Evaluation of ERDA-sponsored coal feed system development
NASA Technical Reports Server (NTRS)
Phen, R. L.; Luckow, W. K.; Mattson, L.; Otth, D.; Tsou, P.
1977-01-01
Coal feeders were evaluated based upon criteria such as technical feasibility, performance (i.e. ability to meet process requirements), projected life cycle costs, and projected development cost. An initial set of feeders was selected based on the feeders' cost savings potential compared with baseline lockhopper systems. Additional feeders were considered for selection based on: (1) increasing the probability of successful feeder development; (2) application to specific processes; and (3) technical merit. A coal feeder development program is outlined.
NASA Technical Reports Server (NTRS)
Mistry, D. K.; Chen, T. N.
1977-01-01
A dry coal screw feeder for feeding coal into coal gasification reactors operating at pressures up to 1500 psig is described. Results on the feeder under several different modes of operation are presented. In addition, three piston feeder concepts and their technical and economical merits are discussed.
Comparing the engineering program feeders from SiF and convention models
NASA Astrophysics Data System (ADS)
Roongruangsri, Warawaran; Moonpa, Niwat; Vuthijumnonk, Janyawat; Sangsuwan, Kampanart
2018-01-01
This research aims to compare the relationship between two types of engineering program feeder models within the technical education systems of Rajamangala University of Technology Lanna (RMUTL), Chiangmai, Thailand. To illustrate, the paper refers to two typologies of feeder models, which are the convention and the school in factory (SiF) models. The new SiF model is developed through a collaborative educational process between the sectors of industry, government and academia, using work-integrated learning. The research methodology were use to compared features of the the SiF model with conventional models in terms of learning outcome, funding budget for the study, the advantages and disadvantages from the point of view of students, professors, the university, government and industrial partners. The results of this research indicate that the developed SiF feeder model is the most pertinent ones as it meet the requirements of the university, the government and the industry. The SiF feeder model showed the ability to yield positive learning outcomes with low expenditures per student for both the family and the university. In parallel, the sharing of knowledge between university and industry became increasingly important in the process, which resulted in the improvement of industrial skills for professors and an increase in industrial based research for the university. The SiF feeder model meets its demand of public policy in supporting a skilled workforce for the industry, which could be an effective tool for the triple helix educational model of Thailand.
An RFID Based Smart Feeder for Hummingbirds.
Ibarra, Vicente; Araya-Salas, Marcelo; Tang, Yu-ping; Park, Charlie; Hyde, Anthony; Wright, Timothy F; Tang, Wei
2015-12-16
We present an interdisciplinary effort to record feeding behaviors and control the diet of a hummingbird species (Phaethornis longirostris, the long-billed hermit or LBH) by developing a Radio Frequency Identification (RFID) based smart feeder. The system contains an RFID reader, a microcontroller, and a servo-controlled hummingbird feeder opener; the system is presented as a tool for studying the cognitive ability of the LBH species. When equipped with glass capsule RFID tags (which are mounted on the hummingbird), the smart feeder can provide specific diets for predetermined sets of hummingbirds at the discretion of biologists. This is done by reading the unique RFID tag on the hummingbirds and comparing the ID number with the pre-programmed ID numbers stored in the smart feeder. The smart feeder records the time and ID of each hummingbird visit. The system data is stored in a readily available SD card and is powered by two 9 V batteries. The detection range of the system is approximately 9-11 cm. Using this system, biologists can assign the wild hummingbirds to different experimental groups and monitor their diets to determine if they develop a preference to any of the available nectars. During field testing, the smart feeder system has demonstrated consistent detection (when compared to detections observed by video-recordings) of RFID tags on hummingbirds and provides pre-designed nectars varying water and sugar concentrations to target individuals. The smart feeder can be applied to other biological and environmental studies in the future.
An RFID Based Smart Feeder for Hummingbirds
Ibarra, Vicente; Araya-Salas, Marcelo; Tang, Yu-ping; Park, Charlie; Hyde, Anthony; Wright, Timothy F.; Tang, Wei
2015-01-01
We present an interdisciplinary effort to record feeding behaviors and control the diet of a hummingbird species (Phaethornis longirostris, the long-billed hermit or LBH) by developing a Radio Frequency Identification (RFID) based smart feeder. The system contains an RFID reader, a microcontroller, and a servo-controlled hummingbird feeder opener; the system is presented as a tool for studying the cognitive ability of the LBH species. When equipped with glass capsule RFID tags (which are mounted on the hummingbird), the smart feeder can provide specific diets for predetermined sets of hummingbirds at the discretion of biologists. This is done by reading the unique RFID tag on the hummingbirds and comparing the ID number with the pre-programmed ID numbers stored in the smart feeder. The smart feeder records the time and ID of each hummingbird visit. The system data is stored in a readily available SD card and is powered by two 9 V batteries. The detection range of the system is approximately 9–11 cm. Using this system, biologists can assign the wild hummingbirds to different experimental groups and monitor their diets to determine if they develop a preference to any of the available nectars. During field testing, the smart feeder system has demonstrated consistent detection (when compared to detections observed by video-recordings) of RFID tags on hummingbirds and provides pre-designed nectars varying water and sugar concentrations to target individuals. The smart feeder can be applied to other biological and environmental studies in the future. PMID:26694402
Peer Assistance and Leadership (PAL) Program. Program Summary.
ERIC Educational Resources Information Center
Thomas, H. Grant, Jr.
This document describes the Peer Assistance and Leadership (PAL) Program, a peer helping program developed by the Austin Independent School District in Austin, Texas. It explains how selected high school students are trained to work as peer facilitators with younger students either on their own campus or from feeder junior high or elementary…
Live Animal Ultrasound Information as a Decision Tool in Replacement Beef Heifer Programs
USDA-ARS?s Scientific Manuscript database
Data from a two-year heifer development program at Mississippi State University were used along with historic stocker heifer, feeder heifer, and bred heifer prices to estimate the value of real-time ultrasound (RTU) data used to sort heifers into groups for sale or for heifer development. Ultrasound...
Ji, Haoran; Wang, Chengshan; Li, Peng; ...
2017-09-20
The integration of distributed generators (DGs) exacerbates the feeder power flow fluctuation and load unbalanced condition in active distribution networks (ADNs). The unbalanced feeder load causes inefficient use of network assets and network congestion during system operation. The flexible interconnection based on the multi-terminal soft open point (SOP) significantly benefits the operation of ADNs. The multi-terminal SOP, which is a controllable power electronic device installed to replace the normally open point, provides accurate active and reactive power flow control to enable the flexible connection of feeders. An enhanced SOCP-based method for feeder load balancing using the multi-terminal SOP is proposedmore » in this paper. Furthermore, by regulating the operation of the multi-terminal SOP, the proposed method can mitigate the unbalanced condition of feeder load and simultaneously reduce the power losses of ADNs. Then, the original non-convex model is converted into a second-order cone programming (SOCP) model using convex relaxation. In order to tighten the SOCP relaxation and improve the computation efficiency, an enhanced SOCP-based approach is developed to solve the proposed model. Finally, case studies are performed on the modified IEEE 33-node system to verify the effectiveness and efficiency of the proposed method.« less
DOE Office of Scientific and Technical Information (OSTI.GOV)
Ji, Haoran; Wang, Chengshan; Li, Peng
The integration of distributed generators (DGs) exacerbates the feeder power flow fluctuation and load unbalanced condition in active distribution networks (ADNs). The unbalanced feeder load causes inefficient use of network assets and network congestion during system operation. The flexible interconnection based on the multi-terminal soft open point (SOP) significantly benefits the operation of ADNs. The multi-terminal SOP, which is a controllable power electronic device installed to replace the normally open point, provides accurate active and reactive power flow control to enable the flexible connection of feeders. An enhanced SOCP-based method for feeder load balancing using the multi-terminal SOP is proposedmore » in this paper. Furthermore, by regulating the operation of the multi-terminal SOP, the proposed method can mitigate the unbalanced condition of feeder load and simultaneously reduce the power losses of ADNs. Then, the original non-convex model is converted into a second-order cone programming (SOCP) model using convex relaxation. In order to tighten the SOCP relaxation and improve the computation efficiency, an enhanced SOCP-based approach is developed to solve the proposed model. Finally, case studies are performed on the modified IEEE 33-node system to verify the effectiveness and efficiency of the proposed method.« less
Robertazzi, Thomas G.; Skiena, Steven; Wang, Kai
2017-08-08
Provided are an apparatus and method for load-balancing of a three-phase electric power distribution system having a multi-phase feeder, including obtaining topology information of the feeder identifying supply points for customer loads and feeder sections between the supply points, obtaining customer information that includes peak customer load at each of the points between each of the feeder sections, performing a phase balancing analysis, and recommending phase assignment at the customer load supply points.
Documentation of the data analysis system for the gamma ray monitor aboard OSO-H
NASA Technical Reports Server (NTRS)
Croteau, S.; Buck, A.; Higbie, P.; Kantauskis, J.; Foss, S.; Chupp, D.; Forrest, D. J.; Suri, A.; Gleske, I.
1973-01-01
The programming system is presented which was developed to prepare the data from the gamma ray monitor on OSO-7 for scientific analysis. The detector, data, and objectives are described in detail. Programs presented include; FEEDER, PASS-1, CAL1, CAL2, PASS-3, Van Allen Belt Predict Program, Computation Center Plot Routine, and Response Function Programs.
DOE Office of Scientific and Technical Information (OSTI.GOV)
Broderick, Robert Joseph; Quiroz, Jimmy Edward; Reno, Matthew J.
2015-11-01
The third solicitation of the California Solar Initiative (CSI) Research, Development, Demonstration and Deployment (RD&D) Program established by the California Public Utility Commission (CPUC) is supporting the Electric Power Research Institute (EPRI), National Renewable Energy Laboratory (NREL), and Sandia National Laboratories (SNL) with collaboration from Pacific Gas and Electric (PG&E), Southern California Edison (SCE), and San Diego Gas and Electric (SDG&E), in research to improve the Utility Application Review and Approval process for interconnecting distributed energy resources to the distribution system. Currently this process is the most time - consuming of any step on the path to generating power onmore » the distribution system. This CSI RD&D solicitation three project has completed the tasks of collecting data from the three utilities, clustering feeder characteristic data to attain representative feeders, detailed modeling of 16 representative feeders, analysis of PV impacts to those feeders, refinement of current screening processes, and validation of those suggested refinements. In this report each task is summarized to produce a final summary of all components of the overall project.« less
Leksrisompong, N; Romero-Sanchez, H; Oviedo-Rondón, E O; Brake, J
2014-07-01
A study was conducted to examine how 2 feeder space allocations during the rearing period followed by 2 feeder space allocations after photostimulation and 2 female feeding to peak programs (fast or slow) affected female broiler breeder reproductive performance and mortality. Sixteen pens of 76 breeder females each were equipped with either 4 tube feeders with a 132 cm circumference pan (7.0 cm/female) or 6 feeders (10.4 cm/female) to 21 wk of age. Thereafter, 64 females were moved to breeding pens, photostimulated, and fed sex-separate from either 3 (6.2 cm/female) or 5 (10.3 cm/female) feeders with either fast or slow feeding to peak feeding programs applied to complete a 2 × 2 × 2 factorial design. Seven males that were separately reared in a similar manner were added per pen. Individual female BW was determined at 6, 20, and 32 wk of age and BW uniformity assessed. Greater feeder space during rearing increased BW at 32 wk of age, whereas greater feeder space during lay or slow feeding to peak decreased BW at 32 wk. There were no differences in BW uniformity. Hens from the 10.4 to 10.3 cm/female combination produced a significantly greater number of eggs as compared with the 7.0 to 10.3 cm/female and 10.4 to 6.2 cm/female combinations with the 7.0 to 6.2 cm/female combination intermediate. Percentage hen-day egg production of the 10.4 to 10.3 cm/female combination hens was significantly greater than all other combinations. Livability was improved in the 10.4 to 10.3 cm/female combination relative to the 7.0 to 10.3 cm/female combination with the others intermediate. The fast feeding to peak program increased yolk weight as well as yolk:albumen ratio at 28 and 30 wk of age, but egg weight did not differ. These data indicated that increased or decreased feeder space between the growing and laying periods did not affect broiler breeder female BW, uniformity, egg weight, fertility, or hatchability. The 10.3 cm/female laying feeder space exhibited the best hen-day egg production in combination with 10.4 cm/pullet rearing but not with 7.0 cm/pullet rearing space. In a similar manner, hen mortality was greater in the 7.0 to 10.3 cm/female feeder space combination that the 10.4 to 10.3 cm/female combination. © 2014 Poultry Science Association Inc.
49 CFR 1151.3 - Contents of application.
Code of Federal Regulations, 2010 CFR
2010-10-01
... 49 Transportation 8 2010-10-01 2010-10-01 false Contents of application. 1151.3 Section 1151.3 Transportation Other Regulations Relating to Transportation (Continued) SURFACE TRANSPORTATION BOARD, DEPARTMENT OF TRANSPORTATION RULES OF PRACTICE FEEDER RAILROAD DEVELOPMENT PROGRAM § 1151.3 Contents of...
A Feeder-Bus Dispatch Planning Model for Emergency Evacuation in Urban Rail Transit Corridors
Wang, Yun; Yan, Xuedong; Zhou, Yu; Zhang, Wenyi
2016-01-01
The mobility of modern metropolises strongly relies on urban rail transit (URT) systems, and such a heavy dependence causes that even minor service interruptions would make the URT systems unsustainable. This study aims at optimally dispatching the ground feeder-bus to coordinate with the urban rails’ operation for eliminating the effect of unexpected service interruptions in URT corridors. A feeder-bus dispatch planning model was proposed for the collaborative optimization of URT and feeder-bus cooperation under emergency situations and minimizing the total evacuation cost of the feeder-buses. To solve the model, a concept of dummy feeder-bus system is proposed to transform the non-linear model into traditional linear programming (ILP) model, i.e., traditional transportation problem. The case study of Line #2 of Nanjing URT in China was adopted to illustrate the model application and sensitivity analyses of the key variables. The modeling results show that as the evacuation time window increases, the total evacuation cost as well as the number of dispatched feeder-buses decrease, and the dispatched feeder-buses need operate for more times along the feeder-bus line. The number of dispatched feeder-buses does not show an obvious change with the increase of parking spot capacity and time window, indicating that simply increasing the parking spot capacity would cause huge waste for the emergent bus utilization. When the unbalanced evacuation demand exists between stations, the more feeder-buses are needed. The method of this study will contribute to improving transportation emergency management and resource allocation for URT systems. PMID:27676179
49 CFR 1151.3 - Contents of application.
Code of Federal Regulations, 2012 CFR
2012-10-01
... 49 Transportation 8 2012-10-01 2012-10-01 false Contents of application. 1151.3 Section 1151.3 Transportation Other Regulations Relating to Transportation (Continued) SURFACE TRANSPORTATION BOARD, DEPARTMENT OF TRANSPORTATION RULES OF PRACTICE FEEDER RAILROAD DEVELOPMENT PROGRAM § 1151.3 Contents of application. (a) The initial application and...
49 CFR 1151.3 - Contents of application.
Code of Federal Regulations, 2013 CFR
2013-10-01
... 49 Transportation 8 2013-10-01 2013-10-01 false Contents of application. 1151.3 Section 1151.3 Transportation Other Regulations Relating to Transportation (Continued) SURFACE TRANSPORTATION BOARD, DEPARTMENT OF TRANSPORTATION RULES OF PRACTICE FEEDER RAILROAD DEVELOPMENT PROGRAM § 1151.3 Contents of application. (a) The initial application and...
NASA Astrophysics Data System (ADS)
Nguyen, Van Xo; Golikov, N. S.
2018-05-01
The structure and kinematics of the two-mass GZS vibratory feeder operation are considered. It is established that the movement of the material's particles on the feeder surface determines its capacity. The development and analysis of the mathematical model of material's particle movement on the two-mass GZS vibratory feeder surface are shown. The results of Matlab optimization of material particles velocity function are given that allows setting rational kinematics of the feeder.
Development of dry coal feeders
NASA Technical Reports Server (NTRS)
Bonin, J. H.; Cantey, D. E.; Daniel, A. D., Jr.; Meyer, J. W.
1977-01-01
Design and fabrication of equipment of feed coal into pressurized environments were investigated. Concepts were selected based on feeder system performance and economic projections. These systems include: two approaches using rotating components, a gas or steam driven ejector, and a modified standpipe feeder concept. Results of development testing of critical components, design procedures, and performance prediction techniques are reviewed.
Faculty Articulation with Feeder High Schools and Local Employers.
ERIC Educational Resources Information Center
Parrott, Marietta
As a first step in developing an articulation plan with feeder high schools, a College of the Sequoias (COS) task force developed and distributed a survey to all full-time faculty members to determine if individual faculty members were articulating with feeder high schools and local businesses, and if they would be willing to participate in an…
Morin, M.; Morehouse, L. G.
1974-01-01
Light and electron microscopy findings in the jejunal mucosa of the normal feeder pig and feeder pigs infected with transmissible gastroenteritis (TGE) virus are reported. Villi in the mid jejunum of the normal feeder pig were elongated, finger shaped and covered with a layer of columnar absorptive cells with a well developed and regular brush border. Severe lesions of villous atrophy were present in all jejunal segments of feeder swine killed 96 hours post infection with TGE virus. Atrophic villi were covered by flat to cuboidal cells with a poorly developed brush border in some areas. In other segments, cells varied in appearance from sub-columnar to columnar type of near normal appearance. The ultrastructure of the jejunal absorptive cells in the normal feeder pig was found to be similar to that described for the jejunal cells of other adult mammals. There were no significant indications of high pinocytotic activity. The epithelial cells covering the atrophic villi of TGE infected pigs had a fine structure similar to that described for the crypt cells, ranging in appearance from very immature to moderately differentiated cells. Microvilli were very short, decreased markedly in number and irregular in arrangement. The terminal web was poorly developed. Strands of rough endoplasmic reticulum were markedly diminished and an increase in free ribosomes was noted. The significance of these observations in explaining pathogenesis of TGE in feeder pigs is discussed. ImagesFig. 1.Fig. 2.Fig. 3.Fig. 4.Fig. 5.Fig. 6.Fig. 7.Fig. 8. PMID:4277743
Functional and aesthetic approach to design of bird feeders
NASA Astrophysics Data System (ADS)
Kukhta, A.; Kukhta, M.
2015-10-01
Anthropogenic objects which load the urban environment negatively affects the human psyche. The alternative is attracting elements of the natural environment into urban environment, of which some of the most frequently identified are birds. Attracting birds in the city is possible by means of feeders and artificial nests, however, both must be harmonious. The aim of this study is to analyze the essential functions of the feeders, and their integration into the environmental design and development of the city. On this basis an original feeder which is convenient for use by birds and attracts people's attention is developed. In this paper we apply comparative analysis of different types of feeders encountered in Tomsk, bird watching, and evaluate usability of different types of feeders from the position of their convenience both for birds and human beings. Historical-cultural analysis for determining features of the architectural and environmental design of Tomsk is carried out, the method allows us to solve engineering problems. In this study the feeder convenient for bird use is designed which blends harmoniously with the architectural design of Tomsk.
Brake, J; Khamidullin, T N; Fisinin, V I
1993-03-01
A series of experiments was conducted in order to develop a feeder grill that would allow broiler breeder males, but not females, to eat. Females are typically excluded from male feeders by increasing the height of the feeder. However, male feeder heights that exclude most females increase the time required for males to consume a given amount of feed 19 to 60%. Typical male feeder height from floor to feeder pan lip in commercial practice is 55 cm, which is about the distance from floor to the head of the male in an erect posture. Females measure about 40 cm in an erect posture. Because the necks of males (8.0 cm) are longer than those of females (6.3 cm), the lip of male feeder pans was extended horizontally 12.7 cm with a wire mesh on the assumption that females could not stretch their necks enough to reach the feed. However, the females learned quickly to perch on the extended lip and eat. Total exclusion of females from the male feeder, regardless of feeder height, was achieved by placing a horizontal upper mesh 5.6 to 10.2 cm above the extended lip, and connecting the upper mesh to the lower extended lip of the feeder with vertical bars spaced 5.1 cm apart. The horizontal upper mesh prevented perching by females and the 5.1-cm spacing of the vertical bars allowed males but not females to reach the feed by inserting their heads and necks up to their shoulders.(ABSTRACT TRUNCATED AT 250 WORDS)
Analytic Considerations and Design Basis for the IEEE Distribution Test Feeders
DOE Office of Scientific and Technical Information (OSTI.GOV)
Schneider, K. P.; Mather, B. A.; Pal, B. C.
For nearly 20 years the Test Feeder Working Group of the Distribution System Analysis Subcommittee has been developing openly available distribution test feeders for use by researchers. The purpose of these test feeders is to provide models of distribution systems that reflect the wide diversity in design and their various analytic challenges. Because of their utility and accessibility, the test feeders have been used for a wide range of research, some of which has been outside the original scope of intended uses. This paper provides an overview of the existing distribution feeder models and clarifies the specific analytic challenges thatmore » they were originally designed to examine. Additionally, the paper will provide guidance on which feeders are best suited for various types of analysis. The purpose of this paper is to provide the original intent of the Working Group and to provide the information necessary so that researchers may make an informed decision on which of the test feeders are most appropriate for their work.« less
Analytic Considerations and Design Basis for the IEEE Distribution Test Feeders
Schneider, K. P.; Mather, B. A.; Pal, B. C.; ...
2017-10-10
For nearly 20 years the Test Feeder Working Group of the Distribution System Analysis Subcommittee has been developing openly available distribution test feeders for use by researchers. The purpose of these test feeders is to provide models of distribution systems that reflect the wide diversity in design and their various analytic challenges. Because of their utility and accessibility, the test feeders have been used for a wide range of research, some of which has been outside the original scope of intended uses. This paper provides an overview of the existing distribution feeder models and clarifies the specific analytic challenges thatmore » they were originally designed to examine. Additionally, the paper will provide guidance on which feeders are best suited for various types of analysis. The purpose of this paper is to provide the original intent of the Working Group and to provide the information necessary so that researchers may make an informed decision on which of the test feeders are most appropriate for their work.« less
A method for the determination of potentially profitable service patterns for commuter air carriers
NASA Technical Reports Server (NTRS)
Ransone, R. K.; Kuhlthau, A. R.; Deptula, D. A.
1975-01-01
A methodology for estimating market conception was developed as a part of the short-haul air transportation program. It is based upon an analysis of actual documents which provide a record of known travel history. Applying this methodology a forecast was made of the demand for an air feeder service between Charlottesville, Virginia and Dulles International Airport. Local business travel vouchers and local travel agent records were selected to provide the documentation. The market was determined to be profitable for an 8-passenger Cessna 402B aircraft flying a 2-hour daily service pattern designed to mesh to the best extent possible with the connecting schedules at Dulles. The Charlottesville - Dulles air feeder service market conception forecast and its methodology are documented.
Continuation Power Flow Analysis for PV Integration Studies at Distribution Feeders
DOE Office of Scientific and Technical Information (OSTI.GOV)
Wang, Jiyu; Zhu, Xiangqi; Lubkeman, David L.
2017-10-30
This paper presents a method for conducting continuation power flow simulation on high-solar penetration distribution feeders. A load disaggregation method is developed to disaggregate the daily feeder load profiles collected in substations down to each load node, where the electricity consumption of residential houses and commercial buildings are modeled using actual data collected from single family houses and commercial buildings. This allows the modeling of power flow and voltage profile along a distribution feeder on a continuing fashion for a 24- hour period at minute-by-minute resolution. By separating the feeder into load zones based on the distance between the loadmore » node and the feeder head, we studied the impact of PV penetration on distribution grid operation in different seasons and under different weather conditions for different PV placements.« less
DOE Office of Scientific and Technical Information (OSTI.GOV)
Not Available
1984-01-12
This report describes the work done under Phase II, the verification testing of the Kinetic Extruder. The main objective of the test program was to determine failure modes and wear rates. Only minor auxiliary equipment malfunctions were encountered. Wear rates indicate useful life expectancy of from 1 to 5 years for wear-exposed components. Recommendations are made for adapting the equipment for pilot plant and commercial applications. 3 references, 20 figures, 12 tables.
DOE Office of Scientific and Technical Information (OSTI.GOV)
Ding, Fei; Pratt, Annabelle; Bialek, Tom
2016-11-21
This paper reports on tools and methodologies developed to study the impact of adding rooftop photovoltaic (PV) systems, with and without the ability to provide voltage support, on the voltage profile of distribution feeders. Simulation results are provided from a study of a specific utility feeder. The simulation model of the utility distribution feeder was built in OpenDSS and verified by comparing the simulated voltages to field measurements. First, we set all PV systems to operate at unity power factor and analyzed the impact on feeder voltages. Then we conducted multiple simulations with voltage support activated for all the smartmore » PV inverters. These included different constant power factor settings and volt/VAR controls.« less
An evaluation of the choice of feeder cell growth arrest for the production of cultured epidermis.
Chugh, Rishi Man; Chaturvedi, Madhusudan; Yerneni, Lakshmana Kumar
2015-12-01
Growth arrested 3T3 cells have been used as feeder cells in human epidermal keratinocyte cultures to produce cultured epidermal autografts for the treatment of burns. The feeder cells were ideally growth-arrested by gamma-irradiation. Alternatively, growth arrest by mitomycin C treatment is a cost effective option. We compared the functional efficacy of these two approaches in keratinocyte cultures by colony forming efficiency, the net growth area of colonies, BrdU labeling and histological features of cultured epidermal sheets. The growth area estimation involved a semi-automated digital technique using the Adobe Photoshop and comprised of isolation and enumeration of red pixels in Rhodamine B-stained keratinocyte colonies. A further refinement of the technique led to the identification of critical steps to increasing the degree of accuracy and enabling its application as an extension of colony formation assay. The results on feeder cell functionality revealed that the gamma irradiated feeders influenced significantly higher colony forming efficiency and larger growth area than the mitomycin C treated feeders. The BrdU labeling study indicated significant stimulation of the overall keratinocyte proliferation by the gamma irradiated feeders. The cultured epidermal sheets produced by gamma feeders were relatively thicker than those produced by mitomycin C feeders. We discussed the clinical utility of mitomycin C feeders from the viewpoint of cost-effective burn care in developing countries. Copyright © 2015 Elsevier Ltd and ISBI. All rights reserved.
Conceptual Design and Analysis of Cold Mass Support of the CS3U Feeder for the ITER
NASA Astrophysics Data System (ADS)
Zhu, Yinfeng; Song, Yuntao; Zhang, Yuanbin; Wang, Zhongwei
2013-06-01
In the International Thermonuclear Experimental Reactor (ITER) project, the feeders are one of the most important and critical systems. To convey the power supply and the coolant for the central solenoid (CS) magnet, 6 sets of CS feeders are employed, which consist mainly of an in-cryostat feeder (ICF), a cryostat feed-through (CFT), an S-bend box (SBB), and a coil terminal box (CTB). To compensate the displacements of the internal components of the CS feeders during operation, sliding cold mass supports consisting of a sled plate, a cylindrical support, a thermal shield, and an external ring are developed. To check the strength of the developed cold mass supports of the CS3U feeder, electromagnetic analysis of the two superconducting busbars is performed by using the CATIA V5 and ANSYS codes based on parametric technology. Furthermore, the thermal-structural coupling analysis is performed based on the obtained results, except for the stress concentration, and the max. stress intensity is lower than the allowable stress of the selected material. It is found that the conceptual design of the cold mass support can satisfy the required functions under the worst case of normal working conditions. All these performed activities will provide a firm technical basis for the engineering design and development of cold mass supports.
ERIC Educational Resources Information Center
Seiverling, Laura; Harclerode, Whitney; Williams, Keith
2014-01-01
The purpose of this study was to examine if sequential presentation with feeder modeling would lead to an increase in bites accepted of new foods compared to sequential presentation without feeder modeling in a typically developing 4-year-old boy with food selectivity. The participant's acceptance of novel foods increased both in the modeling and…
Effects of different feeder layers on culture of bovine embryonic stem cell-like cells in vitro.
Cong, Shan; Cao, Guifang; Liu, Dongjun
2014-12-01
To find a suitable feeder layer is important for successful culture conditions of bovine embryonic stem cell-like cells. In this study, expression of pluripotency-related genes OCT4, SOX2 and NANOG in bovine embryonic stem cell-like cells on mouse embryonic fibroblast feeder layers at 1-5 passages were monitored in order to identify the possible reason that bovine embryonic stem cell-like cells could not continue growth and passage. Here, we developed two novel feeder layers, mixed embryonic fibroblast feeder layers of mouse and bovine embryonic fibroblast at different ratios and sources including mouse fibroblast cell lines. The bovine embryonic stem cell-like cells generated in our study displayed typical stem cell morphology and expressed specific markers such as OCT4, stage-specific embryonic antigen 1 and 4, alkaline phosphatase, SOX2, and NANOG mRNA levels. When feeder layers and cell growth factors were removed, the bovine embryonic stem cell-like cells formed embryoid bodies in a suspension culture. Furthermore, we compared the expression of the pluripotent markers during bovine embryonic stem cell-like cell in culture on mixed embryonic fibroblast feeder layers, including mouse fibroblast cell lines feeder layers and mouse embryonic fibroblast feeder layers by real-time quantitative polymerase chain reaction. Results suggested that mixed embryonic fibroblast and sources including mouse fibroblast cell lines feeder layers were more suitable for long-term culture and growth of bovine embryonic stem cell-like cells than mouse embryonic fibroblast feeder layers. The findings may provide useful experimental data for the establishment of an appropriate culture system for bovine embryonic stem cell lines.
Sharma, Manjinder; Dubey, Pawan K; Kumar, Rajesh; Nath, Amar; Kumar, G Sai; Sharma, G Taru
2013-05-01
Use of somatic cells as a feeder layer to maintain the embryonic stem cells (ESCs) in undifferentiated state limits the stem cell research design, since experimental data may result from a combined ESCs and feeder cell response to various stimuli. Therefore, present study was designed to evaluate the developmental competence of the buffalo ESCs over different homogenous feeders and compare with various extracellular matrices using different concentrations of LIF. Inner cell masses (ICMs) of in vitro hatched blastocysts were cultured onto homologous feeders viz. fetal fibroblast, granulosa and oviductal cell feeder layers and synthetic matrices viz. fibronectin, collagen type I and matrigel in culture medium. Developmental efficiency was found higher for ESCs cultured on fetal fibroblast and granulosa layers (83.33%) followed by fibronectin (77.78%) at 30 ng LIF. Oviductal feeder was found to be the least efficient feeder showing only 11.11% undifferentiated primary ESC colonies at 30 ng LIF. However, neither feeder layer nor synthetic matrix could support the development of primary colonies at 10 ng LIF. Expression of SSEA- 4, TRA-1-60 and Oct-4 were found positive in ESC colonies from all the feeders and synthetic matrices with 20 ng and 30 ng LIF. Fetal fibroblast and granulosa cell while, amongst synthetic matrices, fibronectin were found to be equally efficient to support the growth and maintenance of ESCs pluripotency with 30 ng LIF. This well-defined culture conditions may provide an animal model for culturing human embryonic stem cells in the xeno-free or feeder-free conditions for future clinical applications.
DOE Office of Scientific and Technical Information (OSTI.GOV)
Kamada, Mizuna; Mitsui, Youji, E-mail: y-mitsui8310@hb.tp1.jp; Kumazaki, Tsutomu
2014-10-24
Highlights: • hiPS cell explants formed malignant tumors when SNL76/7 feeder cells were used. • Multi type tumors developed by interaction of SNL76/7 feeder cells with hiPS cells. • Tumorigenic risk occurs by co-culture of hiPS cells with SNL76/7 feeder cells. - Abstract: The potential for tumor formation from transplanted human induced pluripotent stem cell (hiPSC) derivatives represents a high risk in their application to regenerative medicine. We examined the genetic origin and characteristics of tumors, that were formed when 13 hiPSC lines, established by ourselves, and 201B7 hiPSC from Kyoto University were transplanted into severe combined immune-deficient (SCID) mice.more » Though teratomas formed in 58% of mice, five angiosarcomas, one malignant solitary fibrous tumor and one undifferentiated pleomorphic sarcoma formed in the remaining mice. Three malignant cell lines were established from the tumors, which were derived from mitomycin C (MMC)-treated SNL76/7 (MMC-SNL) feeder cells, as tumor development from fusion cells between MMC-SNL and hiPSCs was negative by genetic analysis. While parent SNL76/7 cells produced malignant tumors, neither MMC-SNL nor MMC-treated mouse embryo fibroblast (MEF) produced malignant tumors. When MMC-SNL feeder cells were co-cultured with hiPSCs, growing cell lines were generated, that expressed genes similar to the parent SNL76/7 cells. Thus, hiPSCs grown on MMC-SNL feeder cells have a high risk of generating feeder-derived malignant tumors. The possible mechanism(s) of growth restoration and the formation of multiple tumor types are discussed with respect of the interactions between MMC-SNL and hiPSC.« less
Zou, Qing; Wu, Mingjun; Zhong, Liwu; Fan, Zhaoxin; Zhang, Bo; Chen, Qiang; Ma, Feng
2016-01-01
Various feeder layers have been extensively applied to support the prolonged growth of human pluripotent stem cells (hPSCs) for in vitro cultures. Among them, mouse embryonic fibroblast (MEF) and mouse fibroblast cell line (SNL) are most commonly used feeder cells for hPSCs culture. However, these feeder layers from animal usually cause immunogenic contaminations, which compromises the potential of hPSCs in clinical applications. In the present study, we tested human umbilical cord mesenchymal stem cells (hUC-MSCs) as a potent xeno-free feeder system for maintaining human induced pluripotent stem cells (hiPSCs). The hUC-MSCs showed characteristics of MSCs in xeno-free culture condition. On the mitomycin-treated hUC-MSCs feeder, hiPSCs maintained the features of undifferentiated human embryonic stem cells (hESCs), such as low efficiency of spontaneous differentiation, stable expression of stemness markers, maintenance of normal karyotypes, in vitro pluripotency and in vivo ability to form teratomas, even after a prolonged culture of more than 30 passages. Our study indicates that the xeno-free culture system may be a good candidate for growth and expansion of hiPSCs as the stepping stone for stem cell research to further develop better and safer stem cells. PMID:26882313
Zou, Qing; Wu, Mingjun; Zhong, Liwu; Fan, Zhaoxin; Zhang, Bo; Chen, Qiang; Ma, Feng
2016-01-01
Various feeder layers have been extensively applied to support the prolonged growth of human pluripotent stem cells (hPSCs) for in vitro cultures. Among them, mouse embryonic fibroblast (MEF) and mouse fibroblast cell line (SNL) are most commonly used feeder cells for hPSCs culture. However, these feeder layers from animal usually cause immunogenic contaminations, which compromises the potential of hPSCs in clinical applications. In the present study, we tested human umbilical cord mesenchymal stem cells (hUC-MSCs) as a potent xeno-free feeder system for maintaining human induced pluripotent stem cells (hiPSCs). The hUC-MSCs showed characteristics of MSCs in xeno-free culture condition. On the mitomycin-treated hUC-MSCs feeder, hiPSCs maintained the features of undifferentiated human embryonic stem cells (hESCs), such as low efficiency of spontaneous differentiation, stable expression of stemness markers, maintenance of normal karyotypes, in vitro pluripotency and in vivo ability to form teratomas, even after a prolonged culture of more than 30 passages. Our study indicates that the xeno-free culture system may be a good candidate for growth and expansion of hiPSCs as the stepping stone for stem cell research to further develop better and safer stem cells.
Network Reduction Algorithm for Developing Distribution Feeders for Real-Time Simulators
DOE Office of Scientific and Technical Information (OSTI.GOV)
Nagarajan, Adarsh; Nelson, Austin A; Prabakar, Kumaraguru
As advanced grid-support functions (AGF) become more widely used in grid-connected photovoltaic (PV) inverters, utilities are increasingly interested in their impacts when implemented in the field. These effects can be understood by modeling feeders in real-time simulators and test PV inverters using power hardware-in-the-loop (PHIL) techniques. This paper presents a novel feeder model reduction algorithm using a ruin & reconstruct methodology that enables large feeders to be solved and operated on real-time computing platforms. Two Hawaiian Electric feeder models in Synergi Electric's load flow software were converted to reduced order models in OpenDSS, and subsequently implemented in the OPAL-RT real-timemore » digital testing platform. Smart PV inverters were added to the realtime model with AGF responses modeled after characterizing commercially available hardware inverters. Finally, hardware inverters were tested in conjunction with the real-time model using PHIL techniques so that the effects of AGFs on the feeders could be analyzed.« less
Network Reduction Algorithm for Developing Distribution Feeders for Real-Time Simulators: Preprint
DOE Office of Scientific and Technical Information (OSTI.GOV)
Nagarajan, Adarsh; Nelson, Austin; Prabakar, Kumaraguru
As advanced grid-support functions (AGF) become more widely used in grid-connected photovoltaic (PV) inverters, utilities are increasingly interested in their impacts when implemented in the field. These effects can be understood by modeling feeders in real-time systems and testing PV inverters using power hardware-in-the-loop (PHIL) techniques. This paper presents a novel feeder model reduction algorithm using a Monte Carlo method that enables large feeders to be solved and operated on real-time computing platforms. Two Hawaiian Electric feeder models in Synergi Electric's load flow software were converted to reduced order models in OpenDSS, and subsequently implemented in the OPAL-RT real-time digitalmore » testing platform. Smart PV inverters were added to the real-time model with AGF responses modeled after characterizing commercially available hardware inverters. Finally, hardware inverters were tested in conjunction with the real-time model using PHIL techniques so that the effects of AGFs on the choice feeders could be analyzed.« less
Lamb, Rebecca; Ambler, Carrie A
2013-01-01
Primary human epidermal stem cells isolated from skin tissues and subsequently expanded in tissue culture are used for human therapeutic use to reconstitute skin on patients and to generate artificial skin in culture for academic and commercial research. Classically, epidermal cells, known as keratinocytes, required fibroblast feeder support and serum-containing media for serial propagation. In alignment with global efforts to remove potential animal contaminants, many serum-free, feeder-free culture methods have been developed that support derivation and growth of these cells in 2-dimensional culture. Here we show that keratinocytes grown continually in serum-free and feeder-free conditions were unable to form into a stratified, mature epidermis in a skin equivalent model. This is not due to loss of cell potential as keratinocytes propagated in serum-free, feeder-free conditions retain their ability to form stratified epidermis when re-introduced to classic serum-containing media. Extracellular calcium supplementation failed to improve epidermis development. In contrast, the addition of serum to commercial, growth media developed for serum-free expansion of keratinocytes facilitated 3-dimensional stratification in our skin equivalent model. Moreover, the addition of heat-inactivated serum improved the epidermis structure and thickness, suggesting that serum contains factors that both aid and inhibit stratification.
Lamb, Rebecca; Ambler, Carrie A.
2013-01-01
Primary human epidermal stem cells isolated from skin tissues and subsequently expanded in tissue culture are used for human therapeutic use to reconstitute skin on patients and to generate artificial skin in culture for academic and commercial research. Classically, epidermal cells, known as keratinocytes, required fibroblast feeder support and serum-containing media for serial propagation. In alignment with global efforts to remove potential animal contaminants, many serum-free, feeder-free culture methods have been developed that support derivation and growth of these cells in 2-dimensional culture. Here we show that keratinocytes grown continually in serum-free and feeder-free conditions were unable to form into a stratified, mature epidermis in a skin equivalent model. This is not due to loss of cell potential as keratinocytes propagated in serum-free, feeder-free conditions retain their ability to form stratified epidermis when re-introduced to classic serum-containing media. Extracellular calcium supplementation failed to improve epidermis development. In contrast, the addition of serum to commercial, growth media developed for serum-free expansion of keratinocytes facilitated 3-dimensional stratification in our skin equivalent model. Moreover, the addition of heat-inactivated serum improved the epidermis structure and thickness, suggesting that serum contains factors that both aid and inhibit stratification. PMID:23326335
Nakajima, Ryota; Takeda, Shizu
2014-01-01
The use of murine 3T3 feeder cells needs to be avoided when fabricating corneal epithelial cell sheets for use in treating ocular surface diseases. However, the expression level of the epithelial stem/progenitor cell marker, p63, is down-regulated in feeder-free culture systems. In this study, in order to fabricate corneal epithelial cell sheets that maintain colony-forming cells without using any feeder cells, we investigated the use of an oxygen-controlled method that was developed previously to fabricate cell sheets efficiently. Rabbit limbal epithelial cells were cultured under hypoxia (1-10% O2) and under normoxia during stratification after reaching confluence. Multilayered corneal epithelial cell sheets were fabricated using an oxygen-controlled method, and immunofluorescence analysis showed that cytokeratin 3 and p63 was expressed in appropriate localization in the cell sheets. The colony-forming efficiency of the cell sheets fabricated by the oxygen-controlled method without feeder cells was significantly higher than that of cell sheets fabricated under 20% O2 without feeder cells. These results indicate that the oxygen-controlled method has the potential to achieve a feeder-free culture system for fabricating corneal epithelial cell sheets for corneal regeneration. Copyright © 2013 Elsevier Ltd. All rights reserved.
2007-06-01
Pharmacology and Toxicology , Virginia Commonwealth University, Richmond, VA 2002-present Member, Molecular Biology and Genetics Program, Virginia...Studying Telomeres and Telomerase. Zebrafish , 1:349-355. Jones,K.R., L.W.Elmore, L.Povirk, S.E.Holt, and D.A.Gewirtz. 2005. Reciprocal regulation... Zebrafish Blastula Cell Line on Rainbow Trout Stromal Cells and Subsequent Development under Feeder-Free Conditions into a Cell Line, ZEB2J. Zebrafish 5: 49
Zhang, Kehua; Cai, Zhe; Li, Yang; Shu, Jun; Pan, Lin; Wan, Fang; Li, Hong; Huang, Xiaojie; He, Chun; Liu, Yanqiu; Cui, Xiaohui; Xu, Yang; Gao, Yan; Wu, Liqun; Cao, Shanxia; Li, Lingsong
2011-08-01
Human embryonic stem (ES) cells are usually maintained in the undifferentiated state by culturing on feeder cells layers of mouse embryonic fibroblasts (MEFs). However, MEFs are not suitable to support human ES cells used for clinical purpose because of risk of zoonosis from animal cells. Therefore, human tissue-based feeder layers need to be developed for human ES cells for clinical purpose. Hereof we report that human amniotic mesenchymal cells (hAMCs) could act as feeder cells for human ES cells, because they are easily obtained and relatively exempt from ethical problem. Like MEFs, hAMCs could act as feeder cells for human ES cells to grow well on. The self-renewal rate of human ES cells cultured on hAMCs feeders was higher than that on MEFs and human amniotic epithelial cells determined by measurement of colonial diameters and growth curve as well as cell cycle analysis. Both immunofluorescence staining and immunoblotting showed that human ES cells cultured on hAMCs expressed stem cell markers such as Oct-3/4, Sox2, and NANOG. Verified by embryoid body formation in vitro and teratoma formation in vivo, we found out that after 20 passages of culture, human ES cells grown on hAMCs feeders could still retain the potency of differentiating into three germ layers. Taken together, our data suggested hAMCs may be safe feeder cells to sustain the propagation of human ES cells in undifferentiated state for future therapeutic use.
System Operations Studies : Feeder System Model. User's Manual.
DOT National Transportation Integrated Search
1982-11-01
The Feeder System Model (FSM) is one of the analytic models included in the System Operations Studies (SOS) software package developed for urban transit systems analysis. The objective of the model is to assign a proportion of the zone-to-zone travel...
NASA Astrophysics Data System (ADS)
Cugier, Philippe; Struski, Caroline; Blanchard, Michel; Mazurié, Joseph; Pouvreau, Stéphane; Olivier, Frédéric; Trigui, Jihane R.; Thiébaut, Eric
2010-07-01
The macrobenthic community of Mont Saint Michel Bay (English Channel, France) is mainly dominated by filter feeders, including cultivated species (oysters and mussels). An ecological model of the bay was developed, coupling a 2D hydro-sedimentary model and two biological models for primary production and filter-feeder filtration. The filter-feeder model includes three cultivated species ( Mytilus edulis, Crassostrea gigas and Ostrea edulis), one invasive species ( Crepidula fornicata) and eight wild native species ( Abra alba, Cerastoderma edule, Glycymeris glycymeris, Lanice conchilega, Macoma balthica, Paphia rhomboides, Sabellaria alveolata, andSpisula ovalis). For cultivated and invasive species, the production of biodeposits was computed to assess their role in restimulating primary production. Chlorophyll a concentrations appeared to be strongly controlled by the filter feeders. When the pressure of each benthic compartment on phytoplankton was estimated separately wild species and the invasive slipper limpet C.fornicata were shown to be key elements in the control of primary production. Conversely, the role of cultivated species, particularly oysters, was weaker. Feedback due to the mineralization of biodeposits also appears to be crucial to fully evaluate the role of filter feeders in primary production.
Analysis of Feeder Bus Network Design and Scheduling Problems
Almasi, Mohammad Hadi; Karim, Mohamed Rehan
2014-01-01
A growing concern for public transit is its inability to shift passenger's mode from private to public transport. In order to overcome this problem, a more developed feeder bus network and matched schedules will play important roles. The present paper aims to review some of the studies performed on Feeder Bus Network Design and Scheduling Problem (FNDSP) based on three distinctive parts of the FNDSP setup, namely, problem description, problem characteristics, and solution approaches. The problems consist of different subproblems including data preparation, feeder bus network design, route generation, and feeder bus scheduling. Subsequently, descriptive analysis and classification of previous works are presented to highlight the main characteristics and solution methods. Finally, some of the issues and trends for future research are identified. This paper is targeted at dealing with the FNDSP to exhibit strategic and tactical goals and also contributes to the unification of the field which might be a useful complement to the few existing reviews. PMID:24526890
Assessment of benthic changes during 20 years of monitoring the Mexican Salina Cruz Bay.
González-Macías, C; Schifter, I; Lluch-Cota, D B; Méndez-Rodríguez, L; Hernández-Vázquez, S
2009-02-01
In this work a non-parametric multivariate analysis was used to assess the impact of metals and organic compounds in the macro infaunal component of the mollusks benthic community using surface sediment data from several monitoring programs collected over 20 years in Salina Cruz Bay, Mexico. The data for benthic mollusks community characteristics (richness, abundance and diversity) were linked to multivariate environmental patterns, using the Alternating Conditional Expectations method to correlate the biological measurements of the mollusk community with the physicochemical properties of water and sediments. Mollusks community variation is related to environmental characteristics as well as lead content. Surface deposit feeders are increasing their relative density, while subsurface deposit feeders are decreasing with respect to time, these last are expected to be more related with sediment and more affected then by its quality. However gastropods with predatory carnivore as well as chemosymbiotic deposit feeder bivalves have maintained their relative densities along time.
Modern Grid Initiative Distribution Taxonomy Final Report
DOE Office of Scientific and Technical Information (OSTI.GOV)
Schneider, Kevin P.; Chen, Yousu; Chassin, David P.
2008-11-01
This is the final report for the development of a toxonomy of prototypical electrical distribution feeders. Two of the primary goals of the Department of Energy's (DOE) Modern Grid Initiative (MGI) are 'to accelerate the modernization of our nation's electricity grid' and to 'support demonstrations of systems of key technologies that can serve as the foundation for an integrated, modern power grid'. A key component to the realization of these goals is the effective implementation of new, as well as existing, 'smart grid technologies'. Possibly the largest barrier that has been identified in the deployment of smart grid technologies ismore » the inability to evaluate how their deployment will affect the electricity infrastructure, both locally and on a regional scale. The inability to evaluate the impacts of these technologies is primarily due to the lack of detailed electrical distribution feeder information. While detailed distribution feeder information does reside with the various distribution utilities, there is no central repository of information that can be openly accessed. The role of Pacific Northwest National Laboratory (PNNL) in the MGI for FY08 was to collect distribution feeder models, in the SynerGEE{reg_sign} format, from electric utilities around the nation so that they could be analyzed to identify regional differences in feeder design and operation. Based on this analysis PNNL developed a taxonomy of 24 prototypical feeder models in the GridLAB-D simulations environment that contain the fundamental characteristics of non-urban core, radial distribution feeders from the various regions of the U.S. Weighting factors for these feeders are also presented so that they can be used to generate a representative sample for various regions within the United States. The final product presented in this report is a toolset that enables the evaluation of new smart grid technologies, with the ability to aggregate their effects to regional and national levels. The distribution feeder models presented in this report are based on actual utility models but do not contain any proprietary or system specific information. As a result, the models discussed in this report can be openly distributed to industry, academia, or any interested entity, in order to facilitate the ability to evaluate smart grid technologies.« less
A Brief Study of Cafeteria Facilities and Operations, with Recommendations for Implementation.
ERIC Educational Resources Information Center
Okamura, James T.
The facilities and operations of the school lunch program in the public schools of Hawaii are reviewed. Several types of school lunch programs are described including--(1) traditional school lunch programs, (2) kitchen and classroom dining, (3) central and decentralized dining, (4) home school-feeder school system, (5) central kitchen, and (6) the…
DOT National Transportation Integrated Search
1975-03-01
parametric variation of demand density was used to compare service level and cost of two alternative systems for providing low density feeder service. Supply models for fixed route and flexible route service were developed and applied to determine ra...
Novel Methods to Determine Feeder Locational PV Hosting Capacity and PV Impact Signatures
DOE Office of Scientific and Technical Information (OSTI.GOV)
Reno, Matthew J.; Coogan, Kyle; Seuss, John
Often PV hosting capacity analysis is performed for a limited number of distribution feeders. For medium - voltage distribution feeders, previous results generally analyze less than 20 feeders, and then the results are extrapolated out to similar types of feeders. Previous hosting capacity research has often focused on determining a single value for the hosting capacity for the entire feeder, whereas this research expands previous hosting capacity work to investigate all the regions of the feeder that may allow many different hosting capacity values wit h an idea called locational hosting capacity (LHC)to determine the largest PV size that canmore » be interconnected at different locations (buses) on the study feeders. This report discusses novel methods for analyzing PV interconnections with advanced simulati on methods. The focus is feeder and location - specific impacts of PV that determine the locational PV hosting capacity. Feeder PV impact signature are used to more precisely determine the local maximum hosting capacity of individual areas of the feeder. T he feeder signature provides improved interconnection screening with certain zones that show the risk of impact to the distribution feeder from PV interconnections.« less
IEEE 342 Node Low Voltage Networked Test System
DOE Office of Scientific and Technical Information (OSTI.GOV)
Schneider, Kevin P.; Phanivong, Phillippe K.; Lacroix, Jean-Sebastian
The IEEE Distribution Test Feeders provide a benchmark for new algorithms to the distribution analyses community. The low voltage network test feeder represents a moderate size urban system that is unbalanced and highly networked. This is the first distribution test feeder developed by the IEEE that contains unbalanced networked components. The 342 node Low Voltage Networked Test System includes many elements that may be found in a networked system: multiple 13.2kV primary feeders, network protectors, a 120/208V grid network, and multiple 277/480V spot networks. This paper presents a brief review of the history of low voltage networks and how theymore » evolved into the modern systems. This paper will then present a description of the 342 Node IEEE Low Voltage Network Test System and power flow results.« less
Cost Benefit and Alternatives Analysis of Distribution Systems with Energy Storage Systems: Preprint
DOE Office of Scientific and Technical Information (OSTI.GOV)
Harris, Tom; Nagarajan, Adarsh; Baggu, Murali
This paper explores monetized and non-monetized benefits from storage interconnected to distribution system through use cases illustrating potential applications for energy storage in California's electric utility system. This work supports SDG&E in its efforts to quantify, summarize, and compare the cost and benefit streams related to implementation and operation of energy storage on its distribution feeders. This effort develops the cost benefit and alternatives analysis platform, integrated with QSTS feeder simulation capability, and analyzed use cases to explore the cost-benefit of implementation and operation of energy storage for feeder support and market participation.
Blood feeding behavior of the stable fly
USDA-ARS?s Scientific Manuscript database
Stable fly is a fly that looks similar to a house fly but both sexes are blood feeders. Blood is required for successful fertilization and development of eggs. Bites are painful but there is usually no pain after the fly stops feeding. The stable fly is a persistent feeder and will continue trying t...
Round-bale feeder design affects hay waste and economics during horse feeding.
Martinson, K; Wilson, J; Cleary, K; Lazarus, W; Thomas, W; Hathaway, M
2012-03-01
Many horse owners find round bales convenient, less labor intensive, and more affordable than other hay types, but report an inability to control horse BW gain and excessive hay waste. The objectives were to compare hay waste, hay intake, and payback of 9 round-bale feeders and a no-feeder control when used during horse feeding. Nine round-bale feeders were tested: Cinch Net, Cone, Covered Cradle, Hayhut, Hay Sleigh, Ring, Tombstone, Tombstone Saver, and Waste Less. Each feeder design was placed on the ground in a dirt paddock. Five groups of 5 horses were fed in rotation for a 4-d period with each feeder. Every fourth day, groups were rotated among paddocks and a new round bale was placed in each feeder. In the 5 paddocks used, 5 feeders were installed for d 1 through 20, and the remaining 4 feeders and no-feeder control were installed for d 21 through 40. Groups of horses were sequentially assigned to feeders using two 5 × 5 Latin squares, the first for d 1 through 20, the second for d 21 through 40. Horse groups of similar age, BW, breed, and sex were formed from 25 Quarter Horse and Thoroughbred geldings and open mares (means: 11 yr; 541 kg of BW). Hay on the ground surrounding the feeder was collected daily, dried, and weighed. The total amount of hay removed around each feeder for a 4-d period was considered waste. Dry matter intake was estimated as the difference between hay disappearance and waste. Number of months for the reduction in waste to repay feeder cost (payback) were calculated using hay valued at $110/t, and improved feeder efficiency over the control. Feeder design did not affect hay intake (P > 0.05); all feeders resulted in an estimated hay intake of 2.0 to 2.4% BW; the no-feeder control resulted in a reduced intake of 1.3% BW (P = 0.001). Mean percentage of hay waste differed among feeders (P < 0.001): Waste Less, 5%; Cinch Net, 6%; Hayhut, 9%; Covered Cradle, 11%; Tombstone Saver, 13%; Tombstone, Cone, and Ring, 19%; Hay Sleigh, 33%; and no-feeder control, 57%. Feeder design also affected payback (P < 0.01). The Cinch Net paid for itself in less than 1 mo; Tombstone and Ring, 2 mo; Hayhut and Tombstone Saver, 4 mo; Hay Sleigh, 5 mo; Waste Less, 8 mo; Cone, 9 mo; and Covered Cradle, 20 mo. Round-bale feeder design affected hay waste and payback, but not estimated hay intake or BW change during horse feeding.
Bergstrom, J R; Nelssen, J L; Edwards, L N; Tokach, M D; Dritz, S S; Goodband, R D; DeRouchey, J M
2012-12-01
Our objectives were to compare a conventional dry (5-space, 152.4-cm-wide) and a wet-dry (double-sided, each side = 38.1-cm-wide single space) feeder and to determine if changing the source of water to a location separate from a wet-dry feeder would result in improved G:F and carcass characteristics. Water supply to the wet-dry feeder was shut off and the cup waterer was turned on in 8 pens at 8 (d 69) or 4 (d 97) wk prior to harvest. For the remaining 8 wet-dry feeder pens, the feeder provided the sole water source for the entire experiment. A total of 1,296 pigs (PIC, 337 × 1050; initially 19.4 kg BW) were used, with 27 pigs/pen (14 barrows and 13 gilts) and 24 pens/feeder design. From d 0 to 69, pigs fed with the wet-dry feeder had increased (P < 0.05) ADG, ADFI, G:F, and d 69 BW compared with those using the conventional dry feeder. Overall (d 0 to 124), pigs using fed with the water source in the wet-dry feeder the entire time had greater (P < 0.05) ADG, ADFI, final BW, and HCW the other treatments. The overall G:F was not different (P > 0.05) among pigs fed with the different feeder treatments. Pigs fed with the wet-dry feeder where water source was changed at 4 wk before harvest had greater (P < 0.05) ADG than pigs that used a conventional dry feeder. Pigs where the water source was changed at 4 wk had greater (P < 0.05) ADFI than those were the water source was changed 8 wk prior to harvest, and for pigs fed with the conventional dry feeder ADFI was intermediate. Back fat depth of pigs where the water source was changed at 8 wk before harvest was reduced (P < 0.05) compared with all other treatments and LM depth was greater (P < 0.05) than that of pigs using a conventional dry feeder and where the water source was changed at 4 week before harvest. Pigs fed using the wet-dry feeder visited the feeder less frequently (P < 0.05) and spent less total time at the feeder (P < 0.05) than those fed with the conventional dry feeder. The differences in feeding patterns remained even after the access to water was removed from the wet-dry feeder, with no change in the amount of aggressive behavior observed at the feeder. Pigs fed with a wet-dry feeder had an increased growth rate compared with those fed with a conventional dry feeder. Although measures of carcass leanness were improved by changing the location of the water, removing the water from the feeder also eliminated any net improvement in BW from using a wet-dry feeder.
95. VIEW OF ZINC FEEDER FROM SOUTHEAST. NOTE FEEDER CONE ...
95. VIEW OF ZINC FEEDER FROM SOUTHEAST. NOTE FEEDER CONE AND PIPING FROM VACUUM RECEIVER ON LEFT. PRECIPITATE PUMP MOTOR MOUNT VISIBLE BELOW FEEDER STAIRS, PUMP AND MOTOR MISSING. SUMPS ARE LOCATED UNDER THIS FLOOR, WITH ACCESS TO HATCH TO THE RIGHT OF FEEDER STAIR. - Bald Mountain Gold Mill, Nevada Gulch at head of False Bottom Creek, Lead, Lawrence County, SD
Hygiene at winter bird feeders in a southwestern Ontario city.
Prescott, J F; Hunter, D B; Campbell, G D
2000-01-01
To further understand the source of the epidemic of salmonellosis in some species of birds using bird feeders in southern Ontario in the winter of 1997-1998, 124 bird feeder stations were examined for their state of hygiene and for Salmonella on 5 occasions during the winter of 1999 in a city of 100,000 people in southwestern Ontario. No Salmonella were isolated from feed contaminated with feces recovered from the feeders. Squirrel-proof feeders were significantly less contaminated with feces than were other feeder types (hopper, platform, silo), which did not differ significantly in their hygiene scores. Contamination of squirrel-proof feeders increased significantly through the course of the study, but other feeder types showed no significant change. Hygiene was poorer if feeders were maintained equally by both male and female household members, particularly as they grew older, but no age or gender effect was observed if only one person was largely responsible for maintaining the feeders. We concluded that winter bird feeder stations in a southern Ontario city were not contaminated with Salmonella but that bird feeder stations could be designed better to reduce fecal contamination of feed. PMID:10992987
Technologies for Energy from Biomass by Direct Combustion, Gasification, and Liquefaction.
1981-05-01
1980 1982 1984 Development Alberta Industrial Dev. X American Fyr. Feeder X Andco, Inc. X Applied Engineering Co., Inc. X Biomass Corp. X Bio-Solar x...Feeder ANDCO, Inc. Applied Engineering Company Biomass Corporation Bio-Solar Research and Development Corporation Combustion Power Company, Inc. Davy...Andco. Inc. X Applied Engineering Co., Inc. X Biomass Corp. X , Big-Solar .X I Combustion Power .. XI Davy Powergas X j Dekalb Acresearch, Inc.- x Duvant
Intercity Bus Feeder Project Program Analysis
DOT National Transportation Integrated Search
1990-09-01
Following the passage of the Bus Regualtory Reform Act of 1982 (BRRA), intercity : carriers used their increased regulatory flexibility to discontinue many : underutilized rural and small city services. This was understandable, in light : of the comp...
Culture of porcine hepatocytes or bile duct epithelial cells by inductive serum-free media
USDA-ARS?s Scientific Manuscript database
A serum-free, feeder-cell-dependent, selective culture system for the long-term culture of porcine hepatocytes or cholangiocytes was developed. Liver cells were isolated from 1 wk old pigs or young adult pigs (25 and 63 kg live weight) and were placed in primary culture on feeder-cell layers of mit...
An automatic 14-day paste diet feeder for animals
NASA Technical Reports Server (NTRS)
Vasques, Marilyn; Mulenburg, Jerry; Gundo, Dan; Griffith, Jon
1994-01-01
During a centrifuge experiment, any interruption that requires stopping the centrifuge may influence the results. Centrifuges often must be stopped for animal maintenance (food, water and waste removal), especially in cases of timed feedings. To eliminate the need for stopping the centrifuge while still providing timed feeding, an automatic paste diet feeder was developed. The feeder is based on a constant volume concept and can deliver a predetermined amount of paste diet at specified time intervals. This unit was supported by water delivery and waste collection systems. The entire system performed reliably and maintained the animals well for a continuous centrifugation experiment of 14 days.
Intelligent Distribution Voltage Control with Distributed Generation =
NASA Astrophysics Data System (ADS)
Castro Mendieta, Jose
In this thesis, three methods for the optimal participation of the reactive power of distributed generations (DGs) in unbalanced distributed network have been proposed, developed, and tested. These new methods were developed with the objectives of maintain voltage within permissible limits and reduce losses. The first method proposes an optimal participation of reactive power of all devices available in the network. The propose approach is validated by comparing the results with other methods reported in the literature. The proposed method was implemented using Simulink of Matlab and OpenDSS. Optimization techniques and the presentation of results are from Matlab. The co-simulation of Electric Power Research Institute's (EPRI) OpenDSS program solves a three-phase optimal power flow problem in the unbalanced IEEE 13 and 34-node test feeders. The results from this work showed a better loss reduction compared to the Coordinated Voltage Control (CVC) method. The second method aims to minimize the voltage variation on the pilot bus on distribution network using DGs. It uses Pareto and Fuzzy-PID logic to reduce the voltage variation. Results indicate that the proposed method reduces the voltage variation more than the other methods. Simulink of Matlab and OpenDSS is used in the development of the proposed approach. The performance of the method is evaluated on IEEE 13-node test feeder with one and three DGs. Variables and unbalanced loads are used, based on real consumption data, over a time window of 48 hours. The third method aims to minimize the reactive losses using DGs on distribution networks. This method analyzes the problem using the IEEE 13-node test feeder with three different loads and the IEEE 123-node test feeder with four DGs. The DGs can be fixed or variables. Results indicate that integration of DGs to optimize the reactive power of the network helps to maintain the voltage within the allowed limits and to reduce the reactive power losses. The thesis is presented in the form of the three articles. The first article is published in the journal Electrical Power and Energy System, the second is published in the international journal Energies and the third was submitted to the journal Electrical Power and Energy System. Two other articles have been published in conferences with reviewing committee. This work is based on six chapters, which are detailed in the various sections of the thesis.
RF model of the distribution system as a communication channel, phase 2. Volume 3: Appendices
NASA Technical Reports Server (NTRS)
Rustay, R. C.; Gajjar, J. T.; Rankin, R. W.; Wentz, R. C.; Wooding, R.
1982-01-01
Program documentation concerning the design, implementation, and verification of a computerized model for predicting the steady-state sinusoidal response of radial configured distribution feeders is presented in these appendices.
NASA Astrophysics Data System (ADS)
Abramov, E. Y.; Sopov, V. I.
2017-10-01
In a given research using the example of traction network area with high asymmetry of power supply parameters, the sequence of comparative assessment of power losses in DC traction network with parallel and traditional separated operating modes of traction substation feeders was shown. Experimental measurements were carried out under these modes of operation. The calculation data results based on statistic processing showed the power losses decrease in contact network and the increase in feeders. The changes proved to be critical ones and this demonstrates the significance of potential effects when converting traction network areas into parallel feeder operation. An analytical method of calculation the average power losses for different feed schemes of the traction network was developed. On its basis, the dependences of the relative losses were obtained by varying the difference in feeder voltages. The calculation results showed unreasonableness transition to a two-sided feed scheme for the considered traction network area. A larger reduction in the total power loss can be obtained with a smaller difference of the feeders’ resistance and / or a more symmetrical sectioning scheme of contact network.
Chugh, Rishi Man; Chaturvedi, Madhusudan; Yerneni, Lakshmana Kumar
2016-01-01
Growth-arrested feeder cells following Mitomycin C treatment are instrumental in stem cell culture allowing development of regenerative strategies and alternatives to animal testing in drug discovery. The concentration of Mitomycin C and feeder cell type was described to affect feeder performance but the criticality of feeder cell exposure density was not addressed. We hypothesize that the exposure cell density influences the effectiveness of Mitomycin C in an arithmetic manner. Three different exposure cell densities of Swiss 3T3 fibroblasts were treated with a range of Mitomycin C concentrations for 2h. The cells were replaced and the viable cells counted on 3, 6, 9, 12 and 20days. The cell extinctions were compared with doses per cell which were derived by dividing the product of concentration and volume of Mitomycin C solution with exposure cell number. The periodic post-treatment feeder cell extinctions were not just dependent on Mitomycin C concentration but also on dose per cell. Analysis of linearity between viable cell number and Mitomycin C dose per cell derived from the concentrations of 3 to 10μg/ml revealed four distinct categories of growth-arrest. Confluent cultures exposed to low concentration showed growth-arrest failure. The in vitro cell density titration can facilitate prediction of a compound's operational in vivo dosing. For containing the growth arrest failure, an arithmetic volume derivation strategy is proposed by fixing the exposure density to a safe limit. The feeder extinction characteristics are critical for streamlining the stem cell based pharmacological and toxicological assays. Copyright © 2016 Elsevier Inc. All rights reserved.
Colour preferences of UK garden birds at supplementary seed feeders.
Rothery, Luke; Scott, Graham W; Morrell, Lesley J
2017-01-01
Supplementary feeding of garden birds generally has benefits for both bird populations and human wellbeing. Birds have excellent colour vision, and show preferences for food items of particular colours, but research into colour preferences associated with artificial feeders is limited to hummingbirds. Here, we investigated the colour preferences of common UK garden birds foraging at seed-dispensing artificial feeders containing identical food. We presented birds simultaneously with an array of eight differently coloured feeders, and recorded the number of visits made to each colour over 370 30-minute observation periods in the winter of 2014/15. In addition, we surveyed visitors to a garden centre and science festival to determine the colour preferences of likely purchasers of seed feeders. Our results suggest that silver and green feeders were visited by higher numbers of individuals of several common garden bird species, while red and yellow feeders received fewer visits. In contrast, people preferred red, yellow, blue and green feeders. We suggest that green feeders may be simultaneously marketable and attractive to foraging birds.
Schlienger, M. Eric; Schmale, David T.; Oliver, Michael S.
2001-07-10
A new class of precision powder feeders is disclosed. These feeders provide a precision flow of a wide range of powdered materials, while remaining robust against jamming or damage. These feeders can be precisely controlled by feedback mechanisms.
Technologies to Increase PV Hosting Capacity in Distribution Feeders: Preprint
DOE Office of Scientific and Technical Information (OSTI.GOV)
Ding, Fei; Mather, Barry; Gotseff, Peter
This paper studies the distributed photovoltaic (PV) hosting capacity in distribution feeders by using the stochastic analysis approach. Multiple scenario simulations are conducted to analyze several factors that affect PV hosting capacity, including the existence of voltage regulator, PV location, the power factor of PV inverter and Volt/VAR control. Based on the conclusions obtained from simulation results, three approaches are then proposed to increase distributed PV hosting capacity, which can be formulated as the optimization problem to obtain the optimal solution. All technologies investigated in this paper utilize only existing assets in the feeder and therefore are implementable for amore » low cost. Additionally, the tool developed for these studies is described.« less
Technologies to Increase PV Hosting Capacity in Distribution Feeders
DOE Office of Scientific and Technical Information (OSTI.GOV)
Ding, Fei; Mather, Barry; Gotseff, Peter
This paper studies the distributed photovoltaic (PV) hosting capacity in distribution feeders by using the stochastic analysis approach. Multiple scenario simulations are conducted to analyze several factors that affect PV hosting capacity, including the existence of voltage regulator, PV location, the power factor of PV inverter and Volt/VAR control. Based on the conclusions obtained from simulation results, three approaches are then proposed to increase distributed PV hosting capacity, which can be formulated as the optimization problem to obtain the optimal solution. All technologies investigated in this paper utilize only existing assets in the feeder and therefore are implementable for amore » low cost. Additionally, the tool developed for these studies is described.« less
Averós, X; Brossard, L; Dourmad, J Y; de Greef, K H; Edwards, S A; Meunier-Salaün, M C
2012-08-01
A meta-analysis, using information from 45 experiments on growing-finishing pigs published in 39 manuscripts, was carried out to determine the simultaneous effects of the physical environment (space allowance, group size, flooring conditions, temperature, presence of enrichment), pig traits (initial body weight (BW) for each studied time interval, sex, genetics), feeder characteristics (water provision within the feeder, feeder design (individual/collective), feeder places/pig, presence of feeder protection) and feed characteristics (feed allowance (ad libitum/restricted), net energy content, crude protein (CP) content), as well as their potential interactions, on the feeding behaviour and performance of growing-finishing pigs. The detrimental effect of low temperature on performance was particularly evident for restricted-fed pigs (P < 0.05). At reduced feeder space allowance, a reduction in the percentage of time spent eating was predicted when increasing initial BW, whereas the opposite was predicted for larger feeder space allowances (P < 0.001). The reduction in visit duration to the feeder in higher BW groups became gradually more important with increasing feeder space allowance (P < 0.01), whereas the increase in the ingestion rate and average daily feed intake (ADFI) with increasing initial BW became smaller with increasing feeder space (P < 0.05). The model predicted a reduction in feed conversion ratio (FCR) with increasing group size (P < 0.05) and floor space allowance (P < 0.01) and on solid floors with or without bedding (P < 0.05). In comparison with other feeders, wet/dry feeders were associated with more frequent but shorter feeder visits (P < 0.05), higher ingestion rates (P < 0.001) and higher ADFI (P < 0.10). The use of protection within individual feeders increased the time spent feeding (P < 0.001), reduced the number of visits per day (P < 0.01), the ingestion rate (P < 0.001) and FCR (P < 0.01) in comparison with other feeder types. Sex modulated the effect of the number of feeder places/pig on FCR (P < 0.05), with a gradual reduction of FCR in entire males and females when increasing feeder space allowance. Genetics tended to modulate the effect of diets' CP content on FCR (P < 0.10). Overall, these results may contribute to the improvement of the welfare and performance of growing-finishing pigs by a better knowledge of the influence of the rearing environment and may help optimize the feeding strategies in current production systems.
Code of Federal Regulations, 2011 CFR
2011-07-01
... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Insulation of trolley wires, trolley feeder wires and bare signal wires; guarding of trolley wires and trolley feeder wires. 77.1802 Section 77.1802... Wires and Trolley Feeder Wires § 77.1802 Insulation of trolley wires, trolley feeder wires and bare...
Code of Federal Regulations, 2010 CFR
2010-07-01
... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Insulation of trolley wires, trolley feeder wires and bare signal wires; guarding of trolley wires and trolley feeder wires. 77.1802 Section 77.1802... Wires and Trolley Feeder Wires § 77.1802 Insulation of trolley wires, trolley feeder wires and bare...
Large area sheet task. Advanced dendritic web growth development. [silicon films
NASA Technical Reports Server (NTRS)
Duncan, C. S.; Seidensticker, R. G.; Mchugh, J. P.; Hopkins, R. H.; Meier, D.; Frantti, E.; Schruben, J.
1981-01-01
The development of a silicon dendritic web growth machine is discussed. Several refinements to the sensing and control equipment for melt replenishment during web growth are described and several areas for cost reduction in the components of the prototype automated web growth furnace are identified. A circuit designed to eliminate the sensitivity of the detector signal to the intensity of the reflected laser beam used to measure melt level is also described. A variable speed motor for the silicon feeder is discussed which allows pellet feeding to be accomplished at a rate programmed to match exactly the silicon removed by web growth.
Feeder density enhances house finch disease transmission in experimental epidemics.
Moyers, Sahnzi C; Adelman, James S; Farine, Damien R; Thomason, Courtney A; Hawley, Dana M
2018-05-05
Anthropogenic food provisioning of wildlife can alter the frequency of contacts among hosts and between hosts and environmental sources of pathogens. Despite the popularity of garden bird feeding, few studies have addressed how feeders influence host contact rates and disease dynamics. We experimentally manipulated feeder density in replicate aviaries containing captive, pathogen-naive, groups of house finches ( Haemorhous mexicanus ) and continuously tracked behaviours at feeders using radio-frequency identification devices. We then inoculated one bird per group with Mycoplasma gallisepticum (Mg), a common bacterial pathogen for which feeders are fomites of transmission, and assessed effects of feeder density on house finch behaviour and pathogen transmission. We found that pathogen transmission was significantly higher in groups with the highest density of bird feeders, despite a significantly lower rate of intraspecific aggressive interactions relative to the low feeder density groups. Conversely, among naive group members that never showed signs of disease, we saw significantly higher concentrations of Mg-specific antibodies in low feeder density groups, suggesting that birds in low feeder density treatments had exposure to subclinical doses of Mg. We discuss ways in which the density of garden bird feeders could play an important role in mediating the intensity of Mg epidemics.This article is part of the theme issue 'Anthropogenic resource subsidies and host-parasite dynamics in wildlife'. © 2018 The Author(s).
An in vitro monocyte culture method and establishment of a human monocytic cell line (K63).
Kadoi, Katsuyuki
2011-01-01
A novel method of monocyte culture in vitro was developed. The fraction of monocytes was obtained by density centrifugation of heparinised human venous blood samples. Monocytes were suspended in a modified Rosewell Park Memorial Institute medium (RPMI)-1640 (mRPMI) supplemented with 10% non-inactivated autologous serum added to the feeder cells. An avian cell line was used for feeder cells. Only those monocytes that settled on feeder cells grew rapidly at 37°C-38°C into a formation of clumped masses within two to three days. The cell mass was harvested and subcultures were made without feeder cells. A stable cell line (K63) was established from subcultures using a limited dilution method and cell cloning in microplates. K63 cells were adapted for later growth in the mRPMI medium supplemented with 10% foetal calf serum. The cells were well maintained at over 50th passage levels. This method proved to be applicable for monocyte cultures of animals as well.
DOE Office of Scientific and Technical Information (OSTI.GOV)
Schneider, Kevin P.; Sortomme, Eric; Venkata, S. S.
The increased level of demand that is associated with the restoration of service after an outage, Cold Load Pick-Up (CLPU), can be significantly higher than pre-outage levels, even exceeding the normal distribution feeder peak demand. These high levels of demand can delay restoration efforts and in extreme cases damage equipment. The negative impacts of CLPU can be mitigated with strategies that restore the feeder in sections, minimizing the load current. The challenge for utilities is to manage the current level on critical equipment while minimizing the time to restore service to all customers. Accurately modeling CLPU events is the firstmore » step in developing improved restoration strategies that minimize restoration times. This paper presents a new method for evaluating the magnitude of the CLPU peak, and its duration, using multi-state load models. The use of multi-state load models allows for a more accurate representation of the end-use loads that are present on residential distribution feeders.« less
DOE Office of Scientific and Technical Information (OSTI.GOV)
Baggu, Murali; Giraldez, Julieta; Harris, Tom
In an effort to better understand the impacts of high penetrations of photovoltaic (PV) generators on distribution systems, Arizona Public Service and its partners completed a multi-year project to develop the tools and knowledge base needed to safely and reliably integrate high penetrations of utility- and residential-scale PV. Building upon the APS Community Power Project-Flagstaff Pilot, this project investigates the impact of PV on a representative feeder in northeast Flagstaff. To quantify and catalog the effects of the estimated 1.3 MW of PV that will be installed on the feeder (both smaller units at homes and large, centrally located systems),more » high-speed weather and electrical data acquisition systems and digital 'smart' meters were designed and installed to facilitate monitoring and to build and validate comprehensive, high-resolution models of the distribution system. These models are being developed to analyze the impacts of PV on distribution circuit protection systems (including coordination and anti-islanding), predict voltage regulation and phase balance issues, and develop volt/VAr control schemes. This paper continues from a paper presented at the 2014 IEEE PVSC conference that described feeder model evaluation and high penetration advanced scenario analysis, specifically feeder reconfiguration. This paper presents results from Phase 5 of the project. Specifically, the paper discusses tool automation; interconnection assessment methodology and cost benefit analysis.« less
Colour preferences of UK garden birds at supplementary seed feeders
Rothery, Luke; Scott, Graham W.
2017-01-01
Supplementary feeding of garden birds generally has benefits for both bird populations and human wellbeing. Birds have excellent colour vision, and show preferences for food items of particular colours, but research into colour preferences associated with artificial feeders is limited to hummingbirds. Here, we investigated the colour preferences of common UK garden birds foraging at seed-dispensing artificial feeders containing identical food. We presented birds simultaneously with an array of eight differently coloured feeders, and recorded the number of visits made to each colour over 370 30-minute observation periods in the winter of 2014/15. In addition, we surveyed visitors to a garden centre and science festival to determine the colour preferences of likely purchasers of seed feeders. Our results suggest that silver and green feeders were visited by higher numbers of individuals of several common garden bird species, while red and yellow feeders received fewer visits. In contrast, people preferred red, yellow, blue and green feeders. We suggest that green feeders may be simultaneously marketable and attractive to foraging birds. PMID:28212435
ERIC Educational Resources Information Center
Baginski, Jessie
2010-01-01
Many college campuses across the country have implemented U-Pass transit programs to mitigate transportation costs for students. However, urban university U-pass programs fall short for suburban students who cannot get to the urban metro area without connecting public transportation. As urban universities rely on suburbs as feeder communities,…
Feed intake and behavior of dairy goats when offered an elevated feed bunk.
Neave, Heather W; von Keyserlingk, Marina A G; Weary, Daniel M; Zobel, Gosia
2018-04-01
Goats are browsers and select vegetation at various heights when foraging. On commercial farms, dairy goats are typically fed from low-level feed bunks. The objective of this study was to determine how feed intake and feeding behavior vary when goats are offered feed at variable heights, with the potential of evaluating the benefits of offering an elevated feeder to dairy goats. Thirteen Saanen X dairy goats were housed in a home pen with a lying area of wood shavings, where they were pre-exposed for 24 d to 3 feeder heights designed to result in differences in head height while feeding: floor level (head lowered relative to body), head level (head level relative to body), and elevated level (head and neck angled upward). Nine groups of 3 goats each were randomly selected and housed for 24 h in a test pen identical to the home pen except that it contained 1 of each of the 3 feeder heights. Each feeder contained ad libitum chopped alfalfa silage and a top-dressed corn-based supplement, refreshed twice daily. Refusals from inside and under each feeder were weighed to calculate intake. Feed intake increased with increasing feeder height (mean ± SE; 0.18, 0.29, and 0.34 ± 0.04 kg of DM/goat for floor-level, head-level, and elevated-level feeders, respectively). Total feeding time did not vary with feeder height, but feeding rate tended to be faster at the elevated-level feeder (14.5 ± 2.1 g of DM/min) compared with head-level (9.2 ± 2.3 g of DM/min) and floor-level (8.9 ± 2.1 g of DM/min) feeders. Goats visited the floor-level feeder (36.4 ± 8.4 visits/goat) less than the head-level (79.4 ± 8.4 visits/goat) and elevated-level (74.8 ± 8.4 visits/goat) feeders. The number of displacements per minute of feeding time (physical removal of another goat from the feeding place) was greater at the elevated-level feeder (0.46 ± 0.06 displacements/min) compared with the floor-level feeder (0.23 ± 0.06 displacements/min) and tended to differ from the head-level feeder (0.27 ± 0.06 displacements/min). We conclude that goats eat more from an elevated feeder and compete more to access this feeder. Copyright © 2018 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.
Morita, Maresuke; Fujita, Naoki; Abe, Momoko; Hayashimoto, Koji; Nakagawa, Takayuki; Nishimura, Ryohei; Tsuzuki, Keiko
2018-06-01
We have previously reported characteristics of canine corneal epithelial cells in vitro and found that canine corneal epithelial cells could maintain their proliferative capacity even after continuous culture without the use of feeder cells and growth promoting additives. The objective of this study was to elucidate proliferative characteristics of canine corneal epithelial cells independent of feeder cells and growth promoting additives, with the aim of developing a spontaneously derived corneal epithelial cell line. Canine and rabbit corneal epithelial cells were harvested from the limbus and cultured with, or without, feeder cells and growth promoting additives, and both were passaged continuously until growth arrest. Canine corneal epithelial cells could proliferate independently, and could be passaged more times than rabbit cells. A canine corneal epithelial cell line, cCEpi, which could be passaged more than 100 times without using feeder cells and growth promoting additives, was established. cCEpi cells maintained a cell morphology close to the primary culture and expressed p63, cytokeratin 15 (K15), and K3. Although changes in colony morphology, shortening of the population doubling time and a heteroploid karyotype were observed, cCEpi was not tumorigenic. Stratified cell sheets cultured from cCEpi were morphologically and immunohistologically similar to sheets cultivated from early passage cells. In conclusion, canine corneal epithelial cells can proliferate independent of feeder cells and growth promoting additives. cCEpi maintains properties similar to normal corneal epithelial cells and could be a useful source for studies in cellular biology and for developing novel therapies. Copyright © 2018 Elsevier Ltd. All rights reserved.
35. INTERIOR VIEW, SAME AS ABOVE WITH THE FEEDER ROD ...
35. INTERIOR VIEW, SAME AS ABOVE WITH THE FEEDER ROD INSERTED INTO THE MACHINE; NOTE THE WOOD FEEDER ROD AND FEEDER ROD REST ON THE BACK OF THE STOOL - LaBelle Iron Works, Thirtieth & Wood Streets, Wheeling, Ohio County, WV
Voltage Impacts of Utility-Scale Distributed Wind
DOE Office of Scientific and Technical Information (OSTI.GOV)
Allen, A.
2014-09-01
Although most utility-scale wind turbines in the United States are added at the transmission level in large wind power plants, distributed wind power offers an alternative that could increase the overall wind power penetration without the need for additional transmission. This report examines the distribution feeder-level voltage issues that can arise when adding utility-scale wind turbines to the distribution system. Four of the Pacific Northwest National Laboratory taxonomy feeders were examined in detail to study the voltage issues associated with adding wind turbines at different distances from the sub-station. General rules relating feeder resistance up to the point of turbinemore » interconnection to the expected maximum voltage change levels were developed. Additional analysis examined line and transformer overvoltage conditions.« less
41 CFR 109-43.4701 - Performance reports.
Code of Federal Regulations, 2012 CFR
2012-01-01
... Science Education Programs, using the following format, will include data for all personal property... elementary and secondary schools and non-profit organizations under initiatives to support science and mathematics education. (2) Field office feeder reports shall not include data for contractor inventory which...
41 CFR 109-43.4701 - Performance reports.
Code of Federal Regulations, 2010 CFR
2010-07-01
... Science Education Programs, using the following format, will include data for all personal property... elementary and secondary schools and non-profit organizations under initiatives to support science and mathematics education. (2) Field office feeder reports shall not include data for contractor inventory which...
41 CFR 109-43.4701 - Performance reports.
Code of Federal Regulations, 2014 CFR
2014-01-01
... Science Education Programs, using the following format, will include data for all personal property... elementary and secondary schools and non-profit organizations under initiatives to support science and mathematics education. (2) Field office feeder reports shall not include data for contractor inventory which...
41 CFR 109-43.4701 - Performance reports.
Code of Federal Regulations, 2013 CFR
2013-07-01
... Science Education Programs, using the following format, will include data for all personal property... elementary and secondary schools and non-profit organizations under initiatives to support science and mathematics education. (2) Field office feeder reports shall not include data for contractor inventory which...
41 CFR 109-43.4701 - Performance reports.
Code of Federal Regulations, 2011 CFR
2011-01-01
... Science Education Programs, using the following format, will include data for all personal property... elementary and secondary schools and non-profit organizations under initiatives to support science and mathematics education. (2) Field office feeder reports shall not include data for contractor inventory which...
Effect of artificial feeders on pollen loads of the hummingbirds of Cerro de la Muerte, Costa Rica.
Avalos, Gerardo; Soto, Alejandra; Alfaro, Willy
2012-03-01
Although sugar-water feeders are commonly used by enthusiasts to attract hummingbirds, little is known about how they affect hummingbird behavior and flower use. We studied the highland hummingbird assemblage of Cerro de La Muerte, Costa Rica, both at a site with permanent feeders (La Georgina Restaurant) and further from it. We examined how feeder use and monopolization affected seasonal changes in pollen loads during four sampling periods, including dry and wet seasons, from 2003-2005. We expected that species monopolizing the feeders would carry little or no pollen whatsoever, and would have pollen loads characterized by low floral diversity, in contrast with species less dependent on feeders. We obtained pollen samples from 183 individuals of four hummingbird species captured around the feeders using mist nets, which were compared with a pollen reference collection of plants with a pollination syndrome by hummingbirds. The same methods were implemented at a site 3km away from the feeders. Feeder usage was quantified by counting the number of times hummingbirds drank from the feeders in periods of 4min separated by 1min. The effects of hummingbird species and season on pollen load categories were assessed using a nominal logistic regression. The alpha species at the site, the Fiery-throated Hummingbird (Panterpe insignis), dominated the feeders during the dry season. Meanwhile, in the wet season, feeder usage was more evenly distributed across species, with the exception of the Volcano Hummingbird, Selasphorus flammula, which occupies the last place in the dominance hierarchy. Pollen loads of hummingbirds captured near feeders were low in abundance (more than 50% of captured individuals had zero or low pollen loads), and low in species richness (96% of the hummingbirds with pollen from only one plant genus, Centropogon). Overall pollen loads increased during the dry season coinciding with peaks in flower availability, although the majority of captured hummingbirds carried no pollen. Mist nets located 3km from La Georgina returned few captures (one-to-three specimens) per sampling date, contrasting with observations made before feeders were present. These results suggest that sugar-water feeders gather hummingbirds in over considerable distances drawing them away from flowers. The competitive and antagonistic pattern shown between feeders and flowers indicate that natural pollination system could be significantly altered. Supplementing hummingbirds with food seems likely to interfere with pollination networks already stressed by many anthropogenic effects.
Abdul Wahab, Muhammad Azmi; Fromont, Jane; Gomez, Oliver; Fisher, Rebecca; Jones, Ross
2017-09-15
Changes in turbidity, sedimentation and light over a two year large scale capital dredging program at Onslow, northwestern Australia, were quantified to assess their effects on filter feeder communities, in particular sponges. Community functional morphological composition was quantified using towed video surveys, while dive surveys allowed for assessments of species composition and chlorophyll content. Onslow is relatively diverse recording 150 sponge species. The area was naturally turbid (1.1 mean P 80 NTU), with inshore sites recording 6.5× higher turbidity than offshore localities, likely influenced by the Ashburton River discharge. Turbidity and sedimentation increased by up to 146% and 240% through dredging respectively, with corresponding decreases in light levels. The effects of dredging was variable, and despite existing caveats (i.e. bleaching event and passing of a cyclone), the persistence of sponges and the absence of a pronounced response post-dredging suggest environmental filtering or passive adaptation acquired pre-dredging may have benefited these communities. Copyright © 2017. Published by Elsevier Ltd.
ITER Magnet Feeder: Design, Manufacturing and Integration
NASA Astrophysics Data System (ADS)
CHEN, Yonghua; ILIN, Y.; M., SU; C., NICHOLAS; BAUER, P.; JAROMIR, F.; LU, Kun; CHENG, Yong; SONG, Yuntao; LIU, Chen; HUANG, Xiongyi; ZHOU, Tingzhi; SHEN, Guang; WANG, Zhongwei; FENG, Hansheng; SHEN, Junsong
2015-03-01
The International Thermonuclear Experimental Reactor (ITER) feeder procurement is now well underway. The feeder design has been improved by the feeder teams at the ITER Organization (IO) and the Institute of Plasma Physics, Chinese Academy of Sciences (ASIPP) in the last 2 years along with analyses and qualification activities. The feeder design is being progressively finalized. In addition, the preparation of qualification and manufacturing are well scheduled at ASIPP. This paper mainly presents the design, the overview of manufacturing and the status of integration on the ITER magnet feeders. supported by the National Special Support for R&D on Science and Technology for ITER (Ministry of Public Security of the People's Republic of China-MPS) (No. 2008GB102000)
Garitaonandia, Ibon; Amir, Hadar; Boscolo, Francesca Sesillo; Wambua, Gerald K.; Schultheisz, Heather L.; Sabatini, Karen; Morey, Robert; Waltz, Shannon; Wang, Yu-Chieh; Tran, Ha; Leonardo, Trevor R.; Nazor, Kristopher; Slavin, Ileana; Lynch, Candace; Li, Yingchun; Coleman, Ronald; Gallego Romero, Irene; Altun, Gulsah; Reynolds, David; Dalton, Stephen; Parast, Mana; Loring, Jeanne F.; Laurent, Louise C.
2015-01-01
The self-renewal and differentiation capacities of human pluripotent stem cells (hPSCs) make them a promising source of material for cell transplantation therapy, drug development, and studies of cellular differentiation and development. However, the large numbers of cells necessary for many of these applications require extensive expansion of hPSC cultures, a process that has been associated with genetic and epigenetic alterations. We have performed a combinatorial study on both hESCs and hiPSCs to compare the effects of enzymatic vs. mechanical passaging, and feeder-free vs. mouse embryonic fibroblast feeder substrate, on the genetic and epigenetic stability and the phenotypic characteristics of hPSCs. In extensive experiments involving over 100 continuous passages, we observed that both enzymatic passaging and feeder-free culture were associated with genetic instability, higher rates of cell proliferation, and persistence of OCT4/POU5F1-positive cells in teratomas, with enzymatic passaging having the stronger effect. In all combinations of culture conditions except for mechanical passaging on feeder layers, we noted recurrent deletions in the genomic region containing the tumor suppressor gene TP53, which was associated with decreased mRNA expression of TP53, as well as alterations in the expression of several downstream genes consistent with a decrease in the activity of the TP53 pathway. Among the hESC cultures, we also observed culture-associated variations in global gene expression and DNA methylation. The effects of enzymatic passaging and feeder-free conditions were also observed in hiPSC cultures. Our results highlight the need for careful assessment of the effects of culture conditions on cells intended for clinical therapies. PMID:25714340
Using supplemental food and its influence on survival of northern bobwhite (Colinus virginianus)
Townsend, D.E.; Lochmiller, R.L.; DeMaso, S.J.; Leslie, David M.; Peoples, A.D.; Scott, A C.; Parry, E.S.
2000-01-01
Biologists have debated the effectiveness of supplemental feeders as a management tool for the northern bobwhite (Colinus virginianus), but few extensive evaluations have been conducted. We examined 783 crops from harvested bobwhites during 1992-1996 to determine effects of climatic stress in winter on use of supplemental feeders and their impact on survival rate in winter. Crops of bobwhites harvested from areas with supplemental feeders contained 28.2% supplemental food compared with 5.5% (P<0.001) for those from areas without supplemental feeders. Winter climate was not a significant predictor of the proportional use of supplemental feeders. Rates of winter survival were greater on areas with supplemental feeders compared with non-supplemented areas in winters 1992-1993 (P=0.001) and 1993-1994 (P=0.002), but in 1994-1995, rates were greater on nonsupplemented areas (P=0.032). Cause-specific mortality rates indicated that supplemental feeders did not predispose bobwhites to hunter harvest or predators. Results suggested that bobwhites can gain nutritional benefits from supplemental feeders during times of severe winter stress.
Improvement of automatic fish feeder machine design
NASA Astrophysics Data System (ADS)
Chui Wei, How; Salleh, S. M.; Ezree, Abdullah Mohd; Zaman, I.; Hatta, M. H.; Zain, B. A. Md; Mahzan, S.; Rahman, M. N. A.; Mahmud, W. A. W.
2017-10-01
Nation Plan of action for management of fishing is target to achieve an efficient, equitable and transparent management of fishing capacity in marine capture fisheries by 2018. However, several factors influence the fishery production and efficiency of marine system such as automatic fish feeder machine could be taken in consideration. Two latest fish feeder machines have been chosen as the reference for this study. Based on the observation, it has found that the both machine was made with heavy structure, low water and temperature resistance materials. This research’s objective is to develop the automatic feeder machine to increase the efficiency of fish feeding. The experiment has conducted to testing the new design of machine. The new machine with maximum storage of 5 kg and functioning with two DC motors. This machine able to distribute 500 grams of pellets within 90 seconds and longest distance of 4.7 meter. The higher speed could reduce time needed and increase the distance as well. The minimum speed range for both motor is 110 and 120 with same full speed range of 255.
Gingival Fibroblasts as Autologous Feeders for Induced Pluripotent Stem Cells.
Yu, G; Okawa, H; Okita, K; Kamano, Y; Wang, F; Saeki, M; Yatani, H; Egusa, H
2016-01-01
Human gingival fibroblasts (hGFs) present an attractive source of induced pluripotent stem cells (iPSCs), which are expected to be a powerful tool for regenerative dentistry. However, problems to be addressed prior to clinical application include the use of animal-derived feeder cells for cultures. The aim of this study was to establish an autologous hGF-derived iPSC (hGF-iPSC) culture system by evaluating the feeder ability of hGFs. In both serum-containing and serum-free media, hGFs showed higher proliferation than human dermal fibroblasts (hDFs). Three hGF strains were isolated under serum-free conditions, although 2 showed impaired proliferation. When hGF-iPSCs were transferred onto mitomycin C-inactivated hGFs, hDFs, or mouse-derived SNL feeders, hGF and SNL feeders were clearly hGF-iPSC supportive for more than 50 passages, whereas hDF feeders were only able to maintain undifferentiated hGF-iPSC growth for a few passages. After 20 passages on hGF feeders, embryonic stem cell marker expression and CpG methylation at the NANOG and OCT3/4 promoters were similar for hGF-iPSCs cultured on hGF and SNL feeder cells. Long-term cultures of hGF-iPSCs on hGF feeders sustained their normal karyotype and pluripotency. On hGF feeders, hGF-iPSC colonies were surrounded by many colony-derived fibroblast-like cells, and the size of intact colonies at 7 d after passage was significantly larger than that on SNL feeders. Allogeneic hGF strains also maintained hGF-iPSCs for 10 passages. Compared with hDFs, hGFs showed a higher production of laminin-332, laminin α5 chain, and insulin-like growth factor-II, which have been reported to sustain the long-term self-renewal of pluripotent stem cells. These results suggest that hGFs possess an excellent feeder capability and thus can be used as alternatives to conventional mouse-derived SNL and hDF feeders. In addition, our findings suggest that hGF feeders are promising candidates for animal component-free ex vivo expansion of autologous hGF-iPSCs, thus providing an important step toward the future therapeutic application of hGF-iPSCs. © International & American Associations for Dental Research 2015.
Gunther, Idit; Raz, Tal; Even Zor, Yehonatan; Bachowski, Yuval; Klement, Eyal
2016-01-01
Cat feeders serve as an important source of available food for free-roaming cats (FRCs) and can play a central role in providing data on FRC distribution, welfare, and health. Data on cat feeder personalities as well as a better understanding of their feeding practices offer relevance for decision making concerning FRC population control strategies. The current study surveyed 222 FRC feeders who responded to a municipal trap-neuter-return (TNR) campaign in an Israeli central urban setting. The aim of the study was to describe their personal characteristics, feeding practices, and the FRC populations they feed. Feeders were divided into four groups according to the number of cats they claimed to feed per day (group 1: fed up to 5 cats, group 2: fed 6-10 cats, group 3: fed 11-20 cats, and group 4: fed ≥21 cats). Most feeders were women (81%), with a median age of 58 years (range 18-81). The feeders reported an overall feeding of 3337 cats in 342 different feeding locations. Feeders of group 4 comprised 15.31% (n = 34) of all feeders but fed 56% (n = 1869) of the FRC in 37.42% (n = 128) of the feeding locations. "Heavy" feeders (groups 3 and 4) reported that they traveled significantly longer distances in order to feed the cats. Commercial dry food consisted of 90% of the food they provided, with 66% of them feeding once a day, with less food per cat per day than the other feeder groups. Interestingly, "heavy" feeders were usually singles, had on average fewer siblings, a clear preference for owning cats as pets, and lived in lower income neighborhoods. According to the feeders' reports on the FRC populations they fed, 69.7% (2325/3337) cats were neutered and 11.8% (395/3337) were kittens. In addition, they reported that 1.6% (54/3337) of the cats were limping, 2% (67/3337) suffered from a systemic disease, 4% (135/3337) had skin lesions, and 3.9% (130/3337) were suffering from a chronic disability. Abundance of kittens and morbidity rate were significantly and negatively associated with neutering rate. These findings are in accordance with the suggestion that neutering may potentially improve cat welfare by reducing morbidity. Collaboration by the authorities with these heavy feeders, who represent a small number of FRC feeders and feed substantial FRC numbers, may be significant for the control and monitoring of FRC populations and their resources.
High-speed optical feeder-link system using adaptive optics
NASA Astrophysics Data System (ADS)
Arimoto, Yoshinori; Hayano, Yutaka; Klaus, Werner
1997-05-01
We propose a satellite laser communication system between a ground station and a geostationary satellite, named high- speed optical feeder link system. It is based on the application of (a) high-speed optical devices, which have been developed for ground-based high-speed fiber-optic communications, and (b) the adaptive optics which compensates wavefront distortions due to atmospheric turbulences using a real time feedback control. A link budget study shows that a system with 10-Gbps bit-rate are available assuming the state-of-the-art device performance of the Er-doped fiber amplifier. We further discuss preliminary measurement results of the atmospheric turbulence at the telescope site in Tokyo, and present current study on the design of the key components for the feeder-link laser transceiver.
30 CFR 75.1003-1 - Other requirements for guarding of trolley wires and trolley feeder wires.
Code of Federal Regulations, 2010 CFR
2010-07-01
... wires and trolley feeder wires. 75.1003-1 Section 75.1003-1 Mineral Resources MINE SAFETY AND HEALTH... Trolley Wires and Trolley Feeder Wires § 75.1003-1 Other requirements for guarding of trolley wires and trolley feeder wires. Adequate precaution shall be taken to insure that equipment being moved along...
30 CFR 75.1003-1 - Other requirements for guarding of trolley wires and trolley feeder wires.
Code of Federal Regulations, 2011 CFR
2011-07-01
... wires and trolley feeder wires. 75.1003-1 Section 75.1003-1 Mineral Resources MINE SAFETY AND HEALTH... Trolley Wires and Trolley Feeder Wires § 75.1003-1 Other requirements for guarding of trolley wires and trolley feeder wires. Adequate precaution shall be taken to insure that equipment being moved along...
The Use of Filter-feeders to Manage Disease in a Changing World.
Burge, Colleen A; Closek, Collin J; Friedman, Carolyn S; Groner, Maya L; Jenkins, Cody M; Shore-Maggio, Amanda; Welsh, Jennifer E
2016-10-01
Rapid environmental change is linked to increases in aquatic disease heightening the need to develop strategies to manage disease. Filter-feeding species are effective biofilters and can naturally mitigate disease risk to humans and wildlife. We review the role of filter-feeders, with an emphasis on bivalves, in altering disease outcomes via augmentation and reduction. Filtration can reduce transmission by removing pathogens from the water column via degradation and release of pathogens in pseudofeces. In other cases, filtration can increase pathogen transmission and disease risk. The effect of filtration on pathogen transmission depends on the selectivity of the filter-feeder, the degree of infectivity by the pathogen, the mechanism(s) of pathogen transmission and the ability of the pathogen to resist degradation. For example, some bacteria and viruses can resist degradation and accumulate within a filter-feeder leading to disease transmission to humans and other wildlife upon ingestion. Since bivalves can concentrate microorganisms, they are also useful as sentinels for the presence of pathogenic microorganisms. While somewhat less studied, other invertebrates, including ascidians and sponges may also provide ecosystem services by altering pathogen transmission. In all scenarios, climate change may affect the potential for filter-feeders to mitigate disease risk. We conclude that an assessment including empirical data and modeling of system-wide impacts should be conducted before selection of filter-feeders to mitigate disease. Such studies should consider physiology of the host and microbe and risk factors for negative impacts including augmentation of other pathogens. © The Author 2016. Published by Oxford University Press on behalf of the Society for Integrative and Comparative Biology. All rights reserved. For permissions please email: journals.permissions@oup.com.
A comparison of two systems for chlorinating water in rural Honduras.
Henderson, Amy K; Sack, R Bradley; Toledo, Erick
2005-09-01
This study investigated a small subset of the two community water-disinfection systems--hypochlorinators and tablet feeders-in rural Honduras. Levels of residual chlorine were assessed at three locations within the distribution system: the tank, the proximal house, and the distal house. The levels of residual chlorine were compared with the standard guidelines set by the Pan American Health Organization and the International Rural Water Association for potable water that require a minimum of 1.0 (tank), 0.5 (proximal house), and 0.2 (distal house) ppm for each location. The levels of residual chlorine were also compared across systems, e.g. hypochlorinators to tablet feeders. At the tank and proximal house, tablet feeders had significantly higher mean values for levels of residual chlorine (measured in ppm) than hypochlorinators (tank: 1.20 vs 0.67; proximal house: 0.44 vs 0.32, p < 0.001 for both) with no significant difference at the distal house (0.16 vs 0.16). At the tank and proximal house, tablet feeders were more likely to meet recommended standards than hypochlorinators (90.3% vs 13.3%, p < 0.0001 and 41.3% vs 23.7%, p < 0.0001) with a smaller difference seen at the distal house (30.6% vs 27.1%, p = 0.24). The apparent dichotomy in chlorine levels of tablet feeders (e.g. between tank/proximal house and distal house) is discussed. The results suggest that tablet feeders may be more effective than hypochlorinators in supplying clean water in rural, resource-poor settings and possibly serve as an alternative technology for water disinfection. Further research on techniques for empowering and building capacity within community water boards will help organize and introduce sustainable water systems in developing countries.
Roy, A; Krzykwa, E; Lemieux, R; Néron, S
2001-12-01
Several normal human cells, such as hematopoietic stem cells, dendritic cells, and B cells, can be cultured in vitro in defined optimal conditions. Several ex vivo culture systems require the use of feeder cells to support the growth of target cells. In such systems, proliferation of feeder cells has to be stopped, so that they can be used as nonreplicating viable support cells. Because feeder cells need to provide one or few active signals, it is important to maintain them in an metabolically active state, allowing continued expression of specific ligands or cytokines. Mitomycin C and gamma-irradiation treatments are commonly used to prepare nonproliferating feeder cells and are usually considered to be equivalent. Normal human B lymphocytes can be expanded in vitro in the presence of feeder cells expressing the CD40 ligand CD154. Here we compared the ability of gamma-irradiation- and mitomycin C-treated feeder cells to support the expansion of normal human B lymphocytes. The results indicate that expansion of B cells during a long-term culture was 100 times more potent using gamma-irradiated feeder cells compared to mitomycin C-treated cells. This difference could be related to a significant reduction in both cellular metabolism and level of CD154 expression observed in mitomycin C-treated feeder cells, but not in gamma-irradiated cells nor in control untreated cells. These results indicate that mitomycin C-treated feeder cells are metabolically altered, and consequently less efficient at maintaining cell expansion in the long-term cell culture system used.
Teotia, Pooja; Sharma, Shilpa; Airan, Balram; Mohanty, Sujata
2016-12-01
Human embryonic stem cell (hESC) lines are commonly maintained on inactivated feeder cells, in the medium supplemented with basic fibroblast growth factor (bFGF). However, limited availability of feeder cells in culture, and the high cost of growth factors limit their use in scalable expansion of hESC cultures for clinical application. Here, we describe an efficient and cost-effective feeder and bFGF-free culture of hESCs using conditioned medium (CM) from immortalized feeder cells. KIND-1 hESC cell line was cultured in CM, collected from primary mouse embryonic fibroblast, human foreskin fibroblast (HFF) and immortalized HFF (I-HFF). Pluripotency of KIND-1 hESC cell line was confirmed by expression of genes, proteins and cell surface markers. In culture, these cells retained normal morphology, expressed all cell surface markers, could differentiate to embryoid bodies upon culture in vitro. Furthermore, I-HFF feeder cells without supplementation of bFGF released ample amount of endogenous bFGF to maintain stemness of hESC cells. The study results described the use of CM from immortalized feeder cells as a consistent source and an efficient, inexpensive feeder-free culture system for the maintenance of hESCs. Moreover, it was possible to maintain hESCs without exogenous supplementation of bFGF. Thus, the study could be extended to scalable expansion of hESC cultures for therapeutic purposes.
Code of Federal Regulations, 2010 CFR
2010-07-01
... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Insulation of trolley wires, trolley feeder wires and bare signal wires; guarding of trolley wires and trolley feeder wires. 75.1003 Section 75.1003... MANDATORY SAFETY STANDARDS-UNDERGROUND COAL MINES Trolley Wires and Trolley Feeder Wires § 75.1003...
Code of Federal Regulations, 2011 CFR
2011-07-01
... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Insulation of trolley wires, trolley feeder wires and bare signal wires; guarding of trolley wires and trolley feeder wires. 75.1003 Section 75.1003... MANDATORY SAFETY STANDARDS-UNDERGROUND COAL MINES Trolley Wires and Trolley Feeder Wires § 75.1003...
Preobrazhenskaia, L A; Ioffe, M E; Mats, V N
2004-01-01
The role of the prefrontal cortex was investigated on the reaction of the active choice of the two feeders under changes value and probability reinforcement. The experiments were performed on 2 dogs with prefrontal ablation (g. proreus). Before the lesions the dogs were taught to receive food in two different feeders to conditioned stimuli with equally probable alimentary reinforcement. After ablation in the inter-trial intervals the dogs were running from the one feeder to another. In the answer to conditioned stimuli for many times the dogs choose the same feeder. The disturbance of the behavior after some times completely restored. In the experiments with competition of probability events and values of reinforcement the dogs chose the feeder with low-probability but better quality of reinforcement. In the experiments with equal value but different probability the intact dogs chose the feeder with higher probability. In our experiments the dogs with prefrontal lesions chose the each feeder equiprobably. Thus in condition of free behavior one of different functions of the prefrontal cortex is the reactions choose with more probability of reinforcement.
Real-time modeling and simulation of distribution feeder and distributed resources
NASA Astrophysics Data System (ADS)
Singh, Pawan
The analysis of the electrical system dates back to the days when analog network analyzers were used. With the advent of digital computers, many programs were written for power-flow and short circuit analysis for the improvement of the electrical system. Real-time computer simulations can answer many what-if scenarios in the existing or the proposed power system. In this thesis, the standard IEEE 13-Node distribution feeder is developed and validated on a real-time platform OPAL-RT. The concept and the challenges of the real-time simulation are studied and addressed. Distributed energy resources include some of the commonly used distributed generation and storage devices like diesel engine, solar photovoltaic array, and battery storage system are modeled and simulated on a real-time platform. A microgrid encompasses a portion of an electric power distribution which is located downstream of the distribution substation. Normally, the microgrid operates in paralleled mode with the grid; however, scheduled or forced isolation can take place. In such conditions, the microgrid must have the ability to operate stably and autonomously. The microgrid can operate in grid connected and islanded mode, both the operating modes are studied in the last chapter. Towards the end, a simple microgrid controller modeled and simulated on the real-time platform is developed for energy management and protection for the microgrid.
Effects of Feeder Cells on Dopaminergic Differentiation of Human Embryonic Stem Cells
Zhao, Zhenqiang; Ma, Yanlin; Chen, Zhibin; Liu, Qian; Li, Qi; Kong, Deyan; Yuan, Kunxiong; Hu, Lan; Wang, Tan; Chen, Xiaowu; Peng, Yanan; Jiang, Weimin; Yu, Yanhong; Liu, Xinfeng
2016-01-01
Mouse embryonic fibroblasts (MEFs) and human foreskin fibroblasts (HFFs) are used for the culture of human embryonic stem cells (hESCs). MEFs and HFFs differed in their capacity to support the proliferation and pluripotency of hESCs and could affect cardiac differentiation potential of hESCs. The aim of this study was to evaluate the effect of MEFs and HFFs feeders on dopaminergic differentiation of hESCs lines. To minimize the impact of culture condition variation, two hESCs lines were cultured on mixed feeder cells (MFCs, MEFs: HFFs = 1:1) and HFFs feeder, respectively, and then were differentiated into dopaminergic (DA) neurons under the identical protocol. Dopaminergic differentiation was evaluated by immunocytochemistry, quantitative fluorescent real-time PCR, transmission and scanning electron microscopy, and patch clamp. Our results demonstrated that these hESCs-derived neurons were genuine and functional DA neurons. However, compared to hESCs line on MFCs feeder, hESCs line on HFFs feeder had a higher proportion of tyrosine hydroxylase (TH) positive cells and expressed higher levels of FOXA2, PITX3, NURR1, and TH genes. In addition, the values of threshold intensity and threshold membrane potential of DA neurons from hESCs line on HFFs feeder were lower than those of DA neurons from hESCs line on the MFCs feeder. In conclusion, HFFs feeder not only facilitated the differentiation of hESCs cells into dopaminergic neurons, but also induced hESCs-derived DA neurons to express higher electrophysiological excitability. Therefore, feeder cells could affect not only dopaminergic differentiation potential of different hESCs lines, but also electrophysiological properties of hESCs-derived DA neurons. PMID:28066186
NASA Astrophysics Data System (ADS)
Kong, Xiangxi; Zhang, Xueliang; Chen, Xiaozhe; Wen, Bangchun; Wang, Bo
2016-05-01
In this paper, phase and speed synchronization control of four eccentric rotors (ERs) driven by induction motors in a linear vibratory feeder with unknown time-varying load torques is studied. Firstly, the electromechanical coupling model of the linear vibratory feeder is established by associating induction motor's model with the dynamic model of the system, which is a typical under actuated model. According to the characteristics of the linear vibratory feeder, the complex control problem of the under actuated electromechanical coupling model converts to phase and speed synchronization control of four ERs. In order to keep the four ERs operating synchronously with zero phase differences, phase and speed synchronization controllers are designed by employing adaptive sliding mode control (ASMC) algorithm via a modified master-slave structure. The stability of the controllers is proved by Lyapunov stability theorem. The proposed controllers are verified by simulation via Matlab/Simulink program and compared with the conventional sliding mode control (SMC) algorithm. The results show the proposed controllers can reject the time-varying load torques effectively and four ERs can operate synchronously with zero phase differences. Moreover, the control performance is better than the conventional SMC algorithm and the chattering phenomenon is attenuated. Furthermore, the effects of reference speed and parametric perturbations are discussed to show the strong robustness of the proposed controllers. Finally, experiments on a simple vibratory test bench are operated by using the proposed controllers and without control, respectively, to validate the effectiveness of the proposed controllers further.
Micro-feeding and dosing of powders via a small-scale powder pump.
Besenhard, M O; Fathollahi, S; Siegmann, E; Slama, E; Faulhammer, E; Khinast, J G
2017-03-15
Robust and accurate powder micro-feeding (<100mg/s) and micro-dosing (<5 mg) are major challenges, especially with regard to regulatory limitations applicable to pharmaceutical development and production. Since known micro-feeders that yield feed rates below 5mg/s use gravimetric feeding principles, feed rates depend primarily on powder properties. In contrast, volumetric powder feeders do not require regular calibration because their feed rates are primarily determined by the feeder's characteristic volume replacement. In this paper, we present a volumetric micro-feeder based on a cylinder piston system (i.e., a powder pump), which allows accurate micro-feeding and feed rates of a few grams per hours even for very fine powders. Our experimental studies addressed the influence of cylinder geometries, the initial conditions of bulk powder, and the piston speeds. Additional computational studies via Discrete Element Method simulations offered a better understanding of the feeding process, its possible limitations and ways to overcome them. The powder pump is a simple yet valuable tool for accurate powder feeding at feed rates of several orders of magnitude. Copyright © 2016 Elsevier B.V. All rights reserved.
Goyret, Joaquín; Kelber, Almut; Pfaff, Michael; Raguso, Robert A
2009-08-07
Here, we show that the consequences of deficient micronutrient (beta-carotene) intake during larval stages of Manduca sexta are carried across metamorphosis, affecting adult behaviour. Our manipulation of larval diet allowed us to examine how developmental plasticity impacts the interplay between visual and olfactory inputs on adult foraging behaviour. Larvae of M. sexta were reared on natural (Nicotiana tabacum) and artificial laboratory diets containing different concentrations of beta-carotene (standard diet, low beta-carotene, high beta-carotene and cornmeal). This vitamin-A precursor has been shown to be crucial for photoreception sensitivity in the retina of M. sexta. After completing development, post-metamorphosis, starved adults were presented with artificial feeders that could be either scented or unscented. Regardless of their larval diet, adult moths fed with relatively high probabilities on scented feeders. When feeders were unscented, moths reared on tobacco were more responsive than moths reared on beta-carotene-deficient artificial diets. Strikingly, moths reared on artificial diets supplemented with increasing amounts of beta-carotene (low beta and high beta) showed increasing probabilities of response to scentless feeders. We discuss these results in relationship to the use of complex, multi-modal sensory information by foraging animals.
Goyret, Joaquín; Kelber, Almut; Pfaff, Michael; Raguso, Robert A.
2009-01-01
Here, we show that the consequences of deficient micronutrient (β-carotene) intake during larval stages of Manduca sexta are carried across metamorphosis, affecting adult behaviour. Our manipulation of larval diet allowed us to examine how developmental plasticity impacts the interplay between visual and olfactory inputs on adult foraging behaviour. Larvae of M. sexta were reared on natural (Nicotiana tabacum) and artificial laboratory diets containing different concentrations of β-carotene (standard diet, low β-carotene, high β-carotene and cornmeal). This vitamin-A precursor has been shown to be crucial for photoreception sensitivity in the retina of M. sexta. After completing development, post-metamorphosis, starved adults were presented with artificial feeders that could be either scented or unscented. Regardless of their larval diet, adult moths fed with relatively high probabilities on scented feeders. When feeders were unscented, moths reared on tobacco were more responsive than moths reared on β-carotene-deficient artificial diets. Strikingly, moths reared on artificial diets supplemented with increasing amounts of β-carotene (low β and high β) showed increasing probabilities of response to scentless feeders. We discuss these results in relationship to the use of complex, multi-modal sensory information by foraging animals. PMID:19419987
NASA Astrophysics Data System (ADS)
Versilov, S. O.; Posylniy, Yu V.; Shurygin, D. N.; Tretyak, A. Ya
2017-10-01
The assessment of the geological conditions of development of existing ore deposits was made. For testing ore deposits in difficult mining and geological conditions, the authors proposed the system of development, accompanied by collapse of the mechanical ore with the use of feeders of active action that could be manufactured directly in the mine in accordance with the specific conditions of occurrence of minerals. The paper demonstrates the technology of manufacture of load-bearing structures of the feeder directly in the mine at the scene of the breaking of the first layer of ore, as well as the dynamics of the ore and the choice of parameters of concrete feeders. A new design of the bottom block was proposed, the idea of technical solution of which consists in the fact that it is offered to undergo the production of the smallest possible cross section, which is determined only by the dimensions of the conveyors to deliver ore. And before the explosion of fans of production wells, it is necessary to produce local collapse of the roof production to increase its height at the place of production of ore by blasting wellheads in two or three rows.
A Batch Feeder for Inhomogeneous Bulk Materials
NASA Astrophysics Data System (ADS)
Vislov, I. S.; Kladiev, S. N.; Slobodyan, S. M.; Bogdan, A. M.
2016-04-01
The work includes the mechanical analysis of mechanical feeders and batchers that find application in various technological processes and industrial fields. Feeders are usually classified according to their design features into two groups: conveyor-type feeders and non-conveyor feeders. Batchers are used to batch solid bulk materials. Less frequently, they are used for liquids. In terms of a batching method, they are divided into volumetric and weighting batchers. Weighting batchers do not provide for sufficient batching accuracy. Automatic weighting batchers include a mass controlling sensor and systems for automatic material feed and automatic mass discharge control. In terms of operating principle, batchers are divided into gravitational batchers and batchers with forced feed of material using conveyors and pumps. Improved consumption of raw materials, decreased loss of materials, ease of use in automatic control systems of industrial facilities allows increasing the quality of technological processes and improve labor conditions. The batch feeder suggested by the authors is a volumetric batcher that has no comparable counterparts among conveyor-type feeders and allows solving the problem of targeted feeding of bulk material batches increasing reliability and hermeticity of the device.
Holloway, Lawrence E.; Qu, Zhihua; Mohr-Schroeder, Margaret J.; ...
2017-02-06
In this study, we consider collaborative power systems education through the FEEDER consortium. To increase students' access to power engineering educational content, the consortium of seven universities was formed. A framework is presented to characterize different collaborative education activities among the universities. Three of these approaches of collaborative educational activities are presented and discussed. These include 1) cross-institutional blended courses ("MS-MD''); 2) cross-institutional distance courses ("SS-MD''); and 3) single-site special experiential courses and concentrated on-site programs available to students across consortium institutions ("MS-SD''). As a result, this paper presents the advantages and disadvantages of each approach.
Shared Ride Taxi Feeder Service in Memphis, TN
DOT National Transportation Integrated Search
1988-03-01
From May 1983 through October 1984, the Memphis Area Transit Authority (MATA) conducted the Taxi Feeder Demonstration Project. It entailed the operation of fixed-route feeder services through three low-density neighborhoods and one industrial park, c...
Derivation of Human Skin Fibroblast Lines for Feeder Cells of Human Embryonic Stem Cells.
Unger, Christian; Felldin, Ulrika; Rodin, Sergey; Nordenskjöld, Agneta; Dilber, Sirac; Hovatta, Outi
2016-02-03
After the first derivations of human embryonic stem cell (hESC) lines on fetal mouse feeder cell layers, the idea of using human cells instead of mouse cells as feeder cells soon arose. Mouse cells bear a risk of microbial contamination, and nonhuman immunogenic proteins are absorbed from the feeders to hESCs. Human skin fibroblasts can be effectively used as feeder cells for hESCs. The same primary cell line, which can be safely used for up to 15 passages after stock preparations, can be expanded and used for large numbers of hESC derivations and cultures. These cells are relatively easy to handle and maintain. No animal facilities or animal work is needed. Here, we describe the derivation, culture, and cryopreservation procedures for research-grade human skin fibroblast lines. We also describe how to make feeder layers for hESCs using these fibroblasts. Copyright © 2016 John Wiley & Sons, Inc.
Widowski, T M; Caston, L J; Casey-Trott, T M; Hunniford, M E
2017-09-01
Standards for feeder (a.k.a. feed trough) space allowance (SA) are based primarily on studies in conventional cages where laying hens tend to eat simultaneously, limiting feeder space. Large furnished cages (FC) offer more total space and opportunities to perform a greater variety of behaviors, which may affect feeding behavior and feeder space requirements. Our objective was to determine the effects of floor/feeder SA on behavior at the feeder. LSL-Lite hens were housed in FC equipped with a nest, perches, and a scratch mat. Hens with SA of either 520 cm2 (Low; 8.9 cm feeder space/hen) or 748 cm2 (High; 12.8 cm feeder space/hen) per bird resulted in groups of 40 vs. 28 birds in small FC (SFC) and 80 vs. 55 in large FC (LFC). Chain feeders ran at 0500, 0800, 1100, 1400, and 1700 with lights on at 0500 and off at 1900 hours. Digital recordings of FC were scanned at chain feeder onset and every 15 min for one h after (5 scans × 5 feeding times × 2 d) to count the number of birds with their head in the feeder. All occurrences of aggressive pecks and displacements during 2 continuous 30-minute observations at 0800 h and 1700 h also were counted. Mixed model repeated analyses tested the effects of SA, cage size, and time on the percent of hens feeding, and the frequency of aggressive pecks and displacements. Surprisingly, the percent of birds feeding simultaneously was similar regardless of cage size (LFC: 23.0 ± 0.9%; SFC: 24.0 ± 1.0%; P = 0.44) or SA (Low: 23.8 ± 0.9%; High: 23.3 ± 1.0%; P = 0.62). More birds were observed feeding at 1700 h (35.3 ± 0.1%) than any at other time (P < 0.001). Feeder use differed by cage area (nest, middle, or scratch) over the d (P < 0.001). The frequency of aggressive pecks was low overall and not affected by SA or cage size. Frequency of displacements was also low but greater at Low SA (P = 0.001). There was little evidence of feeder competition at the Low SA in this study. © The Author 2017. Published by Oxford University Press on behalf of Poultry Science Association.
39. CLOSE UP DETAIL OF THE FEEDER AND STAMP CONNECTION. ...
39. CLOSE UP DETAIL OF THE FEEDER AND STAMP CONNECTION. THE STAMP AN MORTAR BOX ARE ON THE LEFT AND THE FEEDER WITH ITS FEEDER DISK IS ON THE RIGHT. NOTE THE COLLAR ON THE CENTER STAMP STEM (UPPER LEFT CORNER OF THE IMAGE) THAT ACTIVATES THE LEVER IN THE CENTER OF THE PHOTO. THE COLLAR IS POSITIONED SUCH THAT WHEN THE LEVEL OF THE MATERIAL REACHES A LOW POINT IN THE MORTAR BOX IT PUSHES DOWN ON THE LEVER WHICH IN TURN ACTIVATES THE AUTOMATIC FEEDER DRIVE MECHANISM WHICH THEM DELIVERS ORE INTO THE BACKSIDE OF THE MORTAR BOX. - Standard Gold Mill, East of Bodie Creek, Northeast of Bodie, Bodie, Mono County, CA
Millard, W. J.
1979-01-01
An alternative means of delivering food to pigeons in operant conditioning research is described. The feeder allows greater control of the amount of food delivered and reduces the amount of time necessary for the pigeon to collect the food. It is possible to extend the length of experimental sessions due to the reduction of food intake. Data obtained using the pellet feeder indicated that the control of responding is comparable to that observed with the standard grain-magazine feeder. PMID:16812118
Extending Human Hematopoietic Stem Cell Survival In Vitro with Adipocytes
Glettig, Dean Liang
2013-01-01
Abstract Human hematopoietic stem cells (hHSCs) cannot be maintained in vitro for extended time periods because they rapidly differentiate or die. To extend in vitro culture time, researchers have made attempts to use human mesenchymal stem cells (hMSCs) to create feeder layers that mimic the stem cell niche. We have conducted an array of experiments including adipocytes in these feeder layers that inhibit hHSC differentiation and by that prolong stem cell survival in vitro. The amount of CD34+ cells was quantified using flow cytometry. In a first experiment, feeder layers of undifferentiated hMSCs were compared with feeder layers differentiated toward osteoblasts or adipocytes using minimal medium, showing the highest survival rate where adipocytes were included. The same conclusion was drawn in a second experiment in comparing hMSCs with adipogenic feeder cells, using a culture medium supplemented with a cocktail of hHSC growth factors. In a third experiment, it was shown that direct cell–cell contact is necessary for the supportive effect of the feeder layers. In a fourth and fifth experiment the amount of adipocytes in the feeder layers were varied, and in all experiments a higher amount of adipocytes in the feeder layers showed a less rapid decay of CD34+ cells at later time points. We therefore concluded that adipocytes assist in suppressing hHSC differentiation and aid in prolonging their survival in vitro. PMID:23741628
Microscopic suspension feeders near boundaries: Effects of external water flow
NASA Astrophysics Data System (ADS)
Pepper, Rachel; Koehl, M. A. R.
2015-11-01
Microscopic sessile suspension feeders are an important part of aquatic ecosystems and form a vital link in the transfer of carbon in aquatic food webs. These suspension feeders live attached to boundaries, consume bacteria and small detritus, and are in turn eaten by larger organisms. Many create a feeding current that draws fluid towards them, and from which they filter their food. In still water, the feeding current consists of recirculating eddies which form as a result of fluid forcing near a boundary. These recirculating eddies can be depleted of food and significantly decrease nutrient uptake; a variety of strategies have been proposed for how attached feeders increase their access to undepleted water. We investigate the interaction of the flow produced by a microscopic suspension feeder with external environmental flow, such as the current in a stream or ocean. We show through calculations that even very slow flow (on the order of microns per second) is sufficient to provide a constant supply of undepleted water to suspension feeders when the feeders are modeled with perfect nutrient capture efficiency and in the absence of diffusion. We also discuss which natural flow environments exceed the threshold to supply undepleted water and which do not, and we examine how characteristics of the suspension feeders themselves, such as stalk length and feeding disk size, influence feeding currents and their interactions with external flows.
Flow accelerated corrosion of carbon steel feeder pipes from pressurized heavy water reactors
NASA Astrophysics Data System (ADS)
Singh, J. L.; Kumar, Umesh; Kumawat, N.; Kumar, Sunil; Kain, Vivekanand; Anantharaman, S.; Sinha, A. K.
2012-10-01
Detailed investigation of a number of feeder pipes received from Rajasthan Atomic Power Station Unit 2 (RAPS#2) after en-masse feeder pipe replacement after 15.67 Effective Full Power Years (EFPYs) was carried out. Investigations included ultrasonic thickness measurement by ultrasonic testing, optical microscopy, scanning electron microscopy, chemical analysis and X-ray Diffraction (XRD). Results showed that maximum thickness reduction of the feeder had occurred downstream and close to the weld in 32 NB (1.25″/32.75 mm ID) elbows. Rate of Flow Accelerated Corrosion (FAC) was measured to be higher in the lower diameter feeder pipes due to high flow velocity and turbulence. Weld regions had thinned to a lower extent than the parent material due to higher chromium content in the weld. A weld protrusion has been shown to add to the thinning due to FAC and lead to faster thinning rate at localized regions. Surface morphology of inner surface of feeder had shown different size scallop pattern over the weld and parent material. Inter-granular cracks were also observed along the weld fusion line and in the parent material in 32 NB outlet feeder elbow.
Scafetta, Gaia; Tricoli, Eleonora; Siciliano, Camilla; Napoletano, Chiara; Puca, Rosa; Vingolo, Enzo Maria; Cavallaro, Giuseppe; Polistena, Andrea; Frati, Giacomo; De Falco, Elena
2013-12-01
Corneal epithelial regeneration through ex vivo expansion of limbal stem cells (LSCs) on 3T3-J2 fibroblasts has revealed some limitations mainly due to the corneal microenvironment not being properly replicated, thus affecting long term results. Insights into the feeder cells that are used to expand LSCs and the mechanisms underlying the effects of human feeder cells have yet to be fully elucidated. We recently developed a standardized methodology to expand human Tenon's fibroblasts (TFs). Here we aimed to investigate whether TFs can be employed as feeder cells for LSCs, characterizing the phenotype of the co-cultures and assessing what human soluble factors are secreted. The hypothesis that TFs could be employed as alternative human feeder layer has not been explored yet. LSCs were isolated from superior limbus biopsies, co-cultured on TFs, 3T3-J2 or dermal fibroblasts (DFs), then analyzed by immunofluorescence (p63α), colony-forming efficiency (CFE) assay and qPCR for a panel of putative stem cell and epithelial corneal differentiation markers (KRT3). Co-cultures supernatants were screened for a set of soluble factors. Results showed that the percentage of p63α(+)LSCs co-cultured onto TFs was significantly higher than those on DFs (p = 0.032) and 3T3-J2 (p = 0.047). Interestingly, LSCs co-cultures on TFs exhibited both significantly higher CFE and mRNA expression levels of ΔNp63α than on 3T3-J2 and DFs (p < 0.0001), showing also significantly greater levels of soluble factors (IL-6, HGF, b-FGF, G-CSF, TGF-β3) than LSCs on DFs. Therefore, TFs could represent an alternative feeder layer to both 3T3-J2 and DFs, potentially providing a suitable microenvironment for LSCs culture.
Code of Federal Regulations, 2010 CFR
2010-01-01
... AND ORDERS; MISCELLANEOUS COMMODITIES), DEPARTMENT OF AGRICULTURE LAMB PROMOTION, RESEARCH, AND INFORMATION ORDER Lamb Promotion, Research, and Information Order Definitions § 1280.107 Feeder. Feeder means any person who acquires ownership of lambs and feeds such lambs in the U.S. until they reach slaughter...
Simulation of rapid ecological change in Lake Ontario
McKenna, James E.; Chalupnicki, Marc; Dittman, Dawn E.; Watkins, James M.
2017-01-01
Lower trophic level processes are integral to proper functioning of large aquatic ecosystems and have been disturbed in Lake Ontario by various stressors including exotic species. The invasion of benthic habitats by dreissenid mussels has led to systemic changes and native faunal declines. Size-dependent physiological rates, spatial differences and connectivity, competition, and differential population dynamics among invertebrate groups contributed to the change and system complexity. We developed a spatially explicit, individual-based mechanistic model of the benthic ecosystem in Lake Ontario, with coupling to the pelagic system, to examine ecosystem dynamics and effects of dreissenid mussel invasion and native fauna losses. Benthic organisms were represented by functional groups; filter-feeders (i.e., dreissenid mussels), surface deposit-feeders (e.g., native amphipod Diporeia spp.), and deposit-feeders (e.g., oligochaetes and other burrowers). The model was stable, represented ecological structure and function effectively, and reproduced observed effects of the mussel invasion. Two hypotheses for causes of Diporeia loss, competition or disease-like mortality, were tested. Simple competition for food did not explain observed declines in native surface deposit-feeders during the filter-feeder invasion. However, the elevated mortality scenario supports a disease-like cause for loss of the native amphipod, with population changes in various lake areas and altered benthic biomass transfers. Stabilization of mussel populations and possible recovery of the native, surface-deposit feeding amphipod were predicted. Although further research is required on forcing functions, model parameters, and natural conditions, the model provides a valuable tool to help managers understand the benthic system and plan for response to future disruptions.
Relative Preference and Localized Food Affect Predator Space Use and Consumption of Incidental Prey
Schartel, Tyler E.; Schauber, Eric M.
2016-01-01
Abundant, localized foods can concentrate predators and their foraging efforts, thus altering both the spatial distribution of predation risk and predator preferences for prey that are encountered incidentally. However, few investigations have quantified the spatial scale over which localized foods affect predator foraging behavior and consumption of incidental prey. In spring 2010, we experimentally tested how point-source foods altered how generalist predators (white-footed mice, Peromyscus leucopus) utilized space and depredated two incidental prey items: almonds (Prunus dulcis; highly profitable) and maple seeds (Acer saccharum; less profitable). We estimated mouse population densities with trapping webs, quantified mouse consumption rates of these incidental prey items, and measured local mouse activity with track plates. We predicted that 1) mouse activity would be elevated near full feeders, but depressed at intermediate distances from the feeder, 2) consumption of both incidental prey would be high near feeders providing less-preferred food and, 3) consumption of incidental prey would be contingent on predator preference for prey relative to feeders providing more-preferred food. Mouse densities increased significantly from pre- to post-experiment. Mean mouse activity was unexpectedly greatest in control treatments, particularly <15 m from the control (empty) feeder. Feeders with highly preferred food (sunflower seeds) created localized refuges for incidental prey at intermediate distances (15 to 25m) from the feeder. Feeders with less-preferred food (corn) generated localized high risk for highly preferred almonds <10 m of the feeder. Our findings highlight the contingent but predictable effects of locally abundant food on risk experienced by incidental prey, which can be positive or negative depending on both spatial proximity and relative preference. PMID:26978659
Aflatoxin contamination in corn sold for wildlife feed in texas.
Dunham, Nicholas R; Peper, Steven T; Downing, Carson D; Kendall, Ronald J
2017-05-01
Supplemental feeding with corn to attract and manage deer is a common practice throughout Texas. Other species, including northern bobwhites (Colinus virginianus), are commonly seen feeding around supplemental deer feeders. In many cases, supplemental feeding continues year-round so feed supply stores always have supplemental corn in stock. Fluctuating weather and improper storage of corn can lead to and/or amplify aflatoxin contamination. Due to the recent decline of bobwhites throughout the Rolling Plains ecoregion of Texas, there has been interest in finding factors such as toxins that could be linked to their decline. In this study, we purchased and sampled supplemental corn from 19 locations throughout this ecoregion to determine if aflatoxin contamination was present in individual bags prior to being dispersed to wildlife. Of the 57 bags sampled, 33 bags (approximately 58%) contained aflatoxin with a bag range between 0.0-19.91 parts per billion (ppb). Additionally, three metal and three polypropylene supplemental feeders were each filled with 45.4 kg of triple cleaned corn and placed in an open field to study long-term aflatoxin buildup. Feeders were sampled every 3 months from November 2013-November 2014. Average concentration of aflatoxin over the year was 4.08 ± 2.53 ppb (±SE) in metal feeders, and 1.43 ± 0.89 ppb (±SE) in polypropylene feeders. The concentration of aflatoxins is not affected by the type of feeder (metal vs polypropylene), the season corn was sampled, and the location in the feeder (top, middle, bottom) where corn is sampled. It is unlikely that corn used in supplemental feeders is contributing to the bobwhite decline due to the low levels of aflatoxin found in purchased corn and long-term storage of corn used in supplemental feeders.
Relative Preference and Localized Food Affect Predator Space Use and Consumption of Incidental Prey.
Schartel, Tyler E; Schauber, Eric M
2016-01-01
Abundant, localized foods can concentrate predators and their foraging efforts, thus altering both the spatial distribution of predation risk and predator preferences for prey that are encountered incidentally. However, few investigations have quantified the spatial scale over which localized foods affect predator foraging behavior and consumption of incidental prey. In spring 2010, we experimentally tested how point-source foods altered how generalist predators (white-footed mice, Peromyscus leucopus) utilized space and depredated two incidental prey items: almonds (Prunus dulcis; highly profitable) and maple seeds (Acer saccharum; less profitable). We estimated mouse population densities with trapping webs, quantified mouse consumption rates of these incidental prey items, and measured local mouse activity with track plates. We predicted that 1) mouse activity would be elevated near full feeders, but depressed at intermediate distances from the feeder, 2) consumption of both incidental prey would be high near feeders providing less-preferred food and, 3) consumption of incidental prey would be contingent on predator preference for prey relative to feeders providing more-preferred food. Mouse densities increased significantly from pre- to post-experiment. Mean mouse activity was unexpectedly greatest in control treatments, particularly <15 m from the control (empty) feeder. Feeders with highly preferred food (sunflower seeds) created localized refuges for incidental prey at intermediate distances (15 to 25m) from the feeder. Feeders with less-preferred food (corn) generated localized high risk for highly preferred almonds <10 m of the feeder. Our findings highlight the contingent but predictable effects of locally abundant food on risk experienced by incidental prey, which can be positive or negative depending on both spatial proximity and relative preference.
Diatom feeding across trophic guilds in tidal flat nematodes, and the importance of diatom cell size
NASA Astrophysics Data System (ADS)
Moens, Tom; Vafeiadou, Anna-Maria; De Geyter, Ellen; Vanormelingen, Pieter; Sabbe, Koen; De Troch, Marleen
2014-09-01
We examine the capacity of nematodes from three feeding types (deposit feeder, epistrate feeder, predator) to utilize microphytobenthos (MPB), and assess whether diatom cell size and consumer body size are important drivers of their feeding. We analyzed natural stable isotope ratios of carbon and nitrogen in abundant nematode genera and a variety of carbon sources at an estuarine intertidal flat. All nematodes had δ13C indicating that MPB is their major carbon source. δ15N, however, demonstrated that only one deposit and one epistrate feeder genus obtained most of their carbon from direct grazing on MPB, whereas other deposit feeders and predators obtained at least part of their carbon by predation on MPB grazers. We then performed a microcosm experiment in which equal cell numbers of each of three differently sized strains of the pennate diatom Seminavis were offered as food to four, one and one genera of deposit feeders, epistrate feeders and predators, respectively. Previous studies have shown that all but the epistrate feeder ingest whole diatoms, whereas the epistrate feeder pierces cells and sucks out their contents. Most genera showed markedly higher carbon absorption from medium and large cells than from small ones. When considering the number of cells consumed, however, none of the nematodes which ingest whole cells exhibited a clear preference for any specific diatom size. The epistrate feeder was the smallest nematode taxon considered here, yet it showed a marked preference for large cells. These results highlight that the feeding mechanism is much more important than consumer size as a driver of particle size selection in nematodes grazing MPB.
NASA Astrophysics Data System (ADS)
Galerne, C. Y.; Galland, O.; Neumann, E. R.; Planke, S.
2009-12-01
The structural relationships between sills and their feeders are poorly documented because they are rarely observed in the field and difficult to image on seismic data. For instance, it is unclear whether sills are fed by pipes, dikes or other sills. Nevertheless, the geometrical relationships between sills and their feeders provide first-order constraints on magma emplacement mechanisms. Here, we investigate the structural and geochemical relationships between sills and potential feeder dikes in a remarkably well-preserved and exposed sill complex, the Golden Valley Sill Complex (GVSC), Karoo Basin, South Africa. The GVSC consists of five major saucer-shaped sills and six dikes. The Golden Valley sill itself is an elliptical saucer, with a N-S trend. A one meter thick dike (D4) crops out underneath the southern tip of the Golden Valley sill. The strike of this dike is parallel to the long axis of the Golden Valley sill. Detailed sampling and geochemical analyses of the GVSC show that each sill and dike exhibits a specific geochemical signature. The Golden Valley sill and its underlying dike D4 have identical signatures. Although there is no clear structural evidence, the consistent geometrical and geochemical relationships between the Golden Valley sill and the D4 dike suggest that this vertical linear structure is the feeder of the overlying saucer-shaped sill. In order to investigate the relationships between sills and feeders, we resorted to scaled laboratory experiments. The experiments consisted of a low-viscosity vegetable oil representing magma and a cohesive fine-grained silica flour representing brittle rocks. We placed a horizontal weak layer into the silica flour, just above the top of the inlet, to simulate strata. Such a weak layer controlled the formation of horizontal sill that subsequently turned into a transgressive sheet leading to the formation of a saucer geometry. We ran experiments with varying inlet shapes: 1) a point inlet representing a pipe-like feeder and 2) a linear feeder representing a dike-like feeder. In the experiments with point inlet, circular saucer-shaped sills formed. In the experiments with linear feeder, elliptical saucer-shaped sills formed. In the latter experiments, the long axes of the saucers were parallel to, and located directly above, the linear feeder. The experiments show that the feeder geometry has an important influence on the geometry of the emplaced sills. There are close similarities between the geometry of the Golden Valley sill and the intrusions formed in the experiments. The elliptical shape of the Golden Valley sill suggests that it was fed by an elongated feeder, probably the D4 dike. In general, our results show that the three-dimensional geometry of saucer-shaped sills observed in sedimentary basins, may constrain the shape of their feeders, i.e. their emplacement mechanisms.
Analysis of broadcasting satellite service feeder link power control and polarization
NASA Technical Reports Server (NTRS)
Sullivan, T. M.
1982-01-01
Statistical analyses of carrier to interference power ratios (C/Is) were performed in assessing 17.5 GHz feeder links using (1) fixed power and power control, and (2) orthogonal linear and orthogonal circular polarizations. The analysis methods and attenuation/depolarization data base were based on CCIR findings to the greatest possible extent. Feeder links using adaptive power control were found to neither cause or suffer significant C/I degradation relative to that for fixed power feeder links having similar or less stringent availability objectives. The C/Is for sharing between orthogonal linearly polarized feeder links were found to be significantly higher than those for circular polarization only in links to nominally colocated satellites from nominally colocated Earth stations in high attenuation environments.
Economic feeder for recharging and ``topping off''
NASA Astrophysics Data System (ADS)
Fickett, Bryan; Mihalik, G.
2000-04-01
Increasing the size of the melt charge significantly increases yield and reduces costs. Siemens Solar Industries is optimizing a method to charge additional material after meltdown (top-off) using an external feeder system. A prototype feeder system was fabricated consisting of a hopper and feed delivery system. The low-cost feeder is designed for simple operation and maintenance. The system is capable of introducing up to 60 kg of granular silicon while under vacuum. An isolation valve permits refilling of the hopper while maintaining vacuum in the growth furnace. Using the feeder system in conjunction with Siemens Solar Industries' energy efficient hot zone dramatically reduces power and argon consumption. Throughput is also improved as faster pull speeds can be attained. The increased pull speeds have an even greater impact when the charge size is increased. Further cost reduction can be achieved by refilling the crucible after crystal growth and pulling a second ingot run. Siemens Solar Industries is presently testing the feeder in production.
Troxel, T R; Barham, B L
2007-12-01
The objectives of the study were to determine how factors affecting the selling price of feeder calves changed from 2000 to 2005 and to examine the perception that discounts narrow or even disappear as calf supplies decrease and selling prices increase. Data from weekly Arkansas livestock auctions were collected from January 1 to December 31 in 2000 and 2005. Data included calf sex, breed type, color, muscle score, horn status, frame score, fill, condition, health, and BW. Mean selling prices for 2000 and 2005 were $92.91 +/- 15.05 and $118.32 +/- 15.13 (mean +/- SD; $/45.45 kg), respectively. Individual price observations were subtracted from the respective annual means and became the dependent variable. The selling prices for feeder calves sold in groups of 2 to 5 calves and in groups of >/= 6 calves were greater in 2005 than 2000 (P < 0.001). Steers received a greater premium ($6.48 +/- 0.09 vs. $6.02 +/- 0.08; mean +/- SE) and bull calves received greater discounts ($0.30 +/- 0.14 vs. $1.68 +/- 0.09) in 2005 than in 2000. Breeds types that increased in value from 2000 to 2005 were Angus x Hereford, Angus, Angus x Charolais, and Brahman (P < 0.001). Breed types that received a reduced selling price in 2005 compared with 2000 (P < 0.001) were one-fourth Brahman Cross, Charolais, Charolais x Limousin, Hereford x Limousin, Limousin, Limousin x one-fourth Brahman, Longhorn, Saler and Simmental. Yellow-white face, black-white face, black, and gray feeder calves received an increase in selling price from 2000 to 2005 (P < 0.001). Although fewer horned feeder calves were sold in 2005 (P < 0.01), they received greater discounts in 2005 than 2000 (-$2.86 +/- 0.16 and -$0.51 +/- 0.09; P < 0.001). In 2005, large-framed feeder calves did not receive the premium detected in 2000, but medium-framed feeder calves in 2005 received a greater selling price compared with 2000. Feeder calves with a muscle score of 1 received a greater premium in 2005 compared with 2000 ($2.58 +/- 0.06 and $0.02 +/- 0.09, respectively; P < 0.001). Feeder calves with a muscle score of 2 were discounted in both years, but the discount in 2005 was not as great as in 2000 (P < 0.001). Full and tanked feeder calves received greater discounts in 2005 than in 2000 (P < 0.001). Discounts for fleshy and fat feeder calves were greater in 2005 than in 2000. Most factors affecting the selling price of Arkansas feeder calves in 2000 affected the selling price in 2005. Although feeder calf supplies were smaller in 2005 than 2000, many discounts increased.
46 CFR 111.75-1 - Lighting feeders.
Code of Federal Regulations, 2010 CFR
2010-10-01
... COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) ELECTRICAL ENGINEERING ELECTRIC SYSTEMS-GENERAL REQUIREMENTS Lighting Circuits and Protection § 111.75-1 Lighting feeders. (a) Passenger vessels. On a... lighting, feeders, and branch circuits are in subpart 112.43 of this chapter. [CGD 74-125A, 47 FR 15236...
34 CFR 280.2 - Who is eligible to apply for a grant?
Code of Federal Regulations, 2010 CFR
2010-07-01
... SECONDARY EDUCATION, DEPARTMENT OF EDUCATION MAGNET SCHOOLS ASSISTANCE PROGRAM General § 280.2 Who is... this section only if he determines that for each magnet school for which funding is sought, the magnet..., either in the magnet school or in a feeder school, as appropriate. (Authority: 20 U.S.C. 7231c) [50 FR...
46 CFR 112.43-15 - Emergency lighting feeders.
Code of Federal Regulations, 2011 CFR
2011-10-01
... 46 Shipping 4 2011-10-01 2011-10-01 false Emergency lighting feeders. 112.43-15 Section 112.43-15 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) ELECTRICAL ENGINEERING EMERGENCY LIGHTING AND POWER SYSTEMS Emergency Lighting Systems § 112.43-15 Emergency lighting feeders. For a vessel with...
46 CFR 112.43-15 - Emergency lighting feeders.
Code of Federal Regulations, 2010 CFR
2010-10-01
... 46 Shipping 4 2010-10-01 2010-10-01 false Emergency lighting feeders. 112.43-15 Section 112.43-15 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) ELECTRICAL ENGINEERING EMERGENCY LIGHTING AND POWER SYSTEMS Emergency Lighting Systems § 112.43-15 Emergency lighting feeders. For a vessel with...
46 CFR 112.43-15 - Emergency lighting feeders.
Code of Federal Regulations, 2014 CFR
2014-10-01
... 46 Shipping 4 2014-10-01 2014-10-01 false Emergency lighting feeders. 112.43-15 Section 112.43-15 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) ELECTRICAL ENGINEERING EMERGENCY LIGHTING AND POWER SYSTEMS Emergency Lighting Systems § 112.43-15 Emergency lighting feeders. For a vessel with...
46 CFR 112.43-15 - Emergency lighting feeders.
Code of Federal Regulations, 2012 CFR
2012-10-01
... 46 Shipping 4 2012-10-01 2012-10-01 false Emergency lighting feeders. 112.43-15 Section 112.43-15 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) ELECTRICAL ENGINEERING EMERGENCY LIGHTING AND POWER SYSTEMS Emergency Lighting Systems § 112.43-15 Emergency lighting feeders. For a vessel with...
46 CFR 112.43-15 - Emergency lighting feeders.
Code of Federal Regulations, 2013 CFR
2013-10-01
... 46 Shipping 4 2013-10-01 2013-10-01 false Emergency lighting feeders. 112.43-15 Section 112.43-15 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) ELECTRICAL ENGINEERING EMERGENCY LIGHTING AND POWER SYSTEMS Emergency Lighting Systems § 112.43-15 Emergency lighting feeders. For a vessel with...
77 FR 34876 - Airworthiness Directives; The Boeing Company
Federal Register 2010, 2011, 2012, 2013, 2014
2012-06-12
... (a flammable fluid leakage zone) or heat damage to the APU power feeder cable, insulation blankets... heat damage to the APU power feeder cable, insulation blankets, or pressure bulkhead. Relevant Service... feeder cable and heat damage of the insulation blanket adjacent to the clamp, a detailed inspection for...
Terry, Lesley L; Vasey, Paul L
2011-06-01
Feederism is a fat fetish subculture in which individuals eroticize weight gain and feeding. Feeders are individuals who claim to become sexually aroused by feeding their partners and encouraging them to gain weight. Conversely, Feedees are individuals who claim to become sexually aroused by eating, being fed, and the idea or act of gaining weight. Very little is known about this population. This report describes a woman who self-identified as a Feedee. It is unclear, at present, whether female Feederism represents a unique paraphilia or a thematic variation of morphophilia or sexual masochism.
Lee, Jae-Il; Lee, Chi-Woo; Kwon, Hyouk-Sang; Kim, Young-Tae; Park, Chung-Gyu; Kim, Sang-Joon; Kang, Byeong-Cheol
2008-10-01
The majority of newly acquired nonhuman primates encounter serious problems adapting themselves to new environments or facilities. In particular, loss of appetite and abnormal behavior can occur in response to environmental stresses. These adaptation abnormalities can ultimately have an affect on the animal's growth and well-being. In this study, we evaluated the affects of a puzzle feeder on the food intake and abnormal behavior of newly acquired rhesus monkeys for a short period. The puzzle feeder was applied to 47- to 58-month-old animals that had never previously encountered one. We found that there was no difference in the change of food intake between the bucket condition and the puzzle feeder condition. In contrast, the time spent for consumption of food was three times longer in the puzzle feeder condition than in the bucket condition. Two monkeys initially exhibited stereotypic behavior. One showed a decreasing, and the other an increasing pattern of abnormal behavior after introduction of the puzzle feeder. In conclusion, this result suggests that over a short period, the puzzle feeder can only affect the time for food consumption since it failed to affect the food intake and did not consistently influence stereotypic behaviors in newly acquired rhesus monkeys.
Yang, Hua; Qiu, Ying; Zeng, Xianghui; Ding, Yan; Zeng, Jianye; Lu, Kehuan; Li, Dongsheng
2016-06-01
The aim of the present study was to investigate the effects of feeder layers composed of various ratios of mouse embryonic fibroblasts (MEFs) and human foreskin fibroblasts (hFFs) on the growth of human embryonic stem cells (hESCs). In addition, the secretion levels of basic fibroblast growth factor (bFGF) by the feeder layers was detected. MEFs and hFFs were treated with mitomycin C and seeded onto gelatin-coated plates at a density of 1×10 8 cells/l. The hFFs and MEFs were combined and plated at the following ratios: 0:1, 1:2, 1:1, 2:1 and 1:0. The secretion of bFGF by the various hFF/MEF ratio feeder layers was detected using an enzyme-linked immunosorbent assay. Subsequently, hESCs were cultured on top of the various feeder layers. The differences in the cellular morphology of the hESCs were observed using microscopy, and the expression levels alkaline phosphatase (AKP) and octamer-binding transcription factor 4 (OCT-4) were detected using immunohistochemical analysis as indicators of differentiation status. The results showed that the hFFs secreted substantial quantities of bFGF, while no bFGF was secreted by the MEFs. The clones of hESC growing on the feeder layer containing MEF or hFF alone were flat. By contrast, hESC clones grown on a mixed feeder layer containing hFFs + MEFs at a ratio of 1:1 exhibited an accumulated growth with a clear edge, as compared with the other ratios. In addition, hESCs growing on the feeder layer were positive for the expression of AKP and OCT-4. In summary, feeder layer hFFs secreted bFGF, while MEFs did not, indicating that bFGF is not the only factor that supports the growth and differentiation of hESCs. The optimal growth of hESCs was achieved using a mixed feeder layer composed of hFFs + MEFs at a ratio of 1:1.
NASA Astrophysics Data System (ADS)
Goodale, Eben; Kim, Edward; Nabors, Annika; Henrichon, Sara; Nieh, James C.
2014-06-01
Nectar guides can enhance pollinator efficiency and plant fitness by allowing pollinators to more rapidly find and remember the location of floral nectar. We tested if a radiating nectar guide around a nectary would enhance the ability of naïve bumble bee foragers to find nectar. Most experiments that test nectar guide efficacy, specifically radiating linear guides, have used guides positioned around the center of a radially symmetric flower, where nectaries are often found. However, the flower center may be intrinsically attractive. We therefore used an off-center guide and nectary and compared "conjunct" feeders with a nectar guide surrounding the nectary to "disjunct" feeders with a nectar guide separated from the nectary. We focused on the innate response of novice bee foragers that had never previously visited such feeders. We hypothesized that a disjunct nectar guide would conflict with the visual information provided by the nectary and negatively affect foraging. Approximately, equal numbers of bumble bees ( Bombus impatiens) found nectar on both feeder types. On disjunct feeders, however, unsuccessful foragers spent significantly more time (on average 1.6-fold longer) searching for nectar than any other forager group. Successful foragers on disjunct feeders approached these feeders from random directions unlike successful foragers on conjunct feeders, which preferentially approached the combined nectary and nectar guide. Thus, the nectary and a surrounding nectar guide can be considered a combination of two signals that attract naïve foragers even when not in the floral center.
Goodale, Eben; Kim, Edward; Nabors, Annika; Henrichon, Sara; Nieh, James C
2014-06-01
Nectar guides can enhance pollinator efficiency and plant fitness by allowing pollinators to more rapidly find and remember the location of floral nectar. We tested if a radiating nectar guide around a nectary would enhance the ability of naïve bumble bee foragers to find nectar. Most experiments that test nectar guide efficacy, specifically radiating linear guides, have used guides positioned around the center of a radially symmetric flower, where nectaries are often found. However, the flower center may be intrinsically attractive. We therefore used an off-center guide and nectary and compared "conjunct" feeders with a nectar guide surrounding the nectary to "disjunct" feeders with a nectar guide separated from the nectary. We focused on the innate response of novice bee foragers that had never previously visited such feeders. We hypothesized that a disjunct nectar guide would conflict with the visual information provided by the nectary and negatively affect foraging. Approximately, equal numbers of bumble bees (Bombus impatiens) found nectar on both feeder types. On disjunct feeders, however, unsuccessful foragers spent significantly more time (on average 1.6-fold longer) searching for nectar than any other forager group. Successful foragers on disjunct feeders approached these feeders from random directions unlike successful foragers on conjunct feeders, which preferentially approached the combined nectary and nectar guide. Thus, the nectary and a surrounding nectar guide can be considered a combination of two signals that attract naïve foragers even when not in the floral center.
26 CFR 1.502-1 - Feeder organizations.
Code of Federal Regulations, 2010 CFR
2010-04-01
... 26 Internal Revenue 7 2010-04-01 2010-04-01 true Feeder organizations. 1.502-1 Section 1.502-1...) INCOME TAXES (CONTINUED) Exempt Organizations § 1.502-1 Feeder organizations. (a) In the case of an organization operated for the primary purpose of carrying on a trade or business for profit, exemption is not...
Federal Register 2010, 2011, 2012, 2013, 2014
2010-02-24
... DEPARTMENT OF THE INTERIOR Bureau of Reclamation Bunker Hill Groundwater Basin, Riverside-Corona...) will prepare a joint EIS/EIR for the proposed Riverside-Corona Feeder Project. The public and agencies... participate in the planning, design, and construction of the Riverside-Corona Feeder Project including: (i) 20...
Code of Federal Regulations, 2011 CFR
2011-01-01
... feeder pig that is sold shall pay an assessment on that animal, unless such producer demonstrates to the Board by appropriate documentation that an assessment was previously paid on that animal as a feeder pig... purchaser of a porcine animal raised by a producer as a feeder pig or market hog shall collect an assessment...
Code of Federal Regulations, 2010 CFR
2010-01-01
... feeder pig that is sold shall pay an assessment on that animal, unless such producer demonstrates to the Board by appropriate documentation that an assessment was previously paid on that animal as a feeder pig... purchaser of a porcine animal raised by a producer as a feeder pig or market hog shall collect an assessment...
Code of Federal Regulations, 2012 CFR
2012-01-01
... feeder pig that is sold shall pay an assessment on that animal, unless such producer demonstrates to the Board by appropriate documentation that an assessment was previously paid on that animal as a feeder pig... purchaser of a porcine animal raised by a producer as a feeder pig or market hog shall collect an assessment...
Code of Federal Regulations, 2014 CFR
2014-01-01
... feeder pig that is sold shall pay an assessment on that animal, unless such producer demonstrates to the Board by appropriate documentation that an assessment was previously paid on that animal as a feeder pig... purchaser of a porcine animal raised by a producer as a feeder pig or market hog shall collect an assessment...
Code of Federal Regulations, 2013 CFR
2013-01-01
... feeder pig that is sold shall pay an assessment on that animal, unless such producer demonstrates to the Board by appropriate documentation that an assessment was previously paid on that animal as a feeder pig... purchaser of a porcine animal raised by a producer as a feeder pig or market hog shall collect an assessment...
DOE Office of Scientific and Technical Information (OSTI.GOV)
Zhu, Xiangqi; Zhang, Yingchen
This paper presents an optimal voltage control methodology with coordination among different voltage-regulating resources, including controllable loads, distributed energy resources such as energy storage and photovoltaics (PV), and utility voltage-regulating devices such as voltage regulators and capacitors. The proposed methodology could effectively tackle the overvoltage and voltage regulation device distortion problems brought by high penetrations of PV to improve grid operation reliability. A voltage-load sensitivity matrix and voltage-regulator sensitivity matrix are used to deploy the resources along the feeder to achieve the control objectives. Mixed-integer nonlinear programming is used to solve the formulated optimization control problem. The methodology has beenmore » tested on the IEEE 123-feeder test system, and the results demonstrate that the proposed approach could actively tackle the voltage problem brought about by high penetrations of PV and improve the reliability of distribution system operation.« less
Cartwright, E. J.; Nguyen, T.; Melluso, C.; Ayers, T.; Lane, C.; Hodges, A.; Li, X.; Quammen, J.; Yendell, S. J.; Adams, J.; Mitchell, J.; Rickert, R.; Klos, R.; Williams, I. T.; Behravesh, C. Barton; Wright, J.
2015-01-01
While most human Salmonella infections result from exposure to contaminated foods, an estimated 11% of all Salmonella infections are attributed to animal exposures, including both direct animal handling and indirect exposures such as cleaning cages and handling contaminated pet food. This report describes the epidemiologic, environmental and laboratory investigations conducted in the United States as part of the response to an international outbreak of tetracycline-resistant Salmonella enterica serotype I 4,[5],12:i:- infections with over 500 illnesses occurring from 2008 to 2010. This investigation found that illness due to the outbreak strain was significantly associated with exposure to pet reptiles and frozen feeder rodents used as food for pet reptiles. Salmonella isolates indistinguishable from the outbreak strain were isolated from a frozen feeder mice-fed reptile owned by a case patient, as well as from frozen feeder mice and environmental samples collected from a rodent producing facility (Company A). An international voluntary recall of all Company A produced frozen feeder animals sold between May 2009 and July 2010 occurred. Only 13% of cases in our investigation were aware of the association between Salmonella infection and mice or rats. Consumers, the pet industry, healthcare providers and veterinarians need to be aware of the potential health risk posed by feeder rodents, whether live or frozen. Frozen feeder rodent producers, suppliers and distributors should follow the animal food labelling requirements as described in 21 CFR §501.5, and all packages of frozen feeder rodents should include safe handling instructions. Persons should wash their hands thoroughly with soap and water after handling live or frozen feeder rodents, as well as reptiles or anything in the area where the animals live. Continued opportunities exist for public health officials, the pet industry, veterinarians and consumers to work together to prevent salmonellosis associated with pet food, pets and other animals. PMID:25996458
Cartwright, E J; Nguyen, T; Melluso, C; Ayers, T; Lane, C; Hodges, A; Li, X; Quammen, J; Yendell, S J; Adams, J; Mitchell, J; Rickert, R; Klos, R; Williams, I T; Barton Behravesh, C; Wright, J
2016-02-01
While most human Salmonella infections result from exposure to contaminated foods, an estimated 11% of all Salmonella infections are attributed to animal exposures, including both direct animal handling and indirect exposures such as cleaning cages and handling contaminated pet food. This report describes the epidemiologic, environmental and laboratory investigations conducted in the United States as part of the response to an international outbreak of tetracycline-resistant Salmonella enterica serotype I 4,[5],12:i:- infections with over 500 illnesses occurring from 2008 to 2010. This investigation found that illness due to the outbreak strain was significantly associated with exposure to pet reptiles and frozen feeder rodents used as food for pet reptiles. Salmonella isolates indistinguishable from the outbreak strain were isolated from a frozen feeder mice-fed reptile owned by a case patient, as well as from frozen feeder mice and environmental samples collected from a rodent producing facility (Company A). An international voluntary recall of all Company A produced frozen feeder animals sold between May 2009 and July 2010 occurred. Only 13% of cases in our investigation were aware of the association between Salmonella infection and mice or rats. Consumers, the pet industry, healthcare providers and veterinarians need to be aware of the potential health risk posed by feeder rodents, whether live or frozen. Frozen feeder rodent producers, suppliers and distributors should follow the animal food labelling requirements as described in 21 CFR §501.5, and all packages of frozen feeder rodents should include safe handling instructions. Persons should wash their hands thoroughly with soap and water after handling live or frozen feeder rodents, as well as reptiles or anything in the area where the animals live. Continued opportunities exist for public health officials, the pet industry, veterinarians and consumers to work together to prevent salmonellosis associated with pet food, pets and other animals. © 2015 Blackwell Verlag GmbH.
DOE Office of Scientific and Technical Information (OSTI.GOV)
Ruth, Mark; Pratt, Annabelle; Lunacek, Monte
2015-07-17
The combination of distributed energy resources (DER) and retail tariff structures to provide benefits to both utility consumers and the utilities is poorly understood. To improve understanding, an Integrated Energy System Model (IESM) is being developed to simulate the physical and economic aspects of DER technologies, the buildings where they reside, and feeders servicing them. The IESM was used to simulate 20 houses with home energy management systems on a single feeder under a time of use tariff to estimate economic and physical impacts on both the households and the distribution utilities. HEMS reduce consumers’ electric bills by precooling housesmore » in the hours before peak electricity pricing. Household savings are greater than the reduction utility net revenue indicating that HEMS can provide a societal benefit providing tariffs are structured so that utilities remain solvent. Utilization of HEMS reduce peak loads during high price hours but shifts it to hours with off-peak and shoulder prices and resulting in a higher peak load.« less
Experimental Model School Unit. Application for Continuation Grant. P.L. 89-10 ESEA, Title III.
ERIC Educational Resources Information Center
Charlotte-Mecklenburg Public Schools, Charlotte, NC.
This application for continuation of an ESEA, Title III, grant to the Charlotte-Mecklenburg, N.C., Schools' Experimental Model School Unit (a senior high school and its two junior high and six elementary feeder schools with a program of research, experimentation, innovation, and dissemination designed to act as a catalyst for curriculum,…
Ornithologists by Design: Kindergarteners Design, Construct, and Evaluate Bird Feeders
ERIC Educational Resources Information Center
Shorter, Angela; Segers, Marcia
2016-01-01
How can an engineer design a bird feeder that attracts many birds? This question resulted from kindergarten students' observations of the bird feeders in their school's bird sanctuary. The challenging question is the heart of project-based learning (PBL), a teaching strategy in which students tackle real-world problems and design projects to solve…
USDA-ARS?s Scientific Manuscript database
The objective of this study was to evaluate the effects of moisture addition at the gin stand feeder conditioning hopper and/or the battery condenser slide on gin performance and Western cotton fiber quality and textile processing. The test treatments included no moisture addition, feeder hopper hum...
19. DETAIL OF STAMP BATTERY AUTOMATIC FEEDER, LOOKING EAST. THIS ...
19. DETAIL OF STAMP BATTERY AUTOMATIC FEEDER, LOOKING EAST. THIS IS THE MIDDLE OF THREE FEEDERS, ONE FOR EACH STAMP BATTERY. THE CHUTE (UPPER RIGHT) INTRODUCED THE CRUSHED ORE FROM THE ORE BIN. FLOW WAS CONTROLLED BY A SLIDING DOOR ON THE UPPER LEVEL. - Skidoo Mine, Park Route 38 (Skidoo Road), Death Valley Junction, Inyo County, CA
Oliveira, J L; Xin, H; Wu, H
2018-05-30
Current feeder space recommendations in laying hen welfare guidelines are inconsistent among and within countries. One determining criterion forming the recommendations (e.g. 12.0 cm/hen for the EU guideline) is that all birds can feed simultaneously. However, if there are other resources in the environment, as in enriched colony housing (ECH), it is unknown whether group-housed hens will choose to feed simultaneously. This study assesses the impact of feeder space on feeding behavior of 60 laying hens (W-36) in ECH using a ultra-high frequency radio-frequency identification-based tracking system. The feeder spaces investigated were 12.0, 9.5, 8.5 and 6.5 cm/hen, achieved by blocking portions of the overall feeder access to keep hens at the same stocking density. Each feeder space treatment, randomly assigned over the course of the experiment, lasted for 7 consecutive days. Feeding behaviors were characterized as daily time spent at the feeder (TS, min/hen-day), daily frequency of visits to the feeder (FV, #/hen-day), and maximum or average percentage of hens feeding simultaneously (MPB, APB, %). Group-average daily feed intake (FI, g/hen-day), water use (WU, g/hen-day), and hen-day egg production (HDEP, %) were also measured. The results revealed that at 12.0 cm/hen, where unoccupied feeder space was present, a maximum of 59.0±1.4% (average of 31.7±0.3%) hens fed simultaneously. No significant differences were detected among 12.0, 9.5 and 8.5 cm/hen in TS (293±10, 286±10 and 281±10 min/hen-day) and MPB (59.0±1.4, 57.3±1.4 and 53.3±1.4%) (P>0.05). The outcome of no significant differences also held true between 12.0 and 9.5 cm/hen in APB (31.7±0.3 v. 30.8±0.3%) and between 9.5 and 8.5 cm/hen in all response variables measured (P>0.05). However, there were significant differences in APB between 6.5 cm/hen and all other treatments; in TS and FV between 6.5 and 9.5 cm/hen; and in MPB between 6.5 and 12 cm/hen (P0.05). The results revealed that synchronous feeding of hens in the ECH did not increase with increasing feeder space. However, it is worth noting that lower feeder space may lead to aggression or frustration which was not quantified in the current study.
Iwazawa, J; Ohue, S; Hashimoto, N; Mitani, T
2014-02-01
To compare the accuracy of computer software analysis using three different target-definition protocols to detect tumour feeder vessels for transarterial chemoembolization of hepatocellular carcinoma. C-arm computed tomography (CT) data were analysed for 81 tumours from 57 patients who had undergone chemoembolization using software-assisted detection of tumour feeders. Small, medium, and large-sized targets were manually defined for each tumour. The tumour feeder was verified when the target tumour was enhanced on selective C-arm CT of the investigated vessel during chemoembolization. The sensitivity, specificity, and accuracy of the three protocols were evaluated and compared. One hundred and eight feeder vessels supplying 81 lesions were detected. The sensitivity of the small, medium, and large target protocols was 79.8%, 91.7%, and 96.3%, respectively; specificity was 95%, 88%, and 50%, respectively; and accuracy was 87.5%, 89.9%, and 74%, respectively. The sensitivity was significantly higher for the medium (p = 0.003) and large (p < 0.001) target protocols than for the small target protocol. The specificity and accuracy were higher for the small (p < 0.001 and p < 0.001, respectively) and medium (p < 0.001 and p < 0.001, respectively) target protocols than for the large target protocol. The overall accuracy of software-assisted automated feeder analysis in transarterial chemoembolization for hepatocellular carcinoma is affected by the target definition size. A large target definition increases sensitivity and decreases specificity in detecting tumour feeders. A target size equivalent to the tumour size most accurately predicts tumour feeders. Copyright © 2013 The Royal College of Radiologists. Published by Elsevier Ltd. All rights reserved.
Foraging scent marks of bumblebees: footprint cues rather than pheromone signals
NASA Astrophysics Data System (ADS)
Wilms, Jessica; Eltz, Thomas
2008-02-01
In their natural habitat foraging bumblebees refuse to land on and probe flowers that have been recently visited (and depleted) by themselves, conspecifics or other bees, which increases their overall rate of nectar intake. This avoidance is often based on recognition of scent marks deposited by previous visitors. While the term ‘scent mark’ implies active labelling, it is an open question whether the repellent chemicals are pheromones actively and specifically released during flower visits, or mere footprints deposited unspecifically wherever bees walk. To distinguish between the two possibilities, we presented worker bumblebees ( Bombus terrestris) with three types of feeders in a laboratory experiment: unvisited control feeders, passive feeders with a corolla that the bee had walked over on its way from the nest (with unspecific footprints), and active feeders, which the bee had just visited and depleted, but which were immediately refilled with sugar water (potentially with specific scent marks). Bumblebees rejected both active and passive feeders more frequently than unvisited controls. The rate of rejection of passive feeders was only slightly lower than that of active feeders, and this difference vanished completely when passive corollas were walked over repeatedly on the way from the nest. Thus, mere footprints were sufficient to emulate the repellent effect of an actual feeder visit. In confirmation, glass slides on which bumblebees had walked on near the nest entrance accumulated hydrocarbons (alkanes and alkenes, C23 to C31), which had previously been shown to elicit repellency in flower choice experiments. We conclude that repellent scent marks are mere footprints, which foraging bees avoid when they encounter them in a foraging context.
Expression and secretory profile of buffalo fetal fibroblasts and Wharton's jelly feeder layers.
Parmar, Mehtab S; Mishra, Smruti Ranjan; Somal, Anjali; Pandey, Sriti; Kumar, G Sai; Sarkar, Mihir; Chandra, Vikash; Sharma, G Taru
2017-05-01
The present study examined the comparative expression and secretory profile of vital signaling molecules in buffalo fetal fibroblasts (BFF) and Wharton's jelly (BWJ) feeder layers at different passages. Both feeder layers were expanded up to 8th passage. Signaling molecules viz. bone morphogenetic protein 4 (BMP4), fibroblast growth factor 2 (FGF2), leukemia inhibitory factor (LIF) and transforming growth factor beta 1 (TGFB1) and pluripotency-associated transcriptional factors (POU5F1, SOX2, NANOG, KLF4, MYC and FOXD3) were immunolocalized in the both feeder types. A clear variation in the expression pattern of key signaling molecules with passaging was registered in both feeders compared to primary culture (0 passage). The conditioned media (CM) was collected from different passages (2, 4, 6, 8) of both the feeder layers and was quantified using enzyme-linked immunosorbent assay (ELISA). Concomitant to expression profile, protein quantification also revealed differences in the concentration of signaling molecules at different time points. Conjointly, expression and secretory profile revealed that 2nd passage of BFF and 6th passage of BWJ exhibit optimal levels of key signaling molecules thus may be selected as best passages for embryonic stem cells (ESCs) propagation. Further, the effect of mitomycin-C (MMC) treatment on the expression profile of signaling molecules in the selected passages of BFF and BWJ revealed that MMC modulates the expression profile of these molecules. In conclusion, the results indicate that feeder layers vary in expression and secretory pattern of vital signaling molecules with passaging. Based on these findings, the appropriate feeder passages may be selected for the quality propagation of buffalo ESCs. Copyright © 2017 Elsevier B.V. All rights reserved.
DOE Office of Scientific and Technical Information (OSTI.GOV)
Zhu, Xiangqi; Wang, Jiyu; Mulcahy, David
This paper presents a voltage-load sensitivity matrix (VLSM) based voltage control method to deploy demand response resources for controlling voltage in high solar penetration distribution feeders. The IEEE 123-bus system in OpenDSS is used for testing the performance of the preliminary VLSM-based voltage control approach. A load disaggregation process is applied to disaggregate the total load profile at the feeder head to each load nodes along the feeder so that loads are modeled at residential house level. Measured solar generation profiles are used in the simulation to model the impact of solar power on distribution feeder voltage profiles. Different casemore » studies involving various PV penetration levels and installation locations have been performed. Simulation results show that the VLSM algorithm performance meets the voltage control requirements and is an effective voltage control strategy.« less
Broadcasting satellite feeder links - Characteristics and planning
NASA Technical Reports Server (NTRS)
Kiebler, J. W.
1982-01-01
The paper presents the results of recent studies by the Feeder Link Sub-Working Group of the FCC Advisory Committee for the 1983 Regional Administrative Radio Conference (RARC). These studies conclude that specification of a few key parameters will make feeder link planning relatively straightforward. Feeder links can be located anywhere within a country if satellite orbit locations are separated by 10 deg for adjacent service areas and key parameter values presented in the paper are adopted. Colocated satellites serving a common service area need special attention to attain sufficient isolation between a desired channel and its adjacent cross-polarized channels and alternate co-polarized channels. In addition to presenting planning conclusions by the Advisory Committee, the paper presents and analyzes actions of the International Radio Consultative Committee's Conference Planning Meeting (CPM) concerning feeder links. The CPM reached conclusions similar to, and compatible with, those of the Advisory Committee.
Consequences of Feeder Delays for the Success of A380 Operations
NASA Technical Reports Server (NTRS)
Ruehle, Jens; Goetsch, Bjoern; Koch, Benjamin
2006-01-01
Due to existing slot and infrastructure constraints at international hub-and-spoke airports, an increase in feeder traffic seems only possible if larger feeder aircraft are used. Using a case study of Lufthansa German Airlines at Frankfurt International Airport, three possible A380 routes (Beijing, Tokyo-Narita, Los Angeles) were examined to assess the extent to which delays of feeder traffic may impact the economic performance of very large aircraft. On the basis of today s delays and anticipated traffic growth in the future, we found that between 9.5% and 13.5% of connecting passengers are unable to transfer to their respective intercontinental flights. In addition, the results demonstrate that a further increase in delays can be detrimental to the profitable operation of very large aircraft, as demonstrated by two out of three simulated routes. We suggest options for airlines operating very large aircraft to counteract the negative impacts of feeder delays.
Krause, Katrina M; Lovelady, Cheryl A; Peterson, Bercedis L; Chowdhury, Najmul; Østbye, Truls
2010-12-01
Pregnancy-related weight retention can contribute to obesity, and breast-feeding may facilitate postpartum weight loss. We investigated the effect of breast-feeding on postpartum weight retention. A retrospective follow-up study of weight retention, compared in women who were fully breast-feeding, combining breast-feeding with formula-feeding (mixed feeding), or formula-feeding at 3 months (n 14 330) or 6 months (n 4922) postpartum, controlling for demographic and weight-related covariates using multiple linear regression. The North Carolina Special Supplemental Nutrition Program for Women, Infants, and Children (WIC). Participants in the North Carolina WIC Programme who delivered a baby between 1996 and 2004. In covariate-adjusted analyses, there was no association between breast-feeding and weight retention at 3 months postpartum. At 6 months postpartum, as compared to formula-feeders, mean weight retention was 0·84 kg lower in mixed feeders (95 % CI 0·39, 1·29; P = 0·0002) and 1·38 kg lower in full breast-feeders (95 % CI 0·89, 1·87; P ≤ 0·0001). Breast-feeding was inversely associated with weight retention at 6 months postpartum in this large, racially diverse sample of low-income women. Further, full breast-feeding had a larger protective effect than did breast-feeding combined with formula-feeding.
USDA-ARS?s Scientific Manuscript database
The effects of feeder type and supplemental monensin on hay utilization in beef cows was investigated using 56 crossbred beef cows (BW= 494 ± 50 kg; BCS= 5.2 ± 0.5) in a split-plot treatment arrangement with a completely randomized design. Supplement treatment served as the main plot and feeder desi...
High pressure rotary piston coal feeder
NASA Technical Reports Server (NTRS)
Gardner, J. F.; Gencsoy, H. T.; Strimbeck, D. C.
1977-01-01
This feeder concept uniquely combines the functions of solids feeding, metering, and pressurization into one compact system. Success with the rotary-piston concept would provide a lower-cost alternative to lock-hopper systems. The design of the feeder is presented, with special emphasis on the difficult problem of seal design. Initial tests will be to check seal performance. Subsequent tests will evaluate solids-feeding ability.
NASA Technical Reports Server (NTRS)
Evans, JuliAnn (Inventor); Gundo, Daniel P. (Inventor); Harper, Jennifer S. (Inventor); Mulenburg, Gerald M. (Inventor); Skundberg, Thomas L. (Inventor)
1996-01-01
An animal feeder for use in a metabolic cage is introduced. The feeder includes a confined passageway and an adjustable notched gate proceeding a food cup. The gate is adjusted so that the entry area to the food cup approximates the cross sectional head area of the animal. Food ejected from the food cup by a caged animal is dropped through a grate into a spill tray.
Code of Federal Regulations, 2011 CFR
2011-01-01
... 7 Agriculture 10 2011-01-01 2011-01-01 false Collection and remittance of assessments for the sale of feeder pigs and market hogs. 1230.113 Section 1230.113 Agriculture Regulations of the Department... pigs and market hogs. Pursuant to the provisions of § 1230.71, purchasers of feeder pigs or market hogs...
Code of Federal Regulations, 2014 CFR
2014-01-01
... 7 Agriculture 10 2014-01-01 2014-01-01 false Collection and remittance of assessments for the sale of feeder pigs and market hogs. 1230.113 Section 1230.113 Agriculture Regulations of the Department... pigs and market hogs. Pursuant to the provisions of § 1230.71, purchasers of feeder pigs or market hogs...
Code of Federal Regulations, 2012 CFR
2012-01-01
... 7 Agriculture 10 2012-01-01 2012-01-01 false Collection and remittance of assessments for the sale of feeder pigs and market hogs. 1230.113 Section 1230.113 Agriculture Regulations of the Department... pigs and market hogs. Pursuant to the provisions of § 1230.71, purchasers of feeder pigs or market hogs...
Code of Federal Regulations, 2013 CFR
2013-01-01
... 7 Agriculture 10 2013-01-01 2013-01-01 false Collection and remittance of assessments for the sale of feeder pigs and market hogs. 1230.113 Section 1230.113 Agriculture Regulations of the Department... pigs and market hogs. Pursuant to the provisions of § 1230.71, purchasers of feeder pigs or market hogs...
Code of Federal Regulations, 2010 CFR
2010-01-01
... 7 Agriculture 10 2010-01-01 2010-01-01 false Collection and remittance of assessments for the sale of feeder pigs and market hogs. 1230.113 Section 1230.113 Agriculture Regulations of the Department... pigs and market hogs. Pursuant to the provisions of § 1230.71, purchasers of feeder pigs or market hogs...
Limat, A; Hunziker, T; Boillat, C; Noser, F; Wiesmann, U
1990-07-01
In vitro, human dermal fibroblasts (HDF) differentiate through morphologically and biochemically identified compartments. In the course of this spontaneous differentiation through mitotic and postmitotic states, a tremendous increase in cellular and nuclear size occurs. Induction of postmitotic states can be accelerated by chemical (e.g., mitomycin C) or physical (e.g., x-ray) treatments. Such experimentally induced postmitotic HDF cells support very efficiently the growth of cutaneous epithelial cells, i.e. interfollicular keratinocytes and follicular outer root sheath cells, especially in primary cultures starting from very low cell seeding densities. The HDF feeder system provides more fundamental and also practical advantages, i.e. use of initially diploid human fibroblasts from known anatomic locations, easy handling and excellent reproducibility, and the possibility of long-term storage by incubation at 37 degrees C. Conditions for the cryogenic storage of postmitotic HDF cells in liquid nitrogen are presented and related to the feeder capacity for epithelial cell growth. Because postmitotic HDF cells preserve intact feeder properties after long-term storage, the immediate availability of feeder cells and the possibility to repeat experiments with identical materials further substantiate the usefulness of this feeder system.
DOE Office of Scientific and Technical Information (OSTI.GOV)
Postigo Marcos, Fernando E.; Domingo, Carlos Mateo; San Roman, Tomas Gomez
Under the increasing penetration of distributed energy resources and new smart network technologies, distribution utilities face new challenges and opportunities to ensure reliable operations, manage service quality, and reduce operational and investment costs. Simultaneously, the research community is developing algorithms for advanced controls and distribution automation that can help to address some of these challenges. However, there is a shortage of realistic test systems that are publically available for development, testing, and evaluation of such new algorithms. Concerns around revealing critical infrastructure details and customer privacy have severely limited the number of actual networks published and that are available formore » testing. In recent decades, several distribution test feeders and US-featured representative networks have been published, but the scale, complexity, and control data vary widely. This paper presents a first-of-a-kind structured literature review of published distribution test networks with a special emphasis on classifying their main characteristics and identifying the types of studies for which they have been used. As a result, this both aids researchers in choosing suitable test networks for their needs and highlights the opportunities and directions for further test system development. In particular, we highlight the need for building large-scale synthetic networks to overcome the identified drawbacks of current distribution test feeders.« less
Postigo Marcos, Fernando E.; Domingo, Carlos Mateo; San Roman, Tomas Gomez; ...
2017-11-18
Under the increasing penetration of distributed energy resources and new smart network technologies, distribution utilities face new challenges and opportunities to ensure reliable operations, manage service quality, and reduce operational and investment costs. Simultaneously, the research community is developing algorithms for advanced controls and distribution automation that can help to address some of these challenges. However, there is a shortage of realistic test systems that are publically available for development, testing, and evaluation of such new algorithms. Concerns around revealing critical infrastructure details and customer privacy have severely limited the number of actual networks published and that are available formore » testing. In recent decades, several distribution test feeders and US-featured representative networks have been published, but the scale, complexity, and control data vary widely. This paper presents a first-of-a-kind structured literature review of published distribution test networks with a special emphasis on classifying their main characteristics and identifying the types of studies for which they have been used. As a result, this both aids researchers in choosing suitable test networks for their needs and highlights the opportunities and directions for further test system development. In particular, we highlight the need for building large-scale synthetic networks to overcome the identified drawbacks of current distribution test feeders.« less
NASA Astrophysics Data System (ADS)
Sánchez, Daniel; Nieh, James C.; Hénaut, Yann; Cruz, Leopoldo; Vandame, Rémy
Several studies have examined the existence of recruitment communication mechanisms in stingless bees. However, the spatial accuracy of location-specific recruitment has not been examined. Moreover, the location-specific recruitment of reactivated foragers, i.e., foragers that have previously experienced the same food source at a different location and time, has not been explicitly examined. However, such foragers may also play a significant role in colony foraging, particularly in small colonies. Here we report that reactivated Scaptotrigona mexicana foragers can recruit with high precision to a specific food location. The recruitment precision of reactivated foragers was evaluated by placing control feeders to the left and the right of the training feeder (direction-precision tests) and between the nest and the training feeder and beyond it (distance-precision tests). Reactivated foragers arrived at the correct location with high precision: 98.44% arrived at the training feeder in the direction trials (five-feeder fan-shaped array, accuracy of at least +/-6° of azimuth at 50 m from the nest), and 88.62% arrived at the training feeder in the distance trials (five-feeder linear array, accuracy of at least +/-5 m or +/-10% at 50 m from the nest). Thus, S. mexicana reactivated foragers can find the indicated food source at a specific distance and direction with high precision, higher than that shown by honeybees, Apis mellifera, which do not communicate food location at such close distances to the nest.
Number of hummingbird visits determines flower mite abundance on hummingbird feeders.
Márquez-Luna, Ubaldo; Vázquez González, María Magdalena; Castellanos, Ignacio; Ortiz-Pulido, Raúl
2016-08-01
Members of several genera of mites from the family Melicharidae (Mesostigmata) use hummingbirds as transport host to move from flower to flower, where they feed on pollen and nectar. The factors that influence hummingbird flower mite abundance on host plant flowers are not currently known. Here we tested whether hummingbird flower mite abundance on an artificial nectar source is determined by number of hummingbird visits, nectar energy content or species richness of visiting hummingbirds. We conducted experiments employing hummingbird feeders with sucrose solutions of low, medium, and high energy concentrations, placed in a xeric shrubland. In the first experiment, we recorded the number of visiting hummingbirds and the number of visiting hummingbird species, as well as the abundance of hummingbird flower mites on each feeder. Feeders with the highest sucrose concentration had the most hummingbird visits and the highest flower mite abundances; however, there was no significant effect of hummingbird species richness on mite abundance. In the second experiment, we recorded flower mite abundance on feeders after we standardized the number of hummingbird visits to them. Abundance of flower mites did not differ significantly between feeders when we controlled for hummingbird visits. Our results suggest that nectar energy concentration determines hummingbird visits, which in turn determines flower mite abundance in our feeders. Our results do not support the hypothesis that mites descend from hummingbird nostrils more on richer nectar sources; however, it does not preclude the possibility that flower mites select for nectar concentration at other spatial and temporal scales.
Code of Federal Regulations, 2012 CFR
2012-10-01
.... (a) Operators of NGSO MSS feeder link earth stations and GSO FSS earth stations in the band 29.25 to... MSS feeder link earth station complexes, that will minimize instances of unacceptable interference to the GSO FSS space stations. Earth station licensees operating with GSO FSS systems shall be capable of...
Code of Federal Regulations, 2012 CFR
2012-10-01
... Earth-to-space transmissions from feeder link earth station complexes. A “feeder link earth station complex” may include up to three (3) earth station groups, with each earth station group having up to four... NGSO MSS licensees or applicants pursuant to § 101.147. (b) A maximum of seven (7) feeder link earth...
Code of Federal Regulations, 2014 CFR
2014-10-01
... Earth-to-space transmissions from feeder link earth station complexes. A “feeder link earth station complex” may include up to three (3) earth station groups, with each earth station group having up to four... NGSO MSS licensees or applicants pursuant to § 101.147. (b) A maximum of seven (7) feeder link earth...
Code of Federal Regulations, 2011 CFR
2011-10-01
... Earth-to-space transmissions from feeder link earth station complexes. A “feeder link earth station complex” may include up to three (3) earth station groups, with each earth station group having up to four... NGSO MSS licensees or applicants pursuant to § 101.147. (b) A maximum of seven (7) feeder link earth...
Code of Federal Regulations, 2010 CFR
2010-10-01
... Earth-to-space transmissions from feeder link earth station complexes. A “feeder link earth station complex” may include up to three (3) earth station groups, with each earth station group having up to four... NGSO MSS licensees or applicants pursuant to § 101.147. (b) A maximum of seven (7) feeder link earth...
Code of Federal Regulations, 2011 CFR
2011-10-01
.... (a) Operators of NGSO MSS feeder link earth stations and GSO FSS earth stations in the band 29.25 to... MSS feeder link earth station complexes, that will minimize instances of unacceptable interference to the GSO FSS space stations. Earth station licensees operating with GSO FSS systems shall be capable of...
Code of Federal Regulations, 2013 CFR
2013-10-01
.... (a) Operators of NGSO MSS feeder link earth stations and GSO FSS earth stations in the band 29.25 to... MSS feeder link earth station complexes, that will minimize instances of unacceptable interference to the GSO FSS space stations. Earth station licensees operating with GSO FSS systems shall be capable of...
Code of Federal Regulations, 2013 CFR
2013-10-01
... feeder link earth stations in the 17/24 GHz BSS. 25.223 Section 25.223 Telecommunication FEDERAL....223 Off-axis EIRP spectral density limits for feeder link earth stations in the 17/24 GHz BSS. (a) This section applies to all applications for earth station licenses in the 17/24 GHz BSS frequency...
Code of Federal Regulations, 2011 CFR
2011-10-01
... feeder link earth stations in the 17/24 GHz BSS. 25.223 Section 25.223 Telecommunication FEDERAL....223 Off-axis EIRP spectral density limits for feeder link earth stations in the 17/24 GHz BSS. (a) This section applies to all applications for earth station licenses in the 17/24 GHz BSS frequency...
Code of Federal Regulations, 2010 CFR
2010-10-01
.... (a) Operators of NGSO MSS feeder link earth stations and GSO FSS earth stations in the band 29.25 to... MSS feeder link earth station complexes, that will minimize instances of unacceptable interference to the GSO FSS space stations. Earth station licensees operating with GSO FSS systems shall be capable of...
Code of Federal Regulations, 2012 CFR
2012-10-01
... feeder link earth stations in the 17/24 GHz BSS. 25.223 Section 25.223 Telecommunication FEDERAL....223 Off-axis EIRP spectral density limits for feeder link earth stations in the 17/24 GHz BSS. (a) This section applies to all applications for earth station licenses in the 17/24 GHz BSS frequency...
Code of Federal Regulations, 2014 CFR
2014-10-01
.... (a) Operators of NGSO MSS feeder link earth stations and GSO FSS earth stations in the band 29.25 to... MSS feeder link earth station complexes, that will minimize instances of unacceptable interference to the GSO FSS space stations. Earth station licensees operating with GSO FSS systems shall be capable of...
Code of Federal Regulations, 2013 CFR
2013-10-01
... Earth-to-space transmissions from feeder link earth station complexes. A “feeder link earth station complex” may include up to three (3) earth station groups, with each earth station group having up to four... NGSO MSS licensees or applicants pursuant to § 101.147. (b) A maximum of seven (7) feeder link earth...
Code of Federal Regulations, 2010 CFR
2010-10-01
... feeder link earth stations in the 17/24 GHz BSS. 25.223 Section 25.223 Telecommunication FEDERAL....223 Off-axis EIRP spectral density limits for feeder link earth stations in the 17/24 GHz BSS. (a) This section applies to all applications for earth station licenses in the 17/24 GHz BSS frequency...
USDA-ARS?s Scientific Manuscript database
The effect of feeding programs on the time of clearance of Escherichia coli in broiler breeder pullets was investigated. Broiler breeder pullets from a single grandparent flock were in ovo-vaccinated at 19 d of incubation with a vector HVT (vHVT) vector HVT + Infectious bursal disease (IBD) vaccine....
DOE Office of Scientific and Technical Information (OSTI.GOV)
Horowitz, Kelsey A; Ding, Fei; Mather, Barry A
The increasing deployment of distributed photovoltaic systems (DPV) can impact operations at the distribution level and the transmission level of the electric grid. It is important to develop and implement forward-looking approaches for calculating distribution upgrade costs that can be used to inform system planning, market and tariff design, cost allocation, and other policymaking as penetration levels of DPV increase. Using a bottom-up approach that involves iterative hosting capacity analysis, this report calculates distribution upgrade costs as a function of DPV penetration on three real feeders - two in California and one in the Northeastern United States.
Weber, E K; Stalder, K J; Patience, J F
2015-04-01
The study objectives were to determine nursery phase feeder space allowance effects on pig performance when double stocked and, second, to determine feeder space allowance and dried distillers grains with solubles (DDGS) inclusion level effects on pig performance and nutrient digestibility during the growing-finishing phase. This study was performed on the same group of pigs within a commercial wean-finish system. For the nursery phase, a completely randomized design was used to compare 3 feeder space allowance treatments (2.1, 2.5, and 2.9 cm/pig). A total of 3,720 pigs were randomly allotted to same-sex pens (10 feeders/treatment) housing 62 pigs/pen. Thirty 7-hole, double-sided feeders were utilized in the study. Differing linear feeder space treatments were established by blocking off sections for the nursery and grow-finish portions of this experiment. All pigs were provided equal floor space (0.26 m2/pig). In the grow-finish phase, a total of 1,860 pigs (n = 60 pens) were utilized in a 2 × 3 factorial design with 3 feeder space allowances (4.1, 4.9, or 5.7 cm/pig) and 2 dietary DDGS treatments (30% [D30] or 60% [D60]). Fecal and diet samples were collected and analyzed to estimate apparent total tract digestibility percentage (ATTD %). In the nursery portion of the trial, there was no feeder space treatment effect on ADG, ADFI, or feed efficiency (P > 0.10) from weaning to d 56 postweaning or during any weigh period. In the grow-finish portion of the trial, feeder space allowance and DDGS inclusion level did not affect ADG, ADFI, or feed efficiency (P > 0.05) from d 57 postweaning to market. Pigs fed the D30 diet had greater HCW, percent yield, and loin depth than those on the D60 diet (P < 0.05). Pigs fed the D30 treatment had greater (P < 0.05) ATTD for DM and GE for both collection periods compared with those on the D60 treatment. In summary, feeder space allowance did not impact pig performance during the nursery or grow-finish production phases. Inclusion of DDGS at higher levels will decrease ADFI but not ADG or efficiency when isocaloric diets are fed. The inclusion level of DDGS does impact HCW and percent yield because of increasing intestinal weights when pigs are fed diets containing increasing DDGS inclusion rates. Dry matter and energy digestibility were greater in pigs fed the lower DDGS treatment.
Verdú, M; Bach, A; Devant, M
2015-06-01
A total of 240 Holstein bulls (121 ± 2.0 kg initial BW; 99 ± 1.0 d of age), from 2 consecutive fattening cycles, were randomly allocated in 1 of 6 pens and assigned to 1 of the 3 treatments consisting of different concentrate feeder designs: a control feeder with 4 feeding spaces (CF), a feeder with less concentrate capacity (CFL), and a single-space feeder with lateral protections (SF). Each pen had a straw feeder and a drinker. All animals were fed a high-concentrate diet for ad libitum intake. Concentrate consumption was recorded daily using a computerized feeder, straw consumption was recorded weekly, and BW was recorded every 14 d. Animal behavior was registered on d 1, 3, 5, 8, and 14 and every 28 d by scan sampling. Eating behavior at concentrate feeders was filmed on d 12, 125, and 206. On d 7, 120, and 204, samples of rumen contents were collected for measurement of pH and VFA and blood samples were obtained to analyze NEFA, haptoglobin, glucose, and insulin. Animals were slaughtered after 223 d, and HCW and lesions of the rumen wall and liver were recorded. The accumulative concentrate consumption per animal tended (P = 0.09) to be greater with CF than with CFL and SF. Also, CV of concentrate consumption was greater (P < 0.01) for SF than for CF or CFL. However, feeder design did not influence the other performance and carcass data. Also, no differences among treatments in rumen wall evaluation and liver abscesses were observed. At 7 and 204 d of study, SF bulls had greater (P < 0.05) rumen pH compared with CF and CFL bulls. On d 7, the acetate to propionate ratio from SF was greater (P < 0.05) than for CFL or CF. At d 7, NEFA of SF were greater (P < 0.05) compared with CF and CFL. Bulls fed with CF have the greatest (P < 0.01) concentrate disappearance velocity followed by bulls fed with CFL and finally by bulls fed with SF, and this was associated with different feeding behaviors. Bulls on SF spent more time (P < 0.05) eating straw and exhibited fewer (P < 0.05) displacements at concentrate feeder than CF and CFL bulls. The CFL bulls exhibited (P < 0.01) more attempted mounts and tended (P = 0.10) to exhibit more completed mounts than CF bulls. In conclusion, both alternative feeder designs (CFL and SF) are good strategies to reduce total concentrate consumption without impairing performance, rumen health, or animal welfare in Holstein bulls fed high-concentrate diets. However, at the beginning, there was evidence that animals fed using SF had problems with adaptation.
Analysis of PV Advanced Inverter Functions and Setpoints under Time Series Simulation.
DOE Office of Scientific and Technical Information (OSTI.GOV)
Seuss, John; Reno, Matthew J.; Broderick, Robert Joseph
Utilities are increasingly concerned about the potential negative impacts distributed PV may have on the operational integrity of their distribution feeders. Some have proposed novel methods for controlling a PV system's grid - tie inverter to mitigate poten tial PV - induced problems. This report investigates the effectiveness of several of these PV advanced inverter controls on improving distribution feeder operational metrics. The controls are simulated on a large PV system interconnected at several locations within two realistic distribution feeder models. Due to the time - domain nature of the advanced inverter controls, quasi - static time series simulations aremore » performed under one week of representative variable irradiance and load data for each feeder. A para metric study is performed on each control type to determine how well certain measurable network metrics improve as a function of the control parameters. This methodology is used to determine appropriate advanced inverter settings for each location on the f eeder and overall for any interconnection location on the feeder.« less
NASA Astrophysics Data System (ADS)
Lee, Hyunah; Nam, Donggyu; Choi, Jae-Kyung; Araúzo-Bravo, Marcos J.; Kwon, Soon-Yong; Zaehres, Holm; Lee, Taehee; Park, Chan Young; Kang, Hyun-Wook; Schöler, Hans R.; Kim, Jeong Beom
2016-02-01
The maintenance of undifferentiated human pluripotent stem cells (hPSC) under xeno-free condition requires the use of human feeder cells or extracellular matrix (ECM) coating. However, human-derived sources may cause human pathogen contamination by viral or non-viral agents to the patients. Here we demonstrate feeder-free and xeno-free culture system for hPSC expansion using diffusion assisted synthesis-grown nanocrystalline graphene (DAS-NG), a synthetic non-biological nanomaterial which completely rule out the concern of human pathogen contamination. DAS-NG exhibited advanced biocompatibilities including surface nanoroughness, oxygen containing functional groups and hydrophilicity. hPSC cultured on DAS-NG could maintain pluripotency in vitro and in vivo, and especially cell adhesion-related gene expression profile was comparable to those of cultured on feeders, while hPSC cultured without DAS-NG differentiated spontaneously with high expression of somatic cell-enriched adhesion genes. This feeder-free and xeno-free culture method using DAS-NG will facilitate the generation of clinical-grade hPSC.
NASA Astrophysics Data System (ADS)
Funamoto, Daichi; Sugiura, Shinji
2017-02-01
Fungus-induced galls can attract spore-feeding arthropods as well as gall-feeding ones, resulting in diverse communities. Do large fungal galls support more abundant and diverse arthropod communities than small fungal galls? To address this question, we investigated the structure of the arthropod community associated with bud galls induced by the fungus Melanopsichium onumae on the tree species Cinnamomum yabunikkei (Lauraceae) in central Japan. Thirteen species of arthropods were associated with M. onumae galls. Dominant arthropod species were represented by the larvae of a salpingid beetle (a spore feeder), a nitidulid beetle (a spore feeder), a cosmopterigid moth (a spore feeder), an unidentified moth (a gall tissue feeder), and a drosophilid species (a gall tissue feeder). Arthropod abundance and species richness were positively correlated with gall diameter. The majority of the most abundant species were more frequently found in large galls than in small ones, indicating that large fungal galls, which have more food and/or space for arthropods, could support a more abundant and diverse arthropod community.
Baulu, J; Redmond, D E
1980-01-01
The behavioural profiles (time budgeting of social and nonsocial activities) and the frequencies of major social interactions of corral-enclosed rhesus monkeys were compared with sex- and age-matched free-ranging rhesus monkeys on La Cueva Island, Puerto Rico. All animals (n = 32) were provisioned ad libitum at specific feeder sites. The occurrence of 14 behaviours around feeders was compared with their occurrence away from the feeders by noting the location of each monkey relative to the feeder at the time of observation. An analysis of variance between free-ranging versus corral-enclosed groups and within groups by location (around or away from the feeder) revealed significant differences in several behavioural categories, including foraging, lookout, inactive, dominant, submissive, allogrooming, social contact, social initiative, active, and passive behaviours. When the effect of limited food distribution sites was analyzed by comparing data recorded away from the feeding sites, there were remarkably few differences between the groups.
A new angle on microscopic suspension feeders near boundaries.
Pepper, Rachel E; Roper, Marcus; Ryu, Sangjin; Matsumoto, Nobuyoshi; Nagai, Moeto; Stone, Howard A
2013-10-15
Microscopic sessile suspension feeders are a critical component in aquatic ecosystems, acting as an intermediate trophic stage between bacteria and higher eukaryotic taxa. Because they live attached to boundaries, it has long been thought that recirculation of the feeding currents produced by sessile suspension feeders inhibits their ability to access fresh fluid. However, previous models for the feeding flows of these organisms assume that they feed by pushing fluid perpendicular to surfaces they live upon, whereas we observe that sessile suspension feeders often feed at an angle to these boundaries. Using experiments and calculations, we show that living suspension feeders (Vorticella) likely actively regulate the angle that they feed relative to a substratum. We then use theory and simulations to show that angled feeding increases nutrient and particle uptake by reducing the reprocessing of depleted water. This work resolves an open question of how a key class of suspension-feeding organisms escapes physical limitations associated with their sessile lifestyle. Copyright © 2013 Biophysical Society. Published by Elsevier Inc. All rights reserved.
Nutrient compensatory foraging in a free-living social insect
NASA Astrophysics Data System (ADS)
Christensen, Keri L.; Gallacher, Anthony P.; Martin, Lizzie; Tong, Desmond; Elgar, Mark A.
2010-10-01
The geometric framework model predicts that animal foraging decisions are influenced by their dietary history, with animals targeting a combination of essential nutrients through compensatory foraging. We provide experimental confirmation of nutrient-specific compensatory foraging in a natural, free-living population of social insects by supplementing their diet with sources of protein- or carbohydrate-rich food. Colonies of the ant Iridomyrmex suchieri were provided with feeders containing food rich in either carbohydrate or protein for 6 days, and were then provided with a feeder containing the same or different diet. The patterns of recruitment were consistent with the geometric framework: while feeders with a carbohydrate diet typically attracted more workers than did feeders with protein diet, the difference in recruitment between the two nutrients was smaller if the colonies had had prior access to carbohydrate than protein. Further, fewer ants visited feeders if the colony had had prior access to protein than to carbohydrates, suggesting that the larvae play a role in worker foraging behaviour.
Jadcherla, Sudarshan R.; Stoner, Erin; Gupta, Alankar; Bates, D. Gregory; Fernandez, Soledad; Di Lorenzo, Carlo; Linscheid, Thomas
2013-01-01
Background and objectives Abnormal swallowing (dysphagia) among neonates is commonly evaluated using the videofluoroscopic swallow study (VSS). Radiological findings considered high risk for administration of oral feeding include nasopharyngeal reflux, laryngeal penetration, aspiration, or pooling. Our aims were to determine pharyngoesophageal motility correlates in neonates with dysphagia and the impact of multidisciplinary feeding strategy. Methods Twenty dysphagic neonates (mean gestation ± standard deviation [SD] = 30.9 ± 4.9 weeks; median 31.1 weeks; range = 23.7–38.6 weeks) with abnormal VSS results were evaluated at 49.9 ± 16.5 weeks (median 41.36 weeks) postmenstrual age. The subjects underwent a swallow-integrated pharyngoesophageal motility assessment of basal and adaptive swallowing reflexes using a micromanometry catheter and pneumohydraulic water perfusion system. Based on observations during the motility study, multidisciplinary feeding strategies were applied and included postural adaptation, sensory modification, hunger manipulation, and operant conditioning methods. To discriminate pharyngoesophageal manometry correlates between oral feeders and tube feeders, data were stratified based on the primary feeding method at discharge, oral feeding versus tube feeding. Results At discharge, 15 of 20 dysphagic neonates achieved oral feeding success, and the rest required chronic tube feeding. Pharyngoesophageal manometry correlates were significantly different (P <0.05) between the primary oral feeders versus the chronic tube feeders for swallow frequency, swallow propagation, presence of adaptive peristaltic reflexes, oral feeding challenge test results, and upper esophageal sphincter tone. VSS results or disease characteristics had little effect on the feeding outcomes (P = NS). Conclusions Swallow-integrated esophageal motility studies permit prolonged evaluation of swallowing reflexes and responses to stimuli under controlled conditions at cribside. The dysfunctional neuromotor mechanisms may be responsible for neonatal dysphagia or its consequences. Manometry may be a better predictor than VSS in identifying patients who are likely to succeed in vigorous intervention programs. PMID:19179881
Object categorization by wild ranging birds-Winter feeder experiments.
Nováková, Nela; Veselý, Petr; Fuchs, Roman
2017-10-01
The object categorization is only scarcely studied using untrained wild ranging animals and relevant stimuli. We tested the importance of the spatial position of features salient for categorization of a predator using wild ranging birds (titmice) visiting a winter feeder. As a relevant stimulus we used a dummy of a raptor, the European sparrowhawk (Accipiter nisus), placed at the feeding location. This dummy was designed to be dismantled into three parts and rearranged with the head in the correct position, in the middle or at the bottom of the dummy. When the birds had the option of visiting an alternative feeder with a dummy pigeon, they preferred this option to visiting the feeder with the dummy sparrowhawk with the head in any of the three positions. When the birds had the option of visiting an alternative feeder with an un-rearranged dummy sparrowhawk, they visited both feeders equally often, and very scarcely. This suggests that the titmice considered all of the sparrowhawk modifications as being dangerous, and equally dangerous as the un-rearranged sparrowhawk. The position of the head was not the most important cue for categorization. The presence of the key features was probably sufficient for categorization, and their mutual spatial position was of lower importance. Copyright © 2017 Elsevier B.V. All rights reserved.
An In-Rush Current Suppression Technique for the Solid-State Transfer Switch System
NASA Astrophysics Data System (ADS)
Cheng, Po-Tai; Chen, Yu-Hsing
More and more utility companies provide dual power feeders as a premier service of high power quality and reliability. To take advantage of this, the solid-state transfer switch (STS) is adopted to protect the sensitive load against the voltage sag. However, the fast transfer process may cause in-rush current on the load-side transformer due to the resulting DC-offset in its magnetic flux as the load-transfer is completed. The in-rush current can reach 2∼6 p.u. and it may trigger the over-current protections on the power feeder. This paper develops a flux estimation scheme and a thyristor gating scheme based on the impulse commutation bridge STS (ICBSTS) to minimize the DC-offset on the magnetic flux. By sensing the line voltages of both feeders, the flux estimator can predict the peak transient flux linkage at the moment of load-transfer and evaluate a suitable moment for the transfer to minimize the in-rush current. Laboratory test results are presented to validate the performance of the proposed system.
NASA Astrophysics Data System (ADS)
Rahman, Yuli Asmi; Manjang, Salama; Yusran, Ilham, Amil Ahmad
2018-03-01
Power loss minimization have many advantagess to the distribution system radial among others reduction of power flow in feeder lines, freeing stress on feeder loading, deterrence of power procurement from the grid and also the cost of loss compensating instruments. This paper, presents capacitor and photovoltaic (PV) placement as alternative means to decrease power system losses. The paper aims to evaluate the best alternative for decreasing power system losses and improving voltage profile in the radial distribution system. To achieve the objectives of paper, they are used three cases tested by Electric Transient and Analysis Program (ETAP) simulation. Firstly, it performs simulation of placement capacitor. Secondly, simulated placement of PV. Lastly, it runs simulation of placement capacitor and PV simultaneously. The simulations were validated using the IEEE 34-bus test system. As a result, they proved that the installation of capacitor and PV integration simultaneously leading to voltage profile correction and power losses minimization significantly.
Customer Engagement in AEP gridSMART Residential Transactive System
DOE Office of Scientific and Technical Information (OSTI.GOV)
Widergren, Steven E.; Marinovici, Maria C.; Fuller, Jason C.
— In 2013, AEP Ohio (AEP) operated a 5-minute real-time price (RTP) electricity market system on 4 distribution feeders as part of their gridSMART® demonstration project. The RTP households were billed for their electricity usage according to an RTP tariff approved by the Public Utility Commission of Ohio. They were given the incentive that their annual bill would be no greater than if they were on the flat-rate tariff, but they had financial incentives to shift consumption from high price periods to low price periods. Incentives were also available for response under high prices from local events, such as reachingmore » the distribution feeder capacity or a critical peak pricing event. An analysis of this transactive system experiment was completed in early 2014. This paper describes the incentive provided to the customer, the nature of their interaction with the smart thermostat that provided automated response to the transactive signal, and their level of satisfaction with the program.« less
Effects of diet form and feeder adjustment on growth performance of nursery and finishing pigs.
Nemechek, J E; Tokach, M D; Dritz, S S; Fruge, E D; Hansen, E L; Goodband, R D; DeRouchey, J M; Woodworth, J C
2015-08-01
Three experiments were conducted to determine the effects of feeder adjustment and diet form on growth performance of nursery (Exp. 1 and 2) and finishing (Exp. 3) pigs. Treatments were arranged as a 2 × 3 factorial with the main effects of feeder adjustment and diet form. The 2 feeder adjustments were a narrow and wide feeder adjustment (minimum gap opening of 1.27 and 2.54 cm, respectively). The 3 diet forms were meal, poor-quality pellets (70% pellets and 30% fines for Exp. 1 and 2 and 50% pellets and 50% fines for Exp. 3), and screened pellets with minimal fines (3 to 10%). In Exp. 1, 210 pigs (initially 11.9 kg BW) were used in a 21-d trial with 7 pigs per pen and 5 pens per treatment. No feeder adjustment × diet form interactions were observed. There were no differences in ADG, ADFI, or G:F due to feeder adjustment. Pigs fed the meal diet had increased ( < 0.05) ADG and ADFI compared with pigs fed the poor-quality or screened pellets. Pigs fed meal or poor-quality pellets had decreased ( < 0.05) G:F compared with pigs fed screened pellets. In Exp. 2, 1,005 nursery pigs (initially 14.1 kg BW) were used in a 28-d trial with 26 to 28 pigs per pen and 6 pens per treatment. Pigs fed from the narrow feeder adjustment had decreased ( < 0.05) ADG and ADFI compared with pigs fed from the wide adjustment with no differences in G:F. Pigs fed the meal diet had decreased ( < 0.05) ADG compared with pigs fed poor-quality or screened pellets. Pigs fed meal or poor-quality pellets had decreased ( < 0.05) G:F compared with pigs fed screened pellets. In Exp. 3, 246 pigs (initially 56.8 kg BW) were used in a 69-d trial with 5 pens per treatment and 6 or 7 pigs per pen. Overall, ADFI decreased ( < 0.05) and G:F increased ( < 0.05) for pigs fed from the narrow adjusted feeders compared with the wide adjustment with no differences in ADG. Overall, pigs fed meal diets tended to have decreased ( < 0.10) ADG and had decreased ( < 0.05) G:F compared with pigs fed screened pellets; ADG and G:F in those fed poor-quality pellets were intermediate. Feeding meal or poor-quality pellets increased ( < 0.05) ADFI compared with pigs fed screened pellets. In conclusion, feeding nursery pigs from a wide feeder gap may increase ADG and ADFI with no negative effects on G:F. For finishing pigs, reducing feeder gap reduced feed disappearance and improved G:F. In all experiments, the greatest G:F improvements from pelleting were observed when the percentage of fines was minimized.
A Quasi-Periodic Linear Feeder for the Impurity Granular Injection on DIII-D
DOE Office of Scientific and Technical Information (OSTI.GOV)
Nagy, Alex; Bortolon, A.; Brown, W.
Injection of solid nonfuel pellets has been actively used as a tool for pacing and mitigation of edge localized modes (ELMs). In DIII-D, effective ELM pacing has been demonstrated by the high-frequency injection of lithium and carbon submillimeter spheres, using the impurity granule injector (IGI). This device injects granules into the plasma at speeds up to 150 m/s, through impact with a rotating impeller. In the IGI, high-frequency granule delivery was accomplished through a vibrational granule dropper, in which high time-average rates are obtained at the cost of lack of period control. Here, we present a new in-line granule feeder,more » capable of delivering granules of size 0.2-2 mm with no restriction of material properties, at quasi-periodic rates of up to 150 Hz, for 0.7-mm diameter lithium granules (600 Hz using 0.3-mm granules). The new dropper mechanism combines two piezo-in-line units; one which feeds the impeller and one which circulates granules that are filtered out of the feeder path. A remotely adjustable filter eliminates granules that are stacked, oversized, or side by side allowing the formation of a single moving granule injection line. The granules fall off the in-line feeder exit one at a time, achieving a quasi-periodic delivery rate proportional to the exit speed. At higher rates, the periodicity deteriorates. This behavior was studied using high-speed cameras and electrostatic measurements, and it was found that at drop rates <60 Hz, the granule delivery period has a variation of ±25% which appears to be caused by gaps which develop in the last centimeter of the injection line, as granules exit off the moving track. The linear feeder concept is robust against bridge instabilities and clogging issues, thanks to the simple diverter filter and constant recirculation of granules. Furthermore, the open-top design of the device facilitates refilling the device from separate reservoirs and has easy access for directly monitoring operation and adjustment. This paper describes the details of the in-line feeder design, along with several design iterations. The goal is a robust in-vacuum mechanism that can deliver granule flow ranging from a single particle to a line of particles at 150 per second, using different sizes and materials from the same apparatus.« less
A Quasi-Periodic Linear Feeder for the Impurity Granular Injection on DIII-D
Nagy, Alex; Bortolon, A.; Brown, W.; ...
2018-04-10
Injection of solid nonfuel pellets has been actively used as a tool for pacing and mitigation of edge localized modes (ELMs). In DIII-D, effective ELM pacing has been demonstrated by the high-frequency injection of lithium and carbon submillimeter spheres, using the impurity granule injector (IGI). This device injects granules into the plasma at speeds up to 150 m/s, through impact with a rotating impeller. In the IGI, high-frequency granule delivery was accomplished through a vibrational granule dropper, in which high time-average rates are obtained at the cost of lack of period control. Here, we present a new in-line granule feeder,more » capable of delivering granules of size 0.2-2 mm with no restriction of material properties, at quasi-periodic rates of up to 150 Hz, for 0.7-mm diameter lithium granules (600 Hz using 0.3-mm granules). The new dropper mechanism combines two piezo-in-line units; one which feeds the impeller and one which circulates granules that are filtered out of the feeder path. A remotely adjustable filter eliminates granules that are stacked, oversized, or side by side allowing the formation of a single moving granule injection line. The granules fall off the in-line feeder exit one at a time, achieving a quasi-periodic delivery rate proportional to the exit speed. At higher rates, the periodicity deteriorates. This behavior was studied using high-speed cameras and electrostatic measurements, and it was found that at drop rates <60 Hz, the granule delivery period has a variation of ±25% which appears to be caused by gaps which develop in the last centimeter of the injection line, as granules exit off the moving track. The linear feeder concept is robust against bridge instabilities and clogging issues, thanks to the simple diverter filter and constant recirculation of granules. Furthermore, the open-top design of the device facilitates refilling the device from separate reservoirs and has easy access for directly monitoring operation and adjustment. This paper describes the details of the in-line feeder design, along with several design iterations. The goal is a robust in-vacuum mechanism that can deliver granule flow ranging from a single particle to a line of particles at 150 per second, using different sizes and materials from the same apparatus.« less
A longitudinal study of Salmonella from snakes used in a public outreach program.
Goupil, Brad A; Trent, Ava M; Bender, Jeff; Olsen, Karen E; Morningstar, Brenda R; Wünschmann, Arno
2012-12-01
Snakes are considered to be a source of Salmonella infection for humans, but little is known about the actual serotype prevalence in healthy snakes over time. Twelve snakes involved in a public outreach program, representing seven different species, were tested weekly for shedding of Salmonella sp. over a period of 10 consecutive weeks. The snakes were housed in close proximity but in separate exhibits. Fresh fecal samples (when available) or cloacal swabs were cultured for Salmonella sp., and subsequent Salmonella isolates were serotyped. As representatives of the feed source, the feces of two mice and the intestines of one rat were cultured weekly. Fecal samples from 11 of the 12 snakes were positive for Salmonella at least once. Seven (58%) of 12 snakes were culture positive five times or more. The weekly prevalence of Salmonella shedding varied between 25% and 66%. Two or more different serotypes were isolated from nine snakes over time; however, a predominant serotype was generally isolated from each of these snakes. Altogether 15 different serotypes were identified. Serotypes of public health concern included Newport, Oranienburg, and Muenchen. Two samples from feeder rodents were positive for Salmonella. The results are consistent with previous studies showing high intestinal colonization rates with Salmonella sp. in snakes. Frequent and intermittent shedding of multiple serotypes was evident. Feeder rodents might serve as a source for intestinal colonization. Appropriate handling protocols should be implemented for all reptiles associated with public outreach programs to minimize risk of Salmonella transmission to the public.
Can rats solve a simple version of the traveling salesman problem?
Bures, J; Buresová, O; Nerad, L
1992-12-31
Whereas correct tours through the radial arm maze are almost equally long, free choice mazes with multiple goals scattered in an open field allow the animal to select the shortest one from a multitude of correct tours. Thirteen rats were trained (at 10 trials per day) to visit an array of cylindrical feeders in an open field (40 x 100 cm) with reward available only when visiting the last feeder of the set. In Expt. 1 with eight feeders arranged in five different configurations the rats made after 10 days of training 1 error in the first 8 choices and incidence of errorless trials was about 20%. In Expt. 2. the use of six feeders in a rectangular (A) or double triangle (B) configuration increased the incidence of errorless trials to 60%. Expt. 3 showed that performance in the 6-feeder maze was significantly impaired by 6 mg/kg ketamine or 0.25 mg/kg scopolamine but not by lower dosages of these drugs. Tours generated on errorless trials (each feeder visited only once) during 10 days of Expt. 2 were analyzed. Six places can be visited in 6! = 720 different closed tours the lengths of which (in arbitrary units) range from 6.00 to 10.12 for A and from 6.83 to 10.47 for B. Whereas random generation of correct routes yielded only 5% of the shortest tours, they were clearly preferred by rats (41% in A and 45% in B). The apparent proficiency of rats in this optimization problem is probably not due to cognitive comparison of the possible correct routes but rather to following a simple rule 'Always go to the nearest not yet visited feeder'.
On Distributed PV Hosting Capacity Estimation, Sensitivity Study, and Improvement
DOE Office of Scientific and Technical Information (OSTI.GOV)
Ding, Fei; Mather, Barry
This paper first studies the estimated distributed PV hosting capacities of seventeen utility distribution feeders using the Monte Carlo simulation based stochastic analysis, and then analyzes the sensitivity of PV hosting capacity to both feeder and photovoltaic system characteristics. Furthermore, an active distribution network management approach is proposed to maximize PV hosting capacity by optimally switching capacitors, adjusting voltage regulator taps, managing controllable branch switches and controlling smart PV inverters. The approach is formulated as a mixed-integer nonlinear optimization problem and a genetic algorithm is developed to obtain the solution. Multiple simulation cases are studied and the effectiveness of themore » proposed approach on increasing PV hosting capacity is demonstrated.« less
Code of Federal Regulations, 2014 CFR
2014-10-01
... 47 Telecommunication 2 2014-10-01 2014-10-01 false Sharing between NGSO MSS Feeder links Earth....250 Sharing between NGSO MSS Feeder links Earth Stations in the 19.3-19.7 GHz and 29.1-29.5 GHz Bands. (a) NGSO MSS applicants shall be licensed to operate in the 29.1-29.5 GHz band for Earth-to-space...
Code of Federal Regulations, 2013 CFR
2013-10-01
... 47 Telecommunication 2 2013-10-01 2013-10-01 false Sharing between NGSO MSS Feeder links Earth....250 Sharing between NGSO MSS Feeder links Earth Stations in the 19.3-19.7 GHz and 29.1-29.5 GHz Bands. (a) NGSO MSS applicants shall be licensed to operate in the 29.1-29.5 GHz band for Earth-to-space...
Code of Federal Regulations, 2012 CFR
2012-10-01
... 47 Telecommunication 2 2012-10-01 2012-10-01 false Sharing between NGSO MSS Feeder links Earth....250 Sharing between NGSO MSS Feeder links Earth Stations in the 19.3-19.7 GHz and 29.1-29.5 GHz Bands. (a) NGSO MSS applicants shall be licensed to operate in the 29.1-29.5 GHz band for Earth-to-space...
Code of Federal Regulations, 2010 CFR
2010-10-01
... 47 Telecommunication 2 2010-10-01 2010-10-01 false Sharing between NGSO MSS Feeder links Earth....250 Sharing between NGSO MSS Feeder links Earth Stations in the 19.3-19.7 GHz and 29.1-29.5 GHz Bands. (a) NGSO MSS applicants shall be licensed to operate in the 29.1-29.5 GHz band for Earth-to-space...
Code of Federal Regulations, 2011 CFR
2011-10-01
... 47 Telecommunication 2 2011-10-01 2011-10-01 false Sharing between NGSO MSS Feeder links Earth....250 Sharing between NGSO MSS Feeder links Earth Stations in the 19.3-19.7 GHz and 29.1-29.5 GHz Bands. (a) NGSO MSS applicants shall be licensed to operate in the 29.1-29.5 GHz band for Earth-to-space...
30 CFR 75.1001 - Overcurrent protection.
Code of Federal Regulations, 2011 CFR
2011-07-01
... MANDATORY SAFETY STANDARDS-UNDERGROUND COAL MINES Trolley Wires and Trolley Feeder Wires § 75.1001 Overcurrent protection. [Statutory Provisions] Trolley wires and trolley feeder wires shall be provided with...
30 CFR 75.1001 - Overcurrent protection.
Code of Federal Regulations, 2010 CFR
2010-07-01
... MANDATORY SAFETY STANDARDS-UNDERGROUND COAL MINES Trolley Wires and Trolley Feeder Wires § 75.1001 Overcurrent protection. [Statutory Provisions] Trolley wires and trolley feeder wires shall be provided with...
30 CFR 75.1000 - Cutout switches.
Code of Federal Regulations, 2011 CFR
2011-07-01
... MANDATORY SAFETY STANDARDS-UNDERGROUND COAL MINES Trolley Wires and Trolley Feeder Wires § 75.1000 Cutout switches. [Statutory Provisions] Trolley wires and trolley feeder wires, shall be provided with cutout...
30 CFR 75.1000 - Cutout switches.
Code of Federal Regulations, 2010 CFR
2010-07-01
... MANDATORY SAFETY STANDARDS-UNDERGROUND COAL MINES Trolley Wires and Trolley Feeder Wires § 75.1000 Cutout switches. [Statutory Provisions] Trolley wires and trolley feeder wires, shall be provided with cutout...
Real time testing of intelligent relays for synchronous distributed generation islanding detection
NASA Astrophysics Data System (ADS)
Zhuang, Davy
As electric power systems continue to grow to meet ever-increasing energy demand, their security, reliability, and sustainability requirements also become more stringent. The deployment of distributed energy resources (DER), including generation and storage, in conventional passive distribution feeders, gives rise to integration problems involving protection and unintentional islanding. Distributed generators need to be islanded for safety reasons when disconnected or isolated from the main feeder as distributed generator islanding may create hazards to utility and third-party personnel, and possibly damage the distribution system infrastructure, including the distributed generators. This thesis compares several key performance indicators of a newly developed intelligent islanding detection relay, against islanding detection devices currently used by the industry. The intelligent relay employs multivariable analysis and data mining methods to arrive at decision trees that contain both the protection handles and the settings. A test methodology is developed to assess the performance of these intelligent relays on a real time simulation environment using a generic model based on a real-life distribution feeder. The methodology demonstrates the applicability and potential advantages of the intelligent relay, by running a large number of tests, reflecting a multitude of system operating conditions. The testing indicates that the intelligent relay often outperforms frequency, voltage and rate of change of frequency relays currently used for islanding detection, while respecting the islanding detection time constraints imposed by standing distributed generator interconnection guidelines.
Distribution Feeder Modeling for Time-Series Simulation of Voltage Management Strategies: Preprint
DOE Office of Scientific and Technical Information (OSTI.GOV)
Giraldez Miner, Julieta I; Gotseff, Peter; Nagarajan, Adarsh
This paper presents techniques to create baseline distribution models using a utility feeder from Hawai'ian Electric Company. It describes the software-to-software conversion, steady-state, and time-series validations of a utility feeder model. It also presents a methodology to add secondary low-voltage circuit models to accurately capture the voltage at the customer meter level. This enables preparing models to perform studies that simulate how customer-sited resources integrate into legacy utility distribution system operations.
Jafari, Mahtab
2018-02-01
Within the coming decade, the demand for well-trained pharmacists is expected to only increase, especially with the aging of the United States (US) population. To help fill this growing demand, the University of California, Irvine (UCI) aims to offer a unique pre-pharmacy degree program and has developed a Bachelor of Science (BS) degree in Pharmaceutical Sciences to help achieve this goal. In this commentary, we share our experience with our curriculum and highlight its features in an effort to encourage other institutions to enhance the learning experience of their pre-pharmacy students. The efforts of the UCI Department of Pharmaceutical Sciences has resulted in UCI being consistently ranked as one of the top feeder institutions by the Pharmacy College Application Service (PharmCAS) in recent years. The UCI Pharmaceutical Sciences Bachelor of Science offers a unique pre-pharmacy educational experience in an effort to better prepare undergraduates for the rigors of the doctorate of pharmacy curriculum. Copyright © 2017. Published by Elsevier Inc.
Yamashita, Tomoko; Miyamoto, Yuki; Bando, Yoshio; Ono, Takashi; Kobayashi, Sakurako; Doi, Ayano; Araki, Toshihiro; Kato, Yosuke; Shirakawa, Takayuki; Suzuki, Yutaka; Yamauchi, Junji; Yoshida, Shigetaka; Sato, Naoya
2017-01-01
Oligodendrocytes myelinate axons and form myelin sheaths in the central nervous system. The development of therapies for demyelinating diseases, including multiple sclerosis and leukodystrophies, is a challenge because the pathogenic mechanisms of disease remain poorly understood. Primate pluripotent stem cell-derived oligodendrocytes are expected to help elucidate the molecular pathogenesis of these diseases. Oligodendrocytes have been successfully differentiated from human pluripotent stem cells. However, it is challenging to prepare large amounts of oligodendrocytes over a short amount of time because of manipulation difficulties under conventional primate pluripotent stem cell culture methods. We developed a proprietary dissociated monolayer and feeder-free culture system to handle pluripotent stem cell cultures. Because the dissociated monolayer and feeder-free culture system improves the quality and growth of primate pluripotent stem cells, these cells could potentially be differentiated into any desired functional cells and consistently cultured in large-scale conditions. In the current study, oligodendrocyte progenitor cells and mature oligodendrocytes were generated within three months from monkey embryonic stem cells. The embryonic stem cell-derived oligodendrocytes exhibited in vitro myelinogenic potency with rat dorsal root ganglion neurons. Additionally, the transplanted oligodendrocyte progenitor cells differentiated into myelin basic protein-positive mature oligodendrocytes in the mouse corpus callosum. This preparative method was used for human induced pluripotent stem cells, which were also successfully differentiated into oligodendrocyte progenitor cells and mature oligodendrocytes that were capable of myelinating rat dorsal root ganglion neurons. Moreover, it was possible to freeze, thaw, and successfully re-culture the differentiating cells. These results showed that embryonic stem cells and human induced pluripotent stem cells maintained in a dissociated monolayer and feeder-free culture system have the potential to generate oligodendrocyte progenitor cells and mature oligodendrocytes in vitro and in vivo. This culture method could be applied to prepare large amounts of oligodendrocyte progenitor cells and mature oligodendrocytes in a relatively short amount of time.
24 CFR 3280.803 - Power supply.
Code of Federal Regulations, 2011 CFR
2011-04-01
... 24 Housing and Urban Development 5 2011-04-01 2011-04-01 false Power supply. 3280.803 Section 3280... DEVELOPMENT MANUFACTURED HOME CONSTRUCTION AND SAFETY STANDARDS Electrical Systems § 3280.803 Power supply. (a) The power supply to the manufactured home shall be a feeder assembly consisting of not more than one...
21 CFR 520.1448a - Monensin blocks.
Code of Federal Regulations, 2011 CFR
2011-04-01
...) Limitations. Block to be fed free choice to pasture cattle (slaughter, stocker, feeder, and dairy and beef.... Blocks to be fed free choice to pasture cattle (slaughter, stocker, feeder, and dairy and beef...
11. MOVABLE BED SEDIMENTATION MODELS. AUTOMATIC SEDIMENT FEEDER DESIGNED AND ...
11. MOVABLE BED SEDIMENTATION MODELS. AUTOMATIC SEDIMENT FEEDER DESIGNED AND BUILT BY WES. - Waterways Experiment Station, Hydraulics Laboratory, Halls Ferry Road, 2 miles south of I-20, Vicksburg, Warren County, MS
DOE Office of Scientific and Technical Information (OSTI.GOV)
Allehyani, Ahmed; Beshir, Mohammed
Voltage regulators help maintain an acceptable voltage profile for the system. This paper discusses the effect of installing voltage regulators to the system to fix the voltage drop resulting from the electrical vehicles loading increase when they are being charged. The effect will be studied in the afternoon, when the peak load occurs, using the IEEE 34 bus test feeder. First, only one spot node is used to charge the electric vehicles while a voltage regulator is present. Second, five spot nodes are loaded at the same time to charge the electric vehicles while voltage regulators are installed at eachmore » node. After that, the impact of electric vehicles on distribution feeders that do not have voltage regulators will appear.« less
Characterization of vibrissa germinative cells: transition of cell types.
Osada, A; Kobayashi, K
2001-12-01
Germinative cells, small cell masses attached to the stalks of dermal papillae that are able to differentiate into the hair shaft and inner root sheath, form follicular bulb-like structures when co-cultured with dermal papilla cells. We studied the growth characteristics of germinative cells to determine the cell types in the vibrissa germinative tissue. Germinative tissues, attaching to dermal papillae, were cultured on 3T3 feeder layers. The cultured keratinocytes were harvested and transferred, equally and for two passages, onto lined dermal papilla cells (LDPC) and/or 3T3 feeder layers. The resulting germinative cells were classified into three types in the present experimental condition. Type 1 cells grow very well on either feeder layer, whereas Type 3 cells scarcely grow on either feeder layer. Type 2 cells are very conspicuous and are reversible. They grow well on 3T3 but growth is suppressed on LDPC feeder layers. The Type 2 cells that grow well on 3T3 feeder layers, however, are suppressed when transferred onto LDPC and the Type 2 cells that are suppressed on LDPC begin to grow again on 3T3. The transition of one cell type to another in vitro and the cell types that these germinative cell types correspond to in vivo is discussed. It was concluded that stem cells or their close progenitors reside in the germinative tissues of the vibrissa bulb except at late anagen-early catagen.
Multiple Antenna Implementation System (MAntIS)
DOE Office of Scientific and Technical Information (OSTI.GOV)
Carter, M.D.; Batchelor, D.B.; Jaeger, E.F.
1993-01-01
The MAntIS code was developed as an aid to the design of radio frequency (RF) antennas for fusion applications. The code solves for the electromagnetic fields in three dimensions near the antenna structure with a realistic plasma load. Fourier analysis is used in the two dimensions that are tangential to the plasma surface and backwall. The third dimension is handled analytically in a vacuum region with a general impedance match at the plasma-vacuum interface. The impedance tensor is calculated for a slab plasma using the ORION-lD code with all three electric field components included and warm plasma corrections. The codemore » permits the modeling of complicated antenna structures by superposing currents that flow on the surfaces of rectangular parallelepipeds. Specified current elements have feeders that continuously connect the current flowing from the ends of the strap to the feeders. The elements may have an arbitrary orientation with respect to the static magnetic field. Currents are permitted to vary along the length of the current strap and feeders. Parameters that describe this current variation can be adjusted to approximately satisfy boundary conditions on the current elements. The methods used in MAntIS and results for a primary loop antenna design are presented.« less
Yanagimachi, Masakatsu D.; Niwa, Akira; Tanaka, Takayuki; Honda-Ozaki, Fumiko; Nishimoto, Seiko; Murata, Yuuki; Yasumi, Takahiro; Ito, Jun; Tomida, Shota; Oshima, Koichi; Asaka, Isao; Goto, Hiroaki; Heike, Toshio; Nakahata, Tatsutoshi; Saito, Megumu K.
2013-01-01
Monocytic lineage cells (monocytes, macrophages and dendritic cells) play important roles in immune responses and are involved in various pathological conditions. The development of monocytic cells from human embryonic stem cells (ESCs) and induced pluripotent stem cells (iPSCs) is of particular interest because it provides an unlimited cell source for clinical application and basic research on disease pathology. Although the methods for monocytic cell differentiation from ESCs/iPSCs using embryonic body or feeder co-culture systems have already been established, these methods depend on the use of xenogeneic materials and, therefore, have a relatively poor-reproducibility. Here, we established a robust and highly-efficient method to differentiate functional monocytic cells from ESCs/iPSCs under serum- and feeder cell-free conditions. This method produced 1.3×106±0.3×106 floating monocytes from approximately 30 clusters of ESCs/iPSCs 5–6 times per course of differentiation. Such monocytes could be differentiated into functional macrophages and dendritic cells. This method should be useful for regenerative medicine, disease-specific iPSC studies and drug discovery. PMID:23573196
Complex memories in honeybees: can there be more than two?
Reinhard, Judith; Srinivasan, Mandyam V; Zhang, Shaowu
2006-04-01
Foraging honeybees are likely to learn visual and chemical cues associated with many different food sources. Here, we explore how many such sources can be memorized and recalled. Marked bees were trained to visit two (or three) sugar feeders, each placed at a different outdoor location and carrying a different scent. We then tested the ability of the bees to recall these locations and fly to them, when the training scents were blown into the hive, and the scents and food at the feeders were removed. When trained on two feeder locations, each associated with a different scent, the bees could correctly recall the location associated with each scent. However, this ability broke down when the number of scents and feeder locations was increased to three. Performance was partially restored when each of the three training feeders was endowed with an additional cue, namely, a distinct colour. Our results suggest that bees can recall a maximum of two locations when each is associated with a different scent. However, this number can be increased if the scent cues are augmented by visual cues. These findings have implications for the ways in which associations are established and laid down in honeybee memory.
Optic flow informs distance but not profitability for honeybees.
Shafir, Sharoni; Barron, Andrew B
2010-04-22
How do flying insects monitor foraging efficiency? Honeybees (Apis mellifera) use optic flow information as an odometer to estimate distance travelled, but here we tested whether optic flow informs estimation of foraging costs also. Bees were trained to feeders in flight tunnels such that bees experienced the greatest optic flow en route to the feeder closest to the hive. Analyses of dance communication showed that, as expected, bees indicated the close feeder as being further, but they also indicated this feeder as the more profitable, and preferentially visited this feeder when given a choice. We show that honeybee estimates of foraging cost are not reliant on optic flow information. Rather, bees can assess distance and profitability independently and signal these aspects as separate elements of their dances. The optic flow signal is sensitive to the nature of the environment travelled by the bee, and is therefore not a good index of flight energetic costs, but it provides a good indication of distance travelled for purpose of navigation and communication, as long as the dancer and recruit travel similar routes. This study suggests an adaptive dual processing system in honeybees for communicating and navigating distance flown and for evaluating its energetic costs.
Optic flow informs distance but not profitability for honeybees
Shafir, Sharoni; Barron, Andrew B.
2010-01-01
How do flying insects monitor foraging efficiency? Honeybees (Apis mellifera) use optic flow information as an odometer to estimate distance travelled, but here we tested whether optic flow informs estimation of foraging costs also. Bees were trained to feeders in flight tunnels such that bees experienced the greatest optic flow en route to the feeder closest to the hive. Analyses of dance communication showed that, as expected, bees indicated the close feeder as being further, but they also indicated this feeder as the more profitable, and preferentially visited this feeder when given a choice. We show that honeybee estimates of foraging cost are not reliant on optic flow information. Rather, bees can assess distance and profitability independently and signal these aspects as separate elements of their dances. The optic flow signal is sensitive to the nature of the environment travelled by the bee, and is therefore not a good index of flight energetic costs, but it provides a good indication of distance travelled for purpose of navigation and communication, as long as the dancer and recruit travel similar routes. This study suggests an adaptive dual processing system in honeybees for communicating and navigating distance flown and for evaluating its energetic costs. PMID:20018787
Tryjanowski, Piotr; Skórka, Piotr; Sparks, Tim H; Biaduń, Waldemar; Brauze, Tomasz; Hetmański, Tomasz; Martyka, Rafał; Indykiewicz, Piotr; Myczko, Łukasz; Kunysz, Przemysław; Kawa, Piotr; Czyż, Stanisław; Czechowski, Paweł; Polakowski, Michał; Zduniak, Piotr; Jerzak, Leszek; Janiszewski, Tomasz; Goławski, Artur; Duduś, Leszek; Nowakowski, Jacek J; Wuczyński, Andrzej; Wysocki, Dariusz
2015-10-01
Bird feeding is one of the most widespread direct interactions between man and nature, and this has important social and environmental consequences. However, this activity can differ between rural and urban habitats, due to inter alia habitat structure, human behaviour and the composition of wintering bird communities. We counted birds in 156 squares (0.25 km(2) each) in December 2012 and again in January 2013 in locations in and around 26 towns and cities across Poland (in each urban area, we surveyed 3 squares and also 3 squares in nearby rural areas). At each count, we noted the number of bird feeders, the number of bird feeders with food, the type of feeders, additional food supplies potentially available for birds (bread offered by people, bins) and finally the birds themselves. In winter, urban and rural areas differ in the availability of food offered intentionally and unintentionally to birds by humans. Both types of food availability are higher in urban areas. Our findings suggest that different types of bird feeder support only those species specialized for that particular food type and this relationship is similar in urban and rural areas.
Ushitani, Tomokazu; Perry, Clint J; Cheng, Ken; Barron, Andrew B
2016-02-01
Normally, worker honey bees (Apis mellifera) begin foraging when more than 2 weeks old as adults, but if individual bees or the colony is stressed, bees often begin foraging precociously. Here, we examined whether bees that accelerated their behavioural development to begin foraging precociously differed from normal-aged foragers in cognitive performance. We used a social manipulation to generate precocious foragers from small experimental colonies and tested their performance in a free-flight visual reversal learning task, and a test of spatial memory. To assess spatial memory, bees were trained to learn the location of a small sucrose feeder within an array of three landmarks. In tests, the feeder and one landmark were removed and the search behaviour of the bees was recorded. Performance of precocious and normal-aged foragers did not differ in a visual reversal learning task, but the two groups showed a clear difference in spatial memory. Flight behaviour suggested normal-aged foragers were better able to infer the position of the removed landmark and feeder relative to the remaining landmarks than precocious foragers. Previous studies have documented the cognitive decline of old foragers, but this is the first suggestion of a cognitive deficit in young foragers. These data imply that worker honey bees continue their cognitive development during the adult stage. These findings may also help to explain why precocious foragers perform quite poorly as foragers and have a higher than normal loss rate. © 2016. Published by The Company of Biologists Ltd.
High pressure rotary piston coal feeder for coal gasification applications
Gencsoy, Hasan T.
1977-05-24
The subject development is directed to an apparatus for feeding pulverized coal into a coal gasifier operating at relatively high pressures and elevated temperatures. This apparatus is a rotary piston feeder which comprises a circular casing having a coal loading opening therein diametrically opposed from a coal discharge and contains a rotatable discoid rotor having a cylinder in which a reciprocateable piston is disposed. The reciprocation of the piston within the cylinder is provided by a stationary conjugate cam arrangement whereby the pulverized coal from a coal hopper at atmospheric pressure can be introduced into the cylinder cavity and then discharged therefrom into the high-pressure gasifier without the loss of high pressure gases from within the latter.
View northwest, discharge basin, floor, showing cement cross beams built ...
View northwest, discharge basin, floor, showing cement cross beams built on stone bases - Glens Falls Feeder, Sluice, Along south side of Glens Falls Feeder between locks 10 & 20, Hudson Falls, Washington County, NY
Spacelab 4: Primate experiment support hardware
NASA Astrophysics Data System (ADS)
Fusco, P. R.; Peyran, R. J.
1984-05-01
A squirrel monkey feeder and automatic urine collection system were designed to fly on the Spacelab 4 Shuttle Mission presently scheduled for January 1986. Prototypes of the feeder and urine collection systems were fabricated and extensively tested on squirrel monkeys at the National Aeronautics and Space Administration's (NASA) Ames Research Center (ARC). The feeder design minimizes impact on the monkey's limited space in the cage and features improved reliability and biocompatibility over previous systems. The urine collection system is the first flight qualified, automatic urine collection device for squirrel monkeys. Flight systems are currently being fabricated.
Spacelab 4: Primate experiment support hardware
NASA Technical Reports Server (NTRS)
Fusco, P. R.; Peyran, R. J.
1984-01-01
A squirrel monkey feeder and automatic urine collection system were designed to fly on the Spacelab 4 Shuttle Mission presently scheduled for January 1986. Prototypes of the feeder and urine collection systems were fabricated and extensively tested on squirrel monkeys at the National Aeronautics and Space Administration's (NASA) Ames Research Center (ARC). The feeder design minimizes impact on the monkey's limited space in the cage and features improved reliability and biocompatibility over previous systems. The urine collection system is the first flight qualified, automatic urine collection device for squirrel monkeys. Flight systems are currently being fabricated.
Xue, Fei; Ma, Yinghong; Chen, Y Eugene; Zhang, Jifeng; Lin, Tzu-An; Chen, Chien-Hong; Lin, Wei-Wen; Roach, Marsha; Ju, Jyh-Cherng; Yang, Lan; Du, Fuliang; Xu, Jie
2012-08-01
The rabbit is a classical experimental animal species. A major limitation in using rabbits for biomedical research is the lack of germ-line-competent rabbit embryonic stem cells (rbESCs). We hypothesized that the use of homologous feeder cells and recombinant rabbit leukemia inhibitory factor (rbLIF) might improve the chance in deriving germ-line-competent rbES cells. In the present study, we established rabbit embryonic fibroblast (REF) feeder layers and synthesized recombinant rbLIF. We derived a total of seven putative rbESC lines, of which two lines (M5 and M23) were from culture Condition I using mouse embryonic fibroblasts (MEFs) as feeders supplemented with human LIF (hLIF) (MEF+hLIF). Another five lines (R4, R9, R15, R21, and R31) were derived from Condition II using REFs as feeder cells supplemented with rbLIF (REF+rbLIF). Similar derivation efficiency was observed between these two conditions (8.7% vs. 10.2%). In a separate experiment with 2×3 factorial design, we examined the effects of feeder cells (MEF vs. REF) and LIFs (mLIF, hLIF vs. rbLIF) on rbESC culture. Both Conditions I and II supported satisfactory rbESC culture, with similar or better population doubling time and colony-forming efficiency than other combinations of feeder cells with LIFs. Rabbit ESCs derived and maintained on both conditions displayed typical ESC characteristics, including ESC pluripotency marker expression (AP, Oct4, Sox2, Nanog, and SSEA4) and gene expression (Oct4, Sox2, Nanog, c-Myc, Klf4, and Dppa5), and the capacity to differentiate into three primary germ layers in vitro. The present work is the first attempt to establish rbESC lines using homologous feeder cells and recombinant rbLIF, by which the rbESCs were derived and maintained normally. These cell lines are unique resources and may facilitate the derivation of germ-line-competent rbESCs.
View southeast, interior of second drop, foundation and footwall and ...
View southeast, interior of second drop, foundation and footwall and sidewalls, showing failed lower arch - Glens Falls Feeder, Sluice, Along south side of Glens Falls Feeder between locks 10 & 20, Hudson Falls, Washington County, NY
Extremum Seeking Control of Smart Inverters for VAR Compensation
DOE Office of Scientific and Technical Information (OSTI.GOV)
Arnold, Daniel; Negrete-Pincetic, Matias; Stewart, Emma
2015-09-04
Reactive power compensation is used by utilities to ensure customer voltages are within pre-defined tolerances and reduce system resistive losses. While much attention has been paid to model-based control algorithms for reactive power support and Volt Var Optimization (VVO), these strategies typically require relatively large communications capabilities and accurate models. In this work, a non-model-based control strategy for smart inverters is considered for VAR compensation. An Extremum Seeking control algorithm is applied to modulate the reactive power output of inverters based on real power information from the feeder substation, without an explicit feeder model. Simulation results using utility demand informationmore » confirm the ability of the control algorithm to inject VARs to minimize feeder head real power consumption. In addition, we show that the algorithm is capable of improving feeder voltage profiles and reducing reactive power supplied by the distribution substation.« less
Mass extinctions: Ecological selectivity and primary production
NASA Astrophysics Data System (ADS)
Rhodes, Melissa Clark; Thayer, Charles W.
1991-09-01
If mass extinctions were caused by reduced primary productivity, then extinctions should be concentrated among animals with starvation-susceptible feeding modes, active lifestyles, and high-energy budgets. The stratigraphic ranges (by stage) of 424 genera of bivalves and 309 genera of articulate brachiopods suggest that there was an unusual reduction of primary productivity at the Cretaceous/Tertiary (K/T) boundary extinction. For bivalves at the K/T, there were (1) selective extinction of suspension feeders and other susceptible trophic categories relative to deposit feeders and other resistant categories, and (2) among suspension feed-ers, selective extinction of bivalves with active locomotion. During the Permian-Triassic (P/Tr) extinction and Jurassic background time, extinction rates among suspension feeders were greater for articulate brachiopods than for bivalves. But during the K/T event, extinction rates of articulates and suspension-feeding bivalves equalized, possibly because the low-energy budgets of articulates gave them an advantage when food was scarce.
Subjective value of risky foods for individual domestic chicks: a hierarchical Bayesian model.
Kawamori, Ai; Matsushima, Toshiya
2010-05-01
For animals to decide which prey to attack, the gain and delay of the food item must be integrated in a value function. However, the subjective value is not obtained by expected profitability when it is accompanied by risk. To estimate the subjective value, we examined choices in a cross-shaped maze with two colored feeders in domestic chicks. When tested by a reversal in food amount or delay, chicks changed choices similarly in both conditions (experiment 1). We therefore examined risk sensitivity for amount and delay (experiment 2) by supplying one feeder with food of fixed profitability and the alternative feeder with high- or low-profitability food at equal probability. Profitability varied in amount (groups 1 and 2 at high and low variance) or in delay (group 3). To find the equilibrium, the amount (groups 1 and 2) or delay (group 3) of the food in the fixed feeder was adjusted in a total of 18 blocks. The Markov chain Monte Carlo method was applied to a hierarchical Bayesian model to estimate the subjective value. Chicks undervalued the variable feeder in group 1 and were indifferent in group 2 but overvalued the variable feeder in group 3 at a population level. Re-examination without the titration procedure (experiment 3) suggested that the subjective value was not absolute for each option. When the delay was varied, the variable option was often given a paradoxically high value depending on fixed alternative. Therefore, the basic assumption of the uniquely determined value function might be questioned.
NASA Astrophysics Data System (ADS)
de Lima, Evandro Fernandes; Waichel, Breno Leitão; Rossetti, Lucas De Magalhães May; Sommer, Carlos Augusto; Simões, Matheus Silva
2018-01-01
In the Rio Grande do Sul State, southern Brazil, the volcanic sequence of the Paraná-Etendeka Igneous Province consists of pahoehoe and rubbly pahoehoe lava flows with basaltic and basaltic andesitic composition respectively, overlaid by acidic volcanic rocks. The acidic volcanic rocks of the Paraná-Etendeka Igneous Province exhibit textures and structures that can be related to effusive and/or explosive eruptions generating predominantly rheoignimbrites. The huge lava volume related to the emplacement of large igneous provinces implicates on efficient feeder systems that are more commonly observed in continental environments. In the Paraná-Etendeka Igneous Province, feeders of basaltic rocks are exposed in several dyke swarms (Ponta Grossa NW trending, Florianópolis/Skeleton Coast (NW Namibia) N-S trending, Serra do Mar NE trending and Henties Bay/Outjo NE trending). In contrast, the only feeder system proposed to the acidic rocks of the Paraná-Etendeka Igneous Province is the Messum complex in Namibia (Milner et al. 1995). In the study area, the opening of three quarries for the extraction of dimension stones has exposed impressive structures/textures that show the effusive emplacement and the ductile to fragile-ductile magma transition along the acidic feeder dykes. Besides that, magma mixing/mingling processes between two acidic magmas are observed along the dykes. Here we describe new occurrences of acidic feeder dykes, correlate the dykes with acidic flows and discuss their importance to understand the emplacement of the Palmas type acid units in southern Brazil.
2. Photocopy of a drawing (original in the Collection of ...
2. Photocopy of a drawing (original in the Collection of the PL&C, Shelf 117, Drawing 155) SECTION OF THE MOODY STREET FEEDER, DECEMBER 30, 1847 - Moody Street Feeder, Moody Street vicinity, Lowell, Middlesex County, MA
30 CFR 77.1801 - Overcurrent protection.
Code of Federal Regulations, 2010 CFR
2010-07-01
... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Overcurrent protection. 77.1801 Section 77.1801... Wires and Trolley Feeder Wires § 77.1801 Overcurrent protection. Trolley wires and trolley feeder wires shall be provided with overcurrent protection. ...
The deep structure of a sea-floor hydrothermal deposit
Zierenberg, R.A.; Fouquet, Y.; Miller, D.J.; Bahr, J.M.; Baker, P.A.; Bjerkgard, T.; Brunner, C.A.; Duckworth, R.C.; Gable, R.; Gieskes, J.; Goodfellow, W.D.; Groschel-Becker, H. M.; Guerin, G.; Ishibashi, J.; Iturrino, G.; James, R.H.; Lackschewitz, K.S.; Marquez, L.L.; Nehlig, P.; Peter, J.M.; Rigsby, C.A.; Schultheiss, P.; Shanks, Wayne C.; Simoneit, B.R.T.; Summit, M.; Teagle, D.A.H.; Urbat, M.; Zuffa, G.G.
1998-01-01
Hydrothermal circulation at the crests of mid-ocean ridges plays an important role in transferring heat from the interior of the Earth. A consequence of this hydrothermal circulation is the formation of metallic ore bodies known as volcanic-associated massive sulphide deposits. Such deposits, preserved on land, were important sources of copper for ancient civilizations and continue to provide a significant source of base metals (for example, copper and zinc). Here we present results from Ocean Drilling Program Leg 169, which drilled through a massive sulphide deposit on the northern Juan de Fuca spreading centre and penetrated the hydrothermal feeder zone through which the metal-rich fluids reached the sea floor. We found that the style of feeder-zone mineralization changes with depth in response to changes in the pore pressure of the hydrothermal fluids and discovered a stratified zone of high-grade copper-rich replacement mineralization below the massive sulphide deposit. This copper-rich zone represents a type of mineralization not previously observed below sea-floor deposits, and may provide new targets for land-based mineral exploration.
Lenihan, Catherine; Rogers, Caroline; Metcalfe, Anthony D; Martin, Yella H
2014-12-01
The use of cultured epithelial keratinocytes in the treatment of burns and skin graft donor sites is well established in clinical practice. The most widely used culture method for clinical use was originally developed by Rheinwald and Green 40 years ago. This system uses irradiated mouse dermal fibroblasts as a feeder cell layer to promote keratinocyte growth, a process that is costly and labor-intensive for health care providers. The medium formulation contains several components of animal origin, which pose further safety risks for patients. Improvements and simplification in the culturing process would lead to clear advantages: improved safety through reduction of xenobiotic components and reduction in cost for health care providers by dispensing with feeder cells. We compared the Rheinwald and Green method to culture in three commercially available, feeder-free media systems with defined/absent components of animal origin. During the isolation process, short incubation times in high-strength trypsin resulted in increased numbers of liberated keratinocyte stem cells compared with longer incubation times. All three commercially available media tested in this study could support the expansion of keratinocytes, with phenotypes comparable to cells expanded using the established Rheinwald and Green method. Growth rates varied, with two of the media displaying comparable growth rates, whereas the third was significantly slower. Our study demonstrates the suitability of such feeder-free media systems in clinical use. It further outlines a range of techniques to evaluate keratinocyte phenotype when assessing the suitability of cells for clinical application. Copyright © 2014 International Society for Cellular Therapy. Published by Elsevier Inc. All rights reserved.
47 CFR 25.147 - Licensing provision for NGSO MSS feeder downlinks in the band 6700-6875 MHz.
Code of Federal Regulations, 2014 CFR
2014-10-01
... COMMISSION (CONTINUED) COMMON CARRIER SERVICES SATELLITE COMMUNICATIONS Applications and Licenses Space Stations § 25.147 Licensing provision for NGSO MSS feeder downlinks in the band 6700-6875 MHz. If an NGSO...
47 CFR 25.147 - Licensing provision for NGSO MSS feeder downlinks in the band 6700-6875 MHz.
Code of Federal Regulations, 2012 CFR
2012-10-01
... COMMISSION (CONTINUED) COMMON CARRIER SERVICES SATELLITE COMMUNICATIONS Applications and Licenses Space Stations § 25.147 Licensing provision for NGSO MSS feeder downlinks in the band 6700-6875 MHz. If an NGSO...
47 CFR 25.147 - Licensing provision for NGSO MSS feeder downlinks in the band 6700-6875 MHz.
Code of Federal Regulations, 2010 CFR
2010-10-01
... COMMISSION (CONTINUED) COMMON CARRIER SERVICES SATELLITE COMMUNICATIONS Applications and Licenses Space Stations § 25.147 Licensing provision for NGSO MSS feeder downlinks in the band 6700-6875 MHz. If an NGSO...
47 CFR 25.147 - Licensing provision for NGSO MSS feeder downlinks in the band 6700-6875 MHz.
Code of Federal Regulations, 2011 CFR
2011-10-01
... COMMISSION (CONTINUED) COMMON CARRIER SERVICES SATELLITE COMMUNICATIONS Applications and Licenses Space Stations § 25.147 Licensing provision for NGSO MSS feeder downlinks in the band 6700-6875 MHz. If an NGSO...
47 CFR 25.147 - Licensing provision for NGSO MSS feeder downlinks in the band 6700-6875 MHz.
Code of Federal Regulations, 2013 CFR
2013-10-01
... COMMISSION (CONTINUED) COMMON CARRIER SERVICES SATELLITE COMMUNICATIONS Applications and Licenses Space Stations § 25.147 Licensing provision for NGSO MSS feeder downlinks in the band 6700-6875 MHz. If an NGSO...
Evaluation of Advanced Microwave Landing System Procedures in the New York Terminal Area
1991-03-01
sector controller called the CAMRN sector who must then sequence that traffic with multiple feeders from the south before handing off to the final...Right (13R) were all being used by landing traffic, the final controller handled the runway 22 arrivals and the CAMRN controller handled the runway 13R...Feeder Fix AAL678 DC10 H 00:09:00 AAL68 B767 H 00:23:00 AAL588 A300 H 00:27:00 PAA224 A300 H 01:20:00 4/ TWAll L101 H 01:34:00 CAMRN Feeder Fix DAL144
Vertical-Screw-Auger Conveyer Feeder
NASA Technical Reports Server (NTRS)
Walton, Otis (Inventor); Vollmer, Hubert J. (Inventor)
2016-01-01
A conical feeder is attached to a vertically conveying screw auger. The feeder is equipped with scoops and rotated from the surface to force-feed regolith the auger. Additional scoops are possible by adding a cylindrical section above the conical funnel section. Such then allows the unit to collect material from swaths larger in diameter than the enclosing casing pipe of the screw auger. A third element includes a flexible screw auger. All three can be used in combination in microgravity and zero atmosphere environments to drill and recover a wide area of subsurface regolith and entrained volatiles through a single access point on the surface.
Microstrip Patch Antenna And Method
NASA Technical Reports Server (NTRS)
Fink, Patrick W. (Inventor)
2001-01-01
Method and apparatus are provided for a microstrip feeder structure for supplying properly phased signals to each radiator element in a microstrip antenna array that may be utilized for radiating circularly polarized electromagnetic waves. In one disclosed embodiment. the microstrip feeder structure includes a plurality of microstrip sections many or all of which preferably have an electrical length substantially equal to one-quarter wavelength at the antenna operating frequency. The feeder structure provides a low loss feed structure that may be duplicated multiple times through a set of rotations and translations to provide a radiating array of the desired size.
Movement of feeder-using songbirds: the influence of urban features.
Cox, Daniel T C; Inger, Richard; Hancock, Steven; Anderson, Karen; Gaston, Kevin J
2016-11-23
Private gardens provide vital opportunities for people to interact with nature. The most popular form of interaction is through garden bird feeding. Understanding how landscape features and seasons determine patterns of movement of feeder-using songbirds is key to maximising the well-being benefits they provide. To determine these patterns we established three networks of automated data loggers along a gradient of greenspace fragmentation. Over a 12-month period we tracked 452 tagged blue tits Cyantistes caeruleus and great tits Parus major moving between feeder pairs 9,848 times, to address two questions: (i) Do urban features within different forms, and season, influence structural (presence-absence of connections between feeders by birds) and functional (frequency of these connections) connectivity? (ii) Are there general patterns of structural and functional connectivity across forms? Vegetation cover increased connectivity in all three networks, whereas the presence of road gaps negatively affected functional but not structural connectivity. Across networks structural connectivity was lowest in the summer when birds maintain breeding territories, however patterns of functional connectivity appeared to vary with habitat fragmentation. Using empirical data this study shows how key urban features and season influence movement of feeder-using songbirds, and we provide evidence that this is related to greenspace fragmentation.
NASA Astrophysics Data System (ADS)
Nur'afalia, D.; Afifa, F.; Rubianto, L.; Handayeni, K. D. M. E.
2018-01-01
The aim of this research is to determine the optimal feeder network route that integrates with BRT (Bus Rapid Transit). Palembang, a high growing population city with unresolved transportation demand sector. BRT as main public transportation could not fulfill people’s demand in transportation, especially in Alang-Alang Lebar sub-district. As an impact, the usage of private vehicles increases along the movement toward the city center. The concept of Network Integration that integrates feeder network with BRT is expected to be a solution to suppress the rate of private vehicles’ usage and to improve public transportation service, so that the use of BRT will be increased in the suburban area of Palembang. The method used to identifying the optimal route using Route Analysis method is route analysis using Tranetsim 0.4. The best route is obtained based on 156 movement samples. The result is 58,7% from 199 mobility’s potency of private vehicle usage’s can be reduced if there is a feeder network’s route in Alang-Alang Lebar’s sub-district. From the result, the existance of integration between feeder network and BRT is potential enough to reduce the usage of private vehicles and supports the sustainability of transportation mobility in Palembang City.
Wilson, Tanya R; LeBlanc, Stephen J; DeVries, Trevor J; Haley, Derek B
2018-06-01
Automatic milk feeders (AMF) for young dairy calves are widely used in the dairy industry. These feeders are thought to have benefits for calf health and welfare and may reduce labor required for feeding; however, little is known about how calves adapt to feeding with AMF. The objective of this study was to observe the effects of feeding stall design on calves learning to use the AMF. The hypothesis was that solid side stalls, compared with steel bar stalls, would result in a longer latency to approach and feed from the AMF without assistance. A total of 147 Holstein calves (80 male and 67 female) were enrolled at 4 d of age, introduced to a group pen, and, at the same time, trained on an AMF. For training, calves were allowed to suck on the trainer's fingers and guided to the teat. Calves were allocated to 1 of 2 stall designs at the pen level, depending on which treatment cohort they were born into, either with steel bar stall walls (n = 46 male, 34 female calves) or with solid side stall walls (n = 34 male, 33 female calves). For 72 h after introductory training on the AMF, data from the feeders were collected and calf behavior was monitored by video. Outcomes measured included latency to first voluntary visit to the feeder and to first feeding, time spent in the feeder, amount of milk consumed over 72 h, number of retraining sessions required (retrained if <2 L was consumed every 12 h), and exploratory behavior, such as sniffing and licking of the feeder. Data were analyzed using mixed effects linear regression models or a Poisson model for the outcome of retraining. For certain outcomes the effects of stall design interacted with difficulty of training (willingness to enter feeder and drink); for the 38% of calves that were scored as moderately difficult to train on a scale of easy, moderate, or difficult, treatment (stall design) differences were detected. These calves took 2× longer to lick or bite toward the nipple, 2× longer to first voluntarily feeding, and consumed less milk over 72 h following training when trained on the steel bar stall design. These results suggest simple features of a stall may influence how quickly calves learn to use an AMF, but that the influence of stall wall design was affected by how easy calves were to train on the feeder upon initial introduction, which may depend in part on certain aspects of calf temperament. For many calves, solid side stalls at an AMF resulted faster in adaption than the steel bar stalls. Copyright © 2018 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.
Chichagova, Valeria; Sanchez-Vera, Irene; Armstrong, Lyle; Steel, David; Lako, Majlinda
2016-01-01
Human induced pluripotent stem cells (hiPSCs) provide a platform for studying human disease in vitro, increase our understanding of human embryonic development, and provide clinically relevant cell types for transplantation, drug testing, and toxicology studies. Since their discovery, numerous advances have been made in order to eliminate issues such as vector integration into the host genome, low reprogramming efficiency, incomplete reprogramming and acquisition of genomic instabilities. One of the ways to achieve integration-free reprogramming is by using RNA-based Sendai virus. Here we describe a method to generate hiPSCs with Sendai virus in both feeder-free and feeder-dependent culture systems. Additionally, we illustrate methods by which to validate pluripotency of the resulting stem cell population.
View east, stone sluice, beginning of lower standing section, showing ...
View east, stone sluice, beginning of lower standing section, showing third drop, stone pier in center, cement piers to right - Glens Falls Feeder, Sluice, Along south side of Glens Falls Feeder between locks 10 & 20, Hudson Falls, Washington County, NY
DOE Office of Scientific and Technical Information (OSTI.GOV)
Lee, In Joon; Chung, Jin Wook, E-mail: chungjw@snu.ac.kr; Yin, Yong Hu
2015-10-15
PurposeThis study was designed to analyze retrospectively the performance of cone-beam computed tomography (CBCT) hepatic arteriography in depicting tumors and their feeders and to investigate the related determining factors in chemoembolization for hepatocellular carcinoma (HCC).MethodsEighty-six patients with 142 tumors satisfying the imaging diagnosis criteria of HCC were included in this study. The performance of CBCT hepatic arteriography for chemoembolization per tumor and per patient was evaluated using maximum intensity projection images alone (MIP analysis) or MIP combined with multiplanar reformation images (MIP + MPR analysis) regarding the following three aspects: tumor depiction, confidence of tumor feeder detection, and trackability of tumor feeders.more » Tumor size, tumor enhancement, tumor location, number of feeders, diaphragmatic motion, portal vein enhancement, and hepatic artery to parenchyma enhancement ratio were regarded as potential determining factors.ResultsTumors were depicted in 125 (88.0 %) and 142 tumors (100 %) on MIP and MIP + MPR analysis, respectively. Imaging performances on MIP and MIP + MPR analysis were good enough to perform subsegmental chemoembolization without additional angiographic investigation in 88 (62.0 %) and 128 tumors (90.1 %) on per-tumor basis and in 43 (50 %) and 73 (84.9 %) on per-patient basis, respectively. Significant determining factors for performance in MIP + MPR analysis on per tumor basis were tumor size (p = 0.030), tumor enhancement (0.005), tumor location (p = 0.001), and diaphragmatic motion (p < 0.001).ConclusionsCBCT hepatic arteriography provided sufficient information for subsegmental chemoembolization by depicting tumors and their feeders in the vast majority of patients. Combined analysis of MIP and MPR images was essential to enhance the performance of CBCT hepatic arteriography.« less
Jiang, Guangming; Wan, Xiaoju; Wang, Ming; Zhou, Jianhua; Pan, Jian; Wang, Baolong
2016-08-01
Mouse embryonic fibroblasts (MEFs) are widely used to prepare feeder layers for culturing embryonic stem cells (ESCs) or induced pluripotent stem cells (iPSCs) in vitro. Transportation lesions and exorbitant prices make the commercially obtained MEFs unsuitable for long term research. The aim of present study is to establish a method, which enables researchers to gain MEFs from mice and establish feeder layers by themselves in ordinary laboratories. MEFs were isolated from ICR mouse embryos at 12.5-17.5 day post-coitum (DPC) and cultured in vitro. At P2-P7, the cells were inactivated with mitomycin C or by X-ray irradiation. Then they were used to prepare feeder layers. The key factors of the whole protocol were analyzed to determine the optimal conditions for the method. The results revealed MEFs isolated at 12.5-13.5 DPC, and cultured to P3 were the best choice for feeder preparation, those P2 and P4-P5 MEFs were also suitable for the purpose. The P3-P5 MEFs treated with 10 μg/ml of mitomycin C for 3 h, or irradiated with X-ray at 1.5 Gy/min for 25 Gy were the most suitable feeder cells. Treating MEFs with 10 μg/ml of mitomycin C for 2.5 h, 15 μg/ml for 2.0 h, or irradiating the cells with 20 Gy of X-ray at 2.0 Gy/min could all serve as alternative methods for P3-P4 cells. Our study provides a reliable and economical way to obtain large amount of qualified MEFs for long term research of ESCs or iPSCs.
Feeding group responses of a Neotropical termite assemblage to rain forest fragmentation.
Davies, Richard G
2002-10-01
Biomass collapse and its associated microclimatic stresses within recently isolated rain forest fragments may negatively affect species diversity of most resident taxa. However, for some decomposer organisms, increased resource availability via accompanying tree die-off may effect positive responses, at least for a time, with implications for rates of nutrient cycling and greenhouse gas release. This study investigates the early effects of forest fragmentation on a Neotropical termite assemblage. Numbers of encounters (surrogate for relative abundance) and species richness of wood and leaf-litter feeders, soil feeders, and the whole assemblage, were studied across true forest islands and mainland sites at a hydroelectric reservoir in French Guiana. Results showed no overall effect of fragmentation on either total termite encounters or species richness. However, numbers of encounters and species richness of wood and leaf-litter feeders showed positive responses to forest fragmentation. By contrast, soil feeders showed a negative response for numbers of encounters and no significant effect for species richness. Environmental data suggest that increased tree die-off, and other edge effects associated with biomass collapse, were underway at the time of sampling. Resulting increase in resource availability may therefore explain the positive influence on wood and leaf-litter feeders. A possible decrease in predation pressure from ants with decrease in island size was not tested for, but was a likely effect of the flooded matrix habitat. Fragmentation effects on soil feeder encounters may be due to the energetic and microclimatic constraints of feeding lower down the humification gradient of termite food substrates, but were not sufficient to affect species richness. The patterns revealed suggest that rates of wood decomposition following tree die-off, and of soil nutrient cycling, under different rain forest fragmentation scenarios, merit further study.
[Spatial imprinting influence on development of cognitive process in adult animals].
Serkova, V V; Nikol'skaia, K A
2013-12-01
The influence of spatial imprinting on cognitive activity of adult mice F1 from DBA/2J C57BL/6J in a transformable multialternative maze has been studied. A control mice initially learned in a maze with "direct" and "bypass" pathway between feeders. They successfully formed a food-getting habit after 9-10 sessions using mainly direct pathway, so the final route decision was consistent with the principle of least action. Experimental mice previously placed into reduced maze with only "bypass" pathway between feeders for 1-2 trials (1-3 min), and turn up in the complete maze immediately after that. Experimental mice could not organize a food-getting behavior according a task conditions since attempted to include in final decision both "direct" and "bypass" pathways, united in a single ring-like construction. They demonstrated situational behavior running from one feeder to another one, despite of fact that therein had no feed. So it opposed the realization of least action principle, becoming a source of psycho-emotional stress. The results showed that spatial information perceiving in the first few minutes of exploring the experimental environment can manifest itself as the acquired preference and come in conflict with an instinctive one. Cognitive dissonance predetermined the direction of the cognitive process.
Veteikytė, Aušra; Šiekštelė, Rimantas; Tvaska, Bronius; Matijošytė, Inga
2017-05-01
Currently, much attention is paid to technologies which can be drivers of the circular economy across different sectors, in particular, to develop technologies for utilization or reusability of biocompatible materials from industrial waste. One of such is the milk whey, which is a cheap biobased raw material, the disposal of which is a major problem for the dairy industry. Our proposed and investigated technology is based on a continuous exploitation of the whey combining microbiology and biotechnology. Primarily, whey was used as a nutrition source for the cultivation of Kluyveromyces lactis with the aim to produce the targeted biocatalyst-lipase. During cultivation, the whey was transformed into the hydrolyzed form, which was further successfully applied as a protein feeder (external linker) for immobilization of lipase by cross-linked enzyme aggregate (CLEA) method. The first time use of whey as a co-feeder for immobilization of enzymes by CLEA method has shown promising results and increased the stability of lipases for temperature and organic solvents. Hydrolysis of rapeseed oil catalyzed with immobilized derivatives was obtained with 45-96% efficiency at non-optimized conditions. Additionally, the determined kinetic parameters indicated that the rate of p-nitrophenyl palmitate hydrolysis was not changed drastically after immobilization.
DOE Office of Scientific and Technical Information (OSTI.GOV)
Ruth, M.; Pratt, A.; Lunacek, M.
The combination of distributed energy resources (DER) and retail tariff structures to provide benefits to both utility consumers and the utilities is not well understood. To improve understanding, an Integrated Energy System Model (IESM) is being developed to simulate the physical and economic aspects of DER technologies, the buildings where they reside, and feeders servicing them. The IESM was used to simulate 20 houses with home energy management systems on a single feeder under a time-of-use (TOU) tariff to estimate economic and physical impacts on both the households and the distribution utilities. Home energy management systems (HEMS) reduce consumers’ electricmore » bills by precooling houses in the hours before peak electricity pricing. Utilization of HEMS reduce peak loads during high price hours but shifts it to hours with off-peak and shoulder prices, resulting in a higher peak load. used to simulate 20 houses with home energy management systems on a single feeder under a time-of-use (TOU) tariff to estimate economic and physical impacts on both the households and the distribution utilities. Home energy management systems (HEMS) reduce consumers’ electric bills by precooling houses in the hours before peak electricity pricing. Utilization of HEMS reduce peak loads during high price hours but shifts it to hours with off-peak and shoulder prices, resulting in a higher peak load.« less
Container barge feeder service study : Bridgeport, New Haven, New London, Norwich
DOT National Transportation Integrated Search
2001-03-01
The Connecticut Department of Transportation (ConnDOT) has conducted this study to determine the need and opportunity for establishing a Container Barge Feeder Service along Long Island Sound between the Port of New York and New Jersey (NY&NJ) and th...
Feeder-free reprogramming of human fibroblasts with messenger RNA.
Warren, Luigi; Wang, Jiwu
2013-11-13
This unit describes a feeder-free protocol for deriving induced pluripotent stem cells (iPSCs) from human fibroblasts by transfection of synthetic mRNA. The reprogramming of somatic cells requires transient expression of a set of transcription factors that collectively activate an endogenous gene regulatory network specifying the pluripotent phenotype. The necessary ectopic factor expression was first effected using retroviruses; however, as viral integration into the genome is problematic for cell therapy applications, the use of footprint-free vectors such as mRNA is increasingly preferred. Strong points of the mRNA approach include high efficiency, rapid kinetics, and obviation of a clean-up phase to purge the vector. Still, the method is relatively laborious and has, up to now, involved the use of feeder cells, which brings drawbacks including poor applicability to clinically oriented iPSC derivation. Using the methods described here, mRNA reprogramming can be performed without feeders at much-reduced labor and material costs relative to established protocols. Copyright © 2013 John Wiley & Sons, Inc.
Xue, Fei; Ma, Yinghong; Chen, Y. Eugene; Zhang, Jifeng; Lin, Tzu-An; Chen, Chien-Hong; Lin, Wei-Wen; Roach, Marsha; Ju, Jyh-Cherng; Yang, Lan; Du, Fuliang
2012-01-01
Abstract The rabbit is a classical experimental animal species. A major limitation in using rabbits for biomedical research is the lack of germ-line-competent rabbit embryonic stem cells (rbESCs). We hypothesized that the use of homologous feeder cells and recombinant rabbit leukemia inhibitory factor (rbLIF) might improve the chance in deriving germ-line-competent rbES cells. In the present study, we established rabbit embryonic fibroblast (REF) feeder layers and synthesized recombinant rbLIF. We derived a total of seven putative rbESC lines, of which two lines (M5 and M23) were from culture Condition I using mouse embryonic fibroblasts (MEFs) as feeders supplemented with human LIF (hLIF) (MEF+hLIF). Another five lines (R4, R9, R15, R21, and R31) were derived from Condition II using REFs as feeder cells supplemented with rbLIF (REF+rbLIF). Similar derivation efficiency was observed between these two conditions (8.7% vs. 10.2%). In a separate experiment with 2×3 factorial design, we examined the effects of feeder cells (MEF vs. REF) and LIFs (mLIF, hLIF vs. rbLIF) on rbESC culture. Both Conditions I and II supported satisfactory rbESC culture, with similar or better population doubling time and colony-forming efficiency than other combinations of feeder cells with LIFs. Rabbit ESCs derived and maintained on both conditions displayed typical ESC characteristics, including ESC pluripotency marker expression (AP, Oct4, Sox2, Nanog, and SSEA4) and gene expression (Oct4, Sox2, Nanog, c-Myc, Klf4, and Dppa5), and the capacity to differentiate into three primary germ layers in vitro. The present work is the first attempt to establish rbESC lines using homologous feeder cells and recombinant rbLIF, by which the rbESCs were derived and maintained normally. These cell lines are unique resources and may facilitate the derivation of germ-line-competent rbESCs. PMID:22775411
Veal marketing could return more than traditional weaning
USDA-ARS?s Scientific Manuscript database
How profitable is a system of marketing early-weaned calves for veal production versus a traditional system based on more traditional weaning and marketing feeder calves? In an attempt to answer this question, decision support software (Decision Evaluator for the Cattle Industry, DECI) developed at...
Analysis of the 60-Hz power system at KSC: The Orsino substation
NASA Technical Reports Server (NTRS)
Kalu, Alex O.
1989-01-01
An analysis of the Orsino Substation, a component (50 percent) of the 60-Hertz electric power system at the Kennedy Space Center, is presented. Presented here are separate single-line diagrams of the sixteen feeder circuits to permit easy access to information on the individual feeders for future planning. The load condition of each feeder and load break switch are presented and a heuristic reliability analysis of the system is performed. Information is given about the system fashion useful for decision making purposes. The beauty of it is in the simplified manner by which information about the system can be obtained.
DOE Office of Scientific and Technical Information (OSTI.GOV)
Rylander, Matthew; Reno, Matthew J.; Quiroz, Jimmy E.
This paper describes methods that a distribution engineer could use to determine advanced inverter settings to improve distribution system performance. These settings are for fixed power factor, volt-var, and volt-watt functionality. Depending on the level of detail that is desired, different methods are proposed to determine single settings applicable for all advanced inverters on a feeder or unique settings for each individual inverter. Seven distinctly different utility distribution feeders are analyzed to simulate the potential benefit in terms of hosting capacity, system losses, and reactive power attained with each method to determine the advanced inverter settings.
DOT National Transportation Integrated Search
1981-01-01
This document specifies the functional requirements for the AGT-SOS Feeder Systems Model (FSM), the type of hardware required, and the modeling techniques employed by the FSM. The objective of the FSM is to map the zone-to-zone transit patronage dema...
View southeast, stone sluice, top of lower standing section, showing ...
View southeast, stone sluice, top of lower standing section, showing row of cement piers in center, retaining wall to left, barge canal sluice to right - Glens Falls Feeder, Sluice, Along south side of Glens Falls Feeder between locks 10 & 20, Hudson Falls, Washington County, NY
47. FEEDER CANAL AT WILL'S BASIN. BOATS IN THE FOREGROUND ...
47. FEEDER CANAL AT WILL'S BASIN. BOATS IN THE FOREGROUND SHOW THE CONTRAST BETWEEN A FULLY LOADED CANAL BOAT (LEFT) AND AN EMPTY ONE (RIGHT). D, L & W RAILROAD'S DOUBLE INTERSECTION PRATT TRUSS BRIDGE IS VISIBLE IN BACKGROUND. - Morris Canal, Phillipsburg, Warren County, NJ
34. INTERIOR VIEW, SAME AS ABOVE WITH THE FEEDER ROD ...
34. INTERIOR VIEW, SAME AS ABOVE WITH THE FEEDER ROD BEING OFFERED INTO THE MACHINE; UNLIKE THE OTHER NAIL CUTTING MACHINES, THE NAIL PLATE MUST BE HAND FLIPPED AND HAND FED WITH THIS MACHINE - LaBelle Iron Works, Thirtieth & Wood Streets, Wheeling, Ohio County, WV
Alves, W de F; Mota, A S; Lima, R A A de; Bellezoni, R; Vasconcellos, A
2011-01-01
The composition of termite assemblages was analyzed in three caatinga sites of the Estação Ecológica do Seridó, located in the municipality of Serra Negra do Norte, in the state of Rio Grande do Norte, Brazil. These sites have been subjected to selective logging, and cleared for pasture and farming. A standardized sampling protocol for termite assemblages (30h/person/site) was conducted between September 2007 and February 2009. At each site we measured environmental variables, such as soil pH and organic matter, necromass stock, vegetation height, stem diameter at ankle height (DAH) and the largest and the smallest crown width. Ten species of termites, belonging to eight genera and three families, were found at the three experimental sites. Four feeding groups were sampled: wood-feeders, soil-feeders, wood-soil interface feeders and leaf-feeders. The wood-feeders were dominant in number of species and number of encounters at all sites. In general, the sites were not significantly different in relation to the environmental variables measured. The same pattern was observed for termite assemblages, where no significant differences in species richness, relative abundance and taxonomic and functional composition were observed between the three sites. The agreement between composition of assemblages and environmental variables reinforces the potential of termites as biological indicators of habitat quality.
Xin, Qiuhong; Ogura, Yukiko; Matsushima, Toshiya
2017-07-01
To examine how resource competition contributes to patch-use behaviour, we examined domestic chicks foraging in an I-shaped maze equipped with two terminal feeders. In a variable interval schedule, one feeder supplied grains three times more frequently than the other, and the sides were reversed midway through the experiment. The maze was partitioned into two lanes by a transparent wall, so that chicks fictitiously competed without actual interference. Stay time at feeders was compared among three groups. The "single" group contained control chicks; the "pair" group comprised the pairs of chicks tested in the fictitious competition; "mirror" included single chicks accompanied by their respective mirror images. Both "pair" and "mirror" chicks showed facilitated running. In terms of the patch-use ratio, "pair" chicks showed precise matching at approximately 3:1 with significant mutual dependence, whereas "single" and "mirror" chicks showed a comparable under-matching. The facilitated running increased visits to feeders, but failed to predict the patch-use ratio of the subject. At the reversal, quick switching occurred similarly in all groups, but the "pair" chicks revealed a stronger memory-based matching. Perceived competition therefore contributes to precise matching and lasting memory of the better feeder, in a manner dissociated from socially facilitated food search. Copyright © 2017 Elsevier B.V. All rights reserved.
NASA Astrophysics Data System (ADS)
Kirby, Michael X.; Miller, Henry M.
2005-03-01
Biogenic reefs built by oysters and other suspension feeders are vital components of estuarine ecosystems. By consuming phytoplankton, suspension feeders act to suppress accumulation of organic matter in the water column. Nutrient loading increases the rate of primary production, thereby causing eutrophication. As suspension feeders consume more organic matter from increasing abundance of phytoplankton, their rate of growth should also increase if they are food limited. We show here that the eastern oyster, Crassostrea virginica (Gmelin), from St. Mary's and Patuxent rivers, Chesapeake Bay, grew faster during anthropogenic eutrophication relative to C. virginica before eutrophication. Growth of shell height, shell thickness and adductor muscle increased after eutrophication began in the late 18th century. After 1860, growth decreased, perhaps reflecting the negative effects of hypoxia, harmful algal blooms, disease and fishing on oyster growth. These results are consistent with the view that an increasing supply of phytoplankton resulting from eutrophication enhanced growth of C. virginica between 1760 and 1860, before oyster reefs were degraded by destructive fishing practices between 1870 and 1930. Alternative factors, such as changes in water temperature, salinity, and fishing are less likely to be responsible for this pattern. These results have implications for restoration of oyster reefs in order to mitigate the effects of eutrophication in estuaries, as well as the paleoecological relationship between suspension feeders and paleoproductivity.
NASA Technical Reports Server (NTRS)
Wilson, Jeffrey D.
2011-01-01
A new C-band (5091 to 5150 MHz) airport communications system designated as Aeronautical Mobile Airport Communications System (AeroMACS) is being planned under the Federal Aviation Administration s NextGen program. An interference analysis software program, Visualyse Professional (Transfinite Systems Ltd), is being utilized to provide guidelines on limitations for AeroMACS transmitters to avoid interference with other systems. A scenario consisting of a single omni-directional transmitting antenna at each of the major contiguous United States airports is modeled and the steps required to build the model are reported. The results are shown to agree very well with a previous study.
NASA Astrophysics Data System (ADS)
Bang, Eunjin
This two-year study explored changes in practices and the emerging identities of beginning secondary science teachers who participated in an online science specific mentoring program. Fourteen beginning secondary science teachers and six experienced secondary science teachers were selected for the study. As a mixed methods study, data were gathered quantitatively and qualitatively. A hierarchical linear modeling was used in order to depict the changes in inquiry-based science practices as a result of content-focused online mentoring program. Qualitative data were collected via monthly semi-structured interviews, pre, post, and follow-up yearly semi-structured interviews, and finally online written dialogues of beginning secondary science teachers and their e-mentors. A mixed method was used that utilized the results of quantitative data, Items for Inquiry-Based Practice (IBP) scores, helped for selecting cases for qualitative analysis. Results indicated that there were no significant differences in IBP scores among the fourteen beginning secondary science teachers; however, three groups were detected: increasing use, no change, and decreasing use in inquiry-based practices. Porsha, who made increasing use, showed four emerging identities throughout two years: watchful-imitator, seeker, collaborator, and junior-leader. Nora, who made no change, showed only two emerging identities: imitator and seeker. Netty, who made decreasing use, showed also two emerging identities: lonely-follower and feeder. Different identities detected in online dialogue, namely Porsha as a whistleblower, Nora as a watchful-imitator, and Netty as a watchful-feeder. The corresponding responses of three beginning secondary science teachers' e-mentors were defender, provider, listener, pusher and umpire. This study provides not only an in-depth picture of the contemporary science education community of practice but also suggest a roadmap to design an effective induction program.
NASA Astrophysics Data System (ADS)
Cook, William Gordon
Corrosion and material degradation issues are of concern to all industries. However, the nuclear power industry must conform to more stringent construction, fabrication and operational guidelines due to the perceived additional risk of operating with radioactive components. Thus corrosion and material integrity are of considerable concern for the operators of nuclear power plants and the bodies that govern their operations. In order to keep corrosion low and maintain adequate material integrity, knowledge of the processes that govern the material's breakdown and failure in a given environment are essential. The work presented here details the current understanding of the general corrosion of stainless steel and carbon steel in nuclear reactor primary heat transport systems (PHTS) and examines the mechanisms and possible mitigation techniques for flow-assisted corrosion (FAC) in CANDU outlet feeder pipes. Mechanistic models have been developed based on first principles and a 'solution-pores' mechanism of metal corrosion. The models predict corrosion rates and material transport in the PHTS of a pressurized water reactor (PWR) and the influence of electrochemistry on the corrosion and flow-assisted corrosion of carbon steel in the CANDU outlet feeders. In-situ probes, based on an electrical resistance technique, were developed to measure the real-time corrosion rate of reactor materials in high-temperature water. The probes were used to evaluate the effects of coolant pH and flow on FAC of carbon steel as well as demonstrate of the use of titanium dioxide as a coolant additive to mitigated FAC in CANDU outlet feeder pipes.
DOE Office of Scientific and Technical Information (OSTI.GOV)
Narang, David; Ayyanar, Raja; Gemin, Paul
APS’s renewable energy portfolio, driven in part by Arizona’s Renewable Energy Standard (RES) currently includes more than 1100 MW of installed capacity, equating to roughly 3000 GWh of annual production. Overall renewable production is expected to grow to 6000 GWh by 2025. It is expected that distributed photovoltaics, driven primarily by lower cost, will contribute to much of this growth and that by 2025, distributed installations will account for half of all renewable production (3000GHW). As solar penetration increases, additional analysis may be required for routine utility processes to ensure continued safe and reliable operation of the electric distribution network.more » Such processes include residential or commercial interconnection requests and load shifting during normal feeder operations. Circuits with existing high solar penetration will also have to be studied and results will need to be evaluated for adherence to utility practices or strategy. Increased distributed PV penetration may offer benefits such as load offsetting, but it also has the potential to adversely impact distribution system operation. These effects may be exacerbated by the rapid variability of PV production. Detailed effects of these phenomena in distributed PV applications continue to be studied. Comprehensive, high-resolution electrical models of the distribution system were developed to analyze the impacts of PV on distribution circuit protection systems (including coordination and anti-islanding), predict voltage regulation and phase balance issues, and develop volt/VAr control schemes. Modeling methods were refined by validating against field measurements. To augment the field measurements, methods were developed to synthesize high resolution load and PV generation data to facilitate quasi-static time series simulations. The models were then extended to explore boundary conditions for PV hosting capability of the feeder and to simulate common utility practices such as feeder reconfiguration. The modeling and analysis methodology was implemented using open source tools and a process was developed to aid utility engineers in future interconnection requests. Methods to increase PV hosting capacity were also explored during the course of the study. A 700kVA grid-supportive inverter was deployed on the feeder and each grid support mode was demonstrated. Energy storage was explored through simulation and models were developed to calculate the optimum size and placement needed to increase PV hosting capacity. A tool was developed to aid planners in assigning relative costs and benefits to various strategies for increasing PV hosting capacity beyond current levels. Following the completion of the project, APS intends to use the tools and methods to improve the framework of future PV integration on its system. The tools and methods are also expected to aid other utilities to accelerate distributed PV deployment.« less
View north, stone sluice, head of 40foot break, showing failed ...
View north, stone sluice, head of 40-foot break, showing failed arch in center, stone pier in center right, cement piers to upper left, retaining wall in background - Glens Falls Feeder, Sluice, Along south side of Glens Falls Feeder between locks 10 & 20, Hudson Falls, Washington County, NY
Hathaway, Thomas J.; Bell, Jr., Harold S.
1979-01-01
This invention provides a solids feeder for feeding dry coal to a pressurized gasifier at elevated temperatures substantially without losing gas from the gasifier by providing a lock having a double-acting piston that feeds the coals into the gasifier, traps the gas from escaping, and expels the trapped gas back into the gasifier.
Federal Register 2010, 2011, 2012, 2013, 2014
2011-01-20
... DEPARTMENT OF THE INTERIOR Bureau of Reclamation Bunker Hill Groundwater Basin, Riverside-Corona... Draft Environmental Impact Statement (SDEIR/DEIS) for the proposed Riverside-Corona Feeder (RCF) Project... Bernardino, California 92410 Corona Public Library, 650 South Main Street, Corona, California 92882 Riverside...
30 CFR 57.12086 - Location of trolley wire.
Code of Federal Regulations, 2011 CFR
2011-07-01
... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Location of trolley wire. 57.12086 Section 57... Underground Only § 57.12086 Location of trolley wire. Trolley and trolley feeder wire shall be installed... limitations would prevent the safe installation or use of such trolley and trolley feeder wire. ...
30 CFR 57.12086 - Location of trolley wire.
Code of Federal Regulations, 2010 CFR
2010-07-01
... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Location of trolley wire. 57.12086 Section 57... Underground Only § 57.12086 Location of trolley wire. Trolley and trolley feeder wire shall be installed... limitations would prevent the safe installation or use of such trolley and trolley feeder wire. ...
Optimal foraging by birds: feeder-based experiments for secondary and post-secondary students
USDA-ARS?s Scientific Manuscript database
Optimal foraging theory attempts to explain the foraging patterns observed in animals, including their choice of particular food items and foraging locations. Here, we describe three exercises designed to test hypotheses about food choice and foraging habitat preference using bird feeders. These e...
77 FR 13191 - Airworthiness Directives; Bombardier, Inc. Airplanes
Federal Register 2010, 2011, 2012, 2013, 2014
2012-03-06
... corrosion and inadequate silver-plating. This AD requires replacing ADG power feeder cables. We are issuing this AD to prevent galvanic corrosion on ADG power feeder cables, which could result in damage to the... damaged due to galvanic corrosion. It was subsequently determined that the silver- plating is inadequate...
Soares, Filipa A.C.; Chandra, Amit; Thomas, Robert J.; Pedersen, Roger A.; Vallier, Ludovic; Williams, David J.
2014-01-01
The transfer of a laboratory process into a manufacturing facility is one of the most critical steps required for the large scale production of cell-based therapy products. This study describes the first published protocol for scalable automated expansion of human induced pluripotent stem cell lines growing in aggregates in feeder-free and chemically defined medium. Cells were successfully transferred between different sites representative of research and manufacturing settings; and passaged manually and using the CompacT SelecT automation platform. Modified protocols were developed for the automated system and the management of cells aggregates (clumps) was identified as the critical step. Cellular morphology, pluripotency gene expression and differentiation into the three germ layers have been used compare the outcomes of manual and automated processes. PMID:24440272
Organogenesis from transformed tomato explants.
Frary, Anne; Van Eck, Joyce
2005-01-01
Tomato was one of the first crops for which a genetic transformation system was reported involving regeneration by organogenesis from Agrobacterium-transformed explants. Since the initial reports, various factors have been studied that affect the efficiency of tomato transformation and the technique has been useful for the isolation and identification of many genes involved in plant disease resistance, morphology and development. In this method, cotyledon explants from in vitro-grown seedlings are precultured overnight on a tobacco suspension feeder layer. The explants are then inoculated with Agrobacterium and returned to the feeder layer for a 2-d period of cocultivation. After cocultivation, the explants are transferred to an MS-based selective regeneration medium containing zeatin. Regenerated shoots are then rooted on a separate selective medium. This protocol has been used with several tomato cultivars and routinely yields transformation efficiencies of 10-15%.
78 FR 79338 - Airworthiness Directives; Bombardier, Inc. Airplanes
Federal Register 2010, 2011, 2012, 2013, 2014
2013-12-30
...We propose to adopt a new airworthiness directive (AD) for certain Bombardier, Inc. Model DHC-8-400 series airplanes. This proposed AD was prompted by reports of missing clamps that are required to provide positive separation between the alternating current (AC) feeder cables and the hydraulic line of the landing gear alternate extension. This proposed AD would require inspecting for missing clamps, and related investigative and corrective actions if necessary. We are proposing this AD to detect and correct chafing of the AC feeder cable. A chafed and arcing AC feeder cable could puncture the adjacent hydraulic line, which, in combination with the use of the alternate extension system, could result in an in-flight fire.
DOE Office of Scientific and Technical Information (OSTI.GOV)
Sumner, Dennis; Vosburg, Tom; Brunner, Steve
This project titled “Research, Development and Demonstration of Peak Load Reduction on Distribution Feeders Using Distributed Energy Resources for the City of Fort Collins” evolved in response to the Department of Energy’s (DOE) Funding Opportunity Announcement (FOA) Number DE-PS26-07NT43119. Also referred to as the Fort Collins Renewable and Distributed System Integration (RDSI) Project, the effort was undertaken by a diverse group of local government, higher education and business organizations; and was driven by three overarching goals: I. Fulfill the requirements of the DOE FOA’s Area of Interest 2: Renewable and Distributed System Integration; most notably, to demonstrate the ability tomore » reduce electric system distribution feeder peak load by 15% or more through the coordinated use of Distributed Energy Resources (DER). II. Advance the expertise, technologies and infrastructure necessary to support the long term vision of the Fort Collins Zero Energy District (FortZED) and move towards creating a zero energy district in the Fort Collins “Old Town” area. III. Further the goals of the City of Fort Collins Energy Policy, including the development of a Smart Grid-enabled distribution system in Fort Collins, expanded use of renewable energy, increased energy conservation, and peak load reduction. Through the collaborative efforts of the partner organizations, the Fort Collins RDSI project was successful in achieving all three of these goals. This report is organized into two distinct sections corresponding to the two phases of the project: • Part 1: Feeder Peak Load Reduction and the FortZED Initiative. • Part 2: Forming and Operating Utility Microgrids and Managing Load and Production Variability The original project scope addressed the Part 1 feeder peak load reduction. That work took place from 2009 through 2011 and was largely complete when the project scope was amended to include a demonstration of microgrid operations. While leveraging the assets, partner relationships, and lessons learned from Part 1, Part 2 was managed and executed as a distinct and substantially independent sub-project during the spring and summer of 2013. Both Parts 1 and 2 of the overall RDSI project can be viewed as cohesive stand-alone bodies of work and are presented as such within this report. In addition to the narratives, this document includes two Appendices that were compiled to supplement information about the various aspects of activities performed during Parts 1 and 2 of the project. Moreover, these Appendices are organized (as outlined below) so as to directly relate to the narratives in Part 1 and 2 of this report. • Appendix - Part 1: describes the roles of each project participant in regards to the feeder peak load reduction effort, and • Appendix - Part 2: deals with the microgrid research/demonstration.« less
Breeding objectives for Targhee sheep.
Borg, R C; Notter, D R; Kuehn, L A; Kott, R W
2007-11-01
Breeding objectives were developed for Targhee sheep under rangeland production conditions. Traits considered were those for which EPD were available from the US National Sheep Improvement Program and included direct and maternal effects on 120-d weaning weight (WW and MM, respectively); yearling weight (YW); yearling fleece weight, fiber diameter, and staple length; and percent lamb crop (PLC), measured as the number of lambs born per 100 ewes lambing. A bioeconomic model was used to predict the effects of a change of 1 additive SD in EPD for each trait, holding all other traits constant at their mean, on animal performance, feed requirements, feed costs, and economic returns. Resulting economic weightings were then used to derive selection indexes. Indexes were derived separately for 3 prolificacy levels (1.41, 1.55, and 1.70 lambs/ewe lambing), 2 triplet survival levels (50 and 67%), 2 lamb pricing policies (with or without discounting of prices for heavy feeder lambs), and 3 forage cost scenarios (renting pasture, purchasing hay, or reducing flock size to accommodate increased nutrient requirements for production). Increasing PLC generally had the largest impact on profitability, although an increase in WW was equally important, with low feed costs and no discounting of prices for heavy feeder lambs. Increases in PLC were recommended at all 3 prolificacy levels, but with low triplet survival the value of increasing PLC eventually declined as the mean litter size increased to approximately 2.15 lambs/ewe lambing and above. Increasing YW (independent of WW) increased ewe maintenance costs and reduced profitability. Predicted changes in breeding values for WW and YW under index selection varied with lamb pricing policy and feed costs. With low feed costs or no discounts for heavy lambs, YW increased at a modest rate in association with increasing WW, but with high feed costs or discounting of heavy lambs, genetic trends in WW were reduced by approximately 50% to constrain increases in YW. Changes in EPD for MM or fleece traits generally had smaller effects on profitability than changes in PLC, WW, and YW. Two indexes designed to address current rangeland production conditions (low forage costs and discounting of heavy feeder lambs) or more intensive and integrated production with retained ownership and value-based marketing of lambs (higher forage costs and no discounting of heavy lambs) were anticipated to meet the needs of most Targhee producers.
Cultural eutrophication in coastal habitats has become a crucial problem for resource managers and policymakers and a critical area of research in ecological science. Models of eutrophication have been developed for some coastal habitats (e.g., Chesapeake Bay), but research on ma...
Cultural eutrophication in coastal habitats has become a crucial problem for resource managers and policymakers and a critical area of research in ecological science. Models of eutrophication have been developed for some coastal habitats (e.g., Chesapeake Bay), but research on ma...
Pollen as a tool for tracking stable flies.
USDA-ARS?s Scientific Manuscript database
The stable fly, (Stomoxys calcitrans L.), is an important pest of humans and livestock in many parts of the world. Its immature stages develop in decaying vegetation, e.g. hya, silage, feed, mulch and grass clippings, in agricultural and urban areas. although both sexes are oligate blood feeders, ...
46 CFR 58.25-55 - Overcurrent protection for steering-gear systems.
Code of Federal Regulations, 2010 CFR
2010-10-01
... overcurrent protection except short-circuit protection that is instantaneous and rated at 400% to 500% of— (1... for steering-gear systems. (a) Each feeder circuit for steering must be protected by a circuit breaker... motor for an alternating-current motor. (b) No feeder circuit for steering may have any overcurrent...
Code of Federal Regulations, 2013 CFR
2013-04-01
... held for breeding or dairy purposes, and $600 from the sale of a tractor. The income from the sale of... the sale of feeder cattle, which C bought for $500. The income from the sale of the feeder cattle is...
Code of Federal Regulations, 2011 CFR
2011-04-01
... held for breeding or dairy purposes, and $600 from the sale of a tractor. The income from the sale of... the sale of feeder cattle, which C bought for $500. The income from the sale of the feeder cattle is...
Code of Federal Regulations, 2014 CFR
2014-04-01
... held for breeding or dairy purposes, and $600 from the sale of a tractor. The income from the sale of... the sale of feeder cattle, which C bought for $500. The income from the sale of the feeder cattle is...
Code of Federal Regulations, 2012 CFR
2012-04-01
... held for breeding or dairy purposes, and $600 from the sale of a tractor. The income from the sale of... the sale of feeder cattle, which C bought for $500. The income from the sale of the feeder cattle is...
View southeast, stone sluice, top of upper standing section, showing ...
View southeast, stone sluice, top of upper standing section, showing cement piers over arch in foreground, foot of break at third drop in center, retaining wall to left, barge canal sluice to right - Glens Falls Feeder, Sluice, Along south side of Glens Falls Feeder between locks 10 & 20, Hudson Falls, Washington County, NY
77 FR 70355 - Airworthiness Directives; The Boeing Company Airplanes
Federal Register 2010, 2011, 2012, 2013, 2014
2012-11-26
... leakage zone) or heat damage to the APU power feeder cable, insulation blankets, or pressure bulkhead...) of the NPRM requires repair of the APU power feeder, insulation blankets, and clamps, if no primer... bulletin, which states, ``If visual indications of heat damage are found, do steps 6.c through 6.f...
30 CFR 77.1800 - Cutout switches.
Code of Federal Regulations, 2013 CFR
2013-07-01
... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Cutout switches. 77.1800 Section 77.1800... Wires and Trolley Feeder Wires § 77.1800 Cutout switches. Trolley wires and trolley feeder wires shall be provided with cutout switches at intervals of not more than 2,000 feet and near the beginning of...
30 CFR 77.1800 - Cutout switches.
Code of Federal Regulations, 2012 CFR
2012-07-01
... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Cutout switches. 77.1800 Section 77.1800... Wires and Trolley Feeder Wires § 77.1800 Cutout switches. Trolley wires and trolley feeder wires shall be provided with cutout switches at intervals of not more than 2,000 feet and near the beginning of...
30 CFR 77.1800 - Cutout switches.
Code of Federal Regulations, 2011 CFR
2011-07-01
... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Cutout switches. 77.1800 Section 77.1800... Wires and Trolley Feeder Wires § 77.1800 Cutout switches. Trolley wires and trolley feeder wires shall be provided with cutout switches at intervals of not more than 2,000 feet and near the beginning of...
30 CFR 77.1800 - Cutout switches.
Code of Federal Regulations, 2014 CFR
2014-07-01
... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Cutout switches. 77.1800 Section 77.1800... Wires and Trolley Feeder Wires § 77.1800 Cutout switches. Trolley wires and trolley feeder wires shall be provided with cutout switches at intervals of not more than 2,000 feet and near the beginning of...
46 CFR 58.25-65 - Feeder circuits.
Code of Federal Regulations, 2013 CFR
2013-10-01
... seconds of loss of power from the vessel's service switchboard; (2) Comes from an independent source of power in the steering-gear compartment; (3) Is used for no other purpose; and (4) Has a capacity for one... feeder circuit must have a current-carrying capacity of— (1) 125% of the rated full-load current rating...
46 CFR 58.25-65 - Feeder circuits.
Code of Federal Regulations, 2011 CFR
2011-10-01
... seconds of loss of power from the vessel's service switchboard; (2) Comes from an independent source of power in the steering-gear compartment; (3) Is used for no other purpose; and (4) Has a capacity for one... feeder circuit must have a current-carrying capacity of— (1) 125% of the rated full-load current rating...
46 CFR 58.25-65 - Feeder circuits.
Code of Federal Regulations, 2014 CFR
2014-10-01
... seconds of loss of power from the vessel's service switchboard; (2) Comes from an independent source of power in the steering-gear compartment; (3) Is used for no other purpose; and (4) Has a capacity for one... feeder circuit must have a current-carrying capacity of— (1) 125% of the rated full-load current rating...
46 CFR 58.25-65 - Feeder circuits.
Code of Federal Regulations, 2012 CFR
2012-10-01
... seconds of loss of power from the vessel's service switchboard; (2) Comes from an independent source of power in the steering-gear compartment; (3) Is used for no other purpose; and (4) Has a capacity for one... feeder circuit must have a current-carrying capacity of— (1) 125% of the rated full-load current rating...
46 CFR 58.25-65 - Feeder circuits.
Code of Federal Regulations, 2010 CFR
2010-10-01
... seconds of loss of power from the vessel's service switchboard; (2) Comes from an independent source of power in the steering-gear compartment; (3) Is used for no other purpose; and (4) Has a capacity for one... feeder circuit must have a current-carrying capacity of— (1) 125% of the rated full-load current rating...
Federal Register 2010, 2011, 2012, 2013, 2014
2013-06-12
... DEPARTMENT OF THE INTERIOR Bureau of Reclamation [A10-1999-6000-100-00-0-0-3, 3501000] Availability of Final Environmental Impact Statement; Bunker Hill Groundwater Basin, Riverside-Corona Feeder... proposed Riverside-Corona Feeder Project. DATES: The Bureau of Reclamation will not make a decision on the...
Counseling in the Elementary Feeder Schools.
ERIC Educational Resources Information Center
Dunham, Virginia
This brief paper presents the concept of transition counseling between a junior high school and its feeder school(s), designed to make the change from elementary into junior high less traumatic. Aside from routine sixth grade counseling, the counselors expanded their base of counseling to include all types of problems as well as all grade levels.…
40 CFR Table 4 to Subpart Kkkkk of... - Requirements for Performance Tests
Code of Federal Regulations, 2010 CFR
2010-07-01
... block average pressure drop values for the three test runs, and determine and record the 3-hour block... limit for the limestone feeder setting Data from the limestone feeder during the performance test You must ensure that you maintain an adequate amount of limestone in the limestone hopper, storage bin...
Energy Systems Integration News | Energy Systems Integration Facility |
distribution feeder models for use in hardware-in-the-loop (HIL) experiments. Using this method, a full feeder ; proposes an additional control loop to improve frequency support while ensuring stable operation. The and Frequency Deviation," also proposes an additional control loop, this time to smooth the wind
Lorenzo Marini; Robert A. Haack; Robert J. Rabaglia; Edoardo Petrucco Toffolo; Andrea Battisti; Massimo Faccoli
2011-01-01
Although invasion of exotic ambrosia beetles (fungus feeders) and bark beetles (phloem feeders) (Coleoptera: Curculionidae: Scolytinae) is considered a major threat to forest health worldwide, no studies have quantitatively investigated the anthropogenic and environmental factors shaping the biogeographical patterns of invasion by these insects across large spatial...
75 FR 78758 - Prohibited Transaction Exemptions From Certain Prohibited Transaction Restrictions
Federal Register 2010, 2011, 2012, 2013, 2014
2010-12-16
..., between the DB Torus Japan Master Portfolio (the Master Fund), in which the assets of a client employee...) Prior to investing in DB Torus Japan Fund Ltd. (hereinafter the Feeder Fund, the vehicle through which... DB Torus Japan Fund Ltd. (hereinafter the Feeder Fund, the vehicle through which investments in the...
Coal gasification system with a modulated on/off control system
Fasching, George E.
1984-01-01
A modulated control system is provided for improving regulation of the bed level in a fixed-bed coal gasifier into which coal is fed from a rotary coal feeder. A nuclear bed level gauge using a cobalt source and an ion chamber detector is used to detect the coal bed level in the gasifier. The detector signal is compared to a bed level set point signal in a primary controller which operates in proportional/integral modes to produce an error signal. The error signal is modulated by the injection of a triangular wave signal of a frequency of about 0.0004 Hz and an amplitude of about 80% of the primary deadband. The modulated error signal is fed to a triple-deadband secondary controller which jogs the coal feeder speed up or down by on/off control of a feeder speed change driver such that the gasifier bed level is driven toward the set point while preventing excessive cycling (oscillation) common in on/off mode automatic controllers of this type. Regulation of the bed level is achieved without excessive feeder speed control jogging.
Mathematical analysis of the honeybee waggle dance.
Okada, R; Ikeno, H; Kimura, T; Ohashi, Mizue; Aonuma, H; Ito, E
2012-01-01
A honeybee informs her nestmates of the location of a flower by doing a waggle dance. The waggle dance encodes both the direction of and distance to the flower from the hive. To reveal how the waggle dance benefits the colony, we created a Markov model of bee foraging behavior and performed simulation experiments by incorporating the biological parameters that we obtained from our own observations of real bees as well as from the literature. When two feeders were each placed 400 m away from the hive in different directions, a virtual colony in which honeybees danced and correctly transferred information (a normal, real bee colony) made significantly greater numbers of successful visits to the feeders compared to a colony with inaccurate information transfer. Howerer, when five feeders were each located 400 m from the hive, the inaccurate information transfer colony performed better than the normal colony. These results suggest that dancing's ability to communicate accurate information depends on the number of feeders. Furthermore, because non-dancing colonies always made significantly fewer visits than those two colonies, we concluded that dancing behavior is beneficial for hives' ability to visit food sources.
Preliminary analysis of hub and spoke air freight distribution system
NASA Technical Reports Server (NTRS)
Whitehead, A. H., Jr.
1978-01-01
A brief analysis is made of the hub and spoke air freight distribution system which would employ less than 15 hub centers world wide with very large advanced distributed-load freighters providing the line-haul delivery between hubs. This system is compared to a more conventional network using conventionally-designed long-haul freighters which travel between numerous major airports. The analysis calculates all of the transportation costs, including handling charges and pickup and delivery costs. The results show that the economics of the hub/spoke system are severely compromised by the extensive use of feeder aircraft to deliver cargo into and from the large freighter terminals. Not only are the higher costs for the smaller feeder airplanes disadvantageous, but their use implies an additional exchange of cargo between modes compared to truck delivery. The conventional system uses far fewer feeder airplanes, and in many cases, none at all. When feeder aircraft are eliminated from the hub/spoke system, however, that system is universally more economical than any conventional system employing smaller line-haul aircraft.
Microgrids for Service Restoration to Critical Load in a Resilient Distribution System
DOE Office of Scientific and Technical Information (OSTI.GOV)
Xu, Yin; Liu, Chen-Ching; Schneider, Kevin P.
icrogrids can act as emergency sources to serve critical loads when utility power is unavailable. This paper proposes a resiliency-based methodology that uses microgrids to restore critical loads on distribution feeders after a major disaster. Due to limited capacity of distributed generators (DGs) within microgrids, dynamic performance of the DGs during the restoration process becomes essential. In this paper, the stability of microgrids, limits on frequency deviation, and limits on transient voltage and current of DGs are incorporated as constraints of the critical load restoration problem. The limits on the amount of generation resources within microgrids are also considered. Bymore » introducing the concepts of restoration tree and load group, restoration of critical loads is transformed into a maximum coverage problem, which is a linear integer program (LIP). The restoration paths and actions are determined for critical loads by solving the LIP. A 4-feeder, 1069-bus unbalanced test system with four microgrids is utilized to demonstrate the effectiveness of the proposed method. The method is applied to the distribution system in Pullman, WA, resulting in a strategy that uses generators on the Washington State University campus to restore service to the Hospital and City Hall in Pullman.« less
Limat, A; Hunziker, T; Boillat, C; Bayreuther, K; Noser, F
1989-05-01
For growth at low seeding densities, keratinocytes isolated from human tissues like epidermis or hair follicles are dependent on mesenchyme-derived feeder cells such as the 3T3-cell employed so far. As an alternative method, the present study describes the use of post-mitotic human dermal fibroblasts sublethally irradiated or mitomycin C-treated. Special emphasis was put on efficient growth of primary keratinocyte cultures plated at very low seeding densities. Thus, outer root sheath cells isolated from two anagen human hair follicles and plated in a 35-mm culture dish (3 - 6 X 10(2) attached cells) grew to confluence within 3 weeks (6 - 8 X 10(5) cells). Similar results were obtained for interfollicular keratinocytes. A crucial point for the function of these fibroblast feeder cells is plating at appropriate densities, considering their tremendous increase in cell size at the post-mitotic state. Plating densities of 4 - 5 X 10(3/cm2 allow full spreading of the feeder cells and do not impede the settling and expansion of the keratinocytes. Major advantages of this system include easier handling and better reproducibility than using 3T3-cells. Moreover, homologous fibroblast feeders mimic more closely the physiologic situation and therefore might provide a valuable tool for studying interactions between human mesenchymal and epithelial cells. Finally, potential hazards of using transformed feeder cells from a different species in keratinocyte cultures raised for wound covering in humans could be thus avoided.
López-Paniagua, Marina; Nieto-Miguel, Teresa; de la Mata, Ana; Galindo, Sara; Herreras, José M; Corrales, Rosa M; Calonge, Margarita
2017-05-01
Transplantation of in vitro cultured limbal epithelial stem cells (LESCs) is a treatment widely used for LESC deficiency. However, the number of limbal tissue donors is limited, and protocols for LESC cultivation often include compounds and/or feeder layers that can induce side effects and/or increase the cost of the culture procedure. We investigated the feasibility of obtaining more than one limbal primary culture (LPC) from the same biopsy using a culture medium in which several potentially harmful compounds were replaced at the same time by biosafe supplements, allowing the LESC cultivation without feeder layers. We established feeder layer-free LPCs with three culture media: (1) a modified supplemental hormonal epithelial medium, containing potential harmful components (cholera toxin, dimethylsulfoxide, and fetal bovine serum [FBS]), (2) IOBA-FBS, a medium with FBS but with no other harmful supplements, and (3) IOBA-HS, similar to IOBA-FBS but with human serum instead of FBS. Additionally, the same limbal explant was consecutively cultured with IOBA-HS producing three cultures. LPCs were characterized by real-time reverse transcription polymerase chain reaction and/or immunofluorescence. LPCs cultured with the three media under feeder layer-free conditions showed cuboidal cells and no significant differences in the percentage of positive cells for limbal (ABCG2, p63, and K14) and corneal (K3, K12) proteins. Except for ABCG2, the relative mRNA expression of the LESC markers was significantly higher when IOBA-FBS or IOBA-HS was used. LPC1 showed characteristics similar to LPC0, while LPC2 cell morphology became elongated and the expression of some LESC markers was diminished. IOBA-HS enables the culturing of up to two biosafe homologous LPCs from one limbal tissue under feeder layer-free conditions. The routine use of this culture medium could improve both the biosafety and the number of available LPCs for potential clinical transplantation, as well as decrease the expense of the culture procedure.
Cox, Daniel T C; Gaston, Kevin J
2015-01-01
Interacting with nature is widely recognised as providing many health and well-being benefits. As people live increasingly urbanised lifestyles, the provision of food for garden birds may create a vital link for connecting people to nature and enabling them to access these benefits. However, it is not clear which factors determine the pleasure that people receive from watching birds at their feeders. These may be dependent on the species that are present, the abundance of individuals and the species richness of birds around the feeders. We quantitatively surveyed urban households from towns in southern England to determine the factors that influence the likeability of 14 common garden bird species, and to assess whether people prefer to see a greater abundance of individuals or increased species richness at their feeders. There was substantial variation in likeability across species, with songbirds being preferred over non-songbirds. Species likeability increased for people who fed birds regularly and who could name the species. We found a strong correlation between the number of species that a person could correctly identify and how connected to nature they felt when they watched garden birds. Species richness was preferred over a greater number of individuals of the same species. Although we do not show causation this study suggests that it is possible to increase the well-being benefits that people gain from watching birds at their feeders. This could be done first through a human to bird approach by encouraging regular interactions between people and their garden birds, such as through learning the species names and providing food. Second, it could be achieved through a bird to human approach by increasing garden songbird diversity because the pleasure that a person receives from watching an individual bird at a feeder is dependent not only on its species but also on the diversity of birds at the feeder.
Cox, Daniel T. C.; Gaston, Kevin J.
2015-01-01
Interacting with nature is widely recognised as providing many health and well-being benefits. As people live increasingly urbanised lifestyles, the provision of food for garden birds may create a vital link for connecting people to nature and enabling them to access these benefits. However, it is not clear which factors determine the pleasure that people receive from watching birds at their feeders. These may be dependent on the species that are present, the abundance of individuals and the species richness of birds around the feeders. We quantitatively surveyed urban households from towns in southern England to determine the factors that influence the likeability of 14 common garden bird species, and to assess whether people prefer to see a greater abundance of individuals or increased species richness at their feeders. There was substantial variation in likeability across species, with songbirds being preferred over non-songbirds. Species likeability increased for people who fed birds regularly and who could name the species. We found a strong correlation between the number of species that a person could correctly identify and how connected to nature they felt when they watched garden birds. Species richness was preferred over a greater number of individuals of the same species. Although we do not show causation this study suggests that it is possible to increase the well-being benefits that people gain from watching birds at their feeders. This could be done first through a human to bird approach by encouraging regular interactions between people and their garden birds, such as through learning the species names and providing food. Second, it could be achieved through a bird to human approach by increasing garden songbird diversity because the pleasure that a person receives from watching an individual bird at a feeder is dependent not only on its species but also on the diversity of birds at the feeder. PMID:26560968
Huang, Yi-Chau; Wang, Tzu-Wei; Sun, Jui-Sheng; Lin, Feng-Huei
2006-03-01
Fibroblasts produce a spectrum of necessary growth factors essential for growth and proliferation of a variety of cell types. In this study, the paracrine effect of mitomycin-C-treated fibroblasts with various densities in collagen gel for keratinocyte proliferation was investigated from which an optimum cell density and optimum conditioned medium would be determined to expand keratinocyte without further differentiation for skin equivalent tissue engineering. The optimum cell density in collagen feeder gel for optimum collected medium preparation will be determined by checking the level of keratinocyte growth factor and granulocyte macrophage colony-stimulating factor in conventional medium. The results showed that the cell density of 1 x 10(5) cells/gel in the feeder gel is better to produce optimum collected medium. The conditioned medium is prepared by mixing together the optimum collected medium and molecular cellular and developmental biology (MCDB) 153 medium in different ratios for keratinocyte growth. The keratinocyte viability will be measured by 3-(4,5-dimethyl-thiazol-2-yl)-2,5-diphenyltetrazolium bromide (MTT) assay to determine the optimum conditioned medium. From the study, 67% conditioned medium was supposed as the better medium for keratinocyte proliferation. In this experiment, the optimum cell density in feeder gel to coculture with keratinocytes is also determined as 1 x 10(5) cells/gel. Keratin 10 (K10) and Terminal Deoxynucleotidyl Transferase Mediated dUTP Nick End Labeling stain will be used to check the cell differentiation and apoptosis, respectively. The results suggest that keratinocytes should not be cultured in postconfluent conditions due to undesired apoptosis and differentiation. The result of cell viability from passages to passages shows that the optimum feeder gel plays a more important role to the keratinocyte proliferation than that of optimum conditioned medium. Keratinocytes cultured with optimum feeder gel in 67% conditioned medium could effectively promote proliferation, inhibit apoptosis, and prevent differentiation. The combination of conditioned media and feeder gel to culture keratinocytes without external supplements can provide an inexpensive way for keratinocyte proliferation and construct an environment for real-time communication between the two cells. The results conclude that keratinocyte cultivation in feeder gel with modified medium should be feasible in the production of high quality keratinocytes for skin equivalents preparation.
NASA Astrophysics Data System (ADS)
Papiol, V.; Cartes, J. E.; Fanelli, E.; Rumolo, P.
2013-03-01
The food-web structure and seasonality of the dominant taxa of benthopelagic megafauna (fishes and decapods) on the middle slope of the Catalan Sea (Balearic Basin, NW Mediterranean) were investigated using the carbon and nitrogen stable isotope ratios of 29 species. Macrofauna (infauna, suprabenthos and zooplankton) were also analysed as potential prey. Samples were collected on a seasonal basis from 600 to 1000 m depth between February 2007 and February 2008. The fishes and decapods were classified into feeding groups based on the literature: benthic feeders (including suprabenthos) and zooplankton feeders, the latter further separated into migratory and non-migratory species. Decapods exhibited depleted δ15N and enriched δ13C compared to fishes. Annual mean δ13C of fishes ranged from - 19.15‰ (Arctozenus risso) to - 16.65‰ (Phycis blennoides) and of δ15N from 7.27‰ (Lampanyctus crocodilus) to 11.31‰ (Nezumia aequalis). Annual mean values of δ13C of decapods were from - 18.94‰ (Sergestes arcticus) to - 14.78‰ (Pontophilus norvegicus), and of δ15N from 6.36‰ (Sergia robusta) to 9.72‰ (Paromola cuvieri). Stable isotopes distinguished well amongst the 3 feeding guilds established a priori, pointing to high levels of resource partitioning in deep-sea communities. The trophic structure of the community was a function of the position of predators along the benthic-pelagic gradient, with benthic feeders isotopically enriched relative to pelagic feeders. This difference allowed the identification of two food webs based on pelagic versus benthic consumption. Prey and predator sizes were also important in structuring the community. The most generalised seasonal pattern was δ13C depletion from winter to spring and summer, especially amongst migratory macroplankton feeders. This suggests greater consumption of pelagic prey, likely related with increases in pelagic production or with ontogenic migrations of organisms from mid-water to the Benthic Boundary Layer (BBL). δ15N enrichment was detected in periods of water column stratification, particularly amongst benthic feeder fishes. Megafauna relied on a single source of nutrition after peaks in surface production, presumably marine snow. Conversely, a larger array of food sources, probably from advection, sustained the community in periods of water column stratification. Benthic feeder δ13C values of both taxa were positively correlated with fluorescence measured 5 m above the seabed and negatively correlated with total organic carbon in the sediments, both being food sources for deposit feeding macroinfauna. Macroplankton feeder δ13C values were linked to environmental variables related to vertical transport from surface production, i.e. lipids and chlorophyll and their degradation products, likely due to their stronger reliance on sinking phytodetritus through consumption of planktonic prey.
DOE Office of Scientific and Technical Information (OSTI.GOV)
Holloway, Lawrence E.; Qu, Zhihua; Mohr-Schroeder, Margaret J.
In this study, we consider collaborative power systems education through the FEEDER consortium. To increase students' access to power engineering educational content, the consortium of seven universities was formed. A framework is presented to characterize different collaborative education activities among the universities. Three of these approaches of collaborative educational activities are presented and discussed. These include 1) cross-institutional blended courses ("MS-MD''); 2) cross-institutional distance courses ("SS-MD''); and 3) single-site special experiential courses and concentrated on-site programs available to students across consortium institutions ("MS-SD''). As a result, this paper presents the advantages and disadvantages of each approach.
Manuwoto, Svafrida; Scriber, J Mark
1986-05-01
The effects of tannins on survival, growth, and digestion were compared in two polyphagous species of Lepidoptera (one, the southern armyworm, a forb-feeder; and the other, the promethea silkmoth, a tree-feeder). Two different types of tannins (hydrolyzable and condensed) were incorporated into artificial basal diets in order to determine whether or not differential survival and growth would result between the forb feeder, which normally does not encounter tannins in its natural diet, and the tree-feeder, whose host species include many tanniniferous plants from several different families.Neonate larvae of the forb-feeding armyworms exhibited significantly suppressed 10-day growth rates at all tannin concentrations tested (0.5, 1.0, 1.5, 2.0, 2.5, and 3.0% of wet weight) for both the hydrolyzable and the condensed tannin compared to the control diet, however no dose-effect was detectable. In contrast, there were no detectable differences in neonate survival or growth through the first 10 days for the tree-feeding promethea silkmoth larvae fed diets with either tannic acid or quebracho tree condensed tannin.In order to determine the physiological mechanisms of action of these tannins against armyworms, we conducted detailed physiological bioassays of biomass and nitrogen utilization by penultimate instar larvae. Standard gravimetric feeding studies with both tannic acid and the quebracho tree condensed tannin demonstrated that reduced relative growth rates (RGR's) of Spodoptera eridania Cram. were due to the suppressed relative consumption rates (RCR's) and decreased conversion efficiencies (ECD's) rather than due to digestibility-reduction (as reflected by approximate digestibility, AD). As with the neonate larval growth rate suppression, there were no detectable dose responses at the different concentrations of tannic acid (0.25, 0.50, 0.75, 1.00, 2.50, and 5.0 percent) and condensed tannins from quebracho (0.25, 0.50, 0.75, 1.0, and 2.5 percent) in our penultimate instar studies.
LOADING REEL AND PERFECTO STRIP STOCK FEEDER FOR #84 WATERBURYFARREL ...
LOADING REEL AND PERFECTO STRIP STOCK FEEDER FOR #84 WATERBURY-FARREL (U.S. GOVERNMENT) PRESS. THIS CONTINUOUS-FEED, 2-DRAW, 100 TON PRESS IS ONE OF TWO IN THE U.S. UNDER CONTRACT WITH THE DEPARTMENT OF DEFENSE FOR PRODUCTION OF BULLET JACKETS AND CARTRIDGE CASINGS. - American Brass Foundry, 70 Sayre Street, Buffalo, Erie County, NY
USDA-ARS?s Scientific Manuscript database
The adaptation to feeder-independent growth of a pig embryonic stem cell-derived pancreatic cell line is described. The parental PICM-31 cell line, previously characterized as an exocrine pancreas cell line, was colony-cloned two times in succession resulting in the subclonal cell line, PICM-31A1. P...
Feeding the Elite: The Evolution of Elite Pathways from Star High Schools to Elite Universities
ERIC Educational Resources Information Center
LeTendre, Gerald K.; Gonzalez, Roger Geertz; Nomi, Takako
2006-01-01
During the last 50 years, private "feeder" schools in Japan came to dominate entry into elite colleges. Intense organizational competition shaped the organizational environment and changed the pathways available to social elites. Compared to Japan, elite private feeders in the US have failed to dominate pathways into elite colleges. In…
ERIC Educational Resources Information Center
National Sanitation Foundation, Ann Arbor, MI.
THE SCOPE OF THIS STANDARD COVERS ADJUSTABLE OUTPUT RATE CHEMICAL FEEDERS, WHETHER USED FOR SOLUTIONS, SLURRIES OR SOLIDS. IT ALSO INCLUDES AUXILIARY EQUIPMENT SUCH AS PUMPS, STRAINERS, TUBING CONNECTIONS, TANKS, INJECTION FITTINGS AND OTHER REQUIRED COMPONENTS. THE FEEDERS DESCRIBED ARE INTENDED TO BE DESIGNED AND USED SPECIFICALLY FOR CHEMICAL…
USDA-ARS?s Scientific Manuscript database
Feeder-cells of irradiated mouse fibroblasts are commonly used for, and are generally necessary for, the in vitro maintenance and growth of many fastidious cell types, particularly embryonic stem cells or induced pluripotent stem cells. Quantitative and semi-quantitative immunoassays were performed...
NASA Astrophysics Data System (ADS)
Imai, Koichi; Akasaka, Tsukasa; Watari, Fumio; Tanoue, Akito; Nakamura, Kazuaki; Suese, Kazuhiko; Takashima, Hiromasa; Nishikawa, Tetsunari; Tanaka, Akio; Takeda, Shoji
2012-09-01
The effects of nanomaterials on human reproduction and development remain unknown. The risks of nanomaterials for future generations should be elucidated. Thus, it is important to establish an experimental method to accurately examine embryotoxicity. We previously investigated the myocardial cell differentiation of ES-D3 cells using monolayer (SWCNTs) and multilayer (MWCNTs) nanocarbon tubes. As a result, in spite of having the same carbon composition, the effects on the cell differentiation levels differed between the tubes. We investigated their cell differentiation and cytotoxic effects on EL M3 and ES-R1-EGFP B2/EGFP cells, which require feeder cells. As a result, myocardial pulse rates differed between the presence of SWCNTs and MWCNTs even when feeder cells existed between the samples and cells. The different surface structures of SWCNTs and MWCNTs may have influenced ES cell differentiation.
10th European Zebrafish Meeting 2017, Budapest: Husbandry Workshop Summary.
Oltová, Jana; Barton, Carrie; Certal, Ana Catarina; Argenton, Francesco; Varga, Zoltán M
2018-01-02
A husbandry workshop on July 3, 2017, at the 10th European Zebrafish Meeting in Budapest, Hungary (July 3-July 7, 2017), focused on the standardization, optimization, and streamlining of fish facility procedures. Standardization can be achieved for example by developing novel software and hardware tools, such as a fish facility database for husbandry and environmental facility management (Zebrabase, Oltova), or a hand-held, air-pressurized fish feeder for consistent food distribution (Blowfish, Argenton). Streamlining is achieved when work hours are reduced, as with the standardized fish feeder, or by limiting the number and types of fish diets and observing the effect on animal welfare and performance (Barton). Testing the characteristics of new fish diets and observing whether they produce better experimental outcomes (Certal) optimizes diets and improves fish productivity. Collectively, the workshop presentations emphasized how consistency and harmonization of husbandry procedures within and across aquatic facilities yield reproducible scientific outcomes.
Norm-Optimal ILC Applied to a High-Speed Rack Feeder
NASA Astrophysics Data System (ADS)
Schindele, Dominik; Aschemann, Harald; Ritzke, Jöran
2010-09-01
Rack feeders as automated conveying systems for high bay rackings are of high practical importance. To shorten the transport times by using trajectories with increased kinematic values accompanying control measures for a reduction of the excited structural vibrations are necessary. In this contribution, the model-based design of a norm-optimal iterative learning control structure is presented. The rack feeder is modelled as an elastic multibody system. For the mathematical description of the bending deflections a Ritz ansatz is introduced. The tracking control design is performed separately for both axes using decentralised state space representations. Both the achievable performance and the resulting tracking accuracy of the proposed control concept are shown by measurement results from the experimental set-up.
Examining System-Wide Impacts of Solar PV Control Systems with a Power Hardware-in-the-Loop Platform
DOE Office of Scientific and Technical Information (OSTI.GOV)
Williams, Tess L.; Fuller, Jason C.; Schneider, Kevin P.
2014-06-08
High penetration levels of distributed solar PV power generation can lead to adverse power quality impacts, such as excessive voltage rise, voltage flicker, and reactive power values that result in unacceptable voltage levels. Advanced inverter control schemes have been developed that have the potential to mitigate many power quality concerns. However, local closed-loop control may lead to unintended behavior in deployed systems as complex interactions can occur between numerous operating devices. To enable the study of the performance of advanced control schemes in a detailed distribution system environment, a test platform has been developed that integrates Power Hardware-in-the-Loop (PHIL) withmore » concurrent time-series electric distribution system simulation. In the test platform, GridLAB-D, a distribution system simulation tool, runs a detailed simulation of a distribution feeder in real-time mode at the Pacific Northwest National Laboratory (PNNL) and supplies power system parameters at a point of common coupling. At the National Renewable Energy Laboratory (NREL), a hardware inverter interacts with grid and PV simulators emulating an operational distribution system. Power output from the inverters is measured and sent to PNNL to update the real-time distribution system simulation. The platform is described and initial test cases are presented. The platform is used to study the system-wide impacts and the interactions of inverter control modes—constant power factor and active Volt/VAr control—when integrated into a simulated IEEE 8500-node test feeder. We demonstrate that this platform is well-suited to the study of advanced inverter controls and their impacts on the power quality of a distribution feeder. Additionally, results are used to validate GridLAB-D simulations of advanced inverter controls.« less
Temporal characterization of small arms muzzle flash in the broadband visible
NASA Astrophysics Data System (ADS)
Burke, Tom; Bratlie, Duane
2010-04-01
The authors have developed a simple system for characterizing the muzzle flash duration of common military small-arms ammunition as a feeder for system design configurations. This paper is a synopsis of the efforts and results of the effort to characterize the broadband optical signature of modern small arms.
Modeling the Formation of Transverse Weld during Billet-on-Billet Extrusion
Mahmoodkhani, Yahya; Wells, Mary; Parson, Nick; Jowett, Chris; Poole, Warren
2014-01-01
A comprehensive mathematical model of the hot extrusion process for aluminum alloys has been developed and validated. The plasticity module was developed using a commercial finite element package, DEFORM-2D, a transient Lagrangian model which couples the thermal and deformation phenomena. Validation of the model against industrial data indicated that it gave excellent predictions of the pressure during extrusion. The finite element predictions of the velocity fields were post-processed to calculate the thickness of the surface cladding as one billet is fed in after another through the die (i.e., the transverse weld). The mathematical model was then used to assess the effect a change in feeder dimensions would have on the shape, thickness and extent of the transverse weld during extrusion. Experimental measurements for different combinations of billet materials show that the model is able to accurately predict the transverse weld shape as well as the clad surface layer to thicknesses of 50 μm. The transverse weld is significantly affected by the feeder geometry shape, but the effects of ram speed, billet material and temperature on the transverse weld dimensions are negligible. PMID:28788629
Cabrera-Marín, N V; Liedo, P; Vandame, R; Sánchez, D
2015-04-01
Agroecosystem management commonly involves the use of pesticides. As a result, a heterogeneous landscape is created, in which suitable and unsuitable spaces are defined by the absence/presence of pesticides. In this study, we explored how foragers of the honey bee, Apis mellifera L., adapt to such context. We specifically evaluated the effect of GF-120, a spinosad-based fruit fly toxic bait, on the allocation of foragers between food sources under the hypothesis that foragers will move from food sources with GF-120 to food sources without it. We thus carried out three experiments: in experiment 1, a group of foragers was trained to collect honey solution from a feeder; next, this feeder offered a GF-120/honey solution. A minority of foragers continued collecting the GF-120/honey solution. In experiment 2, we trained two groups of foragers from a colony to two food sources equally rewarding. Next, GF-120 was added to one of the food sources. We found that the majority of foragers moved from the GF-120-treated feeder to the feeder without GF-120 and that the minority that continued visiting the GF-120-treated feeder did not collect the GF-120/honey solution. In a third experiment, we wanted to know if foragers in an experimental setup as in experiment 1 would perform waggle dances: none of the foragers that collected GF-120/honey were observed dancing. Our results emphasize the importance of "food refuges" for non-target species, since they minimize the impact of agrochemicals upon them.
Abasi, M; Massumi, M; Riazi, G; Amini, H
2012-10-11
Parkinson's disease (PD) is a neurodegenerative disorder in which the nigro-striatal dopaminergic (DAergic) neurons have been selectively lost. Due to side effects of levodopa, a dopamine precursor drug, recently cell replacement therapy for PD has been considered. Lack of sufficient amounts of, embryos and ethical problems regarding the use of dopamine-rich embryonic neural cells have limited the application of these cells for PD cell therapy. Therefore, many investigators have focused on using the pluripotent stem cells to generate DAergic neurons. This study is aimed first to establish a mouse embryonic stem (mES) cell line that can stably co-express Nurr1 (Nuclear receptor subfamily 4, group A, member 2) transcription factor in order to efficiently generate DAergic neurons, and glutathione peroxidase-1 (GPX-1) to protect the differentiated DAergic-like cells against oxidative stress. In addition to genetic engineering of ES cells, the effect of Beta-boswellic acid (BBA) on DAergic differentiation course of mES cells was sought in the present study. To that end, the feeder-independent CGR8 mouse embryonic stem cells were transduced by Nurr1- and GPX-1-harboring Lentiviruses and the generated Nurr1/GPX-1-expresssing ES clones were characterized and verified. Gene expression analyses demonstrated that BBA treatment and overexpression of Nurr1 has a synergistic effect on derivation of DAergic neurons from Nurr1/GPX-1-expressing ES cells. The differentiated cells could exclusively synthesize and secrete dopamine in response to stimuli. Overexpression of GPX-1 in genetically engineered Nurr1/GPX-1-ES cells increased the viability of these cells during their differentiation into CNS stem cells. In conclusion, the results demonstrated that Nurr1-overexpressing feeder-independent ES cells like the feeder-dependent ES cells, can be efficiently programmed into functional DAergic neurons and additional treatment of cells by BBA can even augment this efficiency. GPX-1 overexpression in Nurr1/GPX-1-ES cells increases the viability of differentiated CNS stem-like cells. The result of this study may have impact on future stem cell therapy of PD. Copyright © 2012 IBRO. Published by Elsevier Ltd. All rights reserved.
Feasibility study of modern airships, phase 2. Volume 2: Airport feeder vehicle
NASA Technical Reports Server (NTRS)
1976-01-01
The Airport Feeder vehicle is a VTOL, semi-buoyant ellipsoidal airship capable of transporting passengers or cargo to major CTOL hub terminals from suburban and downtown depots. Six tasks were reviewed: (1) vehicle design definition, (2) operational procedures analysis, (3) cost analysis, (4) comparison with alternate transportation modes, (5) mission/vehicle feasibility assessment, and (6) technology assessment.
47 CFR 25.223 - Alternative licensing rules for feeder-link earth stations in the 17/24 GHz BSS.
Code of Federal Regulations, 2014 CFR
2014-10-01
... earth stations in the 17/24 GHz BSS. 25.223 Section 25.223 Telecommunication FEDERAL COMMUNICATIONS... Alternative licensing rules for feeder-link earth stations in the 17/24 GHz BSS. (a) This section applies to license applications for earth stations that transmit to 17/24 GHz Broadcasting-Satellite Service space...
ERIC Educational Resources Information Center
Scott, Thelma J.
The Developmental Career Guidance (DCG) project is a K-12 career guidance demonstration project operating at three high schools and 18 feeder schools in the Detroit Public School District. Directed from Wayne State University, DCG has centers at the high schools and each of the feeder schools. From the centers, students voluntarily can draw…
Federal Register 2010, 2011, 2012, 2013, 2014
2011-09-23
... galvanic corrosion. It was subsequently determined that the silver- plating is inadequate for this... microscopic galvanic corrosion on the ADG power feeder cable wires. * * * * * The proposed AD would require... feeder cables were damaged due to galvanic corrosion. It was subsequently determined that the silver...
Adelman, James S; Moyers, Sahnzi C; Farine, Damien R; Hawley, Dana M
2015-09-22
Individual heterogeneity can influence the dynamics of infectious diseases in wildlife and humans alike. Thus, recent work has sought to identify behavioural characteristics that contribute disproportionately to individual variation in pathogen acquisition (super-receiving) or transmission (super-spreading). However, it remains unknown whether the same behaviours enhance both acquisition and transmission, a scenario likely to result in explosive epidemics. Here, we examined this possibility in an ecologically relevant host-pathogen system: house finches and their bacterial pathogen, Mycoplasma gallisepticum, which causes severe conjunctivitis. We examined behaviours likely to influence disease acquisition (feeder use, aggression, social network affiliations) in an observational field study, finding that the time an individual spends on bird feeders best predicted the risk of conjunctivitis. To test whether this behaviour also influences the likelihood of transmitting M. gallisepticum, we experimentally inoculated individuals based on feeding behaviour and tracked epidemics within captive flocks. As predicted, transmission was fastest when birds that spent the most time on feeders initiated the epidemic. Our results suggest that the same behaviour underlies both pathogen acquisition and transmission in this system and potentially others. Identifying individuals that exhibit such behaviours is critical for disease management. © 2015 The Author(s).
Thermal analysis of the cryostat feed through for the ITER Tokamak TF feeder
NASA Astrophysics Data System (ADS)
Zhang, Shanwen; Song, Yuntao; Lu, Kun; Wang, Zhongwei; Zhang, Jianfeng; Qin, Yongfa
2017-04-01
In Tokamaks, the toroidal field (TF) coil feeder is an important component that is used to supply the cryogens and electrical power for the TF coils. As a part of the TF feeder, the cryostat-feed through (CFT) is subject to low temperatures of 9 and 80 K inside and room temperature of 300 K outside. Based on the features of the International Thermonuclear Experimental Reactor TF feeder, the thermal performance of the CFT under the nominal conditions is studied. Taking into account the conductive, convective and radiation heat transfer, the finite element model of the CFT is built. Transient thermal analysis is performed to determine the temperatures of the CFT on the 9th day of cooldown. The model is assessed by comparing the cooling curves of the CFT after 9 days. If the simulation and experimental results are the same, the finite element model can be considered as calibrated. The model predicts that the cooling time will be approximately 26 days and the temperature distribution and heat load of the main components are obtained when the CFT reaches thermal equilibrium. This study provides a valid quantitative characterization of the CFT design.
Hojo, Masato; Arakawa, Yoshiki; Funaki, Takeshi; Yoshida, Kazumichi; Kikuchi, Takayuki; Takagi, Yasushi; Araki, Yoshio; Ishii, Akira; Kunieda, Takeharu; Takahashi, Jun C; Miyamoto, Susumu
2014-01-01
Hemangioblastomas remain a surgical challenge because of their arteriovenous malformation-like character. Recently, indocyanine green (ICG) videoangiography has been applied to neurosurgical vascular surgery. The aim of this study was to evaluate the usefulness of tumor blood flow imaging by intraoperative ICG videoangiography in surgery for hemangioblastomas. Twenty intraoperative ICG videoangiography procedures were performed in 12 patients with hemangioblastomas. Seven lesions were located in the cerebellum, two lesions were in the medulla oblongata, and three lesions were in the spinal cord. Ten procedures were performed before or during dissection, and 10 procedures were performed after tumor resection. ICG videoangiography could provide dynamic images of blood flow in the tumor and its related vessels under surgical view. Interpretation of these dynamic images of tumor blood flow was useful for discrimination of transit feeders (feeders en passage) and also for estimation of unexposed feeders covered with brain parenchyma. Postresection ICG videoangiography could confirm complete tumor resection and normalized blood flow in surrounding vessels. In surgery for hemangioblastomas, careful interpretation of dynamic ICG images can provide useful information on transit feeders and unexposed hidden vessels that cannot be directly visualized by ICG. Copyright © 2014 Elsevier Inc. All rights reserved.
Urbanization affects neophilia and risk-taking at bird-feeders
NASA Astrophysics Data System (ADS)
Tryjanowski, Piotr; Møller, Anders Pape; Morelli, Federico; Biaduń, Waldemar; Brauze, Tomasz; Ciach, Michał; Czechowski, Paweł; Czyż, Stanisław; Dulisz, Beata; Goławski, Artur; Hetmański, Tomasz; Indykiewicz, Piotr; Mitrus, Cezary; Myczko, Łukasz; Nowakowski, Jacek J.; Polakowski, Michał; Takacs, Viktoria; Wysocki, Dariusz; Zduniak, Piotr
2016-06-01
Urban environments cover vast areas with a high density of humans and their dogs and cats causing problems for exploitation of new resources by wild animals. Such resources facilitate colonization by individuals with a high level of neophilia predicting that urban animals should show more neophilia than rural conspecifics. We provided bird-feeders across urban environments in 14 Polish cities and matched nearby rural habitats, testing whether the presence of a novel item (a brightly coloured green object made out of gum with a tuft of hair) differentially delayed arrival at feeders in rural compared to urban habitats. The presence of a novel object reduced the number of great tits Parus major, but also the total number of all species of birds although differentially so in urban compared to rural areas. That was the case independent of the potentially confounding effects of temperature, population density of birds, and the abundance of cats, dogs and pedestrians. The number of great tits and the total number of birds attending feeders increased in urban compared to rural areas independent of local population density of birds. This implies that urban birds have high levels of neophilia allowing them to readily exploit unpredictable resources in urban environments.
Wilson, K M; Bourassa, D V; McLendon, B L; Wilson, J L; Buhr, R J
2018-06-08
The impact of restrictive feeding programs on Salmonella and Campylobacter colonization and persistence after challenge was investigated for broiler breeder pullets housed in an experimental rearing facility. Pullet-chicks were placed on litter in 3 feeding program rooms and each room contained 2 replicate pens. The feeding programs were: (1) Skip-a-day in trough feeders (SAD); (2) Every-day in trough feeders (EDT); (3) Every-day on the pen litter (EDL). On d 1, an additional group of hatchmate chicks were housed in a separate room and gavaged with Salmonella Typhimurium, to later serve as seeder chicks. After seeders were confirmed Salmonella-positive at wk 4, at wk 5 seeders were placed into each feeding program pen to commingle with 135 penmates. At 7, 9, 11, 17, 18, and 20 wk the litter surface in each pen was sampled using intermittently stepped-on drag-swabs. At 8, 12, 16, and 20 wk of age the ceca were sampled from 10 penmates/pen and 2 pooled spleen samples/pen were collected. SAD litter remained Salmonella-positive through 20 wk of age while EDL and EDT pens had no detectible litter Salmonella recovery by 18 and 20 wk. EDL fed pens had no direct (<102 cfu/mL) litter Salmonella recovery during the entirety of the experiment. Salmonella prevalence for ceca from SAD pullets was significantly (P < 0.05) higher at 8 wk (70%) compared to EDT (40%) and EDL (30%). At wk 12, SAD pullets for both on and off-feed sampling days had significantly higher Salmonella recovery (40%), compared to EDT and EDL (both at 5% recovery). By 16 and 20 wk, only the SAD pullets on the on-feed day (48 h without feed) had recovery of Salmonella at 20%. Salmonella recovery in pooled spleen samples did not appear associated with feeding treatments (22% positive). The remaining pullets challenged with Campylobacter at 21 wk produced similar trends as was seen for Salmonella. SAD program pullets had significantly higher Campylobacter from ceca (80 to 100%) compared to pullets on EDL (30 to 60%) or EDT (40 to 95%). These results suggest that using a Skip-a-Day feeding program for broiler breeder pullets contributes to persistently higher Salmonella and Campylobacter ceca colonization and litter prevalence.
Considerations in the improvement of human epidermal keratinocyte culture in vitro.
Kaviani, Maryam; Geramizadeh, Bita; Rahsaz, Marjan; Marzban, Saeed
2015-04-01
Large-scale expansion of epidermal keratinocytes is essential in the application of these cells for severe burn treatment in patients. Therefore, this study was designed to evaluate various conditions in the expansion of human epidermal keratinocytes. The epidermis was separated from the dermis of skin samples using dispase. The epidermis was trypsinized for keratinocyte isolation. Keratinocytes were cultured in various conditions, with or without a human dermal fibroblast feeder layer, mitomycin C treatment, and different culture media. Our results suggest that keratinocytes cultured on a human dermal fibroblast feeder layer were grown for several passages. Extensive deformation and rapid deterioration were observed in the cultured cells without a feeder layer and in serum-free medium. Human dermal fibroblasts treated with mitomycin C can provide optimal conditions for proliferation of keratinocytes.
DOE Office of Scientific and Technical Information (OSTI.GOV)
Jumars, P.A.; Mayer, L.M.
1999-04-19
The authors assayed digestive capabilities of marine deposit feeders (animals that eat sediments) by using fluorescently tagged substrates and contact-angle measurements of surfactancy. Polychaetes on average showed higher enzyme activities and surfactancy than echinoderms. They found that surfactants produced by deposit feeders substantially enhance their abilities to solubilize hydrophobic pollutants such as polycyclic aromatic hydrocarbons (PAHs). Amounts solubilized were consistent with incorporation into micelles of the surfactant. Kinetics of PAH uptake could be explained by passive diffusion. The authors also found that the digestive strategies of deposit feeders often produce concentrations of proteins (digestive enzymes plus products of protein digestion)more » that are sufficient to solubilize metals. Histidine residues in these proteins were found to be critical for copper binding.« less
de Passillé, Anne Marie; Rushen, Jeffrey
2016-05-01
Dairy calves weaned off milk at an early age show signs of hunger and can lose weight. We examined whether using automated feeders to wean calves according to individual voluntary solid feed intake reduced the effects of weaning. Female Holstein calves were housed in groups of 5 to 9. All calves were fed 12 L/d milk and ad libitum grain starter and hay from automated feeders immediately after grouping, and were allocated to 3 weaning strategies: (1) early-weaned (EW; n=14): weaning began on d 40, and milk allowance gradually decreased until weaning was complete on d 48; (2) late-weaned (LW; n=14): weaning began on d 80 and was completed on d 89; (3) weaned by starter intake (WSI; n=28): weaning began when calves consumed 200g/d of starter and was completed when the calves consumed 1,400g/d. Each day, the automated feeders recorded quantities of milk, starter, and hay eaten by all calves, as well as the frequency of visits to the milk feeder; we used unrewarded visit frequency as a sign of hunger. Body weights (BW) were recorded weekly. We estimated daily digestible energy (DE) intake for each calf based on the milk, hay, and starter consumed. Average daily gains (ADG) were expressed as percent of BW. For calves in WSI, weaning began at 54.7±18.9 d (mean ± SD) of age, the duration of weaning was 21.1±10.6 d, and weaning ended at 75.8±10.7 d of age. Both LW and WSI calves had better ADG from wk 3 to 13 than EW calves. Calves in the WSI group drank less milk and ate more starter than LW calves but had similar ADG. During the period of weaning, EW calves made more unrewarded visits to the milk feeder than LW and WSI calves. Three EW calves lost weight during weaning, whereas all LW and WSI calves gained weight. Calves differ greatly in when they begin to eat solid feed and how quickly they increase the intake in response to a decrease in milk allowance. An advantage of automated feeders is that calves can be weaned at variable ages depending on their ability and willingness to eat solid feed, which reduces signs of hunger and improves weight gains during weaning. Copyright © 2016 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.
Razek, Ahmed Abdel Khalek Abdel; Gaballa, Gada; Megahed, Abdel Salam; Elmogy, Ebrahiem
2013-11-01
To evaluate vasculature of arteriovenous malformations (AVMs) of head and neck with time resolved imaging of contrast kinetics (TRICKS) MR angiography (MRA). Prospective study was conducted upon 19 patients (age range, 12-29 years; mean age 18 years; 10 males and 9 females) with AVM of head and neck. TRICKS-MRA of head and neck was performed during injection of contrast medium. Post processing with reconstruction of the images was done. Two independent readers assessed the overall TRICKS-MRA image quality score using a 5-point scale and depiction of the main arterial feeders, nidus, and venous drainage using 3 points scale. The Kappa test for interobserver agreement was done. The AVMs were evaluated morphologically in terms of number and origin of the main arterial feeders, the location and size of nidus either small (>2 cm) or large (>2 cm) and the draining veins into the superficial or deep venous drainage. The average TRICKS-MRA image quality score as judged by reader 1 was 3.89 ± 1.15 and that as judged by reader 2 was 3.89 ± 0.10, which yielded excellent interobserver agreement (k=0.77, 95% CI=0.53-0.98, r=0.78, P=0.001). The interobserver agreement of both readers was excellent for the arterial feeders (k=0.81, 95% CI=0.57-1.00, r=0.83, P=0.001), excellent for the nidus (k=0.91, 95% CI=0.75-1.00, r=0.92, P=0.001), and good for the venous drainage (k=0.77, 95% CI=0.53-0.98, r=0.78, P=0.001). The arterial feeders were single (n=14) or multiple (n=5), the nidus was large (n=16) or small (n=3) and the venous drainage was into the internal jugular (n=17) or the external jugular (n=2) veins. Three patients with small nidus and single arterial feeder were treated with sclerotherapy. Eleven patients with large nidus and single arterial feeder were referred for embolization. Combined embolization and surgery were done for five patients with large nidus and multiple arterial feeders. We concluded that TRICKS-MRA is a reliable non invasive tool for evaluation of the feeding arteries, the nidus and the draining veins of AVMs of head and neck. TRICKS-MRA can be used for evaluation and treatment planning of AVMs of head and neck. Copyright © 2013 Elsevier Ireland Ltd. All rights reserved.
NASA Technical Reports Server (NTRS)
Sellers, J. P.
1976-01-01
Analysis of the data heat pipe radiator systems tested in both vacuum and ambient environments was continued. The systems included (1) a feasibility VCHP header heat-pipe panel, (2) the same panel reworked to eliminate the VCHP feature and referred to as the feasibility fluid header panel, and (3) an optimized flight-weight fluid header panel termed the 'prototype.' A description of freeze-thaw thermal vacuum tests conducted on the feasibility VCHP was included. In addition, the results of ambient tests made on the feasibility fluid header are presented, including a comparison with analytical results. A thermal model of a fluid header heat pipe radiator was constructed and a computer program written. The program was used to make a comparison of the VCHP and fluid-header concepts for both single and multiple panel applications. The computer program was also employed for a parametric study, including optimum feeder heat pipe spacing, of the prototype fluid header.
47 CFR 25.202 - Frequencies, frequency tolerance and emission limitations.
Code of Federal Regulations, 2011 CFR
2011-10-01
... case-by-case basis. The Table follows: Space-to-earth(GHz) Earth-to-space(GHz) 3.65-3.7 17 12 19 5.091...-satellite service (space-to-Earth) is limited to feeder links for the mobile-satellite service. 9 The use of the band 17.3-17.8 GHz by the fixed-satellite service (Earth-to-space) is limited to feeder links for...
47 CFR 25.202 - Frequencies, frequency tolerance and emission limitations.
Code of Federal Regulations, 2010 CFR
2010-10-01
... case-by-case basis. The Table follows: Space-to-earth(GHz) Earth-to-space(GHz) 3.65-3.7 17 12 19 5.091...-satellite service (space-to-Earth) is limited to feeder links for the mobile-satellite service. 9 The use of the band 17.3-17.8 GHz by the fixed-satellite service (Earth-to-space) is limited to feeder links for...
47 CFR 25.202 - Frequencies, frequency tolerance and emission limitations.
Code of Federal Regulations, 2012 CFR
2012-10-01
... case-by-case basis. The Table follows: Space-to-earth(GHz) Earth-to-space(GHz) 3.65-3.7 17 12 19 5.091...-satellite service (space-to-Earth) is limited to feeder links for the mobile-satellite service. 9 The use of the band 17.3-17.8 GHz by the fixed-satellite service (Earth-to-space) is limited to feeder links for...
Aristizabal, F; Nieto, J; Yamout, S; Snyder, J
2014-07-01
Obesity and gastric ulceration are highly prevalent in horses. Management modifications for preventing squamous gastric ulceration include frequent feeding and free access to pasture; however, these practices may predispose horses to obesity. To compare the percentage of hay consumed, intragastric pH and horse activity between feeding from the ground and a hay grid feeder. Crossover experimental study. A pH electrode was inserted into the stomach to record the intragastric pH for 48 h. Horses received 1% of their body weight in grass hay twice a day. Horses were assigned to be fed from the ground or a commercial hay grid feeder for 24 h and then switched to the opposite protocol for an additional 24 h. Horses were continuously video-recorded and the percentage of time spent eating or drinking, walking or standing, and lying down were calculated. Two point data were compared by paired t test and pH over time was compared by repeated measures ANOVA. Horses consumed significantly greater amounts of grass hay when fed on the ground compared with a hay grid feeder (n = 9; P<0.001). There were no significant differences between the groups for mean intragastric pH values (n = 6; P = 0.97), mean intragastric pH over time (n = 6; P = 0.45) the length of time the pH was below 4.0 (n = 6; P = 0.54), and the percentage of time horses spent eating or drinking (n = 9; P = 0.52), walking or standing (n = 9; P = 0.3), or lying down (n = 9; P = 0.4). Within each group horses spent more time eating during the day compared with the night (n = 9; hay grid feeder P = 0.003; ground feeding P = 0.007). The hay grid feeder studied may be used to reduce the amount of hay ingested by horses without reducing the time horses spend eating. © 2013 EVJ Ltd.
James G. Conklin
1969-01-01
Native birches are subject to attack by insects at all stages of growth from the germinating seedling to the mature tree. All parts of the treeroots, stem, branches, foliage, and even the developing seedmay be utilized as feeding sites by insects of one kind or another. An enumeration of the many insects recorded in the literature as feeders on...
NASA Astrophysics Data System (ADS)
Levenson, SYa; Gendlina, LI; Kulikova, EG
2018-03-01
The paper reviews vibration feeders used to discharge storage reservoirs in mineral mining. In spotlight are vibrofeeders equipped with an active member of low flexural rigidity developed at Chinakal Institute of Mining. The authors present the results of the physical and numerical studies on vibratory discharge of cohesive rocks from a bunker.
Development of coal-feeding systems at the Morgantown Energy Research Center
NASA Technical Reports Server (NTRS)
Hobday, J. M.
1977-01-01
Systems for feeding crushed and pulverized coal into coal conversion reactor vessels are described. Pneumatic methods for feeding pulverized coal, slurry feeders, and coal pumps, methods for steam pickup, and a method for drying a water-coal slurry in a steam fluidized bed subsequent to feeding the coal into a reactor vessel are included.
1980-07-01
movements as feeders for rail and water transport, and to deliver fast service for high value freight. ( Creelman , 1979). Since the inland marine mode of...Development Work Group (1) Creelman , William A. Speech at Annual Meeting of the Transportation Research Board of the National Research Council. 1979. (2
Songbirds and Birds of Prey, Unit 6, Colorado Division of Wildlife.
ERIC Educational Resources Information Center
Hooper, Jon K.; Smith, Dwight R.
This booklet on songbirds and birds of prey is part of a series developed to encourage youth to pursue environmental projects. The manual explains bird anatomy and physiology, bird watching, types of feeders and shelter, and bird identification. Descriptions of feeding, hunting, and nesting habits are given for many species of birds. Also,…
Stephen W. Fraedrich; Michelle M. Cram
2002-01-01
A Longidorus species was consistently associated with patches of stunted and chlorotic loblolly pine seedlings at a forest-tree nursery in Georgia. Seedlings from affected areas had poorly developed root systems that lacked lateral and feeder roots. Longidorus population densities in composite soil samples from the margins of...
Singh, Rupinder; Gupta, Vivek; Ahuja, Chirag; Kumar, Ajay; Mukherjee, Kanchan K; Khandelwal, Niranjan
2018-06-01
Introduction The present study aimed to evaluate the accuracy of time-resolved-computed tomographic angiography (TR-CTA) on a 128-slice CT scanner vis-à-vis cerebral digital subtraction angiography (DSA) in defining the morphological and haemodynamic characteristics of cerebral arteriovenous malformation (AVM). Methods Twenty-one patients (age range 10-46, mean 24.8 years) with clinical suspicion of AVM and three patients (age range 23-35, mean 24.3 years) with diagnosed AVM who were on follow-up underwent DSA and TR-CTA, on average 1.5 days apart. Three independent neuroradiologists analysed both studies in a blinded fashion based on the following parameters: AVM location, arterial feeder territories, venous drainage pattern, nidus flow characteristics, venous outflow obstruction, arterial feeder enlargement, external carotid artery feeder, location of aneurysm if any, leptomeningeal and transdural recruitment, neoangiogenesis, and pseudophlebitic pattern. Results The TR-CTA correctly demonstrated AVM in all 21 positive cases. It concordantly detected location (21/21), venous drainage pattern (21/21), nidus flow characteristics (21/21), and the venous outflow obstruction (9/9). However, discordance was seen in the demonstration of the arterial feeder (2/45) ( p = 0.49), arterial enlargement (13/17) ( p = 0.103), external carotid artery feeder (0/1), aneurysmal location (3/5) ( p = 0.40), leptomeningeal recruitment (1/3) ( p = 0.40), neoangiogenesis (0/4) ( p = 0.028) and in the pseudophlebitic pattern (2/5) ( p = 0.167) demonstration. Conclusions The results suggest that TR-CTA can provide the important features of cerebral AVM which are required in patient management.
Egr-1: A Candidate Transcription Factor Involved in Molecular Processes Underlying Time-Memory.
Shah, Aridni; Jain, Rikesh; Brockmann, Axel
2018-01-01
In honey bees, continuous foraging is accompanied by a sustained up-regulation of the immediate early gene Egr-1 (early growth response protein-1) and candidate downstream genes involved in learning and memory. Here, we present a series of feeder training experiments indicating that Egr-1 expression is highly correlated with the time and duration of training even in the absence of the food reward. Foragers that were trained to visit a feeder over the whole day and then collected on a day without food presentation showed Egr-1 up-regulation over the whole day with a peak expression around 14:00. When exposed to a time-restricted feeder presentation, either 2 h in the morning or 2 h in the evening, Egr-1 expression in the brain was up-regulated only during the hours of training. Foragers that visited a feeder in the morning as well as in the evening showed two peaks of Egr-1 expression. Finally, when we prevented time-trained foragers from leaving the colony using artificial rain, Egr-1 expression in the brains was still slightly but significantly up-regulated around the time of feeder training. In situ hybridization studies showed that active foraging and time-training induced Egr-1 up-regulation occurred in the same brain areas, preferentially the small Kenyon cells of the mushroom bodies and the antennal and optic lobes. Based on these findings we propose that foraging induced Egr-1 expression can get regulated by the circadian clock after time-training over several days and Egr-1 is a candidate transcription factor involved in molecular processes underlying time-memory.
DOE Office of Scientific and Technical Information (OSTI.GOV)
Miyayama, Shiro, E-mail: s-miyayama@fukui.saiseikai.or.jp; Yamashiro, Masashi; Hattori, Yuki
2011-12-15
Purpose: To evaluate the origins of feeders of hepatocellular carcinoma (HCC) in the caudate lobe (S1). Materials and Methods: Eighty-eight HCCs (mean diameter 21.4 mm) were treated by chemoembolization. The tumor-feeding caudate artery was confirmed when a tumor stain was demonstrated on angiogram and iodized oil was accumulated into the HCC and S1 on computed tomography (CT). The origins were divided into R{sub 1} (right proximal), R{sub 2} (right distal), L{sub 1} (left proximal), L{sub 2} (left distal), A (anterior segmental), P (posterior segmental), M (middle hepatic or medial segmental), Ph (proper hepatic), Ch (common hepatic), and Ex (extrahepatic). Themore » origins of feeders supplying HCCs in the Spiegel lobe (SP; n = 36), the paracaval portion (PC; n = 38), and the caudate process (CP; n = 14) were also analyzed. Results: One hundred sixteen feeders were identified: 11 (9.5%) arose from R{sub 1}; 21 (18.1%) arose from R{sub 2}; nine arose (0.9%) from L{sub 1}; 15 (12.9%) arose from L{sub 2}; 24 (20.7%) arose from A; 25 (21.6%) arose from P; seven (6.0%) arose from M; one (0.9%) arose from Ph; and three (2.6%) arose from Ex. HCCs in the SP and the PC were fed by feeders from both hepatic arteries (the ratios of right to left were 3:2 and 3:1, respectively), and HCCs in the CP were dominantly fed by feeders from the right hepatic artery. Conclusion: The caudate artery most frequently arises from the right hepatic artery, followed with almost equal frequency by the left hepatic, the anterior segmental, and the posterior segmental artery. The origins of the caudate arteries differ according to the subsegmental locations.« less
Forget, Marie-Andrée; Malu, Shruti; Liu, Hui; Toth, Christopher; Maiti, Sourindra; Kale, Charuta; Haymaker, Cara; Bernatchez, Chantale; Huls, Helen; Wang, Ena; Marincola, Francesco M.; Hwu, Patrick; Cooper, Laurence J. N.; Radvanyi, Laszlo G.
2014-01-01
PURPOSE Adoptive cell therapy (ACT) with autologous tumor infiltrating lymphocytes (TIL) is a therapy for metastatic melanoma with response rates up to 50%. However, the generation of the TIL transfer product is challenging, requiring pooled allogeneic normal donor peripheral blood mononuclear cells (PBMC) used in vitro as “feeders” to support a rapid expansion protocol (REP). Here, we optimized a platform to propagate TIL to a clinical scale using K562-cells genetically modified to express costimulatory molecules such as CD86, CD137-ligand and membrane-bound IL-15 to function as artificial antigen-presenting cell (aAPC) as an alternative to using PBMC feeders. EXPERIMENTAL DESIGN We used aAPC or γ-irradiated PBMC feeders to propagate TIL and measured rates of expansion. The activation and differentiation state was evaluated by flow cytometry and differential gene expression analyses. Clonal diversity was assessed based on pattern of T-cell receptor (TCR) usage. T-cell effector function was measured by evaluation of cytotoxic granule content and killing of target cells. RESULTS The aAPC propagated TIL at numbers equivalent to that found with PBMC feeders, while increasing the frequency of CD8+ T-cell expansion with a comparable effector-memory phenotype. mRNA profiling revealed an up-regulation of genes in the Wnt and stem-cell pathways with the aAPC. The aAPC platform did not skew clonal diversity and CD8+ T cells showed comparable anti-tumor function as those expanded with PBMC feeders. CONCLUSIONS TIL can be rapidly expanded with aAPC to clinical scale generating T cells with similar phenotypic and effector profiles as with PBMC feeders. These data support the clinical-application of aAPC to manufacture TIL for the treatment of melanoma. PMID:25304728
Pérez-Barbería, F J; Gordon, I J
2001-05-22
In ungulates it is argued that specialization in the consumption of a particular type of food (feeding style) is reflected in morphological adaptations of the organs involved in the selection, processing and digestion of food. We analysed the differences in size and morphology of some oral traits that have been functionally related to food-selection ability (muzzle width, incisor-arcade shape, incisor shape), prehension of food (incisor protrusion), food comminution (molar occlusal surface area, hypsodonty (high-crowned molars)) and intake rate (incisor breadth) between ungulate species with different feeding styles (browser, mixed feeder, grazer). Grazers were characterized by large-body-size species. After controlling only for body mass, we found that grazers had wider muzzles and incisors, more-protruding incisors and more-bulky and higher-crowned molars than did mixed feeders and browsers. When the analyses took into account both body mass and phylogeny, only body mass and two out of the three hypsodonty indexes used remained significantly different between feeding styles. Browsers were smaller, on average, than mixed feeders and grazers, whilst grazers and mixed feeders did not differ in size. Also, browsers had shorter and less-bulky molars than did mixed feeders and grazers; the latter two feeding styles did not differ from each other in any of the hypsodonty indexes. We conclude that the adaptation to different dietary types in most of the oral traits studied is subsumed by the effects of body mass and the sharing of common ancestors. We hypothesize that differences in the ability to exploit different food resources primarily result from differences in body mass between species, and also discuss why hypsodonty characterizes feeding styles.
Pérez-Barbería, F. J.; Gordon, I. J.
2001-01-01
In ungulates it is argued that specialization in the consumption of a particular type of food (feeding style) is reflected in morphological adaptations of the organs involved in the selection, processing and digestion of food. We analysed the differences in size and morphology of some oral traits that have been functionally related to food-selection ability (muzzle width, incisor-arcade shape, incisor shape), prehension of food (incisor protrusion), food comminution (molar occlusal surface area, hypsodonty (high-crowned molars)) and intake rate (incisor breadth) between ungulate species with different feeding styles (browser, mixed feeder, grazer). Grazers were characterized by large-body-size species. After controlling only for body mass, we found that grazers had wider muzzles and incisors, more-protruding incisors and more-bulky and higher-crowned molars than did mixed feeders and browsers. When the analyses took into account both body mass and phylogeny, only body mass and two out of the three hypsodonty indexes used remained significantly different between feeding styles. Browsers were smaller, on average, than mixed feeders and grazers, whilst grazers and mixed feeders did not differ in size. Also, browsers had shorter and less-bulky molars than did mixed feeders and grazers; the latter two feeding styles did not differ from each other in any of the hypsodonty indexes. We conclude that the adaptation to different dietary types in most of the oral traits studied is subsumed by the effects of body mass and the sharing of common ancestors. We hypothesize that differences in the ability to exploit different food resources primarily result from differences in body mass between species, and also discuss why hypsodonty characterizes feeding styles. PMID:11375086
Maruyama, Junya; Matsunaga, Tamihide; Yamaori, Satoshi; Sakamoto, Sakae; Kamada, Noboru; Nakamura, Katsunori; Kikuchi, Shinji; Ohmori, Shigeru
2013-01-01
We reported previously that monkey embryonic stem cells (ESCs) were differentiated into hepatocytes by formation of embryoid bodies (EBs). However, this EB formation method is not always efficient for assays using a large number of samples simultaneously. A dispersion culture system, one of the differentiation methods without EB formation, is able to more efficiently provide a large number of feeder-free undifferentiated cells. A previous study demonstrated the effectiveness of the Rho-associated kinase inhibitor Y-27632 for feeder-free dispersion culture and induction of differentiation of monkey ESCs into neural cells. In the present study, the induction of differentiation of cynomolgus monkey ESCs (cmESCs) into hepatocytes was performed by the dispersion culture method, and the expression and drug inducibility of cytochrome P450 (CYP) enzymes in these hepatocytes were examined. The cmESCs were successfully differentiated into hepatocytes under feeder-free dispersion culture conditions supplemented with Y-27632. The hepatocytes differentiated from cmESCs expressed the mRNAs for three hepatocyte marker genes (α-fetoprotein, albumin, CYP7A1) and several CYP enzymes, as measured by real-time polymerase chain reaction. In particular, the basal expression of cmCYP3A4 (3A8) in these hepatocytes was detected at mRNA and enzyme activity (testosterone 6β-hydroxylation) levels. Furthermore, the expression and activity of cmCYP3A4 (3A8) were significantly upregulated by rifampicin. These results indicated the effectiveness of Y-27632 supplementation for feeder-free dispersed culture and induction of differentiation into hepatocytes, and the expression of functional CYP enzyme(s) in cmESC-derived hepatic cells.
Finn, Carol A.; Bedrosian, Paul A.; Cole, Janine; Khoza, Tshepo David; Webb, Susan J.
2015-01-01
Geophysical models image the 3D geometry of the mafic portion of the Bushveld Complex north of the Thabazimbi-Murchison Lineament (TML), critical for understanding the origin of the world's largest layered mafic intrusion and platinum group element deposits. The combination of the gravity and magnetic data with recent seismic, MT, borehole and rock property measurements powerfully constrains the models. The intrusion north of the TML is generally shallowly buried (generally <1500 m) with a modeled area of ∼160 km × ∼125 km. The modeled thicknesses are not well constrained but vary from ∼<1000 to >12,000 m, averaging ∼4000 m. A feeder, suggested by a large modeled thickness (>10,000 m) and funnel shape, for Lower Zone magmas could have originated near the intersection of NS and NE trending TML faults under Mokopane. The TML has been thought to be the feeder zone for the entire Bushveld Complex but the identification of local feeders and/or dikes in the TML in the models is complicated by uncertainties on the syn- and post-Bushveld deformation history. However, modeled moderately thick high density material near the intersection of faults within the central and western TML may represent feeders for parts of the Bushveld Complex if deformation was minimal. The correspondence of flat, high resistivity and density regions reflect the sill-like geometry of the Bushveld Complex without evidence for feeders north of Mokopane. Magnetotelluric models indicate that the Transvaal sedimentary basin underlies much of the Bushveld Complex north of the TML, further than previously thought and important because the degree of reaction and assimilation of the Transvaal rocks with the mafic magmas resulted in a variety of mineralization zones.
Herial, Nabeel A; Khan, Asif A; Sherr, Gregory T; Qureshi, Mushtaq H; Suri, M Fareed K; Qureshi, Adnan I
2015-09-01
The US Food and Drug Administration recently approved a detachable-tip microcatheter, the Apollo microcatheter (eV3, Inc, Irvine, California), to prevent catheter entrapment during embolization of brain arteriovenous malformations (AVMs) using liquid embolic systems. To report technical aspects and clinical results of cerebral embolizations with the Apollo microcatheter in 7 embolizations in 3 adult patients. A 62-year-old man presented with an AVM in the parieto-occipital region measuring 3.6 × 1.6 cm with major cortical feeders from the right middle cerebral artery (MCA) and minor contribution from the distal right anterior cerebral artery. Two pedicles originating from the MCA were embolized. A 48-year-old woman presented with a left frontal AVM measuring 3.3 × 1.8 cm with arterial feeders from the left MCA, left middle meningeal artery, and contralateral anterior cerebral artery. Three pedicles originating from the left MCA were embolized. A 76-year-old man presented with an arteriovenous fistula with multiple fistulous connections and feeders from both vertebral and occipital arteries and the left posterior cerebral artery draining into the left transverse, torcula, and left sigmoid sinus. Two major occipital artery feeders were embolized. Seven Apollo microcatheters were used with the Onyx 18 liquid embolic system. The length of the detachable tip was 15 mm in 2 and 30 mm in 5 embolizations. The mean microcatheter in-position time within the pedicle was 20 minutes. Detachment of tip occurred in 3 instances. No limitations in accessing target arterial feeders and safe tip disengagement were noted despite prolonged injection times. Our initial experience supports the feasibility, safety, and effectiveness of detachable-tip microcatheters in treating brain AVMs and arteriovenous fistulas.
Distribution of lead and cadmium in trophic levels of some marine organisms.
Mesmar, M
1987-01-01
The concentrations of lead and cadmium in two species of algae, two species of invertebrates, and one species of fish (from Fehmern Baltic Sea) were determined using atomic absorption spectrophotometry. The concentrations of these metals at the producer level (algae) were always higher than at the consumer level. Also, among the consumers there was an obvious difference according to feeding habits, in such a way that they could be ranked according to their high content of lead and cadmium as follows: filter feeder (detritous feeder), plankton feeder. In addition, distribution of lead and cadmium varied within the individual producer (Fucus vesiculosus) in such a way that the holdfast exhibited the highest concentration followed by the apcial tip and the branches of the first dichotomy was the lowest. This alga reflects clear selectivity in absorbing more lead than cadmium.
Large Scale Simulation Platform for NODES Validation Study
DOE Office of Scientific and Technical Information (OSTI.GOV)
Sotorrio, P.; Qin, Y.; Min, L.
2017-04-27
This report summarizes the Large Scale (LS) simulation platform created for the Eaton NODES project. The simulation environment consists of both wholesale market simulator and distribution simulator and includes the CAISO wholesale market model and a PG&E footprint of 25-75 feeders to validate the scalability under a scenario of 33% RPS in California with additional 17% of DERS coming from distribution and customers. The simulator can generate hourly unit commitment, 5-minute economic dispatch, and 4-second AGC regulation signals. The simulator is also capable of simulating greater than 10k individual controllable devices. Simulated DERs include water heaters, EVs, residential and lightmore » commercial HVAC/buildings, and residential-level battery storage. Feeder-level voltage regulators and capacitor banks are also simulated for feeder-level real and reactive power management and Vol/Var control.« less
Autonomous grain combine control system
Hoskinson, Reed L.; Kenney, Kevin L.; Lucas, James R.; Prickel, Marvin A.
2013-06-25
A system for controlling a grain combine having a rotor/cylinder, a sieve, a fan, a concave, a feeder, a header, an engine, and a control system. The feeder of the grain combine is engaged and the header is lowered. A separator loss target, engine load target, and a sieve loss target are selected. Grain is harvested with the lowered header passing the grain through the engaged feeder. Separator loss, sieve loss, engine load and ground speed of the grain combine are continuously monitored during the harvesting. If the monitored separator loss exceeds the selected separator loss target, the speed of the rotor/cylinder, the concave setting, the engine load target, or a combination thereof is adjusted. If the monitored sieve loss exceeds the selected sieve loss target, the speed of the fan, the size of the sieve openings, or the engine load target is adjusted.
DOE Office of Scientific and Technical Information (OSTI.GOV)
L. M. Dittmer
The 100-B-14:2 subsite encompasses the former sanitary sewer feeder lines associated with the 1607-B2 and 1607-B7 septic systems. Feeder lines associated with the 185/190-B building have also been identified as the 100-B-14:8 subsite, and feeder lines associated with the 1607-B7 septic system have also been identified as the 100-B-14:9 subsite. These two subsites have been administratively cancelled to resolve the redundancy. The results of verification sampling show that residual contaminant concentrations do not preclude any future uses and allow for unrestricted use of shallow zone soils. The results also demonstrate that residual contaminant concentrations are protective of groundwater and themore » Columbia River.« less
Locational Sensitivity Investigation on PV Hosting Capacity and Fast Track PV Screening
DOE Office of Scientific and Technical Information (OSTI.GOV)
Ding, Fei; Mather, Barry; Ainsworth, Nathan
A 15% PV penetration threshold is commonly used by utilities to define photovoltaic (PV) screening methods where PV penetration is defined as the ratio of total solar PV capacity on a line section to peak load. However, this method doesn't take into account PV locational impact or feeder characteristics that could strongly change the feeder's capability to host PVs. This paper investigates the impact of PV location and phase connection type on PV hosting capacity, and then proposes a fast-track PV screening approach that leverages various PV hosting capacity metric responding to different PV locations and types. The proposed studymore » could help utilities to evaluate PV interconnection requests and also help increase the PV hosting capacity of distribution feeders without adverse impacts on system voltages.« less
2012-09-13
pneumatically operated paste dumper and belt conveyor system, the loss in weight feeder system, the hydraulically operated shear roll mill, the pellet...out feed belt conveyor , and the pack out system comprised of the metal detector, scale, and pack out empty and full drum roller conveyors . Page | 4...feed hopper and conveyor supplying the loss in weight feeder were turned on, and it was verified that these items functioned as designed . The
Maronde, Carl P.; Killmeyer, Jr., Richard P.
1992-01-01
An apparatus for the disbursement of a bulk solid sample comprising, a gravity hopper having a top open end and a bottom discharge end, a feeder positioned beneath the gravity hopper so as to receive a bulk solid sample flowing from the bottom discharge end, and a conveyor receiving the bulk solid sample from the feeder and rotating on an axis that allows the bulk solid sample to disperse the sample to a collection station.
Maronde, Carl P.; Killmeyer JR., Richard P.
1992-03-03
An apparatus for the disbursement of a bulk solid sample comprising, a gravity hopper having a top open end and a bottom discharge end, a feeder positioned beneath the gravity hopper so as to receive a bulk solid sample flowing from the bottom discharge end, and a conveyor receiving the bulk solid sample from the feeder and rotating on an axis that allows the bulk solid sample to disperse the sample to a collection station.
Wear compensating seal means for rotary piston coal feeder
Gencsoy, Hasan T.; Gardner, John F.
1979-01-01
The present invention is directed to a wear compensating seal arrangement for use in a rotary piston feeder utilized for feeding pulverized coal into a gasifier operating at relatively high pressures and elevated temperatures. The rotary piston feeder has a circular casing with a coal loading opening therein diametrically opposed from a coal discharge and contains a rotatable disoidal rotor having a cylinder in which a reciprocatable piston is disposed. The reciprocation of the piston within the cylinder is provided by a stationary conjugate cam whereby pulverized coal from a coal hopper at atmospheric pressure can be introduced into the cylinder and then discharged therefrom into the high pressure gasifier while maintaining minimal losses of producer gas and the expenditure of minimal energy which would detract from the efficiency of the gasification. The seal arrangement of the present invention is disposed between the rotor and the casing about the coal discharge and prevents the high pressure gases from within the gasifier from escaping between these relatively movable parts during operation of the coal feeder. The seal utilizes a primary seal in contact with the rotor and a secondary seal supporting the primary seal. The primary seal is continuously urged towards the rotor by springs and the high pressure producer gas.
Ogilvy, Victoria; Fidgett, Andrea L; Preziosi, Richard F
2012-01-01
There are a limited number of feeder-invertebrates available to feed captive insectivores, and many are deficient in certain nutrients. Gut-loading is used to increase the diversity of nutrients present in the captive insectivore diet; however, little is known about delivery of carotenoids via gut-loading. Carotenoids may influence health and reproduction due to their roles in immune and antioxidant systems. We assessed interspecific variation in carotenoid accumulation and retention in three feeder-cricket species (Gryllus bimaculatus, Gryllodes sigillatus and Acheta domesticus) fed one of three diets (wheat-bran, fish-food based formulated diet, and fresh fruit and vegetables). Out of the three species of feeder-cricket in the fish-food-based dietary treatment group, G. bimaculatus had the greatest total carotenoid concentration. All cricket species fed the wheat-bran diet had very low carotenoid concentrations. Species on the fish-food-based diet had intermediate carotenoid concentrations, and those on the fruit and vegetable diet had the highest concentrations. Carotenoid retention was poor across all species. Overall, this study shows that, by providing captive insectivores with G. bimaculatus crickets recently fed a carotenoid-rich diet, the quantity of carotenoids in the diet can be increased. © 2011 Wiley Periodicals, Inc.
Lo Iacono, Melania; Anzalone, Rita; La Rocca, Giampiero; Baiamonte, Elena; Maggio, Aurelio; Acuto, Santina
2017-02-01
In recent years, umbilical cord blood (UCB) has been widely used as an alternative source to bone marrow (BM) for transplantation of hematopoietic stem and progenitor cells (HSPCs) in a variety of hematological and non-hematological disorders. Nevertheless, the insufficient number of UCB-HSPCs for graft represents a major challenge. HSPCs ex vivo expansion prior to transplantation is a valid strategy to overcome this limit. Several attempts to optimize the expansion conditions have been reported, including the use of mesenchymal stromal cells (MSCs) as feeder layer. Wharton's Jelly (WJ), the main component of umbilical cord (UC) matrix, is especially rich in MSCs, which are considered ideal candidates for feeder layer in co-culture systems. In fact, they can be easily harvested and grow robustly in culture, producing a confluent monolayer in a short time. Similarly to bone marrow-mesenchymal stromal cells (BM-MSCs), WJ-derived MSCs (WJ-MSCs) have been used to support hematopoiesis in vitro and in vivo. Here, we review the rationale for using MSCs, particularly WJ-MSCs, as a feeder layer for UCB-HSPCs ex vivo expansion. In addition, we report the main findings attesting the use of these MSCs as a support in hematopoiesis.
Digital optical feeder links system for broadband geostationary satellite
NASA Astrophysics Data System (ADS)
Poulenard, Sylvain; Mège, Alexandre; Fuchs, Christian; Perlot, Nicolas; Riedi, Jerome; Perdigues, Josep
2017-02-01
An optical link based on a multiplex of wavelengths at 1.55μm is foreseen to be a valuable solution for the feeder link of the next generation of high-throughput geostationary satellite. The main satellite operator specifications for such link are an availability of 99.9% over the year, a capacity around 500Gbit/s and to be bent-pipe. Optical ground station networks connected to Terabit/s terrestrial fibers are proposed. The availability of the optical feeder link is simulated over 5 years based on a state-of-the-art cloud mask data bank and an atmospheric turbulence strength model. Yearly and seasonal optical feeder link availabilities are derived and discussed. On-ground and on-board terminals are designed to be compliant with 10Gbit/s per optical channel data rate taking into account adaptive optic systems to mitigate the impact of atmospheric turbulences on single-mode optical fiber receivers. The forward and return transmission chains, concept and implementation, are described. These are based on a digital transparent on-off keying optical link with digitalization of the DVB-S2 and DVB-RCS signals prior to the transmission, and a forward error correcting code. In addition, the satellite architecture is described taking into account optical and radiofrequency payloads as well as their interfaces.
Maoz, Yonatan; Gal, Shira; Argov, Yael; Domeratzky, Sylvie; Coll, Moshe; Palevsky, Eric
2016-05-01
Antagonistic interactions among predators with shared prey are thought to hamper their ability to suppress herbivores. Our aim was to quantify intraguild interactions in omnivorous predatory mite assemblages in the presence of pollen, and assess their effect on pest populations. We focused on the following naturally occurring phytoseiid species in Israeli citrus orchards and their ability to suppress a key pest, the citrus rust mite (CRM) Phyllocoptruta oleivora (Eriophyidae): the generalists Amblyseius swirskii and Typhlodromus athiasae and the specialised pollen feeders Iphiseius degenerans, Euseius scutalis, E. stipulatus and E. victoriensis. Evaluations were performed on two spatial scales, tree seedlings and leaf discs. On seedlings, experiments were conducted to quantify the interactions between predators in the presence of pollen and its effects on CRM suppression. On leaf discs, intraguild interactions were studied between pairs of phytoseiid species in the presence of pollen without CRM. On seedlings, the specialised pollen predators were more effective at suppressing CRM populations than the generalist predators. In most cases, the more aggressive intraguild predator was the specialised pollen feeder. Similarly, leaf-disc experiments suggest that in these interactions the specialised pollen feeders tend to be the intraguild predators more often than the intraguild prey. © 2015 Society of Chemical Industry.
NASA Astrophysics Data System (ADS)
Clayton, N.; Crouchen, M.; Evans, D.; Gung, C.-Y.; Su, M.; Devred, A.; Piccin, R.
2017-12-01
The high voltage (HV) insulation on the ITER magnet feeder superconducting busbars and current leads will be prepared from S-glass fabric, pre-impregnated with an epoxy resin, which is interleaved with polyimide film and wrapped onto the components and cured during feeder manufacture. The insulation architecture consists of nine half-lapped layers of glass/Kapton, which is then enveloped in a ground-screen, and two further half-lapped layers of glass pre-preg for mechanical protection. The integrity of the HV insulation is critical in order to inhibit electrical arcs within the feeders. The insulation over the entire length of the HV components (bus bar, current leads and joints) must provide a level of voltage isolation of 30 kV. In operation, the insulation on ITER busbars will be subjected to high mechanical loads, arising from Lorentz forces, and in addition will be subjected to fretting erosion against stainless steel clamps, as the pulsed nature of some magnets results in longitudinal movement of the busbar. This work was aimed at assessing the wear on, and the changes in, the electrical properties of the insulation when subjected to typical ITER operating conditions. High voltage tests demonstrated that the electrical isolation of the insulation was intact after the fretting test.
Construction of Artificial Hepatic Lobule-Like Spheroids on a Three-Dimensional Culture Device.
Enosawa, Shin; Miyamoto, Yoshitaka; Kubota, Hisayo; Jomura, Tomoko; Ikeya, Takeshi
2012-01-01
One major purpose of cell culture is the reconstruction of physiological structures. Using bovine aortic epithelium cell line HH (JCRB0099) as feeder cells and rat primary hepatocytes, we constructed hepatic lobule-like spheroids on a cell array plate designed for three-dimensional (3D) culture. Microfabricated patterning of the cell array with poly(ethyleneglycol) brushes promotes the formation of spheroids at 100-μm diameter at 100-μm intervals. Our standard protocol is to seed with feeder HH cells and then seed with primary hepatic parenchymal cells. The composite cell spheroids thus obtained are called heterospheroids. Feeder cells that were attached to the plate migrated and encompassed the spheroidal hepatocyte mass. Electron microscopy revealed Disse space-like structures characterized by hepatocyte-rooted microvilli rooted between hepatocyte and feeder epithelial HH cells. Differentiated hepatic functions such as albumin synthesis and cytochrome P450 subfamily CYP3A activities were maintained for 28 days in the heterospheroid versus monospheroid and monolayer cultures. In addition, glucuronide conjugation activity was maintained at a high level in heterospheroids. These results indicate that structurally similar hepatic lobules were formed in a microfabricated cell array coculture system and that the culture conditions are beneficial for maintaining differentiated hepatic functions.
Assessment of sedimentary Cu availability: A comparison of biomimetic and AVS approaches
DOE Office of Scientific and Technical Information (OSTI.GOV)
Chen, Z.; Mayer, L.M.
1999-02-15
Sedimentary Cu bioavailability during deposit feeding is determined by both the digestive physiology of the organisms and the geochemistry of the sediments. The authors assessed the contribution of these two factors by using a biomimetic approach involving extraction of Cu with digestive fluids of two deposit feeders and one suspension feeder and a geochemical approach measuring Cu associated with acid-volatile sulfide (AVS) in sediments. Cu bioavailability determined by the biomimetic method varied among species with varying digestive physiology but all showed a marked increase when SEM{sub Cu}-AVS {ge} 0, corroborating the premise underlying the AVS method in determining sedimentary Cumore » bioavailability. The existence of a positive SEM{sub Cu}-AVS threshold suggests the existence of additional Cu-binding phases or mixed Cu(I)--Cu(II) sulfides in sediments. In addition, Cu bioavailable to digestive fluids was much less than that measured as SEM{sub Cu}-AVS, indicating that the AVS method overestimates Cu bioavailability to digestive fluid of deposit feeders. Incubation of digestive fluids with two Cu-bound model phases, goethite and sulfide, corroborated the relative unavailability of sulfide-bound Cu. Subsurface deposit feeders feeding on anoxic sediments may be exposed to less Cu than their surface-feeding counterparts in Cu-contaminated environments.« less
Mechanical Technology Development on A 35-m Deployable Radar Antenna for Monitoring Hurricanes
NASA Technical Reports Server (NTRS)
Fang, Houfei; Im, Eastwood
2006-01-01
The NEXRAD in Space project develops a novel instrument concept and the associated antenna technologies for a 35-GHz Doppler radar to monitor hurricanes, cyclones, and severe storms from a geostationary orbit. Mechanical challenges of this concept include a 35-m diameter lightweight in space deployable spherical reflector and a feeder scanning mechanism. The feasibility of using shape memory polymer material to develop the large deployable reflector has been investigated by this study. A spiral scanning mechanism concept has been developed and demonstrated by an engineering model.
NASA Astrophysics Data System (ADS)
Johnson, Anthony
2009-03-01
The Bell Labs Cooperative Research Fellowship Program for Minorities (CRFP), founded in 1972 was one of the first programs of its kind in the US to address the issue of under-representation of minorities in the fields of engineering, mathematics and science. As of 2000, well over 100 PhDs graduated with CRFP sponsorship and a significant fraction joined the research ranks of Bell Labs. In the early days of the program as much as 50% of African American PhDs in Physics in the US were granted to students supported by CRFP. Another unique program initiated by Bell Labs in 1974 that introduced undergraduate students to cutting edge research was the Summer Research Program for Minorities and Women (SRP). The SRP served as a natural feeder to the CRFP. Personally, my career in Optical Physics owes its foundation to these programs and I will give my perspective on participation and impact of the Bell Labs SRP (1974) and CRFP (1975) programs. The Meyerhoff Scholars Program at UMBC was developed in 1988. At that time, UMBC was graduating fewer than 18 African-American STEM majors per year. In 1996 the program was opened to all students with an interest in the advancement of minorities in STEM fields. The program enjoys an overall 18-year retention rate of greater than 95% and has over 500 graduates since 1993. As of May 2006, 75% of these graduates are enrolled in graduate and/or professional programs, with 49 PhDs and 20 MD/PhDs completed as of August 2006. The program challenges notions about minority achievement. Meyerhoff Scholars have changed the perceptions of those around them -- the expectations of faculty who instruct them, the attitudes of students who learn beside them, and the perspectives of scientists who engage them in research.
Smith, Michelle J; Webber, Beau R; Mohtashami, Mahmood; Stefanski, Heather E; Zúñiga-Pflücker, Juan Carlos; Blazar, Bruce R
2015-11-01
T lymphocytes are critical mediators of the adaptive immune system and have the capacity to serve as therapeutic agents in the areas of transplant and cancer immunotherapy. While T cells can be isolated and expanded from patients, T cells derived in vitro from both hematopoietic stem/progenitor cells (HSPCs) and human pluripotent stem cells (hPSCs) offer great potential advantages in generating a self-renewing source of T cells that can be readily genetically modified. T-cell differentiation in vivo is a complex process requiring tightly regulated signals; providing the correct signals in vitro to induce T-cell lineage commitment followed by their development into mature, functional, single positive T cells, is similarly complex. In this review, we discuss current methods for the in vitro derivation of T cells from murine and human HSPCs and hPSCs that use feeder-cell and feeder-cell-free systems. Furthermore, we explore their potential for adoption for use in T-cell-based therapies. © 2015 AlphaMed Press.
Nakagawa, Masato; Taniguchi, Yukimasa; Senda, Sho; Takizawa, Nanako; Ichisaka, Tomoko; Asano, Kanako; Morizane, Asuka; Doi, Daisuke; Takahashi, Jun; Nishizawa, Masatoshi; Yoshida, Yoshinori; Toyoda, Taro; Osafune, Kenji; Sekiguchi, Kiyotoshi; Yamanaka, Shinya
2014-01-01
In order to apply human embryonic stem cells (hESCs) and induced pluripotent stem cells (hiPSCs) to regenerative medicine, the cells should be produced under restricted conditions conforming to GMP guidelines. Since the conventional culture system has some issues that need to be addressed to achieve this goal, we developed a novel culture system. We found that recombinant laminin-511 E8 fragments are useful matrices for maintaining hESCs and hiPSCs when used in combination with a completely xeno-free (Xf) medium, StemFit™. Using this system, hESCs and hiPSCs can be easily and stably passaged by dissociating the cells into single cells for long periods, without any karyotype abnormalities. Human iPSCs could be generated under feeder-free (Ff) and Xf culture systems from human primary fibroblasts and blood cells, and they possessed differentiation abilities. These results indicate that hiPSCs can be generated and maintained under this novel Ff and Xf culture system. PMID:24399248
Saha, Krishanu; Mei, Ying; Reisterer, Colin M; Pyzocha, Neena Kenton; Yang, Jing; Muffat, Julien; Davies, Martyn C; Alexander, Morgan R; Langer, Robert; Anderson, Daniel G; Jaenisch, Rudolf
2011-11-15
The current gold standard for the culture of human pluripotent stem cells requires the use of a feeder layer of cells. Here, we develop a spatially defined culture system based on UV/ozone radiation modification of typical cell culture plastics to define a favorable surface environment for human pluripotent stem cell culture. Chemical and geometrical optimization of the surfaces enables control of early cell aggregation from fully dissociated cells, as predicted from a numerical model of cell migration, and results in significant increases in cell growth of undifferentiated cells. These chemically defined xeno-free substrates generate more than three times the number of cells than feeder-containing substrates per surface area. Further, reprogramming and typical gene-targeting protocols can be readily performed on these engineered surfaces. These substrates provide an attractive cell culture platform for the production of clinically relevant factor-free reprogrammed cells from patient tissue samples and facilitate the definition of standardized scale-up friendly methods for disease modeling and cell therapeutic applications.
Garner, J P; Kiess, A S; Mench, J A; Newberry, R C; Hester, P Y
2012-07-01
Hen performance can be affected by many interacting variables related to cage design, such as floor area, height, tier arrangement, and feeder and drinker type and placement within the cage. Likewise, features of house design such as waste management and lighting can also affect hen productivity. The influence of these design aspects on hen performance has not been fully assessed. Determining the effects of numerous, interacting variables is impractical in a traditional experiment; therefore, an epidemiological approach, using variability in cage and house design among and within commercial producers, was employed to identify features that affect egg production and egg weight. A universal cage measurement system was created to calculate cage design variables. A database for recording information on cage design, resource location, waste management, environmental conditions, and hen productivity was developed. Production outcomes were assessed from placement to 60 wk of age in White Leghorns (n = 165-168 houses). Using GLM, a statistical model was identified that best described the variance in egg traits. Eggs/hen-housed increased with greater feeder space allocation (P = 0.031); taller cages (P = 0.029); rear (vs. front) drinker location in vertical cages (P = 0.026); and regular removal of manure from the house (P = 0.005). Case weight of eggs was greater in A-frame houses where manure was removed regularly instead of being left in the house (P < 0.001); with increasing cage floor slope (P = 0.001); in cages where drinkers were placed more toward the front or back of the cage as compared with the middle of the cage (P < 0.001); with more space/hen (P = 0.024); and with higher caloric intake (P < 0.001). Perhaps because of its negative correlation with egg production, case weight of eggs increased with less feeder space allocation (P = 0.004) and shorter cage heights (P < 0.001). These results reveal important effects of feeder space, floor space, cage height, drinker position, and waste management on hen productivity.
Factors affecting body weight loss during commercial long haul transport of cattle in North America.
González, L A; Schwartzkopf-Genswein, K S; Bryan, M; Silasi, R; Brown, F
2012-10-01
The objective of the present study was to identify and quantify several factors affecting shrink in cattle during commercial long-haul transport (≥400 km; n = 6,152 journeys). Surveys were designed and delivered to transport carriers to collect relevant information regarding the characteristics of animals, time of loading, origin and destination, and loaded weight before and after transport. In contrast to fat cattle, feeder cattle exhibited greater shrink (4.9 vs. 7.9 ± 0.2% of BW, respectively; P < 0.01), and experienced longer total transport durations (12.4 vs. 14.9 ± 0.99, respectively; P < 0.01) due to border crossing protocols which require mandatory animal inspection. Shrink was greater (P < 0.001) for feeder cattle loaded at ranches/farms and feed yards compared with those loaded at auction markets. Cattle loaded during the afternoon and evening shrank more than those loaded during the night and morning (P < 0.05). Shrinkage was less in cattle transported by truck drivers having 6 or more years of experience hauling livestock compared with those with 5 yr or less (P < 0.05). Shrink increased with both midpoint ambient temperature (% of BW/°C; P < 0.001) and time on truck (% of BW/h; P < 0.001). Temperature and time on truck had a multiplicative effect on each other because shrink increased most rapidly in cattle transported for both longer durations and at higher ambient temperatures (P < 0.001). The rate of shrink over time (% of BW/h) was greatest in cull cattle, intermediate in calves and feeder cattle, and slowest in fat cattle (P < 0.05) but such differences disappeared when the effects of place of origin, loading time, and experience of truck drivers were included in the model. Cull cattle, calves and feeder cattle appear to be more affected by transport compared with fat cattle going to slaughter because of greater shrink. Several factors should be considered when developing guidelines to reduce cattle transport stress and shrink including type of cattle, ambient temperature, transport duration, driving quality, and time and origin of loading.
Muirhead, James D.; Van Eaton, Alexa R.; Re, Giuseppe; White, James D. L.; Ort, Michael H.
2016-01-01
Although monogenetic volcanic fields pose hazards to major cities worldwide, their shallow magma feeders (<500 m depth) are rarely exposed and, therefore, poorly understood. Here, we investigate exposures of dikes and sills in the Hopi Buttes volcanic field, Arizona, to shed light on the nature of its magma feeder system. Shallow exposures reveal a transition zone between intrusion and eruption within 350 m of the syn-eruptive surface. Using a combination of field- and satellite-based observations, we have identified three types of shallow magma systems: (1) dike-dominated, (2) sill-dominated, and (3) interconnected dike-sill networks. Analysis of vent alignments using the pyroclastic massifs and other eruptive centers (e.g., maar-diatremes) shows a NW-SE trend, parallel to that of dikes in the region. We therefore infer that dikes fed many of the eruptions. Dikes are also observed in places transforming to transgressive (ramping) sills. Estimates of the observable volume of dikes (maximum volume of 1.90 × 106 m3) and sills (minimum volume of 8.47 × 105 m3) in this study reveal that sills at Hopi Buttes make up at least 30 % of the shallow intruded volume (∼2.75 × 106 m3 total) within 350 m of the paeosurface. We have also identified saucer-shaped sills, which are not traditionally associated with monogenetic volcanic fields. Our study demonstrates that shallow feeders in monogenetic fields can form geometrically complex networks, particularly those intruding poorly consolidated sedimentary rocks. We conclude that the Hopi Buttes eruptions were primarily fed by NW-SE-striking dikes. However, saucer-shaped sills also played an important role in modulating eruptions by transporting magma toward and away from eruptive conduits. Sill development could have been accompanied by surface uplifts on the order of decimeters. We infer that the characteristic feeder systems described here for the Hopi Buttes may underlie monogenetic fields elsewhere, particularly where magma intersects shallow, and often weak, sedimentary rocks. Results from this study support growing evidence of the important role of shallow sills in active monogenetic fields.
DOE Office of Scientific and Technical Information (OSTI.GOV)
Sparn, Bethany F; Ruth, Mark F; Krishnamurthy, Dheepak
Many have proposed that responsive load provided by distributed energy resources (DERs) and demand response (DR) are an option to provide flexibility to the grid and especially to distribution feeders. However, because responsive load involves a complex interplay between tariffs and DER and DR technologies, it is challenging to test and evaluate options without negatively impacting customers. This paper describes a hardware-in-the-loop (HIL) simulation system that has been developed to reduce the cost of evaluating the impact of advanced controllers (e.g., model predictive controllers) and technologies (e.g., responsive appliances). The HIL simulation system combines large-scale software simulation with a smallmore » set of representative building equipment hardware. It is used to perform HIL simulation of a distribution feeder and the loads on it under various tariff structures. In the reported HIL simulation, loads include many simulated air conditioners and one physical air conditioner. Independent model predictive controllers manage operations of all air conditioners under a time-of-use tariff. Results from this HIL simulation and a discussion of future development work of the system are presented.« less
Kanke, Kosuke; Masaki, Hideki; Saito, Taku; Komiyama, Yuske; Hojo, Hironori; Nakauchi, Hiromitsu; Lichtler, Alexander C; Takato, Tsuyoshi; Chung, Ung-Il; Ohba, Shinsuke
2014-06-03
Pluripotent stem cells are a promising tool for mechanistic studies of tissue development, drug screening, and cell-based therapies. Here, we report an effective and mass-producing strategy for the stepwise differentiation of mouse embryonic stem cells (mESCs) and mouse and human induced pluripotent stem cells (miPSCs and hiPSCs, respectively) into osteoblasts using four small molecules (CHIR99021 [CHIR], cyclopamine [Cyc], smoothened agonist [SAG], and a helioxanthin-derivative 4-(4-methoxyphenyl)pyrido[4',3':4,5]thieno[2,3-b]pyridine-2-carboxamide [TH]) under serum-free and feeder-free conditions. The strategy, which consists of mesoderm induction, osteoblast induction, and osteoblast maturation phases, significantly induced expressions of osteoblast-related genes and proteins in mESCs, miPSCs, and hiPSCs. In addition, when mESCs defective in runt-related transcription factor 2 (Runx2), a master regulator of osteogenesis, were cultured by the strategy, they molecularly recapitulated osteoblast phenotypes of Runx2 null mice. The present strategy will be a platform for biological and pathological studies of osteoblast development, screening of bone-augmentation drugs, and skeletal regeneration.
Multi-Time Step Service Restoration for Advanced Distribution Systems and Microgrids
Chen, Bo; Chen, Chen; Wang, Jianhui; ...
2017-07-07
Modern power systems are facing increased risk of disasters that can cause extended outages. The presence of remote control switches (RCSs), distributed generators (DGs), and energy storage systems (ESS) provides both challenges and opportunities for developing post-fault service restoration methodologies. Inter-temporal constraints of DGs, ESS, and loads under cold load pickup (CLPU) conditions impose extra complexity on problem formulation and solution. In this paper, a multi-time step service restoration methodology is proposed to optimally generate a sequence of control actions for controllable switches, ESSs, and dispatchable DGs to assist the system operator with decision making. The restoration sequence is determinedmore » to minimize the unserved customers by energizing the system step by step without violating operational constraints at each time step. The proposed methodology is formulated as a mixed-integer linear programming (MILP) model and can adapt to various operation conditions. Furthermore, the proposed method is validated through several case studies that are performed on modified IEEE 13-node and IEEE 123-node test feeders.« less
Sequential Service Restoration for Unbalanced Distribution Systems and Microgrids
Chen, Bo; Chen, Chen; Wang, Jianhui; ...
2017-07-07
The resilience and reliability of modern power systems are threatened by increasingly severe weather events and cyber-physical security events. An effective restoration methodology is desired to optimally integrate emerging smart grid technologies and pave the way for developing self-healing smart grids. In this paper, a sequential service restoration (SSR) framework is proposed to generate restoration solutions for distribution systems and microgrids in the event of large-scale power outages. The restoration solution contains a sequence of control actions that properly coordinate switches, distributed generators, and switchable loads to form multiple isolated microgrids. The SSR can be applied for three-phase unbalanced distributionmore » systems and microgrids and can adapt to various operation conditions. Mathematical models are introduced for three-phase unbalanced power flow, voltage regulators, transformers, and loads. Furthermore, the SSR problem is formulated as a mixed-integer linear programming model, and its effectiveness is evaluated via the modified IEEE 123 node test feeder.« less
Sequential Service Restoration for Unbalanced Distribution Systems and Microgrids
DOE Office of Scientific and Technical Information (OSTI.GOV)
Chen, Bo; Chen, Chen; Wang, Jianhui
The resilience and reliability of modern power systems are threatened by increasingly severe weather events and cyber-physical security events. An effective restoration methodology is desired to optimally integrate emerging smart grid technologies and pave the way for developing self-healing smart grids. In this paper, a sequential service restoration (SSR) framework is proposed to generate restoration solutions for distribution systems and microgrids in the event of large-scale power outages. The restoration solution contains a sequence of control actions that properly coordinate switches, distributed generators, and switchable loads to form multiple isolated microgrids. The SSR can be applied for three-phase unbalanced distributionmore » systems and microgrids and can adapt to various operation conditions. Mathematical models are introduced for three-phase unbalanced power flow, voltage regulators, transformers, and loads. Furthermore, the SSR problem is formulated as a mixed-integer linear programming model, and its effectiveness is evaluated via the modified IEEE 123 node test feeder.« less
Multi-Time Step Service Restoration for Advanced Distribution Systems and Microgrids
DOE Office of Scientific and Technical Information (OSTI.GOV)
Chen, Bo; Chen, Chen; Wang, Jianhui
Modern power systems are facing increased risk of disasters that can cause extended outages. The presence of remote control switches (RCSs), distributed generators (DGs), and energy storage systems (ESS) provides both challenges and opportunities for developing post-fault service restoration methodologies. Inter-temporal constraints of DGs, ESS, and loads under cold load pickup (CLPU) conditions impose extra complexity on problem formulation and solution. In this paper, a multi-time step service restoration methodology is proposed to optimally generate a sequence of control actions for controllable switches, ESSs, and dispatchable DGs to assist the system operator with decision making. The restoration sequence is determinedmore » to minimize the unserved customers by energizing the system step by step without violating operational constraints at each time step. The proposed methodology is formulated as a mixed-integer linear programming (MILP) model and can adapt to various operation conditions. Furthermore, the proposed method is validated through several case studies that are performed on modified IEEE 13-node and IEEE 123-node test feeders.« less
ERIC Educational Resources Information Center
Rossetti, Rosemarie
Two research reports provide results of two Ohio studies to investigate factors that influence a student not to enter a high school vocational curriculum. The studies focus on the Vanguard Joint Vocational School (JVS) and five feeder comprehensive high schools and the Lawrence County JVS and seven feeder comprehensive high schools. Both reports…
Method of feeding particulate material to a fluidized bed
Borio, Richard W.; Goodstine, Stephen L.
1984-01-01
A centrifugal spreader type feeder that supplies a mixture of particulate limestone and coal to the top of a fluidized bed reactor having a flow of air upward therethrough. Large particles of particulate matter are distributed over the upper surface of the bed to utilize the natural mixing within the bed, while fine particles are adapted to utilize an independent feeder that separates them from the large particles and injects them into the bed.
DOE Office of Scientific and Technical Information (OSTI.GOV)
Nelson, Austin; Prabakar, Kumaraguru; Nagarajan, Adarsh
As more grid-connected photovoltaic (PV) inverters become compliant with evolving interconnections requirements, there is increased interest from utilities in understanding how to best deploy advanced grid-support functions (GSF) in the field. One efficient and cost-effective method to examine such deployment options is to leverage power hardware-in-the-loop (PHIL) testing methods. Two Hawaiian Electric feeder models were converted to real-time models in the OPAL-RT real-time digital testing platform, and integrated with models of GSF capable PV inverters that were modeled from characterization test data. The integrated model was subsequently used in PHIL testing to evaluate the effects of different fixed power factormore » and volt-watt control settings on voltage regulation of the selected feeders. The results of this study were provided as inputs for field deployment and technical interconnection requirements for grid-connected PV inverters on the Hawaiian Islands.« less
Eradication of Mycoplasma hyopneumoniae from a swine finishing herd without total depopulation.
Heinonen, Mari; Laurila, Tapio; Vidgren, Gabriele; Levonen, Katri
2011-04-01
Using vaccination and medication, Mycoplasma hyopneumoniae (Mhyo) was eradicated from a finishing herd without total depopulation. Altogether 3243 feeder pigs originating from Mhyo-free herds were vaccinated once using an inactivated, adjuvanted vaccine before transporting them to a Mhyo-infected finishing herd. The Mhyo-infected groups of pigs were medicated with antimicrobial agents at the time of the arrival of the first groups of Mhyo-free, vaccinated feeder pigs. The groups were operated with an all-in-all-out method in rooms with separate ventilation and slurry disposal systems. Thereafter the farmer purchased only non-vaccinated feeder pigs originating from Mhyo-free sow herds. Serology gave no positive results for 5.5 years and it was concluded that the eradication programme had been successful in producing a Mhyo-free herd without total depopulation. Copyright © 2010 Elsevier Ltd. All rights reserved.
Feederism: an exaggeration of a normative mate selection preference?
Terry, Lesley L; Suschinsky, Kelly D; Lalumière, Martin L; Vasey, Paul L
2012-02-01
Quinsey and Lalumière (1995) suggested that some, if not most, paraphilias are exaggerated manifestations of more normative and functional mate selection preferences. The present study tested whether Feederism, a fat fetish focused on erotic eating, feeding, and gaining weight, is an exaggeration of a sexual arousal pattern commonly seen in the general population. Thirty participants (15 men and 15 women) recruited from the general population were assessed using penile plethysmography and vaginal photoplethysmography, respectively. None of the participants were self-identified Feeders or Feedees. Participants were shown sexual, neutral, and feeding still images while listening to audio recordings of sexual, neutral, and feeding stories. Participants did not genitally respond to feeding stimuli. However, both men and women subjectively rated feeding stimuli as more sexually arousing than neutral stimuli. We discuss the discordance between physiological and self-reported sexual arousal in the context of sex differences in sexual concordance and implications for future research.
DOE Office of Scientific and Technical Information (OSTI.GOV)
Dall-Anese, Emiliano; Zhao, Changhong; Guggilam, Swaroop
Power networks have to withstand a variety of disturbances that affect system frequency, and the problem is compounded with the increasing integration of intermittent renewable generation. Following a large-signal generation or load disturbance, system frequency is arrested leveraging primary frequency control provided by governor action in synchronous generators. In this work, we propose a framework for distributed energy resources (DERs) deployed in distribution networks to provide (supplemental) primary frequency response. Particularly, we demonstrate how power-frequency droop slopes for individual DERs can be designed so that the distribution feeder presents a guaranteed frequency-regulation characteristic at the feeder head. Furthermore, the droopmore » slopes are engineered such that injections of individual DERs conform to a well-defined fairness objective that does not penalize them for their location on the distribution feeder. Time-domain simulations for an illustrative network composed of a combined transmission network and distribution network with frequency-responsive DERs are provided to validate the approach.« less
Hierarchical planning for a surface mounting machine placement.
Zeng, You-jiao; Ma, Deng-ze; Jin, Ye; Yan, Jun-qi
2004-11-01
For a surface mounting machine (SMM) in printed circuit board (PCB) assembly line, there are four problems, e.g. CAD data conversion, nozzle selection, feeder assignment and placement sequence determination. A hierarchical planning for them to maximize the throughput rate of an SMM is presented here. To minimize set-up time, a CAD data conversion system was first applied that could automatically generate the data for machine placement from CAD design data files. Then an effective nozzle selection approach implemented to minimize the time of nozzle changing. And then, to minimize picking time, an algorithm for feeder assignment was used to make picking multiple components simultaneously as much as possible. Finally, in order to shorten pick-and-place time, a heuristic algorithm was used to determine optimal component placement sequence according to the decided feeder positions. Experiments were conducted on a four head SMM. The experimental results were used to analyse the assembly line performance.
The Circulation Analysis of Serial Use: Numbers Game or Key to Service?
Raisig, L. Miles
1967-01-01
The conventionally erected and reported circulation analysis of serial use in the individual and the feeder library is found to be statistically invalid and misleading, since it measures neither the intellectual use of the serial's contents nor the physical handlings of serial units, and is nonrepresentative of the in-depth library use of serials. It fails utterly to report or even to suggest the relation of intralibrary and interlibrary serial resources. The actual mechanics of the serial use analysis, and the active variables in the library situation which affect serial use, are demonstrated in a simulated analysis and are explained at length. A positive design is offered for the objective gathering and reporting of data on the local intellectual use and physical handling of serials and the relating of resources. Data gathering in the feeder library, and implications for the extension of the feeder library's resources, are discussed. PMID:6055863
Miller's best/enhanced practices for flour fortification at the flour mill.
Johnson, Quentin W; Wesley, Annie S
2010-03-01
Cereal flour fortification has been identified as an effective mass fortification intervention as part of a national public health strategy to overcome micronutrient deficiencies and improve the health status of populations, especially women and children. The effectiveness of cereal flour fortification programs requires the use of micronutrient premixes that provide the desired health benefits. The Miller's Best/Enhanced Practices for Flour Fortification at the flour mill has been developed to provide specific guidance to millers and government officials to ensure that flour fortification practices are carried out in a way that results in the anticipated public health impact. The paper provides information specific to the use of micronutrient premixes, feeders, the fortification process, and quality control systems to ensure that both minimum and enhanced practices can be followed by the millers. Guidelines for basic and best/enhanced practices to be followed for each stage of the flour fortification process at the flour mill are presented. The paper is designed to be a companion to the Recommended Practices for the Production and Procurement of Premix used in Cereal Fortification Programs and supplementary to existing food quality manuals and systems, such as Good Manufacturing Practices, Food Quality Systems, and Hazard Analysis and Critical Control Points. Other stakeholders involved in flour fortification programs have the responsibility to follow best practices of their own to ensure optimum effectiveness.
Comparison of defined culture systems for feeder cell free propagation of human embryonic stem cells
Akopian, Veronika; Beil, Stephen; Benvenisty, Nissim; Brehm, Jennifer; Christie, Megan; Ford, Angela; Fox, Victoria; Gokhale, Paul J.; Healy, Lyn; Holm, Frida; Hovatta, Outi; Knowles, Barbara B.; Ludwig, Tenneille E.; McKay, Ronald D. G.; Miyazaki, Takamichi; Nakatsuji, Norio; Oh, Steve K. W.; Pera, Martin F.; Rossant, Janet; Stacey, Glyn N.; Suemori, Hirofumi
2010-01-01
There are many reports of defined culture systems for the propagation of human embryonic stem cells in the absence of feeder cell support, but no previous study has undertaken a multi-laboratory comparison of these diverse methodologies. In this study, five separate laboratories, each with experience in human embryonic stem cell culture, used a panel of ten embryonic stem cell lines (including WA09 as an index cell line common to all laboratories) to assess eight cell culture methods, with propagation in the presence of Knockout Serum Replacer, FGF-2, and mouse embryonic fibroblast feeder cell layers serving as a positive control. The cultures were assessed for up to ten passages for attachment, death, and differentiated morphology by phase contrast microscopy, for growth by serial cell counts, and for maintenance of stem cell surface marker expression by flow cytometry. Of the eight culture systems, only the control and those based on two commercial media, mTeSR1 and STEMPRO, supported maintenance of most cell lines for ten passages. Cultures grown in the remaining media failed before this point due to lack of attachment, cell death, or overt cell differentiation. Possible explanations for relative success of the commercial formulations in this study, and the lack of success with other formulations from academic groups compared to previously published results, include: the complex combination of growth factors present in the commercial preparations; improved development, manufacture, and quality control in the commercial products; differences in epigenetic adaptation to culture in vitro between different ES cell lines grown in different laboratories. PMID:20186512
Gómez, M C; Serrano, M A; Pope, C Earle; Jenkins, J A; Biancardi, M N; López, M; Dumas, C; Galiguis, J; Dresser, B L
2010-09-01
The domestic cat is a focal mammalian species that is used as a model for developing assisted reproductive technologies for preserving endangered cats and for studying human diseases. The generation of stable characterized cat embryonic stem cells (ESC) lines to use as donor nuclei may help to improve the efficiency of interspecies somatic cell nuclear transfer for preserving endangered cats and allow the creation of knockout cell lines to generate knockout cats for studying function of specific genes related to human diseases. It will also enable the possibility of producing gametes in vitro from ESC of endangered cats. In the present study, we report the generation of cat embryonic stem-like (cESL) cells from blastocysts derived entirely in vitro. We generated 32 cESL cell lines from 331 in vitro derived blastocysts from which inner cell masses were isolated by immunosurgery or by a mechanical method. Inhibition of cat dermal fibroblast (CDF) proliferation after exposure to mitomycin-C was both dose and time dependent, where doses of 30 to 40 microg/mL for 5 h were most efficient. These dosages were higher than that required to inhibit cell proliferation of mouse fetal fibroblasts (MFF; 10 microg/mL for 2.5 h). Mitomycin-C did not significantly increase necrosis of cells from either species, and had an anti-proliferative effect at concentrations below cytotoxicity. A clear species-specific relationship between feeder layers and derivation of cESL cell lines was observed, where higher numbers of cESL cell lines were generated on homologous cat feeder layers (n = 26) than from those derived on heterologous mouse feeder layers (n = 6). Three cESL cell lines generated from immunosurgery and cultured on CDF maintained self-renewal and were morphologically undifferentiated for nine and twelve passages (69-102 days). These lines showed a tightly packed dome shaped morphology, exhibited alkaline phosphatase activity and immuno-expression of the pluripotent marker OCT-4 and surface marker SSEA-1. Primary colonies at P0 to P3 and cat blastocysts expressed transcription factors OCT-4, NANOG and SOX-2 and the proto-oncogene C-MYC. However, expression was at levels significantly lower than in vitro produced blastocysts. During culture, cESL colonies spontaneously differentiated into fibroblasts, cardiomyocytes, and embryoid bodies. Development of techniques to prevent differentiation of cESL cells will be essential for maintaining defined cell lines. Copyright 2010 Elsevier Inc. All rights reserved.
Rainbow trout can discriminate between feeds with different oil sources.
Geurden, I; Cuvier, A; Gondouin, E; Olsen, R E; Ruohonen, K; Kaushik, S; Boujard, T
2005-06-02
The purpose of present two-choice trials was to examine the capacity of groups of juvenile rainbow trout to differentiate between two isolipidic diets containing distinct oils and to detect an eventual preference. The choice was offered by means of two self-feeders per tank. One feeder distributed a standard diet with fish oil (FO), the other a diet containing vegetable oil, either rich in linolenic acid (linseed oil, LO), linoleic acid (sunflower oil, SO), or oleic acid (rapeseed oil, RO). Each 15-day preference test was preceded by a 15-day adaptation period during which both feeders distributed the same diet. The tests were followed by a 10- to 15-day validation period in order to confirm that feeder solicitations were steered by the characteristics of the diets. Preferences were expressed as relative changes in feed demands for a specific feeder. Averaged over all groups, the preference tests demonstrated the capacity of rainbow trout to discriminate between a diet with FO and a diet containing vegetable oil, and indicated a general preference for the diet with FO over the other diets irrespective of whether they received the diet with fish oil (Experiment 1) or with vegetable oil (Experiment 2) prior to the preference test. The tests also indicated a difference in the extent of relative avoidance of each of the three vegetable oil diets. Diet LO was the most avoided, as indicated by the 37-39% decrease in demands for the feeder with diet LO (P<0.05). Diet RO was the best accepted, causing a decrease in feed demands of only 15-17% (P>0.05). The avoidance of diet SO at the end of the preference test was 30% (P>0.05) after an initially higher avoidance of 43% (P<0.05). It is believed that the metabolic consequences of the excess of linolenic or linoleic acid negatively affected the feed acceptances of diets LO and SO. Further work is needed to elucidate a possible interference of differences in palatability. In all groups, the lower demands for the vegetable oil diets were compensated by increased demands for diet FO. Hence, changes in diet selection had no effect on total feed or energy intakes, measured as the sum of both selections.
Vibratory high pressure coal feeder having a helical ramp
Farber, Gerald
1978-01-01
Apparatus and method for feeding powdered coal from a helical ramp into a high pressure, heated, reactor tube containing hydrogen for hydrogenating the coal and/or for producing useful products from coal. To this end, the helical ramp is vibrated to feed the coal cleanly at an accurately controlled rate in a simple reliable and trouble-free manner that eliminates complicated and expensive screw feeders, and/or complicated and expensive seals, bearings and fully rotating parts.
Blinov, N N
2000-01-01
Specifications for the main element of a modern X-ray diagnostic device an X-ray feeder are formulated. There is evidence for choosing its parameters. The new rational routine of X-ray study and the layout of a X-ray room are proposed. Information on the up-to-date commercially manufactured basic medium-frequency general-purpose X-ray feeder "URP-30 SCh Amico" is given.
A suspension-feeding anomalocarid from the Early Cambrian.
Vinther, Jakob; Stein, Martin; Longrich, Nicholas R; Harper, David A T
2014-03-27
Large, actively swimming suspension feeders evolved several times in Earth's history, arising independently from groups as diverse as sharks, rays and stem teleost fishes, and in mysticete whales. However, animals occupying this niche have not been identified from the early Palaeozoic era. Anomalocarids, a group of stem arthropods that were the largest nektonic animals of the Cambrian and Ordovician periods, are generally thought to have been apex predators. Here we describe new material from Tamisiocaris borealis, an anomalocarid from the Early Cambrian (Series 2) Sirius Passet Fauna of North Greenland, and propose that its frontal appendage is specialized for suspension feeding. The appendage bears long, slender and equally spaced ventral spines furnished with dense rows of long and fine auxiliary spines. This suggests that T. borealis was a microphagous suspension feeder, using its appendages for sweep-net capture of food items down to 0.5 mm, within the size range of mesozooplankton such as copepods. Our observations demonstrate that large, nektonic suspension feeders first evolved during the Cambrian explosion, as part of an adaptive radiation of anomalocarids. The presence of nektonic suspension feeders in the Early Cambrian, together with evidence for a diverse pelagic community containing phytoplankton and mesozooplankton, indicate the existence of a complex pelagic ecosystem supported by high primary productivity and nutrient flux. Cambrian pelagic ecosystems seem to have been more modern than previously believed.
Soteriou, Despina; Iskender, Banu; Byron, Adam; Humphries, Jonathan D.; Borg-Bartolo, Simon; Haddock, Marie-Claire; Baxter, Melissa A.; Knight, David; Humphries, Martin J.; Kimber, Susan J.
2013-01-01
Human embryonic stem cells (hESCs) are pluripotent cells that have indefinite replicative potential and the ability to differentiate into derivatives of all three germ layers. hESCs are conventionally grown on mitotically inactivated mouse embryonic fibroblasts (MEFs) or feeder cells of human origin. In addition, feeder-free culture systems can be used to support hESCs, in which the adhesive substrate plays a key role in the regulation of stem cell self-renewal or differentiation. Extracellular matrix (ECM) components define the microenvironment of the niche for many types of stem cells, but their role in the maintenance of hESCs remains poorly understood. We used a proteomic approach to characterize in detail the composition and interaction networks of ECMs that support the growth of self-renewing hESCs. Whereas many ECM components were produced by supportive and unsupportive MEF and human placental stromal fibroblast feeder cells, some proteins were only expressed in supportive ECM, suggestive of a role in the maintenance of pluripotency. We show that identified candidate molecules can support attachment and self-renewal of hESCs alone (fibrillin-1) or in combination with fibronectin (perlecan, fibulin-2), in the absence of feeder cells. Together, these data highlight the importance of specific ECM interactions in the regulation of hESC phenotype and provide a resource for future studies of hESC self-renewal. PMID:23658023
NASA Astrophysics Data System (ADS)
Rossi, Sergio; Snyder, Mark J.; Gili, Josep-Marìa
2006-03-01
In the present paper we suggest an effect of seasonal variations in food availability on two ecophysiological parameters in a warm temperate benthic suspension feeder: the tissue concentrations of proteins, carbohydrates and lipids on the one hand, and the expression of stress proteins (HSP 70 and 90, inducible and/or constitutive) on the other hand. The concentrations of biomacromolecules have already been used to describe bentho-pelagic and reproductive processes, but this is the first time that stress protein expression is suggested to be directly related with food constraints in marine organisms. Paramuricea clavata (Cnidaria: Gorgonacea) express HSP 70 and 90 (constitutive and/or inducible) throughout the seasonal cycle, and HSP 70 levels are twice as high as the levels of HSP 90. In summer and autumn, when seston availability to suspension feeders was low, P. clavata showed low levels of carbohydrates and lipids, but high levels of HSPs expression. The levels of HSP 70 and 90 expression fit with negative exponential functions of carbohydrate and lipid concentrations. We suggest a direct effect of food availability on the studied ecophysiological parameters while the effect of temperature may be rather indirect. HSP expression as well as the tissue concentrations of carbohydrate and lipids may be used as biomarkers of environmental changes and seston availability to benthic suspension feeders.
NASA Astrophysics Data System (ADS)
Patel, R.; Panchal, P.; Panchal, R.; Tank, J.; Mahesuriya, G.; Sonara, D.; Srikanth, G. L. N.; Garg, A.; Bairagi, N.; Christian, D.; Patel, K.; Shah, P.; Nimavat, H.; Sharma, R.; Patel, J. C.; Gupta, N. C.; Prasad, U.; Sharma, A. N.; Tanna, V. L.; Pradhan, S.
The SST-1 machine comprises a superconducting magnet system (SCMS), which includes TF and PF magnets. In order to charge the SCMS, we need superconducting current feeders consisting of SC feeders and vapor cooled current leads (VCCLs). We have installed all 10 (+/-) pairs of VCCLs for the TF and PF systems. While conducting initial engineering validation of the SST-1 machine, our prime objective was to produce circular plasma using only the TF system. During the SST-1 campaign I to VI, we have to stop the PF magnets cooling in order to get the cryo- stable conditions for current charging of the TF magnets system. In that case, the cooling of the PF current leads is not essential. It has been also observed that after aborting the PF system cooling, there was a limited experimental window of TF operation. Therefore, in the recent SST-1 campaign-VII, we removed the PF current leads (9 pairs) and kept only single (+/-) pair of the 10,000 A rated VCCLs to realize the charging of the TF system for the extended window of operation. We have observed a better cryogenic stability in the TF magnets after modifications in the CFS. In this paper, we report the comparison of the cool down performance for the SST-1 machine operation before and after modifications of the current feeders system.
Exploring Opportunities for Efficiency and Joint Provision of Services Using Nonappropriated Funds
2016-01-01
analyzed two of them: accounting and employee benefits. RAND assessed the rec- ommendations’ costs , detailed the potential challenges, and identified...Consolidated Service Center: This option would standardize all accounting , including the SGL, cost - center structures, and core feeder and financial...ings of about $100 million would go toward replacing its out- dated accounting system. The analysis considered the costs of developing, deploying
Lee, Myungook; Ahn, Jong Il; Ahn, Ji Yeon; Yang, Woo Sub; Hubbell, Jeffrey A; Lim, Jeong Mook; Lee, Seung Tae
2017-11-01
We evaluated whether the genetic background of embryonic stem cells (ESCs) affects the properties suitable for three-dimensional (3D) synthetic scaffolds for cell self-renewal. Inbred R1 and hybrid B6D2F1 mouse ESC lines were cultured for 7 days in hydrogel scaffolds with different properties derived from conjugating 7.5, 10, 12.5, or 15% (wt/vol) vinylsulfone-functionalized three-, four-, or eight-arm polyethylene glycol (PEG) with dicysteine-containing crosslinkers with an intervening matrix metalloproteinase-specific cleavage sites. Cell proliferation and expression of self-renewal-related genes and proteins by ESCs cultured in feeder-free or containing 2D culture plate or 3D hydrogel were monitored. As a preliminary experiment, the E14 ESC-customized synthetic 3D microenvironment did not maintain self-renewal of either the R1 or B6D2F1 ESCs. The best R1 cell proliferation (10.04 vs. 0.16-4.39; p < 0.0001) was observed in the four-arm 7.5% PEG-based hydrogels than those with other properties, whereas the F1 ESCs showed better proliferation when they were embedded in the three-arm 10% hydrogels. Self-renewal-related gene and protein expression by ESCs after feeder-free 3D culture was generally maintained compared with the feeder-containing 2D culture, but expression patterns and quantities differed. However, the feeder-free 3D culture yielded better expression than the feeder-free 2D culture. In conclusion, genetic background determined the suitability of hydrogel scaffolds for self-renewal of ESCs, which requires customization for the mechanical properties of each cell line. © 2016 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater, 105B: 2261-2268, 2017. © 2016 Wiley Periodicals, Inc.
Circadian feeding patterns of 12-month-old infants.
Wee, Poh Hui; Loy, See Ling; Toh, Jia Ying; Tham, Elaine Kwang Hsia; Cheung, Yin Bun; Godfrey, Keith M; Gluckman, Peter D; Saw, Seang Mei; Chong, Yap-Seng; Lek, Ngee; Chan, Jerry Kok Yen; Goh, Daniel Yam Thiam; Chong, Mary Foong-Fong; Yap, Fabian
2017-06-01
Early life nutrition and feeding practices are important modifiable determinants of subsequent obesity, yet little is known about the circadian feeding pattern of 12-month-old infants. We aimed to describe the 24-h feeding patterns of 12-month-old infants and examine their associations with maternal and infant characteristics. Mothers from a prospective birth cohort study (n 431) reported dietary intakes of their 12-month-old infants and respective feeding times using 24-h dietary recall. Based on their feeding times, infants were classified into post-midnight (00.00-05.59 hours) and pre-midnight (06.00-23.59 hours) feeders. Mean daily energy intake was 3234 (sd 950) kJ (773 (sd 227) kcal), comprising 51·8 (sd 7·8) % carbohydrate, 33·9 (sd 7·2) % fat and 14·4 (sd 3·2) % protein. Mean hourly energy intake and proportion of infants fed were lower during post-midnight than pre-midnight hours. There were 251 (58·2 %) pre-midnight and 180 (41·8 %) post-midnight feeders. Post-midnight feeders consumed higher daily energy, carbohydrate, fat and protein intakes than pre-midnight feeders (all P<0·001). The difference in energy intake originated from energy content consumed during the post-midnight period. Majority (n 173) of post-midnight feeders consumed formula milk during the post-midnight period. Using multivariate logistic regression with confounder adjustment, exclusively breast-feeding during the first 6 months of life was negatively associated with post-midnight feeding at 12 months (adjusted OR 0·31; 95 % CI 0·11, 0·82). This study provides new insights into the circadian pattern of energy intake during infancy. Our findings indicated that the timing of feeding at 12 months was associated with daily energy and macronutrient intakes, and feeding mode during early infancy.
Rapid fibroblast removal from high density human embryonic stem cell cultures.
Turner, William S; McCloskey, Kara E
2012-10-28
Mouse embryonic fibroblasts (MEFs) were used to establish human embryonic stem cells (hESCs) cultures after blastocyst isolation(1). This feeder system maintains hESCs from undergoing spontaneous differentiation during cell expansion. However, this co-culture method is labor intensive, requires highly trained personnel, and yields low hESC purity(4). Many laboratories have attempted to minimize the number of feeder cells in hESC cultures (i.e. incorporating matrix-coated dishes or other feeder cell types(5-8)). These modified culture systems have shown some promise, but have not supplanted the standard method for culturing hESCs with mitomycin C-treated mouse embyronic fibroblasts in order to retard unwanted spontaneous differentiation of the hESC cultures. Therefore, the feeder cells used in hESC expansion should be removed during differentiation experiments. Although several techniques are available for purifying the hESC colonies (FACS, MACS, or use of drug resistant vectors) from feeders, these techniques are labor intensive, costly and/or destructive to the hESC. The aim of this project was to invent a method of purification that enables the harvesting of a purer population of hESCs. We have observed that in a confluent hESC culture, the MEF population can be removed using a simple and rapid aspiration of the MEF sheet. This removal is dependent on several factors, including lateral cell-to-cell binding of MEFs that have a lower binding affinity to the styrene culture dish, and the ability of the stem cell colonies to push the fibroblasts outward during the generation of their own "niche". The hESC were then examined for SSEA-4, Oct3/4 and Tra 1-81 expression up to 10 days after MEF removal to ensure maintenance of pluripotency. Moreover, hESC colonies were able to continue growing from into larger formations after MEF removal, providing an additional level of hESC expansion.
Oubari, Farhad; Amirizade, Naser; Mohammadpour, Hemn; Nakhlestani, Mozhdeh; Zarif, Mahin Nikougoftar
2015-01-01
Hematopoietic stem cells (HSCs) transplantation using umbilical cord blood (UCB) has improved during the last decade. Because of cell limitations, several studies focused on the ex vivo expansion of HSCs. Numerous investigations were performed to introduce the best cytokine cocktails for HSC expansion The majority used the Fms-related tyrosine kinase 3 ligand (FLT3-L) as a critical component. According to FLT3-L biology, in this study we have investigated the hypothesis that FLT3-L only effectively induces HSCs expansion in the presence of a mesenchymal stem cell (MSC) feeder. In this experimental study, HSCs and MSCs were isolated from UCB and placenta, respectively. HSCs were cultured in different culture conditions in the presence and absence of MSC feeder and cytokines. After ten days of culture, total nucleated cell count (TNC), cluster of differentiation 34+(CD34(+)) cell count, colony forming unit assay (CFU), long-term culture initiating cell (LTC-IC), homeobox protein B4 (HoxB4) mRNA and surface CD49d expression were evaluated. The fold increase for some culture conditions was compared by the t test. HSCs expanded in the presence of cytokines and MSCs feeder. The rate of expansion in the co-culture condition was two-fold more than culture with cytokines (P<0.05). FLT3-L could expand HSCs in the co-culture condition at a level of 20-fold equal to the presence of stem cell factor (SCF), thrombopoietin (TPO) and FLT3-L without feeder cells. The number of extracted colonies from LTC-IC and CD49d expression compared with a cytokine cocktail condition meaningfully increased (P<0.05). FLT3-L co-culture with MSCs can induce high yield expansion of HSCs and be a substitute for the universal cocktail of SCF, TPO and FLT3-L in feeder-free culture.
Absence of Suction Feeding Ichthyosaurs and Its Implications for Triassic Mesopelagic Paleoecology
Motani, Ryosuke; Ji, Cheng; Tomita, Taketeru; Kelley, Neil; Maxwell, Erin; Jiang, Da-yong; Sander, Paul Martin
2013-01-01
Mesozoic marine reptiles and modern marine mammals are often considered ecological analogs, but the extent of their similarity is largely unknown. Particularly important is the presence/absence of deep-diving suction feeders among Mesozoic marine reptiles because this would indicate the establishment of mesopelagic cephalopod and fish communities in the Mesozoic. A recent study suggested that diverse suction feeders, resembling the extant beaked whales, evolved among ichthyosaurs in the Triassic. However, this hypothesis has not been tested quantitatively. We examined four osteological features of jawed vertebrates that are closely linked to the mechanism of suction feeding, namely hyoid corpus ossification/calcification, hyobranchial apparatus robustness, mandibular bluntness, and mandibular pressure concentration index. Measurements were taken from 18 species of Triassic and Early Jurassic ichthyosaurs, including the presumed suction feeders. Statistical comparisons with extant sharks and marine mammals of known diets suggest that ichthyosaurian hyobranchial bones are significantly more slender than in suction-feeding sharks or cetaceans but similar to those of ram-feeding sharks. Most importantly, an ossified hyoid corpus to which hyoid retractor muscles attach is unknown in all but one ichthyosaur, whereas a strong integration of the ossified corpus and cornua of the hyobranchial apparatus has been identified in the literature as an important feature of suction feeders. Also, ichthyosaurian mandibles do not narrow rapidly to allow high suction pressure concentration within the oral cavity, unlike in beaked whales or sperm whales. In conclusion, it is most likely that Triassic and Early Jurassic ichthyosaurs were ‘ram-feeders’, without any beaked-whale-like suction feeder among them. When combined with the inferred inability for dim-light vision in relevant Triassic ichthyosaurs, the fossil record of ichthyosaurs does not suggest the establishment of modern-style mesopelagic animal communities in the Triassic. This new interpretation matches the fossil record of coleoids, which indicates the absence of soft-bodied deepwater species in the Triassic. PMID:24348983
12. VIEW OF WESTERN CANAL AT ALMA SCHOOL ROAD IN ...
12. VIEW OF WESTERN CANAL AT ALMA SCHOOL ROAD IN MESA, THE LOCATION AT WHICH THE PECK, PINE AND WALLACE FEEDERS FORMERLY JOINED TO FORM THE WESTERN CANAL. THE PECK AND PINE FEEDERS, NOW KNOWN AS LATERAL 9 AND LATERAL 10, AND ALMOST ENTIRELY PIPED, STILL JOIN THE WESTERN CANAL AT THIS POINT, BUT AN EQUALLY IMPORTANT SOURCE OF SUPPLY IS THE NUMEROUS GROUNDWATER PUMPS LOCATED ON THE SYSTEM. - Western Canal, South side of Salt River between Tempe, Phoenix & Mesa, Mesa, Maricopa County, AZ
Design and Scheduling of Microgrids using Benders Decomposition
DOE Office of Scientific and Technical Information (OSTI.GOV)
Nagarajan, Adarsh; Ayyanar, Raja
2016-11-21
The distribution feeder laterals in a distribution feeder with relatively high PV generation as compared to the load can be operated as microgrids to achieve reliability, power quality and economic benefits. However, renewable resources are intermittent and stochastic in nature. A novel approach for sizing and scheduling an energy storage system and microturbine for reliable operation of microgrids is proposed. The size and schedule of an energy storage system and microturbine are determined using Benders' decomposition, considering PV generation as a stochastic resource.
Jiang, Zhiwu; Wu, Di; Ye, Wei; Weng, Jianyu; Lai, Peilong; Shi, Pengcheng; Guo, Xutao; Huang, Guohua; Deng, Qiuhua; Tang, Yanlai; Zhao, Hongyu; Cui, Shuzhong; Lin, Simiao; Wang, Suna; Li, Baiheng; Wu, Qiting; Li, Yangqiu; Liu, Pentao; Pei, Duanqing; Du, Xin; Yao, Yao; Li, Peng
2017-12-05
Functional screening for compounds represents a major hurdle in the development of rational therapeutics for B-acute lymphoblastic leukemia (B-ALL). In addition, using cell lines as valid models for evaluating responses to novel drug therapies raises serious concerns, as cell lines are prone to genotypic/phenotypic drift and loss of heterogeneity in vitro . Here, we reported that OP9 cells, not OP9-derived adipocytes (OP9TA), support the growth of primary B-ALL cells in vitro . To identify the factors from OP9 cells that support the growth of primary B-ALL cells, we performed RNA-Seq to analyze the gene expression profiles of OP9 and OP9TA cells. We thus developed a defined, serum/feeder-free condition (FI76V) that can support the expansion of a range of clinically distinct primary B-ALL cells that still maintain their leukemia-initiating ability. We demonstrated the suitability of high-throughput drug screening based on our B-ALL cultured conditions. Upon screening 378 kinase inhibitors, we identified a cluster of 17 kinase inhibitors that can efficiently kill B-ALL cells in vitro . Importantly, we demonstrated the synergistic cytotoxicity of dinaciclib/BTG226 to B-ALL cells. Taken together, we developed a defined condition for the ex vivo expansion of primary B-ALL cells that is suitable for high-throughput screening of novel compounds.
Firth, Josh A; Sheldon, Ben C; Farine, Damien R
2016-06-01
Animals regularly use information from others to shape their decisions. Yet, determining how changes in social structure affect information flow and social learning strategies has remained challenging. We manipulated the social structure of a large community of wild songbirds by controlling which individuals could feed together at automated feeding stations (selective feeders). We then provided novel ephemeral food patches freely accessible to all birds and recorded the spread of this new information. We demonstrate that the discovery of new food patches followed the experimentally imposed social structure and that birds disproportionately learnt from those whom they could forage with at the selective feeders. The selective feeders reduced the number of conspecific information sources available and birds subsequently increased their use of information provided by heterospecifics. Our study demonstrates that changes to social systems carry over into pathways of information transfer and that individuals learn from tutors that provide relevant information in other contexts. © 2016 The Authors.
Primary Frequency Response with Aggregated DERs: Preprint
DOE Office of Scientific and Technical Information (OSTI.GOV)
Guggilam, Swaroop S.; Dhople, Sairaj V.; Zhao, Changhong
2017-03-03
Power networks have to withstand a variety of disturbances that affect system frequency, and the problem is compounded with the increasing integration of intermittent renewable generation. Following a large-signal generation or load disturbance, system frequency is arrested leveraging primary frequency control provided by governor action in synchronous generators. In this work, we propose a framework for distributed energy resources (DERs) deployed in distribution networks to provide (supplemental) primary frequency response. Particularly, we demonstrate how power-frequency droop slopes for individual DERs can be designed so that the distribution feeder presents a guaranteed frequency-regulation characteristic at the feeder head. Furthermore, the droopmore » slopes are engineered such that injections of individual DERs conform to a well-defined fairness objective that does not penalize them for their location on the distribution feeder. Time-domain simulations for an illustrative network composed of a combined transmission network and distribution network with frequency-responsive DERs are provided to validate the approach.« less
Hydrodynamic control of phytoplankton loss to the benthos in an estuarine environment
Jones, Nicole L.; Thompson, Janet K.; Arrigo, Kevin R.; Monismith, Stephen G.
2009-01-01
Field experiments were undertaken to measure the influence of hydrodynamics on the removal of phytoplankton by benthic grazers in Suisun Slough, North San Francisco Bay. Chlorophyll a concentration boundary layers were found over beds inhabited by the active suspension feeders Corbula amurensis and Corophium alienense and the passive suspension feeders Marenzellaria viridis and Laonome sp. Benthic losses of phytoplankton were estimated via both the control volume and the vertical flux approach, in which chlorophyll a concentration was used as a proxy for phytoplankton biomass. The rate of phytoplankton loss to the bed was positively correlated to the bed shear stress. The maximum rate of phytoplankton loss to the bed was five times larger than estimated by laboratory-derived pumping rates for the active suspension feeders. Reasons for this discrepancy are explored including a physical mechanism whereby phytoplankton is entrained in a near-bed fluff layer where aggregation is mediated by the presence of mucus produced by the infaunal community.
Hydrodynamic control of phytoplankton loss to the benthos in an estuarine environment
Jones, N.L.; Thompson, J.K.; Arrigo, K.R.; Monismith, Stephen G.
2009-01-01
Field experiments were undertaken to measure the influence of hydrodynamics on the removal of phytoplankton by benthic grazers in Suisun Slough, North San Francisco Bay. Chlorophyll a concentration boundary layers were found over beds inhabited by the active suspension feeders Corbula amurensis and Corophium alienense and the passive suspension feeders Marenzellaria viridis and Laonome sp. Benthic losses of phytoplankton were estimated via both the control volume and the vertical flux approach, in which chlorophyll a concentration was used as a proxy for phytoplankton biomass. The rate of phytoplankton loss to the bed was positively correlated to the bed shear stress. The maximum rate of phytoplankton loss to the bed was five times larger than estimated by laboratory-derived pumping rates for the active suspension feeders. Reasons for this discrepancy are explored including a physical mechanism whereby phytoplankton is entrained in a near-bed fluff layer where aggregation is mediated by the presence of mucus produced by the infaunal community. ?? 2009, by the American Society of Limnology and Oceanography, Inc.
The effects of automated scatter feeders on captive grizzly bear activity budgets.
Andrews, Nathan L P; Ha, James C
2014-01-01
Although captive bears are popular zoo attractions, they are known to exhibit high levels of repetitive behaviors (RBs). These behaviors have also made them particularly popular subjects for welfare research. To date, most research on ursid welfare has focused on various feeding methods that seek to increase time spent searching for, extracting, or consuming food. Prior research indicates an average of a 50% reduction in RBs when attempts are successful and, roughly, a 50% success rate across studies. This research focused on decreasing time spent in an RB while increasing the time spent active by increasing time spent searching for, extracting, and consuming food. The utility of timed, automated scatter feeders was examined for use with captive grizzly bears (Ursis arctos horribilis). Findings include a significant decrease in time spent in RB and a significant increase in time spent active while the feeders were in use. Further, the bears exhibited a wider range of behaviors and a greater use of their enclosure.
Liu, Te; Cheng, Weiwei; Liu, Tianjin; Guo, Lihe; Huang, Qin; Jiang, Lizhen; Du, Xiling; Xu, Fuhui; Liu, Zhixue; Lai, Dongmei
2010-02-01
Mouse embryonic stem cells (ESCs) are typically cultured on a feeder layer of mouse embryonic fibroblasts (MEFs), with leukemia inhibitory factor (LIF) added to maintain them in an undifferentiated state. We have previously shown that human amniotic epithelial cells (hAECs) can be used as feeder cells to maintain mouse ESC pluripotency, but the mechanism for this is unknown. In the present study, we found that CpG islands 5' of the c-Myc gene remain hypomethylated in mouse ESCs cultured on hAECs. In addition, levels of acetylation of histone H3 and trimethylation of histone H3K4 in the c-Myc gene promoter were higher in ES cells cultured on hAECs than those in ES cells cultured on MEFs. These data suggested that hAECs can alter mouse ESC gene expression via epigenetic modification of c-Myc, providing a possible mechanism for the hAEC-induced maintenance of ESCs in an undifferentiated state.
Properties of murine embryonic stem cells maintained on human foreskin fibroblasts without LIF.
Meng, G L; Zur Nieden, N I; Liu, S Y; Cormier, J T; Kallos, M S; Rancourt, D E
2008-04-01
In embryonic stem (ES) cells, leukemia inhibitory factor (LIF)/STAT3, wnt and nodal/activin signaling are mainly active to control pluripotency during expansion. To maintain pluripotency, ES cells are typically cultured on feeder cells of varying origins. Murine ES cells are commonly cultured on murine embryonic fibroblasts (MEFs), which senesce early and must be frequently prepared. This process is laborious and leads to batch variation presenting a challenge for high-throughput ES cell expansion. Although some cell lines can be sustained by exogenous LIF, this method is costly. We present here a novel and inexpensive culture method for expanding murine ES cells on human foreskin fibroblast (HFF) feeders. After 20 passages on HFFs without LIF, ES cell lines showed normal expression levels of pluripotency markers, maintained a normal karyotype and retained the ability to contribute to the germline. As HFFs do not senesce for at least 62 passages, they present a vast supply of feeders. Copyright 2007 Wiley-Liss, Inc.
Structure and seasonality in a Malaysian mudflat community
NASA Astrophysics Data System (ADS)
Broom, M. J.
1982-08-01
An assessment of community composition and the functional roles of the dominant species has been carried out in two intertidal areas of Malaysian mudflat dominated by natural populations of the arcid bivalve mollusc Anadara granosa. In addition to A. granosa, organisms of numerical importance are the venerid bivalve Pelecyora trigona, the neogastropod Plicarcularia leptospira, the mesogastropods Stenothyra glabrata and Cerithidea cingulata and the hermit crab Diogenes sp. The mesogastropod Natica maculosa and the neogastropod Thais carinifera may be of some importance to community organization but they are not numerically dominant. Annelids are conspicuous by their absence. The following trophic roles are ascribed to specific members of the community: A. granosa—facultative surface deposit feeder; P. trigona—suspension feeder; P. leptospira—scavenger; C. cingulata—deposit feeder/grazer; S. glabrata—deposit feeder/grazer; N. maculosa—predator; T. carinifera—predator; Diogenes sp.—scavenger/predator. S. glabrata is of particular interest because it appears to fill the niche occupied by mud snails of the genus Hydrobia in temperate mudflat systems. There is evidence of seasonality on the mudflats which points to a spawning of certain forms triggered by the major annual salinity depression at the time of the onset of the north-east monsoon in October/November. Concentrations of benthic chlorophyll a show no obvious signs of a seasonal fluctuation and the seasonality of the primary consumers is not thought to be related to food abundance. However there is some evidence of seasonality of reproduction in N. maculosa which preys on the seasonally reproducing bivalves.
Singh, A S; Shah, A; Brockmann, A
2018-02-01
In honey bees, continuous foraging at an artificial feeder induced a sustained upregulation of the immediate early genes early growth response protein 1 (Egr-1) and hormone receptor 38 (Hr38). This gene expression response was accompanied by an upregulation of several Egr-1 candidate downstream genes: ecdysone receptor (EcR), dopamine/ecdysteroid receptor (DopEcR), dopamine decarboxylase and dopamine receptor 2. Hr38, EcR and DopEcR are components of the ecdysteroid signalling pathway, which is highly probably involved in learning and memory processes in honey bees and other insects. Time-trained foragers still showed an upregulation of Egr-1 when the feeder was presented at an earlier time of the day, suggesting that the genomic response is more dependent on the food reward than training time. However, presentation of the feeder at the training time without food was still capable of inducing a transient increase in Egr-1 expression. Thus, learnt feeder cues, or even training time, probably affect Egr-1 expression. In contrast, whole brain Egr-1 expression changes did not differ between dancing and nondancing foragers. On the basis of our results we propose that food reward induced continuous foraging ultimately elicits a genomic response involving Egr-1 and Hr38 and their downstream genes. Furthermore this genomic response is highly probably involved in foraging-related learning and memory responses. © 2017 The Royal Entomological Society.
Host Shifts from Lamiales to Brassicaceae in the Sawfly Genus Athalia
Opitz, Sebastian E. W.; Boevé, Jean-Luc; Nagy, Zoltán Tamás; Sonet, Gontran; Koch, Frank; Müller, Caroline
2012-01-01
Plant chemistry can be a key driver of host shifts in herbivores. Several species in the sawfly genus Athalia are important economic pests on Brassicaceae, whereas other Athalia species are specialized on Lamiales. These host plants have glucosides in common, which are sequestered by larvae. To disentangle the possible direction of host shifts in this genus, we examined the sequestration specificity and feeding deterrence of iridoid glucosides (IGs) and glucosinolates (GSs) in larvae of five species which either naturally sequester IGs from their hosts within the Plantaginaceae (Lamiales) or GSs from Brassicaceae, respectively. Furthermore, adults were tested for feeding stimulation by a neo-clerodane diterpenoid which occurs in Lamiales. Larvae of the Plantaginaceae-feeders did not sequester artificially administered p-hydroxybenzylGS and were more deterred by GSs than Brassicaceae-feeders were by IGs. In contrast, larvae of Brassicaceae-feeders were able to sequester artificially administered catalpol (IG), which points to an ancestral association with Lamiales. In line with this finding, adults of all tested species were stimulated by the neo-clerodane diterpenoid. Finally, in a phylogenetic tree inferred from genetic marker sequences of 21 Athalia species, the sister species of all remaining 20 Athalia species also turned out to be a Lamiales-feeder. Fundamental physiological pre-adaptations, such as the establishment of a glucoside transporter, and mechanisms to circumvent activation of glucosides by glucosidases are therefore necessary prerequisites for successful host shifts between Lamiales and Brassicaceae. PMID:22485146
Resolving the architecture of monogenetic feeder systems from exposures of extinct volcanic fields
NASA Astrophysics Data System (ADS)
Muirhead, J.; Van Eaton, A. R.; Re, G.; White, J. D. L.; Ort, M. H.
2016-12-01
Monogenetic volcanic fields pose hazards to a number of major cities worldwide. During an eruption, the evolution of the intrusive feeder network modulates eruption behavior and location, as well as the warning signs of impending activity. However, historical examples of monogenetic eruptions are rare, particularly those monitored with the modern tools required to constrain the geometry and interconnectivity of subsurface intrusive feeders (e.g., InSAR, GPS). Geologic exposures in extinct fields around the Colorado Plateau provide clues to the geometry of shallow intrusions (<1000 m depth) that feed monogenetic volcanoes. We present field- and satellite-based observations of exposed intrusions in the Hopi Buttes volcanic field (Arizona), which reveal that many eruptions were fed by interconnected dike-sill systems. Results from the Hopi Buttes show that volcanic cone alignment studies are biased to the identification of dike intrusions, and thereby neglect the important contributions of sills to shallow feeder systems. For example, estimates of intruded volumes in fields exhumed by uplift and erosion in Utah and Arizona show that sills make up 30 - 92% of the shallow intruded volume within 1000 m of the paleosurface. By transporting magma toward and away from eruptive conduits, these sills likely played a role in modulating eruption styles (e.g., explosive vs effusive) and controlling lateral vent migrations. Sill transitions at Hopi Buttes would have produced detectable surface uplifts, and illustrate the importance of geological studies for informing interpretations of geodetic and seismological data during volcanic crises.
Nel, Holly A; Dalu, Tatenda; Wasserman, Ryan J
2018-01-15
Microplastics are important novel pollutants in freshwaters but their behaviour in river sediments is poorly understood due to the large amounts of coloured dissolved organic matter that impede sample processing. The present study aimed to 1.) estimate the microplastic pollution dynamics in an urban river system experiencing temporal differences in river flow, and 2.) investigate the potential use of chironomids as indicators of microplastic pollution levels in degraded freshwater environments. Microplastic levels were estimated from sediment and Chironomus spp. larvae collected from various sites along the Bloukrans River system, in the Eastern Cape South Africa during the summer and winter season. River flow, water depth, channel width, substrate embeddedness and sediment organic matter were simultaneously collected from each site. The winter season was characterised by elevated microplastic abundances, likely as a result of lower energy and increased sediment deposition associated with reduced river flow. In addition, results showed that particle distribution may be governed by various other external factors, such as substrate type and sediment organic matter. The study further highlighted that deposit feeders associated with the benthic river habitats, namely Chironomus spp. ingest microplastics and that the seasonal differences in sediment microplastic dynamics were reflected in chironomid microplastic abundance. There was a positive, though weakly significant relationship between deposit feeders and sediment suggesting that deposit feeders such as Chironomus spp. larvae could serve as an important indicator of microplastic loads within freshwater ecosystems. Copyright © 2017 Elsevier B.V. All rights reserved.
NASA Astrophysics Data System (ADS)
Yang, Xue; Wang, Hongbo; Sun, Li; Yu, Hongnian
2015-03-01
To develop a robot system for minimally invasive surgery is significant, however the existing minimally invasive surgery robots are not applicable in practical operations, due to their limited functioning and weaker perception. A novel wire feeder is proposed for minimally invasive vascular interventional surgery. It is used for assisting surgeons in delivering a guide wire, balloon and stenting into a specific lesion location. By contrasting those existing wire feeders, the motion methods for delivering and rotating the guide wire in blood vessel are described, and their mechanical realization is presented. A new resistant force detecting method is given in details. The change of the resistance force can help the operator feel the block or embolism existing in front of the guide wire. The driving torque for rotating the guide wire is developed at different positions. Using the CT reconstruction image and extracted vessel paths, the path equation of the blood vessel is obtained. Combining the shapes of the guide wire outside the blood vessel, the whole bending equation of the guide wire is obtained. That is a risk criterion in the delivering process. This process can make operations safer and man-machine interaction more reliable. A novel surgery robot for feeding guide wire is designed, and a risk criterion for the system is given.
Brenes-Soto, Andrea; Dierenfeld, Ellen S
2014-01-01
Several species in captivity develop nutritional diseases including vitamin A deficiency; cases of this disease have been documented in amphibians, which may be linked to an insectivorous diet lacking in vitamin A or carotenoids. Adults and young of Dyscophus guineti were fed three diets over 9 weeks to evaluate effects on carotenoids and vitamin A status and skin pigmentation. Feeder crickets were either supplemented with soy oil (control, CON), soy oil enriched with β-carotene (BC) or mixed carotenoids (MIX) by direct injection of known dosages. Vitamin A from feeder crickets (measured as retinol) was higher in insects supplemented with both BC and MIX; (P=0.0001) and plasma retinol concentrations were significantly higher in frogs fed MIX (P<0.02). Results suggest that both false tomato frogs and feeder crickets could receive some provitamin A activity through consumption of diets supplemented with β-carotene, and xanthophylls like lutein and zeaxanthin. Pigmentation was evaluated weekly through the use of visual color charts, as well as quantitatively using a hand-held spectrophotometer. MIX diets had a significant effect on skin color values (P<0.0001), as well as on lightness (P=0.0005) and hue (P=0.0022). Results indicated that frogs fed with BC changed to yellower colors, and frogs fed with MIX changed to oranger colors. Visual color chart observations also scored significantly different between CON and MIX diets (P<0.05); the animals fed MIX also appeared oranger according to the qualitative observations. Dietary supplements with carotenoids resulted in color changes and higher circulating retinol concentrations in false tomato frogs. These pigments may provide provitamin A activity in diets, thus may support improved nutrition and health of captive-fed insectivorous amphibians. © 2014 Wiley Periodicals Inc.
Enhancement of orographic precipitation in Jeju Island during the passage of Typhoon Khanun (2012)
NASA Astrophysics Data System (ADS)
Lee, Jung-Tae; Ko, Kyeong-Yeon; Lee, Dong-In; You, Cheol-Hwan; Liou, Yu-Chieng
2018-03-01
Typhoon Khanun caused over 226 mm of accumulated rainfall for 6 h (0700 to 1300 UTC), localized around the summit of Mt. Halla (height 1950 m), with a slanted rainfall pattern to the northeast. In this study, we investigated the enhancement mechanism for precipitation near the mountains as the typhoon passed over Jeju Island via dual-Doppler radar analysis and simple trajectory of passive tracers using a retrieved wind field. The analysis of vertical profiles of the mountain region show marked features matching the geophysical conditions. In the central mountain region, a strong wind (≥ 7 m s- 1) helps to lift low-level air up the mountain. The time taken for lifting is longer than the theoretical time required for raindrop growth via condensation. The falling particles (seeder) from the upper cloud were also one of the reasons for an increase in rainfall via the accretion process from uplifted cloud water (feeder). The lifted air and falling particles both contributed to the heavy rainfall in the central region. In contrast, on the leeward side, the seeder-feeder mechanism was important in the formation of strong radar reflectivity. The snow particles (above 5 km) were accelerated by strong downward winds (≤-6 m s- 1). Meanwhile, the nonlinear jumping flow (hydraulic jump) raised feeders (shifted from the windward side) to the upper level where particles fall. To support these development processes, a numerical simulation using cloud-resolving model theoretically carried out. The accreting of hydrometeors may be one of the key reasons why the lee side has strong radar reflectivity, and a lee side weighted rainfall pattern even though lee side includes no strong upward air motion.
Boumans, Iris J M M; de Boer, Imke J M; Hofstede, Gert Jan; Bokkers, Eddie A M
2018-04-26
Animals living in groups compete for food resources and face food conflicts. These conflicts are affected by social factors (e.g. competition level) and behavioural strategies (e.g. avoidance). This study aimed to deepen our understanding of the complex interactions between social factors and behavioural strategies affecting feeding and social interaction patterns in animals. We focused on group-housed growing pigs, Sus scrofa, which typically face conflicts around the feeder, and of which patterns in various competitive environments (i.e. pig:feeder ratio) have been documented soundly. An agent-based model was developed to explore how interactions among social factors and behavioural strategies can affect various feeding and social interaction patterns differently under competitive situations. Model results show that pig and diet characteristics interact with group size and affect daily feeding patterns (e.g. feed intake and feeding time) and conflicts around the feeder. The level of competition can cause a turning point in feeding and social interaction patterns. Beyond a certain point of competition, meal-based (e.g. meal frequency) and social interaction patterns (e.g. displacements) are determined mainly by behavioural strategies. The average daily feeding time can be used to predict the group size at which this turning point occurs. Under the model's assumptions, social facilitation was relatively unimportant in the causation of behavioural patterns in pigs. To validate our model, simulated patterns were compared with empirical patterns in conventionally housed pigs. Similarities between empirical and model patterns support the model results. Our model can be used as a tool in further research for studying the effects of social factors and group dynamics on individual variation in feeding and social interaction patterns in pigs, as well as in other animal species. Copyright © 2018 Elsevier Inc. All rights reserved.
Residue of organochlorine compounds and mercury in birds' eggs from the Niagara Peninsula, Ontario.
Frank, R; Holdrinet, M V
1975-01-01
Eggs (307) were collected in 1971 from twenty species of birds with a variety of feeding habits from the Niagara Peninsula. This area of ontario is intensively developed for agriculture and heavy industry and has a large urban population. Representative species were obtained from both the terrestrial and aquatic food chains. Eggs were analyzed for organochlorine insecticides, polychlorinated biphenyls, and total mercury. Eggs from carnivorous species at the top of the aquatic food chain had the highest mean residues of signa DDT(7.6to 22.4 pm), PCB (3.5 to 74.0 ppm) and total mercury (0.64 to 0.83 ppm). Eggs from some terrestrial carnivores (red-tailed hawk and great horned owl) also had relatively high residues (2.5 to 3.9 ppm of sigmaDDT, 0.2 to 1.0 ppm of PCB, 0.06 to 0.09 ppm of mercury, however levels were much lower than those found in eggs from aquatic-feeding carnivores. Eggs from one red-shouldered hawk had residues comparable to the aquatic feeding carnivores. Eggs from herbivorous and insectivorous birds of both aquatic and terrestrial environments contained much lower residues. PCB residues were slightly lower in eggs among the terrestrial feeding species (0.05 to 2.0 ppm) than among the aquatic feeders (0.14 to4.0 ppm) and tended to be lower in eggs from terrestrial species collected in rural than incity environs. Levels of sigmaDDT were similar in both groups with eggs from terrestrial feeders containing mean resisues between 0.15 and 2.64 ppm and those from aquatic feeders between 0.33 and 2.79 ppm.
Catalina, Puri; Montes, Rosa; Ligero, Gertru; Sanchez, Laura; de la Cueva, Teresa; Bueno, Clara; Leone, Paola E; Menendez, Pablo
2008-10-03
The use of human embryonic stem cells (hESCs) in research is increasing and hESCs hold the promise for many biological, clinical and toxicological studies. Human ESCs are expected to be chromosomally stable since karyotypic changes represent a pitfall for potential future applications. Recently, several studies have analysed the genomic stability of several hESC lines maintained after prolonged in vitro culture but controversial data has been reported. Here, we prompted to compare the chromosomal stability of three hESC lines maintained in the same laboratory using identical culture conditions and passaging methods. Molecular cytogenetic analyses performed in three different hESC lines maintained in parallel in identical culture conditions revealed significant differences among them in regard to their chromosomal integrity. In feeders, the HS181, SHEF-1 and SHEF-3 hESC lines were chromosomally stable up to 185 passages using either mechanical or enzymatic dissection methods. Despite the three hESC lines were maintained under identical conditions, each hESC line behaved differently upon being transferred to a feeder-free culture system. The two younger hESC lines, HS181 (71 passages) and SHEF-3 (51 passages) became chromosomally unstable shortly after being cultured in feeder-free conditions. The HS181 line gained a chromosome 12 by passage 17 and a marker by passage 21, characterized as a gain of chromosome 20 by SKY. Importantly, the mosaicism for trisomy 12 gradually increased up to 89% by passage 30, suggesting that this karyotypic abnormality provides a selective advantage. Similarly, the SHEF-3 line also acquired a trisomy of chromosome 14 as early as passage 10. However, this karyotypic aberration did not confer selective advantage to the genetically abnormal cells within the bulk culture and the level of mosaicism for the trisomy 14 remained overtime between 15%-36%. Strikingly, however, a much older hESC line, SHEF-1, which was maintained for 185 passages in feeders did not undergo any numerical or structural chromosomal change after 30 passages in feeder-free culture and over 215 passages in total. These results support the concept that feeder-free conditions may partially contribute to hESC chromosomal changes but also confirm the hypothesis that regardless of the culture conditions, culture duration or splitting methods, some hESC lines are inherently more prone than others to karyotypic instability.
An Alternative Method for Long-Term Culture of Chicken Embryonic Stem Cell In Vitro.
Zhang, Li; Wu, Yenan; Li, Xiang; Wei, Shao; Xing, Yiming; Lian, Zhengxing; Han, Hongbing
2018-01-01
Chicken embryonic stem cells (cESCs) obtained from stage X embryos provide a novel model for the study of avian embryonic development. A new way to maintain cESCs for a long period in vitro still remains unexplored. We found that the cESCs showed stem cell-like properties in vitro for a long term with the support of DF-1 feeder and basic culture medium supplemented with human basic fibroblast growth factor (hbFGF), mouse stem cell factor (mSCF), and human leukemia inhibitory factor (hLIF). During the long culture period, the cESCs showed typical ES cell morphology and expressed primitive stem cell markers with a relatively stable proliferation rate and high telomerase activity. These cells also exhibited the capability to differentiate into cardiac myocytes, smooth muscle cells, neural cells, osteoblast, and adipocyte in vitro . Chimera chickens were produced by cESCs cultured for 25 passages with this new culture system. The experiments showed that DF-1 was the optimal feeder and hbFGF was an important factor for maintaining the pluripotency of cESCs in vitro .
Quang, Tara; Marquez, Maribel; Blanco, Giselle; Zhao, Yuanxiang
2014-01-01
Many different culture systems have been developed for expanding human pluripotent stem cells (hESCs and hiPSCs). In general, 4-10 ng/ml of bFGF is supplemented in culture media in feeder-dependent systems regardless of feeder cell types, whereas in feeder-free systems, up to 100 ng/ml of bFGF is required for maintaining long-term culture on various substrates. The amount of bFGF required in native hESCs growth niche is unclear. Here we report using inactivated adipose-derived human mesenchymal stem cells as feeder cells to examine long-term parallel cultures of two hESCs lines (H1 and H9) and one hiPSCs line (DF19-9-7T) in media supplemented with 0, 0.4 or 4 ng/ml of bFGF for up to 23 passages, as well as parallel cultures of H9 and DF19 in media supplemented with 4, 20 or 100 ng/ml bFGF for up to 13 passages for comparison. Across all cell lines tested, bFGF supplement demonstrated inhibitory effect over growth expansion, single cell colonization and recovery from freezing in a dosage dependent manner. In addition, bFGF exerted differential effects on different cell lines, inducing H1 and DF19 differentiation at 4 ng/ml or higher, while permitting long-term culture of H9 at the same concentrations with no apparent dosage effect. Pluripotency was confirmed for all cell lines cultured in 0, 0.4 or 4 ng/ml bFGF excluding H1-4 ng, as well as H9 cultured in 4, 20 and 100 ng/ml bFGF. However, DF19 demonstrated similar karyotypic abnormality in both 0 and 4 ng/ml bFGF media while H1 and H9 were karyotypically normal in 0 ng/ml bFGF after long-term culture. Our results indicate that exogenous bFGF exerts dosage and cell line dependent effect on human pluripotent stem cells cultured on mesenchymal stem cells, and implies optimal use of bFGF in hESCs/hiPSCs culture should be based on specific cell line and its culture system.
Quang, Tara; Marquez, Maribel; Blanco, Giselle; Zhao, Yuanxiang
2014-01-01
Many different culture systems have been developed for expanding human pluripotent stem cells (hESCs and hiPSCs). In general, 4–10 ng/ml of bFGF is supplemented in culture media in feeder-dependent systems regardless of feeder cell types, whereas in feeder-free systems, up to 100 ng/ml of bFGF is required for maintaining long-term culture on various substrates. The amount of bFGF required in native hESCs growth niche is unclear. Here we report using inactivated adipose-derived human mesenchymal stem cells as feeder cells to examine long-term parallel cultures of two hESCs lines (H1 and H9) and one hiPSCs line (DF19-9-7T) in media supplemented with 0, 0.4 or 4 ng/ml of bFGF for up to 23 passages, as well as parallel cultures of H9 and DF19 in media supplemented with 4, 20 or 100 ng/ml bFGF for up to 13 passages for comparison. Across all cell lines tested, bFGF supplement demonstrated inhibitory effect over growth expansion, single cell colonization and recovery from freezing in a dosage dependent manner. In addition, bFGF exerted differential effects on different cell lines, inducing H1 and DF19 differentiation at 4 ng/ml or higher, while permitting long-term culture of H9 at the same concentrations with no apparent dosage effect. Pluripotency was confirmed for all cell lines cultured in 0, 0.4 or 4 ng/ml bFGF excluding H1-4 ng, as well as H9 cultured in 4, 20 and 100 ng/ml bFGF. However, DF19 demonstrated similar karyotypic abnormality in both 0 and 4 ng/ml bFGF media while H1 and H9 were karyotypically normal in 0 ng/ml bFGF after long-term culture. Our results indicate that exogenous bFGF exerts dosage and cell line dependent effect on human pluripotent stem cells cultured on mesenchymal stem cells, and implies optimal use of bFGF in hESCs/hiPSCs culture should be based on specific cell line and its culture system. PMID:24465853
EXTERIOR VIEW, LOOKING EAST, OF REDUCTION PLANT NO. 6 WITH ...
EXTERIOR VIEW, LOOKING EAST, OF REDUCTION PLANT NO. 6 WITH PRIMARY AND SECONDARY LIMESTONE REDUCTION ('CRUSHING') IN PROGRESS. FEEDER (RIGHT) FEEDS TO CONVEYOR BELTS (CENTER) AND CRUSHER (LEFT). LIMESTONE PROCESSED THROUGH THIS OPERATION IS FURTHER SCREENED AND PROCESSED AT ANOTHER PLANT ON THE THOMAS SITE. OPERATION OF THIS PLANT, WHICH BEGAN IN 1960, INCORPORATES WITHIN THE FEEDER A CONCRETE RETAINING WALL DATING TO A TURN OF THE CENTURY QUARRY OPERATION FORMERLY ON THIS SITE. - Wade Sand & Gravel Company, Reduction Plant No. 6, State Route 78, Thomas, Jefferson County, AL
NASA Astrophysics Data System (ADS)
Wu, Zhixiong; Huang, Rongjin; Huang, ChuanJun; Yang, Yanfang; Huang, Xiongyi; Li, Laifeng
2017-12-01
The Glass-fiber reinforced plastic (GFRP) fabricated by the vacuum bag process was selected as the high voltage electrical insulation and mechanical support for the superconducting joints and the current leads for the ITER Feeder system. To evaluate the cryogenic mechanical properties of the GFRP, the mechanical properties such as the short beam strength (SBS), the tensile strength and the fatigue fracture strength after 30,000 cycles, were measured at 77K in this study. The results demonstrated that the GFRP met the design requirements of ITER.
High pressure feeder and method of operating to feed granular or fine materials
DOE Office of Scientific and Technical Information (OSTI.GOV)
Vimalchand, Pannalal; Liu, Guohai; Peng, Wan Wang
2014-10-07
A coal feed system to feed pulverized low rank coals containing up to 25 wt % moisture to gasifiers operating up to 1000 psig pressure is described. The system includes gas distributor and collector gas permeable pipes imbedded in the lock vessel. Different methods of operation of the feed system are disclosed to minimize feed problems associated with bridging and packing of the pulverized coal. The method of maintaining the feed system and feeder device exit pressures using gas addition or extraction with the pressure control device is also described.
RF model of the distribution system as a communication channel, phase 2. Volume 2: Task reports
NASA Technical Reports Server (NTRS)
Rustay, R. C.; Gajjar, J. T.; Rankin, R. W.; Wentz, R. C.; Wooding, R.
1982-01-01
Based on the established feasibility of predicting, via a model, the propagation of Power Line Frequency on radial type distribution feeders, verification studies comparing model predictions against measurements were undertaken using more complicated feeder circuits and situations. Detailed accounts of the major tasks are presented. These include: (1) verification of model; (2) extension, implementation, and verification of perturbation theory; (3) parameter sensitivity; (4) transformer modeling; and (5) compensation of power distribution systems for enhancement of power line carrier communication reliability.
36. INTERIOR VIEW LOOKING WEST FROM UNDERNEATH THE ORE BINS ...
36. INTERIOR VIEW LOOKING WEST FROM UNDERNEATH THE ORE BINS LOOKING AT THE BACK SIDE OF THE HENDY CHALLENGE CONTINUOUS ORE FEEDERS, #1 IS ON THE LEFT, #2 IS CENTER, AND #3 IS ON THE RIGHT. THESE ARE USED TO KEEP A CONTINUOUS FLOW OF ORE INTO THE STAMP MILLS. NOTE THE SPARE FEEDER DISKS ON THE FLOOR BOTTOM CENTER AND SPARE STAMP HEADS AND SHOES ON THE FLOOR BOTTOM LEFT OF THE IMAGE. - Standard Gold Mill, East of Bodie Creek, Northeast of Bodie, Bodie, Mono County, CA
High pressure feeder and method of operating to feed granular or fine materials
DOE Office of Scientific and Technical Information (OSTI.GOV)
Vimalchand, Pannalal; Liu, Guohai; Peng, Wan Wang
A coal feed system to feed pulverized low rank coals containing up to 25 wt % moisture to gasifiers operating up to 1000 psig pressure is described. The system includes gas distributor and collector gas permeable pipes imbedded in the lock vessel. Different methods of operation of the feed system are disclosed to minimize feed problems associated with bridging and packing of the pulverized coal. The method of maintaining the feed system and feeder device exit pressures using gas addition or extraction with the pressure control device is also described.
DOE Office of Scientific and Technical Information (OSTI.GOV)
Zamzam, Ahmed, S.; Zhaoy, Changhong; Dall'Anesey, Emiliano
This paper examines the AC Optimal Power Flow (OPF) problem for multiphase distribution networks featuring renewable energy resources (RESs). We start by outlining a power flow model for radial multiphase systems that accommodates wye-connected and delta-connected RESs and non-controllable energy assets. We then formalize an AC OPF problem that accounts for both types of connections. Similar to various AC OPF renditions, the resultant problem is a non convex quadratically-constrained quadratic program. However, the so-called Feasible Point Pursuit-Successive Convex Approximation algorithm is leveraged to obtain a feasible and yet locally-optimal solution. The merits of the proposed solution approach are demonstrated usingmore » two unbalanced multiphase distribution feeders with both wye and delta connections.« less
NASA Technical Reports Server (NTRS)
Rivera, J. M.; Simpson, R. W.
1980-01-01
The aerial relay system network design problem is discussed. A generalized branch and bound based algorithm is developed which can consider a variety of optimization criteria, such as minimum passenger travel time and minimum liner and feeder operating costs. The algorithm, although efficient, is basically useful for small size networks, due to its nature of exponentially increasing computation time with the number of variables.
Movahednia, Mohammad Mehdi; Kidwai, Fahad Karim; Zou, Yu; Tong, Huei Jinn; Liu, Xiaochen; Islam, Intekhab; Toh, Wei Seong; Raghunath, Michael; Cao, Tong
2015-04-01
Culture microenvironment plays a critical role in the propagation and differentiation of human embryonic stem cells (hESCs) and their differentiated progenies. Although high efficiency of hESC differentiation to keratinocytes (hESC-Kert) has been achieved, little is known regarding the effects of early culture microenvironment and pertinent extracellular matrix (ECM) interactions during epidermal commitment on subsequent proliferative capacity of hESC-Kert. The aim of this study is to evaluate the effects of the different ECM microenvironments during hESC differentiation on subsequent replicative life span of hESC-Kert. In doing so, H1-hESCs were differentiated to keratinocytes (H1-Kert) in two differentiation systems. The first system employed autologous fibroblast feeder support, in which keratinocytes (H1-Kert(ACC)) were derived by coculture of hESCs with hESC-derived fibroblasts (H1-ebFs). The second system employed a novel decellularized matrix from H1-ebFs to create a dermoepidermal junction-like (DEJ) matrix. H1-Kert(AFF) were derived by differentiation of hESCs on the feeder-free system employing the DEJ matrix. Our study indicated that the feeder-free system with the use of DEJ matrix was more efficient in differentiation of hESCs toward epidermal progenitors. However, the feeder-free system was not sufficient to support the subsequent replicative capacity of differentiated keratinocytes. Of note, H1-Kert(AFF) showed limited replicative capacity with reduced telomere length and early cellular senescence. We further showed that the lack of cell-cell interactions during epidermal commitment led to heightened production of TGF-β1 by hESC-Kert during extended culture, which in turn was responsible for resulting in the limited replicative life span with cellular senescence of hESC-Kert derived under the feeder-free culture system. This study highlights for the first time the importance of the culture microenvironment and cell-ECM interactions during differentiation of hESCs on subsequent replicative life span and cellular senescence of the differentiated keratinocytes, with implications for use of these cells for applications in tissue engineering and regenerative medicine.
Hydrodynamics of microbial filter feeding
Asadzadeh, Seyed Saeed; Dölger, Julia; Walther, Jens H.; Andersen, Anders
2017-01-01
Microbial filter feeders are an important group of grazers, significant to the microbial loop, aquatic food webs, and biogeochemical cycling. Our understanding of microbial filter feeding is poor, and, importantly, it is unknown what force microbial filter feeders must generate to process adequate amounts of water. Also, the trade-off in the filter spacing remains unexplored, despite its simple formulation: A filter too coarse will allow suitably sized prey to pass unintercepted, whereas a filter too fine will cause strong flow resistance. We quantify the feeding flow of the filter-feeding choanoflagellate Diaphanoeca grandis using particle tracking, and demonstrate that the current understanding of microbial filter feeding is inconsistent with computational fluid dynamics (CFD) and analytical estimates. Both approaches underestimate observed filtration rates by more than an order of magnitude; the beating flagellum is simply unable to draw enough water through the fine filter. We find similar discrepancies for other choanoflagellate species, highlighting an apparent paradox. Our observations motivate us to suggest a radically different filtration mechanism that requires a flagellar vane (sheet), something notoriously difficult to visualize but sporadically observed in the related choanocytes (sponges). A CFD model with a flagellar vane correctly predicts the filtration rate of D. grandis, and using a simple model we can account for the filtration rates of other microbial filter feeders. We finally predict how optimum filter mesh size increases with cell size in microbial filter feeders, a prediction that accords very well with observations. We expect our results to be of significance for small-scale biophysics and trait-based ecological modeling. PMID:28808016
Hydrodynamics of microbial filter feeding.
Nielsen, Lasse Tor; Asadzadeh, Seyed Saeed; Dölger, Julia; Walther, Jens H; Kiørboe, Thomas; Andersen, Anders
2017-08-29
Microbial filter feeders are an important group of grazers, significant to the microbial loop, aquatic food webs, and biogeochemical cycling. Our understanding of microbial filter feeding is poor, and, importantly, it is unknown what force microbial filter feeders must generate to process adequate amounts of water. Also, the trade-off in the filter spacing remains unexplored, despite its simple formulation: A filter too coarse will allow suitably sized prey to pass unintercepted, whereas a filter too fine will cause strong flow resistance. We quantify the feeding flow of the filter-feeding choanoflagellate Diaphanoeca grandis using particle tracking, and demonstrate that the current understanding of microbial filter feeding is inconsistent with computational fluid dynamics (CFD) and analytical estimates. Both approaches underestimate observed filtration rates by more than an order of magnitude; the beating flagellum is simply unable to draw enough water through the fine filter. We find similar discrepancies for other choanoflagellate species, highlighting an apparent paradox. Our observations motivate us to suggest a radically different filtration mechanism that requires a flagellar vane (sheet), something notoriously difficult to visualize but sporadically observed in the related choanocytes (sponges). A CFD model with a flagellar vane correctly predicts the filtration rate of D. grandis , and using a simple model we can account for the filtration rates of other microbial filter feeders. We finally predict how optimum filter mesh size increases with cell size in microbial filter feeders, a prediction that accords very well with observations. We expect our results to be of significance for small-scale biophysics and trait-based ecological modeling.
Cumming, Mark J; Thompson, Madison A; McCormick, Cheryl M
2014-11-01
Adolescent social instability stress (SS; daily 1 hr isolation + new cage partners postnatal days 30-45; thereafter with original cage partner, also in the SS condition) and control (CTL) rats competed for access to a preferred food in five sessions against their cage partner. In the first session, SS pairs displayed more aggression (face whacks, p = .02; rear attacks, p = .03), were less likely to relinquish access to the food voluntarily (p = .03), spent more time at the feeder than CTL pairs (p = .06), but did not differ in latency to access the feeder (p = .41). Pairs were considered in dominant-submissive relationships (DSR) if one rat spent significantly more time at the feeder than the other; 8 of 12 SS and 8 of 12 CTL pairs displayed DSRs (remaining: no-DSR). Aggression increased from the 1st to 5th session (p < .001), was greater in no-DSR than DSR pairs (p = .04; consistent with the proposed function of DSRs to be the reduction of aggression in groups), and was higher in SS than CTL pairs (p = .05). Because the increased aggression of SS compared with CTL pairs did not result in a significant increase in their time at the feeder, the increased aggression may be considered maladaptive, and may reflect an increased motivation for food reward. These results add to evidence that SS in adolescence modifies the adult social repertoire of rats and highlight the importance of adolescent social experiences for adult behavior. © 2014 Wiley Periodicals, Inc.
NASA Astrophysics Data System (ADS)
Olóriz, Federico; Reolid, Matías; Rodríguez-Tovar, Francisco J.
2006-11-01
The palaeoenvironmental conditions and trophic structure of a mid-outer neritic biota (microfossils, mainly forams, and macroinvertebrate assemblages) have been approached in middle Oxfordian-lowermost Kimmeridgian deposits from the Prebetic Zone (Betic Cordillera) in south-eastern Spain. According to relationships between fossil assemblages and lithofacies, a general seaward trend is identified which displays decreasing sedimentation rates and nutrient inputs, but increasing substrate consistency and presumably depth. Midshelf, terrigenous-rich deposits in the External Prebetic relate to the highest sedimentation rates and nutrient availability. These two parameters correlate with the highest content in vagile-benthic, calcareous perforate, epifaunal forams, as well as with potentially deep infaunal forams and infaunal macroinvertebrates. Outer-shelf lumpy deposits in the Internal Prebetic show the lowest sedimentation rates and nutrient availability and the highest records for macro-micro nektonics and planktics. In contrast, vagile-benthic, calcareous perforate epifaunal and potentially deep infaunal forams are scarcer in the midshelf environments. Colonial encrusting forams, benthic microbial communities and sessile benthic macro-invertebrates increase from the middle to outer shelf. Trophic-analysis structuring through the integration of benthic microbial communities, foraminiferal and macroinvertebrate fossil assemblages makes it possible to interpret: (a) a trophic-level frame composed of producers and primary and secondary consumers; (b) a main trophic-group differentiation in suspension-feeders, detritus-feeders, browsers, grazers, carnivores and scavengers; (c) a preliminary approach to food-chain structure supported by suspension-feeders, deposit-feeders and predators (active prey-selection carnivores); and (d) a food-pyramid model, which takes into account both recorded fossils and envisaged —i.e., ecologically inferred-organisms.
Peters, Brenton C; Fitzgerald, Christopher J
2006-10-01
Laboratory and field data reported in the literature are confusing with regard to "adequate" protection thresholds for borate timber preservatives. The confusion is compounded by differences in termite species, timber species and test methodology. Laboratory data indicate a borate retention of 0.5% mass/mass (m/m) boric acid equivalent (BAE) would cause > 90% termite mortality and restrict mass loss in test specimens to < or = 5%. Field data generally suggest that borate retentions appreciably > 0.5% m/m BAE are required. We report two field experiments with varying amounts of untreated feeder material in which Coptotermes acinaciformis (Froggatt) (Isoptera: Rhinotermitidae) responses to borate-treated radiata (Monterey) pine, Pinus radiata D. Don, were measured. The apparently conflicting results between laboratory and field data are explained by the presence or absence of untreated feeder material in the test environment. In the absence of untreated feeder material, wood containing 0.5% BAE provided adequate protection from Coptotermes sp., whereas in the presence of untreated feeder material, increased retentions were required. Furthermore, the retentions required increased with increased amounts of susceptible material present. Some termites, Nasutitermes sp. and Mastotermes darwiniensis Froggatt, for example, are borate-tolerant and borate timber preservatives are not a viable management option with these species. The lack of uniform standards for termite test methodology and assessment criteria for efficacy across the world is recognized as a difficulty with research into the performance of timber preservatives with termites. The many variables in laboratory and field assays make "prescriptive" standards difficult to recommend. The use of "performance" standards to define efficacy criteria ("adequate" protection) is discussed.
Utility of human hepatocyte spheroids without feeder cells for evaluation of hepatotoxicity.
Ogihara, Takuo; Arakawa, Hiroshi; Jomura, Tomoko; Idota, Yoko; Koyama, Satoshi; Yano, Kentaro; Kojima, Hajime
2017-01-01
We investigated the utility of three-dimensionally cultured hepatocytes (spheroids) without feeder cells (Sph(f-)) for the prediction of drug-induced liver injury (DILI) in humans. Sph(f-) and spheroids cultured on feeder cells (Sph(f+)) were exposed to the hepatotoxic drugs flutamide, diclofenac, isoniazid and chlorpromazine at various concentrations for 14 days, and albumin secretion and cumulative leakages of toxicity marker enzymes, aspartate aminotransferase (AST), alanine aminotransferase (ALT), lactate dehydrogenase (LDH) and γ-glutamyl transpeptidase (γ-GTP), were measured. The cumulative AST, LDH or γ-GTP leakages from Sph(f-) were similar to or greater than those from Sph(f+) for all drugs tested, although ALT leakages showed no consistent difference between Sph(f+) and Sph(f-). In the case of Sph(f-), significant correlations among all the toxicity markers except for γ-GTP were observed. As regards the drug concentrations causing 1.2-fold elevation of enzyme leakage (F 1.2 ), no consistent difference between Sph(f+) and Sph(f-) was found, although several F 1.2 values were undetermined, especially in Sph(f+). The IC 50 of albumin secretion and F 1.2 of AST leakage from Sph(f-) were equal to or lower than those of Sph(f+) for all the tested drugs. These results indicate that feeder cells might contribute to resistance to hepatotoxicity, suggesting DILI could be evaluated more accurately by using Sph(f-). We suggest that long-term exposure of Sph(f-) to drugs might be a versatile method to predict and reproduce clinical chronic toxicity, especially in response to repeated drug administration.
Advanced Energy Storage Management in Distribution Network
DOE Office of Scientific and Technical Information (OSTI.GOV)
Liu, Guodong; Ceylan, Oguzhan; Xiao, Bailu
2016-01-01
With increasing penetration of distributed generation (DG) in the distribution networks (DN), the secure and optimal operation of DN has become an important concern. In this paper, an iterative mixed integer quadratic constrained quadratic programming model to optimize the operation of a three phase unbalanced distribution system with high penetration of Photovoltaic (PV) panels, DG and energy storage (ES) is developed. The proposed model minimizes not only the operating cost, including fuel cost and purchasing cost, but also voltage deviations and power loss. The optimization model is based on the linearized sensitivity coefficients between state variables (e.g., node voltages) andmore » control variables (e.g., real and reactive power injections of DG and ES). To avoid slow convergence when close to the optimum, a golden search method is introduced to control the step size and accelerate the convergence. The proposed algorithm is demonstrated on modified IEEE 13 nodes test feeders with multiple PV panels, DG and ES. Numerical simulation results validate the proposed algorithm. Various scenarios of system configuration are studied and some critical findings are concluded.« less
Optimal Power Flow in Multiphase Radial Networks with Delta Connections: Preprint
DOE Office of Scientific and Technical Information (OSTI.GOV)
Zhao, Changhong; Dall-Anese, Emiliano; Low, Steven H.
This paper focuses on multiphase radial distribution networks with mixed wye and delta connections, and proposes a semidefinite relaxation of the AC optimal power flow (OPF) problem. Two multiphase power-flow models are developed to facilitate the integration of delta-connected generation units/loads in the OPF problem. The first model extends traditional branch flow models - and it is referred to as extended branch flow model (EBFM). The second model leverages a linear relationship between per-phase power injections and delta connections, which holds under a balanced voltage approximation (BVA). Based on these models, pertinent OPF problems are formulated and relaxed to semidefinitemore » programs (SDPs). Numerical studies on IEEE test feeders show that SDP relaxations can be solved efficiently by a generic optimization solver. Numerical evidences indicate that solving the resultant SDP under BVA is faster than under EBFM. Moreover, both SDP solutions are numerically exact with respect to voltages and branch flows. It is also shown that the SDP solution under BVA has a small optimality gap, while the BVA model is accurate in the sense that it reflects actual system voltages.« less
Continuous powder feeding for pharmaceutical solid dosage form manufacture: a short review.
Blackshields, Caroline A; Crean, Abina M
2018-07-01
There has been a noticeable shift from pharmaceutical batch processing towards a more continuous mode of manufacture for solid oral dosage forms. Continuous solid oral dose processes would not be possible in the absence of a highly accurate feeding system. The performance of feeders defines the content of formulations and is therefore a critical operation in continuous manufacturing of solid dosage forms. It was the purpose of this review to review the role of the initial powder feeding step in a continuous manufacturing process. Different feeding mechanisms are discussed with a particular emphasis on screw controlled loss in weight (LIW) feeding. The importance of understanding the physical properties of the raw materials and its impact on the feeding process is reviewed. Prior knowledge of materials provides an initial indication of how the powders will behave through processing and facilitates in the selection of the most suitable (i) feeder (capacity), (ii) feeding mechanism, and (iii) in the case of screw feeder - screw type. The studies identified in this review focus on the impact of material on powder feeding performance.
Tirakotai, W; Benes, L; Kappus, C; Sure, U; Farhoud, A; Bien, S; Bertalanffy, H
2007-01-01
Dural arteriovenous fistulas located in the vicinity of the jugular foramen are complex vascular malformations and belong to the most challenging skull base lesions to treat. The authors comprehensively analyze multiple features in a series of dural arteriovenous fistulas with transosseous arterial feeders involving the jugular bulb. Four patients who underwent surgery via the transcondylar approach to treat dural arteriovenous fistulas around the jugular foramen were retrospectively reviewed. Previously, endovascular treatment was attempted in all patients. The success of the surgical treatment was examined with postoperative angiography. Complete obliteration of the dural arteriovenous fistulas (DAVFs) was achieved in three patients, and significant flow reduction in one individual. All patients had a good postoperative outcome, and only one experienced mild hypoglossal nerve palsy. Despite extensive bone drilling, an occipitocervical fusion was necessary in only one patient with bilateral lesions. The use of an individually tailored transcondylar approach to treat dural arteriovenous fistulas at the region of the jugular foramen is most effective. This approach allows for complete obliteration of the connecting arterial feeders, and removal of bony structures containing pathological vessels.
Reconstituted human gingival epithelium: nonsubmerged in vitro model.
Delcourt-Huard, A; Corlu, A; Joffre, A; Magloire, H; Bonnaure-Mallet, M
1997-01-01
Many studies have shown that human gingival keratinocytes grown in submerged culture fail to attain optimal differentiation. This study reports an in vitro culture system for oral gingival epithelial cells, in which they are grown at the air-liquid interface, on polycarbonate inserts, in the presence of an NIH-3T3 feeder layer. This model was compared with two submerged culture methods for gingival keratinocytes, on type 1 collagen gel and on an NIH-3T3 feeder layer. Transmission electron microscopy showed an advanced level of stratification (over six layers of cells) for cultures grown at the air-liquid interface. Immunofluorescence and electrophoretic patterns showed the presence of cytokeratins 10 and 11 in cytoskeletal protein extracts of these cultured keratinocytes. In this air-liquid interface culture model, in the presence of NIH-3T3 feeder cells, keratinocytes can achieve an advanced level of stratification and differentiation and a resemblance to in vivo gingiva. The obtention of a highly differentiated epithelium will permit in vitro pharmacological studies and studies on the biocompatability of certain alloys with the superficial periodontium; it will also provide grafts for patients undergoing periodontal surgery.
Alavez-Rosas, David; Malo, Edi A; Guzmán, Miguel A; Sánchez-Guillén, Daniel; Villanueva-Gutiérrez, Rogel; Cruz-López, Leopoldo
2017-10-01
Stingless bees foraging for food improve recruitment by depositing chemical cues on valuable food sites or pheromone marks on vegetation. Using gas chromatography/mass spectrometry and bioassays, we showed that Melipona solani foragers leave a mixture composed mostly of long chain hydrocarbons from their abdominal cuticle plus methyl oleate from the labial gland as a scent mark on rich food sites. The composition of hydrocarbons was highly variable among individuals and varied in proportions, depending on the body part. A wide ratio of compounds present in different body parts of the bees elicited electroantennogram responses from foragers and these responses were dose dependent. Generally, in bioassays, these bees prefer to visit previously visited feeders and feeders marked with extracts from any body part of conspecifics. The mean number of visits to a feeder was enhanced when synthetic methyl oleate was added. We propose that this could be a case of multi-source odor marking, in which hydrocarbons, found in large abundance, act as a signature mixture with attraction enhanced through deposition of methyl oleate, which may indicate a rich food source.
Power Hardware-in-the-Loop Evaluation of PV Inverter Grid Support on Hawaiian Electric Feeders
DOE Office of Scientific and Technical Information (OSTI.GOV)
Nelson, Austin A; Prabakar, Kumaraguru; Nagarajan, Adarsh
As more grid-connected photovoltaic (PV) inverters become compliant with evolving interconnections requirements, there is increased interest from utilities in understanding how to best deploy advanced grid-support functions (GSF) in the field. One efficient and cost-effective method to examine such deployment options is to leverage power hardware-in-the-loop (PHIL) testing methods, which combine the fidelity of hardware tests with the flexibility of computer simulation. This paper summarizes a study wherein two Hawaiian Electric feeder models were converted to real-time models using an OPAL-RT real-time digital testing platform, and integrated with models of GSF capable PV inverters based on characterization test data. Themore » integrated model was subsequently used in PHIL testing to evaluate the effects of different fixed power factor and volt-watt control settings on voltage regulation of the selected feeders using physical inverters. Selected results are presented in this paper, and complete results of this study were provided as inputs for field deployment and technical interconnection requirements for grid-connected PV inverters on the Hawaiian Islands.« less
Breast feeding, bottle feeding, and maternal autonomic responses to stress.
Mezzacappa, Elizabeth Sibolboro; Kelsey, Robert M; Katkin, Edward S
2005-04-01
The aim of this study was to examine the effects of breast feeding on autonomic nervous system (ANS) response to stressors. Sympathetic and parasympathetic activities were examined before, during, and after standard laboratory stressors in women who were either exclusively breast feeding (n=14) or nonexclusively breast feeding (n=14), and in non-postpartum controls (n=15). Mothers who breast fed exclusively showed greater levels of parasympathetic cardiac modulation and slower heart rate (HR) throughout the session and less HR increase and preejection period (PEP) shortening to mental arithmetic (MA) than did nonexclusive breast feeders and controls. Nonexclusive breast-feeders showed greater electrodermal reactivity to, and greater differences in skin conductance response (SCR) frequency between baseline and recovery from cold pressor (CP) than did either exclusive breast-feeders or controls. Sympathetic activity was negatively related to the number of breast feedings and positively related to bottle feedings. Breast feeding shifts maternal ANS balance toward relatively greater parasympathetic and lesser sympathetic activity; the opposite occurs with bottle feeding. The frequency of feeding also is a critical factor in determining breast feeding effects on maternal ANS function.
Cambrian cinctan echinoderms shed light on feeding in the ancestral deuterostome
Rahman, Imran A.; Zamora, Samuel; Falkingham, Peter L.; Phillips, Jeremy C.
2015-01-01
Reconstructing the feeding mode of the latest common ancestor of deuterostomes is key to elucidating the early evolution of feeding in chordates and allied phyla; however, it is debated whether the ancestral deuterostome was a tentaculate feeder or a pharyngeal filter feeder. To address this, we evaluated the hydrodynamics of feeding in a group of fossil stem-group echinoderms (cinctans) using computational fluid dynamics. We simulated water flow past three-dimensional digital models of a Cambrian fossil cinctan in a range of possible life positions, adopting both passive tentacular feeding and active pharyngeal filter feeding. The results demonstrate that an orientation with the mouth facing downstream of the current was optimal for drag and lift reduction. Moreover, they show that there was almost no flow to the mouth and associated marginal groove under simulations of passive feeding, whereas considerable flow towards the animal was observed for active feeding, which would have enhanced the transport of suspended particles to the mouth. This strongly suggests that cinctans were active pharyngeal filter feeders, like modern enteropneust hemichordates and urochordates, indicating that the ancestral deuterostome employed a similar feeding strategy. PMID:26511049
Photovoltaic Hosting Capacity of Feeders with Reactive Power Control and Tap Changers
DOE Office of Scientific and Technical Information (OSTI.GOV)
Ceylan, Oğuzhan; Paudyal, Sumit; Bhattarai, Bishnu P.
This paper proposes an algorithm to determine photovoltaic (PV) hosting capacity of power distribution networks as a function of number of PV injection nodes, reactive power support from the PVs, and the sub-station load tap changers (LTCs). In the proposed method, several minute by minute simulations are run based on randomly chosen PV injection nodes, daily PV output profiles, and daily load profiles from a pool of high-resolution realistic data set. The simulation setup is built using OpenDSS and MATLAB. The performance of the proposed method is investigated in the IEEE 123-node distribution feeder for multiple scenarios. The case studiesmore » are performed particularly for one, two, five and ten PV injection nodes, and looking at the maximum voltage deviations. Case studies show that the PV hosting capacity of the 123-node feeder greatly differs with the number of PV injection nodes. We have also observed that the PV hosting capacity increases with reactive power support and higher tap position of sub-station LTC.« less
Feeding methods and efficiencies of selected frugivorous birds
Foster, M.S.
1987-01-01
I report on handling methods and efficiencies of 26 species of Paraguayan birds freeding on fruits of Allophyllus edulis (Sapindaceae). A bird may swallow fruits whole (Type I: pluck and swallow feeders), hold a fruit and cut the pulp from the seed with the edge of the bill, swallowing the pulp but not the seed (Type II: cut or mash feeders), or take bites of pulp from a fruit that hangs from the tree or that is held and manipulated against a branch (Type III: push and bite feeders). In terms of absolute amount of pulp obtained from a fruit, and amount obtained per unit time. Type I species are far more efficient than Type II and III species. Bill morphology influences feeding methods but is not the only important factor. Diet breadth does not appear to be significant. Consideration of feeding efficiency relative to the needs of the birds indicates that these species need to spend relatively little time feeding to meet their estimated energetic needs, and that handling time has a relatively trivial effect on the time/energy budges of the bird species observed.
Orographic enhancement of rainfalls in the Rio San Francisco valley in southern Ecuador
NASA Astrophysics Data System (ADS)
Trachte, K.; Rollenbeck, R.; Bendix, J.
2012-04-01
In a tropical mountain rain forest in southern Ecuador diurnal dynamics of cloud development and precipitation behavior is investigated in the framework of the DFG research unit 816. With automatic climate stations and rain radar rainfalls in the Rio San Francisco valley are recorded. The observations showed the typical tropical late afternoon convective precipitation as well as local events such as mountain valley breezes and luv-lee effects. Additionally, the data revealed an unusually early morning peak that could be recognized as convective rainfalls. On the basis of GOES-E satellite imagery these rainfalls could be traced back to nocturnal convective clouds at the eastern Andes Mountains. There are some explanations for the occurrence of the clouds: One already examined mechanism is a katabatic induced cold front at the foothills of the Andes in the Peruvian Amazon basin. In this region the mountains form a quasi-concave configuration that contributes to a convergence of cold air drainage with subsequent convective activities. Another explanation for the events is the orographic enhancement by a local seeder-feeder mechanism. Mesoscale convective systems from the Amazon basin are transported to the west via the trade winds. At the Andes Mountains the complex and massive orography acts like a barrier to the clouds. The result is a disconnection of the upper part of the cloud from the lower part. The latter rains out at the eastern slopes and the upper cloud is transported further to the west. There it acts like a seeder to lower level clouds, i. e. the feeder. With the numerical model ARPS (Advanced Regional Prediction System) this procedure is investigated on the basis of two case studies. The events are detected and selected through the analysis of GOES-E brightness temperatures. They are also used to compare and validate the results of the model. Finally, the orographic enhancement of the clouds is examined. By using a vertically pointing radar the development of the resulting precipitation is analyzed and discussed in the context of a seeder-feeder mechanism.
Automatic real-time pair-feeding system for animals
NASA Technical Reports Server (NTRS)
Leon, H. A.; Connolly, J. P.; Hitchman, M. J.; Humbert, J. E. (Inventor)
1974-01-01
A pair feeding method and apparatus are provided for experimental animals wherein the amount of food consumed is immediately delivered to a normal or control animal so that there is a qualitative, quantitative and chronological correctness in the pair feeding of the two animals. This feeding mechanism delivers precisely measured amounts of food to a feeder. Circuitry is provided between master and slave feeders so that there is virtually no chance of a malfunction of the feeding apparatus, causing erratic results. Recording equipment is also provided so that an hourly record is kept of food delivery.
Records of the brambling in North America
Banks, Richard C.
1970-01-01
A Brambling, Fringella montifringella, was seen regularly in Portland, Oregon, from 22 November 1967 to 3 April 1968 and photographed by many people. First discovered at a feeder in the northeast section of the city by Jeff Gilligan and Ron Klein, from January on it was a daily visitor to the feeder of the Albert H. Praels in the same part of Portland. The bird, judged by plumage to be a male, fed regularly with House Finches (Carpodacus mexicanus) on sunflower seeds. The occurrence of this individual in Portland was recorded in Audubon Field Notes (22: 471, 1968) without detail.
Method and apparatus for anti-islanding protection of distributed generations
Ye, Zhihong; John, Vinod; Wang, Changyong; Garces, Luis Jose; Zhou, Rui; Li, Lei; Walling, Reigh Allen; Premerlani, William James; Sanza, Peter Claudius; Liu, Yan; Dame, Mark Edward
2006-03-21
An apparatus for anti-islanding protection of a distributed generation with respect to a feeder connected to an electrical grid is disclosed. The apparatus includes a sensor adapted to generate a voltage signal representative of an output voltage and/or a current signal representative of an output current at the distributed generation, and a controller responsive to the signals from the sensor. The controller is productive of a control signal directed to the distributed generation to drive an operating characteristic of the distributed generation out of a nominal range in response to the electrical grid being disconnected from the feeder.
Three-dimensional effects for radio frequency antenna modeling
DOE Office of Scientific and Technical Information (OSTI.GOV)
Carter, M.D.; Batchelor, D.B.; Stallings, D.C.
1993-09-01
Electromagnetic field calculations for radio frequency (rf) antennas in two dimensions (2-D) neglect finite antenna length effects as well as the feeders leading to the main current strap. Comparisons with experiments indicate that these 2-D calculations can overestimate the loading of the antenna and fail to give the correct reactive behavior. To study the validity of the 2-D approximation, the Multiple Antenna Implementation System (MAntIS) has been used to perform 3-D modeling of the power spectrum, plasma loading, and inductance for a relevant loop antenna design. Effects on antenna performance caused by feeders to the main current strap, conducting sidewalls,more » and finite phase velocity are considered. The plasma impedance matrix for the loading calculation is generated by use of the ORION-1D code. The 3-D model is benchmarked with the 2-D model in the 2-D limit. For finite-length antennas, inductance calculations are found to be in much more reasonable agreement with experiments for 3-D modeling than for the 2-D estimates. The modeling shows that the feeders affect the launched power spectrum in an indirect way by forcing the driven rf current to return in the antenna sidewalls rather than in the plasma as in the 2-D model. Thus, the feeders have much more influence than the plasma on the currents that return in the sidewall. It has also been found that poloidal dependencies in the plasma impedance matrix can reduce the loading from that predicted in the 2-D model. For some plasma parameters, the combined 3-D effects can lead to a reduction in the predicted loading by as much as a factor of 2 from that given by the 2-D model.« less
Clarençon, Frédéric; Di Maria, Federico; Cormier, Evelyne; Gaudric, Julien; Sourour, Nader; Gabrieli, Joseph; Iosif, Christina; Jenny, Catherine; Koskas, Fabien; Chiras, Jacques
2013-11-01
The aim of this study was to compare the sensitivity of intra-aortic computed tomography angiography (IA-CTA) to that of regular spinal digital subtraction angiography for the presurgical location of the Adamkiewicz artery (AKA). Thirty patients (21 males, 9 females; mean age 64 years) had an IA-CTA for the location of the AKA before surgery of aneurysm (n = 24) or dissection (n = 6) of the thoracoabdominal aorta. After femoral artery puncture, a pigtail catheter was positioned at the origin of the descending aorta. CT acquisition was performed with an intra-aortic iodinated contrast media injection (15 mL/s, 120 mL). The visualization of the AKA and the location of the feeder(s) to the AKA were independently evaluated by two observers. Interrater agreement was calculated using a kappa test. Spinal angiogram by selective catheterization was systematically performed to confirm the results of the IA-CTA. The AKA was visualized by the IA-CTA in 27/30 cases (90 %); in 26/31 (84 %) cases, the continuity with the aorta was satisfactorily seen. Interrater agreement was good for the visualization of the AKA and its feeder(s): 0.625 and 0.87, respectively. In 75 % of the cases for which the AKA was visualized, the selective catheterization confirmed the results of the IA-CTA. In the remaining 25 % of the cases, the selective catheterization could not be performed due to marked vessels' tortuosity or ostium stenosis. IA-CTA is a feasible technique in a daily practice that presents a good sensitivity for the location of the AKA.