[Ultrahigh dose-rate, "flash" irradiation minimizes the side-effects of radiotherapy].

PubMed

Favaudon, V; Fouillade, C; Vozenin, M-C

2015-10-01

Pencil beam scanning and filter free techniques may involve dose-rates considerably higher than those used in conventional external-beam radiotherapy. Our purpose was to investigate normal tissue and tumour responses in vivo to short pulses of radiation. C57BL/6J mice were exposed to bilateral thorax irradiation using pulsed (at least 40 Gy/s, flash) or conventional dose-rate irradiation (0.03 Gy/s or less) in single dose. Immunohistochemical and histological methods were used to compare early radio-induced apoptosis and the development of lung fibrosis in the two situations. The response of two human (HBCx-12A, HEp-2) tumour xenografts in nude mice and one syngeneic, orthotopic lung carcinoma in C57BL/6J mice (TC-1 Luc+), was monitored in both radiation modes. A 17 Gy conventional irradiation induced pulmonary fibrosis and activation of the TGF-beta cascade in 100% of the animals 24-36 weeks post-treatment, as expected, whereas no animal developed complications below 23 Gy flash irradiation, and a 30 Gy flash irradiation was required to induce the same extent of fibrosis as 17 Gy conventional irradiation. Cutaneous lesions were also reduced in severity. Flash irradiation protected vascular and bronchial smooth muscle cells as well as epithelial cells of bronchi against acute apoptosis as shown by analysis of caspase-3 activation and TUNEL staining. In contrast, the antitumour effectiveness of flash irradiation was maintained and not different from that of conventional irradiation. Flash irradiation shifted by a large factor the threshold dose required to initiate lung fibrosis without loss of the antitumour efficiency, suggesting that the method might be used to advantage to minimize the complications of radiotherapy. Copyright © 2015 Société française de radiothérapie oncologique (SFRO). Published by Elsevier SAS. All rights reserved.

Enhanced radioactivity due to natural oil and gas production and related radiological problems.

PubMed

Kolb, W A; Wojcik, M

1985-10-01

Increased gamma radiation detected incidentally a few years ago in a North German oil field was traceable to radioactive scale. At the request of the Federal Ministry of the Interior a survey program was then established for dose rate measurements at various production sites, assessment of the radionuclide content of brines and scale and the Rn-222 content of natural gas. Dose equivalent rates of up to 50 mu Sv/h have been measured at the external surface of storage tanks for brines, but 73% of the 160 sites investigated did not show an increase above the natural background. Brines from gas fields contained Ra-226 of up to 286 Bq/l and scale of up to 1 kBq/g. In brines and scale from oil fields Ra-228 was usually the predominant radionuclide. Some samples contained "unsupported" Pb-210 and even Ac-227, too, but practically no uranium or thorium. The Rn-222 concentrations in natural gas samples varied between 0.004 and 4 Bq/l with a mean value of 0.6 Bq/l. It is shown that the radiation exposure due to natural gas consumption is negligible but some other problems or radiological relevance are recognized.

Informing hot flash treatment decisions for breast cancer survivors: a systematic review of randomized trials comparing active interventions.

PubMed

Johns, Claire; Seav, Susan M; Dominick, Sally A; Gorman, Jessica R; Li, Hongying; Natarajan, Loki; Mao, Jun James; Irene Su, H

2016-04-01

Patient-centered decision making about hot flash treatments often incorporates a balance of efficacy and side effects in addition to patient preference. This systematic review examines randomized controlled trials (RCTs) comparing at least two non-hormonal hot flash treatments in breast cancer survivors. In July 2015, PubMed, SCOPUS, CINAHL, Cochrane, and Web of Science databases were searched for RCTs comparing active, non-hormonal hot flash treatments in female breast cancer survivors. Thirteen trials were included after identifying 906 potential studies. Four trials were dose comparison studies of pharmacologic treatments citalopram, venlafaxine, gabapentin, and paroxetine. Hot flash reduction did not differ by tamoxifen or aromatase inhibitor use. Citalopram 10, 20, and 30 mg daily had comparable outcomes. Venlafaxine 75 mg daily improved hot flashes without additional side effects from higher dosing. Gabapentin 900 mg daily improved hot flashes more than 300 mg. Paroxetine 10 mg daily had fewer side effects than 20 mg. Among four trials comparing different pharmacologic treatments, venlafaxine alleviated hot flash symptoms faster than clonidine; participants preferred venlafaxine over gabapentin. Five trials compared pharmacologic to non-pharmacologic treatments. Acupuncture had similar efficacy to venlafaxine and gabapentin but may have longer durability after completing treatment and fewer side effects. We could not perform a pooled meta-analysis because outcomes were not reported in comparable formats. Clinical trial data on non-hormonal hot flash treatments provide comparisons of hot flash efficacy and other patient important outcomes to guide clinical management. Clinicians can use the information to help patients select hot flash interventions.

Generation and dose distribution measurement of flash x-ray in KALI-5000 system

DOE Office of Scientific and Technical Information (OSTI.GOV)

Menon, Rakhee; Roy, Amitava; Mitra, S.

2008-10-15

Flash x-ray generation studies have been carried out in KALI-5000 Pulse power system. The intense relativistic electron beam has been bombarded on a tantalum target at anode to produce flash x-ray via bremsstrahlung conversion. The typical electron beam parameter was 360 kV, 18 kA, and 100 ns, with a few hundreds of A/cm{sup 2} current density. The x-ray dose has been measured with calcium sulfate:dysposium (CaSO{sub 4}:Dy) thermoluminescent dosimeter and the axial dose distribution has been characterized. It has been observed that the on axis dose falls of with distance {approx}1/x{sup n}, where n varies from 1.8 to 1.85. Amore » maximum on axis dose of 46 mrad has been measured at 1 m distance from the source. A plastic scintillator with optical fiber coupled to a photomultiplier tube has been developed to measure the x-ray pulse width. The typical x-ray pulse width varied from 50 to 80 ns.« less

Toxicity study of Vernonia cinerea.

PubMed

Latha, L Yoga; Darah, I; Jain, K; Sasidharan, S

2010-01-01

The methanol extract of Vernonia cinerea Less (Asteraceae), which exhibited antimicrobial activity, was tested for toxicity. In an acute toxicity study using mice, the median lethal dose (LD(50)) of the extract was greater than 2000 mg/kg, and we found no pathological changes in macroscopic examination by necropsy of mice treated with extract. As well as the oral acute toxicity study, the brine shrimp lethality test was also done. Brine shrimp test LC(50) values were 3.87 mg/mL (6 h) and 2.72 mg/mL (24 h), exhibiting no significant toxicity result. In conclusion, the methanol extract of V. cinerea did not produce toxic effects in mice and brine shrimp.

Models for Total-Dose Radiation Effects in Non-Volatile Memory

DOE Office of Scientific and Technical Information (OSTI.GOV)

Campbell, Philip Montgomery; Wix, Steven D.

The objective of this work is to develop models to predict radiation effects in non- volatile memory: flash memory and ferroelectric RAM. In flash memory experiments have found that the internal high-voltage generators (charge pumps) are the most sensitive to radiation damage. Models are presented for radiation effects in charge pumps that demonstrate the experimental results. Floating gate models are developed for the memory cell in two types of flash memory devices by Intel and Samsung. These models utilize Fowler-Nordheim tunneling and hot electron injection to charge and erase the floating gate. Erase times are calculated from the models andmore » compared with experimental results for different radiation doses. FRAM is less sensitive to radiation than flash memory, but measurements show that above 100 Krad FRAM suffers from a large increase in leakage current. A model for this effect is developed which compares closely with the measurements.« less

SU-E-T-489: Incorporating Skin Flash Into VMAT WBI: Impacts On Surface Dosimetry

DOE Office of Scientific and Technical Information (OSTI.GOV)

Buele, A Bejarano; Tanny, S; Warrell, G

Purpose: Increased use of inverse planning limits the amount of skin flash in whole breast irradiation (WBI). Strategies to incorporate flash into inverse-planned treatments involve overriding air to the density of water or tissue. This introduces uncertainties to the superficial dose distribution, potentially degrading the coverage at the skin-bolus interface. We investigate the accuracy of various commonly used bolus materials to incorporate flash in VMAT WBI plans while minimizing the perturbation near the skin. Methods: We obtained a CT-simulation of an anthropomorphic phantom with a breast attachment. Three VMAT plans were created with different boluses: 1 cm of 1 g/cm{supmore » 3} bolus (Superflab), 1 cm of 0.65 g/cm{sup 3} bolus (wet towels), and 1 cm of g/cm{sup 3} bolus with 2 dose levels accounting for the difference between bolus and tissue density. The PTV was extended into the bolus, outside the patient body contour to incorporate flash. OSLDs were used to obtain surface doses at the medial, lateral and tip sites of the breast. Each plan was irradiated four times using CBCT for positioning and dosimeter localization. Results: The average thickness of the wet-towel bolus on delivery was 8 mm with a CBCT-measured density of 0.6 g/cm{sup 3}. OSLD measurements demonstrated good agreement with predicted doses from Pinnacle. Average deviations were −5.7%, −2.5%, and −2.6% for plans 1, 2, and 3, respectively. OSLDs placed at the medial and lateral portions of the breast showed the largest average deviations. The maximum recorded deviation from planned values was −8.6%. The largest dose fluctuations occurred near areas where the bolus failed to properly conform to the breast contour. Conclusion: Use of wet-towel bolus improved dose delivery accuracy compared to standard Superflab bolus. Areas of poor bolus conformity adversely affected dose delivery. We recommend the use of wet-towel bolus over Superflab bolus for VMAT WBI.« less

Corrosion tests in Hawaiian geothermal fluids

DOE Office of Scientific and Technical Information (OSTI.GOV)

Larsen-Basse, J.; Lam, Kam-Fai

1984-01-01

Exposure tests were conductd in binary geothermal brine on the island of Hawaii. The steam which flashes from the high pressure, high temperature water as it is brought to ambient pressure contains substantial amounts of H{sub 2}S. In the absence of oxygen this steam is only moderately aggressive but in the aerated state it is highly aggressive to carbon steels and copper alloys. The liquid after flasing is intermediately aggressive. The Hawaiian fluid is unique in chemistry and corrosion behavior; its corrosiveness is relatively mild for a geothermal fluid falling close to the Iceland-type resources. 24 refs., 7 figs., 5more » tabs.« less

Evaluation of 1.5-T Cell Flash Memory Total Ionizing Dose Response

NASA Astrophysics Data System (ADS)

Clark, Lawrence T.; Holbert, Keith E.; Adams, James W.; Navale, Harshad; Anderson, Blake C.

2015-12-01

Flash memory is an essential part of systems used in harsh environments, experienced by both terrestrial and aerospace TID applications. This paper presents studies of COTS flash memory TID hardness. While there is substantial literature on flash memory TID response, this work focuses for the first time on 1.5 transistor per cell flash memory. The experimental results show hardness varying from about 100 krad(Si) to over 250 krad(Si) depending on the usage model. We explore the circuit and device aspects of the results, based on the extensive reliability literature for this flash memory type. Failure modes indicate both device damage and circuit marginalities. Sector erase failure limits, but read only operation allows TID exceeding 200 krad(Si). The failures are analyzed by type.

[Performance evaluation of CT automatic exposure control on fast dual spiral scan].

PubMed

Niwa, Shinji; Hara, Takanori; Kato, Hideki; Wada, Yoichi

2014-11-01

The performance of individual computed tomography automatic exposure control (CT-AEC) is very important for radiation dose reduction and image quality equalization in CT examinations. The purpose of this study was to evaluate the performance of CT-AEC in conventional pitch mode (Normal spiral) and fast dual spiral scan (Flash spiral) in a 128-slice dual-source CT scanner. To evaluate the response properties of CT-AEC in the 128-slice DSCT scanner, a chest phantom was placed on the patient table and was fixed at the center of the field of view (FOV). The phantom scan was performed using Normal spiral and Flash spiral scanning. We measured the effective tube current time product (Eff. mAs) of simulated organs in the chest phantom along the longitudinal (z) direction, and the dose dependence (distribution) of in-plane locations for the respective scan modes was also evaluated by using a 100-mm-long pencil-type ionization chamber. The dose length product (DLP) was evaluated using the value displayed on the console after scanning. It was revealed that the response properties of CT-AEC in Normal spiral scanning depend on the respective pitches and Flash spiral scanning is independent of the respective pitches. In-plane radiation dose of Flash spiral was lower than that of Normal spiral. The DLP values showed a difference of approximately 1.7 times at the maximum. The results of our experiments provide information for adjustments for appropriate scanning parameters using CT-AEC in a 128-slice DSCT scanner.

Safety and efficacy of low-dose esterified estrogens and methyltestosterone, alone or combined, for the treatment of hot flashes in menopausal women: a randomized, double-blind, placebo-controlled study.

PubMed

Liu, James; Allgood, Adam; Derogatis, Leonard R; Swanson, Stephen; O'Mahony, Michael; Nedoss, Bertrand; Soper, Herbert; Zbella, Edward; Prokofieva, Svetlana Vladimirovna; Zipfel, Lisa; Guo, Chun-Yuan

2011-01-01

This study evaluated safety and efficacy of esterified estrogens and methyltestosterone administered alone or in combination for the treatment of hot flashes in menopausal women. The 0.30-mg esterified estrogens and 0.30-mg methyltestosterone combination was the lowest effective dose, and our results are consistent with the known safety profile of estrogen and androgen combination products. Copyright © 2011 American Society for Reproductive Medicine. Published by Elsevier Inc. All rights reserved.

Continuous background light significantly increases flashing-light enhancement of photosynthesis and growth of microalgae.

PubMed

Abu-Ghosh, Said; Fixler, Dror; Dubinsky, Zvy; Iluz, David

2015-01-01

Under specific conditions, flashing light enhances the photosynthesis rate in comparison to continuous illumination. Here we show that a combination of flashing light and continuous background light with the same integrated photon dose as continuous or flashing light alone can be used to significantly enhance photosynthesis and increase microalgae growth. To test this hypothesis, the green microalga Dunaliella salina was exposed to three different light regimes: continuous light, flashing light, and concomitant application of both. Algal growth was compared under three different integrated light quantities; low, intermediate, and moderately high. Under the combined light regime, there was a substantial increase in all algal growth parameters, with an enhanced photosynthesis rate, within 3days. Our strategy demonstrates a hitherto undescribed significant increase in photosynthesis and algal growth rates, which is beyond the increase by flashing light alone. Copyright © 2015 Elsevier Ltd. All rights reserved.

Effects of estradiol and venlafaxine on insomnia symptoms and sleep quality in women with hot flashes.

PubMed

Ensrud, Kristine E; Guthrie, Katherine A; Hohensee, Chancellor; Caan, Bette; Carpenter, Janet S; Freeman, Ellen W; LaCroix, Andrea Z; Landis, Carol A; Manson, JoAnn; Newton, Katherine M; Otte, Julie; Reed, Susan D; Shifren, Jan L; Sternfeld, Barbara; Woods, Nancy F; Joffe, Hadine

2015-01-01

Determine effects of low-dose estradiol and low-dose venlafaxine on self-reported sleep measures in menopausal women with hot flashes. 3-arm double-blind randomized trial. Participants assigned in a 2:2:3 ratio to 17β estradiol 0.5 mg/day (n = 97), venlafaxine XR 75 mg/day (n = 96), or placebo (n = 146) for 8 weeks. Academic research centers. 339 community-dwelling perimenopausal and postmenopausal women with ≥2 bothersome hot flashes per day. Insomnia symptoms (Insomnia Severity Index [ISI]) and sleep quality (Pittsburgh Sleep Quality Index [PSQI]) at baseline, week 4 and 8; 325 women (96%) provided ISI data and 312 women (92%) provided PSQI data at baseline and follow-up. At baseline, mean (SD) hot flash frequency was 8.1/day (5.3), mean ISI was 11.1 (6.0), and mean PSQI was 7.5 (3.4). Mean (95% CI) change from baseline in ISI at week 8 was -4.1 points (-5.3 to -3.0) with estradiol, -5.0 points (-6.1 to -3.9) with venlafaxine, and -3.0 points (-3.8 to -2.3) with placebo (P overall treatment effect vs. placebo 0.09 for estradiol and 0.007 for venlafaxine). Mean (95% CI) change from baseline in PSQI at week 8 was -2.2 points (-2.8 to -1.6) with estradiol, -2.3 points (-2.9 to -1.6) with venlafaxine, and -1.2 points (-1.7 to -0.8) with placebo (P overall treatment effect vs. placebo 0.04 for estradiol and 0.06 for venlafaxine). Among perimenopausal and postmenopausal women with hot flashes, both low dose oral estradiol and low-dose venlafaxine compared with placebo modestly reduced insomnia symptoms and improved subjective sleep quality. NCT01418209 at www.clinicaltrials.gov. © 2014 Associated Professional Sleep Societies, LLC.

Pharmacokinetics and Bioavailability of Plant Lignan 7-Hydroxymatairesinol and Effects on Serum Enterolactone and Clinical Symptoms in Postmenopausal Women: A Single-Blinded, Parallel, Dose-Comparison Study

PubMed Central

Udani, Jay K.; Brown, Donald J.; Tan, Maria Olivia C.; Hardy, Mary

2013-01-01

Objective 7-Hydroxymaitairesinol (7-HMR) is a naturally occurring plant lignan found in whole grains and the Norway spruce (Piciea abies). The purpose of this study was to evaluate the bioavailability of a proprietary 7-HMR product (HMRlignan, Linnea SA, Locarno, Switzerland) through measurement of lignan metabolites and metabolic precursors. Methods A single-blind, parallel, pharmacokinetic and dose-comparison study was conducted on 22 post-menopausal females not receiving hormone replacement therapy. Subjects were enrolled in either a 36 mg/d (low-dose) or 72 mg/d dose (high-dose) regimen for 8 weeks. Primary measured outcomes included plasma levels of 7-HMR and enterolactone (ENL), and single-dose pharmacokinetic analysis was performed on a subset of subjects in the low-dose group. Safety data and adverse event reports were collected as well as data on hot flash frequency and severity. Results Pharmacokinetic studies demonstrated 7-HMR Cmax = 757.08 ng/ml at 1 hour and ENL Cmax = 4.8 ng/ml at 24 hours. From baseline to week 8, plasma 7-HMR levels increased by 191% in the low-dose group (p < 0.01) and by 1238% in the high-dose group (p < 0.05). Plasma ENL levels consistently increased as much as 157% from baseline in the low-dose group and 137% in the high-dose group. Additionally, the mean number of weekly hot flashes decreased by 50%, from 28.0/week to 14.3/week (p < 0.05) in the high-dose group. No significant safety issues were identified in this study. Conclusion The results demonstrate that HMRlignan is quickly absorbed into the plasma and is metabolized to ENL in healthy postmenopausal women. Clinically, the data demonstrate a statistically significant improvement in hot flash frequency. Doses up to 72 mg/d HMRlignan for 8 weeks were safe and well tolerated in this population. PMID:24606716

Pharmacokinetics and bioavailability of plant lignan 7-hydroxymatairesinol and effects on serum enterolactone and clinical symptoms in postmenopausal women: a single-blinded, parallel, dose-comparison study.

PubMed

Udani, Jay K; Brown, Donald J; Tan, Maria Olivia C; Hardy, Mary

2013-01-01

7-Hydroxymaitairesinol (7-HMR) is a naturally occurring plant lignan found in whole grains and the Norway spruce (Piciea abies). The purpose of this study was to evaluate the bioavailability of a proprietary 7-HMR product (HMRlignan, Linnea SA, Locarno, Switzerland) through measurement of lignan metabolites and metabolic precursors. A single-blind, parallel, pharmacokinetic and dose-comparison study was conducted on 22 postmenopausal females not receiving hormone replacement therapy. Subjects were enrolled in either a 36 mg/d (low-dose) or 72 mg/d dose (high-dose) regimen for 8 weeks. Primary measured outcomes included plasma levels of 7-HMR and enterolactone (ENL), and single-dose pharmacokinetic analysis was performed on a subset of subjects in the low-dose group. Safety data and adverse event reports were collected as well as data on hot flash frequency and severity. Pharmacokinetic studies demonstrated 7-HMR C max = 757.08 ng/ml at 1 hour and ENL C max = 4.8 ng/ml at 24 hours. From baseline to week 8, plasma 7-HMR levels increased by 191% in the low-dose group (p < 0.01) and by 1238% in the high-dose group (p < 0.05). Plasma ENL levels consistently increased as much as 157% from baseline in the low-dose group and 137% in the high-dose group. Additionally, the mean number of weekly hot flashes decreased by 50%, from 28.0/week to 14.3/week (p < 0.05) in the high-dose group. No significant safety issues were identified in this study. The results demonstrate that HMRlignan is quickly absorbed into the plasma and is metabolized to ENL in healthy postmenopausal women. Clinically, the data demonstrate a statistically significant improvement in hot flash frequency. Doses up to 72 mg/d HMRlignan for 8 weeks were safe and well tolerated in this population.

RO brine treatment and recovery by biological activated carbon and capacitive deionization process.

PubMed

Tao, Guihe; Viswanath, Bala; Kekre, Kiran; Lee, Lai Yoke; Ng, How Yong; Ong, Say Leong; Seah, Harry

2011-01-01

The generation of brine solutions from dense membrane (reverse osmosis, RO or nanofiltration, NF) water reclamation systems has been increasing worldwide, and the lack of cost effective disposal options is becoming a critical water resources management issue. In Singapore, NEWater is the product of a multiple barrier water reclamation process from secondary treated domestic effluent using MF/UF-RO and UV technologies. The RO brine (concentrates) accounts for more than 20% of the total flow treated. To increase the water recovery and treat the RO brine, a CDI based process with BAC as pretreatment was tested. The results show that ion concentrations in CDI product were low except SiO2 when compared with RO feed water. CDI product was passed through a RO and the RO permeate was of better quality including low SiO2 as compared to NEWater quality. It could be beneficial to use a dedicated RO operated at optimum conditions with better performance to recover the water. BAC was able to achieve 15-27% TOC removal of RO brine. CDI had been tested at a water recovery ranging from 71.6 to 92.3%. CDI based RO brine treatment could improve overall water recovery of NEWater production over 90%. It was found that calcium phosphate scaling and organic fouling was the major cause of CDI pressure increase. Ozone disinfection and sodium bisulfite dosing were able to reduce CDI fouling rate. For sustainable operation of CDI organic fouling control and effective organic fouling cleaning should be further studied.

Red clover for treatment of hot flashes and menopausal symptoms: A systematic review and meta-analysis.

PubMed

Ghazanfarpour, M; Sadeghi, R; Roudsari, R Latifnejad; Khorsand, I; Khadivzadeh, T; Muoio, B

2016-01-01

This study evaluated the efficacy of red clover to relieve hot flashes and menopausal symptoms in peri/postmenopausal women. Electronic databases (MEDLINE, Scopus and the Cochrane Library) were searched. The mean frequency of hot flashes in red clover groups was lower compared with that in the control groups (close to statistical significance). Difference in means (MD) of hot flashes frequency was - 1.99 (- 4.12-0.139; p = 0.067; heterogeneity P > 0.01; I(2) = 94.93%; Random effect model). Subjective (vaginal dryness) and objective (maturation value) symptoms of vaginal atrophy showed a significant improvement with 80-mg dose of red clover. Red clover showed less therapeutic effect on psychology status, sexual problems and sleeping disorders. Red clover consumption may decrease frequency of hot flashes, especially in women with severe hot flashes (≥ 5 per day). Red clover may reduce other menopausal symptoms. Further trials are needed to confirm the current systematic review findings.

Radiation Tests on 2Gb NAND Flash Memories

NASA Technical Reports Server (NTRS)

Nguyen, Duc N.; Guertin, Steven M.; Patterson, J. D.

2006-01-01

We report on SEE and TID tests of highly scaled Samsung 2Gbits flash memories. Both in-situ and biased interval irradiations were used to characterize the response of the total accumulated dose failures. The radiation-induced failures can be categorized as followings: single event upset (SEU) read errors in biased and unbiased modes, write errors, and single-event-functional-interrupt (SEFI) failures.

Radiation measurement in the environment of FLASH using passive dosimeters

NASA Astrophysics Data System (ADS)

Mukherjee, B.; Rybka, D.; Makowski, D.; Lipka, T.; Simrock, S.

2007-08-01

Sophisticated electronic devices comprising sensitive microelectronic components have been installed in the close proximity of the 720 MeV superconducting electron linear accelerator (linac) driving the FLASH (Free Electron Laser in Hamburg), presently in operation at DESY in Hamburg. Microelectronic chips are inherently vulnerable to ionizing radiation, usually generated during routine operation of high-energy particle accelerator facilities like the FLASH. Hence, in order to assess the radiation effect on microelectronic chips and to develop suitable mitigation strategy, it becomes imperative to characterize the radiation field in the FLASH environment. We have evaluated the neutron and gamma energy (spectra) and dose distributions at critical locations in the FLASH tunnel using superheated emulsion (bubble) detectors, GaAs light emitting diodes (LED), LiF-thermoluminescence dosimeters (TLD) and radiochromic (Gafchromic EBT) films. This paper highlights the application of passive dosimeters for an accurate analysis of the radiation field produced by high-energy electron linear accelerators.

Flash X-Ray Apparatus With Spectrum Control Functions For Medical Use And Fuji Computed Radiography

NASA Astrophysics Data System (ADS)

Isobe, H.; Sato, E.; Hayasi, Y.; Suzuki, M.; Arima, H.; Hoshino, F.

1985-02-01

Flash radiographic bio-medical studies at sub-microsecond intervals were performed by using both a new type of flash X-ray(FX) apparatus with spectrum control functions and Fuji Computed Radiography(FCR). This single flasher tends to have a comparatively long exposure time and the electric pulse width of the FX wave form is about 0.3,usec. The maximum FX dose is about 50mR at 1m per pulse, and the effective focal spot varies according to condenser charging voltage, A-C distance, etc., ranging from 1.0 to 3.0mm in diameter, but in the low dose rate region it can be reduced to less than 1.0mm in diameter. The FX dose is determined by the condenser charging voltage and the A-C distance, while the FX spectrum is determined by the average voltage of the FX tube and filters. Various clear FX images were obtained by controlling the spectrum and dose. FCR is a new storage medium for medical radiography developed by the Fuji Photo Film Co., Ltd. and this apparatus has various image forming functions: low dose radiography, film density control, image contrast control, subtraction management and others. We have used this new apparatus in conjunction with our FX radiography and have obtained some new and interesting biomedical radiograms: the edge enhancement image, the instantaneous enlarged image, and the single exposure energy subtraction image using the FX spectrum distribution.

Phase II evaluation of S-adenosyl-L-methionine (SAMe) for the treatment of hot flashes.

PubMed

Kadakia, Kunal C; Loprinzi, Charles L; Atherton, Pamela J; Fee-Schroeder, Kelliann C; Sood, Amit; Barton, Debra L

2016-03-01

Hot flashes are a significant source of symptom burden that negatively impacts quality of life (QOL). For women who have contraindications to, or are unwilling to consider, estrogens or antidepressants for bothersome hot flashes, there are limited effective pharmacologic or complementary and alternative medicines. This single-arm phase II trial studied the efficacy of S-adenosyl-L-methionine (SAMe) for the treatment of hot flashes. Eligible women were required to have reported ≥14 hot flashes per week for ≥1 month. The patients were treated with SAMe at a dose of 400 mg twice daily to evaluate whether a reduction in hot flash score appeared to be better than the historical placebo response of approximately 25%. The women kept a daily hot flash diary during a baseline week and then daily during weeks 2-7. The primary endpoint was the change from baseline to week 7 in hot flash score and hot flash frequency. Secondary endpoints included toxicity analyses and the effect of SAMe on QOL. From October 28, 2010 to January 30, 2012, 43 women were treated with SAMe. The decrease in mean percent of baseline hot flash score and frequency was 35.4 and 32.6%, respectively. When compared to the historical placebo response of 25%, the effect of SAMe on hot flash score was not statistically significant (p = 0.09). Treatment was well tolerated with expected grade 1/2 gastrointestinal toxicity and no negative effect on QOL. The use of SAMe does not appear to significantly reduce hot flashes more than would be expected with a placebo.

Evaluation of chest CT scan in low-weight children with ultralow tube voltage (70 kVp) combined with Flash scan technique

PubMed Central

Shi, Jiang W; Dai, Hong Z; Shen, Li; Ji, Yi D

2016-01-01

Objective: To assess radiation dose and image quality of chest CT examinations in low-weight children acquired at ultralow tube voltage (70 kVp) combined with Flash scan technique. Materials and methods: 30 consecutive paediatric patients (weight <20 kg) required non-contrast chest CT at 70 kVp with Flash scan mode (Group A). 30 patients for paediatric standard 80-kVp protocols with conventional spiral mode (Group B) were selected from the picture archiving and communication system. For each examination, the volume CT dose index (CTDIvol) and dose–length product (DLP), and the effective dose (adapted as 16-cm phantom) (ED16cm) were estimated. The image noise, signal-to-noise ratio (SNR), overall subjective image quality and respiratory motion artefacts were evaluated. Results: For radiation dose, CTDIvol (mGy), DLP (mGy cm) and ED16cm (mSv) of Group A were significantly lower than those of Group B [CTDIvol: 0.48 ± 0.003 mGy (Group A) vs 0.80 ± 0.005 mGy (Group B); p<0.001 DLP: 10.23 ± 1.35 mGy cm (Group A) vs 15.6 ± 2.02 mGy cm (Group B); p<0.001 ED16cm: 0.61 ± 0.91 mSv (Group A) vs 0.89 ± 0.13 mSv (Group B); p<0.001]. The mean image noise with Group A increased 28.5% (p = 0.002), and the mean SNR decreased 14.8% compared with Group B (p = 0.193). There was no statistical difference in overall subjective image quality grades, and Group A had significantly lower respiratory motion artefact grades than Group B (p < 0.001). Conclusion: Ultralow tube voltage (70 kVp) combined with the Flash scan technique of the chest can obtain images with clinically acceptable image noise and minimum respiratory motion artefacts in low-weight children, whilst reducing radiation dose significantly. Advances in knowledge: The feasibility of chest CT scan in low-weight children with ultralow tube voltage (70 kVp) combined with Flash scan technique has firstly been evaluated in our study. PMID:26781234

Flashes of light-radiation therapy to the brain.

PubMed

Blumenthal, Deborah T; Corn, Benjamin W; Shtraus, Natan

2015-08-01

We present a series of three patients who received therapeutic external beam radiation to the brain and experienced a phenomenon of the sensation of flashes of bright or blue light, simultaneous with radiation delivery. We relate this benign phenomenon to low-dose exposure to the eye fields and postulate that the occurrence is underreported in this treated population. Copyright © 2015 Elsevier Ireland Ltd. All rights reserved.

TU-H-CAMPUS-TeP2-02: FLASH Irradiation Improves the Therapeutic Index Following GI Tract Irradiation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schueler, E; Trovati, S; King, G

Purpose: To investigate and characterize the radiobiological effectiveness of very high dose rate radiotherapy (FLASH) compared to conventional irradiation in an in vivo model. Methods: The gastrointestinal (GI) tract of C57BL/6 mice were irradiated with doses ranging between 10 and 18 Gy using a custom stereotactic jig. A Varian Clinac 21EX was modified to allow dose rates ranging from 0.05 to 240 Gy/s at the position of the mirror. With the gantry at 180 degrees, the jig holding the individual animals was placed above the mirror to take advantage of the reduced source to target distance. Mice were irradiated withmore » 20MeV electrons. Following irradiation, the mice were monitored twice daily for morbidity and daily for weight changes. Results: Mice irradiated with FLASH irradiation had lower weight loss compared to the mice receiving conventional irradiation. Following FLASH irradiation, a maximum weight loss of ∼20% was observed at day 6 with subsequent recovery, while following conventional irradiation, higher weight losses was observed with fewer instances of recovery. Concerning survival, all mice in the conventionally irradiated groups had a 100% mortality in the range of 15.5–18 Gy, while the mice irradiated with FLASH irradiation had a 100% survival in the same range. Conclusion: These results have demonstrated proof of principle that FLASH irradiations have a dramatic impact on the overall survival of mice following GI tract irradiations. If the increase in the therapeutic window can be validated and understood, this would revolutionize the field of radiation oncology and lead to increased cure rates with reduced side effects following treatment, resulting in increased quality of life for cancer survivors. Funding: DoD, Award#:W81XWH-14-1-0014, Weston Havens Foundation, Bio-X (Stanford University), the Office of the Dean of the Medical School, the Office of the Provost (Stanford University), and the Swedish Childhood Cancer Foundation; BL and PM are founders of TibaRay,Inc.; BL and PM have received research grants from Varian and RaySearch Laboratory.« less

Risk Factors, Pathophysiology, and Treatment of Hot Flashes in Cancer

PubMed Central

Fisher, William I.; Johnson, Aimee K.; Elkins, Gary R.; Otte, Julie L.; Burns, Debra S.; Yu, Menggang; Carpenter, Janet S.

2012-01-01

Hot flashes are prevalent and severe symptoms that can interfere with mood, sleep, and quality of life for women and men with cancer. The purpose of this article is to review existing literature on the risk factors, pathophysiology, and treatment of hot flashes in persons with cancer. Electronic searches were conducted to identify relevant, English-language literature published through June 15, 2012. Results indicated that risk factors for hot flashes in cancer include patient-related factors (eg, age, race/ethnicity, educational level, smoking history, cardiovascular risk including BMI, and genetics) and disease-related factors (eg, cancer diagnosis, and dose/type of treatment). In addition, although the pathophysiology of hot flashes has remained elusive, these symptoms are likely attributable to disruptions in thermoregulation and neurochemicals. Therapies that have been offered or tested fall into 4 broad categories: pharmacological, nutraceutical, surgical, and complementary/behavioral strategies. The evidence base for this broad range of therapies varies, with some treatments not yet having been fully tested or showing equivocal results. The evidence base surrounding all therapies is evaluated to enhance hot flash treatment decision making by clinicians and patients. PMID:23355109

The effects of copper fining on the wine content in sulfur off-odors and on their evolution during accelerated anoxic storage.

PubMed

Vela, Eduardo; Hernández-Orte, Purificación; Franco-Luesma, Ernesto; Ferreira, Vicente

2017-09-15

Three different red wines with reductive character have been treated with two different doses of copper sulfate (0.06 and 0.5mg/L) and with a commercial copper-containing product at the recommended dose (0.6mg/L). Wines were in contact with copper one week, centrifuged and stored at 50°C in strict anoxia for 2weeks (up to 7 in one case). Brine-releasable (BR-) and free fractions of Volatile Sulfur Compounds were determined throughout the process. Relevant increases of BR-H 2 S suggest that those wines contained other H 2 S precursors non-detectable by the brine dilution method. Copper treatments had two major effects: 1) immediate decrease the levels of free H 2 S and methanethiol (MeSH); 2) slow the rate at which free H 2 S (not MeSH) increases during anoxic storage. After 7weeks of anoxia levels of free H 2 S and MeSH were high and similar regardless of the copper treatment. Higher copper doses could induce the accumulation of BR-H 2 S. Copyright © 2017 Elsevier Ltd. All rights reserved.

TID and SEE Response of an Advanced Samsung 4G NAND Flash Memory

NASA Technical Reports Server (NTRS)

Oldham, Timothy R.; Friendlich, M.; Howard, J. W.; Berg, M. D.; Kim, H. S.; Irwin, T. L.; LaBel, K. A.

2007-01-01

Initial total ionizing dose (TID) and single event heavy ion test results are presented for an unhardened commercial flash memory, fabricated with 63 nm technology. Results are that the parts survive to a TID of nearly 200 krad (SiO2), with a tractable soft error rate of about 10(exp -l2) errors/bit-day, for the Adams Ten Percent Worst Case Environment.

Blast-Loading Assessment of Multi-Energy Flash Computed Tomography (MEFCT) Diagnostic

DTIC Science & Technology

2016-08-01

Perrella JA, Sturgill JM. Design of a simple blast pressure gauge based on a heterodyne velocimetry measuring technique. Aberdeen Proving Ground (MD...position unless so designated by other authorized documents. Citation of manufacturer’s or trade names does not constitute an official endorsement or...of the radiation dose throughout the angular span of the 150-, 300-, and 450-kV flash X-ray sources used in the MEFCT diagnostic: left image shows

Radiation Tests of Highly Scaled, High-Density, Commercial, Nonvolatile NAND Flash Memories - Update 2012

NASA Technical Reports Server (NTRS)

Irom, Farokh; Allen, Gregory R.

2012-01-01

The space radiation environment poses a certain risk to all electronic components on Earth-orbiting and planetary mission spacecraft. In recent years, there has been increased interest in the use of high-density, commercial, nonvolatile flash memories in space because of ever-increasing data volumes and strict power requirements. They are used in a wide variety of spacecraft subsystems. At one end of the spectrum, flash memories are used to store small amounts of mission-critical data such as boot code or configuration files and, at the other end, they are used to construct multi-gigabyte data recorders that record mission science data. This report examines single-event effect (SEE) and total ionizing dose (TID) response in single-level cell (SLC) 32-Gb, multi-level cell (MLC) 64-Gb, and Triple-level (TLC) 64-Gb NAND flash memories manufactured by Micron Technology with feature size of 25 nm.

Development of cable fed flash X-ray (FXR) system

NASA Astrophysics Data System (ADS)

Menon, Rakhee; Mitra, S.; Patel, A. S.; Kumar, R.; Singh, G.; Senthil, K.; Kumar, Ranjeet; Kolge, T. S.; Roy, Amitava; Acharya, S.; Biswas, D.; Sharma, Archana

2017-08-01

Flash X-ray sources driven by pulsed power find applications in industrial radiography, and a portable X-ray source is ideal where the radiography needs to be taken at the test site. A compact and portable flash X-ray (FXR) system based on a Marx generator has been developed with the high voltage fed to the FXR tube via a cable feed-through arrangement. Hard bremsstrahlung X-rays of few tens of nanosecond duration are generated by impinging intense electron beams on an anode target of high Z material. An industrial X-ray source is developed with source size as low as 1 mm. The system can be operated from 150 kV to 450 kV peak voltages and a dose of 10 mR has been measured at 1 m distance from the source window. The modeling of the FXR source has been carried out using particle-in-cell and Monte Carlo simulations for the electron beam dynamics and X-ray generation, respectively. The angular dose profile of X-ray has been measured and compared with the simulation.

Overview of Reclamation's geothermal program in Imperial Valley, California

NASA Technical Reports Server (NTRS)

Fulcher, M. K.

1974-01-01

The Bureau of Reclamation is presently involved in a unique Geothermal Resource Development Program in Imperial Valley, California. The main purpose of the investigations is to determine the feasibility of providing a source of fresh water through desalting geothermal fluids stored in the aquifers underlying the valley. Significant progress in this research and development stage to date includes extensive geophysical investigations and the drilling of five geothermal wells on the Mesa anomaly. Four of the wells are for production and monitoring the anomaly, and one will be used for reinjection of waste brines from the desalting units. Two desalting units, a multistage flash unit and a vertical tube evaporator unit, have been erected at the East Mesa test site. The units have been operated on shakedown and continuous runs and have produced substantial quantities of high-quality water.

Acute oral toxicity and brine shrimp lethality of Elaeis guineensis Jacq., (oil palm leaf) methanol extract.

PubMed

Syahmi, Abdul Rani Muhamad; Vijayarathna, Soundararajan; Sasidharan, Sreenivasan; Latha, Lachimanan Yoga; Kwan, Yuet Ping; Lau, Yee Ling; Shin, Lai Ngit; Chen, Yeng

2010-11-10

Elaeis guineensis (Arecaceae) is widely used in West African traditional medicine for treating various ailments. An evaluation on the toxicity of extracts of this plant is crucial to support the therapeutic claims. The acute oral toxicity and brine shrimp lethality of a methanolic extract of this plant was tested. Oral administration of crude extract at the highest dose of 5,000 mg/kg resulted in no mortalities or evidence of adverse effects, implying that E. guineensis is nontoxic. Normal behavioral pattern, clinical signs and histology of vital organs confirm this evidence. The E. guineensis extracts screened for toxicity against brine shrimp had 50% lethal concentration (LC₅₀) values of more than 1.0 mg/mL (9.00 and 3.87 mg/mL, at 6 and 24 h, respectively), confirming that the extract was not toxic. Maximum mortalities occurred at 100 mg/mL concentration while the least mortalities happened to be at 0.195 mg/mL concentration. The results of both tests confirm that E. guineensis is nontoxic and hence safe for commercial utilization.

Hemangiomas

MedlinePlus

... grow. The flash-lamp pulse dye, pump dye, diode, and sclero-laser are the primary lasers used ... go through several trials of dosing-tapering. The current protocol is to put them on the initial ...

A Preliminary Performance Assessment for Salt Disposal of High-Level Nuclear Waste - 12173

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lee, Joon H.; Clayton, Daniel; Jove-Colon, Carlos

2012-07-01

A salt repository is one of the four geologic media currently under study by the U.S. DOE Office of Nuclear Energy to support the development of a long-term strategy for geologic disposal of commercial used nuclear fuel (UNF) and high-level radioactive waste (HLW). The immediate goal of the generic salt repository study is to develop the necessary modeling tools to evaluate and improve the understanding of the repository system response and processes relevant to long-term disposal of UNF and HLW in a salt formation. The current phase of this study considers representative geologic settings and features adopted from previous studiesmore » for salt repository sites. For the reference scenario, the brine flow rates in the repository and underlying interbeds are very low, and transport of radionuclides in the transport pathways is dominated by diffusion and greatly retarded by sorption on the interbed filling materials. I-129 is the dominant annual dose contributor at the hypothetical accessible environment, but the calculated mean annual dose is negligibly small. For the human intrusion (or disturbed) scenario, the mean mass release rate and mean annual dose histories are very different from those for the reference scenario. Actinides including Pu-239, Pu-242 and Np-237 are major annual dose contributors, and the calculated peak mean annual dose is acceptably low. A performance assessment model for a generic salt repository has been developed incorporating, where applicable, representative geologic settings and features adopted from literature data for salt repository sites. The conceptual model and scenario for radionuclide release and transport from a salt repository were developed utilizing literature data. The salt GDS model was developed in a probabilistic analysis framework. The preliminary performance analysis for demonstration of model capability is for an isothermal condition at the ambient temperature for the near field. The capability demonstration emphasizes key attributes of a salt repository that are potentially important to the long-term safe disposal of UNF and HLW. The analysis presents and discusses the results showing repository responses to different radionuclide release scenarios (undisturbed and human intrusion). For the reference (or nominal or undisturbed) scenario, the brine flow rates in the repository and underlying interbeds are very low, and transport of radionuclides in the transport pathways is dominated by diffusion and greatly retarded by sorption on the interbed filling materials. I-129 (non-sorbing and unlimited solubility with a very long half-life) is the dominant annual dose contributor at the hypothetical accessible environment, but the calculated mean annual dose is negligibly small that there is no meaningful consequence for the repository performance. For the human intrusion (or disturbed) scenario analysis, the mean mass release rate and mean annual dose histories are very different from those for the reference scenario analysis. Compared to the reference scenario, the relative annual dose contributions by soluble, non-sorbing fission products, particularly I-129, are much lower than by actinides including Pu-239, Pu-242 and Np-237. The lower relative mean annual dose contributions by the fission product radionuclides are due to their lower total inventory available for release (i.e., up to five affected waste packages), and the higher mean annual doses by the actinides are the outcome of the direct release of the radionuclides into the overlying aquifer having high water flow rates, thereby resulting in an early arrival of higher concentrations of the radionuclides at the biosphere drinking water well prior to their significant decay. The salt GDS model analysis has also identified the following future recommendations and/or knowledge gaps to improve and enhance the confidence of the future repository performance analysis. - Repository thermal loading by UNF and HLW, and the effect on the engineered barrier and near-field performance. - Closure and consolidation of salt rocks by creep deformation under the influence of thermal perturbation, and the effect on the engineered barrier and near-field performance. - Brine migration and radionuclide transport under the influence of thermal perturbation in generic salt repository environment, and the effect on the engineered barrier and near-field performance and far-field performance. - Near-field geochemistry and radionuclide mobility in generic salt repository environment (high ionic strength brines, elevated temperatures and chemically reducing condition). - Degradation of engineer barrier components (waste package, waste canister, waste forms, etc.) in a generic salt repository environment (high ionic strength brines, elevated temperatures and chemically reducing condition). - Waste stream types and inventory estimates, particularly for reprocessing high-level waste. (authors)« less

Error Characterization and Mitigation for 16Nm MLC NAND Flash Memory Under Total Ionizing Dose Effect

NASA Technical Reports Server (NTRS)

Li, Yue (Inventor); Bruck, Jehoshua (Inventor)

2018-01-01

A data device includes a memory having a plurality of memory cells configured to store data values in accordance with a predetermined rank modulation scheme that is optional and a memory controller that receives a current error count from an error decoder of the data device for one or more data operations of the flash memory device and selects an operating mode for data scrubbing in accordance with the received error count and a program cycles count.

Combine Flash-Based FPGA TID and Long-Term Retention Reliabilities Through VT Shift

NASA Astrophysics Data System (ADS)

Wang, Jih-Jong; Rezzak, Nadia; Dsilva, Durwyn; Xue, Fengliang; Samiee, Salim; Singaraju, Pavan; Jia, James; Nguyen, Victor; Hawley, Frank; Hamdy, Esmat

2016-08-01

Reliability test results of data retention and total ionizing dose (TID) in 65 nm Flash-based field programmable gate array (FPGA) are presented. Long-chain inverter design is recommended for reliability evaluation because it is the worst case design for both effects. Based on preliminary test data, both issues are unified and modeled by one natural decay equation. The relative contributions of TID induced threshold-voltage shift and retention mechanisms are evaluated by analyzing test data.

A Novel Animal Model to Study Hot Flashes: No Effect of GnRH

PubMed Central

Albertson, Asher J.; Skinner, Donal C.

2009-01-01

Menopausal hot flushes compromise the quality of life for the majority of women. The physiological mechanisms underlying hot flushes remain poorly understood and the absence of an animal model to investigate hot flushes hinders investigations in this field. We have developed the sheep as a model to study peripheral skin temperature changes. Subjecting sheep to fever-inducing treatments with lipopolysaccharide, a significant (P<0.01) change in ear skin temperature was observed. As a strong correlation between luteinizing hormone pulses and hot flushes has previously been reported, we then determined whether intravenous gonadotropin-releasing hormone (GnRH), at doses sufficient to elevate CSF GnRH concentrations, could modulate ear skin temperature. No effect was observed, suggesting that GnRH per se dose not play a role in the etiology of hot flashes. PMID:19512948

The thermodynamic cycle models for geothermal power plants by considering the working fluid characteristic

NASA Astrophysics Data System (ADS)

Mulyana, Cukup; Adiprana, Reza; Saad, Aswad H.; M. Ridwan, H.; Muhammad, Fajar

2016-02-01

The scarcity of fossil energy accelerates the development of geothermal power plant in Indonesia. The main issue is how to minimize the energy loss from the geothermal working fluid so that the power generated can be increased. In some of geothermal power plant, the hot water which is resulted from flashing is flown to injection well, and steam out from turbine is condensed in condenser, while the temperature and pressure of the working fluid is still high. The aim of this research is how the waste energy can be re-used as energy source to generate electric power. The step of the research is started by studying the characteristics of geothermal fluid out from the well head. The temperature of fluid varies from 140°C - 250°C, the pressure is more than 7 bar and the fluid phase are liquid, gas, or mixing phase. Dry steam power plant is selected for vapor dominated source, single or multiple flash power plant is used for dominated water with temperature > 225°C, while the binary power plant is used for low temperature of fluid < 160°C. Theoretically, the process in the power plant can be described by thermodynamic cycle. Utilizing the heat loss of the brine and by considering the broad range of working fluid temperature, the integrated geothermal power plant has been developed. Started with two ordinary single flash power plants named unit 1 and unit 2, with the temperature 250°C resulting power is W1'+W2'. The power is enhanced by utilizing the steam that is out from first stage of the turbine by inputting the steam to the third stage, the power of the plant increase with W1''+W2" or 10% from the original power. By using flasher, the water from unit 1 and 2 is re-flashed at 200°C, and the steam is used to drive the turbine in unit 3, while the water is re-flashed at the temperature170°C and the steam is flown to the same turbine (unit 3) resulting the power of W3+W4. Using the fluid enthalpy, the calculated power of these double and triple flash power plant are 50% of W1+W2. At the last step, the steam out from the turbine of unit 3 with the temperature 150°C is used as a heat source for binary cycle power plant named unit 4, while the hot water from the flasher is used as a heat source for the other binary cycle named unit 5 resulted power W5+W6 or 15% of W1+W2. Using this integrated model the power increased 75% from the original one.

Nonvolatile Memory Technology for Space Applications

NASA Technical Reports Server (NTRS)

Oldham, Timothy R.; Irom, Farokh; Friendlich, Mark; Nguyen, Duc; Kim, Hak; Berg, Melanie; LaBel, Kenneth A.

2010-01-01

This slide presentation reviews several forms of nonvolatile memory for use in space applications. The intent is to: (1) Determine inherent radiation tolerance and sensitivities, (2) Identify challenges for future radiation hardening efforts, (3) Investigate new failure modes and effects, and technology modeling programs. Testing includes total dose, single event (proton, laser, heavy ion), and proton damage (where appropriate). Test vehicles are expected to be a variety of non-volatile memory devices as available including Flash (NAND and NOR), Charge Trap, Nanocrystal Flash, Magnetic Memory (MRAM), Phase Change--Chalcogenide, (CRAM), Ferroelectric (FRAM), CNT, and Resistive RAM.

Total Ionizing Dose Influence on the Single Event Effect Sensitivity in Samsung 8Gb NAND Flash Memories

NASA Astrophysics Data System (ADS)

Edmonds, Larry D.; Irom, Farokh; Allen, Gregory R.

2017-08-01

A recent model provides risk estimates for the deprogramming of initially programmed floating gates via prompt charge loss produced by an ionizing radiation environment. The environment can be a mixture of electrons, protons, and heavy ions. The model requires several input parameters. This paper extends the model to include TID effects in the control circuitry by including one additional parameter. Parameters intended to produce conservative risk estimates for the Samsung 8 Gb SLC NAND flash memory are given, subject to some qualifications.

Analgesic, neuropharmacological, anti-diarrheal, and cytotoxic activities of the extract of Solanum sisymbriifolium (Lam.) leaves.

PubMed

Apu, Apurba Sarker; Bhuyan, Shakhawat Hossan; Matin, Maima; Hossain, Faruq; Khatun, Farjana; Taiab, Abu; Jamaluddin

2013-01-01

The present study was undertaken to evaluate the possible analgesic, neuropharmacological, anti-diarrheal, and cytotoxic activities of the ethanol extract of leaves of Solanum sisymbriifolium Lam. (Family: Solanaceae). The analgesic activity was measured by acetic acid-induced writhing inhibition test. The neuropharmacological activities were evaluated using hole cross, hole board, and elevated plus-maze test and the anti-diarrheal activity was assessed using castor oil-induced diarrhea inhibition method. Brine shrimp lethality bioassay was carried out for assessing the cytotoxicity of the ethanol extract of the leaves. Except cytotoxic activity, all the tests were conducted on mice. The extract at oral doses of 200 and 400 mg/kg body weight showed highly significant (p<0.001) decrease in number of writhing, 52.1±0.66 and 4.4±0.64 compared with the control (78.6±0.29) with the percentage of inhibitions of writhing response were found to be 33.72% and 94.40%, respectively. Compare with the control, the extract at both doses showed significant sedative effect in hole cross test. In hole board test, the extract exhibited highly significant (p<0.001) anxiolytic activity at dose of (200 mg/kg), while the same activity was observed at dose of 400 mg/kg in elevated plus-maze test. The extract showed highly significant (p<0.001) anti-diarrheal activity in a dose-dependent manner. With the extract, significant lethality to brine shrimp was found with LC50 value of 61.66±0.9 μg/ml, which was comparable with the positive control (LC50: 11.89±0.8 µg/ml). The results from the present studies support the traditional uses of this plant part and could form the basis of further investigation including compound isolation.

Micron MT29F128G08AJAAA 128GB Asynchronous Flash Memory Total Ionizing Dose Characterization Test Report

NASA Technical Reports Server (NTRS)

Campola, Michael; Wyrwas, Edward

2017-01-01

The purpose of this test was to characterize the Micron MT29F128G08AJAAAs parameter degradation for total dose response and to evaluate and compare lot date codes for sensitivity. In the test, the device was exposed to both low dose and high dose rate (HDR) irradiations using gamma radiation. Device parameters such as leakage currents, quantity of upset bits and overall chip and die health were investigated to determine which lot is more robust.

Results for the Brine Evaporation Bag (BEB) Brine Processing Test

NASA Technical Reports Server (NTRS)

Delzeit, Lance; Flynn, Michael; Fisher, John; Shaw, Hali; Kawashima, Brian; Beeler, David; Howard, Kevin

2015-01-01

The recent Brine Processing Test compared the NASA Forward Osmosis Brine Dewatering (FOBD), Paragon Ionomer Water Processor (IWP), UMPQUA Ultrasonic Brine Dewatering System (UBDS), and the NASA Brine Evaporation Bag (BEB). This paper reports the results of the BEB. The BEB was operated at 70 deg C and a base pressure of 12 torr. The BEB was operated in a batch mode, and processed 0.4L of brine per batch. Two different brine feeds were tested, a chromic acid-urine brine and a chromic acid-urine-hygiene mix brine. The chromic acid-urine brine, known as the ISS Alternate Pretreatment Brine, had an average processing rate of 95 mL/hr with a specific power of 5kWhr/L. The complete results of these tests will be reported within this paper.

Randomised controlled trial comparing hypnotherapy versus gabapentin for the treatment of hot flashes in breast cancer survivors: a pilot study

PubMed Central

MacLaughlan David, Shannon; Salzillo, Sandra; Bowe, Patrick; Scuncio, Sandra; Malit, Bridget; Raker, Christina; Gass, Jennifer S; Granai, C O; Dizon, Don S

2013-01-01

Objectives To compare the efficacy of hypnotherapy versus gabapentin for the treatment of hot flashes in breast cancer survivors, and to evaluate the feasibility of conducting a clinical trial comparing a drug with a complementary or alternative method (CAM). Design Prospective randomised trial. Setting Breast health centre of a tertiary care centre. Participants 15 women with a personal history of breast cancer or an increased risk of breast cancer who reported at least one daily hot flash. Interventions Gabapentin 900 mg daily in three divided doses (control) compared with standardised hypnotherapy. Participation lasted 8 weeks. Outcome measures The primary endpoints were the number of daily hot flashes and hot flash severity score (HFSS). The secondary endpoint was the Hot Flash Related Daily Interference Scale (HFRDIS). Results 27 women were randomised and 15 (56%) were considered evaluable for the primary endpoint (n=8 gabapentin, n=7 hypnotherapy). The median number of daily hot flashes at enrolment was 4.5 in the gabapentin arm and 5 in the hypnotherapy arm. HFSS scores were 7.5 in the gabapentin arm and 10 in the hypnotherapy arm. After 8 weeks, the median number of daily hot flashes was reduced by 33.3% in the gabapentin arm and by 80% in the hypnotherapy arm. The median HFSS was reduced by 33.3% in the gabapentin arm and by 85% in the hypnotherapy arm. HFRDIS scores improved by 51.6% in the gabapentin group and by 55.2% in the hypnotherapy group. There were no statistically significant differences between groups. Conclusions Hypnotherapy and gabapentin demonstrate efficacy in improving hot flashes. A definitive trial evaluating traditional interventions against CAM methods is feasible, but not without challenges. Further studies aimed at defining evidence-based recommendations for CAM are necessary. Trial registration clinicaltrials.gov (NCT00711529). PMID:24022390

Two examples of indication specific radiation dose calculations in dental CBCT and Multidetector CT scanners.

PubMed

Stratis, Andreas; Zhang, Guozhi; Lopez-Rendon, Xochitl; Politis, Constantinus; Hermans, Robert; Jacobs, Reinhilde; Bogaerts, Ria; Shaheen, Eman; Bosmans, Hilde

2017-09-01

To calculate organ doses and estimate the effective dose for justification purposes in patients undergoing orthognathic treatment planning purposes and temporal bone imaging in dental cone beam CT (CBCT) and Multidetector CT (MDCT) scanners. The radiation dose to the ICRP reference male voxel phantom was calculated for dedicated orthognathic treatment planning acquisitions via Monte Carlo simulations in two dental CBCT scanners, Promax 3D Max (Planmeca, FI) and NewTom VGi evo (QR s.r.l, IT) and in Somatom Definition Flash (Siemens, DE) MDCT scanner. For temporal bone imaging, radiation doses were calculated via MC simulations for a CBCT protocol in NewTom 5G (QR s.r.l, IT) and with the use of a software tool (CT-expo) for Somatom Force (Siemens, DE). All procedures had been optimized at the acceptance tests of the devices. For orthognathic protocols, dental CBCT scanners deliver lower doses compared to MDCT scanners. The estimated effective dose (ED) was 0.32mSv for a normal resolution operation mode in Promax 3D Max, 0.27mSv in VGi-evo and 1.18mSv in the Somatom Definition Flash. For temporal bone protocols, the Somatom Force resulted in an estimated ED of 0.28mSv while for NewTom 5G the ED was 0.31 and 0.22mSv for monolateral and bilateral imaging respectively. Two clinical exams which are carried out with both a CBCT or a MDCT scanner were compared in terms of radiation dose. Dental CBCT scanners deliver lower doses for orthognathic patients whereas for temporal bone procedures the doses were similar. Copyright © 2017 Associazione Italiana di Fisica Medica. Published by Elsevier Ltd. All rights reserved.

Total ionizing dose effect in an input/output device for flash memory

NASA Astrophysics Data System (ADS)

Liu, Zhang-Li; Hu, Zhi-Yuan; Zhang, Zheng-Xuan; Shao, Hua; Chen, Ming; Bi, Da-Wei; Ning, Bing-Xu; Zou, Shi-Chang

2011-12-01

Input/output devices for flash memory are exposed to gamma ray irradiation. Total ionizing dose has been shown great influence on characteristic degradation of transistors with different sizes. In this paper, we observed a larger increase of off-state leakage in the short channel device than in long one. However, a larger threshold voltage shift is observed for the narrow width device than for the wide one, which is well known as the radiation induced narrow channel effect. The radiation induced charge in the shallow trench isolation oxide influences the electric field of the narrow channel device. Also, the drain bias dependence of the off-state leakage after irradiation is observed, which is called the radiation enhanced drain induced barrier lowing effect. Finally, we found that substrate bias voltage can suppress the off-state leakage, while leading to more obvious hump effect.

Isotopic and geochemical characterization of fossil brines of the Cambrian Mt. Simon Sandstone and Ironton-Galesville Formation from the Illinois Basin, USA

NASA Astrophysics Data System (ADS)

Labotka, Dana M.; Panno, Samuel V.; Locke, Randall A.; Freiburg, Jared T.

2015-09-01

Geochemical and isotopic characteristics of deep-seated saline groundwater provide valuable insight into the origin and evolving composition, water-rock interaction, and mixing potential of fossil brines. Such information may yield insight into intra- and interbasinal brine movement and relationships between brine evolution and regional groundwater flow systems. This investigation reports on the δ18O and δD composition and activity values, 87Sr/86Sr ratios and Sr concentrations, and major ion concentrations of the Cambrian-hosted brines of the Mt. Simon Sandstone and Ironton-Galesville Formation and discusses the evolution of these brines as they relate to other intracontinental brines. Brines in the Illinois Basin are dominated by Na-Ca-Cl-type chemistry. The Mt. Simon and overlying Ironton-Galesville brines exhibit total dissolved solids concentrations of ∼195,000 mg/L and ∼66,270 mg/L, respectively. The δD of brine composition of the Mt. Simon ranges from -34‰ to -22‰ (V-SMOW), and the Ironton-Galesville is ∼-53.2‰ (V-SMOW). The δ18O composition of the Mt. Simon brine ranges from -5.0‰ to -2.8‰ (V-SMOW), and the Ironton-Galesville brine is ∼-6.9‰ (V-SMOW). The 87Sr/86Sr values in the Mt. Simon brine range from 0.7110 to 0.7116. The less radiogenic Ironton-Galesville brine has an average 87Sr/86Sr value of 0.7107. Evaluation of δ18O and δD composition and activities and 87Sr/86Sr ratios suggests that the Mt. Simon brine is likely connate seawater and recirculating deep-seated brines that have been diluted with meteoric water and influenced by the dissolution of evaporites with a minimal halite contribution based on Cl/Br ratios. The Ironton-Galesville brine is also likely originally connate seawater that mixed with other brines and meteoric waters, including possibly Pleistocene glacial recharge. The Ca-excess vs. Na-deficiency comparison with the Basinal Fluid Line suggests the Mt. Simon and Ironton-Galesville brines have been influenced by the effects of albitization and plot very close to the Basinal Fluid Line. These Cambrian-hosted brines appear to have a different albitization history than other regional basin brines and a strong component of seawater. The Ironton-Galesville brine appears more geochemically associated with other Illinois Basin brines than the Mt. Simon brine which appears more geochemically conservative. Comparisons with other extrabasinal North American brines suggest that the Michigan basin brines are geochemically most similar to the Mt. Simon brines with the exception of the influence from carbonates in the Michigan Basin. Analyses of 87Sr/86Sr values in the Mt. Simon brine suggest that brine Sr has isotopically equilibrated with clay minerals in the Lower Mt. Simon and underlying bedrock formations and not with whole rock suggesting the influence of recirculating brines from the crystalline basement. Overall, the geochemistry of these Cambrian-hosted brines suggests an evolution from original seawater-like compositions. This investigation shows that intracratonic basins do not behave as closed systems but can be strongly affected by water-rock interaction and regional groundwater flow systems that circulate deep crystalline basement brines and brines from nearby basins.

CD uniformity control for thick resist process

NASA Astrophysics Data System (ADS)

Huang, Chi-hao; Liu, Yu-Lin; Wang, Weihung; Yang, Mars; Yang, Elvis; Yang, T. H.; Chen, K. C.

2017-03-01

In order to meet the increasing storage capacity demand and reduce bit cost of NAND flash memories, 3D stacked flash cell array has been proposed. In constructing 3D NAND flash memories, the higher bit number per area is achieved by increasing the number of stacked layers. Thus the so-called "staircase" patterning to form electrical connection between memory cells and word lines has become one of the primarily critical processes in 3D memory manufacture. To provide controllable critical dimension (CD) with good uniformity involving thick photo-resist has also been of particular concern for staircase patterning. The CD uniformity control has been widely investigated with relatively thinner resist associated with resolution limit dimension but thick resist coupling with wider dimension. This study explores CD uniformity control associated with thick photo-resist processing. Several critical parameters including exposure focus, exposure dose, baking condition, pattern size and development recipe, were found to strongly correlate with the thick photo-resist profile accordingly affecting the CD uniformity control. To minimize the within-wafer CD variation, the slightly tapered resist profile is proposed through well tailoring the exposure focus and dose together with optimal development recipe. Great improvements on DCD (ADI CD) and ECD (AEI CD) uniformity as well as line edge roughness were achieved through the optimization of photo resist profile.

7 CFR 58.422 - Brine tank.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 7 Agriculture 3 2014-01-01 2014-01-01 false Brine tank. 58.422 Section 58.422 Agriculture....422 Brine tank. The brine tank shall be constructed of suitable non-toxic material and should be resistant to corrosion, pitting or flaking. The brine tank shall be operated so as to assure the brine is...

7 CFR 58.422 - Brine tank.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 7 Agriculture 3 2012-01-01 2012-01-01 false Brine tank. 58.422 Section 58.422 Agriculture....422 Brine tank. The brine tank shall be constructed of suitable non-toxic material and should be resistant to corrosion, pitting or flaking. The brine tank shall be operated so as to assure the brine is...

7 CFR 58.422 - Brine tank.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 7 Agriculture 3 2013-01-01 2013-01-01 false Brine tank. 58.422 Section 58.422 Agriculture....422 Brine tank. The brine tank shall be constructed of suitable non-toxic material and should be resistant to corrosion, pitting or flaking. The brine tank shall be operated so as to assure the brine is...

7 CFR 58.422 - Brine tank.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 3 2011-01-01 2011-01-01 false Brine tank. 58.422 Section 58.422 Agriculture....422 Brine tank. The brine tank shall be constructed of suitable non-toxic material and should be resistant to corrosion, pitting or flaking. The brine tank shall be operated so as to assure the brine is...

A comparison of the central nervous system effects of haloperidol, chlorpromazine and sulpiride in normal volunteers.

PubMed Central

McClelland, G R; Cooper, S M; Pilgrim, A J

1990-01-01

1. Twelve healthy male volunteers participated in four experimental occasions during each of which they were dosed with one of the following anti-psychotic drugs: chlorpromazine (50 mg), haloperidol (3 mg), sulpiride (400 mg) and placebo. Drugs were allocated to subjects in a double-blind, crossover fashion. 2. The subject's mood state, psychometric performance and electroencephalogram (EEG) were assessed pre-dose, and at 2, 4, 6, 8, 24 and 48 h post-dose. Mood states were assessed using 16 visual analogue scales and psychomotor performance was measured using the following tests: elapsed time estimation, tapping rate, choice reaction times, a rapid information processing task, flash fusion threshold, a manipulative motor task, digit span, body sway and tremor. 3. Chlorpromazine and haloperidol significantly reduced subjective ratings of 'alertness' and 'contentedness', and haloperidol significantly reduced feelings of 'calmness'. Sulpiride did not significantly affect any of the visual analogue scales. 4. All three anti-psychotic drugs had similar EEG effects with peak effect 2 to 4 h postdose. The profile was characterised by an increase in the proportion of slow wave activity (delta and theta) as well as decreased alpha (8-14 Hz) and faster (beta) wave activity. 5. Chlorpromazine reduced tapping rate and increased choice reaction movement times. Haloperidol reduced the flash fusion threshold frequency at 6 h post-dose. Sulpiride prolonged the duration of the manipulative motor task, particularly at 48 h post-dose. 6. All three anti-psychotic drugs impaired performance on the rapid information processing task. Chlorpromazine significantly reduced the number of correct letter pair identifications at 2, 4 and 6 h post-dose, haloperidol at 4, 6, 8, 24 and 48 h post-dose, and sulpiride at 24 h post-dose.(ABSTRACT TRUNCATED AT 250 WORDS) PMID:2288826

Pooled Analysis of Six Pharmacologic and Nonpharmacologic Interventions for Vasomotor Symptoms.

PubMed

Guthrie, Katherine A; LaCroix, Andrea Z; Ensrud, Kristine E; Joffe, Hadine; Newton, Katherine M; Reed, Susan D; Caan, Bette; Carpenter, Janet S; Cohen, Lee S; Freeman, Ellen W; Larson, Joseph C; Manson, JoAnn E; Rexrode, Kathy; Skaar, Todd C; Sternfeld, Barbara; Anderson, Garnet L

2015-08-01

To describe the effects of six interventions for menopausal vasomotor symptoms relative to control in a pooled analysis, facilitating translation of the results for clinicians and symptomatic women. The Menopause Strategies: Finding Lasting Answers for Symptoms and Health network tested these interventions in three randomized clinical trials. An analysis of pooled individual-level data from three randomized clinical trials is presented. Participants were 899 perimenopausal and postmenopausal women with at least 14 bothersome vasomotor symptoms per week. Interventions included 10-20 mg escitalopram per day, nonaerobic yoga, aerobic exercise, 1.8 g per day omega-3 fatty acid supplementation, 0.5 mg low-dose oral 17-beta-estradiol (E2) per day, and 75 mg low-dose venlafaxine XR per day. The main outcome measures were changes from baseline in mean daily vasomotor symptom frequency and bother during 8-12 weeks of treatment. Linear regression models estimated differences in outcomes between each intervention and corresponding control group adjusted for baseline characteristics. Models included trial-specific intercepts, effects of the baseline outcome measure, and time. The 8-week reduction in vasomotor symptom frequency from baseline relative to placebo was similar for escitalopram at -1.4 per day (95% confidence interval [CI] -2.7 to -0.2), low-dose E2 at -2.4 (95% CI -3.4 to -1.3), and venlafaxine at -1.8 (95% CI -2.8 to -0.8); vasomotor symptom bother reduction was minimal and did not vary across these three pharmacologic interventions (mean -0.2 to -0.3 relative to placebo). No effects on vasomotor symptom frequency or bother were seen with aerobic exercise, yoga, or omega-3 supplements. These analyses suggest that escitalopram, low-dose E2, and venlafaxine provide comparable, modest reductions in vasomotor symptom frequency and bother among women with moderate hot flushes. ClinicalTrials.gov, www.clinicaltrials.gov, NCT00894543 (MsFLASH 01), NCT01178892 (MsFLASH 02), and NCT01418209 (MsFLASH 03).

Quantitative oral dosing of water soluble and lipophilic contaminants in the Japanese medaka (Oryzias latipes).

PubMed

Schultz, I R; Reed, S; Pratt, A; Skillman, A D

2007-02-01

Quantitative oral dosing in fish can be challenging, particularly with water soluble contaminants, which can leach into the aquarium water prior to ingestion. We applied a method of bioencapsulation using newly hatched brine shrimp (Artemia franciscana) nauplii to study the toxicokinetics of five chlorinated and brominated halogenated acetic acids (HAAs), which are drinking water disinfection by-products. These results are compared to those obtained in a previous study using a polybrominated diphenyl ether (PBDE-47), a highly lipophilic chemical. The HAAs and PBDE-47 were bioencapsulated using freshly hatched A. franciscana nauplii after incubation in concentrated solutions of the study chemicals for 18 h. Aliquots of the brine shrimp were quantitatively removed for chemical analysis and fed to individual fish that were able to consume 400-500 nauplii in less than 5 min. At select times after feeding, fish were euthanized and the HAA or PBDE-47 content determined. The absorption of HAAs was quantitatively similar to previous studies in rodents: rapid absorption with peak body levels occurring within 1-2 h, then rapidly declining with elimination half-life of 0.3-3 h depending on HAA. PBDE-47 was more slowly absorbed with peak levels occurring by 18 h and very slowly eliminated with an elimination half-life of 281 h.

Flash x-ray radiography of argon jets in ambient air

NASA Astrophysics Data System (ADS)

Geiswiller, J.; Robert, E.; Huré, L.; Cachoncinlle, C.; Viladrosa, R.; Pouvesle, J. M.

1998-09-01

This paper describes the development and application of a soft x-ray flash radiography technique. A very compact soft x-ray flash source has been specially designed for these studies. The table-top x-ray source developed in this work emits strong doses, up to one roentgen at the output window, of x-ray photons, with most of them in the characteristic lines of the anode material (photon energy in the energy range 5-10 keV), in pulse of 20 ns FWHM with an x-ray emission zone smaller than 0957-0233/9/9/024/img1. All these characteristics make this source attractive for the x-ray radiography of high-speed phenomena, down to ten nanoseconds duration and/or for the media presenting weak absorption for the harder x-ray photons emitted by more conventional flash x-ray systems. Argon streams in ambient air were chosen as a typical case to enlighten the potentialities of this method. Single-shot radiographs of such an argon jet through rectangular nozzles were obtained. No attempt of quantitative measurement of local density in the argon stream has yet been performed, only the qualitative structure of the jet has been investigated. Nevertheless, these preliminary results enable us to state that the diagnostics of gaseous or plasma media, even at rather low pressures, can proceed using soft x-ray flash radiography.

Phytochemistry, Brine shrimp lethality and mice acute oral toxicity studies on seed extracts of Vernonia anthelmintica.

PubMed

Jamil, Subia; Khan, Rafeeq Alam; Afroz, Syeda; Ahmed, Shadab

2016-11-01

Despite the widespread use of Vernonia anthelmintica seeds in traditional medicine, the need to establish the safety of the Vernonia anthelmintica is required to ascertain the safe use of this herbal medicine. The aim of the present study is to establish the acute toxicity profile of different extracts of Vernonia anthelmintica. Hexane and ethanol extract of Vernonia Anthelmintica has been studied for its brine shrimp lethality potential. Water decoction (WDVA), Hexane (HEVA) and Ethanol (EEVA) extracts of Vernonia anthelmintica has also been evaluated for their in-vivo acute oral toxicity in mice by Lorke's method. Phytochemistry of all three extracts was also evaluated for the presence of their secondary metabolites. All three extracts showed the presence of flavonoids and terpenoids, while alkaloids, tannins and fixed oils were present in HEVA and EEVA. Furthermore EEVA also showed presence of carbohydrates and HEVA also showed the presence of cardiac glycosides. Ethanol and hexane extracts of Vernonia anthelmintica showed a positive cytotoxicity in brine shrimp lethality test at 24 hours with LC50 104.16 (224.0-48.05)μg/ml and 216.11μg/ml (378.2-128.7) respectively as compared to standard drug etoposide LC50 7.46μg/ml. The oral LD50 for EEVA, HEVA and WDVA in mice by Lorke's method was greater than 5000mg/kg. The result of brine shrimp lethality test clearly exhibited the presence of bioactive compounds with cytotoxic potential; however seems to be safe for oral use since LD50 was higher than 5000mg/kg and thus safety of acute dosing in vivo practices is justified.

Acute toxicity, bioaccumulation and effects of dietary transfer of silver from brine shrimp exposed to PVP/PEI-coated silver nanoparticles to zebrafish.

PubMed

Lacave, José María; Fanjul, Álvaro; Bilbao, Eider; Gutierrez, Nerea; Barrio, Irantzu; Arostegui, Inmaculada; Cajaraville, Miren P; Orbea, Amaia

2017-09-01

The extensive use and release to the aquatic environment of silver nanoparticles (NPs) could lead to their incorporation into the food web. Brine shrimp larvae of 24h showed low sensitivity to the exposure to PVP/PEI-coated Ag NPs (5nm), with EC 50 values at 24h of 19.63mgAgL -1 , but they significantly accumulated silver after 24h of exposure to 100μgL -1 of Ag NPs. Thus, to assess bioaccumulation and effects of silver transferred by the diet in zebrafish, brine shrimp larvae were exposed to 100ngL -1 of Ag NPs as an environmentally relevant concentration or to 100μgL -1 as a potentially effective concentration and used to feed zebrafish for 21days. Autometallography revealed a dose- and time-dependent metal accumulation in the intestine and in the liver of zebrafish. Three-day feeding with brine shrimps exposed to 100ngL -1 of Ag NPs was enough to impair fish health as reflected by the significant reduction of lysosomal membrane stability and the presence of vacuolization and necrosis in the liver. However, dietary exposure to 100μgL -1 of Ag NPs for 3days did not significantly alter gene transcription levels, neither in the liver nor in the intestine. After 21days, biological processes such as lipid transport and localization, cellular response to chemical stimulus and response to xenobiotic stimulus were significantly altered in the liver. Overall, these results indicate an effective dietary transfer of silver and point out to liver as the main target organ for Ag NP toxicity in zebrafish after dietary exposure. Copyright © 2017 Elsevier Inc. All rights reserved.

Diversity within Italian Cheesemaking Brine-Associated Bacterial Communities Evidenced by Massive Parallel 16S rRNA Gene Tag Sequencing

PubMed Central

Marino, Marilena; Innocente, Nadia; Maifreni, Michela; Mounier, Jérôme; Cobo-Díaz, José F.; Coton, Emmanuel; Carraro, Lisa; Cardazzo, Barbara

2017-01-01

This study explored the bacterial diversity of brines used for cheesemaking in Italy, as well as their physicochemical characteristics. In this context, 19 brines used to salt soft, semi-hard, and hard Italian cheeses were collected in 14 commercial cheese plants and analyzed using a culture-independent amplicon sequencing approach in order to describe their bacterial microbiota. Large NaCl concentration variations were observed among the selected brines, with hard cheese brines exhibiting the highest values. Acidity values showed a great variability too, probably in relation to the brine use prior to sampling. Despite their high salt content, brine microbial loads ranged from 2.11 to 6.51 log CFU/mL for the total mesophilic count. Microbial community profiling assessed by 16S rRNA gene sequencing showed that these ecosystems were dominated by Firmicutes and Proteobacteria, followed by Actinobacteria and Bacteroidetes. Cheese type and brine salinity seem to be the main parameters accountable for brine microbial diversity. On the contrary, brine pH, acidity and protein concentration, correlated to cheese brine age, did not have any selective effect on the microbiota composition. Nine major genera were present in all analyzed brines, indicating that they might compose the core microbiome of cheese brines. Staphylococcus aureus was occasionally detected in brines using selective culture media. Interestingly, bacterial genera associated with a functional and technological use were frequently detected. Indeed Bifidobacteriaceae, which might be valuable probiotic candidates, and specific microbial genera such as Tetragenococcus, Corynebacterium and non-pathogenic Staphylococcus, which can contribute to sensorial properties of ripened cheeses, were widespread within brines. PMID:29163411

Analgesic, neuropharmacological, anti-diarrheal, and cytotoxic activities of the extract of Solanum sisymbriifolium (Lam.) leaves

PubMed Central

Apu, Apurba Sarker; Bhuyan, Shakhawat Hossan; Matin, Maima; Hossain, Faruq; Khatun, Farjana; Taiab, Abu; Jamaluddin

2013-01-01

Objective: The present study was undertaken to evaluate the possible analgesic, neuropharmacological, anti-diarrheal, and cytotoxic activities of the ethanol extract of leaves of Solanum sisymbriifolium Lam. (Family: Solanaceae). Materials and Methods: The analgesic activity was measured by acetic acid-induced writhing inhibition test. The neuropharmacological activities were evaluated using hole cross, hole board, and elevated plus-maze test and the anti-diarrheal activity was assessed using castor oil-induced diarrhea inhibition method. Brine shrimp lethality bioassay was carried out for assessing the cytotoxicity of the ethanol extract of the leaves. Except cytotoxic activity, all the tests were conducted on mice. Results: The extract at oral doses of 200 and 400 mg/kg body weight showed highly significant (p<0.001) decrease in number of writhing, 52.1±0.66 and 4.4±0.64 compared with the control (78.6±0.29) with the percentage of inhibitions of writhing response were found to be 33.72% and 94.40%, respectively. Compare with the control, the extract at both doses showed significant sedative effect in hole cross test. In hole board test, the extract exhibited highly significant (p<0.001) anxiolytic activity at dose of (200 mg/kg), while the same activity was observed at dose of 400 mg/kg in elevated plus-maze test. The extract showed highly significant (p<0.001) anti-diarrheal activity in a dose-dependent manner. With the extract, significant lethality to brine shrimp was found with LC50 value of 61.66±0.9 μg/ml, which was comparable with the positive control (LC50: 11.89±0.8 µg/ml). Conclusion: The results from the present studies support the traditional uses of this plant part and could form the basis of further investigation including compound isolation. PMID:25050287

Silica Precipitation from Geothermal Brines: Effects of Iron Addition, Kinetics, Temperature, pH, and Brine Concentration

DOE Data Explorer

Jay Renew

2016-02-06

This document provides results of experiments aimed at removing silica from geothermal brines. All experiments were conducted with simulated brines. The data presented shows the effect of iron addition, kinetics, temperature, pH and brine concentration.

Neutrons from thunderstorms at low atmospheric altitudes and related doses at aircraft

NASA Astrophysics Data System (ADS)

Drozdov, A.; Grigoriev, A.

2013-02-01

We conduct a simulation of thunderstorm neutron flashes at the lowest atmospheric altitudes below 10 km. The neutron generation mechanism is based on the nowadays conventional idea of possibility for photonuclear reactions to proceed on the atmospheric components owing to TGF photons. Our modeling includes generation of neutrons from TGF and their further propagation with account of interaction with background nuclei. Using the calculation results we investigate the neutron flux properties with respect to problem of their registration, and predict the radiation environment caused by thunderstorm neutrons on altitudes of civil airflights. It is shown, that good conditions for the neutron flashes observation are provided from the 3 km altitude, and, possibly, the neutrons can be registered at ground level. We also found that thunderstorm-neutron-related effective dose can reach the value of 0.5 mSv in the region close to the TGF source if it is located at an altitude of 10 km.

[Comparison of radiation dose reduction of prospective ECG-gated one beat scan using 320 area detector CT coronary angiography and prospective ECG-gated helical scan with high helical pitch (FlashScan) using 64 multidetector-row CT coronary angiography].

PubMed

Matsutani, Hideyuki; Sano, Tomonari; Kondo, Takeshi; Fujimoto, Shinichiro; Sekine, Takako; Arai, Takehiro; Morita, Hitomi; Takase, Shinichi

2010-12-20

A high radiation dose associated with 64 multidetector-row computed tomography (64-MDCT) is a major concern for physicians and patients alike. A new 320 row area detector computed tomography (ADCT) can obtain a view of the entire heart with one rotation (0.35 s) without requiring the helical method. As such, ADCT is expected to reduce the radiation dose. We studied image quality and radiation dose of ADCT compared to that of 64-MDCT in patients with a low heart rate (HR≤60). Three hundred eighty-five consecutive patients underwent 64-MDCT and 379 patients, ADCT. Patients with an arrhythmia were excluded. Prospective ECG-gated helical scan with high HP (FlashScan) in 64 was used for MDCT and prospective ECG-gated conventional one beat scan, for 320-ADCT. Image quality was visually evaluated by an image quality score. Radiation dose was estimated by DLP (mGy･cm) for 64-MDCT and DLP.e (mGy･cm) for 320-ADCT. Radiation dose of 320-ADCT (208±48 mGy･cm) was significantly (P<0.0001) lower than that of 64-MDCT (484±112 mGy･cm), and image quality score of 320-ADCT (3.0±0.2) was significantly (P=0.0011) higher than that of 64-MDCT (2.9±0.4). Scan time of 320-ADCT (1.4±0.1 s) was also significantly (P<0.0001) shorter than that of 64-MDCT (6.8±0.6 s). 320-ADCT can achieve not only a reduction in radiation dose but also a superior image quality and shortening of scan time compared to 64-MDCT.

Bioactivity studies on Musa seminifera Lour

PubMed Central

Saha, Sanjib; Shilpi, Jamil A.; Mondal, Himangsu; Gofur, Royhan; Billah, Morsaline; Nahar, Lutfun; Sarker, Satyajit D.

2013-01-01

Background: Musa seminifera Lour is a tree-like perennial herb that has been used in folk medicine in Bangladesh to heal a number of ailments. Objective: To evaluate the antioxidant, analgesic, antidiarrheal, anthelmintic activities, and general toxicity of the ethanol extract of the roots. Materials and Methods: The extract was assessed for free-radical-scavenging activity by the 2,2-diphenyl-1-picrylhydrazyl (DPPH) assay, total phenolic content (TPC) by the Folin Ciocalteu reagent, antioxidant activity by the ferric reducing power assay, analgesic activity by the acetic acid-induced writhing and hot-plate tests, antidiarrheal activity by the castor oil-induced diarrhea model in mice, anthelmintic activity on Paramphistomum cervi and Haemonchus contortus, and general toxicity by the brine shrimp lethality assay. Results: The extract showed free-radical-scavenging activity with an IC50 value of 44.86 μg/mL. TPC was 537.89 mg gallic acid equivalent/100 g of dried plant material. It showed concentration-dependent reducing power, and displayed 42.11 and 69.32% writhing inhibition at doses of 250 and 500 mg/kg body weight, respectively. The extract also significantly raised the pain threshold at the above-mentioned dose levels. In vivo antidiarrheal property was substantiated by significant prolongation of latent period and decrease in total number of stools compared with the control. The LC50 against brine shrimp nauplii was 36.21 μg/mL. The extract exhibited dose-dependent decrease in paralysis and death time of the helminths. Conclusion: The above results demonstrated that the plant possesses notable bioactivities and somewhat supports its use in folk medicine. PMID:24124283

Photocatalytic reduction of nitrate using titanium dioxide for regeneration of ion exchange brine

PubMed Central

Yang, Ting; Doudrick, Kyle; Westerhoff, Paul

2016-01-01

Nitrate is often removed from groundwater by ion exchange (IX) before its use as drinking water. Accumulation of nitrate in IX brine reduces the efficiency of IX regeneration and the useful life of the regeneration brine. For the first time, we present a strategy to photocatalytically reduce nitrate in IX brine, thereby extending the use of the brine. Titanium dioxide (Evonik P90), acting as photocatalyst, reduced nitrate effectively in both synthetic brines and sulfate-removed IX brine when formic acid (FA) was used as the hole scavenger (i.e., electron donor) and the initial FA to nitrate molar ratio (IFNR) was 5.6. Increasing the NaCl level in the synthetic brine slowed the nitrate reduction rate without affecting byproduct selectivity of ammonium and gaseous N species (e.g., N2, N2O). In a non-modified IX brine, nitrate removal was greatly inhibited owing to the presence of sulfate, which competed with nitrate for active surface sites on P90 and induced aggregation of P90 nanoparticles. After removing sulfate through barium sulfate precipitation, nitrate was effectively reduced; approximately 3.6 × 1024 photons were required to reduce each mole of nitrate to 83% N Gases and 17% NH4+. To make optimum use of FA and control the residual FA level in treated brine, the IFNR was varied. High IFNRs (e.g., 4, 5.6) were found to be more efficient for nitrate reduction but left higher residual FA in brine. IX column tests were performed to investigate the impact of residual FA for brine reuse. The residual FA in the brine did not significantly affect the nitrate removal capacity of IX resins, and formate contamination of treated water could be eliminated by rinsing with one bed volume of fresh brine. PMID:23276425

Forward Osmosis Brine Drying

NASA Technical Reports Server (NTRS)

Flynn, Michael; Shaw, Hali; Hyde, Deirdre; Beeler, David; Parodi, Jurek

2015-01-01

The Forward Osmosis Brine Drying (FOBD) system is based on a technique called forward osmosis (FO). FO is a membrane-based process where the osmotic potential between brine and a salt solution is equalized by the movement of water from the brine to the salt solution. The FOBD system is composed of two main elements, the FO bag and the salt regeneration system. This paper discusses the results of testing of the FO bag to determine the maximum water recovery ratio that can be attained using this technology. Testing demonstrated that the FO bag is capable of achieving a maximum brine water recovery ratio of the brine of 95%. The equivalent system mass was calculated to be 95 kg for a feed similar to the concentrated brine generated on the International Space Station and 86 kg for an Exploration brine. The results have indicated that the FOBD can process all the brine for a one year mission for between 11% to 10% mass required to bring the water needed to make up for water lost in the brine if not recycled. The FOBD saves 685 kg and when treating the International Space Station brine and it saves 829 kg when treating the Exploration brine. It was also demonstrated that saturated salt solutions achieve a higher water recovery ratios than solids salts do and that lithium chloride achieved a higher water recovery ratio than sodium chloride.

Natural Oxidation of Bromide to Bromine in Evaporated Dead Sea Brines

NASA Astrophysics Data System (ADS)

Gavrieli, Ittai; Golan, Rotem; Lazar, Boaz; Baer, Gidi; Zakon, Yevgeni; Ganor, Jiwchar

2016-04-01

Highly evaporated Dead Sea brines are found in isolated sinkholes along the Dead Sea. Many of these brines reach densities of over 1.3 kg/L and pH<5 and are the product of evaporation of Dead Sea brine that drain into the sinkholes. The low pH and the reddish to brownish hue of these brines were an enigma until recently. Despite the rather high total alkalinity (TA) of the Dead Sea (3.826 mmol/kg) the pH of the Dead Sea brine is known to be slightly acidic with a value of ~6.3. In comparison, seawater with the same alkalinity would have a pH value well above 8.3, meaning that H+ activity is 100 fold lower than that of Dead Sea brine. In the present work we assess the apparent dissociation constant value of boric acid (K`B) for the Dead Sea brine and use it to explain the brine's low pH value. We then show that pH decreases further as the brine evaporates and salinity increases. Finally we explain the reddish hue of the hypersaline brines in the sinkholes as due to the presence of dissolved bromine. The latter is the product of oxidation of dissolved bromide, a process that is enabled by the low pH of the hypersaline brines and their high bromide concentration.

Experimental multi-phase CO2-brine-rock interactions at elevated temperature and pressure: Implications for CO2 sequestration in deep-saline aquifers

USGS Publications Warehouse

Rosenbauer, R.J.; Koksalan, T.

2004-01-01

Long-term CO2 saturated brine-rock experiments were conducted to evaluate the effects of multiphase H2O-CO2 fluids on mineral equilibria and the potential for CO2 sequestration mineral phases within deep-saline aquifers. Experimental results were consistent with theoretical thermodynamic calculations when CO2-saturated brines were reacted with limestone rocks. The CO2-saturated brine-limestone reactions were characterized by compositional and mineralogical-changes in the aquifer fluid and formation rocks that were dependent on initial brine composition as were the changes in formation porosity, especially dissolved sulfate. The solubility of CO2 was enhanced in brines in the presence of both limestone and sandstone rocks relative to brines alone. Reactions between CO2 saturated brines and arkosic sandstones were characterized by desiccation of the brine and changes in the chemical composition of the brine suggesting fixation of CO2 in mineral phases. These reactions occured on a measurable but kinetically slow time scale at 120??C.

Comparison of Four Strong Acids on the Precipitation Potential of Gypsum in Brines During Distillation of Pretreated, Augmented Urine

NASA Technical Reports Server (NTRS)

Muirhead, Dean; Carrier, Christopher

2012-01-01

In this study, three different mineral acids were substituted for sulfuric acid (H2SO4) in the urine stabilizer solution to eliminate the excess of sulfate ions in pretreated urine and assess the impact on maximum water recovery to avoid precipitation of minerals during distillation. The study evaluated replacing 98% sulfuric acid with 85% phosphoric acid (H3PO4), 37% hydrochloric acid (HCl), or 70% nitric acid (HNO3). The effect of lowering the oxidizer concentration in the pretreatment formulation also was studied. This paper summarizes the test results, defines candidate formulations for further study, and specifies the injection masses required to stabilize urine and minimize the risk of mineral precipitation during distillation. In the first test with a brine ersatz acidified with different acids, the solubility of calcium in gypsum saturated solutions was measured. The solubility of gypsum was doubled in the brines acidified with the alternative acids compared to sulfuric acid. In a second series of tests, the alternative acid pretreatment concentrations were effective at preventing precipitation of gypsum and other minerals up to 85% water recovery from 95th-percentile pretreated, augmented urine. Based on test results, phosphoric acid is recommended as the safest alternative to sulfuric acid. It also is recommended that the injected mass concentration of chromium trioxide solution be reduced by 75% to minimize liquid resupply mass by about 50%, reduce toxicity of brines, and reduce the concentration of organic acids in distillate. The new stabilizer solution formulations and required doses to stabilize urine and prevent precipitation of minerals up to 85% water recovery are given. The formulations in this study were tested on a limited number of artificially augmented urine batches collected from employees at the Johnson Space Center (JSC). This study successfully demonstrated that the desired physical and chemical stability of pretreated urine and brines can be achieved using alternate pretreatment formulations under laboratory conditions. Additional testing and hazard assessments will be required to determine the feasibility of utilizing the proposed urine pretreatment formulations on ISS.

An Active Englacial Hydrological System in a Cold Glacier: Blood Falls, Taylor Glacier, Antarctica

NASA Astrophysics Data System (ADS)

Carr, C. G.; Pettit, E. C.; Carmichael, J.; Badgeley, J.; Tulaczyk, S. M.; Lyons, W. B.; Mikucki, J.

2016-12-01

Blood Falls is a supraglacial hydrological feature formed by episodic release of iron-rich subglacial brine derived from an extensive aquifer beneath the cold, polar, Taylor Glacier. While fluid transport in non-temperate ice typically occurs through meltwater delivery from the glacier surface to the bed (hydrofracturing, supraglacial lake drainage), Blood Falls represents the opposite situation: brine moves from a subglacial source to the glacier surface. Here, we present the first complete conceptual model for brine transport and release, as well as the first direct evidence of a wintertime brine release at Blood Falls obtained through year-round time-lapse photography. Related analyses show that brine pools subglacially underneath the northern terminus of Taylor Glacier, rather than flowing directly into proglacial Lake Bonney because ice-cored moraines and channelized surface topography provide hydraulic barriers. This pooled brine is pressurized by hydraulic head from the upglacier brine source region. Based on seismic data, we propose that episodic supraglacial release is initiated by high strain rates coupled with pressurized subglacial brine that drive intermittent subglacial and englacial fracturing. Ultimately, brine-filled basal crevasses propagate upward to link with surface crevasses, allowing brine to flow from the bed to the surface. The observation of wintertime brine release indicates that surface-generated meltwater is not necessary to trigger crack propagation or to maintain the conduit as previously suggested. The liquid brine persists beneath and within the cold ice (-17°C) despite ambient ice/brine temperature differences of as high as 10°C through both locally depressed brine freezing temperatures through cryoconcentration of salts and increased ice temperatures through release of latent heat during partial freezing of brine. The existence of an englacial hydrological system initiated by basal crevassing extends to polar glaciers a process thought limited to temperate glaciers and confirms that supraglacial, englacial, and subglacial hydrological systems act in concert to provide critical forcing on glacier dynamics, even in cold polar ice.

Management of surgically hypogonadal patients unable to take sex hormone replacement therapy.

PubMed

Nieman, Lynnette K

2003-06-01

Lifestyle changes in diet, exercise and the environment may help to prevent or ameliorate hot flashes and low bone density in men and women after surgical castration. Conventional medications, including megestrol acetate, SSRIs or clonidine, may improve hot flashes but may have limiting side effects. Some complementary and alternative approaches, including black cohosh, vitamin E, and soy products, work as well as placebo to decrease hot flashes and may be helpful, because they have low toxicity. Acupuncture and neurontin are promising but must be studied further. With regards to the prevention of osteoporosis and fractures in men and women, bisphosphonates are the most potent of the currently available agents; calcitonin is less effective. PTH has a large beneficial effect but is not yet available and is less well studied. In women, continued sexual intercourse and use of vaginal lubricants and moisturizers help to minimize symptoms of vaginal atrophy but do not ameliorate urinary symptoms. Low dose local estrogen treatment is a promising approach for the latter complaints.

Feasibility study of a brine boiling machine by solar energy

NASA Astrophysics Data System (ADS)

Phayom, W.

2018-06-01

This study presented the technical and operational feasibility of brine boiling machine by using solar energy instead of firewood or husk for salt production. The solar salt brine boiling machine consisted of a boiling chamber with an enhanced thermal efficiency through use of a solar brine heater. The stainless steel solar salt brine boiling chamber had dimensions of 60 cm x 70 cm x 20 cm. The steel brine heater had dimensions of 70 cm x 80 cm x 20 cm. The tilt angle of both the boiling chamber and brine heater was 20 degrees from horizontal. The brine temperature in the reservoir tank was 42°C with a flow rate of 6.64 L/h discharging into the solar boiling machine. It was found that the thermal efficiency and overall efficiency of the solar salt brine boiling machine were 0.63 and 0.38, respectively at a solar irradiance of 787.6 W/m2. The results shows that the potential of using solar energy for salt production system is feasible.

Evaluation of Brine Processing Technologies for Spacecraft Wastewater

NASA Technical Reports Server (NTRS)

Shaw, Hali L.; Flynn, Michael; Wisniewski, Richard; Lee, Jeffery; Jones, Harry; Delzeit, Lance; Shull, Sarah; Sargusingh, Miriam; Beeler, David; Howard, Jeanie;

CHRONIC DIETARY EXPOSURE WITH INTERMITTENT SPIKE DOSES OF CHLORPYRIFOS FAILS TO ALTER FLASH OR PATTERN REVERSAL EVOKED POTENTIALS IN RATS.

EPA Science Inventory

Human exposure to pesticides is often characterized by chronic low level exposure with intermittent spiked higher exposures. Visual disturbances are often reported following exposure to xenobiotics, and cholinesterase-inhibiting compounds have been reported to alter visual functi...

Metal-rich fluid inclusions provide new insights into unconformity-related U deposits (Athabasca Basin and Basement, Canada)

NASA Astrophysics Data System (ADS)

Richard, Antonin; Cathelineau, Michel; Boiron, Marie-Christine; Mercadier, Julien; Banks, David A.; Cuney, Michel

2016-02-01

The Paleoproterozoic Athabasca Basin (Canada) hosts numerous giant unconformity-related uranium deposits. The scope of this study is to establish the pressure, temperature, and composition (P-T-X conditions) of the brines that circulated at the base of the Athabasca Basin and in its crystalline basement before, during and after UO2 deposition. These brines are commonly sampled as fluid inclusions in quartz- and dolomite-cementing veins and breccias associated with alteration and U mineralization. Microthermometry and laser ablation-inductively coupled plasma-mass spectrometry (LA-ICP-MS) data from five deposits (Rabbit Lake, P-Patch, Eagle Point, Millennium, and Shea Creek) complement previously published data for the McArthur River deposit. In all of the deposits investigated, fluid inclusion salinity is between 25 and 40 wt.% NaCl equiv., with compositions displaying a continuum between a "NaCl-rich brine" end-member (Cl > Na > Ca > Mg > K) and a "CaCl2-rich brine" end-member (Cl > Ca ≈ Mg > Na > K). The CaCl2-rich brine has the highest salinity and shows evidence for halite saturation at the time of trapping. The continuum of compositions between the NaCl-rich brine and the CaCl2-rich brine end-members combined with P-T reconstructions suggest anisothermal mixing of the two brines (NaCl-rich brine, 180 ± 30 °C and 800 ± 400 bars; CaCl2-rich brine, 120 ± 30 °C and 600 ± 300 bars) that occurred under fluctuating pressure conditions (hydrostatic to supra-hydrostatic). However, because the two brines were U bearing and therefore oxidized, brine mixing was probably not the driving force for UO2 deposition. Several scenarios are put forward to account for the Cl-Na-Ca-Mg-K composition of the brines, involving combinations of seawater evaporation, halite dissolution, mixing with a halite-dissolution brine, Mg/Ca exchange by dolomitization, Na/Ca exchange by albitization of plagioclase, Na/K exchange by albitization of K-feldspar, and Mg loss by Mg-rich alteration. Finally, the metal concentrations in the NaCl-rich and CaCl2-rich brines are among the highest recorded compared to present-day sedimentary formation waters and fluid inclusions from basin-hosted base metal deposits (up to 600 ppm U, 3000 ppm Mn, 4000 ppm Zn, 6000 ppm Cu, 8000 ppm Pb, and 10,000 ppm Fe). The CaCl2-rich brine carries up to one order of magnitude more metal than the NaCl-rich brine. Though the exact origin of major cations and metals of the two brines remains uncertain, their contrasting compositions indicate that the two brines had distinct flow paths and fluid-rock interactions. Large-scale circulation of the brines in the Athabasca Basin and Basement was therefore a key parameter for metal mobility (including U) and formation of unconformity-related U deposits.

Coiled Brine Recovery Assembly (CoBRA): A New Approach to Recovering Water from Wastewater Brines

NASA Technical Reports Server (NTRS)

Pensinger, Stuart J.

2015-01-01

Brine water recovery represents a current technology gap in water recycling for human spaceflight. The role of a brine processor is to take the concentrated discharge from a primary wastewater processor, called brine, and recover most of the remaining water from it. The current state-of-the-art primary processor is the ISS Urine Processor Assembly (UPA) that currently achieves 70% water recovery. Recent advancements in chemical pretreatments are expected to increase this to 85% in the near future. This is a welcome improvement, yet is still not high enough for deep space transit. Mission architecture studies indicate that at least 95% is necessary for a Mars mission, as an example. Brine water recovery is the technology that bridges the gap between 85% and 95%, and moves life support systems one step closer to full closure of the water loop. Several brine water recovery systems have been proposed for human spaceflight, most of them focused on solving two major problems: operation in a weightless environment, and management and containment of brine residual. Brine residual is the leftover byproduct of the brine recovery process, and is often a viscous, sticky paste, laden with crystallized solid particles. Due to the chemical pretreatments added to wastewater prior to distillation in a primary processor, these residuals are typically toxic, which further complicates matters. Isolation of crewmembers from these hazardous materials is paramount. The Coiled Brine Recovery Assembly (CoBRA) is a recently developed concept from the Johnson Space Center that offers solutions to these challenges. CoBRA is centered on a softgoods evaporator that enables a passive fill with brine, and regeneration by discharging liquid brine residual to a collection bag. This evaporator is meant to be lightweight, which allows it to be discarded along with the accumulated brine solids contained within it. This paper discusses design and development of a first CoBRA prototype, and reports initial test results.

Photocatalytic reduction of nitrate using titanium dioxide for regeneration of ion exchange brine.

PubMed

Yang, Ting; Doudrick, Kyle; Westerhoff, Paul

2013-03-01

Nitrate is often removed from groundwater by ion exchange (IX) before its use as drinking water. Accumulation of nitrate in IX brine reduces the efficiency of IX regeneration and the useful life of the regeneration brine. For the first time, we present a strategy to photocatalytically reduce nitrate in IX brine, thereby extending the use of the brine. Titanium dioxide (Evonik P90), acting as photocatalyst, reduced nitrate effectively in both synthetic brines and sulfate-removed IX brine when formic acid (FA) was used as the hole scavenger (i.e., electron donor) and the initial FA to nitrate molar ratio (IFNR) was 5.6. Increasing the NaCl level in the synthetic brine slowed the nitrate reduction rate without affecting by-product selectivity of ammonium and gaseous N species (e.g., N(2), N(2)O). In a non-modified IX brine, nitrate removal was greatly inhibited owing to the presence of sulfate, which competed with nitrate for active surface sites on P90 and induced aggregation of P90 nanoparticles. After removing sulfate through barium sulfate precipitation, nitrate was effectively reduced; approximately 3.6 × 10(24) photons were required to reduce each mole of nitrate to 83% N Gases and 17% NH(4)(+). To make optimum use of FA and control the residual FA level in treated brine, the IFNR was varied. High IFNRs (e.g., 4, 5.6) were found to be more efficient for nitrate reduction but left higher residual FA in brine. IX column tests were performed to investigate the impact of residual FA for brine reuse. The residual FA in the brine did not significantly affect the nitrate removal capacity of IX resins, and formate contamination of treated water could be eliminated by rinsing with one bed volume of fresh brine. Copyright © 2012 Elsevier Ltd. All rights reserved.

Carbon isotopic evidence for microbial control of carbon supply to Orca Basin at the seawater-brine interface

NASA Astrophysics Data System (ADS)

Shah, S. R.; Joye, S. B.; Brandes, J. A.; McNichol, A. P.

2013-05-01

Orca Basin, an intraslope basin on the Texas-Louisiana continental slope, hosts a hypersaline, anoxic brine in its lowermost 200 m in which limited microbial activity has been reported. This brine contains a large reservoir of reduced and aged carbon, and appears to be stable at decadal time scales: concentrations and isotopic composition of dissolved inorganic (DIC) and organic carbon (DOC) are similar to measurements made in the 1970s. Both DIC and DOC are more "aged" within the brine pool than in overlying water, and the isotopic contrast between brine carbon and seawater carbon is much greater for DIC than DOC. While the stable carbon isotopic composition of brine DIC points towards a combination of methane and organic carbon remineralization as its source, radiocarbon and box model results point to the brine interface as the major source region for DIC, allowing for only limited oxidation of methane diffusing upwards from sediments. This conclusion is consistent with previous studies that identify the seawater-brine interface as the focus of microbial activity associated with Orca Basin brine. Isotopic similarities between DIC and DOC suggest a different relationship between these two carbon reservoirs than is typically observed in deep ocean basins. Radiocarbon values implicate the seawater-brine interface region as the likely source region for DOC to the brine as well as DIC.

Lithium isotope geochemistry and origin of Canadian shield brines.

PubMed

Bottomley, D J; Chan, L H; Katz, A; Starinsky, A; Clark, I D

2003-01-01

Hypersaline calcium/chloride shield brines are ubiquitous in Canada and areas of northern Europe. The major questions relating to these fluids are the origin of the solutes and the concentration mechanism that led to their extreme salinity. Many chemical and isotopic tracers are used to solve these questions. For example, lithium isotope systematics have been used recently to support a marine origin for the Yellowknife shield brine (Northwest Territories). While having important chemical similarities to the Yellowknife brine, shield brines from the Sudbury/Elliot Lake (Ontario) and Thompson/Snow Lake (Manitoba) regions, which are the focus of this study, exhibit contrasting lithium behavior. Brine from the Sudbury Victor mine has lithium concentrations that closely follow the sea water lithium-bromine concentration trajectory, as well as delta6Li values of approximately -28/1000. This indicates that the lithium in this brine is predominantly marine in origin with a relatively minor component of crustal lithium leached from the host rocks. In contrast, the Thompson/Snow Lake brine has anomalously low lithium concentrations, indicating that it has largely been removed from solution by alteration minerals. Furthermore, brine and nonbrine mine waters at the Thompson mine have large delta6Li variations of approximately 30/1000, which primarily reflects mixing between deep brine with delta6Li of -35 +/- 2/1000 and near surface mine water that has derived higher delta6Li values through interactions with their host rocks. The contrary behavior of lithium in these two brines shows that, in systems where it has behaved conservatively, lithium isotopes can distinguish brines derived from marine sources.

Electrically Conducting, Ca-Rich Brines, Rather Than Water, Expected in the Martian Subsurface

NASA Technical Reports Server (NTRS)

Burt, D. M.; Knauth, L. P.

2003-01-01

If Mars ever possessed a salty liquid hydrosphere, which later partly evaporated and froze down, then any aqueous fluids left near the surface could have evolved to become dense eutectic brines. Eutectic brines, by definition, are the last to freeze and the first to melt. If CaC12-rich, such brines can remain liquid until temperatures below 220 K, close to the average surface temperature of Mars. In the Martian subsurface, in intimate contact with the Ca-rich basaltic regolith, NaC1-rich early brines should have reacted to become Ca-rich. Fractional crystallization (freezing) and partial melting would also drive brines toward CaC12-rich compositions. In other words, eutectic brine compositions could be present in the shallow subsurface of Mars, for the same reasons that eutectic magma compositions are common on Earth. Don Juan Pond, Antarctica, a CaC12-rich eutectic brine, provides a possible terrestrial analog, particularly because it is fed from a basaltic aquifer. Owing to their relative density and fluid nature, brines in the Martian regolith should eventually become sandwiched between ice above and salts beneath. A thawing brine sandwich provides one explanation (among many) for the young gullies recently attributed to seepage of liquid water on Mars. Whether or not brine seepage explains the gullies phenomenon, dense, CaC12-rich brines are to be expected in the deep subsurface of Mars, although they might be somewhat diluted (temperatures permitting) and of variable salt composition. In any case, they should be good conductors of electricity.

Enlarged temporal integration window in schizophrenia indicated by the double-flash illusion.

PubMed

Haß, Katharina; Sinke, Christopher; Reese, Tanya; Roy, Mandy; Wiswede, Daniel; Dillo, Wolfgang; Oranje, Bob; Szycik, Gregor R

2017-03-01

In the present study we were interested in the processing of audio-visual integration in schizophrenia compared to healthy controls. The amount of sound-induced double-flash illusions served as an indicator of audio-visual integration. We expected an altered integration as well as a different window of temporal integration for patients. Fifteen schizophrenia patients and 15 healthy volunteers matched for age and gender were included in this study. We used stimuli with eight different temporal delays (stimulus onset asynchronys (SOAs) 25, 50, 75, 100, 125, 150, 200 and 300 ms) to induce a double-flash illusion. Group differences and the widths of temporal integration windows were calculated on percentages of reported double-flash illusions. Patients showed significantly more illusions (ca. 36-44% vs. 9-16% in control subjects) for SOAs 150-300. The temporal integration window for control participants went from SOAs 25 to 200 whereas for patients integration was found across all included temporal delays. We found no significant relationship between the amount of illusions and either illness severity, chlorpromazine equivalent doses or duration of illness in patients. Our results are interpreted in favour of an enlarged temporal integration window for audio-visual stimuli in schizophrenia patients, which is consistent with previous research.

REFUSE OF FERMENTATION BRINES IN THE CUCUMBER PICKLING INDUSTRY

EPA Science Inventory

The project evaluated on a commercial scale the technological and economic feasibility of recycling spent cucumber fermentation brine. Two brine treatment procedures, heat treatment and chemical treatment, were used. The results showed that brine recycling was practical on a comm...

Possible Mars brines - Equilibrium and kinetic considerations

NASA Technical Reports Server (NTRS)

Zent, A. P.; Fanale, F. P.

1986-01-01

To determine the fate of postulated near surface brines on Mars, the rate of H2O mass loss from subsurface brines was calculated as a function of latitude, depth, regolith porosity, eutectic temperature, and pore size. A model for a chemically reasonable brine that could reproduce Martian radar results was developed, and the escape rate of H2O molecules from such a brine was estimated. It is suggested that the presence of a low-permeability duricrust may be required to preserve such a brine for reasonable periods, and to prevent detection of an extensive subsurface system by the Viking MAWD instrument.

"Tepid" Geysers above salt caverns

NASA Astrophysics Data System (ADS)

Bérest, Pierre; Brouard, Benoît; Zakharov, Vassily

2018-06-01

The formation of a brine geyser erupting from the wellhead of a large underground salt cavern is described. In most cases, the brine outflow from an opened cavern is slow; it results from the cavern creep closure and the thermal expansion of the cavern brine. These two processes are smooth; however, the brine outflow often is bumpy, as it is modulated by atmospheric pressure variations that generate an elastic increase (or decrease) of both cavern and brine volumes. In addition, when the flow is fast enough, the brine thermodynamic behavior in the wellbore is adiabatic. The cold brine expelled from the cavern wellhead is substituted with warm brine entering the borehole bottom, resulting in a lighter brine column. The brine outflow increases. In some cases, the flow becomes so fast that inertia terms must be taken into account. A geyser forms, coming to an end when the pressure in the cavern has dropped sufficiently. A better picture is obtained when head losses are considered. A closed-form solution can be reached. This proves that two cases must be distinguished, depending on whether the cold brine initially contained in the wellbore is expelled fully or not. It can also be shown that geyser formation is a rare event, as it requires both that the wellbore be narrow and that the cavern be very compressible. This study stemmed from an actual example in which a geyser was observed. However, scarce information is available, making any definite interpretation difficult. xml:lang="fr"

Effects of the West Desert Pumping Project on Near-Surface Brine Resources in the Newfoundland Basin, Tooele and Box Elder Counties, Utah

NASA Astrophysics Data System (ADS)

White, W. W.; Jones, B. F.; Kohler, J. F.

2006-12-01

The Bureau of Land Management and U.S. Geological Survey have identified changes in Newfoundland Basin shallow-brine aquifer chemistry that resulted from pumping Great Salt Lake brine into the Newfoundland Evaporation Basin during the West Desert pumping project. The pumping project was operated by the State of Utah from April 1987, to June 1989 in an attempt to lower the historically high level of Great Salt Lake (pond elevation was 4,211.85 feet in 1986). Effects of the pumping on the Newfoundland Basin included altering the chemical character of the shallow brine aquifer by mixing two chemically different brines, and depositing a halite salt crust where none was previously reported on the lacustrine sediments of the Newfoundland Basin playa. The halite salt crust resulted from evaporation of the brine pond generated by the pumping project. Changes in the shallow-brine aquifer chemistry were determined by comparing pre-pumping brine chemistry with that of post pumping brine, and examining variation with borehole depth and location (i.e., playa periphery vs central basin topographic low) of specific analyte concentration profiles and solid-phase mineral assemblages obtained from analyses of core sample pore water and mineralogy. Brine sample analyses from 72 exploratory boreholes drilled in the Newfoundland Basin by Reynolds Metals Company during the mid 1960's provided pre-pumping brine chemistry. Post pumping chemistry was obtained from analyses of brine samples from 24 boreholes hand-augured between 1998 and 2001 in the central and peripheral portions of the Newfoundland Basin. TEQUIL, a brine equilibrium model, was used to better understand how the Great Salt Lake brines introduced into the Newfoundland Basin may have interacted with fluids contained within the Basin's shallow-brine aquifer. TEQUIL identified the sequence of mineral precipitation from evaporation of pre and post-pumping Newfoundland Basin shallow-aquifer fluids and Great Salt Lake brine. The model was also used to simulate 50-50 mixing of Great Salt Lake brine with pre-pumping Newfoundland Basin shallow-aquifer. The resulting precipitated mineral suite from sequential evaporation of the simulated brine mix was nearly identical to that from TEQUIL simulation of the post-pumping Newfoundland Basin brine. This differed from the mineral suite precipitated from the pre-pumping Newfoundland Basin brine. Examination of pore water chemistry and solid-phase mineralogy from borehole core samples taken from the playa periphery to the basin topographic low illustrate the following chemical and mineralogical generalities. At peripheral sites, magnesium and potassium concentrations decreased to near constant values below 0.5% at depths greater than 5 feet below the surface. Sulfate at similar depth ranged from 0.5 to 2% in peripheral areas. However, near the topographic low, sulfate reached 4.5% below the thickest salt crust at depths of about 3 feet, and then, along with magnesium and potassium, decreased to less than 1+ or 2% near the surface. In contrast, sulfate concentration in intermediate areas with thin salt crust, peaked near the surface but, magnesium and potassium concentrations peaked at depth. This suggests that the most recent salts precipitated from re-solution brine (generated from dissolution of halite salt crust by rain) were depleted with respect to magnesium and potassium, as compared to the deeper groundwater residuals from ancient Lake Bonneville.

The circulation of the Dead Sea brine in the regional aquifer

NASA Astrophysics Data System (ADS)

Weber, Nurit; Yechieli, Yoseph; Stein, Mordechai; Yokochi, Reika; Gavrieli, Ittai; Zappala, Jake; Mueller, Peter; Lazar, Boaz

2018-07-01

Ca-chloride brines have circulated between the lakes and the adjacent aquifers throughout the history of the Dead Sea lacustrine-hydrology system. The Ein-Qedem (EQ) hydrothermal saline springs system discharging at the western shores of the modern Dead Sea is the modern manifestation of this essential and continuous process. The EQ springs comprise the most significant source of Ca-chloride brine that currently discharges into the lake. The chemical composition of EQ brine has remained virtually uniform during the past ca. 40 yr, indicating that the brine represents a large groundwater reservoir. The EQ brine evolved from ancient Ca-chloride brine that occupied the tectonic depression of the Dead Sea Basin during the Quaternary. During this period, the composition of lake's brine was affected by mixing with freshwater and formation of primary minerals. Based on chronological and geochemical data, we argue that the EQ brine comprises the epilimnetic solution of last glacial Lake Lisan that penetrated and circulated through the adjacent Judea Group aquifer. 14C and 81Kr dating indicates recharge ages spanning the time interval of ∼40-20 ka, coinciding with the period when the lake reached its highest stand (of ∼ 200 ± 30 m below msl, at ∼31-17.4 ka) and maintained a stable layered (stratified) configuration for a period of several ten thousand years. The presented evidence suggests that the circulation of the Ca-chloride brine involves penetration into the aquifer during high stands (EQ brine recharge) and its discharge back into the lake during the modern low stands (∼400 to 430 m below msl). Accordingly, the mechanism of brine circulation between the lake and the marginal aquifers is related to the long-term hydro-climate history of the Dead Sea basin and its vicinity.

Protein removal from waste brines generated during ham salting through acidification and centrifugation.

PubMed

Gutiérrez-Martínez, Maria del Rosario; Muñoz-Guerrero, Hernán; Alcaína-Miranda, Maria Isabel; Barat, José Manuel

2014-03-01

The salting step in food processes implies the production of large quantities of waste brines, having high organic load, high conductivity, and other pollutants with high oxygen demand. Direct disposal of the residual brine implies salinization of soil and eutrophication of water. Since most of the organic load of the waste brines comes from proteins leaked from the salted product, precipitation of dissolved proteins by acidification and removal by centrifugation is an operation to be used in waste brine cleaning. The aim of this study is optimizing the conditions for carrying out the separation of proteins from waste brines generated in the pork ham salting operation, by studying the influence of pH, centrifugal force, and centrifugation time. Models for determining the removal of proteins depending on the pH, centrifugal force, and time were obtained. The results showed a high efficacy of the proposed treatment for removing proteins, suggesting that this method could be used for waste brine protein removal. The best pH value to be used in an industrial process seems to be 3, while the obtained results indicate that almost 90% of the proteins from the brine can be removed by acidification followed by centrifugation. A further protein removal from the brine should have to be achieved using filtrating techniques, which efficiency could be highly improved as a consequence of the previous treatment through acidification and centrifugation. Waste brines from meat salting have high organic load and electrical conductivity. Proteins can be removed from the waste brine by acidification and centrifugation. The total protein removal can be up to 90% of the initial content of the waste brine. Protein removal is highly dependent on pH, centrifugation rate, and time. © 2014 Institute of Food Technologists®

Improved Rare Earth Element Sorption from Simulated Geothermal Brines: Effect of Gassed versus Degassed Brines

DOE Data Explorer

Dean Stull

2016-05-24

A study exploring sorption and stripping characteristics of sorption media when simulated geothermal brines are degassed or not degassed. Experiments were done at 70°C. The brines used in this study were formulated by Tusaar. The two brines used/simulated are labeled 1M and 1CF. The data consists of a Word file explaining the results and an Excel file of the data.

Zeta potential in oil-brine-sandstone system and its role in oil recovery during controlled salinity waterflooding

NASA Astrophysics Data System (ADS)

Li, S.; Jackson, M.

2017-12-01

Wettability alteration is widely recognised as a primary role in improved oil recovery (IOR) during controlled salinity waterflooding (CSW) by modifying brine composition. The change of wettability of core sample depends on adsorption of polar oil compounds into the mineral surface which influences its surface charge density and zeta potential. It has been proved that zeta potentials can be useful to quantify the wettability and incremental oil recovery in natural carbonates. However, the study of zeta potential in oil-brine-sandstone system has not investigated yet. In this experimental study, the zeta potential is used to examine the controlled salinity effects on IOR in nature sandstone (Doddington) aged with two types of crude oils (Oil T and Oil D) over 4 weeks at 80 °C. Results show that the zeta potential measured in the Oil T-brine-sandstone system following primary waterflooding decreases compared to that in fully water saturation, which is consistent with the negative oil found in carbonates study, and IOR response during secondary waterflooding using diluted seawater was observed. In the case of negative oil, the injected low salinity brine induces a more repulsive electrostatic force between the mineral-brine interface and oil-brine interface, which results in an increase disjoining pressure and alters the rock surface to be more water-wet. For Oil D with a positive oil-brine interface, the zeta potential becomes more positive compared to that under single phase condition. The conventional waterflooding fails to observe the IOR in Oil D-brine-sandstone system due to a less repulsive electrostatic force built up between the two interfaces. After switching the injection brine from low salinity brine to formation brine, the IOR was observed. Measured zeta potentials shed some light on the mechanism of wettability alteration in the oil-brine-sandstone system and oil recovery during CSW.

Characterisation of flash X-ray source generated by Kali-1000 Pulse Power System

NASA Astrophysics Data System (ADS)

Satyanarayana, N.; Durga Prasada Rao, A.; Mittal, K. C.

2016-02-01

The electron beam-driven Rod Pinch Diode (RPD) is presently fielded on KALI-1000 Pulse Power System at Bhabha Atomic Research Centre, Visakhapatnam and is a leading candidate for future flash X-ray radiographic sources. The diode is capable of producing less than 2-mm radiation spot sizes and greater than 350 milli rads of dose measured at 1 m from the X-ray source. KALI-1000 Pulse Power Source is capable of delivering up to 600 kV using a Tesla Transformer with Demineralized Insulated Transmission Line (DITL), the diode typically operates between 250-330 kV . Since the radiation dose has a power-law dependence on diode voltage, this limits the dose production on KALI-1000 system. Radiation dose with angular variation is measured using thermoluminescent detectors (TLD's) and the X-ray spot size is measured using pin hole arrangement with image plate (IP) to obtain the time-integrated source profile as well as a time-resolved spot diagnostic. An X-ray pinhole camera was used to pick out where the energetic e-beam connects to the anode. Ideally the diode should function such that the radiation is emitted from the tip. The camera was mounted perpendicular to the machine's axis to view the radiation from the tip. Comparison of the spot sizes of the X-ray sources obtained by the pin hole and rolled edge arrangements was carried and results obtained by both the techniques are with in ± 10% of the average values.

7 CFR 58.320 - Brine tanks.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 3 2010-01-01 2010-01-01 false Brine tanks. 58.320 Section 58.320 Agriculture....320 Brine tanks. Brine tanks used for the treating of parchment liners shall be constructed of... liners. The tank should also be provided with a satisfactory drainage outlet. ...

7 CFR 58.320 - Brine tanks.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 7 Agriculture 3 2013-01-01 2013-01-01 false Brine tanks. 58.320 Section 58.320 Agriculture....320 Brine tanks. Brine tanks used for the treating of parchment liners shall be constructed of... liners. The tank should also be provided with a satisfactory drainage outlet. ...

7 CFR 58.320 - Brine tanks.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 3 2011-01-01 2011-01-01 false Brine tanks. 58.320 Section 58.320 Agriculture....320 Brine tanks. Brine tanks used for the treating of parchment liners shall be constructed of... liners. The tank should also be provided with a satisfactory drainage outlet. ...

7 CFR 58.320 - Brine tanks.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 7 Agriculture 3 2012-01-01 2012-01-01 false Brine tanks. 58.320 Section 58.320 Agriculture....320 Brine tanks. Brine tanks used for the treating of parchment liners shall be constructed of... liners. The tank should also be provided with a satisfactory drainage outlet. ...

7 CFR 58.320 - Brine tanks.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 7 Agriculture 3 2014-01-01 2014-01-01 false Brine tanks. 58.320 Section 58.320 Agriculture....320 Brine tanks. Brine tanks used for the treating of parchment liners shall be constructed of... liners. The tank should also be provided with a satisfactory drainage outlet. ...

Evaluation of cytotoxic, analgesic, antidiarrheal and phytochemical properties of Hygrophila spinosa (T. Anders) whole plant.

PubMed

Bellah, S M Faysal; Islam, Md Nur; Karim, Md Rezaul; Rahaman, Md Masudur; Nasrin, Mst Samima; Rahman, Md Atiar; Reza, A S M Ali

2017-03-01

Synthetic drugs are going to be replaced by plant-derived traditional drugs due to their cost effectiveness, relatively less harmfulness, and efficacy against multidrug resistance organisms. Hygrophila spinosa (Acanthaceae) has been used in a wide range of ailments including flatulence, diarrhea, dysentery, gonorrhea, and menorrhagia. Therefore, we investigated the cytotoxic, antinociceptive, and antidiarrheal effects of H. spinosa ethanol extract (EExHs). Preliminary phytochemical screening was accomplished by established methods modified in experimental protocol. EExHs was undertaken for cytotoxic assay by Brine shrimp lethality bioassay, antinociceptive action by acetic acid induced writhing test, and antidiarrheal activity by castor oil induced antidiarrheal test. Data were analyzed by GraphPad Prism 6.0 software using Dunnett's test for multiple comparisons. Reducing sugar, steroid, glycoside, tannin, alkaloid, saponins, and flavonoids were found to be present in EExHs. Lethal concentration (LC50) of EExHs for brine shrimps was 50.59 µg/mL which was relatively lower than that of the standard drug vincristine sulfate. In acetic acid induced writhing test, oral administration of EExHs at three different doses (125, 250, and 500 mg/kg) decreased writhing in dose-dependent manner while the highest dose (500 mg/kg) achieved the maximum percentages of pain inhibition (58.8%). Diclofenac sodium (25 mg/kg) was used as a reference antinociceptive drug. The antidiarrheal action of EExHs was not found to be very promising for further use; however, the pure compounds from EExHs could be analyzed to justify the effects. This research demonstrates that the secondary metabolites guided cytotoxic and analgesic effects could be extensively studied in multiple models to confirm the effects.

Long term exposure to low dose neurotoxic pesticides affects hatching, viability and cholinesterase activity of Artemia sp.

PubMed

Gambardella, Chiara; Nichino, Daniela; Iacometti, Camillo; Ferrando, Sara; Falugi, Carla; Faimali, Marco

2018-03-01

The brine shrimp Artemia was used as a model organism to test toxicity of several neuroactive pesticides (chlorpyrifos (CLP), chlorpyrifos oxon (CLP ox), diazinon (DZN), carbaryl (CBR)) following exposure to far below than lethal doses. Cysts were exposed to the pesticides in order to test a scenario similar to actual coastal environment contamination, by analyzing different responses. Cysts were rehydrated in water containing the pesticides at concentrations ranging from 10 -11 to 10 -5  M, for 72, 96 and 192 h, respectively. For these exposure times, morpho-functional and biochemical parameters, such as hatching speed and viability were investigated in the larvae together with cholinesterase (ChE) activity quantification and histochemical localization. Finally, ChE inhibition was also compared with conventional selective ChE inhibitors. Results showed that CLP ox and CBR caused a significant dose-dependent decrease in hatching speed, followed by high percentages of larval death, while CLP and DZN were responsible for irregular hatching patterns. In addition, the pesticides mostly caused larval death some days post-hatching, whereas this effect was negligible for the specific ChE inhibitors, suggesting that part of pesticide toxicity may be due to molecules other than the primary target. ChE activity was observed in the protocerebrum lobes, linked to the development of pair eyes. Such activity was inhibited in larvae exposed to all pesticides. When compared to conventional selective inhibitors of ChE activities, this inhibition demonstrated that the selected pesticides mainly affect acetylcholinesterase and, to a lesser extent, pseudocholinesterases. In conclusion, the brine shrimp is a good model to test the environmental toxicity of long term exposure to cholinergic pesticides, since changes in hatching speed, viability and ChE activity were observed. Copyright © 2018 Elsevier B.V. All rights reserved.

The evaporation path of seawater and the coprecipitation of Br- and K+ with halite

NASA Technical Reports Server (NTRS)

McCaffrey, M. A.; Lazar, B.; Holland, H. D.

1987-01-01

Brines and salt were sampled at the Morton Bahamas solar salt production facility on Great Inagua Island in the Bahamas. The brines were analyzed by ion chromatography to define more precisely than heretofore the evaporation path of seawater to the end of the halite facies. At Inagua, calcium carbonate begins to precipitate at a brine concentration factor of 1.8 times that of seawater. Gypsum begins to precipitate at a brine concentration of 3.8 times seawater, and halite at a concentration factor of 10.6. Three of the most concentrated brines from Inagua (40 times seawater) were evaporated further in the laboratory. Magnesium sulfate first precipitated at brine concentrations about 70 times those of seawater, and potassium-bearing phases began to precipitate for these brines at concentrations greater than 90 times those of seawater. The distribution of coefficients of Br- and K+ between brines and halite were determined by combining analytical data for the Inagua brines with measurements of the Br- and K+ content of halites from Inagua and of halite which had precipitated from Inagua brines during storage. The observed average value of DBr- is 0.032, in good agreement with some of the previous measurements. The measured values of DK+ are highly variable (0.001 to 0.021); DK+ for halite precipitated early in the halite facies is in the vicinity of 0.015.

Pre-injection brine production for managing pressure in compartmentalized CO₂ storage reservoirs

DOE PAGES

Buscheck, Thomas A.; White, Joshua A.; Chen, Mingjie; ...

2014-12-31

We present a reservoir management approach for geologic CO₂ storage that combines CO₂ injection with brine extraction. In our approach, dual-mode wells are initially used to extract formation brine and subsequently used to inject CO₂. These wells can also be used to monitor the subsurface during pre-injection brine extraction so that key data is acquired and analyzed prior to CO₂ injection. The relationship between pressure drawdown during pre-injection brine extraction and pressure buildup during CO₂ injection directly informs reservoir managers about CO₂ storage capacity. These data facilitate proactive reservoir management, and thus reduce costs and risks. The brine may bemore » used directly as make-up brine for nearby reservoir operations; it can also be desalinated and/or treated for a variety of beneficial uses.« less

Direct contact, binary fluid geothermal boiler

DOEpatents

Rapier, Pascal M.

1982-01-01

Energy is extracted from geothermal brines by direct contact with a working fluid such as isobutane which is immiscible with the brine in a geothermal boiler. The geothermal boiler provides a distributor arrangement which efficiently contacts geothermal brine with the isobutane in order to prevent the entrainment of geothermal brine in the isobutane vapor which is directed to a turbine. Accordingly the problem of brine carry-over through the turbine causes corrosion and scaling thereof is eliminated. Additionally the heat exchanger includes straightening vanes for preventing startup and other temporary fluctuations in the transitional zone of the boiler from causing brine carryover into the turbine. Also a screen is provided in the heat exchanger to coalesce the working fluid and to assist in defining the location of the transitional zone where the geothermal brine and the isobutane are initially mixed.

Direct contact, binary fluid geothermal boiler

DOEpatents

Rapier, P.M.

1979-12-27

Energy is extracted from geothermal brines by direct contact with a working fluid such as isobutane which is immiscible with the brine in a geothermal boiler. The geothermal boiler provides a distributor arrangement which efficiently contacts geothermal brine with the isobutane in order to prevent the entrainment of geothermal brine in the isobutane vapor which is directed to a turbine. Accordingly the problem of brine carryover through the turbine causing corrosion and scaling thereof is eliminated. Additionally the heat exchanger includes straightening vanes for preventing startup and other temporary fluctuations in the transitional zone of the boiler from causing brine carryover into the turbine. Also a screen is provided in the heat exchanger to coalesce the working fluid and to assist in defining the location of the transitional zone where the geothermal brine and the isobutane are initially mixed.

Oil exudation and histological structures of duck egg yolks during brining.

PubMed

Lai, K M; Chung, W H; Jao, C L; Hsu, K C

2010-04-01

Changes in oil exudation and histological structures of salted duck egg yolks during brining up to 5 wk were investigated. During brining, the salt contents of albumen, exterior yolk (hardened portion), and interior yolk (soft or liquid portion) gradually increased accompanied by slight decreases in moisture content. The hardening ratio of salted egg yolks increased rapidly to about 60% during the first week of brining and then reached 100% at the end of brining. After brining, part of the lipids in salted egg yolk became free due to the structural changes of low-density lipoprotein induced by dehydration and increase of salt content, and more free lipids in salted egg yolk were released after the cooking process. With the brining time increased up to 5 wk, the outer region of the cooked salted yolk gradually changed into dark brown, brown, orange, and then dark brown, whereas the center region changed into light yellow, yellow, dark yellow, and then yellow again. The microstructures of cooked salted egg yolks showed that the yolk spheres in the outer and middle regions retained their original shape, with some shrinking and being packed more loosely when brining time increased, and the exuded oil filled the space between the spheres. Furthermore, the yolk spheres in the center region transformed to a round shape but still showed granulation after 4 wk of brining, whereas they were mostly disrupted after 2 to 5 wk of brining. One of the most important characteristics of cooked salted egg yolks, gritty texture, contributed to oil exudation and granulated yolk spheres were observed at the brining time of 4 wk.

Registration of X-rays at 2500 m altitude in association with lightning flashes and thunderstorms

NASA Astrophysics Data System (ADS)

Montanyà, Joan; Fabró, Ferran; van der Velde, Oscar; Romero, David; Solà, Gloria; Hermoso, Juan Ramon; Soula, Serge; Williams, Earle R.; Pineda, Nicolau

2014-02-01

Electric fields and high-energy radiation of natural lightning measured at close range from a mountaintop tower are discussed. In none of the 12 negative cloud-to-ground upward flashes were X-rays observed. Also no energetic radiation was found in one negative upward leader at close range (20 m). In the first of two consecutive negative cloud-to-ground flashes, X-rays were detected during the last 1.75 ms of the leader. During the time of energetic radiation in the flash an intense burst of intracloud VHF sources was located by the interferometers. The X-ray production is attributed to the high electric field runaway electron mechanism during leader stepping. Even though the second flash struck closer than the previous one, no X-rays were detected. The absence of energetic radiation is attributed to being outside of the beam of X-ray photons from the leader tip or to the stepping process not allowing sufficiently intense electric fields ahead of the leader tip. High-speed video of downward negative leaders at the time when X-rays are commonly detected on the ground revealed the increase of speed and luminosity of the leader. Both phenomena allow higher electric fields at the leader front favoring energetic radiation. Background radiation was also measured during thunderstorms. The count rate of a particular day is presented and discussed. The increases in the radiation count rate are more coincident with radar reflectivity levels above 30 dBZ than with the total lightning activity close to the site. The increases of dose are attributed to radon daughter-ion precipitation.

WE-FG-202-01: Early Prediction of Radiotherapy Induced Skin Reactions Using Dynamic Infrared Imaging

DOE Office of Scientific and Technical Information (OSTI.GOV)

Biswal, N; Cifter, G; Sun, J

Purpose: To predict radiotherapy induced skin reactions using dynamic infrared imaging. Methods: Thermal images were captured by our homebuilt system consisting of two flash lamps and an infrared (IR) camera. The surface temperature of the skin was first raised by ∼ 6 oC from ∼1 ms flashes. The camera then captured a series of IR images for 10 seconds. For each image, a baseline skin temperature was recorded for 0.5sec before heat impulse. The temporal temperature gradients were calculated between a reference point (immediately after the flash) and at a time point 9sec after that. Thermal effusivity, an intrinsic thermalmore » property of a material, was calculated from the surface temperature decay of skin. We present experimental data in five patients undergoing radiation therapy, of which 2 were Head & Neck, 1 was Sarcoma and 2 were Breast cancer patients. The prescribed doses were 45 – 60 Gy in 25 – 30 fractions. Each patient was imaged before treatment and after every fifth fraction until end of the treatment course. An area on the skin, outside the radiation field, was imaged as control region. During imaging, each patient’s irradiated skins were scored based on RTOG skin morbidity scoring criteria. Results: Temperature gradient, which is the temperature recovery rate, depends on the thermal properties of underlying tissue. It was observed that, the skin temperature and temporal temperature gradient increases with delivered radiation dose and skin RTOG score. The treatment does not change effusivity of superficial skin layer, however there was a significant difference in effusivity between treated and control areas at depth of ∼ 1.5 – 1.8 mm, increases with dose. Conclusion: The higher temporal temperature gradient and effusivity from irradiated areas suggest that there is more fluid under the irradiated skin, which causes faster temperature recovery. The mentioned effects may be predictors of Moist Desquamation.« less

Lithium Sorption from Simulated Geothermal Brine: Impact of pH, Temperature, and Brine Chemistry

DOE Data Explorer

Jay Renew

2016-02-06

Lithium sorption information from experiments. Data includes the effects of pH, temperature and brine chemistry on the sorption of Lithium from a simulated geothermal brine. The sorbent used in the experiments is "hydrothermally produced, Spinel-LiMn2O4". The sorbent was produced by Carus Corporation.

UNDERSTANDING AND MANAGING RISKS POSED BY BRINES CONTAINING DISSOLVED CARBON DIOXIDE

EPA Science Inventory

Geologic disposal of supercritical carbon dioxide in saline aquifers and depleted oil and gas fields will cause large volumes of brine to become saturated with dissolved CO₂ at concentrations of 50 g/l or more.  As CO₂ dissolves in brine, the brine de...

Distribution of Cathepsin D Activity between Lysosomes and a Soluble Fraction of Marinating Brine.

PubMed

Szymczak, Mariusz

2016-08-01

This paper is the first ever to describe the phenomenon of bimodal distribution of cathepsin D in the lysosomal and soluble fractions of brine left after herring marinating. Up to 2 times higher cathepsin D activity was observed in the lysosome fraction. Activity of cathepsin D in brine increased according to the logarithmic function during low frequency-high power ultrasounds treatment or according to the linear function after multiple freezing-thawing of brine. Activity enhancement was achieved only in the brine devoid of lipids and suspension. Study results show also that measurement of lysosomal cathepsin D activity in the marinating brine requires also determining cathepsin E activity. Decreasing pore size of microfilter from 2.7 to 0.3 μm significantly reduced the lysosome content in the brine. The presence of lysosomes and the possibility of their separation as well as the likely release of cathepsins shall be considered during industrial application of the marinating brine, as new cathepsins preparations in fish and meat technology. © 2016 Institute of Food Technologists®

Lithium brines: A global perspective: Chapter 14

USGS Publications Warehouse

Munk, LeeAnn; Hynek, Scott; Bradley, Dwight C.; Boutt, David; Labay, Keith A.; Jochens, Hillary; Verplanck, Philip L.; Hitzman, Murray W.

2016-01-01

Lithium is a critical and technologically important element that has widespread use, particularly in batteries for hybrid cars and portable electronic devices. Global demand for lithium has been on the rise since the mid-1900s and is projected to continue to increase. Lithium is found in three main deposit types: (1) pegmatites, (2) continental brines, and (3) hydrothermally altered clays. Continental brines provide approximately three-fourths of the world’s Li production due to their relatively low production cost. The Li-rich brine systems addressed here share six common characteristics that provide clues to deposit genesis while also serving as exploration guidelines. These are as follows: (1) arid climate; (2) closed basin containing a salar (salt crust), a salt lake, or both; (3) associated igneous and/or geothermal activity; (4) tectonically driven subsidence; (5) suitable lithium sources; and (6) sufficient time to concentrate brine. Two detailed case studies of Li-rich brines are presented; one on the longest produced lithium brine at Clayton Valley, Nevada, and the other on the world’s largest producing lithium brine at the Salar de Atacama, Chile.

Chemical and isotopic changes in Williston Basin brines during long-term oil production: An example from the Poplar dome, Montana

USGS Publications Warehouse

Peterman, Zell; Thamke, Joanna N.

2016-01-01

Brine samples were collected from 30 conventional oil wells producing mostly from the Charles Formation of the Madison Group in the East and Northwest Poplar oil fields on the Fort Peck Indian Reservation, Montana. Dissolved concentrations of major ions, trace metals, Sr isotopes, and stable isotopes (oxygen and hydrogen) were analyzed to compare with a brine contaminant that affected groundwater northeast of the town of Poplar. Two groups of brine compositions, designated group I and group II, are identified on the basis of chemistry and 87Sr/86Sr ratios. The solute chemistry and Sr isotopic composition of group I brines are consistent with long-term residency in Mississippian carbonate rocks, and brines similar to these contaminated the groundwater. Group II brines probably resided in clastic rocks younger than the Mississippian limestones before moving into the Poplar dome to replenish the long-term fluid extraction from the Charles Formation. Collapse of strata at the crest of the Poplar dome resulting from dissolution of Charles salt in the early Paleogene probably developed pathways for the ingress of group II brines from overlying clastic aquifers into the Charles reservoir. Such changes in brine chemistry associated with long-term oil production may be a widespread phenomenon in the Williston Basin.

Brine Pockets in the Icy Shell on Europa: Distribution, Chemistry, and Habitability

NASA Technical Reports Server (NTRS)

Zolotov, M. Yu; Shock, E. L.; Barr, A. C.; Pappalardo, R. T.

2004-01-01

On Earth, sea ice is rich in brine, salt, and gas inclusions that form through capturing of seawater during ice formation. Cooling of the ice over time leads to sequential freezing of captured sea-water, precipitation of salts, exsolution of gases, and formation of brine channels and pockets. Distribution and composition of brines in sea ice depend on the rate of ice formation, vertical temperature gradient, and the age of the ice. With aging, the abundance of brine pockets decreases through downward migration. De- spite low temperatures and elevated salinities, brines in sea ice provide a habitat for photosynthetic and chemosynthetic organisms. On Europa, brine pockets and channels could exist in the icy shell that may be from a few km to a few tens of km thick and is probably underlain by a water ocean. If the icy shell is relatively thick, convection could develop, affecting the temperature pattern in the ice. To predict the distribution and chemistry of brine pockets in the icy shell we have combined numerical models of the temperature distribution within a convecting shell, a model for oceanic chemistry, and a model for freezing of Europan oceanic water. Possible effects of brine and gas inclusions on ice rheology and tectonics are discussed.

Moisture variations in brine-salted pasta filata cheese.

PubMed

Kindstedt, P S

2001-01-01

A study was made of the moisture distribution in brine-salted pasta filata cheese. Brine-salted cheeses usually develop reasonably smooth and predictable gradients of decreasing moisture from center to surface, resulting from outward diffusion of moisture in response to inward diffusion of salt. However, patterns of moisture variation within brine-salted pasta filata cheeses, notably pizza cheese, are more variable and less predictable because of the peculiar conditions that occur when warm cheese is immersed in cold brine. In this study, cold brining resulted in less moisture loss from the cheese surface to the brine. Also it created substantial temperature gradients within the cheese, which persisted after brining and influenced the movement of moisture within the cheese independently of that caused by the inward diffusion of salt. Depending on brining conditions and age, pizza cheese may contain decreasing, increasing, or irregular gradients of moisture from center to surface, which may vary considerably at different locations within a single block. This complicates efforts to obtain representative samples for moisture and composition testing. Dicing the entire block into small (e.g., 1.5 cm) cubes and collecting a composite sample after thorough mixing may serve as a practical sampling approach for manufacturers and users of pizza cheese that have ready access to dicing equipment.

Preliminary Feasibility Testing of the BRIC Brine Water Recovery Concept

NASA Technical Reports Server (NTRS)

Callahan, Michael R.; Pensinger, Stuart; Pickering, Karen D.

2011-01-01

The Brine Residual In-Containment (BRIC) concept was developed as a new technology to recover water from spacecraft wastewater brines. Such capability is considered critical to closing the water loop and achieving a sustained human presence in space. The intention of the BRIC concept is to increase the robustness and efficiency of the dewatering process by performing drying inside the container used for the final disposal of the residual brine solid. Recent efforts in the development of BRIC have focused on preliminary feasibility testing using a laboratory- assembled pre-prototype unit. Observations of the drying behavior of actual brine solutions processed under BRIC-like conditions has been of particular interest. To date, experiments conducted with three types of analogue spacecraft wastewater brines have confirmed the basic premise behind the proposed application of in-place drying for these solutions. Specifically, the dried residual mass from these solutions have tended to exhibit characteristics of adhesion and flow that are expected to continue to challenge process stream management in spacecraft brine dewatering system designs. Yet, these same characteristics may favor the development of capillary- and surface-tension-based approaches envisioned as part of an ultimate microgravity-compatible BRIC design. In addition, preliminary feasibility testing of the BRIC pre-prototype confirmed that high rates of water recovery, up to 98% of the available brine water, may be possible while still removing the majority of the brine contaminants from the influent brine stream. These and other observations from testing are reported.

Mechanisms of phosphene generation in ocular proton therapy as related to space radiation exposure

NASA Astrophysics Data System (ADS)

Chuard, D.; Anthonipillai, V.; Dendale, R.; Nauraye, C.; Khan, E.; Mabit, C.; De Marzi, L.; Narici, L.

2016-08-01

Particle therapy provides an opportunity to study the human response to space radiation in ground-based facilities. On this basis, a study of light flashes analogous to astronauts' phosphenes reported by patients undergoing ocular proton therapy has been undertaken. The influence of treatment parameters on phosphene generation was investigated for 430 patients treated for a choroidal melanoma at the proton therapy centre of the Institut Curie (ICPO) in Orsay, France, between 2008 and 2011. 60% of them report light flashes, which are predominantly (74%) blue. An analysis of variables describing the patient's physiology, properties of the tumour and dose distribution shows that two groups of tumour and beam variables are correlated with phosphene occurrence. Physiology is found to have no influence on flash triggering. Detailed correlation study eventually suggests a possible twofold mechanism of phosphene generation based on (i) indirect Cerenkov light in the bulk of the eye due to nuclear interactions and radioactive decay and (ii) direct excitation of the nerve fibres in the back of the eye and/or radical excess near the retina.

Risk of high blood pressure in salt workers working near salt milling plants: A cross-sectional and interventional study

PubMed Central

Haldiya, Kripa Ram; Mathur, Murli Lal; Sachdev, Raman; Saiyed, Habibulla N

2005-01-01

Background Workers working close to salt milling plants may inhale salt particles floating in the air, leading to a rise in plasma sodium, which, in turn, may increase the blood pressure and the risk of hypertension. Methods To test the above hypothesis, occupational health check-up camps were organized near salt manufacturing units and all workers were invited for a free health examination. The workers who worked with dry salt in the vicinity of salt milling plants were defined as "non-brine workers," while those working in brine pans located far away from milling plants were defined as "brine workers." Blood pressure (BP) was measured during each clinical examination. In all, 474 non-brine workers and 284 brine workers were studied. Results Mean systolic blood pressure of non-brine workers (122.1 ± 13.3 mm Hg) was significantly higher than that of brine workers (118.8 ± 12.8 mm Hg, p < 0.01). Mean diastolic blood pressure of non-brine workers (71.5 ± 10.4 mm Hg) was significantly higher than that of brine workers (69.7 ± 9.4 mm Hg, p = 0.02). The prevalence of hypertension was significantly higher in non-brine workers (12.2%) than in brine workers (7.0%, p = 0.02). Nineteen salt workers were monitored while they used face masks and spectacles, for six days. Systolic, as well as diastolic, blood pressure of these workers began declining on the third day and continued to decline on the fourth day, but remained stationary up to the sixth day. The concentration of salt particles in the breathing zone of these workers was 376 mg/m3 air. Conclusion Inhalation of salt particles in non-brine workers may be an occupational cause of increased blood pressure. PMID:16042798

Origin and Evolution of Li-rich Brines at Clayton Valley, Nevada, USA

NASA Astrophysics Data System (ADS)

Munk, L. A.; Bradley, D. C.; Hynek, S. A.; Chamberlain, C. P.

2011-12-01

Lithium is the key component in Li-ion batteries which are the primary energy storage for electric/hybrid cars and most electronics. Lithium is also an element of major importance on a global scale because of interest in increasing reliance on alternative energy sources. Lithium brines and pegmatites are the primary and secondary sources, respectively of all produced Li. The only Li-brine in the USA that is currently in production exists in Clayton Valley, NV. The groundwater brines at Clayton Valley are located in a closed basin with an average evaporation rate of 142 cm/yr. The brines are pumped from six aquifer units that are composed of varying amounts of volcanic ash, gravel, salt, tufa, and fine-grained sediments. Samples collected include spring water, fresh groundwater, groundwater brine, and meteoric water (snow). The brines are classified as Na-Cl waters and the springs and fresh groundwater have a mixed composition and are more dilute than the brines. The Li content of the waters in Clayton Valley ranges from less than 1 μg/L (snow) up to 406.9 mg/L in the lower ash aquifer system (one of six aquifers in the basin). The cold springs surrounding Clayton Valley have Li concentrations of about 1 mg/L. A hot spring located just east of Clayton Valley contains 1.6 mg/L Li. The Li concentration of the fresh groundwater is less than 1 mg/L. Hot groundwater collected in the basin contain 30-40 mg/L Li. Water collected from a geothermal drilling north of Silver Peak, NV, had water with 4.9 mg/L Li at a depth of >1000m. The δD and δ18O isotopic signatures of fresh groundwater and brine form an evaporation path that extends from the global meteoric water line toward the brine from the salt aquifer system (the most isotopically enriched brine with ave. δD = -3.5, ave. δ18O = -67.0). This suggests that mixing of inflow water with the salt aquifer brine could have played an important role in the evolution of the brines. Along with mixing, evaporation appears to be an important process in the brine evolution. This is evident because of the increase in Na concentration as a function of enrichment in δD for most brine samples. In contrast the non-brine waters flowing into the basin show an increase in Na at relatively constant δD indicating little evaporation. The δD of clays sampled throughout a sediment core extending to 354 m below the surface show fluctuations that likely indicate warmer and cooler periods through time. Further investigation of the relationship of past climate and Li accumulation is in progress.

High-order noise analysis for low dose iterative image reconstruction methods: ASIR, IRIS, and MBAI

NASA Astrophysics Data System (ADS)

Do, Synho; Singh, Sarabjeet; Kalra, Mannudeep K.; Karl, W. Clem; Brady, Thomas J.; Pien, Homer

2011-03-01

Iterative reconstruction techniques (IRTs) has been shown to suppress noise significantly in low dose CT imaging. However, medical doctors hesitate to accept this new technology because visual impression of IRT images are different from full-dose filtered back-projection (FBP) images. Most common noise measurements such as the mean and standard deviation of homogeneous region in the image that do not provide sufficient characterization of noise statistics when probability density function becomes non-Gaussian. In this study, we measure L-moments of intensity values of images acquired at 10% of normal dose and reconstructed by IRT methods of two state-of-art clinical scanners (i.e., GE HDCT and Siemens DSCT flash) by keeping dosage level identical to each other. The high- and low-dose scans (i.e., 10% of high dose) were acquired from each scanner and L-moments of noise patches were calculated for the comparison.

Brine Extraction and Treatment Strategies to Enhance Pressure Management and Control of CO 2 Plumes in Deep Geologic Formations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Okwen, Roland; Frailey, Scott; Dastgheib, Seyed

The overall goal of the this project is to develop and validate pressure management and carbon dioxide (CO 2) plume control strategies that can address technical and economic barriers to commercial deployment of CO 2 storage technologies, based on computational and field demonstration work at the Archer Daniels Midland Company (ADM) facility where the Illinois Basin–Decatur Project (IBDP) and the Illinois-Industrial Carbon Capture and Storage (IL-ICCS) projects are located. To accomplish the overall goal, the ISGS designed a brine extraction storage test (BEST) that could be completed in two phases. The goal of BEST Phase I was to evaluate themore » feasibilities of extraction well(s) placement, the brine extraction to CO 2 injection rate ratio, extraction well completion, and brine treatment and handling. The goal of BEST Phase II would be to validate the brine extraction and treatment options deemed feasible in Phase I by (1) demonstrating the efficacy of brine extraction (BE) in managing pressure (i.e., formation) and the CO 2 plume, and (2) demonstrating treatment of extracted brine with high total dissolved solids (TDS; >200,000 mg/L) using multiple advanced treatment technologies. This report details work done in Phase I. Several brine extraction and treatment scenarios were tested, simulated, and analyzed for their effectiveness in extracting brine. Initially a vertical well was studied; however, geologic modeling, reservoir modeling, and the existing facility and wellbore infrastructure dictated that the location of a vertical brine extraction well was limited to an area with no existing monitoring wells and where the well would be in relative proximity to an existing CO 2 plume. Consequently, a vertical well was excluded, and a horizontal brine extraction well placed above the existing CO 2 plume near two existing wells was studied. The horizontal well option allows the project to leverage the availability of cased-hole logs and cross-well tomography to monitor CO 2 saturation and plume distribution, respectively. Because of the proximity of the horizontal well option to two existing wells, no additional monitoring well (or caprock penetration) is required. The recommended brine extraction pilot design options are (1) a horizontal extraction well at the base of the Middle Mt. Simon, which is 350–520 ft (107–158 m) above the CO 2 plume at CCS#1 and VW#1; or (2) a vertical extraction well 0.5 mi (0.8 km) from CCS#2 in a direction approximately southeast of CCS#2, perpendicular to the direction of high hydraulic connectivity. A horizontal extraction well has advantages over a vertical extraction well, including less risk of drilling into an existing CO 2 plume and it can be located between two other wells that can be used for monitoring. Thus, because the two existing wells can serve as monitoring wells, it eliminates the need for a third verification well and allows for a lower extraction rate to control the CO 2 plume and pressure. Managing pressure and the CO 2 plume distribution via brine extraction creates the obvious and important challenge of handling and treating the extracted brine. There were three options for brine disposal: (1) underground injection control (UIC) disposal well, (2) brine treatment and industrial use, and (3) brine pretreatment and discharge into municipal wastewater system. The primary design elements were budget and permitting requirements. The disposal well would be a vertical well drilled and completed into the Potosi Dolomite. For the range of extraction rates anticipated, the cost of this well is relatively constant. The cost of brine treatment is highly depends on the extraction rate, which depends on the well orientation. If relatively high rates are required, the vertical disposal well option is more favorable; for relatively lower rates, the two brine treatment options have lower costs. Life-cycle-analysis studies on extracted brine handling options suggest that a UIC well has a lower environmental impact than brine treatment. Both brine disposal options using brine treatment require removal of suspended solids from the extracted brine. The most suitable commercially available technology and the most promising emerging and innovative technology are recommended for implementation in Phase II. Though the challenges of this project are written specific to Decatur, every CO 2 storage site considering the use of brine extraction integrated with CO 2 storage will have similar, if not identical, technical and logistical challenges.« less

TREE Preferred Procedures, Selected Electronic Parts.

DTIC Science & Technology

1982-01-31

presented. Chapter 5 covers dosimetry and environmental correlation procedures. Neutron measurements, photon and electron measurements, and pulse...complications from nonuniformity of dose and to provide accurate dosimetry , exposures should be performed under conditions of electron equi- librium. Unless...nonconducting dosimetry materials or test articles are exposed to intense electron beams characteristic of flash X-ray machines, the effect of the potential

Two-brine model of the genesis of strata-bound Zechstein deposits (Kupferschiefer type), Poland

NASA Astrophysics Data System (ADS)

Kucha, H.; Pawlikowski, M.

1986-01-01

These Kupferschiefer deposits were probably formed as a result of a mixing of two brines. The upper cold brine (UCB) is an unmineralized brine rich in Na, Ca, Cl and SO4, with a pH>7 and originating from evaporites overlying the metal-bearing Zechstein rocks. The lower hot brine (LHB) rich in Mg, K, Cl, SO4 and CO3 with a pH<=7 formed in sediments in the central part of the Zechstein basin at a depth of 7,000 m. This brine was subjected to heating and upward convection toward the Fore-Sudetic monocline along the bottom of the Z1 carbonates. During its migration, it caused albitization, serpentinization and leaching of the primary metal deposits in rocks underlying the Zechstein becoming enriched in heavy metals. The mineralization process, being a result of the mixing of the two brines (UCB and LHB), and catalytic oxidation of the organic matter of the black shale were initiated at shallow depths in the area of the Fore-Sudetic monocline. The boundary of the two brines generally overlapped the strike of the black shale. Parts of the deposit with shale-free host rock suggest that the action of two brines alone was capable of producing economic concentrations of Cu, Pb and Zn. Where the boundary of the two brines overlaps the autooxidation zone (the black shale bottom) and also coincides with γ radiation of thucholite, concentrations of noble metals result. The characteristic vertical distribution of the triplet Cu→Pb→Zn from the bottom upward is universal in the Kupferschiefer environment.

Cost-effective bioregeneration of nitrate-laden ion exchange brine through deliberate bicarbonate incorporation.

PubMed

Li, Qi; Huang, Bin; Chen, Xin; Shi, Yi

2015-05-15

Bioregeneration of nitrate-laden ion exchange brine is desired to minimize its environmental impacts, but faces common challenges, i.e., enriching sufficient salt-tolerant denitrifying bacteria and stabilizing brine salinity and alkalinity for stable brine biotreatment and economically removing undesired organics derived in biotreatment. Incorporation of 0.25 M bicarbonate in 0.5 M chloride brine little affected resin regeneration but created a benign alkaline condition to favor bio-based brine regeneration. The first-quarter sulfate-mainly enriched spent brine (SB) was acidified with carbon source acetic acid for using CaCl2 at an efficiency >80% to remove sulfate. Residual Ca(2+) was limited below 2 mM by re-mixing the first-quarter and remained SB to favor denitrification. Under [Formula: see text] system buffered pH condition (8.3-8.8), nitrate was removed at 0.90 gN/L/d by hematite-enriched well-settled activated sludge (SVI 8.5 ml/g) and the biogenic alkalinity was retained as bicarbonate. The biogenic alkalinity met the need of alkalinity in removing residual Ca(2+) after sulfate removal and in CaCl2-induced CaCO3 flocculation to remove 63% of soluble organic carbon (SOC) in biotreated brine. Carbon-limited denitrification was also operated after activated sludge acclimation with sulfide to cut SOC formation during denitrification. Overall, this bicarbonate-incorporation approach, stabilizing the brine salinity and alkalinity for stable denitrification and economical removal of undesired SOC, suits long-term cost-effective brine bioregeneration. Copyright © 2015 Elsevier Ltd. All rights reserved.

Study of mixed mode fracture toughness and fracture trajectories in gypsum interlayers in corrosive environment

PubMed Central

Xiankai, Bao; Jinchang, Zhao

2018-01-01

Based on the engineering background of water dissolving mining for hydrocarbon storage in multi-laminated salt stratum, the mixed mode fracture toughness and fracture trajectory of gypsum interlayers soaked in half-saturated brine at various temperatures (20°C, 50°C and 80°C) were studied by using CSNBD (centrally straight-notched Brazilian disc) specimens with required inclination angles (0°, 7°, 15°, 22°, 30°, 45°, 60°, 75°, 90°) and SEM (scanning electron microscopy). The results showed: (i) The fracture load of gypsum specimens first decreased then increased with increasing inclination angle, due to the effect of friction coefficient. When soaked in brine, the fracture toughness of gypsum specimens gradually decreased with increasing brine temperature. (ii) When soaked in brine, the crystal boundaries of gypsum separated and became clearer, and the boundaries became more open between the crystals with increasing brine temperature. Besides, tensile micro-cracks appeared on the gypsum crystals when soaked in 50°C brine, and the intensity of tensile cracks became more severe when soaking in 80°C brine. (iii) The experimental fracture envelopes derived from the conventional fracture criteria and lay outside these conventional criteria. The experimental fracture envelopes were dependent on the brine temperature and gradually expanded outward as brine temperature increases. (iv) The size of FPZ (fracture process zone) was greatly dependent on the damage degree of materials and gradually increased with increase of brine temperature. The study has important implication for the control of shape and size of salt cavern. PMID:29410841

Evaluation of the Malaga Bend salinity alleviation project, Eddy County, New Mexico

USGS Publications Warehouse

Kunkler, J.L.

1980-01-01

In an effort to reduce the flow of brine springs in the Malaga Bend reach of the Pecos River in southeastern New Mexico, brine was pumped from an aquifer underlying the Malaga Bend reach to a local depression known as Anderson Lake. The attempt to improve the quality of river water with this experiment was not successful because brine leakage from Anderson Lake to the nearby Pecos River through permeable subsurface rocks was greater than the previous natural spring inflow. Brine leakage from Anderson Lake from July 22, 1963, through September 30, 1968, was estimated by evaporation-pan, salt accumulation, and dissolved-constituent methods. The leakage values given by these three methods are in good agreement with each other and indicate that between the dates given, leakage from the lake was about 2 ,300 acre-feet, compared with a brine inflow to the lake of about 3,690 acre-feet. Other data indicate that pumping from the brine aquifer greatly reduced the natural inflow from brine springs to the Malaga Bend reach. The rate of brine leakage from Anderson Lake is probably greater than might be expected from other brine lakes in the area because the cavities in the bottom of the lake apparently are in hydrologic connection with the Pecos River. This connection is shown by a relation between the salinity of the Pecos River and the reservoir stage of Anderson Lake. (USGS)

Ice Generation and the Heat and Mass Transfer Phenomena of Introducing Water to a Cold Bath of Brine.

PubMed

Yun, Xiao; Quarini, Giuseppe L

2017-03-13

We demonstrate a method for the study of the heat and mass transfer and of the freezing phenomena in a subcooled brine environment. Our experiment showed that, under the proper conditions, ice can be produced when water is introduced to a bath of cold brine. To make ice form, in addition to having the brine and water mix, the rate of heat transfer must bypass that of mass transfer. When water is introduced in the form of tiny droplets to the brine surface, the mode of heat and mass transfer is by diffusion. The buoyancy stops water from mixing with the brine underneath, but as the ice grows thicker, it slows down the rate of heat transfer, making ice more difficult to grow as a result. When water is introduced inside the brine in the form of a flow, a number of factors are found to influence how much ice can form. Brine temperature and concentration, which are the driving forces of heat and mass transfer, respectively, can affect the water-to-ice conversion ratio; lower bath temperatures and brine concentrations encourage more ice to form. The flow rheology, which can directly affect both the heat and mass transfer coefficients, is also a key factor. In addition, the flow rheology changes the area of contact of the flow with the bulk fluid.

Corrosion of iron by iodide-oxidizing bacteria isolated from brine in an iodine production facility.

PubMed

Wakai, Satoshi; Ito, Kimio; Iino, Takao; Tomoe, Yasuyoshi; Mori, Koji; Harayama, Shigeaki

2014-10-01

Elemental iodine is produced in Japan from underground brine (fossil salt water). Carbon steel pipes in an iodine production facility at Chiba, Japan, for brine conveyance were found to corrode more rapidly than those in other facilities. The corroding activity of iodide-containing brine from the facility was examined by immersing carbon steel coupons in "native" and "filter-sterilized" brine samples. The dissolution of iron from the coupons immersed in native brine was threefold to fourfold higher than that in the filter-sterilized brine. Denaturing gradient gel electrophoresis analyses revealed that iodide-oxidizing bacteria (IOBs) were predominant in the coupon-containing native brine samples. IOBs were also detected in a corrosion deposit on the inner surface of a corroded pipe. These results strongly suggested the involvement of IOBs in the corrosion of the carbon steel pipes. Of the six bacterial strains isolated from a brine sample, four were capable of oxidizing iodide ion (I(-)) into molecular iodine (I(2)), and these strains were further phylogenetically classified into two groups. The iron-corroding activity of each of the isolates from the two groups was examined. Both strains corroded iron in the presence of potassium iodide in a concentration-dependent manner. This is the first report providing direct evidence that IOBs are involved in iron corrosion. Further, possible mechanisms by which IOBs corrode iron are discussed.

Physical properties of NaCl-free cucumber fermentation cover brine containing calcium chloride and glycerin and apparent freezing injury of the brined fruits

USDA-ARS?s Scientific Manuscript database

Use of glycerin and calcium chloride to reduce the freezing point and improve quality of bulk stored fermented cucumbers brined without NaCl, was explored. The incidence of pre-freezing injury on the fruits, caused by deposition in tanks containing cushion brine prepared with 2.5% calcium chloride, ...

Integrated processes for desalination and salt production: A mini-review

NASA Astrophysics Data System (ADS)

Wenten, I. Gede; Ariono, Danu; Purwasasmita, Mubiar; Khoirudin

2017-03-01

The scarcity of fresh water due to the rapid growth of population and industrial activities has increased attention on desalination process as an alternative freshwater supply. In desalination process, a large volume of saline water is treated to produce freshwater while a concentrated brine is discharged back into the environment. The concentrated brine contains a high concentration of salt and also chemicals used during desalination operations. Due to environmental impacts arising from improper treatment of the brine and more rigorous regulations of the pollution control, many efforts have been devoted to minimize, treat, or reuse the rejected brine. One of the most promising alternatives for brine handling is reusing the brine which can reduce pollution, minimize waste volume, and recover valuable salt. Integration of desalination and salt production can be implemented to reuse the brine by recovering water and the valuable salts. The integrated processes can achieve zero liquid discharge, increase water recovery, and produce the profitable salt which can reduce the overall desalination cost. This paper gives an overview of desalination processes and the brine impacts. The integrated processes, including their progress and advantages in dual-purpose desalination and salt production are discussed.

Deep reaching fluid flow in the North East German Basin: origin and processes of groundwater salinisation

NASA Astrophysics Data System (ADS)

Tesmer, M.; Möller, P.; Wieland, S.; Jahnke, C.; Voigt, H.; Pekdeger, A.

2007-11-01

Major element chemistry, rare-earth element distribution, and H and O isotopes are conjointly used to study the sources of salinisation and interaquifer flow of saline groundwater in the North East German Basin. Chemical analyses from hydrocarbon exploration campaigns showed evidence of the existence of two different groups of brines: halite and halite Ca-Cl brines. Residual brines and leachates are identified by Br-/Cl- ratios. Most of the brines are dissolution brines of Permian evaporites. New analyses show that the pattern of rare-earth elements and yttrium (REY) are closely linked to H and O isotope distribution. Thermal brines from deep wells and artesian wells indicate isotopically evaporated brines, which chemically interacted with their aquifer environment. Isotopes and rare-earth element patterns prove that cross flow exists, especially in the post-Rupelian aquifer. However, even at depths exceeding 2,000 m, interaquifer flow takes place. The rare-earth element pattern and H and O isotopes identify locally ascending brines. A large-scale lateral groundwater flow has to be assumed because all pre-Rupelian aquifer systems to a depth of at least 500 m are isotopically characterised by Recent or Pleistocene recharge conditions.

Chlorate adsorption from chlor-alkali plant brine stream.

PubMed

Lakshmanan, Shyam; Murugesan, Thanabalan

2017-07-01

Chlorates are present in the brine stream purged from chlor-alkali plants. Tests were conducted using activated carbon from coconut shell, coal or palm kernel shell to adsorb chlorate. The results show varying levels of adsorption with reduction ranging between 1.3 g/L and 1.8 g/L. This was higher than the chlorate generation rate of that plant, recorded at 1.22 g/L, indicating that chlorate can be adequately removed by adsorption using activated carbon. Coconut based activated carbon exhibited the best adsorption of chlorate of the three types of activated carbon tested. Introducing an adsorption step prior to purging of the brine will be able to reduce chlorate content in the brine stream. The best location for introducing the adsorption step was identified to be after dechlorination of the brine and before resaturation. Introduction of such an adsorption step will enable complete recovery of the brine and prevent brine purging, which in turn will result in less release of chlorides and chlorates to the environment.

Thin liquid films in improved oil recovery from low-salinity brine

DOE PAGES

Myint, Philip C.; Firoozabadi, Abbas

2015-03-19

Low-salinity waterflooding is a relatively new method for improved oil recovery that has generated much interest. It is generally believed that low-salinity brine alters the wettability of oil reservoir rocks towards a wetting state that is optimal for recovery. The mechanism(s) by which the wettability alteration occurs is currently an unsettled issue. This study reviews recent studies on wettability alteration mechanisms that affect the interactions between the brine/oil and brine/rock interfaces of thin brine films that wet the surface of reservoir rocks. Of these mechanisms, we pay particular attention to double-layer expansion, which is closely tied to an increase inmore » the thickness and stability of the thin brine films. Our review examines studies on both sandstones and carbonate rocks. We conclude that the thin-brine-film mechanisms provide a good qualitative, though incomplete, picture of this very complicated problem. Finally, we give suggestions for future studies that may help provide a more quantitative and complete understanding of low-salinity waterflooding.« less

Delineation of brine contamination in and near the East Poplar oil field, Fort Peck Indian Reservation, northeastern Montana, 2004-09

USGS Publications Warehouse

Thamke, Joanna N.; Smith, Bruce D.

2014-01-01

The extent of brine contamination in the shallow aquifers in and near the East Poplar oil field is as much as 17.9 square miles and appears to be present throughout the entire saturated zone in contaminated areas. The brine contamination affects 15–37 billion gallons of groundwater. Brine contamination in the shallow aquifers east of the Poplar River generally moves to the southwest toward the river and then southward in the Poplar River valley. The likely source of brine contamination in the shallow aquifers is brine that is produced with crude oil in the East Poplar oil field study area. Brine contamination has not only affected the water quality from privately owned wells in and near the East Poplar oil field, but also the city of Poplar’s public water-supply wells. Three water-quality types characterize water in the shallow aquifers; a fourth water-quality type in the study area characterizes the brine. Type 1 is uncontaminated water that is suitable for most domestic purposes and typically contains sodium bicarbonate and sodium/magnesium sulfate as the dominant ions. Type 2 is moderately contaminated water that is suitable for some domestic purposes, but not used for drinking water, and typically contains sodium and chloride as the dominant ions. Type 3 is considerably contaminated water that is unsuitable for any domestic purpose and always contains sodium and chloride as the dominant ions. Type 3 quality of water in the shallow aquifers is similar to Type 4, which is the brine that is produced with crude oil. Electromagnetic apparent conductivity data were collected in the 106 square-mile area and used to determine extent of brine contamination. These data were collected and interpreted in conjunction with water-quality data collected through 2009 to delineate brine plumes in the shallow aquifers. Monitoring wells subsequently were drilled in some areas without existing water wells to confirm most of the delineated brine plumes; however, several possible plumes do not contain either existing water wells or monitoring wells. Analysis of groundwater samples from wells confirms the presence of 12.1 square miles of contamination, as much as 1.7 square miles of which is considerably contaminated (Type 3). Electromagnetic apparent conductivity data in areas with no wells delineate an additional 5.8 square miles of possible contamination, 2.1 square miles of which might be considerably contaminated (Type 3). Storage-tank facilities, oil wells, brine-injection wells, pipelines, and pits are likely sources of brine in the study area. It is not possible to identify discrete oil-related features as likely sources of brine plumes because several features commonly are co-located. During the latter half of the twentieth century, many brine plumes migrated beyond the immediate source area and likely mix together in modern and ancestral Poplar River valley subareas.

Anti-dermatitis, anxiolytic and analgesic effects of Rhazya stricta from Balochistan.

PubMed

Ahmad, Mansoor; Muhammed, Shafi; Mehjabeen; Jahan, Noor; Jan, Syed Umer; Qureshi, Zia-Ul-Rehaman

2014-05-01

Current study was carried out on Rhazya stricta. Plant material was collected from Jhalmagsi Dist. Balochistan, Pakistan. Methanolic extract of Rhazya stricta was tested for anti-dermatitis, analgesic, anxiolytic effects, insecticidal activity and Brine shrimp Bioassay. Crude extract showed significant anti-dermatitis activity, as the results of intensity score showed mild Excoriation or erosion, moderate Edema or populations and absence of Erythema or hemorrhage, Scratching time was decreased to 1.45 and histological observations of mice treated with crude extract showed mild changes and few inflammatory cells in several microscopic fields. The results of analgesic activity were significant and the percentage inhibition of writhes were 73.54% and 69.38% at 300mg/kg and 500mg/kg respectively. The overall response of crude extract in anxiolytic activities were depressive and crude extract showed sedative effects. In Brine shrimp (Artemsia salina) lethality bioassay crude extract showed dose depended significant activity, and showed positive lethality with LD(50) 3.3004μg/ml. Insecticidal activity was positive against Callosbruchus analis, the percent mortality was 40%.

Modeling Episodic Ephemeral Brine Lake Evaporation and Salt Crystallization on the Bonneville Salt Flats, Utah

NASA Astrophysics Data System (ADS)

Liu, T.; Harman, C. J.; Kipnis, E. L.; Bowen, B. B.

2017-12-01

Public concern about apparent reductions in the areal extent of the Bonneville Salt Flat (BSF) and perceived changes in inundation frequency has motivated renewed interest in the hydrologic and geochemical behavior of this salt playa. In this study, we develop a numerical modeling framework to simulate the relationship between hydrometeorologic variability, brine evaporation and salt crystallization processes on BSF. The BSF, locates in Utah, is the remnant of paleo-lake Bonneville, and is capped by up to 1 meter of salt deposition over a 100 km2 area. The BSF has two distinct hydrologic periods each year: a winter wet periods with standing surface brine and the summer dry periods when the brine is evaporated, exposing the surface salt crust. We develop a lumped non-linear dynamical models coupling conservation expressions from water, dissolved salt and thermal energy to investigate the seasonal and diurnal behavior of brine during the transition from standing brine to exposed salt at BSF. The lumped dynamic models capture important nonlinear and kinetic effects introduced by the high ionic concentration of the brine, including the pronounced effect of the depressed water activity coefficient on evaporation. The salt crystallization and dissolution rate is modeled as a kinetic process linearly proportional to the degree of supersaturation of brine. The model generates predictions of the brine temperature and the solute and solvent masses controlled by diurnal net radiation input and aerodynamic forcing. Two distinct mechanisms emerge as potential controls on salt production and dissolution: (1) evapo-concentration and (2) changes in solubility related to changes in brine temperature. Although the evaporation of water is responsible for ultimate disappearance of the brine each season ,variation in solubility is found to be the dominant control on diurnal cycles of salt precipitation and dissolution in the BSF case. Most salt is crystallized during nighttime, but the long-term salt production is driven by the seasonal evapo-concentration. Moreover, we find that the timing of the brine temperature fluctuations and salt production lags the diurnal net radiation input. The key controls on the magnitudes of these effects and phase lags are determined by analytical periodic analysis of linearized forms of the model.

Experimental investigation of CO2-brine-rock interactions at elevated temperature and pressure: Implications for CO2 sequestration in deep-saline aquifers

USGS Publications Warehouse

Rosenbauer, R.J.; Koksalan, T.; Palandri, J.L.

2005-01-01

Deep-saline aquifers are potential repositories for excess CO2, currently being emitted to the atmosphere from anthropogenic activities, but the reactivity of supercritical CO2 with host aquifer fluids and formation minerals needs to be understood. Experiments reacting supercritical CO2 with natural and synthetic brines in the presence and absence of limestone and plagioclase-rich arkosic sandstone showed that the reaction of CO2-saturated brine with limestone results in compositional, mineralogical, and porosity changes in the aquifer fluid and rock that are dependent on initial brine composition, especially dissolved calcium and sulfate. Experiments reacting CO2-saturated, low-sulfate brine with limestone dissolved 10% of the original calcite and increased rock porosity by 2.6%. Experiments reacting high-sulfate brine with limestone, both in the presence and absence of supercritical CO2, were characterized by the precipitation of anhydrite, dolomitization of the limestone, and a final decrease in porosity of 4.5%. However, based on favorable initial porosity changes of about 15% due to the dissolution of calcite, the combination of CO2 co-injection with other mitigation strategies might help alleviate some of the well-bore scale and formation-plugging problems near the injection zone of a brine disposal well in Paradox Valley, Colorado, as well as provide a repository for CO2. Experiments showed that the solubility of CO2 is enhanced in brine in the presence of limestone by 9% at 25 ??C and 6% at 120 ??C and 200 bar relative to the brine itself. The solubility of CO2 is enhanced also in brine in the presence of arkosic sandstone by 5% at 120 ??C and 300 bar. The storage of CO 2 in limestone aquifers is limited to only ionic and hydraulic trapping. However, brine reacted with supercritical CO2 and arkose yielded fixation and sequestration of CO2 in carbonate mineral phases. Brine desiccation was observed in all experiments containing a discrete CO2 phase, promoting porosity-reducing precipitation reactions in aquifers near saturation with mineral phases. Published by Elsevier B.V.

Survival of Escherichia coli O157:H7 during manufacture and storage of white brined cheese.

PubMed

Osaili, Tareq M; Al-Nabulsi, Anas A; Olaimat, Amin N; Shaker, Reyad R; Taha, Mohammad; Holley, Richard A

2014-09-01

Escherichia coli O157:H7 is a major foodborne pathogen that causes severe disease in humans. Survival of E. coli O157:H7 during processing and storage of white brined cheese was investigated. Cheeses were prepared using pasteurized milk inoculated with a 4 strain E. coli O157:H7 cocktail (7 log(10) CFU/g) with or without yogurt starter culture (Lactobacillus delbrueckii ssp. bulgaricus and Streptococcus salivarius ssp. thermophilus) and stored in 10% or 15% NaCl brine at 10 and 21 ºC for 28 d. NaCl concentration, water activity (a(w)), pH, and numbers of E. coli O157:H7 and lactic acid bacteria (LAB) were determined in cheese and brine. E. coli O157:H7 was able to survive in cheese stored in both brines at 10 and 21 ºC regardless of the presence of starter LAB, although the latter significantly enhanced E. coli O157:H7 reduction in cheese or its brine at 10 ºC. E. coli O157:H7 numbers were reduced by 2.6 and 3.4 log(10) CFU/g in cheese stored in 10% and 15% NaCl brine, respectively, in the presence of starter LAB and by 1.4 and 2.3 log(10) CFU/g, respectively, in the absence of starter LAB at 10 ºC. The pathogen survived, but at lower numbers in the brines. The salt concentration of cheese stored in 10% brine remained about 5% during ripening, but in 15% brine, the NaCl level increased 1.6% to 8.1% (w/w) by 28 d. Values of pH and a(w) slightly decreased 1 d after exposure to brine and reached 5.5 to 6.6 and 0.88 to 0.94, respectively, in all treatments. © 2014 Institute of Food Technologists®

Deep well injection of brine from Paradox Valley, Colorado: Potential major precipitation problems remediated by nanofiltration

USGS Publications Warehouse

Kharaka, Yousif K.; Ambats, Gil; Thordsen, James J.; Davis, Roy A.

1997-01-01

Groundwater brine seepage into the Dolores River in Paradox Valley, Colorado, increases the dissolved solids load of the Colorado River annually by ∼2.0 × 108 kg. To abate this natural contamination, the Bureau of Reclamation plans to pump ∼3540 m3/d of brine from 12 shallow wells located along the Dolores River. The brine, with a salinity of 250,000 mg/L, will be piped to the deepest (4.9 km) disposal well in the world and injected mainly into the Mississippian Leadville Limestone. Geochemical modeling indicates, and water-rock experiments confirm, that a huge mass of anhydrite (∼1.0 × 104 kg/d) likely will precipitate from the injected brine at downhole conditions of 120°C and 500 bars. Anhydrite precipitation could increase by up to 3 times if the injected brine is allowed to mix with the highly incompatible formation water of the Leadville Limestone and if the Mg in this brine dolomitizes the calcite of the aquifer. Laboratory experiments demonstrate that nanofiltration membranes, which are selective to divalent anions, provide a new technology that remediates the precipitation problem by removing ∼98% of dissolved SO4 from the hypersaline brine. The fluid pressure used (50 bars) is much lower than would be required for traditional reverse osmosis membranes because nanofiltration membranes have a low rejection efficiency (5–10%) for monovalent anions. Our results indicate that the proportion of treatable brine increases from ∼60% to >85% with the addition of trace concentrations of a precipitation inhibitor and by blending the raw brine with the effluent stream.

Application of a Re-Pd bimetallic catalyst for treatment of perchlorate in waste ion-exchange regenerant brine.

PubMed

Liu, Jinyong; Choe, Jong Kwon; Sasnow, Zachary; Werth, Charles J; Strathmann, Timothy J

2013-01-01

Concentrated sodium chloride (NaCl) brines are often used to regenerate ion-exchange (IX) resins applied to treat drinking water sources contaminated with perchlorate (ClO(4)(-)), generating large volumes of contaminated waste brine. Chemical and biological processes for ClO(4)(-) reduction are often inhibited severely by high salt levels, making it difficult to recycle waste brines. Recent work demonstrated that novel rhenium-palladium bimetallic catalysts on activated carbon support (Re-Pd/C) can efficiently reduce ClO(4)(-) to chloride (Cl(-)) under acidic conditions, and here the applicability of the process for treating waste IX brines was examined. Experiments conducted in synthetic NaCl-only brine (6-12 wt%) showed higher Re-Pd/C catalyst activity than in comparable freshwater solutions, but the rate constant for ClO(4)(-) reduction measured in a real IX waste brine was found to be 65 times lower than in the synthetic NaCl brine. Through a series of experiments, co-contamination of the IX waste brine by excess NO(3)(-) (which the catalyst reduces principally to NH(4)(+)) was found to be the primary cause for deactivation of the Re-Pd/C catalyst, most likely by altering the immobilized Re component. Pre-treatment of NO(3)(-) using a different bimetallic catalyst (In-Pd/Al(2)O(3)) improved selectivity for N(2) over NH(4)(+) and enabled facile ClO(4)(-) reduction by the Re-Pd/C catalyst. Thus, sequential catalytic treatment may be a promising strategy for enabling reuse of waste IX brine containing NO(3)(-) and ClO(4)(-). Copyright © 2012 Elsevier Ltd. All rights reserved.

Rheological Properties of Silica Nanoparticles in Brine and Brine-Surfactant Systems

NASA Astrophysics Data System (ADS)

Pales, Ashley; Kinsey, Erin; Li, Chunyan; Mu, Linlin; Bai, Lingyun; Clifford, Heather; Darnault, Christophe

2016-04-01

Rheological Properties of Silica Nanoparticles in Brine and Brine-Surfactant Systems Ashley R. Pales, Erin Kinsey, Chunyan Li, Linlin Mu, Lingyun Bai, Heather Clifford, and Christophe J. G. Darnault Department of Environmental Engineering and Earth Sciences, Laboratory of Hydrogeoscience and Biological Engineering, L.G. Rich Environmental Laboratory, Clemson University, Clemson, SC, USA Nanofluids are suspensions of nanometer sized particles in any fluid base, where the nanoparticles effect the properties of the fluid base. Commonly, nanofluids are water based, however, other bases such as ethylene-glycol, glycerol, and propylene-glycol, have been researched to understand the rheological properties of the nanofluids. This work aims to understand the fundamental rheological properties of silica nanoparticles in brine based and brine-surfactant based nanofluids with temperature variations. This was done by using variable weight percent of silica nanoparticles from 0.001% to 0.1%. Five percent brine was used to create the brine based nanofluids; and 5% brine with 2CMC of Tween 20 nonionic surfactant (Sigma-Aldrich) was used to create the brine-surfactant nanofluid. Rheological behaviors, such as shear rate, shear stress, and viscosity, were compared between these nanofluids at 20C and at 60C across the varied nanoparticle wt%. The goal of this work is to provide a fundamental basis for future applied testing for enhanced oil recovery. It is hypothesized that the addition of surfactant will have a positive impact on nanofluid properties that will be useful for enhance oil recovery. Differences have been observed in preliminary data analysis of the rheological properties between these two nanofluids indicating that the surfactant is having the hypothesized effect.

Preliminary Feasibility Testing of the BRIC Brine Water Recovery Concept

NASA Technical Reports Server (NTRS)

Callahan, Michael R.; Pensinger, Stuart J.; Pickering, Karen D.

2012-01-01

The Brine Residual In-Containment (BRIC) concept is being developed as a new technology to recover water from spacecraft wastewater brines. Such capability is considered critical to closing the water loop and achieving a sustained human presence in space. The intention of the BRIC concept is to increase the robustness and efficiency of the dewatering process by performing drying inside the container used for the final disposal of the residual brine solid. Recent efforts in the development of BRIC have focused on preliminary feasibility testing using a laboratory- assembled pre-prototype unit. Observations of the drying behavior of actual brine solutions processed under BRIC-like conditions has been of particular interest. To date, experiments conducted with three types of analogue spacecraft wastewater brines have confirmed the basic premise behind the proposed application of in-place drying. Specifically, the dried residual mass from these solutions have tended to exhibit characteristics of adhesion and flow that are expected to continue to challenge process stream management designs typically used in spacecraft systems. Yet, these same characteristics may favor the development of capillary- and surface-tension-based approaches currently envisioned as part of an ultimate microgravity-compatible BRIC design. In addition, preliminary feasibility testing of the BRIC pre-prototype confirmed that high rates of water recovery, up to 98% of the available brine water, may be possible while still removing the majority of the brine contaminants from the influent brine stream. These and other early observations from testing are reported.

Production and characterization of a functional Iranian white brined cheese by replacement of dairy fat with vegetable oils.

PubMed

Achachlouei, B Fathi; Hesari, J; Damirchi, S Azadmard; Peighambardoust, Sh; Esmaiili, M; Alijani, S

2013-10-01

Full-fat cheese usually contains high amounts of saturated fatty acids and cholesterol, which may have negative health effects. In this study, full-fat white brined cheese, as a control sample, and experimental cheeses with olive and canola oils (T1, white brined cheese containing 50% canola oil, T2, white brined cheese containing 50% olive oil, T3, white brined cheese containing 100% canola oil and T4, white brined cheese containing 100% olive oil) were prepared from bovine milk. Physicochemical properties, lipolysis, proteolysis patterns and sensorial properties in the prepared samples were determined during 80 days of storage at 20-day intervals. Cheese incorporating vegetable oils showed lower amounts of saturated fatty acids and higher amounts of unsaturated fatty acids compared with the full-fat cheese (control) samples. Moisture, pH, lipolysis value, as assessed by the acid-degree value, and proteolysis values (pH 4.6 SN/TN% and NPN/TN%) significantly (p < 0.05) were increased in all samples, whereas total titrable acidity decreased during 40 days of ripening but then increased slightly. Sensory properties of white brined cheese incorporating with vegetable oils were different from those of full-fat cheese samples. White brined cheese containing olive and canola oils (100% fat substitution) received better sensory scores compared to other samples. The results showed that it is possible to replace dairy fat with olive and canola oils, which can lead to produce a new healthy and functional white brined cheese.

Purification of High Salinity Brine by Multi-Stage Ion Concentration Polarization Desalination

PubMed Central

Kim, Bumjoo; Kwak, Rhokyun; Kwon, Hyukjin J.; Pham, Van Sang; Kim, Minseok; Al-Anzi, Bader; Lim, Geunbae; Han, Jongyoon

2016-01-01

There is an increasing need for the desalination of high concentration brine (>TDS 35,000 ppm) efficiently and economically, either for the treatment of produced water from shale gas/oil development, or minimizing the environmental impact of brine from existing desalination plants. Yet, reverse osmosis (RO), which is the most widely used for desalination currently, is not practical for brine desalination. This paper demonstrates technical and economic feasibility of ICP (Ion Concentration Polarization) electrical desalination for the high saline water treatment, by adopting multi-stage operation with better energy efficiency. Optimized multi-staging configurations, dependent on the brine salinity values, can be designed based on experimental and numerical analysis. Such an optimization aims at achieving not just the energy efficiency but also (membrane) area efficiency, lowering the true cost of brine treatment. ICP electrical desalination is shown here to treat brine salinity up to 100,000 ppm of Total Dissolved Solids (TDS) with flexible salt rejection rate up to 70% which is promising in a various application treating brine waste. We also demonstrate that ICP desalination has advantage of removing both salts and diverse suspended solids simultaneously, and less susceptibility to membrane fouling/scaling, which is a significant challenge in the membrane processes. PMID:27545955

Purification of High Salinity Brine by Multi-Stage Ion Concentration Polarization Desalination

NASA Astrophysics Data System (ADS)

Kim, Bumjoo; Kwak, Rhokyun; Kwon, Hyukjin J.; Pham, Van Sang; Kim, Minseok; Al-Anzi, Bader; Lim, Geunbae; Han, Jongyoon

2016-08-01

There is an increasing need for the desalination of high concentration brine (>TDS 35,000 ppm) efficiently and economically, either for the treatment of produced water from shale gas/oil development, or minimizing the environmental impact of brine from existing desalination plants. Yet, reverse osmosis (RO), which is the most widely used for desalination currently, is not practical for brine desalination. This paper demonstrates technical and economic feasibility of ICP (Ion Concentration Polarization) electrical desalination for the high saline water treatment, by adopting multi-stage operation with better energy efficiency. Optimized multi-staging configurations, dependent on the brine salinity values, can be designed based on experimental and numerical analysis. Such an optimization aims at achieving not just the energy efficiency but also (membrane) area efficiency, lowering the true cost of brine treatment. ICP electrical desalination is shown here to treat brine salinity up to 100,000 ppm of Total Dissolved Solids (TDS) with flexible salt rejection rate up to 70% which is promising in a various application treating brine waste. We also demonstrate that ICP desalination has advantage of removing both salts and diverse suspended solids simultaneously, and less susceptibility to membrane fouling/scaling, which is a significant challenge in the membrane processes.

Selenium biotransformations in an engineered aquatic ecosystem for bioremediation of agricultural wastewater via brine shrimp production.

PubMed

Schmidt, Radomir; Tantoyotai, Prapakorn; Fakra, Sirine C; Marcus, Matthew A; Yang, Soo In; Pickering, Ingrid J; Bañuelos, Gary S; Hristova, Krassimira R; Freeman, John L

2013-05-21

An engineered aquatic ecosystem was specifically designed to bioremediate selenium (Se), occurring as oxidized inorganic selenate from hypersalinized agricultural drainage water while producing brine shrimp enriched in organic Se and omega-3 and omega-6 fatty acids for use in value added nutraceutical food supplements. Selenate was successfully bioremediated by microalgal metabolism into organic Se (seleno-amino acids) and partially removed via gaseous volatile Se formation. Furthermore, filter-feeding brine shrimp that accumulated this organic Se were removed by net harvest. Thriving in this engineered pond system, brine shrimp ( Artemia franciscana Kellogg) and brine fly (Ephydridae sp.) have major ecological relevance as important food sources for large populations of waterfowl, breeding, and migratory shore birds. This aquatic ecosystem was an ideal model for study because it mimics trophic interactions in a Se polluted wetland. Inorganic selenate in drainage water was metabolized differently in microalgae, bacteria, and diatoms where it was accumulated and reduced into various inorganic forms (selenite, selenide, or elemental Se) or partially incorporated into organic Se mainly as selenomethionine. Brine shrimp and brine fly larva then bioaccumulated Se from ingesting aquatic microorganisms and further metabolized Se predominately into organic Se forms. Importantly, adult brine flies, which hatched from aquatic larva, bioaccumulated the highest Se concentrations of all organisms tested.

Magnesium compounds

USGS Publications Warehouse

Kramer, D.A.

2012-01-01

Seawater and natural brines accounted for about 57 percent of magnesium compounds produced in the United States in 2011. Dead-burned magnesia was produced by Martin Marietta Magnesia Specialties LLC from well brines in Michigan. Caustic-calcined magnesia was recovered from seawater by Premier Magnesia LLC in Florida, from well brines in Michigan by Martin Marietta and from magnesite in Nevada by Premier Magnesia. Intrepid Potash Wendover LLC and Great Salt Lake Minerals Corp. recovered magnesium chloride brines from the Great Salt Lake in Utah. Magnesium hydroxide was produced from seawater by SPI Pharma Inc. in Delaware and Premier Magnesia in Florida, and by Martin Marietta from its brine operation in Michigan.

Concentrated Brine Treatment using New Energy in Coal Mine Evaporation Ponds

NASA Astrophysics Data System (ADS)

Li, Ting; Li, Jingfeng

2017-12-01

Recently, more and more coal mine water is being advanced treated and reused in China. The concentrated brine that results from advanced treatment methods can only be evaporated in an evaporation pond. Because of limited treatment capabilities and winter freezing, evaporation ponds often overflow, causing environment contamination. In this paper, based on analysis of brine water quality and economic-technical feasibility, we present a suitable treatment method for brine in evaporation ponds as electrodialysis using solar energy. In addition, we propose a new system to treat brine in coal mine evaporation ponds, which is powered by solar and wind. The operating efficiency of this treatment system proposed in this paper can meet the concentrated brine treatment demands in most coal mines in western mining areas of China and it places the photovoltaic power generation plates on the surface of the evaporation pond on a fixed floating island, which reduces any risk associated with land acquisition. This system can enhance brine treatment efficiency, requires a reduced evaporation pond area, increases the utilization of coal mine water, and minimizes the risk of environment contamination.

Experimental multi-phase H2O-CO2 brine interactions at elevated temperature and pressure: Implications for CO2 sequestration in deep-saline aquifers

USGS Publications Warehouse

Rosenbauer, R.; Koksalan, T.

2004-01-01

The burning of fossil fuel and other anthropogenic activities have caused a continuous and dramatic 30% increase of atmospheric CO2 over the past 150 yr. CO2 sequestration is increasingly being viewed as a tool for managing these anthropogenic CO2 emissions to the atmosphere. CO2-saturated brine-rock experiments were carried out to evaluate the effects of multiphase H2O-CO2 fluids on mineral equilibria and the potential for CO2 sequestration in mineral phases within deep-saline aquifers. Experimental results were generally consistent with theoretical thermodynamic calculations. The solubility of CO2 was enhanced in brines in the presence of both limestone and sandstone relative to brines alone. Reactions between CO2 saturated brines and arkosic sandstones were characterized by desiccation of the brine and changes in the chemical composition of the brine suggesting fixation of CO2 in mineral phases. These reactions were occurring on a measurable but kinetically slow time scale at 120??C.

Within-wafer CD variation induced by wafer shape

NASA Astrophysics Data System (ADS)

Huang, Chi-hao; Yang, Mars; Yang, Elvis; Yang, T. H.; Chen, K. C.

2016-03-01

In order to meet the increasing storage capacity demand and reduce bit cost of NAND flash memories, 3D stacked vertical flash cell array has been proposed. In constructing 3D NAND flash memories, the bit number per unit area is increased as increasing the number of stacked layers. However, the increased number of stacked layers has made the film stress control extremely important for maintaining good process quality. The residual film stress alters the wafer shape accordingly several process impacts have been readily observed across wafer, such as film deposition non-uniformity, etch rate non-uniformity, wafer chucking error on scanner, materials coating/baking defects, overlay degradation and critical dimension (CD) non-uniformity. The residual tensile and compressive stresses on wafers will result in concave and convex wafer shapes, respectively. This study investigates within-wafer CD uniformity (CDU) associated with wafer shape change induced by the 3D NAND flash memory processes. Within-wafer CDU was correlated with several critical parameters including different wafer bow heights of concave and convex wafer shapes, photo resists with different post exposure baking (PEB) temperature sensitivities, and DoseMapper compensation. The results indicated the trend of within-wafer CDU maintains flat for convex wafer shapes with bow height up to +230um and concave wafer shapes with bow height ranging from 0 ~ -70um, while the within-wafer CDU trends up from -70um to -246um wafer bow heights. To minimize the within-wafer CD distribution induced by wafer warpage, carefully tailoring the film stack and thermal budget in the process flow for maintaining the wafer shape at CDU friendly range is indispensable and using photo-resist materials with lower PEB temperature sensitivity is also suggested. In addition, DoseMapper compensation is also an alternative to greatly suppress the within-wafer CD non-uniformity but the photo-resist profile variation induced by across-wafer PEB temperature non-uniformity attributed to wafer warpage is uncorrectable, and the photo-resist profile variation is believed to affect across-wafer etch bias uniformity to some degree.

Scanning electron microscope observations of brine shrimp larvae from space shuttle experiments

NASA Technical Reports Server (NTRS)

DeBell, L.; Paulsen, A.; Spooner, B.

1992-01-01

Brine shrimp are encysted as gastrula stage embryos, and may remain dehydrated and encysted for years without compromising their viability. This aspect of brine shrimp biology is desirable for studying development of animals during space shuttle flight, as cysts placed aboard a spacecraft may be rehydrated at the convenience of an astronaut, guaranteeing that subsequent brine shrimp development occurs only on orbit and not on the pad during launch delays. Brine shrimp cysts placed in 5 ml syringes were rehydrated with salt water and hatched during a 9 day space shuttle mission. Subsequent larvae developed to the 8th larval stage in the sealed syringes. We studied the morphogenesis of the brine shrimp larvae and found the larvae from the space shuttle experiments similar in rate of growth and extent of development, to larvae grown in sealed syringes on the ground. Extensive differentiation and development of embryos and larvae can occur in a microgravity environment.

Thermal-gradient migration of brine inclusions in salt crystals

NASA Astrophysics Data System (ADS)

Yagnik, S. K.

1982-09-01

High level nuclear waste disposal in a geologic repository was proposed. Natural salt deposits which are considered contain a small volume fraction of water in the form of brine inclusions distributed throughout the salt. Radioactive decay heating of the nuclear wastes will impose a temperature gradient on the surrounding salt which mobilizes the brine inclusions. Inclusions filled completely with brine migrate up the temperature gradient and eventually accumulate brine near the buried waste forms. The brine may slowly corrode or degrade the waste forms which is undesirable. In this work, thermal gradient migration of both all liquid and gas liquid inclusions was experimentally studied in synthetic single crystals of NaCl and KCl using a hot stage attachment to an optical microscope which was capable of imposing temperature gradients and axial compressive loads on the crystals. The migration velocities of the inclusion shape and size are discussed.

The Influence of Seal Properties on Pressure Buildup and Leakage of Carbon Dioxide from Sequestration Reservoirs (Invited)

NASA Astrophysics Data System (ADS)

Benson, S. M.; Chabora, E.

2009-12-01

The transport properties of seals, namely permeability, relative permeability, and capillary pressure control both migration of carbon dioxide and brine through the seal. Only recently has the the importance of brine migration emerged as key issue in the environmental performance of carbon dioxide sequestration projects. In this study we use numerical simulation to show that brine migration through the seal can be either advantageous or deleterious to the environmental performance of a carbon dioxide sequestration project. Brine migration through the seal can lower the pressure buildup in the storage reservoir, thereby reducing the risk of leakage or geomechanical stresses on the seal. On the other hand, if the seal is penetrated by a permeable fault it can lead to focused flow up a fault, which could lead to brine migration into drinking water aquifers. We also show that as the carbon dioxide plume grows, brine flow undergoes a complex evolution from upward flow to downward flows driven by countercurrent migration of carbon dioxide and brine in the seal and capillary pressure gradients at the base of the seal. Finally, we discuss desirable attributes seals, taking into account both carbon dioxide and brine migration through the seal. In particular, identifying seals that provide an effective capillary barrier to block the flow of carbon dioxide while allowing some brine migration through the seal can help to control pressure buildup and allow more efficient utilization of a sequestration reservoir. This could be particularly important in those settings that may be limited by the maximum allowable pressure buildup.

Calcium extraction from brine water and seawater using oxalic acid

NASA Astrophysics Data System (ADS)

Natasha, Nadia Chrisayu; Lalasari, Latifa Hanum

2017-01-01

Calcium can be extracted not only from rocks but also from natural liquor such as seawater and brine water. In order to extract the calcium from seawater and brine water, oxalic acid was used in this research. Effect of variations of the volume of the oxalic acid at a constant concentration in seawater and brine water to produce calcium was investigated. The concentration of oxalic acid was 100 g/l and the variations of its volume were 2 ml, 4 ml, 6 ml, 8 ml, 10 ml, 20 ml, 30 ml, 40 ml, and 50 ml. The used seawater and brine water were firstly evaporated from 100 ml into 50 ml and then the oxalic acid was added into them with mixing to produce the calcium precipitates. The precipitates were analyzed by X-ray diffraction (XRD) and scanning electron microscope (SEM) and the filtrates were analyzed by inductively coupled plasma-optical emission spectrometry (ICP-OES). The SEM analysis showed that the precipitates from brine water were consisted of only calcium compound while from seawater sodium one was also found along with calcium compound. The XRD analysis showed that the calcium was present in the form of calcium oxalate for both seawater and brine water. The ICP-OES analysis of the filtrate from seawater precipitation showed that the its calcium content was decreased from 826.20 ppm to 0.04 ppm while from brine water, it decreased from 170.06 ppm to 1.96 ppm. These results showed that both seawater and brine water have the potential to be a raw material for calcium production.

Brine flow up a borehole caused by pressure perturbation from CO2 storage: Static and dynamic evaluations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Birkholzer, J.T.; Nicot, J.-P.; Oldenburg, C.M.

Industrial-scale storage of CO{sub 2} in saline sedimentary basins will cause zones of elevated pressure, larger than the CO{sub 2} plume itself. If permeable conduits (e.g., leaking wells) exist between the injection reservoir and overlying shallow aquifers, brine could be pushed upwards along these conduits and mix with groundwater resources. This paper discusses the potential for such brine leakage to occur in temperature- and salinity-stratified systems. Using static mass-balance calculations as well as dynamic well flow simulations, we evaluate the minimum reservoir pressure that would generate continuous migration of brine up a leaking wellbore into a freshwater aquifer. Since themore » brine invading the well is denser than the initial fluid in the wellbore, continuous flow only occurs if the pressure perturbation in the reservoir is large enough to overcome the increased fluid column weight after full invasion of brine into the well. If the threshold pressure is exceeded, brine flow rates are dependent on various hydraulic (and other) properties, in particular the effective permeability of the wellbore and the magnitude of pressure increase. If brine flow occurs outside of the well casing, e.g., in a permeable fracture zone between the well cement and the formation, the fluid/solute transfer between the migrating fluid and the surrounding rock units can strongly retard brine flow. At the same time, the threshold pressure for continuous flow to occur decreases compared to a case with no fluid/solute transfer.« less

[Evaluation of Organ Dose Estimation from Indices of CT Dose Using Dose Index Registry].

PubMed

Iriuchijima, Akiko; Fukushima, Yasuhiro; Ogura, Akio

Direct measurement of each patient organ dose from computed tomography (CT) is not possible. Most methods to estimate patient organ dose is using Monte Carlo simulation with dedicated software. However, dedicated software is too expensive for small scale hospitals. Not every hospital can estimate organ dose with dedicated software. The purpose of this study was to evaluate the simple method of organ dose estimation using some common indices of CT dose. The Monte Carlo simulation software Radimetrics (Bayer) was used for calculating organ dose and analysis relationship between indices of CT dose and organ dose. Multidetector CT scanners were compared with those from two manufactures (LightSpeed VCT, GE Healthcare; SOMATOM Definition Flash, Siemens Healthcare). Using stored patient data from Radimetrics, the relationships between indices of CT dose and organ dose were indicated as each formula for estimating organ dose. The accuracy of estimation method of organ dose was compared with the results of Monte Carlo simulation using the Bland-Altman plots. In the results, SSDE was the feasible index for estimation organ dose in almost organs because it reflected each patient size. The differences of organ dose between estimation and simulation were within 23%. In conclusion, our estimation method of organ dose using indices of CT dose is convenient for clinical with accuracy.

An electron-beam dose deposition experiment: TIGER 1-D simulation code versus thermoluminescent dosimetry

NASA Astrophysics Data System (ADS)

Murrill, Steven R.; Tipton, Charles W.; Self, Charles T.

1991-03-01

The dose absorbed in an integrated circuit (IC) die exposed to a pulse of low-energy electrons is a strong function of both electron energy and surrounding packaging materials. This report describes an experiment designed to measure how well the Integrated TIGER Series one-dimensional (1-D) electron transport simulation program predicts dose correction factors for a state-of-the-art IC package and package/printed circuit board (PCB) combination. These derived factors are compared with data obtained experimentally using thermoluminescent dosimeters (TLD's) and the FX-45 flash x-ray machine (operated in electron-beam (e-beam) mode). The results of this experiment show that the TIGER 1-D simulation code can be used to accurately predict FX-45 e-beam dose deposition correction factors for reasonably complex IC packaging configurations.

Distillation Brine Purification for Resource Recovery Applications

NASA Technical Reports Server (NTRS)

Wheeler, Raymond M.

2014-01-01

Wastewater processing systems for space generate residual brine that contains water and salts that could be recovered to life support consumables. The project assessed the use of ion-exchange resins to selectively remove salts from wastewater treatment brines. The resins were then regenerated for additional use. The intention would be to generate a Na/K and CI rich or purified brine that would then be processed into high value chemicals, such as acids, bases, and/or bleach.

Assessment of fluid distribution and flow properties in two phase fluid flow using X-ray CT technology

NASA Astrophysics Data System (ADS)

Jiang, Lanlan; Wu, Bohao; Li, Xingbo; Wang, Sijia; Wang, Dayong; Zhou, Xinhuan; Zhang, Yi

2018-04-01

To study on microscale distribution of CO2 and brine during two-phase flow is crucial for understanding the trapping mechanisms of CO2 storage. In this study, CO2-brine flow experiments in porous media were conducted using X-ray computed tomography. The porous media were packed with glass beads. The pore structure (porosity/tortuosity) and flow properties at different flow rates and flow fractions were investigated. The results showed that porosity of the packed beads differed at different position as a result of heterogeneity. The CO2 saturation is higher at low injection flow rates and high CO2 fractions. CO2 distribution at the pore scale was also visualized. ∅ Porosity of porous media CT brine_ sat grey value of sample saturated with brine CT dry grey value of sample saturated with air CT brine grey value of pure brine CT air grey value of pure air CT flow grey values of sample with two fluids occupying the pore space {CT}_{CO_2_ sat} grey value of sample saturated with CO2 {f}_{CO_2}({S}_{CO_2}) CO2 fraction {q}_{CO_2} the volume flow rate for CO2 q brine the volume flow rate for brine L Thickness of the porous media, mm L e a bundle of capillaries of equal length, mm τ Tortuosity, calculated from L e / L.

Correlation Between Analytical and Thermodynamicaly Calculated Values of Density For Chloride-sodium Brines

NASA Astrophysics Data System (ADS)

Dudukalov, A.

Leakage from pipe-lines, nonhermetic wells and other industrial equipment of highly mineralized chloride-sodium brines, incidentally produced during oil field exploitation is one of the main source of fresh groundwater contamination on the Arlan oil field. Thermodynamic calculation, aimed to define more exactly brines chemical composi- tion and density was carried out by FREZCHEM2 program (Mironenko M.V. et al. 1997). Five brines types with mineralization of 137.9, 181.2, 217.4, 243.7, 267.8 g/l and density of 1.176, 1.09, 1.135, 1.153, 1.167 g/cm3 correspondingly were used. It is necessary to note that preliminarily chemical compositions of two last brines were corrected according to their mineralization. During calculations it was determined the following density values of brines: 1.082, 1.114, 1.131, 1.146, 1.158 g/cm3 conse- quently. Obtained results demonstrate the significant discrepancy in experimental and model estimates. Significant excess of anions over cations in experimental data indicates a major prob- lem with the analytical measurements. During calculations it was analyzed the possi- bility of changes in brines density depending on editing to cations or deducting from anions requisite amount of agent for keeping charge balance equal to zero. Received results demonstrate that in this case brines density can change on 0.004-0.011 g/cm3.

Origin of CaCl2 brines by basalt-seawater interaction: Insights provided by some simple mass balance calculations

NASA Astrophysics Data System (ADS)

Hardie, Lawrence A.

1983-06-01

Modern rift zone hydrothermal brines are typically CaCl2-bearing brines, an unusual chemical signature they share with certain oil field brines, fluid inclusions in ore minerals and a few uncommon saline lakes. Many origins have been suggested for such CaCl2 brines but in the Reykjanes, Iceland, geothermal system a strong empirical case can be made for a basalt-seawater interaction origin. To examine this mechanism of CaCl2 brine evolution some simple mass balance calculations were carried out. Average Reykjanes olivine tholeiite was “reacted” with average North Atlantic seawater to make an albite-chlorite-epidotesphene rock using Al2O3 as the conservative rock component and Cl as the conservative fluid component. The excess components released by the basalt to the fluid were “precipitated” at 275° C as quartz, calcite, anhydrite, magnetite and pyrite to complete the conversion to greenstone. The resulting fluid was a CaCl2 brine of seawater chlorinity with a composition remarkably similar to the actual Reykjanes brine at 1750 m depth. Thus, the calculations strongly support the idea that the Reykjanes CaCl2 brines result from “closed system” oceanic basalt-seawater interaction (albitization — chloritization mechanism) at greenschist facies temperatures. The calculation gives a seawater: basalt mass ratio of 3∶1 to 4∶1 (vol. ratio of 9∶1 to 12∶1), in keeping with experimental results, submarine vent data and with ocean crust cooling calculations. The brine becomes anoxic because there is insufficient dissolved or combined oxygen to balance all the Fe released from the basalt during alteration. Large excesses of Ca are released to the fluid and precipitate out in the form of anhydrite which essentially sweeps the brine free of sulfate leaving an elevated Ca concentration. The calculated rock-water interaction basically involves Na + Mg + SO4 ⇌ Ca + K, simulating chemical differences observed between oceanic basalts and greenstones from many mid-ocean ridges.

Guidelines to Facilitate the Evaluation of Brines for Winter Roadway Maintenance Operations.

DOT National Transportation Integrated Search

2017-09-19

This document presents guidelines to facilitate the evaluation of brines for winter weather roadway maintenance applications in Texas. Brines are used in anti-icing applications which typically consist of placing liquid snow and ice control chemicals...

6. VIEW OF BRINING TANK Older, redwood model. Paddles agitated ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

6. VIEW OF BRINING TANK Older, redwood model. Paddles agitated the skins while they soaked in brine. The skins were then hung to dry. - Sealing Plant, St. George Island, Pribilof Islands, Saint George, Aleutians West Census Area, AK

Weeks Island brine diffuser site study: baseline conditions and environmental assessment technical report

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

1980-12-12

This technical report presents the results of a study conducted at two alternative brine diffuser sites (A and B) proposed for the Weeks Island salt dome, together with an analysis of the potential physical, chemical, and biological effects of brine disposal for this area of the Gulf of Mexico. Brine would result from either the leaching of salt domes to form or enlarge oil storage caverns, or the subsequent use of these caverns for crude oil storage in the Strategic Petroleum Reserve (SPR) program. Brine leached from the Weeks Island salt dome would be transported through a pipeline which wouldmore » extend from the salt dome either 27 nautical miles (32 statute miles) for Site A, or 41 nautical miles (47 statute miles) for Site B, into Gulf waters. The brine would be discharged at these sites through an offshore diffuser at a sustained peak rate of 39 ft/sup 3//sec. The disposal of large quantities of brine in the Gulf could have a significant impact on the biology and water quality of the area. Physical and chemical measurements of the marine environment at Sites A and B were taken between September 1977 and July 1978 to correlate the existing environmental conditions with the estimated physical extent of tthe brine discharge as predicted by the MIT model (US Dept. of Commerce, 1977a). Measurements of wind, tide, waves, currents, and stratification (water column structure) were also obtained since the diffusion and dispersion of the brine plume are a function of the local circulation regime. These data were used to calculate both near- and far-field concentrations of brine, and may also be used in the design criteria for diffuser port configuration and verification of the plume model. Biological samples were taken to characterize the sites and to predict potential areas of impact with regard to the discharge. This sampling focused on benthic organisms and demersal fish. (DMC)« less

Assessment of two-phase flow on the chemical alteration and sealing of leakage pathways in cemented wellbores

DOE PAGES

Iyer, Jaisree; Walsh, Stuart D. C.; Hao, Yue; ...

2018-01-08

Wellbore leakage tops the list of perceived risks to the long-term geologic storage of CO 2, because wells provide a direct path between the CO 2 storage reservoir and the atmosphere. In this paper, we have coupled a two-phase flow model with our original framework that combined models for reactive transport of carbonated brine, geochemistry of reacting cement, and geomechanics to predict the permeability evolution of cement fractures. Additionally, this makes the framework suitable for field conditions in geological storage sites, permitting simulation of contact between cement and mixtures of brine and supercritical CO 2. Due to lack of conclusivemore » experimental data, we tried both linear and Corey relative permeability models to simulate flow of the two phases in cement fractures. The model also includes two options to account for the inconsistent experimental observations regarding cement reactivity with two-phase CO 2-brine mixtures. One option assumes that the reactive surface area is independent of the brine saturation and the second option assumes that the reactive surface area is proportional to the brine saturation. We have applied the model to predict the extent of cement alteration, the conditions under which fractures seal, the time it takes to seal a fracture, and the leakage rates of CO 2 and brine when damage zones in the wellbore are exposed to two-phase CO 2-brine mixtures. Initial brine residence time and the initial fracture aperture are critical parameters that affect the fracture sealing behavior. We also evaluated the importance of the model assumptions regarding relative permeability and cement reactivity. These results illustrate the need to understand how mixtures of carbon dioxide and brine flow through fractures and react with cement to make reasonable predictions regarding well integrity. For example, a reduction in the cement reactivity with two-phase CO 2-brine mixture can not only significantly increase the sealing time for fractures but may also prevent fracture sealing.« less

Assessment of two-phase flow on the chemical alteration and sealing of leakage pathways in cemented wellbores

DOE Office of Scientific and Technical Information (OSTI.GOV)

Iyer, Jaisree; Walsh, Stuart D. C.; Hao, Yue

Wellbore leakage tops the list of perceived risks to the long-term geologic storage of CO 2, because wells provide a direct path between the CO 2 storage reservoir and the atmosphere. In this paper, we have coupled a two-phase flow model with our original framework that combined models for reactive transport of carbonated brine, geochemistry of reacting cement, and geomechanics to predict the permeability evolution of cement fractures. Additionally, this makes the framework suitable for field conditions in geological storage sites, permitting simulation of contact between cement and mixtures of brine and supercritical CO 2. Due to lack of conclusivemore » experimental data, we tried both linear and Corey relative permeability models to simulate flow of the two phases in cement fractures. The model also includes two options to account for the inconsistent experimental observations regarding cement reactivity with two-phase CO 2-brine mixtures. One option assumes that the reactive surface area is independent of the brine saturation and the second option assumes that the reactive surface area is proportional to the brine saturation. We have applied the model to predict the extent of cement alteration, the conditions under which fractures seal, the time it takes to seal a fracture, and the leakage rates of CO 2 and brine when damage zones in the wellbore are exposed to two-phase CO 2-brine mixtures. Initial brine residence time and the initial fracture aperture are critical parameters that affect the fracture sealing behavior. We also evaluated the importance of the model assumptions regarding relative permeability and cement reactivity. These results illustrate the need to understand how mixtures of carbon dioxide and brine flow through fractures and react with cement to make reasonable predictions regarding well integrity. For example, a reduction in the cement reactivity with two-phase CO 2-brine mixture can not only significantly increase the sealing time for fractures but may also prevent fracture sealing.« less

Numerical analysis of seawater circulation in carbonate platforms: II. The dynamic interaction between geothermal and brine reflux circulation

USGS Publications Warehouse

Jones, G.D.; Whitaker, F.F.; Smart, P.L.; Sanford, W.E.

2004-01-01

Density-driven seawater circulation may occur in carbonate platforms due to geothermal heating and / or reflux of water of elevated salinity. In geothermal circulation lateral contrasts in temperature between seawater and platform groundwaters warmed by the geothermal heat flux result in upward convective flow, with colder seawater drawn into the platform at depth. With reflux circulation, platform-top waters concentrated by evaporation flow downward, displacing less dense underlying groundwaters. We have used a variable density groundwater flow model to examine the pattern, magnitude and interaction of these two different circulation mechanisms, for mesosaline platform-top waters (50???) and brines concentrated up to saturation with respect to gypsum (150???) and halite (246???). Geothermal circulation, most active around the platform margin, becomes restricted and eventually shut-off by reflux of brines from the platform interior towards the margin. The persistence of geothermal circulation is dependent on the rate of brine reflux, which is proportional to the concentration of platform-top brines and also critically dependent on the magnitude and distribution of permeability. Low permeability evaporites can severely restrict reflux whereas high permeability units in hydraulic continuity enhance brine transport. Reduction in permeability with depth and anisotropy of permeability (kv < < kh) focuses flow laterally in the shallow subsurface (<1 km), resulting in a horizontally elongated brine plume. Aquifer porosity and dispersivity are relatively minor controls on reflux. Platform brines can entrain surficial seawater when brine generating conditions cease but the platform-top remains submerged, a variant of reflux we term "latent reflux". Brines concentrated up to gypsum saturation have relatively long residence times of at least 100 times the duration of the reflux event. They thus represent a long-term control on post-reflux groundwater circulation, and consequently on the rates and spatial patterns of shallow burial diagenesis, such as dolomitization.

Strontium isotope systematics of mixing groundwater and oil-field brine at Goose Lake in northeastern Montana, USA

USGS Publications Warehouse

Peterman, Zell E.; Thamke, Joanna N.; Futa, Kiyoto; Preston, Todd

2012-01-01

Groundwater, surface water, and soil in the Goose Lake oil field in northeastern Montana have been affected by Cl−-rich oil-field brines during long-term petroleum production. Ongoing multidisciplinary geochemical and geophysical studies have identified the degree and local extent of interaction between brine and groundwater. Fourteen samples representing groundwater, surface water, and brine were collected for Sr isotope analyses to evaluate the usefulness of 87Sr/86Sr in detecting small amounts of brine. Differences in Sr concentrations and 87Sr/86Sr are optimal at this site for the experiment. Strontium concentrations range from 0.13 to 36.9 mg/L, and corresponding 87Sr/86Sr values range from 0.71097 to 0.70828. The local brine has 168 mg/L Sr and a 87Sr/86Sr value of 0.70802. Mixing relationships are evident in the data set and illustrate the sensitivity of Sr in detecting small amounts of brine in groundwater. The location of data points on a Sr isotope-concentration plot is readily explained by an evaporation-mixing model. The model is supported by the variation in concentrations of most of the other solutes.

Recovery of energy from geothermal brine and other hot water sources

DOEpatents

Wahl, III, Edward F.; Boucher, Frederic B.

1981-01-01

Process and system for recovery of energy from geothermal brines and other hot water sources, by direct contact heat exchange between the brine or hot water, and an immiscible working fluid, e.g. a hydrocarbon such as isobutane, in a heat exchange column, the brine or hot water therein flowing countercurrent to the flow of the working fluid. The column can be operated at subcritical, critical or above the critical pressure of the working fluid. Preferably, the column is provided with a plurality of sieve plates, and the heat exchange process and column, e.g. with respect to the design of such plates, number of plates employed, spacing between plates, area thereof, column diameter, and the like, are designed to achieve maximum throughput of brine or hot water and reduction in temperature differential at the respective stages or plates between the brine or hot water and the working fluid, and so minimize lost work and maximize efficiency, and minimize scale deposition from hot water containing fluid including salts, such as brine. Maximum throughput approximates minimum cost of electricity which can be produced by conversion of the recovered thermal energy to electrical energy.

Ulipristal acetate versus leuprolide acetate for uterine fibroids.

PubMed

Donnez, Jacques; Tomaszewski, Janusz; Vázquez, Francisco; Bouchard, Philippe; Lemieszczuk, Boguslav; Baró, Francesco; Nouri, Kazem; Selvaggi, Luigi; Sodowski, Krzysztof; Bestel, Elke; Terrill, Paul; Osterloh, Ian; Loumaye, Ernest

2012-02-02

The efficacy and side-effect profile of ulipristal acetate as compared with those of leuprolide acetate for the treatment of symptomatic uterine fibroids before surgery are unclear. In this double-blind noninferiority trial, we randomly assigned 307 patients with symptomatic fibroids and excessive uterine bleeding to receive 3 months of daily therapy with oral ulipristal acetate (at a dose of either 5 mg or 10 mg) or once-monthly intramuscular injections of leuprolide acetate (at a dose of 3.75 mg). The primary outcome was the proportion of patients with controlled bleeding at week 13, with a prespecified noninferiority margin of -20%. Uterine bleeding was controlled in 90% of patients receiving 5 mg of ulipristal acetate, in 98% of those receiving 10 mg of ulipristal acetate, and in 89% of those receiving leuprolide acetate, for differences (as compared with leuprolide acetate) of 1.2 percentage points (95% confidence interval [CI], -9.3 to 11.8) for 5 mg of ulipristal acetate and 8.8 percentage points (95% CI, 0.4 to 18.3) for 10 mg of ulipristal acetate. Median times to amenorrhea were 7 days for patients receiving 5 mg of ulipristal acetate, 5 days for those receiving 10 mg of ulipristal acetate, and 21 days for those receiving leuprolide acetate. Moderate-to-severe hot flashes were reported for 11% of patients receiving 5 mg of ulipristal acetate, for 10% of those receiving 10 mg of ulipristal acetate, and for 40% of those receiving leuprolide acetate (P<0.001 for each dose of ulipristal acetate vs. leuprolide acetate). Both the 5-mg and 10-mg daily doses of ulipristal acetate were noninferior to once-monthly leuprolide acetate in controlling uterine bleeding and were significantly less likely to cause hot flashes. (Funded by PregLem; ClinicalTrials.gov number, NCT00740831.).

Results of the GCMS Effluent Gas Analysis for the Brine Processing Test

NASA Technical Reports Server (NTRS)

Delzeit, Lance; Lee, Jeffrey; Flynn, Michael; Fisher, John; Shaw, Hali; Kawashima, Brian; Beeler, David; Harris, Linden

2015-01-01

The effluent gas for the Paragon Ionomer Water Processor (IWP), UMPQUA Ultrasonic Brine Dewatering System (UBDS), and the NASA Brine Evaporation Bag (BEB) were analyzed using Headspace GCMS Analysis in the recent AES FY14 Brine Processing Test. The results from the analysis describe the number and general chemical species of the chemicals produced. Comparisons were also made between the different chromatograms for each system, and an explanation of the differences in the results is reported.

West Hackberry Strategic Petroleum Reserve site brine-disposal monitoring, Year I report. Volume III. Biological oceanography. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

DeRouen, L.R.; Hann, R.W.; Casserly, D.M.

1983-02-01

The Department of Energy's Strategic Petroleum Reserve Program began discharging brine into the Gulf of Mexico from its West Hackberry site near Cameron, Louisiana in May 1981. The brine originates from underground salt domes being leached with water from the Intracoastal Waterway, making available vast underground storage caverns for crude oil. The effects of brine discharge on aquatic organisms are presented in this volume. The topics covered are: benthos; nekton; phytoplankton; zooplankton; and data management.

Microbial community profiles and microbial carbon cycling in Orca Basin

NASA Astrophysics Data System (ADS)

Hyde, A.; Teske, A.; Joye, S. B.; Montoya, J. P.; Nigro, L.

2016-12-01

Orca Basin is the largest seafloor brine pools in the world, covering over 400 km2 and reaching brine layer depths of 200 m. The brine pool contains water 8 times denser than the overlying seawater and is separated from the overlying water column by a sharp pycnocline that prevents vertical mixing. The transition from ambient seawater to brine occurs over 100 m [2150 to 2250 m] and is characterized by distinct changes in temperature, salinity, chemical conditions, oxygen, and organic matter concentration. The sharp brine-seawater interface results in a sharp pycnocline, which serves as a particle trap for sinking marine organic matter. Previous studies have used lipids to show that this organic-rich interface is host to an active microbial community which is potentially involved in deep-sea carbon remineralization and metal-cycling. Additionally, previous work on methane, ethane, and propane concentrations and 13C-isotopic signatures has also implicated the brine pool, as well as the interface, as sources for biogenic low-molecular weight hydrocarbons, resulting from the high concentration of suspended organic matter above and within the brine pool. Here we investigate the profiles of microbial community composition and metabolic potential in Orca Basin, ranging from seawater through the Orca Basin chemocline and into the deep Orca Basin brine. To characterize the microbial community and stratification, we used high-throughput bacterial and archaeal 16S rRNA gene sequencing of filtered water above, within, and below the Orca Basin chemocline. Our sequence data shows that three distinct and unique communities exist in the Orca Basin water column. We also use thermodynamic modeling of hydrocarbon degradation to investigate the favorability of C1-C3 hydrocarbon oxidation at the brine-seawater interface and the potential for Orca Basin to serve as a deep-sea hydrocarbon sink.

Inland Treatment of the Brine Generated from Reverse Osmosis Advanced Membrane Wastewater Treatment Plant Using Epuvalisation System

PubMed Central

Qurie, Mohannad; Abbadi, Jehad; Scrano, Laura; Mecca, Gennaro; Bufo, Sabino A.; Khamis, Mustafa; Karaman, Rafik

2013-01-01

The reverse osmosis (RO) brine generated from the Al-Quds University wastewater treatment plant was treated using an epuvalisation system. The advanced integrated wastewater treatment plant included an activated sludge unit, two consecutive ultrafiltration (UF) membrane filters (20 kD and 100 kD cutoffs) followed by an activated carbon filter and a reverse osmosis membrane. The epuvalisation system consisted of salt tolerant plants grown in hydroponic channels under continuous water flowing in a closed loop system, and placed in a greenhouse at Al-Quds University. Sweet basil (Ocimum basilicum) plants were selected, and underwent two consecutive hydroponic flowing stages using different brine-concentrations: an adaptation stage, in which a 1:1 mixture of brine and fresh water was used; followed by a functioning stage, with 100% brine. A control treatment using fresh water was included as well. The experiment started in April and ended in June (2012). At the end of the experiment, analysis of the effluent brine showed a remarkable decrease of electroconductivity (EC), PO43−, chemical oxygen demand (COD) and K+ with a reduction of 60%, 74%, 70%, and 60%, respectively, as compared to the influent. The effluent of the control treatment showed 50%, 63%, 46%, and 90% reduction for the same parameters as compared to the influent. Plant growth parameters (plant height, fresh and dry weight) showed no significant difference between fresh water and brine treatments. Obtained results suggest that the epuvalisation system is a promising technique for inland brine treatment with added benefits. The increasing of channel number or closed loop time is estimated for enhancing the treatment process and increasing the nutrient uptake. Nevertheless, the epuvalisation technique is considered to be simple, efficient and low cost for inland RO brine treatment. PMID:23823802

Effects of brine contamination from energy development on wetland macroinvertebrate community structure in the Prairie Pothole Region

USGS Publications Warehouse

Preston, Todd M.; Borgreen, Michael J.; Ray, Andrew M.

2018-01-01

Wetlands in the Prairie Pothole Region (PPR) of North America support macroinvertebrate communities that are integral to local food webs and important to breeding waterfowl. Macroinvertebrates in PPR wetlands are primarily generalists and well adapted to within and among year changes in water permanence and salinity. The Williston Basin, a major source of U.S. energy production, underlies the southwest portion of the PPR. Development of oil and gas results in the coproduction of large volumes of highly saline, sodium chloride dominated water (brine) and the introduction of brine can alter wetland salinity. To assess potential effects of brine contamination on macroinvertebrate communities, 155 PPR wetlands spanning a range of hydroperiods and salinities were sampled between 2014 and 2016. Brine contamination was documented in 34 wetlands with contaminated wetlands having significantly higher chloride concentrations, specific conductance and percent dominant taxa, and significantly lower taxonomic richness, Shannon diversity, and Pielou evenness scores compared to uncontaminated wetlands. Non-metric multidimensional scaling found significant correlations between several water quality parameters and macroinvertebrate communities. Chloride concentration and specific conductance, which can be elevated in naturally saline wetlands, but are also associated with brine contamination, had the strongest correlations. Five wetland groups were identified from cluster analysis with many of the highly contaminated wetlands located in a single cluster. Low or moderately contaminated wetlands were distributed among the remaining clusters and had macroinvertebrate communities similar to uncontaminated wetlands. While aggregate changes in macroinvertebrate community structure were observed with brine contamination, systematic changes were not evident, likely due to the strong and potentially confounding influence of hydroperiod and natural salinity. Therefore, despite the observed negative response of macroinvertebrate communities to brine contamination, macroinvertebrate community structure alone is likely not the most sensitive indicator of brine contamination in PPR wetlands.

Mechanisms of sulfate removal from subsurface calcium chloride brines: Heletz-Kokhav oilfields, Israel

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gavrieli, I.; Starinsky, A.; Spiro, B.

1995-09-01

The evolution of the Ca-chloride brines in the Heletz Formation, Lower Cretaceous, in the southern coastal plain of Israel was reconstructed through the study of its sulfate concentration and isotopic composition. Particular emphasis was given to the brine-oil interaction in the oilfields and to the sulfate depletion and lower SO{sub 4}/Cl ratio in brines in contact with hydrocarbons (oil brines) relative to {open_quotes}oil-free{close_quotes} from dry wells in the same oilfields. A method is presented for a calculation of the amount of sulfate removed from the original seawater in the various stages of its evolution to Ca-chloride brine. Eastward migration ofmore » the Messinian Ca-Chloride brine into the Heletz Formation was accompanied by dolomitization of the country rock. Final depletion of sulfate from the brines took place, and possibly still occurs, in the presence of crude oil in the oilfields. The two oil-producing fields, Heletz and Kokhav, occupy different areas on a Rayleigh distillation diagram. Sulfate depletion in both fields is accompanied by an increase in {delta}{sup 34}S{sub SO}{sub 4}, which reaches a maximum values of 59{per_thousand}. The above correlation is explained by bacterial sulfate reduction facilitated by the contact with the crude. Samples collected from the same boreholes at time intervals of several months show two opposing trends: sulfate concentration decrease accompanied by increase in {delta}{sup 34}S{sub SO}{sub 4}, and vice versa. While the first can be explained as in situ bacterial sulfate reduction, the latter attest to subsurface brine migration, as would be expected in oil-producing fields.« less

Seismic Signatures of Brine Release at Blood Falls, Taylor Glacier, Antarctica

NASA Astrophysics Data System (ADS)

Carr, C. G.; Pettit, E. C.; Carmichael, J.

2017-12-01

Blood Falls is created by the release of subglacially-sourced, iron-rich brine at the surface of Taylor Glacier, McMurdo Dry Valleys, Antarctica. The supraglacial portion of this hydrological feature is episodically active. Englacial liquid brine flow occurs despite ice temperatures of -17°C and we document supraglacial liquid brine release despite ambient air temperatures average -20°C. In this study, we use data from a seismic network, time-lapse cameras, and publicly available weather station data to address the questions: what are the characteristics of seismic events that occur during Blood Falls brine release and how do these compare with seismic events that occur during times of Blood Falls quiescence? How are different processes observable in the time-lapse imagery represented in the seismic record? Time-lapse photography constrains the timing of brine release events during the austral winter of 2014. We use a noise-adaptive digital power detector to identify seismic events and cluster analysis to identify repeating events based on waveform similarity across the network. During the 2014 wintertime brine release, high-energy repeated seismic events occurred proximal to Blood Falls. We investigate the ground motions associated with these clustered events, as well as their spatial distribution. We see evidence of possible tremor during the brine release periods, an indicator of fluid movement. If distinctive seismic signatures are associated with Blood Falls brine release they could be identified based solely on seismic data without any aid from time-lapse cameras. Passive seismologic monitoring has the benefit of continuity during the polar night and other poor visibility conditions, which make time-lapse imagery unusable.

NASA TechPort Entry for Coiled Brine Recovery Assembly (CoBRA) CL IR&D Project

NASA Technical Reports Server (NTRS)

Pensinger, Stuart

2014-01-01

The Coiled Brine Recovery Assembly (CoBRA) project will result in a proof-of-concept demonstration for a lightweight, compact, affordable, regenerable and disposable solution to brine water recovery. The heart of CoBRA is an evaporator that produces water vapor from brine. This evaporator leverages a novel design that enables passive transport of brine from place to place within the system. While it will be necessary to build or modify a system for testing the CoBRA concept, the emphasis of this project will be on developing the evaporator itself. This project will utilize a “test early, test often” approach, building at least one trial evaporator to guide the design of the final product.

Alcohol Brine Freezing of Japanese Horse Mackerel (Trachurus japonicus) for Raw Consumption

NASA Astrophysics Data System (ADS)

Maeda, Toshimichi; Yuki, Atsuhiko; Sakurai, Hiroshi; Watanabe, Koichiro; Itoh, Nobuo; Inui, Etsuro; Seike, Kazunori; Mizukami, Yoichi; Fukuda, Yutaka; Harada, Kazuki

In order to test the possible application of alcohol brine freezing to Japanese horse mackerel (Trachurus japonicus) for raw consumption, the quality and taste of fish frozen by direct immersion in 60% ethanol brine at -20, -25 and -30°C was compared with those by air freezing and fresh fish without freezing. Cracks were not found during the freezing. Smell of ethanol did not remain. K value, an indicator of freshness, of fish frozen in alcohol brine was less than 8.3%, which was at the same level as those by air freezing and fresh fish. Oxidation of lipid was at the same level as air freezing does, and lower than that of fresh fish. The pH of fish frozen in alcohol brine at -25 and -30°C was 6.5 and 6.6, respectively, which were higher than that by air freezing and that of fresh fish. Fish frozen in alcohol brine was better than that by air and at the same level as fresh fish in total evaluation of sensory tests. These results show that the alcohol brine freezing is superior to air freezing, and fish frozen in alcohol brine can be a material for raw consumption. The methods of thawing in tap water, cold water, refrigerator, and at room temperature were compared. Thawing in tap water is considered to be convenient due to the short thaw time and the quality of thawed fish that was best among the methods.

Quality of cucumbers commercially fermented in calcium chloride brine without sodium salts

USDA-ARS?s Scientific Manuscript database

Commercial cucumber fermentation produces large volumes of salty wastewater. This study evaluated the quality of fermented cucumbers produced commercially using an alternative calcium chloride brining process. Fermentation conducted in calcium brines (0.1M calcium chloride, 6mM potassium sorbate, eq...

Potential for Natural Brine for Anti-Icing and De-Icing

DOT National Transportation Integrated Search

2012-09-01

This project focused on the feasibility of the use of natural brine for anti-icing and pre-wetting in Onondaga County, : Syracuse, New York. A thorough literature review was conducted on the use of brine as an anti-icing and pre-wetting : agent both ...

Fermentation of cucumbers brined with calcium chloride instead of sodium chloride

USDA-ARS?s Scientific Manuscript database

Generation of waste water containing sodium chloride from cucumber fermentation tank yards could be eliminated if cucumbers were fermented in brines that did not contain this salt. To determine if this is feasible, cucumbers were fermented in brines that contained only calcium chloride to maintain f...

Norm removal from frac water

DOEpatents

Silva, James Manio; Matis, Hope; Kostedt, IV, William Leonard

2014-11-18

A method for treating low barium frac water includes contacting a frac water stream with a radium selective complexing resin to produce a low radium stream, passing the low radium stream through a thermal brine concentrator to produce a concentrated brine; and passing the concentrated brine through a thermal crystallizer to yield road salt.

Fermentation cover brine reformulation for cucumber processing with low salt to reduce bloater defect

USDA-ARS?s Scientific Manuscript database

Reformulation of calcium chloride cover brine for cucumber fermentation was explored as a mean to minimize the incidence of bloater defect. This study particularly focused on cover brine supplementation with calcium hydroxide, sodium chloride (NaCl), and acids to enhance buffer capacity, inhibit the...

Potential for natural brine for anti-icing and de-icing.

DOT National Transportation Integrated Search

2012-09-01

This project focused on the feasibility of the use of natural brine for anti-icing and pre-wetting in Onondaga County, Syracuse, New York. A thorough literature review was conducted on the use of brine as an anti-icing and pre-wetting agent both in t...

REE Sorption Study on sieved -50 +100 mesh fraction of Media #1 in Brine #1 with Different Starting pH's at 70C

DOE Data Explorer

Gary Garland

2015-09-29

This is a continuation of the REE sorption study for shaker bath tests on 2g media #1 in 150mL brine #1 with different starting pH's at 70C. In a previous submission we reported data for shaker bath tests for brine #1 with starting pH's of 3.5, 4.5 and 5.5. In this submission we these pH's compared to starting brine #1 pH's of 6, and 7.

Characterization of brines and evaporites of Lake Katwe, Uganda

NASA Astrophysics Data System (ADS)

Kasedde, Hillary; Kirabira, John Baptist; Bäbler, Matthäus U.; Tilliander, Anders; Jonsson, Stefan

2014-03-01

Lake Katwe brines and evaporites were investigated to determine their chemical, mineralogical and morphological composition. 30 brine samples and 3 solid salt samples (evaporites) were collected from different locations of the lake deposit. Several analytical techniques were used to determine the chemical composition of the samples including Inductively Coupled Plasma-Atomic Emission Spectrometry (ICP-AES), Inductively Coupled Plasma-Sector Field Mass Spectrometry (ICP-SFMS), ion chromatography, and potentiometric titration. The mineralogical composition and morphology of the evaporites was determined using X-ray diffraction (XRD) and scanning electron microscopy (SEM), respectively. Physical parameters of the lake brines such as density, electrical conductivity, pH, and salinity were also studied. The results show that the lake brines are highly alkaline and rich in Na+, Cl-, CO32-, SO42-, and HCO3- with lesser amounts of K+, Mg2+, Ca2+, Br-, and F- ions. The brines show an intermediate transition between Na-Cl and Na-HCO3 water types. Among the trace metals, the lake brines were found to be enriched in B, I, Sr, Fe, Mo, Ba, and Mn. The solid salts are composed of halite mixed with other salts such as hanksite, burkeite and trona. It was also observed that the composition of the salts varies considerably even within the same grades.

Water Recovery from Brines to Further Close the Water Recovery Loop in Human Spaceflight

NASA Technical Reports Server (NTRS)

Jackson, W. Andrew; Barta, Daniel J.; Anderson, Molly S.; Lange, Kevin E.; Hanford, Anthony J.; Shull, Sarah A.; Carter, D. Layne

2014-01-01

Further closure of water recovery systems will be necessary for future long duration human exploration missions. NASA's Space Technology Roadmap for Human Health, Life Support and Habitation Systems specified a milestone to advance water management technologies during the 2015 to 2019 timeframe to achieve 98% H2O recovery from a mixed wastewater stream containing condensate, urine, hygiene, laundry, and water derived from waste. This goal can only be achieved by either reducing the amount of brines produced by a water recovery system or by recovering water from wastewater brines. NASA convened a Technical Interchange Meeting (TIM) on the topic of Water Recovery from Brines (WRB) that was held on January14-15th, 2014 at Johnson Space Center. Objectives of the TIM were to review systems and architectures that are sources of brines and the composition of brines they produce, review the state of the art in NASA technology development and perspectives from other industries, capture the challenges and difficulties in developing brine processing hardware, identify key figures of merit and requirements to focus technology development and evaluate candidate technologies, and identify other critical issues including microgravity sensitivity, and concepts of operation, safety. This paper represents an initial summary of findings from the workshop.

Perchlorate and nitrate treatment by ion exchange integrated with biological brine treatment.

PubMed

Lehman, S Geno; Badruzzaman, Mohammad; Adham, Samer; Roberts, Deborah J; Clifford, Dennis A

2008-02-01

Groundwater contaminated with perchlorate and nitrate was treated in a pilot plant using a commercially available ion exchange (IX) resin. Regenerant brine concentrate from the IX process, containing high perchlorate and nitrate, was treated biologically and the treated brine was reused in IX resin regeneration. The nitrate concentration of the feed water determined the exhaustion lifetime (i.e., regeneration frequency) of the resin; and the regeneration condition was determined by the perchlorate elution profile from the exhausted resin. The biological brine treatment system, using a salt-tolerant perchlorate- and nitrate-reducing culture, was housed in a sequencing batch reactor (SBR). The biological process consistently reduced perchlorate and nitrate concentrations in the spent brine to below the treatment goals of 500 microg ClO4(-)/L and 0.5mg NO3(-)-N/L determined by equilibrium multicomponent IX modeling. During 20 cycles of regeneration, the system consistently treated the drinking water to below the MCL of nitrate (10 mgNO3(-)-N/L) and the California Department of Health Services (CDHS) notification level of perchlorate (i.e., 6 microg/L). A conceptual cost analysis of the IX process estimated that perchlorate and nitrate treatment using the IX process with biological brine treatment to be approximately 20% less expensive than using the conventional IX with brine disposal.

Chemical composition of selected Kansas brines as an aid to interpreting change in water chemistry with depth

USGS Publications Warehouse

Dingman, R.J.; Angino, E.E.

1969-01-01

Chemical analyses of approximately 1,881 samples of water from selected Kansas brines define the variations of water chemistry with depth and aquifer age. The most concentrated brines are found in the Permian rocks which occupy the intermediate section of the geologic column of this area. Salinity decreases below the Permian until the Ordovician (Arbuckle) horizon is reached and then increases until the Precambrian basement rocks are reached. Chemically, the petroleum brines studied in this small area fit the generally accepted pattern of an increase in calcium, sodium and chloride content with increasing salinity. They do not fit the often-predicted trend of increases in the calcium to chloride ratio, calcium content and salinity with depth and geologic age. The calcium to chloride ratio tends to be asymptotic to about 0.2 with increasing chloride content. Sulfate tends to decrease with increasing calcium content. Bicarbonate content is relatively constant with depth. If many of the hypotheses concerning the chemistry of petroleum brines are valid, then the brines studied are anomolous. An alternative lies in accepting the thesis that exceptions to these hypotheses are rapidly becoming the rule and that indeed we still do not have a valid and general hypothesis to explain the origin and chemistry of petroleum brines. ?? 1969.

Refractive-index measurements in freezing sea-ice and sodium chloride brines.

PubMed

Maykut, G A; Light, B

1995-02-20

Sea ice contains numerous pockets of brine and precipitated salts whose size and number distributions change dramatically with temperature. Theoretical treatment of scattering produced by these inclusions requires information on refractive-index differences among the brine, salts, and surrounding ice. Lacking specific data on refractive-index variations in the brine, we carried out laboratory measurements in freezing-equilibrium solutions between -2 and -32 °C. Index values at 589 nm increased from 1.341 to 1.397 over this temperature range, corresponding to salinities of 35 and 240 parts per thousand (ppt). Spectral data were also taken at 50-nm intervals between 400 and 700 nm in nonequilibrium solutions with salinities ranging up to 300 ppt. Spectral gradients increased slightly with salinity but showed no measurable dependence on temperature between +12 and -16 °C. The Lorentz-Lorenz equation, combined with data on density, molar refractivities, and brine composition, yielded temperature-dependent index predictions in excellent agreement with the experimental data. Similar index and density measurements in freezing sodium chloride brines yielded values nearly identical to those in the sea-ice brines. The absence of mirabilite crystals in sodium chloride ice, however, will cause it to have higher transmissivity and lower reflectivity than sea ice above -22 °C.

Cryogenic formation of brine and sedimentary mirabilite in submergent coastal lake basins, Canadian Arctic

NASA Astrophysics Data System (ADS)

Grasby, Stephen E.; Rod Smith, I.; Bell, Trevor; Forbes, Donald L.

2013-06-01

Two informally named basins (Mirabilite Basins 1 and 2) along a submergent coastline on Banks Island, Canadian Arctic Archipelago, host up to 1 m-thick accumulations of mirabilite (Na2SO4·10H2O) underlying stratified water bodies with basal anoxic brines. Unlike isostatically uplifting coastlines that trap seawater in coastal basins, these basins formed from freshwater lakes that were transgressed by seawater. The depth of the sill that separates the basins from the sea is shallow (1.15 m), such that seasonal sea ice formation down to 1.6 m isolates the basins from open water exchange through the winter. Freezing of seawater excludes salts, generating dense brines that sink to the basin bottom. Progressive freezing increases salinity of residual brines to the point of mirabilite saturation, and as a result sedimentary deposits of mirabilite accumulate on the basin floors. Brine formation also leads to density stratification and bottom water anoxia. We propose a model whereby summer melt of the ice cover forms a temporary freshwater lens, and rather than mixing with the underlying brines, it is exchanged with seawater once the ice plug that separates the basins from the open sea melts. This permits progressive brine development and density stratification within the basins.

Electron-Beam-Pinch Experiment at Harry Diamond Laboratories: Providing for a High-Dose-Rate Flash X-Ray Facility for Transient Radiation Effects on Electronics (TREE) Testing of Pieceparts

DTIC Science & Technology

1991-08-01

The outer perimeter of the converter was attached to the C ring with copper tape. Thermoluminescent dosimeters ( TLDs )* and a coaxial x-ray diode...CaF2) TLDs in Al pillboxes for electronic equilibrium. 7 Figure 2. HIFX beam 400 pinch at 0.05 Torr, Y4 38o in. from face. _360O E 340 d 320 - .~. 300...AD-A239 558Hu D L M-91 -111, 1𔃻, 1 ,11I Aucr,, 1991 Electron -Beam-Pinch Experiment at Harry Diamond Laboratories: Providing for a High-Dose-Rate

Hydrochemical evolution of regional groundwaters to playa brines in central Australia

NASA Astrophysics Data System (ADS)

Jankowski, J.; Jacobson, G.

A large-scale groundwater system in central Australia discharges to a chain of playas. Recharge in calcrete and fractured rock aquifers gives rise to relatively low-salinity HCO 3 Cl SO 4 groundwaters, which evolve through regional saline groundwaters, to highly saline playa brines. The hydrochemical evolution of the groundwaters follows the anionic sequence HCO 3 Cl SO 4 → ClbHCO 3SO 4 → ClSO 4HCO 3 → ClSO 4 → Cl. With increasing salinity, there is a relative increase in Na, K, Mg, Cl and SO 4; however, there is a relative decrease in HCO 3, Ca, and SiO 2 owing to the precipitation of carbonate, sulphate and silicate minerals, and the resultant brines are depleted in these ions. Significant chemical variation in the composition of playa brines is a result of complex processes of solution, evaporative concentration, precipitation and mineralogical change, including dolomitisation. Thermodynamic calculations based on the Pitzer equations have enabled a general model to be developed for these evolutionary processes in saline groundwaters up to the stage of halite saturation. At an early stage the regional groundwaters are saturated with respect to the carbonate minerals, dolomite first, then calcite. With increasing salinity, sulphate minerals begin to precipitate: saturation with respect to gypsum is attained at a chlorinity of 19‰, and saturation with respect to anhydrite is attained at 122‰. The playa brines attain saturation with respect to halite at a chlorinity of 144‰. Solute budgets based on a chloride concentration factor show that final playa brines are 178 times more concentrated than recharge groundwaters, and confirm the virtually complete loss of HCO 3, Ca and SiO 2 through precipitation. There are subtle differences in the hydrochemistry of different central Australian playa brines and also vis-à-vis playa brines described from other parts of the world. Most Australian playas have brines of the ClNa type with SO 4 and Mg also important. The generally accepted Hardie-Eugster model for brine evolution and mineral precipitation sequences has therefore been modified and extended. Three pathways are defined, following calcite precipitation, on the basis of the ratio of molar Ca to alkalinity; these pathways lead to saline waters with different compositions. Subsequent evolution of the brines depends on the ratios between molar SO 4, Mg, Ca and alkalinity.

Fresh Water Generation from Aquifer-Pressured Carbon Storage: Interim Progress Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Aines, R D; Wolery, T J; Hao, Y

2009-07-22

This project is establishing the potential for using brine pressurized by Carbon Capture and Storage (CCS) operations in saline formations as the feedstock for desalination and water treatment technologies including nanofiltration (NF) and reverse osmosis (RO). The aquifer pressure resulting from the energy required to inject the carbon dioxide provides all or part of the inlet pressure for the desalination system. Residual brine would be reinjected into the formation at net volume reduction. This process provides additional storage space (capacity) in the aquifer, reduces operational risks by relieving overpressure in the aquifer, and provides a source of low-cost fresh watermore » to offset costs or operational water needs. Computer modeling and laboratory-scale experimentation are being used to examine mineral scaling and osmotic pressure limitations for brines typical of CCS sites. Computer modeling is being used to evaluate processes in the aquifer, including the evolution of the pressure field. This progress report deals mainly with our geochemical modeling of high-salinity brines and covers the first six months of project execution (September, 2008 to March, 2009). Costs and implementation results will be presented in the annual report. The brines typical of sequestration sites can be several times more concentrated than seawater, requiring specialized modeling codes typical of those developed for nuclear waste disposal calculations. The osmotic pressure developed as the brines are concentrated is of particular concern, as are precipitates that can cause fouling of reverse osmosis membranes and other types of membranes (e.g., NF). We have now completed the development associated with tasks (1) and (2) of the work plan. We now have a contract with Perlorica, Inc., to provide support to the cost analysis and nanofiltration evaluation. We have also conducted several preliminary analyses of the pressure effect in the reservoir in order to confirm that reservoir pressure can indeed be used to drive the reverse osmosis process. Our initial conclusions from the work to date are encouraging: (1) The concept of aquifer-pressured RO to provide fresh water associated with carbon dioxide storage appears feasible. (2) Concentrated brines such as those found in Wyoming are amenable to RO treatment. We have looked at sodium chloride brines from the Nugget Formation in Sublette County. 20-25% removal with conventional methods is realistic; higher removal appears achievable with NF. The less concentrated sulfate-rich brines from the Tensleep Formation in Sublette County would support >80% removal with conventional RO. (3) Brines from other proposed sequestration sites can now be analyzed readily. An osmotic pressure curve appropriate to these brines can be used to evaluate cost and equipment specifications. (4) We have examined a range of subsurface brine compositions that is potentially pertinent to carbon sequestration and noted the principal compositional trends pertinent to evaluating the feasibility of freshwater extraction. We have proposed a general categorization for the feasibility of the process based on total dissolved solids (TDS). (5) Withdrawing pressurized brine can have a very beneficial effect on reservoir pressure and total available storage capacity. Brine must be extracted from a deeper location in the aquifer than the point of CO{sub 2} injection to prevent CO{sub 2} from migrating to the brine extraction well.« less

Water extract of Semecarpus parvifolia Thw. leaves inhibits cell proliferation and induces apoptosis on HEp-2 cells.

PubMed

Soysa, Preethi; Jayarthne, Panchima; Ranathunga, Imali

2018-03-05

Semecarpus parvifolia Thw is used as an ingredient of poly herbal decoctions to treat cancer in traditional medicine. The present study aims to investigate the antiproliferative activity on HEp 2 cells by the water extract of S. parvifolia leaves and to evaluate potential mechanisms. The plant extract was exposed to S. parvifolia for 24 hours and antiproliferative activity was quantified by Sulforhodamine B (SRB), 3-(4, 5-dimethythiazol-2-yl)-2, 5-diphenyl tetrazolium bromide (MTT) and Lactate dehydrogenase (LDH) assays. Morphological changes were observed after staining cells with ethidium bromide/acridine orange (EB/AO) and Giemsa dye. Comet assay was performed to evaluate the DNA damage. The toxicity of the plant extract was determined by brine shrimp lethality assay. S. parvifolia leaves reduced the cell proliferation in a dose and time dependent manner. A two fold increase in NO level was observed at higher concentrations. Morphological changes characteristic to apoptosis were observed in light microscopy, Giemsa and EB/AO stained cells. Fragmented DNA further confirmed its capacity to induce apoptosis. No lethality was observed with brine shrimps. The results suggest that Semecarpus parvifolia Thw induces apoptosis in HEp-2 cells through a NO dependent pathway.

An experimental study of relative permeability hysteresis, capillary trapping characteristics, and capillary pressure of CO2/brine systems at reservoir conditions

NASA Astrophysics Data System (ADS)

Akbarabadi, Morteza

We present the results of an extensive experimental study on the effects of hysteresis on permanent capillary trapping and relative permeability of CO2/brine and supercritical (sc)CO2+SO2/brine systems. We performed numerous unsteady- and steady-state drainage and imbibition full-recirculation flow experiments in three different sandstone rock samples, i.e., low and high-permeability Berea, Nugget sandstones, and Madison limestone carbonate rock sample. A state-of-the-art reservoir conditions core-flooding system was used to perform the tests. The core-flooding apparatus included a medical CT scanner to measure in-situ saturations. The scanner was rotated to the horizontal orientation allowing flow tests through vertically-placed core samples with about 3.8 cm diameter and 15 cm length. Both scCO2 /brine and gaseous CO2 (gCO2)/brine fluid systems were studied. The gaseous and supercritical CO2/brine experiments were carried out at 3.46 and 11 MPa back pressures and 20 and 55°C temperatures, respectively. Under the above-mentioned conditions, the gCO2 and scCO2 have 0.081 and 0.393 gr/cm3 densities, respectively. During unsteady-state tests, the samples were first saturated with brine and then flooded with CO2 (drainage) at different maximum flow rates. The drainage process was then followed by a low flow rate (0.375 cm 3/min) imbibition until residual CO2 saturation was achieved. Wide flow rate ranges of 0.25 to 20 cm3/min for scCO2 and 0.125 to 120 cm3min for gCO2 were used to investigate the variation of initial brine saturation (Swi) with maximum CO2 flow rate and variation of trapped CO2 saturation (SCO2r) with Swi. For a given Swi, the trapped scCO2 saturation was less than that of gCO2 in the same sample. This was attributed to brine being less wetting in the presence of scCO2 than in the presence of gCO 2. During the steady-state experiments, after providing of fully-brine saturated core, scCO2 was injected along with brine to find the drainage curve and as a consequence the Swi, then it was followed by the imbibition process to measure SCO2r. We performed different cycles of relative permeability experiments to investigate the effect of hysteresis. The Swi and SCO2r varied from 0.525 to 0.90 and 0.34 to 0.081, respectively. Maximum CO2 and brine relative permeabilities at the end of drainage and imbibition and also variation of brine relative permeability due to post-imbibition CO2 dissolution during unsteady-state experiment were also studied. We co-injected SO2 with CO2 and brine into the Madison limestone core sample. The sample was acquired from the Rock Springs Uplift in southwest Wyoming. The temperature and pressure of the experiments were 60°C and 19.16 MPa, respectively. Each drainage-imbibition cycle was followed by a dissolution process to establish Sw=1. The results showed that about 76% of the initial CO2 was trapped by capillary trapping mechanism at the end of imbibition test. We also investigated the scCO2+SO2/brine capillary pressure versus saturation relationship through performing primary drainage, imbibition, and secondary drainage experiments. The results indicated that the wettability of the core sample might have been altered owing to being in contact with the scCO 2+SO2/brine system. During primary drainage CO2 displaced 52.5% of brine, i.e., Swi = 0.475. The subsequent imbibition led to 0.329 CO2 saturation. For all series of experiments, the ratio of SCO2r to initial CO2 saturation (1- S wi) was found to be much higher for low initial CO2 saturations. This means that greater fractions of injected CO2 can be permanently trapped at higher initial brine saturations. The results illustrated that very promising fractions (about 49 to 83 %) of the initial CO2 saturation can be trapped permanently. (Abstract shortened by UMI.).

Active CO2 Reservoir Management: A Strategy for Controlling Pressure, CO2 and Brine Migration in Saline-Formation CCS

NASA Astrophysics Data System (ADS)

Buscheck, T. A.; Sun, Y.; Hao, Y.; Court, B.; Celia, M. A.; Wolery, T.; Tompson, A. F.; Aines, R. D.; Friedmann, J.

2010-12-01

CO2 capture and sequestration (CCS) in deep geological formations is regarded as a promising means of lowering the amount of CO2 emitted to the atmosphere and thereby mitigate global warming. The most promising systems for CCS are depleted oil reservoirs, particularly those suited to CO2-based Enhanced Oil Recovery (CCS-EOR), and deep saline formations, both of which are well separated from the atmosphere. For conventional, industrial-scale, saline-formation CCS, pressure buildup can have a limiting effect on CO2 storage capacity. To address this concern, we analyze Active CO2 Reservoir Management (ACRM), which combines brine extraction and residual-brine reinjection with CO2 injection, comparing it with conventional saline-formation CCS. We investigate the influence of brine extraction on pressure response and CO2 and brine migration using the NUFT code. By extracting brine from the lower portion of the storage formation, from locations progressively further from the center of injection, we can counteract buoyancy that drives CO2 to the top of the formation, which is useful in dipping formations. Using “push-pull” manipulation of the CO2 plume, we expose less of the caprock seal to CO2 and more of the storage formation to CO2, with more of the formation utilized for trapping mechanisms. Plume manipulation can also counteract the influence of heterogeneity. We consider the impact of extraction ratio, defined as net extracted brine volume (extraction minus reinjection) divided by injected CO2 volume. Pressure buildup is reduced with increasing extraction ratio, which reduces CO2 and brine migration, increases CO2 storage capacity, and reduces other risks, such as leakage up abandoned wells, caprock fracturing, fault activation, and induced seismicity. For a 100-yr injection period, a 10-yr delay in brine extraction does not diminish the magnitude of pressure reduction. Moreover, it is possible to achieve pressure management with just a few brine-extraction wells, located far from the injection zone. For an extraction ratio of 1, pressure buildup is minimized, greatly reducing the Area of Review, as well as the area required for securing mineral rights. For an extraction ratio of 1, CO2 and brine migration are unaffected by neighboring CO2 operations, which allows planning, assessing, and conducting of each operation to be carried out independently; thus, permits could be granted on a single-site basis. Brine-extraction wells will be useful during monitoring, providing information for system calibration and history matching. One of several key aspects that ACRM has in common with CCS-EOR is the possibility of generating revenue from the extracted fluids; namely, fresh water produced via brine desalination, using technologies such as Reverse Osmosis. These benefits can offset brine extraction and treatment costs, streamline permitting, and help gain public acceptance. This work performed under the auspices of the U.S. Department of Energy by Lawrence Livermore National Laboratory under Contract DE-AC52-07NA27344.

Experimental Work Conducted on MgO Inundated Hydration in WIPP-Relevant Brines

NASA Astrophysics Data System (ADS)

Deng, H.; Xiong, Y.; Nemer, M. B.; Johnsen, S.

2009-12-01

Magnesium oxide (MgO) is being emplaced in the Waste Isolation Pilot Plant (WIPP) as an engineered barrier to mitigate the effect of microbial CO2 generation on actinide mobility in a postclosure repository environment. MgO will sequester CO2 and consume water in brine or water vapor in the gaseous phase. Martin Marietta (MM) MgO is currently being emplaced in the WIPP. A fractional-factorial experiment has been performed to study the inundated-hydration of MM MgO as a function of its particle size, solid-to-liquid ratio, and brine type. MgO hydration experiments have been carried out with three MgO particle sizes and two solid-to-liquid ratios in three WIPP-related brines: ERDA-6, GWB and simplified GWB. ERDA-6 is a synthetic NaCl-rich brine typical of a Castile brine reservoir below the repository. GWB is a synthetic MgCl2- and NaCl-rich brine representative of intergranular brines from the Salado Formation at or near the stratigraphic horizon of the repository. Simplified GWB contains amounts of Mg, Na, and Cl similar to those in GWB without other minor constituents. The hydration products include brucite (Mg(OH)2) and phase 5 (Mg3(OH)5Cl4H2O). In addition to phase 5, MgO hydration in GWB or simplified GWB produces brucite, whereas MgO hydrated in ERDA-6 only produces brucite. The MgO particle size has had a significant effect on the formation of hydration products: small MgO particles have hydrated before the large particles. MgO has hydrated faster in simplified GWB than in the other two brines. In ERDA-6, the solid-to-liquid ratio has affected the brine pH due to the presence of CaO (~1 wt %) as an impurity in MM MgO. GWB has sufficient dissolved Mg to buffer pH despite small amounts of CaO. Both our results and thermodynamic modeling indicate that phase-5 is the stable Mg-OH-Cl phase in Mg-Na-Cl-dominated brines with ionic strengths and chemical compositions similar to that of GWB. In contrast, phase-3 (Mg2(OH)3Cl4H2O) is the stable phase in the MgCl2-saturated Q-brine, a high-ionic-strength (up to 15 m) brine from Asse, Germany. We used EQ3/6 to simulate MgO hydration and carbonation in a closed system containing brine and CO2 at atmospheric concentration by titrating periclase into the system. (EQ3/6 is a geochemical software package for speciation, solubility calculations and reaction path modeling.) EQ3/6 predicted Mg and Cl concentrations and pH similar to the experimentally observed values. EQ3/6 also predicted hydration products similar to thsoe observed experimentally. * This research is funded by WIPP programs administered by the U.S. Department of Energy. ** Sandia is a multiprogram laboratory operated by Sandia Corporation, a Lockheed Martin Company, for the United States Department of Energy’s National Nuclear Security Administration under contract DE-AC04-94AL85000.

Hydrology and surface morphology of the Bonneville Salt Flats and Pilot Valley Playa, Utah

USGS Publications Warehouse

Lines, Gregory C.

1979-01-01

The Bonneville Salt Flats and Pilot Valley are in the western part of the Great Salt Lake Desert in northwest Utah. The areas are separate, though similar, hydrologic basins, and both contain a salt crust. The Bonneville salt crust covered about 40 square miles in the fall of 1976, and the salt crust in Pilot Valley covered 7 square miles. Both areas lack any noticeable surface relief (in 1976, 1.3 feet on the Bonneville salt crust and 0.3 foot on the Pilot Valley salt crust).The salt crust on the Salt Flats has been used for many years for automobile racing, and brines from shallow lacustrine deposits have been used for the production of potash. In recent years, there has been an apparent conflict between these two major uses of the area as the salt crust has diminished in both thickness and extent. Much of the Bonneville Racetrack has become rougher, and there has also been an increase in the amount of sediment on the south end of the racetrack. The Pilot Valley salt crust and surrounding playa have been largely unused.Evaporite minerals on the Salt Flats and the Pilot Valley playa are concentrated in three zones: (1) a carbonate zone composed mainly of authigenic clay-size carbonate minerals, (2) a sulfate zone composed mainly of authigenic gypsum, and (3) a chloride zone composed of crystalline halite (the salt crust). Five major types of salt crust were recognized on the Salt Flats, but only one type was observed in Pilot Valley. Geomorphic differences in the salt crust are caused by differences in their hydrologic environments. The salt crusts are dynamic features that are subject to change because of climatic factors and man's activities.Ground water occurs in three distinct aquifers in much of the western Great Salt Lake Desert: (1) the basin-fill aquifer, which yields water from conglomerate in the lower part of the basin fill, (2) the alluvial-fan aquifer, which yields water from sand and gravel along the western margins of both playas, and (3) the shallow-brine aquifer, which yields water from near-surface carbonate muds and crystalline halite and gypsum. The shallow-brine aquifer is the main source of brine used for the production of potash on the Salt Flats.Recharge to that part of the shallow-brine aquifer north of Interstate Highway 80 on the Salt Flats is mainly by infiltration of precipitation and wind-driven floods of surface brine. Discharge was mainly by evaporation at the playa surface and withdrawals from brine-collection ditches. Some water was transpired by phreatophytes, and some leaked into the alluvial fan along the western edge of the playa.Salt-scraping studies indicate that the amount of halite on the Salt Flats is directly related to the amount of recharge through the surface (which causes re-solution of halite) and the amount of evaporation at the surface (which causes crystallization of halite). Evaporation rates through sediment-covered salt crust and the gypsum surface were estimated at between 3x10-4 and 4x10-3 inches per day during the summer and fall of 1976. Evaporation rates through the surface of thick perennial salt crust were much higher.The concentration of dissolved solids in brine in the shallow-brine aquifer varies, but it generally increases from the edges of the playas toward areas of salt crust. Dissolved-solids concentration in the shallow brine ranges from less than 100,000 to more than 300,000 milligrams per liter on both playas. The increase in salinity toward areas of salt crust reflects the natural direction of brine movement through the aquifer toward the natural discharge area.On the Salt Flats, the percentages of dissolved potassium chloride and magnesium chloride in the shallow-brine aquifer generally increase from the edge of the playa to- ward the salt crust. The relative enrichment in potassium and magnesium reflects the many years of subsurface drainage toward the main discharge area (the salt crust) prior to man's withdrawal of brine. By artificially extracting brines from the carbonate muds, the percentages of potassium and magnesium have decreased while brine salinity has been maintained by re-solution of the salt crust.The configuration of the density-corrected potentiometric surface in the fall of 1976 indicates that brine in the shallow-brine aquifer under the Bonneville Racetrack was draining toward brine-collection ditches or a well field to the west. Ground-water divides have no effect on the movement of dissolved salt across the surface in wind-driven floods, and salt in surface brine was carried from the racetrack into the area of influence of the ditches by such surface movement. During 1976 on the Salt Flats, some brine was moving through the shallow-brine aquifer across lease and property boundaries.An evaluation of suggested remedial measures indicates that none will completely eliminate the conflict between uses or transform the Bonneville Salt Flats to its original state prior to man's activities in the area.

Hydrogen generation by metal corrosion in simulated Waste Isolation Pilot Plant environments. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Telander, M.R.; Westerman, R.E.

1997-03-01

The corrosion and gas-generation characteristics of four material types: low-carbon steel (the current waste packaging material for the Waste Isolation Pilot Plant), Cu-base and Ti-base (alternative packaging) materials, and Al-base (simulated waste) materials were determined in both the liquid and vapor phase of Brine A, a brine representative of an intergranular Salado Formation brine. Test environments consisted primarily of anoxic brine with overpressures of N{sub 2}, CO{sub 2}, H{sub 2}S, and H{sub 2}. Limited tests of low-carbon steel were also performed in simulated-backfill environments and in brine environments with pH values ranging from 3 to 11. Low-carbon steel reacted atmore » a slow, measurable rate with anoxic brine, liberating H{sub 2} on an equimolar basis with Fe reacted. Presence of CO{sub 2} caused the initial reaction to proceed more rapidly, but CO{sub 2}-induced passivation stopped the reaction if the CO{sub 2} were present in sufficient quantities. Addition of H{sub 2}S to a CO{sub 2}-passivated system caused reversal of the passivation. Low-carbon steel immersed in brine with H{sub 2}S showed no reaction, apparently because of passivation of the steel by formation of FeS. Addition of CO{sub 2} to an H{sub 2}S-passivated system did not reverse the passivation. Cu- and Ti-base materials showed essentially no corrosion when exposed to brine and overpressures of N{sub 2}, CO{sub 2}, and H{sub 2}S except for the rapid and complete reaction between Cu-base materials and H{sub 2}S. The Al-base materials reacted at approximately the same rate as low-carbon steel when immersed in anoxic Brine A; considerably more rapidly in the presence of CO{sub 2} or H{sub 2}S; and much more rapidly when iron was present in the system as a brine contaminant. High-purity Al was much more susceptible to corrosion than the 6061 alloy. No significant reaction took place on any material in any environment in the vapor-phase exposures.« less

Terrestrial Gamma-Ray Flashes (TGFs) Above Thunderstorms

NASA Technical Reports Server (NTRS)

Fishman, Gerald J.

2012-01-01

Intense of gamma rays have been observed by five different space-borne detectors. The TGFs have hard spectra, with photons extending to over 50 MeV. Most of these flashes last less than a millisecond. Relativistic electrons and positrons associated with TGFs are also seen by orbiting instruments In a special mode of operation, the Fermi-GBM detectors are now detecting an average of about one TGF every two hours. The Fermi spacecraft has been performing special orientations this year which has allowed the Fermi-LAT instrument also detect TGFs. The most likely origin of these high energy photons is bremsstrahlung radiation from electrons, produced by relativistic runaway electrons in intense electric fields within or above thunderstorm regions; the altitude of origin is uncertain. These TGFs may produce an appreciable radiation dose to passengers and crew in nearby aircraft. The observational aspects of TGFs will be the main focus of this talk; theoretical aspects remain speculative.

Injection-salting of pre rigor fillets of Atlantic salmon (Salmo salar).

PubMed

Birkeland, Sveinung; Akse, Leif; Joensen, Sjurdur; Tobiassen, Torbjørn; Skåra, Torstein

2007-01-01

The effects of temperature (-1, 4, and 10 degrees C), brine concentration (12% and 25% NaCl), injection volumes, and needle densities were investigated on fillet weight gain (%), salt content (%), fillet contraction (%), and muscle gaping in pre rigor brine-injected fillets of Atlantic salmon (Salmo salar). Increased brine concentration (12% to 25%) significantly increased the initial (< 5 min after injection) and final contraction (24 h after injection) of pre rigor fillets. Increased brine concentration significantly reduced weight gain and increased salt content but had no significant effect on muscle gaping. The temperatures tested did not significantly affect weight gain, fillet contraction, or gaping score. Significant regressions (P < 0.01) between the injection volume and weight gain (range: 2.5% to 15.5%) and salt content (range: 1.7% to 6.5%) were observed for injections of pre rigor fillets. Double injections significantly increased the weight gain and salt content compared to single injections. Initial fillet contraction measured 30 min after brine injection increased significantly (P < 0.01) with increasing brine injection volume but no significant difference in the fillet contraction was observed 12 h after brine injection (range: 7.9% to 8.9%). Brine-injected post rigor control fillets obtained higher weight gain, higher salt content, more muscle gaping, and significantly lower fillet contraction compared to the pre rigor injected fillets. Injection-salting is an applicable technology as a means to obtain satisfactory salt contents and homogenously distribute the salt into the muscle of pre rigor fillets of Atlantic salmon before further processing steps such as drying and smoking.

Capillary pressure-saturation relations in quartz and carbonate sands: Limitations for correlating capillary and wettability influences on air, oil, and supercritical CO2 trapping

NASA Astrophysics Data System (ADS)

Wang, Shibo; Tokunaga, Tetsu K.; Wan, Jiamin; Dong, Wenming; Kim, Yongman

2016-08-01

Capillary pressure (Pc)-saturation (Sw) relations are essential for predicting equilibrium and flow of immiscible fluid pairs in soils and deeper geologic formations. In systems that are difficult to measure, behavior is often estimated based on capillary scaling of easily measured Pc-Sw relations (e.g., air-water, and oil-water), yet the reliability of such approximations needs to be examined. In this study, 17 sets of brine drainage and imbibition curves were measured with air-brine, decane-brine, and supercritical (sc) CO2-brine in homogeneous quartz and carbonate sands, using porous plate systems under ambient (0.1 MPa, 23°C) and reservoir (12.0 MPa, 45°C) conditions. Comparisons between these measurements showed significant differences in residual nonwetting phase saturation, Snw,r. Through applying capillary scaling, changes in interfacial properties were indicated, particularly wettability. With respect to the residual trapping of the nonwetting phases, Snwr, CO2 > Snwr, decane > Snwr, air. Decane-brine and scCO2-brine Pc-Sw curves deviated significantly from predictions assuming hydrophilic interactions. Moreover, neither the scaled capillary behavior nor Snw,r for scCO2-brine were well represented by decane-brine, apparently because of differences in wettability and viscosities, indicating limitations for using decane (and other organic liquids) as a surrogate fluid in studies intended to apply to geological carbon sequestration. Thus, challenges remain in applying scaling for predicting capillary trapping and multiphase displacement processes across such diverse fields as vadose zone hydrology, enhanced oil recovery, and geologic carbon sequestration.

Capillary pressure - saturation relations in quartz and carbonate sands: Limitations for correlating capillary and wettability influences on air, oil, and supercritical CO2 trapping

NASA Astrophysics Data System (ADS)

Tokunaga, T. K.; Wang, S.; Wan, J.; Dong, W.; Kim, Y.

2016-12-01

Capillary pressure (Pc) - saturation (Sw) relations are essential for predicting equilibrium and flow of immiscible fluid pairs in soils and deeper geologic formations. In systems that are difficult to measure, behavior is often estimated based on capillary scaling of easily measured Pc-Sw relations (e.g., air-water, and oil-water), yet the reliability of such approximations needs to be examined. In this study, seventeen sets of brine drainage and imbibition curves were measured with air-brine, decane-brine, and supercritical (sc) CO2-brine in homogeneous quartz and carbonate sands, using porous plate systems under ambient (0.1 MPa, 23 °C) and reservoir (12.0 MPa, 45 °C) conditions. Comparisons between these measurements showed significant differences in residual nonwetting phase saturation, Snw,r. Through applying capillary scaling, changes in interfacial properties were indicated, particularly wettability. With respect to the residual trapping of the nonwetting phases, Snwr, CO2 > Snwr, decane > Snwr, air. Decane-brine and scCO2-brine Pc-Sw curves deviated significantly from predictions assuming hydrophilic interactions. Moreover, neither the scaled capillary behavior nor Snw,r for scCO2-brine were well represented by decane-brine, apparently because of differences in wettability and viscosities, indicating limitations for using decane (and other organic liquids) as a surrogate fluid in studies intended to apply to geological carbon sequestration. Thus, challenges remain in applying scaling for predicting capillary trapping and multiphase displacement processes across such diverse fields as vadose zone hydrology, enhanced oil recovery, and geologic carbon sequestration.

Modeling brine and nutrient dynamics in Antarctic sea ice: The case of dissolved silica

NASA Astrophysics Data System (ADS)

Vancoppenolle, Martin; Goosse, Hugues; de Montety, Anne; Fichefet, Thierry; Tremblay, Bruno; Tison, Jean-Louis

2010-02-01

Sea ice ecosystems are characterized by microalgae living in brine inclusions. The growth rate of ice algae depends on light and nutrient supply. Here, the interactions between nutrients and brine dynamics under the influence of algae are investigated using a one-dimensional model. The model includes snow and ice thermodynamics with brine physics and an idealized sea ice biological component, characterized by one nutrient, namely, dissolved silica (DSi). In the model, DSi follows brine motion and is consumed by ice algae. Depending on physical ice characteristics, the brine flow is either advective, diffusive, or turbulent. The vertical profiles of ice salinity and DSi concentration are solutions of advection-diffusion equations. The model is configured to simulate the typical thermodynamic regimes of first-year Antarctic pack ice. The simulated vertical profiles of salinity and DSi qualitatively reproduce observations. Analysis of results highlights the role of convection in the lowermost 5-10 cm of ice. Convection mixes saline, nutrient-poor brine with comparatively fresh, nutrient-rich seawater. This implies a rejection of salt to the ocean and a flux of DSi to the ice. In the presence of growing algae, the simulated ocean-to-ice DSi flux increases by 0-115% compared to an abiotic situation. In turn, primary production and brine convection act in synergy to form a nutrient pump. The other important processes are the flooding of the surface by seawater and the percolation of meltwater. The former refills nutrients near the ice surface in spring. The latter, if present, tends to expell nutrients from the ice in summer.

Brine migration resulting from pressure increases in a layered subsurface system

NASA Astrophysics Data System (ADS)

Delfs, Jens-Olaf; Nordbeck, Johannes; Bauer, Sebastian

2016-04-01

Brine originating from the deep subsurface impairs parts of the freshwater resources in the North German Basin. Some of the deep porous formations (esp. Trias and Jurassic) exhibit considerable storage capacities for waste fluids (CO2, brine from oil production or cavern leaching), raising concerns among water providers that this type of deep subsurface utilization might impair drinking water supplies. On the one hand, overpressures induced by fluid injections and the geothermal gradient support brine migration from deep into shallow formations. On the other hand, the rising brine is denser than the surrounding less-saline formation waters and, therefore, tends to settle down. Aim of this work is to investigate the conditions under which pressurized formation brine from deep formations can reach shallow freshwater resources. Especially, the role of intermediate porous formations between the storage formation and the groundwater is studied. For this, complex thermohaline simulations using a coupled numerical process model are necessary and performed in this study, in which fluid density depends on fluid pressure, temperature and salt content and the governing partial differential equations are coupled. The model setup is 2D and contains a hypothetic series of aquifers and barriers, each with a thickness of 200 m. Formation pressure is increased at depths of about 2000 m in proximity to a salt wall and a permeable fault. The domain size reaches up to tens of kilometers horizontally to the salt wall. The fault connects the injection formation and the freshwater aquifer such that conditions can be considered as extremely favorable for induced brine migration (worst case scenarios). Brine, heat, and salt fluxes are quantified with reference to hydraulic permeabilities, storage capacities (in terms of domain size), initial salt and heat distribution, and operation pressures. The simulations reveal the development of a stagnation point in the fault region in each intermediate aquifer above the injection formation, where brine settles down and flows from the fault zone into the aquifer. This effect changes buoyancy so that lower density brine from the upper aquifers can rise higher and at larger fluxes compared to the case when no intermediary aquifers are present. In general, uplift of brine originating from the intermediary aquifers is mainly restricted to the next overlying two to three permeable aquifers (200m-1000m) or even only to the next aquifer if injection pressures are lower than about 10 bar. If injection induced over-pressures are high, brine from the injection reservoir can dominate inflow into the freshwater reservoir at late times (tens of years). An extensive parameter variation shows the effects of individual parameters. It is found, e.g., that no brine enters the freshwater aquifer if fault permeability is lower than about 10-14 m2. Acknowledgments: This work is part of the ANGUS+ project (www.angusplus.de) and funded by the German Federal Ministry of Education and Research (BMBF) as part of the energy storage initiative "Energiespeicher".

Water Recovery from Brine in the Short and Long Term: A KSC Approach

NASA Technical Reports Server (NTRS)

Lunn, Griffin; Melendez, Orlando; Anthony, Steve

2014-01-01

KSC has spent many years researching Hollow Fiber Membrane Bioreactors as well as research encompassing:Alternate ammonia removal/Advanced oxidation. Brine purification technologies KSC-ISRU has built an electrolysis cell for the removal of acids in ISRU mining brines. Our goal is to combine all such technologies.

Strontium isotopic study of subsurface brines from Illinois basin

DOE Office of Scientific and Technical Information (OSTI.GOV)

hetherington, E.A.; Stueber, A.M.; Pushkar, P.

1986-05-01

The abundance of the radiogenic isotope /sup 87/Sr in a subsurface brine can be used as a tracer of brine origin, evolution, and diagenetic effects. The authors have determined the /sup 87/Sr//sup 86/Sr ratios of over 60 oil-field waters from the Illinois basin, where brine origin is perplexing because of the absence of any significant evaporite strata. Initially, they analyzed brines from 15 petroleum-producing sandstone and carbonate units; waters from Ordovician, Silurian, Devonian, and Mississippian strata have /sup 87/Sr//sup 86/Sr ratios in the range 0.7079-0.7108. All but those from the Ste. Genevieve Limestone (middle Mississippian) are more radiogenic in /supmore » 87/Sr//sup 86/Sr than seawater values for this interval of geologic time. The detrital source of the more radiogenic /sup 87/Sr may be the New Albany Shale group, considered to be a major petroleum source rock in the basin. The /sup 87/Sr//sup 86/Sr ratios of Ste. Genevieve brines apparently evolved without a contribution from fluid-shale interaction.« less

Effects of dry brining, liquid smoking and high-pressure treatment on the physical properties of aquacultured King salmon (Oncorhynchus tshawytscha) during refrigerated storage.

PubMed

Kong, Kelvin Jia Wey; Alçiçek, Zayde; Balaban, Murat O

2015-03-15

Aquacultured King salmon (Oncorhynchus tshawytscha) pieces were dry brined with a salt/brown sugar mix, dipped in liquid smoke for 3 min, vacuum packed, high hydrostatic pressure (HHP) treated at 600 or 200 MPa for 5 min and stored at 4 °C for up to 40 days. The surface redness (average a*) of the samples increased after dry brining, then decreased after liquid smoke treatment. HHP did not change the outside color of liquid-smoked samples. However, the inside color changed depending on pressure. HHP-treated control samples without dry brining and liquid smoking changed to a pale pink color. HHP at 600 MPa resulted in a significant increase in hardness. Compared with fresh samples, dry-brined samples had reduced water activity, while samples dipped in liquid smoke had lower pH values. Dry brining and liquid smoking protect the outside color of salmon against changes caused by HHP. The increase in hardness may counteract the softening of the smoked salmon tissue over time. © 2014 Society of Chemical Industry.

Uncertainty and sensitivity analysis for two-phase flow in the vicinity of the repository in the 1996 performance assessment for the Waste Isolation Pilot Plant: Disturbed conditions

DOE Office of Scientific and Technical Information (OSTI.GOV)

HELTON,JON CRAIG; BEAN,J.E.; ECONOMY,K.

2000-05-22

Uncertainty and sensitivity analysis results obtained in the 1996 performance assessment (PA) for the Waste Isolation Pilot Plant (WIPP) are presented for two-phase flow in the vicinity of the repository under disturbed conditions resulting from drilling intrusions. Techniques based on Latin hypercube sampling, examination of scatterplots, stepwise regression analysis, partial correlation analysis and rank transformations are used to investigate brine inflow, gas generation repository pressure, brine saturation and brine and gas outflow. Of the variables under study, repository pressure and brine flow from the repository to the Culebra Dolomite are potentially the most important in PA for the WIPP. Subsequentmore » to a drilling intrusion repository pressure was dominated by borehole permeability and generally below the level (i.e., 8 MPa) that could potentially produce spallings and direct brine releases. Brine flow from the repository to the Culebra Dolomite tended to be small or nonexistent with its occurrence and size also dominated by borehole permeability.« less

Effects of energy development on wetland plants and macroinvertebrate communities in Prairie Pothole Region wetlands

USGS Publications Warehouse

Preston, Todd M.; Ray, Andrew M.

2016-01-01

Energy production in the Williston Basin, USA, results in the coproduction of highly saline, sodium chloride-dominated water (brine). The Prairie Pothole Region (PPR) overlies the northeastern portion of the Williston Basin. Although PPR wetlands span a range of salinity, the dominant salt is sodium sulfate, and salinities are much lower than brine. Introduction of brine to wetlands can result in pronounced water-quality changes; however, the ecological effects of such contamination are poorly understood. We examined the effects of brine contamination on primary productivity, emergent macrophyte tissue chemistry, and invertebrate communities from 10 wetlands in the PPR. Based on a recognized Contamination Index (CI) used to identify brine contamination in the PPR, water-quality samples indicated that six wetlands were uncontaminated while four were contaminated. Across this gradient, we observed a significant decrease in above-ground biomass and a significant increase in tissue chloride concentrations of hardstem bulrush (Schoenoplectus acutus) with increased CI values. Additionally, a significant decrease in macroinvertebrate taxonomic richness with increased CI values was observed. These findings provide needed insight on the biological effects of brine contamination on PPR wetlands.

A study of antimicrobial activity, acute toxicity and cytoprotective effect of a polyherbal extract in a rat ethanol-HCl gastric ulcer model

PubMed Central

2012-01-01

Background The decoction of the aerial parts of Rhynchosia recinosa (A.Rich.) Bak. [Fabaceae] is used in combination with the stem barks of Ozoroa insignis Del. (Anacardiaceae), Maytenus senegalensis (Lam.) Excell. [Celastraceae] Entada abyssinica Steud. ex A.Rich [Fabaceae] and Lannea schimperi (Hochst.)Engl. [Anacardiaceae] as a traditional remedy for managing peptic ulcers. However, the safety and efficacy of this polyherbal preparation has not been evaluated. This study reports on the phytochemical profile and some biological activities of the individual plant extracts and a combination of extracts of the five plants. Methods A mixture of 80% ethanol extracts of R. recinosa, O. insignis, M. senegalensis, E. abyssinica and L. schimperi at doses of 100, 200, 400 and 800 mg/kg body wt were evaluated for ability to protect Sprague Dawley rats from gastric ulceration by an ethanol-HCl mixture. Cytoprotective effect was assessed by comparison with a negative control group given 1% tween 80 in normal saline and a positive control group given 40 mg/kg body wt pantoprazole. The individual extracts and their combinations were also tested for antibacterial activity against four Gram negative bacteria; Escherichia coli (ATCC 25922), Salmonella typhi (NCTC 8385), Vibrio cholerae (clinical isolate), and Klebsiella pneumoniae (clinical isolate) using the microdilution method. In addition the extracts were evaluated for brine shrimp toxicity and acute toxicity in mice. Phytochemical tests were done using standard methods to determine the presence of tannins, saponins, steroids, cardiac glycosides, flavonoids, alkaloids and terpenoids in the individual plant extracts and in the mixed extract of the five plants. Results The combined ethanolic extracts of the 5 plants caused a dose-dependent protection against ethanol/HCl induced ulceration of rat gastric mucosa, reaching 81.7% mean protection as compared to 87.5% protection by 40 mg/kg body wt pantoprazole. Both the individual plant extracts and the mixed extracts of 5 plants exhibited weak to moderate antibacterial activity against four G-ve bacteria. Despite Ozoroa insignis being toxic to mice at doses above 1000 mg/kg body wt, the other plant extracts and the combined extract of the 5 plants were tolerated by mice up to 5000 mg/kg body wt. The brine shrimp test results showed the same pattern of toxicity with Ozoroa insignis being the most toxic (LC50 = 10.63 μg/ml). Phytochemical tests showed that the combined extract of the five plants contained tannins, saponins, steroids, cardiac glycosides, flavonoids and terpenoids. Flavonoids, tannins and terpenoids are known to have antioxidant activity. Conclusion The combined extract of the five plants exhibited a dose-dependent protective activity in the rat ethanol-HCl gastric ulcer model. The extracts also exhibited weak antibacterial activity against four Gram negative bacteria and low acute toxicity in mice and brine shrimps. Although the results support claims by traditional healers who use a decoction of the five plants for treatment of peptic ulcers, more models of gastric ulceration and proper animal toxicity studies are needed to validate possible clinical use of the polyherbal extract. It is also evident that the doses of the crude extracts showing protection of the gastric mucosa are too large for realistic translation to direct clinical application, but further studies using bioassay guided fractionation are important to either identify more practical fractions or active compound/s. PMID:23031266

Prediction of halite, gypsum, and anhydrite solubility in natural brines under subsurface conditions

NASA Astrophysics Data System (ADS)

He, Shiliang; Morse, John W.

1993-01-01

Prediction of the solubility of the evaporite minerals halite, gypsum, and anhydrite in brines has numerous scientific and practical applications. This paper presents a Pitzer equation-based model for predicting the solubility of these minerals in Na +-K +-H +-Ca 2+-Mg 2+-Cl --OH --SO 42--H 2O solutions of varying composition as a function of temperature and pressure. Model predictions compare well with experimental observations. As an example of the utility of this program, the volume of CaSO 4 precipitated as a brine flows up a pipe from 6000 m depth is predicted. This is done as a function of flow distance for different cooling rates of the brine. Results indicate that if the brine can be cooled to near the geothermal gradient no precipitation will take place.

The influence of closed brine pockets and permeable brine channels on the thermo-elastic properties of saline ice

PubMed Central

Lishman, Ben

2017-01-01

A model of the thermo-elastic behaviour of saline ice is formulated, and model solutions describing thermo-elastic waves (TEW) propagating into a half-space of the ice are investigated. The model is based on a proposal that saline ice is a matrix, which encompasses both closed brine pockets and permeable channels filled with brine. Experiments on the thermal expansion of saline ice samples, and on TEW in saline ice, have been performed in the cold laboratories of the University Centre in Svalbard and in University College London. The experimental data are compared with theoretical conclusions. The experimental data support our hypothesis that the brine in saline ice is divided between closed pockets and open, permeable channels. This article is part of the themed issue ‘Microdynamics of ice’. PMID:28025299

Extreme 13C depletions in seawater-derived brines and their implications for the past geochemical carbon cycle

NASA Astrophysics Data System (ADS)

Lazar, Boaz; Erez, Jonathan

1990-12-01

Extreme depletions in the 13C content of the total dissolved inorganic carbon (CT) were found in brines overlying microbial mat communities. Total alkalinity (AT) and CT in the brines suggest that intense photosynthetic activity of the microbial mat communities depletes the CT from the brine. We suggest that this depletion drives a large, kinetic, negative fractionation of carbon isotopes similar to that observed in highly alkaline solutions. In brines of extreme salinity where microbial mat communities no longer exist, the 13C content of the CT increases, probably because photosynthesis no longer dominates the gas-exchange processes. This mechanism explains light carbon-isotope compositions of carbonate rocks from evaporitic sections and bears on the interpretation of δ13C values in bedded stromatolitic limestones that are ca. 3.5 b.y. old.

Life cycle assessment of treatment and handling options for a highly saline brine extracted from a potential CO2 storage site.

PubMed

Salih, Hafiz H; Li, Jiaxing; Kaplan, Ruth; Dastgheib, Seyed A

2017-10-01

Carbon dioxide (CO 2 ) injection in deep saline aquifers is a promising option for CO 2 geological sequestration. However, brine extraction may be necessary to control the anticipated increase in reservoir pressure resulting from CO 2 injection. The extracted brines usually have elevated concentrations of total dissolved solids (TDS) and other contaminants and require proper handling or treatment. Different options for the handling or treatment of a high-TDS brine extracted from a potential CO 2 sequestration site (Mt. Simon Sandstone, Illinois, USA) are evaluated here through a life cycle assessment (LCA) study. The objective of this LCA study is to evaluate the environmental impact (EI) of various treatment or disposal options, namely, deep well disposal (Case 1); near-zero liquid discharge (ZLD) treatment followed by disposal of salt and brine by-products (Case 2); and near-ZLD treatment assuming beneficial use of the treatment by-products (Case 3). Results indicate that energy use is the dominant factor determining the overall EI. Because of the high energy consumption, desalination of the pretreated brine (Cases 2 and 3) results in the highest EI. Consequently, the overall EI of desalination cases falls mainly into two EI categories: global warming potential and resources-fossil fuels. Deep well disposal has the least EI when the EI of brine injection into deep formations is not included. The overall freshwater consumption associated with different life cycle stages of the selected disposal or treatment options is 0.6-1.8 m 3 of freshwater for every 1.0 m 3 of brine input. The freshwater consumption balance is 0.6 m 3 for every 1.0 m 3 of brine input for Case 3 when desalination by-products are utilized for beneficial uses. Copyright © 2017 Elsevier Ltd. All rights reserved.

Jarosite dissolution rates in perchlorate brine

NASA Astrophysics Data System (ADS)

Legett, Carey; Pritchett, Brittany N.; Elwood Madden, Andrew S.; Phillips-Lander, Charity M.; Elwood Madden, Megan E.

2018-02-01

Perchlorate salts and the ferric sulfate mineral jarosite have been detected at multiple locations on Mars by both landed instruments and orbiting spectrometers. Many perchlorate brines have eutectic temperatures <250 K, and may exist as metastable or stable liquids for extended time periods, even under current Mars surface conditions. Therefore, jarosite-bearing rocks and sediments may have been altered by perchlorate brines. Here we measured jarosite dissolution rates in 2 M sodium perchlorate brine as well as dilute water at 298 K to determine the effects of perchlorate anions on jarosite dissolution rates and potential reaction products. We developed a simple method for determining aqueous iron concentrations in high salinity perchlorate solutions using ultraviolet-visible spectrophotometry that eliminates the risk of rapid oxidation reactions during analyses. Jarosite dissolution rates in 2 M perchlorate brine determined by iron release rate (2.87 × 10-12 ±0.85 × 10-12 mol m-2 s-1) were slightly slower than the jarosite dissolution rate measured in ultrapure (18.2 MΩ cm-1) water (5.06 × 10-12 mol m-2 s-1) using identical methods. No additional secondary phases were observed in XRD analyses of the reaction products. The observed decrease in dissolution rate may be due to lower activity of water (ɑH2O = 0.9) in the 2 M NaClO4 brine compared with ultrapure water (ɑH2O = 1). This suggests that the perchlorate anion does not facilitate iron release, unlike chloride anions which accelerated Fe release rates in previously reported jarosite and hematite dissolution experiments. Since dissolution rates are slower in perchlorate-rich solutions, jarosite is expected to persist longer in perchlorate brines than in dilute waters or chloride-rich brines. Therefore, if perchlorate brines dominate aqueous fluids on the surface of Mars, jarosite may remain preserved over extended periods of time, despite active aqueous processes.

Effects of brine contamination from energy development on wetland macroinvertebrate community structure in the Prairie Pothole Region.

PubMed

Preston, Todd M; Borgreen, Michael J; Ray, Andrew M

2018-08-01

Wetlands in the Prairie Pothole Region (PPR) of North America support macroinvertebrate communities that are integral to local food webs and important to breeding waterfowl. Macroinvertebrates in PPR wetlands are primarily generalists and well adapted to within and among year changes in water permanence and salinity. The Williston Basin, a major source of U.S. energy production, underlies the southwest portion of the PPR. Development of oil and gas results in the coproduction of large volumes of highly saline, sodium chloride dominated water (brine) and the introduction of brine can alter wetland salinity. To assess potential effects of brine contamination on macroinvertebrate communities, 155 PPR wetlands spanning a range of hydroperiods and salinities were sampled between 2014 and 2016. Brine contamination was documented in 34 wetlands with contaminated wetlands having significantly higher chloride concentrations, specific conductance and percent dominant taxa, and significantly lower taxonomic richness, Shannon diversity, and Pielou evenness scores compared to uncontaminated wetlands. Non-metric multidimensional scaling found significant correlations between several water quality parameters and macroinvertebrate communities. Chloride concentration and specific conductance, which can be elevated in naturally saline wetlands, but are also associated with brine contamination, had the strongest correlations. Five wetland groups were identified from cluster analysis with many of the highly contaminated wetlands located in a single cluster. Low or moderately contaminated wetlands were distributed among the remaining clusters and had macroinvertebrate communities similar to uncontaminated wetlands. While aggregate changes in macroinvertebrate community structure were observed with brine contamination, systematic changes were not evident, likely due to the strong and potentially confounding influence of hydroperiod and natural salinity. Therefore, despite the observed negative response of macroinvertebrate communities to brine contamination, macroinvertebrate community structure alone is likely not the most sensitive indicator of brine contamination in PPR wetlands. Copyright © 2018 Elsevier Ltd. All rights reserved.

Why Flash Type Matters: A Statistical Analysis

NASA Astrophysics Data System (ADS)

Mecikalski, Retha M.; Bitzer, Phillip M.; Carey, Lawrence D.

2017-09-01

While the majority of research only differentiates between intracloud (IC) and cloud-to-ground (CG) flashes, there exists a third flash type, known as hybrid flashes. These flashes have extensive IC components as well as return strokes to ground but are misclassified as CG flashes in current flash type analyses due to the presence of a return stroke. In an effort to show that IC, CG, and hybrid flashes should be separately classified, the two-sample Kolmogorov-Smirnov (KS) test was applied to the flash sizes, flash initiation, and flash propagation altitudes for each of the three flash types. The KS test statistically showed that IC, CG, and hybrid flashes do not have the same parent distributions and thus should be separately classified. Separate classification of hybrid flashes will lead to improved lightning-related research, because unambiguously classified hybrid flashes occur on the same order of magnitude as CG flashes for multicellular storms.

Ring Resonator for Detection of Melting Brine Under Shallow Subsurface of Mars

NASA Technical Reports Server (NTRS)

Ponchak, George E.; Jordan, Jennifer L.; Scardelletti, Maximillian C.

2016-01-01

Laboratory experimental evidence using Raman spectroscopy has shown that liquid brine may form below the shallow subsurface of Mars. A simpler experimental method to verify the presence of liquid brine or liquid water below Mars surface is needed. In this paper, a ring resonator is used to detect the phase change between frozen water and liquid water below a sandy soil that simulates the Mars surface. Experimental data shows that the ring resonator can detect the melting of thin layers of frozen brine or water up to 15 mm below the surface.

Magnesium compounds

USGS Publications Warehouse

Kramer, D.A.

2010-01-01

Seawater and natural brines accounted for about 40 percent of U.S. magnesium compounds production in 2009. Dead-burned magnesia was produced by Martin Marietta Magnesia Specialties from well brines in Michigan. Caustic-calcined magnesia was recovered from seawater by Premier Chemicals in Florida, from well brines in Michigan by Martin Marietta and from magnesite in Nevada by Premier Chemicals. Intrepid Potash-Wendover, and Great Salt Lake Minerals Corp. recovered magnesium chloride brines from the Great Salt Lake in Utah. Magnesium hydroxide was produced from seawater by SPI Pharma in Delaware and Premier Chemicals in Florida, and by Martin Marietta from its operation mentioned above.

Magnesium compounds

USGS Publications Warehouse

Kramer, D.A.

2011-01-01

Seawater and natural brines accounted for about 54 percent of U.S. magnesium compounds production in 2010. Dead-burned magnesia was produced by Martin Marietta Magnesia Specialties from well brines in Michigan. Caustic-calcined magnesia was recovered from seawater by Premier Magnesia in Florida, from well brines in Michigan by Martin Marietta and from magnesite in Nevada by Premier Magnesia. Intrepid Potash-Wendover and Great Salt Lake Minerals Corp. recovered magnesium chloride brines from the Great Salt Lake in Utah. Magnesium hydroxide was produced from seawater by SPI Pharma in Delaware and Premier Magnesia in Florida, and by Martin Marietta from its operation mentioned above.

Brine rejection from freezing salt solutions: a molecular dynamics study.

PubMed

Vrbka, Lubos; Jungwirth, Pavel

2005-09-30

The atmospherically and technologically very important process of brine rejection from freezing salt solutions is investigated with atomic resolution using molecular dynamics simulations. The present calculations allow us to follow the motion of each water molecule and salt ion and to propose a microscopic mechanism of brine rejection, in which a fluctuation (reduction) of the ion density in the vicinity of the ice front is followed by the growth of a new ice layer. The presence of salt slows down the freezing process, which leads to the formation of an almost neat ice next to a disordered brine layer.

Qualitative and quantitative changes in detrital reservoir rocks caused by CO2-brine-rock interactions during first injection phases (Utrillas sandstones, northern Spain)

NASA Astrophysics Data System (ADS)

Berrezueta, E.; Ordóñez-Casado, B.; Quintana, L.

2016-01-01

The aim of this article is to describe and interpret qualitative and quantitative changes at rock matrix scale of lower-upper Cretaceous sandstones exposed to supercritical (SC) CO2 and brine. The effects of experimental injection of CO2-rich brine during the first injection phases were studied at rock matrix scale, in a potential deep sedimentary reservoir in northern Spain (Utrillas unit, at the base of the Cenozoic Duero Basin).

Experimental CO2-rich brine was exposed to sandstone in a reactor chamber under realistic conditions of deep saline formations (P ≈ 7.8 MPa, T ≈ 38 °C and 24 h exposure time). After the experiment, exposed and non-exposed equivalent sample sets were compared with the aim of assessing possible changes due to the effect of the CO2-rich brine exposure. Optical microscopy (OpM) and scanning electron microscopy (SEM) aided by optical image analysis (OIA) were used to compare the rock samples and get qualitative and quantitative information about mineralogy, texture and pore network distribution. Complementary chemical analyses were performed to refine the mineralogical information and to obtain whole rock geochemical data. Brine composition was also analyzed before and after the experiment.

The petrographic study of contiguous sandstone samples (more external area of sample blocks) before and after CO2-rich brine injection indicates an evolution of the pore network (porosity increase ≈ 2 %). It is probable that these measured pore changes could be due to intergranular quartz matrix detachment and partial removal from the rock sample, considering them as the early features produced by the CO2-rich brine. Nevertheless, the whole rock and brine chemical analyses after interaction with CO2-rich brine do not present important changes in the mineralogical and chemical configuration of the rock with respect to initial conditions, ruling out relevant precipitation or dissolution at these early stages to rock-block scale. These results, simulating the CO2 injection near the injection well during the first phases (24 h) indicate that, in this environment where CO2 enriches the brine, the mixture principally generates local mineralogical/textural re-adjustments on the external area of the samples studied.

The application of OpM, SEM and optical image analysis have allowed an exhaustive characterization of the sandstones studied. The procedure followed, the porosity characterization and the chemical analysis allowed a preliminary approximation of the CO2-brine-rock interactions and could be applied to similar experimental injection tests.

Controls on the pH of hyper-saline lakes - A lesson from the Dead Sea

NASA Astrophysics Data System (ADS)

Golan, Rotem; Gavrieli, Ittai; Ganor, Jiwchar; Lazar, Boaz

2016-01-01

The pH of aqueous environments is determined by the dominant buffer systems of the water, defined operationally as total alkalinity (TA). The major buffer systems in the modern ocean are carbonic and boric acids of which the species bicarbonate, carbonate and borate make up about 77%, 19% and 4% of the TA, respectively. During the course of seawater evaporation (e.g. lagoons) the residual brine loses considerable portion of the dissolved inorganic carbon (DIC) and carbonate alkalinity (CA) already at the early stages of evaporation. DIC and CA decrease due to massive precipitation of CaCO3, while total boron (TB) increases conservatively, turning borate to the dominant alkalinity species in marine derived brines. In the present work we assess the apparent dissociation constant value of boric acid (KB‧) in saline and hypersaline waters, using the Dead Sea (DS) as a case study. We explain the DS low pH (∼6.3) and the effect of the boric and carbonic acid pK‧-s on the behavior of the brine's buffer system, including the pH increase that results from brine dilution. The KB‧ in DS was estimated from TB, TA, DIC and pH data measured in this study and early empirical data on artificial DS brines containing just carbonic acid. The KB‧ value was corroborated by Pitzer ion interaction model calculations using PHREEQC thermodynamic code applied to the chemical composition of the DS. Our results show that KB‧ increases considerably with the brine's ionic strength, reaching in the DS to a factor of 100 higher than in ;mean; seawater. Based on theoretical calculations and analyses of other natural brines it is suggested that brines' composition is a major factor in determining the KB‧ value and in turn the pH of such brines. We show that the higher the proportion of divalent cations in the brine the higher the dissociation constants of the weak acids (presumably due to formation of complexes). The low pH of the Dead Sea is accordingly explained by its extremely high ionic strength (TDS = 348 g/L) and the dominance of the divalent cation, Mg2+. Other natural hyper-saline brines with high concentration of divalent cations such as Kunteyi Lake in China and Don-Juan Pond in Antarctica follow the same general pattern. In contrast, the high pH of soda lakes results not only from their high TA but also by the dominance of the monovalent cation, Na+. Our study emphasizes the strong control of brine composition on pKB‧ and pH. These factors should be taken into consideration when reconstructing past and present environmental evaporitic environments.

Mechanisms of sulfate removal from subsurface calcium chloride brines: Heletz-Kokhav oilfields, Israel

NASA Astrophysics Data System (ADS)

Gavrieli, Ittai; Starinsky, Avraham; Spiro, Baruch; Aizenshtat, Zeev; Nielsen, Heimo

1995-09-01

The evolution of the Ca-chloride brines in the Heletz Formation, Lower Cretaceous, in the southern coastal plain of Israel was reconstructed through the study of its sulfate concentration and isotopic composition. Particular emphasis was given to the brine-oil interaction in the oilfields and to the sulfate depletion and lower SO 4/Cl ratio in brines in contact with hydrocarbons (oil brines) relative to "oil-free" from dry wells in the same oilfields. A method is presented for a calculation of the amount of sulfate removed from the original seawater in the various stages of its evolution to Ca-chloride brine. These stages include evaporation, dolomitization, and sulfate reduction in different stages of its evolution, from early diagenetic processes to the contact with crude oil. In the present study, based on the δ34S SO 4 and SO 4/Cl ratio, it was found that in the Heletz brines most of the sulfate (80-94%) was removed from the original seawater prior to their interaction with the hydrocarbons and only a negligible fraction of few percent of the sulfate was removed during the crude oil-water contact. The Ca-chloride brines evolved from Messinian (Upper Miocene) seawater that underwent evaporation during the desiccation of the Mediterranean. Sulfate was removed from Messinian lagoon (s) during gypsum precipitation due to evaporation and dolomitization. Bacterial sulfate reduction further depleted the brine in sulfate and changed its isotopic composition, from its original Miocene seawater composition of δ34S SO 4 ˜ 20%o, 26%o. Overall, some 50% of the original sulfate, as normalized to chloride, was removed from the original lagoon through the above processes, mostly by gypsum precipitation. Eastward migration of the Messinian Ca-Chloride brine into the Heletz Formation was accompanied by dolomitization of the country rock. Final depletion of sulfate from the brines took place, and possibly still occurs, in the presence of crude oil in the oilfields. The two oil-producing fields, Heletz and Kokhav, occupy different areas on a Rayleigh distillation diagram. Sulfate depletion in both fields is accompanied by an increase in δ34S SO 4, which reaches a maximum value of 59%o. The above correlation is explained by bacterial sulfate reduction facilitated by the contact with the crude. Samples collected from the same boreholes at time intervals of several months show two opposing trends: sulfate concentration decrease accompanied by increase in δ34S SO 4, and vice versa. While the first can be explained as in situ bacterial sulfate reduction, the latter attest to subsurface brine migration, as would be expected in oil-producing fields.

An Experimental Study of CO2-Brine Relative Permeability in Sandstone

NASA Astrophysics Data System (ADS)

Chen, X.; DiCarlo, D. A.

2013-12-01

Accurate determinations of CO2-brine relative permeability are important for modeling potential CO2 storage scenarios. The most common assumption is that CO2-brine relative permeability is likely to be similar to oil-brine relative permeability for water-wet rocks. But recent measurements of CO2-brine relative permeability have differed greatly from oil-brine relative permeability; particularly, the measurements show a very low CO2 end point relative permeability (kr,CO2=0.1~0.2) and a relatively high residual water saturation (Swr>0.4) ( Lee et al. 2010, Zuo et al. 2012, Akbarabadi et al. 2013 and etc.). It has been hypothesized that the differences are related to CO2-brine having a different contact angle from oil-brine. In this study, we hypothesize that the differences are caused by large capillary end effects resulted from the very low CO2 viscosity. We conduct steady-state CO2-brine flow experiments in 2-foot-long and 2.8-inch-diamter Berea sandstone cores at 20 °C and 1500 psi. Four pressure taps drilled on a core allow both the total pressure drop and that across five individual sections to be measured. Three experiments, two drainage and one imbibition, have been conducted so far. Our results show: (1) The relative permeability to both brine and CO2 of the last section (downstream, 15 cm long) is significantly smaller than that of any of the middle three sections. This testifies that the capillary end effect makes the relative permeability under-measured at the end of a core. (2) The values of the middle three sections are very close to each other, which indicate the middle part of our core is free of capillary end effect. (3) The CO2 end point relative permeability is 0.3~0.5, which is much higher than the recent measurements. (4) The brine end point relative permeability during imbibition is about 0.08, which is close to literature data. Reference: Lee, Y.S, Kim, K. H. and Lee, T.H. et al. Analysis of CO2 Endpoint Relative Permeability and Injectivity by Change in Pressure, Temperature, and Phase in Saline Aquifer, 2010 Energy Sources, Part A, 32: 83-99 Zuo, L., Krevor, S. and Falta, R. W. et al. An experimental study of CO2 exsolution and relative permeability measurements during CO2 saturated water depressurization. Transport in Porous Media, 2012, 91: 459-478 Akbarabadi, M. and Piri, M. Relative permeability hysteresis and capillary trapping characteristics of supercritical CO2/brine systems: an experimental study at reservoir conditions. Advances in Water Resources, 2013 52: 190-206

Space-Borne Observations of Intense Gamma-Ray Flashes (TGFs) Above Thunderstorms

NASA Technical Reports Server (NTRS)

Fishman, Gerald J.

2010-01-01

Intense millisecond flashes of MeV photons are being observed with space-borne detectors. These terrestrial gamma-ray flashes (TGFs) were discovered with the Burst and Transient Source Experiment (BATSE) aboard the Compton Gamma-Ray Observatory (CGRO) in the early 1990s. They are now being observed with several other instruments, including the Gamma-ray Burst Monitor (GBM) detectors on the Fermi Gamma-ray Space Telescope. Although Fermi-GBM was designed and optimized for the observation of cosmic gamma-ray bursts (GRBs), it has unprecedented capabilities for TGF observations. The TGFs usually have extremely hard continuous spectra, typical of highly-Comptonized bremsstrahlung radiation. These spectral are harder than those of GRBs, with photons extending to over 40 MeV. The most likely origin of these high-energy photons is bremsstrahlung radiation produced by a relativistic runaway avalanche electron beam. Such a beam is expected to be produced in an extended, intense electric field in or above thunderstorm regions. The altitude of origin and beaming characteristics of the radiation are quite uncertain. These TGFs may produce an appreciable radiation dose to passengers and crew in nearby aircraft. They have generated considerable observational and theoretical interest in recent years. Instruments are being designed specifically for TGF observations from new spacecraft as well as from airborne platforms.

Integrated CO 2 Storage and Brine Extraction

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hunter, Kelsey; Bielicki, Jeffrey M.; Middleton, Richard

Carbon dioxide (CO 2) capture, utilization, and storage (CCUS) can reduce CO 2 emissions from fossil fuel power plants by injecting CO 2 into deep saline aquifers for storage. CCUS typically increases reservoir pressure which increases costs, because less CO 2 can be injected, and risks such as induced seismicity. Extracting brine with enhanced water recovery (EWR) from the CO 2 storage reservoir can manage and reduce pressure in the formation, decrease the risks linked to reservoir overpressure (e.g., induced seismicity), increase CO 2 storage capacity, and enable CO 2 plume management. We modeled scenarios of CO 2 injection withmore » EWR into the Rock Springs Uplift (RSU) formation in southwest Wyoming. The Finite Element Heat and Mass Transfer Code (FEHM) was used to model CO 2 injection with brine extraction and the corresponding increase in pressure within the RSU. We analyzed the model for pressure management, CO 2 storage, CO 2 saturation, and brine extraction due to the quantity and location of brine extraction wells. The model limited CO 2 injection to a constant pressure increase of two MPa at the injection well with and without extracting brine at hydrostatic pressure. Finally, we found that brine extraction can be used as a technical and cost-effective pressure management strategy to limit reservoir pressure buildup and increase CO 2 storage associated with a single injection well.« less

Integrated CO 2 Storage and Brine Extraction

DOE PAGES

Hunter, Kelsey; Bielicki, Jeffrey M.; Middleton, Richard; ...

2017-08-18

Carbon dioxide (CO 2) capture, utilization, and storage (CCUS) can reduce CO 2 emissions from fossil fuel power plants by injecting CO 2 into deep saline aquifers for storage. CCUS typically increases reservoir pressure which increases costs, because less CO 2 can be injected, and risks such as induced seismicity. Extracting brine with enhanced water recovery (EWR) from the CO 2 storage reservoir can manage and reduce pressure in the formation, decrease the risks linked to reservoir overpressure (e.g., induced seismicity), increase CO 2 storage capacity, and enable CO 2 plume management. We modeled scenarios of CO 2 injection withmore » EWR into the Rock Springs Uplift (RSU) formation in southwest Wyoming. The Finite Element Heat and Mass Transfer Code (FEHM) was used to model CO 2 injection with brine extraction and the corresponding increase in pressure within the RSU. We analyzed the model for pressure management, CO 2 storage, CO 2 saturation, and brine extraction due to the quantity and location of brine extraction wells. The model limited CO 2 injection to a constant pressure increase of two MPa at the injection well with and without extracting brine at hydrostatic pressure. Finally, we found that brine extraction can be used as a technical and cost-effective pressure management strategy to limit reservoir pressure buildup and increase CO 2 storage associated with a single injection well.« less

Assessment of desalination technologies for treatment of a highly saline brine from a potential CO 2 storage site

DOE PAGES

Kaplan, Ruth; Mamrosh, Darryl; Salih, Hafiz H.; ...

2016-11-12

Brine extraction is a promising strategy for the management of increased reservoir pressure, resulting from carbon dioxide (CO 2) injection in deep saline reservoirs. The extracted brines usually have high concentrations of total dissolved solids (TDS) and various contaminants, and require proper disposal or treatment. In this article, first by conducting a critical review, we evaluate the applicability, limits, and advantages or challenges of various commercially available and emerging desalination technologies that can potentially be employed to treat the highly saline brine (with TDS values >70.000 ppm) and those that are applicable to a ~200,000 ppm TDS brine extracted frommore » the Mt. Simon Sandstone, a potential CO 2 storage site in Illinois, USA. Based on the side-by-side comparison of technologies, evaporators are selected as the most suitable existing technology for treating Mt. Simon brine. Process simulations are then conducted for a conceptual design for desalination of 454 m 3/h (2000 gpm) pretreated brine for near-zero liquid discharge by multi-effect evaporators. In conclusion, the thermal energy demand is estimated at 246kWh perm 3 of recoveredwater, ofwhich 212kWh/m 3 is required for multiple-effect evaporation and the remainder for salt drying. The process also requires additional electrical power of ~2 kWh/m 3.« less

Nanofiltration Results: Membrane Removal of Calcium, Magnesium, Sodium, Silica, Lithium, Chlorine, and Sulfate from Simulated Geothermal Brines

DOE Data Explorer

Jay Renew

2016-02-06

Results from a nanofiltration study utilizing simulated geothermal brines. The data includes a PDF documenting the process used to remove Calcium, Magnesium, Sodium, Silica, Lithium, Chlorine, and Sulfate from simulated geothermal brines. Three different membranes were evaluated. The results were analyzed using inductively coupled plasma mass spectrometry (ICP-MS).

Radiation Hardened Electronics Destined For Severe Nuclear Reactor Environments

DOE Office of Scientific and Technical Information (OSTI.GOV)

Holbert, Keith E.; Clark, Lawrence T.

Post nuclear accident conditions represent a harsh environment for electronics. The full station blackout experience at Fukushima shows the necessity for emergency sensing capabilities in a radiation-enhanced environment. This NEET (Nuclear Energy Enabling Technologies) research project developed radiation hardened by design (RHBD) electronics using commercially available technology that employs commercial off-the-shelf (COTS) devices and present generation circuit fabrication techniques to improve the total ionizing dose (TID) hardness of electronics. Such technology not only has applicability to severe accident conditions but also to facilities throughout the nuclear fuel cycle in which radiation tolerance is required. For example, with TID tolerance tomore » megarads of dose, electronics could be deployed for long-term monitoring, inspection and decontamination missions. The present work has taken a two-pronged approach, specifically, development of both board and application-specific integrated circuit (ASIC) level RHBD techniques. The former path has focused on TID testing of representative microcontroller ICs with embedded flash (eFlash) memory, as well as standalone flash devices that utilize the same fabrication technologies. The standalone flash devices are less complicated, allowing better understanding of the TID response of the crucial circuits. Our TID experiments utilize biased components that are in-situ tested, and in full operation during irradiation. A potential pitfall in the qualification of memory circuits is the lack of rigorous testing of the possible memory states. For this reason, we employ test patterns that include all ones, all zeros, a checkerboard of zeros and ones, an inverse checkerboard, and random data. With experimental evidence of improved radiation response for unbiased versus biased conditions, a demonstration-level board using the COTS devices was constructed. Through a combination of redundancy and power gating, the demonstration board exhibits radiation resilience to over 200 krad. Furthermore, our ASIC microprocessor using RHBD techniques was shown to be fully functional after an exposure of 2.5 Mrad whereas the COTS microcontroller units failed catastrophically at <100 krad. The methods developed in this work can facilitate the long-term viability of radiation-hard robotic systems, thereby avoiding obsolescence issues. As a case in point, the nuclear industry with its low purchasing power does not drive the semiconductor industry strategic plans, and the rapid advancements in electronics technology can leave legacy systems stranded.« less

Fermentation Cover Brine Reformulation for Cucumber Processing with Low Salt to Reduce Bloater Defect.

PubMed

Zhai, Y; Pérez-Díaz, I M

2017-12-01

Reformulation of calcium chloride (CaCl 2 ) cover brine for cucumber fermentation was explored as a mean to minimize the incidence of bloater defect. This study particularly focused on cover brine supplementation with calcium hydroxide (Ca[OH] 2 ), sodium chloride (NaCl), and acids to enhance buffer capacity, inhibit the indigenous carbon dioxide (CO 2 )- producing microbiota, and decrease the solubility of the gas. The influence of the cover brine formulations tested, on the cucumber fermentation microbiota, biochemistry, CO 2 production, and bloating defect was studied using metagenetics, HPLC analysis, a portable gas analyzer and bloater index, respectively. Cover brine supplementation with Ca(OH) 2 and acetic acid resulted in complete fermentations with final pH values 0.5 units higher than the un-supplemented control. Lactic acid production increased by approximately 22%, possibly inducing the observed reduction in the relative abundance of Enterobacteriaceae by 92%. Ca(OH) 2 supplementation also resulted in an increased relative abundance of Leuconostocaceae by 7%, which likely contributed to the observed increment in CO 2 levels by 25%. A 50% reduction on acetic acid formation was detected when cover brines were supplemented with Ca(OH) 2 and 690 mM (4%) NaCl. No significant difference was observed in bloater index as the result of Ca(OH) 2 or NaCl supplementation in cover brines, given that the CO 2 levels remained at above the 20 mg/100 mL needed to induce the defect. It is concluded that the modified cover brine formulation containing Ca(OH) 2 and NaCl enables the complete conversion of sugars, decreases production of CO 2 and levels of Enterobacteriaceae, but insignificantly reduces bloater index. A cucumber fermentation cover brine containing Ca(OH) 2 , 0.26% CaCl 2 , 345 mM (2%) NaCl, and acetic acid to pH 4.7 has a functional combination of ingredients enabling a complete conversion of sugars to lactic acid with reduced production of acetic acid and CO 2 . It represents a process ready cover brine formulation with the potential to allow the manufacture of cucumber pickles with low salt, enhanced food safety, and reduce environmental impact and water usage. Pilot commercial scale cucumber fermentations brined with such ingredients are to reveal the efficacy of this process ready formulation in the presence of oxygen from air in tanks, as opposed to 3.8 L (1-US gal) closed jars in the laboratory. © 2017 Institute of Food Technologists®.

Studying the impact of air/brine displacement on acoustic velocities in carbonates. El Amin Mokhtar and Sandra Vega

NASA Astrophysics Data System (ADS)

Mokhtar, E.; Vega, D.

2012-12-01

The impact of air/brine displacement on acoustic velocities of carbonate rocks is not fully comprehended yet. In order to improve our understanding of this effect, we conducted laboratory measurements of porosity and acoustic velocities (Vp and Vs) under both dry and brine saturated conditions at ambient pressure and temperature. The core plug samples in this study were collected from a hydrocarbon reservoir in the Middle East. A petrographic analysis was also performed on thin sections taken from the core plugs using a microscope and a digital camera. The aim of this analysis was to study depositional facies and the extent of diagenetic overprint that caused the observed variations in rock fabrics. Cross-plots were generated to analyze the trends of behavior between acoustic velocities and porosities taking into account the influence of different rock fabrics, in both dry and brine saturated samples. Acoustic velocities of brine saturated samples were higher than velocities of dry samples, as expected. However, their differences also respond to both, total porosity and carbonate rock fabrics. This result can be attributed to the different carbonate pore structures and rock frames formed during deposition and diagenesis. Similarly, the Vp/Vs ratio cross-plots display an increase in Vp/Vs ratios for the brine saturated samples compared to the dry ones. In conclusion, differences in acoustic velocities between dry and brine saturated carbonate rocks seem to be highly effected by porosity, rock fabric, and fluid content. This information can help to better understand the differences in acoustic response between gas and brine saturated zones in well logs and seismic.

Numerical studies of CO2 and brine leakage into a shallow aquifer through an open wellbore

NASA Astrophysics Data System (ADS)

Wang, Jingrui; Hu, Litang; Pan, Lehua; Zhang, Keni

2018-03-01

Industrial-scale geological storage of CO2 in saline aquifers may cause CO2 and brine leakage from abandoned wells into shallow fresh aquifers. This leakage problem involves the flow dynamics in both the wellbore and the storage reservoir. T2Well/ECO2N, a coupled wellbore-reservoir flow simulator, was used to analyze CO2 and brine leakage under different conditions with a hypothetical simulation model in water-CO2-brine systems. Parametric studies on CO2 and brine leakage, including the salinity, excess pore pressure (EPP) and initially dissolved CO2 mass fraction, are conducted to understand the mechanism of CO2 migration. The results show that brine leakage rates increase proportionally with EPP and inversely with the salinity when EPP varies from 0.5 to 1.5 MPa; however, there is no CO2 leakage into the shallow freshwater aquifer if EPP is less than 0.5 MPa. The dissolved CO2 mass fraction shows an important influence on the CO2 plume, as part of the dissolved CO2 becomes a free phase. Scenario simulation shows that the gas lifting effect will significantly increase the brine leakage rate into the shallow freshwater aquifer under the scenario of 3.89% dissolved CO2 mass fraction. The equivalent porous media (EPM) approach used to model the wellbore flow has been evaluated and results show that the EPM approach could either under- or over-estimate brine leakage rates under most scenarios. The discrepancies become more significant if a free CO2 phase evolves. Therefore, a model that can correctly describe the complex flow dynamics in the wellbore is necessary for investigating the leakage problems.

Brine delineation and monitoring with electrical resistivity tomography and electromagnetic borehole logging at the Fort Knox well field near West Point, Kentucky

USGS Publications Warehouse

Henderson, Rory; Unthank, Michael D.; Zettwoch, Douglas D.; Lane, John W.

2010-01-01

The potable water system at Fort Knox is threatened by brine contamination from improperly abandoned natural gas exploration wells. The Fort Knox well field is located near the town of West Point, Kentucky, in the flood plain of the Ohio River. At the site, unconsolidated sediments approximately 30 – 40 m thick, overlie shale and porous limestone. Brine is believed to flow vertically from the underlying formations to the unconsolidated aquifer through damaged or leaky well casings under a high hydraulic gradient from the artificially pressurized porous limestone, which is utilized for natural gas storage by a regional energy company. Upon reaching the unconsolidated aquifer, brinecontaminated groundwater enters water supply production wells under the pumping‐induced gradient. As part of the Fort Knox remediation strategy to reduce the impact of brine contamination, electrical resistivity tomography (ERT) and borehole electromagnetic (EM) logs are being collected annually to detect gross changes in subsurface conductivity. The 2009 ERT data show areas of high conductivity on the western (contaminated) side of the site with conductivities more than an order of magnitude higher than on the eastern (uncontaminated) side of the site. The areas of high conductivity are interpreted as brine contamination, consistent with known regions of brine contamination. Conductivities from the EM logs are consistent with the results from the ERT inversions. The EM logs show little change between 2008 and 2009, except for some small changes in the brine distribution in well PZ1. Yearly ERT surveys will be continued to detect new areas of brine contamination and monitor the remediation effort.

Modeling brine and nutrient dynamics in Antarctic sea ice: the case of dissolved silica

NASA Astrophysics Data System (ADS)

Vancoppenolle, M.; Goosse, H.; de Montety, A.; Fichefet, T.; Tremblay, B.; Tison, J.

2009-12-01

Sea ice ecosystems are characterized by micro-algae living in brine inclusions. The growth rate of ice algae depends on light and nutrient supply. Here, the interactions between nutrients and brine dynamics under the influence of algae are investigated using a one-dimensional model. The model includes snow and ice thermodynamics with brine physics and an idealized sea ice biological component, characterized by one nutrient, namely dissolved silica (DSi). In the model, DSi follows brine motion and is consumed by ice algae. Depending on physical ice characteristics, the brine flow is either advective, diffusive or turbulent. The vertical profiles of ice salinity and DSi concentration are solutions of advection-diffusion equations. The model is configured to simulate the typical thermodynamic regimes of first-year Antarctic pack ice. The simulated vertical profiles of salinity and DSi qualitatively reproduce observations. Analysis of results highlights the role of convection in the lowermost 5-10 cm of ice. Convection mixes saline, nutrient-poor brine with comparatively fresh, nutrient-rich seawater. This implies a rejection of salt to the ocean and a flux of DSi to the ice. In presence of growing algae, the simulated ocean-to-ice DSi flux increases by 0-115% compared to an abiotic situation. In turn, primary production and brine convection act in synergy to form a nutrient pump. The other important processes are the flooding of the surface by seawater and the percolation of meltwater. The former refills nutrients near the ice surface in spring. The latter, if present, tends to expell nutrients from the ice in summer. Sketch of salt (left) and nutrient (right) exchanges at the ice-ocean interface proposed in this paper.

Design Status of the Capillary Brine Residual in Containment Water Recovery System

NASA Technical Reports Server (NTRS)

Callahan, Michael R.; Sargusingh, Miriam

2016-01-01

One of the goals of the AES Life Support System (LSS) Project is to achieve 98% water loop closure for long duration human exploration missions beyond low Earth orbit. To meet this objective, the AES LSS Project is developing technologies to recover water from wastewater brine; highly concentrated waste products generated from a primary water recovery system. The state of the art system used aboard the International Space Station (ISS) has the potential to recover up to 85% water from unine wastewater, leaving a significant amounts of water in the waste brine, the recovery of which is a critical technology gap that must be filled in order to enable long duration human exploration. Recovering water from the urine wastewater brine is complicated by the concentration of solids as water is removed from the brine, and the concentration of the corrosive, toxic chemicals used to stabilize the urine which fouls and degrades water processing hardware, and poses a hazard to operators and crew. Brine Residual in Containment (BRIC) is focused on solids management through a process of "in-place" drying - the drying of brines within the container used for final disposal. Application of in-place drying has the potential to improve the safety and reliability of the system by reducing the exposure to crew and hardware to the problematic brine residual. Through a collaboration between the NASA Johnson Space Center and Portland Status University, a novel water recovery system was developed that utilizes containment geometry to support passive capillary flow and static phase separation allowing free surface evaporation to take place in a microgravity environment. A notional design for an ISS demonstration system was developed. This paper describes the concept for the system level design.

Design Status of the Capillary Brine Residual in Containment Water Recovery System

NASA Technical Reports Server (NTRS)

Sargusingh, Miriam J.; Callahan, Michael R.; Garison, John; Houng, Benjamin; Weislogel, Mark M.

2016-01-01

One of the goals of the AES Life Support System (LSS) Project is to achieve 98% water loop closure for long duration human exploration missions beyond low Earth orbit. To meet this objective, the AES LSS Project is developing technologies to recover water from wastewater brine; highly concentrated waste products generated from a primary water recovery system. The state of the art system used aboard the International Space Station (ISS) has the potential to recover up to 85% water from unine wastewater, leaving a significant amounts of water in the waste brine, the recovery of which is critical technology gap that must be filled in order to enable long duration human exploration. Recovering water from the urine wastewater brine is complicated by the concentration of solids as water is removed from the brine, and the concentration of the corrosive, toxic chemicals used to stabilize the urine which fouls and degrades water processing hardware, and poses a hazard to operators and crew. Brine Residual in Containment (BRIC) is focused on solids management through a process of "in-place" drying - the drying of brines within the container used for final disposal. Application of in-place drying has the potential to improve the safety and reliability of the system by reducing the exposure to curew and hardware to the problematic brine residual. Through a collaboration between the NASA Johnson Space Center and Portland Status University, a novel water recovery system was developed that utilizes containment geometry to support passive capillary flow and static phase separation allowing free surface evaporation to take place in a microgravity environment. A notional design for an ISS demonstration system was developed. This paper describes the testing performed to characterize the performance of the system as well as the status of the system level design.

Chemical aspects of a brine pool at the East Flower Garden bank, northwestern Gulf of Mexico

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brooks, J.M.; Bright, T.J.; Bernard, B.B.

1979-07-01

A small pool on the flank of the East Flower Garden bank at a depth of 72 m in the Gulf of Mexico contains anoxic, hypersaline (approx. 200 g.kg/sup -1/) water. The flux of brine into and out of the pool contributes to erosional processes on the bank. The bulk ionic composition of the brine is similar to that of the Orca Basin brine, but differences between the two in gaseous hydrocarbon and carbon isotope content indicate different modes of origin. High levels of bacterial activity in the brine are indicated by ATP (> 80 ng.liter/sup -1/), hydrogen sulfide (>more » 2000 ..mu..mol.liter/sup -1/), isotopically light ..sigma..CO/sub 2/ (delta/sup 13/C =-23/sup 0///sub 00/ and the apparent generaton of elemental sulfur.« less

A network model for characterizing brine channels in sea ice

NASA Astrophysics Data System (ADS)

Lieblappen, Ross M.; Kumar, Deip D.; Pauls, Scott D.; Obbard, Rachel W.

2018-03-01

The brine pore space in sea ice can form complex connected structures whose geometry is critical in the governance of important physical transport processes between the ocean, sea ice, and surface. Recent advances in three-dimensional imaging using X-ray micro-computed tomography have enabled the visualization and quantification of the brine network morphology and variability. Using imaging of first-year sea ice samples at in situ temperatures, we create a new mathematical network model to characterize the topology and connectivity of the brine channels. This model provides a statistical framework where we can characterize the pore networks via two parameters, depth and temperature, for use in dynamical sea ice models. Our approach advances the quantification of brine connectivity in sea ice, which can help investigations of bulk physical properties, such as fluid permeability, that are key in both global and regional sea ice models.

Development of the brine shrimp Artemia is accelerated during spaceflight

NASA Technical Reports Server (NTRS)

Spooner, B. S.; Metcalf, J.; DeBell, L.; Paulsen, A.; Noren, W.; Guikema, J. A.

1994-01-01

Developmentally arrested brine shrimp cysts have been reactivated during orbital spaceflight on two different Space Shuttle missions (STS-50 and STS-54), and their subsequent development has been compared with that of simultaneously reactivated ground controls. Flight and control brine shrimp do not significantly differ with respect to hatching rates or larval morphology at the scanning and transmission EM levels. A small percentage of the flight larvae had defective nauplier eye development, but the observation was not statistically significant. However, in three different experiments on two different flights, involving a total of 232 larvae that developed in space, a highly significant difference in degree of flight to control development was found. By as early as 2.25 days after reactivation of development, spaceflight brine shrimp were accelerated, by a full instar, over ground control brine shrimp. Although developing more rapidly, flight shrimp grew as long as control shrimp at each developmental instar or stage.

Uncertainty and sensitivity analysis for two-phase flow in the vicinity of the repository in the 1996 performance assessment for the Waste Isolation Pilot Plant: Undisturbed conditions

DOE Office of Scientific and Technical Information (OSTI.GOV)

HELTON,JON CRAIG; BEAN,J.E.; ECONOMY,K.

2000-05-19

Uncertainty and sensitivity analysis results obtained in the 1996 performance assessment for the Waste Isolation Pilot Plant are presented for two-phase flow the vicinity of the repository under undisturbed conditions. Techniques based on Latin hypercube sampling, examination of scatterplots, stepwise regression analysis, partial correlation analysis and rank transformation are used to investigate brine inflow, gas generation repository pressure, brine saturation and brine and gas outflow. Of the variables under study, repository pressure is potentially the most important due to its influence on spallings and direct brine releases, with the uncertainty in its value being dominated by the extent to whichmore » the microbial degradation of cellulose takes place, the rate at which the corrosion of steel takes place, and the amount of brine that drains from the surrounding disturbed rock zone into the repository.« less

Sodium Chloride Diffusion during Muscle Salting Evidenced by Energy-Dispersive X-ray Spectroscopy Imaging.

PubMed

Filgueras, Rénata; Peyrin, Frédéric; Vénien, Annie; Hénot, Jean Marc; Astruc, Thierry

2016-01-27

To better understand the relationship between the muscle structure and NaCl transfers in meat, we used energy-dispersive X-ray spectroscopy (EDS) coupled with scanning electron microscopy (SEM) to analyze brined and dry-salted rat muscles. The muscles were freeze-dried to avoid the delocalization of soluble ions that happens in regular dehydration through a graded series of ethanol. Na and Cl maps were superimposed on SEM images to combine the muscle structure and NaCl diffusion. Brining causes rapid diffusion of NaCl through the tissue. Most brine diffuses in a linear front from the muscle surface, but a small proportion enters through the perimysium network. The muscle area penetrated by brine shows heterogeneous patterns of NaCl retention, with some connective tissue islets containing more NaCl than other parts of perimysium. NaCl penetration is considerably slower after dry salting than after brining.

Countercurrent direct contact heat exchange process and system

DOEpatents

Wahl, III, Edward F.; Boucher, Frederic B.

1979-01-01

Recovery of energy from geothermal brines and other hot water sources by direct contact heat exchange with a working fluid, such as a hydrocarbon working fluid, e.g. isobutane. The process and system consists of a plurality of stages, each stage including mixing and settling units. In the first stage, hot brine and arm working fluid are intimately mixed and passed into a settler wherein the brine settles to the bottom of the settler and the hot working fluid rises to the top. The hot working fluid is passed to a heat engine or turbine to produce work and the working fluid is then recycled back into the system. The system is comprised of a series of stages each containing a settler and mixer, and wherein the working fluid and the brine flow in a countercurrent manner through the stages to recover the heat from the brine in increments and raise the temperature of the working fluid in increments.

Analysis of a Distributed Pulse Power System Using a Circuit Analysis Code

DTIC Science & Technology

1979-06-01

dose rate was then integrated to give a number that could be compared with measure- ments made using thermal luminescent dosimeters ( TLD ’ s). Since...NM 8 7117 AND THE BDM CORPORATION, ALBUQUERQUE, NM 87106 Abstract A sophisticated computer code (SCEPTRE), used to analyze electronic circuits...computer code (SCEPTRE), used to analyze electronic circuits, was used to evaluate the performance of a large flash X-ray machine. This device was

FIELD IMPLEMENTATION PLAN FOR A WILLISTON BASIN BRINE EXTRACTION AND STORAGE TEST

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hamling, John; Klapperich, Ryan; Stepan, Daniel

2016-03-31

The Energy & Environmental Research Center (EERC) successfully completed all technical work of Phase I, including development of a field implementation plan (FIP) for a brine extraction and storage test (BEST) in the North Dakota portion of the Williston Basin. This implementation plan was commissioned by the U.S. Department of Energy (DOE) National Energy Technology Laboratory (NETL) as a proxy for managing formation pressure plumes and measuring/monitoring the movement of differential pressure and CO2 plumes in the subsurface for future saline CO2 storage projects. BEST comprises the demonstration and validation of active reservoir management (ARM) strategies and extracted brine treatmentmore » technologies. Two prospective commercial brine injection sites were evaluated for BEST to satisfy DOE’s goals. Ultimately, an active saltwater disposal (SWD) site, Johnsons Corner, was selected because it possesses an ideal combination of key factors making it uniquely suited to host BEST. This site is located in western North Dakota and operated by Nuverra Environmental Solutions (Nuverra), a national leader in brine handling, treatment, and injection. An integrated management approach was used to incorporate local and regional geologic characterization activities with geologic and simulation models, inform a monitoring, verification, and accounting (MVA) plan, and to conduct a risk assessment. This approach was used to design a FIP for an ARM schema and an extracted brine treatment technology test bed facility. The FIP leverages an existing pressure plume generated by two commercial SWD wells. These wells, in conjunction with a new brine extraction well, will be used to conduct the ARM schema. Results of these tests will be quantified based on their impact on the performance of the existing SWD wells and the surrounding reservoir system. Extracted brine will be injected into an underlying deep saline formation through a new injection well. The locations of proposed extraction and injection wells were selected during the Phase I efforts. These wells will be permitted as North Dakota Administrative Code Underground Injection Control Class II wells and will yield additional characterization data which will further refine the FIP in Phase II. An array of surface and downhole monitoring techniques will validate ARM performance against predictive simulation results. Infrastructure will be constructed to manage extracted fluids at the surface and provide brine to a treatment test bed facility. Treatment of extracted brine can provide a means of reducing extracted brine disposal volumes, an alternate source of water, and/or salable products for beneficial use. A test bed facility will be constructed to provide a means of demonstrating these technologies on a wide range of brine concentrations. Screening criteria based on a techno-economic and life cycle assessment were developed to select high-salinity brine treatment technologies for extended duration treatment (30–60 days) in Phase II. A detailed cost assessment determined total implementation costs for BEST of $19,901,065 million (DOE share $15,680,505). These costs are inclusive of all necessary equipment, infrastructure construction, operations and project closeout costs required to implement BEST. An ideal combination of key factors makes the Johnsons Corner site uniquely suited to be the BEST demonstration.« less

Application Status of Rubidium, Cesium and Research Situation of its Separation from Brine with Solvent Extraction

NASA Astrophysics Data System (ADS)

Shi, Zhen; Du, Xuemin; Wang, Shiqiang; Guo, Yafei; Deng, Tianlong

2017-12-01

Rubidium, cesium and its compounds play an important role in traditional and high-tech fields. This paper focuses on the research status of separation rubidium and cesium in brine using solvent extraction, and briefly introduced the characteristics of this method, which can be used to realize industrial production of rubidium and cesium from brine.

Vegetation re-establishment on a hardwood forest site denuded by brine

Treesearch

R.S. Walters; L.R. Auchmoody

1989-01-01

Brine from active oil wells seeped through the soil of a forested site in north-western Pennsylvania and killed all vegetation in its path, leaving the affected area unproductive and unsightly. After the brine source was eliminated, herbaceous plants, shrubs and forest tree seedlings became established and developed rapidly. Establishment began in the first year and by...

Observation of a brine layer on an ice surface with an environmental scanning electron microscope at higher pressures and temperatures.

PubMed

Krausko, Ján; Runštuk, Jiří; Neděla, Vilém; Klán, Petr; Heger, Dominik

2014-05-20

Observation of a uranyl-salt brine layer on an ice surface using backscattered electron detection and ice surface morphology using secondary-electron detection under equilibrium conditions was facilitated using an environmental scanning electron microscope (ESEM) at temperatures above 250 K and pressures of hundreds of Pa. The micrographs of a brine layer over ice grains prepared by either slow or shock freezing provided a complementary picture of the contaminated ice grain boundaries. Fluorescence spectroscopy of the uranyl ions in the brine layer confirmed that the species exists predominately in the solvated state under experimental conditions of ESEM.

Formation and Persistence of Brine on Mars: Experimental Simulations throughout the Diurnal Cycle at the Phoenix Landing Site.

PubMed

Fischer, E; Martínez, G M; Rennó, N O

2016-12-01

In the last few years, water ice and salts capable of melting this ice and producing liquid saline water (brine) have been detected on Mars. Moreover, indirect evidence for brine has been found in multiple areas of the planet. Here, we simulate full diurnal cycles of temperature and atmospheric water vapor content at the Phoenix landing site for the first time and show experimentally that, in spite of the low Mars-like chamber temperature, brine forms minutes after the ground temperature exceeds the eutectic temperature of salts in contact with water ice. Moreover, we show that the brine stays liquid for most of the diurnal cycle when enough water ice is available to compensate for evaporation. This is predicted to occur seasonally in areas of the polar region where the temperature exceeds the eutectic value and frost or snow is deposited on saline soils, or where water ice and salts coexist in the shallow subsurface. This is important because the existence of liquid water is a key requirement for habitability. Key Words: Mars-Ice-Perchlorates-Brine-Water-Raman spectroscopy. Astrobiology 16, 937-948.

Measurement and modeling of CO₂ solubility in natural and synthetic formation brines for CO₂ sequestration.

PubMed

Zhao, Haining; Dilmore, Robert; Allen, Douglas E; Hedges, Sheila W; Soong, Yee; Lvov, Serguei N

2015-02-03

CO2 solubility data in the natural formation brine, synthetic formation brine, and synthetic NaCl+CaCl2 brine were collected at the pressures from 100 to 200 bar, temperatures from 323 to 423 K. Experimental results demonstrate that the CO2 solubility in the synthetic formation brines can be reliably represented by that in the synthetic NaCl+CaCl2 brines. We extended our previously developed model (PSUCO2) to calculate CO2 solubility in aqueous mixed-salt solution by using the additivity rule of the Setschenow coefficients of the individual ions (Na(+), Ca(2+), Mg(2+), K(+), Cl(-), and SO4(2-)). Comparisons with previously published models against the experimental data reveal a clear improvement of the proposed PSUCO2 model. Additionally, the path of the maximum gradient of the CO2 solubility contours divides the P-T diagram into two distinct regions: in Region I, the CO2 solubility in the aqueous phase decreases monotonically in response to increased temperature; in region II, the behavior of the CO2 solubility is the opposite of that in Region I as the temperature increases.

Variation of brine compositions resulting from flow from matrix or fracture permeability, investigated by high pressure laboratory experiments

NASA Astrophysics Data System (ADS)

Poszwa, A. C.; Coleman, M. L.; Pouya, A.; Ader, M.; Bounenni, A.

2003-04-01

Planning oil production from a chalk reservoir oilfield is difficult because the matrix usually has low permeability despite its high porosity. Most oil is thought to come from fracture porosity but the matrix contribution should increase as compaction occurs during production. To better understand the respective contributions from matrix and fracture, we studied the geochemical characteristics of fluids using high-pressure brine flow experiments on chalk cores. During the experiment axial load was changed relative to confining pressure to induce fractures and to close them again. We used chlorine stable isotope variations to study fluid pathway, because chlorine is a chemically conservative element in sedimentary systems and its isotopes fractionate only with physical processes like diffusion or adsorption that could occur mainly in the chalk matrix. A first experiment was performed on a very porous chalk from Henley (on-shore UK) and using a low-salinity brine. Large variations of brine Cl isotope composition were observed (from -0.56 to +0.08 per mil). The variations were correlated positively with the brine flux through the chalk and the permeability of the rock, both parameters controlled by the rock fracturing. A second experiment used brine with salinity similar to that of seawater. In this case, chemical and isotopic variations were not significant. From the beginning, the chalk structure seems to have been destroyed very quickly (induced fracture porosity collapsed) possibly because of the fluid nature, so that whatever pressure was applied, the permeability did not change significantly. Using Valhall reservoir chalk (offshore Norwegian North Sea) and fluid half the salinity of seawater in a third experiment, we obtained a large range of permeabilities. Brine isotopic trends were very similar on average to those of the first experiment even though variations were smaller (Cl isotopes from -0.09 to +0.29 per mil) and not significantly correlated simply to permeability values. The highest isotopic values were in brine flowed through chalk when the permeability was high and fractures opened; the lowest values were in brine flowed through the chalk when its permeability was reduced by closing fractures and increasing the relative contribution from matrix flow where diffusion processes fractionated chlorine isotopes. From this work it seems that the relative contributions from fracture and matrix permeability in reservoirs can be estimated from the geochemical compositions of brines that flowed from them.

Identification of transformation products during advanced oxidation of diatrizoate: Effect of water matrix and oxidation process.

PubMed

Azerrad, Sara P; Lütke Eversloh, Christian; Gilboa, Maayan; Schulz, Manoj; Ternes, Thomas; Dosoretz, Carlos G

2016-10-15

Removal of micropollutants from reverse osmosis (RO) brines of wastewater desalination by oxidation processes is influenced by the scavenging capacity of brines components, resulting in the accumulation of transformation products (TPs) rather than complete mineralization. In this work the iodinated contrast media diatrizoate (DTZ) was used as model compound due to its relative resistance to oxidation. Identification of TPs was performed in ultrapure water (UPW) and RO brines applying nonthermal plasma (NTP) and UVA-TiO2 as oxidation techniques. The influence of main RO brines components in the formation and accumulation of TPs, such as chloride, bicarbonate alkalinity and humic acid, was also studied during UVA-TiO2. DTZ oxidation pattern in UPW resulted similar in both UVA-TiO2 and NTP achieving 66 and 61% transformation, respectively. However, DTZ transformation in RO brines was markedly lower in UVA-TiO2 (9%) than in NTP (27%). These differences can be attributed to the synergic effect of RO brines components during NTP. Moreover, reactive species other than hydroxyl radical contributed to DTZ transformation, i.e., direct photolysis in UVA-TiO2 and direct photolysis + O3 in NTP accounted for 16 and 23%, respectively. DTZ transformation led to iodide formation in both oxidation techniques but it further oxidized to iodate by ozone in NTP. In total 14 transformation products were identified in UPW of which 3 were present only in UVA-TiO2 and 2 were present exclusively in NTP; 5 of the 14 TPs were absent in RO brines. Five of them were new and were denoted as TP-474A/B, TP-522, TP-586, TP-602, TP-628. TP-522 (mono-chlorinated) was elucidated only in presence of high chloride titer-synthetic water matrix in NTP, most probably formed by active chlorine species generated in situ. TPs accumulation in RO brines was markedly different in comparison to UPW. This denotes the influence of RO brines components in the formation of reactive species that could further attack DTZ/TPs and/or scavenging performed by these brine components that could limit further TPs degradation. Five plausible degradation pathways are proposed for DTZ transformation in UPW. Copyright © 2016 Elsevier Ltd. All rights reserved.

On the brine drainage and algal uptake controls of the nutrient supply to the sea ice interior

NASA Astrophysics Data System (ADS)

Vancoppenolle, M.; Goosse, H.; de Montety, A.; Fichefet, T.; Tison, J.-L.

2009-04-01

Sea ice ecosystems are important components of the biogeochemical cycles (including carbon) and hence have a potential impact on climate. They are characterized by large stocks of micro-algae. Those algae (mostly diatoms) live in liquid inclusions of saline brine, which are encased within the solid ice matrix and require sustained nutrient supply to grow. In this study, we investigate the interactions between nutrients, brine motion and algal growth, using a one-dimensional (1D) sea ice model. The model includes (i) a classical formulation for snow and ice thermodynamics with explicit, reformulated brine physics and (ii) an idealized sea ice biological component, characterized by one single nutrient, namely dissolved silica (DSi), which stocks are reduced by a prescribed primary production. DSi is considered as a passive tracer dissolved within brine following fluid motion. The brine flow regime (advective, diffusive or turbulent) is computed as a function of environmental ice conditions. In winter, a Rayleigh number proposed by Notz and Worster (2008) is used to differentiate diffusion and convection. Ice salinity and DSi concentrations within the ice are solutions of 1D advection-diffusion equations over the variable volume brine network domain. The model is configured for a typical year of seasonal Weddell Sea ice. The simulated vertical salinity and tracer profiles as well as ice-ocean salt fluxes realistically agree with observations. Complex bio-physical interactions are simulated by the model. Analysis highlights the role of convection in the lowermost 5-10 cm of ice (gravity drainage), mixing highly saline, nutrient-depleted brine with comparatively fresh, nutrient-rich seawater. Hence, gravity drainage rejects salt to the ocean and provides nutrients to the ice interior. In turn, primary production and brine convection act synergetically to form a nutrient pump, which enhances the net ocean-to-ice DSi flux by 20-115%, compared to an abiotic situation. The other important simulated processes are winter and spring surface flooding of seawater which supplies nutrients near the ice surface, and melt water percolation which - if present in reality - would tend to flush nutrients back to the ocean in summer. The physical background for sea ice tracers developed here is general and could be used to simulate other sea ice tracers (e.g., dissolved organic matter, isotopes, gases, radio-nuclides, ...), constituting an improved modelling strategy for sea ice brine and ecosystem dynamics.

PILOT TESTING: PRETREATMENT OPTIONS TO ALLOW RE-USE OF FRAC FLOWBACK AND PRODUCED BRINE FOR GAS SHALE RESOURCE DEVELOPMENT

DOE Office of Scientific and Technical Information (OSTI.GOV)

Burnett, David

2012-12-31

The goal of the A&M DOE NETL Project No. DE-FE0000847 was to develop a mobile, multifunctional water treatment capability designed specifically for “pre-treatment” of field waste brine. The project consisted of constructing s mobile “field laboratory” incorporating new technology for treating high salinity produced water and using the lab to conduct a side-by-side comparison between this new technology and that already existing in field operations. A series of four field trials were performed utilizing the mobile unit to demonstrate the effectiveness of different technology suitable for use with high salinity flow back brines and produced water. The design of themore » mobile unit was based on previous and current work at the Texas A&M Separation Sciences Pilot Plant. The several treatment techniques which have been found to be successful in both pilot plant and field tests had been tested to incorporate into a single multifunctional process train. Eight different components were evaluated during the trials, two types of oil and grease removal, one BTEX removal step, three micro-filters, and two different nanofilters. The performance of each technique was measured by its separation efficiency, power consumption, and ability to withstand fouling. The field trials were a success. Four different field brines were evaluated in the first trial in New York. Over 16,000 gallons of brine were processed. Using a power cost of $.10 per kWh, media pretreatment power use averaged $0.004 per barrel, solids removal $.04 per barrel and brine “softening” $.84 per barrel. Total power cost was approximately $1.00 per barrel of fluid treated. In Pennsylvania, brines collected from frac ponds were tested in two additional trials. Each of the brines was converted to an oil-free, solids-free brine with no biological activity. Brines were stable over time and would be good candidates for use as a make-up fluid in a subsequent fracturing fluid design. Reports on all of the field trials and subcontractor research have been summarized in this Final Report. Individual field trial reports and research reports are contained in the companion volume titled “Appendices”« less

Partition behavior of virgin olive oil phenolic compounds in oil-brine mixtures during thermal processing for fish canning.

PubMed

Sacchi, Raffaele; Paduano, Antonello; Fiore, Francesca; Della Medaglia, Dorotea; Ambrosino, Maria Luisa; Medina, Isabel

2002-05-08

The chemical modifications and partitioning toward the brine phase (5% salt) of major phenol compounds of extra virgin olive oil (EVOO) were studied in a model system formed by sealed cans filled with oil-brine mixtures (5:1, v/v) simulating canned-in-oil food systems. Filled cans were processed in an industrial plant using two sterilization conditions commonly used during fish canning. The partitioning of phenolic compounds toward brine induced by thermal processing was studied by reversed-phase high-performance liquid chromatographic analysis of the phenol fraction extracted from oils and brine. Hydroxytyrosol (1), tyrosol (2), and the complex phenolic compounds containing 1 and 2 (i.e., the dialdehydic form of decarboxymethyl oleuropein aglycon 3, the dialdehydic form of decarboxymethyl ligstroside aglycon 4, and the oleuropein aglycon 6) decreased in the oily phase after sterilization with a marked partitioning toward the brine phase. The increase of the total amount of 1 and 2 after processing, as well as the presence of elenolic acid 7 released in brine, revealed the hydrolysis of the ester bond of hydrolyzable phenolic compounds 3, 4, and 6 during thermal processing. Both phenomena (partitioning toward the water phase and hydrolysis) contribute to explain the loss of phenolic compounds exhibited by EVOO used as filling medium in canned foods, as well as the protection of n-3 polyunsaturated fatty acids in canned-in-EVOO fish products.

Microbial life at -13 °C in the brine of an ice-sealed Antarctic lake.

PubMed

Murray, Alison E; Kenig, Fabien; Fritsen, Christian H; McKay, Christopher P; Cawley, Kaelin M; Edwards, Ross; Kuhn, Emanuele; McKnight, Diane M; Ostrom, Nathaniel E; Peng, Vivian; Ponce, Adrian; Priscu, John C; Samarkin, Vladimir; Townsend, Ashley T; Wagh, Protima; Young, Seth A; Yung, Pung To; Doran, Peter T

2012-12-11

The permanent ice cover of Lake Vida (Antarctica) encapsulates an extreme cryogenic brine ecosystem (-13 °C; salinity, 200). This aphotic ecosystem is anoxic and consists of a slightly acidic (pH 6.2) sodium chloride-dominated brine. Expeditions in 2005 and 2010 were conducted to investigate the biogeochemistry of Lake Vida's brine system. A phylogenetically diverse and metabolically active Bacteria dominated microbial assemblage was observed in the brine. These bacteria live under very high levels of reduced metals, ammonia, molecular hydrogen (H(2)), and dissolved organic carbon, as well as high concentrations of oxidized species of nitrogen (i.e., supersaturated nitrous oxide and ∼1 mmol⋅L(-1) nitrate) and sulfur (as sulfate). The existence of this system, with active biota, and a suite of reduced as well as oxidized compounds, is unusual given the millennial scale of its isolation from external sources of energy. The geochemistry of the brine suggests that abiotic brine-rock reactions may occur in this system and that the rich sources of dissolved electron acceptors prevent sulfate reduction and methanogenesis from being energetically favorable. The discovery of this ecosystem and the in situ biotic and abiotic processes occurring at low temperature provides a tractable system to study habitability of isolated terrestrial cryoenvironments (e.g., permafrost cryopegs and subglacial ecosystems), and is a potential analog for habitats on other icy worlds where water-rock reactions may cooccur with saline deposits and subsurface oceans.

Rubidium extraction from seawater brine by an integrated membrane distillation-selective sorption system.

PubMed

Naidu, Gayathri; Jeong, Sanghyun; Johir, Md Abu Hasan; Fane, Anthony G; Kandasamy, Jaya; Vigneswaran, Saravanamuthu

2017-10-15

The ultimate goal of seawater reverse osmosis (SWRO) brine management is to achieve minimal liquid discharge while recovering valuable resources. The suitability of an integrated system of membrane distillation (MD) with sorption for the recovery of rubidium (Rb + ) and simultaneous SWRO brine volume reduction has been evaluated for the first time. Polymer encapsulated potassium copper hexacyanoferrate (KCuFC(PAN)) sorbent exhibited a good selectivity for Rb + sorption with 10-15% increment at 55 °C (Langmuir Q max  = 125.11 ± 0.20 mg/g) compared to at 25 °C (Langmuir Q max  = 108.71 ± 0.20 mg/g). The integrated MD-KCuFC(PAN) system with periodic membrane cleaning, enabled concentration of SWRO brine to a volume concentration factor (VCF) of 2.9 (65% water recovery). A stable MD permeate flux was achieved with good quality permeate (conductivity of 15-20 μS/cm). Repeated cycles of MD-KCuFC(PAN) sorption with SWRO brine enabled the extraction of 2.26 mg Rb + from 12 L of brine (equivalent to 1.9 kg of Rb/day, or 0.7 tonne/yr from a plant producing 10,000 m 3 /day brine). KCuFC(PAN) showed a high regeneration and reuse capacity. NH 4 Cl air stripping followed by resorcinol formaldehyde (RF) resin filtration enabled to recover Rb + from the desorbed solution. Copyright © 2017 Elsevier Ltd. All rights reserved.

Surface Complexation Modeling of Calcite Zeta Potential Measurement in Mixed Brines for Carbonate Wettability Characterization

NASA Astrophysics Data System (ADS)

Song, J.; Zeng, Y.; Biswal, S. L.; Hirasaki, G. J.

2017-12-01

We presents zeta potential measurements and surface complexation modeling (SCM) of synthetic calcite in various conditions. The systematic zeta potential measurement and the proposed SCM provide insight into the role of four potential determining cations (Mg2+, SO42- , Ca2+ and CO32-) and CO2 partial pressure in calcite surface charge formation and facilitate the revealing of calcite wettability alteration induced by brines with designed ionic composition ("smart water"). Brines with varying potential determining ions (PDI) concentration in two different CO2 partial pressure (PCO2) are investigated in experiments. Then, a double layer SCM is developed to model the zeta potential measurements. Moreover, we propose a definition for contribution of charged surface species and quantitatively analyze the variation of charged species contribution when changing brine composition. After showing our model can accurately predict calcite zeta potential in brines containing mixed PDIs, we apply it to predict zeta potential in ultra-low and pressurized CO2 environments for potential applications in carbonate enhanced oil recovery including miscible CO2 flooding and CO2 sequestration in carbonate reservoirs. Model prediction reveals that pure calcite surface will be positively charged in all investigated brines in pressurized CO2 environment (>1atm). Moreover, the sensitivity of calcite zeta potential to CO2 partial pressure in the various brine is found to be in the sequence of Na2CO3 > Na2SO4 > NaCl > MgCl2 > CaCl2 (Ionic strength=0.1M).

Microbial life at −13 °C in the brine of an ice-sealed Antarctic lake

PubMed Central

Murray, Alison E.; Kenig, Fabien; Fritsen, Christian H.; McKay, Christopher P.; Cawley, Kaelin M.; Edwards, Ross; Kuhn, Emanuele; McKnight, Diane M.; Ostrom, Nathaniel E.; Peng, Vivian; Ponce, Adrian; Priscu, John C.; Samarkin, Vladimir; Townsend, Ashley T.; Wagh, Protima; Young, Seth A.; Yung, Pung To; Doran, Peter T.

2012-01-01

The permanent ice cover of Lake Vida (Antarctica) encapsulates an extreme cryogenic brine ecosystem (−13 °C; salinity, 200). This aphotic ecosystem is anoxic and consists of a slightly acidic (pH 6.2) sodium chloride-dominated brine. Expeditions in 2005 and 2010 were conducted to investigate the biogeochemistry of Lake Vida’s brine system. A phylogenetically diverse and metabolically active Bacteria dominated microbial assemblage was observed in the brine. These bacteria live under very high levels of reduced metals, ammonia, molecular hydrogen (H2), and dissolved organic carbon, as well as high concentrations of oxidized species of nitrogen (i.e., supersaturated nitrous oxide and ∼1 mmol⋅L−1 nitrate) and sulfur (as sulfate). The existence of this system, with active biota, and a suite of reduced as well as oxidized compounds, is unusual given the millennial scale of its isolation from external sources of energy. The geochemistry of the brine suggests that abiotic brine-rock reactions may occur in this system and that the rich sources of dissolved electron acceptors prevent sulfate reduction and methanogenesis from being energetically favorable. The discovery of this ecosystem and the in situ biotic and abiotic processes occurring at low temperature provides a tractable system to study habitability of isolated terrestrial cryoenvironments (e.g., permafrost cryopegs and subglacial ecosystems), and is a potential analog for habitats on other icy worlds where water-rock reactions may cooccur with saline deposits and subsurface oceans. PMID:23185006

Hydrogeologic aspects of brine disposal in the East Poplar oil field, Fort Peck Indian Reservation, northeastern Montana

DOE Office of Scientific and Technical Information (OSTI.GOV)

Craigg, S.D.; Thamke, J.N.

1993-04-01

The East Poplar Oil Field encompasses about 70 square miles in the south-central part of the Fort Peck Indian Reservation. Oil production began in 1952 from the Mississippian Madison Group. Production depths range from about 5,500 to 6,000 feet below land surface. Large quantities of brine (water having a dissolved-solids concentration greater than 35,000 milligrams per liter) have been produced with the oil. The brine has a dissolved-solids concentration of as much as 160,000 milligrams per liter. Most of the brine has been disposed of by injection into shallower subsurface formations (mainly the Lower Cretaceous Dakota Sandstone at depths ofmore » about 3,300 feet and the Upper Cretaceous Judith River Formation at depths of about 1,000 feet). Smaller quantities of brine have been directed to storage and evaporation pits. Handling, transport, and disposal of the brine have resulted in its movement into and migration through shallow Quaternary alluvial and glacial deposits along the Poplar River valley. Locally, domestic water supplies are obtained from these deposits. The major point, sources of shallow ground-water contamination probably is leakage of brine from corroded disposal-well casing and pipelines. Using electromagnetic geophysical techniques and auger drilling, three saline-water plumes in alluvial deposits and one plum in glacial deposits have been delineated. Dominant constituents in plume areas are sodium and chloride, whereas those in nonplume areas are sodium and bicarbonate.« less

Measuring hot flash phenomenonology using ambulatory prospective digital diaries

PubMed Central

Fisher, William I.; Thurston, Rebecca C.

2016-01-01

Objective This study provides the description, protocol, and results from a novel prospective ambulatory digital hot flash phenomenon diary. Methods This study included 152 midlife women with daily hot flashes who completed an ambulatory electronic hot flash diary continuously for the waking hours of 3 consecutive days. In this diary, women recorded their hot flashes and accompanying characteristics and associations as the hot flashes occurred. Results Self-reported hot flash severity on the digital diaries indicated that the majority of hot flashes were rated as mild (41.3%) or moderate (43.7%). Severe (13.1%) and very severe (1.8%) hot flashes were less common. Hot flash bother ratings were rated as mild (43%), or moderate (33.5%), with fewer hot flashes reported bothersome (17.5%) or very bothersome (6%). The majority of hot flashes were reported as occurring on the on the face (78.9%), neck (74.7%), and chest (61.3%). Prickly skin was reported concurrently with 32% of hot flashes, 7% with anxiety and 5% with nausea. A novel finding, 38% of hot flashes were accompanied by a premonitory aura. Conclusion A prospective electronic digital hot flash diary allows for a more precise quantitation of hot flashes while overcoming many of the limitations of commonly employed retrospective questionnaires and paper diaries. Unique insights into the phenomenology, loci and associated characteristics of hot flashes were obtained using this device. The digital hot flash phenomenology diary is recommended for future ambulatory studies of hot flashes as a prospective measure of the hot flash experience. PMID:27404030

Measuring hot flash phenomenonology using ambulatory prospective digital diaries.

PubMed

Fisher, William I; Thurston, Rebecca C

2016-11-01

This study provides the description, protocol, and results from a novel prospective ambulatory digital hot flash phenomenon diary. This study included 152 midlife women with daily hot flashes who completed an ambulatory electronic hot flash diary continuously for the waking hours of three consecutive days. In this diary, women recorded their hot flashes and accompanying characteristics and associations as the hot flashes occurred. Self-reported hot flash severity on the digital diaries indicated that the majority of hot flashes were rated as mild (41.3%) or moderate (43.7%). Severe (13.1%) and very severe (1.8%) hot flashes were less common. Hot flash bother ratings were rated as mild (43%), or moderate (33.5%), with fewer hot flashes reported bothersome (17.5%) or very bothersome (6%). The majority of hot flashes were reported as occurring on the face (78.9%), neck (74.7%), and chest (61.3%). Of all reported hot flashes, 32% occurred concurrently with prickly skin, 7% with anxiety, and 5% with nausea. A novel finding from the study was that 38% of hot flashes were accompanied by a premonitory aura. A prospective electronic digital hot flash diary allows for a more precise quantitation of hot flashes while overcoming many of the limitations of commonly used retrospective questionnaires and paper diaries. Unique insights into the phenomenology, loci, and associated characteristics of hot flashes were obtained using this device. The digital hot flash phenomenology diary is recommended for future ambulatory studies of hot flashes as a prospective measure of the hot flash experience.

Bitopertin in Negative Symptoms of Schizophrenia-Results From the Phase III FlashLyte and DayLyte Studies.

PubMed

Bugarski-Kirola, Dragana; Blaettler, Thomas; Arango, Celso; Fleischhacker, Wolfgang W; Garibaldi, George; Wang, Alice; Dixon, Mark; Bressan, Rodrigo A; Nasrallah, Henry; Lawrie, Stephen; Napieralski, Julie; Ochi-Lohmann, Tania; Reid, Carol; Marder, Stephen R

2017-07-01

There is currently no standard of care for treatment of negative symptoms of schizophrenia, although some previous results with glutamatergic agonists have been promising. Three (SunLyte [WN25308], DayLyte [WN25309], and FlashLyte [NN25310]) phase III, multicenter, randomized, 24-week, double-blind, parallel-group, placebo-controlled studies evaluated the efficacy and safety of adjunctive bitopertin in stable patients with persistent predominant negative symptoms of schizophrenia treated with antipsychotics. SunLyte met the prespecified criteria for lack of efficacy and was declared futile. Key inclusion criteria were age ≥18 years, DSM-IV-TR diagnosis of schizophrenia, score ≥40 on the sum of the 14 Positive and Negative Syndrome Scale negative symptoms and disorganized thought factors, unaltered antipsychotic treatment, and clinical stability. Following a 4-week prospective stabilization period, patients were randomly assigned 1:1:1 to bitopertin (5 mg and 10 mg [DayLyte] and 10 mg and 20 mg [FlashLyte]) or placebo once daily for 24 weeks. The primary efficacy end point was mean change from baseline in Positive and Negative Syndrome Scale negative symptom factor score at week 24. The intent-to-treat population in DayLyte and FlashLyte included 605 and 594 patients, respectively. At week 24, mean change from baseline showed improvement in all treatment arms but no statistically significant separation from placebo in Positive and Negative Syndrome Scale negative symptom factor score and all other end points. Bitopertin was well tolerated. These studies provide no evidence for superior efficacy of adjunctive bitopertin in any of the doses tested over placebo in patients with persistent predominant negative symptoms of schizophrenia. Copyright © 2017. Published by Elsevier Inc.

Microbiology of solar salt ponds

NASA Technical Reports Server (NTRS)

Javor, B.

1985-01-01

Solar salt ponds are shallow ponds of brines that range in salinity from that of normal seawater (3.4 percent) through NaCl saturation. Some salterns evaporate brines to the potash stage of concentration (bitterns). All the brines (except the bitterns, which are devoid of life) harbor high concentrations of microorganisms. The high concentrations of microorganisms and their adaptation to life in the salt pond are discussed.

Assessing Radium Activity in Shale Gas Produced Brine

NASA Astrophysics Data System (ADS)

Fan, W.; Hayes, K. F.; Ellis, B. R.

2015-12-01

The high volumes and salinity associated with shale gas produced water can make finding suitable storage or disposal options a challenge, especially when deep well brine disposal or recycling for additional well completions is not an option. In such cases, recovery of commodity salts from the high total dissolved solids (TDS) of the brine wastewater may be desirable, yet the elevated concentrations of the naturally occurring radionuclides such as Ra-226 and Ra-228 in produced waters (sometimes substantially greater than the EPA limit of 5 pCi/L) may concentrate during these steps and limit salt recovery options. Therefore, assessing the potential presence of these Ra radionuclides in produced water from shale gas reservoir properties is desirable. In this study, we seek to link U and Th content within a given shale reservoir to the expected Ra content of produced brine by accounting for secular equilibrium within the rock and subsequent release to Ra to native brines. Produced brine from a series of Antrim shale wells and flowback from a single Utica-Collingwood shale well in Michigan were sampled and analyzed via ICP-MS to measure Ra content. Gamma spectroscopy was used to verify the robustness of this new Ra analytical method. Ra concentrations were observed to be up to an order of magnitude higher in the Antrim flowback water samples compared to those collected from the Utica-Collingwood well. The higher Ra content in Antrim produced brines correlates well with higher U content in the Antrim (19 ppm) relative to the Utica-Collingwood (3.5 ppm). We also observed an increase in Ra activity with increasing TDS in the Antrim samples. This Ra-TDS relationship demonstrates the influence of competing divalent cations in controlling Ra mobility in these clay-rich reservoirs. In addition, we will present a survey of geochemical data from other shale gas plays in the U.S. correlating shale U, Th content with produced brine Ra content. A goal of this study is to develop a method to predict the expected Ra activity in shale gas produced brines on a regional or play-specific basis in an effort to guide wastewater management practices or optimize regional treatment strategies.

Fate and groundwater impacts of produced water releases at OSPER "B" site, Osage County, Oklahoma

USGS Publications Warehouse

Kharaka, Y.K.; Kakouros, E.; Thordsen, J.J.; Ambats, G.; Abbott, M.M.

2007-01-01

For the last 5 a, the authors have been investigating the transport, fate, natural attenuation and ecosystem impacts of inorganic and organic compounds in releases of produced water and associated hydrocarbons at the Osage-Skiatook Petroleum Environmental Research (OSPER) "A" and "B" sites, located in NE Oklahoma. Approximately 1.0 ha of land at OSPER "B", located within the active Branstetter lease, is visibly affected by salt scarring, tree kills, soil salinization, and brine and petroleum contamination. Site "B" includes an active production tank battery and adjacent large brine pit, two injection well sites, one with an adjacent small pit, and an abandoned brine pit and tank battery site. Oil production in this lease started in 1938, and currently there are 10 wells that produce 0.2-0.5 m3/d (1-3 bbl/d) oil, and 8-16 m3/d (50-100 bbl/d) brine. Geochemical data from nearby oil wells show that the produced water source is a Na-Ca-Cl brine (???150,000 mg/L TDS), with high Mg, but low SO4 and dissolved organic concentrations. Groundwater impacts are being investigated by detailed chemical analyses of water from repeated sampling of 41 boreholes, 1-71 m deep. The most important results at OSPER "B" are: (1) significant amounts of produced water from the two active brine pits percolate into the surficial rocks and flow towards the adjacent Skiatook reservoir, but only minor amounts of liquid petroleum leave the brine pits; (2) produced-water brine and minor dissolved organics have penetrated the thick (3-7 m) shale and siltstone units resulting in the formation of three interconnected plumes of high-salinity water (5000-30,000 mg/L TDS) that extend towards the Skiatook reservoir from the two active and one abandoned brine pits; and (3) groundwater from the deep section of only one well, BR-01 located 330 m upslope and west of the site, appear not to be impacted by petroleum operations. ?? 2007.

Efflorescence of Magnesium Perchlorate by Contact with Mineral Dust Particles

NASA Astrophysics Data System (ADS)

Ushijima, S.; Tolbert, M. A.; Gough, R. V.

2017-12-01

Liquid water was not uncommon on early Mars and it shaped geologic features on the surface that are still seen today. Due to the extremely cold and dry conditions of Mars currently, only water ice and water vapor have been observed and or detected. However, it has been suggested that liquid may form seasonally based on the observations of recurring slope lineae (RSL). The liquid may be a brine composed of hygroscopic salts such as perchlorates whose hydrated form has recently been detected in an RSL by the Mars Reconnaissance Orbiter. Through a process called deliquescence, the salts can absorb water from the surrounding environment and become a brine above a specific relative humidity (RH) known as the deliquescence relative humidity (DRH). The reverse process, recrystallization or efflorescence, often occurs at a much lower RH called the efflorescence relative humidity (ERH). The hysteresis effect caused by the distinctly different RH values allows for liquid brines to be metastable even under dry conditions. However, there is evidence that ERH can be raised when a mineral particle encounters the surface of the brine or it is immersed inside, effectively diminishing the metastability potential of liquid brines. If the brines are responsible for RSL formation, the brine will inevitably mix with the Martian soil. Thus, it is important to understand the effects that mineral particles can have on efflorescence. Here we use optical trapping to examine efflorescence of magnesium perchlorate in the presence of montmorillonite and halite. Studies on the efflorescence and deliquescence of magnesium perchlorate has shown that its brine could be stable in the subsurface of Mars during certain periods of time. Both montmorillonite and halite have been suggested to be a part of or similar to components of the Martian soil. Results at ambient conditions have shown that efflorescence of magnesium perchlorate is unaffected by the presence of either minerals. Whether the droplet of magnesium perchlorate was pure or exposed to halite or montmorillonite the ERH was near 13% RH at room temperature. Although not under Mars conditions, the results suggest that the stability of magnesium perchlorate brine could be unaffected by the surrounding mineral and could still possibly contribute to RSL formation.

Patient- and cohort-specific dose and risk estimation for abdominopelvic CT: a study based on 100 patients

NASA Astrophysics Data System (ADS)

Tian, Xiaoyu; Li, Xiang; Segars, W. Paul; Frush, Donald P.; Samei, Ehsan

2012-03-01

The purpose of this work was twofold: (a) to estimate patient- and cohort-specific radiation dose and cancer risk index for abdominopelvic computer tomography (CT) scans; (b) to evaluate the effects of patient anatomical characteristics (size, age, and gender) and CT scanner model on dose and risk conversion coefficients. The study included 100 patient models (42 pediatric models, 58 adult models) and multi-detector array CT scanners from two commercial manufacturers (LightSpeed VCT, GE Healthcare; SOMATOM Definition Flash, Siemens Healthcare). A previously-validated Monte Carlo program was used to simulate organ dose for each patient model and each scanner, from which DLP-normalized-effective dose (k factor) and DLP-normalized-risk index values (q factor) were derived. The k factor showed exponential decrease with increasing patient size. For a given gender, q factor showed exponential decrease with both increasing patient size and patient age. The discrepancies in k and q factors across scanners were on average 8% and 15%, respectively. This study demonstrates the feasibility of estimating patient-specific organ dose and cohort-specific effective dose and risk index in abdominopelvic CT requiring only the knowledge of patient size, gender, and age.

Viscous liquid film flow on dune slopes of Mars

NASA Astrophysics Data System (ADS)

Möhlmann, Diedrich; Kereszturi, Akos

2010-06-01

It is shown that viscous liquid film flow (VLF-flow) on the surfaces of slopes of martian dunes can be a low-temperature rheological phenomenon active today on high latitudes. A quantitative model indicates that the VLF-flows are consistent with the flow of liquid brines similar to that observed by imaging at the Phoenix landing site. VLF-flows depend on the viscosity, dynamics, and energetics of temporary darkened liquid brines. The darkening of the flowing brine is possibly, at least partially, attributed to non-volatile ingredients of the liquid brines. Evidence of previous VLF-flows can also be seen on the dunes, suggesting that it is an ongoing process that also occurred in the recent past.

Contaminant Permeation in the Ionomer-Membrane Water Processor (IWP) System

NASA Technical Reports Server (NTRS)

Kelsey, Laura K.; Finger, Barry W.; Pasadilla, Patrick; Perry, Jay

2016-01-01

The Ionomer-membrane Water Processor (IWP) is a patented membrane-distillation based urine brine water recovery system. The unique properties of the IWP membrane pair limit contaminant permeation from the brine to the recovered water and purge gas. A paper study was conducted to predict volatile trace contaminant permeation in the IWP system. Testing of a large-scale IWP Engineering Development Unit (EDU) with urine brine pretreated with the International Space Station (ISS) pretreatment formulation was then conducted to collect air and water samples for quality analysis. Distillate water quality and purge air GC-MS results are presented and compared to predictions, along with implications for the IWP brine processing system.

Brine flow in heated geologic salt.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kuhlman, Kristopher L.; Malama, Bwalya

This report is a summary of the physical processes, primary governing equations, solution approaches, and historic testing related to brine migration in geologic salt. Although most information presented in this report is not new, we synthesize a large amount of material scattered across dozens of laboratory reports, journal papers, conference proceedings, and textbooks. We present a mathematical description of the governing brine flow mechanisms in geologic salt. We outline the general coupled thermal, multi-phase hydrologic, and mechanical processes. We derive these processes governing equations, which can be used to predict brine flow. These equations are valid under a wide varietymore » of conditions applicable to radioactive waste disposal in rooms and boreholes excavated into geologic salt.« less

Silica in alkaline brines

USGS Publications Warehouse

Jones, B.F.; Rettig, S.L.; Eugster, H.P.

1967-01-01

Analysis of sodium carbonate-bicarbonate brines from closed basins in volcanic terranes of Oregon and Kenya reveals silica contents of up to 2700 parts per million at pH's higher than 10. These high concentrations of SiO 2 can be attributed to reaction of waters with silicates, and subsequent evaporative concentration accompanied by a rise in pH. Supersaturation with respect to amorphous silica may occur and persist for brines that are out of contact with silicate muds and undersaturated with respect to trona; correlation of SiO2 with concentration of Na and total CO2 support this interpretation. Addition of moredilute waters to alkaline brines may lower the pH and cause inorganic precipitation of substantial amounts of silica.

Projected effects of proposed chloride-control projects on shallow ground water; preliminary results for the Wichita River basin, Texas

USGS Publications Warehouse

Garza, Sergio

1983-01-01

Two-dimensional mathematical computer models were developed for aquifer simulation of: (1) Steady-state conditions in a fresh-water system and (2) transient conditions in a brine- fresh-water system where the density effects of the brine are considered. The main results 'of projecting the effects of the proposed Truscott Brine Lake on the fresh-water aquifer are: (1) Hydraulic head rises of 5 to 40 feet would be confined to areas near the proposed dam and along the lake shoreline, and (2) migration of salt water downstream from the dam generally would be limited to less than 1 mile and apparently would not reach equilibrium during the 100-year duration of the project. The modeling efforts did not include possible effects related to hydrodynamic dispersion in the brine- fresh-water system. Possible changes in the hydraulic conductivity of the aquifer, due to physical and chemical interactions in the brine and fresh-water environments, also were not considered.

Offshore oceanographic and environmental monitoring services for the Strategic Petroleum Reserve. Annual report for the Bryan Mound site, September 1982-August 1983. Volume III. Executive summary

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hann, R.W. Jr.; Giammona, C.P.; Randall, R.E.

1984-03-01

This report describes the findings for the 12 months of postdisposal study conducted from September 1982 through August 1983. The areas of investigation are benthos, brine plume, data management, nekton, physical oceanography, and water and sediment quality. The specific objectives of this report are: (1) to describe the physical oceanographic and meteorological conditions which have been measured at the offshore diffuser site and in the surrounding waters; (2) to describe the effect of brine discharge on the benthic community in the diffuser site area; (3) to discuss the effect of the brine discharge on the quality of the water andmore » sediment in the vicinity of the diffuser site; (4) to describe the measurement and empirical prediction of the areal and vertical extent of the brine plume; and (5) to characterize the effect of brine discharge on the nekton community in the vicinity of the diffuser. 2 figures.« less

Effects of high salinity from desalination brine on growth, photosynthesis, water relations and osmolyte concentrations of seagrass Posidonia australis.

PubMed

Cambridge, M L; Zavala-Perez, A; Cawthray, G R; Mondon, J; Kendrick, G A

2017-02-15

Highly saline brines from desalination plants expose seagrass communities to salt stress. We examined effects of raised salinity (46 and 54psu) compared with seawater controls (37psu) over 6weeks on the seagrass, Posidonia australis, growing in tanks with the aim of separating effects of salinity from other potentially deleterious components of brine and determining appropriate bioindicators. Plants survived exposures of 2-4weeks at 54psu, the maximum salinity of brine released from a nearby desalination plant. Salinity significantly reduced maximum quantum yield of PSII (chlorophyll a fluorescence emissions). Leaf water potential (Ψ w ) and osmotic potential (Ψ π ) were more negative at increased salinity, while turgor pressure (Ψ p ) was unaffected. Leaf concentrations of K + and Ca 2+ decreased, whereas concentrations of sugars (mainly sucrose) and amino acids increased. We recommend leaf osmolarity, ion, sugar and amino acid concentrations as bioindicators for salinity effects, associated with brine released in desalination plant outfalls. Copyright © 2016 Elsevier Ltd. All rights reserved.

Profiling of Indigenous Microbial Community Dynamics and Metabolic Activity During Enrichment in Molasses-Supplemented Crude Oil-Brine Mixtures for Improved Understanding of Microbial Enhanced Oil Recovery.

PubMed

Halim, Amalia Yunita; Pedersen, Dorthe Skou; Nielsen, Sidsel Marie; Lantz, Anna Eliasson

2015-06-01

Anaerobic incubations using crude oil and brine from a North Sea reservoir were conducted to gain increased understanding of indigenous microbial community development, metabolite production, and the effects on the oil-brine system after addition of a complex carbon source, molasses, with or without nitrate to boost microbial growth. Growth of the indigenous microbes was stimulated by addition of molasses. Pyrosequencing showed that specifically Anaerobaculum, Petrotoga, and Methanothermococcus were enriched. Addition of nitrate favored the growth of Petrotoga over Anaerobaculum. The microbial growth caused changes in the crude oil-brine system: formation of oil emulsions, and reduction of interfacial tension (IFT). Reduction in IFT was associated with microbes being present at the oil-brine interphase. These findings suggest that stimulation of indigenous microbial growth by addition of molasses has potential as microbial enhanced oil recovery (MEOR) strategy in North Sea oil reservoirs.

Daily Physical Activity and Hot Flashes in the Study of Women's Health Across the Nation FLASHES Study

PubMed Central

Gibson, Carolyn; Matthews, Karen; Thurston, Rebecca

2014-01-01

Objective To examine the role of physical activity in menopausal hot flashes. Competing models conceptualize physical activity as a risk or protective factor for hot flashes. Few studies have examined this relationship prospectively using physiologic measures of hot flashes and physical activity. Design Over two 48 hour-periods, 51 participants wore a physiologic hot flash monitor and activity monitor, and reported their hot flashes in an electronic diary. Physiologic hot flashes, reported hot flashes and reported hot flashes without physiological corroboration were related to activity changes using hierarchical generalized linear modeling, adjusting for potential confounders. Setting Community. Patients Midlife women. Interventions None. Main Outcome Measures Physiologically-detected hot flashes and reported hot flashes with and without physiologic corroboration. Results Hot flash reports without physiologic corroboration were more likely after activity increases (OR 1.04, 95% CI: 1.00-1.10, p=.01), particularly among women with higher levels of depressive symptoms (interaction p=.02). No other types of hot flashes were related to physical activity. Conclusion Acute increases in physical activity were associated with increased reporting of hot flashes lacking physiologic corroboration, particularly among women with depressive symptoms. Clinicians should consider the role of symptom perception and reporting in relations between physical activity and hot flashes. PMID:24491454

Adaptive P300 based control system

PubMed Central

Jin, Jing; Allison, Brendan Z.; Sellers, Eric W.; Brunner, Clemens; Horki, Petar; Wang, Xingyu; Neuper, Christa

2015-01-01

An adaptive P300 brain-computer interface (BCI) using a 12 × 7 matrix explored new paradigms to improve bit rate and accuracy. During online use, the system adaptively selects the number of flashes to average. Five different flash patterns were tested. The 19-flash paradigm represents the typical row/column presentation (i.e., 12 columns and 7 rows). The 9- and 14-flash A & B paradigms present all items of the 12 × 7 matrix three times using either nine or 14 flashes (instead of 19), decreasing the amount of time to present stimuli. Compared to 9-flash A, 9-flash B decreased the likelihood that neighboring items would flash when the target was not flashing, thereby reducing interference from items adjacent to targets. 14-flash A also reduced adjacent item interference and 14-flash B additionally eliminated successive (double) flashes of the same item. Results showed that accuracy and bit rate of the adaptive system were higher than the non-adaptive system. In addition, 9- and 14-flash B produced significantly higher performance than their respective A conditions. The results also show the trend that the 14-flash B paradigm was better than the 19-flash pattern for naïve users. PMID:21474877

Recovery of Lithium from Geothermal Brine with Lithium–Aluminum Layered Double Hydroxide Chloride Sorbents

DOE Office of Scientific and Technical Information (OSTI.GOV)

Paranthaman, Mariappan Parans; Li, Ling; Luo, Jiaqi

In this paper, we report a three-stage bench-scale column extraction process to selectively extract lithium chloride from geothermal brine. The goal of this research is to develop materials and processing technologies to improve the economics of lithium extraction and production from naturally occurring geothermal and other brines for energy storage applications. A novel sorbent, lithium aluminum layered double hydroxide chloride (LDH), is synthesized and characterized with X-ray powder diffraction, scanning electron microscopy, inductively coupled plasma optical emission spectrometry (ICP-OES), and thermogravimetric analysis. Each cycle of the column extraction process consists of three steps: (1) loading the sorbent with lithium chloridemore » from brine; (2) intermediate washing to remove unwanted ions; (3) final washing for unloading the lithium chloride ions. Our experimental analysis of eluate vs feed concentrations of Li and competing ions demonstrates that our optimized sorbents can achieve a recovery efficiency of ~91% and possess excellent Li apparent selectivity of 47.8 compared to Na ions and 212 compared to K ions, respectively in the brine. Finally, the present work demonstrates that LDH is an effective sorbent for selective extraction of lithium from brines, thus offering the possibility of effective application of lithium salts in lithium-ion batteries leading to a fundamental shift in the lithium supply chain.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kaplan, Ruth; Mamrosh, Darryl; Salih, Hafiz H.

Brine extraction is a promising strategy for the management of increased reservoir pressure, resulting from carbon dioxide (CO 2) injection in deep saline reservoirs. The extracted brines usually have high concentrations of total dissolved solids (TDS) and various contaminants, and require proper disposal or treatment. In this article, first by conducting a critical review, we evaluate the applicability, limits, and advantages or challenges of various commercially available and emerging desalination technologies that can potentially be employed to treat the highly saline brine (with TDS values >70.000 ppm) and those that are applicable to a ~200,000 ppm TDS brine extracted frommore » the Mt. Simon Sandstone, a potential CO 2 storage site in Illinois, USA. Based on the side-by-side comparison of technologies, evaporators are selected as the most suitable existing technology for treating Mt. Simon brine. Process simulations are then conducted for a conceptual design for desalination of 454 m 3/h (2000 gpm) pretreated brine for near-zero liquid discharge by multi-effect evaporators. In conclusion, the thermal energy demand is estimated at 246kWh perm 3 of recoveredwater, ofwhich 212kWh/m 3 is required for multiple-effect evaporation and the remainder for salt drying. The process also requires additional electrical power of ~2 kWh/m 3.« less

Recovery of Lithium from Geothermal Brine with Lithium-Aluminum Layered Double Hydroxide Chloride Sorbents.

PubMed

Paranthaman, Mariappan Parans; Li, Ling; Luo, Jiaqi; Hoke, Thomas; Ucar, Huseyin; Moyer, Bruce A; Harrison, Stephen

2017-11-21

We report a three-stage bench-scale column extraction process to selectively extract lithium chloride from geothermal brine. The goal of this research is to develop materials and processing technologies to improve the economics of lithium extraction and production from naturally occurring geothermal and other brines for energy storage applications. A novel sorbent, lithium aluminum layered double hydroxide chloride (LDH), is synthesized and characterized with X-ray powder diffraction, scanning electron microscopy, inductively coupled plasma optical emission spectrometry (ICP-OES), and thermogravimetric analysis. Each cycle of the column extraction process consists of three steps: (1) loading the sorbent with lithium chloride from brine; (2) intermediate washing to remove unwanted ions; (3) final washing for unloading the lithium chloride ions. Our experimental analysis of eluate vs feed concentrations of Li and competing ions demonstrates that our optimized sorbents can achieve a recovery efficiency of ∼91% and possess excellent Li apparent selectivity of 47.8 compared to Na ions and 212 compared to K ions, respectively in the brine. The present work demonstrates that LDH is an effective sorbent for selective extraction of lithium from brines, thus offering the possibility of effective application of lithium salts in lithium-ion batteries leading to a fundamental shift in the lithium supply chain.

Rock-fluid chemical interactions at reservoir conditions: The influence of brine chemistry and extent of reaction

NASA Astrophysics Data System (ADS)

Anabaraonye, B. U.; Crawshaw, J.; Trusler, J. P. M.

2016-12-01

Following carbon dioxide injection in deep saline aquifers, CO2 dissolves in the formation brines forming acidic solutions that can subsequently react with host reservoir minerals, altering both porosity and permeability. The direction and rates of these reactions are influenced by several factors including properties that are associated with the brine system. Consequently, understanding and quantifying the impacts of the chemical and physical properties of the reacting fluids on overall reaction kinetics is fundamental to predicting the fate of the injected CO2. In this work, we present a comprehensive experimental study of the kinetics of carbonate-mineral dissolution in different brine systems including sodium chloride, sodium sulphate and sodium bicarbonate of varying ionic strengths. The impacts of the brine chemistry on rock-fluid chemical reactions at different extent of reactions are also investigated. Using a rotating disk technique, we have investigated the chemical interactions between the CO2-saturated brines and carbonate minerals at conditions of pressure (up to 10 MPa) and temperature (up to 373 K) pertinent to carbon storage. The changes in surface textures due to dissolution reaction were studied by means of optical microscopy and vertical scanning interferometry. Experimental results are compared to previously derived models.

Reconnaissance evaluation of contamination in the alluvial aquifer in the East Poplar oil field, Roosevelt County, Montana

USGS Publications Warehouse

Levings, G.W.

1984-01-01

Water moving from north to south in the alluvial aquifer of the Poplar River valley becomes contaminated with sodium chloride in the area underlain by the East Poplar oil fields. Four types of ground water were identified in the study area. Type 1 is sodium bicarbonate water. Type 2 is sodium chloride water with varying quantities of calcium and magnesium. Type 3 water contains sodium and chloride in significantly larger concentrations than Type 2. Type 4 water is the brine being injected into brine-disposal wells. Contamination of the alluvial aquifer is indicated by a brine-freshwater interface in the alluvium, by downstream increase in chloride concentration of the Poplar River, and by downstream change in water type of the Poplar River. Contamination also may be indicated by the distribution of iron and manganese concentrations in water from wells near a brine-disposal well. Possible sources of sodium chloride contamination in the alluvium are brine-disposal wells, pipelines, and storage or evaporation pits. The contamination can occur from leaks in the casing of disposal wells or in pipelines caused by the corrosive nature of the brine or from storage or evaporation pits that have been improperly sealed or have sustained tears in the sealing material. (USGS)

Recovery of Lithium from Geothermal Brine with Lithium–Aluminum Layered Double Hydroxide Chloride Sorbents

DOE PAGES

Paranthaman, Mariappan Parans; Li, Ling; Luo, Jiaqi; ...

2017-10-27

In this paper, we report a three-stage bench-scale column extraction process to selectively extract lithium chloride from geothermal brine. The goal of this research is to develop materials and processing technologies to improve the economics of lithium extraction and production from naturally occurring geothermal and other brines for energy storage applications. A novel sorbent, lithium aluminum layered double hydroxide chloride (LDH), is synthesized and characterized with X-ray powder diffraction, scanning electron microscopy, inductively coupled plasma optical emission spectrometry (ICP-OES), and thermogravimetric analysis. Each cycle of the column extraction process consists of three steps: (1) loading the sorbent with lithium chloridemore » from brine; (2) intermediate washing to remove unwanted ions; (3) final washing for unloading the lithium chloride ions. Our experimental analysis of eluate vs feed concentrations of Li and competing ions demonstrates that our optimized sorbents can achieve a recovery efficiency of ~91% and possess excellent Li apparent selectivity of 47.8 compared to Na ions and 212 compared to K ions, respectively in the brine. Finally, the present work demonstrates that LDH is an effective sorbent for selective extraction of lithium from brines, thus offering the possibility of effective application of lithium salts in lithium-ion batteries leading to a fundamental shift in the lithium supply chain.« less

Chemical and isotopic constrains on the origin of brine and saline groundwater in Hetao plain, Inner Mongolia.

PubMed

Liu, Jun; Chen, Zongyu; Wang, Lijuan; Zhang, Yilong; Li, Zhenghong; Xu, Jiaming; Peng, Yurong

2016-08-01

The origin and evolution of brine and saline groundwater have always been a challenged work for geochemists and hydrogeologists. Chemical and isotopic data of brine and saline waters were used to trace the sources of salinity and therefore to understand the transport mechanisms of groundwater in Xishanzui, Inner Mongolia. Both Cl/Br (molar) versus Na/Br (molar) and Cl (meq/L) versus Na (meq/L) indicated that salinity was from halite dissolution or at least a significant impact by halite dissolution. The logarithmic plot of the concentration trends of Cl (mg/L) versus Br (mg/L) for the evaporation of seawater and the Qinghai Salt Lake showed that the terrestrial halite dissolution was the dominated contribution for the salinity of this brine. The stable isotope ratios of hydrogen and oxygen suggested that the origin of brine was from paleorecharge water which experienced mixing of modern water in shallow aquifer. δ(37)Cl values ranged from -0.02 to 3.43 ‰ (SMOC), and reflecting mixing of different sources. The Cl isotopic compositions suggest that the dissolution of halite by paleometeoric water had a great contribution to the salinity of brine, and the contributions of the residual seawater and the dissolution of halite by the Yellow River water could be excluded.

Changes in migration mode of brine and supercritical CO2 in imbibition process under steady flow state of very slow fluid velocities

NASA Astrophysics Data System (ADS)

Kogure, Tetsuya; Zhang, Yi; Nishizawa, Osamu; Xue, Ziqiu

2018-05-01

Relative permeability curves and flow mechanisms of CO2 and brine in Berea sandstone were investigated during a two-phase flow imbibition process, where CO2 saturation in the rock decreased from 55 per cent to 9 per cent by stepwise decrease of CO2/brine injection ratios. Total fluid flow velocity was 4.25 × 10-6 m/s, corresponding to the capillary number of order ˜10-8 for CO2 flow. The relative permeability curves showed a slight hysteresis compared to those during the drainage process. Local CO2 saturation and the differential pressure showed temporal fluctuations when the average differential pressure showed constant values or very small trends. The fluctuations in local CO2 saturation correlate with local porosity distributions. The differential pressure between the inlet and outlet ends showed the largest fluctuation when the CO2/brine ratio equals to one. A final brine-only injection resulted in more CO2 trapped within low porosity zones. These results suggest important roles of ganglion dynamics in the low flow rate ranges, where fluid pathways undergo repetitive brine snap-off and coalescence of CO2 ganglia that causes morphological changes in distributions of CO2 pathways.

Impact of pressure and temperature on CO2-brine-mica contact angles and CO2-brine interfacial tension: Implications for carbon geo-sequestration.

PubMed

Arif, Muhammad; Al-Yaseri, Ahmed Z; Barifcani, Ahmed; Lebedev, Maxim; Iglauer, Stefan

2016-01-15

Precise characterization of wettability of CO2-brine-rock system and CO2-brine interfacial tension at reservoir conditions is essential as they influence capillary sealing efficiency of caprocks, which in turn, impacts the structural and residual trapping during CO2 geo-sequestration. In this context, we have experimentally measured advancing and receding contact angles for brine-CO2-mica system (surface roughness ∼12nm) at different pressures (0.1MPa, 5MPa, 7MPa, 10MPa, 15MPa, 20MPa), temperatures (308K, 323K, and 343K), and salinities (0wt%, 5wt%, 10wt%, 20wt% and 30wt% NaCl). For the same experimental matrix, CO2-brine interfacial tensions have also been measured using the pendant drop technique. The results indicate that both advancing and receding contact angles increase with pressure and salinity, but decrease with temperature. On the contrary, CO2-brine interfacial tension decrease with pressure and increase with temperature. At 20MPa and 308K, the advancing angle is measured to be ∼110°, indicating CO2-wetting. The results have been compared with various published literature data and probable factors responsible for deviations have been highlighted. Finally we demonstrate the implications of measured data by evaluating CO2 storage heights under various operating conditions. We conclude that for a given storage depth, reservoirs with lower pressures and high temperatures can store larger volumes and thus exhibit better sealing efficiency. Copyright © 2015 Elsevier Inc. All rights reserved.

Stability of the Orca Basin Brine Interface Determined Using Radium Isotopes

NASA Astrophysics Data System (ADS)

Peterson, R. N.; Peterson, L.; Montoya, J. P.; Joye, S. B.

2016-02-01

The Orca Basin is an intraslope basin in the northern continental slope of the Gulf of Mexico, and contains a deep (up to 220 m) anoxic, hypersaline brine lake. The brine interface extends from ocean salinity (at a water depth of 2125 m) to a constant salinity of 215 psu below a depth of 2250 m. This interface is considered to be among the most stable interfaces on the planet, and contains distinct zones of macrofaunal and microbial assemblages. The brine lake is supported by continued dissolution of exposed rock salt at an estimated rate of 0.5 million t/yr. Such dissolution of salt should serve as a source of radium isotopes, and given their range of half-lives, these isotopes can serve as unique proxies to the location and rate of salt dissolution into this basin. We have collected a series of radon and radium isotope profiles through this brine lake over the past 4 years, which allow us to assess the spatial and temporal stability of this interface. Throughout the brine lake, we observe strong enrichments in unsupported Ra-224, Rn-222, and Ra-226 in a 10 m thick zone near the base of the brine interface, between 2232 m and 2242 m. The strong enrichment in unsupported Ra-224 in this layer must be supported by a continuous source, presumably the dissolution of exposed salt rock. Various degrees of isotopic enrichment throughout the lake provide an assessment of the rates of lateral and vertical dispersion of salt and associated chemical constituents.

Understanding the role of brine ionic composition on oil recovery by assessment of wettability from colloidal forces.

PubMed

Alshakhs, Mohammed J; Kovscek, Anthony R

2016-07-01

The impact of injection brine salinity and ionic composition on oil recovery has been an active area of research for the past 25years. Evidence from laboratory studies and field tests suggests that implementing certain modifications to the ionic composition of the injection brine leads to greater oil recovery. The role of salinity modification is attributed to its ability to shift wettability of a rock surface toward water wetness. The amount of trapped oil released depends on the nature of rock, oil, and brine surface interactions. Reservoir rocks exhibit different affinities to fluids. Carbonates show stronger adsorption of oil films as opposed to the strongly water-wet and mixed-wet sandstones. The concentration of divalent ions and total salinity of the injection brine are other important factors to consider. Accordingly, this paper provides a review of laboratory and field studies of the role of brine composition on oil recovery from carbonaceous rock as well as rationalization of results using DLVO (Derjaguin, Landau, Verwey and Overbeek) theory of surface forces. DLVO evaluates the contribution of each component of the oil/brine/rock system to the wettability. Measuring zeta potential of each pair of surfaces by a charged particle suspension method is used to estimate double layer forces, disjoining pressure, and contact-angle. We demonstrate the applicability of the DLVO approach by showing a comprehensive experimental study that investigates the effect of divalent ions in carbonates, and uses disjoining pressure results to rationalize observations from core flooding and direct contact-angle measurements. Copyright © 2015 Elsevier B.V. All rights reserved.

Thermal-gradient migration of brine inclusions in salt crystals. [Synthetic single crystals of NaCl and KCl

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yagnik, S.K.

1982-09-01

It has been proposed that high-level nuclear waste be disposed in a geologic repository. Natural-salt deposits, which are being considered for this purpose, contain a small volume fraction of water in the form of brine inclusions distributed throughout the salt. Radioactive-decay heating of the nuclear wastes will impose a temperature gradient on the surrounding salt which mobilizes the brine inclusions. Inclusions filled completely with brine migrate up the temperature gradient and eventually accumulate brine near the buried waste forms. The brine may slowly corrode or degrade the waste forms which is undesirable. In this work, thermal gradient migration of bothmore » all-liquid and gas-liquid inclusions was experimentally studied in synthetic single crystals of NaCl and KCl using a hot-stage attachment to an optical microscope which was capable of imposing temperature gradients and axial compressive loads on the crystals. The migration velocities of the inclusions were found to be dependent on temperature, temperature gradient, and inclusion shape and size. The velocities were also dictated by the interfacial mass transfer resistance at brine/solid interface. This interfacial resistance depends on the dislocation density in the crystal, which in turn, depends on the axial compressive loading of the crystal. At low axial loads, the dependence between the velocity and temperature gradient is non-linear.At high axial loads, however, the interfacial resistance is reduced and the migration velocity depends linearly on the temperature gradient. All-liquid inclusions filled with mixed brines were also studied. For gas-liquid inclusions, three different gas phases (helium, air and argon) were compared. Migration studies were also conducted on single crystallites of natural salt as well as in polycrystalline natural salt samples. The behavior of the inclusions at large angle grain boundaries was observed. 35 figures, 3 tables.« less

Metamorphosed Plio-Pleistocene evaporites and the origins of hypersaline brines in the Salton Sea geothermal system, California: Fluid inclusion evidence

NASA Astrophysics Data System (ADS)

McKibben, Michael A.; Williams, Alan E.; Okubo, Susumu

1988-05-01

The Salton Sea geothermal system (SSGS) occurs in Plio-Pleistocene deltaic-lacustrine-evaporite sediments deposited in the Salton Trough, an active continental rift zone. Temperatures up to 365°C and hypersaline brines with up to 26 wt.% TDS are encountered at 1-3 km depth in the sediments, which are undergoing active greenschist facies hydrothermal metamorphism. Previous models for the origins of the Na-Ca-K-Cl brines have assumed that the high salinities were derived mainly from the downward percolation of cold, dense brines formed by low-temperature dissolution of shallow non-marine evaporites. New drillcores from the central part of the geothermal field contain metamorphosed, bedded evaporites at 1 km depth consisting largely of hornfelsic anhydrite interbedded with anhydrite-cemented solution-collapse shale breccias. Fluid inclusions trapped within the bedded and breccia-cementing anhydrite homogenize at 300°C (identical to the measured downhole temperature) and contain saline Na-Ca-K-Cl brines. Some of the inclusions contain up to 50 vol.% halite, sylvite and carbonate crystals at room temperature, and some halite crystals persist to above 300°C upon laboratory heating. The data are consistent with the trapping of halite-saturated Na-Ca-K-Cl fluids during hydrothermal metamorphism of the evaporites and accompanying solution collapse of interbedded shales. We conclude that many of the salt crystals in inclusions are the residuum of bedded evaporitic salt that was dissolved during metamorphism by heated connate fluids. Therefore, the high salinities of the Salton Sea geothermal brines are derived in part from the in situ hydrothermal metamorphism and dissolution of halides and CaSO 4 from relatively deeply-buried lacustrine evaporites. This fact places important constraints on modeling fluid-flow in the SSGS, as brines need not have migrated over great distances. The brines have been further modified to their present complex Na-Ca-K-Fe-Mn-Cl compositions by on-going sediment metamorphism and water-rock interaction.

Bacillus sp. LT3 improves the survival of gnotobiotic brine shrimp (Artemia franciscana) larvae challenged with Vibrio campbellii by enhancing the innate immune response and by decreasing the activity of shrimp-associated vibrios.

PubMed

Niu, Yufeng; Defoirdt, Tom; Baruah, Kartik; Van de Wiele, Tom; Dong, Shuanglin; Bossier, Peter

2014-10-10

Bacteria belonging to the genus Bacillus are amongst the most intensively studied group of bacteria for use as probiotics in aquaculture. However, the exact mechanism of action of these bacteria is often not well described, and the microbiota that are naturally present in cultures of test organisms often compromise the interpretation of the results. The present study aimed to evaluate the putative probiotic effect of Bacillus sp. LT3 in a model system with gnotobiotic brine shrimp Artemia franciscana larvae. The strain significantly increased the survival of brine shrimp larvae challenged with Vibrio campbellii when administered 6h before the challenge. Under these conditions, LT3 was able to colonize the brine shrimp gastrointestinal tract and to decrease the in vivo pathogen activity as indicated by the bioluminescence of the V. campbellii associated with brine shrimp larvae. In order to investigate the effect of the Bacillus strain on the innate immune system of the brine shrimp larvae, prophenoloxidase and transglutaminase mRNA levels were monitored, while heat shock protein 70 mRNA levels were measured as an indicator of physiological stress. Interestingly, 12h after challenge, the prophenoloxidase mRNA level in the larvae pre-treated with LT3 and challenged with V. campbellii was approximately 8-fold higher than in the other treatments. Further, a decreased mRNA level of transglutaminase gene and heat shock protein 70 gene suggested that pretreatment with LT3 results in less stress and tissue damage in the brine shrimp larvae upon V. campbellii challenge. These results indicated that Bacillus sp. LT3 could improve the survival of brine shrimp larvae when challenged with pathogenic V. campbellii, both by decreasing the in vivo activity of the pathogen and by priming the innate immune response through activating the prophenoloxidase system. Copyright © 2014 Elsevier B.V. All rights reserved.

Life in the Slow, Dark, Salty, Cold and Oxygen-Depleted Lane - Insights on Habitability from Lake Vida

NASA Astrophysics Data System (ADS)

Murray, A.

2014-04-01

Ice-entrained Lake Vida brine has provided an accessible natural habitat to study life in the slow lane - where cellular growth is limited, but not extinguished. We measured in situ stable isotopic signatures of N2O, SO42-, H2, conducted experiments utilizing stable isotope geochemical tracers to detect microbial transformations and employed radioisotopically-labeled amino acid precursors to detect cellular macromolecule biosynthesis. The results indicated a dominance of abiotic processes in the brine - yet support metabolically active life through detection of nominal rates of protein biosynthesis. At the same time, the brine has posed a challenge to our understanding of ecosystem energetics. Data collected thus far suggests that the brine is isolated from surfical processes and receives no new mass or energy from above. Calculations have estimated carbon remineralization rates, which indicate that resources should be depleted to the level of small molecules perhaps supporting a methanogenic ecosystem given the amount of time since encapsulation at the temperatures recorded - yet the brine is resource-rich harboring abundant bacteria and large molecules, in addition to a complex mixture of both reduced and oxidized compounds. This has motivated explorations into alternative sources of energy such as hydrogen - which was detected at levels 10 micromolar - that could be generated by brine-rock interactions and supply endogenous energy to this closed ecosystem. This cold, salty, anoxic and organically rich brine, provides insight into a new category of habitable earth ecosystems that may also give us food for thought when considering habitability of giant planet icy worlds or of icy exoplanets. However, the methods we use, and the framework of scientific inquiry applied, are limited by perception and familiarity of rates of change that are important in human time scales. The Vida-icy brine ecosystem provides a model for expansion of our understanding of habitability in which time scales need to be extended, and the role of intermingling abiotic and biotic processes need to be considered.

Improving Understanding of the Chemical Mechanism of Oil Recovery from Oil-Wet Carbonate Reservoirs: AN Experimental Approach

NASA Astrophysics Data System (ADS)

Purswani, P.; Karpyn, Z.

2017-12-01

Chemical tuning of injecting brine has found great success in improving oil recovery from oil-wet rocks. In particular, the importance of Mg2+, Ca2+, and SO42- ions has been identified as critical for incremental oil recovery via multi-ion exchange mechanism of wettability alteration. To improve understanding of this underlying mechanism and, to evaluate the individual contribution of these ions towards improving oil recovery, a series of waterflood experiments with varying ion composition were performed at 90 oC. Characterization techniques like zeta potential (ZP), contact angle measurements and trace element analysis were performed to evaluate the surface interactions taking place among the rock samples, brine solution, and the crude oil. ZP measurements highlight the affinity of Mg2+, Ca2+, and SO42- ions towards the rock surface in chemically tuned brines (CTBs), where, an increase in the magnitude of ZP was seen with an increase in the concentration of each of these ions. Oil recovery measurements showed an increase in oil recovery for all the CTBs compared to seawater. Relative permeability estimations and contact angle measurements showed corresponding trends of increasing water-wetness. Maximum recovery of 75.47% original oil in place (OOIP) was observed for the brine with increased Mg2+ ion concentration due to higher activity of Mg2+ ions. Lower recovery of 63.58% OOIP was seen for the brine with increased Ca2+ ion concentration due to lower activity of Ca2+ ions, and further lower recovery of 58.59% OOIP was seen for the brine with increased SO42- ion concentration due to the possible precipitation of these ions on the rock surface. These surface reactions were confirmed through the ionic analysis of the effluent brine during each waterflooding experiment. These results help understand the importance of chemical tuning of brines towards improving oil recovery and provides experimental insight into the chemical reactions that occur during this process.

Kinetics of ikaite precipitation and dissolution in seawater-derived brines at sub-zero temperatures to 265 K

NASA Astrophysics Data System (ADS)

Papadimitriou, Stathys; Kennedy, Hilary; Kennedy, Paul; Thomas, David N.

2014-09-01

The kinetics of calcium carbonate hexahydrate (ikaite) precipitation and dissolution were investigated in seawater and seawater-derived brines at sub-zero temperatures using the constant addition experimental technique. The steady state rate of these two processes was found to be a function of the deviation of the solution from equilibrium with respect to ikaite and conformed to the same empirical rate law as the anhydrous CaCO3 polymorphs, calcite and aragonite. In addition to the saturation state of the brine with respect to ikaite, the salinity of the brine and the temperature of the reaction evidently exerted some control on the ikaite precipitation kinetics, while the dissolution kinetics of the polymorph were not noticeably influenced by these two parameters. The experimental salinity and temperature conditions were equivalent to those at thermal equilibrium between brine and ice in the sea ice cover of polar seas. Simple modelling of the CO2 system by extrapolation of the oceanic equivalent to sea ice brines showed that the physical concentration of seawater ions and the changes in ikaite solubility as a function of salinity and temperature, both inherent in the sea ice system, would be insufficient to drive the emergent brines to ikaite supersaturation and precipitation in sea ice down to -8 °C. The loss of dissolved inorganic carbon to the gas phase of sea ice and to sympagic autotrophs are two independent mechanisms which, in nature, could prompt the brine CO2 system towards ikaite supersaturation and precipitation. Under these conditions, the steady state precipitation rate of ikaite was found to be fast enough for rapid formation within short time scales (days to weeks) in sea ice. The observed ikaite dissolution kinetics were also found conducive to short turn-over time scales of a few hours to a few days in corrosive solutions, such as surface seawater.

Oil/water/rock wettability: Influencing factors and implications for low salinity water flooding in carbonate reservoirs

DOE PAGES

Chen, Yongqiang; Xie, Quan; Sari, Ahmad; ...

2017-11-21

Wettability of the oil/brine/rock system is an essential petro-physical parameter which governs subsurface multiphase flow behaviour and the distribution of fluids, thus directly affecting oil recovery. Recent studies [1–3] show that manipulation of injected brine composition can enhance oil recovery by shifting wettability from oil-wet to water-wet. However, what factor(s) control system wettability has not been completely elucidated due to incomplete understanding of the geochemical system. To isolate and identify the key factors at play we used in this paper SO 4 2—free solutions to examine the effect of salinity (formation brine/FB, 10 times diluted formation brine/10 dFB, and 100more » times diluted formation brine/100 dFB) on the contact angle of oil droplets at the surface of calcite. We then compared contact angle results with predictions of surface complexation by low salinity water using PHREEQC software. We demonstrate that the conventional dilution approach likely triggers an oil-wet system at low pH, which may explain why the low salinity water EOR-effect is not always observed by injecting low salinity water in carbonated reservoirs. pH plays a fundamental role in the surface chemistry of oil/brine interfaces, and wettability. Our contact angle results show that formation brine triggered a strong water-wet system (35°) at pH 2.55, yet 100 times diluted formation brine led to a strongly oil-wet system (contact angle = 175°) at pH 5.68. Surface complexation modelling correctly predicted the wettability trend with salinity; the bond product sum ([>CaOH 2 +][–COO -] + [>CO 3 -][–NH +] + [>CO 3 -][–COOCa +]) increased with decreasing salinity. Finally, at pH < 6 dilution likely makes the calcite surface oil-wet, particularly for crude oils with high base number. Yet, dilution probably causes water wetness at pH > 7 for crude oils with high acid number.« less

Oil/water/rock wettability: Influencing factors and implications for low salinity water flooding in carbonate reservoirs

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chen, Yongqiang; Xie, Quan; Sari, Ahmad

Wettability of the oil/brine/rock system is an essential petro-physical parameter which governs subsurface multiphase flow behaviour and the distribution of fluids, thus directly affecting oil recovery. Recent studies [1–3] show that manipulation of injected brine composition can enhance oil recovery by shifting wettability from oil-wet to water-wet. However, what factor(s) control system wettability has not been completely elucidated due to incomplete understanding of the geochemical system. To isolate and identify the key factors at play we used in this paper SO 4 2—free solutions to examine the effect of salinity (formation brine/FB, 10 times diluted formation brine/10 dFB, and 100more » times diluted formation brine/100 dFB) on the contact angle of oil droplets at the surface of calcite. We then compared contact angle results with predictions of surface complexation by low salinity water using PHREEQC software. We demonstrate that the conventional dilution approach likely triggers an oil-wet system at low pH, which may explain why the low salinity water EOR-effect is not always observed by injecting low salinity water in carbonated reservoirs. pH plays a fundamental role in the surface chemistry of oil/brine interfaces, and wettability. Our contact angle results show that formation brine triggered a strong water-wet system (35°) at pH 2.55, yet 100 times diluted formation brine led to a strongly oil-wet system (contact angle = 175°) at pH 5.68. Surface complexation modelling correctly predicted the wettability trend with salinity; the bond product sum ([>CaOH 2 +][–COO -] + [>CO 3 -][–NH +] + [>CO 3 -][–COOCa +]) increased with decreasing salinity. Finally, at pH < 6 dilution likely makes the calcite surface oil-wet, particularly for crude oils with high base number. Yet, dilution probably causes water wetness at pH > 7 for crude oils with high acid number.« less

Adverse Effects of Induced Hot Flashes on Objectively Recorded and Subjectively Reported Sleep: Results of a Gonadotropin-Releasing Hormone Agonist Experimental Protocol

PubMed Central

Joffe, Hadine; White, David P.; Crawford, Sybil L.; McCurnin, Kristin E.; Economou, Nicole; Connors, Stephanie; Hall, Janet E.

2013-01-01

Objectives The impact of hot flashes on sleep is of great clinical interest, but results are inconsistent, especially when both hot flashes and sleep are measured objectively. Using objective and subjective measurements, we examined the impact of hot flashes on sleep by inducing hot flashes with a gonadotropin-releasing hormone agonist (GnRHa). Methods The GnRHa leuprolide was administered to 20 healthy premenopausal volunteers without hot flashes or sleep disturbances. Induced hot flashes were assessed objectively (skin-conductance monitor) and subjectively (daily diary) during one-month follow-up. Changes from baseline in objective (actigraphy) and subjective sleep quality (Pittsburgh Sleep Quality Index [PSQI]) were compared between women who did and did not develop objective hot flashes, and, in parallel analyses, subjective hot flashes. Results New-onset hot flashes were recorded in 14 (70%) and reported by 14 (70%) women (80% concordance). Estradiol was universally suppressed. Objective sleep efficiency worsened in women with objective hot flashes and improved in women without objective hot flashes (median decrease 2.6%, increase 4.2%, p=0.005). Subjective sleep quality worsened more in those with than without subjective hot flashes (median increase PSQI 2.5 vs. 1.0, p=0.03). Objective hot flashes were not associated with subjective sleep quality, nor were subjective symptoms linked to objective sleep measures. Conclusions This experimental model of induced hot flashes demonstrates a causal relationship between hot flashes and poor sleep quality. Objective hot flashes result in worse objective sleep efficiency, while subjective hot flashes worsen perceived sleep quality. PMID:23481119

Pharmacological profile of the aerial parts of Rubus ulmifolius Schott.

PubMed

Ali, Niaz; Shaoib, Mohammad; Shah, Syed Wadood Ali; Shah, Ismail; Shuaib, Muhammad

2017-01-19

As aerial parts of Rubus ulmifolius contains phytochemicals like flavonoids and tannins. And whereas flavonoids and tannins have antioxidant and antipyretic activity, hence, current work is carried out to screen crude methanolic extract of aerial parts of Rubus ulmifolius (Ru.Cr) and crude flavonoids rich extract of Rubus ulmifolius (Ru.F) for possible antioxidant and antipyretic activity. Ru.Cr and Ru.F are also tested for brine shrimps lethality bioassay. Ru.F is tested for the first time for possible antioxidant and antipyretic activity. Preliminary phytochemical screening of Ru.Cr and Ru.F was performed as it provides rapid finger printing for targeting a pharmacological activity. Acute toxicity and Brine shrimps' cytotoxicity studies of Ru.Cr and Ru.F were performed to determine its safe dose range. Antioxidant and antipyretic studies were also performed as per reported procedures. Ru.Cr tested positive for presence of tannins, alkaloids, flavonoids and steroids. Ru.Cr is safe up to 6 g/kg following oral doses for acute toxicity study. Ru.Cr is safe up to 75 μg/kg (p.o), LC 50 for Ru.Cr and Ru.F are 16.7 ± 1.4 μg/ml 10.6 ± 1.8 μg/ml, respectively (n = 3). Both Ru.Cr and Ru.F demonstrated comparable antioxidant activity using vitamin C as standard (p ≤ 0.05). In test dose of 300 mg of Ru.Cr, rectal temperature was reduced by 74% (p ≤ 0.05) on 4 th hour of the administration. More, Ru.F produced 72% reduction in pyrexia (p ≤ 0.05) on 4 th hour of administration of paracetamol in Westar rats. The current work confirms that aerial parts of Rubus ulmifolius contain flavonoids that are safe up to 6 g/kg (p.o). Crude methanolic extract and flavonoids rich fraction of Rubus ulmifolius have significant antioxidant and antipyretic activity. Further work is required to isolate the pharmacologically active substances for relatively safe and effective antipyretics and antioxidants.

Menopausal hot flashes: Randomness or rhythmicity

NASA Astrophysics Data System (ADS)

Kronenberg, Fredi

1991-10-01

Menopausal hot flashes are episodes of flushing, increased heart rate, skin blood flow and skin temperature, and a sensation of heat. The thermoregulatory and cardiovascular concomitants of hot flashes are associated with peaks in the levels of various hormones and neurotransmitters in the peripheral circulation. Although hot flashes affect about 75% of women, and are the primary reason that women at menopause seek medical attention, the mechanism of hot flashes is still not understood. Hot flashes vary in frequency and intensity both within and between individuals, and have been thought of as occurring randomly. Yet, some women report that their hot flashes are worse at a particular time of day or year. Initial examination of subjects' recordings of their hot flashes showed diurnal patterns of hot flash occurrence. There also seems to be a diurnal rhythm of hot flash intensity. Continuous physiological monitoring of hot flashes is facilitating the analysis of these patterns, which is revealing circadian and ultradian periodicities. The occurrence of hot flashes can be modulated by external and internal factors, including ambient temperature and fever. Rhythms of thermoregulatory and endocrine functions also may influence hot flash patterns. Examination of the interrelationships between the various systems of the body involved in hot flashes, and a multidisciplinary approach to the analysis of hot flash patterns, will aid our understanding of this complex phenomenon.

Evaluation of Glider Coatings Against Biofouling for Improved Flight Performance

DTIC Science & Technology

2011-08-17

and used to conduct assays of survivorship with approximately 100 nauplii larvae ofArtemia sp. (brine shrimp ). The larvae were exposed to the...seal (D). These coatings showed higher mortality of brine shrimp as well as 100% mortality of cypris larvae during the settlement assay which...brine shrimp compared to the glass control; however these did not inhibit settlement and were evidently not toxic to the cypris larvae . All other

The densities of halite-saturated WIPP-A and NBT-6 brines and their NaCl contents in weight percent, molal, and molar units from 20 to 100 degrees C

USGS Publications Warehouse

Chou, I-Ming; Buizinga, B.; Clynne, M.A.; Potter, R.W.

1982-01-01

A series of density measurements has been performed at 30?, 50?, 70?, and 90?C for halite-undersaturated WIPP-A and NBT-6 brines with various NaCl contents approaching saturation. The densities of halite-saturated WIPP-A and NBT-6 brines were obtained by extrapolating these measured densities to halite saturation points. The maximum difference between the densities obtained in this Fashion and those calculated from the model of Potter and Haas is 0.015 g/cm3. The NaCl contents in halite-saturated WIPP-A and NBT-6 brines are reported in wt %, molal, and molar units from 20? to 100?C.

Temporary Urine and Brine Stowage System (TUBSS) Development

NASA Technical Reports Server (NTRS)

Dries, Kevin; Carrigan, Caitlin

2011-01-01

International Space Station (ISS) crew liquid human waste is treated with chromic and sulfuric acids to maintain stability prior to processing to recover water. This pre-treated urine (PTU) and its processed by-product, brine, are highly toxic fluids that require special containment for on-orbit stowage. The temporary urine and brine stowage syste m (TUBSS) is an assembly used to store and transfer pre-treated urine (PTU) and brine for processing or disposal at a later date. This paper describes the development of the TUBSS, including design for two-fault tolerance and materials selection to maintain a soft, collapsible container. In addition, this paper will provide results of testing as well as lessons learned from the project, culminating in the successful launch of the hardware.

A randomized, controlled, double-blinded clinical trial of gabapentin 300 versus 900 mg versus placebo for anxiety symptoms in breast cancer survivors.

PubMed

Lavigne, Jill E; Heckler, Charles; Mathews, Jennifer L; Palesh, Oxana; Kirshner, Jeffrey J; Lord, Raymond; Jacobs, Andrew; Amos, Eric; Morrow, Gary R; Mustian, Karen

2012-11-01

Gabapentin is used for the treatment of hot flashes and neuropathic pain in breast cancer survivors, and is commonly used off-label for the treatment of anxiety. Yet, clinical trial evidence to support the use of gabapentin for anxiety symptoms is lacking. In a randomized, double-blinded controlled trial we compared 300 mg gabapentin versus 900 mg gabapentin versus placebo. Subjects were 420 breast cancer patients who had completed all chemotherapy cycles. Anxiety traits and current (state) anxiety were measured using the Speilberger Strait-Trait Anxiety Inventory at baseline, 4 and 8 weeks. Pain was measured at baseline using a 10-point scale. Analyses included analysis of covariance and ordinary least squares regression. At 4 weeks, state anxiety change scores were significantly better for gabapentin 300 and 900 mg (p = 0.005) compared to placebo. The magnitude of improvement was proportional to baseline state anxiety. At 8 weeks, the anxiolytic effects of gabapentin compared to placebo persisted (p < 0.005). We found no significant interactions. The lower dose (300 mg) was associated with the best treatment outcomes for all patients except those with the highest baseline anxiety. Given its similar pharmacology, efficacy in the treatment of hot flashes, and low cost, gabapentin may provide a low cost and parsimonious alternative treatment choice for breast cancer survivors presenting in primary care practices with anxiety symptoms. Gabapentin is effective for hot flashes, and, therefore, may provide therapeutic benefit for both anxiety and hot flashes at a generic drug price. For patients reluctant to take a controlled substance, such as a benzodiazepine, gabapentin may offer an alternative therapy. Similarly, patients with a history of substance use may benefit from gabapentin without risk of addiction or abuse. For cancer survivors experiencing both hot flashes and anxiety, gabapentin may provide a single effective treatment for both and is an alternative therapy for anxiety for patients unwilling to take a benzodiazepine or those with a history of substance use.

The origin of brines and salts in Chilean salars: a hydrochemical review

NASA Astrophysics Data System (ADS)

Risacher, François; Alonso, Hugo; Salazar, Carlos

2003-11-01

Northern Chile is characterized by a succession of north-south-trending ranges and basins occupied by numerous saline lakes and salt crusts, collectively called salars. Fossil salt crusts are found to the west in the extremely arid Central Valley, while active salars receiving permanent inflows fill many intravolcanic basins to the east in the semiarid Cordillera. Sea salts and desert dust are blown eastward over the Cordillera, where they constitute an appreciable fraction of the solute load of very dilute waters (salt content<0.1 g/l). The weathering of volcanic rocks contributes most components to inflow waters with salt content ranging from 0.1 to 0.6 g/l. However, the average salt content of all inflows is much higher: about 3.2 g/l. Chemical composition, Cl/Br ratio, and 18O- 2H isotope contents point to the mixing of very dilute meteoric waters with present lake brines for the origin of saline inflows. Ancient gypsum in deep sedimentary formations seems to be the only evaporitic mineral recycled in present salars. Saline lakes and subsurface brines are under steady-state regime. The average residence time of conservative components ranges from a few years to some thousands years, which indicates a permanent leakage of the brines through bottom sediments. The infiltrating brines are recycled in the hydrologic system where they mix with dilute meteoric waters. High heat flow is the likely driving force that moves the deep waters in this magmatic arc region. Active Chilean salars cannot be considered as terminal lakes nor, strictly speaking, as closed basin lakes. Almost all incoming salts leave the basin and are transported elsewhere. Moreover, the dissolution of fossil salt crusts in some active salars also carries away important fluxes of components in percolating brines. Evaporative concentration of inflow waters leads to sulfate-rich or calcium-rich, near-neutral brines. Alkaline brines are almost completely lacking. The alkalinity/calcium ratio of inflow waters is lowered by the oxidation of native sulfur (reducing alkalinity) and the deposition of eolian gypsum (increasing Ca concentration). Theoretically, SO 4-rich inflow waters and their derived SO 4-rich brines should be found in the intravolcanic basins of the Cordillera because of the ubiquity of native sulfur, while Ca-rich brines should prevail in sedimentary basins where Ca-rich minerals are abundant. This relation is perfectly observed in the salar de Atacama, the largest in Chile. However, several salars located within the volcanic Cordillera belong to the Ca-rich group. Inflows and brines may have acquired their Ca-rich composition in Pleistocene time when their drainage basins were mainly sedimentary. Later on, recent lava flows and ignimbrites covered the sedimentary formations. Underground waters may have kept their early sedimentary signature by continuous recycling. However, the weathering of volcanic rocks tend to slowly shift the water compositions from the Ca-rich to the SO 4-rich type.

Inactivation of Shiga toxin-producing O157:H7 and non-O157:H7 Shiga toxin-producing Escherichia coli in brine-injected, gas-grilled steaks.

PubMed

Luchansky, John B; Porto-Fett, Anna C S; Shoyer, Bradley A; Call, Jeffrey E; Schlosser, Wayne; Shaw, William; Bauer, Nathan; Latimer, Heejeong

2011-07-01

We quantified translocation of Escherichia coli O157:H7 (ECOH) and non-O157:H7 verocytotoxigenic E. coli (STEC) into beef subprimals after brine injection and subsequently monitored their viability after cooking steaks cut therefrom. Beef subprimals were inoculated on the lean side with ca. 6.0 log CFU/g of a five-strain cocktail of rifampin-resistant ECOH or kanamycin-resistant STEC, and then passed once through an automatic brine-injector tenderizer, with the lean side facing upward. Brine solutions (9.9% ± 0.3% over fresh weight) consisted of 3.3% (wt/vol) of sodium tripolyphosphate and 3.3% (wt/vol) of sodium chloride, prepared both with (Lac(+), pH = 6.76) and without (Lac(-), pH = 8.02) a 25% (vol/vol) solution of a 60% potassium lactate-sodium diacetate syrup. For all samples injected with Lac(-) or Lac(+) brine, levels of ECOH or STEC recovered from the topmost 1 cm (i.e., segment 1) of a core sample obtained from tenderized subprimals ranged from ca. 4.7 to 6.3 log CFU/g; however, it was possible to recover ECOH or STEC from all six segments of all cores tested. Next, brine-injected steaks from tenderized subprimals were cooked on a commercial open-flame gas grill to internal endpoint temperatures of either 37.8 °C (100 °F), 48.8 °C (120 °F), 60 °C (140 °F), or 71.1 °C (160 °F). Regardless of brine formulation or temperature, cooking achieved reductions (expressed as log CFU per gram) of 0.3 to 4.1 of ECOH and 0.5 to 3.6 of STEC. However, fortuitous survivors were recovered even at 71.1 °C (160 °F) for ECOH and for STEC. Thus, ECOH and STEC behaved similarly, relative to translocation and thermal destruction: Tenderization via brine injection transferred both pathogens throughout subprimals and cooking highly contaminated, brine-injected steaks on a commercial gas grill at 71.1 °C (160 °F) did not kill all cells due, primarily, to nonuniform heating (i.e., cold spots) within the meat. Copyright ©, International Association for Food Protection

Multiphase flow of carbon dioxide and brine in dual porosity carbonates

NASA Astrophysics Data System (ADS)

Pentland, Christopher; Oedai, Sjaam; Ott, Holger

2014-05-01

The storage of carbon dioxide in subsurface formations presents a challenge in terms of multiphase flow characterisation. Project planning requires an understanding of multiphase flow characteristics such as the relationship between relative permeability and saturation. At present there are only a limited number of relative permeability relations for carbon dioxide-brine fluid systems, most of which are measured on sandstone rocks. In this study coreflood experiments are performed to investigate the relative permeability of carbon dioxide and brine in two dual porosity carbonate systems. Carbon dioxide is injected into the brine saturated rocks in a primary drainage process. The rock fluid system is pre-equilibrated to avoid chemical reactions and physical mass transfer between phases. The pressure drop across the samples, the amount of brine displaced and the saturation distribution within the rocks are measured. The experiments are repeated on the same rocks for the decane-brine fluid system. The experimental data is interpreted by simulating the experiments with a continuum scale Darcy solver. Selected functional representations of relative permeability are investigated, the parameters of which are chosen such that a least squares objective function is minimised (i.e. the difference between experimental observations and simulated response). The match between simulation and measurement is dependent upon the form of the functional representations. The best agreement is achieved with the Corey [Brooks and Corey, 1964] or modified Corey [Masalmeh et al., 2007] functions which best represent the relative permeability of brine at low brine saturations. The relative permeability of carbon dioxide is shown to be lower than the relative permeability of decane over the saturation ranges investigated. The relative permeability of the brine phase is comparable for the two fluid systems. These observations are consistent with the rocks being water-wet. During the experiment only a portion of the full saturation range is investigated, corresponding to carbon dioxide entering the macro pores of the dual porosity systems. Within this pore space the relative permeability behaviour is comparable to that measured in Berea sandstone. Brooks, R. H., and A. T. Corey (1964), Hydraulic properties of porous media, Hydrology Papers 3, Civil Engineering Dept., Colorado State Univ., Fort Collins, CO. Masalmeh, S., I. Abu-Shiekah, and X. Jing (2007), Improved Characterization and Modeling of Capillary Transition Zones in Carbonate Reservoirs, SPE Reserv. Eval. Eng., 10(2), doi:10.2118/109094-PA.

Multi-dimensional Imaging and Characterization of Convective Mixing in a Porous Media

NASA Astrophysics Data System (ADS)

Liyanage, R.; Pini, R.; Crawshaw, J.; Krevor, S. C.

2017-12-01

The dissolution of CO2 into reservoir brines is one of the key trapping mechanisms during CO2 sequestration in deep saline aquifers. The dissolution at the CO2-brine interface induces a buoyant instability in the aqueous phase following a local brine density increase in the range of 0.1-1% depending on pressure, temperature, and salinity. As a result the CO2 -saturated brine mixes with fresh brine to form characteristic finger-like patterns. This downward flow pushes fresh brine to the CO2-brine interface and further enhances dissolution. This phenomenon is referred to as convective mixing. A study has been undertaken to investigate convective mixing in a 3D opaque porous medium. A novel protocol is presented using X-ray Computed Tomography (X-ray CT) to image the evolution of convective mixing over time. Results are presented for experiments carried out at ambient conditions using a spherical bowl (diameter of 20 cm) packed with glass beads (diameter, 0.5 mm). Surrogate fluids are used that provide good x-ray contrast whilst maintaining a maximum density differential comparable to the one observed in a supercritical CO2-brine system (about 10 kg/m3). We use a mixture of methanol and ethylene glycol (MEG) at three different ratios (and doped with KI) and brine. We perform two repeats for each fluid pair and during a typical experiment scans are taken at regular time intervals for up to 10 hours. 3D images of the bowl are reconstructed (fig. 1) with (2x2x2) mm3 voxels. The experiments are classified by Rayleigh number covering the range Ra = 5,000-25,000. As expected, higher Ra leads to early development of instability, with the plume moving faster towards the bottom of the bowl. The computed dissolution flux supports these visual observations and confirms that dissolutions enhanced mixing produces fluxes that are significantly larger than the corresponding purely diffusive scenario. While quantitative agreement is observed from repeated experiments, we note that the characteristic microscopic features differs (e.g. finger distribution), even when a homogenous packing is considered. We observe that mixing is not necessarily more efficient with a higher Ra, as in a closed domain the faster movement of the plume towards the bottom leads to an early convective shutdown and a situation that is solely controlled by diffusion.

Nutritive Supplements - Help or Harm for Breast Cancer Patients?

PubMed

Muenstedt, Karsten; El-Safadi, Samer

2010-01-01

SUMMARY: Considerable numbers of patients and physicians believe that micronutrients may be useful with respect to prevention and treatment of breast cancer. However, the analysis of the literature shows that basic information on nutritional demands in cancer patients is lacking. It is unknown whether there is an increased demand of micro-nutrients in cancer patients in general and if there is an even more increased demand during the various types of treatment. As a result, there are only limited positive findings. Higher calcium intake in premenopausal women and higher intake of vitamin D seem to be able to lower breast cancer incidence. Vitamin E (800 IU per day) was found to have a modest effect on hot flashes during tamoxifen treatment. However, there are potential side effects especially when micronutrients are administered in high or very high doses. There is increasing evidence that dose-effect relationships are not linear but U-shaped. It seems that two thresholds exist for adverse effect, one at low doses for undersupply, and another at high doses for toxicity. Thus, arbitrary high-dose administration of micronutrients should be avoided. Supplementation of normal doses seems to be safe and acceptable from the medical point of view.

Evaluation of a hybrid ion exchange-catalyst treatment technology for nitrate removal from drinking water.

PubMed

Bergquist, Allison M; Choe, Jong Kwon; Strathmann, Timothy J; Werth, Charles J

2016-06-01

Ion exchange (IX) is the most common approach to treating nitrate-contaminated drinking water sources, but the cost of salt to make regeneration brine, as well as the cost and environmental burden of waste brine disposal, are major disadvantages. A hybrid ion exchange-catalyst treatment system, in which waste brine is catalytically treated for reuse, shows promise for reducing costs and environmental burdens of the conventional IX system. An IX model with separate treatment and regeneration cycles was developed, and ion selectivity coefficients for each cycle were separately calibrated by fitting experimental data. Of note, selectivity coefficients for the regeneration cycle required fitting the second treatment cycle after incomplete resin regeneration. The calibrated and validated model was used to simulate many cycles of treatment and regeneration using the hybrid system. Simulated waste brines and a real brine obtained from a California utility were also evaluated for catalytic nitrate treatment in a packed-bed, flow-through column with 0.5 wt%Pd-0.05 wt%In/activated carbon support (PdIn/AC). Consistent nitrate removal and no apparent catalyst deactivation were observed over 23 d (synthetic brine) and 45 d (real waste brine) of continuous-flow treatment. Ion exchange and catalyst results were used to evaluate treatment of 1 billion gallons of nitrate-contaminated source water at a 0.5 MGD water treatment plant. Switching from a conventional IX system with a two bed volume regeneration to a hybrid system with the same regeneration length and sequencing batch catalytic reactor treatment would save 76% in salt cost. The results suggest the hybrid system has the potential to address the disadvantages of a conventional IX treatment systems. Copyright © 2016 Elsevier Ltd. All rights reserved.

Laboratory flow experiments for visualizing carbon dioxide-induced, density-driven brine convection

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kneafsey, T.; Pruess, K.

2009-09-01

Injection of carbon dioxide (CO{sub 2}) into saline aquifers confined by low-permeability cap rock will result in a layer of CO{sub 2} overlying the brine. Dissolution of CO{sub 2} into the brine increases the brine density, resulting in an unstable situation in which more-dense brine overlies less-dense brine. This gravitational instability could give rise to density-driven convection of the fluid, which is a favorable process of practical interest for CO{sub 2} storage security because it accelerates the transfer of buoyant CO{sub 2} into the aqueous phase, where it is no longer subject to an upward buoyant drive. Laboratory flow visualizationmore » tests in transparent Hele-Shaw cells have been performed to elucidate the processes and rates of this CO{sub 2} solute-driven convection (CSC). Upon introduction of CO{sub 2} into the system, a layer of CO{sub 2}-laden brine forms at the CO{sub 2}-water interface. Subsequently, small convective fingers form, which coalesce, broaden, and penetrate into the test cell. Images and time-series data of finger lengths and wavelengths are presented. Observed CO{sub 2} uptake of the convection system indicates that the CO{sub 2} dissolution rate is approximately constant for each test and is far greater than expected for a diffusion-only scenario. Numerical simulations of our system show good agreement with the experiments for onset time of convection and advancement of convective fingers. There are differences as well, the most prominent being the absence of cell-scale convection in the numerical simulations. This cell-scale convection observed in the experiments is probably initiated by a small temperature gradient induced by the cell illumination.« less

Brine assemblages of ultrasmall microbial cells within the ice cover of Lake Vida, Antarctica.

PubMed

Kuhn, Emanuele; Ichimura, Andrew S; Peng, Vivian; Fritsen, Christian H; Trubl, Gareth; Doran, Peter T; Murray, Alison E

2014-06-01

The anoxic and freezing brine that permeates Lake Vida's perennial ice below 16 m contains an abundance of very small (≤0.2-μm) particles mixed with a less abundant population of microbial cells ranging from >0.2 to 1.5 μm in length. Fluorescent DNA staining, electron microscopy (EM) observations, elemental analysis, and extraction of high-molecular-weight genomic DNA indicated that a significant portion of these ultrasmall particles are cells. A continuous electron-dense layer surrounding a less electron-dense region was observed by EM, indicating the presence of a biological membrane surrounding a cytoplasm. The ultrasmall cells are 0.192 ± 0.065 μm, with morphology characteristic of coccoid and diplococcic bacterial cells, often surrounded by iron-rich capsular structures. EM observations also detected the presence of smaller unidentified nanoparticles of 0.020 to 0.140 μm among the brine cells. A 16S rRNA gene clone library from the brine 0.1- to 0.2-μm-size fraction revealed a relatively low-diversity assemblage of Bacteria sequences distinct from the previously reported >0.2-μm-cell-size Lake Vida brine assemblage. The brine 0.1- to 0.2-μm-size fraction was dominated by the Proteobacteria-affiliated genera Herbaspirillum, Pseudoalteromonas, and Marinobacter. Cultivation efforts of the 0.1- to 0.2-μm-size fraction led to the isolation of Actinobacteria-affiliated genera Microbacterium and Kocuria. Based on phylogenetic relatedness and microscopic observations, we hypothesize that the ultrasmall cells in Lake Vida brine are ultramicrocells that are likely in a reduced size state as a result of environmental stress or life cycle-related conditions.

Two-phase convective CO 2 dissolution in saline aquifers

DOE PAGES

Martinez, Mario J.; Hesse, Marc A.

2016-01-30

Geologic carbon storage in deep saline aquifers is a promising technology for reducing anthropogenic emissions into the atmosphere. Dissolution of injected CO 2 into resident brines is one of the primary trapping mechanisms generally considered necessary to provide long-term storage security. Given that diffusion of CO 2 in brine is woefully slow, convective dissolution, driven by a small increase in brine density with CO 2 saturation, is considered to be the primary mechanism of dissolution trapping. Previous studies of convective dissolution have typically only considered the convective process in the single-phase region below the capillary transition zone and have eithermore » ignored the overlying two-phase region where dissolution actually takes place or replaced it with a virtual region with reduced or enhanced constant permeability. Our objective is to improve estimates of the long-term dissolution flux of CO 2 into brine by including the capillary transition zone in two-phase model simulations. In the fully two-phase model, there is a capillary transition zone above the brine-saturated region over which the brine saturation decreases with increasing elevation. Our two-phase simulations show that the dissolution flux obtained by assuming a brine-saturated, single-phase porous region with a closed upper boundary is recovered in the limit of vanishing entry pressure and capillary transition zone. For typical finite entry pressures and capillary transition zone, however, convection currents penetrate into the two-phase region. As a result, this removes the mass transfer limitation of the diffusive boundary layer and enhances the convective dissolution flux of CO 2 more than 3 times above the rate assuming single-phase conditions.« less

Metabolomics and the Legacy of Previous Ecosystems: a Case Study from the Brine of Lake Vida (Antarctica)

NASA Astrophysics Data System (ADS)

Chou, L.; Kenig, F. P. H.; Murray, A. E.; Doran, P. T.; Fritsen, C. H.

2015-12-01

The McMurdo Dry Valleys of Antarctica are regarded as one of the best Earth analogs for astrobiological investigations of icy worlds. In the dry valleys, Lake Vida contains an anoxic and aphotic ice-sealed brine that has been isolated for millennia and yet is hosting a population of active microbes at -13˚ C. The biogeochemical processes used by these slow-growing microbes are still unclear. We attempt to elucidate the microbial processes responsible for the survivability of these organisms using metabolomics. Preliminary investigations of organic compounds of Lake Vida Brine (LVBr) was performed using gas chromatography-mass spectrometry (GC-MS) and solid-phase micro-extraction (SPME) GC-MS. LVBr contains a vast variety of lipids and is dominated by low molecular weight compounds. Many of these compounds are biomarkers of processes that took place in Lake Vida prior to evaporation and its cryo-encapsulation. These compounds include dimethylsulfide that is derived from the photosynthate dimethylsulfoniopropionate, dihydroactinidiolide that is derived from a diatom pigment, and 2-methyl-3-ethyl-maleimide that is derived from chlorophyll. These compounds, which dominate the lipid reservoir, represent a legacy from an ecosystem that is different from the current bacterial ecosystem of the brine. The abundance of the legacy compounds in the brine is most likely a reflection of the very slow metabolism of the bacterial community in the cold brine. It is important, thus, to be able to distinguish the legacy metabolites and their diagenetic products from the metabolites of the current ecosystem. This legacy issue is specific to a slow growing microbial ecosystem that cannot process the legacy carbon completely. It applies not only to Lake Vida brine, but other slow growing ecosystems such as other subglacial Antarctic lakes, the Arctic regions, and the deep biosphere.

Brine Assemblages of Ultrasmall Microbial Cells within the Ice Cover of Lake Vida, Antarctica

PubMed Central

Kuhn, Emanuele; Ichimura, Andrew S.; Peng, Vivian; Fritsen, Christian H.; Trubl, Gareth; Doran, Peter T.

2014-01-01

The anoxic and freezing brine that permeates Lake Vida's perennial ice below 16 m contains an abundance of very small (≤0.2-μm) particles mixed with a less abundant population of microbial cells ranging from >0.2 to 1.5 μm in length. Fluorescent DNA staining, electron microscopy (EM) observations, elemental analysis, and extraction of high-molecular-weight genomic DNA indicated that a significant portion of these ultrasmall particles are cells. A continuous electron-dense layer surrounding a less electron-dense region was observed by EM, indicating the presence of a biological membrane surrounding a cytoplasm. The ultrasmall cells are 0.192 ± 0.065 μm, with morphology characteristic of coccoid and diplococcic bacterial cells, often surrounded by iron-rich capsular structures. EM observations also detected the presence of smaller unidentified nanoparticles of 0.020 to 0.140 μm among the brine cells. A 16S rRNA gene clone library from the brine 0.1- to 0.2-μm-size fraction revealed a relatively low-diversity assemblage of Bacteria sequences distinct from the previously reported >0.2-μm-cell-size Lake Vida brine assemblage. The brine 0.1- to 0.2-μm-size fraction was dominated by the Proteobacteria-affiliated genera Herbaspirillum, Pseudoalteromonas, and Marinobacter. Cultivation efforts of the 0.1- to 0.2-μm-size fraction led to the isolation of Actinobacteria-affiliated genera Microbacterium and Kocuria. Based on phylogenetic relatedness and microscopic observations, we hypothesize that the ultrasmall cells in Lake Vida brine are ultramicrocells that are likely in a reduced size state as a result of environmental stress or life cycle-related conditions. PMID:24727273

Gas-water-rock interactions in Frio Formation following CO2 injection: Implications for the storage of greenhouse gases in sedimentary basins

USGS Publications Warehouse

Kharaka, Yousif K.; Cole, David R.; Hovorka, Susan D.; Gunter, W.D.; Knauss, Kevin G.; Freifeild, Barry M.

2006-01-01

To investigate the potential for the geologic storage of CO2 in saline sedimentary aquifers, 1600 t of CO2 were injected at 1500 m depth into a 24-m-thick sandstone section of the Frio Formation, a regional brine and oil reservoir in the U.S. Gulf Coast. Fluid samples obtained from the injection and observation wells before CO2 injection showed a Na-Ca-Cl–type brine with 93,000 mg/L total dissolved solids (TDS) at near saturation with CH4 at reservoir conditions. Following CO2 breakthrough, samples showed sharp drops in pH (6.5–5.7), pronounced increases in alkalinity (100–3000 mg/L as HCO3) and Fe (30–1100 mg/L), and significant shifts in the isotopic compositions of H2O, dissolved inorganic carbon (DIC), and CH4. Geochemical modeling indicates that brine pH would have dropped lower but for the buffering by dissolution of carbonate and iron oxyhydroxides. This rapid dissolution of carbonate and other minerals could ultimately create pathways in the rock seals or well cements for CO2 and brine leakage. Dissolution of minerals, especially iron oxyhydroxides, could mobilize toxic trace metals and, where residual oil or suitable organics are present, the injected CO2 could also mobilize toxic organic compounds. Environmental impacts could be major if large brine volumes with mobilized toxic metals and organics migrated into potable groundwater. The δ18O values for brine and CO2 samples indicate that supercritical CO2 comprises ∼50% of pore-fluid volume ∼6 mo after the end of injection. Postinjection sampling, coupled with geochemical modeling, indicates that the brine gradually will return to its preinjection composition.

Survival of Listeria monocytogenes in a simulated recirculating brine chiller system.

PubMed

Gailey, J K; Dickson, J S; Dorsa, W

2003-10-01

Contamination by Listeria monocytogenes of processed meats after cooking presents a significant food safety risk. The purpose of this study was to determine the survival of L. monocytogenes in a simulated recirculating brine chiller system using pH values of 5, 6, and 7 with free chlorine concentrations of 0, 3, 5, and 10 ppm in 20% salt brine at -12 degrees C. At pH values of 5, 6, and 7 with chlorine concentrations of 2 and 3 ppm, using 10(8) CFU in a test tube system, an immediate drop of 0.28 log CFU/ml with no significance between treatments (P > 0.05), followed by a steady survival phase with a slope close to 0, was observed. In brine at a pH of 5 with 5 and 10 ppm of chlorine, an initial drop of 0.8 log CFU/ml was observed, which was followed by a steady survival phase with a destruction slope close to zero. At an inoculation concentration of 10(2) CFU in a test tube system (pH values of 5 and 7 with 0 and 10 ppm of chlorine), the average initial drop for all treatments was 0.1 log CFU/ml, which was followed by a steady survival phase. In a recirculating system, very few cells were destroyed during the brine chilling process, but only low numbers of L. monocytogenes were recovered from the brine and uninoculated hot dogs. Although little destruction of L. monocytogenes was noted, the dilution effect observed during the study indicates that environmental contamination of a brine chiller system poses little danger of postcooking contamination for processed meats if the system is regularly cleaned and sanitized.

Efficacy of chlorine dioxide against Listeria monocytogenes in brine chilling solutions.

PubMed

Valderrama, W B; Mills, E W; Cutter, C N

2009-11-01

Chilled brine solutions are used by the food industry to rapidly cool ready-to-eat meat products after cooking and before packaging. Chlorine dioxide (ClO(2)) was investigated as an antimicrobial additive to eliminate Listeria monocytogenes. Several experiments were performed using brine solutions made of sodium chloride (NaCl) and calcium chloride (CaCl(2)) inoculated with L. monocytogenes and/or treated with 3 ppm of ClO(2). First, 10 and 20% CaCl(2) and NaCl solutions (pH 7.0) were inoculated with a five-strain cocktail of L. monocytogenes to obtain approximately 7 log CFU/ml and incubated 8 h at 0 degrees C. The results demonstrated that L. monocytogenes survived in 10% CaCl(2), 10 and 20% NaCl, and pure water. L. monocytogenes levels were reduced approximately 1.2 log CFU/ml in 20% CaCl(2). Second, inoculated ( approximately 7 log CFU/ml) brine solutions (10 and 20% NaCl and 10% CaCl(2)) treated with 3 ppm of ClO(2) resulted in a approximately 4-log reduction of the pathogen within 90 s. The same was not observed in a solution of 20% CaCl(2); further investigation demonstrated that high levels of divalent cations interfere with the disinfectant. Spent brine solutions from hot dog and ham chilling were treated with ClO(2) at concentrations of 3 or 30 ppm. At these concentrations, ClO(2) did not reduce L. monocytogenes. Removal of divalent cations and organic material in brine solutions prior to disinfection with ClO(2) should be investigated to improve the efficacy of the compound against L. monocytogenes. The information from this study may be useful to processing establishments and researchers who are investigating antimicrobials in chilling brine solutions.

Potential Hydrogeomechanical Impacts of Geological CO2 Sequestration

NASA Astrophysics Data System (ADS)

McPherson, B. J.; Haerer, D.; Han, W.; Heath, J.; Morse, J.

2006-12-01

Long-term sequestration of anthropogenic "greenhouse gases" such as CO2 is a proposed approach to managing climate change. Deep brine reservoirs in sedimentary basins are possible sites for sequestration, given their ubiquitous nature. We used a mathematical sedimentary basin model, including coupling of multiphase CO2-groundwater flow and rock deformation, to evaluate residence times in possible brine reservoir storage sites, migration patterns and rates away from such sites, and effects of CO2 injection on fluid pressures and rock strain. Study areas include the Uinta and Paradox basins of Utah, the San Juan basin of New Mexico, and the Permian basin of west Texas. Regional-scale hydrologic and mechanical properties, including the presence of fracture zones, were calibrated using laboratory and field data. Our initial results suggest that, in general, long-term (~100 years or more) sequestration in deep brine reservoirs is possible, if guided by robust structural and hydrologic data. However, specific processes must be addressed to characterize and minimize risks. In addition to CO2 migration from target sequestration reservoirs into other reservoirs or to the land surface, another environmental issue is displacement of brines into freshwater aquifers. We evaluated the potential for such unintended aquifer contamination by displacement of brines out of adjacent sealing layers such as marine shales. Results suggest that sustained injection of CO2 may incur significant brine displacement out of adjacent sealing layers, depending on the injection history, initial brine composition, and hydrologic properties of both reservoirs and seals. Model simulations also suggest that as injection-induced overpressures migrate, effective stresses may follow this migration under some conditions, as will associated rock strain. Such "strain migration" may lead to induced or reactivated fractures or faults, but can be controlled through reservoir engineering.

An Analysis of Total Lightning Flash Rates Over Florida

NASA Astrophysics Data System (ADS)

Mazzetti, Thomas O.; Fuelberg, Henry E.

2017-12-01

Although Florida is known as the "Sunshine State", it also contains the greatest lightning flash densities in the United States. Flash density has received considerable attention in the literature, but lightning flash rate has received much less attention. We use data from the Earth Networks Total Lightning Network (ENTLN) to produce a 5 year (2010-2014) set of statistics regarding total flash rates over Florida and adjacent regions. Instead of tracking individual storms, we superimpose a 0.2° × 0.2° grid over the study region and count both cloud-to-ground (CG) and in-cloud (IC) flashes over 5 min intervals. Results show that the distribution of total flash rates is highly skewed toward small values, whereas the greatest rate is 185 flashes min-1. Greatest average annual flash rates ( 3 flashes min-1) are located near Orlando. The southernmost peninsula, North Florida, and the Florida Panhandle exhibit smaller average annual flash rates ( 1.5 flashes min-1). Large flash rates > 100 flashes min-1 can occur during any season, at any time during the 24 h period, and at any location within the domain. However, they are most likely during the afternoon and early evening in East Central Florida during the spring and summer months.

Ionic strength dependence of the oxidation of SO2 by H2O2 in sodium chloride particles

NASA Astrophysics Data System (ADS)

Ali, H. M.; Iedema, M.; Yu, X.-Y.; Cowin, J. P.

2014-06-01

The reaction of sulfur dioxide and hydrogen peroxide in the presence of deliquesced (>75% RH) sodium chloride (brine) particles was studied by utilizing a cross flow mini-reactor. The reaction kinetics were followed by observing chloride depletion in particles by computer-controlled scanning electron microscope with energy dispersive X-ray analysis, namely CCSEM/EDX. The reactions take place in concentrated mixed salt brine aerosols, for which no complete kinetic equilibrium data previously existed. We measured the Henry's law solubility of H2O2 in brine solutions to close that gap. We also calculated the reaction rate as the particle transforms continuously from concentrated NaCl brine to, eventually, a mixed NaHSO4 plus H2SO4 brine solution. The reaction rate of the SO2 oxidation by H2O2 was found to be influenced by the change in ionic strength as the particle undergoes compositional transformation, following closely the dependence of the third order rate constant on ionic strength as predicted using established rate equations. This is the first study that has measured the ionic strength dependence of sulfate formation (in non-aqueous media) from oxidation of mixed salt brine aerosols in the presence of H2O2. It also gives the first report of the dependence of the Henry's law constant of H2O2 on ionic strength.

Stability of polyvinyl alcohol-coated biochar nanoparticles in brine

NASA Astrophysics Data System (ADS)

Griffith, Christopher; Daigle, Hugh

2017-01-01

This paper reports on the dispersion stability of 150 nm polyvinyl alcohol coated biochar nanoparticles in brine water. Biochar is a renewable, carbon based material that is of significant interest for enhanced oil recovery operations primarily due to its wide ranging surface properties, low cost of synthesis, and low environmental toxicity. Nanoparticles used as stabilizing agents for foams (and emulsions) or in nanofluids have emerged as potential alternatives to surfactants for subsurface applications due to their improved stability at reservoir conditions. If, however, the particles are not properly designed, they are susceptible to aggregation because of the high salinity brines typical of oil and gas reservoirs. Attachment of polymers to the nanoparticle surface, through covalent bonds, provides steric stabilization, and is a necessary step. Our results show that as the graft density of polyvinyl alcohol increases, so too does the stability of nanoparticles in brine solutions. A maximum of 34 wt% of 50,000 Da polyvinyl alcohol was grafted to the particle surface, and the size of the particles was reduced from 3500 nm (no coating) to 350 nm in brine. After 24 h, the particles had a size of 500 nm, and after 48 h completely aggregated. 100,000 Da PVA coated at 24 wt% on the biochar particles were stable in brine for over 1 month with no change in mean particle size of 330 nm.

Measurement of electrical impedance of a Berea sandstone core during the displacement of saturated brine by oil and CO2 injections

NASA Astrophysics Data System (ADS)

Liu, Yu; Xue, Ziqiu; Park, Hyuck; Kiyama, Tamotsu; Zhang, Yi; Nishizawa, Osamu; Chae, Kwang-seok

2015-12-01

Complex electrical impedance measurements were performed on a brine-saturated Berea sandstone core while oil and CO2 were injected at different pressures and temperatures. The saturations of brine, oil, and CO2 in the core were simultaneously estimated using an X-ray computed tomography scanner. The formation factor of this Berea core and the resistivity indexes versus the brine saturations were calculated using Archie's law. The experimental results found different flow patterns of oil under different pressures and temperatures. Fingers were observed for the first experiment at 10 MPa and 40 °C. The fingers were restrained as the viscosity ratio of oil and water changed in the second (10 MPa and 25 °C) and third (5 MPa and 25 °C) experiments. The resistivity index showed an exponential increase with a decrease in brine saturation. The saturation exponent varied from 1.4 to 4.0 at different pressure and temperature conditions. During the oil injection procedure, the electrical impedance increased with oil saturation and was significantly affected by different oil distributions; therefore, the impedance varied whether the finger was remarkable or not, even if the oil saturation remained constant. During the CO2 injection steps, the impedance showed almost no change with CO2 saturation because the brine in the pores became immobile after the oil injection.

Sodium Hydroxide Production from Seawater Desalination Brine: Process Design and Energy Efficiency.

PubMed

Du, Fengmin; Warsinger, David M; Urmi, Tamanna I; Thiel, Gregory P; Kumar, Amit; Lienhard V, John H

2018-05-15

The ability to increase pH is a crucial need for desalination pretreatment (especially in reverse osmosis) and for other industries, but processes used to raise pH often incur significant emissions and nonrenewable resource use. Alternatively, waste brine from desalination can be used to create sodium hydroxide, via appropriate concentration and purification pretreatment steps, for input into the chlor-alkali process. In this work, an efficient process train (with variations) is developed and modeled for sodium hydroxide production from seawater desalination brine using membrane chlor-alkali electrolysis. The integrated system includes nanofiltration, concentration via evaporation or mechanical vapor compression, chemical softening, further ion-exchange softening, dechlorination, and membrane electrolysis. System productivity, component performance, and energy consumption of the NaOH production process are highlighted, and their dependencies on electrolyzer outlet conditions and brine recirculation are investigated. The analysis of the process also includes assessment of the energy efficiency of major components, estimation of system operating expense and comparison with similar processes. The brine-to-caustic process is shown to be technically feasible while offering several advantages, that is, the reduced environmental impact of desalination through lessened brine discharge, and the increase in the overall water recovery ratio of the reverse osmosis facility. Additionally, best-use conditions are given for producing caustic not only for use within the plant, but also in excess amounts for potential revenue.

Regional-scale brine migration along vertical pathways due to CO2 injection - Part 1: The participatory modeling approach

NASA Astrophysics Data System (ADS)

Scheer, Dirk; Konrad, Wilfried; Class, Holger; Kissinger, Alexander; Knopf, Stefan; Noack, Vera

2017-06-01

Saltwater intrusion into potential drinking water aquifers due to the injection of CO2 into deep saline aquifers is one of the potential hazards associated with the geological storage of CO2. Thus, in a site selection process, models for predicting the fate of the displaced brine are required, for example, for a risk assessment or the optimization of pressure management concepts. From the very beginning, this research on brine migration aimed at involving expert and stakeholder knowledge and assessment in simulating the impacts of injecting CO2 into deep saline aquifers by means of a participatory modeling process. The involvement exercise made use of two approaches. First, guideline-based interviews were carried out, aiming at eliciting expert and stakeholder knowledge and assessments of geological structures and mechanisms affecting CO2-induced brine migration. Second, a stakeholder workshop including the World Café format yielded evaluations and judgments of the numerical modeling approach, scenario selection, and preliminary simulation results. The participatory modeling approach gained several results covering brine migration in general, the geological model sketch, scenario development, and the review of the preliminary simulation results. These results were included in revised versions of both the geological model and the numerical model, helping to improve the analysis of regional-scale brine migration along vertical pathways due to CO2 injection.

Effect of technological factors on the activity and losses of cathepsins B, D and L during the marinating of Atlantic and Baltic herrings.

PubMed

Szymczak, Mariusz

2017-03-01

This study analyzes the effect of salt and acetic acid concentration, time, temperature and fish freezing on the activity and losses of cathepsins during the marinating of Atlantic and Baltic herrings. The highest contribution to meat general proteolytic activity was found for cathepsin D-like activity. This contribution decreased during the marinating process as a result of, among other things, cathepsin losses to brine. The methods of marinating had a significant impact on cathepsin activity losses. The average ratio of cathepsin D-like activity to L and B in brine accounted for 15:3.5:1.5, respectively. Depending on the method of calculation, cathepsin activity in brine was similar (per gram of tissue/milliliter of brine) or multiply higher (per gram protein in tissue/brine) than in the marinated herring meat. Statistical analysis demonstrated that the extent and structure of cathepsin losses were significantly correlated with the quantitative and qualitative composition of protein hydrolysis products in marinades. The presented results depict new phenomena of cathepsin losses and explain their impact on the process of fish marinating. Results allow better optimization of the process of meat ripening. The high activity of aspartyl and cysteine cathepsins in brine indicates the real feasibility of their application in the food industry for novel food design. © 2016 Society of Chemical Industry. © 2016 Society of Chemical Industry.

Behavioral weight loss for the management of menopausal hot flashes: a pilot study.

PubMed

Thurston, Rebecca C; Ewing, Linda J; Low, Carissa A; Christie, Aimee J; Levine, Michele D

2015-01-01

Although adiposity has been considered to be protective against hot flashes, newer data suggest positive relationships between hot flashes and adiposity. No studies have been specifically designed to test whether weight loss reduces hot flashes. This pilot study aimed to evaluate the feasibility, acceptability, and initial efficacy of behavioral weight loss in reducing hot flashes. Forty overweight or obese women with hot flashes (≥ 4 hot flashes/d) were randomized to either behavioral weight loss intervention or wait-list control. Hot flashes were assessed before and after intervention via physiologic monitoring, diary, and questionnaire. Comparisons of changes in hot flashes and anthropometrics between conditions were performed via Wilcoxon tests. Study retention (83%) and intervention satisfaction (93.8%) were high. Most women (74.1%) reported that hot flash reduction was a major motivator for losing weight. Women randomized to the weight loss intervention lost more weight (-8.86 kg) than did women randomized to control (+0.23 kg; P < 0.0001). Women randomized to weight loss also showed greater reductions in questionnaire-reported hot flashes (2-wk hot flashes, -63.0) than did women in the control group (-28.0; P = 0.03)-a difference not demonstrated in other hot flash measures. Reductions in weight and hot flashes were significantly correlated (eg, r = 0.47, P = 0.006). This pilot study shows a behavioral weight loss program that is feasible, acceptable, and effective in producing weight loss among overweight or obese women with hot flashes. Findings indicate the importance of a larger study designed to test behavioral weight loss for hot flash reduction. Hot flash management could motivate women to engage in this health-promoting behavior.

Targeting an efficient target-to-target interval for P300 speller brain–computer interfaces

PubMed Central

Sellers, Eric W.; Wang, Xingyu

2013-01-01

Longer target-to-target intervals (TTI) produce greater P300 event-related potential amplitude, which can increase brain–computer interface (BCI) classification accuracy and decrease the number of flashes needed for accurate character classification. However, longer TTIs requires more time for each trial, which will decrease the information transfer rate of BCI. In this paper, a P300 BCI using a 7 × 12 matrix explored new flash patterns (16-, 18- and 21-flash pattern) with different TTIs to assess the effects of TTI on P300 BCI performance. The new flash patterns were designed to minimize TTI, decrease repetition blindness, and examine the temporal relationship between each flash of a given stimulus by placing a minimum of one (16-flash pattern), two (18-flash pattern), or three (21-flash pattern) non-target flashes between each target flashes. Online results showed that the 16-flash pattern yielded the lowest classification accuracy among the three patterns. The results also showed that the 18-flash pattern provides a significantly higher information transfer rate (ITR) than the 21-flash pattern; both patterns provide high ITR and high accuracy for all subjects. PMID:22350331

Microscopic diffusion in hydrated encysted eggs of brine shrimp

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mamontov, Eugene

We have studied microscopic diffusion of water in fully hydrated encysted eggs of brine shrimp (Artemia). We utilized quasielastic neutron scattering. Dry eggs of brine shrimp were rehydrated using (1) water without additives, (2) eutectic mixture of water and dimethyl sulfoxide, and (3) a concentrated aqueous solution of lithium chloride. Despite the complexity of the hydrated multicellular organism, measurable microscopic diffusivity of water is rather well defined. Pure hydration water in eggs exhibits freezing temperature depression, whereas hydration water in eggs mixed with dimethyl sulfoxide or lithium chloride does not crystallize at all. The characteristic size of the voids occupiedmore » by water or aqueous solvents in hydrated brine shrimp eggs is between 2 and 10 nm. Those voids are accessible to co-solvents such as dimethyl sulfoxide and lithium chloride. There is no evidence of intracellular water in the hydrated eggs. The lack of intracellular water in the fully hydrated (but still under arrested development) state must be linked to the unique resilience against adverse environmental factors documented not only for the anhydrous, but also hydrated encysted eggs of brine shrimp.« less

Exchange of Laptev Sea and Arctic Ocean halocline waters in response to atmospheric forcing

NASA Astrophysics Data System (ADS)

Bauch, D.; Dmitrenko, I. A.; Wegner, C.; HöLemann, J.; Kirillov, S. A.; Timokhov, L. A.; Kassens, H.

2009-05-01

Combined δ18O/salinity data reveal a distinctive water mass generated during winter sea ice formation which is found predominantly in the coastal polynya region of the southern Laptev Sea. Export of the brine-enriched bottom water shows interannual variability in correlation with atmospheric conditions. Summer anticyclonic circulation is favoring an offshore transport of river water at the surface as well as a pronounced signal of brine-enriched waters at about 50 m water depth at the shelf break. Summer cyclonic atmospheric circulation favors onshore or an eastward, alongshore water transport, and at the shelf break the river water fraction is reduced and the pronounced brine signal is missing, while on the middle Laptev Sea shelf, brine-enriched waters are found in high proportions. Residence times of bottom and subsurface waters on the shelf may thereby vary considerably: an export of shelf waters to the Arctic Ocean halocline might be shut down or strongly reduced during "onshore" cyclonic atmospheric circulation, while with "offshore" anticyclonic atmospheric circulation, brine waters are exported and residence times may be as short as 1 year only.

A field test of electromagnetic geophysical techniques for locating simulated in situ mining leach solution

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tweeton, D.R.; Hanson, J.C.; Friedel, M.J.

1994-01-01

The US Bureau of Mines, The University of Arizona, Sandia National Laboratories, and Zonge Engineering and Research Organization, Inc., conducted cooperative field tests of six electromagnetic (EM) geophysical methods to compare their effectiveness in locating a brine solution simulating in situ leach solution or a high-conductivity plume of contamination. The brine was approximately 160 m below the surface. The testsite was the University's San Xavier experimental mine near Tucson, AZ. Geophysical surveys using surface and surface-borehole, time-domain electromagnetic (TEM) induction; surface controlled-source audiofrequency magnetotellurics (CSAMT); surface-borehole, frequency-domain electromagnetic (FEM) induction; crosshole FEM; and surface magnetic field ellipticity were conducted beforemore » and during brine injection. The surface TEM data showed a broad decrease in resistivity. CSAMT measurements with the conventional orientation did not detect the brine, but measurements with another orientation indicated some decrease in resistivity. The surface-borehole and crosshole methods located a known fracture and other fracture zones inferred from borehole induction logs. Surface magnetic field ellipticity data showed a broad decrease in resistivity at depth following brine injection.« less

Formation and Persistence of Brine on Mars: Experimental Simulations throughout the Diurnal Cycle at the Phoenix Landing Site

NASA Astrophysics Data System (ADS)

Fischer, E.; Martínez, G. M.; Rennó, N. O.

2016-12-01

In the last few years, water ice and salts capable of melting this ice and producing liquid saline water (brine) have been detected on Mars. Moreover, indirect evidence for brine has been found in multiple areas of the planet. Here, we simulate full diurnal cycles of temperature and atmospheric water vapor content at the Phoenix landing site for the first time and show experimentally that, in spite of the low Mars-like chamber temperature, brine forms minutes after the ground temperature exceeds the eutectic temperature of salts in contact with water ice. Moreover, we show that the brine stays liquid for most of the diurnal cycle when enough water ice is available to compensate for evaporation. This is predicted to occur seasonally in areas of the polar region where the temperature exceeds the eutectic value and frost or snow is deposited on saline soils, or where water ice and salts coexist in the shallow subsurface. This is important because the existence of liquid water is a key requirement for habitability.

The fate of minor alkali elements in the chemical evolution of salt lakes

PubMed Central

2011-01-01

Alkaline earth elements and alkali metals (Mg, Ca, Na and K) play an important role in the geochemical evolution of saline lakes as the final brine type is defined by the abundance of these elements. The role of major ions in brine evolution has been studied in great detail, but little has been done to investigate the behaviour of minor alkali elements in these systems despite their similar chemical affinities to the major cations. We have examined three major anionic brine types, chloride, sulphate, and bicarbonate-carbonate, in fifteen lakes in North America and Antarctica to determine the geochemical behaviour of lithium, rubidium, strontium, and barium. Lithium and rubidium are largely conservative in all water types, and their concentrations are the result of long-term solute input and concentration through evaporation and/or sublimation. Strontium and barium behaviours vary with anionic brine type. Strontium can be removed in sulphate and carbonate-rich lakes by the precipitation of carbonate minerals. Barium may be removed in chloride and sulphate brines by either the precipitation of barite and perhaps biological uptake. PMID:21992434

Synthesis and formation mechanism of pinnoite in sulfated-type boron concentrated brine by dilution method

NASA Astrophysics Data System (ADS)

Peng, Jiaoyu; Bian, Shaoju; Lin, Feng; Wang, Liping; Dong, Yaping; Li, Wu

2017-10-01

The synthesis of pinnoite (MgB2O(OH)6) in boron-containing brine was established with a novel dilution method. Effects of temperature, precipitation time, boron concentration and mass dilution ratio on the formation of pinnoite were investigated. The products obtained were characterized by X-ray diffraction (XRD), Raman, thermogravimetric and differential scanning calorimeter (TG-DSC), and scanning electron microscopy. The transformation mechanism of pinnoite with different dilution ratios was assumed by studying the crystal growth of pinnoite. The results showed that pinnoite was synthesized above 60 °C in the diluted brine. There were two reaction steps - precipitation of amorphous solid and the formation of pinnoite crystals - during the whole reaction process of pinnoite when the dilution ratio is more than 1.0 at 80 °C. While in the 0.5 diluted brine, only one reaction step of pinnoite crystal formation was observed and its transformation mechanism was discussed based on dissociation of polyborates in brine. Besides, the origin of pinnoite mineral deposited on salt lake bottom was proposed.

Microscopic diffusion in hydrated encysted eggs of brine shrimp

DOE PAGES

Mamontov, Eugene

2017-05-24

We have studied microscopic diffusion of water in fully hydrated encysted eggs of brine shrimp (Artemia). We utilized quasielastic neutron scattering. Dry eggs of brine shrimp were rehydrated using (1) water without additives, (2) eutectic mixture of water and dimethyl sulfoxide, and (3) a concentrated aqueous solution of lithium chloride. Despite the complexity of the hydrated multicellular organism, measurable microscopic diffusivity of water is rather well defined. Pure hydration water in eggs exhibits freezing temperature depression, whereas hydration water in eggs mixed with dimethyl sulfoxide or lithium chloride does not crystallize at all. The characteristic size of the voids occupiedmore » by water or aqueous solvents in hydrated brine shrimp eggs is between 2 and 10 nm. Those voids are accessible to co-solvents such as dimethyl sulfoxide and lithium chloride. There is no evidence of intracellular water in the hydrated eggs. The lack of intracellular water in the fully hydrated (but still under arrested development) state must be linked to the unique resilience against adverse environmental factors documented not only for the anhydrous, but also hydrated encysted eggs of brine shrimp.« less

Formation and character of an ancient 19-m ice cover and underlying trapped brine in an "ice-sealed" east Antarctic lake.

PubMed

Doran, Peter T; Fritsen, Christian H; McKay, Christopher P; Priscu, John C; Adams, Edward E

2003-01-07

Lake Vida, one of the largest lakes in the McMurdo Dry Valleys of Antarctica, was previously believed to be shallow (<10 m) and frozen to its bed year-round. New ice-core analysis and temperature data show that beneath 19 m of ice is a water column composed of a NaCl brine with a salinity seven times that of seawater that remains liquid below -10 degrees C. The ice cover thickens at both its base and surface, sealing concentrated brine beneath. The ice cover is stabilized by a negative feedback between ice growth and the freezing-point depression of the brine. The ice cover contains frozen microbial mats throughout that are viable after thawing and has a history that extends to at least 2,800 (14)C years B.P., suggesting that the brine has been isolated from the atmosphere for as long. To our knowledge, Lake Vida has the thickest subaerial lake ice cover recorded and may represent a previously undiscovered end-member lacustrine ecosystem on Earth.

Formation and character of an ancient 19-m ice cover and underlying trapped brine in an “ice-sealed” east Antarctic lake

PubMed Central

Doran, Peter T.; Fritsen, Christian H.; McKay, Christopher P.; Priscu, John C.; Adams, Edward E.

2003-01-01

Lake Vida, one of the largest lakes in the McMurdo Dry Valleys of Antarctica, was previously believed to be shallow (<10 m) and frozen to its bed year-round. New ice-core analysis and temperature data show that beneath 19 m of ice is a water column composed of a NaCl brine with a salinity seven times that of seawater that remains liquid below −10°C. The ice cover thickens at both its base and surface, sealing concentrated brine beneath. The ice cover is stabilized by a negative feedback between ice growth and the freezing-point depression of the brine. The ice cover contains frozen microbial mats throughout that are viable after thawing and has a history that extends to at least 2,800 14C years B.P., suggesting that the brine has been isolated from the atmosphere for as long. To our knowledge, Lake Vida has the thickest subaerial lake ice cover recorded and may represent a previously undiscovered end-member lacustrine ecosystem on Earth. PMID:12518052

Modeling the morphogenesis of brine channels in sea ice.

PubMed

Kutschan, B; Morawetz, K; Gemming, S

2010-03-01

Brine channels are formed in sea ice under certain constraints and represent a habitat of different microorganisms. The complex system depends on a number of various quantities as salinity, density, pH value, or temperature. Each quantity governs the process of brine channel formation. There exists a strong link between bulk salinity and the presence of brine drainage channels in growing ice with respect to both the horizontal and vertical planes. We develop a suitable phenomenological model for the formation of brine channels both referring to the Ginzburg-Landau theory of phase transitions as well as to the chemical basis of morphogenesis according to Turing. It is possible to conclude from the critical wave number on the size of the structure and the critical parameters. The theoretically deduced transition rates have the same magnitude as the experimental values. The model creates channels of similar size as observed experimentally. An extension of the model toward channels with different sizes is possible. The microstructure of ice determines the albedo feedback and plays therefore an important role for large-scale global circulation models.

Uranium (VI) solubility in carbonate-free ERDA-6 brine

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lucchini, Jean-francois; Khaing, Hnin; Reed, Donald T

2010-01-01

When present, uranium is usually an element of importance in a nuclear waste repository. In the Waste Isolation Pilot Plant (WIPP), uranium is the most prevalent actinide component by mass, with about 647 metric tons to be placed in the repository. Therefore, the chemistry of uranium, and especially its solubility in the WIPP conditions, needs to be well determined. Long-term experiments were performed to measure the solubility of uranium (VI) in carbonate-free ERDA-6 brine, a simulated WIPP brine, at pC{sub H+} values between 8 and 12.5. These data, obtained from the over-saturation approach, were the first repository-relevant data for themore » VI actinide oxidation state. The solubility trends observed pointed towards low uranium solubility in WIPP brines and a lack of amphotericity. At the expected pC{sub H+} in the WIPP ({approx} 9.5), measured uranium solubility approached 10{sup -7} M. The objective of these experiments was to establish a baseline solubility to further investigate the effects of carbonate complexation on uranium solubility in WIPP brines.« less

Spatial-temporal characteristics of lightning flash size in a supercell storm

NASA Astrophysics Data System (ADS)

Zhang, Zhixiao; Zheng, Dong; Zhang, Yijun; Lu, Gaopeng

2017-11-01

The flash sizes of a supercell storm, in New Mexico on October 5, 2004, are studied using the observations from the New Mexico Lightning Mapping Array and the Albuquerque, New Mexico, Doppler radar (KABX). First, during the temporal evolution of the supercell, the mean flash size is anti-correlated with the flash rate, following a unary power function, with a correlation coefficient of - 0.87. In addition, the mean flash size is linearly correlated with the area of reflectivity > 30 dBZ at 5 km normalized by the flash rate, with a correlation coefficient of 0.88. Second, in the horizontal, flash size increases along the direction from the region near the convection zone to the adjacent forward anvil. The region of minimum flash size usually corresponds to the region of maximum flash initiation and extent density. The horizontal correspondence between the mean flash size and the flash extent density can also be fitted by a unary power function, and the correlation coefficient is > 0.5 in 50% of the radar volume scans. Furthermore, the quality of fit is positively correlated to the convective intensity. Third, in the vertical direction, the height of the maximum flash initiation density is close to the height of maximum flash extent density, but corresponds to the height where the mean flash size is relatively small. In the discussion, the distribution of the small and dense charge regions when and where convection is vigorous in the storm, is deduced to be responsible for the relationship that flash size is temporally and spatially anti-correlated with flash rate and density, and the convective intensity.

Flash memory management system and method utilizing multiple block list windows

NASA Technical Reports Server (NTRS)

Chow, James (Inventor); Gender, Thomas K. (Inventor)

2005-01-01

The present invention provides a flash memory management system and method with increased performance. The flash memory management system provides the ability to efficiently manage and allocate flash memory use in a way that improves reliability and longevity, while maintaining good performance levels. The flash memory management system includes a free block mechanism, a disk maintenance mechanism, and a bad block detection mechanism. The free block mechanism provides efficient sorting of free blocks to facilitate selecting low use blocks for writing. The disk maintenance mechanism provides for the ability to efficiently clean flash memory blocks during processor idle times. The bad block detection mechanism provides the ability to better detect when a block of flash memory is likely to go bad. The flash status mechanism stores information in fast access memory that describes the content and status of the data in the flash disk. The new bank detection mechanism provides the ability to automatically detect when new banks of flash memory are added to the system. Together, these mechanisms provide a flash memory management system that can improve the operational efficiency of systems that utilize flash memory.

Development of a Direct Contact Heat Exchanger, Phase 1 Study Report

NASA Technical Reports Server (NTRS)

Manvi, R.

1978-01-01

Electric power generation from geothermal brine requires, first, bringing the hot brine to the surface and then converting the heat to electric power. Binary conversion schemes were proposed, with the heat transfer between the brine and the working organic fluid taking place in a conventional tube and shell heat exchanger. If the brine is heavily laden with dissolved solids, however, solids buildup on the heat exchanger surfaces leads to a considerable degree of fouling and an accompanying drop in performance is experienced. A possible solution to this problem is the use of a direct contact exchanger with the secondary fluid power cycle. The proposed concept involves the formation of fluid sheets and bells as heat angles. Results of a study concerning the fluid mechanics of such surfaces are given.

Cement/caprock fracture healing experiments to assess the integrity of CO2 injection wells

NASA Astrophysics Data System (ADS)

Du Frane, W. L.; Mason, H. E.; Walsh, S. D.; Ruddle, D. G.; Carroll, S.

2012-12-01

It has been speculated that fractures along wellbore cement/caprock interfaces may provide a path for release of carbon from both long-term sequestration-sites and CO2-based enhanced oil recovery operations. The goal of this study is to evaluate the potential for fracture growth and healing in the wellbore environment, and its impact on wellbore permeability. A series of flow-through experiments was conducted, in which sample cores containing a planar fracture between impermeable caprock (compacted quartz, from 13,927' depth in Kern County) and cement (Portland G cured by ATSM standards) were reacted with brine containing variable amounts of carbonic acid (pCO2 between 0 and 3 MPa). The initial fracture geometry was controlled by grinding the caprock and cement pieces flat, and then bead blasting topography into the cement surfaces. Runs lasted 4-8 days with cores and brine maintained at constant temperature (60 °C). Constant confining pressure (24.8 MPa) was applied to cores, while brine was flowed with constant rates (0.05-0.10 mL/min) and pore pressure (12.4 MPa). Geomechanical and geochemical responses of the fractures were monitored by in situ measurements of differential pressure, and by periodically sampling output brine to analyze compositional changes. In every experiment the total permeability of samples cores decreased substantially. For runs using brine with pCO2 = 3 MPa, sample permeability continually decreased by over a factor of 200. Sample permeability also decreased by a factor of 50 having stabilized after ~3 days in a run using brine without CO2 (pCO2 = 0 MPa). These reductions in permeability appear to be the result of chemically-induced changes to the mechanical properties of the cement surface. Prior to reaction, the cement-caprock samples had high strength and elastic response to changes in stress during loading. After the experiments, the samples were weaker, and showed inelastic response to changes in stress during unloading. All cement surfaces exposed to CO2-rich brine were heavily reacted, as evidenced by coatings of rust-colored amorphous material. X-ray micro-tomography images revealed a series of reaction zones consistent with the results of related experiments by other researchers [e.g. Kutchko et al. 2007]. The mechanical properties of the individual reaction zones were evaluated by nano-indentation. Sampling during runs indicated that brine with pCO2 = 3 MPa became substantially enriched in Ca, Si, and Al, whereas composition of output brine with pCO2 = 0 MPa had little change over the run duration. The enrichment of Al in the brine with pCO2 = 3 MPa indicates that both Al -bearing minerals and amorphous calcium-silicate-hydrate (CSH) dissolved from the cement. Geochemical reaction pathways were further characterized in the reacted zones with the cement by scanning electron microscope, x-ray diffraction, and solid state NMR spectroscopy. These results suggest that the evolution of fractures in our experiments are determined by 3 competing factors: 1) swelling of CSH through hydration from the brine, 2) dissolution of cement into brine containing CO2, and 3) mechanical weakening of cement by chemical reaction with CO2. This work was performed under the auspices of the U.S. Department of Energy by Lawrence Livermore National Laboratory under Contract W-7405-Eng-48 and Contract DE-AC52-07NA27344.

Perceived control and hot flashes in treatment-seeking breast cancer survivors and menopausal women.

PubMed

Carpenter, Janet S; Wu, Jingwei; Burns, Debra S; Yu, Menggang

2012-01-01

Lower perceived control over hot flashes has been linked to fewer coping strategies, more catastrophizing, and greater hot flash severity and distress in midlife women, yet this important concept has not yet been studied in breast cancer survivors. The aim of this study was to explore perceived control over hot flashes and hot flashes in breast cancer survivors compared with midlife women without cancer. Ninety-nine survivors and 138 midlife women completed questionnaires and a prospective, electronic hot flash diary. All data were collected at a baseline assessment before randomization in a behavioral intervention study. Both groups had moderate perceived control over hot flashes. Control was not significantly related to hot flash frequency but was significantly related to hot flash severity, bother, and interference in both groups. A significantly stronger association between control and hot flash interference was found for survivors than for midlife women. Survivors using hot flash treatments perceived less control than did survivors not using hot flash treatments, whereas the opposite was true in midlife women. Findings extend our knowledge of perceived control over hot flashes in both survivors and midlife women. Findings emphasize the importance of continued menopausal symptom assessment and management, support the importance of continuing nursing care even for survivors who are already using hot flash treatment, and suggest that nursing interventions aimed at improving perceived control over hot flashes may be more helpful for survivors than for midlife women.

Synoptic-scale atmospheric conditions associated with flash flooding in watersheds of the Catskill Mountains, New York, USA

NASA Astrophysics Data System (ADS)

Teale, N. G.; Quiring, S. M.

2015-12-01

Understanding flash flooding is important in unfiltered watersheds, such as portions of the New York City water supply system (NYCWSS), as water quality is degraded by turbidity associated with flooding. To further understand flash flooding in watersheds of the NYCWSS, synoptic-scale atmospheric conditions most frequently associated with flash flooding between 1987 and 2013 were examined. Flash floods were identified during this time period using USGS 15-minute discharge data at the Esopus Creek near Allaben, NY and Neversink River at Claryville, NY gauges. Overall, 25 flash floods were detected, occurring over 17 separate flash flood days. These flash flood days were compared to the days on which flash flood warnings encompassing the study area was issued by the National Weather Service. The success rate for which the flash flood warnings for Ulster County coincided with flash flood in the study watershed was 0.09, demonstrating the highly localized nature of flash flooding in the Catskill Mountain region. The synoptic-scale atmospheric patterns influencing the study area were characterized by a principal component analysis and k-means clustering of NCEP/NCAR 500 mb geopotential height reanalysis data. This procedure was executed in Spatial Synoptic Typer Tools 4.0. While 17 unique synoptic patterns were identified, only 3 types were strongly associated with flash flooding events. A strong southwesterly flow suggesting advection of moisture from the Atlantic Ocean and Gulf of Mexico is shown in composites of these 3 types. This multiscalar study thereby links flash flooding in the NYCWSS with synoptic-scale atmospheric circulation.Understanding flash flooding is important in unfiltered watersheds, such as portions of the New York City water supply system (NYCWSS), as water quality is degraded by turbidity associated with flooding. To further understand flash flooding in watersheds of the NYCWSS, synoptic-scale atmospheric conditions most frequently associated with flash flooding between 1987 and 2013 were examined. Flash floods were identified during this time period using USGS 15-minute discharge data at the Esopus Creek near Allaben, NY and Neversink River at Claryville, NY gauges. Overall, 25 flash floods were detected, occurring over 17 separate flash flood days. These flash flood days were compared to the days on which flash flood warnings encompassing the study area was issued by the National Weather Service. The success rate for which the flash flood warnings for Ulster County coincided with flash flood in the study watershed was 0.09, demonstrating the highly localized nature of flash flooding in the Catskill Mountain region. The synoptic-scale atmospheric patterns influencing the study area were characterized by a principal component analysis and k-means clustering of NCEP/NCAR 500 mb geopotential height reanalysis data. This procedure was executed in Spatial Synoptic Typer Tools 4.0. While 17 unique synoptic patterns were identified, only 3 types were strongly associated with flash flooding events. A strong southwesterly flow suggesting advection of moisture from the Atlantic Ocean and Gulf of Mexico is shown in composites of these 3 types. This multiscalar study thereby links flash flooding in the NYCWSS with synoptic-scale atmospheric circulation.

CO2-brine-mineral Reactions in Geological Carbon Storage: Results from an EOR Experiment

NASA Astrophysics Data System (ADS)

Chapman, H.; Wigley, M.; Bickle, M.; Kampman, N.; Dubacq, B.; Galy, A.; Ballentine, C.; Zhou, Z.

2012-04-01

Dissolution of CO2 in brines and reactions of the acid brines ultimately dissolving silicate minerals and precipitating carbonate minerals are the prime long-term mechanisms for stabilising the light supercritical CO2 in geological carbon storage. However the rates of dissolution are very uncertain as they are likely to depend on the heterogeneity of the flow of CO2, the possibility of convective instability of the denser CO2-saturated brines and on fluid-mineral reactions which buffer brine acidity. We report the results of sampling brines and gases during a phase of CO2 injection for enhanced oil recovery in a small oil field. Brines and gases were sampled at production wells daily for 3 months after initiation of CO2 injection and again for two weeks after 5 months. Noble gas isotopic spikes were detected at producing wells within days of initial CO2 injection but signals continued for weeks, and at some producers for the duration of the sampling period, attesting to the complexity of gas-species pathways. Interpretations are complicated by the previous history of the oil field and re-injection of produced water prior to injection of CO2. However water sampled from some producing wells during the phase of CO2 injection showed monotonic increases in alkalinity and in concentrations of major cations to levels in excess of those in the injected water. The marked increase in Na, and smaller increases in Ca, Mg, Si, K and Sr are interpreted primarily to result from silicate dissolution as the lack of increase in S and Cl concentrations preclude additions of more saline waters. Early calcite dissolution was followed by re-precipitation. 87Sr/86Sr ratios in the waters apparently exceed the 87Sr/86Sr ratios of acetic and hydrochloric acid leaches of carbonate fractions of the reservoir rocks and the silicate residues from the leaching. This may indicate incongruent dissolution of Sr or larger scale isotopic heterogeneity of the reservoir. This is being investigated further by analyses of rock and mineral clasts from core. A surprising result of this study is the extent to which CO2 has dissolved in brines to drive fluid-rock reactions during the short duration of this experiment. However, simple one-dimensional flow modelling with lateral diffusion of CO2 into brines demonstrates that the natural heterogeneities in permeability in the reservoir on the scale of ~ 1 m are sufficient to cause extensive fingering of the CO2 along the highest permeability horizons. Because flow of brines is fastest in the relatively high permeability layers adjacent to the CO2-bearing layers, production of this more CO2-rich water dominates the output from production wells.

Membrane Cells for Brine Electrolysis.

ERIC Educational Resources Information Center

Tingle, M.

1982-01-01

Membrane cells were developed as alternatives to mercury and diaphragm cells for the electrolysis of brine. Compares the three types of cells, focusing on the advantages and disadvantages of membrane cells. (JN)

Hot Flashes and Quality of Life Among Breast Cancer Patients

DTIC Science & Technology

2006-08-01

hot flashes, 40.7% report at baseline, having used HRT and 26.8% used exercise to control hot flashes. The 12-month data indicates that 26.5% of the...entire sample who are experiencing hot flashes, tried or are using some form of HRT to control hot flashes with exercise still the most frequently...used approach to manage hot flashes with 44.2% of sample currently exercising . 15. SUBJECT TERMS Breast Cancer, Hot Flashes, Quality of Life

Space and Industrial Brine Drying Technologies

NASA Technical Reports Server (NTRS)

Jones, Harry W.; Wisniewski, Richard S.; Flynn, Michael; Shaw, Hali

2014-01-01

This survey describes brine drying technologies that have been developed for use in space and industry. NASA has long considered developing a brine drying system for the International Space Station (ISS). Possible processes include conduction drying in many forms, spray drying, distillation, freezing and freeze drying, membrane filtration, and electrical processes. Commercial processes use similar technologies. Some proposed space systems combine several approaches. The current most promising candidates for use on the ISS use either conduction drying with membrane filtration or spray drying.

Physiological characteristics of bacteria isolated from water brines within permafrost

NASA Astrophysics Data System (ADS)

Shcherbakova, V.; Rivkina, E.; Laurinavichuis, K.; Pecheritsina, S.; Gilichinsky, D.

2004-01-01

In the Arctic there are lenses of overcooled water brines (cryopegs) sandwiched within permafrost marine sediments 100 120 thousand years old. We have investigated the physiological properties of the pure cultures of anaerobic Clostridium sp. strain 14D1 and two strains of aerobic bacteria Psychrobacter sp. isolated from these cryopegs. The structural and physiological characteristics of new bacteria from water brines have shown their ability to survive and develop under harsh conditions, such as subzero temperatures and high salinity.

Portable brine evaporator unit, process, and system

DOEpatents

Hart, Paul John; Miller, Bruce G.; Wincek, Ronald T.; Decker, Glenn E.; Johnson, David K.

2009-04-07

The present invention discloses a comprehensive, efficient, and cost effective portable evaporator unit, method, and system for the treatment of brine. The evaporator unit, method, and system require a pretreatment process that removes heavy metals, crude oil, and other contaminates in preparation for the evaporator unit. The pretreatment and the evaporator unit, method, and system process metals and brine at the site where they are generated (the well site). Thus, saving significant money to producers who can avoid present and future increases in transportation costs.

Durability of high performance concrete in magnesium brine

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tumidajski, P.J.; Chan, G.W.

1996-04-01

The durability of six concretes exposed to magnesium brine was monitored for 24 months. These concretes incorporated ground granulated blast furnace slag, silica fume, and fly ash. The Young`s moduli, chloride penetrations, and median pore diameters were measured. There was a cyclic nature to these properties due to the complicated interaction of hydration with magnesium, chloride and sulfate attack. Mineral admixtures, in combination with a long initial cure, provided the most durable concrete. Concrete with 65% slag had the best overall durability to the brines tested.

Physiologically assessed hot flashes and endothelial function among midlife women.

PubMed

Thurston, Rebecca C; Chang, Yuefang; Barinas-Mitchell, Emma; Jennings, J Richard; von Känel, Roland; Landsittel, Doug P; Matthews, Karen A

2017-08-01

Hot flashes are experienced by most midlife women. Emerging data indicate that they may be associated with endothelial dysfunction. No studies have tested whether hot flashes are associated with endothelial function using physiologic measures of hot flashes. We tested whether physiologically assessed hot flashes were associated with poorer endothelial function. We also considered whether age modified associations. Two hundred seventy-two nonsmoking women reporting either daily hot flashes or no hot flashes, aged 40 to 60 years, and free of clinical cardiovascular disease, underwent ambulatory physiologic hot flash and diary hot flash monitoring; a blood draw; and ultrasound measurement of brachial artery flow-mediated dilation to assess endothelial function. Associations between hot flashes and flow-mediated dilation were tested in linear regression models controlling for lumen diameter, demographics, cardiovascular disease risk factors, and estradiol. In multivariable models incorporating cardiovascular disease risk factors, significant interactions by age (P < 0.05) indicated that among the younger tertile of women in the sample (age 40-53 years), the presence of hot flashes (beta [standard error] = -2.07 [0.79], P = 0.01), and more frequent physiologic hot flashes (for each hot flash: beta [standard error] = -0.10 [0.05], P = 0.03, multivariable) were associated with lower flow-mediated dilation. Associations were not accounted for by estradiol. Associations were not observed among the older women (age 54-60 years) or for self-reported hot flash frequency, severity, or bother. Among the younger women, hot flashes explained more variance in flow-mediated dilation than standard cardiovascular disease risk factors or estradiol. Among younger midlife women, frequent hot flashes were associated with poorer endothelial function and may provide information about women's vascular status beyond cardiovascular disease risk factors and estradiol.

Menopausal Hot Flashes and Carotid Intima Media Thickness Among Midlife Women.

PubMed

Thurston, Rebecca C; Chang, Yuefang; Barinas-Mitchell, Emma; Jennings, J Richard; Landsittel, Doug P; Santoro, Nanette; von Känel, Roland; Matthews, Karen A

2016-12-01

There has been a longstanding interest in the role of menopause and its correlates in the development of cardiovascular disease (CVD) in women. Menopausal hot flashes are experienced by most midlife women; emerging data link hot flashes to CVD risk indicators. We tested whether hot flashes, measured via state-of-the-art physiologic methods, were associated with greater subclinical atherosclerosis as assessed by carotid ultrasound. We considered the role of CVD risk factors and estradiol concentrations in these associations. A total of 295 nonsmoking women free of clinical CVD underwent ambulatory physiologic hot flash assessments; a blood draw; and carotid ultrasound measurement of intima media thickness and plaque. Associations between hot flashes and subclinical atherosclerosis were tested in regression models controlling for CVD risk factors and estradiol. More frequent physiologic hot flashes were associated with higher carotid intima media thickness (for each additional hot flash: β [SE]=0.004 [0.001]; P=0.0001; reported hot flash: β [SE]=0.008 [0.002]; P=0.002, multivariable) and plaque (eg, for each additional hot flash, odds ratio [95% confidence interval] plaque index ≥2=1.07 [1.003-1.14]; P=0.04, relative to no plaque, multivariable] among women reporting daily hot flashes; associations were not accounted for by CVD risk factors or by estradiol. Among women reporting hot flashes, hot flashes accounted for more variance in intima media thickness than most CVD risk factors. Among women reporting daily hot flashes, frequent hot flashes may provide information about a woman's vascular status beyond standard CVD risk factors and estradiol. Frequent hot flashes may mark a vulnerable vascular phenotype among midlife women. © 2016 American Heart Association, Inc.

Menopausal Hot Flashes and Carotid Intima Media Thickness among Midlife Women

PubMed Central

Thurston, Rebecca C.; Chang, Yuefang; Barinas-Mitchell, Emma; Jennings, J. Richard; Landsittel, Doug P.; Santoro, Nanette; von Känel, Roland; Matthews, Karen A.

2016-01-01

Background and Purpose There has been a longstanding interest in the role of menopause and its correlates in the development of cardiovascular disease (CVD) in women. Menopausal hot flashes are experienced by most midlife women; emerging data link hot flashes to CVD risk indicators. We tested whether hot flashes, measured via state-of-the-art physiologic methods, were associated with greater subclinical atherosclerosis as assessed by carotid ultrasound. We considered the role of CVD risk factors and estradiol concentrations in these associations. Methods 295 nonsmoking women free of clinical CVD underwent ambulatory physiologic hot flash assessments; a blood draw; and carotid ultrasound measurement of IMT and plaque. Associations between hot flashes and subclinical atherosclerosis were tested in regression models controlling for CVD risk factors and estradiol. Results More frequent physiologic hot flashes were associated with higher carotid intima media thickness [IMT; for each additional hot flash: beta (standard error)=.004(.001), p=.0001; reported hot flash: beta (standard error)=.008(.002), p=.002, multivariable] and plaque [e.g., for each additional hot flash, odds ratio (95% confidence interval) plaque index ≥2=1.07(1.003–1.14, p=.04), relative to no plaque, multivariable] among women reporting daily hot flashes; associations were not accounted for by CVD risk factors or by estradiol. Among women reporting hot flashes, hot flashes accounted for more variance in IMT than most CVD risk factors. Conclusions Among women reporting daily hot flashes, frequent hot flashes may provide information about a woman’s vascular status beyond standard CVD risk factors and estradiol. Frequent hot flashes may mark a vulnerable vascular phenotype among midlife women. PMID:27834746

Behavioral Weight Loss for the Management of Menopausal Hot Flashes: A Pilot Study

PubMed Central

Thurston, Rebecca C.; Ewing, Linda J.; Low, Carissa A.; Christie, Aimee J.; Levine, Michele D.

2014-01-01

Objective Although adiposity has been considered protective against hot flashes, newer data suggest positive relations between flashes and adiposity. No studies have been specifically designed to test whether weight loss reduces hot flashes. This pilot study aimed to evaluate the feasibility, acceptability, and initial efficacy of behavioral weight loss to reduce hot flashes. Methods Forty overweight/obese women with hot flashes (≥4/day) were randomized to a behavioral weight loss intervention or to wait list control. Hot flashes were assessed pre- and post-intervention via physiologic monitor, diary, and questionnaire. Comparisons of changes in hot flashes and anthropometrics between conditions were tested via Wilcoxon tests. Results Study retention (83%) and intervention satisfaction (93.8%) were high. Most women (74.1%) reported that hot flash reduction was a main motivator to lose weight. Women randomized to the weight loss intervention lost more weight (-8.86 kg) than did women randomized to control (+0.23 kg, p<.0001). Women randomized to weight loss also showed greater reductions in questionnaire-reported hot flashes (2-week hot flashes: −63.0) than did women in the control (−28.0, p=.03), a difference not demonstrated in other hot flash measures. Reductions in weight and hot flashes were significantly correlated (e.g., r=.47, p=.006). Conclusions This pilot study showed a behavioral weight loss program to be feasible, acceptable, and effective in producing weight loss among overweight/obese women with hot flashes. Findings indicate the importance of a larger study designed to test behavioral weight loss for hot flash reduction. Hot flash management could motivate women to engage in this health-promoting behavior. PMID:24977456

Karst flash floods: an example from the Dinaric karst (Croatia)

NASA Astrophysics Data System (ADS)

Bonacci, O.; Ljubenkov, I.; Roje-Bonacci, T.

2006-03-01

Flash floods constitute one of the deadliest and costliest natural disasters worldwide. This paper explains the karst flash flood phenomenon, which represents a special kind of flash flood. As the majority of flash floods karst flash floods are caused by intensive short-term precipitation in an area whose surface rarely exceeds a few square kilometres. The characteristics of all flash floods are their short duration, small areal extent, high flood peaks and rapid flows, and heavy loss of life and property. Karst flash floods have specific characteristics due to special conditions for water circulation, which exist in karst terrains. During karst flash floods a sudden rise of groundwater levels occurs, which causes the appearance of numerous, unexpected, abundant and temporary karst springs. This paper presents in detail an example of a karst flash flood in the Marina bay (Dinaric karst region of Croatia), which occurred in December 2004.

A Comprehensive Study on Energy Efficiency and Performance of Flash-based SSD

DOE Office of Scientific and Technical Information (OSTI.GOV)

Park, Seon-Yeon; Kim, Youngjae; Urgaonkar, Bhuvan

2011-01-01

Use of flash memory as a storage medium is becoming popular in diverse computing environments. However, because of differences in interface, flash memory requires a hard-disk-emulation layer, called FTL (flash translation layer). Although the FTL enables flash memory storages to replace conventional hard disks, it induces significant computational and space overhead. Despite the low power consumption of flash memory, this overhead leads to significant power consumption in an overall storage system. In this paper, we analyze the characteristics of flash-based storage devices from the viewpoint of power consumption and energy efficiency by using various methodologies. First, we utilize simulation tomore » investigate the interior operation of flash-based storage of flash-based storages. Subsequently, we measure the performance and energy efficiency of commodity flash-based SSDs by using microbenchmarks to identify the block-device level characteristics and macrobenchmarks to reveal their filesystem level characteristics.« less

Multi- and unisensory visual flash illusions.

PubMed

Courtney, Jon R; Motes, Michael A; Hubbard, Timothy L

2007-01-01

The role of stimulus structure in multisensory and unisensory interactions was examined. When a flash (17 ms) was accompanied by multiple tones (each 7 ms, SOA < or =100 ms) multiple flashes were reported, and this effect has been suggested to reflect the role of stimulus continuity in multisensory interactions. In experiments 1 and 2 we examined if stimulus continuity would affect concurrently presented stimuli. When a relatively longer flash (317 ms) was accompanied by multiple tones (each 7 ms), observers reported perceiving multiple flashes. In experiment 3 we tested whether a flash presented near fixation would induce an illusory flash further in the periphery. One flash (17 ms) presented 5 degrees below fixation was reported as multiple flashes if presented with two flashes (each 17 ms, SOA =100 ms) 2 degrees above fixation. The extent to which these data support a phenomenological continuity principle and whether this principle applies to unisensory perception is discussed.

Interactions of numerical and temporal stimulus characteristics on the control of response location by brief flashes of light.

PubMed

Fetterman, J Gregor; Killeen, P Richard

2011-09-01

Pigeons pecked on three keys, responses to one of which could be reinforced after 3 flashes of the houselight, to a second key after 6, and to a third key after 12. The flashes were arranged according to variable-interval schedules. Response allocation among the keys was a function of the number of flashes. When flashes were omitted, transitions occurred very late. Increasing flash duration produced a leftward shift in the transitions along a number axis. Increasing reinforcement probability produced a leftward shift, and decreasing reinforcement probability produced a rightward shift. Intermixing different flash rates within sessions separated allocations: Faster flash rates shifted the functions sooner in real time, but later in terms of flash count, and conversely for slower flash rates. A model of control by fading memories of number and time was proposed.

Flash fire propensity of materials

NASA Technical Reports Server (NTRS)

Hilado, C. J.; Cumming, H. J.

1977-01-01

Flash fire test results on 86 materials, evaluated using the USF flash fire screening test, are presented. The materials which appear least prone to flash fires are PVC, polyphenylene oxide and sulfide, and polyether and polyaryl sulfone; these did not produce flash fires under these particular test conditions. The principal value of these screening tests at the present time is in identifying materials which appear prone to flash fires, and in identifying which formulations of a generic material are more or less prone to flash fires.

Hot flash report and measurement among Bangladeshi migrants, their London neighbors, and their community of origin.

PubMed

Sievert, L L; Begum, K; Sharmeen, T; Murphy, L; Whitcomb, B W; Chowdhury, O; Muttukrishna, S; Bentley, G R

2016-12-01

To examine hot flashes in relation to climate and activity patterns, and to compare subjective and objective hot flashes among Bangladeshi immigrants to London, their white London neighbors, and women still living in their community of origin, Sylhet, Bangladesh ("sedentees"). Ninety-five women, aged 40-55, wore the Biolog ambulatory hot flash monitor. Objective measurements and subjective hot flash reports were examined in relation to demographic, reproductive, anthropometric, and lifestyle variables; temperature and humidity at 12:00 and 18:00; and time spent on housework and cooking. Concordance of objective and subjective hot flashes was assessed by Kappa statistics and by sensitivity of hot flash classification. During the study period, Bangladeshi sedentees reported more subjective hot flashes (p < .05), but there was no difference in number of objective hot flashes. White Londoners were more likely to describe hot flashes on their face and neck compared to Bangladeshis (p < .05). Sedentees were more likely to describe hot flashes on their feet (p < .05). Postmenopausal status, increasing parity, and high levels of housework were significant determinants of subjective hot flashes, while ambient temperature and humidity were not. Measures of subjective/objective concordance were low but similar across groups (10-20%). The proportion of objective hot flashes that were also self-reported was lowest among immigrants. Hot flashes were not associated with warmer temperatures, but were associated with housework and with site-specific patterns of cooking. The number of objective hot flash measures did not differ, but differences in subjective experience suggest the influence of culture. © 2016 Wiley Periodicals, Inc.

Phenomenology of the sound-induced flash illusion.

PubMed

Abadi, Richard V; Murphy, Jonathan S

2014-07-01

Past studies, using pairings of auditory tones and visual flashes, which were static and coincident in space but variable in time, demonstrated errors in judging the temporal patterning of the visual flashes-the sound-induced flash illusion. These errors took one of the two forms: under-reporting (sound-induced fusion) or over-reporting (sound-induced fission) of the flash numbers. Our study had three objectives: to examine the robustness of both illusions and to consider the effects of stimulus set and response bias. To this end, we used an extended range of fixed spatial location flash-tone pairings, examined stimuli that were variable in space and time and measured confidence in judging flash numbers. Our results indicated that the sound-induced flash illusion is a robust percept, a finding underpinned by the confidence measures. Sound-induced fusion was found to be more robust than sound-induced fission and a most likely outcome when high numbers of flashes were incorporated within an incongruent flash-tone pairing. Conversely, sound-induced fission was the most likely outcome for the flash-tone pairing which contained two flashes. Fission was also shown to be strongly driven by stimuli confounds such as categorical boundary conditions (e.g. flash-tone pairings with ≤2 flashes) and compressed response options. These findings suggest whilst both fission and fusion are associated with 'auditory driving', the differences in the occurrence and strength of the two illusions not only reflect the separate neuronal mechanisms underlying audio and visual signal processing, but also the test conditions that have been used to investigate the sound-induced flash illusion.

How self-reported hot flashes may relate to affect, cognitive performance and sleep.

PubMed

Regestein, Quentin; Friebely, Joan; Schiff, Isaac

2015-08-01

To explain the controversy about whether midlife women who self-report hot flashes have relatively increased affective symptoms, poor cognitive performance or worse sleep. Retrospective data from 88 women seeking relief from bothersome day and night hot flashes were submitted to mixed linear regression modeling to find if estimated hot flashes, as measured by Women's Health Questionnaire (WHQ) items, or diary-documented hot flashes recorded daily, were associated with each other, or with affective, cognitive or sleep measures. Subjects averaged 6.3 daytime diary-documented hot flashes and 2.4 nighttime diary-documented hot flashes per 24h. Confounder-controlled diary-documented hot flashes but not estimated hot flashes were associated with increased Leeds anxiety scores (F=4.9; t=2.8; p=0.01) and Leeds depression scores (3.4; 2.5; 0.02), decreased Stroop Color-Word test performance (9.4; 3.5; 0.001), increased subjective sleep disturbance (effect size=0.83) and increased objective sleep disturbance (effect size=0.35). Hot flash effects were small to moderate in size. Univariate but not multivariate analyses revealed that all hot flash measures were associated with all affect measures. Different measures of hot flashes associated differently with affect, cognition and sleep. Only nighttime diary-document hot flash consistently correlated with any affect measures in multivariate analyses. The use of differing measures for hot flashes, affect, cognition and sleep may account for the continually reported inconsistencies in menopause study outcomes. This problem impedes forging a consensus on whether hot flashes correlate with neuropsychological symptoms. Copyright © 2015 Elsevier Ireland Ltd. All rights reserved.

Susceptibility to the Flash-Beep Illusion Is Increased in Children Compared to Adults

ERIC Educational Resources Information Center

Innes-Brown, Hamish; Barutchu, Ayla; Shivdasani, Mohit N.; Crewther, David P.; Grayden, David B.; Paolini, Antonio

2011-01-01

Audio-visual integration was studied in children aged 8-17 (N = 30) and adults (N = 22) using the "flash-beep illusion" paradigm, where the presentation of two beeps causes a single flash to be perceived as two flashes ("fission" illusion), and a single beep causes two flashes to be perceived as one flash ("fusion" illusion). Children reported…

Global Patterns of Lightning Properties Derived by OTD and LIS

NASA Technical Reports Server (NTRS)

Beirle, Steffen; Koshak, W.; Blakeslee, R.; Wagner, T.

2014-01-01

The satellite instruments Optical Transient Detector (OTD) and Lightning Imaging Sensor (LIS) provide unique empirical data about the frequency of lightning flashes around the globe (OTD), and the tropics (LIS), which 5 has been used before to compile a well received global climatology of flash rate densities. Here we present a statistical analysis of various additional lightning properties derived from OTD/LIS, i.e. the number of so-called "events" and "groups" per flash, as well as 10 the mean flash duration, footprint and radiance. These normalized quantities, which can be associated with the flash "strength", show consistent spatial patterns; most strikingly, oceanic flashes show higher values than continental flashes for all properties. Over land, regions with high (Eastern US) 15 and low (India) flash strength can be clearly identified. We discuss possible causes and implications of the observed regional differences. Although a direct quantitative interpretation of the investigated flash properties is difficult, the observed spatial patterns provide valuable information for the 20 interpretation and application of climatological flash rates. Due to the systematic regional variations of physical flash characteristics, viewing conditions, and/or measurement sensitivities, parametrisations of lightning NOx based on total flash rate densities alone are probably affected by regional biases.

Characteristics of Lightning Within Electrified Snowfall Events Using Lightning Mapping Arrays

NASA Astrophysics Data System (ADS)

Schultz, Christopher J.; Lang, Timothy J.; Bruning, Eric C.; Calhoun, Kristin M.; Harkema, Sebastian; Curtis, Nathan

2018-02-01

This study examined 34 lightning flashes within four separate thundersnow events derived from lightning mapping arrays (LMAs) in northern Alabama, central Oklahoma, and Washington DC. The goals were to characterize the in-cloud component of each lightning flash, as well as the correspondence between the LMA observations and lightning data taken from national lightning networks like the National Lightning Detection Network (NLDN). Individual flashes were examined in detail to highlight several observations within the data set. The study results demonstrated that the structures of these flashes were primarily normal polarity. The mean area encompassed by this set of flashes is 375 km2, with a maximum flash extent of 2,300 km2, a minimum of 3 km2, and a median of 128 km2. An average of 2.29 NLDN flashes were recorded per LMA-derived lightning flash. A maximum of 11 NLDN flashes were recorded in association with a single LMA-derived flash on 10 January 2011. Additionally, seven of the 34 flashes in the study contain zero NLDN-identified flashes. Eleven of the 34 flashes initiated from tall human-made objects (e.g., communication towers). In at least six lightning flashes, the NLDN detected a return stroke from the cloud back to the tower and not the initial upward leader. This study also discusses lightning's interaction with the human-built environment and provides an example of lightning within heavy snowfall observed by Geostationary Operational Environmental Satellite-16's Geostationary Lightning Mapper.

Hot flashes in breast cancer survivors: Frequency, severity and impact.

PubMed

Chang, Hao-Yuan; Jotwani, Aparna C; Lai, Yeur-Hur; Jensen, Mark P; Syrjala, Karen L; Fann, Jesse R; Gralow, Julie

2016-06-01

To (1) determine the frequency and severity of hot flashes, (2) examine the associations between hot flash frequency and severity and quality of life, and (3) identify the predictors of hot flash activity in breast cancer survivors. The study used a cross-sectional design and mailed survey of 253 breast cancer survivors recruited from a cancer wellness clinic. Participants provided information regarding cancer history, hot flashes, pain intensity, sleep problems, physical functioning, and psychological functioning. About half of the survivors reported at least one hot flash in the past 24 h (45%) or past week (52%). The average frequency of hot flashes was 1.9 in the past 24 h and 1.8 in the past week. Hot flash severity was usually mild or asymptomatic. However, participants with hot flashes reported significantly more sleep problems and higher pain severity than those reporting no hot flashes. Moreover, the severity of hot flashes was associated with more sleep problems, higher pain severity, and more psychological dysfunction. History of hormonal suppression therapy and younger age predicted hot flash activity in the study sample. In breast cancer survivors, hot flashes are common and are associated with unpleasant symptoms and poor quality of life. Research is needed to determine if treatments that reduce the frequency and severity of hot flashes in breast cancer survivors also result in improvements in symptoms such as sleep problems, pain, and psychological dysfunction. Copyright © 2016 Elsevier Ltd. All rights reserved.

Hot flashes in breast cancer survivors: Frequency, severity and impact

PubMed Central

Chang, Hao-Yuan; Jotwani, Aparna C.; Lai, Yeur-Hur; Jensen, Mark P.; Syrjala, Karen L.; Fann, Jesse R.; Gralow, Julie

2018-01-01

Purposes To (1) determine the frequency and severity of hot flashes, (2) examine the associations be- tween hot flash frequency and severity and quality of life, and (3) identify the predictors of hot flash activity in breast cancer survivors. Methods The study used a cross-sectional design and mailed survey of 253 breast cancer survivors recruited from a cancer wellness clinic. Participants provided information regarding cancer history, hot flashes, pain intensity, sleep problems, physical functioning, and psychological functioning. Results About half of the survivors reported at least one hot flash in the past 24 h (45%) or past week (52%). The average frequency of hot flashes was 1.9 in the past 24 h and 1.8 in the past week. Hot flash severity was usually mild or asymptomatic. However, participants with hot flashes reported significantly more sleep problems and higher pain severity than those reporting no hot flashes. Moreover, the severity of hot flashes was associated with more sleep problems, higher pain severity, and more psychological dysfunction. History of hormonal suppression therapy and younger age predicted hot flash activity in the study sample. Conclusions In breast cancer survivors, hot flashes are common and are associated with unpleasant symptoms and poor quality of life. Research is needed to determine if treatments that reduce the frequency and severity of hot flashes in breast cancer survivors also result in improvements in symptoms such as sleep problems, pain, and psychological dysfunction. PMID:27065357

Characteristics of Lightning within Electrified Snowfall Events using Lightning Mapping Arrays.

PubMed

Schultz, Christopher J; Lang, Timothy J; Bruning, Eric C; Calhoun, Kristin M; Harkema, Sebastian; Curtis, Nathan

2018-02-27

This study examined 34 lightning flashes within four separate thundersnow events derived from lightning mapping arrays (LMAs) in northern Alabama, central Oklahoma, and Washington DC. The goals were to characterize the in-cloud component of each lightning flash, as well as the correspondence between the LMA observations and lightning data taken from national lightning networks like the National Lightning Detection Network (NLDN). Individual flashes were examined in detail to highlight several observations within the dataset. The study results demonstrated that the structures of these flashes were primarily normal polarity. The mean area encompassed by this set of flashes is 375 km 2 , with a maximum flash extent of 2300 km 2 , a minimum of 3 km 2 , and a median of 128 km 2 . An average of 2.29 NLDN flashes were recorded per LMA-derived lightning flash. A maximum of 11 NLDN flashes were recorded in association with a single LMA-derived flash on 10 January 2011. Additionally, seven of the 34 flashes in the study contain zero NLDN identified flashes. Eleven of the 34 flashes initiated from tall human-made objects (e.g., communication towers). In at least six lightning flashes, the NLDN detected a return stroke from the cloud back to the tower and not the initial upward leader. This study also discusses lightning's interaction with the human built environment and provides an example of lightning within heavy snowfall observed by GOES-16's Geostationary Lightning Mapper.

Publications - GMC 192 | Alaska Division of Geological & Geophysical

Science.gov Websites

DGGS GMC 192 Publication Details Title: Compressive and shear wave velocity measurements as brine , Compressive and shear wave velocity measurements as brine-saturated measurements (volume 1) and as soltrol

Brine Migration in Heated Salt: Lessons Learned from Field Experiments

NASA Astrophysics Data System (ADS)

Kuhlman, K. L.; Matteo, E. N.; Mills, M.

2017-12-01

We summarize several interesting brine migration related phenomena hinted at in field experiments from field testing related to salt radioactive waste repositories in Germany and the US. Past heater tests in salt have shown 1) thermal-hydrological-mechanical coupling is quite strong during both heating and cooling; 2) chemical composition of brine evolves during heating, and comprises a mix of several water sources; and 3) acid gas (HCl) generation has been observed during past heater tests and may have multiple mechanisms for formation. We present a heated brine migration test design, formulated with these complexities in mind. Sandia National Laboratories is a multimission laboratory managed and operated by National Technology and Engineering Solutions of Sandia LLC, a wholly owned subsidiary of Honeywell International Inc. for the U.S. Department of Energy's National Nuclear Security Administration under contract DE-NA0003525.

Lithium

USGS Publications Warehouse

Bradley, Dwight C.; Stillings, Lisa L.; Jaskula, Brian W.; Munk, LeeAnn; McCauley, Andrew D.; Schulz, Klaus J.; DeYoung,, John H.; Seal, Robert R.; Bradley, Dwight C.

2017-12-19

Lithium, the lightest of all metals, is used in air treatment, batteries, ceramics, glass, metallurgy, pharmaceuticals, and polymers. Rechargeable lithium-ion batteries are particularly important in efforts to reduce global warming because they make it possible to power cars and trucks from renewable sources of energy (for example, hydroelectric, solar, or wind) instead of by burning fossil fuels. Today, lithium is extracted from brines that are pumped from beneath arid sedimentary basins and extracted from granitic pegmatite ores. The leading producer of lithium from brine is Chile, and the leading producer of lithium from pegmatites is Australia. Other potential sources of lithium include clays, geothermal brines, oilfield brines, and zeolites. Worldwide resources of lithium are estimated to be more than 39 million metric tons, which is enough to meet projected demand to the year 2100. The United States is not a major producer at present but has significant lithium resources.

Investigating the Martian Gullies for Possible Brine Origin: A Preliminary Search for Evaporite Minerals Using THEMIS Data

NASA Technical Reports Server (NTRS)

Lane, M. D.; Christensen, P. R.

2003-01-01

Photographs taken by both the Mars Orbiter Camera (MOC) aboard the Mars Global Surveyor (MGS) spacecraft and the Thermal Emission Imaging System (THEMIS) aboard the Mars Odyssey (MO) spacecraft have shown the presence of young gullies on Mars. These gullies occur at middle and high latitudes (predominantly in the southern hemisphere) in the walls of both impact craters and canyons. They are thought possibly to be formed by the melting of ground ice, groundwater seepage (possibly as brines), surface runoff, or even liquid CO2, activated sporadically as a result of oscillations in Mars orbit. For this work, the hypothesis of gully formation being related to the outflow of brines will be investigated through the observation and study of spacecraft data. Brine rich fluids expunged from underground onto the walls of canyons and craters would either evaporate or freeze and sublimate. Removal of water from a brine by evaporation or sublimation would cause the solutes to precipitate as evaporite minerals on the canyon and crater walls or at the base of the walls, and possibly on the canyon and crater floors. Hence, the gully sites are ideal target areas to search for evaporites using THEMIS data. The objective of this work is to survey the recently acquired THEMIS data for spectral evidence of evaporite minerals, with a focus on areas of gully formation. Identifying salt mineral residues could provide chemical evidence in support of the brine origin of the Martian gullies.

A Novel Ion Exchange System to Purify Mixed ISS Waste Water Brines for Chemical Production and Enhanced Water Recovery

NASA Technical Reports Server (NTRS)

Lunn, Griffin Michael; Spencer, LaShelle E.; Ruby, Anna Maria; McCaskill, Andrew

2014-01-01

Current International Space Station water recovery regimes produce a sizable portion of waste water brine. This brine is highly toxic and water recovery is poor: a highly wasteful proposition. With new biological techniques that do not require waste water chemical pretreatment, the resulting brine would be chromium-free and nitrate rich which can allow possible fertilizer recovery for future plant systems. Using a system of ion exchange resins we can remove hardness, sulfate, phosphate and nitrate from these brines to leave only sodium and potassium chloride. At this point modern chlor-alkali cells can be utilized to produce a low salt stream as well as an acid and base stream. The first stream can be used to gain higher water recovery through recycle to the water separation stage while the last two streams can be used to regenerate the ion exchange beds used here, as well as other ion exchange beds in the ISS. Conveniently these waste products from ion exchange regeneration would be suitable as plant fertilizer. In this report we go over the performance of state of the art resins designed for high selectivity of target ions under brine conditions. Using ersatz ISS waste water we can evaluate the performance of specific resins and calculate mass balances to determine resin effectiveness and process viability. If this system is feasible then we will be one step closer to closed loop environmental control and life support systems (ECLSS) for current or future applications.

Composition and source of salinity of ore-bearing fluids in Cu-Au systems of the Carajás Mineral Province, Brazil

USGS Publications Warehouse

Xavier, Roberto; Rusk, Brian; Emsbo, Poul; Monteiro, Lena

2009-01-01

The composition and Cl/Br – NaCl ratios of highly saline aqueous inclusions from large tonnage (> 100 t) IOCG deposits (Sossego, Alvo 118, and Igarapé Bahia) and a Paleoproterozoic intrusion-related Cu-Au-(Mo-W-Bi-Sn) deposit (Breves; < 50 Mt)) in the Carajás Mineral Province have been analysed by LA-ICP-MS and ion chromatography. In both Cu-Au systems, brine inclusions are Ca-dominated (5 to 10 times more than in porphyry Cu-Au fluids), and contain percent level concentrations of Na and K. IOCG inclusion fluids, however, contain higher Sr, Ba, Pb, and Zn concentrations, but significantly less Bi, than the intrusion-related Breves inclusion fluids. Cu is consistently below detection limits in brine inclusions from the IOCG and intrusion-related systems and Fe was not detected in the latter. Cl/Br and Na/Cl ratios of the IOCG inclusion fluids range from entirely evaporative brines (bittern fluids; e.g. Igarapé Bahia and Alvo 118) to values that indicate mixing with magma-derived brines. Cl/Br and Na/Cl ratios of the Breves inclusion fluids strongly suggest the involvement of magmatic brines, but that possibly also incorporated bittern fluids. Collectively, these data demonstrate that residual evaporative and magmatic brines were important components of the fluid regime involved in the formation of Cu-Au systems in the Carajás Mineral Province.

Supercooling and Ice Formation of Perchlorate Brines under Mars-relevant Conditions

NASA Astrophysics Data System (ADS)

Primm, K.; Gough, R. V.; Tolbert, M. A.

2015-12-01

Perchlorate salts, discovered in the Martian regolith at multiple landing sites, may provide pathways for liquid water stability on current Mars. It has previously been assumed that if perchlorate brines form in the Martian regolith via melting or deliquescence, they would be present only briefly because efflorescence into a crystal or freezing to ice would soon occur. Here, we used a Raman microscope to study the temperature and relative humidity (RH) conditions at which magnesium perchlorate brine will form ice. Although ice is thermodynamically predicted to form whenever the saturation with respect to ice (Sice) is greater than or equal to 1, ice formation by perchlorate brines did not occur until elevated Sice values were reached: Sice= 1.17, 1.29, and 1.25 at temperatures of 218 K, 230.5 K, and 244 K, respectively. If a magnesium perchlorate particle was allowed to deliquesce completely prior to experiencing ice supersaturation, the extent of supercooling was increased even further. These high supersaturation values imply perchlorate brines can exist over a wider range of conditions than previously believed. From these experiments it has been found that magnesium perchlorate exhibits supercooling well into the previous theoretical ice region of the stability diagram and that liquid brines on Mars could potentially exist for up to two additional hours per sol. This supercooling of magnesium perchlorate will help with the exploration of Mars by the Mars 2020 spacecraft by helping to understand the phase and duration of water existing in the Martian subsurface.

Natural heat storage in a brine-filled solar pond in the Tully Valley of central New York

USGS Publications Warehouse

Hayhurst, Brett; Kappel, William M.

2014-01-01

The Tully Valley, located in southern Onondaga County, New York, has a long history of unusual natural hydrogeologic phenomena including mudboils (Kappel, 2009), landslides (Tamulonis and others, 2009; Pair and others, 2000), landsurface subsidence (Hackett and others, 2009; Kappel, 2009), and a brine-filled sinkhole or “Solar pond” (fig. 1), which is documented in this report. A solar pond is a pool of salty water (brine) which stores the sun’s energy in the form of heat. The saltwater naturally forms distinct layers with increasing density between transitional zones (haloclines) of rapidly changing specific conductance with depth. In a typical solar pond, the top layer has a low salt content and is often times referred to as the upper convective zone (Lu and others, 2002). The bottom layer is a concentrated brine that is either convective or temperature stratified dependent on the surrounding environment. Solar insolation is absorbed and stored in the lower, denser brine while the overlying halocline acts as an insulating layer and prevents heat from moving upwards from the lower zone (Lu and others, 2002). In the case of the Tully Valley solar pond, water within the pond can be over 90 degrees Fahrenheit (°F) in late summer and early fall. The purpose of this report is to summarize observations at the Tully Valley brine-filled sinkhole and provide supplemental climate data which might affect the pond salinity gradients insolation (solar energy).

Field-scale Thermal Testing in a Generic Salt Disposal Environment Underground Research Laboratory (URL): Delineation of Principal Purpose Objectives and Hypotheses

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sassani, David C.; Hardin, Ernest L.; Kuhlman, Kristopher L

The amount of brine present in domal salt formation is far less than in bedded salts (e.g., 0.01 to 0.1% compared with 1 to 3%). In salt domes, shear deformation associated with diapirism has caused existing brine to coalesce, leading to flow and expulsion. Brine migration behavior was investigated in bedded salt at WIPP (Nowak and McTigue 1987, SAND87-0880), and in domal salt at Asse (Coyle et al. 1987, BMI/ONWI-624). Test methods were not standardized, and the tests involved large diameter boreholes (17 to 36 in. diameter) and large apparatus. The tested intervals were proximal to mined openings (within approximatelymore » 1 diameter) where in situ stresses are redistributed due to excavation. The tests showed that (1) brine inflow rates can range over at least 2 orders of magnitude for domal vs. bedded salt, (2) that brine inflow is strongly associated with clay and interbedded permeable layers in bedded salt, and (3) that measurement systems can readily collect very small quantities of moisture over time frames of 2 years or longer. Brine inflow rates declined slightly with time in both test series, but neither series approached a state of apparent depletion. This range of flow magnitude could be significant to repository design and performance assessment, especially if inflow rates can be predicted using stratigraphic and geomechanical inputs, and can be shown to approach zero in a predictable manner.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gilbert, Kimberly; Bennett, Philip C.; Wolfe, Will

Dissolution of CO2 into deep subsurface brines for carbon sequestration is regarded as one of the few viable means of reducing the amount of CO2 entering the atmosphere. Ions in solution partially control the amount of CO2 that dissolves, but the mechanisms of the ion's influence are not clearly understood and thus CO2 solubility is difficult to predict. In this study, CO2 solubility was experimentally determined in water, NaCl, CaCl2, Na2SO4, and NaHCO3 solutions and a mixed brine similar to the Bravo Dome natural CO2 reservoir; ionic strengths ranged up to 3.4 molal, temperatures to 140 °C, and CO2 pressuresmore » to 35.5 MPa. Increasing ionic strength decreased CO2 solubility for all solutions when the salt type remained unchanged, but ionic strength was a poor predictor of CO2 solubility in solutions with different salts. A new equation was developed to use ion hydration number to calculate the concentration of electrostricted water molecules in solution. Dissolved CO2 was strongly correlated (R2 = 0.96) to electrostricted water concentration. Strong correlations were also identified between CO2 solubility and hydration enthalpy and hydration entropy. These linear correlation equations predicted CO2 solubility within 1% of the Bravo Dome brine and within 10% of two mixed brines from literature (a 10 wt % NaCl + KCl + CaCl2 brine and a natural Na+, Ca2+, Cl- type brine with minor amounts of Mg2+, K+, Sr2+ and Br-).« less

FLASH2: Operation, beamlines, and photon diagnostics

DOE Office of Scientific and Technical Information (OSTI.GOV)

Plönjes, Elke, E-mail: elke.ploenjes@desy.de; Faatz, Bart; Kuhlmann, Marion

2016-07-27

FLASH2, a major extension of the soft X-ray free-electron laser FLASH at DESY, turns FLASH into a multi-user FEL facility. A new undulator line is located in a separate accelerator tunnel and driven additionally by the FLASH linear accelerator. First lasing of FLASH2 was achieved in August 2014 with simultaneous user operation at FLASH1. The new FLASH2 experimental hall offers space for up to six experimental end stations, some of which will be installed permanently. The wide wavelength range spans from 4-60 nm and 0.8 nm in the 5{sup th} harmonic and in the future deep into the water windowmore » in the fundamental. While this is of high interest to users, it is challenging from the beamline instrumentation point of view. Online diagnostics - which are mostly pulse resolved - for beam intensity, position, wavelength, wave front, and pulse length have been to a large extent developed at FLASH(1) and have now been optimized for FLASH2. Pump-probe facilities for XUV-XUV, XUV optical and XUV-THz experiments will complete the FLASH2 user facility.« less

A Pliocene marine diatom δ18O record of terrestrial-marine feedbacks and orbitally-paced cryogenic brine formation in the McMurdo Dry Valleys

NASA Astrophysics Data System (ADS)

Dodd, J. P.; Abbott, T.; Gibbons, J. A.

2017-12-01

Orbital frequencies are well documented in a number of terrestrial and marine climate records throughout the Cenozoic; however, assessing the feedbacks and timing of terrestrial-marine systems on glacial-interglacial timescales is often challenging. This is particularly the case in high-latitude, near-shore environments where traditional proxy records like benthic foraminifera are absent. Here we present oxygen isotope (δ18O and δ17O) values from marine diatom silica in the mid-Pliocene (3.5 - 4.7Ma) section of the AND-1B core from McMurdo Sound, Antarctica. Diatom silica δ18O values range between +28.1 and +36.4‰ VSMOW. Over a range of temperatures (0 to 10°C) that reflect both growth and shallow (<100mbsf) diagenetic conditions, the calculated formation water δ18O values range from -14.7 to -6.7 (± 1.7)‰. The diatom silica δ18O values are in close agreement with the average pore water δ18O values in the nearby AND-2A sediment core of -10 ± 1‰. Pore water chemistry reflects cryogenic brines that formed through progressive freezing of seawater and mirabilite formation. Our calculated pore water δ18O values for the AND-1B core support the cryogenic brine hypothesis, with very low δ18O values during the mid-Pliocene interval. Δ17O values of the biogenic silica reflect formation water that does not fall on a mixing line between marine and meteoric waters, which also supports our cryogenic brine hypothesis. The AND-1B δ18O values have an inverse relationship with the stacked benthic foraminifera δ18O record where lower δ18O values in the AND-1B diatom silica correspond with colder intervals, and we interpret variations in the diatom δ18O values as increased brine flux from the MDV to McMurdo Sound. Currently, subsurface brines in the MDV are hydrologically connected with McMurdo Sound. Density-driven transport of these brines from the MDV to the marine costal environments during the warm mid-Pliocene indicate a potentially overlooked terrestrial source of hypersaline waters. Although the lateral extent of these brines is not known, mixing between the terrestrial cryogenic brines and seawater may represent a significant flux of hypersaline water to the marine environment during warmer-than-present global conditions.

Diffusive leakage of brine from aquifers during CO2 geological storage

NASA Astrophysics Data System (ADS)

Dejam, Morteza; Hassanzadeh, Hassan

2018-01-01

The area of investigation in this study is designed around an improved understanding of fundamentals of the diffusive leakage of brine from a storage aquifer into overlying and underlying low permeability layers during geosequestration of carbon dioxide (CO2) through development of a theoretical model. Here, we consider a two-dimensional domain in cylindrical coordinates, comprised of an aquifer and an overburden, where the interaction between the two media is handled by imposing the continuities of pressures and fluid fluxes at the aquifer-overburden interface. This coupled problem is solved by successive implementation of the Laplace and finite Hankel transforms. The developed solutions can be used to analyze diffusive leakage of brine from the aquifer into overburden and generate type curves for average pressures in the aquifer and overburden during injection and post injection periods. The results show that the leakage rate at early times is scaled with t1/2 while it remains constant at late times. It is also shown that the average pressure in the aquifer is scaled with t for short and long times. Moreover, the average pressure in the overburden is scaled with t at late times while it is scaled with t3/2 at early times. In addition, the results reveal that factors affecting diffusive leakage rate through intact overburden during CO2 storage are, in decreasing order of significance, thickness of overburden, thickness of aquifer, aquifer to overburden permeability ratio, and aquifer to overburden porosity ratio. However, thickness of aquifer has minimal effect on diffusive leakage of brine within post injection period. To evaluate the theoretical model, case studies for two potential sites in United Kingdom, one in Lincolnshire and the other one in the Firth of Forth, are conducted. The field studies show that the diffusive leakage from the aquifer into the overburden diminishes ∼40 years after the injection has ceased for Lincolnshire while it stops after ∼12 years for Firth of Forth. The average amount of the brine leaked from the aquifers per standard cubic meter (Sm3) of the injected CO2 through diffusive leakage was found to be 6.28 × 10-4 m3 of brine (or 0.330 kg of brine/kg of CO2) over ∼70 years for Lincolnshire and 4.59 × 10-4 m3 of brine (or 0.242 kg of brine/kg of CO2) over ∼42 years for Firth of Forth.

The Synthesis of Calcium Salt from Brine Water by Partial Evaporation and Chemical Precipitation

NASA Astrophysics Data System (ADS)

Lalasari, L. H.; Widowati, M. K.; Natasha, N. C.; Sulistiyono, E.; Prasetyo, A. B.

2017-02-01

In this study would be investigated the effects of partial evaporation and chemical precipitation in the formation of calcium salt from brine water resources. The chemical reagents used in the study was oxalate acid (C2H2O4), ammonium carbonate (NH4)2CO3) and ammonium hydroxide (NH4OH) with reagent concentration of 2 N, respectively. The procedure was 10 liters brine water evaporated until 20% volume and continued with filtration process to separate brine water filtrate from residue (salt). Salt resulted from evaporation process was characterized by Scanning Electron Microscopy (SEM), X-Ray Fluorescence (XRF) and X-Ray Diffraction (XRD) techniques. Filtrate then was reacted with C2H2O4, (NH4)2CO3 and NH4OH reagents to get salt products in atmospheric condition and variation ratio volume brine water/chemicals (v/v) [10/1; 10/5; 10/10; 10/20; 10/30; 10:50; 20/1; 20/5; 20/10; 20/20; 20/30; 20:50]. The salt product than were filtered, dried, measured weights and finally characterized by SEM/EDS and XRD techniques. The result of experiment showed the chemical composition of brine water from Tirta Sanita, Bogor was 28.87% Na, 9.17% Mg, 2.94% Ca, 22.33% O, 0.71% Sr, 30.02% Cl, 1.51% Si, 1.23% K, 0.55% S, 1.31% Al. The chemical composition of salt resulted by partial evaporation was 53.02% Ca, 28.93%O, 9.50% Na, 2.10% Mg, 1.53% Sr, 1.20% Cl, 1.10% Si, 0.63% K, 0.40% S, 0.39% Al. The salt resulted by total evaporation was indicated namely as NaCl. Whereas salt resulted by partial evaporation was CaCO3 with a purity of 90 % from High Score Plus analysis. In the experiment by chemical precipitation was reported that the reagents of ammonium carbonate were more reactive for synthesizing calcium salt from brine water compared to reagents of oxalate acid and ammonium hydroxide. The salts precipitated by NH4OH, (NH4)2CO3, and H2C2O4 reagents were indicated as NaCl, CaCO3 and CaC2O4.H2O, respectively. The techniques of partial evaporation until 20% volume sample of brine water and chemical precipitation using (NH4)2CO3 reagent are recommended in the synthesis of calcium salts from brine water because are simple, flexible and economical.

Brines formed by multi-salt deliquescence

DOE Office of Scientific and Technical Information (OSTI.GOV)

Carroll, S; Rard, J; Alai, M

2005-11-04

The FY05 Waste Package Environment testing program at Lawrence Livermore National Laboratory focused on determining the temperature, relative humidity, and solution compositions of brines formed due to the deliquescence of NaCl-KNO{sub 3}-NaNO{sub 3} and NaCl-KNO{sub 3}-NaNO{sub 3}-Ca(NO{sub 3}){sub 2} salt mixtures. Understanding the physical and chemical behavior of these brines is important because they define conditions under which brines may react with waste canister surfaces. Boiling point experiments show that NaCl-KNO{sub 3}-NaNO{sub 3} and NaCl-KNO{sub 3}-NaNO{sub 3}-Ca(NO{sub 3}){sub 2} salt mixtures form brines that transform to hydrous melts that do not truly 'dry out' until temperatures exceed 300 and 400more » C, respectively. Thus a conducting solution is present for these salt assemblages over the thermal history of the repository. The corresponding brines form at lower relative humidity at higher temperatures. The NaCl-KNO{sub 3}-NaNO{sub 3} salt mixture has a mutual deliquescence relative humidity (MDRH) of 25.9% at 120 C and 10.8% at 180 C. Similarly, the KNO{sub 3}-NaNO{sub 3} salt mixture has MDRH of 26.4% at 120 C and 20.0% at 150 C. The KNO{sub 3}-NaNO{sub 3} salt mixture salts also absorb some water (but do not appear to deliquesce) at 180 C and thus may also contribute to the transfer of electrons at interface between dust and the waste package surface. There is no experimental evidence to suggest that these brines will degas and form less deliquescent salt assemblages. Ammonium present in atmospheric and tunnel dust (as the chloride, nitrate, or sulfate) will readily decompose in the initial heating phase of the repository, and will affect subsequent behavior of the remaining salt mixture only through the removal of a stoichiometric equivalent of one or more anions. Although K-Na-NO{sub 3}-Cl brines form at high temperature and low relative humidity, these brines are dominated by nitrate, which is known to inhibit corrosion at lower temperature. Nitrate to chloride ratios of the NaCl-KNO{sub 3}-NaNO{sub 3} salt mixture are about NO{sub 3}:Cl = 19:1. The role of nitrate on corrosion at higher temperatures is addressed in a companion report (Dixit et al., 2005).« less

Effect of matrix components on UV/H2O2 and UV/S2O8(2-) advanced oxidation processes for trace organic degradation in reverse osmosis brines from municipal wastewater reuse facilities.

PubMed

Yang, Yi; Pignatello, Joseph J; Ma, Jun; Mitch, William A

2016-02-01

When reverse osmosis brines from potable wastewater reuse plants are discharged to poorly-flushed estuaries, the concentrated organic contaminants are a concern for receiving water ecosystems. UV/hydrogen peroxide (UV/H2O2) and UV/persulfate (UV/S2O8(2-)) advanced oxidation processes (AOPs) may reduce contaminant burdens prior to discharge, but the effects of the high levels of halide, carbonate and effluent organic matter (EfOM) normally present in these brines are unclear. On the one hand, these substances may reduce process efficiency by scavenging reactive oxygen species (ROS), hydroxyl (OH) and sulfate (SO4(-) radicals. On the other, the daughter radicals generated by halide and carbonate scavenging may themselves degrade organics, offsetting the effect of ROS scavenging. UV/H2O2 and UV/S2O8(2-) AOPs were compared for degradation of five pharmaceuticals spiked into brines obtained from two reuse facilities and the RO influent from one of them. For UV/H2O2, EfOM scavenged ∼75% of the OH, reducing the degradation efficiency of the target contaminants to a similar extent; halide and carbonate scavenging and the reactivities of associated daughter radicals were less important. For UV/S2O8(2-), anions (mostly Cl(-)) scavenged ∼93% of the SO4(-). Because daughter radicals of Cl(-) contributed to contaminant degradation, the reduction in contaminant degradation efficiency was only ∼75-80%, with the reduction driven by daughter radical scavenging by EfOM. Conversion of SO4(-) to more selective halogen and carbonate radicals resulted in a wider range of degradation efficiencies among the contaminants. For both AOPs, 250 mJ/cm(2) average fluence achieved significant removal of four pharmaceuticals, with significantly better performance by UV/S2O8(2-) treatment for some constituents. Accounting for the lower brine flowrates, the energy output to achieve this fluence in brines is comparable to that often applied to RO permeates. However, much higher fluence was required for the least reactive pharmaceutical. Comparing AOP application to the RO influent or brine, equal or greater removal was achieved for brine treatment for comparable energy input. AOP treatment of brines could be applied to reduce, but not eliminate, contaminant burdens prior to discharge. Copyright © 2015 Elsevier Ltd. All rights reserved.

Magnitude of the impact of hot flashes on sleep in perimenopausal women

PubMed Central

de Zambotti, Massimiliano; Colrain, Ian M.; Javitz, Harold S.; Baker, Fiona C.

2014-01-01

Objective To quantify the impact of objectively-recorded hot flashes on objective sleep in perimenopausal women. Design Cross-sectional study. Participants underwent 1–5 laboratory-based polysomnographic recordings for a total of 63 nights, including sternal skin conductance measures, from which 222 hot flashes were identified according to established criteria. Data were analyzed with hierarchical mixed-effect models and Spearman correlations. Setting Sleep laboratory. Patients 34 perimenopausal women (Age±SD:50.4±2.7y). Intervention None. Main Outcome Measures Perceived and polysomnographic sleep measures (sleep quality, amount of wake after sleep onset and number of awakenings). Subjective (frequency and bother) and objective (frequency and amount of hot flash-associated wake time) hot flash measures. Results Women had an average of 3.5 (95%CI:2.8–4.2, range=1– 9) objective hot flashes per night. 69.4% of hot flashes were associated with an awakening. Hot flash-associated wake time per night was, on average, 16.6 min (95%CI:10.8–22.4), which accounted for 27.2% (SD 27.1) of total wakefulness per night. Hot flash-associated wake, but not frequency, was negatively associated with sleep efficiency and positively associated with wake after sleep onset. Also, self-reported wakefulness correlated with hot flash-associated wake, suggesting that women’s estimates of wakefulness are influenced by the amount of time spent awake in association with hot flashes during the night. More perceived and bothersome hot flashes correlated with more perceived wakefulness and awakenings and more objective hot flash-associated wake time and hot flash frequency. Conclusions The presence of physiological hot flashes accounts for a significant proportion of total objective wakefulness during the night in perimenopausal women. PMID:25256933

Adiposity and Hot Flashes in Midlife Women: A Modifying Role of Age

PubMed Central

Santoro, Nanette; Matthews, Karen A.

2011-01-01

Background: The nature of the relationship between adiposity and hot flashes has been debated, but it has not been examined using physiological measures of hot flashes. We examined associations between body size/composition and physiologically assessed hot flashes among women with hot flashes. Methods: A subcohort of women in the Study of Women's Health Across the Nation (n = 52; 25 African-American and 27 non-Hispanic Caucasian; ages, 54 to 63 yr) who reported hot flashes, had their uterus and ovaries, and were not taking medications impacting hot flashes were recruited in 2008–2009. Women completed anthropometric measures [bioimpedance analysis of total percentage of body fat, body mass index (BMI), waist circumference], a blood draw (estradiol, SHBG, FSH, dehydroepiandrosterone sulfate), and 4 d of ambulatory sternal skin conductance monitoring with diary (physiological and reported hot flashes, respectively). Associations between anthropometrics and hot flashes were estimated with generalized estimating equations with covariates age, race, and anxiety. Results: Higher BMI (odds ratio, 0.97; 95% confidence interval, 0.94–0.99; P < 0.05) and waist circumference (odds ratio, 0.98; 95% confidence interval, 0.97–0.99; P < 0.01) were associated with fewer physiological hot flashes. Interactions by age (P < 0.05) indicated that inverse associations of body fat, BMI, and waist circumference with hot flashes were most apparent among the oldest women in the sample. Estradiol and SHBG reduced but did not eliminate age-related variations in relations between body size/composition and hot flashes. Conclusion: Higher adiposity was associated with fewer physiological hot flashes among older women with hot flashes. A modifying role of age must be considered in understanding the role of adiposity in hot flashes. PMID:21778220

Adiposity and hot flashes in midlife women: a modifying role of age.

PubMed

Thurston, Rebecca C; Santoro, Nanette; Matthews, Karen A

2011-10-01

The nature of the relationship between adiposity and hot flashes has been debated, but it has not been examined using physiological measures of hot flashes. We examined associations between body size/composition and physiologically assessed hot flashes among women with hot flashes. A subcohort of women in the Study of Women's Health Across the Nation (n = 52; 25 African-American and 27 non-Hispanic Caucasian; ages, 54 to 63 yr) who reported hot flashes, had their uterus and ovaries, and were not taking medications impacting hot flashes were recruited in 2008-2009. Women completed anthropometric measures [bioimpedance analysis of total percentage of body fat, body mass index (BMI), waist circumference], a blood draw (estradiol, SHBG, FSH, dehydroepiandrosterone sulfate), and 4 d of ambulatory sternal skin conductance monitoring with diary (physiological and reported hot flashes, respectively). Associations between anthropometrics and hot flashes were estimated with generalized estimating equations with covariates age, race, and anxiety. Higher BMI (odds ratio, 0.97; 95% confidence interval, 0.94-0.99; P < 0.05) and waist circumference (odds ratio, 0.98; 95% confidence interval, 0.97-0.99; P < 0.01) were associated with fewer physiological hot flashes. Interactions by age (P < 0.05) indicated that inverse associations of body fat, BMI, and waist circumference with hot flashes were most apparent among the oldest women in the sample. Estradiol and SHBG reduced but did not eliminate age-related variations in relations between body size/composition and hot flashes. Higher adiposity was associated with fewer physiological hot flashes among older women with hot flashes. A modifying role of age must be considered in understanding the role of adiposity in hot flashes.

Initial Breakdown Pulse Amplitudes in Intracloud and Cloud-to-Ground Lightning Flashes

NASA Astrophysics Data System (ADS)

Marshall, T. C.; Smith, E. M.; Stolzenburg, M.; Karunarathne, S.; Siedlecki, R. D., II

2017-12-01

This study analyzes the largest initial breakdown (IB) pulse in flashes from three storms in Florida. The study was motivated in part by the possibility that IB pulses of IC flashes may cause of terrestrial gamma-ray flashes (TGFs). The range-normalized, zero-to-peak amplitude of the largest IB pulse within each flash was determined along with its altitude, duration, and occurrence time in the flash. Appropriate data were available for 40 intracloud (IC) and 32 cloud-to-ground (CG) flashes. Histograms of the magnitude of the largest IB pulse amplitude by flash type were similar, with mean (median) values of 1.49 (1.05) V/m for IC flashes and -1.35 (-0.87) V/m for CG flashes. The mean amplitude of the largest IC IB pulses are substantially smaller (roughly an order of magnitude smaller) than the few known pulse amplitudes of TGF events and TGF candidate events. The largest IB pulse in 30 IC flashes showed a weak inverse relation between pulse amplitude and altitude. Amplitude of the largest IB pulse for 25 CG flashes showed no altitude correlation. Duration of the largest IB pulse in ICs averaged twice as long as in CGs (96 μs versus 46 μs); all of the CG durations were <100 μs. Among the ICs, there is a positive relation between largest IB pulse duration and amplitude; the linear correlation coefficient is 0.385 with outliers excluded. The largest IB pulse in IC flashes typically occurred at a longer time after the first IB pulse (average 4.1 ms) than was the case in CG flashes (average 0.6 ms). In both flash types, the largest IB pulse was the first IB pulse in about 30% of the cases.

Experimental salinity alleviation at Malaga Bend of the Pecos River, Eddy County, New Mexico

USGS Publications Warehouse

Havens, John S.; Wilkins, D.W.

1979-01-01

Upward-leaking brine, from a confined aquifer at the base of the Rustler Formation, mixes with fresher water in a shallow aquifer , resulting in discharge to the Pecos River in southern Eddy County, New Mexico, of about 0.5 cubic feet per second of saturated brine. Pumping brine from the aquifer at a rate greater than 0.5 cubic feet per second lowered the potentiometric head in the confined aquifer. From July 22, 1963, through December 1968, approximately 3,878 acre-feet of brine had been pumped into the Northeast Depression. The depression leaked brine to the Pecos River. Water downgradient of the depression increased in specific conductance ranging from 1,500 to 99,400 milligrams per liter chloride and water levels near the depression increased over 3 feet from 1963 to 1968. For water years 1952-63, the Pecos River gained about 240 tons per day of chloride in the reach from Malaga gaging station to Pierce Canyon Crossing. The average chloride gain to the Pecos River from July 1963 to August 1966 was 167 tons per day; the 1967-68 gain increased to 256 tons per day after a major flood in August 1966. (USGS)

Formation and Persistence of Brine on Mars: Experimental Simulations throughout the Diurnal Cycle at the Phoenix Landing Site

PubMed Central

Martínez, G.M.; Rennó, N.O.

2016-01-01

Abstract In the last few years, water ice and salts capable of melting this ice and producing liquid saline water (brine) have been detected on Mars. Moreover, indirect evidence for brine has been found in multiple areas of the planet. Here, we simulate full diurnal cycles of temperature and atmospheric water vapor content at the Phoenix landing site for the first time and show experimentally that, in spite of the low Mars-like chamber temperature, brine forms minutes after the ground temperature exceeds the eutectic temperature of salts in contact with water ice. Moreover, we show that the brine stays liquid for most of the diurnal cycle when enough water ice is available to compensate for evaporation. This is predicted to occur seasonally in areas of the polar region where the temperature exceeds the eutectic value and frost or snow is deposited on saline soils, or where water ice and salts coexist in the shallow subsurface. This is important because the existence of liquid water is a key requirement for habitability. Key Words: Mars—Ice—Perchlorates—Brine—Water—Raman spectroscopy. Astrobiology 16, 937–948. PMID:27912028

Role of partial miscibility on pressure buildup due to constant rate injection of CO2 into closed and open brine aquifers

NASA Astrophysics Data System (ADS)

Mathias, Simon A.; Gluyas, Jon G.; GonzáLez MartíNez de Miguel, Gerardo J.; Hosseini, Seyyed A.

2011-12-01

This work extends an existing analytical solution for pressure buildup because of CO2 injection in brine aquifers by incorporating effects associated with partial miscibility. These include evaporation of water into the CO2 rich phase and dissolution of CO2 into brine and salt precipitation. The resulting equations are closed-form, including the locations of the associated leading and trailing shock fronts. Derivation of the analytical solution involves making a number of simplifying assumptions including: vertical pressure equilibrium, negligible capillary pressure, and constant fluid properties. The analytical solution is compared to results from TOUGH2 and found to accurately approximate the extent of the dry-out zone around the well, the resulting permeability enhancement due to residual brine evaporation, the volumetric saturation of precipitated salt, and the vertically averaged pressure distribution in both space and time for the four scenarios studied. While brine evaporation is found to have a considerable effect on pressure, the effect of CO2 dissolution is found to be small. The resulting equations remain simple to evaluate in spreadsheet software and represent a significant improvement on current methods for estimating pressure-limited CO2 storage capacity.

Removal of fouling species from brackish water reverse osmosis reject stream.

PubMed

Ayoub, G M; Korban, L; Al-Hindi, M; Zayyat, R

2018-03-01

Brine disposal from reverse osmosis (RO) systems remains a major challenge for the desalination industry especially in inland areas where discharge options are very limited. Solutions will entail the introduction of economic treatment processes that will alleviate the brine's negative impact on the environment and reduce its discharge volume. Such processes could act as an intermediary treatment process for the recycling of the brine through an additional RO stage which, for brackish water (BW) desalination, could lead to saving valuable water while reducing the amount of brine discharge. In this context, the study at hand attempts to evaluate the effectiveness of a one-step chemical process for the treatment of BWRO brine. This study seeks to determine optimal operating conditions relative to type, ratio, and dosage of alkalizing chemicals, pH and temperature, for substantially reducing the concentrations of scaling parameters such as calcium, magnesium, silica, and strontium. The results indicate that precipitation softening at pH = 11.5 using combined chemical dosages of NaOH and Na 2 CO 3 in a ratio of 2:1 leads to substantial removal of calcium and magnesium (>95%) and moderately high removal of strontium and silica (>71%).

[Experimental interaction of halophilic prokaryotes and opportunistic bacteria in brine].

PubMed

Selivanova, E A; Nemtseva, N V

2013-01-01

Study the effect of extremely halophilic archaea and moderately halophilic bacteria on preservation of opportunistic bacteria in brine. 17 strains of moderately halophilic bacteria and 2 strains of extremely halophilic archaea were isolated from continental hypersaline lake Razval of Sol-Iletsk area of Orenburg Region. Identification of pure cultures of prokaryotes was carried out taking into account their phenotype properties and based on determination of 16S RNA gene sequence. The effect of halophilic prokaryote on elimination of Escherichia coli from brine was evaluated during co-cultivation. Antagonistic activity of cell extracts of the studied microorganisms was evaluated by photometric method. A more prolonged preservation of an E. coli strain in brine in the presence of live cells of extremely halophilic archaea Halorubrum tebenquichense and moderately halophilic bacteria Marinococcus halophilus was established. Extracts of cells of extremely halophilic archaea and moderately halophilic bacteria on the contrary displayed antagonistic activity. The protective effect of live cells of halophilic prokaryotes and antagonistic activity of their cell extracts change the period of conservation of opportunistic bacteria in brine that regulates inter-microbial interactions and changes the period of self-purification that reflects the sanitary condition of a hypersaline water body.

SUMO regulates proteasome-dependent degradation of FLASH/Casp8AP2

PubMed Central

Vennemann, Astrid; Hofmann, Thomas G.

2013-01-01

FLASH/Casp8AP2 is a huge multifunctional protein involved in multiple cellular processes, reaching from death receptor signaling to regulation of histone gene transcription and histone mRNA processing. Previous work has shown that FLASH localizes to Cajal bodies and promyelocytic leukemia (PML) bodies. However, the function of its nuclear body association remains unclear. Here we demonstrate that murine FLASH is covalently modified by SUMO at Lys residue 1792. Interestingly, ectopic expression of SUMO results in proteasome-dependent degradation of FLASH. A point mutant of FLASH with a mutated SUMO acceptor lysine residue, FLASHK1792R, is resistant to SUMO-induced degradation. Finally, we show that arsenic trioxide, a drug known to potentiate SUMO modification and degradation of PML, triggers recruitment of FLASH to PML bodies and concomitant loss of FLASH protein. Our data suggest that SUMO targets FLASH for proteasome-dependent degradation, which is associated with recruitment of FLASH to PML bodies. PMID:23673342

The October 2014 United States Treasury bond flash crash and the contributory effect of mini flash crashes

PubMed Central

Levine, Zachary S.; Floridi, Luciano

2017-01-01

We investigate the causal uncertainty surrounding the flash crash in the U.S. Treasury bond market on October 15, 2014, and the unresolved concern that no clear link has been identified between the start of the flash crash at 9:33 and the opening of the U.S. equity market at 9:30. We consider the contributory effect of mini flash crashes in equity markets, and find that the number of equity mini flash crashes in the three-minute window between market open and the Treasury Flash Crash was 2.6 times larger than the number experienced in any other three-minute window in the prior ten weekdays. We argue that (a) this statistically significant finding suggests that mini flash crashes in equity markets both predicted and contributed to the October 2014 U.S. Treasury Bond Flash Crash, and (b) mini-flash crashes are important phenomena with negative externalities that deserve much greater scholarly attention. PMID:29091931

7 CFR 999.200 - Regulation governing the importation of prunes.

Code of Federal Regulations, 2013 CFR

2013-01-01

... preservation; and (iii) brine dried prunes that have been impregnated with brine or salt during the dehydration... means injury by sunburn or excessive heat in dehydration to the extent that the characteristic...

Measuring salt retention : [summary].

DOT National Transportation Integrated Search

2013-03-01

This project involves measuring and reporting the retention of salt and brine on the roadway as a result of using different salt spreaders, application speeds, and brine quantities. The research develops an evaluation methodology, directs the field c...

7 CFR 999.200 - Regulation governing the importation of prunes.

Code of Federal Regulations, 2014 CFR

2014-01-01

... preservation; and (iii) brine dried prunes that have been impregnated with brine or salt during the dehydration... means injury by sunburn or excessive heat in dehydration to the extent that the characteristic...

7 CFR 999.200 - Regulation governing the importation of prunes.

Code of Federal Regulations, 2012 CFR

2012-01-01

... preservation; and (iii) brine dried prunes that have been impregnated with brine or salt during the dehydration... means injury by sunburn or excessive heat in dehydration to the extent that the characteristic...

7 CFR 999.200 - Regulation governing the importation of prunes.

Code of Federal Regulations, 2011 CFR

2011-01-01

... preservation; and (iii) brine dried prunes that have been impregnated with brine or salt during the dehydration... means injury by sunburn or excessive heat in dehydration to the extent that the characteristic...

15 CFR 922.122 - Prohibited or otherwise regulated activities.

Code of Federal Regulations, 2010 CFR

2010-01-01

... other bottom formation, coralline algae or other plant, marine invertebrate, brine-seep biota or... invertebrate, brine-seep biota or fish (except for fish caught by use of conventional hook and line gear). (9...

Brine stability study

DOE Data Explorer

Gary Garland

2015-04-15

This is a study of the brine formulations that we were using in our testing were stable over time. The data includes charts, as well as, all of the original data from the ICP-MS runs to complete this study.

PIAS1 interacts with FLASH and enhances its co-activation of c-Myb

PubMed Central

2011-01-01

Background FLASH is a huge nuclear protein involved in various cellular functions such as apoptosis signalling, NF-κB activation, S-phase regulation, processing of histone pre-mRNAs, and co-regulation of transcription. Recently, we identified FLASH as a co-activator of the transcription factor c-Myb and found FLASH to be tightly associated with active transcription foci. As a huge multifunctional protein, FLASH is expected to have many interaction partners, some which may shed light on its function as a transcriptional regulator. Results To find additional FLASH-associated proteins, we performed a yeast two-hybrid (Y2H) screening with FLASH as bait and identified the SUMO E3 ligase PIAS1 as an interaction partner. The association appears to involve two distinct interaction surfaces in FLASH. We verified the interaction by Y2H-mating, GST pulldowns, co-IP and ChIP. FLASH and PIAS1 were found to co-localize in nuclear speckles. Functional assays revealed that PIAS1 enhances the intrinsic transcriptional activity of FLASH in a RING finger-dependent manner. Furthermore, PIAS1 also augments the specific activity of c-Myb, and cooperates with FLASH to further co-activate c-Myb. The three proteins, FLASH, PIAS1, and c-Myb, are all co-localized with active RNA polymerase II foci, resembling transcription factories. Conclusions We conclude that PIAS1 is a common partner for two cancer-related nuclear factors, c-Myb and FLASH. Our results point to a functional cooperation between FLASH and PIAS1 in the enhancement of c-Myb activity in active nuclear foci. PMID:21338522

"Know What to Do If You Encounter a Flash Flood": Mental Models Analysis for Improving Flash Flood Risk Communication and Public Decision Making.

PubMed

Lazrus, Heather; Morss, Rebecca E; Demuth, Julie L; Lazo, Jeffrey K; Bostrom, Ann

2016-02-01

Understanding how people view flash flood risks can help improve risk communication, ultimately improving outcomes. This article analyzes data from 26 mental models interviews about flash floods with members of the public in Boulder, Colorado, to understand their perspectives on flash flood risks and mitigation. The analysis includes a comparison between public and professional perspectives by referencing a companion mental models study of Boulder-area professionals. A mental models approach can help to diagnose what people already know about flash flood risks and responses, as well as any critical gaps in their knowledge that might be addressed through improved risk communication. A few public interviewees mentioned most of the key concepts discussed by professionals as important for flash flood warning decision making. However, most interviewees exhibited some incomplete understandings and misconceptions about aspects of flash flood development and exposure, effects, or mitigation that may lead to ineffective warning decisions when a flash flood threatens. These include important misunderstandings about the rapid evolution of flash floods, the speed of water in flash floods, the locations and times that pose the greatest flash flood risk in Boulder, the value of situational awareness and environmental cues, and the most appropriate responses when a flash flood threatens. The findings point to recommendations for ways to improve risk communication, over the long term and when an event threatens, to help people quickly recognize and understand threats, obtain needed information, and make informed decisions in complex, rapidly evolving extreme weather events such as flash floods. © 2015 Society for Risk Analysis.

Hot Flashes and Carotid Intima Media Thickness among Midlife Women

PubMed Central

Thurston, Rebecca C.; Sutton-Tyrrell, Kim; Everson-Rose, Susan A.; Hess, Rachel; Powell, Lynda H.; Matthews, Karen A.

2010-01-01

Objective Emerging evidence suggests associations between menopausal hot flashes and cardiovascular risk. Whether hot flashes are associated with intima media thickness (IMT) or IMT changes over time is unknown. We hypothesized that reported hot flashes would be associated with greater IMT cross-sectionally and with greater IMT progression over two years. Methods Participants were 432 women ages 45-58 at baseline participating in SWAN Heart, an ancillary study to the Study of Women's Health Across the Nation. Measures at the SWAN Heart baseline and follow-up visit two years later included a carotid artery ultrasound, reported hot flashes (past two weeks: none, 1-5, ≥6 days), and a blood sample for measurement of estradiol. Results Women reporting hot flashes ≥6 days in the prior two weeks had significantly higher IMT than women without hot flashes at baseline (mean difference(SE), mm =0.02(0.01), p=0.03) and follow-up (mean difference(SE), mm =0.02(0.01), p=0.04) visits, controlling for demographic factors and cardiovascular risk factors. Reporting hot flashes at both study visits was associated with higher follow-up IMT relative to reporting hot flashes at neither visit (mean difference(SE), mm=0.03(0.01), p=0.03). Associations between hot flashes and IMT largely remained after adjusting for estradiol. An interaction between hot flashes and obesity status was observed (p=0.05) such that relations between hot flashes and IMT were observed principally among overweight/obese women. Hot flashes were not associated with IMT progression. Conclusions These findings provided some indication that women reporting hot flashes ≥6 days in the prior two weeks may have higher IMT than women without hot flashes, particularly for women who are overweight or obese. Further work should determine whether hot flashes mark adverse underlying vascular changes. PMID:21242820

50 CFR 600.730 - Facilitation of enforcement.

Code of Federal Regulations, 2011 CFR

2011-10-01

... transmitted by flashing light directed at the vessel signaled. USCG units will normally use the flashing light... your vessel instantly.” (Period (.) means a short flash of light; dash (-) means a long flash of light... authorized officer using loudhailer, radiotelephone, flashing light signal, or other means constitutes prima...

50 CFR 600.730 - Facilitation of enforcement.

Code of Federal Regulations, 2010 CFR

2010-10-01

... transmitted by flashing light directed at the vessel signaled. USCG units will normally use the flashing light... your vessel instantly.” (Period (.) means a short flash of light; dash (-) means a long flash of light... authorized officer using loudhailer, radiotelephone, flashing light signal, or other means constitutes prima...

Brine evolution and mineral deposition in hydrologically open evaporite basins

USGS Publications Warehouse

Sanford, W.E.; Wood, W.W.

1991-01-01

A lumped-parameter, solute mass-balance model is developed to define the role of water outflow from a well-mixed basin. A mass-balance model is analyzed with a geochemical model designed for waters with high ionic strengths. Two typical waters, seawater and a Na-HCO3 ground water, are analyzed to illustrate the control that the leakage ratio (or hydrologic openness of the basin) has on brine evolution and the suite and thicknesses of evaporite minerals deposited. The analysis suggests that brines evolve differently under different leakage conditions. -from Authors

Temporary Urine and Brine Stowage System (TUBSS) Materials Selection and Testing

NASA Technical Reports Server (NTRS)

Carrigan, Caitlin; Dries, Kevin; Pensinger, Stuart

2011-01-01

Storing wastewater in the event of a system anomaly is a necessity for closed loop water recovery systems. The temporary urine and brine stowage system (TUBSS) is an assembly used to store and transfer pre-treated urine (PTU) and brine for processing or disposal at a later date. This paper describes the selection and testing of several candidate materials from both a chemical and material strength standpoint. In addition, this paper will provide results of testing as well as lessons learned from the project, culminating in the successful launch of the hardware.

Phase Equilibria of the Brine Systems Containing Strontium and Calcium Ions

NASA Astrophysics Data System (ADS)

Wang, Xia; Zhao, Kaiyu; Li, Long; Guo, Yafei; Meng, Lingzong; Deng, Tianlong

2017-12-01

It is well known that the comprehensive utilization of the Salt Lake resources successfully must be guided corresponding to the aqueous phase equilibria and phase diagrams. Researches on the phase relationships of brine systems containing calcium and strontium ions are essential to promote the development for the relative resources discovered in China at recent years. In this paper, the phase equilibria of calcium-containing systems, strontium-containing systems and calcium-strontium coexisted brine systems around the world were reviewed. The problems existed recently and new trends in future were point out.

The brine shrimp ( Artemia parthenogenetica) as encapsulation organism for prophylactic chemotherapy of fish and prawn

NASA Astrophysics Data System (ADS)

Cao, Ji-Xiang; Bian, Bo-Zhong; Li, Ming-Ren

1996-06-01

Brine shrimp ( Artemia parthenogenetica) which had ingested three water-insoluble antibacterial drugs i.e. sulfadiazine(SD), oxytetracycline (OTC) and erythromycin estolate (ERY-Es) were fed to Tilapia and Mysis III of Penaeus orientalis K. The drug contents in the predators were then determined. After administration of drugs to Tilapia and Mysis III, through the bio-encapsulation of the brine shrimp, efficacious therapeutical concentration of OTC and ERY-Es (but not SD) in the predators could be reached and maintained for more than 8 hours.

REE Sorption Study for Media #1 and Media #2 in Brine #1 and #2 at different Liquid to Solid Ratio's at Ambient Temperature

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gary Garland

This data set shows the different loading capacities of Media #1 and Media #2 in a high and low salt content brine matrix at different liquid to solid ratio's. These data sets are shaker bath tests on media #1 and media #2 in brine's #1 and #2 at 500mL-.5g(1000-1 ratio), 150mL-.75g(200-1 ratio), and 150mL-2.5g(60-1 ratio) at ambient temperature.

Assessment of Brine Management for Geologic Carbon Sequestration

DOE Office of Scientific and Technical Information (OSTI.GOV)

Breunig, Hanna M.; Birkholzer, Jens T.; Borgia, Andrea

2013-06-13

Geologic carbon sequestration (GCS) is the injection of carbon dioxide (CO 2), typically captured from stationary emission sources, into deep geologic formations to prevent its entry into the atmosphere. Active pilot facilities run by regional United States (US) carbon sequestration partnerships inject on the order of one million metric tonnes (mt) CO 2 annually while the US electric power sector emits over 2000 million mt-CO 2 annually. GCS is likely to play an increasing role in US carbon mitigation initiatives, but scaling up GCS poses several challenges. Injecting CO 2 into sedimentary basins raises fluid pressure in the pore space,more » which is typically already occupied by naturally occurring, or native, brine. The resulting elevated pore pressures increase the likelihood of induced seismicity, of brine or CO 2 escaping into potable groundwater resources, and of CO 2 escaping into the atmosphere. Brine extraction is one method for pressure management, in which brine in the injection formation is brought to the surface through extraction wells. Removal of the brine makes room for the CO 2 and decreases pressurization. Although the technology required for brine extraction is mature, this form of pressure management will only be applicable if there are cost-­effective and sustainable methods of disposing of the extracted brine. Brine extraction, treatment, and disposal may increase the already substantial capital, energy, and water demands of Carbon dioxide Capture and Sequestration (CCS). But, regionally specific brine management strategies may be able to treat the extracted water as a source of revenue, energy, and water to subsidize CCS costs, while minimizing environmental impacts. By this approach, value from the extracted water would be recovered before disposing of any resulting byproducts. Until a price is placed on carbon, we expect that utilities and other CO 2 sources will be reluctant to invest in capital intensive, high risk GCS projects; early technical, economic, and environmental assessments of brine management are extremely valuable for determining the potential role of GCS in the US. We performed a first order feasibility and economic assessment, at three different locations in the US, of twelve GCS extracted-­water management options, including: geothermal energy extraction, desalination, salt and mineral harvesting, rare-­earth element harvesting, aquaculture, algae biodiesel production, road de-­icing, enhanced geothermal system (EGS) recharge, underground reinjection, landfill disposal, ocean disposal, and evaporation pond disposal. Three saline aquifers from different regions of the US were selected as hypothetical GCS project sites to encompass variation in parameters that are relevant to the feasibility and economics of brine disposal. The three aquifers are the southern Mt. Simon Sandstone Formation in the Illinois Basin, IL; the Vedder Formation in the southern San Joaquin Basin, CA; and the Jasper Interval in the eastern Texas Gulf Basin, TX. These aquifers are candidates for GCS due to their physical characteristics and their close proximity to large CO 2 emission sources. Feasibility and impacts were calculated using one mt-­CO 2 injected as the functional unit of brine management. Scenarios were performed for typical 1000MW coal-­fired power plants (CFPP) that incurred an assumed 24 percent carbon capture energy penalty (EP), injected 90 percent of CO 2 emissions (~9 million mt-­ CO 2 injected annually), and treated extracted water onsite. Net present value (NPV), land requirements, laws and regulations, and technological limits were determined for each stage of disposal, and used to estimate feasibility. The boundary of the assessment began once extracted water was brought to the surface, and ended once the water evaporated, was injected underground, or was discharged into surface water bodies. Results of the assessment were generated, stored, and analyzed using Microsoft Excel spreadsheets and ESRI Geographical Information System (GIS) maps. Conclusions about the relative benefits and impacts of alternative brine-­management strategies were highly sensitive to local climate and weather, and aquifer water chemistry. The NPV of certain scenarios ranged from -­$50/mt-­CO 2 (a cost) to +$10/mt-­CO 2 (revenue). The land footprint of the scenarios in this study ranged from <1 km 2 to 100 km 2. Brine extraction as a pressure management tool for GCS has potential for improving the economics and for minimizing the environmental impacts of CCS. In order to maximize this potential, careful analysis of each saline aquifer and region must be conducted to determine a regionally appropriate brine use sequence (BUS) at the time of site selection. Models that use GIS will be essential tools in determining such sequences for individual CFPP. Future studies that perform risk and life cycle assessments (LCA) of BUS scenarios, incorporate additional impact metrics into the BUS model, and enhance the temporal sensitivity of the model would improve the robustness of this regional assessment method.« less

Geochemical Evidence for Possible Natural Migration of Marcellus Formation Brine to Shallow Aquifers in Pennsylvania

NASA Astrophysics Data System (ADS)

Warner, N. R.; Darrah, T. H.; Jackson, R. B.; Osborn, S.; Down, A.; Vengosh, A.

2012-12-01

The acceleration in production of natural gas from shale formations through horizontal drilling and hydraulic fracturing has altered the landscape of domestic energy production in the USA. Yet shale gas exploration has generated an increased awareness of risks to drinking water quality amid concerns for the possible migration of stray gas or hydraulic fracturing fluid and/or flowback brine to shallow drinking water aquifers. The degree to which shallow drinking water is at risk from hydraulic fracturing could depend upon the hydraulic connectivity between the shale gas formations and the surface. In this study, we analyzed the geochemistry of over 400 water samples located across six counties of northeastern Pennsylvania in the three principle aquifers, two Upper Devonian Age bedrock aquifers (Catskill and Lock Haven) and one Quaternary Age (Alluvium) that overlie the Marcellus Formation. Based on a detailed analysis of major (Br, Cl, Na, Mg, Ba, and Sr) and trace (Li) element geochemistry, coupled with utilization of a specific spectrum of isotopic tracers (87Sr/86Sr, 228Ra/ 226Ra, 2H/H, 18O/16O), we identify a salinized (Cl> 20 mg/L) shallow groundwater type which suggests conservative mixing relationships between fresh shallow groundwater and an underlying brine. Identification of the brine source is complicated as many of the brines in the northern Appalachian Basin likely share a common origin as the expelled remnants of the formation of the Silurian Salina evaporate deposits. To determine the ultimate source of the diluted brine we compared the observed geochemistry to over 80 brines produced from northern Appalachian Basin formations. The shallow salinized groundwater most closely resembles diluted produced water from the Middle Devonian Marcellus Formation. The 18O/16O and 2H/H of the salinized groundwater indicate that the brine is likely diluted with post-glacial (<10,000 ybp) meteoric water. Combined, these data indicate that hydraulic connections allowed cross formational migration of brine from deeper formations (1-2 kilometers below ground surface) and subsequent dilution. The occurrence of the saline water does not appear to be correlated with the location of shale-gas wells. Also, salinized groundwater with similar major element chemistry was reported prior to the most recent shale-gas development in the region. The source of the salinized water is likely not the recent drilling and hydraulic fracturing; instead brine migrated into the shallow aquifers and was recently diluted through natural pathways and processes. However, the presence of natural hydraulic connections to deeper formations suggests specific structural and hydrodynamic regimes in northeastern Pennsylvania where shallow drinking water resources are at greater risk of contamination, particularly with fugitive gases, during drilling and hydraulic fracturing of shale gas. The severity of the risk could depend upon the presence of pathways that allow the migration of fluids into the shallow aquifers on human time scales.

Experimental evaporation of hyperacid brines: Effects on chemical composition and chlorine isotope fractionation

NASA Astrophysics Data System (ADS)

Rodríguez, Alejandro; van Bergen, Manfred J.; Eggenkamp, H. G. M.

2018-02-01

Hyperacid brines from active volcanic lakes are some of the chemically most complex aqueous solutions on Earth. Their compositions provide valuable insights into processes of elemental transfer from a magma body to the surface and interactions with solid rocks and the atmosphere. This paper describes changes in chemical and δ37Cl signatures observed in a 1750 h isothermal evaporation experiment on hyperacid (pH 0.1) sulphate-chloride brine water from the active lake of Kawah Ijen volcano (Indonesia). Although gypsum was the only evaporite mineral identified in the evolving brine, decreasing Si concentrations may ultimately result in amorphous silica precipitation. Geochemical simulations predict the additional formation of elemental sulphur at lower water activities (aH2O ≤ 0.65) that were not reached in the experiment. Absence of other sulphates and halides despite the high load of dissolved elements (initial TDS ca. 100 g/kg) can be attributed to increased solubility of metals, promoted by extensive formation of complexes between the variety of cations and the major anions (HSO4-, Cl-, F-) present. Chlorine deviations from a conservative behaviour point to losses of gaseous hydrogen chloride (HCl(g)) and consequently an increase in Br/Cl ratios. Chlorine isotope fractionation that accompanied the escape of HCl(g) showed a marked change in sign and magnitude in the course of progressive evaporation of the brine. The calculated factor of fractionation between HCl(g) and dissolved Cl for the initial interval (before 500 h) is positive (1000lnαHCl(g)-Cldiss. = + 1.55 ± 0.49‰to + 3.37 ± 1.11‰), indicating that, at first, the escaping HCl(g) was isotopically heavier than the dissolved Cl remaining in the brine. Conversely, fractionation shifted to the opposite direction in the subsequent interval (1000lnαHCl(g)-Cldiss. = 5.67 ± 0.17‰to - 5.64 ± 0.08‰), in agreement with values reported in literature. It is proposed that Cl isotopic fractionation in highly acidic brines is controlled by the distribution of dissolved chlorine species, which changes from Cl- to HClo dominance with the progressive pH decline. The Kawah Ijen lake acquired its extreme composition through influx of sulphur and halogen-rich magmatic gas components and extensive rock dissolution. If hyperacid brines with comparable chemical composition existed on Mars, evaporation processes up to the extent reported here (aH2O = 0.85), were likely accompanied by losses of gaseous HCl. The resulting changes in Cl isotope compositions, Br/Cl, S/Cl and other ratios in the residual brine might be potentially recorded in assemblages of halogen-bearing secondary evaporation minerals. Also, volcanic-hydrothermal brines as these would extend the stability of liquid water on the Martian surface down to a temperature of -90 °C.

Halite Brine in the Onondaga Trough near Syracuse, New York: Characterization and Simulation of Variable-Density Flow

USGS Publications Warehouse

Yager, Richard M.; Kappel, William M.; Plummer, Niel

2007-01-01

Halite brine (saturation ranging from 45 to 80 percent) lies within glacial-drift deposits that fill the Onondaga Trough, a 40-km long bedrock valley deepened by Pleistocene ice near Syracuse, N.Y. The most concentrated brine occupies the northern end of the trough, more than 15 kilometers (km) beyond the northern limit of halite beds in the Silurian Salina Group, the assumed source of salt. The chemical composition of the brine and its radiocarbon age estimated from geochemical modeling with NETPATH suggest that the brine formed through dissolution of halite by glacial melt water, and later mixed with saline bedrock water about 16,500 years ago. Transient variable-density flow simulations were conducted with SEAWAT to assess current (2005) ground-water flow conditions within the glacial drift. A transient three-dimensional (3D) model using a grid spacing of 100 meters (m) and maximum layer spacing of 30 m was used to simulate a 215-year period from 1790 to 2005. The model was calibrated to observations of water levels, chloride concentrations, and discharges of water and chloride. The model produced an acceptable match to the measured data and provided a reasonable representation of the density distribution within the brine pool. The simulated mass of chloride in storage declined steadily during the 215-year period; however, the decline was mainly due to dispersion, which is probably overestimated because of the large layer spacing. Model results suggest that saline water from waste-disposal operations associated with a chemical plant has migrated beneath the western shore of Onondaga Lake. Two-dimensional (2D) cross-sectional models of the aquifer system within the Onondaga Trough were prepared to test the plausibility of a hypothesis that the brine was derived from a relict source of halite that was dissolved by glacial melt water. The 2D models used parameter estimates obtained with the calibrated 3D model. Model results indicated the brine could have migrated from the bedded-halite subcrop area and remained in the glacial sediments at the northern end of trough for over 16,000 years, as suggested by radiocarbon dating. The 2D models also indicated that slow dissipation of brine occurs through a mixing zone formed by upward flow of freshwater over the southern end of the brine pool. The simulated depletion rate is controlled by the rate of mixing, which is limited by the specified grid resolution and the accuracy of the numerical method used to solve the advection-dispersion equation. A numerical solution obtained by using an implicit finite-difference method with upstream weighting and a 2D grid containing a column and layer spacing of 76 m and 3 m, respectively, provided an acceptable match to chloride concentration profiles measured at three locations within the Onondaga Trough.

49 CFR 234.217 - Flashing light units.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 4 2010-10-01 2010-10-01 false Flashing light units. 234.217 Section 234.217..., Inspection, and Testing Maintenance Standards § 234.217 Flashing light units. (a) Each flashing light unit.... (b) Each flashing light unit shall be maintained to prevent dust and moisture from entering the...

49 CFR 234.217 - Flashing light units.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 49 Transportation 4 2011-10-01 2011-10-01 false Flashing light units. 234.217 Section 234.217..., Inspection, and Testing Maintenance Standards § 234.217 Flashing light units. (a) Each flashing light unit.... (b) Each flashing light unit shall be maintained to prevent dust and moisture from entering the...

Lunar Impact Flash Locations

NASA Technical Reports Server (NTRS)

Moser, D. E.; Suggs, R. M.; Kupferschmidt, L.; Feldman, J.

2015-01-01

A bright impact flash detected by the NASA Lunar Impact Monitoring Program in March 2013 brought into focus the importance of determining the impact flash location. A process for locating the impact flash, and presumably its associated crater, was developed using commercially available software tools. The process was successfully applied to the March 2013 impact flash and put into production on an additional 300 impact flashes. The goal today: provide a description of the geolocation technique developed.

Distinguishing seawater from geologic brine in saline coastal groundwater using radium-226; an example from the Sabkha of the UAE

USGS Publications Warehouse

Kraemer, Thomas F.; Wood, Warren W.; Sanford, Ward E.

2014-01-01

Sabkhat (Salt flats) are common geographic features of low-lying marine coastal areas that develop under hyper-arid climatic conditions. They are characterized by the presence of highly concentrated saline solutions and evaporitic minerals, and have been cited in the geologic literature as present-day representations of hyper-arid regional paleohydrogeology, paleoclimatology, coastal processes, and sedimentation in the geologic record. It is therefore important that a correct understanding of the origin and development of these features be achieved. Knowledge of the source of solutes is an important first step in understanding these features. Historically, two theories have been advanced as to the main source of solutes in sabkha brines: an early concept entailing seawater as the obvious source, and a more recent and dynamic theory involving ascending geologic brine forced upward into the base of the sabkha by a regional hydraulic gradient in the underlying formations. Ra-226 could uniquely distinguish between these sources under certain circumstances, as it is typically present at elevated activity of hundreds to thousands of Bq/m3 (Becquerels per cubic meter) in subsurface formation brines; at exceedingly low activities in open ocean and coastal water; and not significantly supplied to water from recently formed marine sedimentary framework material. The coastal marine sabkha of the Emirate of Abu Dhabi was used to test this hypothesis. The distribution of Ra-226 in 70 samples of sabkha brine (mean: 700 Bq/m3), 7 samples of underlying deeper formation brine (mean: 3416 Bq/m3), the estimated value of seawater (< 16 Bq/m3) and an estimate of supply from sabkha sedimentary framework grains (<~6 Bq/m3) provide the first direct evidence that ascending geologic brine contributes significantly to the solutes of this sabkha system.

Wind effects on prey availability: How northward migrating waders use brackish and hypersaline lagoons in the sivash, Ukraine

NASA Astrophysics Data System (ADS)

Verkuil, Yvonne; Koolhaas, Anita; Van Der Winden, Jan

Large numbers of waders migrating northward in spring use the Sivash, a large system of shallow, brackish and hypersaline lagoons in the Black Sea and Azov Sea region (Ukraine). The bottoms of these lagoons are often uncovered by the wind. Hence, for waders the time and space available for feeding depend on wind conditions. In hypersaline lagoons the benthic and pelagic fauna was very poor, consisting mainly of chironomid larvae (0.19 g AFDM·m -2) and brine shrimps Artemia salina, respectively. Brine shrimp abundance was correlated with salinity, wind force, wind direction and water depth. Dunlin Calidris alpina and curlew sandpiper Calidris ferruginea were the only species feeding on brine shrimp. As brine shrimp densities are higher in deeper water, smaller waders such as broad-billed sandpipers Limicola falcinellus are too short-legged to reach exploitable densities of brine shrimp. In brackish lagoons the benthic and pelagic fauna was rich, consisting of polychaetes, bivalves, gastropods, chironomid larvae, isopods and amphipods (8.9 to 30.5 g AFDM·m -2), but there were no brine shrimps. Prey biomass increased with the distance from the coast, being highest on the site that was most frequently inundated. Dunlin, broad-billed sandpiper and grey plover Pluvialis squatarola were the most abundant birds in the brackish lagoon. Due to the effects of wind-tides only a small area was usually available as a feeding site. Gammarus insensibilis was the alternative prey resource in the water layer, and their density varied with wind direction in the same way as brine shrimp. Curlew sandpipers and dunlins in the hypersaline lagoons and broad-billed sandpipers in the brackish lagoons often changed feeding sites, probably following the variation in prey availability. Only because of the large size and variety of lagoons are waders in the Sivash always able to find good feeding sites.

Effects of high salinity wastewater discharges on unionid mussels in the Allegheny River, Pennsylvania

USGS Publications Warehouse

Kathleen Patnode,; Hittle, Elizabeth A.; Robert Anderson,; Lora Zimmerman,; Fulton, John W.

2015-01-01

We examined the effect of high salinity wastewater (brine) from oil and natural gas drilling on freshwater mussels in the Allegheny River, Pennsylvania, during 2012. Mussel cages (N = 5 per site) were deployed at two sites upstream and four sites downstream of a brine treatment facility on the Allegheny River. Each cage contained 20 juvenile northern riffleshell mussels Epioblasma torulosa rangiana). Continuous specific conductance and temperature data were recorded by water quality probes deployed at each site. To measure the amount of mixing throughout the entire study area, specific conductance surveys were completed two times during low-flow conditions along transects from bank to bank that targeted upstream (reference) reaches, a municipal wastewater treatment plant discharge upstream of the brine-facility discharge, the brine facility, and downstream reaches. Specific conductance data indicated that high specific conductance water from the brine facility (4,000–12,000 µS/cm; mean 7,846) compared to the reference reach (103–188 µS/cm; mean 151) is carried along the left descending bank of the river and that dilution of the discharge via mixing does not occur until 0.5 mi (805 m) downstream. Juvenile northern riffleshell mussel survival was severely impaired within the high specific conductance zone (2 and 34% at and downstream of the brine facility, respectively) and at the municipal wastewater treatment plant (21%) compared to background (84%). We surveyed native mussels (family Unionidae) at 10 transects: 3 upstream, 3 within, and 4 downstream of the high specific conductance zone. Unionid mussel abundance and diversity were lower for all transects within and downstream of the high conductivity zone compared to upstream. The results of this study clearly demonstrate in situ toxicity to juvenile northern riffleshell mussels, a federally endangered species, and to the native unionid mussel assemblage located downstream of a brine discharge to the Allegheny River.

Detecting a liquid and solid H2O layer by geophysical methods

NASA Astrophysics Data System (ADS)

Yoshikawa, K.; Romanovsky, V.; Tsapin, A.; Brown, J.

2002-12-01

The objective is to detect the hydrological and cryological structure of the cold continuous permafrost subsurface using geophysical methods. We believe that a lot of water potentially exists as solid and liquid phases underground on Mars. It is likely that the liquid fluid would be high in saline concentration (brine). The ground freezing process involves many hydrological processes including enrichment of the brine layer. The brine layer is an important environment for ancient and/or current life to exist on terrestrial permafrost regions. The existence of a Martian brine layer would increase the possibility of the existence of life, as on Earth. In situ electric resistivity measurement will be the most efficient method to determine brine layer as well as massive H2O ice in the permafrost. However, the wiring configuration is unlikely to operate on the remote planetary surface. Satellite-born Radar and/or EM methods will be the most accessible methods for detecting the hydrological and cryological structure. We are testing several geophysical methods at the brine layer site in Barrow and massive pingo ice site in Fairbanks, Alaska. The radar system is affected by the dielectric properties of subsurface materials, which allows for evidence of liquid phase in the frozen ground. The dielectric constant varies greatly between liquid water and frozen ground. The depth of the terrestrial (and probably Martian) brine layer is frequently located deeper than the maximum detecting depth of the impulse type of the ground penetrating radar system. Once we develop a radar system with a deeper penetrating capability (Lower frequency), the dispersion of the ground ice will be the key function for interpretation of these signals. We will improve and use radar signals to understand the hydrological and cryological structure in the permafrost. The core samples and borehole temperature data validate these radar signals.

Concentrated sodium chloride brine solutions as an additional treatment for preventing the introduction of nonindigenous species in the ballast tanks of ships declaring no ballast on board.

PubMed

Santagata, Scott; Bacela, Karolina; Reid, David F; Mclean, Kevin A; Cohen, Jill S; Cordell, Jeffery R; Brown, Christopher W; Johengen, Thomas H; Ruiz, Gregory M

2009-02-01

Currently, seawater flushing is the only management strategy for reducing the number of viable organisms in residual sediments and water of ballast tanks of vessels declaring no ballast on board (NOBOB) that traffic ports of the eastern United States. Previously, we identified several species of freshwater and brackish-water peracarid crustaceans able to survive the osmotic shock that occurs during open-ocean ballast water exchange and, potentially, to disperse over long distances via ballasted ships and NOBOB vessels. We tested the efficacy of concentrated sodium chloride brine solutions as an additional treatment for eradicating the halotolerant taxa often present in the ballast tanks of NOBOB ships. The lowest brine treatments (30 ppt for 1 h) caused 100% mortality in several species of cladocerans and copepods collected from oligohaline habitats. Several brackish-water peracarid crustaceans, however, including some that can survive in freshwater as well, required higher brine concentrations and longer exposure durations (45-60 ppt for 3-24 h). The most resilient animals were widely introduced peracarid crustaceans that generally prefer mesohaline habitats but do not tolerate freshwater (required brine treatments of 60-110 ppt for 3-24 h). Brine treatments (30 ppt) also required less time to cause 100% mortality for eight taxa compared with treatments using 34 ppt seawater. Based on these experiments and published data, we present treatment strategies for the ballast tank biota often associated with NOBOB vessels entering the Great Lakes region. We estimate the lethal dosage of brine for 95% of the species in our experiments to be 110 ppt (95% confidence interval, 85-192 ppt) when the exposure time is 1 h and 60 ppt (95% confidence interval, 48-98 ppt) when the exposure duration is 6 h or longer.

Fate of Pathogenic Bacteria Associated with Production of Pickled Sausage by Using a Cold Fill Process.

PubMed

Gaydos, Nelson J; Cutter, Catherine N; Campbell, Jonathan A

2016-10-01

Preservation by pickling has been used for many years to extend the shelf life of various types of food products. By storing meat products in a brine solution containing an organic acid, salt, spices, as well as other preservatives, the pH of the product is reduced, thus increasing the safety and shelf life of the product. Pickling may involve the use of heated brines to further add to the safety of the food product. When precooked, ready-to-eat (RTE) sausages are pickled with a heated brine solution, the process is referred to as hot filling. However, hot filling has been shown to affect the clarity of the brine, making the product cloudy and unappealing to consumers. Because of the potential quality defects caused by higher temperatures associated with hot fill pickling, cold fill pickling, which uses room temperature brine, is preferred by some pickled sausage manufacturers. Because little information exists on the safety of cold fill, pickled sausages, a challenge study was designed using a brine solution (5% acetic acid and 5% salt at 25°C) to pickle precooked, RTE sausages inoculated with a pathogen cocktail consisting of Salmonella Typhimurium, Salmonella Senftenberg, Salmonella Montevideo, Listeria monocytogenes , and Staphylococcus aureus . All pathogens were reduced ~6.80 log CFU/g in 72 h when enumerated on nonselective media. On selective media, Salmonella and L. monocytogenes decreased 6.33 and 6.35 log CFU/g in 12 h, respectively whereas S. aureus was reduced 6.80 log CFU/g in 24 h. Sausages experienced significant (P ≤ 0.05) decreases in pH over the 28 days of storage, whereas no significant differences were observed in water activity (P =0.1291) or salt concentration of the sausages (P =0.1445) or brine (P =0.3180). The results of this experiment demonstrate that cold fill pickling can effectively reduce and inhibit bacterial pathogens.

Widespread legacy brine contamination from oil production reduces survival of chorus frog larvae

USGS Publications Warehouse

Hossack, Blake R.; Puglis, Holly J.; Battaglin, William A.; Anderson, Chauncey; Honeycutt, Richard; Smalling, Kelly

2017-01-01

Advances in drilling techniques have facilitated a rapid increase in hydrocarbon extraction from energy shales, including the Williston Basin in central North America. This area overlaps with the Prairie Pothole Region, a region densely populated with wetlands that provide numerous ecosystem services. Historical (legacy) disposal practices often released saline co-produced waters (brines) with high chloride concentrations, affecting wetland water quality directly or persisting in sediments. Despite the potential threat of brine contamination to aquatic habitats, there has been little research into its ecological effects. We capitalized on a gradient of legacy brine-contaminated wetlands in northeast Montana to conduct laboratory experiments to assess variation in survival of larval Boreal Chorus Frogs (Pseudacris maculata) reared on sediments from 3 local wetlands and a control source. To help provide environmental context for the experiment, we also measured chloride concentrations in 6 brine-contaminated wetlands in our study area, including the 2 contaminated sites used for sediment exposures. Survival of frog larvae during 46- and 55-day experiments differed by up to 88% among sediment sources (Site Model) and was negatively correlated with potential chloride exposure (Chloride Model). Five of the 6 contaminated wetlands exceeded the U.S. EPA acute benchmark for chloride in freshwater (860 mg/L) and all exceeded the chronic benchmark (230 mg/L). However, the Wetland Site model explained more variation in survival than the Chloride Model, suggesting that chloride concentration alone does not fully reflect the threat of contamination to aquatic species. Because the profiles of brine-contaminated sediments are complex, further surveys and experiments are needed across a broad range of conditions, especially where restoration or remediation actions have reduced brine-contamination. Information provided by this study can help quantify potential ecological threats and help land managers prioritize conservation strategies as part of responsible and sustainable energy development.

Constraints on evaporation and dilution of terminal, hypersaline lakes under negative water balance: The Dead Sea, Israel

NASA Astrophysics Data System (ADS)

Zilberman, Tami; Gavrieli, Ittai; Yechieli, Yoseph; Gertman, Isaac; Katz, Amitai

2017-11-01

The response of hypersaline terminal lakes to negative water balance was investigated by studying brines evaporating to extreme salinities in sinkholes along the western coast of the Dead Sea and during on-site evaporation experiments of the Dead Sea brine. Density and temperature were determined in the field and all samples were analyzed for their major and a few minor solutes. The activity of H2O (aH2O) in the brines was calculated, and the degree of evaporation (DE) was established using Sr2+as a conservative solute. The relations between density and water activity were obtained by polynomial regression, and the relation between the lake's volume and level was established using Hall's (1996) hypsographic model for the Dead Sea basin. Relating the results to the modern, long-term relative humidity (RH) over the basin shows that (a) The lowermost attainable level of a terminal lake undergoing evaporation with no inflow is dictated by the median RH; this level represents equilibrium between the brine's aH2O and RH; (b) Small, saline water bodies with high surface to volume ratios (A/V), such as the hypersaline brines in the sinkholes, are very sensitive to short term changes in RH; in these, the brines' aH2O closely follows the seasonal changes; (c) the level decline of the Dead Sea due to evaporation under present climatic conditions and assuming no inflow to the lake may continue down to 516-537 m below mean sea level (bmsl), corresponding to a water activity range of 0.46-0.39 in its brine, in equilibrium with the overlying relative air humidity; this suggests that the lake level cannot drop more than ∼100 m from its present level; and (d) The maximum RH values that existed over the precursor lake of the Dead Sea (Lake Lisan) during geologically reconstructed minima levels can be similarly calculated.

FLASH Interface; a GUI for managing runtime parameters in FLASH simulations

NASA Astrophysics Data System (ADS)

Walker, Christopher; Tzeferacos, Petros; Weide, Klaus; Lamb, Donald; Flocke, Norbert; Feister, Scott

2017-10-01

We present FLASH Interface, a novel graphical user interface (GUI) for managing runtime parameters in simulations performed with the FLASH code. FLASH Interface supports full text search of available parameters; provides descriptions of each parameter's role and function; allows for the filtering of parameters based on categories; performs input validation; and maintains all comments and non-parameter information already present in existing parameter files. The GUI can be used to edit existing parameter files or generate new ones. FLASH Interface is open source and was implemented with the Electron framework, making it available on Mac OSX, Windows, and Linux operating systems. The new interface lowers the entry barrier for new FLASH users and provides an easy-to-use tool for experienced FLASH simulators. U.S. Department of Energy (DOE), NNSA ASC/Alliances Center for Astrophysical Thermonuclear Flashes, U.S. DOE NNSA ASC through the Argonne Institute for Computing in Science, U.S. National Science Foundation.

OTD Observations of Continental US Ground and Cloud Flashes

NASA Technical Reports Server (NTRS)

Koshak, William

2007-01-01

Lightning optical flash parameters (e.g., radiance, area, duration, number of optical groups, and number of optical events) derived from almost five years of Optical Transient Detector (OTD) data are analyzed. Hundreds of thousands of OTD flashes occurring over the continental US are categorized according to flash type (ground or cloud flash) using US National Lightning Detection Network TM (NLDN) data. The statistics of the optical characteristics of the ground and cloud flashes are inter-compared on an overall basis, and as a function of ground flash polarity. A standard two-distribution hypothesis test is used to inter-compare the population means of a given lightning parameter for the two flash types. Given the differences in the statistics of the optical characteristics, it is suggested that statistical analyses (e.g., Bayesian Inference) of the space-based optical measurements might make it possible to successfully discriminate ground and cloud flashes a reasonable percentage of the time.

Menopausal Hot Flashes and White Matter Hyperintensities

PubMed Central

Thurston, Rebecca C.; Aizenstein, Howard J.; Derby, Carol A.; Sejdić, Ervin; Maki, Pauline M.

2015-01-01

Objective Hot flashes are the classic menopausal symptom. Emerging data links hot flashes to cardiovascular disease (CVD) risk, yet how hot flashes are related to brain health is poorly understood. We examined the relationship between hot flashes - measured via physiologic monitor and self-report - and white matter hyperintensities (WMH) among midlife women. Methods Twenty midlife women ages 40-60 without clinical CVD, with their uterus and both ovaries, and not taking hormone therapy were recruited. Women underwent 24 hours of ambulatory physiologic and diary hot flash monitoring to quantify hot flashes; magnetic resonance imaging to assess WMH burden; 72 hours of actigraphy and questionnaires to quantify sleep; and a blood draw, questionnaires, and physical measures to quantify demographics and CVD risk factors. Test of a priori hypotheses regarding relations between physiologically-monitored and self-reported wake and sleep hot flashes and WMH were conducted in linear regression models. Results More physiologically-monitored hot flashes during sleep were associated with greater WMH, controlling for age, race, and body mass index [beta(standard error)=.0002 (.0001), p=.03]. Findings persisted controlling for sleep characteristics and additional CVD risk factors. No relations were observed for self-reported hot flashes. Conclusions More physiologically-monitored hot flashes during sleep were associated with greater WMH burden among midlife women free of clinical CVD. Results suggest that relations between hot flashes and CVD risk observed in the periphery may extend to the brain. Future work should consider the unique role of sleep hot flashes in brain health. PMID:26057822

Some properties of negative cloud-to-ground flashes from observations of a local thunderstorm based on accurate-stroke-count studies

NASA Astrophysics Data System (ADS)

Zhu, Baoyou; Ma, Ming; Xu, Weiwei; Ma, Dong

2015-12-01

Properties of negative cloud-to-ground (CG) lightning flashes, in terms of number of strokes per flash, inter-stroke intervals and the relative intensity of subsequent and first strokes, were presented by accurate-stroke-count studies based on all 1085 negative flashes from a local thunderstorm. The percentage of single-stroke flashes and stroke multiplicity evolved significantly during the whole life cycle of the study thunderstorm. The occurrence probability of negative CG flashes decreased exponentially with the increasing number of strokes per flash. About 30.5% of negative CG flashes contained only one stroke and number of strokes per flash averaged 3.3. In a subset of 753 negative multiple-stroke flashes, about 41.4% contained at least one subsequent stroke stronger than the corresponding first stroke. Subsequent strokes tended to decrease in strength with their orders and the ratio of subsequent to first stroke peaks presented a geometric mean value of 0.52. Interestingly, negative CG flashes of higher multiplicity tended to have stronger initial strokes. 2525 inter-stroke intervals showed a more or less log-normal distribution and gave a geometric mean value of 62 ms. For CG flashes of particular multiplicity geometric mean inter-stroke intervals tended to decrease with the increasing number of strokes per flash, while those intervals associated with higher order strokes tended to be larger than those associated with low order strokes.

Effect of Escitalopram on Hot Flash Interference: A Randomized, Controlled Trial

PubMed Central

Carpenter, Janet S.; Guthrie, Katherine A.; Larson, Joseph C.; Freeman, Ellen W.; Joffe, Hadine; Reed, Susan D.; Ensrud, Kristine E.; LaCroix, Andrea Z.

2012-01-01

Objectives To estimate the effect of escitalopram 10–20 mg/day versus placebo for reducing hot flash interference in daily life and understand correlates and predictors of reductions in hot flash interference, a key measure of quality of life. Design Multi-site, randomized, double-blind, placebo-controlled clinical trial. Patients 205 midlife women (46% African-American) who met criteria participated. Setting MsFLASH clinical sites in Boston, Indianapolis, Oakland, and Philadelphia. Intervention After baseline, women were randomized to 1 pill of escitalopram 10 mg/day (n=104) or placebo (n=101) with follow-up at 4- and 8-weeks. At week 4, those not achieving 50% fewer hot flashes were increased to 2 pills daily (20 mg/day or 2 placebo pills). Main outcome measures The Hot Flash Related Daily Interference Scale; Correlates were variables from hot flash diaries; Predictors were baseline demographics, clinical variables, depression, anxiety, sleep quality, and hot flashes. Results Compared to placebo, escitalopram significantly reduced hot flash interference by 6.0 points at week 4 and 3.4 points at week 8 more than placebo (p=0.012). Reductions in hot flash interference correlated with changes in hot flash diary variables. However, baseline variables did not significantly predict reductions in hot flash interference. Conclusions Escitalopram 10–20mg/day for 8 weeks improves women’s quality of life and this benefit did not vary by demographic, clinical, mood, sleep, or hot flash variables. PMID:22480818

Ophthalmic Evaluation in Beta-Thalassemia.

PubMed

Merchant, Rashid H; Punde, Hrishikesh; Thacker, Neepa; Bhatt, Deepak

2017-07-01

To determine the association of ocular manifestations in beta-thalassemia with the patient's age, blood transfusion requirements, average serum ferritin and dose and duration of iron chelation therapy. Sixty multi-transfused beta thalassemia patients of 12 to 18 y of age on chelation therapy were included in this cross-sectional analysis. Structural and functional evaluation of the retina was done using Optical coherence tomography (OCT) and Electroretinography (ERG), including flash ERG and Pattern ERG (PERG). Routine ophthalmic examination and B scan of the eye was also done. Flash ERG a-waves and b-waves were recorded, however only a-wave amplitude was evaluated. Pattern ERG n35, n95 and p50 waves were recorded and p50 wave amplitude was evaluated. The a-wave on flash and p50 on pattern waves represent retinal photoreceptor epithelium (RPE) photoreceptor response, which is mainly affected in beta-thalassemia. Ocular changes were detected in 38.3% and a significant correlation was noted with increase in age (p = 0.045) but not with serum ferritin, transfusion requirements or chelation therapy. Refractive errors were found in 14 cases (23%), such as myopia with astigmatism in 13 (21.7%) and only myopia in 6 subjects (10%). OCT abnormality was noted in 1 patient (1.7%) who had thinning of central retina; right eye 132 μm and left eye 146 μm (n > 200 μm). Abnormalities were noted in a-wave amplitude on flash ERG in 20% of cases, while reduced p50 amplitude on PERG was noted in 15%. A significant correlation was noted between ocular findings and increase in age, but not with serum ferritin, transfusion requirements or chelation therapy. ERG appears to be a promising tool for screening patients with beta-thalassemia and can serve as a follow-up test for evaluating retinal function.

Investigating Brine Shrimp.

ERIC Educational Resources Information Center

Duran, Lena Ballone

2003-01-01

Presents a brine shrimp activity designed for students in grades 5-12 to foster authentic scientific inquiry in addition to providing an engaging and exciting avenue for student exploration. Emphasizes that inquiry should be a critical component in the science classroom. (KHR)

53. Interior of launch support building, brine chiller, view towards ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

53. Interior of launch support building, brine chiller, view towards south - Ellsworth Air Force Base, Delta Flight, Launch Facility, On County Road T512, south of Exit 116 off I-90, Interior, Jackson County, SD

SURFACE CONTAINMENT FOR GEOTHERMAL BRINES

EPA Science Inventory

This report examines the probability of significant releases of geothermal brine to the surface environment through unplanned or accidental events. It then evaluates the containment measures that may be used to prevent environmental damage. The results indicate that major spills ...

Convective dissolution of carbon dioxide in saline aquifers

NASA Astrophysics Data System (ADS)

Neufeld, Jerome A.; Hesse, Marc A.; Riaz, Amir; Hallworth, Mark A.; Tchelepi, Hamdi A.; Huppert, Herbert E.

2010-11-01

Geological carbon dioxide (CO2) storage is a means of reducing anthropogenic emissions. Dissolution of CO2 into the brine, resulting in stable stratification, increases storage security. The dissolution rate is determined by convection in the brine driven by the increase of brine density with CO2 saturation. We present a new analogue fluid system that reproduces the convective behaviour of CO2-enriched brine. Laboratory experiments and high-resolution numerical simulations show that the convective flux scales with the Rayleigh number to the 4/5 power, in contrast with a classical linear relationship. A scaling argument for the convective flux incorporating lateral diffusion from downwelling plumes explains this nonlinear relationship for the convective flux, provides a physical picture of high Rayleigh number convection in a porous medium, and predicts the CO2 dissolution rates in CO2 accumulations. These estimates of the dissolution rate show that convective dissolution can play an important role in enhancing storage security.

Impacts of blending on dilution of negatively buoyant brine discharge in a shallow tidal sea.

PubMed

Kämpf, Jochen

2009-07-01

A fine-resolution three-dimensional hydrodynamic model is applied to study the dilution of desalination brine discharged into a tidal sea. Based on given inflow rate and salinity excess of discharge brine, this study explores variations in mid-field dilutions when other low-salinity wastewater is added to the discharge. Findings reveal that this blending leads to a decrease in dilution in the mixing zone and therefore to higher levels of pollutants in this zone, while, on the other hand, the mixing zone occupies a smaller area. The reason is that the discharge of brine creates a density-driven flow that operates to partially remove effluent from the discharge location. This removal is less efficient for the decrease in density excess of the discharge. Hence, in an ambient sea of moderate mixing, blending can be expected to increase the risk of marine pollution in the mixing zone.

Effects of a brine discharge over soft bottom Polychaeta assemblage.

PubMed

Del-Pilar-Ruso, Yoana; De-la-Ossa-Carretero, Jose Antonio; Giménez-Casalduero, Francisca; Sánchez-Lizaso, Jose Luis

2008-11-01

Desalination is a growing activity that has introduced a new impact, brine discharge, which may affect benthic communities. Although the role of polychaetes as indicators to assess organic pollution is well known, their tolerance to salinity changes has not been examined to such a great extent. The aim of this study was to examine the effect of brine discharge over soft bottom polychaete assemblage along the Alicante coast (Southeast Spain) over a two year period. Changes in the polychaete assemblage was analysed using univariate and multivariate techniques. We compared a transect in front of the discharge with two controls. At each transect we sampled at three depths (4, 10 and 15 m) during winter and summer. We have observed different sensitivity of polychaete families to brine discharges, Ampharetidae being the most sensitive, followed by Nephtyidae and Spionidae. Syllidae and Capitellidae showed some resistance initially, while Paraonidae proved to be a tolerant family.

Magnesium compounds

USGS Publications Warehouse

Kramer, D.A.

2007-01-01

Seawater and natural brines accounted for about 52 percent of U.S. magnesium compounds production in 2006. Dead-burned magnesia was produced by Martin Marietta Magnesia Specialties from well brines in Michigan. Caustic-calcined magnesia was recovered from sea-water by Premier Chemicals in Florida; from well brines in Michigan by Martin Marietta and Rohm and Haas; and from magnesite in Nevada by Premier Chemicals. Intrepid Potash-Wendover and Great Salt Lake Minerals recovered magnesium chloride brines from the Great Salt Lake in Utah. Magnesium hydroxide was produced from brucite by Applied Chemical Magnesias in Texas, from seawater by SPI Pharma in Delaware and Premier Chemicals in Florida, and by Martin Marietta and Rohm and Haas from their operations mentioned above. About 59 percent of the magnesium compounds consumed in the United States was used for refractories that are used mainly to line steelmaking furnaces. The remaining 41 percent was consumed in agricultural, chemical, construction, environmental and industrial applications.

Geochemical Impacts of Carbon Dioxide, Brine, Trace Metal and Organic Leakage into an Unconfined, Oxidizing Limestone Aquifer

DOE PAGES

Bacon, Diana H.; Dai, Zhenxue; Zheng, Liange

2014-12-31

An important risk at CO2 storage sites is the potential for groundwater quality impacts. As part of a system to assess the potential for these impacts a geochemical scaling function has been developed, based on a detailed reactive transport model of CO2 and brine leakage into an unconfined, oxidizing carbonate aquifer. Stochastic simulations varying a number of geochemical parameters were used to generate a response surface predicting the volume of aquifer that would be impacted with respect to regulated contaminants. The brine was assumed to contain several trace metals and organic contaminants. Aquifer pH and TDS were influenced by CO2more » leakage, while trace metal concentrations were most influenced by the brine concentrations rather than adsorption or desorption on calcite. Organic plume sizes were found to be strongly influenced by biodegradation.« less

The total flow concept for geothermal energy conversion

NASA Technical Reports Server (NTRS)

Austin, A. L.

1974-01-01

A geothermal development project has been initiated at the Lawrence Livermore Laboratory (LLL) to emphasize development of methods for recovery and conversion of the energy in geothermal deposits of hot brines. Temperatures of these waters vary from 150 C to more than 300 C with dissolved solids content ranging from less than 0.1% to over 25% by weight. Of particular interest are the deposits of high-temperature/high-salinity brines, as well as less saline brines, known to occur in the Salton Trough of California. Development of this resource will depend on resolution of the technical problems of brine handling, scale and precipitation control, and corrosion/erosion resistant systems for efficient conversion of thermal to electrical energy. Research experience to date has shown these problems to be severe. Hence, the LLL program emphasizes development of an entirely different approach called the Total Flow concept.

Cardiac autonomic function and hot flashes among perimenopausal and postmenopausal women.

PubMed

Gibson, Carolyn J; Mendes, Wendy Berry; Schembri, Michael; Grady, Deborah; Huang, Alison J

2017-07-01

Abnormalities in autonomic function are posited to play a pathophysiologic role in menopausal hot flashes. We examined relationships between resting cardiac autonomic activity and hot flashes in perimenopausal and postmenopausal women. Autonomic function was assessed at baseline and 12 weeks among perimenopausal and postmenopausal women (n = 121, mean age 53 years) in a randomized trial of slow-paced respiration for hot flashes. Pre-ejection period (PEP), a marker of sympathetic activation, was measured with impedance cardiography. Respiratory sinus arrhythmia (RSA), a marker of parasympathetic activation, was measured with electrocardiography. Participants self-reported hot flash frequency and severity in 7-day symptom diaries. Analysis of covariance models were used to relate autonomic function and hot flash frequency and severity at baseline, and to relate changes in autonomic function to changes in hot flash frequency and severity over 12 weeks, adjusting for age, body mass index, and intervention assignment. PEP was not associated with hot flash frequency or severity at baseline or over 12 weeks (P > 0.05 for all). In contrast, there was a trend toward greater frequency of moderate-to-severe hot flashes with higher RSA at baseline (β = 0.43, P = 0.06), and a positive association between change in RSA and change in frequency of moderate-to-severe hot flashes over 12 weeks (β = 0.63, P = 0.04). Among perimenopausal and postmenopausal women with hot flashes, variations in hot flash frequency and severity were not explained by variations in resting sympathetic activation. Greater parasympathetic activation was associated with more frequent moderate-to-severe hot flashes, which may reflect increased sensitivity to perceiving hot flashes.

Pulsed photoacoustic detection of flash-induced oxygen evolution from intact leaves and its oscillations

PubMed Central

Canaani, Ora; Malkin, Shmuel; Mauzerall, David

1988-01-01

Photoacoustic signals from intact leaves, produced upon excitation with single-turnover flashes, were shown to be dependent on their position in the flash sequence. Compared to the signal obtained from the first flash, all the others were time-shifted and had increased amplitudes. The signal from the third flash had the largest deviation, whereas that from the second flash deviated only minimally. The amplitude difference of the signals relative to that from the first flash was measured at a convenient time point (5 ms) and showed oscillations of period 4, similar to the O2-evolution pattern from algae. These oscillations were strongly damped, tending to a steady state from about the seventh flash on. The extra photoacoustic signal (relative to the first flash) was shown to be inhibited by 3-(3,4-dichlorophenyl)-1,1-dimethylurea, heat treatment, or water infiltration. Its change with flash number, its saturation with increasing flash energy, and the above inhibition criteria indicate that it originates in pulsed O2 evolution. The sound wave produced by the first flash, however, arose by a photothermal mechanism only, as shown by its linear dependence on the flash intensity and insensitivity to the above treatments. The above flash pattern demonstrates that the photocycle of the S states (i.e., positive charge accumulation before two water molecules can be oxidized in a concerted way to produce molecular oxygen) occurs in intact leaves. It proves the applicability of the photoacoustic method for mechanistic studies of O2 evolution in leaves under physiological conditions. Water content of leaves is readily measured by this method. Images PMID:16593952

Understanding the complex relationships underlying hot flashes: a Bayesian network approach.

PubMed

Smith, Rebecca L; Gallicchio, Lisa M; Flaws, Jodi A

2018-02-01

The mechanism underlying hot flashes is not well-understood, primarily because of complex relationships between and among hot flashes and their risk factors. We explored those relationships using a Bayesian network approach based on a 2006 to 2015 cohort study of hot flashes among 776 female residents, 45 to 54 years old, in the Baltimore area. Bayesian networks were fit for each outcome (current hot flashes, hot flashes before the end of the study, hot flash severity, hot flash frequency, and age at first hot flashes) separately and together with a list of risk factors (estrogen, progesterone, testosterone, body mass index and obesity, race, income level, education level, smoking history, drinking history, and activity level). Each fitting was conducted separately on all women and only perimenopausal women, at enrollment and 4 years after enrollment. Hormone levels, almost always interrelated, were the most common variable linked to hot flashes; hormone levels were sometimes related to body mass index, but were not directly related to any other risk factors. Smoking was also frequently associated with increased likelihood of severe symptoms, but not through an antiestrogenic pathway. The age at first hot flashes was related only to race. All other factors were either not related to outcomes or were mediated entirely by race, hormone levels, or smoking. These models can serve as a guide for design of studies into the causal network underlying hot flashes.

Brine contamination to aquatic resources from oil and gas development in the Williston Basin, United States

USGS Publications Warehouse

Gleason, Robert A.; Contributions by Chesley-Preston, Tara L.; Coleman, James L.; Haines, Seth S.; Jenni, Karen E.; Nieman, Timothy L.; Peterman, Zell E.; van der Burg, Max Post; Preston, Todd M.; Smith, Bruce D.; Tangen, Brian A.; Thamke, Joanna N.; Gleason, Robert A.; Tangen, Brian A.

2014-01-01

The Williston Basin, which includes parts of Montana, North Dakota, and South Dakota in the United States and the provinces of Manitoba and Saskatchewan in Canada, has been a leading domestic oil and gas producing region for more than one-half a century. Currently, there are renewed efforts to develop oil and gas resources from deep geologic formations, spurred by advances in recovery technologies and economic incentives associated with the price of oil. Domestic oil and gas production has many economic benefits and provides a means for the United States to fulfill a part of domestic energy demands; however, environmental hazards can be associated with this type of energy production in the Williston Basin, particularly to aquatic resources (surface water and shallow groundwater) by extremely saline water, or brine, which is produced with oil and gas. The primary source of concern is the migration of brine from buried reserve pits that were used to store produced water during recovery operations; however, there also are considerable risks of brine release from pipeline failures, poor infrastructure construction, and flow-back water from hydraulic fracturing associated with modern oilfield operations. During 2008, a multidisciplinary (biology, geology, water) team of U.S. Geological Survey researchers was assembled to investigate potential energy production effects in the Williston Basin. Researchers from the U.S. Geological Survey participated in field tours and met with representatives from county, State, tribal, and Federal agencies to identify information needs and focus research objectives. Common questions from agency personnel, especially those from the U.S. Fish and Wildlife Service, were “are the brine plumes (plumes of brine-contaminated groundwater) from abandoned oil wells affecting wetlands on Waterfowl Production Areas and National Wildlife Refuges?” and “are newer wells related to Bakken and Three Forks development different than the older, abandoned wells (in terms of potential for affecting aquatic resources)?” Of special concern were the wetland habitats of the ecologically important Prairie Pothole Region, which overlays a part of the Williston Basin and is recognized for the production of a majority of North America’s migratory waterfowl. On the basis of the concerns raised by on-the-ground land managers, as well as findings from previous research, a comprehensive study was developed with the following goals: summarize existing information pertaining to oil and gas production and aquatic resources in the Williston Basin; assess brine plume migration from new and previously studied sites in the Prairie Pothole Region; perform a regional, spatial evaluation of oil and gas production activities and aquatic resources; assess the potential for brine contamination to wetlands and streams; and hold a decision analysis workshop with key stakeholders to discuss issues pertaining to oil and gas production and environmental effects and to identify information gaps and research needs. This report represents an initial, multidisciplinary evaluation of measured and potential environmental effects associated with oil and gas production in the Williston Basin and Prairie Pothole Region. Throughout this report there are reviews of current knowledge, and discussions relating to data gaps and research needs. On the basis of the information presented, future research needs include: regional geophysical and water-quality assessments to establish baselines for current conditions and estimate the extent of previous brine contamination, investigations into the direct effects of brine to biotic communities, and evaluations to identify the most effective techniques to mitigate brine contamination.

Anoxic Corrosion of Steel and Lead in Na - Cl ± Mg-Dominated Brines in Atmospheres Containing CO2

NASA Astrophysics Data System (ADS)

Roselle, G. T.; Johnsen, S.; Allen, C.; Roselle, R.

2009-12-01

The Waste Isolation Pilot Plant (WIPP) is a deep geologic repository developed by the U.S. Department of Energy for the disposal of transuranic radioactive waste in bedded salt (Permian Salado Fm.). In order to minimize radionuclide release from the repository it is desirable to maintain these species in their least-soluble form (i.e., low oxidation states). Post-closure conditions in the WIPP will control the speciation and solubility of radionuclides in the waste. Microbially-produced CO2 from cellulosic, plastic and rubber materials in the waste may acidify any brine present and increase the actinide solubilities. Thus, the DOE emplaces MgO in the repository to buffer fCO2 and pH within ranges favoring lower actinide solubilities. Large quantities of low-C steel and Pb present in the WIPP may also consume CO2. We present initial results from a series of multiyear experiments investigating the corrosion of steel and Pb alloys under WIPP-relevant conditions. The objective is to determine the extent to which these alloys consume CO2 via the formation of carbonates or other phases, potentially supporting MgO in CO2 sequestration. In these experiments steel and Pb coupons are immersed in brines under WIPP-relevant conditions using a continuous gas flow-through system. The experimental apparatus maintains the following conditions: pO2 < 5 ppm; temperature of 26 °C; relative humidity at 78%±10%; and a range of pCO2 values (0, 350, 1500 and 3500 ppm, balance N2). Four high-ionic-strength-brines are used: Generic Weep Brine (GWB), a Na-Mg-Cl dominated brine associated with the Salado Fm.; Energy Research and Development Administration WIPP Well 6 (ERDA-6), a predominately Na-Cl brine; GWB with organic ligands (EDTA, acetate, citrate, and oxalate); and ERDA-6 with the same organic ligands. Steel coupons removed after 6 months show formation of several phases dependent on the pCO2. SEM analysis with EDS shows the presence of a green Fe (±Mg)-chlori-hydroxide phase at pCO2 values <1500 ppm. At higher pCO2 the dominant corrosion product is a Fe-Mg-Ca hydroxicarbonate phase. Lead coupons show no corrosion products at lower pCO2 values but significant formation of a Pb-Ca hydroxicarbonate phase at pCO2 > 350 ppm. Multiple cleaning cycles were used to remove all corrosion products from the coupons, which were then weighed to determine corrosive mass loss. These data are used to calculate average corrosion rates for each experimental condition. The data show that steel corrosion rates are a strong function of pCO2 for all brine types. ERDA-6 brines appear to be more corrosive than GWB brines. Steel corrosion rates vary from 0.08 ± 0.07 µm/yr at 0 ppm CO2 to 1.20 ± 0.25 µm/yr at 3500 ppm CO2. Corrosion rates for Pb coupons show no consistent trend as a function of pCO2 or brine type. Lead corrosion rates range from 0.18 ± 0.22 to 0.95 ± 0.56 µm/yr. This research is funded by WIPP programs administered by the U.S. Department of Energy. Sandia is a multiprogram laboratory operated by Sandia Corporation, a Lockheed Martin Company, for the United States Department of Energy’s National Nuclear Security Administration under contract DE-AC04-94AL85000.

Experimental confirmation of liquid brines on Mars

NASA Astrophysics Data System (ADS)

Fischer, E.; Renno, N. O.; Martinez, G.

2015-12-01

The discovery of water ice and perchlorates in the shallow subsurface of Mars [1,2] is interesting because they could produce aqueous liquid solutions under Mars' present-day environmental conditions. We used the Michigan Mars Environmental Chamber [3] to simulate the pressure, temperature and relative humidity during the full diurnal cycle of sol 19 at the Phoenix landing site. Sol 19 was chosen because on this sol ice found in a shallow trench (Dodo-Goldilocks) at a depth of ~5 cm was removed with little effort [4], suggesting that it was a frozen brine (softer than freshwater ice), and because oblate spheroids found on a strut of the lander, possibly a saline mud, were observed to grow and darken (suggesting liquefaction) [4]. The results of our simulations show that early in the mission the frozen brine likely found in the Dodo-Goldilocks trench could melt in the morning, temporarily forming aqueous liquid solutions when the temperature in the trench was above the eutectic temperature of the Ca(ClO4)2 salt (~199 K). In addition, the results of our simulations indicate that the spheroids observed on a strut of the Phoenix lander were most likely droplets of liquid brines. Since halophilic terrestrial bacteria thrive in brines [5], our results suggest that Mars' polar region could potentially be a habitat for microorganisms. In addition, it has been suggested that frost could form on fine-grained terrains at Gale crater during the winter [6]. If this frost gets in contact with perchlorate salts, it could melt temporarily forming liquid brines.

Chemical composition and distribution of lithium-rich brines in salar de Uyuni and nearby salars in southwestern Bolivia

USGS Publications Warehouse

Ericksen, G.E.; Vine, J.D.; Raul, Ballon A.

1978-01-01

Preliminary investigations at Salar de Uyuni and the nearby salars (salt pans) of Coipasa and Empexa in the southern part of the Bolivian Altiplano show the presence of widespread lithium-rich brines. Widely scattered brine samples from Salar de Uyuni, which has an area of about 9000 km2 and is the largest salt pan on earth, show lithium values ranging from 80 to 1500 ppm. High values of 300-700 ppm are most prevalent in an area of about 2500 km2 in the east-central and southeastern part of the salar. A few brine samples in small areas in Coipasa and Empexa Salars have values ranging from 170 to 580 ppm Li. All the brines are essentially saturated with halite and are moderately high in sulfate (5000-15,000 ppm SO4) but low in carbonate (<500 ppm HCO3). Potassium and magnesium values are relatively high, chiefly in the range of 2000-20,000 ppm, and the K Mg ratio is about 1:1. The Li K and Li Mg ratios are relatively constant at about 1:20. The crystalline saline material and brines in these salars are residual from a former large lake, Lago Minchin, that occupied much of the southern Bolivian Altiplano during late Pleistocene time, augmented by saline material carried to the salars by streams since final drying of this lake. Thermal springs associated with rhyolitic volcanic rocks of Quaternary age may have been a major source of the lithium. ?? 1978.

Advanced oxidation of iodinated X-ray contrast media in reverse osmosis brines: the influence of quenching.

PubMed

Azerrad, Sara P; Gur-Reznik, Shirra; Heller-Grossman, Lilly; Dosoretz, Carlos G

2014-10-01

Among the main restrictions for the implementation of advanced oxidation processes (AOPs) for removal of micropollutants present in reverse osmosis (RO) brines of secondary effluents account the quenching performed by background organic and inorganic constituents. Natural organic matter (NOM) and soluble microbial products (SMP) are the main effluent organic matter constituents. The inorganic fraction is largely constituted by chlorides and bicarbonate alkalinity with sodium and calcium as main counterions. The quenching influence of these components, separately and their mixture, in the transformation of model compounds by UVA/TiO2 was studied applying synthetic brines solutions mimicking 2-fold concentrated RO secondary effluents brines. The results were validated using fresh RO brines. Diatrizoate (DTZ) and iopromide (IOPr) were used as model compound. They have been found to exhibit relative high resistance to oxidation process and therefore represent good markers for AOPs techniques. Under the conditions applied, oxidization of DTZ in the background of RO brines was strongly affected by quenching effects. The major contribution to quenching resulted from organic matter (≈70%) followed by bicarbonate alkalinity (≈30%). NOM displayed higher quenching than SMP in spite of its relative lower concentration. Multivalent cations, i.e., Ca(+2), were found to decrease effectiveness of the technique due to agglomeration of the catalyst. However this influence was lowered in presence of NOM. Different patterns of transformation were found for each model compound in which a delayed deiodination was observed for iopromide whereas diatrizoate oxidation paralleled deiodination. Copyright © 2014 Elsevier Ltd. All rights reserved.

Origin of salt giants in abyssal serpentinite systems

NASA Astrophysics Data System (ADS)

Scribano, Vittorio; Carbone, Serafina; Manuella, Fabio C.; Hovland, Martin; Rueslåtten, Håkon; Johnsen, Hans-K.

2017-10-01

Worldwide marine salt deposits ranging over the entire geological record are generally considered climate-related evaporites, derived from the precipitation of salts (mainly chlorides and sulfates) from saturated solutions driven by solar evaporation of seawater. This explanation may be realistic for a salt thickness ≤100 m, being therefore inadequate for thicker (>1 km) deposits. Moreover, sub-seafloor salt deposits in deep marine basins are difficult to reconcile with a surface evaporation model. Marine geology reports on abyssal serpentinite systems provide an alternative explanation for some salt deposits. Seawater-driven serpentinization consumes water and increases the salinity of the associated aqueous brines. Brines can be trapped in fractures and cavities in serpentinites and the surrounding `country' rocks. Successive thermal dehydration of buried serpentinites can mobilize and accumulate the brines, forming highly saline hydrothermal solutions. These can migrate upwards and erupt onto the seafloor as saline geysers, which may form salt-saturated water pools, as are currently observed in numerous deeps in the Red Sea and elsewhere. The drainage of deep-seated saline brines to seafloor may be a long-lasting, effective process, mainly occurring in areas characterized by strong tectonic stresses and/or igneous intrusions. Alternatively, brines could be slowly expelled from fractured serpentinites by buoyancy gradients and, hence, separated salts/brines could intrude vertically into surrounding rocks, forming salt diapirs. Serpentinization is an ubiquitous, exothermic, long-lasting process which can modify large volumes of oceanic lithosphere over geological times. Therefore, buried salt deposits in many areas of the world can be reasonably related to serpentinites.

Advances in Spacecraft Brine Water Recovery: Development of a Radial Vaned Capillary Drying Tray

NASA Technical Reports Server (NTRS)

Callahan, Michael R.; Sargusingh, Miriam J.; Pickering, Karen D.; Weislogel, Mark M.

2014-01-01

Technology improvements in the recovery of water from brine are critical to establishing closed-loop water recovery systems, enabling long-duration missions, and achieving a sustained human presence in space. A genre of 'in-place drying' brine water recovery concepts, collectively referred to herein as Brine Residual In-Containment, are under development. These brine water recovery concepts aim to increase the overall robustness and reliability of the brine recovery process by performing drying inside the container used for final disposal of the solid residual waste. Implementation of in-place drying techniques have been demonstrated for applications where gravity is present and phase separation occurs naturally by buoyancy-induced effects. In this work, a microgravity-compatible analogue of the gravity-driven phase separation process is considered by exploiting capillarity in the form of surface wetting, surface tension, and container geometry. The proposed design consists of a series of planar radial vanes aligned about a central slotted core. Preliminary testing of the fundamental geometry in a reduced gravity environment has shown the device to spontaneously fill and saturate rapidly, thereby creating a free surface from which evaporation and phase separation can occur similar to a terrestrial-like 'cylindrical pool' of fluid. Mathematical modeling and analysis of the design suggest predictable rates of filling and stability of fluid containment as a function of relevant system dimensions; e.g., number of vanes, vane length, width, and thickness. A description of the proposed capillary design solution is presented along with preliminary results from testing, modeling, and analysis of the system.

Analytical model for screening potential CO2 repositories

USGS Publications Warehouse

Okwen, R.T.; Stewart, M.T.; Cunningham, J.A.

2011-01-01

Assessing potential repositories for geologic sequestration of carbon dioxide using numerical models can be complicated, costly, and time-consuming, especially when faced with the challenge of selecting a repository from a multitude of potential repositories. This paper presents a set of simple analytical equations (model), based on the work of previous researchers, that could be used to evaluate the suitability of candidate repositories for subsurface sequestration of carbon dioxide. We considered the injection of carbon dioxide at a constant rate into a confined saline aquifer via a fully perforated vertical injection well. The validity of the analytical model was assessed via comparison with the TOUGH2 numerical model. The metrics used in comparing the two models include (1) spatial variations in formation pressure and (2) vertically integrated brine saturation profile. The analytical model and TOUGH2 show excellent agreement in their results when similar input conditions and assumptions are applied in both. The analytical model neglects capillary pressure and the pressure dependence of fluid properties. However, simulations in TOUGH2 indicate that little error is introduced by these simplifications. Sensitivity studies indicate that the agreement between the analytical model and TOUGH2 depends strongly on (1) the residual brine saturation, (2) the difference in density between carbon dioxide and resident brine (buoyancy), and (3) the relationship between relative permeability and brine saturation. The results achieved suggest that the analytical model is valid when the relationship between relative permeability and brine saturation is linear or quasi-linear and when the irreducible saturation of brine is zero or very small. ?? 2011 Springer Science+Business Media B.V.

An X-ray spectroscopic perspective on Messinian evaporite from Sicily: Sedimentary fabrics, element distributions, and chemical environments of S and Mg

NASA Astrophysics Data System (ADS)

Yoshimura, Toshihiro; Kuroda, Junichiro; Lugli, Stefano; Tamenori, Yusuke; Ogawa, Nanako O.; Jiménez-Espejo, Francisco J.; Isaji, Yuta; Roveri, Marco; Manzi, Vinicio; Kawahata, Hodaka; Ohkouchi, Naohiko

2016-04-01

The Messinian salinity crisis is a dramatic hydrological and biological crisis that occurred in the Mediterranean basin at 5.97-5.33 Ma. The interpretation of the facies and stratigraphic associations of the Messinian salt deposits is still the object of active research because of the absence of modern depositional analogues of comparable scale. In this study, the spatial distributions of Na, Mg, S, O, Si, and Al in a potassic-magnesian salt and a halite layers of Messinian evaporites from the Realmonte mine on Sicily were determined using synchrotron based micro-X-ray fluorescence. The dominant molecular host site of Mg and S obtained by X-ray absorption near edge structure (XANES) is applied to specify the hydrochemistry of hypersaline brines and the presence of diagenetic minerals, thus shedding light on evaporative concentration processes in the Caltanissetta Basin of Sicily. Mg and S K-edge XANES spectra revealed the presence of highly soluble Mg-bearing sulfates. The massive halite layer "unit C," contains less soluble minerals, thus did not exceed the stage of halite crystallization. We infer that as evaporative concentration increased, the density of the brine at the shallow margin of the basin increased as salinity increased to concentrations over 70 times the starting values, creating brines that were oversaturated with Mg-sulfate. Density stratification of the deep basin caused heavy brines to sink to the bottom and become overlain by more dilute brines. We propose lateral advection of dense Mg-sulfate brines that certainly affected marine biota.

Recharge and Groundwater Flow Within an Intracratonic Basin, Midwestern United States.

PubMed

Panno, Samuel V; Askari, Zohreh; Kelly, Walton R; Parris, Thomas M; Hackley, Keith C

2018-01-01

The conservative nature of chloride (Cl - ) in groundwater and the abundance of geochemical data from various sources (both published and unpublished) provided a means of developing, for the first time, a representation of the hydrogeology of the Illinois Basin on a basin-wide scale. The creation of Cl - isocons superimposed on plan view maps of selected formations and on cross sections across the Illinois Basin yielded a conceptual model on a basin-wide scale of recharge into, groundwater flow within and through the Illinois Basin. The maps and cross sections reveal the infiltration and movement of freshwater into the basin and dilution of brines within various geologic strata occurring at basin margins and along geologic structures. Cross-formational movement of brines is also seen in the northern part of the basin. The maps and cross sections also show barriers to groundwater movement created by aquitards resulting in areas of apparent isolation/stagnation of concentrated brines within the basin. The distribution of Cl - within the Illinois Basin suggests that the current chemical composition of groundwater and distribution of brines within the basin is dependent on five parameters: (1) presence of bedrock exposures along basin margins; (2) permeability of geologic strata and their distribution relative to one another; (3) presence or absence of major geologic structures; (4) intersection of major waterways with geologic structures, basin margins, and permeable bedrock exposures; and (5) isolation of brines within the basin due to aquitards, inhomogeneous permeability, and, in the case of the deepest part of the basin, brine density effects. © 2017, National Ground Water Association.

Hot Flashes

MedlinePlus

... report menopausal hot flashes than do women of European descent. Hot flashes are less common in women of Japanese and Chinese descent than in white European women. Complications Nighttime hot flashes (night sweats) can ...

Helium shell flashes and evolution of accreting white dwarfs

NASA Astrophysics Data System (ADS)

Fujimoto, M. Y.; Sugimoto, D.

1982-06-01

The evolution of accreting white dwarfs is investigated from the onset of accretion through the helium shell flash. Properties of the helium shell flashes are studied by means of a generalized theory of shell flash and by numerical computations, and it is found that the shell flash grows up to the strength of a supernova explosion when the mass of the helium zone is large enough on a massive white dwarf. Although accretion onto a hot white dwarf causes a weaker shell flash than those onto cool ones, a strong tendency exists for the strength to be determined mainly by the accretion rate. For fast accretion, the shell flashes are weak and triggered recurrently, while for slow accretion the helium shell flash, once triggered, develops into a detonation supernova.

Circulating interleukin-8 and tumor necrosis factor-α are associated with hot flashes in healthy postmenopausal women.

PubMed

Huang, Wan-Yu; Hsin, I-Lun; Chen, Dar-Ren; Chang, Chia-Chu; Kor, Chew-Teng; Chen, Ting-Yu; Wu, Hung-Ming

2017-01-01

Hot flashes have been postulated to be linked to systemic inflammation. This study aimed to investigate the relationship between hot flashes, pro-inflammatory factors, and leukocytes in healthy, non-obese postmenopausal women. In this cross-sectional study, a total of 202 women aged 45-60 years were stratified into one of four groups according to their hot-flash status: never experienced hot flashes (Group N), mild hot flashes (Group m), moderate hot flashes (Group M), and severe hot flashes (Group S). Variables measured in this study included clinical parameters, hot flash experience, leukocytes, and fasting plasma levels of nine circulating cytokines/chemokines measured by using multiplex assays. Multiple linear regression analysis was used to evaluate the associations of hot flashes with these pro-inflammatory factors. The study was performed in a hospital medical center. The mean values of leukocyte number were not different between these four groups. The hot flash status had a positive tendency toward increased levels of circulating IL-6 (P-trend = 0.049), IL-8 (P-trend < 0.001), TNF-α (P-trend = 0.008), and MIP1β (P-trend = 0.04). Multivariate linear regression analysis revealed that hot-flash severity was significantly associated with IL-8 (P-trend < 0.001) and TNFα (P-trend = 0.007) among these nine cytokines/chemokines after adjustment for age, menopausal duration, BMI and FSH. Multivariate analysis further revealed that severe hot flashes were strongly associated with a higher IL-8 (% difference, 37.19%; 95% confidence interval, 14.98,63.69; P < 0.001) and TNFα (51.27%; 6.64,114.57; P < 0.05). The present study provides evidence that hot flashes are associated with circulating IL-8 and TNF-α in healthy postmenopausal women. It suggests that hot flashes might be related to low-grade systemic inflammation.

Expectancy after the first treatment and response to acupuncture for menopausal hot flashes.

PubMed

Ee, Carolyn C; Thuraisingam, Sharmala; Pirotta, Marie V; French, Simon D; Xue, Charlie C; Teede, Helena J

2017-01-01

Evidence on the impact of expectancy on acupuncture treatment response is conflicting. This secondary analysis of a randomized sham-controlled trial on acupuncture for menopausal hot flashes investigated whether treatment expectancy score was associated with hot flash score at end-of-treatment. Secondary analyses investigated whether there were associations between other pre-specified factors and hot flash score. Women experiencing moderately-severe hot flashes were randomized to receive 10 sessions of real or sham acupuncture over eight weeks. Hot flash score was collected using a seven-day hot flash diary, and expectancy using the modified Credibility and Expectancy Questionnaire immediately after the first treatment. Linear mixed-effects models with random intercepts were used to identify associations between expectancy score and hot flash score at end-of-treatment. Regression was also used to identify associations between pre-specified factors of interest and hot flash score. Because there was no difference between real and sham acupuncture for the primary outcome of hot flash score, both arms were combined in the analysis. 285 women returned the Credibility and Expectancy Questionnaire, and 283 women completed both expectancy measures. We found no evidence for an association between expectancy and hot flash score at end-of-treatment for individual cases in either acupuncture or sham group. Hot flash scores at end-of-treatment were 8.1 (95%CI, 3.0 to 13.2; P = 0.002) points lower in regular smokers compared to those who had never smoked, equivalent to four fewer moderate hot flashes a day. In our study of acupuncture for menopausal hot flashes, higher expectancy after the first treatment did not predict better treatment outcomes. Future research may focus on other determinants of outcomes in acupuncture such as therapist attention. The relationship between smoking and hot flashes is poorly understood and needs further exploration.

Circulating interleukin-8 and tumor necrosis factor-α are associated with hot flashes in healthy postmenopausal women

PubMed Central

Huang, Wan-Yu; Hsin, I-Lun; Chen, Dar-Ren; Chang, Chia-Chu; Kor, Chew-Teng; Chen, Ting-Yu

2017-01-01

Introduction Hot flashes have been postulated to be linked to systemic inflammation. This study aimed to investigate the relationship between hot flashes, pro-inflammatory factors, and leukocytes in healthy, non-obese postmenopausal women. Participants and design In this cross-sectional study, a total of 202 women aged 45–60 years were stratified into one of four groups according to their hot-flash status: never experienced hot flashes (Group N), mild hot flashes (Group m), moderate hot flashes (Group M), and severe hot flashes (Group S). Variables measured in this study included clinical parameters, hot flash experience, leukocytes, and fasting plasma levels of nine circulating cytokines/chemokines measured by using multiplex assays. Multiple linear regression analysis was used to evaluate the associations of hot flashes with these pro-inflammatory factors. Settings The study was performed in a hospital medical center. Results The mean values of leukocyte number were not different between these four groups. The hot flash status had a positive tendency toward increased levels of circulating IL-6 (P-trend = 0.049), IL-8 (P-trend < 0.001), TNF-α (P-trend = 0.008), and MIP1β (P-trend = 0.04). Multivariate linear regression analysis revealed that hot-flash severity was significantly associated with IL-8 (P-trend < 0.001) and TNFα (P-trend = 0.007) among these nine cytokines/chemokines after adjustment for age, menopausal duration, BMI and FSH. Multivariate analysis further revealed that severe hot flashes were strongly associated with a higher IL-8 (% difference, 37.19%; 95% confidence interval, 14.98,63.69; P < 0.001) and TNFα (51.27%; 6.64,114.57; P < 0.05). Conclusion The present study provides evidence that hot flashes are associated with circulating IL-8 and TNF-α in healthy postmenopausal women. It suggests that hot flashes might be related to low-grade systemic inflammation. PMID:28846735

A first look at global flash drought: long term change and short term predictability

NASA Astrophysics Data System (ADS)

Yuan, Xing; Wang, Linying; Ji, Peng

2017-04-01

"Flash drought" became popular after the unexpected 2012 central USA drought, mainly due to its rapid development, low predictability and devastating impacts on water resources and crop yields. A pilot study by Mo and Lettenmaier (2015) found that flash drought, based on a definition of concurrent heat extreme, soil moisture deficit and evapotranspiration (ET) enhancement at pentad scale, were in decline over USA during recent 100 years. Meanwhile, a recent work indicated that the occurrence of flash drought in China was doubled during the past 30 years, where a severe flash drought in the summer of 2013 ravaged 13 provinces in southern China. As global warming increases the frequency of heat waves and accelerates the hydrological cycle, the flash drought is expected to increase in general, but its trend might also be affected by interannual to decadal climate oscillations. To consolidate the hotspots of flash drought and the effects of climate change on flash drought, a global inventory is being conducted by using multi-source observations (in-situ, satellite and reanalysis), CMIP5 historical simulations and future projections under different forcing scenarios, as well as global land surface hydrological modeling for key variables including surface air temperature, soil moisture and ET. In particular, a global picture of the flash drought distribution, the contribution of naturalized and anthropogenic forcings to global flash drought change, and the risk of global flash drought in the future, will be presented. Besides investigating the long-term change of flash drought, providing reliable early warning is also essential to developing adaptation strategies. While regional drought early warning systems have been emerging in recent decade, forecasting of flash drought is still at an exploratory stage due to limited understanding of flash drought predictability. Here, a set of sub-seasonal to seasonal (S2S) hindcast datasets are being used to assess the short term predictability of flash drought via a perfect model assumption.

Use of a Brine Shrimp Assay to Study Herbal Teas in the Classroom.

ERIC Educational Resources Information Center

Opler, Annette; Mizell, Rebecca; Robert, Alexander; Cervantes-Cervantes, Miguel; Kincaid, Dwight; Kennelly, Edward J.

2002-01-01

Introduces a brine shrimp assay to demonstrate the effects of the biological activity of herbal remedies. Describes two protocols, one using aqueous extracts and the other using methanol extracts. (Contains 21 references.) (YDS)

Geothermal Thermoelectric Generation (G-TEG) with Integrated Temperature Driven Membrane Distillation and Novel Manganese Oxide for Lithium Extraction

DOE Office of Scientific and Technical Information (OSTI.GOV)

Renew, Jay; Hansen, Tim

Southern Research Institute (Southern) teamed with partners Novus Energy Technologies (Novus), Carus Corporation (Carus), and Applied Membrane Technology, Inc. (AMT) to develop an innovative Geothermal ThermoElectric Generation (G-TEG) system specially designed to both generate electricity and extract high-value lithium (Li) from low-temperature geothermal brines. The process combined five modular technologies including – silica removal, nanofiltration (NF), membrane distillation (MD), Mn-oxide sorbent for Li recovery, and TEG. This project provides a proof of concept for each of these technologies. The first step in the process is silica precipitation through metal addition and pH adjustment to prevent downstream scaling in membrane processes.more » Next, the geothermal brine is concentrated with the first of a two stage MD system. The first stage MD system is made of a high-temperature material to withstand geothermal brine temperatures up to 150C.° The first stage MD is integrated with a G-TEG module for simultaneous energy generation. The release of energy from the MD permeate drives heat transfer across the TE module, producing electricity. The first stage MD concentrate is then treated utilizing an NF system to remove Ca 2+ and Mg 2+. The NF concentrate will be disposed in the well by reinjection. The NF permeate undergoes concentration in a second stage of MD (polymeric material) to further concentrate Li in the NF permeate and enhance the efficiency of the downstream Li recovery process utilizing a Mn-oxide sorbent. Permeate from both the stages of the MD can be beneficially utilized as the permeates will contain less contaminants than the feed water. The concentrated geothermal brines are then contacted with the Mn-oxide sorbent. After Li from the geothermal brine is adsorbed on the sorbent, HCl is then utilized to regenerate the sorbent and recover the Li. The research and development project showed that the Si removal goal (>80%) could be achieved by increasing the pH of the brine and adding Fe 3+ under several scenarios. The NF was also successful in achieving significant Ca 2+ and Mg 2+ removal (~80%) while retaining most Li in the permeate for high strength brines. MD experiments showed that geothermal brines could be significantly concentrated with little fouling due to pre-treatment.« less

Ultra-high chlorine in submarine Kı̄lauea glasses: Evidence for direct assimilation of brine by magma

USGS Publications Warehouse

Coombs, Michelle L.; Sisson, Thomas W.; Kimura, Jun-Ichi

2004-01-01

Basaltic glass grains from the submarine south flank of Kı̄lauea, Hawai′i, have Cl concentrations of 0.01–1.68 wt%, the latter being the highest Cl content yet recorded for a Hawaiian glass. The high-Cl glass grains are products of brine assimilation by tholeiite magma. The glasses are grains in a sandstone clast from bedded breccias draping the southwestern margin of Kı̄lauea’s submarine midslope bench. The clast contains two distinct suites of glass grains: abundant degassed tholeiites, perhaps derived from subaerial lavas of Mauna Loa that shattered upon ocean entry, and a smaller population of Kea-type tholeiite (n=17 analyzed) that erupted subaqueously, based on elevated S (780–1050 ppm), H2O (0.42–1.27 wt%), and CO2 (<30–120 ppm), probably early in Kı̄lauea’s shield-building stage. Ten grains in this group have Cl>1000 ppm, six >5000 ppm, and two grains have >10 000 ppm dissolved Cl. Abundances of H2O, Na2O, K2O, and several trace elements increase regularly with Cl concentration, and we estimate that Cl enrichment was due to up to 13 wt% addition of a brine consisting of 78% H2O (wt), 13% Cl, 4.4% Na, 2.6% K, 2.6% Ca, 620 ppm Ba, 360 ppm Sr, 65 ppm Rb, and 7 ppm Pb. The large amounts of brine addition argue against bulk assimilation of low-porosity brine-bearing rock. The brine’s composition is appropriate for a seawater-derived hydrothermal fluid that reacted with basaltic wall rocks at T>100°C, losing Mg and S and gaining K, Ca, Rb, Ba, Sr, and Pb, followed by phase separation near 500°C and ∼50 MPa (5 km below sea level at hydrostatic pressure). Brine was assimilated at or near the depth it formed, as estimated on petrologic grounds, but under lithostatic conditions. The highest extents of assimilation either forced volatile saturation of the magma or enriched already coexisting magmatic vapor in H2O. Possible mechanisms for assimilation are: (1) forcible injection of brine into magma during bursting of overpressured pockets heated by new dikes, or (2) intrusion of magma into lenses or sills occupied by trapped brine.

Fate and identification of oil-brine contamination in different hydrogeologic settings

USGS Publications Warehouse

Whittemore, Donald O.

2007-01-01

Past disposal of oil-field brine at the surface has caused substantial contamination of water resources in Kansas. Natural saline water occurs in and discharges from Permian bedrock in parts of the state, and other anthropogenic sources of saline water exist, requiring clear identification of different sources. Time-series analysis of Cl- concentration and streamflow relative to pre-contamination contents, and end-member mixing plots, especially for Br- and Cl-, are practical methods for source differentiation and quantification. Although regulations preventing escape of saltwater from oil wells were first passed in Kansas in 1935, much oil and gas brine was disposed on the surface through the 1940s. Hydrogeologic characteristics of the areas with past surface disposal of oil brine differ appreciably and result in large differences in the ratio of saltwater transported in streams or ground water. Much of the brine disposed during the 1910s to 1940s in an area of silty clay soils overlying shale and limestone bedrock in south-central Kansas soon ran off or was flushed from the surface by rain into streams. Chloride concentration in the rivers draining this area often exceeded 1000 mg/L after the start of oil production up to the 1950s. Chloride content in the rivers then generally declined to about 100 mg/L or less in recent low flows. Oil brine was also disposed in surface ponds overlying the unconsolidated High Plains aquifer in south-central Kansas from the latter 1920s into the 1940s. Most of the surface-disposed brine infiltrated to the underlying aquifer. Where the High Plains aquifer is thin, saltwater has migrated along the top of clay layers or the underlying shaly bedrock and either discharged into small streams or flowed into thicker parts of the aquifer. Where the aquifer is thick, surface-disposed oil brine moved downward until reaching clay lenses, migrated latterly to the edge of the clay, and again moved downward if still dense enough. Water-level declines from pumping have increased the lateral migration rate of the saltwater contamination in the aquifer towards water-supply wells. The period of flushing most of the surface-disposed saltwater from the area of shale and limestone bedrock is on the order of many decades but is at least many centuries for the deeper parts of the High Plains aquifer. ?? 2007 Elsevier Ltd. All rights reserved.

Hydrogen-alkali exchange between silicate melts and two-phase aqueous mixtures: an experimental investigation

NASA Astrophysics Data System (ADS)

Williams, Thomas J.; Candela, Philip A.; Piccoli, Philip M.

Experiments were performed in the three-phase system high-silica rhyolite melt + low-salinity aqueous vapor + hydrosaline brine, to investigate the exchange equilibria for hydrogen, potassium, and sodium in magmatic-hydrothermal systems at 800 °C and 100 MPa, and 850 °C and 50 MPa. The Kaqm/meltH,Na and Kaqm/meltH,K for hydrogen-sodium exchange between a vapor + brine mixture and a silicate melt are inversely proportional to the total chloride concentration (ΣCl) in the vapor + brine mixture indicating that HCl/NaCl and HCl/KCl are higher in the low-salinity aqueous vapor relative to high-salinity brine. The equilibrium constants for vapor/melt and brine/melt exchange were extracted from regressions of Kaqm/meltH,Na and Kaqm/meltH,K versus the proportion of aqueous vapor relative to brine in the aqueous mixture (Faqv) at P and T, expressed as a function of ΣCl. No significant pressure effect on the empirically determined exchange constants was observed for the range of pressures investigated. Model equilibrium constants are: Kaqv/meltH,Na(vapor/melt)=26(+/-1.3) at 100 MPa (800 °C), and 19( +/- 7.0) at 50 MPa (850 °C) Kaqv/meltH,K=14(+/-1.1) at 100 MPa (800 °C), and 24(+/-12) at 50 MPa (850 °C) Kaqb/meltH,b(brine/melt)= 1.6(+/-0.7) at 100 MPa (800 °C), and 3.9(+/-2.3) at 50 MPa (850 °C) and Kaqb/meltH,K=2.7(+/-1.2) at 100 MPa (800 °C) and 3.8(+/-2.3) at 50 MPa (850 °C). Values for Kaqv/meltH,K and Kaqb/meltH,K were used to calculate KCl/HCl in the aqueous vapor and brine as a function of melt aluminum saturation index (ASI: molar Al2O3/(K2O+Na2O+CaO) and pressure. The model log KCl/HCl values show that a change in melt ASI from peraluminous (ASI = 1.04) to moderately metaluminous (ASI = 1.01) shifts the cooling pathway (in temperature-log KCl/HCl space) of the aqueous vapor toward the andalusite+muscovite+K-feldspar reaction point.

Scale Resistant Heat Exchanger for Low Temperature Geothermal Binary Cycle Power Plant

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hays, Lance G.

2014-11-18

Phase 1 of the investigation of improvements to low temperature geothermal power systems was completed. The improvements considered were reduction of scaling in heat exchangers and a hermetic turbine generator (eliminating seals, seal system, gearbox, and lube oil system). A scaling test system with several experiments was designed and operated at Coso geothermal resource with brine having a high scaling potential. Several methods were investigated at the brine temperature of 235 ºF. One method, circulation of abradable balls through the brine passages, was found to substantially reduce scale deposits. The test heat exchanger was operated with brine outlet temperatures asmore » low as 125 ºF, which enables increased heat input available to power conversion systems. For advanced low temperature cycles, such as the Variable Phase Cycle (VPC) or Kalina Cycle, the lower brine temperature will result in a 20-30% increase in power production from low temperature resources. A preliminary design of an abradable ball system (ABS) was done for the heat exchanger of the 1 megawatt VPC system at Coso resource. The ABS will be installed and demonstrated in Phase 2 of this project, increasing the power production above that possible with the present 175 ºF brine outlet limit. A hermetic turbine generator (TGH) was designed and manufacturing drawings produced. This unit will use the working fluid (R134a) to lubricate the bearings and cool the generator. The 200 kW turbine directly drives the generator, eliminating a gearbox and lube oil system. Elimination of external seals eliminates the potential of leakage of the refrigerant or hydrocarbon working fluids, resulting in environmental improvement. A similar design has been demonstrated by Energent in an ORC waste heat recovery system. The existing VPC power plant at Coso was modified to enable the “piggyback” demonstration of the TGH. The existing heat exchanger, pumps, and condenser will be operated to provide the required process conditions for the TGH demonstration. Operation of the TGH with and without the ABS system will demonstrate an increase in geothermal resource productivity for the VPC from 1 MW/(million lb) of brine to 1.75 MW/(million lb) of brine, a 75% increase.« less

Rainy Periods and Bottom Water Stagnation Initiating Brine Accumulation and Metal Concentrations: 1. The Late Quaternary

NASA Astrophysics Data System (ADS)

Rossignol-Strick, Martine

1987-06-01

A working hypothesis is proposed to account for the present accumulation of brines in isolated pockets of the ocean floor and for the formation of the underlying organic and metal-rich sediments. These are the Tyro and Bannock basins in the East Mediterranean, the Red Sea Deeps, and the Orca Basin in the northern Gulf of Mexico. Initiation of brine-derived deposition in the Red Sea Deeps and Orca Basin occurred between 12,000 and 8000 years B.P. This time bracket also encompasses the formation of the latest East Mediterranean sapropel and the wettest global climate since the last glacial maximum. This wet period first appeared in the tropics around 12,000 years B.P, then in the subtropical and middle latitudes. During the same period, the 23,000 year precession cycle brought the summer insolation of the northern hemisphere to its peak at 11,000 years B.P. with retreating northern hemisphere ice sheets. The Red Sea Deeps and the Orca Basin became anoxic during this humid period, and metal-rich sapropel deposition then began. In contrast, the Tyro and Bannock basins began accumulating a brine long before and persisted beyond this climatic stage. The hypothesis involves two propositions: (1) As in the Eastern Mediterranean Sea, marine anoxia was mainly the consequence of the large influx of continental runoff and local precipitation. Longer residence time of bottom waters, so-called "stagnation," in silled rimmed basins would have resulted from lower salinity at the sea surface in areas of deep water formation in the Eastern Mediterranean, the Red Sea, and the Gulf of Mexico and (2) Miocene or older evaporites underlie these basins or outcrop on their flanks. Leaching from these evaporites was an ongoing process before the quasi-stagnation phase, but the initial leachate, much less saline than the present brines, was continuously flushed by bottom circulation. The climate-induced quiescence of bottom waters in these basins enabled the leachate to accumulate. The feedback of stagnation by increased density progressively raised the salinity of entrapped bottom waters to the present brine concentration. The high density has resisted brine removal by bottom circulation until present time, long after cessation of the initiating wet period. The brines therefore are stagnant, fossil waters.

Muzzle flash issues related to the Waco FLIR analysis

NASA Astrophysics Data System (ADS)

Grant, Barbara G.; Hardy, David T.

2001-09-01

The controversy surrounding the origin of flashes on the Mt. Carmel FLIR videotape acquired on April 19, 1993, is introduced. The characteristics of muzzle flash are reviewed. A comparative weapons description is offered. The temporal, spatial, and radiance characteristics of thermal infrared muzzle flash are addressed. Data acquired from a field experiment are presented. The authors conclude that the spatial characteristics of muzzle flash enable its detection by equipment such as the FLIR in use at Mt. Carmel on April 19, 1993; that while flashes obtained in the field appear highly radiant, measurements are necessary to quantify their values; and that the temporal behavior of muzzle flash deserves further study.

Initial Breakdown Pulse Parameters in Intracloud and Cloud-to-Ground Lightning Flashes

NASA Astrophysics Data System (ADS)

Smith, E. M.; Marshall, T. C.; Karunarathne, S.; Siedlecki, R.; Stolzenburg, M.

2018-02-01

This study analyzes the largest initial breakdown (IB) pulse in flashes from four storms in Florida; data from three sensor arrays are used. The range-normalized, zero-to-peak amplitude of the largest IB pulse was determined along with its altitude, duration, and timing within each flash. Appropriate data were available for 40 intracloud (IC) and 32 cloud-to-ground (CG) flashes. Histograms of amplitude of the largest IB pulse by flash type were similar, with mean (median) values of 1.49 (1.05) V/m for IC flashes and -1.35 (-0.87) V/m for CG flashes. The largest IB pulse in 30 IC flashes showed a weak inverse relation between pulse amplitude and altitude. Amplitude of the largest IB pulse for 25 CG flashes showed no altitude correlation. Duration of the largest IB pulse in ICs averaged twice as long as in CGs (96 μs versus 46 μs), and all of the CG durations were <100 μs. Among the ICs, there is a positive relation between largest IB pulse duration and amplitude; the linear correlation coefficient is 0.385 with outliers excluded. The largest IB pulse in IC flashes typically occurred at a longer time after the first IB pulse (average 4.1 ms) than was the case in CG flashes (average 0.6 ms). In both flash types, the largest IB pulse was the first IB pulse in about 30% of the cases. In one storm all 42 IC flashes with triggered data had IB pulses.

Experimental check of bremsstrahlung dosimetry predictions for 0.75 MeV electrons

NASA Astrophysics Data System (ADS)

Sanford, T. W. L.; Halbleib, J. A.; Beezhold, W.

Bremsstrahlung dose in CaF2 TLDs from the radiation produced by 0.75 MeV electrons incident on Ta/C targets is measured and compared with that calculated via the CYLTRAN Monte Carlo code. The comparison was made to validate the code, which is used to predict and analyze radiation environments of flash X-ray simulators measured by TLDs. Over a wide range of Ta target thicknesses and radiation angles the code is found to agree with the 5% measurements. For Ta thickness near those that optimize the radiation output, however, the code overestimates the radiation dose at small angles. Maximum overprediction is about 14 + or - 5%. The general agreement, nonetheless, gives confidence in using the code at this energy and in the TLD calibration procedure. For the bulk of the measurements, a standard TLD employing a 2.2 mm thick Al equilibrator was used. In this paper we also show that this thickness can significantly attenuate the free-field dose and introduces significant photon buildup in the equalibrator.

High repetition rate compact source of nanosecond pulses of 5-100 keV x-ray photons

NASA Astrophysics Data System (ADS)

Khacef, A.; Viladrosa, R.; Cachoncinlle, C.; Robert, E.; Pouvesle, J. M.

1997-06-01

A powerful, compact, and repetitive flash x-ray system based on a cable transformer technology powered by ceramic capacitors in a Blumlein-like configuration has been developed. Open circuit voltages in excess of 100 kV can be achieved while commutation occurs at low voltage (<20 kV). The x-ray emission from a low impedance x-ray diode with a hollow cathode configuration was observed under a wide range of experimental conditions. The critical parameters limiting the flash x-ray performances are mainly the pressure in the x-ray diode and the anode-cathode space. This true table top device is able to produce doses up to 1 R per shot, measured at the output window, of x-rays between 5 and 100 keV. The pulse widths were about 20 ns and the maximum repetition rate was about 60 Hz. Operation is possible in air or in other gases (He, Ne, Ar, Kr, Xe, H2, N2) at pressures varying from 10-3 mbar for xenon to about 1 mbar for helium.

Cloud-to-ground lightning and surface rainfall in warm-season Florida thunderstorms

USGS Publications Warehouse

Gungle, B.; Krider, E.P.

2006-01-01

Relationships between cloud-to-ground (CG) lightning and surface rainfall have been examined in nine isolated, warm-season thunderstorms on the east coast of central Florida. CG flashes and the associated rain volumes were measured as a function of time in storm-centered reference frames that followed each storm over a network of rain gauges. Values of the storm-average rain volume per CG flash ranged from 0.70 ?? 104 to 6.4 ?? 104 m3/CG flash, with a mean (and standard deviation) of 2.6 ?? 104 ?? 2.1 ?? 104 m3/CG flash. Values of the rain volume concurrent with CG flashes ranged from 0.11 ?? 104 to 4.9 ?? 104 m3/CG flash with a mean of 2.1 ?? 104 ?? 2.0 ?? 104 m3/CG flash. The lag-time between the peak CG flash rate and the peak rainfall rate (using 5 min bins), and the results of a lag correlation analysis, show that surface rainfall tends to follow the lightning (positive lag) by up to 20 min in six storms. In one storm the rainfall preceded the lightning by 5 min, and two storms had nonsignificant lags. Values of the lagged rain volume concurrent with CG flashes ranged from 0.43 ?? 104 to 4.9 ?? 104 m3/CG flash, and the mean was 1.9 ?? 104 ?? 1.7 ?? 104 m3/CG flash. For the five storms that produced 12 or more flashes and had significant lags, a plot of the optimum lag time versus the total number of CG flashes shows a linear trend (R2 = 0.56). The number of storms is limited, but the lag results do indicate that large storms tend to have longer lags. A linear fit to the lagged rain volume vs. the number of concurrent CG flashes has a slope of 1.9 ?? 104 m3/CG flash (R2 = 0.83). We conclude that warm-season Florida thunderstorms produce a roughly constant rain volume per CG flash and that CG lightning can be used to estimate the location and intensity of convective rainfall in that weather regime. Copyright 2006 by the American Geophysical Union.

High-pitch computed tomography coronary angiography-a new dose-saving algorithm: estimation of radiation exposure.

PubMed

Ketelsen, Dominik; Buchgeister, Markus; Korn, Andreas; Fenchel, Michael; Schmidt, Bernhard; Flohr, Thomas G; Thomas, Christoph; Schabel, Christoph; Tsiflikas, Ilias; Syha, Roland; Claussen, Claus D; Heuschmid, Martin

2012-01-01

Purpose. To estimate effective dose and organ equivalent doses of prospective ECG-triggered high-pitch CTCA. Materials and Methods. For dose measurements, an Alderson-Rando phantom equipped with thermoluminescent dosimeters was used. The effective dose was calculated according to ICRP 103. Exposure was performed on a second-generation dual-source scanner (SOMATOM Definition Flash, Siemens Medical Solutions, Germany). The following scan parameters were used: 320 mAs per rotation, 100 and 120 kV, pitch 3.4 for prospectively ECG-triggered high-pitch CTCA, scan range of 13.5 cm, collimation 64 × 2 × 0.6 mm with z-flying focal spot, gantry rotation time 280 ms, and simulated heart rate of 60 beats per minute. Results. Depending on the applied tube potential, the effective whole-body dose of the cardiac scan ranged from 1.1 mSv to 1.6 mSv and from 1.2 to 1.8 mSv for males and females, respectively. The radiosensitive breast tissue in the range of the primary beam caused an increased female-specific effective dose of 8.6%±0.3% compared to males. Decreasing the tube potential, a significant reduction of the effective dose of 35.8% and 36.0% can be achieved for males and females, respectively (P < 0.001). Conclusion. The radiologist and the CT technician should be aware of this new dose-saving strategy to keep the radiation exposure as low as reasonablly achievable.

7. VIEW OF BRINING TANK Newer, concrete model. After drying, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

7. VIEW OF BRINING TANK Newer, concrete model. After drying, skins were rolled in borax and packed into barrels, such as those seen in background. - Sealing Plant, St. George Island, Pribilof Islands, Saint George, Aleutians West Census Area, AK

Total liquid routes and anti-icing liquids.

DOT National Transportation Integrated Search

2013-10-01

INDOT has successfully used salt brine in antiicing efforts as a way to deliver preventative treatment before an event (e.g. bridge deck : frost) occurs. In 2011 INDOT wanted to investigate the use of salt brine in deicing operations. This stud...

Small Scale Multisource Site – Hydrogeology Investigation

EPA Science Inventory

A site impacted by brackish water was evaluated using traditional hydrogeologic and geochemical site characterization techniques. No single, specific source of the brine impacted ground water was identified. However, the extent of the brine impacted ground water was found to be...

Brain blood flow and cardiovascular responses to hot flashes in postmenopausal women

PubMed Central

Lucas, Rebekah A. I.; Ganio, Matthew S.; Pearson, James; Crandall, Craig G.

2012-01-01

Objective This study tested two related hypotheses: 1) that brain blood flow is reduced during the postmenopausal hot flash; and, 2) the magnitude of this reduction in brain blood flow is greater during hot flashes where blood pressure is reduced. Methods Eleven healthy, normotensive, postmenopausal women rested in a temperature-controlled laboratory (~25°C) for approximately 120 minutes while waiting for a hot flash to occur. The onset of a hot flash was objectively identified by an abrupt increase in sternal sweat rate (capacitance hygrometry). Middle cerebral artery blood velocity (MCAv, transcranial Doppler) and mean arterial pressure (Finometer®) were measured continuously. Each hot flash was divided into 8 equal segments and the segment with the largest reduction in MCAv and mean arterial pressure identified for each hot flash. Results Twenty-five hot flashes occurred during the experimental sessions (lasting 6.2 ± 2.8 min, 3 ± 1 hot flashes per participant). Seventy-six percent of hot flashes were accompanied by a clear reduction (greater than 5%) in brain blood flow. For all hot flashes, the average maximum decrease in MCAv was 12 ± 9% (7 ± 6 cm.s−1). This value did not correlate with corresponding changes in mean arterial pressure (R=0.36). Conclusion These findings demonstrate that hot flashes are often accompanied by clear reductions in brain blood flow that do not correspond with acute reductions in mean arterial blood pressure. PMID:23435027