Science.gov

Sample records for final cut express

  1. Advanced cryogenics for cutting tools. Final report

    SciTech Connect

    Lazarus, L.J.

    1996-10-01

    The purpose of the investigation was to determine if cryogenic treatment improved the life and cost effectiveness of perishable cutting tools over other treatments or coatings. Test results showed that in five of seven of the perishable cutting tools tested there was no improvement in tool life. The other two tools showed a small gain in tool life, but not as much as when switching manufacturers of the cutting tool. The following conclusions were drawn from this study: (1) titanium nitride coatings are more effective than cryogenic treatment in increasing the life of perishable cutting tools made from all cutting tool materials, (2) cryogenic treatment may increase tool life if the cutting tool is improperly heat treated during its origination, and (3) cryogenic treatment was only effective on those tools made from less sophisticated high speed tool steels. As a part of a recent detailed investigation, four cutting tool manufacturers and two cutting tool laboratories were queried and none could supply any data to substantiate cryogenic treatment of perishable cutting tools.

  2. Characterization of metal cutting dynamics. Final report

    SciTech Connect

    Berger, B.S.; Minis, I.

    1997-11-01

    A Hardinge CNC lathe has been fitted with sensors and a data acquisition system for the measurement, processing and storage of accelerations and forces associated with orthogonal cutting. This system has been completely validated. Orthogonal cutting experiments were designed in order to study the effects of critical cutting parameters on machining dynamics. Three major experimental sets were conducted. In the first set the depth of cut was increased in a stepwise fashion, while the workpiece surface speed, the spindle speed, and the tool feedrate were maintained invariant. In the second and third sets, the spindle speed and feedrate were varied, respectively, while maintaining all the other parameters invariant. In total over two hundred orthogonal cutting experiments were performed. In each experiment, the two non-zero components of the tool acceleration and the two non-zero components of the cutting force were measured. Despite high noise levels, mutual information calculations with smoothing kernels and false nearest neighbor algorithms proved to be sufficiently robust to provide upper bounds on attractor dimension for all fifty data sets studied. These results prove that the infinite dimensional cutting process has an associated attractor of dimension {le} 4. This result is important as a guide to model construction. An analysis of the power spectral sideband structure proved that sideband spacing is identical to the turning frequency. This result was further substantiated through envelope detection techniques. A linear delay model was shown to emulate the experimental power spectrum and possess predictive capacity.

  3. Intermetallic blades for fabric cutting. CRADA final report

    SciTech Connect

    Sikka, V.K.; Blue, C.A.; Sklad, S.; Shih, H.R.; Off, J.W.A.

    1998-08-01

    This report describes the evaluation of nickel- and iron-aluminide blades for cutting fabric as opposed to conventional steel blades. The aluminides were selected as blade material because of their extremely high work-hardening rate and the possibility of forming aluminum oxide on the surface to further enhance the wear resistance. Unlike steel blades, they do not require heat treating to become strong. A testing facility using an Eastman cutter was designed and built at the Oak Ridge National Laboratory (ORNL) for testing of blades. Denim fabric supplied by Levi Strauss was used. For lack of sufficient fabric, heavy paper was also used. Extensive testing revealed that there were several issues in getting the true comparison between various blades. The most important issue was the consistent sharpening of the blade edge. With all of the effort and precautions, identical edges could not be put on the blades of all the different materials. The second issue was the limited availability of fabric to evaluate the end-of-life limit for the blade edges. Two nickel- and three iron-aluminide compositions were evaluated. Under test conditions, the iron-aluminide alloy (PM-60), based on FeAl, was found to outperform other aluminides and the steel blade. Based on the data presented in this report, the authors recommend that additional testing be carried out on both the steel and aluminide blades to determine the number of times each blade can be sharpened prior to its replacement. However, the recommended testing needs to be conducted on blades for which the identical cutting edges and sharpening are incorporated. They further recommend that if the iron-aluminide blade is truly superior, a cost analysis be performed to determine its commercial feasibility. The best aluminide blades should be tested by commercial textile companies.

  4. The Abscission Checkpoint: Making It to the Final Cut.

    PubMed

    Nähse, Viola; Christ, Liliane; Stenmark, Harald; Campsteijn, Coen

    2017-01-01

    Cytokinesis is the final stage of cell division and is concluded by abscission of the intercellular bridge to physically separate the daughter cells. Timing of cytokinetic abscission is monitored by a molecular machinery termed the abscission checkpoint. This machinery delays abscission in cells with persistent chromatin in the intercellular bridge. Recent work has also uncovered its response to high membrane tension, nuclear pore defects, and DNA replication stress. Although it is known that the abscission checkpoint depends on persistent activity of the Aurora B protein kinase, we have only recently begun to understand its molecular basis. We propose here a molecular framework for abscission checkpoint signaling and we discuss outstanding questions relating to its function and physiological relevance.

  5. ESA's Venus Express to reach final destination

    NASA Astrophysics Data System (ADS)

    2006-04-01

    First step: catching Venus To begin to explore our Earth’s hot and hazy sister planet, Venus Express must complete a critical first step, the most challenging one following launch. This involves a set of complex operations and manoeuvres that will inject the spacecraft into orbit. The Venus Orbit Insertion (VOI) manoeuvre allows the spacecraft to reduce its speed relative to Venus, so that it can be captured by the planet’s gravitation. The manoeuvre is a critical one which must proceed at precisely the right place and time. The VOI phase officially started on 4 April and will not be completed until 13 April. It is split into three main sub-phases. The first consists in preparing or initialising the spacecraft for the actual capture manoeuvre so as to avoid the risk of the spacecraft going into safe mode, should parameters unrelated to VOI go off-range. The capture manoeuvre itself consists of a main-engine burn lasting about 50 minutes on the morning of 11 April starting at 09:17 (Central European Summer Time). This is the second main VOI sub-phase. The final sub-phase will be restoring all spacecraft functions, notably resuming communications with Earth and uplinking the commands to be executed during the preliminary ‘capture’ orbit. Orbital capture is controlled by an automatic sequence of predefined commands, uploaded to the spacecraft four days prior to VOI. This sequence is the minimum set needed to perform the main-engine burn. All spacecraft operations are controlled and commanded by the ground control team located at ESA’s European Spacecraft Operations Centre (ESOC) in Darmstadt, Germany. Timeeline of major VOI events (some times subject to change) 4 Aprilacecraft transmitter connected to low gain antenna is switched on. During its interplanetary cruise and during the scientific part of the mission to come, Venus Express communicates with Earth by means of its two high gain antennas. However, during the orbit capture phase (11 April), these two

  6. Community Background Reports: Cut Bank, Montana. National Study of American Indian Education, Series I, No. 8, Final Report.

    ERIC Educational Resources Information Center

    Humphrey, Theodore

    As a part of the Final Report of the National Study of American Indian Education, this paper is a report on the community of Cut Bank, Montana. Data were collected in the fall of 1968, when a 4-member team from the University of Colorado made a 6-week study at the Blackfeet Indian Reservation. General factors studied were location, physical…

  7. 75 FR 8301 - Certain Cut-to-Length Carbon Steel Plate From the People's Republic of China: Final Results of...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-02-24

    ... of China: Final Results of the 2007-2008 Administrative Review of the Antidumping Duty Order AGENCY... From the People's Republic of China: Preliminary Results and Partial Rescission of Antidumping Duty... review of certain cut- to-length carbon steel plate (``CTL plate'') from the People's Republic of China...

  8. 77 FR 73616 - Certain Cut-to-Length Carbon Steel Plate From the People's Republic of China: Final Results of...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-12-11

    ... Cut-to-Length Carbon Steel Plate From the People's Republic of China: Final Results of Antidumping... plate'') from the People's Republic of China (``PRC'') covering the period of review (``POR'') November... Republic of China: Preliminary Results of Antidumping Administrative Review and Preliminary Determination...

  9. Financial aspects of partial cutting practices in central Appalachian hardwoods. Forest Service research paper (Final)

    SciTech Connect

    Miller, G.W.

    1993-06-01

    Unveven-aged silvicultural practices can be used to regenerate and manage many eastern hardwood stands. Single-tree selection methods are feasible in stands where a desirable shade-tolerant commercial species can be regenerated following periodic harvests. A variety of partial cutting practices, including single-tree selection and diameter-limit cutting have been used for 30 years or more to manage central Appalachian hardwoods on the Fernow Experimental Forest near Parsons, West Virginia. Results from these research areas are presented to help forest managers evaluate financial aspects of partial cutting practices. Observed volume growth, product yields, changes in species composition, and changes in residual stand quality are used to evaluate potential financial returns. Also, practical economic considerations for applying partial cutting methods are discussed.

  10. Gene expression profiling during adventitious root formation in carnation stem cuttings.

    PubMed

    Villacorta-Martín, Carlos; Sánchez-García, Ana Belén; Villanova, Joan; Cano, Antonio; van de Rhee, Miranda; de Haan, Jorn; Acosta, Manuel; Passarinho, Paul; Pérez-Pérez, José Manuel

    2015-10-14

    Adventitious root (AR) formation is a critical step in vegetative propagation of most ornamental plants, such as carnation. AR formation from stem cuttings is usually divided into several stages according to physiological and metabolic markers. Auxin is often applied exogenously to promote the development of ARs on stem cuttings of difficult-to-root genotypes. By whole transcriptome sequencing, we identified the genes involved in AR formation in carnation cuttings and in response to exogenous auxin. Their expression profiles have been analysed through RNA-Seq during a time-course experiment in the stem cutting base of two cultivars with contrasting efficiencies of AR formation. We explored the kinetics of root primordia formation in these two cultivars and in response to exogenously-applied auxin through detailed histological and physiological analyses. Our results provide, for the first time, a number of molecular, histological and physiological markers that characterize the different stages of AR formation in this species and that could be used to monitor adventitious rooting on a wide collection of carnation germplasm with the aim to identify the best-rooting cultivars for breeding purposes.

  11. Characterization and Comparative Expression Profiling of Browning Response in Medinilla formosana after Cutting

    PubMed Central

    Wang, Yan; Wang, Yiting; Li, Kunfeng; Song, Xijiao; Chen, Jianping

    2016-01-01

    Plant browning is a recalcitrant problem for in vitro culture and often leads to poor growth of explants and even failure of tissue culture. However, the molecular mechanisms underlying browning-induced physiological processes remain unclear. Medinilla is considered one of the most difficult genera for tissue culture owning to its severe browning. In the present study, intact aseptic plantlets of Medinilla formosana Hayata previously obtained by ovary culture, were used to explore the characteristics and molecular mechanism of the browning response. Successive morphological and anatomical observations after cutting showed that the browning of M. formosana was not lethal but adaptive. De novo transcriptome and digital gene expression (DGE) profiling using Illumina high-throughput sequencing were then used to explore molecular regulation after cutting. About 7.5 million tags of de novo transcriptome were obtained and 58,073 unigenes were assembled and annotated. A total of 6,431 differentially expressed genes (DEGs) at three stages after cutting were identified, and the expression patterns of these browning-related genes were clustered and analyzed. A number of putative DEGs involved in signal transduction and secondary metabolism were particularly studied and the potential roles of these cutting-responsive mRNAs in plant defense to diverse abiotic stresses are discussed. The DGE profiling data were also validated by quantitative RT-PCR analysis. The data obtained in this study provide an excellent resource for unraveling the molecular mechanisms of browning processes during in vitro tissue culture, and lay a foundation for future studies to inhibit and eliminate browning damage. PMID:28066460

  12. Characterization and Comparative Expression Profiling of Browning Response in Medinilla formosana after Cutting.

    PubMed

    Wang, Yan; Wang, Yiting; Li, Kunfeng; Song, Xijiao; Chen, Jianping

    2016-01-01

    Plant browning is a recalcitrant problem for in vitro culture and often leads to poor growth of explants and even failure of tissue culture. However, the molecular mechanisms underlying browning-induced physiological processes remain unclear. Medinilla is considered one of the most difficult genera for tissue culture owning to its severe browning. In the present study, intact aseptic plantlets of Medinilla formosana Hayata previously obtained by ovary culture, were used to explore the characteristics and molecular mechanism of the browning response. Successive morphological and anatomical observations after cutting showed that the browning of M. formosana was not lethal but adaptive. De novo transcriptome and digital gene expression (DGE) profiling using Illumina high-throughput sequencing were then used to explore molecular regulation after cutting. About 7.5 million tags of de novo transcriptome were obtained and 58,073 unigenes were assembled and annotated. A total of 6,431 differentially expressed genes (DEGs) at three stages after cutting were identified, and the expression patterns of these browning-related genes were clustered and analyzed. A number of putative DEGs involved in signal transduction and secondary metabolism were particularly studied and the potential roles of these cutting-responsive mRNAs in plant defense to diverse abiotic stresses are discussed. The DGE profiling data were also validated by quantitative RT-PCR analysis. The data obtained in this study provide an excellent resource for unraveling the molecular mechanisms of browning processes during in vitro tissue culture, and lay a foundation for future studies to inhibit and eliminate browning damage.

  13. Gene expression analysis of precision-cut human liver slices indicates stable expression of ADME-Tox related genes

    SciTech Connect

    Elferink, M.G.L.; Olinga, P.; van Leeuwen, E.M.; Bauerschmidt, S.; Polman, J.; Schoonen, W.G.; Heisterkamp, S.H.; Groothuis, G.M.M.

    2011-05-15

    In the process of drug development it is of high importance to test the safety of new drugs with predictive value for human toxicity. A promising approach of toxicity testing is based on shifts in gene expression profiling of the liver. Toxicity screening based on animal liver cells cannot be directly extrapolated to humans due to species differences. The aim of this study was to evaluate precision-cut human liver slices as in vitro method for the prediction of human specific toxicity by toxicogenomics. The liver slices contain all cell types of the liver in their natural architecture. This is important since drug-induced toxicity often is a multi-cellular process. Previously we showed that toxicogenomic analysis of rat liver slices is highly predictive for rat in vivo toxicity. In this study we investigated the levels of gene expression during incubation up to 24 h with Affymetrix microarray technology. The analysis was focused on a broad spectrum of genes related to stress and toxicity, and on genes encoding for phase-I, -II and -III metabolizing enzymes and transporters. Observed changes in gene expression were associated with cytoskeleton remodeling, extracellular matrix and cell adhesion, but for the ADME-Tox related genes only minor changes were observed. PCA analysis showed that changes in gene expression were not associated with age, sex or source of the human livers. Slices treated with acetaminophen showed patterns of gene expression related to its toxicity. These results indicate that precision-cut human liver slices are relatively stable during 24 h of incubation and represent a valuable model for human in vitro hepatotoxicity testing despite the human inter-individual variability.

  14. AXIS: Adult Education eXpress Intercommunication Support. Final Report.

    ERIC Educational Resources Information Center

    Reiff, Tana

    This package includes the final report and selected products of the Adult education eXpress Intercommunication Support (AXIS) project, which was conducted to facilitate communication related to professional development services administered by the Pennsylvania Department of Education's Bureau of Adult Basic and Literacy Education (ABLE) and…

  15. 78 FR 29113 - Certain Cut-to-Length Carbon-Quality Steel Plate Products From the Republic of Korea: Final...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-05-17

    ... International Trade Administration Certain Cut-to-Length Carbon-Quality Steel Plate Products From the Republic... order on certain cut-to-length carbon-quality steel plate products from the Republic of Korea. For these... preliminary results of the administrative review of the antidumping duty order on certain cut-to-length...

  16. 75 FR 29976 - Certain Cut-to-Length Carbon-Quality Steel Plate Products From Italy: Extension of the Final...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-05-28

    ... International Trade Administration Certain Cut-to-Length Carbon-Quality Steel Plate Products From Italy... antidumping duty order on certain cut-to-length carbon-quality steel plate products from Italy. See Certain Cut-to-Length Carbon-Quality Steel Plate Products From Italy: Preliminary Results of Antidumping...

  17. Cutting concrete with abrasive waterjets. Phase 1: evaluation of relatively low pressure water-jet performance. Final report

    SciTech Connect

    Yie, G.G.

    1986-01-01

    In laboratory testing, a prototype low-pressure abrasive water-jet system proved more effective in cutting concrete and asphalt than the high-pressure systems tested before. Projected operating costs for the hand-carried unit - a fraction of those of conventional concrete saws and carbide cutting wheels - could mean savings between $15,000 and $20,000 per mile of cut.

  18. 78 FR 67334 - Suspension Agreement on Certain Cut-to-Length Carbon Steel Plate From Ukraine; Final Results of...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-11-12

    ... covering Metinvest Holding LLC (Metinvest) and its affiliated companies Azovstal Iron & Steel Works (Azovstal) and Ilyich Iron and Steel Works (Ilyich). See Suspension Agreement on Certain Cut-to-Length...

  19. Development of a water-jet concrete-cutting system. Volume 3. System equipment and testing. Final report

    SciTech Connect

    McDonald, M.C.; Reichman, J.M.; Hashish, M.

    1984-09-01

    A high-pressure, abrasive water-jet system that removes road-grade pavement offers utilities a financially attractive way of reducing the installation costs of underground cables. This system, mounted on a vehicular power supply and street tested, demonstrated that it can economically and quietly achieve cutting depths of up to 8 in.

  20. Efficacy of sweet whey containing final dips in reducing protein oxidation in retail-cut cubed beefsteak

    USDA-ARS?s Scientific Manuscript database

    Oxidative degradation results in extensive deterioration of shelf-life and quality of retail-cut muscle foods. Use of antioxidants, especially the ones of natural origin, can markedly reduce this process without adverse health consequences to the consumer. Sweet whey originating from Cheddar (CW) an...

  1. The impact of PPARα activation on whole genome gene expression in human precision cut liver slices.

    PubMed

    Janssen, Aafke W F; Betzel, Bark; Stoopen, Geert; Berends, Frits J; Janssen, Ignace M; Peijnenburg, Ad A; Kersten, Sander

    2015-10-08

    Studies in mice have shown that PPARα is an important regulator of lipid metabolism in liver and key transcription factor involved in the adaptive response to fasting. However, much less is known about the role of PPARα in human liver. Here we set out to study the function of PPARα in human liver via analysis of whole genome gene regulation in human liver slices treated with the PPARα agonist Wy14643. Quantitative PCR indicated that PPARα is well expressed in human liver and human liver slices and that the classical PPARα targets PLIN2, VLDLR, ANGPTL4, CPT1A and PDK4 are robustly induced by PPARα activation. Transcriptomics analysis indicated that 617 genes were upregulated and 665 genes were downregulated by PPARα activation (q value < 0.05). Many genes induced by PPARα activation were involved in lipid metabolism (ACSL5, AGPAT9, FADS1, SLC27A4), xenobiotic metabolism (POR, ABCC2, CYP3A5) or the unfolded protein response, whereas most of the downregulated genes were involved in immune-related pathways. Among the most highly repressed genes upon PPARα activation were several chemokines (e.g. CXCL9-11, CCL8, CX3CL1, CXCL6), interferon γ-induced genes (e.g. IFITM1, IFIT1, IFIT2, IFIT3) and numerous other immune-related genes (e.g. TLR3, NOS2, and LCN2). Comparative analysis of gene regulation by Wy14643 between human liver slices and primary human hepatocytes showed that down-regulation of gene expression by PPARα is much better captured by liver slices as compared to primary hepatocytes. In particular, PPARα activation markedly suppressed immunity/inflammation-related genes in human liver slices but not in primary hepatocytes. Finally, several putative new target genes of PPARα were identified that were commonly induced by PPARα activation in the two human liver model systems, including TSKU, RHOF, CA12 and VSIG10L. Our paper demonstrates the suitability and superiority of human liver slices over primary hepatocytes for studying the functional

  2. Gene expression profiling in juvenile and mature cuttings of Eucalyptus grandis reveals the importance of microtubule remodeling during adventitious root formation.

    PubMed

    Abu-Abied, Mohamad; Szwerdszarf, David; Mordehaev, Inna; Yaniv, Yossi; Levinkron, Saar; Rubinstein, Mor; Riov, Joseph; Ophir, Ron; Sadot, Einat

    2014-09-30

    The ability to form adventitious roots (AR) is an economically important trait that is lost during the juvenile-to-mature phase change in woody plants. Auxin treatment, which generally promotes rooting in juvenile cuttings, is often ineffective when applied to mature cuttings. The molecular basis for this phenomenon in Eucalyptus grandis was addressed here. A comprehensive microarray analysis was performed in order to compare gene-expression profiles in juvenile and mature cuttings of E. grandis, with or without auxin treatment on days, 0, 1, 3, 6, 9 and 12 post AR induction. Under these conditions AR primordia were formed only in auxin-treated juvenile cuttings. However, clustering the expression profiles revealed that the time after induction contributed more significantly to the differences in expression than the developmental phase of the cuttings or auxin treatment. Most detected differences which were related to the developmental phase and auxin treatment occurred on day 6, which correlated with the kinetics of AR-primordia formation. Among the functional groups of transcripts that differed between juvenile and mature cuttings was that of microtubules (MT). The expression of 42 transcripts annotated as coding for tubulin, MT-associated proteins and kinesin motor proteins was validated in the same RNA samples. The results suggest a coordinated developmental and auxin dependent regulation of several MT-related transcripts in these cuttings. To determine the relevance of MT remodeling to AR formation, MTs were subjected to subtle perturbations by trifluralin, a MT disrupting drug, applied during auxin induction. Juvenile cuttings were not affected by the treatment, but rooting of mature cuttings increased from 10 to more than 40 percent. The data suggest that juvenile-specific MT remodeling is involved in AR formation in E. grandis.

  3. 76 FR 50996 - Affirmative Final Determination of Circumvention of the Antidumping Duty Order on Certain Cut-to...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-08-17

    ... International Trade Administration Affirmative Final Determination of Circumvention of the Antidumping Duty... Administration, International Trade Administration, Department of Commerce. SUMMARY: On April 23, 2010, the... Bezirganian or Robert James, AD/ CVD Operations, Office 7, Import Administration, International...

  4. Cutting Edge: Resident Memory CD8 T Cells Express High-Affinity TCRs.

    PubMed

    Frost, Elizabeth L; Kersh, Anna E; Evavold, Brian D; Lukacher, Aron E

    2015-10-15

    Tissue-resident memory T (TRM) cells serve as vanguards of antimicrobial host defense in nonlymphoid tissues, particularly at barrier epithelia and in organs with nonrenewable cell types (e.g., brain). In this study, we asked whether an augmented ability to sense Ag complemented their role as early alarms of pathogen invasion. Using mouse polyomavirus, we show that brain-resident mouse polyomavirus-specific CD8 T cells, unlike memory cells in the spleen, progressively increase binding to MHC class I tetramers and CD8 coreceptor expression. Using the two-dimensional micropipette adhesion-frequency assay, we show that TRM cells in brain, as well as in kidney, express TCRs with up to 20-fold higher affinity than do splenic memory T cells, whereas effector cells express TCRs of similar high affinity in all organs. Together, these data demonstrate that TRM cells retain high TCR affinity, which endows them with the high Ag sensitivity needed for front-line defense against infectious agents. Copyright © 2015 by The American Association of Immunologists, Inc.

  5. Cutting edge: adenovirus E19 has two mechanisms for affecting class I MHC expression.

    PubMed

    Bennett, E M; Bennink, J R; Yewdell, J W; Brodsky, F M

    1999-05-01

    Viral strategies for immune evasion include inhibition of various steps in the class I MHC assembly pathway. Here, we demonstrate that adenovirus produces one gene product with a dual function in this regard. It is well established that adenovirus E19 binds class I molecules and retains them in the endoplasmic reticulum (ER). However, E19 also delays the expression of class I alleles to which it cannot tightly bind. Here, we show that E19 binds TAP and acts as a tapasin inhibitor, preventing class I/TAP association. DeltaE19, an E19 mutant lacking the ER-retention signal, delays maturation of class I molecules, indicating that E19's inhibition of class I/TAP interaction is sufficient to delay class I expression. These data identify tapasin inhibition as a novel mechanism of viral immune evasion and suggest that, through this secondary mechanism, adenovirus can affect Ag presentation by MHC alleles that it can only weakly affect by direct retention.

  6. Caste-Specific Expression Patterns of Immune Response and Chemosensory Related Genes in the Leaf-Cutting Ant, Atta vollenweideri

    PubMed Central

    Koch, Sarah I.; Groh, Katrin; Vogel, Heiko; Hannson, Bill S.; Kleineidam, Christoph J.; Grosse-Wilde, Ewald

    2013-01-01

    Leaf-cutting ants are evolutionary derived social insects with elaborated division of labor and tremendous colony sizes with millions of workers. Their social organization is mainly based on olfactory communication using different pheromones and is promoted by a pronounced size-polymorphism of workers that perform different tasks within the colony. The size polymorphism and associated behaviors are correlated to distinct antennal lobe (AL) phenotypes. Two worker phenotypes differ in number of olfactory glomeruli in the AL and the presence or absence of an extremely large glomerulus (macroglomerulus), involved in trail-pheromone reception. The males' AL contains three macroglomeruli which are presumably involved in detection of sex-pheromone components. We investigated the antennal transcriptome data of all major castes (males, queens and workers) and two worker subcastes (large and tiny workers). In order to identify putative odorant receptor genes involved in pheromone detection, we identified differentially expressed odorant receptor genes (OR-genes) using custom microarrays. In total, we found 185 OR-gene fragments that are clearly related to ORs and we identified orthologs for 70 OR-genes. Among them one OR-gene differs in relative expression between the two worker subcastes by a factor of >3 and thus is a very promising candidate gene for the trail-pheromone receptor. Using the relative expression of OR-genes in males versus queens, we identified 2 candidates for sex-pheromone receptor genes in males. In addition, we identified genes from all other chemosensory related gene families (13 chemosensory protein genes, 8 odorant binding protein genes, 2 sensory-neuron membrane protein genes, 7 ionotropic receptor genes, 2 gustatory receptor genes), and we found ant-specific expansions in the chemosensory protein gene family. In addition, a large number of genes involved in immune defense exhibited differential expression across the three different castes, and some

  7. Cutting Edge: Innate Immune Augmenting Vesicular Stomatitis Virus Expressing Zika Virus Proteins Confers Protective Immunity.

    PubMed

    Betancourt, Dillon; de Queiroz, Nina M G P; Xia, Tianli; Ahn, Jeonghyun; Barber, Glen N

    2017-04-15

    Zika virus (ZIKV) has become a serious public health concern because of its link to brain damage in developing human fetuses. Recombinant vesicular stomatitis virus (rVSV) was shown to be a highly effective and safe vector for the delivery of foreign immunogens for vaccine purposes. In this study, we generated rVSVs (wild-type and attenuated VSV with mutated matrix protein [VSVm] versions) that express either the full length ZIKV envelope protein (ZENV) alone or include the ZENV precursor to the membrane protein upstream of the envelope protein, and our rVSV-ZIKV constructs showed efficient immunogenicity in murine models. We also demonstrated maternal protective immunity in challenged newborn mice born to female mice vaccinated with VSVm-ZENV containing the transmembrane domain. Our data indicate that rVSVm may be a suitable strategy for the design of effective vaccines against ZIKV.

  8. Caste-specific expression of genetic variation in the size of antibiotic-producing glands of leaf-cutting ants.

    PubMed

    Hughes, W O H; Bot, A N M; Boomsma, J J

    2010-02-22

    Social insect castes represent some of the most spectacular examples of phenotypic plasticity, with each caste being associated with different environmental conditions during their life. Here we examine the level of genetic variation in different castes of two polyandrous species of Acromyrmex leaf-cutting ant for the antibiotic-producing metapleural gland, which has a major role in defence against parasites. Gland size increases allometrically. The small workers that play the main role in disease defence have relatively large glands compared with larger workers, while the glands of gynes are substantially larger than those of any workers, for their body size. The gland size of large workers varies significantly between patrilines in both Acromyrmex echinatior and Acromyrmex octospinosus. We also examined small workers and gynes in A. echinatior, again finding genetic variation in gland size in these castes. There were significant positive relationships between the gland sizes of patrilines in the different castes, indicating that the genetic mechanism underpinning the patriline variation has remained similar across phenotypes. The level of expressed genetic variation decreased from small workers to large workers to gynes. This is consistent with the hypothesis that there is individual selection on disease defence in founding queens and colony-level selection on disease defence in the worker castes.

  9. Differential equations on unitarity cut surfaces

    NASA Astrophysics Data System (ADS)

    Zeng, Mao

    2017-06-01

    We reformulate differential equations (DEs) for Feynman integrals to avoid doubled propagators in intermediate steps. External momentum derivatives are dressed with loop momentum derivatives to form tangent vectors to unitarity cut surfaces, in a way inspired by unitarity-compatible IBP reduction. For the one-loop box, our method directly produces the final DEs without any integration-by-parts reduction. We further illustrate the method by deriving maximal-cut level differential equations for two-loop nonplanar five-point integrals, whose exact expressions are yet unknown. We speed up the computation using finite field techniques and rational function reconstruction.

  10. Application of water jet assisted drag bit and pick cutter for the cutting of coal measure rocks. Final technical report. [Tests of combination in different rocks

    SciTech Connect

    Ropchan, D.; Wang, F.D.; Wolgamott, J.

    1980-04-01

    A laboratory investigation was made of the effects of high pressure water jets on the cutting forces of drag bit cutters in sedimentary rocks. A hard and soft sandstone, shale and limestone were tested with commercially obtainable conical and plow type drag bits on the EMI linear cutting machine. About 1200 cuts were made at different bit penetration, jet orientation, and water pressure to determine the reduction of cutting forces on the bit from the use of the water jet. Both independent and interactive cutting was used. The greatest reduction in cutting forces were with both of the sandstones; the drag forces were reduced about 30 percent and the normal forces about 60 percent at 5000 psi water pressure with the nozzle behind the bit. The method was less effective in the shale, except at 10,000 psi water pressure the reduction in drag force was about 55 percent. Of the rocks tested, the limestone was least affected by the water jet. The cutting forces for the plow bit showed continuous change with wear so a machined conical bit was used for most of the testing. Tests with the plow bit did show a large reduction in cutting forces by using the water jet with worn bits. An economic analysis of equipping a drag bit tunnel boring machine indicated that the water jet system could reduce costs per foot in sandstone by up to 40 percent.

  11. Laser Cutting

    DTIC Science & Technology

    1988-06-01

    lasers that are optically modified to produce high beam quality at reduced power levels for precision drilling and trepanning. * Nd:YAG lasers with...a smooth, dross-free cut face while the marking consists of a series of precisely placed shallow pits where surface finish and dross are not usually...neodymium:yttrium-aluminum-garnet (Nd:YAG) pulsed cutting data because the technique is considered vital in meeting the detailed precision cutting

  12. Bone cutting.

    PubMed

    Giraud, J Y; Villemin, S; Darmana, R; Cahuzac, J P; Autefage, A; Morucci, J P

    1991-02-01

    Bone cutting has always been a problem for surgeons because bone is a hard living material, and many osteotomes are still very crude tools. Technical improvement of these surgical tools has first been their motorization. Studies of the bone cutting process have indicated better features for conventional tools. Several non-conventional osteotomes, particularly ultrasonic osteotomes are described. Some studies on the possible use of lasers for bone cutting are also reported. Use of a pressurised water jet is also briefly examined. Despite their advantages, non-conventional tools still require improvement if they are to be used by surgeons.

  13. Cutting assembly

    DOEpatents

    Racki, Daniel J.; Swenson, Clark E.; Bencloski, William A.; Wineman, Arthur L.

    1984-01-01

    A cutting apparatus includes a support table mounted for movement toward and away from a workpiece and carrying a mirror which directs a cutting laser beam onto the workpiece. A carrier is rotatably and pivotally mounted on the support table between the mirror and workpiece and supports a conduit discharging gas toward the point of impingement of the laser beam on the workpiece. Means are provided for rotating the carrier relative to the support table to place the gas discharging conduit in the proper positions for cuts made in different directions on the workpiece.

  14. Improvement Cut

    Treesearch

    J. W. Johnson

    1950-01-01

    Early, effects of partial cutting on diameter growth in bottomland hardwood forests have been measured recently near Vance, Mississippi, according to a report by J. W. Johnson of the Southern Forest Experiment Station, New Orleans, LA.

  15. Cutting Candles

    ERIC Educational Resources Information Center

    Ranucci, Ernest R.

    1973-01-01

    Different regular-polygon-shaped candles wound with a sheet of paper are cut through obliquely. When the papers are unwound, unique patterns are revealed. Investigation of these patterns leads to the discovery of geometric concepts. (JP)

  16. Induction of Expression of Genes Coding for Sporamin and β-Amylase by Polygalacturonic Acid in Leaf-Petiole Cuttings of Sweet Potato 1

    PubMed Central

    Ohto, Masa-aki; Nakamura-Kito, Kyoko; Nakamura, Kenzo

    1992-01-01

    Sporamin and β-amylase are two major proteins of tuberous storage root of sweet potato (Ipomoea batatas) and their accumulation can be induced concomitantly with the accumulation of starch in leaves and petioles by sucrose (K Nakamura, M Ohto, N Yoshida, K Nakamura [1991] Plant Physiol 96: 902-909). Although mechanical wounding of leaves of sweet potato only occasionally induced the expression of sporamin and β-amylase genes, their expression could be reproducibly induced in leaf-petiole cuttings when these explants were dipped in a solution of polygalacturonic acid or chitosan at their cut edges. Polygalacturonic acid seemed to induce expression of the same genes coding for sporamin and β-amylase that are induced by sucrose. Because polygalacturonic acid and chitosan are known to mediate the induction of wound-inducible defense reactions, these results raise an interesting possibility that β-amylase, in addition to sporamin, may have some role in the defense reaction. Expression of sporamin and β-amylase genes could also be induced by abscisic acid, and this induction by abscisic acid, as well as induction by polygalacturonic acid or sucrose, was repressed by gibberellic acid. By contrast, methyl jasmonate did not cause the significant induction of either sporamin or β-amylase mRNAs. Induction of expression of sporamin and β-amylase genes by polygalacturonic acid or sucrose was inhibited by cycloheximide, suggesting that de novo synthesis of proteins is required for both of the induction processes. ImagesFigure 1Figure 2Figure 3Figure 4Figure 5 PMID:16668901

  17. A specific group of genes respond to cold dehydration stress in cut Alstroemeria flowers whereas ambient dehydration stress accelerates developmental senescence expression patterns

    PubMed Central

    Wagstaff, Carol; Bramke, Irene; Breeze, Emily; Thornber, Sarah; Harrison, Elizabeth; Thomas, Brian; Buchanan-Wollaston, Vicky; Stead, Tony; Rogers, Hilary

    2010-01-01

    Petal development and senescence entails a normally irreversible process. It starts with petal expansion and pigment production, and ends with nutrient remobilization and ultimately cell death. In many species this is accompanied by petal abscission. Post-harvest stress is an important factor in limiting petal longevity in cut flowers and accelerates some of the processes of senescence such as petal wilting and abscission. However, some of the effects of moderate stress in young flowers are reversible with appropriate treatments. Transcriptomic studies have shown that distinct gene sets are expressed during petal development and senescence. Despite this, the overlap in gene expression between developmental and stress-induced senescence in petals has not been fully investigated in any species. Here a custom-made cDNA microarray from Alstroemeria petals was used to investigate the overlap in gene expression between developmental changes (bud to first sign of senescence) and typical post-harvest stress treatments. Young flowers were stressed by cold or ambient temperatures without water followed by a recovery and rehydration period. Stressed flowers were still at the bud stage after stress treatments. Microarray analysis showed that ambient dehydration stress accelerates many of the changes in gene expression patterns that would normally occur during developmental senescence. However, a higher proportion of gene expression changes in response to cold stress were specific to this stimulus and not senescence related. The expression of 21 transcription factors was characterized, showing that overlapping sets of regulatory genes are activated during developmental senescence and by different stresses. PMID:20457576

  18. A specific group of genes respond to cold dehydration stress in cut Alstroemeria flowers whereas ambient dehydration stress accelerates developmental senescence expression patterns.

    PubMed

    Wagstaff, Carol; Bramke, Irene; Breeze, Emily; Thornber, Sarah; Harrison, Elizabeth; Thomas, Brian; Buchanan-Wollaston, Vicky; Stead, Tony; Rogers, Hilary

    2010-06-01

    Petal development and senescence entails a normally irreversible process. It starts with petal expansion and pigment production, and ends with nutrient remobilization and ultimately cell death. In many species this is accompanied by petal abscission. Post-harvest stress is an important factor in limiting petal longevity in cut flowers and accelerates some of the processes of senescence such as petal wilting and abscission. However, some of the effects of moderate stress in young flowers are reversible with appropriate treatments. Transcriptomic studies have shown that distinct gene sets are expressed during petal development and senescence. Despite this, the overlap in gene expression between developmental and stress-induced senescence in petals has not been fully investigated in any species. Here a custom-made cDNA microarray from Alstroemeria petals was used to investigate the overlap in gene expression between developmental changes (bud to first sign of senescence) and typical post-harvest stress treatments. Young flowers were stressed by cold or ambient temperatures without water followed by a recovery and rehydration period. Stressed flowers were still at the bud stage after stress treatments. Microarray analysis showed that ambient dehydration stress accelerates many of the changes in gene expression patterns that would normally occur during developmental senescence. However, a higher proportion of gene expression changes in response to cold stress were specific to this stimulus and not senescence related. The expression of 21 transcription factors was characterized, showing that overlapping sets of regulatory genes are activated during developmental senescence and by different stresses.

  19. Differential protein expression in Spirometra erinacei according to its development in its final host.

    PubMed

    Kim, Jae-Hwan; Kim, Young Ju; Sohn, Woon-Mok; Bae, Young Mee; Hong, Sung-Tae; Choi, Min-Ho

    2009-11-01

    This study was undertaken to identify genes involved in the growth and development of Spirometra erinacei larvae, an intestinal tapeworm of cats and dogs, within the final host. The differential protein expression at three different stages of S. erinacei, the plerocercoid larvae, 8-day-old juveniles, and adults, was compared using two-dimensional electrophoresis. Specifically or highly expressed proteins in juvenile worms were analyzed by matrix-assisted laser desorption/ionization time-of-flight mass spectrometer (MS)/MS. The proteome map of larvae showed fewer protein spots than juveniles or adults, whereas juveniles or adults revealed a similar protein expression profile. Eight juvenile-specific and five upregulated proteins of juveniles were identified and matched to proteins of known biological functions. These were grouped into several categories of functionally related proteins: DNA/RNA metabolism, cell trafficking, cytoskeleton, protein processing and degradation, energy metabolism, and oxidative stress. Our results give an overview of the growth and development mechanisms of cestodes within the final host and extend our understanding of parasite biology in the host-parasite relationship.

  20. Hair cut

    NASA Image and Video Library

    2012-11-10

    ISS033-E-018986 (10 Nov. 2012) --- Russian cosmonaut Evgeny Tarelkin, Expedition 33 flight engineer, trims the hair of Russian cosmonaut Oleg Novitskiy, flight engineer, in the Tranquility node of the International Space Station. Tarelkin used hair clippers fashioned with a vacuum device to garner freshly cut hair. NASA astronaut Kevin Ford, flight engineer, is visible in the background.

  1. Hair cut

    NASA Image and Video Library

    2012-11-10

    ISS033-E-018991 (10 Nov. 2012) --- Russian cosmonaut Oleg Novitskiy, Expedition 33 flight engineer, trims the hair of Russian cosmonaut Evgeny Tarelkin, flight engineer, in the Tranquility node of the International Space Station. Novitskiy used hair clippers fashioned with a vacuum device to garner freshly cut hair.

  2. The fungal symbiont of Acromyrmex leaf-cutting ants expresses the full spectrum of genes to degrade cellulose and other plant cell wall polysaccharides.

    PubMed

    Grell, Morten N; Linde, Tore; Nygaard, Sanne; Nielsen, Kåre L; Boomsma, Jacobus J; Lange, Lene

    2013-12-28

    The fungus gardens of leaf-cutting ants are natural biomass conversion systems that turn fresh plant forage into fungal biomass to feed the farming ants. However, the decomposition potential of the symbiont Leucocoprinus gongylophorus for processing polysaccharides has remained controversial. We therefore used quantifiable DeepSAGE technology to obtain mRNA expression patterns of genes coding for secreted enzymes from top, middle, and bottom sections of a laboratory fungus-garden of Acromyrmex echinatior leaf-cutting ants. A broad spectrum of biomass-conversion-relevant enzyme genes was found to be expressed in situ: cellulases (GH3, GH5, GH6, GH7, AA9 [formerly GH61]), hemicellulases (GH5, GH10, CE1, GH12, GH74), pectinolytic enzymes (CE8, GH28, GH43, PL1, PL3, PL4), glucoamylase (GH15), α-galactosidase (GH27), and various cutinases, esterases, and lipases. In general, expression of these genes reached maximal values in the bottom section of the garden, particularly for an AA9 lytic polysaccharide monooxygenase and for a GH5 (endocellulase), a GH7 (reducing end-acting cellobiohydrolase), and a GH10 (xylanase), all containing a carbohydrate binding module that specifically binds cellulose (CBM1). Although we did not directly quantify enzyme abundance, the profile of expressed cellulase genes indicates that both hydrolytic and oxidative degradation is taking place. The fungal symbiont of Acromyrmex leaf-cutting ants can degrade a large range of plant polymers, but the conversion of cellulose, hemicellulose, and part of the pectin occurs primarily towards the end of the decomposition process, i.e. in the bottom section of the fungus garden. These conversions are likely to provide nutrients for the fungus itself rather than for the ants, whose colony growth and reproductive success are limited by proteins obtained from ingesting fungal gongylidia. These specialized hyphal tips are hardly produced in the bottom section of fungus gardens, consistent with the ants

  3. Aromatase is expressed and active in the rainbow trout oocyte during final oocyte maturation.

    PubMed

    Gohin, Maella; Bodinier, Pascal; Fostier, Alexis; Chesnel, Franck; Bobe, Julien

    2011-07-01

    While it is generally well accepted that the ovarian follicular sites of estradiol-17β (E2) synthesis are restricted to somatic cells, the possible contribution of the germinal compartment has received little or no attention in teleosts. In order to demonstrate the expression of ovarian aromatase in the oocyte, cyp19a1a mRNA was studied in ovarian follicles by in situ hybridization. In addition, the expression of cyp19a1a was studied in both somatic and germinal compartments of the ovarian follicle in rainbow trout (Oncorhynchus mykiss) during final oocyte maturation (i.e., maturational competence acquisition and subsequent meiosis resumption) by real-time PCR. The enzymatic activity of ovarian aromatase was also studied in both somatic and germinal compartments of the ovarian follicle. Finally, E2 levels were monitored in follicle-enclosed oocytes throughout the pre-ovulatory period. We were able to demonstrate a significant ovarian aromatase expression and activity in the late vitellogenic oocyte. Furthermore, a dramatic decrease in aromatase expression and activity occurs in the oocyte during late oogenesis, concomitantly with the trend observed in surrounding follicular layers. We also report an unexpected increase of E2 levels in the oocyte during the pre-ovulatory period. To our knowledge, these observations are reported for the first time in any teleost species. Together, our data support the hypothesis of the participation of the germinal compartment in follicular estrogen synthesis and a biological role of E2 during oocyte and/or early embryo development.

  4. Examination of a cut-off score to express the meaningful activity of people with dementia using iPad application (ADOC).

    PubMed

    Tomori, Kounosuke; Nagayama, Hirofumi; Saito, Yuki; Ohno, Kanta; Nagatani, Ryutaro; Higashi, Toshio

    2015-03-01

    To determine a quantifiable measure to identify patients with dementia who can choose an illustration of meaningful activity using an iPad application, Aid for Decision-making in Occupation Choice (ADOC). We recruited 116 patients from 5 institutions in Japan. Occupational therapists interviewed patients with dementia to determine meaningful activities using ADOC. The most meaningful activity was confirmed by their primary caregivers. The cut-off was estimated from Mini-Mental State Examination (MMSE). Receiver operating characteristic analysis indicated that an MMSE score of 8 was the cut-off for choosing meaningful activities using ADOC. Sensitivity and specificity was 91.0% and 74.1%, respectively, and the area under the curve value was 0.89. ADOC can provide individualized information regarding meaningful activities for patients with moderate dementia. Implications for Rehabilitation As dementia progresses, difficulty in expressing needs or desires regarding meaningful activity may increase. The iPad application (Aid for Decision-making in Occupation Choice; ADOC) can be useful to promote shared decision-making through a systematic goal-setting process involving a choice of 95 illustrations describing daily activities. Mini-Mental State Examination (MMSE) score greater than 8 points is required to use the ADOC to choose most meaningful activities. ADOC provides individual information regarding meaningful activities for patients with moderate dementia.

  5. How Can I Stop Cutting?

    MedlinePlus

    ... Things to Help You Express the Pain and Deep Emotion Some people cut because the emotions that ... of Use Notice of Nondiscrimination Visit the Nemours Web site. Note: All information on TeensHealth® is for ...

  6. How Can I Stop Cutting?

    MedlinePlus

    ... Things to Help You Express the Pain and Deep Emotion Some people cut because the emotions that ... Privacy Policy & Terms of Use Visit the Nemours Web site. Note: All information on TeensHealth® is for ...

  7. Relationship between Rh-RTH1 and ethylene receptor gene expression in response to ethylene in cut rose.

    PubMed

    Yu, Yixun; Wang, Jing; Wang, Huinan; Zhang, Zhaoqi; Liu, Juanxu

    2010-08-01

    A cDNA clone encoding a putative RTE1-like protein (Rh-RTH1) was obtained from total RNA isolated from senescing rose (Rosa hybrida cv. Tineke) petals using RT-PCR and RACE techniques. The cDNA (1,061 bp) contained an open reading frame of 684 bp corresponding to 227 amino acids. The amino acid sequence had 60.0, 49.6, 61.2, 42.5 and 39.8% identity with that of Arabidopsis RTH, RTE1, tomato GRL2, GRL1 and GR, respectively. Northern hybridization indicated that Rh-RTH1 expression is enhanced by endogenous and exogenous ethylene and inhibited by 1-MCP in petals and gynoecia. Rh-RTH1 expression partly correlated with sites of the ethylene receptor gene Rh-ETR1 and Rh-ETR3 expression, such as the petals, gynoecia, roots, and buds. The induction of Rh-RTH1 and Rh-ETR3 expression was substantially suppressed by 1-MCP treatment, while Rh-ETR1 expression was not reduced by 1-MCP treatment. Following treatment of flowers with sucrose, the level of Rh-RTH1 and Rh-ETR3 mRNA was only slightly decreased in petals and gynoecia. Upon wounding treatment, Rh-RTH1, Rh-ETR1 and Rh-ETR3 showed a quick increase in mRNA accumulation which was positively correlated with the increase in ethylene production. The expression of Rh-RTH1 showed partial correlation with that of Rh-ETR1 and Rh-ETR3.

  8. Rooting of carnation cuttings

    PubMed Central

    Oliveros-Valenzuela, M Rocío; Nicolás, Carlos; Sánchez-Bravo, José

    2009-01-01

    The rooting of stem cuttings is a common vegetative propagation practice in many ornamental species. Among other signals, auxin polarly transported through the stem plays a key role in the formation and growth of adventitious roots. Unlike in other plant species, auxin from mature leaves plays a decisive role in the rooting of carnation (Dianthus caryophyllus. L) cuttings. The gene DcAUX1, which codifies an auxin influx carrier involved in polar auxin transport, has now been cloned and characterized in carnation. The expression pattern of this gene was seen to depend on the organ, the cultivar and the time of cold storage. The variations observed in its expression could be related with the rooting ability of different carnation cultivars. PMID:19721760

  9. First Cut

    NASA Technical Reports Server (NTRS)

    Morring, Frank, Jr.

    2005-01-01

    Lockheed Martin and a Northrop Grumman/Boeing team expect the Crew Exploration Vehicle proposals they submitted last week to change, given the new top-down push at NASA to close the gap between space shuttle retirement and launch of the new crew carrier. Still, delivery of the proposals gives a first glimpse of at least one of the concepts for a space shuttle replacement. Instead of the ballistic capsule approach put forward in some early CEV concept work, Lockheed Martin proposed a lifting body shape with a two-stage thermal protection system, coupled with a cylindrical mission module to give crews of four to six extra room on trips to the Moon, and a trans-Earth injection module (TEIM) for the return powered-at least in the first cut-by a couple of Pratt & Whitney RL10 rocket engines.

  10. Cutting edge: Smad2 and Smad4 regulate TGF-β-mediated Il9 gene expression via EZH2 displacement.

    PubMed

    Wang, Aibo; Pan, Deng; Lee, Young-Hee; Martinez, Gustavo J; Feng, Xin-Hua; Dong, Chen

    2013-11-15

    IL-9 is a proallergic cytokine produced by a newly proposed Th cell subset, Th9. Th9 cells can be generated by treatment of naive T cells with TGF-β and IL-4 in vitro. However, it is still not clear how TGF-β signaling regulates Th9 differentiation. In this study, we demonstrate that Smad2 and Smad4, two transcriptional factors activated by TGF-β signaling, are required for Th9 differentiation in vitro. Deficiency of Smad2 or Smad4 in T cells resulted in impaired IL-9 expression, which was coincident with enrichment of repressive chromatin modification histone H3 K27 trimethylation and enhanced EZH2 binding to the Il9 locus. Pharmacologic inhibition of EZH2 partially rescued IL-9 production in Smad-deficient Th9 cells. Smad proteins may displace EZH2 directly from the Il9 locus, because Smad2 and Smad4 can bind EZH2. Our data shed light on the molecular mechanisms underlying Th9 cell differentiation, revealing that the TGF-β-Smad2/4-signaling pathway regulates IL-9 production through an epigenetic mechanism.

  11. Cutting Edge: B Cell-Intrinsic T-bet Expression Is Required To Control Chronic Viral Infection.

    PubMed

    Barnett, Burton E; Staupe, Ryan P; Odorizzi, Pamela M; Palko, Olesya; Tomov, Vesselin T; Mahan, Alison E; Gunn, Bronwyn; Chen, Diana; Paley, Michael A; Alter, Galit; Reiner, Steven L; Lauer, Georg M; Teijaro, John R; Wherry, E John

    2016-08-15

    The role of Ab and B cells in preventing infection is established. In contrast, the role of B cell responses in containing chronic infections remains poorly understood. IgG2a (IgG1 in humans) can prevent acute infections, and T-bet promotes IgG2a isotype switching. However, whether IgG2a and B cell-expressed T-bet influence the host-pathogen balance during persisting infections is unclear. We demonstrate that B cell-specific loss of T-bet prevents control of persisting viral infection. T-bet in B cells controlled IgG2a production, as well as mucosal localization, proliferation, glycosylation, and a broad transcriptional program. T-bet controlled a broad antiviral program in addition to IgG2a because T-bet in B cells was important, even in the presence of virus-specific IgG2a. Our data support a model in which T-bet is a universal controller of antiviral immunity across multiple immune lineages. Copyright © 2016 by The American Association of Immunologists, Inc.

  12. Isolation and characterization of a cDNA clone encoding an auxin influx carrier in carnation cuttings. Expression in different organs and cultivars and its relationship with cold storage.

    PubMed

    Oliveros-Valenzuela, María Del Rocío; Reyes, David; Sánchez-Bravo, José; Acosta, Manuel; Nicolás, Carlos

    2008-12-01

    Polar auxin transport (PAT) is necessary for the formation of adventitious roots in the base of leafy stem cuttings, as has been demonstrated in several studies in which the application of PAT inhibitors strongly inhibited the rooting of cuttings. However, unlike in the case of lateral roots, there is almost no information on the molecular mechanism that controls PAT in the formation of adventitious roots. A novel cDNA encoding an auxin influx carrier has been isolated and characterized from carnation (Dianthus caryophyllus) cuttings. The full length of DcAUX1 was obtained and the deduced aminoacid sequence revealed a high degree of identity with the corresponding auxin carrier proteins from several species. The expression of this gene depended on the organ, the carnation cultivar and the length of time cuttings had been stored in a cold chamber. As a rule, expression was higher in stem than in leaves, in the basal than in the first internode and in mature than in young leaves irrespective of the cultivar and the duration of the storage. This pattern of expression agrees with the results of a previous study showing that auxin from mature leaves was essential for rooting, while exogenous auxin applied to mature leaves was polarly transported in the stem and accumulated in the basal internode (the rooting zone). Variations in the expression observed during storage (depending of the cultivar) might be related to the variation in PAT and rooting reported in previous studies.

  13. Cutting Edge: IL-4, IL-21, and IFN-γ Interact To Govern T-bet and CD11c Expression in TLR-Activated B Cells.

    PubMed

    Naradikian, Martin S; Myles, Arpita; Beiting, Daniel P; Roberts, Kenneth J; Dawson, Lucas; Herati, Ramin Sedaghat; Bengsch, Bertram; Linderman, Susanne L; Stelekati, Erietta; Spolski, Rosanne; Wherry, E John; Hunter, Christopher; Hensley, Scott E; Leonard, Warren J; Cancro, Michael P

    2016-08-15

    T-bet and CD11c expression in B cells is linked with IgG2c isotype switching, virus-specific immune responses, and humoral autoimmunity. However, the activation requisites and regulatory cues governing T-bet and CD11c expression in B cells remain poorly defined. In this article, we reveal a relationship among TLR engagement, IL-4, IL-21, and IFN-γ that regulates T-bet expression in B cells. We find that IL-21 or IFN-γ directly promote T-bet expression in the context of TLR engagement. Further, IL-4 antagonizes T-bet induction. Finally, IL-21, but not IFN-γ, promotes CD11c expression independent of T-bet. Using influenza virus and Heligmosomoides polygyrus infections, we show that these interactions function in vivo to determine whether T-bet(+) and CD11c(+) B cells are formed. These findings suggest that T-bet(+) B cells seen in health and disease share the common initiating features of TLR-driven activation within this circumscribed cytokine milieu. Copyright © 2016 by The American Association of Immunologists, Inc.

  14. Cutting forces in orthogonal cutting of unidirectional GFRP composites

    SciTech Connect

    Caprino, G.; Nele, L.

    1996-07-01

    The results of orthogonal cutting tests carried out on unidirectional glass fiber reinforced plastic composites, using HSS tools, are presented and discussed. During the tests, performed on a milling machine at very low cutting speed to avoid thermal effects, the cutting speed was held constant and parallel to the fiber direction. Three parameters, namely the tool rake angle {alpha}, the tool relief angle {gamma}, and the depth of cut t, were varied. According to the experimental results, the horizontal force per unit width, F{sub hu}, undergoes a dramatic decrease, never verified for metals, with increasing {alpha}. Besides, F{sub hu} is only negligibly affected by the relief angle, and linearly increases with t. Similarly to metals, an effect of the depth of cut on the specific energy (size effect) is found also for composites. However, the presented results indicate that the size effect can be analytically modeled in a simple way in the case of composites. The vertical force per unit width, F{sub vu}, exhibits a marked reduction when the relief angle is increased. F{sub vu} is also very sensitive to the rake angle: the lower {alpha}, the higher is F{sub vu}. It is shown that this behavior probably reflects a strong influence of the rake angle on the forces developing at the flank. A linear dependence of the vertical force on the depth of cut is also demonstrated. Finally, the experimental data are utilized to obtain empirical formulae, allowing an approximate evaluation of cutting forces.

  15. Cutting the Cord-2

    NASA Technical Reports Server (NTRS)

    2004-01-01

    This animation shows the view from the rear hazard avoidance cameras on the Mars Exploration Rover Spirit as the rover turns 45 degrees clockwise. This maneuver is the first step in a 3-point turn that will rotate the rover 115 degrees to face west. The rover must make this turn before rolling off the lander because airbags are blocking it from exiting from the front lander petal. Before this crucial turn took place, engineers instructed the rover to cut the final cord linking it to the lander. The turn took around 30 minutes to complete.

  16. Cutting the Cord

    NASA Technical Reports Server (NTRS)

    2004-01-01

    This animation shows the view from the front hazard avoidance cameras on the Mars Exploration Rover Spirit as the rover turns 45 degrees clockwise. This maneuver is the first step in a 3-point turn that will rotate the rover 115 degrees to face west. The rover must make this turn before rolling off the lander because airbags are blocking it from exiting off the front lander petal. Before this crucial turn could take place, engineers instructed the rover to cut the final cord linking it to the lander. The turn took around 30 minutes to complete.

  17. Cutting the Cord

    NASA Technical Reports Server (NTRS)

    2004-01-01

    This animation shows the view from the front hazard avoidance cameras on the Mars Exploration Rover Spirit as the rover turns 45 degrees clockwise. This maneuver is the first step in a 3-point turn that will rotate the rover 115 degrees to face west. The rover must make this turn before rolling off the lander because airbags are blocking it from exiting off the front lander petal. Before this crucial turn could take place, engineers instructed the rover to cut the final cord linking it to the lander. The turn took around 30 minutes to complete.

  18. Cutting the Cord-2

    NASA Technical Reports Server (NTRS)

    2004-01-01

    This animation shows the view from the rear hazard avoidance cameras on the Mars Exploration Rover Spirit as the rover turns 45 degrees clockwise. This maneuver is the first step in a 3-point turn that will rotate the rover 115 degrees to face west. The rover must make this turn before rolling off the lander because airbags are blocking it from exiting from the front lander petal. Before this crucial turn took place, engineers instructed the rover to cut the final cord linking it to the lander. The turn took around 30 minutes to complete.

  19. ADVANCED CUTTINGS TRANSPORT STUDY

    SciTech Connect

    Troy Reed; Stefan Miska; Nicholas Takach; Kaveh Ashenayi; Mark Pickell; Len Volk; Mike Volk; Lei Zhou; Zhu Chen; Crystal Redden; Aimee Washington

    2003-07-30

    This Quarter has been divided between running experiments and the installation of the drill-pipe rotation system. In addition, valves and piping were relocated, and three viewports were installed. Detailed design work is proceeding on a system to elevate the drill-string section. Design of the first prototype version of a Foam Generator has been finalized, and fabrication is underway. This will be used to determine the relationship between surface roughness and ''slip'' of foams at solid boundaries. Additional cups and rotors are being machined with different surface roughness. Some experiments on cuttings transport with aerated fluids have been conducted at EPET. Theoretical modeling of cuttings transport with aerated fluids is proceeding. The development of theoretical models to predict frictional pressure losses of flowing foam is in progress. The new board design for instrumentation to measure cuttings concentration is now functioning with an acceptable noise level. The ultrasonic sensors are stable up to 190 F. Static tests with sand in an annulus indicate that the system is able to distinguish between different sand concentrations. Viscometer tests with foam, generated by the Dynamic Test Facility (DTF), are continuing.

  20. 75 FR 353 - AES Sparrows Point LNG, LLC and Mid-Atlantic Express, LLC; Notice of Availability of the Final...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-01-05

    ... Final General Conformity Determination for Maryland for the Proposed Sparrows Point LNG Terminal and...) import terminal and natural gas pipeline proposed by AES Sparrows Point LNG, LLC and Mid-Atlantic Express... following LNG terminal and natural gas pipeline facilities: A ship unloading facility, with two...

  1. Cutting meat with bone using an ultrahigh pressure abrasive waterjet.

    PubMed

    Wang, J; Shanmugam, D K

    2009-04-01

    An experimental study of abrasive waterjet (AWJ) cutting of beef, pork and lamb meat with and without bone is presented. Salt particles were used as the abrasives. It has been found that an AWJ could significantly increase the depth of cut with much improved cut quality in cutting pure meat as compared to plain (or pure) waterjet cutting, while a plain waterjet was incapable of cutting bone satisfactorily. The study shows that AWJ cutting produced a very narrow kerf of less than 1mm and hence resulted in mush less meat loss than the traditional cutting processes, and meat can be cut at room temperature to eliminate the freezing or chilling costs. It is shown that a traverses speed of 20mm/s can be used to cut through 44mm thick beef rib bones with good cut quality. When slicing pure meat of 150mm thickness, the traverse speed of 66.67mm/s can yield very good cut quality. It is suggested that AWJ cutting is a viable technology for meat cutting. Plausible trends for the depth of cut, cutting rate and cut quality with respect to the process variables are discussed. Recommendations are finally made for the selection of the most appropriate process parameters for cutting meat of a given thickness.

  2. A Dictionary of Hindi Verbal Expressions (Hindi-English). Final Report.

    ERIC Educational Resources Information Center

    Bahl, Kali Charan, Comp.

    This dictionary covers approximately 28,277 verbal expressions in modern standard Hindi and their rendered English equivalents. The study lists longer verbal expressions which are generally matched by single verbs in English. The lexicographer notes that the majority of entries in this dictionary do not appear in their present form in most other…

  3. Portable cutting apparatus

    DOEpatents

    Gilmore, R.F.

    1984-07-17

    A remotely operable, portable cutting apparatus detachably secured to the workpiece by laterally spaced clamp assemblies engagable with the workpiece on opposite sides of the intended line of cut. A reciprocal cutter head is mounted between the clamp assemblies and is provided with a traveling abrasive cutting wire adapted to sever the workpiece normal to the longitudinal axis thereof. Dust and debris are withdrawn from the cutting area by a vacuum force through a nozzle mounted on the cutting head.

  4. Portable cutting apparatus

    DOEpatents

    Gilmore, Richard F.

    1986-01-01

    A remotely operable, portable cutting apparatus detachably secured to the workpiece by laterally spaced clamp assemblies engageable with the workpiece on opposite sides of the intended line of cut. A reciprocal cutter head is mounted between the clamp assemblies and is provided with a traveling abrasive cutting wire adapted to sever the workpiece normal to the longitudinal axis thereof. Dust and debris are withdrawn from the cutting area by a vacuum force through a nozzle mounted on the cutting head.

  5. Portable cutting apparatus

    DOEpatents

    Gilmore, Richard F.

    1986-04-01

    A remotely operable, portable cutting apparatus detachably secured to the workpiece by laterally spaced clamp assemblies engageable with the workpiece on opposite sides of the intended line of cut. A reciprocal cutter head is mounted between the clamp assemblies and is provided with a traveling abrasive cutting wire adapted to sever the workpiece normal to the longitudinal axis thereof. Dust and debris are withdrawn from the cutting area by a vacuum force through a nozzle mounted on the cutting head.

  6. The Cutting-Edge Challenge

    ERIC Educational Resources Information Center

    Share, Joani

    2005-01-01

    In a time of educational budget cuts, the arts seem to take the major brunt of the financial ax. Fine arts programs are often pitted against one another for survival. The music industry and supporting corporations, such as American Express, campaign to have instruments donated or purchased to keep educational programs alive. The visual arts do not…

  7. The Cutting-Edge Challenge

    ERIC Educational Resources Information Center

    Share, Joani

    2005-01-01

    In a time of educational budget cuts, the arts seem to take the major brunt of the financial ax. Fine arts programs are often pitted against one another for survival. The music industry and supporting corporations, such as American Express, campaign to have instruments donated or purchased to keep educational programs alive. The visual arts do not…

  8. Making the cut

    PubMed Central

    Millard, Chris

    2013-01-01

    ‘Deliberate self-harm’, ‘self-mutilation’ and ‘self-injury’ are just some of the terms used to describe one of the most prominent issues in British mental health policy in recent years. This article demonstrates that contemporary literature on ‘self-harm’ produces this phenomenon (to varying extents) around two key characteristics. First, this behaviour is predominantly performed by those identified as female. Second, this behaviour primarily involves cutting the skin. These constitutive characteristics are traced back to a corpus of literature produced in the 1960s and 1970s in North American psychiatric inpatient institutions; analysis shows how pre-1960 works were substantially different. Finally, these gendered and behavioural assertions are shown to be the result of historically specific processes of exclusion and emphasis. PMID:23741086

  9. Vortex cutting in superconductors

    SciTech Connect

    Glatz, A.; Vlasko-Vlasov, V. K.; Kwok, W. K.; Crabtree, G. W.

    2016-08-09

    Vortex cutting and reconnection is an intriguing and still-unsolved problem central to many areas of classical and quantum physics, including hydrodynamics, astrophysics, and superconductivity. Here, in this paper, we describe a comprehensive investigation of the crossing of magnetic vortices in superconductors using time dependent Ginsburg-Landau modeling. Within a macroscopic volume, we simulate initial magnetization of an anisotropic high temperature superconductor followed by subsequent remagnetization with perpendicular magnetic fields, creating the crossing of the initial and newly generated vortices. The time resolved evolution of vortex lines as they approach each other, contort, locally conjoin, and detach, elucidates the fine details of the vortex-crossing scenario under practical situations with many interacting vortices in the presence of weak pinning. Finally, our simulations also reveal left-handed helical vortex instabilities that accompany the remagnetization process and participate in the vortex crossing events.

  10. Vortex cutting in superconductors

    DOE PAGES

    Glatz, A.; Vlasko-Vlasov, V. K.; Kwok, W. K.; ...

    2016-08-09

    Vortex cutting and reconnection is an intriguing and still-unsolved problem central to many areas of classical and quantum physics, including hydrodynamics, astrophysics, and superconductivity. Here, in this paper, we describe a comprehensive investigation of the crossing of magnetic vortices in superconductors using time dependent Ginsburg-Landau modeling. Within a macroscopic volume, we simulate initial magnetization of an anisotropic high temperature superconductor followed by subsequent remagnetization with perpendicular magnetic fields, creating the crossing of the initial and newly generated vortices. The time resolved evolution of vortex lines as they approach each other, contort, locally conjoin, and detach, elucidates the fine details ofmore » the vortex-crossing scenario under practical situations with many interacting vortices in the presence of weak pinning. Finally, our simulations also reveal left-handed helical vortex instabilities that accompany the remagnetization process and participate in the vortex crossing events.« less

  11. Cutting state identification

    SciTech Connect

    Berger, B.S.; Minis, I.; Rokni, M.

    1997-12-31

    Cutting states associated with the orthogonal cutting of stiff cylinders are identified through an analysis of the singular values of a Toeplitz matrix of third order cumulants of acceleration measurements. The ratio of the two pairs of largest singular values is shown to differentiate between light cutting, medium cutting, pre-chatter and chatter states. Sequences of cutting experiments were performed in which either depth of cut or turning frequency was varied. Two sequences of experiments with variable turning frequency and five with variable depth of cut, 42 cutting experiments in all, provided a database for the calculation of third order cumulants. Ratios of singular values of cumulant matrices find application in the analysis of control of orthogonal cutting.

  12. Columbia/Willamette Skill Builders Consortium. Final Performance Report. Appendix 5A: Oregon Cutting Systems and Warn Industries, Inc. Basic Math/Shop Math and Computer Basics. Instructors' Reports and Sample Curriculum Materials.

    ERIC Educational Resources Information Center

    Copeland, Scott

    Workplace literacy projects were established at Warn Industries, a winch and hubcap maker, and Oregon Cutting Systems (OCS), a producer of cutting edges supplying the timber industry by Clackamas Community College (Oregon). At Warn, project staff developed functional context materials, delivered instruction to a math class, and implemented a basic…

  13. Simulation of Laser Cutting

    NASA Astrophysics Data System (ADS)

    Schulz, Wolfgang; Nießen, Markus; Eppelt, Urs; Kowalick, Kerstin

    Laser cutting is a thermal separation process widely used in shaping and contour cutting applications. There are, however, gaps in understanding the dynamics of the process, especially issues related to cut quality. This work describes the advances in fundamental physical modelling and process monitoring of laser cutting, as well as time varying processes such as contour cutting. Diagnosis of ripple and dross formation is advanced to observe the melt flow and its separation simultaneously as well as the spatial shape of the cut kerf.

  14. Highspeed laser ablation cutting of metal

    NASA Astrophysics Data System (ADS)

    Ullmann, F.; Loeschner, U.; Hartwig, L.; Szczepanski, D.; Schille, J.; Gronau, S.; Knebel, T.; Drechsel, J.; Ebert, R.; Exner, H.

    2013-02-01

    In laser ablation cutting, irradiation of high-intense laser beams causes ejection of molten and evaporated material out of the cutting zone as a result of high pressure gradients, induced by expanding plasma plumes. This paper investigates highspeed laser ablation cutting of industrial grade metal sheets using high-brilliant continuous wave fiber lasers with output powers up to 5 kW. The laser beam was deflected with scan speeds up to 2700 m/min utilizing both a fast galvanometer scan system and a polygon scan system. By sharp laser beam focusing using different objectives with focal lengths ranging between 160 mm and 500 mm, small laser spot diameters between 16.5 μm and 60 μm were obtained, respectively. As a result high peak intensities between 3*108 W/cm² and 2.5*109 W/cm² were irradiated on the sample surface, and cutting kerfs with a maximum depth of 1.4 mm have been produced. In this study the impact of the processing parameters laser power, laser spot diameter, cutting speed, and number of scans on both the achievable cutting depth and the cutting edge quality was investigated. The ablation depths, the heights of the cutting burr, as well as the removed material volumes were evaluated by means of optical microscope images and cross section photographs. Finally highspeed laser ablation cutting was studied using an intensified ultra highspeed camera in order to get useful insights into the cutting process.

  15. D-dimer use for deep venous thrombosis exclusion in elderly patients: a comparative analysis of three different approaches to establish cut-off values for an assay with results expressed in D-dimer units.

    PubMed

    Cini, M; Legnani, C; Frascaro, M; Sartori, M; Cosmi, B; Palareti, G

    2014-10-01

    The use of adapted cut-off values in the elderly, combined with clinical probability (PTP), increases the proportion of patients in whom venous thromboembolism (VTE) can be safely excluded, compared with the conventional cut-off value of 500 μg/L fibrinogen equivalent units (FEU). We evaluated the clinical performance of three different approaches to establish cut-off values for a D-dimer assay whose results are expressed in D-dimer units (D-DU). HemosIL D-dimer HS assay (Instrumentation Laboratory) was performed in 279 consecutive outpatients with suspected deep venous thrombosis (DVT) and nonhigh PTP. Considering patients >60 years, the number of negative D-dimer results increased using the modified (376 ng/mL if ≥60 years) and the age-adjusted cut-off (age years × 5 ng/mL if >50 years) compared to the conventional one (230 ng/mL for all patients; 54.6%, 58.2%, and 25.0%, respectively), with no false-negative results. The higher increase was observed in patients >80 years (43.9%, 56.1%, and 8.8%, respectively). For the HemosIL D-dimer HS, the use of specific cut-off values in older subjects with suspected DVT and nonhigh PTP increases the number of patients in whom DVT can be safely excluded. © 2014 John Wiley & Sons Ltd.

  16. The Georgia Express: Final Report. A 310 Planning Project for Adult Education.

    ERIC Educational Resources Information Center

    Griffin City - Spalding County Board of Education, GA.

    This report summarizes the work of the Georgia Express project staff and the five task teams that provided research services to the Georgia Task Force on Adult Education. (The purpose of the Task Force was to review Georgia Adult Education's current goals, objectives, and procedures and to make recommendations for program improvement.) The report…

  17. AXIS (Adult Education Express Intercommunication Support) Final Report, 1999-2000.

    ERIC Educational Resources Information Center

    Reiff, Tana

    The project AXIS: Adult education eXpress Intercommunication Support was designed to provide systematic communication and coordination between Pennsylvania's Bureau of Adult Basic and Literacy Education and professional service providers and adult basic and literacy education (ABLE) providers, including support for online and World Wide Web…

  18. Genetic analysis of the regulation of TCH gene expression, Final Report

    SciTech Connect

    Braam, Janet

    2008-10-28

    The Arabidopsis TCH genes, originally isolated as a consequence of their upregulation in response to the mechanical stimulus of touch, are also upregulated by a variety of seemingly disparate environmental and hormonal stimuli. To gain insight into the complexities of TCH gene regulation, a number of approaches were taken. Regulatory elements responsible for regulation were identified and characteristics of the regulation were evaluated. Reporter genes were used to monitor expression localization and dynamics. Microarray analyses of genome-wide expression behavior indicated that touch-inducible gene expression is more widespread than generally appreciated. Identification of all touch-regulated genes shed light on the types of cellular processes that may be altered in response to mechanical stress perturbations. Expression of the TCH2 gene, also called CML24, encoding a calmodulin (CaM)-like (CML) protein, was evaluated. CML24 shares over 40% amino acid sequence identity with CaM, has 4 EF hands and undergoes a Ca2+-dependent change in migration rate through denaturing gel electrophoresis, indicating that CML24 binds Ca2+ and, as a consequence, undergoes conformational changes. CML24 expression occurs in all major organs and is induced from 2- to 15-fold in plants subjected to touch, darkness, heat, cold, hydrogen peroxide, abscisic acid (ABA) and indole-3-acetic acid. The putative CML24 regulatory region confers reporter expression at sites of predicted mechanical stress, in regions undergoing growth, in vascular tissues and various floral organs and in stomata, trichomes and hydathodes. CML24 underexpressing transgenics are resistant to ABA inhibition of germination and seedling growth, defective in long-day induction of flowering, and have enhanced tolerance to CoCl2, molybdic acid, ZnSO4 and MgCl2. These data present evidence that CML24 encodes a potential Ca2+ sensor that may function to enable responses to ABA, day length and presence of various salts. Further

  19. Cutting edge: the "death" adaptor CRADD/RAIDD targets BCL10 and suppresses agonist-induced cytokine expression in T lymphocytes.

    PubMed

    Lin, Qing; Liu, Yan; Moore, Daniel J; Elizer, Sydney K; Veach, Ruth A; Hawiger, Jacek; Ruley, H Earl

    2012-03-15

    The expression of proinflammatory cytokines and chemokines in response to TCR agonists is regulated by the caspase-recruitment domain membrane-associated guanylate kinase 1 (CARMA1) signalosome through the coordinated assembly of complexes containing the BCL10 adaptor protein. We describe a novel mechanism to negatively regulate the CARMA1 signalosome by the "death" adaptor protein caspase and receptor interacting protein adaptor with death domain (CRADD)/receptor interacting protein-associated ICH-1/CED-3 homologous protein with a death domain. We show that CRADD interacts with BCL10 through its caspase recruitment domain and suppresses interactions between BCL10 and CARMA1. TCR agonist-induced interaction between CRADD and BCL10 coincides with reduction of its complex formation with CARMA1 in wild-type, as compared with Cradd-deficient, primary cells. Finally, Cradd-deficient spleen cells, CD4(+) T cells, and mice respond to T cell agonists with strikingly higher production of proinflammatory mediators, including IFN-γ, IL-2, TNF-α, and IL-17. These results define a novel role for CRADD as a negative regulator of the CARMA1 signalosome and suppressor of Th1- and Th17-mediated inflammatory responses.

  20. Structure and expression of nuclear genes encoding rubisco activase. Final technical report

    SciTech Connect

    Zielinski, R.E.

    1994-06-01

    Rubisco activase (Rca) is a soluble chloroplast protein that catalyzes the activation of rubisco, the enzyme that initiates the photosynthetic carbon reduction cycle, to catalytic competency. Rca in barley consists of three polypeptides, one of 46- and two of 42-kDa, but the quaternary structure of the protein is not known. The authors have isolated and completely sequenced 8.8 kb of barley genomic DNA containing two, tandemly oriented activase genes (RcaA and RcaB) and three different cDNAs encoding the 42- and 46-kDa Rca polypeptide isoforms. Genomic Southern blot assays indicate that these sequences represent the entire Rca gene family in barley. Pre-mRNAs transcribed from the RcaA gene are alternatively spliced to give mRNAs encoding both 46- (RcaA1) and 42-kDa (RcaA2) Rca isoforms. The RcaB gene encodes a single polypeptide of 42 kDa. Primer extension and northern blot assays indicate that RcaB mRNA is expressed at a level that is 10- to 100-fold lower than RcaA mRNA. Analyses at the mRNA and protein level showed that Rca gene expression is coordinated by that of the rubisco subunits during barley leaf development.

  1. Device for cutting protrusions

    DOEpatents

    Bzorgi, Fariborz M [Knoxville, TN

    2011-07-05

    An apparatus for clipping a protrusion of material is provided. The protrusion may, for example, be a bolt head, a nut, a rivet, a weld bead, or a temporary assembly alignment tab protruding from a substrate surface of assembled components. The apparatus typically includes a cleaver having a cleaving edge and a cutting blade having a cutting edge. Generally, a mounting structure configured to confine the cleaver and the cutting blade and permit a range of relative movement between the cleaving edge and the cutting edge is provided. Also typically included is a power device coupled to the cutting blade. The power device is configured to move the cutting edge toward the cleaving edge. In some embodiments the power device is activated by a momentary switch. A retraction device is also generally provided, where the retraction device is configured to move the cutting edge away from the cleaving edge.

  2. Lineaments of Texas - possible surface expressions of deep-seated phenomena. Final report

    SciTech Connect

    Woodruff, C.M. Jr.; Caran, S.C.

    1984-04-01

    Lineaments were identified on 51 Landsat images covering Texas and parts of adjacent states in Mexico and the United States. A method of identifying lineaments was designed so that the findings would be consistent, uncomplicated, objective, and reproducible. Lineaments denoted on the Landsat images were traced onto 1:250,000-scale work maps and then rendered cartographically on maps representing each of the 51 Landsat images at a scale of 1:500,000. At this stage more than 31,000 lineaments were identified. It included significant areas outside of Texas. In preparing the final lineament map of Texas at 1:1,000,000-scale from the 1:500,000-scale maps, all features that lay outside Texas and repetition among features perceived by individual workers were eliminated. Cultural features were checked for before reducing and cartographically fitting the mosaic of 51 individual map sheets to a single map base. Lineaments that were partly colinear but with different end points were modified into a single lineament trace with the combined length of the two or more colinear lineaments. Each lineament was checked to determine its validity according to our definition. The features were edited again to eliminate processing artifacts within the image itself, as well as representations of cultural features (fencelines, roads, and the like) and geomorphic patterns unrelated to bedrock structure. Thus the more than 31,000 lineaments originally perceived were reduced to the approximately 15,000 presented on the 1:1,000,000 map. Interpretations of the lineaments are presented.

  3. ADVANCED CUTTINGS TRANSPORT STUDY

    SciTech Connect

    Stefan Miska; Nicholas Takach; Kaveh Ashenayi

    2004-01-31

    Final design of the mast was completed (Task 5). The mast is consisting of two welded plate girders, set next to each other, and spaced 14-inches apart. Fabrication of the boom will be completed in two parts solely for ease of transportation. The end pivot connection will be made through a single 2-inch diameter x 4 feet-8 inch long 316 SS bar. During installation, hard piping make-ups using Chiksan joints will connect the annular section and 4-inch return line to allow full movement of the mast from horizontal to vertical. Additionally, flexible hoses and piping will be installed to isolate both towers from piping loads and allow recycling operations respectively. Calibration of the prototype Foam Generator Cell has been completed and experiments are now being conducted. We were able to generate up to 95% quality foam. Work is currently underway to attach the Thermo-Haake RS300 viscometer and install a view port with a microscope to measure foam bubble size and bubble size distribution. Foam rheology tests (Task 13) were carried out to evaluate the rheological properties of the proposed foam formulation. After successful completion of the first foam test, two sets of rheological tests were conducted at different foam flow rates while keeping other parameters constant (100 psig, 70F, 80% quality). The results from these tests are generally in agreement with the previous foam tests done previously during Task 9. However, an unanticipated observation during these tests was that in both cases, the frictional pressure drop in 2 inch pipe was lower than that in the 3 inch and 4 inch pipes. We also conducted the first foam cuttings transport test during this quarter. Experiments on aerated fluids without cuttings have been completed in ACTF (Task 10). Gas and liquid were injected at different flow rates. Two different sets of experiments were carried out, where the only difference was the temperature. Another set of tests was performed, which covered a wide range of

  4. Laser cutting plastic materials

    SciTech Connect

    Van Cleave, R.A.

    1980-08-01

    A 1000-watt CO/sub 2/ laser has been demonstrated as a reliable production machine tool for cutting of plastics, high strength reinforced composites, and other nonmetals. More than 40 different plastics have been laser cut, and the results are tabulated. Applications for laser cutting described include fiberglass-reinforced laminates, Kevlar/epoxy composites, fiberglass-reinforced phenolics, nylon/epoxy laminates, ceramics, and disposable tooling made from acrylic.

  5. Ultrasonic Cutting of Foods

    NASA Astrophysics Data System (ADS)

    Schneider, Yvonne; Zahn, Susann; Rohm, Harald

    In the field of food engineering, cutting is usually classified as a mechanical unit operation dealing with size reduction by applying external forces on a bulk product. Ultrasonic cutting is realized by superpositioning the macroscopic feed motion of the cutting device or of the product with a microscopic vibration of the cutting tool. The excited tool interacts with the product and generates a number of effects. Primary energy concentration in the separation zone and the modification of contact friction along the tool flanks arise from the cyclic loading and are responsible for benefits such as reduced cutting force, smooth cut surface, and reduced product deformation. Secondary effects such as absorption and cavitation originate from the propagation of the sound field in the product and are closely related to chemical and physical properties of the material to be cut. This chapter analyzes interactions between food products and ultrasonic cutting tools and relates these interactions with physical and chemical product properties as well as with processing parameters like cutting velocity, ultrasonic amplitude and frequency, and tool design.

  6. In Vitro Culture Conditions and OeARF and OeH3 Expressions Modulate Adventitious Root Formation from Oleaster (Olea europaea L. subsp. europaea var. sylvestris) Cuttings

    PubMed Central

    Gagliardi, Cinzia; Bruno, Leonardo; Bitonti, Maria Beatrice

    2014-01-01

    Olea europaea L. subsp. europaea var. sylvestris, also named oleaster, is the wild form of olive and it is used as rootstock and pollen donor for many cultivated varieties. An efficient procedure for in vitro propagation of oleaster was established in this study. A zeatin concentration of 2.5 mg/L was effective to induce an appreciable vegetative growth. Also high rooting efficiency was obtained by using a short IBA pulse, followed by two different IBA concentrations in the culture medium. With the aim to enlarge knowledge on the molecular aspects of adventitious rooting, we also evaluated the transcriptional modulation of an ARFs member and HISTONE H3 genes, involved in auxin signaling and cell replication, respectively, during the root induction phase of cuttings. The obtained results suggest that the selected genes, as markers of the induction phase, could be very useful for setting up efficient culture conditions along the rooting process, thus increasing micropropagation efficiency. PMID:24587768

  7. In vitro culture conditions and OeARF and OeH3 expressions modulate adventitious root formation from oleaster (Olea europaea L. subsp. europaea var. sylvestris) cuttings.

    PubMed

    Chiappetta, Adriana; Gagliardi, Cinzia; Bruno, Leonardo; Bitonti, Maria Beatrice

    2014-01-01

    Olea europaea L. subsp. europaea var. sylvestris, also named oleaster, is the wild form of olive and it is used as rootstock and pollen donor for many cultivated varieties. An efficient procedure for in vitro propagation of oleaster was established in this study. A zeatin concentration of 2.5 mg/L was effective to induce an appreciable vegetative growth. Also high rooting efficiency was obtained by using a short IBA pulse, followed by two different IBA concentrations in the culture medium. With the aim to enlarge knowledge on the molecular aspects of adventitious rooting, we also evaluated the transcriptional modulation of an ARFs member and HISTONE H3 genes, involved in auxin signaling and cell replication, respectively, during the root induction phase of cuttings. The obtained results suggest that the selected genes, as markers of the induction phase, could be very useful for setting up efficient culture conditions along the rooting process, thus increasing micropropagation efficiency.

  8. Laser fusion cutting using supersonic nozzles

    NASA Astrophysics Data System (ADS)

    Duan, Jun

    This research takes a systematic approach to study the flow patterns of gas jets from the conventional conical (subsonic) nozzle and the newly designed supersonic nozzle under a high-pressure gas regime by a three-dimensional mathematical model. Computer simulation was then confirmed by experimental shadowgraphic technique. The relationships between the type of nozzles, nozzle dimensions, stand-off distance, inlet stagnation pressure and the flow field distribution, incident shock and normal shock have been established. Compared with that of the subsonic nozzle, the gas jet from a supersonic nozzle possesses the desired dynamic characteristics such as uniform distribution, maximum and even momentum thrust and parallel jet boundary under the condition of the designed pressures. Then, a model calculating the three-dimensional stationary geometric shape of the cutting front obtained in the high-pressure laser fusion cutting regime was developed using numerical solution of energy balance. In this model, the energy absorbed by the workpiece includes not only the energy from the laser beam but also the energy from the multiple reflections generated by the beam impinging at the cutting front. The effects of the laser power, cutting speed, focus position, multiple reflections and inert gas pressure on the geometric shape of the cutting front have been analyzed systemically. The geometric shape of the cutting front was then used as boundary conditions in subsequent calculation of the gas flow field distribution inside a laser cut kerf. Finally, a third mathematical model was developed to calculate the distribution of the gas flow field at the entrance of the cut kerf, inside the cut kerf and at the exit of a cut kerf under the condition of a gas jet from a supersonic nozzle and the inlet stagnation pressure ≥5 bar. A two-dimensional analytical method was adopted to locate approximately the position and shape of the detached shock above the cut kerf. A method of two

  9. Cutting Class Harms Grades

    ERIC Educational Resources Information Center

    Taylor, Lewis A., III

    2012-01-01

    An accessible business school population of undergraduate students was investigated in three independent, but related studies to determine effects on grades due to cutting class and failing to take advantage of optional reviews and study quizzes. It was hypothesized that cutting classes harms exam scores, attending preexam reviews helps exam…

  10. Starting Trees from Cuttings.

    ERIC Educational Resources Information Center

    Kramer, David C.

    1983-01-01

    Describes a procedure for starting tree cuttings from woody plants, explaining "lag time," recommending materials, and giving step-by-step instructions for rooting and planting. Points out species which are likely candidates for cuttings and provides tips for teachers for developing a unit. (JM)

  11. When Students Cut Themselves

    ERIC Educational Resources Information Center

    Malikow, Max

    2006-01-01

    Masochism, the irrational self-infliction of pain, is more easily defined than understood. Once, a teacher used the word "cutting" only reference to a student skipping class. But, in recent years, it has taken on additional meaning. Cutting, or self-injury, is a deliberate self-harming behavior but without conscious suicidal ideation. To define…

  12. When Students Cut Themselves

    ERIC Educational Resources Information Center

    Malikow, Max

    2006-01-01

    Masochism, the irrational self-infliction of pain, is more easily defined than understood. Once, a teacher used the word "cutting" only reference to a student skipping class. But, in recent years, it has taken on additional meaning. Cutting, or self-injury, is a deliberate self-harming behavior but without conscious suicidal ideation. To define…

  13. Cutting Class Harms Grades

    ERIC Educational Resources Information Center

    Taylor, Lewis A., III

    2012-01-01

    An accessible business school population of undergraduate students was investigated in three independent, but related studies to determine effects on grades due to cutting class and failing to take advantage of optional reviews and study quizzes. It was hypothesized that cutting classes harms exam scores, attending preexam reviews helps exam…

  14. Fundamentals of cutting

    PubMed Central

    Williams, J. G.; Patel, Y.

    2016-01-01

    The process of cutting is analysed in fracture mechanics terms with a view to quantifying the various parameters involved. The model used is that of orthogonal cutting with a wedge removing a layer of material or chip. The behaviour of the chip is governed by its thickness and for large radii of curvature the chip is elastic and smooth cutting occurs. For smaller thicknesses, there is a transition, first to plastic bending and then to plastic shear for small thicknesses and smooth chips are formed. The governing parameters are tool geometry, which is principally the wedge angle, and the material properties of elastic modulus, yield stress and fracture toughness. Friction can also be important. It is demonstrated that the cutting process may be quantified via these parameters, which could be useful in the study of cutting in biology. PMID:27274798

  15. Fundamentals of cutting.

    PubMed

    Williams, J G; Patel, Y

    2016-06-06

    The process of cutting is analysed in fracture mechanics terms with a view to quantifying the various parameters involved. The model used is that of orthogonal cutting with a wedge removing a layer of material or chip. The behaviour of the chip is governed by its thickness and for large radii of curvature the chip is elastic and smooth cutting occurs. For smaller thicknesses, there is a transition, first to plastic bending and then to plastic shear for small thicknesses and smooth chips are formed. The governing parameters are tool geometry, which is principally the wedge angle, and the material properties of elastic modulus, yield stress and fracture toughness. Friction can also be important. It is demonstrated that the cutting process may be quantified via these parameters, which could be useful in the study of cutting in biology.

  16. Automated Cell-Cutting for Cell Cloning

    NASA Astrophysics Data System (ADS)

    Ichikawa, Akihiko; Tanikawa, Tamio; Matsukawa, Kazutsugu; Takahashi, Seiya; Ohba, Kohtaro

    We develop an automated cell-cutting technique for cell cloning. Animal cells softened by the cytochalasin treatment are injected into a microfluidic chip. The microfluidic chip contains two orthogonal channels: one microchannel is wide, used to transport cells, and generates the cutting flow; the other is thin and used for aspiration, fixing, and stretching of the cell. The injected cell is aspirated and stretched in the thin microchannel. Simultaneously, the volumes of the cell before and after aspiration are calculated; the volumes are used to calculate the fluid flow required to aspirate half the volume of the cell into the thin microchannel. Finally, we apply a high-speed flow in the orthogonal microchannel to bisect the cell. This paper reports the cutting process, the cutting system, and the results of the experiment.

  17. INTERNAL CUTTING DEVICE

    DOEpatents

    Russell, W.H. Jr.

    1959-06-30

    A device is described for removing material from the interior of a hollow workpiece so as to form a true spherical internal surface in a workpiece, or to cut radial slots of an adjustable constant depth in an already established spherical internal surface. This is accomplished by a spring loaded cutting tool adapted to move axially wherein the entire force urging the tool against the workpiece is derived from the spring. Further features of importance involve the provision of a seal between the workpiece and the cutting device and a suction device for carrying away particles of removed material.

  18. Testing Of Choiced Ceramics Cutting Tools At Irregular Interrupted Cut

    NASA Astrophysics Data System (ADS)

    Kyncl, Ladislav; Malotová, Šárka; Nováček, Pavel; Nicielnik, Henryk; Šoková, Dagmar; Hemžský, Pavel; Pitela, David; Holubjak, Jozef

    2015-12-01

    This article discusses the test of removable ceramic cutting inserts during machining irregular interrupted cut. Tests were performed on a lathe, with the preparation which simulated us the interrupted cut. By changing the number of plates mounted in a preparation it simulate us a regular or irregular interrupted cut. When with four plates it was regular interrupted cut, the remaining three variants were already irregular cut. It was examined whether it will have the irregular interrupted cutting effect on the insert and possibly how it will change life of inserts during irregular interrupted cut (variable delay between shocks).

  19. Cuts and puncture wounds

    MedlinePlus

    ... severely, call your local emergency number such as 911. Minor cuts and puncture wounds can be treated ... arrives. When to Contact a Medical Professional Call 911 or your local emergency number if: The bleeding ...

  20. INFINITY ribbon-cutting

    NASA Image and Video Library

    2012-04-11

    'Astronaut' Patrick Johnston, 8, is interviewed by Heath Allen, a reporter with WDSU-TV in New Orleans, about his experience at the INFINITY at NASA Stennis Space Center facility during ribbon-cutting activities April 11, 2012.

  1. Laser cutting system

    SciTech Connect

    Dougherty, Thomas J

    2015-03-03

    A workpiece cutting apparatus includes a laser source, a first suction system, and a first finger configured to guide a workpiece as it moves past the laser source. The first finger includes a first end provided adjacent a point where a laser from the laser source cuts the workpiece, and the first end of the first finger includes an aperture in fluid communication with the first suction system.

  2. ADVANCED CUTTINGS TRANSPORT STUDY

    SciTech Connect

    Troy Reed; Stefan Miska; Nicholas Takach; Kaveh Ashenayi; Mark Pickell; Len Volk; Mike Volk; Lei Zhou; Zhu Chen; Crystal Redden; Aimee Washington

    2003-01-30

    This is the second quarterly progress report for Year-4 of the ACTS Project. It includes a review of progress made in: (1) Flow Loop construction and development and (2) research tasks during the period of time between October 1, 2002 and December 30, 2002. This report presents a review of progress on the following specific tasks. (a) Design and development of an Advanced Cuttings Transport Facility Task 3: Addition of a Cuttings Injection/Separation System, Task 4: Addition of a Pipe Rotation System. (b) New research project (Task 9b): ''Development of a Foam Generator/Viscometer for Elevated Pressure and Elevated Temperature (EPET) Conditions''. (d) Research project (Task 10): ''Study of Cuttings Transport with Aerated Mud Under Elevated Pressure and Temperature Conditions''. (e) Research on three instrumentation tasks to measure: Cuttings concentration and distribution in a flowing slurry (Task 11), Foam texture while transporting cuttings. (Task 12), and Viscosity of Foam under EPET (Task 9b). (f) New Research project (Task 13): ''Study of Cuttings Transport with Foam under Elevated Pressure and Temperature Conditions''. (g) Development of a Safety program for the ACTS Flow Loop. Progress on a comprehensive safety review of all flow-loop components and operational procedures. (Task 1S). (h) Activities towards technology transfer and developing contacts with Petroleum and service company members, and increasing the number of JIP members.

  3. ADVANCED CUTTINGS TRANSPORT STUDY

    SciTech Connect

    Troy Reed; Stefan Miska; Nicholas Takach; Kaveh Ashenayi; Gerald Kane; Mark Pickell; Len Volk; Mike Volk; Affonso Lourenco; Evren Ozbayoglu; Lei Zhou

    2002-01-30

    This is the second quarterly progress report for Year 3 of the ACTS project. It includes a review of progress made in: (1) Flow Loop development and (2) research tasks during the period of time between Oct 1, 2001 and Dec. 31, 2001. This report presents a review of progress on the following specific tasks: (a) Design and development of an Advanced Cuttings Transport Facility (Task 3: Addition of a Cuttings Injection/Collection System), (b) Research project (Task 6): ''Study of Cuttings Transport with Foam Under LPAT Conditions (Joint Project with TUDRP)'', (c) Research project (Task 9): ''Study of Foam Flow Behavior Under EPET Conditions'', (d) Research project (Task 10): ''Study of Cuttings Transport with Aerated Mud Under Elevated Pressure and Temperature Conditions'', (e) Research on instrumentation tasks to measure: Cuttings concentration and distribution in a flowing slurry (Task 11), and Foam properties while transporting cuttings. (Task 12), (f) Development of a Safety program for the ACTS Flow Loop. Progress on a comprehensive safety review of all flow-loop components and operational procedures. (Task 1S). (g) Activities towards technology transfer and developing contacts with Petroleum and service company members, and increasing the number of JIP members.

  4. ADVANCED CUTTINGS TRANSPORT STUDY

    SciTech Connect

    Troy Reed; Stefan Miska; Nicholas Takach; Kaveh Ashenayi; Gerald Kane; Mark Pickell; Len Volk; Mike Volk; Barkim Demirdal; Affonso Lourenco; Evren Ozbayoglu; Paco Vieira; Lei Zhou

    2000-01-30

    This is the second quarterly progress report for Year 2 of the ACTS project. It includes a review of progress made in Flow Loop development and research during the period of time between Oct 1, 2000 and December 31, 2000. This report presents a review of progress on the following specific tasks: (a) Design and development of an Advanced Cuttings Transport Facility (Task 2: Addition of a foam generation and breaker system), (b) Research project (Task 6): ''Study of Cuttings Transport with Foam Under LPAT Conditions (Joint Project with TUDRP)'', (c) Research project (Task 7): ''Study of Cuttings Transport with Aerated Muds Under LPAT Conditions (Joint Project with TUDRP)'', (d) Research project (Task 8): ''Study of Flow of Synthetic Drilling Fluids Under Elevated Pressure and Temperature Conditions'', (e) Research project (Task 9): ''Study of Foam Flow Behavior Under EPET Conditions'', (f) Research project (Task 10): ''Study of Cuttings Transport with Aerated Mud Under Elevated Pressure and Temperature Conditions'', (g) Research on instrumentation tasks to measure: Cuttings concentration and distribution in a flowing slurry (Task 11), and Foam properties while transporting cuttings. (Task 12), (h) Development of a Safety program for the ACTS Flow Loop. Progress on a comprehensive safety review of all flow-loop components and operational procedures. (Task 1S). (i) Activities towards technology transfer and developing contacts with Petroleum and service company members, and increasing the number of JIP members. The tasks Completed During This Quarter are Task 7 and Task 8.

  5. ADVANCED CUTTINGS TRANSPORT STUDY

    SciTech Connect

    Troy Reed; Stefan Miska; Nicholas Takach; Kaveh Ashenayi; Mark Pickell; Len Volk; Mike Volk; Evren Ozbayoglu; Lei Zhou

    2002-04-30

    This is the third quarterly progress report for Year 3 of the ACTS Project. It includes a review of progress made in: (1) Flow Loop construction and development and (2) research tasks during the period of time between Jan. 1, 2002 and Mar. 31, 2002. This report presents a review of progress on the following specific tasks: (a) Design and development of an Advanced Cuttings Transport Facility (Task 3: Addition of a Cuttings Injection/Separation System), (b) Research project (Task 6): ''Study of Cuttings Transport with Foam Under LPAT Conditions (Joint Project with TUDRP)'', (c) Research project (Task 9b): ''Study of Foam Flow Behavior Under EPET Conditions'', (d) Research project (Task 10): ''Study of Cuttings Transport with Aerated Mud Under Elevated Pressure and Temperature Conditions'', (e) Research on three instrumentation tasks to measure: Cuttings concentration and distribution in a flowing slurry (Task 11), Foam texture while transporting cuttings. (Task 12), and Viscosity of Foam under EPET (Task 9b); (f) Development of a Safety program for the ACTS Flow Loop, progress on a comprehensive safety review of all flow-loop components and operational procedures. (Task 1S); and (g) Activities towards technology transfer and developing contacts with Petroleum and service company members, and increasing the number of JIP members.

  6. ADVANCED CUTTINGS TRANSPORT STUDY

    SciTech Connect

    Troy Reed; Stefan Miska; Nicholas Takach; Kaveh Ashenayi; Mark Pickell; Len Volk; Mike Volk; Evren Ozbayoglu; Lei Zhou

    2002-07-30

    This is the fourth quarterly progress report for Year-3 of the ACTS Project. It includes a review of progress made in: (1) Flow Loop construction and development and (2) research tasks during the period of time between April 1, 2002 and June 30, 2002. This report presents a review of progress on the following specific tasks: (a) Design and development of an Advanced Cuttings Transport Facility (Task 3: Addition of a Cuttings Injection/Separation System), (b) Research project (Task 6): ''Study of Cuttings Transport with Foam Under LPAT Conditions (Joint Project with TUDRP)''; (c) Research project (Task 9b): ''Study of Foam Flow Behavior Under EPET Conditions''; (d) Research project (Task 10): ''Study of Cuttings Transport with Aerated Mud Under Elevated Pressure and Temperature Conditions''; (e) Research on three instrumentation tasks to measure: Cuttings concentration and distribution in a flowing slurry (Task 11), Foam texture while transporting cuttings. (Task 12), and Viscosity of Foam under EPET (Task 9b); (f) Development of a Safety program for the ACTS Flow Loop. Progress on a comprehensive safety review of all flow-loop components and operational procedures. (Task 1S); (g) Activities towards technology transfer and developing contacts with Petroleum and service company members, and increasing the number of JIP members.

  7. Cutting edge: recombinant Listeria monocytogenes expressing a single immune-dominant peptide confers protective immunity to herpes simplex virus-1 infection.

    PubMed

    Orr, Mark T; Orgun, Nural N; Wilson, Christopher B; Way, Sing Sing

    2007-04-15

    The vast majority of the world's population is infected with HSV. Although antiviral therapy can reduce the incidence of reactivation and asymptomatic viral shedding, and limit morbidity and mortality from active disease, it cannot cure infection. Therefore, the development of an effective vaccine is an important global health priority. In this study, we demonstrate that recombinant Listeria monocytogenes (Lm) expressing the H-2K(b) glycoprotein B (gB)(498-505) peptide from HSV-1 triggers a robust CD8 T cell response to this Ag resulting in protective immunity to HSV infection. Following challenge with HSV-1, immune-competent mice primed with recombinant Lm-expressing gB(498-505) Ag were protected from HSV-induced paralysis. Protection was associated with dramatic reductions in recoverable virus, and early expansion of HSV-1-specific CD8 T cells in the regional lymph nodes. Thus, recombinant Lm-expressing Ag from HSV represents a promising new class of vaccines against HSV infection.

  8. Cutting Edge: PD-1 Regulates Imiquimod-Induced Psoriasiform Dermatitis through Inhibition of IL-17A Expression by Innate γδ-Low T Cells.

    PubMed

    Imai, Yasutomo; Ayithan, Natarajan; Wu, Xuesong; Yuan, Ying; Wang, Li; Hwang, Sam T

    2015-07-15

    Programmed cell death 1 (PD-1) is a key regulatory molecule that has been targeted in human cancers, including melanoma. In clinical testing, Abs against PD-1 have resulted in psoriasiform dermatitis (PsD). To determine whether PD-1 regulates PsD, we compared skin responses of PD-1-deficient (PD-1KO) mice and wild-type (WT) controls in an imiquimod (IMQ)-induced murine model of psoriasis. PD-1KO mice showed severe epidermal hyperplasia, greater neutrophilic infiltration, and higher expression of Th17 cytokines (versus WT mice). IMQ exposure increased PD-1 expression by skin γδ-low (GDL) T cells and enhanced expression of PD-L1 by keratinocytes. Three-fold increases in the percentage of IL-17A(+) GDL T cells were observed in skin cell suspensions derived from IMQ-treated PD-1KO mice (versus WT controls), suggesting that the lack of PD-1 has a functional effect not only on αβ T cells, but also on GDL T cells, and that PD-1 may play a regulatory role in PsD.

  9. RoboSimian Cuts Hole in Wall

    NASA Image and Video Library

    2015-06-09

    Using a cordless power drill, RoboSimian cuts a hole into a panel of drywall to complete one of the tasks in the DARPA Robotics Challenge Finals in Pomona, California. This image was taken on June 6, 2015. http://photojournal.jpl.nasa.gov/catalog/PIA19326

  10. Enhanced Cutting Plane Techniques for Bi-Level Optimization Algorithms

    DTIC Science & Technology

    2008-04-28

    28-04-2008) Final Report May 2008 - November 2008 4. TITLE AND SUBTITLE 5a. CONTRACT NUMBER Enhanced Cutting Plane Techniques for Bi-level...determines an optimistic assessment of the costs incurred in the second stage; this assessment is then refined by a set of linear fuictions called cutting ...planes, which provide cause-and-effect relationships between the first- and second-stage decisions. However, these cutting planes are often ineffective

  11. ADVANCED CUTTINGS TRANSPORT STUDY

    SciTech Connect

    Stefan Miska; Nicholas Takach; Kaveh Ashenayi; Mengjiao Yu; Ramadan Ahmed; Mark Pickell; Len Volk; Lei Zhou; Zhu Chen; Aimee Washington; Crystal Redden

    2003-09-30

    The Quarter began with installing the new drill pipe, hooking up the new hydraulic power unit, completing the pipe rotation system (Task 4 has been completed), and making the SWACO choke operational. Detailed design and procurement work is proceeding on a system to elevate the drill-string section. The prototype Foam Generator Cell has been completed by Temco and delivered. Work is currently underway to calibrate the system. Literature review and preliminary model development for cuttings transportation with polymer foam under EPET conditions are in progress. Preparations for preliminary cuttings transport experiments with polymer foam have been completed. Two nuclear densitometers were re-calibrated. Drill pipe rotation system was tested up to 250 RPM. Water flow tests were conducted while rotating the drill pipe up to 100 RPM. The accuracy of weight measurements for cuttings in the annulus was evaluated. Additional modifications of the cuttings collection system are being considered in order to obtain the desired accurate measurement of cuttings weight in the annular test section. Cutting transport experiments with aerated fluids are being conducted at EPET, and analyses of the collected data are in progress. The printed circuit board is functioning with acceptable noise level to measure cuttings concentration at static condition using ultrasonic method. We were able to conduct several tests using a standard low pass filter to eliminate high frequency noise. We tested to verify that we can distinguish between different depths of sand in a static bed of sand. We tested with water, air and a mix of the two mediums. Major modifications to the DTF have almost been completed. A stop-flow cell is being designed for the DTF, the ACTF and Foam Generator/Viscometer which will allow us to capture bubble images without the need for ultra fast shutter speeds or microsecond flash system.

  12. Plasma arc cutting technology: simulation and experiments

    NASA Astrophysics Data System (ADS)

    Cantoro, G.; Colombo, V.; Concetti, A.; Ghedini, E.; Sanibondi, P.; Zinzani, F.; Rotundo, F.; Dallavalle, S.; Vancini, M.

    2011-01-01

    Transferred arc plasma torches are widely used in industrial processes for cutting of metallic materials because of their ability to cut a wide range of metals with very high productivity. The process is characterized by a transferred electric arc established between an electrode inside the torch (the cathode) and another electrode, the metallic workpiece to be cut (the anode). In order to obtain a high quality cut and a high productivity, the plasma jet must be as collimated as possible and must have the higher achievable power density. Plasma modelling and numerical simulation can be very useful tools for the designing and optimizing these devices, but research is still in the making for finding a link between simulation of the plasma arc and a consistent prevision of cut quality. Numerical modelling of the behaviour of different types of transferred arc dual gas plasma torches can give an insight on the physical reasons for the industrial success of various design and process solutions that have appeared over the last years. Diagnostics based on high speed imaging and Schlieren photography can play an important role for investigating piercing, dross generation, pilot arcing and anode attachment location. Also, the behaviour of hafnium cathodes at high current levels at the beginning of their service life can been experimentally investigated, with the final aim of understanding the phenomena that take place during those initial piercing and cutting phases and optimizing the initial shape of the surface of the emissive insert exposed to plasma atmosphere.

  13. ADVANCED CUTTINGS TRANSPORT STUDY

    SciTech Connect

    Troy Reed; Stefan Miska; Nicholas Takach; Kaveh Ashenayi; Gerald Kane; Mark Pickell; Len Volk; Mike Volk; Barkim Demirdal; Affonso Lourenco; Evren Ozbayoglu; Paco Vieira

    2000-10-30

    This is the first quarterly progress report for Year 2 of the ACTS project. It includes a review of progress made in Flow Loop development and research during the period of time between July 14, 2000 and September 30, 2000. This report presents information on the following specific tasks: (a) Progress in Advanced Cuttings Transport Facility design and development (Task 2), (b) Progress on research project (Task 8): ''Study of Flow of Synthetic Drilling Fluids Under Elevated Pressure and Temperature Conditions'', (c) Progress on research project (Task 6): ''Study of Cuttings Transport with Foam Under LPAT Conditions (Joint Project with TUDRP)'', (d) Progress on research project (Task 7): ''Study of Cuttings Transport with Aerated Muds Under LPAT Conditions (Joint Project with TUDRP)'', (e) Progress on research project (Task 9): ''Study of Foam Flow Behavior Under EPET Conditions'', (f) Initiate research on project (Task 10): ''Study of Cuttings Transport with Aerated Mud Under Elevated Pressure and Temperature Conditions'', (g) Progress on instrumentation tasks to measure: Cuttings concentration and distribution (Tasks 11), and Foam properties (Task 12), (h) Initiate a comprehensive safety review of all flow-loop components and operational procedures. Since the previous Task 1 has been completed, we will now designate this new task as: (Task 1S). (i) Activities towards technology transfer and developing contacts with Petroleum and service company members, and increasing the number of JIP members.

  14. ADVANCED CUTTINGS TRANSPORT STUDY

    SciTech Connect

    Troy Reed; Stefan Miska; Nicholas Takach; Kaveh Ashenayi; Mark Pickell; Len Volk, Mike Volk; Lei Zhou; Zhu Chen; Crystal Redden; Aimee Washington

    2002-10-30

    This is the first quarterly progress report for Year-4 of the ACTS Project. It includes a review of progress made in: (1) Flow Loop construction and development and (2) research tasks during the period of time between July 1, 2002 and Sept. 30, 2002. This report presents a review of progress on the following specific tasks: (a) Design and development of an Advanced Cuttings Transport Facility Task 3: Addition of a Cuttings Injection/Separation System, Task 4: Addition of a Pipe Rotation System, (b) New Research project (Task 9b): ''Development of a Foam Generator/Viscometer for Elevated Pressure and Elevated Temperature (EPET) Conditions'', (d) Research project (Task 10): ''Study of Cuttings Transport with Aerated Mud Under Elevated Pressure and Temperature Conditions'', (e) Research on three instrumentation tasks to measure: Cuttings concentration and distribution in a flowing slurry (Task 11), Foam texture while transporting cuttings (Task 12), Viscosity of Foam under EPET (Task 9b). (f) Development of a Safety program for the ACTS Flow Loop. Progress on a comprehensive safety review of all flow-loop components and operational procedures. (Task 1S). (g) Activities towards technology transfer and developing contacts with Petroleum and service company members, and increasing the number of JIP members.

  15. ADVANCED CUTTINGS TRANSPORT STUDY

    SciTech Connect

    Ergun Kuru; Stefan Miska; Nicholas Takach; Kaveh Ashenayi; Gerald Kane; Len Volk; Mark Pickell; Evren Ozbayoglu; Barkim Demirdal; Paco Vieira; Affonso Lourenco

    1999-10-15

    This report includes a review of the progress made in ACTF Flow Loop development and research during 90 days pre-award period (May 15-July 14, 1999) and the following three months after the project approval date (July15-October 15, 1999) The report presents information on the following specific subjects; (a) Progress in Advanced Cuttings Transport Facility design and development, (b) Progress report on the research project ''Study of Flow of Synthetic Drilling Fluids Under Elevated Pressure and Temperature Conditions'', (c) Progress report on the research project ''Study of Cuttings Transport with Foam Under LPAT Conditions (Joint Project with TUDRP)'', (d) Progress report on the research project ''Study of Cuttings Transport with Aerated Muds Under LPAT Conditions (Joint Project with TUDRP)'', (e) Progress report on the research project ''Study of Foam Flow Behavior Under EPET Conditions'', (f) Progress report on the instrumentation tasks (Tasks 11 and 12) (g) Activities towards technology transfer and developing contacts with oil and service company members.

  16. Cutting Edge: Immature human dendritic cells express latency-associated peptide and inhibit T cell activation in a TGF-beta-dependent manner.

    PubMed

    Gandhi, Roopali; Anderson, David E; Weiner, Howard L

    2007-04-01

    Dendritic cells (DCs) play a critical role in both initiating immune responses and in maintaining peripheral tolerance. However, the exact mechanism by which DCs instruct/influence the generation of effector vs regulatory T cells is not clear. In this study, we present evidence that TGF-beta, an important immunoregulatory molecule, is present on the surface of ex vivo immature human DCs bound by latency-associated peptide (LAP). Maturation of DCs upon stimulation with LPS results in loss of membrane-bound LAP and up-regulation of HLA class II and costimulatory molecules. The presence of LAP on immature DCs selectively inhibits Th1 cell but not Th17 cell differentiation and is required for differentiation and/or survival of Foxp3-positive regulatory T cells. Taken together, our results indicate that surface expression of TGF-beta on DCs in association with LAP is one of the mechanisms by which immature DCs limit T cell activation and thus prevent autoimmune responses.

  17. Radial cutting torch

    SciTech Connect

    Robertson, M.C.

    1997-01-08

    The project`s aim is to complete development of the Radial Cutting Torch, a pyrotechnic cutter, for use in all downhole tubular cutting operations in the petroleum industry. Project objectives are to redesign and pressure test nozzle seals to increase product quality, reliability, and manufacturability; improve the mechanical anchor to increase its temperature tolerance and its ability to function in a wider variety of wellbore fluids; and redesign and pressure test the RCT nozzle for operation at pressures from 10 to 20 ksi. The proposal work statement is included in the statement of work for the grant via this reference.

  18. Cutting assembly. [Patent application

    DOEpatents

    Treuhaft, M.B.; Oser, M.S.

    1981-06-25

    A mining auger comprises a cutting head carried at one end of a tubular shaft and a plurality of wall segments which in a first position thereof are disposed side by side around said shaft and in a second position thereof are disposed oblique to said shaft. A vane projects outwardly from each wall segment. When the wall segments are in their first position, the vanes together form a substantially continuous helical wall. A cutter is mounted on the peripheral edge of each of the vanes. When the wall segments are in their second position, the cutters on the vanes are disposed radially outward from the perimeter of the cutting head.

  19. Cryogenic ribbon-cutting

    NASA Image and Video Library

    2011-03-30

    NASA cut the ribbon on a new cryogenics control center at John C. Stennis Space Center on March 30. The new facility is part of a project to strengthen Stennis facilities to withstand the impacts of future storms like hurricane Katrina in 2005. Participants in the ribbon-cutting included (l to r): Jason Zuckerman, director of project management for The McDonnel Group; Keith Brock, director of the NASA Project Directorate at Stennis; Stennis Deputy Director Rick Gilbrech; Steve Jackson of Jacobs Technology; and Troy Frisbie, Cryo Control Center Construction project manager for NASA Center Operations at Stennis.

  20. Cryogenic ribbon-cutting

    NASA Image and Video Library

    2011-03-30

    NASA cut the ribbon on a new cryogenics control center at John C. Stennis Space Center on March 30. The new facility is part of a project to strengthen Stennis facilities to withstand the impacts of future storms like hurricane Katrina in 2005. Participants in the ribbon-cutting included (l to r): Jason Zuckerman, director of project management for The McDonnel Group; Keith Brock, director of the NASA Project Directorate at Stennis; Stennis Deputy Director Rick Gilbrech; Steve Jackson, outgoing program manager of the Jacobs Technology NASA Test Operations Group; and Troy Frisbie, Cryo Control Center Construction project manager for NASA Center Operations at Stennis.

  1. ADVANCED CUTTINGS TRANSPORT STUDY

    SciTech Connect

    Stefan Miska; Troy Reed; Ergun Kuru

    2004-09-30

    The Advanced Cuttings Transport Study (ACTS) was a 5-year JIP project undertaken at the University of Tulsa (TU). The project was sponsored by the U.S. Department of Energy (DOE) and JIP member companies. The objectives of the project were: (1) to develop and construct a new research facility that would allow three-phase (gas, liquid and cuttings) flow experiments under ambient and EPET (elevated pressure and temperature) conditions, and at different angle of inclinations and drill pipe rotation speeds; (2) to conduct experiments and develop a data base for the industry and academia; and (3) to develop mechanistic models for optimization of drilling hydraulics and cuttings transport. This project consisted of research studies, flow loop construction and instrumentation development. Following a one-year period for basic flow loop construction, a proposal was submitted by TU to the DOE for a five-year project that was organized in such a manner as to provide a logical progression of research experiments as well as additions to the basic flow loop. The flow loop additions and improvements included: (1) elevated temperature capability; (2) two-phase (gas and liquid, foam etc.) capability; (3) cuttings injection and removal system; (4) drill pipe rotation system; and (5) drilling section elevation system. In parallel with the flow loop construction, hydraulics and cuttings transport studies were preformed using drilling foams and aerated muds. In addition, hydraulics and rheology of synthetic drilling fluids were investigated. The studies were performed under ambient and EPET conditions. The effects of temperature and pressure on the hydraulics and cuttings transport were investigated. Mechanistic models were developed to predict frictional pressure loss and cuttings transport in horizontal and near-horizontal configurations. Model predictions were compared with the measured data. Predominantly, model predictions show satisfactory agreements with the measured data. As a

  2. The center-cut solution.

    PubMed

    Firnstahl, T W

    1993-01-01

    Timothy Firnstahl owns five successful restaurants in Seattle, but he recently came very close to owning none. In the early 1990s, he found himself, like so many restauranteurs, facing rising costs, inefficient management, and a recession. Confronting financial annihilation, Firnstahl had to act quickly: since he had no peripherals to trim, he cut off the head of his company. Remarkably, it worked. Firnstahl's problem was his new and innovative restaurant, Sharps Fresh Roasting. The heart of the Sharps concept was a unique long-roasting technique that made lean, inexpensive meats taste as juicy and delicious as fattier, expensive cuts. The process also lent itself to faster service and lower labor costs. But it wasn't working. Sharps wasn't breaking even, and his other restaurants couldn't make up the difference. He needed a solution fast. Firnstahl got his answer from Mikhail Gorbachev: slash the centralized command and liberate the company. In doing so, he would also transfer virtually all power and responsibility to his line managers. And after five months of intensive study and planning, he accomplished what he set out to do. He fired most of his corporate staff, empowered his restaurant managers with "100% Power and Responsibility," and, finally, undertook a massive promotion campaign. A year later, Sharps Fresh Roasting is the gold mine Firnstahl always believed it could be. He's done away with bureaucracy and turned business around in a down market. All this because his managers are managing themselves.

  3. Think before You Cut

    ERIC Educational Resources Information Center

    Pettifor, Ann

    2010-01-01

    With the main political parties set on reducing public spending, one might be forgiven for supposing that "savage" cuts are the only way forward. However, the author believes there are alternatives, and that is why public education about the financial system is so important. Today, UK is trying to clear up a mess--a mess made by the…

  4. ADVANCED CUTTINGS TRANSPORT STUDY

    SciTech Connect

    Ergun Kuru; Stefan Miska; Nicholas Takach; Kaveh Ashenayi; Gerald Kane; Len Volk; Mark Pickell; Mike Volk; Barkim Demirdal; Affonso Lourenco; Evren Ozbayoglu; Paco Vieira; Neelima Godugu; Sri Suresh Kumar Thiroveedhula

    2000-04-30

    ACTS flow loop is now operational under elevated pressure and temperature. Currently, experiments with water under pressure and temperature are being conducted. Based on the analysis of Fann 70 data, empirical correlations defining the shear stress as a function of temperature, pressure and the shear rate have been developed for Petrobras synthetic drilling fluids. PVT equipment has been modified for testing Synthetic drilling fluids. Initial calibration tests have been conducted by using water. Currently, the base oil of the Petrobras synthetic drilling fluid is being tested. Foam flow experiments have been conducted. Currently, more experiments are being conducted while data are being analyzed to characterize the rheology of the foam. Cuttings transport experiments have been conducted using air, water and cuttings. Preliminary results have shown that it may not be possible to avoid cuttings bed deposition under any practical combination of air and water flow rates. Foam stability analyses have been conducted. Effects of salt and oil concentration on the foam stability have been investigated. A software for controlling the data sampling and data storage during cuttings monitoring process have been developed.

  5. Cutting Cakes Carefully

    ERIC Educational Resources Information Center

    Hill, Theodore P.; Morrison, Kent E.

    2010-01-01

    This paper surveys the fascinating mathematics of fair division, and provides a suite of examples using basic ideas from algebra, calculus, and probability which can be used to examine and test new and sometimes complex mathematical theories and claims involving fair division. Conversely, the classical cut-and-choose and moving-knife algorithms…

  6. Think before You Cut

    ERIC Educational Resources Information Center

    Pettifor, Ann

    2010-01-01

    With the main political parties set on reducing public spending, one might be forgiven for supposing that "savage" cuts are the only way forward. However, the author believes there are alternatives, and that is why public education about the financial system is so important. Today, UK is trying to clear up a mess--a mess made by the…

  7. A Cut below

    ERIC Educational Resources Information Center

    Lum, Lydia

    2010-01-01

    Today, thousands of California students worry about vanishing college affordability and access, especially for historically under-represented and marginalized populations. The author reports on how students and faculty throughout California are grappling with the effects of draconian state cuts to postsecondary education that have topped more than…

  8. INFINITY ribbon-cutting

    NASA Image and Video Library

    2012-04-11

    Clare Johnston, 10, and Eden Landis, 3, stare in wonder at the moon rock on display at the INFINITY at NASA Stennis Space Center visitor center and museum. The children toured INFINITY exhibits during ribbon-cutting activities for the facility April 11, 2012.

  9. Classroom Cut Ups

    ERIC Educational Resources Information Center

    Lord, Stacy

    2011-01-01

    Discovering identity can be a lifelong challenge for some people, while others seem to figure it out right away. During the middle school years, finding one's identity can be a daunting task. Most students will spend a considerable amount of time during these middle years looking for it. This lesson on cut-paper self-portraits lets students delve…

  10. Cutting Cakes Carefully

    ERIC Educational Resources Information Center

    Hill, Theodore P.; Morrison, Kent E.

    2010-01-01

    This paper surveys the fascinating mathematics of fair division, and provides a suite of examples using basic ideas from algebra, calculus, and probability which can be used to examine and test new and sometimes complex mathematical theories and claims involving fair division. Conversely, the classical cut-and-choose and moving-knife algorithms…

  11. Kids Who Cut.

    ERIC Educational Resources Information Center

    Coy, Doris Rhea; Simpson, Chris

    2002-01-01

    Regardless of whether it is cutting, burning or some other form of self-harm, self-injury is a serious problem requiring serious solutions. This article reviews the various types of self-harm, descriptions of self-mutilators, common myths about self-mutilation, and effective treatment methods. (GCP)

  12. Collaborating To Cut Costs.

    ERIC Educational Resources Information Center

    Strosnider, Kim

    1998-01-01

    Private colleges across the country are collaborating to cut costs, streamline services, and increase efficiency. An ambitious Ohio project, involving 35 colleges, to redesign business operations hopes to save $20-25 million. Other efforts include joint classes using interactive television, shared library resources, cross-registration, jointly…

  13. Electron beam cutting

    DOEpatents

    Mochel, Margaret E.; Humphreys, Colin J.

    1985-04-02

    A method for the cutting of holes 20 Angstroms in diameter, or lines 20 Angstroms wide in a material having positive ionic conduction by the use of a focused electron probe is described. The holes and lines are stable under ambient conditions.

  14. Electron beam cutting

    DOEpatents

    Mochel, M.E.; Humphreys, C.J.

    1985-04-02

    A method for the cutting of holes 20 Angstroms in diameter, or lines 20 Angstroms wide in a material having positive ionic conduction by the use of a focused electron probe is described. The holes and lines are stable under ambient conditions. 2 figs.

  15. Kids Who Cut.

    ERIC Educational Resources Information Center

    Coy, Doris Rhea; Simpson, Chris

    2002-01-01

    Regardless of whether it is cutting, burning or some other form of self-harm, self-injury is a serious problem requiring serious solutions. This article reviews the various types of self-harm, descriptions of self-mutilators, common myths about self-mutilation, and effective treatment methods. (GCP)

  16. Cutting thread at flexible endoscopy.

    PubMed

    Gong, F; Swain, P; Kadirkamanathan, S; Hepworth, C; Laufer, J; Shelton, J; Mills, T

    1996-12-01

    New thread-cutting techniques were developed for use at flexible endoscopy. A guillotine was designed to follow and cut thread at the endoscope tip. A new method was developed for guiding suture cutters. Efficacy of Nd: YAG laser cutting of threads was studied. Experimental and clinical experience with thread-cutting methods is presented. A 2.4 mm diameter flexible thread-cutting guillotine was constructed featuring two lateral holes with sharp edges through which sutures to be cut are passed. Standard suture cutters were guided by backloading thread through the cutters extracorporeally. A snare cutter was constructed to retrieve objects sewn to tissue. Efficacy and speed of Nd: YAG laser in cutting twelve different threads were studied. The guillotine cut thread faster (p < 0.05) than standard suture cutters. Backloading thread shortened time taken to cut thread (p < 0.001) compared with free-hand cutting. Nd: YAG laser was ineffective in cutting uncolored threads and slower than mechanical cutters. Results of thread cutting in clinical studies using sewing machine (n = 77 cutting episodes in 21 patients), in-vivo experiments (n = 156), and postsurgical cases (n = 15 over 15 years) are presented. New thread-cutting methods are described and their efficacy demonstrated in experimental and clinical studies.

  17. ADVANCED CUTTINGS TRANSPORT STUDY

    SciTech Connect

    Troy Reed; Stefan Miska; Nicholas Takach; Kaveh Ashenayi; Mark Pickell; Len Volk; Mike Volk; Lei Zhou; Zhu Chen; Crystal Redden; Aimee Washington

    2003-04-30

    Experiments on the flow loop are continuing. Improvements to the software for data acquisition are being made as additional experience with three-phase flow is gained. Modifications are being made to the Cuttings Injection System in order to improve control and the precision of cuttings injection. The design details for a drill-pipe Rotation System have been completed. A US Patent was filed on October 28, 2002 for a new design for an instrument that can generate a variety of foams under elevated pressures and temperatures and then transfer the test foam to a viscometer for measurements of viscosity. Theoretical analyses of cuttings transport phenomena based on a layered model is under development. Calibrations of two nuclear densitometers have been completed. Baseline tests have been run to determine wall roughness in the 4 different tests sections (i.e. 2-in, 3-in, 4-in pipes and 5.76-in by 3.5-in annulus) of the flow loop. Tests have also been conducted with aerated fluids at EPET conditions. Preliminary experiments on the two candidate aqueous foam formulations were conducted which included rheological tests of the base fluid and foam stability reports. These were conducted after acceptance of the proposal on the Study of Cuttings Transport with Foam Under Elevated Pressure and Elevated Temperature Conditions. Preparation of a test matrix for cuttings-transport experiments with foam in the ACTF is also under way. A controller for instrumentation to measure cuttings concentration and distribution has been designed that can control four transceivers at a time. A prototype of the control circuit board was built and tested. Tests showed that there was a problem with radiated noise. AN improved circuit board was designed and sent to an external expert to verify the new design. The new board is being fabricated and will first be tested with static water and gravel in an annulus at elevated temperatures. A series of viscometer tests to measure foam properties have

  18. The Expressive Arts Project. A Final Report for the Project Period October 1, 1992 - November 30, 1997.

    ERIC Educational Resources Information Center

    Hutinger, Patricia L.

    This report describes the Expressive Arts Project, which was designed to develop and demonstrate a developmentally appropriate, activity-based expressive arts curriculum model, that will enable children with disabilities to have access to activities in the arts that are an accepted part of regular early childhood programs in typical settings. The…

  19. Laser cutting nozzle

    DOEpatents

    Ramos, Terry J.

    1984-01-01

    A laser cutting nozzle for use with a laser cutting apparatus directing a focused beam to a spot on a work piece. The nozzle has a cylindrical body with a conical tip which together have a conically shaped hollow interior with the apex at a small aperture through the tip. The conical hollow interior is shaped to match the profile of the laser beam, at full beamwidth, which passes through the nozzle to the work piece. A plurality of gas inlet holes extend through the body to the hollow interior and are oriented to produce a swirling flow of gas coaxially through the nozzle and out the aperture, aligned with the laser beam, to the work piece. BACKGROUND OF THE INVENTION

  20. Laser cutting nozzle

    DOEpatents

    Ramos, T.J.

    1982-09-30

    A laser cutting nozzle for use with a laser cutting apparatus directing a focused beam to a spot on a work piece. The nozzle has a cylindrical body with a conical tip which together have a conically shaped hollow interior with the apex at a small aperture through the tip. The conical hollow interior is shaped to match the profile of the laser beam, at full beamwidth, which passes through the nozzle to the work piece. A plurality of gas inlet holes extend through the body to the hollow interior and are oriented to produce a swirling flow of gas coaxially through the nozzle and out the aperture, aligned with the laser beam, to the work piece.

  1. Cutting Through Multiyear Ice

    NASA Image and Video Library

    2017-09-27

    ICESCAPE scientists watched from the deck of the Healy as it cut a path through thick multiyear ice on July 6, 2011. Cutting the path is key for getting researchers to remote research sites amid the sea ice. Credit: NASA/Kathryn Hansen The ICESCAPE mission, or "Impacts of Climate on Ecosystems and Chemistry of the Arctic Pacific Environment," is a NASA shipborne investigation to study how changing conditions in the Arctic affect the ocean's chemistry and ecosystems. The bulk of the research took place in the Beaufort and Chukchi seas in summer 2010 and 2011. Credit: NASA/Kathryn Hansen NASA image use policy. NASA Goddard Space Flight Center enables NASA’s mission through four scientific endeavors: Earth Science, Heliophysics, Solar System Exploration, and Astrophysics. Goddard plays a leading role in NASA’s accomplishments by contributing compelling scientific knowledge to advance the Agency’s mission. Follow us on Twitter Like us on Facebook Find us on Instagram

  2. ADVANCED CUTTINGS TRANSPORT STUDY

    SciTech Connect

    Ergun Kuru; Stefan Miska; Nicholas Takach; Kaveh Ashenayi; Gerald Kane; Mark Pickell; Len Volk; Mike Volk; Barkim Demirdal; Affonso Lourenco; Evren Ozbayoglu; Paco Vieira; Neelima Godugu

    2000-07-30

    ACTS flow loop is now operational under elevated pressure and temperature. Currently, experiments with synthetic based drilling fluids under pressure and temperature are being conducted. Based on the analysis of Fann 70 data, empirical correlations defining the shear stress as a function of temperature, pressure and the shear rate have been developed for Petrobras synthetic drilling fluids. PVT equipment has been modified for testing Synthetic oil base drilling fluids. PVT tests with Petrobras Synthetic base mud have been conducted and results are being analyzed Foam flow experiments have been conducted and the analysis of the data has been carried out to characterize the rheology of the foam. Comparison of pressure loss prediction from the available foam hydraulic models and the test results has been made. Cuttings transport experiments in horizontal annulus section have been conducted using air, water and cuttings. Currently, cuttings transport tests in inclined test section are being conducted. Foam PVT analysis tests have been conducted. Foam stability experiments have also been conducted. Effects of salt and oil concentration on the foam stability have been investigated. Design of ACTS flow loop modification for foam and aerated mud flow has been completed. A flow loop operation procedure for conducting foam flow experiments under EPET conditions has been prepared Design of the lab-scale flow loop for dynamic foam characterization and cuttings monitoring instrumentation tests has been completed. The construction of the test loop is underway. As part of the technology transport efforts, Advisory Board Meeting with ACTS-JIP industry members has been organized on May 13, 2000.

  3. Manual bamboo cutting tool.

    PubMed

    Bezerra, Mariana Pereira; Correia, Walter Franklin Marques; da Costa Campos, Fabio Ferreira

    2012-01-01

    The paper presents the development of a cutting tool guide, specifically for the harvest of bamboo. The development was made based on precepts of eco-design and ergonomics, for prioritizing the physical health of the operator and the maintenance of the environment, as well as meet specific requirements of bamboo. The main goal is to spread the use of bamboo as construction material, handicrafts, among others, from a handy, easy assembly and material available tool.

  4. Vortex cutting in superconductors

    NASA Astrophysics Data System (ADS)

    Vlasko-Vlasov, Vitalii K.; Koshelev, Alexei E.; Glatz, Andreas; Welp, Ulrich; Kwok, Wai-K.

    2015-03-01

    Unlike illusive magnetic field lines in vacuum, magnetic vortices in superconductors are real physical strings, which interact with the sample surface, crystal structure defects, and with each other. We address the complex and poorly understood process of vortex cutting via a comprehensive set of magneto-optic experiments which allow us to visualize vortex patterns at magnetization of a nearly twin-free YBCO crystal by crossing magnetic fields of different orientations. We observe a pronounced anisotropy in the flux dynamics under crossing fields and the filamentation of induced supercurrents associated with the staircase vortex structure expected in layered cuprates, flux cutting effects, and angular vortex instabilities predicted for anisotropic superconductors. At some field angles, we find formation of the vortex domains following a type-I phase transition in the vortex state accompanied by an abrupt change in the vortex orientation. To clarify the vortex cutting scenario we performed time-dependent Ginzburg-Landau simulations, which confirmed formation of sharp vortex fronts observed in the experiment and revealed a left-handed helical instability responsible for the rotation of vortices. This work was supported by the U.S. Department of Energy, Office of Science, Materials Sciences and Engineering Division.

  5. Reagan Administration Prepares Budget Cuts.

    ERIC Educational Resources Information Center

    Norman, Colin

    1981-01-01

    Describes tentative federal budget cuts affecting science education in the National Science Foundation, National Aeronautics and Space Administration, Department of Energy, National Institutes of Health, and the specific areas these budget cuts will affect. (DS)

  6. Dealing with Cuts (For Parents)

    MedlinePlus

    ... For Kids For Parents MORE ON THIS TOPIC Cellulitis First Aid: Cuts Staph Infections Bites and Scratches ... Animal Bites Blood Childproofing and Preventing Household Accidents Cellulitis Stitches Scars Cuts, Scratches, and Abrasions What's a ...

  7. ALPS yield optimization cutting program

    Treesearch

    P. Klinkhachorn; J.P. Franklin; Charles W. McMillin; H.A. Huber

    1989-01-01

    This paper reports ongoing work on a series of computer programs developed to automate hardwood lumber processing in a furniture roughmill. The program computes the placement of cuttings on lumber, based on a description of each board in terms of shape and defect location, and a cutting bill. These results are suitable for use with a high-power laser to cut the parts...

  8. CUTTING AND WEDGING JACKET REMOVER

    DOEpatents

    Freedman, M.; Raynor, S.

    1959-04-01

    A tool is presented for stripping cladded jackets from fissionable fuel elements. The tool is a tube which fits closely around the jacket and which has two cutting edges at opposite sides of one end. These cutting edges are adjusted to penetrate only the jacket so that by moving the edges downward the jacket is cut into two pieces.

  9. Knee biomechanics during a jump-cut maneuver: Effects of gender & ACL surgery

    PubMed Central

    Miranda, Daniel L.; Fadale, Paul D.; Hulstyn, Michael J.; Shalvoy, Robert M.; Machan, Jason T.; Fleming, Braden C.

    2012-01-01

    Purpose The purpose of this study was to compare kinetic and knee kinematic measurements from male and female ACL-intact (ACLINT) and ACL-reconstructed (ACLREC) subjects during a jump-cut maneuver using biplanar videoradiography. Methods Twenty subjects were recruited; 10 ACLINT (5 males, 5 females) and 10 ACLREC (4 males, 6 females; five years post surgery). Each subject performed a jump-cut maneuver by landing on a single leg and performing a 45° side-step cut. Ground reaction force was measured by a force plate and expressed relative to body weight. Six-degree-of-freedom knee kinematics were determined from a biplanar videoradiography system and an optical motion capture system. Results ACLINT female subjects landed with a larger peak vertical GRF (p<0.001) compared to ACLINT male subjects. ACLINT subjects landed with a larger peak vertical GRF (p≤0.036) compared to ACLREC subjects. Regardless of ACL reconstruction status, female subjects underwent less knee flexion angle excursion (p=0.002) and had an increased average rate of anterior tibial translation (0.05±0.01%/millisecond; p=0.037) after contact compared to male subjects. Furthermore, ACLREC subjects had a lower rate of anterior tibial translation compared to ACLINT subjects (0.05±0.01%/millisecond; p=0.035). Finally, no striking differences were observed in other knee motion parameters. Conclusion Women permit a smaller amount of knee flexion angle excursion during a jump-cut maneuver, resulting in a larger peak vertical GRF and increased rate of anterior tibial translation. Notably, ACLREC subjects also perform the jump cut maneuver with lower GRF than ACLINT subjects five years post surgery. This study proposes a causal sequence whereby increased landing stiffness (larger peak vertical GRF combined with less knee flexion angle excursion) leads to an increased rate of anterior tibial translation while performing a jump-cut maneuver. PMID:23190595

  10. Maximal cuts in arbitrary dimension

    NASA Astrophysics Data System (ADS)

    Bosma, Jorrit; Sogaard, Mads; Zhang, Yang

    2017-08-01

    We develop a systematic procedure for computing maximal unitarity cuts of multiloop Feynman integrals in arbitrary dimension. Our approach is based on the Baikov representation in which the structure of the cuts is particularly simple. We examine several planar and nonplanar integral topologies and demonstrate that the maximal cut inherits IBPs and dimension shift identities satisfied by the uncut integral. Furthermore, for the examples we calculated, we find that the maximal cut functions from different allowed regions, form the Wronskian matrix of the differential equations on the maximal cut.

  11. Drilling cost-cutting

    SciTech Connect

    Capuano, L.E. Jr.

    1996-12-31

    This presentation by Louis E. Capuano, Jr., President, ThermaSource, Inc., discusses cost-cutting in the drilling phase of geothermal energy exploration and production. All aspects of a geothermal project including the drilling must be streamlined to make it viable and commercial. If production could be maximized from each well, there would be a reduction in drilling costs. This could be achieved in several ways, including big hole and multi-hole completion, directional drilling, better knowledge of the resource and where to penetrate, etc.

  12. ADVANCED CUTTINGS TRANSPORT STUDY

    SciTech Connect

    Stefan Miska; Nicholas Takach; Kaveh Ashenayi

    2004-07-31

    We have tested the loop elevation system. We raised the mast to approximately 25 to 30 degrees from horizontal. All went well. However, while lowering the mast, it moved laterally a couple of degrees. Upon visual inspection, severe spalling of the concrete on the face of the support pillar, and deformation of the steel support structure was observed. At this time, the facility is ready for testing in the horizontal position. A new air compressor has been received and set in place for the ACTS test loop. A new laboratory has been built near the ACTS test loop Roughened cups and rotors for the viscometer (RS300) were obtained. Rheologies of aqueous foams were measured using three different cup-rotor assemblies that have different surface roughness. The relationship between surface roughness and foam rheology was investigated. Re-calibration of nuclear densitometers has been finished. The re-calibration was also performed with 1% surfactant foam. A new cuttings injection system was installed at the bottom of the injection tower. It replaced the previous injection auger. A mechanistic model for cuttings transport with aerated mud has been developed. Cuttings transport mechanisms with aerated water at various conditions were experimentally investigated. A total of 39 tests were performed. Comparisons between the model predictions and experimental measurements show a satisfactory agreement. Results from the ultrasonic monitoring system indicated that we could distinguish between different sand levels. We also have devised ways to achieve consistency of performance by securing the sensors in the caps in exactly the same manner as long as the sensors are not removed from the caps. A preliminary test was conducted on the main flow loop at 100 gpm flow rate and 20 lb/min cuttings injection rate. The measured bed thickness using the ultrasonic method showed a satisfactory agreement with nuclear densitometer readings. Thirty different data points were collected after the test

  13. INFINITY ribbon-cutting

    NASA Image and Video Library

    2012-04-11

    Ceremony participants prepare to cut the ribbon on the INFINITY at NASA Stennis Space Center facility April 11, 2012. Participating in the ceremony were (l to r): Gulfport Mayor and INFINITY Science Center Inc. Chairman George Schloegel; U.S. Rep. Steven Palazzo, R-Miss.; U.S. Sen. Roger Wicker, R-Miss.; Roy S. Estess granddaughter Lauren McKay; Mississippi Gov. Phil Bryant; Leo Seal Jr. grandson Leo Seal IV; Stennis Director Patrick Scheuermann; U.S. Sen. Thad Cochran, R-Miss.; NASA Chief of Staff David Radzanowski; and Apollo 13 astronaut and INFINITY Science Center Inc. Vice Chairman Fred Haise.

  14. Photochemical cutting of fabrics

    DOEpatents

    Piltch, Martin S.

    1994-01-01

    Apparatus for the cutting of garment patterns from one or more layers of fabric. A laser capable of producing laser light at an ultraviolet wavelength is utilized to shine light through a pattern, such as a holographic phase filter, and through a lens onto the one or more layers of fabric. The ultraviolet laser light causes rapid photochemical decomposition of the one or more layers of fabric, but only along the pattern. The balance of the fabric of the one or more layers of fabric is undamaged.

  15. Cross-Cutting Faults

    NASA Technical Reports Server (NTRS)

    2005-01-01

    16 May 2005 This Mars Global Surveyor (MGS) Mars Orbiter Camera (MOC) image shows cross-cutting fault scarps among graben features in northern Tempe Terra. Graben form in regions where the crust of the planet has been extended; such features are common in the regions surrounding the vast 'Tharsis Bulge' on Mars.

    Location near: 43.7oN, 90.2oW Image width: 3 km (1.9 mi) Illumination from: lower left Season: Northern Summer

  16. Cross-Cutting Faults

    NASA Technical Reports Server (NTRS)

    2005-01-01

    16 May 2005 This Mars Global Surveyor (MGS) Mars Orbiter Camera (MOC) image shows cross-cutting fault scarps among graben features in northern Tempe Terra. Graben form in regions where the crust of the planet has been extended; such features are common in the regions surrounding the vast 'Tharsis Bulge' on Mars.

    Location near: 43.7oN, 90.2oW Image width: 3 km (1.9 mi) Illumination from: lower left Season: Northern Summer

  17. Occupational exposure to dioxins by thermal oxygen cutting, welding, and soldering of metals.

    PubMed

    Menzel, H M; Bolm-Audorff, U; Turcer, E; Bienfait, H G; Albracht, G; Walter, D; Emmel, C; Knecht, U; Päpke, O

    1998-04-01

    This paper focuses on one aspect of occupational dioxin exposure that is novel and unexpected. Exposures in excess of the German threshold limit value of 50 pg international toxicity equivalent (I-TEQ)/m3 are very frequent, unpredictable, and sometimes very high--up to 6612 pg I-TEQ/m3--during thermal oxygen cutting at scrap metal and demolition sites. The same procedure involving virgin steel in steel trade and mass production of steel objects gave no such evidence, even though no final conclusions can be drawn because of the low number of samples analyzed. Low dioxin exposures during inert gas electric arc welding confirm previous literature findings, whereas soldering and thermal oxygen cutting in the presence of polyvinyl chloride give rise to concern. The consequences of occupational dioxin exposure were studied by analysis of the dioxin-blood concentration, the body burden, of men performing thermal oxygen cutting at scrap metal reclamation and demolition sites, in steel trade and producing plants as well as for industrial welders and white-collar workers. The results concerning body burdens are in excellent agreement with the dioxin exposure as characterized by dioxin air concentration in the workplace. The significant positive correlation between duration and frequency of performing thermal oxygen cutting at metal reclamation and demolition sites expressed in job-years and dioxin body burden speaks for the occupational origin of the observed overload after long times. The results reported here lead to consequences for occupational health, which are discussed and require immediate attention.

  18. Organ-specific gene expression in maize: The P-wr allele. Final report, August 15, 1993--August 14, 1996

    SciTech Connect

    Peterson, T.A.

    1997-06-01

    The ultimate aim of our work is to understand how a regulatory gene produces a specific pattern of gene expression during plant development. Our model is the P-wr gene of maize, which produces a distinctive pattern of pigmentation of maize floral organs. We are investigating this system using a combination of classical genetic and molecular approaches. Mechanisms of organ-specific gene expression are a subject of intense research interest, as it is the operation of these mechanisms during eukaryotic development which determine the characteristics of each organism Allele-specific expression has been characterized in only a few other plant genes. In maize, organ-specific pigmentation regulated by the R, B, and Pl genes is achieved by differential transcription of functionally conserved protein coding sequences. Our studies point to a strikingly different mechanism of organ-specific gene expression, involving post-transcriptional regulation of the regulatory P gene. The novel pigmentation pattern of the P-wr allele is associated with differences in the encoded protein. Furthermore, the P-wr gene itself is present as a unique tandemly amplified structure, which may affect its transcriptional regulation.

  19. Cutting Plane Algorithms for Maximum Problems

    DTIC Science & Technology

    1991-12-01

    Bazaraa and Shetty (1979). For variational inequalities, references on the cutting plane approach are considerably less. Zuhovickii et al. (1969) (see...and can be expressed as a convex combination of a finite number of extreme points [see, e.g., Bazaraa et al., (1990)], For VI problems, both U and X are...unique solution (see, page 234 of Bazaraa and Shetty, 1979)., 32 Figure 4: A ’Strong’ Solution to a Variational Inequality Problem The rate of

  20. Vibrator improves spark erosion cutting process

    NASA Technical Reports Server (NTRS)

    Thrall, L. R.

    1966-01-01

    Variable frequency mechanical vibrator improves spark erosion cutting process. The vibration of the cutting tip permits continual flushing away of residue around the cut area with nondestructive electric transformer oil during the cutting process.

  1. Study on roadheader cutting load at different properties of coal and rock.

    PubMed

    Li, Xueyi; Huang, Binbing; Ma, Guoying; Zeng, Qingliang

    2013-01-01

    The mechanism of cutting process of roadheader with cutting head was researched, and the influences of properties of coal and rock on cutting load were deeply analyzed. Aimed at the defects of traditional calculation method of cutting load on fully expressing the complex cutting process of cutting head, the method of finite element simulation was proposed to simulate the dynamic cutting process. Aimed at the characteristics of coal and rock which affect the cutting load, several simulations with different firmness coefficient were taken repeatedly, and the relationship between three-axis force and firmness coefficient was derived. A comparative analysis of cutting pick load between simulation results and theoretical formula was carried out, and a consistency was achieved. Then cutting process with a total cutting head was carried out on this basis. The results show that the simulation analysis not only provides a reliable guarantee for the accurate calculation of the cutting head load and improves the efficiency of the cutting head cutting test but also offers a basis for selection of cutting head with different geological conditions of coal or rock.

  2. Study on Roadheader Cutting Load at Different Properties of Coal and Rock

    PubMed Central

    2013-01-01

    The mechanism of cutting process of roadheader with cutting head was researched, and the influences of properties of coal and rock on cutting load were deeply analyzed. Aimed at the defects of traditional calculation method of cutting load on fully expressing the complex cutting process of cutting head, the method of finite element simulation was proposed to simulate the dynamic cutting process. Aimed at the characteristics of coal and rock which affect the cutting load, several simulations with different firmness coefficient were taken repeatedly, and the relationship between three-axis force and firmness coefficient was derived. A comparative analysis of cutting pick load between simulation results and theoretical formula was carried out, and a consistency was achieved. Then cutting process with a total cutting head was carried out on this basis. The results show that the simulation analysis not only provides a reliable guarantee for the accurate calculation of the cutting head load and improves the efficiency of the cutting head cutting test but also offers a basis for selection of cutting head with different geological conditions of coal or rock. PMID:24302866

  3. Vortex cutting in superconductors

    NASA Astrophysics Data System (ADS)

    Glatz, A.; Vlasko-Vlasov, V. K.; Kwok, W. K.; Crabtree, G. W.

    2016-08-01

    Vortex cutting and reconnection is an intriguing and still-unsolved problem central to many areas of classical and quantum physics, including hydrodynamics, astrophysics, and superconductivity. Here, we describe a comprehensive investigation of the crossing of magnetic vortices in superconductors using time dependent Ginsburg-Landau modeling. Within a macroscopic volume, we simulate initial magnetization of an anisotropic high temperature superconductor followed by subsequent remagnetization with perpendicular magnetic fields, creating the crossing of the initial and newly generated vortices. The time resolved evolution of vortex lines as they approach each other, contort, locally conjoin, and detach, elucidates the fine details of the vortex-crossing scenario under practical situations with many interacting vortices in the presence of weak pinning. Our simulations also reveal left-handed helical vortex instabilities that accompany the remagnetization process and participate in the vortex crossing events.

  4. Cut By Troughs

    NASA Technical Reports Server (NTRS)

    2005-01-01

    1 September 2005 This Mars Global Surveyor (MGS) Mars Orbiter Camera (MOC) image shows an impact crater cut by troughs which formed after the crater formed. The crater and troughs have large windblown ripples on their floors. The ripples, troughs, craters, and other surfaces in this scene have all been mantled by dust. Dark streaks on slopes indicate areas where avalanches of dry dust have occurred. These features are located on Sacra Mena, a large mesa in the Kasei Valles region.

    Location near: 25.4oN, 66.8oW Image width: width: 3 km (1.9 mi) Illumination from: lower left Season: Northern Autumn

  5. Cutting ice: nanowire regelation.

    PubMed

    Hynninen, Teemu; Heinonen, Vili; Dias, Cristiano L; Karttunen, Mikko; Foster, Adam S; Ala-Nissila, Tapio

    2010-08-20

    Even below its normal melting temperature, ice melts when subjected to high pressure and refreezes once the pressure is lifted. A classic demonstration of this regelation phenomenon is the passing of a thin wire through a block of ice when sufficient force is exerted. Here we present a molecular-dynamics study of a nanowire cutting through ice to unravel the molecular level mechanisms responsible for regelation. In particular, we show that the transition from a stationary to a moving wire due to increased driving force changes from symmetric and continuous to asymmetric and discontinuous as a hydrophilic wire is replaced by a hydrophobic one. This is explained at the molecular level in terms of the wetting properties of the wire.

  6. Cross-Cutting Relationships

    NASA Technical Reports Server (NTRS)

    2003-01-01

    [figure removed for brevity, see original site]

    Released 25 August 2003

    The several linear cross-cutting grabens and collapse features observed in this THEMIS image illustrate the relative timing of a series of complex geologic processes as more recent events produce features that overlap and intersect older ones. Some impact craters are observed to be cut grabens, suggesting an older impact event compared to impact craters that appear fresh and unmodified.

    Image information: VIS instrument. Latitude 14.1, Longitude 236.3 East (123.7 West). 19 meter/pixel resolution.

    Note: this THEMIS visual image has not been radiometrically nor geometrically calibrated for this preliminary release. An empirical correction has been performed to remove instrumental effects. A linear shift has been applied in the cross-track and down-track direction to approximate spacecraft and planetary motion. Fully calibrated and geometrically projected images will be released through the Planetary Data System in accordance with Project policies at a later time.

    NASA's Jet Propulsion Laboratory manages the 2001 Mars Odyssey mission for NASA's Office of Space Science, Washington, D.C. The Thermal Emission Imaging System (THEMIS) was developed by Arizona State University, Tempe, in collaboration with Raytheon Santa Barbara Remote Sensing. The THEMIS investigation is led by Dr. Philip Christensen at Arizona State University. Lockheed Martin Astronautics, Denver, is the prime contractor for the Odyssey project, and developed and built the orbiter. Mission operations are conducted jointly from Lockheed Martin and from JPL, a division of the California Institute of Technology in Pasadena.

  7. Cross-Cutting Relationships

    NASA Technical Reports Server (NTRS)

    2003-01-01

    [figure removed for brevity, see original site]

    Released 25 August 2003

    The several linear cross-cutting grabens and collapse features observed in this THEMIS image illustrate the relative timing of a series of complex geologic processes as more recent events produce features that overlap and intersect older ones. Some impact craters are observed to be cut grabens, suggesting an older impact event compared to impact craters that appear fresh and unmodified.

    Image information: VIS instrument. Latitude 14.1, Longitude 236.3 East (123.7 West). 19 meter/pixel resolution.

    Note: this THEMIS visual image has not been radiometrically nor geometrically calibrated for this preliminary release. An empirical correction has been performed to remove instrumental effects. A linear shift has been applied in the cross-track and down-track direction to approximate spacecraft and planetary motion. Fully calibrated and geometrically projected images will be released through the Planetary Data System in accordance with Project policies at a later time.

    NASA's Jet Propulsion Laboratory manages the 2001 Mars Odyssey mission for NASA's Office of Space Science, Washington, D.C. The Thermal Emission Imaging System (THEMIS) was developed by Arizona State University, Tempe, in collaboration with Raytheon Santa Barbara Remote Sensing. The THEMIS investigation is led by Dr. Philip Christensen at Arizona State University. Lockheed Martin Astronautics, Denver, is the prime contractor for the Odyssey project, and developed and built the orbiter. Mission operations are conducted jointly from Lockheed Martin and from JPL, a division of the California Institute of Technology in Pasadena.

  8. Final Report Construction of Whole Genome Microarrays, and Expression Analysis of Desulfovibrio vulgaris cells in Metal-Reducing Conditions

    SciTech Connect

    M.W. Fields; J.D. Wall; J. Keasling; J. Zhou

    2008-05-15

    experimental results, a set of criteria were suggested for the design of gene-specific and group-specific oligonucleotide probes, and these criteria should provide valuable information for the development of new software and algorithms for microarray-based studies. Secondly, in order to empirically determine the effect of probe length on signal intensities, microarrays with oligonucleotides of different lengths were used to monitor gene expression at a whole genome level. To determine what length of oligonucleotide is a better alternative to PCR-generated probes, the performance of oligonucleotide probes was systematically compared to that of their PCR-generated counterparts for 96 genes from Shewanella oneidensis MR-1 in terms of overall signal intensity, numbers of detected genes, specificity, sensitivity and differential gene expression under experimental conditions. Hybridizations conducted at 42 C, 45 C, 50 C, and 60 C indicated that good sensitivities were obtained at 45 C for oligonucleotide probes in the presence of 50% formamide, under which conditions specific signals were detected by both PCR and oligonucleotide probes. Signal intensities increased as the length of oligonucleotide probes increased, and the 70mer oligonucleotide probes produced similar signal intensities and detected a similar number of ORFs compared to the PCR probes. cDNA, 70mer, 60mer and 50mer arrays had detection sensitivities at 5.0, 25, 100 and 100 ng of genomic DNA, or an approximately equivalent of 1.9 x 10{sup 6}, 9.2 x 10{sup 6}, 3.7 x 10{sup 7} and 3.7 x 10{sup 7} copies, respectively when the array was hybridized with genomic DNA. To evaluate differential gene expression under experimental conditions, S. oneidensis MR-1 cells were exposed to low or high pH conditions for 30 and 60 min, and the transcriptional profiling detected by oligonucleotide probes (50mer, 60mer, and 70mer) was closely correlated with that detected by the PCR probes. The results demonstrated that 70mer

  9. Mechanically cut mitotic spindles: clean cuts and stable microtubules.

    PubMed

    Nicklas, R B; Lee, G M; Rieder, C L; Rupp, G

    1989-11-01

    We have discovered an easy way to cut through the mitotic spindle at any desired place. Spindles of demembranated cricket or grasshopper spermatocytes were severed with a microneedle between the chromosomes and one pole, and the cut-off polar piece was swept away. Spindle structure and microtubule dynamics in cut spindles were studied by anti-tubulin immunostaining and electron microscopy. The cut is clean: all microtubules are severed and only a few extend beyond the others. This provides the basis for a clear test of whether traction fibers pull chromosomes to the pole in anaphase, because the putative traction fiber is cleanly severed. Cutting creates new plus ends on microtubules in the cut-off polar piece and new minus ends on microtubules in the main spindle body. The microtubules with new plus ends are unstable, as expected from the dynamic instability of microtubules. However, the microtubules with new minus ends are as stable as uncut microtubules in the same spindle. Our mechanical method of cutting microtubules very likely creates native, reactive ends, and therefore the surprising stability of new minus ends is genuinely interesting, not an artifact of cutting.

  10. Genetic parameters for carcass cut weight in Irish beef cattle.

    PubMed

    Pabiou, T; Fikse, W F; Näsholm, A; Cromie, A R; Drennan, M J; Keane, M G; Berry, D P

    2009-12-01

    The objective of this study was to estimate genetic parameters for the weights of different wholesale cuts, using an experimental and a commercial data set. The experimental and commercial data sets included 413 and 635 crossbred Belgian Blue, Charolais, Limousin, Angus, Holstein, and Simmental animals, respectively. Univariate analyses using a mixed linear animal model with relationships were undertaken to estimate the heritability of cold carcass weight, carcass conformation and fat, and the cut weights, whereas a series of bivariate analyses was used to estimate the phenotypic and genetic correlations between carcass weight, carcass conformation, carcass fat, and the major primal cuts. Heritability estimates for cold carcass weight in both data sets were moderate (>0.48), whereas heritability estimates for carcass conformation and fat grading were greater in the commercial data set (>0.63) than in the experimental study (>0.33). Across both data sets, heritability estimates for wholesale cut weight in the forequarter varied from 0.03 to 0.79, whereas heritability estimates of carcass cut weight in the hindquarter varied from 0.14 to 0.86. Heritability estimates for cut weights expressed as a proportion of the entire carcass weight varied from 0.04 to 0.91. Genetic correlations were strong among the different carcass cut weights within the experimental and the commercial studies. Genetic correlations between the weights of selected carcass cuts and carcass weight were moderate to high (minimum 0.45; maximum 0.88) in both data sets. Positive genetic correlations were observed in the commercial data set between the different wholesale cut weights and carcass conformation, whereas these were positive and negative in the experimental data set. Selection for increased carcass weight will, on average, increase the weight of each cut. However, the genetic correlations were less than unity, suggesting a benefit of more direct selection on high value cuts.

  11. Silvicultural aspects intermediate cuttings

    Treesearch

    Kenneth L. Carvell

    1971-01-01

    Correct timing of the first thinning in mixed oak stands depends largely on the composition and condition of the stands and on available markets for small wood products. Delaying first thinnings in high-quality seedling-origin stands until a long, straight, clear bole has developed is of primary importance in assuring high quality of the final crop trees. However, many...

  12. Genetic characterization of Lophopyrum elongatum salt tolerance and associated ion regulation as expressed in bread wheat. Final technical report

    SciTech Connect

    1997-10-07

    Lophopyrum elongatum is a highly salt-tolerant relative of wheat. Its salt tolerance is partially expressed in the amphiploid from a cross between wheat cv. Chinese Spring and L. elongatum. Genetic studies showed that the tolerance of gradually imposed salt stress is controlled by L. elongatum chromosomes 3E, 4E, 5E, and 7E and the tolerance of suddenly imposed salt stress by chromosomes 3E, 5E, 6E, and 7E. In wheat, rye, barley, and Dasypyrum, chromosomes of the same homoeologous groups, 3, 5, 6, and 7, were found to control the tolerance of these stress regimes. To gain insight into the physiological mechanisms of salt tolerance by wheat and L. elongatum, accumulation of Na and K, 20 protein amino acids, glycinebetaine, aminobutyrate, all TCA cycle intermediates, oxalate, glycerol-3-P, glyceraldehyde-3-P, pyruvate, lactate, ornithine, taurine, glucose, sucrose and other sugars was examined in the amphiploid and Chinese Spring by gas chromatography and H-NMR.

  13. Improvement Cutting in Bottomland Hardwoods

    Treesearch

    J. W. Johnson

    1951-01-01

    Do bottomland hardwood forests respond to improvement cuts? Do growth rate and stand quality increase enough to make up for the extra effort and, sometimes, outright expense of improvement cutting? Ten years of growth on some plots on the Delta Experimental Forest near Stoneville, Mississippi, indicates that the answer to both questions is "yes".

  14. Composite structure for cutting tools

    SciTech Connect

    Radd, F.J.; Haden, E.L.

    1984-01-01

    A cutting tool comprises a compact bundle of elongated, substantially cylindrical fibers or rods formed from a cemented metal carbide material. The bundle of fibers is shrink-fitted within a metal collar to form a long-wearing cutting tool.

  15. Corner-cutting mining assembly

    DOEpatents

    Bradley, John A.

    1983-01-01

    A mining assembly includes a primary rotary cutter mounted on one end of a support shaft and four secondary rotary cutters carried on the same support shaft and positioned behind the primary cutters for cutting corners in the hole cut by the latter.

  16. How to Cut Publications Costs.

    ERIC Educational Resources Information Center

    Carter, Virginia L., Ed.; Alberger, Patricia A., Ed.

    This handbook on how to cut costs in college publications contains the following articles: "Stretching Your Publications Dollar: The Basics," by Kelvin J. Arden and William J. Whalen; "How to Print Cheaper," by M. Frederic Volkmann; "How Your Colleagues Cut Costs," by Robert S. Topor; "Printing Specifications: Writing Them Right," by M. Frederic…

  17. Minimum Cuts and Related Problems.

    DTIC Science & Technology

    The paper is concerned with an integer programming characterization of a cut in a network. This characterization provides a fundamental equivalence...between directed pseudosummetric networks and undirected networks. It also identifies a class of problems which can be solved as minimum cut problems on a network. (Author)

  18. Cutting Head for Ultrasonic Lithotripsy

    NASA Technical Reports Server (NTRS)

    Angulo, Earl D. (Inventor); Goodfriend, Roger (Inventor)

    1989-01-01

    A cutting head for attachment to the end of the wire probe of an ultrasonic kidney stone disintegration instrument. The cutting head has a plurality of circumferentially arranged teeth formed at one end thereof to provide a cup-shaped receptacle for kidney stones encountered during the disintegration procedure. An integral reduced diameter collar diminishes stress points in the wire and reduces breakage thereof.

  19. Cutting and Self-Harm

    MedlinePlus

    ... sad Cutting and self-harm Cutting and self-harm Self-harm, sometimes called self-injury, is when a person ... about how one girl helps herself not self-harm. What are signs of self-injury in others? ...

  20. Dominus for cut flower production

    USDA-ARS?s Scientific Manuscript database

    Fumigation with methyl bromide was the principal method of soilborne pest control in cut flower production. Many cut flower growers in Florida have ceased production, but those that remain are restricted in the fumigants that they are able to utilize due to proximity to potable water sources and oc...

  1. How to Cut Publications Costs.

    ERIC Educational Resources Information Center

    Carter, Virginia L., Ed.; Alberger, Patricia A., Ed.

    This handbook on how to cut costs in college publications contains the following articles: "Stretching Your Publications Dollar: The Basics," by Kelvin J. Arden and William J. Whalen; "How to Print Cheaper," by M. Frederic Volkmann; "How Your Colleagues Cut Costs," by Robert S. Topor; "Printing Specifications: Writing Them Right," by M. Frederic…

  2. Tubing and cable cutting tool

    NASA Technical Reports Server (NTRS)

    Mcsmith, D. D.; Richardson, J. I. (Inventor)

    1984-01-01

    A hand held hydraulic cutting tool was developed which is particularly useful in deactivating ejection seats in military aircraft rescue operations. The tool consists primarily of a hydraulic system composed of a fluid reservoir, a pumping piston, and an actuator piston. Mechanical cutting jaws are attached to the actuator piston rod. The hydraulic system is controlled by a pump handle. As the pump handle is operated the actuator piston rod is forced outward and thus the cutting jaws are forced together. The frame of the device is a flexible metal tubing which permits easy positioning of the tool cutting jaws in remote and normally inaccessible locations. Bifurcated cutting edges ensure removal of a section of the tubing or cable to thereby reduce the possibility of accidental reactivation of the tubing or cable being severed.

  3. Cut-constructible part of QCD amplitudes

    SciTech Connect

    Britto, Ruth; Feng Bo; Mastrolia, Pierpaolo

    2006-05-15

    Unitarity cuts are widely used in analytic computation of loop amplitudes in gauge theories such as QCD. We expand upon the technique introduced in hep-ph/0503132 to carry out any finite unitarity cut integral. This technique naturally separates the contributions of bubble, triangle and box integrals in one-loop amplitudes and is not constrained to any particular helicity configurations. Loop momentum integration is reduced to a sequence of algebraic operations. We discuss the extraction of the residues at higher-order poles. Additionally, we offer concise algebraic formulas for expressing coefficients of three-mass triangle integrals. As an application, we compute all remaining coefficients of bubble and triangle integrals for nonsupersymmetric six-gluon amplitudes.

  4. Cut Order Planning. Short Term Task, Final Report

    DTIC Science & Technology

    1991-05-01

    1 54.19 7707 2 1 71.41 09 3 2 1 71.86 10 2 67.26* * 711 _____3 3 1________ 71.19 7121 3 68.02_ 713 3 1 11 68.27 ____ - 714 31 1 1 i 68.52 ___ 715 3...Denote public availability or limitation. Cite Block 2 . Reoort Date. Full publication date any availability to the public. Enter additional including day...See authorities the part of the report that provides the most NASA - See Handbook NHB 2200.2. meaningful and complete information. When a NTIS - Leave

  5. Countdown Clock Ribbon Cutting

    NASA Image and Video Library

    2016-03-01

    Kennedy Space Center Director Bob Cabana speaks at the dedication of the newest display at the entrance to the center's visitor complex. The historic countdown clock was originally set up at the space center's Press Site and was used from the launch of Apollo 12 on Nov. 14, 1969 to the final space shuttle mission, STS-135, launched on July 8, 2011. The old countdown clock was replaced in 2014 with a modern light emitting diode, or LED, display.

  6. Countdown Clock Ribbon Cutting

    NASA Image and Video Library

    2016-03-01

    The newest display at the Kennedy Space Center Visitor Complex is the spaceport's historic countdown clock. It is now located at the entrance to the visitor complex. The clock was set up at the space center's Press Site and used from the launch of Apollo 12 on Nov. 14, 1969 to the final space shuttle mission, STS-135, launched on July 8, 2011. The old countdown clock was replaced in 2014 with a modern light emitting diode, or LED, display.

  7. Water-jet-assist cutting evaluation and cutting trials. Research report (Final)

    SciTech Connect

    Neumann, U.

    1991-10-29

    Mining coal using the longwall method is becoming increasingly popular in the United States. Unfortunately, the dust levels liberated by various longwall equipment can exceed the permissible limits and therefore reduce the productivity. In 1984, the Eickhoff Corporation was awarded Contract no. J0145039 to build and demonstrate a water-jet-assisted shearer for the multiple purpose of reducing the dust levels, increasing the material size, and improving the bit service life. Two shearers were built, of which one was operated for two panels in a United States mine. Dust measurements and bit wear measurements were conducted and included in the report. The levels of the respirable dust were reduced by up to 52% and the service life of the bits was increased due to the cooling and lubricating effect of the water jets.

  8. Muscle profiling to improve the value of retail meat cuts.

    PubMed

    Jung, E Y; Hwang, Y H; Joo, S T

    2016-10-01

    Nutrition and meat quality are always important to consumers, but vary by individual muscle or muscle groups in retail meat cuts. Muscle profiling of nutrient content and palatability for all retail beef cuts is necessary to suggest healthy and tasty beef cuts and to inform consumers of the benefits of beef consumption. The current paper reviews numerous studies that provide muscle profiles for nutrients and palatability attributes of muscles or muscle groups in retail beef cuts. The composition of nutrients including protein, fat, moisture, vitamins, and minerals in beef cuts is documented as well as the nutritive role as a part of a healthy diet. In addition, this review presents knowledge in relation to innovative carcass fabrication and value-added cuts to improve the value of beef carcass. Finally, the current work emphasize the palatability assessment of individual beef muscles, and concludes that all retail beef cuts should be merchandised for proper cooking according to the palatability profiles of beef muscles. Copyright © 2016 Elsevier Ltd. All rights reserved.

  9. Polyphasic characterization of bacterial community in fresh cut salads.

    PubMed

    Randazzo, Cinzia Lucia; Scifò, Giovanna Ombretta; Tomaselli, Filippo; Caggia, Cinzia

    2009-01-15

    In the present work we describe a polyphasic study of bacterial community in fresh cut salads packaged under ordinary and modified atmospheres. Samples of fresh cut salads were aseptically collected at 0, 3, and 6 days of storage and analysed both by culture-dependent and -independent methods. DNA extracted from fresh cut salad samples was used as a template for PCR amplification of 16 S rRNA gene; the PCR products were analyzed by denaturing gradient gel electrophoresis (DGGE); finally, clone libraries of 16 S rRNA gene from the fresh cut salad was constructed. Results of plating count revealed a significant increase of all microbial loads in fresh-cut salad samples packaged in OA and that the microbial growth of the different groups was significantly affected by the conditions applied for MA packaging. A constant presence, throughout storage, of the pathogenic bacteria in all the fresh-cut salads samples was highlighted by PCR-DGGE analysis. Therefore, the polyphasic approach used in the present study allowed us to characterize the main species involved in the fresh cut salad products and to better understand their dynamics throughout storage.

  10. Doubly Rotated Cut SAW Devices.

    DTIC Science & Technology

    1982-01-01

    A O-AIIO 663 NOTO AOI.A INC SCOTTS A LEJ AZ S0V RNmF.NT ELECTRONICS DV F/S WI1 DOUBLY ROTATED CUT SAV DEVICES.(U) JAN 82 D F WIL.IANMS F T CHO DAK20...quartz substrates for the purpose of locating promising angular ranges with properties superior to the singly rotated cuts now in existence More...detailed calculations follow to refine the angular coordinates in order to specify cuts for experimental erification in Task I1. In Task II, sets of

  11. Doubly Rotated Cut SAW Devices.

    DTIC Science & Technology

    1981-04-01

    AD-AO 545 MOTOROLA INC SCOTTSDALE AZ GOVERNMENT ELECTRONICS DIV F/O 20/2 DOUBLY ROTATED CUT SAW DEVICES.( U) APR 81 0 F WILLIAMS, F Y CHO DAAK2O 79...f we Ma. he0 _TL ft . *VM or seu3f? 6 090100 cove mis interim Report.~arch 198 ’ Doubly Rotated Cut SAW Devices .r etme 9 9. SInFY T ON 6MNY mUUUUf L...exploratory development of doubly rotated cuts of quartz possessing superior Surface Acoustic Wave (SAW) properties for applications involving

  12. Doubly Rotated Cut SAW Devices.

    DTIC Science & Technology

    1981-08-01

    A0-AI03 -728 MOTOROLA INC SCOTTSDALE AZ GOVERNMENT ELECTRONICS DIV FIG 20/2 DOUBLY ROTATED CUT SAW DEVICES. U P AUG 81 0 F WILLIAMS, F Y CHO OAAK20...79-C-0275 UNCLASSIFIED DELET-TR-79-0275-3 ML wIIIIIIIIIIIIIIIIIIIIIII illlllllllllr: K8 MMR UNCLASSIFIED / JZ R-79-0273 Doubly Rotated Cut SAW Devices...towme. e *#* tooeeeimp md fallp p, uh9lbme The objective of this program is the exploratory development of doubly rotated cuts of quartz possessing

  13. Cutting Head for Ultrasonic Lithotripsy

    NASA Technical Reports Server (NTRS)

    Angulo, E. D.; Goodfriend, R.

    1987-01-01

    Kidney stones lodged in urinary tract disintegrated with increased safety and efficiency by cutting head attached to end of vibrated wire probe. Aligns probe with stone and enables probe to vibrate long enough to disintegrate stone. Design of cutting head reduces risk of metal-fatigue-induced breakage of probe tip leaving metal fragments in urinary tract. Teeth of cutting head both seat and fragment kidney stone, while extension of collar into catheter lessens mechanical strain in probe wire, increasing probe life and lessening danger of in situ probe breakage.

  14. Countdown Clock Ribbon Cutting

    NASA Image and Video Library

    2016-03-01

    Kennedy Space Center Director Bob Cabana, left, and Therrin Protze, chief operating officer of Kennedy's Visitor Complex, celebrate the dedication of the spaceport's historic countdown clock as the newest display at the center's visitor complex. Now located at the entrance to the visitor complex, the spaceport's historic countdown clock was used starting with the launch of Apollo 12 on Nov. 14, 1969. Originally set up at the space center's Press Site, the clock operated through the final space shuttle mission, STS-135, launched on July 8, 2011. The old countdown clock was replaced in 2014 with a modern light emitting diode, or LED, display.

  15. Countdown Clock Ribbon Cutting

    NASA Image and Video Library

    2016-03-01

    Therrin Protze, chief operating officer of the Kennedy Space Center Visitor Complex, speaks at the dedication of the center's historic countdown clock. To the right is space center director Bob Cabana. Now located at the entrance to the visitor complex, the spaceport's historic countdown clock was used starting with the launch of Apollo 12 on Nov. 14, 1969. Originally set up at the space center's Press Site, the clock was used through the final space shuttle mission, STS-135, launched on July 8, 2011. The old countdown clock was replaced in 2014 with a modern light emitting diode, or LED, display.

  16. Countdown Clock Ribbon Cutting

    NASA Image and Video Library

    2016-03-01

    Confetti is launched as the spaceport's historic countdown clock is dedicated as the newest display at the Kennedy Space Center Visitor Complex. Now located at the entrance to the visitor complex, the spaceport's historic countdown clock was used starting with the launch of Apollo 12 on Nov. 14, 1969. Originally set up at the space center's Press Site, the clock operated through the final space shuttle mission, STS-135, launched on July 8, 2011. The old countdown clock was replaced in 2014 with a modern light emitting diode, or LED, display.

  17. Countdown Clock Ribbon Cutting

    NASA Image and Video Library

    2016-03-01

    Therrin Protze, chief operating officer of the Kennedy Space Center Visitor Complex, left, and center director Bob Cabana watch as confetti was launched as the spaceport's historic countdown clock is dedicated as the newest display at the entrance to Kennedy's visitor complex. The spaceport's historic countdown clock was used beginning with the launch of Apollo 12 on Nov. 14, 1969. Originally set up at the space center's Press Site, the clock was used through the final space shuttle mission, STS-135, launched on July 8, 2011. The old countdown clock was replaced in 2014 with a modern light emitting diode, or LED, display.

  18. In vitro comparison of the cutting efficiency and temperature production of ten different rotary cutting instruments. Part II: electric handpiece and comparison with turbine.

    PubMed

    Ercoli, Carlo; Rotella, Mario; Funkenbusch, Paul D; Russell, Scott; Feng, Changyong

    2009-05-01

    The cutting behavior of dental rotary cutting instruments is influenced by the handpiece used. While the turbine handpiece has been extensively tested in previous studies, limited published information exists on the use of rotary cutting instruments with the electric handpiece system and on possible interactions between rotary cutting instruments and handpiece type. The purpose of this study was to examine the cutting performance of a wide selection of rotary cutting instruments tested with the electric handpiece and compare the results with those of the air-turbine handpiece (Part I), identifying possible interactions between handpiece type and rotary cutting instruments. Ten groups of rotary cutting instruments (n=30) designed for tooth preparation were selected: 9 diamond (7 multi-use, 2 disposable) and 1 carbide. Macor blocks (n=75) were used as a substrate, and 4 cuts were made on each specimen, using a new rotary cutting instrument each time, for a total of 300 cuts. The cuts were performed with an electric handpiece (Intramatic Lux K200), with the same methods used in the Part I study. To qualitatively evaluate the rotary cutting instrument surface characteristics, 1 specimen from each group was examined 3 times with a scanning electron microscope (SEM): before use, then after use, but before being cleaned and sterilized, and finally, after ultrasonic cleaning. To compare rotary cutting instrument performance between the turbine and electric handpieces, the data were analyzed using 2-way ANOVA to study the main effects of the group of rotary cutting instruments, handpieces, and their interaction. For analysis of the significant main effect, 1-way ANOVA and Tukey's Studentized Range test were used (alpha=.05). Compared to the baseline temperature, all rotary cutting instruments showed a reduction of the temperature in the simulated pulp chamber when tested with the electric handpiece. The Great White Ultra (carbide bur) showed the highest rate of advancement

  19. High pressure waterjet cutting industrial needs survey

    NASA Astrophysics Data System (ADS)

    Klavuhn, John; Baker, Bruce

    1989-08-01

    The results are presented of a survey conducted by personnel of the National Center for Excellence in Metalworking Technology (NCEMT) to assess the industrial needs in high pressure water jet cutting (WJC) technology. Survey forms were mailed to approximately 1400 individuals obtained from three mailing lists. The respondents included approximately 200 individuals associated with a variety of industries: 12 percent were WJC equipment suppliers, 40 percent were WJC users, and 48 percent were neither suppliers nor users. The survey addressed five specific areas of WJC technology: research and development, standards, systems, new products, and training and service. Results show that the need having the highest priority is the establishment of a database on WJC that contains the cutting parameters for a wide range of materials. Associated with this objective is the expressed need for an independent demonstration and test center for testing, data generation and operator training. A further need was found for establishing organized efforts in hardware development and research in mechanisms of cutting.

  20. Dealing with Cuts (For Parents)

    MedlinePlus

    ... For Kids For Parents MORE ON THIS TOPIC Cellulitis First Aid: Cuts Staph Infections Bites and Scratches ... Animal Bites Blood Childproofing and Preventing Household Accidents Cellulitis How Stitches Help Kids Heal The Story on ...

  1. Laser cutting of energetic materials

    SciTech Connect

    Rivera, T.; Muenchausen, R.; Sanchez, J.

    1998-12-01

    The authors have demonstrated the feasibility of safely and efficiently cutting and drilling metal cases containing a variety of high explosives (HE) using a Nd:YAG laser. Spectral analysis of the optical emission, occurring during the laser-induced ablation process, is used to identify the removed material. By monitoring changes in the optical emission during the cutting process, the metal-He interface can be observed in real time and the cutting parameters adjusted accordingly. For cutting the HE material itself, the authors have demonstrated that this can be safely and efficiently accomplished by means of a ultraviolet (UV) laser beam obtained from the same Nd:YAG laser using the third or fourth harmonics. They are currently applying this technology to UXO identification and ordnance demilitarization.

  2. Cutting thin sections of bone

    NASA Technical Reports Server (NTRS)

    Ashley, W. W.

    1972-01-01

    Medical equipment for obtaining repetitive planoparallel sections of bone to study healing of bone structure under high gravity stress is described. Device consists of modified saw with diamond cutting edges. Construction of device and manner of use are explained.

  3. Refrigerated cutting tools improve machining of superalloys

    NASA Technical Reports Server (NTRS)

    Dudley, G. M.

    1971-01-01

    Freon-12 applied to tool cutting edge evaporates quickly, leaves no residue, and permits higher cutting rate than with conventional coolants. This technique increases cutting rate on Rene-41 threefold and improves finish of machined surface.

  4. Microwave assisted hard rock cutting

    DOEpatents

    Lindroth, David P.; Morrell, Roger J.; Blair, James R.

    1991-01-01

    An apparatus for the sequential fracturing and cutting of subsurface volume of hard rock (102) in the strata (101) of a mining environment (100) by subjecting the volume of rock to a beam (25) of microwave energy to fracture the subsurface volume of rock by differential expansion; and , then bringing the cutting edge (52) of a piece of conventional mining machinery (50) into contact with the fractured rock (102).

  5. Interactive cutting path analysis programs

    NASA Technical Reports Server (NTRS)

    Weiner, J. M.; Williams, D. S.; Colley, S. R.

    1975-01-01

    The operation of numerically controlled machine tools is interactively simulated. Four programs were developed to graphically display the cutting paths for a Monarch lathe, Cintimatic mill, Strippit sheet metal punch, and the wiring path for a Standard wire wrap machine. These programs are run on a IMLAC PDS-ID graphic display system under the DOS-3 disk operating system. The cutting path analysis programs accept input via both paper tape and disk file.

  6. Underwater welding, cutting and inspection

    SciTech Connect

    Tsai, C.L. . Ohio Underwater Welding Center)

    1995-02-01

    Underwater welding, cutting and inspection of offshore, inland waterway and port facilities are becoming a requirement for both military and industrial communities, as maintenance and repair costs continue to escalate, and as many of the facilities are in operation well beyond their intended design life. In nuclear applications, underwater welding, cutting and inspection for repair and modification of irradiated nuclear power plant components are also a requirement. This article summarizes recent developments in this emerging underwater technology.

  7. Cutting head for ultrasonic lithotripsy

    NASA Technical Reports Server (NTRS)

    Anguluo, E. D.; Goodfriend, R. (Inventor)

    1985-01-01

    A cutting head for attachment to the end of the wire probe of an ultrasonic kidney stone disintegration instrument is described. The cutting head has a plurality of circumferentially arranged teeth formed at one end thereof to provide a cup shaped receptacle for kidney stones encountered during the disintegration procedure. An integral reduced diameter collar diminishes stress points in the wire and reduce breakage thereof.

  8. Effect of Cut Quality on Hybrid Laser Arc Welding of Thick Section Steels

    NASA Astrophysics Data System (ADS)

    Farrokhi, F.; Nielsen, S. E.; Schmidt, R. H.; Pedersen, S. S.; Kristiansen, M.

    From an industrial point of view, in a laser cutting-welding production chain, it is of great importance to know the influence of the attainable laser cut quality on the subsequent hybrid laser arc welding process. Many studies have been carried out in the literature to obtain lower surface roughness values on the laser cut edge. However, in practice, the cost and reliability of the cutting process is crucial and it does not always comply with obtaining the highest surface quality. In this study, a number of experiments on 25 mm steel plates were carried out to evaluate the influence of cut surface quality on the final quality of the subsequent hybrid laser welded joints. The different cut surfaces were obtained by different industrial cutting methods including laser cutting, abrasive water cutting, plasma cutting, and milling. It was found that the mentioned cutting methods could be used as preparation processes for the subsequent hybrid laser arc welding. However, cut quality could determine the choice of process parameters of the following hybrid laser arc welding.

  9. Jasmonates act positively in adventitious root formation in petunia cuttings.

    PubMed

    Lischweski, Sandra; Muchow, Anne; Guthörl, Daniela; Hause, Bettina

    2015-09-22

    Petunia is a model to study the process of adventitious root (AR) formation on leafy cuttings. Excision of cuttings leads to a transient increase in jasmonates, which is regarded as an early, transient and critical event for rooting. Here, the role of jasmonates in AR formation on petunia cuttings has been studied by a reverse genetic approach. To reduce the endogenous levels of jasmonates, transgenic plants were generated expressing a Petunia hybrida ALLENE OXIDE CYCLASE (PhAOC)-RNAi construct. The transgenic plants exhibited strongly reduced PhAOC transcript and protein levels as well as diminished accumulation of cis-12-oxo-phytodienoic acid, jasmonic acid and jasmonoyl-isoleucine after wounding in comparison to wild type and empty vector expressing plants. Reduced levels of endogenous jasmonates resulted in formation of lower numbers of ARs. However, this effect was not accompanied by altered levels of auxin and aminocyclopropane carboxylate (ACC, precursor of ethylene) or by impaired auxin and ethylene-induced gene expression. Neither activity of cell-wall invertases nor accumulation of soluble sugars was altered by jasmonate deficiency. Diminished numbers of AR in JA-deficient cuttings suggest that jasmonates act as positive regulators of AR formation in petunia wild type. However, wound-induced rise in jasmonate levels in petunia wild type cuttings seems not to be causal for increased auxin and ethylene levels and for sink establishment.

  10. Express

    Integrated Risk Information System (IRIS)

    Express ; CASRN 101200 - 48 - 0 Human health assessment information on a chemical substance is included in the IRIS database only after a comprehensive review of toxicity data , as outlined in the IRIS assessment development process . Sections I ( Health Hazard Assessments for Noncarcinogenic Effect

  11. Cut Front Geometry Characterization in Cutting Applications of Brass with Abrasive Water Jet

    NASA Astrophysics Data System (ADS)

    Akkurt, Adnan

    2010-06-01

    Abrasive water jet (AWJ) cutting is an advanced manufacturing process for machining hard to cut materials. In this study, brass-353 samples of different thicknesses were cut by AWJ using different feed rates to identify the relationships between depth of cut (material thickness), feed rate, and deflection of cutting edge geometry. The effects of material thickness on the AWJ cut surface roughness were investigated and discussed. Deflection of cutting edge geometry in AWJ cutting process was assessed. Cutting edge geometry was characterized by analyzing the surface properties of cut samples.

  12. 30 CFR 717.14 - Backfilling and grading of road cuts, mine entry area cuts, and other surface work areas.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ..., ensure stability, and control erosion on final graded slopes, cut-and-fill terraces may be allowed if the... feet unless specifically approved by the regulatory authority as necessary for stability erosion... authority to prevent excessive erosion and to provide long/term stability. (3) The slope of the terrace...

  13. 30 CFR 717.14 - Backfilling and grading of road cuts, mine entry area cuts, and other surface work areas.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ..., ensure stability, and control erosion on final graded slopes, cut-and-fill terraces may be allowed if the... feet unless specifically approved by the regulatory authority as necessary for stability erosion... authority to prevent excessive erosion and to provide long/term stability. (3) The slope of the terrace...

  14. 30 CFR 717.14 - Backfilling and grading of road cuts, mine entry area cuts, and other surface work areas.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ..., ensure stability, and control erosion on final graded slopes, cut-and-fill terraces may be allowed if the... feet unless specifically approved by the regulatory authority as necessary for stability erosion... authority to prevent excessive erosion and to provide long/term stability. (3) The slope of the terrace...

  15. Evalaution and optimization of laser cutting parametersfor plywood materials

    NASA Astrophysics Data System (ADS)

    Eltawahni, H. A.; Rossini, N. S.; Dassisti, M.; Alrashed, K.; Aldaham, T. A.; Benyounis, K. Y.; Olabi, A. G.

    2013-09-01

    Laser process parameters influence greatly the width of kerfs and quality of the cut edges. This article reports experiments on the laser plywood-cutting performance of a CW 1.5 kW CO2 Rofin laser, based on design of experiments (DOE). The laser was used to cut three thicknesses 3, 6 and 9 mm of plywood panels. The process factors investigated are: laser power, cutting speed, air pressure and focal point position. The aim of this work is to relate the cutting edge quality parameters namely: upper kerf (UK), lower kerf (LK), the ratio between upper to lower kerfs and the operating cost to the process parameters mentioned above. Mathematical models were developed to establish the relationship between the process parameters and the edge quality parameters, and special graphs were drawn for this purpose. Finally, a numerical optimization was performed to find out the optimal process setting at which both kerfs would lead to a ratio of about 1, and at which low cutting cost take place.

  16. Side Flow Effect on Surface Generation in Nano Cutting

    NASA Astrophysics Data System (ADS)

    Xu, Feifei; Fang, Fengzhou; Zhang, Xiaodong

    2017-05-01

    The side flow of material in nano cutting is one of the most important factors that deteriorate the machined surface quality. The effects of the crystallographic orientation, feed, and the cutting tool geometry, including tool edge radius, rake angle and inclination angle, on the side flow are investigated employing molecular dynamics simulation. The results show that the stagnation region is formed in front of tool edge and it is characterized by the stagnation radius R s and stagnation height h s . The side flow is formed because the material at or under the stagnation region is extruded by the tool edge to flow to the side of the tool edge. Higher stagnation height would increase the size of the side flow. The anisotropic nature of the material which partly determines the stagnation region also influences the side flow due to the different deformation mechanism under the action of the tool edge. At different cutting directions, the size of the side flow has a great difference which would finally affect the machined surface quality. The cutting directions of {100} < 011>, {110} < 001>, and {110} < 1-10 > are beneficial to obtain a better surface quality with small side flow. Besides that, the side flow could be suppressed by reducing the feed and optimizing the cutting tool geometry. Cutting tool with small edge radius, large positive rake angle, and inclination angle would decrease the side flow and consequently improve the machined surface quality.

  17. Occupational exposure to dioxins by thermal oxygen cutting, welding, and soldering of metals.

    PubMed Central

    Menzel, H M; Bolm-Audorff, U; Turcer, E; Bienfait, H G; Albracht, G; Walter, D; Emmel, C; Knecht, U; Päpke, O

    1998-01-01

    This paper focuses on one aspect of occupational dioxin exposure that is novel and unexpected. Exposures in excess of the German threshold limit value of 50 pg international toxicity equivalent (I-TEQ)/m3 are very frequent, unpredictable, and sometimes very high--up to 6612 pg I-TEQ/m3--during thermal oxygen cutting at scrap metal and demolition sites. The same procedure involving virgin steel in steel trade and mass production of steel objects gave no such evidence, even though no final conclusions can be drawn because of the low number of samples analyzed. Low dioxin exposures during inert gas electric arc welding confirm previous literature findings, whereas soldering and thermal oxygen cutting in the presence of polyvinyl chloride give rise to concern. The consequences of occupational dioxin exposure were studied by analysis of the dioxin-blood concentration, the body burden, of men performing thermal oxygen cutting at scrap metal reclamation and demolition sites, in steel trade and producing plants as well as for industrial welders and white-collar workers. The results concerning body burdens are in excellent agreement with the dioxin exposure as characterized by dioxin air concentration in the workplace. The significant positive correlation between duration and frequency of performing thermal oxygen cutting at metal reclamation and demolition sites expressed in job-years and dioxin body burden speaks for the occupational origin of the observed overload after long times. The results reported here lead to consequences for occupational health, which are discussed and require immediate attention. Images Figure 1 PMID:9599722

  18. Dynamic phenomena and quality defects in laser cutting

    NASA Astrophysics Data System (ADS)

    Schuöcker, Dieter; Schuöcker, Georg

    2012-07-01

    Laser cutting of sheet metals is used all over the world by production companies since it combines high speed, excellent quality and economic advantages. Nevertheless certain limits exist for materials thickness and speed and also to quality of the cut edges that show eventually strong roughness and adherent material as dross and slag. In order to extend these limits and to approve especially cutting speed and quality of the cut edges the mechanism of laser cutting must be fully understood. As far as it concerns steady state cutting the phenomena contributed to the process with a thin liquid layer covering the momentary end of the cut kerf that serves for absorption of laser radiation and also for generation of reaction heat also for melting of the solid material and finally for the ejection of liquid material at the bottom of the work piece due to the friction with the process gas have been clarified a long time before. Also dynamic phenomena associated to reaction and to waves on the surface of the liquid body that all lead to a certain roughness have been described in the past. Nevertheless the phenomena taking place inside the liquid layer are not fully understood especially the influence of surface tension that is much higher than the pressure in the melt and would in principal inhibit any ejection of melt that is necessary for cutting. Therefore the authors carried out an analysis of the processes taking place in the liquid body that leads to a picture with a discontinuous ejection of melt and explains the formation of a rough surface structure and also of adherent material for the case of a rather thick workpiece (> 10mm).

  19. Doubly Rotated Cut SAW Devices.

    DTIC Science & Technology

    1980-06-01

    A D A O S G 7 3 A M T O R A I N C S C O T T S A L E A R I Z G V E R N M E N T E L C T R O N I C S I V F / B 2 0 / 2 DOUBLY ROTATED CUT SAW DEVICES...IEEEEI-/ II//E///III I jjj 5.1 -I I II II II F~ ~ 2, I UUGLASSIF1 U100TVw CLAMOGmeIawor OU I lulP&g EWhm oe ae & oubly Rotated Cut SAW Devices& . r...doubly rotated cuts of quartz possessing speri r Surface Acoustic Wave (SAW) properties for applications involving environmentally hardened devices. The

  20. AK-cut Crystal Resonators

    DTIC Science & Technology

    1982-12-01

    AK- cut C r y s t a l Resonators A l f r e d Kahan and Ferdinand K. Eu le r S o l i d S t a t e Sciences D i v i s i o n Rome A i r b v e l...l e s s s e n s i t i v e t o angu la r mis- o r i e n t a t i o n than comparable AT- o r BT- cuts . We have a r b i t r a r i - l y...designated these c r y s t a l s as t h e AK- cut . We r e p o r t exper- imenta l da ta f o r seven o r i e n t a t i o n s , +-angle v a r i a t i

  1. The Nichols Wing Cutting Equipment

    NASA Technical Reports Server (NTRS)

    Ford, James B

    1923-01-01

    Described here is wing cutting equipment for the economical production of metal wings for wind tunnel models. The machine will make any size of constant-section wing or strut up to one-sixth inch chord by 36-inch span and up to a thickness of one and one-quarter inches. It cuts a smooth, true model that is accurate to within two-thousandths of an inch on any ordinate. The holding jaws are so designed as to leave the model free of chip marks, and the only hand finishing necessary after the cutting is a rub with amunite to remove burrs. The actual change on ordinate in this finishing rub is less than .0002 inches.

  2. Stresses in ultrasonically assisted bone cutting

    NASA Astrophysics Data System (ADS)

    Alam, K.; Mitrofanov, A. V.; Bäker, M.; Silberschmidt, V. V.

    2009-08-01

    Bone cutting is a frequently used procedure in the orthopaedic surgery. Modern cutting techniques, such as ultrasonic assisted drilling, enable surgeons to perform precision operations in facial and spinal surgeries. Advanced understanding of the mechanics of bone cutting assisted by ultrasonic vibration is required to minimise bone fractures and to optimise the technique performance. The paper presents results of finite element simulations on ultrasonic and conventional bone cutting analysing the effects of ultrasonic vibration on cutting forces and stress distribution. The developed model is used to study the effects of cutting and vibration parameters (e.g. amplitude and frequency) on the stress distributions in the cutting region.

  3. Modeling of metal cutting as purposeful fracture of work material

    NASA Astrophysics Data System (ADS)

    Abushawashi, Yalla Mussa

    Metal cutting, or simply machining, is one of the oldest processes for shaping components in the manufacturing industry. It is widely quoted that 15% of the value of all mechanical components manufactured worldwide is derived from machining operations. The most influential model for metal cutting is the single-shear plane model (SSPM) of chip formation. The common notion is that new surfaces are formed simply by `plastic flow around the tool tip' so that metal cutting is one of the deforming processes. A number of cutting theories and the finite element method (FEM) models have been developed based on this concept. Metal cutting simulation models are available in commercial FEM packages. However, these model predictions and numerical simulations do not agree with the trends and phenomena observed in metal cutting experiments. Therefore, it is of the utmost importance to have a physically sound model of metal cutting. This thesis is based on the concept that metal cutting is the purposeful fracture of the work material. To reduce the energy required for fracture, one should minimize the energy of plastic deformation of the work material in its transformation into the chip because this energy constitutes up to 80% of the total energy required by the cutting system. Increased tool life and machining efficiency are the outcomes of such an optimization. To investigate this concept requires a work material model which considers the entire process from plastic deformation, damage initiation to final fracture. In this thesis, a work material model was developed based on the recent advancement in ductile fracture of metals. The model parameters must be determined under conditions that are pertinent to metal cutting. In machining, the work material experiences a complex, evolving multi-axial stress history. The existing testing specimens such as the notched bars and flat grooved specimens do not cover the stress triaxiality range found in machining. To generate material

  4. Microbiopsy/precision cutting devices

    DOEpatents

    Krulevitch, P.A.; Lee, A.P.; Northrup, M.A.; Benett, W.J.

    1999-07-27

    Devices are disclosed for performing tissue biopsy on a small scale (microbiopsy). By reducing the size of the biopsy tool and removing only a small amount of tissue or other material in a minimally invasive manner, the risks, costs, injury and patient discomfort associated with traditional biopsy procedures can be reduced. By using micromachining and precision machining capabilities, it is possible to fabricate small biopsy/cutting devices from silicon. These devices can be used in one of four ways (1) intravascularly, (2) extravascularly, (3) by vessel puncture, and (4) externally. Additionally, the devices may be used in precision surgical cutting. 6 figs.

  5. Female genital cutting: nursing implications.

    PubMed

    Goldenstein, Rachel A

    2014-01-01

    Female genital cutting (FGC) is a practice that affects millions of girls and women worldwide. This deeply rooted practice has cultural, religious, and psychosexual meaning to its practitioners, but it also carries long-term physical and mental complications. Decried as a human rights violation, nonetheless this practice is still carried out today. Nurses are in a unique position to contact and educate women who have been cut or are at risk for mutilation. To advocate for these women, a thorough understanding of the practice of FGC, its cultural overtones, religious implications, and psychosexual effects is needed.

  6. Document segmentation via oblique cuts

    NASA Astrophysics Data System (ADS)

    Svendsen, Jeremy; Branzan-Albu, Alexandra

    2013-01-01

    This paper presents a novel solution for the layout segmentation of graphical elements in Business Intelligence documents. We propose a generalization of the recursive X-Y cut algorithm, which allows for cutting along arbitrary oblique directions. An intermediate processing step consisting of line and solid region removal is also necessary due to presence of decorative elements. The output of the proposed segmentation is a hierarchical structure which allows for the identification of primitives in pie and bar charts. The algorithm was tested on a database composed of charts from business documents. Results are very promising.

  7. Hypervelocity cutting machine and method

    DOEpatents

    Powell, James R.; Reich, Morris

    1996-11-12

    A method and machine 14 are provided for cutting a workpiece 12 such as concrete. A gun barrel 16 is provided for repetitively loading projectiles 22 therein and is supplied with a pressurized propellant from a storage tank 28. A thermal storage tank 32,32A is disposed between the propellant storage tank 28 and the gun barrel 16 for repetitively receiving and heating propellant charges which are released in the gun barrel 16 for repetitively firing projectiles 22 therefrom toward the workpiece 12. In a preferred embodiment, hypervelocity of the projectiles 22 is obtained for cutting the concrete workpiece 12 by fracturing thereof.

  8. Hypervelocity cutting machine and method

    DOEpatents

    Powell, J.R.; Reich, M.

    1996-11-12

    A method and machine are provided for cutting a workpiece such as concrete. A gun barrel is provided for repetitively loading projectiles therein and is supplied with a pressurized propellant from a storage tank. A thermal storage tank is disposed between the propellant storage tank and the gun barrel for repetitively receiving and heating propellant charges which are released in the gun barrel for repetitively firing projectiles therefrom toward the workpiece. In a preferred embodiment, hypervelocity of the projectiles is obtained for cutting the concrete workpiece by fracturing thereof. 10 figs.

  9. Microbiopsy/precision cutting devices

    DOEpatents

    Krulevitch, Peter A.; Lee, Abraham P.; Northrup, M. Allen; Benett, William J.

    1999-01-01

    Devices for performing tissue biopsy on a small scale (microbiopsy). By reducing the size of the biopsy tool and removing only a small amount of tissue or other material in a minimally invasive manner, the risks, costs, injury and patient discomfort associated with traditional biopsy procedures can be reduced. By using micromachining and precision machining capabilities, it is possible to fabricate small biopsy/cutting devices from silicon. These devices can be used in one of four ways 1) intravascularly, 2) extravascularly, 3) by vessel puncture, and 4) externally. Additionally, the devices may be used in precision surgical cutting.

  10. Wedge cutting of mild steel by CO 2 laser and cut-quality assessment in relation to normal cutting

    NASA Astrophysics Data System (ADS)

    Yilbas, B. S.; Karatas, C.; Uslan, I.; Keles, O.; Usta, Y.; Yilbas, Z.; Ahsan, M.

    2008-10-01

    In some applications, laser cutting of wedge surfaces cannot be avoided in sheet metal processing and the quality of the end product defines the applicability of the laser-cutting process in such situations. In the present study, CO 2 laser cutting of the wedge surfaces as well as normal surfaces (normal to laser beam axis) is considered and the end product quality is assessed using the international standards for thermal cutting. The cut surfaces are examined by the optical microscopy and geometric features of the cut edges such as out of flatness and dross height are measured from the micrographs. A neural network is introduced to classify the striation patterns of the cut surfaces. It is found that the dross height and out of flatness are influenced significantly by the laser output power, particularly for wedge-cutting situation. Moreover, the cut quality improves at certain value of the laser power intensity.

  11. Automated internal pipe cutting device

    DOEpatents

    Godlewski, William J.; Haffke, Gary S.; Purvis, Dale; Bashar, Ronald W.; Jones, Stewart D.; Moretti, Jr., Henry; Pimentel, James

    2003-01-21

    The invention is a remotely controlled internal pipe cutting device primarily used for cutting pipes where the outside of the pipe is inaccessible at the line where the cut is to be made. The device includes an axial ram within a rotational cylinder which is enclosed in a housing. The housing is adapted for attachment to an open end of the pipe and for supporting the ram and cylinder in cantilever fashion within the pipe. A radially movable cutter, preferably a plasma arc torch, is attached to the distal end of the ram. A drive mechanism, containing motors and mechanical hardware for operating the ram and cylinder, is attached to the proximal end of the housing. The ram and cylinder provide for moving the cutter axially and circumferentially, and a cable assembly attached to a remote motor provide for the movement of the cutter radially, within the pipe. The control system can be adjusted and operated remotely to control the position and movement of the cutter to obtain the desired cut. The control system can also provide automatic standoff control for a plasma arc torch.

  12. Model aids cuttings transport prediction

    SciTech Connect

    Gavignet, A.A. ); Sobey, I.J. )

    1989-09-01

    Drilling of highly deviated wells can be complicated by the formation of a thick bed of cuttings at low flow rates. The model proposed in this paper shows what mechanisms control the thickness of such a bed, and the model predictions are compared with experimental results.

  13. Brazilian science faces swingeing cuts

    NASA Astrophysics Data System (ADS)

    Ivanissevich, Alicia

    2017-05-01

    A number of “big-science” projects in Brazil could be hit if the government pushes through a 44% cut to the R5bn (£1.28bn) budget of the Ministry of Science, Technology, Innovations and Communications (MCTIC).

  14. Turtle Functions Downstream of Cut in Differentially Regulating Class Specific Dendrite Morphogenesis in Drosophila

    PubMed Central

    Sulkowski, Mikolaj J.; Iyer, Srividya Chandramouli; Kurosawa, Mathieu S.; Iyer, Eswar Prasad R.; Cox, Daniel N.

    2011-01-01

    Background Dendritic morphology largely determines patterns of synaptic connectivity and electrochemical properties of a neuron. Neurons display a myriad diversity of dendritic geometries which serve as a basis for functional classification. Several types of molecules have recently been identified which regulate dendrite morphology by acting at the levels of transcriptional regulation, direct interactions with the cytoskeleton and organelles, and cell surface interactions. Although there has been substantial progress in understanding the molecular mechanisms of dendrite morphogenesis, the specification of class-specific dendritic arbors remains largely unexplained. Furthermore, the presence of numerous regulators suggests that they must work in concert. However, presently, few genetic pathways regulating dendrite development have been defined. Methodology/Principal Findings The Drosophila gene turtle belongs to an evolutionarily conserved class of immunoglobulin superfamily members found in the nervous systems of diverse organisms. We demonstrate that Turtle is differentially expressed in Drosophila da neurons. Moreover, MARCM analyses reveal Turtle acts cell autonomously to exert class specific effects on dendritic growth and/or branching in da neuron subclasses. Using transgenic overexpression of different Turtle isoforms, we find context-dependent, isoform-specific effects on mediating dendritic branching in class II, III and IV da neurons. Finally, we demonstrate via chromatin immunoprecipitation, qPCR, and immunohistochemistry analyses that Turtle expression is positively regulated by the Cut homeodomain transcription factor and via genetic interaction studies that Turtle is downstream effector of Cut-mediated regulation of da neuron dendrite morphology. Conclusions/Significance Our findings reveal that Turtle proteins differentially regulate the acquisition of class-specific dendrite morphologies. In addition, we have established a transcriptional regulatory

  15. High cut-off dialysis in chronic haemodialysis patients.

    PubMed

    Girndt, Matthias; Fiedler, Roman; Martus, Peter; Pawlak, Michael; Storr, Markus; Bohler, Torsten; Glomb, Marcus A; Liehr, Kristin; Henning, Christian; Templin, Markus; Trojanowicz, Bogusz; Ulrich, Christof; Werner, Kristin; Zickler, Daniel; Schindler, Ralf

    2015-12-01

    Haemodialysis patients suffer from chronic systemic inflammation and high incidence of cardiovascular disease. One cause for this may be the failure of diseased kidneys to eliminate immune mediators. Current haemodialysis treatment achieves insufficient elimination of proteins in the molecular weight range 15-45 kD. Thus, high cut-off dialysis might improve the inflammatory state. In this randomized crossover trial, 43 haemodialysis patients were treated for 3 weeks with high cut-off or high-flux dialysis. Inflammatory plasma mediators, monocyte subpopulation distribution and leucocyte gene expression were quantified. High cut-off dialysis supplemented by a low-flux filter did not influence the primary end-point, expression density of CD162 on monocytes. Nevertheless, treatment reduced multiple immune mediators in plasma. Such reduction proved - at least for some markers - to be a sustained effect over the interdialytic interval. Thus, for example, soluble TNF-receptor 1 concentration predialysis was reduced from median 13·3 (IQR 8·9-17·2) to 9·7 (IQR 7·5-13·2) ng/mL with high cut-off while remaining constant with high-flux treatment. The expression profile of multiple proinflammatory genes in leucocytes was significantly dampened. Treatment was well tolerated although albumin losses in high cut-off dialysis would be prohibitive against long-term use. The study shows for the first time that a dampening effect of high cut-off dialysis on systemic inflammation is achievable. Earlier studies had failed due to short study duration or insufficient dialysis efficacy. Removal of soluble mediators from the circulation influences cellular activation levels in leucocytes. Continued development of less albumin leaky membranes with similar cytokine elimination is justified. © 2015 Stichting European Society for Clinical Investigation Journal Foundation.

  16. Cross Cutting Structural Design for Exploration Systems

    NASA Technical Reports Server (NTRS)

    Semmes, Edmund B.

    2007-01-01

    The challenge of our new National Space Policy and NASA's Vision for Space Exploration (VSE) is keyed to the development of more effective space access and transportation systems. Optimizing in-space systems through innovative cross cutting structural designs that reduce mass, combine functional requirements and improve performance can significantly advance spacecraft designs to meet the ever growing demands of our new National Space Policy. Dependence on limited structural designs is no longer an option. We must create robust materials, forms, function and evolvable systems. We must advance national policy objectives in the design, development, test and operation of multi-billion dollar new generation crew capsules by enabling them to evolve in meeting the requirements of long duration missions to the moon and mars. This paper discusses several current issues and major design drivers for consideration in structural design of advanced spacecraft systems. Approaches to addressing these multifunctional requirements is presented as well as a discussion on utilizing Functional Analysis System Technique (FAST) in developing cross cutting structural designs for future spacecraft. It will be shown how easy it is to deploy such techniques in any conceptual architecture definition or ongoing preliminary design. As experts in merging mission, safety and life support requirements of the frail human existence into robust vehicle and habitat design, we will conquer the final frontier, harness new resources and develop life giving technologies for mankind through more innovative designs. The rocket equation tells us that a reduction in mass optimizes our propulsive results. Primary and secondary structural elements provide for the containment of gases, fluids and solids; translate and sustain loads/impacts; conduct/radiate thermal energy; shield from the harmful effects of radiation; provide for grounding/bonding of electrical power systems; compartmentalize operational

  17. CO2-Laser Cutting Fiber Reinforced Polymers

    NASA Astrophysics Data System (ADS)

    Mueller, R.; Nuss, Rudolf; Geiger, Manfred

    1989-10-01

    Guided by experimental investigations laser cutting of glass fiber reinforced reactive injection moulded (RRIM)-polyurethanes which are used e.g. in car industry for bumpers, spoilers, and further components is described. A Comparison with other cutting techniques as there are water jet cutting, milling, punching, sawing, cutting with conventional knife and with ultrasonic excited knife is given. Parameters which mainly influence cutting results e.g. laser power, cutting speed, gas nature and pressure will be discussed. The problematic nature in characterising micro and macro geometry of laser cut edges of fiber reinforced plastic (FRP) is explained. The topography of cut edges is described and several characteristic values are introduced to specify the obtained working quality. The surface roughness of laser cut edges is measured by both, an optical and a mechanical sensor and their reliabilities are compared.

  18. X-Z-Theta cutting method

    DOEpatents

    Bieg, L.F.

    1993-01-12

    A method for machining a workpiece. The method includes the use of a rotary cutting tool mounted on the end of a movable arm. The arm is adapted to move in a plane perpendicular to the axis of rotation of the cutting tool. The cutting tool has cutting teeth to cut chips of material off of the workpiece in a predetermined size and shape to facilitate better removal of the chips from the workpiece. The teeth can be of different type and length to permit the tool to both rough cut and finish cut the workpiece during machining. The total depth of cut is divided by the number of tool teeth, so that the longest tool always performs the finishing cut.

  19. Knife and impact cutting of lamb bone.

    PubMed

    King, M J

    1999-05-01

    The forces and hence fracture energies required to cut bone are presented in this paper and the merits of cutting with a high speed blade are considered. A plain knife blade was used to cut cancellous and compact lamb bone using three different methods. A microtome was used to produce a range of cut thicknesses which enabled the fracture energy to be separated into friction, surface fracture and plastic deformation energies. A tensile test machine was used to produce thicker off-cuts so that the energy required to cut through full sections of bone could be determined. A high speed rail gun was used to cut at speeds up to 130 m/s. The energy required to cut bone did not change with blade speed. However, the energies measured during the cutting varied over a wide range. In situations in which the surface of the cut bone exhibited a very uneven surface high energy was required, whereas when the resulting cut surface was planar the cutting energy was low. A light weight blade which impacts the bone at high speed will transmit a small impulse to the carcass which may be absorbed without transmitting strain to the muscle/connective tissue. This may allow the development of a high speed knife which will cut bone without excessively damaging the meat surrounding the cut.

  20. Evaluation of the hemostatic and coagulation effects of AUTO CUT and DRY CUT using a computer-controlled cutting system.

    PubMed

    Szyrach, Mara N I; Tolba, Rene H; Voigtländer, Matthias; Neugebauer, Alexander; Enderle, Markus D

    2010-05-01

    To evaluate a newly developed computer-controlled cutting system for the generation of standardized resections and to systematically compare the hemostatic properties and tissue effect of 2 cutting modes, namely, AUTO CUT and DRY CUT used in urologic procedures. An isolated perfused kidney model was used to assess blood loss and coagulation depth after resection of tissue specimens of standardized geometry, size, and cutting velocity with a resection loop. Three different effect settings (E1, E3, and E6; 200 W) of the electrosurgical modes AUTO CUT and DRY CUT were compared. Blood loss was determined semiquantitatively by weighing a swab before and after placing it onto the resection area. The coagulation depth was estimated microscopically on cross sections. The computer-controlled cutting system creates resections of standardized geometry and size with a high reproducibility. An effect level-dependent increase in hemostasis and coagulation depth could be demonstrated with the cutting modes DRY CUT and AUTO CUT using this computer-controlled cutting system. The hemostatic effect with DRY CUT is significantly more pronounced than with AUTO CUT (E1, E3: P < .0001, E6: P = .004), and the coagulation is significantly deeper (E1, E3, E6: P < .0001). The computer-controlled cutting system creating reproducible resections in combination with the isolated perfused kidney model offers the possibility to systematically investigate bleeding rate and coagulation depth. The stronger hemostatic properties of the DRY CUT mode are more favorable for urologic interventions requiring a higher hemostatic effect than the AUTO CUT mode. Copyright 2010 Elsevier Inc. All rights reserved.

  1. Note on recursion relations for the Q -cut representation

    NASA Astrophysics Data System (ADS)

    Feng, Bo; He, Song; Huang, Rijun; Luo, Ming-xing

    2017-01-01

    In this note, we study the Q -cut representation by combining it with BCFW deformation. As a consequence, the one-loop integrand is expressed in terms of a recursion relation, i.e., n-point one-loop integrand is constructed using tree-level amplitudes and m-point one-loop integrands with m ≤ n - 1. By giving explicit examples, we show that the integrand from the recursion relation is equivalent to that from Feynman diagrams or the original Q -cut construction, up to scale free terms.

  2. Gravitropism in cut flower stalks of snapdragon.

    PubMed

    Philosoph-Hadas, S; Friedman, H; Meir, S; Berkovitz-SimanTov, R; Rosenberger, I; Halevy, A H; Kaufman, P B; Balk, P; Woltering, E J

    2001-01-01

    The negative gravitropic response of cut flower stalks is a complex multistep process that requires the participation of various cellular components acting in succession or in parallel. The process was particularly characterized in snapdragon (Antirrhinum majus L.) spikes with regard to (1) gravity stimulus perception associated with amyloplast reorientation; (2) stimulus transduction mediated through differential changes in the level, action and related genes of auxin and ethylene and their possible interaction; (3) stimulus response associated with differential growth leading to stalk curvature; (4) involvement of cytosolic calcium and actin cytoskeleton. Results show that the gravity-induced amyloplast reorientation, differential over-expression of two early auxin responsive genes and asymmetrical distribution of free IAA are early events in the bending process. These precede the asymmetrical ethylene production and differential stem growth, which was derived from initial shrinkage of the upper stem side and a subsequent elongation of the lower stem side. Results obtained with various calcium- and cytoskeleton-related agents indicate that cytosolic calcium and actin filaments may play essential roles in gravitropism-related processes of cut flower stalks. Therefore, modulators of these two physiological mediators may serve as means for controlling any undesired gravitropic bending.

  3. Measurement of Cut Front Properties in Laser Cutting

    NASA Astrophysics Data System (ADS)

    Thombansen, Ulrich; Hermanns, Torsten; Molitor, Thomas; Pereira, Milton; Schulz, Wolfgang

    Cut-front properties are a key variable in laser-cutting and thus of major importance for self-optimization. Within the Cluster of Excellence at RWTH Aachen University, several achievements were made in setting up sensor-systems that provide information on the operating-point of this melt-based manufacturing process. These achievements contribute to a gradual increase in system-transparency which is seen as an enabler for self-optimization. Instead of searching for a single measurand to characterize the course of the process, an approach is being presented which establishesa surrogate criterion to allow determination of the current operating-point. In the depicted area, this is done by joining sources of information from process observation, determining boundary-conditions such as actual feed-rate and modeling of process-variables. Although process-variables like properties of the cutting-front are influenced through more than one process parameter, a concept for a sensor-system is reported showing the correlation between properties of the melt-front and the current feed-rate. The results are compared to a solution derived from process-simulation.

  4. Laser Cutting of Thin Nickel Bellows

    NASA Technical Reports Server (NTRS)

    Butler, C. L.

    1986-01-01

    Laser cutting technique produces narrow, precise, fast, and repeatable cuts in thin nickel-allow bellows material. Laser cutting operation uses intense focused beam to melt material and assisting gas to force melted material through part thickness, creating void. When part rotated or moved longitudinally, melting and material removal continuous and creates narrow, fast, precise, and repeatable cut. Technique used to produce cuts of specified depths less than material thickness. Avoids distortion, dents, and nicks produced in delicate materials during lathe trimming operations, which require high cutting-tool pressure and holding-fixture forces.

  5. CO2 laser cutting of natural granite

    NASA Astrophysics Data System (ADS)

    Riveiro, A.; Mejías, A.; Soto, R.; Quintero, F.; del Val, J.; Boutinguiza, M.; Lusquiños, F.; Pardo, J.; Pou, J.

    2016-01-01

    Commercial black granite boards (trade name: "Zimbabwe black granite") 10 mm thick, were successfully cut by a 3.5 kW CO2 laser source. Cutting quality, in terms of kerf width and roughness of the cut wall, was assessed by means of statistically planned experiments. No chemical modification of the material in the cutting walls was detected by the laser beam action. Costs associated to the process were calculated, and the main factors affecting them were identified. Results reported here demonstrate that cutting granite boards could be a new application of CO2 laser cutting machines provided a supersonic nozzle is used.

  6. Cutting

    MedlinePlus

    ... dealing with feelings that seem too difficult to bear or bad situations they think can't change. ... rejection and helplessness she felt she couldn't bear. "I never looked at it as anything that ...

  7. Cutting

    MedlinePlus

    ... Parents for Kids for Teens Search Teens Home Body Mind Sexual Health Food & Fitness Diseases & Conditions Infections Q& ... to do. But you can't get your mind off feeling upset, and your body has this knot of emotional pain. Before you ...

  8. AK-cut crystal resonators

    NASA Technical Reports Server (NTRS)

    Kahan, A.; Euler, F. K.

    1983-01-01

    Calculations have predicted the existence of crystallographically doubly rotated quartz orientations with turnover temperatures which are considerably less sensitive to angular misorientation then comparable AT- or BT-cuts. These crystals are arbitrarily designated as the AK-cut. Experimental data is given for seven orientations, phi-angle variations between 30-46 deg and theta-angle variations between 21-28 deg measured on 3.3-3.4 MHz fundamental mode resonators vibrating in the thickness shear c-mode. The experimental turnover temperatures of these resonators are between 80 C and 150 C, in general agreement with calculated values. The normalized frequency change as a function of temperature has been fitted with a cubic equation.

  9. NASA budget, EOS face cuts

    NASA Astrophysics Data System (ADS)

    Simarski, Lynn Teo

    The hefty FY 1992 increase for the National Aeronautics and Space Administration proposed by President George Bush has begun to attract Congressional budget-cutting axes, as predicted. The first cuts, however, have come from an unexpected ax-wielder—the space subcommittee of the House Committee on Space, Science, and Technology—normally a cheerleader for NASA in recent years.The subcommittee trimmed $488 million from NASA's budget request of $15.8 billion on April 11, according to a staff member of the space subcommittee. Notably, the panel did not touch the allotment for Space Station Freedom. The subcommittee has submitted the NASA authorization bill to the full committee, which is slated to act on it by the end of April, according to the Congressional Quarterly Weekly Report.

  10. Reservoir management cost-cutting

    SciTech Connect

    Gulati, M.S.

    1996-12-31

    This article by Mohinder S. Gulati, Chief Engineer, Unocal Geothermal Operations, discusses cost cutting in geothermal reservoir management. The reservoir engineer or geoscientist can make a big difference in the economical outcome of a project by improving well performance and thus making geothermal energy more competitive in the energy marketplace. Bringing plants online in less time and proving resources to reduce the cycle time are some of the ways to reduce reservoir management costs discussed in this article.

  11. Expedition 33 Crew Hair Cut

    NASA Image and Video Library

    2012-10-21

    Expedition 33 Flight Engineer Evgeny Tarelkin gets his hair cut at the Cosmonaut Hotel, on Sunday, October 21, 2012, at the Baikonur Cosmodrome in Kazakhstan. Launch of the Soyuz rocket is scheduled for October 23 and will send Expedition 33/34 Flight Engineer Kevin Ford of NASA, Soyuz Commander Oleg Novitskiy and Flight Engineer Engineer Evgeny Tarelkin of ROSCOSMOS on a five-month mission aboard the International Space Station. Photo Credit: (NASA/Bill Ingalls)

  12. Expedition 33 Crew Hair Cut

    NASA Image and Video Library

    2012-10-21

    Expedition 33 Soyuz Commander Oleg Novitskiy gets his hair cut at the Cosmonaut Hotel, on Sunday, October 21, 2012, at the Baikonur Cosmodrome in Kazakhstan. Launch of the Soyuz rocket is scheduled for October 23 and will send Expedition 33/34 Flight Engineer Kevin Ford of NASA, Soyuz Commander Oleg Novitskiy and Flight Engineer Evgeny Tarelkin of ROSCOSMOS on a five-month mission aboard the International Space Station. Photo Credit: (NASA/Bill Ingalls)

  13. Expedition 33 Crew Hair Cut

    NASA Image and Video Library

    2012-10-21

    Expedition 33 Flight Engineer Kevin Ford gets his hair cut at the Cosmonaut Hotel, on Sunday, October 21, 2012, at the Baikonur Cosmodrome in Kazakhstan. Launch of the Soyuz rocket is scheduled for October 23 and will send Expedition 33/34 Flight Engineer Kevin Ford of NASA, Soyuz Commander Oleg Novitskiy and Flight Engineer Evgeny Tarelkin of ROSCOSMOS on a five-month mission aboard the International Space Station. Photo Credit: (NASA/Bill Ingalls)

  14. Drill cuttings mount formation study

    NASA Astrophysics Data System (ADS)

    Teh, Su Yean; Koh, Hock Lye

    2014-07-01

    Oil, Gas and Energy sector has been identified as an essential driving force in the Malaysian Economic Transformation Programs (ETP). Recently confirmed discovery of many offshore oil and gas deposits in Malaysian waters has ignited new confidence in this sector. However, this has also spurred intense interest on safeguarding the health and environment of coastal waters in Malaysia from adverse impact resulting from offshore oil and gas production operation. Offshore discharge of spent drilling mud and rock cuttings is the least expensive and simplest option to dispose of large volumes of drilling wastes. But this onsite offshore disposal may have adverse environmental impacts on the water column and the seabed. It may also pose occupational health hazards to the workers living in the offshore platforms. It is therefore important to model the transport and deposition of drilling mud and rock cuttings in the sea to enable proper assessment of their adverse impacts on the environment and the workers. Further, accumulation of drill particles on the seabed may impede proper operation of pipelines on the seabed. In this paper, we present an in-house application model TUNA-PT developed to cater to local oil and gas industry needs to simulate the dispersion and mount formation of drill cuttings by offshore oil and gas exploration and production platforms. Using available data on Malaysian coastal waters, simulation analyses project a pile formation on the seabed with a maximum height of about 1 m and pile radius of around 30 to 50 m. Simulated pile heights are not sensitive to the heights of release of the cuttings as the sensitivity has been mitigated by the depth of water.

  15. Quantitative laser cutting of plants

    NASA Astrophysics Data System (ADS)

    Schou, Juergen; Heisel, Torben; Nordskov, Arne; Christensen, Svend; Jensen, Peter S.; Thestrup, Birgitte; Toftmann, Bo

    2002-09-01

    It is possible to quantify cutting of plant stems by a laser beam in contrast to mechanical cutting. The biomass of the plants after a certain period under standard green house conditions was used to measure the effect of partial or complete cutting with a laser. Continuous laser irradiation at 10.6 micrometers of the plant stem turned out to be very efficient at values of the energy per width unit above 6 J/mm. The effect of laser irradiation at 355 nm or 1064 nm is less pronounced, but also at these wavelengths the re- growth or continuous growth are reduced. A monocotyledon- type, winter what (Triticum vulgare L), is substantially more resistant than a dicotyledon-type, charlock (Chenopodium album L.) against radiation. The exposure limits for laser light in living plants have been explored as well. The limit in terms of re-growth of the irradiated plants exceeds the MPE (maximum permissible exposure) of human skin by several orders of magnitude. The consequence is that very powerful (unfocused) lasers can be used in any environment without significant impact on living plants.

  16. Aqueous cutting fluid for machining fissionable materials

    DOEpatents

    Duerksen, Walter K.; Googin, John M.; Napier, Jr., Bradley

    1984-01-01

    The present invention is directed to a cutting fluid for machining fissionable material. The cutting fluid is formed of glycol, water and boron compound in an adequate concentration for effective neutron attenuation so as to inhibit criticality incidents during machining.

  17. Cutting Frozen Ground with Disc Saws

    DTIC Science & Technology

    1975-06-01

    a (actor ot 5. taking a depth widtli ratio toi the uncut nbs ol 2. Axle torces on the cutter wheel depend on the design ol the cutting teeth and on...position. If the shoulder of the cutting tool behind the cutting edge is exactly tangential, it will grind against uncut material and...AD-A012 114 CUTTING FROZEN GROUND UITH DISC SAWS Mai colm Mel lor Cold Regions Research and Engineering Laboratory Hanover, New

  18. High Pressure Waterjet Cutting Industrial Needs Survey

    DTIC Science & Technology

    1989-08-25

    Report No. LO High Pressure Waterjet Cutting Industrial Needs Survey N Contract Number N00140-88-C-RC21 I John Klavuhn and Bruce Baker Metalworking...NO. NO ACCESSION NO. Washington, DC 20360-5100 1I TITLE (Include Security Classification) High Pressure Waterjet Cutting Industrial Needs Survey 12...block number) FIELD GROUP SUB-GROUP FIELD__ GROUP____UB-GROUP Waterjet cutting , abrasive waterjet cutting ’. ABSTRACT (Continue on reverse if

  19. Performance of Uncoated Carbide Cutting Tool when Machining Cast Iron in Dry Cutting Condition

    NASA Astrophysics Data System (ADS)

    Jaharah, A. G.; Che Hassan, C. H.; Ghazali, M. J.; Sulong, A. B.; Omar, M. Z.; Nuawi, M. Z.; Ismail, A. R.

    This paper presents the performance of uncoated carbide cutting tool when machining cast iron in dry cutting conditions. Experiments were conducted at various cutting speeds, feed rates, and depths of cut according to Taguchi method design of experiment using a standard orthogonal array L9(34). The effects of cutting speeds (100-146 m/min), feed rates (0.20-0.35 mm/tooth) and depths of cut (1.0-2.0 mm) on the tool life, surface roughness and cutting forces were evaluated using ANOVA. Results showed that the effects of cutting speed, depth of cut and the feed rate were similar affecting the failure of the carbide cutting tools within the range of tested machining parameters. The contribution of cutting speed, feed rate, and depth of cut in controlling the tool life were 32.12%, 38.56% and 29.32% respectively. Whereas, the cutting speed was the main factor influencing the average surface roughness (Ra) value followed by feed rate. These factors contribute 60.53% and 35.59% respectively to the Ra value. On the other hand, cutting forces generated were greatly influenced by the depth of cut (66.52%) and the feed rate (32.6%). Cutting speed was found insignificant in controlling the generated cutting forces.

  20. Hardwood Regeneration After Seed Tree Cutting

    Treesearch

    Robert L. Johnson; R. M. Krinard

    1976-01-01

    Seed trees left at two sites did not appear to influence the establishment or development of reproduction . Seed trees were mainly sweetgum and red oaks. Most reproduction was from sprouting of the stumps and roots of cut trees or from advanced seedlings present in the understory at the time of cutting. Eighteen years after cutting, dominant trees of the reproduction...

  1. Teaching Budget Cuts to Third Graders

    ERIC Educational Resources Information Center

    Weiss, Dale

    2011-01-01

    As a teacher in the Milwaukee Public Schools (MPS) for the past 16 years, this author has grown used to dismal budget cut news arriving each February. Although cuts are always frustrating and their results burdensome, his school has been able to "hang on" reasonably well. This year, however, the budget cuts were extreme. The school's…

  2. Sensitivity of allowable cuts to intensive management.

    Treesearch

    Roger D. Fight; Dennis L. Schweitzer

    1974-01-01

    A sensitivity analysis of allowable cuts on two BLM master units shows that even-flow allowable cuts depend primarily on: (1) assumed long-term growth potential, (2) period that growth increases must be cumulated before they can be removed from the stands on which they occur, and (3) amount and age-class distribution of the initial inventory. Current allowable cut...

  3. Teaching Budget Cuts to Third Graders

    ERIC Educational Resources Information Center

    Weiss, Dale

    2011-01-01

    As a teacher in the Milwaukee Public Schools (MPS) for the past 16 years, this author has grown used to dismal budget cut news arriving each February. Although cuts are always frustrating and their results burdensome, his school has been able to "hang on" reasonably well. This year, however, the budget cuts were extreme. The school's…

  4. 27 CFR 6.92 - Newspaper cuts.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 1 2012-04-01 2012-04-01 false Newspaper cuts. 6.92 Section 6.92 Alcohol, Tobacco Products and Firearms ALCOHOL AND TOBACCO TAX AND TRADE BUREAU, DEPARTMENT OF THE TREASURY LIQUORS âTIED-HOUSEâ Exceptions § 6.92 Newspaper cuts. Newspaper cuts, mats, or...

  5. 27 CFR 6.92 - Newspaper cuts.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 1 2011-04-01 2011-04-01 false Newspaper cuts. 6.92 Section 6.92 Alcohol, Tobacco Products and Firearms ALCOHOL AND TOBACCO TAX AND TRADE BUREAU, DEPARTMENT OF THE TREASURY LIQUORS âTIED-HOUSEâ Exceptions § 6.92 Newspaper cuts. Newspaper cuts, mats, or...

  6. SET OF CUT SETS AND OPTIMUM FLOW,

    DTIC Science & Technology

    maintain the same terminal flow. The method presented stems from the work of Ford and Fulkerson which relates maximum terminal flow to the cut set...separating the terminals. A new set of cut sets called a ’set of M- cut sets’ is introduced from which it is possible to improve edge flows while maintaining maximum terminal flow.

  7. 27 CFR 6.92 - Newspaper cuts.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 1 2014-04-01 2014-04-01 false Newspaper cuts. 6.92 Section 6.92 Alcohol, Tobacco Products and Firearms ALCOHOL AND TOBACCO TAX AND TRADE BUREAU, DEPARTMENT OF THE TREASURY ALCOHOL âTIED-HOUSEâ Exceptions § 6.92 Newspaper cuts. Newspaper cuts, mats, or...

  8. 27 CFR 6.92 - Newspaper cuts.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 1 2013-04-01 2013-04-01 false Newspaper cuts. 6.92 Section 6.92 Alcohol, Tobacco Products and Firearms ALCOHOL AND TOBACCO TAX AND TRADE BUREAU, DEPARTMENT OF THE TREASURY ALCOHOL âTIED-HOUSEâ Exceptions § 6.92 Newspaper cuts. Newspaper cuts, mats, or...

  9. Raise cutting diameters for increased returns

    Treesearch

    H. Clay Smith; G. R., Jr. Trimble; Paul S. DeBald

    1979-01-01

    Diameter-limit cutting is widely used to harvest logs in eastern hardwoods. Studies show that cutting limits are often set so low that they sacrifice financial returns. The value of lumber cut from logs is largely dependent on the diameter, grade, and tree species. As tree size increases so does the proportion of higher grade lumber, and this is reflected in improved...

  10. 27 CFR 6.92 - Newspaper cuts.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false Newspaper cuts. 6.92 Section 6.92 Alcohol, Tobacco Products and Firearms ALCOHOL AND TOBACCO TAX AND TRADE BUREAU, DEPARTMENT OF THE TREASURY LIQUORS âTIED-HOUSEâ Exceptions § 6.92 Newspaper cuts. Newspaper cuts, mats, or...

  11. Sequential versus automated cutting guides in computer-assisted total knee arthroplasty.

    PubMed

    Koulalis, Dimitrios; O'Loughlin, Padhraig F; Plaskos, Christopher; Kendoff, Daniel; Cross, Michael B; Pearle, Andrew D

    2011-12-01

    The accuracy and efficiency of automated cutting guides in CAS systems have not been previously compared with conventional CAS techniques. Therefore, it is not yet clear if these more advanced technologies are warranted. We hypothesized that a novel automated cutting guide with CAS for total knee arthroplasty would be more efficient and more accurate than conventional navigation with sequential cutting blocks. Twelve cadaver legs were used in total. Each leg was randomly assigned to either an automated guide positioning or a conventional freehand computer-navigated guide positioning. The guide positions postosseous fixation and the final bone-cut surfaces were digitized and compared to the targeted cutting planes. The final location of the impacted trial implant was also digitized and compared to the planned implant location. The time for each step and the total time taken to prepare the femur were measured for both groups. The mean femoral preparation time was shorter with the automated cutting guide than the conventional method (5.5 min versus 13.8 min, p<0.001). The average deviation in the final bone resections from the planned resections was significantly lower for the automated cutting guide in the frontal/rotational plane (0.55° versus 1.1°), sagittal plane (0.75° versus 2.0°), and cut height direction (0.56 mm versus 1.6 mm). Therefore, based on these results, we concluded that automated cutting-guide positioning resulted in more efficient and more accurate femoral cuts in comparison to the conventional navigation method in a cadaveric model.

  12. Automated Laser Cutting In Three Dimensions

    NASA Technical Reports Server (NTRS)

    Bird, Lisa T.; Yvanovich, Mark A.; Angell, Terry R.; Bishop, Patricia J.; Dai, Weimin; Dobbs, Robert D.; He, Mingli; Minardi, Antonio; Shelton, Bret A.

    1995-01-01

    Computer-controlled machine-tool system uses laser beam assisted by directed flow of air to cut refractory materials into complex three-dimensional shapes. Velocity, position, and angle of cut varied. In original application, materials in question were thermally insulating thick blankets and tiles used on space shuttle. System shapes tile to concave or convex contours and cuts beveled edges on blanket, without cutting through outer layer of quartz fabric part of blanket. For safety, system entirely enclosed to prevent escape of laser energy. No dust generated during cutting operation - all material vaporized; larger solid chips dislodged from workpiece easily removed later.

  13. Cutting of bent vortex lines

    SciTech Connect

    Wagenleithner, P.

    1982-07-01

    One of the major problems in the application of type II superconductors is the appearance of resistivity in case where a current-carrying specimen is in a longitudinal magnetic field. This is explained by the onset of flux-line cutting events, followed by cross-joining of the line parts. The calculation given here shows the amount of repulsive force and energy between two curved vortex lines and examines the general stability of the vortex-vortex system. First, the actual interaction potential between curved vortices is computed. It includes all electromagnetic and core overlap terms of interactions and self-interaction, and allows computation of the system energy under all curved vortex-line configurations. A computer program is used to find the form of lowest free energy. To do this, special trial functions are established to describe the three-dimensional form of the vortex-vortex system. In these functions parameters determine the qualitative and quantitative form. The asymptotic boundary conditions are built into the nature of the trial functions. The computer program now minimizes the free energy with respect to these parameters. The resulting repulsive energy and force are more than ten times less than the known results for straight flux lines, especially for small asymptotic cutting angles. There is no sharp maximum in the plot of repulsive force versus flux-line separation. A remarkable results is the loss of general stability below a separation distance of several London penetration depths, depending on the cutting angle and the Ginzburg-Landau parameter. The explanation lies in the local attraction of central sections of the vortices as a result of configurational adaption. This explains the onset of resistance at small currents and small magnetic fields.

  14. Cutting costs without drawing blood.

    PubMed

    Copeland, T

    2000-01-01

    When looking for ways to cut costs, most managers reach for the head-count hatchet, and the markets usually roar with approval. But a company can almost always create far more sustainable value by rigorously evaluating the small-ticket capital items that often get rubber-stamped. Drawing on his experience as a consultant and providing numerous anecdotes, the author contends that those "little" requests often prove to be gold plated or unnecessary. A disciplined evaluation involves asking only eight questions and conducting postmortems--regular audits of units' capital spending. But the payoff is enormous. Because cutting the capital budget increases cash flow, the author argues that a permanent cut of just 15% in the planned level of capital spending could boost some companies' market capitalization by as much as 30%. The first three questions--Is this your investment to make? Does it really have to be new? How are our competitors meeting compliance needs?--are asked of operating managers as they assemble capital project requests. The next three are asked by senior managers of themselves and their colleagues as they examine proposals: Is the left hand duplicating investments made by the right? Are trade-offs between profit and capital spending well understood? Are there signs of budget massage? At the end of the review process, senior managers ask: Are we fully using shared assets? How fine-grained are our capacity measures? The author's suggestions for the postmortem include searching for systematic problems with whole classes of expenditures and making sure audit teams come up with specific recommendations for change.

  15. Production and characterization of cut resistant acrylic/copolyaramid fibers via bicomponent wet spinning

    NASA Astrophysics Data System (ADS)

    Hipp, Stephen James

    A composite fiber system consisting of a sheath core bicomponent polymer fiber loaded with hard ceramic particles was developed and characterized for use in cut protective clothing. The core component was comprised of a copolyaramid in order to provide high base cut resistance. An acrylic-copolyaramid polymer blend was used for the sheath component to improve processability and provide potential benefits such as dyeability. Lastly, aluminum oxide particles were incorporated into the fiber core to deflect and deform the cutting edge, further improving cut resistance. A series of designed experiments was used to explore the effects of the wet spinning and heat treatment processes on the structure and properties of the bicomponent fiber. Cut strength of the as-spun fibers was highest when the coagulation rate was slow, promoting the formation of a dense, macrovoid free fiber structure. Upon drawing, fibrillar domains developed within the fiber, further improving cut performance. Cut strength was greatly improved by the heat treatment process despite the fibers becoming highly anisotropic. Addition of the hard particle fillers to the bicomponent fibers showed a decrease in cut strength at the fiber level but nearly doubled the cut strength of resulting fabrics. Finally, the processability of the particle loaded bicomponent fibers was evaluated.

  16. Patterns of self-cutting: a preliminary study on differences in clinical implications between wrist- and arm-cutting using a Japanese juvenile detention center sample.

    PubMed

    Matsumoto, Toshihiko; Yamaguchi, Akiko; Chiba, Yasuhiko; Asami, Takeshi; Iseki, Eizo; Hirayasu, Yoshio

    2004-08-01

    The present study was aimed to clarify the differences in clinical implications between wrist- and arm-cutting. Subjects were 201 delinquent adolescents (178 males and 23 females) who had been admitted to a detention center from February to March 2003. A self-reporting questionnaire and the Adolescent Dissociative Experience Scale (ADES) were given. Traumatic events and other self-injurious behavior were compared among four groups. In total, 33 (16.4%) subjects reported wrist- and/or arm-cutting. Of the females, 60.9% (n = 14) had experienced self cutting behaviors compared to 10.7% of males (n = 19). Subjects were divided into four groups; 'non-cutting' (NC: n = 168, 83.6%), 'wrist-cutting' (WC: n = 5, 2.5%), 'arm-cutting' (AC: n = 19, 9.5%), and 'wrist- and arm-cutting' (WAC: n = 9, 4.5%). WC, AC, and WAC groups reported early separation, bulling in school, and histories of sexual/physical abuse more frequently than NC group. WC and WAC groups reported suicidal ideation and suicide attempts more frequently than NC and AC groups. The ADES scores in AC and WAC groups were significantly higher than in those in NC group (P < 0.001), while the scores in WC were not different from NC groups. WC and WAC groups self-cut due to suicide idea more frequently than the AC group, while AC group self-cut due to anger expression more frequently than WC or WAC groups. Self-cutters experienced early separation, bullying in school, and sexual/physical abuse more frequently than-non-self-cutters. Arm-cutting behavior may predict dissociation, while wrist-cutting may involve with suicidality.

  17. BP pledges to cut emissions

    NASA Astrophysics Data System (ADS)

    Showstack, Randy

    British Petroleum (BP), one of the world's biggest oil companies that could become even bigger if a merger with Amoco is approved, announced on September 18 that it will cut its emissions of greenhouse gases by 10% from a 1990 baseline of 40 million tons of carbon dioxide between now and the year 2010.The target, which is double the amount of emissions reductions that industrialized nations agreed to under the Kyoto protocol on climate change, will now stand next to BP's financial targets, said John Browne, group chief executive of BP.

  18. Clinically lean; "cutting the crap".

    PubMed

    Caldwell, G

    2012-01-01

    Proponents of Lean Philosophy believe that successful businesses must reduce waste in working time and resources to a minimum, and maximise their use in productive work. The productive work of the Acute Medical Unit is to provide effective clinical management to a daily cohort of acutely ill patients. Many Clinicians are cynical about Lean. In this article, Dr Caldwell discusses how many clinicians complain of too much crap in the workplace, which gets in the way of swift, safe high quality clinical care. He argues that "Cutting the Crap" in the Acute Medical Unit is entirely consistent with Lean approaches to management of complex systems.

  19. Free-piston cutting machine

    DOEpatents

    Ciccarelli, Gaby; Subudhi, Manomohan; Hall, Robert E.

    2000-01-01

    A cutting machine includes a gun barrel for receiving a projectile. A compression tube is disposed in flow communication with the barrel and includes a piston therein. A reservoir is disposed in flow communication with the tube and receives a first gas under pressure. A second gas fills the compression tube on a front face of the piston. And, the pressurized first gas is discharged into the tube on a back face of the piston to accelerate the piston through the tube for compressing the second gas, and in turn launching the projectile through the barrel to impact a workpiece.

  20. The suitability of three Galia melon cultivars and different types of cuts for the fresh-cut industry.

    PubMed

    Silveira, Ana C; Aguayo, Encarna; Artés, Francisco

    2013-12-01

    Melons (Cucumis melo L.) are widely cultivated in Mediterranean countries. For fresh-cut melon elaboration, factors such as type of cultivar and cut have a significant impact on final product quality. The quality parameters from long, medium and short shelf-life Galia melon cultivars, cut into different shapes such as slices, trapezoids and cylinders and stored up to 10 days at 5 °C, were evaluated in order to learn the suitability of these cultivars and type of cut for minimal processing. In general, long-life melon cultivar had a low respiration rate and ethylene emissions, and high tissue firmness, but low levels of glucose, fructose, vitamin C and flavor rating by consumers. However, despite having higher metabolic activity and susceptibility to microbial spoilage, the short shelf-life cultivar melon had higher firmness retention. This cultivar was characterized by its richness in glucose, fructose and vitamin C, and its sensory quality (flavor) was highly valued. In general, the medium cultivar had an intermediate behavior between long and short cultivars but without their positive attributes. As a consequence of the most intense damage, the cylindrical shape had higher metabolic activity, susceptibility to microbial spoilage and reduced appearance. In the long and medium-life cultivars studied, low flavor was the limiting factor to extend the shelf-life of fresh-cut melon while for the short-life cultivar the limiting factor was its susceptibility to bacterial growth. Cut types such as cylinders should be avoided. © 2013 Society of Chemical Industry.

  1. Chemical scissors cut phosphorene nanostructures

    NASA Astrophysics Data System (ADS)

    Peng, Xihong; Wei, Qun

    2014-12-01

    Phosphorene, a recently fabricated two-dimensional puckered honeycomb structure of phosphorus, showed promising properties for applications in nano-electronics. In this work, we report a chemical scissors effect on phosphorene, using first-principles method. It was found that chemical species, such as H, OH, F, and Cl, can act as scissors to cut phosphorene. Phosphorus nanochains and nanoribbons can be obtained. The scissors effect results from the strong bonding between the chemical species and phosphorus atoms. Other species such as O, S and Se fail to cut phosphorene nanostructures due to their weak bonding with phosphorus. The electronic structures of the produced P-chains reveal that the hydrogenated chain is an insulator while the pristine chain is a one-dimensional Dirac material, in which the charge carriers are massless fermions travelling at an effective speed of light ˜8 × 105 m s-1. The obtained zigzag phosphorene nanoribbons show either metallic or semiconducting behaviors, depending on the treatment of the edge phosphorus atoms.

  2. Minimum cut and shear bands

    NASA Astrophysics Data System (ADS)

    Tordesillas, Antoinette; Cramer, Andrew; Walker, David M.

    2013-06-01

    We explore the efficacy of network optimisation theory for minimum cut to quantify the evolution of granular fabric and its functionality as a transmission medium in deforming dense granular media. Our focus here is on force transmission in a sheared assembly of polydisperse particles, in a biaxial compression test under constant confining pressure. The granular fabric is examined with respect to the material's force-bearing contact network over that regime when the material has reached its residual strength, and is deforming under a near constant volume in the presence of a fully developed shear band. The structural evolution of the fabric is quantitatively characterized using a representative weighted-directed network that is similarly evolving as the sample deforms. The edges or links, representing the interparticle contacts, are each weighted by the capacity of the contact to transmit force: a scalar that depends solely on the relative motion of the contacting grains. In the large strain failure regime, the minimum cut which represents the bottleneck in force transmission is found to lie in the persistent shear band. This study paves the way for the future analysis of flows and force transmission through an evolving contact network and, in turn, the characterisation of the relationship between the material's contact topology and its capacity to transmit forces through its contact network.

  3. President's budget concerns advocates. Prevention money cuts are dark omen.

    PubMed

    2005-04-01

    President George W. Bush expressed support for the reauthorization of the Ryan White Care Act in his State of the Union address, but his budget for the 2006 fiscal year provided mostly flat funding with cuts in prevention activities, a sign that trouble is ahead for state budgets and AIDS service organizations struggling to provide prevention, care, and other services to growing HIV populations, AIDS advocates say.

  4. Flux cutting in high- Tc superconductors

    SciTech Connect

    Vlasko-Vlasov, V.; Koshelev, A.; Glatz, A.; Phillips, C.; Welp, U.; Kwok, W.

    2015-01-01

    We performed magneto-optical study of flux distributions in a YBCO crystal under various applied crossed- field orientations to elucidate the complex nature of magnetic flux cutting in superconductors. Our study reveals unusual vortex patterns induced by the interplay between flux-cutting and vortex pinning. We observe strong flux penetration anisotropy of the normal flux B⊥ in the presence of an in-plane field H|| and associate the modified flux dynamics with staircase structure of tilted vortices in YBCO and the flux-cutting process. We demonstrate that flux-cutting can effectively delay vortex entry in the direction transverse to H||. Finally, we elucidate details of the vortex-cutting and reconnection process using time-dependent Ginzburg-Landau simulations.

  5. Fibre laser cutting stainless steel: Fluid dynamics and cut front morphology

    NASA Astrophysics Data System (ADS)

    Pocorni, Jetro; Powell, John; Deichsel, Eckard; Frostevarg, Jan; Kaplan, Alexander F. H.

    2017-01-01

    In this paper the morphology of the laser cut front generated by fibre lasers was investigated by observation of the 'frozen' cut front, additionally high speed imaging (HSI) was employed to study the fluid dynamics on the cut front while cutting. During laser cutting the morphology and flow properties of the melt film on the cut front affect cut quality parameters such as cut edge roughness and dross (residual melt attached to the bottom of the cut edge). HSI observation of melt flow down a laser cutting front using standard cutting parameters is experimentally problematic because the cut front is narrow and surrounded by the kerf walls. To compensate for this, artificial parameters are usually chosen to obtain wide cut fronts which are unrepresentative of the actual industrial process. This paper presents a new experimental cutting geometry which permits HSI of the laser cut front using standard, commercial parameters. These results suggest that the cut front produced when cutting medium section (10 mm thick) stainless steel with a fibre laser and a nitrogen assist gas is covered in humps which themselves are covered by a thin layer of liquid. HSI observation and theoretical analysis reveal that under these conditions the humps move down the cut front at an average speed of approximately 0.4 m/s while the covering liquid flows at an average speed of approximately 1.1 m/s, with an average melt depth at the bottom of the cut zone of approximately 0.17 mm.

  6. Does cutting of mugwort stands affect airborne pollen concentrations?

    PubMed

    Rantio-Lehtimäki, A; Helander, M L; Karhu, K

    1992-08-01

    Pollen of mugwort (Artemisia vulgaris L.) is the most important allergenic pollen in urban areas of south and central Finland in late summer. The purpose of this study was to investigate, experimentally, whether the cutting of mugwort stands affects its airborne pollen concentrations. Experimental plots were either cut (4 plots) or uncut (4 plots) in 2 previous seasons: 4 of them were small (less than 0.5 hectare) and 4 large (greater than 5 hectares). Finally, the plots were divided randomly into 2 groups according to a third variable, cutting in the study season, 1989. Samples were taken on 2 rainless mornings at the peak mugwort flowering time. Two rotorod type samplers were used at heights of 1 and 2 m from ground level, simulating the inhalation heights of children and adults, respectively. The results indicate that cutting mugwort stands significantly reduces airborne pollen concentrations, but the treated areas have to be large, since in the town area there are plenty of mugwort pollen sources. The pollen concentrations at the 2 heights tested did not differ significantly.

  7. Monitoring Method of Cutting Force by Using Additional Spindle Sensors

    NASA Astrophysics Data System (ADS)

    Sarhan, Ahmed Aly Diaa; Matsubara, Atsushi; Sugihara, Motoyuki; Saraie, Hidenori; Ibaraki, Soichi; Kakino, Yoshiaki

    This paper describes a monitoring method of cutting forces for end milling process by using displacement sensors. Four eddy-current displacement sensors are installed on the spindle housing of a machining center so that they can detect the radial motion of the rotating spindle. Thermocouples are also attached to the spindle structure in order to examine the thermal effect in the displacement sensing. The change in the spindle stiffness due to the spindle temperature and the speed is investigated as well. Finally, the estimation performance of cutting forces using the spindle displacement sensors is experimentally investigated by machining tests on carbon steel in end milling operations under different cutting conditions. It is found that the monitoring errors are attributable to the thermal displacement of the spindle, the time lag of the sensing system, and the modeling error of the spindle stiffness. It is also shown that the root mean square errors between estimated and measured amplitudes of cutting forces are reduced to be less than 20N with proper selection of the linear stiffness.

  8. Effects of heat on cut mark characteristics.

    PubMed

    Waltenberger, Lukas; Schutkowski, Holger

    2017-02-01

    Cut marks on bones provide crucial information about tools used and their mode of application, both in archaeological and forensic contexts. Despite a substantial amount of research on cut mark analysis and the influence of fire on bones (shrinkage, fracture pattern, recrystallisation), there is still a lack of knowledge in cut mark analysis on burnt remains. This study provides information about heat alteration of cut marks and whether consistent features can be observed that allow direct interpretation of the implemented tools used. In a controlled experiment, cut marks (n=25) were inflicted on pig ribs (n=7) with a kitchen knife and examined using micro-CT and digital microscopy. The methods were compared in terms of their efficacy in recording cut marks on native and heat-treated bones. Statistical analysis demonstrates that floor angles and the maximum slope height of cuts undergo significant alteration, whereas width, depth, floor radius, slope, and opening angle remain stable. Micro-CT and digital microscopy are both suitable methods for cut mark analysis. However, significant differences in measurements were detected between both methods, as micro-CT is less accurate due to the lower resolution. Moreover, stabbing led to micro-fissures surrounding the cuts, which might also influence the alteration of cut marks.

  9. Iron regulation of gene expression in the Bradyrhizobium japonicum/soybean symbiosis. Final technical report, June 1, 1991--May 31, 1995

    SciTech Connect

    Guerinot, M.L.

    1996-02-08

    B.japonicum produces ALA in a reaction catalyzed by the product of the hemA gene. Expression of the gene is affected by iron availability. To address the question of how the 5 prime untranslated region of the hemA transcript is involved in iron regulation, evenly spaced 10bp deletions within the hemA leader region was constructed and effects on hemA-lacZ expression were determined.

  10. Final Report

    SciTech Connect

    Gurney, Kevin R.

    2015-01-12

    This document constitutes the final report under DOE grant DE-FG-08ER64649. The organization of this document is as follows: first, I will review the original scope of the proposed research. Second, I will present the current draft of a paper nearing submission to Nature Climate Change on the initial results of this funded effort. Finally, I will present the last phase of the research under this grant which has supported a Ph.D. student. To that end, I will present the graduate student’s proposed research, a portion of which is completed and reflected in the paper nearing submission. This final work phase will be completed in the next 12 months. This final workphase will likely result in 1-2 additional publications and we consider the results (as exemplified by the current paper) high quality. The continuing results will acknowledge the funding provided by DOE grant DE-FG-08ER64649.

  11. Final Report

    SciTech Connect

    DeTar, Carleton

    2012-12-10

    This document constitutes the Final Report for award DE-FC02-06ER41446 as required by the Office of Science. It summarizes accomplishments and provides copies of scientific publications with significant contribution from this award.

  12. Simplifier cut core inductor design

    NASA Technical Reports Server (NTRS)

    Mclyman, W. T.

    1976-01-01

    Advantages of specifying C cores and cut toroids fabricated from grain oriented silicon steels for use in high frequency power converters and pulse width modulated switching regulators are discussed. A method for rating cores assigns to each core a number which is the product of its window and core cross section area, called 'Area Product A sub p.' A correlation between the A sub p numbers and current density for a given temperature rise was developed. Also, straight line relationships were developed for A sub p and volume, A sub p and surface area, and A sub p and weight. These relationships can be used to simplify and standardize the process of inductor design. They also make it possible to design inductors of small bulk and volume or to optimize efficiency.

  13. Cut performance levels and testing.

    PubMed

    Bennett, Bill; Moreland, Jeff

    2011-11-01

    While the ISEA performance levels and general recommendations detailed above can help tp provide guidance when selecting hand protection products, the responsibility for testing products for specific end-user applications still rests with the end user. We can indicate, for example, that a medium-weight, uncoated Kevlar glove will typically have an ISEA cut rating of 3, but we cannot say the glove will provide the level of protection needed for the range of jobs on an automobile assembly line. Another Level 3 glove might be better suited to an application the require the worker to have an oil grip. As glove manufacturers, we know gloves. We do not know the details about every workplace. We therefore, must look to our customers to provide us the properties they need for hand protection products that will sufficiently protect their workers on the job.

  14. SLSL Ribbon-cutting Ceremony

    NASA Image and Video Library

    2003-11-19

    The Honorable Toni Jennings, lieutenant governor of the state of Florida, speaks at a dedication and ribbon-cutting ceremony for the Space Life Sciences Lab hosted by NASA-Kennedy Space Center and the state of Florida at the new lab. Completed in August, the facility encompasses more than 100,000 square feet and was formerly known as the Space Experiment Research and Processing Laboratory or SERPL. The state, through the Florida Space Authority, built the research lab which is host to NASA, NASA’s Life Sciences Services contractor Dynamac Corp., Bionetics Corp., and researchers from the University of Florida. Dynamac Corp. leases the facility. The Florida Space Research Institute is responsible for gaining additional tenants from outside the NASA community.

  15. Demonstration project cuts red tape

    NASA Astrophysics Data System (ADS)

    Katzoff, Judith A.

    Results from a demonstration project aimed at cutting red tape in federal grants for basic research at universities are "very encouraging" so far, according to Don I. Phillips, executive director of the Government-University-Industry Research Roundtable. The roundtable is coordinating the experimental effort, with the participation of five major federal agencies as well as the Florida state university system and the University of Miami (a private institution in Coral Gables, Fla.).Under the project, special conditions apply to grants from the participating agencies to individual researchers at the participating universities: Investigators do not have to ask the agency's permission for changes in budget allocations, purchases of permanent equipment, or foreign travel. Grant money can be spent up to a year after the grant ends without a special request. Under this plan, researchers, with agency approval, can also ask to have their entire research program covered as a single administrative entity, rather than as several individual projects.

  16. Drag blade bit with diamond cutting elements

    SciTech Connect

    Radtke, R. P.; Morris, W. V.

    1985-02-19

    A drag blade bit for connection on a drill string has a hollow body on which there are welded a plurality of cutting or drilling blades. The blades extend longitudinally and radially of the bit body and terminate in relatively flat, radially extending cutting edges. A plurality of cutters are positioned in and spaced along the cutting edges and consists of cylindrical sintered carbide inserts with polycrystalline diamond cutting elements mounted thereon. Hardfacing is provided on the cutting edges between the cutters and on the other surfaces of the blades and the bit body subject to abrasive wear. One or more nozzles are positioned in passages from the interior of the bit body for directing flow of drilling fluid for flushing cuttings from the well bore and for cooling the bit.

  17. New Modelling Strategies For Metal Cutting

    SciTech Connect

    Rosa, Pedro A. R.; Martins, Paulo A. F.; Atkins, Anthony G.

    2007-05-17

    This paper draws from the 'plasticity and friction only' view of metal cutting to the presentation of new modelling strategies based on the interaction between finite elements and modern ductile fracture mechanics. The overall presentation is supported by specially designed orthogonal metal cutting experiments that were performed on Lead test specimens under laboratory-controlled conditions. Comparisons between theoretical predictions and experimental results comprise a wide range of topics such as material flow, cutting forces and specific cutting pressure. The paper demonstrates that while material flow and chip formation can be successfully modelled by traditional 'plasticity and friction only' analyses, the contribution of the fracture work involved in the formation of new surfaces is essential for obtaining good estimates of cutting forces and of the specific cutting pressure.

  18. Rapid Runway Repair Program Subtask 1.07 - Rapid Concrete Cutting.

    DTIC Science & Technology

    1983-06-01

    AD-Rl3i 771 RRPID RUNWAY’REPAIR PROGRAM SUBTA5K 187 - RAPID 1/3 CONCRETE CUTTING (U) 8DM CORP MCLEAN YVA RKMOATS ET IL. JUN 83 8DM/W-82-778 TR 7...I RAPID RUNWAY REPAIR PROGRAM SUBTASK 1.07 - RAPID CONCRETE CUTTING MOATS, R.K. [BOM), WANG, F.D., DEARS, WILLIAM (ENGINEERING & SCIENCE TECHNOLOGY...Program Final Technical ReportMarch 1982 - January 1983 -’’ • Subtask 1.07 - Rapid Concrete Cutting 1982N - Janury 1983 6. PERFORMING ORG. REPORT NUMBER

  19. Cutting sound enhancement system for mining machines

    DOEpatents

    Leigh, Michael C.; Kwitowski, August J.

    1992-01-01

    A cutting sound enhancement system (10) for transmitting an audible signal from the cutting head (101) of a piece of mine machinery (100) to an operator at a remote station (200), wherein, the operator using a headphone unit (14) can monitor the difference in sounds being made solely by the cutting head (101) to determine the location of the roof, floor, and walls of a coal seam (50).

  20. Control of red alder by cutting.

    Treesearch

    Dean S. DeBell; Thomas C. Turpin

    1989-01-01

    Effects of tree age, month of cut, and height and angle of cut on sprouting of red alder stumps were evaluated in a study designed to develop an effective method for controlling red alder in Douglas-fir plantations. Ninety-five percent or more of alder stumps cut in June or July died by the end of the next growing season; mortality was 88, 70, and 22 percent for stumps...

  1. Enclosed Cutting-And-Polishing Apparatus

    NASA Technical Reports Server (NTRS)

    Rossier, R. N.; Bicknell, B.

    1989-01-01

    Proposed apparatus cuts and polishes specimens while preventing contamination of outside environment or of subsequent specimens processed in it. Designed for use in zero gravity but also includes features useful in cutting and polishing of toxic or otherwise hazardous materials on Earth. Includes remote manipulator for handling specimens, cutting and polishing wire, inlets for gas and liquid, and outlets for waste liquid and gas. Replaceable plastic liner surrounds working space.

  2. Alternative Metal Hot Cutting Operations for Opacity

    DTIC Science & Technology

    2014-10-01

    Distribution A: Approved for public release; distribution is unlimited. TDS-NAVFAC-EXWC-EV-1509 October 2014 Alternative Metal Hot Cutting ...for oxy-fuel cutting of metal, to reduce opacity emissions during shipbreaking and recycling operations. When ships and submarines reach the end...vessels utilizes oxy-fuel metal cutting . However, this process generates visible particulate matter that has the potential to exceed local air

  3. Enclosed Cutting-And-Polishing Apparatus

    NASA Technical Reports Server (NTRS)

    Rossier, R. N.; Bicknell, B.

    1989-01-01

    Proposed apparatus cuts and polishes specimens while preventing contamination of outside environment or of subsequent specimens processed in it. Designed for use in zero gravity but also includes features useful in cutting and polishing of toxic or otherwise hazardous materials on Earth. Includes remote manipulator for handling specimens, cutting and polishing wire, inlets for gas and liquid, and outlets for waste liquid and gas. Replaceable plastic liner surrounds working space.

  4. Error analysis of corner cutting algorithms

    NASA Astrophysics Data System (ADS)

    Mainar, E.; Peña, J. M.

    1999-10-01

    Corner cutting algorithms are used in different fields and, in particular, play a relevant role in Computer Aided Geometric Design. Evaluation algorithms such as the de Casteljau algorithm for polynomials and the de Boor-Cox algorithm for B-splines are examples of corner cutting algorithms. Here backward and forward error analysis of corner cutting algorithms are performed. The running error is also analyzed and as a consequence the general algorithm is modified to include the computation of an error bound.

  5. Correlated mRNAs and miRNAs from co-expression and regulatory networks affect porcine muscle and finally meat properties.

    PubMed

    Ponsuksili, Siriluck; Du, Yang; Hadlich, Frieder; Siengdee, Puntita; Murani, Eduard; Schwerin, Manfred; Wimmers, Klaus

    2013-08-05

    Physiological processes aiding the conversion of muscle to meat involve many genes associated with muscle structure and metabolic processes. MicroRNAs regulate networks of genes to orchestrate cellular functions, in turn regulating phenotypes. We applied weighted gene co-expression network analysis to identify co-expression modules that correlated to meat quality phenotypes and were highly enriched for genes involved in glucose metabolism, response to wounding, mitochondrial ribosome, mitochondrion, and extracellular matrix. Negative correlation of miRNA with mRNA and target prediction were used to select transcripts out of the modules of trait-associated mRNAs to further identify those genes that are correlated with post mortem traits. Porcine muscle co-expression transcript networks that correlated to post mortem traits were identified. The integration of miRNA and mRNA expression analyses, as well as network analysis, enabled us to interpret the differentially-regulated genes from a systems perspective. Linking co-expression networks of transcripts and hierarchically organized pairs of miRNAs and mRNAs to meat properties yields new insight into several biological pathways underlying phenotype differences. These pathways may also be diagnostic for many myopathies, which are accompanied by deficient nutrient and oxygen supply of muscle fibers.

  6. Effect of year and cutting on equations for estimating net energy of alfalfa forage.

    PubMed

    Belyea, R; Restrepo, R; Martz, F; Ellersieck, M

    1999-09-01

    The net energy of lactation (NEL) concentration of forages is important for formulating diets. The equations presently used to estimate NEL of alfalfa are based on limited data. Our objective was to determine whether a larger database would provide more relevant equations. One hundred eighty samples of alfalfa were taken over four cuttings and 2 yr, combined into 45 composites and analyzed for neutral detergent fiber, acid detergent fiber (ADF), and in vitro true digestibility. Finally, NEL values were estimated using neutral detergent fiber and in vitro true digestibility. Prediction equations were obtained by regressing NEL upon ADF concentration. Changes in NEL with age of alfalfa at harvest differed with year and cutting. Estimation of NEL would be more accurate with equations specific for cutting and year, but such an approach would be difficult to use in practice. When data were pooled across years, four cutting-specific equations were obtained; these had different intercepts and slopes and gave different NEL values for a given ADF content. Differences among estimates of NEL increased as ADF increased. Data were combined across years and cuttings to give an overall equation that was similar to published prediction equations. Compared with NEL values from the cutting-specific equations, the overall equation underestimated NEL for first cutting alfalfa and overestimated NEL of second cutting alfalfa. A lack of precision in estimating NEL could equate to 1.5 to 2.5 kg of milk/d. Cutting specific equations should be used to estimate the NEL of first- and second-cutting alfalfa; NEL of the third and fourth cuttings could be estimated using an overall equation.

  7. Energy characteristics of cutting of thick steel sheets by a CO2 and fiber laser

    NASA Astrophysics Data System (ADS)

    Orishich, A. M.; Shulyatyev, V. B.; Malikov, A. G.; Golishev, A. A.

    2013-02-01

    Oxygen-assisted laser cutting of low-carbon steel with a fiber laser is studied experimentally. The objective of the work is to find the link between the cutting quality (which is low roughness and no dross) and energy characteristics of the cutting. Cutting parameters are expressed though two dimensionless complexes, namely the Peclet number and dimensionless laser power. It is founded that for the cutting with minimal roughness, the Peclet number is of 0.35…0.4, and the contribution of the absorbed laser energy in the unit of removed material volume is 12…14 J/mm3 for sheets of 3, 5, and 10 mm. The results are compared to the data obtained for the СО2 laser.

  8. Exploring cut-off values for large waist circumference in older adults: a new methodological approach.

    PubMed

    Heim, N; Snijder, M B; Heymans, M W; Deeg, D J H; Seidell, J C; Visser, M

    2010-04-01

    There is an ongoing debate about the applicability of current criteria for large waist circumference (WC) in older adults. Our aim was to explore cut-off values for large WC in adults aged 70 years and older, using previously used and new methods. Prospective cohort study. Data of 1049 participants of the Longitudinal Aging Study Amsterdam (LASA) (1995-1996), aged 70-88y, were used. Measured BMI and WC, and self-reported mobility limitations. Linear regression analyses showed that the values of WC corresponding to BMI of 25kg/m2 and 30kg/m2 were higher than the current cut-offs. Cut-offs found in men were 97 and 110cm, whereas 88 and 98cm represented the cut-offs in women. Areas under the Receiver Operating Characteristic (ROC) curves showed that the accuracy to predict mobility limitations improved when the higher cut-offs were applied. Spline regression curves showed that the relationship of WC with mobility limitations was U-shaped in men, while in women, the risk for mobility limitations increased gradually with increasing WC. However, at the level of current cut-off values for WC the odds for mobility limitations were not increased. Based on results of extensive analyses, this study suggests that the cut-offs for large WC should be higher when applied to older adults. The association of WC with other negative health outcomes needs to be investigated to establish the final cut-points.

  9. A High Performance Sensor for Triaxial Cutting Force Measurement in Turning

    PubMed Central

    Zhao, You; Zhao, Yulong; Liang, Songbo; Zhou, Guanwu

    2015-01-01

    This paper presents a high performance triaxial cutting force sensor with excellent accuracy, favorable natural frequency and acceptable cross-interference for high speed turning process. Octagonal ring is selected as sensitive element of the designed sensor, which is drawn inspiration from ring theory. A novel structure of two mutual-perpendicular octagonal rings is proposed and three Wheatstone full bridge circuits are specially organized in order to obtain triaxial cutting force components and restrain cross-interference. Firstly, the newly developed sensor is tested in static calibration; test results indicate that the sensor possesses outstanding accuracy in the range of 0.38%–0.83%. Secondly, impacting modal tests are conducted to identify the natural frequencies of the sensor in triaxial directions (i.e., 1147 Hz, 1122 Hz and 2035 Hz), which implies that the devised sensor can be used for cutting force measurement in a high speed lathe when the spindle speed does not exceed 17,205 rev/min in continuous cutting condition. Finally, an application of the sensor in turning process is operated to show its performance for real-time cutting force measurement; the measured cutting forces demonstrate a good accordance with the variation of cutting parameters. Thus, the developed sensor possesses perfect properties and it gains great potential for real-time cutting force measurement in turning. PMID:25855035

  10. Optimization of CO2 laser cutting parameters on Austenitic type Stainless steel sheet

    NASA Astrophysics Data System (ADS)

    Parthiban, A.; Sathish, S.; Chandrasekaran, M.; Ravikumar, R.

    2017-03-01

    Thin AISI 316L stainless steel sheet widely used in sheet metal processing industries for specific applications. CO2 laser cutting is one of the most popular sheet metal cutting processes for cutting of sheets in different profile. In present work various cutting parameters such as laser power (2000 watts-4000 watts), cutting speed (3500mm/min – 5500 mm/min) and assist gas pressure (0.7 Mpa-0.9Mpa) for cutting of AISI 316L 2mm thickness stainless sheet. This experimentation was conducted based on Box-Behenken design. The aim of this work is to develop a mathematical model kerf width for straight and curved profile through response surface methodology. The developed mathematical models for straight and curved profile have been compared. The Quadratic models have the best agreement with experimental data, and also the shape of the profile a substantial role in achieving to minimize the kerf width. Finally the numerical optimization technique has been used to find out best optimum laser cutting parameter for both straight and curved profile cut.

  11. A Distance-Weighted Graph-Cut Method for the Segmentation of Laser Point Clouds

    NASA Astrophysics Data System (ADS)

    Dutta, A.; Engels, J.; Hahn, M.

    2014-08-01

    Normalized Cut according to (Shi and Malik 2000) is a well-established divisive image segmentation method. Here we use Normalized Cut for the segmentation of laser point clouds in urban areas. In particular we propose an edge weight measure which takes local plane parameters, RGB values and eigenvalues of the covariance matrices of the local point distribution into account. Due to its target function, Normalized Cut favours cuts with "small cut lines/surfaces", which appears to be a drawback for our application. We therefore modify the target function, weighting the similarity measures with distant-depending weights. We call the induced minimization problem "Distance-weighted Cut" (DWCut). The new target function leads to a slightly more complicated generalized eigenvalue problem than in case of the Normalized Cut; on the other hand, the new target function is easier to interpret and avoids the just-mentioned drawback. DWCut can be beneficially combined with an aggregation in order to reduce the computational effort and to avoid shortcomings due to insufficient plane parameters. Finally we present examples for the successful application of the Distance-weighted Cut principle. The method was implemented as a plugin into the free and open source geographic information system SAGA; for preprocessing steps the proprietary SAGA-based LiDAR software LIS was applied.

  12. Female genital cutting in Hargeisa, Somaliland: is there a move towards less severe forms?

    PubMed

    Lunde, Ingvild Bergom; Sagbakken, Mette

    2014-05-01

    According to several sources, little progress is being made in eliminating the cutting of female genitalia. This paper, based on qualitative interviews and observations, explores perceptions of female genital cutting and elimination of the phenomenon in Hargeisa, Somaliland. Two main groups of participants were interviewed: (1) 22 representatives of organisations whose work directly relates to female genital cutting; and (2) 16 individuals representing different groups of society. It was found that there is an increasing use of medical staff and equipment when a girl undergoes the procedure of female genital cutting; the use of terminology is crucial in understanding current perceptions of female genital cutting; religion is both an important barrier and facilitator of elimination; and finally, traditional gender structures are currently being challenged in Hargeisa. The findings of this study suggest that it is important to consider current perceptions on practices of female genital cutting and on abandonment of female genital cutting, in order to gain useful knowledge on the issue of elimination. The study concludes that elimination of female genital cutting is a multifaceted process which is constantly negotiated in a diversity of social settings. Copyright © 2014 Reproductive Health Matters. Published by Elsevier Ltd. All rights reserved.

  13. A high performance sensor for triaxial cutting force measurement in turning.

    PubMed

    Zhao, You; Zhao, Yulong; Liang, Songbo; Zhou, Guanwu

    2015-04-03

    This paper presents a high performance triaxial cutting force sensor with excellent accuracy, favorable natural frequency and acceptable cross-interference for high speed turning process. Octagonal ring is selected as sensitive element of the designed sensor, which is drawn inspiration from ring theory. A novel structure of two mutual-perpendicular octagonal rings is proposed and three Wheatstone full bridge circuits are specially organized in order to obtain triaxial cutting force components and restrain cross-interference. Firstly, the newly developed sensor is tested in static calibration; test results indicate that the sensor possesses outstanding accuracy in the range of 0.38%-0.83%. Secondly, impacting modal tests are conducted to identify the natural frequencies of the sensor in triaxial directions (i.e., 1147 Hz, 1122 Hz and 2035 Hz), which implies that the devised sensor can be used for cutting force measurement in a high speed lathe when the spindle speed does not exceed 17,205 rev/min in continuous cutting condition. Finally, an application of the sensor in turning process is operated to show its performance for real-time cutting force measurement; the measured cutting forces demonstrate a good accordance with the variation of cutting parameters. Thus, the developed sensor possesses perfect properties and it gains great potential for real-time cutting force measurement in turning.

  14. Machining Challenges: Macro to Micro Cutting

    NASA Astrophysics Data System (ADS)

    Shunmugam, M. S.

    2016-04-01

    Metal cutting is an important machining operation in the manufacture of almost all engineering components. Cutting technology has undergone several changes with the development of machine tools and cutting tools to meet challenges posed by newer materials, complex shapes, product miniaturization and competitive environments. In this paper, challenges in macro and micro cutting are brought out. Conventional and micro end-milling are included as illustrative examples and details are presented along with discussion. Lengthy equations are avoided to the extent possible, as the emphasis is on the basic concepts.

  15. Stabilisation/solidification of synthetic petroleum drill cuttings.

    PubMed

    Al-Ansary, Marwa S; Al-Tabbaa, Abir

    2007-03-15

    This paper presents the results of an experimental investigation into the use of stabilisation/solidification (S/S) to treat synthetic drill cuttings as a pre-treatment to landfilling or for potential re-use as construction products. Two synthetic mixes were used based on average concentrations of specific contaminates present in typical drill cuttings from the North Sea and the Red Sea areas. The two synthetic drill cuttings contained similar chloride content of 2.03% and 2.13% by weight but different hydrocarbon content of 4.20% and 10.95% by weight, respectively; hence the mixes were denoted as low and high oil content mixes, respectively. A number of conventional S/S binders were tested including Portland cement (PC), lime and blast-furnace slag (BFS), in addition to novel binders such as microsilica and magnesium oxide cement. Physical, chemical and microstructural analyses were used to compare the relative performance of the different binder mixes. The unconfined compressive strength (UCS) values were observed to cover a wide range depending on the binder used. Despite the significant difference in the hydrocarbon content in the two synthetic cuttings, the measured UCS values of the mixes with the same binder type and content were similar. The leachability results showed the reduction of the synthetic drill cuttings to a stable non-reactive hazardous waste, compliant with the UK acceptance criteria for non-hazardous landfills: (a) by most of the binders for chloride concentrations, and (b) by the 20% BFS-PC and 30% PC binders for the low oil content mix. The 30% BFS-PC binder successfully reduced the leached oil concentration of the low oil content mix to inert levels. Finally, the microstructural analysis offered valuable information on the morphology and general behaviour of the mixes that were not depicted by the other tests.

  16. National Academy of Sciences and Academy of Sciences of the USSR workshop on structure of the eucaryotic genome and regulation of its expression. Final report

    SciTech Connect

    Not Available

    1990-12-31

    This report provides a brief overview of the Workshop on Structure of the Eukaryotic Genome and Regulation of its Expression held in Tbilisi, Georgia, USSR. The report describes the presentations made at the meeting but also goes on to describe the state of molecular biology and genetics research in the Soviet Union and makes recommendations on how to improve future such meetings.

  17. The Media and Children's Issues. Final Report on the Children's Express Symposium III (New York, New York, June 11-12, 1990).

    ERIC Educational Resources Information Center

    Children's Express Foundation, Inc., New York, NY.

    This document is a report of the Children's Express Symposium III, a forum for journalists on children's issues. Included in the report are the comments of news media executives, journalists, broadcasters, experts on children's issues, directors of children's programs, and young people affected by the policies and practices discussed. Opening…

  18. Laser cutting of triangular geometries in aluminum foam: Effect of cut size on thermal stress levels

    NASA Astrophysics Data System (ADS)

    Yilbas, B. S.; Akhtar, S. S.; Keles, O.

    2013-06-01

    Laser cutting of triangle shaped geometries in aluminum foam is carried out and the influence of triangle size on temperature and stress fields is examined. ABAQUS finite element code is used to simulate temperature and stress fields in the cut sections in line with the experimental conditions. Laser cut sections are examined incorporating optical and scanning electron microscopes, and energy dispersive spectroscopy. It is found that small size triangle cut results in relatively higher temperatures around the cut edges as compared to large size triangle cut; however, opposite is true for von Mises stress. This is attributed to the slow cooling rate in the case of the small size triangle cuts. Laser cut surfaces are free from large defects and locally scattered small dross attachment are found at the kerf exit.

  19. Effect of Cutting Angle and Depth of Cut on the Occurrence of Chipped Grain on Sycamore

    Treesearch

    Harold A. Stewart

    1970-01-01

    Sycamore specimens were planned with various combinations of depths of cut and rake angles. Depths of cut up to 1/16 inch had no significant effect on the occurrence of chipped grain in sycamore but rake angle did.

  20. The effect of cutting speed on residual stresses when orthogonal cutting TC4

    NASA Astrophysics Data System (ADS)

    Liu, Chaofeng; Wang, Zengqiang; Zhang, Guang; Liu, Lei

    2015-09-01

    As one of the most important parameters in mental cutting, cutting speed has a significant influence on residual stress. Finite element method and experiment method are used to study the relationship between cutting speed and residual stress when orthogonal cutting TC4 titanium alloy. The result of simulation and experiment shows that: when the cutting speed is low, the residual stress in axial direction is compressive stress and gradually converts to tensile stress with the increase of cutting speed, but it will convert to compressive stress again if the cutting speed continues to increase; the residual stress in tangential direction is constant to compressive stress and it will decrease with the increase of cutting speed.

  1. Expression and localization of members of the thrombospondin family during final follicle maturation and corpus luteum formation and function in the bovine ovary

    PubMed Central

    BERISHA, Bajram; SCHAMS, Dieter; RODLER, Daniela; SINOWATZ, Fred; PFAFFL, Michael W.

    2016-01-01

    The aim of this study was to characterize the expression patterns and localization of the thrombospondin family members (THBS1, THBS2) and their receptors (CD36 and CD47) in bovine ovaries. First, the antral follicles were classified into 5 groups based on the follicle size and estradiol-17beta (E2) concentration in the follicular fluid (< 0.5, 0.5–5, 5–40, 40–180 and >180 E2 ng/ml). Second, the corpus luteum (CL) was assigned to the following stages: days 1–2, 3–4, 5–7, 8–12, 13–16 and >18 of the estrous cycle and of pregnancy (month 1–2, 3–4, 6–7 and > 8). Third, the corpora lutea were collected by transvaginal ovariectomy before and 0.5, 2, 4, 12, 24, 48 and 64 h after inducing luteolysis by injecting a prostaglandin F2alpha analog. The mRNA expression of examined factors was measured by RT-qPCR, steroid hormone concentration by EIA, and localization by immunohistochemistry. The mRNA expression of THBS1, THBS2, CD36, and CD47 in the granulosa cells and theca interna was high in the small follicles and reduced in the preovulatory follicles. The mRNA expression of THBS1, THBS2, and CD47 in the CL during the estrous cycle was high, but decreased significantly during pregnancy. After induced luteolysis, thrombospondins increased significantly to reach the maximum level at 12 h for THBS1, 24 h for THBS2, and 48 h for CD36. The temporal expression and localization pattern of the thrombospondins and their specific receptors in the antral follicles and corpora lutea during the different physiological phases of the estrous cycle and induced luteolysis appear to be compatible with their inhibitory role in the control of ovarian angiogenesis. PMID:27396384

  2. Laser cutting of pressed explosives: Revision 1

    SciTech Connect

    Roeske, F., Jr.; Banks, R.E.; Armstrong, J.P.; Feit, M.D.; Lee, R.S.; Perry, M.D.; Stuart, B.C.

    1998-05-04

    We have used a femtosecond laser beam to make cuts through small pressed pellets of six common explosives. The laser system, which produces 100 fs pulses of 820 nm light at a repitition rate of 1 kHz, was intitially developed for cutting metal. The advantage of using a femtosecond laser for cutting is that the cutting process transfers virtually no heat to the material that is being cut and produces almost no waste. We used LX-16 explosive (96% PETN/4% FPC 461 binder) for out intial experiments because PETN is one of the most sensitve of the secondary explosives. In some of the experiments the beam first cut through the HE pellet and then through a stainless steel substrate and in other experiments the beam first cut through the stainless steel and then through the pellet. We also cut through pellets that were not backed by a substrate. No evidence of reaction was observed in any of the LX-16 pellets. In addition to LX-16 we cut pellets of LX-14 (95.5% HMX/4.5% Estane), LX-15 (95% HNS/5% Kel-F), LX-17 (92.5% TATB/7.5% Kel-F), PBX-9407 (94% RDX/6% Exon 461), and pressed TNT with no evidence of reaction. The HE was easily cut at low power levels with one or two sweeps at 0.5 W average power sufficing to cut most of the pellets. There is obvioulsy much more work to be done before laser machining of explosives becomes a reality, but the results of these intitial experiments indicate that laser machining of explosives may be an attractive option for explosives processing.

  3. Effect of Cutting Age on the Resistance of Prunus cerasifera (Myrobalan Plum) to Meloidogyne arenaria.

    PubMed

    Esmenjaud, D; Minot, J C; Voisin, R; Salesses, G; Bonnet, A

    1995-12-01

    The response of softwood cuttings of Myrobalan plum infested after 50 and 105 days with 3,000 second-stage juveniles (J2) of Meloidogyne arenaria was compared to 15-month-old hardwood cuttings in 13 genotypes ranging from highly resistant to susceptible. Gall index and number of galls were recorded 30 days after infestation. Fifty-day-old cuttings rooted in perlite developed many rootlets, but had only incipient galls after infestation. In sand, rooting of 50-day-old cuttings not treated with indolebutyric acid (IBA) hormone was so variable that their resistance could not be assessed. Similar cuttings rooted with IBA developed more galls, but neither number of galls per plant nor gall index was a reliable criterion for determination of host suitability. Because of the better rooting results with IBA treatment, 105-day-old cuttings were first rooted with IBA in perlite and then transferred into sand for nematode inoculation. Known highly resistant genotypes of Myrobalan plum were gall-free and the responses of other genotypes paralleled that of the reference hardwood cuttings, although the test was less discriminating. Expression of M. arenaria host suitability in Myrobalan plum depends on root tissue maturation and cannot be reliably evaluated with 50-day-old cuttings.

  4. Effect of Cutting Age on the Resistance of Prunus cerasifera (Myrobalan Plum) to Meloidogyne arenaria

    PubMed Central

    Esmenjaud, D.; Minot, J. C.; Voisin, R.; Salesses, G.; Bonnet, A.

    1995-01-01

    The response of softwood cuttings of Myrobalan plum infested after 50 and 105 days with 3,000 second-stage juveniles (J2) of Meloidogyne arenaria was compared to 15-month-old hardwood cuttings in 13 genotypes ranging from highly resistant to susceptible. Gall index and number of galls were recorded 30 days after infestation. Fifty-day-old cuttings rooted in perlite developed many rootlets, but had only incipient galls after infestation. In sand, rooting of 50-day-old cuttings not treated with indolebutyric acid (IBA) hormone was so variable that their resistance could not be assessed. Similar cuttings rooted with IBA developed more galls, but neither number of galls per plant nor gall index was a reliable criterion for determination of host suitability. Because of the better rooting results with IBA treatment, 105-day-old cuttings were first rooted with IBA in perlite and then transferred into sand for nematode inoculation. Known highly resistant genotypes of Myrobalan plum were gall-free and the responses of other genotypes paralleled that of the reference hardwood cuttings, although the test was less discriminating. Expression of M. arenaria host suitability in Myrobalan plum depends on root tissue maturation and cannot be reliably evaluated with 50-day-old cuttings. PMID:19277333

  5. Finite element simulation of conventional and prestressed cutting of Ti6Al4V

    NASA Astrophysics Data System (ADS)

    Peng, Ruitao; Tang, Xinzi; Tan, Yuanqiang; Liu, Xiongwei

    2013-05-01

    Titanium alloys are known as difficult-to-machine materials, chip morphology plays a predominant role in determining machinability and tool wear during the machining of titanium alloys. Based on the finite element analysis and experimental validation, the cutting processes in conventional cutting and prestressed cutting of titanium alloy ring parts were explored respectively. The Johnson-Cook model expressed by equivalent plastic strain flow stress is utilized to describe the constitutive properties. A ductile fracture criterion based on the strain energy is applied to model the crack initiation and evolution during the chip segmentation. Cutting force as well as distributions of stress, temperature and equivalent plastic strain along cutting time were numerically compared. The results indicate that in conventional cutting and prestressed cutting, chips show the similar characteristic of continuous and regular serrated shape. Initial stress distribution of workpiece was changed by prestress, which correspondingly leads to the alteration of stress distribution in the subsurface layer. Prestress hardly influences the distributions of temperature and equivalent plastic strain on workpiece. The cutting force curves share the same average amplitude and analogous undulating rhythm.

  6. The human cut homeodomain protein represses transcription from the c-myc promoter.

    PubMed Central

    Dufort, D; Nepveu, A

    1994-01-01

    Studies of the c-myc promoter have shown that efficient transcription initiation at the P2 start site as well as the block to elongation of transcription require the presence of the ME1a1 protein binding site upstream of the P2 TATA box. Following fractionation by size exclusion chromatography, three protein-ME1a1 DNA complexes, a, b, and c, were detected by electrophoretic mobility shift assay. A cDNA encoding a protein present in complex c was isolated by screening of an expression library with an ME1a1 DNA probe. This cDNA was found to encode the human homolog of the Drosophila Cut homeodomain protein. The bacterially expressed human Cut (hu-Cut) protein bound to the ME1a1 site, and antibodies against hu-Cut inhibited the ME1a1 binding activity c in nuclear extracts. In cotransfection experiments, the hu-Cut protein repressed transcription from the c-myc promoter, and this repression was shown to be dependent on the presence of the ME1a1 site. Using a reporter construct with a heterologous promoter, we found that c-myc exon 1 sequences were also necessary, in addition to the ME1a1 site, for repression by Cut. Taken together, these results suggest that the human homolog of the Drosophila Cut homeodomain protein is involved in regulation of the c-myc gene. Images PMID:8196661

  7. A novel protein elicitor (SsCut) from Sclerotinia sclerotiorum induces multiple defense responses in plants.

    PubMed

    Zhang, Huajian; Wu, Qun; Cao, Shun; Zhao, Tongyao; Chen, Ling; Zhuang, Peitong; Zhou, Xiuhong; Gao, Zhimou

    2014-11-01

    In this study, we report the cloning of the SsCut gene encoding cutinase from Sclerotinia sclerotiorum. We isolated a 609-bp cDNA encoding a polypeptide of 202 amino acids with a molecular weight of 20.4 kDa. Heterologous expression of SsCut in Escherichia coli (His-SsCut) caused the formation of lesions in tobacco that closely resembled hypersensitive response lesions. Mutational analysis identified the C-terminal-half peptide and the same amino acids indispensable for both enzyme and elicitor activity. His-SsCut was caused cell death in Arabidopsis, soybean (Glycine max), oilseed rape (Brassica napus), rice (Oryza sativa), maize (Zea mays), and wheat (Triticum aestivum), indicating that both dicot and monocot species are responsive to the elicitor. Furthermore, the elicitation of tobacco was effective in the induction of the activities of hydrogen peroxide, phenylalanine ammonia-lyase, peroxides, and polyphenol oxidase. His-SsCut-treated plants exhibited enhanced resistance as indicated by a significant reduction in the number and size of S. sclerotiorum, Phytophthora sojae, and P. nicotianae lesions on leaves relative to controls. Real-time PCR results indicated that the expression of defense-related genes and genes involved in signal transduction were induced by His-SsCut. Our results demonstrate that SsCut is an elicitor that triggers defense responses in plants and will help to clarify its relationship to downstream signaling pathways that induce defense responses.

  8. The Ecdysone and Notch Pathways Synergistically Regulate Cut at the Dorsal-Ventral Boundary in Drosophila Wing Discs

    PubMed Central

    Jia, Dongyu; Bryant, Jamal; Jevitt, Allison; Calvin, Gabriel; Deng, Wu-Min

    2017-01-01

    Metazoan development requires coordination of signaling pathways to regulate patterns of gene expression. In Drosophila, the wing imaginal disc provides an excellent model for the study of how signaling pathways interact to regulate pattern formation. The determination of the dorsal/ventral (DV) boundary of the wing disc depends on the Notch pathway, which is activated along the DV boundary and induces the expression of the homeobox transcription factor, Cut. Here, we show that Broad (Br), a zinc-finger transcription factor, is also involved in regulating Cut expression in the DV boundary region. However, Br expression is not regulated by Notch signaling in wing discs, rather, ecdysone signaling is the upstream signal that induces Br for Cut upregulation. Also, we find that the ecdysone-Br cascade upregulates cut-lacZ expression, a reporter containing a 2.7 kb cut enhancer region, implying that ecdysone signaling, similar to Notch, regulates cut at the transcriptional level. Collectively, our findings reveal that the Notch and ecdysone signaling pathways synergistically regulate Cut expression for proper DV boundary formation in the wing disc. Additionally, we show br promotes Delta, a Notch ligand, near the DV boundary to suppress aberrant high Notch activity, indicating further interaction between the two pathways for DV patterning of the wing disc. PMID:27117286

  9. Simplified cut core inductor design

    NASA Technical Reports Server (NTRS)

    Mclyman, W. T.

    1974-01-01

    Although filter inductor designers have routinely tended to specify molypermalloy powder cores for use in high frequency power converters and pulse-width modulated switching regulators, there are sigificant advantages in specifying C cores and cut toroids fabricated from grain oriented silicon steels which should not be overlooked. Such steel cores can develop flux densities of 1.6 tesla, with useful linearity to 1.2 tesla, whereas molypermalloy cores carrying d.c. current have useful flux density capabilities only to about 0.3 tesla. The use of silicon steel cores thus makes it possible to design more compact cores, and therefore inductors of reduced volume, or conversely to provide greater load capacity in inductors of a given volume. Information is available which makes it possible to obtain quick and close approximations of significant parameters such as size, weight and temperature rise for silicon steel cores for breadboarding. Graphs, nomographs and tables are presented for this purpose, but more complete mathematical derivations of some of the important parameters are also included for a more rigorous treatment.

  10. SLSL Ribbon-cutting Ceremony

    NASA Image and Video Library

    2003-11-19

    Representatives of the NASA-Kennedy Space Center and the state of Florida prepare to cut the ribbon officially opening the Space Life Sciences Lab at a ceremony at the new lab. In the front row, from left, are Dr. Samuel Durrance, executive director of the Florida Space Research Institute; Jim Kennedy, director of the Kennedy Space Center; Frank T. Brogan, president of the Florida Atlantic University; The Honorable Toni Jennings, lieutenant governor of the state of Florida; and Catherine and Grier Kirkpatrick, children of the late Sen. George Kirkpatrick. In the back row, from left, are Debra Holliday, director for Facilities and Construction, Florida Space Authority; Dan LeBlanc, president and chief operating officer of Delaware North Companies Parks and Resorts at KSC, Inc.; Jose Perez-Morales, NASA Project Manager for the Space Life Sciences Lab; and Capt. Winston E. Scott, executive director of the Florida Space Authority. Completed in August, the facility encompasses more than 100,000 square feet and was formerly known as the Space Experiment Research and Processing Laboratory or SERPL. The state, through the Florida Space Authority, built the research lab which is host to NASA, NASA’s Life Sciences Services contractor Dynamac Corp., Bionetics Corp., and researchers from the University of Florida. Dynamac Corp. leases the facility. The Florida Space Research Institute is responsible for gaining additional tenants from outside the NASA community.

  11. Corner-cutting mining assembly

    DOEpatents

    Bradley, J.A.

    1981-07-01

    This invention resulted from a contract with the United States Department of Energy and relates to a mining tool. More particularly, the invention relates to an assembly capable of drilling a hole having a square cross-sectional shape with radiused corners. In mining operations in which conventional auger-type drills are used to form a series of parallel, cylindrical holes in a coal seam, a large amount of coal remains in place in the seam because the shape of the holes leaves thick webs between the holes. A higher percentage of coal can be mined from a seam by a means capable of drilling holes having a substantially square cross section. It is an object of this invention to provide an improved mining apparatus by means of which the amount of coal recovered from a seam deposit can be increased. Another object of the invention is to provide a drilling assembly which cuts corners in a hole having a circular cross section. These objects and other advantages are attained by a preferred embodiment of the invention.

  12. Cutting fluid for machining fissionable materials

    SciTech Connect

    Duerksen, W.K.; Googin, J.M.; Napier, B. Jr.

    1982-01-28

    The present invention is directed to a cutting fluid for machining fissionable material. The cutting fluid is formed of glycol, water and a boron compound in an adequate concentration for effective neutron attenuation so as to inhibit criticality incidents during machining.

  13. Cut Next Winter's Heating Bill Today.

    ERIC Educational Resources Information Center

    Sturgeon, Julie

    1999-01-01

    Presents specific steps that help make schools energy efficient and cut costs. Four basic strategies are suggested that include creating a database of energy usage that can also catch the occasional billing error, investigating less obvious ways of cutting energy use, such as applying cellulose commercial spray as an insulation choice, and…

  14. Cut Next Winter's Heating Bill Today.

    ERIC Educational Resources Information Center

    Sturgeon, Julie

    1999-01-01

    Presents specific steps that help make schools energy efficient and cut costs. Four basic strategies are suggested that include creating a database of energy usage that can also catch the occasional billing error, investigating less obvious ways of cutting energy use, such as applying cellulose commercial spray as an insulation choice, and…

  15. Microwave interferometer controls cutting depth of plastics

    NASA Technical Reports Server (NTRS)

    Heisman, R. M.; Iceland, W. F.

    1969-01-01

    Microwave interferometer system controls the cutting of plastic materials to a prescribed depth. The interferometer is mounted on a carriage with a spindle and cutting tool. A cross slide, mounted on the carriage, allows the interferometer and cutter to move toward or away from the plastic workpiece.

  16. Cutting Watermelon: Lessons in Instructional Coaching

    ERIC Educational Resources Information Center

    Sandstead, Martha

    2016-01-01

    Literacy coordinator Martha Sandstead finds inspiration for her coaching work in a quote from civil rights organizer Lawrence Guyot: "Let's say you're riding past a picnic, and people are cuttin' watermelons. You don't immediately go and say, "stop the watermelon cutting" and let's talk. … You cut some watermelons, or you help…

  17. Cutting Watermelon: Lessons in Instructional Coaching

    ERIC Educational Resources Information Center

    Sandstead, Martha

    2016-01-01

    Literacy coordinator Martha Sandstead finds inspiration for her coaching work in a quote from civil rights organizer Lawrence Guyot: "Let's say you're riding past a picnic, and people are cuttin' watermelons. You don't immediately go and say, "stop the watermelon cutting" and let's talk. … You cut some watermelons, or you help…

  18. Scissors: More than a Cut Above

    ERIC Educational Resources Information Center

    Suzanne, Teri

    2005-01-01

    Scissors are a unique interactive tool when successfully used, allowing teachers and students to recognize and explore each other's creative ability while nurturing mutual communication. Freehand cutting gives children freedom to create as they cut. Scissors have the power to improve fine motor skills, stimulate creative imagination, reinforce…

  19. 33 CFR 117.143 - Bishop Cut.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 33 Navigation and Navigable Waters 1 2013-07-01 2013-07-01 false Bishop Cut. 117.143 Section 117.143 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY BRIDGES DRAWBRIDGE OPERATION REGULATIONS Specific Requirements California § 117.143 Bishop Cut. The draw of the San Joaquin...

  20. 33 CFR 117.161 - Honker Cut.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 33 Navigation and Navigable Waters 1 2013-07-01 2013-07-01 false Honker Cut. 117.161 Section 117.161 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY BRIDGES DRAWBRIDGE OPERATION REGULATIONS Specific Requirements California § 117.161 Honker Cut. The draw of the San Joaquin...

  1. 33 CFR 117.143 - Bishop Cut.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 33 Navigation and Navigable Waters 1 2010-07-01 2010-07-01 false Bishop Cut. 117.143 Section 117.143 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY BRIDGES DRAWBRIDGE OPERATION REGULATIONS Specific Requirements California § 117.143 Bishop Cut. The draw of the San Joaquin...

  2. 33 CFR 117.161 - Honker Cut.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 33 Navigation and Navigable Waters 1 2010-07-01 2010-07-01 false Honker Cut. 117.161 Section 117.161 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY BRIDGES DRAWBRIDGE OPERATION REGULATIONS Specific Requirements California § 117.161 Honker Cut. The draw of the San Joaquin...

  3. CUTTING PLANE METHODS WITHOUT NESTED CONSTRAINT SETS

    DTIC Science & Technology

    General conditions are given for the convergence of a class of cutting -plane algorithms without requiring that the constraint sets for the... cutting -planes include that of Kelley and a generalization of that used by Zoutendisk and Veinott. For algorithms with nested constraint sets, these

  4. 33 CFR 117.143 - Bishop Cut.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 33 Navigation and Navigable Waters 1 2014-07-01 2014-07-01 false Bishop Cut. 117.143 Section 117.143 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY BRIDGES DRAWBRIDGE OPERATION REGULATIONS Specific Requirements California § 117.143 Bishop Cut. The draw of the San Joaquin...

  5. Millimeter-Wave Cut-Off Switch.

    DTIC Science & Technology

    A millimeter-wave cut -off switch in a dielectric waveguide having a semi-insulating core and a semi-conducting epitaxial layer. A controller affixed...When the waveguide is properly dimensioned such that the operating frequency lies in the high-loss section near the cut -off frequency on the loss vs

  6. 33 CFR 117.143 - Bishop Cut.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 33 Navigation and Navigable Waters 1 2012-07-01 2012-07-01 false Bishop Cut. 117.143 Section 117.143 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY BRIDGES DRAWBRIDGE OPERATION REGULATIONS Specific Requirements California § 117.143 Bishop Cut. The draw of the San Joaquin...

  7. 33 CFR 117.161 - Honker Cut.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 33 Navigation and Navigable Waters 1 2012-07-01 2012-07-01 false Honker Cut. 117.161 Section 117.161 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY BRIDGES DRAWBRIDGE OPERATION REGULATIONS Specific Requirements California § 117.161 Honker Cut. The draw of the San Joaquin...

  8. 33 CFR 117.161 - Honker Cut.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 33 Navigation and Navigable Waters 1 2011-07-01 2011-07-01 false Honker Cut. 117.161 Section 117.161 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY BRIDGES DRAWBRIDGE OPERATION REGULATIONS Specific Requirements California § 117.161 Honker Cut. The draw of the San Joaquin...

  9. 33 CFR 117.161 - Honker Cut.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 33 Navigation and Navigable Waters 1 2014-07-01 2014-07-01 false Honker Cut. 117.161 Section 117.161 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY BRIDGES DRAWBRIDGE OPERATION REGULATIONS Specific Requirements California § 117.161 Honker Cut. The draw of the San Joaquin...

  10. 33 CFR 117.143 - Bishop Cut.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 33 Navigation and Navigable Waters 1 2011-07-01 2011-07-01 false Bishop Cut. 117.143 Section 117.143 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY BRIDGES DRAWBRIDGE OPERATION REGULATIONS Specific Requirements California § 117.143 Bishop Cut. The draw of the San Joaquin...

  11. Vegetative Propagation of Aspen by Greenwood Cuttings

    Treesearch

    Robert E. Farmer

    1963-01-01

    Greenwood stem cuttings taken from root suckers of Populus tremuloides and P. grandidentata were rooted in coarse sand under both intermittent mist and polyethylene sheeting in a greenhouse and under mist in an outdoor propagation bed. Prerooting treatment of cuttings with aqueous solutions of lBA (20-100 p.p.m. ) stimulated...

  12. Meat Cutting Classes--Popular with Adults

    ERIC Educational Resources Information Center

    Mostad, James; Carpentier, Dale

    1976-01-01

    Presents a session by session description of a "meats" class, which is offered to high school students (9-week period) and adults (8-week period). The classes cover identification of cuts (beef, sheep, hogs, and veal; grades and grading of live animals and carcasses; economics of butchering and cutting your own meat; actual slaughtering; and the…

  13. Surface sterilization of hybrid poplar cuttings

    Treesearch

    Alma M. Waterman

    1954-01-01

    Fungus diseases of hybrid poplars may be spread by spores that lodge in the resinous coating of buds of dormant cuttings, and in the lenticels. Surface sterilization by dipping the cuttings in fungicides was tested to determine whether such treatment would prevent the germination of spores of the canker-producing fungi Septoria musiva and Dothichiza populea and the...

  14. Scissors: More than a Cut Above

    ERIC Educational Resources Information Center

    Suzanne, Teri

    2005-01-01

    Scissors are a unique interactive tool when successfully used, allowing teachers and students to recognize and explore each other's creative ability while nurturing mutual communication. Freehand cutting gives children freedom to create as they cut. Scissors have the power to improve fine motor skills, stimulate creative imagination, reinforce…

  15. Postharvest: Cut flowers and potted plants

    USDA-ARS?s Scientific Manuscript database

    In the past fifty years, the cut flower market has changed dramatically, from a local market with growers located on city outskirts, to a global one; flowers and cut foliage sourced from throughout the world are sold as bunches or combined into arrangements and bouquets in the major target markets. ...

  16. Vee-notch tool cuts specimens

    NASA Technical Reports Server (NTRS)

    Spier, R. A.

    1970-01-01

    Triangular cutting tool uses carbide tips for notching heat-treated or abrasive materials, and alloys subjected to high structural stresses. The tool is rigidly mounted in a slot of mating contour to prevent deflection during cutting of tensile specimens. No other expensive machine equipment is required.

  17. Gluebond strength of laser cut wood

    Treesearch

    Charles W. McMillin; Henry A. Huber

    1985-01-01

    The degree of strength loss when gluing laser cut wood as compared to conventionally sawn wood and the amount of additional surface treatment needed to improve bond quality were assessed under normal furniture plant operating conditions. The strength of laser cut oak glued with polyvinyl acetate adhesive was reduced to 75 percent of sawn joints and gum was reduced 43...

  18. Meat Cutting Classes--Popular with Adults

    ERIC Educational Resources Information Center

    Mostad, James; Carpentier, Dale

    1976-01-01

    Presents a session by session description of a "meats" class, which is offered to high school students (9-week period) and adults (8-week period). The classes cover identification of cuts (beef, sheep, hogs, and veal; grades and grading of live animals and carcasses; economics of butchering and cutting your own meat; actual slaughtering; and the…

  19. College Students Tell Why They Cut Classes.

    ERIC Educational Resources Information Center

    Gladstone, Roy; Pope, Deborah Rose

    1979-01-01

    Students were asked to indicate why they cut class. While instructors came in for their share of the blame, the students attributed a large percentage of their cuts to causes for which the teachers were not at all responsible. Many of the most frequently given reasons suggest a simple carefree attitude on the part of the student. (Author)

  20. Drilling subsurface wellbores with cutting structures

    DOEpatents

    Mansure, Arthur James; Guimerans, Rosalvina Ramona

    2010-11-30

    A system for forming a wellbore includes a drill tubular. A drill bit is coupled to the drill tubular. One or more cutting structures are coupled to the drill tubular above the drill bit. The cutting structures remove at least a portion of formation that extends into the wellbore formed by the drill bit.

  1. Cutting tool form compensaton system and method

    DOEpatents

    Barkman, William E.; Babelay, Jr., Edwin F.; Klages, Edward J.

    1993-01-01

    A compensation system for a computer-controlled machining apparatus having a controller and including a cutting tool and a workpiece holder which are movable relative to one another along a preprogrammed path during a machining operation utilizes a camera and a vision computer for gathering information at a preselected stage of a machining operation relating to the actual shape and size of the cutting edge of the cutting tool and for altering the preprogrammed path in accordance with detected variations between the actual size and shape of the cutting edge and an assumed size and shape of the cutting edge. The camera obtains an image of the cutting tool against a background so that the cutting tool and background possess contrasting light intensities, and the vision computer utilizes the contrasting light intensities of the image to locate points therein which correspond to points along the actual cutting edge. Following a series of computations involving the determining of a tool center from the points identified along the tool edge, the results of the computations are fed to the controller where the preprogrammed path is altered as aforedescribed.

  2. Cutting tool form compensation system and method

    DOEpatents

    Barkman, W.E.; Babelay, E.F. Jr.; Klages, E.J.

    1993-10-19

    A compensation system for a computer-controlled machining apparatus having a controller and including a cutting tool and a workpiece holder which are movable relative to one another along a preprogrammed path during a machining operation utilizes a camera and a vision computer for gathering information at a preselected stage of a machining operation relating to the actual shape and size of the cutting edge of the cutting tool and for altering the preprogrammed path in accordance with detected variations between the actual size and shape of the cutting edge and an assumed size and shape of the cutting edge. The camera obtains an image of the cutting tool against a background so that the cutting tool and background possess contrasting light intensities, and the vision computer utilizes the contrasting light intensities of the image to locate points therein which correspond to points along the actual cutting edge. Following a series of computations involving the determining of a tool center from the points identified along the tool edge, the results of the computations are fed to the controller where the preprogrammed path is altered as aforedescribed. 9 figures.

  3. [Cutting and incision tools: the scalpel: handles].

    PubMed

    Illana Esteban, Emilio

    2006-10-01

    In its current version, a scalpel is the best known cutting tool. It comes with a versatile metallic handle, available in a variety of models having differentiated characteristics. With a few simple movements, all models enable you to articulate and extract multiple cutting blades.

  4. Application of high-rate cutting tools

    NASA Astrophysics Data System (ADS)

    Moriarty, John L., Jr.

    1989-03-01

    Widespread application of the newest high-rate cutting tools to the most appropriate jobs is slowed by the sheer magnitude of developments in tool types, materials, workpiece applications, and by the rapid pace of change. Therefore, a study of finishing and roughing sizes of coated carbide inserts having a variety of geometries for single point turning was completed. The cutting tools were tested for tool life, chip quality, and workpiece surface finish at various cutting conditions with medium alloy steel. An empirical wear-life data base was established, and a computer program was developed to facilitate technology transfer, assist selection of carbide insert grades, and provide machine operating parameters. A follow-on test program was implemented suitable for next generation coated carbides, rotary cutting tools, cutting fluids, and ceramic tool materials.

  5. Changing cultural attitudes towards female genital cutting.

    PubMed

    Vogt, Sonja; Mohmmed Zaid, Nadia Ahmed; El Fadil Ahmed, Hilal; Fehr, Ernst; Efferson, Charles

    2016-10-27

    As globalization brings people with incompatible attitudes into contact, cultural conflicts inevitably arise. Little is known about how to mitigate conflict and about how the conflicts that occur can shape the cultural evolution of the groups involved. Female genital cutting is a prominent example. Governments and international agencies have promoted the abandonment of cutting for decades, but the practice remains widespread with associated health risks for millions of girls and women. In their efforts to end cutting, international agents have often adopted the view that cutting is locally pervasive and entrenched. This implies the need to introduce values and expectations from outside the local culture. Members of the target society may view such interventions as unwelcome intrusions, and campaigns promoting abandonment have sometimes led to backlash as they struggle to reconcile cultural tolerance with the conviction that cutting violates universal human rights. Cutting, however, is not necessarily locally pervasive and entrenched. We designed experiments on cultural change that exploited the existence of conflicting attitudes within cutting societies. We produced four entertaining movies that served as experimental treatments in two experiments in Sudan, and we developed an implicit association test to unobtrusively measure attitudes about cutting. The movies depart from the view that cutting is locally pervasive by dramatizing members of an extended family as they confront each other with divergent views about whether the family should continue cutting. The movies significantly improved attitudes towards girls who remain uncut, with one in particular having a relatively persistent effect. These results show that using entertainment to dramatize locally discordant views can provide a basis for applied cultural evolution without accentuating intercultural divisions.

  6. Corn stalk orientation effect on mechanical cutting

    SciTech Connect

    Igathinathane, C.; Womac, A.R.; Sokhansanj, Shahabaddine

    2010-07-01

    Research efforts that increase the efficiency of size reduction of biomass can lead to a significant energy saving. This paper deals with the determination of the effect of sample orientation with respect to cutting element and quantify the possible cutting energy reduction, utilising dry corn stalks as the test material (15%e20% wet basis). To evaluate the mechanical cutting characteristics of corn stalks, a Warnere Bratzler device was modified by replacing its blunt edged cutting element with one having a 30_ single bevel sharp knife edge. Cutting force-deformation characteristics obtained with a universal testing machine were analysed to evaluate the orientation effects at perpendicular (90o), inclined (45o), and parallel (0o) orientations on internodes and nodes for cutting force, energy, ultimate stress, and specific energy of corn stalks. The corn stalks cutting force-displacement characteristics were found to differ with orientation, and internode and node material difference. Overall, the peak failure force, and the total cutting energy of internodes and nodes varied significantly (P < 0.05) with stalk cross-sectional area. The specific energy values (total energy per unit cut area) of dry corn stalk internodes ranged from 11.3 to 23.5 kN m_1, and nodes from 8.6 to 14.0 kN m_1. The parallel orientation (along grain) compared to perpendicular (across grain) produced a significant reduction of the cutting stress and the specific energy to one tenth or better for internodes, and to about one-fifth for nodes.

  7. Validity of the V-cut Test for Young Basketball Players.

    PubMed

    Gonzalo-Skok, O; Tous-Fajardo, J; Suarez-Arrones, L; Arjol-Serrano, J L; Casajús, J A; Mendez-Villanueva, A

    2015-11-01

    The aim of the present study was to assess the reliability, usefulness, validity, age-related differences and responsiveness of a 25- m side-step cutting maneuver test (V-cut test). Fifty young male basketball players performed the V-cut test on 2 occasions separated by 5-7 days to assess test-retest reliability and determine a priori usefulness. Twenty subjects also completed both the L-Run and 505 test to analyze the possible relationships among these 3 tests. Furthermore, 33 players performed the V-cut test 4 times throughout the season to analyze responsiveness. Finally, 53 players (U-14 to U-20) were assessed in the V-cut test to examine the age-related differences. Reliability scores showed high intraclass correlation coefficient (ICC=0.90) and low coefficient of variation (CV=1.4%). The responsiveness of the V-cut test was good, as the typical short- (1.5-1.7%), mid- (1.6-3.1%) and long-term (3.3%) changes in V-cut performance were higher than the CV. Low (r=0.64; CL90%: 0.34; 0.82) to moderate (r=0.76; CL90%: 0.53; 0.88) relationships were found between the V-cut test with the 505 and L-Run test, respectively. Age-related differences analysis showed better V-cut test performance as age increased in adolescent basketball players. The V-cut test is reliable to assess change of direction ability (CODA) and it could be used to monitor CODA in adolescent basketball players. © Georg Thieme Verlag KG Stuttgart · New York.

  8. Laser cutting of Kevlar laminates and thermal stress formed at cutting sections

    NASA Astrophysics Data System (ADS)

    Yilbas, B. S.; Akhtar, S. S.

    2012-02-01

    Laser cutting of Kevlar laminates is carried out and thermal stress field developed in the cutting region is predicted using the finite element code. Temperature predictions are validated through the thermocouple data. The morphological changes in the cutting section are examined by incorporating optical and scanning electron microscopes. It is found that temperature predictions agree well with the thermocouple data. High values of von Mises stress are observed at the cutting edges and at the mid-thickness of the Kevlar laminate due to thermal compression formed in this region. The laser cut edges are free from whiskers; however, striation formation and some small sideways burning is observed at the kerf edges.

  9. Portable propellant cutting assembly, and method of cutting propellant with assembly

    NASA Technical Reports Server (NTRS)

    Sharp, Roger A. (Inventor); Hoskins, Shawn W. (Inventor); Payne, Brett D. (Inventor)

    2002-01-01

    A propellant cutting assembly and method of using the assembly to cut samples of solid propellant in a repeatable and consistent manner is disclosed. The cutting assembly utilizes two parallel extension beams which are shorter than the diameter of a central bore of an annular solid propellant grain and can be loaded into the central bore. The assembly is equipped with retaining heads at its respective ends and an adjustment mechanism to position and wedge the assembly within the central bore. One end of the assembly is equipped with a cutting blade apparatus which can be extended beyond the end of the extension beams to cut into the solid propellant.

  10. Canada cuts export gas price to $4. 40; further cuts eyed

    SciTech Connect

    Slaff, J.

    1983-04-18

    Canada's plan to follow its April 54-cent cut in exported gas price for utilities with an additional cut to $3.30 per thousand cubic feet (mcf) will have the greatest impact on California and Pacific Northwest users. Northwest Pipeline, which currently imports 42% from Canada, assumes that the price cut is aimed at attracting a larger market share. Others question whether the second cut will occur because of internal political pressure between western energy developers who want higher prices and the Ottawa government. Both the US and Canadian governments see the first price cut as a token gesture since Canadian gas accounts for only 4% of the US market. (DCK)

  11. Final Report

    SciTech Connect

    Stinis, Panos

    2016-08-07

    This is the final report for the work conducted at the University of Minnesota (during the period 12/01/12-09/18/14) by PI Panos Stinis as part of the "Collaboratory on Mathematics for Mesoscopic Modeling of Materials" (CM4). CM4 is a multi-institution DOE-funded project whose aim is to conduct basic and applied research in the emerging field of mesoscopic modeling of materials.

  12. Final Report

    SciTech Connect

    Marchant, Gary E.

    2013-04-23

    This is the final report of a two year project entitled "Governing Nanotechnology Risks and Benefits in the Transition to Regulation: Innovative Public and Private Approaches." This project examined the role of new governance or "soft law" mechanisms such as codes of conduct, voluntary programs and partnership agreements to manage the risks of emerging technologies such as nanotechnology. A series of published or in publication papers and book chapters are attached.

  13. Final Report

    SciTech Connect

    R. Paul Drake

    2001-11-30

    This final report describes work involving 22 investigators from 11 institutions to explore the dynamics present in supernova explosions by means of experiments on the Omega laser. The specific experiments emphasized involved the unstable expansion of a spherical capsule and the coupling of perturbations at a first interface to a second interface by means of a strong shock. Both effects are present in supernovae. The experiments were performed at Omega and the computer simulations were undertaken at several institutions. B139

  14. Process monitoring during CO2 laser cutting

    NASA Astrophysics Data System (ADS)

    Jorgensen, Henning; Olsen, Flemming O.

    1991-05-01

    On-line process control equipment for CO2 laser cutting is not available for industrial applications today. The majority of the industrial cutting machines are regulated off-line by highly-educated staffs. The quality inspection of the samples often is visual, and referred to different quality scales. Due to this lack of automatization, potential laser users hesitate to implement the cutting method and hereby to benefit from the advantages offered by the method. The first step toward an automatization of the process is development of a process monitoring system, and the investigation described in this paper is concentrated in the area of on-line quality detection during CO2 laser cutting. The method is based on detection of the emitted light from the cut front by photo diodes. The detection is made co-axial with the laser beam to assure independence of the chosen processing direction. ZnSe mirrors have been placed in the beam path, reflecting the laser beam but transmitting the visible light emitted from the process. Cut series of 2, 6 and 8 mm mild steel have been performed. Fourier Analyses and statistical analyses of the signals have been undertaken, and from these analyses it is possible to estimate the surface roughness in the cut kerf, dross attachment at the backside of the work piece and the penetration of the laser beam.

  15. Using inpainting to construct accurate cut-sky CMB estimators

    NASA Astrophysics Data System (ADS)

    Gruetjen, H. F.; Fergusson, J. R.; Liguori, M.; Shellard, E. P. S.

    2017-02-01

    The direct evaluation of manifestly optimal, cut-sky cosmic microwave background (CMB) power spectrum and bispectrum estimators is numerically very costly, due to the presence of inverse-covariance filtering operations. This justifies the investigation of alternative approaches. In this work, we mostly focus on an inpainting algorithm that was introduced in recent CMB analyses to cure cut-sky suboptimalities of bispectrum estimators. First, we show that inpainting can equally be applied to the problem of unbiased estimation of power spectra. We then compare the performance of a novel inpainted CMB temperature power spectrum estimator to the popular apodized pseudo-Cl (PCL) method and demonstrate, both numerically and with analytic arguments, that inpainted power spectrum estimates significantly outperform PCL estimates. Finally, we study the case of cut-sky bispectrum estimators, comparing the performance of three different approaches: inpainting, apodization and a novel low-l leaning scheme. Providing an analytic argument of why the local shape is typically most affected we mainly focus on local-type non-Gaussianity. Our results show that inpainting allows us to achieve optimality also for bispectrum estimation, but interestingly also demonstrate that appropriate apodization, in conjunction with low-l cleaning, can lead to comparable accuracy.

  16. Braking characteristics during cutting and pivoting in female soccer players.

    PubMed

    Jones, Paul A; Herrington, Lee; Graham-Smith, Philip

    2016-10-01

    Most biomechanical studies into changing direction focus on final contact (FC), whilst limited research has examined penultimate contact (PEN). The aim of this study was to explore the kinematic and kinetic differences between PEN and FC of cutting and pivoting in 22 female soccer players (mean±SD; age: 21±3.1years, height: 1.68±0.07m, mass: 58.9±7.3kg). Furthermore, the study investigated whether horizontal force-time characteristics during PEN were related to peak knee abduction moments during FC. Three dimensional motion analyses of cutting and pivoting on the right leg were performed using Qualysis 'Proreflex' infrared cameras (240Hz). Ground reaction forces (GRF) were collected from two AMTI force platforms (1200Hz) to examine PEN and FC. Both manoeuvres involved significantly (P<0.05) greater knee joint flexion angles, peak horizontal GRF, but lower average horizontal GRF during PEN compared to FC. Average horizontal GRF during PEN (R=-0.569, R(2)=32%, P=0.006) and average horizontal GRF ratio (R=0.466, R(2)=22%, P=0.029) were significantly related to peak knee abduction moments during the FC of cutting and pivoting, respectively. The results indicate PEN during pre-planned changing direction helps reduce loading on the turning leg where there is greater risk of injuries to knee ligaments.

  17. Morphology and hydrodynamics of wave-cut gullies

    NASA Astrophysics Data System (ADS)

    Priestas, A. M.; Fagherazzi, S.

    2011-08-01

    Wave-cut gullies are sub-triangular incisions common along deteriorating marsh scarps. Wave gullies may be equispaced to quasi-equispaced and enlarge in time, incising the marsh boundary. A high resolution survey is provided for ten wave gullies formed along the chenier plain of the Rockefeller Wildlife Refuge, Louisiana, USA. The measurements capture the morphologic character, evolution, and erosion rates of wave-cut gullies over a two month period. The data relate changes in morphology to geometric factors and shoreline retreat. Finally, the first analysis of wave data measured by acoustic Doppler velocity profilers is presented to show how propagating waves are transformed inside a wave-cut gully in order to describe the processes leading to their formation. Results show that waves of intermediate period (4-6 s) yield very strong swash currents that hit the gully head, detaching marsh substrate and triggering headward erosion. A conceptual model of wave gully evolution is presented as an explanation for this non-uniform, episodic shoreline erosion.

  18. Analysis of multi-e-beam lithography for cutting layers at 7-nm node

    NASA Astrophysics Data System (ADS)

    Zhao, Lijun; Wei, Yayi; Ye, Tianchun

    2016-10-01

    Technology node scaling to the 7-nm node, self-aligned quadruple patterning plus cutting/blocking is widely adopted as a lithography solution for critical line and space layers. The cutting/blocking process can be done by 193i or EUV lithography. Due to resolution requirements in both X/Y directions, 193i requires two or three exposures to accomplish the cutting/blocking process, and the overlay among the exposures must be controlled very tightly. EUV can accomplish cutting/blocking by one exposure. However, the extremely high cost of EUV tool and mask, together with not so high throughput, appears to suggest that EUV lithography is not a cost-effective solution. From both technical and cost perspectives, we explore the possibility of using multi-e-beam lithography as an alternative solution for 7-nm cutting/blocking layers. First, we analyze design rules, which define resolution and overlay requirements of the cutting/blocking patterns. Then we report the lithography performance data of our leading-edge multi-e-beam tool and compare them with the cutting/blocking requirements. Finally, we do the cost analysis. Our results indicate that multi-e-beam lithography has a cost per wafer per layer advantage if it can commit a resolution of 32-nm half pitch, an overlay of <2.8 nm, and a throughput of 5 to 10 wph.

  19. Deferment cutting in Appalachian hardwoods: the what, whys, and hows

    Treesearch

    H. Clay Smith; Gary W. Miller

    1991-01-01

    Deferment cutting is a regeneration practice that resembles a seed-tree or shelterwood cutting. The difference is that residual trees are not cut when the reproduction becomes established. Instead, residual trees are left until new reproduction matures to sawtimber size, and another regeneration cut is the silvicultural objective. Hence, with deferment cutting specific...

  20. Laser Cutting of Carbon Fiber Reinforced Polymers using Highly Brilliant Laser Beam Sources

    NASA Astrophysics Data System (ADS)

    Klotzbach, Annett; Hauser, Markus; Beyer, Eckhard

    Carbon fiber reinforced polymers (CFRP) are applied more and more in the aircraft industry as well as in the automobile industry. The principal reason is the highly mechanical load capacity along with the low density. Moreover, the corrosion resistance plus the damping behavior of the material can be utilized fully in highly stressed structures. However, the concept of manufacture CFRP-parts close to the final contour does not substitute the need of cutting them. The different properties of fiberand matrix-material constitute an ambitious challenge while cutting CFRP using a laser beam. This paper deals with elementary analysis of the laser remote cutting process and the gas assisted laser cutting of CFRP.

  1. Making the cut: lattice kirigami rules.

    PubMed

    Castle, Toen; Cho, Yigil; Gong, Xingting; Jung, Euiyeon; Sussman, Daniel M; Yang, Shu; Kamien, Randall D

    2014-12-12

    In this Letter we explore and develop a simple set of rules that apply to cutting, pasting, and folding honeycomb lattices. We consider origami-like structures that are extrinsically flat away from zero-dimensional sources of Gaussian curvature and one-dimensional sources of mean curvature, and our cutting and pasting rules maintain the intrinsic bond lengths on both the lattice and its dual lattice. We find that a small set of rules is allowed providing a framework for exploring and building kirigami—folding, cutting, and pasting the edges of paper.

  2. Making the Cut: Lattice Kirigami Rules

    NASA Astrophysics Data System (ADS)

    Castle, Toen; Cho, Yigil; Gong, Xingting; Jung, Euiyeon; Sussman, Daniel M.; Yang, Shu; Kamien, Randall D.

    2014-12-01

    In this Letter we explore and develop a simple set of rules that apply to cutting, pasting, and folding honeycomb lattices. We consider origami-like structures that are extrinsically flat away from zero-dimensional sources of Gaussian curvature and one-dimensional sources of mean curvature, and our cutting and pasting rules maintain the intrinsic bond lengths on both the lattice and its dual lattice. We find that a small set of rules is allowed providing a framework for exploring and building kirigami—folding, cutting, and pasting the edges of paper.

  3. Imaging, cutting, and collecting instrument and method

    DOEpatents

    Tench, Robert J.; Siekhaus, Wigbert J.; Balooch, Mehdi; Balhorn, Rodney L.; Allen, Michael J.

    1995-01-01

    Instrumentation and techniques to image small objects, such as but not limited to individual human chromosomes, with nanometer resolution, to cut-off identified parts of such objects, to move around and manipulate such cut-off parts on the substrate on which they are being imaged to predetermined locations on the substrate, and to remove the cut-off parts from the substrate. This is accomplished using an atomic force microscope (AFM) and by modification of the conventional cantilever stylus assembly of an AFM, such that plural cantilevers are used with either sharp-tips or knife-edges thereon. In addition, the invention can be utilized for measuring hardness of materials.

  4. Laser cutting with chemical reaction assist

    SciTech Connect

    Gettemy, D.J.

    1991-04-08

    This invention is comprised of a method for cutting with a laser beam where an oxygen-hydrocarbon reaction is used to provide auxiliary energy to a metal workpiece to supplement the energy supplied by the laser. Oxygen is supplied to the laser focus point on the workpiece by a nozzle through which the laser beam also passes. A liquid hydrocarbon is supplied by coating the workpiece along the cutting path with the hydrocarbon prior to laser irradiation or by spraying a stream of hydrocarbon through a nozzle aimed at a point on the cutting path which is just ahead of the focus point during irradiation.

  5. Laser cutting with chemical reaction assist

    DOEpatents

    Gettemy, D.J.

    1992-11-17

    A method is described for cutting with a laser beam where an oxygen-hydrocarbon reaction is used to provide auxiliary energy to a metal workpiece to supplement the energy supplied by the laser. Oxygen is supplied to the laser focus point on the workpiece by a nozzle through which the laser beam also passes. A liquid hydrocarbon is supplied by coating the workpiece along the cutting path with the hydrocarbon prior to laser irradiation or by spraying a stream of hydrocarbon through a nozzle aimed at a point on the cutting path which is just ahead of the focus point during irradiation. 1 figure.

  6. Laser cutting with chemical reaction assist

    DOEpatents

    Gettemy, Donald J.

    1992-01-01

    A method for cutting with a laser beam where an oxygen-hydrocarbon reaction is used to provide auxiliary energy to a metal workpiece to supplement the energy supplied by the laser. Oxygen is supplied to the laser focus point on the workpiece by a nozzle through which the laser beam also passes. A liquid hydrocarbon is supplied by coating the workpiece along the cutting path with the hydrocarbon prior to laser irradiation or by spraying a stream of hydrocarbon through a nozzle aimed at a point on the cutting path which is just ahead of the focus point during irradiation.

  7. Reconfigurable manufacturing execution system for pipe cutting

    NASA Astrophysics Data System (ADS)

    Yin, Y. H.; Xie, J. Y.

    2011-08-01

    This article presents a reconfigurable manufacturing execution system (RMES) filling the gap between enterprise resource planning and resource layer for pipe-cutting production with mass customisation and rapid adaptation to dynamic market, which consists of planning and scheduling layer and executive control layer. Starting from customer's task and process requirements, the cutting trajectories are planned under generalised mathematical model able to reconfigure in accordance with various intersecting types' joint, and all tasks are scheduled by nesting algorithm to maximise the utilisation rate of rough material. This RMES for pipe cutting has been effectively implemented in more than 100 companies.

  8. Enhanced dental cutting through chemomechanical effects.

    PubMed

    von Fraunhofer, J A; Siegel, S C

    2000-10-01

    Previous studies have shown that certain surface-active agents--compounds that reduce interfacial tension--in a dental handpiece's irrigation water can enhance cutting rates, or CRs. This study evaluated these effects under test conditions simulating dental practice. The authors used a self-contained cutting system with a digitally controlled handpiece speed, torque and water flow rate to cut machinable glass ceramic (Macor, Corning Inc.) with medium-grit diamond burs and cross-cut fissure carbide burs under a load of 147.5 grams and 22 milliliters per minute coolant flow rate using water with mouthwash (Scope, Procter & Gamble) additions. They used six burs for each irrigant mixture to make three 5-millimeter edge cuts through 13 mm of Macor; CRs were quantified as the time necessary to transect the Macor cutting substrate. Additions of small amounts of mouthwash to the coolant water accelerated the CR for both carbide and diamond burs. The CRs for carbide burs in millimeters per second were distilled water, 0.21; 1:2.5 mouthwash:distilled water mixture, 0.12; 1:5 mixture, 0.64; and 1:10 mixture, 0.66. The CR differences for the 1:5 and 1:10 mixtures were significant (P < .001). The CRs for diamond burs in millimeters per second were distilled water, 0.09; 1:1 mouthwash:distilled water mixture, 0.13; 1:2.5 mixture, 0.16; 1:5 mixture, 0.21; and 1:10 mixture, 0.18. When it came to the diamond burs, the CR differences between water and the mouthwash:distilled water mixtures were significant (P < .001). The authors found that the mouthwash additions ensured higher CRs compared with those for water alone over the entire cutting regimen; that is, while the CRs for both carbide and diamond burs dropped with prolonged cutting with water irrigation, the addition of mouthwash resulted in the burs' cutting faster and for longer than with water alone. Adding small amounts of mouthwash to the coolant water significantly enhanced cutting by diamond and carbide burs and

  9. Final Report

    SciTech Connect

    Balmain, Allan

    2007-03-28

    The specific aims of this project were as follows: Aim 1: Identify mouse genetic loci that affect the survival time of mice post radiation Aim 2: Identify somatic genetic alterations that are indicative of tumor suppressor and oncogene loci involved in radiation-induced cancers. Aim 3: Identify candidate radiation susceptibility genes by gene expression microarray analysis of the radiation response in normal tissues or in tumors from the strains used for aims 1 and 2.

  10. Final Report

    SciTech Connect

    R Paul Drake

    2004-01-12

    OAK-B135 This is the final report from the project Hydrodynamics by High-Energy-Density Plasma Flow and Hydrodynamics and Radiation Hydrodynamics with Astrophysical Applications. This project supported a group at the University of Michigan in the invention, design, performance, and analysis of experiments using high-energy-density research facilities. The experiments explored compressible nonlinear hydrodynamics, in particular at decelerating interfaces, and the radiation hydrodynamics of strong shock waves. It has application to supernovae, astrophysical jets, shock-cloud interactions, and radiative shock waves.

  11. Auditing to the cutting edge

    SciTech Connect

    Good, L.; Wirdzek, P.

    1999-07-01

    Equipment? System? Building? Campus? Neighborhood? Community? Region? What is to be audited and what needs to be corrected? Can the energy management professional decide, or should the customer? Over the last few decades, energy professionals have been evaluating energy use in order to balance clients' expenditures with acceptable levels of service. Traditionally, professional expertise and creativity have been limited more by budget than any other single element. Today, energy and the environment are tightly intertwined. In the future, effective energy management may not be possible without considering the relationships between them. Conversely, environmental protection cannot be achieved without considering energy production, distribution, and use. To this end, two powerful federal organizations, the US Environmental Protection Agency (EPA) and the US Department of Energy (DOE), have been engaged in defining the interrelationships of these areas and fashioning national energy policies aimed at awakening Americans to these facts. Environmental demands are becoming a factor in efficiency equations. Energy management professionals should prepare a response. They will face demands for cutting-edge audits that reach further than giving utility power just a trim in the energy barber shop. Survival in the business of energy management will require a broader perspective. One need only look to current advertisements by national and international corporations which praise the environmental benefits of their products and even their places of business as cleaner than their competitors'. For the energy management professional then, energy diversity and source versus site considerations are opportunities to be identified in the audit process, in addition to replacement of inefficient equipment. The country is rich with technology choices, with documented experience, and with the knowledge to create systems that can mine deep savings. True, some have niche applications, which

  12. Final report

    SciTech Connect

    Susan S. Golden

    2005-03-31

    The originally funded project was geared to pursue research on regulation of photosystem II (PSII) in the cyanobacterium Synechococcus elongatus PCC 7942. We characterized a locus, psfR, (psbA stimulating factor) that affects expression of the psbAI gene, which encodes the PSII protein D1. Over-expression of psfR, which encodes a protein with receiver and pseudo-receiver domains, acts at the promoter region to elevate expression of psbAI and a subset of other loci. We reoriented the remainder of the funding to make a greater impact through completion of a functional genomics project that had been initiated with funding from another agency. The goal is inactivation of each gene individually in the S. elongatus genome, and completion of the entire genome sequence. At the end of the project we will have screened all loci for involvement in circadian rhythms of gene expression and assembled an archived set of clones that can be used to create the mutations to screen for any other phenotype. During the project period we: (1) prepared a functional genomics website for S. elongatus PCC 7942 that posts sequences prior to GenBank release, and presents the strategy and progress for the genomics project (http://www.bio.tamu.edu/synecho/); (2) determined the sequence of and annotated the S. elongatus 46 kb plasmid, pANL; (3) submitted assembled sequences with annotation of 8 cosmid inserts to GenBank (313 kb), with sites of transposon insertions indicated; (4) mutagenized approximately an additional 600 kb of the genome (16 cosmids) and identified sequences flanking the mutations; (5) recombined mutagenesis substrates into the S. elongatus genome to produce gene inactivations (at the sites of transposon insertions) for approximately 415 kb of mutagenized sequence (85% of these have already been screened for circadian phenotypes) (6) identified the clpPIIclpX locus as important in determining circadian period; and (7) demonstrated effectiveness of antisense RNA for decreasing

  13. Definition of fine cutting features for laser fusion cutting of stainless steel

    NASA Astrophysics Data System (ADS)

    Seebach, J.; Norman, S.; Harrison, P.

    2015-07-01

    Laser fusion cutting of stainless steel is often considered in a material range from 0,3mm up to 4mm and laser powers up to 2kW. For a given material thickness, different optimum beam and process parameters can be determined empirically, leading to a dross-free cut for high tool travel speeds. Realising sharp 90-degree corners, dross formation is observed and leads to a deteriorated cutting quality. With reorientation at small radii, the speed-dependent change in the cutting process is superimposed by the existing beam to nozzle misalignment and contributes to the stability of a cut. The feature radius R on the stability of the cutting process is being determined by reducing feature radius R. In this paper, cutting of different radii for different sized conventional nozzles is considered and analysed. Based on cutting quality evaluation, fine feature cutting is defined by discussing thickness-dependent finest cutting feature for a given gas dynamic input.

  14. An FMS Dynamic Production Scheduling Algorithm Considering Cutting Tool Failure and Cutting Tool Life

    NASA Astrophysics Data System (ADS)

    Setiawan, A.; Wangsaputra, R.; Martawirya, Y. Y.; Halim, A. H.

    2016-02-01

    This paper deals with Flexible Manufacturing System (FMS) production rescheduling due to unavailability of cutting tools caused either of cutting tool failure or life time limit. The FMS consists of parallel identical machines integrated with an automatic material handling system and it runs fully automatically. Each machine has a same cutting tool configuration that consists of different geometrical cutting tool types on each tool magazine. The job usually takes two stages. Each stage has sequential operations allocated to machines considering the cutting tool life. In the real situation, the cutting tool can fail before the cutting tool life is reached. The objective in this paper is to develop a dynamic scheduling algorithm when a cutting tool is broken during unmanned and a rescheduling needed. The algorithm consists of four steps. The first step is generating initial schedule, the second step is determination the cutting tool failure time, the third step is determination of system status at cutting tool failure time and the fourth step is the rescheduling for unfinished jobs. The approaches to solve the problem are complete-reactive scheduling and robust-proactive scheduling. The new schedules result differences starting time and completion time of each operations from the initial schedule.

  15. Laser Cutting of Leather: Tool for Industry or Designers?

    NASA Astrophysics Data System (ADS)

    Stepanov, Alexander; Manninen, Matti; Pärnänen, Inni; Hirvimäki, Marika; Salminen, Antti

    Currently technologies which are applied for leather cutting include slitting knifes, die press techniques and manual cutting. Use of laser technology has grown significantly during recent years due to number of advantages over conventional cutting methods; flexibility, high production speed, possibility to cut complex geometries, easier cutting of customized parts, and less leftovers of leather makes laser cutting more and more economically attractive to apply for leather cutting. Laser technology provides advantages in cutting complex geometries, stable cutting quality and possibility to utilize leather material in economically best way. Constant quality is important in industrial processes and laser technology fulfills this requirement: properly chosen laser cutting parameters provides identical cuts. Additionally, laser technology is very flexible in terms of geometries: complex geometries, individual designs, prototypes and small scale products can be manufactured by laser cutting. Variety of products, which needed to be cut in small volumes, is also the application where laser cutting can be more beneficial due to possibility to change production from one product to another only by changing geometry without a need to change cutting tool. Disadvantages of laser processing include high initial investment costs and some running costs due to maintenance and required gas supply for the laser. Higher level of operator's expertise is required due to more complicated machinery in case of laser cutting. This study investigates advantages and disadvantages of laser cutting in different areas of application and provides comparison between laser cutting and mechanical cutting of leather.

  16. Drug companies cut HIV drug prices in the developing world.

    PubMed

    Yamey, G

    2000-05-20

    The UN has reported that five multinational pharmaceutical companies would cut down HIV drug prices in the developing world. One of these drug companies is GlaxoWellcome, which has promised to reduce the price of zidovudine and lamivudine to US$2 in the poorest nations, a fifth of its price in the US. Although Peter Piot, director of the UN Program on HIV/AIDS, welcomed the companies' promises, he warned that price cuts alone will not curb the epidemic. He stated that this initiative is only one critical factor in what must become a much broader and more urgent effort to help people living with HIV/AIDS. Moreover, health and development agencies expressed concern that AIDS drugs will still be unaffordable for the vast majority of those in need in developing countries. In addition, poor countries lack the infrastructure to deliver these drugs safely and effectively. During the time of the UN announcement, US President Bill Clinton also signed an executive order allowing sub-Saharan Africa to adopt legal measures to obtain cheap HIV drugs. Meanwhile, South Africa's reaction to the offer to cut antiretroviral drug prices has been lukewarm.

  17. Making the Cut: Lattice Kirigami Rules

    NASA Astrophysics Data System (ADS)

    Castle, Toen; Cho, Yigil; Gong, Xingting; Jung, Euiyeon; Sussman, Daniel; Yang, Shu; Kamien, Randall

    2015-03-01

    Complex 3D structures can be built by bending and folding a flat sheet, as is done in origami. This paradigm can be extended by cutting and gluing the sheet as well as folding. The principles manifest in manipulating a piece of paper can translate across many length scales, limited only by fabrication methods. We explore and develop a simple set of rules that apply to cutting, pasting, and folding honeycomb lattices. We consider origami-like structures that are extrinsically flat away from zero-dimensional sources of Gaussian curvature and one-dimensional sources of mean curvature, and our cutting and pasting rules maintain the intrinsic bond lengths on both the lattice and its dual lattice. We find that a small set of rules is allowed, providing a framework for exploring and building kirigami - folding, cutting, and pasting the edges of paper. Support from NSF DMR12-62047.

  18. Checking Out Cuts, Scratches, and Abrasions

    MedlinePlus

    ... to get rid of the infection. Luckily, most cuts, scratches, and abrasions will go away on their own, thanks to your body's amazing ability to heal ... Story on Scars Cellulitis Taking Care of Your Skin What's a Scab? ...

  19. Chevron cutting: Experiment with new runway mixtures

    NASA Technical Reports Server (NTRS)

    Tyran, K. (Compiler)

    1978-01-01

    Chevron cutting is shown to occur in different forms depending on the type of tire and the rubber on the running surface. Hardest wear is shown by the main tires of the B-747. Four defects occurred, in the form of two rip separation and two breakouts of the running surface. Tires capped by Thompson are more affected than any of the other rubber-capping fabrics. For Thompson tires, Chevron Cutting is greatly reduced with a fiberglass-rubber mixture. For Goodyear tires, it is eliminated with spiral wrap rubbercapping; resistance to damages through cuts seems to be more positive for Goodyear tires. For Mader tires, the extent of Chevron Cutting is generally smaller than for Thompson cappings.

  20. 8 ways to cut health care costs

    MedlinePlus

    ... patientinstructions/000870.htm Eight ways to cut your health care costs To use the sharing features on this page, please enable JavaScript. The cost of health care continues to rise. That is why it helps ...

  1. School Custodial Costs Can Be Cut

    ERIC Educational Resources Information Center

    Forrest, W. F.

    1973-01-01

    A detailed examination of work methods, procedures, and equipment, followed by preparation of written schedules for each custodian, can cut custodial costs without affecting the quality of cleanliness in the schools. (Author/MLF)

  2. Rotavirus Vaccine Cut Kids' Hospitalization, Medical Costs

    MedlinePlus

    ... fullstory_167720.html Rotavirus Vaccine Cut Kids' Hospitalization, Medical Costs Virus a common cause of diarrhea among ... a savings of more than $1 billion in medical costs, the researchers added. Rotavirus is a common ...

  3. Cancer centers prepare for sequestration cuts.

    PubMed

    Bender, Eric

    2013-04-01

    With automatic U.S. federal budget cuts kicking in, cancer centers are readying for a significant downturn in spending, especially because the cost savings must be achieved in the remaining half of the federal fiscal year.

  4. Shingles Vaccine Cuts Chronic Pain, Hospitalizations

    MedlinePlus

    ... https://medlineplus.gov/news/fullstory_164156.html Shingles Vaccine Cuts Chronic Pain, Hospitalizations Protection lasts years after ... age, researchers said. The new study showed the vaccine was 74 percent effective in preventing hospitalizations for ...

  5. Freon, T-B1 cutting fluid

    NASA Technical Reports Server (NTRS)

    Peters, R. L.

    1969-01-01

    Improved cutting fluid completely controls the heat generated from machining operations, thus providing longer tool life. Fluid is especially useful in the working of plastics and replaces less efficient contaminating oils.

  6. Hydro Impact Basin Ribbon-Cutting Ceremony

    NASA Image and Video Library

    August 9, 2011 -- Ribbon-cutting ceremony for the Hydro Impact Basin at NASA's Langley Research Center in Hampton, Va. The HIB expands NASA's capability to test and certify future spacecraft for wa...

  7. Ribbon cutting opens new ELV offices

    NASA Technical Reports Server (NTRS)

    2000-01-01

    Center Director Roy Bridges welcomes the audience to a ribbon- cutting ceremony at the E&O Building at KSC. Home for NASA's unmanned missions since 1964, the building has been renovated to house the Expendable Launch Vehicle Program.

  8. Ribbon cutting opens new ELV offices

    NASA Technical Reports Server (NTRS)

    2000-01-01

    Center Director Roy Bridges welcomes the audience to a ribbon- cutting ceremony at the E&O Building at KSC. Home for NASA's unmanned missions since 1964, the building has been renovated to house the Expendable Launch Vehicle Program.

  9. Climate science hit by job cuts

    NASA Astrophysics Data System (ADS)

    Randall, Ian

    2016-03-01

    Climate researchers in Australia are bracing themselves for heavy job cuts as the country's national scientific agency - the Commonwealth Scientific and Industrial Research Organisation (CSIRO) - said last month it will reprioritize towards innovation.

  10. Cut Bank Municipal Airport and Army Air Force Base, Terminal ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    Cut Bank Municipal Airport and Army Air Force Base, Terminal Building, Approximately 390 yards west of Valier Highway (Montana Route 358), three miles southwest of Cut Bank, Cut Bank, Glacier County, MT

  11. The fission yeast SPB component Cut12 links bipolar spindle formation to mitotic control

    PubMed Central

    Bridge, Alan J.; Morphew, Mary; Bartlett, Rachel; Hagan, Iain M.

    1998-01-01

    During fission yeast mitosis, the duplicated spindle pole bodies (SPBs) nucleate microtubule arrays that interdigitate to form the mitotic spindle. cut12.1 mutants form a monopolar mitotic spindle, chromosome segregation fails, and the mutant undergoes a lethal cytokinesis. The cut12+ gene encodes a novel 62-kD protein with two predicted coiled coil regions, and one consensus phosphorylation site for p34cdc2 and two for MAP kinase. Cut12 is localized to the SPB throughout the cell cycle, predominantly around the inner face of the interphase SPB, adjacent to the nucleus. cut12+ is allelic to stf1+; stf1.1 is a gain-of-function mutation bypassing the requirement for the Cdc25 tyrosine phosphatase, which normally dephosphorylates and activates the p34cdc2/cyclin B kinase to promote the onset of mitosis. Expressing a cut12+ cDNA carrying the stf1.1 mutation also suppressed cdc25.22. The spindle defect in cut12.1 is exacerbated by the cdc25.22 mutation, and stf1.1 cells formed defective spindles in a cdc25.22 background at high temperatures. We propose that Cut12 may be a regulator or substrate of the p34cdc2 mitotic kinase. PMID:9531532

  12. Rock Cutting Depth Model Based on Kinetic Energy of Abrasive Waterjet

    NASA Astrophysics Data System (ADS)

    Oh, Tae-Min; Cho, Gye-Chun

    2016-03-01

    Abrasive waterjets are widely used in the fields of civil and mechanical engineering for cutting a great variety of hard materials including rocks, metals, and other materials. Cutting depth is an important index to estimate operating time and cost, but it is very difficult to predict because there are a number of influential variables (e.g., energy, geometry, material, and nozzle system parameters). In this study, the cutting depth is correlated to the maximum kinetic energy expressed in terms of energy (i.e., water pressure, water flow rate, abrasive feed rate, and traverse speed), geometry (i.e., standoff distance), material (i.e., α and β), and nozzle system parameters (i.e., nozzle size, shape, and jet diffusion level). The maximum kinetic energy cutting depth model is verified with experimental test data that are obtained using one type of hard granite specimen for various parameters. The results show a unique curve for a specific rock type in a power function between cutting depth and maximum kinetic energy. The cutting depth model developed here can be very useful for estimating the process time when cutting rock using an abrasive waterjet.

  13. Final report: FASEB Summer Research Conference on ''Post-transcriptional control of gene expression: Effectors of mRNA decay'' [agenda and attendees list

    SciTech Connect

    Maquat, Lynne

    2002-12-01

    The goal of this meeting was to provide an interactive forum for scientists working on prokaryotic and eukaryotic mRNA decay. A special seminar presented by a leader in the field of mRNA decay in S. cerevisiae focused on what is known and what needs to be determined, not only for yeast but for other organisms. The large attendance (110 participants) reflects the awareness that mRNA decay is a key player in gene regulation in a way that is affected by the many steps that precede mRNA formation. Sessions were held on the following topics: mRNA transport and mRNP; multicomponent eukaryotic nucleases; nonsense-mediated mRNA decay and nonsense-associated altered splicing; Cis-acting sequences/Trans-acting factors of mRNA decay; translational accuracy; multicomponent bacterial nucleases; interplay between mRNA polyadenylation, translation and decay in prokaryotes and prokaryotic organelles; and RNA interference and other RNA mediators of gene expression. In addition to the talks and two poster sessions, there were three round tables: (1) Does translation occur in the nucleus? (2) Differences and similarities in the mechanisms of mRNA decay in different eukaryotes, and (3) RNA surveillance in bacteria?

  14. Functional characterization of the cutI gene for the transcription of carbon monoxide dehydrogenase genes in Mycobacterium sp. strain JC1 DSM 3803.

    PubMed

    Lee, Jae Ho; Park, Sae Woong; Kim, Young Min; Oh, Jeong-Il

    2017-01-01

    Carbon monoxide dehydrogenase (CO-DH) in Mycobacterium sp. strain JC1 is a key enzyme for the carboxydotrophic growth, when carbon monoxide (CO) is supplied as a sole source of carbon and energy. This enzyme is also known to act as nitric oxide dehydrogenase (NO-DH) for the detoxification of NO. Several accessory genes such as cutD, cutE, cutF, cutG, cutH, and cutI, are clustered together with two copies of the CO-DH structural genes (cutB1C1A1 and cutB2C2A2) in Mycobacterium sp. strain JC1 and are well conserved in carboxydotrophic mycobacteria. Transcription of the CO-DH structural and accessory genes was demonstrated to be increased significantly by acidified sodium nitrate as a source of NO. A cutI deletion (ΔcutI) mutant of Mycobacterium sp. strain JC1 was generated to identity the function of CutI. Lithoautotrophic growth of the ΔcutI mutant was severely affected in mineral medium supplemented with CO, while the mutant grew normally with glucose. Western blotting, CO-DH activity staining, and CO-DH-specific enzyme assay revealed a significant decrease in the cellular level of CO-DH in the ΔcutI mutant. Northern blot analysis and promoter assay showed that expression of the cutB1 and cutB2 genes was significantly reduced at the transcriptional level in the ΔcutI mutant, compared to that of the wildtype strain. The ΔcutI mutant was much more susceptible to NO than was the wild type.

  15. Material cutting, shaping, and forming: A compilation

    NASA Technical Reports Server (NTRS)

    1974-01-01

    Information is presented concerning cutting, shaping, and forming of materials, and the equipment and techniques required for utilizing these materials. The use of molds, electrical fields, and mechanical devices are related to forming materials. Material cutting methods by devices including borers and slicers are presented along with chemical techniques. Shaping and fabrication techniques are described for tubing, honeycomb panels, and ceramic structures. The characteristics of the materials are described. Patent information is included.

  16. Cutting Symmetrical Recesses In Soft Ceramic Tiles

    NASA Technical Reports Server (NTRS)

    Nesotas, Tony C.; Tyler, Brent

    1989-01-01

    Simple tool cuts hemispherical recesses in soft ceramic tiles. Designed to expose wires of thermocouples embedded in tiles without damaging leads. Creates neat, precise holes around wires. End mill includes axial hole to accommodate thermocouple wires embedded in material to be cut. Wires pass into hole without being bent or broken. Dimensions in inches. Used in place of such tools as dental picks, tweezers, spatulas, and putty knives.

  17. Cutting Symmetrical Recesses In Soft Ceramic Tiles

    NASA Technical Reports Server (NTRS)

    Nesotas, Tony C.; Tyler, Brent

    1989-01-01

    Simple tool cuts hemispherical recesses in soft ceramic tiles. Designed to expose wires of thermocouples embedded in tiles without damaging leads. Creates neat, precise holes around wires. End mill includes axial hole to accommodate thermocouple wires embedded in material to be cut. Wires pass into hole without being bent or broken. Dimensions in inches. Used in place of such tools as dental picks, tweezers, spatulas, and putty knives.

  18. Mechanical Cutting of Irradiated Reactor Internal Components

    SciTech Connect

    Anderson, M.G.; Fennema, J.A.

    2007-07-01

    This paper discusses the use of mechanical cutting methods to volume reduce and package irradiated reactor internal components. The recent completion of the removal of the Reactor Vessel Internals (RVI) from within the Sacramento Municipal Utility District's (SMUD) Rancho Seco Nuclear Power Plant demonstrates that unlike previous methods used for similar projects, mechanical cutting minimizes exposure to workers, costly water cleanup, and excessive secondary waste generation. (authors)

  19. Demonstrating diamond wire cutting of the TFTR

    SciTech Connect

    Rule, K.; Perry, E.; Larson, S.; Viola, M.

    2000-02-24

    The Tokamak Fusion Test Reactor (TFTR) ceased operation in April 1997 and decommissioning commenced in October 1999. The deuterium-tritium fusion experiments resulted in contaminating the vacuum vessel with tritium and activating the materials with 14 Mev neutrons. The total tritium content within the vessel is in excess of 7,000 Curies while dose rates approach 50 mRem/hr. These radiological hazards along with the size of the Tokamak (100 cubic meters) present a unique and challenging task for dismantling. Plasma arc cutting is the current baseline technology for the dismantlement of fission reactors. This technology is typically used because of its faster cutting times. Alternatively, an innovative approach for dismantlement of the TFTR is the use of diamond wire cutting technology. Recent improvements in diamond wire technology have allowed the cutting of carbon steel components such as pipe, plate, and tube bundles in heat exchangers. Some expected benefits of this technology include: significantly reduction in airborne contaminates, reduced personnel exposure, a reduced risk of spread of tritium contamination, and reduced overall costs as compared to using plasma arc cutting. This paper will provide detailed results of the diamond wire cutting demonstration that was completed in September of 1999, on a mock-up of this complex reactor. The results will identify cost, safety, industrial and engineering parameters, and the related performance of each situation.

  20. Quantum Max-flow/Min-cut

    SciTech Connect

    Cui, Shawn X.; Freedman, Michael H.; Sattath, Or; Stong, Richard Minton, Greg

    2016-06-15

    The classical max-flow min-cut theorem describes transport through certain idealized classical networks. We consider the quantum analog for tensor networks. By associating an integral capacity to each edge and a tensor to each vertex in a flow network, we can also interpret it as a tensor network and, more specifically, as a linear map from the input space to the output space. The quantum max-flow is defined to be the maximal rank of this linear map over all choices of tensors. The quantum min-cut is defined to be the minimum product of the capacities of edges over all cuts of the tensor network. We show that unlike the classical case, the quantum max-flow=min-cut conjecture is not true in general. Under certain conditions, e.g., when the capacity on each edge is some power of a fixed integer, the quantum max-flow is proved to equal the quantum min-cut. However, concrete examples are also provided where the equality does not hold. We also found connections of quantum max-flow/min-cut with entropy of entanglement and the quantum satisfiability problem. We speculate that the phenomena revealed may be of interest both in spin systems in condensed matter and in quantum gravity.

  1. Cutting injuries in an academic pathology department.

    PubMed

    Pritt, Bobbi S; Waters, Brenda L

    2005-08-01

    Cutting injuries pose an infrequent but serious threat to anatomic pathology personnel. Although cut-resistant gloves may reduce this danger, it is imperative to recognize specific behaviors that increase the chance of an injury. To examine the incidence of cutting injuries in an academic pathology department and the mechanisms by which such injuries occurred. Hospital Report of Event forms completed for laboratory incidents of cutting injury from March 1998 to September 2003 were evaluated. Further information regarding the incidents was obtained, when possible, by interviews with those personnel involved. A university-based pathology laboratory was the setting for this study. On average, 505 autopsies and 29,000 surgical specimens were processed each year during the 5.5-year time period. Pathology attending physicians, residents, dieners, and pathologists' assistants who performed autopsies and surgical specimen examinations. Eight scalpel injuries occurred during the study period. No needle-stick injuries were reported. Searching for lymph nodes and cutting firm tissue each accounted for 3 of the injuries. Only 2 of the 8 individuals were in compliance with the departmental policy regarding protective glove wear. Hospital Report of Event forms alone failed to elicit sufficient detail regarding the mechanism of injury. A laboratory-based form may be necessary to supplement the hospital form, so as to obtain full details of each injury. This information may then be disseminated to all who handle blades, with the goal of preventing future cutting injuries.

  2. Structure and Function of CutC Choline Lyase from Human Microbiota Bacterium Klebsiella pneumoniae.

    PubMed

    Kalnins, Gints; Kuka, Janis; Grinberga, Solveiga; Makrecka-Kuka, Marina; Liepinsh, Edgars; Dambrova, Maija; Tars, Kaspars

    2015-08-28

    CutC choline trimethylamine-lyase is an anaerobic bacterial glycyl radical enzyme (GRE) that cleaves choline to produce trimethylamine (TMA) and acetaldehyde. In humans, TMA is produced exclusively by the intestinal microbiota, and its metabolite, trimethylamine oxide, has been associated with a higher risk of cardiovascular diseases. Therefore, information about the three-dimensional structures of TMA-producing enzymes is important for microbiota-targeted drug discovery. We have cloned, expressed, and purified the CutC GRE and the activating enzyme CutD from Klebsiella pneumoniae, a representative of the human microbiota. We have determined the first crystal structures of both the choline-bound and choline-free forms of CutC and have discovered that binding of choline at the ligand-binding site triggers conformational changes in the enzyme structure, a feature that has not been observed for any other characterized GRE.

  3. Laser cutting of various materials: Kerf width size analysis and life cycle assessment of cutting process

    NASA Astrophysics Data System (ADS)

    Yilbas, Bekir Sami; Shaukat, Mian Mobeen; Ashraf, Farhan

    2017-08-01

    Laser cutting of various materials including Ti-6Al-4V alloy, steel 304, Inconel 625, and alumina is carried out to assess the kerf width size variation along the cut section. The life cycle assessment is carried out to determine the environmental impact of the laser cutting in terms of the material waste during the cutting process. The kerf width size is formulated and predicted using the lump parameter analysis and it is measured from the experiments. The influence of laser output power and laser cutting speed on the kerf width size variation is analyzed using the analytical tools including scanning electron and optical microscopes. In the experiments, high pressure nitrogen assisting gas is used to prevent oxidation reactions in the cutting section. It is found that the kerf width size predicted from the lump parameter analysis agrees well with the experimental data. The kerf width size variation increases with increasing laser output power. However, this behavior reverses with increasing laser cutting speed. The life cycle assessment reveals that material selection for laser cutting is critical for the environmental protection point of view. Inconel 625 contributes the most to the environmental damages; however, recycling of the waste of the laser cutting reduces this contribution.

  4. Final Report

    SciTech Connect

    Webb, Robert C.; Kamon, Teruki; Toback, David; Safonov, Alexei; Dutta, Bhaskar; Dimitri, Nanopoulos; Pope, Christopher; White, James

    2013-11-18

    Overview The High Energy Physics Group at Texas A&M University is submitting this final report for our grant number DE-FG02-95ER40917. This grant has supported our wide range of research activities for over a decade. The reports contained here summarize the latest work done by our research team. Task A (Collider Physics Program): CMS & CDF Profs. T. Kamon, A. Safonov, and D. Toback co-lead the Texas A&M (TAMU) collider program focusing on CDF and CMS experiments. Task D: Particle Physics Theory Our particle physics theory task is the combined effort of Profs. B. Dutta, D. Nanopoulos, and C. Pope. Task E (Underground Physics): LUX & NEXT Profs. R. Webb and J. White(deceased) lead the Xenon-based underground research program consisting of two main thrusts: the first, participation in the LUX two-phase xenon dark matter search experiment and the second, detector R&D primarily aimed at developing future detectors for underground physics (e.g. NEXT and LZ).

  5. The bereft gene, a potential target of the neural selector gene cut, contributes to bristle morphogenesis.

    PubMed Central

    Hardiman, Kirsten E; Brewster, Rachel; Khan, Shaema M; Deo, Monika; Bodmer, Rolf

    2002-01-01

    The neural selector gene cut, a homeobox transcription factor, is required for the specification of the correct identity of external (bristle-type) sensory organs in Drosophila. Targets of cut function, however, have not been described. Here, we study bereft (bft) mutants, which exhibit loss or malformation of a majority of the interommatidial bristles of the eye and cause defects in other external sensory organs. These mutants were generated by excising a P element located at chromosomal location 33AB, the enhancer trap line E8-2-46, indicating that a gene near the insertion site is responsible for this phenotype. Similar to the transcripts of the gene nearest to the insertion, reporter gene expression of E8-2-46 coincides with Cut in the support cells of external sensory organs, which secrete the bristle shaft and socket. Although bft transcripts do not obviously code for a protein product, its expression is abolished in bft deletion mutants, and the integrity of the bft locus is required for (interommatidial) bristle morphogenesis. This suggests that disruption of the bft gene is the cause of the observed bristle phenotype. We also sought to determine what factors regulate the expression of bft and the enhancer trap line. The correct specification of individual external sensory organ cells involves not only cut, but also the lineage genes numb and tramtrack. We demonstrate that mutations of these three genes affect the expression levels at the bft locus. Furthermore, cut overexpression is sufficient to induce ectopic bft expression in the PNS and in nonneuronal epidermis. On the basis of these results, we propose that bft acts downstream of cut and tramtrack to implement correct bristle morphogenesis. PMID:12019237

  6. Influence of Cutting Parameters and Tool Wear on the Surface Integrity of Cobalt-Based Stellite 6 Alloy When Machined Under a Dry Cutting Environment

    NASA Astrophysics Data System (ADS)

    Yingfei, Ge; de Escalona, Patricia Muñoz; Galloway, Alexander

    2016-11-01

    The efficiency of a machining process can be measured by evaluating the quality of the machined surface and the tool wear rate. The research reported herein is mainly focused on the effect of cutting parameters and tool wear on the machined surface defects, surface roughness, deformation layer and residual stresses when dry milling Stellite 6, deposited by overlay on a carbon steel surface. The results showed that under the selected cutting conditions, abrasion, diffusion, peeling, chipping and breakage were the main tool wear mechanisms presented. Also the feed rate was the primary factor affecting the tool wear with an influence of 83%. With regard to the influence of cutting parameters on the surface roughness, the primary factors were feed rate and cutting speed with 57 and 38%, respectively. In addition, in general, as tool wear increased, the surface roughness increased and the deformation layer was found to be influenced more by the cutting parameters rather than the tool wear. Compressive residual stresses were observed in the un-machined surface, and when machining longer than 5 min, residual stress changed 100% from compression to tension. Finally, results showed that micro-crack initiation was the main mechanism for chip formation.

  7. Influence of Cutting Parameters and Tool Wear on the Surface Integrity of Cobalt-Based Stellite 6 Alloy When Machined Under a Dry Cutting Environment

    NASA Astrophysics Data System (ADS)

    Yingfei, Ge; de Escalona, Patricia Muñoz; Galloway, Alexander

    2017-01-01

    The efficiency of a machining process can be measured by evaluating the quality of the machined surface and the tool wear rate. The research reported herein is mainly focused on the effect of cutting parameters and tool wear on the machined surface defects, surface roughness, deformation layer and residual stresses when dry milling Stellite 6, deposited by overlay on a carbon steel surface. The results showed that under the selected cutting conditions, abrasion, diffusion, peeling, chipping and breakage were the main tool wear mechanisms presented. Also the feed rate was the primary factor affecting the tool wear with an influence of 83%. With regard to the influence of cutting parameters on the surface roughness, the primary factors were feed rate and cutting speed with 57 and 38%, respectively. In addition, in general, as tool wear increased, the surface roughness increased and the deformation layer was found to be influenced more by the cutting parameters rather than the tool wear. Compressive residual stresses were observed in the un-machined surface, and when machining longer than 5 min, residual stress changed 100% from compression to tension. Finally, results showed that micro-crack initiation was the main mechanism for chip formation.

  8. Nitinol laser cutting: microstructure and functional properties of femtosecond and continuous wave laser processing

    NASA Astrophysics Data System (ADS)

    Biffi, C. A.; Tuissi, A.

    2017-03-01

    Thermal processing can affect the properties of smart materials, and the correct selection of the best manufacturing technology is fundamental for producing high tech smart devices, containing embedded functional properties. In this work cutting of thin superelastic Nitinol plates using a femtosecond (fs) and continuous wave (CW) laser was studied. Diamond shaped elements were cut to characterize the kerf qualitative features; microstructural analysis of the cross sections allowed identification of thermal damage characteristics introduced into the material during the laser processes. A thermally undamaged microstructure was observed for fs laser cutting, while CW was seen to be characterized by a large heat-affected zone. Functional properties were investigated by differential scanning calorimetry and tensile testing of laser cut microelements and of the reference material. It was seen that the martensitic transformation behavior of Nitinol is not affected by fs regime, while cw cutting provokes an effect equivalent to a high temperature thermal treatment in the material surrounding the cutting kerf, degradating the material properties. Finally, tensile testing indicated that superelastic performances were guaranteed by fs regime, while strong reduction of the recoverable strain was detected in the CW processed sample.

  9. New tooling for plasma cutting technology

    NASA Astrophysics Data System (ADS)

    Korotkikh, M. T.; Shaterin, M. A.; Shterin, V. B.

    1985-03-01

    When milling the edges of sheet intermediate products made of high strength manganese and other special steels and alloys with plasma preheating, milling cutters equipped with plates of metal-ceramic hard alloys are used. With plasma heating, it is most advisable to use cylindrical milling tools. The tooth of the milling tool cuts into the soft metal which reduces the unit loads on the cutting wedge of the tool. It becomes possible to use plates with the slope angle of the cutting edge equal or near zero, which considerably simplifies the making of the tool. The milling tool design makes it technologically efficient to produce basing surfaces for setting the cutting components. The through wedge grooves of the rings may be ground which produces very flat supporting surfaces and, therefore, high rigidity of the interface between the plate and the support. The use of tetrahedral plates with a flat forward surface with a 90 deg tip angle utilizes all eight cutting edges of the plate. The use of such milling tools with plasma preheating of the intermediate product insures high machining productivity even if the tool is equipped with hard alloy plates without tungsten.

  10. Final Report

    SciTech Connect

    Callis, Judy

    2016-11-30

    This report summarizes our research activities. In the award period, we have made significant progress on the first aim, with new discoveries reported in one published paper (1) and in one submitted manuscript (2) currently under review. The published manuscript reports on our discovery of plant ribokinase and the metabolic pathway in which it functions; the submitted manuscript is identification and characterization of the plant fructokinase family of enzymes from expression studies, sequence comparisons, subcellular localizations and enzymatic activities of recombinant proteins. Our study of loss-of-function mutants in the fructokinase family members (2) revealed that there were no phenotypic differences observed for the five genes analyzed, so we have adopted the Crispr/Cas9 system to isolate mutants in the two genes for which there are no currently available insertion mutants, and we are generating higher order mutants (double, triples, etc) to discern the relative roles and significance for each fructokinase. These mutants will be an important resource to understand regulation of carbohydrate movement and catabolism in plants. As studies from others indicate, alteration of fructokinases results in changes in cell walls and vasculatures, which have importance relative to biofuel yield and quality. In the second aim, we have characterized the protein-protein interactions for the pkfB proteins FLN1 and FLN2 that are localized to chloroplast transcriptional complexes and have proposed a new model for how chloroplast transcription is regulated. This work has been submitted for publication, been revised and will be re-submitted in December 2016

  11. Final Report

    SciTech Connect

    Wessels, B. W.

    2002-08-02

    Final report for program on the study of structure and properties of epitaxial oxide films. The defect structure of epitaxial oxide thin films was investigated. Both binary and complex oxides were studied. Epitaxial oxides were synthesized by organometallic chemical vapor deposition (OMCVD). This technique has been found to be highly versatile for the synthesis of a wide range of epitaxial oxide including dielectrics, ferroelectrics and high T{sub c} superconductors. Systems investigated include the binary oxides ZnO and TiO{sub 2} and ferroelectric oxides BaTiO{sub 3}, BaSrTiO{sub 3} and KNbO{sub 3}. Techniques used to evaluate the defect structure included deep level transient spectroscopy (DLTS), photocapacitance spectroscopy, and photoluminescence (PL) spectroscopy. High purity, stoichiometric oxide films were deposited and their defect structure evaluated. Epitaxial ZnO was deposited at temperatures as low as 250 C. PL indicated only near band edge ultraviolet emission showing that both extrinsic and intrinsic point defects could be significantly lowered in OMCVD derived thin films compared to that of the bulk. This presumably was a result of low deposition temperatures and high purity starting materials. Ferroelectric oxides epitaxial thin films of BaTiO{sub 3} and the solid solution BaSrTiO{sub 3} were synthesized and the defect structure determined. Photocapacitance spectroscopy was developed to quantify electrically active defects in the oxides. Defects with concentrations as low as 10{sup 14} cm{sup -3} were observed and their properties determined. A new model was developed for the electronic transport properties of intrinsic and extrinsic BaTiO{sub 3}. A transport model was proposed whereby conduction in La doped films occurs via hopping in localized states within a pseudogap formed between a lower Hubbard band and the conduction band edge. The influence of the size effect on the ferroelectric phase transition in the thin films was investigated. The

  12. Budget Cuts: Financial Aid Offices Face Budget Cuts and Increasing Workload. Quick Scan Survey Results

    ERIC Educational Resources Information Center

    National Association of Student Financial Aid Administrators (NJ1), 2010

    2010-01-01

    The majority of college financial aid offices have seen cuts to their operating budgets this year compared to the 2007-08 academic year when the recession began, according to the National Association of Student Financial Aid Administrator's latest QuickScan Survey. Sixty-two percent of financial aid offices reported operating budget cuts this year…

  13. Rationalizing IT Rationing: 10 Ways to Cut the IT Budget (and What Not to Cut)

    ERIC Educational Resources Information Center

    Miller, Fred

    2009-01-01

    Whether because of falling stock values affecting institutional endowments, cutbacks in state spending, or declines in private giving, higher education has reduced spending, and information technology (IT) organizations have participated in the budget cuts. This is the tale of one institution's quest to cut technology costs while maintaining a…

  14. Rationalizing IT Rationing: 10 Ways to Cut the IT Budget (and What Not to Cut)

    ERIC Educational Resources Information Center

    Miller, Fred

    2009-01-01

    Whether because of falling stock values affecting institutional endowments, cutbacks in state spending, or declines in private giving, higher education has reduced spending, and information technology (IT) organizations have participated in the budget cuts. This is the tale of one institution's quest to cut technology costs while maintaining a…

  15. Laser cutting of rectangular geometry into aluminum alloy: Effect of cut sizes on thermal stress field

    NASA Astrophysics Data System (ADS)

    Akhtar, Sohail; Kardas, Omer Ozgur; Keles, Omer; Yilbas, Bekir Sami

    2014-10-01

    Laser cutting of a rectangular geometry into aluminum alloy 2024 is carried out. Temperature and stress fields are predicted in the cutting section using the ABAQUS finite element code in line with the experimental conditions. Effect of the size of the rectangular geometry on the thermal stress fields is examined in the cutting section. Temperature predictions are validated through the thermocouple data. To identify the morphological changes in the cutting section, an experiment is carried out and the resulting cutting sections are examined under optical and scanning electron microscopes. It is found that temperature and stress fields are affected by the size of the rectangular cut geometry. Temperature and von Mises stress attains higher values for small size rectangular geometry as compared to its counterpart corresponding to the large size geometry. Laser cut sections are free from large size asperities including sideways burning and out-off flatness at the cut edges. Locally scattered some small dross attachments are observed at the kerf exit.

  16. Plasma Cutting and Carbon-Arc Cutting. Welding Module 8. Instructor's Guide.

    ERIC Educational Resources Information Center

    Missouri Univ., Columbia. Instructional Materials Lab.

    This guide is intended to assist vocational educators in teaching the two units of a module in operating plasma cutting and carbon-arc cutting equipment. The module is part of a welding curriculum that has been designed to be totally integrated with Missouri's Vocational Instruction Management System. The materials included in the module have been…

  17. Effect of Cutting Velocity / Stem Size on the Efficiency of NRCRI Cassave Stem Cutting Machine

    NASA Astrophysics Data System (ADS)

    Ikejiofor, M. C.

    2012-11-01

    The developed NRCRI (National Root Crops Research Institute) cassava stem cutting machine was evaluated. The cassava stems from the variety TME 419 were used. The sizes of the stem used were 1.8, 2.0, 2.3 and 2.6cm. Also, different cutting velocities of 1.20, 1.23 and 1.32m/s were used. The stakes produced has length of 2.5cm. Analysis of variance in RCBD was used to evaluate the effect of the cutting velocity and the stem size on the efficiency of the cutting machine. The result of the analysis showed that the cutting velocity had very highly significant effect, while the stem size had no significant effect at 5% level on the efficiency of the cutting machine. The data obtained also showed that the highest and least cutting efficiencies of 99.42 and 94.71% were obtained with the machine cutting velocities of 1.2 and 1.32m/s respectively.

  18. Recycling stabilised/solidified drill cuttings for forage production in acidic soils.

    PubMed

    Kogbara, Reginald B; Dumkhana, Bernard B; Ayotamuno, Josiah M; Okparanma, Reuben N

    2017-10-01

    Stabilisation/solidification (S/S), which involves fixation and immobilisation of contaminants using cementitious materials, is one method of treating drill cuttings before final fate. This work considers reuse of stabilised/solidified drill cuttings for forage production in acidic soils. It sought to improve the sustainability of S/S technique through supplementation with the phytoremediation potential of plants, eliminate the need for landfill disposal and reduce soil acidity for better plant growth. Drill cuttings with an initial total petroleum hydrocarbon (TPH) concentration of 17,125 mg kg(-1) and low concentrations of metals were treated with 5%, 10%, and 20% cement dosages. The treated drill cuttings were reused in granular form for growing a forage, elephant grass (Pennisetum purpureum), after mixing with uncontaminated soil. The grasses were also grown in uncontaminated soil. The phytoremediation and growth potential of the plants was assessed over a 12-week period. A mix ratio of one part drill cuttings to three parts uncontaminated soil was required for active plant growth. The phytoremediation ability of elephant grass (alongside abiotic losses) reduced the TPH level (up to 8795 mg kg(-1)) in the soil-treated-drill cuttings mixtures below regulatory (1000 mg kg(-1)) levels. There were also decreased concentrations of metals. The grass showed better heights and leaf lengths in soil containing drill cuttings treated with 5% cement dosage than in uncontaminated soil. The results suggest that recycling S/S treated drill cuttings for forage production may be a potential end use of the treated waste. Copyright © 2017 Elsevier Ltd. All rights reserved.

  19. Modified atmosphere packaging for fresh-cut fruits and vegetables

    USDA-ARS?s Scientific Manuscript database

    The latest development in and different aspects of modified atmosphere packaging for fresh-cut fruits and vegetables are reviewed in the book. This book provides all readers, including fresh-cut academic researchers, fresh-cut R&D personnel, and fresh-cut processing engineers, with unique, essential...

  20. Collecting dormant hardwood cuttings for western riparian restoration projects

    Treesearch

    Tara Luna; R. Kasten Dumroese; Thomas D. Landis

    2006-01-01

    Dormant hardwood cuttings are sections of woody stems that can develop into new plants complete with stems, leaves, and roots. Cuttings differ from seedlings because all new daughter plants that arise from cuttings are genetically identical to the parent plant. Cuttings can be long or short, depending on how they are used.

  1. 7 CFR 318.13-23 - Cut flowers from Hawaii.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 7 Agriculture 5 2010-01-01 2010-01-01 false Cut flowers from Hawaii. 318.13-23 Section 318.13-23... From Hawaii and the Territories § 318.13-23 Cut flowers from Hawaii. (a) Except for cut blooms and leis... paragraph (b) of this section, cut flowers may be moved interstate from Hawaii under limited permit, to a...

  2. 7 CFR 318.13-23 - Cut flowers from Hawaii.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 7 Agriculture 5 2011-01-01 2011-01-01 false Cut flowers from Hawaii. 318.13-23 Section 318.13-23... From Hawaii and the Territories § 318.13-23 Cut flowers from Hawaii. (a) Except for cut blooms and leis... paragraph (b) of this section, cut flowers may be moved interstate from Hawaii under limited permit, to a...

  3. 49 CFR 213.352 - Torch cut rail.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 4 2011-10-01 2011-10-01 false Torch cut rail. 213.352 Section 213.352... Torch cut rail. (a) Except as a temporary repair in emergency situations no rail having a torch cut end shall be used. When a rail end with a torch cut is used in emergency situations, train speed over that...

  4. 49 CFR 213.352 - Torch cut rail.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 49 Transportation 4 2013-10-01 2013-10-01 false Torch cut rail. 213.352 Section 213.352... Torch cut rail. (a) Except as a temporary repair in emergency situations no rail having a torch cut end shall be used. When a rail end with a torch cut is used in emergency situations, train speed over that...

  5. 49 CFR 236.52 - Relayed cut-section.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 49 Transportation 4 2013-10-01 2013-10-01 false Relayed cut-section. 236.52 Section 236.52...: All Systems Track Circuits § 236.52 Relayed cut-section. Where relayed cut-section is used in... shall be open and the track circuit shunted when the track relay at such cut-section is in deenergized...

  6. 49 CFR 213.352 - Torch cut rail.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 4 2012-10-01 2012-10-01 false Torch cut rail. 213.352 Section 213.352... Torch cut rail. (a) Except as a temporary repair in emergency situations no rail having a torch cut end shall be used. When a rail end with a torch cut is used in emergency situations, train speed over that...

  7. 21 CFR 882.4275 - Dowel cutting instrument.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Dowel cutting instrument. 882.4275 Section 882...) MEDICAL DEVICES NEUROLOGICAL DEVICES Neurological Surgical Devices § 882.4275 Dowel cutting instrument. (a) Identification. A dowel cutting instrument is a device used to cut dowels of bone for bone grafting. (b...

  8. 21 CFR 882.4275 - Dowel cutting instrument.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Dowel cutting instrument. 882.4275 Section 882...) MEDICAL DEVICES NEUROLOGICAL DEVICES Neurological Surgical Devices § 882.4275 Dowel cutting instrument. (a) Identification. A dowel cutting instrument is a device used to cut dowels of bone for bone grafting. (b...

  9. 49 CFR 213.352 - Torch cut rail.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false Torch cut rail. 213.352 Section 213.352... Torch cut rail. (a) Except as a temporary repair in emergency situations no rail having a torch cut end shall be used. When a rail end with a torch cut is used in emergency situations, train speed over that...

  10. 49 CFR 236.52 - Relayed cut-section.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 4 2011-10-01 2011-10-01 false Relayed cut-section. 236.52 Section 236.52...: All Systems Track Circuits § 236.52 Relayed cut-section. Where relayed cut-section is used in... shall be open and the track circuit shunted when the track relay at such cut-section is in deenergized...

  11. 7 CFR 58.413 - Cutting and packaging rooms.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 7 Agriculture 3 2012-01-01 2012-01-01 false Cutting and packaging rooms. 58.413 Section 58.413....413 Cutting and packaging rooms. When small packages of cheese are cut and wrapped, separate rooms shall be provided for the cleaning and preparation of the bulk cheese and for the cutting and wrapping...

  12. 21 CFR 882.4275 - Dowel cutting instrument.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Dowel cutting instrument. 882.4275 Section 882...) MEDICAL DEVICES NEUROLOGICAL DEVICES Neurological Surgical Devices § 882.4275 Dowel cutting instrument. (a) Identification. A dowel cutting instrument is a device used to cut dowels of bone for bone grafting. (b...

  13. 7 CFR 58.413 - Cutting and packaging rooms.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 7 Agriculture 3 2011-01-01 2011-01-01 false Cutting and packaging rooms. 58.413 Section 58.413....413 Cutting and packaging rooms. When small packages of cheese are cut and wrapped, separate rooms shall be provided for the cleaning and preparation of the bulk cheese and for the cutting and wrapping...

  14. 21 CFR 882.4275 - Dowel cutting instrument.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Dowel cutting instrument. 882.4275 Section 882...) MEDICAL DEVICES NEUROLOGICAL DEVICES Neurological Surgical Devices § 882.4275 Dowel cutting instrument. (a) Identification. A dowel cutting instrument is a device used to cut dowels of bone for bone grafting. (b...

  15. 7 CFR 58.413 - Cutting and packaging rooms.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 7 Agriculture 3 2014-01-01 2014-01-01 false Cutting and packaging rooms. 58.413 Section 58.413....413 Cutting and packaging rooms. When small packages of cheese are cut and wrapped, separate rooms shall be provided for the cleaning and preparation of the bulk cheese and for the cutting and wrapping...

  16. 49 CFR 236.52 - Relayed cut-section.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false Relayed cut-section. 236.52 Section 236.52...: All Systems Track Circuits § 236.52 Relayed cut-section. Where relayed cut-section is used in... shall be open and the track circuit shunted when the track relay at such cut-section is in deenergized...

  17. 36 CFR 223.14 - Where timber may be cut.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 36 Parks, Forests, and Public Property 2 2013-07-01 2013-07-01 false Where timber may be cut. 223... General Provisions § 223.14 Where timber may be cut. (a) The cutting of trees, portions of trees or other... a grantor of land, during the life of such reservation. (2) Timber reserved from cutting under other...

  18. 49 CFR 236.52 - Relayed cut-section.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 4 2012-10-01 2012-10-01 false Relayed cut-section. 236.52 Section 236.52...: All Systems Track Circuits § 236.52 Relayed cut-section. Where relayed cut-section is used in... shall be open and the track circuit shunted when the track relay at such cut-section is in deenergized...

  19. 49 CFR 236.52 - Relayed cut-section.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 49 Transportation 4 2014-10-01 2014-10-01 false Relayed cut-section. 236.52 Section 236.52...: All Systems Track Circuits § 236.52 Relayed cut-section. Where relayed cut-section is used in... shall be open and the track circuit shunted when the track relay at such cut-section is in deenergized...

  20. 36 CFR 223.14 - Where timber may be cut.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 36 Parks, Forests, and Public Property 2 2011-07-01 2011-07-01 false Where timber may be cut. 223... General Provisions § 223.14 Where timber may be cut. (a) The cutting of trees, portions of trees or other... a grantor of land, during the life of such reservation. (2) Timber reserved from cutting under other...

  1. 21 CFR 882.4275 - Dowel cutting instrument.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Dowel cutting instrument. 882.4275 Section 882...) MEDICAL DEVICES NEUROLOGICAL DEVICES Neurological Surgical Devices § 882.4275 Dowel cutting instrument. (a) Identification. A dowel cutting instrument is a device used to cut dowels of bone for bone grafting. (b...

  2. 49 CFR 213.352 - Torch cut rail.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 49 Transportation 4 2014-10-01 2014-10-01 false Torch cut rail. 213.352 Section 213.352... Torch cut rail. (a) Except as a temporary repair in emergency situations no rail having a torch cut end shall be used. When a rail end with a torch cut is used in emergency situations, train speed over that...

  3. A Class of Cuts and Related Algorithms in Integer Programming.

    DTIC Science & Technology

    A new family of intersection cuts is obtained from a class of convex polyhedra (generalized octahedra). It is shown that these cuts can also be...obtained as convex combinations of the Gomory mixed integer cuts . A constructive approach to obtain improved (i.e. deeper) cuts is then presented and discussed. (Author)

  4. 7 CFR 58.413 - Cutting and packaging rooms.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 7 Agriculture 3 2013-01-01 2013-01-01 false Cutting and packaging rooms. 58.413 Section 58.413....413 Cutting and packaging rooms. When small packages of cheese are cut and wrapped, separate rooms shall be provided for the cleaning and preparation of the bulk cheese and for the cutting and wrapping...

  5. 36 CFR 223.14 - Where timber may be cut.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 36 Parks, Forests, and Public Property 2 2014-07-01 2014-07-01 false Where timber may be cut. 223... General Provisions § 223.14 Where timber may be cut. (a) The cutting of trees, portions of trees or other... a grantor of land, during the life of such reservation. (2) Timber reserved from cutting under other...

  6. Physiology of fresh-cut fruits and vegetables

    USDA-ARS?s Scientific Manuscript database

    The idea to pre-process fruits and vegetables in the fresh state started with fresh-cut salads and now has expanded to fresh-cut fruits and other vegetables. The fresh-cut portion of the fresh produce industry includes fruits, vegetables, sprouts, mushrooms and even herbs that are cut, cored, sliced...

  7. New oxygen plasma process rivals laser cutting methods

    SciTech Connect

    Fernicola, R.C. )

    1994-06-01

    For many years, oxygen plasma cutting has been looked upon as a desirable process for cutting steel but not practical in production because of very short consumable parts life. Recently, a number of technical advances in the oxygen plasma cutting process provides parts life several times that of older systems and cut quality approaching that of laser systems. This paper discusses these advances.

  8. 7 CFR 58.413 - Cutting and packaging rooms.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 7 Agriculture 3 2010-01-01 2010-01-01 false Cutting and packaging rooms. 58.413 Section 58.413....413 Cutting and packaging rooms. When small packages of cheese are cut and wrapped, separate rooms... outward to minimize the entrance of unfiltered air into the cutting and packaging room. The...

  9. 43 CFR 5463.1 - Time for cutting and removal.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 43 Public Lands: Interior 2 2011-10-01 2011-10-01 false Time for cutting and removal. 5463.1... Cutting and Removal § 5463.1 Time for cutting and removal. Time for cutting and removal of timber or other vegetative resources sold shall not exceed a period of thirty-six months except that such time for...

  10. 43 CFR 5463.1 - Time for cutting and removal.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... MANAGEMENT, DEPARTMENT OF THE INTERIOR FOREST MANAGEMENT (5000) SALES ADMINISTRATION Expiration of Time for Cutting and Removal § 5463.1 Time for cutting and removal. Time for cutting and removal of timber or other... 43 Public Lands: Interior 2 2014-10-01 2014-10-01 false Time for cutting and removal. 5463.1...

  11. 43 CFR 5463.1 - Time for cutting and removal.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... MANAGEMENT, DEPARTMENT OF THE INTERIOR FOREST MANAGEMENT (5000) SALES ADMINISTRATION Expiration of Time for Cutting and Removal § 5463.1 Time for cutting and removal. Time for cutting and removal of timber or other... 43 Public Lands: Interior 2 2013-10-01 2013-10-01 false Time for cutting and removal. 5463.1...

  12. 43 CFR 5463.1 - Time for cutting and removal.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... MANAGEMENT, DEPARTMENT OF THE INTERIOR FOREST MANAGEMENT (5000) SALES ADMINISTRATION Expiration of Time for Cutting and Removal § 5463.1 Time for cutting and removal. Time for cutting and removal of timber or other... 43 Public Lands: Interior 2 2012-10-01 2012-10-01 false Time for cutting and removal. 5463.1...

  13. Selective hydrocracking of light naphtha cuts

    SciTech Connect

    Koslov, I.T.; Khavkin, V.A.; Nefedov, B.K.

    1986-03-01

    For the production of high-quality automotive gasolines, technology has been developed for a combined ''isoreforming'' process, in which hydrocracking of a heavy straight-run naphtha cut to give a high-octane component with an octane number of 84-86 (MM) is combined with catalytic reforming of the residual fraction from hydrocracking. The ''isoreforming'' technology can be used to produce AI-93 automotive gasolines with aromatic hydrocarbon contents of 45-49% by weight, without TEL, in yields of 78-82% by weight on the original feed. The authors also discuss a catalytic upgrading process for light straight-run naphtha distillates or raffinates from catalytic reforming. The influence of the depth of reaction in hydrocracking n-paraffins in the straight-run 62-105 degrees C cut on the yield of the C5-EP cut and its octane number is investigated.

  14. Dispersion analysis of arbitrarily cut orthorhombic crystals.

    PubMed

    Höfer, Sonja; Ivanovski, Vladimir; Uecker, Reinhard; Kwasniewski, Albert; Popp, Jürgen; Mayerhöfer, Thomas G

    2017-06-05

    We developed a measurement and evaluation scheme to perform dispersion analysis on arbitrarily cut orthorhombic crystals based on the schemes developed for triclinic and uniaxial crystals. As byproduct of dispersion analysis the orientations of the crystal axes are found. In contrast to the spectra of arbitrarily cut uniaxial crystals, where the fit routine has to separate two independent principal spectra, the spectra of arbitrarily cut orthorhombic crystals are a combination of three independent spectra and the evaluation scheme gets more complex. Dispersion analysis is exemplary performed on two different crystals, which show different spectral features and different levels of difficulties to evaluate. Neodymium gallate (NdGaO3) has broad overlapping reflections bands while topaz (Al2SiO4 [F, OH]2) has a quite high total number of infrared active bands. Copyright © 2017 Elsevier B.V. All rights reserved.

  15. Introduction of cutting ceramics in plants

    SciTech Connect

    Logachev, G.A.; Privalov, V.A.; Shiryaev, M.Y.; Toporkov, A.O.

    1983-09-01

    Cutting ceramics of aluminum oxide Al203 produced in the form of types V3, VOK 60, and VOK 63 triangular, square, and rhombic, by the Dnepr Sintered Carbide Plant have wide use in plants. Tools of cutting ceramics are used in mass and large lot production. The design of ceramic inserts does not differ from that of cutters designed for holding sintered carbide inserts. Cutting ceramics are used at various specified plants for machining gray irons and calendars rolls of chilled cast iron, for drilling satellite gears, and in outside machining of pins, gate valves, shafts, and rollers. Tests conducted show that ceramic inserts reduce labor costs by 1.52 times and increases tool life 2-3 times.

  16. Flow stress model in metal cutting

    NASA Technical Reports Server (NTRS)

    Black, J. T.

    1978-01-01

    A model for the plastic deformation that occurs in metal cutting, based on dislocation mechanics, is presented. The model explains the fundamental deformation structure that develops during machining and is based on the well known Cottrell-Stokes Law, wherein the flow stress is partitioned into two parts; an athermal part which occurs in the shear fronts (or shear bands); and a thermal part which occurs in the lamella regions. The deformation envokes the presence of a cellular dislocation distribution which always exists in the material ahead of the shear process. This 'alien' dislocation distribution either exists in the metal prior to cutting or is produced by the compressive stress field which operates in front of the shear process. The magnitude of the flow stress and direction of the shear are shown to be correlated to the stacking fault energy of the metal being cut. The model is tested with respect to energy consumption rates and found to be consistent with observed values.

  17. Edible coatings for fresh-cut fruits.

    PubMed

    Olivas, G I; Barbosa-Cánovas, G V

    2005-01-01

    The production of fresh-cut fruits is increasingly becoming an important task as consumers are more aware of the importance of healthy eating habits, and have less time for food preparation. A fresh-cut fruit is a fruit that has been physically altered from its original state (trimmed, peeled, washed and/or cut), but remains in a fresh state. Unfortunately since fruits have living tissue, they undergo enzymatic browning, texture decay, microbial contamination, and undesirable volatile production, highly reducing their shelf life if they are in any way wounded. Edible coatings can be used to help in the preservation of minimally processed fruits, providing a partial barrier to moisture, oxygen and carbon dioxide, improving mechanical handling properties, carrying additives, avoiding volatiles loss, and even contributing to the production of aroma volatiles.

  18. Flow stress model in metal cutting

    NASA Technical Reports Server (NTRS)

    Black, J. T.

    1978-01-01

    A model for the plastic deformation that occurs in metal cutting, based on dislocation mechanics, is presented. The model explains the fundamental deformation structure that develops during machining and is based on the well known Cottrell-Stokes Law, wherein the flow stress is partitioned into two parts; an athermal part which occurs in the shear fronts (or shear bands); and a thermal part which occurs in the lamella regions. The deformation envokes the presence of a cellular dislocation distribution which always exists in the material ahead of the shear process. This 'alien' dislocation distribution either exists in the metal prior to cutting or is produced by the compressive stress field which operates in front of the shear process. The magnitude of the flow stress and direction of the shear are shown to be correlated to the stacking fault energy of the metal being cut. The model is tested with respect to energy consumption rates and found to be consistent with observed values.

  19. Waterjet cutting: Technology and industrial applications

    SciTech Connect

    Miller, R.K.

    1990-01-01

    This book describes a machining technique called Waterjet cutting, also referred to as hydrodynamic machining. It is an advanced technology cutting tool that uses a stream of ultrahigh-pressure water forced through a sapphire nozzle. The waterjet removes workpiece material and produces a narrow kerf by the cutting action of a fine diameter, high velocity, high pressure stream of water or water-based fluid abrasives. The use of industrial robots to allow greater manipulation of the waterjet nozzle and the use of abrasive additives in the water stream have been the two factors which have resulted in the recent advance in waterjet system use. The system also produces less air, water and noise pollution than several more widely used machining techniques. The cost of new systems, maintenance and operating costs are also addressed.

  20. Cutting fluid study for single crystal silicon

    SciTech Connect

    Chargin, D.

    1998-05-05

    An empirical study was conducted to evaluate cutting fluids for Single Point Diamond Turning (SPDT) of single crystal silicon. The pH of distilled waster was adjusted with various additives the examine the effect of pH on cutting operations. Fluids which seemed to promote ductile cutting appeared to increase tool wear as well, an undesirable tradeoff. High Ph sodium hydroxide solutions showed promise for further research, as they yielded the best combination of reduced tool wear and good surface finish in the ductile regime. Negative rake tools were verified to improve the surface finish, but the negative rake tools used in the experiments also showed much higher wear than conventional 0{degree} rake tools. Effects of crystallographic orientation on SPDT, such as star patterns of fracture damage forming near the center of the samples, were observed to decrease with lower feedrates. Silicon chips were observed and photographed, indicative of a ductile materials removal process.

  1. Imaging, cutting, and collecting instrument and method

    DOEpatents

    Tench, R.J.; Siekhaus, W.J.; Balooch, M.; Balhorn, R.L.; Allen, M.J.

    1995-10-31

    Instrumentation and techniques are described to image small objects, such as but not limited to individual human chromosomes, with nanometer resolution. This instrument and method are also used to cut-off identified parts of objects, to move around and manipulate the cut-off parts on the substrate on which they are being imaged to predetermined locations on the substrate, and to remove the cut-off parts from the substrate. This is accomplished using an atomic force microscope (AFM) and by modification of the conventional cantilever stylus assembly of an AFM. The plural cantilevers are used with either sharp-tips or knife-edges. In addition, the invention can be utilized for measuring the hardness of materials. 10 figs.

  2. Photonic mesophases from cut rod rotators

    SciTech Connect

    Stelson, Angela C.; Liddell Watson, Chekesha M.; Avendano, Carlos

    2016-01-14

    The photonic band properties of random rotator mesophases are calculated using supercell methods applied to cut rods on a hexagonal lattice. Inspired by the thermodynamic mesophase for anisotropic building blocks, we vary the shape factor of cut fraction for the randomly oriented basis. We find large, stable bandgaps with high gap isotropy in the inverted and direct structures as a function of cut fraction, dielectric contrast, and filling fraction. Bandgap sizes up to 34.5% are maximized at high dielectric contrast for rods separated in a matrix. The bandgaps open at dielectric contrasts as low as 2.0 for the transverse magnetic polarization and 2.25 for the transverse electric polarization. Additionally, the type of scattering that promotes the bandgap is correlated with the effect of disorder on bandgap size. Slow light properties are investigated in waveguide geometry and slowdown factors up to 5 × 10{sup 4} are found.

  3. Biochemistry and physiological roles of enzymes that 'cut and paste' plant cell-wall polysaccharides.

    PubMed

    Franková, Lenka; Fry, Stephen C

    2013-09-01

    The plant cell-wall matrix is equipped with more than 20 glycosylhydrolase activities, including both glycosidases and glycanases (exo- and endo-hydrolases, respectively), which between them are in principle capable of hydrolysing most of the major glycosidic bonds in wall polysaccharides. Some of these enzymes also participate in the 'cutting and pasting' (transglycosylation) of sugar residues-enzyme activities known as transglycosidases and transglycanases. Their action and biological functions differ from those of the UDP-dependent glycosyltransferases (polysaccharide synthases) that catalyse irreversible glycosyl transfer. Based on the nature of the substrates, two types of reaction can be distinguished: homo-transglycosylation (occurring between chemically similar polymers) and hetero-transglycosylation (between chemically different polymers). This review focuses on plant cell-wall-localized glycosylhydrolases and the transglycosylase activities exhibited by some of these enzymes and considers the physiological need for wall polysaccharide modification in vivo. It describes the mechanism of transglycosylase action and the classification and phylogenetic variation of the enzymes. It discusses the modulation of their expression in plants at the transcriptional and translational levels, and methods for their detection. It also critically evaluates the evidence that the enzyme proteins under consideration exhibit their predicted activity in vitro and their predicted action in vivo. Finally, this review suggests that wall-localized glycosylhydrolases with transglycosidase and transglycanase abilities are widespread in plants and play important roles in the mechanism and control of plant cell expansion, differentiation, maturation, and wall repair.

  4. Final report

    SciTech Connect

    Dobbs, Fred C.

    2003-01-15

    species of flagellates, Spumella sp. and Bodo sp. (identifications are tentative) were isolated from South Oyster sediments by repetitive serial dilution/extinction method. Protistan cells were cultured with Cereal leaf Prescott medium and pelleted by centrifugation. Protistan DNAs were extracted with a DNA extraction kit (Sigma Co.) and the sequencing of their SSrDNA is underway. Finally, to follow up on our collaboration of Dr. Bill Johnson (Univ. of Utah), one of the co-PIs under the same NABIR umbrella, we are pleased to report we have successfully tested antibody-ferrographic capture of protists (See previous year's report for more background). Polyclonal FITC-conjugated antibody specific for a flagellate, Spumella sp., was produced by Rockland Inc., and we now are able to enumerate that species using ferrographic capture. There are, however, some issues of non-specific staining that remain to be resolved.

  5. Cutting boards in Salmonella cross-contamination.

    PubMed

    Cliver, Dean O

    2006-01-01

    Cutting boards are commonly perceived as important fomites in cross-contamination of foods with agents such as Salmonella spp., despite the lack of supporting epidemiological data. A variety of woods and plastics have been used to make work surfaces for cutting. In general, wood is said to dull knives less than plastic, and plastic is seen as less porous than wood. Research to model the hypothetical cross-contamination has been done in a variety of ways and has yielded a variety of results. At least some of the work with knife-scarred plastic indicates that the surface is very difficult to clean and disinfect, although this may vary among the polymers used. High-density polyethylene, which is most used in commercial applications, has been shown to delaminate in response to knife scarring. Wood is intrinsically porous, which allows food juices and bacteria to enter the body of the wood unless a highly hydrophobic residue covers the surface. The moisture is drawn in by capillary action until there is no more free fluid on the surface, at which point immigration ceases. Bacteria in the wood pores are not killed instantly, but neither do they return to the surface. Destructive sampling reveals infectious bacteria for hours, but resurrection of these bacteria via knife edges has not been demonstrated. Small plastic cutting boards can be cleaned in a dishwasher (as can some specially treated wooden boards), but the dishwasher may distribute the bacteria onto other food-contact surfaces. Most small wooden boards (i.e., those with no metal joiners in them) can be sterilized in a microwave oven, but this should be unnecessary if accumulation of food residues is prevented. However, 2 epidemiological studies seem to show that cutting board cleaning habits have little influence on the incidence of sporadic salmonellosis. Further, one of these studies indicated that use of plastic cutting boards in home kitchens is hazardous, whereas use of wooden cutting boards is not.

  6. Controlling dust from concrete saw cutting.

    PubMed

    Shepherd, Susan; Woskie, Susan

    2013-01-01

    Cutting concrete with gas-powered saws is ubiquitous in the construction industry and a source of exposure to respirable crystalline silica. Volunteers from the New England Laborers Training Center were recruited to participate in a field experiment examining dust reductions through the use of water, from a hose and from a sprayer, as a dust control. In four series of tests, reinforced concrete pipe was cut under both "dry" and "wet" control conditions. Overall, the geometric mean respirable dust concentration for "dry" cutting (14.396 mg/m³) exceeded both types of water-based controls by more than tenfold. Wet cutting reduced the respirable dust concentration by 85% compared with dry cutting when comparing tests paired by person and saw blade (n = 79 pairs). Using a respirable cyclone, a total of 178 samples were taken. Due to the high variability in dust exposure found in this and other studies of saw cutting, the data were examined for potential exposure determinants that contribute to that variability. Using mixed models, three fixed effects were statistically significant: control condition, worker experience, and location. A random effect for subject was included in the model to account for repeated measures. When each of the significant fixed effects was included with the random effect, it was apparent that inclusion of worker experience or location reduced the between-worker component of exposure variability, while inclusion of control condition (wet vs. dry) explained a large portion of the within-subject variability. Overall, the fixed effect variable for control condition explained the largest fraction of the total exposure variability.

  7. Laser cutting of thick sheet metals: Residual stress analysis

    NASA Astrophysics Data System (ADS)

    Arif, A. F. M.; Yilbas, B. S.; Aleem, B. J. Abdul

    2009-04-01

    Laser cutting of tailored blanks from a thick mild steel sheet is considered. Temperature and stress field in the cutting sections are modeled using the finite element method. The residual stress developed in the cutting section is determined using the X-ray diffraction (XRD) technique and is compared with the predictions. The structural and morphological changes in the cut section are examined using the optical microscopy and scanning electron microscopy (SEM). It is found that temperature and von Mises stress increase sharply in the cutting section, particularly in the direction normal to the cutting direction. The residual stress remains high in the region close to the cutting section.

  8. Modelling the laser fusion cutting process: I. Mathematical modelling of the cut kerf geometry for laser fusion cutting of thick metal

    NASA Astrophysics Data System (ADS)

    Duan, J.; Man, H. C.; Yue, T. M.

    2001-07-01

    A model for calculating the three-dimensional stationary geometric shape of the cutting front for laser fusion cutting is presented in this paper. The model relates the cut kerf geometry with the cut-through depth, various laser parameters such as power, speed, focus position and material thickness. In this model, the energy absorbed by the workpiece includes not only the direct energy from the laser beam but also the energy from the multiple reflections generated by the beam impinging on the cutting front of the cut kerf. The effects of multiple reflections are functions of the inclined angle of the cutting front and the cutting depth. The effects of various laser processing parameters, multiple reflections and inert gas pressure on the geometric shape of the cutting front have been analysed systematically and in detail. The model allows accurate prediction of the cut-through depth and cut-edge quality for a given set of process parameters. It also helps to explain the effect of focal position, cut-assist pressure and other parameters upon the cut-edge quality.

  9. Photothermal nanoblade for patterned cell membrane cutting

    PubMed Central

    Wu, Ting-Hsiang; Teslaa, Tara; Teitell, Michael A.; Chiou, Pei-Yu

    2010-01-01

    We report a photothermal nanoblade that utilizes a metallic nanostructure to harvest short laser pulse energy and convert it into a highly localized and specifically shaped explosive vapor bubble. Rapid bubble expansion and collapse punctures a lightly-contacting cell membrane via high-speed fluidic flows and induced transient shear stress. The membrane cutting pattern is controlled by the metallic nanostructure configuration, laser pulse polarization, and energy. Highly controllable, sub-micron sized circular hole pairs to half moon-like, or cat-door shaped, membrane cuts were realized in glutaraldehyde treated HeLa cells. PMID:21164656

  10. Stennis cuts ribbon on records retention facility

    NASA Image and Video Library

    2010-08-24

    NASA's John C. Stennis Space Center cut the ribbon Aug. 24 on a new, storm-resistant Records Retention Facility that consolidates and protects records storage at the nation's premier rocket engine test facility. This facility will also house history office operations. Participants in the ribbon-cutting included: (l to r) Gay Irby, Center Operations deputy director at Stennis; Linda Cureton, NASA chief information officer; Patrick Scheuermann, Stennis director; Jane Odom, NASA chief archivist; Dinna Cottrell, Stennis chief information officer; and James Cluff, Stennis records manager.

  11. Comprehensive Monitoring System for Cutting Process

    NASA Astrophysics Data System (ADS)

    Shibasaka, Toshiro; Goriki, Shin'ichi; Moriwaki, Toshimichi

    One of the problems of current monitoring systems is a lack of flexibility for managing changes in the machining environment. The purpose of this research is to construct a monitoring system that can cope flexibly with changes in the machining environment without sacrificing accuracy of detection. The monitoring system developed involves plural subsystems, and was applied to monitor the chipping at an end mill. The subsystems employ artificial neural networks based on the cutting force signals and the cutting conditions. The flexibility and reliability of the monitoring system were much improved by operating the subsystems in parallel.

  12. Computing of the Theoretical Value of Roughness Parameter Rz when Turning with Helical Cutting Edge

    NASA Astrophysics Data System (ADS)

    Šajgalík, Michal; Martikáň, Anton; Czán, Andrej; Pile, Jozef; Holubják, Jozef; Mrázik, Jozef

    2016-12-01

    This article describes process of computing and identifying of the value of roughness parameter Rz deduced from basic kinematic and geometric characteristics of turning technology of machining with tool with helical cutting edge. The final mathematical formula is deduced from graphic sketch of turning process and consequently identified using all the known geometric and kinematic parameters. This formula can be used to theoretic evaluation of geometric and cutting parameters influence on the quality of machined surface determined by roughness characteristic of theoretic parameter Rz.

  13. Minimization and Mitigation of Wire EDM Cutting Errors in the Application of the Contour Method of Residual Stress Measurement

    NASA Astrophysics Data System (ADS)

    Ahmad, Bilal; Fitzpatrick, Michael E.

    2016-01-01

    The contour method of residual stress measurement relies on the careful application of wire electro-discharge machining (WEDM) for the cutting stage. Changes in material removal rates during the cut lead to errors in the final calculated values of residual stress. In this study, WEDM cutting parameters have been explored to identify the optimum conditions for contour method residual stress measurements. The influence of machine parameters on the surface roughness and cutting artifacts in the contour cut is discussed. It has been identified that the critical parameter in improving the surface finish is the spark pulse duration. A typical cutting artifact and its impact on measured stress values have been identified and demonstrated for a contour cut in a welded marine steel. A procedure is presented to correct contour displacement data from the influence of WEDM cutting artifacts, and is demonstrated on the correction of a measured weld residual stress. The corrected contour method improved the residual stress magnitude up to 150 MPa. The corrected contour method results were validated by X-ray diffraction, incremental center hole drilling, and neutron diffraction.

  14. Bearing Abilities and Progressive Damage Analysis of Three Dimensional Four-Directional Braided Composites with Cut-Edge

    NASA Astrophysics Data System (ADS)

    Lei, Bing; Liu, Zhenguo; Ya, Jixuan; Wang, Yibo; Li, Xiaokang

    2016-08-01

    Cut-edge is a kind of damage for the three-dimensional four-directional (3D4d) braided composites which is inevitable because of machining to meet requisite shape and working in the abominable environment. The longitudinal tensile experiment of the 3D4d braided composites with different braiding angles between cut-edge and the ones without cut-edge was conducted. Then representative volume cell (RVC) with interface zones was established to analyze the tensile properties through the fracture and damage mechanics. The periodic boundary conditions under the cut-edge and uncut-edge conditions were imposed to simulate the failure mechanism. Stress-strain distribution and the damage evolution nephogram in cut-edge condition were conducted. Numerical results were coincident with the experimental results. Finally the variation of cut-edge effect with the specimen thickness was simulated by superimposing inner cells. The consequence showed that thickness increase can effectively reduce cut-edge influence on longitudinal strength for 3D4d braided composites. Cut-edge simulation of braided composites has guiding significance on the actual engineering application.

  15. Transient response of Salix cuttings to changing water level regimes

    NASA Astrophysics Data System (ADS)

    Gorla, L.; Signarbieux, C.; Turberg, P.; Buttler, A.; Perona, P.

    2015-03-01

    Sustainable water management requires an understanding of the effects of flow regulation on riparian ecomorphological processes. We investigated the transient response of Salix viminalis by examining the effect of water-level regimes on its above-ground and below-ground biomass. Four sets of Salix cuttings, three juveniles (in the first growing season) and one mature (1 year old), were planted and initially grown under the same water-level regime for 1 month. We imposed three different water-level regime treatments representing natural variability, a seasonal trend with no peaks, and minimal flow (characteristic of hydropower) consisting of a constant water level and natural flood peaks. We measured sap flux, stem water potential, photosynthesis, growth parameters, and final root architecture. The mature cuttings were not affected by water table dynamics, but the juveniles displayed causal relationships between the changing water regime, plant growth, and root distribution during a 2 month transient period. For example, a 50% drop in mean sap flux corresponded with a -1.5 Mpa decrease in leaf water potential during the first day after the water regime was changed. In agreement with published field observations, the cuttings concentrated their roots close to the mean water table of the corresponding treatment, allowing survival under altered conditions and resilience to successive stress events. Juvenile development was strongly impacted by the minimum flow regime, leading to more than 60% reduction of both above-ground and below-ground biomass, with respect to the other treatments. Hence, we suggest avoiding minimum flow regimes where Salix restoration is prioritized.

  16. Underwater cutting technology of thick stainless steel with YAG laser

    NASA Astrophysics Data System (ADS)

    Chida, Itaru; Okazaki, Koki; Shima, Seishi; Kurihara, Kenji; Yuguchi, Yasuhiro; Sato, Ikuko

    2003-03-01

    In nuclear power plants, irradiated materials like Control Rod (CR) should be stored underwater after service. Due to reducing the storage space, underwater cutting technology is expected. In this study, we developed underwater cutting technology of thick stainless steel with YAG laser in order to cut used CR. Preliminary tests were performed with flat plate test-pieces to optimize the cutting conditions. Due to creating a local dry area between nozzle and test-piece, high-pressure air was blown from the nozzle. Underwater laser cutting was carried out by laser irradiation power of 4 kW, changing the parameters of cutting speed, distance between the nozzle and test-piece, and thickness of the test-piece. We also investigated the wastes like dross and aerosols by laser cutting. Amount of dross was approximately 0.1 kg/m after cutting a 14 mm thick stainless steel plate, which is estimated to be less than other cutting method. Based on these results, we developed underwater cutting system of CR test-piece with YAG laser as a mock-up test. In the cutting torch, there was tracking system was introduced to keep the distance between the nozzle and the test-piece constant, and cutting monitor was also set-in to detect whether the test-piece was successfully cut or not. We have already tried to cut the CR test-piece with this facility and successfully cut in half.

  17. Stimulated Calcitonin Cut-Offs by Different Tests

    PubMed Central

    Fugazzola, Laura

    2013-01-01

    Medullary thyroid cancer can be highly aggressive, especially if the diagnosis is done in advanced stages. Early diagnosis is based on RET genetic testing, for familial forms, and on the routine measurement of calcitonin (Ct). Nevertheless, since false-positive results can be obtained with the basal measurement of Ct, a provocative test to evaluate stimulated Ct is often needed. Pentagastrin which has been widely used to stimulate basal Ct, especially in European countries, is now hardly available. Thus, the stimulation with calcium (Ca), used in the 1970s-1980s and then abandoned for around 30 years, has recently elicited more interest. In the past 3 years, studies in patients and normal controls have demonstrated that the stimulation with Ca (2.3-2.5 mg/kg of elemental Ca, corresponding to 25 mg/kg of Ca gluconate) is highly potent and accurate. Novel gender-related cut-offs have been proposed for the Ca test, though the analysis of additional large series is predicted to modify these preliminary data. Finally, Ca seems to be the test of choice to stimulate Ct for the diagnosis and follow-up of medullary thyroid cancer, also because it is widely available, has a low cost and it is associated with a low number and intensity of side effects. In the present review the different methods to stimulate Ct and the cut-offs for the identification of the hyperplastic/neoplastic transformation of the C cells will be reported and discussed. PMID:24783038

  18. Spanish health care cuts: penny wise and pound foolish?

    PubMed

    Gené-Badia, Joan; Gallo, Pedro; Hernández-Quevedo, Cristina; García-Armesto, Sandra

    2012-06-01

    The purpose of this paper is to convey the specific health care actions and policies undertaken by the Spanish government, as well as by regional governments, as a result of the economic crisis. Throughout the last two years we have witnessed a number of actions in areas such as human capital, activity and processes, outsourcing and investment that, poorly coordinated, have shaped the nature of financial cuts on public services. This paper discloses the size and magnitude of these actions, the main actors involved and the major consequences for the health sector, citizens and patients. We further argue that there are a number of factors which have been neglected in the discourse and in the actions undertaken. First, the crisis situation is not being used as an opportunity for major reforms in the health care system. Further, the lay public and professionals have remained as observers in the process, with little to no participation at any point. Moreover, there is a general perception that the solution to the Spanish situation is either the proposed health care cuts or an increase in cost sharing for services which neglects alternative and/or complementary measures. Finally, there is a complete absence of any scientific component in the discourse and in the policies proposed.

  19. Operation and maintenance cost-cutting

    SciTech Connect

    Hollingshead, T.W.

    1996-12-31

    This presentation by Timothy W. Hollingshead, Technical Services Manager, Pacific Gas and Electric, is about cutting costs in the Operation and Maintenance phase of geothermal energy production. The necessity of cost control, keeping workers well-trained and avoiding OSHA fines, taking advantages of new technologies, and establishing predictive maintenance programs are some of the issues discussed in this article.

  20. Colleges Protect Workers and Cut Elsewhere

    ERIC Educational Resources Information Center

    Blumenstyk, Goldie

    2009-01-01

    Most colleges have steered through the first jolts of the recession without resorting to layoffs, cutting employee benefits, or imposing across-the-board freezes on hiring. But the economic pain is afflicting campuses in many other ways, according to the findings from a new survey of chief business officers conducted last month by "The Chronicle"…