FPGA/NIOS Implementation of an Adaptive FIR Filter Using Linear Prediction to Reduce Narrow-Band RFI for Radio Detection of Cosmic Rays

NASA Astrophysics Data System (ADS)

Szadkowski, Zbigniew; Fraenkel, E. D.; van den Berg, Ad M.

2013-10-01

We present the FPGA/NIOS implementation of an adaptive finite impulse response (FIR) filter based on linear prediction to suppress radio frequency interference (RFI). This technique will be used for experiments that observe coherent radio emission from extensive air showers induced by ultra-high-energy cosmic rays. These experiments are designed to make a detailed study of the development of the electromagnetic part of air showers. Therefore, these radio signals provide information that is complementary to that obtained by water-Cherenkov detectors which are predominantly sensitive to the particle content of an air shower at ground. The radio signals from air showers are caused by the coherent emission due to geomagnetic and charge-excess processes. These emissions can be observed in the frequency band between 10-100 MHz. However, this frequency range is significantly contaminated by narrow-band RFI and other human-made distortions. A FIR filter implemented in the FPGA logic segment of the front-end electronics of a radio sensor significantly improves the signal-to-noise ratio. In this paper we discuss an adaptive filter which is based on linear prediction. The coefficients for the linear predictor (LP) are dynamically refreshed and calculated in the embedded NIOS processor, which is implemented in the same FPGA chip. The Levinson recursion, used to obtain the filter coefficients, is also implemented in the NIOS and is partially supported by direct multiplication in the DSP blocks of the logic FPGA segment. Tests confirm that the LP can be an alternative to other methods involving multiple time-to-frequency domain conversions using an FFT procedure. These multiple conversions draw heavily on the power consumption of the FPGA and are avoided by the linear prediction approach. Minimization of the power consumption is an important issue because the final system will be powered by solar panels. The FIR filter has been successfully tested in the Altera development kits with the EP4CE115F29C7 from the Cyclone IV family and the EP3C120F780C7 from the Cyclone III family at a 170 MHz sampling rate, a 12-bit I/O resolution, and an internal 30-bit dynamic range. Most of the slow floating-point NIOS calculations have been moved to the FPGA logic segments as extended fixed-point operations, which significantly reduced the refreshing time of the coefficients used in the LP. We conclude that the LP is a viable alternative to other methods such as non-adaptive methods involving digital notch filters or multiple time-to-frequency domain conversions using an FFT procedure.

Adaptive linear predictor FIR filter based on the Cyclone V FPGA with HPS to reduce narrow band RFI in AERA radio detection of cosmic rays

DOE Office of Scientific and Technical Information (OSTI.GOV)

Szadkowski, Zbigniew

We present the new approach to a filtering of radio frequency interferences (RFI) in the Auger Engineering Radio Array (AERA) which study the electromagnetic part of the Extensive Air Showers. The radio stations can observe radio signals caused by coherent emissions due to geomagnetic radiation and charge excess processes. AERA observes frequency band from 30 to 80 MHz. This range is highly contaminated by human-made RFI. In order to improve the signal to noise ratio RFI filters are used in AERA to suppress this contamination. The first kind of filter used by AERA was the Median one, based on themore » Fast Fourier Transform (FFT) technique. The second one, which is currently in use, is the infinite impulse response (IIR) notch filter. The proposed new filter is a finite impulse response (FIR) filter based on a linear prediction (LP). A periodic contamination hidden in a registered signal (digitized in the ADC) can be extracted and next subtracted to make signal cleaner. The FIR filter requires a calculation of n=32, 64 or even 128 coefficients (dependent on a required speed or accuracy) by solving of n linear equations with coefficients built from the covariance Toeplitz matrix. This matrix can be solved by the Levinson recursion, which is much faster than the Gauss procedure. The filter has been already tested in the real AERA radio stations on Argentinean pampas with a very successful results. The linear equations were solved either in the virtual soft-core NIOSR processor (implemented in the FPGA chip as a net of logic elements) or in the external Voipac PXA270M ARM processor. The NIOS processor is relatively slow (50 MHz internal clock), calculations performed in an external processor consume a significant amount of time for data exchange between the FPGA and the processor. Test showed a very good efficiency of the RFI suppression for stationary (long-term) contaminations. However, we observed a short-time contaminations, which could not be suppressed either by the IIR-notch filter or by the FIR filter based on the linear predictions. For the LP FIR filter the refreshment time of the filter coefficients was to long and filter did not keep up with the changes of a contamination structure, mainly due to a long calculation time in a slow processors. We propose to use the Cyclone V SE chip with embedded micro-controller operating with 925 MHz internal clock to significantly reduce a refreshment time of the FIR coefficients. The lab results are promising. (authors)« less

Design of efficient circularly symmetric two-dimensional variable digital FIR filters.

PubMed

Bindima, Thayyil; Elias, Elizabeth

2016-05-01

Circularly symmetric two-dimensional (2D) finite impulse response (FIR) filters find extensive use in image and medical applications, especially for isotropic filtering. Moreover, the design and implementation of 2D digital filters with variable fractional delay and variable magnitude responses without redesigning the filter has become a crucial topic of interest due to its significance in low-cost applications. Recently the design using fixed word length coefficients has gained importance due to the replacement of multipliers by shifters and adders, which reduces the hardware complexity. Among the various approaches to 2D design, transforming a one-dimensional (1D) filter to 2D by transformation, is reported to be an efficient technique. In this paper, 1D variable digital filters (VDFs) with tunable cut-off frequencies are designed using Farrow structure based interpolation approach, and the sub-filter coefficients in the Farrow structure are made multiplier-less using canonic signed digit (CSD) representation. The resulting performance degradation in the filters is overcome by using artificial bee colony (ABC) optimization. Finally, the optimized 1D VDFs are mapped to 2D using generalized McClellan transformation resulting in low complexity, circularly symmetric 2D VDFs with real-time tunability.

Design of efficient circularly symmetric two-dimensional variable digital FIR filters

PubMed Central

Bindima, Thayyil; Elias, Elizabeth

2016-01-01

Circularly symmetric two-dimensional (2D) finite impulse response (FIR) filters find extensive use in image and medical applications, especially for isotropic filtering. Moreover, the design and implementation of 2D digital filters with variable fractional delay and variable magnitude responses without redesigning the filter has become a crucial topic of interest due to its significance in low-cost applications. Recently the design using fixed word length coefficients has gained importance due to the replacement of multipliers by shifters and adders, which reduces the hardware complexity. Among the various approaches to 2D design, transforming a one-dimensional (1D) filter to 2D by transformation, is reported to be an efficient technique. In this paper, 1D variable digital filters (VDFs) with tunable cut-off frequencies are designed using Farrow structure based interpolation approach, and the sub-filter coefficients in the Farrow structure are made multiplier-less using canonic signed digit (CSD) representation. The resulting performance degradation in the filters is overcome by using artificial bee colony (ABC) optimization. Finally, the optimized 1D VDFs are mapped to 2D using generalized McClellan transformation resulting in low complexity, circularly symmetric 2D VDFs with real-time tunability. PMID:27222739

An Innovations-Based Noise Cancelling Technique on Inverse Kepstrum Whitening Filter and Adaptive FIR Filter in Beamforming Structure

PubMed Central

Jeong, Jinsoo

2011-01-01

This paper presents an acoustic noise cancelling technique using an inverse kepstrum system as an innovations-based whitening application for an adaptive finite impulse response (FIR) filter in beamforming structure. The inverse kepstrum method uses an innovations-whitened form from one acoustic path transfer function between a reference microphone sensor and a noise source so that the rear-end reference signal will then be a whitened sequence to a cascaded adaptive FIR filter in the beamforming structure. By using an inverse kepstrum filter as a whitening filter with the use of a delay filter, the cascaded adaptive FIR filter estimates only the numerator of the polynomial part from the ratio of overall combined transfer functions. The test results have shown that the adaptive FIR filter is more effective in beamforming structure than an adaptive noise cancelling (ANC) structure in terms of signal distortion in the desired signal and noise reduction in noise with nonminimum phase components. In addition, the inverse kepstrum method shows almost the same convergence level in estimate of noise statistics with the use of a smaller amount of adaptive FIR filter weights than the kepstrum method, hence it could provide better computational simplicity in processing. Furthermore, the rear-end inverse kepstrum method in beamforming structure has shown less signal distortion in the desired signal than the front-end kepstrum method and the front-end inverse kepstrum method in beamforming structure. PMID:22163987

FIR digital filter-based ZCDPLL for carrier recovery

NASA Astrophysics Data System (ADS)

Nasir, Qassim

2016-04-01

The objective of this work is to analyse the performance of the newly proposed two-tap FIR digital filter-based first-order zero-crossing digital phase-locked loop (ZCDPLL) in the absence or presence of additive white Gaussian noise (AWGN). The introduction of the two-tap FIR digital filter widens the lock range of a ZCDPLL and improves the loop's operation in the presence of AWGN. The FIR digital filter tap coefficients affect the loop convergence behaviour and appropriate selection of those gains should be taken into consideration. The new proposed loop has wider locking range and faster acquisition time and reduces the phase error variations in the presence of noise.

FIR Filter of DS-CDMA UWB Modem Transmitter

NASA Astrophysics Data System (ADS)

Kang, Kyu-Min; Cho, Sang-In; Won, Hui-Chul; Choi, Sang-Sung

This letter presents low-complexity digital pulse shaping filter structures of a direct sequence code division multiple access (DS-CDMA) ultra wide-band (UWB) modem transmitter with a ternary spreading code. The proposed finite impulse response (FIR) filter structures using a look-up table (LUT) have the effect of saving the amount of memory by about 50% to 80% in comparison to the conventional FIR filter structures, and consequently are suitable for a high-speed parallel data process.

Frequency domain FIR and IIR adaptive filters

NASA Technical Reports Server (NTRS)

Lynn, D. W.

1990-01-01

A discussion of the LMS adaptive filter relating to its convergence characteristics and the problems associated with disparate eigenvalues is presented. This is used to introduce the concept of proportional convergence. An approach is used to analyze the convergence characteristics of block frequency-domain adaptive filters. This leads to a development showing how the frequency-domain FIR adaptive filter is easily modified to provide proportional convergence. These ideas are extended to a block frequency-domain IIR adaptive filter and the idea of proportional convergence is applied. Experimental results illustrating proportional convergence in both FIR and IIR frequency-domain block adaptive filters is presented.

Boundary implications for frequency response of interval FIR and IIR filters

NASA Technical Reports Server (NTRS)

Bose, N. K.; Kim, K. D.

1991-01-01

It is shown that vertex implication results in parameter space apply to interval trigonometric polynomials. Subsequently, it is shown that the frequency responses of both interval FIR and IIR filters are bounded by the frequency responses of certain extreme filters. The results apply directly in the evaluation of properties of designed filters, especially because it is more realistic to bound the filter coefficients from above and below instead of determining those with infinite precision because of finite arithmetic effects. Illustrative examples are provided to show how the extreme filters might be easily derived in any specific interval FIR or IIR filter design problem.

Methodology for processing pressure traces used as inputs for combustion analyses in diesel engines

NASA Astrophysics Data System (ADS)

Rašić, Davor; Vihar, Rok; Žvar Baškovič, Urban; Katrašnik, Tomaž

2017-05-01

This study proposes a novel methodology for designing an optimum equiripple finite impulse response (FIR) filter for processing in-cylinder pressure traces of a diesel internal combustion engine, which serve as inputs for high-precision combustion analyses. The proposed automated workflow is based on an innovative approach of determining the transition band frequencies and optimum filter order. The methodology is based on discrete Fourier transform analysis, which is the first step to estimate the location of the pass-band and stop-band frequencies. The second step uses short-time Fourier transform analysis to refine the estimated aforementioned frequencies. These pass-band and stop-band frequencies are further used to determine the most appropriate FIR filter order. The most widely used existing methods for estimating the FIR filter order are not effective in suppressing the oscillations in the rate- of-heat-release (ROHR) trace, thus hindering the accuracy of combustion analyses. To address this problem, an innovative method for determining the order of an FIR filter is proposed in this study. This method is based on the minimization of the integral of normalized signal-to-noise differences between the stop-band frequency and the Nyquist frequency. Developed filters were validated using spectral analysis and calculation of the ROHR. The validation results showed that the filters designed using the proposed innovative method were superior compared with those using the existing methods for all analyzed cases. Highlights • Pressure traces of a diesel engine were processed by finite impulse response (FIR) filters with different orders • Transition band frequencies were determined with an innovative method based on discrete Fourier transform and short-time Fourier transform • Spectral analyses showed deficiencies of existing methods in determining the FIR filter order • A new method of determining the FIR filter order for processing pressure traces was proposed • The efficiency of the new method was demonstrated by spectral analyses and calculations of rate-of-heat-release traces

Integrating the ECG power-line interference removal methods with rule-based system.

PubMed

Kumaravel, N; Senthil, A; Sridhar, K S; Nithiyanandam, N

1995-01-01

The power-line frequency interference in electrocardiographic signals is eliminated to enhance the signal characteristics for diagnosis. The power-line frequency normally varies +/- 1.5 Hz from its standard value of 50 Hz. In the present work, the performances of the linear FIR filter, Wave digital filter (WDF) and adaptive filter for the power-line frequency variations from 48.5 to 51.5 Hz in steps of 0.5 Hz are studied. The advantage of the LMS adaptive filter in the removal of power-line frequency interference even if the frequency of interference varies by +/- 1.5 Hz from its normal value of 50 Hz over other fixed frequency filters is very well justified. A novel method of integrating rule-based system approach with linear FIR filter and also with Wave digital filter are proposed. The performances of Rule-based FIR filter and Rule-based Wave digital filter are compared with the LMS adaptive filter.

The Essential Complexity of Auditory Receptive Fields

PubMed Central

Thorson, Ivar L.; Liénard, Jean; David, Stephen V.

2015-01-01

Encoding properties of sensory neurons are commonly modeled using linear finite impulse response (FIR) filters. For the auditory system, the FIR filter is instantiated in the spectro-temporal receptive field (STRF), often in the framework of the generalized linear model. Despite widespread use of the FIR STRF, numerous formulations for linear filters are possible that require many fewer parameters, potentially permitting more efficient and accurate model estimates. To explore these alternative STRF architectures, we recorded single-unit neural activity from auditory cortex of awake ferrets during presentation of natural sound stimuli. We compared performance of > 1000 linear STRF architectures, evaluating their ability to predict neural responses to a novel natural stimulus. Many were able to outperform the FIR filter. Two basic constraints on the architecture lead to the improved performance: (1) factorization of the STRF matrix into a small number of spectral and temporal filters and (2) low-dimensional parameterization of the factorized filters. The best parameterized model was able to outperform the full FIR filter in both primary and secondary auditory cortex, despite requiring fewer than 30 parameters, about 10% of the number required by the FIR filter. After accounting for noise from finite data sampling, these STRFs were able to explain an average of 40% of A1 response variance. The simpler models permitted more straightforward interpretation of sensory tuning properties. They also showed greater benefit from incorporating nonlinear terms, such as short term plasticity, that provide theoretical advances over the linear model. Architectures that minimize parameter count while maintaining maximum predictive power provide insight into the essential degrees of freedom governing auditory cortical function. They also maximize statistical power available for characterizing additional nonlinear properties that limit current auditory models. PMID:26683490

Efficient and Accurate Optimal Linear Phase FIR Filter Design Using Opposition-Based Harmony Search Algorithm

PubMed Central

Saha, S. K.; Dutta, R.; Choudhury, R.; Kar, R.; Mandal, D.; Ghoshal, S. P.

2013-01-01

In this paper, opposition-based harmony search has been applied for the optimal design of linear phase FIR filters. RGA, PSO, and DE have also been adopted for the sake of comparison. The original harmony search algorithm is chosen as the parent one, and opposition-based approach is applied. During the initialization, randomly generated population of solutions is chosen, opposite solutions are also considered, and the fitter one is selected as a priori guess. In harmony memory, each such solution passes through memory consideration rule, pitch adjustment rule, and then opposition-based reinitialization generation jumping, which gives the optimum result corresponding to the least error fitness in multidimensional search space of FIR filter design. Incorporation of different control parameters in the basic HS algorithm results in the balancing of exploration and exploitation of search space. Low pass, high pass, band pass, and band stop FIR filters are designed with the proposed OHS and other aforementioned algorithms individually for comparative optimization performance. A comparison of simulation results reveals the optimization efficacy of the OHS over the other optimization techniques for the solution of the multimodal, nondifferentiable, nonlinear, and constrained FIR filter design problems. PMID:23844390

Efficient and accurate optimal linear phase FIR filter design using opposition-based harmony search algorithm.

PubMed

Saha, S K; Dutta, R; Choudhury, R; Kar, R; Mandal, D; Ghoshal, S P

2013-01-01

In this paper, opposition-based harmony search has been applied for the optimal design of linear phase FIR filters. RGA, PSO, and DE have also been adopted for the sake of comparison. The original harmony search algorithm is chosen as the parent one, and opposition-based approach is applied. During the initialization, randomly generated population of solutions is chosen, opposite solutions are also considered, and the fitter one is selected as a priori guess. In harmony memory, each such solution passes through memory consideration rule, pitch adjustment rule, and then opposition-based reinitialization generation jumping, which gives the optimum result corresponding to the least error fitness in multidimensional search space of FIR filter design. Incorporation of different control parameters in the basic HS algorithm results in the balancing of exploration and exploitation of search space. Low pass, high pass, band pass, and band stop FIR filters are designed with the proposed OHS and other aforementioned algorithms individually for comparative optimization performance. A comparison of simulation results reveals the optimization efficacy of the OHS over the other optimization techniques for the solution of the multimodal, nondifferentiable, nonlinear, and constrained FIR filter design problems.

Novel programmable microwave photonic filter with arbitrary filtering shape and linear phase.

PubMed

Zhu, Xiaoqi; Chen, Feiya; Peng, Huanfa; Chen, Zhangyuan

2017-04-17

We propose and demonstrate a novel optical frequency comb (OFC) based microwave photonic filter which is able to realize arbitrary filtering shape with linear phase response. The shape of filter response is software programmable using finite impulse response (FIR) filter design method. By shaping the OFC spectrum using a programmable waveshaper, we can realize designed amplitude of FIR taps. Positive and negative sign of FIR taps are achieved by balanced photo-detection. The double sideband (DSB) modulation and symmetric distribution of filter taps are used to maintain the linear phase condition. In the experiment, we realize a fully programmable filter in the range from DC to 13.88 GHz. Four basic types of filters (lowpass, highpass, bandpass and bandstop) with different bandwidths, cut-off frequencies and central frequencies are generated. Also a triple-passband filter is realized in our experiment. To the best of our knowledge, it is the first demonstration of a programmable multiple passband MPF with linear phase response. The experiment shows good agreement with the theoretical result.

The synergy between complex channel-specific FIR filter and spatial filter for single-trial EEG classification.

PubMed

Yu, Ke; Wang, Yue; Shen, Kaiquan; Li, Xiaoping

2013-01-01

The common spatial pattern analysis (CSP), a frequently utilized feature extraction method in brain-computer-interface applications, is believed to be time-invariant and sensitive to noises, mainly due to an inherent shortcoming of purely relying on spatial filtering. Therefore, temporal/spectral filtering which can be very effective to counteract the unfavorable influence of noises is usually used as a supplement. This work integrates the CSP spatial filters with complex channel-specific finite impulse response (FIR) filters in a natural and intuitive manner. Each hybrid spatial-FIR filter is of high-order, data-driven and is unique to its corresponding channel. They are derived by introducing multiple time delays and regularization into conventional CSP. The general framework of the method follows that of CSP but performs better, as proven in single-trial classification tasks like event-related potential detection and motor imagery.

An improved design method based on polyphase components for digital FIR filters

NASA Astrophysics Data System (ADS)

Kumar, A.; Kuldeep, B.; Singh, G. K.; Lee, Heung No

2017-11-01

This paper presents an efficient design of digital finite impulse response (FIR) filter, based on polyphase components and swarm optimisation techniques (SOTs). For this purpose, the design problem is formulated as mean square error between the actual response and ideal response in frequency domain using polyphase components of a prototype filter. To achieve more precise frequency response at some specified frequency, fractional derivative constraints (FDCs) have been applied, and optimal FDCs are computed using SOTs such as cuckoo search and modified cuckoo search algorithms. A comparative study of well-proved swarm optimisation, called particle swarm optimisation and artificial bee colony algorithm is made. The excellence of proposed method is evaluated using several important attributes of a filter. Comparative study evidences the excellence of proposed method for effective design of FIR filter.

Design optimisation of powers-of-two FIR filter using self-organising random immigrants GA

NASA Astrophysics Data System (ADS)

Chandra, Abhijit; Chattopadhyay, Sudipta

2015-01-01

In this communication, we propose a novel design strategy of multiplier-less low-pass finite impulse response (FIR) filter with the aid of a recent evolutionary optimisation technique, known as the self-organising random immigrants genetic algorithm. Individual impulse response coefficients of the proposed filter have been encoded as sum of signed powers-of-two. During the formulation of the cost function for the optimisation algorithm, both the frequency response characteristic and the hardware cost of the discrete coefficient FIR filter have been considered. The role of crossover probability of the optimisation technique has been evaluated on the overall performance of the proposed strategy. For this purpose, the convergence characteristic of the optimisation technique has been included in the simulation results. In our analysis, two design examples of different specifications have been taken into account. In order to substantiate the efficiency of our proposed structure, a number of state-of-the-art design strategies of multiplier-less FIR filter have also been included in this article for the purpose of comparison. Critical analysis of the result unambiguously establishes the usefulness of our proposed approach for the hardware efficient design of digital filter.

Suppression of ITI by array head reading and 2D-equalization

NASA Astrophysics Data System (ADS)

Nakamura, Y.; Suzuto, R.; Osawa, H.; Okamoto, Y.; Kanai, Y.; Muraoka, H.

2017-05-01

Two-dimensional magnetic recording (TDMR) by shingled magnetic recording (SMR) draws attention as a next generation technology to increase the recording density in hard disk drive (HDD). It is shown that the two-dimensional finite impulse response (2D-FIR) filter provides gain the reproducing waveforms from an array head with 3 readers in the TDMR under a specification of 4 Tbit/inch.2 We evaluate the effect of the intertrack interference (ITI) reduction by 2D-FIR using the correlation between the real FIR filter output and the partial response class-I (PR1) signal corresponding to recording sequence by the computer simulation. The results show that the 2D-FIR filter is effective to mitigate ITI and improves the signal-to-noise ratio at the discriminate point by about 0.6 dB.

Comparison between hybrid feedforward-feedback, feedforward, and feedback structures for active noise control of fMRI noise.

PubMed

Reddy, Rajiv M; Panahi, Issa M S

2008-01-01

The performance of FIR feedforward, IIR feedforward, FIR feedback, hybrid FIR feedforward--FIR feedback, and hybrid IIR feedforward - FIR feedback structures for active noise control (ANC) are compared for an fMRI noise application. The filtered-input normalized least squares (FxNLMS) algorithm is used to update the coefficients of the adaptive filters in all these structures. Realistic primary and secondary paths of an fMRI bore are used by estimating them on a half cylindrical acrylic bore of 0.76 m (D)x1.52 m (L). Detailed results of the performance of the ANC system are presented in the paper for each of these structures. We find that the IIR feedforward structure produces most of the performance improvement in the hybrid IIR feedforward - FIR feedback structure and adding the feedback structure becomes almost redundant in the case of fMRI noise.

Frequency-selective quantitation of short-echo time 1H magnetic resonance spectra

NASA Astrophysics Data System (ADS)

Poullet, Jean-Baptiste; Sima, Diana M.; Van Huffel, Sabine; Van Hecke, Paul

2007-06-01

Accurate and efficient filtering techniques are required to suppress large nuisance components present in short-echo time magnetic resonance (MR) spectra. This paper discusses two powerful filtering techniques used in long-echo time MR spectral quantitation, the maximum-phase FIR filter (MP-FIR) and the Hankel-Lanczos Singular Value Decomposition with Partial ReOrthogonalization (HLSVD-PRO), and shows that they can be applied to their more complex short-echo time spectral counterparts. Both filters are validated and compared through extensive simulations. Their properties are discussed. In particular, the capability of MP-FIR for dealing with macromolecular components is emphasized. Although this property does not make a large difference for long-echo time MR spectra, it can be important when quantifying short-echo time spectra.

Dichroic filters to protect milliwatt far-infrared detectors from megawatt ECRH radiation.

PubMed

Bertschinger, G; Endres, C P; Lewen, F; Oosterbeek, J W

2008-10-01

Dichroic filters have been used to shield effectively the far infrared (FIR) detectors at the interferometer/polarimeter on TEXTOR. The filters consist of metal foils with regular holes, the hole diameter, the mutual spacing and the thickness of the foils are chosen to transmit radiation at the design frequency with transmission >90%. The attenuation at the low frequency end of the bandpass filter is about 30 dB per octave, the high frequency transmission is between 20% and 40%. The filters have been used to block the stray radiation from the megawatt microwave heating beam to the detectors of the FIR interferometer, operating with power on the detector in the milliwatt range. If required, the low frequency attenuation can be still enhanced, without compromising the transmission in the passband. The FIR interferometer used for plasma density and position control is no longer disturbed by electromagnetic waves used for plasma heating.

Design of adaptive control systems by means of self-adjusting transversal filters

NASA Technical Reports Server (NTRS)

Merhav, S. J.

1986-01-01

The design of closed-loop adaptive control systems based on nonparametric identification was addressed. Implementation is by self-adjusting Least Mean Square (LMS) transversal filters. The design concept is Model Reference Adaptive Control (MRAC). Major issues are to preserve the linearity of the error equations of each LMS filter, and to prevent estimation bias that is due to process or measurement noise, thus providing necessary conditions for the convergence and stability of the control system. The controlled element is assumed to be asymptotically stable and minimum phase. Because of the nonparametric Finite Impulse Response (FIR) estimates provided by the LMS filters, a-priori information on the plant model is needed only in broad terms. Following a survey of control system configurations and filter design considerations, system implementation is shown here in Single Input Single Output (SISO) format which is readily extendable to multivariable forms. In extensive computer simulation studies the controlled element is represented by a second-order system with widely varying damping, natural frequency, and relative degree.

MO-DE-207A-07: Filtered Iterative Reconstruction (FIR) Via Proximal Forward-Backward Splitting: A Synergy of Analytical and Iterative Reconstruction Method for CT

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gao, H

Purpose: This work is to develop a general framework, namely filtered iterative reconstruction (FIR) method, to incorporate analytical reconstruction (AR) method into iterative reconstruction (IR) method, for enhanced CT image quality. Methods: FIR is formulated as a combination of filtered data fidelity and sparsity regularization, and then solved by proximal forward-backward splitting (PFBS) algorithm. As a result, the image reconstruction decouples data fidelity and image regularization with a two-step iterative scheme, during which an AR-projection step updates the filtered data fidelity term, while a denoising solver updates the sparsity regularization term. During the AR-projection step, the image is projected tomore » the data domain to form the data residual, and then reconstructed by certain AR to a residual image which is in turn weighted together with previous image iterate to form next image iterate. Since the eigenvalues of AR-projection operator are close to the unity, PFBS based FIR has a fast convergence. Results: The proposed FIR method is validated in the setting of circular cone-beam CT with AR being FDK and total-variation sparsity regularization, and has improved image quality from both AR and IR. For example, AIR has improved visual assessment and quantitative measurement in terms of both contrast and resolution, and reduced axial and half-fan artifacts. Conclusion: FIR is proposed to incorporate AR into IR, with an efficient image reconstruction algorithm based on PFBS. The CBCT results suggest that FIR synergizes AR and IR with improved image quality and reduced axial and half-fan artifacts. The authors was partially supported by the NSFC (#11405105), the 973 Program (#2015CB856000), and the Shanghai Pujiang Talent Program (#14PJ1404500).« less

Fine-scale structure in the far-infrared Milky-Way

NASA Technical Reports Server (NTRS)

Waller, William H.; Wall, William F.; Reach, William T.; Varosi, Frank; Ebert, Rick; Laughlin, Gaylin; Boulanger, Francois

1995-01-01

This final report summarizes the work performed and which falls into five broad categories: (1) generation of a new data product (mosaics of the far-infrared emission in the Milky Way); (2) acquisition of associated data products at other wavelengths; (3) spatial filtering of the far-infrared mosaics and resulting images of the FIR fine-scale structure; (4) evaluation of the spatially filtered data; (5) characterization of the FIR fine-scale structure in terms of its spatial statistics; and (6) identification of interstellar counterparts to the FIR fine-scale structure.

An approach for fixed coefficient RNS-based FIR filter

NASA Astrophysics Data System (ADS)

Srinivasa Reddy, Kotha; Sahoo, Subhendu Kumar

2017-08-01

In this work, an efficient new modular multiplication method for {2k-1, 2k, 2k+1-1} moduli set is proposed to implement a residue number system (RNS)-based fixed coefficient finite impulse response filter. The new multiplication approach reduces the number of partial products by using pre-loaded product block. The reduction in partial products with the proposed modular multiplication improves the clock frequency and reduces the area and power as compared with the conventional modular multiplication. Further, the present approach eliminates a binary number to residue number converter circuit, which is usually needed at the front end of RNS-based system. In this work, two fixed coefficient filter architectures with the new modular multiplication approach are proposed. The filters are implemented using Verilog hardware description language. The United Microelectronics Corporation 90 nm technology library has been used for synthesis and the results area, power and delay are obtained with the help of Cadence register transfer level compiler. The power delay product (PDP) is also considered for performance comparison among the proposed filters. One of the proposed architecture is found to improve PDP gain by 60.83% as compared with the filter implemented with conventional modular multiplier. The filters functionality is validated with the help of Altera DSP Builder.

Adaptive filtering with the self-organizing map: a performance comparison.

PubMed

Barreto, Guilherme A; Souza, Luís Gustavo M

2006-01-01

In this paper we provide an in-depth evaluation of the SOM as a feasible tool for nonlinear adaptive filtering. A comprehensive survey of existing SOM-based and related architectures for learning input-output mappings is carried out and the application of these architectures to nonlinear adaptive filtering is formulated. Then, we introduce two simple procedures for building RBF-based nonlinear filters using the Vector-Quantized Temporal Associative Memory (VQTAM), a recently proposed method for learning dynamical input-output mappings using the SOM. The aforementioned SOM-based adaptive filters are compared with standard FIR/LMS and FIR/LMS-Newton linear transversal filters, as well as with powerful MLP-based filters in nonlinear channel equalization and inverse modeling tasks. The obtained results in both tasks indicate that SOM-based filters can consistently outperform powerful MLP-based ones.

A Comparative Analysis of Digital and Passive Filters for IFOC based Induction Motor Drive (EV) fed through ZSI

NASA Astrophysics Data System (ADS)

Bedi, Tarun; Heema, Dave; Singh, Dheerendra

2018-03-01

It is known that harmonics are generated in any power electronics based application. Since presence of harmonics is not desirable, it is necessary to remove the harmonics. The IFOC is based on stator current regulation, and the stator currents are sensed and used in the speed control algorithm. The current needs to be free from noise and harmonics for accurate further processing. In this paper, a passive analog filter, as well as a 50th order FIR filter is designed in MATLAB and implemented in Code Composer Studio to remove noise and distortion, and a comparative analysis has been done, for the speed control of an induction motor fed through ZSI, for electric vehicle application.

Adaptive clutter rejection filters for airborne Doppler weather radar applied to the detection of low altitude windshear

NASA Technical Reports Server (NTRS)

Keel, Byron M.

1989-01-01

An optimum adaptive clutter rejection filter for use with airborne Doppler weather radar is presented. The radar system is being designed to operate at low-altitudes for the detection of windshear in an airport terminal area where ground clutter returns may mask the weather return. The coefficients of the adaptive clutter rejection filter are obtained using a complex form of a square root normalized recursive least squares lattice estimation algorithm which models the clutter return data as an autoregressive process. The normalized lattice structure implementation of the adaptive modeling process for determining the filter coefficients assures that the resulting coefficients will yield a stable filter and offers possible fixed point implementation. A 10th order FIR clutter rejection filter indexed by geographical location is designed through autoregressive modeling of simulated clutter data. Filtered data, containing simulated dry microburst and clutter return, are analyzed using pulse-pair estimation techniques. To measure the ability of the clutter rejection filters to remove the clutter, results are compared to pulse-pair estimates of windspeed within a simulated dry microburst without clutter. In the filter evaluation process, post-filtered pulse-pair width estimates and power levels are also used to measure the effectiveness of the filters. The results support the use of an adaptive clutter rejection filter for reducing the clutter induced bias in pulse-pair estimates of windspeed.

A new method for fabrication of diamond-dust blocking filters

NASA Technical Reports Server (NTRS)

Collard, H. R.; Hogan, R. C.

1986-01-01

Thermal embedding of diamond dust onto a polyethylene-coated Al plate has been used to make a blocking filter for FIR applications. The Al plate is sandwiched between two Mylar 'blankets' and the air between the layers is removed by means of a small vacuum pump. After the polyethylene is heated and softened, the diamond dust is applied to the polyethylene coating using a brush. The optimum diamond dust grain sizes corresponding to polyethylene layer thicknesses of 9-12 microns are given in a table, and the application of the blocking filter to spectrometric measurements in the FIR is described. An exploded view diagram of the layered structure of the blocking filter is provided.

Seedling Responses of Five Species of Western Conifers to Simulated Ambient Sulfur Dioxide Exposures

Treesearch

Theodor D. Leininger; Paul R. Miller; Susan L. Schilling; Paul H. Dunn

1991-01-01

Seedlings of ponderosa pine, Douglas-fir, white fir, Engelmann spruce, and subalpine fir were exposed continuously to charcoal-filtered (CF) air or one of three levels of a simulated ambient exposure typical of SO, pollution near smelters in the western United States. Seedlings were exposed during winter-spring experiments for 60 days to hourly means of 17, 38, and 54...

Low power adder based auditory filter architecture.

PubMed

Rahiman, P F Khaleelur; Jayanthi, V S

2014-01-01

Cochlea devices are powered up with the help of batteries and they should possess long working life to avoid replacing of devices at regular interval of years. Hence the devices with low power consumptions are required. In cochlea devices there are numerous filters, each responsible for frequency variant signals, which helps in identifying speech signals of different audible range. In this paper, multiplierless lookup table (LUT) based auditory filter is implemented. Power aware adder architectures are utilized to add the output samples of the LUT, available at every clock cycle. The design is developed and modeled using Verilog HDL, simulated using Mentor Graphics Model-Sim Simulator, and synthesized using Synopsys Design Compiler tool. The design was mapped to TSMC 65 nm technological node. The standard ASIC design methodology has been adapted to carry out the power analysis. The proposed FIR filter architecture has reduced the leakage power by 15% and increased its performance by 2.76%.

Cat Swarm Optimization algorithm for optimal linear phase FIR filter design.

PubMed

Saha, Suman Kumar; Ghoshal, Sakti Prasad; Kar, Rajib; Mandal, Durbadal

2013-11-01

In this paper a new meta-heuristic search method, called Cat Swarm Optimization (CSO) algorithm is applied to determine the best optimal impulse response coefficients of FIR low pass, high pass, band pass and band stop filters, trying to meet the respective ideal frequency response characteristics. CSO is generated by observing the behaviour of cats and composed of two sub-models. In CSO, one can decide how many cats are used in the iteration. Every cat has its' own position composed of M dimensions, velocities for each dimension, a fitness value which represents the accommodation of the cat to the fitness function, and a flag to identify whether the cat is in seeking mode or tracing mode. The final solution would be the best position of one of the cats. CSO keeps the best solution until it reaches the end of the iteration. The results of the proposed CSO based approach have been compared to those of other well-known optimization methods such as Real Coded Genetic Algorithm (RGA), standard Particle Swarm Optimization (PSO) and Differential Evolution (DE). The CSO based results confirm the superiority of the proposed CSO for solving FIR filter design problems. The performances of the CSO based designed FIR filters have proven to be superior as compared to those obtained by RGA, conventional PSO and DE. The simulation results also demonstrate that the CSO is the best optimizer among other relevant techniques, not only in the convergence speed but also in the optimal performances of the designed filters. Copyright © 2013 ISA. Published by Elsevier Ltd. All rights reserved.

Fast digital zooming system using directionally adaptive image interpolation and restoration.

PubMed

Kang, Wonseok; Jeon, Jaehwan; Yu, Soohwan; Paik, Joonki

2014-01-01

This paper presents a fast digital zooming system for mobile consumer cameras using directionally adaptive image interpolation and restoration methods. The proposed interpolation algorithm performs edge refinement along the initially estimated edge orientation using directionally steerable filters. Either the directionally weighted linear or adaptive cubic-spline interpolation filter is then selectively used according to the refined edge orientation for removing jagged artifacts in the slanted edge region. A novel image restoration algorithm is also presented for removing blurring artifacts caused by the linear or cubic-spline interpolation using the directionally adaptive truncated constrained least squares (TCLS) filter. Both proposed steerable filter-based interpolation and the TCLS-based restoration filters have a finite impulse response (FIR) structure for real time processing in an image signal processing (ISP) chain. Experimental results show that the proposed digital zooming system provides high-quality magnified images with FIR filter-based fast computational structure.

FPGA-based fused smart sensor for dynamic and vibration parameter extraction in industrial robot links.

PubMed

Rodriguez-Donate, Carlos; Morales-Velazquez, Luis; Osornio-Rios, Roque Alfredo; Herrera-Ruiz, Gilberto; de Jesus Romero-Troncoso, Rene

2010-01-01

Intelligent robotics demands the integration of smart sensors that allow the controller to efficiently measure physical quantities. Industrial manipulator robots require a constant monitoring of several parameters such as motion dynamics, inclination, and vibration. This work presents a novel smart sensor to estimate motion dynamics, inclination, and vibration parameters on industrial manipulator robot links based on two primary sensors: an encoder and a triaxial accelerometer. The proposed smart sensor implements a new methodology based on an oversampling technique, averaging decimation filters, FIR filters, finite differences and linear interpolation to estimate the interest parameters, which are computed online utilizing digital hardware signal processing based on field programmable gate arrays (FPGA).

FPGA-Based Fused Smart Sensor for Dynamic and Vibration Parameter Extraction in Industrial Robot Links

PubMed Central

Rodriguez-Donate, Carlos; Morales-Velazquez, Luis; Osornio-Rios, Roque Alfredo; Herrera-Ruiz, Gilberto; de Jesus Romero-Troncoso, Rene

2010-01-01

Intelligent robotics demands the integration of smart sensors that allow the controller to efficiently measure physical quantities. Industrial manipulator robots require a constant monitoring of several parameters such as motion dynamics, inclination, and vibration. This work presents a novel smart sensor to estimate motion dynamics, inclination, and vibration parameters on industrial manipulator robot links based on two primary sensors: an encoder and a triaxial accelerometer. The proposed smart sensor implements a new methodology based on an oversampling technique, averaging decimation filters, FIR filters, finite differences and linear interpolation to estimate the interest parameters, which are computed online utilizing digital hardware signal processing based on field programmable gate arrays (FPGA). PMID:22319345

Method and system for training dynamic nonlinear adaptive filters which have embedded memory

NASA Technical Reports Server (NTRS)

Rabinowitz, Matthew (Inventor)

2002-01-01

Described herein is a method and system for training nonlinear adaptive filters (or neural networks) which have embedded memory. Such memory can arise in a multi-layer finite impulse response (FIR) architecture, or an infinite impulse response (IIR) architecture. We focus on filter architectures with separate linear dynamic components and static nonlinear components. Such filters can be structured so as to restrict their degrees of computational freedom based on a priori knowledge about the dynamic operation to be emulated. The method is detailed for an FIR architecture which consists of linear FIR filters together with nonlinear generalized single layer subnets. For the IIR case, we extend the methodology to a general nonlinear architecture which uses feedback. For these dynamic architectures, we describe how one can apply optimization techniques which make updates closer to the Newton direction than those of a steepest descent method, such as backpropagation. We detail a novel adaptive modified Gauss-Newton optimization technique, which uses an adaptive learning rate to determine both the magnitude and direction of update steps. For a wide range of adaptive filtering applications, the new training algorithm converges faster and to a smaller value of cost than both steepest-descent methods such as backpropagation-through-time, and standard quasi-Newton methods. We apply the algorithm to modeling the inverse of a nonlinear dynamic tracking system 5, as well as a nonlinear amplifier 6.

Fast Image Restoration for Spatially Varying Defocus Blur of Imaging Sensor

PubMed Central

Cheong, Hejin; Chae, Eunjung; Lee, Eunsung; Jo, Gwanghyun; Paik, Joonki

2015-01-01

This paper presents a fast adaptive image restoration method for removing spatially varying out-of-focus blur of a general imaging sensor. After estimating the parameters of space-variant point-spread-function (PSF) using the derivative in each uniformly blurred region, the proposed method performs spatially adaptive image restoration by selecting the optimal restoration filter according to the estimated blur parameters. Each restoration filter is implemented in the form of a combination of multiple FIR filters, which guarantees the fast image restoration without the need of iterative or recursive processing. Experimental results show that the proposed method outperforms existing space-invariant restoration methods in the sense of both objective and subjective performance measures. The proposed algorithm can be employed to a wide area of image restoration applications, such as mobile imaging devices, robot vision, and satellite image processing. PMID:25569760

Extending the impulse response in order to reduce errors due to impulse noise and signal fading

NASA Technical Reports Server (NTRS)

Webb, Joseph A.; Rolls, Andrew J.; Sirisena, H. R.

1988-01-01

A finite impulse response (FIR) digital smearing filter was designed to produce maximum intersymbol interference and maximum extension of the impulse response of the signal in a noiseless binary channel. A matched FIR desmearing filter at the receiver then reduced the intersymbol interference to zero. Signal fades were simulated by means of 100 percent signal blockage in the channel. Smearing and desmearing filters of length 256, 512, and 1024 were used for these simulations. Results indicate that impulse response extension by means of bit smearing appears to be a useful technique for correcting errors due to impulse noise or signal fading in a binary channel.

Design and implementation of a multiband digital filter using FPGA to extract the ECG signal in the presence of different interference signals.

PubMed

Aboutabikh, Kamal; Aboukerdah, Nader

2015-07-01

In this paper, we propose a practical way to synthesize and filter an ECG signal in the presence of four types of interference signals: (1) those arising from power networks with a fundamental frequency of 50Hz, (2) those arising from respiration, having a frequency range from 0.05 to 0.5Hz, (3) muscle signals with a frequency of 25Hz, and (4) white noise present within the ECG signal band. This was done by implementing a multiband digital filter (seven bands) of type FIR Multiband Least Squares using a digital programmable device (Cyclone II EP2C70F896C6 FPGA, Altera), which was placed on an education and development board (DE2-70, Terasic). This filter was designed using the VHDL language in the Quartus II 9.1 design environment. The proposed method depends on Direct Digital Frequency Synthesizers (DDFS) designed to synthesize the ECG signal and various interference signals. So that the synthetic ECG specifications would be closer to actual ECG signals after filtering, we designed in a single multiband digital filter instead of using three separate digital filters LPF, HPF, BSF. Thus all interference signals were removed with a single digital filter. The multiband digital filter results were studied using a digital oscilloscope to characterize input and output signals in the presence of differing sinusoidal interference signals and white noise. Copyright © 2015 Elsevier Ltd. All rights reserved.

A novel low-complexity digital filter design for wearable ECG devices

PubMed Central

Mehrnia, Alireza

2017-01-01

Wearable and implantable Electrocardiograph (ECG) devices are becoming prevailing tools for continuous real-time personal health monitoring. The ECG signal can be contaminated by various types of noise and artifacts (e.g., powerline interference, baseline wandering) that must be removed or suppressed for accurate ECG signal processing. Limited device size, power consumption and cost are critical issues that need to be carefully considered when designing any portable health monitoring device, including a battery-powered ECG device. This work presents a novel low-complexity noise suppression reconfigurable finite impulse response (FIR) filter structure for wearable ECG and heart monitoring devices. The design relies on a recently introduced optimally-factored FIR filter method. The new filter structure and several of its useful features are presented in detail. We also studied the hardware complexity of the proposed structure and compared it with the state-of-the-art. The results showed that the new ECG filter has a lower hardware complexity relative to the state-of-the-art ECG filters. PMID:28384272

A novel low-complexity digital filter design for wearable ECG devices.

PubMed

Asgari, Shadnaz; Mehrnia, Alireza

2017-01-01

Wearable and implantable Electrocardiograph (ECG) devices are becoming prevailing tools for continuous real-time personal health monitoring. The ECG signal can be contaminated by various types of noise and artifacts (e.g., powerline interference, baseline wandering) that must be removed or suppressed for accurate ECG signal processing. Limited device size, power consumption and cost are critical issues that need to be carefully considered when designing any portable health monitoring device, including a battery-powered ECG device. This work presents a novel low-complexity noise suppression reconfigurable finite impulse response (FIR) filter structure for wearable ECG and heart monitoring devices. The design relies on a recently introduced optimally-factored FIR filter method. The new filter structure and several of its useful features are presented in detail. We also studied the hardware complexity of the proposed structure and compared it with the state-of-the-art. The results showed that the new ECG filter has a lower hardware complexity relative to the state-of-the-art ECG filters.

Harmonised information exchange between decentralised food composition database systems.

PubMed

Pakkala, H; Christensen, T; de Victoria, I Martínez; Presser, K; Kadvan, A

2010-11-01

The main aim of the European Food Information Resource (EuroFIR) project is to develop and disseminate a comprehensive, coherent and validated data bank for the distribution of food composition data (FCD). This can only be accomplished by harmonising food description and data documentation and by the use of standardised thesauri. The data bank is implemented through a network of local FCD storages (usually national) under the control and responsibility of the local (national) EuroFIR partner. The implementation of the system based on the EuroFIR specifications is under development. The data interchange happens through the EuroFIR Web Services interface, allowing the partners to implement their system using methods and software suitable for the local computer environment. The implementation uses common international standards, such as Simple Object Access Protocol, Web Service Description Language and Extensible Markup Language (XML). A specifically constructed EuroFIR search facility (eSearch) was designed for end users. The EuroFIR eSearch facility compiles queries using a specifically designed Food Data Query Language and sends a request to those network nodes linked to the EuroFIR Web Services that will most likely have the requested information. The retrieved FCD are compiled into a specifically designed data interchange format (the EuroFIR Food Data Transport Package) in XML, which is sent back to the EuroFIR eSearch facility as the query response. The same request-response operation happens in all the nodes that have been selected in the EuroFIR eSearch facility for a certain task. Finally, the FCD are combined by the EuroFIR eSearch facility and delivered to the food compiler. The implementation of FCD interchange using decentralised computer systems instead of traditional data-centre models has several advantages. First of all, the local partners have more control over their FCD, which will increase commitment and improve quality. Second, a multicentred solution is more economically viable than the creation of a centralised data bank, because of the lack of national political support for multinational systems.

Optimal design of a bank of spatio-temporal filters for EEG signal classification.

PubMed

Higashi, Hiroshi; Tanaka, Toshihisa

2011-01-01

The spatial weights for electrodes called common spatial pattern (CSP) are known to be effective in EEG signal classification for motor imagery based brain computer interfaces (MI-BCI). To achieve accurate classification in CSP, the frequency filter should be properly designed. To this end, several methods for designing the filter have been proposed. However, the existing methods cannot consider plural brain activities described with different frequency bands and different spatial patterns such as activities of mu and beta rhythms. In order to efficiently extract these brain activities, we propose a method to design plural filters and spatial weights which extract desired brain activity. The proposed method designs finite impulse response (FIR) filters and the associated spatial weights by optimization of an objective function which is a natural extension of CSP. Moreover, we show by a classification experiment that the bank of FIR filters which are designed by introducing an orthogonality into the objective function can extract good discriminative features. Moreover, the experiment result suggests that the proposed method can automatically detect and extract brain activities related to motor imagery.

An optimization of the FPGA/NIOS adaptive FIR filter using linear prediction to reduce narrow band RFI for the next generation ground-based ultra-high energy cosmic-ray experiment

NASA Astrophysics Data System (ADS)

Szadkowski, Zbigniew; Fraenkel, E. D.; Glas, Dariusz; Legumina, Remigiusz

2013-12-01

The electromagnetic part of an extensive air shower developing in the atmosphere provides significant information complementary to that obtained by water Cherenkov detectors which are predominantly sensitive to the muonic content of an air shower at ground. The emissions can be observed in the frequency band between 10 and 100 MHz. However, this frequency range is significantly contaminated by narrow-band RFI and other human-made distortions. The Auger Engineering Radio Array currently suppresses the RFI by multiple time-to-frequency domain conversions using an FFT procedure as well as by a set of manually chosen IIR notch filters in the time-domain. An alternative approach developed in this paper is an adaptive FIR filter based on linear prediction (LP). The coefficients for the linear predictor are dynamically refreshed and calculated in the virtual NIOS processor. The radio detector is an autonomous system installed on the Argentinean pampas and supplied from a solar panel. Powerful calculation capacity inside the FPGA is a factor. Power consumption versus the degree of effectiveness of the calculation inside the FPGA is a figure of merit to be minimized. Results show that the RFI contamination can be significantly suppressed by the LP FIR filter for 64 or less stages.

Instantaneous and Frequency-Warped Signal Processing Techniques for Auditory Source Separation.

NASA Astrophysics Data System (ADS)

Wang, Avery Li-Chun

This thesis summarizes several contributions to the areas of signal processing and auditory source separation. The philosophy of Frequency-Warped Signal Processing is introduced as a means for separating the AM and FM contributions to the bandwidth of a complex-valued, frequency-varying sinusoid p (n), transforming it into a signal with slowly-varying parameters. This transformation facilitates the removal of p (n) from an additive mixture while minimizing the amount of damage done to other signal components. The average winding rate of a complex-valued phasor is explored as an estimate of the instantaneous frequency. Theorems are provided showing the robustness of this measure. To implement frequency tracking, a Frequency-Locked Loop algorithm is introduced which uses the complex winding error to update its frequency estimate. The input signal is dynamically demodulated and filtered to extract the envelope. This envelope may then be remodulated to reconstruct the target partial, which may be subtracted from the original signal mixture to yield a new, quickly-adapting form of notch filtering. Enhancements to the basic tracker are made which, under certain conditions, attain the Cramer -Rao bound for the instantaneous frequency estimate. To improve tracking, the novel idea of Harmonic -Locked Loop tracking, using N harmonically constrained trackers, is introduced for tracking signals, such as voices and certain musical instruments. The estimated fundamental frequency is computed from a maximum-likelihood weighting of the N tracking estimates, making it highly robust. The result is that harmonic signals, such as voices, can be isolated from complex mixtures in the presence of other spectrally overlapping signals. Additionally, since phase information is preserved, the resynthesized harmonic signals may be removed from the original mixtures with relatively little damage to the residual signal. Finally, a new methodology is given for designing linear-phase FIR filters which require a small fraction of the computational power of conventional FIR implementations. This design strategy is based on truncated and stabilized IIR filters. These signal-processing methods have been applied to the problem of auditory source separation, resulting in voice separation from complex music that is significantly better than previous results at far lower computational cost.

Reception of Multiple Telemetry Signals via One Dish Antenna

NASA Technical Reports Server (NTRS)

Mukai, Ryan; Vilnrotter, Victor

2010-01-01

A microwave aeronautical-telemetry receiver system includes an antenna comprising a seven-element planar array of receiving feed horns centered at the focal point of a paraboloidal dish reflector that is nominally aimed at a single aircraft or at multiple aircraft flying in formation. Through digital processing of the signals received by the seven feed horns, the system implements a method of enhanced cancellation of interference, such that it becomes possible to receive telemetry signals in the same frequency channel simultaneously from either or both of two aircraft at slightly different angular positions within the field of view of the antenna, even in the presence of multipath propagation. The present system is an advanced version of the system described in Spatio- Temporal Equalizer for a Receiving-Antenna Feed Array NPO-43077, NASA Tech Briefs, Vol. 34, No. 2 (February 2010), page 32. To recapitulate: The radio-frequency telemetry signals received by the seven elements of the array are digitized, converted to complex baseband form, and sent to a spatio-temporal equalizer that consists mostly of a bank of seven adaptive finite-impulse-response (FIR) filters (one for each element in the array) plus a unit that sums the outputs of the filters. The combination of the spatial diversity of the feedhorn array and the temporal diversity of the filter bank affords better multipath suppression performance than is achievable by means of temporal equalization alone. The FIR filter bank adapts itself in real time to enable reception of telemetry at a low bit error rate, even in the presence of frequency-selective multipath propagation like that commonly found at flight-test ranges. The combination of the array and the filter bank makes it possible to constructively add multipath incoming signals to the corresponding directly arriving signals, thereby enabling reductions in telemetry bit-error rates.

Quasi interpolation with Voronoi splines.

PubMed

Mirzargar, Mahsa; Entezari, Alireza

2011-12-01

We present a quasi interpolation framework that attains the optimal approximation-order of Voronoi splines for reconstruction of volumetric data sampled on general lattices. The quasi interpolation framework of Voronoi splines provides an unbiased reconstruction method across various lattices. Therefore this framework allows us to analyze and contrast the sampling-theoretic performance of general lattices, using signal reconstruction, in an unbiased manner. Our quasi interpolation methodology is implemented as an efficient FIR filter that can be applied online or as a preprocessing step. We present visual and numerical experiments that demonstrate the improved accuracy of reconstruction across lattices, using the quasi interpolation framework. © 2011 IEEE

Vacuum collection of Douglas-fir pollen for supplemental mass pollinations.

Treesearch

D.L. Copes; N.C. Vance; W.K. Randall; A. Jasumback; R. Hallman

1991-01-01

An Aget Cyclone dust collector and peripheral equipment were fieldtested for use in vacuuming large quantities of pollen from 30- to 40-foot trees in a Douglas-fir seed orchard. The Cyclone machine (Model 20SN31P) operated without a vacuum bag or filter device, so no blockage or reduction in vacuum efficiency occurred when large volumes of pollen were collected....

Power Spectral Density and Hilbert Transform

DTIC Science & Technology

2016-12-01

Fourier transform, Hilbert transform, digital filter , SDR 16. SECURITY CLASSIFICATION OF: 17. LIMITATION OF ABSTRACT UU 18. NUMBER...terms. A very good approximation to the ideal Hilbert transform is a low-pass finite impulse response (FIR) filter . In Fig. 7, we show a real signal...220), converted to an analytic signal using a 255-tap Hilbert transform low-pass filter . For an ideal Hilbert

Dense grid sibling frames with linear phase filters

NASA Astrophysics Data System (ADS)

Abdelnour, Farras

2013-09-01

We introduce new 5-band dyadic sibling frames with dense time-frequency grid. Given a lowpass filter satisfying certain conditions, the remaining filters are obtained using spectral factorization. The analysis and synthesis filterbanks share the same lowpass and bandpass filters but have different and oversampled highpass filters. This leads to wavelets approximating shift-invariance. The filters are FIR, have linear phase, and the resulting wavelets have vanishing moments. The filters are designed using spectral factorization method. The proposed method leads to smooth limit functions with higher approximation order, and computationally stable filterbanks.

Research on signal processing of shock absorber test bench based on zero-phase filter

NASA Astrophysics Data System (ADS)

Wu, Yi; Ding, Guoqing

2017-10-01

The quality of force-displacement diagram is significant to help evaluate the performance of shock absorbers. Damping force sampling data is often interfered by Gauss white noise, 50Hz power interference and its harmonic wave during the process of testing; data de-noising has become the core problem of drawing true, accurate and real-time indicator diagram. The noise and interference can be filtered out through generic IIR or FIR low-pass filter, but addition phase lag of useful signal will be caused due to the inherent attribute of IIR and FIR filter. The paper uses FRR method to realize zero-phase digital filtering in a software way based on mutual cancellation of phase lag between the forward and reverse sequences after through the filter. High-frequency interference above 40Hz are filtered out completely and noise attenuation is more than -40dB, with no additional phase lag. The method is able to restore the true signal as far as possible. Theoretical simulation and practical test indicate high-frequency noises have been effectively inhibited in multiple typical speed cases, signal-to-noise ratio being greatly improved; the curve in indicator diagram has better smoothness and fidelity. The FRR algorithm has low computational complexity, fast running time, and can be easily transplanted in multiple platforms.

WE-D-204-02: Novel Method for Correcting Degradation of Sharpness of Liquid-Crystal Display Based On Modulation Transfer Function

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tokurei, S; Department of Radiology, Yamaguchi University Hospital, Ube, Yamaguchi; Morishita, J

2015-06-15

Purpose: To develop a method for improving sharpness of images reproduced on liquid-crystal displays (LCDs) by compensating for the degradation of modulation transfer function (MTF) of the LCD. Methods: The inherent MTF of a color LCD (display MTF) was measured using a commercially available color digital camera. The frequency responses necessary to compensate for the resolution property of the LCD were calculated from the inverses of the display MTFs in both the horizontal and vertical directions. In addition, the inverses of the display MTFs were combined with the response of the human eye. The finite impulse response (FIR) filters weremore » computed by taking the inverse Fourier transform of the frequency responses, and the effects of the FIR filtering on both the resolution and noise properties of the displayed images were verified by measuring the MTF and Wiener spectrum (WS), respectively. The FIR filtering was then applied to the representation of digital bone and chest radiographs. Results: The FIR filtering improved the MTF values by up to almost 1.0 or greater over the frequency range of interest, while it minimally increased the WS values. Combining the inverses of the display MTFs with the response of the human eye led to further refinement of the MTF. Our method was successfully and beneficially applied to the image interpretation of bone radiographs. The resolution enhancement of chest radiographs, which include larger scattered radiation than bone radiographs, was easily perceived by incorporating the response of the human eye. In addition, no artifacts were observed on the processed images. Conclusion: Our proposed method to compensate for the degradation of the resolution properties of LCDs has the potential to improve the observer performance of radiologists when reading digital radiographs. This work was supported in part by grant from EIZO Corporation.« less

Exact reconstruction analysis/synthesis filter banks with time-varying filters

NASA Technical Reports Server (NTRS)

Arrowood, J. L., Jr.; Smith, M. J. T.

1993-01-01

This paper examines some of the analysis/synthesis issues associated with FIR time-varying filter banks where the filter bank coefficients are allowed to change in response to the input signal. Several issues are identified as being important in order to realize performance gains from time-varying filter banks in image coding applications. These issues relate to the behavior of the filters as transition from one set of filter banks to another occurs. Lattice structure formulations for the time varying filter bank problem are introduced and discussed in terms of their properties and transition characteristics.

A 1-channel 3-band wide dynamic range compression chip for vibration transducer of implantable hearing aids.

PubMed

Kim, Dongwook; Seong, Kiwoong; Kim, Myoungnam; Cho, Jinho; Lee, Jyunghyun

2014-01-01

In this paper, a digital audio processing chip which uses a wide dynamic range compression (WDRC) algorithm is designed and implemented for implantable hearing aids system. The designed chip operates at a single voltage of 3.3V and drives a 16 bit parallel input and output at 32 kHz sample. The designed chip has 1-channel 3-band WDRC composed of a FIR filter bank, a level detector, and a compression part. To verify the performance of the designed chip, we measured the frequency separations of bands and compression gain control to reflect the hearing threshold level.

Clutter Mitigation in Echocardiography Using Sparse Signal Separation

PubMed Central

Yavneh, Irad

2015-01-01

In ultrasound imaging, clutter artifacts degrade images and may cause inaccurate diagnosis. In this paper, we apply a method called Morphological Component Analysis (MCA) for sparse signal separation with the objective of reducing such clutter artifacts. The MCA approach assumes that the two signals in the additive mix have each a sparse representation under some dictionary of atoms (a matrix), and separation is achieved by finding these sparse representations. In our work, an adaptive approach is used for learning the dictionary from the echo data. MCA is compared to Singular Value Filtering (SVF), a Principal Component Analysis- (PCA-) based filtering technique, and to a high-pass Finite Impulse Response (FIR) filter. Each filter is applied to a simulated hypoechoic lesion sequence, as well as experimental cardiac ultrasound data. MCA is demonstrated in both cases to outperform the FIR filter and obtain results comparable to the SVF method in terms of contrast-to-noise ratio (CNR). Furthermore, MCA shows a lower impact on tissue sections while removing the clutter artifacts. In experimental heart data, MCA obtains in our experiments clutter mitigation with an average CNR improvement of 1.33 dB. PMID:26199622

Heating of large format filters in sub-mm and fir space optics

NASA Astrophysics Data System (ADS)

Baccichet, N.; Savini, G.

2017-11-01

Most FIR and sub-mm space borne observatories use polymer-based quasi-optical elements like filters and lenses, due to their high transparency and low absorption in such wavelength ranges. Nevertheless, data from those missions have proven that thermal imbalances in the instrument (not caused by filters) can complicate the data analysis. Consequently, for future, higher precision instrumentation, further investigation is required on any thermal imbalances embedded in such polymer-based filters. Particularly, in this paper the heating of polymers when operating at cryogenic temperature in space will be studied. Such phenomenon is an important aspect of their functioning since the transient emission of unwanted thermal radiation may affect the scientific measurements. To assess this effect, a computer model was developed for polypropylene based filters and PTFE-based coatings. Specifically, a theoretical model of their thermal properties was created and used into a multi-physics simulation that accounts for conductive and radiative heating effects of large optical elements, the geometry of which was suggested by the large format array instruments designed for future space missions. It was found that in the simulated conditions, the filters temperature was characterized by a time-dependent behaviour, modulated by a small scale fluctuation. Moreover, it was noticed that thermalization was reached only when a low power input was present.

The discrete prolate spheroidal filter as a digital signal processing tool

NASA Technical Reports Server (NTRS)

Mathews, J. D.; Breakall, J. K.; Karawas, G. K.

1983-01-01

The discrete prolate spheriodall (DPS) filter is one of the glass of nonrecursive finite impulse response (FIR) filters. The DPS filter is superior to other filters in this class in that it has maximum energy concentration in the frequency passband and minimum ringing in the time domain. A mathematical development of the DPS filter properties is given, along with information required to construct the filter. The properties of this filter were compared with those of the more commonly used filters of the same class. Use of the DPS filter allows for particularly meaningful statements of data time/frequency resolution cell values. The filter forms an especially useful tool for digital signal processing.

An advanced real-time digital signal processing system for linear systems emulation, with special emphasis on network and acoustic response characterization

NASA Astrophysics Data System (ADS)

Gaydecki, Patrick; Fernandes, Bosco

2003-11-01

A fast digital signal processing (DSP) system is described that can perform real-time emulation of a wide variety of linear audio-bandwidth systems and networks, such as reverberant spaces, musical instrument bodies and very high order filter networks. The hardware design is based upon a Motorola DSP56309 operating at 110 million multiplication-accumulations per second and a dual-channel 24 bit codec with a maximum sampling frequency of 192 kHz. High level software has been developed to express complex vector frequency responses as both infinite impulse response (IIR) and finite impulse response (FIR) coefficients, in a form suitable for real-time convolution by the firmware installed in the DSP system memory. An algorithm has also been devised to express IIR filters as equivalent FIR structures, thereby obviating the potential instabilities associated with recursive equations and negating the traditional deficiencies of FIR filters respecting equivalent analogue designs. The speed and dynamic range of the system is such that, when sampling at 48 kHz, the frequency response can be specified to a spectral precision of 22 Hz when sampling at 10 kHz, this resolution increases to 0.9 Hz. Moreover, it is also possible to control the phase of any frequency band with a theoretical precision of 10-5 degrees in all cases. The system has been applied in the study of analogue filter networks, real-time Hilbert transformation, phase-shift systems and musical instrument body emulation, where it is providing valuable new insights into the understanding of psychoacoustic mechanisms.

Low-cost space-varying FIR filter architecture for computational imaging systems

NASA Astrophysics Data System (ADS)

Feng, Guotong; Shoaib, Mohammed; Schwartz, Edward L.; Dirk Robinson, M.

2010-01-01

Recent research demonstrates the advantage of designing electro-optical imaging systems by jointly optimizing the optical and digital subsystems. The optical systems designed using this joint approach intentionally introduce large and often space-varying optical aberrations that produce blurry optical images. Digital sharpening restores reduced contrast due to these intentional optical aberrations. Computational imaging systems designed in this fashion have several advantages including extended depth-of-field, lower system costs, and improved low-light performance. Currently, most consumer imaging systems lack the necessary computational resources to compensate for these optical systems with large aberrations in the digital processor. Hence, the exploitation of the advantages of the jointly designed computational imaging system requires low-complexity algorithms enabling space-varying sharpening. In this paper, we describe a low-cost algorithmic framework and associated hardware enabling the space-varying finite impulse response (FIR) sharpening required to restore largely aberrated optical images. Our framework leverages the space-varying properties of optical images formed using rotationally-symmetric optical lens elements. First, we describe an approach to leverage the rotational symmetry of the point spread function (PSF) about the optical axis allowing computational savings. Second, we employ a specially designed bank of sharpening filters tuned to the specific radial variation common to optical aberrations. We evaluate the computational efficiency and image quality achieved by using this low-cost space-varying FIR filter architecture.

A low-noise delta-sigma phase modulator for polar transmitters.

PubMed

Zhou, Bo

2014-01-01

A low-noise phase modulator, using finite-impulse-response (FIR) filtering embedded delta-sigma (ΔΣ) fractional-N phase-locked loop (PLL), is fabricated in 0.18 μ m CMOS for GSM/EDGE polar transmitters. A simplified digital compensation filter with inverse-FIR and -PLL features is proposed to trade off the transmitter noise and linearity. Experimental results show that the presented architecture performs RF phase modulation well with 20 mW power dissipation from 1.6 V supply and achieves the root-mean-square (rms) and peak phase errors of 4° and 8.5°, respectively. The measured and simulated phase noises of -104 dBc/Hz and -120 dBc/Hz at 400-kHz offset from 1.8-GHz carrier frequency are observed, respectively.

Wideband aperture array using RF channelizers and massively parallel digital 2D IIR filterbank

NASA Astrophysics Data System (ADS)

Sengupta, Arindam; Madanayake, Arjuna; Gómez-García, Roberto; Engeberg, Erik D.

2014-05-01

Wideband receive-mode beamforming applications in wireless location, electronically-scanned antennas for radar, RF sensing, microwave imaging and wireless communications require digital aperture arrays that offer a relatively constant far-field beam over several octaves of bandwidth. Several beamforming schemes including the well-known true time-delay and the phased array beamformers have been realized using either finite impulse response (FIR) or fast Fourier transform (FFT) digital filter-sum based techniques. These beamforming algorithms offer the desired selectivity at the cost of a high computational complexity and frequency-dependant far-field array patterns. A novel approach to receiver beamforming is the use of massively parallel 2-D infinite impulse response (IIR) fan filterbanks for the synthesis of relatively frequency independent RF beams at an order of magnitude lower multiplier complexity compared to FFT or FIR filter based conventional algorithms. The 2-D IIR filterbanks demand fast digital processing that can support several octaves of RF bandwidth, fast analog-to-digital converters (ADCs) for RF-to-bits type direct conversion of wideband antenna element signals. Fast digital implementation platforms that can realize high-precision recursive filter structures necessary for real-time beamforming, at RF radio bandwidths, are also desired. We propose a novel technique that combines a passive RF channelizer, multichannel ADC technology, and single-phase massively parallel 2-D IIR digital fan filterbanks, realized at low complexity using FPGA and/or ASIC technology. There exists native support for a larger bandwidth than the maximum clock frequency of the digital implementation technology. We also strive to achieve More-than-Moore throughput by processing a wideband RF signal having content with N-fold (B = N Fclk/2) bandwidth compared to the maximum clock frequency Fclk Hz of the digital VLSI platform under consideration. Such increase in bandwidth is achieved without use of polyphase signal processing or time-interleaved ADC methods. That is, all digital processors operate at the same Fclk clock frequency without phasing, while wideband operation is achieved by sub-sampling of narrower sub-bands at the the RF channelizer outputs.

Study of Interpolated Timing Recovery Phase-Locked Loop with Linearly Constrained Adaptive Prefilter for Higher-Density Optical Disc

NASA Astrophysics Data System (ADS)

Kajiwara, Yoshiyuki; Shiraishi, Junya; Kobayashi, Shoei; Yamagami, Tamotsu

2009-03-01

A digital phase-locked loop (PLL) with a linearly constrained adaptive filter (LCAF) has been studied for higher-linear-density optical discs. LCAF has been implemented before an interpolated timing recovery (ITR) PLL unit in order to improve the quality of phase error calculation by using an adaptively equalized partial response (PR) signal. Coefficient update of an asynchronous sampled adaptive FIR filter with a least-mean-square (LMS) algorithm has been constrained by a projection matrix in order to suppress the phase shift of the tap coefficients of the adaptive filter. We have developed projection matrices that are suitable for Blu-ray disc (BD) drive systems by numerical simulation. Results have shown the properties of the projection matrices. Then, we have designed the read channel system of the ITR PLL with an LCAF model on the FPGA board for experiments. Results have shown that the LCAF improves the tilt margins of 30 gigabytes (GB) recordable BD (BD-R) and 33 GB BD read-only memory (BD-ROM) with a sufficient LMS adaptation stability.

Implementation of kernels on the Maestro processor

NASA Astrophysics Data System (ADS)

Suh, Jinwoo; Kang, D. I. D.; Crago, S. P.

Currently, most microprocessors use multiple cores to increase performance while limiting power usage. Some processors use not just a few cores, but tens of cores or even 100 cores. One such many-core microprocessor is the Maestro processor, which is based on Tilera's TILE64 processor. The Maestro chip is a 49-core, general-purpose, radiation-hardened processor designed for space applications. The Maestro processor, unlike the TILE64, has a floating point unit (FPU) in each core for improved floating point performance. The Maestro processor runs at 342 MHz clock frequency. On the Maestro processor, we implemented several widely used kernels: matrix multiplication, vector add, FIR filter, and FFT. We measured and analyzed the performance of these kernels. The achieved performance was up to 5.7 GFLOPS, and the speedup compared to single tile was up to 49 using 49 tiles.

Multichannel spatial auditory display for speech communications

NASA Technical Reports Server (NTRS)

Begault, D. R.; Erbe, T.; Wenzel, E. M. (Principal Investigator)

1994-01-01

A spatial auditory display for multiple speech communications was developed at NASA/Ames Research Center. Input is spatialized by the use of simplified head-related transfer functions, adapted for FIR filtering on Motorola 56001 digital signal processors. Hardware and firmware design implementations are overviewed for the initial prototype developed for NASA-Kennedy Space Center. An adaptive staircase method was used to determine intelligibility levels of four-letter call signs used by launch personnel at NASA against diotic speech babble. Spatial positions at 30 degrees azimuth increments were evaluated. The results from eight subjects showed a maximum intelligibility improvement of about 6-7 dB when the signal was spatialized to 60 or 90 degrees azimuth positions.

Multi-channel spatial auditory display for speech communications

NASA Astrophysics Data System (ADS)

Begault, Durand; Erbe, Tom

1993-10-01

A spatial auditory display for multiple speech communications was developed at NASA-Ames Research Center. Input is spatialized by use of simplified head-related transfer functions, adapted for FIR filtering on Motorola 56001 digital signal processors. Hardware and firmware design implementations are overviewed for the initial prototype developed for NASA-Kennedy Space Center. An adaptive staircase method was used to determine intelligibility levels of four letter call signs used by launch personnel at NASA, against diotic speech babble. Spatial positions at 30 deg azimuth increments were evaluated. The results from eight subjects showed a maximal intelligibility improvement of about 6 to 7 dB when the signal was spatialized to 60 deg or 90 deg azimuth positions.

Multichannel spatial auditory display for speech communications.

PubMed

Begault, D R; Erbe, T

1994-10-01

A spatial auditory display for multiple speech communications was developed at NASA/Ames Research Center. Input is spatialized by the use of simplified head-related transfer functions, adapted for FIR filtering on Motorola 56001 digital signal processors. Hardware and firmware design implementations are overviewed for the initial prototype developed for NASA-Kennedy Space Center. An adaptive staircase method was used to determine intelligibility levels of four-letter call signs used by launch personnel at NASA against diotic speech babble. Spatial positions at 30 degrees azimuth increments were evaluated. The results from eight subjects showed a maximum intelligibility improvement of about 6-7 dB when the signal was spatialized to 60 or 90 degrees azimuth positions.

Multichannel Spatial Auditory Display for Speed Communications

NASA Technical Reports Server (NTRS)

Begault, Durand R.; Erbe, Tom

1994-01-01

A spatial auditory display for multiple speech communications was developed at NASA/Ames Research Center. Input is spatialized by the use of simplifiedhead-related transfer functions, adapted for FIR filtering on Motorola 56001 digital signal processors. Hardware and firmware design implementations are overviewed for the initial prototype developed for NASA-Kennedy Space Center. An adaptive staircase method was used to determine intelligibility levels of four-letter call signs used by launch personnel at NASA against diotic speech babble. Spatial positions at 30 degree azimuth increments were evaluated. The results from eight subjects showed a maximum intelligibility improvement of about 6-7 dB when the signal was spatialized to 60 or 90 degree azimuth positions.

Multi-channel spatial auditory display for speech communications

NASA Technical Reports Server (NTRS)

Begault, Durand; Erbe, Tom

1993-01-01

A spatial auditory display for multiple speech communications was developed at NASA-Ames Research Center. Input is spatialized by use of simplified head-related transfer functions, adapted for FIR filtering on Motorola 56001 digital signal processors. Hardware and firmware design implementations are overviewed for the initial prototype developed for NASA-Kennedy Space Center. An adaptive staircase method was used to determine intelligibility levels of four letter call signs used by launch personnel at NASA, against diotic speech babble. Spatial positions at 30 deg azimuth increments were evaluated. The results from eight subjects showed a maximal intelligibility improvement of about 6 to 7 dB when the signal was spatialized to 60 deg or 90 deg azimuth positions.

A 128-Tap Highly Tunable CMOS IF Finite Impulse Response Filter for Pulsed Radar Applications

DOE PAGES

Mincey, John Stephen; Su, Eric C.; Silva-Martinez, Jose; ...

2018-02-28

A configurable-bandwidth (BW) filter is presented in this paper for pulsed radar applications. Also, to eliminate dispersion effects in the received waveform, a finite impulse response (FIR) topology is proposed, which has a measured standard deviation of an in-band group delay of 11 ns that is primarily dominated by the inherent, fully predictable delay introduced by the sample-and-hold. The filter operates at an IF of 20 MHz, and is tunable in BW from 1.5 to 15 MHz, which makes it optimal to be used with varying pulse widths in the radar. Employing a total of 128 taps, the FIR filtermore » provides greater than 50-dB sharp attenuation in the stopband in order to minimize all out-of-band noise in the low signal-to-noise received radar signal. Fabricated in a 0.18-μm silicon on insulator CMOS process, the proposed filter consumes approximately 3.5 mW/tap with a 1.8-V supply. Finally, a 20-MHz two-tone measurement with 200-kHz tone separation shows IIP3 greater than 8.5 dBm.« less

Adaptive feedforward control of non-minimum phase structural systems

NASA Astrophysics Data System (ADS)

Vipperman, J. S.; Burdisso, R. A.

1995-06-01

Adaptive feedforward control algorithms have been effectively applied to stationary disturbance rejection. For structural systems, the ideal feedforward compensator is a recursive filter which is a function of the transfer functions between the disturbance and control inputs and the error sensor output. Unfortunately, most control configurations result in a non-minimum phase control path; even a collocated control actuator and error sensor will not necessarily produce a minimum phase control path in the discrete domain. Therefore, the common practice is to choose a suitable approximation of the ideal compensator. In particular, all-zero finite impulse response (FIR) filters are desirable because of their inherent stability for adaptive control approaches. However, for highly resonant systems, large order filters are required for broadband applications. In this work, a control configuration is investigated for controlling non-minimum phase lightly damped structural systems. The control approach uses low order FIR filters as feedforward compensators in a configuration that has one more control actuator than error sensors. The performance of the controller was experimentally evaluated on a simply supported plate under white noise excitation for a two-input, one-output (2I1O) system. The results show excellent error signal reduction, attesting to the effectiveness of the method.

A 128-Tap Highly Tunable CMOS IF Finite Impulse Response Filter for Pulsed Radar Applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mincey, John Stephen; Su, Eric C.; Silva-Martinez, Jose

A configurable-bandwidth (BW) filter is presented in this paper for pulsed radar applications. Also, to eliminate dispersion effects in the received waveform, a finite impulse response (FIR) topology is proposed, which has a measured standard deviation of an in-band group delay of 11 ns that is primarily dominated by the inherent, fully predictable delay introduced by the sample-and-hold. The filter operates at an IF of 20 MHz, and is tunable in BW from 1.5 to 15 MHz, which makes it optimal to be used with varying pulse widths in the radar. Employing a total of 128 taps, the FIR filtermore » provides greater than 50-dB sharp attenuation in the stopband in order to minimize all out-of-band noise in the low signal-to-noise received radar signal. Fabricated in a 0.18-μm silicon on insulator CMOS process, the proposed filter consumes approximately 3.5 mW/tap with a 1.8-V supply. Finally, a 20-MHz two-tone measurement with 200-kHz tone separation shows IIP3 greater than 8.5 dBm.« less

A Low-Noise Delta-Sigma Phase Modulator for Polar Transmitters

PubMed Central

Zhou, Bo

2014-01-01

A low-noise phase modulator, using finite-impulse-response (FIR) filtering embedded delta-sigma (ΔΣ) fractional-N phase-locked loop (PLL), is fabricated in 0.18 μm CMOS for GSM/EDGE polar transmitters. A simplified digital compensation filter with inverse-FIR and -PLL features is proposed to trade off the transmitter noise and linearity. Experimental results show that the presented architecture performs RF phase modulation well with 20 mW power dissipation from 1.6 V supply and achieves the root-mean-square (rms) and peak phase errors of 4° and 8.5°, respectively. The measured and simulated phase noises of −104 dBc/Hz and −120 dBc/Hz at 400-kHz offset from 1.8-GHz carrier frequency are observed, respectively. PMID:24719578

A minimax technique for time-domain design of preset digital equalizers using linear programming

NASA Technical Reports Server (NTRS)

Vaughn, G. L.; Houts, R. C.

1975-01-01

A linear programming technique is presented for the design of a preset finite-impulse response (FIR) digital filter to equalize the intersymbol interference (ISI) present in a baseband channel with known impulse response. A minimax technique is used which minimizes the maximum absolute error between the actual received waveform and a specified raised-cosine waveform. Transversal and frequency-sampling FIR digital filters are compared as to the accuracy of the approximation, the resultant ISI and the transmitted energy required. The transversal designs typically have slightly better waveform accuracy for a given distortion; however, the frequency-sampling equalizer uses fewer multipliers and requires less transmitted energy. A restricted transversal design is shown to use the least number of multipliers at the cost of a significant increase in energy and loss of waveform accuracy at the receiver.

Robust adaptive extended Kalman filtering for real time MR-thermometry guided HIFU interventions.

PubMed

Roujol, Sébastien; de Senneville, Baudouin Denis; Hey, Silke; Moonen, Chrit; Ries, Mario

2012-03-01

Real time magnetic resonance (MR) thermometry is gaining clinical importance for monitoring and guiding high intensity focused ultrasound (HIFU) ablations of tumorous tissue. The temperature information can be employed to adjust the position and the power of the HIFU system in real time and to determine the therapy endpoint. The requirement to resolve both physiological motion of mobile organs and the rapid temperature variations induced by state-of-the-art high-power HIFU systems require fast MRI-acquisition schemes, which are generally hampered by low signal-to-noise ratios (SNRs). This directly limits the precision of real time MR-thermometry and thus in many cases the feasibility of sophisticated control algorithms. To overcome these limitations, temporal filtering of the temperature has been suggested in the past, which has generally an adverse impact on the accuracy and latency of the filtered data. Here, we propose a novel filter that aims to improve the precision of MR-thermometry while monitoring and adapting its impact on the accuracy. For this, an adaptive extended Kalman filter using a model describing the heat transfer for acoustic heating in biological tissues was employed together with an additional outlier rejection to address the problem of sparse artifacted temperature points. The filter was compared to an efficient matched FIR filter and outperformed the latter in all tested cases. The filter was first evaluated on simulated data and provided in the worst case (with an approximate configuration of the model) a substantial improvement of the accuracy by a factor 3 and 15 during heat up and cool down periods, respectively. The robustness of the filter was then evaluated during HIFU experiments on a phantom and in vivo in porcine kidney. The presence of strong temperature artifacts did not affect the thermal dose measurement using our filter whereas a high measurement variation of 70% was observed with the FIR filter.

A multichannel nonlinear adaptive noise canceller based on generalized FLANN for fetal ECG extraction

NASA Astrophysics Data System (ADS)

Ma, Yaping; Xiao, Yegui; Wei, Guo; Sun, Jinwei

2016-01-01

In this paper, a multichannel nonlinear adaptive noise canceller (ANC) based on the generalized functional link artificial neural network (FLANN, GFLANN) is proposed for fetal electrocardiogram (FECG) extraction. A FIR filter and a GFLANN are equipped in parallel in each reference channel to respectively approximate the linearity and nonlinearity between the maternal ECG (MECG) and the composite abdominal ECG (AECG). A fast scheme is also introduced to reduce the computational cost of the FLANN and the GFLANN. Two (2) sets of ECG time sequences, one synthetic and one real, are utilized to demonstrate the improved effectiveness of the proposed nonlinear ANC. The real dataset is derived from the Physionet non-invasive FECG database (PNIFECGDB) including 55 multichannel recordings taken from a pregnant woman. It contains two subdatasets that consist of 14 and 8 recordings, respectively, with each recording being 90 s long. Simulation results based on these two datasets reveal, on the whole, that the proposed ANC does enjoy higher capability to deal with nonlinearity between MECG and AECG as compared with previous ANCs in terms of fetal QRS (FQRS)-related statistics and morphology of the extracted FECG waveforms. In particular, for the second real subdataset, the F1-measure results produced by the PCA-based template subtraction (TSpca) technique and six (6) single-reference channel ANCs using LMS- and RLS-based FIR filters, Volterra filter, FLANN, GFLANN, and adaptive echo state neural network (ESN a ) are 92.47%, 93.70%, 94.07%, 94.22%, 94.90%, 94.90%, and 95.46%, respectively. The same F1-measure statistical results from five (5) multi-reference channel ANCs (LMS- and RLS-based FIR filters, Volterra filter, FLANN, and GFLANN) for the second real subdataset turn out to be 94.08%, 94.29%, 94.68%, 94.91%, and 94.96%, respectively. These results indicate that the ESN a and GFLANN perform best, with the ESN a being slightly better than the GFLANN but about four times more computationally expensive than the GFLANN, which makes the GFLANN a good alternative for NI-FECG extraction.

Development of Software for a Lidar-Altimeter Processor

NASA Technical Reports Server (NTRS)

Rosenberg, Jacob S.; Trujillo, Carlos

2005-01-01

A report describes the development of software for a digital processor that operates in conjunction with a finite-impulse-response (FIR) chip in a spaceborne lidar altimeter. Processing is started by a laser-fire interrupt signal that is repeated at intervals of 25 ms. For the purpose of discriminating between returns from the ground and returns from such things as trees, buildings, and clouds, the software is required to scan digitized lidar-return data in reverse of the acquisition sequence in order to distinguish the last return pulse from within a commanded ground-return range window. The digitized waveform information within this range window is filtered through 6 matched filters, in the hardware electronics, in order to maximize the probability of finding echoes from sloped or rough terrain and minimize the probability of selecting cloud returns. From the data falling past the end of the range window, there is obtained a noise baseline that is used to calculate a threshold value for each filter. The data from each filter is analyzed by a complex weighting scheme and the filter with the greatest weight is selected. A region around the peak of the ground return pulse associated with the selected filter is placed in telemetry, as well as information on its location, height, and other characteristics. The software requires many uplinked parameters as input. Included in the report is a discussion of major software-development problems posed by the design of the FIR chip and the need for the software to complete its process within 20 ms to fit within the overall 25-ms cycle.

An active structural acoustic control approach for the reduction of the structure-borne road noise

NASA Astrophysics Data System (ADS)

Douville, Hugo; Berry, Alain; Masson, Patrice

2002-11-01

The reduction of the structure-borne road noise generated inside the cabin of an automobile is investigated using an Active Structural Acoustic Control (ASAC) approach. First, a laboratory test bench consisting of a wheel/suspension/lower suspension A-arm assembly has been developed in order to identify the vibroacoustic transfer paths (up to 250 Hz) for realistic road noise excitation of the wheel. Frequency Response Function (FRF) measurements between the excitation/control actuators and each suspension/chassis linkage are used to characterize the different transfer paths that transmit energy through the chassis of the car. Second, a FE/BE model (Finite/Boundary Elements) was developed to simulate the acoustic field of an automobile cab interior. This model is used to predict the acoustic field inside the cabin as a response to the measured forces applied on the suspension/chassis linkages. Finally, an experimental implementation of ASAC is presented. The control approach relies on the use of inertial actuators to modify the vibration behavior of the suspension and the automotive chassis such that its noise radiation efficiency is decreased. The implemented algorithm consists of a MIMO (Multiple-Input-Multiple-Output) feedforward configuration with a filtered-X LMS algorithm using an advanced reference signal (width FIR filters) using the Simulink/Dspace environment for control prototyping.

Analyses of Great Smoky Mountain Red Spruce Tree Ring Data

Treesearch

Paul C. van Deusen; [Editor

1988-01-01

Four different analyses of red spruce tree ring data from the Great Smoky Mountains are presented along with a description of the spruce/fir ecosystem.The analyses use several techniques including spatial analysis, fractals, spline detrending, and the Kalman filter.

Optimal design of FIR triplet halfband filter bank and application in image coding.

PubMed

Kha, H H; Tuan, H D; Nguyen, T Q

2011-02-01

This correspondence proposes an efficient semidefinite programming (SDP) method for the design of a class of linear phase finite impulse response triplet halfband filter banks whose filters have optimal frequency selectivity for a prescribed regularity order. The design problem is formulated as the minimization of the least square error subject to peak error constraints and regularity constraints. By using the linear matrix inequality characterization of the trigonometric semi-infinite constraints, it can then be exactly cast as a SDP problem with a small number of variables and, hence, can be solved efficiently. Several design examples of the triplet halfband filter bank are provided for illustration and comparison with previous works. Finally, the image coding performance of the filter bank is presented.

Landsat thematic mapper attitude data processing

NASA Technical Reports Server (NTRS)

Sehn, G. J.; Miller, S. F.

1984-01-01

The Landsat 4 and 5 satellites carry a new, high resolution, seven band thematic mapper imaging instrument. The spacecraft also carry two types of attitude sensors: a gyroscopic internal reference unit (IRU) which senses angular rate from dc to about 2 Hz, and an AC-coupled angular displacement sensor (ADS) measuring angular deviation above 2 Hz. A description of the derivation of the crossover network used to combine and equalize the IRU and ADS data is made. Also described are the digital data processing algorithms which produce the time history of the satellites' attitude motion including the finite impulse response (FIR) implementation of G and F filters; the resampling (interpolation/decimation) and synchronization of the IRU and ADS data; and the axis rotations required as a result of the on-board sensor locations on three orthogonal axes.

Two-Dimensional Signal Processing, Optical Information Storage and Processing, and Electromagnetic Measurements

DTIC Science & Technology

1994-05-16

analysis of anisotropic grating diffraction, perfor- mance analysis of Givens rotation integrated optical interdigitated-electrode cross- channel Bragg...11. T. R. Gardos and R. M. Mersereau, "FIR filtering on a lattice with periodically deleted samples," Proc. 1991 IEEE Int. Conf. on Acoustics...pp. vol. 1, pp. 301-311, July 1992. 23. T. R. Gardos , K. Nayebi, and R. M. Mersereau, "Time domain analysis of multi- dimensional multi-rate filter

Using recurrence plot analysis for software execution interpretation and fault detection

NASA Astrophysics Data System (ADS)

Mosdorf, M.

2015-09-01

This paper shows a method targeted at software execution interpretation and fault detection using recurrence plot analysis. In in the proposed approach recurrence plot analysis is applied to software execution trace that contains executed assembly instructions. Results of this analysis are subject to further processing with PCA (Principal Component Analysis) method that simplifies number coefficients used for software execution classification. This method was used for the analysis of five algorithms: Bubble Sort, Quick Sort, Median Filter, FIR, SHA-1. Results show that some of the collected traces could be easily assigned to particular algorithms (logs from Bubble Sort and FIR algorithms) while others are more difficult to distinguish.

A SSVEP Stimuli Encoding Method Using Trinary Frequency-Shift Keying Encoded SSVEP (TFSK-SSVEP).

PubMed

Zhao, Xing; Zhao, Dechun; Wang, Xia; Hou, Xiaorong

2017-01-01

SSVEP is a kind of BCI technology with advantage of high information transfer rate. However, due to its nature, frequencies could be used as stimuli are scarce. To solve such problem, a stimuli encoding method which encodes SSVEP signal using Frequency Shift-Keying (FSK) method is developed. In this method, each stimulus is controlled by a FSK signal which contains three different frequencies that represent "Bit 0," "Bit 1" and "Bit 2" respectively. Different to common BFSK in digital communication, "Bit 0" and "Bit 1" composited the unique identifier of stimuli in binary bit stream form, while "Bit 2" indicates the ending of a stimuli encoding. EEG signal is acquired on channel Oz, O1, O2, Pz, P3, and P4, using ADS1299 at the sample rate of 250 SPS. Before original EEG signal is quadrature demodulated, it is detrended and then band-pass filtered using FFT-based FIR filtering to remove interference. Valid peak of the processed signal is acquired by calculating its derivative and converted into bit stream using window method. Theoretically, this coding method could implement at least 2 n -1 ( n is the length of bit command) stimulus while keeping the ITR the same. This method is suitable to implement stimuli on a monitor and where the frequency and phase could be used to code stimuli is limited as well as implementing portable BCI devices which is not capable of performing complex calculations.

Evaluation and Analysis of a Multi-Band Transceiver for Next Generation Telemetry Applications

DTIC Science & Technology

2014-06-01

DDC ) BAND SELECTION Kintex FPGA DIGITAL RADIO RECEIVER DIGITAL RADIO TRANSMITTER ADC Fs < 225 MSPS Fs = 400 MHz RF BW = 36 MHz FREQ TRANSLATION VIA...MANAGER (MMCM) DIGITAL DOWN CONVERSION ( DDC ) BAND SELECTIVE FILTER Kintex FPGA DIGITAL RADIO RECEIVER DIGITAL RADIO TRANSMITTER FIR FINE TRANSLATION

Spatio-Temporal Equalizer for a Receiving-Antenna Feed Array

NASA Technical Reports Server (NTRS)

Mukai, Ryan; Lee, Dennis; Vilnrotter, Victor

2010-01-01

A spatio-temporal equalizer has been conceived as an improved means of suppressing multipath effects in the reception of aeronautical telemetry signals, and may be adaptable to radar and aeronautical communication applications as well. This equalizer would be an integral part of a system that would also include a seven-element planar array of receiving feed horns centered at the focal point of a paraboloidal antenna that would be nominally aimed at or near the aircraft that would be the source of the signal that one seeks to receive (see Figure 1). This spatio-temporal equalizer would consist mostly of a bank of seven adaptive finite-impulse-response (FIR) filters one for each element in the array - and the outputs of the filters would be summed (see Figure 2). The combination of the spatial diversity of the feedhorn array and the temporal diversity of the filter bank would afford better multipath-suppression performance than is achievable by means of temporal equalization alone. The seven-element feed array would supplant the single feed horn used in a conventional paraboloidal ground telemetry-receiving antenna. The radio-frequency telemetry signals re ceiv ed by the seven elements of the array would be digitized, converted to complex baseband form, and sent to the FIR filter bank, which would adapt itself in real time to enable reception of telemetry at a low bit error rate, even in the presence of multipath of the type found at many flight test ranges.

Characterizing root-associated fungal communities and soils of Douglas-fir (Pseudotsuga menziesii) stands that naturally produce Oregon white truffles (Tuber oregonense and Tuber gibbosum).

PubMed

Benucci, Gian Maria Niccolò; Lefevre, Charles; Bonito, Gregory

2016-07-01

Many truffle species in the genus Tuber are endemic to North America. Some of these have commercial value such as Tuber oregonense and Tuber gibbosum, commonly known as Oregon white truffles. Most of what is known about the ecology of these truffles comes from observational data. These truffle species form ectomycorrhizas with Douglas-fir (Pseudotsuga menziesii) and sometimes fruit abundantly in early successional forest regrowth. The goal of this study was to characterize fungal communities and soils associated with truffle-producing Douglas-fir sites. We extracted DNA from roots of five trees at four different truffle-producing Douglas-fir sites (n = 20). We amplified the internal transcribed spacer (ITS) region of the nuclear ribosomal DNA (nrDNA) and sequenced amplicons with 454 pyrosequencing. After quality filtering, we assembled 15,713 sequences into 150 fungal operational taxonomic units (OTUs). Pezizomycetes (Tuber and Pyronemataceae) were the most abundant taxa detected followed by Helotiales. Agaricomycetes represented most by Thelephoraceae, Russulaceae, and Inocybaceae were also abundant. A total of five Tuber species were detected. T. oregonense was the most abundant OTU, followed by T. gibbosum and Wilcoxina mikolae. Fungal root endophytes were also detected and well represented by Chalara and Phialocephala spp. Fungal community structure and soil chemistry differed between sites. This study represents the first characterization of the fungal communities in Douglas-fir stands producing Oregon white truffles. We found that Tuber species can be dominant ectomycorrhizal symbionts of Douglas-fir. Truffle fungi are also important in forest health, food webs, and as a non-timber forest resource that can contribute to rural economies.

Seed invasion filters and forest fire severity

Treesearch

Tom R. Cottrell; Paul F. Hessburg; Jonathan A. Betz

2008-01-01

Forest seed dispersal is altered after fire. Using seed traps, we studied impacts of fire severity on timing of seed dispersal, total seed rain, and seed rain richness in patches of high and low severity fire and unburned Douglas-fir (Pseudotsuga menziesii) forests in the Fischer and Tyee fire complexes in the eastern Washington Cascades. Unburned...

Next-Generation A/D Sampler ADS3000+ for VLBI2010

NASA Technical Reports Server (NTRS)

Takefuji, Kazuhiro; Takeuchi, Hiroshi; Tsutsumi, Masanori; Koyama, Yasuhiro

2010-01-01

A high-speed A/D sampler, called ADS3000+, has been developed in 2008, which can sample one analog signal up to 4 Gbps to versatile Linux PC. After A/D conversion, the ADS3000+ can perform digital signal processing such as real-time DBBC (Digital Base Band Conversion) and FIR filtering such as simple CW RFI filtering using the installed FPGAs. A 4 Gsps fringe test with the ADS3000+ has been successfully performed. The ADS3000+ will not exclusively be used for VLBI but will also be employed in other applications.

Compact Focal Plane Assembly for Planetary Science

NASA Technical Reports Server (NTRS)

Brown, Ari; Aslam, Shahid; Huang, Wei-Chung; Steptoe-Jackson, Rosalind

2013-01-01

A compact radiometric focal plane assembly (FPA) has been designed in which the filters are individually co-registered over compact thermopile pixels. This allows for construction of an ultralightweight and compact radiometric instrument. The FPA also incorporates micromachined baffles in order to mitigate crosstalk and low-pass filter windows in order to eliminate high-frequency radiation. Compact metal mesh bandpass filters were fabricated for the far infrared (FIR) spectral range (17 to 100 microns), a game-changing technology for future planetary FIR instruments. This fabrication approach allows the dimensions of individual metal mesh filters to be tailored with better than 10- micron precision. In contrast, conventional compact filters employed in recent missions and in near-term instruments consist of large filter sheets manually cut into much smaller pieces, which is a much less precise and much more labor-intensive, expensive, and difficult process. Filter performance was validated by integrating them with thermopile arrays. Demonstration of the FPA will require the integration of two technologies. The first technology is compact, lightweight, robust against cryogenic thermal cycling, and radiation-hard micromachined bandpass filters. They consist of a copper mesh supported on a deep reactive ion-etched silicon frame. This design architecture is advantageous when constructing a lightweight and compact instrument because (1) the frame acts like a jig and facilitates filter integration with the FPA, (2) the frame can be designed so as to maximize the FPA field of view, (3) the frame can be simultaneously used as a baffle for mitigating crosstalk, and (4) micron-scale alignment features can be patterned so as to permit high-precision filter stacking and, consequently, increase the filter bandwidth and sharpen the out-of-band rolloff. The second technology consists of leveraging, from another project, compact and lightweight Bi0.87Sb0.13/Sb arrayed thermopiles. These detectors consist of 30-layer thermopiles deposited in series upon a silicon nitride membrane. At 300 K, the thermopile arrays are highly linear over many orders of magnitude of incident IR power, and have a reported specific detectivity that exceeds the requirements imposed on future mission concepts. The bandpass filter array board is integrated with a thermopile array board by mounting both boards on a machined aluminum jig.

A SSVEP Stimuli Encoding Method Using Trinary Frequency-Shift Keying Encoded SSVEP (TFSK-SSVEP)

PubMed Central

Zhao, Xing; Zhao, Dechun; Wang, Xia; Hou, Xiaorong

2017-01-01

SSVEP is a kind of BCI technology with advantage of high information transfer rate. However, due to its nature, frequencies could be used as stimuli are scarce. To solve such problem, a stimuli encoding method which encodes SSVEP signal using Frequency Shift–Keying (FSK) method is developed. In this method, each stimulus is controlled by a FSK signal which contains three different frequencies that represent “Bit 0,” “Bit 1” and “Bit 2” respectively. Different to common BFSK in digital communication, “Bit 0” and “Bit 1” composited the unique identifier of stimuli in binary bit stream form, while “Bit 2” indicates the ending of a stimuli encoding. EEG signal is acquired on channel Oz, O1, O2, Pz, P3, and P4, using ADS1299 at the sample rate of 250 SPS. Before original EEG signal is quadrature demodulated, it is detrended and then band-pass filtered using FFT-based FIR filtering to remove interference. Valid peak of the processed signal is acquired by calculating its derivative and converted into bit stream using window method. Theoretically, this coding method could implement at least 2n−1 (n is the length of bit command) stimulus while keeping the ITR the same. This method is suitable to implement stimuli on a monitor and where the frequency and phase could be used to code stimuli is limited as well as implementing portable BCI devices which is not capable of performing complex calculations. PMID:28626393

A periodic spatio-spectral filter for event-related potentials.

PubMed

Ghaderi, Foad; Kim, Su Kyoung; Kirchner, Elsa Andrea

2016-12-01

With respect to single trial detection of event-related potentials (ERPs), spatial and spectral filters are two of the most commonly used pre-processing techniques for signal enhancement. Spatial filters reduce the dimensionality of the data while suppressing the noise contribution and spectral filters attenuate frequency components that most likely belong to noise subspace. However, the frequency spectrum of ERPs overlap with that of the ongoing electroencephalogram (EEG) and different types of artifacts. Therefore, proper selection of the spectral filter cutoffs is not a trivial task. In this research work, we developed a supervised method to estimate the spatial and finite impulse response (FIR) spectral filters, simultaneously. We evaluated the performance of the method on offline single trial classification of ERPs in datasets recorded during an oddball paradigm. The proposed spatio-spectral filter improved the overall single-trial classification performance by almost 9% on average compared with the case that no spatial filters were used. We also analyzed the effects of different spectral filter lengths and the number of retained channels after spatial filtering. Copyright © 2016. Published by Elsevier Ltd.

Artifact removal from EEG signals using adaptive filters in cascade

NASA Astrophysics Data System (ADS)

Garcés Correa, A.; Laciar, E.; Patiño, H. D.; Valentinuzzi, M. E.

2007-11-01

Artifacts in EEG (electroencephalogram) records are caused by various factors, like line interference, EOG (electro-oculogram) and ECG (electrocardiogram). These noise sources increase the difficulty in analyzing the EEG and to obtaining clinical information. For this reason, it is necessary to design specific filters to decrease such artifacts in EEG records. In this paper, a cascade of three adaptive filters based on a least mean squares (LMS) algorithm is proposed. The first one eliminates line interference, the second adaptive filter removes the ECG artifacts and the last one cancels EOG spikes. Each stage uses a finite impulse response (FIR) filter, which adjusts its coefficients to produce an output similar to the artifacts present in the EEG. The proposed cascade adaptive filter was tested in five real EEG records acquired in polysomnographic studies. In all cases, line-frequency, ECG and EOG artifacts were attenuated. It is concluded that the proposed filter reduces the common artifacts present in EEG signals without removing significant information embedded in these records.

Far infrared filters for the Galileo-Jupiter and other missions

NASA Technical Reports Server (NTRS)

Seeley, J. S.; Hunneman, R.; Whatley, A.

1981-01-01

Progress in the development of FIR multilayer interference filters for the net flux radiometer and photopolarizing radiometer to be carried on board the Galileo mission to Jupiter is reported. The multilayer interference technique has been extended to the region above 40 microns by the use of PbTe/II-VI materials in hard-coated combination, with the thickest layers composed of CdSe QWOT at 74 microns and PbTe QWOT. Improvements have also been obtained in filters below 20 microns on the basis of the Chebyshev stack design. A composite filter cutting on steeply at 40 microns has been designed which employs a thin crystal quartz substrate, shorter wavelength absorption in ZnS and As2S3 thin films, and supplementary multilayer interference. Finally, absorptive filters have been developed based on II-VI compounds in multilayer combination with KRS-5 (or 6) on a KRS-5 (or 6) substrate

Compact Micromachined Bandpass Filters for Infrared Planetary Spectroscopy

NASA Technical Reports Server (NTRS)

Brown, Ari D.; Aslam, Shahid; Chervenak, James A.; Huang, Wei-Chung; Merrell, Willie; Quijada, Manuel

2011-01-01

The thermal instrument strawman payload of the Jupiter Europa Orbiter on the Europa Jupiter Science Mission will map out thermal anomalies, the structure, and atmospheric conditions of Europa and Jupiter within the 7-100 micron spectral range. One key requirement for the payload is that the mass cannot exceed 3.7 kg. Consequently, a new generation of light-weight miniaturized spectrometers needs to be developed. On the path toward developing these spectrometers is development of ancillary miniaturized spectroscopic components. In this paper, we present a strategy for making radiation hard and low mass FIR band pass metal mesh filters. Our strategy involves using MEMS-based fabrication techniques, which will permit the quasi-optical filter structures to be made with micron-scale precision. This will enable us to achieve tight control over both the pass band of the filter and the micromachined silicon support structure architecture, which will facilitate integration of the filters for a variety of applications.

Do trees smart from ozone

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

Douglas-firs near Eatonville, Washington - 70 miles south of Seattle - are getting doses of ozone pollution at levels regularly found in Los Angeles. Ozone levels of 220 parts per billion (ppb) can make your eyes smart and give your Aunt Edna a doozy of a headache. University of Washington researchers are now trying to find if Douglas-fir is adversely affected by 220 ppb of ozone. They are also studying whether individual branches can reveal how whole trees respond to pollutants. Studying entire trees is tough so researchers hope to take the pulse of a tree by examining its branches.more » At the university's experimental forest, researchers have placed 12-foot-tall plastic-covered corrals around six Douglas-firs, each nine or 10 years old and up to 15 feet tall. Three of the trees receive filtered air while three others are blasted with 220 ppb of ozone for eight hours each day. Four individual branches on each tree are encased in their own plastic chambers. Two are dosed with filtered air and two with ozone. To date, the UW research is the only study in the US combining branch chambers with whole tree measurements. Now in its second year, the experiment is expected to yield information about growth and foliage health by measuring respiration, chlorophyll, photosynthesis, and nutrient uptake. Loss of tree vigor could lead to increased problems with pathogens and insects. In the summer of '88, surprisingly high levels of ozone - up to 196 ppb - were detected in forests downwind from Seattle, worse than the urban areas themselves.« less

Joint polarization tracking and channel equalization based on radius-directed linear Kalman filter

NASA Astrophysics Data System (ADS)

Zhang, Qun; Yang, Yanfu; Zhong, Kangping; Liu, Jie; Wu, Xiong; Yao, Yong

2018-01-01

We propose a joint polarization tracking and channel equalization scheme based on radius-directed linear Kalman filter (RD-LKF) by introducing the butterfly finite-impulse-response (FIR) filter in our previously proposed RD-LKF method. Along with the fast polarization tracking, it can also simultaneously compensate the inter-symbol interference (ISI) effects including residual chromatic dispersion and polarization mode dispersion. Compared with the conventional radius-directed equalizer (RDE) algorithm, it is demonstrated experimentally that three times faster convergence speed, one order of magnitude better tracking capability, and better BER performance is obtained in polarization division multiplexing 16 quadrature amplitude modulation system. Besides, the influences of the algorithm parameters on the convergence and the tracking performance are investigated by numerical simulation.

Zero-phase FIR filters: Blessing or curse?

NASA Astrophysics Data System (ADS)

Scherbaum, Frank

These are exciting times for observational seismology. State-of-the-art broadband seismometers now easily cover a frequency band of more than one hundred seconds to several tens of Hertz in a single sensor. Commonly available data loggers provide a dynamic range exceeding 120 dB. Ground motion amplitudes differing by more than 6 orders of magnitude can be simultaneously recorded without distortion.

Portuguese food composition database quality management system.

PubMed

Oliveira, L M; Castanheira, I P; Dantas, M A; Porto, A A; Calhau, M A

2010-11-01

The harmonisation of food composition databases (FCDB) has been a recognised need among users, producers and stakeholders of food composition data (FCD). To reach harmonisation of FCDBs among the national compiler partners, the European Food Information Resource (EuroFIR) Network of Excellence set up a series of guidelines and quality requirements, together with recommendations to implement quality management systems (QMS) in FCDBs. The Portuguese National Institute of Health (INSA) is the national FCDB compiler in Portugal and is also a EuroFIR partner. INSA's QMS complies with ISO/IEC (International Organization for Standardisation/International Electrotechnical Commission) 17025 requirements. The purpose of this work is to report on the strategy used and progress made for extending INSA's QMS to the Portuguese FCDB in alignment with EuroFIR guidelines. A stepwise approach was used to extend INSA's QMS to the Portuguese FCDB. The approach included selection of reference standards and guides and the collection of relevant quality documents directly or indirectly related to the compilation process; selection of the adequate quality requirements; assessment of adequacy and level of requirement implementation in the current INSA's QMS; implementation of the selected requirements; and EuroFIR's preassessment 'pilot' auditing. The strategy used to design and implement the extension of INSA's QMS to the Portuguese FCDB is reported in this paper. The QMS elements have been established by consensus. ISO/IEC 17025 management requirements (except 4.5) and 5.2 technical requirements, as well as all EuroFIR requirements (including technical guidelines, FCD compilation flowchart and standard operating procedures), have been selected for implementation. The results indicate that the quality management requirements of ISO/IEC 17025 in place in INSA fit the needs for document control, audits, contract review, non-conformity work and corrective actions, and users' (customers') comments, complaints and satisfaction, with minor adaptation. Implementation of the FCDB QMS proved to be a way of reducing the subjectivity of the compilation process and fully documenting it, and also facilitates training of new compilers. Furthermore, it has strengthened cooperation and trust among FCDB actors, as all of them were called to be involved in the process. On the basis of our practical results, we can conclude that ISO/IEC 17025 management requirements are an adequate reference for the implementation of INSA's FCDB QMS with the advantages of being well known to all members of staff and also being a common quality language among laboratories producing FCD. Combining quality systems and food composition activities endows the FCDB compilation process with flexibility, consistency and transparency, and facilitates its monitoring and assessment, providing the basis for strengthening confidence among users, data producers and compilers.

Recursive inversion of externally defined linear systems by FIR filters

NASA Technical Reports Server (NTRS)

Bach, Ralph E., Jr.; Baram, Yoram

1989-01-01

The approximate inversion of an internally unknown linear system, given by its impulse response sequence, by an inverse system having a finite impulse response, is considered. The recursive least-squares procedure is shown to have an exact initialization, based on the triangular Toeplitz structure of the matrix involved. The proposed approach also suggests solutions to the problem of system identification and compensation.

Direct Sequence Spread Spectrum (DSSS) Receiver, User Manual

DTIC Science & Technology

2008-01-01

sampled data is clocked in to correlator data registers and a comparison is made between the code and data register contents, producing a correlation ...symbol (equal to the processing gain Gp ) but need not be otherwise synchronised with the spreading codes . This allows a very long and noise- like PRBS...and Q channels are independently but synchronously sampled . Complex Real ADC FIR Filter Interpolator Acquisition Correlators

Remote sensing of atmospheric chemistry; Proceedings of the Meeting, Orlando, FL, Apr. 1-3, 1991

NASA Technical Reports Server (NTRS)

Mcelroy, James L. (Editor); Mcneal, Robert J. (Editor)

1991-01-01

The present volume on remote sensing of atmospheric chemistry discusses special remote sensing space observations and field experiments to study chemical change in the atmosphere, network monitoring for detection of stratospheric chemical change, stratospheric chemistry studies, and the combining of model, in situ, and remote sensing in atmospheric chemistry. Attention is given to the measurement of tropospheric carbon monoxide using gas filter radiometers, long-path differential absorption measurements of tropospheric molecules, air quality monitoring with the differential optical absorption spectrometer, and a characterization of tropospheric methane through space-based remote sensing. Topics addressed include microwave limb sounder experiments for UARS and EOS, an overview of the spectroscopy of the atmosphere using an FIR emission experiment, the detection of stratospheric ozone trends by ground-based microwave observations, and a FIR Fabry-Perot spectrometer for OH measurements.

Equalizing secondary path effects using the periodicity of fMRI acoustic noise.

PubMed

Kannan, Govind; Milani, Ali A; Panahi, Issa; Briggs, Richard

2008-01-01

Non-minimum phase secondary path has a direct effect on achieving a desired noise attenuation level in active noise control (ANC) systems. The adaptive noise canceling filter is often a causal FIR filter which may not be able to sufficiently equalize the effect of a non-minimum phase secondary path, since in theory only a non-causal filter can equalize it. However a non-causal stable filter can be found to equalize the non-minimum phase effect of secondary path. Realization of non-causal stable filters requires knowledge of future values of input signal. In this paper we develop methods for equalizing the non-minimum phase property of the secondary path and improving the performance of an ANC system by exploiting the periodicity of fMRI acoustic noise. It has been shown that the scanner noise component is highly periodic and hence predictable which enables easy realization of non-causal filtering. Improvement in performance due to the proposed methods (with and without the equalizer) is shown for periodic fMRI acoustic noise.

A C Language Implementation of the SRO (Murdock) Detector/Analyzer

USGS Publications Warehouse

Murdock, James N.; Halbert, Scott E.

1991-01-01

A signal detector and analyzer algorithm was described by Murdock and Hutt in 1983. The algorithm emulates the performance of a human interpreter of seismograms. It estimates the signal onset, the direction of onset (positive or negative), the quality of these determinations, the period and amplitude of the signal, and the background noise at the time of the signal. The algorithm has been coded in C language for implementation as a 'blackbox' for data similar to that of the China Digital Seismic Network. A driver for the algorithm is included, as are suggestions for other drivers. In all of these routines, plus several FIR filters that are included as well, floating point operations are not required. Multichannel operation is supported. Although the primary use of the code has been for in-house processing of broadband and short period data of the China Digital Seismic Network, provisions have been made to process the long period and very long period data of that system as well. The code for the in-house detector, which runs on a mini-computer, is very similar to that of the field system, which runs on a microprocessor. The code is documented.

Acquisition, Image and Data Compression.

DTIC Science & Technology

1983-04-30

considered, self well to the freq.ency hcppe! signal arpli’a- ,i n. This loop aol Itn i ociltei w’efors are hown in Firs. la,h. 71;n r’tine wav ’-f, m...thei siiiillaiieiuts spacie midi slllitial tre(tivelicy 26. 1). .ui-.u.ii m~ill It. V. K. N’iu.a~ kiar Appl. Ot IS, ti673 filtering tt i-I ) sit .imls

Sub-threshold standard cell library design for ultra-low power biomedical applications.

PubMed

Li, Ming-Zhong; Ieong, Chio-In; Law, Man-Kay; Mak, Pui-In; Vai, Mang-I; Martins, Rui P

2013-01-01

Portable/Implantable biomedical applications usually exhibit stringent power budgets for prolonging battery life time, but loose operating frequency requirements due to small bio-signal bandwidths, typically below a few kHz. The use of sub-threshold digital circuits is ideal in such scenario to achieve optimized power/speed tradeoffs. This paper discusses the design of a sub-threshold standard cell library using a standard 0.18-µm CMOS technology. A complete library of 56 standard cells is designed and the methodology is ensured through schematic design, transistor width scaling and layout design, as well as timing, power and functionality characterization. Performance comparison between our sub-threshold standard cell library and a commercial standard cell library using a 5-stage ring oscillator and an ECG designated FIR filter is performed. Simulation results show that our library achieves a total power saving of 95.62% and a leakage power reduction of 97.54% when compared with the same design implemented by the commercial standard cell library (SCL).

Fundamentals handbook of electrical and computer engineering. Volume 1 Circuits fields and electronics

NASA Astrophysics Data System (ADS)

Chang, S. S. L.

State of the art technology in circuits, fields, and electronics is discussed. The principles and applications of these technologies to industry, digital processing, microwave semiconductors, and computer-aided design are explained. Important concepts and methodologies in mathematics and physics are reviewed, and basic engineering sciences and associated design methods are dealt with, including: circuit theory and the design of magnetic circuits and active filter synthesis; digital signal processing, including FIR and IIR digital filter design; transmission lines, electromagnetic wave propagation and surface acoustic wave devices. Also considered are: electronics technologies, including power electronics, microwave semiconductors, GaAs devices, and magnetic bubble memories; digital circuits and logic design.

End-point controller design for an experimental two-link flexible manipulator using convex optimization

NASA Technical Reports Server (NTRS)

Oakley, Celia M.; Barratt, Craig H.

1990-01-01

Recent results in linear controller design are used to design an end-point controller for an experimental two-link flexible manipulator. A nominal 14-state linear-quadratic-Gaussian (LQG) controller was augmented with a 528-tap finite-impulse-response (FIR) filter designed using convex optimization techniques. The resulting 278-state controller produced improved end-point trajectory tracking and disturbance rejection in simulation and experimentally in real time.

Two-Dimensional Signal Processing, Optical Information Storage and Processing, and Electromagnetic Measurements

DTIC Science & Technology

1992-07-15

Modeling SENIOR PRINCIPAL INVESTIGATOR: R. M. Mersereau, Regents’ Professor SCIENTIFIC PERSONNEL: F. J. Malassenet, (Ph.D. received, Dec. 1991) T. R. Gardos ...multiprocessor environment. RESEARCH ACCOMPLISHMENTS: Students Gardos , Martucci, Rao, and Truong were partially supported using funds supplied by Georgia...pp. 21- 56, 1991. [4] T. R. Gardos and R. M. Mersereau, "FIR Filtering on a Lattice with Periodically Deleted Samples," Proc. 1991 IEEE Int. Conf

77 FR 472 - National Advisory Committee for Implementation of the National Forest System Land Management...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-01-05

... DEPARTMENT OF AGRICULTURE Forest Service National Advisory Committee for Implementation of the National Forest System Land Management Planning Rule; Correction AGENCY: USDA Forest Service. ACTION... for the deaf (TDD) may call the Federal Information Relay Service (FIRS) at 1 (800) 877-8339 between 8...

Study of quadrature FIR filters for extraction of low-frequency instantaneous information in biophysical signals

NASA Astrophysics Data System (ADS)

Arce-Guevara, Valdemar E.; Alba-Cadena, Alfonso; Mendez, Martín O.

Quadrature bandpass filters take a real-valued signal and output an analytic signal from which the instantaneous amplitude and phase can be computed. For this reason, they represent a useful tool to extract time-varying, narrow-band information from electrophysiological signals such as electroencephalogram (EEG) or electrocardiogram. One of the defining characteristics of quadrature filters is its null response to negative frequencies. However, when the frequency band of interest is close to 0 Hz, a careless filter design could let through negative frequencies, producing distortions in the amplitude and phase of the output. In this work, three types of quadrature filters (Ideal, Gabor and Sinusoidal) have been evaluated using both artificial and real EEG signals. For the artificial signals, the performance of each filter was measured in terms of the distortion in amplitude and phase, and sensitivity to noise and bandwidth selection. For the real EEG signals, a qualitative evaluation of the dynamics of the synchronization between two EEG channels was performed. The results suggest that, while all filters under study behave similarly under noise, they differ in terms of their sensitivity to bandwidth choice. In this study, the Sinusoidal filter showed clear advantages for the estimation of low-frequency EEG synchronization.

An Efficient Implementation For Real Time Applications Of The Wigner-Ville Distribution

NASA Astrophysics Data System (ADS)

Boashash, Boualem; Black, Peter; Whitehouse, Harper J.

1986-03-01

The Wigner-Ville Distribution (WVD) is a valuable tool for time-frequency signal analysis. In order to implement the WVD in real time an efficient algorithm and architecture have been developed which may be implemented with commercial components. This algorithm successively computes the analytic signal corresponding to the input signal, forms a weighted kernel function and analyses the kernel via a Discrete Fourier Transform (DFT). To evaluate the analytic signal required by the algorithm it is shown that the time domain definition implemented as a finite impulse response (FIR) filter is practical and more efficient than the frequency domain definition of the analytic signal. The windowed resolution of the WVD in the frequency domain is shown to be similar to the resolution of a windowed Fourier Transform. A real time signal processsor has been designed for evaluation of the WVD analysis system. The system is easily paralleled and can be configured to meet a variety of frequency and time resolutions. The arithmetic unit is based on a pair of high speed VLSI floating-point multiplier and adder chips. Dual operand buses and an independent result bus maximize data transfer rates. The system is horizontally microprogrammed and utilizes a full instruction pipeline. Each microinstruction specifies two operand addresses, a result location, the type of arithmetic and the memory configuration. input and output is via shared memory blocks with front-end processors to handle data transfers during the non access periods of the analyzer.

Multi-DSP and FPGA based Multi-channel Direct IF/RF Digital receiver for atmospheric radar

NASA Astrophysics Data System (ADS)

Yasodha, Polisetti; Jayaraman, Achuthan; Kamaraj, Pandian; Durga rao, Meka; Thriveni, A.

2016-07-01

Modern phased array radars depend highly on digital signal processing (DSP) to extract the echo signal information and to accomplish reliability along with programmability and flexibility. The advent of ASIC technology has made various digital signal processing steps to be realized in one DSP chip, which can be programmed as per the application and can handle high data rates, to be used in the radar receiver to process the received signal. Further, recent days field programmable gate array (FPGA) chips, which can be re-programmed, also present an opportunity to utilize them to process the radar signal. A multi-channel direct IF/RF digital receiver (MCDRx) is developed at NARL, taking the advantage of high speed ADCs and high performance DSP chips/FPGAs, to be used for atmospheric radars working in HF/VHF bands. Multiple channels facilitate the radar t be operated in multi-receiver modes and also to obtain the wind vector with improved time resolution, without switching the antenna beam. MCDRx has six channels, implemented on a custom built digital board, which is realized using six numbers of ADCs for simultaneous processing of the six input signals, Xilinx vertex5 FPGA and Spartan6 FPGA, and two ADSPTS201 DSP chips, each of which performs one phase of processing. MCDRx unit interfaces with the data storage/display computer via two gigabit ethernet (GbE) links. One of the six channels is used for Doppler beam swinging (DBS) mode and the other five channels are used for multi-receiver mode operations, dedicatedly. Each channel has (i) ADC block, to digitize RF/IF signal, (ii) DDC block for digital down conversion of the digitized signal, (iii) decoding block to decode the phase coded signal, and (iv) coherent integration block for integrating the data preserving phase intact. ADC block consists of Analog devices make AD9467 16-bit ADCs, to digitize the input signal at 80 MSPS. The output of ADC is centered around (80 MHz - input frequency). The digitized data is fed to DDC block, which down converts the data to base-band. The DDC block has NCO, mixer and two chains of Bessel filters (fifth order cascaded integration comb filter, two FIR filters, two half band filters and programmable FIR filters) for in-phase (I) and Quadrature phase (Q) channels. The NCO has 32 bits and is set to match the output frequency of ADC. Further, DDC down samples (decimation) the data and reduces the data rate to 16 MSPS. This data is further decimated and the data rate is reduced down to 4/2/1/0.5/0.25/0.125/0.0625 MSPS for baud lengths 0.25/0.5/1/2/4/8/16 μs respectively. The down sampled data is then fed to decoding block, which performs cross correlation to achieve pulse compression of the binary-phase coded data to obtain better range resolution with maximum possible height coverage. This step improves the signal power by a factor equal to the length of the code. Coherent integration block integrates the decoded data coherently for successive pulses, which improves the signal to noise ratio and reduces the data volume. DDC, decoding and coherent integration blocks are implemented in Xilinx vertex5 FPGA. Till this point, function of all six channels is same for DBS mode and multi-receiver modes. Data from vertex5 FPGA is transferred to PC via GbE-1 interface for multi-modes or to two Analog devices make ADSP-TS201 DSP chips (A and B), via link port for DBS mode. ADSP-TS201 chips perform the normalization, DC removal, windowing, FFT computation and spectral averaging on the data, which is transferred to storage/display PC via GbE-2 interface for real-time data display and data storing. Physical layer of GbE interface is implemented in an external chip (Marvel 88E1111) and MAC layer is implemented internal to vertex5 FPGA. The MCDRx has total 4 GB of DDR2 memory for data storage. Spartan6 FPGA is used for generating timing signals, required for basic operation of the radar and testing of the MCDRx.

A Dynamic Attitude Measurement System Based on LINS

PubMed Central

Li, Hanzhou; Pan, Quan; Wang, Xiaoxu; Zhang, Juanni; Li, Jiang; Jiang, Xiangjun

2014-01-01

A dynamic attitude measurement system (DAMS) is developed based on a laser inertial navigation system (LINS). Three factors of the dynamic attitude measurement error using LINS are analyzed: dynamic error, time synchronization and phase lag. An optimal coning errors compensation algorithm is used to reduce coning errors, and two-axis wobbling verification experiments are presented in the paper. The tests indicate that the attitude accuracy is improved 2-fold by the algorithm. In order to decrease coning errors further, the attitude updating frequency is improved from 200 Hz to 2000 Hz. At the same time, a novel finite impulse response (FIR) filter with three notches is designed to filter the dither frequency of the ring laser gyro (RLG). The comparison tests suggest that the new filter is five times more effective than the old one. The paper indicates that phase-frequency characteristics of FIR filter and first-order holder of navigation computer constitute the main sources of phase lag in LINS. A formula to calculate the LINS attitude phase lag is introduced in the paper. The expressions of dynamic attitude errors induced by phase lag are derived. The paper proposes a novel synchronization mechanism that is able to simultaneously solve the problems of dynamic test synchronization and phase compensation. A single-axis turntable and a laser interferometer are applied to verify the synchronization mechanism. The experiments results show that the theoretically calculated values of phase lag and attitude error induced by phase lag can both match perfectly with testing data. The block diagram of DAMS and physical photos are presented in the paper. The final experiments demonstrate that the real-time attitude measurement accuracy of DAMS can reach up to 20″ (1σ) and the synchronization error is less than 0.2 ms on the condition of three axes wobbling for 10 min. PMID:25177802

Filter design for cancellation of baseline-fluctuation in needle EMG recordings.

PubMed

Rodríguez-Carreño, I; Malanda-Trigueros, A; Gila-Useros, L; Navallas-Irujo, J; Rodríguez-Falces, J

2006-01-01

Appropriate cancellation of the baseline fluctuation (BLF) is an important issue when recording EMG signals as it may degrade signal quality and distort qualitative and quantitative analysis. We present a novel filter-design approach for automatic cancellation of the BLF based on several signal processing techniques used sequentially. The methodology is to estimate the spectral content of the BLF, and then to use this estimation to design a high-pass FIR filter that cancel the BLF present in the signal. Two merit figures are devised for measuring the degree of BLF present in an EMG record. These figures are used to compare our method with the conventional approach, which naively considers the baseline course to be of constant (without any fluctuation) potential shift. Applications of the technique on real and simulated EMG signals show the superior performance of our approach in terms of both visual inspection and the merit figures.

Digital Audio Signal Processing and Nde: AN Unlikely but Valuable Partnership

NASA Astrophysics Data System (ADS)

Gaydecki, Patrick

2008-02-01

In the Digital Signal Processing (DSP) group, within the School of Electrical and Electronic Engineering at The University of Manchester, research is conducted into two seemingly distinct and disparate subjects: instrumentation for nondestructive evaluation, and DSP systems & algorithms for digital audio. We have often found that many of the hardware systems and algorithms employed to recover, extract or enhance audio signals may also be applied to signals provided by ultrasonic or magnetic NDE instruments. Furthermore, modern DSP hardware is so fast (typically performing hundreds of millions of operations per second), that much of the processing and signal reconstruction may be performed in real time. Here, we describe some of the hardware systems we have developed, together with algorithms that can be implemented both in real time and offline. A next generation system has now been designed, which incorporates a processor operating at 0.55 Giga MMACS, six input and eight output analogue channels, digital input/output in the form of S/PDIF, a JTAG and a USB interface. The software allows the user, with no knowledge of filter theory or programming, to design and run standard or arbitrary FIR, IIR and adaptive filters. Using audio as a vehicle, we can demonstrate the remarkable properties of modern reconstruction algorithms when used in conjunction with such hardware; applications in NDE include signal enhancement and recovery in acoustic, ultrasonic, magnetic and eddy current modalities.

A comparison of coupled biogeophysical and biogeochemical dynamics across a precipitation gradient in Oregon using data assimilation

NASA Astrophysics Data System (ADS)

Pettijohn, J. C.; Law, B. E.; Williams, M. D.; Stoekli, R.; Thornton, P. E.; Thomas, C. K.; Hudiburg, T. W.; Martin, J.

2010-12-01

We present results from our coupled biophysical - biochemical model data fusion (MDF) analysis across a climatic gradient in Oregon, USA, using data from a coast-range Douglas-fir (US-Fir; 2006-2008) and a semi-arid ponderosa pine (US-Me2; 2002-2008) AmeriFlux site. Our MDF scheme couples the Ensemble Kalman Filter (EnKF) with the National Center for Atmospheric Research (NCAR) Community Land Model with Carbon-Nitrogen coupling (CLM-CN, version 3.5). Assimilated data includes continuous eddy covariance measurements of forest-atmosphere CO2 (NEE, net ecosystem exchange) and water vapor fluxes (λE, latent heat flux), chamber-based soil respiratory flux, soil moisture and temperature, snow depth (US-Me2), MODIS-derived 8 day LAI, and carbon and nitrogen pools. We quantify the ecosystem carbon and nitrogen budgets, partition NEE and λE fluxes, and thus increase confidence in multi-scale controls on CO2 and water vapor exchange. The MDF did a better job predicting NEE than λE at both sites (r2 = 0.86 for NEE at both sites; λE r2 = 0.65 and 0.63 at the US-ME2 and US-Fir sites, respectively) partly due to a weighting scheme we prescribed for NEE. The distribution of carbon and nitrogen differed significantly between sites, with total ecosystem carbon (vegetation, detritus, soil) of the US-Fir site being about 1.4 times higher than the US-Me2 site (35 kg C m-2 vs. 25 kg C m-2). Mean NEE over overlapping water years ‘07-‘08 was -495 gC m-2 at the US-Me2 site as opposed to -809 gC m-2 at the US-Fir site, nearly a two-fold difference in C uptake across this precipitation gradient. Average GPP and ecosystem respiration (Re) over these two water years were both ~1.7x greater at the US-Fir site, with 1712 gC m^-2 and 1217 gC m-2, respectively, at the US-Me2 site vs. 2841 gC m-2 and 2032 gC m-2 at the US-Fir. Autotrophic respiration contributed 79% and 72% to the Re flux at the US-Me2 and US-Fir sites, respectively, with total soil respiration contributing 53% and 58% to Re. While a comparison of observed and MDF environmental response functions suggests both root-zone soil moisture and leaf-to-air VPD photosynthetic controls at both sites, the MDF did not impose CLM-CN’s soil stress upon photosynthesis at the US-Fir site, suggesting the apparent soil moisture response arises from correlations with other driving variables such as VPD. In summary, we demonstrate that MDF analysis can help constrain coupled ecosystem carbon and water dynamics by combining long-term ecosystem measurements by incorporating necessary measurement and model uncertainties.

A Multi Directional Perfect Reconstruction Filter Bank Designed with 2-D Eigenfilter Approach: Application to Ultrasound Speckle Reduction.

PubMed

Nagare, Mukund B; Patil, Bhushan D; Holambe, Raghunath S

2017-02-01

B-Mode ultrasound images are degraded by inherent noise called Speckle, which creates a considerable impact on image quality. This noise reduces the accuracy of image analysis and interpretation. Therefore, reduction of speckle noise is an essential task which improves the accuracy of the clinical diagnostics. In this paper, a Multi-directional perfect-reconstruction (PR) filter bank is proposed based on 2-D eigenfilter approach. The proposed method used for the design of two-dimensional (2-D) two-channel linear-phase FIR perfect-reconstruction filter bank. In this method, the fan shaped, diamond shaped and checkerboard shaped filters are designed. The quadratic measure of the error function between the passband and stopband of the filter has been used an objective function. First, the low-pass analysis filter is designed and then the PR condition has been expressed as a set of linear constraints on the corresponding synthesis low-pass filter. Subsequently, the corresponding synthesis filter is designed using the eigenfilter design method with linear constraints. The newly designed 2-D filters are used in translation invariant pyramidal directional filter bank (TIPDFB) for reduction of speckle noise in ultrasound images. The proposed 2-D filters give better symmetry, regularity and frequency selectivity of the filters in comparison to existing design methods. The proposed method is validated on synthetic and real ultrasound data which ensures improvement in the quality of ultrasound images and efficiently suppresses the speckle noise compared to existing methods.

Time Delay Estimation

DTIC Science & Technology

1976-04-09

of the signal and noise remain HH ***^-^*--~ 53 h, to r(Mc) h2(r» r(we) Figure 3-2 Sy&toetric Impulse Response for Two FIR Linear Phase...Inputs x,y and Outputs x.j. , 15 2-2 Linear System with Impulse Response h("r) 23 2-3 Model of Error Resulting from Linearly Filtering x(t) to...Corrupted with Additive Noise 42 2-6 Model of Directional Signal Corrupted with Additive Noise and Processed .... 45 2-7 Source Driving Two

Derivative information recovery by a selective integration technique

NASA Technical Reports Server (NTRS)

Johnson, M. A.

1974-01-01

A nonlinear stationary homogeneous digital filter DIRSIT (derivative information recovery by a selective integration technique) is investigated. The spectrum of a quasi-linear discrete describing function (DDF) to DIRSIT is obtained by a digital measuring scheme. A finite impulse response (FIR) approximation to the quasi-linearization is then obtained. Finally, DIRSIT is compared with its quasi-linear approximation and with a standard digital differentiating technique. Results indicate the effects of DIRSIT on a wide variety of practical signals.

A new design approach to MMI-based (de)multiplexers

NASA Astrophysics Data System (ADS)

Yueyu, Xiao; Sailing, He

2004-09-01

A novel design method of the wavelength (de)multiplexer is presented. The output spectral response of a (de)multiplexer is designed from the view of FIR filters. Avoiding laborious mathematic analysis, the (de)multiplexer is analyzed and designed in this explicit and simple method. A four channel (de)multiplexer based on multimode interference (MMI) is designed as an example. The result obtained agrees with that of the commonly used method, and is verified by a finite difference beam propagation method (FDBPM) simulation.

Report on Contract F05611-76-90203. Volume I.

DTIC Science & Technology

1976-01-01

The most serious of these assumptions used in the development of the algorithms was that the sensors in use are much better than they really are...This was not the fault of the AFIT personnel, since the algo- rithus they developed used the best information about the sensors which they had at the...phase response for the first FIR filters. In the region trom 0.01 Hz to 0.1 liz the tiltmeter controls the servo. However, above 0. Ili the seismo-neter

Differential Frequency Hopping (DFH) Modulation for Underwater Acoustic Communications and Networking

DTIC Science & Technology

2009-10-09

trains the coefficients c of a finite impulse response (FIR) filter by gradient descent. The coefficients at iteration k + 1 are computed with the update... absorption . Figure 9 shows the reflection loss as a function of grazing angle for this bottom model. Note that below 30◦ this bottom model predicts...less than 1 dB loss per ray bounce. 11 Figure 9: Jackson bottom reflection loss for sand at 15 kHz Absorption Loss The absorption loss in the medium was

Adaptively combined FIR and functional link artificial neural network equalizer for nonlinear communication channel.

PubMed

Zhao, Haiquan; Zhang, Jiashu

2009-04-01

This paper proposes a novel computational efficient adaptive nonlinear equalizer based on combination of finite impulse response (FIR) filter and functional link artificial neural network (CFFLANN) to compensate linear and nonlinear distortions in nonlinear communication channel. This convex nonlinear combination results in improving the speed while retaining the lower steady-state error. In addition, since the CFFLANN needs not the hidden layers, which exist in conventional neural-network-based equalizers, it exhibits a simpler structure than the traditional neural networks (NNs) and can require less computational burden during the training mode. Moreover, appropriate adaptation algorithm for the proposed equalizer is derived by the modified least mean square (MLMS). Results obtained from the simulations clearly show that the proposed equalizer using the MLMS algorithm can availably eliminate various intensity linear and nonlinear distortions, and be provided with better anti-jamming performance. Furthermore, comparisons of the mean squared error (MSE), the bit error rate (BER), and the effect of eigenvalue ratio (EVR) of input correlation matrix are presented.

Static and Dynamic Characteristics of DC-DC Converter Using a Digital Filter

NASA Astrophysics Data System (ADS)

Kurokawa, Fujio; Okamatsu, Masashi

This paper presents the regulation and dynamic characteristics of the dc-dc converter with digital PID control, the minimum phase FIR filter or the IIR filter, and then the design criterion to improve the dynamic characteristics is discussed. As a result, it is clarified that the DC-DC converter using the IIR filter method has superior performance characteristics. The regulation range is within 1.3%, the undershoot against the step change of the load is less than 2% and the transient time is less than 0.4ms with the IIR filter method. In this case, the switching frequency is 100kHz and the step change of the load R is from 50 Ω to 10 Ω. Further, the superior characteristics are obtained when the first gain, the second gain and the second cut-off frequency are relatively large, and the first cut-off frequency and the passing frequency are relatively low. Moreover, it is important that the gain strongly decreases at the second cut-off frequency because the upper band pass frequency range must be always less than half of the sampling frequency based on the sampling theory.

Full value documentation in the Czech Food Composition Database.

PubMed

Machackova, M; Holasova, M; Maskova, E

2010-11-01

The aim of this project was to launch a new Food Composition Database (FCDB) Programme in the Czech Republic; to implement a methodology for food description and value documentation according to the standards designed by the European Food Information Resource (EuroFIR) Network of Excellence; and to start the compilation of a pilot FCDB. Foods for the initial data set were selected from the list of foods included in the Czech Food Consumption Basket. Selection of 24 priority components was based on the range of components used in former Czech tables. The priority list was extended with components for which original Czech analytical data or calculated data were available. Values that were input into the compiled database were documented according to the EuroFIR standards within the entities FOOD, COMPONENT, VALUE and REFERENCE using Excel sheets. Foods were described using the LanguaL Thesaurus. A template for documentation of data according to the EuroFIR standards was designed. The initial data set comprised documented data for 162 foods. Values were based on original Czech analytical data (available for traditional and fast foods, milk and milk products, wheat flour types), data derived from literature (for example, fruits, vegetables, nuts, legumes, eggs) and calculated data. The Czech FCDB programme has been successfully relaunched. Inclusion of the Czech data set into the EuroFIR eSearch facility confirmed compliance of the database format with the EuroFIR standards. Excel spreadsheets are applicable for full value documentation in the FCDB.

Time-domain prefilter design for enhanced tracking and vibration suppression in machine motion control

NASA Astrophysics Data System (ADS)

Cole, Matthew O. T.; Shinonawanik, Praween; Wongratanaphisan, Theeraphong

2018-05-01

Structural flexibility can impact negatively on machine motion control systems by causing unmeasured positioning errors and vibration at locations where accurate motion is important for task execution. To compensate for these effects, command signal prefiltering may be applied. In this paper, a new FIR prefilter design method is described that combines finite-time vibration cancellation with dynamic compensation properties. The time-domain formulation exploits the relation between tracking error and the moment values of the prefilter impulse response function. Optimal design solutions for filters having minimum H2 norm are derived and evaluated. The control approach does not require additional actuation or sensing and can be effective even without complete and accurate models of the machine dynamics. Results from implementation and testing on an experimental high-speed manipulator having a Delta robot architecture with directionally compliant end-effector are presented. The results show the importance of prefilter moment values for tracking performance and confirm that the proposed method can achieve significant reductions in both peak and RMS tracking error, as well as settling time, for complex motion patterns.

The new on-line Czech Food Composition Database.

PubMed

Machackova, Marie; Holasova, Marie; Maskova, Eva

2013-10-01

The new on-line Czech Food Composition Database (FCDB) was launched on http://www.czfcdb.cz in December 2010 as a main freely available channel for dissemination of Czech food composition data. The application is based on a complied FCDB documented according to the EuroFIR standardised procedure for full value documentation and indexing of foods by the LanguaL™ Thesaurus. A content management system was implemented for administration of the website and performing data export (comma-separated values or EuroFIR XML transport package formats) by a compiler. Reference/s are provided for each published value with linking to available freely accessible on-line sources of data (e.g. full texts, EuroFIR Document Repository, on-line national FCDBs). LanguaL™ codes are displayed within each food record as searchable keywords of the database. A photo (or a photo gallery) is used as a visual descriptor of a food item. The application is searchable on foods, components, food groups, alphabet and a multi-field advanced search. Copyright © 2013 Elsevier Ltd. All rights reserved.

Enchanced interference cancellation and telemetry reception in multipath environments with a single paraboic dish antenna using a focal plane array

NASA Technical Reports Server (NTRS)

Vilnrotter, Victor A. (Inventor); Mukai, Ryan (Inventor)

2011-01-01

An Advanced Focal Plane Array ("AFPA") for parabolic dish antennas that exploits spatial diversity to achieve better channel equalization performance in the presence of multipath (better than temporal equalization alone), and which is capable of receiving from two or more sources within a field-of-view in the presence of multipath. The AFPA uses a focal plane array of receiving elements plus a spatio-temporal filter that keeps information on the adaptive FIR filter weights, relative amplitudes and phases of the incoming signals, and which employs an Interference Cancelling Constant Modulus Algorithm (IC-CMA) that resolves multiple telemetry streams simultaneously from the respective aero-nautical platforms. This data is sent to an angle estimator to calculate the target's angular position, and then on to Kalman filters FOR smoothing and time series prediction. The resulting velocity and acceleration estimates from the time series data are sent to an antenna control unit (ACU) to be used for pointing control.

Signal propagation in cortical networks: a digital signal processing approach.

PubMed

Rodrigues, Francisco Aparecido; da Fontoura Costa, Luciano

2009-01-01

This work reports a digital signal processing approach to representing and modeling transmission and combination of signals in cortical networks. The signal dynamics is modeled in terms of diffusion, which allows the information processing undergone between any pair of nodes to be fully characterized in terms of a finite impulse response (FIR) filter. Diffusion without and with time decay are investigated. All filters underlying the cat and macaque cortical organization are found to be of low-pass nature, allowing the cortical signal processing to be summarized in terms of the respective cutoff frequencies (a high cutoff frequency meaning little alteration of signals through their intermixing). Several findings are reported and discussed, including the fact that the incorporation of temporal activity decay tends to provide more diversified cutoff frequencies. Different filtering intensity is observed for each community in those networks. In addition, the brain regions involved in object recognition tend to present the highest cutoff frequencies for both the cat and macaque networks.

Perfect blind restoration of images blurred by multiple filters: theory and efficient algorithms.

PubMed

Harikumar, G; Bresler, Y

1999-01-01

We address the problem of restoring an image from its noisy convolutions with two or more unknown finite impulse response (FIR) filters. We develop theoretical results about the existence and uniqueness of solutions, and show that under some generically true assumptions, both the filters and the image can be determined exactly in the absence of noise, and stably estimated in its presence. We present efficient algorithms to estimate the blur functions and their sizes. These algorithms are of two types, subspace-based and likelihood-based, and are extensions of techniques proposed for the solution of the multichannel blind deconvolution problem in one dimension. We present memory and computation-efficient techniques to handle the very large matrices arising in the two-dimensional (2-D) case. Once the blur functions are determined, they are used in a multichannel deconvolution step to reconstruct the unknown image. The theoretical and practical implications of edge effects, and "weakly exciting" images are examined. Finally, the algorithms are demonstrated on synthetic and real data.

Using indicator plants to assess susceptibility of Californian red fir and white fir to the fir engraver beetle

Treesearch

George T. Ferrell

1986-01-01

Using a Vegetation Drought Index (VDI) for estimating the susceptibility of California red and white firs to the fir engraver beetle (Scolytus venttralis) was evaluated in northern California forests where these true firs (Abies species) occur in mixed conifer and true fir stands. Midway through the summer drought, true fir...

Linear Phase Sharp Transition BPF to Detect Noninvasive Maternal and Fetal Heart Rate.

PubMed

Marchon, Niyan; Naik, Gourish; Pai, K R

2018-01-01

Fetal heart rate (FHR) detection can be monitored using either direct fetal scalp electrode recording (invasive) or by indirect noninvasive technique. Weeks before delivery, the invasive method poses a risk factor to the fetus, while the latter provides accurate fetal ECG (FECG) information which can help diagnose fetal's well-being. Our technique employs variable order linear phase sharp transition (LPST) FIR band-pass filter which shows improved stopband attenuation at higher filter orders. The fetal frequency fiduciary edges form the band edges of the filter characterized by varying amounts of overlap of maternal ECG (MECG) spectrum. The one with the minimum maternal spectrum overlap was found to be optimum with no power line interference and maximum fetal heart beats being detected. The improved filtering is reflected in the enhancement of the performance of the fetal QRS detector (FQRS). The improvement has also occurred in fetal heart rate obtained using our algorithm which is in close agreement with the true reference (i.e., invasive fetal scalp ECG). The performance parameters of the FQRS detector such as sensitivity (Se), positive predictive value (PPV), and accuracy (F 1 ) were found to improve even for lower filter order. The same technique was extended to evaluate maternal QRS detector (MQRS) and found to yield satisfactory maternal heart rate (MHR) results.

Cryogenic bolometric systems

NASA Astrophysics Data System (ADS)

Kangas, Miikka Matias

The big bang, early galaxy formation, the interstellar medium, and high z galaxy cluster evolution are all science objectives that are studied in the far infrared (FIR). The cosmological parameters that describe the universe are encoded in anisotropies in the Cosmic Microwave Background (CMB), and can be extracted from precision subdegree angular resolution FIR maps. Cryogenic bolometers are well suited for these science objectives, and are evolving rapidly today. A cryogenic bolometric system is made up of a few building blocks, which can be modularized or integrated depending on the maturity of the scientific field they are used for. Integration of systems increases with the maturity of the technology. The basic building blocks are the bolometer, the cryogenics, the dewar, the optics, the filters, and electronics. The electronics can be further subdivided into room temperature back-end and cryogenic front-end electronics. The electronics are often partly integrated into the dewar. The dewar is part of the support structure, and only the subkelvin portion the dewar is referred to as cryogenics here. Each of these can be a sophisticated engineering feat on their own, and this dissertation revolves around the development of several of these elements. The microfabrication sequence for a free standing micromesh detector was developed. Polarization preserving photometer optics and filters were constructed and tested. A test dewar mechanical and optical structure was created to test single pixel photometers prior to mounting in the flight dewar. A modular flight dewar capable of holding an array of photometers and adaptable to a number of different cryogenics schemes and detector arrays was engineered and constructed. A zero gravity dilution refrigerator coil was constructed and tested. A corrugated platelet array concept was designed and tested. Metal mesh filter design and fabrication techniques were developed. Kevlar isolator structures were improved to work in subkelvin dewars, and detector modules that mounted the bolometer chips to the photometer tubes were created. These subsystems underwent testing to compare the predicted behavior and actual performance.

Implementing the EuroFIR Document and Data Repositories as accessible resources of food composition information.

PubMed

Unwin, Ian; Jansen-van der Vliet, Martine; Westenbrink, Susanne; Presser, Karl; Infanger, Esther; Porubska, Janka; Roe, Mark; Finglas, Paul

2016-02-15

The EuroFIR Document and Data Repositories are being developed as accessible collections of source documents, including grey literature, and the food composition data reported in them. These Repositories will contain source information available to food composition database compilers when selecting their nutritional data. The Document Repository was implemented as searchable bibliographic records in the Europe PubMed Central database, which links to the documents online. The Data Repository will contain original data from source documents in the Document Repository. Testing confirmed the FoodCASE food database management system as a suitable tool for the input, documentation and quality assessment of Data Repository information. Data management requirements for the input and documentation of reported analytical results were established, including record identification and method documentation specifications. Document access and data preparation using the Repositories will provide information resources for compilers, eliminating duplicated work and supporting unambiguous referencing of data contributing to their compiled data. Copyright © 2014 Elsevier Ltd. All rights reserved.

Recursive Implementations of the Consider Filter

NASA Technical Reports Server (NTRS)

Zanetti, Renato; DSouza, Chris

2012-01-01

One method to account for parameters errors in the Kalman filter is to consider their effect in the so-called Schmidt-Kalman filter. This work addresses issues that arise when implementing a consider Kalman filter as a real-time, recursive algorithm. A favorite implementation of the Kalman filter as an onboard navigation subsystem is the UDU formulation. A new way to implement a UDU consider filter is proposed. The non-optimality of the recursive consider filter is also analyzed, and a modified algorithm is proposed to overcome this limitation.

Rooting cuttings from douglas-fir, white-fir, and California red fir christmas trees

Treesearch

C. M. Blankensop; R. Z. Callaham

1960-01-01

Christmas tree growers in California have asked geneticists to help improve the characteristics of the - wild species they are cultivating. The preferred Christmas trees of California are Shasta red fir (Abies magnifica A. Murr.), white fir (A. concolor (Gord. & Glend.) Lindl.), and Douglas-fir (Pseudotsuga...

Comparison of the Diversity of Basidiomycetes from Dead Wood of the Manchurian fir (Abies holophylla) as Evaluated by Fruiting Body Collection, Mycelial Isolation, and 454 Sequencing.

PubMed

Jang, Yeongseon; Jang, Seokyoon; Min, Mihee; Hong, Joo-Hyun; Lee, Hanbyul; Lee, Hwanhwi; Lim, Young Woon; Kim, Jae-Jin

2015-10-01

In this study, three different methods (fruiting body collection, mycelial isolation, and 454 sequencing) were implemented to determine the diversity of wood-inhabiting basidiomycetes from dead Manchurian fir (Abies holophylla). The three methods recovered similar species richness (26 species from fruiting bodies, 32 species from mycelia, and 32 species from 454 sequencing), but Fisher's alpha, Shannon-Wiener, Simpson's diversity indices of fungal communities indicated fruiting body collection and mycelial isolation displayed higher diversity compared with 454 sequencing. In total, 75 wood-inhabiting basidiomycetes were detected. The most frequently observed species were Heterobasidion orientale (fruiting body collection), Bjerkandera adusta (mycelial isolation), and Trichaptum fusco-violaceum (454 sequencing). Only two species, Hymenochaete yasudae and Hypochnicium karstenii, were detected by all three methods. This result indicated that Manchurian fir harbors a diverse basidiomycetous fungal community and for complete estimation of fungal diversity, multiple methods should be used. Further studies are required to understand their ecology in the context of forest ecosystems.

Non-transmissible Sendai virus vector encoding c-myc suppressor FBP-interacting repressor for cancer therapy

PubMed Central

Matsushita, Kazuyuki; Shimada, Hideaki; Ueda, Yasuji; Inoue, Makoto; Hasegawa, Mamoru; Tomonaga, Takeshi; Matsubara, Hisahiro; Nomura, Fumio

2014-01-01

AIM: To investigate a novel therapeutic strategy to target and suppress c-myc in human cancers using far up stream element (FUSE)-binding protein-interacting repressor (FIR). METHODS: Endogenous c-Myc suppression and apoptosis induction by a transient FIR-expressing vector was examined in vivo via a HA-tagged FIR (HA-FIR) expression vector. A fusion gene-deficient, non-transmissible, Sendai virus (SeV) vector encoding FIR cDNA, SeV/dF/FIR, was prepared. SeV/dF/FIR was examined for its gene transduction efficiency, viral dose dependency of antitumor effect and apoptosis induction in HeLa (cervical squamous cell carcinoma) cells and SW480 (colon adenocarcinoma) cells. Antitumor efficacy in a mouse xenograft model was also examined. The molecular mechanism of the anti-tumor effect and c-Myc suppression by SeV/dF/FIR was examined using Spliceostatin A (SSA), a SAP155 inhibitor, or SAP155 siRNA which induce c-Myc by increasing FIR∆exon2 in HeLa cells. RESULTS: FIR was found to repress c-myc transcription and in turn the overexpression of FIR drove apoptosis through c-myc suppression. Thus, FIR expressing vectors are potentially applicable for cancer therapy. FIR is alternatively spliced by SAP155 in cancer cells lacking the transcriptional repression domain within exon 2 (FIR∆exon2), counteracting FIR for c-Myc protein expression. Furthermore, FIR forms a complex with SAP155 and inhibits mutual well-established functions. Thus, both the valuable effects and side effects of exogenous FIR stimuli should be tested for future clinical application. SeV/dF/FIR, a cytoplasmic RNA virus, was successfully prepared and showed highly efficient gene transduction in in vivo experiments. Furthermore, in nude mouse tumor xenograft models, SeV/dF/FIR displayed high antitumor efficiency against human cancer cells. SeV/dF/FIR suppressed SSA-activated c-Myc. SAP155 siRNA, potentially produces FIR∆exon2, and led to c-Myc overexpression with phosphorylation at Ser62. HA-FIR suppressed endogenous c-Myc expression and induced apoptosis in HeLa and SW480 cells. A c-myc transcriptional suppressor FIR expressing SeV/dF/FIR showed high gene transduction efficiency with significant antitumor effects and apoptosis induction in HeLa and SW480 cells. CONCLUSION: SeV/dF/FIR showed strong tumor growth suppression with no significant side effects in an animal xenograft model, thus SeV/dF/FIR is potentially applicable for future clinical cancer treatment. PMID:24764668

Price projections for selected grades of Douglas-fir, coast hem-fir, inland hem-fir, and ponderosa pine lumber.

Treesearch

Richard W. Haynes; Roger D. Fight

1992-01-01

Grade-specific price projections were developed for Douglas-fir, coast hem-fir, inland hem-fir, and ponderosa pine lumber. These grade-specific price projections can be used in evaluating management practices that will affect the quality of saw logs produced under various management regimes.

Weather and tree growth associated with white fir mortality caused by fir engraver and roundheaded fir borer

Treesearch

George T. Ferrell; Ralph C. Hall

1975-01-01

White fir (Abides concolor [Cord. & Glend.] Lindl.) stands in Western North America periodically suffer extensive tree mortality caused by outbreaks of the fir engraver bark beetle (Scolytus ventralis Lec.). The cambial zone of the boles infested by S. ventralis is also colonized by the roundheaded fir borer...

Sensor fusion for structural tilt estimation using an acceleration-based tilt sensor and a gyroscope

NASA Astrophysics Data System (ADS)

Liu, Cheng; Park, Jong-Woong; Spencer, B. F., Jr.; Moon, Do-Soo; Fan, Jiansheng

2017-10-01

A tilt sensor can provide useful information regarding the health of structural systems. Most existing tilt sensors are gravity/acceleration based and can provide accurate measurements of static responses. However, for dynamic tilt, acceleration can dramatically affect the measured responses due to crosstalk. Thus, dynamic tilt measurement is still a challenging problem. One option is to integrate the output of a gyroscope sensor, which measures the angular velocity, to obtain the tilt; however, problems arise because the low-frequency sensitivity of the gyroscope is poor. This paper proposes a new approach to dynamic tilt measurements, fusing together information from a MEMS-based gyroscope and an acceleration-based tilt sensor. The gyroscope provides good estimates of the tilt at higher frequencies, whereas the acceleration measurements are used to estimate the tilt at lower frequencies. The Tikhonov regularization approach is employed to fuse these measurements together and overcome the ill-posed nature of the problem. The solution is carried out in the frequency domain and then implemented in the time domain using FIR filters to ensure stability. The proposed method is validated numerically and experimentally to show that it performs well in estimating both the pseudo-static and dynamic tilt measurements.

Nanotechnology Infrared Optics for Astronomy Missions

NASA Technical Reports Server (NTRS)

Smith, Howard A.; Stringfellow, Guy (Technical Monitor)

2002-01-01

The program "Nanotechnology Infrared Optics for Astronomy Missions" will design and develop new, nanotechnology techniques for infrared optical devices suitable for use in NASA space missions. The proposal combines expertise from the Smithsonian Astrophysical Observatory, the Naval Research Laboratory, the Goddard Space Flight Center, and the Physics Department at the Queen Mary and Westfield College in London, now relocated to the University of Cardiff, Cardiff, Wales. The method uses individually tailored metal grids, and layered stacks of metal mesh grids, both inductive (free-standing) and capacitive (substrate-mounted), to produce various kinds of filters. The program has the following goals: (1) Model FIR filter properties using electric-circuit analogs, and near-field, EM diffraction calculations; (2) Prototype fabrication of meshes on various substrates, with various materials, and of various dimensions; (3) Test of filter prototypes, and iterate with the modeling programs; (4) Travel to related sites, including trips to Washington, D.C. (location of NRL and GSFC), London (location of QMW), Cardiff, Wales, and Rome (location of ISO PMS project headquarters); (5) Produce ancillary science, including publication of both testing on mesh performance and infrared astronomical science.

Nanotechnology Infrared Optics for Astronomy Missions

NASA Technical Reports Server (NTRS)

Smith, Howard A.; Frogel, Jay (Technical Monitor)

2003-01-01

The program "Nanotechnology Infrared Optics for Astronomy Missions" will design and develop new, nanotechnology techniques for infrared optical devices suitable for use in NASA space missions. The proposal combines expertise from the Smithsonian Astrophysical Observatory, the Naval Research Laboratory, the Goddard Space Flight Center, and the Physics Department at the Queen Mary and Westfield College in London, now relocated to the University of Cardiff, Cardiff, Wales. The method uses individually tailored metal grids and layered stacks of metal mesh grids, both inductive (freestanding) and capacitive (substrate-mounted), to produce various kinds of filters. The program has the following goals: 1) Model FIR filter properties using electric-circuit analogs and near-field, EM diffraction calculations. 2) Prototype fabrication of meshes on various substrates, with various materials, and of various dimensions. 3) Test filter prototypes and iterate with the modeling programs. 4) Travel to related sites, including trips to Washington, D.C. (location of NRL and GSFC), London (location of QMW), Cardiff, Wales, and Rome (location of ISO PMS project headquarters). 5) Produce ancillary science, including both publication of testing on mesh performance and infrared astronomical science.

Adaptive Identification and Control of Flow-Induced Cavity Oscillations

NASA Technical Reports Server (NTRS)

Kegerise, M. A.; Cattafesta, L. N.; Ha, C.

2002-01-01

Progress towards an adaptive self-tuning regulator (STR) for the cavity tone problem is discussed in this paper. Adaptive system identification algorithms were applied to an experimental cavity-flow tested as a prerequisite to control. In addition, a simple digital controller and a piezoelectric bimorph actuator were used to demonstrate multiple tone suppression. The control tests at Mach numbers of 0.275, 0.40, and 0.60 indicated approx. = 7dB tone reductions at multiple frequencies. Several different adaptive system identification algorithms were applied at a single freestream Mach number of 0.275. Adaptive finite-impulse response (FIR) filters of orders up to N = 100 were found to be unsuitable for modeling the cavity flow dynamics. Adaptive infinite-impulse response (IIR) filters of comparable order better captured the system dynamics. Two recursive algorithms, the least-mean square (LMS) and the recursive-least square (RLS), were utilized to update the adaptive filter coefficients. Given the sample-time requirements imposed by the cavity flow dynamics, the computational simplicity of the least mean squares (LMS) algorithm is advantageous for real-time control.

Silvics of grand fir

Treesearch

Marvin W. Foiles

1959-01-01

Grand fir (Abies grandis) is one of the two balsam firs found in the northern Rocky Mountain region and one of seven in the Pacific Northwest. Except in the southern part of its range, where it is often confused with white fir (Abies concolor), it is distinguished from other firs in its range by its needles, which are distinctly two-ranked. Grand fir differs...

Growth classification systems for red fir and white fir in northern California

Treesearch

George T. Ferrell

1983-01-01

Selected crown and bole characteristics were predictor variables in growth classification equations developed for California red fir, Shasta red fir, and white fir in northern California. Individual firs were classified on the basis of percent basal area increment (PCTBAI ) as Class 1 (≤ 1 pct), Class 2 (> 1 pct and ≤ 3 pct), or Class 3 (> 3...

Fir dwarf mistletoe (FIDL).

Treesearch

Gregory M. Filip; Jerome S. Beatty; Robert L. Mathiasen

2000-01-01

Fir dwarf mistletoe (Arceuthobium abietinum Engelmann ex Munz) is a common and damaging parasite of white fir (Abies concolor (Gord. & Glend.) Lindl. ex Hildebr.), grand fir (Abies grandis (Dougl. ex D. Don) Lindl.), and California red fir (A. magnifica A. Murr.) in the western...

Damage from wind and other causes in mixed white fir-red fir stands adjacent to clearcuttings

Treesearch

Donald T. Gordon

1973-01-01

Damage to timber surrounding clearcuttings and in one light selection cutting in mixed white fir-red fir stands was monitored for 6 years in northeastern California. In some years, bark beetles apparently killed more trees than did wind damage, but in two of the study years, severe wind storms caused much damage. One storm produced mainly break-age, apparently...

Radial growth of grand fir and Douglas-fir 10 years after defoliation by the Douglas-fir tussock moth in the Blue Mountains outbreak.

Treesearch

Boyd E. Wickman

1986-01-01

Radial-growth recovery related to amount of tree defoliation was measured 10 years after a severe outbreak of Douglas-fir tussock moth (Orgyia pseudotsugata (McDunnough). For the period 1978-82, growth of qrand fir surpassed and was significantly greater than in the preoutbreak period, 1968-72. Douglas-fir growth during the postoutbreak period...

Reconsidering price projections for selected grades of Douglas-fir, coast hem-fir, inland hem-fir, and ponderosa pine lumber.

Treesearch

Richard W. Haynes; Roger D. Fight

2004-01-01

Grade-specific price projections were once again developed for Douglas-fir, coast hem-fir, inland hem-fir, and ponderosa pine lumber. These grade-specific price projections can be used to demonstrate the returns to land management of practices that lead to high-quality logs that produce a larger proportion of high grades of lumber. The price ratios among low, medium,...

Douglas-fir tussock moth- and Douglas-fir beetle-caused mortality in a ponderosa pine/Douglas-fir forest in the Colorado Front Range, USA

Treesearch

Jose F. Negron; Ann M. Lynch; Willis C. Schaupp; Vladimir Bocharnikov

2014-01-01

An outbreak of the Douglas-fir tussock moth, Orgyia pseudotsugata McDunnough, occurred in the South Platte River drainage on the Pike-San Isabel National Forest in the Colorado Front Range attacking Douglas-fir, Pseudotsuga menziesii (Mirb.) Franco. Stocking levels, species composition, and tree size in heavily and lightly defoliated stands were similar. Douglas-fir...

AmeriFlux CA-Na1 New Brunswick - 1967 Balsam Fir - Nashwaak Lake Site 01 (Mature balsam fir forest)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bourque, Charles P.-A.

This is the AmeriFlux version of the carbon flux data for the site CA-Na1 New Brunswick - 1967 Balsam Fir - Nashwaak Lake Site 01 (Mature balsam fir forest). Site Description - immature balsam fir forest

Remote pedestrians detection at night time in FIR Image using contrast filtering and locally projected region based CNN

NASA Astrophysics Data System (ADS)

Kim, Taehwan; Kim, Sungho

2017-02-01

This paper presents a novel method to detect the remote pedestrians. After producing the human temperature based brightness enhancement image using the temperature data input, we generates the regions of interest (ROIs) by the multiscale contrast filtering based approach including the biased hysteresis threshold and clustering, remote pedestrian's height, pixel area and central position information. Afterwards, we conduct local vertical and horizontal projection based ROI refinement and weak aspect ratio based ROI limitation to solve the problem of region expansion in the contrast filtering stage. Finally, we detect the remote pedestrians by validating the final ROIs using transfer learning with convolutional neural network (CNN) feature, following non-maximal suppression (NMS) with strong aspect ratio limitation to improve the detection performance. In the experimental results, we confirmed that the proposed contrast filtering and locally projected region based CNN (CFLP-CNN) outperforms the baseline method by 8% in term of logaveraged miss rate. Also, the proposed method is more effective than the baseline approach and the proposed method provides the better regions that are suitably adjusted to the shape and appearance of remote pedestrians, which makes it detect the pedestrian that didn't find in the baseline approach and are able to help detect pedestrians by splitting the people group into a person.

77 FR 57578 - Renewal of Approved Information Collection

Federal Register 2010, 2011, 2012, 2013, 2014

2012-09-18

... necessary to implement two provisions of the Federal Cave Resources Protection Act-- one which requires... Information Relay Service (FIRS) at 1-800-877-8339, to leave a message for Mr. Goodbar. You may also review... with the Federal Cave Resources Protection Act (16 U.S.C. 4301- 4310). Frequency of Collection: On...

Adjustable Nyquist-rate System for Single-Bit Sigma-Delta ADC with Alternative FIR Architecture

NASA Astrophysics Data System (ADS)

Frick, Vincent; Dadouche, Foudil; Berviller, Hervé

2016-09-01

This paper presents a new smart and compact system dedicated to control the output sampling frequency of an analogue-to-digital converters (ADC) based on single-bit sigma-delta (ΣΔ) modulator. This system dramatically improves the spectral analysis capabilities of power network analysers (power meters) by adjusting the ADC's sampling frequency to the input signal's fundamental frequency with a few parts per million accuracy. The trade-off between straightforwardness and performance that motivated the choice of the ADC's architecture are preliminary discussed. It particularly comes along with design considerations of an ultra-steep direct-form FIR that is optimised in terms of size and operating speed. Thanks to compact standard VHDL language description, the architecture of the proposed system is particularly suitable for application-specific integrated circuit (ASIC) implementation-oriented low-power and low-cost power meter applications. Field programmable gate array (FPGA) prototyping and experimental results validate the adjustable sampling frequency concept. They also show that the system can perform better in terms of implementation and power capabilities compared to dedicated IP resources.

Beyond reducing fire hazard: fuel treatment impacts on overstory tree survival

USGS Publications Warehouse

Collins, Brandon M.; Das, Adrian J.; Battles, John J.; Fry, Danny L.; Krasnow, Kevin D.; Stephens, Scott L.

2014-01-01

Fuel treatment implementation in dry forest types throughout the western United States is likely to increase in pace and scale in response to increasing incidence of large wildfires. While it is clear that properly implemented fuel treatments are effective at reducing hazardous fire potential, there are ancillary ecological effects that can impact forest resilience either positively or negatively depending on the specific elements examined, as well as treatment type, timing, and intensity. In this study, we use overstory tree growth responses, measured seven years after the most common fuel treatments, to estimate forest health. Across the five species analyzed, observed mortality and future vulnerability were consistently low in the mechanical-only treatment. Fire-only was similar to the control for all species except Douglas-fir, while mechanical-plus-fire had high observed mortality and future vulnerability for white fir and sugar pine. Given that overstory trees largely dictate the function of forests and services they provide (e.g., wildlife habitat, carbon sequestration, soil stability) these results have implications for understanding longer-term impacts of common fuel treatments on forest resilience.

Progress on FIR interferometry and Thomson Scattering measurements on HIT-SI3

NASA Astrophysics Data System (ADS)

Everson, Christopher; Jarboe, Thomas; Morgan, Kyle

2017-10-01

Spatially resolved measurements of the electron temperature (Te) and density (ne) will be fundamental in assessing the degree to which HIT-SI3 demonstrates closed magnetic flux and energy confinement. Further, electron temperature measurements have not yet been made on an inductively-driven spheromak. Far infrared (FIR) interferometer and Thomson Scattering (TS) systems have been installed on the HIT-SI3 spheromak. The TS system currently implemented on HIT-SI3 was originally designed for other magnetic confinement experiments, and progress continues toward modifying and optimizing for HIT-SI3 plasmas. Initial results suggest that the electron temperature is of order 10 eV. Plans to modify the TS system to provide more sensitivity and accuracy at low temperatures are presented. The line-integrated ne is measured on one chord by the FIR interferometer, with densities near 5x1019 m-3. Four cylindrical volumes have been added to the HIT-SI3 apparatus to enhance passive pumping. It is hoped that this will allow for more control of the density during the 2 ms discharges. Density measurements from before and after the installation of the passive pumping volumes are presented for comparison.

Fir Engraver (FIDL)

Treesearch

George T. Ferrell

1986-01-01

The fir engraver, Scolytus ventralis LeConte, belongs to the family of insects called bark beetles, which live between the bark and wood of host trees. A wide-ranging, native beetle, the fir engraver attacks most species of fir in the Western United States. Epidemics can cause severe tree mortality. From 1977 to 1978, for example, the fir engraver killed an estimated 1...

Heart Rots of Red and White Firs

Treesearch

J.W. Kimmey; H.H. Jr. Bynum

1961-01-01

Heart rots, caused by fungi that attack the heartwood of living trees, are responsible for the greatest volume loss sustained by California red fir (Abies magnifica A. Murr.) and white fir (A. concolor (Gord. and Glend.) Lindl.). These two firs comprise 25 percent of the commercial timber of California. More than 13 percent of the volume in these firs is useless cull...

The identification of Douglas-fir wood

Treesearch

Forest Products Laboratory (U.S.)

1963-01-01

Douglas-fir is one of the largest, most abundant and widely distributed species of trees native to North America, and next to the southern yellow pines, it is cut in the greatest quantities of any wood of commercial importance. It belongs to the coniferous family and is, therefore, a softwood. Other names for Douglas -fir are red fir, yellow fir, Oregon pine, Puget...

Weather, logging, and tree growth associated with fir engraver attack scars in white fir

Treesearch

George T. Ferrell

1973-01-01

The boles of 32 recently killed, and 41 living, white fir were examined for embedded fir engraver (Scolytus ventralis) attack scars. Of 287 scars found in annual rings for the years 1934-69, only 2 to 3 percent represented reproductively successful attacks. Trends in scar abundance were directly correlated with trends in white fir killed by ...

Concomitant expression of far upstream element (FUSE) binding protein (FBP) interacting repressor (FIR) and its splice variants induce migration and invasion of non-small cell lung cancer (NSCLC) cells.

PubMed

Müller, Benedikt; Bovet, Michael; Yin, Yi; Stichel, Damian; Malz, Mona; González-Vallinas, Margarita; Middleton, Alistair; Ehemann, Volker; Schmitt, Jennifer; Muley, Thomas; Meister, Michael; Herpel, Esther; Singer, Stephan; Warth, Arne; Schirmacher, Peter; Drasdo, Dirk; Matthäus, Franziska; Breuhahn, Kai

2015-11-01

Transcription factors integrate a variety of oncogenic input information, facilitate tumour growth and cell dissemination, and therefore represent promising therapeutic target structures. Because over-expression of DNA-interacting far upstream element binding protein (FBP) supports non-small cell lung cancer (NSCLC) migration, we asked whether its repressor, FBP-interacting repressor (FIR) is functionally inactivated and how FIR might affect NSCLC cell biology. Different FIR splice variants were highly expressed in the majority of NSCLCs, with the highest levels in tumours carrying genomic gains of chromosome 8q24.3, which contained the FIR gene locus. Nuclear FIR expression was significantly enriched at the invasion front of primary NSCLCs, but this did not correlate with tumour cell proliferation. FIR accumulation was associated with worse patient survival and tumour recurrence; in addition, FIR over-expression significantly correlated with lymph node metastasis in squamous cell carcinomas (SCCs). In vitro, we applied newly developed methods and modelling approaches for the quantitative and time-resolved description of the pro-migratory and pro-invasive capacities of SCC cells. siRNA-mediated silencing of all FIR variants significantly reduced the speed and directional movement of tumour cells in all phases of migration. Furthermore, sprouting efficiency and single cell invasiveness were diminished following FIR inhibition. Interestingly, the silencing of FIR isoforms lacking exon 2 (FIR(Δexon2)) alone was sufficient to reduce lateral migration and invasion. In summary, by using scale-spanning data derived from primary human tissues, quantitative cellular analyses and mathematical modelling, we have demonstrated that concomitant over-expression of FIR and its splice variants drives NSCLC migration and dissemination. Copyright © 2015 Pathological Society of Great Britain and Ireland. Published by John Wiley & Sons, Ltd.

Efficient Scalable Median Filtering Using Histogram-Based Operations.

PubMed

Green, Oded

2018-05-01

Median filtering is a smoothing technique for noise removal in images. While there are various implementations of median filtering for a single-core CPU, there are few implementations for accelerators and multi-core systems. Many parallel implementations of median filtering use a sorting algorithm for rearranging the values within a filtering window and taking the median of the sorted value. While using sorting algorithms allows for simple parallel implementations, the cost of the sorting becomes prohibitive as the filtering windows grow. This makes such algorithms, sequential and parallel alike, inefficient. In this work, we introduce the first software parallel median filtering that is non-sorting-based. The new algorithm uses efficient histogram-based operations. These reduce the computational requirements of the new algorithm while also accessing the image fewer times. We show an implementation of our algorithm for both the CPU and NVIDIA's CUDA supported graphics processing unit (GPU). The new algorithm is compared with several other leading CPU and GPU implementations. The CPU implementation has near perfect linear scaling with a speedup on a quad-core system. The GPU implementation is several orders of magnitude faster than the other GPU implementations for mid-size median filters. For small kernels, and , comparison-based approaches are preferable as fewer operations are required. Lastly, the new algorithm is open-source and can be found in the OpenCV library.

Disturbed alternative splicing of FIR (PUF60) directed cyclin E overexpression in esophageal cancers.

PubMed

Ogura, Yukiko; Hoshino, Tyuji; Tanaka, Nobuko; Ailiken, Guzhanuer; Kobayashi, Sohei; Kitamura, Kouichi; Rahmutulla, Bahityar; Kano, Masayuki; Murakami, Kentarou; Akutsu, Yasunori; Nomura, Fumio; Itoga, Sakae; Matsubara, Hisahiro; Matsushita, Kazuyuki

2018-05-01

Overexpression of alternative splicing of far upstream element binding protein 1 (FUBP1) interacting repressor (FIR; poly(U) binding splicing factor 60 [PUF60]) and cyclin E were detected in esophageal squamous cell carcinomas (ESCC). Accordingly, the expression of FBW7 was examined by which cyclin E is degraded as a substrate via the proteasome system. Expectedly, FBW7 expression was decreased significantly in ESCC. Conversely, c-myc gene transcriptional repressor FIR (alias PUF60; U2AF-related protein) and its alternative splicing variant form (FIRΔexon2) were overexpressed in ESCC. Further, anticancer drugs (cis-diaminedichloroplatinum/cisplatin [CDDP] or 5-fluorouracil [5-FU]) and knockdown of FIR by small interfering RNA (siRNA) increased cyclin E while knockdown of FIRΔexon2 by siRNA decreased cyclin E expression in ESCC cell lines (TE1, TE2, and T.Tn) or cervical SCC cells (HeLa cells). Especially, knockdown of SAP155 (SF3b1), a splicing factor required for proper alternative splicing of FIR pre-mRNA, decreased cyclin E. Therefore, disturbed alternative splicing of FIR generated FIR/FIRΔexon2 with cyclin E overexpression in esophageal cancers, indicating that SAP155 siRNA potentially rescued FBW7 function by reducing expression of FIR and/or FIRΔexon2. Remarkably, Three-dimensional structure analysis revealed the hypothetical inhibitory mechanism of FBW7 function by FIR/FIRΔexon2, a novel mechanism of cyclin E overexpression by FIR/FIRΔexon2-FBW7 interaction was discussed. Clinically, elevated FIR expression potentially is an indicator of the number of lymph metastases and anti-FIR/FIRΔexon2 antibodies in sera as cancer diagnosis, indicating chemical inhibitors of FIR/FIRΔexon2-FBW7 interaction could be potential candidate drugs for cancer therapy. In conclusion, elevated cyclin E expression was, in part, induced owing to potential FIR/FIRΔexon2-FBW7 interaction in ESCC.

Far infrared promotes wound healing through activation of Notch1 signaling.

PubMed

Hsu, Yung-Ho; Lin, Yuan-Feng; Chen, Cheng-Hsien; Chiu, Yu-Jhe; Chiu, Hui-Wen

2017-11-01

The Notch signaling pathway is critically involved in cell proliferation, differentiation, development, and homeostasis. Far infrared (FIR) has an effect that promotes wound healing. However, the underlying molecular mechanisms are unclear. In the present study, we employed in vivo and HaCaT (a human skin keratinocyte cell line) models to elucidate the role of Notch1 signaling in FIR-promoted wound healing. We found that FIR enhanced keratinocyte migration and proliferation. FIR induced the Notch1 signaling pathway in HaCaT cells and in a microarray dataset from the Gene Expression Omnibus database. We next determined the mRNA levels of NOTCH1 in paired normal and wound skin tissues derived from clinical patients using the microarray dataset and Ingenuity Pathway Analysis software. The result indicated that the Notch1/Twist1 axis plays important roles in wound healing and tissue repair. In addition, inhibiting Notch1 signaling decreased the FIR-enhanced proliferation and migration. In a full-thickness wound model in rats, the wounds healed more rapidly and the scar size was smaller in the FIR group than in the light group. Moreover, FIR could increase Notch1 and Delta1 in skin tissues. The activation of Notch1 signaling may be considered as a possible mechanism for the promoting effect of FIR on wound healing. FIR stimulates keratinocyte migration and proliferation. Notch1 in keratinocytes has an essential role in FIR-induced migration and proliferation. NOTCH1 promotes TWIST1-mediated gene expression to assist wound healing. FIR might promote skin wound healing in a rat model. FIR stimulates keratinocyte migration and proliferation. Notch1 in keratinocytes has an essential role in FIR-induced migration and proliferation. NOTCH1 promotes TWIST1-mediated gene expression to assist wound healing. FIR might promote skin wound healing in a rat model.

Silvical characteristics of balsam fir (Abies balsamea)

Treesearch

Arthur C. Hart

1959-01-01

Balsam fir takes its name from the Latin word for balm. Some people know the tree as the Balm-of-Gilead fir. It has also been called the blister fir, because of the bark blisters that yield Canada balsam, a resin that is used for, among other things, mounting microscope slides. The needles of balsam fir have a spicy aroma that Donald Culross Peattie has called "...

Predicting susceptibility of white fir during a drought-associated outbreak of the fir engraver, Scolytus centralis, in California

Treesearch

G.T. Ferrell; W.J. Otrosina; C.J. DeMars

1994-01-01

Phenotypic traits were compared with a vigor (growth efficiency) index for accuracy in predicting susceptibility of white fir, Abies concolor (Gord. & Glend.) Lindl., during a drought-associated outbreak of the fir engraver, Scolytus centralis LeC., in the central Sierra Nevada at Lake Tahoe, California.Predictor variables were estimated for 633 firs in six forest...

Seed maturity in white fir and red fir

Treesearch

William W. Oliver

1974-01-01

White fir and red fir seed collected over a 2-month period in northern California was tested for germination of fresh and stratified seed. Ratio of embryo length to embryo cavity length was found to be the most useful index of seed maturity for white and red fir. Cone specific gravity also was correlated with nearly all measures of seed germination. Data suggest that...

Differential susceptibility of white fir provenances to the fir engraver and its fungal symbiont in northern California

Treesearch

G.T. Ferrell; W.J. Otrosina

1996-01-01

The fir engraver, Scolytus ventralis LeC., attacks white fir, Abies concolor (Gord. and Glend.) Lindl., and other true firs, Abies spp., in western North America. The biology, attack behavior, and ecology of this bark beetle were recently summarized by Berryman and Ferrell (1988). During the summer flight season, the attacking beetles bore into the cambial zone of...

Planck's view on the spectrum of the Sunyaev-Zeldovich effect

NASA Astrophysics Data System (ADS)

Erler, Jens; Basu, Kaustuv; Chluba, Jens; Bertoldi, Frank

2018-05-01

We present a detailed analysis of the stacked frequency spectrum of a large sample of galaxy clusters using Planck data, together with auxiliary data from the AKARI and IRAS missions. Our primary goal is to search for the imprint of relativistic corrections to the thermal Sunyaev-Zeldovich effect (tSZ) spectrum, which allow to measure the temperature of the intracluster medium. We remove Galactic and extragalactic foregrounds with a matched filtering technique, which is validated using simulations with realistic mock data sets. The extracted spectra show the tSZ signal at high significance and reveal an additional far-infrared (FIR) excess, which we attribute to thermal emission from the galaxy clusters themselves. This excess FIR emission from clusters is accounted for in our spectral model. We are able to measure the tSZ relativistic corrections at 2.2σ by constraining the mean temperature of our cluster sample to 4.4^{+2.1}_{-2.0} keV. We repeat the same analysis on a subsample containing only the 100 hottest clusters, for which we measure the mean temperature to be 6.0^{+3.8}_{-2.9} keV, corresponding to 2.0σ. The temperature of the emitting dust grains in our FIR model is constrained to ≃20 K, consistent with previous studies. Control for systematic biases is done by fitting mock clusters, from which we also show that using the non-relativistic spectrum for SZ signal extraction will lead to a bias in the integrated Compton parameter Y, which can be up to 14% for the most massive clusters. We conclude by providing an outlook for the upcoming CCAT-prime telescope, which will improve upon Planck with lower noise and better spatial resolution.

Demonstrating a New Census of Infrared Galaxies with ALMA (DANCING-ALMA). I. FIR Size and Luminosity Relation at z = 0-6 Revealed with 1034 ALMA Sources

NASA Astrophysics Data System (ADS)

Fujimoto, Seiji; Ouchi, Masami; Shibuya, Takatoshi; Nagai, Hiroshi

2017-11-01

We present the large statistics of the galaxy effective radius R e in the rest-frame far-infrared (FIR) wavelength {R}{{e}({FIR})} obtained from 1627 Atacama Large Millimeter/submillimeter Array (ALMA) 1 mm band maps that become public by 2017 July. Our ALMA sample consists of 1034 sources with the star formation rate ˜ 100{--}1000 {M}⊙ {{yr}}-1 and the stellar mass ˜ {10}10{--}{10}11.5 {M}⊙ at z = 0-6. We homogeneously derive {R}{{e}({FIR})} and FIR luminosity L FIR of our ALMA sources via the uv-visibility method with the exponential disk model, carefully evaluating selection and measurement incompletenesses by realistic Monte-Carlo simulations. We find that there is a positive correlation between {R}{{e}({FIR})} and L FIR at the >99% significance level. The best-fit power-law function, {R}{{e}({FIR})}\\propto {L}{FIR}α , provides α =0.28+/- 0.07, and shows that {R}{{e}({FIR})} at a fixed L FIR decreases toward high redshifts. The best-fit α and the redshift evolution of {R}{{e}({FIR})} are similar to those of R e in the rest-frame UV (optical) wavelength {R}{{e}({UV})} ({R}{{e}({Opt}.)}) revealed by Hubble Space Telescope (HST) studies. We identify that our ALMA sources have significant trends of {R}{{e}({FIR})}≲ {R}{{e}({UV})} and {R}{{e}({Opt}.)}, which suggests that the dusty starbursts take place in compact regions. Moreover, {R}{{e}({FIR})} of our ALMA sources is comparable to {R}{{e}({Opt}.)} of quiescent galaxies at z ˜ 1-3 as a function of stellar mass, supporting the evolutionary connection between these two galaxy populations. We also investigate rest-frame UV and optical morphologies of our ALMA sources with deep HST images, and find that ˜30%-40% of our ALMA sources are classified as major mergers. This indicates that dusty starbursts are triggered by not only the major mergers but also the other mechanism(s).

Arithmetic Circuit Verification Based on Symbolic Computer Algebra

NASA Astrophysics Data System (ADS)

Watanabe, Yuki; Homma, Naofumi; Aoki, Takafumi; Higuchi, Tatsuo

This paper presents a formal approach to verify arithmetic circuits using symbolic computer algebra. Our method describes arithmetic circuits directly with high-level mathematical objects based on weighted number systems and arithmetic formulae. Such circuit description can be effectively verified by polynomial reduction techniques using Gröbner Bases. In this paper, we describe how the symbolic computer algebra can be used to describe and verify arithmetic circuits. The advantageous effects of the proposed approach are demonstrated through experimental verification of some arithmetic circuits such as multiply-accumulator and FIR filter. The result shows that the proposed approach has a definite possibility of verifying practical arithmetic circuits.

Chapter 7. Additional studies using CFIRP treatments: Douglas-fir genetics and ambrosia beetle log colonization.

Treesearch

Chris C. Maguire; W. Thomas Adams; Rick G. Kelsey

2005-01-01

As highlighted in previous chapters, the primary biological objectives of CFIRP were to assess impacts of diverse silvicultural treatments on vegetation structure and growth and on the abundance and diversity of wildlife. Stand conditions resulting from implementation of the CFIRP research design, however, provided for the overlay of additional research projects that...

Stand dynamics after variable-retention harvesting in mature Douglas-fir forests of Western North America.

Treesearch

D.A. Maguire; D.B. Mainwaring; C.B. Halpern

2006-01-01

Variable-retention has been proposed as a way to mitigate the effects of timber harvest on biological diversity, particularly lateseral species (FRANKLIN et al., 1997). In the context of silvicultural systems, variable retention harvests represent a regeneration cut because the primary objective is to regenerate the stand without clearcutting. In its implementation,...

Using Scientific Information to Develop Management Strategies for Commercial Redwood Timberlands

Treesearch

Jeffrey C. Barrett

2007-01-01

In 1999, PALCO (Pacific Lumber Company), a private landowner, and the state and federal governments agreed to implement a unique Habitat Conservation Plan (HCP) on 89,000 hectares of commercial redwood and Douglas-fir timberlands in Humboldt County, California. The aquatics portion of the PALCO HCP contains a set of "interim" conservation strategies developed...

Reconstructing the calibrated strain signal in the Advanced LIGO detectors

NASA Astrophysics Data System (ADS)

Viets, A. D.; Wade, M.; Urban, A. L.; Kandhasamy, S.; Betzwieser, J.; Brown, Duncan A.; Burguet-Castell, J.; Cahillane, C.; Goetz, E.; Izumi, K.; Karki, S.; Kissel, J. S.; Mendell, G.; Savage, R. L.; Siemens, X.; Tuyenbayev, D.; Weinstein, A. J.

2018-05-01

Advanced LIGO’s raw detector output needs to be calibrated to compute dimensionless strain h(t) . Calibrated strain data is produced in the time domain using both a low-latency, online procedure and a high-latency, offline procedure. The low-latency h(t) data stream is produced in two stages, the first of which is performed on the same computers that operate the detector’s feedback control system. This stage, referred to as the front-end calibration, uses infinite impulse response (IIR) filtering and performs all operations at a 16 384 Hz digital sampling rate. Due to several limitations, this procedure currently introduces certain systematic errors in the calibrated strain data, motivating the second stage of the low-latency procedure, known as the low-latency gstlal calibration pipeline. The gstlal calibration pipeline uses finite impulse response (FIR) filtering to apply corrections to the output of the front-end calibration. It applies time-dependent correction factors to the sensing and actuation components of the calibrated strain to reduce systematic errors. The gstlal calibration pipeline is also used in high latency to recalibrate the data, which is necessary due mainly to online dropouts in the calibrated data and identified improvements to the calibration models or filters.

Novel mathematical algorithm for pupillometric data analysis.

PubMed

Canver, Matthew C; Canver, Adam C; Revere, Karen E; Amado, Defne; Bennett, Jean; Chung, Daniel C

2014-01-01

Pupillometry is used clinically to evaluate retinal and optic nerve function by measuring pupillary response to light stimuli. We have developed a mathematical algorithm to automate and expedite the analysis of non-filtered, non-calculated pupillometric data obtained from mouse pupillary light reflex recordings, obtained from dynamic pupillary diameter recordings following exposure of varying light intensities. The non-filtered, non-calculated pupillometric data is filtered through a low pass finite impulse response (FIR) filter. Thresholding is used to remove data caused by eye blinking, loss of pupil tracking, and/or head movement. Twelve physiologically relevant parameters were extracted from the collected data: (1) baseline diameter, (2) minimum diameter, (3) response amplitude, (4) re-dilation amplitude, (5) percent of baseline diameter, (6) response time, (7) re-dilation time, (8) average constriction velocity, (9) average re-dilation velocity, (10) maximum constriction velocity, (11) maximum re-dilation velocity, and (12) onset latency. No significant differences were noted between parameters derived from algorithm calculated values and manually derived results (p ≥ 0.05). This mathematical algorithm will expedite endpoint data derivation and eliminate human error in the manual calculation of pupillometric parameters from non-filtered, non-calculated pupillometric values. Subsequently, these values can be used as reference metrics for characterizing the natural history of retinal disease. Furthermore, it will be instrumental in the assessment of functional visual recovery in humans and pre-clinical models of retinal degeneration and optic nerve disease following pharmacological or gene-based therapies. Copyright © 2013 Elsevier Ireland Ltd. All rights reserved.

Risk-rating systems for mature red fir and white fir in northern California

Treesearch

George T. Ferrell

1980-01-01

On the basis of crown and bole characteristics, risk-rating systems to predict the probability that a tree will die within 5 years were developed for mature red fir and white fir in northern California. The systems apply to firs at least 10 inches (25.4 cm) in diameter-at-breast-height (d.b.h.), growing in mature stands, with the original overstory at least partially...

Assessing the susceptibility of white fir to the fir engraver, Scolytus ventralis Lec. (Coleoptera: Scolytidae), using fungal inoculation

Treesearch

G.T. Ferrell; W.J. Otrosina; C.J. DeMars

1993-01-01

A method of assessing susceptibility of white fir, Abies concolor (Gord. and Glend.) Lindl., by fungal inoculation was tested during an outbreak of the fir engraver beetle, Scolytus ventralis LeC., at Lake Tahoe, California, in 1987 through 1989.A total of 592 firs growing in six forest stands containing trees infested by the beetle were inoculated with the mutualistic...

On optimal infinite impulse response edge detection filters

NASA Technical Reports Server (NTRS)

Sarkar, Sudeep; Boyer, Kim L.

1991-01-01

The authors outline the design of an optimal, computationally efficient, infinite impulse response edge detection filter. The optimal filter is computed based on Canny's high signal to noise ratio, good localization criteria, and a criterion on the spurious response of the filter to noise. An expression for the width of the filter, which is appropriate for infinite-length filters, is incorporated directly in the expression for spurious responses. The three criteria are maximized using the variational method and nonlinear constrained optimization. The optimal filter parameters are tabulated for various values of the filter performance criteria. A complete methodology for implementing the optimal filter using approximating recursive digital filtering is presented. The approximating recursive digital filter is separable into two linear filters operating in two orthogonal directions. The implementation is very simple and computationally efficient, has a constant time of execution for different sizes of the operator, and is readily amenable to real-time hardware implementation.

Allelochemicals and activities in a replanted Chinese fir (Cunninghamia lanceolata (Lamb.) Hook) tree ecosystem.

PubMed

Kong, C H; Chen, L C; Xu, X H; Wang, P; Wang, S L

2008-12-24

Autotoxicity is a major reason for replant problems in managed tree ecosystems. Studies have related phenolics-based allelochemicals to autotoxicity. We selected a 20-year-old replanted Chinese fir [Cunninghamia lancealata (Lamb.) Hook] tree ecosystem to isolate, identify, determine the biological activity of, and quantify soil phytotoxins. Eight common phenolics (coumarin, vanillin, isovanillin, and p-hydroxybenzoic, vanillic, benzoic, cinnamic, and ferulic acids), friedelin, and a novel cyclic dipeptide (6-hydroxy-1,3-dimethyl-8-nonadecyl-[1,4]-diazocane-2,5-diketone) were obtained by using the bioassay-guided isolation technique from toxic soil of the replanted Chinese fir tree ecosystem. Chemical structures were determined by spectroscopic means, including 2D-NMR (COSY, HMQC, HMBC, and NOESY) experiments. High concentrations of soil phenolics and friedelin were observed in the natural evergreen broadleaf forest (CK) rather than in the Chinese fir tree ecosystem. The phenolics and friedelin were not phytotoxic to Chinese fir trees. However, the cyclic dipeptide inhibited Chinese fir growth at soil concentrations determined in the replanted Chinese fir tree ecosystem. There was a significantly higher soil concentration of cyclic dipeptide in the replanted Chinese fir tree ecosystem than in a fresh Chinese fir tree ecosystem. The results suggest that phenolics and friedelin are not key allelochemicals since they are weakly phytotoxic and are detected in low concentrations in the replanted Chinese fir tree ecosystem, while cyclic dipeptide is a highly active allelochemical with a phytotoxic effect that limits offspring growth in the replanted Chinese fir tree ecosystem. The discovery of cyclic dipeptide, as well as a further understanding of its potential action mechanism in the replanted Chinese fir tree ecosystem, may contribute to solving the replant problems in managed tree ecosystems.

Precommercial thinning in mixed-species conifer plantations affected by armillaria and heterobasidion root diseases in West-Central Oregon and Washington: 30-year results

Treesearch

Gregory M. Filip; Joshua J. Bronson; Kristen L. Chadwick; Jeremy B. Filip; Susan J. Frankel; Donald J. Goheen; Ellen M. Goheen; Sylvia R. Mori; Angel L. Saavedra

2015-01-01

Four 10- to 20-year-old plantations were precommercially thinned to determine the effects on tree growth and mortality caused by armillaria and heterobasidion root diseases. The plantations represented different species compositions with one each of (1) coastal Douglas-fir and noble fir, (2) Douglas-fir and western hemlock, (3) pure Douglas-fir, and (4) Shasta red fir...

Hybridization of a Rocky Mountain fir (Abies concolor) and a Mexican fir (Abies religiosa).

Treesearch

J.B. St. Clair; W.B. Critchfield

1988-01-01

Interspecific crosses of Abies religiosa (HBK.) Schlecht. & Cham. (oyamel) with Abies concolor (Gord. & Glend.) Lindle. ex Hildebr. var. concolor (white fir) and Abies magnifica A. Murr. (California red fir) were undertaken to explore the relationships between these species. The...

Instrumentation for Kinetic-Inductance-Detector-Based Submillimeter Radio Astronomy

NASA Astrophysics Data System (ADS)

Duan, Ran

A substantial amount of important scientific information is contained within astronomical data at the submillimeter and far-infrared (FIR) wavelengths, including information regarding dusty galaxies, galaxy clusters, and star-forming regions; however, these wavelengths are among the least-explored fields in astronomy because of the technological difficulties involved in such research. Over the past 20 years, considerable efforts have been devoted to developing submillimeter- and millimeter-wavelength astronomical instruments and telescopes. The number of detectors is an important property of such instruments and is the subject of the current study. Future telescopes will require as many as hundreds of thousands of detectors to meet the necessary requirements in terms of the field of view, scan speed, and resolution. A large pixel count is one benefit of the development of multiplexable detectors that use kinetic inductance detector (KID) technology. This dissertation presents the development of a KID-based instrument including a portion of the millimeter-wave bandpass filters and all aspects of the readout electronics, which together enabled one of the largest detector counts achieved to date in submillimeter-/millimeter-wavelength imaging arrays: a total of 2304 detectors. The work presented in this dissertation has been implemented in the MUltiwavelength Submillimeter Inductance Camera (MUSIC), a new instrument for the Caltech Submillimeter Observatory (CSO).

Development of a wireless displacement measurement system using acceleration responses.

PubMed

Park, Jong-Woong; Sim, Sung-Han; Jung, Hyung-Jo; Spencer, Billie F

2013-07-01

Displacement measurements are useful information for various engineering applications such as structural health monitoring (SHM), earthquake engineering and system identification. Most existing displacement measurement methods are costly, labor-intensive, and have difficulties particularly when applying to full-scale civil structures because the methods require stationary reference points. Indirect estimation methods converting acceleration to displacement can be a good alternative as acceleration transducers are generally cost-effective, easy to install, and have low noise. However, the application of acceleration-based methods to full-scale civil structures such as long span bridges is challenging due to the need to install cables to connect the sensors to a base station. This article proposes a low-cost wireless displacement measurement system using acceleration. Developed with smart sensors that are low-cost, wireless, and capable of on-board computation, the wireless displacement measurement system has significant potential to impact many applications that need displacement information at multiple locations of a structure. The system implements an FIR-filter type displacement estimation algorithm that can remove low frequency drifts typically caused by numerical integration of discrete acceleration signals. To verify the accuracy and feasibility of the proposed system, laboratory tests are carried out using a shaking table and on a three storey shear building model, experimentally confirming the effectiveness of the proposed system.

Development of a Wireless Displacement Measurement System Using Acceleration Responses

PubMed Central

Park, Jong-Woong; Sim, Sung-Han; Jung, Hyung-Jo; Spencer, Billie F.

2013-01-01

Displacement measurements are useful information for various engineering applications such as structural health monitoring (SHM), earthquake engineering and system identification. Most existing displacement measurement methods are costly, labor-intensive, and have difficulties particularly when applying to full-scale civil structures because the methods require stationary reference points. Indirect estimation methods converting acceleration to displacement can be a good alternative as acceleration transducers are generally cost-effective, easy to install, and have low noise. However, the application of acceleration-based methods to full-scale civil structures such as long span bridges is challenging due to the need to install cables to connect the sensors to a base station. This article proposes a low-cost wireless displacement measurement system using acceleration. Developed with smart sensors that are low-cost, wireless, and capable of on-board computation, the wireless displacement measurement system has significant potential to impact many applications that need displacement information at multiple locations of a structure. The system implements an FIR-filter type displacement estimation algorithm that can remove low frequency drifts typically caused by numerical integration of discrete acceleration signals. To verify the accuracy and feasibility of the proposed system, laboratory tests are carried out using a shaking table and on a three storey shear building model, experimentally confirming the effectiveness of the proposed system. PMID:23881123

Inhibition of the growth of Alexandrium tamarense by algicidal substances in Chinese fir (Cunninghamia lanceolata).

PubMed

Yang, Wei-Dong; Liu, Jie-Sheng; Li, Hong-Ye; Zhang, Xin-Lian; Qi, Yu-Zao

2009-10-01

The wood sawdust from Chinese fir (Cunninghamia lanceolata) exhibited stronger inhibition on the growth of Alexandrium tamarense than those from alder (Alnus cremastogyne), pine (Pinus massoniana), birch (Betula alnoides) and sapele (Entandrophragma cylindricum). The water extract, acetone-water extract and essential oil from fir sawdust were all shown to inhibit the growth of A. tamarense. The inhibition of fir essential oil was the strongest among all the above wood sources while the half effective concentration was only 0.65 mg/L. These results suggested that the fir essential oil may play an important role in the algicidal effect of Chinese fir.

Hybridization of a Rocky Mountain fir (Abies concolor) and a Mexican fir (Abies religiosa)

Treesearch

J. B. St. Clair; W. B. Critchfield

1988-01-01

Interspecific crosses of Abies religiosa (HBK.) Schlecht. & Cham, (oyamel) with Abies concolor (Gord. & Glend.) Lindl. ex Hildebr. var. concolor (white fir) and Abies magnifica A. Murr. (California red fir) were undertaken to explore the relationships between these species. The cross...

User's guide to the Douglas-fir beetle impact model

Treesearch

Michael A. Marsden; Bov B. Eav; Matthew K. Thompson

1993-01-01

Douglas-fir beetle (Dendroctonus pseudotsugae Hopk.) occurs throughout the range of its principal host, Douglas-fir (Pseudotsuga menziesii (Mirb.) Franco). At epidemic levels, the beetle causes considerable mortality in large-diameter Douglas-fir trees. Wind storms, drought, fire, and other factors have been reported as precedent...

Douglas-Fir Tussock Moth

Treesearch

Boyd E. Wickman; Richard R. Mason; Galen C. Trostle

1981-01-01

The Douglas-fir tussock moth (Orgyia pseudotsugata McDunnough) is an important defoliator of true firs and Douglas-fir in Western North America. Severe tussock moth outbreaks have occurred in British Columbia, Idaho, Washington, Oregon, Nevada, California, Arizona, and New Mexico, but the area subject to attack is more extensive

Effects of far-infrared radiation on heart rate variability and central manifestations in healthy subjects: a resting-fMRI study.

PubMed

Lin, Yii-Jeng; Kung, Yen-Ying; Kuo, Wen-Jui; Niddam, David M; Cheng, Chou-Ming; Chou, Chih-Che; Yeh, Tzu-Chen; Hsieh, Jen-Chuen; Chiu, Jen-Hwey

2015-01-01

The aim of this study was to investigate the autonomic responses and central manifestations by peripheral FIR stimulation. Ten subjects (mean ± SD age 26.2 ± 3.52 years) received FIR stimulation at left median nerve territory for 40 min. Electrocardiograph was continuously recorded and heart rate variability (HRV) were analyzed. By using a 3 T-MRI scanner, three sessions of resting-state functional magnetic resonance images (fMRI) were acquired, namely, before (baseline-FIR), immediately after (IA-FIR) and 15 min after FIR was turned off (Post-FIR). The fractional amplitude of low-frequency (0.01-0.08 Hz) fluctuation (fALFF) of each session to evaluate the intensity of resting-brain activity in each session was analyzed. Our results showed that FIR stimulation induced significant HRV responses such as an increasing trend of nLF and LF/HF ratio, while FIR increased fALFF in right superior front gyrus, middle frontal gyrus and decreased the resting brain activity at fusiform gyrus, extrastriae cortex, inferior temporal gyrus and middle temporal gyrus, especially 15 min after FIR was turned off. We conclude that the central manifestation and the autonomic responses are prominent during and after FIR stimulation, which provide important mechanistic explanation on human disorder treated by such energy medicine.

An Improved Filtering Method for Quantum Color Image in Frequency Domain

NASA Astrophysics Data System (ADS)

Li, Panchi; Xiao, Hong

2018-01-01

In this paper we investigate the use of quantum Fourier transform (QFT) in the field of image processing. We consider QFT-based color image filtering operations and their applications in image smoothing, sharpening, and selective filtering using quantum frequency domain filters. The underlying principle used for constructing the proposed quantum filters is to use the principle of the quantum Oracle to implement the filter function. Compared with the existing methods, our method is not only suitable for color images, but also can flexibly design the notch filters. We provide the quantum circuit that implements the filtering task and present the results of several simulation experiments on color images. The major advantages of the quantum frequency filtering lies in the exploitation of the efficient implementation of the quantum Fourier transform.

Noble fir: a bibliography with abstracts.

Treesearch

Jerry F. Franklin

1962-01-01

This bibliography on noble fir (Abies procera Rehd.) includes both North American and European references. Its purpose is to list articles for those interested in the species; the most important references have been abstracted. An article concerning California red fir and one concerning Shasta red fir are included, as their silvical characteristics...

Economical Implementation of a Filter Engine in an FPGA

NASA Technical Reports Server (NTRS)

Kowalski, James E.

2009-01-01

A logic design has been conceived for a field-programmable gate array (FPGA) that would implement a complex system of multiple digital state-space filters. The main innovative aspect of this design lies in providing for reuse of parts of the FPGA hardware to perform different parts of the filter computations at different times, in such a manner as to enable the timely performance of all required computations in the face of limitations on available FPGA hardware resources. The implementation of the digital state-space filter involves matrix vector multiplications, which, in the absence of the present innovation, would ordinarily necessitate some multiplexing of vector elements and/or routing of data flows along multiple paths. The design concept calls for implementing vector registers as shift registers to simplify operand access to multipliers and accumulators, obviating both multiplexing and routing of data along multiple paths. Each vector register would be reused for different parts of a calculation. Outputs would always be drawn from the same register, and inputs would always be loaded into the same register. A simple state machine would control each filter. The output of a given filter would be passed to the next filter, accompanied by a "valid" signal, which would start the state machine of the next filter. Multiple filter modules would share a multiplication/accumulation arithmetic unit. The filter computations would be timed by use of a clock having a frequency high enough, relative to the input and output data rate, to provide enough cycles for matrix and vector arithmetic operations. This design concept could prove beneficial in numerous applications in which digital filters are used and/or vectors are multiplied by coefficient matrices. Examples of such applications include general signal processing, filtering of signals in control systems, processing of geophysical measurements, and medical imaging. For these and other applications, it could be advantageous to combine compact FPGA digital filter implementations with other application-specific logic implementations on single integrated-circuit chips. An FPGA could readily be tailored to implement a variety of filters because the filter coefficients would be loaded into memory at startup.

User's guide to the douglas-fir beetle impact model. Forest Service general technical report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Marsden, M.A.; Eav, B.B.; Thompson, M.K.

1994-09-01

Douglas-fir beetle occurs throughout the range of its principal host, Douglas-fir. At epidemic levels, the beetle causes considerable mortality in large-diameter Douglas-fir trees. Wind storms, drought, fire, and other factors have been reported as precendent conditions for epidemics of Douglas-fir beetle. An impact model has been developed to simulate tree mortality during such epidemics. The model has been linked to the Stand Prognosis Model (Forest Vegetation Simulator). This is a guide for using the model.

Fuel reduction in residential and scenic forests: A comparison of three treatments in a western Montana ponderosa pine stand

Treesearch

Joe H. Scott

1998-01-01

Three contrasting thinning treatments to reduce fire hazard were implemented in a 100-year-old ponderosa pine/Douglas-fir (Pinus ponderosa/Pseudotsuga menzesii) stand on the Lolo National Forest, MT. All treatments included a commercial thinning designed to reduce crown fuels and provide revenue to offset costs. The treatments are...

Application of analytical redundancy management to Shuttle crafts. [computerized simulation of microelectronic implementation

NASA Technical Reports Server (NTRS)

Montgomery, R. C.; Tabak, D.

1979-01-01

The study involves the bank of filters approach to analytical redundancy management since this is amenable to microelectronic implementation. Attention is given to a study of the UD factorized filter to determine if it gives more accurate estimates than the standard Kalman filter when data processing word size is reduced. It is reported that, as the word size is reduced, the effect of modeling error dominates the filter performance of the two filters. However, the UD filter is shown to maintain a slight advantage in tracking performance. It is concluded that because of the UD filter's stability in the serial processing mode, it remains the leading candidate for microelectronic implementation.

[Community stability for spruce-fir forest at different succession stages in Changbai Mountains, Northeast China].

PubMed

Zhang, Meng-tao; Zhang, Qing; Kang, Xin-gang; Yang, Ying-jun; Xu, Guang; Zhang, Li-xin

2015-06-01

Based on the analysis of three forest communities (polar-birch secondary forest, spruce-fir mixed forest, spruce-fir near pristine forest) in Changbai Mountains, a total of 22 factors of 5 indices, including the population regeneration, soil fertility (soil moisture and soli nutrient), woodland productivity and species diversity that reflected community characteristics were used to evaluate the stability of forest community succession at different stages by calculating subordinate function values of a model based on fuzzy mathematics. The results that the indices of population regeneration, soli nutrient, woodland productivity and species diversity were the highest in the spruce-fir mixed forest, and the indices of soil moisture were the highest in the spruce-fir near-pristine forest. The stability of three forest communities was in order of natural spruce-fir mixed forest > spruce-fir near pristine forest > polar-birch secondary forest.

Predicting postfire Douglas-fir beetle attacks and tree mortality in the northern Rocky Mountains

Treesearch

Sharon Hood; Barbara Bentz

2007-01-01

Douglas-fir (Pseudotsuga menziesii (Mirb.) Franco) were monitored for 4 years following three wildfires. Logistic regression analyses were used to develop models predicting the probability of attack by Douglas-fir beetle (Dendroctonus pseudotsugae Hopkins, 1905) and the probability of Douglas-fir mortality within 4 years following...

Losses associated with Douglas-fir and true fir tops killed by western spruce budworm in eastern Washington.

Treesearch

Paul E. Aho

1984-01-01

A sample of 133 Douglas-firs (Pseudotsuga menziesii var. glauca (Beissn.) Franco) and 69 true firs (Abies spp.) with dead tops caused by defoliation by the western spruce budworm (Choristoneura occidentalis Freeman) were felled, dissected, and examined for height loss and incidence and...

Composition of root pressure exudate from conifers.

Treesearch

D.O. Ketchie; W. Lopushinsky

1981-01-01

Root pressure exudates collected from detopped seedlings of Douglas-fir, grand fir, noble fir, Pacific silver fir, ponderosa pine, lodgepole pine, and Engelmann spruce were analyzed for sugars, amino acids, organic acids, nitrogen, potassium, calcium, and magnesium. Sugar concentrations ranged from 0.10 percent to 5 percent, and included glucose, sucrose, fructose, and...

Effects of fir sawyer beetle on spatial structure of Siberian fir stands

Treesearch

Vladimir L. Gavrikov; Valentina P. Vetrova

1991-01-01

Insects not only use plants for food and habitat; they also change plant populations by influencing their structure and dynamics. This influence is evidenced in the alteration of the spatial structure of a stand. The fir sawyer, Monochamus urussovi Fisch. (Coleoptera: Cerambycidae), is the most abundant xylophagous insect injuring siberian fir,...

Timing of aerial surveys for the balsam woolly aphid

Treesearch

W.J. Buckhorn; Paul G. Lauterbach

1957-01-01

An outbreak of the balsam woolly aphid (Chermes piceae Ratz.) is damaging and killing Pacific silver fir, subalpine fir, and grand fir extensively in western Washington and Oregon. It is most serious in southern Washington where an outbreak on Pacific silver fir was discovered in 1954. Since effective methods for controlling this insect under...

Biological Degradation of Chinese Fir with Trametes Versicolor (L.) Lloyd

PubMed Central

Chen, Meiling; Wang, Chuangui; Fei, Benhua; Ma, Xinxin; Zhang, Bo; Zhang, Shuangyan; Huang, Anmin

2017-01-01

Chinese fir (Cunninghamia lanceolata (Lamb.) Hook.) has been an important afforestation species in northeast China. It has obvious defects of buckling and cracking easily, which are caused by its chemical components. Trametes versicolor (L.) Lloyd, a white-rot fungus, can decompose the cellulose, hemicellulose, and lignin in the wood. White-rot fungus was used to biologically degrade Chinese fir wood. The effects of different degradation time on the Chinese fir wood’s mechanical properties, micromorphology, chemical components, and crystallinity were studied. The results showed that the heartwood of Chinese fir was more durable than the sapwood and the durability class of Chinese fir was III. Trametes versicolor (L.) Lloyd had a greater influence on the mechanical properties (especially with respect to the modulus of elasticity (MOE)) for the sapwood. Trametes versicolor (L.) Lloyd degraded Chinese fir and colonized the lumen of various wood cell types in Chinese fir, penetrated cell walls via pits, caused erosion troughs and bore holes, and removed all cell layers. The ability of white-rot fungus to change the chemical composition mass fraction for Chinese fir was: hemicellulose > lignin > cellulose. The durability of the chemical compositions was: lignin > cellulose > hemicellulose. The crystallinity of the cellulose decreased and the mean size of the ordered (crystalline) domains increased after being treated by white-rot fungus. PMID:28773191

Association of Far-Infrared Radiation Therapy and Ankle-Brachial Index of Patients on Hemodialysis with Peripheral Artery Occlusive Disease

PubMed Central

Chen, Szu-Chia; Lee, Mei-Yueh; Huang, Jiun-Chi; Kuo, I-Ching; Mai, Hsiu-Chin; Kuo, Po-Lin; Chang, Jer-Ming; Hwang, Shang-Jyh; Chen, Hung-Chun

2016-01-01

Background and Aim: The ankle-brachial index (ABI) is recognized to be a good marker for atherosclerosis, and is useful in the diagnosis of peripheral artery occlusive disease (PAOD) which is prevalent among patients on hemodialysis (HD). Methods: This randomized trial aimed to evaluate the effect of far-infrared radiation (FIR) therapy on ABI in HD patients with PAOD. PAOD was defined as patients with ABI < 0.95. One hundred and eight HD patients were enrolled, including 50 in the control group and 58 in the FIR group. A WS TY101 FIR emitter was applied for 40 minutes during each HD session, three times per week for six months. The ABI was measured before and after the FIR therapy. Results: Regardless of FIR therapy, the bilateral ABI decreased (in the FIR group, left: 0.88±0.22 to 0.85±0.24, p = 0.188; right: 0.92±0.20 to 0.90±0.23, p = 0.372; in control group, left: 0.91±0.23 to 0.88±0.21, p = 0144; right: 0.93±0.17 to 0.89±0.21, p = 0.082). Multivariate logistic analysis of the FIR group revealed that high uric acid (odds ratio [OR]: 2.335; 95% confidence interval [CI]: 1.117-4.882; p=0.024) and aspirin use (OR: 16.463; 95% CI: 1.787-151.638; p=0.013) were independently associated with increased bilateral ABI after FIR therapy. Conclusions: This study demonstrates that ABI is not increased after FIR therapy in HD patients with PAOD. However, in the FIR group, patients with higher uric acid level or those who used aspirin have increased bilateral ABI after FIR therapy. PMID:27994503

Silver fir and Douglas fir are more tolerant to extreme droughts than Norway spruce in south-western Germany.

PubMed

Vitali, Valentina; Büntgen, Ulf; Bauhus, Jürgen

2017-12-01

Improving our understanding of the potential of forest adaptation is an urgent task in the light of predicted climate change. Long-term alternatives for susceptible yet economically important tree species such as Norway spruce (Picea abies) are required, if the frequency and intensity of summer droughts will continue to increase. Although Silver fir (Abies alba) and Douglas fir (Pseudotsuga menziesii) have both been described as drought-tolerant species, our understanding of their growth responses to drought extremes is still limited. Here, we use a dendroecological approach to assess the resistance, resilience, and recovery of these important central Europe to conifer species the exceptional droughts in 1976 and 2003. A total of 270 trees per species were sampled in 18 managed mixed-species stands along an altitudinal gradient (400-1200 m a.s.l.) at the western slopes of the southern and central Black Forest in southwest Germany. While radial growth in all species responded similarly to the 1976 drought, Norway spruce was least resistant and resilient to the 2003 summer drought. Silver fir showed the overall highest resistance to drought, similarly to Douglas fir, which exhibited the widest growth rings. Silver fir trees from lower elevations were more drought prone than trees at higher elevations. Douglas fir and Norway spruce, however, revealed lower drought resilience at higher altitudes. Although the 1976 and 2003 drought extremes were quite different, Douglas fir maintained consistently the highest radial growth. Although our study did not examine population-level responses, it clearly indicates that Silver fir and Douglas fir are generally more resistant and resilient to previous drought extremes and are therefore suitable alternatives to Norway spruce; Silver fir more so at higher altitudes. Cultivating these species instead of Norway spruce will contribute to maintaining a high level of productivity across many Central European mountain forests under future climate change. © 2017 John Wiley & Sons Ltd.

MicroRNA-134 Contributes to Glucose-Induced Endothelial Cell Dysfunction and This Effect Can Be Reversed by Far-Infrared Irradiation

PubMed Central

Wang, Yen-Li; Chang, Shih-Ting; Liao, Ko-Hsun; Lo, Hung-Hao; Chiu, Ya-Lin; Hsieh, Tsung-Han; Huang, Tse-Shun; Lin, Chin-Sheng; Cheng, Shu-Meng; Cheng, Cheng-Chung

2016-01-01

Diabetes mellitus (DM) is a metabolic disease that is increasing worldwide. Furthermore, it is associated with the deregulation of vascular-related functions, which can develop into major complications among DM patients. Endothelial colony forming cells (ECFCs) have the potential to bring about medical repairs because of their post-natal angiogenic activities; however, such activities are impaired by high glucose- (HG) and the DM-associated conditions. Far-infrared radiation (FIR) transfers energy as heat that is perceived by the thermoreceptors in human skin. Several studies have revealed that FIR improves vascular endothelial functioning and boost angiogenesis. FIR has been used as anti-inflammatory therapy and as a clinical treatment for peripheral circulation improvement. In addition to vascular repair, there is increasing evidence to show that FIR can be applied to a variety of diseases, including cardiovascular disorders, hypertension and arthritis. Yet mechanism of action of FIR and the biomarkers that indicate FIR effects remain unclear. MicroRNA-134 (miR-134-5p) was identified by small RNA sequencing as being increased in high glucose (HG) treated dfECFCs (HG-dfECFCs). Highly expressed miR-134 was also validated in dmECFCs by RT-qPCR and it is associated with impaired angiogenic activities of ECFCs. The functioning of ECFCs is improved by FIR treatment and this occurs via a reduction in the level of miR-134 and an increase in the NRIP1 transcript, a direct target of miR-134. Using a mouse ischemic hindlimb model, the recovery of impaired blood flow in the presence of HG-dfECFCs was improved by FIR pretreatment and this enhanced functionality was decreased when there was miR-134 overexpression in the FIR pretreated HG-dfECFCs. In conclusion, our results reveal that the deregulation of miR-134 is involved in angiogenic defects found in DM patients. FIR treatment improves the angiogenic activity of HG-dfECFCs and dmECFCs and FIR has potential as a treatment for DM. Detection of miR-134 expression in FIR-treated ECFCs should help us to explore further the effectiveness of FIR therapy. PMID:26799933

MicroRNA-134 Contributes to Glucose-Induced Endothelial Cell Dysfunction and This Effect Can Be Reversed by Far-Infrared Irradiation.

PubMed

Wang, Hsei-Wei; Su, Shu-Han; Wang, Yen-Li; Chang, Shih-Ting; Liao, Ko-Hsun; Lo, Hung-Hao; Chiu, Ya-Lin; Hsieh, Tsung-Han; Huang, Tse-Shun; Lin, Chin-Sheng; Cheng, Shu-Meng; Cheng, Cheng-Chung

2016-01-01

Diabetes mellitus (DM) is a metabolic disease that is increasing worldwide. Furthermore, it is associated with the deregulation of vascular-related functions, which can develop into major complications among DM patients. Endothelial colony forming cells (ECFCs) have the potential to bring about medical repairs because of their post-natal angiogenic activities; however, such activities are impaired by high glucose- (HG) and the DM-associated conditions. Far-infrared radiation (FIR) transfers energy as heat that is perceived by the thermoreceptors in human skin. Several studies have revealed that FIR improves vascular endothelial functioning and boost angiogenesis. FIR has been used as anti-inflammatory therapy and as a clinical treatment for peripheral circulation improvement. In addition to vascular repair, there is increasing evidence to show that FIR can be applied to a variety of diseases, including cardiovascular disorders, hypertension and arthritis. Yet mechanism of action of FIR and the biomarkers that indicate FIR effects remain unclear. MicroRNA-134 (miR-134-5p) was identified by small RNA sequencing as being increased in high glucose (HG) treated dfECFCs (HG-dfECFCs). Highly expressed miR-134 was also validated in dmECFCs by RT-qPCR and it is associated with impaired angiogenic activities of ECFCs. The functioning of ECFCs is improved by FIR treatment and this occurs via a reduction in the level of miR-134 and an increase in the NRIP1 transcript, a direct target of miR-134. Using a mouse ischemic hindlimb model, the recovery of impaired blood flow in the presence of HG-dfECFCs was improved by FIR pretreatment and this enhanced functionality was decreased when there was miR-134 overexpression in the FIR pretreated HG-dfECFCs. In conclusion, our results reveal that the deregulation of miR-134 is involved in angiogenic defects found in DM patients. FIR treatment improves the angiogenic activity of HG-dfECFCs and dmECFCs and FIR has potential as a treatment for DM. Detection of miR-134 expression in FIR-treated ECFCs should help us to explore further the effectiveness of FIR therapy.

Far-infrared radiation acutely increases nitric oxide production by increasing Ca{sup 2+} mobilization and Ca{sup 2+}/calmodulin-dependent protein kinase II-mediated phosphorylation of endothelial nitric oxide synthase at serine 1179

DOE Office of Scientific and Technical Information (OSTI.GOV)

Park, Jung-Hyun; Lee, Sangmi; Cho, Du-Hyong

Highlights: •Far-infrared (FIR) radiation increases eNOS-Ser{sup 1179} phosphorylation and NO production in BAEC. •CaMKII and PKA mediate FIR-stimulated increases in eNOS-Ser{sup 1179} phosphorylation. •FIR increases intracellular Ca{sup 2+} levels. •Thermo-sensitive TRPV Ca{sup 2+} channels are unlikely to be involved in the FIR-mediated eNOS-Ser{sup 1179} phosphorylation pathway. -- Abstract: Repeated thermal therapy manifested by far-infrared (FIR) radiation improves vascular function in both patients and mouse model with coronary heart disease, but its underlying mechanism is not fully understood. Using FIR as a thermal therapy agent, we investigate the molecular mechanism of its effect on endothelial nitric oxide synthase (eNOS) activity andmore » NO production. FIR increased the phosphorylation of eNOS at serine 1179 (eNOS-Ser{sup 1179}) in a time-dependent manner (up to 40 min of FIR radiation) in bovine aortic endothelial cells (BAEC) without alterations in eNOS expression. This increase was accompanied by increases in NO production and intracellular Ca{sup 2+} levels. Treatment with KN-93, a selective inhibitor of Ca{sup 2+}/calmodulin-dependent protein kinase II (CaMKII) and H-89, a protein kinase A inhibitor, inhibited FIR radiation-stimulated eNOS-Ser{sup 1179} phosphorylation. FIR radiation itself also increased the temperature of culture medium. As transient receptors potential vanilloid (TRPV) ion channels are known to be temperature-sensitive calcium channels, we explore whether TRPV channels mediate these observed effects. Reverse transcription-PCR assay revealed two TRPV isoforms in BAEC, TRPV2 and TRPV4. Although ruthenium red, a pan-TRPV inhibitor, completely reversed the observed effect of FIR radiation, a partial attenuation (∼20%) was found in cells treated with Tranilast, TRPV2 inhibitor. However, ectopic expression of siRNA of TRPV2 showed no significant alteration in FIR radiation-stimulated eNOS-Ser{sup 1179} phosphorylation. This study suggests that FIR radiation increases NO production via increasing CaMKII-mediated eNOS-Ser{sup 1179} phosphorylation but TRPV channels may not be involved in this pathway. Our results may provide the molecular mechanism by which FIR radiation improves endothelial function.« less

Improved understanding of the loss-of-symmetry phenomenon in the conventional Kalman filter

NASA Technical Reports Server (NTRS)

Verhaegen, M. H.

1987-01-01

This paper corrects an unclear treatment of the conventional Kalman filter implementation as presented by M. H. Verhaegen and P. van Dooren in Numerical aspects of different Kalman filter implementations, IEEE Trans. Automat. Contr., v. AC-31, no. 10, pp. 907-917, 1986. It is shown that habitual, incorrect implementation of the Kalman filter has been the major cause of its sensitivity to the so-called loss-of-symmetry phenomenon.

Design and Implementation of Embedded Computer Vision Systems Based on Particle Filters

DTIC Science & Technology

2010-01-01

for hardware/software implementa- tion of multi-dimensional particle filter application and we explore this in the third application which is a 3D...methodology for hardware/software implementation of multi-dimensional particle filter application and we explore this in the third application which is a...and hence multiprocessor implementation of parti- cle filters is an important option to examine. A significant body of work exists on optimizing generic

Trapping Douglas-fir beetle (Dendroctonus pseudotsugae) with pheromone baited multiple-funnel traps does not reduce Douglas-fir (Pseudotsuga menziesii) mortality

Treesearch

R.A. Progar; N. Sturdevant; M.J. Rinella

2010-01-01

Douglas-fir beetle (Dendroctonus pseudotsugae Hopkins) (DFB) causes considerable mortality to Douglas-fir (Pseudotsuga menziesii (Mirb.) Franco) in western North American forests. We evaluated the use of semiochemical-baited multiple-funnel traps for the protection of small, high-value stands of trees, such as those occurring...

Size of Douglas-fir trees in relation to distance from a mixed red alder - Douglas-fir stand

Treesearch

R.E. Miller; D.L. Reukema; T.A. Max

1993-01-01

Variation in diameter, height, and stem volume of 57-year-old Douglas-fir(Pseudotsuga menziesii var. menziesii (Mirb.) Franco) was related to distance of these trees from a 27 m wide strip in the same Douglas-fir plantation that had been interplanted with red alder (Alnus rubra Bong.). Within the...

HOW to Identify and Manage Needlecast Diseases on Balsam Fir

Treesearch

Mike Albers; Jana Albers; Jane Cummings Carlson; Linda Haugen; Nancy Wenner

1996-01-01

Needlecast diseases are common in balsam fir stands and Christmas tree plantations in the northeastern and north central United States and in southern Ontario, Quebec, and New Brunswick. Three different needlecast fungi, Lirula nervata, Lirula mirabilis and Isthmiella faullii, cause similar disease symptoms on balsam fir. These diseases may affect other firs planted in...

Ten-year risk-rating systems for California red fir and white fir: development and use

Treesearch

George T. Ferrell

1989-01-01

Logistic regression equations predicting the probability that a tree will die from natural causes--insects, diseases, intertree competition--within 10 years have been developed for California red fir (Abies magnifica) and white fir (A. concolor). The equations, like those with a 5-year prediction period already developed for these...

Diagnosis of Annosus Root Disease in Mixed Conifer Forests in the Northwestern United States

Treesearch

Craig L. Schmitt

1989-01-01

Recognizing annosus root disease affecting conifers in northwestern United States forests is discussed. Field diagnosis can bemade by observing characteristic stand patterns, wood stain and decay, ectotrophic mycelium, and sporophores. Most seriously affected trees include hemlocks, grand fir, white fir and Pacific silver fir. Ponderosa pine and other true firs may...

Decay of subalpine fir in Colorado

Treesearch

Thomas E. Hinds; Frank G. Hawksworth; Ross W. Davidson

1960-01-01

Spruce-fir is one of the major forest types in the central Rocky Mountains. Engelmann spruce, Picea engelmanni Parry, is usually the predominant species with subalpine fir, Abies lasiocarpa (Hook. ) Nutt., making up one-fourth or less of the total volume. Lodgepole pine, Pinus contorta Dougl. ex Loud., is frequently present at the lower elevations of the spruce-fir...

Stability of nuclear DNA content among divergent and isolated populations of Fraser fir

Treesearch

L.D. Auckland; J.S. Johnston; H.J. Price; F.E. Bridgwater

2001-01-01

Fraser fir (Abies fraseri (Pursh) Poir.) is an endemic species consisting of six major disjunct populations in the Appalachian Mountains, U.S.A. Nuclear DNA content was measured with laser flow cytometry to determine if genome size differences could be detected among the disjunct populations of Fraser fir and its close relatives, balsam fir

Altitudinal gradients of bryophyte diversity and community assemblage in southern Appalachian spruce-fir forests

Treesearch

Sarah E. Stehn; Christopher R. Webster; Janice M. Glime; Michael A. Jenkins

2010-01-01

Ground-layer plant communities in spruce-fir forests of the southern Appalachians have likely undergone significant change since the widespread death of canopy Fraser fir (Abies fraseri) caused by the exotic balsam woolly adelgid (Adelges piceae). Bryophytes comprise an important part of the ground-layer flora in the spruce-fir...

A SYNCHRONIZED FIR/VUV LIGHT SOURCE AT JEFFERSON LAB

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stephen Benson, David Douglas, George Neil, Michelle D. Shinn, Gwyn Williams

We describe a dual free-electron laser (FEL) configuration on the UV Demo FEL at Jefferson Lab that allows simultaneous lasing at FIR/THz and UV wavelengths. The FIR/THz source would be an FEL oscillator with a short wiggler providing nearly diffraction-limited pulses with pulse energy exceeding 50 microJoules. The FIR source would use the exhaust beam from a UVFEL. The coherent harmonics in the VUV from the UVFEL are out-coupled through a hole. The FIR source uses a shorter resonator with either hole or edge coupling to provide very high power FIR pulses. Simulations indicate excel-lent spectral brightness in the FIRmore » region with over 100 W/cm-1 output.« less

A fast ellipse extended target PHD filter using box-particle implementation

NASA Astrophysics Data System (ADS)

Zhang, Yongquan; Ji, Hongbing; Hu, Qi

2018-01-01

This paper presents a box-particle implementation of the ellipse extended target probability hypothesis density (ET-PHD) filter, called the ellipse extended target box particle PHD (EET-BP-PHD) filter, where the extended targets are described as a Poisson model developed by Gilholm et al. and the term "box" is here equivalent to the term "interval" used in interval analysis. The proposed EET-BP-PHD filter is capable of dynamically tracking multiple ellipse extended targets and estimating the target states and the number of targets, in the presence of clutter measurements, false alarms and missed detections. To derive the PHD recursion of the EET-BP-PHD filter, a suitable measurement likelihood is defined for a given partitioning cell, and the main implementation steps are presented along with the necessary box approximations and manipulations. The limitations and capabilities of the proposed EET-BP-PHD filter are illustrated by simulation examples. The simulation results show that a box-particle implementation of the ET-PHD filter can avoid the high number of particles and reduce computational burden, compared to a particle implementation of that for extended target tracking.

Discrete wavelet transform: a tool in smoothing kinematic data.

PubMed

Ismail, A R; Asfour, S S

1999-03-01

Motion analysis systems typically introduce noise to the displacement data recorded. Butterworth digital filters have been used to smooth the displacement data in order to obtain smoothed velocities and accelerations. However, this technique does not yield satisfactory results, especially when dealing with complex kinematic motions that occupy the low- and high-frequency bands. The use of the discrete wavelet transform, as an alternative to digital filters, is presented in this paper. The transform passes the original signal through two complementary low- and high-pass FIR filters and decomposes the signal into an approximation function and a detail function. Further decomposition of the signal results in transforming the signal into a hierarchy set of orthogonal approximation and detail functions. A reverse process is employed to perfectly reconstruct the signal (inverse transform) back from its approximation and detail functions. The discrete wavelet transform was applied to the displacement data recorded by Pezzack et al., 1977. The smoothed displacement data were twice differentiated and compared to Pezzack et al.'s acceleration data in order to choose the most appropriate filter coefficients and decomposition level on the basis of maximizing the percentage of retained energy (PRE) and minimizing the root mean square error (RMSE). Daubechies wavelet of the fourth order (Db4) at the second decomposition level showed better results than both the biorthogonal and Coiflet wavelets (PRE = 97.5%, RMSE = 4.7 rad s-2). The Db4 wavelet was then used to compress complex displacement data obtained from a noisy mathematically generated function. Results clearly indicate superiority of this new smoothing approach over traditional filters.

Far-infrared protects vascular endothelial cells from advanced glycation end products-induced injury via PLZF-mediated autophagy in diabetic mice

PubMed Central

Chen, Cheng-Hsien; Chen, Tso-Hsiao; Wu, Mei-Yi; Chou, Tz-Chong; Chen, Jia-Rung; Wei, Meng-Jun; Lee, San-Liang; Hong, Li-Yu; Zheng, Cai-Mei; Chiu, I-Jen; Lin, Yuh-Feng; Hsu, Ching-Min; Hsu, Yung-Ho

2017-01-01

The accumulation of advanced glycation end products (AGEs) in diabetic patients induces vascular endothelial injury. Promyelocytic leukemia zinc finger protein (PLZF) is a transcription factor that can be activated by low-temperature far-infrared (FIR) irradiation to exert beneficial effects on the vascular endothelium. In the present study, we investigated the influence of FIR-induced PLZF activation on AGE-induced endothelial injury both in vitro and in vivo. FIR irradiation inhibited AGE-induced apoptosis in human umbilical vein endothelial cells (HUVECs). PLZF activation increased the expression of phosphatidylinositol-3 kinases (PI3K), which are important kinases in the autophagic signaling pathway. FIR-induced PLZF activation led to autophagy in HUVEC, which was mediated through the upregulation of PI3K. Immunofluorescence staining showed that AGEs were engulfed by HUVECs and localized to lysosomes. FIR-induced autophagy promoted AGEs degradation in HUVECs. In nicotinamide/streptozotocin-induced diabetic mice, FIR therapy reduced serum AGEs and AGEs deposition at the vascular endothelium. FIR therapy also reduced diabetes-induced inflammatory markers in the vascular endothelium and improved vascular endothelial function. These protective effects of FIR therapy were not found in PLZF-knockout mice. Our data suggest that FIR-induced PLZF activation in vascular endothelial cells protects the vascular endothelium in diabetic mice from AGE-induced injury. PMID:28071754

Natural regeneration 10 years after a Douglas-fir tussock moth outbreak in northeastern Oregon.

Treesearch

B.E. Wickman; K.W. Seidel; G. Lynn Star

1986-01-01

A survey of natural regeneration 10 years after severe grand fir mortality caused by an outbreak of Douglas-fir tussock moth was conducted in the Wenaha-Tucannon Wilderness in the Blue Mountains of northeastern Oregon. Seedling stocking was only moderate, but seedling density was adequate where present. Grand fir is dominating both preoutbreak and postoutbreak...

Douglas-fir growth and yield: research 1909-1960.

Treesearch

R.O. Curtis; D.D. Marshall

2004-01-01

Systematic research on growth and yield of Douglas-fir began in 1909. This line of early research evolved over time and culminated in publication of USDA Bulletin 201, The Yield of Douglas-fir in the Pacific Northwest. B201 had an enormous influence on development of Douglas-fir forestry and was arguably the most influential single research publication ever produced in...

Symptoms associated with inoculation of stems on living Douglas-fir and Grand Fir Trees with Phytophthora ramorum

Treesearch

Gary Chastagner; Kathy Riley; Katie Coats; Marianne Elliott; Annie DeBauw; Norm Dart

2010-01-01

To obtain a better understanding of the potential risk of infection and colonization of living Douglas-fir (Pseudotsuga menziesii) and grand fir (Abies grandis) stems, the stems on over 150 trees of each species were inoculated at a Christmas tree farm near Los Gatos, California. This study had the following objectives: 1)...

Decay in white fir top-killed by Douglas-fir tussock moth.

Treesearch

Boyd E. Wickman; Robert F. Scharpf

1972-01-01

Stands heavily defoliated in 1936-37 by the Douglas-fir tussock moth, Hemerocampa pseudotsugata McD., at Mammoth Lakes, California, were studied to determine the incidence and extent of decay in top-damaged trees. This was done by dissecting the tops of trees felled during logging. Comparisons were made with white fir in a nearby logged area that was...

Growth of White fir after Douglas-fir tussock moth outbreaks: long-term records in the Sierra Nevada.

Treesearch

Boyd E. Wickman

1986-01-01

Radial growth of white fir trees, Abies concolor (Gord. and Glend.) Lindl. ex Hildebr., defoliated almost 30 years ago by Douglas-fir tussock moth, Orgyia pseudotsugata (McDunnough), in the central Sierra Nevada was compared with 22 years of growth prior to the outbreak. There was little difference in growth between the two...

Little response of true fir saplings to understory shrub removal

Treesearch

William W. Oliver; Fabian C.C. Uzoh

2002-01-01

The ability of white fir and California red fir to become established, persist, and eventually dominate montane shrub fields is well known. When the firs have eventually dominated do the understory shrubs continue to inhibit growth? In a small study in the southern Cascade Range of northeastern California, we tested the growth response of a thinned stand of saplings to...

Environmental characteristics of the Grand Fir Mosaic and adjacent habitat types

Treesearch

Dennis E. Ferguson; John C. Byrne

2000-01-01

Grand Fir Mosaic habitats differ from adjacent forest habitats in their slow rate of secondary succession to woody vegetation. Remote monitoring stations were used to sample the environment at a Grand Fir Mosaic site and three adjacent habitat types. The Grand Fir Mosaic site has shorter growing seasons, cooler temperatures, and more soil moisture than the other sites...

Mortality patterns following spruce budworm infestation in unprotected spruce-fir forests in Maine

Treesearch

Dale S. Solomon; Lianjun Zhang; Thomas B. Brann; David S. Larrick

2003-01-01

Cumulative and annual mortality of red spruce (Picea rubens Sarg.) and balsam fir [Abies balsamea (L) Mill.] were examined over a 10 yr period to follow the mortality patterns in unprotected spruce-fir forests in northern Maine. Different mortality patterns were determined based on stand composition classes and merchantability classes. In general, balsam fir was more...

Early development of matched planted and naturally regenerated Douglas-fir stands after slash burning in the Cascade Range.

Treesearch

R.E. Miller; R.E. Bigley; S. Webster

1993-01-01

We compared matched planted and naturally regenerated plots in 35- to 38- year-old Douglas-fir (Pseudotsuga menziesii var. menziesii) stands at seven locations in western Washington and Oregon. Total number of live stems is similar, but stands planted to Douglas fir average 26 more live stemslac of Douglas-fir and 39 fewer...

Tree Biomass Estimation of Chinese fir (Cunninghamia lanceolata) Based on Bayesian Method

PubMed Central

Zhang, Jianguo

2013-01-01

Chinese fir (Cunninghamia lanceolata (Lamb.) Hook.) is the most important conifer species for timber production with huge distribution area in southern China. Accurate estimation of biomass is required for accounting and monitoring Chinese forest carbon stocking. In the study, allometric equation was used to analyze tree biomass of Chinese fir. The common methods for estimating allometric model have taken the classical approach based on the frequency interpretation of probability. However, many different biotic and abiotic factors introduce variability in Chinese fir biomass model, suggesting that parameters of biomass model are better represented by probability distributions rather than fixed values as classical method. To deal with the problem, Bayesian method was used for estimating Chinese fir biomass model. In the Bayesian framework, two priors were introduced: non-informative priors and informative priors. For informative priors, 32 biomass equations of Chinese fir were collected from published literature in the paper. The parameter distributions from published literature were regarded as prior distributions in Bayesian model for estimating Chinese fir biomass. Therefore, the Bayesian method with informative priors was better than non-informative priors and classical method, which provides a reasonable method for estimating Chinese fir biomass. PMID:24278198

Tree biomass estimation of Chinese fir (Cunninghamia lanceolata) based on Bayesian method.

PubMed

Zhang, Xiongqing; Duan, Aiguo; Zhang, Jianguo

2013-01-01

Chinese fir (Cunninghamia lanceolata (Lamb.) Hook.) is the most important conifer species for timber production with huge distribution area in southern China. Accurate estimation of biomass is required for accounting and monitoring Chinese forest carbon stocking. In the study, allometric equation W = a(D2H)b was used to analyze tree biomass of Chinese fir. The common methods for estimating allometric model have taken the classical approach based on the frequency interpretation of probability. However, many different biotic and abiotic factors introduce variability in Chinese fir biomass model, suggesting that parameters of biomass model are better represented by probability distributions rather than fixed values as classical method. To deal with the problem, Bayesian method was used for estimating Chinese fir biomass model. In the Bayesian framework, two priors were introduced: non-informative priors and informative priors. For informative priors, 32 biomass equations of Chinese fir were collected from published literature in the paper. The parameter distributions from published literature were regarded as prior distributions in Bayesian model for estimating Chinese fir biomass. Therefore, the Bayesian method with informative priors was better than non-informative priors and classical method, which provides a reasonable method for estimating Chinese fir biomass.

Ecophysiology and growth of advance red spruce and balsam fir regeneration after partial cutting in yellow birch-conifer stands.

PubMed

Dumais, Daniel; Prévost, Marcel

2008-08-01

We investigated ecophysiological and growth responses of short (0.4 to 1.3 m in height) advance regeneration of red spruce (Picea rubens Sarg.) and balsam fir (Abies balsamea L.) six years after removal of 0, 40, 50, 60 and 100% of the overstory basal area (BA) in two yellow birch-conifer stands. Partial cuts significantly increased stomatal conductance of red spruce only. Light-saturated photosynthesis (leaf-area basis) of both species increased with BA removal, but unlike red spruce, specific leaf area (SLA) of balsam fir decreased with increased cutting intensity. Partial cuts appreciably increased the concentration of N and Ca in red spruce and balsam fir foliage, respectively, and resulted in decreased foliar concentrations of K in red spruce and Mg in balsam fir. The height and lateral growth of both species increased with BA removal, although partial cuts were more beneficial to balsam fir. The data suggest that short advance regeneration of red spruce and balsam fir can coexist under partial overstory conditions, but balsam fir has physiological characteristics and a capacity for morphological adjustment (SLA) that places it at an advantage when in competition with red spruce.

Dual-Emission SG7@MOF Sensor via SC-SC Transformation: Enhancing the Formation of Excimer Emission and the Range and Sensitivity of Detection.

PubMed

Fu, Hong-Ru; Wu, Xiao-Xia; Ma, Lu-Fang; Wang, Fei; Zhang, Jian

2018-05-30

In this study, a water stable metal-organic framework FIR-53 is applied as a single-crystal container for anion exchange. The exceptional chemical stability and low crystallographic symmetry of FIR-53 makes it possible to determine anionic guests. Through ion exchange and single-crystal to single-crystal (SC-SC) transformation, 8-hydroxypyrene-1,3,6-trisulfonate (SG7, solvent green 7, ion form as SG7 3- ) is introduced into the pores of FIR-53 to obtain SG7@FIR-53. Because of the spatial confinement and partition effect, SG7@FIR-53 shows the bright exciter emission of SG7 ions. Interestingly, the composite SG7@FIR-53 exhibits a sensitive fluorescence quenching response against Cr 2 O 7 2- and MnO 4 - in aqueous solution. Especially, the detection limit toward MnO 4 - is as low as 0.12 ppb, which is the smallest value to date. Moreover, the prepared SG7@FIR-53 film also displays a broad response to nitro explosives in vapor/aqueous phase. Compared with the results of FIR-53, the range and sensitivity were greatly improved.

WATER AND METHANOL MASER ACTIVITIES IN THE NGC 2024 FIR 6 REGION

DOE Office of Scientific and Technical Information (OSTI.GOV)

Choi, Minho; Kang, Miju; Byun, Do-Young

The NGC 2024 FIR 6 region was observed in the water maser line at 22 GHz and the methanol class I maser lines at 44, 95, and 133 GHz. The water maser spectra displayed several velocity components and month-scale time variabilities. Most of the velocity components may be associated with FIR 6n, while one component was associated with FIR 4. A typical lifetime of the water maser velocity components is about eight months. The components showed velocity fluctuations with a typical drift rate of about 0.01 km s{sup -1} day{sup -1}. The methanol class I masers were detected toward FIRmore » 6. The methanol emission is confined within a narrow range around the systemic velocity of the FIR 6 cloud core. The methanol masers suggest the existence of shocks driven by either the expanding H II region of FIR 6c or the outflow of FIR 6n.« less

Cooperative advanced-generation breeding and testing of coastal Douglas-fir and western hemlock—strategy and implementation.

Treesearch

K. J.S. Jayawickrama; G.R. Johnson; T. Ye

2005-01-01

As in many temperate regions of the world, forest tree improvement got underway in the Pacific Northwest of the USA in the 1950s, with a number of companies and agencies starting independent tree improvement programs. Booth-Kelly Lumber Co., Crown Zellerbach Corp., the Industrial Forestry Association, Port Blakely Mill Co., Simpson Timber Co., Timber Service Co., the...

Adenovirus-mediated FIR demonstrated TP53-independent cell-killing effect and enhanced antitumor activity of carbon-ion beams.

PubMed

Kano, M; Matsushita, K; Rahmutulla, B; Yamada, S; Shimada, H; Kubo, S; Hiwasa, T; Matsubara, H; Nomura, F

2016-01-01

Combination therapy of carbon-ion beam with the far upstream element-binding protein (FBP)-interacting repressor, FIR, which interferes with DNA damage repair proteins, was proposed as an approach for esophageal cancer treatment with low side effects regardless of TP53 status. In vivo therapeutic antitumor efficacy of replication-defective adenovirus (E1 and E3 deleted adenovirus serotype 5) encoding human FIR cDNA (Ad-FIR) was demonstrated in the tumor xenograft model of human esophageal squamous cancer cells, TE-2. Bleomycin (BLM) is an anticancer agent that introduces DNA breaks. The authors reported that Ad-FIR involved in the BLM-induced DNA damage repair response and thus applicable for other DNA damaging agents. To examine the effect of Ad-FIR on DNA damage repair, BLM, X-ray and carbon-ion irradiation were used as DNA damaging agents. The biological effects of high linear energy transfer (LET) radiotherapy used with carbon-ion irradiation are more expansive than low-LET conventional radiotherapy, such as X-rays or γ rays. High LET radiotherapy is suitable for the local control of tumors because of its high relative biological effectiveness. Ad-FIR enhanced BLM-induced DNA damage indicated by γH2AX in vitro. BLM treatment increased endogenous nuclear FIR expression in TE-2 cells, and P27Kip1 expression was suppressed by TP53 siRNA and BLM treatment. Further, Ad-FIRΔexon2, a dominant-negative form of FIR that lacks exon2 transcriptional repression domain, decreased Ku86 expression. The combination of Ad-FIR and BLM in TP53 siRNA increased DNA damage. Additionally, Ad-FIR showed synergistic cell toxicity with X-ray in vitro and significantly increased the antitumor efficacy of carbon-ion irradiation in the xenograft mouse model of TE-2 cells (P=0.03, Mann-Whitney's U-test) and was synergistic with the sensitization enhancement ratio (SER) value of 1.15. Therefore, Ad-FIR increased the cell-killing activity of the carbon-ion beam that avoids late-phase severe adverse effects independently of the TP53 status in vitro. Our findings indicated the feasibility of the combination of Ad-FIR with DNA damaging agents for future esophageal cancer treatment.

A key to arboreal spiders of Douglas-fir and true fir forests of the Pacific Northwest.

Treesearch

A.R. Moldenke; B.L. Fichter; W.P. Stephen; C.E. Griswold

1987-01-01

This illustrated key for identifying spiders inhabiting true fir and Douglas-fir is based on extensive collections from throughout the three North American Pacific Coast States. Details of the age classes present at budburst and the season in which to expect adults are presented for all species. This paper is written for people unfamiliar as well as familiar with...

Stand and tree characteristics influencing density of fir engraver beetle attack scars in white fir

Treesearch

George T. Ferrell

1973-01-01

Density of embedded scars resulting from old fir engraver (Scolytus ventralis Lec.) attacks was assessed in 3,430 bole cross sections cut from 603 white firs growing in both cutover and in virgin old-growth stands in northern California. Mean scar density was directly related to percentage of mature stand removed by logging and was higher in...

Mortality of spruce and fir in Maine in 1976-78 due to the spruce budworm outbreak

Treesearch

Donald W. Seegrist; Stanford L. Arner

1982-01-01

The spruce budworm population in Maine's spruce-fir forests has been at epidemic levels since the early 1970's. Spruce-fir mortality in 1976-78 is compared with predictions of what mortality would have been had the natural mortality rates remained at the levels experienced before the budworm outbreak. It appears that mortality of spruce and fir has increased...

Impact of the first recorded outbreak of the Douglas-fir tussock moth, Orgyia pseudotsugata, in southern California and the extent of its distribution in the Pacific Southwest region

Treesearch

Tom W. Coleman; Michael I. Jones; Beatrice Courtial; Andrew D. Graves; Meghan Woods; Alain Roques; Steven J. Seybold

2014-01-01

The Douglas-fir tussock moth (DFTM), Orgyia pseudotsugata McDunnough (Lepidoptera:Erebidae: Lymantriinae), is a native western North American defoliator of true fir, Abies spp. Mill., and Douglas-fir, Pseudotsuga menziesii (Mirb.) Franco. We investigated the population genetics and impact associated with the first recorded...

Estimating extent of mortality associated with the Douglas-fir beetle in the Central and Northern Rockies

Treesearch

Jose F. Negron; Willis C. Schaupp; Kenneth E. Gibson; John Anhold; Dawn Hansen; Ralph Thier; Phil Mocettini

1999-01-01

Data collected from Douglas-fir stands infected by the Douglas-fir beetle in Wyoming, Montana, Idaho, and Utah, were used to develop models to estimate amount of mortality in terms of basal area killed. Models were built using stepwise linear regression and regression tree approaches. Linear regression models using initial Douglas-fir basal area were built for all...

Recent Advances in Laboratory Infrared Spectroscopy of Polycyclic Aromatic Hydrocarbons: PAHs in the Far Infrared

NASA Technical Reports Server (NTRS)

Mattioda, Andrew L.; Ricca, Alessandra; Tucker, Jonathan; Boersma, Christiaan; Bauschlicher, Charles, Jr.; Allamandola, Louis J.

2010-01-01

Over 25 years of observations and laboratory work have shown that the mid-IR spectra of a majority of astronomical sources are dominated by emission features near 3.3, 6.2, 7.7, and 11.2 microns, which originate in free polycyclic aromatic hydrocarbon (PAH) molecules. PAHs dominate the mid-IR emission from many galactic and extragalactic objects. As such, this material tracks a wide variety of astronomical processes, making this spectrum a powerful probe of the cosmos Apart from bands in the mid-IR, PAHs have bands spanning the Far-IR (FIR) and emission from these FIR features should be present in astronomical sources showing the Mid-IR PAH bands. However, with one exception, the FIR spectral characteristics are known only for a few neutral small PAHs trapped in salt pellets or oils at room temperature, data which is not relevant to astrophysics. Furthermore, since most emitting PAHs responsible for the mid-IR astronomical features are ionized, the absence of any experimental or theoretical PAH ion FIR spectra will make it impossible to correctly interpret the FIR data from these objects. In view of the upcoming Herschel space telescope mission and SOFIA's FIR airborne instrumentation, which will pioneer the FIR region, it is now urgent to obtain PAH FIR spectra. This talk will present an overview recent advances in the laboratory spectroscopy of PAHs, Highlighting the FIR spectroscopy along with some quantum calculations.

Fifteen-year results from a Grand fir-Shasta red fir spacing study.

Treesearch

K.W. Seidel

1987-01-01

A 43-year-old, even-aged stand of advance reproduction of grand fir and Shasta red fir in central Oregon responded to release and thinning with diameter and height growth two to three times the prerelease rate. The response began the first growing season after the overstory was killed with 2,4-D. Diameter growth during the second and third 5-year periods after release...

Tree growth in thinned and unthinned White fir stands 20 years after a Douglas-fir tussock moth outbreak.

Treesearch

Boyd E. Wickman

1988-01-01

Twenty-year postoutbreak growth was compared in thinned and unthinned, severely defoliated stands. Basal area of unthinned white fir has declined 37 percent and pine basal area has increased 32 percent since 1964. The stand thinned in 1960 has the lowest basal area in the study area, but the greatest tree growth before and after the outbreak. All defoliated fir are...

Evolutionary history and population genetics of fraser fir and intermediate fir, southern Appalachian endemic conifers imperiled by an exotic pest and climate change

Treesearch

Kevin M. Potter; John Frampton; Sedley Josserand; C. Dana. Nelson

2010-01-01

Two Abies (true fir) taxa are endemic to high elevations of the Appalachian Mountains, where both are restricted to small populations and are imperiled by the same exotic insect. Fraser fir (Abies fraseri) exists in a handful of island-like populations on mountain ridges in the southern Appalachians of North Carolina, Tennessee and...

A preliminary study of the deterioration of alder and Douglas-fir chips in outdoor piles.

Treesearch

Ernest. Wright

1954-01-01

In the fall of 1952, E. E. Matson of the Pacific Northwest Forest and Range Experiment Station learned that the Fir-Tex Insulating Board Company bf St. Helens, Oregon was considering mixing alder with Douglas-fir chips for outside storage. Since alder heartwood i s more susceptible to decay than that of Douglas-fir, the question arose whether mixing the two might...

The Far Infrared Earth

NASA Technical Reports Server (NTRS)

Harries, John; Carli, Bruno; Rizzi, Rolando; Serio, Carmine; Mlynczak, Martin G.; Palchetti, Luca; Maestri, T.; Brindley, H.; Masiello, Guido

2007-01-01

The paper presents a review of the far infrared (FIR) properties of the Earth's atmosphere, and the role of these properties in climate. These properties have been relatively poorly understood, and it is one of the purposes of this review to demonstrate that, in recent years, we have made great strides in improving this understanding. Seen from space, the Earth is a cool object, with an effective emitting temperature of about 255 K. This contrasts with a global mean surface temperature of 288 K, and is due primarily to strong absorption of outgoing longwave energy by water vapour, carbon dioxide and clouds (especially ice). A large fraction of this absorption occurs in the FIR, and so the Earth is effectively a FIR planet. The FIR is important in a number of key climate processes, for example the water vapour and cloud feedbacks (especially ice clouds). The FIR is also a spectral region which can be used to remotely sense and retrieve atmospheric composition in the presence of ice clouds. Recent developments in instrumentation have allowed progress in each of these areas, which are described, and proposals for a spaceborne FIR instrument are being formulated. It is timely to review the FIR properties of the clear and cloudy atmosphere, the role of FIR processes in climate, and its use in observing our planet from space.

Far-infrared suppresses skin photoaging in ultraviolet B-exposed fibroblasts and hairless mice.

PubMed

Chiu, Hui-Wen; Chen, Cheng-Hsien; Chen, Yi-Jie; Hsu, Yung-Ho

2017-01-01

Ultraviolet (UV) induces skin photoaging, which is characterized by thickening, wrinkling, pigmentation, and dryness. Collagen, which is one of the main building blocks of human skin, is regulated by collagen synthesis and collagen breakdown. Autophagy was found to block the epidermal hyperproliferative response to UVB and may play a crucial role in preventing skin photoaging. In the present study, we investigated whether far-infrared (FIR) therapy can inhibit skin photoaging via UVB irradiation in NIH 3T3 mouse embryonic fibroblasts and SKH-1 hairless mice. We found that FIR treatment significantly increased procollagen type I through the induction of the TGF-β/Smad axis. Furthermore, UVB significantly enhanced the expression of matrix metalloproteinase-1 (MMP-1) and MMP-9. FIR inhibited UVB-induced MMP-1 and MMP-9. Treatment with FIR reversed UVB-decreased type I collagen. In addition, FIR induced autophagy by inhibiting the Akt/mTOR signaling pathway. In UVB-induced skin photoaging in a hairless mouse model, FIR treatment resulted in decreased skin thickness in UVB irradiated mice and inhibited the degradation of collagen fibers. Moreover, FIR can increase procollagen type I via the inhibition of MMP-9 and induction of TGF-β in skin tissues. Therefore, our study provides evidence for the beneficial effects of FIR exposure in a model of skin photoaging.

Implicit Kalman filtering

NASA Technical Reports Server (NTRS)

Skliar, M.; Ramirez, W. F.

1997-01-01

For an implicitly defined discrete system, a new algorithm for Kalman filtering is developed and an efficient numerical implementation scheme is proposed. Unlike the traditional explicit approach, the implicit filter can be readily applied to ill-conditioned systems and allows for generalization to descriptor systems. The implementation of the implicit filter depends on the solution of the congruence matrix equation (A1)(Px)(AT1) = Py. We develop a general iterative method for the solution of this equation, and prove necessary and sufficient conditions for convergence. It is shown that when the system matrices of an implicit system are sparse, the implicit Kalman filter requires significantly less computer time and storage to implement as compared to the traditional explicit Kalman filter. Simulation results are presented to illustrate and substantiate the theoretical developments.

The FCF Fluids Integrated Rack: Microgravity Fluid Physics Experimentation on Board the ISS

NASA Technical Reports Server (NTRS)

Gati, Frank G.; Hill, Myron E.; SaintOnge, Tom (Technical Monitor)

2001-01-01

The Fluids Integrated Rack (FIR) is a modular, multi-user scientific research facility that will fly in the U.S. laboratory module, Destiny, of the International Space Station (ISS). The FIR will be one of the racks that will constitute the Fluids and Combustion Facility (FCF). The ISS will provide the FCF and therefore the FIR with the necessary resources, such as power and cooling, so that the FIR can carry out its primary mission of accommodating fluid physics science experiments. This paper discusses the mission, design, and the capabilities of the FIR in carrying out research on the ISS.

The heating of dust in starburst galaxies: The contribution of the nonionizing radiation

NASA Technical Reports Server (NTRS)

Calzetti, D.; Bohlin, R. C.; Kinney, Anne L.; Storchi-Bergmann, T.; Heckman, Timothy M.

1995-01-01

The IUE UV and optical spectra and the far-infrared (FIR) IRAS flux densities of a sample of starburst and blue compact galaxies are used to investigate the relationship between dust obscuration and dust emission. The amount of dust obscuration at UV wavelengths correlates with the FIR-to-blue ratio; and an analysis of the correlation indicates that not only the ionizing but also the nonionizing radiation contribute to the FIR emission. The amount of UV and optical energy lost to dust obscuration accounts for most of the cool dust FIUR emission and for about 70% of the warm dust FIR emission. The remaining 30% of the warm dust FIR flux is probably due to dust emission from regions of star formation which are embedded in opaque giant molecular clouds and do not contribute to the integrated UV and optical spectrum. The use of the FIR emission as an indicator of high-mass star formation rate in star-forming galaxies can be problematic, since the contribution to the FIR flux from cool dust emission heated by relatively old stars is nonnegligible.

Lumber recovery and deterioration of beetle-killed douglas-fir and grand fir in the Blue Mountains of eastern Oregon. Forest Service general technical report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Parry, D.L.; Filip, G.M.; Willits, S.A.

1996-09-01

The purpose of this study was to determine the effect of time since death over a 4-year period on the amount of usable product volume and value, and to determine the species of fungi associated with wood deterioration in the stems of Douglas-fir and grand fir trees killed by bark beetles in northeastern Oregon.

Growth of suppressed grand fir and Shasta red fir in central Oregon after release and thinning—10-year results.

Treesearch

Kenneth W. Seidel

1983-01-01

A 43-year-old, even-aged stand of advance reproduction of grand fir and Shasta red fir in central Oregon responded to release and thinning with diameter and height growth two to three times the prerelease rate. The response began immediately after the overstory was killed with 2,4-D. Diameter growth during the second 5 years after release increased significantly over...

Lumber recovery and deterioration of beetle-killed Douglas-fir and grand fir in the Blue Mountains of eastern Oregon.

Treesearch

Dean L. Parry; Gregory M. Filip; Susan A. Willits; Catherine G. Parks

1996-01-01

The purpose of this study was to determine the effect of time since death over a 4-year period on the amount of usable product volume and value, and to determine the species of fungi associated with wood deterioration in the stems of Douglas-fir and grand fir trees killed by bark beetles in northeastern Oregon. Sap rot, caused principally by Cryptoporus...

Tunable far infrared laser spectrometers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Blake, G.A.; Laughlin, K.B.; Cohen, R.C.

The state of the art in far infrared (FIR) spectroscopy is reviewed. The development of tunable, coherent FIR radiation sources is discussed. Applications of tunable FIR laser spectrometers for measurement of rotational spectra and dipole moments of molecular ions and free radicals, vibration-rotation-tunneling (VRT) spectra of weakly bound complexes, and vibration-rotation spectra of linear carbon clusters are presented. A detailed description of the Berkeley tunable FIR laser spectrometers is presented in the following article.

Far infrared radiation (FIR): its biological effects and medical applications

PubMed Central

Vatansever, Fatma; Hamblin, Michael R.

2013-01-01

Far infrared (FIR) radiation (λ = 3–100 μm) is a subdivision of the electromagnetic spectrum that has been investigated for biological effects. The goal of this review is to cover the use of a further sub-division (3– 12 μm) of this waveband, that has been observed in both in vitro and in vivo studies, to stimulate cells and tissue, and is considered a promising treatment modality for certain medical conditions. Technological advances have provided new techniques for delivering FIR radiation to the human body. Specialty lamps and saunas, delivering pure FIR radiation (eliminating completely the near and mid infrared bands), have became safe, effective, and widely used sources to generate therapeutic effects. Fibers impregnated with FIR emitting ceramic nanoparticles and woven into fabrics, are being used as garments and wraps to generate FIR radiation, and attain health benefits from its effects. PMID:23833705

Implementation of the Montreal Process: An Oregon Case Study

Treesearch

J. E. Brown

2006-01-01

The state of Oregon has about 28 million acres of forestland. The west side of the state is dominated by Douglas-fir forests, and most of the east side forests are occupied by Ponderosa pines or mixed conifers. The Oregon Board of Forestry is charged with making policy for Oregon’s forests. It has relied on quantitative assessments of forest conditions for many years,...

A Radio Study of the Ultra-luminous FIR Galaxy NGC 6240

NASA Astrophysics Data System (ADS)

Colbert, E.; Wilson, A. S.; Bland-Hawthorn, J.

1993-05-01

A number of galaxies observed in the IRAS mission are noted to emit ~ 99% of their bolometric flux in the FIR, with FIR luminosities in excess of 10(11) Lsun. The interacting galaxy NGC 6240 has often been referred to as the ``proto-typical'' ultra-luminous (L_FIR >~ 10(12) Lsun) FIR galaxy. The origin of the FIR excess remains a disputed subject in the literature. New observations of NGC 6240 were taken with the VLA at 20cm in the B-configuration, and at 3.6cm in the A-configuration. No significant radio emission was detected from or near the possible ultra-massive ``dark core'' hypothesized by Bland-Hawthorn et. al. (1991); however, approximately 30% of Seyfert galaxies have 20 cm radio luminosities weaker than the upper limit derived from the radio maps. The non-thermal radio emission from luminous FIR galaxies is tightly correlated with the FIR emission. Previous radio observations of NGC 6240 revealed two compact, steep-spectrum nuclear sources, nearly coincident with the two nuclear sources seen in optical images. The 2 images from the new VLA observations and 5 images from previous VLA observations are used to identify the morphological and spectral features of the strong, compact components in the nuclear regions (<~ 1.5 kpc; D=100 Mpc) and of the weaker ``clumps'' of diffuse emission south and west (>~ 3 kpc) from the nucleus. Feasible explanations for the radio emission are discussed. The models that have been proposed in the literature for the FIR excess of NGC 6240 are evaluated for consistency with the observed radio emission.

RADIO IMAGING OF THE NGC 2024 FIR 5/6 REGION: A HYPERCOMPACT H II REGION CANDIDATE IN ORION

DOE Office of Scientific and Technical Information (OSTI.GOV)

Choi, Minho; Kang, Miju; Lee, Jeong-Eun, E-mail: minho@kasi.re.kr

The NGC 2024 FIR 5/6 region was observed in the 6.9 mm continuum with an angular resolution of about 1.5 arcsec. The 6.9 mm continuum map shows four compact sources, FIR 5w, 5e, 6c, and 6n, as well as an extended structure of the ionization front associated with the optical nebulosity. FIR 6c has a source size of about 0.4 arcsec or 150 AU. The spectral energy distribution (SED) of FIR 6c is peculiar: rising steeply around 6.9 mm and flat around 1 mm. The possibility of a hypercompact H II region is explored. If the millimeter flux of FIRmore » 6c comes from hot ionized gas heated by a single object at the center, the central object may be a B1 star of about 5800 solar luminosities and about 13 solar masses. The 6.9 mm continuum of FIR 6n may be a mixture of free-free emission and dust continuum emission. Archival data show that both FIR 6n and 6c exhibit water maser activity, suggesting the existence of shocked gas around them. The 6.9 mm continuum emission from FIR 5w has a size of about 1.8 arcsec or 760 AU. The SEDs suggest that the 6.9 mm emission of FIR 5w and 5e comes from dust, and the masses of the dense molecular gas are about 0.6 and 0.5 solar masses, respectively.« less

Movement of elements into the atmosphere from coniferous trees in subalpine forests of colorado and Idaho

USGS Publications Warehouse

Curtin, G.C.; King, H.D.; Mosier, E.L.

1974-01-01

Exudates from conifer trees, presumably consisting largely of volatile materials, were sampled at 19 subalpine localitites in Colorado and Idaho where anomalous amounts of several metals were determined in vegetation and mull during previous geochemical testing. The trees sampled were lodgepole pine (Pinus contorta), Engelmann spruce (Picea engelmannii) and Douglas fir (Pseudotsuga menziesii). The condensed exudates were passed through No. 40 Whatman filters, and through 5-micron, 0.45-micron, and 0.05-micron average-pore-diameter membrane filters, evaporated to dryness, and each residue was ashed and analyzed by a semiquantitative spectrographic method. The ashed residues of the exudates contain lithium, beryllium, boron, sodium, magnesium, titanium, vanadium, chromium, manganese, iron, cobalt, nickel, copper, zinc, gallium, arsenic, strontium, yttrium, zirconium, molybdenum, silver, lead, bismuth, cadmium, tin, antimony, barium, and lanthanum. The presence of these elements suggests that volatile exudates from vegetation are a medium for the transport of elements in the biogeochemical cycle in subalpine environments. Thus, air sampling and analysis of aerosols derived from volatile exudates may be a useful tool in geochemical exploration. ?? 1974.

Continuous Mass Measurement on Conveyor Belt

NASA Astrophysics Data System (ADS)

Tomobe, Yuki; Tasaki, Ryosuke; Yamazaki, Takanori; Ohnishi, Hideo; Kobayashi, Masaaki; Kurosu, Shigeru

The continuous mass measurement of packages on a conveyor belt will become greatly important. In the mass measurement, the sequence of products is generally random. An interesting possibility of raising throughput of the conveyor line without increasing the conveyor belt speed is offered by the use of two or three conveyor belt scales (called a multi-stage conveyor belt scale). The multi-stage conveyor belt scale can be created which will adjust the conveyor belt length to the product length. The conveyor belt scale usually has maximum capacities of less than 80kg and 140cm, and achieves measuring rates of more than 150 packages per minute and more. The output signals from the conveyor belt scale are always contaminated with noises due to vibrations of the conveyor and the product to be measured in motion. In this paper an employed digital filter is of Finite Impulse Response (FIR) type designed under the consideration on the dynamics of the conveyor system. The experimental results on the conveyor belt scale suggest that the filtering algorithms are effective enough to practical applications to some extent.

Programmable noise bandwidth reduction by means of digital averaging

NASA Technical Reports Server (NTRS)

Poklemba, John J. (Inventor)

1993-01-01

Predetection noise bandwidth reduction is effected by a pre-averager capable of digitally averaging the samples of an input data signal over two or more symbols, the averaging interval being defined by the input sampling rate divided by the output sampling rate. As the averaged sample is clocked to a suitable detector at a much slower rate than the input signal sampling rate the noise bandwidth at the input to the detector is reduced, the input to the detector having an improved signal to noise ratio as a result of the averaging process, and the rate at which such subsequent processing must operate is correspondingly reduced. The pre-averager forms a data filter having an output sampling rate of one sample per symbol of received data. More specifically, selected ones of a plurality of samples accumulated over two or more symbol intervals are output in response to clock signals at a rate of one sample per symbol interval. The pre-averager includes circuitry for weighting digitized signal samples using stored finite impulse response (FIR) filter coefficients. A method according to the present invention is also disclosed.

7 CFR 301.92-2 - Restricted, regulated, and associated articles; lists of proven hosts and associated plant taxa.

Code of Federal Regulations, 2012 CFR

2012-01-01

... willow *Sequoia sempervirens Coast redwood *Syringa vulgaris Lilac *Taxus baccata European yew... Phytophthora ramorum: Abies concolor White fir Abies grandis Grand fir Abies magnifica Red fir Acer circinatum...

7 CFR 301.92-2 - Restricted, regulated, and associated articles; lists of proven hosts and associated plant taxa.

Code of Federal Regulations, 2013 CFR

2013-01-01

... willow *Sequoia sempervirens Coast redwood *Syringa vulgaris Lilac *Taxus baccata European yew... Phytophthora ramorum: Abies concolor White fir Abies grandis Grand fir Abies magnifica Red fir Acer circinatum...

7 CFR 301.92-2 - Restricted, regulated, and associated articles; lists of proven hosts and associated plant taxa.

Code of Federal Regulations, 2014 CFR

2014-01-01

... willow *Sequoia sempervirens Coast redwood *Syringa vulgaris Lilac *Taxus baccata European yew... Phytophthora ramorum: Abies concolor White fir Abies grandis Grand fir Abies magnifica Red fir Acer circinatum...

7 CFR 301.92-2 - Restricted, regulated, and associated articles; lists of proven hosts and associated plant taxa.

Code of Federal Regulations, 2010 CFR

2010-01-01

... willow *Sequoia sempervirens Coast redwood *Syringa vulgaris Lilac *Taxus baccata European yew... Phytophthora ramorum: Abies concolor White fir Abies grandis Grand fir Abies magnifica Red fir Acer circinatum...

7 CFR 301.92-2 - Restricted, regulated, and associated articles; lists of proven hosts and associated plant taxa.

Code of Federal Regulations, 2011 CFR

2011-01-01

... willow *Sequoia sempervirens Coast redwood *Syringa vulgaris Lilac *Taxus baccata European yew... Phytophthora ramorum: Abies concolor White fir Abies grandis Grand fir Abies magnifica Red fir Acer circinatum...

Efficient color display using low-absorption in-pixel color filters

NASA Technical Reports Server (NTRS)

Wang, Yu (Inventor)

2000-01-01

A display system having a non-absorbing and reflective color filtering array and a reflector to improve light utilization efficiency. One implementation of the color filtering array uses a surface plasmon filter having two symmetric metal-dielectric interfaces coupled with each other to produce a transmission optical wave at a surface plasmon resonance wavelength at one interface from a p-polarized input beam on the other interface. Another implementation of the color filtering array uses a metal-film interference filter having two dielectric layers and three metallic films.

Far-infrared properties of cluster galaxies

NASA Technical Reports Server (NTRS)

Bicay, M. D.; Giovanelli, R.

1987-01-01

Far-infrared properties are derived for a sample of over 200 galaxies in seven clusters: A262, Cancer, A1367, A1656 (Coma), A2147, A2151 (Hercules), and Pegasus. The IR-selected sample consists almost entirely of IR normal galaxies, with Log of L(FIR) = 9.79 solar luminosities, Log of L(FIR)/L(B) = 0,79, and Log of S(100 microns)/S(60 microns) = 0.42. None of the sample galaxies has Log of L(FIR) greater than 11.0 solar luminosities, and only one has a FIR-to-blue luminosity ratio greater than 10. No significant differences are found in the FIR properties of HI-deficient and HI-normal cluster galaxies.

Tree-ring stable isotopes record the impact of a foliar fungal pathogen on CO(2) assimilation and growth in Douglas-fir.

PubMed

Saffell, Brandy J; Meinzer, Frederick C; Voelker, Steven L; Shaw, David C; Brooks, J Renée; Lachenbruch, Barbara; McKay, Jennifer

2014-07-01

Swiss needle cast (SNC) is a fungal disease of Douglas-fir (Pseudotsuga menziesii) that has recently become prevalent in coastal areas of the Pacific Northwest. We used growth measurements and stable isotopes of carbon and oxygen in tree-rings of Douglas-fir and a non-susceptible reference species (western hemlock, Tsuga heterophylla) to evaluate their use as proxies for variation in past SNC infection, particularly in relation to potential explanatory climate factors. We sampled trees from an Oregon site where a fungicide trial took place from 1996 to 2000, which enabled the comparison of stable isotope values between trees with and without disease. Carbon stable isotope discrimination (Δ(13)C) of treated Douglas-fir tree-rings was greater than that of untreated Douglas-fir tree-rings during the fungicide treatment period. Both annual growth and tree-ring Δ(13)C increased with treatment such that treated Douglas-fir had values similar to co-occurring western hemlock during the treatment period. There was no difference in the tree-ring oxygen stable isotope ratio between treated and untreated Douglas-fir. Tree-ring Δ(13)C of diseased Douglas-fir was negatively correlated with relative humidity during the two previous summers, consistent with increased leaf colonization by SNC under high humidity conditions that leads to greater disease severity in following years. © 2013 John Wiley & Sons Ltd.

Far-infrared suppresses skin photoaging in ultraviolet B-exposed fibroblasts and hairless mice

PubMed Central

Chiu, Hui-Wen; Chen, Cheng-Hsien; Chen, Yi-Jie; Hsu, Yung-Ho

2017-01-01

Ultraviolet (UV) induces skin photoaging, which is characterized by thickening, wrinkling, pigmentation, and dryness. Collagen, which is one of the main building blocks of human skin, is regulated by collagen synthesis and collagen breakdown. Autophagy was found to block the epidermal hyperproliferative response to UVB and may play a crucial role in preventing skin photoaging. In the present study, we investigated whether far-infrared (FIR) therapy can inhibit skin photoaging via UVB irradiation in NIH 3T3 mouse embryonic fibroblasts and SKH-1 hairless mice. We found that FIR treatment significantly increased procollagen type I through the induction of the TGF-β/Smad axis. Furthermore, UVB significantly enhanced the expression of matrix metalloproteinase-1 (MMP-1) and MMP-9. FIR inhibited UVB-induced MMP-1 and MMP-9. Treatment with FIR reversed UVB-decreased type I collagen. In addition, FIR induced autophagy by inhibiting the Akt/mTOR signaling pathway. In UVB-induced skin photoaging in a hairless mouse model, FIR treatment resulted in decreased skin thickness in UVB irradiated mice and inhibited the degradation of collagen fibers. Moreover, FIR can increase procollagen type I via the inhibition of MMP-9 and induction of TGF-β in skin tissues. Therefore, our study provides evidence for the beneficial effects of FIR exposure in a model of skin photoaging. PMID:28301572

Detecting Structural Failures Via Acoustic Impulse Responses

NASA Technical Reports Server (NTRS)

Bayard, David S.; Joshi, Sanjay S.

1995-01-01

Advanced method of acoustic pulse reflectivity testing developed for use in determining sizes and locations of failures within structures. Used to detect breaks in electrical transmission lines, detect faults in optical fibers, and determine mechanical properties of materials. In method, structure vibrationally excited with acoustic pulse (a "ping") at one location and acoustic response measured at same or different location. Measured acoustic response digitized, then processed by finite-impulse-response (FIR) filtering algorithm unique to method and based on acoustic-wave-propagation and -reflection properties of structure. Offers several advantages: does not require training, does not require prior knowledge of mathematical model of acoustic response of structure, enables detection and localization of multiple failures, and yields data on extent of damage at each location.

Adaptive frequency-domain equalization in digital coherent optical receivers.

PubMed

Faruk, Md Saifuddin; Kikuchi, Kazuro

2011-06-20

We propose a novel frequency-domain adaptive equalizer in digital coherent optical receivers, which can reduce computational complexity of the conventional time-domain adaptive equalizer based on finite-impulse-response (FIR) filters. The proposed equalizer can operate on the input sequence sampled by free-running analog-to-digital converters (ADCs) at the rate of two samples per symbol; therefore, the arbitrary initial sampling phase of ADCs can be adjusted so that the best symbol-spaced sequence is produced. The equalizer can also be configured in the butterfly structure, which enables demultiplexing of polarization tributaries apart from equalization of linear transmission impairments. The performance of the proposed equalization scheme is verified by 40-Gbits/s dual-polarization quadrature phase-shift keying (QPSK) transmission experiments.

Symmetric convolution of asymmetric multidimensional sequences using discrete trigonometric transforms.

PubMed

Foltz, T M; Welsh, B M

1999-01-01

This paper uses the fact that the discrete Fourier transform diagonalizes a circulant matrix to provide an alternate derivation of the symmetric convolution-multiplication property for discrete trigonometric transforms. Derived in this manner, the symmetric convolution-multiplication property extends easily to multiple dimensions using the notion of block circulant matrices and generalizes to multidimensional asymmetric sequences. The symmetric convolution of multidimensional asymmetric sequences can then be accomplished by taking the product of the trigonometric transforms of the sequences and then applying an inverse trigonometric transform to the result. An example is given of how this theory can be used for applying a two-dimensional (2-D) finite impulse response (FIR) filter with nonlinear phase which models atmospheric turbulence.

Complementary filter implementation in the dynamic language Lua

NASA Astrophysics Data System (ADS)

Sadowski, Damian; Sawicki, Aleksander; Lukšys, Donatas; Slanina, Zdenek

2017-08-01

The article presents the complementary filter implementation, that is used for the estimation of the pitch angle, in Lua script language. Inertial sensors as accelerometer and gyroscope were used in the study. Methods of angles estimation using acceleration and angular velocity sensors were presented in the theoretical part of the article. The operating principle of complementary filter has been presented. The prototype of Butterworth's analogue filter and its digital equivalent have been designed. Practical implementation of the issue was performed with the use of PC and DISCOVERY evaluation board equipped with STM32F01 processor, L3GD20 gyroscope and LS303DLHC accelerometer. Measurement data was transmitted by UART serial interface, then processed with the use of Lua software and luaRS232 programming library. Practical implementation was divided into two stages. In the first part, measurement data has been recorded and then processed with help of a complementary filter. In the second step, coroutines mechanism was used to filter data in real time.

Thinning, tree-growth, and resistance to multi-year drought in a mixed-conifer forest of northern California

USGS Publications Warehouse

Vernon, Michael J.; Sherriff, Rosemary L.; van Mantgem, Phillip; Kane, Jeffrey M.

2018-01-01

Drought is an important stressor in forest ecosystems that can influence tree vigor and survival. In the U.S., forest managers use two primary management techniques to promote resistance and resilience to drought: prescribed fire and mechanical thinning. Generally applied to reduce fuels and fire hazard, treatments may also reduce competition for resources that may improve tree-growth and reduce mortality during drought. A recent severe and prolonged drought in California provided a natural experiment to investigate tree-growth responses to fuel treatments and climatic stress. We assessed tree-growth from 299 ponderosa pine (Pinus ponderosa) and Douglas-fir (Pseudotsuga menziesii) in treated and untreated stands during severe drought from 2012 to 2015 in the mixed-conifer forests of Whiskeytown National Recreation Area (WNRA) in northern California. The treatment implemented at WNRA removed 34% of live basal area through mechanical thinning with a subsequent pile burning of residual fuels. Tree-growth was positively associated with crown ratio and negatively associated with competition and a 1-year lag of climate water deficit, an index of drought. Douglas-fir generally had higher annual growth than ponderosa pine, although factors affecting growth were the same for both species. Drought resistance, expressed as the ratio between mean growth during drought and mean growth pre-drought, was higher in treated stands compared to untreated stands during both years of severe drought (2014 and 2015) for ponderosa pine but only one year (2014) for Douglas-fir. Thinning improved drought resistance, but tree size, competition and species influenced this response. On-going thinning treatments focused on fuels and fire hazard reduction are likely to be effective at promoting growth and greater drought resistance in dry mixed-conifer forests. Given the likelihood of future droughts, land managers may choose to implement similar treatments to reduce potential impacts.

Active Control of Wind Tunnel Noise

NASA Technical Reports Server (NTRS)

Hollis, Patrick (Principal Investigator)

1991-01-01

The need for an adaptive active control system was realized, since a wind tunnel is subjected to variations in air velocity, temperature, air turbulence, and some other factors such as nonlinearity. Among many adaptive algorithms, the Least Mean Squares (LMS) algorithm, which is the simplest one, has been used in an Active Noise Control (ANC) system by some researchers. However, Eriksson's results, Eriksson (1985), showed instability in the ANC system with an ER filter for random noise input. The Restricted Least Squares (RLS) algorithm, although computationally more complex than the LMS algorithm, has better convergence and stability properties. The ANC system in the present work was simulated by using an FIR filter with an RLS algorithm for different inputs and for a number of plant models. Simulation results for the ANC system with acoustic feedback showed better robustness when used with the RLS algorithm than with the LMS algorithm for all types of inputs. Overall attenuation in the frequency domain was better in the case of the RLS adaptive algorithm. Simulation results with a more realistic plant model and an RLS adaptive algorithm showed a slower convergence rate than the case with an acoustic plant as a delay plant. However, the attenuation properties were satisfactory for the simulated system with the modified plant. The effect of filter length on the rate of convergence and attenuation was studied. It was found that the rate of convergence decreases with increase in filter length, whereas the attenuation increases with increase in filter length. The final design of the ANC system was simulated and found to have a reasonable convergence rate and good attenuation properties for an input containing discrete frequencies and random noise.

Generic Kalman Filter Software

NASA Technical Reports Server (NTRS)

Lisano, Michael E., II; Crues, Edwin Z.

2005-01-01

The Generic Kalman Filter (GKF) software provides a standard basis for the development of application-specific Kalman-filter programs. Historically, Kalman filters have been implemented by customized programs that must be written, coded, and debugged anew for each unique application, then tested and tuned with simulated or actual measurement data. Total development times for typical Kalman-filter application programs have ranged from months to weeks. The GKF software can simplify the development process and reduce the development time by eliminating the need to re-create the fundamental implementation of the Kalman filter for each new application. The GKF software is written in the ANSI C programming language. It contains a generic Kalman-filter-development directory that, in turn, contains a code for a generic Kalman filter function; more specifically, it contains a generically designed and generically coded implementation of linear, linearized, and extended Kalman filtering algorithms, including algorithms for state- and covariance-update and -propagation functions. The mathematical theory that underlies the algorithms is well known and has been reported extensively in the open technical literature. Also contained in the directory are a header file that defines generic Kalman-filter data structures and prototype functions and template versions of application-specific subfunction and calling navigation/estimation routine code and headers. Once the user has provided a calling routine and the required application-specific subfunctions, the application-specific Kalman-filter software can be compiled and executed immediately. During execution, the generic Kalman-filter function is called from a higher-level navigation or estimation routine that preprocesses measurement data and post-processes output data. The generic Kalman-filter function uses the aforementioned data structures and five implementation- specific subfunctions, which have been developed by the user on the basis of the aforementioned templates. The GKF software can be used to develop many different types of unfactorized Kalman filters. A developer can choose to implement either a linearized or an extended Kalman filter algorithm, without having to modify the GKF software. Control dynamics can be taken into account or neglected in the filter-dynamics model. Filter programs developed by use of the GKF software can be made to propagate equations of motion for linear or nonlinear dynamical systems that are deterministic or stochastic. In addition, filter programs can be made to operate in user-selectable "covariance analysis" and "propagation-only" modes that are useful in design and development stages.

A SNP resource for Douglas-fir: de novo transcriptome assembly and SNP detection and validation.

PubMed

Howe, Glenn T; Yu, Jianbin; Knaus, Brian; Cronn, Richard; Kolpak, Scott; Dolan, Peter; Lorenz, W Walter; Dean, Jeffrey F D

2013-02-28

Douglas-fir (Pseudotsuga menziesii), one of the most economically and ecologically important tree species in the world, also has one of the largest tree breeding programs. Although the coastal and interior varieties of Douglas-fir (vars. menziesii and glauca) are native to North America, the coastal variety is also widely planted for timber production in Europe, New Zealand, Australia, and Chile. Our main goal was to develop a SNP resource large enough to facilitate genomic selection in Douglas-fir breeding programs. To accomplish this, we developed a 454-based reference transcriptome for coastal Douglas-fir, annotated and evaluated the quality of the reference, identified putative SNPs, and then validated a sample of those SNPs using the Illumina Infinium genotyping platform. We assembled a reference transcriptome consisting of 25,002 isogroups (unique gene models) and 102,623 singletons from 2.76 million 454 and Sanger cDNA sequences from coastal Douglas-fir. We identified 278,979 unique SNPs by mapping the 454 and Sanger sequences to the reference, and by mapping four datasets of Illumina cDNA sequences from multiple seed sources, genotypes, and tissues. The Illumina datasets represented coastal Douglas-fir (64.00 and 13.41 million reads), interior Douglas-fir (80.45 million reads), and a Yakima population similar to interior Douglas-fir (8.99 million reads). We assayed 8067 SNPs on 260 trees using an Illumina Infinium SNP genotyping array. Of these SNPs, 5847 (72.5%) were called successfully and were polymorphic. Based on our validation efficiency, our SNP database may contain as many as ~200,000 true SNPs, and as many as ~69,000 SNPs that could be genotyped at ~20,000 gene loci using an Infinium II array-more SNPs than are needed to use genomic selection in tree breeding programs. Ultimately, these genomic resources will enhance Douglas-fir breeding and allow us to better understand landscape-scale patterns of genetic variation and potential responses to climate change.

A SNP resource for Douglas-fir: de novo transcriptome assembly and SNP detection and validation

PubMed Central

2013-01-01

Background Douglas-fir (Pseudotsuga menziesii), one of the most economically and ecologically important tree species in the world, also has one of the largest tree breeding programs. Although the coastal and interior varieties of Douglas-fir (vars. menziesii and glauca) are native to North America, the coastal variety is also widely planted for timber production in Europe, New Zealand, Australia, and Chile. Our main goal was to develop a SNP resource large enough to facilitate genomic selection in Douglas-fir breeding programs. To accomplish this, we developed a 454-based reference transcriptome for coastal Douglas-fir, annotated and evaluated the quality of the reference, identified putative SNPs, and then validated a sample of those SNPs using the Illumina Infinium genotyping platform. Results We assembled a reference transcriptome consisting of 25,002 isogroups (unique gene models) and 102,623 singletons from 2.76 million 454 and Sanger cDNA sequences from coastal Douglas-fir. We identified 278,979 unique SNPs by mapping the 454 and Sanger sequences to the reference, and by mapping four datasets of Illumina cDNA sequences from multiple seed sources, genotypes, and tissues. The Illumina datasets represented coastal Douglas-fir (64.00 and 13.41 million reads), interior Douglas-fir (80.45 million reads), and a Yakima population similar to interior Douglas-fir (8.99 million reads). We assayed 8067 SNPs on 260 trees using an Illumina Infinium SNP genotyping array. Of these SNPs, 5847 (72.5%) were called successfully and were polymorphic. Conclusions Based on our validation efficiency, our SNP database may contain as many as ~200,000 true SNPs, and as many as ~69,000 SNPs that could be genotyped at ~20,000 gene loci using an Infinium II array—more SNPs than are needed to use genomic selection in tree breeding programs. Ultimately, these genomic resources will enhance Douglas-fir breeding and allow us to better understand landscape-scale patterns of genetic variation and potential responses to climate change. PMID:23445355

The Fluids Integrated Rack and Light Microscopy Module Integrated Capabilities

NASA Technical Reports Server (NTRS)

Motil, Susan M.; Gati, Frank; Snead, John H.; Hill, Myron E.; Griffin, DeVon W.

2003-01-01

The Fluids Integrated Rack (FIR), a facility class payload, and the Light Microscopy Module (LMM), a subrack payload, are scheduled to be launched in 2005. The LMM integrated into the FIR will provide a unique platform for conducting fluids and biological experiments on ISS. The FIR is a modular, multi-user scientific research facility that will fly in the U.S. laboratory module, Destiny, of the International Space Station (ISS). The first payload in the FIR will be the Light Microscopy Module (LMM). The LMM is planned as a remotely controllable, automated, on-orbit microscope subrack facility, allowing flexible scheduling and control of fluids and biology experiments within the FIR. Key diagnostic capabilities for meeting science requirements include video microscopy to observe microscopic phenomena and dynamic interactions, interferometry to make thin film measurements with nanometer resolution, laser tweezers for particle manipulation, confocal microscopy to provide enhanced three-dimensional visualization of structures, and spectrophotometry to measure photonic properties of materials. The LMM also provides experiment sample containment for frangibles and fluids. This paper will provide a description of the current FIR and LMM designs, planned capabilities and key features. In addition a brief description of the initial five experiments planned for LMM/FIR will be provided.

Price projections for selected grades of Douglas-fir lumber.

Treesearch

Richard W. Haynes; Thomas D. Fahey; Roger D. Fight

1988-01-01

Grade-specific price projections were developed for Douglas-fir lumber produced in the Douglas-fir region. These grade-specific price projections can be used as an aid in evaluating management practices that will affect the quality of saw logs that are produced.

Predictions of fire behavior and resistance to control: for use with photo series for the Douglas fir-hemlock type and the coastal Douglas-fir-hardwood type.

Treesearch

David V. SANDBERG; Franklin R. Ward

1981-01-01

This publication presents tables on the behavior of fire and the resistance of fuels to control. The information is to be used with the photos in the publication, "Photo Series for Quantifying Forest Residues in the Coastal Douglas-fir—Hemlock Type, Coastal Douglas-fir—Hardwood Type" (Maxwell, Wayne G.; Ward, Franklin R. 1976. Gen. Tech. Rep. PNW-GTR-051....

Fluids and Combustion Facility: Fluids Integrated Rack Modal Model Correlation

NASA Technical Reports Server (NTRS)

McNelis, Mark E.; Suarez, Vicente J.; Sullivan, Timothy L.; Otten, Kim D.; Akers, James C.

2005-01-01

The Fluids Integrated Rack (FIR) is one of two racks in the Fluids and Combustion Facility on the International Space Station. The FIR is dedicated to the scientific investigation of space system fluids management supporting NASA s Exploration of Space Initiative. The FIR hardware was modal tested and FIR finite element model updated to satisfy the International Space Station model correlation criteria. The final cross-orthogonality results between the correlated model and test mode shapes was greater than 90 percent for all primary target modes.

Litter dynamics in two Sierran mixed conifer forests. I. Litterfall and decomposition rates

USGS Publications Warehouse

Stohlgren, Thomas J.

1988-01-01

Litterfall was measured for 4 years and leaf litter decomposition rates were studied for 3.6 years in two mixed conifer forest (giant sequoia-fir and fir-pine) in the southern Sierra Nevada of California. The giant sequoia-fir forest (GS site) was dominated by giant sequoia (Sequoiadendron giganteum (Lindl.) Buchh.), white fir (Abies concolor Lindl. & Gord.), and sugar pine (Pinus lambertiana Dougl.). The fir-pine forest (FP site) was dominated by white fir, sugar pine, and incense cedar (Calocedrus decurrens (Torr.) Florin). Litterfall, including large woody debris -1•year-1 compared with 4355 kg•ha-1•year-1 at the FP site (3.4:1). In the GS site, leaf litter decomposition after 3.6 years was slowest for giant sequoia (28.2% mass loss), followed by sugar pine (34.3%) and white fie (45.1%). In the FP site, mass loss was slowest for sugar pine (40.0%), followed by white fir (45.1%), while incense cedar showed the greatest mass loss (56.9%) after 3.6 years. High litterfall rates of large woody debris (i.e., 2.5-15.2 cm diameter) and slow rates of leaf litter decomposition in the giant sequoia-fir forest type may result in higher litter accumulation rates than in the fir-pine type. Leaf litter times to 95% decay for the GS and FP sites were 30 and 27 years, respectively, if the initial 0.7-year period (a short period of rapid mass decay) was ignored in the calculation. A mass balance approach for total litterfall (<15.2 cm diameter) decomposition yielded lower decay constants than did the litterbag study and therefore longer times to 95% decay (57 years for the GS site and 62 years for the FP site).

Simulation of synthetic discriminant function optical implementation

NASA Astrophysics Data System (ADS)

Riggins, J.; Butler, S.

1984-12-01

The optical implementation of geometrical shape and synthetic discriminant function matched filters is computer modeled. The filter implementation utilizes the Allebach-Keegan computer-generated hologram algorithm. Signal-to-noise and efficiency measurements were made on the resultant correlation planes.

A VHDL Core for Intrinsic Evolution of Discrete Time Filters with Signal Feedback

NASA Technical Reports Server (NTRS)

Gwaltney, David A.; Dutton, Kenneth

2005-01-01

The design of an Evolvable Machine VHDL Core is presented, representing a discrete-time processing structure capable of supporting control system applications. This VHDL Core is implemented in an FPGA and is interfaced with an evolutionary algorithm implemented in firmware on a Digital Signal Processor (DSP) to create an evolvable system platform. The salient features of this architecture are presented. The capability to implement IIR filter structures is presented along with the results of the intrinsic evolution of a filter. The robustness of the evolved filter design is tested and its unique characteristics are described.

Atomic and molecular far-infrared lines from high redshift galaxies

NASA Astrophysics Data System (ADS)

Vallini, L.

2015-03-01

The advent of Atacama Large Millimeter-submillimeter Array (ALMA), with its unprecedented sensitivity, makes it possible the detection of far-infrared (FIR) metal cooling and molecular lines from the first galaxies that formed after the Big Bang. These lines represent a powerful tool to shed light on the physical properties of the interstellar medium (ISM) in high-redshift sources. In what follows we show the potential of a physically motivated theoretical approach that we developed to predict the ISM properties of high redshift galaxies. The model allows to infer, as a function of the metallicity, the luminosities of various FIR lines observable with ALMA. It is based on high resolution cosmological simulations of star-forming galaxies at the end of the Epoch of Reionization (z˜eq6) , further implemented with sub-grid physics describing the cooling and the heating processes that take place in the neutral diffuse ISM. Finally we show how a different approach based on semi-analytical calculations can allow to predict the CO flux function at z>6.

Aboveground growth interactions of paired conifer seedlings in close proximity

Treesearch

Warren D. Devine; Timothy B. Harrington

2011-01-01

Where belowground resources are relatively abundant, naturally established trees sometimes occur in very close proximity to one another. We conducted a two-year study to assess the aboveground interactions between Douglas-fir (Pseudotsuga menziesii), grand fir (Abies grandis) and noble fir (Abies procera)...

Early genetic testing of coastal Douglas-fir for Swiss needle cast tolerance.

Treesearch

Fatih Temel; G.R. Johnson; W.T. Adams

2005-01-01

The possibility of early testing coastal Douglas-fir (Pseudotsuga menziesii var. menziesii (Mirb.) Franco) for Swiss needle cast (SNC; caused by Phaeocryptopus gaeumannii (Rohde) Petrak) tolerance was investigated using 55 Douglas-fir families from western Oregon. Seedlings were inoculated with P...

Technology Development of Miniaturized Far-Infrared Sources for Biomolecular Spectroscopy

NASA Technical Reports Server (NTRS)

Kono, Junichiro

2003-01-01

The objective of this project was to develop a purely solid-state based, thus miniaturized, far-infrared (FIR) (also known as terahertz (THz)) wave source using III-V semiconductor nanostructures for biomolecular detection and sensing. Many biomolecules, such as DNA and proteins, have distinct spectroscopic features in the FIR wavelength range as a result of vibration-rotation-tunneling motions and various inter- and intra-molecule collective motions. Spectroscopic characterization of such molecules requires narrow linewidth, sufficiently high power, tunable (in wavelength), and coherent FIR sources. Unfortunately, the FIR frequency is one of the least technologically developed ranges in the electromagnetic spectrum. Currently available FIR sources based on non-solid state technology are bulky, inefficient, and very often incoherent. In this project we investigated antimonide based compound semiconductor (ABCS) nanostructures as the active medium to generate FIR radiation. The final goal of this project was to demonstrate a semiconductor THz source integrated with a pumping diode laser module to achieve a compact system for biomolecular applications.

Spectral Energy Distribution of Far-infrared Bright Quasar Sample in the Lockman Hole

NASA Astrophysics Data System (ADS)

Dai, Y.; Huang, J.-S.; Omont, A.; Hatziminaoglou, E.; Willmer, C.; Fazio, G.; Elvis, M.; Bergeron, J.; Rigopoulou, D.; Perez-Fournon, I.

2011-10-01

The far-infrared (FIR) properties of Quasi-Stellar Objects (QSOs) is important in connecting the Starburst (SB) and Active Galactic Nucleus (AGN) activities. Therefore, we constructed a 24 μ m selected QSO sample to study their FIR behavior. All sources were spectroscopically identified from MMT or the Sloan Digital Sky Survey (SDSS) as broadline quasars. Of the total ˜330 sources, 37 have secure FIR detections in the Herschel-HERMES field. We compared their SEDs to previous QSO templates, and found that those FIR bright quasars differ from existing AGNs only by an additional dust component(s). Further studies on the origin for the FIR emission reveals the relative roles starburst and AGN play in powering the dust emission, based on the dust temperature, FIR luminosity, and the shapes of individual SEDs. The dust temperatures have a wide range from 20K to 80K with a median of ˜ 30K, indicating homogeneous heating mechanisms that could later be related to the origin of these cold dust emissions.

Checking for Circular Dependencies in Distributed Stream Programs

DTIC Science & Technology

2011-08-29

extensions to express new complexities more conve- nient. Teleport messaging ( TMG ) in the StreamIt language [30] is an example. 1.1 StreamIt Language...dynamicities to an FIR computation Thies et al. in [30] give a TMG model for distributed stream pro- grams. TMG is a mechanism that implements control...messages for stream graphs. The TMG mechanism is designed not to interfere with original dataflow graphs’ structures and scheduling, therefore a key

Local Volume Hi Survey: the far-infrared radio correlation

NASA Astrophysics Data System (ADS)

Shao, Li; Koribalski, Bärbel S.; Wang, Jing; Ho, Luis C.; Staveley-Smith, Lister

2018-06-01

In this paper we measure the far-infrared (FIR) and radio flux densities of a sample of 82 local gas-rich galaxies, including 70 "dwarf" galaxies (M* < 109 M⊙), from the Local Volume HI Survey (LVHIS), which is close to volume limited. It is found that LVHIS galaxies hold a tight linear FIR-radio correlation (FRC) over four orders of magnitude (F_1.4GHz ∝ F_FIR^{1.00± 0.08}). However, for detected galaxies only, a trend of larger FIR-to-radio ratio with decreasing flux density is observed. We estimate the star formation rate by combining UV and mid-IR data using empirical calibration. It is confirmed that both FIR and radio emission are strongly connected with star formation but with significant non-linearity. Dwarf galaxies are found radiation deficient in both bands, when normalized by star formation rate. It urges a "conspiracy" to keep the FIR-to-radio ratio generally constant. By using partial correlation coefficient in Pearson definition, we identify the key galaxy properties associated with the FIR and radio deficiency. Some major factors, such as stellar mass surface density, will cancel out when taking the ratio between FIR and radio fluxes. The remaining factors, such as HI-to-stellar mass ratio and galaxy size, are expected to cancel each other due to the distribution of galaxies in the parameter space. Such cancellation is probably responsible for the "conspiracy" to keep the FRC alive.

Fir Decline and Mortality in the Southern Siberian Mountains

NASA Technical Reports Server (NTRS)

Kharuk, Viacheslav I.; Im, Sergei T.; Petrov, Ilya A.; Dvinskaya, Mariya, L.; Fedotova, Elena V.; Ranson, Kenneth J.

2016-01-01

Increased dieback and mortality of dark needle conifer (DNC) stands (composed of fir (Abies sibirica),Siberian pine (Pinus sibirica) and spruce (Picea obovata))were documented in Russia during recent decades. Here we analyzed spatial and temporal patterns of fir decline and mortality in the southern Siberian Mountains based on satellite, in situ and dendrochronological data. The studied stands are located within the boundary between DNC taiga to the north and forest-steppe to the south. Fir decline and mortality were observed to originate where topographic features contributed to maximal water-stress risk, i.e., steep (1825),convex, south-facing slopes with a shallow well-drained root zone. Fir regeneration survived droughts and increased stem radial growth, while upper canopy trees died. Tree ring width(TRW) growth negatively correlated with vapor pressure deficit (VPD), drought index and occurrence of late frosts, and positively with soil water content. Previous year growth conditions (i.e., drought index, VPD, soil water anomalies)have a high impact on current TRW (r 0.600.74). Fir mortality was induced by increased water stress and severe droughts (as a primary factor) in synergy with bark-beetles and fungi attacks (as secondary factors). Dendrochronology data indicated that fir mortality is a periodic process. In a future climate with increased aridity and drought frequency, fir (and Siberian pine) may disappear from portions of its current range (primarily within the boundary with the forest steppe)and is likely to be replaced by drought-tolerant species such as Pinus sylvestris and Larix sibirica.

Veneer recovery from peeler-grade Douglas-fir logs in western Washington.

Treesearch

E.H. Clarke; A.C. Knauss

1957-01-01

As Douglas-fir plywood production continues to expand, increased demands will be made for all grades of peelable Douglas-fir logs. Thus, it becomes increasingly important to know the veneer-grade recovery expected so that timber and logs can be more accurately appraised.

Biological research by optically pumped far infrared lasers

NASA Astrophysics Data System (ADS)

Zhengyu, Mi

1989-05-01

The FIR breeding for paddy rice, black bean and wheat, the chlorophyll mutation of paddy rice induced by optically pumped FIR laser, etc., are presented. The results of SDS electrophoresis analysis of soluble proteins of Drosophita melanrgaster irradiated by optically pumped FIR laser are described and discussed.

Dwarf mistletoe-infected red fir: growth after release

Treesearch

Robert F. Scharpf

1979-01-01

Release cutting, live crown ratio, diameter-at-breast height, and dwarf mistletoe (Arceuthobium abietinum f. sp. magnificae). acted to affect radial and height growth of red firs (Abies magnifica A. Murr.). Infected and noninfected red firs responded well to release as expressed by increased radial growth: growth...

Growing corkbark fir and subalpine fir for nursery production

USDA-ARS?s Scientific Manuscript database

This bulletin is largely based on research conducted at the University of Idaho during 2000-2009. Corkbark and subalpine fir have desirable characteristics for Christmas tree and landscape use, including soft, fragrant foliage that ranges from dark green to silvery or bluish-green. Depending on seed...

Evolutionary history of two endemic Appalachian conifers revealed using microsatellite markers

Treesearch

Kevin M. Potter; John Frampton; Sedley A. Josserand; C. Dana Nelson

2010-01-01

Fraser fir (Abies fraseri [Pursh] Poir.) and intermediate fir (Abies balsamea [L.] Mill. var. phanerolepis Fern.) exist in small populations in the Appalachian highlands of the southeastern United States. We used ten nuclear microsatellite markers to quantify genetic variation within Fraser fir and intermediate...

Adapted all-numerical correlator for face recognition applications

NASA Astrophysics Data System (ADS)

Elbouz, M.; Bouzidi, F.; Alfalou, A.; Brosseau, C.; Leonard, I.; Benkelfat, B.-E.

2013-03-01

In this study, we suggest and validate an all-numerical implementation of a VanderLugt correlator which is optimized for face recognition applications. The main goal of this implementation is to take advantage of the benefits (detection, localization, and identification of a target object within a scene) of correlation methods and exploit the reconfigurability of numerical approaches. This technique requires a numerical implementation of the optical Fourier transform. We pay special attention to adapt the correlation filter to this numerical implementation. One main goal of this work is to reduce the size of the filter in order to decrease the memory space required for real time applications. To fulfil this requirement, we code the reference images with 8 bits and study the effect of this coding on the performances of several composite filters (phase-only filter, binary phase-only filter). The saturation effect has for effect to decrease the performances of the correlator for making a decision when filters contain up to nine references. Further, an optimization is proposed based for an optimized segmented composite filter. Based on this approach, we present tests with different faces demonstrating that the above mentioned saturation effect is significantly reduced while minimizing the size of the learning data base.

Technical and social evaluation of arsenic mitigation in rural Bangladesh.

PubMed

Shafiquzzaman, Md; Azam, Md Shafiul; Mishima, Iori; Nakajima, Jun

2009-10-01

Technical and social performances of an arsenic-removal technology--the sono arsenic filter--in rural areas of Bangladesh were investigated. Results of arsenic field-test showed that filtered water met the Bangladesh standard (< 50 microg/L) after two years of continuous use. A questionnaire was administrated among 198 sono arsenic filter-user and 230 non-user families. Seventy-two percent of filters (n = 198) were working at the time of the survey. Another 28% of the filters were abandoned due to breakage. The abandonment percentage (28%) was lower than other mitigation options currently implemented in Bangladesh. Households were reluctant to repair the broken filters on their own. High cost, problems with maintenance of filters, weak sludge-disposal guidance, and slow flow rate were the other demerits of the filter. These results indicate that the implementation approaches of the sono arsenic filter suffered from lack of ownership and long-term sustainability. Continuous use of arsenic-contaminated tubewells by the non-user households demonstrated the lack of alternative water supply in the survey area. Willingness of households to pay (about 30%) and preference of household filter (50%) suggest the need to develop a low-cost household arsenic filter. Development of community-based organization would be also necessary to implement a long-term, sustainable plan for household-based technology.

77 FR 2930 - Airworthiness Directives; Turbomeca S.A. Turboshaft Engines

Federal Register 2010, 2011, 2012, 2013, 2014

2012-01-20

... certain power turbine (PT) blade fir-tree roots. This proposed AD would require removing the affected PT... detected geometric non-conformities on blade fir-tree roots. The technical investigations carried out by... was prompted by the detection of geometric non- conformities on PT blade fir-tree roots. We are...

Dwarf Mistletoe on Red Fir . . . infection and control in understory stands

Treesearch

Robert F. Scharpf

1969-01-01

Height and age of understory red fir (Abies magnifica A. Murr.) were related to dwarf mistletoe (Arceuthobiilm campylopodum f. abietinum) infection from the surrounding overstory red fir on four National Forests in California. Percentage of trees infected and intensity of infection increased significantly as height of understory...

Fraser fir stand structure in the Black Mountains of North Carolina

Treesearch

Rachael H. McManamay; Lynn M. Resle; James B. Campbell

2010-01-01

Over the past several decades, naturally occurring populations of Fraser fir (Abies fraseri [Pursh.] Poir) have experienced devastating mortality rates due to attack by the exotic insect, balsam woolly adelgid (BWA) (Adelges piceae Ratz.). The decline in Fraser fir is particularly concerning because its natural geographic...

Belowground competition from overstory trees influences Douglas-fir sapling morphology in thinned stands

Treesearch

Warren D. Devine; Timothy B. Harrington

2009-01-01

We evaluated effects of belowground competition on morphology of naturally established coast Douglas-fir (Pseudotsuga menziesii var. menziesii (Mirb.) Franco) saplings in 60- to 80-year-old thinned Douglas-fir stands in southwestern Washington. We separately quantified belowground competition from overstory and understory sources...

AmeriFlux CA-Cha New Brunswick - Charlie Lake site 01 (immature balsam fir forest to be thinned in year 3)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bourque, Charles

This is the AmeriFlux version of the carbon flux data for the site CA-Cha New Brunswick - Charlie Lake site 01 (immature balsam fir forest to be thinned in year 3). Site Description - mature balsam fir forest

Jet Drying of Southern Pine and Douglas-Fir: Exploratory Study

Treesearch

Howard N. Rosen

1978-01-01

Southern pine and Douglas-fir boards, containing both heart- and sapwood and 1.75 inches thick, were jet dried at temperatures from 160 to 400 F and air velocities from 3,000 to 9,000 fmp. Jet drying was more effective for southern pine than for Douglas-fir.

A forest health inventory assessment of red fir (Abies magnifica) in upper montane California

Treesearch

Leif Mortenson; Andrew N. Gray; David C. Shaw

2015-01-01

We investigated the forest health of red fir (Abies magnifica) and how it compared with commonly-associated species Jeffrey pine (Pinus jeffreyi), lodgepole pine (Pinus contorta) and white fir (Abies concolor) in the upper montane forests of California. We evaluated tree mortality rates...

Response of different white fir geographic provenances to Trichosporium symbioticum inoculation in California

Treesearch

William J. Otrosina; Stanley J. Zarnoch

2012-01-01

We inoculated the fir engraver (Scolytus ventralis LeConte) associated fungus Trichosporium symbioticum Wright onto 56 white fir (Abies concolor (Gordon & Glend.) Lindl. ex Hildebr.) trees planted in a common garden study near Camino, California, that represented five geographic provenances of this species....

Saddle Bag Mountain Research Natural Area: guidebook supplement 34.

Treesearch

Reid Schuller; Ronald L. Exeter

2007-01-01

This guidebook describes the Saddle Bag Mountain Research Natural Area, a 121-ha (300-ac) tract established to represent an old-growth remnant of Pacific silver fir (Abies amabilis) and western hemlock (Tsuga heterophylla) forest in the Oregon Coast Range. Pacific silver fir and noble fir (Abies procera)...

Madrone duff and the natural regeneration of Douglas-fir.

Treesearch

Don Minore

1987-01-01

Excellent natural regeneration of Douglas-fir (Pseudotsuga menziesii [Mirb.] Franco) often occurs under canopies of Pacific madrone (Arbutus menziesii Pursh), but the effects of madrone duff on regeneration are poorly understood. A field experiment was conducted in a thinned Douglas-fir stand in southwestern Oregon to see if...

Dwarfmistletoe of Douglas-fir

Treesearch

Donald P. Graham

1961-01-01

Dwarfmistletoe (Arceuthobium douglasii Engelm.), one of the most destructive enemies of Douglas-fir, causes serious losses in many stands. This parasitic plant is present almost everywhere within the range of Douglas-fir in the northern, central, and southern Rockies. It is abundant in eastern Washington and Oregon and is common in southwestern Oregon and northern...

Truffle abundance and mycophagy by northern flying squirrels in eastern Washington forests.

Treesearch

John F. Lehmkuhl; Laura E. Gould; Efren Cazares; David R. Hosford

2004-01-01

Although much is known about truffle abundance and rodent mycophagy in mesic Douglas-fir forests in the Pacific Northwest, few data are available for dry interior montane forests dominated by ponderosa pine (Pinus ponderosa), Douglas-fir (Pseudotsuga menziesii), and grand fir (Abies grandis). Our objective...

Douglas-fir displays a range of growth responses to temperature, water, and Swiss needle cast in western Oregon, USA

EPA Science Inventory

Douglas-fir (Pseudotsuga menziesii var. menziesii (Mirb.) Franco) growth in the Pacific Northwest is affected by climatic, edaphic factors and Swiss needle cast (SNC) disease. We examine Douglas-fir growth responses to temperature, dewpoint deficit (DPD), soil moisture, and SNC ...

Graft union formation in Douglas-fir.

Treesearch

D.L. Copes

1969-01-01

Greenhouse-grown Douglas-fir (Pseudotsuga menziesii [Mirb.] Franco) graft unions were examined between 2 and 84 days after grafting. Room temperature was maintained at 60-70 F throughout the growing season. In most respects grafts of Douglas-fir followed development patterns previously reported for spruce and pine grafts, but specific differences...

Design and analysis of optically pumped submillimeter waveguide maser amplifiers and oscillators

NASA Technical Reports Server (NTRS)

Galantowicz, T. A.

1975-01-01

The design and experimental measurements are described of an optically pumped far-infrared (FIR) waveguide maser; preliminary measurements on a FIR waveguide amplifier are presented. The FIR maser was found to operate satisfactorily in a chopped CW mode using either methanol (CH3OH) or acetonitrile (CH3CN) as the active molecule. Two other gases, difluoroethane and difluoroethylene, produced an unstable output with high threshold and low output power when operated in the chopped CW mode. Experimental measurements include FIR output versus cavity length, output beam pattern, output power versus pressure, and input power. The FIR output was the input to an amplifier which was constructed similar to the oscillator. An increase of 10% in output power was noted on the 118.8 microns line of methanol.

Simulations of a FIR Oscillator with Large Slippage parameter at Jefferson Lab for FIR/UV pump-probe experiments

DOE Office of Scientific and Technical Information (OSTI.GOV)

Benson, Stephen V.; Campbell, L. T.; McNeil, B.W.T.

We previously proposed a dual FEL configuration on the UV Demo FEL at Jefferson Lab that would allow simultaneous lasing at FIR and UV wavelengths. The FIR source would be an FEL oscillator with a short wiggler providing diffraction-limited pulses with pulse energy exceeding 50 microJoules, using the exhaust beam from a UVFEL as the input electron beam. Since the UV FEL requires very short pulses, the input to the FIR FEL is extremely short compared to a slippage length and the usual Slowly Varying Envelope Approximation (SVEA) does not apply. We use a non-SVEA code to simulate this systemmore » both with a small energy spread (UV laser off) and with large energy spread (UV laser on).« less

The Dust Content and Opacity of Actively Star-Forming Galaxies

NASA Technical Reports Server (NTRS)

Calzetti, Daniela; Armus, Lee; Bohlin, Ralph C.; Kinney, Anne L.; Koornneef, Jan; Storchi-Bergmann, Thaisa

2000-01-01

We present far-infrared (FIR) photometry at 150 and 205 micron(s) of eight low-redshift starburst galaxies obtained with the Infrared Space Observatory (ISO) ISOPHOT. Five of the eight galaxies are detected in both wave bands, and these data are used, in conjunction with IRAS archival photometry, to model the dust emission at lambda approximately greater than 40 microns. The FIR spectral energy distributions (SEDs) are best fitted by a combination of two modified Planck functions, with T approx. 40 - 55 K (warm dust) and T approx. 20-23 K (cool dust) and with a dust emissivity index epsilon = 2. The cool dust can be a major contributor to the FIR emission of starburst galaxies, representing up to 60% of the total flux. This component is heated not only by the general interstellar radiation field, but also by the starburst itself. The cool dust mass is up to approx. 150 times larger than the warm dust mass, bringing the gas-to-dust ratios of the starbursts in our sample close to Milky Way values, once resealed for the appropriate metallicity. The ratio between the total dust FIR emission in the range 1-1000 microns and the IRAS FIR emission in the range 40 - 120 microns is approx. 1.75, with small variations from galaxy to galaxy. This ratio is about 40% larger than previously inferred from data at millimeter wavelengths. Although the galaxies in our sample are generally classified as "UV bright," for four of them the UV energy emerging shortward of 0.2 microns is less than 15% of the FIR energy. On average, about 30% of the bolometric flux is coming out in the UV-to-near-IR wavelength range; the rest is emitted in the FIR. Energy balance calculations show that the FIR emission predicted by the dust reddening of the UV-to-near-IR stellar emission is within a factor of approx. 2 of the observed value in individual galaxies and within 20% when averaged over a large sample. If our sample of local starbursts is representative of high-redshift (z approx. greater than 1), UV - bright star-forming galaxies, these galaxies' FIR emission will be generally undetected in submillimeter surveys, unless: (1) their bolometric luminosity is comparable to or larger than that of ultraluminous FIR galaxies and (2) their FIR SED contains a cool dust component.

The Seismic Tool-Kit (STK): an open source software for seismology and signal processing.

NASA Astrophysics Data System (ADS)

Reymond, Dominique

2016-04-01

We present an open source software project (GNU public license), named STK: Seismic ToolKit, that is dedicated mainly for seismology and signal processing. The STK project that started in 2007, is hosted by SourceForge.net, and count more than 19 500 downloads at the date of writing. The STK project is composed of two main branches: First, a graphical interface dedicated to signal processing (in the SAC format (SAC_ASCII and SAC_BIN): where the signal can be plotted, zoomed, filtered, integrated, derivated, ... etc. (a large variety of IFR and FIR filter is proposed). The estimation of spectral density of the signal are performed via the Fourier transform, with visualization of the Power Spectral Density (PSD) in linear or log scale, and also the evolutive time-frequency representation (or sonagram). The 3-components signals can be also processed for estimating their polarization properties, either for a given window, or either for evolutive windows along the time. This polarization analysis is useful for extracting the polarized noises, differentiating P waves, Rayleigh waves, Love waves, ... etc. Secondly, a panel of Utilities-Program are proposed for working in a terminal mode, with basic programs for computing azimuth and distance in spherical geometry, inter/auto-correlation, spectral density, time-frequency for an entire directory of signals, focal planes, and main components axis, radiation pattern of P waves, Polarization analysis of different waves (including noize), under/over-sampling the signals, cubic-spline smoothing, and linear/non linear regression analysis of data set. A MINimum library of Linear AlGebra (MIN-LINAG) is also provided for computing the main matrix process like: QR/QL decomposition, Cholesky solve of linear system, finding eigen value/eigen vectors, QR-solve/Eigen-solve of linear equations systems ... etc. STK is developed in C/C++, mainly under Linux OS, and it has been also partially implemented under MS-Windows. Usefull links: http://sourceforge.net/projects/seismic-toolkit/ http://sourceforge.net/p/seismic-toolkit/wiki/browse_pages/

Ectomycorrhizal fungi associated with ponderosa pine and Douglas-fir: a comparison of species richness in native western North American forests and Patagonian plantations from Argentina.

PubMed

Barroetaveña, C; Cázares, E; Rajchenberg, M

2007-07-01

The putative ectomycorrhizal fungal species registered from sporocarps associated with ponderosa pine and Douglas-fir forests in their natural range distribution (i.e., western Canada, USA, and Mexico) and from plantations in south Argentina and other parts of the world are listed. One hundred and fifty seven taxa are reported for native ponderosa pine forests and 514 taxa for native Douglas-fir forests based on available literature and databases. A small group of genera comprises a high proportion of the species richness for native Douglas-fir (i.e., Cortinarius, Inocybe, and Russula), whereas in native ponderosa pine, the species richness is more evenly distributed among several genera. The comparison between ectomycorrhizal species richness associated with both trees in native forests and in Patagonia (Argentina) shows far fewer species in the latter, with 18 taxa for the ponderosa pine and 15 for the Douglas-fir. Epigeous species richness is clearly dominant in native Douglas-fir, whereas a more balanced relation epigeous/hypogeous richness is observed for native ponderosa pine; a similar trend was observed for Patagonian plantations. Most fungi in Patagonian Douglas-fir plantations have not been recorded in plantations elsewhere, except Suillus lakei and Thelephora terrestris, and only 56% of the fungal taxa recorded in Douglas-fir plantations around the world are known from native forests, the other taxa being new associations for this host, suggesting that new tree + ectomycorrhizal fungal taxa associations are favored in artificial situations as plantations.

Fir Decline and Mortality in the Southern Siberian Mountains

NASA Technical Reports Server (NTRS)

Kharuk, Viacheslav I.; Im, Sergei T.; Petrov, Ilya A.; Dvinskaya, Mariya, L.; Fedotova, Elena V.; Ranson, Kenneth J.

2016-01-01

Increased dieback and mortality of dark needle conifer (DNC) stands (composed of fir (Abies sibirica),Siberian pine (Pinus sibirica) and spruce (Picea obovata)) were documented in Russia during recent decades. Here we analyzed spatial and temporal patterns of fir decline and mortality in the southern Siberian Mountains based on satellite, in situ and dendrochronological data. The studied stands are located within the boundary between DNC taiga to the north and forest-steppe to the south. Fir decline and mortality were observed to originate where topographic features contributed to maximal water-stress risk, i.e., steep (18 deg to 25 deg), convex, south-facing slopes with a shallow well-drained root zone. Fir regeneration survived droughts and increased stem radial growth, while upper canopy trees died. Tree ring width (TRW) growth negatively correlated with vapor pressure deficit (VPD), drought index and occurrence of late frosts, and positively with soil water content. Previous year growth conditions (i.e., drought index, VPD, soil water anomalies) have a high impact on current TRW (r = 0.60 to 0.74). Fir mortality was induced by increased water stress and severe droughts (as a primary factor) in synergy with bark-beetles and fungi attacks (as secondary factors). Dendrochronology data indicated that fir mortality is a periodic process. In a future climate with increased aridity and drought frequency, fir (and Siberian pine) may disappear from portions of its current range (primarily within the boundary with the forest- steppe) and is likely to be replaced by drought-tolerant species such as Pinus sylvestris and Larix sibirica.

RADIO OBSERVATIONS OF THE STAR FORMATION ACTIVITIES IN THE NGC 2024 FIR 4 REGION

DOE Office of Scientific and Technical Information (OSTI.GOV)

Choi, Minho; Kang, Miju; Lee, Jeong-Eun, E-mail: minho@kasi.re.kr

Star formation activities in the NGC 2024 FIR 4 region were studied by imaging centimeter continuum sources and water maser sources using several archival data sets from the Very Large Array. The continuum source VLA 9 is elongated in the northwest–southeast direction, consistent with the FIR 4 bipolar outflow axis, and has a flat spectrum in the 6.2–3.6 cm interval. The three water maser spots associated with FIR 4 are also distributed along the outflow axis. One of the spots is located close to VLA 9, and another one is close to an X-ray source. Examinations of the positions ofmore » compact objects in this region suggest that the FIR 4 cloud core contains a single low-mass protostar. VLA 9 is the best indicator of the protostellar position. VLA 9 may be a radio thermal jet driven by this protostar, and it is unlikely that FIR 4 contains a high-mass young stellar object (YSO). A methanol 6.7 GHz maser source is located close to VLA 9, at a distance of about 100 AU. The FIR 4 protostar must be responsible for the methanol maser action, which suggests that methanol class II masers are not necessarily excited by high-mass YSOs. Also discussed are properties of other centimeter continuum sources in the field of view and the water masers associated with FIR 6n. Some of the continuum sources are radio thermal jets, and some are magnetically active young stars.« less

Survey for balsam woolly adegid in Washington and Oregon.

Treesearch

I. Ragenovich; B. Willhite; R. Mitchell; D. Overhulser; K. Ripley

2002-01-01

Balsam woolly adelgid (BWA) is an introduced insect that has had a significant impact on Abies tree species in the Pacific Northwest. During the late 1950s and 1960s, it caused extensive mortality of grand fir (A. grandis), subalpine fir (A. lasiocarpa), and silver fir (A. amabilis), particularly in the...

Relationship between self-fertility, allocation of growth, and inbreeding depression in three coniferous species.

Treesearch

Frank C. Sorensen

1999-01-01

Mortality and growth of self and outcross families of three wind-pollinated, mixed-mating, long-lived conifers, Douglas-fir (Pseudotsuga menziesii), ponderosa pine (Pinus ponderosa), and noble fir (Abies procera) were followed from outplanting to age 26 (25 for noble fir) in spaced plantings at a common...

Pulp quality from small-diameter trees.

Treesearch

G.C. Myers; S. Kumar; R.R. Gustafson; R.J. Barbour; S.M. Abubakr

1997-01-01

Kraft and thermomechanical (TMP) pulps were prepared and evaluated from lodgepole pine and mixed Douglas-fir/western larch sawmill residue chips; lodgepole pine, Douglas-fir, and western larch submerchantable logs; and lodgepole pine, Douglas-fir, and western larch small trees and tops. Kraft pulp from small trees and tops was identical to that from submerchantable...

Population dynamics of dwarf mistletoe on young true firs in the central Sierra Nevada, California

Treesearch

Robert E Scharpf; J. R. Jr. Parmeter

1982-01-01

Young red firs (Abies magnifica A. Murr.) and white firs (A. concolor [Gord. & Glend.] Lindl. ex Hildebr.) on the Stanislaus National Forest, California, were inoculated with seeds of dwarf mistletoe (Arceuthobium abietinum) for 5 successive years. Only 3 to 4 percent of about 7000 seeds placed on branches...

Growth of bear-damaged trees in a mixed plantation of Douglas-fir and red alder.

Treesearch

Richard E. Miller; Harry W. Anderson; Donald L. Reukema; Timothy A. Max

2007-01-01

Incidence and effects of tree damage by black bear (Ursus americanus altifrontalis) in a 50-year-old, coast Douglas-fir (Pseudotsuga menziesii (Mirb.) Franco var. menziesii) plantation are described. Bears girdled or partially girdled 35 dominant or codominant Douglas-fir trees per acre, but only in that...

Forest tree improvement in California-1970

Treesearch

M. Thompson Conkle

1972-01-01

Foresters in California were surveyed in 1970 to determine the extent of artificial regeneration and tree improvement efforts in the State. Seeding of Douglas-fir was the prevailing practice in the North Coast. Inland areas were being planted with conifers, including ponderosa, Jeffrey, Monterey, and sugar pines, Douglas-fir, and red and white firs. Manpower devoted to...

Conversion of SPORL pretreated Douglas fir forest residues into microbial lipids with oleaginous yeasts

USDA-ARS?s Scientific Manuscript database

Douglas fir is the dominant commercial tree grown in the United States. In this study Douglas fir residue was converted to single cell oils using oleaginous yeasts. Monosaccharides were extracted from the woody biomass by pretreating with sulfite and dilute sulfuric acid (SPORL process) and hydrol...

A SNP resource for douglas-fir: de novo transcriptome assembly and SNP detection and validation

Treesearch

Glenn R. Howe; Jianbin Yu; Brian Knaus; Richard Cronn; Scott Kolpak; Peter Dolan; W. Walter Lorenz; Jeffrey F.D. Dean

2013-01-01

Douglas-fir (Pseudotsuga menziesii), one of the most economically and ecologically important tree species in the world, also has one of the largest tree breeding programs. Although the coastal and interior varieties of Douglas-fir (vars. menziesii and glauco) are native to North America, the coastal variety is...

First report of Phytophthora ramorum infecting grand fir in California

Treesearch

K.L. Riley; G.A. Chastagner

2011-01-01

Phytophthora ramorum was detected on grand fir in 2003 and 2005 in a Christmas tree plantation near Los Gatos, CA, in association with infected California bay laurel. Isolates derived from stem lesions were used to inoculate grand fir seedlings in two tests. Isolations from lesions on inoculated plants were positive for P. ramorum...

Climate and growth rate as related to an outbreak of silver fir beetles.

Treesearch

Gerard M. Thomas

1957-01-01

In 1947, an outbreak of silver fir beetles, Pseudohylesinus grandis Sw. and P. granulatus (Lec.), was discovered in northwestern Washington. The epidemic flourished for the next six years, killing some 525 million board-feet of Pacific silver fir, Abies amabilis (Dougl.) Forbes. Prior to 1947, the silver...

Shelterwood regeneration of true fir: conclusion after 8 years

Treesearch

Robert J. Laacke; Jeanne H. Tomascheski

1986-01-01

Shelterwood cuttings on Swain Mountain Experimental Forest were measured to determine performance six to eight years after the shelterwood cutting and before shelterwood removal. Use of appropriate selecting criteria minimized windthrow of seed trees. Regeneration remained red fir, even where the major seed source was white fir. Density of seed trees may affect...

Photo guide for appraising downed woody fuels in Montana forests: Interior ponderosa pine, ponderosa pine - larch - Douglas-fir, larch - Douglas-fir, and interior Douglas-fir cover types

Treesearch

William C. Fischer

1981-01-01

Four series of color photographs show different levels of downed woody material resulting from natural processes in four forest cover types in Montana. Each photo is supplemented by fuel inventory data and potential fire behavior ratings.

Douglas-fir tussock moth: an annotated bibliography.

Treesearch

Robert W. Campbell; Lorna C. Youngs

1978-01-01

This annotated bibliography includes references to 338 papers. Each deals in some way with either the Douglas-fir tussock moth, Orgyia pseudotsugata (McDunnough), or a related species. Specifically, 210 publications and 82 unpublished documents make some reference, at least, to the Douglas-fir tussock moth; 55 are concerned with other species in...

Survival, frost susceptibility, growth, and disease resistance of corkbark and subalpine fir grown for landscape and Christmas trees

USDA-ARS?s Scientific Manuscript database

Trees from six corkbark fir (Abies lasiocarpa var. arizonica) and 10 subalpine fir (A. lasiocarpa var. lasiocarpa) seed sources were grown at the University of Idaho Sandpoint Research and Extension Center (SREC) and two commercial nurseries in Idaho and Oregon. Post transplant mortality was highest...

Multi-decadal establishment for single-cohort Douglas-fir forests

Treesearch

James A. Freund; Jerry F. Franklin; Andrew J. Larson; James A. Lutz

2014-01-01

The rate at which trees regenerate following stand-replacing wildfire is an important but poorly understood process in the multi-century development of Douglas-fir (Pseudotsuga menziesii (Mirb.) Franco) and western hemlock (Tsuga heterophylla (Raf.) Sarg.) forests. Temporal patterns of Douglas-fir establishment reconstructed from old-growth forests (>450 year) have...

Mammoth lakes revisited—50 years after a Douglas-fir tussock moth outbreak.

Treesearch

Boyd E. Wickman; G. Lynn Starr

1990-01-01

For five decades after an outbreak of Douglas-fir tussock moth (Orgyia pseudotsugata (McDunnough)), radial growth of defoliated white fir trees (Abies concolor (Gord. & Glend.) Lindl.), was significantly greater than that of nondefoliated host trees nearby. The increased growth probably was due to the thinning effect of...

An audit of manufacturers' implementation of reconstruction filters in single-photon emission computed tomography.

PubMed

Lawson, Richard S; White, Duncan; Cade, Sarah C; Hall, David O; Kenny, Bob; Knight, Andy; Livieratos, Lefteris; Nijran, Kuldip

2013-08-01

The Nuclear Medicine Software Quality Group of the Institute of Physics and Engineering in Medicine has conducted an audit to compare the ways in which different manufacturers implement the filters used in single-photon emission computed tomography. The aim of the audit was to identify differences between manufacturers' implementations of the same filter and to find means for converting parameters between systems. Computer-generated data representing projection images of an ideal test object were processed using seven different commercial nuclear medicine systems. Images were reconstructed using filtered back projection and a Butter worth filter with three different cutoff frequencies and three different orders. The audit found large variations between the frequency-response curves of what were ostensibly the same filters on different systems. The differences were greater than could be explained simply by different Butter worth formulae. Measured cutoff frequencies varied between 40 and 180% of that expected. There was also occasional confusion with respect to frequency units. The audit concluded that the practical implementation of filtering, such as the size of the kernel, has a profound effect on the results, producing large differences between systems. Nevertheless, this work shows how users can quantify the frequency response of their own systems so that it will be possible to compare two systems in order to find filter parameters on each that produce equivalent results. These findings will also make it easier for users to replicate filters similar to other published results, even if they are using a different computer system.

Analysis of conifer forest regeneration using Landsat Thematic Mapper data

NASA Technical Reports Server (NTRS)

Fiorella, Maria; Ripple, William J.

1995-01-01

Landsat Thematic Mapper (TM) data were used to evaluate young conifer stands in the western Cascade Mountains of Oregon. Regression and correlation analyses were used to describe the relationships between TM band values and age of young Douglas-fir stands (2 to 35 years old). Spectral data from well regenerated Douglas-fir stands were compared to those of poorly regenerated conifer stands. TM bands 1, 2, 3, 5, 6, and 7 were inversely correlated with the age (r greater than or equal to -0.80) of well regenerated Douglas-fir stands. Overall, the 'structural index' (TM 4/5 ratio) had the highest correlation to age of Douglas-fir stands (r = 0.96). Poorly regenerated stands were spectrally distinct from well regenerated Douglas-fir stands after the stands reached an age of approximately 15 years.

Accurate thermometry based on the red and green fluorescence intensity ratio in NaYF₄: Yb, Er nanocrystals for bioapplication.

PubMed

Liu, Lixin; Qin, Feng; Lv, Tianquan; Zhang, Zhiguo; Cao, Wenwu

2016-10-15

A biological temperature measurement method based on the fluorescence intensity ratio (FIR) was developed to reduce uncertainty. The upconversion luminescence of NaYF₄:Yb, Er nanocrystals was studied as a function of temperature around the physiologically relevant range of 300-330 K. We found that the green-green FIR Fe and red-green FIR (I₆₆₀/I₅₄₀) varied linearly as temperature increased. The thermometric uncertainties using the two FIRs were discussed and were determined to be almost constant at 0.6 and 0.09 K for green-green and red-green, respectively. The lower thermometric uncertainty comes from the intense signal-to-noise ratio of the measured FIRs owing to their comparable fluorescence intensities.

VizieR Online Data Catalog: PACS photometry of FIR faint stars (Klaas+, 2018)

NASA Astrophysics Data System (ADS)

Klaas, U.; Balog, Z.; Nielbock, M.; Mueller, T. G.; Linz, H.; Kiss, Cs.

2018-01-01

70, 100 and 160um photometry of FIR faint stars from PACS scan map and chop/nod measurements. For scan maps also the photometry of the combined scan and cross-scan maps (at 160um there are usually two scan and cross-scan maps each as complements to the 70 and 100um maps) is given. Note: Not all stars have measured fluxes in all three filters. Scan maps: The main observing mode was the point-source mini-scan-map mode; selected scan map parameters are given in column mparam. An outline of the data processing using the high-pass filter (HPF) method is presented in Balog et al. (2014ExA....37..129B). Processing proceeded from Herschel Science Archive SPG v13.1.0 level 1 products with HIPE version 15 build 165 for 70 and 100um maps and from Herschel Science Archive SPG v14.2.0 level 1 products with HIPE version 15 build 1480 for 160um maps. Fluxes faper were obtained by aperture photometry with aperture radii of 5.6, 6.8 and 10.7 arcsec for the 70, 100 and 160um filter, respectively. Noise per pixel sigpix was determined with the histogram method, described in this paper, for coverage values greater than or equal to 0.5*maximum coverage. The number of map pixels (1.1, 1.4, and 2.1 arcsec pixel size, respectively) inside the photometric aperture is Naper = 81.42, 74.12, and 81.56, respectively. The corresponding correction factors for correlated noise are fcorr = 3.13, 2.76, and 4.12, respectively. The noise for the photometric aperture is calculated as sig_aper=sqrt(Naper)*fcorr*sigpix. Signal-to-noise ratios are determined as S/N=faper/sigaper. Aperture-correction factors to derive the total flux are caper = 1.61, 1.56 and 1.56 for the 70, 100 and 160um filter, respectively. Applied colour-correction factors for a 5000K black-body SED are cc = 1.016, 1.033, and 1.074 for the 70, 100, and 160um filter, respectively. The final stellar flux is derived as fstar=faper*caper/cc. Maximum and minimum FWHM of the star PSF are determined by an elliptical fit of the intensity profile. Chop/nod observations: The chop/nod point-source mode is described in this paper. An outline of the data processing is presented in Nielbock et al. (2013ExA....36..631N). Processing proceeded from Herschel Science Archive SPG v11.1.0 level 1 products with HIPE version 13 build 2768. Gyro correction was applied for most of the cases to improve the pointing reconstruction performance. Fluxes faper were obtained by aperture photometry with aperture radii of 5.6, 6.8 and 10.7 arcsec for the 70, 100 and 160um filter, respectively. Noise per pixel sigpix was determined with the histogram method, described in this paper, for coverage values greater than or equal to 0.5*maximum coverage. The number of map pixels (1.1, 1.4, and 2.1 arcsec pixel size, respectively) inside the photometric aperture is Naper = 81.42, 74.12, and 81.56, respectively. The corresponding correction factors for correlated noise are fcorr = 6.33, 4.22, and 7.81, respectively. The noise for the photometric aperture is calculated as sigaper=sqrt(Naper)*fcorr*sigpix. Signal-to-noise ratios are determined as S/N=faper/sigaper. Aperture-correction factors to derive the total flux are caper = 1.61, 1.56 and 1.56 for the 70, 100 and 160um filter, respectively. Applied colour-correction factors for a 5000K black-body SED are cc = 1.016, 1.033, and 1.074 for the 70, 100, and 160um filter, respectively. Maximum and minimum FWHM of the star PSF are determined by an elliptical fit of the intensity profile. (7 data files).

Improving Real World Performance of Vision Aided Navigation in a Flight Environment

DTIC Science & Technology

2016-09-15

Introduction . . . . . . . 63 4.2 Wide Area Search Extent . . . . . . . . . . . . . . . . . 64 4.3 Large-Scale Image Navigation Histogram Filter ...65 4.3.1 Location Model . . . . . . . . . . . . . . . . . . 66 4.3.2 Measurement Model . . . . . . . . . . . . . . . 66 4.3.3 Histogram Filter ...Iteration of Histogram Filter . . . . . . . . . . . 70 4.4 Implementation and Flight Test Campaign . . . . . . . . 71 4.4.1 Software Implementation

Herschel/PACS far-IR spectral imaging of a jet from an intermediate mass protostar in the OMC-2 region

NASA Astrophysics Data System (ADS)

González-García, B.; Manoj, P.; Watson, D. M.; Vavrek, R.; Megeath, S. T.; Stutz, A. M.; Osorio, M.; Wyrowski, F.; Fischer, W.; Tobin, J. J.; Sánchez-Portal, M.; Diaz Rodriguez, A. K.; Wilson, T. L.

2016-11-01

We present the first detection of a jet in the far-IR [O I] lines from an intermediate mass protostar. This jet was detected in a Herschel/PACS spectral mapping study in the [O I] lines of OMC-2 FIR 3 and FIR 4, two of the most luminous protostars in Orion outside of the Orion Nebula. The spatial morphology of the fine structure line emission reveals the presence of an extended photodissociation region (PDR) and a narrow, but intense jet connecting the two protostars. The jet seen in [O I] emission is spatially aligned with the Spitzer/IRAC 4.5 μm jet and the CO (6-5) molecular outflow centered on FIR 3. The mass-loss rate derived from the total [O I] 63 μm line luminosity of the jet is 7.7 × 10-6M⊙ yr-1, more than an order of magnitude higher than that measured for typical low-mass class 0 protostars. The implied accretion luminosity is significantly higher than the observed bolometric luminosity of FIR 4, indicating that the [O I] jet is unlikely to be associated with FIR 4. We argue that the peak line emission seen toward FIR 4 originates in the terminal shock produced by the jet driven by FIR 3. The higher mass-loss rate that we find for FIR 3 is consistent with the idea that intermediate-mass protostars drive more powerful jets than their low-mass counterparts. Our results also call into question the nature of FIR 4. Herschel is an ESA space observatory with science instruments provided by European-led Principal Investigator consortia and with important participation from NASA.The final reduced Herschel data used in this paper (FITS) are only available at the CDS via anonymous ftp to http://cdsarc.u-strasbg.fr (http://130.79.128.5) or via http://cdsarc.u-strasbg.fr/viz-bin/qcat?J/A+A/596/A26

Space-time adaptive decision feedback neural receivers with data selection for high-data-rate users in DS-CDMA systems.

PubMed

de Lamare, Rodrigo C; Sampaio-Neto, Raimundo

2008-11-01

A space-time adaptive decision feedback (DF) receiver using recurrent neural networks (RNNs) is proposed for joint equalization and interference suppression in direct-sequence code-division multiple-access (DS-CDMA) systems equipped with antenna arrays. The proposed receiver structure employs dynamically driven RNNs in the feedforward section for equalization and multiaccess interference (MAI) suppression and a finite impulse response (FIR) linear filter in the feedback section for performing interference cancellation. A data selective gradient algorithm, based upon the set-membership (SM) design framework, is proposed for the estimation of the coefficients of RNN structures and is applied to the estimation of the parameters of the proposed neural receiver structure. Simulation results show that the proposed techniques achieve significant performance gains over existing schemes.

Optical systolic solutions of linear algebraic equations

NASA Technical Reports Server (NTRS)

Neuman, C. P.; Casasent, D.

1984-01-01

The philosophy and data encoding possible in systolic array optical processor (SAOP) were reviewed. The multitude of linear algebraic operations achievable on this architecture is examined. These operations include such linear algebraic algorithms as: matrix-decomposition, direct and indirect solutions, implicit and explicit methods for partial differential equations, eigenvalue and eigenvector calculations, and singular value decomposition. This architecture can be utilized to realize general techniques for solving matrix linear and nonlinear algebraic equations, least mean square error solutions, FIR filters, and nested-loop algorithms for control engineering applications. The data flow and pipelining of operations, design of parallel algorithms and flexible architectures, application of these architectures to computationally intensive physical problems, error source modeling of optical processors, and matching of the computational needs of practical engineering problems to the capabilities of optical processors are emphasized.

Herschel-PACS photometry of faint stars for sensitivity performance assessment and establishment of faint FIR primary photometric standards

NASA Astrophysics Data System (ADS)

Klaas, U.; Balog, Z.; Nielbock, M.; Müller, T. G.; Linz, H.; Kiss, Cs.

2018-05-01

Aims: Our aims are to determine flux densities and their photometric accuracy for a set of seventeen stars that range in flux from intermediately bright (≲2.5 Jy) to faint (≳5 mJy) in the far-infrared (FIR). We also aim to derive signal-to-noise dependence with flux and time, and compare the results with predictions from the Herschel exposure-time calculation tool. Methods: We obtain aperture photometry from Herschel-PACS high-pass-filtered scan maps and chop/nod observations of the faint stars. The issues of detection limits and sky confusion noise are addressed by comparison of the field-of-view at different wavelengths, by multi-aperture photometry, by special processing of the maps to preserve extended emission, and with the help of large-scale absolute sky brightness maps from AKARI. This photometry is compared with flux-density predictions based on photospheric models for these stars. We obtain a robust noise estimate by fitting the flux distribution per map pixel histogram for the area around the stars, scaling it for the applied aperture size and correcting for noise correlation. Results: For 15 stars we obtain reliable photometry in at least one PACS filter, and for 11 stars we achieve this in all three PACS filters (70, 100, 160 μm). Faintest fluxes, for which the photometry still has good quality, are about 10-20 mJy with scan map photometry. The photometry of seven stars is consistent with models or flux predictions for pure photospheric emission, making them good primary standard candidates. Two stars exhibit source-intrinsic far-infrared excess: β Gem (Pollux), being the host star of a confirmed Jupiter-size exoplanet, due to emission of an associated dust disk, and η Dra due to dust emission in a binary system with a K1 dwarf. The investigation of the 160 μm sky background and environment of four sources reveals significant sky confusion prohibiting the determination of an accurate stellar flux at this wavelength. As a good model approximation, for nine stars we obtain scaling factors of the continuum flux models of four PACS fiducial standards with the same or quite similar spectral type. We can verify a linear dependence of signal-to-noise ratio (S/N) with flux and with square root of time over significant ranges. At 160 μm the latter relation is, however, affected by confusion noise. Conclusions: The PACS faint star sample has allowed a comprehensive sensitivity assessment of the PACS photometer. Accurate photometry allows us to establish a set of five FIR primary standard candidates, namely α Ari, ɛ Lep, ω Cap, HD 41047 and 42 Dra, which are 2-20 times fainter than the faintest PACS fiducial standard (γ Dra) with absolute accuracy of <6%. For three of these primary standard candidates, essential stellar parameters are known, meaning that a dedicated flux model code may be run. Herschel is an ESA space observatory with science instruments provided by European-led Principal Investigator consortia and with important participation from NASA.Tables A.3 to A.5 and B.1 to B.3 are only available in electronic form at the CDS via anonymous ftp to cdsarc.u-strasbg.fr (http://130.79.128.5) or via http://cdsarc.u-strasbg.fr/viz-bin/qcat?J/A+A/613/A40

Added Value of Far-Infrared Radiometry for Ice Cloud Remote Sensing

NASA Astrophysics Data System (ADS)

Libois, Q.; Blanchet, J. P.; Ivanescu, L.; S Pelletier, L.; Laurence, C.

2017-12-01

Several cloud retrieval algorithms based on satellite observations in the infrared have been developed in the last decades. However, most of these observations only cover the midinfrared (MIR, λ < 15 μm) part of the spectrum, and none are available in the far-infrared (FIR, λ ≥ 15 μm). Recent developments in FIR sensors technology, though, now make it possible to consider spaceborne remote sensing in the FIR. Here we show that adding a few FIR channels with realistic radiometric performances to existing spaceborne narrowband radiometers would significantly improve their ability to retrieve ice cloud radiative properties. For clouds encountered in the polar regions and the upper troposphere, where the atmosphere above clouds is sufficiently transparent in the FIR, using FIR channels would reduce by more than 50% the uncertainties on retrieved values of optical thickness, effective particle diameter, and cloud top altitude. This would somehow extend the range of applicability of current infrared retrieval methods to the polar regions and to clouds with large optical thickness, where MIR algorithms perform poorly. The high performance of solar reflection-based algorithms would thus be reached in nighttime conditions. Using FIR observations is a promising venue for studying ice cloud microphysics and precipitation processes, which is highly relevant for cirrus clouds and convective towers, and for investigating the water cycle in the driest regions of the atmosphere.

[Effects of conversion of natural broad-leaved forest to Chinese fir plantation on soil respiration in subtropical China].

PubMed

Zhang, Rui; Bai, Yang; Liu, Juan; Jiang, Pei-kun; Zhou, Guo-mo; Wu, Jia-sen; Tong, Zhi-peng; Li, Yong-fu

2015-10-01

Soil CO2 effluxes in natural broad-leaved forest and the conversed Chinese fir plantation in Linglong Mountains Scenic of Zhejiang Province were evaluated by using static closed chamber and gas chromatography method. The results showed that soil CO2 efflux showed consistent seasonal dynamics in natural broad-leaved forest and Chinese fir plantation, with the maximums observed in summer and autumn, the minimums in winter and spring. Soil CO2 effluxes were 20.0-111.3 and 4.1-118.6 mg C . m-2 . h-1 in natural broad-leaved forest and Chinese fir plantation, respectively. The cumulative soil CO2 emission of natural broad-leaved forest (16.46 t CO2 . hm-2 . a-1) was significantly higher than that of Chinese fir plantation (11.99 t CO2 . hm-2 . a-1). Soil moisture did not affect soil CO2 efflux. There was a significant relationship between soil CO2 efflux and soil temperature at 5 cm depth. There was no significant relationship between soil CO2 efflux of natural broad-leaved forest and water soluble organic carbon content, while water soluble organic carbon content affected significantly soil CO2 efflux in Chinese fir plantation. Converting the natural broad-leaved forest to Chinese fir plantation reduced soil CO2 efflux significantly but improved the sensitivity of soil respiration to environmental factors.

Tree-ring stable isotopes record the impact of a foliar fungal pathogen on CO2 assimilation and growth in Douglas-fir

EPA Science Inventory

Swiss needle cast (SNC) is a fungal disease of Douglas-fir (Pseudotsuga menziesii) that has recently become prevalent in coastal areas of the Pacific Northwest. We used growth measurements and stable isotopes of carbon and oxygen in tree-rings of Douglas-fir and a non-susceptible...

Documentation of the Douglas-fir tussock moth outbreak-population model.

Treesearch

J.J. Colbert; W. Scott Overton; Curtis. White

1979-01-01

Documentation of three model versions: the Douglas-fir tussock moth population-branch model on (1) daily temporal resolution, (2) instart temporal resolution, and (3) the Douglas-fir tussock moth stand-outbreak model; the hierarchical framework and the conceptual paradigm used are described. The coupling of the model with a normal-stand model is discussed. The modeling...

Host resistance screening for balsam woolly adelgid: A comparison of seedlings from 12 fir species

Treesearch

Leslie Newton; John Frampton; Fred Hain

2012-01-01

The balsam woolly adelgid, Adelges piceae (Hemiptera: Adelgidae) (BWA), first reported on Fraser fir, Abies fraseri (Pursh) Poiret, on Mount Mitchell in 1955 (Amman 1966, Boyce 1955), is a major pest in Christmas tree plantations and in native stands. Nearly all Fraser fir Christmas trees produced in North Carolina...

Development of spruce-fir stands following spruce beetle outbreaks

Treesearch

J. M. Schmid; T. E. Hinds

1974-01-01

Logged and unlogged stands of Engelmann spruce-subalpine fir were evaluated in spruce beetle outbreak areas infested about 15, 25, 50, and 100 years ago. Seedling regeneration was generally adequate except in heavily logged areas, although seedlings were often damaged, apparently by animals. Species composition was dramatically altered in favor of fir in the unlogged...

Guide to understory burning in ponderosa pine-larch-fir forests in the Intermountain West

Treesearch

Bruce M. Kilgore; George A. Curtis

1987-01-01

Summarizes the objectives, prescriptions, and techniques used in prescribed burning beneath the canopy of ponderosa pine stands, and stands of ponderosa pine mixed with western larch, Douglas-fir, and grand fir. Information was derived from 12 districts in two USDA Forest Service Regions and seven National Forests in Montana and Oregon.

Rx for Abies: silvicultural options for diseased firs in Oregon and Washington.

Treesearch

G.M. Filip; C.L. Schmitt

1990-01-01

The true firs are important species in Oregon and Washington forests, but root diseases, stem decays, and dwarf mistletoes cause more mortality, growth loss, and cull in these species than in any other. This paper consolidates research, observations, and management techniques for diseases of true firs, especially the effects of silvicultural activities on root diseases...

Resource use and clonal differences in attack rate by the Douglas-fir seed chalcid, Megastigmus spermotrophus Wachtl (Hymenoptera: Torymidae), in France

Treesearch

Nancy Rappaport; Alain Roques

1991-01-01

The within-cone distribution of Megastigmus spermotrophus Wachtl (Hymenoptera: Torymidae), the Douglas-fir seed chalcid, infesting Douglas-fir [Pseudotsuga menziesii (Mirb.) Franco] cones from north-central France was compared with that in samples from California. Results indicate that the mid-region of cones was more intensively...

Decay losses associated with wounds in commercially thinned true fir stands in northern California.

Treesearch

Paul E. Aho; Gary Fiddler; Gregory M. Filip

1989-01-01

A total of 562 white firs (Abies concolor (Gord. & Glend.) Lindl. ex Hildebr.) and red firs (A. magnifica A. Murr.) with logging wounds were felled, dissected, and analyzed for infection and decay in 28 commercially thinned stands on the Klamath and Tahoe National Forests in California. On the Klamath National Forest, decay...

Veneer recovery from Douglas-fir logs.

Treesearch

E.H. Clarke; A.C. Knauss

1957-01-01

During 1956, the Pacific Northwest Forest and Range Experiment Station made a series of six veneer-recovery studies in the Douglas-fir region of Oregon and Washington. The net volume of logs involved totaled approximately 777 M board-feet. Purpose of these studies was to determine volume recovery, by grade of veneer, from the four principal grades of Douglas-fir logs...

Financial analysis of pruning coast Douglas-fir.

Treesearch

Roger D. Fight; James M. Cahlll; Thomas D. Fahey; Thomas A. Snellgrove

1987-01-01

Pruning of coast Douglas-fir was evaluated; recent product recovery information for pruned and unpruned logs for both sawn and peeled products was used. Dimensions of pruned and unpruned trees were simulated with the Douglas-fir stand simulator (DFSIM). Results are presented for a range of sites, ages at time of pruning, ages at time of harvest, product prices, and...

What's in your Douglas-fir bark?

Treesearch

M. Gabriela Buamscha; James E. Altland

2008-01-01

Douglas-fir bark is a common waste product of forest industry, and has potential use as a substrate in container nurseries. Douglas-fir bark (DFB) is strongly acidic and contains amounts of phosphorus, potassium, iron, copper and manganese within or above the levels recommended for growing container crops. As the pH of DFB decreases, electrical conductivity and amounts...

A pioneer exotic tree search for the Douglas-fir region.

Treesearch

Roy R. Silen; Donald L. Olson

1992-01-01

After three-quarters of a century of introduction of 152 conifer and broadleaf species, no promising candidate exotic was found for the Douglas-fir region. Growth curves spanning 50 years or longer are figured for many species. Firs, pines, larches, spruces, hemlocks, and cedars originating in northwestern North America had superior growth rates to those from other...

Behavior of ground vegetation under a partially cut stand of Douglas-fir.

Treesearch

Kenneth W. Krueger

1960-01-01

Environmental changes resulting from logging in the Douglas-fir region often create ideal growing conditions for many woody and herbaceous plants. A rapid increase of brush and low vegetation, in turn, can seriously hinder efforts to establish a new stand. Consequently, one argument against partial cutting in Douglas-fir (Pseudotsuga menziesii) is...

Mortality and growth of dwarf mistletoe-infected red and white fir and the efficacy of thinning for reducing associated losses

Treesearch

H. K. Mehl; S. R. Mori; S. J. Frankel; D. M. Rizzo

2013-01-01

In managed forests dominated by true fir (Abies) species, stands are often restocked using understory trees retained during timber harvest, making the effects of dwarf mistletoe (Arceuthobium spp.) infestation on small true fir a concern. This study examined the response of small red (A. magnifica) and...

Dwarf mistletoe in red and white firs in California–23 to 28 years after inoculation

Treesearch

John R. Parmeter Jr.; Robert F. Scharpf

1989-01-01

Spread and buildup of dwarf mistletoe, Arceuthobium abietinum, was studied on inoculated white fir, Abies concolor, and red fir, A. magnifica, in northern California for 23 to 28 years. At the end of these studies (1986), and in the absence of overstory infection, 13 of 23 trees had dwarf mistletoe populations...

Ecological adaptations in Douglas-fir (Pseudotsuga menziesii var. glauca) populations. III. Central Idaho

Treesearch

Gerald E. Rehfeldt

1983-01-01

Rehfeldt, Gerald E. 1983. Ecological adaptations in Douglas-fir (Pseudotsuga menziesii var. glauca) populations. III. Central Idaho. Canadian Journal of Forest Research. 13: 626-632. Growth, phenology, and cold hardiness of seedlings from 74 populations of Douglas-fir (Pseudotsuga menziesii var. glauca (Beissn.) Franco) from central Idaho were compared in four...

Field performance of stress-laminated highway bridges constructed with glued laminated timber

Treesearch

J.P. Wacker

2004-01-01

This paper summarizes the field performance of three stress-laminated deck timber bridges located in Wisconsin, New York, and Arizona. The deck superstructures of these single-span highway bridges is comprised of full-span glued laminated timber (glulam) beam laminations manufactured with southern pine, hem fir/red maple combination, and/or Douglas fir lumber species....

Growth of white firs defoliated by Modoc budworm in northeastern California

Treesearch

George T. Ferrell

1980-01-01

Open-grown, pole-sized white firs defoliated by Modoc budwonn (Choristoneura viridis) in northeastern California in the years 1959-62 and 1973-75 suffered only minor growth reductions and topkilling compared with the effects that more protracted budworm outbreaks have had elsewhere on their conifer hosts. Growth index analysis indicated that the firs...

A model to estimate noble fir bough weight.

Treesearch

Keith A. Blatner; Roger D. Fight; Nan Vance; Mark Savage; Roger. Chapman

2005-01-01

The harvesting of noble fir (Abies procera) for the production of Christmas wreaths and related products has been a mainstay of the nontimber forest products industry in the Pacific Northwest (PNW) for decades. Although noble fir is the single most important bough product harvested in the PNW, little or no work has been published concerning the...

Use of switched capacitor filters to implement the discrete wavelet transform

NASA Technical Reports Server (NTRS)

Kaiser, Kraig E.; Peterson, James N.

1993-01-01

This paper analyzes the use of IIR switched capacitor filters to implement the discrete wavelet transform and the inverse transform, using quadrature mirror filters (QMF) which have the necessary symmetry for reconstruction of the data. This is done by examining the sensitivity of the QMF transforms to the manufacturing variance in the desired capacitances. The performance is evaluated at the outputs of the separate filter stages and the error in the reconstruction of the inverse transform is compared with the desired results.

EXPLAINING THE [C II]157.7 {mu}m DEFICIT IN LUMINOUS INFRARED GALAXIES-FIRST RESULTS FROM A HERSCHEL/PACS STUDY OF THE GOALS SAMPLE

DOE Office of Scientific and Technical Information (OSTI.GOV)

Diaz-Santos, T.; Armus, L.; Howell, J. H.

We present the first results of a survey of the [C II]157.7 {mu}m emission line in 241 luminous infrared galaxies (LIRGs) comprising the Great Observatories All-sky LIRG Survey (GOALS) sample, obtained with the PACS instrument on board the Herschel Space Observatory. The [C II] luminosities, L{sub [C{sub II]}}, of the LIRGs in GOALS range from {approx}10{sup 7} to 2 Multiplication-Sign 10{sup 9} L{sub Sun }. We find that LIRGs show a tight correlation of [C II]/FIR with far-IR (FIR) flux density ratios, with a strong negative trend spanning from {approx}10{sup -2} to 10{sup -4}, as the average temperature of dustmore » increases. We find correlations between the [C II]/FIR ratio and the strength of the 9.7 {mu}m silicate absorption feature as well as with the luminosity surface density of the mid-IR emitting region ({Sigma}{sub MIR}), suggesting that warmer, more compact starbursts have substantially smaller [C II]/FIR ratios. Pure star-forming LIRGs have a mean [C II]/FIR {approx} 4 Multiplication-Sign 10{sup -3}, while galaxies with low polycyclic aromatic hydrocarbon (PAH) equivalent widths (EWs), indicative of the presence of active galactic nuclei (AGNs), span the full range in [C II]/FIR. However, we show that even when only pure star-forming galaxies are considered, the [C II]/FIR ratio still drops by an order of magnitude, from 10{sup -2} to 10{sup -3}, with {Sigma}{sub MIR} and {Sigma}{sub IR}, implying that the [C II]157.7 {mu}m luminosity is not a good indicator of the star formation rate (SFR) for most local LIRGs, for it does not scale linearly with the warm dust emission most likely associated to the youngest stars. Moreover, even in LIRGs in which we detect an AGN in the mid-IR, the majority (2/3) of galaxies show [C II]/FIR {>=} 10{sup -3} typical of high 6.2 {mu}m PAH EW sources, suggesting that most AGNs do not contribute significantly to the FIR emission. We provide an empirical relation between the [C II]/FIR and the specific SFR for star-forming LIRGs. Finally, we present predictions for the starburst size based on the observed [C II] and FIR luminosities which should be useful for comparing with results from future surveys of high-redshift galaxies with ALMA and CCAT.« less

A polyphase filter for many-core architectures

NASA Astrophysics Data System (ADS)

Adámek, K.; Novotný, J.; Armour, W.

2016-07-01

In this article we discuss our implementation of a polyphase filter for real-time data processing in radio astronomy. The polyphase filter is a standard tool in digital signal processing and as such a well established algorithm. We describe in detail our implementation of the polyphase filter algorithm and its behaviour on three generations of NVIDIA GPU cards (Fermi, Kepler, Maxwell), on the Intel Xeon CPU and Xeon Phi (Knights Corner) platforms. All of our implementations aim to exploit the potential for data reuse that the algorithm offers. Our GPU implementations explore two different methods for achieving this, the first makes use of L1/Texture cache, the second uses shared memory. We discuss the usability of each of our implementations along with their behaviours. We measure performance in execution time, which is a critical factor for real-time systems, we also present results in terms of bandwidth (GB/s), compute (GFLOP/s/s) and type conversions (GTc/s). We include a presentation of our results in terms of the sample rate which can be processed in real-time by a chosen platform, which more intuitively describes the expected performance in a signal processing setting. Our findings show that, for the GPUs considered, the performance of our polyphase filter when using lower precision input data is limited by type conversions rather than device bandwidth. We compare these results to an implementation on the Xeon Phi. We show that our Xeon Phi implementation has a performance that is 1.5 × to 1.92 × greater than our CPU implementation, however is not insufficient to compete with the performance of GPUs. We conclude with a comparison of our best performing code to two other implementations of the polyphase filter, showing that our implementation is faster in nearly all cases. This work forms part of the Astro-Accelerate project, a many-core accelerated real-time data processing library for digital signal processing of time-domain radio astronomy data.

Light Microscopy Module Imaging Tested and Demonstrated

NASA Technical Reports Server (NTRS)

Gati, Frank

2004-01-01

The Fluids Integrated Rack (FIR), a facility-class payload, and the Light Microscopy Module (LMM), a subrack payload, are integrated research facilities that will fly in the U.S. Laboratory module, Destiny, aboard the International Space Station. Both facilities are being engineered, designed, and developed at the NASA Glenn Research Center by Northrop Grumman Information Technology. The FIR is a modular, multiuser scientific research facility that is one of two racks that make up the Fluids and Combustion Facility (the other being the Combustion Integrated Rack). The FIR has a large volume dedicated for experimental hardware; easily reconfigurable diagnostics, power, and data systems that allow for unique experiment configurations; and customizable software. The FIR will also provide imagers, light sources, power management and control, command and data handling for facility and experiment hardware, and data processing and storage. The first payload in the FIR will be the LMM. The LMM integrated with the FIR is a remotely controllable, automated, on-orbit microscope subrack facility, with key diagnostic capabilities for meeting science requirements--including video microscopy to observe microscopic phenonema and dynamic interactions, interferometry to make thin-film measurements with nanometer resolution, laser tweezers to manipulate micrometer-sized particles, confocal microscopy to provide enhanced three-dimensional visualization of structures, and spectrophotometry to measure the photonic properties of materials. Vibration disturbances were identified early in the LMM development phase as a high risk for contaminating the science microgravity environment. An integrated FIR-LMM test was conducted in Glenn's Acoustics Test Laboratory to assess mechanical sources of vibration and their impact to microscopic imaging. The primary purpose of the test was to characterize the LMM response at the sample location, the x-y stage within the microscope, to vibration emissions from the FIR and LMM support structures.

A digital matched filter for reverse time chaos.

PubMed

Bailey, J Phillip; Beal, Aubrey N; Dean, Robert N; Hamilton, Michael C

2016-07-01

The use of reverse time chaos allows the realization of hardware chaotic systems that can operate at speeds equivalent to existing state of the art while requiring significantly less complex circuitry. Matched filter decoding is possible for the reverse time system since it exhibits a closed form solution formed partially by a linear basis pulse. Coefficients have been calculated and are used to realize the matched filter digitally as a finite impulse response filter. Numerical simulations confirm that this correctly implements a matched filter that can be used for detection of the chaotic signal. In addition, the direct form of the filter has been implemented in hardware description language and demonstrates performance in agreement with numerical results.

A digital matched filter for reverse time chaos

NASA Astrophysics Data System (ADS)

Bailey, J. Phillip; Beal, Aubrey N.; Dean, Robert N.; Hamilton, Michael C.

2016-07-01

The use of reverse time chaos allows the realization of hardware chaotic systems that can operate at speeds equivalent to existing state of the art while requiring significantly less complex circuitry. Matched filter decoding is possible for the reverse time system since it exhibits a closed form solution formed partially by a linear basis pulse. Coefficients have been calculated and are used to realize the matched filter digitally as a finite impulse response filter. Numerical simulations confirm that this correctly implements a matched filter that can be used for detection of the chaotic signal. In addition, the direct form of the filter has been implemented in hardware description language and demonstrates performance in agreement with numerical results.

Severe leaching of calcium ions from fir needles caused by acid fog.

PubMed

Igawa, Manabu; Kase, Toshiyuki; Satake, Kosuke; Okochi, Hiroshi

2002-01-01

We have measured the components of the throughfall under fir trees (Abies firma) in the field around Mt. Oyama, where the forest appears to be declining, for the period 1994-1998. Exposure experiments of a simulated acid fog to fir twigs were performed under field conditions. There was a similarity between the acid response in the field and that in the laboratory. In both studies, the severe leaching of calcium ions from the needle surface was caused by exposure to acid fog. We also applied acid fog to fir seedlings over 1 year and observed a decrease in the growth of the seedlings due to this application in the dormant season. These results suggest that the severe leaching of calcium ions due to acid fog may cause the deficiency of calcium and be responsible for the decline of the fir trees.

EXPLICIT LEAST-DEGREE BOUNDARY FILTERS FOR DISCONTINUOUS GALERKIN.

PubMed

Nguyen, Dang-Manh; Peters, Jörg

2017-01-01

Convolving the output of Discontinuous Galerkin (DG) computations using spline filters can improve both smoothness and accuracy of the output. At domain boundaries, these filters have to be one-sided for non-periodic boundary conditions. Recently, position-dependent smoothness-increasing accuracy-preserving (PSIAC) filters were shown to be a superset of the well-known one-sided RLKV and SRV filters. Since PSIAC filters can be formulated symbolically, PSIAC filtering amounts to forming linear products with local DG output and so offers a more stable and efficient implementation. The paper introduces a new class of PSIAC filters NP 0 that have small support and are piecewise constant. Extensive numerical experiments for the canonical hyperbolic test equation show NP 0 filters outperform the more complex known boundary filters. NP 0 filters typically reduce the L ∞ error in the boundary region below that of the interior where optimally superconvergent symmetric filters of the same support are applied. NP 0 filtering can be implemented as forming linear combinations of the data with short rational weights. Exact derivatives of the convolved output are easy to compute.

EXPLICIT LEAST-DEGREE BOUNDARY FILTERS FOR DISCONTINUOUS GALERKIN*

PubMed Central

Nguyen, Dang-Manh; Peters, Jörg

2017-01-01

Convolving the output of Discontinuous Galerkin (DG) computations using spline filters can improve both smoothness and accuracy of the output. At domain boundaries, these filters have to be one-sided for non-periodic boundary conditions. Recently, position-dependent smoothness-increasing accuracy-preserving (PSIAC) filters were shown to be a superset of the well-known one-sided RLKV and SRV filters. Since PSIAC filters can be formulated symbolically, PSIAC filtering amounts to forming linear products with local DG output and so offers a more stable and efficient implementation. The paper introduces a new class of PSIAC filters NP0 that have small support and are piecewise constant. Extensive numerical experiments for the canonical hyperbolic test equation show NP0 filters outperform the more complex known boundary filters. NP0 filters typically reduce the L∞ error in the boundary region below that of the interior where optimally superconvergent symmetric filters of the same support are applied. NP0 filtering can be implemented as forming linear combinations of the data with short rational weights. Exact derivatives of the convolved output are easy to compute. PMID:29081643

Angle-Beam Shear Wave Scattering from Buried Crack-like Defects in Bonded Specimens (Postprint)

DTIC Science & Technology

2017-02-01

wavenumber filtering and spatial windowing is proposed and implemented as an alternative approach to quantify scattering from damage. 15. SUBJECT...TERMS Backscattering . Ultrasonography . Spatial filtering . Ultrasonic scattering . Scattering measurement 16. SECURITY CLASSIFICATION OF: 17...of frequency- wavenumber filtering and spatial windowing is proposed and implemented as an alternative approach to quantify scattering from damage

Implementation of a Parameterized Interacting Multiple Model Filter on an FPGA for Satellite Communications

NASA Technical Reports Server (NTRS)

Hackett, Timothy M.; Bilen, Sven G.; Ferreira, Paulo Victor R.; Wyglinski, Alexander M.; Reinhart, Richard C.

2016-01-01

In a communications channel, the space environment between a spacecraft and an Earth ground station can potentially cause the loss of a data link or at least degrade its performance due to atmospheric effects, shadowing, multipath, or other impairments. In adaptive and coded modulation, the signal power level at the receiver can be used in order to choose a modulation-coding technique that maximizes throughput while meeting bit error rate (BER) and other performance requirements. It is the goal of this research to implement a generalized interacting multiple model (IMM) filter based on Kalman filters for improved received power estimation on software-dened radio (SDR) technology for satellite communications applications. The IMM filter has been implemented in Verilog consisting of a customizable bank of Kalman filters for choosing between performance and resource utilization. Each Kalman filter can be implemented using either solely a Schur complement module (for high area efficiency) or with Schur complement, matrix multiplication, and matrix addition modules (for high performance). These modules were simulated and synthesized for the Virtex II platform on the JPL Radio Experimenter Development System (EDS) at NASA Glenn Research Center. The results for simulation, synthesis, and hardware testing are presented.

A Low Cost Structurally Optimized Design for Diverse Filter Types

PubMed Central

Kazmi, Majida; Aziz, Arshad; Akhtar, Pervez; Ikram, Nassar

2016-01-01

A wide range of image processing applications deploys two dimensional (2D)-filters for performing diversified tasks such as image enhancement, edge detection, noise suppression, multi scale decomposition and compression etc. All of these tasks require multiple type of 2D-filters simultaneously to acquire the desired results. The resource hungry conventional approach is not a viable option for implementing these computationally intensive 2D-filters especially in a resource constraint environment. Thus it calls for optimized solutions. Mostly the optimization of these filters are based on exploiting structural properties. A common shortcoming of all previously reported optimized approaches is their restricted applicability only for a specific filter type. These narrow scoped solutions completely disregard the versatility attribute of advanced image processing applications and in turn offset their effectiveness while implementing a complete application. This paper presents an efficient framework which exploits the structural properties of 2D-filters for effectually reducing its computational cost along with an added advantage of versatility for supporting diverse filter types. A composite symmetric filter structure is introduced which exploits the identities of quadrant and circular T-symmetries in two distinct filter regions simultaneously. These T-symmetries effectually reduce the number of filter coefficients and consequently its multipliers count. The proposed framework at the same time empowers this composite filter structure with additional capabilities of realizing all of its Ψ-symmetry based subtypes and also its special asymmetric filters case. The two-fold optimized framework thus reduces filter computational cost up to 75% as compared to the conventional approach as well as its versatility attribute not only supports diverse filter types but also offers further cost reduction via resource sharing for sequential implementation of diversified image processing applications especially in a constraint environment. PMID:27832133

Coarse woody debris in a Southern Appalachian spruce-fir forest of the Great Smoky Mountains National Park

Treesearch

Anita K. Rose; N.S. Nicholas

2008-01-01

Spruce-fir forests in the southern Appalachian Mountains receive high atmospheric nitrogen inputs and have high nitrate levels in soil solution and streamwater. High levels of excess nitrogen have been associated with reduced tree vigor. Additionally, the balsam woolly adelgid (Adelges piceae Ratz.) has killed the majority of endemic Fraser fir [

An examination of the genetic control of Douglas-fir vascular tissue phytochemicals: implications for black bear foraging.

Treesearch

Bruce A. Kimball; G.R. Johnson; Dale L. Nolte; Doreen L. Griffin

1999-01-01

Silvicultural practices can influence black bear (Ursus americanus) foraging preferences for Douglas-fir (Pseudotsuga menziesii) cambial-zone vascular tissues, but little is known about the role of genetics. To study the impact of genetic selection, vascular tissue samples were collected from Douglas-fir trees in six half-sib families from five...

Early survival and height growth of Douglas-fir and lodgepole pine seedlings and variations in site factors following treatment of logging residues.

Treesearch

W. Lopushlnsky; D. Zabowskl; T.D. Anderson

1992-01-01

Logging residues were broadcast burned, piled and burned, removed, or left in place after clearcutting in a high-elevation subalpine fir (Abies lasiocarpa (Hook.) Nutt.) lodgepole pine (Pinus contorta Dougl. ex Loud.) forest in north-central Washington. Survival, height growth and foliar nutrient content of planted Douglas-fir...

Assessing the effects of vegetation types on carbon storage fifteen years after reforestation on a Chinese fir site

Treesearch

Qinkui Wang; Silong Wang; Jianwei Zhang

2009-01-01

Forest ecosystems play a significant role in sequestering carbon (C) in biomass and soils. Plantations established in subtropical China since the 1980s, mainly of Chinese fir (Cunninghamia lanceolata (Lamb.) Hook) in monocultures, have proved to be major C sinks. However, information is lacking about whether mixing Chinese fir with broadleaved tree...

Conifer-Ceanothus interactions influence tree growth before and after shrub removal in a forest plantation in the western Cascade Mountains, USA.

Treesearch

Heather E. Erickson; Constance A. Harrington

2006-01-01

Ceanothus velutinous is often considered to be an aggressive competitor with young conifers in the western United States. Using a conifer (noble fir, Pacific silver fir, Douglas-fir, and western hemlock) plantation in western WA where Ceanothus had become established, we assessed how conifer-shrub crown interactions affected...

Probability of infestation and extent of mortality associated with the Douglas-fir beetle in the Colorado Front Range

Treesearch

Jose F. Negron

1998-01-01

Infested and uninfested areas within Douglas fir, Pseudotsuga menziesii Mirb.. Franco, stands affected by the Douglas-fir beetle, Dendroctonus pseudotsugae Hopk. were sampled in the Colorado Front Range, CO. Classification tree models were built to predict probabilities of infestation. Regression trees and linear regression analysis were used to model amount of tree...

How to identify brooms in Douglas-fir caused by dwarf mistletoe.

Treesearch

Robert O. Tinnin; Donald M. Knutson

1985-01-01

Dwarf mistletoe causes obvious brooms in Douglas-fir. The brooms are the easiest means of recognizing the presence of dwarf mistletoe; however, dwarf mistletoe is not the only cause of brooming in Douglas-fir. Therefore, accurate identification of dwarf mistletoe brooms is important. If no evidence of aerial shoots can be found in the brooms, and if the brooms occur...

Within-stand spatial distribution of tree mortality caused by the Douglas-Fir beetle (Coleoptera: Scolytidae)

Treesearch

Jose F. Negron; John A. Anhold; A. Steve Munson

2001-01-01

The Douglas-fir beetle, Dendroctonus pseudotsugae Hopkins, causes considerable mortality in Douglas-fir, Pseudotsuga menziesii (Mirb.) Franco, forests. Within-stand distribution of mortality was examined in affected stands using geostatistical techniques. A 10 x 10 m grid was established in two 4-ha study sites. Live and beetle-killed host basal area was measured at...

A ponderosa pine-grand fir spacing study in central Oregon: results after 10 years.

Treesearch

K.W. Seidel

1985-01-01

The 10-year growth response from an initial spacing study established in a ponderosa pine (Pinus ponderosa Dougl, ex Laws.) and grand fir (Abies grandis (Dougl. ex D. Don) Lindl.) plantation was measured in central Oregon. The study was designed to compare the growth rates of pure pine, pure fir, and a 50-percent mixture of...

Seedfall and seed viability within artificial canopy gaps in a western Washington douglas-fir forest

Treesearch

Warren D. Devine; Timothy B. Harrington

2015-01-01

Seedfall of coast Douglas-fir (Pseudotsuga menziesii [Mirb.] Franco var. menziesii) has been studied at the forest edge-clearcut interface and in small canopy gaps, but it has not been evaluated in gap sizes that would be typical of a group-selection method of regeneration. In a mature Douglas-fir forest in the Puget Sound...

Site index curves for white fir in the southwestern United States developed using a guide curve method

Treesearch

Robert L. Mathiasen; William K. Olsen; Carleton B. Edminster

2006-01-01

Site index curves for white fir (Abies concolor) in Arizona, New Mexico, and southwestern Colorado were developed using height-age measurements and an estimated guide curve and 95% confidence intervals for individual predictions. The curves were developed using height-age data for 1,048 white firs from 263 study sites distributed across eight...

White fur lumber recovery at a western Washington sawmill.

Treesearch

E.E. Matson

1957-01-01

In April 1956 a study was made in western Washington to determine grades of lumber that could be expected from silver fir (Abies amabilis) and grand fir (Abies grandis) which are grouped together the lumber industry and sold as white fir. At the sawmill where the study was made, none of the lumber is seasoned and most of it is...

True fir spacing and yield trials—20-year update

Treesearch

Robert O. Curtis

2013-01-01

This report updates data and comparisons from previous reports (Curtis and others 2000, Curtis 2008) on a series of precommercial thinning and yield trials in high-elevation true fir–hemlock stands, using data from the 12 replicates for which 20-year data are now available. The stands were varying mixtures of Pacific silver fir (Abies amabilis (Douglas ex Loudon)...

Natural regeneration of Douglas-fir and associated species using modified clear-cutting systems in the Oregon Cascades.

Treesearch

Jerry F. Franklin

1963-01-01

Clear cutting is the standard harvesting system in old-growth Douglas-fir (Pseudotsuga menziesii) forests in the Pacific Northwest. Usually these clear cuts are in "staggered settings" of 15 to 80 acres with the surrounding stand left uncut to provide seed and serve as a firebreak. However, satisfactory natural regeneration of Douglas-fir...

Flight periodicity of the Douglas-fir beetle, Dendroctonus pseudotsugae Hopkins (Coleoptera: Curculionidae: Scolytinae) in Colorado, U.S.A

Treesearch

Jose F. Negron; Willis C. Schaupp; Lee Pederson

2011-01-01

There are about 500 species of bark beetles (Coleoptera: Curculionidae: Scolytinae) in the United States (Wood 1982). A number of them are important disturbance agents in forested ecosystems, occasionally creating large tracts of dead trees. One eruptive species is the Douglas-fir beetle, Dendroctonus pseudotsugae Hopkins, which utilizes Douglas-fir, Pseudotsuga...

Thinning balsam fir thickets with soil sterilants

Treesearch

Arthur C. Hart

1961-01-01

Under certain conditions that we do not yet fully understand, balsam fir has a tendency to form dense thickets that cause stagnation of growth. This condition is common throughout the spruce-fir region, and it presents the landowner with one of his most perplexing management problems. A typical thicket averaging 15 feet tall may contain 5,000 to 10,000 stems per acre (...

Selected yield tables for plantations and natural stands in Inland Northwest Forests

Treesearch

Albert R. Stage; David L. Renner; Roger C. Chapman

1988-01-01

Yields arrayed by site index and age have been tabulated for plantations of 500 trees per acre, with five thinning regimes, for Douglas-fir, grand fir, and western larch. Yields were also tabulated for naturally regenerated stands of the grand fir-cedar-hemlock ecosystem of the Inland Empire. All yields were estimated with the Prognosis Model for Stand Development,...

Changes in wood product proportions in the Douglas-fir region with respect to size, age, and time.

Treesearch

R.A. Monserud; X. Zhou

2007-01-01

We examine both the variation and the changing proportions of different wood products obtained from trees and logs in the Douglas-fir region of the Northwestern United States. Analyses are based on a large product recovery database covering over 40 years of recovery studies; 13 studies are available for Douglas-fir (Pseudotsuga menziesii (Mirb.)...

Five-year field trials using preservative-treated, second-growth Douglas-fir exposed in ground contact in Australia

Treesearch

Rodney C. De Groot; Douglas M. Crawford; Jack Norton; John Keith

2000-01-01

The durability of preservative-treated stakes of second-growth Coastal Douglas-fir was evaluated in a field plot in northern Queensland, Australia. Results from this field trial indicate that second-growth Douglas-fir can be treated with preservatives to meet Australian standards and will provide long-term durability in adverse environments. Data presented indicate...

Height growth and site index curves for Douglas-fir on dry sites in the Willamette National Forest.

Treesearch

Joseph E Means; Mary E. Helm

1985-01-01

Equations and curves are presented for estimating height and site index of Douglas-fir (Pseudotsuga menziesii (Mirb.) Franco) on hot, dry sites in the Willamette National Forest in western Oregon. The equations are based on the dissected stems of 27 trees. The curves differ from those previously published for Douglas-fir. Instructions are presented...

Annosus Root Disease in True Firs in Northern and Central California National Forests

Treesearch

G. W. Slaughter; J. R. Parmeter Jr.

1989-01-01

True fir stands in California (3.5 million acres) were surveyed during 1979-1980 to estimate the prevalence of infection by Heterobasidion annosum, and to determine stand and tree characteristics associated with the occurrence of annosus root disease. Approximately 4 percent (1.46 billion board-feet) of the live true firs were estimated to be...

Stand development 18 years after gap creation in a uniform Douglas-fir plantation

Treesearch

Robert O. Curtis; Constance A. Harrington; Leslie C. Brodie

2017-01-01

This report gives early results, 18 years after treatment and 30 years after planting, from a trial of early thinning and gap creation intended to increase biodiversity in a very uniform extensive Douglas-fir plantation. Gap creation has introduced canopy irregularity and a substantial hemlock component into what was originally a very uniform pure Douglas-fir...

The distribution of genets and their nuclear composition reveal the dynamics of establishment and survival of Heterobasidion annosum in white fir stands

Treesearch

M. Garbelotto; F.W. Cobb; T.D. Bruns; W. Otrosina; T. Popenuck; Garey Slaughter

1998-01-01

The structure of Heterobasidiom annosum populations in white fir was studied in 15 mixed conifer sites of central and northern California. Areas selected for the study displayed mortality of white fir trees in enlarging discrete patches (mortality centers). At each site, fungal genotypes were defined by somatic compatibility tests...

Fir sawyer beetle-Siberian fir interaction modeling: resistance of fir stands to insect outbreaks

Treesearch

Tamara M. Ovtchinnikova; Victor V. Kiselev

1991-01-01

Entomological monitoring is part of a total ecological monitoring system. Its purpose is the identification, prognosis, and estimation of forest ecosystem impacts induced by insects. The entomological monitoring of a forest is based on a clear understanding of the role played by insects in forest ecosystems. The patterns of insect population dynamics in space and time...

Source identification of western Oregon Douglas-fir wood cores using mass spectrometry and random forest classification.

PubMed

Finch, Kristen; Espinoza, Edgard; Jones, F Andrew; Cronn, Richard

2017-05-01

We investigated whether wood metabolite profiles from direct analysis in real time (time-of-flight) mass spectrometry (DART-TOFMS) could be used to determine the geographic origin of Douglas-fir wood cores originating from two regions in western Oregon, USA. Three annual ring mass spectra were obtained from 188 adult Douglas-fir trees, and these were analyzed using random forest models to determine whether samples could be classified to geographic origin, growth year, or growth year and geographic origin. Specific wood molecules that contributed to geographic discrimination were identified. Douglas-fir mass spectra could be differentiated into two geographic classes with an accuracy between 70% and 76%. Classification models could not accurately classify sample mass spectra based on growth year. Thirty-two molecules were identified as key for classifying western Oregon Douglas-fir wood cores to geographic origin. DART-TOFMS is capable of detecting minute but regionally informative differences in wood molecules over a small geographic scale, and these differences made it possible to predict the geographic origin of Douglas-fir wood with moderate accuracy. Studies involving DART-TOFMS, alone and in combination with other technologies, will be relevant for identifying the geographic origin of illegally harvested wood.

FIR statistics of paired galaxies

NASA Technical Reports Server (NTRS)

Sulentic, Jack W.

1990-01-01

Much progress has been made in understanding the effects of interaction on galaxies (see reviews in this volume by Heckman and Kennicutt). Evidence for enhanced emission from galaxies in pairs first emerged in the radio (Sulentic 1976) and optical (Larson and Tinsley 1978) domains. Results in the far infrared (FIR) lagged behind until the advent of the Infrared Astronomy Satellite (IRAS). The last five years have seen numerous FIR studies of optical and IR selected samples of interacting galaxies (e.g., Cutri and McAlary 1985; Joseph and Wright 1985; Kennicutt et al. 1987; Haynes and Herter 1988). Despite all of this work, there are still contradictory ideas about the level and, even, the reality of an FIR enhancement in interacting galaxies. Much of the confusion originates in differences between the galaxy samples that were studied (i.e., optical morphology and redshift coverage). Here, the authors report on a study of the FIR detection properties for a large sample of interacting galaxies and a matching control sample. They focus on the distance independent detection fraction (DF) statistics of the sample. The results prove useful in interpreting the previously published work. A clarification of the phenomenology provides valuable clues about the physics of the FIR enhancement in galaxies.

Space Shuttle Main Engine High Pressure Fuel Turbopump Turbine Blade Cracking

NASA Technical Reports Server (NTRS)

Lee, Henry

1988-01-01

The analytical results from two-dimensional (2D) and three-dimensional (3D) finite element model investigations into the cracking of Space Shuttle Main Engine (SSME) High Pressure Fuel Turbopump (HPFTP) first- and second-stage turbine blades are presented. Specifically, the initiation causes for transverse cracks on the pressure side of the firststage blade fir tree lobes and face/corner cracks on the downstream fir tree face of the second-state blade are evaluated. Because the blade material, MAR-M-246 Hf (DS), is highly susceptible to hydrogen embrittlement in the -100 F to 400 F thermal environment, a steady-state condition (full power level = 109 percent) rather than a start-up or shut-down transient was considered to be the most likely candidate for generating a high-strain state in the fir tree areas. Results of the analyses yielded strain levels on both first- and second-stage blade fir tree regions that are of a magnitude to cause hydrogen assisted low cycle fatigue cracking. Also evident from the analysis is that a positive margin against fir tree cracking exists for the planned design modifications, which include shot peening for both first- and second-stage blade fir tree areas.

Digital Signal Processing Techniques for the GIFTS SM EDU

NASA Technical Reports Server (NTRS)

Tian, Jialin; Reisse, Robert A.; Gazarik, Michael J.

2007-01-01

The Geosynchronous Imaging Fourier Transform Spectrometer (GIFTS) Sensor Module (SM) Engineering Demonstration Unit (EDU) is a high resolution spectral imager designed to measure infrared (IR) radiance using a Fourier transform spectrometer (FTS). The GIFTS instrument employs three Focal Plane Arrays (FPAs), which gather measurements across the long-wave IR (LWIR), short/mid-wave IR (SMWIR), and visible spectral bands. The raw interferogram measurements are radiometrically and spectrally calibrated to produce radiance spectra, which are further processed to obtain atmospheric profiles via retrieval algorithms. This paper describes several digital signal processing (DSP) techniques involved in the development of the calibration model. In the first stage, the measured raw interferograms must undergo a series of processing steps that include filtering, decimation, and detector nonlinearity correction. The digital filtering is achieved by employing a linear-phase even-length FIR complex filter that is designed based on the optimum equiripple criteria. Next, the detector nonlinearity effect is compensated for using a set of pre-determined detector response characteristics. In the next stage, a phase correction algorithm is applied to the decimated interferograms. This is accomplished by first estimating the phase function from the spectral phase response of the windowed interferogram, and then correcting the entire interferogram based on the estimated phase function. In the calibration stage, we first compute the spectral responsivity based on the previous results and the ideal Planck blackbody spectra at the given temperatures, from which, the calibrated ambient blackbody (ABB), hot blackbody (HBB), and scene spectra can be obtained. In the post-calibration stage, we estimate the Noise Equivalent Spectral Radiance (NESR) from the calibrated ABB and HBB spectra. The NESR is generally considered as a measure of the instrument noise performance, and can be estimated as the standard deviation of calibrated radiance spectra from multiple scans. To obtain an estimate of the FPA performance, we developed an efficient method of generating pixel performance assessments. In addition, a random pixel selection scheme is developed based on the pixel performance evaluation. This would allow us to perform the calibration procedures on a random pixel population that is a good statistical representation of the entire FPA. The design and implementation of each individual component will be discussed in details.

Prospective implementation of an algorithm for bedside intravascular ultrasound-guided filter placement in critically ill patients.

PubMed

Killingsworth, Christopher D; Taylor, Steven M; Patterson, Mark A; Weinberg, Jordan A; McGwin, Gerald; Melton, Sherry M; Reiff, Donald A; Kerby, Jeffrey D; Rue, Loring W; Jordan, William D; Passman, Marc A

2010-05-01

Although contrast venography is the standard imaging method for inferior vena cava (IVC) filter insertion, intravascular ultrasound (IVUS) imaging is a safe and effective option that allows for bedside filter placement and is especially advantageous for immobilized critically ill patients by limiting resource use, risk of transportation, and cost. This study reviewed the effectiveness of a prospectively implemented algorithm for IVUS-guided IVC filter placement in this high-risk population. Current evidence-based guidelines were used to create a clinical decision algorithm for IVUS-guided IVC filter placement in critically ill patients. After a defined lead-in phase to allow dissemination of techniques, the algorithm was prospectively implemented on January 1, 2008. Data were collected for 1 year using accepted reporting standards and a quality assurance review performed based on intent-to-treat at 6, 12, and 18 months. As defined in the prospectively implemented algorithm, 109 patients met criteria for IVUS-directed bedside IVC filter placement. Technical feasibility was 98.1%. Only 2 patients had inadequate IVUS visualization for bedside filter placement and required subsequent placement in the endovascular suite. Technical success, defined as proper deployment in an infrarenal position, was achieved in 104 of the remaining 107 patients (97.2%). The filter was permanent in 21 (19.6%) and retrievable in 86 (80.3%). The single-puncture technique was used in 101 (94.4%), with additional dual access required in 6 (5.6%). Periprocedural complications were rare but included malpositioning requiring retrieval and repositioning in three patients, filter tilt >/=15 degrees in two, and arteriovenous fistula in one. The 30-day mortality rate for the bedside group was 5.5%, with no filter-related deaths. Successful placement of IVC filters using IVUS-guided imaging at the bedside in critically ill patients can be established through an evidence-based prospectively implemented algorithm, thereby limiting the need for transport in this high-risk population. Copyright (c) 2010 Society for Vascular Surgery. Published by Mosby, Inc. All rights reserved.

GPU Acceleration of DSP for Communication Receivers.

PubMed

Gunther, Jake; Gunther, Hyrum; Moon, Todd

2017-09-01

Graphics processing unit (GPU) implementations of signal processing algorithms can outperform CPU-based implementations. This paper describes the GPU implementation of several algorithms encountered in a wide range of high-data rate communication receivers including filters, multirate filters, numerically controlled oscillators, and multi-stage digital down converters. These structures are tested by processing the 20 MHz wide FM radio band (88-108 MHz). Two receiver structures are explored: a single channel receiver and a filter bank channelizer. Both run in real time on NVIDIA GeForce GTX 1080 graphics card.

Optical implementation of the synthetic discriminant function

NASA Astrophysics Data System (ADS)

Butler, S.; Riggins, J.

1984-10-01

Much attention is focused on the use of coherent optical pattern recognition (OPR) using matched spatial filters for robotics and intelligent systems. The OPR problem consists of three aspects -- information input, information processing, and information output. This paper discusses the information processing aspect which consists of choosing a filter to provide robust correlation with high efficiency. The filter should ideally be invariant to image shift, rotation and scale, provide a reasonable signal-to-noise (S/N) ratio and allow high throughput efficiency. The physical implementation of a spatial matched filter involves many choices. These include the use of conventional holograms or computer-generated holograms (CGH) and utilizing absorption or phase materials. Conventional holograms inherently modify the reference image by non-uniform emphasis of spatial frequencies. Proper use of film nonlinearity provides improved filter performance by emphasizing frequency ranges crucial to target discrimination. In the case of a CGH, the emphasis of the reference magnitude and phase can be controlled independently of the continuous tone or binary writing processes. This paper describes computer simulation and optical implementation of a geometrical shape and a Synthetic Discriminant Function (SDF) matched filter. The authors chose the binary Allebach-Keegan (AK) CGH algorithm to produce actual filters. The performances of these filters were measured to verify the simulation results. This paper provides a brief summary of the matched filter theory, the SDF, CGH algorithms, Phase-Only-Filtering, simulation procedures, and results.

Proceedings of Annual Acquisition Research Symposium (7th), Hershey, Pennsylvania, 31 May-2 Jun 1978

DTIC Science & Technology

1978-06-01

strongly, with DCS/Plans our efforts going during difficult periods, and Operation leadership and heavy MAJCOM but mission area planning and analysis is...implementing DOD required with heavy participation by AFSC. Directives 5000.1 and 5000.2 require new pro- Zero-Base Budgeting is the third part of the...Mission Area Analysis portion, it it -omposed of three logical steps. The fir-t .?p de - velops viable alternatives for tae -.. R&D programs. The second

Real time microcontroller implementation of an adaptive myoelectric filter.

PubMed

Bagwell, P J; Chappell, P H

1995-03-01

This paper describes a real time digital adaptive filter for processing myoelectric signals. The filter time constant is automatically selected by the adaptation algorithm, giving a significant improvement over linear filters for estimating the muscle force and controlling a prosthetic device. Interference from mains sources often produces problems for myoelectric processing, and so 50 Hz and all harmonic frequencies are reduced by an averaging filter and differential process. This makes practical electrode placement and contact less critical and time consuming. An economic real time implementation is essential for a prosthetic controller, and this is achieved using an Intel 80C196KC microcontroller.

Separation of man-made and natural patterns in high-altitude imagery of agricultural areas

NASA Technical Reports Server (NTRS)

Samulon, A. S.

1975-01-01

A nonstationary linear digital filter is designed and implemented which extracts the natural features from high-altitude imagery of agricultural areas. Essentially, from an original image a new image is created which displays information related to soil properties, drainage patterns, crop disease, and other natural phenomena, and contains no information about crop type or row spacing. A model is developed to express the recorded brightness in a narrow-band image in terms of man-made and natural contributions and which describes statistically the spatial properties of each. The form of the minimum mean-square error linear filter for estimation of the natural component of the scene is derived and a suboptimal filter is implemented. Nonstationarity of the two-dimensional random processes contained in the model requires a unique technique for deriving the optimum filter. Finally, the filter depends on knowledge of field boundaries. An algorithm for boundary location is proposed, discussed, and implemented.

A digital matched filter for reverse time chaos

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bailey, J. Phillip, E-mail: mchamilton@auburn.edu; Beal, Aubrey N.; Dean, Robert N.

2016-07-15

The use of reverse time chaos allows the realization of hardware chaotic systems that can operate at speeds equivalent to existing state of the art while requiring significantly less complex circuitry. Matched filter decoding is possible for the reverse time system since it exhibits a closed form solution formed partially by a linear basis pulse. Coefficients have been calculated and are used to realize the matched filter digitally as a finite impulse response filter. Numerical simulations confirm that this correctly implements a matched filter that can be used for detection of the chaotic signal. In addition, the direct form ofmore » the filter has been implemented in hardware description language and demonstrates performance in agreement with numerical results.« less

Differential Gene Expression Reveals Candidate Genes for Drought Stress Response in Abies alba (Pinaceae)

PubMed Central

Ziegenhagen, Birgit; Liepelt, Sascha

2015-01-01

Increasing drought periods as a result of global climate change pose a threat to many tree species by possibly outpacing their adaptive capabilities. Revealing the genetic basis of drought stress response is therefore implemental for future conservation strategies and risk assessment. Access to informative genomic regions is however challenging, especially for conifers, partially due to their large genomes, which puts constraints on the feasibility of whole genome scans. Candidate genes offer a valuable tool to reduce the complexity of the analysis and the amount of sequencing work and costs. For this study we combined an improved drought stress phenotyping of needles via a novel terahertz water monitoring technique with Massive Analysis of cDNA Ends to identify candidate genes for drought stress response in European silver fir (Abies alba Mill.). A pooled cDNA library was constructed from the cotyledons of six drought stressed and six well-watered silver fir seedlings, respectively. Differential expression analyses of these libraries revealed 296 candidate genes for drought stress response in silver fir (247 up- and 49 down-regulated) of which a subset was validated by RT-qPCR of the twelve individual cotyledons. A majority of these genes code for currently uncharacterized proteins and hint on new genomic resources to be explored in conifers. Furthermore, we could show that some traditional reference genes from model plant species (GAPDH and eIF4A2) are not suitable for differential analysis and we propose a new reference gene, TPC1, for drought stress expression profiling in needles of conifer seedlings. PMID:25924061

Six-year growth of Douglas-fir saplings after manual or herbicide release from coastal shrub competition.

Treesearch

William I. Stein

1999-01-01

Survival and growth of planted Douglas-fir (Pseudotsuga menziesii) saplings and associated shrubs were observed for 6 years after seven release treatments had been applied, side by, side on four areas in the Coast Range of Oregon. Four times as much Douglas-fir volume as in the control was produced by one manual cutting of shrubs, which also...

Foliage Consumption by 6th-Instar Spruce Budworm Larvae, Choristoneura fumiferana (Clem.) Feeding on Balsam Fir and White Spruce

Treesearch

A.W.  Thomas

1983-01-01

Female larvae ate about 1.5 times as much foliage as male larvae. Larvae ate significantly less old foliage than current foliage. Balsam fir current foliage was eaten in greater quantitities than any other foliage; white spruce current and balsam fir old were eaten to the same extent; very little old white spruce was eaten.

Stereo photo series for quantifying forest residues in the Douglas-Fir-Hemlock type of the Willamette National Forest.

Treesearch

Roger D. Ottmar; Colin C. Hardy; Robert E. Vihnanek

1990-01-01

A series of stereo photographs displays a range of residue loadings for harvested units in the Douglas-fir-western hemlock cover type common to the Willamette National Forest. Postburn residue levels are also represented for the Douglas-fir-western hemlock types. Information with each photo includes measured quadratic means and weights for various size classes, woody...

White fir stands killed by tussock moth...70-mm. color photography aids detection

Treesearch

Steven L. Wert; Boyd E. Wickman

1968-01-01

The use of large-scale 70 mm. aerial photography proved to be an effective technique for detecting trees in white fir stands killed by Douglas-fir tussock moth in northeastern California. Correlations between ground and photo estimates of dead trees were high. But correlations between such estimates of lesser degrees of tree damage--thin tops and topkill--were much...

Genetic diversity and seed production in Santa Lucia fir (Abies bracteata),a relict of the Miocene broadleaved evergreen forest

Treesearch

F. Thomas Ledig; Paul D. Hodgskiss; David R. Johnson

2006-01-01

Santa Lucia fir (Abies bracteata), is a unique fir, the sole member of the subgenus Pseudotorreya. It is a relict of the Miocene broadleaved evergreen sclerophyll forest, and is now restricted to a highly fragmented range in the Santa Lucia Mountains of central coastal California. Expected heterozygosity for 30 isozyme loci in 18 enzyme systems...

Optimal uneven-aged stocking guides: an application to spruce-fir stands in New England

Treesearch

Jeffrey H. Gove; Mark J. Ducey

2014-01-01

Management guides for uneven-aged forest stands periodically need to be revisited and updated based on new information and methods. The current silvicultural guide for uneven-aged spruce-fir management in Maine and the northeast (Frank, R.M. and Bjorkbom, J.C. 1973 A silvicultural guide for spruce-fir in the northeast. General Technical Report NE-6, Forest Service. U.S...

Projected future suitable habitat and productivity of Douglas-fir in western North America

Treesearch

Aaron R. Weiskittel; Nicholas L. Crookston; Gerald E. Rehfeldt

2012-01-01

Douglas-fir (Pseudotsuga menziesii [Mirb.] Franco) is one of the most common and commercially important species in western North America. The species can occupy a range of habitats, is long-lived (up to 500 years), and highly productive. However, the future of Douglas-fir in western North America is highly uncertain due to the expected changes in climate conditions....

Effects of soil calcium and aluminum on the physiology of balsam fir and red spruce saplings in northern New England

Treesearch

Richard L. Boyce; Paul G. Schaberg; Gary J. Hawley; Joshua M. Halman; Paula F. Murakami

2013-01-01

We examined the influence of calcium (Ca) and aluminum (Al) nutrition on the foliar physiology of red spruce (Picea rubens Sarg.) and balsam fir [Abies balsamea (L.) Mill.] in northern New England, USA. At the Hubbard Brook Experimental Forest (NH, USA), spruce and fir saplings were sampled from control, Al-, and Ca-supplemented...

The selection system of silviculture in spruce-fir stands - procedures, early results, and comparisons with unmanaged stands

Treesearch

Robert M. Frank; Barton M. Blum

1978-01-01

Early results after 20 years of record keeping indicate that spruce-fir stands will respond to the selection system of silviculture. Stand quality is improved, species composition can be altered, diameter-class distribution approaches a stated goal, stand density is controlled, and yields are increased. Selection silviculture in spruce-fir can now be compared to early...

Conversion of SPORL pretreated Douglas fir forest residues into microbial lipids with oleaginous yeasts

Treesearch

Bruce S. Dien; Junyong Zhu; Patricia J. Slininger; Cletus P. Kurtzman; Bryan R. Moser; Patricia J. O' Bryan; Roland Gleisner; Michael A. Cotta

2016-01-01

Douglas fir is the dominant commercial tree grown in the United States. In this study Douglas fir residue was converted to single cell oils (SCO) using oleaginous yeasts. Monosaccharides were extracted from the woody biomass by pretreating with sulfite and dilute sulfuric acid (SPORL process) and hydrolyzing using commercial cellulases. A new SPORL process that uses pH...

A comparison of postburn woodpecker foraging use of white fir (Abies concolor) and Jeffrey Pine (Pinus jeffreyi)

Treesearch

Kerry L. Farris; Steve Zack

2008-01-01

We examined the temporal patterns of the structural decay, insect infestation and woodpecker foraging patterns on white-fir and yellow pine following a prescribed burn in Lassen National Park, CA. Our objectives were to: 1) describe how pine and fir differ in their decay patterns and insect activity, and 2) determine how these differences reflect woodpecker foraging...

Lumber recovery from young-growth red and white fir in northern California.

Treesearch

W.Y. Pong

1982-01-01

Lumber recovery data from 1,106 logs from 341 young-growth white fir (Abies concolor (Gord. & Glend.) Lindl. ex Hildebr.) and red fir (A. magnifica A. Murr) trees are presented. All logs were processed through a quad-band headsaw. Nominal 2x4's and 2x6's made up over 93 percent of the lumber volume; nearly 70...

Mortality and growth reduction of white fir following defoliation by the Douglas-fir tussock moth

Treesearch

Boyd E. Wickman

1963-01-01

In 5 years after a 1954-56 outbreak of Hemerocampa pseudotsugata in Calaveras and Tuolumne Counties, California, 20 percent of the merchantable white fir, or 11,071 board feet per acre, died in heavily defoliated stands. Another 1,113 board feet per acre was lost owing to radial growth reductions in partly defoliated trees; 12 percent of these trees...

Dimension lumber grades from white fir in Lakeview area.

Treesearch

E.E. Matson

1955-01-01

Production of white fir lumber in the western pine region amounted to a little more than a billion board feet in 1954, or about 13 percent of the output of pine-region sawmills. Moreover, production of the white fir lumber is expanding, and it is important to know what grades of lumber can be expected so that timber and log values can be more accurately appraised....

Released advance reproduction of white and red fir. . . growth, damage, mortality

Treesearch

Donald T. Gordon

1973-01-01

Advance reproduction of white fir and red fir released by cutting overmature over-story was studied at the Swain Mountain Experimental Forest in northern California, at 6,300 feet elevation. Seedling and sapling height growth before logging was only 0.1-0.2 foot per year. Five years after cutting, seedling and sapling height growth had accelerated to about 0.5 to 0.8...

Height-diameter equations for young-growth red fir in California and southern Oregon

Treesearch

K. Leroy Dolph

1989-01-01

Total tree height of young-growth red fir can be estimated from the relation of total tree height to diameter outside bark at breast height (DOB). Total tree heights and corresponding diameters were obtained from stem analyses of 562 trees distributed across 56 sampling locations in the true fir forest type of California and Oregon. The resulting equations can predict...

Deterioration of beetle-killed Douglas-fir in Oregon and Washington: a summary of findings to date.

Treesearch

Ernest Wright; K.H. Wright

1954-01-01

In 1952 and 1953 cooperative research was conducted by the Pacific Northwest Forest Experiment Station and the Research Department of Weyerhaeuser Timber Company to obtain information concerning the rate of deterioration of beetle-killed Douglas-fir. The study was prompted by an outbreak of the Douglas-fir beetle that developed in 1951 and has since killed an estimated...

Assessing post-fire Douglas-fir mortality and Douglas-fir beetle attacks in the northern Rocky Mountains

Treesearch

Sharon Hood; Barbara Bentz; Ken Gibson; Kevin Ryan; Gregg DeNitto

2007-01-01

Douglas-fir has life history traits that greatly enhance resistance to injury from fire, thereby increasing post-fire survival rates. Tools for predicting the probability of tree mortality following fire are important components of both pre-fire planning and post-fire management efforts. Using data from mixed-severity wildfire in Montana and Wyoming, Hood and Bentz (...

Release of Oregon white oak from overtopping Douglas-fir: effects on soil water and microclimate.

Treesearch

W.D. Devine; C.A. Harrington

2007-01-01

Many former Oregon white oak woodland and savanna stands in the coastal Pacific Northwest have been invaded and subsequently overtopped by Douglas-fir during the past century. We examined soil water and microclimate conditions near overtopped oak trees and near oak trees that had been released from Douglas-fir. In each of the three study years, volumetric soil water...

Population buildup and vertical spread of dwarf mistletoe on young red and white firs in California

Treesearch

Robert F. Scharpf; John R. Parmeter Jr.

1976-01-01

Rate of population buildup of dwarf mistletoe, Arceuthobium abietinum Engelm. ex Munz., was slow in most small red firs and white firs 12 to 15 years after inoculation with the parasite. Where population buildup did occur, it remained clustered in the lower portions of tree crowns near inoculation sites. Maximum distance of vertical spread was 16...

Douglas-fir ectomycorrhizae in 40- and 400-year-old stands: mycobiont availability to late successional western hemlock.

Treesearch

T. R. Horton; R. Molina; K. Hood

2005-01-01

We investigated ectomycorrhizal (EM) fungi in forest stands containing both early successional Douglas-fir and late successional western hemlock at two points in the typical stand development by identifying EM fungi from roots of Douglas-fir and western hemlock in mixed stands. Tn an early seral stage forest, EM roots of western hemlock seedlings and intermingling 40-...

Gross yield and mortality tables for fully stocked stands of Douglas-fir.

Treesearch

George R. Staebler

1955-01-01

Increasing interest in the practice of intensive forestry has demonstrated the need for gross yield tables for Douglas-fir showing the volume of trees that die as well as volume of live trees. Net yield tables for Douglas-fir, published in 1930, give the live volume in fully stocked stands at different ages on different sites. As in all normal yield tables, no...

Lumber grades from young-growth Douglas-fir.

Treesearch

E.E. Matson

1952-01-01

Young Douglas-fir timber is known to produce much No. 1 Common and Better lumber but, little or no clear lumber. The volume of lumber produced from young-growth timber has become a sizable part of the cut from the Douglas-fir region of Oregon and Washington. No exact figures are available, but it is estimated that more than one-fourth of the lumber produced from this...

Estimating decay in 40- to 90-year-old grand fir stands in the Clearwater region of northern Idaho.

Treesearch

Gregory M. Filip; John W. Schwandt; Susan K. Hagle

1990-01-01

The fir decay equation for Oregon and Washington was used to predict stem decay in 12 grand fir (Abies grandis (Dougl. ex D. Don) Lindl.) stands in the Clearwater region of northern Idaho. These 12 stands represented a range in geographic and stand characteristic variation. All 12 observed decay percentages were within their associated 95-percent...

Pityophthorus orarius Bright (Coleoptera: Scolytidae) in a northern California Douglas-fir seed orchard: effect of clone, tree vigor, and cone crop on rate of attack

Treesearch

Nancy G. Rappaport; David L. Wood

1994-01-01

The geographic range of the Douglas-fir twig beetle, Pityophthorus orarius Bright, was extended beyond the original provenance of southern British Columbia to northern California. A survey of 457 Douglas-fir [Pseudotsuga menziesii (Mirb.) Franco] trees in 1985 revealed that those with heavy cone crops were more likely to be...

Detecting changes in tree health and productivity in silver fir-beech forests of Slovenia

Treesearch

N. Torelli; W.C. Shortle; K. Cufar; F. Ferlin; K.T. Smith

1999-01-01

Cambial electrical resistance (CER) was used as an objective measure of vitality of silver fir (Abies alba) in the forests of Slovenia. Trees were rated during the growing season by CER and a subjective crown status index (CSI). Both CER and CSI were inversely correlated to annual ring width increment. Using both CER and CSI, fir were assigned to...

The Far-Infrared Luminosity Function and Star Formation Rate Density for Dust Obscured Galaxies in the Bootes Field

NASA Astrophysics Data System (ADS)

Calanog, Jae Alyson; Wardlow, J. L.; Fu, H.; Cooray, A. R.; HerMES

2013-01-01

We present the far-Infrared (FIR) luminosity function (LF) and the star-formation rate density (SFRD) for dust-obscured galaxies (DOGs) in the Bootes field at redshift 2. These galaxies are selected by having a large rest frame mid-IR to UV flux density ratio ( > 1000) and are expected to be some of the most luminous and heavily obscured galaxies in the Universe at this epoch. Photometric redshifts for DOGs are estimated from optical and mid-IR data using empirically derived low resolution spectral templates for AGN and galaxies. We use HerMES Herschel-SPIRE data to fit a modified blackbody to calculate the FIR luminosity (LFIR) and dust temperature (Td) for all DOGs individually detected in SPIRE maps. A stacking analyses was implemented to measure a median sub-mm flux of undetected DOGs. We find that DOGs have LIR and Td that are similar with the sub-millimeter galaxy (SMG) population, suggesting these two populations are related. The DOG LF and SFRD at 2 are calculated and compared to SMGs.

Multiscale segmentation-aided digital image correlation for strain concentration characterization of a turbine blade fir-tree root

NASA Astrophysics Data System (ADS)

Sun, Chen; Zhou, Yihao; Li, Yang; Chen, Jubing; Miao, Hong

2018-04-01

In this paper, a multiscale segmentation-aided digital image correlation method is proposed to characterize the strain concentration of a turbine blade fir-tree root during its contact with the disk groove. A multiscale approach is implemented to increase the local spatial resolution, as the strain concentration area undergoes highly non-uniform deformation and its size is much smaller than the contact elements. In this approach, a far-field view and several near-field views are selected, aiming to get the full-field deformation and local deformation simultaneously. To avoid the interference of different cameras, only the optical axis of the far-field camera is selected to be perpendicular to the specimen surface while the others are inclined. A homography transformation is optimized by matching the feature points, to rectify the artificial deformation caused by the inclination of the optical axis. The resultant genuine near-field strain is thus obtained after the transformation. A real-world experiment is carried out and the strain concentration is characterized. The strain concentration factor is defined accordingly to provide a quantitative analysis.

Hydraulic architecture and photosynthetic capacity as constraints on release from suppression in Douglas-fir and western hemlock.

PubMed

Renninger, Heidi J; Meinzer, Frederick C; Gartner, Barbara L

2007-01-01

We compared hydraulic architecture, photosynthesis and growth in Douglas-fir (Pseudotsuga menziesii (Mirb.) Franco), a shade-intolerant species, and western hemlock (Tsuga heterophylla (Raf.) Sarg.), a shade-tolerant species, to study the temporal pattern of release from suppressive shade. In particular, we sought to determine whether hydraulic architecture or photosynthetic capacity is most important in constraining release. The study was conducted at two sites with mixed stands of 10- to 20-year-old Douglas-fir and western hemlock. At one site, the stand had been thinned allowing release of the understory trees, whereas at the other site, the stand remained unthinned. Douglas-fir had lower height growth (from 1998-2003) and lower relative height growth (height growth from 1998 to 2003/height in 1998) than western hemlock. However, relative height growth of released versus suppressed trees was higher in Douglas-fir (130%) than in western hemlock (65%), indicating that, although absolute height growth was less, Douglas-fir did release from suppression. Release seemed to be constrained initially by a limited photosynthetic capacity in both species. Five years after release, Douglas-fir trees had 14 times the leaf area and 1.5 times the leaf nitrogen concentration (N (area)) of suppressed trees. Needles of released western hemlock trees had about twice the maximum assimilation rate (A (max)) at ambient [CO(2)] as needles of suppressed trees and exhibited no photoinhibition at the highest irradiances. After release, trees increased in leaf area, leaf N concentration and overall photosynthetic capacity. Subsequently, hydraulic architecture appeared to constrain release in Douglas-fir and, to a lesser extent, in western hemlock. Released trees had significantly less negative foliar delta(13)C values than suppressed trees and showed a positive relationship between leaf area:sapwood area ratio (A (L)/A (S)) and delta(13)C, suggesting that trees with more leaf area for a given sapwood area experienced a stomatal limitation on carbon gain. Nonetheless, these changes had no significant effects on leaf specific conductivities of suppressed versus released trees of either species, but leaf specific root conductance was significantly lower in released Douglas-fir.

Improving the retrieval rate of inferior vena cava filters with a multidisciplinary team approach

PubMed Central

Inagaki, Elica; Farber, Alik; Eslami, Mohammad H.; Siracuse, Jeffrey J.; Rybin, Denis V.; Sarosiek, Shayna; Sloan, J. Mark; Kalish, Jeffrey

2017-01-01

Objective The option to retrieve inferior vena cava (IVC) filters has resulted in an increase in the utilization of these devices as stopgap measures in patients with relative contraindications to anticoagulation. These retrievable IVC filters, however, are often not retrieved and become permanent. Recent data from our institution confirmed a historically low retrieval rate. Therefore, we hypothesized that the implementation of a new IVC filter retrieval protocol would increase the retrieval rate of appropriate IVC filters at our institution. Methods All consecutive patients who underwent an IVC filter placement at our institution between September 2003 and July 2012 were retrospectively reviewed. In August 2012, a multidisciplinary task force was established, and a new IVC filter retrieval protocol was implemented. Prospective data were collected using a centralized interdepartmental IVC filter registry for all consecutive patients who underwent an IVC filter placement between August 2012 and September 2014. Patients were chronologically categorized into preimplementation (PRE) and postimplementation (POST) groups. Comparisons of outcome measures, including the retrieval rate of IVC filters along with rates of retrieval attempt and technical failure, were made between the two groups. Results In the PRE and POST groups, a total of 720 and 74 retrievable IVC filters were implanted, respectively. In the POST group, 40 of 74 filters (54%) were successfully retrieved compared with 82 of 720 filters (11%) in the PRE group (P < .001). Furthermore, a greater number of IVC filter retrievals were attempted in the POST group than in the PRE group (66% vs 14%; P < .001). No significant difference was observed between the PRE and POST groups for technical failure (17% vs 18%; P = .9). Conclusions The retrieval rate of retrievable IVC filters at our institution was significantly increased with the implementation of a new IVC filter retrieval protocol with a multidisciplinary team approach. This improved retrieval rate is possible with minimal dedication of resources and can potentially lead to a decrease in IVC filter-related complications in the future. PMID:27318045

A model of head-related transfer functions based on a state-space analysis

NASA Astrophysics Data System (ADS)

Adams, Norman Herkamp

This dissertation develops and validates a novel state-space method for binaural auditory display. Binaural displays seek to immerse a listener in a 3D virtual auditory scene with a pair of headphones. The challenge for any binaural display is to compute the two signals to supply to the headphones. The present work considers a general framework capable of synthesizing a wide variety of auditory scenes. The framework models collections of head-related transfer functions (HRTFs) simultaneously. This framework improves the flexibility of contemporary displays, but it also compounds the steep computational cost of the display. The cost is reduced dramatically by formulating the collection of HRTFs in the state-space and employing order-reduction techniques to design efficient approximants. Order-reduction techniques based on the Hankel-operator are found to yield accurate low-cost approximants. However, the inter-aural time difference (ITD) of the HRTFs degrades the time-domain response of the approximants. Fortunately, this problem can be circumvented by employing a state-space architecture that allows the ITD to be modeled outside of the state-space. Accordingly, three state-space architectures are considered. Overall, a multiple-input, single-output (MISO) architecture yields the best compromise between performance and flexibility. The state-space approximants are evaluated both empirically and psychoacoustically. An array of truncated FIR filters is used as a pragmatic reference system for comparison. For a fixed cost bound, the state-space systems yield lower approximation error than FIR arrays for D>10, where D is the number of directions in the HRTF collection. A series of headphone listening tests are also performed to validate the state-space approach, and to estimate the minimum order N of indiscriminable approximants. For D = 50, the state-space systems yield order thresholds less than half those of the FIR arrays. Depending upon the stimulus uncertainty, a minimum state-space order of 7≤N≤23 appears to be adequate. In conclusion, the proposed state-space method enables a more flexible and immersive binaural display with low computational cost.

Far-infrared observations of the evolved H II region M16

NASA Technical Reports Server (NTRS)

Mcbreen, B.; Fazio, G. G.; Jaffe, D. T.

1982-01-01

The results of far infrared (FIR) observations of the larger H II region M16, associated with the young open star cluster NGC 6611, are discussed. Three FIR sources detected on an extended ridge of FIR emission within the scanned region are described. The observations confirm that M16 is an H II region in a late stage of evolution. The H II region has expanded and is now extremely density bounded, consisting of an extended region of ionized gas and a series of ionization fronts located at the surrounding molecular cloud boundaries nearest to the exciting OB star cluster. The FIR radiation arises from heated dust at these boundaries.

SPONGY (SPam ONtoloGY): Email Classification Using Two-Level Dynamic Ontology

PubMed Central

2014-01-01

Email is one of common communication methods between people on the Internet. However, the increase of email misuse/abuse has resulted in an increasing volume of spam emails over recent years. An experimental system has been designed and implemented with the hypothesis that this method would outperform existing techniques, and the experimental results showed that indeed the proposed ontology-based approach improves spam filtering accuracy significantly. In this paper, two levels of ontology spam filters were implemented: a first level global ontology filter and a second level user-customized ontology filter. The use of the global ontology filter showed about 91% of spam filtered, which is comparable with other methods. The user-customized ontology filter was created based on the specific user's background as well as the filtering mechanism used in the global ontology filter creation. The main contributions of the paper are (1) to introduce an ontology-based multilevel filtering technique that uses both a global ontology and an individual filter for each user to increase spam filtering accuracy and (2) to create a spam filter in the form of ontology, which is user-customized, scalable, and modularized, so that it can be embedded to many other systems for better performance. PMID:25254240

Design of coupled mace filters for optical pattern recognition using practical spatial light modulators

NASA Technical Reports Server (NTRS)

Rajan, P. K.; Khan, Ajmal

1993-01-01

Spatial light modulators (SLMs) are being used in correlation-based optical pattern recognition systems to implement the Fourier domain filters. Currently available SLMs have certain limitations with respect to the realizability of these filters. Therefore, it is necessary to incorporate the SLM constraints in the design of the filters. The design of a SLM-constrained minimum average correlation energy (SLM-MACE) filter using the simulated annealing-based optimization technique was investigated. The SLM-MACE filter was synthesized for three different types of constraints. The performance of the filter was evaluated in terms of its recognition (discrimination) capabilities using computer simulations. The correlation plane characteristics of the SLM-MACE filter were found to be reasonably good. The SLM-MACE filter yielded far better results than the analytical MACE filter implemented on practical SLMs using the constrained magnitude technique. Further, the filter performance was evaluated in the presence of noise in the input test images. This work demonstrated the need to include the SLM constraints in the filter design. Finally, a method is suggested to reduce the computation time required for the synthesis of the SLM-MACE filter.

SPONGY (SPam ONtoloGY): email classification using two-level dynamic ontology.

PubMed

Youn, Seongwook

2014-01-01

Email is one of common communication methods between people on the Internet. However, the increase of email misuse/abuse has resulted in an increasing volume of spam emails over recent years. An experimental system has been designed and implemented with the hypothesis that this method would outperform existing techniques, and the experimental results showed that indeed the proposed ontology-based approach improves spam filtering accuracy significantly. In this paper, two levels of ontology spam filters were implemented: a first level global ontology filter and a second level user-customized ontology filter. The use of the global ontology filter showed about 91% of spam filtered, which is comparable with other methods. The user-customized ontology filter was created based on the specific user's background as well as the filtering mechanism used in the global ontology filter creation. The main contributions of the paper are (1) to introduce an ontology-based multilevel filtering technique that uses both a global ontology and an individual filter for each user to increase spam filtering accuracy and (2) to create a spam filter in the form of ontology, which is user-customized, scalable, and modularized, so that it can be embedded to many other systems for better performance.

Reconfigurable Analog PDE computation for Baseband and RFComputation

DTIC Science & Technology

2017-03-01

waveguiding PDEs. One-dimensional ladder topologies enable linear delays, linear-phase analog filters , as well as analog beamforming, potentially at RF...performance. This discussion focuses on ODE / PDE analog computation available in SoC FPAA structures. One such computation is a ladder filter (Fig...Implementation of a one-dimensional ladder filter for computing inductor (L) and capacitor (C) lines. These components can be implemented in CABs or as

A Stabilized Sparse-Matrix U-D Square-Root Implementation of a Large-State Extended Kalman Filter

NASA Technical Reports Server (NTRS)

Boggs, D.; Ghil, M.; Keppenne, C.

1995-01-01

The full nonlinear Kalman filter sequential algorithm is, in theory, well-suited to the four-dimensional data assimilation problem in large-scale atmospheric and oceanic problems. However, it was later discovered that this algorithm can be very sensitive to computer roundoff, and that results may cease to be meaningful as time advances. Implementations of a modified Kalman filter are given.

A simple structure wavelet transform circuit employing function link neural networks and SI filters

NASA Astrophysics Data System (ADS)

Mu, Li; Yigang, He

2016-12-01

Signal processing by means of analog circuits offers advantages from a power consumption viewpoint. Implementing wavelet transform (WT) using analog circuits is of great interest when low-power consumption becomes an important issue. In this article, a novel simple structure WT circuit in analog domain is presented by employing functional link neural network (FLNN) and switched-current (SI) filters. First, the wavelet base is approximated using FLNN algorithms for giving a filter transfer function that is suitable for simple structure WT circuit implementation. Next, the WT circuit is constructed with the wavelet filter bank, whose impulse response is the approximated wavelet and its dilations. The filter design that follows is based on a follow-the-leader feedback (FLF) structure with multiple output bilinear SI integrators and current mirrors as the main building blocks. SI filter is well suited for this application since the dilation constant across different scales of the transform can be precisely implemented and controlled by the clock frequency of the circuit with the same system architecture. Finally, to illustrate the design procedure, a seventh-order FLNN-approximated Gaussian wavelet is implemented as an example. Simulations have successfully verified that the designed simple structure WT circuit has low sensitivity, low-power consumption and litter effect to the imperfections.

The correlation between far-IR and radio continuum emission from spiral galaxies

NASA Technical Reports Server (NTRS)

Dickey, John M.; Garwood, Robert W.; Helou, George

1987-01-01

A sample of 30 galaxies selected for their intense IRAS flux at 60 and 100 micron using the Arecibo telescope at 21 cm to measure the continuum and HI line luminosities were observed. The centimeter wave continuum correlates very well with the far-infrared flux, with a correlation coefficient as high as that found for other samples, and the same ratio between FIR and radio luminosities. Weaker correlations are seen between the FIR and optical luminosity and between the FIR and radio continuum. There is very little correlation between the FIR and the HI mass deduced from the integral of the 21 cm line. The strength of the radio continuum correlation suggests that there is little contribution to either the radio and FIR from physical processes not affecting both. If they each reflect time integrals of the star formation rate then the time constants must be similar, or the star formation rate must change slowly in these galaxies.

Processing Functional Near Infrared Spectroscopy Signal with a Kalman Filter to Assess Working Memory during Simulated Flight.

PubMed

Durantin, Gautier; Scannella, Sébastien; Gateau, Thibault; Delorme, Arnaud; Dehais, Frédéric

2015-01-01

Working memory (WM) is a key executive function for operating aircraft, especially when pilots have to recall series of air traffic control instructions. There is a need to implement tools to monitor WM as its limitation may jeopardize flight safety. An innovative way to address this issue is to adopt a Neuroergonomics approach that merges knowledge and methods from Human Factors, System Engineering, and Neuroscience. A challenge of great importance for Neuroergonomics is to implement efficient brain imaging techniques to measure the brain at work and to design Brain Computer Interfaces (BCI). We used functional near infrared spectroscopy as it has been already successfully tested to measure WM capacity in complex environment with air traffic controllers (ATC), pilots, or unmanned vehicle operators. However, the extraction of relevant features from the raw signal in ecological environment is still a critical issue due to the complexity of implementing real-time signal processing techniques without a priori knowledge. We proposed to implement the Kalman filtering approach, a signal processing technique that is efficient when the dynamics of the signal can be modeled. We based our approach on the Boynton model of hemodynamic response. We conducted a first experiment with nine participants involving a basic WM task to estimate the noise covariances of the Kalman filter. We then conducted a more ecological experiment in our flight simulator with 18 pilots who interacted with ATC instructions (two levels of difficulty). The data was processed with the same Kalman filter settings implemented in the first experiment. This filter was benchmarked with a classical pass-band IIR filter and a Moving Average Convergence Divergence (MACD) filter. Statistical analysis revealed that the Kalman filter was the most efficient to separate the two levels of load, by increasing the observed effect size in prefrontal areas involved in WM. In addition, the use of a Kalman filter increased the performance of the classification of WM levels based on brain signal. The results suggest that Kalman filter is a suitable approach for real-time improvement of near infrared spectroscopy signal in ecological situations and the development of BCI.

Processing Functional Near Infrared Spectroscopy Signal with a Kalman Filter to Assess Working Memory during Simulated Flight

PubMed Central

Durantin, Gautier; Scannella, Sébastien; Gateau, Thibault; Delorme, Arnaud; Dehais, Frédéric

2016-01-01

Working memory (WM) is a key executive function for operating aircraft, especially when pilots have to recall series of air traffic control instructions. There is a need to implement tools to monitor WM as its limitation may jeopardize flight safety. An innovative way to address this issue is to adopt a Neuroergonomics approach that merges knowledge and methods from Human Factors, System Engineering, and Neuroscience. A challenge of great importance for Neuroergonomics is to implement efficient brain imaging techniques to measure the brain at work and to design Brain Computer Interfaces (BCI). We used functional near infrared spectroscopy as it has been already successfully tested to measure WM capacity in complex environment with air traffic controllers (ATC), pilots, or unmanned vehicle operators. However, the extraction of relevant features from the raw signal in ecological environment is still a critical issue due to the complexity of implementing real-time signal processing techniques without a priori knowledge. We proposed to implement the Kalman filtering approach, a signal processing technique that is efficient when the dynamics of the signal can be modeled. We based our approach on the Boynton model of hemodynamic response. We conducted a first experiment with nine participants involving a basic WM task to estimate the noise covariances of the Kalman filter. We then conducted a more ecological experiment in our flight simulator with 18 pilots who interacted with ATC instructions (two levels of difficulty). The data was processed with the same Kalman filter settings implemented in the first experiment. This filter was benchmarked with a classical pass-band IIR filter and a Moving Average Convergence Divergence (MACD) filter. Statistical analysis revealed that the Kalman filter was the most efficient to separate the two levels of load, by increasing the observed effect size in prefrontal areas involved in WM. In addition, the use of a Kalman filter increased the performance of the classification of WM levels based on brain signal. The results suggest that Kalman filter is a suitable approach for real-time improvement of near infrared spectroscopy signal in ecological situations and the development of BCI. PMID:26834607

Early survival and growth of planted Douglas-fir with red alder in four mixed regimes.

Treesearch

Marshall D. Murray; Richard E. Miller

1986-01-01

To quantify between-species interactions, we measured and compared survival and growth of planted Douglas-fir and associated planted and volunteer red alder at a location on the west side of the Cascade Range in Washington. The planted alder were wildlings dug either from a nearby area or from a distant, coastal site and interplanted into a 3-year-old Douglas-fir...

Effects of manganese and manganese-nitrogen applications on growth and nutrition of Douglas-fir seedlings.

Treesearch

M. A. Radwan; John S. Shumway; Dean S. DeBell

1979-01-01

Effects of manganese (Mn) on Douglas-fir grown in soil, with and without urea, and in nutrient solution were investigated. In addition, Mn sorption by forest soils was evaluated. Results show that Douglas-fir does not respond to added Mn and is quite tolerant to high Mn levels. Moreover, Mn sorption by soils is high. It is doubtful that Mn toxicity is of practical...

Balsam fir conservation and red spruce ecosystem restoration initiatives in the West Virginia highlands

Treesearch

Corey A. Bonasso; David W. Saville

2010-01-01

The West Virginia Highlands Conservancy has been working for more than a decade to protect, conserve, and restore the spruce-fir forests in West Virginia. Beginning in the mid 1990s an effort was initiated to conserve balsam fir in West Virginia where it reaches its southern most extent in North America. This work led to further efforts which have focused on the...

Nonlinear equations for predictiing diameter inside bark at breast height for young-growth red fir in California and southern Oregon

Treesearch

K. Leroy Dolph

1989-01-01

Inside bark diameters of young-growth red fir can be estimated from the relationship of inside bark diameter 10 outside bark diameter at breast height. Inside and outside bark diameter were obtained from stem analyses of 562 trees distributed across 56 sampling locations in the true fir forest type of California and southern Oregon. The resulting equation can predict...

Repeated manual release in a young plantation: effect on Douglas-fir seedlings, hardwoods, shrubs, forbs, and grasses.

Treesearch

Philip M. McDonald; Gary O. Fiddler; Henry Harrison

1994-01-01

Douglas-fir seedlings on the Arcata Resource Area, Bureau of Land Management, U.S. Department of the Interior, in central coastal California, were released by chain sawing and grubbing competing vegetation around them at different frequencies (0, 2, and 3 grubbings) over a 5-year period. After 5 years, average Douglas-fir stem diameter (measured at 12 inches above mean...

Five-year growth responses of Douglas-fir, western hemlock, and western redcedar seedlings to manipulated levels of overstory and understory competition.

Treesearch

T.B. Harrington

2006-01-01

Douglas-fir, western hemlock, and western redcedar seedlings were planted in 2001 within clearcuts, shelterwoods, or thinned stands of second-growth Douglas-fir. Understory vegetation was left untreated or removed to provide areas of vegetation control (AVC) of 0, 50, or 100 percent of seedling growing space. Third-year stem volume of seedlings growing in clearcuts...

Fine-structure mapping of the firA gene, a locus involved in the phenotypic expression of rifampin resistance in Escherichia.

PubMed

Lathe, R

1977-09-01

The firA (Ts)200 mutation not only eliminates the resistance to rifampin of certain genetically resistant strains, but, moreover, renders ribonucleic acid synthesis thermolabile. The firA gene has been mapped by P1 tranduction and is located extremely close to the structural gene for deoxyribonucleic acid polymerase III at 4 min on the Escherichia coli linkage map.

Radial growth in grand fir and Douglas-fir related to defoliation by the Douglas-fir tussock moth in the Blue Mountains outbreak.

Treesearch

B.E. Wickman; D.L. Henshaw; S.K. Gollob

1980-01-01

Radial growth reduction related to amount of tree defoliation was studied following a severe tussock moth outbreak. Growth sharply declined the year after defoliation began, and amount of decline was proportional to percent defoliation. Growth recovery began the year after defoliation ceased and radial increment had returned to pre-outbreak levels 5 years after...

Mulching to regenerate a harsh site: effect on Douglas-fir seedlings, forbs, grasses, and ferns

Treesearch

Philip M. McDonald; Gary O. Fiddler; Henry R. Harrison

1994-01-01

Douglas-fir seedlings on the Arcata District, Bureau of Land Management, U.S. Department of the Interior, in central coastal California, were planted in an effort to restore the natural forest to what was then pastureland. Douglas-fir seedlings were released from a complex forb-grass-fern plant community by applying very large (10-ft square) and very small (2-foot...

Comparative drought resistance of five conifers and foliage moisture content as a viability index.

Treesearch

Richard P. Pharis

1966-01-01

Whole plant lethal points of foliage moisture content (FMC) for ponderosa pine, sugar pine, Douglas-fir, grand fir, and incense-cedar were established from foliage tissue of various ages. Exact lethal level depended upon the age of the tissue, but there was a general plateau between the ages 6 and 13 months for sugar pine and Douglas-fir and 3 and 13 months for incense...

Tree shaking machine aids cone collection in a Douglas-fir seed orchard.

Treesearch

Donald L. Copes; William K. Randall

1983-01-01

A boom-type tree shaker was used in a Douglas-fir seed orchard to remove cones from 7- to 9-meter tall grafted Douglas-fir trees. An average of 55 percent of the cones were removed by shaking, while damage inflicted to the upper crown was confined primarily to branch and leader breakage in the top three internodes. Damage to the lower bole, where the shaker head...

[A comparative study on soil fauna in native secondary evergreen broad-leaved forest and Chinese fir plantation forests in subtropics].

PubMed

Yan, Shaokui; Wang, Silong; Hu, Yalin; Gao, Hong; Zhang, Xiuyong

2004-10-01

In this study, we investigated the response of soil animal communities to the replacement of native secondary forest by Chinese fir plantation forest and successive rotation of Chinese fir in subtropics. Three adjacent forest stands, i.e., native secondary evergreen broad-leaved forest stand (control) and Chinese fir plantation stands of first (20 yr) and second (20 yr) rotations were selected for the comparison of soil fauna. All animals were extracted from the floor litter and 0-15 cm soil layer of the stands in Summer, 2003 by using Tullgren method, wet funnel method and hand-sorting method. Compared to two Chinese fir plantation forests, the native secondary evergreen broad-leaved forest had a higher abundance and a higher taxonomic diversity of animals in soil and litter, but there were no significant differences in the biomass and productivity of soil fauna between all study stands. The abundance or diversity did not differ significantly between the first rotation and second rotation stands, too. The results supported that vegetation cover might be one of the main forces driving the development of soil animal communities, and the effect of successive rotation of Chinese fir on the development of soil fauna was a slow-running process.

Source identification of western Oregon Douglas-fir wood cores using mass spectrometry and random forest classification1

PubMed Central

Finch, Kristen; Espinoza, Edgard; Jones, F. Andrew; Cronn, Richard

2017-01-01

Premise of the study: We investigated whether wood metabolite profiles from direct analysis in real time (time-of-flight) mass spectrometry (DART-TOFMS) could be used to determine the geographic origin of Douglas-fir wood cores originating from two regions in western Oregon, USA. Methods: Three annual ring mass spectra were obtained from 188 adult Douglas-fir trees, and these were analyzed using random forest models to determine whether samples could be classified to geographic origin, growth year, or growth year and geographic origin. Specific wood molecules that contributed to geographic discrimination were identified. Results: Douglas-fir mass spectra could be differentiated into two geographic classes with an accuracy between 70% and 76%. Classification models could not accurately classify sample mass spectra based on growth year. Thirty-two molecules were identified as key for classifying western Oregon Douglas-fir wood cores to geographic origin. Discussion: DART-TOFMS is capable of detecting minute but regionally informative differences in wood molecules over a small geographic scale, and these differences made it possible to predict the geographic origin of Douglas-fir wood with moderate accuracy. Studies involving DART-TOFMS, alone and in combination with other technologies, will be relevant for identifying the geographic origin of illegally harvested wood. PMID:28529831

Soil spore bank communities of ectomycorrhizal fungi in endangered Chinese Douglas-fir forests.

PubMed

Wen, Zhugui; Shi, Liang; Tang, Yangze; Hong, Lizhou; Xue, Jiawang; Xing, Jincheng; Chen, Yahua; Nara, Kazuhide

2018-01-01

Chinese Douglas-fir (Pseudotsuga sinensis) is an endangered Pinaceae species found in several isolated regions of China. Although soil spore banks of ectomycorrhizal (ECM) fungi can play an important role in seedling establishment after disturbance, such as in the well-known North American relative (Pseudotsuga menziesii), we have no information about soil spore bank communities in relict forests of Chinese Douglas-fir. We conducted bioassays of 73 soil samples collected from three Chinese Douglas-fir forests, using North American Douglas-fir as bait seedlings, and identified 19 species of ECM fungi. The observed spore bank communities were significantly different from those found in ECM fungi on the roots of resident trees at the same sites (p = 0.02). The levels of potassium (K), nitrogen (N), organic matter, and the pH of soil were the dominant factors shaping spore bank community structure. A new Rhizopogon species was the most dominant species in the spore banks. Specifically, at a site on Sanqing Mountain, 22 of the 57 surviving bioassay seedlings (representing 21 of the 23 soil samples) were colonized by this species. ECM fungal richness significantly affected the growth of bioassay seedlings (R 2  = 0.20, p = 0.007). Growth was significantly improved in seedlings colonized by Rhizopogon or Meliniomyces species compared with uncolonized seedlings. Considering its specificity to Chinese Douglas-fir, predominance in the soil spore banks, and positive effect on host growth, this new Rhizopogon species could play critical roles in seedling establishment and forest regeneration of endangered Chinese Douglas-fir.

Reproductive potential of balsam fir (Abies balsamea), white spruce (Picea glauca), and black spruce (P. mariana) at the ecotone between mixedwood and coniferous forests in the boreal zone of western Quebec.

PubMed

Messaoud, Yassine; Bergeron, Yves; Asselin, Hugo

2007-05-01

The reproductive potentials of balsam fir and white spruce (co-dominants in mixedwood forests) and black spruce (dominant in coniferous forests) were studied to explain the location of the ecotone between the two forest types in the boreal zone of Quebec. Four sites were selected along a latitudinal gradient crossing the ecotone. Cone crop, number of seeds per cone, percentage filled seeds, and percentage germination were measured for each species. Balsam fir and white spruce cone crops were significantly lower in the coniferous than in the mixedwood forest, while black spruce had greater crop constancy and regularity between both forest types. Mast years were more frequent for black spruce than for balsam fir in both forest types (mast year data not available for white spruce). The number of seeds per cone was more related to cone size than to forest type for all species. Black spruce produced more filled seeds in the coniferous forest than balsam fir or white spruce. The sum of growing degree-days and the maximum temperature of the warmest month (both for the year prior to cone production) significantly affected balsam fir cone production. The climate-related northward decrease in reproductive potential of balsam fir and white spruce could partly explain the position of the northern limit of the mixedwood forest. This could change drastically, however, as the ongoing climate warming might cancel this competitive advantage of black spruce.

Spatial correlations between browsing on balsam fir by white-tailed deer and the nutritional value of neighboring winter forage.

PubMed

Champagne, Emilie; Moore, Ben D; Côté, Steeve D; Tremblay, Jean-Pierre

2018-03-01

Associational effects, that is, the influence of neighboring plants on herbivory suffered by a plant, are an outcome of forage selection. Although forage selection is a hierarchical process, few studies have investigated associational effects at multiple spatial scales. Because the nutritional quality of plants can be spatially structured, it might differently influence associational effects across multiple scales. Our objective was to determine the radius of influence of neighbor density and nutritional quality on balsam fir ( Abies balsamea ) herbivory by white-tailed deer ( Odocoileus virginianus ) in winter. We quantified browsing rates on fir and the density and quality of neighboring trees in a series of 10-year-old cutovers on Anticosti Island (Canada). We used cross-correlations to investigate relationships between browsing rates and the density and nutritional quality of neighboring trees at distances up to 1,000 m. Balsam fir and white spruce ( Picea glauca ) fiber content and dry matter in vitro true digestibility were correlated with fir browsing rate at the finest extra-patch scale (across distance of up to 50 m) and between cutover areas (300-400 m). These correlations suggest associational effects, that is, low nutritional quality of neighbors reduces the likelihood of fir herbivory (associational defense). Our results may indicate associational effects mediated by intraspecific variation in plant quality and suggest that these effects could occur at scales from tens to hundreds of meters. Understanding associational effects could inform strategies for restoration or conservation; for example, planting of fir among existing natural regeneration could be concentrated in areas of low nutritional quality.

Added value of far-infrared radiometry for remote sensing of ice clouds

NASA Astrophysics Data System (ADS)

Libois, Quentin; Blanchet, Jean-Pierre

2017-06-01

Several cloud retrieval algorithms based on satellite observations in the infrared have been developed in the last decades. However, these observations only cover the midinfrared (MIR, λ < 15 μm) part of the spectrum, and none are available in the far-infrared (FIR, λ≥ 15 μm). Using the optimal estimation method, we show that adding a few FIR channels to existing spaceborne radiometers would significantly improve their ability to retrieve ice cloud radiative properties. For clouds encountered in the polar regions and the upper troposphere, where the atmosphere is sufficiently transparent in the FIR, using FIR channels would reduce by more than 50% the uncertainties on retrieved values of optical thickness, effective particle diameter, and cloud top altitude. Notably, this would extend the range of applicability of current retrieval methods to the polar regions and to clouds with large optical thickness, where MIR algorithms perform poorly. The high performance of solar reflection-based algorithms would thus be reached in nighttime conditions. Since the sensitivity of ice cloud thermal emission to effective particle diameter is approximately 5 times larger in the FIR than in the MIR, using FIR observations is a promising venue for studying ice cloud microphysics and precipitation processes. This is highly relevant for cirrus clouds and convective towers. This is also essential to study precipitation in the driest regions of the atmosphere, where strong feedbacks are at play between clouds and water vapor. The deployment in the near future of a FIR spaceborne radiometer is technologically feasible and should be strongly supported.

Syntheses, crystal structures and fluorescent properties of three metal- tris(4‧-carboxybiphenyl)amine frameworks

NASA Astrophysics Data System (ADS)

Yuan, Lv-Bing; He, Yan-Ping; Xu, Hai; Zhang, Jian

2017-11-01

Triphenylamine and its derivatives have been widely concerned because of their excellent performance in the area of the photoelectric functional material. In this work, we chose a nanosized tris(4‧-carboxybiphenyl)amine (H3TPA) as organic ligand. By employing the H3TPA ligand to assemble with M2+ (M = Zn, Cd, and Pb) ions, respectively, three metal-organic frameworks (FIR-43 to FIR-45, FIR denotes Fujian Institute of Research) have been synthesized under different solvent systems. FIR-43 exhibits a 3-connected two-dimensional (2D) network based on mononuclear [Zn(COO)3] second building unit (SBU). Unlike the anionic framework FIR-43, FIR-44 is a neutral 2D layer constructed by trinuclear [Cd3(COO)6] SBU and displays a (3,6)-NbSe2 topology structure. If the weak Pb-O interactions in the range of 2.79-2.88 Å are considered, FIR-45 is a neutral 3D framework built by hexanuclear [Pb6(DMAE)6(COO)6] SBU (DMAE = N,N-dimethylethanolamine) and represents a (3,6)-connected (4·82)2(42·811·102) topology. Thermogravimetric analyses (TGA) and X-ray powder diffraction (PXRD) patterns were used to evaluate their thermal stability and phase purity. Photoluminescence studies showed that they exhibited strong emitting bands in the visible region with high quantum yields and long luminescent lifetimes. The assembly between nanosized tris((4-carboxyl)phenylduryl)amine ligand and M2+ (M = Zn, Cd, and Pb) ions leads to three new metal-organic frameworks, which show excellent fluorescent properties.