climatic conditions to improve outdoor comfort and to reduce the energy consumption of buildings. This article describes a design tool that supports climate responsive design for a dry hot climate. The approach takes the climate as an initiator for the conceptual urban form with a more energy-efficient urban morphology. The methodology relates the different passive strategies suitable for major climate conditions in MENA region (dry-hot) to design parameters that create the urban form. This parametric design approach is the basis for a tool that generates conceptual climate responsive urban forms so as to assist the urban designer early in the design process. Various conceptual scenarios, generated by a computational model, are the results of the proposed platform. A practical application of the approach is conducted on a New Urban Community in Aswan (Egypt), showing the economic feasibility of the resulting urban form and morphology, and the proposed tool.

Conceptual model of sedimentation in the Sacramento-San Joaquin River Delta

USGS Publications Warehouse

Schoellhamer, David H.; Wright, Scott A.; Drexler, Judith Z.

2012-01-01

Sedimentation in the Sacramento–San Joaquin River Delta builds the Delta landscape, creates benthic and pelagic habitat, and transports sediment-associated contaminants. Here we present a conceptual model of sedimentation that includes submodels for river supply from the watershed to the Delta, regional transport within the Delta and seaward exchange, and local sedimentation in open water and marsh habitats. The model demonstrates feedback loops that affect the Delta ecosystem. Submerged and emergent marsh vegetation act as ecosystem engineers that can create a positive feedback loop by decreasing suspended sediment, increasing water column light, which in turn enables more vegetation. Sea-level rise in open water is partially countered by a negative feedback loop that increases deposition if there is a net decrease in hydrodynamic energy. Manipulation of regional sediment transport is probably the most feasible method to control suspended sediment and thus turbidity. The conceptual model is used to identify information gaps that need to be filled to develop an accurate sediment transport model.

A study of the feasibility of introducing therapeutic touch into the operative environment with patients undergoing cerebral angiography.

PubMed

Madrid, Mary M; Barrett, Elizabeth A M; Winstead-Fry, Patricia

2010-09-01

The purpose of this pilot study was to determine whether Therapeutic Touch (TT) can be effectively used in the operative setting and whether it could produce positive outcomes in the period from cerebral angiography to discharge. The specific outcomes to be assessed were blood pressure, pulse, and respirations. TT is an intervention that involves the intentional direction of energy for the purpose of healing. The present study was developed within the conceptual framework of Rogers's model of unitary human beings. Data were collected at a center for endovascular surgery. The participants were 40 men and women aged between 18 and 80 years who were referred to the center for cerebral angiograms. The participants were English-speaking, ambulatory patients, with no history of prior cerebral angiograms and no psychiatric diagnosis. The design was a randomized, single-blind experiment. The research data were collected in the normal course of the angiogram procedure and recovery room. The blood pressure, pulse, and respirations were routinely noted before, during, and after the procedure. The study was significant in three aspects: (a) it was the first study to develop a protocol for delivering TT in the preoperative course of neurological patients, (b) the study is conceptualized within Rogers's conceptual model of unitary human beings, and (c) the study explored the impact of TT on selected outcomes in endovascular patients. A protocol for delivering TT in the operative setting was successfully developed and implemented. The efficacy of TT on the blood pressure, respirations, and pulse of the experimental group was not statistically significant. The reasons for this finding are explored, and suggestions are made for future research.

Hydrogen turbine power conversion system assessment

NASA Technical Reports Server (NTRS)

Wright, D. E.; Lucci, A. D.; Campbell, J.; Lee, J. C.

1978-01-01

A three part technical study was conducted whereby parametric technical and economic feasibility data were developed on several power conversion systems suitable for the generation of central station electric power through the combustion of hydrogen and the use of the resulting heat energy in turbogenerator equipment. The study assessed potential applications of hydrogen-fueled power conversion systems and identified the three most promising candidates: (1) Ericsson Cycle, (2) gas turbine, and (3) direct steam injection system for fossil fuel as well as nuclear powerplants. A technical and economic evaluation was performed on the three systems from which the direct injection system (fossil fuel only) was selected for a preliminary conceptual design of an integrated hydrogen-fired power conversion system.

Magnetohydrodynamics (MHD) Engineering Test Facility (ETF) 200 MWe power plant. Conceptual Design Engineering Report (CDER). Volume 4: Supplementary engineering data

NASA Astrophysics Data System (ADS)

1981-09-01

The reference conceptual design of the Magnetohydrodynamic Engineering Test Facility (ETF), a prototype 200 MWe coal-fired electric generating plant designed to demonstrate the commercial feasibility of open cycle MHD is summarized. Main elements of the design are identified and explained, and the rationale behind them is reviewed. Major systems and plant facilities are listed and discussed. Construction cost and schedule estimates, and identification of engineering issues that should be reexamined are also given. The latest (1980-1981) information from the MHD technology program are integrated with the elements of a conventional steam power electric generating plant. Supplementary Engineering Data (Issues, Background, Performance Assurance Plan, Design Details, System Design Descriptions and Related Drawings) is presented.

Magnetohydrodynamics (MHD) Engineering Test Facility (ETF) 200 MWe power plant. Conceptual Design Engineering Report (CDER). Volume 4: Supplementary engineering data

NASA Technical Reports Server (NTRS)

1981-01-01

The reference conceptual design of the Magnetohydrodynamic Engineering Test Facility (ETF), a prototype 200 MWe coal-fired electric generating plant designed to demonstrate the commercial feasibility of open cycle MHD is summarized. Main elements of the design are identified and explained, and the rationale behind them is reviewed. Major systems and plant facilities are listed and discussed. Construction cost and schedule estimates, and identification of engineering issues that should be reexamined are also given. The latest (1980-1981) information from the MHD technology program are integrated with the elements of a conventional steam power electric generating plant. Supplementary Engineering Data (Issues, Background, Performance Assurance Plan, Design Details, System Design Descriptions and Related Drawings) is presented.

Explosive propulsion applications. [to future unmanned missions

NASA Technical Reports Server (NTRS)

Nakamura, Y.; Varsi, G.; Back, L. H.

1974-01-01

The feasibility and application of an explosive propulsion concept capable of supporting future unmanned missions in the post-1980 era were examined and recommendations made for advanced technology development tasks. The Venus large lander mission was selected as the first in which the explosive propulsion concept can find application. A conceptual design was generated and its performance, weight, costs, and interaction effects determined. Comparisons were made with conventional propulsion alternatives. The feasibility of the explosive propulsion system was verified for planetology experiments within the dense atmosphere of Venus as well as the outer planets. Additionally, it was determined that the Venus large lander mission could be augmented ballistically with a significant delivery margin.

Feasibility and acceptability of the DSM-5 Field Trial procedures in the Johns Hopkins Community Psychiatry Programs†

PubMed Central

Clarke, Diana E.; Wilcox, Holly C.; Miller, Leslie; Cullen, Bernadette; Gerring, Joan; Greiner, Lisa H.; Newcomer, Alison; Mckitty, Mellisha V.; Regier, Darrel A.; Narrow, William E.

2014-01-01

The Diagnostic and Statistical Manual of Mental Disorders, Fifth Edition (DSM-5) contains criteria for psychiatric diagnoses that reflect advances in the science and conceptualization of mental disorders and address the needs of clinicians. DSM-5 also recommends research on dimensional measures of cross-cutting symptoms and diagnostic severity, which are expected to better capture patients’ experiences with mental disorders. Prior to its May 2013 release, the American Psychiatric Association (APA) conducted field trials to examine the feasibility, clinical utility, reliability, and where possible, the validity of proposed DSM-5 diagnostic criteria and dimensional measures. The methods and measures proposed for the DSM-5 field trials were pilot tested in adult and child/adolescent clinical samples, with the goal to identify and correct design and procedural problems with the proposed methods before resources were expended for the larger DSM-5 Field Trials. Results allowed for the refinement of the protocols, procedures, and measures, which facilitated recruitment, implementation, and completion of the DSM-5 Field Trials. These results highlight the benefits of pilot studies in planning large multisite studies. PMID:24615761

CARS temperature measurements in the fuel preburner of the Space Shuttle main engine: A feasibility study

NASA Technical Reports Server (NTRS)

Beiting, E. J.; Luthe, J. C.

1983-01-01

This report discusses the feasibility of making temperature profile measurements in the fuel preburner of the main engine of the space shuttle (SSME) using coherent anti-Stokes Raman spectroscopy (CARS). The principal thrust of the work is to identify problems associated with making CARS measurements in high temperature gas phase hydrogen at very high pressures (approx 400 atmospheres). To this end a theoretical study was made of the characteristics of the CAR spectra of H2 as a function of temperature and pressure and the accuracy with which temperatures can be extracted from this spectra. In addition the experimental problems associated with carrying out these measurements on a SSME at NSTL were identified. A conceptual design of a CARS system suitable for this work is included. Many of the results of the calculations made in this report are plotted as a function of temperature. In the course of presenting these results, it was necessary to decide whether the number of density or the pressure should be treated as a fixed parameter.

The feasibility of solar reflector production from lunar materials for solar power in space

NASA Technical Reports Server (NTRS)

1990-01-01

Science Applications International Corporation (SAIC) investigated the feasibility of producing solar reflectors from indigenous lunar materials for solar power production on the moon. First, lunar construction materials and production processes were reviewed, and candidate materials for reflector production were identified. At the same time, lunar environmental conditions were reviewed for their effect on production of concentrators. Next, conceptual designs and fabrication methods were proposed and studied for production of dish concentrators and heliostats. Finally, fabrication testing was performed on small-scale models using earth analogs of lunar materials. Findings from this initial investigation indicate that production of concentrators from lunar materials may be an attractive approach for solar energy production on the moon. Further design and testing are required to determine the best techniques and approaches to optimize this concept. Four materials were identified as having high potential for solar reflector manufacture. These baseline materials were foamed glass, concrete with glass-fiber reinforcement, a glass-fiber/glass-melt composite, and an iron-glass sintered material.

Feasibility demonstration for electroplating ultra-thin polyimide film. [fabricating film for space erectable structures

NASA Technical Reports Server (NTRS)

Schneier, R.; Braswell, T. V.; Vaughn, R. W.

1978-01-01

The effect of electrodeposition variables on film thickness was investigated using a dilute polyimide solution as a bath into which aluminum (as foil or as a vapor deposited coating) was immersed. The electrodeposited film was dried for 2 hours at 93 C (primarily to remove solvent) and cured for 18 hours at 186 C. Infrared studies indicate that imide formation (curing) occurs at 149 C under vacuum. From a conceptual viewpoint, satisfactory film metallized on one side can be obtained by this method. The cured ultra thin polyimide film exhibits properties equivalent to those of commercial film, and the surface appearance of the strippable polyimide film compares favorably with that of a sample of commercial film of thicker gauge. The feasibility of manufacturing approximately one million sq m of ultra thin film capable of being joined to fabricate an 800 m by 9 800 m square from starting material 0.5 to 1 m wide for space erectable structures was demonstrated.

Initial planetary base construction techniques and machine implementation

NASA Technical Reports Server (NTRS)

Crockford, William W.

1987-01-01

Conceptual designs of (1) initial planetary base structures, and (2) an unmanned machine to perform the construction of these structures using materials local to the planet are presented. Rock melting is suggested as a possible technique to be used by the machine in fabricating roads, platforms, and interlocking bricks. Identification of problem areas in machine design and materials processing is accomplished. The feasibility of the designs is contingent upon favorable results of an analysis of the engineering behavior of the product materials. The analysis requires knowledge of several parameters for solution of the constitutive equations of the theory of elasticity. An initial collection of these parameters is presented which helps to define research needed to perform a realistic feasibility study. A qualitative approach to estimating power and mass lift requirements for the proposed machine is used which employs specifications of currently available equipment. An initial, unmanned mission scenario is discussed with emphasis on identifying uncompleted tasks and suggesting design considerations for vehicles and primitive structures which use the products of the machine processing.

Design concepts for a composite door frame system for general automotive applications

NASA Technical Reports Server (NTRS)

Tauber, J. A.

1976-01-01

Conceptual design, manufacturing process, and costs are explored to determine the feasibility of replacing present steel parts in automotive door structures with various composite materials. The problems of conforming to present anti-intrusion specifications with advanced materials are examined and discussed. Modest weight reductions, at competitive costs, were identified for the utilization of specific composite materials in automotive door structures.

Examining the Feasibility of Smartphone Game Applications for Physical Activity Promotion in Middle School Students.

PubMed

Blackman, Kacie C A; Zoellner, Jamie; Kadir, Adil; Dockery, Brandon; Johnson, Sallie Beth; Almeida, Fabio A; McCrickard, D Scott; Hill, Jennie L; You, Wen; Estabrooks, Paul A

2015-10-01

The objective of this study was to determine the feasibility (i.e., limited efficacy testing, practicality, and acceptability) of a 6-week smartphone game-based applications program for promoting physical activity (PA) in adolescents in an afterschool program. This mixed-method, quasi-experimental design study included 27 adolescents who evaluated four smartphone PA game-based applications in two Boys & Girls Clubs of America. After an initial baseline week (i.e., usual activity during their visit to the Club), adolescents played each game for 1 week. During a final week, the participants could choose to play any combination of the four games. An established conceptual framework was used to assess feasibility. Efficacy was assessed by changes in PA via wrist-worn accelerometers (model GT3x+; ActiGraph LLC, Pensacola, FL). Practicality was measured through field notes, the number of players attending each session, and the proportion of attendees who played the games. Acceptability was measured using poststudy focus groups. Compared with baseline (3.22 metabolic equivalents [METs]), mean accelerometer values were significantly (P<0.05) higher during "Space Rayders" (4.33 METs) and "Color Hunt" (3.67 METs). Attendance did not differ among games, and weekly number of players averaged 12 of 27 participants. Qualitative findings indicated that participants perceived "Space Rayders" as the most acceptable game. Overall, participants found the games to be enjoyable and easy to use, although they had suggestions to improve graphics and sounds. Smartphone games can be feasible for adolescents to use for PA. Lessons learned will be used to provide improvements for future game development and evaluation.

Feasibility and Acceptability of a Colocated Homeless-Tailored Primary Care Clinic and Emergency Department.

PubMed

Gabrielian, Sonya; Chen, Jennifer C; Minhaj, Beena P; Manchanda, Rishi; Altman, Lisa; Koosis, Ella; Gelberg, Lillian

2017-10-01

Homeless adults have low primary care engagement and high emergency department (ED) utilization. Homeless-tailored, patient-centered medical homes (PCMH) decrease this population's acute care use. We studied the feasibility (focused on patient recruitment) and acceptability (conceptualized as clinicians' attitudes/beliefs) of a pilot initiative to colocate a homeless-tailored PCMH with an ED. After ED triage, low-acuity patients appropriate for outpatient care were screened for homelessness; homeless patients chose between a colocated PCMH or ED visit. To study feasibility, we captured (from May to September 2012) the number of patients screened for homelessness, positive screens, unique patients seen, and primary care visits. We focused on acceptability to ED clinicians (physicians, nurses, social workers); we sent a 32-item survey to ED clinicians (n = 57) who worked during clinic hours. Questions derived from an instrument measuring clinician attitudes toward homeless persons; acceptability of homelessness screening and the clinic itself were also explored. Over the 5 months of interest, 281 patients were screened; 172 (61.2%) screened positive for homelessness; 112 (65.1%) of these positive screens were seen over 215 visits. Acceptability data were obtained from 56% (n = 32) of surveyed clinicians. Attitudes toward homeless patients were similar to prior studies of primary care physicians. Most (54.6%) clinicians agreed with the homelessness screening procedures. Nearly all (90.3%) clinicians supported expansion of the homeless-tailored clinic; a minority (42.0%) agreed that ED colocation worked well. Our data suggest the feasibility of recruiting patients to a homeless-tailored primary care clinic colocated with the ED; however, the clinic's acceptability was mixed. Future quality improvement work should focus on tailoring the clinic to increase its acceptability among ED clinicians, while assessing its impact on health, housing, and costs.

Feasibility and Acceptability of a Colocated Homeless-Tailored Primary Care Clinic and Emergency Department

PubMed Central

Gabrielian, Sonya; Chen, Jennifer C.; Minhaj, Beena P.; Manchanda, Rishi; Altman, Lisa; Koosis, Ella; Gelberg, Lillian

2017-01-01

Objectives: Homeless adults have low primary care engagement and high emergency department (ED) utilization. Homeless-tailored, patient-centered medical homes (PCMH) decrease this population’s acute care use. We studied the feasibility (focused on patient recruitment) and acceptability (conceptualized as clinicians’ attitudes/beliefs) of a pilot initiative to colocate a homeless-tailored PCMH with an ED. After ED triage, low-acuity patients appropriate for outpatient care were screened for homelessness; homeless patients chose between a colocated PCMH or ED visit. Methods: To study feasibility, we captured (from May to September 2012) the number of patients screened for homelessness, positive screens, unique patients seen, and primary care visits. We focused on acceptability to ED clinicians (physicians, nurses, social workers); we sent a 32-item survey to ED clinicians (n = 57) who worked during clinic hours. Questions derived from an instrument measuring clinician attitudes toward homeless persons; acceptability of homelessness screening and the clinic itself were also explored. Results: Over the 5 months of interest, 281 patients were screened; 172 (61.2%) screened positive for homelessness; 112 (65.1%) of these positive screens were seen over 215 visits. Acceptability data were obtained from 56% (n = 32) of surveyed clinicians. Attitudes toward homeless patients were similar to prior studies of primary care physicians. Most (54.6%) clinicians agreed with the homelessness screening procedures. Nearly all (90.3%) clinicians supported expansion of the homeless-tailored clinic; a minority (42.0%) agreed that ED colocation worked well. Conclusion: Our data suggest the feasibility of recruiting patients to a homeless-tailored primary care clinic colocated with the ED; however, the clinic’s acceptability was mixed. Future quality improvement work should focus on tailoring the clinic to increase its acceptability among ED clinicians, while assessing its impact on health, housing, and costs. PMID:28367682

Semantic web for integrated network analysis in biomedicine.

PubMed

Chen, Huajun; Ding, Li; Wu, Zhaohui; Yu, Tong; Dhanapalan, Lavanya; Chen, Jake Y

2009-03-01

The Semantic Web technology enables integration of heterogeneous data on the World Wide Web by making the semantics of data explicit through formal ontologies. In this article, we survey the feasibility and state of the art of utilizing the Semantic Web technology to represent, integrate and analyze the knowledge in various biomedical networks. We introduce a new conceptual framework, semantic graph mining, to enable researchers to integrate graph mining with ontology reasoning in network data analysis. Through four case studies, we demonstrate how semantic graph mining can be applied to the analysis of disease-causal genes, Gene Ontology category cross-talks, drug efficacy analysis and herb-drug interactions analysis.

A study of a space communication system for the control and monitoring of the electric distribution system. Volume 1: Summary

NASA Technical Reports Server (NTRS)

Vaisnys, A.

1980-01-01

It is technically feasible to design a satellite communication system to serve the United States electric utility industry's needs relative to load management, real-time operations management, remote meter reading, and to determine the costs of various elements of the system. A definition of distribution control and monitoring functions is given. Associated communications traffic is quantified. A baseline conceptual design in terms of operating capability and equipment is described, important factors to be considered in designing a system are examined, and preliminary cost data are provided. Factors associated with implementation are discussed and conclusions and recommendations are listed.

Conceptual design study of the moderate size superconducting spherical tokamak power plant

NASA Astrophysics Data System (ADS)

Gi, Keii; Ono, Yasushi; Nakamura, Makoto; Someya, Youji; Utoh, Hiroyasu; Tobita, Kenji; Ono, Masayuki

2015-06-01

A new conceptual design of the superconducting spherical tokamak (ST) power plant was proposed as an attractive choice for tokamak fusion reactors. We reassessed a possibility of the ST as a power plant using the conservative reactor engineering constraints often used for the conventional tokamak reactor design. An extensive parameters scan which covers all ranges of feasible superconducting ST reactors was completed, and five constraints which include already achieved plasma magnetohydrodynamic (MHD) and confinement parameters in ST experiments were established for the purpose of choosing the optimum operation point. Based on comparison with the estimated future energy costs of electricity (COEs) in Japan, cost-effective ST reactors can be designed if their COEs are smaller than 120 mills kW-1 h-1 (2013). We selected the optimized design point: A = 2.0 and Rp = 5.4 m after considering the maintenance scheme and TF ripple. A self-consistent free-boundary MHD equilibrium and poloidal field coil configuration of the ST reactor were designed by modifying the neutral beam injection system and plasma profiles. The MHD stability of the equilibrium was analysed and a ramp-up scenario was considered for ensuring the new ST design. The optimized moderate-size ST power plant conceptual design realizes realistic plasma and fusion engineering parameters keeping its economic competitiveness against existing energy sources in Japan.

Modifiers of Neighbors' Bystander Intervention in Intimate Partner Violence: A Concept Mapping Study.

PubMed

Wee, Sara; Todd, Mary-Justine; Oshiro, Michael; Greene, Emily; Frye, Victoria

2016-03-01

Encouraging bystander intervention in intimate partner violence (IPV) against women is potentially an important method of reducing the prevalence of such violence in urban communities. Most existing research has been conducted on campuses and in relation to sexual violence among teens or young adults. Our understanding of which bystander behaviors are feasible is nascent, and our knowledge of which situational factors influence neighbors' self-reported willingness to intervene is underdeveloped. We conducted a concept mapping study to identify potential bystander intervention behaviors in IPV among neighbors in urban settings; we also assessed whether perceived feasibility and effectiveness of those behaviors varied by situational characteristics. Using data collected from 41 residents of a low-income New York City neighborhood in late 2011, concept mapping was used to create a conceptual map of the 74 behaviors identified by participants. We examined participant differences in mean feasibility (i.e., that the participants "could" or "would" enact a behavior), feasibility given two situational characteristics (if the couple was perceived to have a history of IPV, and if children were believed to be involved or present), and perceived effectiveness of bystander behaviors. Differences across select sociodemographic factors of participants were also analyzed. A 13-cluster solution emerged, with clusters of bystander behaviors grouped into four larger cluster areas: victim focused, parenting/education focused, perpetrator focused, and community involvement focused. Bivariate analyses revealed that participants rated the four cluster areas as more feasible when a child was believed to be involved. Male participants rated intervention as less feasible when the couple was believed to have a history of IPV. Participants who reported a history of IPV victimization rated all four cluster areas as less effective on average, as compared with participants without a history of IPV. This study explored bystander intervention into IPV outside of a college context and among urban adults living in high-poverty areas. Results suggest that the presence of children and perceived history of IPV may affect bystander intervention. Specific recommendations to build the research base on bystander intervention in adult IPV as well as what situational, sociodemographic, and other factors mitigate against intervention among potential responders are offered.

Space tether dynamics: an introduction

NASA Astrophysics Data System (ADS)

Denny, Mark

2018-05-01

The dynamics of orbiting tethers (space elevators and skyhooks) is developed from an unusual direction: Lagrangian rather than Newtonian mechanics. These basic results are derived among others: space elevator required length with and without counterweight, location and magnitude of maximum tether tension, skyhook orbital parameters and tether tension. These conceptual devices are being increasingly discussed as technologically feasible; here they make an interesting pedagogical application of Lagrangian mechanics suitable for undergraduate physics students.

Pre- and posttreatment techniques for spacecraft water recovery

NASA Technical Reports Server (NTRS)

Putnam, David F.; Colombo, Gerald V.; Michalek, William F.

1987-01-01

The objective was to develop techniques for satisfactory pretreatment of waste water (urine and wash water) prior to recovery by distillation and satisfactory post-treatment of the recovered water and humidity condensate for purification to the high quality necessary for reuse. The effort included literature and laboratory investigations, feasibility evaluations of candidate approaches, and development of conceptual designs for a waste water pretreatment system and a recovered water post-treatment system.

Conceptual design and feasibility evaluation model of a 10 to the 8th power bit oligatomic mass memory. Volume 1: Conceptual design

NASA Technical Reports Server (NTRS)

Recksiedler, A. L.; Lutes, C. L.

1972-01-01

The oligatomic (mirror) thin film memory technology is a suitable candidate for general purpose spaceborne applications in the post-1975 time frame. Capacities of around 10 to the 8th power bits can be reliably implemented with systems designed around a 335 million bit module. The recommended mode was determined following an investigation of implementation sizes ranging from an 8,000,000 to 100,000,000 bits per module. Cost, power, weight, volume, reliability, maintainability and speed were investigated. The memory includes random access, NDRO, SEC-DED, nonvolatility, and dual interface characteristics. The applications most suitable for the technology are those involving a large capacity with high speed (no latency), nonvolatility, and random accessing.

A process model of technology innovation in governmental agencies: Insights from NASA’s science directorate

NASA Astrophysics Data System (ADS)

Szajnfarber, Zoe; Weigel, Annalisa L.

2013-03-01

This paper investigates the process through which new technical concepts are matured in the NASA innovation ecosystem. We propose an "epoch-shock" conceptualization as an alternative mental model to the traditional stage-gate view. The epoch-shock model is developed inductively, based on detailed empirical observations of the process, and validated, to the extent possible, through expert review. The paper concludes by illustrating how the new epoch-shock conceptualization could provide a useful basis for rethinking feasible interventions to improve innovation management in the space agency context. Where the more traditional stage-gate model leads to an emphasis on centralized flow control, the epoch-shock model acknowledges the decentralized, probabilistic nature of key interactions and highlights which aspects may be influenced.

Preliminary conceptual design for geothermal space heating conversion of school district 50 joint facilities at Pagosa Springs, Colorado. GTA report no. 6

NASA Astrophysics Data System (ADS)

Engen, I. A.

1981-11-01

This feasibility study and preliminary conceptual design effect assesses the conversion of a high school and gym, and a middle school building to geothermal space heating is assessed. A preliminary cost benefit assessment made on the basis of estimated costs for conversion, system maintenance, debt service, resource development, electricity to power pumps, and savings from from reduced natural gas consumption concluded that an economic conversion depended on development of an adequate geothermal resource (approximately 1500F, 400 gpm). Material selection assumed that the geothermal water to the main supply system was isolated to minimize effects of corrosion and deposition, and that system compatible components are used for the building modifications. Asbestos cement distribution pipe, a stainless steel heat exchanger, and stainless steel lined valves were recommended for the supply, heat transfer, and disposal mechanisms, respectively. A comparison of the calculated average gas consumption cost, escalated at 10% per year, with conversion project cost, both in 1977 dollars, showed that the project could be amortized over less than 20 years at current interest rates.

Permutation Tests of Hierarchical Cluster Analyses of Carrion Communities and Their Potential Use in Forensic Entomology.

PubMed

van der Ham, Joris L

2016-05-19

Forensic entomologists can use carrion communities' ecological succession data to estimate the postmortem interval (PMI). Permutation tests of hierarchical cluster analyses of these data provide a conceptual method to estimate part of the PMI, the post-colonization interval (post-CI). This multivariate approach produces a baseline of statistically distinct clusters that reflect changes in the carrion community composition during the decomposition process. Carrion community samples of unknown post-CIs are compared with these baseline clusters to estimate the post-CI. In this short communication, I use data from previously published studies to demonstrate the conceptual feasibility of this multivariate approach. Analyses of these data produce series of significantly distinct clusters, which represent carrion communities during 1- to 20-day periods of the decomposition process. For 33 carrion community samples, collected over an 11-day period, this approach correctly estimated the post-CI within an average range of 3.1 days. © The Authors 2016. Published by Oxford University Press on behalf of Entomological Society of America. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Systematic searching for theory to inform systematic reviews: is it feasible? Is it desirable?

PubMed

Booth, Andrew; Carroll, Christopher

2015-09-01

In recognising the potential value of theory in understanding how interventions work comes a challenge - how to make identification of theory less haphazard? To explore the feasibility of systematic identification of theory. We searched PubMed for published reviews (1998-2012) that had explicitly sought to identify theory. Systematic searching may be characterised by a structured question, methodological filters and an itemised search procedure. We constructed a template (BeHEMoTh - Behaviour of interest; Health context; Exclusions; Models or Theories) for use when systematically identifying theory. The authors tested the template within two systematic reviews. Of 34 systematic reviews, only 12 reviews (35%) reported a method for identifying theory. Nineteen did not specify how they identified studies containing theory. Data were unavailable for three reviews. Candidate terms include concept(s)/conceptual, framework(s), model(s), and theory/theories/theoretical. Information professionals must overcome inadequate reporting and the use of theory out of context. The review team faces an additional concern in lack of 'theory fidelity'. Based on experience with two systematic reviews, the BeHEMoTh template and procedure offers a feasible and useful approach for identification of theory. Applications include realist synthesis, framework synthesis or review of complex interventions. The procedure requires rigorous evaluation. © 2015 Health Libraries Group.

Acquiring Science and Social Studies Knowledge in Kindergarten Through Fourth Grade: Conceptualization, Design, Implementation, and Efficacy Testing of Content-Area Literacy Instruction (CALI)

PubMed Central

Dombek, Jennifer; Crowe, Elizabeth C.; Spencer, Mercedes; Tighe, Elizabeth L.; Coffinger, Sean; Zargar, Elham; Wood, Taffeta; Petscher, Yaacov

2016-01-01

With national focus on reading and math achievement, science and social studies have received less instructional time. Yet, accumulating evidence suggests that content knowledge is an important predictor of proficient reading. Starting with a design study, we developed Content Area Literacy Instruction (CALI), as an individualized (or personalized) instructional program for kindergarteners through fourth graders to build science and social studies knowledge. We developed CALI to be implemented in general education classrooms, over multiple iterations (n=230 students), using principles of design-based implementation research. The aims were to develop CALI as a usable and feasible instructional program that would, potentially, improve science and social studies knowledge, and could be implemented during the literacy block without negatively affecting students' reading gains (i.e., no opportunity cost). We then evaluated the efficacy of CALI in a randomized controlled field trial with 418 students in kindergarten through fourth grade. Results reveal that CALI demonstrates promise as a useable and feasible instructional individualized general education program, and is efficacious in improving social studies (d=2.2) and science (d=2.1) knowledge, with some evidence of improving oral and reading comprehension skills (d=.125). PMID:28479610

Energy utilization: municipal waste incineration. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

LaBeck, M.F.

An assessment is made of the technical and economical feasibility of converting municipal waste into useful and useable energy. The concept presented involves retrofitting an existing municipal incinerator with the systems and equipment necessary to produce process steam and electric power. The concept is economically attractive since the cost of necessary waste heat recovery equipment is usually a comparatively small percentage of the cost of the original incinerator installation. Technical data obtained from presently operating incinerators designed specifically for generating energy, documents the technical feasibility and stipulates certain design constraints. The investigation includes a cost summary; description of process andmore » facilities; conceptual design; economic analysis; derivation of costs; itemized estimated costs; design and construction schedule; and some drawings.« less

Deep Borehole Field Test Conceptual Design Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hardin, Ernest L.

This report documents conceptual design development for the Deep Borehole Field Test (DBFT), including test packages (simulated waste packages, not containing waste) and a system for demonstrating emplacement and retrieval of those packages in the planned Field Test Borehole (FTB). For the DBFT to have demonstration value, it must be based on conceptualization of a deep borehole disposal (DBD) system. This document therefore identifies key options for a DBD system, describes an updated reference DBD concept, and derives a recommended concept for the DBFT demonstration. The objective of the DBFT is to confirm the safety and feasibility of the DBDmore » concept for long-term isolation of radioactive waste. The conceptual design described in this report will demonstrate equipment and operations for safe waste handling and downhole emplacement of test packages, while contributing to an evaluation of the overall safety and practicality of the DBD concept. The DBFT also includes drilling and downhole characterization investigations that are described elsewhere (see Section 1). Importantly, no radioactive waste will be used in the DBFT, nor will the DBFT site be used for disposal of any type of waste. The foremost performance objective for conduct of the DBFT is to demonstrate safe operations in all aspects of the test.« less

Detonation wave augmentation of gas turbines

NASA Technical Reports Server (NTRS)

Wortman, A.

1984-01-01

The results of a feasibility study that examined the effects of using detonation waves to augment the performance of gas turbines are reported. The central ideas were to reduce compressor requirements and to maintain high performance in jet engines. Gasdynamic equations were used to model the flows associated with shock waves generated by the detonation of fuel in detonator tubes. Shock wave attenuation to the level of Mach waves was found possible, thus eliminating interference with the compressor and the necessity of valves and seals. A preliminary parametric study of the performance of a compressor working at a 4:1 ratio in a conceptual design of a detonation wave augmented jet engine in subsonic flight indicated a clear superiority over conventional designs in terms of fuel efficiency and thrust.

Conceptual model for dietary behaviour change at household level: a 'best-fit' qualitative study using primary data.

PubMed

Daivadanam, Meena; Wahlström, Rolf; Ravindran, T K Sundari; Thankappan, K R; Ramanathan, Mala

2014-06-09

Interventions having a strong theoretical basis are more efficacious, providing a strong argument for incorporating theory into intervention planning. The objective of this study was to develop a conceptual model to facilitate the planning of dietary intervention strategies at the household level in rural Kerala. Three focus group discussions and 17 individual interviews were conducted among men and women, aged between 23 and 75 years. An interview guide facilitated the process to understand: 1) feasibility and acceptability of a proposed dietary behaviour change intervention; 2) beliefs about foods, particularly fruits and vegetables; 3) decision-making in households with reference to food choices and access; and 4) to gain insights into the kind of intervention strategies that may be practical at community and household level. The data were analysed using a modified form of qualitative framework analysis, which combined both deductive and inductive reasoning. A priori themes were identified from relevant behaviour change theories using construct definitions, and used to index the meaning units identified from the primary qualitative data. In addition, new themes emerging from the data were included. The associations between the themes were mapped into four main factors and its components, which contributed to construction of the conceptual model. Thirteen of the a priori themes from three behaviour change theories (Trans-theoretical model, Health Belief model and Theory of Planned Behaviour) were confirmed or slightly modified, while four new themes emerged from the data. The conceptual model had four main factors and its components: impact factors (decisional balance, risk perception, attitude); change processes (action-oriented, cognitive); background factors (personal modifiers, societal norms); and overarching factors (accessibility, perceived needs and preferences), built around a three-stage change spiral (pre-contemplation, intention, action). Decisional balance was the strongest in terms of impacting the process of behaviour change, while household efficacy and perceived household cooperation were identified as 'markers' for stages-of-change at the household level. This type of framework analysis made it possible to develop a conceptual model that could facilitate the design of intervention strategies to aid a household-level dietary behaviour change process.

Conceptual model for dietary behaviour change at household level: a ‘best-fit’ qualitative study using primary data

PubMed Central

2014-01-01

Background Interventions having a strong theoretical basis are more efficacious, providing a strong argument for incorporating theory into intervention planning. The objective of this study was to develop a conceptual model to facilitate the planning of dietary intervention strategies at the household level in rural Kerala. Methods Three focus group discussions and 17 individual interviews were conducted among men and women, aged between 23 and 75 years. An interview guide facilitated the process to understand: 1) feasibility and acceptability of a proposed dietary behaviour change intervention; 2) beliefs about foods, particularly fruits and vegetables; 3) decision-making in households with reference to food choices and access; and 4) to gain insights into the kind of intervention strategies that may be practical at community and household level. The data were analysed using a modified form of qualitative framework analysis, which combined both deductive and inductive reasoning. A priori themes were identified from relevant behaviour change theories using construct definitions, and used to index the meaning units identified from the primary qualitative data. In addition, new themes emerging from the data were included. The associations between the themes were mapped into four main factors and its components, which contributed to construction of the conceptual model. Results Thirteen of the a priori themes from three behaviour change theories (Trans-theoretical model, Health Belief model and Theory of Planned Behaviour) were confirmed or slightly modified, while four new themes emerged from the data. The conceptual model had four main factors and its components: impact factors (decisional balance, risk perception, attitude); change processes (action-oriented, cognitive); background factors (personal modifiers, societal norms); and overarching factors (accessibility, perceived needs and preferences), built around a three-stage change spiral (pre-contemplation, intention, action). Decisional balance was the strongest in terms of impacting the process of behaviour change, while household efficacy and perceived household cooperation were identified as ‘markers’ for stages-of-change at the household level. Conclusions This type of framework analysis made it possible to develop a conceptual model that could facilitate the design of intervention strategies to aid a household-level dietary behaviour change process. PMID:24912496

1170 MW/sub t/ HTGR steamer cogeneration plant: design and cost study

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

A conceptual design and cost study is presented for intermediate size high temperature gas-cooled reactor (HTGR) for industrial energy applications performed by United Engineers and Constructors Inc., (UE and C) and The General Atomic Company (GAC). The study is part of a program at ORNL and has the objective to provide support in the evaluation of the technical and economic feasibility of a single unit 1170 MW/sub t/ HTGR steam cycle cogeneration plant (referred to as the Steamer plant) for the production of industrial process energy. Inherent in the achievement of this objective, it was essential to perform a numbermore » of basic tasks such as the development of plant concept, capital cost estimate, project schedule and annual operation and maintenance (O and M) cost.« less

Steps in the design, development and formative evaluation of obesity prevention-related behavior change trials.

PubMed

Baranowski, Tom; Cerin, Ester; Baranowski, Janice

2009-01-21

Obesity prevention interventions through dietary and physical activity change have generally not been effective. Limitations on possible program effectiveness are herein identified at every step in the mediating variable model, a generic conceptual framework for understanding how interventions may promote behavior change. To minimize these problems, and thereby enhance likely intervention effectiveness, four sequential types of formative studies are proposed: targeted behavior validation, targeted mediator validation, intervention procedure validation, and pilot feasibility intervention. Implementing these studies would establish the relationships at each step in the mediating variable model, thereby maximizing the likelihood that an intervention would work and its effects would be detected. Building consensus among researchers, funding agencies, and journal editors on distinct intervention development studies should avoid identified limitations and move the field forward.

Steps in the design, development and formative evaluation of obesity prevention-related behavior change trials

PubMed Central

Baranowski, Tom; Cerin, Ester; Baranowski, Janice

2009-01-01

Obesity prevention interventions through dietary and physical activity change have generally not been effective. Limitations on possible program effectiveness are herein identified at every step in the mediating variable model, a generic conceptual framework for understanding how interventions may promote behavior change. To minimize these problems, and thereby enhance likely intervention effectiveness, four sequential types of formative studies are proposed: targeted behavior validation, targeted mediator validation, intervention procedure validation, and pilot feasibility intervention. Implementing these studies would establish the relationships at each step in the mediating variable model, thereby maximizing the likelihood that an intervention would work and its effects would be detected. Building consensus among researchers, funding agencies, and journal editors on distinct intervention development studies should avoid identified limitations and move the field forward. PMID:19159476

MIUS community conceptual design study

NASA Technical Reports Server (NTRS)

Fulbright, B. E.

1976-01-01

The feasibility, practicality, and applicability of the modular integrated utility systems (MIUS) concept to a satellite new-community development with a population of approximately 100,000 were analyzed. Two MIUS design options, the 29-MIUS-unit (option 1) and the 8-MIUS-unit (option 2) facilities were considered. Each resulted in considerable resource savings when compared to a conventional utility system. Economic analyses indicated that the total cash outlay and operations and maintenance costs for these two options were considerably less than for a conventional system. Computer analyses performed in support of this study provided corroborative data for the study group. An environmental impact assessment was performed to determine whether the MIUS meets or will meet necessary environmental standards. The MIUS can provide improved efficiency in the conservation of natural resources while not adversely affecting the physical environment.

A Hypothesis: Life Initiated from Two Genes, as Deduced from the RNA World Hypothesis and the Characteristics of Life-Like Systems

PubMed Central

Kawamura, Kunio

2016-01-01

RNA played a central role in the emergence of the first life-like system on primitive Earth since RNA molecules contain both genetic information and catalytic activity. However, there are several drawbacks regarding the RNA world hypothesis. Here, I briefly discuss the feasibility of the RNA world hypothesis to deduce the RNA functions that are essential for forming a life-like system. At the same time, I have conducted a conceptual analysis of the characteristics of biosystems as a useful approach to deduce a realistic life-like system in relation to the definition of life. For instance, an RNA-based life-like system should possess enough stability to resist environmental perturbations, by developing a cell-like compartment, for instance. Here, a conceptual viewpoint is summarized to provide a realistic life-like system that is compatible with the primitive Earth environment and the capabilities of RNA molecules. According to the empirical and conceptual analysis, I propose the hypothesis that the first life-like system could have initiated from only two genes. PMID:27490571

Conceptual design of a fleet of autonomous regolith throwing devices for radiation shielding of lunar habitats

NASA Technical Reports Server (NTRS)

Armstrong, Karem; Mcadams, Daniel A.; Norrell, Jeffery L.

1992-01-01

The National Aeronautics and Space Administration (NASA) in conjunction with Universities Space Research Association (USRA) has requested that the feasibility of a fleet of regolith tossing devices designed to cover a lunar habitat for radiation protection be demonstrated. The regolith, or lunar soil, protects the lunar habitat and its inhabitants from radiation. Ideally, the device will operate autonomously in the lunar environment. To prove the feasibility of throwing regolith on the Moon, throwing solutions were compared to traditional, Earth-based methods for moving soil. Various throwing configurations were investigated. A linear throwing motion combined with a spring and motor energizing system proved a superior solution. Three different overall configurations for the lunar device are presented. A single configuration is chosen and critical parameters such as operating procedure, system volume, mass, and power are developed. The report is divided into seven main sections. First, the Introduction section gives background information, defines the project requirements and the design criteria, and presents the methodology used for the completion of this design. Next, the Preliminary Analysis section presents background information on characteristics of lunar habitats and the lunar environment. Then, the Alternate Designs section presents alternate solutions to each of the critical functions of the device. Fourth, a detailed analysis of throwing the regolith is done to demonstrate its feasibility. Then, the three overall design configurations are presented. Next, a configuration is selected and the conceptual design is expanded to include system performance characteristics, size, and mass. Finally, the Conclusions and Recommendations for Future Work section evaluates the design, outlines the next step to be taken in the design process, and suggests possible goals for future design work.

Using Pathfinder networks to discover alignment between expert and consumer conceptual knowledge from online vaccine content.

PubMed

Amith, Muhammad; Cunningham, Rachel; Savas, Lara S; Boom, Julie; Schvaneveldt, Roger; Tao, Cui; Cohen, Trevor

2017-10-01

This study demonstrates the use of distributed vector representations and Pathfinder Network Scaling (PFNETS) to represent online vaccine content created by health experts and by laypeople. By analyzing a target audience's conceptualization of a topic, domain experts can develop targeted interventions to improve the basic health knowledge of consumers. The underlying assumption is that the content created by different groups reflects the mental organization of their knowledge. Applying automated text analysis to this content may elucidate differences between the knowledge structures of laypeople (heath consumers) and professionals (health experts). This paper utilizes vaccine information generated by laypeople and health experts to investigate the utility of this approach. We used an established technique from cognitive psychology, Pathfinder Network Scaling to infer the structure of the associational networks between concepts learned from online content using methods of distributional semantics. In doing so, we extend the original application of PFNETS to infer knowledge structures from individual participants, to infer the prevailing knowledge structures within communities of content authors. The resulting graphs reveal opportunities for public health and vaccination education experts to improve communication and intervention efforts directed towards health consumers. Our efforts demonstrate the feasibility of using an automated procedure to examine the manifestation of conceptual models within large bodies of free text, revealing evidence of conflicting understanding of vaccine concepts among health consumers as compared with health experts. Additionally, this study provides insight into the differences between consumer and expert abstraction of domain knowledge, revealing vaccine-related knowledge gaps that suggest opportunities to improve provider-patient communication. Copyright © 2017 Elsevier Inc. All rights reserved.

Conceptualizations of dignity at the end of life: exploring theoretical and cultural congruence with dignity therapy.

PubMed

Li, Hui-Ching; Richardson, Alison; Speck, Peter; Armes, Jo

2014-12-01

To explore the conceptualization of patients' dignity in the context of end-of-life care in Taiwan. Dignity therapy - a novel nurse-delivered psychotherapeutic intervention - has been demonstrated to have potential to alleviate terminal patients' psycho-existential distress in western countries. In Taiwan, over half of end-of-life patients experience psychological-spiritual suffering and dignity therapy might be helpful in improving this situation. Hence, a preliminary study to clarify Taiwanese conceptualizations of 'dignity' was conducted prior to planning a feasibility study to gauge the potential cultural fit of an intervention of this type. Qualitative exploration. Nine people with terminal cancer and ten health professionals were recruited from palliative care services in 2008. In-depth interviews were audiotaped and transcribed verbatim. A hermeneutic approach was employed to analyse and interpret data. Being a valuable person is the core meaning of patients' dignity and this comprised intrinsic characteristics and extrinsic factors. Intrinsic characteristics of dignity encompassed living a moral life, having peace of mind and a sense of existence involving the perception of resignation to God's will. Extrinsic factors that influenced patients' dignity included illness-related distress, care delivery and the perception of being loved. A dynamic relationship between these elements determined the state of patients' dignity. The concept of dignity is culturally bound and understood differently in the Chinese and Western context; such differences should be considered when planning and delivering care. Modifications should be made to dignity therapy to ensure it is culturally congruent with Taiwanese patients' beliefs. © 2014 John Wiley & Sons Ltd.

Dynamics and control of detumbling a disabled spacecraft during rescue operations

NASA Technical Reports Server (NTRS)

Kaplan, M. H.

1973-01-01

Results of a two-year research effort on dynamics and control of detumbling a disabled spacecraft during rescue operations are summarized. Answers to several basic questions about associated techniques and hardware requirements were obtained. Specifically, efforts have included development of operational procedures, conceptual design of remotely controlled modules, feasibility of internal moving mass for stabilization, and optimal techniques for minimum-time detumbling. Results have been documented in several reports and publications.

Feasibility of a special-purpose computer to solve the Navier-Stokes equations

NASA Technical Reports Server (NTRS)

Gritton, E. C.; King, W. S.; Sutherland, I.; Gaines, R. S.; Gazley, C., Jr.; Grosch, C.; Juncosa, M.; Petersen, H.

1978-01-01

Orders-of-magnitude improvements in computer performance can be realized with a parallel array of thousands of fast microprocessors. In this architecture, wiring congestion is minimized by limiting processor communication to nearest neighbors. When certain standard algorithms are applied to a viscous flow problem and existing LSI technology is used, performance estimates of this conceptual design show a dramatic decrease in computational time when compared to the CDC 7600.

A persuasive toothbrush to enhance oral hygiene adherence.

PubMed

Walji, Muhammad F; Coker, Ololade; Valenza, John A; Henson, Harold; Warren-Morris, Donna; Zhong, Lin

2008-11-06

In this research we propose that a real-time wireless monitoring and reminder system can assist patients in maintaining optimal oral health. We provide a conceptual framework that incorporates both the behavioral and technical aspects of the proposed system. Further we present preliminary results of a feasibility experiment of modifying an inexpensive electric toothbrush by attaching an accelerometer and determining the ability to track motion and time by wirelessly transmitting data via Bluetooth technology.

A conceptual model: Redesigning how we provide palliative care for patients with chronic obstructive pulmonary disease.

PubMed

Philip, Jennifer; Crawford, Gregory; Brand, Caroline; Gold, Michelle; Miller, Belinda; Hudson, Peter; Smallwood, Natasha; Lau, Rosalind; Sundararajan, Vijaya

2017-05-31

Despite significant needs, patients with chronic obstructive pulmonary disease (COPD) make limited use of palliative care, in part because the current models of palliative care do not address their key concerns. Our aim was to develop a tailored model of palliative care for patients with COPD and their family caregivers. Based on information gathered within a program of studies (qualitative research exploring experiences, a cohort study examining service use), an expert advisory committee evaluated and integrated data, developed responses, formulated principles to inform care, and made recommendations for practice. The informing studies were conducted in two Australian states: Victoria and South Australia. A series of principles underpinning the model were developed, including that it must be: (1) focused on patient and caregiver; (2) equitable, enabling access to components of palliative care for a group with significant needs; (3) accessible; and (4) less resource-intensive than expansion of usual palliative care service delivery. The recommended conceptual model was to have the following features: (a) entry to palliative care occurs routinely triggered by clinical transitions in care; (b) care is embedded in routine ambulatory respiratory care, ensuring that it is regarded as "usual" care by patients and clinicians alike; (c) the tasks include screening for physical and psychological symptoms, social and community support, provision of information, and discussions around goals and preferences for care; and (d) transition to usual palliative care services is facilitated as the patient nears death. Our proposed innovative and conceptual model for provision of palliative care requires future formal testing using rigorous mixed-methods approaches to determine if theoretical propositions translate into effectiveness, feasibility, and benefits (including economic benefits). There is reason to consider adaptation of the model for the palliative care of patients with other nonmalignant conditions.

Study of thermal energy storage using fluidized bed heat exchangers

NASA Technical Reports Server (NTRS)

Weast, T. E.; Shannon, L. J.; Ananth, K. P.

1980-01-01

The technical and economic feasibility of fluid bed heat exchangers (FBHX) for thermal energy storage (TES) in waste heat recovery applications is assessed by analysis of two selected conceptual systems, the rotary cement kiln and the electric arc furnace. It is shown that the inclusion of TES in the energy recovery system requires that the difference in off-peak and on-peak energy rates be large enough so that the value of the recovered energy exceeds the value of the stored energy by a wide enough margin to offset parasitic power and thermal losses. Escalation of on-peak energy rates due to fuel shortages could make the FBHX/TES applications economically attractive in the future.

Conceptual design of a lunar colony

NASA Technical Reports Server (NTRS)

Dalton, C. (Editor); Hohmann, E. (Editor)

1972-01-01

A systems engineering study is presented for a proposed lunar colony. The lunar colony was to grow from an existent, 12-man, earth-dependent lunar surface base and was to utilize lunar resources, becoming as earth-independent as possible. An in-depth treatment of some of the aspects of the lunar colony was given. We have found that the use of lunar resources is feasible for oxygen production (both for breathing and for space tug fuel), food production, and building materials. A program is outlined for recycling waste materials developed at the colony as well as a full program for growth and research activity of the colony to a level of 180 colonists. Recommendations for the lunar colony are given.

Coal gasifier cogeneration powerplant project

NASA Technical Reports Server (NTRS)

Shure, L. I.; Bloomfield, H. S.

1980-01-01

Industrial cogeneration and utility pr systems were analyzed and a conceptual design study was conducted to evaluate the economic feasibility of a coal gasifier power plant for NASA Lewis Research Center. Site location, plant size, and electric power demand were considered in criteria developed for screening and selecting candidates that could use a wide variety of coals, including that from Ohio. A fluidized bed gasifier concept was chosen as the baseline design and key components of the powerplant were technically assessed. No barriers to environmental acceptability are foreseen. If funded, the powerplant will not only meet the needs of the research center, but will reduce the commercial risk for utilities and industries by fully verifying and demonstrating the technology, thus accelerating commercialization.

From elementary flux modes to elementary flux vectors: Metabolic pathway analysis with arbitrary linear flux constraints.

PubMed

Klamt, Steffen; Regensburger, Georg; Gerstl, Matthias P; Jungreuthmayer, Christian; Schuster, Stefan; Mahadevan, Radhakrishnan; Zanghellini, Jürgen; Müller, Stefan

2017-04-01

Elementary flux modes (EFMs) emerged as a formal concept to describe metabolic pathways and have become an established tool for constraint-based modeling and metabolic network analysis. EFMs are characteristic (support-minimal) vectors of the flux cone that contains all feasible steady-state flux vectors of a given metabolic network. EFMs account for (homogeneous) linear constraints arising from reaction irreversibilities and the assumption of steady state; however, other (inhomogeneous) linear constraints, such as minimal and maximal reaction rates frequently used by other constraint-based techniques (such as flux balance analysis [FBA]), cannot be directly integrated. These additional constraints further restrict the space of feasible flux vectors and turn the flux cone into a general flux polyhedron in which the concept of EFMs is not directly applicable anymore. For this reason, there has been a conceptual gap between EFM-based (pathway) analysis methods and linear optimization (FBA) techniques, as they operate on different geometric objects. One approach to overcome these limitations was proposed ten years ago and is based on the concept of elementary flux vectors (EFVs). Only recently has the community started to recognize the potential of EFVs for metabolic network analysis. In fact, EFVs exactly represent the conceptual development required to generalize the idea of EFMs from flux cones to flux polyhedra. This work aims to present a concise theoretical and practical introduction to EFVs that is accessible to a broad audience. We highlight the close relationship between EFMs and EFVs and demonstrate that almost all applications of EFMs (in flux cones) are possible for EFVs (in flux polyhedra) as well. In fact, certain properties can only be studied with EFVs. Thus, we conclude that EFVs provide a powerful and unifying framework for constraint-based modeling of metabolic networks.

From elementary flux modes to elementary flux vectors: Metabolic pathway analysis with arbitrary linear flux constraints

PubMed Central

Klamt, Steffen; Gerstl, Matthias P.; Jungreuthmayer, Christian; Mahadevan, Radhakrishnan; Müller, Stefan

2017-01-01

Elementary flux modes (EFMs) emerged as a formal concept to describe metabolic pathways and have become an established tool for constraint-based modeling and metabolic network analysis. EFMs are characteristic (support-minimal) vectors of the flux cone that contains all feasible steady-state flux vectors of a given metabolic network. EFMs account for (homogeneous) linear constraints arising from reaction irreversibilities and the assumption of steady state; however, other (inhomogeneous) linear constraints, such as minimal and maximal reaction rates frequently used by other constraint-based techniques (such as flux balance analysis [FBA]), cannot be directly integrated. These additional constraints further restrict the space of feasible flux vectors and turn the flux cone into a general flux polyhedron in which the concept of EFMs is not directly applicable anymore. For this reason, there has been a conceptual gap between EFM-based (pathway) analysis methods and linear optimization (FBA) techniques, as they operate on different geometric objects. One approach to overcome these limitations was proposed ten years ago and is based on the concept of elementary flux vectors (EFVs). Only recently has the community started to recognize the potential of EFVs for metabolic network analysis. In fact, EFVs exactly represent the conceptual development required to generalize the idea of EFMs from flux cones to flux polyhedra. This work aims to present a concise theoretical and practical introduction to EFVs that is accessible to a broad audience. We highlight the close relationship between EFMs and EFVs and demonstrate that almost all applications of EFMs (in flux cones) are possible for EFVs (in flux polyhedra) as well. In fact, certain properties can only be studied with EFVs. Thus, we conclude that EFVs provide a powerful and unifying framework for constraint-based modeling of metabolic networks. PMID:28406903

Feasibility and acceptability of the DSM-5 Field Trial procedures in the Johns Hopkins Community Psychiatry Programs.

PubMed

Clarke, Diana E; Wilcox, Holly C; Miller, Leslie; Cullen, Bernadette; Gerring, Joan; Greiner, Lisa H; Newcomer, Alison; McKitty, Mellisha V; Regier, Darrel A; Narrow, William E

2014-06-01

The Diagnostic and Statistical Manual of Mental Disorders, Fifth Edition (DSM-5) contains criteria for psychiatric diagnoses that reflect advances in the science and conceptualization of mental disorders and address the needs of clinicians. DSM-5 also recommends research on dimensional measures of cross-cutting symptoms and diagnostic severity, which are expected to better capture patients' experiences with mental disorders. Prior to its May 2013 release, the American Psychiatric Association (APA) conducted field trials to examine the feasibility, clinical utility, reliability, and where possible, the validity of proposed DSM-5 diagnostic criteria and dimensional measures. The methods and measures proposed for the DSM-5 field trials were pilot tested in adult and child/adolescent clinical samples, with the goal to identify and correct design and procedural problems with the proposed methods before resources were expended for the larger DSM-5 Field Trials. Results allowed for the refinement of the protocols, procedures, and measures, which facilitated recruitment, implementation, and completion of the DSM-5 Field Trials. These results highlight the benefits of pilot studies in planning large multisite studies. Copyright © 2013, American Psychiatric Association. All rights reserved.

Space station integrated wall damage and penetration damage control. Task 5: Space debris measurement, mapping and characterization system

NASA Technical Reports Server (NTRS)

Lempriere, B. M.

1987-01-01

The procedures and results of a study of a conceptual system for measuring the debris environment on the space station is discussed. The study was conducted in two phases: the first consisted of experiments aimed at evaluating location of impact through panel response data collected from acoustic emission sensors; the second analyzed the available statistical description of the environment to determine the probability of the measurement system producing useful data, and analyzed the results of the previous tests to evaluate the accuracy of location and the feasibility of extracting impactor characteristics from the panel response. The conclusions were that for one panel the system would not be exposed to any event, but that the entire Logistics Module would provide a modest amount of data. The use of sensors with higher sensitivity than those used in the tests could be advantageous. The impact location could be found with sufficient accuracy from panel response data. The waveforms of the response were shown to contain information on the impact characteristics, but the data set did not span a sufficient range of the variables necessary to evaluate the feasibility of extracting the information.

Design of internal support structures for an inflatable lunar habitat

NASA Technical Reports Server (NTRS)

Cameron, Elizabeth A.; Duston, John A.; Lee, David D.

1990-01-01

NASA has a long range goal of constructing a fully equipped, manned lunar outpost on the near side of the moon by the year 2015. The proposed outpost includes an inflatable lunar habitat to support crews during missions longer that 12 months. A design for the internal support structures of the inflatable habitat is presented. The design solution includes material selection, substructure design, assembly plan development, and concept scale model construction. Alternate designs and design solutions for each component of the design are discussed. Alternate materials include aluminum, titanium, and reinforced polymers. Vertical support alternates include column systems, truss systems, suspension systems, and lunar lander supports. Horizontal alternates include beams, trusses, floor/truss systems, and expandable trusses. Feasibility studies on each alternate showed that truss systems and expandable trusses were the most feasible candidates for conceptual design. The team based the designs on the properties of 7075 T73 aluminum. The substructure assembly plan, minimizes assembly time and allows crews to construct the habitat without the use of EVA suits. In addition to the design solutions, the report gives conclusions and recommendations for further study of the inflatable habitat design.

Space Station Furnace Facility. Volume 1: Requirements definition and conceptual design study, executive summary

NASA Technical Reports Server (NTRS)

1992-01-01

The Space Station Freedom Furnace (SSFF) Study was awarded on June 2, 1989, to Teledyne Brown Engineering (TBE) to define an advanced facility for materials research in the microgravity environment of Space Station Freedom (SSF). The SSFF will be designed for research in the solidification of metals and alloys, the crystal growth of electronic and electro-optical materials, and research in glasses and ceramics. The SSFF is one of the first 'facility' class payloads planned by the Microgravity Science and Applications Division (MSAD) of the Office of Space Science and Applications of NASA Headquarters. This facility is planned for early deployment during man-tended operations of the SSF with continuing operations through the Permanently Manned Configuration (PMC). The SSFF will be built around a general 'Core' facility which provides common support functions not provided by SSF, common subsystems which are best centralized, and common subsystems which are best distributed with each experiment module. The intent of the facility approach is to reduce the overall cost associated with implementing and operating a variety of experiments. This is achieved by reducing the launch mass and simplifying the hardware development and qualification processes associated with each experiment. The Core will remain on orbit and will require only periodic maintenance and upgrading while new Furnace Modules, samples, and consumables are developed, qualified, and transported to the SSF. The SSFF Study was divided into two phases: phase 1, a definition study phase, and phase 2, a design and development phase. The definition phase 1 is addressed. Phase 1 was divided into two parts. In the first part, the basic part of the effort, covered the preliminary definition and assessment of requirements; conceptual design of the SSFF; fabrication of mockups; and the preparation for and support of the Conceptual Design Review (CoDR). The second part, the option part, covered requirements update and documentation; refinement of the selected conceptual design through additional trades and analyses; design, fabrication, and test of the Development Model; and design, fabrication, and test of the Interrack Demonstration Unit; and support of the requirements definition review (RDR). The purpose of part 2 was to prove concept feasibility.

Expendable solid rocket motor upper stages for the Space Shuttle

NASA Technical Reports Server (NTRS)

Davis, H. P.; Jones, C. M.

1974-01-01

A family of expendable solid rocket motor upper stages has been conceptually defined to provide the payloads for the Space Shuttle with performance capability beyond the low earth operational range of the Shuttle Orbiter. In this concept-feasibility assessment, three new solid rocket motors of fixed impulse are defined for use with payloads requiring levels of higher energy. The conceptual design of these motors is constrained to limit thrusting loads into the payloads and to conserve payload bay length. These motors are combined in various vehicle configurations with stage components derived from other programs for the performance of a broad range of upper-stage missions from spin-stabilized, single-stage transfers to three-axis stabilized, multistage insertions. Estimated payload delivery performance and combined payload mission loading configurations are provided for the upper-stage configurations.

Preliminary economic analysis of aquifer winter-chill storage at the John F. Kennedy airport

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fox, E.C.; Thomas, J.F.

A conceptual design was formulated in conjuction with a cost analysis to determine the feasibility of retrofitting the present John F. Kennedy (JFK) airport air-conditioning system with an aquifer cold water storage system. It appears technically feasible to chill and store aquifer water at the airport site during the winter months for later air-conditioning use. However, the economic analysis shows that although a significant energy savings is realized, the money saved from reduced energy costs would not be enough to recover the necessary capital investment over a 20-year period. JFK airport may be a poor economic choice for an aquifermore » cold water storage demonstration site due to site specific problems, and other sites may provide economic incentive.« less

Research on advanced transportation systems

NASA Astrophysics Data System (ADS)

Nagai, Hirokazu; Hashimoto, Ryouhei; Nosaka, Masataka; Koyari, Yukio; Yamada, Yoshio; Noda, Keiichirou; Shinohara, Suetsugu; Itou, Tetsuichi; Etou, Takao; Kaneko, Yutaka

1992-08-01

An overview of the researches on advanced space transportation systems is presented. Conceptual study is conducted on fly back boosters with expendable upper stage rocket systems assuming a launch capacity of 30 tons and returning to the launch site by the boosters, and prospect of their feasibility is obtained. Reviews are conducted on subjects as follows: (1) trial production of 10 tons sub scale engines for the purpose of acquiring hardware data and picking up technical problems for full scale 100 tons thrust engines using hydrocarbon fuels; (2) development techniques for advanced liquid propulsion systems from the aspects of development schedule, cost; (3) review of conventional technologies, and common use of component; (4) oxidant switching propulsion systems focusing on feasibility of Liquefied Air Cycle Engine (LACE) and Compressed Air Cycle Engine (CACE); (5) present status of slosh hydrogen manufacturing, storage, and handling; (6) construction of small high speed dynamometer for promoting research on mini pump development; (7) hybrid solid boosters under research all over the world as low-cost and clean propulsion systems; and (8) high performance solid propellant for upper stage and lower stage propulsion systems.

Research on air sprays and unique foam application methods. Phase II report. Laboratory investigation of foam systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1982-06-01

The objective of this study is to assess the effectiveness of air sprays and foam systems for dust control on longwall double-drum shearer faces. Laboratory testing has been conducted using foam systems and promising results have been obtained. Upon Bureau approval, underground testing will be scheduled to assess the effectiveness of foam systems under actual operating conditions. Laboratory testing of air sprays is being conducted at present. This report presents the results of the laboratory testing of foam systems. Specifically, the results obtained on the evaluation of selected foaming agents are presented, the feasibility investigation of flushing foam through themore » shearer-drum are demonstrated, and conceptual layout of the foam system on the shearer is discussed. The laboratory investigation of the selected foaming agents reveal that the Onyx Microfoam, Onyx Maprosyl and DeTer Microfoam foaming agents have higher expansion ratios compared to the others tested. Flushing foam through the shearer drum is entirely feasible and could be a viable technique for dust suppression on longwall faces.« less

Space station Simulation Computer System (SCS) study for NASA/MSFC. Volume 4: Conceptual design report

NASA Technical Reports Server (NTRS)

1989-01-01

The Simulation Computer System (SCS) is the computer hardware, software, and workstations that will support the Payload Training Complex (PTC) at Marshall Space Flight Center (MSFC). The PTC will train the space station payload scientists, station scientists, and ground controllers to operate the wide variety of experiments that will be onboard the Space Station Freedom. In the first step of this task, a methodology was developed to ensure that all relevant design dimensions were addressed, and that all feasible designs could be considered. The development effort yielded the following method for generating and comparing designs in task 4: (1) Extract SCS system requirements (functions) from the system specification; (2) Develop design evaluation criteria; (3) Identify system architectural dimensions relevant to SCS system designs; (4) Develop conceptual designs based on the system requirements and architectural dimensions identified in step 1 and step 3 above; (5) Evaluate the designs with respect to the design evaluation criteria developed in step 2 above. The results of the method detailed in the above 5 steps are discussed. The results of the task 4 work provide the set of designs which two or three candidate designs are to be selected by MSFC as input to task 5-refine SCS conceptual designs. The designs selected for refinement will be developed to a lower level of detail, and further analyses will be done to begin to determine the size and speed of the components required to implement these designs.

Updated Conceptual Model for the 300 Area Uranium Groundwater Plume

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zachara, John M.; Freshley, Mark D.; Last, George V.

2012-11-01

The 300 Area uranium groundwater plume in the 300-FF-5 Operable Unit is residual from past discharge of nuclear fuel fabrication wastes to a number of liquid (and solid) disposal sites. The source zones in the disposal sites were remediated by excavation and backfilled to grade, but sorbed uranium remains in deeper, unexcavated vadose zone sediments. In spite of source term removal, the groundwater plume has shown remarkable persistence, with concentrations exceeding the drinking water standard over an area of approximately 1 km2. The plume resides within a coupled vadose zone, groundwater, river zone system of immense complexity and scale. Interactionsmore » between geologic structure, the hydrologic system driven by the Columbia River, groundwater-river exchange points, and the geochemistry of uranium contribute to persistence of the plume. The U.S. Department of Energy (DOE) recently completed a Remedial Investigation/Feasibility Study (RI/FS) to document characterization of the 300 Area uranium plume and plan for beginning to implement proposed remedial actions. As part of the RI/FS document, a conceptual model was developed that integrates knowledge of the hydrogeologic and geochemical properties of the 300 Area and controlling processes to yield an understanding of how the system behaves and the variables that control it. Recent results from the Hanford Integrated Field Research Challenge site and the Subsurface Biogeochemistry Scientific Focus Area Project funded by the DOE Office of Science were used to update the conceptual model and provide an assessment of key factors controlling plume persistence.« less

Gas-Grain Simulation Facility (GGSF). Volume 1: Stage 1 facility definition studies

NASA Technical Reports Server (NTRS)

Gat, Nahum

1993-01-01

The Gas-Grain Simulation Facility (GGSF) is a facility-type payload to be included in the Space Station Freedom (SSF). The GGSF is a multidisciplinary facility that will accommodate several classes of experiments, including exobiology, planetary science, atmospheric science, and astrophysics. The physical mechanisms envisioned to be investigated include crystal growth, aggregation, nucleation, coagulation, condensation, collisions, fractal growth, cycles of freezing and evaporation, scavenging, longevity of bacteria, and more. TRW performed a Phase A study that included analyses of the science and technical (S&T) requirements, the development of facility functional requirements, and a conceptual design of the facility. The work that was performed under Stage 1 of the Phase A study and the results to date are summarized. In this stage, facility definition studies were conducted in sufficient detail to establish the technical feasibility of the candidate strawman experiments. The studies identified technical difficulties, identified required facility subsystems, surveyed existing technology studies and established preliminary facility weight, volume, power consumption, data systems, interface definition, and crew time requirements. The results of this study served as the basis for Stage 2 of the Phase A study in which a conceptual design and a reference design were performed. The results also served as a basis for a related study for a Gas-Grain Simulation Experiment Module (GGSEM), which is an apparatus intended to perform a subset of the GGSF experiments on board a low-Earth-orbiting platform.

Study of aerodynamic technology for VSTOL fighter/attack aircraft: Vertical attitude concept

NASA Technical Reports Server (NTRS)

Gerhardt, H. A.; Chen, W. S.

1978-01-01

The aerodynamic technology for a vertical attitude VSTOL (VATOL) supersonic fighter/attack aircraft was studied. The selected configuration features a tailless clipped delta wing with leading-edge extension (LEX), maneuvering flaps, top-side inlet, twin dry engines and vectoring nozzles. A relaxed static stability is employed in conjunction with the maneuvering flaps to optimize transonic performance and minimize supersonic trim drag. Control for subaerodynamic flight is obtained by gimballing the nozzles in combination with wing tip jets. Emphasis is placed on the development of aerodynamic characteristics and the identification of aerodynamic uncertainties. A wind tunnel test program is proposed to resolve these uncertainties and ascertain the feasibility of the conceptual design. Ship interface, flight control integration, crew station concepts, advanced weapons, avionics, and materials are discussed.

Terahertz-Regime, Micro-VEDs: Evaluation of Micromachined TWT Conceptual Designs

NASA Technical Reports Server (NTRS)

Booske, John H.; Kory, Carol L.; Gallagher, D.; van der Weide, Daniel W.; Limbach, S; Gustafson, P; Lee, W.-J.; Gallagher, S.; Jain, K.

2001-01-01

Summary form only given. The Terahertz (THz) region of the electromagnetic spectrum (approx.300-3000 GHz) has enormous potential for high-data-rate communications, spectroscopy, astronomy, space research, medicine, biology, surveillance, remote sensing, industrial process control, etc. The most critical roadblock to full exploitation of the THz band is lack of coherent radiation sources that are powerful (0.01-10.0 W continuous wave), efficient (>1 %), frequency agile (instantaneously tunable over 1% bandwidths or more), reliable, and relatively inexpensive. Micro-machined Vacuum Electron Devices (micro-VEDs) represent a promising solution. We describe prospects for miniature, THz-regime TWTs fabricated using micromachining techniques. Several approx.600 GHz conceptual designs are compared. Their expected performance has been analyzed using SD, 2.51), and 3D TWT codes. A folded waveguide (FWG) TWT forward-wave amplifier design is presented based on a Northrop Grumman (NGC) optimized design procedure. This conceptual device is compared to the simulated performance of a novel, micro-VED helix TWT. Conceptual FWG TWT backward-wave amplifiers and oscillators are also discussed. A scaled (100 GHz) FWG TWT operating at a relatively low voltage (-12 kV) is under development at NGC. Also, actual-size micromachining experiments are planned to evaluate the feasibility of arrays of micro-VED TWTs. Progress and results of these efforts are described. This work was supported, in part by AFOSR, ONR, and NSF.

The SWATH Concept: Designing Superior Operability into a Surface Displacement Ship

DTIC Science & Technology

1975-12-01

ACKNOWLEDGMENTS 140 REFERENCES 141 —^f* • ■ " mil,. .„.. • LIST OF FIGURES Page 1 — Artist’s Concept of a 4000-Ton ", WATH Combatant 4 2 ~ The...the design process for SWATH combatants is iterative. At either the feasibility or conceptual stage, the designer starts with a "reasonable" hull...parameters, the multitude of design factors and innumerable combinations thereof constitute a difficult synthesis problem. Because they are

The Amagugu Intervention: A Conceptual Framework for Increasing HIV Disclosure and Parent-Led Communication about Health among HIV-Infected Parents with HIV-Uninfected Primary School-Aged Children

PubMed Central

Rochat, Tamsen J.; Mitchell, Joanie; Stein, Alan; Mkwanazi, Ntombizodumo Brilliant; Bland, Ruth M.

2016-01-01

Advances in access to HIV prevention and treatment have reduced vertical transmission of HIV, with most children born to HIV-infected parents being HIV-uninfected themselves. A major challenge that HIV-infected parents face is disclosure of their HIV status to their predominantly HIV-uninfected children. Their children enter middle childhood and early adolescence facing many challenges associated with parental illness and hospitalization, often exacerbated by stigma and a lack of access to health education and support. Increasingly, evidence suggests that primary school-aged children have the developmental capacity to grasp concepts of health and illness, including HIV, and that in the absence of parent-led communication and education about these issues, HIV-exposed children may be at increased risk of psychological and social problems. The Amagugu intervention is a six-session home-based intervention, delivered by lay counselors, which aims to increase parenting capacity to disclose their HIV status and offer health education to their primary school-aged children. The intervention includes information and activities on disclosure, health care engagement, and custody planning. An uncontrolled pre–post-evaluation study with 281 families showed that the intervention was feasible, acceptable, and effective in increasing maternal disclosure. The aim of this paper is to describe the conceptual model of the Amagugu intervention, as developed post-evaluation, showing the proposed pathways of risk that Amagugu aims to disrupt through its intervention targets, mechanisms, and activities; and to present a summary of results from the large-scale evaluation study of Amagugu to demonstrate the acceptability and feasibility of the intervention model. This relatively low-intensity home-based intervention led to: increased HIV disclosure to children, improvements in mental health for mother and child, and improved health care engagement and custody planning for the child. The intervention model demonstrates the potential for disclosure interventions to include pre-adolescent HIV education and prevention for primary school-aged children. PMID:27630981

Providing a conceptual framework for HIV prevention cascades and assessing feasibility of empirical measurement with data from east Zimbabwe: a case study.

PubMed

Garnett, Geoffrey P; Hallett, Timothy B; Takaruza, Albert; Hargreaves, James; Rhead, Rebecca; Warren, Mitchel; Nyamukapa, Constance; Gregson, Simon

2016-07-01

The HIV treatment cascade illustrates the steps required for successful treatment and is a powerful advocacy and monitoring tool. Similar cascades for people susceptible to infection could improve HIV prevention programming. We aim to show the feasibility of using cascade models to monitor prevention programmes. Conceptual prevention cascades are described taking intervention-centric and client-centric perspectives to look at supply, demand, and efficacy of interventions. Data from two rounds of a population-based study in east Zimbabwe are used to derive the values of steps for cascades for voluntary medical male circumcision (VMMC) and for partner reduction or condom use driven by HIV testing and counselling (HTC). In 2009 to 2011 the availability of circumcision services was negligible, but by 2012 to 2013 about a third of the population had access. However, where it was available only 12% of eligible men sought to be circumcised leading to an increase in circumcision prevalence from 3·1% to 6·9%. Of uninfected men, 85·3% did not perceive themselves to be at risk of acquiring HIV. The proportions of men and women tested for HIV increased from 27·5% to 56·6% and from 61·1% to 79·6%, respectively, with 30·4% of men tested self-reporting reduced sexual partner numbers and 12·8% reporting increased condom use. Prevention cascades can be populated to inform HIV prevention programmes. In eastern Zimbabwe programmes need to provide greater access to circumcision services and the design and implementation of associated demand creation activities. Whereas, HTC services need to consider how to increase reductions in partner numbers or increased condom use or should not be considered as contributing to prevention services for the HIV-negative adults. Wellcome Trust and Bill & Melinda Gates Foundation. Copyright © 2016 Garnett et al. Open Access article distributed under the terms of CC BY. Published by Elsevier Ltd.. All rights reserved.

Microbial Metagenomics: Beyond the Genome

NASA Astrophysics Data System (ADS)

Gilbert, Jack A.; Dupont, Christopher L.

2011-01-01

Metagenomics literally means “beyond the genome.” Marine microbial metagenomic databases presently comprise ˜400 billion base pairs of DNA, only ˜3% of that found in 1 ml of seawater. Very soon a trillion-base-pair sequence run will be feasible, so it is time to reflect on what we have learned from metagenomics. We review the impact of metagenomics on our understanding of marine microbial communities. We consider the studies facilitated by data generated through the Global Ocean Sampling expedition, as well as the revolution wrought at the individual laboratory level through next generation sequencing technologies. We review recent studies and discoveries since 2008, provide a discussion of bioinformatic analyses, including conceptual pipelines and sequence annotation and predict the future of metagenomics, with suggestions of collaborative community studies tailored toward answering some of the fundamental questions in marine microbial ecology.

Agri-Environmental Policy Measures in Israel: The Potential of Using Market-Oriented Instruments

NASA Astrophysics Data System (ADS)

Amdur, Liron; Bertke, Elke; Freese, Jan; Marggraf, Rainer

2011-05-01

This paper examines the possibilities of developing agri-environmental policy measures in Israel, focusing on market-oriented instruments. A conceptual framework for developing agri-environmental policy measures is presented, first in very broad lines (mandatory regulations, economic instruments and advisory measures) and subsequently focusing on economic instruments, and specifically, on market-oriented ones. Two criteria of choice between the measures are suggested: their contribution to improving the effectiveness of the policy; and the feasibility of their implementation. This is the framework used for analyzing agri-environmental measures in Israel. Israel currently implements a mix of mandatory regulations, economic instruments and advisory measures to promote the agri-environment. The use of additional economic instruments may improve the effectiveness of the policy. When comparing the effectiveness of various economic measures, we found that the feasibility of implementation of market-oriented instruments is greater, due to the Israeli public's preference for strengthening market orientation in the agricultural sector. Four market-oriented instruments were practiced in a pilot project conducted in an Israeli rural area. We found that in this case study, the institutional feasibility and acceptance by stakeholders were the major parameters influencing the implementation of the market-oriented instruments, whereas the instruments' contribution to enhancing the ecological or economic effectiveness were hardly considered by the stakeholders as arguments in favor of their use.

Agri-environmental policy measures in Israel: the potential of using market-oriented instruments.

PubMed

Amdur, Liron; Bertke, Elke; Freese, Jan; Marggraf, Rainer

2011-05-01

This paper examines the possibilities of developing agri-environmental policy measures in Israel, focusing on market-oriented instruments. A conceptual framework for developing agri-environmental policy measures is presented, first in very broad lines (mandatory regulations, economic instruments and advisory measures) and subsequently focusing on economic instruments, and specifically, on market-oriented ones. Two criteria of choice between the measures are suggested: their contribution to improving the effectiveness of the policy; and the feasibility of their implementation. This is the framework used for analyzing agri-environmental measures in Israel. Israel currently implements a mix of mandatory regulations, economic instruments and advisory measures to promote the agri-environment. The use of additional economic instruments may improve the effectiveness of the policy. When comparing the effectiveness of various economic measures, we found that the feasibility of implementation of market-oriented instruments is greater, due to the Israeli public's preference for strengthening market orientation in the agricultural sector. Four market-oriented instruments were practiced in a pilot project conducted in an Israeli rural area. We found that in this case study, the institutional feasibility and acceptance by stakeholders were the major parameters influencing the implementation of the market-oriented instruments, whereas the instruments' contribution to enhancing the ecological or economic effectiveness were hardly considered by the stakeholders as arguments in favor of their use.

Data management in an object-oriented distributed aircraft conceptual design environment

NASA Astrophysics Data System (ADS)

Lu, Zhijie

In the competitive global market place, aerospace companies are forced to deliver the right products to the right market, with the right cost, and at the right time. However, the rapid development of technologies and new business opportunities, such as mergers, acquisitions, supply chain management, etc., have dramatically increased the complexity of designing an aircraft. Therefore, the pressure to reduce design cycle time and cost is enormous. One way to solve such a dilemma is to develop and apply advanced engineering environments (AEEs), which are distributed collaborative virtual design environments linking researchers, technologists, designers, etc., together by incorporating application tools and advanced computational, communications, and networking facilities. Aircraft conceptual design, as the first design stage, provides major opportunity to compress design cycle time and is the cheapest place for making design changes. However, traditional aircraft conceptual design programs, which are monolithic programs, cannot provide satisfactory functionality to meet new design requirements due to the lack of domain flexibility and analysis scalability. Therefore, we are in need of the next generation aircraft conceptual design environment (NextADE). To build the NextADE, the framework and the data management problem are two major problems that need to be addressed at the forefront. Solving these two problems, particularly the data management problem, is the focus of this research. In this dissertation, in light of AEEs, a distributed object-oriented framework is firstly formulated and tested for the NextADE. In order to improve interoperability and simplify the integration of heterogeneous application tools, data management is one of the major problems that need to be tackled. To solve this problem, taking into account the characteristics of aircraft conceptual design data, a robust, extensible object-oriented data model is then proposed according to the distributed object-oriented framework. By overcoming the shortcomings of the traditional approach of modeling aircraft conceptual design data, this data model makes it possible to capture specific detailed information of aircraft conceptual design without sacrificing generality, which is one of the most desired features of a data model for aircraft conceptual design. Based upon this data model, a prototype of the data management system, which is one of the fundamental building blocks of the NextADE, is implemented utilizing the state of the art information technologies. Using a general-purpose integration software package to demonstrate the efficacy of the proposed framework and the data management system, the NextADE is initially implemented by integrating the prototype of the data management system with other building blocks of the design environment, such as disciplinary analyses programs and mission analyses programs. As experiments, two case studies are conducted in the integrated design environments. One is based upon a simplified conceptual design of a notional conventional aircraft; the other is a simplified conceptual design of an unconventional aircraft. As a result of the experiments, the proposed framework and the data management approach are shown to be feasible solutions to the research problems.

Advanced hybrid vehicle propulsion system study

NASA Technical Reports Server (NTRS)

Schwarz, R.

1982-01-01

Results are presented of a study of an advanced heat engine/electric automotive hybrid propulsion system. The system uses a rotary stratified charge engine and ac motor/controller in a parallel hybrid configuration. The three tasks of the study were (1) parametric studies involving five different vehicle types, (2) design trade-off studies to determine the influence of various vehicle and propulsion system paramaters on system performance fuel economy and cost, and (3) a conceptual design establishing feasibility at the selected approach. Energy consumption for the selected system was .034 1/km (61.3 mpg) for the heat engine and .221 kWh/km (.356 kWh/mi) for the electric power system over a modified J227 a schedule D driving cycle. Life cycle costs were 7.13 cents/km (11.5 cents/mi) at $2/gal gasoline and 7 cents/kWh electricity for 160,000 km (100,000 mi) life.

A method for scenario-based risk assessment for robust aerospace systems

NASA Astrophysics Data System (ADS)

Thomas, Victoria Katherine

In years past, aircraft conceptual design centered around creating a feasible aircraft that could be built and could fly the required missions. More recently, aircraft viability entered into conceptual design, allowing that the product's potential to be profitable should also be examined early in the design process. While examining an aerospace system's feasibility and viability early in the design process is extremely important, it is also important to examine system risk. In traditional aerospace systems risk analysis, risk is examined from the perspective of performance, schedule, and cost. Recently, safety and reliability analysis have been brought forward in the design process to also be examined during late conceptual and early preliminary design. While these analyses work as designed, existing risk analysis methods and techniques are not designed to examine an aerospace system's external operating environment and the risks present there. A new method has been developed here to examine, during the early part of concept design, the risk associated with not meeting assumptions about the system's external operating environment. The risks are examined in five categories: employment, culture, government and politics, economics, and technology. The risks are examined over a long time-period, up to the system's entire life cycle. The method consists of eight steps over three focus areas. The first focus area is Problem Setup. During problem setup, the problem is defined and understood to the best of the decision maker's ability. There are four steps in this area, in the following order: Establish the Need, Scenario Development, Identify Solution Alternatives, and Uncertainty and Risk Identification. There is significant iteration between steps two through four. Focus area two is Modeling and Simulation. In this area the solution alternatives and risks are modeled, and a numerical value for risk is calculated. A risk mitigation model is also created. The four steps involved in completing the modeling and simulation are: Alternative Solution Modeling, Uncertainty Quantification, Risk Assessment, and Risk Mitigation. Focus area three consists of Decision Support. In this area a decision support interface is created that allows for game playing between solution alternatives and risk mitigation. A multi-attribute decision making process is also implemented to aid in decision making. A demonstration problem inspired by Airbus' mid 1980s decision to break into the widebody long-range market was developed to illustrate the use of this method. The results showed that the method is able to capture additional types of risk than previous analysis methods, particularly at the early stages of aircraft design. It was also shown that the method can be used to help create a system that is robust to external environmental factors. The addition of an external environment risk analysis in the early stages of conceptual design can add another dimension to the analysis of feasibility and viability. The ability to take risk into account during the early stages of the design process can allow for the elimination of potentially feasible and viable but too-risky alternatives. The addition of a scenario-based analysis instead of a traditional probabilistic analysis enabled uncertainty to be effectively bound and examined over a variety of potential futures instead of only a single future. There is also potential for a product to be groomed for a specific future that one believes is likely to happen, or for a product to be steered during design as the future unfolds.

On the feasibility of concurrent human TMS-EEG-fMRI measurements

PubMed Central

Reithler, Joel; Schuhmann, Teresa; de Graaf, Tom; Uludağ, Kâmil; Goebel, Rainer; Sack, Alexander T.

2013-01-01

Simultaneously combining the complementary assets of EEG, functional MRI (fMRI), and transcranial magnetic stimulation (TMS) within one experimental session provides synergetic results, offering insights into brain function that go beyond the scope of each method when used in isolation. The steady increase of concurrent EEG-fMRI, TMS-EEG, and TMS-fMRI studies further underlines the added value of such multimodal imaging approaches. Whereas concurrent EEG-fMRI enables monitoring of brain-wide network dynamics with high temporal and spatial resolution, the combination with TMS provides insights in causal interactions within these networks. Thus the simultaneous use of all three methods would allow studying fast, spatially accurate, and distributed causal interactions in the perturbed system and its functional relevance for intact behavior. Concurrent EEG-fMRI, TMS-EEG, and TMS-fMRI experiments are already technically challenging, and the three-way combination of TMS-EEG-fMRI might yield additional difficulties in terms of hardware strain or signal quality. The present study explored the feasibility of concurrent TMS-EEG-fMRI studies by performing safety and quality assurance tests based on phantom and human data combining existing commercially available hardware. Results revealed that combined TMS-EEG-fMRI measurements were technically feasible, safe in terms of induced temperature changes, allowed functional MRI acquisition with comparable image quality as during concurrent EEG-fMRI or TMS-fMRI, and provided artifact-free EEG before and from 300 ms after TMS pulse application. Based on these empirical findings, we discuss the conceptual benefits of this novel complementary approach to investigate the working human brain and list a number of precautions and caveats to be heeded when setting up such multimodal imaging facilities with current hardware. PMID:23221407

Conceptual Design of a Nano-Networking Device

PubMed Central

Canovas-Carrasco, Sebastian; Garcia-Sanchez, Antonio-Javier; Garcia-Sanchez, Felipe; Garcia-Haro, Joan

2016-01-01

Nanotechnology is an emerging scientific area whose advances, among many others, have a positive direct impact on the miniaturization of electronics. This unique technology enables the possibility to design and build electronic components as well as complete devices (called nanomachines or nanodevices) at the nano scale. A nanodevice is expected to be an essential element able to operate in a nanonetwork, where a huge number of them would coordinate to acquire data, process the information gathered, and wirelessly transmit those data to end-points providing innovative services in many key scenarios, such as the human body or the environment. This paper is aimed at studying the feasibility of this type of device by carefully examining their main component parts, namely the nanoprocessor, nanomemory, nanoantenna, and nanogenerator. To this end, a thorough state-of-the-art review is conveyed to discuss, substantiate, and select the most suitable current technology (commercial or pre-commercial) for each component. Then, we further contribute by developing a complete conceptual nanodevice layout taking into consideration its ultra-small size (similar to a blood cell) and its very restricted capabilities (e.g., processing, memory storage, telecommunication, and energy management). The required resources as well as the power consumption are realistically estimated. PMID:27973430

Performance Assessment Uncertainty Analysis for Japan's HLW Program Feasibility Study (H12)

DOE Office of Scientific and Technical Information (OSTI.GOV)

BABA,T.; ISHIGURO,K.; ISHIHARA,Y.

1999-08-30

Most HLW programs in the world recognize that any estimate of long-term radiological performance must be couched in terms of the uncertainties derived from natural variation, changes through time and lack of knowledge about the essential processes. The Japan Nuclear Cycle Development Institute followed a relatively standard procedure to address two major categories of uncertainty. First, a FEatures, Events and Processes (FEPs) listing, screening and grouping activity was pursued in order to define the range of uncertainty in system processes as well as possible variations in engineering design. A reference and many alternative cases representing various groups of FEPs weremore » defined and individual numerical simulations performed for each to quantify the range of conceptual uncertainty. Second, parameter distributions were developed for the reference case to represent the uncertainty in the strength of these processes, the sequencing of activities and geometric variations. Both point estimates using high and low values for individual parameters as well as a probabilistic analysis were performed to estimate parameter uncertainty. A brief description of the conceptual model uncertainty analysis is presented. This paper focuses on presenting the details of the probabilistic parameter uncertainty assessment.« less

Conceptual Design of a Nano-Networking Device.

PubMed

Canovas-Carrasco, Sebastian; Garcia-Sanchez, Antonio-Javier; Garcia-Sanchez, Felipe; Garcia-Haro, Joan

2016-12-11

Nanotechnology is an emerging scientific area whose advances, among many others, have a positive direct impact on the miniaturization of electronics. This unique technology enables the possibility to design and build electronic components as well as complete devices (called nanomachines or nanodevices) at the nano scale. A nanodevice is expected to be an essential element able to operate in a nanonetwork, where a huge number of them would coordinate to acquire data, process the information gathered, and wirelessly transmit those data to end-points providing innovative services in many key scenarios, such as the human body or the environment. This paper is aimed at studying the feasibility of this type of device by carefully examining their main component parts, namely the nanoprocessor, nanomemory, nanoantenna, and nanogenerator. To this end, a thorough state-of-the-art review is conveyed to discuss, substantiate, and select the most suitable current technology (commercial or pre-commercial) for each component. Then, we further contribute by developing a complete conceptual nanodevice layout taking into consideration its ultra-small size (similar to a blood cell) and its very restricted capabilities (e.g., processing, memory storage, telecommunication, and energy management). The required resources as well as the power consumption are realistically estimated.

Rock Melt Borehole Sealing System, Final Technical Report for SBIR Phase I Grant No. DE-SC0011888

DOE Office of Scientific and Technical Information (OSTI.GOV)

Osnes, John D.; Vining, Cody A.; Nopola, Jay R.

Purpose of Research Deep borehole disposal is one option that has received attention in recent years as a possible strategy for long-term disposal of the tens of thousands of tons of spent nuclear fuel. The feasibility of the deep borehole option relies upon designing and constructing an effective seal within the borehole to ensure that the waste package does not communicate with the shallow subsurface biosphere through the borehole itself. Some of the uncertainty associated with the long-term suitability of the deep borehole option is related to (1) the degradation of traditional sealing materials over time and (2) the inabilitymore » of traditional sealing methods to adequately seal a Disturbed Rock Zone surrounding the borehole. One possible system to address these concerns consists of encapsulating the waste in a melt generated from either the waste itself or a plug above the waste. This current project expanded on previous work to further advance the deep borehole disposal concept. Research Objectives & Findings The overarching objective of the study was to evaluate the feasibility of constructing a downhole heater that is capable of meeting the technical and logistical requirements to melt rock. This ultimate objective was accomplished by two primary approaches. The first approach was to define the heater requirements and conceptually design a system that is capable of melting rock. The second approach was to determine the feasibility of conducting an in situ, field-scale melting experiment to validate the suitability of the rock melt seal concept. The evaluation and conceptual design of the heater system resulted in the following primary findings: • Borehole wall temperatures capable of producing a partial melt are achievable under most expected thermal conductivities with a 12-kilowatt heater. • Commercially available components have been identified that meet the requirements of the heater system, including resistive elements that are capable of providing the required heat generation, container materials that can withstand the anticipated temperatures, and a system capable of providing power to the heater. Evaluating the feasibility of performing field-scale experiments resulted in the following major findings: • The Sanford Underground Research Facility (SURF) has been identified as a host site for field testing of prototype heaters. The technical and logistical requirements for performing the rock melt tests can be met by using or expanding the existing infrastructure at SURF with on-site personnel and contractors. • In situ hydraulic conductivity test using packers can test the effectiveness of the rock melt seal, while a mine back performed from a lower level can further evaluate the recrystallized melt. • Preliminary costing indicates that a field-scale melting experiment at SURF is feasible within a Phase II Small Business Innovation Research budget while allowing sufficient budget for refining the heater design, coordinating the test program, and interpreting the results. Application of Research The rock melt sealing concept has the potential to reduce uncertainty associated with the long-term storage of nuclear waste. Preliminary efforts of this study defined the requirements of a downhole heater system capable of melting rock and indicated that developing such a system is feasible using available technology. The next logical step is designing and manufacturing prototype heaters. Concurrent with prototype development is coordinating robust field-scale experiments that are capable of validating the design for marketing to potential users.« less

Shuttle freezer conceptual design

NASA Technical Reports Server (NTRS)

Proctor, B. W.; Russell, D. J.

1975-01-01

A conceptual design for a kit freezer for operation onboard shuttle was developed. The freezer features a self-contained unit which can be mounted in the orbiter crew compartment and is capable of storing food at launch and returning with medical samples. Packaging schemes were investigated to provide the optimum storage capacity with a minimum weight and volume penalty. Several types of refrigeration systems were evaluated to select one which would offer the most efficient performance and lowest hazard of safety to the crew. Detailed performance data on the selected, Stirling cycle principled refrigeration unit were developed to validate the feasibility of its application to this freezer. Thermal analyses were performed to determine the adequacy of the thermal insulation to maintain the desired storage temperature with the design cooling capacity. Stress analyses were made to insure the design structure integrity could be maintained over the shuttle flight regime. A proposed prototype freezer development plan is presented.

Probabilistic graphs as a conceptual and computational tool in hydrology and water management

NASA Astrophysics Data System (ADS)

Schoups, Gerrit

2014-05-01

Originally developed in the fields of machine learning and artificial intelligence, probabilistic graphs constitute a general framework for modeling complex systems in the presence of uncertainty. The framework consists of three components: 1. Representation of the model as a graph (or network), with nodes depicting random variables in the model (e.g. parameters, states, etc), which are joined together by factors. Factors are local probabilistic or deterministic relations between subsets of variables, which, when multiplied together, yield the joint distribution over all variables. 2. Consistent use of probability theory for quantifying uncertainty, relying on basic rules of probability for assimilating data into the model and expressing unknown variables as a function of observations (via the posterior distribution). 3. Efficient, distributed approximation of the posterior distribution using general-purpose algorithms that exploit model structure encoded in the graph. These attributes make probabilistic graphs potentially useful as a conceptual and computational tool in hydrology and water management (and beyond). Conceptually, they can provide a common framework for existing and new probabilistic modeling approaches (e.g. by drawing inspiration from other fields of application), while computationally they can make probabilistic inference feasible in larger hydrological models. The presentation explores, via examples, some of these benefits.

Conceptual study of a 250 kW planar SOFC system for CHP application

NASA Astrophysics Data System (ADS)

Fontell, E.; Kivisaari, T.; Christiansen, N.; Hansen, J.-B.; Pålsson, J.

In August 2002, Wärtsilä Corporation and Haldor Topsøe A/S entered into a co-operation agreement to start joint development program within the planar SOFC technology. The development program aims to bring to the market highly efficient, clean and cost competitive fuel cell systems with power outputs above 200 kW for distributed power generation with CHP and for marine applications. In this study, the product concept for a 250 kW natural gas-fuelled atmospheric SOFC plant has been studied. The process has been calculated and optimised for high electrical efficiency. In the calculations, system efficiencies more than 55-85% (electrical co-generation) have been reached. The necessary balance of plant (BoP) components have been identified and the concept for grid connection has been defined. The BoP includes fuel and air supply, anode re-circulation, start-up steam, purge gas, exhaust gas heat recovery, back-up power, power electronics and control system. Based on the analysed system and component information, a conceptual design and cost break down structure for the product have been made. The cost breakdown shows that the stack, system control and power electronics are the major cost factors, while the remaining BoP equipment stands for a minor share of the manufacturing cost. Finally, the feasibility of the SOFC plants has been compared to gas engines.

Towards a computational- and algorithmic-level account of concept blending using analogies and amalgams

NASA Astrophysics Data System (ADS)

Besold, Tarek R.; Kühnberger, Kai-Uwe; Plaza, Enric

2017-10-01

Concept blending - a cognitive process which allows for the combination of certain elements (and their relations) from originally distinct conceptual spaces into a new unified space combining these previously separate elements, and enables reasoning and inference over the combination - is taken as a key element of creative thought and combinatorial creativity. In this article, we summarise our work towards the development of a computational-level and algorithmic-level account of concept blending, combining approaches from computational analogy-making and case-based reasoning (CBR). We present the theoretical background, as well as an algorithmic proposal integrating higher-order anti-unification matching and generalisation from analogy with amalgams from CBR. The feasibility of the approach is then exemplified in two case studies.

Solar Power System Analyses for Electric Propulsion Missions

NASA Technical Reports Server (NTRS)

Kerslake, Thomas W.; Gefert, Leon P.

1999-01-01

Solar electric propulsion (SEP) mission architectures are applicable to a wide range of NASA missions including human Mars exploration and robotic exploration of the outer planets. In this paper, we discuss the conceptual design and detailed performance analysis of an SEP stage electric power system (EPS). EPS performance, mass and area predictions are compared for several PV array technologies. Based on these studies, an EPS design for a 1-MW class, Human Mars Mission SEP stage was developed with a reasonable mass, 9.4 metric tons, and feasible deployed array area, 5800 sq m. An EPS was also designed for the Europa Mapper spacecraft and had a mass of 151 kg and a deployed array area of 106 sq m.

Spacecraft in switch matrix for wide band service applicatons in 30/20 GHz communications satellite systems

NASA Technical Reports Server (NTRS)

Cory, B. J.

1982-01-01

Bandwidth, switching speed, off-state isolation, and reliability over a ten-year mission were factors in determining the optimum available technology for satellite communications switching in 1982. A proof of concept model for a 20 x 20 coupled crossbar switch matrix designed with FET devices for microwave switching and with high speed CMOS LIS for switch crosspoint addressing was fabricated and tested. Results show the design is feasible for application in a multichannel SS-TDMA communications system. Expandibility can readily be achieved with this design. A conceptual design study for a 100 x 100 switch matrix utilizing a coupled crossbar architecture implemented with a monolithic microwave integrated circuits revealed technology needs for high capacity switch matrices.

Study of Systems and Technology for Liquid Hydrogen Production Independent of Fossil Fuels

NASA Technical Reports Server (NTRS)

Sprafka, R. J.; Escher, W. J. D.; Foster, R. W.; Tison, R. R.; Shingleton, J.; Moore, J. S.; Baker, C. R.

1983-01-01

Based on Kennedy Space Center siting and logistics requirements and the nonfossil energy resources at the Center, a number of applicable technologies and system candidates for hydrogen production were identified and characterized. A two stage screening of these technologies in the light of specific criteria identified two leading candidates as nonfossil system approaches. Conceptual design and costing of two solar-operated, stand alone systems, one photovoltaic based on and the other involving the power tower approach reveals their technical feasibility as sited as KSC, and the potential for product cost competitiveness with conventional supply approaches in the 1990 to 1210 time period. Conventional water hydrolysis and hydrogen liquefaction subsystems are integrated with the solar subsystems.

The Expeditionary Test Set - A fresh approach to automatic testing

NASA Astrophysics Data System (ADS)

Williams, D. L.; Austin, W. J.

This paper discusses the key design decisions and tradeoffs leading from the conceptual stage to the production version of the Expeditionary Test Set (ETS) for the USMC. This included a ten-month feasibility study program funded by the Naval Air Systems Command which culminated in the successful demonstration of a working tester model. The demonstration of the test set was preceded by a substantial re-thinking of conventional ATE test methods. Considerable discussion is devoted to the impact of test philosophy, both on the test set design and the overall effectiveness of avionic testing. Major architectural features of the test set are presented in some detail, and the many areas which break from traditional ATE design are emphasized.

Solar energy for process heat: Design/cost studies of four industrial retrofit applications

NASA Technical Reports Server (NTRS)

French, R. L.; Bartera, R. E.

1978-01-01

Five specific California plants with potentially attractive solar applications were identified in a process heat survey. These five plants were visited, process requirements evaluated, and conceptual solar system designs were generated. Four DOE (ERDA) sponsored solar energy system demonstration projects were also reviewed and compared to the design/cost cases included in this report. In four of the five cases investigated, retrofit installations providing significant amounts of thermal energy were found to be feasible. The fifth was rejected because of the condition of the building involved, but the process (soap making) appears to be an attractive potential solar application. Costs, however, tend to be high. Several potential areas for cost reduction were identified including larger collector modules and higher duty cycles.

Evaluation of a large capacity heat pump concept for active cooling of hypersonic aircraft structure

NASA Technical Reports Server (NTRS)

Pagel, L. L.; Herring, R. L.

1978-01-01

Results of engineering analyses assessing the conceptual feasibility of a large capacity heat pump for enhancing active cooling of hypersonic aircraft structure are presented. A unique heat pump arrangement which permits cooling the structure of a Mach 6 transport to aluminum temperatures without the aid of thermal shielding is described. The selected concept is compatible with the use of conventional refrigerants, with Freon R-11 selected as the preferred refrigerant. Condenser temperatures were limited to levels compatible with the use of conventional refrigerants by incorporating a unique multipass condenser design, which extracts mechanical energy from the hydrogen fuel, prior to each subsequent pass through the condenser. Results show that it is technically feasible to use a large capacity heat pump in lieu of external shielding. Additional analyses are required to optimally apply this concept.

Feasibility analysis of reciprocating magnetic heat pumps

NASA Technical Reports Server (NTRS)

Larson, A. V.; Hartley, J. G.; Shelton, S. V.; Smith, M. M.

1986-01-01

The conceptual design selected for detailed system analysis and optimization is the reciprocating gadolinium core in a regenerative fluid column within the bore of a superconducting magnet. The thermodynamic properties of gadolinium are given. A computerized literature search for relevant papers was conducted and is being analyzed. Contact was made with suppliers of superconducting magnets and accessories, magnetic materials, and various types of hardware. A description of the model for the thermal analysis of the core and regenerator fluids is included.

Land Mobile Satellite Service (LMSS): A conceptual system design and identification of the critical technologies. Part 1: Executive summary

NASA Technical Reports Server (NTRS)

Naderi, F. (Editor)

1982-01-01

A system design for a satellite aided land mobile service is described. The advanced system is based on a geostationary satellite which employs a large UHF reflector to communicate with small user antennas on mobile vehicles. It is shown that the system through multiple beam antennas and frequency reuse provides for radiotelephone and dispatch channels. It is concluded that the system is technologically feasible to provide service to rural and remote regions.

Precision magnetic suspension linear bearing

NASA Technical Reports Server (NTRS)

Trumper, David L.; Queen, Michael A.

1992-01-01

We have shown the design and analyzed the electromechanics of a linear motor suitable for independently controlling two suspension degrees of freedom. This motor, at least on paper, meets the requirements for driving an X-Y stage of 10 Kg mass with about 4 m/sq sec acceleration, with travel of several hundred millimeters in X and Y, and with reasonable power dissipation. A conceptual design for such a stage is presented. The theoretical feasibility of linear and planar bearings using single or multiple magnetic suspension linear motors is demonstrated.

Feasibility and adherence paradigm to ecological momentary assessments in urban minority youth.

PubMed

Shiyko, Mariya P; Perkins, Seth; Caldwell, Linda

2017-07-01

All adolescents in general, including ethnic and racial minorities, report high levels of cell phone use, making mobile technology a useful tool for assessment and intervention. Known health and education disparities based on minority status motivated us to conduct an in-depth investigation regarding feasibility of and adherence to the ecological momentary assessment (EMA) research protocol, studying daily life of urban minority youth. In addition, this paper presents a methodological approach to conceptualizing and reporting adherence in EMA studies. The sample was comprised of 126 youth (41.3% boys; 40.5% 7th and 59.5% 8th graders; 75.4% African American, and 20.6% Hispanic) who carried a mobile phone for 10 days, including 2 weekends and reported on activities, moods, and attitudes. Mean level of adherence was 81% for momentary and 93.8% for daily assessments; it decreased over time and was higher during the week compared to weekends. Adherence was lower on days when participants reported high levels of negative affect and on days when they were engaged in physical activities. Our findings underscore the importance of differentiating between human and technology-related factors when computing adherence rates and portray adherence as a complex and dynamic construct that can vary across individuals. Specific study recommendations and methodological discussion provide guidelines for designing future studies. (PsycINFO Database Record (c) 2017 APA, all rights reserved).

Monitoring Natural World Heritage Sites: optimization of the monitoring system in Bogda with GIS-based multi-criteria decision analysis.

PubMed

Wang, Zhaoguo; Du, Xishihui

2016-07-01

Natural World Heritage Sites (NWHSs) are invaluable treasure due to the uniqueness of each site. Proper monitoring and management can guarantee their protection from multiple threats. In this study, geographic information system (GIS)-based multi-criteria decision analysis (GIS-MCDA) was used to assess criteria layers acquired from the data available in the literature. A conceptual model for determining the priority area for monitoring in Bogda, China, was created based on outstanding universal values (OUV) and expert knowledge. Weights were assigned to each layer using the analytic hierarchy process (AHP) based on group decisions, encompassing three experts: one being a heritage site expert, another a forest ranger, and the other a heritage site manager. Subsequently, evaluation layers and constraint layers were used to generate a priority map and to determine the feasibility of monitoring in Bogda. Finally, a monitoring suitability map of Bogda was obtained by referencing priority and feasibility maps.The high-priority monitoring area is located in the montane forest belt, which exhibits high biodiversity and is the main tourist area of Bogda. The northern buffer zone of Bogda comprises the concentrated feasible monitoring areas, and the area closest to roads and monitoring facilities is highly feasible for NWHS monitoring. The suitability of an area in terms of monitoring is largely determined by the monitoring priority in that particular area. The majority of planned monitoring facilities are well distributed in both suitable and less suitable areas. Analysis results indicate that the protection of Bogda will be more scientifically based due to its effective and all-around planned monitoring system proposed by the declaration text of Xinjiang Tianshan, which is the essential file submitted to World Heritage Centre to inscribe as a NWHS.

A single competency-based education and training and competency-based career framework for the Australian health workforce: discussing the potential value add.

PubMed

Brownie, Sharon Mary; Thomas, Janelle

2014-09-01

This brief discusses the policy implications of a research study commissioned by Health Workforce Australia (HWA) within its health workforce innovation and reform work program. The project explored conceptually complex and operationally problematic concepts related to developing a whole-of-workforce competency-based education and training and competency-based career framework for the Australian health workforce and culminated with the production of three reports published by HWA. The project raised important queries as to whether such a concept is desirable, feasible or implementable - in short what is the potential value add and is it achievable? In setting the scene for discussion, the foundation of the project's genesis and focus of the study are highlighted. A summary of key definitions related to competency-based education and training frameworks and competency-based career frameworks are provided to further readers' commonality of understanding. The nature of the problem to be solved is explored and the potential value-add for the Australian health workforce and its key constituents proposed. The paper concludes by discussing relevance and feasibility issues within Australia's current and changing healthcare context along with the essential steps and implementation realities that would need to be considered and actioned if whole-of-workforce frameworks were to be developed and implemented.

From Qualitative Work to Intervention Development in Pediatric Oncology Palliative Care Research

PubMed Central

Gilmer, Mary Jo; Friedman, Debra L.; Given, Barbara; Hendricks-Ferguson, Verna L.; Hinds, Pamela S.

2013-01-01

Qualitative methods can be particularly useful approaches to use with individuals who are experiencing a rare disease and thus who comprise a small sample (such as children with cancer) and are at points in care that few experience (such as end of life). This data-based methods article describes how findings from a qualitative study were used to guide and shape a pediatric oncology palliative care intervention. Qualitative data can lay a strong foundation for subsequent pilot intervention work by facilitating the development of an underlying study conceptualization, providing recruitment feasibility estimates, helping establish clinically meaningful inclusion criteria, establishing staff acceptability of a research intervention, and providing support for face validity of newly developed interventions. These benefits of preliminary qualitative research are described in the context of this study on legacy-making, which involves reports of children (7-12 years of age) living with advanced cancer and of their parent caregivers. PMID:23632900

Feasibility study of a swept frequency electromagnetic probe (SWEEP) using inductive coupling for the determination of subsurface conductivity of the earth and water prospecting in arid regions

NASA Technical Reports Server (NTRS)

Latorraca, G. A.; Bannister, L. H.

1974-01-01

Techniques developed for electromagnetic probing of the lunar interior, and techniques developed for the generation of high power audio frequencies were combined to make practical a magnetic inductive coupling system for the rapid measurement of ground conductivity profiles which are helpful when prospecting for the presence and quality of subsurface water. A system which involves the measurement of the direction, intensity, and time phase of the magnetic field observed near the surface of the earth at a distance from a horizontal coil energized so as to create a field that penetrates the earth was designed and studied to deduce the conductivity and stratification of the subsurface. Theoretical studies and a rudimentary experiment in an arid region showed that the approach is conceptually valid and that this geophysical prospecting technique can be developed for the economical exploration of subterranean water resources.

A conceptual model of the automated credibility assessment of the volunteered geographic information

NASA Astrophysics Data System (ADS)

Idris, N. H.; Jackson, M. J.; Ishak, M. H. I.

2014-02-01

The use of Volunteered Geographic Information (VGI) in collecting, sharing and disseminating geospatially referenced information on the Web is increasingly common. The potentials of this localized and collective information have been seen to complement the maintenance process of authoritative mapping data sources and in realizing the development of Digital Earth. The main barrier to the use of this data in supporting this bottom up approach is the credibility (trust), completeness, accuracy, and quality of both the data input and outputs generated. The only feasible approach to assess these data is by relying on an automated process. This paper describes a conceptual model of indicators (parameters) and practical approaches to automated assess the credibility of information contributed through the VGI including map mashups, Geo Web and crowd - sourced based applications. There are two main components proposed to be assessed in the conceptual model - metadata and data. The metadata component comprises the indicator of the hosting (websites) and the sources of data / information. The data component comprises the indicators to assess absolute and relative data positioning, attribute, thematic, temporal and geometric correctness and consistency. This paper suggests approaches to assess the components. To assess the metadata component, automated text categorization using supervised machine learning is proposed. To assess the correctness and consistency in the data component, we suggest a matching validation approach using the current emerging technologies from Linked Data infrastructures and using third party reviews validation. This study contributes to the research domain that focuses on the credibility, trust and quality issues of data contributed by web citizen providers.

Intervention complexity--a conceptual framework to inform priority-setting in health.

PubMed Central

Gericke, Christian A.; Kurowski, Christoph; Ranson, M. Kent; Mills, Anne

2005-01-01

Health interventions vary substantially in the degree of effort required to implement them. To some extent this is apparent in their financial cost, but the nature and availability of non-financial resources is often of similar importance. In particular, human resource requirements are frequently a major constraint. We propose a conceptual framework for the analysis of interventions according to their degree of technical complexity; this complements the notion of institutional capacity in considering the feasibility of implementing an intervention. Interventions are categorized into four dimensions: characteristics of the basic intervention; characteristics of delivery; requirements on government capacity; and usage characteristics. The analysis of intervention complexity should lead to a better understanding of supply- and demand-side constraints to scaling up, indicate priorities for further research and development, and can point to potential areas for improvement of specific aspects of each intervention to close the gap between the complexity of an intervention and the capacity to implement it. The framework is illustrated using the examples of scaling up condom social marketing programmes, and the DOTS strategy for tuberculosis control in highly resource-constrained countries. The framework could be used as a tool for policy-makers, planners and programme managers when considering the expansion of existing projects or the introduction of new interventions. Intervention complexity thus complements the considerations of burden of disease, cost-effectiveness, affordability and political feasibility in health policy decision-making. Reducing the technical complexity of interventions will be crucial to meeting the health-related Millennium Development Goals. PMID:15868020

Intervention complexity--a conceptual framework to inform priority-setting in health.

PubMed

Gericke, Christian A; Kurowski, Christoph; Ranson, M Kent; Mills, Anne

2005-04-01

Health interventions vary substantially in the degree of effort required to implement them. To some extent this is apparent in their financial cost, but the nature and availability of non-financial resources is often of similar importance. In particular, human resource requirements are frequently a major constraint. We propose a conceptual framework for the analysis of interventions according to their degree of technical complexity; this complements the notion of institutional capacity in considering the feasibility of implementing an intervention. Interventions are categorized into four dimensions: characteristics of the basic intervention; characteristics of delivery; requirements on government capacity; and usage characteristics. The analysis of intervention complexity should lead to a better understanding of supply- and demand-side constraints to scaling up, indicate priorities for further research and development, and can point to potential areas for improvement of specific aspects of each intervention to close the gap between the complexity of an intervention and the capacity to implement it. The framework is illustrated using the examples of scaling up condom social marketing programmes, and the DOTS strategy for tuberculosis control in highly resource-constrained countries. The framework could be used as a tool for policy-makers, planners and programme managers when considering the expansion of existing projects or the introduction of new interventions. Intervention complexity thus complements the considerations of burden of disease, cost-effectiveness, affordability and political feasibility in health policy decision-making. Reducing the technical complexity of interventions will be crucial to meeting the health-related Millennium Development Goals.

Funding and remuneration of interdisciplinary primary care teams in Canada: a conceptual framework and application.

PubMed

Wranik, W Dominika; Haydt, Susan M; Katz, Alan; Levy, Adrian R; Korchagina, Maryna; Edwards, Jeanette M; Bower, Ian

2017-05-15

Reliance on interdisciplinary teams in the delivery of primary care is on the rise. Funding bodies strive to design financial environments that support collaboration between providers. At present, the design of financial arrangements has been fragmented and not based on evidence. The root of the problem is a lack of systematic evidence demonstrating the superiority of any particular financial arrangement, or a solid understanding of options. In this study we develop a framework for the conceptualization and analysis of financial arrangements in interdisciplinary primary care teams. We use qualitative data from three sources: (i) interviews with 19 primary care decision makers representing 215 clinics in three Canadian provinces, (ii) a research roundtable with 14 primary care decision makers and/or researchers, and (iii) policy documents. Transcripts from interviews and the roundtable were coded thematically and a framework synthesis approach was applied. Our conceptual framework differentiates between team level funding and provider level remuneration, and characterizes the interplay and consonance between them. Particularly the notions of hierarchy, segregation, and dependence of provider incomes, and the link between funding and team activities are introduced as new clarifying concepts, and their implications explored. The framework is applied to the analysis of collaboration incentives, which appear strongest when provider incomes are interdependent, funding is linked to the team as a whole, and accountability does not have multiple lines. Emergent implementation issues discussed by respondents include: (i) centrality of budget negotiations; (ii) approaches to patient rostering; (iii) unclear funding sources for space and equipment; and (iv) challenges with community engagement. The creation of patient rosters is perceived as a surprisingly contentious issue, and the challenges of funding for space and equipment remain unresolved. The development and application of a conceptual framework is an important step to the systematic study of the best performing financial models in the context of interdisciplinary primary care. The identification of optimal financial arrangements must be contextualized in terms of feasibility and the implementation environment. In general, financial hierarchy, both overt and covert, is considered a barrier to collaboration.

Georgetown University Integrated Community Energy System (GU-ICES). Phase III, Stage I. Feasibility analysis. Final report. Volume 1

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

This Feasibility Analysis covers a wide range of studies and evaluations. The Report is divided into five parts. Section 1 contains all material relating to the Institutional Assessment including consideration of the requirements and position of the Potomac Electric Co. as they relate to cogeneration at Georgetown in parallel with the utility (Task 1). Sections 2 through 7 contain all technical information relating to the Alternative Subsystems Analysis (Task 4). This includes the energy demand profiles upon which the evaluations were based (Task 3). It further includes the results of the Life-Cycle-Cost Analyses (Task 5) which are developed in detailmore » in the Appendix for evaluation in the Technical Report. Also included is the material relating to Incremental Savings and Optimization (Task 6) and the Conceptual Design for candidate alternate subsystems (Task 7). Section 8 contains all material relating to the Environmental Impact Assessment (Task 2). The Appendix contains supplementary material including the budget cost estimates used in the life-cycle-cost analyses, the basic assumptions upon which the life-cycle analyses were developed, and the detailed life-cycle-cost anlysis for each subsystem considered in detail.« less

Feasibility study of a cyclotron complex for hadron therapy

NASA Astrophysics Data System (ADS)

Smirnov, V.; Vorozhtsov, S.

2018-04-01

An accelerator complex for hadron therapy based on a chain of cyclotrons is under development at JINR (Dubna, Russia), and the corresponding conceptual design is under preparation. The complex mainly consists of two superconducting cyclotrons. The first accelerator is a compact cyclotron used as an injector to the main accelerator, which is a six-fold separated sector machine. The facility is intended for generation of protons and carbon beams. The H2+ and 12C6+ ions from the corresponding ECR ion sources are accelerated in the injector-cyclotron up to the output energy of 70 MeV/u. Then, the H2+ ions are extracted from the injector by a stripping foil, and the resulting proton beam with the energy of 70 MeV is used for medical purposes. After acceleration in the main cyclotron, the carbon beam can be either used directly for therapy or introduced to the main cyclotron for obtaining the final energy of 400 MeV/u. The basic requirements to the project are the following: compliance to medical requirements, compact size, feasible design, and high reliability of all systems of the complex. The advantages of the dual cyclotron design can help reaching these goals. The initial calculations show that this design is technically feasible with acceptable beam dynamics. The accelerator complex with a relatively compact size can be a good solution for medical applications. The basic parameters of the facility and detailed investigation of the magnetic system and beam dynamics are described.

Feasibility of Tidal and Ocean Current Energy in False Pass, Aleutian Islands, Alaska final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wright, Bruce Albert

The Aleutian Pribilof Islands Association was awarded a U.S. Department of Energy Tribal Energy Program grant (DE-EE0005624) for the Feasibility of Tidal and Ocean Current Energy in False Pass, Aleutian Islands, Alaska (Project). The goal of the Project was to perform a feasibility study to determine if a tidal energy project would be a viable means to generate electricity and heat to meet long-term fossil fuel use reduction goals, specifically to produce at least 30% of the electrical and heating needs of the tribally-owned buildings in False Pass. The Project Team included the Aleut Region organizations comprised of the Aleutianmore » Pribilof Island Association (APIA), and Aleutian Pribilof Island Community Development Association (APICDA); the University of Alaska Anchorage, ORPC Alaska a wholly-owned subsidiary of Ocean Renewable Power Company (ORPC), City of False Pass, Benthic GeoScience, and the National Renewable Energy Laboratory (NREL). The following Project objectives were completed: collected existing bathymetric, tidal, and ocean current data to develop a basic model of current circulation at False Pass, measured current velocities at two sites for a full lunar cycle to establish the viability of the current resource, collected data on transmission infrastructure, electrical loads, and electrical generation at False Pass, performed economic analysis based on current costs of energy and amount of energy anticipated from and costs associated with the tidal energy project conceptual design and scoped environmental issues. Utilizing circulation modeling, the Project Team identified two target sites with strong potential for robust tidal energy resources in Isanotski Strait and another nearer the City of False Pass. In addition, the Project Team completed a survey of the electrical infrastructure, which identified likely sites of interconnection and clarified required transmission distances from the tidal energy resources. Based on resource and electrical data, the Project Team developed a conceptual tidal energy project design utilizing ORPC’s TidGen® Power System. While the Project Team has not committed to ORPC technology for future development of a False Pass project, this conceptual design was critical to informing the Project’s economic analysis. The results showed that power from a tidal energy project could be provided to the City of False at a rate at or below the cost of diesel generated electricity and sold to commercial customers at rates competitive with current market rates, providing a stable, flat priced, environmentally sound alternative to the diesel generation currently utilized for energy in the community. The Project Team concluded that with additional grants and private investment a tidal energy project at False Pass is well-positioned to be the first tidal energy project to be developed in Alaska, and the first tidal energy project to be interconnected to an isolated micro grid in the world. A viable project will be a model for similar projects in coastal Alaska.« less

Planetary benchmarks. [structural design criteria for radar reference devices on planetary surfaces

NASA Technical Reports Server (NTRS)

Uphoff, C.; Staehle, R.; Kobrick, M.; Jurgens, R.; Price, H.; Slade, M.; Sonnabend, D.

1978-01-01

Design criteria and technology requirements for a system of radar reference devices to be fixed to the surfaces of the inner planets are discussed. Offshoot applications include the use of radar corner reflectors as landing beacons on the planetary surfaces and some deep space applications that may yield a greatly enhanced knowledge of the gravitational and electromagnetic structure of the solar system. Passive retroreflectors with dimensions of about 4 meters and weighing about 10 kg are feasible for use with orbiting radar at Venus and Mars. Earth-based observation of passive reflectors, however, would require very large and complex structures to be delivered to the surfaces. For Earth-based measurements, surface transponders offer a distinct advantage in accuracy over passive reflectors. A conceptual design for a high temperature transponder is presented. The design appears feasible for the Venus surface using existing electronics and power components.

Advanced Earth Observation System Instrumentation Study (AEOSIS)

NASA Technical Reports Server (NTRS)

Var, R. E.

1976-01-01

The feasibility, practicality, and cost are investigated for establishing a national system or grid of artificial landmarks suitable for automated (near real time) recognition in the multispectral scanner imagery data from an earth observation satellite (EOS). The intended use of such landmarks, for orbit determination and improved mapping accuracy is reviewed. The desirability of using xenon searchlight landmarks for this purpose is explored theoretically and by means of experimental results obtained with LANDSAT 1 and LANDSAT 2. These results are used, in conjunction with the demonstrated efficiency of an automated detection scheme, to determine the size and cost of a xenon searchlight that would be suitable for an EOS Searchlight Landmark Station (SLS), and to facilitate the development of a conceptual design for an automated and environmentally protected EOS SLS.

A conceptual design study of a high temperature solar thermal receiver (added tasks 6 and 7)

NASA Technical Reports Server (NTRS)

Robertson, C. S.; Mccreight, L. R.; Gatti, A.; Semon, H. W.

1980-01-01

The key component of this concept is a coiled tube of silicon nitride which acts as a heat exchanger appears to be ideal from the standpoint of utilizing structural ceramics at around 2500 F under severe thermal shock conditions. However the size and configuration of this coil are beyond the state of the art for fabricating such materials as silicon nitride and carbide. A two-task program to develop and demonstrate the feasibility of extruding and forming a section of thin walled silicon nitride tubing was undertaken as an addition to the original program. A promising polyvinyl butyral-based binder lubricant was identified. Fourteen full size extrusion experiments were conducted. Two trial firings of 1-1/4 turn helices were made.

Conceptual/preliminary design study of subsonic v/stol and stovl aircraft derivatives of the S-3A

NASA Technical Reports Server (NTRS)

Kidwell, G. H., Jr.

1981-01-01

A computerized aircraft synthesis program was used to examine the feasibility and capability of a V/STOL aircraft based on the Navy S-3A aircraft. Two major airframe modifications are considered: replacement of the wing, and substitution of deflected thrust turbofan engines similar to the Pegasus engine. Three planform configurations for the all composite wing were investigated: an unconstrained span design, a design with the span constrained to 64 feet, and an unconstrained span oblique wing design. Each design was optimized using the same design variables, and performance and control analyses were performed. The oblique wing configuration was found to have the greatest potential in this application. The mission performance of these V/STOL aircraft compares favorably with that of the CTOL S-3A.

Modeling and analysis of power processing systems: Feasibility investigation and formulation of a methodology

NASA Technical Reports Server (NTRS)

Biess, J. J.; Yu, Y.; Middlebrook, R. D.; Schoenfeld, A. D.

1974-01-01

A review is given of future power processing systems planned for the next 20 years, and the state-of-the-art of power processing design modeling and analysis techniques used to optimize power processing systems. A methodology of modeling and analysis of power processing equipment and systems has been formulated to fulfill future tradeoff studies and optimization requirements. Computer techniques were applied to simulate power processor performance and to optimize the design of power processing equipment. A program plan to systematically develop and apply the tools for power processing systems modeling and analysis is presented so that meaningful results can be obtained each year to aid the power processing system engineer and power processing equipment circuit designers in their conceptual and detail design and analysis tasks.

The origin of life: a problem of history, chemistry, and evolution.

PubMed

Ma, Wentao

2014-12-01

The origin of life is a field full of controversies, not only because of our vague understanding concerning the relevant issues, but also, perhaps more often, owing to our dim conceptual framework throughout the whole field. To improve this situation, an in-depth conceptual dissection is presented here. It is elucidated that, at its core, the origin of life has three aspects. The facts involved in the process are taken as the historical aspect, which is destined to be uncertain and often irrelevant to debate regarding details. The rules involved include two distinct aspects: chemical mechanisms operated in the whole process, while evolutionary mechanisms joined in only after the emergence of the first Darwinian entities - and then accounted for the subsequent buildup of complexity (this cannot be explained solely by natural selection). Basically, we can ask about the possibility of any assumed event in the origin of life: 'Is it evolutionarily plausible, chemically feasible, and historically likely?' Clues from any of the three aspects may be quite valuable in directing our explorations on the other two. This conceptual dissection provides a clearer context for the field, which may even be more useful than any sort of specific research. Copyright © 2014 Verlag Helvetica Chimica Acta AG, Zürich.

"Suffering" in palliative sedation: Conceptual Analysis and Implications for Decision-Making in Clinical Practice.

PubMed

Bozzaro, Claudia; Schildmann, Jan

2018-04-21

Palliative sedation is an increasingly used and, simultaneously, challenging practice at the end of life. Many controversies associated with this therapy are rooted in implicit differences regarding the understanding of "suffering" as prerequisite for palliative sedation. The aim of this paper is to inform the current debates by a conceptual analysis of two different philosophical accounts of suffering, (1) the subjective and holistic concept and (2) the objective and gradual concept and by a clinical-ethical analysis of the implications of each account for decisions about palliative sedation. We will show that while the subjective and holistic account of suffering fits well with the holistic approach of palliative care, there are considerable challenges to justify limits to requests for palliative sedation. By contrast, the objective and gradual account fits well with the need for an objective basis for clinical decisions in the context of palliative sedation, but runs the risk of falling short when considering the individual and subjective experience of suffering at the end of life. We will conclude with a plea for the necessity of further combined conceptual and empirical research to develop a sound and feasible understanding of suffering which can contribute to consistent decision-making about palliative sedation. Copyright © 2018. Published by Elsevier Inc.

Global feasibility assessment of interrupting the transmission of soil-transmitted helminths: a statistical modelling study.

PubMed

Brooker, Simon J; Nikolay, Birgit; Balabanova, Dina; Pullan, Rachel L

2015-08-01

Emphasis is being given to the control of neglected tropical diseases, including the possibility of interrupting the transmission of soil-transmitted helminths (STH). We evaluated the feasibility by country of achieving interruption of the transmission of STH. Based on a conceptual framework for the identification of the characteristics of a successful STH control programme, we assembled spatial data for a range of epidemiological, institutional, economic, and political factors. Using four different statistical methods, we developed a composite score of the feasibility of interrupting STH transmission and undertook a sensitivity analysis of the data and methods. The most important determining factors in the analysis were underlying intensity of STH transmission, current implementation of control programmes for neglected tropical diseases, and whether countries receive large-scale external funding and have strong health systems. The composite scores suggested that interrupting STH transmission is most feasible in countries in the Americas and parts of Asia (eg, Argentina [range of composite feasibility scores, depending on scoring method, 9·4-10·0], Brazil [8·7- 9·7], Chile [8·84-10·0], and Thailand [9·1-10·0]; there was perfect agreement between the four methods), and least feasible in countries in sub-Saharan Africa (eg, Congo [0·4-2·7] and Guinea [2·0-5·6]; there was full agreement between methods), but there were important exceptions to these trends (eg, Ghana [7·4-10·0]; there was agreement between three methods). Agreement was highest between the scores derived with the expert opinion and principal component analysis weighting schemes (Pearson correlation coefficient, r=0·98). The largest disagreement was between benefit-of-the-doubt-derived and principal-component-analysis-derived weighting schemes (r=0·74). The interruption of STH transmission is feasible, especially in countries with low intensity of transmission, supportive household environments, strong health systems, and the availability of suitable delivery platforms and in-country funds, but to achieve local elimination of STH an intersectoral approach to STH control will be needed. Bill & Melinda Gates Foundation and Wellcome Trust. Copyright © 2015 Brooker et al. Open Access article distributed under the terms of CC BY-NC-ND. Published by Elsevier Ltd.. All rights reserved.

Evaluation of thermal energy storage for the proposed Twin Cities District Heating system. [using cogeneration heat production and aquifiers for heat storage

NASA Technical Reports Server (NTRS)

Meyer, C. F.

1980-01-01

The technical and economic feasibility of incorporating thermal energy storage components into the proposed Twin Cities District heating project was evaluated. The technical status of the project is reviewed and conceptual designs of district heating systems with and without thermal energy storage were compared in terms of estimated capital requirements, fuel consumption, delivered energy cost, and environmental aspects. The thermal energy storage system is based on cogeneration and the storage of heat in aquifers.

Spacecraft Conceptual Design for Returning Entire Near-Earth Asteroids

NASA Technical Reports Server (NTRS)

Brophy, John R.; Oleson, Steve

2012-01-01

In situ resource utilization (ISRU) in general, and asteroid mining in particular are ideas that have been around for a long time, and for good reason. It is clear that ultimately human exploration beyond low-Earth orbit will have to utilize the material resources available in space. Historically, the lack of sufficiently capable in-space transportation has been one of the key impediments to the harvesting of near-Earth asteroid resources. With the advent of high-power (or order 40 kW) solar electric propulsion systems, that impediment is being removed. High-power solar electric propulsion (SEP) would be enabling for the exploitation of asteroid resources. The design of a 40-kW end-of-life SEP system is presented that could rendezvous with, capture, and subsequently transport a 1,000-metric-ton near-Earth asteroid back to cislunar space. The conceptual spacecraft design was developed by the Collaborative Modeling for Parametric Assessment of Space Systems (COMPASS) team at the Glenn Research Center in collaboration with the Keck Institute for Space Studies (KISS) team assembled to investigate the feasibility of an asteroid retrieval mission. Returning such an object to cislunar space would enable astronaut crews to inspect, sample, dissect, and ultimately determine how to extract the desired materials from the asteroid. This process could jump-start the entire ISRU industry.

Measurement Tools for Integrated Worker Health Protection and Promotion: Lessons Learned From the SafeWell Project.

PubMed

Pronk, Nicolaas P; McLellan, Deborah L; McGrail, Michael P; Olson, Shawn M; McKinney, Zeke J; Katz, Jeffrey N; Wagner, Gregory R; Sorensen, Glorian

2016-07-01

To describe (a) a conceptual approach, (b) measurement tools and data collection processes, (c) characteristics of an integrated feedback report and action plan, and (d) experiences of three companies with an integrated measurement approach to worker safety and health. Three companies implemented measurement tools designed to create an integrated view of health protection and promotion based on organizational- and individual-level assessments. Feedback and recommended actions were presented following assessments at baseline and 1-year follow-up. Measurement processes included group dialogue sessions, walk-through, online surveys, and focus groups. The approach and measurement tools generated actionable recommendations and documented changes in the physical (eg, safety hazards) and psychosocial (eg, health and safety culture) work environment between baseline and 1-year follow-up. The measurement tools studied were feasible, acceptable, and meaningful to companies in the SafeWell study.

A nuclear driven metallic vapor MHD coupled with MPD thrusters

NASA Technical Reports Server (NTRS)

Anghaie, Samim; Kumar, Ratan

1991-01-01

Nuclear energy as a source of power for space missions, represents an enabling technology for advanced and ambitious space applications. Nuclear fuel in a gaseous or liquid form has been configured as a promising and practical candidate in this regard. The present study investigates and performs a feasibility analysis of an innovative concept for space power generation and propulsion. The system embodies a conceptual nuclear reactor with an MHD generator and coupled to MPD thrusters. The reactor utilizes liquid uranium in droplet form as fuel and superheated metallic vapor as the working fluid. This ultrahigh temperature vapor core reactor brings forward varied and challenging technical issues, and it has been addressed to in this paper. A parametric study of the conceived system has been performed in a qualitative and quantitative manner. Preliminary results show enough promise for further indepth analysis of this novel system.

Multisite formative assessment for the Pathways study to prevent obesity in American Indian schoolchildren123

PubMed Central

Gittelsohn, Joel; Evans, Marguerite; Story, Mary; Davis, Sally M; Metcalfe, Lauve; Helitzer, Deborah L; Clay, Theresa E

2016-01-01

We describe the formative assessment process, using an approach based on social learning theory, for the development of a school-based obesity-prevention intervention into which cultural perspectives are integrated. The feasibility phase of the Pathways study was conducted in multiple settings in 6 American Indian nations. The Pathways formative assessment collected both qualitative and quantitative data. The qualitative data identified key social and environmental issues and enabled local people to express their own needs and views. The quantitative, structured data permitted comparison across sites. Both types of data were integrated by using a conceptual and procedural model. The formative assessment results were used to identify and rank the behavioral risk factors that were to become the focus of the Pathways intervention and to provide guidance on developing common intervention strategies that would be culturally appropriate and acceptable to all sites. PMID:10195601

A Multi-TeV Linear Collider Based on CLIC Technology : CLIC Conceptual Design Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Aicheler, M; Burrows, P.; Draper, M.

This report describes the accelerator studies for a future multi-TeV e +e - collider based on the Compact Linear Collider (CLIC) technology. The CLIC concept as described in the report is based on high gradient normal-conducting accelerating structures where the RF power for the acceleration of the colliding beams is extracted from a high-current Drive Beam that runs parallel with the main linac. The focus of CLIC R&D over the last years has been on addressing a set of key feasibility issues that are essential for proving the fundamental validity of the CLIC concept. The status of these feasibility studiesmore » are described and summarized. The report also includes a technical description of the accelerator components and R&D to develop the most important parts and methods, as well as a description of the civil engineering and technical services associated with the installation. Several larger system tests have been performed to validate the two-beam scheme, and of particular importance are the results from the CLIC test facility at CERN (CTF3). Both the machine and detector/physics studies for CLIC have primarily focused on the 3 TeV implementation of CLIC as a benchmark for the CLIC feasibility. This report also includes specific studies for an initial 500 GeV machine, and some discussion of possible intermediate energy stages. The performance and operation issues related to operation at reduced energy compared to the nominal, and considerations of a staged construction program are included in the final part of the report. The CLIC accelerator study is organized as an international collaboration with 43 partners in 22 countries. An associated report describes the physics potential and experiments at CLIC and a shorter report in preparation will focus on the CLIC implementation strategy, together with a plan for the CLIC R&D studies 2012–2016. Critical and important implementation issues such as cost, power and schedule will be addressed there.« less

The Step approach to Message Design and Testing (SatMDT): A conceptual framework to guide the development and evaluation of persuasive health messages.

PubMed

Lewis, Ioni; Watson, Barry; White, Katherine M

2016-12-01

This paper provides an important and timely overview of a conceptual framework designed to assist with the development of message content, as well as the evaluation, of persuasive health messages. While an earlier version of this framework was presented in a prior publication by the authors in 2009, important refinements to the framework have seen it evolve in recent years, warranting the need for an updated review. This paper outlines the Step approach to Message Design and Testing (or SatMDT) in accordance with the theoretical evidence which underpins, as well as empirical evidence which demonstrates the relevance and feasibility of, each of the framework's steps. The development and testing of the framework have thus far been based exclusively within the road safety advertising context; however, the view expressed herein is that the framework may have broader appeal and application to the health persuasion context. Copyright © 2015 Elsevier Ltd. All rights reserved.

Inertial Energy Storage for Spacecraft

NASA Technical Reports Server (NTRS)

Rodriguez, G. E.

1984-01-01

The feasibility of inertial energy storage in a spacecraft power system is evaluated on the basis of a conceptual integrated design that encompasses a composite rotor, magnetic suspension and a permanent magnet (PM) motor/generator for a 3-kW orbital average payload at a bus distribution voltage of 250 volts dc. The conceptual design, is referred to as a Mechanical Capacitor. The baseline power system configuration selected is a series system employing peak-power-tracking for a Low Earth-Orbiting application. Power processing, required in the motor/generator, provides potential alternative that can only be achieved in systems with electrochemical energy storage by the addition of power processing components. One such alternative configuration provides for peak-power-tracking of the solar array and still maintains a regulated bus, without the expense of additional power processing components. Precise speed control of the two counterrotating wheels is required to reduce interaction with the attitude control system (ACS) or alternatively, used to perform attitude control functions.

Conceptual design of a data reduction system

NASA Technical Reports Server (NTRS)

1983-01-01

A telemetry data processing system was defined of the Data Reduction. Data reduction activities in support of the developmental flights of the Space Shuttle were used as references against which requirements are assessed in general terms. A conceptual system design believed to offer significant throughput for the anticipated types of data reduction activities is presented. The design identifies the use of a large, intermediate data store as a key element in a complex of high speed, single purpose processors, each of which performs predesignated, repetitive operations on either raw or partially processed data. The recommended approach to implement the design concept is to adopt an established interface standard and rely heavily on mature or promising technologies which are considered main stream of the integrated circuit industry. The design system concept, is believed to be implementable without reliance on exotic devices and/or operational procedures. Numerical methods were employed to examine the feasibility of digital discrimination of FDM composite signals, and of eliminating line frequency noises in data measurements.

Process Design and Economics for the Conversion of Lignocellulosic Biomass to Hydrocarbon Fuels. Thermochemical Research Pathways with In Situ and Ex Situ Upgrading of Fast Pyrolysis Vapors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dutta, Abhijit; Sahir, Asad; Tan, Eric

This report was developed as part of the U.S. Department of Energy’s Bioenergy Technologies Office’s efforts to enable the development of technologies for the production of infrastructurecompatible, cost-competitive liquid hydrocarbon fuels from biomass. Specifically, this report details two conceptual designs based on projected product yields and quality improvements via catalyst development and process integration. It is expected that these research improvements will be made within the 2022 timeframe. The two conversion pathways detailed are (1) in situ and (2) ex situ upgrading of vapors produced from the fast pyrolysis of biomass. While the base case conceptual designs and underlying assumptionsmore » outline performance metrics for feasibility, it should be noted that these are only two of many other possibilities in this area of research. Other promising process design options emerging from the research will be considered for future techno-economic analysis.« less

Deep sulcal landmarks: algorithmic and conceptual improvements in the definition and extraction of sulcal pits.

PubMed

Auzias, G; Brun, L; Deruelle, C; Coulon, O

2015-05-01

Recent interest has been growing concerning points of maximum depth within folds, the sulcal pits, that can be used as reliable cortical landmarks. These remarkable points on the cortical surface are defined algorithmically as the outcome of an automatic extraction procedure. The influence of several crucial parameters of the reference technique (Im et al., 2010) has not been evaluated extensively, and no optimization procedure has been proposed so far. Designing an appropriate optimization framework for these parameters is mandatory to guarantee the reproducibility of results across studies and to ensure the feasibility of sulcal pit extraction and analysis on large cohorts. In this work, we propose a framework specifically dedicated to the optimization of the parameters of the method. This optimization framework relies on new measures for better quantifying the reproducibility of the number of sulcal pits per region across individuals, in line with the assumptions of one-to-one correspondence of sulcal roots across individuals which is an explicit aspect of the sulcal roots model (Régis et al., 2005). Our procedure benefits from a combination of improvements, including the use of a convenient sulcal depth estimation and is methodologically sound. Our experiments on two different groups of individuals, with a total of 137 subjects, show an increased reliability across subjects in deeper sulcal pits, as compared to the previous approach, and cover the entire cortical surface, including shallower and more variable folds that were not considered before. The effectiveness of our method ensures the feasibility of a systematic study of sulcal pits on large cohorts. On top of these methodological advances, we quantify the relationship between the reproducibility of the number of sulcal pits per region across individuals and their respective depth and demonstrate the relatively high reproducibility of several pits corresponding to shallower folds. Finally, we report new results regarding the local pit asymmetry, providing evidence that the algorithmic and conceptual approach defended here may contribute to better understanding of the key role of sulcal pits in neuroanatomy. Copyright © 2015 Elsevier Inc. All rights reserved.

Hanson Russian River Ponds floodplain restoration: Feasibility study and conceptual design; Appendix G: Physical evaluation of the restoration alternatives

USGS Publications Warehouse

McDonald, Richard R.; Nelson, Jonathan M.

2016-01-01

Appendix G: Hanson Russian River Ponds Floodplain Restoration: Feasibility Study and Conceptual Design |G-1Appendix GPhysical Evaluation of the Restoration AlternativesRichard McDonald and Jonathan Nelson, PhDU.S. Geological Survey Geomorphology and Sediment Transport Laboratory, Golden, ColoradoIntroductionTo assess the relative and overall impacts of the scenarios proposed in Chapters 7 and 9,(Stage I-A–I-D and Stage II-A –II-E), each of the topographic configurations were evaluated over a range of flows. Thisevaluation was carried out using computational flow modeling tools available in the iRIC public-domain river modeling interface (www.i-ric.org, Nelsonet al.in press). Using the iRIC modeling tools described in more detail below, basic hydraulic computations of water-surface elevation, velocity, shear stress, and other hydraulic variables were carried out for the alternatives in the reach surrounding the project area, from the confluence of Dry Creek upstream to the Wohler road bridge downstream, for the full range of observed flows. This methodology allows comparison of the current channel configuration with the proposed alternatives in terms of inundation period and frequency, depth, water velocity, and other hydraulic information. By integrating this kind of information over the reach of interest and the flow record, critical metrics assessing the impacts of various topographic modifications can be compared to those same metrics for the existing condition or other modification scenarios. In addition, because the iRIC tools include predictions of sediment mobility, suspension of fines, and the potential evolution of the land surface in response to flow, these methods provide evaluation of sediment transport, stability of current and proposed surfaces, and evaluation of how these surfaces might evolve into the future. This hydraulic and sediment transport information is critically important for understanding theimpacts of various proposed alternatives on the physical system; perhaps even more importantly given the objectives of the proposed restoration, this information can be related to biological impacts, as is discussed in subsequent chapters of this document.

Conceptual Design and Feasibility of Foil Bearings for Rotorcraft Engines: Hot Core Bearings

NASA Technical Reports Server (NTRS)

Howard, Samuel A.

2007-01-01

Recent developments in gas foil bearing technology have led to numerous advanced high-speed rotating system concepts, many of which have become either commercial products or experimental test articles. Examples include oil-free microturbines, motors, generators and turbochargers. The driving forces for integrating gas foil bearings into these high-speed systems are the benefits promised by removing the oil lubrication system. Elimination of the oil system leads to reduced emissions, increased reliability, and decreased maintenance costs. Another benefit is reduced power plant weight. For rotorcraft applications, this would be a major advantage, as every pound removed from the propulsion system results in a payload benefit.. Implementing foil gas bearings throughout a rotorcraft gas turbine engine is an important long-term goal that requires overcoming numerous technological hurdles. Adequate thrust bearing load capacity and potentially large gearbox applied radial loads are among them. However, by replacing the turbine end, or hot section, rolling element bearing with a gas foil bearing many of the above benefits can be realized. To this end, engine manufacturers are beginning to explore the possibilities of hot section gas foil bearings in propulsion engines. This overview presents a logical follow-on activity by analyzing a conceptual rotorcraft engine to determine the feasibility of a foil bearing supported core. Using a combination of rotordynamic analyses and a load capacity model, it is shown to be reasonable to consider a gas foil bearing core section. In addition, system level foil bearing testing capabilities at NASA Glenn Research Center are presented along with analysis work being conducted under NRA Cooperative Agreements.

The two-brain approach: how can mutually interacting brains teach us something about social interaction?

PubMed Central

Konvalinka, Ivana; Roepstorff, Andreas

2012-01-01

Measuring brain activity simultaneously from two people interacting is intuitively appealing if one is interested in putative neural markers of social interaction. However, given the complex nature of interactions, it has proven difficult to carry out two-person brain imaging experiments in a methodologically feasible and conceptually relevant way. Only a small number of recent studies have put this into practice, using fMRI, EEG, or NIRS. Here, we review two main two-brain methodological approaches, each with two conceptual strategies. The first group has employed two-brain fMRI recordings, studying (1) turn-based interactions on the order of seconds, or (2) pseudo-interactive scenarios, where only one person is scanned at a time, investigating the flow of information between brains. The second group of studies has recorded dual EEG/NIRS from two people interacting, in (1) face-to-face turn-based interactions, investigating functional connectivity between theory-of-mind regions of interacting partners, or in (2) continuous mutual interactions on millisecond timescales, to measure coupling between the activity in one person's brain and the activity in the other's brain. We discuss the questions these approaches have addressed, and consider scenarios when simultaneous two-brain recordings are needed. Furthermore, we suggest that (1) quantification of inter-personal neural effects via measures of emergence, and (2) multivariate decoding models that generalize source-specific features of interaction, may provide novel tools to study brains in interaction. This may allow for a better understanding of social cognition as both representation and participation. PMID:22837744

A single competency-based education and training and competency-based career framework for the Australian health workforce: discussing the potential value add

PubMed Central

Brownie, Sharon Mary; Thomas, Janelle

2014-01-01

This brief discusses the policy implications of a research study commissioned by Health Workforce Australia (HWA) within its health workforce innovation and reform work program. The project explored conceptually complex and operationally problematic concepts related to developing a whole-of-workforce competency-based education and training and competency-based career framework for the Australian health workforce and culminated with the production of three reports published by HWA. The project raised important queries as to whether such a concept is desirable, feasible or implementable – in short what is the potential value add and is it achievable? In setting the scene for discussion, the foundation of the project’s genesis and focus of the study are highlighted. A summary of key definitions related to competency-based education and training frameworks and competency-based career frameworks are provided to further readers’ commonality of understanding. The nature of the problem to be solved is explored and the potential value-add for the Australian health workforce and its key constituents proposed. The paper concludes by discussing relevance and feasibility issues within Australia’s current and changing healthcare context along with the essential steps and implementation realities that would need to be considered and actioned if whole-of-workforce frameworks were to be developed and implemented. PMID:25279384

The effect of conceptual metaphors through guided inquiry on student's conceptual change

NASA Astrophysics Data System (ADS)

Menia, Meli; Mudzakir, Ahmad; Rochintaniawati, Diana

2017-05-01

The purpose of this study was to identify student's conceptual change of global warming after integrated science learning based guided inquiry through conceptual metaphors. This study used a quasi-experimental with a nonequivalent control group design. The subject was students of two classes of one of MTsN Salido. Data was collected using conceptual change test (pretest and posttest), observation sheet to observe the learning processes, questionnaire sheet to identify students responses, and interview to identifyteacher'srespons of science learning with conceptual metaphors. The results showed that science learning based guided inquiry with conceptual metaphors is better than science learning without conceptual metaphors. The average of posttest experimental class was 79,40 and control class was 66,09. The student's conceptual change for two classes changed significantly byusing mann whitney U testwith P= 0,003(P less than sig. value, P< 0,05). This means that there was differenceson student's conceptual changebeetwen integrated science learning based guided inquiry with conceptual metaphors class and integrated science learning without conceptual metaphors class. The study also showed that teachers and studentsgive positive responsesto implementation of integrated science learning based guided inquiry with conceptual metaphors.

Utilizing Three-Dimensional Printing Technology to Assess the Feasibility of High-Fidelity Synthetic Ventricular Septal Defect Models for Simulation in Medical Education.

PubMed

Costello, John P; Olivieri, Laura J; Krieger, Axel; Thabit, Omar; Marshall, M Blair; Yoo, Shi-Joon; Kim, Peter C; Jonas, Richard A; Nath, Dilip S

2014-07-01

The current educational approach for teaching congenital heart disease (CHD) anatomy to students involves instructional tools and techniques that have significant limitations. This study sought to assess the feasibility of utilizing present-day three-dimensional (3D) printing technology to create high-fidelity synthetic heart models with ventricular septal defect (VSD) lesions and applying these models to a novel, simulation-based educational curriculum for premedical and medical students. Archived, de-identified magnetic resonance images of five common VSD subtypes were obtained. These cardiac images were then segmented and built into 3D computer-aided design models using Mimics Innovation Suite software. An Objet500 Connex 3D printer was subsequently utilized to print a high-fidelity heart model for each VSD subtype. Next, a simulation-based educational curriculum using these heart models was developed and implemented in the instruction of 29 premedical and medical students. Assessment of this curriculum was undertaken with Likert-type questionnaires. High-fidelity VSD models were successfully created utilizing magnetic resonance imaging data and 3D printing. Following instruction with these high-fidelity models, all students reported significant improvement in knowledge acquisition (P < .0001), knowledge reporting (P < .0001), and structural conceptualization (P < .0001) of VSDs. It is feasible to use present-day 3D printing technology to create high-fidelity heart models with complex intracardiac defects. Furthermore, this tool forms the foundation for an innovative, simulation-based educational approach to teach students about CHD and creates a novel opportunity to stimulate their interest in this field. © The Author(s) 2014.

Application of Deterministic and Probabilistic System Design Methods and Enhancements of Conceptual Design Tools for ERA Project

NASA Technical Reports Server (NTRS)

Mavris, Dimitri N.; Schutte, Jeff S.

2016-01-01

This report documents work done by the Aerospace Systems Design Lab (ASDL) at the Georgia Institute of Technology, Daniel Guggenheim School of Aerospace Engineering for the National Aeronautics and Space Administration, Aeronautics Research Mission Directorate, Integrated System Research Program, Environmentally Responsible Aviation (ERA) Project. This report was prepared under contract NNL12AA12C, "Application of Deterministic and Probabilistic System Design Methods and Enhancement of Conceptual Design Tools for ERA Project". The research within this report addressed the Environmentally Responsible Aviation (ERA) project goal stated in the NRA solicitation "to advance vehicle concepts and technologies that can simultaneously reduce fuel burn, noise, and emissions." To identify technology and vehicle solutions that simultaneously meet these three metrics requires the use of system-level analysis with the appropriate level of fidelity to quantify feasibility, benefits and degradations, and associated risk. In order to perform the system level analysis, the Environmental Design Space (EDS) [Kirby 2008, Schutte 2012a] environment developed by ASDL was used to model both conventional and unconventional configurations as well as to assess technologies from the ERA and N+2 timeframe portfolios. A well-established system design approach was used to perform aircraft conceptual design studies, including technology trade studies to identify technology portfolios capable of accomplishing the ERA project goal and to obtain accurate tradeoffs between performance, noise, and emissions. The ERA goal, shown in Figure 1, is to simultaneously achieve the N+2 benefits of a cumulative noise margin of 42 EPNdB relative to stage 4, a 75 percent reduction in LTO NOx emissions relative to CAEP 6 and a 50 percent reduction in fuel burn relative to the 2005 best in class aircraft. There were 5 research task associated with this research: 1) identify technology collectors, 2) model technology collectors in EDS, 3) model and assess ERA technologies, 4) LTO and cruise emission prediction, and 5) probabilistic analysis of technology collectors and portfolios.

Samoan Philosophy of Nursing: a basis for culturally proficient care and policy.

PubMed

Enoka, I S; Petrini, M A; Turale, S

2014-09-01

To explore nurses' perspectives about the Samoan Philosophy of Nursing, and determine its feasibility for nursing care of Samoans internationally. This philosophy is the conceptual cultural framework for nursing law, practice, education and research in Samoa, and was developed by Samoan nurses who recognized the need for guidance to deliver quality, culturally competent and proficient health care. A mixed method study, employing a questionnaire and ethnographic methods. The Samoan Philosophy of Nursing Questionnaire sought demographic data and aspects about the philosophy from 95 registered nurse clinicians, administrators and educators throughout Samoa during 2012. Descriptive statistics were used for data analysis. Additionally, 19 focus groups (5-6 participants each) and 19 in-depth interviews were held to further explore these aspects, as well as participant observations. Descriptive statistics were used to analyse quantitative data, and Spradley's ethnographic method was adopted for analysing the qualitative data. Of 95 questionnaires analysed, 70% of participants reported using the philosophy all the time, and 30% most of the time. They placed a high satisfaction rate, value and importance on this philosophy. From the ethnography, six major themes emerged: valuable framework of learning; conceptual framework for holistic assessment; benchmark for regulating and monitoring practice improving interaction and culturally proficient practice; potential use for Samoans overseas; and maintaining quality health and the dignity of people. This first-time study evaluated the Samoan Philosophy of Nursing and adds to nursing knowledge. Findings confirmed its usefulness as a culturally based conceptual framework to facilitate, regulate and monitor education, research and practice for sustainable health outcomes in Samoa, and for Samoans living abroad. It is important that Samoans living abroad receive culturally proficient care, but this requires the support of policymakers, nurse leaders and educators so that nurses internationally can access and competently utilize relevant aspects of this philosophy in practice. © 2014 International Council of Nurses.

Treatment Fidelity Among Family Health Promoters Delivering a Physical Activity and Nutrition Intervention to Immigrant and Refugee Families.

PubMed

Bronars, Carrie A; Hanza, Marcelo M; Meiers, Sonja J; Patten, Christi A; Clark, Matthew M; Nigon, Julie A; Weis, Jennifer A; Wieland, Mark L; Sia, Irene G

2017-04-01

Lack of treatment fidelity can be an important source of variation affecting the credibility and utility of outcomes from behavioral intervention research. Development and implementation of a well-designed treatment fidelity plan, especially with research involving underserved populations, requires careful conceptualization of study needs in conjunction with what is feasible in the population. The purpose of this article is to review a fidelity-monitoring plan consistent with the National Institutes of Health Behavior Change Consortium guidelines (e.g., design, training, delivery, receipt, and enactment) for an intervention trial designed to improve physical activity and nutrition among immigrant and refugee families. Description of the fidelity monitoring plan is provided and challenges related to monitoring treatment fidelity in a community-based participatory intervention for immigrant and refugee families are discussed.

The TMT instrumentation program

NASA Astrophysics Data System (ADS)

Simard, Luc; Crampton, David; Ellerbroek, Brent; Boyer, Corinne

2010-07-01

An overview of the current status of the Thirty Meter Telescope (TMT) instrumentation program is presented. Conceptual designs for the three first light instruments (IRIS, WFOS and IRMS) are in progress, as well as feasibility studies of MIRES. Considerable effort is underway to understand the end-to-end performance of the complete telescopeadaptive optics-instrument system under realistic conditions on Mauna Kea. Highly efficient operation is being designed into the TMT system, based on a detailed investigation of the observation workflow to ensure very fast target acquisition and set up of all subsystems. Future TMT instruments will almost certainly involve contributions from institutions in many different locations in North America and partner nations. Coordinating and optimizing the design and construction of the instruments to ensure delivery of the best possible scientific capabilities is an interesting challenge. TMT welcomes involvement from all interested instrument teams.

Standardization and economics of nuclear spacecraft: Executive summary

NASA Technical Reports Server (NTRS)

1973-01-01

Feasibility and cost benefits of nuclear-powered standardized spacecraft were investigated. The study indicates that two shuttle-launched nuclear-powered spacecraft should be able to serve the majority of unmanned NASA missions anticipated for the 1980's. The standard spacecraft include structure, thermal control, power, attitude control, some propulsion capability and tracking, telemetry, and command subsystems. One spacecraft design, powered by the radioisotope thermoelectric generator, can serve missions requiring up to 450 watts. The other spacecraft design, powered by similar nuclear heat sources in a Brayton-cycle generator, can serve missions requiring up to 2200 watts. Design concepts and trade-offs are discussed. The conceptual designs selected are presented and successfully tested against a variety of missions. The thermal design is such that both spacecraft are capable of operating in any earth orbit and any orientation without modification.

Hypersonic Research Vehicle (HRV) real-time flight test support feasibility and requirements study. Part 2: Remote computation support for flight systems functions

NASA Technical Reports Server (NTRS)

Rediess, Herman A.; Hewett, M. D.

1991-01-01

The requirements are assessed for the use of remote computation to support HRV flight testing. First, remote computational requirements were developed to support functions that will eventually be performed onboard operational vehicles of this type. These functions which either cannot be performed onboard in the time frame of initial HRV flight test programs because the technology of airborne computers will not be sufficiently advanced to support the computational loads required, or it is not desirable to perform the functions onboard in the flight test program for other reasons. Second, remote computational support either required or highly desirable to conduct flight testing itself was addressed. The use is proposed of an Automated Flight Management System which is described in conceptual detail. Third, autonomous operations is discussed and finally, unmanned operations.

Expert AIV: Study and Prototyping of an Expert System, To Support the Conceptual AIV Phases Of Space Programs

NASA Astrophysics Data System (ADS)

Andrina, G.; Basso, V.; Saitta, L.

2004-08-01

The effort in optimising the AIV process has been mainly focused in the recent years on the standardisation of approaches and on the application of new methodologies. But the earlier the intervention, the greater the benefits in terms of cost and schedule. Early phases of AIV process relied up to now on standards that need to be tailored through company and personal expertise. A study has then been conducted in order to exploit the possibility to develop an expert system helping in making choices in the early, conceptual phase of Assembly, Integration and Verification, namely the Model Philosophy and the test definition. The work focused on a hybrid approach, allowing interaction between historical data and human expertise. The expert system that has been prototyped exploits both information elicited from domain experts and results of a Data Mining activity on the existent data bases of completed projects verification data. The Data Mining algorithms allow the extraction of past experience resident on ESA/ MATD data base, which contains information in the form of statistical summaries, costs, frequencies of on-ground and in flight failures. Finding non-trivial associations could then be utilised by the experts to manage new decisions in a controlled way (Standards driven) at the beginning or during the AIV Process Moreover, the Expert AIV could allow compilation of a set of feasible AIV schedules to support further programmatic-driven choices.

Results of a feasibility study: barriers and facilitators in implementing the Sherbrooke model in France.

PubMed

Fassier, Jean-Baptiste; Durand, Marie-José; Caillard, Jean-François; Roquelaure, Yves; Loisel, Patrick

2015-05-01

Return-to-work interventions associated with the workplace environment are often more effective than conventional care. The Sherbrooke model is an integrated intervention that has proved successful in preventing work disability due to low-back pain. Implementation, however, runs up against many obstacles, and failure has been reported in many countries. The present study sought to identify barriers to and facilitators of the implementation of the Sherbrooke model within the French health system. A multiple case study with nested levels of analysis was performed in two regions of France. A conceptual framework was designed and refined to identify barriers and facilitators at the individual, organizational and contextual levels. Qualitative data were collected via semi-structured interview (N=22), focus groups (N=7), and observation and from the gray literature. Participants (N=61) belonged to three fields: healthcare, social insurance, and the workplace. Numerous barriers and facilitators were identified in each field and at each level, some specific and others common to workers in all fields. Individual and organizational barriers comprised lack of time and resources, discordant professional values, and perceived risk. Legal barriers comprised medical confidentiality, legal complexity, and priority given to primary prevention. Individual-level facilitators comprised needs and perceived benefits. Some organizations had concordant values and practices. Legal facilitators comprised possibilities of collaboration and gradual return to work. The present feasibility analysis of implementing the Sherbrooke model revealed numerous barriers and facilitators suggesting a new implementation strategy be drawn up if failure is to be avoided.

A Yoga Stress Reduction Intervention for University Faculty, Staff, and Graduate Students.

PubMed

Brems, Christiane

2015-01-01

Yoga can be an effective intervention for physical and psychological symptoms and decreased ability to cope with physical, emotional, vocational, or academic stress. One group of individuals challenged regarding adequate self-care in the face of stress are personnel in university training programs for helping professions (e.g., psychology, nursing, nutrition). This feasibility study explored engagement in and effectiveness of a systematic 10-week yoga program aimed at university faculty, staff, and students. The intervention consisted of 10 weekly 90-minute sessions that were structured to include conceptual grounding, breathing, postures, and meditation. Weekly class outlines were made available to students for home practice. Participants signed informed consents, liability waivers, and health screenings. Self-reports of home practice, barriers to practice, perceived stress, and stress symptoms were used to evaluate whether the intervention was successful in engaging participants and reducing stress-related symptoms. Engagement was demonstrated by study adherence in the first 10-week series (88%; 44 of 50 enrolled), as well as re-enrollment for at least one additional 10-week series (64%; 28 of 44). Intervention success was demonstrated through repeated measure s ANOVAs of 44 participants' data, which showed significant improvement after a single 10-week series in perceived stress, as well as self-reported psychological, behavioral, and physical symptoms of stress. The study demonstrates feasibility of a yoga intervention in an academic setting and provides preliminary evidence for efficacy in stress reduction. It also supplies 10 detailed session protocols for intervention replication.

Converting a C-130 Hercules into a Compound Helicopter: A Conceptual Design Study

NASA Technical Reports Server (NTRS)

Kottapalli, Anjaney P.; Harris, Franklin D.

2012-01-01

Currently, the US Military and NASA are investigating the feasibility of a Vertical/Short Take Off and Landing (VSTOL) aircraft that can provide invaluable aid in the combat theater and significantly improve the civil transportation system. The nominal military mission requirement calls for a 28-ton payload heavy lift capability while the civilian requirements calls for a 90-passenger, 1000-nm range, airliner, as noted in Reference 1. To aid in these aircraft requirements, the present study examined the conversion of a Lockheed Martin C-130 Hercules into a compound aircraft, which would demonstrate the technology required by a much larger version. The present study examined various configurations and rotor blade designs in order to fulfill the nominal mission described previously. It was shown that the initial design of a 180 ft diameter rotor to lift 155,000 lb was not feasible due to material constraints. A revised design, in which the rotor radius was reduced to 55 ft, met the given constraints but required too much power. The decision was made to move to a twin rotor compound to take advantage of the increased disc area and drop the need for anti torque devices. Following this design shift, a new design point was found where all five constraints were met and the power requirements were deemed reasonable. This twin-rotor design was used in NDARC to provide a complete sizing analysis of the chosen design point.

Expérience de fréquentation des lieux publics par des personnes âgées ayant subi un TCC en présence d'un accompagnateur-citoyen: projet pilote.

PubMed

Levert, Marie-Josée; Lefebvre, Hélène; Gélinas, Isabelle; McKerall, Michelle; Roy, Odette; Proulx, Michelle

2016-06-01

This pilot project aims to test and see the relevance of the direct observation method to collect data on the barriers and facilitators to attending public places by seniors with TBI. The study is based on the conceptual framework VADA WHO which focuses on the development of friendly built and technological environments for seniors. Three elderly people participated in the study, recruited from an ongoing project, The Citizen Intervention in Community Living (APIC), in the presence of their personalized attendant. The study shows the feasibility of the method in terms of its acceptability and resources mobilized. It shows its relevance to access additional data that would have been difficult to obtain using others methods (e.g., semi-structured interview), such as the identification of the strategies used by the participants to address the obstacles encountered (avoidance, travel planning, use of physical and preventative support of the personalized attendant).

Advanced sensible heat solar receiver for space power

NASA Technical Reports Server (NTRS)

Bennett, Timothy J.; Lacy, Dovie E.

1988-01-01

NASA Lewis, through in-house efforts, has begun a study to generate a conceptual design of a sensible heat solar receiver and to determine the feasibility of such a system for space power applications. The sensible heat solar receiver generated in this study uses pure lithium as the thermal storage medium and was designed for a 7 kWe Brayton (PCS) operating at 1100 K. The receiver consists of two stages interconnected via temperature sensing variable conductance sodium heat pipes. The lithium is contained within a niobium vessel and the outer shell of the receiver is constructed of third generation rigid, fibrous ceramic insulation material. Reradiation losses are controlled with niobium and aluminum shields. By nature of design, the sensible heat receiver generated in this study is comparable in both size and mass to a latent heat system of similar thermal capacitance. The heat receiver design and thermal analysis was conducted through the combined use of PATRAN, SINDA, TRASYS, and NASTRAN software packages.

Advanced sensible heat solar receiver for space power

NASA Technical Reports Server (NTRS)

Bennett, Timothy J.; Lacy, Dovie E.

1988-01-01

NASA Lewis, through in-house efforts, has begun a study to generate a conceptual design of a sensible heat solar receiver and to determine the feasibility of such a system for space power applications. The sensible heat solar receiver generated in this study uses pure lithium as the thermal storage medium and was designed for a 7 kWe Brayton (PCS) operating at 1100 K. The receiver consists of two stages interconnected via temperature sensing variable conductance sodium heat pipes. The lithium is contained within a niobium vessel and the outer shell of the receiver is constructed of third generation rigid, fibrous ceramic insulation material. Reradiation losses are controlled with niobium and aluminum shields. By nature of design, the sensible heat receiver generated in this study is comparable in both size and mass to a latent heat system of similar thermal capacitance. The heat receiver design and thermal analysis were conducted through the combined use of PATRAN, SINDA, TRASYS, and NASTRAN software packages.

Assessing the impact of modeling limits on intelligent systems

NASA Technical Reports Server (NTRS)

Rouse, William B.; Hammer, John M.

1990-01-01

The knowledge bases underlying intelligent systems are validated. A general conceptual framework is provided for considering the roles in intelligent systems of models of physical, behavioral, and operational phenomena. A methodology is described for identifying limits in particular intelligent systems, and the use of the methodology is illustrated via an experimental evaluation of the pilot-vehicle interface within the Pilot's Associate. The requirements and functionality are outlined for a computer based knowledge engineering environment which would embody the approach advocated and illustrated in earlier discussions. Issues considered include the specific benefits of this functionality, the potential breadth of applicability, and technical feasibility.

Conceptual Design, Feasibility and Payoff Analysis of a Third Stage for EELV (Briefing Charts)

DTIC Science & Technology

2014-07-30

performance capability – Hydrazine, N2O4/MMH, LOX/RP, H2O2/RP, LOX/CH4, LOX/ LH2 (MR of 6), and LOX/ LH2 (MR of 10) • Propulsion system split into multiple...area ratio attainable within length envelope – Use of four chambers allows area ratios >150 – LOX/ LH2 (MR=6) is highest performing propellant...combination •Due to LOX/ LH2 (MR=6) low bulk density it is not possible to store as much propellant within stage – Resulting in the lowest total

A Foundational Approach to Designing Geoscience Ontologies

NASA Astrophysics Data System (ADS)

Brodaric, B.

2009-05-01

E-science systems are increasingly deploying ontologies to aid online geoscience research. Geoscience ontologies are typically constructed independently by isolated individuals or groups who tend to follow few design principles. This limits the usability of the ontologies due to conceptualizations that are vague, conflicting, or narrow. Advances in foundational ontologies and formal engineering approaches offer promising solutions, but these advanced techniques have had limited application in the geosciences. This paper develops a design approach for geoscience ontologies by extending aspects of the DOLCE foundational ontology and the OntoClean method. Geoscience examples will be presented to demonstrate the feasibility of the approach.

A Jupiter Orbiter mother/daughter spacecraft concept

NASA Technical Reports Server (NTRS)

Duxbury, J. H.

1975-01-01

The feasibility of a tandem launch of a mother/daughter spacecraft pair with a single launch vehicle for a 1981 Mariner Jupiter Orbiter mission is described. The mother is a close derivative of the three-axis stabilized Mariner Jupiter Saturn 1977 spacecraft with the addition of a Viking-type propulsion module for orbit capture; it concentrates on the planetology and satellite science objectives. The daughter is a small, simple spin-stabilized spacecraft taking advantage of the mother's transit and delivery capabilities; it obtains in-situ measurements of the surrounding planetary environment. A conceptual design of the daughter spacecraft is presented.

EOS production on the Space Station. [Electrophoresis Operations/Space

NASA Technical Reports Server (NTRS)

Runge, F. C.; Gleason, M.

1986-01-01

The paper discusses a conceptual integration of the equipment for EOS (Electrophoresis Operations/Space) on the Space Station in the early 1990s. Electrophoresis is a fluid-constituent separation technique which uses forces created by an electrical field. Aspects covered include EOS equipment and operations, and Space Station installations involving a pressurized module, a resupply module, utility provisions and umbilicals and crew involvement. Accommodation feasibility is generally established, and interfaces are defined. Space Station production of EOS-derived pharmaceuticals will constitute a significant increase in capability compared to precursor flights on the Shuttle in the 1980s.

Development and testing of a fast conceptual river water quality model.

PubMed

Keupers, Ingrid; Willems, Patrick

2017-04-15

Modern, model based river quality management strongly relies on river water quality models to simulate the temporal and spatial evolution of pollutant concentrations in the water body. Such models are typically constructed by extending detailed hydrodynamic models with a component describing the advection-diffusion and water quality transformation processes in a detailed, physically based way. This approach is too computational time demanding, especially when simulating long time periods that are needed for statistical analysis of the results or when model sensitivity analysis, calibration and validation require a large number of model runs. To overcome this problem, a structure identification method to set up a conceptual river water quality model has been developed. Instead of calculating the water quality concentrations at each water level and discharge node, the river branch is divided into conceptual reservoirs based on user information such as location of interest and boundary inputs. These reservoirs are modelled as Plug Flow Reactor (PFR) and Continuously Stirred Tank Reactor (CSTR) to describe advection and diffusion processes. The same water quality transformation processes as in the detailed models are considered but with adjusted residence times based on the hydrodynamic simulation results and calibrated to the detailed water quality simulation results. The developed approach allows for a much faster calculation time (factor 10 5 ) without significant loss of accuracy, making it feasible to perform time demanding scenario runs. Copyright © 2017 Elsevier Ltd. All rights reserved.

‘Croque&bouge’: A feasible and acceptable programme for obesity prevention in preschoolers at risk and their parents

PubMed Central

Dudley-Martin, Fiona; Kruseman, Maaike

2015-01-01

Objectives: To conceptualize and pilot test a programme of three workshops aiming to prevent the development of overweight in susceptible preschool children. Methods: Three workshops were conducted, targeting both parents and children. The curriculum for parents included discussions on feeding responsibilities, healthy eating, taste development, neophobia and physical activity recommendations. Children participated in various play activities with fruits and vegetables and read stories about hunger and satiety feelings. Recruitment was organized through paediatricians and child-care centres. Evaluation of the programme focused on feasibility, adequacy for children’s age, parents’ perception of impact and, for children, change of the ability to recognize and willingness to taste fruits and vegetables. Results: A total of 21 children and one of their parents participated in the programme. The programme was found to be feasible and adequate for the targeted community. Parents reported perceiving a positive impact of the intervention; however, this finding was not statistically significant. The major difficulty was identifying and recruiting families and engaging the parents in a discussion about weight. Conclusions: This short programme aiming to improve parents’ ability to offer healthy environment and promote healthy eating behaviour was feasible and acceptable for families with young children. When developing and implementing such programmes, close collaboration with paediatricians and other health providers should be sought in order to identify and reach children at risk of obesity and their family. PMID:26770769

Using Normalization Process Theory in feasibility studies and process evaluations of complex healthcare interventions: a systematic review.

PubMed

May, Carl R; Cummings, Amanda; Girling, Melissa; Bracher, Mike; Mair, Frances S; May, Christine M; Murray, Elizabeth; Myall, Michelle; Rapley, Tim; Finch, Tracy

2018-06-07

Normalization Process Theory (NPT) identifies, characterises and explains key mechanisms that promote and inhibit the implementation, embedding and integration of new health techniques, technologies and other complex interventions. A large body of literature that employs NPT to inform feasibility studies and process evaluations of complex healthcare interventions has now emerged. The aims of this review were to review this literature; to identify and characterise the uses and limits of NPT in research on the implementation and integration of healthcare interventions; and to explore NPT's contribution to understanding the dynamics of these processes. A qualitative systematic review was conducted. We searched Web of Science, Scopus and Google Scholar for articles with empirical data in peer-reviewed journals that cited either key papers presenting and developing NPT, or the NPT Online Toolkit ( www.normalizationprocess.org ). We included in the review only articles that used NPT as the primary approach to collection, analysis or reporting of data in studies of the implementation of healthcare techniques, technologies or other interventions. A structured data extraction instrument was used, and data were analysed qualitatively. Searches revealed 3322 citations. We show that after eliminating 2337 duplicates and broken or junk URLs, 985 were screened as titles and abstracts. Of these, 101 were excluded because they did not fit the inclusion criteria for the review. This left 884 articles for full-text screening. Of these, 754 did not fit the inclusion criteria for the review. This left 130 papers presenting results from 108 identifiable studies to be included in the review. NPT appears to provide researchers and practitioners with a conceptual vocabulary for rigorous studies of implementation processes. It identifies, characterises and explains empirically identifiable mechanisms that motivate and shape implementation processes. Taken together, these mean that analyses using NPT can effectively assist in the explanation of the success or failure of specific implementation projects. Ten percent of papers included critiques of some aspect of NPT, with those that did mainly focusing on its terminology. However, two studies critiqued NPT emphasis on agency, and one study critiqued NPT for its normative focus. This review demonstrates that researchers found NPT useful and applied it across a wide range of interventions. It has been effectively used to aid intervention development and implementation planning as well as evaluating and understanding implementation processes themselves. In particular, NPT appears to have offered a valuable set of conceptual tools to aid understanding of implementation as a dynamic process.

Using concept mapping to mobilize a Black faith community to address HIV

PubMed Central

Szaflarski, Magdalena; Vaughn, Lisa M; McLinden, Daniel; Wess, Yolanda; Ruffner, Andrew

2017-01-01

Research that partners with community stakeholders increases contextual relevance and community buy-in and maximizes the chance for intervention success. Within a framework of an academic-community partnership, this project assessed a Black faith-community’s needs and opportunities to address HIV. We used concept mapping to identify/prioritize specific HIV-related strategies that would be acceptable to congregations. Ninety stakeholders brainstormed strategies to address HIV; 21 sorted strategies into groups and rated their importance and feasibility. Multidimensional scaling and cluster analysis were applied to the sorting to produce maps that illustrated the stakeholders’ conceptual thinking about HIV interventions. Of 278 responses, 93 were used in the sorting task. The visual maps represented eight clusters: church acceptance of people living with HIV; education (most feasible); mobilization and communication; church/leaders’ empowerment; church involvement/collaboration; safety/HIV prevention; media outreach; and, stigma (most important). Concept mapping clarified multifaceted issues of HIV in the Black faith community. The results will guide HIV programming in congregations. PMID:28239439

Feasibility of Estimating Relative Nutrient Contributions of Agriculture and Forests Using MODIS Time Series

NASA Technical Reports Server (NTRS)

Ross, Kenton W.; Gasser, Gerald; Spiering, Bruce

2010-01-01

Around the Gulf of Mexico, high-input crops in several regions make a significant contribution to nutrient loading of small to medium estuaries and to the near-shore Gulf. Some crops cultivated near the coast include sorghum in Texas, rice in Texas and Louisiana, sugarcane in Florida and Louisiana, citrus orchards in Florida, pecan orchards in Mississippi and Alabama, and heavy sod and ornamental production around Mobile and Tampa Bay. In addition to crops, management of timberlands in proximity to the coasts also plays a role in nutrient loading. In the summer of 2008, a feasibility project is planned to explore the use of NASA data to enhance the spatial and temporal resolution of near-coast nutrient source information available to the coastal community. The purpose of this project is to demonstrate the viability of nutrient source information products applicable to small to medium watersheds surrounding the Gulf of Mexico. Conceptually, these products are intended to complement estuarine nutrient monitoring.

Feasibility of Estimating Relative Nutrient Contributions of Agriculture using MODIS Time Series

NASA Technical Reports Server (NTRS)

Ross, Kenton W.; Gasser, Gerald; Spiering, Bruce

2008-01-01

Around the Gulf of Mexico, high-input crops in several regions make a significant contribution to nutrient loading of small to medium estuaries and to the near-shore Gulf. Some crops cultivated near the coast include sorghum in Texas, rice in Texas and Louisiana, sugarcane in Florida and Louisiana, citrus orchards in Florida, pecan orchards in Mississippi and Alabama, and heavy sod and ornamental production around Mobile and Tampa Bay. In addition to crops, management of timberlands in proximity to the coasts also plays a role in nutrient loading. In the summer of 2008, a feasibility project is planned to explore the use of NASA data to enhance the spatial and temporal resolution of near-coast nutrient source information available to the coastal community. The purpose of this project is to demonstrate the viability of nutrient source information products applicable to small to medium watersheds surrounding the Gulf of Mexico. Conceptually, these products are intended to complement estuarine nutrient monitoring.

Mechanical conceptual design of 6.5 meter telescope: Telescopio San Pedro Mártir (TSPM)

NASA Astrophysics Data System (ADS)

Uribe, Jorge; Bringas, Vicente; Reyes, Noe; Tovar, Carlos; López, Aldo; Caballero, Xóchitl; Martínez, César; Toledo, Gengis; Lee, William; Carramiñana, Alberto; González, Jesús; Richer, Michael; Sánchez, Beatriz; Lucero, Diana; Manuel, Rogelio; Rubio, Saúl; González, Germán.; Hernández, Obed; Segura, José; Macias, Eduardo; García, Mary; Lazaro, José; Rosales, Fabián.; del Llano, Luis

2016-07-01

Telescopio San Pedro Mártir (TSPM) project intends to build a 6.5 meters telescope with alt-azimuth design, currently at the conceptual design. The project is an association between Instituto de Astronomía de la Universidad Nacional Autónoma de México (IA-UNAM) and the Instituto Nacional de Astrofísica, Óptica Electrónica (INAOE) in partnership with department of Astronomy and Steward Observatory of University of Arizona and Smithsonian Astrophysical Observatory of Harvard University. Conceptual design of the telescope is lead and developed by the Centro de Ingeniería y Desarrollo Industrial (CIDESI). An overview of the feasibility study and the structural conceptual design are summarized in this paper. The telescope concept is based on telescopes already commissioned such as MMT and the Baade and Clay Magellan telescopes, building up on these proven concepts. The main differences relative to the Magellan pair are; the elevation axis is located 1 meter above the primary mirror vertex, allowing for a similar field of view at the Cassegrain and both Nasmyth focal stations; instead of using a vane ends to position the secondary mirror TSPM considers an Steward platform like MMT; finally TSPM has a larger floor distance to m1 cell than Magellans and MMT. Initially TSPM will operate with an f/5 Cassegrain station, but the design considers further Nasmyth configurations from a Cassegrain f/5 up to a Gregorian f/11. The telescope design includes 7 focal stations: 1 Cassegrain; 2 Nasmyth; and 4 folded-Cassegrain. The telescope will be designed and manufactured in Mexico, will be design in Queretaro by CIDESI and built between Queretaro and Michoacán manufacturing facilities; it will be preassembled in these facilities and disassembled to send it to the San Pedro Mártir Observatory for final integration. The azimuth and altitude structure is planned to be constructed in modules and transported by truck and shipped to Ensenada and finally to the OAN where is going to be finally assembled, verified and tested.

Conceptual design for a laminar-flying-wing aircraft

NASA Astrophysics Data System (ADS)

Saeed, T. I.

The laminar-flying-wing aircraft appears to be an attractive long-term prospect for reducing the environmental impact of commercial aviation. In assessing its potential, a relatively straightforward initial step is the conceptual design of a version with restricted sweep angle. Such a design is the topic of this thesis. Subject to constraints, this research aims to; provide insight into the parameters affecting practical laminar-flow-control suction power requirements; identify a viable basic design specification; and, on the basis of this, an assessment of the fuel efficiency through a detailed conceptual design study. It is shown that there is a minimum power requirement independent of the suction system design, associated with the stagnation pressure loss in the boundary layer. This requirement increases with aerofoil section thickness, but depends only weakly on Mach number and (for a thick, lightly-loaded laminar flying wing) lift coefficient. Deviation from the optimal suction distribution, due to a practical chamber-based architecture, is found to have very little effect on the overall suction coefficient. In the spanwise direction, through suitable choice of chamber depth, the pressure drop due to frictional and inertial effects may be rendered negligible. Finally, it is found that the pressure drop from the aerofoil surface to the pump collector ducts determines the power penalty. To identify the viable basic design specification, a high-level exploration of the laminar flying wing design space is performed. The characteristics of the design are assessed as a function of three parameters: thickness-to-chord ratio, wingspan, and unit Reynolds number. A feasible specification, with 20% thickness-to-chord, 80 m span and a unit Reynolds number of 8 x 106 m-1, is identified; it corresponds to a 187 tonne aircraft which cruises at Mach 0.67 and altitude 22,500 ft, with lift coefficient 0.14. On the basis of this specification, a detailed conceptual design is undertaken. A 220-passenger laminar-flying-wing concept, propelled by three turboprop engines, with a cruise range of 9000 km is developed. The laminar flying wing proposed in this thesis falls short of the performance improvements expected of the concept, and is not worth the development effort.

Sequence modelling and an extensible data model for genomic database

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li, Peter Wei-Der

1992-01-01

The Human Genome Project (HGP) plans to sequence the human genome by the beginning of the next century. It will generate DNA sequences of more than 10 billion bases and complex marker sequences (maps) of more than 100 million markers. All of these information will be stored in database management systems (DBMSs). However, existing data models do not have the abstraction mechanism for modelling sequences and existing DBMS's do not have operations for complex sequences. This work addresses the problem of sequence modelling in the context of the HGP and the more general problem of an extensible object data modelmore » that can incorporate the sequence model as well as existing and future data constructs and operators. First, we proposed a general sequence model that is application and implementation independent. This model is used to capture the sequence information found in the HGP at the conceptual level. In addition, abstract and biological sequence operators are defined for manipulating the modelled sequences. Second, we combined many features of semantic and object oriented data models into an extensible framework, which we called the Extensible Object Model'', to address the need of a modelling framework for incorporating the sequence data model with other types of data constructs and operators. This framework is based on the conceptual separation between constructors and constraints. We then used this modelling framework to integrate the constructs for the conceptual sequence model. The Extensible Object Model is also defined with a graphical representation, which is useful as a tool for database designers. Finally, we defined a query language to support this model and implement the query processor to demonstrate the feasibility of the extensible framework and the usefulness of the conceptual sequence model.« less

Sequence modelling and an extensible data model for genomic database

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li, Peter Wei-Der

1992-01-01

The Human Genome Project (HGP) plans to sequence the human genome by the beginning of the next century. It will generate DNA sequences of more than 10 billion bases and complex marker sequences (maps) of more than 100 million markers. All of these information will be stored in database management systems (DBMSs). However, existing data models do not have the abstraction mechanism for modelling sequences and existing DBMS`s do not have operations for complex sequences. This work addresses the problem of sequence modelling in the context of the HGP and the more general problem of an extensible object data modelmore » that can incorporate the sequence model as well as existing and future data constructs and operators. First, we proposed a general sequence model that is application and implementation independent. This model is used to capture the sequence information found in the HGP at the conceptual level. In addition, abstract and biological sequence operators are defined for manipulating the modelled sequences. Second, we combined many features of semantic and object oriented data models into an extensible framework, which we called the ``Extensible Object Model``, to address the need of a modelling framework for incorporating the sequence data model with other types of data constructs and operators. This framework is based on the conceptual separation between constructors and constraints. We then used this modelling framework to integrate the constructs for the conceptual sequence model. The Extensible Object Model is also defined with a graphical representation, which is useful as a tool for database designers. Finally, we defined a query language to support this model and implement the query processor to demonstrate the feasibility of the extensible framework and the usefulness of the conceptual sequence model.« less

A “Fork-to-Farm” Multi-Scale Approach to Promote Sustainable Food Systems for Nutrition and Health: A Perspective for the Mediterranean Region

PubMed Central

Verger, Eric O.; Perignon, Marlene; El Ati, Jalila; Darmon, Nicole; Dop, Marie-Claude; Drogué, Sophie; Dury, Sandrine; Gaillard, Cédric; Sinfort, Carole; Amiot, Marie-Josèphe; Amiot, Marie-Josèphe

2018-01-01

Mediterranean countries are undergoing dietary and nutritional changes that affect their inhabitants' health, while facing massive environmental challenges. The increasing demand of water in agriculture, the capacity to maintain local food production, and the growing dependence on food imports are interconnected issues that must be addressed to ensure food security and nutrition in the Mediterranean region. Here, we present the conceptual framework and methodologies developed by the MEDINA-Study Group for rethinking food systems toward sustainable consumption and production modes. Based on its multidisciplinary expertise, the MEDINA-Study Group designed a “fork-to-farm” multi-scale approach, stemming from current dietary habits and examining how some options to nutritionally improve these habits might affect the food systems. This approach was developed for research activities in the South of France and Tunisia, two areas with very different diet-agriculture-environment nexus. The conceptual framework is based on the analysis of elements of the food systems (from consumption to production) at different levels (individual, household, regional and national levels). The methods include: (i) modeling options of dietary changes at different scales, in order to nutritionally optimize food consumption-production without increasing the environmental impact, (ii) translating the best-choice changes into possible policy actions, (iii) testing the acceptability and feasibility of these actions with several stakeholders, and (iv) producing guidelines for sustainable food choices and production. The MEDINA-Study Group identified additional issues that could be included in a future framework to help designing ambitious agricultural, food and health policies in the Mediterranean region. PMID:29872660

Development of a prototype clinical decision support tool for osteoporosis disease management: a qualitative study of focus groups.

PubMed

Kastner, Monika; Li, Jamy; Lottridge, Danielle; Marquez, Christine; Newton, David; Straus, Sharon E

2010-07-22

Osteoporosis affects over 200 million people worldwide, and represents a significant cost burden. Although guidelines are available for best practice in osteoporosis, evidence indicates that patients are not receiving appropriate diagnostic testing or treatment according to guidelines. The use of clinical decision support systems (CDSSs) may be one solution because they can facilitate knowledge translation by providing high-quality evidence at the point of care. Findings from a systematic review of osteoporosis interventions and consultation with clinical and human factors engineering experts were used to develop a conceptual model of an osteoporosis tool. We conducted a qualitative study of focus groups to better understand physicians' perceptions of CDSSs and to transform the conceptual osteoporosis tool into a functional prototype that can support clinical decision making in osteoporosis disease management at the point of care. The conceptual design of the osteoporosis tool was tested in 4 progressive focus groups with family physicians and general internists. An iterative strategy was used to qualitatively explore the experiences of physicians with CDSSs; and to find out what features, functions, and evidence should be included in a working prototype. Focus groups were conducted using a semi-structured interview guide using an iterative process where results of the first focus group informed changes to the questions for subsequent focus groups and to the conceptual tool design. Transcripts were transcribed verbatim and analyzed using grounded theory methodology. Of the 3 broad categories of themes that were identified, major barriers related to the accuracy and feasibility of extracting bone mineral density test results and medications from the risk assessment questionnaire; using an electronic input device such as a Tablet PC in the waiting room; and the importance of including well-balanced information in the patient education component of the osteoporosis tool. Suggestions for modifying the tool included the addition of a percentile graph showing patients' 10-year risk for osteoporosis or fractures, and ensuring that the tool takes no more than 5 minutes to complete. Focus group data revealed the facilitators and barriers to using the osteoporosis tool at the point of care so that it can be optimized to aid physicians in their clinical decision making.

Development of a prototype clinical decision support tool for osteoporosis disease management: a qualitative study of focus groups

PubMed Central

2010-01-01

Background Osteoporosis affects over 200 million people worldwide, and represents a significant cost burden. Although guidelines are available for best practice in osteoporosis, evidence indicates that patients are not receiving appropriate diagnostic testing or treatment according to guidelines. The use of clinical decision support systems (CDSSs) may be one solution because they can facilitate knowledge translation by providing high-quality evidence at the point of care. Findings from a systematic review of osteoporosis interventions and consultation with clinical and human factors engineering experts were used to develop a conceptual model of an osteoporosis tool. We conducted a qualitative study of focus groups to better understand physicians' perceptions of CDSSs and to transform the conceptual osteoporosis tool into a functional prototype that can support clinical decision making in osteoporosis disease management at the point of care. Methods The conceptual design of the osteoporosis tool was tested in 4 progressive focus groups with family physicians and general internists. An iterative strategy was used to qualitatively explore the experiences of physicians with CDSSs; and to find out what features, functions, and evidence should be included in a working prototype. Focus groups were conducted using a semi-structured interview guide using an iterative process where results of the first focus group informed changes to the questions for subsequent focus groups and to the conceptual tool design. Transcripts were transcribed verbatim and analyzed using grounded theory methodology. Results Of the 3 broad categories of themes that were identified, major barriers related to the accuracy and feasibility of extracting bone mineral density test results and medications from the risk assessment questionnaire; using an electronic input device such as a Tablet PC in the waiting room; and the importance of including well-balanced information in the patient education component of the osteoporosis tool. Suggestions for modifying the tool included the addition of a percentile graph showing patients' 10-year risk for osteoporosis or fractures, and ensuring that the tool takes no more than 5 minutes to complete. Conclusions Focus group data revealed the facilitators and barriers to using the osteoporosis tool at the point of care so that it can be optimized to aid physicians in their clinical decision making. PMID:20650007

Augmenting Parametric Optimal Ascent Trajectory Modeling with Graph Theory

NASA Technical Reports Server (NTRS)

Dees, Patrick D.; Zwack, Matthew R.; Edwards, Stephen; Steffens, Michael

2016-01-01

It has been well documented that decisions made in the early stages of Conceptual and Pre-Conceptual design commit up to 80% of total Life-Cycle Cost (LCC) while engineers know the least about the product they are designing [1]. Once within Preliminary and Detailed design however, making changes to the design becomes far more difficult to enact in both cost and schedule. Primarily this has been due to a lack of detailed data usually uncovered later during the Preliminary and Detailed design phases. In our current budget-constrained environment, making decisions within Conceptual and Pre-Conceptual design which minimize LCC while meeting requirements is paramount to a program's success. Within the arena of launch vehicle design, optimizing the ascent trajectory is critical for minimizing the costs present within such concerns as propellant, aerodynamic, aeroheating, and acceleration loads while meeting requirements such as payload delivered to a desired orbit. In order to optimize the vehicle design its constraints and requirements must be known, however as the design cycle proceeds it is all but inevitable that the conditions will change. Upon that change, the previously optimized trajectory may no longer be optimal, or meet design requirements. The current paradigm for adjusting to these updates is generating point solutions for every change in the design's requirements [2]. This can be a tedious, time-consuming task as changes in virtually any piece of a launch vehicle's design can have a disproportionately large effect on the ascent trajectory, as the solution space of the trajectory optimization problem is both non-linear and multimodal [3]. In addition, an industry standard tool, Program to Optimize Simulated Trajectories (POST), requires an expert analyst to produce simulated trajectories that are feasible and optimal [4]. In a previous publication the authors presented a method for combatting these challenges [5]. In order to bring more detailed information into Conceptual and Pre-Conceptual design, knowledge of the effects originating from changes to the vehicle must be calculated. In order to do this, a model capable of quantitatively describing any vehicle within the entire design space under consideration must be constructed. This model must be based upon analysis of acceptable fidelity, which in this work comes from POST. Design space interrogation can be achieved with surrogate modeling, a parametric, polynomial equation representing a tool. A surrogate model must be informed by data from the tool with enough points to represent the solution space for the chosen number of variables with an acceptable level of error. Therefore, Design Of Experiments (DOE) is used to select points within the design space to maximize information gained on the design space while minimizing number of data points required. To represent a design space with a non-trivial number of variable parameters the number of points required still represent an amount of work which would take an inordinate amount of time via the current paradigm of manual analysis, and so an automated method was developed. The best practices of expert trajectory analysts working within NASA Marshall's Advanced Concepts Office (ACO) were implemented within a tool called multiPOST. These practices include how to use the output data from a previous run of POST to inform the next, determining whether a trajectory solution is feasible from a real-world perspective, and how to handle program execution errors. The tool was then augmented with multiprocessing capability to enable analysis on multiple trajectories simultaneously, allowing throughput to scale with available computational resources. In this update to the previous work the authors discuss issues with the method and solutions.

Conceptual Design for a Dual-Bell Rocket Nozzle System Using a NASA F-15 Airplane as the Flight Testbed

NASA Technical Reports Server (NTRS)

Jones, Daniel S.; Ruf, Joseph H.; Bui, Trong T.; Martinez, Martel; St. John, Clinton W.

2014-01-01

The dual-bell rocket nozzle was first proposed in 1949, offering a potential improvement in rocket nozzle performance over the conventional-bell nozzle. Despite the performance advantages that have been predicted, both analytically and through static test data, the dual-bell nozzle has still not been adequately tested in a relevant flight environment. In 2013 a proposal was constructed that offered a NASA F-15 airplane as the flight testbed, with the plan to operate a dual-bell rocket nozzle during captive-carried flight. If implemented, this capability will permit nozzle operation into an external flow field similar to that of a launch vehicle, and facilitate an improved understanding of dual-bell nozzle plume sensitivity to external flow-field effects. More importantly, this flight testbed can be utilized to help quantify the performance benefit with the dual-bell nozzle, as well as to advance its technology readiness level. Toward this ultimate goal, this paper provides plans for future flights to quantify the external flow field of the airplane near the nozzle experiment, as well as details on the conceptual design for the dual-bell nozzle cold-flow propellant feed system integration within the NASA F-15 Propulsion Flight Test Fixture. The current study shows that this concept of flight research is feasible, and could result in valuable flight data for the dual-bell nozzle.

Use of evidence to support healthy public policy: a policy effectiveness–feasibility loop

PubMed Central

Bowman, Sarah; Critchley, Julia; Capewell, Simon; Husseini, Abdullatif; Maziak, Wasim; Zaman, Shahaduz; Ben Romdhane, Habiba; Fouad, Fouad; Phillimore, Peter; Unal, Belgin; Khatib, Rana; Shoaibi, Azza; Ahmad, Balsam

2012-01-01

Abstract Public policy plays a key role in improving population health and in the control of diseases, including non-communicable diseases. However, an evidence-based approach to formulating healthy public policy has been difficult to implement, partly on account of barriers that hinder integrated work between researchers and policy-makers. This paper describes a “policy effectiveness–feasibility loop” (PEFL) that brings together epidemiological modelling, local situation analysis and option appraisal to foster collaboration between researchers and policy-makers. Epidemiological modelling explores the determinants of trends in disease and the potential health benefits of modifying them. Situation analysis investigates the current conceptualization of policy, the level of policy awareness and commitment among key stakeholders, and what actually happens in practice, thereby helping to identify policy gaps. Option appraisal integrates epidemiological modelling and situation analysis to investigate the feasibility, costs and likely health benefits of various policy options. The authors illustrate how PEFL was used in a project to inform public policy for the prevention of cardiovascular diseases and diabetes in four parts of the eastern Mediterranean. They conclude that PEFL may offer a useful framework for researchers and policy-makers to successfully work together to generate evidence-based policy, and they encourage further evaluation of this approach. PMID:23226897

Investigating the Conceptual Variation of Major Physics Textbooks

NASA Astrophysics Data System (ADS)

Stewart, John; Campbell, Richard; Clanton, Jessica

2008-04-01

The conceptual problem content of the electricity and magnetism chapters of seven major physics textbooks was investigated. The textbooks presented a total of 1600 conceptual electricity and magnetism problems. The solution to each problem was decomposed into its fundamental reasoning steps. These fundamental steps are, then, used to quantify the distribution of conceptual content among the set of topics common to the texts. The variation of the distribution of conceptual coverage within each text is studied. The variation between the major groupings of the textbooks (conceptual, algebra-based, and calculus-based) is also studied. A measure of the conceptual complexity of the problems in each text is presented.

Investigation of the feasibility of a small scale transmutation device

NASA Astrophysics Data System (ADS)

Sit, Roger Carson

This dissertation presents the design and feasibility of a small-scale, fusion-based transmutation device incorporating a commercially available neutron generator. It also presents the design features necessary to optimize the device and render it practical for the transmutation of selected long-lived fission products and actinides. Four conceptual designs of a transmutation device were used to study the transformation of seven radionuclides: long-lived fission products (Tc-99 and I-129), short-lived fission products (Cs-137 and Sr-90), and selective actinides (Am-241, Pu-238, and Pu-239). These radionuclides were chosen because they are major components of spent nuclear fuel and also because they exist as legacy sources that are being stored pending a decision regarding their ultimate disposition. The four designs include the use of two different devices; a Deuterium-Deuterium (D-D) neutron generator (for one design) and a Deuterium-Tritium (D-T) neutron generator (for three designs) in configurations which provide different neutron energy spectra for targeting the radionuclide for transmutation. Key parameters analyzed include total fluence and flux requirements; transmutation effectiveness measured as irradiation effective half-life; and activation products generated along with their characteristics: activity, dose rate, decay, and ingestion and inhalation radiotoxicity. From this investigation, conclusions were drawn about the feasibility of the device, the design and technology enhancements that would be required to make transmutation practical, the most beneficial design for each radionuclide, the consequence of the transmutation, and radiation protection issues that are important for the conceptual design of the transmutation device. Key conclusions from this investigation include: (1) the transmutation of long-lived fission products and select actinides can be practical using a small-scale, fusion driven transmutation device; (2) the transmutation of long-lived fission products could result in an irradiation effective half-life of a few years with a three order magnitude increase in the on-target neutron flux accomplishable through a combination of technological enhancements to the source and system design optimization; (3) the transmutation of long-lived fission products requires a thermal-slow energy spectrum to prevent the generation of activation products with half-lives even longer than the original radionuclide; (4) there is no benefit in trying to transmute short-lived fission products due to the ineffectiveness of the transmutation process and the generation of a multiplicity of counterproductive activation products; (5) for actinides, irradiation effective half-lives of < 1 year can be achieved with a four orders magnitude increase in the on-target flux; (6) the ideal neutron energy spectra for transmuting actinides is highly dependent on the particular radionuclide and its fission-to-capture ratio as they determine the generationrate of other actinides; and (7) the methodology developed in this dissertation provides a mechanism that can be used for studying the feasibility of transmuting other radionuclides, and its application can be extended to studying the production of radionuclides of interest in a transmutation process. Although large-scale transmutation technology is presently being researched world-wide for spent fuel management applications, such technology will not be viable for a couple of decades. This dissertation investigated the concept of a small-scale transmutation device using present technology. The results of this research show that with reasonable enhancements, transmutation of specific radionuclides can be practical in the near term.

A hypersonic research vehicle to develop scramjet engines

NASA Technical Reports Server (NTRS)

Gregorek, G. M.; Reuss, R. L.

1990-01-01

Four student design teams produced conceptual designs for a research vehicle to develop the supersonic combustion ramjet (scramjet) engines necessary for efficient hypersonic flight. This research aircraft would provide flight test data for prototype scramjets that is not available in groundbased test facilities. The design specifications call for a research aircraft to be launched from a carrier aircraft at 40,000 feet and a Mach number of 0.8. The aircraft must accelerate to Mach 6 while climbing to a 100,000 foot altitude and then ignite the experimental scramjet engines for acceleration to Mach 10. The research vehicle must then be recovered for another flight. The students responded with four different designs, two piloted waverider configurations, and two unmanned vehicles, one with a blended body-wing configuration, the other with a delta wing shape. All aircraft made use of an engine database provided by the General Electric Aircraft Engine Group; both turbofan ramjet and scramjet engine performance using liquid hydrogen fuel was available. Explained here are the students' conceptual designs and the aerodynamic and propulsion concepts that made their designs feasible.

Preserved conceptual implicit memory for pictures in patients with Alzheimer’s disease

PubMed Central

Deason, Rebecca G.; Hussey, Erin P.; Flannery, Sean; Ally, Brandon A.

2015-01-01

The current study examined different aspects of conceptual implicit memory in patients with mild Alzheimer’s disease (AD). Specifically, we were interested in whether priming of distinctive conceptual features versus general semantic information related to pictures and words would differ for the mild AD patients and healthy older adults. In this study, 14 healthy older adults and 15 patients with mild AD studied both pictures and words followed by an implicit test section, where they were asked about distinctive conceptual or general semantic information related to the items they had previously studied (or novel items) Healthy older adults and patients with mild AD showed both conceptual priming and the picture superiority effect, but the AD patients only showed these effects for the questions focused on the distinctive conceptual information. We found that patients with mild AD showed intact conceptual picture priming in a task that required generating a response (answer) from a cue (question) for cues that focused on distinctive conceptual information. This experiment has helped improve our understanding of both the picture superiority effect and conceptual implicit memory in patients with mild AD in that these findings support the notion that conceptual implicit memory might potentially help to drive familiarity-based recognition in the face of impaired recollection in patients with mild AD. PMID:26291521

Preserved conceptual implicit memory for pictures in patients with Alzheimer's disease.

PubMed

Deason, Rebecca G; Hussey, Erin P; Flannery, Sean; Ally, Brandon A

2015-10-01

The current study examined different aspects of conceptual implicit memory in patients with mild Alzheimer's disease (AD). Specifically, we were interested in whether priming of distinctive conceptual features versus general semantic information related to pictures and words would differ for the mild AD patients and healthy older adults. In this study, 14 healthy older adults and 15 patients with mild AD studied both pictures and words followed by an implicit test section, where they were asked about distinctive conceptual or general semantic information related to the items they had previously studied (or novel items). Healthy older adults and patients with mild AD showed both conceptual priming and the picture superiority effect, but the AD patients only showed these effects for the questions focused on the distinctive conceptual information. We found that patients with mild AD showed intact conceptual picture priming in a task that required generating a response (answer) from a cue (question) for cues that focused on distinctive conceptual information. This experiment has helped improve our understanding of both the picture superiority effect and conceptual implicit memory in patients with mild AD in that these findings support the notion that conceptual implicit memory might potentially help to drive familiarity-based recognition in the face of impaired recollection in patients with mild AD. Copyright © 2015. Published by Elsevier Inc.

Conceptual fluency increases recollection: behavioral and electrophysiological evidence

PubMed Central

Wang, Wei; Li, Bingbing; Gao, Chuanji; Xu, Huifang; Guo, Chunyan

2015-01-01

It is widely established that fluency can contribute to recognition memory. Previous studies have found that enhanced fluency increases familiarity, but not recollection. The present study was motivated by a previous finding that conceptual priming affected recollection. We used event-related potentials to investigate the electrophysiological correlates of these effects with conceptually related two-character Chinese words. We found that previous conceptual priming effects on conceptual fluency only increased the incidence of recollection responses. We also found that enhanced conceptual fluency was associated with N400 attenuation, which was also correlated with the behavioral indicator of recollection. These results suggest that the N400 effect might be related to the impact of conceptual fluency on recollection recognition. These study findings provide further evidence for the relationship between fluency and recollection. PMID:26175678

Rocket experiment METS Microwave Energy Transmission in Space

NASA Astrophysics Data System (ADS)

Kaya, N.; Matsumoto, H.; Akiba, R.

A METS (Microwave Energy Transmission in Space) rocket experiment is being planned by the SPS (Solar Power Satellite) Working Group at the Institute of Space and Astronautical Science (ISAS) in Japan for the forthcoming International Space Year (ISY), 1992. The METS experiment is an advanced version of our MINIX rocket experiment. This paper describes the conceptual design for the METS rocket experiment. Aims are to verify the feasibility of a newly developed microwave energy transmission system designed for use in space and to study nonlinear effects of the microwave energy beam on space plasma. A high power microwave (936 W) will be transmitted by a new phase-array antenna from a mother rocket to a separate target (daughter rocket) through the Earth's ionospheric plasma. The active phased-array system has the capability of being able to focus the microwave energy at any spatial point by individually controlling the digital phase shifters.

A feasibility study on solar utility total energy system /SUTES/

NASA Astrophysics Data System (ADS)

Bilgen, E.

1980-11-01

A fully dedicated central receiver solar utility (CRSU) designed to meet domestic energy requirements for space heating and hot water has been synthesized and assessed at the conceptual level. The solar utility total energy system (SUTES) integrates (1) a central receiver solar utility (CRSU), (2) an electrical power generating system (EPGS), (3) a hydrogen production plant (HPP), (4) a water chilling system for cooling, heat pump system (HPS), (5) necessary thermal energy storage systems (TES), (6) a district heating and cooling system (DH&CS). All subsystems are close-coupled. Using consistent costing bases, it has been found that the SUTES concept provides energy costs which are lower than those provided by a CRSU. Representative costs are $3.14/GJ versus $8.56/GJ for 10 percent recovery factor and $12.55/GJ versus $13.47/GJ for 17.5 percent recovery factor.

Repulsive force support system feasibility study

NASA Technical Reports Server (NTRS)

Boom, R. W.; Abdelsalam, M. K.; Eyssa, Y. M.; Mcintosh, G. E.

1987-01-01

A new concept in magnetic levitation and control is introduced for levitation above a plane. A set of five vertical solenoid magnets mounted flush below the plane supports and controls the model in five degrees of freedom. The compact system of levitation coils is contained in a space 2.4 m (96 in) diameter by 1 m (40 in) deep with the top of the levitation system 0.9 m (36 in) below the center line of the suspended model. The levitated model has a permanent magnet core held in position by the five parallel superconductive solenoids symmetrically located in a circle. The control and positioning system continuously corrects for model position in five dimensions using computer current pulses superimposed on the levitation coil base currents. The conceptual designs include: superconductive and Nd-Fe-B permanent magnet model cores and levitation solenoids of either superconductive, cryoresistive, or room temperature windings.

Prediction of forces and moments for flight vehicle control effectors. Part 2: An analysis of delta wing aerodynamic control effectiveness in ground effect

NASA Technical Reports Server (NTRS)

Maughmer, Mark D.; Ozoroski, L.; Ozoroski, T.; Straussfogel, D.

1990-01-01

Many types of hypersonic aircraft configurations are currently being studied for feasibility of future development. Since the control of the hypersonic configurations throughout the speed range has a major impact on acceptable designs, it must be considered in the conceptual design stage. Here, an investigation of the aerodynamic control effectiveness of highly swept delta planforms operating in ground effect is presented. A vortex-lattice computer program incorporating a free wake is developed as a tool to calculate aerodynamic stability and control derivatives. Data generated using this program are compared to experimental data and to data from other vortex-lattice programs. Results show that an elevon deflection produces greater increments in C sub L and C sub M in ground effect than the same deflection produces out of ground effect and that the free wake is indeed necessary for good predictions near the ground.

Peer-Mediated Theatrical Engagement for Improving Reciprocal Social Interaction in Autism Spectrum Disorder

PubMed Central

Corbett, Blythe A.; Qualls, Lydia R.; Valencia, Blythe; Fecteau, Stéphanie-M.; Swain, Deanna M.

2014-01-01

The hallmark characteristic of autism spectrum disorder (ASD) is poor reciprocal social communication. Interventions designed to improve this core deficit are critically needed. Social skills interventions such as direct training, peer mediation, and video modeling have contributed to improvements in various social skills in children with ASD. This paper reviews existing social competence interventions available for children with ASD while highlighting hypothesized critical components for advancing, maintaining, and generalizing skills, which include (1) peer mediation, (2) active learning, and (3) implementation in supportive, natural contexts. As a framework for these approaches, this conceptual paper describes SENSE Theatre, a novel intervention that combines trained peers that facilitate the performance-based theatrical treatment delivered in a supportive, community-based environment. A review of previous research shows early feasibility, setting the stage for more rigorous studies to aid in developing a standardized intervention package. PMID:25346926

Disaster warning system: Satellite feasibility and comparison with terrestrial systems. Volume 1: Executive summary

NASA Technical Reports Server (NTRS)

Spoor, J. H.; Hodge, W. H.; Fluk, M. J.; Bamford, T. F.

1974-01-01

The Disaster Warning System (DWS) is a conceptual system which will provide the National Weather Service (NWS) with communication services in the 1980s to help minimize losses caused by natural disasters. The object of this study is a comparative analysis between a terrestrial DWS and a satellite DWS. Baseline systems satisfying the NOAA requirements were synthesized in sufficient detail so that a comparison could be made in terms of performance and cost. The cost of both baseline systems is dominated by the disaster warning and spotter reporting functions. An effort was undertaken to reduce system cost through lower-capacity alternative systems generated by modifying the baseline systems. By reducing the number of required channels and modifying the spotter reporting techniques, alternative satellite systems were synthesized. A terrestrial alternative with the coverage reduced to an estimated 95 percent of the population was considered.

A Preliminary Foil Gas Bearing Performance Map

NASA Technical Reports Server (NTRS)

DellaCorte, Christopher; Radil, Kevin C.; Bruckner, Robert J.; Howard, S. Adam

2006-01-01

Recent breakthrough improvements in foil gas bearing load capacity, high temperature tribological coatings and computer based modeling have enabled the development of increasingly larger and more advanced Oil-Free Turbomachinery systems. Successful integration of foil gas bearings into turbomachinery requires a step wise approach that includes conceptual design and feasibility studies, bearing testing, and rotor testing prior to full scale system level demonstrations. Unfortunately, the current level of understanding of foil gas bearings and especially their tribological behavior is often insufficient to avoid developmental problems thereby hampering commercialization of new applications. In this paper, a new approach loosely based upon accepted hydrodynamic theory, is developed which results in a "Foil Gas Bearing Performance Map" to guide the integration process. This performance map, which resembles a Stribeck curve for bearing friction, is useful in describing bearing operating regimes, performance safety margins, the effects of load on performance and limiting factors for foil gas bearings.

Solid Oxide Fuel Cell Hybrid System for Distributed Power Generation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nguyen Minh

2002-03-31

This report summarizes the work performed by Honeywell during the January 2002 to March 2002 reporting period under Cooperative Agreement DE-FC26-01NT40779 for the U. S. Department of Energy, National Energy Technology Laboratory (DOE/NETL) entitled ''Solid Oxide Fuel Cell Hybrid System for Distributed Power Generation''. The main objective of this project is to develop and demonstrate the feasibility of a highly efficient hybrid system integrating a planar Solid Oxide Fuel Cell (SOFC) and a turbogenerator. For this reporting period the following activities have been carried out: {lg_bullet} Conceptual system design trade studies were performed {lg_bullet} System-level performance model was created {lg_bullet}more » Dynamic control models are being developed {lg_bullet} Mechanical properties of candidate heat exchanger materials were investigated {lg_bullet} SOFC performance mapping as a function of flow rate and pressure was completed« less

Design study of wind turbines, 50 kW to 3000 kW for electric utility applications: Executive summary

NASA Technical Reports Server (NTRS)

1977-01-01

Preliminary designs of low power (50 to 500 kW) and high power (500 to 3000 kW) wind generator systems (WGS) for electric utility applications were developed. These designs provide the bases for detail design, fabrication, and experimental demonstration testing of these units at selected utility sites. Several feasible WGS configurations were evaluated, and the concept offering the lowest energy cost potential and minimum technical risk for utility applications was selected. The selected concept was optimized utilizing a parametric computer program prepared for this purpose. The utility requirements evaluation task examined the economic, operational and institutional factors affecting the WGS in a utility environment, and provided additional guidance for the preliminary design effort. Results of the conceptual design task indicated that a rotor operating at constant speed, driving an AC generator through a gear transmission is the most cost effective WGS configuration.

Developing a military nurse scientist program of research: A military women's health exemplar.

PubMed

Trego, Lori Lyn

Developing a feasible, fundable, and sustainable program of research (POR) is an essential career goal in research. Nurse scientists can lay the foundation for a salient POR as early as during their doctoral studies. The ensuing years of postdoctoral experiences are informative as they expand their research skills and knowledge around their research area of interest. Following graduation from a doctoral research program, novice military nurse scientists (MNS) are placed in positions that are conducive to fostering a POR. Military organizational support and the rich experiences of peers and mentors facilitate early career development of MNS. The purpose of this article is to present a conceptual framework for research career development of the novice MNS. Using an exemplar POR in military women's health, the concepts are operationalized to illustrate how the military environment enhances the development of a successful POR. Copyright © 2017 Elsevier Inc. All rights reserved.

Searching for evidence of curricular effect on the teaching and learning of mathematics: some insights from the LieCal project

NASA Astrophysics Data System (ADS)

Cai, Jinfa

2014-12-01

Drawing on evidence from the Longitudinal Investigation of the Effect of Curriculum on Algebra Learning (LieCal) Project, issues related to mathematics curriculum reform and student learning are discussed. The LieCal Project was designed to longitudinally investigate the impact of a reform mathematics curriculum called the Connected Mathematics Project (CMP) in the USA on teachers' teaching and students' learning. Using a three-level conceptualization of curriculum (intended, implemented, and attained), a variety of evidence from the LieCal Project is presented to show the impact of mathematics curriculum reform on teachers' teaching and students' learning. This paper synthesizes findings from the two longitudinal studies spanning 7 years of the LieCal Project both to show the kind of impact curriculum has on teachers' teaching and students' learning and to suggest powerful but feasible ways researchers can investigate curriculum effect on both teaching and learning.

Feasibility Study of Solar Dome Encapsulation of Photovoltaic Arrays

NASA Technical Reports Server (NTRS)

1978-01-01

The technical and economic advantages of using air-supported plastic enclosures to protect flat plate photovoltaic arrays are described. Conceptual designs for a fixed, latitude-tilt array and a fully tracking array were defined. Detailed wind loads and strength analyses were performed for the fixed array. Detailed thermal and power output analyses provided array performance for typical seasonal and extreme temperature conditions. Costs of each design as used in a 200 MWe central power station were defined from manufacturing and material cost estimates. The capital cost and cost of energy for the enclosed fixed-tilt array were lower than for the enclosed tracking array. The enclosed fixed-tilt array capital investment was 38% less, and the levelized bus bar energy cost was 26% less than costs for a conventional, glass-encapsulated array design. The predicted energy cost for the enclosed fixed array was 79 mills/kW-h for direct current delivered to the power conditioning units.

Entangled Parametric Hierarchies: Problems for an Overspecified Universal Grammar

PubMed Central

Boeckx, Cedric; Leivada, Evelina

2013-01-01

This study addresses the feasibility of the classical notion of parameter in linguistic theory from the perspective of parametric hierarchies. A novel program-based analysis is implemented in order to show certain empirical problems related to these hierarchies. The program was developed on the basis of an enriched data base spanning 23 contemporary and 5 ancient languages. The empirical issues uncovered cast doubt on classical parametric models of language acquisition as well as on the conceptualization of an overspecified Universal Grammar that has parameters among its primitives. Pinpointing these issues leads to the proposal that (i) the (bio)logical problem of language acquisition does not amount to a process of triggering innately pre-wired values of parameters and (ii) it paves the way for viewing language, epigenetic (‘parametric’) variation as an externalization-related epiphenomenon, whose learning component may be more important than what sometimes is assumed. PMID:24019867

Study of reactor Brayton power systems for nuclear electric spacecraft

NASA Technical Reports Server (NTRS)

1979-01-01

The feasibility of using Brayton power systems for nuclear electric spacecraft was investigated. The primary performance parameters of systems mass and radiator area were determined for systems from 100 to 1000 kW sub e. Mathematical models of all system components were used to determine masses and volumes. Two completely independent systems provide propulsion power so that no single-point failure can jeopardize a mission. The waste heat radiators utilize armored heat pipes to limit meteorite puncture. The armor thickness was statistically determined to achieve the required probability of survival. A 400 kW sub e reference system received primary attention as required by the contract. The components of this system were defined and a conceptual layout was developed with encouraging results. An arrangement with redundant Brayton power systems having a 1500 K (2240 F) turbine inlet temperature was shown to be compatible with the dimensions of the space shuttle orbiter payload bay.

Sodium-NaK engineering handbook. Volume III. Sodium systems, safety, handling, and instrumentation. [LMFBR

DOE Office of Scientific and Technical Information (OSTI.GOV)

Foust, O J

1978-01-01

The handbook is intended for use by present and future designers in the Liquid Metals Fast Breeder Reactor (LMFBR) Program and by the engineering and scientific community performing other type investigation and exprimentation requiring high-temperature sodium and NaK technology. The arrangement of subject matter progresses from a technological discussion of sodium and sodium--potassium alloy (NaK) to discussions of varius categories and uses of hardware in sodium and NaK systems. Emphasis is placed on sodium and NaK as heat-transport media. Sufficient detail is included for basic understanding of sodium and NaK technology and of technical aspects of sodium and NaK componentsmore » and instrument systems. Information presented is considered adequate for use in feasibility studies and conceptual design, sizing components and systems, developing preliminary component and system descriptions, identifying technological limitations and problem areas, and defining basic constraints and parameters.« less

Balancing efficiency, equity and feasibility of HIV treatment in South Africa – development of programmatic guidance

PubMed Central

2013-01-01

South Africa, the country with the largest HIV epidemic worldwide, has been scaling up treatment since 2003 and is rapidly expanding its eligibility criteria. The HIV treatment programme has achieved significant results, and had 1.8 million people on treatment per 2011. Despite these achievements, it is now facing major concerns regarding (i) efficiency: alternative treatment policies may save more lives for the same budget; (ii) equity: there are large inequalities in who receives treatment; (iii) feasibility: still only 52% of the eligible population receives treatment. Hence, decisions on the design of the present HIV treatment programme in South Africa can be considered suboptimal. We argue there are two fundamental reasons to this. First, while there is a rapidly growing evidence-base to guide priority setting decisions on HIV treatment, its included studies typically consider only one criterion at a time and thus fail to capture the broad range of values that stakeholders have. Second, priority setting on HIV treatment is a highly political process but it seems no adequate participatory processes are in place to incorporate stakeholders’ views and evidences of all sorts. We propose an alternative approach that provides a better evidence base and outlines a fair policy process to improve priority setting in HIV treatment. The approach integrates two increasingly important frameworks on health care priority setting: accountability for reasonableness (A4R) to foster procedural fairness, and multi-criteria decision analysis (MCDA) to construct an evidence-base on the feasibility, efficiency, and equity of programme options including trade-offs. The approach provides programmatic guidance on the choice of treatment strategies at various decisions levels based on a sound conceptual framework, and holds large potential to improve HIV priority setting in South Africa. PMID:24107435

Reactor/Brayton power systems for nuclear electric spacecraft

NASA Technical Reports Server (NTRS)

Layton, J. P.

1980-01-01

Studies are currently underway to assess the technological feasibility of a nuclear-reactor-powered spacecraft propelled by electric thrusters. This vehicle would be capable of performing detailed exploration of the outer planets of the solar system during the remainder of this century. The purpose of this study was to provide comparative information on a closed cycle gas turbine power conversion system. The results have shown that the performance is very competitive and that a 400 kWe space power system is dimensionally compatible with a single Space Shuttle launch. Performance parameters of system mass and radiator area were determined for systems from 100 to 1000 kWe. A 400 kWe reference system received primary attention. The components of this system were defined and a conceptual layout was developed with encouraging results. The preliminary mass determination for the complete power system was very close to the desired goal of 20 kg/kWe. Use of more advanced technology (higher turbine inlet temperature) will substantially improve system performance characteristics.

Volumetric integration of functions for a long term initial Mars habitat

NASA Astrophysics Data System (ADS)

Gutierrez, David John

Sucessfully planning a manned mission to Mars involves an extraordinary balance of resources, risk, technology development and innovation. The interdependency of these factors will ultimately drive out more feasible scenarios for supporting humans during three year, or longer, missions to the Mars surface and home to Earth. Based on a mission profile developed in the Exploration Programs Office at the Johnson Space Center, the Flight Crew Support division began developing conceptual Mars surface habitats to drive out the early human support issues and habitat development concerns. Following the completion of an analysis of a horizontally oriented and outfitted Initial Lunar Haitat (ILH), the decision was made to focus on a vertically oriented habitat as a comparative study. Drawing from the results of both KC-135 partial gravity locomotion testing and water immersion vertical translation studies, the Initial Mars Habitat (IMH), is an analysis of the habitat systems, volumes, and capabilities required to support the first crew of six on the surface of Mars for 500 to 600 days.

Nuclear medicine and quantitative imaging research (quantitative studies in radiopharmaceutical science): Comprehensive progress report, April 1, 1986-December 31, 1988

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cooper, M.D.; Beck, R.N.

1988-06-01

This document describes several years research to improve PET imaging and diagnostic techniques in man. This program addresses the problems involving the basic science and technology underlying the physical and conceptual tools of radioactive tracer methodology as they relate to the measurement of structural and functional parameters of physiologic importance in health and disease. The principal tool is quantitative radionuclide imaging. The overall objective of this program is to further the development and transfer of radiotracer methodology from basic theory to routine clinical practice in order that individual patients and society as a whole will receive the maximum net benefitmore » from the new knowledge gained. The focus of the research is on the development of new instruments and radiopharmaceuticals, and the evaluation of these through the phase of clinical feasibility. The reports in the study were processed separately for the data bases. (TEM)« less

The interaction of high voltage systems with the environments of the Moon and Mars

NASA Technical Reports Server (NTRS)

Hillard, G. Barry; Kolecki, Joseph C.

1993-01-01

High voltage systems designed for use on the lunar and Martian surfaces or in orbit will interact with environmental components such as electrically charged dust, low pressure atmospheres, ionospheric plasmas and neutrals, and chemically reactive species. As the Space Exploration Initiative (SEI) advances from the realm of feasibility study to that of conceptual design, guidelines will be required to ensure that these effects are properly accounted for. A first step in providing such guidelines is the prioritization of interactions for each of the space or surface environments that will be encountered. For those issues that are identified as high priority, the state of environmental knowledge, emphasizing essential data, must be determined. This report describes possible means of obtaining such information, including ground tests, modeling and analysis, and flight experiments. The development of computational tools which will enable engineers to simulate and thereby quantify the interactions will be especially considered. Our analysis is drawn from various study and workshop activities undertaken within the last two years.

Preliminary design of a solar central receiver for site-specific repowering application (Saguaro Power Plant). Volume II. Preliminary design. Final report, October 1982-September 1983

DOE Office of Scientific and Technical Information (OSTI.GOV)

Weber, E.R.

1983-09-01

The solar central receiver technology, site, and specific unit for repowering were selected in prior analyses and studies. The objectives of this preliminary design study were to: develop a solar central receiver repowering design for Saguaro that (1) has potential to be economically competitive with fossil fueled plants in near and long term applications, (2) has the greatest chance for completion without further government funding, (3) will further define technical and economic feasibility of a 66 MWe gross size plant that is adequate to meet the requirements for utility and industrial process heat applications, (4) can potentially be constructed andmore » operated within the next five years, and (5) incorporates solar central receiver technology and represents state-of-the-art development. This volume on the preliminary design includes the following sections: executive summary; introduction; changes from advanced conceptual design; preliminary design; system characteristics; economic analysis; and development plan.« less

Cancer therapy in the necroptosis era

PubMed Central

Su, Z; Yang, Z; Xie, L; DeWitt, J P; Chen, Y

2016-01-01

Necroptosis is a caspase-independent form of regulated cell death executed by the receptor-interacting protein kinase 1 (RIP1), RIP3, and mixed lineage kinase domain-like protein (MLKL). Recently, necroptosis-based cancer therapy has been proposed to be a novel strategy for antitumor treatment. However, a big controversy exists on whether this type of therapy is feasible or just a conceptual model. Proponents believe that because necroptosis and apoptosis use distinct molecular pathways, triggering necroptosis could be an alternative way to eradicate apoptosis-resistant cancer cells. This hypothesis has been preliminarily validated by recent studies. However, some skeptics doubt this strategy because of the intrinsic or acquired defects of necroptotic machinery observed in many cancer cells. Moreover, two other concerns are whether or not necroptosis inducers are selective in killing cancer cells without disturbing the normal cells and whether it will lead to inflammatory diseases. In this review, we summarize current studies surrounding this controversy on necroptosis-based antitumor research and discuss the advantages, potential issues, and countermeasures of this novel therapy. PMID:26915291

Feasibility of a far infrared laser based polarimeter diagnostic system for the JT-60SA fusion experiment

NASA Astrophysics Data System (ADS)

Boboc, A.; Gil, C.; Terranova, D.; Orsitto, F. P.; Soare, S.; Lotte, P.; Sozzi, C.; Imazawa, R.; Kubo, H.

2018-07-01

JT-60SA is the large Tokamak device that is being built in Japan under the Broader Approach Satellite Tokamak Programme and the Japanese National Programme and will operate as a satellite machine for ITER. The main goal of the JT-60SA Programme is to provide valuable information for the ITER steady-state scenario and for the design of DEMO, where the real-time control of the safety factor profile is very important, in connection with both MHD stability and plasma confinement. It has been demonstrated in this work that to this end polarimetry measurements are necessary, in particular in order to reconstruct the safety factor profile in reversed shear scenarios. In this paper we present the main steps of a conceptual feasibility study of a multi-channel polarimeter diagnostic and the resulting optimised geometry. In this study, magnetic scenario modelling, a realistic CAD-driven design and long-term operation requirements, rarely even considered at this stage, have been considered. It is shown that a far infrared polarimeter system, with a laser operating at a wavelength of 194.7 μm and up to twelve channels can be envisaged for JT-60SA. The top requirements can be attained, i.e., that the polarimeter, together with other diagnostic measurements, should provide q-profile reconstruction with an accuracy of 10% for the entire plasma cycle and suitable time resolution for real-time applications, in particular in high density and ITER-relevant plasma scenarios.

Case conceptualization research in cognitive behavior therapy: A state of the science review.

PubMed

Easden, Michael H; Kazantzis, Nikolaos

2018-03-01

Prominent models of cognitive behavior therapy (CBT) assert that case conceptualization is crucial for tailoring interventions to adequately address the needs of the individual client. We aimed to review the research on case conceptualization in CBT. We conducted a systematic search of PsychINFO, MEDLINE, Psychology and Behavioral Science Collection, and CINAHL databases to February 2016. A total of 24 studies that met inclusion criteria were identified. It was notable that studies (a) focused on the assessment function of case conceptualization, (b) employed diverse methodologies, and, overall, (c) there remains a paucity of studies examining the in-session process of using case conceptualization or examining relations with outcome. Results from the existing studies suggest that experienced therapists can reliably construct some elements of case conceptualizations, but importance for the efficacy of case conceptualization in CBT has yet to be demonstrated. Research that involves direct observation of therapist competence in case conceptualization as a predictor of CBT outcomes is recommended as a focus for future hypothesis testing. © 2017 Wiley Periodicals, Inc.

Feasibilities of a Coal-Biomass to Liquids Plant in Southern West Virginia

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bhattacharyya, Debangsu; DVallance, David; Henthorn, Greg

This project has generated comprehensive and realistic results of feasibilities for a coal-biomass to liquids (CBTL) plant in southern West Virginia; and evaluated the sensitivity of the analyses to various anticipated scenarios and parametric uncertainties. Specifically the project has addressed economic feasibility, technical feasibility, market feasibility, and financial feasibility. In the economic feasibility study, a multi-objective siting model was developed and was then used to identify and rank the suitable facility sites. Spatial models were also developed to assess the biomass and coal feedstock availabilities and economics. Environmental impact analysis was conducted mainly to assess life cycle analysis and greenhousemore » gas emission. Uncertainty and sensitivity analysis were also investigated in this study. Sensitivity analyses on required selling price (RSP) and greenhouse gas (GHG) emissions of CBTL fuels were conducted according to feedstock availability and price, biomass to coal mix ratio, conversion rate, internal rate of return (IRR), capital cost, operational and maintenance cost. The study of siting and capacity showed that feedstock mixed ratio limited the CBTL production. The price of coal had a more dominant effect on RSP than that of biomass. Different mix ratios in the feedstock and conversion rates led to RSP ranging from $104.3 - $157.9/bbl. LCA results indicated that GHG emissions ranged from 80.62 kg CO 2 eq to 101.46 kg CO2 eq/1,000 MJ of liquid fuel at various biomass to coal mix ratios and conversion rates if carbon capture and storage (CCS) was applied. Most of water and fossil energy were consumed in conversion process. Compared to petroleum-derived-liquid fuels, the reduction in GHG emissions could be between -2.7% and 16.2% with CBTL substitution. As for the technical study, three approaches of coal and biomass to liquids, direct, indirect and hybrid, were considered in the analysis. The process models including conceptual design, process modeling and process validation were developed and validated for different cases. Equipment design and capital costs were investigated on capital coast estimation and economical model validation. Material and energy balances and techno-economic analysis on base case were conducted for evaluation of projects. Also, sensitives studies of direct and indirect approaches were both used to evaluate the CBTL plant economic performance. In this study, techno-economic analysis were conducted in Aspen Process Economic Analyzer (APEA) environment for indirect, direct, and hybrid CBTL plants with CCS based on high fidelity process models developed in Aspen Plus and Excel. The process thermal efficiency ranges from 45% to 67%. The break-even oil price ranges from $86.1 to $100.6 per barrel for small scale (10000 bbl/day) CBTL plants and from $65.3 to $80.5 per barrel for large scale (50000 bbl/day) CBTL plants. Increasing biomass/coal ratio from 8/92 to 20/80 would increase the break-even oil price of indirect CBTL plant by $3/bbl and decrease the break-even oil price of direct CBTL plant by about $1/bbl. The order of carbon capture penalty is direct > indirect > hybrid. The order of capital investment is hybrid (with or without shale gas utilization) > direct (without shale gas utilization) > indirect > direct (with shale gas utilization). The order of thermal efficiency is direct > hybrid > indirect. The order of break-even oil price is hybrid (without shale gas utilization) > direct (without shale gas utilization) > hybrid (with shale gas utilization) > indirect > direct (with shale gas utilization).« less

The conceptualization model problem—surprise

NASA Astrophysics Data System (ADS)

Bredehoeft, John

2005-03-01

The foundation of model analysis is the conceptual model. Surprise is defined as new data that renders the prevailing conceptual model invalid; as defined here it represents a paradigm shift. Limited empirical data indicate that surprises occur in 20-30% of model analyses. These data suggest that groundwater analysts have difficulty selecting the appropriate conceptual model. There is no ready remedy to the conceptual model problem other than (1) to collect as much data as is feasible, using all applicable methods—a complementary data collection methodology can lead to new information that changes the prevailing conceptual model, and (2) for the analyst to remain open to the fact that the conceptual model can change dramatically as more information is collected. In the final analysis, the hydrogeologist makes a subjective decision on the appropriate conceptual model. The conceptualization problem does not render models unusable. The problem introduces an uncertainty that often is not widely recognized. Conceptual model uncertainty is exacerbated in making long-term predictions of system performance. C'est le modèle conceptuel qui se trouve à base d'une analyse sur un modèle. On considère comme une surprise lorsque le modèle est invalidé par des données nouvelles; dans les termes définis ici la surprise est équivalente à un change de paradigme. Des données empiriques limitées indiquent que les surprises apparaissent dans 20 à 30% des analyses effectuées sur les modèles. Ces données suggèrent que l'analyse des eaux souterraines présente des difficultés lorsqu'il s'agit de choisir le modèle conceptuel approprié. Il n'existe pas un autre remède au problème du modèle conceptuel que: (1) rassembler autant des données que possible en utilisant toutes les méthodes applicables—la méthode des données complémentaires peut conduire aux nouvelles informations qui vont changer le modèle conceptuel, et (2) l'analyste doit rester ouvert au fait que le modèle conceptuel peut bien changer lorsque des nouvelles informations apparaissent. Dans l'analyse finale le hydrogéologue prend une décision subjective sur le modèle conceptuel approprié. Le problème du le modèle conceptuel ne doit pas rendre le modèle inutilisable. Ce problème introduit une incertitude qui n'est pas toujours reconnue. Les incertitudes du modèle conceptuel deviennent plus importantes dans les cases de prévisions à long terme dans l'analyse de performance. La base para hacer un análisis de un modelo es el modelo conceptual. Se define aquí la sorpresa como los datos nuevos que convierten en incoherente al modelo conceptual previamente aceptado; tal como se define aquí esto representa un cambio de paradigma. Los datos empíricos limitados indican que estas sorpresas suceden entre un 20 a un 30% de los análisis de modelos. Esto sugiere que los analistas de modelos de agua subterránea tienen dificultades al seleccionar el modelo conceptual apropiado. No hayotra solución disponible a este problema del modelo conceptual diferente de: (1) Recolectar tanta información como sea posible, mediante la utilización de todos los métodos aplicables, lo cual puede resultar en que esta nueva información ayude a cambiar el modelo conceptual vigente, y (2) Que el analista de modelos se mantenga siempre abierto al hecho de que un modelo conceptual puede cambiar de manera total, en la medida en que se colecte mas información. En el análisis final el hidrogeólogo toma una decisión subjetiva en cuanto al modelo conceptual apropiado. El problema de la conceptualización no produce modelos inútiles. El problema presenta una incertidumbre, la cual a menudo no es tenida en cuentade manera adecuada. Esta incertidumbre en los modelos conceptuales se aumenta, cuando se hacen predicciones a largo plazo del comportamiento de un sistema dado.

Community‐Academic Partnerships: A Systematic Review of the State of the Literature and Recommendations for Future Research

PubMed Central

MEZA, ROSEMARY D.; BRIKHO, BRIGITTE; NAAF, MEGHAN; ESTABILLO, JASPER A.; GOMEZ, EMILY D.; VEJNOSKA, SARAH F.; DUFEK, SARAH; STAHMER, AUBYN C.; AARONS, GREGORY A.

2016-01-01

Policy Points: Communities, funding agencies, and institutions are increasingly involving community stakeholders as partners in research, to provide firsthand knowledge and insight.Based on our systematic review of major literature databases, we recommend using a single term, community‐academic partnership (CAP), and a conceptual definition to unite multiple research disciplines and strengthen the field.Interpersonal and operational factors that facilitate or hinder the collaborative process have been consistently identified, including “trust among partners” and “respect among partners” (facilitating interpersonal factors) and “excessive time commitment” (hindering operational factor).Once CAP processes and characteristics are better understood, the effectiveness of collaborative partner involvement can be tested. Context Communities, funding agencies, and institutions are increasingly involving community stakeholders as partners in research. Community stakeholders can provide firsthand knowledge and insight, thereby increasing research relevance and feasibility. Despite the greater emphasis and use of community‐academic partnerships (CAP) across multiple disciplines, definitions of partnerships and methodologies vary greatly, and no systematic reviews consolidating this literature have been published. The purpose of this article, then, is to facilitate the continued growth of this field by examining the characteristics of CAPs and the current state of the science, identifying the facilitating and hindering influences on the collaborative process, and developing a common term and conceptual definition for use across disciplines. Methods Our systematic search of 6 major literature databases generated 1,332 unique articles, 50 of which met our criteria for inclusion and provided data on 54 unique CAPs. We then analyzed studies to describe CAP characteristics and to identify the terms and methods used, as well as the common influences on the CAP process and distal outcomes. Findings CAP research spans disciplines, involves a variety of community stakeholders, and focuses on a large range of study topics. CAP research articles, however, rarely report characteristics such as membership numbers or duration. Most studies involved case studies using qualitative methods to collect data on the collaborative process. Although various terms were used to describe collaborative partnerships, few studies provided conceptual definitions. Twenty‐three facilitating and hindering factors influencing the CAP collaboration process emerged from the literature. Outcomes from the CAPs most often included developing or refining tangible products. Conclusions Based on our systematic review, we recommend using a single term, community‐academic partnership, as well as a conceptual definition to unite multiple research disciplines. In addition, CAP characteristics and methods should be reported more systematically to advance the field (eg, to develop CAP evaluation tools). We have identified the most common influences that facilitate and hinder CAPs, which in turn should guide their development and sustainment. PMID:26994713

Sustainability assessment through analogical models: The approach of aerobic living-organism

NASA Astrophysics Data System (ADS)

Dassisti, Michele

2014-10-01

The most part of scientific discoveries of human being borrow ideas and inspiration from nature. This point gives the rationale of the sustainability assessment approach presented here and based on the aerobic living organism (ALO) already developed by the author, which funds on the basic assumption that it is reasonable and effective to refer to the analogy between an system organized by human (say, manufacturing system, enterprise, etc.) for several decision-making scopes. The critical review of the ALO conceptual model already developed is here discussed through an example of an Italian small enterprise manufacturing metal components for civil furniture to assess its feasibility for sustainability appraisal.

The samara spacecraft: Design and development of a self-stabilizing, auto-rotating, distributed sensing system

NASA Astrophysics Data System (ADS)

Lalloobhai, Amit Desai

The objective of this research is the design and development of a self-stabilizing re-entry vehicle that closely resembles naturally occurring seeds in nature. It was hypothesized that a femto-satellite with a shape of a samara could self stabilize and passively generate lift, as well as transmit a signal during its descent through the atmosphere. The research included a conceptual design phase and a preliminary design phase that entailed analytic simulations, and an experimental demonstration. The goal was to investigate the feasibility of developing the above-mentioned femto-vehicle that could increase the range capability of its descent to maximize data capture.

Arusha Rover Deployable Medical Workstation

NASA Technical Reports Server (NTRS)

Boswell, Tyrone; Hopson, Sonya; Marzette, Russell; Monroe, Gilena; Mustafa, Ruqayyah

2014-01-01

The NSBE Arusha rover concept offers a means of human transport and habitation during long-term exploration missions on the moon. This conceptual rover calls for the availability of medical supplies and equipment for crew members in order to aid in mission success. This paper addresses the need for a dedicated medical work station aboard the Arusha rover. The project team investigated multiple options for implementing a feasible deployable station to address both the medical and workstation layout needs of the rover and crew. Based on layout specifications and medical workstation requirements, the team has proposed a deployable workstation concept that can be accommodated within the volumetric constraints of the Arusha rover spacecraft

Creative conceptual expansion: A combined fMRI replication and extension study to examine individual differences in creativity.

PubMed

Abraham, Anna; Rutter, Barbara; Bantin, Trisha; Hermann, Christiane

2018-05-05

The aims of this fMRI study were two-fold. The first objective of the study was to verify whether the findings associated with a previous fMRI study could be replicated in which a novel event-related experimental design was developed which rendered it possible to investigate the brain basis of creative conceptual expansion. The ability to widen the boundaries of conceptual structures is integral to creative idea generation, which makes conceptual expansion a core component of creative cognition. Creative conceptual expansion led to the engagement of brain regions that are known to be involved in the access, storage and relational integration of conceptual knowledge in the original study. These included the anterior inferior frontal gyrus, the temporal poles and the lateral frontal pole. These findings in relation to the brain basis of creative conceptual expansion were replicated in the current study. The second objective of this study was to evaluate the brain basis of individual differences in creative conceptual expansion. The high creative group relative to the low creative group was shown to exhibit greater activity in regions of the semantic cognition network as well as the salience network during creative conceptual expansion. The findings are discussed from the point of view of classical hypotheses about information processing biases that explain individual differences in creativity including flat associative hierarchies, defocused attention and cognitive disinhibition. Copyright © 2018 Elsevier Ltd. All rights reserved.

US defense policy, US Air Force doctrine and strategic nuclear weapon systems, 1958-1964: the case of the Minuteman ICBM

DOE Office of Scientific and Technical Information (OSTI.GOV)

Reed, G.A.

This study examines the efforts of the US Air Force during 1958-1964 to develop doctrine for strategic nuclear weapon systems. These years were characterized by rapid, extensive change in the technology of nuclear weapons delivery systems, centering in ICBMs replacing bombers as the chief vehicles. Simultaneously, national military strategy changed with the transfer of power from the Eisenhower to the Kennedy Administrations, shifting from reliance on overwhelming nuclear retaliation to emphasis on balanced conventional and nuclear forces. Against this background, the study poses the question: did the Air Force, when confronted with major changes in technology and national policy, developmore » doctrine for strategic nuclear weapon systems that was politically acceptable, technically feasible, and strategically sound. Using the development of the Minuteman ICBM as a case study, the study examines the evolution of Air Force doctrine and concludes that the Air Force did not, because of conceptual problems and bureaucratic exigencies, develop a doctrine adequate to the requirements of deterrence in the dawning era of solid-fuel ICBMs.« less

The Impact of the Security Competency on "Self-Efficacy in Information Security" for Effective Health Information Security in Iran.

PubMed

Shahri, Ahmad Bakhtiyari; Ismail, Zuraini; Mohanna, Shahram

2016-11-01

The security effectiveness based on users' behaviors is becoming a top priority of Health Information System (HIS). In the first step of this study, through the review of previous studies 'Self-efficacy in Information Security' (SEIS) and 'Security Competency' (SCMP) were identified as the important factors to transforming HIS users to the first line of defense in the security. Subsequently, a conceptual model was proposed taking into mentioned factors for HIS security effectiveness. Then, this quantitative study used the structural equation modeling to examine the proposed model based on survey data collected from a sample of 263 HIS users from eight hospitals in Iran. The result shows that SEIS is one of the important factors to cultivate of good end users' behaviors toward HIS security effectiveness. However SCMP appears a feasible alternative to providing SEIS. This study also confirms the mediation effects of SEIS on the relationship between SCMP and HIS security effectiveness. The results of this research paper can be used by HIS and IT managers to implement their information security process more effectively.

Conceptual Launch Vehicles Using Metallic Hydrogen Propellant

NASA Astrophysics Data System (ADS)

Cole, John W.; Silvera, Isaac F.; Foote, John P.

2008-01-01

Solid molecular hydrogen is predicted to transform into an atomic solid with metallic properties under pressures >4.5 Mbar. Atomic metallic hydrogen is predicted to be metastable, limited by some critical temperature and pressure, and to store very large amounts of energy. Experiments may soon determine the critical temperature, critical pressure, and specific energy availability. It is useful to consider the feasibility of using metastable atomic hydrogen as a rocket propellant. If one assumes that metallic hydrogen is stable at usable temperatures and pressures, and that it can be affordably produced, handled, and stored, then it may be a useful rocket propellant. Assuming further that the available specific energy can be determined from the recombination of the atoms into molecules (216 MJ/kg), then conceptual engines and launch vehicle concepts can be developed. Under these assumptions, metallic hydrogen would be a revolutionary new rocket fuel with a theoretical specific impulse of 1700 s at a chamber pressure of 100 atm. A practical problem that arises is that rocket chamber temperatures may be too high for the use of this pure fuel. This paper examines an engine concept that uses liquid hydrogen or water as a diluent coolant for the metallic hydrogen to reduce the chamber temperature to usable values. Several launch vehicles are then conceptually developed. Results indicate that if metallic hydrogen is experimentally found to have the properties assumed in this analysis, then there are significant benefits. These benefits become more attractive as the chamber temperatures increase.

A closed-loop air revitalization process technology demonstrator

NASA Astrophysics Data System (ADS)

Mulloth, Lila; Perry, Jay; Luna, Bernadette; Kliss, Mark

Demonstrating a sustainable, reliable life support system process design that possesses the capability to close the oxygen cycle to the greatest extent possible is required for extensive surface exploration of the Moon and Mars by humans. A conceptual closed-loop air revitalization system process technology demonstrator that combines the CO2 removal, recovery, and reduction and oxygen generation operations in a single compact envelope is described. NASA has developed, and in some cases flown, process technologies for capturing metabolic CO2 from air, reducing CO2 to H2O and CH4, electrolyzing H2O to O2, and electrolyzing CO2 to O2 and CO among a number of candidates. Traditionally, these processes either operate in parallel with one another or have not taken full benefit of a unit operation-based design approach to take complete advantage of the synergy between individual technologies. The appropriate combination of process technologies must capitalize on the advantageous aspects of individual technologies while eliminating or transforming the features that limit their feasibility when considered alone. Such a process technology integration approach also provides advantages of optimized mass, power and volume characteristics for the hardware embodiment. The conceptual air revitalization system process design is an ideal technology demonstrator for the critically needed closed-loop life support capabilities for long duration human exploration of the lunar surface and extending crewed space exploration toward Mars. The conceptual process design incorporates low power CO2 removal, process gas drying, and advanced engineered adsorbents being developed by NASA and industry.

Conceptual Teaching Based on Scientific Storyline Method and Conceptual Change Texts: Latitude-Parallel Concepts

ERIC Educational Resources Information Center

Uzunöz, Abdulkadir

2018-01-01

The purpose of this study is to identify the conceptual mistakes frequently encountered in teaching geography such as latitude-parallel concepts, and to prepare conceptual change text based on the Scientific Storyline Method, in order to resolve the identified misconceptions. In this study, the special case method, which is one of the qualitative…

Conceptual Change Texts in Chemistry Teaching: A Study on the Particle Model of Matter

ERIC Educational Resources Information Center

Beerenwinkel, Anne; Parchmann, Ilka; Grasel, Cornelia

2011-01-01

This study explores the effect of a conceptual change text on students' awareness of common misconceptions on the particle model of matter. The conceptual change text was designed based on principles of text comprehensibility, of conceptual change instruction and of instructional approaches how to introduce the particle model. It was evaluated in…

Exploring Grade 11 Students' Conceptual Pathways of the Particulate Nature of Matter in the Context of Multirepresentational Instruction

ERIC Educational Resources Information Center

Adadan, Emine; Trundle, Kathy Cabe; Irving, Karen E.

2010-01-01

This study investigated the conceptual pathways of 19 Grade 11 introductory chemistry students (age 16-17) as they participated in a multirepresentational instruction on the particulate nature of matter (PNM). This study was grounded in contemporary conceptual change theory, in particular, research on students' conceptual pathways that focuses on…

On Teaching About Terrorism: A Conceptual Approach.

ERIC Educational Resources Information Center

Kleg, Milton

1986-01-01

Recommends the use of conceptual mapping, case studies, and springboards to discussion and inquiry as viable approaches to the study of terrorism in secondary classrooms. Provides numerous examples of conceptual maps. (JDH)

Design and Optimization of a Hybrid-Driven Waist Rehabilitation Robot

PubMed Central

Zi, Bin; Yin, Guangcai; Zhang, Dan

2016-01-01

In this paper a waist rehabilitation robot driven by cables and pneumatic artificial muscles (PAMs) has been conceptualized and designed. In the process of mechanism design, the human body structure, the waist movement characteristics, and the actuators’ driving characteristics are the main considerable factors to make the hybrid-driven waist rehabilitation robot (HWRR) cost-effective, safe, flexible, and well-adapted. A variety of sensors are chosen to measure the position and orientation of the recovery patient to ensure patient safety at the same time as the structure design. According to the structure specialty and function, the HWRR is divided into two independent parallel robots: the waist twist device and the lower limb traction device. Then these two devices are analyzed and evaluated, respectively. Considering the characters of the human body in the HWRR, the inverse kinematics and statics are studied when the waist and the lower limb are considered as a spring and link, respectively. Based on the inverse kinematics and statics, the effect of the contraction parameter of the PAM is considered in the optimization of the waist twist device, and the lower limb traction device is optimized using particle swarm optimization (PSO) to minimize the global conditioning number over the feasible workspace. As a result of the optimization, an optimal rehabilitation robot design is obtained and the condition number of the Jacobian matrix over the feasible workspace is also calculated. PMID:27983626

Design and Optimization of a Hybrid-Driven Waist Rehabilitation Robot.

PubMed

Zi, Bin; Yin, Guangcai; Zhang, Dan

2016-12-14

In this paper a waist rehabilitation robot driven by cables and pneumatic artificial muscles (PAMs) has been conceptualized and designed. In the process of mechanism design, the human body structure, the waist movement characteristics, and the actuators' driving characteristics are the main considerable factors to make the hybrid-driven waist rehabilitation robot (HWRR) cost-effective, safe, flexible, and well-adapted. A variety of sensors are chosen to measure the position and orientation of the recovery patient to ensure patient safety at the same time as the structure design. According to the structure specialty and function, the HWRR is divided into two independent parallel robots: the waist twist device and the lower limb traction device. Then these two devices are analyzed and evaluated, respectively. Considering the characters of the human body in the HWRR, the inverse kinematics and statics are studied when the waist and the lower limb are considered as a spring and link, respectively. Based on the inverse kinematics and statics, the effect of the contraction parameter of the PAM is considered in the optimization of the waist twist device, and the lower limb traction device is optimized using particle swarm optimization (PSO) to minimize the global conditioning number over the feasible workspace. As a result of the optimization, an optimal rehabilitation robot design is obtained and the condition number of the Jacobian matrix over the feasible workspace is also calculated.

Constructing a new theory from old ideas and new evidence

PubMed Central

Rhodes, Marjorie; Wellman, Henry

2014-01-01

A central tenet of constructivist models of conceptual development is that children’s initial conceptual level constrains how they make sense of new evidence and thus whether exposure to evidence will prompt conceptual change. Yet, little experimental evidence directly examines this claim for the case of sustained, fundamental conceptual achievements. The present study combined scaling and experimental microgenetic methods to examine the processes underlying conceptual change in the context of an important conceptual achievement of early childhood—the development of a representational theory of mind. Results from 47 children (M age = 3.7 years) indicate that only children who were conceptually close to understanding false belief at the beginning of the study, and who were experimentally exposed to evidence of people acting on false beliefs, reliably developed representational theories of minds. Combined scaling and microgenetic data revealed how prior conceptual level interacts with experience, thereby providing critical experimental evidence for how conceptual change results from the interplay between conceptions and evidence. PMID:23489194

A Study of Novice Science Teachers' Conceptualizations of Culturally Relevant Pedagogy

NASA Astrophysics Data System (ADS)

Redman, Elizabeth Horst

This qualitative study examined new science teachers' conceptualization of culturally relevant pedagogy (CRP). The study followed six novice science teachers from their preservice teaching placements into their first jobs as instructors of record, observing in their classrooms and interviewing them about their use of CRP. The study sought to understand (1) how the participating teachers conceptualize CRP in science, and (2) what challenges the teachers faced in trying to implement CRP. Findings suggest that the teachers conceptualized CRP in ways that were consistent with Enyedy, Danish and Fields' (2011) interpretations of relevance: relevance of authentic purpose, relevance of content and/or context, and relevance of practices. The teachers, however, translated those interpretations of relevance into their conceptualizations and classroom practice in a variety of ways. While they encountered difficulties in conceptualizing and practicing CRP, they also made productive moves in their practice and evidenced positive elements in their conceptualizations of CRP. In order to address the challenges these teachers faced in implementing CRP, I suggest an approach to teacher preparation in CRP that builds upon the understandings and productive moves the teachers evidenced in this study.

Is a Transdisciplinary Theory of Engagement in Organized Settings Possible? A Concept Analysis of the Literature on Employee Engagement, Consumer Engagement and Patient Engagement.

PubMed

Graffigna, Guendalina

2017-01-01

Organizations are experiencing increased competition, disruptive innovation, and continuous changes in their social and economic context. Furthermore, the decrease of resources (economic and human) in such a demanding context make it imperative for organizations to find new models and strategies to make their service delivery more sustainable at the economic, environmental and psychological levels. In such a complex scenario the concept of engagement of the individuals involved in organized settings (either as service providers or as final receivers) is a promising lever for innovation. However, despite the number of studies on the matter, the debate on engagement is still very fragmented because the corpus of literature addressing the different areas of engagement is divided and diverse in its nature. In this paper, we discuss the results of a conceptual analysis of the literature conducted in order to investigate overlapping features and areas of divergence among three different areas of investigation and application of the engagement phenomenon in organized settings: the domains of employee engagement, consumer engagement, and patient engagement. These are deliberately selected as prototypical of the phenomenon of engagement along the "inside/outside" of organizational settings. The analysis consisted in a qualitative conceptual survey? Of the scholarly literature indexed with the key terms "employee engagement," "consumer engagement," and "patient engagement." We performed a key-word based survey? Of the literature in the Scopus database. A total of 163 articles were selected and analyzed. The analysis cast light on the following areas of conceptual overlap among employee, consumer and patient engagement: (1) engagement is different from empowerment and activation; (2) engagement is a multi-componential psychological experience; (3) engagement is a self-transformative experience; (4) engagement develops within a relational context; (5) engagement is a systemic phenomenon. These findings, although preliminary and in need of further investigation, suggest the feasibility of promoting a transdisciplinary reflection on the phenomenon of engagement in organized settings.

A feasibility assessment of magnetic bearings for free-piston Stirling space power converters

NASA Technical Reports Server (NTRS)

Curwen, Peter W.; Rao, Dantam K.; Wilson, Donald R.

1992-01-01

This report describes a design and analysis study performed by Mechanical Technology Incorporated (MTI) under NASA Contract NAS3-26061. The objective of the study was to assess the feasibility and efficacy of applying magnetic bearings to free-piston Stirling-cycle power conversion machinery of the type currently being evaluated for possible use in long-term space missions. The study was performed for a 50-kWe Reference Stirling Space Power Converter (RSSPC) system consisting of two 25-kWe free-piston Stirling engine modules. Two different versions of the RSSPC engine modules have been defined under NASA Contract NAS3-25463. These modules currently use hydrostatic gas bearings to support the reciprocating displacer and power piston assemblies. Results of this study show that active magnetic bearings of the attractive electromagnetic type are technically feasible for RSSPC application provided that wire insulation with 60,000-hr life capability at 300 C can be developed for the bearing coils. From a design integration standpoint, both versions of the RSSPC were found to be conceptually amenable to magnetic support of the power piston assembly. However, only one version of the RSSPC was found to be amendable to magnetic support of the displacer assembly. Unacceptable changes to the basic engine design would be required to incorporate magnetic displacer bearings into the second version. Complete magnetic suspension of the RSSPC can potentially increase overall efficiency of the Stirling cycle power converter by 0.53 to 1.4 percent (0.15 to 0.4 efficiency points). Magnetic bearings will also overcome several operational concerns associated with hydrostatic gas bearing systems. However, these advantages are accompanied by a 5 to 8 percent increase in specific mass of the RSSPC, depending on the RSSPC version employed. Additionally, magnetic bearings are much more complex, both mechanically and particularly electronically, than hydrostatic bearings. Accordingly, long-term stability and reliability represent areas of uncertainty for magnetic bearings. Considerable development effort will be required to establish the long-term suitability of these bearings for Stirling space power applications.

Integrated low emissions cleanup system for direct coal-fueled turbines

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lippert, T.E.; Newby, R.A.; Alvin, M.A.

1992-01-01

The Westinghouse Electric Corporation, Science Technology Center (W-STC) is developing an Integrated Low Emissions Cleanup (ILEC) concept for high-temperature gas cleaning to meet environmental standards, as well as to economical gas turbine life. The ILEC concept simultaneously controls sulfur, particulate, and alkali contaminants in high-pressure fuel gases or combustion gases at temperatures up to 1850[degrees]F for advanced power generation systems (PFBC, APFBC, IGCC, DCF7). The objective of this program is to demonstrate, at a bench scale, the conceptual, technical feasibility of the REC concept. The ELEC development program has a 3 phase structure: Phase 1 - laboratory-scale testing; phase 2more » - bench-scale equipment; design and fabrication; and phase 3 - bench-scale testing. Phase 1 laboratory testing has been completed. In Phase 1, entrained sulfur and alkali sorbent kinetics were measured and evaluated, and commercial-scale performance was projected. Related cold flow model testing has shown that gas-particle contacting within the ceramic barrier filter vessel will provide a good reactor environment. The Phase 1 test results and the commercial evaluation conducted in the Phase 1 program support the bench-scale facility testing to be performed in Phase 3. Phase 2 is nearing completion with the design and assembly of a modified, bench-scale test facility to demonstrate the technical feasibility of the ILEC features. This feasibility testing will be conducted in Phase 3.« less

Integrated low emissions cleanup system for direct coal-fueled turbines

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lippert, T.E.; Newby, R.A.; Alvin, M.A.

1992-12-31

The Westinghouse Electric Corporation, Science & Technology Center (W-STC) is developing an Integrated Low Emissions Cleanup (ILEC) concept for high-temperature gas cleaning to meet environmental standards, as well as to economical gas turbine life. The ILEC concept simultaneously controls sulfur, particulate, and alkali contaminants in high-pressure fuel gases or combustion gases at temperatures up to 1850{degrees}F for advanced power generation systems (PFBC, APFBC, IGCC, DCF7). The objective of this program is to demonstrate, at a bench scale, the conceptual, technical feasibility of the REC concept. The ELEC development program has a 3 phase structure: Phase 1 - laboratory-scale testing; phasemore » 2 - bench-scale equipment; design and fabrication; and phase 3 - bench-scale testing. Phase 1 laboratory testing has been completed. In Phase 1, entrained sulfur and alkali sorbent kinetics were measured and evaluated, and commercial-scale performance was projected. Related cold flow model testing has shown that gas-particle contacting within the ceramic barrier filter vessel will provide a good reactor environment. The Phase 1 test results and the commercial evaluation conducted in the Phase 1 program support the bench-scale facility testing to be performed in Phase 3. Phase 2 is nearing completion with the design and assembly of a modified, bench-scale test facility to demonstrate the technical feasibility of the ILEC features. This feasibility testing will be conducted in Phase 3.« less

Examining the influence of formative assessment on conceptual accumulation and conceptual change

NASA Astrophysics Data System (ADS)

Tomita, Miki K.

This study explored the effect of formative assessment on student achievement in science. Research in science education has shown that students enter science classrooms with previously formed explanatory models of the natural world; these naive "mental models" have a substantial influence on their learning of scientific conceptions. In general, conceptual change describes the pathway from pre-instructional or prior conceptions to a post-instructional or desired conception. Conceptual change involves a fundamental restructuring of a network of concepts rather than fitting new concepts into an existing conceptual network or structure. Research has shown that conceptual change is difficult to promote; for example, students may accumulate multiple conceptions over the course of instruction, including both new misconceptions and more scientifically-sound conceptions. Hellden and Solomon (2004) found that although students tended to evoke the same, less-scientific conceptions over time, they could produce more scientifically-sound conceptions during interviews with appropriate prompting; thus, students undergo conceptual accumulation rather than conceptual change. Students can recall scientifically-sound conceptions they have learned and may use them to reason, but they do so in partnership or hybridization with their less-scientific prior conceptions. Formative assessment, which focuses on providing immediate feedback by acting upon student understanding during the course of instruction, and conceptual change have both been linked to increased student achievement. Formative assessment is an instructional strategy that helps teachers to assess students' current understanding, identify the gap between current understanding and expected understanding, and provide immediate and useful feedback to students on how to close the gap. Formative assessment ranges from formal (e.g. embedded, planned-for interactions between teacher and entire class) to informal (e.g. on-the-fly interactions between teacher and class or student). In this study, the links between formative assessment and conceptual accumulation and conceptual change were explored. Specifically, this study asked: (1) Does formative assessment promote conceptual accumulation, and (2) Does formative assessment promote conceptual change? It was hypothesized that conceptual change-focused formative assessment would foster conceptual change, in addition to supporting conceptual accumulation. It was further hypothesized that all students will show gains in conceptual accumulation as indicated by measures of declarative and procedural knowledge, but that students exposed to conceptual change-focused formative assessment would also show gains in conceptual change as indicated by measures of schematic knowledge or mental models. To research the effect of formative assessment on conceptual accumulation and conceptual change, a small randomized experiment involving 102 middle school students was conducted. In Phase I of the study, 52 6th graders were randomly assigned to a treatment or control group; in Phase II of this study, 50 7th graders were randomly assigned to a treatment or control group. Both the control and experimental groups in both phases were taught about sinking and floating by the same teacher (the author) with identical curriculum materials and activities. In addition, the experimental group received three sets of embedded formative assessments focused on conceptual change around the topic of why things sink and float during the course of instruction. In Phase I of this study, both groups were kept at the same pace through the entire sequence of investigations. The control condition spent more time on some of the more critical FAST lessons, gathering additional data to support the theories the curriculum expected they would develop at a particular juncture but not receiving structured experiences aimed at addressing misconceptions. In Phase II, students in the control condition spent roughly the same time on each FAST lesson as those in the experimental condition (e.g. they finished the sequence of activities earlier because they did not have class sessions devoted to the RLs inserted at critical junctures) but participated in the formal assessments as a block of activities after they finished the FAST investigations and posttest measures. In other words, in addition to replicating Phase I, Phase II included a Reflective Lesson section for the control group after the end of the experiment proper, followed by a post-posttest. Overall, it was found that embedding conceptual change-focused formative assessments in the FAST curriculum significantly influenced conceptual change. It was also found that all students experienced significant gains in terms of their conceptual accumulation, regardless of exposure to the formative assessments. This study connected two previously isolated but theoretically linked educational frameworks: conceptual change and formative assessment. It was found that formative assessments can be used to promote conceptual change. It was also found that conceptual change is different than conceptual accumulation, in that students who show gains on measures of declarative and procedural knowledge do not necessarily show gains on measures of schematic knowledge. (Abstract shortened by UMI.)

Autonomous and Autonomic Systems: A Paradigm for Future Space Exploration Missions

NASA Technical Reports Server (NTRS)

Truszkowski, Walter F.; Hinchey, Michael G.; Rash, James L.; Rouff, Christopher A.

2004-01-01

NASA increasingly will rely on autonomous systems concepts, not only in the mission control centers on the ground, but also on spacecraft and on rovers and other assets on extraterrestrial bodies. Automomy enables not only reduced operations costs, But also adaptable goal-driven functionality of mission systems. Space missions lacking autonomy will be unable to achieve the full range of advanced mission objectives, given that human control under dynamic environmental conditions will not be feasible due, in part, to the unavoidably high signal propagation latency and constrained data rates of mission communications links. While autonomy cost-effectively supports accomplishment of mission goals, autonomicity supports survivability of remote mission assets, especially when human tending is not feasible. Autonomic system properties (which ensure self-configuring, self-optimizing self-healing, and self-protecting behavior) conceptually may enable space missions of a higher order into any previously flown. Analysis of two NASA agent-based systems previously prototyped, and of a proposed future mission involving numerous cooperating spacecraft, illustrates how autonomous and autonomic system concepts may be brought to bear on future space missions.

IPMC-driven thrust generation: a new conceptual design (Conference Presentation)

NASA Astrophysics Data System (ADS)

Olsen, Zakai; Kim, Kwang Jin

2017-04-01

Ionic Polymer-Metal Composites (IPMC) are highly functional actuators that find many uses in the field of soft robotics due to their low actuation voltage and ability to operate in aquatic environments. The actuation of an IPMC relies on the swelling of the negatively charged side when a potential is applied, due to the free-moving cations and water molecules migrating to that half. While this bending type actuation can be utilized to perform many tasks, it is ill suited for the primary propulsion mechanism in certain soft robotic applications. Here, a new conceptual design is presented which utilizes the bending of IPMC materials to achieve complex actuation motion in an attempt to generate a non-zero net thrust for propulsion of soft robots. The design capitalizes on advances in the manufacturing processes of electroactive polymer materials, which now allow for more complex shapes and thus new and unique modes of actuation. By utilizing the consistent bending deformation of IPMC actuators, in conjunction with carefully considered geometry, an IPMC driven body may serve as a primary mode of propulsion through a positive net thrust generation. This work consists of the initial feasibility study, concept testing, and optimization for such an actuator through computer modeling and simulation. COMSOL will be used for the finite element analysis to design the most efficient and optimized design for a positive net thrust generation. Such an IPMC design may find a great deal of applications, and the potential of future integration into other soft robotic systems is considered.

A Standardized, Evidence-Based Massage Therapy Program for Decentralized Elite Paracyclists: Creating the Model.

PubMed

Kennedy, Ann B; Trilk, Jennifer L

2015-09-01

Evidence suggests that para-athletes are injured more often than able-bodied athletes. The benefits of massage therapy for these disabled athletes are yet to be explored. This paper documents the process followed for creating a massage program for elite paracycling athletes with the goal to assess effects on recovery, rest, performance, and quality of life both on and off the bike. Massage therapists' private practices throughout the United States. A United States Paracycling team consisting of 9 elite athletes: 2 spinal cord injury, 2 lower limb amputation, 1 upper limb amputation, 1 transverse myelitis, 1 stroke, 1 traumatic brain injury, and 1 visually impaired. The process used to develop a massage therapy program for para-cyclists included meetings with athletes, coaching staff, team exercise physiologist, and sports massage therapists; peer-reviewed literature was also consulted to address specific health conditions of para-athletes. Team leadership and athletes identified needs for quicker recovery, better rest, and improved performance in elite paracyclists. This information was used to generate a conceptual model for massage protocols, and led to creation of the intake and exit questionnaires to assess patient health status and recovery. Forms also were created for a general health intake, therapist information, and a therapist's SOAAP notes. The conceptual model and questionnaires developed herein will help to operationalize an exploratory study investigating the feasibility of implementing a standardized massage therapy program for a decentralized elite paracycling team.

Conceptual Design for a Dual-Bell Rocket Nozzle System Using a NASA F-15 Airplane as the Flight Testbed

NASA Technical Reports Server (NTRS)

Jones, Daniel S.; Ruf, Joseph H.; Bui, Trong T.; Martinez, Martel; St. John, Clinton W.

2014-01-01

The dual-bell rocket nozzle was first proposed in 1949, offering a potential improvement in rocket nozzle performance over the conventional-bell nozzle. Despite the performance advantages that have been predicted, both analytically and through static test data, the dual-bell nozzle has still not been adequately tested in a relevant flight environment. In 2013 a proposal was constructed that offered a NASA F-15 airplane as the flight testbed, with the plan to operate a dual-bell rocket nozzle during captive-carried flight. If implemented, this capability will permit nozzle operation into an external flow field similar to that of a launch vehicle, and facilitate an improved understanding of dual-bell nozzle plume sensitivity to external flow-field effects. More importantly, this flight testbed can be utilized to help quantify the performance benefit with the dual-bell nozzle, as well as to advance its technology readiness level. This presentation provides highlights of a technical paper that outlines this ultimate goal, including plans for future flights to quantify the external flow field of the airplane near the nozzle experiment, as well as details on the conceptual design for the dual-bell nozzle cold-flow propellant feed system integration within the NASA F-15 Propulsion Flight Test Fixture. The current study shows that this concept of flight research is feasible, and could result in valuable flight data for the dual-bell nozzle.

Conceptual Design for a Dual-Bell Rocket Nozzle System Using a NASA F-15 Airplane as the Flight Testbed

NASA Technical Reports Server (NTRS)

Jones, Daniel S.; Ruf, Joseph H.; Bui, Trong T.; Martinez, Martel; St. John, Clinton W.

2014-01-01

The dual-bell rocket nozzle was first proposed in 1949, offering a potential improvement in rocket nozzle performance over the conventional-bell nozzle. Despite the performance advantages that have been predicted, both analytically and through static test data, the dual-bell nozzle has still not been adequately tested in a relevant flight environment. In 2013 a proposal was constructed that offered a National Aeronautics and Space Administration (NASA) F-15 airplane as the flight testbed, with the plan to operate a dual-bell rocket nozzle during captive-carried flight. If implemented, this capability will permit nozzle operation into an external flow field similar to that of a launch vehicle, and facilitate an improved understanding of dual-bell nozzle plume sensitivity to external flow-field effects. More importantly, this flight testbed can be utilized to help quantify the performance benefit with the dual-bell nozzle, as well as to advance its technology readiness level. Toward this ultimate goal, this report provides plans for future flights to quantify the external flow field of the airplane near the nozzle experiment, as well as details on the conceptual design for the dual-bell nozzle cold-flow propellant feed system integration within the NASA F-15 Propulsion Flight Test Fixture. The current study shows that this concept of flight research is feasible, and could result in valuable flight data for the dual-bell nozzle.

Conceptual design of a 10 to the 8th power bit magnetic bubble domain mass storage unit and fabrication, test and delivery of a feasibility model

NASA Technical Reports Server (NTRS)

1972-01-01

The conceptual design of a highly reliable 10 to the 8th power-bit bubble domain memory for the space program is described. The memory has random access to blocks of closed-loop shift registers, and utilizes self-contained bubble domain chips with on-chip decoding. Trade-off studies show that the highest reliability and lowest power dissipation is obtained when the memory is organized on a bit-per-chip basis. The final design has 800 bits/register, 128 registers/chip, 16 chips/plane, and 112 planes, of which only seven are activated at a time. A word has 64 data bits +32 checkbits, used in a 16-adjacent code to provide correction of any combination of errors in one plane. 100 KHz maximum rotational frequency keeps power low (equal to or less than, 25 watts) and also allows asynchronous operation. Data rate is 6.4 megabits/sec, access time is 200 msec to an 800-word block and an additional 4 msec (average) to a word. The fabrication and operation are also described for a 64-bit bubble domain memory chip designed to test the concept of on-chip magnetic decoding. Access to one of the chip's four shift registers for the read, write, and clear functions is by means of bubble domain decoders utilizing the interaction between a conductor line and a bubble.

Effects of `Environmental Chemistry' Elective Course Via Technology-Embedded Scientific Inquiry Model on Some Variables

NASA Astrophysics Data System (ADS)

Çalik, Muammer; Özsevgeç, Tuncay; Ebenezer, Jazlin; Artun, Hüseyin; Küçük, Zeynel

2014-06-01

The purpose of this study is to examine the effects of `environmental chemistry' elective course via Technology-Embedded Scientific Inquiry (TESI) model on senior science student teachers' (SSSTs) conceptions of environmental chemistry concepts/issues, attitudes toward chemistry, and technological pedagogical content knowledge (TPACK) levels. Within one group pre-test-post-test design, the study was conducted with 117 SSSTs (68 females and 49 males—aged 21-23 years) enrolled in an `environmental chemistry' elective course in the spring semester of 2011-2012 academic-years. Instruments for data collection comprised of Environmental Chemistry Conceptual Understanding Questionnaire, TPACK survey, and Chemistry Attitudes and Experiences Questionnaire. Significant increases in the SSSTs' conceptions of environmental chemistry concepts/issues, attitudes toward chemistry, and TPACK levels are attributed to the SSSTs learning how to use the innovative technologies in the contexts of the `environmental chemistry' elective course and teaching practicum. The study implies that the TESI model may serve a useful purpose in experimental science courses that use the innovative technologies. However, to generalize feasibility of the TESI model, it should be evaluated with SSSTs in diverse learning contexts.

Revealing Conceptual Understanding of International Business

ERIC Educational Resources Information Center

Ashley, Sue; Schaap, Harmen; de Bruijn, Elly

2017-01-01

This study aims to identify an adequate approach for revealing conceptual understanding in higher professional education. Revealing students' conceptual understanding is an important step towards developing effective curricula, assessment and aligned teaching strategies to enhance conceptual understanding in higher education. Essays and concept…

The Role of Cognitive, Metacognitive, and Motivational Variables in Conceptual Change: Preservice Early Childhood Teachers' Conceptual Understanding of the Cause of Lunar Phases

ERIC Educational Resources Information Center

Sackes, Mesut

2010-01-01

This study seeks to explore and describe the role of cognitive, metacognitive, and motivational variables in conceptual change. More specifically, the purposes of the study were (1) to investigate the predictive ability of a learning model that was developed based on the intentional conceptual change perspective in predicting change in conceptual…

Conceptualization of Depth of Vocabulary Knowledge with Academic Reading Comprehension

ERIC Educational Resources Information Center

Hasan, Md. Kamrul; Shabdin, Ahmad Affendi

2016-01-01

The present study embodies a conceptual framework, and it studies the concept regarding the depth of vocabulary knowledge. Literature review is employed as a foundation for developing the conceptual framework for the present study. The current study suggests that different dimensions of depth of vocabulary knowledge, namely paradigmatic relations,…

A Multivariate Model of Conceptual Change

ERIC Educational Resources Information Center

Taasoobshirazi, Gita; Heddy, Benjamin; Bailey, MarLynn; Farley, John

2016-01-01

The present study used the Cognitive Reconstruction of Knowledge Model (CRKM) model of conceptual change as a framework for developing and testing how key cognitive, motivational, and emotional variables are linked to conceptual change in physics. This study extends an earlier study developed by Taasoobshirazi and Sinatra ("J Res Sci…

Telephone Counselors' Conceptualising Abilities and Counseling Skills.

ERIC Educational Resources Information Center

McLennan, Jim; And Others

1994-01-01

Describes two studies examining the link between the counseling skills of hotline counselors and their conceptualizing abilities. The first relied on counselors' postinterview conceptualizations of callers' problems and found no link between conceptualization accuracy and counseling skill. However, the accuracy of conceptualizations as measured by…

Effect of perceptual load on conceptual processing: an extension of Vermeulen's theory.

PubMed

Xie, Jiushu; Wang, Ruiming; Sun, Xun; Chang, Song

2013-10-01

The effect of color and shape load on conceptual processing was studied. Perceptual load effects have been found in visual and auditory conceptual processing, supporting the theory of embodied cognition. However, whether different types of visual concepts, such as color and shape, share the same perceptual load effects is unknown. In the current experiment, 32 participants were administered simultaneous perceptual and conceptual tasks to assess the relation between perceptual load and conceptual processing. Keeping color load in mind obstructed color conceptual processing. Hence, perceptual processing and conceptual load shared the same resources, suggesting embodied cognition. Color conceptual processing was not affected by shape pictures, indicating that different types of properties within vision were separate.

Unconscious automatic brain activation of acoustic and action-related conceptual features during masked repetition priming.

PubMed

Trumpp, Natalie M; Traub, Felix; Pulvermüller, Friedemann; Kiefer, Markus

2014-02-01

Classical theories of semantic memory assume that concepts are represented in a unitary amodal memory system. In challenging this classical view, pure or hybrid modality-specific theories propose that conceptual representations are grounded in the sensory-motor brain areas, which typically process sensory and action-related information. Although neuroimaging studies provided evidence for a functional-anatomical link between conceptual processing of sensory or action-related features and the sensory-motor brain systems, it has been argued that aspects of such sensory-motor activation may not directly reflect conceptual processing but rather strategic imagery or postconceptual elaboration. In the present ERP study, we investigated masked effects of acoustic and action-related conceptual features to probe unconscious automatic conceptual processing in isolation. Subliminal feature-specific ERP effects at frontocentral electrodes were observed, which differed with regard to polarity, topography, and underlying brain electrical sources in congruency with earlier findings under conscious viewing conditions. These findings suggest that conceptual acoustic and action representations can also be unconsciously accessed, thereby excluding any postconceptual strategic processes. This study therefore further substantiates a grounding of conceptual and semantic processing in action and perception.

A unified approach for composite cost reporting and prediction in the ACT program

NASA Technical Reports Server (NTRS)

Freeman, W. Tom; Vosteen, Louis F.; Siddiqi, Shahid

1991-01-01

The Structures Technology Program Office (STPO) at NASA Langley Research Center has held two workshops with representatives from the commercial airframe companies to establish a plan for development of a standard cost reporting format and a cost prediction tool for conceptual and preliminary designers. This paper reviews the findings of the workshop representatives with a plan for implementation of their recommendations. The recommendations of the cost tracking and reporting committee will be implemented by reinstituting the collection of composite part fabrication data in a format similar to the DoD/NASA Structural Composites Fabrication Guide. The process of data collection will be automated by taking advantage of current technology with user friendly computer interfaces and electronic data transmission. Development of a conceptual and preliminary designers' cost prediction model will be initiated. The model will provide a technically sound method for evaluating the relative cost of different composite structural designs, fabrication processes, and assembly methods that can be compared to equivalent metallic parts or assemblies. The feasibility of developing cost prediction software in a modular form for interfacing with state of the art preliminary design tools and computer aided design (CAD) programs is assessed.

Technology-Based Early Warning Systems for Bipolar Disorder: A Conceptual Framework

PubMed Central

Torous, John; Thompson, Wesley

2016-01-01

Recognition and timely action around “warning signs” of illness exacerbation is central to the self-management of bipolar disorder. Due to its heterogeneity and fluctuating course, passive and active mobile technologies have been increasingly evaluated as adjunctive or standalone tools to predict and prevent risk of worsening of course in bipolar disorder. As predictive analytics approaches to big data from mobile health (mHealth) applications and ancillary sensors advance, it is likely that early warning systems will increasingly become available to patients. Such systems could reduce the amount of time spent experiencing symptoms and diminish the immense disability experienced by people with bipolar disorder. However, in addition to the challenges in validating such systems, we argue that early warning systems may not be without harms. Probabilistic warnings may be delivered to individuals who may not be able to interpret the warning, have limited information about what behaviors to change, or are unprepared to or cannot feasibly act due to time or logistic constraints. We propose five essential elements for early warning systems and provide a conceptual framework for designing, incorporating stakeholder input, and validating early warning systems for bipolar disorder with a focus on pragmatic considerations. PMID:27604265

Conceptual design of a high-speed electromagnetic switch for a modified flux-coupling-type SFCL and its application in renewable energy system.

PubMed

Chen, Lei; Chen, Hongkun; Yang, Jun; Shu, Zhengyu; He, Huiwen; Shu, Xin

2016-01-01

The modified flux-coupling-type superconducting fault current (SFCL) is a high-efficient electrical auxiliary device, whose basic function is to suppress the short-circuit current by controlling the magnetic path through a high-speed switch. In this paper, the high-speed switch is based on electromagnetic repulsion mechanism, and its conceptual design is carried out to promote the application of the modified SFCL. Regarding that the switch which is consisting of a mobile copper disc, two fixed opening and closing coils, the computational method for the electromagnetic force is discussed, and also the dynamic mathematical model including circuit equation, magnetic field equation as well as mechanical motion equation is theoretically deduced. According to the mathematical modeling and calculation of characteristic parameters, a feasible design scheme is presented, and the high-speed switch's response time can be less than 0.5 ms. For that the modified SFCL is equipped with this high-speed switch, the SFCL's application in a 10 kV micro-grid system with multiple renewable energy sources are assessed in the MATLAB software. The simulations are well able to affirm the SFCL's performance behaviors.

DOE Office of Scientific and Technical Information (OSTI.GOV)

O'Neil, D.J.; Colcord, A.R.; Bery, M.K.

The objective of this project is to design, fabricate, and operate a fermentation facility which will demonstrate on a pilot-scale level (3 oven-dry tons (ODT) per day of feedstock) the economic and technical feasibility of producing anhydrous ethyl alcohol from lignocellulosic biomass residues (wood, corn stover, and wheat straw principally). The resultant process development unit (PDU) will be flexibly designed so as to evaluate current and projected unit operations, materials of construction, chemical and enzymatic systems which offer the potential of significant technological and economic breakthroughs in alcohol production from biomass. The principal focus of the project is to generatemore » fuels from biomass. As such, in addition to alcohol which can be used as a transportation fuel, by-products are to be directed where possible to fuel applications. The project consists of two parts: (1) conceptual design, and (2) detailed engineering design. The first quarter's activities have focused on a critical review of several aspects of the conceptual design of the 3 ODT/day PDU, viz.: (1) biomass cost, availability, and characterization; (2) pretreatment processes for lignocellulosic residues; (3) hydrolytic processes (enzymatic and acidic); (4) fermentation processes; (5) alcohol recovery systems; (6) by-product streams utilization; and (7) process economics.« less

Development of High Fidelity, Fuel-Like Thermal Simulators for Non-Nuclear Testing

NASA Technical Reports Server (NTRS)

Bragg-Sitton, S. M.; Farmer, J.; Dixon, D.; Kapernick, R.; Dickens, R.; Adams, M.

2007-01-01

Non-nuclear testing can be a valuable tool in development of a space nuclear power or propulsion system. In a non-nuclear test bed, electric heaters are used to simulate the heat from nuclear fuel. Work at the NASA Marshall Space Flight Center seeks to develop high fidelity thermal simulators that not only match the static power profile that would be observed in an operating, fueled nuclear reactor, but to also match the dynamic fuel pin performance during feasible transients. Comparison between the fuel pins and thermal simulators is made at the fuel clad surface, which corresponds to the sheath surface in the thermal simulator. Static and dynamic fuel pin performance was determined using SINDA-FLUINT analysis, and the performance of conceptual thermal simulator designs was compared to the expected nuclear performance. Through a series of iterative analysis, a conceptual high fidelity design will be developed, followed by engineering design, fabrication, and testing to validate the overall design process. Although the resulting thermal simulator will be designed for a specific reactor concept, establishing this rigorous design process will assist in streamlining the thermal simulator development for other reactor concepts.

Conceptual Masking: How One Picture Captures Attention from Another Picture.

ERIC Educational Resources Information Center

Loftus, Geoffrey R.; And Others

1988-01-01

Five experiments studied operations of conceptual masking--the reduction of conceptual memory performance for an initial stimulus when it is followed by a masking picture process. The subjects were 337 undergraduates at the University of Washington (Seattle). Conceptual masking is distinguished from perceptual masking. (TJH)

Cultural adaptation of a pediatric functional assessment for rehabilitation outcomes research.

PubMed

Arestad, Kristen E; MacPhee, David; Lim, Chun Y; Khetani, Mary A

2017-09-15

Significant racial and ethnic health care disparities experienced by Hispanic children with special health care needs (CSHCN) create barriers to enacting culturally competent rehabilitation services. One way to minimize the impact of disparities in rehabilitation is to equip practitioners with culturally relevant functional assessments to accurately determine service needs. Current approaches to culturally adapting assessments have three major limitations: use of inconsistent translation processes; current processes assess for some, but not all, elements of cultural equivalence; and limited evidence to guide decision making about whether to undertake cultural adaptation with and without language translation. The aims of this observational study are (a) to examine similarities and differences of culturally adapting a pediatric functional assessment with and without language translation, and (b) to examine the feasibility of cultural adaptation processes. The Young Children's Participation and Environment Measure (YC-PEM), a pediatric functional assessment, underwent cultural adaptation (i.e., language translation and cognitive testing) to establish Spanish and English pilot versions for use by caregivers of young CSHCN of Mexican descent. Following language translation to develop a Spanish YC-PEM pilot version, 7 caregivers (4 Spanish-speaking; 3 English-speaking) completed cognitive testing to inform decisions regarding content revisions to English and Spanish YC-PEM versions. Participant responses were content coded to established cultural equivalencies. Coded data were summed to draw comparisons on the number of revisions needed to achieve cultural equivalence between the two versions. Feasibility was assessed according to process data and data quality. Results suggest more revisions are required to achieve cultural equivalence for the translated (Spanish) version of the YC-PEM. However, issues around how the participation outcome is conceptualized were identified in both versions. Feasibility results indicate that language translation processes require high resource investment, but may increase translation quality. However, use of questionnaires versus interview methods for cognitive testing may have limited data saturation. Results lend preliminary support to the need for and feasibility of cultural adaptation with and without language translation. Results inform decisions surrounding cultural adaptations with and without language translation and thereby enhance cultural competence and quality assessment of healthcare need within pediatric rehabilitation.

Utility of a Conceptual Framework within Doctoral Study: A Researcher's Reflections

ERIC Educational Resources Information Center

Berman, Jeanette

2013-01-01

The author of this paper provides an example of a conceptual framework that supported her doctoral study and written dissertation in the field of educational psychology. The study was carried out prior to the more recent explicit emphasis on conceptual frameworks in postgraduate research texts and academic literature. The instigation for the…

Conceptual Change and Physics Instruction: A Longitudinal Study.

ERIC Educational Resources Information Center

Searle, Peter; Gunstone, Richard F.

This paper reports an action study of conceptual change in mechanics using an instructional strategy based on a constructivist view of learning. The aims of the study were to determine: (1) what effect the instructional strategy had on achieving conceptual change; (2) what devices or strategies students used in their attempts to understand…

Attitudes of eighth-grade honors students toward the conceptual change methods of teaching science

NASA Astrophysics Data System (ADS)

Heide, Clifford Lee

1998-12-01

The study researched the attitude of eighth grade honors science students toward the steps of the conceptual change teaching method. The attitudes of 25 students in an honors 8th grade science class in the Greater Phoenix metropolitan area were assessed using a multi-method approach. A quantitative method (student survey) and a qualitative method (focus group) were triangulated for convergence. Since conceptual change is a relatively new reform teaching modality, the study assessed students' attitudes utilizing this method. Conceptual change teaching is characterized by connections between concepts and facts which are organized around key ideas. Knowledge connected through concepts is constantly revised and edited by students as they continue to learn and add new concepts. The results of this study produced evidence that the conceptual change method of teaching science and its six process steps have qualities that foster positive student attitude. The study demonstrated that students' attitudes toward science is positively influenced through the conceptual change teaching method by enabling students to: (1) choose problems and find solutions to those problems (student directed); (2) work together in large and small groups; (3) learn through student oral presentations; (4) perform hands-on laboratory experiences; (5) learn through conceptual understanding not memorization; (6) implement higher order learning skills to make connections from the lab to the real world. Teachers can use the information in the study to become aware of the positive and negative attitudes of students taught with the conceptual change method. Even if the conceptual change teaching strategy is not the modality utilized by an educator, the factors identified by this study that affect student attitude could be used to help a teacher design lesson plans that help foster positive student attitudes.

Inviscid/Boundary-Layer Aeroheating Approach for Integrated Vehicle Design

NASA Technical Reports Server (NTRS)

Lee, Esther; Wurster, Kathryn E.

2017-01-01

A typical entry vehicle design depends on the synthesis of many essential subsystems, including thermal protection system (TPS), structures, payload, avionics, and propulsion, among others. The ability to incorporate aerothermodynamic considerations and TPS design into the early design phase is crucial, as both are closely coupled to the vehicle's aerodynamics, shape and mass. In the preliminary design stage, reasonably accurate results with rapid turn-representative entry envelope was explored. Initial results suggest that for Mach numbers ranging from 9-20, a few inviscid solutions could reasonably sup- port surface heating predictions at Mach numbers variation of +/-2, altitudes variation of +/-10 to 20 kft, and angle-of-attack variation of +/- 5. Agreement with Navier-Stokes solutions was generally found to be within 10-15% for Mach number and altitude, and 20% for angle of attack. A smaller angle-of-attack increment than the 5 deg around times for parametric studies and quickly evolving configurations are necessary to steer design decisions. This investigation considers the use of an unstructured 3D inviscid code in conjunction with an integral boundary-layer method; the former providing the flow field solution and the latter the surface heating. Sensitivity studies for Mach number, angle of attack, and altitude, examine the feasibility of using this approach to populate a representative entry flight envelope based on a limited set of inviscid solutions. Each inviscid solution is used to generate surface heating over the nearby trajectory space. A subset of a considered in this study is recommended. Results of the angle-of-attack sensitivity studies show that smaller increments may be needed for better heating predictions. The approach is well suited for application to conceptual multidisciplinary design and analysis studies where transient aeroheating environments are critical for vehicle TPS and thermal design. Concurrent prediction of aeroheating environments, coupled with the use of unstructured methods, is considered enabling for TPS material selection and design in conceptual studies where vehicle mission, shape, and entry strategies evolve rapidly.

Conceptual and perceptual encoding instructions differently affect event recall.

PubMed

García-Bajos, Elvira; Migueles, Malen; Aizpurua, Alaitz

2014-11-01

When recalling an event, people usually retrieve the main facts and a reduced proportion of specific details. The objective of this experiment was to study the effects of conceptually and perceptually driven encoding in the recall of conceptual and perceptual information of an event. The materials selected for the experiment were two movie trailers. To enhance the encoding instructions, after watching the first trailer participants answered conceptual or perceptual questions about the event, while a control group answered general knowledge questions. After watching the second trailer, all of the participants completed a closed-ended recall task consisting of conceptual and perceptual items. Conceptual information was better recalled than perceptual details and participants made more perceptual than conceptual commission errors. Conceptually driven processing enhanced the recall of conceptual information, while perceptually driven processing not only did not improve the recall of descriptive details, but also damaged the standard conceptual/perceptual recall relationship.

Monitoring of Earth Rotation by VLBI

NASA Technical Reports Server (NTRS)

Ma., Chopo; Macmillan, D. S.

2000-01-01

Monitoring Earth rotation with Very Long Baseline Interferometry (VLBI) has unique potential because of direct access to the Celestial Reference System (CRF and Terrestrial Reference System (TRF) and the feasibility of re-analyzing the entire data set. While formal precision of better than 0.045 mas for pole and 0.002 ms for UT 1 has been seen in the best 24-hr data, the accuracy of the Earth Orientation Parameter (EOP) time series as a whole is subject to logistical, operational, analytical and conceptual constraints. The current issues related to the VLBI data set and the CORE program for greater time resolution such as analysis consistency, network jitter and reference frame stability will be discussed.

JT8D and JT9D jet engine performance improvement program. Task 1: Feasibility analysis

NASA Technical Reports Server (NTRS)

Gaffin, W. O.; Webb, D. E.

1979-01-01

JT8D and JT9D component performance improvement concepts which have a high probability of incorporation into production engines were identified and ranked. An evaluation method based on airline payback period was developed for the purpose of identifying the most promising concepts. The method used available test data and analytical models along with conceptual/preliminary designs to predict the performance improvements, weight, installation characteristics, cost for new production and retrofit, maintenance cost, and qualitative characteristics of candidate concepts. These results were used to arrive at the concept payback period, which is the time required for an airline to recover the investment cost of concept implementation.

Local Multi-Channel RF Surface Coil versus Body RF Coil Transmission for Cardiac Magnetic Resonance at 3 Tesla: Which Configuration Is Winning the Game?

PubMed

Weinberger, Oliver; Winter, Lukas; Dieringer, Matthias A; Els, Antje; Oezerdem, Celal; Rieger, Jan; Kuehne, Andre; Cassara, Antonino M; Pfeiffer, Harald; Wetterling, Friedrich; Niendorf, Thoralf

2016-01-01

The purpose of this study was to demonstrate the feasibility and efficiency of cardiac MR at 3 Tesla using local four-channel RF coil transmission and benchmark it against large volume body RF coil excitation. Electromagnetic field simulations are conducted to detail RF power deposition, transmission field uniformity and efficiency for local and body RF coil transmission. For both excitation regimes transmission field maps are acquired in a human torso phantom. For each transmission regime flip angle distributions and blood-myocardium contrast are examined in a volunteer study of 12 subjects. The feasibility of the local transceiver RF coil array for cardiac chamber quantification at 3 Tesla is demonstrated. Our simulations and experiments demonstrate that cardiac MR at 3 Tesla using four-channel surface RF coil transmission is competitive versus current clinical CMR practice of large volume body RF coil transmission. The efficiency advantage of the 4TX/4RX setup facilitates shorter repetition times governed by local SAR limits versus body RF coil transmission at whole-body SAR limit. No statistically significant difference was found for cardiac chamber quantification derived with body RF coil versus four-channel surface RF coil transmission. Our simulation also show that the body RF coil exceeds local SAR limits by a factor of ~2 when driven at maximum applicable input power to reach the whole-body SAR limit. Pursuing local surface RF coil arrays for transmission in cardiac MR is a conceptually appealing alternative to body RF coil transmission, especially for patients with implants.

Asteroid Return Mission Feasibility Study

NASA Technical Reports Server (NTRS)

Brophy, John R.; Gershman, Robert; Landau, Damon; Polk, James; Porter, Chris; Yeomans, Don; Allen, Carlton; Williams, Willie; Asphaug, Erik

2011-01-01

This paper describes an investigation into the technological feasibility of finding, characterizing, robotically capturing, and returning an entire Near-Earth Asteroid (NEA) to the International Space Station (ISS) for scientific investigation, evaluation of its resource potential, determination of its internal structure and other aspects important for planetary defense activities, and to serve as a testbed for human operations in the vicinity of an asteroid. Reasonable projections suggest that several dozen candidates NEAs in the size range of interest (approximately 2-m diameter) will be known before the end of the decade from which a suitable target could be selected. The conceptual mission objective is to return an approximately 10,000-kg asteroid to the ISS in a total flight time of approximately 5 years using a single Evolved Expendable Launch Vehicle. Preliminary calculations indicate that this could be accomplished using a solar electric propulsion (SEP) system with high-power Hall thrusters and a maximum power into the propulsion system of approximately 40 kW. The SEP system would be used to provide all of the post-launch delta V. The asteroid would have an unrestricted Earth return Planetary Protection categorization, and would be curated at the ISS where numerous scientific and resource utilization experiments would be conducted. Asteroid material brought to the ground would be curated at the NASA Johnson Space Center. This preliminary study identified several areas where additional work is required, but no show stoppers were identified for the approach that would return an entire 10,000-kg asteroid to the ISS in a mission that could be launched by the end of this decade.

Learner factors associated with radical conceptual change among undergraduates

NASA Astrophysics Data System (ADS)

Olson, Joanne Kay

Students frequently enter learning situations with knowledge inconsistent with scientific views. One goal of science instruction is to enable students to construct scientifically accepted ideas while rejecting inaccurate constructs. This process is called conceptual change. This study examined factors associated with students at three levels of conceptual change to elucidate possible influences on the conceptual change process. Factors studied included motivation (including utility value, interest, attainment value, mood, self efficacy, and task difficulty), prior experiences with science, perceptions of the nature of science, connections to objects or events outside the classroom, and specific activities that helped students learn. Four science classes for undergraduate preservice elementary teachers participated in the study, conducted during a three week unit on electricity. Data sources included concept maps, drawings, reflective journal entries, quizzes, a science autobiography assignment, and interviews. Concept maps, drawings, and quizzes were analyzed, and students were placed into high, moderate, and low conceptual change groups. Of the ninety-eight students in the study, fifty-seven were interviewed. Perhaps the most important finding of this study relates to the assessment of conceptual change. Interviews were conducted two months after the unit, and many items on the concept maps had decayed from students' memories. This indicates that time is an important factor. In addition, interview-derived data demonstrated conceptual change levels; concept maps were insufficient to indicate the depth of students' understanding. Factors associated with conceptual change include self efficacy and interest in topic. In addition, moderate conceptual change students cited specific activities as having helped them learn. Low and high students focused on the method of instruction rather than specific activities. Factors not found to be associated with conceptual change include: utility value, mood, task difficulty, and prior experiences with science, and connections to objects and events outside the classroom. Attainment value, perceptions of the nature of science, and mood cannot be ruled out as possible factors due to the problematic nature of assessing them within the context of this study.

Calculus Students' and Instructors' Conceptualizations of Slope: A Comparison across Academic Levels

ERIC Educational Resources Information Center

Nagle, Courtney; Moore-Russo, Deborah; Viglietti, Janine; Martin, Kristi

2013-01-01

This study considers tertiary calculus students' and instructors' conceptualizations of slope. Qualitative techniques were employed to classify responses to 5 items using conceptualizations of slope identified across various research settings. Students' responses suggest that they rely on procedurally based conceptualizations of…

Deconstructing Masculinity: A Qualitative Study of College Men's Masculine Conceptualizations and Gender Performance

ERIC Educational Resources Information Center

Harris, Frank, III

2008-01-01

Informed by the constructionist epistemological perspective, the purpose of this study was to examine socially constructed conceptualizations of masculinity and gender performance among 12 culturally diverse undergraduate men. The participants espoused seemingly productive conceptualizations of masculinity, yet their gendered behaviors were…

Using whole disease modeling to inform resource allocation decisions: economic evaluation of a clinical guideline for colorectal cancer using a single model.

PubMed

Tappenden, Paul; Chilcott, Jim; Brennan, Alan; Squires, Hazel; Glynne-Jones, Rob; Tappenden, Janine

2013-06-01

To assess the feasibility and value of simulating whole disease and treatment pathways within a single model to provide a common economic basis for informing resource allocation decisions. A patient-level simulation model was developed with the intention of being capable of evaluating multiple topics within National Institute for Health and Clinical Excellence's colorectal cancer clinical guideline. The model simulates disease and treatment pathways from preclinical disease through to detection, diagnosis, adjuvant/neoadjuvant treatments, follow-up, curative/palliative treatments for metastases, supportive care, and eventual death. The model parameters were informed by meta-analyses, randomized trials, observational studies, health utility studies, audit data, costing sources, and expert opinion. Unobservable natural history parameters were calibrated against external data using Bayesian Markov chain Monte Carlo methods. Economic analysis was undertaken using conventional cost-utility decision rules within each guideline topic and constrained maximization rules across multiple topics. Under usual processes for guideline development, piecewise economic modeling would have been used to evaluate between one and three topics. The Whole Disease Model was capable of evaluating 11 of 15 guideline topics, ranging from alternative diagnostic technologies through to treatments for metastatic disease. The constrained maximization analysis identified a configuration of colorectal services that is expected to maximize quality-adjusted life-year gains without exceeding current expenditure levels. This study indicates that Whole Disease Model development is feasible and can allow for the economic analysis of most interventions across a disease service within a consistent conceptual and mathematical infrastructure. This disease-level modeling approach may be of particular value in providing an economic basis to support other clinical guidelines. Copyright © 2013 International Society for Pharmacoeconomics and Outcomes Research (ISPOR). Published by Elsevier Inc. All rights reserved.

A mixed methods descriptive investigation of readiness to change in rural hospitals participating in a tele-critical care intervention

PubMed Central

2013-01-01

Background Telemedicine technology can improve care to patients in rural and medically underserved communities yet adoption has been slow. The objective of this study was to study organizational readiness to participate in an academic-community hospital partnership including clinician education and telemedicine outreach focused on sepsis and trauma care in underserved, rural hospitals. Methods This is a multi-method, observational case study. Participants included staff from 4 participating rural South Carolina hospitals. Using a readiness-for-change model, we evaluated 5 general domains and the related factors or topics of organizational context via key informant interviews (n=23) with hospital leadership and staff, compared these to data from hospital staff surveys (n=86) and triangulated data with investigators’ observational reports. Survey items were grouped into 4 categories (based on content and fit with conceptual model) and scored, allowing regression analyses for inferential comparisons to assess factors related to receptivity toward the telemedicine innovation. Results General agreement existed on the need for the intervention and feasibility of implementation. Previous experience with a telemedicine program appeared pivotal to enthusiasm. Perception of need, task demands and resource need explained nearly 50% of variation in receptivity. Little correlation emerged with hospital or ED leadership culture and support. However qualitative data and investigator observations about communication and differing support among disciplines and between staff and leadership could be important to actual implementation. Conclusions A mixed methods approach proved useful in assessing organizational readiness for change in small organizations. Further research on variable operational definitions, potential influential factors, appropriate and feasible methods and valid instruments for such research are needed. PMID:23360332

The Effect of a Conceptual Change Approach on Understanding of Students' Chemical Equilibrium Concepts

ERIC Educational Resources Information Center

Atasoy, Basri; Akkus, Huseyin; Kadayifci, Hakki

2009-01-01

The purpose of this study was to compare the effects of a conceptual change approach over traditional instruction on tenth-grade students' conceptual achievement in understanding chemical equilibrium. The study was conducted in two classes of the same teacher with participation of a total of 44 tenth-grade students. In this study, a…

Effect of Technology Enhanced Conceptual Change Texts on Students' Understanding of Buoyant Force

ERIC Educational Resources Information Center

Ozkan, Gulbin; Selcuk, Gamze Sezgin

2015-01-01

In this study, the effect of technology enhanced conceptual change texts on elementary school students' understanding of buoyant force was investigated. The conceptual change texts (written forms) used in this study are proven for effectiveness and are enriched by using technology support in this study. These texts were tried out on two groups. A…

Conceptual Frameworks in the Doctoral Research Process: A Pedagogical Model

ERIC Educational Resources Information Center

Berman, Jeanette; Smyth, Robyn

2015-01-01

This paper contributes to consideration of the role of conceptual frameworks in the doctoral research process. Through reflection on the two authors' own conceptual frameworks for their doctoral studies, a pedagogical model has been developed. The model posits the development of a conceptual framework as a core element of the doctoral…

Elementary School Teachers' Familiarity, Conceptual Knowledge, and Interest in Light

ERIC Educational Resources Information Center

Mumba, Frackson; Mbewe, Simon; Chabalengula, Vivien M.

2015-01-01

This study explored elementary school teachers' familiarity, conceptual knowledge, and interest in learning more about light and its related concepts. This study also sought to establish the relationship between elementary school teachers' familiarity, conceptual knowledge, and interest in learning light concepts. Sixty-six lower and upper…

Transformative Learning through Conceptual Metaphors: Simile, Metaphor, and Analogy as Levers for Learning

ERIC Educational Resources Information Center

Hoggan, Chad

2014-01-01

This article presents findings from a research study wherein participants demonstrated the use of similes, metaphors, and analogies, termed "conceptual metaphors," in response to disorienting dilemmas instigated by breast cancer. In this qualitative case study of 18 breast cancer survivors, conceptual metaphors were used in three…

Conceptual Understanding of Multiplicative Properties through Endogenous Digital Game Play

ERIC Educational Resources Information Center

Denham, Andre

2012-01-01

This study purposed to determine the effect of an endogenously designed instructional game on conceptual understanding of the associative and distributive properties of multiplication. Additional this study sought to investigate if performance on measures of conceptual understanding taken prior to and after game play could serve as predictors of…

Examining the Conceptualizations, Perceptions, and Practices of Adolescent Writers

ERIC Educational Resources Information Center

Werderich, Donna E.; Armstrong, Sonya L.

2013-01-01

In this article, the authors describe a mixed-methods study in which an adapted Motivation to Write Profile (MWP)--the CLMWP--was used to investigate the conceptualizations, perceptions, and practices of adolescent writers. Results of this study suggested that participants held differing conceptualizations of writing, depending on the context. In…

From the School Health Education Study to the National Health Education Standards: Concepts Endure

ERIC Educational Resources Information Center

Nobiling, Brandye D.; Lyde, Adrian R.

2015-01-01

Background: The landmark School Health Education Study (SHES) project influenced by the conceptual approach to teaching and learning provides perspective on modern school health instruction. Conceptual education, the cornerstone of the SHES curriculum framework (CF), "Health Education: A Conceptual Approach to Curriculum Design," fosters…

Understanding Nursing Home Worker Conceptualizations about Good Care

ERIC Educational Resources Information Center

Chung, Gawon

2013-01-01

This study explored how direct care workers in nursing homes conceptualize good care and how their conceptualizations are influenced by external factors surrounding their work environment and the relational dynamics between them and residents. Study participants were drawn from a local service employees' union, and in-depth interviews were…

Other-Regulation in Collaborative Groups: Implications for Regulation Quality

ERIC Educational Resources Information Center

Rogat, Toni Kempler; Adams-Wiggins, Karlyn R.

2014-01-01

The current study examines variation in other-regulation, conceptualized as efforts by one student to regulate their group's work. This study extends research which has conceptualized other-regulation as temporarily guiding others' conceptual understanding and skill development by broadening the spectrum of other-regulation to include…

Understanding Early Elementary Children's Conceptual Knowledge of Plant Structure and Function through Drawings

ERIC Educational Resources Information Center

Anderson, Janice L.; Ellis, Jane P.; Jones, Alan M.

2014-01-01

This study examined children's drawings to explain children's conceptual understanding of plant structure and function. The study explored whether the children's drawings accurately reflect their conceptual understanding about plants in a manner that can be interpreted by others. Drawing, survey, interview, and observational data were collected…

Diagnostic and Remedial Learning Strategy Based on Conceptual Graphs

ERIC Educational Resources Information Center

Jong, BinShyan; Lin, TsongWuu; Wu, YuLung; Chan, Teyi

2004-01-01

Numerous scholars have applied conceptual graphs for explanatory purposes. This study devised the Remedial-Instruction Decisive path (RID path) algorithm for diagnosing individual student learning situation. This study focuses on conceptual graphs. According to the concepts learned by students and the weight values of relations among these…

The influence of formative assessments on student motivation, achievement, and conceptual change

NASA Astrophysics Data System (ADS)

Yin, Yue

2005-07-01

This study connected research on formative assessment, motivation, and conceptual change. In particular, it examined three research questions: (1) Can formative assessment improve students' motivational beliefs? (2) Can formative assessment improve students' achievement in science and bring about conceptual change? and (3) Are students' science achievement and conceptual change correlated with their motivational beliefs? Formative assessment in this study refers to assessments embedded in an inquiry-based curriculum. To answer those questions, a randomized experiment was conducted. One thousand and two 6th or 7th graders of 12 teachers in 12 different schools in six states participated in the study. The 12 teachers were matched in pairs and randomly assigned to the experimental and control group. The experimental group employed embedded formative assessments while teaching a science curriculum unit and the control group taught the same unit without formative assessments. All the students were given a motivation survey and one or more achievement tests at pre- and posttest. By comparing the experimental and control students' motivation and achievement scores at pretest and posttest, I examined whether the formative assessment treatment affected students' motivation, learning, and conceptual change. By correlating students' posttest motivation, achievement as well as conceptual change scores, I examined whether students' motivation was related to their achievement and conceptual change. Analyses indicated that, the embedded assessments used by the experimental group did not significantly influence students' motivation, achievement, or conceptual change compared to students in the control group. Most motivation beliefs were correlated with students' achievement in a way similar to what has been reported in the literature. They were not correlated with students' conceptual change scores as hypothesized. Teachers, as well as some contextual factors associated with teachers, were extremely influential on students' motivation, achievement, and conceptual change; teacher effects overshadowed the treatment effect. This study revealed many of the challenges and problems teachers, researchers and randomized experiments are likely to encounter. It also highlighted the difficulty and importance of high-fidelity formative assessment implementation. Finally, it suggested that a cognitive approach in studying conceptual change still has great value to further research.

Conceptual design of an integrated hydrothermal liquefaction and biogas plant for sustainable bioenergy production.

PubMed

Hoffmann, Jessica; Rudra, Souman; Toor, Saqib S; Holm-Nielsen, Jens Bo; Rosendahl, Lasse A

2013-02-01

Initial process studies carried out in Aspen Plus on an integrated thermochemical conversion process are presented herein. In the simulations, a hydrothermal liquefaction (HTL) plant is combined with a biogas plant (BP), such that the digestate from the BP is converted to a biocrude in the HTL process. This biorefinery concept offers a sophisticated and sustainable way of converting organic residuals into a range of high-value biofuel streams in addition to combined heat and power (CHP) production. The primary goal of this study is to provide an initial estimate of the feasibility of such a process. By adding a diesel-quality-fuel output to the process, the product value is increased significantly compared to a conventional BP. An input of 1000 kg h(-1) manure delivers approximately 30-38 kg h(-1) fuel and 38-61 kg h(-1) biogas. The biogas can be used to upgrade the biocrude, to supply the gas grid or for CHP. An estimated 62-84% of the biomass energy can be recovered in the biofuels. Copyright © 2012 Elsevier Ltd. All rights reserved.

Using personal qualities assessment to measure the moral orientation and personal qualities of medical students in a non-Western culture.

PubMed

Tsou, Kuo-Inn; Lin, Chaou-Shune; Cho, Shu-Ling; Powis, David; Bore, Miles; Munro, Don; Sze, Daniel Man-Yuen; Wu, Hsi-Chin; Hsieh, Ming-Shium; Lin, Chyi-Her

2013-06-01

How to select candidates with appropriate personal qualities for medical school is an important issue. This study examined the psychometric properties and group differences of the Personal Qualities Assessment (PQA) to test the feasibility of using it as a tool to assess the medical school applicants in a non-Western culture. Seven hundred forty-six medical students in Taiwan completed two psychometric measures: Mojac to assess moral orientation and NACE to assess four aspects of interpersonal relationships. Thirty-one students completed the tests twice to establish test-retest reliability. A subsample of 127 students also completed a measure of the "Big Five" personality traits to examine the construct validity of these scales. Both Mojac and NACE had acceptable internal consistency and test-retest reliability. Conceptually, coherent and significant relationships were observed between test components and between the NACE and Big Five. NACE but not Mojac varied significantly between different sociodemographic groups. Both tests demonstrated acceptable psychometric properties. However, the predictive validity of PQA requires future studies.

Automation and robotics human performance

NASA Technical Reports Server (NTRS)

Mah, Robert W.

1990-01-01

The scope of this report is limited to the following: (1) assessing the feasibility of the assumptions for crew productivity during the intra-vehicular activities and extra-vehicular activities; (2) estimating the appropriate level of automation and robotics to accomplish balanced man-machine, cost-effective operations in space; (3) identifying areas where conceptually different approaches to the use of people and machines can leverage the benefits of the scenarios; and (4) recommending modifications to scenarios or developing new scenarios that will improve the expected benefits. The FY89 special assessments are grouped into the five categories shown in the report. The high level system analyses for Automation & Robotics (A&R) and Human Performance (HP) were performed under the Case Studies Technology Assessment category, whereas the detailed analyses for the critical systems and high leverage development areas were performed under the appropriate operations categories (In-Space Vehicle Operations or Planetary Surface Operations). The analysis activities planned for the Science Operations technology areas were deferred to FY90 studies. The remaining activities such as analytic tool development, graphics/video demonstrations and intelligent communicating systems software architecture were performed under the Simulation & Validations category.

Study on data model of large-scale urban and rural integrated cadastre

NASA Astrophysics Data System (ADS)

Peng, Liangyong; Huang, Quanyi; Gao, Dequan

2008-10-01

Urban and Rural Integrated Cadastre (URIC) has been the subject of great interests for modern cadastre management. It is highly desirable to develop a rational data model for establishing an information system of URIC. In this paper, firstly, the old cadastral management mode in China was introduced, the limitation was analyzed, and the conception of URIC and its development course in China were described. Afterwards, based on the requirements of cadastre management in developed region, the goal of URIC and two key ideas for realizing URIC were proposed. Then, conceptual management mode was studied and a data model of URIC was designed. At last, based on the raw data of land use survey with a scale of 1:1000 and urban conversional cadastral survey with a scale of 1:500 in Jiangyin city, a well-defined information system of URIC was established according to the data model and an uniform management of land use and use right and landownership in urban and rural area was successfully realized. Its feasibility and practicability was well proved.

Nuclear medicine and imaging research (quantitative studies in radiopharmaceutical science)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cooper, M.D.; Beck, R.N.

1990-09-01

This is a report of progress in Year Two (January 1, 1990--December 31, 1990) of Grant FG02-86ER60438, Quantitative Studies in Radiopharmaceutical Science,'' awarded for the three-year period January 1, 1989--December 31, 1991 as a competitive renewal following site visit in the fall of 1988. This program addresses the problems involving the basic science and technology underlying the physical and conceptual tools of radioactive tracer methodology as they relate to the measurement of structural and functional parameters of physiologic importance in health and disease. The principal tool is quantitative radionuclide imaging. The overall objective of this program is to further themore » development and transfer of radiotracer methodology from basic theory to routine clinical practice in order that individual patients and society as a whole will receive the maximum net benefit from the new knowledge gained. The focus of the research is on the development of new instruments and radiopharmaceuticals, and the evaluation of these through the phase of clinical feasibility. 25 refs., 13 figs., 1 tab.« less

Evaluation of mobility impacts of advanced information systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Peeta, S.; Poonuru, K.; Sinha, K.

2000-06-01

Advanced technologies under the aegis of advanced traveler information systems and advanced traffic management systems are being employed to address the debilitating traffic congestion problem. Broadly identified under the label intelligent transportation systems (ITS), they focus on enhancing the efficiency of the existing roadway utilization. Though ITS has transitioned from the conceptual framework stage to the operational test phase that analyzes real-world feasibility, studies that systematically quantify the multidimensional real-world impacts of these technologies in terms of mobility, safety, and air quality, are lacking. This paper proposes a simulation-based framework to address the mobility impacts of these technologies through themore » provision of information to travelers. The information provision technologies are labeled as advanced information systems (AIS), and include pretrip information, en route information, variable message signs, and combinations thereof. The primary focus of the paper is to evaluate alternative AIS technologies using the heavily traveled Borman Expressway corridor in northwestern Indiana as a case study. Simulation results provide insights into the mobility impacts of AIS technologies, and contrast the effectiveness of alternative information provision sources and strategies.« less

MisTec - A software application for supporting space exploration scenario options and technology development analysis and planning

NASA Technical Reports Server (NTRS)

Horsham, Gary A. P.

1992-01-01

This structure and composition of a new, emerging software application, which models and analyzes space exploration scenario options for feasibility based on technology development projections is presented. The software application consists of four main components: a scenario generator for designing and inputting scenario options and constraints; a processor which performs algorithmic coupling and options analyses of mission activity requirements and technology capabilities; a results display which graphically and textually shows coupling and options analysis results; and a data/knowledge base which contains information on a variety of mission activities and (power and propulsion) technology system capabilities. The general long-range study process used by NASA to support recent studies is briefly introduced to provide the primary basis for comparison for discussing the potential advantages to be gained from developing and applying this kind of application. A hypothetical example of a scenario option to facilitate the best conceptual understanding of what the application is, how it works, or the operating methodology, and when it might be applied is presented.

Rotor systems research aircraft predesign study. Volume 2: Conceptual study report

NASA Technical Reports Server (NTRS)

Schmidt, S. A.; Linden, A. W.

1972-01-01

The overall feasibility of the technical requirements and concepts for a rotor system research aircraft (RSRA) was determined. The designs of two aircraft were then compared against the RSRA requirements. One of these is an all new aircraft specifically designed as an RSRA vehicle. A new main rotor, transmission, wings, and fuselage are included in this design. The second aircraft uses an existing Sikorsky S-61 main rotor, an S-61 roller gearbox, and a highly modified Sikorsky S-67 airframe. The wing for this aircraft is a new design. Both aircraft employ a fan-in-fin anti-torque/yaw control system, T58-GE-16 engines for rotor power, and TF34-GE-2 turbofans for auxiliary thrust. Each aircraft meets the basic requirements and goals of the program. The all new aircraft has inflight variable main rotor shaft tilt, a side-by-side cockpit seating arrangement, and is slightly faster in the compound mode. It is also somewhat lighter since it uses new dynamic components specifically designed for the RSRA. Preliminary development plans, including schedules and costs, were prepared for both of these aircraft.

MisTec: A software application for supporting space exploration scenario options and technology development analysis and planning

NASA Technical Reports Server (NTRS)

Horsham, Gary A. P.

1991-01-01

The structure and composition of a new, emerging software application, which models and analyzes space exploration scenario options for feasibility based on technology development projections is presented. The software application consists of four main components: a scenario generator for designing and inputting scenario options and constraints; a processor which performs algorithmic coupling and options analyses of mission activity requirements and technology capabilities; a results display which graphically and textually shows coupling and options analysis results; and a data/knowledge base which contains information on a variety of mission activities and (power and propulsion) technology system capabilities. The general long-range study process used by NASA to support recent studies is briefly introduced to provide the primary basis for comparison for discussing the potential advantages to be gained from developing and applying this king of application. A hypothetical example of a scenario option to facilitate the best conceptual understanding of what the application is, how it works, or the operating methodology, and when it might be applied is presented.

Development of DEMO-FNS tokamak for fusion and hybrid technologies

NASA Astrophysics Data System (ADS)

Kuteev, B. V.; Azizov, E. A.; Alexeev, P. N.; Ignatiev, V. V.; Subbotin, S. A.; Tsibulskiy, V. F.

2015-07-01

The history of fusion-fission hybrid systems based on a tokamak device as an extremely efficient DT-fusion neutron source has passed through several periods of ample research activity in the world since the very beginning of fusion research in the 1950s. Recently, a new roadmap of the hybrid program has been proposed with the goal to build a pilot hybrid plant (PHP) in Russia by 2030. Development of the DEMO-FNS tokamak for fusion and hybrid technologies, which is planned to be built by 2023, is the key milestone on the path to the PHP. This facility is in the phase of conceptual design aimed at providing feasibility studies for a full set of steady state tokamak technologies at a fusion energy gain factor Q ˜ 1, fusion power of ˜40 MW and opportunities for testing a wide range of hybrid technologies with the emphasis on continuous nuclide processing in molten salts. This paper describes the project motivations, its current status and the key issues of the design.

Transceiver optics for interplanetary communications

NASA Astrophysics Data System (ADS)

Roberts, W. T.; Farr, W. H.; Rider, B.; Sampath, D.

2017-11-01

In-situ interplanetary science missions constantly push the spacecraft communications systems to support successively higher downlink rates. However, the highly restrictive mass and power constraints placed on interplanetary spacecraft significantly limit the desired bandwidth increases in going forward with current radio frequency (RF) technology. To overcome these limitations, we have evaluated the ability of free-space optical communications systems to make substantial gains in downlink bandwidth, while holding to the mass and power limits allocated to current state-of-the-art Ka-band communications systems. A primary component of such an optical communications system is the optical assembly, comprised of the optical support structure, optical elements, baffles and outer enclosure. We wish to estimate the total mass that such an optical assembly might require, and assess what form it might take. Finally, to ground this generalized study, we should produce a conceptual design, and use that to verify its ability to achieve the required downlink gain, estimate it's specific optical and opto-mechanical requirements, and evaluate the feasibility of producing the assembly.

Major hydrogeochemical processes in an acid mine drainage affected estuary.

PubMed

Asta, Maria P; Calleja, Maria Ll; Pérez-López, Rafael; Auqué, Luis F

2015-02-15

This study provides geochemical data with the aim of identifying and quantifying the main processes occurring in an Acid Mine Drainage (AMD) affected estuary. With that purpose, water samples of the Huelva estuary were collected during a tidal half-cycle and ion-ion plots and geochemical modeling were performed to obtain a general conceptual model. Modeling results indicated that the main processes responsible for the hydrochemical evolution of the waters are: (i) the mixing of acid fluvial water with alkaline ocean water; (ii) precipitation of Fe oxyhydroxysulfates (schwertmannite) and hydroxides (ferrihydrite); (iii) precipitation of Al hydroxysulfates (jurbanite) and hydroxides (amorphous Al(OH)3); (iv) dissolution of calcite; and (v) dissolution of gypsum. All these processes, thermodynamically feasible in the light of their calculated saturation states, were quantified by mass-balance calculations and validated by reaction-path calculations. In addition, sorption processes were deduced by the non-conservative behavior of some elements (e.g., Cu and Zn). Copyright © 2014 Elsevier Ltd. All rights reserved.

Feasibility and concept study to convert the NASA/AMES vertical motion simulator to a helicopter simulator

NASA Technical Reports Server (NTRS)

Belsterling, C. A.; Chou, R. C.; Davies, E. G.; Tsui, K. C.

1978-01-01

The conceptual design for converting the vertical motion simulator (VMS) to a multi-purpose aircraft and helicopter simulator is presented. A unique, high performance four degrees of freedom (DOF) motion system was developed to permanently replace the present six DOF synergistic system. The new four DOF system has the following outstanding features: (1) will integrate with the two large VMS translational modes and their associated subsystems; (2) can be converted from helicopter to fixed-wing aircraft simulation through software changes only; (3) interfaces with an advanced cab/visual display system of large dimensions; (4) makes maximum use of proven techniques, convenient materials and off-the-shelf components; (5) will operate within the existing building envelope without modifications; (6) can be built within the specified weight limit and avoid compromising VMS performance; (7) provides maximum performance with a minimum of power consumption; (8) simple design minimizes coupling between motions and maximizes reliability; and (9) can be built within existing budgetary figures.

Conceptual design of a hybrid Ge:Ga detector array

NASA Technical Reports Server (NTRS)

Parry, C. M.

1984-01-01

For potential applications in space infrared astronomy missions such as the Space Infrared Telescope Facility and the Large Deployable Reflector, integrated arrays of long-wavelength detectors are desired. The results of a feasibility study which developed a design for applying integrated array techniques to a long-wavelength (gallium-doped germanium) material to achieve spectral coverage between 30 and 200 microns are presented. An approach which builds up a two-dimensional array by stacking linear detector modules is presented. The spectral response of the Ge:Ga detectors is extended to 200 microns by application of uniaxial stress to the stack of modules. The detectors are assembled with 1 mm spacing between the elements. Multiplexed readout of each module is accomplished with integration sampling of a metal-oxide-semiconductor (MOS) switch chip. Aspects of the overall design, including the anticipated level of particle effects on the array in the space environment, a transparent electrode design for 200 microns response, estimates of optical crosstalk, and mechanical stress design calculations are included.

Preliminary scramjet design for hypersonic airbreathing missile application

NASA Technical Reports Server (NTRS)

Carlson, C. H.

1983-01-01

A conceptual design study of a scramjet engine was conducted for a hypersonic surface to air missile (HYSAM). The definition of the engine was based upon the requirements of accelerating the HYSAM from Mach 4 at 20,000 feet to Mach 6 at 100,000 feet and the cruise conditions at Mach 6. The resulting external and internal environmental conditions were used by various engineering disciplines performing design, stress and heat transfer analysis. A detailed structural analysis was conducted along with an indepth thermal analysis. Structurally all the components within the system exhibit positive margins of safety. A feasible concept was defined which uses state-of-the-art materials and existing TMC technology. The engine basically consists of a three dimensional carbon/carbon combustor/nozzle secured to an FS-85 columbium inlet. The carbon/carbon liner is sheathed with carbon felt insulation to thermally protect the FS-85 structure and skin. The thermal analysis of the engine indicates that a thermally viable configuration exists.

Experience gained with the Synroc demonstration plant at ANSTO and its relevance to plutonium immobilization

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jostsons, A.; Ridal, A.; Mercer, D.J.

1996-05-01

The Synroc Demonstration Plant (SDP) was designed and constructed at Lucas Heights to demonstrate the feasibility of Synroc production on a commercial scale (10 kg/hr) with simulated Purex liquid HLW. Since commissioning of the SDP in 1987, over 6000 kg of Synroc has been fabricated with a range of feeds and waste loadings. The SDP utilises uniaxial hot-pressing to consolidate Synroc. Pressureless sintering and hot-isostatic pressing have also been studied at smaller scales. The results of this extensive process development have been incorporated in a conceptual design for a radioactive plant to condition HLW from a reprocessing plant with amore » capacity to treat 800 tpa of spent LWR fuel. Synroic containing TRU, including Pu, and fission products has been fabricated and characterised in a glove-box facility and hot cells, respectively. The extensive experience in processing of Synroc over the past 15 years is summarised and its relevance to immobilization of surplus plutonium is discussed.« less

Advanced catalytic combustors for low pollutant emissions, phase 1

NASA Technical Reports Server (NTRS)

Dodds, W. J.

1979-01-01

The feasibility of employing the known attractive and distinguishing features of catalytic combustion technology to reduce nitric oxide emissions from gas turbine engines during subsonic, stratospheric cruise operation was investigated. Six conceptual combustor designs employing catalytic combustion were defined and evaluated for their potential to meet specific emissions and performance goals. Based on these evaluations, two parallel-staged, fixed-geometry designs were identified as the most promising concepts. Additional design studies were conducted to produce detailed preliminary designs of these two combustors. Results indicate that cruise nitric oxide emissions can be reduced by an order of magnitude relative to current technology levels by the use of catalytic combustion. Also, these combustors have the potential for operating over the EPA landing-takeoff cycle and at cruise with a low pressure drop, high combustion efficiency and with a very low overall level of emission pollutants. The use of catalytic combustion, however, requires advanced technology generation in order to obtain the time-temperature catalytic reactor performance and durability required for practical aircraft engine combustors.

Performance of biofuel processes utilising separate lignin and carbohydrate processing.

PubMed

Melin, Kristian; Kohl, Thomas; Koskinen, Jukka; Hurme, Markku

2015-09-01

Novel biofuel pathways with increased product yields are evaluated against conventional lignocellulosic biofuel production processes: methanol or methane production via gasification and ethanol production via steam-explosion pre-treatment. The novel processes studied are ethanol production combined with methanol production by gasification, hydrocarbon fuel production with additional hydrogen produced from lignin residue gasification, methanol or methane synthesis using synthesis gas from lignin residue gasification and additional hydrogen obtained by aqueous phase reforming in synthesis gas production. The material and energy balances of the processes were calculated by Aspen flow sheet models and add on excel calculations applicable at the conceptual design stage to evaluate the pre-feasibility of the alternatives. The processes were compared using the following criteria: energy efficiency from biomass to products, primary energy efficiency, GHG reduction potential and economy (expressed as net present value: NPV). Several novel biorefinery concepts gave higher energy yields, GHG reduction potential and NPV. Copyright © 2015 Elsevier Ltd. All rights reserved.

Examining the Factors That Influence Students' Science Learning Processes and Their Learning Outcomes: 30 Years of Conceptual Change Research

ERIC Educational Resources Information Center

Lin, Jing-Wen; Yen, Miao-Hsuan; Liang, Jia-Chi; Chiu, Mei-Hung; Guo, Chorng-Jee

2016-01-01

This study used content analysis to examine the most studied conceptual change factors that influence students' science learning processes and their learning outcomes. The reviewed research included empirical studies published since Posner et al. proposed their conceptual change model 30 years ago (from 1982 to 2011). One hundred sixteen SSCI…

DOE Office of Scientific and Technical Information (OSTI.GOV)

Silva, R.A.; Cron, J.

This design analysis has shown that, on a conceptual level, the emplacement of drip shields is feasible with current technology and equipment. A plan for drip shield emplacement was presented using a Drip Shield Transporter, a Drip Shield Emplacement Gantry, a locomotive, and a Drip Shield Gantry Carrier. The use of a Drip Shield Emplacement Gantry as an emplacement concept results in a system that is simple, reliable, and interfaces with the numerous other exising repository systems. Using the Waste Emplacement/Retrieval System design as a basis for the drip shield emplacement concept proved to simplify the system by using existingmore » equipment, such as the gantry carrier, locomotive, Electrical and Control systems, and many other systems, structures, and components. Restricted working envelopes for the Drip Shield Emplacement System require further consideration and must be addressed to show that the emplacement operations can be performed as the repository design evolves. Section 6.1 describes how the Drip Shield Emplacement System may use existing equipment. Depending on the length of time between the conclusion of waste emplacement and the commencement of drip shield emplacement, this equipment could include the locomotives, the gantry carrier, and the electrical, control, and rail systems. If the exisiting equipment is selected for use in the Drip Shield Emplacement System, then the length of time after the final stages of waste emplacement and start of drip shield emplacement may pose a concern for the life cycle of the system (e.g., reliability, maintainability, availability, etc.). Further investigation should be performed to consider the use of existing equipment for drip shield emplacement operations. Further investigation will also be needed regarding the interfaces and heat transfer and thermal effects aspects. The conceptual design also requires further design development. Although the findings of this analysis are accurate for the assumptions made, further refinements of this analysis are needed as the project parameters change. The designs of the drip shield, the Emplacement Drift, and the other drip shield emplacement equipment all have a direct effect on the overall design feasibility.« less

Facilities for Passenger Movement to Decongest Underground Stations

NASA Astrophysics Data System (ADS)

Gupta, Sumana

2014-12-01

Underground rail network partially solves surface congestion problems in busy cities. Presently it is becoming overcrowded causing inconvenience to passengers at interchanges in the city cores especially during peak hours and at junction points. A conceptual model is suggested which can be adopted as an integral part of the under ground system to take care of this problem in particular and for greater sustainability of the entire transit system. The concept is to facilitate the passengers desiring interchange to avoid major junctions, to move between junctions, to reduce time of journey, to reduce detour according the situations through which a route moves. Primarily the model proposes additional connection between chosen stations mechanized with the help of travellators. The approach to decentralize the crowd can have several advantages. Firstly it allows smooth passenger dispersal. It helps in faster movement of passengers to destination. The model may be adopted in various situations with required modifications. This will result in accommodating more trips, comfortable journey and higher sustainability of the mass transit system. The problem and a feasible method of handling it have only been identified in this paper through review of the plans. An in-depth analysis for practical applicability of the proposed model in different stations has not been conducted. Feasibility study is necessary to be conducted before the implementation of the model at specific junctions. The concept proposed in the paper is different from the existing crowd handling methods and it provides a sustainable long term solution

Mapping tobacco industry strategies in South East Asia for action planning and surveillance

PubMed Central

Stillman, F; Hoang, M; Linton, R; Ritthiphakdee, B; Trochim, W

2008-01-01

Objective: To develop a comprehensive conceptual framework of tobacco industry tactics in four countries in South East Asia for the purpose of: (1) generating consensus on key areas of importance and feasibility for regional and cross country tobacco industry monitoring and surveillance; (2) developing measures to track and monitor the effects of the tobacco industry and to design counterstrategies; and (3) building capacity to improve tobacco control planning in the participating countries. Design: A structured conceptualisation methodology known as concept mapping was used. The process included brainstorming, sorting and rating of statements describing industry activities. Statistical analyses used multidimensional scaling and cluster analysis. Interpretation of the maps was participatory, using regional tobacco control researchers, practitioners, and policy makers during a face to face meeting. Participants: 31 participants in this study come from the four countries represented in the project along with six people from the Johns Hopkins Blomberg School of Public Health. Conclusions: The map shows eight clusters of industry activities within the four countries. These were arranged into four general sectors: economics, politics, public relations and deception. For project design purposes, the map indicates areas of importance and feasibility for monitoring tobacco industry activities and serves as a basis for an initial discussion about action planning. Furthermore, the development of the map used a consensus building process across different stakeholders or stakeholder agencies and is critical when developing regional, cross border strategies for tracking and surveillance. PMID:18218787

Fiscal year 1976 progress report on a feasibility study evaluating the use of surface penetrators for planetary exploration

NASA Technical Reports Server (NTRS)

Blanchard, M. B.; Oberbeck, V. R.; Bunch, T. E.; Reynolds, R. T.; Canning, T. N.; Jackson, R. W.

1976-01-01

The feasibility of employing penetrators for exploring Mars was examined. Eight areas of interest for key scientific experiments were identified. These include: seismic activity, imaging, geochemistry, water measurement, heatflow, meteorology, magnetometry, and biochemistry. In seven of the eight potential experiment categories this year's progress included: conceptual design, instrument fabrication, instrument performance evaluation, and shock loading of important components. Most of the components survived deceleration testing with negligible performance changes. Components intended to be placed inside the penetrator forebody were tested up to 3,500 g and components intended to be placed on the afterbody were tested up to 21,000 g. A field test program was conducted using tentative Mars penetrator mission constraints. Drop tests were performed at two selected terrestrial analog sites to determine the range of penetration depths for anticipated common Martian materials. Minimum penetration occurred in basalt at Amboy, California. Three full-scale penetrators penetrated 0.4 to 0.9 m into the basalt after passing through 0.3 to 0.5 m of alluvial overburden. Maximum penetration occurred in unconsolidated sediments at McCook, Nebraska. Two full-scale penetrators penetrated 2.5 to 8.5 m of sediment. Impact occurred in two kinds of sediment: loess and layered clay. Deceleration g loads of nominally 2,000 for the forebody and 20,000 for the afterbody did not present serious design problems for potential experiments. Penetrators have successfully impacted into terrestrial analogs of the probable extremes of potential Martian sites.

A framework for performing workplace hazard and risk analysis: a participative ergonomics approach.

PubMed

Morag, Ido; Luria, Gil

2013-01-01

Despite the unanimity among researchers about the centrality of workplace analysis based on participatory ergonomics (PE) as a basis for preventive interventions, there is still little agreement about the necessary of a theoretical framework for providing practical guidance. In an effort to develop a conceptual PE framework, the authors, focusing on 20 studies, found five primary dimensions for characterising an analytical structure: (1) extent of workforce involvement; (2) analysis duration; (3) diversity of reporter role types; (4) scope of analysis and (5) supportive information system for analysis management. An ergonomics analysis carried out in a chemical manufacturing plant serves as a case study for evaluating the proposed framework. The study simultaneously demonstrates the five dimensions and evaluates their feasibility. The study showed that managerial leadership was fundamental to the successful implementation of the analysis; that all job holders should participate in analysing their own workplace and simplified reporting methods contributed to a desirable outcome. This paper seeks to clarify the scope of workplace ergonomics analysis by offering a theoretical and structured framework for providing practical advice and guidance. Essential to successfully implementing the analytical framework are managerial involvement, participation of all job holders and simplified reporting methods.

Change or Durability? The Contribution of Metaconceptual Awareness in Preservice Early Childhood Teachers' Learning of Science Concepts

NASA Astrophysics Data System (ADS)

Saçkes, Mesut; Trundle, Kathy Cabe

2017-06-01

This longitudinal study examined the role of metaconceptual awareness in the change and the durability of preservice teachers' conceptual understandings over the course of several months. Sixteen preservice early childhood teachers participated in the study. Semi-structured interviews were conducted to reveal the participants' conceptual understandings of lunar phases (pre, post, and delayed-post) and level of metaconceptual awareness (delayed-post only). Based on the change and stability in participants' conceptual understandings from pre to post and from post to delayed-post interviews, participants' conceptual understandings were assigned into three groups that described the profile of their long-term conceptual understandings: " decay or stability", " continuous growth", and " growth and stability". The results indicated that participants in the " continuous growth" and " growth and stability" groups had significantly higher metaconceptual awareness scores than participants in the " decay or stability" group. The results provided evidence that metaconceptual awareness plays a more decisive role in the restructuring of conceptual understandings than the durability of conceptual understandings.

Qualitative analysis and conceptual mapping of patient experiences in home health care.

PubMed

Lines, Lisa M; Anderson, Wayne L; Blackmon, Brian D; Pronier, Cristalle R; Allen, Rachael W; Kenyon, Anne E

2018-01-01

This study explored patient experiences in home health care through a literature review, focus groups, and interviews. Our goal was to develop a conceptual map of home health care patient experience domains. The conceptual map identifies technical and personal spheres of care, relating prior studies to new focus group and interview findings and identifying the most important domains of care. Study participants (n = 35) most frequently reported the most important domain as staff who are caring, supportive, patient, empathetic, respectful, and considerate (endorsed by 29% of participants). The conceptual map includes 114 discrete domains.

Risk factors for pressure ulcer development in critically Ill patients: a conceptual model to guide research.

PubMed

Benoit, Richard; Mion, Lorraine

2012-08-01

This paper presents a proposed conceptual model to guide research on pressure ulcer risk in critically ill patients, who are at high risk for pressure ulcer development. However, no conceptual model exists that guides risk assessment in this population. Results from a review of prospective studies were evaluated for design quality and level of statistical reporting. Multivariate findings from studies having high or medium design quality by the National Institute of Health and Clinical Excellence standards were conceptually grouped. The conceptual groupings were integrated into Braden and Bergstrom's (Braden and Bergstrom [1987] Rehabilitation Nursing, 12, 8-12, 16) conceptual model, retaining their original constructs and augmenting their concept of intrinsic factors for tissue tolerance. The model could enhance consistency in research on pressure ulcer risk factors. Copyright © 2012 Wiley Periodicals, Inc.

Towards to an Explanation for Conceptual Change: A Mechanistic Alternative

ERIC Educational Resources Information Center

Rusanen, Anna-Mari

2014-01-01

Conceptual change is one of the most studied fields in science education and psychology of learning. However, there are still some foundational issues in conceptual change research on which no clear consensus has emerged. Firstly, there is no agreement on what changes in belief and concept systems constitute conceptual change and what changes do…

The Influence of Approach and Avoidance Goals on Conceptual Change

ERIC Educational Resources Information Center

Johnson, Marcus Lee; Sinatra, Gale M.

2014-01-01

Recently, conceptual change research has been experiencing a warming trend (G. M. Sinatra, 2005) whereby motivational and affective factors are being explored in the conceptual change process. The purpose of this study is to explore the 2 × 2 framework of achievement goal theory in relation to students' conceptual change learning for a specific…

DEMONSTRATION OF FUEL CELLS TO RECOVER ENERGY FROM LANDFILL GAS - PHASE I FINAL REPORT: CONCEPTUAL STUDY

EPA Science Inventory

The report discusses results of a conceptual design, cost, and evaluation study of energy recovery from landfill gas using a commercial phosphoric acid fuel cell power plant. The conceptual design of the fuel cell energy recovery system is described, and its economic and environm...

Art as Critical Public Pedagogy: A Qualitative Study of Luis Camnitzer and His Conceptual Art

ERIC Educational Resources Information Center

Zorrilla, Ana; Tisdell, Elizabeth J.

2016-01-01

This qualitative study explored the connection between art and adult education for critical consciousness from the perspective and work of conceptual artist, Luis Camnitzer. The theoretical framework is grounded in the critical public pedagogy literature. Data collection methods included interviews with conceptual artist Luis Camnitzer and with…

Why College Students Cheat: A Conceptual Model of Five Factors

ERIC Educational Resources Information Center

Yu, Hongwei; Glanzer, Perry L.; Johnson, Byron R.; Sriram, Rishi; Moore, Brandon

2018-01-01

Though numerous studies have identified factors associated with academic misconduct, few have proposed conceptual models that could make sense of multiple factors. In this study, we used structural equation modeling (SEM) to test a conceptual model of five factors using data from a relatively large sample of 2,503 college students. The results…