Characterization of airborne float coal dust emitted during continuous mining, longwall mining and belt transport

PubMed Central

Shahan, M.R.; Seaman, C.E.; Beck, T.W.; Colinet, J.F.; Mischler, S.E.

2017-01-01

Float coal dust is produced by various mining methods, carried by ventilating air and deposited on the floor, roof and ribs of mine airways. If deposited, float dust is re-entrained during a methane explosion. Without sufficient inert rock dust quantities, this float coal dust can propagate an explosion throughout mining entries. Consequently, controlling float coal dust is of critical interest to mining operations. Rock dusting, which is the adding of inert material to airway surfaces, is the main control technique currently used by the coal mining industry to reduce the float coal dust explosion hazard. To assist the industry in reducing this hazard, the Pittsburgh Mining Research Division of the U.S. National Institute for Occupational Safety and Health initiated a project to investigate methods and technologies to reduce float coal dust in underground coal mines through prevention, capture and suppression prior to deposition. Field characterization studies were performed to determine quantitatively the sources, types and amounts of dust produced during various coal mining processes. The operations chosen for study were a continuous miner section, a longwall section and a coal-handling facility. For each of these operations, the primary dust sources were confirmed to be the continuous mining machine, longwall shearer and conveyor belt transfer points, respectively. Respirable and total airborne float dust samples were collected and analyzed for each operation, and the ratio of total airborne float coal dust to respirable dust was calculated. During the continuous mining process, the ratio of total airborne float coal dust to respirable dust ranged from 10.3 to 13.8. The ratios measured on the longwall face were between 18.5 and 21.5. The total airborne float coal dust to respirable dust ratio observed during belt transport ranged between 7.5 and 21.8. PMID:28936001

Floating-point system quantization errors in digital control systems

NASA Technical Reports Server (NTRS)

Phillips, C. L.

1973-01-01

The results are reported of research into the effects on system operation of signal quantization in a digital control system. The investigation considered digital controllers (filters) operating in floating-point arithmetic in either open-loop or closed-loop systems. An error analysis technique is developed, and is implemented by a digital computer program that is based on a digital simulation of the system. As an output the program gives the programing form required for minimum system quantization errors (either maximum of rms errors), and the maximum and rms errors that appear in the system output for a given bit configuration. The program can be integrated into existing digital simulations of a system.

The Efficiency and the Scalability of an Explicit Operator on an IBM POWER4 System

NASA Technical Reports Server (NTRS)

Frumkin, Michael; Biegel, Bryan A. (Technical Monitor)

2002-01-01

We present an evaluation of the efficiency and the scalability of an explicit CFD operator on an IBM POWER4 system. The POWER4 architecture exhibits a common trend in HPC architectures: boosting CPU processing power by increasing the number of functional units, while hiding the latency of memory access by increasing the depth of the memory hierarchy. The overall machine performance depends on the ability of the caches-buses-fabric-memory to feed the functional units with the data to be processed. In this study we evaluate the efficiency and scalability of one explicit CFD operator on an IBM POWER4. This operator performs computations at the points of a Cartesian grid and involves a few dozen floating point numbers and on the order of 100 floating point operations per grid point. The computations in all grid points are independent. Specifically, we estimate the efficiency of the RHS operator (SP of NPB) on a single processor as the observed/peak performance ratio. Then we estimate the scalability of the operator on a single chip (2 CPUs), a single MCM (8 CPUs), 16 CPUs, and the whole machine (32 CPUs). Then we perform the same measurements for a chache-optimized version of the RHS operator. For our measurements we use the HPM (Hardware Performance Monitor) counters available on the POWER4. These counters allow us to analyze the obtained performance results.

76 FR 71322 - Taking and Importing Marine Mammals; U.S. Navy Training in the Hawaii Range Complex

Federal Register 2010, 2011, 2012, 2013, 2014

2011-11-17

..., most operationally sound method of initiating a demolition charge on a floating mine or mine at depth...; require building/ deploying an improvised, bulky, floating system for the receiver; and add another 180 ft... charge initiating device are taken to the detonation point. Military forms of C-4 are used as the...

Program Converts VAX Floating-Point Data To UNIX

NASA Technical Reports Server (NTRS)

Alves, Marcos; Chapman, Bruce; Chu, Eugene

1996-01-01

VAX Floating Point to Host Floating Point Conversion (VAXFC) software converts non-ASCII files to unformatted floating-point representation of UNIX machine. This is done by reading bytes bit by bit, converting them to floating-point numbers, then writing results to another file. Useful when data files created by VAX computer must be used on other machines. Written in C language.

Y-MP floating point and Cholesky factorization

NASA Technical Reports Server (NTRS)

Carter, Russell

1991-01-01

The floating point arithmetics implemented in the Cray 2 and Cray Y-MP computer systems are nearly identical, but large scale computations performed on the two systems have exhibited significant differences in accuracy. The difference in accuracy is analyzed for Cholesky factorization algorithm, and it is found that the source of the difference is the subtract magnitude operation of the Cray Y-MP. The results from numerical experiments for a range of problem sizes are presented, and an efficient method for improving the accuracy of the factorization obtained on the Y-MP is presented.

Software Aspects of IEEE Floating-Point Computations for Numerical Applications in High Energy Physics

ScienceCinema

Arnold, Jeffrey

2018-05-14

Floating-point computations are at the heart of much of the computing done in high energy physics. The correctness, speed and accuracy of these computations are of paramount importance. The lack of any of these characteristics can mean the difference between new, exciting physics and an embarrassing correction. This talk will examine practical aspects of IEEE 754-2008 floating-point arithmetic as encountered in HEP applications. After describing the basic features of IEEE floating-point arithmetic, the presentation will cover: common hardware implementations (SSE, x87) techniques for improving the accuracy of summation, multiplication and data interchange compiler options for gcc and icc affecting floating-point operations hazards to be avoided. About the speaker: Jeffrey M Arnold is a Senior Software Engineer in the Intel Compiler and Languages group at Intel Corporation. He has been part of the Digital->Compaq->Intel compiler organization for nearly 20 years; part of that time, he worked on both low- and high-level math libraries. Prior to that, he was in the VMS Engineering organization at Digital Equipment Corporation. In the late 1980s, Jeff spent 2½ years at CERN as part of the CERN/Digital Joint Project. In 2008, he returned to CERN to spent 10 weeks working with CERN/openlab. Since that time, he has returned to CERN multiple times to teach at openlab workshops and consult with various LHC experiments. Jeff received his Ph.D. in physics from Case Western Reserve University.

LDPC decoder with a limited-precision FPGA-based floating-point multiplication coprocessor

NASA Astrophysics Data System (ADS)

Moberly, Raymond; O'Sullivan, Michael; Waheed, Khurram

2007-09-01

Implementing the sum-product algorithm, in an FPGA with an embedded processor, invites us to consider a tradeoff between computational precision and computational speed. The algorithm, known outside of the signal processing community as Pearl's belief propagation, is used for iterative soft-decision decoding of LDPC codes. We determined the feasibility of a coprocessor that will perform product computations. Our FPGA-based coprocessor (design) performs computer algebra with significantly less precision than the standard (e.g. integer, floating-point) operations of general purpose processors. Using synthesis, targeting a 3,168 LUT Xilinx FPGA, we show that key components of a decoder are feasible and that the full single-precision decoder could be constructed using a larger part. Soft-decision decoding by the iterative belief propagation algorithm is impacted both positively and negatively by a reduction in the precision of the computation. Reducing precision reduces the coding gain, but the limited-precision computation can operate faster. A proposed solution offers custom logic to perform computations with less precision, yet uses the floating-point format to interface with the software. Simulation results show the achievable coding gain. Synthesis results help theorize the the full capacity and performance of an FPGA-based coprocessor.

Floating electrode dielectrophoresis.

PubMed

Golan, Saar; Elata, David; Orenstein, Meir; Dinnar, Uri

2006-12-01

In practice, dielectrophoresis (DEP) devices are based on micropatterned electrodes. When subjected to applied voltages, the electrodes generate nonuniform electric fields that are necessary for the DEP manipulation of particles. In this study, electrically floating electrodes are used in DEP devices. It is demonstrated that effective DEP forces can be achieved by using floating electrodes. Additionally, DEP forces generated by floating electrodes are different from DEP forces generated by excited electrodes. The floating electrodes' capabilities are explained theoretically by calculating the electric field gradients and demonstrated experimentally by using test-devices. The test-devices show that floating electrodes can be used to collect erythrocytes (red blood cells). DEP devices which contain many floating electrodes ought to have fewer connections to external signal sources. Therefore, the use of floating electrodes may considerably facilitate the fabrication and operation of DEP devices. It can also reduce device dimensions. However, the key point is that DEP devices can integrate excited electrodes fabricated by microtechnology processes and floating electrodes fabricated by nanotechnology processes. Such integration is expected to promote the use of DEP devices in the manipulation of nanoparticles.

Floating shoulders: Clinical and radiographic analysis at a mean follow-up of 11 years

PubMed Central

Pailhes, ReÌ gis; Bonnevialle, Nicolas; Laffosse, JeanMichel; Tricoire, JeanLouis; Cavaignac, Etienne; Chiron, Philippe

2013-01-01

Context: The floating shoulder (FS) is an uncommon injury, which can be managed conservatively or surgically. The therapeutic option remains controversial. Aims: The goal of our study was to evaluate the long-term results and to identify predictive factors of functional outcomes. Settings and Design: Retrospective monocentric study. Materials and Methods: Forty consecutive FS were included (24 nonoperated and 16 operated) from 1984 to 2009. Clinical results were assessed with Simple Shoulder Test (SST), Oxford Shoulder Score (OSS), Single Assessment Numeric Evaluation (SANE), Short Form-12 (SF12), Disabilities of the Arm Shoulder and Hand score (DASH), and Constant score (CST). Plain radiographs were reviewed to evaluate secondary displacement, fracture healing, and modification of the lateral offset of the gleno-humeral joint (chest X-rays). New radiographs were made to evaluate osteoarthritis during follow-up. Statistical Analysis Used: T-test, Mann-Whitney test, and the Pearson's correlation coefficient were used. The significance level was set at 0.05. Results: At mean follow-up of 135 months (range 12-312), clinical results were satisfactory regarding different mean scores: SST 10.5 points, OSS 14 points, SANE 81%, SF12 (50 points and 60 points), DASH 14.5 points and CST 84 points. There were no significant differences between operative and non-operative groups. However, the loss of lateral offset influenced the results negatively. Osteoarthritis was diagnosed in five patients (12.5%) without correlation to fracture patterns and type of treatment. Conclusions: This study advocates that floating shoulder may be treated conservatively and surgically with satisfactory clinical long-term outcomes. However, the loss of gleno-humeral lateral offset should be evaluated carefully before taking a therapeutic option. PMID:23960364

Efficient volume computation for three-dimensional hexahedral cells

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dukowicz, J.K.

1988-02-01

Currently, algorithms for computing the volume of hexahedral cells with ''ruled'' surfaces require a minimum of 122 FLOPs (floating point operations) per cell. A new algorithm is described which reduces the operation count to 57 FLOPs per cell. copyright 1988 Academic Press, Inc.

Multi-input and binary reproducible, high bandwidth floating point adder in a collective network

DOEpatents

Chen, Dong; Eisley, Noel A.; Heidelberger, Philip; Steinmacher-Burow, Burkhard

2016-11-15

To add floating point numbers in a parallel computing system, a collective logic device receives the floating point numbers from computing nodes. The collective logic devices converts the floating point numbers to integer numbers. The collective logic device adds the integer numbers and generating a summation of the integer numbers. The collective logic device converts the summation to a floating point number. The collective logic device performs the receiving, the converting the floating point numbers, the adding, the generating and the converting the summation in one pass. One pass indicates that the computing nodes send inputs only once to the collective logic device and receive outputs only once from the collective logic device.

Fast and efficient compression of floating-point data.

PubMed

Lindstrom, Peter; Isenburg, Martin

2006-01-01

Large scale scientific simulation codes typically run on a cluster of CPUs that write/read time steps to/from a single file system. As data sets are constantly growing in size, this increasingly leads to I/O bottlenecks. When the rate at which data is produced exceeds the available I/O bandwidth, the simulation stalls and the CPUs are idle. Data compression can alleviate this problem by using some CPU cycles to reduce the amount of data needed to be transfered. Most compression schemes, however, are designed to operate offline and seek to maximize compression, not throughput. Furthermore, they often require quantizing floating-point values onto a uniform integer grid, which disqualifies their use in applications where exact values must be retained. We propose a simple scheme for lossless, online compression of floating-point data that transparently integrates into the I/O of many applications. A plug-in scheme for data-dependent prediction makes our scheme applicable to a wide variety of data used in visualization, such as unstructured meshes, point sets, images, and voxel grids. We achieve state-of-the-art compression rates and speeds, the latter in part due to an improved entropy coder. We demonstrate that this significantly accelerates I/O throughput in real simulation runs. Unlike previous schemes, our method also adapts well to variable-precision floating-point and integer data.

Selection of floating-point or fixed-point for adaptive noise canceller in somatosensory evoked potential measurement.

PubMed

Shen, Chongfei; Liu, Hongtao; Xie, Xb; Luk, Keith Dk; Hu, Yong

2007-01-01

Adaptive noise canceller (ANC) has been used to improve signal to noise ratio (SNR) of somsatosensory evoked potential (SEP). In order to efficiently apply the ANC in hardware system, fixed-point algorithm based ANC can achieve fast, cost-efficient construction, and low-power consumption in FPGA design. However, it is still questionable whether the SNR improvement performance by fixed-point algorithm is as good as that by floating-point algorithm. This study is to compare the outputs of ANC by floating-point and fixed-point algorithm ANC when it was applied to SEP signals. The selection of step-size parameter (micro) was found different in fixed-point algorithm from floating-point algorithm. In this simulation study, the outputs of fixed-point ANC showed higher distortion from real SEP signals than that of floating-point ANC. However, the difference would be decreased with increasing micro value. In the optimal selection of micro, fixed-point ANC can get as good results as floating-point algorithm.

A performance comparison of the IBM RS/6000 and the Astronautics ZS-1

DOE Office of Scientific and Technical Information (OSTI.GOV)

Smith, W.M.; Abraham, S.G.; Davidson, E.S.

1991-01-01

Concurrent uniprocessor architectures, of which vector and superscalar are two examples, are designed to capitalize on fine-grain parallelism. The authors have developed a performance evaluation method for comparing and improving these architectures, and in this article they present the methodology and a detailed case study of two machines. The runtime of many programs is dominated by time spent in loop constructs - for example, Fortran Do-loops. Loops generally comprise two logical processes: The access process generates addresses for memory operations while the execute process operates on floating-point data. Memory access patterns typically can be generated independently of the data inmore » the execute process. This independence allows the access process to slip ahead, thereby hiding memory latency. The IBM 360/91 was designed in 1967 to achieve slip dynamically, at runtime. One CPU unit executes integer operations while another handles floating-point operations. Other machines, including the VAX 9000 and the IBM RS/6000, use a similar approach.« less

Multi-input and binary reproducible, high bandwidth floating point adder in a collective network

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chen, Dong; Eisley, Noel A; Heidelberger, Philip

To add floating point numbers in a parallel computing system, a collective logic device receives the floating point numbers from computing nodes. The collective logic devices converts the floating point numbers to integer numbers. The collective logic device adds the integer numbers and generating a summation of the integer numbers. The collective logic device converts the summation to a floating point number. The collective logic device performs the receiving, the converting the floating point numbers, the adding, the generating and the converting the summation in one pass. One pass indicates that the computing nodes send inputs only once to themore » collective logic device and receive outputs only once from the collective logic device.« less

78 FR 46258 - Drawbridge Operation Regulation Lake Washington, Seattle, WA

Federal Register 2010, 2011, 2012, 2013, 2014

2013-07-31

... Operation Regulation Lake Washington, Seattle, WA AGENCY: Coast Guard, DHS. ACTION: Notice of deviation from... that governs the Evergreen Point Floating Bridge (State Route 520 across Lake Washington) at Seattle... Route 520 across Lake Washington) remain closed to vessel traffic to facilitate safe passage of...

Environment parameters and basic functions for floating-point computation

NASA Technical Reports Server (NTRS)

Brown, W. S.; Feldman, S. I.

1978-01-01

A language-independent proposal for environment parameters and basic functions for floating-point computation is presented. Basic functions are proposed to analyze, synthesize, and scale floating-point numbers. The model provides a small set of parameters and a small set of axioms along with sharp measures of roundoff error. The parameters and functions can be used to write portable and robust codes that deal intimately with the floating-point representation. Subject to underflow and overflow constraints, a number can be scaled by a power of the floating-point radix inexpensively and without loss of precision. A specific representation for FORTRAN is included.

Shift-connected SIMD array architectures for digital optical computing systems, with algorithms for numerical transforms and partial differential equations

NASA Astrophysics Data System (ADS)

Drabik, Timothy J.; Lee, Sing H.

1986-11-01

The intrinsic parallelism characteristics of easily realizable optical SIMD arrays prompt their present consideration in the implementation of highly structured algorithms for the numerical solution of multidimensional partial differential equations and the computation of fast numerical transforms. Attention is given to a system, comprising several spatial light modulators (SLMs), an optical read/write memory, and a functional block, which performs simple, space-invariant shifts on images with sufficient flexibility to implement the fastest known methods for partial differential equations as well as a wide variety of numerical transforms in two or more dimensions. Either fixed or floating-point arithmetic may be used. A performance projection of more than 1 billion floating point operations/sec using SLMs with 1000 x 1000-resolution and operating at 1-MHz frame rates is made.

Identification of mothball powder composition by float tests and melting point tests.

PubMed

Tang, Ka Yuen

2018-07-01

The aim of the study was to identify the composition, as either camphor, naphthalene, or paradichlorobenzene, of mothballs in the form of powder or tiny fragments by float tests and melting point tests. Naphthalene, paradichlorobenzene and camphor mothballs were blended into powder and tiny fragments (with sizes <1/10 of the size of an intact mothball). In the float tests, the mothball powder and tiny fragments were placed in water, saturated salt solution and 50% dextrose solution (D50), and the extent to which they floated or sank in the liquids was observed. In the melting point tests, the mothball powder and tiny fragments were placed in hot water with a temperature between 53 and 80 °C, and the extent to which they melted was observed. Both the float and melting point tests were then repeated using intact mothballs. Three emergency physicians blinded to the identities of samples and solutions visually evaluated each sample. In the float tests, paradichlorobenzene powder partially floated and partially sank in all three liquids, while naphthalene powder partially floated and partially sank in water. Naphthalene powder did not sink in D50 or saturated salt solution. Camphor powder floated in all three liquids. Float tests identified the compositions of intact mothball accurately. In the melting point tests, paradichlorobenzene powder melted completely in hot water within 1 min while naphthalene powder and camphor powder did not melt. The melted portions of paradichlorobenzene mothballs were sometimes too small to be observed in 1 min but the mothballs either partially or completely melted in 5 min. Both camphor and naphthalene intact mothballs did not melt in hot water. For mothball powder, the melting point tests were more accurate than the float tests in differentiating between paradichlorobenzene and non-paradichlorobenzene (naphthalene or camphor). For intact mothballs, float tests performed better than melting point tests. Float tests can identify camphor mothballs but melting point tests cannot. We suggest melting point tests for identifying mothball powder and tiny fragments while float tests are recommended for intact mothball and large fragments.

Paranoia.Ada: A diagnostic program to evaluate Ada floating-point arithmetic

NASA Technical Reports Server (NTRS)

Hjermstad, Chris

1986-01-01

Many essential software functions in the mission critical computer resource application domain depend on floating point arithmetic. Numerically intensive functions associated with the Space Station project, such as emphemeris generation or the implementation of Kalman filters, are likely to employ the floating point facilities of Ada. Paranoia.Ada appears to be a valuabe program to insure that Ada environments and their underlying hardware exhibit the precision and correctness required to satisfy mission computational requirements. As a diagnostic tool, Paranoia.Ada reveals many essential characteristics of an Ada floating point implementation. Equipped with such knowledge, programmers need not tremble before the complex task of floating point computation.

40 CFR 63.653 - Monitoring, recordkeeping, and implementation plan for emissions averaging.

Code of Federal Regulations, 2010 CFR

2010-07-01

...) For each emission point included in an emissions average, the owner or operator shall perform testing, monitoring, recordkeeping, and reporting equivalent to that required for Group 1 emission points complying... internal floating roof, external roof, or a closed vent system with a control device, as appropriate to the...

Bifurcated method and apparatus for floating point addition with decreased latency time

DOEpatents

Farmwald, Paul M.

1987-01-01

Apparatus for decreasing the latency time associated with floating point addition and subtraction in a computer, using a novel bifurcated, pre-normalization/post-normalization approach that distinguishes between differences of floating point exponents.

Bearing Capacity of Floating Ice Sheets under Short-Term Loads: Over-Sea-Ice Traverse from McMurdo Station to Marble Point

DTIC Science & Technology

2015-01-01

crafts on floating ice sheets near McMurdo, Antarctica (Katona and Vaudrey 1973; Katona 1974; Vaudrey 1977). To comply with the first criterion, one...Nomographs for operating wheeled aircraft on sea- ice runways: McMurdo Station, Antarctica . In Proceedings of the Offshore Mechanics and Arctic Engineering... Ice Thickness Requirements for Vehicles and Heavy Equipment at McMurdo Station, Antarctica . CRREL Project Report 04- 09, “Safe Sea Ice for Vehicle

NULL Convention Floating Point Multiplier

PubMed Central

Ramachandran, Seshasayanan

2015-01-01

Floating point multiplication is a critical part in high dynamic range and computational intensive digital signal processing applications which require high precision and low power. This paper presents the design of an IEEE 754 single precision floating point multiplier using asynchronous NULL convention logic paradigm. Rounding has not been implemented to suit high precision applications. The novelty of the research is that it is the first ever NULL convention logic multiplier, designed to perform floating point multiplication. The proposed multiplier offers substantial decrease in power consumption when compared with its synchronous version. Performance attributes of the NULL convention logic floating point multiplier, obtained from Xilinx simulation and Cadence, are compared with its equivalent synchronous implementation. PMID:25879069

NULL convention floating point multiplier.

PubMed

Albert, Anitha Juliette; Ramachandran, Seshasayanan

2015-01-01

Floating point multiplication is a critical part in high dynamic range and computational intensive digital signal processing applications which require high precision and low power. This paper presents the design of an IEEE 754 single precision floating point multiplier using asynchronous NULL convention logic paradigm. Rounding has not been implemented to suit high precision applications. The novelty of the research is that it is the first ever NULL convention logic multiplier, designed to perform floating point multiplication. The proposed multiplier offers substantial decrease in power consumption when compared with its synchronous version. Performance attributes of the NULL convention logic floating point multiplier, obtained from Xilinx simulation and Cadence, are compared with its equivalent synchronous implementation.

Fixed-Rate Compressed Floating-Point Arrays.

PubMed

Lindstrom, Peter

2014-12-01

Current compression schemes for floating-point data commonly take fixed-precision values and compress them to a variable-length bit stream, complicating memory management and random access. We present a fixed-rate, near-lossless compression scheme that maps small blocks of 4(d) values in d dimensions to a fixed, user-specified number of bits per block, thereby allowing read and write random access to compressed floating-point data at block granularity. Our approach is inspired by fixed-rate texture compression methods widely adopted in graphics hardware, but has been tailored to the high dynamic range and precision demands of scientific applications. Our compressor is based on a new, lifted, orthogonal block transform and embedded coding, allowing each per-block bit stream to be truncated at any point if desired, thus facilitating bit rate selection using a single compression scheme. To avoid compression or decompression upon every data access, we employ a software write-back cache of uncompressed blocks. Our compressor has been designed with computational simplicity and speed in mind to allow for the possibility of a hardware implementation, and uses only a small number of fixed-point arithmetic operations per compressed value. We demonstrate the viability and benefits of lossy compression in several applications, including visualization, quantitative data analysis, and numerical simulation.

Floating point arithmetic in future supercomputers

NASA Technical Reports Server (NTRS)

Bailey, David H.; Barton, John T.; Simon, Horst D.; Fouts, Martin J.

1989-01-01

Considerations in the floating-point design of a supercomputer are discussed. Particular attention is given to word size, hardware support for extended precision, format, and accuracy characteristics. These issues are discussed from the perspective of the Numerical Aerodynamic Simulation Systems Division at NASA Ames. The features believed to be most important for a future supercomputer floating-point design include: (1) a 64-bit IEEE floating-point format with 11 exponent bits, 52 mantissa bits, and one sign bit and (2) hardware support for reasonably fast double-precision arithmetic.

Defining the IEEE-854 floating-point standard in PVS

NASA Technical Reports Server (NTRS)

Miner, Paul S.

1995-01-01

A significant portion of the ANSI/IEEE-854 Standard for Radix-Independent Floating-Point Arithmetic is defined in PVS (Prototype Verification System). Since IEEE-854 is a generalization of the ANSI/IEEE-754 Standard for Binary Floating-Point Arithmetic, the definition of IEEE-854 in PVS also formally defines much of IEEE-754. This collection of PVS theories provides a basis for machine checked verification of floating-point systems. This formal definition illustrates that formal specification techniques are sufficiently advanced that is is reasonable to consider their use in the development of future standards.

Rapid Prototyping in PVS

NASA Technical Reports Server (NTRS)

Munoz, Cesar A.; Butler, Ricky (Technical Monitor)

2003-01-01

PVSio is a conservative extension to the PVS prelude library that provides basic input/output capabilities to the PVS ground evaluator. It supports rapid prototyping in PVS by enhancing the specification language with built-in constructs for string manipulation, floating point arithmetic, and input/output operations.

A preliminary study of molecular dynamics on reconfigurable computers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wolinski, C.; Trouw, F. R.; Gokhale, M.

2003-01-01

In this paper we investigate the performance of platform FPGAs on a compute-intensive, floating-point-intensive supercomputing application, Molecular Dynamics (MD). MD is a popular simulation technique to track interacting particles through time by integrating their equations of motion. One part of the MD algorithm was implemented using the Fabric Generator (FG)[l I ] and mapped onto several reconfigurable logic arrays. FG is a Java-based toolset that greatly accelerates construction of the fabrics from an abstract technology independent representation. Our experiments used technology-independent IEEE 32-bit floating point operators so that the design could be easily re-targeted. Experiments were performed using both non-pipelinedmore » and pipelined floating point modules. We present results for the Altera Excalibur ARM System on a Programmable Chip (SoPC), the Altera Strath EPlS80, and the Xilinx Virtex-N Pro 2VP.50. The best results obtained were 5.69 GFlops at 8OMHz(Altera Strath EPlS80), and 4.47 GFlops at 82 MHz (Xilinx Virtex-II Pro 2VF50). Assuming a lOWpower budget, these results compare very favorably to a 4Gjlop/40Wprocessing/power rate for a modern Pentium, suggesting that reconfigurable logic can achieve high performance at low power on jloating-point-intensivea pplications.« less

Optimization of block-floating-point realizations for digital controllers with finite-word-length considerations.

PubMed

Wu, Jun; Hu, Xie-he; Chen, Sheng; Chu, Jian

2003-01-01

The closed-loop stability issue of finite-precision realizations was investigated for digital controllers implemented in block-floating-point format. The controller coefficient perturbation was analyzed resulting from using finite word length (FWL) block-floating-point representation scheme. A block-floating-point FWL closed-loop stability measure was derived which considers both the dynamic range and precision. To facilitate the design of optimal finite-precision controller realizations, a computationally tractable block-floating-point FWL closed-loop stability measure was then introduced and the method of computing the value of this measure for a given controller realization was developed. The optimal controller realization is defined as the solution that maximizes the corresponding measure, and a numerical optimization approach was adopted to solve the resulting optimal realization problem. A numerical example was used to illustrate the design procedure and to compare the optimal controller realization with the initial realization.

Apparatus and method for implementing power saving techniques when processing floating point values

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kim, Young Moon; Park, Sang Phill

An apparatus and method are described for reducing power when reading and writing graphics data. For example, one embodiment of an apparatus comprises: a graphics processor unit (GPU) to process graphics data including floating point data; a set of registers, at least one of the registers of the set partitioned to store the floating point data; and encode/decode logic to reduce a number of binary 1 values being read from the at least one register by causing a specified set of bit positions within the floating point data to be read out as 0s rather than 1s.

Automatic Estimation of Verified Floating-Point Round-Off Errors via Static Analysis

NASA Technical Reports Server (NTRS)

Moscato, Mariano; Titolo, Laura; Dutle, Aaron; Munoz, Cesar A.

2017-01-01

This paper introduces a static analysis technique for computing formally verified round-off error bounds of floating-point functional expressions. The technique is based on a denotational semantics that computes a symbolic estimation of floating-point round-o errors along with a proof certificate that ensures its correctness. The symbolic estimation can be evaluated on concrete inputs using rigorous enclosure methods to produce formally verified numerical error bounds. The proposed technique is implemented in the prototype research tool PRECiSA (Program Round-o Error Certifier via Static Analysis) and used in the verification of floating-point programs of interest to NASA.

Numerical aerodynamic simulation facility preliminary study: Executive study

NASA Technical Reports Server (NTRS)

1977-01-01

A computing system was designed with the capability of providing an effective throughput of one billion floating point operations per second for three dimensional Navier-Stokes codes. The methodology used in defining the baseline design, and the major elements of the numerical aerodynamic simulation facility are described.

Memory operations in Au nanoparticle single-electron transistors with floating gate electrodes

NASA Astrophysics Data System (ADS)

Azuma, Yasuo; Sakamoto, Masanori; Teranishi, Toshiharu; Majima, Yutaka

2016-11-01

Floating gate memory operations are demonstrated in a single-electron transistor (SET) fabricated by a chemical assembly using the Au nanogap electrodes and the chemisorbed Au nanoparticles. By applying pulse voltages to the control gate, phase shifts were clearly and stably observed both in the Coulomb oscillations and in the Coulomb diamonds. Writing and erasing operations on the floating gate memory were reproducibly observed, and the charges on the floating gate electrodes were maintained for at least 12 h. By considering the capacitance of the floating gate electrode, the number of electrons in the floating gate electrode was estimated as 260. Owing to the stability of the fabricated SET, these writing and erasing operations on the floating gate memory can be applied to reconfigurable SET circuits fabricated by a chemically assembled technique.

Observations of Transient ISS Floating Potential Variations During High Voltage Solar Array Operations

NASA Technical Reports Server (NTRS)

Willis, Emily M.; Minow, Joseph I.; Parker, Linda N.; Pour, Maria Z. A.; Swenson, Charles; Nishikawa, Ken-ichi; Krause, Linda Habash

2016-01-01

The International Space Station (ISS) continues to be a world-class space research laboratory after over 15 years of operations, and it has proven to be a fantastic resource for observing spacecraft floating potential variations related to high voltage solar array operations in Low Earth Orbit (LEO). Measurements of the ionospheric electron density and temperature along the ISS orbit and variations in the ISS floating potential are obtained from the Floating Potential Measurement Unit (FPMU). In particular, rapid variations in ISS floating potential during solar array operations on time scales of tens of milliseconds can be recorded due to the 128 Hz sample rate of the Floating Potential Probe (FPP) pro- viding interesting insight into high voltage solar array interaction with the space plasma environment. Comparing the FPMU data with the ISS operations timeline and solar array data provides a means for correlating some of the more complex and interesting transient floating potential variations with mission operations. These complex variations are not reproduced by current models and require further study to understand the underlying physical processes. In this paper we present some of the floating potential transients observed over the past few years along with the relevant space environment parameters and solar array operations data.

Floating-point performance of ARM cores and their efficiency in classical molecular dynamics

NASA Astrophysics Data System (ADS)

Nikolskiy, V.; Stegailov, V.

2016-02-01

Supercomputing of the exascale era is going to be inevitably limited by power efficiency. Nowadays different possible variants of CPU architectures are considered. Recently the development of ARM processors has come to the point when their floating point performance can be seriously considered for a range of scientific applications. In this work we present the analysis of the floating point performance of the latest ARM cores and their efficiency for the algorithms of classical molecular dynamics.

The use of ZFP lossy floating point data compression in tornado-resolving thunderstorm simulations

NASA Astrophysics Data System (ADS)

Orf, L.

2017-12-01

In the field of atmospheric science, numerical models are used to produce forecasts of weather and climate and serve as virtual laboratories for scientists studying atmospheric phenomena. In both operational and research arenas, atmospheric simulations exploiting modern supercomputing hardware can produce a tremendous amount of data. During model execution, the transfer of floating point data from memory to the file system is often a significant bottleneck where I/O can dominate wallclock time. One way to reduce the I/O footprint is to compress the floating point data, which reduces amount of data saved to the file system. In this presentation we introduce LOFS, a file system developed specifically for use in three-dimensional numerical weather models that are run on massively parallel supercomputers. LOFS utilizes the core (in-memory buffered) HDF5 driver and includes compression options including ZFP, a lossy floating point data compression algorithm. ZFP offers several mechanisms for specifying the amount of lossy compression to be applied to floating point data, including the ability to specify the maximum absolute error allowed in each compressed 3D array. We explore different maximum error tolerances in a tornado-resolving supercell thunderstorm simulation for model variables including cloud and precipitation, temperature, wind velocity and vorticity magnitude. We find that average compression ratios exceeding 20:1 in scientifically interesting regions of the simulation domain produce visually identical results to uncompressed data in visualizations and plots. Since LOFS splits the model domain across many files, compression ratios for a given error tolerance can be compared across different locations within the model domain. We find that regions of high spatial variability (which tend to be where scientifically interesting things are occurring) show the lowest compression ratios, whereas regions of the domain with little spatial variability compress extremely well. We observe that the overhead for compressing data with ZFP is low, and that compressing data in memory reduces the amount of memory overhead needed to store the virtual files before they are flushed to disk.

Applying n-bit floating point numbers and integers, and the n-bit filter of HDF5 to reduce file sizes of remote sensing products in memory-sensitive environments

NASA Astrophysics Data System (ADS)

Zinke, Stephan

2017-02-01

Memory sensitive applications for remote sensing data require memory-optimized data types in remote sensing products. Hierarchical Data Format version 5 (HDF5) offers user defined floating point numbers and integers and the n-bit filter to create data types optimized for memory consumption. The European Organisation for the Exploitation of Meteorological Satellites (EUMETSAT) applies a compaction scheme to the disseminated products of the Day and Night Band (DNB) data of Suomi National Polar-orbiting Partnership (S-NPP) satellite's instrument Visible Infrared Imager Radiometer Suite (VIIRS) through the EUMETSAT Advanced Retransmission Service, converting the original 32 bits floating point numbers to user defined floating point numbers in combination with the n-bit filter for the radiance dataset of the product. The radiance dataset requires a floating point representation due to the high dynamic range of the DNB. A compression factor of 1.96 is reached by using an automatically determined exponent size and an 8 bits trailing significand and thus reducing the bandwidth requirements for dissemination. It is shown how the parameters needed for user defined floating point numbers are derived or determined automatically based on the data present in a product.

NAS technical summaries: Numerical aerodynamic simulation program, March 1991 - February 1992

NASA Technical Reports Server (NTRS)

1992-01-01

NASA created the Numerical Aerodynamic Simulation (NAS) Program in 1987 to focus resources on solving critical problems in aeroscience and related disciplines by utilizing the power of the most advanced supercomputers available. The NAS Program provides scientists with the necessary computing power to solve today's most demanding computational fluid dynamics problems and serves as a pathfinder in integrating leading-edge supercomputing technologies, thus benefiting other supercomputer centers in Government and industry. This report contains selected scientific results from the 1991-92 NAS Operational Year, March 4, 1991 to March 3, 1992, which is the fifth year of operation. During this year, the scientific community was given access to a Cray-2 and a Cray Y-MP. The Cray-2, the first generation supercomputer, has four processors, 256 megawords of central memory, and a total sustained speed of 250 million floating point operations per second. The Cray Y-MP, the second generation supercomputer, has eight processors and a total sustained speed of one billion floating point operations per second. Additional memory was installed this year, doubling capacity from 128 to 256 megawords of solid-state storage-device memory. Because of its higher performance, the Cray Y-MP delivered approximately 77 percent of the total number of supercomputer hours used during this year.

[Controlled observation of the efficacy between floating acupuncture at Tianying point and warm-needling therapy for supraspinous ligament injury].

PubMed

Li, Xin-Wei; Shao, Xiao-Mei; Tan, Ke-Ping; Fang, Jian-Qiao

2013-04-01

To compare the efficacy difference in the treatment of supraspinous ligament injury between floating acupuncture at Tianying point and the conventional warm needling therapy. Ninety patients were randomized into a floating acupuncture group and a warm needling group, 45 cases in each one. In the floating acupuncture group, the floating needling technique was adopted at Tianying point. In the warm needling group, the conventional warm needling therapy was applied at Tianying point as the chief point in the prescription. The treatment was given 3 times a week and 6 treatments made one session. The visual analogue scale (VAS) was adopted for pain comparison before and after treatment of the patients in two groups and the efficacy in two groups were assessed. The curative and remarkably effective rate was 81.8% (36/44) in the floating acupuncture group and the total effective rate was 95.5% (42/44), which were superior to 44.2% (19/43) and 79.1% (34/43) in the warm needling group separately (P < 0.01, P < 0.05). VAS score was lower as compared with that before treatment of the patients in two groups (both P < 0.01) and the score in the floating acupuncture group was lower than that in the warm needling group after treatment (P < 0.01). Thirty-six cases were cured and remarkably effective in the floating acupuncture group after treatment, in which 28 cases were cured and remarkably effective in 3 treatments, accounting for 77.8 (28/36), which was apparently higher than 26.3 (5/19) in the warm-needling group (P < 0.01). The floating acupuncture at Tianying point achieves the quick and definite efficacy on supraspinous ligament injury and presents the apparent analgesic effect. The efficacy is superior to the conventional warm-needling therapy.

Hydrodynamic and Aerodynamic Tests of Models of Floats for Single-float Seaplanes NACA Models 41-D, 41-E, 61-A, 73, and 73-A

NASA Technical Reports Server (NTRS)

Parkinson, J B; HOUSE R O

1938-01-01

Tests were made in the NACA tank and in the NACA 7 by 10 foot wind tunnel on two models of transverse step floats and three models of pointed step floats considered to be suitable for use with single float seaplanes. The object of the program was the reduction of water resistance and spray of single float seaplanes without reducing the angle of dead rise believed to be necessary for the satisfactory absorption of the shock loads. The results indicated that all the models have less resistance and spray than the model of the Mark V float and that the pointed step floats are somewhat superior to the transverse step floats in these respects. Models 41-D, 61-A, and 73 were tested by the general method over a wide range of loads and speeds. The results are presented in the form of curves and charts for use in design calculations.

Recommended Practice for Use of Emissive Probes in Electric Propulsion Testing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sheehan, J. P.; Raitses, Yevgeny; Hershkowitz, Noah

Here, this article provides recommended methods for building, operating, and taking plasma potential measurements from electron-emitting probes in electric propulsion devices, including Hall thrusters, gridded ion engines, and others. The two major techniques, the floating point technique and the inflection point technique, are described in detail as well as calibration and error-reduction methods. The major heating methods are described as well as the various considerations for emissive probe construction. Lastly, special considerations for electric propulsion plasmas are addressed, including high-energy densities, ion flows, magnetic fields, and potential fluctuations. Recommendations for probe design and operation are provided.

Recommended Practice for Use of Emissive Probes in Electric Propulsion Testing

DOE PAGES

Sheehan, J. P.; Raitses, Yevgeny; Hershkowitz, Noah; ...

2016-11-03

Here, this article provides recommended methods for building, operating, and taking plasma potential measurements from electron-emitting probes in electric propulsion devices, including Hall thrusters, gridded ion engines, and others. The two major techniques, the floating point technique and the inflection point technique, are described in detail as well as calibration and error-reduction methods. The major heating methods are described as well as the various considerations for emissive probe construction. Lastly, special considerations for electric propulsion plasmas are addressed, including high-energy densities, ion flows, magnetic fields, and potential fluctuations. Recommendations for probe design and operation are provided.

Reproducibility of neuroimaging analyses across operating systems

PubMed Central

Glatard, Tristan; Lewis, Lindsay B.; Ferreira da Silva, Rafael; Adalat, Reza; Beck, Natacha; Lepage, Claude; Rioux, Pierre; Rousseau, Marc-Etienne; Sherif, Tarek; Deelman, Ewa; Khalili-Mahani, Najmeh; Evans, Alan C.

2015-01-01

Neuroimaging pipelines are known to generate different results depending on the computing platform where they are compiled and executed. We quantify these differences for brain tissue classification, fMRI analysis, and cortical thickness (CT) extraction, using three of the main neuroimaging packages (FSL, Freesurfer and CIVET) and different versions of GNU/Linux. We also identify some causes of these differences using library and system call interception. We find that these packages use mathematical functions based on single-precision floating-point arithmetic whose implementations in operating systems continue to evolve. While these differences have little or no impact on simple analysis pipelines such as brain extraction and cortical tissue classification, their accumulation creates important differences in longer pipelines such as subcortical tissue classification, fMRI analysis, and cortical thickness extraction. With FSL, most Dice coefficients between subcortical classifications obtained on different operating systems remain above 0.9, but values as low as 0.59 are observed. Independent component analyses (ICA) of fMRI data differ between operating systems in one third of the tested subjects, due to differences in motion correction. With Freesurfer and CIVET, in some brain regions we find an effect of build or operating system on cortical thickness. A first step to correct these reproducibility issues would be to use more precise representations of floating-point numbers in the critical sections of the pipelines. The numerical stability of pipelines should also be reviewed. PMID:25964757

Reproducibility of neuroimaging analyses across operating systems.

PubMed

Glatard, Tristan; Lewis, Lindsay B; Ferreira da Silva, Rafael; Adalat, Reza; Beck, Natacha; Lepage, Claude; Rioux, Pierre; Rousseau, Marc-Etienne; Sherif, Tarek; Deelman, Ewa; Khalili-Mahani, Najmeh; Evans, Alan C

2015-01-01

Neuroimaging pipelines are known to generate different results depending on the computing platform where they are compiled and executed. We quantify these differences for brain tissue classification, fMRI analysis, and cortical thickness (CT) extraction, using three of the main neuroimaging packages (FSL, Freesurfer and CIVET) and different versions of GNU/Linux. We also identify some causes of these differences using library and system call interception. We find that these packages use mathematical functions based on single-precision floating-point arithmetic whose implementations in operating systems continue to evolve. While these differences have little or no impact on simple analysis pipelines such as brain extraction and cortical tissue classification, their accumulation creates important differences in longer pipelines such as subcortical tissue classification, fMRI analysis, and cortical thickness extraction. With FSL, most Dice coefficients between subcortical classifications obtained on different operating systems remain above 0.9, but values as low as 0.59 are observed. Independent component analyses (ICA) of fMRI data differ between operating systems in one third of the tested subjects, due to differences in motion correction. With Freesurfer and CIVET, in some brain regions we find an effect of build or operating system on cortical thickness. A first step to correct these reproducibility issues would be to use more precise representations of floating-point numbers in the critical sections of the pipelines. The numerical stability of pipelines should also be reviewed.

Algorithm XXX : functions to support the IEEE standard for binary floating-point arithmetic.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cody, W. J.; Mathematics and Computer Science

1993-12-01

This paper describes C programs for the support functions copysign(x,y), logb(x), scalb(x,n), nextafter(x,y), finite(x), and isnan(x) recommended in the Appendix to the IEEE Standard for Binary Floating-Point Arithmetic. In the case of logb, the modified definition given in the later IEEE Standard for Radix-Independent Floating-Point Arithmetic is followed. These programs should run without modification on most systems conforming to the binary standard.

Numerical Integration with Graphical Processing Unit for QKD Simulation

DTIC Science & Technology

2014-03-27

Windows system application programming interface (API) timer. The problem sizes studied produce speedups greater than 60x on the NVIDIA Tesla C2075...13 2.3.3 CUDA API . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 2.3.4 CUDA and NVIDIA GPU Hardware...Theoretical Floating-Point Operations per Second for Intel CPUs and NVIDIA GPUs [3

On the design of a radix-10 online floating-point multiplier

NASA Astrophysics Data System (ADS)

McIlhenny, Robert D.; Ercegovac, Milos D.

2009-08-01

This paper describes an approach to design and implement a radix-10 online floating-point multiplier. An online approach is considered because it offers computational flexibility not available with conventional arithmetic. The design was coded in VHDL and compiled, synthesized, and mapped onto a Virtex 5 FPGA to measure cost in terms of LUTs (look-up-tables) as well as the cycle time and total latency. The routing delay which was not optimized is the major component in the cycle time. For a rough estimate of the cost/latency characteristics, our design was compared to a standard radix-2 floating-point multiplier of equivalent precision. The results demonstrate that even an unoptimized radix-10 online design is an attractive implementation alternative for FPGA floating-point multiplication.

40 CFR 426.50 - Applicability; description of the float glass manufacturing subcategory.

Code of Federal Regulations, 2011 CFR

2011-07-01

... float glass manufacturing subcategory. 426.50 Section 426.50 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS GLASS MANUFACTURING POINT SOURCE CATEGORY Float Glass Manufacturing Subcategory § 426.50 Applicability; description of the float glass...

40 CFR 426.50 - Applicability; description of the float glass manufacturing subcategory.

Code of Federal Regulations, 2010 CFR

2010-07-01

... float glass manufacturing subcategory. 426.50 Section 426.50 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS GLASS MANUFACTURING POINT SOURCE CATEGORY Float Glass Manufacturing Subcategory § 426.50 Applicability; description of the float glass...

Generating and executing programs for a floating point single instruction multiple data instruction set architecture

DOEpatents

Gschwind, Michael K

2013-04-16

Mechanisms for generating and executing programs for a floating point (FP) only single instruction multiple data (SIMD) instruction set architecture (ISA) are provided. A computer program product comprising a computer recordable medium having a computer readable program recorded thereon is provided. The computer readable program, when executed on a computing device, causes the computing device to receive one or more instructions and execute the one or more instructions using logic in an execution unit of the computing device. The logic implements a floating point (FP) only single instruction multiple data (SIMD) instruction set architecture (ISA), based on data stored in a vector register file of the computing device. The vector register file is configured to store both scalar and floating point values as vectors having a plurality of vector elements.

Design and FPGA Implementation of a Universal Chaotic Signal Generator Based on the Verilog HDL Fixed-Point Algorithm and State Machine Control

NASA Astrophysics Data System (ADS)

Qiu, Mo; Yu, Simin; Wen, Yuqiong; Lü, Jinhu; He, Jianbin; Lin, Zhuosheng

In this paper, a novel design methodology and its FPGA hardware implementation for a universal chaotic signal generator is proposed via the Verilog HDL fixed-point algorithm and state machine control. According to continuous-time or discrete-time chaotic equations, a Verilog HDL fixed-point algorithm and its corresponding digital system are first designed. In the FPGA hardware platform, each operation step of Verilog HDL fixed-point algorithm is then controlled by a state machine. The generality of this method is that, for any given chaotic equation, it can be decomposed into four basic operation procedures, i.e. nonlinear function calculation, iterative sequence operation, iterative values right shifting and ceiling, and chaotic iterative sequences output, each of which corresponds to only a state via state machine control. Compared with the Verilog HDL floating-point algorithm, the Verilog HDL fixed-point algorithm can save the FPGA hardware resources and improve the operation efficiency. FPGA-based hardware experimental results validate the feasibility and reliability of the proposed approach.

Parallel processor for real-time structural control

NASA Astrophysics Data System (ADS)

Tise, Bert L.

1993-07-01

A parallel processor that is optimized for real-time linear control has been developed. This modular system consists of A/D modules, D/A modules, and floating-point processor modules. The scalable processor uses up to 1,000 Motorola DSP96002 floating-point processors for a peak computational rate of 60 GFLOPS. Sampling rates up to 625 kHz are supported by this analog-in to analog-out controller. The high processing rate and parallel architecture make this processor suitable for computing state-space equations and other multiply/accumulate-intensive digital filters. Processor features include 14-bit conversion devices, low input-to-output latency, 240 Mbyte/s synchronous backplane bus, low-skew clock distribution circuit, VME connection to host computer, parallelizing code generator, and look- up-tables for actuator linearization. This processor was designed primarily for experiments in structural control. The A/D modules sample sensors mounted on the structure and the floating- point processor modules compute the outputs using the programmed control equations. The outputs are sent through the D/A module to the power amps used to drive the structure's actuators. The host computer is a Sun workstation. An OpenWindows-based control panel is provided to facilitate data transfer to and from the processor, as well as to control the operating mode of the processor. A diagnostic mode is provided to allow stimulation of the structure and acquisition of the structural response via sensor inputs.

Supercomputers Of The Future

NASA Technical Reports Server (NTRS)

Peterson, Victor L.; Kim, John; Holst, Terry L.; Deiwert, George S.; Cooper, David M.; Watson, Andrew B.; Bailey, F. Ron

1992-01-01

Report evaluates supercomputer needs of five key disciplines: turbulence physics, aerodynamics, aerothermodynamics, chemistry, and mathematical modeling of human vision. Predicts these fields will require computer speed greater than 10(Sup 18) floating-point operations per second (FLOP's) and memory capacity greater than 10(Sup 15) words. Also, new parallel computer architectures and new structured numerical methods will make necessary speed and capacity available.

UNIX as an environment for producing numerical software

NASA Technical Reports Server (NTRS)

Schryer, N. L.

1978-01-01

The UNIX operating system supports a number of software tools; a mathematical equation-setting language, a phototypesetting language, a FORTRAN preprocessor language, a text editor, and a command interpreter. The design, implementation, documentation, and maintenance of a portable FORTRAN test of the floating-point arithmetic unit of a computer is used to illustrate these tools at work.

Implicit-shifted Symmetric QR Singular Value Decomposition of 3x3 Matrices

DTIC Science & Technology

2016-04-01

Graph 33, 4, 138:1– 138:11. TREFETHEN, L. N., AND BAU III, D. 1997. Numerical linear algebra , vol. 50. Siam. XU, H., SIN, F., ZHU, Y., AND BARBIČ, J...matrices with minimal branching and elementary floating point operations. Tech. rep., University of Wisconsin- Madison. SAITO, S., ZHOU, Z.-Y., AND

Memory-efficient decoding of LDPC codes

NASA Technical Reports Server (NTRS)

Kwok-San Lee, Jason; Thorpe, Jeremy; Hawkins, Jon

2005-01-01

We present a low-complexity quantization scheme for the implementation of regular (3,6) LDPC codes. The quantization parameters are optimized to maximize the mutual information between the source and the quantized messages. Using this non-uniform quantized belief propagation algorithm, we have simulated that an optimized 3-bit quantizer operates with 0.2dB implementation loss relative to a floating point decoder, and an optimized 4-bit quantizer operates less than 0.1dB quantization loss.

Low Power Computing in Distributed Systems

DTIC Science & Technology

2006-04-01

performance applications. It has been adopted in embedded systems such as the Stargate from Crossbow [15] and the PASTA 4 0 0.1 0.2 0.3 0.4 (A) flo at...current consumption of the Stargate board is measured by an Agilent digital multimeter 34401A. The digital multimeter is connected with the PC for data...floating point operation vs. integer operation Power supply Digital multimeter Stargate board with Xscale processor 5 2.2 Library math function vs

40 CFR 63.1063 - Floating roof requirements.

Code of Federal Regulations, 2010 CFR

2010-07-01

... the point of refloating the floating roof shall be continuous and shall be performed as soon as... 40 Protection of Environment 10 2010-07-01 2010-07-01 false Floating roof requirements. 63.1063...) National Emission Standards for Storage Vessels (Tanks)-Control Level 2 § 63.1063 Floating roof...

50 CFR 86.13 - What is boating infrastructure?

Code of Federal Regulations, 2010 CFR

2010-10-01

..., currents, etc., that provide a temporary safe anchorage point or harbor of refuge during storms); (f) Floating docks and fixed piers; (g) Floating and fixed breakwaters; (h) Dinghy docks (floating or fixed...

40 CFR 65.45 - External floating roof converted into an internal floating roof.

Code of Federal Regulations, 2010 CFR

2010-07-01

... External floating roof converted into an internal floating roof. The owner or operator who elects to... 40 Protection of Environment 15 2010-07-01 2010-07-01 false External floating roof converted into an internal floating roof. 65.45 Section 65.45 Protection of Environment ENVIRONMENTAL PROTECTION...

Bit-parallel arithmetic in a massively-parallel associative processor

NASA Technical Reports Server (NTRS)

Scherson, Isaac D.; Kramer, David A.; Alleyne, Brian D.

1992-01-01

A simple but powerful new architecture based on a classical associative processor model is presented. Algorithms for performing the four basic arithmetic operations both for integer and floating point operands are described. For m-bit operands, the proposed architecture makes it possible to execute complex operations in O(m) cycles as opposed to O(m exp 2) for bit-serial machines. A word-parallel, bit-parallel, massively-parallel computing system can be constructed using this architecture with VLSI technology. The operation of this system is demonstrated for the fast Fourier transform and matrix multiplication.

Operateurs et engins de calcul en virgule flottante et leur application a la simulation en temps reel sur FPGA

NASA Astrophysics Data System (ADS)

Ould Bachir, Tarek

The real-time simulation of electrical networks gained a vivid industrial interest during recent years, motivated by the substantial development cost reduction that such a prototyping approach can offer. Real-time simulation allows the progressive inclusion of real hardware during its development, allowing its testing under realistic conditions. However, CPU-based simulations suffer from certain limitations such as the difficulty to reach time-steps of a few microsecond, an important challenge brought by modern power converters. Hence, industrial practitioners adopted the FPGA as a platform of choice for the implementation of calculation engines dedicated to the rapid real-time simulation of electrical networks. The reconfigurable technology broke the 5 kHz switching frequency barrier that is characteristic of CPU-based simulations. Moreover, FPGA-based real-time simulation offers many advantages, including the reduced latency of the simulation loop that is obtained thanks to a direct access to sensors and actuators. The fixed-point format is paradigmatic to FPGA-based digital signal processing. However, the format imposes a time penalty in the development process since the designer has to asses the required precision for all model variables. This fact brought an import research effort on the use of the floating-point format for the simulation of electrical networks. One of the main challenges in the use of the floating-point format are the long latencies required by the elementary arithmetic operators, particularly when an adder is used as an accumulator, an important building bloc for the implementation of integration rules such as the trapezoidal method. Hence, single-cycle floating-point accumulation forms the core of this research work. Our results help building such operators as accumulators, multiply-accumulators (MACs), and dot-product (DP) operators. These operators play a key role in the implementation of the proposed calculation engines. Therefore, this thesis contributes to the realm of FPGA-based real-time simulation in many ways. The research work proposes a new summation algorithm, which is a generalization of the so-called self-alignment technique. The new formulation is broader, simpler in its expression and hardware implementation. Our research helps formulating criteria to guarantee good accuracy, the criteria being established on a theoretical, as well as empirical basis. Moreover, the thesis offers a comprehensive analysis on the use of the redundant high radix carry-save (HRCS) format. The HRCS format is used to perform rapid additions of large mantissas. Two new HRCS operators are also proposed, namely an endomorphic adder and a HRCS to conventional converter. Once the mean to single-cycle accumulation is defined as a combination of the self-alignment technique and the HRCS format, the research focuses on the FPGA implementation of SIMD calculation engines using parallel floating-point MACs or DPs. The proposed operators are characterized by low latencies, allowing the engines to reach very low time-steps. The document finally discusses power electronic circuits modelling, and concludes with the presentation of a versatile calculation engine capable of simulating power converter with arbitrary topologies and up to 24 switches, while achieving time steps below 1 mus and allowing switching frequencies in the range of tens kilohertz. The latter realization has led to commercialization of a product by our industrial partner.

Measuring FLOPS Using Hardware Performance Counter Technologies on LC systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ahn, D H

2008-09-05

FLOPS (FLoating-point Operations Per Second) is a commonly used performance metric for scientific programs that rely heavily on floating-point (FP) calculations. The metric is based on the number of FP operations rather than instructions, thereby facilitating a fair comparison between different machines. A well-known use of this metric is the LINPACK benchmark that is used to generate the Top500 list. It measures how fast a computer solves a dense N by N system of linear equations Ax=b, which requires a known number of FP operations, and reports the result in millions of FP operations per second (MFLOPS). While running amore » benchmark with known FP workloads can provide insightful information about the efficiency of a machine's FP pipelines in relation to other machines, measuring FLOPS of an arbitrary scientific application in a platform-independent manner is nontrivial. The goal of this paper is twofold. First, we explore the FP microarchitectures of key processors that are underpinning the LC machines. Second, we present the hardware performance monitoring counter-based measurement techniques that a user can use to get the native FLOPS of his or her program, which are practical solutions readily available on LC platforms. By nature, however, these native FLOPS metrics are not directly comparable across different machines mainly because FP operations are not consistent across microarchitectures. Thus, the first goal of this paper represents the base reference by which a user can interpret the measured FLOPS more judiciously.« less

Universal Batch Steganalysis

DTIC Science & Technology

2014-06-30

steganalysis) in large-scale datasets such as might be obtained by monitoring a corporate network or social network. Identifying guilty actors...guilty’ user (of steganalysis) in large-scale datasets such as might be obtained by monitoring a corporate network or social network. Identifying guilty...floating point operations (1 TFLOPs) for a 1 megapixel image. We designed a new implementation using Compute Unified Device Architecture (CUDA) on NVIDIA

Special-purpose computer for holography HORN-2

NASA Astrophysics Data System (ADS)

Ito, Tomoyoshi; Eldeib, Hesham; Yoshida, Kenji; Takahashi, Shinya; Yabe, Takashi; Kunugi, Tomoaki

1996-01-01

We designed and built a special-purpose computer for holography, HORN-2 (HOlographic ReconstructioN). HORN-2 calculates light intensity at high speed of 0.3 Gflops per one board with single (32-bit floating point) precision. The cost of the board is 500 000 Japanese yen (5000 US dollar). We made three boards. Operating them in parallel, we get about 1 Gflops.

20-GFLOPS QR processor on a Xilinx Virtex-E FPGA

NASA Astrophysics Data System (ADS)

Walke, Richard L.; Smith, Robert W. M.; Lightbody, Gaye

2000-11-01

Adaptive beamforming can play an important role in sensor array systems in countering directional interference. In high-sample rate systems, such as radar and comms, the calculation of adaptive weights is a very computational task that requires highly parallel solutions. For systems where low power consumption and volume are important the only viable implementation is as an Application Specific Integrated Circuit (ASIC). However, the rapid advancement of Field Programmable Gate Array (FPGA) technology is enabling highly credible re-programmable solutions. In this paper we present the implementation of a scalable linear array processor for weight calculation using QR decomposition. We employ floating-point arithmetic with mantissa size optimized to the target application to minimize component size, and implement them as relationally placed macros (RPMs) on Xilinx Virtex FPGAs to achieve predictable dense layout and high-speed operation. We present results that show that 20GFLOPS of sustained computation on a single XCV3200E-8 Virtex-E FPGA is possible. We also describe the parameterized implementation of the floating-point operators and QR-processor, and the design methodology that enables us to rapidly generate complex FPGA implementations using the industry standard hardware description language VHDL.

Field programmable gate array-assigned complex-valued computation and its limits

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bernard-Schwarz, Maria, E-mail: maria.bernardschwarz@ni.com; Institute of Applied Physics, TU Wien, Wiedner Hauptstrasse 8, 1040 Wien; Zwick, Wolfgang

We discuss how leveraging Field Programmable Gate Array (FPGA) technology as part of a high performance computing platform reduces latency to meet the demanding real time constraints of a quantum optics simulation. Implementations of complex-valued operations using fixed point numeric on a Virtex-5 FPGA compare favorably to more conventional solutions on a central processing unit. Our investigation explores the performance of multiple fixed point options along with a traditional 64 bits floating point version. With this information, the lowest execution times can be estimated. Relative error is examined to ensure simulation accuracy is maintained.

A High-Level Formalization of Floating-Point Number in PVS

NASA Technical Reports Server (NTRS)

Boldo, Sylvie; Munoz, Cesar

2006-01-01

We develop a formalization of floating-point numbers in PVS based on a well-known formalization in Coq. We first describe the definitions of all the needed notions, e.g., floating-point number, format, rounding modes, etc.; then, we present an application to polynomial evaluation for elementary function evaluation. The application already existed in Coq, but our formalization shows a clear improvement in the quality of the result due to the automation provided by PVS. We finally integrate our formalization into a PVS hardware-level formalization of the IEEE-854 standard previously developed at NASA.

33 CFR 147.815 - ExxonMobil Hoover Floating OCS Facility safety zone.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false ExxonMobil Hoover Floating OCS... Floating OCS Facility safety zone. (a) Description. The ExxonMobil Hoover Floating OCS Facility, Alaminos... (1640.4 feet) from each point on the structure's outer edge is a safety zone. (b) Regulation. No vessel...

[Study on the experimental application of floating-reference method to noninvasive blood glucose sensing].

PubMed

Yu, Hui; Qi, Dan; Li, Heng-da; Xu, Ke-xin; Yuan, Wei-jie

2012-03-01

Weak signal, low instrument signal-to-noise ratio, continuous variation of human physiological environment and the interferences from other components in blood make it difficult to extract the blood glucose information from near infrared spectrum in noninvasive blood glucose measurement. The floating-reference method, which analyses the effect of glucose concentration variation on absorption coefficient and scattering coefficient, gets spectrum at the reference point and the measurement point where the light intensity variations from absorption and scattering are counteractive and biggest respectively. By using the spectrum from reference point as reference, floating-reference method can reduce the interferences from variation of physiological environment and experiment circumstance. In the present paper, the effectiveness of floating-reference method working on improving prediction precision and stability was assessed through application experiments. The comparison was made between models whose data were processed with and without floating-reference method. The results showed that the root mean square error of prediction (RMSEP) decreased by 34.7% maximally. The floating-reference method could reduce the influences of changes of samples' state, instrument noises and drift, and improve the models' prediction precision and stability effectively.

Parallel processor for real-time structural control

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tise, B.L.

1992-01-01

A parallel processor that is optimized for real-time linear control has been developed. This modular system consists of A/D modules, D/A modules, and floating-point processor modules. The scalable processor uses up to 1,000 Motorola DSP96002 floating-point processors for a peak computational rate of 60 GFLOPS. Sampling rates up to 625 kHz are supported by this analog-in to analog-out controller. The high processing rate and parallel architecture make this processor suitable for computing state-space equations and other multiply/accumulate-intensive digital filters. Processor features include 14-bit conversion devices, low input-output latency, 240 Mbyte/s synchronous backplane bus, low-skew clock distribution circuit, VME connection tomore » host computer, parallelizing code generator, and look-up-tables for actuator linearization. This processor was designed primarily for experiments in structural control. The A/D modules sample sensors mounted on the structure and the floating-point processor modules compute the outputs using the programmed control equations. The outputs are sent through the D/A module to the power amps used to drive the structure's actuators. The host computer is a Sun workstation. An Open Windows-based control panel is provided to facilitate data transfer to and from the processor, as well as to control the operating mode of the processor. A diagnostic mode is provided to allow stimulation of the structure and acquisition of the structural response via sensor inputs.« less

Unified random access memory (URAM) by integration of a nanocrystal floating gate for nonvolatile memory and a partially depleted floating body for capacitorless 1T-DRAM

NASA Astrophysics Data System (ADS)

Ryu, Seong-Wan; Han, Jin-Woo; Kim, Chung-Jin; Kim, Sungho; Choi, Yang-Kyu

2009-03-01

This paper describes a unified memory (URAM) that utilizes a nanocrystal SOI MOSFET for multi-functional applications of both nonvolatile memory (NVM) and capacitorless 1T-DRAM. By using a discrete storage node (Ag nanocrystal) as the floating gate of the NVM, high defect immunity and 2-bit/cell operation were achieved. The embedded nanocrystal NVM also showed 1T-DRAM operation (program/erase time = 100 ns) characteristics, which were realized by storing holes in the floating body of the SOI MOSFET, without requiring an external capacitor. Three-bit/cell operation was accomplished for different applications - 2-bits for nonvolatility and 1-bit for fast operation.

Real object-based 360-degree integral-floating display using multiple depth camera

NASA Astrophysics Data System (ADS)

Erdenebat, Munkh-Uchral; Dashdavaa, Erkhembaatar; Kwon, Ki-Chul; Wu, Hui-Ying; Yoo, Kwan-Hee; Kim, Young-Seok; Kim, Nam

2015-03-01

A novel 360-degree integral-floating display based on the real object is proposed. The general procedure of the display system is similar with conventional 360-degree integral-floating displays. Unlike previously presented 360-degree displays, the proposed system displays the 3D image generated from the real object in 360-degree viewing zone. In order to display real object in 360-degree viewing zone, multiple depth camera have been utilized to acquire the depth information around the object. Then, the 3D point cloud representations of the real object are reconstructed according to the acquired depth information. By using a special point cloud registration method, the multiple virtual 3D point cloud representations captured by each depth camera are combined as single synthetic 3D point cloud model, and the elemental image arrays are generated for the newly synthesized 3D point cloud model from the given anamorphic optic system's angular step. The theory has been verified experimentally, and it shows that the proposed 360-degree integral-floating display can be an excellent way to display real object in the 360-degree viewing zone.

40 CFR 60.693-2 - Alternative standards for oil-water separators.

Code of Federal Regulations, 2010 CFR

2010-07-01

...-water separators. (a) An owner or operator may elect to construct and operate a floating roof on an oil... requirements of this subpart which meets the following specifications. (1) Each floating roof shall be equipped... the liquid between the wall of the separator and the floating roof. A mechanical shoe seal means a...

40 CFR 264.1085 - Standards: Surface impoundments.

Code of Federal Regulations, 2010 CFR

2010-07-01

... the surface impoundment by installing and operating either of the following: (1) A floating membrane... from a surface impoundment using a floating membrane cover shall meet the requirements specified in... floating membrane cover designed to meet the following specifications: (i) The floating membrane cover...

Percutaneous nephrostomy for symptomatic hypermobile kidney: a single centre experience.

PubMed

Starownik, Radosław; Golabek, Tomasz; Bar, Krzysztof; Muc, Kamil; Płaza, Paweł; Chlosta, Piotr

2014-12-01

Symptomatic hypermobile kidney is treated with nephropexy, a surgical procedure through which the floating kidney is fixed to the retroperitoneum. Although both open and endoscopic procedures have a high success rate, they can be associated with risk of complications, relatively long hospital stay and high cost. We describe our percutaneous technique for fixing a hypermobile kidney and evaluate the efficacy of the percutaneous nephrostomy insertion in management of symptomatic nephroptosis. Between January 2005 and December 2011, 11 patients diagnosed with a symptomatic right nephroptosis of at least 1 year duration were treated with a single point percutaneous nephrostomy technique. All data were retrieved from patients' medical records and then retrospectively analysed. Nephropexy through a single point percutaneous nephrostomy technique was successfully accomplished in 11 women. The mean operative time was 20 min. The intraoperative estimated blood loss was minimal in all cases. No major or minor intraoperative complications were noted. The average postoperative hospital stay was 2 days. Women returned to their usual activities 14 days following the surgery. Nine women had complete resolution of their pain, and 2 patients continued to complain of discomfort in their lumbar area. One patient was re-operated upon with satisfactory subjective and objective outcomes achieved. One patient refused re-operation. Percutaneous nephropexy is simple, inexpensive and effective for treatment of symptomatic hypermobile kidney. It remains a valuable alternative to open, laparoscopic, and robotic methods for fixing a floating kidney.

ZFP compression plugin (filter) for HDF5

DOE Office of Scientific and Technical Information (OSTI.GOV)

Miller, Mark C.

H5Z-ZFP is a compression plugin (filter) for the HDF5 library based upon the ZFP-0.5.0 compression library. It supports 4- or 8-byte integer or floating point HDF5 datasets of any dimension but partitioned in 1, 2, or 3 dimensional chunks. It supports ZFP's four fundamental modes of operation; rate, precision, accuracy or expert. It is a lossy compression plugin.

U. S. Naval Forces, Vietnam Monthly Historical Supplement for September 1969

DTIC Science & Technology

1969-12-01

A. SEAI.O)RDS - lISEP B. 5A,•f lORDS - 22 SEP,.". I *A "’\\4 5.: SCALl , CA MAU POINT _ __0 NAUTICAL MILES CG 41 POULO77.BASE 08I -I ".-il - v-CC...Cambodia. (See discussion of Border Interdiction Capaign within Operation SIA LOIDS Suwzary and discussion of SEA FLOAT in Coastal Surreillanoe 4 Tore

A Real-Time Marker-Based Visual Sensor Based on a FPGA and a Soft Core Processor

PubMed Central

Tayara, Hilal; Ham, Woonchul; Chong, Kil To

2016-01-01

This paper introduces a real-time marker-based visual sensor architecture for mobile robot localization and navigation. A hardware acceleration architecture for post video processing system was implemented on a field-programmable gate array (FPGA). The pose calculation algorithm was implemented in a System on Chip (SoC) with an Altera Nios II soft-core processor. For every frame, single pass image segmentation and Feature Accelerated Segment Test (FAST) corner detection were used for extracting the predefined markers with known geometries in FPGA. Coplanar PosIT algorithm was implemented on the Nios II soft-core processor supplied with floating point hardware for accelerating floating point operations. Trigonometric functions have been approximated using Taylor series and cubic approximation using Lagrange polynomials. Inverse square root method has been implemented for approximating square root computations. Real time results have been achieved and pixel streams have been processed on the fly without any need to buffer the input frame for further implementation. PMID:27983714

A Real-Time Marker-Based Visual Sensor Based on a FPGA and a Soft Core Processor.

PubMed

Tayara, Hilal; Ham, Woonchul; Chong, Kil To

2016-12-15

This paper introduces a real-time marker-based visual sensor architecture for mobile robot localization and navigation. A hardware acceleration architecture for post video processing system was implemented on a field-programmable gate array (FPGA). The pose calculation algorithm was implemented in a System on Chip (SoC) with an Altera Nios II soft-core processor. For every frame, single pass image segmentation and Feature Accelerated Segment Test (FAST) corner detection were used for extracting the predefined markers with known geometries in FPGA. Coplanar PosIT algorithm was implemented on the Nios II soft-core processor supplied with floating point hardware for accelerating floating point operations. Trigonometric functions have been approximated using Taylor series and cubic approximation using Lagrange polynomials. Inverse square root method has been implemented for approximating square root computations. Real time results have been achieved and pixel streams have been processed on the fly without any need to buffer the input frame for further implementation.

Non-uniqueness of the point of application of the buoyancy force

NASA Astrophysics Data System (ADS)

Kliava, Janis; Mégel, Jacques

2010-07-01

Even though the buoyancy force (also known as the Archimedes force) has always been an important topic of academic studies in physics, its point of application has not been explicitly identified yet. We present a quantitative approach to this problem based on the concept of the hydrostatic energy, considered here for a general shape of the cross-section of a floating body and for an arbitrary angle of heel. We show that the location of the point of application of the buoyancy force essentially depends (i) on the type of motion experienced by the floating body and (ii) on the definition of this point. In a rolling/pitching motion, considerations involving the rotational moment lead to a particular dynamical point of application of the buoyancy force, and for some simple shapes of the floating body this point coincides with the well-known metacentre. On the other hand, from the work-energy relation it follows that in the rolling/pitching motion the energetical point of application of this force is rigidly connected to the centre of buoyancy; in contrast, in a vertical translation this point is rigidly connected to the centre of gravity of the body. Finally, we consider the location of the characteristic points of the floating bodies for some particular shapes of immersed cross-sections. The paper is intended for higher education level physics teachers and students.

Verification of IEEE Compliant Subtractive Division Algorithms

NASA Technical Reports Server (NTRS)

Miner, Paul S.; Leathrum, James F., Jr.

1996-01-01

A parameterized definition of subtractive floating point division algorithms is presented and verified using PVS. The general algorithm is proven to satisfy a formal definition of an IEEE standard for floating point arithmetic. The utility of the general specification is illustrated using a number of different instances of the general algorithm.

VLSI Design Techniques for Floating-Point Computation

DTIC Science & Technology

1988-11-18

J. C. Gibson, The Gibson Mix, IBM Systems Development Division Tech. Report(June 1970). [Heni83] A. Heninger, The Zilog Z8070 Floating-Point...Broadcast Oock Gen. ’ itp Divide Module Module byN Module Oock Communication l I T Oock Communication Bus Figure 7.2. Clock Distribution between

40 CFR 65.44 - External floating roof (EFR).

Code of Federal Regulations, 2010 CFR

2010-07-01

... design requirements. The owner or operator who elects to control storage vessel regulated material emissions by using an external floating roof shall comply with the design requirements listed in paragraphs (a)(1) through (3) of this section. (1) The external floating roof shall be designed to float on the...

40 CFR 65.44 - External floating roof (EFR).

Code of Federal Regulations, 2011 CFR

2011-07-01

... design requirements. The owner or operator who elects to control storage vessel regulated material emissions by using an external floating roof shall comply with the design requirements listed in paragraphs (a)(1) through (3) of this section. (1) The external floating roof shall be designed to float on the...

A semi-floating gate memory based on van der Waals heterostructures for quasi-non-volatile applications

NASA Astrophysics Data System (ADS)

Liu, Chunsen; Yan, Xiao; Song, Xiongfei; Ding, Shijin; Zhang, David Wei; Zhou, Peng

2018-05-01

As conventional circuits based on field-effect transistors are approaching their physical limits due to quantum phenomena, semi-floating gate transistors have emerged as an alternative ultrafast and silicon-compatible technology. Here, we show a quasi-non-volatile memory featuring a semi-floating gate architecture with band-engineered van der Waals heterostructures. This two-dimensional semi-floating gate memory demonstrates 156 times longer refresh time with respect to that of dynamic random access memory and ultrahigh-speed writing operations on nanosecond timescales. The semi-floating gate architecture greatly enhances the writing operation performance and is approximately 106 times faster than other memories based on two-dimensional materials. The demonstrated characteristics suggest that the quasi-non-volatile memory has the potential to bridge the gap between volatile and non-volatile memory technologies and decrease the power consumption required for frequent refresh operations, enabling a high-speed and low-power random access memory.

Efficient Boundary Extraction of BSP Solids Based on Clipping Operations.

PubMed

Wang, Charlie C L; Manocha, Dinesh

2013-01-01

We present an efficient algorithm to extract the manifold surface that approximates the boundary of a solid represented by a Binary Space Partition (BSP) tree. Our polygonization algorithm repeatedly performs clipping operations on volumetric cells that correspond to a spatial convex partition and computes the boundary by traversing the connected cells. We use point-based representations along with finite-precision arithmetic to improve the efficiency and generate the B-rep approximation of a BSP solid. The core of our polygonization method is a novel clipping algorithm that uses a set of logical operations to make it resistant to degeneracies resulting from limited precision of floating-point arithmetic. The overall BSP to B-rep conversion algorithm can accurately generate boundaries with sharp and small features, and is faster than prior methods. At the end of this paper, we use this algorithm for a few geometric processing applications including Boolean operations, model repair, and mesh reconstruction.

Fast orthogonal transforms and generation of Brownian paths

PubMed Central

Leobacher, Gunther

2012-01-01

We present a number of fast constructions of discrete Brownian paths that can be used as alternatives to principal component analysis and Brownian bridge for stratified Monte Carlo and quasi-Monte Carlo. By fast we mean that a path of length n can be generated in O(nlog(n)) floating point operations. We highlight some of the connections between the different constructions and we provide some numerical examples. PMID:23471545

Large space structures control algorithm characterization

NASA Technical Reports Server (NTRS)

Fogel, E.

1983-01-01

Feedback control algorithms are developed for sensor/actuator pairs on large space systems. These algorithms have been sized in terms of (1) floating point operation (FLOP) demands; (2) storage for variables; and (3) input/output data flow. FLOP sizing (per control cycle) was done as a function of the number of control states and the number of sensor/actuator pairs. Storage for variables and I/O sizing was done for specific structure examples.

Solving Navier-Stokes equations on a massively parallel processor; The 1 GFLOP performance

DOE Office of Scientific and Technical Information (OSTI.GOV)

Saati, A.; Biringen, S.; Farhat, C.

This paper reports on experience in solving large-scale fluid dynamics problems on the Connection Machine model CM-2. The authors have implemented a parallel version of the MacCormack scheme for the solution of the Navier-Stokes equations. By using triad floating point operations and reducing the number of interprocessor communications, they have achieved a sustained performance rate of 1.42 GFLOPS.

Implementing direct, spatially isolated problems on transputer networks

NASA Technical Reports Server (NTRS)

Ellis, Graham K.

1988-01-01

Parametric studies were performed on transputer networks of up to 40 processors to determine how to implement and maximize the performance of the solution of problems where no processor-to-processor data transfer is required for the problem solution (spatially isolated). Two types of problems are investigated a computationally intensive problem where the solution required the transmission of 160 bytes of data through the parallel network, and a communication intensive example that required the transmission of 3 Mbytes of data through the network. This data consists of solutions being sent back to the host processor and not intermediate results for another processor to work on. Studies were performed on both integer and floating-point transputers. The latter features an on-chip floating-point math unit and offers approximately an order of magnitude performance increase over the integer transputer on real valued computations. The results indicate that a minimum amount of work is required on each node per communication to achieve high network speedups (efficiencies). The floating-point processor requires approximately an order of magnitude more work per communication than the integer processor because of the floating-point unit's increased computing capacity.

Numerical model of a single nanocrystal devoted to the study of disordered nanocrystal floating gates of new flash memories

NASA Astrophysics Data System (ADS)

Leroy, Yann; Armeanu, Dumitru; Cordan, Anne-Sophie

2011-05-01

The improvement of our model concerning a single nanocrystal that belongs to a nanocrystal floating gate of a flash memory is presented. In order to extend the gate voltage range applicability of the model, the 3D continuum of states of either metallic or semiconducting electrodes is discretized into 2D subbands. Such an approach gives precise information about the mechanisms behind the charging or release processes of the nanocrystal. Then, the self-energy and screening effects of an electron within the nanocrystal are evaluated and introduced in the model. This enables a better determination of the operating point of the nanocrystal memory. The impact of those improvements on the charging or release time of the nanocrystal is discussed.

46 CFR 131.870 - Life floats and buoyant apparatus.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 4 2012-10-01 2012-10-01 false Life floats and buoyant apparatus. 131.870 Section 131... OPERATIONS Markings for Fire Equipment and Emergency Equipment § 131.870 Life floats and buoyant apparatus. (a) The name of the vessel must be plainly marked or painted on each life float or buoyant apparatus...

46 CFR 131.870 - Life floats and buoyant apparatus.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 4 2013-10-01 2013-10-01 false Life floats and buoyant apparatus. 131.870 Section 131... OPERATIONS Markings for Fire Equipment and Emergency Equipment § 131.870 Life floats and buoyant apparatus. (a) The name of the vessel must be plainly marked or painted on each life float or buoyant apparatus...

46 CFR 131.870 - Life floats and buoyant apparatus.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 4 2014-10-01 2014-10-01 false Life floats and buoyant apparatus. 131.870 Section 131... OPERATIONS Markings for Fire Equipment and Emergency Equipment § 131.870 Life floats and buoyant apparatus. (a) The name of the vessel must be plainly marked or painted on each life float or buoyant apparatus...

46 CFR 131.870 - Life floats and buoyant apparatus.

Code of Federal Regulations, 2011 CFR

2011-10-01

... OPERATIONS Markings for Fire Equipment and Emergency Equipment § 131.870 Life floats and buoyant apparatus. (a) The name of the vessel must be plainly marked or painted on each life float or buoyant apparatus... 46 Shipping 4 2011-10-01 2011-10-01 false Life floats and buoyant apparatus. 131.870 Section 131...

46 CFR 131.870 - Life floats and buoyant apparatus.

Code of Federal Regulations, 2010 CFR

2010-10-01

... OPERATIONS Markings for Fire Equipment and Emergency Equipment § 131.870 Life floats and buoyant apparatus. (a) The name of the vessel must be plainly marked or painted on each life float or buoyant apparatus... 46 Shipping 4 2010-10-01 2010-10-01 false Life floats and buoyant apparatus. 131.870 Section 131...

CT image reconstruction with half precision floating-point values.

PubMed

Maaß, Clemens; Baer, Matthias; Kachelrieß, Marc

2011-07-01

Analytic CT image reconstruction is a computationally demanding task. Currently, the even more demanding iterative reconstruction algorithms find their way into clinical routine because their image quality is superior to analytic image reconstruction. The authors thoroughly analyze a so far unconsidered but valuable tool of tomorrow's reconstruction hardware (CPU and GPU) that allows implementing the forward projection and backprojection steps, which are the computationally most demanding parts of any reconstruction algorithm, much more efficiently. Instead of the standard 32 bit floating-point values (float), a recently standardized floating-point value with 16 bit (half) is adopted for data representation in image domain and in rawdata domain. The reduction in the total data amount reduces the traffic on the memory bus, which is the bottleneck of today's high-performance algorithms, by 50%. In CT simulations and CT measurements, float reconstructions (gold standard) and half reconstructions are visually compared via difference images and by quantitative image quality evaluation. This is done for analytical reconstruction (filtered backprojection) and iterative reconstruction (ordered subset SART). The magnitude of quantization noise, which is caused by a reduction in the data precision of both rawdata and image data during image reconstruction, is negligible. This is clearly shown for filtered backprojection and iterative ordered subset SART reconstruction. In filtered backprojection, the implementation of the backprojection should be optimized for low data precision if the image data are represented in half format. In ordered subset SART image reconstruction, no adaptations are necessary and the convergence speed remains unchanged. Half precision floating-point values allow to speed up CT image reconstruction without compromising image quality.

Northern Arabian Sea Circulation - Autonomous Research: Optimal Planning Systems (NASCar-OPS)

DTIC Science & Technology

2015-09-30

vehicles ( gliders , drifters, floats, and/or wave- gliders ) - Provide guidance for persistent optimal sampling, including for long-duration observation...headings and relative operating speeds will be provided to the operational fleets of instruments and vehicles (e.g. gliders , drifters, floats or wave... gliders ). We plan to use models specific to vehicle types (floats, wave- gliders , etc.). We also plan to further parallelize and optimize our codes

An embedded controller for a 7-degree of freedom prosthetic arm.

PubMed

Tenore, Francesco; Armiger, Robert S; Vogelstein, R Jacob; Wenstrand, Douglas S; Harshbarger, Stuart D; Englehart, Kevin

2008-01-01

We present results from an embedded real-time hardware system capable of decoding surface myoelectric signals (sMES) to control a seven degree of freedom upper limb prosthesis. This is one of the first hardware implementations of sMES decoding algorithms and the most advanced controller to-date. We compare decoding results from the device to simulation results from a real-time PC-based operating system. Performance of both systems is shown to be similar, with decoding accuracy greater than 90% for the floating point software simulation and 80% for fixed point hardware and software implementations.

Dataflow-Based Implementation of Layered Sensing Applications on High-Performance Embedded Processors

DTIC Science & Technology

2013-03-01

time (milliseconds) GFlops Comparison to GPU peak performance (%) Cascade Gaussian Filtering 13 45.19 6.3 Difference of Gaussian 0.512 152...values for the GPU-targeted actor implementations in terms of Giga Floating Point Operations Per Second ( GFLOPS ). Our GFLOPS calculation for an actor...kernels. The results for GFLOPS are provided in Table . The actors were implemented on an NVIDIA GTX260 GPU, which provides 715 GFLOPS as peak

Desirable floating-point arithmetic and elementary functions for numerical computation

NASA Technical Reports Server (NTRS)

Hull, T. E.

1978-01-01

The topics considered are: (1) the base of the number system, (2) precision control, (3) number representation, (4) arithmetic operations, (5) other basic operations, (6) elementary functions, and (7) exception handling. The possibility of doing without fixed-point arithmetic is also mentioned. The specifications are intended to be entirely at the level of a programming language such as FORTRAN. The emphasis is on convenience and simplicity from the user's point of view. Conforming to such specifications would have obvious beneficial implications for the portability of numerical software, and for proving programs correct, as well as attempting to provide facilities which are most suitable for the user. The specifications are not complete in every detail, but it is intended that they be complete in spirit - some further details, especially syntatic details, would have to be provided, but the proposals are otherwise relatively complete.

Rational Arithmetic in Floating-Point.

DTIC Science & Technology

1986-09-01

RD-RI75 190 RATIONAL ARITHMETIC IN FLOTING-POINT(U) CALIFORNIA~UNIY BERKELEY CENTER FOR PURE AND APPLIED MATHEMATICS USI FE N KAHAN SEP 86 PRM-343...8217 ," .’,.-.’ .- " .- . ,,,.". ".. .. ". CENTER FOR PURE AND APPLIED MATHEMATICS UNIVERSITY OF CALIFORNIA, BERKELEY PAf4343 0l RATIONAL ARITHMIETIC IN FLOATING-POINT W. KAHAN SETMER18 SEPTEMBE...delicate balance between, on the one hand, the simplicity and aesthetic appeal of the specifications and, on the other hand, the complexity and

Ambipolar organic thin-film transistor-based nano-floating-gate nonvolatile memory

NASA Astrophysics Data System (ADS)

Han, Jinhua; Wang, Wei; Ying, Jun; Xie, Wenfa

2014-01-01

An ambipolar organic thin-film transistor-based nano-floating-gate nonvolatile memory was demonstrated, with discrete distributed gold nanoparticles, tetratetracontane (TTC), pentacene as the floating-gate layer, tunneling layer, and active layer, respectively. The electron traps at the TTC/pentacene interface were significantly suppressed, which resulted in an ambipolar operation in present memory. As both electrons and holes were supplied in the channel and trapped in the floating-gate by programming/erasing operations, respectively, i.e., one type of charge carriers was used to overwrite the other, trapped, one, a large memory window, extending on both sides of the initial threshold voltage, was realized.

33 CFR 165.704 - Safety Zone; Tampa Bay, Florida.

Code of Federal Regulations, 2010 CFR

2010-07-01

..., Florida. (a) A floating safety zone is established consisting of an area 1000 yards fore and aft of a... ending at Gadsden Point Cut Lighted Buoys “3” and “4”. The safety zone starts again at Gadsden Point Cut... the marked channel at Tampa Bay Cut “K” buoy “11K” enroute to Rattlesnake, Tampa, FL, the floating...

Learning to assign binary weights to binary descriptor

NASA Astrophysics Data System (ADS)

Huang, Zhoudi; Wei, Zhenzhong; Zhang, Guangjun

2016-10-01

Constructing robust binary local feature descriptors are receiving increasing interest due to their binary nature, which can enable fast processing while requiring significantly less memory than their floating-point competitors. To bridge the performance gap between the binary and floating-point descriptors without increasing the computational cost of computing and matching, optimal binary weights are learning to assign to binary descriptor for considering each bit might contribute differently to the distinctiveness and robustness. Technically, a large-scale regularized optimization method is applied to learn float weights for each bit of the binary descriptor. Furthermore, binary approximation for the float weights is performed by utilizing an efficient alternatively greedy strategy, which can significantly improve the discriminative power while preserve fast matching advantage. Extensive experimental results on two challenging datasets (Brown dataset and Oxford dataset) demonstrate the effectiveness and efficiency of the proposed method.

AN ADA LINEAR ALGEBRA PACKAGE MODELED AFTER HAL/S

NASA Technical Reports Server (NTRS)

Klumpp, A. R.

1994-01-01

This package extends the Ada programming language to include linear algebra capabilities similar to those of the HAL/S programming language. The package is designed for avionics applications such as Space Station flight software. In addition to the HAL/S built-in functions, the package incorporates the quaternion functions used in the Shuttle and Galileo projects, and routines from LINPAK that solve systems of equations involving general square matrices. Language conventions in this package follow those of HAL/S to the maximum extent practical and minimize the effort required for writing new avionics software and translating existent software into Ada. Valid numeric types in this package include scalar, vector, matrix, and quaternion declarations. (Quaternions are fourcomponent vectors used in representing motion between two coordinate frames). Single precision and double precision floating point arithmetic is available in addition to the standard double precision integer manipulation. Infix operators are used instead of function calls to define dot products, cross products, quaternion products, and mixed scalar-vector, scalar-matrix, and vector-matrix products. The package contains two generic programs: one for floating point, and one for integer. The actual component type is passed as a formal parameter to the generic linear algebra package. The procedures for solving systems of linear equations defined by general matrices include GEFA, GECO, GESL, and GIDI. The HAL/S functions include ABVAL, UNIT, TRACE, DET, INVERSE, TRANSPOSE, GET, PUT, FETCH, PLACE, and IDENTITY. This package is written in Ada (Version 1.2) for batch execution and is machine independent. The linear algebra software depends on nothing outside the Ada language except for a call to a square root function for floating point scalars (such as SQRT in the DEC VAX MATHLIB library). This program was developed in 1989, and is a copyrighted work with all copyright vested in NASA.

Applications Performance on NAS Intel Paragon XP/S - 15#

NASA Technical Reports Server (NTRS)

Saini, Subhash; Simon, Horst D.; Copper, D. M. (Technical Monitor)

1994-01-01

The Numerical Aerodynamic Simulation (NAS) Systems Division received an Intel Touchstone Sigma prototype model Paragon XP/S- 15 in February, 1993. The i860 XP microprocessor with an integrated floating point unit and operating in dual -instruction mode gives peak performance of 75 million floating point operations (NIFLOPS) per second for 64 bit floating point arithmetic. It is used in the Paragon XP/S-15 which has been installed at NAS, NASA Ames Research Center. The NAS Paragon has 208 nodes and its peak performance is 15.6 GFLOPS. Here, we will report on early experience using the Paragon XP/S- 15. We have tested its performance using both kernels and applications of interest to NAS. We have measured the performance of BLAS 1, 2 and 3 both assembly-coded and Fortran coded on NAS Paragon XP/S- 15. Furthermore, we have investigated the performance of a single node one-dimensional FFT, a distributed two-dimensional FFT and a distributed three-dimensional FFT Finally, we measured the performance of NAS Parallel Benchmarks (NPB) on the Paragon and compare it with the performance obtained on other highly parallel machines, such as CM-5, CRAY T3D, IBM SP I, etc. In particular, we investigated the following issues, which can strongly affect the performance of the Paragon: a. Impact of the operating system: Intel currently uses as a default an operating system OSF/1 AD from the Open Software Foundation. The paging of Open Software Foundation (OSF) server at 22 MB to make more memory available for the application degrades the performance. We found that when the limit of 26 NIB per node out of 32 MB available is reached, the application is paged out of main memory using virtual memory. When the application starts paging, the performance is considerably reduced. We found that dynamic memory allocation can help applications performance under certain circumstances. b. Impact of data cache on the i860/XP: We measured the performance of the BLAS both assembly coded and Fortran coded. We found that the measured performance of assembly-coded BLAS is much less than what memory bandwidth limitation would predict. The influence of data cache on different sizes of vectors is also investigated using one-dimensional FFTs. c. Impact of processor layout: There are several different ways processors can be laid out within the two-dimensional grid of processors on the Paragon. We have used the FFT example to investigate performance differences based on processors layout.

Modeling of submarine melting in Petermann Fjord, Northwestern Greenland using an ocean general circulation model

NASA Astrophysics Data System (ADS)

Cai, C.; Rignot, E. J.; Xu, Y.; An, L.

2013-12-01

Basal melting of the floating tongue of Petermann Glacier, in northwestern Greenland is by far the largest process of mass ablation. Melting of the floating tongue is controlled by the buoyancy of the melt water plume, the pressure-dependence of the melting point of sea ice, and the mixing of warm subsurface water with fresh buoyant subglacial discharge. In prior simulations of this melting process, the role of subglacial discharge has been neglected because in similar configurations (floating ice shelves) in the Antarctic, surface runoff is negligible; this is however not true in Greenland. Here, we use the Mass Institute of Technology general circulation model (MITgcm) at a high spatial resolution (10 m x 10 m) to simulate the melting process of the ice shelf in 2-D. the model is constrained by ice shelf bathymetry and ice thickness from NASA Operation IceBridge, ocean temperature/salinity data from Johnson et al. (2011), and subglacial discharge estimated from output products of the Regional Atmospheric Climate Model (RACMO). We compare the results obtained in winter (no runoff) with summer, and the sensitivity of the results to thermal forcing from the ocean, and to the magnitude of subglacial runoff. We conclude on the impact of the ocean and surface melting on the melting regime of the floating ice tongue of Petermann. This work is performed under a contract with NASA Cryosphere Program.

Characterization of a medium-sized washer-gun for an axisymmetric mirror

NASA Astrophysics Data System (ADS)

Yi, Hongshen; Liu, Ming; Shi, Peiyun; Yang, Zhida; Zhu, Guanghui; Lu, Quanming; Sun, Xuan

2018-04-01

A new medium-sized washer gun is developed for a plasma start-up in a fully axisymmetric mirror. The gun is positioned at the east end of the Keda Mirror with AXisymmetricity facility and operated in the pulsed mode with an arc discharging time of 1.2 ms and a typical arc current of 8.5 kA with 1.5 kV discharge voltage. To optimize the operation, a systematic scan of the neutral pressure, the arc voltage, the bias voltage on a mesh grid 6 cm in front of the gun and an end electrode located on the west end of mirror, and the mirror ratio was performed. The streaming plasma was measured with triple probes in the three mirror cells and a diamagnetic loop in the central cell. Floating potential measurements suggest that the plasma could be divided into streaming and mirror-confined plasmas. The floating potential for the streaming plasma is negative, with an electric field pointing inwards. The mirror-confined plasma has a typical lifetime of 0.5 ms.

Characterization of a medium-sized washer-gun for an axisymmetric mirror.

PubMed

Yi, Hongshen; Liu, Ming; Shi, Peiyun; Yang, Zhida; Zhu, Guanghui; Lu, Quanming; Sun, Xuan

2018-04-01

A new medium-sized washer gun is developed for a plasma start-up in a fully axisymmetric mirror. The gun is positioned at the east end of the Keda Mirror with AXisymmetricity facility and operated in the pulsed mode with an arc discharging time of 1.2 ms and a typical arc current of 8.5 kA with 1.5 kV discharge voltage. To optimize the operation, a systematic scan of the neutral pressure, the arc voltage, the bias voltage on a mesh grid 6 cm in front of the gun and an end electrode located on the west end of mirror, and the mirror ratio was performed. The streaming plasma was measured with triple probes in the three mirror cells and a diamagnetic loop in the central cell. Floating potential measurements suggest that the plasma could be divided into streaming and mirror-confined plasmas. The floating potential for the streaming plasma is negative, with an electric field pointing inwards. The mirror-confined plasma has a typical lifetime of 0.5 ms.

40 CFR 264.1084 - Standards: Tanks.

Code of Federal Regulations, 2010 CFR

2010-07-01

... internal floating roof in accordance with the requirements specified in paragraph (e) of this section; (2) A tank equipped with an external floating roof in accordance with the requirements specified in... operator who controls air pollutant emissions from a tank using a fixed roof with an internal floating roof...

Feasibility study, software design, layout and simulation of a two-dimensional Fast Fourier Transform machine for use in optical array interferometry

NASA Technical Reports Server (NTRS)

Boriakoff, Valentin

1994-01-01

The goal of this project was the feasibility study of a particular architecture of a digital signal processing machine operating in real time which could do in a pipeline fashion the computation of the fast Fourier transform (FFT) of a time-domain sampled complex digital data stream. The particular architecture makes use of simple identical processors (called inner product processors) in a linear organization called a systolic array. Through computer simulation the new architecture to compute the FFT with systolic arrays was proved to be viable, and computed the FFT correctly and with the predicted particulars of operation. Integrated circuits to compute the operations expected of the vital node of the systolic architecture were proven feasible, and even with a 2 micron VLSI technology can execute the required operations in the required time. Actual construction of the integrated circuits was successful in one variant (fixed point) and unsuccessful in the other (floating point).

Long-Term Observations of Ocean Biogeochemistry with Nitrate and Oxygen Sensors in Apex Profiling Floats

NASA Astrophysics Data System (ADS)

Johnson, K. S.; Coletti, L.; Jannasch, H.; Martz, T.; Swift, D.; Riser, S.

2008-12-01

Long-term, autonomous observations of ocean biogeochemical cycles are now feasible with chemical sensors in profiling floats. These sensors will enable decadal-scale observations of trends in global ocean biogeochemical cycles. Here, we focus on measurements on nitrate and dissolved oxygen. The ISUS (In Situ Ultraviolet Spectrophotometer) optical nitrate sensor has been adapted to operate in a Webb Research, Apex profiling float. The Apex float is of the type used in the Argo array and is designed for multi-year, expendable deployments in the ocean. Floats park at 1000 m depth and make 60 nitrate and oxygen measurements at depth intervals ranging from 50 m below 400 m to 5 m in the upper 100 m as they profile to the surface. All data are transmitted to shore using the Iridium telemetry system and they are available on the Internet in near-real time. Floats equipped with ISUS and an Aanderaa oxygen sensor are capable of making 280 vertical profiles from 1000 m. At a 5 day cycle time, the floats should have nearly a four year endurance. Three floats have now been deployed at the Hawaii Ocean Time series station (HOT), Ocean Station Papa (OSP) in the Gulf of Alaska and at 50 South, 30 East in the Southern Ocean. Two additional floats are designated for deployment at the Bermuda Atlantic Time Series station (BATS) and in the Drake Passage. The HOT float has made 56 profiles over 260 days and should continue operating for 3 more years. Nitrate concentrations are in excellent agreement with the long-term mean observed at HOT. No significant long-term drift in sensor response has occurred. A variety of features have been observed in the HOT nitrate data that are linked to contemporaneous changes in oxygen production and mesoscale dynamics. The impacts of these features will be briefly described. The Southern Ocean float has operated for 200 days and is now observing reinjection of nitrate into surface waters as winter mixing occurs(surface nitrate > 24 micromolar). We expect that the OSP and Southern Ocean floats will provide a quantitative measurement of the timing and magnitude of the spring bloom via the drawdown of surface nitrate. We are funded through NSF and NOPP to continue float deployments at HOT, BATS, OSP and the Southern Ocean for the next 3 years and to refine the sensor so it can be offered as a commercial option for all float users. New sensors in development for float deployments include a stable ISFET pH sensor.

Impact of associated injuries in the Floating knee: A retrospective study

PubMed Central

Rethnam, Ulfin; Yesupalan, Rajam S; Nair, Rajagopalan

2009-01-01

Background Floating knee injuries are usually associated with other significant injuries. Do these injuries have implications on the management of the floating knee and the final outcome of patients? Our study aims to assess the implications of associated injuries in the management and final outcome of floating knee. Methods 29 patients with floating knees were assessed in our institution. A retrospective analysis of medical records and radiographs were done and all associated injuries were identified. The impact of associated injuries on delay in initial surgical management, delay in rehabilitation & final outcome of the floating knee were assessed. Results 38 associated injuries were noted. 7 were associated with ipsilateral knee injuries. Lower limb injuries were most commonly associated with the floating knee. Patients with some associated injuries had a delay in surgical management and others a delay in post-operative rehabilitation. Knee ligament and vascular injuries were associated with poor outcome. Conclusion The associated injuries were quite frequent with the floating knee. Some of the associated injuries caused a delay in surgical management and post-operative rehabilitation. In assessment of the final outcome, patients with associated knee and vascular injuries had a poor prognosis. Majority of the patients with associated injuries had a good or excellent outcome. PMID:19144197

40 CFR 63.695 - Inspection and monitoring requirements.

Code of Federal Regulations, 2010 CFR

2010-07-01

... monitoring procedures required to perform the following: (1) To inspect tank fixed roofs and floating roofs... and floating roof inspection requirements. (1) Owners and operators that use a tank equipped with an internal floating roof in accordance with the provisions of § 63.685(e) of this subpart shall meet the...

Reducing float coal dust

PubMed Central

Patts, J.R.; Colinet, J.F.; Janisko, S.J.; Barone, T.L.; Patts, L.D.

2016-01-01

Controlling float coal dust in underground coal mines before dispersal into the general airstream can reduce the risk of mine explosions while potentially achieving a more effective and efficient use of rock dust. A prototype flooded-bed scrubber was evaluated for float coal dust control in the return of a continuous miner section. The scrubber was installed inline between the face ventilation tubing and an exhausting auxiliary fan. Airborne and deposited dust mass measurements were collected over three days at set distances from the fan exhaust to assess changes in float coal dust levels in the return due to operation of the scrubber. Mass-based measurements were collected on a per-cut basis and normalized on the basis of per ton mined by the continuous miner. The results show that average float coal dust levels measured under baseline conditions were reduced by more than 90 percent when operating the scrubber. PMID:28018004

Flight Operations Analysis Tool

NASA Technical Reports Server (NTRS)

Easter, Robert; Herrell, Linda; Pomphrey, Richard; Chase, James; Wertz Chen, Julie; Smith, Jeffrey; Carter, Rebecca

2006-01-01

Flight Operations Analysis Tool (FLOAT) is a computer program that partly automates the process of assessing the benefits of planning spacecraft missions to incorporate various combinations of launch vehicles and payloads. Designed primarily for use by an experienced systems engineer, FLOAT makes it possible to perform a preliminary analysis of trade-offs and costs of a proposed mission in days, whereas previously, such an analysis typically lasted months. FLOAT surveys a variety of prior missions by querying data from authoritative NASA sources pertaining to 20 to 30 mission and interface parameters that define space missions. FLOAT provides automated, flexible means for comparing the parameters to determine compatibility or the lack thereof among payloads, spacecraft, and launch vehicles, and for displaying the results of such comparisons. Sparseness, typical of the data available for analysis, does not confound this software. FLOAT effects an iterative process that identifies modifications of parameters that could render compatible an otherwise incompatible mission set.

Software Techniques for Non-Von Neumann Architectures

DTIC Science & Technology

1990-01-01

Commtopo programmable Benes net.; hypercubic lattice for QCD Control CENTRALIZED Assign STATIC Memory :SHARED Synch UNIVERSAL Max-cpu 566 Proessor...boards (each = 4 floating point units, 2 multipliers) Cpu-size 32-bit floating point chips Perform 11.4 Gflops Market quantum chromodynamics ( QCD ...functions there should exist a capability to define hierarchies and lattices of complex objects. A complex object can be made up of a set of simple objects

Interpretation of IEEE-854 floating-point standard and definition in the HOL system

NASA Technical Reports Server (NTRS)

Carreno, Victor A.

1995-01-01

The ANSI/IEEE Standard 854-1987 for floating-point arithmetic is interpreted by converting the lexical descriptions in the standard into mathematical conditional descriptions organized in tables. The standard is represented in higher-order logic within the framework of the HOL (Higher Order Logic) system. The paper is divided in two parts with the first part the interpretation and the second part the description in HOL.

77 FR 20295 - United States Navy Restricted Area, Menominee River, Marinette Marine Corporation Shipyard...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-04

... to the point of origin. The restricted area will be marked by a lighted and signed floating buoy line... a signed floating buoy line without permission from the Supervisor of Shipbuilding, Conversion and...

An Analysis of the Full-Floating Journal Bearing

NASA Technical Reports Server (NTRS)

Shaw, M C; Nussdorfer, T J , Jr

1947-01-01

An analysis of the operating characteristics of a full-floating journal bearing, a bearing in which a floating sleeve is located between the journal and bearing surfaces, is presented together with charts from which the performance of such bearings may be predicted. Examples are presented to illustrate the use of these charts and a limited number of experiments conducted upon a glass full-floating bearing are reported to verify some results of the analysis.

Real-time speech encoding based on Code-Excited Linear Prediction (CELP)

NASA Technical Reports Server (NTRS)

Leblanc, Wilfrid P.; Mahmoud, S. A.

1988-01-01

This paper reports on the work proceeding with regard to the development of a real-time voice codec for the terrestrial and satellite mobile radio environments. The codec is based on a complexity reduced version of code-excited linear prediction (CELP). The codebook search complexity was reduced to only 0.5 million floating point operations per second (MFLOPS) while maintaining excellent speech quality. Novel methods to quantize the residual and the long and short term model filters are presented.

Fix-Forward: A Comparison of the Army’s Requirements and Capabilities for Forward Support Maintenance,

DTIC Science & Technology

1983-04-01

tolerances or spaci - able assets diagnostic/fault ness float fications isolation devices Operation of cannibalL- zation point Why Sustain materiel...with diagnostic software based on "fault tree " representation of the M65 ThS) to bridge the gap in diagnostics capability was demonstrated in 1980 and... identification friend or foe) which has much lower reliability than TSQ-73 peculiar hardware). Thus, as in other examples, reported readiness does not reflect

RRTMGP: A High-Performance Broadband Radiation Code for the Next Decade

DTIC Science & Technology

2014-09-30

Hardware counters were used to measure several performance metrics, including the number of double-precision (DP) floating- point operations ( FLOPs ...0.2 DP FLOPs per CPU cycle. Experience with production science code is that it is possible to achieve execution rates in the range of 0.5 to 1.0...DP FLOPs per cycle. Looking at the ratio of vectorized DP FLOPs to total DP FLOPs we see (Figure PROF) that for most of the execution time the

Acceleration of Radiance for Lighting Simulation by Using Parallel Computing with OpenCL

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zuo, Wangda; McNeil, Andrew; Wetter, Michael

2011-09-06

We report on the acceleration of annual daylighting simulations for fenestration systems in the Radiance ray-tracing program. The algorithm was optimized to reduce both the redundant data input/output operations and the floating-point operations. To further accelerate the simulation speed, the calculation for matrix multiplications was implemented using parallel computing on a graphics processing unit. We used OpenCL, which is a cross-platform parallel programming language. Numerical experiments show that the combination of the above measures can speed up the annual daylighting simulations 101.7 times or 28.6 times when the sky vector has 146 or 2306 elements, respectively.

A decimal carry-free adder

NASA Astrophysics Data System (ADS)

Nikmehr, Hooman; Phillips, Braden; Lim, Cheng-Chew

2005-02-01

Recently, decimal arithmetic has become attractive in the financial and commercial world including banking, tax calculation, currency conversion, insurance and accounting. Although computers are still carrying out decimal calculation using software libraries and binary floating-point numbers, it is likely that in the near future, all processors will be equipped with units performing decimal operations directly on decimal operands. One critical building block for some complex decimal operations is the decimal carry-free adder. This paper discusses the mathematical framework of the addition, introduces a new signed-digit format for representing decimal numbers and presents an efficient architectural implementation. Delay estimation analysis shows that the adder offers improved performance over earlier designs.

Hardware math for the 6502 microprocessor

NASA Technical Reports Server (NTRS)

Kissel, R.; Currie, J.

1985-01-01

A floating-point arithmetic unit is described which is being used in the Ground Facility of Large Space Structures Control Verification (GF/LSSCV). The experiment uses two complete inertial measurement units and a set of three gimbal torquers in a closed loop to control the structural vibrations in a flexible test article (beam). A 6502 (8-bit) microprocessor controls four AMD 9511A floating-point arithmetic units to do all the computation in 20 milliseconds.

Term Cancellations in Computing Floating-Point Gröbner Bases

NASA Astrophysics Data System (ADS)

Sasaki, Tateaki; Kako, Fujio

We discuss the term cancellation which makes the floating-point Gröbner basis computation unstable, and show that error accumulation is never negligible in our previous method. Then, we present a new method, which removes accumulated errors as far as possible by reducing matrices constructed from coefficient vectors by the Gaussian elimination. The method manifests amounts of term cancellations caused by the existence of approximate linearly dependent relations among input polynomials.

Common Pitfalls in F77 Code Conversion

DTIC Science & Technology

2003-02-01

implementation versus another are the source of these errors rather than typography . It is well to use the practice of commenting-out original source file lines...identifier), every I in the format field must be replaced with f followed by an appropriate floating point format designator . Floating point numeric...helps even more. Finally, libraries are a major source of non-portablility[sic], with graphics libraries one of the chief culprits. We in Fusion

14 CFR 136.11 - Helicopter floats for over water.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 3 2011-01-01 2011-01-01 false Helicopter floats for over water. 136.11 Section 136.11 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) AIR CARRIERS AND OPERATORS FOR COMPENSATION OR HIRE: CERTIFICATION AND OPERATIONS COMMERCIAL AIR TOURS AND NATIONAL PARKS AIR TOUR MANAGEMEN...

High-Level Operations in Nonprocedural Programming Languages.

DTIC Science & Technology

1983-12-01

defining type specific operators. Abstract data type has been applied to the nonprocedural language NOPAL [Sang8O]. It was primarily used as a tool...level operation is transformed using the integral operation MATINV as follows: 1 GA IS GROUP, 2 GRA(*) IS GROUP, 3 AUX(*) IS FIELD (DEC FLOAT); I GI...IS GROUP, 2 GRI(*) IS GROUP, 3 INV(*) IS FIELD (DEC FLOAT); AUX = A; GI = MATINV( GA ); C = INV; In code generation, the assertion GI=MATINV( GA ) is

Design And Testing of The Floating Potential Probe For ISS

NASA Technical Reports Server (NTRS)

Hillard, G. Barry; Ferguson, Dale C.

2001-01-01

Flight 4A was an especially critical mission for the International Space Station (ISS). For the first time, the high voltage solar arrays generated significant amounts of power and long predicted environmental interactions (high negative floating potential and concomitant dielectric charging) became serious concerns. Furthermore, the same flight saw the Plasma Contacting Unit (PCU) deployed and put into operation to mitigate and control these effects. The ISS program office has recognized the critical need to verify, by direct measurement, that ISS does not charge to unacceptable levels. A Floating Potential Probe (FPP) was therefore deployed on ISS to measure ISS floating potential relative to the surrounding plasma and to measure relevant plasma parameters. The primary objective of FPP is to verify that ISS floating potential does not exceed the specified level of 40 volts with respect to the ambient. Since it is expected that in normal operations the PCU will maintain ISS within this specification, it is equivalent to say that the objective of FPP is to monitor the functionality of the PCU. In this paper, we report on the design and testing of the ISS FPP. In a separate paper, the operations and results obtained so far by the FPP will be presented.

Modification and fixed-point analysis of a Kalman filter for orientation estimation based on 9D inertial measurement unit data.

PubMed

Brückner, Hans-Peter; Spindeldreier, Christian; Blume, Holger

2013-01-01

A common approach for high accuracy sensor fusion based on 9D inertial measurement unit data is Kalman filtering. State of the art floating-point filter algorithms differ in their computational complexity nevertheless, real-time operation on a low-power microcontroller at high sampling rates is not possible. This work presents algorithmic modifications to reduce the computational demands of a two-step minimum order Kalman filter. Furthermore, the required bit-width of a fixed-point filter version is explored. For evaluation real-world data captured using an Xsens MTx inertial sensor is used. Changes in computational latency and orientation estimation accuracy due to the proposed algorithmic modifications and fixed-point number representation are evaluated in detail on a variety of processing platforms enabling on-board processing on wearable sensor platforms.

Compute Server Performance Results

NASA Technical Reports Server (NTRS)

Stockdale, I. E.; Barton, John; Woodrow, Thomas (Technical Monitor)

1994-01-01

Parallel-vector supercomputers have been the workhorses of high performance computing. As expectations of future computing needs have risen faster than projected vector supercomputer performance, much work has been done investigating the feasibility of using Massively Parallel Processor systems as supercomputers. An even more recent development is the availability of high performance workstations which have the potential, when clustered together, to replace parallel-vector systems. We present a systematic comparison of floating point performance and price-performance for various compute server systems. A suite of highly vectorized programs was run on systems including traditional vector systems such as the Cray C90, and RISC workstations such as the IBM RS/6000 590 and the SGI R8000. The C90 system delivers 460 million floating point operations per second (FLOPS), the highest single processor rate of any vendor. However, if the price-performance ration (PPR) is considered to be most important, then the IBM and SGI processors are superior to the C90 processors. Even without code tuning, the IBM and SGI PPR's of 260 and 220 FLOPS per dollar exceed the C90 PPR of 160 FLOPS per dollar when running our highly vectorized suite,

Test report for 120-inch-diameter Solid Rocket Booster (SRB) model tests. [floating and towing characteristics of space shuttle boosters

NASA Technical Reports Server (NTRS)

Jones, W. C.

1973-01-01

The space shuttle solid rocket boosters (SRB's) will be jettisoned to impact in the ocean within a 200-mile radius of the launch site. Tests were conducted at Long Beach, California, using a 12-inch diameter Titan 3C model to simulate the full-scale characteristics of the prototype SRB during retrieval operations. The objectives of the towing tests were to investigate and assess the following: (1) a floating and towing characteristics of the SRB; (2) need for plugging the SRB nozzle prior to tow; (3) attach point locations on the SRB; (4) effects of varying the SRB configuration; (5) towing hardware; and (6) difficulty of attaching a tow line to the SRB in the open sea. The model was towed in various sea states using four different types and varying lengths of tow line at various speeds. Three attach point locations were tested. Test data was recorded on magnetic tape for the tow line loads and for model pitch, roll, and yaw characteristics and was reduced by computer to tabular printouts and X-Y plots. Profile and movie photography provided documentary test data.

A comparison of the Cray-2 performance before and after the installation of memory pseudo-banking

NASA Technical Reports Server (NTRS)

Schmickley, Ronald D.; Bailey, David H.

1987-01-01

A suite of 13 large Fortran benchmark codes were run on a Cray-2 configured with memory pseudo-banking circuits, and floating point operation rates were measured for each under a variety of system load configurations. These were compared with similar flop measurements taken on the same system before installation of the pseudo-banking. A useful memory access efficiency parameter was defined and calculated for both sets of performance rates, allowing a crude quantitative measure of the improvement in efficiency due to pseudo-banking. Programs were categorized as either highly scalar (S) or highly vectorized (V) and either memory-intensive or register-intensive, giving 4 categories: S-memory, S-register, V-memory, and V-register. Using flop rates as a simple quantifier of these 4 categories, a scatter plot of efficiency gain vs Mflops roughly illustrates the improvement in floating point processing speed due to pseudo-banking. On the Cray-2 system tested this improvement ranged from 1 percent for S-memory codes to about 12 percent for V-memory codes. No significant gains were made for V-register codes, which was to be expected.

Floating Magnet Demonstration.

ERIC Educational Resources Information Center

Wake, Masayoshi

1990-01-01

A room-temperature demonstration of a floating magnet using a high-temperature superconductor is described. The setup and operation of the apparatus are described. The technical details of the effect are discussed. (CW)

40 CFR 63.120 - Storage vessel provisions-procedures to determine compliance.

Code of Federal Regulations, 2010 CFR

2010-07-01

... with § 63.119(b) of this subpart (storage vessel equipped with a fixed roof and internal floating roof) or with § 63.119(d) of this subpart (storage vessel equipped with an external floating roof converted to an internal floating roof), the owner or operator shall comply with the requirements in paragraphs...

Physical implication of transition voltage in organic nano-floating-gate nonvolatile memories

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, Shun; Gao, Xu, E-mail: wangsd@suda.edu.cn, E-mail: gaoxu@suda.edu.cn; Zhong, Ya-Nan

High-performance pentacene-based organic field-effect transistor nonvolatile memories, using polystyrene as a tunneling dielectric and Au nanoparticles as a nano-floating-gate, show parallelogram-like transfer characteristics with a featured transition point. The transition voltage at the transition point corresponds to a threshold electric field in the tunneling dielectric, over which stored electrons in the nano-floating-gate will start to leak out. The transition voltage can be modulated depending on the bias configuration and device structure. For p-type active layers, optimized transition voltage should be on the negative side of but close to the reading voltage, which can simultaneously achieve a high ON/OFF ratio andmore » good memory retention.« less

Design of crossed-mirror array to form floating 3D LED signs

NASA Astrophysics Data System (ADS)

Yamamoto, Hirotsugu; Bando, Hiroki; Kujime, Ryousuke; Suyama, Shiro

2012-03-01

3D representation of digital signage improves its significance and rapid notification of important points. Our goal is to realize floating 3D LED signs. The problem is there is no sufficient device to form floating 3D images from LEDs. LED lamp size is around 1 cm including wiring and substrates. Such large pitch increases display size and sometimes spoils image quality. The purpose of this paper is to develop optical device to meet the three requirements and to demonstrate floating 3D arrays of LEDs. We analytically investigate image formation by a crossed mirror structure with aerial aperture, called CMA (crossed-mirror array). CMA contains dihedral corner reflectors at each aperture. After double reflection, light rays emitted from an LED will converge into the corresponding image point. We have fabricated CMA for 3D array of LEDs. One CMA unit contains 20 x 20 apertures that are located diagonally. Floating image of LEDs was formed in wide range of incident angle. The image size of focused beam agreed to the apparent aperture size. When LEDs were located three-dimensionally (LEDs in three depths), the focused distances were the same as the distance between the real LED and the CMA.

DSS 13 Microprocessor Antenna Controller

NASA Technical Reports Server (NTRS)

Gosline, R. M.

1984-01-01

A microprocessor based antenna controller system developed as part of the unattended station project for DSS 13 is described. Both the hardware and software top level designs are presented and the major problems encounted are discussed. Developments useful to related projects include a JPL standard 15 line interface using a single board computer, a general purpose parser, a fast floating point to ASCII conversion technique, and experience gained in using off board floating point processors with the 8080 CPU.

Toward a formal verification of a floating-point coprocessor and its composition with a central processing unit

NASA Technical Reports Server (NTRS)

Pan, Jing; Levitt, Karl N.; Cohen, Gerald C.

1991-01-01

Discussed here is work to formally specify and verify a floating point coprocessor based on the MC68881. The HOL verification system developed at Cambridge University was used. The coprocessor consists of two independent units: the bus interface unit used to communicate with the cpu and the arithmetic processing unit used to perform the actual calculation. Reasoning about the interaction and synchronization among processes using higher order logic is demonstrated.

High-precision arithmetic in mathematical physics

DOE PAGES

Bailey, David H.; Borwein, Jonathan M.

2015-05-12

For many scientific calculations, particularly those involving empirical data, IEEE 32-bit floating-point arithmetic produces results of sufficient accuracy, while for other applications IEEE 64-bit floating-point is more appropriate. But for some very demanding applications, even higher levels of precision are often required. Furthermore, this article discusses the challenge of high-precision computation, in the context of mathematical physics, and highlights what facilities are required to support future computation, in light of emerging developments in computer architecture.

The Aerodynamic Drag of Five Models of Side Floats N.A.C.A. Models 51-E, 51-F, 51-G, 51-H, 51-J

NASA Technical Reports Server (NTRS)

House, R O

1938-01-01

The drag of five models of side floats was measured in the N.A.C.A. 7- by 10-foot wind tunnel. The most promising method of reducing the drag of floats indicated by these tests is lowering the angle at which the floats are rigged. The addition of a step to a float does not always increase the drag in the flying range, floats with steps sometimes having lower drag than similar floats without steps. Making the bow chine no higher than necessary might result in a reduction in air drag because of the lower angle of pitch of the chines. Since side floats are used formally to obtain lateral stability when the seaplane is operating on the water at slow speeds or at rest, greater consideration can be given to factors affecting aerodynamic drag than is possible for other types of floats and hulls.

Computationally efficient control allocation

NASA Technical Reports Server (NTRS)

Durham, Wayne (Inventor)

2001-01-01

A computationally efficient method for calculating near-optimal solutions to the three-objective, linear control allocation problem is disclosed. The control allocation problem is that of distributing the effort of redundant control effectors to achieve some desired set of objectives. The problem is deemed linear if control effectiveness is affine with respect to the individual control effectors. The optimal solution is that which exploits the collective maximum capability of the effectors within their individual physical limits. Computational efficiency is measured by the number of floating-point operations required for solution. The method presented returned optimal solutions in more than 90% of the cases examined; non-optimal solutions returned by the method were typically much less than 1% different from optimal and the errors tended to become smaller than 0.01% as the number of controls was increased. The magnitude of the errors returned by the present method was much smaller than those that resulted from either pseudo inverse or cascaded generalized inverse solutions. The computational complexity of the method presented varied linearly with increasing numbers of controls; the number of required floating point operations increased from 5.5 i, to seven times faster than did the minimum-norm solution (the pseudoinverse), and at about the same rate as did the cascaded generalized inverse solution. The computational requirements of the method presented were much better than that of previously described facet-searching methods which increase in proportion to the square of the number of controls.

Design of permanent magnet synchronous motor speed control system based on SVPWM

NASA Astrophysics Data System (ADS)

Wu, Haibo

2017-04-01

The control system is designed to realize TMS320F28335 based on the permanent magnet synchronous motor speed control system, and put it to quoting all electric of injection molding machine. The system of the control method used SVPWM, through the sampling motor current and rotating transformer position information, realize speed, current double closed loop control. Through the TMS320F28335 hardware floating-point processing core, realize the application for permanent magnet synchronous motor in the floating point arithmetic, to replace the past fixed-point algorithm, and improve the efficiency of the code.

On the Floating Point Performance of the i860 Microprocessor

NASA Technical Reports Server (NTRS)

Lee, King; Kutler, Paul (Technical Monitor)

1997-01-01

The i860 microprocessor is a pipelined processor that can deliver two double precision floating point results every clock. It is being used in the Touchstone project to develop a teraflop computer by the year 2000. With such high computational capabilities it was expected that memory bandwidth would limit performance on many kernels. Measured performance of three kernels showed performance is less than what memory bandwidth limitations would predict. This paper develops a model that explains the discrepancy in terms of memory latencies and points to some problems involved in moving data from memory to the arithmetic pipelines.

A novel control process of cyanobacterial bloom using cyanobacteriolytic bacteria immobilized in floating biodegradable plastic carriers.

PubMed

Nakamura, N; Nakano, K; Sugiura, N; Matsumura, M

2003-12-01

A process using a floating carrier for immobilization of cyanobacteriolytic bacteria, B.cereus N-14, was proposed to realize an effective in situ control of natural floating cyanobacterial blooms. The critical concentrations of the cyanobacteriolytic substance and B.cereus N-14 cells required to exhibit cyanobacteriolytic activity were investigated. The results indicated the necessity of cell growth to produce sufficiently high amounts of the cyanobacteriolytic substance to exhibit its activity and also for conditions enabling good contact between high concentrations of the cyanobacteriolytic substance and cyanobacteria. Floating biodegradable plastics made of starch were applied as a carrier material to maintain close contact between the immobilized cyanobacteriolytic bacteria and floating cyanobacteria. The floating starch-carriers could eliminate 99% of floating cyanobacteria in 4 d. Since B.cereus N-14 could produce the cyanobacteriolytic substance under the presence of starch and some amino acids, the cyanobacteriolytic activity could be attributed to carbon source fed from starch carrier and amino acids eluted from lysed cyanobacteria. Therefore, the effect of using a floating starch-carrier was confirmed from both view points as a carrier for immobilization and a nutrient source to stimulate cyanobacteriolytic activity. The new concept to apply a floating carrier immobilizing useful microorganisms for intensive treatment of a nuisance floating target was demonstrated.

The Floating Upper Limb: Multiple Injuries Involving Ipsilateral, Proximal, Humeral, Supracondylar, and Distal Radial Limb

PubMed Central

Manaan, Qazi; Bashir, Adil; Zahoor, Adnan; Mokhdomi, Taseem A.

2016-01-01

Floating arm injury represents a common yet complicated injury of the childhood severely associated with limb deformation and even morbidity, if not precisely addressed and credibly operated. Here, we report a rare floating upper limb case of a 9-year-old boy with multiple injuries of ipsilateral proximal humeral, supracondylar and distal radial limb. This is the first report to document such a combined floating elbow and floating arm injury in the same limb. In this report, we discuss the surgical procedures used and recovery of the patient monitored to ascertain the effectiveness of the method in limb reorganisation. PMID:27583121

The Floating Upper Limb: Multiple Injuries Involving Ipsilateral, Proximal, Humeral, Supracondylar, and Distal Radial Limb.

PubMed

Manaan, Qazi; Bashir, Adil; Zahoor, Adnan; Mokhdomi, Taseem A; Danish, Qazi

2016-09-01

Floating arm injury represents a common yet complicated injury of the childhood severely associated with limb deformation and even morbidity, if not precisely addressed and credibly operated. Here, we report a rare floating upper limb case of a 9-year-old boy with multiple injuries of ipsilateral proximal humeral, supracondylar and distal radial limb. This is the first report to document such a combined floating elbow and floating arm injury in the same limb. In this report, we discuss the surgical procedures used and recovery of the patient monitored to ascertain the effectiveness of the method in limb reorganisation.

WindWaveFloat (WWF): Final Scientific Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Alla Weinstein; Roddier, Dominique; Banister, Kevin

2012-03-30

Principle Power Inc. and National Renewable Energy Lab (NREL) have completed a contract to assess the technical and economic feasibility of integrating wave energy converters into the WindFloat, resulting in a new concept called the WindWaveFloat (WWF). The concentration of several devices on one platform could offer a potential for both economic and operational advantages. Wind and wave energy converters can share the electrical cable and power transfer equipment to transport the electricity to shore. Access to multiple generation devices could be simplified, resulting in cost saving at the operational level. Overall capital costs may also be reduced, provided thatmore » the design of the foundation can be adapted to multiple devices with minimum modifications. Finally, the WindWaveFloat confers the ability to increase energy production from individual floating support structures, potentially leading to a reduction in levelized energy costs, an increase in the overall capacity factor, and greater stability of the electrical power delivered to the grid. The research conducted under this grant investigated the integration of several wave energy device types into the WindFloat platform. Several of the resulting system designs demonstrated technical feasibility, but the size and design constraints of the wave energy converters (technical and economic) make the WindWaveFloat concept economically unfeasible at this time. Not enough additional generation could be produced to make the additional expense associated with wave energy conversion integration into the WindFloat worthwhile.« less

Bathymetry in Petermann fjord from Operation IceBridge aerogravity

NASA Astrophysics Data System (ADS)

Tinto, Kirsty J.; Bell, Robin E.; Cochran, James R.; Münchow, Andreas

2015-07-01

Petermann Glacier is a major glacier in northern Greenland, maintaining one of the few remaining floating ice tongues in Greenland. Monitoring programs, such as NASA's Operation IceBridge have surveyed Petermann Glacier over several decades and have found it to be stable in terms of mass balance, velocity and grounding-line position. The future vulnerability of this large glacier to changing ocean temperatures and climate depends on the ocean-ice interactions beneath its floating tongue. These cannot currently be predicted due to a lack of knowledge of the bathymetry underneath the ice tongue. Here we use aerogravity data from Operation IceBridge, together with airborne radar and laser data and shipborne bathymetry-soundings to model the bathymetry beneath the Petermann ice tongue. We find a basement-cored inner sill at 540-610 m depth that results in a water cavity with minimum thickness of 400 m about 25 km from the grounding line. The sill is coincident with the location of the melt rate minimum. Seaward of the sill the fjord is strongly asymmetric. The deepest point occurs on the eastern side of the fjord at 1150 m, 600 m deeper than on the western side. This asymmetry is due to a sedimentary deposit on the western side of the fjord. A 350-410 m-deep outer sill, also mapped by marine surveys, marks the seaward end of the fjord. This outer sill is aligned with the proposed Last Glacial Maximum (LGM) grounding-line position for Petermann Glacier. The inner sill likely provided a stable pinning point for the grounding line in the past, punctuating the retreat of Petermann Glacier since the LGM.

Formal verification of mathematical software

NASA Technical Reports Server (NTRS)

Sutherland, D.

1984-01-01

Methods are investigated for formally specifying and verifying the correctness of mathematical software (software which uses floating point numbers and arithmetic). Previous work in the field was reviewed. A new model of floating point arithmetic called the asymptotic paradigm was developed and formalized. Two different conceptual approaches to program verification, the classical Verification Condition approach and the more recently developed Programming Logic approach, were adapted to use the asymptotic paradigm. These approaches were then used to verify several programs; the programs chosen were simplified versions of actual mathematical software.

Universal Number Library

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lloyd, G. Scott

This floating-point arithmetic library contains a software implementation of Universal Numbers (unums) as described by John Gustafson [1]. The unum format is a superset of IEEE 754 floating point with several advantages. Computing with unums provides more accurate answers without rounding errors, underflow or overflow. In contrast to fixed-sized IEEE numbers, a variable number of bits can be used to encode unums. This all allows number with only a few significant digits or with a small dynamic range to be represented more compactly.

Constrained Chebyshev approximations to some elementary functions suitable for evaluation with floating point arithmetic

NASA Technical Reports Server (NTRS)

Manos, P.; Turner, L. R.

1972-01-01

Approximations which can be evaluated with precision using floating-point arithmetic are presented. The particular set of approximations thus far developed are for the function TAN and the functions of USASI FORTRAN excepting SQRT and EXPONENTIATION. These approximations are, furthermore, specialized to particular forms which are especially suited to a computer with a small memory, in that all of the approximations can share one general purpose subroutine for the evaluation of a polynomial in the square of the working argument.

An integrated circuit floating point accumulator

NASA Technical Reports Server (NTRS)

Goldsmith, T. C.

1977-01-01

Goddard Space Flight Center has developed a large scale integrated circuit (type 623) which can perform pulse counting, storage, floating point compression, and serial transmission, using a single monolithic device. Counts of 27 or 19 bits can be converted to transmitted values of 12 or 8 bits respectively. Use of the 623 has resulted in substantial savaings in weight, volume, and dollar resources on at least 11 scientific instruments to be flown on 4 NASA spacecraft. The design, construction, and application of the 623 are described.

Floating-point function generation routines for 16-bit microcomputers

NASA Technical Reports Server (NTRS)

Mackin, M. A.; Soeder, J. F.

1984-01-01

Several computer subroutines have been developed that interpolate three types of nonanalytic functions: univariate, bivariate, and map. The routines use data in floating-point form. However, because they are written for use on a 16-bit Intel 8086 system with an 8087 mathematical coprocessor, they execute as fast as routines using data in scaled integer form. Although all of the routines are written in assembly language, they have been implemented in a modular fashion so as to facilitate their use with high-level languages.

Floating-point geometry: toward guaranteed geometric computations with approximate arithmetics

NASA Astrophysics Data System (ADS)

Bajard, Jean-Claude; Langlois, Philippe; Michelucci, Dominique; Morin, Géraldine; Revol, Nathalie

2008-08-01

Geometric computations can fail because of inconsistencies due to floating-point inaccuracy. For instance, the computed intersection point between two curves does not lie on the curves: it is unavoidable when the intersection point coordinates are non rational, and thus not representable using floating-point arithmetic. A popular heuristic approach tests equalities and nullities up to a tolerance ɛ. But transitivity of equality is lost: we can have A approx B and B approx C, but A not approx C (where A approx B means ||A - B|| < ɛ for A,B two floating-point values). Interval arithmetic is another, self-validated, alternative; the difficulty is to limit the swell of the width of intervals with computations. Unfortunately interval arithmetic cannot decide equality nor nullity, even in cases where it is decidable by other means. A new approach, developed in this paper, consists in modifying the geometric problems and algorithms, to account for the undecidability of the equality test and unavoidable inaccuracy. In particular, all curves come with a non-zero thickness, so two curves (generically) cut in a region with non-zero area, an inner and outer representation of which is computable. This last approach no more assumes that an equality or nullity test is available. The question which arises is: which geometric problems can still be solved with this last approach, and which cannot? This paper begins with the description of some cases where every known arithmetic fails in practice. Then, for each arithmetic, some properties of the problems they can solve are given. We end this work by proposing the bases of a new approach which aims to fulfill the geometric computations requirements.

ROStoJAUSBridge Manual

DTIC Science & Technology

2012-03-01

Description A dass that handles Imming the JAUS header pmUon of JAUS messages. jaus_hmd~_msg is included as a data member in all JAUS messages. Member...scaleTolnt16 (float val, float low, float high) [related] Scales signed short value val, which is bounded by low and high. Shifts the center point of low...and high to zero, and shifts val accordingly. V a! is then up scaled by the ratio of the range of short values to the range of values from high to low

33 CFR 146.104 - Safety and Security notice of arrival for foreign floating facilities.

Code of Federal Regulations, 2011 CFR

2011-07-01

... the NVMC's Web site at http://www.nvmc.uscg.gov/. (c) Updates to a submitted NOA. Unless otherwise... owner or operator of the foreign floating facility must revise and re-submit the NOA within the times required in paragraph (e) of this section. An owner or operator does not need to revise or re-submit an NOA...

33 CFR 146.104 - Safety and Security notice of arrival for foreign floating facilities.

Code of Federal Regulations, 2012 CFR

2012-07-01

... the NVMC's Web site at http://www.nvmc.uscg.gov/. (c) Updates to a submitted NOA. Unless otherwise... owner or operator of the foreign floating facility must revise and re-submit the NOA within the times required in paragraph (e) of this section. An owner or operator does not need to revise or re-submit an NOA...

33 CFR 146.104 - Safety and Security notice of arrival for foreign floating facilities.

Code of Federal Regulations, 2014 CFR

2014-07-01

... the NVMC's Web site at http://www.nvmc.uscg.gov/. (c) Updates to a submitted NOA. Unless otherwise... owner or operator of the foreign floating facility must revise and re-submit the NOA within the times required in paragraph (e) of this section. An owner or operator does not need to revise or re-submit an NOA...

33 CFR 146.104 - Safety and Security notice of arrival for foreign floating facilities.

Code of Federal Regulations, 2013 CFR

2013-07-01

... the NVMC's Web site at http://www.nvmc.uscg.gov/. (c) Updates to a submitted NOA. Unless otherwise... owner or operator of the foreign floating facility must revise and re-submit the NOA within the times required in paragraph (e) of this section. An owner or operator does not need to revise or re-submit an NOA...

Evaluation of Biodiesel Fuels to Reduce Fossil Fuel Use in Corps of Engineers Floating Plant Operations

DTIC Science & Technology

2016-07-01

ER D C/ CH L TR -1 6- 11 Dredging Operations and Environmental Research Program Evaluation of Biodiesel Fuels to Reduce Fossil Fuel Use...Fuels to Reduce Fossil Fuel Use in Corps of Engineers Floating Plant Operations Michael Tubman and Timothy Welp Coastal and Hydraulics Laboratory...sensitive emissions, increase use of renewable energy, and reduce the use of fossil fuels was conducted with funding from the U.S. Army Corps of

A sparse matrix algorithm on the Boolean vector machine

NASA Technical Reports Server (NTRS)

Wagner, Robert A.; Patrick, Merrell L.

1988-01-01

VLSI technology is being used to implement a prototype Boolean Vector Machine (BVM), which is a large network of very small processors with equally small memories that operate in SIMD mode; these use bit-serial arithmetic, and communicate via cube-connected cycles network. The BVM's bit-serial arithmetic and the small memories of individual processors are noted to compromise the system's effectiveness in large numerical problem applications. Attention is presently given to the implementation of a basic matrix-vector iteration algorithm for space matrices of the BVM, in order to generate over 1 billion useful floating-point operations/sec for this iteration algorithm. The algorithm is expressed in a novel language designated 'BVM'.

CANVAS FINISH TO REMOVE FLOAT MARKS. View is to the ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

CANVAS FINISH TO REMOVE FLOAT MARKS. View is to the northwest of deck finishing operations - South Fork Trinity River Bridge, State Highway 299 spanning South Fork Trinity River, Salyer, Trinity County, CA

Numerical computation of spherical harmonics of arbitrary degree and order by extending exponent of floating point numbers

NASA Astrophysics Data System (ADS)

Fukushima, Toshio

2012-04-01

By extending the exponent of floating point numbers with an additional integer as the power index of a large radix, we compute fully normalized associated Legendre functions (ALF) by recursion without underflow problem. The new method enables us to evaluate ALFs of extremely high degree as 232 = 4,294,967,296, which corresponds to around 1 cm resolution on the Earth's surface. By limiting the application of exponent extension to a few working variables in the recursion, choosing a suitable large power of 2 as the radix, and embedding the contents of the basic arithmetic procedure of floating point numbers with the exponent extension directly in the program computing the recurrence formulas, we achieve the evaluation of ALFs in the double-precision environment at the cost of around 10% increase in computational time per single ALF. This formulation realizes meaningful execution of the spherical harmonic synthesis and/or analysis of arbitrary degree and order.

Hash function based on chaotic map lattices.

PubMed

Wang, Shihong; Hu, Gang

2007-06-01

A new hash function system, based on coupled chaotic map dynamics, is suggested. By combining floating point computation of chaos and some simple algebraic operations, the system reaches very high bit confusion and diffusion rates, and this enables the system to have desired statistical properties and strong collision resistance. The chaos-based hash function has its advantages for high security and fast performance, and it serves as one of the most highly competitive candidates for practical applications of hash function for software realization and secure information communications in computer networks.

Programmable architecture for pixel level processing tasks in lightweight strapdown IR seekers

NASA Astrophysics Data System (ADS)

Coates, James L.

1993-06-01

Typical processing tasks associated with missile IR seeker applications are described, and a straw man suite of algorithms is presented. A fully programmable multiprocessor architecture is realized on a multimedia video processor (MVP) developed by Texas Instruments. The MVP combines the elements of RISC, floating point, advanced DSPs, graphics processors, display and acquisition control, RAM, and external memory. Front end pixel level tasks typical of missile interceptor applications, operating on 256 x 256 sensor imagery, can be processed at frame rates exceeding 100 Hz in a single MVP chip.

Hash function based on chaotic map lattices

NASA Astrophysics Data System (ADS)

Wang, Shihong; Hu, Gang

2007-06-01

A new hash function system, based on coupled chaotic map dynamics, is suggested. By combining floating point computation of chaos and some simple algebraic operations, the system reaches very high bit confusion and diffusion rates, and this enables the system to have desired statistical properties and strong collision resistance. The chaos-based hash function has its advantages for high security and fast performance, and it serves as one of the most highly competitive candidates for practical applications of hash function for software realization and secure information communications in computer networks.

Research on crude oil storage and transportation based on optimization algorithm

NASA Astrophysics Data System (ADS)

Yuan, Xuhua

2018-04-01

At present, the optimization theory and method have been widely used in the optimization scheduling and optimal operation scheme of complex production systems. Based on C++Builder 6 program development platform, the theoretical research results are implemented by computer. The simulation and intelligent decision system of crude oil storage and transportation inventory scheduling are designed. The system includes modules of project management, data management, graphics processing, simulation of oil depot operation scheme. It can realize the optimization of the scheduling scheme of crude oil storage and transportation system. A multi-point temperature measuring system for monitoring the temperature field of floating roof oil storage tank is developed. The results show that by optimizing operating parameters such as tank operating mode and temperature, the total transportation scheduling costs of the storage and transportation system can be reduced by 9.1%. Therefore, this method can realize safe and stable operation of crude oil storage and transportation system.

Differential porosimetry and permeametry for random porous media.

PubMed

Hilfer, R; Lemmer, A

2015-07-01

Accurate determination of geometrical and physical properties of natural porous materials is notoriously difficult. Continuum multiscale modeling has provided carefully calibrated realistic microstructure models of reservoir rocks with floating point accuracy. Previous measurements using synthetic microcomputed tomography (μ-CT) were based on extrapolation of resolution-dependent properties for discrete digitized approximations of the continuum microstructure. This paper reports continuum measurements of volume and specific surface with full floating point precision. It also corrects an incomplete description of rotations in earlier publications. More importantly, the methods of differential permeametry and differential porosimetry are introduced as precision tools. The continuum microstructure chosen to exemplify the methods is a homogeneous, carefully calibrated and characterized model for Fontainebleau sandstone. The sample has been publicly available since 2010 on the worldwide web as a benchmark for methodical studies of correlated random media. High-precision porosimetry gives the volume and internal surface area of the sample with floating point accuracy. Continuum results with floating point precision are compared to discrete approximations. Differential porosities and differential surface area densities allow geometrical fluctuations to be discriminated from discretization effects and numerical noise. Differential porosimetry and Fourier analysis reveal subtle periodic correlations. The findings uncover small oscillatory correlations with a period of roughly 850μm, thus implying that the sample is not strictly stationary. The correlations are attributed to the deposition algorithm that was used to ensure the grain overlap constraint. Differential permeabilities are introduced and studied. Differential porosities and permeabilities provide scale-dependent information on geometry fluctuations, thereby allowing quantitative error estimates.

An Adaptive Prediction-Based Approach to Lossless Compression of Floating-Point Volume Data.

PubMed

Fout, N; Ma, Kwan-Liu

2012-12-01

In this work, we address the problem of lossless compression of scientific and medical floating-point volume data. We propose two prediction-based compression methods that share a common framework, which consists of a switched prediction scheme wherein the best predictor out of a preset group of linear predictors is selected. Such a scheme is able to adapt to different datasets as well as to varying statistics within the data. The first method, called APE (Adaptive Polynomial Encoder), uses a family of structured interpolating polynomials for prediction, while the second method, which we refer to as ACE (Adaptive Combined Encoder), combines predictors from previous work with the polynomial predictors to yield a more flexible, powerful encoder that is able to effectively decorrelate a wide range of data. In addition, in order to facilitate efficient visualization of compressed data, our scheme provides an option to partition floating-point values in such a way as to provide a progressive representation. We compare our two compressors to existing state-of-the-art lossless floating-point compressors for scientific data, with our data suite including both computer simulations and observational measurements. The results demonstrate that our polynomial predictor, APE, is comparable to previous approaches in terms of speed but achieves better compression rates on average. ACE, our combined predictor, while somewhat slower, is able to achieve the best compression rate on all datasets, with significantly better rates on most of the datasets.

Extending the BEAGLE library to a multi-FPGA platform.

PubMed

Jin, Zheming; Bakos, Jason D

2013-01-19

Maximum Likelihood (ML)-based phylogenetic inference using Felsenstein's pruning algorithm is a standard method for estimating the evolutionary relationships amongst a set of species based on DNA sequence data, and is used in popular applications such as RAxML, PHYLIP, GARLI, BEAST, and MrBayes. The Phylogenetic Likelihood Function (PLF) and its associated scaling and normalization steps comprise the computational kernel for these tools. These computations are data intensive but contain fine grain parallelism that can be exploited by coprocessor architectures such as FPGAs and GPUs. A general purpose API called BEAGLE has recently been developed that includes optimized implementations of Felsenstein's pruning algorithm for various data parallel architectures. In this paper, we extend the BEAGLE API to a multiple Field Programmable Gate Array (FPGA)-based platform called the Convey HC-1. The core calculation of our implementation, which includes both the phylogenetic likelihood function (PLF) and the tree likelihood calculation, has an arithmetic intensity of 130 floating-point operations per 64 bytes of I/O, or 2.03 ops/byte. Its performance can thus be calculated as a function of the host platform's peak memory bandwidth and the implementation's memory efficiency, as 2.03 × peak bandwidth × memory efficiency. Our FPGA-based platform has a peak bandwidth of 76.8 GB/s and our implementation achieves a memory efficiency of approximately 50%, which gives an average throughput of 78 Gflops. This represents a ~40X speedup when compared with BEAGLE's CPU implementation on a dual Xeon 5520 and 3X speedup versus BEAGLE's GPU implementation on a Tesla T10 GPU for very large data sizes. The power consumption is 92 W, yielding a power efficiency of 1.7 Gflops per Watt. The use of data parallel architectures to achieve high performance for likelihood-based phylogenetic inference requires high memory bandwidth and a design methodology that emphasizes high memory efficiency. To achieve this objective, we integrated 32 pipelined processing elements (PEs) across four FPGAs. For the design of each PE, we developed a specialized synthesis tool to generate a floating-point pipeline with resource and throughput constraints to match the target platform. We have found that using low-latency floating-point operators can significantly reduce FPGA area and still meet timing requirement on the target platform. We found that this design methodology can achieve performance that exceeds that of a GPU-based coprocessor.

Chemical Oxygen Demand abatement in sewage using Micro-Aeration Enhanced Ecological Floating Bed

NASA Astrophysics Data System (ADS)

Shi, Hongle; Zhou, Gaofeng; Liu, Yiqing; Tan, Jiancong; Fu, Yongsheng

2018-02-01

The traditional ecological floating bed combined with micro-aeration system and artificial medium was developed for the removal of contaminants and remediation of surface water. This micro-aeration enhanced ecological floating bed (MAEEFB) consisted of aeration unit, microbial processing unit and aquatic plant unit. Batch experiments were conducted in different operating conditions on the removal of chemical oxygen demand (COD) in the sewage using MAEEFB. The removal rate of COD by MAEEFB, enhanced ecological floating bed (EEFB) and traditional ecological floating bed (TEFB) in the same reaction conditions was 59.2%, 56.9% and 30.6%, respectively, indicating that the combination of micro-aeration system and artificial medium could enhance the removal efficiency of COD in TEFB. In MAEEFB, the aeration intensity should be designed reasonablely considering both treatment efficiency and operation cost. Only increasing the specific surface area of the packing cannot effectively improve the purification efficiency of water. Factors like packing material, ability of intercepting organics and complicated extent of microorganisms attaching on the packing should also be considered.

Float processing of high-temperature complex silicate glasses and float baths used for same

NASA Technical Reports Server (NTRS)

Cooper, Reid Franklin (Inventor); Cook, Glen Bennett (Inventor)

2000-01-01

A float glass process for production of high melting temperature glasses utilizes a binary metal alloy bath having the combined properties of a low melting point, low reactivity with oxygen, low vapor pressure, and minimal reactivity with the silicate glasses being formed. The metal alloy of the float medium is exothermic with a solvent metal that does not readily form an oxide. The vapor pressure of both components in the alloy is low enough to prevent deleterious vapor deposition, and there is minimal chemical and interdiffusive interaction of either component with silicate glasses under the float processing conditions. Alloys having the desired combination of properties include compositions in which gold, silver or copper is the solvent metal and silicon, germanium or tin is the solute, preferably in eutectic or near-eutectic compositions.

ICRF-Induced Changes in Floating Potential and Ion Saturation Current in the EAST Divertor

NASA Astrophysics Data System (ADS)

Perkins, Rory; Hosea, Joel; Taylor, Gary; Bertelli, Nicola; Kramer, Gerrit; Qin, Chengming; Wang, Liang; Yang, Jichan; Zhang, Xinjun

2017-10-01

Injection of waves in the ion cyclotron range of frequencies (ICRF) into a tokamak can potentially raise the plasma potential via RF rectification. Probes are affected both by changes in plasma potential and also by RF-averaging of the probe characteristic, with the latter tending to drop the floating potential. We present the effect of ICRF heating on divertor Langmuir probes in the EAST experiment. Over a scan of the outer gap, probes connected to the antennas have increases in floating potential with ICRF, but probes in between the outer-vessel strike point and flux surface tangent to the antenna have decreased floating potential. This behaviour is investigated using field-line mapping. Preliminary results show that mdiplane gas puffing can suppress the strong influence of ICRF on the probes' floating potential.

33 CFR 146.103 - Safety and Security notice of arrival for U.S. floating facilities.

Code of Federal Regulations, 2012 CFR

2012-07-01

... specified in the NVMC's Web site at http://www.nvmc.uscg.gov/. (c) Updates to a submitted NOA. Unless..., the owner or operator of a U.S. floating facility must revise and re-submit the NOA within the times required in paragraph (e) of this section. An owner or operator does not need to revise or re-submit an NOA...

33 CFR 146.103 - Safety and Security notice of arrival for U.S. floating facilities.

Code of Federal Regulations, 2011 CFR

2011-07-01

... specified in the NVMC's Web site at http://www.nvmc.uscg.gov/. (c) Updates to a submitted NOA. Unless..., the owner or operator of a U.S. floating facility must revise and re-submit the NOA within the times required in paragraph (e) of this section. An owner or operator does not need to revise or re-submit an NOA...

33 CFR 146.103 - Safety and Security notice of arrival for U.S. floating facilities.

Code of Federal Regulations, 2013 CFR

2013-07-01

... specified in the NVMC's Web site at http://www.nvmc.uscg.gov/. (c) Updates to a submitted NOA. Unless..., the owner or operator of a U.S. floating facility must revise and re-submit the NOA within the times required in paragraph (e) of this section. An owner or operator does not need to revise or re-submit an NOA...

33 CFR 146.103 - Safety and Security notice of arrival for U.S. floating facilities.

Code of Federal Regulations, 2014 CFR

2014-07-01

... specified in the NVMC's Web site at http://www.nvmc.uscg.gov/. (c) Updates to a submitted NOA. Unless..., the owner or operator of a U.S. floating facility must revise and re-submit the NOA within the times required in paragraph (e) of this section. An owner or operator does not need to revise or re-submit an NOA...

Lithium-ion drifting: Application to the study of point defects in floating-zone silicon

NASA Technical Reports Server (NTRS)

Walton, J. T.; Wong, Y. K.; Zulehner, W.

1997-01-01

The use of lithium-ion (Li(+)) drifting to study the properties of point defects in p-type Floating-Zone (FZ) silicon crystals is reported. The Li(+) drift technique is used to detect the presence of vacancy-related defects (D defects) in certain p-type FZ silicon crystals. SUPREM-IV modeling suggests that the silicon point defect diffusivities are considerably higher than those commonly accepted, but are in reasonable agreement with values recently proposed. These results demonstrate the utility of Li(+) drifting in the study of silicon point defect properties in p-type FZ crystals. Finally, a straightforward measurement of the Li(+) compensation depth is shown to yield estimates of the vacancy-related defect concentration in p-type FZ crystals.

[Observation on the clinical efficacy of shoulder pain in post-stroke shoulder-hand syndrome treated with floating acupuncture and rehabilitation training].

PubMed

Wang, Jun; Cui, Xiao; Ni, Huan-Huan; Huang, Chun-Shui; Zhou, Cui-Xia; Wu, Ji; Shi, Jun-Chao; Wu, Yi

2013-04-01

To compare the efficacy difference in the treatment of shoulder pain in post-stroke shoulder-hand syndrome among floating acupuncture, oral administration of western medicine and local fumigation of Chinese herbs. Ninety cases of post-stroke shoulder-hand syndrome (stage I) were randomized into a floating acupuncture group, a western medicine group and a local Chinese herbs fumigation group, 30 cases in each one. In the floating acupuncture group, two obvious tender points were detected on the shoulder and the site 80-100 mm inferior to each tender point was taken as the inserting point and stimulated with floating needling technique. In the western medicine group, mobic 7.5 mg was prescribed for oral administration. In the local Chinese herbs fumigation group, the formula for activating blood circulation and relaxing tendon was used for local fumigation. All the patients in three groups received rehabilitation training. The floating acupuncture, oral administration of western medicine, local Chinese herbs fumigation and rehabilitation training were given once a day respectively in corresponding group and the cases were observed for 1 month. The visual analogue scale (VAS) and Takagishi shoulder joint function assessment were adopted to evaluate the dynamic change of the patients with shoulder pain before and after treatment in three groups. The modified Barthel index was used to evaluate the dynamic change of daily life activity of the patients in three groups. With floating acupuncture, shoulder pain was relieved and the daily life activity was improved in the patients with post-stroke shoulder-hand syndrome, which was superior to the oral administration of western medicine and local Chinese herbs fumigation (P < 0.01). With local Chinese herbs fumigation, the improvement of shoulder pain was superior to the oral administration of western medicine. The difference in the improvement of daily life activity was not significant statistically between the local Chinese herbs fumigation and oral administration of western medicine, the efficacy was similar between these two therapies (P > 0.05). The floating acupuncture relieves shoulder pain of the patients with post-stroke shoulder-hand syndrome promptly and effectively, and the effects on shoulder pain and the improvements of daily life activity are superior to that of the oral administration of western medicine and local Chinese herbs fumigation.

Minimization of the environmental impact of chrome tanning: a new process with high chrome exhaustion.

PubMed

Morera, Josep M; Bacardit, Anna; Ollé, Lluís; Bartolí, Esther; Borràs, Maria D

2007-11-01

In all tanning technology operations wastes are generated. These reach the environment as residual waters, solid and liquid waste as well as atmospheric emissions and odours. This study tests an alternative method to the traditional tanning method at an industrial level. The new method is based on tanning without float and by significantly increasing the temperature at the end of the tanning process. The properties of the leathers obtained using the two methods have been compared and the results indicate that those leathers have similar physical, chemical, and organoleptic properties. However, the differences existing from the environmental point of view are significant. It is not necessary to use clean water for this tanning. Moreover, there is a 75% reduction of the residual float, a 91% reduction of the chrome discharged, and a 94% reduction of the chlorides discharged. A financial assessment was carried out to demonstrate that the newly proposed system is 32% more economic than the traditional one.

Expert Systems on Multiprocessor Architectures. Volume 4. Technical Reports

DTIC Science & Technology

1991-06-01

Floated-Current-Time0 -> The time that this function is called in user time uflts, expressed as a floating point number. Halt- Poligono Arrests the...default a statistics file will be printed out, if it can be. To prevent this make No-Statistics true. Unhalt- Poligono Unarrests the process in which the

76 FR 19290 - Safety Zone; Commencement Bay, Tacoma, WA

Federal Register 2010, 2011, 2012, 2013, 2014

2011-04-07

... the following points Latitude 47[deg]17'38'' N, Longitude 122[deg]28'43'' W; thence south easterly to... protruding from the shoreline along Ruston Way. Floating markers will be placed by the sponsor of the event... rectangle protruding from the shoreline along Ruston Way. Floating markers will be placed by the sponsor of...

40 CFR 63.685 - Standards: Tanks.

Code of Federal Regulations, 2010 CFR

2010-07-01

... in paragraph (c)(2)(i) of this section when a tank is used as an interim transfer point to transfer... fixed-roof tank equipped with an internal floating roof in accordance with the requirements specified in paragraph (e) of this section; (2) A tank equipped with an external floating roof in accordance with the...

Oil/gas collector/separator for underwater oil leaks

DOEpatents

Henning, Carl D.

1993-01-01

An oil/gas collector/separator for recovery of oil leaking, for example, from an offshore or underwater oil well. The separator is floated over the point of the leak and tethered in place so as to receive oil/gas floating, or forced under pressure, toward the water surface from either a broken or leaking oil well casing, line, or sunken ship. The separator is provided with a downwardly extending skirt to contain the oil/gas which floats or is forced upward into a dome wherein the gas is separated from the oil/water, with the gas being flared (burned) at the top of the dome, and the oil is separated from water and pumped to a point of use. Since the density of oil is less than that of water it can be easily separated from any water entering the dome.

Optimized stereo matching in binocular three-dimensional measurement system using structured light.

PubMed

Liu, Kun; Zhou, Changhe; Wei, Shengbin; Wang, Shaoqing; Fan, Xin; Ma, Jianyong

2014-09-10

In this paper, we develop an optimized stereo-matching method used in an active binocular three-dimensional measurement system. A traditional dense stereo-matching algorithm is time consuming due to a long search range and the high complexity of a similarity evaluation. We project a binary fringe pattern in combination with a series of N binary band limited patterns. In order to prune the search range, we execute an initial matching before exhaustive matching and evaluate a similarity measure using logical comparison instead of a complicated floating-point operation. Finally, an accurate point cloud can be obtained by triangulation methods and subpixel interpolation. The experiment results verify the computational efficiency and matching accuracy of the method.

Evaluation of floating-point sum or difference of products in carry-save domain

NASA Technical Reports Server (NTRS)

Wahab, A.; Erdogan, S.; Premkumar, A. B.

1992-01-01

An architecture to evaluate a 24-bit floating-point sum or difference of products using modified sequential carry-save multipliers with extensive pipelining is described. The basic building block of the architecture is a carry-save multiplier with built-in mantissa alignment for the summation during the multiplication cycles. A carry-save adder, capable of mantissa alignment, correctly positions products with the current carry-save sum. Carry propagation in individual multipliers is avoided and is only required once to produce the final result.

Floating-point scaling technique for sources separation automatic gain control

NASA Astrophysics Data System (ADS)

Fermas, A.; Belouchrani, A.; Ait-Mohamed, O.

2012-07-01

Based on the floating-point representation and taking advantage of scaling factor indetermination in blind source separation (BSS) processing, we propose a scaling technique applied to the separation matrix, to avoid the saturation or the weakness in the recovered source signals. This technique performs an automatic gain control in an on-line BSS environment. We demonstrate the effectiveness of this technique by using the implementation of a division-free BSS algorithm with two inputs, two outputs. The proposed technique is computationally cheaper and efficient for a hardware implementation compared to the Euclidean normalisation.

Paranoia.Ada: Sample output reports

NASA Technical Reports Server (NTRS)

1986-01-01

Paranoia.Ada is a program to diagnose floating point arithmetic in the context of the Ada programming language. The program evaluates the quality of a floating point arithmetic implementation with respect to the proposed IEEE Standards P754 and P854. Paranoia.Ada is derived from the original BASIC programming language version of Paranoia. The Paranoia.Ada replicates in Ada the test algorithms originally implemented in BASIC and adheres to the evaluation criteria established by W. M. Kahan. Paranoia.Ada incorporates a major structural redesign and employs applicable Ada architectural and stylistic features.

Collision Visualization of a Laser-Scanned Point Cloud of Streets and a Festival Float Model Used for the Revival of a Traditional Procession Route

NASA Astrophysics Data System (ADS)

Li, W.; Shigeta, K.; Hasegawa, K.; Li, L.; Yano, K.; Tanaka, S.

2017-09-01

Recently, laser-scanning technology, especially mobile mapping systems (MMSs), has been applied to measure 3D urban scenes. Thus, it has become possible to simulate a traditional cultural event in a virtual space constructed using measured point clouds. In this paper, we take the festival float procession in the Gion Festival that has a long history in Kyoto City, Japan. The city government plans to revive the original procession route that is narrow and not used at present. For the revival, it is important to know whether a festival float collides with houses, billboards, electric wires or other objects along the original route. Therefore, in this paper, we propose a method for visualizing the collisions of point cloud objects. The advantageous features of our method are (1) a see-through visualization with a correct depth feel that is helpful to robustly determine the collision areas, (2) the ability to visualize areas of high collision risk as well as real collision areas, and (3) the ability to highlight target visualized areas by increasing the point densities there.

Performance of a Space-Based Wavelet Compressor for Plasma Count Data on the MMS Fast Plasma Investigation

NASA Technical Reports Server (NTRS)

Barrie, A. C.; Smith, S. E.; Dorelli, J. C.; Gershman, D. J.; Yeh, P.; Schiff, C.; Avanov, L. A.

2017-01-01

Data compression has been a staple of imaging instruments for years. Recently, plasma measurements have utilized compression with relatively low compression ratios. The Fast Plasma Investigation (FPI) on board the Magnetospheric Multiscale (MMS) mission generates data roughly 100 times faster than previous plasma instruments, requiring a higher compression ratio to fit within the telemetry allocation. This study investigates the performance of a space-based compression standard employing a Discrete Wavelet Transform and a Bit Plane Encoder (DWT/BPE) in compressing FPI plasma count data. Data from the first 6 months of FPI operation are analyzed to explore the error modes evident in the data and how to adapt to them. While approximately half of the Dual Electron Spectrometer (DES) maps had some level of loss, it was found that there is little effect on the plasma moments and that errors present in individual sky maps are typically minor. The majority of Dual Ion Spectrometer burst sky maps compressed in a lossless fashion, with no error introduced during compression. Because of induced compression error, the size limit for DES burst images has been increased for Phase 1B. Additionally, it was found that the floating point compression mode yielded better results when images have significant compression error, leading to floating point mode being used for the fast survey mode of operation for Phase 1B. Despite the suggested tweaks, it was found that wavelet-based compression, and a DWT/BPE algorithm in particular, is highly suitable to data compression for plasma measurement instruments and can be recommended for future missions.

"Sinkers" and "Floaters."

ERIC Educational Resources Information Center

Leyden, Michael B.

1996-01-01

Describes a science experiment that gives students experiences with the float-sink phenomena and allows them to practice what Piaget called formal operational thinking. The goal of the experiment is to determine some of the variables responsible for cans of soda sinking or floating. (TJQ)

Does size and buoyancy affect the long-distance transport of floating debris?

NASA Astrophysics Data System (ADS)

Ryan, Peter G.

2015-08-01

Floating persistent debris, primarily made from plastic, disperses long distances from source areas and accumulates in oceanic gyres. However, biofouling can increase the density of debris items to the point where they sink. Buoyancy is related to item volume, whereas fouling is related to surface area, so small items (which have high surface area to volume ratios) should start to sink sooner than large items. Empirical observations off South Africa support this prediction: moving offshore from coastal source areas there is an increase in the size of floating debris, an increase in the proportion of highly buoyant items (e.g. sealed bottles, floats and foamed plastics), and a decrease in the proportion of thin items such as plastic bags and flexible packaging which have high surface area to volume ratios. Size-specific sedimentation rates may be one reason for the apparent paucity of small plastic items floating in the world’s oceans.

Integrated use of spatial and semantic relationships for extracting road networks from floating car data

NASA Astrophysics Data System (ADS)

Li, Jun; Qin, Qiming; Xie, Chao; Zhao, Yue

2012-10-01

The update frequency of digital road maps influences the quality of road-dependent services. However, digital road maps surveyed by probe vehicles or extracted from remotely sensed images still have a long updating circle and their cost remain high. With GPS technology and wireless communication technology maturing and their cost decreasing, floating car technology has been used in traffic monitoring and management, and the dynamic positioning data from floating cars become a new data source for updating road maps. In this paper, we aim to update digital road maps using the floating car data from China's National Commercial Vehicle Monitoring Platform, and present an incremental road network extraction method suitable for the platform's GPS data whose sampling frequency is low and which cover a large area. Based on both spatial and semantic relationships between a trajectory point and its associated road segment, the method classifies each trajectory point, and then merges every trajectory point into the candidate road network through the adding or modifying process according to its type. The road network is gradually updated until all trajectories have been processed. Finally, this method is applied in the updating process of major roads in North China and the experimental results reveal that it can accurately derive geometric information of roads under various scenes. This paper provides a highly-efficient, low-cost approach to update digital road maps.

33 CFR 162.130 - Connecting waters from Lake Huron to Lake Erie; general rules.

Code of Federal Regulations, 2010 CFR

2010-07-01

... vessel astern, alongside, or by pushing ahead; and (iii) Each dredge and floating plant. (4) The traffic... towing another vessel astern, alongside or by pushing ahead; and (iv) Each dredge and floating plant. (c... Captain of the Port of Detroit, Michigan. Detroit River means the connecting waters from Windmill Point...

75 FR 69034 - United States Navy Restricted Area, Menominee River, Marinette Marine Corporation Shipyard...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-11-10

...]37[min]10.0[sec] W; thence easterly along the Marinette Marine Corporation pier to the point of origin. The restricted area will be marked by a lighted and signed floating boat barrier. (b) The... floating boat barrier without permission from the United States Navy, Supervisor of Shipbuilding Gulf Coast...

76 FR 30024 - United States Navy Restricted Area, Menominee River, Marinette Marine Corporation Shipyard...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-05-24

... changed so that the restricted area could be marked with a signed floating buoy line instead of a signed floating barrier. That change has been made to the final rule. Procedural Requirements a. Review Under...; thence easterly along the Marinette Marine Corporation pier to the point of origin. The restricted area...

Overview of the DART project

DOE Office of Scientific and Technical Information (OSTI.GOV)

Berry, K.R.; Hansen, F.R.; Napolitano, L.M.

1992-01-01

DART (DSP Arrary for Reconfigurable Tasks) is a parallel architecture of two high-performance SDP (digital signal processing) chips with the flexibility to handle a wide range of real-time applications. Each of the 32-bit floating-point DSP processes in DART is programmable in a high-level languate ( C'' or Ada). We have added extensions to the real-time operating system used by DART in order to support parallel processor. The combination of high-level language programmability, a real-time operating system, and parallel processing support significantly reduces the development cost of application software for signal processing and control applications. We have demonstrated this capability bymore » using DART to reconstruct images in the prototype VIP (Video Imaging Projectile) groundstation.« less

Overview of the DART project

DOE Office of Scientific and Technical Information (OSTI.GOV)

Berry, K.R.; Hansen, F.R.; Napolitano, L.M.

1992-01-01

DART (DSP Arrary for Reconfigurable Tasks) is a parallel architecture of two high-performance SDP (digital signal processing) chips with the flexibility to handle a wide range of real-time applications. Each of the 32-bit floating-point DSP processes in DART is programmable in a high-level languate (``C`` or Ada). We have added extensions to the real-time operating system used by DART in order to support parallel processor. The combination of high-level language programmability, a real-time operating system, and parallel processing support significantly reduces the development cost of application software for signal processing and control applications. We have demonstrated this capability by usingmore » DART to reconstruct images in the prototype VIP (Video Imaging Projectile) groundstation.« less

High-performance floating-point image computing workstation for medical applications

NASA Astrophysics Data System (ADS)

Mills, Karl S.; Wong, Gilman K.; Kim, Yongmin

1990-07-01

The medical imaging field relies increasingly on imaging and graphics techniques in diverse applications with needs similar to (or more stringent than) those of the military, industrial and scientific communities. However, most image processing and graphics systems available for use in medical imaging today are either expensive, specialized, or in most cases both. High performance imaging and graphics workstations which can provide real-time results for a number of applications, while maintaining affordability and flexibility, can facilitate the application of digital image computing techniques in many different areas. This paper describes the hardware and software architecture of a medium-cost floating-point image processing and display subsystem for the NeXT computer, and its applications as a medical imaging workstation. Medical imaging applications of the workstation include use in a Picture Archiving and Communications System (PACS), in multimodal image processing and 3-D graphics workstation for a broad range of imaging modalities, and as an electronic alternator utilizing its multiple monitor display capability and large and fast frame buffer. The subsystem provides a 2048 x 2048 x 32-bit frame buffer (16 Mbytes of image storage) and supports both 8-bit gray scale and 32-bit true color images. When used to display 8-bit gray scale images, up to four different 256-color palettes may be used for each of four 2K x 2K x 8-bit image frames. Three of these image frames can be used simultaneously to provide pixel selectable region of interest display. A 1280 x 1024 pixel screen with 1: 1 aspect ratio can be windowed into the frame buffer for display of any portion of the processed image or images. In addition, the system provides hardware support for integer zoom and an 82-color cursor. This subsystem is implemented on an add-in board occupying a single slot in the NeXT computer. Up to three boards may be added to the NeXT for multiple display capability (e.g., three 1280 x 1024 monitors, each with a 16-Mbyte frame buffer). Each add-in board provides an expansion connector to which an optional image computing coprocessor board may be added. Each coprocessor board supports up to four processors for a peak performance of 160 MFLOPS. The coprocessors can execute programs from external high-speed microcode memory as well as built-in internal microcode routines. The internal microcode routines provide support for 2-D and 3-D graphics operations, matrix and vector arithmetic, and image processing in integer, IEEE single-precision floating point, or IEEE double-precision floating point. In addition to providing a library of C functions which links the NeXT computer to the add-in board and supports its various operational modes, algorithms and medical imaging application programs are being developed and implemented for image display and enhancement. As an extension to the built-in algorithms of the coprocessors, 2-D Fast Fourier Transform (FF1), 2-D Inverse FFF, convolution, warping and other algorithms (e.g., Discrete Cosine Transform) which exploit the parallel architecture of the coprocessor board are being implemented.

Sellers floats, meditation style, in the MDK on STS-121 / Expedition 13 joint operations

NASA Image and Video Library

2006-07-08

S121-E-06123 (8 July 2006) --- Astronaut Piers J. Sellers, STS-121 mission specialist, smiles for the camera as he floats on the middeck of the Space Shuttle Discovery while docked with the International Space Station.

A Floating Cylinder on an Unbounded Bath

NASA Astrophysics Data System (ADS)

Chen, Hanzhe; Siegel, David

2018-03-01

In this paper, we reconsider a circular cylinder horizontally floating on an unbounded reservoir in a gravitational field directed downwards, which was studied by Bhatnagar and Finn (Phys Fluids 18(4):047103, 2006). We follow their approach but with some modifications. We establish the relation between the total energy E_T relative to the undisturbed state and the total force F_T , that is, F_T = -dE_T/dh , where h is the height of the center of the cylinder relative to the undisturbed fluid level. There is a monotone relation between h and the wetting angle φ _0 . We study the number of equilibria, the floating configurations and their stability for all parameter values. We find that the system admits at most two equilibrium points for arbitrary contact angle γ , the one with smaller φ _0 is stable and the one with larger φ _0 is unstable. Since the one-sided solution can be translated horizontally, the fluid interfaces may intersect. We show that the stable equilibrium point never lies in the intersection region, while the unstable equilibrium point may lie in the intersection region.

Floating Potential Probe Langmuir Probe Data Reduction Results

NASA Technical Reports Server (NTRS)

Morton, Thomas L.; Minow, Joseph I.

2002-01-01

During its first five months of operations, the Langmuir Probe on the Floating Potential Probe (FPP) obtained data on ionospheric electron densities and temperatures in the ISS orbit. In this paper, the algorithms for data reduction are presented, and comparisons are made of FPP data with ground-based ionosonde and Incoherent Scattering Radar (ISR) results. Implications for ISS operations are detailed, and the need for a permanent FPP on ISS is examined.

76 FR 2254 - Notice of Arrival on the Outer Continental Shelf

Federal Register 2010, 2011, 2012, 2013, 2014

2011-01-13

... of arrival for floating facilities, mobile offshore drilling units (MODUs), and vessels planning to... Ship Security Certificate. MMS Minerals Management Service. MODU Mobile Offshore Drilling Unit. NAICS... rule outlines the procedures that owners or operators of floating facilities, mobile offshore drilling...

Integer cosine transform for image compression

NASA Technical Reports Server (NTRS)

Cheung, K.-M.; Pollara, F.; Shahshahani, M.

1991-01-01

This article describes a recently introduced transform algorithm called the integer cosine transform (ICT), which is used in transform-based data compression schemes. The ICT algorithm requires only integer operations on small integers and at the same time gives a rate-distortion performance comparable to that offered by the floating-point discrete cosine transform (DCT). The article addresses the issue of implementation complexity, which is of prime concern for source coding applications of interest in deep-space communications. Complexity reduction in the transform stage of the compression scheme is particularly relevant, since this stage accounts for most (typically over 80 percent) of the computational load.

A Scalable Architecture of a Structured LDPC Decoder

NASA Technical Reports Server (NTRS)

Lee, Jason Kwok-San; Lee, Benjamin; Thorpe, Jeremy; Andrews, Kenneth; Dolinar, Sam; Hamkins, Jon

2004-01-01

We present a scalable decoding architecture for a certain class of structured LDPC codes. The codes are designed using a small (n,r) protograph that is replicated Z times to produce a decoding graph for a (Z x n, Z x r) code. Using this architecture, we have implemented a decoder for a (4096,2048) LDPC code on a Xilinx Virtex-II 2000 FPGA, and achieved decoding speeds of 31 Mbps with 10 fixed iterations. The implemented message-passing algorithm uses an optimized 3-bit non-uniform quantizer that operates with 0.2dB implementation loss relative to a floating point decoder.

Applications considerations in the system design of highly concurrent multiprocessors

NASA Technical Reports Server (NTRS)

Lundstrom, Stephen F.

1987-01-01

A flow model processor approach to parallel processing is described, using very-high-performance individual processors, high-speed circuit switched interconnection networks, and a high-speed synchronization capability to minimize the effect of the inherently serial portions of applications on performance. Design studies related to the determination of the number of processors, the memory organization, and the structure of the networks used to interconnect the processor and memory resources are discussed. Simulations indicate that applications centered on the large shared data memory should be able to sustain over 500 million floating point operations per second.

A test data compression scheme based on irrational numbers stored coding.

PubMed

Wu, Hai-feng; Cheng, Yu-sheng; Zhan, Wen-fa; Cheng, Yi-fei; Wu, Qiong; Zhu, Shi-juan

2014-01-01

Test question has already become an important factor to restrict the development of integrated circuit industry. A new test data compression scheme, namely irrational numbers stored (INS), is presented. To achieve the goal of compress test data efficiently, test data is converted into floating-point numbers, stored in the form of irrational numbers. The algorithm of converting floating-point number to irrational number precisely is given. Experimental results for some ISCAS 89 benchmarks show that the compression effect of proposed scheme is better than the coding methods such as FDR, AARLC, INDC, FAVLC, and VRL.

26 CFR 1.1274-2 - Issue price of debt instruments to which section 1274 applies.

Code of Federal Regulations, 2010 CFR

2010-04-01

...- borrower to the seller-lender that is designated as interest or points. See Example 2 of § 1.1273-2(g)(5... ignored. (f) Treatment of variable rate debt instruments—(1) Stated interest at a qualified floating rate... qualified floating rate (or rates) is determined by assuming that the instrument provides for a fixed rate...

Modeling of subaqueous melting in Petermann Fjord, Northwestern Greenland using an ocean general circulation model

NASA Astrophysics Data System (ADS)

Cai, C.; Rignot, E. J.; Xu, Y.; An, L.; Tinto, K. J.; van den Broeke, M. R.

2014-12-01

Basal melting of the floating tongue of Petermann Glacier, in northwestern Greenland is by far the largest process of mass ablation. Melting of the floating tongue is controlled by the buoyancy of the melt water plume, the pressure-dependence of the melting point of sea ice, and the mixing of warm subsurface water with fresh buoyant subglacial discharge. In prior simulations of this melting process, the role of subglacial discharge has been neglected because in similar configurations (floating ice shelves) in the Antarctic, surface runoff is negligible; this is however not true in Greenland. Here, we use the Mass Institute of Technology general circulation model (MITgcm) at a high spatial resolution (10 m x 10 m) to simulate the melting process of the ice shelf in 2-D. The model is constrained by ice shelf bathymetry and ice thickness (refined model in the immediate vicinity of the grounding line) from NASA Operation IceBridge (2011), ocean temperature/salinity data from Johnson et al. (2011), ocean tide height and current from the Arctic Ocean Tidal Inverse Model (AOTIM-5) by Padman and Erofeeva (2004) and subglacial discharge at the grounding line calculated by the hydrostatic potential of the ice from estimated products of the Regional Atmospheric Climate Model (RACMO) of Royal Netherlands Meteorological Institute (KNMI). We compare the results obtained in winter (no runoff) with summer, and the sensitivity of the results to thermal forcing from the ocean, and to the variation of tide height and current, and to the magnitude of subglacial runoff. We conclude on the impact of the ocean and surface melting on the melting regime of the floating ice tongue of Petermann. The basal melt rate increases ~20% with summer surface runoff. This work is performed under a contract with NASA Cryosphere Program.

A floating-point digital receiver for MRI.

PubMed

Hoenninger, John C; Crooks, Lawrence E; Arakawa, Mitsuaki

2002-07-01

A magnetic resonance imaging (MRI) system requires the highest possible signal fidelity and stability for clinical applications. Quadrature analog receivers have problems with channel matching, dc offset and analog-to-digital linearity. Fixed-point digital receivers (DRs) reduce all of these problems. We have demonstrated that a floating-point DR using large (order 124 to 512) FIR low-pass filters also overcomes these problems, automatically provides long word length and has low latency between signals. A preloaded table of finite impuls response (FIR) filter coefficients provides fast switching between one of 129 different one-stage and two-stage multrate FIR low-pass filters with bandwidths between 4 KHz and 125 KHz. This design has been implemented on a dual channel circuit board for a commercial MRI system.

Gastroretentive extended-release floating granules prepared using a novel fluidized hot melt granulation (FHMG) technique.

PubMed

Zhai, H; Jones, D S; McCoy, C P; Madi, A M; Tian, Y; Andrews, G P

2014-10-06

The objective of this work was to investigate the feasibility of using a novel granulation technique, namely, fluidized hot melt granulation (FHMG), to prepare gastroretentive extended-release floating granules. In this study we have utilized FHMG, a solvent free process in which granulation is achieved with the aid of low melting point materials, using Compritol 888 ATO and Gelucire 50/13 as meltable binders, in place of conventional liquid binders. The physicochemical properties, morphology, floating properties, and drug release of the manufactured granules were investigated. Granules prepared by this method were spherical in shape and showed good flowability. The floating granules exhibited sustained release exceeding 10 h. Granule buoyancy (floating time and strength) and drug release properties were significantly influenced by formulation variables such as excipient type and concentration, and the physical characteristics (particle size, hydrophilicity) of the excipients. Drug release rate was increased by increasing the concentration of hydroxypropyl cellulose (HPC) and Gelucire 50/13, or by decreasing the particle size of HPC. Floating strength was improved through the incorporation of sodium bicarbonate and citric acid. Furthermore, floating strength was influenced by the concentration of HPC within the formulation. Granules prepared in this way show good physical characteristics, floating ability, and drug release properties when placed in simulated gastric fluid. Moreover, the drug release and floating properties can be controlled by modification of the ratio or physical characteristics of the excipients used in the formulation.

26 CFR 1.483-2 - Unstated interest.

Code of Federal Regulations, 2010 CFR

2010-04-01

... percentage points above the yield on 6-month Treasury bills at the mid-point of the semiannual period immediately preceding each interest payment date. Assume that the interest rate is a qualified floating rate...

[The validation of the effect of correcting spectral background changes based on floating reference method by simulation].

PubMed

Wang, Zhu-lou; Zhang, Wan-jie; Li, Chen-xi; Chen, Wen-liang; Xu, Ke-xin

2015-02-01

There are some challenges in near-infrared non-invasive blood glucose measurement, such as the low signal to noise ratio of instrument, the unstable measurement conditions, the unpredictable and irregular changes of the measured object, and etc. Therefore, it is difficult to extract the information of blood glucose concentrations from the complicated signals accurately. Reference measurement method is usually considered to be used to eliminate the effect of background changes. But there is no reference substance which changes synchronously with the anylate. After many years of research, our research group has proposed the floating reference method, which is succeeded in eliminating the spectral effects induced by the instrument drifts and the measured object's background variations. But our studies indicate that the reference-point will changes following the changing of measurement location and wavelength. Therefore, the effects of floating reference method should be verified comprehensively. In this paper, keeping things simple, the Monte Carlo simulation employing Intralipid solution with the concentrations of 5% and 10% is performed to verify the effect of floating reference method used into eliminating the consequences of the light source drift. And the light source drift is introduced through varying the incident photon number. The effectiveness of the floating reference method with corresponding reference-points at different wavelengths in eliminating the variations of the light source drift is estimated. The comparison of the prediction abilities of the calibration models with and without using this method shows that the RMSEPs of the method are decreased by about 98.57% (5%Intralipid)and 99.36% (10% Intralipid)for different Intralipid. The results indicate that the floating reference method has obvious effect in eliminating the background changes.

32 CFR 736.5 - Disposition of real and personal property under special statutory authority.

Code of Federal Regulations, 2011 CFR

2011-07-01

... of Naval Operations, applications for boats to the Naval Sea Systems Command, and applications for barges, floating drydocks, and other floating construction equipment to the Naval Facilities Engineering... Disposition Manual. (g) Disposition of equipment for research. Under the act of September 6, 1958 (72 Stat...

A simple combined floating and anchored collagen gel for enhancing mechanical strength of culture system.

PubMed

Harada, Ichiro; Kim, Sung-Gon; Cho, Chong Su; Kurosawa, Hisashi; Akaike, Toshihiro

2007-01-01

In this study, a simple combined method consisting of floating and anchored collagen gel in a ligament or tendon equivalent culture system was used to produce the oriented fibrils in fibroblast-populated collagen matrices (FPCMs) during the remodeling and contraction of the collagen gel. Orientation of the collagen fibrils along single axis occurred over the whole area of the floating section and most of the fibroblasts were elongated and aligned along the oriented collagen fibrils, whereas no significant orientation of fibrils was observed in normally contracted FPCMs by the floating method. Higher elasticity and enhanced mechanical strength were obtained using our simple method compared with normally contracted floating FPCMs. The Young's modulus and the breaking point of the FPCMs were dependent on the initial cell densities. This simple method will be applied as a convenient bioreactor to study cellular processes of the fibroblasts in the tissues with highly oriented fibrils such as ligaments or tendons. (c) 2006 Wiley Periodicals, Inc.

Floating sample-collection platform with stage-activated automatic water sampler for streams with large variation in stage

USGS Publications Warehouse

Tarte, Stephen R.; Schmidt, A.R.; Sullivan, Daniel J.

1992-01-01

A floating sample-collection platform is described for stream sites where the vertical or horizontal distance between the stream-sampling point and a safe location for the sampler exceed the suction head of the sampler. The platform allows continuous water sampling over the entire storm-runoff hydrogrpah. The platform was developed for a site in southern Illinois.

Floating assembly of diatom Coscinodiscus sp. microshells.

PubMed

Wang, Yu; Pan, Junfeng; Cai, Jun; Zhang, Deyuan

2012-03-30

Diatoms have silica frustules with transparent and delicate micro/nano scale structures, two dimensional pore arrays, and large surface areas. Although, the diatom cells of Coscinodiscus sp. live underwater, we found that their valves can float on water and assemble together. Experiments show that the convex shape and the 40 nm sieve pores of the valves allow them to float on water, and that the buoyancy and the micro-range attractive forces cause the valves to assemble together at the highest point of water. As measured by AFM calibrated glass needles fixed in manipulator, the buoyancy force on a single floating valve may reach up to 10 μN in water. Turning the valves over, enlarging the sieve pores, reducing the surface tension of water, or vacuum pumping may cause the floating valves to sink. After the water has evaporated, the floating valves remained in their assembled state and formed a monolayer film. The bonded diatom monolayer may be valuable in studies on diatom based optical devices, biosensors, solar cells, and batteries, to better use the optical and adsorption properties of frustules. The floating assembly phenomenon can also be used as a self-assembly method for fabricating monolayer of circular plates. Copyright © 2012 Elsevier Inc. All rights reserved.

Quality of life associated with perceived stigma and discrimination among the floating population in Shanghai, China: a qualitative study.

PubMed

Wang, Ji-Wei; Cui, Zhi-Ting; Cui, Hong-Wei; Wei, Chang-Nian; Harada, Koichi; Minamoto, Keiko; Ueda, Kimiyo; Ingle, Kapilkumar N; Zhang, Cheng-Gang; Ueda, Atsushi

2010-12-01

The floating population refers to the large and increasing number of migrants without local household registration status and has become a new demographic phenomenon in China. Most of these migrants move from the rural areas of the central and western parts of China to the eastern and coastal metropolitan areas in pursuit of a better life. The floating population of China was composed of 121 million people in 2000, and this number was expected to increase to 300 million by 2010. Quality of life (QOL) studies of the floating population could provide a critical starting point for recognizing the potential of regions, cities and local communities to improve QOL. This study explored the construct of QOL of the floating population in Shanghai, China. We conducted eight focus groups with 58 members of the floating population (24 males and 34 females) and then performed a qualitative thematic analysis of the interviews. The following five QOL domains were identified from the analysis: personal development, jobs and career, family life, social relationships and social security. The results indicated that stigma and discrimination permeate these life domains and influence the framing of life expectations. Proposals were made for reducing stigma and discrimination against the floating population to improve the QOL of this population.

FLOAT OPERATED RADIAL GATE INSTALLATION. WASTEWAY NO. 1. WELLTONMOHAWK CANAL ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

FLOAT OPERATED RADIAL GATE INSTALLATION. WASTEWAY NO. 1. WELLTON-MOHAWK CANAL - STA. 99+23.50. United States Department of the Interior, Bureau of Reclamation; Gila Project, Arizona, Wellton-Mohawk Division. Drawing No. 50-D-2497, dated March 8, 1949, Denver Colorado. Sheet 1 of 7 - Wellton-Mohawk Irrigation System, Wasteway No. 1, Wellton-Mohawk Canal, North side of Wellton-Mohawk Canal, bounded by Gila River to North & the Union Pacific Railroad & Gila Mountains to south, Wellton, Yuma County, AZ

FLOAT OPERATED RADIAL GATE HOIST ASSEMBLY LIST OF PARTS ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

FLOAT OPERATED RADIAL GATE HOIST ASSEMBLY - LIST OF PARTS - BASE-CRANK. WASTEWAY NO. 1. WELLTON-MOHAWK CANAL - STA. 99+23.50. United States Department of the Interior, Bureau of Reclamation; Gila Project, Arizona, Wellton-Mohawk Division. Drawing No. 50-D-2511, dated May 3, 1949, Denver Colorado. Sheet 1 of 2 - Wellton-Mohawk Irrigation System, Wasteway No. 1, Wellton-Mohawk Canal, North side of Wellton-Mohawk Canal, bounded by Gila River to North & the Union Pacific Railroad & Gila Mountains to south, Wellton, Yuma County, AZ

Extending the BEAGLE library to a multi-FPGA platform

PubMed Central

2013-01-01

Background Maximum Likelihood (ML)-based phylogenetic inference using Felsenstein’s pruning algorithm is a standard method for estimating the evolutionary relationships amongst a set of species based on DNA sequence data, and is used in popular applications such as RAxML, PHYLIP, GARLI, BEAST, and MrBayes. The Phylogenetic Likelihood Function (PLF) and its associated scaling and normalization steps comprise the computational kernel for these tools. These computations are data intensive but contain fine grain parallelism that can be exploited by coprocessor architectures such as FPGAs and GPUs. A general purpose API called BEAGLE has recently been developed that includes optimized implementations of Felsenstein’s pruning algorithm for various data parallel architectures. In this paper, we extend the BEAGLE API to a multiple Field Programmable Gate Array (FPGA)-based platform called the Convey HC-1. Results The core calculation of our implementation, which includes both the phylogenetic likelihood function (PLF) and the tree likelihood calculation, has an arithmetic intensity of 130 floating-point operations per 64 bytes of I/O, or 2.03 ops/byte. Its performance can thus be calculated as a function of the host platform’s peak memory bandwidth and the implementation’s memory efficiency, as 2.03 × peak bandwidth × memory efficiency. Our FPGA-based platform has a peak bandwidth of 76.8 GB/s and our implementation achieves a memory efficiency of approximately 50%, which gives an average throughput of 78 Gflops. This represents a ~40X speedup when compared with BEAGLE’s CPU implementation on a dual Xeon 5520 and 3X speedup versus BEAGLE’s GPU implementation on a Tesla T10 GPU for very large data sizes. The power consumption is 92 W, yielding a power efficiency of 1.7 Gflops per Watt. Conclusions The use of data parallel architectures to achieve high performance for likelihood-based phylogenetic inference requires high memory bandwidth and a design methodology that emphasizes high memory efficiency. To achieve this objective, we integrated 32 pipelined processing elements (PEs) across four FPGAs. For the design of each PE, we developed a specialized synthesis tool to generate a floating-point pipeline with resource and throughput constraints to match the target platform. We have found that using low-latency floating-point operators can significantly reduce FPGA area and still meet timing requirement on the target platform. We found that this design methodology can achieve performance that exceeds that of a GPU-based coprocessor. PMID:23331707

A real-time hybrid neuron network for highly parallel cognitive systems.

PubMed

Christiaanse, Gerrit Jan; Zjajo, Amir; Galuzzi, Carlo; van Leuken, Rene

2016-08-01

For comprehensive understanding of how neurons communicate with each other, new tools need to be developed that can accurately mimic the behaviour of such neurons and neuron networks under `real-time' constraints. In this paper, we propose an easily customisable, highly pipelined, neuron network design, which executes optimally scheduled floating-point operations for maximal amount of biophysically plausible neurons per FPGA family type. To reduce the required amount of resources without adverse effect on the calculation latency, a single exponent instance is used for multiple neuron calculation operations. Experimental results indicate that the proposed network design allows the simulation of up to 1188 neurons on Virtex7 (XC7VX550T) device in brain real-time yielding a speed-up of x12.4 compared to the state-of-the art.

Failure detection in high-performance clusters and computers using chaotic map computations

DOEpatents

Rao, Nageswara S.

2015-09-01

A programmable media includes a processing unit capable of independent operation in a machine that is capable of executing 10.sup.18 floating point operations per second. The processing unit is in communication with a memory element and an interconnect that couples computing nodes. The programmable media includes a logical unit configured to execute arithmetic functions, comparative functions, and/or logical functions. The processing unit is configured to detect computing component failures, memory element failures and/or interconnect failures by executing programming threads that generate one or more chaotic map trajectories. The central processing unit or graphical processing unit is configured to detect a computing component failure, memory element failure and/or an interconnect failure through an automated comparison of signal trajectories generated by the chaotic maps.

A 2000-Hour Durability Test of a 5-Centimeter Diameter Mercury Bombardment Ion Thruster

NASA Technical Reports Server (NTRS)

Nakanishi, S.; Finke, R. G.

1972-01-01

A 2000-hour durability test of a modified Hughes SIT-5 (Structurally Integrated Thruster, 5 cm) was conducted at the Lewis Research Center. The thruster operated with a translating screen thrust vector grid locked in position for 10 deg beam deflection. The test was essentially continuous except for seven stoppages of beam current. The neutralizer keeper voltage and thruster floating potential increased slightly with time. Performance profiles and maps of thruster characteristics were obtained at 453 and 2023 hours into the test. Overall efficiency was nearly constant at 31 - 32 percent, and operating characteristics were similar at both points in the test. A post-shutdown inspection showed negligible erosion damage to the accelerator and cathode baffle. Some erosion was found in the aperture of the neutralizer cathode.

Fourier transform wavefront control with adaptive prediction of the atmosphere.

PubMed

Poyneer, Lisa A; Macintosh, Bruce A; Véran, Jean-Pierre

2007-09-01

Predictive Fourier control is a temporal power spectral density-based adaptive method for adaptive optics that predicts the atmosphere under the assumption of frozen flow. The predictive controller is based on Kalman filtering and a Fourier decomposition of atmospheric turbulence using the Fourier transform reconstructor. It provides a stable way to compensate for arbitrary numbers of atmospheric layers. For each Fourier mode, efficient and accurate algorithms estimate the necessary atmospheric parameters from closed-loop telemetry and determine the predictive filter, adjusting as conditions change. This prediction improves atmospheric rejection, leading to significant improvements in system performance. For a 48x48 actuator system operating at 2 kHz, five-layer prediction for all modes is achievable in under 2x10(9) floating-point operations/s.

An important atomic process in the CVD growth of graphene: Sinking and up-floating of carbon atom on copper surface

NASA Astrophysics Data System (ADS)

Li, Yingfeng; Li, Meicheng; Gu, TianSheng; Bai, Fan; Yu, Yue; Trevor, Mwenya; Yu, Yangxin

2013-11-01

By density functional theory (DFT) calculations, the early stages of the growth of graphene on copper (1 1 1) surface are investigated. At the very first time of graphene growth, the carbon atom sinks into subsurface. As more carbon atoms are adsorbed nearby the site, the sunken carbon atom will spontaneously form a dimer with one of the newly adsorbed carbon atoms, and the formed dimer will up-float on the top of the surface. We emphasize the role of the co-operative relaxation of the co-adsorbed carbon atoms in facilitating the sinking and up-floating of carbon atoms. In detail: when two carbon atoms are co-adsorbed, their co-operative relaxation will result in different carbon-copper interactions for the co-adsorbed carbon atoms. This difference facilitates the sinking of a single carbon atom into the subsurface. As a third carbon atom is co-adsorbed nearby, it draws the sunken carbon atom on top of the surface, forming a dimer. Co-operative relaxations of the surface involving all adsorbed carbon atoms and their copper neighbors facilitate these sinking and up-floating processes. This investigation is helpful for the deeper understanding of graphene synthesis and the choosing of optimal carbon sources or process.

Evaluation of accelerated iterative x-ray CT image reconstruction using floating point graphics hardware.

PubMed

Kole, J S; Beekman, F J

2006-02-21

Statistical reconstruction methods offer possibilities to improve image quality as compared with analytical methods, but current reconstruction times prohibit routine application in clinical and micro-CT. In particular, for cone-beam x-ray CT, the use of graphics hardware has been proposed to accelerate the forward and back-projection operations, in order to reduce reconstruction times. In the past, wide application of this texture hardware mapping approach was hampered owing to limited intrinsic accuracy. Recently, however, floating point precision has become available in the latest generation commodity graphics cards. In this paper, we utilize this feature to construct a graphics hardware accelerated version of the ordered subset convex reconstruction algorithm. The aims of this paper are (i) to study the impact of using graphics hardware acceleration for statistical reconstruction on the reconstructed image accuracy and (ii) to measure the speed increase one can obtain by using graphics hardware acceleration. We compare the unaccelerated algorithm with the graphics hardware accelerated version, and for the latter we consider two different interpolation techniques. A simulation study of a micro-CT scanner with a mathematical phantom shows that at almost preserved reconstructed image accuracy, speed-ups of a factor 40 to 222 can be achieved, compared with the unaccelerated algorithm, and depending on the phantom and detector sizes. Reconstruction from physical phantom data reconfirms the usability of the accelerated algorithm for practical cases.

Fast projection/backprojection and incremental methods applied to synchrotron light tomographic reconstruction.

PubMed

de Lima, Camila; Salomão Helou, Elias

2018-01-01

Iterative methods for tomographic image reconstruction have the computational cost of each iteration dominated by the computation of the (back)projection operator, which take roughly O(N 3 ) floating point operations (flops) for N × N pixels images. Furthermore, classical iterative algorithms may take too many iterations in order to achieve acceptable images, thereby making the use of these techniques unpractical for high-resolution images. Techniques have been developed in the literature in order to reduce the computational cost of the (back)projection operator to O(N 2 logN) flops. Also, incremental algorithms have been devised that reduce by an order of magnitude the number of iterations required to achieve acceptable images. The present paper introduces an incremental algorithm with a cost of O(N 2 logN) flops per iteration and applies it to the reconstruction of very large tomographic images obtained from synchrotron light illuminated data.

Determinant Computation on the GPU using the Condensation Method

NASA Astrophysics Data System (ADS)

Anisul Haque, Sardar; Moreno Maza, Marc

2012-02-01

We report on a GPU implementation of the condensation method designed by Abdelmalek Salem and Kouachi Said for computing the determinant of a matrix. We consider two types of coefficients: modular integers and floating point numbers. We evaluate the performance of our code by measuring its effective bandwidth and argue that it is numerical stable in the floating point number case. In addition, we compare our code with serial implementation of determinant computation from well-known mathematical packages. Our results suggest that a GPU implementation of the condensation method has a large potential for improving those packages in terms of running time and numerical stability.

Investigation of Springing Responses on the Great Lakes Ore Carrier M/V STEWART J. CORT

DTIC Science & Technology

1980-12-01

175k tons.6 Using these values one can write : JL@APBD - ACTflALIVIRTVAL (MALAST) (4.) BeALLAST &VAC TUAL U(L@ADN@) and 0.94 10 The shifting of theI’M...will have to write a routine to convert the floating-point num- bers into the other machine’s internal floating-point format. The CCI record is again...THE RESULTS AND WRITES W1l TO THE LINE PRINTER. C IT ALSO PUTS THE RESUL~rs IN A DISA FIL1E .C C WRITTEN BY JCD3 NOVEMBER 1970f C C C

A floating-point/multiple-precision processor for airborne applications

NASA Technical Reports Server (NTRS)

Yee, R.

1982-01-01

A compact input output (I/O) numerical processor capable of performing floating-point, multiple precision and other arithmetic functions at execution times which are at least 100 times faster than comparable software emulation is described. The I/O device is a microcomputer system containing a 16 bit microprocessor, a numerical coprocessor with eight 80 bit registers running at a 5 MHz clock rate, 18K random access memory (RAM) and 16K electrically programmable read only memory (EPROM). The processor acts as an intelligent slave to the host computer and can be programmed in high order languages such as FORTRAN and PL/M-86.

Optimal Compression Methods for Floating-point Format Images

NASA Technical Reports Server (NTRS)

Pence, W. D.; White, R. L.; Seaman, R.

2009-01-01

We report on the results of a comparison study of different techniques for compressing FITS images that have floating-point (real*4) pixel values. Standard file compression methods like GZIP are generally ineffective in this case (with compression ratios only in the range 1.2 - 1.6), so instead we use a technique of converting the floating-point values into quantized scaled integers which are compressed using the Rice algorithm. The compressed data stream is stored in FITS format using the tiled-image compression convention. This is technically a lossy compression method, since the pixel values are not exactly reproduced, however all the significant photometric and astrometric information content of the image can be preserved while still achieving file compression ratios in the range of 4 to 8. We also show that introducing dithering, or randomization, when assigning the quantized pixel-values can significantly improve the photometric and astrometric precision in the stellar images in the compressed file without adding additional noise. We quantify our results by comparing the stellar magnitudes and positions as measured in the original uncompressed image to those derived from the same image after applying successively greater amounts of compression.

An ACGME Duty Hour Compliant 3-Person Night Float System for Neurological Surgery Residency Programs.

PubMed

Ragel, Brian T; Piedra, Mark; Klimo, Paul; Burchiel, Kim J; Waldo, Heidi; McCartney, Shirley; Selden, Nathan R

2014-06-01

In 2003, the Accreditation Council for Graduate Medical Education (ACGME) instituted the 24+6-hour work schedule and 80-hour workweek, and in 2011, it enhanced work hour and supervision standards. In response, Oregon Health & Science University's (OHSU) neurological surgery residency instituted a 3-person night float system. We analyzed work hour records and operative experience for 1 year before and after night float implementation in a model that shortened a combined introductory research and basic clinical neurosciences rotation from 12 to 6 months. We analyzed residents' perception of the system using a confidential survey. The ACGME 2011 work hour standards were applied to both time periods. AFTER NIGHT FLOAT IMPLEMENTATION, THE NUMBER OF DUTY HOUR VIOLATIONS WAS REDUCED: 28-hour shift (11 versus 235), 8 hours off between shifts (2 versus 20), 80 hours per week (0 versus 17), and total violations (23 versus 275). Violations increased only for the less than 4 days off per 4-week interval rule (10 versus 3). No meaningful difference was seen in the number of operative cases performed per year at any postgraduate year (PGY) training level: PGY-2 (336 versus 351), PGY-3 (394 versus 354), PGY-4 (803 versus 802), PGY-5 (1075 versus 1040), PGY-7 (947 versus 913), and total (3555 versus 3460). Residents rated the new system favorably. To meet 2011 ACGME duty hour standards, the OHSU neurological surgery residency instituted a 3-person night float system. A nearly complete elimination of work hour violations did not affect overall resident operative experience.

Deflection of Resilient Materials for Reduction of Floor Impact Sound

PubMed Central

Lee, Jung-Yoon; Kim, Jong-Mun

2014-01-01

Recently, many residents living in apartment buildings in Korea have been bothered by noise coming from the houses above. In order to reduce noise pollution, communities are increasingly imposing bylaws, including the limitation of floor impact sound, minimum thickness of floors, and floor soundproofing solutions. This research effort focused specifically on the deflection of resilient materials in the floor sound insulation systems of apartment houses. The experimental program involved conducting twenty-seven material tests and ten sound insulation floating concrete floor specimens. Two main parameters were considered in the experimental investigation: the seven types of resilient materials and the location of the loading point. The structural behavior of sound insulation floor floating was predicted using the Winkler method. The experimental and analytical results indicated that the cracking strength of the floating concrete floor significantly increased with increasing the tangent modulus of resilient material. The deflection of the floating concrete floor loaded at the side of the specimen was much greater than that of the floating concrete floor loaded at the center of the specimen. The Winkler model considering the effect of modulus of resilient materials was able to accurately predict the cracking strength of the floating concrete floor. PMID:25574491

Deflection of resilient materials for reduction of floor impact sound.

PubMed

Lee, Jung-Yoon; Kim, Jong-Mun

2014-01-01

Recently, many residents living in apartment buildings in Korea have been bothered by noise coming from the houses above. In order to reduce noise pollution, communities are increasingly imposing bylaws, including the limitation of floor impact sound, minimum thickness of floors, and floor soundproofing solutions. This research effort focused specifically on the deflection of resilient materials in the floor sound insulation systems of apartment houses. The experimental program involved conducting twenty-seven material tests and ten sound insulation floating concrete floor specimens. Two main parameters were considered in the experimental investigation: the seven types of resilient materials and the location of the loading point. The structural behavior of sound insulation floor floating was predicted using the Winkler method. The experimental and analytical results indicated that the cracking strength of the floating concrete floor significantly increased with increasing the tangent modulus of resilient material. The deflection of the floating concrete floor loaded at the side of the specimen was much greater than that of the floating concrete floor loaded at the center of the specimen. The Winkler model considering the effect of modulus of resilient materials was able to accurately predict the cracking strength of the floating concrete floor.

77 FR 41685 - Drawbridge Operation Regulation; Willamette River, Portland, OR

Federal Register 2010, 2011, 2012, 2013, 2014

2012-07-16

... deviation is necessary to accommodate Portland's Big Float event. This deviation allows the bridge to remain... of the Big Float event. The Hawthorne Bridge crosses the Willamette River at mile 13.1 and provides 49 feet of vertical clearance above Columbia River Datum 0.0 while in the closed position. Vessels...

30 CFR 250.1911 - What criteria for hazards analyses must my SEMS program meet?

Code of Federal Regulations, 2011 CFR

2011-07-01

..., AND ENFORCEMENT, DEPARTMENT OF THE INTERIOR OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER... to the seabed (i.e., mobile offshore drilling units; floating production systems; floating production..., production, and transportation activities for oil, gas, or sulphur from areas leased in the OCS. Facilities...

30 CFR 250.1911 - What criteria for hazards analyses must my SEMS program meet?

Code of Federal Regulations, 2012 CFR

2012-07-01

..., DEPARTMENT OF THE INTERIOR OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Safety...., mobile offshore drilling units; floating production systems; floating production, storage and offloading... transportation activities for oil, gas, or sulphur from areas leased in the OCS. Facilities also include DOI...

Water temperature effects from simulated dam operations and structures in the Middle Fork Willamette River, western Oregon

USGS Publications Warehouse

Buccola, Norman L.; Turner, Daniel F.; Rounds, Stewart A.

2016-09-14

Significant FindingsStreamflow and water temperature in the Middle Fork Willamette River (MFWR), western Oregon, have been regulated and altered since the construction of Lookout Point, Dexter, and Hills Creek Dams in 1954 and 1961, respectively. Each year, summer releases from the dams typically are cooler than pre-dam conditions, with the reverse (warmer than pre-dam conditions) occurring in autumn. This pattern has been detrimental to habitat of endangered Upper Willamette River (UWR) Chinook salmon (Oncorhynchus tshawytscha) and UWR winter steelhead (O. mykiss) throughout multiple life stages. In this study, scenarios testing different dam-operation strategies and hypothetical dam-outlet structures were simulated using CE-QUAL-W2 hydrodynamic/temperature models of the MFWR system from Hills Creek Lake (HCR) to Lookout Point (LOP) and Dexter (DEX) Lakes to explore and understand the efficacy of potential flow and temperature mitigation options.Model scenarios were run in constructed wet, normal, and dry hydrologic calendar years, and designed to minimize the effects of Hills Creek and Lookout Point Dams on river temperature by prioritizing warmer lake surface releases in May–August and cooler, deep releases in September–December. Operational scenarios consisted of a range of modified release rate rules, relaxation of power-generation constraints, variations in the timing of refill and drawdown, and maintenance of different summer maximum lake levels at HCR and LOP. Structural scenarios included various combinations of hypothetical floating outlets near the lake surface and hypothetical new outlets at depth. Scenario results were compared to scenarios using existing operational rules that give temperature management some priority (Base), scenarios using pre-2012 operational rules that prioritized power generation over temperature management (NoBlend), and estimated temperatures from a without-dams condition (WoDams).Results of the tested model scenarios led to the following conclusions:The existing outlets at Lookout Point Dam, because of the range of depths, allow for greater temperature control than the two existing outlets at Hills Creek Dam that are relatively deep.Temperature control at HCR through operational scenarios generally was minimal near Hills Creek Dam, but improved downstream toward the head of LOP when decreased release rates held HCR at a low lake elevation year-round.Inflows from unregulated streams between HCR and LOP helped to dilute the effects of HCR and achieve more natural stream temperatures before the MFWR entered LOP.The relative benefit of any particular scenario depended on the location in the MFWR system used to assess the potential change, with most scenarios involving changes to Hills Creek Dam being less effective with increasing downstream distance, such as downstream of DEX.To achieve as much temperature control as the most successful structural scenarios, which were able to resemble without-dam conditions for part of the year, most operational scenarios had to be free of any power-generation requirements at Lookout Point Dam.Downstream of DEX, scenarios incorporating a hypothetical floating outlet at either HCR or LOP resulted in similar temperatures, with both scenarios causing a delay in the estimated spring Chinook egg emergence by about 9–10 days compared to base-case temperature-management scenarios.

33 CFR 110.127b - Flaming Gorge Lake, Wyoming-Utah.

Code of Federal Regulations, 2010 CFR

2010-07-01

... launching ramp to a point beyond the floating breakwater and then westerly, as established by the... following points, excluding a 150-foot-wide fairway, extending southeasterly from the launching ramp, as... inclosed by the shore and a line connecting the following points, excluding a 100-foot-wide fairway...

Wind tunnel research comparing lateral control devices, particularly at high angles of attack XI : various floating tip ailerons on both rectangular and tapered wings

NASA Technical Reports Server (NTRS)

Weick, Fred E; Harris, Thomas A

1933-01-01

Discussed here are a series of systematic tests being conducted to compare different lateral control devices with particular reference to their effectiveness at high angles of attack. The present tests were made with six different forms of floating tip ailerons of symmetrical section. The tests showed the effect of the various ailerons on the general performance characteristics of the wing, and on the lateral controllability and stability characteristics. In addition, the hinge moments were measured for the most interesting cases. The results are compared with those for a rectangular wing with ordinary ailerons and also with those for a rectangular wing having full-chord floating tip ailerons. Practically all the floating tip ailerons gave satisfactory rolling moments at all angles of attack and at the same time gave no adverse yawing moments of appreciable magnitude. The general performance characteristics with the floating tip ailerons, however, were relatively poor, especially the rate of climb. None of the floating tip ailerons entirely eliminated the auto rotational moments at angles of attack above the stall, but all of them gave lower moments than a plain wing. Some of the floating ailerons fluttered if given sufficiently large deflection, but this could have been eliminated by moving the hinge axis of the ailerons forward. Considering all points including hinge moments, the floating tip ailerons on the wing with 5:1 taper are probably the best of those which were tested.

Development of a Novel Floating In-situ Gelling System for Stomach Specific Drug Delivery of the Narrow Absorption Window Drug Baclofen.

PubMed

R Jivani, Rishad; N Patel, Chhagan; M Patel, Dashrath; P Jivani, Nurudin

2010-01-01

The present study deals with development of a floating in-situ gel of the narrow absorption window drug baclofen. Sodium alginate-based in-situ gelling systems were prepared by dissolving various concentrations of sodium alginate in deionized water, to which varying concentrations of drug and calcium bicarbonate were added. Fourier transform infrared spectroscopy (FTIR) and differential scanning calorimetry (DSC) were used to check the presence of any interaction between the drug and the excipients. A 3(2) full factorial design was used for optimization. The concentrations of sodium alginate (X1) and calcium bicarbonate (X2) were selected as the independent variables. The amount of the drug released after 1 h (Q1) and 10 h (Q10) and the viscosity of the solution were selected as the dependent variables. The gels were studied for their viscosity, in-vitro buoyancy and drug release. Contour plots were drawn for each dependent variable and check-point batches were prepared in order to get desirable release profiles. The drug release profiles were fitted into different kinetic models. The floating lag time and floating time found to be 2 min and 12 h respectively. A decreasing trend in drug release was observed with increasing concentrations of CaCO3. The computed values of Q1 and Q10 for the check-point batch were 25% and 86% respectively, compared to the experimental values of 27.1% and 88.34%. The similarity factor (f 2) for the check-point batch being 80.25 showed that the two dissolution profiles were similar. The drug release from the in-situ gel follows the Higuchi model, which indicates a diffusion-controlled release. A stomach specific in-situ gel of baclofen could be prepared using floating mechanism to increase the residence time of the drug in stomach and thereby increase the absorption.

STS-79 Flight Day 7

NASA Technical Reports Server (NTRS)

1996-01-01

On this seventh day of the STS-79 mission, the flight crew, Cmdr. William F. Readdy, Pilot Terrence W. Wilcutt, Mission Specialists, Thomas D. Akers, Shannon Lucid, Jay Apt, and Carl E. Walz, share a brief video tour of the Mir Space Station with flight controllers, taking a break from the transfer activities that has occupied the astronauts' time during three days of docked operations. Readdy and Apt floated through several of Mir's modules and back into Atlantis' double Spacehab module during the tour pointing out the numerous transfer items stowed on both spacecraft. Readdy, Wilcutt, Lucid and Blaha are seen discussing their mission in an interview with CNN's John Holliman.

A micro-computer-based system to compute magnetic variation

NASA Technical Reports Server (NTRS)

Kaul, Rajan

1987-01-01

A mathematical model of magnetic variation in the continental United States was implemented in the Ohio University Loran-C receiver. The model is based on a least squares fit of a polynomial function. The implementation on the microprocessor based Loran-C receiver is possible with the help of a math chip which performs 32 bit floating point mathematical operations. A Peripheral Interface Adapter is used to communicate between the 6502 based microcomputer and the 9511 math chip. The implementation provides magnetic variation data to the pilot as a function of latitude and longitude. The model and the real time implementation in the receiver are described.

Analysis and Implementation of Particle-to-Particle (P2P) Graphics Processor Unit (GPU) Kernel for Black-Box Adaptive Fast Multipole Method

DTIC Science & Technology

2015-06-01

5110P and 16 dx360M4 nodes each with one NVIDIA Kepler K20M/K40M GPU. Each node contained dual Intel Xeon E5-2670 (Sandy Bridge) central processing...kernel and as such does not employ multiple processors. This work makes use of a single processing core and a single NVIDIA Kepler K40 GK110...bandwidth (2 × 16 slot), 7.877 GFloat/s; Kepler K40 peak, 4,290 × 1 billion floating-point operations (GFLOPs), and 288 GB/s Kepler K40 memory

30 CFR 250.428 - What must I do in certain cementing and casing situations?

Code of Federal Regulations, 2010 CFR

2010-07-01

... point. (h) Need to use less than required cement for the surface casing during floating drilling... permafrost zone uncemented Fill the annulus with a liquid that has a freezing point below the minimum...

Onward to Petaflops Computing

NASA Technical Reports Server (NTRS)

Bailey, David H.; Chancellor, Marisa K. (Technical Monitor)

1997-01-01

With programs such as the US High Performance Computing and Communications Program (HPCCP), the attention of scientists and engineers worldwide has been focused on the potential of very high performance scientific computing, namely systems that are hundreds or thousands of times more powerful than those typically available in desktop systems at any given point in time. Extending the frontiers of computing in this manner has resulted in remarkable advances, both in computing technology itself and also in the various scientific and engineering disciplines that utilize these systems. Within the month or two, a sustained rate of 1 Tflop/s (also written 1 teraflops, or 10(exp 12) floating-point operations per second) is likely to be achieved by the 'ASCI Red' system at Sandia National Laboratory in New Mexico. With this objective in sight, it is reasonable to ask what lies ahead for high-end computing.

Seal Technology for Liquid Oxygen (LOX) Turbopumps

NASA Technical Reports Server (NTRS)

Shapiro, Wilbur; Hamm, Robert

1985-01-01

Two types of advanced seals for liquid oxygen (LOX) turbopumps were investigated. One was a spiral-groove face seal whose function is to seal high-pressure LOX at the impeller end of the turbopump. The other was a floating-ring, Rayleigh-step, helium buffered seal used to prevent LOX ingress to the turbine side of the unit. For each seal type, two sizes were investigated (50 and 20 mm). A turbine-driven test rig was designed and manufactured, and a test program was completed on the 50 mm floating-ring, Rayleigh-step, helium buffered seal. Significant results were: vaporization in the flow path could cause failure by overheating; therefore, the spiral-groove pumping portion of the seal that provides the fluid film must circulate fluid without disruption if vaporization occurs in the sealing dam. This is successfully accomplished by a pressure-balanced spiral-groove concept that is described. The spiral-groove configuration is affected by turbulence in the fluid film and pressure drops due to fluid inertia at sudden contractions. The net results of these effects are deep grooves, large operating films, and high power loss when compared against seals operating with laminar films. Turbulence and inertia are induced by the high-density and low-viscosity characteristics of LOX. The program clearly pointed out the need to consider system environmental factors such as thermal and centrifugal distortions and rotor vibrations in the seal design.

Using Tensor Completion Method to Achieving Better Coverage of Traffic State Estimation from Sparse Floating Car Data

PubMed Central

Ran, Bin; Song, Li; Cheng, Yang; Tan, Huachun

2016-01-01

Traffic state estimation from the floating car system is a challenging problem. The low penetration rate and random distribution make available floating car samples usually cover part space and time points of the road networks. To obtain a wide range of traffic state from the floating car system, many methods have been proposed to estimate the traffic state for the uncovered links. However, these methods cannot provide traffic state of the entire road networks. In this paper, the traffic state estimation is transformed to solve a missing data imputation problem, and the tensor completion framework is proposed to estimate missing traffic state. A tensor is constructed to model traffic state in which observed entries are directly derived from floating car system and unobserved traffic states are modeled as missing entries of constructed tensor. The constructed traffic state tensor can represent spatial and temporal correlations of traffic data and encode the multi-way properties of traffic state. The advantage of the proposed approach is that it can fully mine and utilize the multi-dimensional inherent correlations of traffic state. We tested the proposed approach on a well calibrated simulation network. Experimental results demonstrated that the proposed approach yield reliable traffic state estimation from very sparse floating car data, particularly when dealing with the floating car penetration rate is below 1%. PMID:27448326

Using Tensor Completion Method to Achieving Better Coverage of Traffic State Estimation from Sparse Floating Car Data.

PubMed

Ran, Bin; Song, Li; Zhang, Jian; Cheng, Yang; Tan, Huachun

2016-01-01

Traffic state estimation from the floating car system is a challenging problem. The low penetration rate and random distribution make available floating car samples usually cover part space and time points of the road networks. To obtain a wide range of traffic state from the floating car system, many methods have been proposed to estimate the traffic state for the uncovered links. However, these methods cannot provide traffic state of the entire road networks. In this paper, the traffic state estimation is transformed to solve a missing data imputation problem, and the tensor completion framework is proposed to estimate missing traffic state. A tensor is constructed to model traffic state in which observed entries are directly derived from floating car system and unobserved traffic states are modeled as missing entries of constructed tensor. The constructed traffic state tensor can represent spatial and temporal correlations of traffic data and encode the multi-way properties of traffic state. The advantage of the proposed approach is that it can fully mine and utilize the multi-dimensional inherent correlations of traffic state. We tested the proposed approach on a well calibrated simulation network. Experimental results demonstrated that the proposed approach yield reliable traffic state estimation from very sparse floating car data, particularly when dealing with the floating car penetration rate is below 1%.

14 CFR 23.527 - Hull and main float load factors.

Code of Federal Regulations, 2011 CFR

2011-01-01

... Water Loads § 23.527 Hull and main float load factors. (a) Water reaction load factors nw must be... landing cases EC28SE91.005 (b) The following values are used: (1) nw=water reaction load factor (that is, the water reaction divided by seaplane weight). (2) C1=empirical seaplane operations factor equal to 0...

First measurements with Argo flots in the Southern Baltic Sea

NASA Astrophysics Data System (ADS)

Walczowski, Waldemar; Goszczko, Ilona; Wieczorek, Piotr; Merchel, Malgorzata; Rak, Daniel

2017-04-01

The Argo programme is one of the most important elements of the ocean observing system. Currently almost 4000 Argo floats profile global oceans and deliver real time data. Originally Argo floats were developed for open ocean observations. Therefore a standard float can dive up to 2000 m and deep Argo floats are under development. However in the last years the shallow shelf seas become also interesting for Argo users. Institute of Oceanology Polish Academy of Sciences (IOPAN) participates in the Euro-Argo research infrastructure, the European contribution to Argo system. A legal and governance framework (Euro-Argo ERIC) was set up in May 2014. For a few years IOPAN has deployed floats mostly in the Nordic Seas and the European Arctic region. In the end of 2016 the first Polish Argo float was deployed in the Southern Baltic Sea. Building on the successful experience with Argo floats deployed by the Finnish oceanographers in the Bothnian Sea and Gotland Basin, the IOPAN float was launched in the Bornholm Deep during the fall cruise of IOPAN research vessel Oceania. The standard APEX float equipped with 2-way Iridium communication was used and different modes of operation, required for the specific conditions in the shallow and low saline Baltic Sea, were tested. Settings for the Baltic float are different than for the oceanic mode and were frequently changed during the mission to find the optimum solution. Changing the float parking depth during the mission allows for the limited control of the float drift direction. Results of a high resolution numerical forecast model for the Baltic Sea proved to be a valuable tool for determining the parking depth of the float in the different flow regimes. Trajectory and drift velocity of the Argo float deployed in the Southern Baltic depended strongly on the atmospheric forcing (in particular wind speed and direction), what was clearly manifested during the 'Axel' storm passing over the deployment area in January 2017. The first deployment showed clearly that Argo floats can be a useful tool for the Baltic Sea monitoring as the important element of a more complex, multidisciplinary observing system.

What is the size of a floating sheath? An answer

NASA Astrophysics Data System (ADS)

Voigt, Farina; Naggary, Schabnam; Brinkmann, Ralf Peter

2016-09-01

The formation of a non-neutral boundary sheath in front of material surfaces is universal plasma phenomenon. Despite several decades of research, however, not all related issues are fully clarified. In a recent paper, Chabert pointed out that this lack of clarity applies even to the seemingly innocuous question ``What the size of a floating sheath?'' This contribution attempts to provide an answer that is not arbitrary: The size of a floating sheath is defined as the plate separation of an equivalent parallel plate capacitor. The consequences of the definition are explored with the help of a self-consistent sheath model, and a comparison is made with other sheath size definitions. Deutsche Forschungsgemeinschaft within SFB TR 87.

Correlation of ISS Electric Potential Variations with Mission Operations

NASA Technical Reports Server (NTRS)

Willis, Emily M.; Minow, Joseph I.; Parker, Linda Neergaard

2014-01-01

Orbiting approximately 400 km above the Earth, the International Space Station (ISS) is a unique research laboratory used to conduct ground-breaking science experiments in space. The ISS has eight Solar Array Wings (SAW), and each wing is 11.7 meters wide and 35.1 meters long. The SAWs are controlled individually to maximize power output, minimize stress to the ISS structure, and minimize interference with other ISS operations such as vehicle dockings and Extra-Vehicular Activities (EVA). The Solar Arrays are designed to operate at 160 Volts. These large, high power solar arrays are negatively grounded to the ISS and collect charged particles (predominately electrons) as they travel through the space plasma in the Earth's ionosphere. If not controlled, this collected charge causes floating potential variations which can result in arcing, causing injury to the crew during an EVA or damage to hardware [1]. The environmental catalysts for ISS floating potential variations include plasma density and temperature fluctuations and magnetic induction from the Earth's magnetic field. These alone are not enough to cause concern for ISS, but when they are coupled with the large positive potential on the solar arrays, floating potentials up to negative 95 Volts have been observed. Our goal is to differentiate the operationally induced fluctuations in floating potentials from the environmental causes. Differentiating will help to determine what charging can be controlled, and we can then design the proper operations controls for charge collection mitigation. Additionally, the knowledge of how high power solar arrays interact with the environment and what regulations or design techniques can be employed to minimize charging impacts can be applied to future programs.

FloPSy - Search-Based Floating Point Constraint Solving for Symbolic Execution

NASA Astrophysics Data System (ADS)

Lakhotia, Kiran; Tillmann, Nikolai; Harman, Mark; de Halleux, Jonathan

Recently there has been an upsurge of interest in both, Search-Based Software Testing (SBST), and Dynamic Symbolic Execution (DSE). Each of these two approaches has complementary strengths and weaknesses, making it a natural choice to explore the degree to which the strengths of one can be exploited to offset the weakness of the other. This paper introduces an augmented version of DSE that uses a SBST-based approach to handling floating point computations, which are known to be problematic for vanilla DSE. The approach has been implemented as a plug in for the Microsoft Pex DSE testing tool. The paper presents results from both, standard evaluation benchmarks, and two open source programs.

From 16-bit to high-accuracy IDCT approximation: fruits of single architecture affliation

NASA Astrophysics Data System (ADS)

Liu, Lijie; Tran, Trac D.; Topiwala, Pankaj

2007-09-01

In this paper, we demonstrate an effective unified framework for high-accuracy approximation of the irrational co-effcient floating-point IDCT by a single integer-coeffcient fixed-point architecture. Our framework is based on a modified version of the Loeffler's sparse DCT factorization, and the IDCT architecture is constructed via a cascade of dyadic lifting steps and butterflies. We illustrate that simply varying the accuracy of the approximating parameters yields a large family of standard-compliant IDCTs, from rare 16-bit approximations catering to portable computing to ultra-high-accuracy 32-bit versions that virtually eliminate any drifting effect when pairing with the 64-bit floating-point IDCT at the encoder. Drifting performances of the proposed IDCTs along with existing popular IDCT algorithms in H.263+, MPEG-2 and MPEG-4 are also demonstrated.

Optimal trajectory planning of free-floating space manipulator using differential evolution algorithm

NASA Astrophysics Data System (ADS)

Wang, Mingming; Luo, Jianjun; Fang, Jing; Yuan, Jianping

2018-03-01

The existence of the path dependent dynamic singularities limits the volume of available workspace of free-floating space robot and induces enormous joint velocities when such singularities are met. In order to overcome this demerit, this paper presents an optimal joint trajectory planning method using forward kinematics equations of free-floating space robot, while joint motion laws are delineated with application of the concept of reaction null-space. Bézier curve, in conjunction with the null-space column vectors, are applied to describe the joint trajectories. Considering the forward kinematics equations of the free-floating space robot, the trajectory planning issue is consequently transferred to an optimization issue while the control points to construct the Bézier curve are the design variables. A constrained differential evolution (DE) scheme with premature handling strategy is implemented to find the optimal solution of the design variables while specific objectives and imposed constraints are satisfied. Differ from traditional methods, we synthesize null-space and specialized curve to provide a novel viewpoint for trajectory planning of free-floating space robot. Simulation results are presented for trajectory planning of 7 degree-of-freedom (DOF) kinematically redundant manipulator mounted on a free-floating spacecraft and demonstrate the feasibility and effectiveness of the proposed method.

rpe v5: an emulator for reduced floating-point precision in large numerical simulations

NASA Astrophysics Data System (ADS)

Dawson, Andrew; Düben, Peter D.

2017-06-01

This paper describes the rpe (reduced-precision emulator) library which has the capability to emulate the use of arbitrary reduced floating-point precision within large numerical models written in Fortran. The rpe software allows model developers to test how reduced floating-point precision affects the result of their simulations without having to make extensive code changes or port the model onto specialized hardware. The software can be used to identify parts of a program that are problematic for numerical precision and to guide changes to the program to allow a stronger reduction in precision.The development of rpe was motivated by the strong demand for more computing power. If numerical precision can be reduced for an application under consideration while still achieving results of acceptable quality, computational cost can be reduced, since a reduction in numerical precision may allow an increase in performance or a reduction in power consumption. For simulations with weather and climate models, savings due to a reduction in precision could be reinvested to allow model simulations at higher spatial resolution or complexity, or to increase the number of ensemble members to improve predictions. rpe was developed with a particular focus on the community of weather and climate modelling, but the software could be used with numerical simulations from other domains.

Recent advances in lossy compression of scientific floating-point data

NASA Astrophysics Data System (ADS)

Lindstrom, P.

2017-12-01

With a continuing exponential trend in supercomputer performance, ever larger data sets are being generated through numerical simulation. Bandwidth and storage capacity are, however, not keeping pace with this increase in data size, causing significant data movement bottlenecks in simulation codes and substantial monetary costs associated with archiving vast volumes of data. Worse yet, ever smaller fractions of data generated can be stored for further analysis, where scientists frequently rely on decimating or averaging large data sets in time and/or space. One way to mitigate these problems is to employ data compression to reduce data volumes. However, lossless compression of floating-point data can achieve only very modest size reductions on the order of 10-50%. We present ZFP and FPZIP, two state-of-the-art lossy compressors for structured floating-point data that routinely achieve one to two orders of magnitude reduction with little to no impact on the accuracy of visualization and quantitative data analysis. We provide examples of the use of such lossy compressors in climate and seismic modeling applications to effectively accelerate I/O and reduce storage requirements. We further discuss how the design decisions behind these and other compressors impact error distributions and other statistical and differential properties, including derived quantities of interest relevant to each science application.

[The effect of floating-needle therapy combined with rehabilitation training for the hand function recovery of post-stroke patients].

PubMed

Yang, Jiangxia; Xiao, Hong

2015-08-01

To explore the improvement of hand motion function,spasm and self-care ability of daily life for stroke patients treated with floating-needle combined with rehabilitation training. Eighty hand spasm patients of post-stroke within one year after stroke were randomly divided into an observation group and a control group, 40 cases in each one. In the two groups, rehabilitation was adopted for eight weeks,once a day,40 min one time. In the observation group, based on the above treatment and according to muscle fascia trigger point, 2~3 points in both the internal and external sides of forearm were treated with floating-needle. The positive or passive flexion and extension of wrist and knuckle till the relief of spasm hand was combined. The floating-needle therapy was given for eight weeks, on the first three days once a day and later once every other day. Modified Ashworth Scale(MAS), activity of daily life(ADL, Barthel index) scores and Fugl-Meyer(FMA) scores were used to assess the spasm hand degree,activity of daily life and hand motion function before and after 7-day, 14-day and 8-week treatment. After 7-day, 14-day and 8-week treatment, MAS scores were apparently lower than those before treatment in the two groups(all P<0. 05), and Barthel scores and FMA scores were obviously higher than those before-treatment(all P<0. 05). After 14-day and 8-week treatment, FMA scores in the observation group were markedly higher than those in the control group(both P<0. 05). Floating-needle therapy combined with rehabilitation training and simple rehabilitation training could both improve hand spasm degree, hand function and activity of daily life of post-stroke patients, but floating-needle therapy combined with rehabilitation training is superior to simple rehabilitation training for the improvement of hand function.

Prevention of development of postoperative dysesthesia in transforaminal percutaneous endoscopic lumbar discectomy for intracanalicular lumbar disc herniation: floating retraction technique.

PubMed

Cho, J Y; Lee, S-H; Lee, H-Y

2011-10-01

Transforaminal percutaneous endoscopic lumbar discectomy (PELD) has become a routine surgical procedure because it is minimally invasive. Perioperative complications such as dural injury, infection, nerve root irritation and recurrence can occur not only with PELD, but also with conventional open microsurgery. In contrast, post-operative dysesthesia (POD) due to existing dorsal root ganglion (DRG) injury is a unique complication of PELD. When POD occurs, even if the traversing root has been successfully decompressed, it hinders swift recovery and delays the return to daily routines. Thus, prevention of POD is the key to successful and widespread use of PELD. From January 2006 to December 2008, 154 patients underwent percutaneous endoscopic discectomy by floating retraction technique at 160 disc levels under local anesthesia. This approach towards the superomedial border of the lower pedicle and the cannula can be placed by gentle retraction of the root with perineural fat instead of direct compression of dorsal root ganglion. The clinical outcomes were assessed using the Visual Analogue Scale (VAS, 0-10 point) for radicular pain and low back pain, and using the Oswestry Disability Index (ODI) for functional status. Perioperative complications and recurrence were reviewed. The mean age was 45 years, the mean operative time was 36 min and the mean follow-up period was 3.4 years. The mean hospital stay for endoscopic discectomy was 1.8 days. No patient underwent repeated PELD or convert microsurgery by incomplete removal of the ruptured particle. All patients experienced early relief of symptoms, as determined by VAS and ODI. No patient developed POD. 1 patient experienced dural injury. There was 1 case of discitis. The recurrence rate was 1.95% (3 patients). Transforaminal percutaneous endoscopic lumbar discectomy for intracanalicular lumbar disc herniation is a safe and effective procedure. The floating retraction technique is recommended to avoid development of POD. © Georg Thieme Verlag KG Stuttgart · New York.

Analysis of Free-floating Bike Sharing and Insights on System Operations : or Analyzing Mobility Patterns and Imbalance of Free Floating Bike Sharing Systems

DOT National Transportation Integrated Search

2018-01-31

Aritra Pal (ORCID ID 0000-0002-2256-2464) Yu Zhang (ORCID ID 0000-0003-1202-626X) Changhyun Kwon (ORCID ID 0000-0001-8455-6396) Bike Sharing is a sustainable mode of urban mobility, not only for regular commuters but also for casual users and tourist...

40 CFR Table 1 to Subpart Bbbbbb... - Applicability Criteria, Emission Limits, and Management Practices for Storage Tanks

Code of Federal Regulations, 2010 CFR

2010-07-01

... and operate each internal and external floating roof gasoline storage tank according to the applicable... (b) Equip each internal floating roof gasoline storage tank according to the requirements in § 60... the requirements in § 60.112b(a)(1)(iv) through (ix) of this chapter; and (c) Equip each external...

STS-26 Pilot Covey floats in life raft during JSC WETF exercises

NASA Technical Reports Server (NTRS)

1988-01-01

STS-26 Discovery, Orbiter Vehicle (OV) 103, Pilot Richard O. Covey, wearing the newly designed launch and entry suit (LES), floats in single-occupant life raft in JSC Weightless Environment Training Facility (WETF) Bldg 29 pool. The simulation of the escape and rescue operations utilized the crew escape system (CES) pole method of egress from the Space Shuttle.

Campaign for Levitation in LDX

NASA Astrophysics Data System (ADS)

Garnier, D. T.; Hansen, A. K.; Mauel, M. E.; Ortiz, E. E.; Boxer, A. C.; Ellsworth, J. L.; Karim, I.; Kesner, J.; Michael, P. C.; Zhukovsky, A.

2006-10-01

In the past year, preparations have been made for the first flight of the Levitated Dipole Experiment (LDX). LDX, which consists of a 560 kg superconducting coil floating within a 5 m diameter vacuum chamber, is designed to study fusion relevant plasmas confined in a dipole magnetic field. During the spring, a high temperature superconducting levitation coil was integrated into the LDX facility. Testing was undertaken to verify the thermal performance of the coil under expected levitation conditions. In addition, a real-time operating system digital control system was developed that will be used for the levitation control. In July, plasma experiments were conducted with all superconducting magnets in operation. While still supported, roughly 75% of the weight of the floating coil was magnetically lifted by the levitation coil above. A series of plasma experiments were conducted with the same magnetic geometry as will be the case during levitation. During August, the second generation launcher system will be installed. The launcher, which retracts beyond the plasma's last closed field lines during operation, is designed to safely catch the floating coil following an unexpected loss of control. After this installation, levitation experiments will commence.

Dynamic response mitigation of floating wind turbine platforms using tuned liquid column dampers.

PubMed

Jaksic, V; Wright, C S; Murphy, J; Afeef, C; Ali, S F; Mandic, D P; Pakrashi, V

2015-02-28

In this paper, we experimentally study and compare the effects of three combinations of multiple tuned liquid column dampers (MTLCDs) on the dynamic performance of a model floating tension-leg platform (TLP) structure in a wave basin. The structural stability and safety of the floating structure during operation and maintenance is of concern for the performance of a renewable energy device that it might be supporting. The dynamic responses of the structure should thus be limited for these renewable energy devices to perform as intended. This issue is particularly important during the operation of a TLP in extreme weather conditions. Tuned liquid column dampers (TLCDs) can use the power of sloshing water to reduce surge motions of a floating TLP exposed to wind and waves. This paper demonstrates the potential of MTLCDs in reducing dynamic responses of a scaled TLP model through an experimental study. The potential of using output-only statistical markers for monitoring changes in structural conditions is also investigated through the application of a delay vector variance (DVV) marker for different conditions of control for the experiments. © 2015 The Author(s) Published by the Royal Society. All rights reserved.

Parametric studies on floating pad journal bearing for high speed cryogenic turboexpanders

NASA Astrophysics Data System (ADS)

Jain, A.; Jadhav, M. M.; Karimulla, S.; Chakravarty, A.

2017-12-01

Most modern medium and large capacity helium liquefaction/refrigeration plants employ high speed cryogenic turboexpanders in their refrigeration/liquefaction cycles as active cooling devices. The operating speed of these turboexpanders is in the range of 3000-5000 Hz and hence specialized types of bearings are required. Floating pad journal bearing, which is a special type of tilting pad journal bearing, where mechanical pivots are absent and pads are fully suspended in gas, can be a good solution for stable operation of these high speed compact rotors. The pads are separated from shaft as well as from housing by fluid film between them, and both these sides of pad are interconnected by a network of feed holes. The work presented in this article aims to characterize floating pad journal bearings through parametric studies. The steady state performance characteristics of the bearing are represented by load capacity, stiffness coefficients and heat generation rate of the bearing. The geometrical parameters such as bearing clearances, preload of pads, etc. are varied and performance characteristics of the floating pad journal bearing are studied and presented. The dependence of stiffness coefficients on rotational speed of shaft is also analyzed.

Real-time electroholography using a multiple-graphics processing unit cluster system with a single spatial light modulator and the InfiniBand network

NASA Astrophysics Data System (ADS)

Niwase, Hiroaki; Takada, Naoki; Araki, Hiromitsu; Maeda, Yuki; Fujiwara, Masato; Nakayama, Hirotaka; Kakue, Takashi; Shimobaba, Tomoyoshi; Ito, Tomoyoshi

2016-09-01

Parallel calculations of large-pixel-count computer-generated holograms (CGHs) are suitable for multiple-graphics processing unit (multi-GPU) cluster systems. However, it is not easy for a multi-GPU cluster system to accomplish fast CGH calculations when CGH transfers between PCs are required. In these cases, the CGH transfer between the PCs becomes a bottleneck. Usually, this problem occurs only in multi-GPU cluster systems with a single spatial light modulator. To overcome this problem, we propose a simple method using the InfiniBand network. The computational speed of the proposed method using 13 GPUs (NVIDIA GeForce GTX TITAN X) was more than 3000 times faster than that of a CPU (Intel Core i7 4770) when the number of three-dimensional (3-D) object points exceeded 20,480. In practice, we achieved ˜40 tera floating point operations per second (TFLOPS) when the number of 3-D object points exceeded 40,960. Our proposed method was able to reconstruct a real-time movie of a 3-D object comprising 95,949 points.

Evaluating the Cost, Safety, and Proliferation Risks of Small Floating Nuclear Reactors.

PubMed

Ford, Michael J; Abdulla, Ahmed; Morgan, M Granger

2017-11-01

It is hard to see how our energy system can be decarbonized if the world abandons nuclear power, but equally hard to introduce the technology in nonnuclear energy states. This is especially true in countries with limited technical, institutional, and regulatory capabilities, where safety and proliferation concerns are acute. Given the need to achieve serious emissions mitigation by mid-century, and the multidecadal effort required to develop robust nuclear governance institutions, we must look to other models that might facilitate nuclear plant deployment while mitigating the technology's risks. One such deployment paradigm is the build-own-operate-return model. Because returning small land-based reactors containing spent fuel is infeasible, we evaluate the cost, safety, and proliferation risks of a system in which small modular reactors are manufactured in a factory, and then deployed to a customer nation on a floating platform. This floating small modular reactor would be owned and operated by a single entity and returned unopened to the developed state for refueling. We developed a decision model that allows for a comparison of floating and land-based alternatives considering key International Atomic Energy Agency plant-siting criteria. Abandoning onsite refueling is beneficial, and floating reactors built in a central facility can potentially reduce the risk of cost overruns and the consequences of accidents. However, if the floating platform must be built to military-grade specifications, then the cost would be much higher than a land-based system. The analysis tool presented is flexible, and can assist planners in determining the scope of risks and uncertainty associated with different deployment options. © 2017 Society for Risk Analysis.

Evaluation of the SPAR thermal analyzer on the CYBER-203 computer

NASA Technical Reports Server (NTRS)

Robinson, J. C.; Riley, K. M.; Haftka, R. T.

1982-01-01

The use of the CYBER 203 vector computer for thermal analysis is investigated. Strengths of the CYBER 203 include the ability to perform, in vector mode using a 64 bit word, 50 million floating point operations per second (MFLOPS) for addition and subtraction, 25 MFLOPS for multiplication and 12.5 MFLOPS for division. The speed of scalar operation is comparable to that of a CDC 7600 and is some 2 to 3 times faster than Langley's CYBER 175s. The CYBER 203 has 1,048,576 64-bit words of real memory with an 80 nanosecond (nsec) access time. Memory is bit addressable and provides single error correction, double error detection (SECDED) capability. The virtual memory capability handles data in either 512 or 65,536 word pages. The machine has 256 registers with a 40 nsec access time. The weaknesses of the CYBER 203 include the amount of vector operation overhead and some data storage limitations. In vector operations there is a considerable amount of time before a single result is produced so that vector calculation speed is slower than scalar operation for short vectors.

Fpga based L-band pulse doppler radar design and implementation

NASA Astrophysics Data System (ADS)

Savci, Kubilay

As its name implies RADAR (Radio Detection and Ranging) is an electromagnetic sensor used for detection and locating targets from their return signals. Radar systems propagate electromagnetic energy, from the antenna which is in part intercepted by an object. Objects reradiate a portion of energy which is captured by the radar receiver. The received signal is then processed for information extraction. Radar systems are widely used for surveillance, air security, navigation, weather hazard detection, as well as remote sensing applications. In this work, an FPGA based L-band Pulse Doppler radar prototype, which is used for target detection, localization and velocity calculation has been built and a general-purpose Pulse Doppler radar processor has been developed. This radar is a ground based stationary monopulse radar, which transmits a short pulse with a certain pulse repetition frequency (PRF). Return signals from the target are processed and information about their location and velocity is extracted. Discrete components are used for the transmitter and receiver chain. The hardware solution is based on Xilinx Virtex-6 ML605 FPGA board, responsible for the control of the radar system and the digital signal processing of the received signal, which involves Constant False Alarm Rate (CFAR) detection and Pulse Doppler processing. The algorithm is implemented in MATLAB/SIMULINK using the Xilinx System Generator for DSP tool. The field programmable gate arrays (FPGA) implementation of the radar system provides the flexibility of changing parameters such as the PRF and pulse length therefore it can be used with different radar configurations as well. A VHDL design has been developed for 1Gbit Ethernet connection to transfer digitized return signal and detection results to PC. An A-Scope software has been developed with C# programming language to display time domain radar signals and detection results on PC. Data are processed both in FPGA chip and on PC. FPGA uses fixed point arithmetic operations as it is fast and facilitates source requirement as it consumes less hardware than floating point arithmetic operations. The software uses floating point arithmetic operations, which ensure precision in processing at the expense of speed. The functionality of the radar system has been tested for experimental validation in the field with a moving car and the validation of submodules are tested with synthetic data simulated on MATLAB.

40 CFR 60.691 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... collection point for stormwater runoff received directly from refinery surfaces and for refinery wastewater... chamber in a stationary manner and which does not move with fluctuations in wastewater levels. Floating... separator. Junction box means a manhole or access point to a wastewater sewer system line. No detectable...

A prospective study comparing conservative with operative treatment in patients with a 'floating shoulder' including assessment of the prognostic value of the glenopolar angle.

PubMed

Yadav, V; Khare, G N; Singh, S; Kumaraswamy, V; Sharma, N; Rai, A K; Ramaswamy, A G; Sharma, H

2013-06-01

Both conservative and operative forms of treatment have been recommended for patients with a 'floating shoulder'. We compared the results of conservative and operative treatment in 25 patients with this injury and investigated the use of the glenopolar angle (GPA) as an indicator of the functional outcome. A total of 13 patients (ten male and three female; mean age 32.5 years (24.7 to 40.4)) were treated conservatively and 12 patients (ten male and two female; mean age 33.67 years (24.6 to 42.7)) were treated operatively by fixation of the clavicular fracture alone. Outcome was assessed using the Herscovici score, which was also related to changes in the GPA at one year post-operatively. The mean Herscovici score was significantly better three months and two years after the injury in the operative group (p < 0.001 and p = 0.003, respectively). There was a negative correlation between the change in GPA and the Herscovici score at two years follow-up in both the conservative and operative groups, but neither were statistically significant (r = -0.295 and r = -0.19, respectively). There was a significant difference between the pre- and post-operative GPA in the operative group (p = 0.017). When compared with conservative treatment, fixation of the clavicle alone gives better results in the treatment of patients with a floating shoulder. The GPA changes significantly with fixation of clavicle alone but there is no significant correlation between the pre-injury GPA and the final clinical outcome in these patients.

Combined GPS/GLONASS Precise Point Positioning with Fixed GPS Ambiguities

PubMed Central

Pan, Lin; Cai, Changsheng; Santerre, Rock; Zhu, Jianjun

2014-01-01

Precise point positioning (PPP) technology is mostly implemented with an ambiguity-float solution. Its performance may be further improved by performing ambiguity-fixed resolution. Currently, the PPP integer ambiguity resolutions (IARs) are mainly based on GPS-only measurements. The integration of GPS and GLONASS can speed up the convergence and increase the accuracy of float ambiguity estimates, which contributes to enhancing the success rate and reliability of fixing ambiguities. This paper presents an approach of combined GPS/GLONASS PPP with fixed GPS ambiguities (GGPPP-FGA) in which GPS ambiguities are fixed into integers, while all GLONASS ambiguities are kept as float values. An improved minimum constellation method (MCM) is proposed to enhance the efficiency of GPS ambiguity fixing. Datasets from 20 globally distributed stations on two consecutive days are employed to investigate the performance of the GGPPP-FGA, including the positioning accuracy, convergence time and the time to first fix (TTFF). All datasets are processed for a time span of three hours in three scenarios, i.e., the GPS ambiguity-float solution, the GPS ambiguity-fixed resolution and the GGPPP-FGA resolution. The results indicate that the performance of the GPS ambiguity-fixed resolutions is significantly better than that of the GPS ambiguity-float solutions. In addition, the GGPPP-FGA improves the positioning accuracy by 38%, 25% and 44% and reduces the convergence time by 36%, 36% and 29% in the east, north and up coordinate components over the GPS-only ambiguity-fixed resolutions, respectively. Moreover, the TTFF is reduced by 27% after adding GLONASS observations. Wilcoxon rank sum tests and chi-square two-sample tests are made to examine the significance of the improvement on the positioning accuracy, convergence time and TTFF. PMID:25237901

Parametric study of two-body floating-point wave absorber

NASA Astrophysics Data System (ADS)

Amiri, Atena; Panahi, Roozbeh; Radfar, Soheil

2016-03-01

In this paper, we present a comprehensive numerical simulation of a point wave absorber in deep water. Analyses are performed in both the frequency and time domains. The converter is a two-body floating-point absorber (FPA) with one degree of freedom in the heave direction. Its two parts are connected by a linear mass-spring-damper system. The commercial ANSYS-AQWA software used in this study performs well in considering validations. The velocity potential is obtained by assuming incompressible and irrotational flow. As such, we investigated the effects of wave characteristics on energy conversion and device efficiency, including wave height and wave period, as well as the device diameter, draft, geometry, and damping coefficient. To validate the model, we compared our numerical results with those from similar experiments. Our study results can clearly help to maximize the converter's efficiency when considering specific conditions.

Correlation of ISS Electric Potential Variations with Mission Operations

NASA Technical Reports Server (NTRS)

Willis, Emily M.; Minow, Joseph I.; Parker, Linda Neergaard

2014-01-01

Spacecraft charging on the International Space Station (ISS) is caused by a complex combination of the low Earth orbit plasma environment, space weather events, operations of the high voltage solar arrays, and changes in the ISS configuration and orbit parameters. Measurements of the ionospheric electron density and temperature along the ISS orbit and variations in the ISS electric potential are obtained from the Floating Potential Measurement Unit (FPMU) suite of four plasma instruments (two Langmuir probes, a Floating Potential Probe, and a Plasma Impedance Probe) on the ISS. These instruments provide a unique capability for monitoring the response of the ISS electric potential to variations in the space environment, changes in vehicle configuration, and operational solar array power manipulation. In particular, rapid variations in ISS potential during solar array operations on time scales of tens of milliseconds can be monitored due to the 128 Hz sample rate of the Floating Potential Probe providing an interesting insight into high voltage solar array interaction with the space plasma environment. Comparing the FPMU data with the ISS operations timeline and solar array data provides a means for correlating some of the more complex and interesting ISS electric potential variations with mission operations. In addition, recent extensions and improvements to the ISS data downlink capabilities have allowed more operating time for the FPMU than ever before. The FPMU was operated for over 200 days in 2013 resulting in the largest data set ever recorded in a single year for the ISS. In this paper we provide examples of a number of the more interesting ISS charging events observed during the 2013 operations including examples of rapid charging events due to solar array power operations, auroral charging events, and other charging behavior related to ISS mission operations.

Correlation of ISS Electric Potential Variations with Mission Operations

NASA Technical Reports Server (NTRS)

Willis, Emily M.; Minow, Joseph I.; Parker, Linda Neergaard

2014-01-01

Spacecraft charging on the International Space Station (ISS) is caused by a complex mix of the low Earth orbit plasma environment, space weather events, operations of the high voltage solar arrays, and changes in the ISS configuration and orbit parameters. Measurements of the ionospheric electron density and temperature along the ISS orbit and variations in the ISS electric potential are obtained from the Floating Potential Measurement Unit (FPMU) suite of four plasma instruments (two Langmuir probes, a Floating Potential Probe, and a Plasma Impedance Probe) on the ISS. These instruments provide a unique capability for monitoring the response of the ISS electric potential to variations in the space environment, changes in vehicle configuration, and operational solar array power manipulation. In particular, rapid variations in ISS potential during solar array operations on time scales of tens of milliseconds can be monitored due to the 128 Hz sample rate of the Floating Potential Probe providing an interesting insight into high voltage solar array interaction with the space plasma environment. Comparing the FPMU data with the ISS operations timeline and solar array data provides a means for correlating some of the more complex and interesting ISS electric potential variations with mission operations. In addition, recent extensions and improvements to the ISS data downlink capabilities have allowed more operating time for the FPMU than ever before. The FPMU was operated for over 200 days in 2013 resulting in the largest data set ever recorded in a single year for the ISS. This presentation will provide examples of a number of the more interesting ISS charging events observed during the 2013 operations including examples of rapid charging events due to solar array power operations, auroral charging events, and other charging behavior related to ISS mission operations.

An array processing system for lunar geochemical and geophysical data

NASA Technical Reports Server (NTRS)

Eliason, E. M.; Soderblom, L. A.

1977-01-01

A computerized array processing system has been developed to reduce, analyze, display, and correlate a large number of orbital and earth-based geochemical, geophysical, and geological measurements of the moon on a global scale. The system supports the activities of a consortium of about 30 lunar scientists involved in data synthesis studies. The system was modeled after standard digital image-processing techniques but differs in that processing is performed with floating point precision rather than integer precision. Because of flexibility in floating-point image processing, a series of techniques that are impossible or cumbersome in conventional integer processing were developed to perform optimum interpolation and smoothing of data. Recently color maps of about 25 lunar geophysical and geochemical variables have been generated.

Vectorization of a classical trajectory code on a floating point systems, Inc. Model 164 attached processor.

PubMed

Kraus, Wayne A; Wagner, Albert F

1986-04-01

A triatomic classical trajectory code has been modified by extensive vectorization of the algorithms to achieve much improved performance on an FPS 164 attached processor. Extensive timings on both the FPS 164 and a VAX 11/780 with floating point accelerator are presented as a function of the number of trajectories simultaneously run. The timing tests involve a potential energy surface of the LEPS variety and trajectories with 1000 time steps. The results indicate that vectorization results in timing improvements on both the VAX and the FPS. For larger numbers of trajectories run simultaneously, up to a factor of 25 improvement in speed occurs between VAX and FPS vectorized code. Copyright © 1986 John Wiley & Sons, Inc.

A micro-computer based system to compute magnetic variation

NASA Technical Reports Server (NTRS)

Kaul, R.

1984-01-01

A mathematical model of magnetic variation in the continental United States (COT48) was implemented in the Ohio University LORAN C receiver. The model is based on a least squares fit of a polynomial function. The implementation on the microprocessor based LORAN C receiver is possible with the help of a math chip, Am9511 which performs 32 bit floating point mathematical operations. A Peripheral Interface Adapter (M6520) is used to communicate between the 6502 based micro-computer and the 9511 math chip. The implementation provides magnetic variation data to the pilot as a function of latitude and longitude. The model and the real time implementation in the receiver are described.

Theorem Proving in Intel Hardware Design

NASA Technical Reports Server (NTRS)

O'Leary, John

2009-01-01

For the past decade, a framework combining model checking (symbolic trajectory evaluation) and higher-order logic theorem proving has been in production use at Intel. Our tools and methodology have been used to formally verify execution cluster functionality (including floating-point operations) for a number of Intel products, including the Pentium(Registered TradeMark)4 and Core(TradeMark)i7 processors. Hardware verification in 2009 is much more challenging than it was in 1999 - today s CPU chip designs contain many processor cores and significant firmware content. This talk will attempt to distill the lessons learned over the past ten years, discuss how they apply to today s problems, outline some future directions.

Classifying Floating Potential Measurement Unit Data Products as Science Data

NASA Technical Reports Server (NTRS)

Coffey, Victoria; Minow, Joseph

2015-01-01

We are Co-Investigators for the Floating Potential Measurement Unit (FPMU) on the International Space Station (ISS) and members of the FPMU operations and data analysis team. We are providing this memo for the purpose of classifying raw and processed FPMU data products and ancillary data as NASA science data with unrestricted, public availability in order to best support science uses of the data.

STS-26 Pilot Covey floats in life raft during JSC WETF exercises

NASA Technical Reports Server (NTRS)

1988-01-01

STS-26 Discovery, Orbiter Vehicle (OV) 103, Pilot Richard O. Covey, wearing newly designed launch and entry suit (LES), floats in single-occupant life raft during simulations in the JSC Weightless Environment Training Facility Bldg 29 pool. During the simulation of escape and rescue operations, the crew escape system (CES) pole mode of egress from the Space Shuttle was utilized.

Sensor Buoy System for Monitoring Renewable Marine Energy Resources.

PubMed

García, Emilio; Quiles, Eduardo; Correcher, Antonio; Morant, Francisco

2018-03-22

In this paper we present a multi-sensor floating system designed to monitor marine energy parameters, in order to sample wind, wave, and marine current energy resources. For this purpose, a set of dedicated sensors to measure the height and period of the waves, wind, and marine current intensity and direction have been selected and installed in the system. The floating device incorporates wind and marine current turbines for renewable energy self-consumption and to carry out complementary studies on the stability of such a system. The feasibility, safety, sensor communications, and buoy stability of the floating device have been successfully checked in real operating conditions.

Sensor Buoy System for Monitoring Renewable Marine Energy Resources

PubMed Central

García, Emilio; Morant, Francisco

2018-01-01

In this paper we present a multi-sensor floating system designed to monitor marine energy parameters, in order to sample wind, wave, and marine current energy resources. For this purpose, a set of dedicated sensors to measure the height and period of the waves, wind, and marine current intensity and direction have been selected and installed in the system. The floating device incorporates wind and marine current turbines for renewable energy self-consumption and to carry out complementary studies on the stability of such a system. The feasibility, safety, sensor communications, and buoy stability of the floating device have been successfully checked in real operating conditions. PMID:29565823

The anatomy of floating shock fitting. [shock waves computation for flow field

NASA Technical Reports Server (NTRS)

Salas, M. D.

1975-01-01

The floating shock fitting technique is examined. Second-order difference formulas are developed for the computation of discontinuities. A procedure is developed to compute mesh points that are crossed by discontinuities. The technique is applied to the calculation of internal two-dimensional flows with arbitrary number of shock waves and contact surfaces. A new procedure, based on the coalescence of characteristics, is developed to detect the formation of shock waves. Results are presented to validate and demonstrate the versatility of the technique.

High-Dimensional Bayesian Geostatistics

PubMed Central

Banerjee, Sudipto

2017-01-01

With the growing capabilities of Geographic Information Systems (GIS) and user-friendly software, statisticians today routinely encounter geographically referenced data containing observations from a large number of spatial locations and time points. Over the last decade, hierarchical spatiotemporal process models have become widely deployed statistical tools for researchers to better understand the complex nature of spatial and temporal variability. However, fitting hierarchical spatiotemporal models often involves expensive matrix computations with complexity increasing in cubic order for the number of spatial locations and temporal points. This renders such models unfeasible for large data sets. This article offers a focused review of two methods for constructing well-defined highly scalable spatiotemporal stochastic processes. Both these processes can be used as “priors” for spatiotemporal random fields. The first approach constructs a low-rank process operating on a lower-dimensional subspace. The second approach constructs a Nearest-Neighbor Gaussian Process (NNGP) that ensures sparse precision matrices for its finite realizations. Both processes can be exploited as a scalable prior embedded within a rich hierarchical modeling framework to deliver full Bayesian inference. These approaches can be described as model-based solutions for big spatiotemporal datasets. The models ensure that the algorithmic complexity has ~ n floating point operations (flops), where n the number of spatial locations (per iteration). We compare these methods and provide some insight into their methodological underpinnings. PMID:29391920

High-Dimensional Bayesian Geostatistics.

PubMed

Banerjee, Sudipto

2017-06-01

With the growing capabilities of Geographic Information Systems (GIS) and user-friendly software, statisticians today routinely encounter geographically referenced data containing observations from a large number of spatial locations and time points. Over the last decade, hierarchical spatiotemporal process models have become widely deployed statistical tools for researchers to better understand the complex nature of spatial and temporal variability. However, fitting hierarchical spatiotemporal models often involves expensive matrix computations with complexity increasing in cubic order for the number of spatial locations and temporal points. This renders such models unfeasible for large data sets. This article offers a focused review of two methods for constructing well-defined highly scalable spatiotemporal stochastic processes. Both these processes can be used as "priors" for spatiotemporal random fields. The first approach constructs a low-rank process operating on a lower-dimensional subspace. The second approach constructs a Nearest-Neighbor Gaussian Process (NNGP) that ensures sparse precision matrices for its finite realizations. Both processes can be exploited as a scalable prior embedded within a rich hierarchical modeling framework to deliver full Bayesian inference. These approaches can be described as model-based solutions for big spatiotemporal datasets. The models ensure that the algorithmic complexity has ~ n floating point operations (flops), where n the number of spatial locations (per iteration). We compare these methods and provide some insight into their methodological underpinnings.

Description of signature scales in a floating wind turbine model wake subjected to varying turbulence intensity

NASA Astrophysics Data System (ADS)

Kadum, Hawwa; Rockel, Stanislav; Holling, Michael; Peinke, Joachim; Cal, Raul Bayon

2017-11-01

The wake behind a floating model horizontal axis wind turbine during pitch motion is investigated and compared to a fixed wind turbine wake. An experiment is conducted in an acoustic wind tunnel where hot-wire data are acquired at five downstream locations. At each downstream location, a rake of 16 hot-wires was used with placement of the probes increasing radially in the vertical, horizontal, and diagonally at 45 deg. In addition, the effect of turbulence intensity on the floating wake is examined by subjecting the wind turbine to different inflow conditions controlled through three settings in the wind tunnel grid, a passive and two active protocols, thus varying in intensity. The wakes are inspected by statistics of the point measurements, where the various length/time scales are considered. The wake characteristics for a floating wind turbine are compared to a fixed turbine, and uncovering its features; relevant as the demand for exploiting deep waters in wind energy is increasing.

A hierarchical graph neuron scheme for real-time pattern recognition.

PubMed

Nasution, B B; Khan, A I

2008-02-01

The hierarchical graph neuron (HGN) implements a single cycle memorization and recall operation through a novel algorithmic design. The HGN is an improvement on the already published original graph neuron (GN) algorithm. In this improved approach, it recognizes incomplete/noisy patterns. It also resolves the crosstalk problem, which is identified in the previous publications, within closely matched patterns. To accomplish this, the HGN links multiple GN networks for filtering noise and crosstalk out of pattern data inputs. Intrinsically, the HGN is a lightweight in-network processing algorithm which does not require expensive floating point computations; hence, it is very suitable for real-time applications and tiny devices such as the wireless sensor networks. This paper describes that the HGN's pattern matching capability and the small response time remain insensitive to the increases in the number of stored patterns. Moreover, the HGN does not require definition of rules or setting of thresholds by the operator to achieve the desired results nor does it require heuristics entailing iterative operations for memorization and recall of patterns.

A Fourier transform with speed improvements for microprocessor applications

NASA Technical Reports Server (NTRS)

Lokerson, D. C.; Rochelle, R.

1980-01-01

A fast Fourier transform algorithm for the RCA 1802microprocessor was developed for spacecraft instrument applications. The computations were tailored for the restrictions an eight bit machine imposes. The algorithm incorporates some aspects of Walsh function sequency to improve operational speed. This method uses a register to add a value proportional to the period of the band being processed before each computation is to be considered. If the result overflows into the DF register, the data sample is used in computation; otherwise computation is skipped. This operation is repeated for each of the 64 data samples. This technique is used for both sine and cosine portions of the computation. The processing uses eight bit data, but because of the many computations that can increase the size of the coefficient, floating point form is used. A method to reduce the alias problem in the lower bands is also described.

Application of supercomputers to computational aerodynamics

NASA Technical Reports Server (NTRS)

Peterson, V. L.

1984-01-01

Computers are playing an increasingly important role in the field of aerodynamics such that they now serve as a major complement to wind tunnels in aerospace research and development. Factors pacing advances in computational aerodynamics are identified, including the amount of computational power required to take the next major step in the discipline. Example results obtained from the successively refined forms of the governing equations are discussed, both in the context of levels of computer power required and the degree to which they either further the frontiers of research or apply to problems of practical importance. Finally, the Numerical Aerodynamic Simulation (NAS) Program - with its 1988 target of achieving a sustained computational rate of 1 billion floating point operations per second and operating with a memory of 240 million words - is discussed in terms of its goals and its projected effect on the future of computational aerodynamics.

A new event detector designed for the Seismic Research Observatories

USGS Publications Warehouse

Murdock, James N.; Hutt, Charles R.

1983-01-01

A new short-period event detector has been implemented on the Seismic Research Observatories. For each signal detected, a printed output gives estimates of the time of onset of the signal, direction of the first break, quality of onset, period and maximum amplitude of the signal, and an estimate of the variability of the background noise. On the SRO system, the new algorithm runs ~2.5x faster than the former (power level) detector. This increase in speed is due to the design of the algorithm: all operations can be performed by simple shifts, additions, and comparisons (floating point operations are not required). Even though a narrow-band recursive filter is not used, the algorithm appears to detect events competitively with those algorithms that employ such filters. Tests at Albuquerque Seismological Laboratory on data supplied by Blandford suggest performance commensurate with the on-line detector of the Seismic Data Analysis Center, Alexandria, Virginia.

33 CFR 161.18 - Reporting requirements.

Code of Federal Regulations, 2010 CFR

2010-07-01

... call. H HOTEL Date, time and point of entry system Entry time expressed as in (B) and into the entry... KILO Date, time and point of exit from system Exit time expressed as in (B) and exit position expressed....; for a dredge or floating plant: configuration of pipeline, mooring configuration, number of assist...

U. S. Naval Forces, Vietnam Monthly Historical Summary for July 1970

DTIC Science & Technology

1970-09-22

o o- e ... " ......... CURRENT OPERATIONS ......... ............ I* USN OPERATIONS .7 - Operation Sea Float / Tran I-Tung Dao III...Fleet 21......................... .............. 19 VNN OPERATIONS . Tran Hung Dao I............ .................... 21 Tran Hung Dao II...24 Tran Hung Dao V .................................... 28Tran Hung Dao XI 30 Tran Hung Dao XII (Special Operation

A Spaceborne Synthetic Aperture Radar Partial Fixed-Point Imaging System Using a Field- Programmable Gate Array—Application-Specific Integrated Circuit Hybrid Heterogeneous Parallel Acceleration Technique

PubMed Central

Li, Bingyi; Chen, Liang; Wei, Chunpeng; Xie, Yizhuang; Chen, He; Yu, Wenyue

2017-01-01

With the development of satellite load technology and very large scale integrated (VLSI) circuit technology, onboard real-time synthetic aperture radar (SAR) imaging systems have become a solution for allowing rapid response to disasters. A key goal of the onboard SAR imaging system design is to achieve high real-time processing performance with severe size, weight, and power consumption constraints. In this paper, we analyse the computational burden of the commonly used chirp scaling (CS) SAR imaging algorithm. To reduce the system hardware cost, we propose a partial fixed-point processing scheme. The fast Fourier transform (FFT), which is the most computation-sensitive operation in the CS algorithm, is processed with fixed-point, while other operations are processed with single precision floating-point. With the proposed fixed-point processing error propagation model, the fixed-point processing word length is determined. The fidelity and accuracy relative to conventional ground-based software processors is verified by evaluating both the point target imaging quality and the actual scene imaging quality. As a proof of concept, a field- programmable gate array—application-specific integrated circuit (FPGA-ASIC) hybrid heterogeneous parallel accelerating architecture is designed and realized. The customized fixed-point FFT is implemented using the 130 nm complementary metal oxide semiconductor (CMOS) technology as a co-processor of the Xilinx xc6vlx760t FPGA. A single processing board requires 12 s and consumes 21 W to focus a 50-km swath width, 5-m resolution stripmap SAR raw data with a granularity of 16,384 × 16,384. PMID:28672813

A Spaceborne Synthetic Aperture Radar Partial Fixed-Point Imaging System Using a Field- Programmable Gate Array-Application-Specific Integrated Circuit Hybrid Heterogeneous Parallel Acceleration Technique.

PubMed

Yang, Chen; Li, Bingyi; Chen, Liang; Wei, Chunpeng; Xie, Yizhuang; Chen, He; Yu, Wenyue

2017-06-24

With the development of satellite load technology and very large scale integrated (VLSI) circuit technology, onboard real-time synthetic aperture radar (SAR) imaging systems have become a solution for allowing rapid response to disasters. A key goal of the onboard SAR imaging system design is to achieve high real-time processing performance with severe size, weight, and power consumption constraints. In this paper, we analyse the computational burden of the commonly used chirp scaling (CS) SAR imaging algorithm. To reduce the system hardware cost, we propose a partial fixed-point processing scheme. The fast Fourier transform (FFT), which is the most computation-sensitive operation in the CS algorithm, is processed with fixed-point, while other operations are processed with single precision floating-point. With the proposed fixed-point processing error propagation model, the fixed-point processing word length is determined. The fidelity and accuracy relative to conventional ground-based software processors is verified by evaluating both the point target imaging quality and the actual scene imaging quality. As a proof of concept, a field- programmable gate array-application-specific integrated circuit (FPGA-ASIC) hybrid heterogeneous parallel accelerating architecture is designed and realized. The customized fixed-point FFT is implemented using the 130 nm complementary metal oxide semiconductor (CMOS) technology as a co-processor of the Xilinx xc6vlx760t FPGA. A single processing board requires 12 s and consumes 21 W to focus a 50-km swath width, 5-m resolution stripmap SAR raw data with a granularity of 16,384 × 16,384.

Unsteady aerodynamic analysis for offshore floating wind turbines under different wind conditions.

PubMed

Xu, B F; Wang, T G; Yuan, Y; Cao, J F

2015-02-28

A free-vortex wake (FVW) model is developed in this paper to analyse the unsteady aerodynamic performance of offshore floating wind turbines. A time-marching algorithm of third-order accuracy is applied in the FVW model. Owing to the complex floating platform motions, the blade inflow conditions and the positions of initial points of vortex filaments, which are different from the fixed wind turbine, are modified in the implemented model. A three-dimensional rotational effect model and a dynamic stall model are coupled into the FVW model to improve the aerodynamic performance prediction in the unsteady conditions. The effects of floating platform motions in the simulation model are validated by comparison between calculation and experiment for a small-scale rigid test wind turbine coupled with a floating tension leg platform (TLP). The dynamic inflow effect carried by the FVW method itself is confirmed and the results agree well with the experimental data of a pitching transient on another test turbine. Also, the flapping moment at the blade root in yaw on the same test turbine is calculated and compares well with the experimental data. Then, the aerodynamic performance is simulated in a yawed condition of steady wind and in an unyawed condition of turbulent wind, respectively, for a large-scale wind turbine coupled with the floating TLP motions, demonstrating obvious differences in rotor performance and blade loading from the fixed wind turbine. The non-dimensional magnitudes of loading changes due to the floating platform motions decrease from the blade root to the blade tip. © 2015 The Author(s) Published by the Royal Society. All rights reserved.

Unsteady aerodynamic analysis for offshore floating wind turbines under different wind conditions

PubMed Central

Xu, B. F.; Wang, T. G.; Yuan, Y.; Cao, J. F.

2015-01-01

A free-vortex wake (FVW) model is developed in this paper to analyse the unsteady aerodynamic performance of offshore floating wind turbines. A time-marching algorithm of third-order accuracy is applied in the FVW model. Owing to the complex floating platform motions, the blade inflow conditions and the positions of initial points of vortex filaments, which are different from the fixed wind turbine, are modified in the implemented model. A three-dimensional rotational effect model and a dynamic stall model are coupled into the FVW model to improve the aerodynamic performance prediction in the unsteady conditions. The effects of floating platform motions in the simulation model are validated by comparison between calculation and experiment for a small-scale rigid test wind turbine coupled with a floating tension leg platform (TLP). The dynamic inflow effect carried by the FVW method itself is confirmed and the results agree well with the experimental data of a pitching transient on another test turbine. Also, the flapping moment at the blade root in yaw on the same test turbine is calculated and compares well with the experimental data. Then, the aerodynamic performance is simulated in a yawed condition of steady wind and in an unyawed condition of turbulent wind, respectively, for a large-scale wind turbine coupled with the floating TLP motions, demonstrating obvious differences in rotor performance and blade loading from the fixed wind turbine. The non-dimensional magnitudes of loading changes due to the floating platform motions decrease from the blade root to the blade tip. PMID:25583859

An Evaluation of Pixel-Based Methods for the Detection of Floating Objects on the Sea Surface

NASA Astrophysics Data System (ADS)

Borghgraef, Alexander; Barnich, Olivier; Lapierre, Fabian; Van Droogenbroeck, Marc; Philips, Wilfried; Acheroy, Marc

2010-12-01

Ship-based automatic detection of small floating objects on an agitated sea surface remains a hard problem. Our main concern is the detection of floating mines, which proved a real threat to shipping in confined waterways during the first Gulf War, but applications include salvaging, search-and-rescue operation, perimeter, or harbour defense. Detection in infrared (IR) is challenging because a rough sea is seen as a dynamic background of moving objects with size order, shape, and temperature similar to those of the floating mine. In this paper we have applied a selection of background subtraction algorithms to the problem, and we show that the recent algorithms such as ViBe and behaviour subtraction, which take into account spatial and temporal correlations within the dynamic scene, significantly outperform the more conventional parametric techniques, with only little prior assumptions about the physical properties of the scene.

STS-26 Pilot Covey floats in life raft during JSC WETF exercises

NASA Image and Video Library

1988-07-08

S88-42425 (20 July 1988) --- STS-26 Discovery, Orbiter Vehicle (OV) 103, Pilot Richard O. Covey, wearing the newly designed launch and entry suit (LES), floats in single-occupant life raft in JSC Weightless Environment Training Facility (WETF) Bldg 29 pool. The simulation of the escape and rescue operations utilized the crew escape system (CES) pole method of egress from the Space Shuttle.

STS-26 Pilot Covey floats in life raft during JSC WETF exercises

NASA Technical Reports Server (NTRS)

1988-01-01

STS-26 Discovery, Orbiter Vehicle (OV) 103, Pilot Richard O. Covey, wearing the newly designed launch and entry suit (LES), floats in single-occupant life raft in JSC Weightless Environment Training Facility (WETF) Bldg 29 pool. Covey has paddle-like gloves on his hands. The simulation of the escape and rescue operations utilized the crew escape system (CES) pole method of egress from the Space Shuttle.

Floating liquid phase in sedimenting colloid-polymer mixtures.

PubMed

Schmidt, Matthias; Dijkstra, Marjolein; Hansen, Jean-Pierre

2004-08-20

Density functional theory and computer simulation are used to investigate sedimentation equilibria of colloid-polymer mixtures within the Asakura-Oosawa-Vrij model of hard sphere colloids and ideal polymers. When the ratio of buoyant masses of the two species is comparable to the ratio of differences in density of the coexisting bulk (colloid) gas and liquid phases, a stable "floating liquid" phase is found, i.e., a thin layer of liquid sandwiched between upper and lower gas phases. The full phase diagram of the mixture under gravity shows coexistence of this floating liquid phase with a single gas phase or a phase involving liquid-gas equilibrium; the phase coexistence lines meet at a triple point. This scenario remains valid for general asymmetric binary mixtures undergoing bulk phase separation.

Floating microbial fuel cells as energy harvesters for signal transmission from natural water bodies

NASA Astrophysics Data System (ADS)

Schievano, Andrea; Colombo, Alessandra; Grattieri, Matteo; Trasatti, Stefano P.; Liberale, Alessandro; Tremolada, Paolo; Pino, Claudio; Cristiani, Pierangela

2017-02-01

A new type of floating microbial fuel cell (fMFC) was developed for power supply of remote environmental sensors and data transmission. Ten operating fMFCs generated a cell potential in the range 100-800 mV depending on the external resistance applied. Power production peaked around 3-3.5 mW (power density of 22-28 mW m-2 cathode) after about 20-30 days of start-up period. The average of daily electrical energy harvested ranged between 10 and 35 mWh/d. Long-term performances were ensured in the presence of dense rice plants (Oryza Sativa). A power management system, based on a step-up DC/DC converter and a low-power data transmission system via SIGFOX™ technology, have been set up for the fMFCs. The tested fMFCs systems allowed to: i) harvest produced energy, ii) supply electronic devices (intermittent LED-light and a buzzer); iii) transmit remote data at low speed (three message of 12 bites each, in 6 s). Several 'floating garden' MFCs were set in the context of demonstrative events at EXPO2015 world exposition held in Milan between May-October 2015. Some of the 'floating garden' MFCs were operating for more than one year.

Floating Oscillator-Embedded Triboelectric Generator for Versatile Mechanical Energy Harvesting

PubMed Central

Seol, Myeong-Lok; Han, Jin-Woo; Jeon, Seung-Bae; Meyyappan, M.; Choi, Yang-Kyu

2015-01-01

A versatile vibration energy harvesting platform based on a triboelectricity is proposed and analyzed. External mechanical vibration repeats an oscillating motion of a polymer-coated metal oscillator floating inside a surrounding tube. Continuous sidewall friction at the contact interface of the oscillator induces current between the inner oscillator electrode and the outer tube electrode to convert mechanical vibrations into electrical energy. The floating oscillator-embedded triboelectric generator (FO-TEG) is applicable for both impulse excitation and sinusoidal vibration which universally exist in usual environment. For the impulse excitation, the generated current sustains and slowly decays by the residual oscillation of the floating oscillator. For the sinusoidal vibration, the output energy can be maximized by resonance oscillation. The operating frequency range can be simply optimized with high degree of freedom to satisfy various application requirements. In addition, the excellent immunity against ambient humidity is experimentally demonstrated, which stems from the inherently packaged structure of FO-TEG. The prototype device provides a peak-to-peak open-circuit voltage of 157 V and instantaneous short-circuit current of 4.6 μA, within sub-10 Hz of operating frequency. To visually demonstrate the energy harvesting behavior of FO-TEG, lighting of an array of LEDs is demonstrated using artificial vibration and human running. PMID:26553524

Floating Oscillator-Embedded Triboelectric Generator for Versatile Mechanical Energy Harvesting.

PubMed

Seol, Myeong-Lok; Han, Jin-Woo; Jeon, Seung-Bae; Meyyappan, M; Choi, Yang-Kyu

2015-11-10

A versatile vibration energy harvesting platform based on a triboelectricity is proposed and analyzed. External mechanical vibration repeats an oscillating motion of a polymer-coated metal oscillator floating inside a surrounding tube. Continuous sidewall friction at the contact interface of the oscillator induces current between the inner oscillator electrode and the outer tube electrode to convert mechanical vibrations into electrical energy. The floating oscillator-embedded triboelectric generator (FO-TEG) is applicable for both impulse excitation and sinusoidal vibration which universally exist in usual environment. For the impulse excitation, the generated current sustains and slowly decays by the residual oscillation of the floating oscillator. For the sinusoidal vibration, the output energy can be maximized by resonance oscillation. The operating frequency range can be simply optimized with high degree of freedom to satisfy various application requirements. In addition, the excellent immunity against ambient humidity is experimentally demonstrated, which stems from the inherently packaged structure of FO-TEG. The prototype device provides a peak-to-peak open-circuit voltage of 157 V and instantaneous short-circuit current of 4.6 μA, within sub-10 Hz of operating frequency. To visually demonstrate the energy harvesting behavior of FO-TEG, lighting of an array of LEDs is demonstrated using artificial vibration and human running.

Research on the influence of helical strakes on dynamic response of floating wind turbine platform

NASA Astrophysics Data System (ADS)

Ding, Qin-wei; Li, Chun

2017-04-01

The stability of platform structure is the paramount guarantee of the safe operation of the offshore floating wind turbine. The NREL 5MW floating wind turbine is established based on the OC3-Hywind Spar Buoy platform with the supplement of helical strakes for the purpose to analyze the impact of helical strakes on the dynamic response of the floating wind turbine Spar platform. The dynamic response of floating wind turbine Spar platform under wind, wave and current loading from the impact of number, height and pitch ratio of the helical strakes is analysed by the radiation and diffraction theory, the finite element method and orthogonal design method. The result reveals that the helical strakes can effectively inhibit the dynamic response of the platform but enlarge the wave exciting force; the best parameter combination is two pieces of helical strakes with the height of 15% D ( D is the diameter of the platform) and the pitch ratio of 5; the height of the helical strake and its pitch ratio have significant influence on pitch response.

Potential of water surface-floating microalgae for biodiesel production: Floating-biomass and lipid productivities.

PubMed

Muto, Masaki; Nojima, Daisuke; Yue, Liang; Kanehara, Hideyuki; Naruse, Hideaki; Ujiro, Asuka; Yoshino, Tomoko; Matsunaga, Tadashi; Tanaka, Tsuyoshi

2017-03-01

Microalgae have been accepted as a promising feedstock for biodiesel production owing to their capability of converting solar energy into lipids through photosynthesis. However, the high capital and operating costs, and high energy consumption, are hampering commercialization of microalgal biodiesel. In this study, the surface-floating microalga, strain AVFF007 (tentatively identified as Botryosphaerella sudetica), which naturally forms a biofilm on surfaces, was characterized for use in biodiesel production. The biofilm could be conveniently harvested from the surface of the water by adsorbing onto a polyethylene film. The lipid productivity of strain AVFF007 was 46.3 mg/L/day, allowing direct comparison to lipid productivities of other microalgal species. The moisture content of the surface-floating biomass was 86.0 ± 1.2%, which was much lower than that of the biomass harvested using centrifugation. These results reveal the potential of this surface-floating microalgal species as a biodiesel producer, employing a novel biomass harvesting and dewatering strategy. Copyright © 2016 The Society for Biotechnology, Japan. Published by Elsevier B.V. All rights reserved.

RT11LIB: a library of subroutines for transferring data between a PDP-11 and CDC-6600

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jones, H.D.

1978-01-01

RT11LIB is a library of subroutines available to CDC 6600 users for the purpose of transferring data or program listings between a PDP-11 and a CDC 6600. These subroutines, operating on a CDC 6600 under the NOS/BE or SCOPE 3.4 operating systems, read or write magnetic tapes that are compatible with the PDP-11's RT11 operating system. Data written on the tape by the PDP-11 can be read by these subroutines and then translated into CDC 6600 format for subsequent data analysis. The translation process provides for many data formats, including byte, integer, floating point, and character string formats. Alternatively, datamore » from the CDC 6600 can be translated into PDP-11 format then written onto the tape for subsequent use on the PDP-11. This facility allows a program punched on a card deck by a keypunch operator to be transferred to the PDP-11, even though the PDP-11 is not itself equipped with a card reader.« less

Expressions Module for the Satellite Orbit Analysis Program

NASA Technical Reports Server (NTRS)

Edmonds, Karina

2008-01-01

The Expressions Module is a software module that has been incorporated into the Satellite Orbit Analysis Program (SOAP). The module includes an expressions- parser submodule built on top of an analytical system, enabling the user to define logical and numerical variables and constants. The variables can capture output from SOAP orbital-prediction and geometric-engine computations. The module can combine variables and constants with built-in logical operators (such as Boolean AND, OR, and NOT), relational operators (such as >, <, or =), and mathematical operators (such as addition, subtraction, multiplication, division, modulus, exponentiation, differentiation, and integration). Parentheses can be used to specify precedence of operations. The module contains a library of mathematical functions and operations, including logarithms, trigonometric functions, Bessel functions, minimum/ maximum operations, and floating- point-to-integer conversions. The module supports combinations of time, distance, and angular units and has a dimensional- analysis component that checks for correct usage of units. A parser based on the Flex language and the Bison program looks for and indicates errors in syntax. SOAP expressions can be built using other expressions as arguments, thus enabling the user to build analytical trees. A graphical user interface facilitates use.

Mistaken Identifiers: Gene name errors can be introduced inadvertently when using Excel in bioinformatics

PubMed Central

Zeeberg, Barry R; Riss, Joseph; Kane, David W; Bussey, Kimberly J; Uchio, Edward; Linehan, W Marston; Barrett, J Carl; Weinstein, John N

2004-01-01

Background When processing microarray data sets, we recently noticed that some gene names were being changed inadvertently to non-gene names. Results A little detective work traced the problem to default date format conversions and floating-point format conversions in the very useful Excel program package. The date conversions affect at least 30 gene names; the floating-point conversions affect at least 2,000 if Riken identifiers are included. These conversions are irreversible; the original gene names cannot be recovered. Conclusions Users of Excel for analyses involving gene names should be aware of this problem, which can cause genes, including medically important ones, to be lost from view and which has contaminated even carefully curated public databases. We provide work-arounds and scripts for circumventing the problem. PMID:15214961

Renormalization group procedure for potential -g/r2

NASA Astrophysics Data System (ADS)

Dawid, S. M.; Gonsior, R.; Kwapisz, J.; Serafin, K.; Tobolski, M.; Głazek, S. D.

2018-02-01

Schrödinger equation with potential - g /r2 exhibits a limit cycle, described in the literature in a broad range of contexts using various regularizations of the singularity at r = 0. Instead, we use the renormalization group transformation based on Gaussian elimination, from the Hamiltonian eigenvalue problem, of high momentum modes above a finite, floating cutoff scale. The procedure identifies a richer structure than the one we found in the literature. Namely, it directly yields an equation that determines the renormalized Hamiltonians as functions of the floating cutoff: solutions to this equation exhibit, in addition to the limit-cycle, also the asymptotic-freedom, triviality, and fixed-point behaviors, the latter in vicinity of infinitely many separate pairs of fixed points in different partial waves for different values of g.

Program Correctness, Verification and Testing for Exascale (Corvette)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sen, Koushik; Iancu, Costin; Demmel, James W

The goal of this project is to provide tools to assess the correctness of parallel programs written using hybrid parallelism. There is a dire lack of both theoretical and engineering know-how in the area of finding bugs in hybrid or large scale parallel programs, which our research aims to change. In the project we have demonstrated novel approaches in several areas: 1. Low overhead automated and precise detection of concurrency bugs at scale. 2. Using low overhead bug detection tools to guide speculative program transformations for performance. 3. Techniques to reduce the concurrency required to reproduce a bug using partialmore » program restart/replay. 4. Techniques to provide reproducible execution of floating point programs. 5. Techniques for tuning the floating point precision used in codes.« less

Floating Gate CMOS Dosimeter With Frequency Output

NASA Astrophysics Data System (ADS)

Garcia-Moreno, E.; Isern, E.; Roca, M.; Picos, R.; Font, J.; Cesari, J.; Pineda, A.

2012-04-01

This paper presents a gamma radiation dosimeter based on a floating gate sensor. The sensor is coupled with a signal processing circuitry, which furnishes a square wave output signal, the frequency of which depends on the total dose. Like any other floating gate dosimeter, it exhibits zero bias operation and reprogramming capabilities. The dosimeter has been designed in a standard 0.6 m CMOS technology. The whole dosimeter occupies a silicon area of 450 m250 m. The initial sensitivity to a radiation dose is Hz/rad, and to temperature and supply voltage is kHz/°C and 0.067 kHz/mV, respectively. The lowest detectable dose is less than 1 rad.

33 CFR 183.110 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

..., below a height of 4 inches measured from the lowest point in the boat where liquid can collect when the boat is in its static floating position, except engine rooms. Connected means allowing a flow of water... the engine room or a connected compartment below a height of 12 inches measured from the lowest point...

33 CFR 110.60 - Captain of the Port, New York.

Code of Federal Regulations, 2011 CFR

2011-07-01

... yachts and other recreational craft. A mooring buoy is permitted. (4) Manhattan, Fort Washington Point... special anchorage area is principally for use by yachts and other recreational craft. A temporary float or... shoreline to the point of origin. Note to paragraph (d)(5): The area will be principally for use by yachts...

The floating shoulder.

PubMed

Owens, B D; Goss, T P

2006-11-01

The floating shoulder is defined as ipsilateral fractures of the midshaft of the clavicle and the neck of the glenoid. This rare injury can be difficult to manage without a thorough understanding of the complex anatomy of the shoulder girdle. Surgical intervention needs to be considered for all of these injuries. While acceptable results can be expected with non-operative management of minimally-displaced fractures, displacement at one or both sites is best managed with surgical reduction and fixation.

STS-26 Pilot Covey floats in life raft during JSC WETF exercises

NASA Technical Reports Server (NTRS)

1988-01-01

STS-26 Discovery, Orbiter Vehicle (OV) 103, Pilot Richard O. Covey, wearing the newly designed launch and entry suit (LES), floats in single-occupant life raft in JSC Weightless Environment Training Facility (WETF) Bldg 29 pool. Covey pulls and fastens life raft protective cover over himself. The simulation of the escape and rescue operations utilized the crew escape system (CES) pole method of egress from the Space Shuttle.

Geographic Resources Analysis Support System (GRASS) Version 4.0 User’s Reference Manual

DTIC Science & Technology

1992-06-01

inpur-image need not be square; before processing, the X and Y dimensions of the input-image are padded with zeroes to the next highest power of two in...structures an input kowledge /control script with an appropriate combination of map layer category values (GRASS raster map layers that contain data on...F cos(x) cosine of x (x is in degrees) F exp(x) exponential function of x F exp(x,y) x to the power y F float(x) convert x to floating point F if

Basic mathematical function libraries for scientific computation

NASA Technical Reports Server (NTRS)

Galant, David C.

1989-01-01

Ada packages implementing selected mathematical functions for the support of scientific and engineering applications were written. The packages provide the Ada programmer with the mathematical function support found in the languages Pascal and FORTRAN as well as an extended precision arithmetic and a complete complex arithmetic. The algorithms used are fully described and analyzed. Implementation assumes that the Ada type FLOAT objects fully conform to the IEEE 754-1985 standard for single binary floating-point arithmetic, and that INTEGER objects are 32-bit entities. Codes for the Ada packages are included as appendixes.

Fine-grained parallelization of fitness functions in bioinformatics optimization problems: gene selection for cancer classification and biclustering of gene expression data.

PubMed

Gomez-Pulido, Juan A; Cerrada-Barrios, Jose L; Trinidad-Amado, Sebastian; Lanza-Gutierrez, Jose M; Fernandez-Diaz, Ramon A; Crawford, Broderick; Soto, Ricardo

2016-08-31

Metaheuristics are widely used to solve large combinatorial optimization problems in bioinformatics because of the huge set of possible solutions. Two representative problems are gene selection for cancer classification and biclustering of gene expression data. In most cases, these metaheuristics, as well as other non-linear techniques, apply a fitness function to each possible solution with a size-limited population, and that step involves higher latencies than other parts of the algorithms, which is the reason why the execution time of the applications will mainly depend on the execution time of the fitness function. In addition, it is usual to find floating-point arithmetic formulations for the fitness functions. This way, a careful parallelization of these functions using the reconfigurable hardware technology will accelerate the computation, specially if they are applied in parallel to several solutions of the population. A fine-grained parallelization of two floating-point fitness functions of different complexities and features involved in biclustering of gene expression data and gene selection for cancer classification allowed for obtaining higher speedups and power-reduced computation with regard to usual microprocessors. The results show better performances using reconfigurable hardware technology instead of usual microprocessors, in computing time and power consumption terms, not only because of the parallelization of the arithmetic operations, but also thanks to the concurrent fitness evaluation for several individuals of the population in the metaheuristic. This is a good basis for building accelerated and low-energy solutions for intensive computing scenarios.

Production and aging of paramagnetic point defects in P-doped floating zone silicon irradiated with high fluence 27 MeV electrons

NASA Astrophysics Data System (ADS)

Joita, A. C.; Nistor, S. V.

2018-04-01

Enhancing the long term stable performance of silicon detectors used for monitoring the position and flux of the particle beams in high energy physics experiments requires a better knowledge of the nature, stability, and transformation properties of the radiation defects created over the operation time. We report the results of an electron spin resonance investigation in the nature, transformation, and long term stability of the irradiation paramagnetic point defects (IPPDs) produced by high fluence (2 × 1016 cm-2), high energy (27 MeV) electrons in n-type, P-doped standard floating zone silicon. We found out that both freshly irradiated and aged (i.e., stored after irradiation for 3.5 years at 250 K) samples mainly contain negatively charged tetravacancy and pentavacancy defects in the first case and tetravacancy defects in the second one. The fact that such small cluster vacancy defects have not been observed by irradiation with low energy (below 5 MeV) electrons, but were abundantly produced by irradiation with neutrons, strongly suggests the presence of the same mechanism of direct formation of small vacancy clusters by irradiation with neutrons and high energy, high fluence electrons, in agreement with theoretical predictions. Differences in the nature and annealing properties of the IPPDs observed between the 27 MeV electrons freshly irradiated, and irradiated and aged samples were attributed to the presence of a high concentration of divacancies in the freshly irradiated samples, defects which transform during storage at 250 K through diffusion and recombination processes.

Spaceborne Imaging Radar-C instrument

NASA Technical Reports Server (NTRS)

Huneycutt, Bryan L.

1993-01-01

The Spaceborne Imaging Radar-C is the next radar in the series of spaceborne radar experiments, which began with Seasat and continued with SIR-A and SIR-B. The SIR-C instrument has been designed to obtain simultaneous multifrequency and simultaneous multipolarization radar images from a low earth orbit. It is a multiparameter imaging radar that will be flown during at least two different seasons. The instrument operates in the squint alignment mode, the extended aperture mode, the scansar mode, and the interferometry mode. The instrument uses engineering techniques such as beam nulling for echo tracking, pulse repetition frequency hopping for Doppler centroid tracking, generating the frequency step chirp for radar parameter flexibility, block floating-point quantizing for data rate compression, and elevation beamwidth broadening for increasing the swath illumination.

Speech coding at 4800 bps for mobile satellite communications

NASA Technical Reports Server (NTRS)

Gersho, Allen; Chan, Wai-Yip; Davidson, Grant; Chen, Juin-Hwey; Yong, Mei

1988-01-01

A speech compression project has recently been completed to develop a speech coding algorithm suitable for operation in a mobile satellite environment aimed at providing telephone quality natural speech at 4.8 kbps. The work has resulted in two alternative techniques which achieve reasonably good communications quality at 4.8 kbps while tolerating vehicle noise and rather severe channel impairments. The algorithms are embodied in a compact self-contained prototype consisting of two AT and T 32-bit floating-point DSP32 digital signal processors (DSP). A Motorola 68HC11 microcomputer chip serves as the board controller and interface handler. On a wirewrapped card, the prototype's circuit footprint amounts to only 200 sq cm, and consumes about 9 watts of power.

Advances in petascale kinetic plasma simulation with VPIC and Roadrunner

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bowers, Kevin J; Albright, Brian J; Yin, Lin

2009-01-01

VPIC, a first-principles 3d electromagnetic charge-conserving relativistic kinetic particle-in-cell (PIC) code, was recently adapted to run on Los Alamos's Roadrunner, the first supercomputer to break a petaflop (10{sup 15} floating point operations per second) in the TOP500 supercomputer performance rankings. They give a brief overview of the modeling capabilities and optimization techniques used in VPIC and the computational characteristics of petascale supercomputers like Roadrunner. They then discuss three applications enabled by VPIC's unprecedented performance on Roadrunner: modeling laser plasma interaction in upcoming inertial confinement fusion experiments at the National Ignition Facility (NIF), modeling short pulse laser GeV ion acceleration andmore » modeling reconnection in magnetic confinement fusion experiments.« less

Development of a 32-bit UNIX-based ELAS workstation

NASA Technical Reports Server (NTRS)

Spiering, Bruce A.; Pearson, Ronnie W.; Cheng, Thomas D.

1987-01-01

A mini/microcomputer UNIX-based image analysis workstation has been designed and is being implemented to use the Earth Resources Laboratory Applications Software (ELAS). The hardware system includes a MASSCOMP 5600 computer, which is a 32-bit UNIX-based system (compatible with AT&T System V and Berkeley 4.2 BSD operating system), a floating point accelerator, a 474-megabyte fixed disk, a tri-density magnetic tape drive, and an 1152 by 910 by 12-plane color graphics/image interface. The software conversion includes reconfiguring the ELAs driver Master Task, recompiling and then testing the converted application modules. This hardware and software configuration is a self-sufficient image analysis workstation which can be used as a stand-alone system, or networked with other compatible workstations.

Computations of unsteady multistage compressor flows in a workstation environment

NASA Technical Reports Server (NTRS)

Gundy-Burlet, Karen L.

1992-01-01

High-end graphics workstations are becoming a necessary tool in the computational fluid dynamics environment. In addition to their graphic capabilities, workstations of the latest generation have powerful floating-point-operation capabilities. As workstations become common, they could provide valuable computing time for such applications as turbomachinery flow calculations. This report discusses the issues involved in implementing an unsteady, viscous multistage-turbomachinery code (STAGE-2) on workstations. It then describes work in which the workstation version of STAGE-2 was used to study the effects of axial-gap spacing on the time-averaged and unsteady flow within a 2 1/2-stage compressor. The results included time-averaged surface pressures, time-averaged pressure contours, standard deviation of pressure contours, pressure amplitudes, and force polar plots.

A performance comparison of the Cray-2 and the Cray X-MP

NASA Technical Reports Server (NTRS)

Schmickley, Ronald; Bailey, David H.

1986-01-01

A suite of thirteen large Fortran benchmark codes were run on Cray-2 and Cray X-MP supercomputers. These codes were a mix of compute-intensive scientific application programs (mostly Computational Fluid Dynamics) and some special vectorized computation exercise programs. For the general class of programs tested on the Cray-2, most of which were not specially tuned for speed, the floating point operation rates varied under a variety of system load configurations from 40 percent up to 125 percent of X-MP performance rates. It is concluded that the Cray-2, in the original system configuration studied (without memory pseudo-banking) will run untuned Fortran code, on average, about 70 percent of X-MP speeds.

AmeriFlux US-WPT Winous Point North Marsh

DOE Data Explorer

Chen, Jiquan [University of Toledo / Michigan State University

2016-01-01

This is the AmeriFlux version of the carbon flux data for the site US-WPT Winous Point North Marsh. Site Description - The marsh site has been owned by the Winous Point Shooting Club since 1856 and has been managed by wildlife biologists since 1946. The hydrology of the marsh is relatively isolated by the surrounding dikes and drainages and only receives drainage from nearby croplands through three connecting ditches. Since 2001, the marsh has been managed to maintain year-round inundation with the lowest water levels in September. Within the 0–250 m fetch of the tower, the marsh comprises 42.9% of floating-leaved vegetation, 52.7% of emergent vegetation, and 4.4% of dike and upland during the growing season. Dominant emergent plants include narrow-leaved cattail (Typha angustifolia), rose mallow (Hibiscus moscheutos), and bur reed (Sparganium americanum). Common floating-leaved species are water lily (Nymphaea odorata) and American lotus (Nelumbo lutea) with foliage usually covering the water surface from late May to early October.

Elimination of fecal coliforms and F-specific RNA coliphage from oysters (Crassostrea virginica) relaid in floating containers.

PubMed

Kator, H; Rhodes, M

2001-06-01

Declining oyster (Crassostrea virginica) production in the Chesapeake Bay has stimulated aquaculture based on floats for off-bottom culture. While advantages of off-bottom culture are significant, the increased use of floating containers raises public health and microbiological concerns, because oysters in floats may be more susceptible to fecal contamination from storm runoff compared to those cultured on-bottom. We conducted four commercial-scale studies with market-size oysters naturally contaminated with fecal coliforms (FC) and a candidate viral indicator, F-specific RNA (FRNA) coliphage. To facilitate sampling and to test for location effects, 12 replicate subsamples, each consisting of 15 to 20 randomly selected oysters in plastic mesh bags, were placed at four characteristic locations within a 0.6- by 3.0-m "Taylor" float, and the remaining oysters were added to a depth not exceeding 15.2 cm. The float containing approximately 3,000 oysters was relaid in the York River, Virginia, for 14 days. During relay, increases in shellfish FC densities followed rain events such that final mean levels exceeded initial levels or did not meet an arbitrary product end point of 50 FC/100 ml. FRNA coliphage densities decreased to undetectable levels within 14 days (16 to 28 degrees C) in all but the last experiment, when temperatures fell between 12 and 16 degrees C. Friedman (nonparametric analysis of variance) tests performed on FC/Escherichia coli and FRNA densities indicated no differences in counts as a function of location within the float. The public health consequences of these observations are discussed, and future research and educational needs are identified.

Characteristics of a Single Float Seaplane During Take-off

NASA Technical Reports Server (NTRS)

Crowley, J W , Jr; Ronan, K M

1925-01-01

At the request of the Bureau of Aeronautics, Navy Department, the National Advisory Committee for Aeronautics at Langley Field is investigating the get-away characteristics of an N-9H, a DT-2, and an F-5l, as representing, respectively, a single float, a double float, and a boat type of seaplane. This report covers the investigation conducted on the N-9H. The results show that a single float seaplane trims aft in taking off. Until a planing condition is reached the angle of attack is about 15 degrees and is only slightly affected by controls. When planing it seeks a lower angle, but is controllable through a widening range, until at the take-off it is possible to obtain angles of 8 degrees to 15 degrees with corresponding speeds of 53 to 41 M. P. H. or about 40 per cent of the speed range. The point of greatest resistance occurs at about the highest angle of a pontoon planing angle of 9 1/2 degrees and at a water speed of 24 M. P. H.

Analysis of Static Spacecraft Floating Potential at Low Earth Orbit (LEO)

NASA Technical Reports Server (NTRS)

Herr, Joel L.; Hwang, K. S.; Wu, S. T.

1995-01-01

Spacecraft floating potential is the charge on the external surfaces of orbiting spacecraft relative to the space. Charging is caused by unequal negative and positive currents to spacecraft surfaces. The charging process continues until the accelerated particles can be collected rapidly enough to balance the currents at which point the spacecraft has reached its equilibrium or floating potential. In low inclination. Low Earth Orbit (LEO), the collection of positive ion and negative electrons. in a particular direction. are typically not equal. The level of charging required for equilibrium to be established is influenced by the characteristics of the ambient plasma environment. by the spacecraft motion, and by the geometry of the spacecraft. Using the kinetic theory, a statistical approach for studying the interaction is developed. The approach used to study the spacecraft floating potential depends on which phenomena are being applied. and on the properties of the plasma. especially the density and temperature. The results from kinetic theory derivation are applied to determine the charging level and the electric potential distribution at an infinite flat plate perpendicular to a streaming plasma using finite-difference scheme.

Current-Voltage and Floating-Potential characteristics of cylindrical emissive probes from a full-kinetic model based on the orbital motion theory

NASA Astrophysics Data System (ADS)

Chen, Xin; Sánchez-Arriaga, Gonzalo

2018-02-01

To model the sheath structure around an emissive probe with cylindrical geometry, the Orbital-Motion theory takes advantage of three conserved quantities (distribution function, transverse energy, and angular momentum) to transform the stationary Vlasov-Poisson system into a single integro-differential equation. For a stationary collisionless unmagnetized plasma, this equation describes self-consistently the probe characteristics. By solving such an equation numerically, parametric analyses for the current-voltage (IV) and floating-potential (FP) characteristics can be performed, which show that: (a) for strong emission, the space-charge effects increase with probe radius; (b) the probe can float at a positive potential relative to the plasma; (c) a smaller probe radius is preferred for the FP method to determine the plasma potential; (d) the work function of the emitting material and the plasma-ion properties do not influence the reliability of the floating-potential method. Analytical analysis demonstrates that the inflection point of an IV curve for non-emitting probes occurs at the plasma potential. The flat potential is not a self-consistent solution for emissive probes.

Gulp: An Imaginatively Different Approach to Learning about Water.

ERIC Educational Resources Information Center

Baird, Colette

1997-01-01

Provides details of performances by the Floating Point Science Theater working with elementary school children about the characteristics of water. Discusses student reactions to various parts of the performances. (DDR)

36 CFR 327.3 - Vessels.

Code of Federal Regulations, 2010 CFR

2010-07-01

..., community or corporate docks, or at any fixed or permanent mooring point, may only be used for overnight... floating or stationary mooring facilities on, adjacent to, or interfering with a buoy, channel marker or...

Software For Tie-Point Registration Of SAR Data

NASA Technical Reports Server (NTRS)

Rignot, Eric; Dubois, Pascale; Okonek, Sharon; Van Zyl, Jacob; Burnette, Fred; Borgeaud, Maurice

1995-01-01

SAR-REG software package registers synthetic-aperture-radar (SAR) image data to common reference frame based on manual tie-pointing. Image data can be in binary, integer, floating-point, or AIRSAR compressed format. For example, with map of soil characteristics, vegetation map, digital elevation map, or SPOT multispectral image, as long as user can generate binary image to be used by tie-pointing routine and data are available in one of the previously mentioned formats. Written in FORTRAN 77.

30 CFR 250.431 - What are the diverter design and installation requirements?

Code of Federal Regulations, 2011 CFR

2011-07-01

... ENFORCEMENT, DEPARTMENT OF THE INTERIOR OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Oil and Gas Drilling Operations Diverter System Requirements § 250.431 What are the diverter... wellhead configurations and at least 12 inches for floating drilling operations; (b) Use dual diverter...

Experimental and numerical investigation of the roll motion behavior of a floating liquefied natural gas system

NASA Astrophysics Data System (ADS)

Zhao, WenHua; Yang, JianMin; Hu, ZhiQiang; Xiao, LongFei; Peng, Tao

2013-03-01

The present paper does an experimental and numerical investigation of the hydrodynamic interaction and the response of a single point turret-moored Floating Liquefied Natural Gas (FLNG) system, which is a new type of floating LNG (Liquid Natural Gas) platform that consists of a ship-type FPSO hull equipped with LNG storage tanks and liquefaction plants. In particular, this study focuses on the investigation of the roll response of FLNG hull in free-decay motions, white noise waves and also in irregular waves. Model tests of the FLNG system in 60%H filling condition excited by both white noise waves and irregular waves combined with steady wind and current have been carried out. Response Amplitude Operators (RAOs) and time histories of the responses are obtained for sway, roll and yaw motions. Obvious Low Frequency (LF) components of the roll motions are observed, which may be out of expectation. To facilitate the physical understanding of this phenomenon, we filter the roll motions at the period of 30 s into two parts: the Wave Frequency (WF) motions and the Low Frequency (LF) motions respectively. The results indicate that the LF motions are closely related to the sway and yaw motions. Possible reasons for the presence of the LF motions of roll have been discussed in detail, through the comparison with the sway and yaw motions. As for the numerical part, the simulation of the modeled case is conducted with the help of the software SESAM®. A good agreement between experiments and calculations is reported within the scope of trends. However, the numerical simulations should be further improved for the prediction of the FLNG system in the heading sea.

[Post-stroke shoulder-hand syndrome treated with floating-needle therapy combined with rehabilitation training: a randomized controlled trial].

PubMed

Zhou, Zhao-Hui; Zhuang, Li-Xing; Chen, Zhen-Hu; Lang, Jian-Ying; Li, Yan-Hui; Jiang, Gang-Hui; Xu, Zhan-Qiong; Liao, Mu-Xi

2014-07-01

To compare the clinical efficacy in the treatment of post-stroke shoulder-hand syndrome between floating-needle therapy and conventional acupuncture on the basis of rehabilitation training. One hundred cases of post-stroke shoulder-hand syndrome were randomized into a floating-needle group and an acupuncture group, 50 cases in each one. The passive and positive rehabilitation training was adopted in the two groups. Additionally, in the floating-needle group, the floating-needle therapy was used. The needle was inserted at the site 5 to 10 cm away from myofasical trigger point (MTrP), manipulated and scattered subcutaneously, for 2 min continuously. In the acupuncture group, the conventional acupuncture was applied at Jianqian (EX-UE), Jianyu (LI 15), Jianliao (TE 14), etc. The treatment was given once every two days, 3 times a week, and 14 days of treatment were required. The shoulder hand syndrome scale (SHSS), the short form McGill pain scale (SF-MPQ) and the modified Fugl-Meyer motor function scale (FMA) were used to evaluate the damage severity, pain and motor function of the upper limbs before and after treatment in the two groups. The clinical efficacy was compared between the two groups. SHSS score, SF-MPQ score and FMA score were improved significantly after treatment in the two groups (all P < 0.01), and the improvements in the floating-needle group were superior to those in the acupuncture group (all P < 0.05). The total effective rate was 94.0% (47/50) in the floating-needle group, which was better than 90.0% (45/50) in the acupuncture group (P < 0.05). The floating-needle therapy combined with rehabilitation training achieves a satisfactory efficacy on post-stroke shoulder-hand syndrome, which is better than the combined therapy of conventional acupuncture and rehabilitation training.

Investigating the potential of floating mires as record of palaeoenvironmental changes

NASA Astrophysics Data System (ADS)

Zaccone, C.; Adamo, P.; Giordano, S.; Miano, T. M.

2012-04-01

Peat-forming floating mires could provide an exceptional resource for palaeoenvironmental and environmental monitoring studies, as much of their own history, as well as the history of their surrounds, is recorded in their peat deposits. In his Naturalis historia (AD 77-79), Pliny the Elder described floating islands on Lake Vadimonis (now Posta Fibreno Lake, Italy). Actually, a small floating island (ca. 35 m of diameter and 3 m of submerged thickness) still occurs on this calcareous lake fed by karstic springs at the base of the Apennine Mountains. Here the southernmost Italian populations of Sphagnum palustre occur on the small surface of this floating mire known as "La Rota", i.e., a cup-formed core of Sphagnum peat and rhizomes of Helophytes, erratically floating on the water-body of a submerged doline, annexed to the easternmost edge of the lake, characterised by the extension of a large reed bed. Geological evidence point out the existence in the area of a large lacustrine basin since Late Pleistocene. The progressive filling of the lake caused by changing in climatic conditions and neotectonic events, brought about the formation of peat deposits in the area, following different depositional cycles in a swampy environment. Then, a round-shaped portion of fen, originated around lake margins in waterlogged areas, was somehow isolated from the bank and started to float. Coupling data about concentrations and fluxes of several major and trace elements of different origin (i.e., dust particles, volcanic emissions, cosmogenic dusts and marine aerosols), with climate records (plant micro- and macrofossils, pollens, isotopic ratios), biomolecular records (e.g., lipids), detailed age-depth modelling (i.e., 210Pb, 137Cs, 14C), and humification indexes, the present work is hoped to identify and better understand the reliability of this particular "archive", and thus possible relationships between biogeochemical processes occurring in this floating bog and environmental changes.

[New determinations of the eye rotation center and criteria for the formation of its membrane in terms of the floating eye model and experimental support of the latter].

PubMed

Galoian, V R

1988-01-01

It is well known that the eye is a phylogenetically stabilized body with rotation properties. The eye has an elastic cover and is filled with uniform fluid. According to the theory of covers and other concepts on the configuration of turning fluid mass we concluded that the eyeball has an elliptic configuration. Classification of the eyeball is here presented with simultaneous studies of the principles of the eye situation. The parallelism between the state and different types of heterophory and orthophory was studied. To determine normal configuration it is necessary to have in mind some principles of achieving advisable correct situation of the eye in orbit. We determined the centre of the eye rotation and showed that it is impossible to situate it out of the geometrical centre of the eyeball. It was pointed out that for adequate perception the rotation centre must be situated on the visual axis. Using the well known theory of floating we experimentally determined that the centre of the eye rotation lies on the level of the floating eye, just on the point of cross of the visual line with the optical axis. It was shown experimentally on the basis of recording the eye movements in the process of eyelid closing that weakening of the eye movements is of gravitational pattern and proceeds under the action of stability forces, which directly indicates the floating state of the eye. For the first time using the model of the floating eye it was possible to show the formation of extraeye vacuum by straining the back wall. This effect can be obtained without any difficulty, if the face is turned down. The role of negative pressure in the formation of the eye ametropy, as well as new conclusions and prognostications about this new model are discussed.

Functional outcomes of "floating elbow" injuries in adult patients.

PubMed

Yokoyama, K; Itoman, M; Kobayashi, A; Shindo, M; Futami, T

1998-05-01

To assess elbow function, complications, and problems of floating elbow fractures in adults receiving surgical treatment. Retrospective clinical review. Level I trauma center in Kanagawa, Japan. Fourteen patients with fifteen floating elbow injuries, excluding one immediate amputation, seen at the Kitasato University Hospital from January 1, 1984, to April 30, 1995. All fractures were managed surgically by various methods. In ten cases, the humeral and forearm fractures were treated simultaneously with immediate fixation. In three cases, both the humeral and forearm fractures were treated with delayed fixation on Day 1, 4, or 7. In the remaining two cases, the open forearm fracture was managed with immediate fixation and the humerus fracture with delayed fixation on Day 10 or 25. All subjects underwent standardized elbow evaluations, and results were compared with an elbow score based on a 100-point scale. The parameters evaluated were pain, motion, elbow and grip strength, and function during daily activities. Complications such as infections, nonunions, malunions, and refractures were investigated. Mean follow-up was forty-three months (range 13 to 112 months). At final follow-up, the mean elbow function score was 79 points, with 67 percent (ten of fifteen) of the subjects having good or excellent results. The functional outcome did not correlate with the Injury Severity Score of the individual patients, the existence of open injuries or neurovascular injuries, or the timing of surgery. There were one deep infection, two nonunions of the humerus, two nonunions of the forearm, one varus deformity of the humerus, and one forearm refracture. Based on the present data, we could not clarify the factors influencing the final functional outcome after floating elbow injury. These injuries, however, potentially have many complications, such as infection or nonunion, especially when there is associated brachial plexus injury. We consider that floating elbow injuries are severe injuries and that surgical stabilization is needed; beyond that, there are no specific forms of surgical treatment to reliably guarantee excellent results.

30 CFR 250.907 - Where must I locate foundation boreholes?

Code of Federal Regulations, 2014 CFR

2014-07-01

... soil boring must not exceed 500 feet. (b) For deepwater floating platforms which utilize catenary or..., other points throughout the anchor pattern to establish the soil profile suitable for foundation design...

30 CFR 250.907 - Where must I locate foundation boreholes?

Code of Federal Regulations, 2013 CFR

2013-07-01

... soil boring must not exceed 500 feet. (b) For deepwater floating platforms which utilize catenary or..., other points throughout the anchor pattern to establish the soil profile suitable for foundation design...

Biliary atresia

MedlinePlus

... weight normally for the first month. After that point, the baby will lose weight and become irritable, and will have worsening jaundice. Other symptoms may include: Dark urine Enlarged spleen Floating stools Foul-smelling stools Pale or clay-colored ...

30 CFR 250.907 - Where must I locate foundation boreholes?

Code of Federal Regulations, 2012 CFR

2012-07-01

... soil boring must not exceed 500 feet. (b) For deepwater floating platforms which utilize catenary or..., other points throughout the anchor pattern to establish the soil profile suitable for foundation design...

Barriers, Obstacles, and Mine Warfare for Joint Operations

DTIC Science & Technology

2007-04-26

separated from the anchor. Mines that separate from their anchors and rise to the surface are known as floaters . These may continue to float until...the 1907 Hague Treaty, these mines have been used on occasion. A drifting mine is classified differently from a moored mine that has become a floater ...as a floater was designed to be anchored, while a drifter was designed to float freely with the tides and currents. (c) The principal advantage of

Floating gate transistors as biosensors (Conference Presentation)

NASA Astrophysics Data System (ADS)

Frisbie, C. Daniel

2016-11-01

Electrolyte gated transistors (EGTs) are a sub-class of thin film transistors that are extremely promising for biological sensing applications. These devices employ a solid electrolyte as the gate insulator; the very large capacitance of the electrolyte results in low voltage operation and high transconductance or gain. This talk will describe the fabrication of floating gate EGTs and their use as ricin sensors. The critical performance metrics for EGTs compared with other types of TFTs will also be reviewed.

Rapid Design of Gravity Assist Trajectories

NASA Technical Reports Server (NTRS)

Carrico, J.; Hooper, H. L.; Roszman, L.; Gramling, C.

1991-01-01

Several International Solar Terrestrial Physics (ISTP) missions require the design of complex gravity assisted trajectories in order to investigate the interaction of the solar wind with the Earth's magnetic field. These trajectories present a formidable trajectory design and optimization problem. The philosophy and methodology that enable an analyst to design and analyse such trajectories are discussed. The so called 'floating end point' targeting, which allows the inherently nonlinear multiple body problem to be solved with simple linear techniques, is described. The combination of floating end point targeting with analytic approximations with a Newton method targeter to achieve trajectory design goals quickly, even for the very sensitive double lunar swingby trajectories used by the ISTP missions, is demonstrated. A multiconic orbit integration scheme allows fast and accurate orbit propagation. A prototype software tool, Swingby, built for trajectory design and launch window analysis, is described.

Implementation of the DAST ARW II control laws using an 8086 microprocessor and an 8087 floating-point coprocessor. [drones for aeroelasticity research

NASA Technical Reports Server (NTRS)

Kelly, G. L.; Berthold, G.; Abbott, L.

1982-01-01

A 5 MHZ single-board microprocessor system which incorporates an 8086 CPU and an 8087 Numeric Data Processor is used to implement the control laws for the NASA Drones for Aerodynamic and Structural Testing, Aeroelastic Research Wing II. The control laws program was executed in 7.02 msec, with initialization consuming 2.65 msec and the control law loop 4.38 msec. The software emulator execution times for these two tasks were 36.67 and 61.18, respectively, for a total of 97.68 msec. The space, weight and cost reductions achieved in the present, aircraft control application of this combination of a 16-bit microprocessor with an 80-bit floating point coprocessor may be obtainable in other real time control applications.

Implementation of kernels on the Maestro processor

NASA Astrophysics Data System (ADS)

Suh, Jinwoo; Kang, D. I. D.; Crago, S. P.

Currently, most microprocessors use multiple cores to increase performance while limiting power usage. Some processors use not just a few cores, but tens of cores or even 100 cores. One such many-core microprocessor is the Maestro processor, which is based on Tilera's TILE64 processor. The Maestro chip is a 49-core, general-purpose, radiation-hardened processor designed for space applications. The Maestro processor, unlike the TILE64, has a floating point unit (FPU) in each core for improved floating point performance. The Maestro processor runs at 342 MHz clock frequency. On the Maestro processor, we implemented several widely used kernels: matrix multiplication, vector add, FIR filter, and FFT. We measured and analyzed the performance of these kernels. The achieved performance was up to 5.7 GFLOPS, and the speedup compared to single tile was up to 49 using 49 tiles.

46 CFR 117.208 - Survival craft-vessels operating on rivers routes.

Code of Federal Regulations, 2010 CFR

2010-10-01

... certificated to operate on a rivers route in cold water must be provided with life floats of an aggregate... vessel certificated to operate on a rivers route in warm water is not required to carry survival craft... carry survival craft. (d) For a vessel certificated to operate on a rivers route in shallow water where...

DOE Office of Scientific and Technical Information (OSTI.GOV)

Quon, Eliot; Platt, Andrew; Yu, Yi-Hsiang

Extreme loads are often a key cost driver for wave energy converters (WECs). As an alternative to exhaustive Monte Carlo or long-term simulations, the most likely extreme response (MLER) method allows mid- and high-fidelity simulations to be used more efficiently in evaluating WEC response to events at the edges of the design envelope, and is therefore applicable to system design analysis. The study discussed in this paper applies the MLER method to investigate the maximum heave, pitch, and surge force of a point absorber WEC. Most likely extreme waves were obtained from a set of wave statistics data based onmore » spectral analysis and the response amplitude operators (RAOs) of the floating body; the RAOs were computed from a simple radiation-and-diffraction-theory-based numerical model. A weakly nonlinear numerical method and a computational fluid dynamics (CFD) method were then applied to compute the short-term response to the MLER wave. Effects of nonlinear wave and floating body interaction on the WEC under the anticipated 100-year waves were examined by comparing the results from the linearly superimposed RAOs, the weakly nonlinear model, and CFD simulations. Overall, the MLER method was successfully applied. In particular, when coupled to a high-fidelity CFD analysis, the nonlinear fluid dynamics can be readily captured.« less

VIEW OF FACILITY NO. S 20 NEAR THE POINT WHERE ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

VIEW OF FACILITY NO. S 20 NEAR THE POINT WHERE IT JOINS FACILITY NO. S 21. NOTE THE ASPHALT-FILLED NARROW-GAUGE TRACKWAY WITH SOME AREAS OF STEEL TRACK SHOWING. VIEW FACING NORTHEAST - U.S. Naval Base, Pearl Harbor, Floating Dry Dock Quay, Hurt Avenue at northwest side of Magazine Loch, Pearl City, Honolulu County, HI

40 CFR 435.14 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2010 CFR

2010-07-01

... (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS OIL AND GAS EXTRACTION POINT SOURCE CATEGORY Offshore... 40 CFR 125.30-32, any existing point source subject to this subpart must achieve the following... Minimum of 1 mg/l and maintained as close to this concentration as possible. Sanitary M91M Floating solids...

33 CFR 183.558 - Hoses and connections.

Code of Federal Regulations, 2010 CFR

2010-07-01

...: (A) The hose is severed at the point where maximum drainage of fuel would occur, (B) The boat is in its static floating position, and (C) The fuel system is filled to the capacity market on the tank... minutes when: (A) The hose is severed at the point where maximum drainage of fuel would occur, (B) The...

Nonlinear optimization method of ship floating condition calculation in wave based on vector

NASA Astrophysics Data System (ADS)

Ding, Ning; Yu, Jian-xing

2014-08-01

Ship floating condition in regular waves is calculated. New equations controlling any ship's floating condition are proposed by use of the vector operation. This form is a nonlinear optimization problem which can be solved using the penalty function method with constant coefficients. And the solving process is accelerated by dichotomy. During the solving process, the ship's displacement and buoyant centre have been calculated by the integration of the ship surface according to the waterline. The ship surface is described using an accumulative chord length theory in order to determine the displacement, the buoyancy center and the waterline. The draught forming the waterline at each station can be found out by calculating the intersection of the ship surface and the wave surface. The results of an example indicate that this method is exact and efficient. It can calculate the ship floating condition in regular waves as well as simplify the calculation and improve the computational efficiency and the precision of results.

Experimental Study on New Multi-Column Tension-Leg-Type Floating Wind Turbine

NASA Astrophysics Data System (ADS)

Zhao, Yong-sheng; She, Xiao-he; He, Yan-ping; Yang, Jian-min; Peng, Tao; Kou, Yu-feng

2018-04-01

Deep-water regions often have winds favorable for offshore wind turbines, and floating turbines currently show the greatest potential to exploit such winds. This work established proper scaling laws for model tests, which were then implemented in the construction of a model wind turbine with optimally designed blades. The aerodynamic, hydrodynamic, and elastic characteristics of the proposed new multi-column tension-leg-type floating wind turbine (WindStar TLP system) were explored in the wave tank testing of a 1:50 scale model at the State Key Laboratory of Ocean Engineering at Shanghai Jiao Tong University. Tests were conducted under conditions of still water, white noise waves, irregular waves, and combined wind, wave, and current loads. The results established the natural periods of the motion, damping, motion response amplitude operators, and tendon tensions of the WindStar TLP system under different environmental conditions, and thus could serve as a reference for further research. Key words: floating wind turbine, model test, WindStar TLP, dynamic response

An Aeroelastic Perspective of Floating Offshore Wind Turbine Wake Formation and Instability

NASA Astrophysics Data System (ADS)

Rodriguez, Steven N.; Jaworski, Justin W.

2015-11-01

The wake formation and wake stability of floating offshore wind turbines are investigated from an aeroelastic perspective. The aeroelastic model is composed of the Sebastian-Lackner free-vortex wake aerodynamic model coupled to the nonlinear Hodges-Dowell beam equations, which are extended to include the effects of blade profile asymmetry, higher-order torsional effects, and kinetic energy components associated with periodic rigid-body motions of floating platforms. Rigid-body platform motions are also assigned to the aerodynamic model as varying inflow conditions to emulate operational rotor-wake interactions. Careful attention is given to the wake formation within operational states where the ratio of inflow velocity to induced velocity is over 50%. These states are most susceptible to aerodynamic instabilities, and provide a range of states about which a wake stability analysis can be performed. In addition, the stability analysis used for the numerical framework is implemented into a standalone free-vortex wake aerodynamic model. Both aeroelastic and standalone aerodynamic results are compared to evaluate the level of impact that flexible blades have on the wake formation and wake stability.

Floating Chip Mounting System Driven by Repulsive Force of Permanent Magnets for Multiple On-Site SPR Immunoassay Measurements

PubMed Central

Horiuchi, Tsutomu; Tobita, Tatsuya; Miura, Toru; Iwasaki, Yuzuru; Seyama, Michiko; Inoue, Suzuyo; Takahashi, Jun-ichi; Haga, Tsuneyuki; Tamechika, Emi

2012-01-01

We have developed a measurement chip installation/removal mechanism for a surface plasmon resonance (SPR) immunoassay analysis instrument designed for frequent testing, which requires a rapid and easy technique for changing chips. The key components of the mechanism are refractive index matching gel coated on the rear of the SPR chip and a float that presses the chip down. The refractive index matching gel made it possible to optically couple the chip and the prism of the SPR instrument easily via elastic deformation with no air bubbles. The float has an autonomous attitude control function that keeps the chip parallel in relation to the SPR instrument by employing the repulsive force of permanent magnets between the float and a float guide located in the SPR instrument. This function is realized by balancing the upward elastic force of the gel and the downward force of the float, which experiences a leveling force from the float guide. This system makes it possible to start an SPR measurement immediately after chip installation and to remove the chip immediately after the measurement with a simple and easy method that does not require any fine adjustment. Our sensor chip, which we installed using this mounting system, successfully performed an immunoassay measurement on a model antigen (spiked human-IgG) in a model real sample (non-homogenized milk) that included many kinds of interfering foreign substances without any sample pre-treatment. The ease of the chip installation/removal operation and simple measurement procedure are suitable for frequent on-site agricultural, environmental and medical testing. PMID:23202030

33 CFR 149.625 - What are the design standards?

Code of Federal Regulations, 2010 CFR

2010-07-01

... elsewhere in this subpart (for example, single point moorings, hoses, and aids to navigation buoys), must be... components. (c) Heliports on floating deepwater ports must be designed in compliance with the regulations at...

33 CFR 329.6 - Interstate or foreign commerce.

Code of Federal Regulations, 2010 CFR

2010-07-01

... United States. Note, however, that the mere presence of floating logs will not of itself make the river... the future, or at a past point in time. (b) Nature of commerce: interstate and intrastate. Interstate...

30 CFR 250.907 - Where must I locate foundation boreholes?

Code of Federal Regulations, 2011 CFR

2011-07-01

... foundation pile to a soil boring must not exceed 500 feet. (b) For deepwater floating platforms which utilize... necessary, other points throughout the anchor pattern to establish the soil profile suitable for foundation...

Soft-core processor study for node-based architectures.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Van Houten, Jonathan Roger; Jarosz, Jason P.; Welch, Benjamin James

2008-09-01

Node-based architecture (NBA) designs for future satellite projects hold the promise of decreasing system development time and costs, size, weight, and power and positioning the laboratory to address other emerging mission opportunities quickly. Reconfigurable Field Programmable Gate Array (FPGA) based modules will comprise the core of several of the NBA nodes. Microprocessing capabilities will be necessary with varying degrees of mission-specific performance requirements on these nodes. To enable the flexibility of these reconfigurable nodes, it is advantageous to incorporate the microprocessor into the FPGA itself, either as a hardcore processor built into the FPGA or as a soft-core processor builtmore » out of FPGA elements. This document describes the evaluation of three reconfigurable FPGA based processors for use in future NBA systems--two soft cores (MicroBlaze and non-fault-tolerant LEON) and one hard core (PowerPC 405). Two standard performance benchmark applications were developed for each processor. The first, Dhrystone, is a fixed-point operation metric. The second, Whetstone, is a floating-point operation metric. Several trials were run at varying code locations, loop counts, processor speeds, and cache configurations. FPGA resource utilization was recorded for each configuration. Cache configurations impacted the results greatly; for optimal processor efficiency it is necessary to enable caches on the processors. Processor caches carry a penalty; cache error mitigation is necessary when operating in a radiation environment.« less

30 CFR 250.431 - What are the diverter design and installation requirements?

Code of Federal Regulations, 2014 CFR

2014-07-01

..., DEPARTMENT OF THE INTERIOR OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Oil and Gas Drilling Operations Diverter System Requirements § 250.431 What are the diverter design and... configurations and at least 12 inches for floating drilling operations; (b) Use dual diverter lines arranged to...

30 CFR 250.431 - What are the diverter design and installation requirements?

Code of Federal Regulations, 2013 CFR

2013-07-01

..., DEPARTMENT OF THE INTERIOR OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Oil and Gas Drilling Operations Diverter System Requirements § 250.431 What are the diverter design and... configurations and at least 12 inches for floating drilling operations; (b) Use dual diverter lines arranged to...

30 CFR 250.433 - What are the diverter actuation and testing requirements?

Code of Federal Regulations, 2010 CFR

2010-07-01

... OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Oil and Gas Drilling Operations...-control systems and control stations. You must also flow-test the vent lines. (a) For drilling operations... must conduct subsequent pressure tests within 7 days after the previous test. (b) For floating drilling...

30 CFR 250.431 - What are the diverter design and installation requirements?

Code of Federal Regulations, 2012 CFR

2012-07-01

..., DEPARTMENT OF THE INTERIOR OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Oil and Gas Drilling Operations Diverter System Requirements § 250.431 What are the diverter design and... configurations and at least 12 inches for floating drilling operations; (b) Use dual diverter lines arranged to...

30 CFR 250.431 - What are the diverter design and installation requirements?

Code of Federal Regulations, 2010 CFR

2010-07-01

... OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Oil and Gas Drilling Operations... floating drilling operations; (b) Use dual diverter lines arranged to provide for downwind diversion capability; (c) Use at least two diverter control stations. One station must be on the drilling floor. The...

Self-Aware Computing

DTIC Science & Technology

2009-06-01

to floating point , to multi-level logic. 2 Overview Self-aware computation can be distinguished from existing computational models which are...systems have advanced to the point that the time is ripe to realize such a system. To illustrate, let us examine each of the key aspects of self...servers for each service, there are no single points of failure in the system. If an OS or user core has a failure, one of several introspection cores

Single crystal growth of 67%BiFeO 3 -33%BaTiO 3 solution by the floating zone method

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rong, Y.; Zheng, H.; Krogstad, M. J.

The growth conditions and the resultant grain morphologies and phase purities from floating-zone growth of 67%BiFeO3-33%BaTiO3 (BF-33BT) single crystals are reported. We find two formidable challenges for the growth. First, a low-melting point constituent leads to a pre-melt zone in the feed-rod that adversely affects growth stability. Second, constitutional super-cooling (CSC), which was found to lead to dendritic and columnar features in the grain morphology, necessitates slow traveling rates during growth. Both challenges were addressed by modifications to the floating-zone furnace that steepened the temperature gradient at the melt-solid interfaces. Slow growth was also required to counter the effects ofmore » CSC. Single crystals with typical dimensions of hundreds of microns have been obtained which possess high quality and are suitable for detailed structural studies.« less

Rear surface effects in high efficiency silicon solar cells

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wenham, S.R.; Robinson, S.J.; Dai, X.

1994-12-31

Rear surface effects in PERL solar cells can lead not only to degradation in the short circuit current and open circuit voltage, but also fill factor. Three mechanisms capable of changing the effective rear surface recombination velocity with injection level are identified, two associated with oxidized p-type surfaces, and the third with two dimensional effects associated with a rear floating junction. Each of these will degrade the fill factor if the range of junction biases corresponding to the rear surface transition, coincides with the maximum power point. Despite the identified non idealities, PERL cells with rear floating junctions (PERF cells)more » have achieved record open circuit voltages for silicon solar cells, while simultaneously achieving fill factor improvements relative to standard PERL solar cells. Without optimization, a record efficiency of 22% has been demonstrated for a cell with a rear floating junction. The results of both theoretical and experimental studies are provided.« less

Single crystal growth of 67%BiFeO3-33%BaTiO3 solution by the floating zone method

NASA Astrophysics Data System (ADS)

Rong, Y.; Zheng, H.; Krogstad, M. J.; Mitchell, J. F.; Phelan, D.

2018-01-01

The growth conditions and the resultant grain morphologies and phase purities from floating-zone growth of 67%BiFeO3-33%BaTiO3 (BF-33BT) single crystals are reported. We find two formidable challenges for the growth. First, a low-melting point constituent leads to a pre-melt zone in the feed-rod that adversely affects growth stability. Second, constitutional super-cooling (CSC), which was found to lead to dendritic and columnar features in the grain morphology, necessitates slow traveling rates during growth. Both challenges were addressed by modifications to the floating-zone furnace that steepened the temperature gradient at the melt-solid interfaces. Slow growth was also required to counter the effects of CSC. Single crystals with typical dimensions of hundreds of microns have been obtained which possess high quality and are suitable for detailed structural studies.

Increased water temperature renders single-housed C57BL/6J mice susceptible to antidepressant treatment in the forced swim test.

PubMed

Bächli, Heidi; Steiner, Michel A; Habersetzer, Ursula; Wotjak, Carsten T

2008-02-11

To investigate genotype x environment interactions in the forced swim test, we tested the influence of water temperature (20 degrees C, 25 degrees C, 30 degrees C) on floating behaviour in single-housed male C57BL/6J and BALB/c mice. We observed a contrasting relationship between floating and water temperature between the two strains, with C57BL/6J floating more and BALB/c floating less with increasing water temperature, independent of the lightening conditions and the time point of testing during the animals' circadian rhythm. Both strains showed an inverse relationship between plasma corticosterone concentration and water temperature, indicating that the differences in stress coping are unrelated to different perception of the aversive encounter. Treatment with desipramine (20mg/kg, i.p.) caused a reduction in immobility time in C57BL/6J mice if the animals were tested at 30 degrees C water temperature, with no effect at 25 degrees C and no effects on forced swim stress-induced corticosterone secretion. The same treatment failed to affect floating behaviour in BALB/c at any temperature, but caused a decrease in plasma corticosterone levels. Taken together we demonstrate that an increase in water temperature in the forced swim test exerts opposite effects on floating behaviour in C57BL/6J and BALB/c and renders single-housed C57BL/6J mice, but not BALB/c mice, susceptible to antidepressant-like behavioral effects of desipramine.

2 CFR 1532.1600 - What definitions apply specifically to actions under this subpart?

Code of Federal Regulations, 2010 CFR

2010-01-01

..., floating craft, location or site of operations that gives rise to a CAA or CWA conviction, and is a... transactions may be performed. If a site of operations giving rise to a CAA or CWA conviction contains or...

U.S.S. Bennington during recovery operations for Apollo 4

NASA Image and Video Library

1967-11-09

U.S.S. Bennington comes alongside the floating Apollo spacecraft 017 Command Module during recovery operations in the mid-Pacific Ocean. The Command Module splashed down at 3:37 p.m., November 9, 1967, 934 nautical miles northwest of Honolulu, Hawaii.

STS-26 MS Hilmers floats in life raft during JSC WETF exercises

NASA Technical Reports Server (NTRS)

1988-01-01

STS-26 Discovery, Orbiter Vehicle (OV) 103, Mission Specialist (MS) David C. Hilmers, wearing the newly designed launch and entry suit (LES), floats in single-occupant life raft in JSC Weightless Environment Training Facility (WETF) Bldg 29 pool. Hilmers pulls his legs into the inflating raft while he is assisted by two SCUBA-equipped divers. The simulation of the escape and rescue operations utilized the crew escape system (CES) pole method of egress from the Space Shuttle.

STS-26 Commander Hauck floats in life raft during JSC WETF exercises

NASA Technical Reports Server (NTRS)

1988-01-01

STS-26 Discovery, Orbiter Vehicle (OV) 103, Commander Frederick H. Hauck, wearing the newly designed launch and entry suit (LES), floats in single-occupant life raft in JSC Weightless Environment Training Facility (WETF) Bldg 29 pool. Removing water from his raft, Hauck awaits the assistance of SCUBA-equipped divers (one of whom is partially visible at bottom right). The simulation of the escape and rescue operations utilized the crew escape system (CES) pole method of egress from the Space Shuttle.

Redox Electrocatalysis of Floating Nanoparticles: Determining Electrocatalytic Properties without the Influence of Solid Supports.

PubMed

Peljo, Pekka; Scanlon, Micheál D; Olaya, Astrid J; Rivier, Lucie; Smirnov, Evgeny; Girault, Hubert H

2017-08-03

Redox electrocatalysis (catalysis of electron-transfer reactions by floating conductive particles) is discussed from the point-of-view of Fermi level equilibration, and an overall theoretical framework is given. Examples of redox electrocatalysis in solution, in bipolar configuration, and at liquid-liquid interfaces are provided, highlighting that bipolar and liquid-liquid interfacial systems allow the study of the electrocatalytic properties of particles without effects from the support, but only liquid-liquid interfaces allow measurement of the electrocatalytic current directly. Additionally, photoinduced redox electrocatalysis will be of interest, for example, to achieve water splitting.

78 FR 25069 - South Carolina Electric & Gas Company; Notice of Application Accepted for Filing and Soliciting...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-04-29

... Murray Docks, Inc./Windward Point Yacht Club to use project waters to expand an existing boat dock facility through the addition of an 8-slip floating dock to accommodate a maximum of 12 additional boats. The proposed new structures would be for the private use of members of the Windward Point Yacht Club...

40 CFR 435.12 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2010 CFR

2010-07-01

... PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS OIL AND GAS EXTRACTION POINT SOURCE CATEGORY... provided in 40 CFR 125.30-32, any existing point source subject to this subpart must achieve the following... maintained as close to this concentration as possible. 3 There shall be no floating solids as a result of the...

Accelerating scientific computations with mixed precision algorithms

NASA Astrophysics Data System (ADS)

Baboulin, Marc; Buttari, Alfredo; Dongarra, Jack; Kurzak, Jakub; Langou, Julie; Langou, Julien; Luszczek, Piotr; Tomov, Stanimire

2009-12-01

On modern architectures, the performance of 32-bit operations is often at least twice as fast as the performance of 64-bit operations. By using a combination of 32-bit and 64-bit floating point arithmetic, the performance of many dense and sparse linear algebra algorithms can be significantly enhanced while maintaining the 64-bit accuracy of the resulting solution. The approach presented here can apply not only to conventional processors but also to other technologies such as Field Programmable Gate Arrays (FPGA), Graphical Processing Units (GPU), and the STI Cell BE processor. Results on modern processor architectures and the STI Cell BE are presented. Program summaryProgram title: ITER-REF Catalogue identifier: AECO_v1_0 Program summary URL:http://cpc.cs.qub.ac.uk/summaries/AECO_v1_0.html Program obtainable from: CPC Program Library, Queen's University, Belfast, N. Ireland Licensing provisions: Standard CPC licence, http://cpc.cs.qub.ac.uk/licence/licence.html No. of lines in distributed program, including test data, etc.: 7211 No. of bytes in distributed program, including test data, etc.: 41 862 Distribution format: tar.gz Programming language: FORTRAN 77 Computer: desktop, server Operating system: Unix/Linux RAM: 512 Mbytes Classification: 4.8 External routines: BLAS (optional) Nature of problem: On modern architectures, the performance of 32-bit operations is often at least twice as fast as the performance of 64-bit operations. By using a combination of 32-bit and 64-bit floating point arithmetic, the performance of many dense and sparse linear algebra algorithms can be significantly enhanced while maintaining the 64-bit accuracy of the resulting solution. Solution method: Mixed precision algorithms stem from the observation that, in many cases, a single precision solution of a problem can be refined to the point where double precision accuracy is achieved. A common approach to the solution of linear systems, either dense or sparse, is to perform the LU factorization of the coefficient matrix using Gaussian elimination. First, the coefficient matrix A is factored into the product of a lower triangular matrix L and an upper triangular matrix U. Partial row pivoting is in general used to improve numerical stability resulting in a factorization PA=LU, where P is a permutation matrix. The solution for the system is achieved by first solving Ly=Pb (forward substitution) and then solving Ux=y (backward substitution). Due to round-off errors, the computed solution, x, carries a numerical error magnified by the condition number of the coefficient matrix A. In order to improve the computed solution, an iterative process can be applied, which produces a correction to the computed solution at each iteration, which then yields the method that is commonly known as the iterative refinement algorithm. Provided that the system is not too ill-conditioned, the algorithm produces a solution correct to the working precision. Running time: seconds/minutes

Hardware description ADSP-21020 40-bit floating point DSP as designed in a remotely controlled digital CW Doppler radar

NASA Astrophysics Data System (ADS)

Morrison, R. E.; Robinson, S. H.

A continuous wave Doppler radar system has been designed which is portable, easily deployed, and remotely controlled. The heart of this system is a DSP/control board using Analog Devices ADSP-21020 40-bit floating point digital signal processor (DSP) microprocessor. Two 18-bit audio A/D converters provide digital input to the DSP/controller board for near real time target detection. Program memory for the DSP is dual ported with an Intel 87C51 microcontroller allowing DSP code to be up-loaded or down-loaded from a central controlling computer. The 87C51 provides overall system control for the remote radar and includes a time-of-day/day-of-year real time clock, system identification (ID) switches, and input/output (I/O) expansion by an Intel 82C55 I/O expander.

Optimized Latching Control of Floating Point Absorber Wave Energy Converter

NASA Astrophysics Data System (ADS)

Gadodia, Chaitanya; Shandilya, Shubham; Bansal, Hari Om

2018-03-01

There is an increasing demand for energy in today’s world. Currently main energy resources are fossil fuels, which will eventually drain out, also the emissions produced from them contribute to global warming. For a sustainable future, these fossil fuels should be replaced with renewable and green energy sources. Sea waves are a gigantic and undiscovered vitality asset. The potential for extricating energy from waves is extensive. To trap this energy, wave energy converters (WEC) are needed. There is a need for increasing the energy output and decreasing the cost requirement of these existing WECs. This paper presents a method which uses prediction as a part of the control scheme to increase the energy efficiency of the floating-point absorber WECs. Kalman Filter is used for estimation, coupled with latching control in regular as well as irregular sea waves. Modelling and Simulation results for the same are also included.

Microfluidic quadrupole and floating concentration gradient.

PubMed

Qasaimeh, Mohammad A; Gervais, Thomas; Juncker, David

2011-09-06

The concept of fluidic multipoles, in analogy to electrostatics, has long been known as a particular class of solutions of the Navier-Stokes equation in potential flows; however, experimental observations of fluidic multipoles and of their characteristics have not been reported yet. Here we present a two-dimensional microfluidic quadrupole and a theoretical analysis consistent with the experimental observations. The microfluidic quadrupole was formed by simultaneously injecting and aspirating fluids from two pairs of opposing apertures in a narrow gap formed between a microfluidic probe and a substrate. A stagnation point was formed at the centre of the microfluidic quadrupole, and its position could be rapidly adjusted hydrodynamically. Following the injection of a solute through one of the poles, a stationary, tunable, and movable-that is, 'floating'-concentration gradient was formed at the stagnation point. Our results lay the foundation for future combined experimental and theoretical exploration of microfluidic planar multipoles including convective-diffusive phenomena.

Atmospheric Modeling And Sensor Simulation (AMASS) study

NASA Technical Reports Server (NTRS)

Parker, K. G.

1984-01-01

The capabilities of the atmospheric modeling and sensor simulation (AMASS) system were studied in order to enhance them. This system is used in processing atmospheric measurements which are utilized in the evaluation of sensor performance, conducting design-concept simulation studies, and also in the modeling of the physical and dynamical nature of atmospheric processes. The study tasks proposed in order to both enhance the AMASS system utilization and to integrate the AMASS system with other existing equipment to facilitate the analysis of data for modeling and image processing are enumerated. The following array processors were evaluated for anticipated effectiveness and/or improvements in throughput by attachment of the device to the P-e: (1) Floating Point Systems AP-120B; (2) Floating Point Systems 5000; (3) CSP, Inc. MAP-400; (4) Analogic AP500; (5) Numerix MARS-432; and (6) Star Technologies, Inc. ST-100.

A fast and low-power microelectromechanical system-based non-volatile memory device

PubMed Central

Lee, Sang Wook; Park, Seung Joo; Campbell, Eleanor E. B.; Park, Yung Woo

2011-01-01

Several new generation memory devices have been developed to overcome the low performance of conventional silicon-based flash memory. In this study, we demonstrate a novel non-volatile memory design based on the electromechanical motion of a cantilever to provide fast charging and discharging of a floating-gate electrode. The operation is demonstrated by using an electromechanical metal cantilever to charge a floating gate that controls the charge transport through a carbon nanotube field-effect transistor. The set and reset currents are unchanged after more than 11 h constant operation. Over 500 repeated programming and erasing cycles were demonstrated under atmospheric conditions at room temperature without degradation. Multinary bit programming can be achieved by varying the voltage on the cantilever. The operation speed of the device is faster than a conventional flash memory and the power consumption is lower than other memory devices. PMID:21364559

Quantity, Revisited: An Object-Oriented Reusable Class

NASA Technical Reports Server (NTRS)

Funston, Monica Gayle; Gerstle, Walter; Panthaki, Malcolm

1998-01-01

"Quantity", a prototype implementation of an object-oriented class, was developed for two reasons: to help engineers and scientists manipulate the many types of quantities encountered during routine analysis, and to create a reusable software component to for large domain-specific applications. From being used as a stand-alone application to being incorporated into an existing computational mechanics toolkit, "Quantity" appears to be a useful and powerful object. "Quantity" has been designed to maintain the full engineering meaning of values with respect to units and coordinate systems. A value is a scalar, vector, tensor, or matrix, each of which is composed of Value Components, each of which may be an integer, floating point number, fuzzy number, etc., and its associated physical unit. Operations such as coordinate transformation and arithmetic operations are handled by member functions of "Quantity". The prototype has successfully tested such characteristics as maintaining a numeric value, an associated unit, and an annotation. In this paper we further explore the design of "Quantity", with particular attention to coordinate systems.

Potential of minicomputer/array-processor system for nonlinear finite-element analysis

NASA Technical Reports Server (NTRS)

Strohkorb, G. A.; Noor, A. K.

1983-01-01

The potential of using a minicomputer/array-processor system for the efficient solution of large-scale, nonlinear, finite-element problems is studied. A Prime 750 is used as the host computer, and a software simulator residing on the Prime is employed to assess the performance of the Floating Point Systems AP-120B array processor. Major hardware characteristics of the system such as virtual memory and parallel and pipeline processing are reviewed, and the interplay between various hardware components is examined. Effective use of the minicomputer/array-processor system for nonlinear analysis requires the following: (1) proper selection of the computational procedure and the capability to vectorize the numerical algorithms; (2) reduction of input-output operations; and (3) overlapping host and array-processor operations. A detailed discussion is given of techniques to accomplish each of these tasks. Two benchmark problems with 1715 and 3230 degrees of freedom, respectively, are selected to measure the anticipated gain in speed obtained by using the proposed algorithms on the array processor.

An implicit spatial and high-order temporal finite difference scheme for 2D acoustic modelling

NASA Astrophysics Data System (ADS)

Wang, Enjiang; Liu, Yang

2018-01-01

The finite difference (FD) method exhibits great superiority over other numerical methods due to its easy implementation and small computational requirement. We propose an effective FD method, characterised by implicit spatial and high-order temporal schemes, to reduce both the temporal and spatial dispersions simultaneously. For the temporal derivative, apart from the conventional second-order FD approximation, a special rhombus FD scheme is included to reach high-order accuracy in time. Compared with the Lax-Wendroff FD scheme, this scheme can achieve nearly the same temporal accuracy but requires less floating-point operation times and thus less computational cost when the same operator length is adopted. For the spatial derivatives, we adopt the implicit FD scheme to improve the spatial accuracy. Apart from the existing Taylor series expansion-based FD coefficients, we derive the least square optimisation based implicit spatial FD coefficients. Dispersion analysis and modelling examples demonstrate that, our proposed method can effectively decrease both the temporal and spatial dispersions, thus can provide more accurate wavefields.

2HOT: An Improved Parallel Hashed Oct-Tree N-Body Algorithm for Cosmological Simulation

DOE PAGES

Warren, Michael S.

2014-01-01

We report on improvements made over the past two decades to our adaptive treecode N-body method (HOT). A mathematical and computational approach to the cosmological N-body problem is described, with performance and scalability measured up to 256k (2 18 ) processors. We present error analysis and scientific application results from a series of more than ten 69 billion (4096 3 ) particle cosmological simulations, accounting for 4×10 20 floating point operations. These results include the first simulations using the new constraints on the standard model of cosmology from the Planck satellite. Our simulations set a new standard for accuracy andmore » scientific throughput, while meeting or exceeding the computational efficiency of the latest generation of hybrid TreePM N-body methods.« less

High temperature aircraft research furnace facilities

NASA Technical Reports Server (NTRS)

Smith, James E., Jr.; Cashon, John L.

1992-01-01

Focus is on the design, fabrication, and development of the High Temperature Aircraft Research Furnace Facilities (HTARFF). The HTARFF was developed to process electrically conductive materials with high melting points in a low gravity environment. The basic principle of operation is to accurately translate a high temperature arc-plasma gas front as it orbits around a cylindrical sample, thereby making it possible to precisely traverse the entire surface of a sample. The furnace utilizes the gas-tungsten-arc-welding (GTAW) process, also commonly referred to as Tungsten-Inert-Gas (TIG). The HTARFF was developed to further research efforts in the areas of directional solidification, float-zone processing, welding in a low-gravity environment, and segregation effects in metals. The furnace is intended for use aboard the NASA-JSC Reduced Gravity Program KC-135A Aircraft.

Japanese project aims at supercomputer that executes 10 gflops

DOE Office of Scientific and Technical Information (OSTI.GOV)

Burskey, D.

1984-05-03

Dubbed supercom by its multicompany design team, the decade-long project's goal is an engineering supercomputer that can execute 10 billion floating-point operations/s-about 20 times faster than today's supercomputers. The project, guided by Japan's Ministry of International Trade and Industry (MITI) and the Agency of Industrial Science and Technology encompasses three parallel research programs, all aimed at some angle of the superconductor. One program should lead to superfast logic and memory circuits, another to a system architecture that will afford the best performance, and the last to the software that will ultimately control the computer. The work on logic and memorymore » chips is based on: GAAS circuit; Josephson junction devices; and high electron mobility transistor structures. The architecture will involve parallel processing.« less

CADNA: a library for estimating round-off error propagation

NASA Astrophysics Data System (ADS)

Jézéquel, Fabienne; Chesneaux, Jean-Marie

2008-06-01

The CADNA library enables one to estimate round-off error propagation using a probabilistic approach. With CADNA the numerical quality of any simulation program can be controlled. Furthermore by detecting all the instabilities which may occur at run time, a numerical debugging of the user code can be performed. CADNA provides new numerical types on which round-off errors can be estimated. Slight modifications are required to control a code with CADNA, mainly changes in variable declarations, input and output. This paper describes the features of the CADNA library and shows how to interpret the information it provides concerning round-off error propagation in a code. Program summaryProgram title:CADNA Catalogue identifier:AEAT_v1_0 Program summary URL:http://cpc.cs.qub.ac.uk/summaries/AEAT_v1_0.html Program obtainable from:CPC Program Library, Queen's University, Belfast, N. Ireland Licensing provisions:Standard CPC licence, http://cpc.cs.qub.ac.uk/licence/licence.html No. of lines in distributed program, including test data, etc.:53 420 No. of bytes in distributed program, including test data, etc.:566 495 Distribution format:tar.gz Programming language:Fortran Computer:PC running LINUX with an i686 or an ia64 processor, UNIX workstations including SUN, IBM Operating system:LINUX, UNIX Classification:4.14, 6.5, 20 Nature of problem:A simulation program which uses floating-point arithmetic generates round-off errors, due to the rounding performed at each assignment and at each arithmetic operation. Round-off error propagation may invalidate the result of a program. The CADNA library enables one to estimate round-off error propagation in any simulation program and to detect all numerical instabilities that may occur at run time. Solution method:The CADNA library [1] implements Discrete Stochastic Arithmetic [2-4] which is based on a probabilistic model of round-off errors. The program is run several times with a random rounding mode generating different results each time. From this set of results, CADNA estimates the number of exact significant digits in the result that would have been computed with standard floating-point arithmetic. Restrictions:CADNA requires a Fortran 90 (or newer) compiler. In the program to be linked with the CADNA library, round-off errors on complex variables cannot be estimated. Furthermore array functions such as product or sum must not be used. Only the arithmetic operators and the abs, min, max and sqrt functions can be used for arrays. Running time:The version of a code which uses CADNA runs at least three times slower than its floating-point version. This cost depends on the computer architecture and can be higher if the detection of numerical instabilities is enabled. In this case, the cost may be related to the number of instabilities detected. References:The CADNA library, URL address: http://www.lip6.fr/cadna. J.-M. Chesneaux, L'arithmétique Stochastique et le Logiciel CADNA, Habilitation á diriger des recherches, Université Pierre et Marie Curie, Paris, 1995. J. Vignes, A stochastic arithmetic for reliable scientific computation, Math. Comput. Simulation 35 (1993) 233-261. J. Vignes, Discrete stochastic arithmetic for validating results of numerical software, Numer. Algorithms 37 (2004) 377-390.

Applications Performance Under MPL and MPI on NAS IBM SP2

NASA Technical Reports Server (NTRS)

Saini, Subhash; Simon, Horst D.; Lasinski, T. A. (Technical Monitor)

1994-01-01

On July 5, 1994, an IBM Scalable POWER parallel System (IBM SP2) with 64 nodes, was installed at the Numerical Aerodynamic Simulation (NAS) Facility Each node of NAS IBM SP2 is a "wide node" consisting of a RISC 6000/590 workstation module with a clock of 66.5 MHz which can perform four floating point operations per clock with a peak performance of 266 Mflop/s. By the end of 1994, 64 nodes of IBM SP2 will be upgraded to 160 nodes with a peak performance of 42.5 Gflop/s. An overview of the IBM SP2 hardware is presented. The basic understanding of architectural details of RS 6000/590 will help application scientists the porting, optimizing, and tuning of codes from other machines such as the CRAY C90 and the Paragon to the NAS SP2. Optimization techniques such as quad-word loading, effective utilization of two floating point units, and data cache optimization of RS 6000/590 is illustrated, with examples giving performance gains at each optimization step. The conversion of codes using Intel's message passing library NX to codes using native Message Passing Library (MPL) and the Message Passing Interface (NMI) library available on the IBM SP2 is illustrated. In particular, we will present the performance of Fast Fourier Transform (FFT) kernel from NAS Parallel Benchmarks (NPB) under MPL and MPI. We have also optimized some of Fortran BLAS 2 and BLAS 3 routines, e.g., the optimized Fortran DAXPY runs at 175 Mflop/s and optimized Fortran DGEMM runs at 230 Mflop/s per node. The performance of the NPB (Class B) on the IBM SP2 is compared with the CRAY C90, Intel Paragon, TMC CM-5E, and the CRAY T3D.

Solidification of floating organic droplet in dispersive liquid-liquid microextraction as a green analytical tool.

PubMed

Mansour, Fotouh R; Danielson, Neil D

2017-08-01

Dispersive liquid-liquid microextraction (DLLME) is a special type of microextraction in which a mixture of two solvents (an extracting solvent and a disperser) is injected into the sample. The extraction solvent is then dispersed as fine droplets in the cloudy sample through manual or mechanical agitation. Hence, the sample is centrifuged to break the formed emulsion and the extracting solvent is manually separated. The organic solvents commonly used in DLLME are halogenated hydrocarbons that are highly toxic. These solvents are heavier than water, so they sink to the bottom of the centrifugation tube which makes the separation step difficult. By using solvents of low density, the organic extractant floats on the sample surface. If the selected solvent such as undecanol has a freezing point in the range 10-25°C, the floating droplet can be solidified using a simple ice-bath, and then transferred out of the sample matrix; this step is known as solidification of floating organic droplet (SFOD). Coupling DLLME to SFOD combines the advantages of both approaches together. The DLLME-SFOD process is controlled by the same variables of conventional liquid-liquid extraction. The organic solvents used as extractants in DLLME-SFOD must be immiscible with water, of lower density, low volatility, high partition coefficient and low melting and freezing points. The extraction efficiency of DLLME-SFOD is affected by types and volumes of organic extractant and disperser, salt addition, pH, temperature, stirring rate and extraction time. This review discusses the principle, optimization variables, advantages and disadvantages and some selected applications of DLLME-SFOD in water, food and biomedical analysis. Copyright © 2017 Elsevier B.V. All rights reserved.

30 CFR 250.432 - How do I obtain a departure to diverter design and installation requirements?

Code of Federal Regulations, 2010 CFR

2010-07-01

..., DEPARTMENT OF THE INTERIOR OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Oil and Gas Drilling Operations Diverter System Requirements § 250.432 How do I obtain a departure to diverter... diverter line for floating drilling operations on a dynamically positioned drillship Maintain an...

30 CFR 250.432 - How do I obtain a departure to diverter design and installation requirements?

Code of Federal Regulations, 2011 CFR

2011-07-01

... MANAGEMENT, REGULATION, AND ENFORCEMENT, DEPARTMENT OF THE INTERIOR OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Oil and Gas Drilling Operations Diverter System Requirements § 250... diameter of at least 8 inches. (d) Use a single diverter line for floating drilling operations on a...

30 CFR 250.432 - How do I obtain a departure to diverter design and installation requirements?

Code of Federal Regulations, 2013 CFR

2013-07-01

... ENVIRONMENTAL ENFORCEMENT, DEPARTMENT OF THE INTERIOR OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Oil and Gas Drilling Operations Diverter System Requirements § 250.432 How do I obtain a... least 8 inches. (d) Use a single diverter line for floating drilling operations on a dynamically...

30 CFR 250.432 - How do I obtain a departure to diverter design and installation requirements?

Code of Federal Regulations, 2014 CFR

2014-07-01

... ENVIRONMENTAL ENFORCEMENT, DEPARTMENT OF THE INTERIOR OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Oil and Gas Drilling Operations Diverter System Requirements § 250.432 How do I obtain a... least 8 inches. (d) Use a single diverter line for floating drilling operations on a dynamically...

30 CFR 250.432 - How do I obtain a departure to diverter design and installation requirements?

Code of Federal Regulations, 2012 CFR

2012-07-01

... ENVIRONMENTAL ENFORCEMENT, DEPARTMENT OF THE INTERIOR OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Oil and Gas Drilling Operations Diverter System Requirements § 250.432 How do I obtain a... least 8 inches. (d) Use a single diverter line for floating drilling operations on a dynamically...

46 CFR 180.207 - Survival craft-vessels operating on lakes, bays, and sounds routes.

Code of Federal Regulations, 2010 CFR

2010-10-01

... sounds routes. 180.207 Section 180.207 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED... Survival Craft § 180.207 Survival craft—vessels operating on lakes, bays, and sounds routes. (a) Except as... operate on a lakes, bays, and sounds route in cold water must either: (1) Be provided with life floats of...

46 CFR 180.207 - Survival craft-vessels operating on lakes, bays, and sounds routes.

Code of Federal Regulations, 2012 CFR

2012-10-01

... sounds routes. 180.207 Section 180.207 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED... Survival Craft § 180.207 Survival craft—vessels operating on lakes, bays, and sounds routes. (a) Except as... operate on a lakes, bays, and sounds route in cold water must either: (1) Be provided with life floats of...

46 CFR 180.207 - Survival craft-vessels operating on lakes, bays, and sounds routes.

Code of Federal Regulations, 2013 CFR

2013-10-01

... sounds routes. 180.207 Section 180.207 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED... Survival Craft § 180.207 Survival craft—vessels operating on lakes, bays, and sounds routes. (a) Except as... operate on a lakes, bays, and sounds route in cold water must either: (1) Be provided with life floats of...

46 CFR 180.207 - Survival craft-vessels operating on lakes, bays, and sounds routes.

Code of Federal Regulations, 2014 CFR

2014-10-01

... sounds routes. 180.207 Section 180.207 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED... Survival Craft § 180.207 Survival craft—vessels operating on lakes, bays, and sounds routes. (a) Except as... operate on a lakes, bays, and sounds route in cold water must either: (1) Be provided with life floats of...

46 CFR 180.207 - Survival craft-vessels operating on lakes, bays, and sounds routes.

Code of Federal Regulations, 2011 CFR

2011-10-01

... sounds routes. 180.207 Section 180.207 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED... Survival Craft § 180.207 Survival craft—vessels operating on lakes, bays, and sounds routes. (a) Except as... operate on a lakes, bays, and sounds route in cold water must either: (1) Be provided with life floats of...

Method and apparatus for high speed data acquisition and processing

DOEpatents

Ferron, J.R.

1997-02-11

A method and apparatus are disclosed for high speed digital data acquisition. The apparatus includes one or more multiplexers for receiving multiple channels of digital data at a low data rate and asserting a multiplexed data stream at a high data rate, and one or more FIFO memories for receiving data from the multiplexers and asserting the data to a real time processor. Preferably, the invention includes two multiplexers, two FIFO memories, and a 64-bit bus connecting the FIFO memories with the processor. Each multiplexer receives four channels of 14-bit digital data at a rate of up to 5 MHz per channel, and outputs a data stream to one of the FIFO memories at a rate of 20 MHz. The FIFO memories assert output data in parallel to the 64-bit bus, thus transferring 14-bit data values to the processor at a combined rate of 40 MHz. The real time processor is preferably a floating-point processor which processes 32-bit floating-point words. A set of mask bits is prestored in each 32-bit storage location of the processor memory into which a 14-bit data value is to be written. After data transfer from the FIFO memories, mask bits are concatenated with each stored 14-bit data value to define a valid 32-bit floating-point word. Preferably, a user can select any of several modes for starting and stopping direct memory transfers of data from the FIFO memories to memory within the real time processor, by setting the content of a control and status register. 15 figs.

Method and apparatus for high speed data acquisition and processing

DOEpatents

Ferron, John R.

1997-01-01

A method and apparatus for high speed digital data acquisition. The apparatus includes one or more multiplexers for receiving multiple channels of digital data at a low data rate and asserting a multiplexed data stream at a high data rate, and one or more FIFO memories for receiving data from the multiplexers and asserting the data to a real time processor. Preferably, the invention includes two multiplexers, two FIFO memories, and a 64-bit bus connecting the FIFO memories with the processor. Each multiplexer receives four channels of 14-bit digital data at a rate of up to 5 MHz per channel, and outputs a data stream to one of the FIFO memories at a rate of 20 MHz. The FIFO memories assert output data in parallel to the 64-bit bus, thus transferring 14-bit data values to the processor at a combined rate of 40 MHz. The real time processor is preferably a floating-point processor which processes 32-bit floating-point words. A set of mask bits is prestored in each 32-bit storage location of the processor memory into which a 14-bit data value is to be written. After data transfer from the FIFO memories, mask bits are concatenated with each stored 14-bit data value to define a valid 32-bit floating-point word. Preferably, a user can select any of several modes for starting and stopping direct memory transfers of data from the FIFO memories to memory within the real time processor, by setting the content of a control and status register.

Open-air sprays for capturing and controlling airborne float coal dust on longwall faces

PubMed Central

Beck, T.W.; Seaman, C.E.; Shahan, M.R.; Mischler, S.E.

2018-01-01

Float dust deposits in coal mine return airways pose a risk in the event of a methane ignition. Controlling airborne dust prior to deposition in the return would make current rock dusting practices more effective and reduce the risk of coal-dust-fueled explosions. The goal of this U.S. National Institute for Occupational Safety and Health study is to determine the potential of open-air water sprays to reduce concentrations of airborne float coal dust, smaller than 75 µm in diameter, in longwall face airstreams. This study evaluated unconfined water sprays in a featureless tunnel ventilated at a typical longwall face velocity of 3.6 m/s (700 fpm). Experiments were conducted for two nozzle orientations and two water pressures for hollow cone, full cone, flat fan, air atomizing and hydraulic atomizing spray nozzles. Gravimetric samples show that airborne float dust removal efficiencies averaged 19.6 percent for all sprays under all conditions. The results indicate that the preferred spray nozzle should be operated at high fluid pressures to produce smaller droplets and move more air. These findings agree with past respirable dust control research, providing guidance on spray selection and spray array design in ongoing efforts to control airborne float dust over the entire longwall ventilated opening. PMID:29348700

The floating knee: epidemiology, prognostic indicators & outcome following surgical management

PubMed Central

Rethnam, Ulfin; Yesupalan, Rajam S; Nair, Rajagopalan

2007-01-01

Background Floating Knee injuries are complex injuries. The type of fractures, soft tissue and associated injuries make this a challenging problem to manage. We present the outcome of these injuries after surgical management. Methods 29 patients with floating knee injuries were managed over a 3 year period. This was a prospective study were both fractures of the floating knee injury were surgically fixed using different modalities. The associated injuries were managed appropriately. Assessment of the end result was done by the Karlstrom criteria after bony union. Results The mechanism of injury was road traffic accident in 27/29 patients. There were 38 associated injuries. 20/29 patients had intramedullary nailing for both fractures. The complications were knee stiffness, foot drop, delayed union of tibia and superficial infection. The bony union time ranged from 15 – 22.5 weeks for femur fractures and 17 – 28 weeks for the tibia. According to the Karlstrom criteria the end results were Excellent – 15, Good – 11, Acceptable – 1 and Poor – 3. Conclusion The associated injuries and the type of fracture (open, intra-articular, comminution) are prognostic indicators in the Floating knee. Appropriate management of the associated injuries, intramedullary nailing of both the fractures and post operative rehabilitation are necessary for good final outcome. PMID:18271992

Open-air sprays for capturing and controlling airborne float coal dust on longwall faces.

PubMed

Beck, T W; Seaman, C E; Shahan, M R; Mischler, S E

2018-01-01

Float dust deposits in coal mine return airways pose a risk in the event of a methane ignition. Controlling airborne dust prior to deposition in the return would make current rock dusting practices more effective and reduce the risk of coal-dust-fueled explosions. The goal of this U.S. National Institute for Occupational Safety and Health study is to determine the potential of open-air water sprays to reduce concentrations of airborne float coal dust, smaller than 75 µm in diameter, in longwall face airstreams. This study evaluated unconfined water sprays in a featureless tunnel ventilated at a typical longwall face velocity of 3.6 m/s (700 fpm). Experiments were conducted for two nozzle orientations and two water pressures for hollow cone, full cone, flat fan, air atomizing and hydraulic atomizing spray nozzles. Gravimetric samples show that airborne float dust removal efficiencies averaged 19.6 percent for all sprays under all conditions. The results indicate that the preferred spray nozzle should be operated at high fluid pressures to produce smaller droplets and move more air. These findings agree with past respirable dust control research, providing guidance on spray selection and spray array design in ongoing efforts to control airborne float dust over the entire longwall ventilated opening.

Aerial LED signage by use of crossed-mirror array

NASA Astrophysics Data System (ADS)

Yamamoto, Hirotsugu; Kujime, Ryousuke; Bando, Hiroki; Suyama, Shiro

2013-03-01

3D representation of digital signage improves its significance and rapid notification of important points. Real 3D display techniques such as volumetric 3D displays are effective for use of 3D for public signs because it provides not only binocular disparity but also motion parallax and other cues, which will give 3D impression even people with abnormal binocular vision. Our goal is to realize aerial 3D LED signs. We have specially designed and fabricated a reflective optical device to form an aerial image of LEDs with a wide field angle. The developed reflective optical device composed of crossed-mirror array (CMA). CMA contains dihedral corner reflectors at each aperture. After double reflection, light rays emitted from an LED will converge into the corresponding image point. The depth between LED lamps is represented in the same depth in the floating 3D image. Floating image of LEDs was formed in wide range of incident angle with a peak reflectance at 35 deg. The image size of focused beam (point spread function) agreed to the apparent aperture size.

40 CFR 426.54 - [Reserved

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 30 2011-07-01 2011-07-01 false [Reserved] 426.54 Section 426.54 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS GLASS MANUFACTURING POINT SOURCE CATEGORY Float Glass Manufacturing Subcategory § 426.54 [Reserved] ...

40 CFR 426.54 - [Reserved

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 29 2010-07-01 2010-07-01 false [Reserved] 426.54 Section 426.54 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS GLASS MANUFACTURING POINT SOURCE CATEGORY Float Glass Manufacturing Subcategory § 426.54 [Reserved] ...

33 CFR 100.101 - Harvard-Yale Regatta, Thames River, New London, CT.

Code of Federal Regulations, 2010 CFR

2010-07-01

... race course, between Scotch Cap and Bartlett Point Light. (ii) Within the race course boundaries or in... not cause waves which result in damage to submarines or other vessels in the floating drydocks. (11...

75 FR 5073 - Alabama Power Company; Notice of Application for Amendment of License and Soliciting Comments...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-02-01

... facilities associated with the Willow Glynn at Willow Point residential subdivision. These facilities include 2 floating docks, with 16 double-slips each, a wooden pedestrian bridge, a wooden boardwalk along 1...

40 CFR 125.133 - What special definitions apply to this subpart?

Code of Federal Regulations, 2010 CFR

2010-07-01

... Subcategories of the Oil and Gas Extraction Point Source Category Effluent Guidelines in 40 CFR 435.10 or 40 CFR..., floating, mobile, facility engaged in the processing of fresh, frozen, canned, smoked, salted or pickled...

33 CFR 110.29 - Boston Inner Harbor, Mass.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Park Yacht Club, Winthrop. Southerly of a line bearing 276° from a point on the west side of Pleasant.... [NAD83]. (2) The area is principally for use by yachts and other recreational craft. Temporary floats or...

33 CFR 110.29 - Boston Inner Harbor, Mass.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Park Yacht Club, Winthrop. Southerly of a line bearing 276° from a point on the west side of Pleasant.... [NAD83]. (2) The area is principally for use by yachts and other recreational craft. Temporary floats or...

Investigation of Response Amplitude Operators for Floating Offshore Wind Turbines: Preprint

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ramachandran, G. K. V.; Robertson, A.; Jonkman, J. M.

This paper examines the consistency between response amplitude operators (RAOs) computed from WAMIT, a linear frequency-domain tool, to RAOs derived from time-domain computations based on white-noise wave excitation using FAST, a nonlinear aero-hydro-servo-elastic tool. The RAO comparison is first made for a rigid floating wind turbine without wind excitation. The investigation is further extended to examine how these RAOs change for a flexible and operational wind turbine. The RAOs are computed for below-rated, rated, and above-rated wind conditions. The method is applied to a floating wind system composed of the OC3-Hywind spar buoy and NREL 5-MW wind turbine. The responsesmore » are compared between FAST and WAMIT to verify the FAST model and to understand the influence of structural flexibility, aerodynamic damping, control actions, and waves on the system responses. The results show that based on the RAO computation procedure implemented, the WAMIT- and FAST-computed RAOs are similar (as expected) for a rigid turbine subjected to waves only. However, WAMIT is unable to model the excitation from a flexible turbine. Further, the presence of aerodynamic damping decreased the platform surge and pitch responses, as computed by both WAMIT and FAST when wind was included. Additionally, the influence of gyroscopic excitation increased the yaw response, which was captured by both WAMIT and FAST.« less

Channel-Like Bottom Features and High Bottom Melt Rates of Petermann Gletscher's Floating Tongue in Northwestern Greenland

NASA Astrophysics Data System (ADS)

Steffen, K.; Huff, R. D.; Cullen, N.; Rignot, E.; Stewart, C.; Jenkins, A.

2003-12-01

Petermann Gletscher is the largest and most influential outlet glacier in central northern Greenland. Located at 81 N, 60 W, it drains an area of 71,580 km2, with a discharge of 12 cubic km of ice per year into the Arctic Ocean. We finished a second field season in spring 2003 collecting in situ data on local climate, ice velocity, strain rates, ice thickness profiles and bottom melt rates of the floating ice tongue. Last years findings have been confirmed that large channels of several hundred meters in depth at the underside of the floating ice tongue are running roughly parallel to the flow direction. We mapped these channels using ground penetrating radar at 25 MHz frequency and multi-phase radar in profiling mode over half of the glacier's width. In addition, NASA airborne laser altimeter data was collected along and cross-glacier for accurate assessment of surface topography. We will present a 3-D model of the floating ice tongue and provide hypothesis of the origin and mechanism that caused these large ice channels at the bottom of the floating ice tongue. Multi-phase radar point measurements revealed interesting results of bottom melt rates, which exceed all previous estimates. It is worth mentioned that the largest bottom melt rates were not found at the grounding line, which is common on ice shelves in the Antarctica. In addition, GPS tidal motion has been measured over one lunar cycle at the flex zone and on the free floating ice tongue and the result will be compared to historic measurements made at the beginning of last century. The surface climate has been recorded by two automatic weather stations over a 12 month period, and the local climate of this remote region will be presented.

76 FR 23964 - Fisheries in the Western Pacific; Pelagic Fisheries; Purse Seine Prohibited Areas Around American...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-04-29

... animals, such as pelagic fishes and sea turtles, tend to congregate to naturally-occurring floating... American Samoa enclosed by straight lines connecting the following coordinates: Point S. latitude W. longitude AS-3-A 11[deg]12[min] 172[deg]18[min] AS-3-B 12[deg]12[min] 169[deg]56[min] and from Point AS-3-A...

75 FR 33692 - Safety Zone; Tacoma Freedom Fair Air Show, Commencement Bay, Tacoma, WA

Federal Register 2010, 2011, 2012, 2013, 2014

2010-06-15

... this rule encompasses all waters within the points 47[deg]-17.63' N., 122[deg]-28.724' W.; 47[deg]-17... Ruston Way and extending approximately 1100 yards into Commencement Bay. Floating markers will be placed... designated safety zone: All waters within the points 47[deg]-17.63' N., 122[deg]-28.724' W.; 47[deg]-17.059...

Circulation patterns in the deep Subtropical Northeast Atlantic with ARGO data

NASA Astrophysics Data System (ADS)

Calheiros, Tomas; Bashmachnikov, Igor

2014-05-01

In this work we study the dominant circulation patterns in the Subtropical Northeast Atlantic using ARGO data [25-45o N, 5-35o W]. The data were obtained from the Coriolis operational data center (ftp://ftp.ifremer.fr) for the years 1999-2013. During this period of time in the study there were available area 376 floats with 15062 float-months of total time. The floats were launched in the depths range between 300 and 2000 m, but most of the floats were concentrated at 1000 m (2000 float-months) and 1500 m (3400 float-months). In the upper 400-m layer there were also about 1000 float-months, but their number and distribution did not allow analysis of the mean currents over the study region. For each float position Lagrangian current velocity was computed as the difference between the position when the buoy started sinking to the reference depth and the consequent position of surfacing of the float, divided by the respective time interval. This allowed reducing the noise related with sea-surface drift of the buoys during the data-transmission periods. Mean Eulerian velocity and its error were computed in each of the 2ox2o square. Whenever in a 2ox2o square more than 150 observations of the Lagrangian velocity were available, the square was split into 4 smaller 1ox1o squares, in each of which the mean Eulerian velocities and their errors were estimated. Eulerian currents at 1000 m, as well as at 1500 m depth formed an overall anticyclonic circulation pattern in the study region. The modal velocity of all buoys at 1000 m level was 4 cm/s with an error of the mean of 1.8 cm/s. The modal velocity of all buoys at 1500m was 3 cm/s with an error of the mean of 1.4 cm/s. The southwestward flows near the Madeira Island and further westwards flow along the zonal band of 25-30o N at 1500 m depth well corresponded to the extension of the deep fraction of the Mediterranean Water salt tong.

Ambipolar nonvolatile memory based on a quantum-dot transistor with a nanoscale floating gate

DOE Office of Scientific and Technical Information (OSTI.GOV)

Che, Yongli; Zhang, Yating, E-mail: yating@tju.edu.cn; Song, Xiaoxian

2016-07-04

Using only solution processing methods, we developed ambipolar quantum-dot (QD) transistor floating-gate memory (FGM) that uses Au nanoparticles as a floating gate. Because of the bipolarity of the active channel of PbSe QDs, the memory could easily trap holes or electrons in the floating gate by programming/erasing (P/E) operations, which could shift the threshold voltage both up and down. As a result, the memory exhibited good programmable memory characteristics: a large memory window (ΔV{sub th} ∼ 15 V) and a long retention time (>10{sup 5 }s). The magnitude of ΔV{sub th} depended on both P/E voltages and the bias voltage (V{sub DS}): ΔV{sub th}more » was a cubic function to V{sub P/E} and linearly depended on V{sub DS}. Therefore, this FGM based on a QD transistor is a promising alternative to its inorganic counterparts owing to its advantages of bipolarity, high mobility, low cost, and large-area production.« less

A quantum molecular similarity analysis of changes in molecular electron density caused by basis set flotation and electric field application

NASA Astrophysics Data System (ADS)

Simon, Sílvia; Duran, Miquel

1997-08-01

Quantum molecular similarity (QMS) techniques are used to assess the response of the electron density of various small molecules to application of a static, uniform electric field. Likewise, QMS is used to analyze the changes in electron density generated by the process of floating a basis set. The results obtained show an interrelation between the floating process, the optimum geometry, and the presence of an external field. Cases involving the Le Chatelier principle are discussed, and an insight on the changes of bond critical point properties, self-similarity values and density differences is performed.

Development of a Semi-submersible Barge for the installation of a TLP floating substructure. TLPWIND® case study

NASA Astrophysics Data System (ADS)

Amate, Juan; Sánchez, Gustavo D.; González, Gonzalo

2016-09-01

One of the biggest challenges to introduce Tension Leg Platform (TLP) technology into the Offshore Wind market are the Transport & Installation (T&I) stages, since most of TLPs are not self-stable as semisubmersible or SPAR platforms, and consequently requires additional means to perform these operations. This paper addresses this problem that has been overcome through the development of a Semi-submersible “Transport & Installation” Barge (SSB) for Iberdrola's TLPWIND® floating support structure. The Semi-submersible Barge has been designed both through the use of numerical models and an extensive basin testing campaign carried out at the University of Strathclyde facilities. This paper also includes an estimation of the duration in time to carry out the installation process of a Floating Offshore Wind Farm, comprising 100x5MW TLPWIND® units in different scenarios.

40 CFR 63.11955 - What are my initial and continuous compliance requirements for other emission sources?

Code of Federal Regulations, 2012 CFR

2012-07-01

... times except during periods of maintenance or repair. The standard operating procedures must be... layer; and/or (iv) Floating mats. (3) Each gasholder must have established operating procedures that... ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS...

40 CFR 63.11955 - What are my initial and continuous compliance requirements for other emission sources?

Code of Federal Regulations, 2014 CFR

2014-07-01

... times except during periods of maintenance or repair. The standard operating procedures must be... layer; and/or (iv) Floating mats. (3) Each gasholder must have established operating procedures that... ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS...

40 CFR 63.11955 - What are my initial and continuous compliance requirements for other emission sources?

Code of Federal Regulations, 2013 CFR

2013-07-01

... times except during periods of maintenance or repair. The standard operating procedures must be... layer; and/or (iv) Floating mats. (3) Each gasholder must have established operating procedures that... ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS...

Using a Floating-Gate MOS Transistor as a Transducer in a MEMS Gas Sensing System

PubMed Central

Barranca, Mario Alfredo Reyes; Mendoza-Acevedo, Salvador; Flores-Nava, Luis M.; Avila-García, Alejandro; Vazquez-Acosta, E. N.; Moreno-Cadenas, José Antonio; Casados-Cruz, Gaspar

2010-01-01

Floating-gate MOS transistors have been widely used in diverse analog and digital applications. One of these is as a charge sensitive device in sensors for pH measurement in solutions or using gates with metals like Pd or Pt for hydrogen sensing. Efforts are being made to monolithically integrate sensors together with controlling and signal processing electronics using standard technologies. This can be achieved with the demonstrated compatibility between available CMOS technology and MEMS technology. In this paper an in-depth analysis is done regarding the reliability of floating-gate MOS transistors when charge produced by a chemical reaction between metallic oxide thin films with either reducing or oxidizing gases is present. These chemical reactions need temperatures around 200 °C or higher to take place, so thermal insulation of the sensing area must be assured for appropriate operation of the electronics at room temperature. The operation principle of the proposal here presented is confirmed by connecting the gate of a conventional MOS transistor in series with a Fe2O3 layer. It is shown that an electrochemical potential is present on the ferrite layer when reacting with propane. PMID:22163478

Separation of plastics: The importance of kinetics knowledge in the evaluation of froth flotation.

PubMed

Censori, Matteo; La Marca, Floriana; Carvalho, M Teresa

2016-08-01

Froth flotation is a promising technique to separate polymers of similar density. The present paper shows the need for performing kinetic tests to evaluate and optimize the process. In the experimental study, batch flotation tests were performed on samples of ABS and PS. The floated product was collected at increasing flotation time. Two variables were selected for modification: the concentration of the depressor (tannic acid) and airflow rate. The former is associated with the chemistry of the process and the latter with the transport of particles. It was shown that, like mineral flotation, plastics flotation can be adequately assumed as a first order rate process. The results of the kinetic tests showed that the kinetic parameters change with the operating conditions. When the depressing action is weak and the airflow rate is low, the kinetic is fast. Otherwise, the kinetic is slow and a variable percentage of the plastics never floats. Concomitantly, the time at which the maximum difference in the recovery of the plastics in the floated product is attained changes with the operating conditions. The prediction of flotation results, process evaluation and comparisons should be done considering the process kinetics. Copyright © 2016 Elsevier Ltd. All rights reserved.

Generalized and efficient algorithm for computing multipole energies and gradients based on Cartesian tensors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lin, Dejun, E-mail: dejun.lin@gmail.com

2015-09-21

Accurate representation of intermolecular forces has been the central task of classical atomic simulations, known as molecular mechanics. Recent advancements in molecular mechanics models have put forward the explicit representation of permanent and/or induced electric multipole (EMP) moments. The formulas developed so far to calculate EMP interactions tend to have complicated expressions, especially in Cartesian coordinates, which can only be applied to a specific kernel potential function. For example, one needs to develop a new formula each time a new kernel function is encountered. The complication of these formalisms arises from an intriguing and yet obscured mathematical relation between themore » kernel functions and the gradient operators. Here, I uncover this relation via rigorous derivation and find that the formula to calculate EMP interactions is basically invariant to the potential kernel functions as long as they are of the form f(r), i.e., any Green’s function that depends on inter-particle distance. I provide an algorithm for efficient evaluation of EMP interaction energies, forces, and torques for any kernel f(r) up to any arbitrary rank of EMP moments in Cartesian coordinates. The working equations of this algorithm are essentially the same for any kernel f(r). Recently, a few recursive algorithms were proposed to calculate EMP interactions. Depending on the kernel functions, the algorithm here is about 4–16 times faster than these algorithms in terms of the required number of floating point operations and is much more memory efficient. I show that it is even faster than a theoretically ideal recursion scheme, i.e., one that requires 1 floating point multiplication and 1 addition per recursion step. This algorithm has a compact vector-based expression that is optimal for computer programming. The Cartesian nature of this algorithm makes it fit easily into modern molecular simulation packages as compared with spherical coordinate-based algorithms. A software library based on this algorithm has been implemented in C++11 and has been released.« less

Highly anomalous accumulation rates of C and N recorded by a relic, free-floating peatland in Central Italy

PubMed Central

Zaccone, Claudio; Lobianco, Daniela; Shotyk, William; Ciavatta, Claudio; Appleby, Peter G.; Brugiapaglia, Elisabetta; Casella, Laura; Miano, Teodoro M.; D’Orazio, Valeria

2017-01-01

Floating islands mysteriously moving around on lakes were described by several Latin authors almost two millennia ago. These fascinating ecosystems, known as free-floating mires, have been extensively investigated from ecological, hydrological and management points of view, but there have been no detailed studies of their rates of accumulation of organic matter (OM), organic carbon (OC) and total nitrogen (TN). We have collected a peat core 4 m long from the free-floating island of Posta Fibreno, a relic mire in Central Italy. This is the thickest accumulation of peat ever found in a free-floating mire, yet it has formed during the past seven centuries and represents the greatest accumulation rates, at both decadal and centennial timescale, of OM (0.63 vs. 0.37 kg/m2/yr), OC (0.28 vs. 0.18 kg/m2/yr) and TN (3.7 vs. 6.1 g/m2/yr) ever reported for coeval peatlands. The anomalously high accretion rates, obtained using 14C age dating, were confirmed using 210Pb and 137Cs: these show that the top 2 m of Sphagnum-peat has accumulated in only ~100 years. As an environmental archive, Posta Fibreno offers a temporal resolution which is 10x greater than any terrestrial peat bog, and promises to provide new insight into environmental changes occurring during the Anthropocene. PMID:28230066

40 CFR 426.51 - Specialized definitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 29 2010-07-01 2010-07-01 false Specialized definitions. 426.51 Section 426.51 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS GLASS MANUFACTURING POINT SOURCE CATEGORY Float Glass Manufacturing Subcategory § 426.51...

40 CFR 426.51 - Specialized definitions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 30 2011-07-01 2011-07-01 false Specialized definitions. 426.51 Section 426.51 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS GLASS MANUFACTURING POINT SOURCE CATEGORY Float Glass Manufacturing Subcategory § 426.51...

Efficient Atomization and Combustion of Emulsified Crude Oil

DTIC Science & Technology

2014-09-18

2.26 Naphthenes , vol % 50.72 Aromatics, vol % 16.82 Freezing Point, °F -49.7 Freezing Point, °C -45.4 Smoke Point, mm (ASTM) 19.2 Acid ...needed by the proposed method for capturing and oil removal , in particular the same vessels and booms used to herd the floating crude oil into a thick...slicks need to be removed more rapidly than they can be transported, in situ burning offers a rapid disposal method that minimizes risk to marine life

Computer Program to Add NOISEMAP Grids of Different Spacings

DTIC Science & Technology

1980-04-01

GRIC POINT. C 1,J ARE THE INDICES !-OR THE #-IN’- GRIL , PUINT CLOSLSTP C uUT TO THE LkFT AND 8tLGW9 T~ic Oi.JIRL&j iEIG GkIO POIt4TO C .(1,RJ ARE THE...ACTUAL FLOATING POINT CUORGINATES THE bIG C i.kID POINT WOULD HAVE WERL IT IN THE i-INL GRIL .. C CUMMION /GRIOS/ NBF, NBFL, OG(IOUIOO), dSo FG(iI.0QI,1

Impact of Solar Array Position on ISS Vehicle Charging

NASA Technical Reports Server (NTRS)

Alred, John; Mikatarian, Ronald; Koontz, Steve

2006-01-01

The International Space Station (ISS), because of its large structure and high voltage solar arrays, has a complex plasma interaction with the ionosphere in low Earth orbit (LEO). This interaction of the ISS US Segment photovoltaic (PV) power system with the LEO ionospheric plasma produces floating potentials on conducting elements of the ISS structure relative to the local plasma environment. To control the ISS floating potentials, two Plasma Contactor Units (PCUs) are installed on the Z1 truss. Each PCU discharges accumulated electrons from the Space Station structure, thus reducing the potential difference between the ISS structure and the surrounding charged plasma environment. Operations of the PCUs were intended to keep the ISS floating potential to 40 Volts (Reference 1). Exposed dielectric surfaces overlying conducting structure on the Space Station will collect an opposite charge from the ionosphere as the ISS charges. In theory, when an Extravehicular Activity (EVA) crewmember is tethered to structure via the crew safety tether or when metallic surfaces of the Extravehicular Mobility Unit (EMU) come in contact with conducting metallic surfaces of the ISS, the EMU conducting components, including the perspiration-soaked crewmember inside, can become charged to the Space Station floating potential. The concern is the potential dielectric breakdown of anodized aluminum surfaces on the EMU producing an arc from the EMU to the ambient plasma, or nearby ISS structure. If the EMU arcs, an electrical current of an unknown magnitude and duration may conduct through the EVA crewmember, producing an unacceptable condition. This electrical current may be sufficient to startle or fatally shock the EVA crewmember (Reference 2). Hence, as currently defined by the EVA community, the ISS floating potential for all nominal and contingency EVA worksites and translation paths must have a magnitude less than 40 volts relative to the local ionosphere at all times during EVA. Arcing from the EMU is classified as a catastrophic hazard, which requires two-failure tolerant controls, i.e., three hazard controls. Each PCU is capable of maintaining the ISS floating potential below the requirement during EVA. The two PCUs provide a single failure tolerant control of ISS floating potential. In the event of the failure of one or two PCUs, a combination of solar array shunting and turning the solar arrays into their own wakes will be used to supply control of the plasma hazard (Reference 3). The purpose of this paper is to present on-orbit information that shows that ISS solar array placement with respect to the ISS velocity vector can control solar array plasma charging, and hence, provide an operational control for the plasma hazard. Also, this paper will present on-orbit information that shows that shunting of the ISS solar arrays can control solar array plasma charging, and hence, provide an additional operational control for the plasma hazard.

Flow-induced oscillations of a floating moored cylinder

NASA Astrophysics Data System (ADS)

Carlson, Daniel; Modarres-Sadeghi, Yahya

2016-11-01

An experimental study of flow-induced oscillations of a floating model spar buoy was conducted. The model spar consisted of a floating uniform cylinder moored in a water tunnel test section, and free to oscillate about its mooring attachment point near the center of mass. For the bare cylinder, counter-clockwise (CCW) figure-eight trajectories approaching A* =1 in amplitude were observed at the lower part of the spar for a reduced velocity range of U* =4-11, while its upper part experienced clockwise (CW) orbits. It was hypothesized that the portion of the spar undergoing CCW figure eights is the portion within which the flow excites the structure. By adding helical strakes to the portion of the cylinder with CCW figure eights, the response amplitude was significantly reduced, while adding strakes to portions with clockwise orbital motion had a minimal influence on the amplitude of response. This work is partially supported by the NSF-sponsored IGERT: Offshore Wind Energy Engineering, Environmental Science, and Policy (Grant Number 1068864).

Measuring mandibular motions

NASA Technical Reports Server (NTRS)

Dimeff, J.; Rositano, S.; Taylor, R. C.

1977-01-01

Mandibular motion along three axes is measured by three motion transducers on floating yoke that rests against mandible. System includes electronics to provide variety of outputs for data display and processing. Head frame is strapped to test subject's skull to provide fixed point of reference for transducers.

40 CFR 426.56 - Pretreatment standards for new sources.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 29 2010-07-01 2010-07-01 false Pretreatment standards for new sources. 426.56 Section 426.56 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS GLASS MANUFACTURING POINT SOURCE CATEGORY Float Glass Manufacturing Subcategory...

40 CFR 426.56 - Pretreatment standards for new sources.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 30 2011-07-01 2011-07-01 false Pretreatment standards for new sources. 426.56 Section 426.56 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS GLASS MANUFACTURING POINT SOURCE CATEGORY Float Glass Manufacturing Subcategory...

46 CFR 46.10-45 - Nonsubmergence subdivision load lines in salt water.

Code of Federal Regulations, 2010 CFR

2010-10-01

... which the vessel is floating but not for the weight of fuel, water, etc., required for consumption between the point of departure and the open sea, and no allowance is to be made for bilge or ballast water...

75 FR 19880 - Safety Zone; BW PIONEER at Walker Ridge 249, Outer Continental Shelf FPSO, Gulf of Mexico

Federal Register 2010, 2011, 2012, 2013, 2014

2010-04-16

... BW PIONEER, a Floating Production, Storage and Offloading (FPSO) system, at Walker Ridge 249 in the... point at 26[deg]41'46.25'' N and 090[deg]30'30.16'' W. This action is based on a thorough and... regulations. The FPSO can swing in a 360 degree arc around the center point. The safety zone will reduce...

Solid dispersions in the development of a nimodipine floating tablet formulation and optimization by artificial neural networks and genetic programming.

PubMed

Barmpalexis, Panagiotis; Kachrimanis, Kyriakos; Georgarakis, Emanouil

2011-01-01

The present study investigates the use of nimodipine-polyethylene glycol solid dispersions for the development of effervescent controlled release floating tablet formulations. The physical state of the dispersed nimodipine in the polymer matrix was characterized by differential scanning calorimetry, powder X-ray diffraction, FT-IR spectroscopy and polarized light microscopy, and the mixture proportions of polyethylene glycol (PEG), polyvinyl-pyrrolidone (PVP), hydroxypropylmethylcellulose (HPMC), effervescent agents (EFF) and nimodipine were optimized in relation to drug release (% release at 60 min, and time at which the 90% of the drug was dissolved) and floating properties (tablet's floating strength and duration), employing a 25-run D-optimal mixture design combined with artificial neural networks (ANNs) and genetic programming (GP). It was found that nimodipine exists as mod I microcrystals in the solid dispersions and is stable for at least a three-month period. The tablets showed good floating properties and controlled release profiles, with drug release proceeding via the concomitant operation of swelling and erosion of the polymer matrix. ANNs and GP both proved to be efficient tools in the optimization of the tablet formulation, and the global optimum formulation suggested by the GP equations consisted of PEG=9%, PVP=30%, HPMC=36%, EFF=11%, nimodipine=14%. Copyright © 2010 Elsevier B.V. All rights reserved.

Drift trajectories of a floating human body simulated in a hydraulic model of Puget Sound.

PubMed

Ebbesmeyer, C C; Haglund, W D

1994-01-01

After a young man jumped off a 221-foot (67 meters) high bridge, the drift of the body that beached 20 miles (32 km) away at Alki Point in Seattle, Washington was simulated with a hydraulic model. Simulations for the appropriate time period were performed using a small floating bead to represent the body in the hydraulic model at the University of Washington. Bead movements were videotaped and transferred to Computer Aided Drafting (AutoCAD) charts on a personal computer. Because of strong tidal currents in the narrow passage under the bridge (The Narrows near Tacoma, WA), small changes in the time of the jump (+/- 30 minutes) made large differences in the distance the body traveled (30 miles; 48 km). Hydraulic and other types of oceanographic models may be located by contacting technical experts known as physical oceanographers at local universities, and can be utilized to demonstrate trajectories of floating objects and the time required to arrive at selected locations. Potential applications for forensic death investigators include: to be able to set geographic and time limits for searches; determine potential origin of remains found floating or beached; and confirm and correlate information regarding entry into the water and sightings of remains.

Space shuttle low cost/risk avionics study

NASA Technical Reports Server (NTRS)

1971-01-01

All work breakdown structure elements containing any avionics related effort were examined for pricing the life cycle costs. The analytical, testing, and integration efforts are included for the basic onboard avionics and electrical power systems. The design and procurement of special test equipment and maintenance and repair equipment are considered. Program management associated with these efforts is described. Flight test spares and labor and materials associated with the operations and maintenance of the avionics systems throughout the horizontal flight test are examined. It was determined that cost savings can be achieved by using existing hardware, maximizing orbiter-booster commonality, specifying new equipments to MIL quality standards, basing redundancy on cost effective analysis, minimizing software complexity and reducing cross strapping and computer-managed functions, utilizing compilers and floating point computers, and evolving the design as dictated by the horizontal flight test schedules.

Stabilizing canonical-ensemble calculations in the auxiliary-field Monte Carlo method

NASA Astrophysics Data System (ADS)

Gilbreth, C. N.; Alhassid, Y.

2015-03-01

Quantum Monte Carlo methods are powerful techniques for studying strongly interacting Fermi systems. However, implementing these methods on computers with finite-precision arithmetic requires careful attention to numerical stability. In the auxiliary-field Monte Carlo (AFMC) method, low-temperature or large-model-space calculations require numerically stabilized matrix multiplication. When adapting methods used in the grand-canonical ensemble to the canonical ensemble of fixed particle number, the numerical stabilization increases the number of required floating-point operations for computing observables by a factor of the size of the single-particle model space, and thus can greatly limit the systems that can be studied. We describe an improved method for stabilizing canonical-ensemble calculations in AFMC that exhibits better scaling, and present numerical tests that demonstrate the accuracy and improved performance of the method.

Gigaflop (billion floating point operations per second) performance for computational electromagnetics

NASA Technical Reports Server (NTRS)

Shankar, V.; Rowell, C.; Hall, W. F.; Mohammadian, A. H.; Schuh, M.; Taylor, K.

1992-01-01

Accurate and rapid evaluation of radar signature for alternative aircraft/store configurations would be of substantial benefit in the evolution of integrated designs that meet radar cross-section (RCS) requirements across the threat spectrum. Finite-volume time domain methods offer the possibility of modeling the whole aircraft, including penetrable regions and stores, at longer wavelengths on today's gigaflop supercomputers and at typical airborne radar wavelengths on the teraflop computers of tomorrow. A structured-grid finite-volume time domain computational fluid dynamics (CFD)-based RCS code has been developed at the Rockwell Science Center, and this code incorporates modeling techniques for general radar absorbing materials and structures. Using this work as a base, the goal of the CFD-based CEM effort is to define, implement and evaluate various code development issues suitable for rapid prototype signature prediction.

Parallel Conjugate Gradient: Effects of Ordering Strategies, Programming Paradigms, and Architectural Platforms

NASA Technical Reports Server (NTRS)

Oliker, Leonid; Heber, Gerd; Biswas, Rupak

2000-01-01

The Conjugate Gradient (CG) algorithm is perhaps the best-known iterative technique to solve sparse linear systems that are symmetric and positive definite. A sparse matrix-vector multiply (SPMV) usually accounts for most of the floating-point operations within a CG iteration. In this paper, we investigate the effects of various ordering and partitioning strategies on the performance of parallel CG and SPMV using different programming paradigms and architectures. Results show that for this class of applications, ordering significantly improves overall performance, that cache reuse may be more important than reducing communication, and that it is possible to achieve message passing performance using shared memory constructs through careful data ordering and distribution. However, a multi-threaded implementation of CG on the Tera MTA does not require special ordering or partitioning to obtain high efficiency and scalability.

Fast neural net simulation with a DSP processor array.

PubMed

Muller, U A; Gunzinger, A; Guggenbuhl, W

1995-01-01

This paper describes the implementation of a fast neural net simulator on a novel parallel distributed-memory computer. A 60-processor system, named MUSIC (multiprocessor system with intelligent communication), is operational and runs the backpropagation algorithm at a speed of 330 million connection updates per second (continuous weight update) using 32-b floating-point precision. This is equal to 1.4 Gflops sustained performance. The complete system with 3.8 Gflops peak performance consumes less than 800 W of electrical power and fits into a 19-in rack. While reaching the speed of modern supercomputers, MUSIC still can be used as a personal desktop computer at a researcher's own disposal. In neural net simulation, this gives a computing performance to a single user which was unthinkable before. The system's real-time interfaces make it especially useful for embedded applications.

Performance Analysis of GYRO: A Tool Evaluation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Worley, P.; Roth, P.; Candy, J.

2005-06-26

The performance of the Eulerian gyrokinetic-Maxwell solver code GYRO is analyzed on five high performance computing systems. First, a manual approach is taken, using custom scripts to analyze the output of embedded wall clock timers, floating point operation counts collected using hardware performance counters, and traces of user and communication events collected using the profiling interface to Message Passing Interface (MPI) libraries. Parts of the analysis are then repeated or extended using a number of sophisticated performance analysis tools: IPM, KOJAK, SvPablo, TAU, and the PMaC modeling tool suite. The paper briefly discusses what has been discovered via this manualmore » analysis process, what performance analyses are inconvenient or infeasible to attempt manually, and to what extent the tools show promise in accelerating or significantly extending the manual performance analyses.« less

Efficient algorithms for computing a strong rank-revealing QR factorization

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gu, M.; Eisenstat, S.C.

1996-07-01

Given an m x n matrix M with m {ge} n, it is shown that there exists a permutation {Pi} and an integer k such that the QR factorization given by equation (1) reveals the numerical rank of M: the k x k upper-triangular matrix A{sub k} is well conditioned, norm of (C{sub k}){sub 2} is small, and B{sub k} is linearly dependent on A{sub k} with coefficients bounded by a low-degree polynomial in n. Existing rank-revealing QR (RRQR) algorithms are related to such factorizations and two algorithms are presented for computing them. The new algorithms are nearly as efficientmore » as QR with column pivoting for most problems and take O(mn{sup 2}) floating-point operations in the worst case.« less

A fully on-chip fast-transient NMOS low dropout voltage regulator with quasi floating gate pass element

NASA Astrophysics Data System (ADS)

Wang, Han; Gou, Chao; Luo, Kai

2017-04-01

This paper presents a fully on-chip NMOS low-dropout regulator (LDO) for portable applications with quasi floating gate pass element and fast transient response. The quasi floating gate structure makes the gate of the NMOS transistor only periodically charged or refreshed by the charge pump, which allows the charge pump to be a small economical circuit with small silicon area. In addition, a variable reference circuit is introduced enlarging the dynamic range of error amplifier during load transient. The proposed LDO has been implemented in a 0.35 μm BCD process. From experimental results, the regulator can operate with a minimum dropout voltage of 250 mV at a maximum 1 A load and {I}{{Q}} of 395 μA. Under full-range load current step, the voltage undershoot and overshoot of the proposed LDO are reduced to 50 and 26 mV, respectively.

Energy-band engineering for tunable memory characteristics through controlled doping of reduced graphene oxide.

PubMed

Han, Su-Ting; Zhou, Ye; Yang, Qing Dan; Zhou, Li; Huang, Long-Biao; Yan, Yan; Lee, Chun-Sing; Roy, Vellaisamy A L

2014-02-25

Tunable memory characteristics are used in multioperational mode circuits where memory cells with various functionalities are needed in one combined device. It is always a challenge to obtain control over threshold voltage for multimode operation. On this regard, we use a strategy of shifting the work function of reduced graphene oxide (rGO) in a controlled manner through doping gold chloride (AuCl3) and obtained a gradient increase of rGO work function. By inserting doped rGO as floating gate, a controlled threshold voltage (Vth) shift has been achieved in both p- and n-type low voltage flexible memory devices with large memory window (up to 4 times for p-type and 8 times for n-type memory devices) in comparison with pristine rGO floating gate memory devices. By proper energy band engineering, we demonstrated a flexible floating gate memory device with larger memory window and controlled threshold voltage shifts.

First and second order derivatives for optimizing parallel RF excitation waveforms.

PubMed

Majewski, Kurt; Ritter, Dieter

2015-09-01

For piecewise constant magnetic fields, the Bloch equations (without relaxation terms) can be solved explicitly. This way the magnetization created by an excitation pulse can be written as a concatenation of rotations applied to the initial magnetization. For fixed gradient trajectories, the problem of finding parallel RF waveforms, which minimize the difference between achieved and desired magnetization on a number of voxels, can thus be represented as a finite-dimensional minimization problem. We use quaternion calculus to formulate this optimization problem in the magnitude least squares variant and specify first and second order derivatives of the objective function. We obtain a small tip angle approximation as first order Taylor development from the first order derivatives and also develop algorithms for first and second order derivatives for this small tip angle approximation. All algorithms are accompanied by precise floating point operation counts to assess and compare the computational efforts. We have implemented these algorithms as callback functions of an interior-point solver. We have applied this numerical optimization method to example problems from the literature and report key observations. Copyright © 2015 Elsevier Inc. All rights reserved.

First and second order derivatives for optimizing parallel RF excitation waveforms

NASA Astrophysics Data System (ADS)

Majewski, Kurt; Ritter, Dieter

2015-09-01

For piecewise constant magnetic fields, the Bloch equations (without relaxation terms) can be solved explicitly. This way the magnetization created by an excitation pulse can be written as a concatenation of rotations applied to the initial magnetization. For fixed gradient trajectories, the problem of finding parallel RF waveforms, which minimize the difference between achieved and desired magnetization on a number of voxels, can thus be represented as a finite-dimensional minimization problem. We use quaternion calculus to formulate this optimization problem in the magnitude least squares variant and specify first and second order derivatives of the objective function. We obtain a small tip angle approximation as first order Taylor development from the first order derivatives and also develop algorithms for first and second order derivatives for this small tip angle approximation. All algorithms are accompanied by precise floating point operation counts to assess and compare the computational efforts. We have implemented these algorithms as callback functions of an interior-point solver. We have applied this numerical optimization method to example problems from the literature and report key observations.

Pointright: a system to redirect mouse and keyboard control among multiple machines

DOEpatents

Johanson, Bradley E [Palo Alto, CA; Winograd, Terry A [Stanford, CA; Hutchins, Gregory M [Mountain View, CA

2008-09-30

The present invention provides a software system, PointRight, that allows for smooth and effortless control of pointing and input devices among multiple displays. With PointRight, a single free-floating mouse and keyboard can be used to control multiple screens. When the cursor reaches the edge of a screen it seamlessly moves to the adjacent screen and keyboard control is simultaneously redirected to the appropriate machine. Laptops may also redirect their keyboard and pointing device, and multiple pointers are supported simultaneously. The system automatically reconfigures itself as displays go on, go off, or change the machine they display.

Operation Lightship

ERIC Educational Resources Information Center

Reed, Judith

1973-01-01

Describes activities abroad Liberty Chesapeake,'' a 133-foot-long retired lightship moored off the East Potomac Park, Washington, D.C., and used as a public excursion boat and floating laboratory by the U.S. National Park Service. (DS)

29 CFR 1926.912 - Underwater blasting.

Code of Federal Regulations, 2014 CFR

2014-07-01

... Underwater blasting. (a) A blaster shall conduct all blasting operations, and no shot shall be fired without... herein on handling and storing explosives. (h) When more than one charge is placed under water, a float...

29 CFR 1926.912 - Underwater blasting.

Code of Federal Regulations, 2012 CFR

2012-07-01

... Underwater blasting. (a) A blaster shall conduct all blasting operations, and no shot shall be fired without... herein on handling and storing explosives. (h) When more than one charge is placed under water, a float...

29 CFR 1926.912 - Underwater blasting.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Underwater blasting. (a) A blaster shall conduct all blasting operations, and no shot shall be fired without... herein on handling and storing explosives. (h) When more than one charge is placed under water, a float...

29 CFR 1926.912 - Underwater blasting.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Underwater blasting. (a) A blaster shall conduct all blasting operations, and no shot shall be fired without... herein on handling and storing explosives. (h) When more than one charge is placed under water, a float...

29 CFR 1926.912 - Underwater blasting.

Code of Federal Regulations, 2013 CFR

2013-07-01

... Underwater blasting. (a) A blaster shall conduct all blasting operations, and no shot shall be fired without... herein on handling and storing explosives. (h) When more than one charge is placed under water, a float...

33 CFR 207.200 - Mississippi River below mouth of Ohio River, including South and Southwest Passes; use...

Code of Federal Regulations, 2010 CFR

2010-07-01

... banks of the river, and no floating plant other than launches and similar small craft shall land against... white background readable from the waterway side, placed on each side of the river near the point where...

Feasibility study, software design, layout and simulation of a two-dimensional fast Fourier transform machine for use in optical array interferometry

NASA Technical Reports Server (NTRS)

Boriakoff, Valentin; Chen, Wei

1990-01-01

The NASA-Cornell Univ.-Worcester Polytechnic Institute Fast Fourier Transform (FFT) chip based on the architecture of the systolic FFT computation as presented by Boriakoff is implemented into an operating device design. The kernel of the system, a systolic inner product floating point processor, was designed to be assembled into a systolic network that would take incoming data streams in pipeline fashion and provide an FFT output at the same rate, word by word. It was thoroughly simulated for proper operation, and it has passed a comprehensive set of tests showing no operational errors. The black box specifications of the chip, which conform to the initial requirements of the design as specified by NASA, are given. The five subcells are described and their high level function description, logic diagrams, and simulation results are presented. Some modification of the Read Only Memory (ROM) design were made, since some errors were found in it. Because a four stage pipeline structure was used, simulating such a structure is more difficult than an ordinary structure. Simulation methods are discussed. Chip signal protocols and chip pinout are explained.

Verification of Numerical Programs: From Real Numbers to Floating Point Numbers

NASA Technical Reports Server (NTRS)

Goodloe, Alwyn E.; Munoz, Cesar; Kirchner, Florent; Correnson, Loiec

2013-01-01

Numerical algorithms lie at the heart of many safety-critical aerospace systems. The complexity and hybrid nature of these systems often requires the use of interactive theorem provers to verify that these algorithms are logically correct. Usually, proofs involving numerical computations are conducted in the infinitely precise realm of the field of real numbers. However, numerical computations in these algorithms are often implemented using floating point numbers. The use of a finite representation of real numbers introduces uncertainties as to whether the properties veri ed in the theoretical setting hold in practice. This short paper describes work in progress aimed at addressing these concerns. Given a formally proven algorithm, written in the Program Verification System (PVS), the Frama-C suite of tools is used to identify sufficient conditions and verify that under such conditions the rounding errors arising in a C implementation of the algorithm do not affect its correctness. The technique is illustrated using an algorithm for detecting loss of separation among aircraft.

Floating-Point Modules Targeted for Use with RC Compilation Tools

NASA Technical Reports Server (NTRS)

Sahin, Ibrahin; Gloster, Clay S.

2000-01-01

Reconfigurable Computing (RC) has emerged as a viable computing solution for computationally intensive applications. Several applications have been mapped to RC system and in most cases, they provided the smallest published execution time. Although RC systems offer significant performance advantages over general-purpose processors, they require more application development time than general-purpose processors. This increased development time of RC systems provides the motivation to develop an optimized module library with an assembly language instruction format interface for use with future RC system that will reduce development time significantly. In this paper, we present area/performance metrics for several different types of floating point (FP) modules that can be utilized to develop complex FP applications. These modules are highly pipelined and optimized for both speed and area. Using these modules, and example application, FP matrix multiplication, is also presented. Our results and experiences show, that with these modules, 8-10X speedup over general-purpose processors can be achieved.

Fortran Program for X-Ray Photoelectron Spectroscopy Data Reformatting

NASA Technical Reports Server (NTRS)

Abel, Phillip B.

1989-01-01

A FORTRAN program has been written for use on an IBM PC/XT or AT or compatible microcomputer (personal computer, PC) that converts a column of ASCII-format numbers into a binary-format file suitable for interactive analysis on a Digital Equipment Corporation (DEC) computer running the VGS-5000 Enhanced Data Processing (EDP) software package. The incompatible floating-point number representations of the two computers were compared, and a subroutine was created to correctly store floating-point numbers on the IBM PC, which can be directly read by the DEC computer. Any file transfer protocol having provision for binary data can be used to transmit the resulting file from the PC to the DEC machine. The data file header required by the EDP programs for an x ray photoelectron spectrum is also written to the file. The user is prompted for the relevant experimental parameters, which are then properly coded into the format used internally by all of the VGS-5000 series EDP packages.

Video- Demonstration of Tea and Sugar in Water Onboard the International Space Station (ISS)

NASA Technical Reports Server (NTRS)

2003-01-01

Saturday Morning Science, the science of opportunity series of applied experiments and demonstrations, performed aboard the International Space Station (ISS) by Expedition 6 astronaut Dr. Don Pettit, revealed some remarkable findings. Imagine what would happen if a collection of loosely attractive particles were confined in a relatively small region in the floating environment of space. Would they self organize into a compact structure, loosely organize into a fractal, or just continue to float around in their container? In this video clip, Dr. Pettit explored the possibilities. At one point he remarks, 'These things look like pictures from the Hubble Space Telescope.' Watch the video and see what happens!

Fluidic lens of floating oil using round-pot chamber based on electrowetting.

PubMed

Choi, Hyunhwan; Won, Yonghyub

2013-07-01

This study presents a liquid lens using electrowetting that employs an oil phase floating in between the conducting fluids. The lens shape has double-sided surfaces and operates with a bias of 0-60 V. The focal length of the lens, with an aperture size of 2 mm, is ~5.8 mm, and it is converted into an optical power of 172. The lens is sufficient to suppress the fluctuation of fluids due to the external vibration. An image seen through the lens clearly resolves the element better than 6.35 LP/mm on USAF 1951 1×.